New technologies for PCB [polychlorinated biphenyl] decontamination

International Nuclear Information System (INIS)

Webber, I.

1993-01-01

Polychlorinated biphenyls (PCB) were mixed with chlorobenzenes to reduce viscosity and provide for both electrical insulation and convective heat transfers. These mixtures were known as askarels, and ca 99.8% of PCBs used in electrical applications are contained in askarel-filled transformers and capacitors. It is estimated that there are ca 180 million gal of PCB-contaminated oil distributed through over 3 million transformers in the USA. Technology used for decontaminating these transformers depends on the concentration of the PCB contamination. At low PCB concentrations of up to ca 2,000 ppM, chemical methods can be used; at higher concentrations, alternative disposal options become more attractive. For chemical treatment, a small mobile unit using quick-reacting reagents has been developed for on-site decontamination. For highly contaminated transformers, retrofilling is very attractive since the owner's liability is minimized at minimum cost. Conventional flush/drain procedures have such drawbacks as the inability to remove oil trapped in windings and the leaching of trapped PCBs back into the uncontaminated retrofill oil over time. A new process has been developed to solve the leaching problem and to decontaminate the drained askarel at room temperature using a catalyst. An alternative disposal strategy involves dismantling the transformer carcass, incinerating non-recyclable materials, and cleaning the metals and wire with solvent. 8 figs

Remediation of PCB [polychlorinated biphenyl] -contaminated soils from scrapyards

International Nuclear Information System (INIS)

MacKnight, S.

1991-01-01

Much of the recent attention on contamination of the environment by polychlorinated biphenyls (PCB) has focused on liquid PCB spills from electrical equipment. A new, and possibly more serious, source of PCB contamination is the scrap yard, typically located in or near major urban centers, where the local scrap dealer would purchase used transformers or other PCB-containing electrical equipment, recover copper and other metals, and dump the PCB-containing oils on the ground. With the rising value of urban and suburban lands, these scrap yards may be slated for redevelopment, making the cleanup of contaminated soils necessary. The heterogeneous distribution of scrap yard contaminants requires a very detailed site assessment, and the heterogeneous mixture of typical scrap yard contaminants (not only PCB) cannot be treated in a simple fashion. These problems are illustrated for the case of the assessment and cleanup of a scrap yard site in Nova Scotia. A grid block system was used to sample soil at the site, and samples were analyzed for PCB, metals, and hydrocarbons. The most severely contaminated spots were mapped; groundwater patterns were also examined. The remediation process can be divided into 5 phases: physical separation of uncontaminated material; three stages of separation of materials into those having single, several-but-similar, and multicomponent mixed contaminations; and selection of appropriate process technologies. Since there is currently no approved PCB destruction facility in Atlantic Canada, excavated soils containing PCB are stored securely on the site to await approval for some type of incineration process

RESEARCH ON ENVIRONMENTAL CONTAMINATION IN RAW MILK IN TURIN DEPARTEMENT : HEAVY METALS, P.C.B, ORGANOCHLORINE AND ORGANOPHOSPHORUS PESTICIDES – YEARS 2005 – 2008

Directory of Open Access Journals (Sweden)

S. Cavallera

2013-02-01

Full Text Available In the period between 2005 and 2008 was carried out a survey on 252 samples of raw bovine milk collected in Turin departement to certain levels of contamination by heavy metals (Cd, Cr, Fe, Hg, Pb, Zn, PCB and organophosphorus and organochlorine pesticides. These results argue that the levels of heavy metals, PCB and pesticides are well below what is expected by the European legislation and that the situation is under control and that raw milk meets the hygiene requirements for human health.

Risk-Based Disposal Plan for PCB Paint in the TRA Fluorinel Dissolution Process Mockup and Gamma Facilities Canal

Energy Technology Data Exchange (ETDEWEB)

R. A. Montgomery

2008-05-01

This Toxic Substances Control Act Risk-Based Polychlorinated Biphenyl Disposal plan was developed for the Test Reactor Area Fluorinel Dissolution Process Mockup and Gamma Facilities Waste System, located in Building TRA-641 at the Reactor Technology Complex, Idaho National Laboratory Site, to address painted surfaces in the empty canal under 40 CFR 761.62(c) for paint, and under 40 CFR 761.61(c) for PCBs that may have penetrated into the concrete. The canal walls and floor will be painted with two coats of contrasting non-PCB paint and labeled as PCB. The canal is covered with open decking; the access grate is locked shut and signed to indicate PCB contamination in the canal. Access to the canal will require facility manager permission. Protective equipment for personnel and equipment entering the canal will be required. Waste from the canal, generated during ultimate Decontamination and Decommissioning, shall be managed and disposed as PCB Bulk Product Waste.

Cast bulk metallic glass alloys: prospects as wear materials

Energy Technology Data Exchange (ETDEWEB)

Hawk, Jeffrey A.; Dogan, Omer N.; Shiflet, Gary J. (Dept. of Materials Science and Engineering, University of Virginia, Charlottesville, VA)

2005-01-01

Bulk metallic glasses are single phase materials with unusual physical and mechanical properties. One intriguing area of possible use is as a wear material. Usually, pure metals and single phase dilute alloys do not perform well in tribological conditions. When the metal or alloy is lightweight, it is usually soft leading to galling in sliding situations. For the harder metals and alloys, their density is usually high, so there is an energy penalty when using these materials in wear situations. However, bulk metallic glasses at the same density are usually harder than corresponding metals and dilute single phase alloys, and so could offer better wear resistance. This work will discuss preliminary wear results for metallic glasses with densities in the range of 4.5 to 7.9 g/cc. The wear behavior of these materials will be compared to similar metals and alloys.

Recent changes in federal PCB regulations

International Nuclear Information System (INIS)

Ewing, H.

1995-01-01

An overview of the federal regulations dealing with PCBs, the draft PCB Transformer Decontamination Standards and Protocols, and the Practice of Ballast Splitting was given. Answers were provided to practical questions concerning the regulations, specifically, responsibility for storage, labelling requirements, waste export regulations, treatment and destruction standards, transformer decontamination, decontamination standards, and the practice of ballast splitting into PCB and non-PCB materials. Details of sampling procedures and sample handling were also described

PCB in soils and estimated soil-air exchange fluxes of selected PCB congeners in the south of Sweden

International Nuclear Information System (INIS)

Backe, Cecilia; Cousins, Ian T.; Larsson, Per

2004-01-01

PCB concentrations were studied in different soils to determine the spatial variation over a region of approximately 11 000 km 2 . PCB congener pattern was used to illustrate the spatial differences, as shown by principal component analysis (PCA). The relationship to different soil parameters was studied. PCB concentrations in soil showed a large variation between sampling-areas with median concentrations ranging between 2.3 and 332 ng g -1 (dw). Highest concentrations were found at two sites with sandy soils, one with extremely high organic carbon content. Both sites were located on the west coast of southern Sweden. Soils with similar soil textures (i.e. sandy silt moraine) did not show any significant differences in PCB concentrations. PCB congener composition was shown to differ between sites, with congener patterns almost site-specific. PCB in air and precipitation was measured and the transfer of chemicals between the soil and air compartments was estimated. Soil-air fugacity quotient calculations showed that the PCBs in the soil consistently had a higher fugacity than the PCBs in the air, with a median quotient value of 2.7. The gaseous fluxes between soil and air were estimated using standard modelling equations and a net soil-air flux estimated by subtracting bulk deposition from gaseous soil-air fluxes. It was shown that inclusion of vertical sorbed phase transport of PCBs in the soil had a large effect on the direction of the net soil-air exchange fluxes. - Soil-air exchange of PCBs is investigated and modelled across Sweden

Internal shear cracking in bulk metal forming

DEFF Research Database (Denmark)

Christiansen, Peter; Nielsen, Chris Valentin; Bay, Niels Oluf

2017-01-01

This paper presents an uncoupled ductile damage criterion for modelling the opening and propagation of internal shear cracks in bulk metal forming. The criterion is built upon the original work on the motion of a hole subjected to shear with superimposed tensile stress triaxiality and its overall...... performance is evaluated by means of side-pressing formability tests in Aluminium AA2007-T6 subjected to different levels of pre-strain. Results show that the new proposed criterionis able to combine simplicity with efficiency for predicting the onset of fracture and the crack propagation path for the entire...... cracking to internal cracks formed undert hree-dimensional states of stress that are typical of bulk metal forming....

Non-isothermal crystallization kinetics and fragility of (Cu46Zr47Al7)97Ti3 bulk metallic glass investigated by differential scanning calorimetry

International Nuclear Information System (INIS)

Zhu, Man; Li, Junjie; Yao, Lijuan; Jian, Zengyun; Chang, Fang’e; Yang, Gencang

2013-01-01

Highlights: • Non-isothermal crystallization kinetics of (Cu 46 Zr 47 Al 7 ) 97 Ti 3 BMGs was studied. • Two-stage of crystallization process is confirmed by DSC. • The nucleation process is difficult than growth process during crystallization. • The second crystallization process is the most sensitive to heating rate. • Kinetic fragility index is evaluated suggesting it is an intermediate glass. - Abstract: In this paper, bulk metallic glasses with the composition of (Cu 46 Zr 47 Al 7 ) 97 Ti 3 were prepared by copper mold casting technique. X-ray diffraction (XRD) and differential scanning calorimetry (DSC) were used to investigate its structure and non-isothermal crystallization kinetics. DSC traces revealed that it undergoes two-stage crystallization. The activation energies corresponding to the characteristic temperatures have been calculated, and the results reveal that the as-cast alloys have a good thermal stability in thermodynamics. Based on Kissinger equation, the activation energies for glass transition, the first and second crystallization processes were obtained as 485 ± 16 kJ/mol, 331 ± 7 kJ/mol and 210 ± 3 kJ/mol, respectively, suggesting that the nucleation process is more difficult than the grain growth process. The fitting curves using Lasocka's empirical relation show that the influence of the heating rate for crystallization is larger than glass transition. Furthermore, the kinetic fragility for (Cu 46 Zr 47 Al 7 ) 97 Ti 3 bulk metallic glasses is evaluated. Depending on the fragility index, (Cu 46 Zr 47 Al 7 ) 97 Ti 3 bulk metallic glasses should be considered as “intermediate glasses”

Use of large pieces of printed circuit boards for bioleaching to avoid 'precipitate contamination problem' and to simplify overall metal recovery.

Science.gov (United States)

Adhapure, N N; Dhakephalkar, P K; Dhakephalkar, A P; Tembhurkar, V R; Rajgure, A V; Deshmukh, A M

2014-01-01

Very recently bioleaching has been used for removing metals from electronic waste. Most of the research has been targeted to using pulverized PCBs for bioleaching where precipitate formed during bioleaching contaminates the pulverized PCB sample and making the overall metal recovery process more complicated. In addition to that, such mixing of pulverized sample with precipitate also creates problems for the final separation of non metallic fraction of PCB sample. In the present investigation we attempted the use of large pieces of printed circuit boards instead of pulverized sample for removal of metals. Use of large pieces of PCBs for bioleaching was restricted due to the chemical coating present on PCBs, the problem has been solved by chemical treatment of PCBs prior to bioleaching. In short,•Large pieces of PCB can be used for bioleaching instead of pulverized PCB sample.•Metallic portion on PCBs can be made accessible to bacteria with prior chemical treatment of PCBs.•Complete metal removal obtained on PCB pieces of size 4 cm × 2.5 cm with the exception of solder traces. The final metal free PCBs (non metallic) can be easily recycled and in this way the overall recycling process (metallic and non metallic part) of PCBs becomes simple.

Evaluation and interconversion of various indicator PCB schemes for ∑PCB and dioxin-like PCB toxic equivalent levels in fish.

Science.gov (United States)

Gandhi, Nilima; Bhavsar, Satyendra P; Reiner, Eric J; Chen, Tony; Morse, Dave; Arhonditsis, George B; Drouillard, Ken G

2015-01-06

Polychlorinated biphenyls (PCBs) remain chemicals of concern more than three decades after the ban on their production. Technical mixture-based total PCB measurements are unreliable due to weathering and degradation, while detailed full congener specific measurements can be time-consuming and costly for large studies. Measurements using a subset of indicator PCBs (iPCBs) have been considered appropriate; however, inclusion of different PCB congeners in various iPCB schemes makes it challenging to readily compare data. Here, using an extensive data set, we examine the performance of existing iPCB3 (PCB 138, 153, and 180), iPCB6 (iPCB3 plus 28, 52, and 101) and iPCB7 (iPCB6 plus 118) schemes, and new iPCB schemes in estimating total of PCB congeners (∑PCB) and dioxin-like PCB toxic equivalent (dlPCB-TEQ) concentrations in sport fish fillets and the whole body of juvenile fish. The coefficients of determination (R(2)) for regressions conducted using logarithmically transformed data suggest that inclusion of an increased number of PCBs in an iPCB improves relationship with ∑PCB but not dlPCB-TEQs. Overall, novel iPCB3 (PCB 95, 118, and 153), iPCB4 (iPCB3 plus 138) and iPCB5 (iPCB4 plus 110) presented in this study and existing iPCB6 and iPCB7 are the most optimal indicators, while the current iPCB3 should be avoided. Measurement of ∑PCB based on a more detailed analysis (50+ congeners) is also overall a good approach for assessing PCB contamination and to track PCB origin in fish. Relationships among the existing and new iPCB schemes have been presented to facilitate their interconversion. The iPCB6 equiv levels for the 6.5 and 10 pg/g benchmarks of dlPCB-TEQ05 are about 50 and 120 ng/g ww, respectively, which are lower than the corresponding iPCB6 limits of 125 and 300 ng/g ww set by the European Union.

Microbial decomposition of PCB. PCB no biseibutsu bunkai

Energy Technology Data Exchange (ETDEWEB)

Furukawa, K [Kyushu University, Fukuoka (Japan). Faculty of Agriculture

1993-08-01

This paper generalizes knowledges acquired so far on bio-remediation of PCB. Aerobic PCB decomposition using soil bacteria generally goes through introduction of O2 into second and third orders of a biphenyl ring, ring cleavage, and hydrolysis, and generates benzoate finally. PCB that is decomposed in this 2, 3-dioxygenaze path requires at least one of the second and third orders to be open. The decomposition through this path becomes difficult when the number of displaced Cl increases, and PCB with Cl displaced in only one of the rings decomposes more easily than PCB with the same number of Cl in both rings. A group in GE, Inc. has searched for two kinds of bacteria stocks that introduce O2 preferentially into the third and fourth orders. These stocks decompose third and fourth ordered open high-chlorine PCB. Groups in GE, Inc. and other companies have isolated bacteria that dechlorinate PCB decreasingly under an anaerobic condition. These bacteria desorb metha-ordered chlorine. Discussions are being made on cloning of PCB decomposing genes, and breeding of decomposing bacteria that have wide PCB decomposing spectra. 22 refs., 8 figs., 2 tabs.

Use of large pieces of printed circuit boards for bioleaching to avoid ‘precipitate contamination problem’ and to simplify overall metal recovery

Science.gov (United States)

Adhapure, N.N.; Dhakephalkar, P.K.; Dhakephalkar, A.P.; Tembhurkar, V.R.; Rajgure, A.V.; Deshmukh, A.M.

2014-01-01

Very recently bioleaching has been used for removing metals from electronic waste. Most of the research has been targeted to using pulverized PCBs for bioleaching where precipitate formed during bioleaching contaminates the pulverized PCB sample and making the overall metal recovery process more complicated. In addition to that, such mixing of pulverized sample with precipitate also creates problems for the final separation of non metallic fraction of PCB sample. In the present investigation we attempted the use of large pieces of printed circuit boards instead of pulverized sample for removal of metals. Use of large pieces of PCBs for bioleaching was restricted due to the chemical coating present on PCBs, the problem has been solved by chemical treatment of PCBs prior to bioleaching. In short,•Large pieces of PCB can be used for bioleaching instead of pulverized PCB sample.•Metallic portion on PCBs can be made accessible to bacteria with prior chemical treatment of PCBs.•Complete metal removal obtained on PCB pieces of size 4 cm × 2.5 cm with the exception of solder traces. The final metal free PCBs (non metallic) can be easily recycled and in this way the overall recycling process (metallic and non metallic part) of PCBs becomes simple. PMID:26150951

Dioxin-like PCB in indoor air contaminated with different sources

Energy Technology Data Exchange (ETDEWEB)

Heinzow, B.G.J.; Mohr, S.; Ostendorp, G. [Landesamt fuer Gesundheit und Arbeitssicherheit des Landes Schleswig-Holstein, Flintbek (Germany); Kerst, M.; Koerner, W. [Bayerisches Landesamt fuer Umweltschutz, Augsburg (Germany)

2004-09-15

Polychlorinated biphenyls (PCB) have been used in public building constructions for various purposes in the 1960s and 1970s, mainly as an additive to concrete, caulking, grout, paints, as a major constitutent of permanent elastic Thiokol rubber sealants and flame retardant coatings of acoustic ceiling tiles. Offgazing of semivolatile PCB from building materials can nowadays still result in considerable house-dust contamination and in indoor air concentrations exceeding 10,000 ng/m{sup 3}. In Germany, PCB levels in indoor air in non-occupational settings have been regulated with a tolerable total PCB concentration of 300 ng /m{sup 3} and an intervention level of 3000 ng/m{sup 3}. Lower re-entry criteria have been proposed by Michaud et al. Technical mixtures of PCB contain dioxin-like non- and mono-ortho substituted PCB congeners and are contaminated with trace amounts of polychlorinated dibenzodioxins (PCDD) and mainly dibenzofurans (PCDF), sharing overlapping toxic effects and physicochemical properties. We report here on levels of dioxinlike PCB measured in buildings with various PCB sources and correlations among PCDD/PCDF and dioxin-like PCB and di-ortho PCB.

Zr-(Cu,Ag)-Al bulk metallic glasses

International Nuclear Information System (INIS)

Jiang, Q.K.; Wang, X.D.; Nie, X.P.; Zhang, G.Q.; Ma, H.; Fecht, H.-J.; Bendnarcik, J.; Franz, H.; Liu, Y.G.; Cao, Q.P.; Jiang, J.Z.

2008-01-01

In this paper, we report the formation of a series Zr-(Cu,Ag)-Al bulk metallic glasses (BMGs) with diameters at least 20 mm and demonstrate the formation of about 25 g amorphous metallic ingots in a wide Zr-(Cu,Ag)-Al composition range using a conventional arc-melting machine. The origin of high glass-forming ability (GFA) of the Zr-(Cu,Ag)-Al alloy system has been investigated from the structural, thermodynamic and kinetic points of view. The high GFA of the Zr-(Cu,Ag)-Al system is attributed to denser local atomic packing and the smaller difference in Gibbs free energy between amorphous and crystalline phases. The thermal, mechanical and corrosion properties, as well as elastic constants for the newly developed Zr-(Cu,Ag)-Al BMGs, are also presented. These newly developed Ni-free Zr-(Cu,Ag)-Al BMGs exhibit excellent combined properties: strong GFA, high strength, high compressive plasticity, cheap and non-toxic raw materials and biocompatible property, as compared with other BMGs, leading to their potential industrial applications

Linking structure to fragility in bulk metallic glass-forming liquids

International Nuclear Information System (INIS)

Wei, Shuai; Stolpe, Moritz; Gross, Oliver; Gallino, Isabella; Hembree, William; Busch, Ralf; Evenson, Zach; Bednarcik, Jozef; Kruzic, Jamie J.

2015-01-01

Using in-situ synchrotron X-ray scattering, we show that the structural evolution of various bulk metallic glass-forming liquids can be quantitatively connected to their viscosity behavior in the supercooled liquid near T g . The structural signature of fragility is identified as the temperature dependence of local dilatation on distinct key atomic length scales. A more fragile behavior results from a more pronounced thermally induced dilatation of the structure on a length scale of about 3 to 4 atomic diameters, coupled with shallower temperature dependence of structural changes in the nearest neighbor environment. These findings shed light on the structural origin of viscous slowdown during undercooling of bulk metallic glass-forming liquids and demonstrate the promise of predicting the properties of bulk metallic glasses from the atomic scale structure

Linking structure to fragility in bulk metallic glass-forming liquids

Energy Technology Data Exchange (ETDEWEB)

Wei, Shuai, E-mail: shuai.wei@asu.edu, E-mail: m.stolpe@mx.uni-saarland.de [Department of Materials Science and Engineering, Saarland University, Campus C63, 66123 Saarbrücken (Germany); Department of Chemistry and Biochemistry, Arizona State University, Tempe, Arizona 85287 (United States); Stolpe, Moritz, E-mail: shuai.wei@asu.edu, E-mail: m.stolpe@mx.uni-saarland.de; Gross, Oliver; Gallino, Isabella; Hembree, William; Busch, Ralf [Department of Materials Science and Engineering, Saarland University, Campus C63, 66123 Saarbrücken (Germany); Evenson, Zach [Department of Materials Science and Engineering, Saarland University, Campus C63, 66123 Saarbrücken (Germany); Institut für Materialphysik im Weltraum, Deutsches Zentrum für Luft- und Raumfahrt (DLR), 51170 Köln (Germany); Bednarcik, Jozef [Deutsches Elektronen-Synchrotron DESY, Notkestrasse 85, D-22603 Hamburg (Germany); Kruzic, Jamie J. [Material Science, School of Mechanical, Industrial, and Manufacturing Engineering, Oregon State University, Corvallis, Oregon 97331 (United States)

2015-05-04

Using in-situ synchrotron X-ray scattering, we show that the structural evolution of various bulk metallic glass-forming liquids can be quantitatively connected to their viscosity behavior in the supercooled liquid near T{sub g}. The structural signature of fragility is identified as the temperature dependence of local dilatation on distinct key atomic length scales. A more fragile behavior results from a more pronounced thermally induced dilatation of the structure on a length scale of about 3 to 4 atomic diameters, coupled with shallower temperature dependence of structural changes in the nearest neighbor environment. These findings shed light on the structural origin of viscous slowdown during undercooling of bulk metallic glass-forming liquids and demonstrate the promise of predicting the properties of bulk metallic glasses from the atomic scale structure.

Forming of bulk metallic glass microcomponents

DEFF Research Database (Denmark)

Wert, John A.; Thomsen, Christian; Jensen, Rune Debel

2009-01-01

The present article considers forward extrusion, closed-die forging and backward extrusion processes for fabrication of individual microcomponents from two bulk metallic glass (BMG) compositions: Mg60Cu30Y10 and Zr44Cu40Ag8Al8. Two types of tooling were used in the present work: relatively massive...... die sets characteristic of cold forming operations for crystalline metals and lightweight die sets adapted to the special characteristics of BMGs. In addition to demonstrating that microcomponents of several geometries can be readily fabricated from BMGs, rheological properties are combined...

Hydrogen-induced high damping of bulk metallic glasses

International Nuclear Information System (INIS)

Hasegawa, M.

2009-01-01

There are two important topics concerned with the recent researches on the damping materials of hydrogenated metallic glasses (HMGs). One is the mechanism of the high hydrogen-induced internal friction of HMGs. The other is the materials processing of 'bulk' HMGs for engineering. This article describes the summary of our recent studies on these topics. The first one is closely related to the local structure of the metallic glasses. Therefore, our recent results on the intermediate-range local structure of the simple two Zr-based metallic glasses are described, which has been clarified by the Voronoi analysis using the experimental data of the neutron diffraction measurements. The hydrogen-induced internal friction of HMGs is also discussed on the basis of these recent results of the local structure of the metallic glasses. In terms of the second topic, the first successful preparation of heavily hydrogenated Zr-based bulk HMG rods without hydrogen-induced surface embrittlement is described. They are prepared by a powder-compact-melting and liquid-casting process using Zr-Al-Ni-Cu metallic glass and ZrH 2 powders as the starting materials. It has been found that they have high damping properties.

40 CFR 761.350 - Subsampling from composite samples.

Science.gov (United States)

2010-07-01

... chemical extraction and analysis laboratory for further subsampling. There are two options for the... container, approved for shipment of the sample, to the chemical extraction and analysis laboratory, for the..., AND USE PROHIBITIONS Sampling Non-Liquid, Non-Metal PCB Bulk Product Waste for Purposes of...

Transcriptomics identifies differences between ultrapure non-dioxin-like polychlorinated biphenyls (PCBs) and dioxin-like PCB126 in cultured peripheral blood mononuclear cells

International Nuclear Information System (INIS)

Wens, B.; De Boever, P.; Maes, M.; Hollanders, K.; Schoeters, G.

2011-01-01

Polychlorinated biphenyls (PCBs) remain ubiquitously present in human lipids despite the ban on their production and use. Their presence can be chemically monitored in peripheral blood samples of the general population. We tested whether in vitro exposure to different PCB congeners induced different gene expression profiles in peripheral blood cells. We have isolated peripheral blood mononuclear cells (PBMC) from whole blood of 8 healthy individuals and exposed these cells in vitro to individual non-dioxin-like (NDL)-PCB congeners (PCB52, 138 or 180; 10 μM) or dioxin-like (DL)-PCB congener PCB126 (1 μM) during 18 h. Differential gene expression response was measured using Agilent whole-human genome microarrays. Two-way ANOVA analysis of the data showed that both gender and PCB exposure are important factors influencing gene expression responses in blood cells. Hierarchical cluster analysis of genes influenced by PCB exposure, revealed that DL-PCB126 induced a different gene expression response compared to the NDL-PCBs. Biological interpretation of the results revealed that exposure to PCB126 induced the AhR signaling pathway, whereas the induction of nuclear receptor pathways by the NDL-PCBs was limited in blood cells. Nevertheless, molecular responses of blood cells to individual PCB congeners revealed significantly expressed genes that play a role in biological functions and processes known to be affected by PCB exposure in vivo. Observed gene expression changes in this in vitro model were found to be related to hepatotoxicity, immune and inflammatory response and disturbance of lipid and cholesterol homeostasis.

Bulk viscosity and ultrasonic attenuation in liquid metals

International Nuclear Information System (INIS)

Awasthi, O.N.; Murthy, B.V.S.

1984-11-01

Ultrasonic attenuation in simple liquid metals has been investigated using the thermodynamic theory of relaxation processes incorporating the concept of a two state model for the liquid near the melting point. Agreement of the results with the experimental values of the ultrasonic attenuation and bulk viscosity indicates that this might be an appropriate approach to explain the excess attenuation of ultrasonic waves in liquid metals. (author)

Failure by fracture in bulk metal forming

DEFF Research Database (Denmark)

Silva, C.M.A.; Alves, Luis M.; Nielsen, Chris Valentin

2015-01-01

This paper revisits formability in bulk metal forming in the light of fundamental concepts of plasticity,ductile damage and crack opening modes. It proposes a new test to appraise the accuracy, reliability and validity of fracture loci associated with crack opening by tension and out-of-plane shear...

Comparison of the in vitro effects of TCDD, PCB 126 and PCB 153 on thyroid-restricted gene expression and thyroid hormone secretion by the chicken thyroid gland.

Science.gov (United States)

Katarzyńska, Dorota; Hrabia, Anna; Kowalik, Kinga; Sechman, Andrzej

2015-03-01

The aim of this study was to compare the in vitro effects of 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD), 3,3',4,4',5-pentachlorobiphenyl (PCB 126; a coplanar PCB congener) and 2,2'4,4',5,5'-hexachlorobiphenyl (PCB153; non-coplanar PCB) on mRNA expression of thyroid-restricted genes, i.e. sodium iodide symporter (NIS), thyroid peroxidase (TPO) and thyroglobulin (TG), and thyroid hormone secretion from the thyroid gland of the laying chicken. Relative expression levels of NIS, TG and TPO genes and thyroxine (T4) and triiodothyronine (T3) secretion from the thyroidal explants were quantified by the real-time qPCR and RIA methods, respectively. In comparison with the control group, TCDD and PCB 126 significantly increased mRNA expression of TPO and TG genes. TCDD did not affect NIS mRNA levels, but PCB 126 decreased its expression. No effect of PCB 153 on the expression of these genes was observed. TCDD and PCB 126 significantly decreased T4 and T3 secretion. There was no significant effect of PCB 153 on these hormone secretions. In conclusion, the results obtained show that in comparison with non-coplanar PCB 153, TCDD and coplanar PCB 126 can directly affect thyroid hormone synthesis and secretion, and in consequence, they may disrupt the endocrine function of the thyroid gland of the laying chicken. Copyright © 2015 Elsevier B.V. All rights reserved.

Flow and Fracture of Bulk Metallic Glass Alloys and their Composites

International Nuclear Information System (INIS)

Flores, K M; Suh, D; Howell, R; Asoka-Kumar, P; Dauskardt, R H

2001-01-01

The fracture and plastic deformation mechanisms of a Zr-Ti-Ni-Cu-Be bulk metallic glass and a composite utilizing a crystalline reinforcement phase are reviewed. The relationship between stress state, free volume and shear band formation are discussed. Positron annihilation techniques were used to confirm the predicted increase in free volume after plastic straining. Strain localization and failure were examined for a wide range of stress states. Finally, methods for toughening metallic glasses are considered. Significant increases in toughness are demonstrated for a composite bulk metallic glass containing a ductile second phase which stabilizes shear band formation and distributes plastic deformation

Thulium-based bulk metallic glass

International Nuclear Information System (INIS)

Yu, H. B.; Yu, P.; Wang, W. H.; Bai, H. Y.

2008-01-01

We report the formation and properties of a thulium-based bulk metallic glass (BMG). Compared with other known rare-earth (RE) based BMGs, Tm-based BMGs show features of excellent glass formation ability, considerable higher elastic modulus, smaller Poisson's ratio, high mechanical strength, and intrinsic brittleness. The reasons for the different properties between the Tm-based and other RE-based BMGs are discussed. It is expected that the Tm-based glasses with the unique properties are appropriate candidates for studying some important issues in BMGs

Corrosion of Metal Inclusions In Bulk Vitrification Waste Packages

Energy Technology Data Exchange (ETDEWEB)

Bacon, Diana H.; Pierce, Eric M.; Wellman, Dawn M.; Strachan, Denis M.; Josephson, Gary B.

2006-07-31

The primary purpose of the work reported here is to analyze the potential effect of the release of technetium (Tc) from metal inclusions in bulk vitrification waste packages once they are placed in the Integrated Disposal Facility (IDF). As part of the strategy for immobilizing waste from the underground tanks at Hanford, selected wastes will be immobilized using bulk vitrification. During analyses of the glass produced in engineering-scale tests, metal inclusions were found in the glass product. This report contains the results from experiments designed to quantify the corrosion rates of metal inclusions found in the glass product from AMEC Test ES-32B and simulations designed to compare the rate of Tc release from the metal inclusions to the release of Tc from glass produced with the bulk vitrification process. In the simulations, the Tc in the metal inclusions was assumed to be released congruently during metal corrosion as soluble TcO4-. The experimental results and modeling calculations show that the metal corrosion rate will, under all conceivable conditions at the IDF, be dominated by the presence of the passivating layer and corrosion products on the metal particles. As a result, the release of Tc from the metal particles at the surfaces of fractures in the glass releases at a rate similar to the Tc present as a soluble salt. The release of the remaining Tc in the metal is controlled by the dissolution of the glass matrix. To summarize, the release of 99Tc from the BV glass within precipitated Fe is directly proportional to the diameter of the Fe particles and to the amount of precipitated Fe. However, the main contribution to the Tc release from the iron particles is over the same time period as the release of the soluble Tc salt. For the base case used in this study (0.48 mass% of 0.5 mm diameter metal particles homogeneously distributed in the BV glass), the release of 99Tc from the metal is approximately the same as the release from 0.3 mass% soluble Tc

Tuning apparent friction coefficient by controlled patterning bulk metallic glasses surfaces

Science.gov (United States)

Li, Ning; Xu, Erjiang; Liu, Ze; Wang, Xinyun; Liu, Lin

2016-12-01

Micro-honeycomb structures with various pitches between adjacent cells were hot-embossed on Zr35Ti30Cu8.25Be26.75 bulk metallic glass surface. The effect of pitch geometry on the frictional behavior of metallic glass surface was systematically investigated. The results revealed that all textured metallic glass surfaces show a reduction in friction coefficient compared to smooth surface. More intriguingly, the friction coefficient first decreased and then increased gradually with increasing pitches. Such unique behavior can be understood fundamentally from the perspective of competing effects between contact area and local stress level with increasing pitches. This finding not only enhance the in-depth understanding of the mechanism of the significant role of surface topography on the frictional behavior of metallic glass surface, but also opens a new route towards other functional applications for bulk metallic glasses.

Free standing bulk metallic glass microcomponents: Tooling considerations

DEFF Research Database (Denmark)

Byrne, Cormac; Eldrup, Morten Mostgaard; Ohnuma, Masato

2010-01-01

Bulk metallic glasses have enormous potential for use in small-scale devices such as MEMS and biomedical components. Thermoplastic forging of free standing components poses challenges unlike those seen when forging crystalline materials. Central to these challenges is the simultaneous advantage/disadvantage...

Bulk-plasmon contribution to the work function of metals

International Nuclear Information System (INIS)

Gutierrez, F A; DIaz-Valdes, J; Jouin, H

2007-01-01

By consideration of the Koopmans theorem expression for the work function of a metal, we find that the total height of the surface barrier potential equals the value of the bulk-plasmon energy of pure metals. As a consequence a simple formula for the work function is obtained which shows better agreement with the experimental data than the most complete existent theories

An assessment of PCB degradation by microogransims including methods for measuring mineralization

International Nuclear Information System (INIS)

Hadden, C.; Edenborn, H.; Osborne, T.; Holdsworth, G.; Revis, N.

1990-01-01

These studies sought to isolate and identify organism(s) from PCB contaminated soil and sediment that degrade PCB; to provide information on the potential of organisms in soil samples taken from a PCB-contaminated area to mineralize or dechlorinate PCB congeners; to assess potential enhancement of PCB biodegradation as a result of nutritional amendment of the samples; and to carry out analyses of successive lysimeter samples to determine whether field treatments have had an effect on the capacity of soil microbes to mineralize PCBS. We have expended considerable effort to validate the fractionation procedure used to assess mineralization and conversion of PCB substrates. The assessment relies on the ability to measure [ 14 C]-labeled CO 2 in the presence of potentially volatile [ 14 C]-labeled PCB and degradation products to differentiate between volatile and non-volatile [ 14 C]-labeled compounds between water-soluble products of metabolism and a mixture of unchanged substrate and other water-insoluble products and between metabolism and loss or non-extractability of the substrate

An assessment of PCB degradation by microogransims including methods for measuring mineralization

Energy Technology Data Exchange (ETDEWEB)

Hadden, C.; Edenborn, H.; Osborne, T.; Holdsworth, G.; Revis, N.

1990-12-31

These studies sought to isolate and identify organism(s) from PCB contaminated soil and sediment that degrade PCB; to provide information on the potential of organisms in soil samples taken from a PCB-contaminated area to mineralize or dechlorinate PCB congeners; to assess potential enhancement of PCB biodegradation as a result of nutritional amendment of the samples; and to carry out analyses of successive lysimeter samples to determine whether field treatments have had an effect on the capacity of soil microbes to mineralize PCBS. We have expended considerable effort to validate the fractionation procedure used to assess mineralization and conversion of PCB substrates. The assessment relies on the ability to measure [{sup 14}C]-labeled CO{sub 2} in the presence of potentially volatile [{sup 14}C]-labeled PCB and degradation products to differentiate between volatile and non-volatile [{sup 14}C]-labeled compounds between water-soluble products of metabolism and a mixture of unchanged substrate and other water-insoluble products and between metabolism and loss or non-extractability of the substrate.

Ignition and combustion of bulk metals under elevated, normal and reduced gravity conditions

Science.gov (United States)

Abbud-Madrid, Angel; Branch, Melvyn C.; Daily, John W.

1995-01-01

This research effort is aimed at providing further insight into this multi-variable dependent phenomena by looking at the effects of gravity on the ignition and combustion behavior of metals. Since spacecraft are subjected to higher-than-1g gravity loads during launch and reentry and to zero-gravity environments while in orbit, the study of ignition and combustion of bulk metals at different gravitational potentials is of great practical concern. From the scientific standpoint, studies conducted under microgravity conditions provide simplified boundary conditions since buoyancy is removed, and make possible the identification of fundamental ignition mechanisms. The effect of microgravity on the combustion of bulk metals has been investigated by Steinberg, et al. on a drop tower simulator. However, no detailed quantitative work has been done on ignition phenomena of bulk metals at lower or higher-than-normal gravitational fields or on the combustion characteristics of metals at elevated gravity. The primary objective of this investigation is the development of an experimental system capable of providing fundamental physical and chemical information on the ignition of bulk metals under different gravity levels. The metals used in the study, iron (Fe), titanium (Ti), zirconium (Zr), magnesium (Mg), zinc (Zn), and copper (Cu) were selected because of their importance as elements of structural metals and their simple chemical composition (pure metals instead of multi-component alloys to avoid complication in morphology and spectroscopic studies). These samples were also chosen to study the two different combustion modes experienced by metals: heterogeneous or surface oxidation, and homogeneous or gas-phase reaction. The experimental approach provides surface temperature profiles, spectroscopic measurements, surface morphology, x-ray spectrometry of metals specimens and their combustion products, and high-speed cinematography of the heating, ignition and combustion

Bulk-surface relationship of an electronic structure for high-throughput screening of metal oxide catalysts

International Nuclear Information System (INIS)

Kweun, Joshua Minwoo; Li, Chenzhe; Zheng, Yongping; Cho, Maenghyo; Kim, Yoon Young; Cho, Kyeongjae

2016-01-01

Graphical abstract: - Highlights: • Bulk-surface relationship was predicted by the ligand field nature of metal oxides. • Antibonding and bonding d-bands occupancy clarified the bulk-surface relationship. • Different surface relaxations were explained by the bulk electronic structures. • Transition from the bulk to the surface state was simulated by oxygen adsorption. - Abstract: Designing metal-oxides consisting of earth-abundant elements has been a crucial issue to replace precious metal catalysts. To achieve efficient screening of metal-oxide catalysts via bulk descriptors rather than surface descriptors, we investigated the relationship between the electronic structure of bulk and that of the surface for lanthanum-based perovskite oxides, LaMO_3 (M = Ti, V, Cr, Mn, Fe, Co, Ni, Cu). Through density functional theory calculations, we examined the d-band occupancy of the bulk and surface transition-metal atoms (n_B_u_l_k and n_S_u_r_f) and the adsorption energy of an oxygen atom (E_a_d_s) on (001), (110), and (111) surfaces. For the (001) surface, we observed strong correlation between the n_B_u_l_k and n_S_u_r_f with an R-squared value over 94%, and the result was interpreted in terms of ligand field splitting and antibonding/bonding level splitting. Moreover, the E_a_d_s on the surfaces was highly correlated with the n_B_u_l_k with an R-squared value of more than 94%, and different surface relaxations could be explained by the bulk electronic structure (e.g., LaMnO_3 vs. LaTiO_3). These results suggest that a bulk-derived descriptor such as n_B_u_l_k can be used to screen metal-oxide catalysts.

A route to transparent bulk metals

KAUST Repository

Schwingenschlögl, Udo

2012-07-23

Hypothetical compounds based on a sapphire host are investigated with respect to their structural as well as electronic features. The results are obtained by electronic structure calculations within density functional theory and the generalized gradient approximation. A quarter of the Al atoms in Al 2O 3 is replaced by a 4d transition metal M ion, with d 0 to d 9 electronic configuration. We perform structure optimizations for all the compounds and analyze the electronic states. Due to the sizeable band gap of the Al 2O 3 host, we can identify promising candidates for transparent bulk metals. We explain the mechanisms leading to this combination of materials properties. © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Mechanical improvement of metal reinforcement rings for a finite ring-shaped superconducting bulk

Science.gov (United States)

Huang, Chen-Guang; Zhou, You-He

2018-03-01

As a key technique, reinforcement of type-II superconducting bulks with metal rings can efficiently improve their mechanical properties to enhance the maximum trapped field. In this paper, we study the magnetostrictive and fracture behaviors of a finite superconducting ring bulk reinforced by three typical reinforcing structures composed of metal rings during the magnetizing process by means of the minimization of magnetic energy and the finite element method. After a field-dependent critical current density is adopted, the magnetostriction, pinning-induced stress, and crack tip stress intensity factor are calculated considering the demagnetization effects. The results show that the mechanical properties of the ring bulk are strongly dependent on the reinforcing structure and the material and geometrical parameters of the metal rings. Introducing the metal ring can significantly reduce the hoop stress, and the reduction effect by internal reinforcement is much improved relative to external reinforcement. By comparison, bilateral reinforcement seems to be the best candidate structure. Only when the metal rings have particular Young's modulus and radial thickness will they contribute to improve the mechanical properties the most. In addition, if an edge crack is pre-existing in the ring bulk, the presence of metal rings can effectively avoid crack propagation since it reduces the crack tip stress intensity factor by nearly one order of magnitude.

Carcinogenicity/tumour promotion by NDL PCB

Energy Technology Data Exchange (ETDEWEB)

Schrenk, D. [Kaiserslautern Univ. (Germany). Food Chemistry and Environmental Toxicology

2004-09-15

Polychlorinated biphenyls (PCBs) belong to the group of persistent environmental pollutants exhibiting neurotoxic, teratogenic and tumour-promoting effects in experimental animal models. PCB congeners can be divided into 'dioxinlike' and 'non-dioxinlike' congeners on the basis of their ability to act as aryl hydrocarbon receptor (AhR) agonists. Like the most toxic dioxin congener 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD) 'dioxinlike' PCBs bind to the AhR and show characteristic effects on the expression of AhR-regulated genes including the induction of cytochrome P450 (CYP) 1A1. On the other hand, 'non-dioxinlike' PCB congeners have a lower or no binding affinity to the AhR, but exhibit a 'phenobarbital-type' induction of CYP 2B1/2 activity. A carcinogenic potential of PCBs has been demonstrated with technical mixtures such as Aroclors or Clophens. In these studies the liver and the thyroid gland were found to be the principal target organs of PCB-mediated carcinogenesis in rodents. No studies have been published, however, on the carcinogenicity of individual congeners. In two-stage initiation-promotion protocols in rats, both technical mixtures and individual 'dioxinlike' and 'non-dioxinlike' congeners were reported to act as liver tumour promoters.

Differences in energy expenditures and growth dilution explain higher PCB concentrations in male summer flounder

Science.gov (United States)

Madenjian, Charles P.; Jensen, Olaf P.; Rediske, Richard R.; O'Keefe, James P.; Vastano, Anthony R.; Pothoven, Steven A.

2016-01-01

Comparison of polychlorinated biphenyl (PCB) concentrations between the sexes of mature fish may reveal important behavioral and physiological differences between the sexes. We determined whole-fish PCB concentrations in 23 female summer flounder Paralichthys dentatus and 27 male summer flounder from New Jersey coastal waters. To investigate the potential for differences in diet or habitat utilization between the sexes, carbon and nitrogen stable isotope ratios were also determined. In 5 of the 23 female summer flounder, PCB concentrations in the somatic tissue and ovaries were determined. In addition, we used bioenergetics modeling to assess the contribution of the growth dilution effect to the observed difference in PCB concentrations between the sexes. Whole-fish PCB concentrations for females and males averaged 87 and 124 ng/g, respectively; thus males were 43% higher in PCB concentration compared with females. Carbon and nitrogen stable isotope ratios did not significantly differ between the sexes, suggesting that diet composition and habitat utilization did not vary between the sexes. Based on PCB determinations in the somatic tissue and ovaries, we predicted that PCB concentration of females would increase by 0.6%, on average, immediately after spawning due to release of eggs. Thus, the change in PCB concentration due to release of eggs did not explain the higher PCB concentrations observed in males. Bioenergetics modeling results indicated that the growth dilution effect could account for males being 19% higher in PCB concentration compared with females. Thus, the bulk of the observed difference in PCB concentrations between the sexes was not explained by growth dilution. We concluded that a higher rate of energy expenditure in males, stemming from greater activity and a greater resting metabolic rate, was most likely the primary driver for the observed difference in PCB concentrations between the sexes.

Differences in Energy Expenditures and Growth Dilution Explain Higher PCB Concentrations in Male Summer Flounder.

Directory of Open Access Journals (Sweden)

Charles P Madenjian

Full Text Available Comparison of polychlorinated biphenyl (PCB concentrations between the sexes of mature fish may reveal important behavioral and physiological differences between the sexes. We determined whole-fish PCB concentrations in 23 female summer flounder Paralichthys dentatus and 27 male summer flounder from New Jersey coastal waters. To investigate the potential for differences in diet or habitat utilization between the sexes, carbon and nitrogen stable isotope ratios were also determined. In 5 of the 23 female summer flounder, PCB concentrations in the somatic tissue and ovaries were determined. In addition, we used bioenergetics modeling to assess the contribution of the growth dilution effect to the observed difference in PCB concentrations between the sexes. Whole-fish PCB concentrations for females and males averaged 87 and 124 ng/g, respectively; thus males were 43% higher in PCB concentration compared with females. Carbon and nitrogen stable isotope ratios did not significantly differ between the sexes, suggesting that diet composition and habitat utilization did not vary between the sexes. Based on PCB determinations in the somatic tissue and ovaries, we predicted that PCB concentration of females would increase by 0.6%, on average, immediately after spawning due to release of eggs. Thus, the change in PCB concentration due to release of eggs did not explain the higher PCB concentrations observed in males. Bioenergetics modeling results indicated that the growth dilution effect could account for males being 19% higher in PCB concentration compared with females. Thus, the bulk of the observed difference in PCB concentrations between the sexes was not explained by growth dilution. We concluded that a higher rate of energy expenditure in males, stemming from greater activity and a greater resting metabolic rate, was most likely the primary driver for the observed difference in PCB concentrations between the sexes.

Trace metals in bulk precipitation and throughfall in a suburban area of Japan

Science.gov (United States)

Hou, H.; Takamatsu, T.; Koshikawa, M. K.; Hosomi, M.

Throughfall and bulk precipitation samples were collected monthly for 1.5 years over bare land and under canopies of Japanese cedar ( Cryptomeria japonica), Japanese red pine ( Pinus densiflora), Japanese cypress ( Chamaecyparis obtusa), and bamboo-leafed oak ( Quercus myrsinaefolia) in a suburban area of Japan. Samples were analyzed for dissolved Al, Mn, Fe, Cu, Zn, Ag, In, Sn, Sb and Bi by ICP-AES and ICP-MS. The metal concentrations were higher in throughfall, especially that of C. japonica, than bulk precipitation. Enrichment ratios (ERs: ratios of metal concentrations in throughfall to those in bulk precipitation) ranged from 2.5 (Zn) to 5.3 (Ag) (3.9 on average), and ERs for slightly soluble metals were generally higher than those for easily soluble metals. Concentrations of Mn, Fe, Cu, and Zn accounted for 99% of the total concentration of heavy metals in rainwater, whereas those of rare metals such as Ag, In, Sn, and Bi totaled rare metals were 0.002 and 0.010 μg l -1 for Ag, 0.001 and 0.005 μg l -1 for In, 0.062 and 0.21 μg l -1 for Sn, and 0.006 and 0.023 μg l -1 for Bi in bulk precipitation and throughfall, respectively. The metal concentrations in rainwater were negatively correlated to the volume of rainwater, indicating that washout is the main mechanism that incorporates metals into rainwater. From the enrichment factors, that is, (X/Al) rain/(X/Al) crust, metals other than Fe were shown to be more enriched in rainwater than in the Earth's crust, including those present as a result of leaching from soil dust (Mn) and from anthropogenic sources (Cu, Zn, Ag, In, Sn, Sb, and Bi).

Diffuse emissions of PCDD/F and dioxin-like PCB from industrial sources in the Flemish region (Belgium)

Energy Technology Data Exchange (ETDEWEB)

Francois, F.; Blondeel, M.; Bernaert, P.; Baert, R. [Ministry of the Flemish Community - Environmental Inspection Section, Brussels (Belgium)

2004-09-15

In Belgium, and especially in the Flemish region, the contamination of the environment and food chain with PCDD/F and PCB has been a major public concern during the past decade. The largest point sources of PCDD/F emissions have been monitored and tackled by the Environment Inspection Section (EIS) since 1993. This has caused a very significant emission reduction, which in its turn had a considerable impact on lowering the environmental and food PCDD/F levels, both in the immediate surroundings of the sources and on a regional scale. However, at a few measurement locations, levels of PCDD/F in deposition samples and in cow's milk remained increased despite the stack emission reduction of nearby sources. Recently, also increased dioxinlike PCB levels were found at some locations. This has led to an investigation of the contribution of diffuse emission sources, revealing the importance of such sources at particular plants, mainly in the non-ferrous metal and scrap metal sectors.

Elastic properties of superconducting bulk metallic glasses

International Nuclear Information System (INIS)

Hempel, Marius

2015-01-01

Within the framework of this thesis the elastic properties of a superconducting bulk metallic glass between 10 mK and 300 K were first investigated. In order to measure the entire temperature range, in particular the low temperature part, new experimental techniques were developed. Using an inductive readout scheme for a double paddle oscillator it was possible to determine the internal friction and the relative change of sound velocity of bulk metallic glasses with high precision. This allowed for a detailed comparison of the data with different models. The analysis focuses on the low temperature regime where the properties of glassy materials are governed by atomic tunneling systems as described by the tunneling model. The influence of conduction electrons in the normal conducting state and quasiparticles in the superconducting state of the glass were accounted for in the theoretical description, resulting in a good agreement over a large temperature range between measured data and prediction of the tunneling model. This allowed for a direct determination of the coupling constant between electrons and tunneling systems. In the vicinity of the transition temperature Tc the data can only be described if a modified distribution function of the tunneling parameters is applied.

Electron beam welding of the dissimilar Zr-based bulk metallic glass and Ti metal

Energy Technology Data Exchange (ETDEWEB)

Kim, Jonghyun [Department of Material Science, Kumamoto University, Kumamoto 860-8555 (Japan)], E-mail: joindoc@kumamoto-u.ac.jp; Kawamura, Y. [Department of Material Science, Kumamoto University, Kumamoto 860-8555 (Japan)

2007-04-15

We successfully welded 3 mm thick Zr{sub 41}Be{sub 23}Ti{sub 14}Cu{sub 12}Ni{sub 10} bulk metallic glass plate to Ti metal by electron beam welding with a beam irradiated 0.4 mm on the BMG side of the interface. There was no crystallization or defects in the weld because changes in the chemical composition of the weld metal were prevented. Bending showed that the welded sample had a higher strength than the Ti base metal. The interface had a 10 {mu}m thick interdiffusion layer of Zr and Ti.

An interatomic potential for studying CuZr bulk metallic glasses

DEFF Research Database (Denmark)

Paduraru, Anca; Kenoufi, Abdel; Bailey, Nicholas

2007-01-01

-scale deformation events and may furthermore involve localization through formation of shear bands. In this paper, an Effective Medium Theory (EMT) potential optimized for modeling the mechanical and thermodynamic properties of CuZr bulk metallic glass is studied. The late transition metals crystallizing in close......The mechanical properties of BMGs are remarkably different from the ones of ordinary metallic alloys due to the atomic level disorder in the glassy state. Unlike crystalline materials plastic deformation in metallic glasses cannot be caused by lattice defects but takes place through atomic...

Serum PCB levels and congener profiles among teachers in PCB-containing schools: a pilot study

Science.gov (United States)

2011-01-01

Background PCB contamination in the built environment may result from the release of PCBs from building materials. The significance of this contamination as a pathway of human exposure is not well-characterized, however. This research compared the serum PCB concentrations, and congener profiles between 18 teachers in PCB-containing schools and referent populations. Methods Blood samples from 18 teachers in PCB-containing schools were analyzed for 57 PCB congeners. Serum PCB concentrations and congener patterns were compared between the teachers, to the 2003-4 NHANES (National Health and Nutrition Examination Survey) data, and to data from 358 Greater Boston area men. Results Teachers at one school had higher levels of lighter (PCB 6-74) congeners compared to teachers from other schools. PCB congener 47 contributed substantially to these elevated levels. Older teachers (ages 50-64) from all schools had higher total (sum of 33 congeners) serum PCB concentrations than age-comparable NHANES reference values. Comparing the teachers to the referent population of men from the Greater Boston area (all under age 51), no difference in total serum PCB levels was observed between the referents and teachers up to 50 years age. However, the teachers had significantly elevated serum concentrations of lighter congeners (PCB 6-74). This difference was confirmed by comparing the congener-specific ratios between groups, and principal component analysis showed that the relative contribution of lighter congeners differed between the teachers and the referents. Conclusions These findings suggest that the teachers in the PCB-containing buildings had higher serum levels of lighter PCB congeners (PCB 6-74) than the referent populations. Examination of the patterns, as well as concentrations of individual PCB congeners in serum is essential to investigating the contributions from potential environmental sources of PCB exposure. PMID:21668970

Dioxin-like (PCB 126) and non dioxin-like (PCB 153) action on DNA damage and apoptosis in granulosa cells. Preliminary data

Energy Technology Data Exchange (ETDEWEB)

Gregoraszczuk, E.L.; Wojtowicz, A. [Lab. of Physiology and Toxicology of Reproduction, Inst. of Zoology, Jagiellonian Univ., Krakow (Poland); Kapiszewska, M.; Magnowska, Z. [Dept. of General Biochemistry, Jagiellonian Univ., Krakow (Poland)

2004-09-15

Introduction Approximately 60-90% of all cancer cases are now generally believed to be due to environmental factors, to which humans are exposed by taking food, and water or inhaling air. These chemicals, including polycyclic aromatic hydrocarbons (PAHs), can be subdivided into different classes. TCDD was classified as group (documented carcinogen in humans) Benzo [a] pyrene and benzo [a] anthracene were included into group 2A (probably carcinogen in humans). PCB is not mentioned in this list. The International Agency for Research on Cancer (IARC) maintains a register of human carcinogens and suspected human carcinogens. The capacity of PCBs to induce DNA strand breaks has been studied to a lesser degree and is quite controversial. DNA strand breaks are the potentially mutagenic lesions that have been proposed as a genotoxicity biomarker for the biomonitoring of environmental pollutants. The mutations induced by these lesions in pollutant-exposed populations are believed to be induced by chemical carcinogens. The formation of PCB adducts has been demonstrated and measured in vitro and in vivo 3. The capacity of PCBs to form DNA adducts depends on their metabolic rate, which is determined by the degree of chlorination. The aim of the presented preliminary data was to evaluate the follicular stage-specific action of PCB 126 and PCB 153 on DNA damage and apoptosis in granulosa cells.

Biological remediation of polychlorinated biphenyls (PCB) in the ...

African Journals Online (AJOL)

ajl yemi

2011-12-19

Dec 19, 2011 ... This widespread contamination of air, soil and water by metals, chemicals and metalloids causes environmental concerns, ... basic structure of PCB according to Wiegel and Wu. (2000), is as shown in Figure. 1. ..... inability to understand the interaction between complex chemicals in addition to physical and ...

High performance bulk metallic glass/carbon nanotube composite cathodes for electron field emission

International Nuclear Information System (INIS)

Hojati-Talemi, Pejman; Gibson, Mark A.; East, Daniel; Simon, George P.

2011-01-01

We report the preparation of new nanocomposites based on a combination of bulk metallic glass and carbon nanotubes for electron field emission applications. The use of bulk metallic glass as the matrix ensures high electrical and thermal conductivity, high thermal stability, and ease of processing, whilst the well dispersed carbon nanotubes act as highly efficient electron emitters. These advantages, alongside excellent electron emission properties, make these composites one of the best reported options for electron emission applications to date.

High performance bulk metallic glass/carbon nanotube composite cathodes for electron field emission

Energy Technology Data Exchange (ETDEWEB)

Hojati-Talemi, Pejman [Department of Materials Engineering, Monash University, Clayton, Vic 3800 (Australia); Mawson Institute, University of South Australia, Mawson Lakes, SA 5095 (Australia); Gibson, Mark A. [Process Science and Engineering, Commonwealth Scientific and Industrial Research Organisation, Clayton, Vic 3168 (Australia); East, Daniel; Simon, George P. [Department of Materials Engineering, Monash University, Clayton, Vic 3800 (Australia)

2011-11-07

We report the preparation of new nanocomposites based on a combination of bulk metallic glass and carbon nanotubes for electron field emission applications. The use of bulk metallic glass as the matrix ensures high electrical and thermal conductivity, high thermal stability, and ease of processing, whilst the well dispersed carbon nanotubes act as highly efficient electron emitters. These advantages, alongside excellent electron emission properties, make these composites one of the best reported options for electron emission applications to date.

PCB138, but not PCB153 and PCB180, acts as a weak antiandrogen in vitro

DEFF Research Database (Denmark)

Vinggaard, A.M.; Bonefeld-Jørgensen, Eva Cecilie

2000-01-01

The polychlorinated biphenyls (PCBs) constitute a group of persistent environmental chemicals including 209 possible congeners exhibiting a variety of chlorine substitution patterns. Due to their lipophilic nature and resistance toward biotransformation, PCBs accumulate in the food chain and all...... environmental matrixes including human adipose tissue, blood and milk. In most biological extracts PCB#138 (2,2',3,4,4',5-hexaCB), PCB#153 (2,2',4,4',5,5'-hexaCB), and PCB#180 (2,2',3,4,4',5,5'-heptaCB) are the dominating components. Depending on the position and number of chlorine substitutions, different...... classes of PCB congeners elicit a complex spectrum of biological and toxic responses in in vivo and in vitro models. Some PCBs exert dioxin-like activities mediated through the aryl hydrocarbon receptor (Ah receptor) giving rise to health risk such as organ toxicity and carcinogenesis. Although reports...

Criticality in Bulk Metallic Glass Constituent Elements

Science.gov (United States)

Mota, Rodrigo Miguel Ojeda; Graedel, T. E.; Pekarskaya, Evgenia; Schroers, Jan

2017-11-01

Bulk metallic glasses (BMGs), which readily form amorphous phases during solidification, are increasingly being used in first applications of watch components, electronic casings, and sporting goods. The compositions of BMGs typically include four to six elements. Various political and geological factors have recently led to supply disruptions for several metals, including some present in BMG compositions. In this work, we assess the "criticality" of 22 technologically interesting BMG compositions, compare the results with those for three common engineering alloy groups, and derive recommendations for BMG composition choices from a criticality perspective. The criticality of BMGs is found to be generally much higher compared with those for the established engineering alloys. Therefore, criticality concerns should also be considered in the choice between existing and developing novel BMGs.

The Engineering Of PCB Processing Machine

International Nuclear Information System (INIS)

Handoyo, Demon; Satmoko, Ari; T, Sapta; Heru, G. B.

2001-01-01

The engineering of PCB processing machine had been done. Purposes of the engineering of PCB processing machine are used to process PCB and to get the data's of characteristic of PCB processing. Further, these data's will be used as setting point when processing of PCB is done with manual and automatic control. The method of processing of PCB are inserting and pulling of the PCB rack to and from Ferro chlorite using electrical motor to corrosive Cu shield parts witch is not used. The experiment have result that the characteristic of operation of PCB processing machine as we hope when designing

Microstructural characterization of Mg-based bulk metallic glass and nanocomposite

Energy Technology Data Exchange (ETDEWEB)

Babilas, Rafał, E-mail: rafal.babilas@polsl.pl [Institute of Engineering Materials and Biomaterials, Silesian University of Technology, Konarskiego 18a St., 44-100 Gliwice (Poland); Nowosielski, Ryszard; Pawlyta, Mirosława [Institute of Engineering Materials and Biomaterials, Silesian University of Technology, Konarskiego 18a St., 44-100 Gliwice (Poland); Fitch, Andy [European Synchrotron Radiation Facility, CS40220, 38043 Grenoble (France); Burian, Andrzej [A. Chelkowski Institute of Physics, University of Silesia, Uniwersytecka 4 St., 40-007 Katowice (Poland)

2015-04-15

New magnesium-based bulk metallic glasses Mg{sub 60}Cu{sub 30}Y{sub 10} have been prepared by pressure casting. Glassy alloys were successfully annealed to become nanocomposite containing 200 nm crystallites in an amorphous matrix. The microstructure of bulk glassy alloy and nanocomposite obtained during heat treatment was examined by X-ray diffraction and scanning and high-resolution electron microscopy. Metallic glass has been also studied to explain the structural characteristics by the reverse Monte Carlo (RMC) modeling based on the diffraction data. The HRTEM images allow to indicate some medium-range order (MRO) regions about 2–3 nm in size and formation of local atomic clusters. The RMC modeling results confirmed some kinds of short range order (SRO) structures. It was found that the structure of bulk metallic glass formed by the pressure casting is homogeneous. The composite material contained very small particles in the amorphous matrix. Homogeneous glassy alloy had better corrosion resistance than a composite containing nanocrystalline particles in a glassy matrix. - Highlights: • RMC modeling demonstrates some kinds of SRO structures in Mg-based BMGs. • HRTEM indicated MRO regions about 2–3 nm and SRO regions about 0.5 nm in size. • Mg-based glassy alloys were successfully annealed to become nanocomposite material. • Crystalline particles have spherical morphology with an average diameter of 200 nm. • Glassy alloy had higher corrosion resistance than a nanocomposite sample.

Bulk glass formation and crystallization in zirconium based bulk metallic glass forming alloys

International Nuclear Information System (INIS)

Savalia, R.T.; Neogy, S.; Dey, G.K.; Banerjee, S.

2002-01-01

The microstructures of Zr based metallic glasses produced in bulk form have been described in the as-cast condition and after crystallization. Various microscopic techniques have been used to characterize the microstructures. The microstructure in the as-cast condition was found to contain isolated crystals and crystalline aggregates embedded in the amorphous matrix. Quenched-in nuclei of crystalline phases were found to be present in fully amorphous regions. These glasses after crystallization gave rise to nanocrystalline solids. (author)

Thermal behaviors of liquid La-based bulk metallic glasses

Energy Technology Data Exchange (ETDEWEB)

Zhang, D. W.; Wang, X. D., E-mail: wangxd@zju.edu.cn, E-mail: jiangjz@zju.edu.cn; Lou, H. B.; Cao, Q. P.; Jiang, J. Z., E-mail: wangxd@zju.edu.cn, E-mail: jiangjz@zju.edu.cn [International Center for New-Structured Materials (ICNSM), Laboratory of New-Structured Materials, State Key Laboratory of Silicon Materials, and Department of Materials Science and Engineering, Zhejiang University, Hangzhou 310027 (China); Wang, L. W. [Institute of Materials Science and Engineering, Lanzhou University, Lanzhou 730000 (China); Zhang, D. X. [State Key Laboratory of Modern Optical Instrumentation, Zhejiang University, Hangzhou 310027 (China)

2014-12-14

Thermal behaviors of liquid La-based bulk metallic glasses have been measured by using the dilatometer with a self-sealed sample cell. It is demonstrated that the strong glass forming liquid not only has the small thermal expansion coefficient but also shows the slow variation rate. Moreover, the strong glass former has relatively dense atomic packing and also small density change in the liquid state. The results suggest that the high glass forming ability of La-based metallic glasses would be closely related to the slow atomic rearrangements in liquid melts.

An Investigation into the Non-bulk Rail Freight Transport in Australia

Directory of Open Access Journals (Sweden)

Hadi Ghaderi

2015-03-01

Full Text Available In the last decade freight transport has gained further momentum in Australia, partly through significant demand growth at both domestic and international levels and partly as the result of Australia's long term need for infrastructure decision making. Amongst the freight task, non-bulk freight is the fastest growing freight task in Australia and is forecast to grow much faster than the rate of population growth and the average national GDP growth. However, rail's share in the non-bulk market has declined significantly in the last four decades. This study therefore provides an insight into the efficiency and operational management issues facing by the Australian non-bulk rail sector by focusing on three areas; the level of track compatibility and the relevant operational issues, the demographics of non-bulk freight in Australia and the current status of intermodal terminals in relation to rail connectivity and location. As the result, a more detailed understanding of the current shortages in the Australian non-bulk rail freight sector is achieved and managerial implications are provided.

Physical factors controlling the ductility of bulk metallic glasses

Energy Technology Data Exchange (ETDEWEB)

Liu, Y. [Central South University, China; Liu, Chain T [ORNL; Zhang, Z. [University of Tennessee, Knoxville (UTK); Keppens, V. [University of Tennessee, Knoxville (UTK)

2008-01-01

In order to identify key physical factor controlling the deformation and fracture behavior of bulk metallic glasses (BMGs), we compiled and analyzed the elastic moduli and compressive ductility for BMGs. In addition, new modulus data were generated in the critical ranges in order to facilitate the analysis. We have found that the intrinsic ductility of BMGs can be correlated with the bulk-to-shear modulus ratio B/G according to Pugh's [Philos. Mag. 45, 823 (1954) ] rule. In some individual BMG systems, for example, Fe based, the relationship seems to be very clear. The physical meaning of this correlation is discussed in terms of atomic bonding and connectivity.

In-situ ductile metal/bulk metallic glass matrix composites formed by chemical partitioning

Science.gov (United States)

Kim, Choong Paul; Hays, Charles C.; Johnson, William L.

2004-03-23

A composite metal object comprises ductile crystalline metal particles in an amorphous metal matrix. An alloy is heated above its liquidus temperature. Upon cooling from the high temperature melt, the alloy chemically partitions, forming dendrites in the melt. Upon cooling the remaining liquid below the glass transition temperature it freezes to the amorphous state, producing a two-phase microstructure containing crystalline particles in an amorphous metal matrix. The ductile metal particles have a size in the range of from 0.1 to 15 micrometers and spacing in the range of from 0.1 to 20 micrometers. Preferably, the particle size is in the range of from 0.5 to 8 micrometers and spacing is in the range of from 1 to 10 micrometers. The volume proportion of particles is in the range of from 5 to 50% and preferably 15 to 35%. Differential cooling can produce oriented dendrites of ductile metal phase in an amorphous matrix. Examples are given in the Zr--Ti--Cu--Ni--Be alloy bulk glass forming system with added niobium.

Residual stresses in a bulk metallic glass-stainless steel composite

Energy Technology Data Exchange (ETDEWEB)

Aydiner, C.C. [Department of Materials and Science Engineering, Iowa State University, Ames, IA 50011 (United States); Uestuendag, E. [Department of Materials and Science Engineering, Iowa State University, Ames, IA 50011 (United States)]. E-mail: ustundag@iastate.edu; Clausen, B. [Lujan Neutron Science Center, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Hanan, J.C. [Division of Engineering and Applied Science, California Institute of Technology, Pasadena, CA 91125 (United States); Winholtz, R.A. [Department of Mechanical and Aerospace Engineering and Research Reactor Center, University of Missouri, Columbia, MO 65211 (United States); Bourke, M.A.M. [Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Peker, A. [Liquidmetal Technologies, Lake Forest, CA 92630 (United States)

2005-06-15

Bulk metallic glasses (BMGs) are new structural materials with impressive mechanical properties. They can now be cast into large dimensions, which can lead to significant residual stress generation due to thermal tempering. In this process, a surface compression develops balanced with tension in the interior. To evaluate this phenomenon non-destructively, a model cylindrical stainless steel (SS)-BMG composite was prepared and studied using neutron diffraction and finite element (FE) modeling. The residual strain data from the SS obtained by diffraction were used in modeling calculations to show that significant tempering could be achieved in the composite (about -200 MPa surface compression in the SS). The strong bond between the SS and BMG allowed efficient load transfer and facilitated stress generation. The final values of the residual stresses were seen to be relatively insensitive to the high temperature constitutive behavior of the SS due to the physics of the thermal tempering in BMGs. The approach presented here constitutes an effective means to study non-destructively thermal tempering in BMGs.

Residual stresses in a bulk metallic glass-stainless steel composite

International Nuclear Information System (INIS)

Aydiner, C.C.; Uestuendag, E.; Clausen, B.; Hanan, J.C.; Winholtz, R.A.; Bourke, M.A.M.; Peker, A.

2005-01-01

Bulk metallic glasses (BMGs) are new structural materials with impressive mechanical properties. They can now be cast into large dimensions, which can lead to significant residual stress generation due to thermal tempering. In this process, a surface compression develops balanced with tension in the interior. To evaluate this phenomenon non-destructively, a model cylindrical stainless steel (SS)-BMG composite was prepared and studied using neutron diffraction and finite element (FE) modeling. The residual strain data from the SS obtained by diffraction were used in modeling calculations to show that significant tempering could be achieved in the composite (about -200 MPa surface compression in the SS). The strong bond between the SS and BMG allowed efficient load transfer and facilitated stress generation. The final values of the residual stresses were seen to be relatively insensitive to the high temperature constitutive behavior of the SS due to the physics of the thermal tempering in BMGs. The approach presented here constitutes an effective means to study non-destructively thermal tempering in BMGs

Postnatal exposure to PCB 153 and PCB 180, but not to PCB 52, produces changes in activity level and stimulus control in outbred male Wistar Kyoto rats

Directory of Open Access Journals (Sweden)

Walaas S

2011-05-01

Full Text Available Abstract Background Polychlorinated biphenyls (PCBs are a class of organic compounds that bioaccumulate due to their chemical stability and lipophilic properties. Humans are prenatally exposed via trans-placental transfer, through breast milk as infants, and through fish, seafood and fatty foods as adolescents and adults. Exposure has several reported effects ranging from developmental abnormalities to cognitive and motor deficiencies. In the present study, three experimental groups of rats were orally exposed to PCBs typically found in human breast milk and then behaviorally tested for changes in measures of stimulus control (percentage lever-presses on the reinforcer-producing lever, activity level (responses with IRTs > 0.67 s, and responses with short IRTs ( Methods Male offspring from Wistar Kyoto (WKY/NTac dams purchased pregnant from Taconic Farms (Germantown, NY were orally given PCB at around postnatal day 8, 14, and 20 at a dose of 10 mg/kg body weight at each exposure. Three experimental groups were exposed either to PCB 52, PCB 153, or PCB 180. A fourth group fed corn oil only served as controls. From postnatal day 25, for 33 days, the animals were tested for behavioral changes using an operant procedure. Results PCB exposure did not produce behavioral changes during training when responding was frequently reinforced using a variable interval 3 s schedule. When correct responses were reinforced on a variable interval 180 s schedule, animals exposed to PCB 153 or PCB 180 were less active than controls and animals exposed to PCB 52. Stimulus control was better in animals exposed to PCB 180 than in controls and in the PCB 52 group. Also, the PCB 153 and PCB 180 groups had fewer responses with short IRTs than the PCB 52 group. No effects of exposure to PCB 52 were found when compared to controls. Conclusions Exposure to PCBs 153 and 180 produced hypoactivity that continued at least five weeks after the last exposure. No effects of

Low temperature incineration of mixed wastes using bulk metal oxide catalysts

International Nuclear Information System (INIS)

Gordon, M.J.; Gaur, S.; Kelkar, S.; Baldwin, R.M.

1996-01-01

Volume reduction of low-level mixed wastes from former nuclear weapons facilities is a significant environmental problem. Processing of these materials presents unique scientific and engineering problems due to the presence of minute quantities of radionuclides which must be contained and concentrated for later safe disposal. Low-temperature catalytic incineration is one option that has been utilized at the Rocky Flats facility for this purpose. This paper presents results of research regarding evaluation of bulk metal oxides as catalysts for low-temperature incineration of carbonaceous residues which are typical by-products of fluidized bed combustion of mixed wastes under oxygen-lean conditions. A series of 14 metal oxides were screened in a thermogravimetric analyzer, using on-line mass spectrometry for speciation of reaction product gases. Catalyst evaluation criteria focused on the thermal-redox activity of the metals using both carbon black and PVC char as surrogate waste materials. Results indicated that metal oxides which were P-type semiconductor materials were suitable as catalysts for this application. Oxides of cobalt, molybdenum, vanadium, and manganese were found to be particularly stable and active catalysts under conditions specific to this process (T<650C, low oxygen partial pressures). Bench-scale evaluation of these metal oxides with respect to stability to chlorine (HCl) attack was carried out at 550C using a TG/MS system. Cobalt oxide was found to be resistant to metal loss in a HCl/He gaseous environment while metal loss from Mo, Mn, and V-based catalysts was moderate to severe. XRD and SEM/EDX analysis of spent Co catalysts indicated the formation of non-stoichiometric cobalt chlorides. Regeneration of chlorinated cobalt was found to successfully restore the low-temperature combustion activity to that of the fresh metal oxide

Micromegas in a bulk

International Nuclear Information System (INIS)

Giomataris, I.; De Oliveira, R.; Andriamonje, S.; Aune, S.; Charpak, G.; Colas, P.; Fanourakis, G.; Ferrer, E.; Giganon, A.; Rebourgeard, Ph.; Salin, P.

2006-01-01

In this paper, we present a novel way to manufacture the bulk Micromegas detector. A simple process based on the Printed Circuit Board (PCB) technology is employed to produce the entire sensitive detector. Such a fabrication process could be extended to very large area detectors made by the industry. The low cost fabrication together with the robustness of the electrode materials will make it attractive for several applications ranging from particle physics and astrophysics to medicine

Reliability of lead-free solder joints with different PCB surface finishes under thermal cycling

Energy Technology Data Exchange (ETDEWEB)

Xia Yanghua [State Key Laboratory of Functional Materials for Informatics, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai 200050 (China)], E-mail: xia_yanghua@hotmail.com; Xie Xiaoming [State Key Laboratory of Functional Materials for Informatics, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai 200050 (China)

2008-04-24

The reliability of lead-free electronic assemblies under thermal cycling was investigated. Thin small outline package (TSOP) devices with FeNi leads were reflow soldered on FR4 PCB (printed circuit board) with Sn3.0Ag0.5Cu (wt%) solder. The effects of different PCB finishes (organic solderability preservative (OSP) and electroless nickel immersion gold (ENIG)) were studied. The results show that OSP finish reveals better performance than its ENIG counterparts. The crack originates at the fringe of heel fillet in both cases. The propagation of crack in the ENIG case is along the device/solder interface, while in the case of OSP, the crack extends parallel to the solder/PCB interface. When the OSP finishes are employed, many Cu6Sn5 precipitates form inside the bulk solder and have a strengthening effect on the solder joint, resulting in better reliability performance as compared to those with ENIG finishes.

Wear behaviour of Zr-based in situ bulk metallic glass matrix ...

Indian Academy of Sciences (India)

based bulk metallic glasses; in situ composites; ductile phase; wear behaviours. 1. Introduction ... crystalline alloys [2], which led to an abnormal phenomenon that the wear ... of BMGs does not follow the empirical Archard's wear equa- tion which ...

Co-exposure to an ortho-substituted PCB (PCB 153) and methylmercury enhances developmental neurotoxic effects

Energy Technology Data Exchange (ETDEWEB)

Fischer, C.; Fredriksson, A.; Eriksson, P. [Dept. Environment. Toxicol., Uppsala Univ. (Sweden)

2004-09-15

In our environment there are innumerable hazardous contaminants. Many of these compounds are the well-known persistent organic pollutants (POPs) like PCB and DDT. Another persistent agent in our environment is methylmercury (MeHg). These agents are known to be neurotoxic in laboratory animals and humans. Fetuses and neonates are known to be high-risk groups for exposure to these agents. A naturally occurring circumstance is the exposure to a combination of different persistent compounds. The knowledge of interaction between different toxic agents during development is sparse. In several studies we have shown that low-dose exposure of environmental toxic agents such as PCBs, DDT, BFRs (brominated flame retardants) as well as well-known neurotoxic agents such as nicotine, organophosphorous compounds and 1-methyl-4-phenyl-1,2,3,6-tetrahydropyridine (MPTP), during the ''BGS'', in neonatal mice can lead to disruption of the adult brain function, and to an increased susceptibility to toxic agents as adults. Our studies concerning developmental neurotoxic effects after neonatal exposure to single PCB congeners have shown that some orthosubstituted PCBs (such as PCB 28, PCB 52, PCB 153) and some co-planar PCBs (such as PCB 77, PCB 126, PCB 169) cause derangement of adult behaviour that can worsen with age. Furthermore, the cholinergic receptors in the brain were also found to be affected8. Just recently we have seen that neonatal co-exposure to an ortho-substituted PCB, 2,2',5,5'-tetrachlorobiphenyl (PCB 52), together with a brominated flame retardant, 2,2',4,4',5-pentabromodiphenylether (PBDE 99), can enhance developmental neurotoxic effects when the exposure occurs during a critical stage of neonatal brain development. The present study was carried out in order to see whether PCB and MeHg could interact to cause enhanced developmental neurotoxic effects on spontaneous behaviour and habituation capability when given to neonatal mice.

Net Shaping of Multifunctional Bulk Metallic Glass Containers and Structures, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Demand for novel manufacturing methods for space systems brings unique properties of bulk metallic glasses (BMG) into the spotlight. In addition to superior...

Thermoplastic forming of bulk metallic glasses for precision robotics components, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Demand for novel manufacturing methods for space systems brings unique properties of bulk metallic glasses (BMG) into the spotlight. In addition to superior...

Wear behaviour of Zr-based in situ bulk metallic glass matrix ...

Indian Academy of Sciences (India)

based bulk metallic glass (BMG) and its in situ BMG matrix composites with diameter of 3 mm were fabricated by conventional Cu-mould casting method and ... The composites showed lower friction coefficient and wear rate than the pure BMG.

Bulk-mediated surface diffusion: non-Markovian desorption dynamics

International Nuclear Information System (INIS)

Revelli, Jorge A; Budde, Carlos E; Prato, Domingo; Wio, Horacio S

2005-01-01

Here we analyse the dynamics of adsorbed molecules within the bulk-mediated surface diffusion framework, when the particle's desorption mechanism is characterized by a non-Markovian process, while the particle's adsorption as well as its motion in the bulk is governed by Markovian dynamics. We study the diffusion of particles in both semi-infinite and finite cubic lattices, analysing the conditional probability to find the system on the reference absorptive plane as well as the surface dispersion as functions of time. The results are compared with known Markovian cases showing the differences that can be exploited to distinguish between Markovian and non-Markovian desorption mechanisms in experimental situations

Friction welding of bulk metallic glasses to different ones

International Nuclear Information System (INIS)

Shoji, Takuo; Kawamura, Yoshihito; Ohno, Yasuhide

2004-01-01

For application of bulk metallic glasses (BMGs) as industrial materials, it is necessary to establish the metallurgical bonding technology. The BMGs exhibit high-strain-rate superplasticity in the supercooled liquid state. It has been reported that bulk metallic glasses were successfully welded together by friction, pulse-current, explosion and electron-beam methods. In this study, friction welding of the BMGs to different ones were tried for Pd 40 Ni 40 P 20 , Pd 40 Cu 30 P 20 Ni 10 , Zr 55 Cu 30 Al 10 Ni 5 and Zr 41 Be 23 Ti 14 Cu 12 Ni 10 BMGs. Successful welding was obtained in the combinations of the Pd 40 Ni 40 P 20 and Pd 40 Cu 30 P 20 Ni 10 BMGs, and the Zr 55 Cu 30 Al 10 Ni 5 and Zr 41 Be 23 Ti 14 Cu 12 Ni 10 ones. No crystallization was observed and no visible defect was recognized in the interface. The joining strength of the welded BMGs was the same as that of the parent BMG or more. BMGs seem to be successfully welded to the different ones with a difference below about 50 K in glass transition temperature

Structural study of conventional and bulk metallic glasses during annealing

International Nuclear Information System (INIS)

Pineda, E.; Hidalgo, I.; Bruna, P.; Pradell, T.; Labrador, A.; Crespo, D.

2009-01-01

Metallic glasses with conventional glass-forming ability (Al-Fe-Nd, Fe-Zr-B, Fe-B-Nb compositions) and bulk metallic glasses (Ca-Mg-Cu compositions) were studied by synchrotron X-ray diffraction during annealing throughout glass transition and crystallization temperatures. The analysis of the first diffraction peak position during the annealing process allowed us to follow the free volume change during relaxation and glass transition. The structure factor and the radial distribution function of the glasses were obtained from the X-ray measurements. The structural changes occurred during annealing are analyzed and discussed.

Distribution of oxides in a Zr-Cu-Ni-Al-Nb-Si bulk metallic glass

Energy Technology Data Exchange (ETDEWEB)

Heinrich, Jochen; Busch, Ralf [Chair of Metallic Materials, Saarland University, PO Box 151150, 66041 Saarbruecken (Germany); Mueller, Frank; Huefner, Stefan [Chair of Experimental Physics, Saarland University, PO Box 151150, 66041 Saarbruecken (Germany)

2010-07-01

The course of oxide presence with distance from the sample surface and bonding partner was studied for the bulk metallic glass with the nominal composition Zr{sub 57.9}Cu{sub 15.4}Ni{sub 12.7}Al{sub 10.2}Nb{sub 2.8}Si{sub 1} (at%) by X-ray photoelectron spectroscopy (XPS). Investigated specimens are taken from vacuum quench-cast rods subjected to oxidation at room temperature and atmosphere. Binding energies were determined in various depths using ion beam ablation of up to 100 nanometers. XPS spectra confirm oxidation primarily of the pure zirconium and aluminum constituents, all other peaks correspond to metallic bonds. While the surface area shows a passivating zirconia layer a few nanometers thick, oxygen is bonded predominantly with aluminum inside the bulk. Since the concentration of oxygen is a crucial factor in the crystallization behavior of bulk metallic glass forming liquids on basis of oxygen affine metals, so far only high purity materials were thought to be suitable. The findings in this study, however, are promising for alloys with industrial grade elements with sufficient glass forming ability. Comparisons of the alloy with differing oxygen content support the conclusion that aluminum acts as an appropriate scavenger for both adsorbed and large amounts of intrinsic oxygen in zirconium based amorphous metals.

Advanced Wear Simulation for Bulk Metal Forming Processes

Directory of Open Access Journals (Sweden)

Behrens Bernd-Arno

2016-01-01

Full Text Available In the recent decades the finite element method has become an essential tool for the cost-efficient virtual process design in the metal forming sector in order to counter the constantly increasing quality standards, particularly from the automotive industry as well as intensified international competition in the forging industry. An optimized process design taking precise tool wear prediction into account is a way to increase the cost-efficiency of the bulk metal forming processes. The main objective of the work presented in this paper is a modelling algorithm, which allows predicting die wear with respect to a geometry update during the forming simulation. Changes in the contact area caused by geometry update lead to the different die wear distribution. It primarily concerns the die areas, which undergo high thermal and mechanical loads.

Compressive yielding of tungsten fiber reinforced bulk metallic glass composites

Energy Technology Data Exchange (ETDEWEB)

Clausen, B.; Lee, S.-Y.; Uestuendag, E.; Aydiner, C.C.; Conner, R.D.; Bourke, M.A.M

2003-07-15

In-situ uniaxial compression tests were conducted on four tungsten fiber reinforced bulk metallic glass matrix composites using neutron diffraction. The results were interpreted with a finite element model. Both phases were seen to approximately obey the von Mises yield criterion. The fibers were observed to yield first and then transfer load to the matrix.

Compressive yielding of tungsten fiber reinforced bulk metallic glass composites

International Nuclear Information System (INIS)

Clausen, B.; Lee, S.-Y.; Uestuendag, E.; Aydiner, C.C.; Conner, R.D.; Bourke, M.A.M.

2003-01-01

In-situ uniaxial compression tests were conducted on four tungsten fiber reinforced bulk metallic glass matrix composites using neutron diffraction. The results were interpreted with a finite element model. Both phases were seen to approximately obey the von Mises yield criterion. The fibers were observed to yield first and then transfer load to the matrix

Analysis of atomic mobility in a Cu38Zr46Ag8Al8 bulk metallic glass

International Nuclear Information System (INIS)

Qiao, J.C.; Pelletier, J.M.

2013-01-01

Highlights: ► Atomic mobility in Cu 38 Zr 46 Ag 8 Al 8 bulk metallic glass have been investigated by DMA. ► Loss factor is directly connected to the energy lost during application of the stress. ► Structural relaxation and crystallization induces a decrease of the atomic mobility. ► The concentration of quasi-point defects links to atomic mobility in metallic glasses. - Abstract: Atomic mobility in as-cast and annealed Cu 38 Zr 46 Ag 8 Al 8 bulk metallic glass samples is analyzed by performing dynamic mechanical analysis. The loss factor is directly connected to the energy lost during application of the stress. Structural relaxation process and crystallization lead to a decrease of the atomic mobility in the bulk metallic glass. A physical model, based on the concept of quasi point defects is introduced, to describe the atomic mobility. Movements in amorphous materials are correlated. The correlation factor χ reflects the atomic mobility in bulk metallic glasses: structural relaxation and crystallization lead to a decrease of χ, implying the reduction of atomic mobility. The evolution of elastic, visco-elastic and viscoplastic components after structural relaxation and partial crystallization state during the mechanical response has been obtained. Compared with as-cast state, structural relaxation induced an increase of elastic component and a decrease of visco-elastic component in the metallic glass.

Automated PCB Inspection System

Directory of Open Access Journals (Sweden)

Syed Usama BUKHARI

2017-05-01

Full Text Available Development of an automated PCB inspection system as per the need of industry is a challenging task. In this paper a case study is presented, to exhibit, a proposed system for an immigration process of a manual PCB inspection system to an automated PCB inspection system, with a minimal intervention on the existing production flow, for a leading automotive manufacturing company. A detailed design of the system, based on computer vision followed by testing and analysis was proposed, in order to aid the manufacturer in the process of automation.

The local structure nature for a Ti-based bulk metallic glass

International Nuclear Information System (INIS)

Chen, Yiqiang; Huang, Yongjiang; Fan, Hongbo; Wang, Dongjun; Shen, Jun

2013-01-01

Highlights: ► The directional bonds in TiZrNiCuBe bulk metallic glass are primarily comprised of Be-Ni and Be-Cu bonds. ► A coefficient η could be extracted from Raman scattering to characterize the glass forming ability. ► The weak directional bonds dependent on Be could increase the localized electrons, facilitating the glass forming ability. - Abstract: In the present work, the local atomic structures of a Be-containing Ti-based bulk metallic glass (BMG) have been characterized using electron spectrum for chemical analysis and Raman scattering, including directional bonds and medium range order. It might suggest that a coefficient could be extracted from Raman scattering to characterize the glass forming ability (GFA), which could be employed to interpret the enhanced GFA by Be addition of Ti-based BMG. Additionally, compared with the crystallized sample, the glassy sample exhibits larger average bond length and larger content of local bond distortion using Raman scattering.

Experimental study on the surface characteristics of Pd-based bulk metallic glass

Energy Technology Data Exchange (ETDEWEB)

Zhang, Xiang; Sun, Bingli [School of Mechanics and Engineering Science, Zhengzhou University, Zhengzhou 450001 (China); National Center for International Joint Research of Micro-nano Molding Technology, Zhengzhou University, Zhengzhou 450001 (China); Key Laboratory for Micro Molding Technology of Henan Province, Zhengzhou University, Zhengzhou, 450001 (China); Zhao, Na [National Center for International Joint Research of Micro-nano Molding Technology, Zhengzhou University, Zhengzhou 450001 (China); Key Laboratory for Micro Molding Technology of Henan Province, Zhengzhou University, Zhengzhou, 450001 (China); National Engineering Research Center for Advanced Polymer Processing Technology, Zhengzhou University, Zhengzhou 450002 (China); Li, Qian, E-mail: qianli@zzu.edu.cn [School of Mechanics and Engineering Science, Zhengzhou University, Zhengzhou 450001 (China); National Center for International Joint Research of Micro-nano Molding Technology, Zhengzhou University, Zhengzhou 450001 (China); Key Laboratory for Micro Molding Technology of Henan Province, Zhengzhou University, Zhengzhou, 450001 (China); National Engineering Research Center for Advanced Polymer Processing Technology, Zhengzhou University, Zhengzhou 450002 (China); Hou, Jianhua; Feng, Weina [School of Mechanics and Engineering Science, Zhengzhou University, Zhengzhou 450001 (China); National Center for International Joint Research of Micro-nano Molding Technology, Zhengzhou University, Zhengzhou 450001 (China); Key Laboratory for Micro Molding Technology of Henan Province, Zhengzhou University, Zhengzhou, 450001 (China)

2014-12-01

Highlights: • Wetting behavior of four polymer melts on Pd-based bulk metallic glass was investigated. • From results, in general, the contact angle of polymer on Pd-based BMG decreases with temperature increasing. • We find a critical temperature for each polymer, above this temperature, contact angle on Pd-based BMG does not decrease with temperature increasing. • Surface free energy of Pd-based BMG was estimated by Owens–Wendt method. - Abstract: The metallic glass has many unique and desirable physical and chemical characteristics for their long-range disordered atomic structure, among them the interfacial properties of the metallic glasses are crucial for their applications and manufacturing. In this work, the contact wetting angles between the polymer melts and Pd{sub 40}Cu{sub 30}Ni{sub 10}P{sub 20} bulk metallic glass (Pd-BMG) with four kinds of roughness were analyzed. Experiments show the order of four polymers wettability on Pd-BMG was PP > HDPE > COC > PC. The surface free energy of Pd-BMG was estimated by Owens–Wendt method using the contact angles of three testing liquids. Neumann method was also used to further evidence the surface free energy of Pd-BMG comparing with PTFE, mold steels NAK80 and LKM2343ESR. The results provide theoretical and technical supports for the fabrication of metallic glass micro mold and the parameter optimization of polymer micro injection molding.

Welding of Zr-based bulk metallic glasses

International Nuclear Information System (INIS)

Elahi, M.

2010-01-01

Recently, many bulk metallic glass (BMG) materials with high specific strength, hardness and superior corrosion resistance have been developed and the maximum thickness of some Zr-based BMGs have reached several tenths of millimeters. Nevertheless, homogeneous glassy BMGs are not thick enough to be used for structural applications. In order to extend the engineering applications of BMG materials, BMG welding technologies needed to be developed. Specifically, the welding technologies of dissimilar materials such as BMG materials to crystalline alloys are to be developed. The functional use of the specific properties of each material in dissimilar material combination provides flexible design possibilities for products. In this project electron beam welding is employed to join BMG with BMG of different composition as well as with different crystalline materials (i.e. Hastealoy C-276, Inconel-625 and pure Ti metal). Defects free weld joint was achieved in BMG-BMG welding. Some cracks were produced in melt zone of BMG-Ti and BMG-Hastealoy C-276 welding while at joint they fuse properly with BMG. Inconel-625 could not properly weld with BMG. In all cases, hardness of melt zone was found to be higher than the base metals and the heat affected zone (HAZ). (author)

Historical reconstruction of polychlorinated biphenyl (PCB) exposures for workers in a capacitor manufacturing plant.

Science.gov (United States)

Hopf, Nancy B; Ruder, Avima M; Waters, Martha A

2014-05-01

We developed a semiquantitative job exposure matrix (JEM) for workers exposed to polychlorinated biphenyls (PCBs) at a capacitor manufacturing plant from 1946 to 1977. In a recently updated mortality study, mortality of prostate and stomach cancer increased with increasing levels of cumulative exposure estimated with this JEM (trend p values = 0.003 and 0.04, respectively). Capacitor manufacturing began with winding bales of foil and paper film, which were placed in a metal capacitor box (pre-assembly), and placed in a vacuum chamber for flood-filling (impregnation) with dielectric fluid (PCBs). Capacitors dripping with PCB residues were then transported to sealing stations where ports were soldered shut before degreasing, leak testing, and painting. Using a systematic approach, all 509 unique jobs identified in the work histories were rated by predetermined process- and plant-specific exposure determinants; then categorized based on the jobs' similarities (combination of exposure determinants) into 35 job exposure categories. The job exposure categories were ranked followed by a qualitative PCB exposure rating (baseline, low, medium, and high) for inhalation and dermal intensity. Category differences in other chemical exposures (solvents, etc.) prevented further combining of categories. The mean of all available PCB concentrations (1975 and 1977) for jobs within each intensity rating was regarded as a representative value for that intensity level. Inhalation (in microgram per cubic milligram) and dermal (unitless) exposures were regarded as equally important. Intensity was frequency adjusted for jobs with continuous or intermittent PCB exposures. Era-modifying factors were applied to the earlier time periods (1946-1974) because exposures were considered to have been greater than in later eras (1975-1977). Such interpolations, extrapolations, and modifying factors may introduce non-differential misclassification; however, we do believe our rigorous method

A guide for validation of FE-Simulations in bulk metal forming

International Nuclear Information System (INIS)

Tekkaya, A. Erman

2005-01-01

Numerical analysis of metal forming processes is an everyday practice in industry. Forming loads, material flow, forming defects such as underfills, laps and even cracks, stresses in dies and punches, as well as product properties like new hardness distribution, dimensional accuracies and residual stresses are predicted by numerical analysis and used for technology generation. Most of the numerical analysis is done by the finite element method made available for engineers and technicians by numerous by powerful commercial software packages. These software packages act as black-boxes and usually hide the complicated numerical procedures and even their crucial parameters from the applier. Therefore, the question arises during the industrial applications: how accurate is the simulation and how can the results can be assessed? The aim of this paper is to provide a guideline to assess the results of metal forming simulations. Although some ideas are valid for any metal forming process, bulk forming is the process concern. The paper will address firstly the possible sources of error in a finite element analysis of bulk forming processes. Then, some useful elementary knowledge will be summarized. Various levels of validation such as result and ability validation and assessment will be discussed. Finally, interpretation of results will be treated. In this content also some suggestions will be given. (author)

Systems and Methods for Implementing Bulk Metallic Glass-Based Strain Wave Gears and Strain Wave Gear Components

Science.gov (United States)

Hofmann, Douglas C. (Inventor); Wilcox, Brian (Inventor)

2016-01-01

Bulk metallic glass-based strain wave gears and strain wave gear components. In one embodiment, a strain wave gear includes: a wave generator; a flexspline that itself includes a first set of gear teeth; and a circular spline that itself includes a second set of gear teeth; where at least one of the wave generator, the flexspline, and the circular spline, includes a bulk metallic glass-based material.

Bulk metal concentrations versus total suspended solids in rivers: Time-invariant & catchment-specific relationships.

Science.gov (United States)

Nasrabadi, Touraj; Ruegner, Hermann; Schwientek, Marc; Bennett, Jeremy; Fazel Valipour, Shahin; Grathwohl, Peter

2018-01-01

Suspended particles in rivers can act as carriers of potentially bioavailable metal species and are thus an emerging area of interest in river system monitoring. The delineation of bulk metals concentrations in river water into dissolved and particulate components is also important for risk assessment. Linear relationships between bulk metal concentrations in water (CW,tot) and total suspended solids (TSS) in water can be used to easily evaluate dissolved (CW, intercept) and particle-bound metal fluxes (CSUS, slope) in streams (CW,tot = CW + CSUS TSS). In this study, we apply this principle to catchments in Iran (Haraz) and Germany (Ammer, Goldersbach, and Steinlach) that show differences in geology, geochemistry, land use and hydrological characteristics. For each catchment, particle-bound and dissolved concentrations for a suite of metals in water were calculated based on linear regressions of total suspended solids and total metal concentrations. Results were replicable across sampling campaigns in different years and seasons (between 2013 and 2016) and could be reproduced in a laboratory sedimentation experiment. CSUS values generally showed little variability in different catchments and agree well with soil background values for some metals (e.g. lead and nickel) while other metals (e.g. copper) indicate anthropogenic influences. CW was elevated in the Haraz (Iran) catchment, indicating higher bioavailability and potential human and ecological health concerns (where higher values of CSUS/CW are considered as a risk indicator).

Study of penetration behavior of PCB-DNAPL in a sand layer by a column experiment.

Science.gov (United States)

Okuda, Nobuyasu; Shimizu, Takaaki; Muratani, Masaru; Terada, Akihiko; Hosomi, Masaaki

2014-11-01

To better understand the infiltration performances of high concentration PCB oils (KC-300 and KC-1000 polychlorinated biphenyl (PCB) mixtures), representative dense non-aqueous phase liquid (DNAPL), under both saturated and unsaturated conditions, we conducted experiments on a sand column filled with Toyoura Standard Sand. When PCB oil with the volume comparable to the total porosity in the column was supplied, the residual PCB concentrations under PCB-water conditions were 4.9×10(4)mgkg(-1) in KC-300 and 3.9×10(4)mgkg(-1) in KC-1000. Under PCB-air conditions, residual PCB concentrations were 6.0×10(4)mgkg(-1) and 2.4×10(5)mgkg(-1) in the upper and lower parts for KC-300 and 3.6×10(4)mgkg(-1) and 1.5×10(5)mgkg(-1) in those for KC-1000, respectively, while the rest of the PCBs were infiltrated. On the other hand, when a small amount of PCB oil with the volume far smaller than the total porosity in the column was supplied, the original PCBs were not transported via water permeation. However, lower-chlorinated PCB congeners-e.g., di- or tri-chlorinated biphenyls-preferentially dissolved and were infiltrated from the bottom of the column. These propensities on PCB oil infiltration can be explained in conjunction with the degree of PCB saturation in the sand column. Copyright © 2014 Elsevier Ltd. All rights reserved.

Composition design and mechanical properties of ternary Cu–Zr–Ti bulk metallic glasses

International Nuclear Information System (INIS)

Pan, Ye; Zeng, Yuqiao; Jing, Lijun; Zhang, Lu; Pi, Jinhong

2014-01-01

Highlights: • Newly designed monolithic bulk metallic glasses are of good glass-forming ability. • Cu 50 Zr 44 Ti 6 exhibits excellent plastic deformation up to ∼7.4%. • Copious and intersected shear bans are observed in the fractography of Cu 50 Zr 44 Ti 6 . • Cu 50 Zr 44 Ti 6 has the best plasticity in the ternary Cu–Zr–Ti bulk metallic glasses. - Abstract: The new compositions of ternary Cu–Zr–Ti bulk metallic glasses are predicted by integrating calculation of vacancy formation energy, mixing enthalpy and configuration entropy of the alloys based on thermodynamics of glass formers. The monolithic amorphous rods of 3 mm diameter have been successfully fabricated, and characterized by X-ray diffractometry, differential scanning calorimetry, scanning electronic microscopy, transmission electronic microscopy and compression tests. The results show that the designed alloys possess good glass forming ability and excellent mechanical properties. The mechanical properties of the samples can be effectively improved by regulating their composition. The monolithic amorphous rod of Cu 50 Zr 44 Ti 6 exhibits a high fracture strength of 1855 MPa and excellent plastic deformation up to ∼7.4%. The formation and propagation of shear bands in samples are also investigated. The enhancement of plastic deformation is mainly contributed to multiplication and intersection of shear bands

Multiple mechanisms of PCB neurotoxicity

Energy Technology Data Exchange (ETDEWEB)

Carpenter, D.O.; Stoner, C.T.; Lawrence, D.A. [Univ. of New York, Albany, NY (United States)] [and others

1996-12-31

Polychlorinated biphenyls (PCBs) have been implicated in cancer, but many of the symptoms in humans exposed to PCBs are related to the nervous system and behavior. We demonstrated three different direct mechanisms whereby PCBs are neurotoxic in rats. By using flow cytometry, we demonstrated that the orthosubstituted PCB congener 2,4,4{prime}, but neither TCDD nor the coplanar PCB congener 3,4,5,3{prime},4{prime}, causes rapid death of cerebellar granule cells. The ortho-substituted congener 2,4,4{prime} reduced long-term potentiation, an indicator of cognitive potential, in hippocampal brain slices, but a similar effect was observed for the coplanar congener 3,4,3{prime},4{prime}, indicating that this effect may be caused by both ortho- and coplanar congeners by mechanisms presumably not mediated via the Ah receptor. It was previously shown that some ortho-substituted PCB congeners cause a reduction in levels of the neurotransmitter dopamine, and we present in vitro and in vivo evidence that this is due to reduction of synthesis of dopamine via inhibition of the enzyme tyrosine hydroxylase. Thus, PCBs have a variety of mechanisms of primary neurotoxicity, and neurotoxicity is a characteristic of ortho-substituted, non-dioxin-like congeners as well as some coplanar congeners. The relative contribution of each of these mechanisms to the loss of cognitive function in humans exposed to PCBs remains to be determined. 42 refs., 3 figs., 1 tab.

Preparation and characterization of Zr-based bulk metallic glasses in form of plate

International Nuclear Information System (INIS)

Pilarczyk, Wirginia

2014-01-01

Highlights: • Zr-based BMGs in form of plate was successful produced by die pressure casting method. • Many techniques have been used to characterize the structure of Zr 55 Cu 30 Ni 5 Al 10 alloy. • The calculated GFA parameters show that the alloy exhibits satisfactory GFA. • The studies reveal that tested as-cast Zr-based alloy is in amorphous state. - Abstract: Zr-based bulk metallic glasses present an interesting combination of physical, chemical and mechanical properties. During the last decade, intensive progress has been made and a number of applications have been suggested for these materials. In order to successfully apply these materials, it is necessary to accurately characterize their structure, thermal stability and other properties accurately. The aim of the presented work is the manufacturing, examination of the structure of selected Zr-based bulk metallic alloys and confirmation of an amorphous structure using X-ray analysis, microscopic observation and thermal analysis. In this work, the Zr-based bulk metallic glasses in form of plate was successful produced by die pressure casting method. Designed scientific station for casting zirconium based amorphous alloys in the form of plates and rods with selected dimensions is in our university a comprehensive method for achieving amorphous materials which enables us to maintain repeatability of as-cast samples with the amorphous structure and the assumed dimensions range. The diffraction pattern and exothermic reaction as well as the fracture surface morphology reveal that studied as-cast Zr-based alloy is in amorphous state. The calculated GFA parameters show that the alloy exhibits satisfactory glass-forming ability in form of studied plate. These obtained values can suggest that studied alloys are suitable materials for further planned practical application at welding process. The success of Zr-based bulk metallic glasses production in form of plate with obtained sizes is important for future

Preparation and characterization of Zr-based bulk metallic glasses in form of plate

Energy Technology Data Exchange (ETDEWEB)

Pilarczyk, Wirginia, E-mail: wirginia.pilarczyk@polsl.pl

2014-12-05

Highlights: • Zr-based BMGs in form of plate was successful produced by die pressure casting method. • Many techniques have been used to characterize the structure of Zr{sub 55}Cu{sub 30}Ni{sub 5}Al{sub 10} alloy. • The calculated GFA parameters show that the alloy exhibits satisfactory GFA. • The studies reveal that tested as-cast Zr-based alloy is in amorphous state. - Abstract: Zr-based bulk metallic glasses present an interesting combination of physical, chemical and mechanical properties. During the last decade, intensive progress has been made and a number of applications have been suggested for these materials. In order to successfully apply these materials, it is necessary to accurately characterize their structure, thermal stability and other properties accurately. The aim of the presented work is the manufacturing, examination of the structure of selected Zr-based bulk metallic alloys and confirmation of an amorphous structure using X-ray analysis, microscopic observation and thermal analysis. In this work, the Zr-based bulk metallic glasses in form of plate was successful produced by die pressure casting method. Designed scientific station for casting zirconium based amorphous alloys in the form of plates and rods with selected dimensions is in our university a comprehensive method for achieving amorphous materials which enables us to maintain repeatability of as-cast samples with the amorphous structure and the assumed dimensions range. The diffraction pattern and exothermic reaction as well as the fracture surface morphology reveal that studied as-cast Zr-based alloy is in amorphous state. The calculated GFA parameters show that the alloy exhibits satisfactory glass-forming ability in form of studied plate. These obtained values can suggest that studied alloys are suitable materials for further planned practical application at welding process. The success of Zr-based bulk metallic glasses production in form of plate with obtained sizes is

PCB-153 shows different dynamics of mobilisation from differentiated rat adipocytes during lipolysis in comparison with PCB-28 and PCB-118.

Science.gov (United States)

Louis, Caroline; Tinant, Gilles; Mignolet, Eric; Thomé, Jean-Pierre; Debier, Cathy

2014-01-01

Polychlorinated biphenyls (PCBs) are persistent organic pollutants. Due to their lipophilic character, they are preferentially stored within the adipose tissue. During the mobilisation of lipids, PCBs might be released from adipocytes into the bloodstream. However, the mechanisms associated with the release of PCBs have been poorly studied. Several in vivo studies followed their dynamics of release but the complexity of the in vivo situation, which is characterised by a large range of pollutants, does not allow understanding precisely the behaviour of individual congeners. The present in vitro experiment studied the impact of (i) the number and position of chlorine atoms of PCBs on their release from adipocytes and (ii) the presence of other PCB congeners on the mobilisation rate of such molecules. Differentiated rat adipocytes were used to compare the behaviour of PCB-28, -118 and -153. Cells were contaminated with the three congeners, alone or in cocktail, and a lipolysis was then induced with isoproterenol during 12 hours. Our data indicate that the three congeners were efficiently released from adipocytes and accumulated in the medium during the lipolysis. Interestingly, for a same level of cell lipids, PCB-153, a hexa-CB with two chlorine atoms in ortho-position, was mobilised slower than PCB-28, a tri-CB, and PCB-118, a penta-CB, which are both characterised by one chlorine atom in ortho-position. It suggests an impact of the chemical properties of pollutants on their mobilisation during periods of negative energy balance. Moreover, the mobilisation of PCB congeners, taken individually, did not seem to be influenced by the presence of other congeners within adipocytes. These results not only highlight the obvious mobilisation of PCBs from adipocytes during lipolysis, in parallel to lipids, but also demonstrate that the structure of congeners defines their rate of release from adipocytes.

PCB Fault Detection Using Image Processing

Science.gov (United States)

Nayak, Jithendra P. R.; Anitha, K.; Parameshachari, B. D., Dr.; Banu, Reshma, Dr.; Rashmi, P.

2017-08-01

The importance of the Printed Circuit Board inspection process has been magnified by requirements of the modern manufacturing environment where delivery of 100% defect free PCBs is the expectation. To meet such expectations, identifying various defects and their types becomes the first step. In this PCB inspection system the inspection algorithm mainly focuses on the defect detection using the natural images. Many practical issues like tilt of the images, bad light conditions, height at which images are taken etc. are to be considered to ensure good quality of the image which can then be used for defect detection. Printed circuit board (PCB) fabrication is a multidisciplinary process, and etching is the most critical part in the PCB manufacturing process. The main objective of Etching process is to remove the exposed unwanted copper other than the required circuit pattern. In order to minimize scrap caused by the wrongly etched PCB panel, inspection has to be done in early stage. However, all of the inspections are done after the etching process where any defective PCB found is no longer useful and is simply thrown away. Since etching process costs 0% of the entire PCB fabrication, it is uneconomical to simply discard the defective PCBs. In this paper a method to identify the defects in natural PCB images and associated practical issues are addressed using Software tools and some of the major types of single layer PCB defects are Pattern Cut, Pin hole, Pattern Short, Nick etc., Therefore the defects should be identified before the etching process so that the PCB would be reprocessed. In the present approach expected to improve the efficiency of the system in detecting the defects even in low quality images

Fabricating Zr-Based Bulk Metallic Glass Microcomponent by Suction Casting Using Silicon Micromold

Directory of Open Access Journals (Sweden)

Zhijing Zhu

2014-08-01

Full Text Available A suction casting process for fabricating Zr55Cu30Al10Ni5 bulk metallic glass microcomponent using silicon micromold has been studied. A complicated BMG microgear with 50 μm in module has been cast successfully. Observed by scanning electron microscopy and laser scanning confocal microscopy, we find that the cast microgear duplicates the silicon micromold including the microstructure on the surface. The amorphous state of the microgear is confirmed by transmission election microscopy. The nanoindentation hardness and elasticity modulus of the microgear reach 6.5 GPa and 94.5 GPa. The simulation and experimental results prove that the suction casting process with the silicon micromold is a promising one-step method to fabricate bulk metallic glass microcomponents with high performance for applications in microelectromechanical system.

Copper phthalocyanine and metal free phthalocyanine bulk heterojunction photodetector

Energy Technology Data Exchange (ETDEWEB)

Farooq, Amjad, E-mail: amjad.farooq1212@hotmail.com [Wah Engineering College, University of Wah, Wah Cantt. 47040 (Pakistan); GIK Institute of Engineering Sciences and Technology, Topi 23640, Swabi (Pakistan); Karimov, Kh.S. [GIK Institute of Engineering Sciences and Technology, Topi 23640, Swabi (Pakistan); Physical Technical Institute, Aini St. 299/1, Dushanbe 734063 (Tajikistan); Ahmed, Nisar; Ali, Taimoor [GIK Institute of Engineering Sciences and Technology, Topi 23640, Swabi (Pakistan); Khalid Alamgir, M. [National Institute of Vacuum Science and Technology, NCP complex, Islamabad 44000 (Pakistan); Usman, Muhammad [Experimental Physics Laboratories, National Centre for Physics, Quaid-i-Azam University, Islamabad 44000 (Pakistan)

2015-01-15

In this study we present the dependence of electrical properties of copper phthalocyanine (CuPc) and metal free phthalocyanine (H{sub 2}Pc) bulk heterojunction structure under different illumination levels. To fabricate the device on ITO coated glass substrate the bulk heterojunction thin film of CuPc and H{sub 2}Pc with thickness varying from 100 nm to 300 nm are deposited by thermal evaporator. Aluminum thin film was deposited by thermal evaporation as a top contact. The optical properties of the fabricated device are investigated using UV–vis spectroscopy. The current-voltage characteristics in dark and under illumination show that the device is sensitive towards visible light. The absorption spectrum describes its photo sensitivity in the range of wavelength from 200 nm to 850 nm. Simulation of current-intensity of light curve is carried out and experimental results are found in good agreement with simulated ones.

Copper phthalocyanine and metal free phthalocyanine bulk heterojunction photodetector

International Nuclear Information System (INIS)

Farooq, Amjad; Karimov, Kh.S.; Ahmed, Nisar; Ali, Taimoor; Khalid Alamgir, M.; Usman, Muhammad

2015-01-01

In this study we present the dependence of electrical properties of copper phthalocyanine (CuPc) and metal free phthalocyanine (H 2 Pc) bulk heterojunction structure under different illumination levels. To fabricate the device on ITO coated glass substrate the bulk heterojunction thin film of CuPc and H 2 Pc with thickness varying from 100 nm to 300 nm are deposited by thermal evaporator. Aluminum thin film was deposited by thermal evaporation as a top contact. The optical properties of the fabricated device are investigated using UV–vis spectroscopy. The current-voltage characteristics in dark and under illumination show that the device is sensitive towards visible light. The absorption spectrum describes its photo sensitivity in the range of wavelength from 200 nm to 850 nm. Simulation of current-intensity of light curve is carried out and experimental results are found in good agreement with simulated ones

PCB-induced changes of a benthic community and expected ecosystem recovery following in situ sorbent amendment

Science.gov (United States)

Janssen, Elisabeth M.-L.; Thompson, Janet K.; Luoma, Samuel N.; Luthy, Richard G.

2011-01-01

The benthic community was analyzed to evaluate pollution-induced changes for the polychlorinated biphenyl (PCB)-contaminated site at Hunters Point (HP) relative to 30 reference sites in San Francisco Bay, California, USA. An analysis based on functional traits of feeding, reproduction, and position in the sediment shows that HP is depauperate in deposit feeders, subsurface carnivores, and species with no protective barrier. Sediment chemistry analysis shows that PCBs are the major risk drivers at HP (1,570 ppb) and that the reference sites contain very low levels of PCB contamination (9 ppb). Different feeding traits support the existence of direct pathways of exposure, which can be mechanistically linked to PCB bioaccumulation by biodynamic modeling. The model shows that the deposit feeder Neanthes arenaceodentata accumulates approximately 20 times more PCBs in its lipids than the facultative deposit feeder Macoma balthica and up to 130 times more than the filter feeder Mytilus edulis. The comparison of different exposure scenarios suggests that PCB tissue concentrations at HP are two orders of magnitude higher than at the reference sites. At full scale, in situ sorbent amendment with activated carbon may reduce PCB bioaccumulation at HP by up to 85 to 90% under favorable field and treatment conditions. The modeling framework further demonstrates that such expected remedial success corresponds to exposure conditions suggested as the cleanup goal for HP. However, concentrations remain slightly higher than at the reference sites. The present study demonstrates how the remedial success of a sorbent amendment, which lowers the PCB availability, can be compared to reference conditions and traditional cleanup goals, which are commonly based on bulk sediment concentrations.

Thermoplastic deformation of ferromagnetic CoFe-based bulk metallic glasses

Science.gov (United States)

Wu, Chenguang; Hu, Renchao; Man, Qikui; Chang, Chuntao; Wang, Xinmin

2017-12-01

The superplastic deformation behavior of the ferromagnetic Co31Fe31Nb8B30 bulk metallic glass (BMG) in the supercooled liquid region was investigated. At a given temperature, the BMG exhibits a Newtonian behavior at low strain rates but a non-Newtonian behavior at high strain rates. The high thermal stability of this glassy alloy system offers an enough processing window to thermoplastic forming (TPF), and the strong processing ability was examined by simple micro-replication experiments. It is demonstrated that the TPF formability on length scales ranging down to nanometers can be achieved in the selected experimental condition. Based on the analysis of deformation behavior, the nearly full density sample (i.e. nearly 100%), was produced from water-atomized glassy powders and consolidated by the hot-pressing technique. The sample exhibits good soft-magnetic and mechanical properties, i.e., low coercive force of 0.43 Oe, high initial permeability of 4100 and high Vickers hardness 1398. These results suggest that the hot-pressing process opens up possibilities for the commercial exploitation of BMGs in engineering applications.

Development of Low Density CaMg-A1-Based Bulk Metallic Glasses (Preprint)

National Research Council Canada - National Science Library

Senkov, O. N; Scott, J. M; Miracle, D. B

2006-01-01

Low density Ca-Mg-Al-based bulk metallic glasses containing additionally Cu and Zn, were produced by a copper mold casting method as wedge-shaped samples with thicknesses varying from 0.5 mm to 10 rom...

Dechlorination of PCB by radiation

International Nuclear Information System (INIS)

Shinozaki, Yoshiharu

1978-01-01

On the PCB poisoning accident in Japan occurred in 1968, Tokyo Metropolitan Isotope Research Center started to investigate the decomposition of PCB (polychlorinated biphenyl) on the request of Metropolitan government. The research center has found that if PCB is dissolved or extracted in alkaline 2-propanol solution and then irradiated with γ-ray, PCB is dechlorinated in chain-reactive manner, and biphenyl and salts (KCl or NaCl) are formed. Afterwards, it has been found that photolysis has also similar effect on PCB. Then, the basic design of a disposal pilot plant using ultraviolet ray and its economic evaluation have been performed, which is composed of photolysis reaction process, refining process and waste disposal process. However, its disposal cost only has reached the value three times as high as that of incineration process. If this is conducted by radiolysis, its disposal cost can be reduced to about 1/12 of that of ultraviolet ray system when an electron accelerator is employed. Cs-137 source gives better results than Co-60. Dechlorination process of PCB has been thus established. Further reduction of total cost will be the keypoint of radiolysis system to be adopted. If the application of electron accelerators to sludge treatment in the future, the effective use of recovered products, and the possibility of using Cs-137 large sources are considered, it is expected that the disposal cost of radiolysis process system becomes comparable with the incineration process. (Wakatsuki, Y.)

An Investigation into the Non-bulk Rail Freight Transport in Australia

OpenAIRE

Hadi Ghaderi; Stephen Cahoon; Hong-Oanh Nguyen

2015-01-01

In the last decade freight transport has gained further momentum in Australia, partly through significant demand growth at both domestic and international levels and partly as the result of Australia's long term need for infrastructure decision making. Amongst the freight task, non-bulk freight is the fastest growing freight task in Australia and is forecast to grow much faster than the rate of population growth and the average national GDP growth. However, rail's share in the non-bulk market...

Investigation of crystallization kinetics and deformation behavior in supercooled liquid region of CuZr-based bulk metallic glass

Energy Technology Data Exchange (ETDEWEB)

Yang, Ke; Fan, Xinhui; Li, Bing; Li, Yanhong; Wang, Xin; Xu, Xuanxuan [Xi' an Technological Univ. (China). School of Material and Chemical Engineering

2017-08-15

In this paper, a systematic study of crystallization kinetics and deformation behavior is presented for (Cu{sub 50}Zr{sub 50}){sub 94}Al{sub 6} bulk metallic glass in the supercooled liquid region. Crystallization results showed that the activation energy for (Cu{sub 50}Zr{sub 50}){sub 94}Al{sub 6} was calculated using the Arrhenius equation in isothermal mode and the Kissinger-Akahira-Sunose method in non-isothermal mode. The activation energy was quite high compared with other bulk metallic glasses. Based on isothermal transformation kinetics described by the Johson-Mehl-Avrami model, the average Avrami exponent of about 3.05 implies a mainly diffusion controlled three-dimensional growth with an increasing nucleation rate during the crystallization. For warm deformation, the results showed that deformation behavior, composed of homogeneous and inhomogeneous deformation, is strongly dependent on strain rate and temperature. The homogeneous deformation transformed from non-Newtonian flow to Newtonian flow with a decrease in strain rate and an increase in temperature. It was found that the crystallization during high temperature deformation is induced by heating. The appropriate working temperature/strain rate combination for the alloy forming, without in-situ crystallization, was deduced by constructing an empirical deformation map. The optimum process condition for (Cu{sub 50}Zr{sub 50}){sub 94}Al{sub 6} can be expressed as T∝733 K and ∝ ε 10{sup -3} s{sup -1}.

Effect of seafood mediated PCB exposure on desaturase activity and PUFA profile in Faroese septuagenarians

DEFF Research Database (Denmark)

Tøttenborg, Sandra Søgaard; Choi, Anna L; Bjerve, Kristian S

2015-01-01

and desaturase activity. In multiple regression models, PCB exposure was inversely related to the estimated Δ6 desaturase activity resulting in accumulation of precursor fatty acids and decrease in the corresponding product PUFAs. A positive association between PCB and Δ5 desaturation was also found. A relative...... increase in EA was also observed, though only in the third tertile of PCB exposure. Non-linear relationships between the exposure and the desaturase activity were not found. Consuming fish and seafood may not be translated into beneficial fatty acid profiles if the diet simultaneously causes exposure...

Total destruction of PCB transformers

International Nuclear Information System (INIS)

Myers, D.S.

1991-01-01

This paper reports that if elimination of PCB liability, including lingering liabilities, is the goal, then landfilling cannot be and option. The law is clear that the generator of PCB waste is responsible for that waste until this destruction. Landfilling is not destruction. Retrofilling as askarel units will not get rid of all PCB liabilities, either. Askarel retrofilling can only make this claim when it can give a lifetime guaranty of no detectable PCBs. States like Washington and California regulate, as hazardous waste, fluids which contain greater than 2 and 5 ppm PCB, respectively. There is no guarantee that your state will not so regulate PCBs in the future or that the federal laws might tighten up. Therefore, replacement and disposal by Resource Recovery constitutes the only lifetime guarantee on the market that the PCBs in your askarel transformers will never come back to haunt you

Persistent organic pollutants in atmospheric deposition and biomonitoring with Tillandsia usneoides (L.) in an industrialized area in Rio de Janeiro state, southeast Brazil--Part II: PCB and PAH.

Science.gov (United States)

de Souza Pereira, Márcia; Heitmann, Dieter; Reifenhäuser, Werner; Meire, Rodrigo Ornellas; Santos, Luciana Silva; Torres, João Paulo M; Malm, Olaf; Körner, Wolfgang

2007-04-01

Monitoring of immission of persistent organic pollutants in the industrialized area of Volta Redonda (V.R.) and in the National Park of Itatiaia (PNI) in southeast Brazil was performed using an endemic bromeliad species as biomonitor and measuring bulk deposition rates of polychlorinated biphenyls (PCB) and polycyclic aromatic hydrocarbons (PAH). For the sum of PCB, overall deposition rates were between 17 and 314 ng/(m2 day) in winter and between 43 and 81 ng/(m2 day) in summer, respectively. Deposition rates of dioxin-like PCBs ranged from 0.14 to 2.8 pg WHO-TEQ/(m2 day) in winter and from 0.90 to 4.3 pg WHO-TEQ/(m2 day) in summer. PCB deposition rates (total PCB and WHO-TEQ) were in the same range in winter in V.R. and PNI. In summer, contamination levels in V.R. were 6-10-folds higher than in PNI. PCB concentrations in biomonitor samples from V.R. and PNI were in the same range in summer and in winter. Concentrations of total PCB ranged from 14 to 95 microg/kg dry matter (d.m.) in winter and from 18 to 27 microg/kg d.m. in summer, respectively. The TEQ values were between 1.7 and 4.1 ng WHO-TEQ/kg d.m. in winter and between 1.9 and 2.9 ng WHO-TEQ/kg d.m. in summer. PCB concentrations of di-ortho PCB but not of non-ortho PCB were a factor of 2-4 lower in summer in both areas. PCB congener profiles resembled those from technical formulations. The profiles shifted to the higher chlorinated congeners in summer, probable due to revolatilisation of the lighter components at higher temperatures. PCB profiles in biomonitor resembled those from deposition samples and the shift to the heavier congeners in summer was even more pronounced. PAH deposition rates were in a similar range in both areas (131-2415 ng/(m2 day)). PAH levels in biomonitor samples from V.R. were about one order of magnitude higher than in samples from PNI indicating the impact of local sources. PAH profiles revealed stationary thermal processes as main source of contamination in V.R. whereas in PNI

Assessment of LANL PCB waste management documentation

International Nuclear Information System (INIS)

David, K.D.; Hoevemeyer, S.S.; Stirrup, T.S.; Jennrich, E.A.; Lund, D.M.

1991-04-01

The objective of this report is to present findings from evaluating the Los Alamos National Laboratory (LANL) Polychlorinated Biphenyls (PCB) Waste Acceptance Criteria (WAC) to determine if it meets applicable DOE and Code of Federal Regulation (CFR) requirements. DOE Order 5820.2A and 40 CFR 761 (Polychlorinated Biphenyls Manufacturing, Processing, Distribution in Commerce, and Use Prohibitions) set forth requirements and guidelines for the establishment of Waste Acceptance Criteria. The primary purpose of a PCB WAC is to provide generators and waste management with established criteria that must be met before PCB wastes can be accepted for treatment, storage, and/or disposal. An annotated outline for a generic PCB WAC was developed based on the requirements of 5820.2A and 40 CFR 761. The major elements that should be addressed by a PCB WAC were determined to be as follows: Waste Package/Container, Waste Forms, PCB Concentrations, Labeling, and Data Package Certification

Two-step bioleaching of copper and gold from discarded printed circuit boards (PCB).

Science.gov (United States)

Işıldar, Arda; van de Vossenberg, Jack; Rene, Eldon R; van Hullebusch, Eric D; Lens, Piet N L

2016-11-01

An effective strategy for environmentally sound biological recovery of copper and gold from discarded printed circuit boards (PCB) in a two-step bioleaching process was experimented. In the first step, chemolithotrophic acidophilic Acidithiobacillus ferrivorans and Acidithiobacillus thiooxidans were used. In the second step, cyanide-producing heterotrophic Pseudomonas fluorescens and Pseudomonas putida were used. Results showed that at a 1% pulp density (10g/L PCB concentration), 98.4% of the copper was bioleached by a mixture of A. ferrivorans and A. thiooxidans at pH 1.0-1.6 and ambient temperature (23±2°C) in 7days. A pure culture of P. putida (strain WCS361) produced 21.5 (±1.5)mg/L cyanide with 10g/L glycine as the substrate. This gold complexing agent was used in the subsequent bioleaching step using the Cu-leached (by A. ferrivorans and A. thiooxidans) PCB material, 44.0% of the gold was mobilized in alkaline conditions at pH 7.3-8.6, and 30°C in 2days. This study provided a proof-of-concept of a two-step approach in metal bioleaching from PCB, by bacterially produced lixiviants. Copyright © 2015 Elsevier Ltd. All rights reserved.

Heavy metals and polychlorinated biphenyls (PCBs) sedimentation in the Lianhua Mountain Reservoir, Pearl River Delta, China.

Science.gov (United States)

Huang, Jingyu; Amuzu-Sefordzi, Basil; Li, Ming

2015-05-01

The Pearl River Delta is one of the biggest electronics manufacturing regions in the world. Due to the presence of abandoned industrial sites and the proliferation of large-scale electronics companies in the past four decades, it is therefore imperative to investigate the extent of heavy metals and polychlorinated biphenyls (PCBs) contamination in the region. Spatial and temporal distribution of heavy metals (Cr, Cu, Ni, Pb, and Zn) and PCBs (PCB28, PCB52, PCB101, PCB118, PCB138, PCB153, and PCB180) in the Lianhua Mountain reservoir in the Pearl River Delta, Dongguan City, China were examined based on a sedimentary profile analysis. Higher concentrations of the heavy metals detected were recorded in bottom sediments whereas 70% of the detected PCBs recorded maximum concentrations in top sediments. The geo-accumulation indices (Igeo) indicate that the study area is uncontaminated to moderately contaminated. Also, the integrated pollution indices (IPI) were above 1, except Pb, which shows that the study area is contaminated with heavy metals from anthropogenic sources. The concentrations of individual heavy metals and PCBs over a period of 60 years were also analyzed in order to establish a historical trend of pollution in the study area. This study provides baseline information on the level and historical trend of heavy metals and PCBs pollution in the study area.

40 CFR 761.61 - PCB remediation waste.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false PCB remediation waste. 761.61 Section... PROHIBITIONS Storage and Disposal § 761.61 PCB remediation waste. This section provides cleanup and disposal options for PCB remediation waste. Any person cleaning up and disposing of PCBs managed under this section...

NMR signature of evolution of ductile-to-brittle transition in bulk metallic glasses.

Science.gov (United States)

Yuan, C C; Xiang, J F; Xi, X K; Wang, W H

2011-12-02

The mechanical properties of monolithic metallic glasses depend on the structures at atomic or subnanometer scales, while a clear correlation between mechanical behavior and structures has not been well established in such amorphous materials. In this work, we find a clear correlation of (27)Al NMR isotropic shifts with a microalloying induced ductile-to-brittle transition at ambient temperature in bulk metallic glasses, which indicates that the (27)Al NMR isotropic shift can be regarded as a structural signature to characterize plasticity for this metallic glass system. The study provides a compelling approach for investigating and understanding the mechanical properties of metallic glasses from the point of view of electronic structure. © 2011 American Physical Society

Determination of bulk and interface density of states in metal oxide semiconductor thin-film transistors by using capacitance-voltage characteristics

Science.gov (United States)

Wei, Xixiong; Deng, Wanling; Fang, Jielin; Ma, Xiaoyu; Huang, Junkai

2017-10-01

A physical-based straightforward extraction technique for interface and bulk density of states in metal oxide semiconductor thin film transistors (TFTs) is proposed by using the capacitance-voltage (C-V) characteristics. The interface trap density distribution with energy has been extracted from the analysis of capacitance-voltage characteristics. Using the obtained interface state distribution, the bulk trap density has been determined. With this method, for the interface trap density, it is found that deep state density nearing the mid-gap is approximately constant and tail states density increases exponentially with energy; for the bulk trap density, it is a superposition of exponential deep states and exponential tail states. The validity of the extraction is verified by comparisons with the measured current-voltage (I-V) characteristics and the simulation results by the technology computer-aided design (TCAD) model. This extraction method uses non-numerical iteration which is simple, fast and accurate. Therefore, it is very useful for TFT device characterization.

Energy spectrum analysis between single and dual energy source x-ray imaging for PCB non-destructive test

Energy Technology Data Exchange (ETDEWEB)

Park, Kyeong Jin; Kim, Myung Soo; Lee, Min Ju; Kang, Dong Uk; Lee, Dae Hee; Kim, Ye Won; Kim, Chan Kyu; Kim, Hyoung Taek; Kim, Gi Yoon; Cho, Gyu Seong [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-08-15

Reliability of printed circuit board (PCB), which is based on high integrated circuit technology, is having been important because of development of electric and self-driving car. In order to answer these demand, automated X-ray inspection (AXI) is best solution for PCB nondestructive test. PCB is consist of plastic, copper, and, lead, which have low to high Z-number materials. By using dual energy X-ray imaging, these materials can be inspected accurately and efficiently. Dual energy X-ray imaging, that have the advantage of separating materials, however, need some solution such as energy separation method and enhancing efficiency because PCB has materials that has wide range of Z-number. In this work, we found out several things by analysis of X-ray energy spectrum. Separating between lead and combination of plastic and copper is only possible with energy range not dose. On the other hand, separating between plastic and copper is only with dose not energy range. Moreover the copper filter of high energy part of dual X-ray imaging and 50 kVp of low energy part of dual X-ray imaging is best for efficiency.

Energy spectrum analysis between single and dual energy source x-ray imaging for PCB non-destructive test

International Nuclear Information System (INIS)

Park, Kyeong Jin; Kim, Myung Soo; Lee, Min Ju; Kang, Dong Uk; Lee, Dae Hee; Kim, Ye Won; Kim, Chan Kyu; Kim, Hyoung Taek; Kim, Gi Yoon; Cho, Gyu Seong

2015-01-01

Reliability of printed circuit board (PCB), which is based on high integrated circuit technology, is having been important because of development of electric and self-driving car. In order to answer these demand, automated X-ray inspection (AXI) is best solution for PCB nondestructive test. PCB is consist of plastic, copper, and, lead, which have low to high Z-number materials. By using dual energy X-ray imaging, these materials can be inspected accurately and efficiently. Dual energy X-ray imaging, that have the advantage of separating materials, however, need some solution such as energy separation method and enhancing efficiency because PCB has materials that has wide range of Z-number. In this work, we found out several things by analysis of X-ray energy spectrum. Separating between lead and combination of plastic and copper is only possible with energy range not dose. On the other hand, separating between plastic and copper is only with dose not energy range. Moreover the copper filter of high energy part of dual X-ray imaging and 50 kVp of low energy part of dual X-ray imaging is best for efficiency

Nanopatterned bulk metallic glass-based biomaterials modulate macrophage polarization.

Science.gov (United States)

Shayan, Mahdis; Padmanabhan, Jagannath; Morris, Aaron H; Cheung, Bettina; Smith, Ryan; Schroers, Jan; Kyriakides, Themis R

2018-06-01

Polarization of macrophages by chemical, topographical and mechanical cues presents a robust strategy for designing immunomodulatory biomaterials. Here, we studied the ability of nanopatterned bulk metallic glasses (BMGs), a new class of metallic biomaterials, to modulate murine macrophage polarization. Cytokine/chemokine analysis of IL-4 or IFNγ/LPS-stimulated macrophages showed that the secretion of TNF-α, IL-1α, IL-12, CCL-2 and CXCL1 was significantly reduced after 24-hour culture on BMGs with 55 nm nanorod arrays (BMG-55). Additionally, under these conditions, macrophages increased phagocytic potential and exhibited decreased cell area with multiple actin protrusions. These in vitro findings suggest that nanopatterning can modulate biochemical cues such as IFNγ/LPS. In vivo evaluation of the subcutaneous host response at 2 weeks demonstrated that the ratio of Arg-1 to iNOS increased in macrophages adjacent to BMG-55 implants, suggesting modulation of polarization. In addition, macrophage fusion and fibrous capsule thickness decreased and the number and size of blood vessels increased, which is consistent with changes in macrophage responses. Our study demonstrates that nanopatterning of BMG implants is a promising technique to selectively polarize macrophages to modulate the immune response, and also presents an effective tool to study mechanisms of macrophage polarization and function. Implanted biomaterials elicit a complex series of tissue and cellular responses, termed the foreign body response (FBR), that can be influenced by the polarization state of macrophages. Surface topography can influence polarization, which is broadly characterized as either inflammatory or repair-like. The latter has been linked to improved outcomes of the FBR. However, the impact of topography on macrophage polarization is not fully understood, in part, due to a lack of high moduli biomaterials that can be reproducibly processed at the nanoscale. Here, we studied

Thermal stability and magnetocaloric properties of GdDyAlCo bulk metallic glasses

Energy Technology Data Exchange (ETDEWEB)

Liang, L. [State Key Laboratory for Advanced Metals and Materials, University of Science and Technology Beijing, Beijing 100083 (China); Hui, X. [State Key Laboratory for Advanced Metals and Materials, University of Science and Technology Beijing, Beijing 100083 (China)], E-mail: huixd01@hotmail.com; Chen, G.L. [State Key Laboratory for Advanced Metals and Materials, University of Science and Technology Beijing, Beijing 100083 (China)

2008-01-25

Gd{sub 56-x}Dy{sub x}Al{sub 24}Co{sub 20} (x = 16, 20 and 22) bulk metallic glasses (BMGs) alloys with a diameter of 2, 3 and 3 mm, respectively, were prepared by using copper mold casting. These alloys exhibit higher values of the glass transition temperature, crystallization temperature, and activation energy of the glass transition and crystallization, compared with those of other known rare-earth-based BMGs. A maximum magnetic entropy changes of 15.78 J/(kg K) is obtained in Gd{sub 40}Dy{sub 16}Al{sub 24}Co{sub 20}, which is the maximal among all the bulk metallic glasses, and is much larger than those of the known crystalline magnetic refrigerant compound Gd{sub 5}Si{sub 2}Ge{sub 1.9}Fe{sub 0.1} and pure Gd metal. All the three BMG alloys have a broader temperature range of the entropy change peak, resulting in larger refrigerate capacities (RC) than those of conventional crystalline materials. The excellent magnetocaloric properties combining with high thermal stability make them an attractive candidate for magnetic refrigerants in the temperature range of 20-100 K.

Polychlorinated Biphenyls (PCB) Residue Effects Database

Data.gov (United States)

U.S. Environmental Protection Agency — The PCB Residue Effects (PCBRes) Database was developed to assist scientists and risk assessors in correlating PCB and dioxin-like compound residues with toxic...

A multi-component Zr alloy with comparable strength and Higher plasticity than Zr-based bulk metallic glasses

International Nuclear Information System (INIS)

Liang, S.X.; Yin, L.X.; Ma, M.Z.; Jing, R.; Yu, P.F.; Zhang, Y.F.; Wang, B.A.; Liu, R.P.

2013-01-01

Zirconium (Zr)-based bulk metallic glass possesses the highest potential as a structural material among metallic glasses. Although Zr-based bulk metallic glass exhibits extremely high strength, its potential application has been restricted by a number of issues, such as fragility, small size, difficult fabrication into different shapes and poisonous beryllium content, among others. In this paper, a Zr-based crystal alloy with comparable strength and higher plasticity than Zr-based bulk metallic glass is presented. The proposed Zr-based alloy has a tensile strength greater than 1600 MPa. That value is comparable to the 1500 MPa to 2000 MPa strength of Zr-based bulk metallic glasses (BMGs). The ductility in terms of elongation reached 6.2%; at the same time, the 1400 MPa tensile strength was retained. This phenomenon is not possible for Zr-based BMGs. XRD results show that the proposed ultrahigh-strength Zr-based crystal alloy has two-phase structures: an hcp-structured α phase and a bcc-structured β phase. The forged specimen exhibits a typical basket-weave microstructure, which is characterised by the interlaced plate α phase separated from the β phase matrix. Fine, short bar-shaped α phases precipitated along the original β grain boundary together with ultrafine dot-shaped α phases that presented inside the original β grain when the ageing temperature was between 500 °C and 525 °C. As the ageing temperature increased, the dot-shaped α phase grew into plate shapes, decreasing the material's strength and increasing its plasticity. The ultrafine dot-shaped and short bar-shaped α phases in the original β phase matrix are the main strengthening mechanisms of the ultrahigh-strength Zr-based crystal alloy.

Oxidation behaviour of Zr-based bulk metallic glasses

International Nuclear Information System (INIS)

Wang, Bin

2011-01-01

The Zr-based bulk metallic glasses, developed since the late 1980's, have very interesting mechanical properties, which can be considered for many applications including working under oxidizing atmosphere conditions at high temperatures. It is therefore interesting to study their oxidation resistance and to characterize the oxide scale formed on alloys surface. The fundamental objective of this thesis is to enhance the understanding of the role of various thermodynamic and chemistry parameters on the oxidation behaviour of the Zr-based bulk metallic glasses at high temperature under dry air, to determine the residual stresses in the oxide layer, in comparison with their crystalline alloys with the same chemical composition after an annealing treatment. The oxidation kinetics of these glasses and the crystalline structure of oxide scale ZrO 2 depend on the temperature and the oxidation duration: for short periods of oxidation or at a temperature below Tg, the kinetics follows a parabolic law, whereas, if the sample is oxidized at T ≥ Tg, the kinetics can be divided into two parts. The crystalline counterparts are oxidized by a parabolic rule whatever the temperature; for long oxidation duration at a temperature close to Tg, the kinetics becomes more complex because of the crystallisation of the glasses during the oxidation tests. Also the crystalline structure of the oxide layers depends on the oxidation temperature: the oxide layer consists only in tetragonal Zirconia at T ≤ Tg, while monoclinic Zirconia was formed at higher temperature. The mechanism of the formation of the oxide scale is due to both the interior diffusion of Oxygen ions and the external diffusion of Zirconium ions. However the diffusion of Zirconium ions slows gradually during the crystallisation process of the glass matrix. When the crystallisation is completed, the formation of Zirconia is controlled by only the internal diffusion of oxygen ions. The corresponding residual stresses

Association of plasma PCB levels and HbA1c concentration in Iran.

Science.gov (United States)

Eftekhari, Sahar; Aminian, Omid; Moinfar, Zeinab; Schettgen, Thomas; Kaifie, Andrea; Felten, Michael; Kraus, Thomas; Esser, André

2018-01-01

The rapid increase in prevalence of diabetes mellitus over the last decades warrants more attention to the effects of environmental and occupational exposures on glucose metabolism. Our study aimed to assess the association between the plasma levels of various congeners of polychlorinated biphenyls (PCBs) and the serum concentration of glycated haemoglobin (HbA1c). Our study population consisted of 140 Iranian adults from seven different occupational groups and a group of non-occupationally exposed female participants. The plasma concentration of PCBs were determined at the laboratory of occupational toxicology at RWTH Aachen University, Germany. We considered an HbA1c concentration of 5.7% and more as indicating a disturbed glucose metabolism. Logistic regression was used to assess the association between quartiles of concentrations of PCB congeners and serum HbA1c. Participants with an increased HbA1c value had higher plasma levels of PCB 138, 153, 180 and the PCB sum, although this association was statistically not significant. There was no significant difference between the levels of PCB 138, 153, 180, the sum of these congeners, and PCB 118 in their quartiles when comparing with HbA1c concentrations. For our cohort, we could not demonstrate a significant association between PCB and HbA1c concentrations indicating a disturbance of glucose metabolism.

Complete PCB design using OrCAD capture and PCB editor

CERN Document Server

Mitzner, Kraig

2009-01-01

This book provides instruction on how to use the OrCAD design suite to design and manufacture printed circuit boards. The primary goal is to show the reader how to design a PCB using OrCAD Capture and OrCAD Editor. Capture is used to build the schematic diagram of the circuit, and Editor is used to design the circuit board so that it can be manufactured. The book is written for both students and practicing engineers who need in-depth instruction on how to use the software, and who need background knowledge of the PCB design process. KEY FEATURES:* Beginning to end cove

Viscous surface flow induced on Ti-based bulk metallic glass by heavy ion irradiation

Energy Technology Data Exchange (ETDEWEB)

Zhang, Kun [Key Laboratory of Microgravity (National Microgravity Laboratory), Institute of Mechanics, Chinese Academy of Sciences, Beijing 100190 (China); Hu, Zheng [Key Laboratory of Microgravity (National Microgravity Laboratory), Institute of Mechanics, Chinese Academy of Sciences, Beijing 100190 (China); Science and Technology on Vehicle Transmission Laboratory, China North Vehicle Research Institute, Beijing 100072 (China); Li, Fengjiang [Key Laboratory of Microgravity (National Microgravity Laboratory), Institute of Mechanics, Chinese Academy of Sciences, Beijing 100190 (China); Wei, Bingchen, E-mail: weibc@imech.ac.cn [Key Laboratory of Microgravity (National Microgravity Laboratory), Institute of Mechanics, Chinese Academy of Sciences, Beijing 100190 (China)

2016-12-30

Highlights: • Obvious smoothing and roughening phases on the Ti-based MG surface resulted, which correspond respectively to the normal and off-normal incidence angles. • Atomic force microscopy confirms two types of periodic ripples distributed evenly over the rough surface. • The irradiation-induced viscosity of MG is about 4×10{sup 12} Pa·s, which accords with the theoretical prediction for metallic glasses close to glass transition temperature. • Surface-confined viscous flow plays a dominant quantitative role, which is due to radiation-induced softening of the low-viscosity surface layer. - Abstract: Ti-based bulk metallic glass was irradiated by a 20 MeV Cl{sup 4+} ion beam under liquid-nitrogen cooling, which produced remarkable surface smoothing and roughening that respectively correspond to normal and off-normal incidence angles of irradiation. Atomic force microscopy confirms two types of periodic ripples distributed evenly over the rough glass surface. In terms of mechanism, irradiation-induced viscosity agrees with the theoretical prediction for metallic glasses near glass transition temperature. Here, a model is introduced, based on relaxation of confined viscous flow with a thin liquid-like layer, that explains both surface smoothing and ripple formation. This study demonstrates that bulk metallic glass has high morphological instability and low viscosity under ion irradiation, which assets can pave new paths for metallic glass applications.

Evaluation of cumulative PCB exposure estimated by a job exposure matrix versus PCB serum concentrations

Science.gov (United States)

Ruder, Avima M.; Succop, Paul; Waters, Martha A.

2015-01-01

Although polychlorinated biphenyls (PCBs) have been banned in many countries for more than three decades, exposures to PCBs continue to be of concern due to their long half-lives and carcinogenic effects. In National Institute for Occupational Safety and Health studies, we are using semiquantitative plant-specific job exposure matrices (JEMs) to estimate historical PCB exposures for workers (n=24,865) exposed to PCBs from 1938 to 1978 at three capacitor manufacturing plants. A subcohort of these workers (n=410) employed in two of these plants had serum PCB concentrations measured at up to four times between 1976 and 1989. Our objectives were to evaluate the strength of association between an individual worker’s measured serum PCB levels and the same worker’s cumulative exposure estimated through 1977 with the (1) JEM and (2) duration of employment, and to calculate the explained variance the JEM provides for serum PCB levels using (3) simple linear regression. Consistent strong and statistically significant associations were observed between the cumulative exposures estimated with the JEM and serum PCB concentrations for all years. The strength of association between duration of employment and serum PCBs was good for highly chlorinated (Aroclor 1254/HPCB) but not less chlorinated (Aroclor 1242/LPCB) PCBs. In the simple regression models, cumulative occupational exposure estimated using the JEMs explained 14–24 % of the variance of the Aroclor 1242/LPCB and 22–39 % for Aroclor 1254/HPCB serum concentrations. We regard the cumulative exposure estimated with the JEM as a better estimate of PCB body burdens than serum concentrations quantified as Aroclor 1242/LPCB and Aroclor 1254/HPCB. PMID:23475397

Deformation-strengthening during rolling Cu60Zr20Ti20 bulk metallic glass

DEFF Research Database (Denmark)

Cao, Q.P.; Li, J.F.; Hu, Yuyan

2007-01-01

Mechanical strength evolutions during rolling the Cu60Zr20Ti20 bulk metallic glass (BMG) at room temperature (RT) and cryogenic temperature (CT) have been investigated by measuring the microhardness. The hardness slightly increases during the initial rolling stage as a result of the gradually...

PCB dechlorination in anaerobic soil slurry reactors

International Nuclear Information System (INIS)

Klasson, K.T.; Evans, B.S.

1993-01-01

Many industrial locations, including the US Department of Energy's, have identified needs for treatment of polychlorinated biphenyl (PCB) wastes and remediation of PCB-contaminated sites. Biodegradation of PCBs is a potentially effective technology for the treatment of PCB-contaminated soils and sludges, including mixed wastes; however, a practical remediation technology has not yet been demonstrated. In laboratory experiments, soil slurry bioreactors inoculated with microorganisms extracted from PCB-contaminated sediments from the Hudson River have been used to obtain anaerobic dechlorination of PCBS. The onset of dechlorination activity can be accelerated by addition of nutritional amendments and inducers. After 15 weeks of incubation with PCB-contaminated soil and nutrient solution, dechlorination has been observed under several working conditions. The best results show that the average chlorine content steadily dropped from 4.3 to 3.5 chlorines per biphenyl over a 15-week period

New insight on glass-forming ability and designing Cu-based bulk metallic glasses: The solidification range perspective

International Nuclear Information System (INIS)

Wu, Jili; Pan, Ye; Li, Xingzhou; Wang, Xianfei

2014-01-01

Highlights: • The equation, T rg = T g /T l , was rotationally modified to T rg = κ(T m /T l ) + C/T l . • The newly generalized equation suggests a way for describing glass-forming ability. • Several new Cu-based bulk metallic glasses were discovered by solidification range. - Abstract: In this paper, a new equation was rationally generalized from the reduced glass transition temperature. This equation indicates that solidification range can be used for describing glass-forming ability, which can be calculated with the aid of computational thermodynamic approach. Based on this scenario, several new Cu-based bulk metallic glasses in the ternary Cu–Zr–Ti alloy system were discovered. The as-cast samples were characterized by X-ray diffraction and transmission electronic microscopy. The results indicate that as-cast samples have monolithic amorphous nature. Thermal analysis validates that the smaller solidification range is closely related to the higher glass-forming ability, which is contributed to the effect of solidification time on the formation of bulk metallic glasses. This work also suggests that solidus can influence glass formation

In situ visualization of Ni-Nb bulk metallic glasses phase transition

OpenAIRE

Oreshkin, A. I.; Mantsevich, V. N.; Savinov, S. V.; Oreshkin, S. I.; Panov, V. I.; Yavari, A. R.; Miracle, D. B.; Louzguine-Luzgin, D. V.

2013-01-01

We report the results of the Ni-based bulk metallic glass structural evolution and crystallization behavior in situ investigation. The X-ray diffraction (XRD), transmission electron microscopy (TEM), nano-beam diffraction (NBD), differential scanning calorimetry (DSC), radial distribution function (RDF) and scanning probe microscopy/spectroscopy (STM/STS) techniques were applied to analyze the structure and electronic properties of Ni63.5Nb36.5 glasses before and after crystallization. It was...

PCB eksponering i Farum Midtpunkt

DEFF Research Database (Denmark)

Meyer, Harald William; Frederiksen, Marie; Ebbehøj, Niels Erik

I marts og april 2011 blev i alt 104 lejligheder og 289 beboere fra Farum Midtpunkt undersøgt for niveauer af PolyChlorerede Biphenyler (PCB) i henholdsvis fuger og indeluft i lejligheder-ne, og i blodplasma. Til analyserne i denne rapport indgik 273 beboere, 139 fra PCB-forurenede lejligheder og...... 134 fra ikke-forurenede lejligheder. Der blev indsamlet luftprøver fra 83 forure-nede og 21 ikke-forurenede lejligheder og fugeprøver fra 20 forurenede lejligheder. Ni ud af 24 målte PCB-kongenere var under detektionsgrænsen i luften, inkl. de to mest toksiske kongenere nr. 126 og 169. For de...... forurenede lejlig-heder, undtagen for nr. 183 og 190, samt for nr. 182 som alle lå under detektionsgrænsen. For ni ud af tolv dioxin-lignende PCB-forbindelser var alle, eller næsten alle prøver under detektions-grænsen. For nr. 105 og 118 sås signifikant højere niveau blandt eksponerede. Mænd havde et lidt...

Spectral descriptors for bulk metallic glasses based on the thermodynamics of competing crystalline phases

OpenAIRE

Perim, Eric; Lee, Dongwoo; Liu, Yanhui; Toher, Cormac; Gong, Pan; Li, Yanglin; Simmons, W. Neal; Levy, Ohad; Vlassak, Joost J.; Schroers, Jan; Curtarolo, Stefano

2016-01-01

Metallic glasses have attracted considerable interest in recent years due to their unique combination of superb properties and processability. Predicting bulk metallic glass formers from known parameters remains a challenge and the search for new systems is still performed by trial and error. It has been speculated that some sort of "confusion" during crystallization of the crystalline phases competing with glass formation could play a key role. Here, we propose a heuristic descriptor quantif...

A Fundamental Approach to Developing Aluminium based Bulk Amorphous Alloys based on Stable Liquid Metal Structures and Electronic Equilibrium - 154041

Science.gov (United States)

2017-03-28

AFRL-AFOSR-JP-TR-2017-0027 A Fundamental Approach to Developing Aluminium -based Bulk Amorphous Alloys based on Stable Liquid-Metal Structures and...to 16 Dec 2016 4.  TITLE AND SUBTITLE A Fundamental Approach to Developing Aluminium -based Bulk Amorphous Alloys based on Stable Liquid-Metal...Air Force Research Laboratory for accurately predicting compositions of new amorphous alloys specifically based on aluminium with properties superior

PCB i bygninger - afhjælpning, renovering og nedrivning

DEFF Research Database (Denmark)

Andersen, Helle Vibeke

SBi-anvisning 268 beskriver, hvordan PCB-forurening af indeluften afhjælpes, og hvordan PCB håndteres, når man renoverer eller nedriver bygninger med PCB. Uanset om der er tale om afhjælpning, renovering eller nedrivning, kan arbejdet generere PCB-holdigt affald. Anvisningen forklarer derfor......, hvordan affaldet skal håndteres, og hvordan man beskytter mennesker og miljø under arbejdet. Anvisningen er baseret på byggebranchens erfaringer og den aktuelle forskningsbaserede viden om PCB i bygninger. SBi-anvisning 268 afløser den snart fire år gamle SBi-anvisning 242 om renovering af bygninger med...... PCB, som ikke behandlede spørgsmålet om affaldshåndtering....

PCB concentrations of lake whitefish (Coregonus clupeaformis) vary by sex

Science.gov (United States)

Madenjian, Charles P.; Ebener, Mark P.; Sepulveda, Maria S.

2015-01-01

We determined whole-fish polychlorinated biphenyl (PCB) concentrations in 26 female lake whitefish (Coregonus clupeaformis) and 34 male lake whitefish from northern Lake Huron. In 5 of the 26 female lake whitefish, we also determined PCB concentrations in the somatic tissue and ovaries. In addition, bioenergetics modeling was used to determine the contribution of the growth dilution effect to the observed difference in PCB concentrations between the sexes. Whole-fish PCB concentrations for females and males averaged 60 ng/g and 80 ng/g, respectively; thus males were 34% higher in PCB concentration compared with females. Based on the PCB determinations in the somatic tissue and ovaries, we predicted that PCB concentration of females would increase by 2.5%, on average, immediately after spawning due to release of eggs. Thus, the change in PCB concentration due to release of eggs did not explain, to any degree, the higher PCB concentrations observed in males compared with females. Bioenergetics modeling results indicated that the growth dilution effect could account for males being only 0.7% higher in PCB concentration compared with females. Thus, the growth dilution effect contributed very little to the observed difference in PCB concentrations between the sexes. We conclude that males were higher than females in PCB concentration most likely due to a higher rate of energy expenditure, stemming from greater activity and a greater resting metabolic rate. A higher rate of energy expenditure leads to a higher rate of food consumption, which, in turn, leads to a higher PCB accumulation rate.

An environment-dependent semi-empirical tight binding model suitable for electron transport in bulk metals, metal alloys, metallic interfaces, and metallic nanostructures. I. Model and validation

Energy Technology Data Exchange (ETDEWEB)

Hegde, Ganesh, E-mail: ghegde@purdue.edu; Povolotskyi, Michael; Kubis, Tillmann; Klimeck, Gerhard, E-mail: gekco@purdue.edu [Network for Computational Nanotechnology (NCN), Department of Electrical and Computer Engineering, Purdue University, West Lafayette, Indiana 47907 (United States); Boykin, Timothy [Department of Electrical and Computer Engineering, University of Alabama, Huntsville, Alabama (United States)

2014-03-28

Semi-empirical Tight Binding (TB) is known to be a scalable and accurate atomistic representation for electron transport for realistically extended nano-scaled semiconductor devices that might contain millions of atoms. In this paper, an environment-aware and transferable TB model suitable for electronic structure and transport simulations in technologically relevant metals, metallic alloys, metal nanostructures, and metallic interface systems are described. Part I of this paper describes the development and validation of the new TB model. The new model incorporates intra-atomic diagonal and off-diagonal elements for implicit self-consistency and greater transferability across bonding environments. The dependence of the on-site energies on strain has been obtained by appealing to the Moments Theorem that links closed electron paths in the system to energy moments of angular momentum resolved local density of states obtained ab initio. The model matches self-consistent density functional theory electronic structure results for bulk face centered cubic metals with and without strain, metallic alloys, metallic interfaces, and metallic nanostructures with high accuracy and can be used in predictive electronic structure and transport problems in metallic systems at realistically extended length scales.

An environment-dependent semi-empirical tight binding model suitable for electron transport in bulk metals, metal alloys, metallic interfaces, and metallic nanostructures. I. Model and validation

International Nuclear Information System (INIS)

Hegde, Ganesh; Povolotskyi, Michael; Kubis, Tillmann; Klimeck, Gerhard; Boykin, Timothy

2014-01-01

Semi-empirical Tight Binding (TB) is known to be a scalable and accurate atomistic representation for electron transport for realistically extended nano-scaled semiconductor devices that might contain millions of atoms. In this paper, an environment-aware and transferable TB model suitable for electronic structure and transport simulations in technologically relevant metals, metallic alloys, metal nanostructures, and metallic interface systems are described. Part I of this paper describes the development and validation of the new TB model. The new model incorporates intra-atomic diagonal and off-diagonal elements for implicit self-consistency and greater transferability across bonding environments. The dependence of the on-site energies on strain has been obtained by appealing to the Moments Theorem that links closed electron paths in the system to energy moments of angular momentum resolved local density of states obtained ab initio. The model matches self-consistent density functional theory electronic structure results for bulk face centered cubic metals with and without strain, metallic alloys, metallic interfaces, and metallic nanostructures with high accuracy and can be used in predictive electronic structure and transport problems in metallic systems at realistically extended length scales

An environment-dependent semi-empirical tight binding model suitable for electron transport in bulk metals, metal alloys, metallic interfaces, and metallic nanostructures. I. Model and validation

Science.gov (United States)

Hegde, Ganesh; Povolotskyi, Michael; Kubis, Tillmann; Boykin, Timothy; Klimeck, Gerhard

2014-03-01

Semi-empirical Tight Binding (TB) is known to be a scalable and accurate atomistic representation for electron transport for realistically extended nano-scaled semiconductor devices that might contain millions of atoms. In this paper, an environment-aware and transferable TB model suitable for electronic structure and transport simulations in technologically relevant metals, metallic alloys, metal nanostructures, and metallic interface systems are described. Part I of this paper describes the development and validation of the new TB model. The new model incorporates intra-atomic diagonal and off-diagonal elements for implicit self-consistency and greater transferability across bonding environments. The dependence of the on-site energies on strain has been obtained by appealing to the Moments Theorem that links closed electron paths in the system to energy moments of angular momentum resolved local density of states obtained ab initio. The model matches self-consistent density functional theory electronic structure results for bulk face centered cubic metals with and without strain, metallic alloys, metallic interfaces, and metallic nanostructures with high accuracy and can be used in predictive electronic structure and transport problems in metallic systems at realistically extended length scales.

Nanopatterned Bulk Metallic Glass Biosensors.

Science.gov (United States)

Kinser, Emily R; Padmanabhan, Jagannath; Yu, Roy; Corona, Sydney L; Li, Jinyang; Vaddiraju, Sagar; Legassey, Allen; Loye, Ayomiposi; Balestrini, Jenna; Solly, Dawson A; Schroers, Jan; Taylor, André D; Papadimitrakopoulos, Fotios; Herzog, Raimund I; Kyriakides, Themis R

2017-12-22

Nanopatterning as a surface area enhancement method has the potential to increase signal and sensitivity of biosensors. Platinum-based bulk metallic glass (Pt-BMG) is a biocompatible material with electrical properties conducive for biosensor electrode applications, which can be processed in air at comparably low temperatures to produce nonrandom topography at the nanoscale. Work presented here employs nanopatterned Pt-BMG electrodes functionalized with glucose oxidase enzyme to explore the impact of nonrandom and highly reproducible nanoscale surface area enhancement on glucose biosensor performance. Electrochemical measurements including cyclic voltammetry (CV) and amperometric voltammetry (AV) were completed to compare the performance of 200 nm Pt-BMG electrodes vs Flat Pt-BMG control electrodes. Glucose dosing response was studied in a range of 2 mM to 10 mM. Effective current density dynamic range for the 200 nm Pt-BMG was 10-12 times greater than that of the Flat BMG control. Nanopatterned electrode sensitivity was measured to be 3.28 μA/cm 2 /mM, which was also an order of magnitude greater than the flat electrode. These results suggest that nonrandom nanotopography is a scalable and customizable engineering tool which can be integrated with Pt-BMGs to produce biocompatible biosensors with enhanced signal and sensitivity.

Reference standards for quantitative trace analysis of PCB's by GC. Technical PCB formulations for the calibration of ECD and MSD responses

Energy Technology Data Exchange (ETDEWEB)

Krupcik, J. (Slovak Technical Univ., Department of Analytical Chemistry, Bratislava (Slovakia)); Kocan, A. (Institute of Preventive Medicine, Bratislava (Slovakia)); Petrik, J. (Institute of Preventive Medicine, Bratislava (Slovakia)); Leclercq, P.A. (Eindhoven University of Technology, Dept. of Chemical Engineering, Lab. of Instrumental Analysis (Netherlands)); Ballschmiter, K. (University of Ulm, Dept. of Analytical and Environmental Chemistry (Germany))

1993-04-01

The composition of any technical PCB formulation can be determined directly by analyzing the PCB sample by gas chromatography with a flame ionization detector (GC-FID), provided the relative molecular masses of the components are known. The response of electron capture and selected-ion monitoring, mass-spectra detectors can then be calibrated for individual PCB congeners by correlation of the chromatographic patterns with those of concentrated PCB samples obtained by GC-FID. This procedure, which uses a given technical PCB formulation as a secondary reference standard mixture, is to be preferred over existing calibration methods, when results with [+-]10% errors are acceptable because commercial PCB formulations cover the whole range of chlorination products. (orig.)

A New Approach for Handling of Micro Parts in Bulk Metal Forming

DEFF Research Database (Denmark)

Mahshid, Rasoul; Hansen, Hans Nørgaard; Arentoft, M.

2012-01-01

of production [1]. This can fulfill the demands for mass production and miniaturization in industries and academic communities. According to the recent studies, topics related to materials, process and simulation have been investigated intensively and well documented. Machines, forming tools and handling...... systems are critical elements to complete micro forming technology for transferring knowledge to industries and toward miniature manufacturing systems (micro factory) [2]. Since most metal forming processes are multi stage, making a new handling system with high reliability on accuracy and speed...... have been optimized or handling systems based on new concepts for gripping and releasing micro parts have been proposed. Making a handling system for micro parts made by sheet metals or foils is easier than those in bulk metal forming because parts are attached to the sheet during the forming process...

PCDD/F and dioxin-like PCB in human blood and milk from German mothers

Energy Technology Data Exchange (ETDEWEB)

Wittsiepe, J.; Schrey, P.; Lemm, F.; Wilhelm, M. [Ruhr-Univ. Bochum, Abt. fuer Hygiene, Sozial- und Umweltmedizin (Germany); Fuerst, P. [Chemisches Landes- und Staatliches Veterinaeruntersuchungsamt, Muenster (Germany); Kraft, M. [Ministerium fuer Umwelt und Naturschutz, Landwirtschaft und Verbraucherschutz des Landes Nordrhein-Westfalen, Duesseldorf (Germany); Eberwein, G. [Landesumweltamt Nordrhein-Westfalen, Essen (Germany); Winneke, G. [Medizinisches Inst. fuer Umwelthygiene an der Heinrich-Heine Univ. Duesseldorf (Germany)

2004-09-15

Human biomonitoring of polychlorinated dibenzo-p-dioxins and dibenzofuranes (PCDD/F) and polychlorinated biphenyls (PCB) is done by analyzing both blood and milk samples. With reference to calculation of Toxicity Equivalents (TEq) as published by the World Health Organization (WHO) in 1998 determination of 17 PCDD/F congeners together with 4 non- and 8 mono-ortho PCB congeners is the preferred method. In contrast to data on PCDD/F only little is known on background levels of dioxin-like PCB in human blood or milk samples. In the present study we report on PCDD/F and PCB levels in human blood samples of pregnant women living in an industrialized area of Germany and of human milk samples from the same women taken in the first weeks after birth. The investigations demonstrate the current background levels found in Germany, make a contribution for the assessment of preand postnatal exposure of infants and show correlations between the two matrices.

Ductile Damage and Fatigue Behavior of Semi-Finished Tailored Blanks for Sheet-Bulk Metal Forming Processes

Science.gov (United States)

Besserer, Hans-Bernward; Hildenbrand, Philipp; Gerstein, Gregory; Rodman, Dmytro; Nürnberger, Florian; Merklein, Marion; Maier, Hans Jürgen

2016-03-01

To produce parts from sheet metal with thickened functional elements, bulk forming operations can be employed. For this new process class, the term sheet-bulk metal forming has been established recently. Since sheet-bulk metal forming processes such as orbital forming generates triaxial stress and strain states, ductile damage is induced in the form of voids in the microstructure. Typical parts will experience cyclic loads during service, and thus, the influence of ductile damage on the fatigue life of parts manufactured by orbital forming is of interest. Both the formation and growth of voids were characterized following this forming process and then compared to the as-received condition of the ferritic deep drawing steel DC04 chosen for this study. Subsequent to the forming operation, the specimens were fatigued and the evolution of ductile damage and the rearrangement of the dislocation networks occurring during cyclic loading were determined. It was shown, that despite an increased ductile damage due to the forming process, the induced strain hardening has a positive effect on the fatigue life of the material. However, by analyzing the fatigued specimens a development of the ductile damage by an increasing number of voids and a change in the void shape were detected.

Crystallization of Pd40CU30Ni10P20 bulk metallic glass with and without pressure

DEFF Research Database (Denmark)

Yang, B.; Jiang, Jianzhong; Zhuang, Yanxin

2007-01-01

The glass-transition behavior of Pd40Cu30Ni10P20 bulk metallic glass was investigated by differential scanning calorimetry (DSC) and X-ray powder diffraction (XRD). The effect of pressure on the crystallization behavior of Pd40Cu30Ni10P20 bulk glass was studied by in situ high-pressure and high...

Liquid phase and supercooled liquid phase welding of bulk metallic glasses

International Nuclear Information System (INIS)

Kawamura, Y.

2004-01-01

Recent progress on welding in bulk metallic glasses (BMGs) has been reviewed. BMGs have been successfully welded to BMGs or crystalline metals by liquid phase welding using explosion, pulse-current and electron-beam methods, and by supercooled liquid phase welding using friction method. Successful welding of the liquid phase methods was due to the high glass-forming ability of the BMGs and the high concentration of welding energy in these methods. In contrast, the supercooled liquid phase welding was successful due to the thermally stable supercooled liquid state of the BMGs and the superplasticity and viscous flow of the supercooled liquid. The successful welding of BMGs to BMGs and crystalline materials is promising for the future development of BMGs as engineering materials

Thermal dechlorination of PCB-209 over Ca species-doped Fe₂O₃.

Science.gov (United States)

Su, Guijin; Huang, Linyan; Shi, Ruifang; Liu, Yexuan; Lu, Huijie; Zhao, Yuyang; Yang, Fan; Gao, Lirong; Zheng, Minghui

2016-02-01

Degradation reaction of decachlorobiphenyl (PCB-209) was investigated over the synthesized Ca species-doped Fe2O3 at 300 °C. The 1%Ca-Fe2O3 exhibited the highest activity among the four catalysts prepared with the pseudo-first order reaction at k(obs) = 0.103 min(-1). PCB-207, PCB-197, PCB-176, PCB-184, PCB-150, PCB-136, PCB-148, PCB-104, PCB-96, PCB-54, PCB-19, PCB-4 and PCB-1 were identified as the dominant isomers in their respective nonachlorobiphenyl (NonaCB) to monochlorobiphenyl (MonoCB) homologue groups. Analysis of the hydrodechlorination products indicated that dechlorination was much more favored on meta- and para-than on ortho-positions. The formation of significantly predominant NonaCB and octachlorobiphenyl (OctaCB) isomers was attributed to lower energy principles and to the 90° dihedral angles of two aromatic rings which prevented the hydrodechlorination at ortho-positions. When the number of chlorine atoms is not more than 7, the steric effect supports the formation of predominant PCB isomers having chlorines at four ortho-positions. During the dechlorination of tetrachlorobiphenyl (TetraCB) formed to generate monochlorobiphenyl (MonoCB) isomers, the chlorine atoms fully substituted at the ortho-positions have to be successively removed, with the first two dechlorinations preferentially occurring at the two different benzene rings. This is dissimilar to that of octachloronaphthalene (PCN-75) in which the hydrodechlorination reaction happened preferentially at ortho-position due to the existence of steric effects. The opposite roles of the steric effect in ortho-position between PCB-209 and PCN-75 might be due to the difference of the π-conjugated plane caused by the dihedral angle of 90° and 0° of the two aromatic rings. Copyright © 2015 Elsevier Ltd. All rights reserved.

Mechanically driven phase separation and corresponding microhardness change in Cu60Zr20Ti20 bulk metallic glass

DEFF Research Database (Denmark)

Cao, Q.P.; Li, J.F.; Zhou, Y.H.

2005-01-01

Rolling deformation of bulk Cu60Zr20Ti20 metallic glass has been performed at cryogenic temperature. The specimens exhibit excellent ductility, and are rolled up to 97% reduction in thickness without fracture. Crystallization is suppressed during the deformation, however, phase separation is obse...... is observed in the glassy matrix when the thickness reduction exceeds 89%. Once the phase separation occurs, the microhardness of the specimen increases drastically, indicating the existence of work hardening by severe plastic deformation of the metallic glass.......Rolling deformation of bulk Cu60Zr20Ti20 metallic glass has been performed at cryogenic temperature. The specimens exhibit excellent ductility, and are rolled up to 97% reduction in thickness without fracture. Crystallization is suppressed during the deformation, however, phase separation...

PCB 28 metabolites elimination kinetics in human plasma on a real case scenario: Study of hydroxylated polychlorinated biphenyl (OH-PCB) metabolites of PCB 28 in a highly exposed German Cohort.

Science.gov (United States)

Quinete, Natalia; Esser, André; Kraus, Thomas; Schettgen, Thomas

2017-07-05

Polychlorinated biphenyls (PCBs) are suspected of carcinogenic, neurotoxic and immunotoxic effects in animals and humans. Although background levels of PCBs have been slowly decreased after their ban, they are still among the most persistent and ubiquitous pollutants in the environment, remaining the subject of great concern. PCB 28 is a trichlorinated PCB found in high concentrations not only in human plasma but also in indoor air in Europe, yet little is known about its metabolic pathway and potential metabolites in humans. The present study aims to elucidate the kinetics of metabolite formation and elimination by analyzing four hydroxylated PCBs (OH-PCBs) in human plasma as potential metabolites of the PCB 28 congener. For this purpose, the study was conducted in plasma samples of highly PCB-exposed individuals (N=268), collected from 2010 to 2014 as a representation of a real case scenario with longitudinal data. OH-PCBs have been predicted, synthesized in the course of this study and further identified and quantitated in human plasma. This is the first time that previously unknown PCB 28 metabolites have been measured in human plasma and half-lives have been estimated for PCB metabolites, which could then provide further understanding in the toxicological consequences of exposure to PCBs in humans. Copyright © 2017 Elsevier B.V. All rights reserved.

Modeling size effects on fatigue life of a zirconium-based bulk metallic glass under bending

International Nuclear Information System (INIS)

Yuan Tao; Wang Gongyao; Feng Qingming; Liaw, Peter K.; Yokoyama, Yoshihiko; Inoue, Akihisa

2013-01-01

A size effect on the fatigue-life cycles of a Zr 50 Cu 30 Al 10 Ni 10 (at.%) bulk metallic glass has been observed in the four-point-bending fatigue experiment. Under the same bending-stress condition, large-sized samples tend to exhibit longer fatigue lives than small-sized samples. This size effect on the fatigue life cannot be satisfactorily explained by the flaw-based Weibull theories. Based on the experimental results, this study explores possible approaches to modeling the size effects on the bending-fatigue life of bulk metallic glasses, and proposes two fatigue-life models based on the Weibull distribution. The first model assumes, empirically, log-linear effects of the sample thickness on the Weibull parameters. The second model incorporates the mechanistic knowledge of the fatigue behavior of metallic glasses, and assumes that the shear-band density, instead of the flaw density, has significant influence on the bending fatigue-life cycles. Promising predictive results provide evidence of the potential validity of the models and their assumptions.

Hot Embossing of Zr-Based Bulk Metallic Glass Micropart Using Stacked Silicon Dies

Directory of Open Access Journals (Sweden)

Zhijing Zhu

2015-01-01

Full Text Available We demonstrated hot embossing of Zr65Cu17.5Ni10Al7.5 bulk metallic glass micropart using stacked silicon dies. Finite element simulation was carried out, suggesting that it could reduce the stress below 400 MPa in the silicon dies and enhance the durability of the brittle silicon dies when using varying load mode (100 N for 60 s and then 400 N for 60 s compared with using constant load mode (200 N for 120 s. A micropart with good appearance was fabricated under the varying load, and no silicon die failure was observed, in agreement with the simulation. The amorphous state of the micropart was confirmed by differential scanning calorimeter and X-ray diffraction, and the nanohardness and Young’s modulus were validated close to those of the as-cast BMG rods by nanoindentation tests. The results proved that it was feasible to adopt the varying load mode to fabricate three-dimensional Zr-based bulk metallic glass microparts by hot embossing process.

Formation and properties of two-phase bulk metallic glasses by spark plasma sintering

Energy Technology Data Exchange (ETDEWEB)

Xie Guoqiang, E-mail: xiegq@imr.tohoku.ac.jp [Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan); Louzguine-Luzgin, D.V. [WPI Advanced Institute for Materials Research, Tohoku University, Sendai 980-8577 (Japan); Inoue, Akihisa [Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan); WPI Advanced Institute for Materials Research, Tohoku University, Sendai 980-8577 (Japan)

2011-06-15

Research highlights: > Two-phase bulk metallic glasses with high strength and good soft magnetic properties as well as satisfying large-size requirements were produced by spark plasma sintering. > Effects of sintering temperature on thermal stability, microstructure, mechanical and magnetic properties were investigated. > Densified samples were obtained by the spark plasma sintering at above 773 K. - Abstract: Using a mixture of the gas-atomized Ni{sub 52.5}Nb{sub 10}Zr{sub 15}Ti{sub 15}Pt{sub 7.5} and Fe{sub 73}Si{sub 7}B{sub 17}Nb{sub 3} glassy alloy powders, we produced the two-phase bulk metallic glass (BMG) with high strength and good soft magnetic properties as well as satisfying large-size requirements by the spark plasma sintering (SPS) process. Two kinds of glassy particulates were homogeneously dispersed each other. With an increase in sintering temperature, density of the produced samples increased, and densified samples were obtained by the SPS process at above 773 K. Good bonding state among the Ni- and Fe-based glassy particulates was achieved.

Preparation, thermal stability, and magnetic properties of Fe-Zr-Mo-W-B bulk metallic glass

International Nuclear Information System (INIS)

Liu, D.Y.; Sun, W.S.; Wang, A.M.; Zhang, H.F.; Hu, Z.Q.

2004-01-01

A bulk metallic glass (BMG) cylinder of Fe 60 Co 8 Zr 10 Mo 5 W 2 B 15 with a diameter of 1.5 mm was prepared by copper mould casting of industrial raw materials. The amorphous state and the crystallization behavior were investigated by X-ray diffraction (XRD). The thermal stability parameters, such as glass transition temperature (T g ), crystallization temperature (T x ), supercooled liquid region (ΔT x ) between T g and T x , and reduced glass transition temperature T rg (T g /T m ) were measured by differential scanning calorimetry (DSC) to be 891, 950, 59 K, and 0.62, respectively. The crystallization process took place through a single stage, and involved crystallization of the phases α-Fe, ZrFe 2 , Fe 3 B, MoB 2 , Mo 2 FeB 2 , and an unknown phase, as determined by X-ray analysis of the sample annealed for 1.5 ks at 1023 K, 50 K above the DSC peak temperature of crystallization. Moessbauer spectroscopy was studied for this alloy. The spectra exhibit a broadened and asymmetric doublet-like structure that indicated paramagnetic behavior and a fully amorphous structure. α-Fe was found in the amorphous matrix for a cylinder with a diameter of 2.5 mm. The success of synthesis of the Fe-based bulk metallic glass from industrial materials is important for the future progress in research and practical application of new bulk metallic glasses

Developmental Exposure to an Environmental PCB Mixture ...

Science.gov (United States)

Developmental PCB exposure impairs hearing and induces brainstem audiogenic seizures in adult offspring. The degree to which this enhanced susceptibility to seizure is manifest in other brain regions has not been examined. Thus, electrical kindling of the amygdala was used to evaluate the effect of developmental exposure to an environmentally relevant PCB mixture on seizure susceptibility in the rat. Female Long-Evans rats were dosed orally with 0 or 6 mg/kg/day of the PCB mixture dissolved in corn oil vehicle during the perinatal period. On postnatal day (PND) 21, pups were weaned, and two males from each litter were randomly selected for the kindling study. As adults, the male rats were implanted bilaterally with electrodes in the basolateral amygdala. For each animal, afterdischarge (AD) thresholds in the amygdala were determined on the first day of testing followed by once daily stimulation at a standard 200 µA stimulus intensity until three stage 5 generalized seizures (GS) ensued. Developmental PCB exposure did not affect the AD threshold or total cumulative AD duration, but PCB exposure did increase the latency to behavioral manifestations of seizure propagation. PCB exposed animals required significantly more stimulations to reach stage 2 seizures compared to control animals, indicating an attenuated focal (amygdala) excitability. A delay in kindling progression from a focally stimulated limbic site stands in contrast to our previous finding of increase

21 CFR 109.30 - Tolerances for polychlorinated biphenyls (PCB's).

Science.gov (United States)

2010-04-01

... Tolerances for polychlorinated biphenyls (PCB's). (a) Polychlorinated biphenyls (PCB's) are toxic, industrial chemicals. Because of their widespread, uncontrolled industrial applications, PCB's have become a persistent... unavoidable environmental or industrial contaminants are established for a sufficient period of time following...

40 CFR 761.63 - PCB household waste storage and disposal.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false PCB household waste storage and..., AND USE PROHIBITIONS Storage and Disposal § 761.63 PCB household waste storage and disposal. PCB... to manage municipal or industrial solid waste, or in a facility with an approval to dispose of PCB...

Cavitation instability in bulk metallic glasses

Directory of Open Access Journals (Sweden)

Dai L.H.

2015-01-01

Full Text Available Recent experiments have shown that fracture surfaces of bulk metallic glasses (BMGs usually exhibit an intriguing nanoscale corrugation like fractographic feature mediated by nanoscale void formation. We attribute the onset of this nanoscale corrugation to TTZs (tension transformation zones mediated cavitation. In our recent study, the spall experiments of Zr-based BMG using a single-stage light gas gun were performed. To uncover the mechanisms of the spallation damage nucleation and evolution, the samples were designed to be subjected to dynamic tensile loadings of identical amplitude but with different durations by making use of the multi-stress pulse and the double-flyer techniques. It is clearly revealed that the macroscopic spall fracture in BMGs originates from the nucleation, growth and coalescence of micro-voids. Then, a microvoid nucleation model of BMGs based on free volume theory is proposed, which indicates that the nucleation of microvoids at the early stage of spallation in BMGs is resulted from diffusion and coalescence of free volume. Furthermore, a theoretical model of void growth in BMGs undergoing remote dynamic hydrostatic tension is developed. The critical condition of cavitation instability is obtained. It is found that dynamic void growth in BMGs can be well controlled by a dimensionless inertial number characterizing the competition between intrinsic and extrinsic time scales. To unveil the atomic-level mechanism of cavitation, a systematic molecular dynamics (MD simulation of spallation behaviour of a binary metallic glass with different impact velocities was performed. It is found that micro-void nucleation is determined TTZs while the growth is controlled by shear transformation zones (STZs at atomic scale.

Fatigue and corrosion of a Pd-based bulk metallic glass in various environments

Energy Technology Data Exchange (ETDEWEB)

Watanabe, L.Y. [East Los Angeles College, Monterey Park, CA 91754 (United States); Roberts, S.N. [Keck Laboratory of Materials Science, California Institute of Technology, Pasadena, CA 91125 (United States); Baca, N. [Department of Chemistry and Biochemistry, California State University Northridge, Northridge, CA 91330 (United States); Wiest, A. [Naval Surface Warfare Center, Norco, CA (United States); Garrett, S.J. [Department of Chemistry and Biochemistry, California State University Northridge, Northridge, CA 91330 (United States); Conner, R.D., E-mail: rdconner@csun.edu [Department of Manufacturing Systems Engineering and Management, California State University Northridge, 18111 Nordhoff St., Mail Code 8295, Northridge, CA 91330 (United States)

2013-10-15

Bulk metallic glasses (BMGs) possess attractive properties for biomedical applications, including high strength, hardness and corrosion resistance, and low elastic modulus. In this study, we conduct rotating beam fatigue tests on Pd{sub 43}Ni{sub 10}Cu{sub 27}P{sub 20} bulk metallic glass in air and Eagle's medium (EM) and measure the corrosive resistance of the alloy by submersion in acidic and basic electrolytes. Fatigue results are compared to those of commonly used biometals in EM. Rotating beam fatigue tests conducted in air and in Eagle's medium show no deterioration in fatigue properties in this potentially corrosive environment out to 10{sup 7} cycles. A specimen size effect is revealed when comparing fatigue results to those of a similar alloy of larger minimum dimensions. Corrosion tests show that the alloy is not affected by highly basic (NaOH) or saline (NaCl) solutions, nor in EM, and is affected by chlorinated acidic solutions (HCl) to a lesser extent than other commonly used biometals. Corrosion in HCl initiates with selective leaching of late transition metals, followed by dissolution of Pd. - Highlights: • Fatigue limit of 600 MPa with no deterioration when exposed to Eagle's medium. • Fatigue shows sample size effect. • Pd-based BMG is unaffected by saline or strong basic solutions. • Pd-based BMG is substantially more resistant to chlorinated acids than CoCrMo, 316 L Stainless, or Ti6Al4V alloys. • Corrosion shows selective leaching of late transition metals, followed by Pd and P.

Roles of Co element in Fe-based bulk metallic glasses utilizing industrial FeB alloy as raw material

Directory of Open Access Journals (Sweden)

Shouyuan Wang

2017-08-01

Full Text Available A series of Fe-based bulk metallic glasses were fabricated by a conventional copper mold casting method using a kind of Fe-B industrial raw alloy. It is found that Fe-B-Y-Nb bulk metallic glass with 3 at% of Co addition possesses the best glass forming ability, thermal stability, hardness, magnetic property and anti-corrosion property. The hardness test result indicates a synchronically trend with glass-forming ability parameters. The excellent glass-forming ability and a combination of good mechanical and functional properties suggest that the alloys in this work might be good candidates for commercial use.

Bulk and microscale compressive behavior of a Zr-based metallic glass

International Nuclear Information System (INIS)

Lai, Y.H.; Lee, C.J.; Cheng, Y.T.; Chou, H.S.; Chen, H.M.; Du, X.H.; Chang, C.I.; Huang, J.C.; Jian, S.R.; Jang, J.S.C.; Nieh, T.G.

2008-01-01

Micropillars with diameters of 3.8, 1 and 0.7 μm were fabricated from a two-phase Zr-based metallic glass using focus ion beam (FIB), and then tested in compression at strain rates from 1 x 10 -4 to 1 x 10 -2 s -1 . The apparent yield strength of the micropillars ranges from 1992 to 2972 MPa, or 25-86% increase over that of the bulk specimens. This strength increase can be rationalized by the Weibull statistics for brittle materials

‘… a metal conducts and a non-metal doesn't’

Science.gov (United States)

Edwards, P. P.; Lodge, M. T. J.; Hensel, F.; Redmer, R.

2010-01-01

In a letter to one of the authors, Sir Nevill Mott, then in his tenth decade, highlighted the fact that the statement ‘… a metal conducts, and a non-metal doesn’t’ can be true only at the absolute zero of temperature, T=0 K. But, of course, experimental studies of metals, non-metals and, indeed, the electronic and thermodynamic transition between these canonical states of matter must always occur above T=0 K, and, in many important cases, for temperatures far above the absolute zero. Here, we review the issues—theoretical and experimental—attendant on studies of the metal to non-metal transition in doped semiconductors at temperatures close to absolute zero (T=0.03 K) and fluid chemical elements at temperatures far above absolute zero (T>1000 K). We attempt to illustrate Mott’s insights for delving into such complex phenomena and experimental systems, finding intuitively the dominant features of the science, and developing a coherent picture of the different competing electronic processes. A particular emphasis is placed on the idea of a ‘Mott metal to non-metal transition’ in the nominally metallic chemical elements rubidium, caesium and mercury, and the converse metallization transition in the nominally non-metal elements hydrogen and oxygen. We also review major innovations by D. A. Goldhammer (Goldhammer 1913 Dispersion und absorption des lichtes) and K. F. Herzfeld (Herzfeld 1927 Phys. Rev. 29, 701–705. (doi:10.1103/PhysRev.29.701)) in a pre-quantum theory description of the metal–non-metal transition, which emphasize the pivotal role of atomic properties in dictating the metallic or non-metallic status of the chemical elements of the periodic table under ambient and extreme conditions; a link with Pauling’s ‘metallic orbital’ is also established here. PMID:20123742

Kartlegging av PCB i sedimenter fra Indre Sørfjord

OpenAIRE

Skei, J.; Klungsøyr, J.

1990-01-01

Som følge av forhøyede nivåer av PCB i fiskelever innerst i Sørfjorden er det gjennomført en sedimentundersøkelse for om mulig å finne kilden til PCB. Det ble ikke registrert høye nivåer av PCB i sedimentene. Høyeste konsentrasjoner ble målt i munningen av Eitrheimsvågen. Analyser av trafooljer brukt i Tyssedalsområdet viste spor av PCB. Statens forurensningstilsyn (SFT)

Influence of Co addition on the magnetocaloric effect of FeCoSiAlGaPCB amorphous alloys

OpenAIRE

Franco García, Victorino; Borrego Moro, Josefa María; Conde Amiano, Alejandro

2006-01-01

The FeCoSiAlGaPCB alloys can be prepared as bulk amorphous materials, with outstanding mechanical properties and increased electrical resistivity. These features can be beneficial for their application as a magnetic refrigerant. The influence of Co addition on the magnetic entropy change of the alloy has been studied. This compositional modification displaces the temperature of the peak entropy change closer to room temperature, but reduces the refrigerant capacity of the material...

Comparison of mechanical behavior between bulk and ribbon Cu-based metallic glasses

International Nuclear Information System (INIS)

Jiang, W.H.; Liu, F.X.; Wang, Y.D.; Zhang, H.F.; Choo, H.; Liaw, P.K.

2006-01-01

As-cast bulk and as-spun ribbon Cu 60 Zr 30 Ti 10 metallic glasses were characterized using differential-scanning calorimetry and instrumented nanoindentation. Two alloys show a significant difference in the amount of free volume, which is attributed to the difference in a cooling rate, while exhibiting a similar serrated plastic flow. Atomic-force-microscopy observations demonstrate the pile-ups containing shear bands around the indents in both alloys. The as-cast bulk alloy has higher hardness and elastic modulus than the as-spun ribbon alloy. The difference in the strengths of two alloys may be related to the different amount of free volume. The strength seems to be more sensitive to a cooling rate during solidification than the plastic-flow behavior in the Cu 60 Zr 30 Ti 10

Polychlorinated biphenyls (PCB 101, PCB 153 and PCB 180) alter leptin signaling and lipid metabolism in differentiated 3T3-L1 adipocytes

International Nuclear Information System (INIS)

Ferrante, Maria C.; Amero, Paola; Santoro, Anna; Monnolo, Anna; Simeoli, Raffaele; Di Guida, Francesca; Mattace Raso, Giuseppina; Meli, Rosaria

2014-01-01

Non-dioxin-like polychlorinated biphenyls (NDL-PCBs) are highly lipophilic environmental contaminants that accumulate in lipid-rich tissues, such as adipose tissue. Here, we reported the effects induced by PCBs 101, 153 and 180, three of the six NDL-PCBs defined as indicators, on mature 3T3-L1 adipocytes. We observed an increase in lipid content, in leptin gene expression and a reduction of leptin receptor expression and signaling, when cells were exposed to PCBs, alone or in combination. These modifications were consistent with the occurrence of “leptin-resistance” in adipose tissue, a typical metabolic alteration related to obesity. Therefore, we investigated how PCBs affect the expression of pivotal proteins involved in the signaling of leptin receptor. We evaluated the PCB effect on the intracellular pathway JAK/STAT, determining the phosphorylation of STAT3, a downstream activator of the transcription of leptin gene targets, and the expression of SOCS3 and PTP1B, two important regulators of leptin resistance. In particular, PCBs 153 and 180 or all PCB combinations induced a significant reduction in pSTAT3/STAT3 ratio and an increase in PTP1B and SOCS3, evidencing an additive effect. The impairment of leptin signaling was associated with the reduction of AMPK/ACC pathway activation, leading to the increase in lipid content. These pollutants were also able to increase the transcription of inflammatory cytokines (IL-6 and TNFα). It is worthy to note that the PCB concentrations used are comparable to levels detectable in human adipose tissue. Our data strongly support the hypothesis that NDL-PCBs may interfere with the lipid metabolism contributing to the development of obesity and related diseases. - Highlights: • NDL-PCBs alter lipid content and metabolism in 3T3-L1 adipocytes. • Impairment of leptin signaling was induced by NDL-PCBs. • NDL-PCBs reduce AMPK and ACC activation. • NDL-PCBs induce the synthesis of pro-inflammatory cytokine by

Polychlorinated biphenyls (PCB 101, PCB 153 and PCB 180) alter leptin signaling and lipid metabolism in differentiated 3T3-L1 adipocytes

Energy Technology Data Exchange (ETDEWEB)

Ferrante, Maria C. [Department of Veterinary Medicine and Animal Productions, Federico II University of Naples, Via Delpino 1, 80137 Naples (Italy); Amero, Paola; Santoro, Anna [Department of Pharmacy, Federico II University of Naples, Via Montesano 49, 80131 Naples (Italy); Monnolo, Anna [Department of Veterinary Medicine and Animal Productions, Federico II University of Naples, Via Delpino 1, 80137 Naples (Italy); Simeoli, Raffaele; Di Guida, Francesca [Department of Pharmacy, Federico II University of Naples, Via Montesano 49, 80131 Naples (Italy); Mattace Raso, Giuseppina, E-mail: mattace@unina.it [Department of Pharmacy, Federico II University of Naples, Via Montesano 49, 80131 Naples (Italy); Meli, Rosaria, E-mail: meli@unina.it [Department of Pharmacy, Federico II University of Naples, Via Montesano 49, 80131 Naples (Italy)

2014-09-15

Non-dioxin-like polychlorinated biphenyls (NDL-PCBs) are highly lipophilic environmental contaminants that accumulate in lipid-rich tissues, such as adipose tissue. Here, we reported the effects induced by PCBs 101, 153 and 180, three of the six NDL-PCBs defined as indicators, on mature 3T3-L1 adipocytes. We observed an increase in lipid content, in leptin gene expression and a reduction of leptin receptor expression and signaling, when cells were exposed to PCBs, alone or in combination. These modifications were consistent with the occurrence of “leptin-resistance” in adipose tissue, a typical metabolic alteration related to obesity. Therefore, we investigated how PCBs affect the expression of pivotal proteins involved in the signaling of leptin receptor. We evaluated the PCB effect on the intracellular pathway JAK/STAT, determining the phosphorylation of STAT3, a downstream activator of the transcription of leptin gene targets, and the expression of SOCS3 and PTP1B, two important regulators of leptin resistance. In particular, PCBs 153 and 180 or all PCB combinations induced a significant reduction in pSTAT3/STAT3 ratio and an increase in PTP1B and SOCS3, evidencing an additive effect. The impairment of leptin signaling was associated with the reduction of AMPK/ACC pathway activation, leading to the increase in lipid content. These pollutants were also able to increase the transcription of inflammatory cytokines (IL-6 and TNFα). It is worthy to note that the PCB concentrations used are comparable to levels detectable in human adipose tissue. Our data strongly support the hypothesis that NDL-PCBs may interfere with the lipid metabolism contributing to the development of obesity and related diseases. - Highlights: • NDL-PCBs alter lipid content and metabolism in 3T3-L1 adipocytes. • Impairment of leptin signaling was induced by NDL-PCBs. • NDL-PCBs reduce AMPK and ACC activation. • NDL-PCBs induce the synthesis of pro-inflammatory cytokine by

Glass Formation, Chemical Properties and Surface Analysis of Cu-Based Bulk Metallic Glasses

Directory of Open Access Journals (Sweden)

Akihisa Inoue

2011-04-01

Full Text Available This paper reviews the influence of alloying elements Mo, Nb, Ta and Ni on glass formation and corrosion resistance of Cu-based bulk metallic glasses (BMGs. In order to obtain basic knowledge for application to the industry, corrosion resistance of the Cu–Hf–Ti–(Mo, Nb, Ta, Ni and Cu–Zr–Ag–Al–(Nb bulk glassy alloy systems in various solutions are reported in this work. Moreover, X-ray photoelectron spectroscopy (XPS analysis is performed to clarify the surface-related chemical characteristics of the alloy before and after immersion in the solutions; this has lead to a better understanding of the correlation between the surface composition and the corrosion resistance.

Sampling methodology and PCB analysis

International Nuclear Information System (INIS)

Dominelli, N.

1995-01-01

As a class of compounds PCBs are extremely stable and resist chemical and biological decomposition. Diluted solutions exposed to a range of environmental conditions will undergo some preferential degradation and the resulting mixture may differ considerably from the original PCB used as insulating fluid in electrical equipment. The structure of mixtures of PCBs (synthetic compounds prepared by direct chlorination of biphenyl with chlorine gas) is extremely complex and presents a formidable analytical problem, further complicated by the presence of PCBs as contaminants in oils to soils to water. This paper provides some guidance into sampling and analytical procedures; it also points out various potential problems encountered during these processes. The guidelines provided deal with sample collection, storage and handling, sample stability, laboratory analysis (usually gas chromatography), determination of PCB concentration, calculation of total PCB content, and quality assurance. 1 fig

Gender difference in walleye PCB concentrations persists following remedial dredging

Science.gov (United States)

Madenjian, Charles P.; Jude, David J.; Rediske, Richard R.; O'Keefe, James P.; Noguchi, George E.

2009-01-01

Eleven male walleyes (Sander vitreus) and 10 female walleyes from the Saginaw Bay (Lake Huron) population were caught during the spawning run at Dow Dam (Midland, Michigan) in the Tittabawassee River during April 1996, and individual whole-fish polychlorinated biphenyl (PCB) determinations were made. Total PCB concentrations averaged 7.95 and 3.17??mg/kg for males and females, respectively. As part of the Natural Resource Damage Assessment remediation process, contaminated sediments from the Saginaw River, the main tributary to Saginaw Bay, were removed during 2000 and 2001. Total PCB concentrations of 10 male and 10 female walleyes caught at Dow Dam during April 2007 averaged 1.58 and 0.55??mg/kg, respectively. Thus, dredging of the Saginaw River appeared to be effective in reducing PCB concentrations of Saginaw Bay adult walleyes, as both males and females decreased in PCB concentration by more than 80% between 1996 and 2007. However, the ratio of male PCB concentration to female PCB concentration did not decline between 1996 and 2007. This persistent gender difference in PCB concentrations was apparently due to a gender difference in habitat utilization coupled with a persistent spatial gradient in prey fish PCB concentrations from the Saginaw River to Lake Huron.

Novel non-platinum metal catalyst material

DEFF Research Database (Denmark)

2014-01-01

The present invention relates to a novel non-platinum metal catalyst material for use in low temperature fuel cells and electrolysers and to fuel cells and electrolysers comprising the novel non-platinum metal catalyst material. The present invention also relates to a novel method for synthesizing...... the novel non-platinum metal catalyst material....

Non-destructive identification of unknown minor phases in polycrystalline bulk alloys using three-dimensional X-ray diffraction

Energy Technology Data Exchange (ETDEWEB)

Yang, Yiming, E-mail: yangyiming1988@outlook.com [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Xu, Liang [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Wang, Yudan; Du, Guohao [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China); Yang, Sam [Commonwealth Scientific and Industrial Research Organization, Melbourne, VIC 3168 (Australia); Xiao, Tiqiao, E-mail: tqxiao@sinap.ac.cn [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China); University of Chinese Academy of Sciences, Beijing 100049 (China)

2017-02-15

Minor phases make considerable contributions to the mechanical and physical properties of metals and alloys. Unfortunately, it is difficult to identify unknown minor phases in a bulk polycrystalline material using conventional metallographic methods. Here, a non-destructive method based on three-dimensional X-ray diffraction (3DXRD) is developed to solve this problem. Simulation results demonstrate that this method is simultaneously able to identify minor phase grains and reveal their positions, orientations and sizes within bulk alloys. According to systematic simulations, the 3DXRD method is practicable for an extensive sample set, including polycrystalline alloys with hexagonal, orthorhombic and cubic minor phases. Experiments were also conducted to confirm the simulation results. The results for a bulk sample of aluminum alloy AA6061 show that the crystal grains of an unexpected γ-Fe (austenite) phase can be identified, three-dimensionally and nondestructively. Therefore, we conclude that the 3DXRD method is a powerful tool for the identification of unknown minor phases in bulk alloys belonging to a variety of crystal systems. This method also has the potential to be used for in situ observations of the effects of minor phases on the crystallographic behaviors of alloys. - Highlights: •A method based on 3DXRD is developed for identification of unknown minor phase. •Grain position, orientation and size, is simultaneously acquired. •A systematic simulation demonstrated the applicability of the proposed method. •Experimental results on a AA6061 sample confirmed the practicability of the method.

Parametric Design and Rapid Prototyping of Installation Box for Vehicle Terminal PCB

Directory of Open Access Journals (Sweden)

Wang Xingxing

2016-01-01

Full Text Available Installation box for vehicle terminal PCB (Printed Circuit Board was took as research object, which is encountered in the process of project developing. Vehicle terminal PCB in actual development process was set as an example, point cloud data were acquired by three coordinate measuring method; Imageware software was used to reconstruct the vehicle terminal PCB model, basic size parameters of vehicle terminal PCB can be got and then design parameters of installation box for vehicle terminal PCB can be determined. Design of the installation box for vehicle terminal PCB was completed based on Solidworks software, then 3D modeling and 2D drawing of installation box for vehicle terminal PCB was gained. Up Plus 2 rapid prototype machine was used to manufacture installation box for vehicle terminal PCB rapidly based on 3D printing technology, then prototype of installation box for vehicle terminal PCB was obtained. It is of certain engineering significant for single (small amount manufacturing of installation box for general PCB.

Economical weight loss program for PCB-contaminated ballasts

International Nuclear Information System (INIS)

Day, B.

1995-01-01

A PCB (Polychlorinated Biphenyls) reduction process for PCB-contaminated ballasts was described. The process was developed by such organizations and programs as PCB Containment Technology Inc, and the Contech Ballast Reduction Program, and was claimed to include waste reduction of lighting ballasts down to their smallest PCB contaminated components. Particular attention was paid to the two most contaminated main components, i.e. the capacitor and the tar potting material. Development of the process and the government's role and participation therein was explained. The process of ballast reduction was said to utilize the old 'Reduce, Reuse and Recycle' theory; it was considered to be a cost effective waste reduction, recycling, and auditing alternative to incineration of PCBs

Formation of hydroxyapatite on Ti-coated Ti-Zr-Cu-Pd bulk metallic glass

International Nuclear Information System (INIS)

Qin, F.X.; Wang, X.M.; Wada, T.; Xie, G.Q.; Asami, K.; Inoue, A.

2009-01-01

In this research, Ti coating was conducted on Ti 40 Zr 10 Cu 36 Pd 14 bulk metallic glass (BMG) in order to increase the formation rate of hydroxyapatite layer. The formation behavior of bone-like hydroxyapatite on Ti-coated and uncoated Ti 40 Zr 10 Cu 36 Pd 14 bulk metallic glasses (BMGs) was studied. The surface morphology of Ti-coated and uncoated Ti 40 Zr 10 Cu 36 Pd 14 BMG was investigated by scanning electron microscopy and energy dispersive X-ray spectroscopy. The results revealed that the alkali pretreatment in 5 M NaOH solution at 60degC for 24 h had a beneficial effect on the formation of porous sodium titanate on Ti-coated Ti 40 Zr 10 Cu 36 Pd 14 BMG. A bone-like hydroxyapatite layer was able to form on the alkali-treated Ti-coated Ti 40 Zr 10 Cu 36 Pd 14 BMG after a short-time immersion in simulated body fluid (SBF). On the contrary, hydroxyapatite formation was not observed on the uncoated Ti 40 Zr 10 Cu 36 Pd 14 BMG after the same chemical treatments. (author)

Dioxins, DL-PCB and NDL-PCB accumulation profiles in livers from sheep and cattle reared in North-western Italy.

Science.gov (United States)

Benedetto, A; Brizio, P; Guaraldo, P; Stella, C; Cappa, C; Baioni, E; Spalenza, V; Nebbia, C; Abete, M C

2016-06-01

Products of animal origin represent the main route of human exposure to dioxins and dioxin-like PCBs (DL-compounds). Recently, concerns have been raised about ovine products, particularly the liver, in which relatively high levels of DL-compounds have been reported. We surveyed ovine and bovine livers in areas with no known sources of dioxin or DL-PCB contamination, in order to assess accumulation patterns for both DL-compounds and non-DL (NDL-) PCBs. None of the ovine and bovine samples exceeded the current Maximum Limits (MLs) for DL-compounds. Liver DL-compound TEQ concentrations were up to 5-fold higher in sheep than in cows. No statistically significant differences in total NDL-PCBs levels were found. The main contributors to TEQ levels were the Penta- and Hexa-chlorinated PCDFs and PCB 126. The results confirm the increased bioaccumulation in ovine liver towards specific DL-compounds even in ewes reared in areas with no known sources of PCDD/Fs or DL-PCBs contamination. Copyright © 2016 Elsevier Ltd. All rights reserved.

Laboratory study of PCB transport from primary sources to settled dust

Science.gov (United States)

Transport of house dust and Arizona Test Dust on polychlorinated biphenyl (PCB)-containing panels and PCB-free panels was investigated in a 30-m3 stainless steel chamber. The PCB-containing panels were aluminum sheets coated with a PCB-spiked, oil-based primer or two-part polysul...

40 CFR 761.269 - Sampling liquid PCB remediation waste.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Sampling liquid PCB remediation waste..., AND USE PROHIBITIONS Cleanup Site Characterization Sampling for PCB Remediation Waste in Accordance with § 761.61(a)(2) § 761.269 Sampling liquid PCB remediation waste. (a) If the liquid is single phase...

An overlooked environmental issue? A review of the inadvertent formation of PCB-11 and other PCB congeners and their occurrence in consumer products and in the environment.

Science.gov (United States)

Vorkamp, Katrin

2016-01-15

Polychlorinated biphenyls (PCBs) are banned from production and use in most countries as they are persistent organic pollutants (POPs) of concern for environment and health. Recent research has pointed at a new environment issue resulting from the inadvertent formation of PCBs in certain processes, in particular the pigment production. PCB-11 is a major by-product in these processes, but PCB-28, PCB-52, PCB-77 as well as the nonachlorinated PCBs and PCB-209 have been found in pigments and consumer products as well. In addition to environmental emissions via point sources, in particular related to industrial and municipal wastewater, atmospheric transport seems to be important for the global distribution of PCB-11. Thus, PCB-11 has also been detected in the polar regions. Worldwide air concentrations appear relatively uniform, but maxima have been found in urban and industrialised areas. Data on the uptake and accumulation of PCB-11 in the food chain are still inconclusive: Although food web studies do not show biomagnification, PCB-11 has been detected in humans. The human exposure might originate from the direct contact to consumer products as well as from the omnipresence of PCB-11 in the environment. Copyright © 2015 Elsevier B.V. All rights reserved.

Influence of a combination of two tetrachlorobiphenyl congeners (PCB 47; PCB 77) on thyroid status, choline acetyltransferase (ChAT) activity, and short- and long-term memory in 30-day-old Sprague-Dawley rats

International Nuclear Information System (INIS)

Donahue, Douglas A.; Dougherty, Edward J.; Meserve, Lee A.

2004-01-01

The important role of thyroid hormones in growth and development, maintenance of body temperature, digestion, cardiac function, and normal brain development can be disrupted by environmental contaminants like polychlorinated biphenyls (PCB). Polychlorinated biphenyls are environmental contaminants that are widespread, persistent, lipophilic, and bioaccumulate through food webs, concentrating in adipose tissue. Placental and lactational PCB exposure of offspring causes metabolic and endocrine disruptions including hypothyroxinemia, spatial learning and memory deficits, neurochemical and neurobehavioral alterations, and reproductive problems. Previous studies in our lab using the individual congeners PCB 47 (2,2',4,4'-tetrachlorobiphenyl, ortho-substituted) and PCB 77 (3,3',4,4'-tetrachlorobiphenyl, non-ortho-substituted) have demonstrated alterations in thyroid hormone levels, alterations in brain choline acetyltransferase (ChAT) activity, and spatial learning deficits. In the present study, pregnant Sprague-Dawley rats were fed a diet with or without a mixture of PCB 47/77 at 1.25 ppm, 12.5 ppm or 25.0 ppm (w/w). Rat pups were swum in the Morris water maze four times a day on days 21-29 in order for the animals to learn the position of a submerged fixed platform. A probe test was run on day 24 (30 min after last swim) for short-term memory, and on day 29 (24 h after the last swim) for long-term memory after removal of the platform. Time spent in the quadrant previously containing the platform was recorded. Rats were decapitated on day 30, serum collected and frozen at -20 deg. ChAT activity was measured radiometrically in basal forebrain and hippocampus. All PCB-treated animals experienced a depression in both triiodothyronine (T 3 ) and thyroxine (T 4 ). The present study found that all doses of PCB depressed ChAT activity in hippocampus with no significant alteration in the basal forebrain. In PCB-treated animals, short-term memory showed a trend toward

Review on progressive microforming of bulk metal parts directly using sheet metals (Keynote Paper

Directory of Open Access Journals (Sweden)

Fu M.W.

2015-01-01

Full Text Available Due to the ubiquitous trend of product miniaturization, energy saving and weight reduction, micro/meso-scale parts have been widely used in many industrial clusters. Micromanufacturing processes for production of such micro/meso-scale parts are thus critically needed. Microforming, as one of these micro manufacturing processes, is a promising process and thus got many explorations and researches. Compared with the research on size effect affected deformation behaviours, less attention has been paid to the process development for mass production of micro-parts. The product quality and fabrication productivity of micro-parts depend on the involved process chain. To address the difficulty in handling and transporting of the micro-sized workpiece, development of a progressive microforming process for directly fabricating bulk micro-parts using sheet metals seems quite promising as it avoids or facilitates billet handling, transportation, positioning, and ejection in the process chain. In this paper, an intensive review on the latest development of progressive microforming technologies is presented. First of all, the paper summarizes the characteristic of progressive microforming directly using sheet metal. The size effect-affected deformation behaviour and the dimensional accuracy, deformation load, ductile fracture, and the surface finish of the microformed parts by progressive microforming using sheet metals are then presented. Finally, some research issues from the implementation of mass production perspective are also discussed.

Effect of seafood mediated PCB exposure on desaturase activity and PUFA profile in Faroese septuagenarians.

Science.gov (United States)

Tøttenborg, Sandra Søgaard; Choi, Anna L; Bjerve, Kristian S; Weihe, Pal; Grandjean, Philippe

2015-07-01

Polychlorinated biphenyl (PCB) exposure may affect serum concentrations of polyunsaturated fatty acids (PUFAs) by inhibiting desaturases ∆5 and ∆6 that drive their synthesis from precursor fatty acids. Such changes in the composition of fatty acids may affect cardiovascular disease risk, which is thought to increase at elevated PCB exposures. This population-based cross-sectional study examined 712 Faroese men and women aged 70-74 years. The serum phospholipid fraction of fasting blood samples was used to determine the PUFA profile, including linoleic acid, dihomo-γ-linolenic acid, arachidonic acid, eicosatrienoic acid, and other relevant fatty acids. Ratios between precursor and metabolite fatty acids were used as proxies for ∆5 and ∆6 desaturase activity. Tertiles of serum-PCB concentrations were used in multiple regression analyses to determine the association between the exposure and desaturase activity. In multiple regression models, PCB exposure was inversely related to the estimated Δ6 desaturase activity resulting in accumulation of precursor fatty acids and decrease in the corresponding product PUFAs. A positive association between PCB and Δ5 desaturation was also found. A relative increase in EA was also observed, though only in the third tertile of PCB exposure. Non-linear relationships between the exposure and the desaturase activity were not found. Consuming fish and seafood may not be translated into beneficial fatty acid profiles if the diet simultaneously causes exposure to PCBs. Although the desaturase estimates were likely influenced by dietary intakes of product PUFAs, the association between PCB exposure and ∆6 desaturase activity is plausible and may affect cardiovascular disease risk. Copyright © 2015 Elsevier Inc. All rights reserved.

Electrical analysis of high dielectric constant insulator and metal gate metal oxide semiconductor capacitors on flexible bulk mono-crystalline silicon

KAUST Repository

Ghoneim, Mohamed T.

2015-06-01

We report on the electrical study of high dielectric constant insulator and metal gate metal oxide semiconductor capacitors (MOSCAPs) on a flexible ultra-thin (25 μm) silicon fabric which is peeled off using a CMOS compatible process from a standard bulk mono-crystalline silicon substrate. A lifetime projection is extracted using statistical analysis of the ramping voltage (Vramp) breakdown and time dependent dielectric breakdown data. The obtained flexible MOSCAPs operational voltages satisfying the 10 years lifetime benchmark are compared to those of the control MOSCAPs, which are not peeled off from the silicon wafer. © 2014 IEEE.

Measurement of hydroxylated PCB metabolites for Slovakia maternal blood serums

Energy Technology Data Exchange (ETDEWEB)

Park, J.S.; Athanasiadou, M; Bergman, A. [Stockholm Univ., Stockholm (Sweden); Charles, J.; Zhao, G.; Hertz-Picciotto, I. [California Univ., Sacramento, CA (United States); Petrik, J.; Kocan, A; Trnovec, T. [Bratislava Inst. of Preventive and Clinical Medicine, Bratislava (Slovakia)

2005-07-01

Although it is known that polychlorinated biphenyls (PCBs) have adverse impacts on human health, it is not clear if human health impacts are caused by the PCBs or their related hydroxylated (OH) PCB metabolite compounds. This study measured OH-PCB metabolites in the maternal blood serum specimens from the Svidnik and Michalovce areas in eastern Slovakia where PCBs were intensively produced and inadequately disposed. The aim of the study was to characterize and quantify levels of specific OH-PCB metabolites in Slovakian maternal serums exposed to high environmental PCB levels. All specimens were analyzed for PCBs, and a subset of the samples was analyzed for OH-PCB metabolites. The Wallenburg blood extraction method was adopted to separate the OH-PCBs from the blood serums. Final eluates and calibration standards were spiked with PCB209 as an injection standard before gas chromatography (GC) analysis. OH-PCBs in the samples range from 75{+-}9 per cent to 101{+-}11 per cent. Median concentrations of OH-PCB metabolites of Michalovce samples were approximately twice as high as for the Svidnik samples. Concentrations of OH-PCBs of Michalovce blood samples were comparable to samples obtained from northern Canadian female Inuit and Faroe Island females, and were considered to be among the highest OH-PCB concentrations obtained in human blood. It was concluded that further research is needed to understand the placental transfer of OH-PCBs to the fetus, as well as epidemiological approaches to determine the relationship between the exposure of OH-PCB metabolites and child development. 12 refs., 2 figs.

Carbon nanotubes grown on bulk materials and methods for fabrication

Science.gov (United States)

Menchhofer, Paul A [Clinton, TN; Montgomery, Frederick C [Oak Ridge, TN; Baker, Frederick S [Oak Ridge, TN

2011-11-08

Disclosed are structures formed as bulk support media having carbon nanotubes formed therewith. The bulk support media may comprise fibers or particles and the fibers or particles may be formed from such materials as quartz, carbon, or activated carbon. Metal catalyst species are formed adjacent the surfaces of the bulk support material, and carbon nanotubes are grown adjacent the surfaces of the metal catalyst species. Methods employ metal salt solutions that may comprise iron salts such as iron chloride, aluminum salts such as aluminum chloride, or nickel salts such as nickel chloride. Carbon nanotubes may be separated from the carbon-based bulk support media and the metal catalyst species by using concentrated acids to oxidize the carbon-based bulk support media and the metal catalyst species.

Biological treatment processes for PCB contaminated soil at a site in Newfoundland

International Nuclear Information System (INIS)

Punt, M.; Cooper, D.; Velicogna, D.; Mohn, W.; Reimer, K.; Parsons, D.; Patel, T.; Daugulis, A.

2002-01-01

SAIC Canada is conducting a study under the direction of a joint research and development contract between Public Works and Government Services Canada and Environment Canada to examine the biological options for treating PCB contaminated soil found at a containment cell at a former U.S. Military Base near Stephenville, Newfoundland. In particular, the study examines the feasibility of using indigenous microbes for the degradation of PCBs. The first phase of the study involved the testing of the microbes in a bioreactor. The second phase, currently underway, involves a complete evaluation of possible microbes for PCB degradation. It also involves further study into the biological process options for the site. Suitable indigenous and non-indigenous microbes for PCB dechlorination and biphenyl degradation are being identified and evaluated. In addition, the effectiveness and economics of microbial treatment in a conventional bioreactor is being evaluated. The conventional bioreactor used in this study is the two-phase partitioning bioreactor (TPPB) using a biopile process. Results thus far will be used to help Public Works and Government Services Canada to choose the most appropriate remedial technology. Preliminary results suggest that the use of soil classification could reduce the volume of soil requiring treatment. The soil in the containment cell contains microorganisms that could grow in isolation on biphenyl, naphthalene and potentially Aroclor 1254. Isolated native microbes were inoculated in the TPPB for growth. The TPPB was also run successfully under anaerobic conditions. Future work will involve lab-scale evaluation of microbes for PCB dechlorination and biphenyl degradation using both indigenous and non-indigenous microbes. The next phase of study may also involve field-scale demonstration of treatment methods. 2 refs., 3 tabs., 5 figs

Biocompatibility study on Ni-free Ti-based and Zr-based bulk metallic glasses

Energy Technology Data Exchange (ETDEWEB)

Li, T.H. [Institute of Material Science and Engineering, National Central University, Taoyuan, Taiwan (China); Wong, P.C. [Department of Biomedical Engineering, National Yang-Ming University, Taipei, Taiwan (China); Chang, S.F. [Department of Mechanical Engineering, National Central University, Taoyuan, Taiwan (China); Tsai, P.H. [Institute of Material Science and Engineering, National Central University, Taoyuan, Taiwan (China); Jang, J.S.C., E-mail: jscjang@ncu.edu.tw [Institute of Material Science and Engineering, National Central University, Taoyuan, Taiwan (China); Department of Mechanical Engineering, National Central University, Taoyuan, Taiwan (China); Huang, J.C. [Department of Materials and Optoelectronic Science, National Sun Yat-Sen University, Kaohsiung, Taiwan (China)

2017-06-01

Safety and reliability are crucial issues for medical instruments and implants. In the past few decays, bulk metallic glasses (BMGs) have drawn attentions due to their superior mechanical properties, good corrosion resistance, antibacterial and good biocompatibility. However, most Zr-based and Ti-based BMGs contain Ni as an important element which is prone to human allergy problem. In this study, the Ni-free Ti-based and Zr-based BMGs, Ti{sub 40}Zr{sub 10}Cu{sub 36}Pd{sub 14}, and Zr{sub 48}Cu{sub 36}Al{sub 8}Ag{sub 8}, were selected for systematical evaluation of their biocompatibility. Several biocompatibility tests, co-cultural with L929 murine fibroblast cell line, were carried out on these two BMGs, as well as the comparison samples of Ti6Al4V and pure Cu. The results in terms of cellular adhesion, cytotoxicity, and metallic ion release affection reveal that the Ti{sub 40}Zr{sub 10}Cu{sub 36}Pd{sub 14} BMG and Ti6Al4V exhibit the optimum biocompatibility; cells still being attached on the petri dish with good adhesion and exhibiting the spindle shape after direct contact test. Furthermore, the Ti{sub 40}Zr{sub 10}Cu{sub 36}Pd{sub 14} BMG showed very low Cu ion release level, in agreement with the MTT results. Based on the current findings, it is believed that Ni-free Ti-based BMG can act as an ideal candidate for medical implant. - Highlight: • Ni-free bulk metallic glass is promising material for medical implants. • Ni-free Ti-based BMG presents similar cellular adhesion as Ti6Al4V. • Ni-free Ti-based BMG shows less cytotoxicity, and metallic ion release than Ti6Al4V.

Serum PCB profiles in Native Americans from Wisconsin based on region, diet, age, and gender: Implications for epidemiology studies

International Nuclear Information System (INIS)

Schaeffer, David J.; Dellinger, John A.; Needham, Larry L.; Hansen, Larry G.

2006-01-01

Background: Different PCB congeners and different mixtures of congeners have been demonstrated to have different biological actions. More complete characterization of congener profiles in exposure sources may assist in predicting health outcomes. Methods: Thirty-six (36) polychlorinated biphenyl (PCB) congeners were measured by gas chromatography isotope-dilution mass spectrometry (IDMS) in 314 serum samples from Native Americans in Wisconsin, Michigan and Minnesota. Five dietary groups were established based on the quantity and species of fish consumed and the waters from which the fish were caught. Multivariate statistical methods were able to resolve gender and dietary differences in PCB homologue and PCB congener patterns. Results: Females had higher proportions of lower chlorinated homologues, including a consistently higher proportion of pentaCB 118. The relative presence of the very labile and volatile PCB 18, above 1% of the total PCB in females from the minimal fish consumption and 'other' groups, suggests possible exposure to PCBs in the atmosphere. The dietary group consuming predatory fishes from Lakes Michigan and Superior had the highest serum concentrations of total PCB (mean of 3.1 ng/ml) and the most distinct congener profile. The two dietary groups least dependent on fishing or fishing mostly from inland lakes (non-Great Lakes) had the lowest total PCB concentrations, both with means of 1.4 ng/ml. Conclusions: These serum PCB concentrations were less than those found in earlier studies of fish consumers in the Great Lakes region and may reflect the decrease in PCBs in these lakes

[Recycle of contaminated scrap metal]: Task 1.3.2, Bulk solids feed system. Topical report, October 1993-- January 1996

International Nuclear Information System (INIS)

1996-07-01

A critical requirement in DOE's efforts to recycle, reuse, and dispose of materials from its decontamination and decommissioning activities is the design of a robust system to process a wide variety of bulk solid feeds. The capability to process bulk solids will increase the range of materials and broaden the application of Catalytic Extraction Processing (CEP). The term bulk solids refers to materials that are more economically fed into the top of a molten metal bath than by submerged injection through a tuyere. Molten Metal Technology, Inc. (MMT) has characterized CEP's ability to process bulk solid feed materials and has achieved significant growth in the size of bulk solid particles compatible with Catalytic Extraction Processing. Parametric experimental studies using various feed materials representative of the components of various DOE waste streams have validated design models which establish the reactor operating range as a function of feed material, mass flow rate, and particle size. MMT is investigating the use of a slurry system for bulk solid addition as it is the most efficient means for injecting soils, sludges, and similar physical forms into a catalytic processing unit. MMT is continuing to evaluate condensed phase product removal systems and alternative energy addition sources to enhance the operating efficiency of bulk solids CEP units. A condensed phase product removal system capable of on-demand product removal has been successfully demonstrated. MMT is also investigating the use of a plasma arc torch to provide supplemental heating during bulk solids processing. This comprehensive approach to bulk solids processing is expected to further improve overall process efficiency prior to the deployment of CEP for the recycle, reuse, and disposal of materials from DOE decontamination and decommissioning Activities

Source determination of highly chlorinated biphenyl isomers in pine needles - Comparison to several PCB preparations

International Nuclear Information System (INIS)

Wyrzykowska, Barbara; Bochentin, Ilona; Hanari, Nobuyasu; Orlikowska, Anna; Falandysz, Jerzy; Yuichi, Horii; Yamashita, Nobuyoshi

2006-01-01

The isomer specific composition of 13 technical PCB formulations of different origin and of pine needles was analyzed using GC/MS and HRGC/HRMS. Nonachlorinated biphenyls were identified in 11 among 13 formulations analyzed, with the highest abundance found for highly chlorinated ones (Aroclors 1268 and 1260, Chlorofen, Sovol, Kanechlors 600 and 500, Delor 106, Clophen A60). Decachlorobiphenyl was identified only in Aroclor 1268, Clophen A60, Aroclor 1260 and Chlorofen, comprising, respectively, 8.9, 2.8, 1.3 and 0.82% of the total bulk of nona- and decaCBs detected. Nona- and decaCB were detected in pine needles in Poland with the highest concentrations found at the sites neighboring to a former production sites of the Polish PCB formulations, while in pine needles collected around the Tokyo Bay nona- and decacCB were detected only in four of 10 sites and the concentrations corresponded to those found at the rural areas of Poland. - Pine needles were suitable as passive samplers for PCBs in air

Flexible thermoelectric generator using bulk legs and liquid metal interconnects for wearable electronics

International Nuclear Information System (INIS)

Suarez, Francisco; Parekh, Dishit P.; Ladd, Collin; Vashaee, Daryoosh; Dickey, Michael D.; Öztürk, Mehmet C.

2017-01-01

Highlights: •Flexible thermoelectric generator (TEG) with bulk legs. •Flexible thermoelectric generator with liquid metal interconnects. •Flexible TEG with potential to match the performance of rigid TEGs. •Flexible TEG for wearable electronics. -- Abstract: Interest in wearable electronics for continuous, long-term health and performance monitoring is rapidly increasing. The reduction in power levels consumed by sensors and electronic circuits accompanied by the advances in energy harvesting methods allows for the realization of self-powered monitoring systems that do not have to rely on batteries. For wearable electronics, thermoelectric generators (TEGs) offer the unique ability to continuously convert body heat into usable energy. For body harvesting, it is preferable to have TEGs that are thin, soft and flexible. Unfortunately, the performances of flexible modules reported to date have been far behind those of their rigid counterparts. This is largely due to lower efficiencies of the thermoelectric materials, electrical or thermal parasitic losses and limitations on leg dimensions posed by the synthesis techniques. In this work, we present an entirely new approach and explore the possibility of using standard bulk legs in a flexible package. Bulk thermoelectric legs cut from solid ingots are far superior to thermoelectric materials synthesized using other techniques. A key enabler of the proposed technology is the use of EGaIn liquid metal interconnects, which not only provide extremely low interconnect resistance but also stretchability with self-healing, both of which are essential for flexible TE modules. The results suggest that this novel approach can finally produce flexible TEGs that have the potential to challenge the rigid TEGs and provide a pathway for the realization of self-powered wearable electronics.

Feasibility of using bulk metallic glass for self-expandable stent applications.

Science.gov (United States)

Praveen Kumar, Gideon; Jafary-Zadeh, Mehdi; Tavakoli, Rouhollah; Cui, Fangsen

2017-10-01

Self-expandable stents are widely used to restore blood flow in a diseased artery segment by keeping the artery open after angioplasty. Despite the prevalent use of conventional crystalline metallic alloys, for example, nitinol, to construct self-expandable stents, new biomaterials such as bulk metallic glasses (BMGs) are being actively pursued to improve stent performance. Here, we conducted a series of analyses including finite element analysis and molecular dynamics simulations to investigate the feasibility of using a prototypical Zr-based BMG for self-expandable stent applications. We model stent crimping of several designs for different percutaneous applications. Our results indicate that BMG-based stents with diamond-shaped crowns suffer from severe localization of plastic deformation and abrupt failure during crimping. As a possible solution, we further illustrate that such abrupt failure could be avoided in BMG-based stents without diamond shape crowns. This work would open a new horizon for a quest toward exploiting superior mechanical and functional properties of metallic glasses to design future stents. © 2016 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 105B: 1874-1882, 2017. © 2016 Wiley Periodicals, Inc.

Bulk metallic glasses and high entropy alloys for reprocessing applications

International Nuclear Information System (INIS)

Kamachi Mudali, U.; Jayaraj, J.

2016-01-01

Recent breakthroughs in materials engineering have generated complex alloys that retain a glassy state in bulk form (bulk metallic glasses or BMGs) via ingot casting. High corrosion resistance is expected for BMGs (amorphous) as they are free from defects associated with the crystalline state such as grain boundaries, dislocations and stacking faults. Compared with conventional alloys containing one or two principal elements, the recently developed HEAs are usually composed of five or more elements with equimolar or near equimolar elemental fractions, which forms single solid solution phase. These HEAs exhibit excellent microstructural stability with better mechanical, wear and corrosion resistance properties as they are essentially single phase. Reprocessing of spent fuel from the fast breeder reactor involves the use of high concentration of (11.5 M) nitric acid under boiling conditions for the dissolution of the fuel. Conventional AISI type 304LSS and nitric acid grade 304L stainless steel would undergo inter-granular corrosion under these conditions and cannot be used for the fabrication of dissolver vessel. Currently titanium is used and zirconium alloys are proposed for future dissolver applications. Thus searching for newer materials with higher corrosion resistance suggests metallic glasses and HEAs for critical components of the dissolver application. Several Zr-based glassy alloys with different microstructural states and Ni-Nb based glassy alloys and TiZrHfNbTa HEA were cast and characterized for microstructure and corrosion resistance in nitric acid medium. From these studies, factors such as the corrosive environment (nitric acid, chloride and fluoride), and the presence of passivating elements in the alloy were emphasized for better corrosion resistance of BMGs and HEA. Attempts were also made to prepare coatings of Zr-and Ni-based glassy alloys on 304LSS by laser based deposition technique and their corrosion properties were evaluated. (author)

Measurement of PCB concentrations in waters using a biomonitoring programme

International Nuclear Information System (INIS)

Mast, P.G.

1993-01-01

The book describes a PCB biomonitoring programme which was developed for measuring instantaneous PCB concentrations and permits the compilation of PCB action cadastres for different types of waters and subsequent derivation of current trends. Six representative congeners were selected as a basis for the quantitative routine analysis. The fish species bream (abramis brama) and roach (rutilus rutilus) were used as indicators in the PCB biomonitoring programme on account of their distribution and ecological demands. The age and growth rate of each fish destined for analysis was determined so as to ensure that only healthy fish would be used. In both fish species the dorsal musulature with its low scatter of test results and consistent PCB pattern (internal quantification) proved a representative body region. (orig.) [de

Compressive deformation of in situ formed bulk metallic glass composites

Energy Technology Data Exchange (ETDEWEB)

Clausen, B. [Lujan Neutron Science Center, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Lee, S.Y. [Department of Materials Science and Engineering, Iowa State University, Ames, IA 50011 (United States); Ustuendag, E. [Department of Materials Science and Engineering, Iowa State University, Ames, IA 50011 (United States)]. E-mail: ustundag@iastate.edu; Kim, C.P. [Liquidmetal Technologies, Lake Forest, CA 92630 (United States); Brown, D.W. [Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Bourke, M.A.M. [Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States)

2006-02-15

A bulk metallic glass matrix composite with dendc second phase precipitates was investigated using neutron diffraction and self-consistent modeling (SCM) to ascertain its deformation mechanisms. The compressive behavior of both the composite and the second phase (in its monolithic form) were investigated. The diffraction data were compared to the predictions of a new SCM resulting in good agreement. For the first time, this model considered both amorphous and crystalline phases and allowed the calculation of single crystal elastic constants from polycrystalline diffraction data. It was shown that the ductile second phase yielded first upon loading, and this was followed by multiple shear band formation in the matrix, a process which enhanced the ductility of the composite.

Compressive deformation of in situ formed bulk metallic glass composites

International Nuclear Information System (INIS)

Clausen, B.; Lee, S.Y.; Ustuendag, E.; Kim, C.P.; Brown, D.W.; Bourke, M.A.M.

2006-01-01

A bulk metallic glass matrix composite with dendritic second phase precipitates was investigated using neutron diffraction and self-consistent modeling (SCM) to ascertain its deformation mechanisms. The compressive behavior of both the composite and the second phase (in its monolithic form) were investigated. The diffraction data were compared to the predictions of a new SCM resulting in good agreement. For the first time, this model considered both amorphous and crystalline phases and allowed the calculation of single crystal elastic constants from polycrystalline diffraction data. It was shown that the ductile second phase yielded first upon loading, and this was followed by multiple shear band formation in the matrix, a process which enhanced the ductility of the composite

Second amorphous-to-crystalline phase transformation in Cu60Ti20Zr20 bulk metallic glass

DEFF Research Database (Denmark)

Cao, Q.P.; Li, J.F.; Zhang, P.N.

2007-01-01

The second amorphous-to-crystalline phase transformation in Cu60Ti20Zr20 bulk metallic glass was investigated by differential scanning calorimetry and x-ray diffractometry. The difference of the Gibbs free energies between the amorphous phase and the crystalline products during the transformation...

Eco Logic signs deal to destroy Japanese PCB stocks

International Nuclear Information System (INIS)

Anon.

1997-01-01

According to a recent announcement, Eco Logic of Rockwood, Ontario, has entered into a partnership with the Japanese companies Tokyo Boeki and Nippon Sharyo for the destruction of stockpiled PCB materials in Japan, using Eco Logic's non-incineration technology. The deal is reported to be worth about $50 million in revenues to Eco Logic, spread over the next few years. The agreement includes provisions for the Japanese companies to purchase, or manufacture under licence, a number of Eco Logic's gas phase chemical reduction processing units to serve the Japanese market. In exchange for exclusive rights to the Japanese market, Eco Logic will receive license fees and royalties of up to nine per cent for the use of its process. Eco Logic is currently building a demonstration unit under contract with the two Japanese companies. The Japanese PCB waste destruction market is estimated to be worth as much as $400 million. Incineration, the conventional form of disposal, is strongly opposed by local governments

Sexual difference in PCB concentrations of coho salmon (Oncorhynchus kisutch)

Science.gov (United States)

Madenjian, Charles P.; Schrank, Candy S.; Begnoche, Linda J.; Elliott, Robert F.; Quintal, Richard T.

2010-01-01

We determined polychlorinated biphenyl (PCB) concentrations in 35 female coho salmon (Oncorhynchus kisutch) and 60 male coho salmon caught in Lake Michigan (Michigan and Wisconsin, United States) during the fall of 1994 and 1995. In addition, we determined PCB concentrations in the skin-on fillets of 26 female and 19 male Lake Michigan coho salmon caught during the fall of 2004 and 2006. All coho salmon were age-2 fish. These fish were caught prior to spawning, and therefore release of eggs could not account for sexual differences in PCB concentrations because female coho salmon spawn only once during their lifetime. To investigate whether gross growth efficiency (GGE) differed between the sexes, we applied bioenergetics modeling. Results showed that, on average, males were 19% higher in PCB concentration than females, based on the 1994–1995 dataset. Similarly, males averaged a 20% higher PCB concentration in their skin-on fillets compared with females. According to the bioenergetics modeling results, GGE of adult females was less than 1% higher than adult male GGE. Thus, bioenergetics modeling could not explain the 20% higher PCB concentration exhibited by the males. Nonetheless, a sexual difference in GGE remained a plausible explanation for the sexual difference in PCB concentrations.

Hard X-ray PhotoElectron Spectroscopy of transition metal oxides: Bulk compounds and device-ready metal-oxide interfaces

International Nuclear Information System (INIS)

Borgatti, F.; Torelli, P.; Panaccione, G.

2016-01-01

Highlights: • Hard X-ray PhotoElectron Spectroscopy (HAXPES) applied to buried interfaces of systems involving Transition Metal Oxides. • Enhanced contribution of the s states at high kinetic energies both for valence and core level spectra. • Sensitivity to chemical changes promoted by electric field across metal-oxide interfaces in resistive switching devices. - Abstract: Photoelectron spectroscopy is one of the most powerful tool to unravel the electronic structure of strongly correlated materials also thanks to the extremely large dynamic range in energy, coupled to high energy resolution that this form of spectroscopy covers. The kinetic energy range typically used for photoelectron experiments corresponds often to a strong surface sensitivity, and this turns out to be a disadvantage for the study of transition metal oxides, systems where structural and electronic reconstruction, different oxidation state, and electronic correlation may significantly vary at the surface. We report here selected Hard X-ray PhotoElectron Spectroscopy (HAXPES) results from transition metal oxides, and from buried interfaces, where we highlight some of the important features that such bulk sensitive technique brings in the analysis of electronic properties of the solids.

Hard X-ray PhotoElectron Spectroscopy of transition metal oxides: Bulk compounds and device-ready metal-oxide interfaces

Energy Technology Data Exchange (ETDEWEB)

Borgatti, F., E-mail: francesco.borgatti@cnr.it [Istituto per lo Studio dei Materiali Nanostrutturati (ISMN), Consiglio Nazionale delle Ricerche (CNR), via P. Gobetti 101, Bologna I-40129 (Italy); Torelli, P.; Panaccione, G. [Istituto Officina dei Materiali (IOM)-CNR, Laboratorio TASC, Area Science Park, Trieste I-34149 (Italy)

2016-04-15

Highlights: • Hard X-ray PhotoElectron Spectroscopy (HAXPES) applied to buried interfaces of systems involving Transition Metal Oxides. • Enhanced contribution of the s states at high kinetic energies both for valence and core level spectra. • Sensitivity to chemical changes promoted by electric field across metal-oxide interfaces in resistive switching devices. - Abstract: Photoelectron spectroscopy is one of the most powerful tool to unravel the electronic structure of strongly correlated materials also thanks to the extremely large dynamic range in energy, coupled to high energy resolution that this form of spectroscopy covers. The kinetic energy range typically used for photoelectron experiments corresponds often to a strong surface sensitivity, and this turns out to be a disadvantage for the study of transition metal oxides, systems where structural and electronic reconstruction, different oxidation state, and electronic correlation may significantly vary at the surface. We report here selected Hard X-ray PhotoElectron Spectroscopy (HAXPES) results from transition metal oxides, and from buried interfaces, where we highlight some of the important features that such bulk sensitive technique brings in the analysis of electronic properties of the solids.

Elastic properties of superconducting bulk metallic glasses; Elastische Eigenschaften von supraleitenden massiven metallischen Glaesern

Energy Technology Data Exchange (ETDEWEB)

Hempel, Marius

2015-07-01

Within the framework of this thesis the elastic properties of a superconducting bulk metallic glass between 10 mK and 300 K were first investigated. In order to measure the entire temperature range, in particular the low temperature part, new experimental techniques were developed. Using an inductive readout scheme for a double paddle oscillator it was possible to determine the internal friction and the relative change of sound velocity of bulk metallic glasses with high precision. This allowed for a detailed comparison of the data with different models. The analysis focuses on the low temperature regime where the properties of glassy materials are governed by atomic tunneling systems as described by the tunneling model. The influence of conduction electrons in the normal conducting state and quasiparticles in the superconducting state of the glass were accounted for in the theoretical description, resulting in a good agreement over a large temperature range between measured data and prediction of the tunneling model. This allowed for a direct determination of the coupling constant between electrons and tunneling systems. In the vicinity of the transition temperature Tc the data can only be described if a modified distribution function of the tunneling parameters is applied.

Memory phenomenon in a lanthanum based bulk metallic glass

Energy Technology Data Exchange (ETDEWEB)

Zhou, Ye [School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, 639798 (Singapore); Huang, Wei Min, E-mail: mwmhuang@ntu.edu.sg [School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, 639798 (Singapore); Zhao, Yong [School of Chemistry and Chemical Engineering, Jiangsu University, 301 Xuefu Road, Zhenjiang 212013 (China); Ding, Zhen [School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, 639798 (Singapore); Li, Yan [School of Materials Science and Engineering, Beihang University, Beijing 100191 (China); Tor, Shu Beng; Liu, Erjia [School of Mechanical and Aerospace Engineering, Nanyang Technological University, 50 Nanyang Avenue, 639798 (Singapore)

2016-07-05

In this paper, we experimentally investigate two memory phenomena in a lanthanum based bulk metallic glass (BMG). While the temperature memory effect (TME) is not found by differential scanning calorimeter (DSC) test, shape recovery is observed in samples indented at both low and high temperatures. In terms of shape memory related characteristics, this BMG shares some features of shape memory alloys (SMAs) due to its metal nature, and some other features of shape memory polymers (SMPs) owing to its glassy–rubbery transition. The formation of protrusion in the polished sample after heating to super-cooled liquid region (SCLR) indicates that surface tension is not a necessarily positive contributor for shape recovery. Release of internal elastic stress is concluded as the major player. Although the amorphous nature of BMGs enables for storing appreciable amount of internal elastic stress upon deformation, without the presence of cross-linker as in typical SMPs, the shape recovery in BMGs is rather limited. - Highlights: • Experimental investigation of shape recovery in BMG. • Surface tension is not the major reason for shape recovery in BMG. • Release of internal stress is the major contributor for shape recovery. • Comparison of shape memory features of BMG with other shape memory materials.

Memory phenomenon in a lanthanum based bulk metallic glass

International Nuclear Information System (INIS)

Zhou, Ye; Huang, Wei Min; Zhao, Yong; Ding, Zhen; Li, Yan; Tor, Shu Beng; Liu, Erjia

2016-01-01

In this paper, we experimentally investigate two memory phenomena in a lanthanum based bulk metallic glass (BMG). While the temperature memory effect (TME) is not found by differential scanning calorimeter (DSC) test, shape recovery is observed in samples indented at both low and high temperatures. In terms of shape memory related characteristics, this BMG shares some features of shape memory alloys (SMAs) due to its metal nature, and some other features of shape memory polymers (SMPs) owing to its glassy–rubbery transition. The formation of protrusion in the polished sample after heating to super-cooled liquid region (SCLR) indicates that surface tension is not a necessarily positive contributor for shape recovery. Release of internal elastic stress is concluded as the major player. Although the amorphous nature of BMGs enables for storing appreciable amount of internal elastic stress upon deformation, without the presence of cross-linker as in typical SMPs, the shape recovery in BMGs is rather limited. - Highlights: • Experimental investigation of shape recovery in BMG. • Surface tension is not the major reason for shape recovery in BMG. • Release of internal stress is the major contributor for shape recovery. • Comparison of shape memory features of BMG with other shape memory materials.

Characterization of bulk and shear properties of basmati and non-basmati rice flour.

Science.gov (United States)

Jan, Shumaila; Ghoroi, Chinmay; Saxena, Dharmesh Chandra

2018-01-01

Flours are often unstable in relation to their flow performance, which is evident when a free-flowing material ceases to flow and the processing, handling, and production parameters depend on the inherent powder characteristics and their bulk behaviour. The present study was conducted to compare the flowability of basmati and non-basmati rice flour affecting bulk handling, which could be related to its particle size, shape and surface roughness (measured by atomic force microscopy) as well as bulk and shear properties, depending upon the processing conditions. Particle size (171.1-171.9 μm) of both samples was not significantly different. However, the flowability of the non-basmati rice flour was significantly affected by its particle shape (circularity 0.487), surface roughness (124.23 nm) and compressibility (25.32%) in comparison to basmati rice flour (circularity 0.653, surface roughness 113.59 nm and compressibility 21.09%), making it more cohesive than basmati rice flour. Also, basic flow energy was significantly higher in non-basmati flour, thus requiring more energy (147.54 mJ) to flow than basmati rice flour (130.15 mJ). Overall, flowability was analysed by applying three different pressures (3, 6 and 9 kPa), among which non-basmati rice flour was found to be less flowable (flow function coefficient (FFC) 2.33 at 9 kPa) in comparison to basmati (FFC 3.35 at 9 kPa), making bulk handling difficult. This study could be useful in designing processing equipment, hoppers and silos for rice flour handling. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Treating PCB contaminated light ballasts

International Nuclear Information System (INIS)

Day, B.

1995-01-01

Development and salient features of CON TECH PCB, a light ballast reduction process to allow PCB waste owners to best utilize storage space for the long-term regulated storage of PCBs, or to prepare them for final destruction and to reduce destruction costs, was reviewed. The essence of the process is ballast splitting, i.e. the breaking of the ballast and removing the capacitor containing the toxic PCBs. The work is done in a specially fitted mobile processing unit, thus reducing the storage requirements by better than 50 per cent. Details of the process and some cost and storage facility estimates were provided

Mono-, di-, and trichlorinated biphenyls (PCB 1-PCB 39) in the indoor air of office rooms and their relevance on human blood burden.

Science.gov (United States)

Kraft, M; Sievering, S; Grün, L; Rauchfuss, K

2018-05-01

Exposure to polychlorinated biphenyls (PCBs) from indoor air can lead to a significant increase in lower chlorinated congeners in human blood. Lower chlorinated congeners with short biological half-lives can exhibit an indirect genotoxic potential via their highly reactive metabolites. However, little is known about their occurrence in indoor air and, therefore, about the effects of possible exposure to these congeners. We analyzed all mono-, di-, and trichlorinated biphenyls in the indoor air of 35 contaminated offices, as well as in the blood of the 35 individuals worked in these offices for a minimum of 2 years. The median concentration of total PCB in the indoor air was 479 ng/m 3 . The most prevalent PCBs in the indoor air samples were the trichlorinated congeners PCB 31, PCB 18, and PCB 28, with median levels of 39, 31, and 26 ng/m 3 , respectively. PCB 8 was the most prevalent dichlorinated congener (median: 9.1 ng/m 3 ). Monochlorinated biphenyls were not detected in relevant concentrations. In the blood samples, the most abundant congener was PCB 28; nearly 90% of all mono-, di-, and trichlorinated congeners were attributed to this congener (median: 12 ng/g blood lipid). © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Toxicological profile of ultrapure 2,2',3,4,4',5,5'-heptachlorbiphenyl (PCB 180) in adult rats.

Science.gov (United States)

Viluksela, Matti; Heikkinen, Päivi; van der Ven, Leo T M; Rendel, Filip; Roos, Robert; Esteban, Javier; Korkalainen, Merja; Lensu, Sanna; Miettinen, Hanna M; Savolainen, Kari; Sankari, Satu; Lilienthal, Hellmuth; Adamsson, Annika; Toppari, Jorma; Herlin, Maria; Finnilä, Mikko; Tuukkanen, Juha; Leslie, Heather A; Hamers, Timo; Hamscher, Gerd; Al-Anati, Lauy; Stenius, Ulla; Dervola, Kine-Susann; Bogen, Inger-Lise; Fonnum, Frode; Andersson, Patrik L; Schrenk, Dieter; Halldin, Krister; Håkansson, Helen

2014-01-01

PCB 180 is a persistent non-dioxin-like polychlorinated biphenyl (NDL-PCB) abundantly present in food and the environment. Risk characterization of NDL-PCBs is confounded by the presence of highly potent dioxin-like impurities. We used ultrapure PCB 180 to characterize its toxicity profile in a 28-day repeat dose toxicity study in young adult rats extended to cover endocrine and behavioral effects. Using a loading dose/maintenance dose regimen, groups of 5 males and 5 females were given total doses of 0, 3, 10, 30, 100, 300, 1000 or 1700 mg PCB 180/kg body weight by gavage. Dose-responses were analyzed using benchmark dose modeling based on dose and adipose tissue PCB concentrations. Body weight gain was retarded at 1700 mg/kg during loading dosing, but recovered thereafter. The most sensitive endpoint of toxicity that was used for risk characterization was altered open field behavior in females; i.e. increased activity and distance moved in the inner zone of an open field suggesting altered emotional responses to unfamiliar environment and impaired behavioral inhibition. Other dose-dependent changes included decreased serum thyroid hormones with associated histopathological changes, altered tissue retinoid levels, decreased hematocrit and hemoglobin, decreased follicle stimulating hormone and luteinizing hormone levels in males and increased expression of DNA damage markers in liver of females. Dose-dependent hypertrophy of zona fasciculata cells was observed in adrenals suggesting activation of cortex. There were gender differences in sensitivity and toxicity profiles were partly different in males and females. PCB 180 adipose tissue concentrations were clearly above the general human population levels, but close to the levels in highly exposed populations. The results demonstrate a distinct toxicological profile of PCB 180 with lack of dioxin-like properties required for assignment of WHO toxic equivalency factor. However, PCB 180 shares several toxicological

Hypervelocity impact on Zr51Ti5Ni10Cu25Al9 bulk metallic glass

International Nuclear Information System (INIS)

Zheng, W.; Huang, Y.J.; Pang, B.J.; Shen, J.

2011-01-01

Highlights: → Hypervelocity impact experiments were performed on a bulk metallic glass. → Morphology of the bullet hole presents three different regions. → The post-impact samples keep glassy structure. → Mechanical properties of the post-impact samples were studied by nanoindentation. → Mechanical properties of the post-impact samples were discussed by free-volume model. - Abstract: In this study, the hypervelocity impact experiments were performed on Zr 51 Ti 5 Ni 10 Cu 25 Al 9 bulk metallic glass using a two-stage light gas gun. The morphologies of the bullet holes exhibit three different regions: melting area, vein-pattern area, and radiating core feature area, suggesting that various regions experience different stress states during the hypervelocity impact. For the post-impact samples, the nano-hardness increases and plastic deformability decreases both with the increase in the distance from the bullet hole and with the decrease in the impact velocity, which is discussed by means of spherical stress wave theory and free-volume model.

Bioavailability of 2,3',4,4',5-pentachlorobiphenyl (PCB118) and 2,2',5,5'-tetrachlorobiphenyl (PCB52) from soils using a rat model and a physiologically based extraction test

International Nuclear Information System (INIS)

Pu Xinzhu; Lee, Linda S.; Galinsky, Raymond E.; Carlson, Gary P.

2006-01-01

The bioavailability of coplanar 2,3',4,4',5-pentachlorobiphenyl (PCB118) and nonplanar 2,2',5,5'-tetrachlorobiphenyl (PCB52) from soils representing a range in organic carbon (OC), clay content and pH were investigated using an in vivo rat model and an in vitro physiologically based extraction test (PBET) to assess the role of soil and chemical properties on bioavailabilty. Affinity to soil and persistence of PCBs have been shown to increase with increasing soil organic carbon (OC) content, PCB chlorination, and PCB coplanarity. In the in vivo tests for both PCB118 and PCB52, the AUCs following iv injection were significantly higher than the AUCs for all soil groups, indicating that the soil matrix can reduce the absolute bioavailability of PCB118 and PCB52. However, no significant differences were detected between soils of different properties. In the in vitro PBET, significant differences in the mobilization of PCB118 and PCB52 were observed among soils, and PCBs had the least mobilization from the soil with the highest OC content consistent with hydrophobic partitioning theory. Also, significantly less PCB118 was mobilized relative to PCB52 in the PBET assay, showing the potential impact of spatial orientation and chlorine content on bioavailability. No correlation between the in vitro PBET and the in vivo rat model was observed for the PCBs. Although the in vitro PBET and related assays may serve as an indicator of bioavailability, it is likely to underestimate what can be released from a soil in an in vivo assay

Direct band gap electroluminescence from bulk germanium at room temperature using an asymmetric fin type metal/germanium/metal structure

Energy Technology Data Exchange (ETDEWEB)

Wang, Dong, E-mail: wang.dong.539@m.kyushu-u.ac.jp; Maekura, Takayuki; Kamezawa, Sho [Interdisciplinary Graduate School of Engineering Sciences, Kyushu University, 6-1 Kasuga-koen, Kasuga, Fukuoka 816-8580 (Japan); Yamamoto, Keisuke; Nakashima, Hiroshi [Art, Science and Technology Center for Cooperative Research, Kyushu University, 6-1 Kasuga-koen, Kasuga, Fukuoka 816-8580 (Japan)

2015-02-16

We demonstrated direct band gap (DBG) electroluminescence (EL) at room temperature from n-type bulk germanium (Ge) using a fin type asymmetric lateral metal/Ge/metal structure with TiN/Ge and HfGe/Ge contacts, which was fabricated using a low temperature (<400 °C) process. Small electron and hole barrier heights were obtained for TiN/Ge and HfGe/Ge contacts, respectively. DBG EL spectrum peaked at 1.55 μm was clearly observed even at a small current density of 2.2 μA/μm. Superlinear increase in EL intensity was also observed with increasing current density, due to superlinear increase in population of elections in direct conduction band. The efficiency of hole injection was also clarified.

High-entropy bulk metallic glasses as promising magnetic refrigerants

International Nuclear Information System (INIS)

Huo, Juntao; Huo, Lishan; Li, Jiawei; Men, He; Wang, Xinmin; Chang, Chuntao; Wang, Jun-Qiang; Li, Run-Wei; Inoue, Akihisa

2015-01-01

In this paper, the Ho 20 Er 20 Co 20 Al 20 RE 20 (RE = Gd, Dy, and Tm) high-entropy bulk metallic glasses (HE-BMGs) with good magnetocaloric properties are fabricated successfully. The HE-BMGs exhibit a second-order magnetic phase transition. The peak of magnetic entropy change (ΔS M pk ) and refrigerant capacity (RC) reaches 15.0 J kg −1 K −1 and 627 J kg −1 at 5 T, respectively, which is larger than most rare earth based BMGs. The heterogeneous nature of glasses also contributes to the large ΔS M pk and RC. In addition, the magnetic ordering temperature, ΔS M pk and RC can be widely tuned by alloying different rare earth elements. These results suggest that the HE-BMGs are promising magnetic refrigerant at low temperatures

Ti-based bulk metallic glass with high cold workability at room temperature

International Nuclear Information System (INIS)

Park, J.M.; Park, J.S.; Kim, J.H.; Lee, M.H.; Kim, D.H.; Kim, W.T.

2005-01-01

The cold workability of Ti-based bulk metallic glasses (BMGs) have been investigated. Ti 45 Zr 16 Be 20 Cu 10 Ni 9 BMG with a large compressive plastic strain of 4.7% shows a high cold workability, i.e. total reduction ratio of 50% by cold rolling at room temperature. The multiple shear bands formed during rolling are effective in enhancing the plasticity. The cold rolled Ti 45 Zr 16 Be 20 Cu 10 Ni 9 BMG (reduction ratio: 30%) exhibits a large plastic strain of ∝14%. (orig.)

Flame spray synthesis under a non-oxidizing atmosphere: Preparation of metallic bismuth nanoparticles and nanocrystalline bulk bismuth metal

Energy Technology Data Exchange (ETDEWEB)

Grass, Robert N.; Stark, Wendelin J. [Institute for Chemical and Bioengineering, ETH Zuerich (Switzerland)], E-mail: wendelin.stark@chem.ethz.ch

2006-10-15

Metallic bismuth nanoparticles of over 98% purity were prepared by a modified flame spray synthesis method in an inert atmosphere by oxygen-deficient combustion of a bismuth-carboxylate based precursor. The samples were characterized by X-ray diffraction, thermal analysis and scanning electron microscopy confirming the formation of pure, crystalline metallic bismuth nanoparticles. Compression of the as-prepared powder resulted in highly dense, nanocrystalline pills with strong electrical conductivity and bright metallic gloss.

Case study of a non-destructive treatment method for the remediation of military structures containing polychlorinated biphenyl contaminated paint.

Science.gov (United States)

Saitta, Erin K H; Gittings, Michael J; Novaes-Card, Simone; Quinn, Jacqueline; Clausen, Christian; O'Hara, Suzanne; Yestrebsky, Cherie L

2015-08-01

Restricted by federal regulations and limited remediation options, buildings contaminated with paint laden with polychlorinated biphenyls (PCBs) have high costs associated with the disposal of hazardous materials. As opposed to current remediation methods which are often destructive and a risk to the surrounding environment, this study suggests a non-metal treatment system (NMTS) and a bimetallic treatment system (BTS) as versatile remediation options for painted industrial structures including concrete buildings, and metal machine parts. In this field study, four areas of a discontinued Department of Defense site were treated and monitored over 3 weeks. PCB levels in paint and treatment system samples were analyzed through gas chromatography/electron capture detection (GC-ECD). PCB concentrations were reduced by 95 percent on painted concrete and by 60-97 percent on painted metal with the majority of the PCB removal occurring within the first week of application. Post treatment laboratory studies including the utilization of an activated metal treatment system (AMTS) further degraded PCBs in BTS and NMTS by up to 82 percent and 99 percent, respectively, indicating that a two-step remediation option is viable. These findings demonstrate that the NMTS and BTS can be an effective, nondestructive, remediation process for large painted structures, allowing for the reuse or sale of remediated materials that otherwise may have been disposed. Copyright © 2015 Elsevier Ltd. All rights reserved.

Resveratrol via sirtuin-1 downregulates RE1-silencing transcription factor (REST) expression preventing PCB-95-induced neuronal cell death

International Nuclear Information System (INIS)

Guida, Natascia; Laudati, Giusy; Anzilotti, Serenella; Secondo, Agnese; Montuori, Paolo; Di Renzo, Gianfranco; Canzoniero, Lorella M.T.; Formisano, Luigi

2015-01-01

Resveratrol (3,5,4′-trihydroxystilbene) (RSV), a polyphenol widely present in plants, exerts a neuroprotective function in several neurological conditions; it is an activator of class III histone deacetylase sirtuin1 (SIRT1), a crucial regulator in the pathophysiology of neurodegenerative diseases. By contrast, the RE1-silencing transcription factor (REST) is involved in the neurotoxic effects following exposure to polychlorinated biphenyl (PCB) mixture A1254. The present study investigated the effects of RSV-induced activation of SIRT1 on REST expression in SH-SY5Y cells. Further, we investigated the possible relationship between the non-dioxin-like (NDL) PCB-95 and REST through SIRT1 to regulate neuronal death in rat cortical neurons. Our results revealed that RSV significantly decreased REST gene and protein levels in a dose- and time-dependent manner. Interestingly, overexpression of SIRT1 reduced REST expression, whereas EX-527, an inhibitor of SIRT1, increased REST expression and blocked RSV-induced REST downregulation. These results suggest that RSV downregulates REST through SIRT1. In addition, RSV enhanced activator protein 1 (AP-1) transcription factor c-Jun expression and its binding to the REST promoter gene. Indeed, c-Jun knockdown reverted RSV-induced REST downregulation. Intriguingly, in SH-SY5Y cells and rat cortical neurons the NDL PCB-95 induced necrotic cell death in a concentration-dependent manner by increasing REST mRNA and protein expression. In addition, SIRT1 knockdown blocked RSV-induced neuroprotection in rat cortical neurons treated with PCB-95. Collectively, these results indicate that RSV via SIRT1 activates c-Jun, thereby reducing REST expression in SH-SY5Y cells under physiological conditions and blocks PCB-95-induced neuronal cell death by activating the same SIRT1/c-Jun/REST pathway. - Highlights: • Resveratrol via SIRT1/c-Jun downregulates REST mRNA and protein in SH-SY5Y cells. • Non-dioxin-like (NDL) PCB-95 is cytotoxic to

Resveratrol via sirtuin-1 downregulates RE1-silencing transcription factor (REST) expression preventing PCB-95-induced neuronal cell death

Energy Technology Data Exchange (ETDEWEB)

Guida, Natascia [IRCSS SDN, Naples 80131 (Italy); Laudati, Giusy [Division of Pharmacology, Department of Neuroscience, Reproductive and Dentistry Sciences, School of Medicine, “Federico II” University of Naples, Via Pansini, 5, 80131 Naples (Italy); Anzilotti, Serenella [IRCSS SDN, Naples 80131 (Italy); Secondo, Agnese [Division of Pharmacology, Department of Neuroscience, Reproductive and Dentistry Sciences, School of Medicine, “Federico II” University of Naples, Via Pansini, 5, 80131 Naples (Italy); Montuori, Paolo [Department of Public Health, ‘Federico II’ University of Naples, Naples (Italy); Di Renzo, Gianfranco [Division of Pharmacology, Department of Neuroscience, Reproductive and Dentistry Sciences, School of Medicine, “Federico II” University of Naples, Via Pansini, 5, 80131 Naples (Italy); Canzoniero, Lorella M.T. [Division of Pharmacology, Department of Neuroscience, Reproductive and Dentistry Sciences, School of Medicine, “Federico II” University of Naples, Via Pansini, 5, 80131 Naples (Italy); Division of Pharmacology, Department of Science and Technology, University of Sannio, Via Port' Arsa 11, 82100 Benevento (Italy); Formisano, Luigi, E-mail: cformisa@unisannio.it [Division of Pharmacology, Department of Neuroscience, Reproductive and Dentistry Sciences, School of Medicine, “Federico II” University of Naples, Via Pansini, 5, 80131 Naples (Italy); Division of Pharmacology, Department of Science and Technology, University of Sannio, Via Port' Arsa 11, 82100 Benevento (Italy)

2015-11-01

Resveratrol (3,5,4′-trihydroxystilbene) (RSV), a polyphenol widely present in plants, exerts a neuroprotective function in several neurological conditions; it is an activator of class III histone deacetylase sirtuin1 (SIRT1), a crucial regulator in the pathophysiology of neurodegenerative diseases. By contrast, the RE1-silencing transcription factor (REST) is involved in the neurotoxic effects following exposure to polychlorinated biphenyl (PCB) mixture A1254. The present study investigated the effects of RSV-induced activation of SIRT1 on REST expression in SH-SY5Y cells. Further, we investigated the possible relationship between the non-dioxin-like (NDL) PCB-95 and REST through SIRT1 to regulate neuronal death in rat cortical neurons. Our results revealed that RSV significantly decreased REST gene and protein levels in a dose- and time-dependent manner. Interestingly, overexpression of SIRT1 reduced REST expression, whereas EX-527, an inhibitor of SIRT1, increased REST expression and blocked RSV-induced REST downregulation. These results suggest that RSV downregulates REST through SIRT1. In addition, RSV enhanced activator protein 1 (AP-1) transcription factor c-Jun expression and its binding to the REST promoter gene. Indeed, c-Jun knockdown reverted RSV-induced REST downregulation. Intriguingly, in SH-SY5Y cells and rat cortical neurons the NDL PCB-95 induced necrotic cell death in a concentration-dependent manner by increasing REST mRNA and protein expression. In addition, SIRT1 knockdown blocked RSV-induced neuroprotection in rat cortical neurons treated with PCB-95. Collectively, these results indicate that RSV via SIRT1 activates c-Jun, thereby reducing REST expression in SH-SY5Y cells under physiological conditions and blocks PCB-95-induced neuronal cell death by activating the same SIRT1/c-Jun/REST pathway. - Highlights: • Resveratrol via SIRT1/c-Jun downregulates REST mRNA and protein in SH-SY5Y cells. • Non-dioxin-like (NDL) PCB-95 is cytotoxic to

In Situ Formation of Carbon Nanomaterials on Bulk Metallic Materials

Directory of Open Access Journals (Sweden)

J. Y. Xu

2014-01-01

Full Text Available Carbon nanomaterials were synthesized in situ on bulk 316L stainless steel, pure cobalt, and pure nickel by hybrid surface mechanical attrition treatment (SMAT. The microstructures of the treated samples and the resulted carbon nanomaterials were investigated by SEM and TEM characterizations. Different substrates resulted in different morphologies of products. The diameter of carbon nanomaterials is related to the size of the nanograins on the surface layer of substrates. The possible growth mechanism was discussed. Effects of the main parameters of the synthesis, including the carbon source and gas reactant composition, hydrogen, and the reaction temperature, were studied. Using hybrid SMAT is proved to be an effective way to synthesize carbon nanomaterials in situ on surfaces of metallic materials.

Synthesis and devitrification of high glass-forming ability bulk metallic glasses.

OpenAIRE

Huang, Hong.

2007-01-01

In this thesis, literature on the production, microstructures and properties of bulk metallic glasses (BMG) has been reviewed with particular reference to glass forming ability (GFA) and alloys of the Fe-Zr-B and Zr-based BMG systems. The experimental procedures used in the research are presented and the results for the amorphous Fe80Zr12B8 ribbon and the Zr57Ti5Al10Cu20Ni8, Zr57Nb5Al10Cu20Ni8, Zr53Nb2Al8Cu30Ni7 BMGs are given and discussed. Wedge-shaped ingots of the Zr-based BMGs were produ...

A new method for evaluating structural stability of bulk metallic glasses

Energy Technology Data Exchange (ETDEWEB)

Zhao, Lei; Jia, Haoling [Key Laboratory of Aerospace Materials and Performance, Ministry of Education, School of Materials Science and Engineering, Beihang University, Beijing 100191 (China); Xie, Shenghui; Zeng, Xierong [College of Materials Science and Engineering, Shenzhen University and Shenzhen Key Laboratory of Special Functional Materials, ShenZhen 518060 (China); Zhang, Tao [Key Laboratory of Aerospace Materials and Performance, Ministry of Education, School of Materials Science and Engineering, Beihang University, Beijing 100191 (China); Ma, Chaoli, E-mail: machaoli@buaa.edu.c [Key Laboratory of Aerospace Materials and Performance, Ministry of Education, School of Materials Science and Engineering, Beihang University, Beijing 100191 (China)

2010-08-15

This paper proposed a new method for evaluating the structural stability of bulk metallic glasses (BMGs) based on dilatometric measurements. During heating in the dilatometric experiments, the BMGs expanded continuously with increasing temperature. When the temperature reached the glass transition temperature (T{sub g}), viscous shrinkage occurred due to the viscosity of material becoming lower. Since the inhomogeneous nature of the metallic glasses at atomic level, the processes of rigid expansion and the viscous shrinkage co-exist in a certain temperature region. The expansion stopped completely at a temperature (named T{sub p} here) beyond T{sub g}. The values of the temperature region, {Delta}T{sub gp} = T{sub p} - T{sub g}, and the corresponding time interval ({Delta}t{sub gp}) and the activation energy (E{sub p}) corresponding to the expansion processes, are the reflection of the structural stability of BMGs. Investigating the co-existing processes kinetically and thermodynamically, we can make an insight into the structural stability of metallic glasses. Based on this idea, the thermal expansion behaviors of Mg-, Pd-, Zr-, Ti- and Fe-based BMG were studied, and their structural stability was evaluated by the parameters of {Delta}T{sub gp}, {Delta}t{sub gp} and E{sub p}.

PCB-Based Break-Out Box

Science.gov (United States)

Lee, Jason H.

2011-01-01

Break-out boxes (BOBs) are necessary for all electrical integration/cable checkouts and troubleshooting. Because the price of a BOB is high, and no work can be done without one, often the procedure stops, simply waiting for a BOB. A less expensive BOB would take less time in the integration, testing, and troubleshooting process. The PCB-based BOB works and looks the same as a standard JPL BOB, called Gold Boxes. The only differences between the old BOB and the new PCB-based BOB is that the new one has 80 percent of its circuitry in a printed circuit board. This process reduces the time for fabrication, thus making the BOBs less expensive. Moreover, because of its unique design, the new BOBs can be easily assembled and fixed. About 80 percent of the new PCB-based BOB is in a $22 (at the time of this reporting) custom-designed, yet commercially available PCB. This device has been used successfully to verify that BOB cables were properly made. Also, upon completion, the BOB was beeped out via a multimeter to ensure that all sockets on the connectors were properly connected to the respective banana jack. When compared to the Gold Box BOBs, the new BOB has many advantages. It is much more cost efficient, it delivers equal usability at substantially lower cost of the BOB, and the Gold Box is much heavier when compared to the new BOB. The new BOB is also a bit longer and much more versatile in that connectors are easily changeable and if a banana jack is broken, it can be replaced instead of throwing away an entire BOB.

Laboratory test of source encapsulation for decreasing PCB concentrations

DEFF Research Database (Denmark)

Kolarik, Barbara; Andersen, Helle Vibeke; Markowicz, Pawel

2016-01-01

This study investigates the effect of encapsulation of tertiary PCB sources with PERMASORB™ Adsorber Wallpaper and the surface emissions trap (cTrap) on indoor air concentration of PCBs and on the PCB content in the source. The 40 weeks long laboratory investigation shows reduction of the air...... concentration by approx. 90% for both wallpapers, a level comparable to source removal. The potential for extraction of PCBs from the contaminated materials stays unclear for both wallpapers. The cTrap has shown potential to accumulate PCBs, however the total content of PCB in investigated sources has...... apparently increased. The opposite was observed for the PERMASORB™, where the total PCB content in the sources has decreased, with however only small concentration of PCBs in the wallpaper measured at the end of the experiment....

Effect of Ge addition on mechanical properties and fracture behavior of Cu-Zr-Al bulk metallic glass

International Nuclear Information System (INIS)

Malekan, M.; Shabestari, S.G.; Gholamipour, R.; Seyedein, S.H.

2009-01-01

Effect of the addition of a small amount of Ge on mechanical properties and fracture behavior of Cu 50 Zr 43 Al 7 (at.%) bulk metallic glass were studied. The Cu 50 Zr 43 Al 7 alloy has a surprising glass-forming ability (GFA), and the glassy rods up to 4 mm in diameter can be formed. Partial addition of Ge causes the crystalline phases precipitate in the glassy matrix of (Cu 50 Zr 43 Al 7 ) 100-x Ge x (x = 0, 1, 2) rods with a diameter of 4 mm. In uniaxial compression, Cu 50 Zr 43 Al 7 bulk metallic glass exhibit high strength of 1692 MPa and very limited plasticity of 0.05%. When Ge increases from 0 to 2 at.%, the strength decreases, but plastic strain increases about 2.5%. Fracture surface and shear bands of samples were investigated by scanning electron microscopy (SEM).

Hormetic effects of noncoplanar PCB exposed to human lung fibroblast cells (HELF) and possible role of oxidative stress.

Science.gov (United States)

Hashmi, Muhammad Zaffar; Khan, Kiran Yasmin; Hu, Jinxing; Naveedullah; Su, Xiaomei; Abbas, Ghulam; Yu, Chunna; Shen, Chaofeng

2015-12-01

Hormesis, a biphasic dose-response phenomenon, which is characterized by stimulation of an end point at a low-dose and inhibition at a high-dose. In the present study we used human lungs fibroblast (HELF) cells as a test model to evaluate the role of oxidative stress (OS) in hormetic effects of non coplanar PCB 101. Results from 3-(4,5-dime-thylthiazol-2-yl)-2,5-diphenyltetrazo-lium bromide (MTT) assay indicated that PCB101 at lower concentrations (10(-5) to 10(-1) μg mL(-1) ) stimulated HELF cell proliferation and inhibited at high concentrations (1, 5, 10, and 20 μg mL(-1) ) in a dose- and time-dependent manner. Reactive oxygen species (ROS), malondialdehyde (MDA) and superoxide dismutase (SOD) (except 48 h) showed a significant increase at higher concentrations of PCB 101 than those at the lower concentrations with the passage of time. Antioxidant enzymes such as glutathione peroxidase (GSH-Px) exhibited decreasing trends in dose and time dependent manner. Lipid peroxidation assay resulted in a significant increase (P PCB 101-treated HELF cells compared with controls, suggesting that OS plays a key role in PCB 101-induced toxicity. Comet assay indicated a significant increase in genotoxicity at higher concentrations of PCB 101 exposure compared to lower concentrations. Overall, we found that HELF cell proliferation was higher at low ROS level and vice versa, which revealed activation of cell signaling-mediated hormetic mechanisms. The results suggested that PCB 101 has hormetic effects to HELF cells and these were associated with oxidative stress. © 2014 Wiley Periodicals, Inc.

Recovering metallic fractions from waste electrical and electronic equipment by a novel vibration system

International Nuclear Information System (INIS)

Habib, Muddasar; Miles, Nicholas J.; Hall, Philip

2013-01-01

Highlights: ► This work focuses on demonstrating a new scaled up technology to separate the metallic and non-metallic fractions of PCBs. ► PCBs comminuted to <1 mm in size resulted in metallic grade concentration of 95% in some of the recovered products. ► Good separation was observed at 40 mm particle bed height due to the formation of well-structured global convection currents. ► The work reported here contributes to the development of a new approach to dry, fine particle separation. - Abstract: The need to recover and recycle valuable resources from Waste Electrical and Electronic Equipment (WEEE) is of growing importance as increasing amounts are generated due to shorter product life cycles, market expansions, new product developments and, higher consumption and production rates. The European Commission (EC) directive, 2002/96/EC, on WEEE became law in UK in January 2007 setting targets to recover up to 80% of all WEEE generated. Printed Wire Board (PWB) and/or Printed Circuit Board (PCB) is an important component of WEEE with an ever increasing tonnage being generated. However, the lack of an accurate estimate for PCB production, future supply and uncertain demands of its recycled materials in international markets has provided the motivation to explore different approaches to recycle PCBs. The work contained in this paper focuses on a novel, dry separation methodology in which vertical vibration is used to separate the metallic and non-metallic fractions of PCBs. When PCBs were comminuted to less than 1 mm in size, metallic grades as high as 95% (measured by heavy liquid analysis) could be achieved in the recovered products

Determination of Lubricant Bulk Modulus in Metal Forming by Means of a Simple Laboratory Test and Inverse FEM Analysis

DEFF Research Database (Denmark)

Hafis, S. M.; Christiansen, P.; Martins, P. A. F.

2016-01-01

The influence of workpiece surface topography on friction, lubrication and final surface equality in metal forming operations is well known and has been pointed out by many researchers.This is especially the case when liquid lubricants are applied in situations, where increased surface roughness ...... couples lubricant flow with plastic deformation of the metal directly. Results show that the proposed procedure allows determining an approximate bulk modulus for the lubricant.......The influence of workpiece surface topography on friction, lubrication and final surface equality in metal forming operations is well known and has been pointed out by many researchers.This is especially the case when liquid lubricants are applied in situations, where increased surface roughness...... facilitates the lubricant entrainment, pressurization and possible escape by micro-plasto-hydrodynamic lubrication. In order to model these mechanisms an important lubricant propertyd esignated as the bulk modulus is needed for characterizing the compressibility of the lubricant. The present paper describes...

Silicon photonic IC embedded optical-PCB for high-speed interconnect application

Science.gov (United States)

Kallega, Rakshitha; Nambiar, Siddharth; Kumar, Abhai; Ranganath, Praveen; Selvaraja, Shankar Kumar

2018-02-01

Optical-Printed Circuit Board (PCB) is an emerging optical interconnect technology to bridge the gap between the board edge and the processing module. The technology so far has been used as a broadband transmitter using polymer waveguides in the PCB. In this paper, we report a Silicon Nitride based photonic IC embedded in the PCB along with the polymers as waveguides in the PCB. The motivation for such integration is to bring routing capability and to reduce the power loss due to broadcasting mode.

Reference standards for quantitative trace analysis of PCB's by GC. Technical PCB formulations for the calibration of ECD and MSD responses

NARCIS (Netherlands)

Krupcik, J.; Kocan, A.; Petrik, J.; Leclercq, P.A.; Ballschmiter, K.

1993-01-01

The compn. of any tech. PCB formulation can be detd. directly by analyzing the PCB sample by gas chromatog. with a flame ionization detector (GC-FID), provided the relative mol. masses of the components are known. The responses of electron capture and selected-ion monitoring, mass-spectra detectors

A high energy microscope for local strain measurements within bulk materials

DEFF Research Database (Denmark)

Lienert, U.; Poulsen, H.F.; Martins, R.V.

2000-01-01

A novel diffraction technique for local, three dimensional strain scanning within bulk materials is presented. The technique utilizes high energy, micro-focussed synchrotron radiation which can penetrate several millimeters into typical metals. The spatial resolution can be as narrow as 1 mum...... in one dimension and in three dimensions about 5x10x100 mum(3) Bulk properties are probed non-destructively and in-situ measurements during thermo-mechanical processing are feasible. A dedicated experimental station has been constructed at the ID11 beamline of the European Synchrotron Radiation Facility...

Transport properties of metal-metal and metal-insulator heterostructures

Energy Technology Data Exchange (ETDEWEB)

Fadlallah Elabd, Mohamed Mostafa

2010-06-09

In this study we present results of electronic structure and transport calculations for metallic and metal-insulator interfaces, based on density functional theory and the non-equilibrium Green's function method. Starting from the electronic structure of bulk Al, Cu, Ag, and Au interfaces, we study the effects of different kinds of interface roughness on the transmission coefficient (T(E)) and the I-V characteristic. In particular, we compare prototypical interface distortions, including vacancies, metallic impurities, non-metallic impurities, interlayer, and interface alloy. We find that vacancy sites have a huge effect on transmission coefficient. The transmission coefficient of non-metallic impurity systems has the same behaviour as the transmission coefficient of vacancy system, since these systems do not contribute to the electronic states at the Fermi energy. We have also studied the transport properties of Au-MgO-Au tunnel junctions. In particular, we have investigated the influence of the thickness of the MgO interlayer, the interface termination, the interface spacing, and O vacancies. Additional interface states appear in the O-terminated configuration due to the formation of Au-O bonds. An increasing interface spacing suppresses the Au-O bonding. Enhancement of T(E) depends on the position and density of the vacancies (the number of vacancies per unit cell). (orig.)

Sexual difference in PCB concentrations of lake trout (Salvelinus namaycush) from Lake Ontario

Science.gov (United States)

Madenjian, Charles P.; Keir, Michael J.; Whittle, D. Michael; Noguchi, George E.

2010-01-01

We determined polychlorinated biphenyl (PCB) concentrations in 61 female lake trout (Salvelinus namaycush) and 71 male lake trout from Lake Ontario (Ontario, Canada and New York, United States). To estimate the expected change in PCB concentration due to spawning, PCB concentrations in gonads and in somatic tissue of lake trout were also determined. In addition, bioenergetics modeling was applied to investigate whether gross growth efficiency (GGE) differed between the sexes. Results showed that, on average, males were 22% higher in PCB concentration than females in Lake Ontario. Results from the PCB determinations of the gonads and somatic tissues revealed that shedding of the gametes led to 3% and 14% increases in PCB concentration for males and females, respectively. Therefore, shedding of the gametes could not explain the higher PCB concentration in male lake trout. According to the bioenergetics modeling results, GGE of males was about 2% higher than adult female GGE, on average. Thus, bioenergetics modeling could not explain the higher PCB concentrations exhibited by the males. Nevertheless, a sexual difference in GGE remained a plausible explanation for the sexual difference in PCB concentrations of the lake trout.

Contribution of nuclear analysis methods to the certification of BCR reference materials for non-metals in non-ferrous metals

International Nuclear Information System (INIS)

Pauwels, J.

1979-01-01

A number of reference materials for oxygen in different non-ferrous metals have been certified by BCR in the frame of a multidisciplinary Community project. The contribution of nuclear analysis methods is illustrated by several examples concerning the optimization of sample preparation techniques, the analysis of low and high oxygen non-ferrous metals and the extension of the program to other non-metals, especially nitrogen and carbon. (author)

Fe-based bulk metallic glasses used for magnetic shielding

Energy Technology Data Exchange (ETDEWEB)

Serban, Va; Codrean, C; UTu, D [Politehnica University of Timisoara, Depart for Materials Science and Welding, 1, M. Viteazu Bvd., 300222, Timisoara (Romania); ErcuTa, A, E-mail: serban@mec.upt.r [West University of Timisoara, Faculty of Physics, 4, Vasile Parvan Bdv., Timisoara 300223 (Romania)

2009-01-01

The casting in complex shapes (tubular) and the main magnetic properties of bulk metallic glasses (BMG) alloys from the ferromagnetic Fe-Cr-Ni-Ga-P-Si-C system, with a small addition of Ni (3%) were studied. Samples as rods and sockets having the thickness up to 1 mm were obtained from master alloys by melt injection by low cooling rates into a Cu mold and annealed in order to ensure adequate magnetic requirements. The structure was examined by X-ray diffraction (XRD) and the basic magnetic properties (coercivity, magnetic remanence, initial susceptibility, etc.) were determined by conventional low frequency induction method. The experimental investigations on producing of BMG ferromagnetic alloys with 3% Ni show the possibility to obtain magnetic shields of complex shape with satisfactory magnetic properties. The presence of Ni does not affect the glass forming ability, but reduce the shielding capacity.

Treatability of PCB-contaminated soils with quicklime (CaO)

International Nuclear Information System (INIS)

Mauro, D.; Taylor, B.B.

1992-12-01

The possibility that quicklime (calcium oxide, CaO) can destroy PCBs has received much attention over the past year. Observations at an EPA remediation site, where lime-containing kiln dusts were used for interim stabilization of PCB-containing wastes prompted the EPA to sponsor a small research project to investigate quicklime-PCB interactions. That study reported decreases in PCB content in synthetic, PCB-spiked soil following the application of quicklime and heat. META Environmental, Inc., as a contractor to EPRI, recently completed research designed to evaluate the effectiveness of quicklime for treating PCBs in soil and sand matrices under several reaction conditions, and to examine the underlying dechlorination chemistry involved, if any. Experiments were run with PCB-spiked sand and with actual PCB-contaminated soil. A variety of experimental conditions were employed including tests in open and closed containers, at ambient and elevated temperatures, and over a range of one hour to four days. Granular quicklime, fly ash, and kiln dust were all tested for reaction with PCBs. Early experiments showed that a mixture of sand/quicklime/water at 1:3:1.5 by weight, placed in an insulated container reached a maximum temperature of 216 degree C. Treatability experiments were subsequently run under controlled heat at room temperature, at 80 degree C, and at 200 degree C (following the initial temperature increase which occurs when water is added to quicklime). Little or no loss of PCBs was observed in open or closed containers at ambient or at 800 degree C over any period of time studied. A significant decrease of PCBs levels was observed only in the high temperature experiments (above 200 degree C), however the fate of the PCBs in those experiments was not determined. The conditions and the results of the PCB treatment tests are presented in this report, as well as recommendations for further studies

Acute alteration of cardiac ECG, action potential, I{sub Kr} and the human ether-a-go-go-related gene (hERG) K{sup +} channel by PCB 126 and PCB 77

Energy Technology Data Exchange (ETDEWEB)

Park, Mi-Hyeong; Park, Won Sun; Jo, Su-Hyun, E-mail: suhyunjo@kangwon.ac.kr

2012-07-01

Polychlorinated biphenyls (PCBs) have been known as serious persistent organic pollutants (POPs), causing developmental delays and motor dysfunction. We have investigated the effects of two PCB congeners, 3,3′,4,4′-tetrachlorobiphenyl (PCB 77) and 3,3′,4,4′,5-pentachlorobiphenyl (PCB 126) on ECG, action potential, and the rapidly activating delayed rectifier K{sup +} current (I{sub Kr}) of guinea pigs' hearts, and hERG K{sup +} current expressed in Xenopus oocytes. PCB 126 shortened the corrected QT interval (QTc) of ECG and decreased the action potential duration at 90% (APD{sub 90}), and 50% of repolarization (APD{sub 50}) (P < 0.05) without changing the action potential duration at 20% (APD{sub 20}). PCB 77 decreased APD{sub 20} (P < 0.05) without affecting QTc, APD{sub 90}, and APD{sub 50}. The PCB 126 increased the I{sub Kr} in guinea-pig ventricular myocytes held at 36 °C and hERG K{sup +} current amplitude at the end of the voltage steps in voltage-dependent mode (P < 0.05); however, PCB 77 did not change the hERG K{sup +} current amplitude. The PCB 77 increased the diastolic Ca{sup 2+} and decreased Ca{sup 2+} transient amplitude (P < 0.05), however PCB 126 did not change. The results suggest that PCB 126 shortened the QTc and decreased the APD{sub 90} possibly by increasing I{sub Kr}, while PCB 77 decreased the APD{sub 20} possibly by other modulation related with intracellular Ca{sup 2+}. The present data indicate that the environmental toxicants, PCBs, can acutely affect cardiac electrophysiology including ECG, action potential, intracellular Ca{sup 2+}, and channel activity, resulting in toxic effects on the cardiac function in view of the possible accumulation of the PCBs in human body. -- Highlights: ► PCBs are known as serious environmental pollutants and developmental disruptors. ► PCB 126 shortened QT interval of ECG and action potential duration. ► PCB 126 increased human ether-a-go-go-related K{sup +} current and I{sub Kr}. �

PCB exposure and cochlear function at age 6 years.

Science.gov (United States)

Palkovičová Murínová, Ľubica; Moleti, Arturo; Sisto, Renata; Wimmerová, Soňa; Jusko, Todd A; Tihányi, Juraj; Jurečková, Dana; Kováč, Ján; Koštiaková, Vladimíra; Drobná, Beata; Trnovec, Tomáš

2016-11-01

Epidemiological studies have documented adverse associations between exposure to polychlorinated biphenyls (PCBs) and otological outcomes. Previously, we documented decreased distortion product otoacoustic emission (DPOAE) levels in children exposed to PCBs, up to the age of 45 months, amongst a cohort of children in eastern Slovakia. The objective of the present study is to evaluate cochlear dysfunction at 72 months of age in 214 children from this same cohort and to compare the otoacoustic test sensitivity to that of pure tone audiometry (PTA). The association between DPOAE, PTA, and PCBs was estimated by means of multivariate ANOVA (MANOVA) and linear regression models. ROC curves were computed to estimate the DPOAE-test power in children. The DPOAE level at 72 months was related to PCB-153 serum levels. The DPOAE Input/Output function test at mid-frequency (2kHz) has shown instead nonmonotonic dependence on PCB exposure, for the left ears of children, over the whole growth curve. No significant association was found between PTA hearing levels and PCB-153 concentration. High diagnostic power of the DPOAE-test was found in children, similar to that found by the same authors in adults. In conclusions the DPOAE-PCB correlation obtained at 72 months is similar to that at 45 months suggesting a permanent and stable ototoxic effect of the PCB exposure. The lack of statistical significance of the PCB-PTA correlation suggests that DPOAEs are sensitive biomarkers of cochlear damage. Copyright © 2016 Elsevier Inc. All rights reserved.

Role of electrode metallization in the performance of bulk semi-insulating InP radiation detectors

International Nuclear Information System (INIS)

Zatko, B.; Dubecky, F.; Prochazkova, O.; Necas, V.

2007-01-01

This work deals with the study of three different electrode metallizations with the aim to form a Schottky barrier contact. Electrode geometry corresponds to the requirements of digital radiography systems. As substrates bulk Liquid Encapsulated Czochralski (LEC) SI InP wafers doped with Fe and Fe+Zn are used. Results of this study show that no one of the used metallization performs as a blocking contact. However, detectors with Ti/Pt/Au metallization attained a relatively good energy resolution of 7.0 keV in full-width at half-maximum (FWHM) and the charge collection efficiency (CCE) higher than 83% for 122 keV γ-photons at 255 K. The development of SI InP radiation detectors and in particular their electrode technology is discussed in the light of observed results

Chamber study of PCB emissions from caulking materials and light ballasts.

Science.gov (United States)

Liu, Xiaoyu; Guo, Zhishi; Krebs, Kenneth A; Stinson, Rayford A; Nardin, Joshua A; Pope, Robert H; Roache, Nancy F

2015-10-01

The emissions of polychlorinated biphenyl (PCB) congeners from thirteen caulk samples were tested in a micro-chamber system. Twelve samples were from PCB-contaminated buildings and one was prepared in the laboratory. Nineteen light ballasts collected from buildings that represent 13 different models from five manufacturers were tested in 53-L environmental chambers. The rates of PCB congener emissions from caulking materials and light ballasts were determined. Several factors that may have affected the emission rates were evaluated. The experimentally determined emission factors showed that, for a given PCB congener, there is a linear correlation between the emission factor and the concentration of the PCB congener in the source. Furthermore, the test results showed that an excellent log-linear correlation exists between the normalized emission factor and the vapor pressure (coefficient of determination, r(2)⩾0.8846). The PCB congener emissions from ballasts at or near room temperature were relatively low with or without electrical load. However, the PCB congener emission rates increased significantly as the temperature increased. The results of this research provide new data and models for ranking the primary sources of PCBs and supports the development and refinement of exposure assessment models for PCBs. Published by Elsevier Ltd.

Metals in bulk deposition and surface waters at two upland locations in northern England

Energy Technology Data Exchange (ETDEWEB)

Lawlor, A.J.; Tipping, E

2003-02-01

Surface water concentrations of potentially-toxic metals depend upon atmospheric deposition and catchment biogeochemical processes. - Concentrations of aluminium and minor metals (Mn, Ni, Cu, Zn, Sr, Cd, Ba, Pb) were measured in precipitation and surface water at two upland locations (Upper Duddon Valley, UDV; Great Dun Fell, GDF) in northern England for 1 year commencing April 1998. At both locations, the loads in bulk precipitation were at the lower ends of ranges reported for other rural and remote sites, for the period 1985-1995. The deposited metals were mostly in the dissolved form, and their concentrations tended to be greatest when rainfall volumes were low. The concentrations of Cu, Zn and Pb in deposition were correlated (r{sup 2}{>=}0.40) with concentrations of non-marine sulphate. Three streams, ranging in mean pH from 5.07 to 7.07, and with mean concentrations of dissolved organic carbon (DOC) <1 mg l{sup -1}, were monitored at UDV, and two pools (mean pH 4.89 and 6.83, mean DOC 22 and 15 mg l{sup -1}) at GDF. Aluminium and the minor metals were mainly in the dissolved form, and in the following ranges (means of 49-51 samples, {mu}g l{sup -1}): Al 36-530, Mn 4.4-36, Ni 0.26-2.8, Cu 0.25-1.7, Zn 2.1-30, Cd 0.03-0.16, Ba 1.9-140, Pb 0.10-4.5. Concentrations were generally higher at GDF. Differences in metal concentrations between the two locations and between waters at each location, and temporal variations in individual waters, can be explained qualitatively in terms of sorption to solid-phase soil organic matter and mineral surfaces, complexation and transport by DOC, and chemical weathering. The UDV catchments are sinks for Pb and sources of Al, Mn, Sr, Cd and Ba. The GDF catchments are sources of Al, Mn, Ni, Zn, Sr, Cd and Ba. Other metals measured at the two locations are approximately in balance. Comparison of metal:silicon ratios in the surface waters with values for silicate rocks indicates enrichment of Ni and Cu, and substantial enrichment of

PCB dechlorination hotspots and reductive dehalogenase genes in sediments from a contaminated wastewater lagoon.

Science.gov (United States)

Mattes, Timothy E; Ewald, Jessica M; Liang, Yi; Martinez, Andres; Awad, Andrew; Richards, Patrick; Hornbuckle, Keri C; Schnoor, Jerald L

2017-08-12

Polychlorinated biphenyls (PCBs) are a class of persistent organic pollutants that are distributed worldwide. Although industrial PCB production has stopped, legacy contamination can be traced to several different commercial mixtures (e.g., Aroclors in the USA). Despite their persistence, PCBs are subject to naturally occurring biodegradation processes, although the microbes and enzymes involved are poorly understood. The biodegradation potential of PCB-contaminated sediments in a wastewater lagoon located in Virginia (USA) was studied. Total PCB concentrations in sediments ranged from 6.34 to 12,700 mg/kg. PCB congener profiles in sediment sample were similar to Aroclor 1248; however, PCB congener profiles at several locations showed evidence of dechlorination. The sediment microbial community structure varied among samples but was dominated by Proteobacteria and Firmicutes. The relative abundance of putative dechlorinating Chloroflexi (including Dehalococcoides sp.) was 0.01-0.19% among the sediment samples, with Dehalococcoides sp. representing 0.6-14.8% of this group. Other possible PCB dechlorinators present included the Clostridia and the Geobacteraceae. A PCR survey for potential PCB reductive dehalogenase genes (RDases) yielded 11 sequences related to RDase genes in PCB-respiring Dehalococcoides mccartyi strain CG5 and PCB-dechlorinating D. mccartyi strain CBDB1. This is the first study to retrieve potential PCB RDase genes from unenriched PCB-contaminated sediments.

Homogeneous viscous flow behavior of a Cu–Zr based bulk metallic glass composites

International Nuclear Information System (INIS)

Zhang, X.Y.; Yuan, Z.Z.; Feng, X.L.; Cui, L.Z.; Li, D.X.

2015-01-01

In this paper, Cu 40 Zr 44 Ag 8 Al 8 bulk metallic glass composites (BMGCs) consisting of various volume fraction of nanocrystals embedded in the amorphous matrix was synthesized by controlled annealing treatment of an as-cast BMGCs. The high temperature compression behaviors of the BMGCs were characterized in the supercooled liquid region. Results show that the flow stresses keep increasing after an initial decrease with extension of the annealing time. With annealing the values of activation volume V act is determined to be increasing from 283.6216 Ǻ 3 to 305.553 Ǻ 3 , suggesting that the jump of atoms is a cooperative process during the high-temperature deformation. Flow behavior of the BMGCs annealed for less than 8 min transform from Newtonian to non-Newtonian dependant on the stain rate and can be successively fitted by the visco-plasticity model. Fitting results indicate that deformation behaviors of these samples are governed by homogeneous flow of the amorphous matrix and indeed determined by the viscosities in the Newtonian flow stage. However, the BMGCs annealed for 8 min exhibit a non-Newtonian flow over the entire compression process and fail to be fitted by the visco-plasticity model. Micrographs of the sample reflect an impinged structure, indicating that high temperature deformation behavior of the BMGCs with high volume fractions of particles is indeed controlled by that of a backbone of particles

Impact of the structural state on the mechanical properties in a Zr–Co–Al bulk metallic glass

International Nuclear Information System (INIS)

Qiao, J.C.; Pelletier, J.M.; Esnouf, C.; Liu, Y.; Kato, H.

2014-01-01

Highlights: • Atomic mobility in metallic glass was studied by DMA, HRTEM and nanoindentation. • Physical ageing and crystallization reduce the atomic mobility. • Plastic deformation, i.e. cold-rolling enhances the atomic mobility. • Atomic mobility in glassy materials can be described by quasi-point defects model. - Abstract: This paper reports on the use of differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA) and nanoindentation technique to investigate atomic mobility in Zr 56 Co 28 Al 16 bulk metallic glass in the as-cast state, after thermal annealing and after cold rolling. From the DMA results together with nanoindentation data point of view, the atomic mobility is significantly modified by the thermo-mechanical history. On the one hand, atomic mobility in bulk metallic glass is reduced after physical aging or crystallization. On the other hand, the atomic mobility in metallic glass is enhanced by cold rolling. To analyze the atomic mobility in amorphous materials, a physical theory is introduced. This model invoked the concept of quasi-point defects, which correspond to the density fluctuations in the glassy materials. Correlated movements of atoms are assisted by these quasi-point defects and the correlation factor χ is connected to the concentration of these “defects” in metallic glasses: (i) physical aging and crystallization decreases the parameter χ and (ii) the concentration of defects augments via plastic deformation (i.e. cold-rolling), suggesting that the correlation factor χ reflects the atomic mobility for glassy materials in a quantitative manner. This correlation bridges the gap between the mechanical properties on macroscopic scale and atomic mobility in microstructural regions in metallic glasses

Microbial community analysis of switchgrass planted and unplanted soil microcosms displaying PCB dechlorination.

Science.gov (United States)

Liang, Yi; Meggo, Richard; Hu, Dingfei; Schnoor, Jerald L; Mattes, Timothy E

2015-08-01

Polychlorinated biphenyls (PCBs) pose potential risks to human and environmental health because they are carcinogenic, persistent, and bioaccumulative. In this study, we investigated bacterial communities in soil microcosms spiked with PCB 52, 77, and 153. Switchgrass (Panicum virgatum) was employed to improve overall PCB removal, and redox cycling (i.e., sequential periods of flooding followed by periods of no flooding) was performed in an effort to promote PCB dechlorination. Lesser chlorinated PCB transformation products were detected in all microcosms, indicating the occurrence of PCB dechlorination. Terminal restriction fragment length polymorphism (T-RFLP) and clone library analysis showed that PCB spiking, switchgrass planting, and redox cycling affected the microbial community structure. Putative organohalide-respiring Chloroflexi populations, which were not found in unflooded microcosms, were enriched after 2 weeks of flooding in the redox-cycled microcosms. Sequences classified as Geobacter sp. were detected in all microcosms and were most abundant in the switchgrass-planted microcosm spiked with PCB congeners. The presence of possible organohalide-respiring bacteria in these soil microcosms suggests that they play a role in PCB dechlorination therein.

Micromechanical modeling of tungsten-based bulk metallic glass matrix composites

Energy Technology Data Exchange (ETDEWEB)

Li Hao [Department of Mechanical Engineering-Engineering Mechanics, Michigan Technological University, 1400 Townsend Drive, Houghton, MI 49931 (United States); Li Ke [Department of Mechanical Engineering, Texas A and M University, TAMU 3123, College Station, TX 77843 (United States)]. E-mail: keli@tamu.edu; Subhash, Ghatu [Department of Mechanical Engineering-Engineering Mechanics, Michigan Technological University, 1400 Townsend Drive, Houghton, MI 49931 (United States); Kecskes, Laszlo J. [Weapons and Materials Research Directorate, US Army Research Laboratory, Aberdeen Proving Ground, MD 21005 (United States); Dowding, Robert J. [Weapons and Materials Research Directorate, US Army Research Laboratory, Aberdeen Proving Ground, MD 21005 (United States)

2006-08-15

Micromechanics models are developed for tungsten (W)-based bulk metallic glass (BMG) matrix composites employing the Voronoi tessellation technique and the finite element (FE) method. The simulation results indicate that the computed elastic moduli are close to those measured in the experiments. The predicted stress-strain curves agree well with their experimentally obtained counterparts in the early stage of the plastic deformation. An increase in the W volume fraction leads to a decrease in the yield stress and an increase in the Young's modulus of the composite. In addition, contours of equivalent plastic strain for increasing applied strains provide an explanation why shear bands were observed in the glassy phase, along the W/BMG interface, and in the W phase of failed W/BMG composite specimens.

Atmospherically deposited trace metals from bulk mineral concentrate port operations.

Science.gov (United States)

Taylor, Mark Patrick

2015-05-15

Although metal exposures in the environment have declined over the last two decades, certain activities and locations still present a risk of harm to human health. This study examines environmental dust metal and metalloid hazards (arsenic, cadmium, lead and nickel) associated with bulk mineral transport, loading and unloading port operations in public locations and children's playgrounds in the inner city of Townsville, northern Queensland. The mean increase in lead on post-play hand wipes (965 μg/m(2)/day) across all sites was more than 10-times the mean pre-play loadings (95 μg/m(2)/day). Maximum loading values after a 10-minute play period were 3012 μg/m(2), more than seven times the goal of 400 μg/m(2) used by the Government of Western Australia (2011). Maximum daily nickel post-play hand loadings (404 μg/m(2)) were more than 26 times above the German Federal Immission Control Act 2002 annual benchmark of 15 μg/m(2)/day. Repeat sampling over the 5-day study period showed that hands and surfaces were re-contaminated daily from the deposition of metal-rich atmospheric dusts. Lead isotopic composition analysis of dust wipes ((208)Pb/(207)Pb and (206)Pb/(207)Pb) showed that surface dust lead was similar to Mount Isa type ores, which are exported through the Port of Townsville. While dust metal contaminant loadings are lower than other mining and smelting towns in Australia, they exceeded national and international benchmarks for environmental quality. The lessons from this study are clear - even where operations are considered acceptable by managing authorities, targeted assessment and monitoring can be used to evaluate whether current management practices are truly best practice. Reassessment can identify opportunities for improvement and maximum environmental and human health protection. Copyright © 2015 Elsevier B.V. All rights reserved.

γIrradiation induced formation of PCB-solvent adducts in aliphatic solvents

International Nuclear Information System (INIS)

Lepine, F.; Milot, S.; Gagne, N.

1990-01-01

γIrradiation induced formation of PCB-solvent adducts was investigated as a model for PCB residues in irradiated food. Formation of cyclohexyl adducts of PCBs was found to be significant when pure PCB congeners and Aroclor mixture were irradiated in cyclohexane and cyclohexene. Reaction pathways were investigated, and the effects of oxygen and electron scavenger were studied

Molecular Dynamics Simulations of Grain Boundary and Bulk Diffusion in Metals.

Science.gov (United States)

Plimpton, Steven James

Diffusion is a microscopic mass transport mechanism that underlies many important macroscopic phenomena affecting the structural, electrical, and mechanical properties of metals. This thesis presents results from atomistic simulation studies of diffusion both in bulk and in the fast diffusion paths known as grain boundaries. Using the principles of molecular dynamics single boundaries are studied and their structure and dynamic properties characterized. In particular, tilt boundary bicrystal and bulk models of fcc Al and bcc alpha-Fe are simulated. Diffusion coefficients and activation energies for atomic motion are calculated for both models and compared to experimental data. The influence of the interatomic pair potential on the diffusion is studied in detail. A universal relation between the melting temperature that a pair potential induces in a simulated bulk model and the potential energy barrier height for atomic hopping is derived and used to correlate results for a wide variety of pair potentials. Using these techniques grain boundary and bulk diffusion coefficients for any fcc material can be estimated from simple static calculations without the need to perform more time-consuming dynamic simulations. The influences of two other factors on grain boundary diffusion are also studied because of the interest of the microelectronics industry in the diffusion related reliability problem known as electromigration. The first factor, known to affect the self diffusion rate of Al, is the presence of Cu impurity atoms in Al tilt boundaries. The bicrystal model for Al is seeded randomly with Cu atoms and a simple hybrid Morse potential used to model the Al-Cu interaction. While some effect due to the Cu is noted, it is concluded that pair potentials are likely an inadequate approximation for the alloy system. The second factor studied is the effect of the boundary orientation angle on the diffusion rate. Symmetric bcc Fe boundaries are relaxed to find optimal

Efficiency Enhancement in Bulk Heterojunction Polymer Photovoltaic Cells Using ZrTiO4/Bi2O3 Metal-Oxide Nanocomposites

DEFF Research Database (Denmark)

Abdul Jabbar, Mohammed Hussain; Neppolian, B.; Shim, Hee-Sang

2010-01-01

We report the effect of metal-oxide nanocomposites on the performance of bulk heterojunction polymer solar cells. A photoactive layer composed of poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) was blended with a newly developed ZrTiO4/Bi2O3 (BITZ) metal-oxide...

Atomic structure and formation of CuZrAl bulk metallic glasses and composites

International Nuclear Information System (INIS)

Kaban, I.; Jóvári, P.; Escher, B.; Tran, D.T.; Svensson, G.; Webb, M.A.; Regier, T.Z.; Kokotin, V.; Beuneu, B.; Gemming, T.; Eckert, J.

2015-01-01

Graphical abstract: Partial radial distribution functions for Cu 47.5 Zr 47.5 Al 5 metallic glass and relevant crystal structures. - Abstract: Cu 47.5 Zr 47.5 Al 5 metallic glass is studied experimentally by high-energy X-ray diffraction, neutron diffraction with isotopic substitution, electron diffraction and X-ray absorption spectroscopy. The atomic structure of the glass is modeled by reverse Monte-Carlo and molecular dynamics simulations. RMC modeling of seven experimental datasets enabled reliable separation of all partial pair distribution functions for Cu 47.5 Zr 47.5 Al 5 metallic glass. A peculiar structural feature of the ternary alloy is formation of the strong Al–Zr bonds, which are supposed to determine its high viscosity and enhanced bulk glass formation. Analysis of the local atomic order in Cu 47.5 Zr 47.5 Al 5 glass and Cu 10 Zr 7 , CuZr 2 and CuZr B2 crystalline structures elucidates their similarities and differences explaining the phase formation sequence by devitrification of the glass.

Formation and Applications of Bulk Glassy Alloys in Late Transition Metal Base System

International Nuclear Information System (INIS)

Inoue, Akihisa; Shen Baolong

2006-01-01

This paper reviews our recent results of the formation, fundamental properties, workability and applications of late transition metal (LTM) base bulk glassy alloys (BGAs) developed since 1995. The BGAs were obtained in Fe-(Al,Ga)-(P,C,B,Si), Fe-(Cr,Mo)-(C,B), Fe-(Zr,Hf,Nb,Ta)-B, Fe-Ln-B(Ln=lanthanide metal), Fe-B-Si-Nb and Fe-Nd-Al for Fe-based alloys, Co-(Ta,Mo)-B and Co-B-Si-Nb for Co-based alloys, Ni-Nb-(Ti,Zr)-(Co,Ni) for Ni-based alloys, and Cu-Ti-(Zr,Hf), Cu-Al-(Zr,Hf), Cu-Ti-(Zr,Hf)-(Ni,Co) and Cu-Al-(Zr,Hf)-(Ag,Pd) for Cu-based alloys. These BGAs exhibit useful properties of high mechanical strength, large elastic elongation and high corrosion resistance. In addition, Fe- and Co-based glassy alloys have good soft magnetic properties which cannot be obtained for amorphous and crystalline type magnetic alloys. The Fe- and Ni-based BGAs have already been used in some application fields. These LTM base BGAs are promising as new metallic engineering materials

Estimating dermal transfer from PCB-contaminated porous surfaces.

Science.gov (United States)

Slayton, T M; Valberg, P A; Wait, A D

1998-06-01

Health risks posed by dermal contact with PCB-contaminated porous surfaces have not been directly demonstrated and are difficult to estimate indirectly. Surface contamination by organic compounds is commonly assessed by collecting wipe samples with hexane as the solvent. However, for porous surfaces, hexane wipe characterization is of limited direct use when estimating potential human exposure. Particularly for porous surfaces, the relationship between the amount of organic material collected by hexane and the amount actually picked up by, for example, a person's hand touch is unknown. To better mimic PCB pickup by casual hand contact with contaminated concrete surfaces, we used alternate solvents and wipe application methods that more closely mimic casual dermal contact. Our sampling results were compared to PCB pickup using hexane-wetted wipes and the standard rubbing protocol. Dry and oil-wetted samples, applied without rubbing, picked up less than 1% of the PCBs picked up by the standard hexane procedure; with rubbing, they picked up about 2%. Without rubbing, saline-wetted wipes picked up 2.5%; with rubbing, they picked up about 12%. While the nature of dermal contact with a contaminated surface cannot be perfectly reproduced with a wipe sample, our results with alternate wiping solvents and rubbing methods more closely mimic hand contact than the standard hexane wipe protocol. The relative pickup estimates presented in this paper can be used in conjunction with site-specific PCB hexane wipe results to estimate dermal pickup rates at sites with PCB-contaminated concrete.

Metal nanostructures for non-enzymatic glucose sensing

International Nuclear Information System (INIS)

Tee, Si Yin; Teng, Choon Peng; Ye, Enyi

2017-01-01

This review covers the recent development of metal nanostructures in electrochemical non-enzymatic glucose sensing. It highlights a variety of nanostructured materials including noble metals, other transition metals, bimetallic systems, and their hybrid with carbon-based nanomaterials. Particularly, attention is devoted to numerous approaches that have been implemented for improving the sensors performance by tailoring size, shape, composition, effective surface area, adsorption capability and electron-transfer properties. The correlation of the metal nanostructures to the glucose sensing performance is addressed with respect to the linear concentration range, sensitivity and detection limit. In overall, this review provides important clues from the recent scientific achievements of glucose sensor nanomaterials which will be essentially useful in designing better and more effective electrocatalysts for future electrochemical sensing industry. - Highlights: • Overview of recent development of metal nanostructures in electrochemical non-enzymatic glucose sensing. • Special attention is focussed on noble metals, other transition metals, bimetallic systems, and their hybrid with carbon-based nanomaterials. • Merits and limitations of various metal nanostructures in electrochemical non-enzymatic glucose sensing. • Strategies to improve the glucose sensing performance of metal nanostructures as electrocatalysts.

Formation of Ti--Zr--Cu--Ni bulk metallic glasses

International Nuclear Information System (INIS)

Lin, X.H.; Johnson, W.L.

1995-01-01

Formation of bulk metallic glass in quaternary Ti--Zr--Cu--Ni alloys by relatively slow cooling from the melt is reported. Thick strips of metallic glass were obtained by the method of metal mold casting. The glass forming ability of the quaternary alloys exceeds that of binary or ternary alloys containing the same elements due to the complexity of the system. The best glass forming alloys such as Ti 34 Zr 11 Cu 47 Ni 8 can be cast to at least 4-mm-thick amorphous strips. The critical cooling rate for glass formation is of the order of 250 K/s or less, at least two orders of magnitude lower than that of the best ternary alloys. The glass transition, crystallization, and melting behavior of the alloys were studied by differential scanning calorimetry. The amorphous alloys exhibit a significant undercooled liquid region between the glass transition and first crystallization event. The glass forming ability of these alloys, as determined by the critical cooling rate, exceeds what is expected based on the reduced glass transition temperature. It is also found that the glass forming ability for alloys of similar reduced glass transition temperature can differ by two orders of magnitude as defined by critical cooling rates. The origins of the difference in glass forming ability of the alloys are discussed. It is found that when large composition redistribution accompanies crystallization, glass formation is enhanced. The excellent glass forming ability of alloys such as Ti 34 Zr 11 Cu 47 Ni 8 is a result of simultaneously minimizing the nucleation rate of the competing crystalline phases. The ternary/quaternary Laves phase (MgZn 2 type) shows the greatest ease of nucleation and plays a key role in determining the optimum compositions for glass formation. copyright 1995 American Institute of Physics

A modeling approach to compare ΣPCB concentrations between congener-specific analyses

Science.gov (United States)

Gibson, Polly P.; Mills, Marc A.; Kraus, Johanna M.; Walters, David M.

2017-01-01

Changes in analytical methods over time pose problems for assessing long-term trends in environmental contamination by polychlorinated biphenyls (PCBs). Congener-specific analyses vary widely in the number and identity of the 209 distinct PCB chemical configurations (congeners) that are quantified, leading to inconsistencies among summed PCB concentrations (ΣPCB) reported by different studies. Here we present a modeling approach using linear regression to compare ΣPCB concentrations derived from different congener-specific analyses measuring different co-eluting groups. The approach can be used to develop a specific conversion model between any two sets of congener-specific analytical data from similar samples (similar matrix and geographic origin). We demonstrate the method by developing a conversion model for an example data set that includes data from two different analytical methods, a low resolution method quantifying 119 congeners and a high resolution method quantifying all 209 congeners. We used the model to show that the 119-congener set captured most (93%) of the total PCB concentration (i.e., Σ209PCB) in sediment and biological samples. ΣPCB concentrations estimated using the model closely matched measured values (mean relative percent difference = 9.6). General applications of the modeling approach include (a) generating comparable ΣPCB concentrations for samples that were analyzed for different congener sets; and (b) estimating the proportional contribution of different congener sets to ΣPCB. This approach may be especially valuable for enabling comparison of long-term remediation monitoring results even as analytical methods change over time. 

Evaluation of the toxicity of sediments from the Anniston PCB Site to the mussel Lampsilis siliquoidea

Science.gov (United States)

Schein, Allison; Sinclair, Jesse A.; MacDonald, Donald D.; Ingersoll, Christopher G.; Kemble, Nile E.; Kunz, James L.

2015-01-01

The Anniston Polychlorinated Biphenyl (PCB) Site is located in the vicinity of the municipality of Anniston in Calhoun County, in the north-eastern portion of Alabama. Although there are a variety of land-use activities within the Choccolocco Creek watershed, environmental concerns in the area have focused mainly on releases of PCBs to aquatic and riparian habitats. PCBs were manufactured by Monsanto, Inc. at the Anniston facility from 1935 to 1971. The chemicals of potential concern (COPCs) in sediments at the Anniston PCB Site include: PCBs, mercury, metals, polycyclic aromatic hydrocarbons (PAHs), organochlorine and organophosphorous pesticides, volatile organic compounds (VOCs), semivolatile organic compounds (SVOCs), and polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDDs/PCDFs). The purpose of this study was to evaluate the toxicity of PCB-contaminated sediments to the juvenile fatmucket mussel (Lampsilis siliquoidea) and to characterize relationships between sediment chemistry and the toxicity of sediment samples collected from the Anniston PCB Site using laboratory sediment testing. Samples were collected in August 2010 from OU-4 of the Anniston PCB Site, as well as from selected reference locations. A total of 32 samples were initially collected from six test sites and one reference site within the watershed. A total of 23 of these 32 samples were evaluated in 28-day whole-sediment toxicity tests conducted with juvenile mussels (L. siliquoidea). Physical and chemical characterization of whole sediment included grain size, total organic carbon (TOC), nutrients, PCBs, parent and alkylated PAHs, organochlorine pesticides, PCDD/PCDFs, total metals, simultaneously extracted metals (SEM), and acid volatile sulfide (AVS). Sediment collected from Snow Creek and Choccolocco Creek contained a variety of COPCs. Organic contaminants detected in sediment included PCBs, organochlorine pesticides, PCDDs/PCDFs, and PAHs. In general, the highest

Estrogenicity and androgenicity screening of PCB sulfate monoesters in human breast cancer MCF-7 cells

OpenAIRE

Flor, Susanne; He, Xianran; Lehmler, Hans-Joachim; Ludewig, Gabriele

2015-01-01

Recent studies identified PCB sulfate esters as a major product of PCB metabolism. Since hydroxy-PCBs (HO-PCBs), the immediate precursors of PCB sulfates and important contributors to PCB toxicity, were shown to have estrogenic activity, we investigated the estrogenicity/androgenicty of a series of PCB sulfate metabolites. We synthesized the five possible structural sulfate monoester metabolites of PCB 3, a congener shown to be biotransformed to sulfates, a sulfate ester of the paint-specific...

Low consumption single-use microvalve for microfluidic PCB-based platforms

International Nuclear Information System (INIS)

Flores, G; Aracil, C; Perdigones, F; Quero, J M

2014-01-01

In this paper, a single-use and unidirectional microvalve with low consumption of energy for PCB-based microfluidic platforms is reported. Its activation is easy because it works as a fuse. The fabrication process of the device is based on PCB technology and a typical SU-8 process, using the PCB as a substrate and SU-8 for the microfluidic channels and chambers. The microvalve is intended to be used to impulse small volumes of fluids and it has been designed to be highly integrable in PCB-based microfluidic platforms. The proposed device has been fabricated, integrated and tested in a general purpose microfluidic circuit, resulting in a low activation time, of about 100 μs, and a low consumption of energy, with a maximum of 27 mJ. These results show a significant improvement because the energy consumption is about 84% lower and the time response is about four orders of magnitude shorter if compared with similar microvalves for impulsion of fluids on PCB-based platforms. (paper)

Studies on the distribution of 14C-labelled PCB in the body, 4

International Nuclear Information System (INIS)

Nagao, Soshichi; Hosoya, Hideo

1976-01-01

This paper is a report of 14 C-PCB distribution series in animals. We reported the results of the distribution of 14 C-PCB from birds, fish and shell in the previous experiments, and we have obtained some results from present experiment. This time interperito neal injection of 14 C-PCB solution was carried to mice, and the results were as follows; Excretion of 14 C-PCB as radioactivity was at its maximum about 6 hr. after medication. Excretive ratio was 87.20% for 24 hr, but 72.43% of radioactivity was excreted within 12hr. The result of radiopaperchromatography showed that 14 C-PCB was not changeable in the fecus after medication, being Rf = 0.92 in comparison with standard 14 C-PCB. 14 C-PCB distributed throughout the body of mice in 24 hr. and at least remained over till 480 hr. in adipose tissues of mice after single medication. (auth.)

Sexual difference in PCB concentrations of walleyes (Sander vitreus) from a pristine lake

Science.gov (United States)

Madenjian, C.P.; Hanchin, P.A.; Chernyak, S.M.; Begnoche, L.J.

2009-01-01

We determined polychlorinated biphenyl (PCB) concentrations in 15 adult female walleyes (Sander vitreus) and 15 adult male walleyes from South Manistique Lake (Michigan, United States), a relatively pristine lake with no point source inputs of PCBs. By measuring PCB concentration in gonads and in somatic tissue of the South Manistique Lake fish, we also estimated the expected change in PCB concentration due to spawning for both sexes. To determine whether gross growth efficiency differed between the sexes, we applied bioenergetics modeling. Results showed that, on average, adult males were 34% higher in PCB concentration than adult females in South Manistique Lake. Results from the PCB determinations of the gonads and somatic tissues revealed that shedding of the gametes led to 1% and 5% increases in PCB concentration for males and females, respectively. Therefore, shedding of the gametes could not explain the higher PCB concentration in adult male walleyes. Bioenergetics modeling results indicated that the sexual difference in PCB concentrations of South Manistique Lake walleyes was attributable, at least in part, to a sexual difference in gross growth efficiency (GGE). Adult female GGE was estimated to be up to 17% greater than adult male GGE.

77 FR 13603 - Anniston PCB Superfund Site; Anniston, Calhoun County, AL; Correction

Science.gov (United States)

2012-03-07

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9644-2; CERCLA-04-2012-3763] Anniston PCB Superfund Site... FR 11533 (FRL-9637-7), EPA posted a Notice of Amended Settlement concerning the Anniston PCB... the settlement are available from Ms. Paula V. Painter. Submit your comments by Site name Anniston PCB...

Regulation of pregnane-X-receptor, CYP3A and P-glycoprotein genes in the PCB-resistant killifish (Fundulus heteroclitus) population from New Bedford Harbor

International Nuclear Information System (INIS)

Gräns, Johanna; Wassmur, Britt; Fernández-Santoscoy, María; Zanette, Juliano; Woodin, Bruce R.; Karchner, Sibel I.; Nacci, Diane E.; Champlin, Denise; Jayaraman, Saro; Hahn, Mark E.; Stegeman, John J.; Celander, Malin C.

2015-01-01

Highlights: • Basal levels of PXR and Pgp mRNA are lower in liver of fish from NBH than from SC. • Hepatic PXR, CYP3A and Pgp mRNA levels are induced by PCB in fish from NBH. • Both non-dioxin-like and dioxin-like PCBs induce PXR, CYP3A and Pgp in NBH fish. • Branchial PXR and CYP3A mRNA levels are induced by PCB 126 in fish from SC. • There is possible cross-talk between AhR and PXR signaling in killifish. - Abstract: Killifish survive and reproduce in the New Bedford Harbor (NBH) in Massachusetts (MA), USA, a site severely contaminated with polychlorinated biphenyls (PCBs) for decades. Levels of 22 different PCB congeners were analyzed in liver from killifish collected in 2008. Concentrations of dioxin-like PCBs in liver of NBH killifish were ∼400 times higher, and the levels of non-dioxin-like PCBs ∼3000 times higher than in killifish from a reference site, Scorton Creek (SC), MA. The NBH killifish are known to be resistant to the toxicity of dioxin-like compounds and to have a reduced aryl hydrocarbon receptor (AhR) signaling response. Little is known about the responses of these fish to non-dioxin-like PCBs, which are at extraordinarily high levels in NBH fish. In mammals, some non-dioxin-like PCB congeners act through nuclear receptor 1I2, the pregnane-X-receptor (PXR). To explore this pathway in killifish, a PXR cDNA was sequenced and its molecular phylogenetic relationship to other vertebrate PXRs was determined. Killifish were also collected in 2009 from NBH and SC, and after four months in the laboratory they were injected with a single dose of either the dioxin-like PCB 126 (an AhR agonist) or the non-dioxin-like PCB 153 (a mammalian PXR agonist). Gills and liver were sampled three days after injection and transcript levels of genes encoding PXR, cytochrome P450 3A (CYP3A), P-glycoprotein (Pgp), AhR2 and cytochrome P450 1A (CYP1A) were measured by quantitative PCR. As expected, there was little effect of PCB exposure on mRNA expression of

Regulation of pregnane-X-receptor, CYP3A and P-glycoprotein genes in the PCB-resistant killifish (Fundulus heteroclitus) population from New Bedford Harbor

Energy Technology Data Exchange (ETDEWEB)

Gräns, Johanna; Wassmur, Britt; Fernández-Santoscoy, María [Department of Biological and Environmental Sciences, University of Gothenburg, Box 463, SE 405 30 Gothenburg (Sweden); Zanette, Juliano; Woodin, Bruce R.; Karchner, Sibel I. [Biology Department, MS #32, Woods Hole Oceanographic Institution, Woods Hole, MA 02543 (United States); Nacci, Diane E.; Champlin, Denise; Jayaraman, Saro [Office of Research and Development, National Health and Environmental Effects Research Laboratory, Atlantic Ecology Division, United States Environmental Protection Agency, 27 Tarzwell Drive, Narragansett, RI 02882 (United States); Hahn, Mark E.; Stegeman, John J. [Biology Department, MS #32, Woods Hole Oceanographic Institution, Woods Hole, MA 02543 (United States); Celander, Malin C., E-mail: malin.celander@gu.se [Department of Biological and Environmental Sciences, University of Gothenburg, Box 463, SE 405 30 Gothenburg (Sweden)

2015-02-15

Highlights: • Basal levels of PXR and Pgp mRNA are lower in liver of fish from NBH than from SC. • Hepatic PXR, CYP3A and Pgp mRNA levels are induced by PCB in fish from NBH. • Both non-dioxin-like and dioxin-like PCBs induce PXR, CYP3A and Pgp in NBH fish. • Branchial PXR and CYP3A mRNA levels are induced by PCB 126 in fish from SC. • There is possible cross-talk between AhR and PXR signaling in killifish. - Abstract: Killifish survive and reproduce in the New Bedford Harbor (NBH) in Massachusetts (MA), USA, a site severely contaminated with polychlorinated biphenyls (PCBs) for decades. Levels of 22 different PCB congeners were analyzed in liver from killifish collected in 2008. Concentrations of dioxin-like PCBs in liver of NBH killifish were ∼400 times higher, and the levels of non-dioxin-like PCBs ∼3000 times higher than in killifish from a reference site, Scorton Creek (SC), MA. The NBH killifish are known to be resistant to the toxicity of dioxin-like compounds and to have a reduced aryl hydrocarbon receptor (AhR) signaling response. Little is known about the responses of these fish to non-dioxin-like PCBs, which are at extraordinarily high levels in NBH fish. In mammals, some non-dioxin-like PCB congeners act through nuclear receptor 1I2, the pregnane-X-receptor (PXR). To explore this pathway in killifish, a PXR cDNA was sequenced and its molecular phylogenetic relationship to other vertebrate PXRs was determined. Killifish were also collected in 2009 from NBH and SC, and after four months in the laboratory they were injected with a single dose of either the dioxin-like PCB 126 (an AhR agonist) or the non-dioxin-like PCB 153 (a mammalian PXR agonist). Gills and liver were sampled three days after injection and transcript levels of genes encoding PXR, cytochrome P450 3A (CYP3A), P-glycoprotein (Pgp), AhR2 and cytochrome P450 1A (CYP1A) were measured by quantitative PCR. As expected, there was little effect of PCB exposure on mRNA expression of

New EPA ban stymies Canadian exports of PCB waste

International Nuclear Information System (INIS)

Anon.

1997-01-01

With reference to a 1996 EPA ruling permitting the importation to the USA of PCBs for incineration, a unanimous three-judge panel of the US Court of Appeals for the Ninth District in San Francisco ruled that the Environmental Protection Agency (EPA) did not have the authority to permit the import of PCB wastes into the USA for disposal. Prior to the decision, 35 applications from Canada to export some 37,000 tonnes of PCB to the USA for disposal have been approved. Canadian brokers are upset with the decision, claiming that the decision will create a virtual monopoly for Bovar Inc., of Calgary, the only PCB-disposal facility in Canada. The loss (at least for the time being) of the alternate disposal opportunity will likely have the effect of forcing Canadian customers to pay more for PCB disposal. The Canadian government is monitoring the situation and is waiting to see whether an appeal is filed against the ruling

Bulk and edge spin transport in topological magnon insulators

Science.gov (United States)

Rückriegel, Andreas; Brataas, Arne; Duine, Rembert A.

2018-02-01

We investigate the spin transport properties of a topological magnon insulator, a magnetic insulator characterized by topologically nontrivial bulk magnon bands and protected magnon edge modes located in the bulk band gaps. Employing the Landau-Lifshitz-Gilbert phenomenology, we calculate the spin current driven through a normal metal |topological magnon insulator |normal metal heterostructure by a spin accumulation imbalance between the metals, with and without random lattice defects. We show that bulk and edge transport are characterized by different length scales. This results in a characteristic system size where the magnon transport crosses over from being bulk dominated for small systems to edge dominated for larger systems. These findings are generic and relevant for topological transport in systems of nonconserved bosons.

Experimental feeding of DDE and PCB to female big brown bats (Eptesicus fuscus)

Science.gov (United States)

Clark, D.R.; Prouty, R.M.

1977-01-01

Twenty-two female big brown bats (Eptesicus fuscus) were collected in a house attic in Montgomery County, Maryland. Seventeen were fed mealworms (Tenebrio molitor larvae) that contained 166 ppm DDE; the other five were fed uncontaminated mealworms. After 54 days of feeding, six dosed bats were frozen and the remaining 16 were starved to death. In a second experiment, 21 female big brown bats were collected in a house attic in Prince Georges County, Maryland. Sixteen were fed mealworms that contained 9.4 ppm Aroclor 1254 (PCB). After 37 days, two bats had died, four dosed bats were frozen, and the remaining 15 were starved to death. Starvation caused mobilization of stored residues. After the feeding periods, average weights of all four groups (DDE-dosed, DDE control, PCB-dosed, PCB control) had increased. However, weights of DDE-dosed bats had increased significantly more than those of their contols, whereas weights of PCB-dosed bats had increased significantly less than those of their controls. During starvation, PCB-dosed bats lost weight significantly more slowly than controls. Because PCB levels in dosed bats resembled levels found in some free-living big brown bats, PCBs may be slowing metabolic rates of some free-living bats. It is not known how various common organochlorine residues may affect metabolism in hibernating bats. DDE and PCB increased in brains of starving bats as carcass fat was metabolized. Because the tremors and/or convulsions characteristic of neurotoxicity were not observed, we think even the maximum brain levels attained (132 ppm DDE, 20 ppm PCB) were sublethal. However, extrapolation of our DDE data predicted lethal brain levels when fat reserves declined sufficiently. PCB-dosed bats were probably in no danger of neurotoxic poisoning. However, PCB can kill by a nonneurotoxic mode, and this could explain the deaths of two bats on PCB dosage.

PCB usage at the Grand Junction Area Office Facility. Final report

International Nuclear Information System (INIS)

Miller, M.E.; Donivan, S.

1982-06-01

The development, implementation, and results of the polychlorinated biphenyl (PCB) identification project at the Grand Junction Area Office (GJAO) are summarized. Methodology for the PCB analysis is described, and results are tabulated. Of the 51 transformers and disconnects in use at GJAO, 15 unites were determined to be PCB-contaminated or filled with PCBs. This number falls within EPA's estimate of 25 to 40 percent of all transformers in use being at least contaminated. Approximately 324 gallons of PCBs and 515 gallons of PCB-contaminated fluids are being used currently. No contaminated transformers or disconnects are in a position to contaminate food or feed products at the facility

40 CFR 261.8 - PCB wastes regulated under Toxic Substance Control Act.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 25 2010-07-01 2010-07-01 false PCB wastes regulated under Toxic... (CONTINUED) SOLID WASTES (CONTINUED) IDENTIFICATION AND LISTING OF HAZARDOUS WASTE General § 261.8 PCB wastes regulated under Toxic Substance Control Act. The disposal of PCB-containing dielectric fluid and electric...

Radiation dechlorination of PCE and PCB in the quarter operation flow apparatus

International Nuclear Information System (INIS)

Mucka, V.; Silber, R.; Pospisil, M.; Camra, M.; Bartonicek, B.

1999-01-01

The aim of this work was to verify practical possibilities of radiation dechlorination of liquid chlorinated substrates [perchloroethylene (PCE) and polychlorinated biphenyls (PCB)] in the quarter operation flow apparatus. In this apparatus may be disposable work over 50 dm 3 of media. Radiation dechlorination of PCE proceeds more effectively as dechlorination of PCB in flow regimes, too. Radiation chemical yield of G(-OH - ) decrease with increasing applied radiation dose and at the dose 5 kGy for PCE it is 200 · 10 -2 eV -1 and for PCB this value is 55 · 10 -2 eV -1 . At increasing original concentration of PCE or PCB the G-values decreases. The radical chain mechanism of dechlorination of PCE and PCB was proposed

Meta-analysis of pemetrexed plus carboplatin doublet safety profile in first-line non-squamous non-small cell lung cancer studies.

Science.gov (United States)

Okamoto, Isamu; Schuette, Wolfgang H W; Stinchcombe, Thomas E; Rodrigues-Pereira, José; San Antonio, Belén; Chen, Jian; Liu, Jingyi; John, William J; Zinner, Ralph G

2017-05-01

This meta-analysis compared safety profiles (selected drug-related treatment-emergent adverse events [TEAEs]) of first-line pemetrexed plus carboplatin (PCb) area under the concentration-time curve 5 mg/min•mL (PCb5) or 6 mg/min•mL (PCb6), two widely used regimens in clinical practice for advanced non-squamous non-small cell lung cancer. All patients received pemetrexed 500 mg/m 2 every 21 days with either of two carboplatin doses for up to 4-6 cycles. Safety profiles of PCb doses were compared using three statistical analysis methods: frequency table analysis (FTA), generalized linear mixed effect model (GLMM), and the propensity score method. Efficacy outcomes of PCb5 and PCb6 regimens were summarized. A total of 486 patients mainly from the US, Europe, and East Asia were included in the analysis; 22% (n = 105) received PCb5 in one trial and 78% (n = 381) received PCb6 in four trials. The FTA comparison demonstrated that PCb5 vs PCb6 was associated with a statistically significantly lower incidence of TEAEs, including all-grade thrombocytopenia, anemia, fatigue, and vomiting, and grade 3/4 thrombocytopenia. In the GLMM analysis, PCb5 patients were numerically less likely to experience all-grade and grade 3/4 neutropenia, anemia, and thrombocytopenia. The propensity score regression analysis showed PCb5 group patients were significantly less likely than PCb6 group patients to experience all-grade hematologic TEAEs and grade 3/4 thrombocytopenia and anemia. After applying propensity score 1:1 matching, FTA analysis showed that the PCb5 group had significantly less all-grade and grade 3/4 hematologic toxicities. Overall efficacy outcomes, including overall survival, progression-free survival, and response rate, were similar between the two carboplatin doses. Acknowledging the limitations of this meta-analysis of five trials, heterogeneous in patient's characteristics and trial designs, the results show that the PCb5 regimen was generally associated

STRUCTURAL INTERACTIONS OF HYDROGEN WITH BULK AMORPHOUS MICROSTRUCTURES IN METALLIC SYSTEMS UNDERSTANDING THE ROLE OF PARTIAL CRYSTALLINITY ON PERMEATION AND EMBRITTLEMENT

Energy Technology Data Exchange (ETDEWEB)

Brinkman, Kyle; Fox, Elise; Korinko, Paul; Adams, Thad

2010-05-10

The development of metallic glasses in bulk form has led to a resurgence of interest into the utilization of these materials for a variety of applications. A potentially exciting application for these bulk metallic glass (BMG) materials is their use as composite membranes to replace high cost Pd/Pd-alloy membranes for enhanced gas separation processes. One of the major drawbacks to the industrial use of Pd/Pd-alloy membranes is that during cycling above and below a critical temperature an irreversible change takes place in the palladium lattice structure which can result in significant damage to the membrane. Furthermore, the cost associated with Pd-based membranes is a potential detractor for their continued use and BMG alloys offer a potentially attractive alternative. Several BMG alloys have been shown to possess high permeation rates, comparable to those measured for pure Pd metal. In addition, high strength and toughness when either in-situ or ex-situ second phase dispersoids are present. Both of these properties, high permeation and high strength/toughness, potentially make these materials attractive for gas separation membranes that could resist hydrogen 'embrittlement'. However, a fundamental understanding of the relationship between partially crystalline 'structure'/devitrification and permeation/embrittlement in these BMG materials is required in order to determine the operating window for separation membranes and provide additional input to the material synthesis community for improved alloy design. This project aims to fill the knowledge gap regarding the impact of crystallization on the permeation properties of metallic glass materials. The objectives of this study are to (i) determine the crystallization behavior in different gas environments of Fe and Zr based commercially available bulk metallic glass and (ii) quantify the effects of partial crystallinity on the hydrogen permeation properties of these metallic glass membranes.

Beyond packing of hard spheres: The effects of core softness, non-additivity, intermediate-range repulsion, and many-body interactions on the glass-forming ability of bulk metallic glasses

Energy Technology Data Exchange (ETDEWEB)

Zhang, Kai; Fan, Meng; Liu, Yanhui; Schroers, Jan [Department of Mechanical Engineering and Materials Science, Yale University, New Haven, Connecticut 06520 (United States); Center for Research on Interface Structures and Phenomena, Yale University, New Haven, Connecticut 06520 (United States); Shattuck, Mark D. [Department of Mechanical Engineering and Materials Science, Yale University, New Haven, Connecticut 06520 (United States); Department of Physics and Benjamin Levich Institute, The City College of the City University of New York, New York, New York 10031 (United States); O’Hern, Corey S. [Department of Mechanical Engineering and Materials Science, Yale University, New Haven, Connecticut 06520 (United States); Center for Research on Interface Structures and Phenomena, Yale University, New Haven, Connecticut 06520 (United States); Department of Physics, Yale University, New Haven, Connecticut 06520 (United States); Department of Applied Physics, Yale University, New Haven, Connecticut 06520 (United States)

2015-11-14

When a liquid is cooled well below its melting temperature at a rate that exceeds the critical cooling rate R{sub c}, the crystalline state is bypassed and a metastable, amorphous glassy state forms instead. R{sub c} (or the corresponding critical casting thickness d{sub c}) characterizes the glass-forming ability (GFA) of each material. While silica is an excellent glass-former with small R{sub c} < 10{sup −2} K/s, pure metals and most alloys are typically poor glass-formers with large R{sub c} > 10{sup 10} K/s. Only in the past thirty years have bulk metallic glasses (BMGs) been identified with R{sub c} approaching that for silica. Recent simulations have shown that simple, hard-sphere models are able to identify the atomic size ratio and number fraction regime where BMGs exist with critical cooling rates more than 13 orders of magnitude smaller than those for pure metals. However, there are a number of other features of interatomic potentials beyond hard-core interactions. How do these other features affect the glass-forming ability of BMGs? In this manuscript, we perform molecular dynamics simulations to determine how variations in the softness and non-additivity of the repulsive core and form of the interatomic pair potential at intermediate distances affect the GFA of binary alloys. These variations in the interatomic pair potential allow us to introduce geometric frustration and change the crystal phases that compete with glass formation. We also investigate the effect of tuning the strength of the many-body interactions from zero to the full embedded atom model on the GFA for pure metals. We then employ the full embedded atom model for binary BMGs and show that hard-core interactions play the dominant role in setting the GFA of alloys, while other features of the interatomic potential only change the GFA by one to two orders of magnitude. Despite their perturbative effect, understanding the detailed form of the intermetallic potential is important for

Polychlorinated biphenyl (PCB) contamination in Galveston Bay, Texas: Comparing concentrations and profiles in sediments, passive samplers, and fish.

Science.gov (United States)

Oziolor, Elias M; Apell, Jennifer N; Winfield, Zach C; Back, Jeffrey A; Usenko, Sascha; Matson, Cole W

2018-05-01

The industrialized portion of the Houston Ship Channel (HSC) is heavily contaminated with anthropogenic contaminants, most prominent of which are the polychlorinated biphenyls (PCBs). This contamination has driven adaptive evolution in a keystone species for Galveston Bay, the Gulf killifish (Fundulus grandis). We investigated the geographical extent of PCB impacts by sampling 12 sites, ranging from the heavily industrialized upper portion of the HSC to Galveston Island. At each site, PCB concentrations and profiles were determined in three environmental compartments: sediment, water (polyethylene passive samplers), and fish tissue (resident Gulf killifish). We observed a steep gradient of PCB contamination, ranging from 4.00 to 100,000 ng/g organic carbon in sediment, 290-110,000 ng/g lipid in fish, and 4.5-2300 ng/g polyethylene in passive samplers. The PCB congener profiles in Gulf killifish at the most heavily contaminated sites were shifted toward the higher chlorinated PCBs and were highly similar to the sediment contamination profiles. In addition, while magnitude of total PCB concentrations in sediment and total fish contamination levels were highly correlated between sites, the relative PCB congener profiles in fish and passive samplers were more alike. This strong correlation, along with a lack of dependency of biota-sediment accumulation factors with total contamination rates, confirm the likely non-migratory nature of Gulf killifish and suggest their contamination levels are a good site-specific indicator of contamination in the Galveston Bay area. The spatial gradient of PCB contamination in Galveston Bay was evident in all three matrices studied and was observed effectively using Gulf killifish contamination as an environmentally relevant bioindicator of localized contamination in this environment. Copyright © 2018 Elsevier Ltd. All rights reserved.

Cell specific effects of PCB 126 on aryl hydrocarbone receptors in follicular cells of porcine ovaries

Energy Technology Data Exchange (ETDEWEB)

Wojtowicz, A.; Augustowska, K.; Gregoraszczuk, E. [Lab. of Physiology and Toxicology of Reproduction, Dept. of Animal Physiology, Inst. of Zoology, Jagiellonian Univ., Krakow (Poland)

2004-09-15

Polychlorinated biphenyles (PCBs) like other endocrine disrupters could interfere with natural hormones by binding to their receptors and thus mimicking the cellular response to them. They are known to possess either estrogenic or antiestrogenic properties. In our previous papers we demonstrated that PCBs are able to disrupt ovarian steroidogenesis. We found that the coplanar PCB 126 caused the decrease in estradiol secretion in whole cultured pig ovarian follicles. PCB 126 congener is structurally related to 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD). Since TCDD effects are known to be mediated by aryl hydrocarbone receptors (AhRs), we decided to determine if PCB 126 affects signal transduction pathway activated by these receptors. It has been reported that the functional AhR is present in ovary including oocytes, granulosa and theca cells of rat, mouse, rhesus monkey and human ovary. Moreover, the expression of AhR in the rat ovary appeared to be estrous cycle-dependent, thus suggesting that AhR expression may be regulated by fluctuating hormone levels. This study was designed to investigate the effects of the non-ortho-substituted 3,3',4,4',5-pentachlorobiphenyl (PCB126) on the AhR activation, localization and protein level in pig ovarian follicle cells.

Relationships between Atmospheric Transport Regimes and PCB Concentrations in the Air at Zeppelin, Spitsbergen.

Science.gov (United States)

Ubl, Sandy; Scheringer, Martin; Hungerbühler, Konrad

2017-09-05

Polychlorinated biphenyls (PCBs) are persistent hazardous chemicals that are still detected in the atmosphere and other environmental media, although their production has been banned for several decades. At the long-term monitoring site, Zeppelin at Spitsbergen, different PCB congeners have been continuously measured for more than a decade. However, it is not clear what factors determine the seasonal and interannual variability of different (lighter versus heavier) PCB congeners. To investigate the influence of atmospheric transport patterns on PCB-28 and PCB-101 concentrations at Zeppelin, we applied the Lagrangian Particle Dispersion Model FLEXPART and calculated "footprints" that indicate the potential source regions of air arriving at Zeppelin. By means of a cluster analysis, we assigned groups of similar footprints to different transport regimes and analyzed the PCB concentrations according to the transport regimes. The concentrations of both PCB congeners are affected by the different transport regimes. For PCB-101, the origin of air masses from the European continent is primarily related to high concentrations; elevated PCB-101 concentrations in winter can be explained by the high frequency of this transport regime in winter, whereas PCB-101 concentrations are low when air is arriving from the oceans. For PCB-28, in contrast, concentrations are high during summer when air is mainly arriving from the oceans but low when air is arriving from the continents. The most likely explanation of this finding is that local emissions of PCB-28 mask the effect of long-range transport and determine the concentrations measured at Zeppelin.

Enhancement of room-temperature plasticity in a bulk metallic glass by finely dispersed porosity

International Nuclear Information System (INIS)

Wada, Takeshi; Inoue, Akihisa; Greer, Alan Lindsay

2005-01-01

Melts of Pd 42.5 Cu 30 Ni 7.5 P 20 (at. %) held under pressurized hydrogen are cast into bulk metallic glass (BMG) rods with fine (20-30 μm diameter) pores uniformly dispersed. The low overall porosities ( -3 , compared to 16 MJ m -3 for the pore-free BMG. The pores force the proliferation of shear bands below the overall failure stress, a process of interest for toughening BMGs, materials for which shear localization in deformation restricts structural applications

Machine Vision Implementation in Rapid PCB Prototyping

Directory of Open Access Journals (Sweden)

Yosafat Surya Murijanto

2012-03-01

Full Text Available Image processing, the heart of machine vision, has proven itself to be an essential part of the industries today. Its application has opened new doorways, making more concepts in manufacturing processes viable. This paper presents an application of machine vision in designing a module with the ability to extract drills and route coordinates from an un-mounted or mounted printed circuit board (PCB. The algorithm comprises pre-capturing processes, image segmentation and filtering, edge and contour detection, coordinate extraction, and G-code creation. OpenCV libraries and Qt IDE are the main tools used. Throughout some testing and experiments, it is concluded that the algorithm is able to deliver acceptable results. The drilling and routing coordinate extraction algorithm can extract in average 90% and 82% of the whole drills and routes available on the scanned PCB in a total processing time of less than 3 seconds. This is achievable through proper lighting condition, good PCB surface condition and good webcam quality. 

Development of friction welding process of Zr-based bulk metallic glasses

International Nuclear Information System (INIS)

Shin, Hyung Seop; Jeong, Young Jin; Kim, Ki Hyun

2004-01-01

Bulk Metallic Glasses(BMG) with good mechanical properties have problems that engineering application fields have been limited because of limitation of the alloy size. In order to solving this problem, the friction welding of BMG has been tried using the superplastic-like deformation behavior under the supercooled liquid region. The apparatus for friction welding test was designed and constructed using pneumatic cylinder and gripper based on a conventional lathe. Friction welding have been tried to combination of same BMG alloy and crystalline alloys. The results of welding test were evaluated by X-ray diffraction, measurement of hardness and mechanical properties test. In order to obtain the optimized welding test conditions the temperature of friction interface was measured using Infrared thermal imager

Coulombic Fluids Bulk and Interfaces

CERN Document Server

Freyland, Werner

2011-01-01

Ionic liquids have attracted considerable interest in recent years. In this book the bulk and interfacial physico-chemical characteristics of various fluid systems dominated by Coulomb interactions are treated which includes molten salts, ionic liquids as well as metal-molten salt mixtures and expanded fluid metals. Of particular interest is the comparison of the different systems. Topics in the bulk phase concern the microscopic structure, the phase behaviour and critical phenomena, and the metal-nonmetal transition. Interfacial phenomena include wetting transitions, electrowetting, surface freezing, and the electrified ionic liquid/ electrode interface. With regard to the latter 2D and 3D electrochemical phase formation of metals and semi-conductors on the nanometer scale is described for a number of selected examples. The basic concepts and various experimental methods are introduced making the book suitable for both graduate students and researchers interested in Coulombic fluids.

Sediment pore water distribution coefficients of PCB congeners in enriched black carbon sediment

International Nuclear Information System (INIS)

Martinez, Andres; O'Sullivan, Colin; Reible, Danny; Hornbuckle, Keri C.

2013-01-01

More than 2300 sediment pore water distribution coefficients (K PCBids ) of 93 polychlorinated biphenyls (PCBs) were measured and modeled from sediments from Indiana Harbor and Ship Canal. K PCBids were calculated from previously reported bulk sediment values and newly analyzed pore water. PCBs in pore waters were measured using SPME PDMS-fiber and ∑PCB ranged from 41 to 1500 ng L −1 . The resulting K PCBids were ∼1 log unit lower in comparison to other reported values. A simple model for the K PCBid consisted of the product of the organic carbon fraction and the octanol–water partition coefficient and provided an excellent prediction for the measured values, with a mean square error of 0.09 ± 0.06. Although black carbon content is very high in these sediments and was expected to play an important role in the distribution of PCBs, no improvement was obtained when a two-carbon model was used. -- Highlights: •PCB sediment-pore water distribution coefficients were measured and modeled. •Distribution coefficients were lower in comparison to other reported values. •Organic carbon fraction times the K OW yielded the best prediction model. •The incorporation of black carbon into a model did not improve the results. -- The organic carbon fraction times the octanol–water partition coefficient yielded the best prediction model for the sediment pore water distribution coefficient of PCBs

PCB management at Manitoba Hydro's Waverley Service Centre

International Nuclear Information System (INIS)

Rempel, R.G.; Engstrom, T.

1996-01-01

Manitoba Hydro was the first Canadian utility to initiate a program to decontaminate insulating oil contaminated with polychlorinated biphenyls (PCBs). This paper describes Manitoba Hydro's recovery, reuse and recycling program, operated out of the utility's Waverley Service Centre (WSC). The WSC is a central facility serving to phase out and and destroy PCBs which remain in Manitoba Hydro's electrical system. Several hundred thousand litres of PCB-contaminated insulating oil are decontaminated annually at the WSC. The decontaminated oil is then reconditioned for reuse within the system operations. A PCBX unit was purchased from Sun Ohio for the decontamination of insulating oils containing PCBs. PCB decontamination is achieved through a chemical dechlorination treatment process. The PCBX treatment unit and the PCB storage building were described. 18 refs., 8 figs

Free volume model: High-temperature deformation of a Zr-based bulk metallic glass

International Nuclear Information System (INIS)

Bletry, M.; Guyot, P.; Blandin, J.J.; Soubeyroux, J.L.

2006-01-01

The homogeneous deformation of a zirconium-based bulk metallic glass is investigated in the glass transition region. Compression tests at different temperatures and strain rates have been conducted. The mechanical behavior is analyzed in the framework of the free volume model, taking into account the dependence of the flow defect concentration on deformation. The activation volume is evaluated and allows one to gather the viscosity data (for the different strain rates and temperatures) on a unique master curve. It is also shown that, due to the relation between flow defect concentration and free volume, it is not possible to deduce the equilibrium flow defect concentration directly from mechanical measurements. However, if this parameter is arbitrarily chosen, mechanical measurements give access to the other parameters of the model, these parameters for the alloy under investigation being of the same order of magnitude as those for other metallic glasses

Fast and parallel determination of PCB 77 and PCB 180 in plasma using ultra performance liquid chromatography with diode array detection: A pharmacokinetic study in Swiss albino mouse.

Science.gov (United States)

Ramanujam, N; Sivaselvakumar, M; Ramalingam, S

2017-11-01

A simple, sensitive and reproducible ultra-performance liquid chromatography (UPLC) method has been developed and validated for simultaneous estimation of polychlorinated biphenyl (PCB) 77 and PCB 180 in mouse plasma. The sample preparation was performed by simple liquid-liquid extraction technique. The analytes were chromatographed on a Waters Acquity H class UPLC system using isocratic mobile phase conditions at a flow rate of 0.3 mL/min and Acquity UPLC BEH shield RP 18 column maintained at 35°C. Quantification was performed on a photodiode array detector set at 215 nm and PCB 101 was used as internal standard (IS). PCB 77, PCB 180, and IS retention times were 2.6, 4.7 and 2.8 min, respectively, and the total run time was 6 min. The method was validated for specificity, selectivity, recovery, linearity, accuracy, precision and sample stability. The calibration curve was linear over the concentration range 10-3000 ng/mL for PCB 77 and PCB 180. Intra- and inter-day precisions for PCBs 77 and 180 were found to be good with CV <4.64%, and the accuracy ranged from 98.90 to 102.33% in mouse plasma. The validated UPLC method was successfully applied to the pharmacokinetic study of PCBs 77 and 180 in mouse plasma. Copyright © 2017 John Wiley & Sons, Ltd.

Effect of sonication on particle dispersion, administered dose and metal release of non-functionalized, non-inert metal nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Pradhan, Sulena; Hedberg, Jonas, E-mail: jhed@kth.se; Blomberg, Eva [KTH Royal Institute of Technology, Division of Surface and Corrosion Science, Department of Chemistry (Sweden); Wold, Susanna [KTH Royal Institute of Technology, Division of Applied Physical Chemistry, Department of Chemistry (Sweden); Odnevall Wallinder, Inger [KTH Royal Institute of Technology, Division of Surface and Corrosion Science, Department of Chemistry (Sweden)

2016-09-15

In this study, we elucidate the effect of different sonication techniques to efficiently prepare particle dispersions from selected non-functionalized NPs (Cu, Al, Mn, ZnO), and corresponding consequences on the particle dose, surface charge and release of metals. Probe sonication was shown to be the preferred method for dispersing non-inert, non-functionalized metal NPs (Cu, Mn, Al). However, rapid sedimentation during sonication resulted in differences between the real and the administered doses in the order of 30–80 % when sonicating in 1 and 2.56 g/L NP stock solutions. After sonication, extensive agglomeration of the metal NPs resulted in rapid sedimentation of all particles. DLVO calculations supported these findings, showing the strong van der Waals forces of the metal NPs to result in significant NP agglomeration. Metal release from the metal NPs was slightly increased by increased sonication. The addition of a stabilizing agent (bovine serum albumin) had an accelerating effect on the release of metals in sonicated solutions. For Cu and Mn NPs, the extent of particle dissolution increased from <1.6 to ~5 % after sonication for 15 min. A prolonged sonication time (3–15 min) had negligible effects on the zeta potential of the studied NPs. In all, it is shown that it is of utmost importance to carefully investigate how sonication influences the physico-chemical properties of dispersed metal NPs. This should be considered in nanotoxicology investigations of metal NPs.Graphical Abstract.

40 CFR 761.2 - PCB concentration assumptions for use.

Science.gov (United States)

2010-07-01

... dielectric fluid are unknown, any person must assume the transformer to be a PCB Transformer. (4) Any person must assume that a capacitor manufactured prior to July 2, 1979, whose PCB concentration is not established contains ≥500 ppm PCBs. Any person may assume that a capacitor manufactured after July 2, 1979, is...

Secondary defects in non-metallic solids

International Nuclear Information System (INIS)

Ashbee, K.H.G.; Hobbs, L.W.

1977-01-01

This paper points out features of secondary defect formation which are peculiar to non-metallic solids (excluding elemental semiconductors). Most of the materials of interest are compounds of two or more (usually more or less ionic) atomic species, and immediate consequence of which is a need to maintain both stoichiometry (or accommodate non-stoichiometry) and order. Primary defects in these solids, whether produced thermally, chemically or by irradiation, seldom are present or aggregate in exactly stoichiometric proportions, and the resulting extending defect structures can be quite distinct from those found in metallic solids. Where stoichiometry is maintained, it is often convenient to describe extended defects in terms of alterations in the arrangement of 'molecular' units. The adoption of this procedure enables several novel features of extended defect structures in non-metals to be explained. There are several ways in which a range of non-stoichiometry can be accommodated, which include structural elimination of point defects, nucleation of new coherent phases of altered stoichiometry, and decomposition. (author)

Cu-Zr-Ag bulk metallic glasses based on Cu8Zr5 icosahedron

International Nuclear Information System (INIS)

Xia Junhai; Qiang Jianbing; Wang Yingmin; Wang Qing; Dong Chuang

2007-01-01

Based on the cluster line criterion, the Ag addition into the Cu 8 Zr 5 cluster composition is investigated for the search of ternary Cu-Zr-Ag bulk metallic glasses with high glass forming abilities. Two initial binary compositions Cu 0.618 Zr 0.382 and Cu 0.64 Zr 0.36 are selected. The former one corresponds to a deep eutectic point; it is also the composition of the Cu 8 Zr 5 icosahedron, which is derived from the Cu 8 Zr 3 structure. The latter one, which can be regarded as the Cu 8 Zr 5 cluster plus a glue atom Cu, is the best glass-forming composition in the Cu-Zr binary system. Two composition lines (Cu 0.618 Zr 0.382 ) 1-x Ag x and (Cu 0.64 Zr 0.36 ) 1-x Ag x are thus constructed in the Cu-Zr-Ag system by linking these two compositions with the third constitute Ag. A series of Cu-Zr-Ag bulk metallic glasses are found with 2-8 at.% Ag contents in both composition lines. The optimum composition (Cu 0.618 Zr 0.382 ) 0.92 Ag 0.08 within the searched region with the highest T g /T l = 0.633, is located along the cluster line (Cu 0.618 Zr 0.382 ) 1-x Ag x , where the deep eutectic Cu 0.618 Zr 0.382 exactly corresponds to the dense packing cluster Cu 8 Zr 5 . The alloying mechanism is discussed in the light of atomic size and electron concentration factors

Evaluation of Ni-free Zr–Cu–Fe–Al bulk metallic glass for biomedical implant applications

Energy Technology Data Exchange (ETDEWEB)

Sun, Ying-Sui [Institute of Oral Biology, National Yang-Ming University, Taipei, Taiwan (China); Zhang, Wei [School of Materials Science and Engineering, Dalian University of Technology, Dalian (China); Kai, Wu [Institute of Materials Engineering, National Taiwan Ocean University, Keelung, Taiwan (China); Liaw, Peter K. [Department of Materials Science and Engineering, The University of Tennessee, Knoxville, TN (United States); Huang, Her-Hsiung, E-mail: hhhuang@ym.edu.tw [Institute of Oral Biology, National Yang-Ming University, Taipei, Taiwan (China); Department of Dentistry, National Yang-Ming University, Taipei, Taiwan (China); Department of Dentistry, Taipei City Hospital, Taipei, Taiwan (China); Department of Stomatology, Taipei Veterans General Hospital, Taipei, Taiwan (China)

2014-02-15

Highlights: ► A Zr{sub 62.5}Cu{sub 22.5}Fe{sub 5}Al{sub 10} bulk metallic glass (BMG) with 50 GPa elastic modulus was used. ► This Ni-free Zr-based BMG had lower metal ion release rate than the commercial Ti. ► This Ni-free Zr-based BMG had better proteins adsorption than the commercial Ti. ► This Ni-free Zr-based BMG has a high potential for biomedical implant applications. -- Abstract: This study was conducted to investigate the surface characteristics, including the chemical composition, metal ion release, protein adsorption, and cell adhesion, of a Ni-free Zr-based (Zr{sub 62.5}Cu{sub 22.5}Fe{sub 5}Al{sub 10}) bulk metallic glass (BMG) with low elastic modulus for biomedical implant applications. X-ray photoelectron spectroscopy was used to identify the surface chemical composition and the protein (albumin and fibronectin) adsorption of the specimen. The metal ions released from the specimen in simulated blood plasma and artificial saliva solutions were measured using an inductively coupled plasma-mass spectrometer. The cell adhesion, in terms of the morphology, focal adhesion complex, and skeletal arrangement, of human bone marrow mesenchymal stem cells was evaluated using scanning electron microscope observations and immunofluorescent staining. For comparison purposes, the above-mentioned tests were also carried out on the widely used biomedical metal, Ti. The results showed that the main component on the outermost surface of the amorphous Zr{sub 62.5}Cu{sub 22.5}Fe{sub 5}Al{sub 10} BMG was ZrO{sub 2} with small amounts of Cu, Al, and Fe oxides. The released metal ions from Zr{sub 62.5}Cu{sub 22.5}Fe{sub 5}Al{sub 10} BMG were well below the critical concentrations that cause negative biological effects. The Zr{sub 62.5}Cu{sub 22.5}Fe{sub 5}Al{sub 10} BMG had a greater adsorption capacity for albumin and fibronectin than that of commercial biomedical Ti. The Zr{sub 62.5}Cu{sub 22.5}Fe{sub 5}Al{sub 10} BMG surface showed an attached cell number similar

Do fish growth rates correlate with PCB body burdens?

Science.gov (United States)

Andrew L. Rypel; David R.. Bayne

2010-01-01

We evaluated whether growth rates of six fish species correlated with PCB concentrations in a moderately-to-heavily polluted freshwater ecosystem. Using a large dataset (n ¼ 984 individuals), and after accounting for growth effects related to fish age, habitat, sex, and lipids, growth correlated significantly, but positively with lipid-corrected PCB concentrations for...

Facile conversion of bulk metal surface to metal oxide single-crystalline nanostructures by microwave irradiation: Formation of pure or Cr-doped hematite nanostructure arrays

International Nuclear Information System (INIS)

Cho, Seungho; Jeong, Haeyoon; Lee, Kun-Hong

2010-01-01

We report a method for converting the surfaces of bulk metal substrates (pure iron or stainless steel) to metal oxide (hematite or Cr-doped hematite) nanostructures using microwave irradiation. When microwave radiation (2.45 GHz, single-mode) was applied to a metal substrate under the flow of a gas mixture containing O 2 and Ar, metal oxide nanostructures formed and entirely covered the substrate. The nanostructures were single crystalline, and the atomic ratios of the substrate metals were preserved in the nanostructures. When a pure iron sheet was used as a substrate, hematite nanowires (1000 W microwave radiation) or nanosheets (1800 W microwave radiation) formed on the surface of the substrate. When a SUS410 sheet was used as a substrate, slightly curved rod-like nanostructures were synthesized. The oxidation states of Fe and Cr in these nanorods were Fe 3+ and Cr 3+ . Quantitative analyses revealed an average Fe/Cr atomic ratio of 9.2, nearly identical to the ratio of the metals in the SUS410 substrate.

Characterization of mechanically alloyed Ti-based bulk metallic glass composites containing carbon nanotubes

Energy Technology Data Exchange (ETDEWEB)

Hsu, C.F. [Institute of Materials Engineering, National Taiwan Ocean University, No. 2, Beining Road, Keelung (China); Lin, H.M. [Department of Materials Engineering, Tatung University, No.40, Sec. 3, Jhongshan N. Rd. Jhongshan District, Taipei 104 Taiwan (China); Lee, P.Y.

2008-11-15

This study explored the feasibility of preparing CNT/Ti{sub 50}Cu{sub 28}Ni{sub 15}Sn{sub 7} bulk metallic glass (BMG) composites though powder metallurgy route. The CNT/Ti{sub 50}Cu{sub 28}Ni{sub 15}Sn{sub 7} BMG composites were obtained by consolidating the 8h mechanically alloyed composite powders by vacuum hot pressing process. A significant increase in hardness (9.34 GPa) and fracture strength (1937 MPa) was achieved for the Ti{sub 50}Cu{sub 28}Ni{sub 15}Sn{sub 7} BMG composites containing 12 vol. % CNT. (Abstract Copyright [2008], Wiley Periodicals, Inc.)

Nanoindentation studies on Cu-Ti-Zr-Ni-Si-Sn bulk metallic glasses

International Nuclear Information System (INIS)

Mukhopadhyay, N.K.; Belger, A.; Paufler, P.; Kim, D.H.

2007-01-01

In the present investigation, Cu 47 Ti 33 Ni 6 Sn 2 Si 1 (numbers indicate at.%) bulk metallic glass (BMG), fabricated by injection casting has been used for indentation experiments. Microindentation and nanoindentation tests were conducted to study the indentation responses of this material. The nanohardness and the Young's modulus were calculated following the standard procedure in literature. Around the indent, shear bands can be clearly observed under scanning electron microscopy examination. Atomic-force microscopy shows the pile of the material in a step-wise manner. The thinned sample near the indent shows the evolution of nanocrystals (∼20-30 nm) by transmission electron microscopy. During nanoindentation (in single- and multi-indent mode) experiments, the load-displacement P-h curves show displacement bursts, which are also known as pop-ins or serrations. The total displacement during indentation can be accounted for by sum total effect of the individual displacement of all the displacement-bursts observed in the P-h curve. Thus the plastic deformation of this glassy material appears to proceed in a discrete manner unlike ductile metallic alloys

Occurrence of NDL-PCB in food and feed in Europe

Energy Technology Data Exchange (ETDEWEB)

Gallani, B. [UK Food Standards Agency, London (United Kingdom); Boix, A. [European Commission, DG JRC IRMM FSQ, Geel (Belgium); Domenico, A. di [Italian National Institute of Health, Rome (Italy); Fanelli, R. [Mario Negri Institute for Pharmacological Research, Milano (Italy)

2004-09-15

Polychlorinated Biphenyls (PCBs) cover a group of 209 different congeners, which can be divided into two groups according to their toxicological properties. One group consists of 12 congeners that show toxicological properties similar to dioxins and are therefore termed ''dioxin-like PCBs''. The other PCBs, sometimes termed ''non dioxin-like PCBs'', do not show dioxin-like toxicity but have another toxicological profile The Scientific Committee on Food (SCF) assessed the risks for public health arising from the presence of dioxins and dioxin-like PCBs in food in November 2000 and May 2001. The Scientific Committee on Animal Nutrition (SCAN) adopted on 6 November 2000 an opinion on the dioxin contamination of feedingstuffs and their contribution to the contamination of food of animal origin. These opinions provided the scientific basis for the Community measures to limit the presence of these contaminants in feed and food as part of an overall strategy to reduce the presence of dioxins, furans and PCBs in the environment, food and feed. A significant part of the human exposure to PCBs derives from food. Food of animal origin is the main contributor to dietary PCB exposure. The PCB burden in animals derives mainly from feed. This paper provides some information on background levels of non-dioxin-like PCBs in food and feed and might assist in the calculation of exposure of the EU population to these contaminants, including the identification of the main sources of dietary exposure and the relative importance of dietary and non dietary sources.

Laboratory Study of Polychlorinated Biphenyl (PCB) Contamination and Mitigation in Buildings -- Part 4. Evaluation of the Activated Metal Treatment System (AMTS) for On-site Destruction of PCBs

Science.gov (United States)

This is the fourth, also the last, report of the report series entitled “Laboratory Study of Polychlorinated Biphenyl (PCB) Contamination and Mitigation in Buildings.” This report evaluates the performance of an on-site PCB destruction method, known as the AMTS method, developed ...

Metastability and thermophysical properties of metallic bulk glass forming alloys

International Nuclear Information System (INIS)

Wunderlich, R.K.; Fecht, H.J.

1998-01-01

The absence of crystallization over a wide time/temperature window can be used to produce bulk metallic glass by relatively slow cooling of the melt. For a number of alloys, including several multicomponent Zr-based alloys, the relevant thermodynamic and thermomechanical properties of the metastable glassy and undercooled liquid states have been measured below and above the glass transition temperature. These measurements include specific heat, viscosity, volume, and elastic properties as a function of temperature. As a result, it becomes obvious that the maximum undercooling for these alloys is given by an isentropic condition before an enthalpic or isochoric instability is reached. Alternatively, these glasses can also be produced by mechanical alloying, thus replacing the thermal disorder by static disorder and resulting in the same thermodynamic glass state. During heating through the undercooled liquid, a nanoscale phase separation occurs for most glasses as a precursor of crystallization

Compressive behavior of wire reinforced bulk metallic glass matrix composites

Energy Technology Data Exchange (ETDEWEB)

Lee, Seung-Yub [Department of Materials Science, M/C 138-78, California Institute of Technology, Pasadena, CA 91125 (United States); Clausen, Bjorn [Lujan Neutron Science Center, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Uestuendag, Ersan [Department of Materials Science and Engineering, Iowa State University, Ames, IA 50011 (United States)]. E-mail: ustundag@iastate.edu; Choi-Yim, Haein [Department of Materials Science, M/C 138-78, California Institute of Technology, Pasadena, CA 91125 (United States); Aydiner, C. Can [Department of Materials Science and Engineering, Iowa State University, Ames, IA 50011 (United States); Bourke, Mark A.M. [Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States)

2005-06-15

Bulk metallic glasses (BMGs) possess a unique set of mechanical properties that make them attractive structural materials. However, when loaded without constraint, BMGs fracture catastrophically due to formation of macroscopic shear bands and this behavior reduces their reliability. To address this issue, BMG matrix composites have been developed. In this investigation, neutron diffraction was used during uniaxial compressive loading to measure the internal strains in the second phases of various BMG composites reinforced with Ta, Mo, or stainless steel wires. The diffraction data were then employed to develop a finite element model that deduced the in situ constitutive behavior of each phase. It was found that the reinforcements yielded first and started transferring load to the matrix, which remained elastic during the whole experiment. While the present composites exhibited enhanced ductility, largely due to their ductile reinforcements, they yielded at applied stresses lower than those found in W reinforced composites.

FeNbB bulk metallic glass with high boron content

Energy Technology Data Exchange (ETDEWEB)

Stoica, M.; Das, Jayanta; Eckert, Juergen [IFW Dresden, Institute for Complex Materials, P.O. Box 270016, D-01171 Dresden (Germany); Hajlaoui, Khalil; Yavari, Alain Reza [LTPCM-CNRS, I.N.P. Grenoble, 1130 Rue de la Piscine, BP 75, F-38402 University Campus (France)

2007-07-01

Fe-based alloys able to form magnetic bulk metallic glasses (BMGs) are of the type transition metal - metalloid and often contain 5 or more elements. Usually, the metalloid content is around 20 atomic %. Very recently, the Fe{sub 66}Nb{sub 4}B{sub 30} alloy was found to be able to form BMG by copper mold casting technique, despite its high metalloid content. Several composition with boron contents around 30 at. % or even higher were calculated since 1993 as possible compositions of the remaining amorphous matrix after the first stage of nanocrystallization of Finemet-type Fe{sub 77}Si{sub 14}B{sub 9} glassy ribbons with 0.5 to 1 atomic % Cu and a few percent Nb addition. Melt-spun ribbons of all calculated compositions were found to be glassy. The composition of the ternary Fe-based BMG investigated in the present study resulted as an optimization of all possibilities. The alloy is ferromagnetic with glass transition temperature T{sub g}=845 K, crystallisation temperature T{sub x}=876 K, liquidus temperature T{sub liq}=1451 K and mechanical strength of 4 GPa. The coercivity of as-cast samples is very low, around 1.5 A/m. The present contribution aims at discussing the thermal stability, mechanical and magnetic properties of the Fe{sub 66}Nb{sub 4}B{sub 30} BMG.

Assessment of the Polychlorinated Biphenyl (PCB Occurrence in Copper Sulfates and the Influential Role of PCB Levels on Grapes.

Directory of Open Access Journals (Sweden)

Xiaomin Li

Full Text Available Copper sulfates (CuSO4 are widely used as the primary component of fungicides in the grape industry. The agricultural-grade CuSO4 that we collected from Chinese nationwide markets were found to be contaminated by polychlorinated dibenzo-p-dioxins and dibenzofurans and high levels of polychlorinated biphenyls (Σ19PCBs: 0.32~9.51 ng/g. In the following research, we studied the impact of CuSO4 application on PCB levels in grape products through a field experiment, and conducted a national survey to speculate the role that CuSO4 played on the occurrence of PCB in grapes. In the field experiment, an obvious increase of PCBs in grape leaves (from 174 to 250 pg/g fw was observed after Bordeaux mixture (the main component of which is CuSO4 application. As to the main PCB congener in CuSO4, the most toxic CB 126 (toxic equivalency factor = 0.1 also increased in grape peels (from 1.66 to 2.93 pg/g fw after pesticide spray. Both the correlation study and the principal component analysis indicated that environmental factors were dominant PCB contributors to grapes, and grapes from e-waste dismantling area containing the highest PCBs also proved the notion. It is worth noting that this report describes the first research examining PCBs in CuSO4 and its influence on agricultural products to date.

Tracking Polychlorinated Biphenyls (PCB) after an incident along a river system - Case study Elbe River

Science.gov (United States)

Kleisinger, Carmen; Dietrich, Stephan; Kehl, Nora; Claus, Evelyn; Schubert, Birgit

2017-04-01

In spring 2015, extremely high concentrations of Polychlorinated Biphenyls (PCB) well above the long-term average were detected in suspended particulate matter (SPM) within the River Elbe. They were released due to abrasive blasting of the old coating from a bridge in the upper part of the River, approximately 50 km upstream of the first measurement site. PCBs are persistent organic pollutants, preferentially bound to fine-grained fractions of the SPM. Results from monitoring of contaminants in SPM along the Elbe indicate the further dispersal of the PCB-contaminated sediments. These measurements include yearly investigations on PCB concentrations in sediments in the inner reaches of the Elbe, an additional longitudinal survey in 2015 and monthly monitoring of PCBs in SPM at stations along the river including the Elbe estuary (Germany). The Elbe estuary is of major economic importance since Hamburg harbour, one of the largest harbours in Europe, is located there. Maintaining the harbour includes dredging and, i.a., relocating large amounts of the dredged material within the water body. High PCB concentrations in sediments could lead to restrictions on the relocation of these sediments. This study aims at tracking the fate of PCB contaminated material released from the point source of the incident site along the whole river stretch and at estimating its impact on the quality of sediments and consequently on dredging activities in the estuary. The ratio of high (PCB 138, 152 and 180) versus low (PCB 28, 52, 101) chlorinated PCB congeners proved to be a suitable tracer to distinguish the PCB load released by the incident from the long-term background signals. As Delor 106/Clophen A60, which contains approx. 90% hexa- to decachloric congeners, was an additive in the coating of the bridge, the pattern of PCBs released by the incident is dominated by the highly chlorinated PCB-congeners PCB 138, 153 and 180. At the tidal weir Geesthacht, the entrance to the estuary, an

Concentrations of metals, PCB and dioxin and furans in fish and sediments of four lakes in Northern Quebec in 2001; Teneurs en metaux, en BPC et en dioxines et furanes dans les poissons et les sediments de quatre lacs du nord du Quebec en 2001

Energy Technology Data Exchange (ETDEWEB)

Laliberte, D.; Tremblay, G. [Quebec Ministere de l' Environnement, Quebec, PQ (Canada). Direction du Suivi de l' Etat de l' Environnement

2002-07-01

An environmental study was conducted on Chibougamau, aux Dores, Obatogamau, and Waconichi Lakes in northern Quebec in 2001. Those lakes are used by the Cree Indians for subsistence fishing and sport fishing by the rest of the Quebec population. Concentrations in heavy metals and polychlorinated biphenyls (PCB) were measured in sediments from Lakes Chibougamau and aux Dores. Heavy metals concentrations were also measured from two mining effluents and four waste samples originating from a mining waste location around the lakes. In addition, three fish species were sampled in those two lakes to evaluate the effect of mining activity on mercury levels in those species. The measurements were compared to those obtained from fish originating from Obatogamau and Waconichi Lakes. Finally, heavy metals, PCB, and dioxins and furans were measured in five fish species from the four lakes. The results of the analysis from the mining effluents revealed concentrations of the six metals included in directive 019 for the mining industry were lower than the authorized limits. However, a bio-essay performed in 2002 in the final effluent of the mining basin showed that the effluent from Copper Rand Mine presented toxicity and was not in agreement with the directive for this parameter. The sediments had low mercury concentrations. The highest concentration originated from the site near Henderson Mine I. None of the concentrations exceeded the limit and there are no negative effect expected on the fauna. Arsenic, cadmium, copper, nickel and zinc had high concentrations in sediments. The corresponding locations were near Copper Rand Mine, south of Principale Mine and at the foot of Principale Park. No PCB were detected in Chibougamau and aux Dores Lakes. Data does not indicate that the mining activity caused an increase in mercury levels in fish. Mercury levels in fish captured in 2001 in Chibougamau Lake were lower than those measured in 1999. 12 refs., 9 tabs., 12 figs.

Effect van PCB's op de energiekosten van migratie en bloedparameters van Europese aal

NARCIS (Netherlands)

Ginneken, van V.J.T.; Palstra, A.P.; Nieveen, M.; Berg, van den J.H.J.; Murk, A.J.

2005-01-01

Er zijn nog steeds PCB's aanwezig in het ecosysteem (water en land). Als palingen 6000 km migreren, zullen ze hun vetreserves aanspreken en komen er giftige PCB's vrij in het lichaam. Daarnaast kan de embryonale ontwikkeling nadelig beïnvloed worden door ophoping van PCB's in dooiermateriaal.

Decrease in electrical resistivity on depletion of islands of mobility during aging of a bulk metal glass

Science.gov (United States)

Aji, Daisman P. B.; Johari, G. P.

2018-04-01

The effect of structural relaxation on electrical resistivity, ρglass, of strain-free Zr46.75Ti8.25Cu7.5Ni10Be27.5 bulk metallic glass was studied during isothermal aging at several temperatures, Tas. Since cooling of a liquid metal increases its resistivity ρliq, one expects ρglass to increase on aging toward ρliq at T = Ta. Instead, ρglass decreased non-exponentially with the aging time. The activation energy of aging kinetics is 189 kJ mol-1, which is higher than the activation energy of the Johari-Goldstein (JG) relaxation. After considering the sample's contraction, phase separation, and crystallization as possible causes of the decrease in ρglass, we attribute the decrease to depletion of islands of atomic mobility, soft spots, or static heterogeneity. Vibrations of the atoms in these local (loosely packed) regions and in the region's interfacial area contribute to electron scattering. As these deplete on aging, the contribution decreases and ρglass decreases, with a concomitant decrease in macroscopic volume, enthalpy, and entropy (V, H, and S). Local regions of faster mobility also decrease on cooling as V, H, and S of a liquid decrease, but structure fluctuations dominate electron scattering of a liquid metal and ρliq increases effectively according to the Ziman-Nagel theory for a homogenously disordered structure. Whether depletion of such local regions initiates the structural relaxation of a glass, or vice versa, may be resolved by finding a glass that physically ages but shows no JG relaxation.

Gestational 3,3',4,4',5-pentachlorobiphenyl (PCB 126) exposure disrupts fetoplacental unit: Fetal thyroid-cytokines dysfunction.

Science.gov (United States)

Ahmed, R G; El-Gareib, A W; Shaker, H M

2018-01-01

Exposure to polychlorinated biphenyls (PCBs) is related to several endocrine disorders. This study examined the effect of maternal exposure of 3,3',4,4',5-pentachlorobiphenyl (PCB 126) on the fetoplacental unit and fetal thyroid-cytokine axis during the pregnancy. Pregnant albino rats received PCB 126 (20 or 40μg/kgb.wt.) by oral gavage from gestation day (GD) 1 to 20. Potential effects of PCB 126 were evaluated by following the histopathological changes in the placenta by Haematoxylin and Eosin (H&E) stain and measuring the maternofetal thyroid axis (ELIZA), maternofetal body weight, and fetal growth markers (ELIZA), and cytokines (ELIZA) at embryonic day (ED) 20. Placental tissues of both treated groups showed hyperemia, hemorrhage, degeneration and apoptosis in labyrinth layer and spiral artery at GD 20. Both administrations of PCB 126 elevated serum thyrotropin (TSH) concentration, and decreased free thyroxine (FT4) and free triiodothyronine (FT3) concentrations, resulting in a maternofetal hypothyroidism. The presence of hypothyroidism increased fetal serum concentration of transforming growth factor-β (TGF-β), leptin (LEP), tumor necrosis factor-α (TNF-α), interleukin-1β (IL-1β), and decreased the fetal serum insulin growth factor-I (IGF-I), IGF-II, insulin, adiponectin (ADP), and growth hormone (GH) in both treated groups at ED 20. However, the increase in resistin (RETN) and interferon-γ (IFN-γ) was non-significant in low-dose group and highly significant in high-dose group. Simultaneously, the reduction in body weight of the dams and fetuses was observed in both PCB 126 groups of examined day with respect to the control group. The maternal PCB 126 distorted the fetoplacental unit might disrupt the fetal thyroid-cytokines axis and prenatal development. Copyright © 2017 Elsevier Inc. All rights reserved.

Electroremediation of PCB contaminated soil combined with iron nanoparticles: Effect of the soil type

DEFF Research Database (Denmark)

Gomes, Helena I.; Dias-Ferreira, Celia; Ottosen, Lisbeth M.

2015-01-01

Polychlorinated biphenyls (PCB) are carcinogenic and persistent organic pollutants that accumulate in soils and sediments. Currently, there is no cost-effective and sustainable remediation technology for these contaminants. In this work, a new combination of electrodialytic remediation and zero...... nanoparticles. Remediation experiments are made with two different historically PCB contaminated soils, which differ in both soil composition and contamination source. Soil 1 is a mix of soils with spills of transformer oils, while Soil 2 is a superficial soil from a decommissioned school where PCB were used...... as windows sealants. Saponin, a natural surfactant, was also tested to increase the PCB desorption from soils and enhance dechlorination. Remediation of Soil 1 (with highest pH, carbonate content, organic matter and PCB concentrations) obtained the maximum 83% and 60% PCB removal with the two...

On the anelasticity and strain induced structural changes in a Zr-based bulk metallic glass

International Nuclear Information System (INIS)

Caron, A.; Louzguine-Luzguin, D. V.; Kawashima, A.; Inoue, A.; Fecht, H.-J.

2011-01-01

We report on the anelastic behavior of a cyclically loaded Zr 62.5 Fe 5 Cu 22.5 Al 10 bulk metallic glass well below its yield strength. The dynamic mechanical behavior of the glass is discussed on the basis of its structural and thermodynamic properties before and after tests. We show how the kinetically frozen anelastic deformation accumulates at room temperature and causes a structural relaxation and densification of the glass and further leads to its partial crystallization.

Males exceed females in PCB concentrations of cisco (Coregonus artedi) from Lake Superior

Science.gov (United States)

Madenjian, Charles P.; Yule, Daniel L.; Chernyak, Sergei M.; Begnoche, Linda J.; Berglund, Eric K.; Isaac, Edmund J.

2014-01-01

We determined whole-fish polychlorinated biphenyl (PCB) concentrations of 25 male and 25 female age-7 ciscoes (Coregonus artedi) captured from a spawning aggregation in Thunder Bay, Lake Superior, during November 2010. We also determined PCB concentrations in the ovaries and somatic tissue of five additional female ciscoes (ages 5–22). All 55 of these ciscoes were in ripe or nearly ripe condition. Bioenergetics modeling was used to determine the contribution of the growth dilution effect toward a difference in PCB concentrations between the sexes, as females grew substantially faster than males. Results showed that the PCB concentration of males (mean = 141 ng/g) was 43% greater than that of females (mean = 98 ng/g), and this difference was highly significant (P ovaries and the somatic tissue of the five females were 135 and 100 ng/g, respectively. Based on these PCB determinations for the ovaries and somatic tissue, we concluded that release of eggs by females at previous spawnings was not a contributing factor to the observed difference in PCB concentrations between the sexes. Bioenergetics modeling results indicated that the growth dilution effect could explain males being higher than females in PCB concentration by only 3–7%. We concluded that the higher PCB concentration in males was most likely due to higher rate of energy expenditure, originating from greater activity and a higher resting metabolic rate. Mean PCB concentration in the cisco eggs was well below the U. S. Food and Drug Administration and Ontario Ministry of Environment guidelines of 2000 and 844 ng/g, respectively, and this finding may have implications for the cisco roe fishery currently operating in Lake Superior.

PCB management and the environmental movement

International Nuclear Information System (INIS)

White, D.

1995-01-01

Some key issues of public concern about hazardous waste incinerators and, in general, the management of toxic wastes, have been identified with a view to counter arguments brought forward by environmentalists and to offer reassurance based on scientific evidence. The case in point is the long-term management of London's (Ontario) PCB inventory, extensively studied by Proctor and Redfern Ltd., a consultant group. They recommended thermal destruction of the PCBs as the most effective and permanent solution. Their report was subsequently attacked by Greenpeace, whose main concern was the consultants's recommendation to rely on destruction by incineration and removal efficiency values. Greenpeace also raised doubts about recommended measures against emissions of products of incomplete combustion, the incineration of metal containing waste, and the validity of health risk assessment. Evidence from Proctor and Redfern's own consulting experience, and other published scientific studies were used to show the fallacy of Greenpeace's arguments, claiming that they were based on unscientific, outdated and seemingly selective information, resulting in completely misleading assessment of incineration as an effective means of toxic waste management. 7 refs., 2 tabs., 1 fig

Concentration of polychlorinated biphenyl (PCB) congeners in the muscle of Clarias gariepinus and sediment from inland rivers of southwestern Nigeria and estimated potential human health consequences.

Science.gov (United States)

Adeogun, Aina O; Chukwuka, Azubuike V; Okoli, Chukwunonso P; Arukwe, Augustine

2016-01-01

The distributions of polychlorinated biphenyl (PCB) congeners were determined in sediment and muscle of the African sharptooth catfish (Clarias gariepinus) from the Ogun and Ona rivers, southwest Nigeria. In addition, the effect of PCB congeners on condition factor (CF) and associated human health risk was assessed using muscle levels for a noncarcinogenic hazard quotient (HQ) calculation. Elevated concentrations of high-molecular-weight (HMW) PCB congeners were detected in sediment and fish downstream of discharge points of both rivers. A significant reduction in fish body weight and CF was observed to correlate with high PCB congener concentrations in the Ona River. A principal component (PC) biplot revealed significant site-related PCB congener distribution patterns for HMW PCB in samples from the Ogun River (71.3%), while the Ona River (42.6%) showed significant PCB congener patterns for low-molecular-weight (LMW) congeners. Biota-sediment accumulation factor (BSAF) was higher downstream for both rivers, presenting PCB congener-specific accumulation patterns in the Ona River. Significant decreases in fish body weight, length and CF were observed downstream compared to upstream in the Ona River. The non-carcinogenic HQ of dioxin-like congener 189 downstream in both rivers exceeded the HQ = 1 threshold for children and adults for both the Ogun and Ona rivers. Overall, our results suggest that industrial discharges contribute significantly to PCB inputs into these rivers, with potential for significant health implications for neighboring communities that utilize these rivers for fishing and other domestic purposes.

Treatment of transverse patellar fractures: a comparison between metallic and non-metallic implants.

Science.gov (United States)

Heusinkveld, Maarten H G; den Hamer, Anniek; Traa, Willeke A; Oomen, Pim J A; Maffulli, Nicola

2013-01-01

Several methods of transverse patellar fixation have been described. This study compares the clinical outcome and the occurrence of complications of various fixation methods. The databases PubMed, Web of Science, Science Direct, Google Scholar and Google were searched. A direct comparison between fixation techniques using mixed or non-metallic implants and metallic K-wire and tension band fixation shows no significant difference in clinical outcome between both groups. Additionally, studies reporting novel operation techniques show good clinical results. Studies describing the treatment of patients using non-metallic or mixed implants are fewer compared with those using metallic fixation. A large variety of clinical scoring systems were used for assessing the results of treatment, which makes direct comparison difficult. More data of fracture treatment using non-metallic or mixed implants is needed to achieve a more balanced comparison.

Removal of PCB from indoor air and surface materials by introduction of additional sorbing materials

DEFF Research Database (Denmark)

Gunnarsen, Lars Bo; Lyng, Nadja; Kolarik, Barbara

2017-01-01

Alleviation of indoor PCB contamination is extremely expensive because PCB from old primary sources has redistributed to most other surfaces over time. This study investigates the introduction of new removable sorbing materials as a method instantly lowering the concentration of PCB in indoor air...... and slowly decontaminating old surface materials. In three bedrooms of a contaminated apartment respectively new painted gypsum boards, sheets of flexible polyurethane foam and activated carbon fabric were introduced. The PCB concentrations in room air were monitored before the intervention and several times...... during the following 10 months. The PCB concentrations in the old surface materials as well as the new materials were also measured. An immediate reduction of PCB concentration in indoor air, a gradual increase of PCB in new material and as well a gradual reduction in old surface materials were...

Development of planar CT system for multi-layer PCB inspection

Energy Technology Data Exchange (ETDEWEB)

Kim, Seung Ho; Youn, Hanbean; Kam, Soohwa; Park, Eunpyeong; Kim, Ho Kyung [Pusan National University, Busan (Korea, Republic of)

2015-05-15

X-ray defect inspection apparatus can be used in the production line to inspect the PCB. However, a simple X-ray radiography cannot discriminate defects from the multi-layer PCBs because the layers of them overlays the defects. To complement this issue, computed tomography (CT) technology is applied to the NDT system which can offer 3-dimensional information of object. However, CT requires hundreds of projection images to examine a single PCB, hence real-time inspection is nearly impossible. In this study, we develop a planar computed tomography (pCT) system appropriate for the multi-layer PCB inspection. For the image reconstruction of planar cross-section images, we use the digital tomosynthesis (DTS) concept in association with the limited angle scanning. and performance characterization of the pCT system for the PCB inspection. The 3-d Fourier characteristics and more quantitative performance, such as contrast, uniformity, depth resolution will be presented. The cross-sectional images of multi-layer PCBs will also be demonstrated.

A Semi-Analytical Extraction Method for Interface and Bulk Density of States in Metal Oxide Thin-Film Transistors.

Science.gov (United States)

Chen, Weifeng; Wu, Weijing; Zhou, Lei; Xu, Miao; Wang, Lei; Ning, Honglong; Peng, Junbiao

2018-03-11

A semi-analytical extraction method of interface and bulk density of states (DOS) is proposed by using the low-frequency capacitance-voltage characteristics and current-voltage characteristics of indium zinc oxide thin-film transistors (IZO TFTs). In this work, an exponential potential distribution along the depth direction of the active layer is assumed and confirmed by numerical solution of Poisson's equation followed by device simulation. The interface DOS is obtained as a superposition of constant deep states and exponential tail states. Moreover, it is shown that the bulk DOS may be represented by the superposition of exponential deep states and exponential tail states. The extracted values of bulk DOS and interface DOS are further verified by comparing the measured transfer and output characteristics of IZO TFTs with the simulation results by a 2D device simulator ATLAS (Silvaco). As a result, the proposed extraction method may be useful for diagnosing and characterising metal oxide TFTs since it is fast to extract interface and bulk density of states (DOS) simultaneously.

A Semi-Analytical Extraction Method for Interface and Bulk Density of States in Metal Oxide Thin-Film Transistors

Directory of Open Access Journals (Sweden)

Weifeng Chen

2018-03-01

Full Text Available A semi-analytical extraction method of interface and bulk density of states (DOS is proposed by using the low-frequency capacitance–voltage characteristics and current–voltage characteristics of indium zinc oxide thin-film transistors (IZO TFTs. In this work, an exponential potential distribution along the depth direction of the active layer is assumed and confirmed by numerical solution of Poisson’s equation followed by device simulation. The interface DOS is obtained as a superposition of constant deep states and exponential tail states. Moreover, it is shown that the bulk DOS may be represented by the superposition of exponential deep states and exponential tail states. The extracted values of bulk DOS and interface DOS are further verified by comparing the measured transfer and output characteristics of IZO TFTs with the simulation results by a 2D device simulator ATLAS (Silvaco. As a result, the proposed extraction method may be useful for diagnosing and characterising metal oxide TFTs since it is fast to extract interface and bulk density of states (DOS simultaneously.

Development of Efficient and Stable Inverted Bulk Heterojunction (BHJ) Solar Cells Using Different Metal Oxide Interfaces

OpenAIRE

Ivan Litzov; Christoph J. Brabec

2013-01-01

Solution-processed inverted bulk heterojunction (BHJ) solar cells have gained much more attention during the last decade, because of their significantly better environmental stability compared to the normal architecture BHJ solar cells. Transparent metal oxides (MeO x ) play an important role as the dominant class for solution-processed interface materials in this development, due to their excellent optical transparency, their relatively high electrical conductivity and their tunable work fun...

An improved inventory of polychlorinated biphenyls in China: A case study on PCB-153

Science.gov (United States)

Xu, Yue; Tian, Chongguo; Wang, Xiaoping; Ma, Jianmin; Tang, Jianhui; Chen, Yingjun; Li, Jun; Zhang, Gan

2018-06-01

Emission inventory of pollutants is essential for the environmental fate study and management of the pollutant. To construct a reasonable PCB (polychlorinated biphenyls) inventory in China, this study estimates PCB usage and emission using power generating capacity, installed capacity of power plants and transformer substations, population density and GDP as surrogates. Inventory of representative PCB (PCB-153) with a resolution of 1/4° latitude × 1/4° longitude in China from 1952 to 2005 was generated and assessed as an example. Totally, about 20.3 kt PCBs were applied in China, of which 179 t were PCB-153. By the end of 2005, most of them (56.4%) were emitted into the soil, 2.7% entered the air, and about 20.8% was sealed in storage site or still in service. Historical emissions exhibited increasing trends after 1968, 1984 and 1994, which were mainly associated with usage or disposal processes. Although primary emission has been declined since 2005, the influence of secondary emission from soils, unintentionally produced PCBs (UP-PCB), and reemission from storage sites could be a long-lasting issue in the future. This new emission inventory improves previous PCB emission inventory significantly, which underestimated PCB emission in China considerably.

Dynamics of PCB removal and detoxification in historically contaminated soils amended with activated carbon

Energy Technology Data Exchange (ETDEWEB)

Vasilyeva, Galina K., E-mail: gkvasilyeva@issp.psn.r [Institute of Physicochemical and Biological Problems in Soil Science, Russian Academy of Sciences, Pushchino 142290 (Russian Federation); Strijakova, Elena R. [Institute of Physicochemical and Biological Problems in Soil Science, Russian Academy of Sciences, Pushchino 142290 (Russian Federation); Nikolaeva, Svetlana N.; Lebedev, Albert T. [Chemistry Department of Moscow State University, Moscow (Russian Federation); Shea, Patrick J. [School of Natural Resources, University of Nebraska-Lincoln (United States); Department of Environmental, Agricultural and Occupational Health, University of Nebraska Medical Center, Lincoln, NE 68583-0817 (United States)

2010-03-15

Activated carbon (AC) can help overcome toxicity of pollutants to microbes and facilitate soil bioremediation. We used this approach to treat a Histosol and an Alluvial soil historically contaminated with PCB (4190 and 1585 mg kg{sup -1}, respectively; primarily tri-, tetra- and pentachlorinated congeners). Results confirmed PCB persistence; reductions in PCB extractable from control and AC-amended soils were mostly due to a decrease in tri- and to some extent tetrachlorinated congeners as well as formation of a bound fraction. Mechanisms of PCB binding by soil and AC were different. In addition to microbial degradation of less chlorinated congeners, we postulate AC catalyzed dechlorination of higher chlorinated congeners. A large decrease in bioavailable PCB in AC-amended soils was demonstrated by greater clover germination and biomass. Phytotoxicity was low in treated soils but remained high in untreated soils for the duration of a 39-month experiment. These observations indicate the utility of AC for remediation of soils historically contaminated with PCB. - Activated carbon promotes remediation of soils historically contaminated with PCB.

Dynamics of PCB removal and detoxification in historically contaminated soils amended with activated carbon

International Nuclear Information System (INIS)

Vasilyeva, Galina K.; Strijakova, Elena R.; Nikolaeva, Svetlana N.; Lebedev, Albert T.; Shea, Patrick J.

2010-01-01

Activated carbon (AC) can help overcome toxicity of pollutants to microbes and facilitate soil bioremediation. We used this approach to treat a Histosol and an Alluvial soil historically contaminated with PCB (4190 and 1585 mg kg -1 , respectively; primarily tri-, tetra- and pentachlorinated congeners). Results confirmed PCB persistence; reductions in PCB extractable from control and AC-amended soils were mostly due to a decrease in tri- and to some extent tetrachlorinated congeners as well as formation of a bound fraction. Mechanisms of PCB binding by soil and AC were different. In addition to microbial degradation of less chlorinated congeners, we postulate AC catalyzed dechlorination of higher chlorinated congeners. A large decrease in bioavailable PCB in AC-amended soils was demonstrated by greater clover germination and biomass. Phytotoxicity was low in treated soils but remained high in untreated soils for the duration of a 39-month experiment. These observations indicate the utility of AC for remediation of soils historically contaminated with PCB. - Activated carbon promotes remediation of soils historically contaminated with PCB.

Effects of maternal exposure to estrogen and PCB on different life stages of Zebrafish (Danio rerio)

Energy Technology Data Exchange (ETDEWEB)

Olsson, Per-Erik; Westerlund, L; Billsson, K; Berg, A H [Umeaa Univ. (Sweden). Dept. of Cellular and Developmental Biology; Teh, S J; Hinton, D E [California Univ., Davis, CA (United States). Dept. of Anatomy, Physiology and Cell Biology; Tysklind, M [Umeaa Univ., (Sweden). Dept. of Environmental Chemistry; Nilsson, Jan; Eriksson, Lars-Ove [Swedish Univ. of Agricultural Sciences, Umeaa (Sweden). Dept. of Aquaculture

1999-02-01

PCBs have been found to impair both reproduction and development in fish. We have investigated the effects of 3 PCB congeners, 2,3,3`,4,4`,5,6-HpCB (PCB-190); 2,3,4,4`-TeCB (PCB-60); and 2,2`,4,6,6`-PeCB (PCB-104), and the estrogenic hormone 17{beta}-estradiol on fecundity, early life-stage mortality, gross morphology and histology of zebrafish (Danio rerio). While none of the studied substances reduced fecundity, they increased embryo and larval mortality. The most severe effects on viability were observed following treatment with 17{beta}-estradiol or the weakly estrogenic PCB-104. Following 17{beta}-estradiol or PCB-104 exposure, mortality continued through the yolksac absorption phase. PCB-60, on the other hand, resulted in mortality between the 30% epiboly stage and 75% epiboly stage. At the same time as embryos started to die, embryo development and hatching were delayed. PCB-190 showed only moderate effects on early-life stage mortality. The fish were reared until sexual maturation where after they were subjected to gross morphological and histological analyses. Changes in morphology were observed following PCB-104 and PCB-190 treatment. Both substances gave rise to craniofacial malformations while PCB-104 also led to lordosis in females and scoliosis in fish of both sexes. From histological analysis it was found that PCB-104 and 17{beta}-estradiol resulted in karyorrhexis and karyolysis in the kidney. Possible signs of bile stasis were observed following 17{beta}-estradiol and PCB-190 treatment. Some effects were observed on the gonads, including areas in the ovary showing atresia and limited failure of testicular spermatogenesis in 17{beta}-estradiol, PCB-104, and PCB-60 treated fish. While all studied substances resulted in effects on offspring, the observation that estrogenic substances are highly embryotoxic, raises concern that endocrine disrupting substances may severely reduce fish populations in polluted areas

Plant exudates promote PCB degradation by a rhodococcal rhizobacteria

Energy Technology Data Exchange (ETDEWEB)

Toussaint, Jean-Patrick; Pham, Thi Thanh My; Barriault, Diane; Sylvestre, Michel [Instiut National de la Recherche Scientifique INRS, Laval, QC (Canada). Inst. Armand-Frappier

2012-09-15

Rhodococcus erythropolis U23A is a polychlorinated biphenyl (PCB)-degrading bacterium isolated from the rhizosphere of plants grown on a PCB-contaminated soil. Strain U23A bphA exhibited 99% identity with bphA1 of Rhodococcus globerulus P6. We grew Arabidopsis thaliana in a hydroponic axenic system, collected, and concentrated the plant secondary metabolite-containing root exudates. Strain U23A exhibited a chemotactic response toward these root exudates. In a root colonizing assay, the number of cells of strain U23A associated to the plant roots (5.7 x 105 CFU g{sup -1}) was greater than the number remaining in the surrounding sand (4.5 x 104 CFU g{sup -1}). Furthermore, the exudates could support the growth of strain U23A. In a resting cell suspension assay, cells grown in a minimal medium containing Arabidopsis root exudates as sole growth substrate were able to metabolize 2,3,4'- and 2,3',4-trichlorobiphenyl. However, no significant degradation of any of congeners was observed for control cells grown on Luria-Bertani medium. Although strain U23A was unable to grow on any of the flavonoids identified in root exudates, biphenyl-induced cells metabolized flavanone, one of the major root exudate components. In addition, when used as co-substrate with sodium acetate, flavanone was as efficient as biphenyl to induce the biphenyl catabolic pathway of strain U23A. Together, these data provide supporting evidence that some rhodococci can live in soil in close association with plant roots and that root exudates can support their growth and trigger their PCB-degrading ability. This suggests that, like the flagellated Gram-negative bacteria, non-flagellated rhodococci may also play a key role in the degradation of persistent pollutants. (orig.)

Determination of the human cytochrome P450 monooxygenase catalyzing the enantioselective oxidation of 2,2',3,5',6-pentachlorobiphenyl (PCB 95) and 2,2',3,4,4',5',6-heptachlorobiphenyl (PCB 183).

Science.gov (United States)

Nagayoshi, Haruna; Kakimoto, Kensaku; Konishi, Yoshimasa; Kajimura, Keiji; Nakano, Takeshi

2017-10-17

2,2',3,5',6-Pentachlorobiphenyl (PCB 95) and 2,2',3,4,4',5',6-heptachlorobiphenyl (PCB 183) possess axial chirality and form the aS and aR enantiomers. The enantiomers of these congeners have been reported to accumulate in the human body enantioselectively via unknown mechanisms. In this study, we determined the cytochrome P450 (CYP) monooxygenase responsible for the enantioselective oxidization of PCB 95 and PCB 183, using a recombinant human CYP monooxygenase. We evaluated 13 CYP monooxygenases, namely CYP1A1, CYP1A2, CYP1B1, CYP2A6, CYP2B6, CYP2C8, CYP2C19, CYP2E1, CYP2J2, CYP3A4, CYP3A5, CYP4F2, and aromatase (CYP19), and revealed that CYP2A6 preferably oxidizes aS-PCB 95 enantioselectively; however, it did not oxidize PCB 183. The enantiomer composition was elevated from 0.5 (racemate) to 0.54. In addition, following incubation with CYP2A6, the enantiomer fraction (EF) of PCB 95 demonstrated a time-dependent increase.

Magnetic properties and microstructural homogeneity in NdFeAl bulk metallic glasses

International Nuclear Information System (INIS)

Ortega-Zempoalteca, R.; Valenzuela, R.; Betancourt, I.

2011-01-01

Bulk metallic glasses of nominal composition Nd 60 Fe 30 Al 10 were prepared by copper mold casting in the form of rods of 3 mm in diameter and 50 mm in length. Preparation conditions were varied to assess the effects of the injection distance and the injection pressure of the melt. In order to determine their microstructure, disk-shaped samples were obtained from different cut zones along the axis rod. A non-homogeneous phase distribution was observed, which resulted from the heat transfer regime during the cooling of the melt in the copper mold. As expected, the nature, distribution and volumetric fraction of the various phases produced play an important role on the resulting magnetic properties. Among the main observed phases are Fe-rich rod-like crystals, Nd-rich dendritic crystals and a ''like-amorphous'' matrix. The hard magnetic properties of these materials can be associated with this matrix. In these cooling regimes, the coercive field increases as the cooling rate of the amorphous matrix increases. Hysteresis loops showed a high degree of coupling between phases with different magnetic order. Both the coercive field and the magnetization showed a significant variation along the rod axis; a maximum appeared as a function of the axis length. In order to gather more information about the coupling between the observed phases, δM (or Henkel) plots were obtained, showing an exchange character for interactions (copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Males exceed females in PCB concentrations of cisco (Coregonus artedi) from Lake Superior.

Science.gov (United States)

Madenjian, Charles P; Yule, Daniel L; Chernyak, Sergei M; Begnoche, Linda J; Berglund, Eric K; Isaac, Edmund J

2014-09-15

We determined whole-fish polychlorinated biphenyl (PCB) concentrations of 25 male and 25 female age-7 ciscoes (Coregonus artedi) captured from a spawning aggregation in Thunder Bay, Lake Superior, during November 2010. We also determined PCB concentrations in the ovaries and somatic tissue of five additional female ciscoes (ages 5-22). All 55 of these ciscoes were in ripe or nearly ripe condition. Bioenergetics modeling was used to determine the contribution of the growth dilution effect toward a difference in PCB concentrations between the sexes, as females grew substantially faster than males. Results showed that the PCB concentration of males (mean = 141 ng/g) was 43% greater than that of females (mean = 98 ng/g), and this difference was highly significant (PPCB concentrations in the ovaries and the somatic tissue of the five females were 135 and 100 ng/g, respectively. Based on these PCB determinations for the ovaries and somatic tissue, we concluded that release of eggs by females at previous spawnings was not a contributing factor to the observed difference in PCB concentrations between the sexes. Bioenergetics modeling results indicated that the growth dilution effect could explain males being higher than females in PCB concentration by only 3-7%. We concluded that the higher PCB concentration in males was most likely due to higher rate of energy expenditure, originating from greater activity and a higher resting metabolic rate. Mean PCB concentration in the cisco eggs was well below the U. S. Food and Drug Administration and Ontario Ministry of Environment guidelines of 2000 and 844 ng/g, respectively, and this finding may have implications for the cisco roe fishery currently operating in Lake Superior. Published by Elsevier B.V.

40 CFR 761.316 - Interpreting PCB concentration measurements resulting from this sampling scheme.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Interpreting PCB concentration... § 761.79(b)(3) § 761.316 Interpreting PCB concentration measurements resulting from this sampling... composite is 20 µg/100 cm2, then the entire 9.5 square meters has a PCB surface concentration of 20 µg/100...

Correlations between elastic moduli and properties in bulk metallic glasses

International Nuclear Information System (INIS)

Wang Weihua

2006-01-01

A survey of the elastic, mechanical, fragility, and thermodynamic properties of bulk metallic glasses (BMGs) and glass-forming liquids is presented. It is found that the elastic moduli of BMGs have correlations with the glass transition temperature, melting temperature, mechanical properties, and even liquid fragility. On the other hand, the elastic constants of available BMGs show a rough correlation with a weighted average of the elastic constants for the constituent elements. Although the theoretical and physical reasons for the correlations are to be clarified, these correlations could assist in understanding the long-standing issues of glass formation and the nature of glass and simulate the work of theorists. Based on the correlation, we show that the elastic moduli can assist in selecting alloying components for controlling the elastic properties and glass-forming ability of the BMGs and thus can guide BMG design. As case study, we report the formation of the families of rare-earth-based BMGs with controllable properties

PCB in the environment: bio-based processes for soil decontamination and management of waste from the industrial production of Pleurotus ostreatus.

Science.gov (United States)

Siracusa, Giovanna; Becarelli, Simone; Lorenzi, Roberto; Gentini, Alessandro; Di Gregorio, Simona

2017-10-25

Polychlorinated biphenyls (PCBs) are hazardous soil contaminants for which a bio-based technology for their recovery is essential. The objective of this study was to validate the exploitation of spent mushroom substrate (SMS), a low or null cost organic waste derived from the industrial production of P. ostreatus, as bulking agent in a dynamic biopile pilot plant. The SMS shows potential oxidative capacity towards recalcitrant compounds. The aim was consistent with the design of a process of oxidation of highly chlorinated PCBs, which is independent from their reductive dehalogenation. Feasibility was verified at a mesocosm scale and validated at pilot scale in a dynamic biopile pilot plant treating ten tons of a historically contaminated soil (9.28±0.08mg PCB/kg soil dry weight). Mixing of the SMS with the soil was required for the depletion of the contaminants. At the pilot scale, after eight months of incubation, 94.1% depletion was recorded. A positive correlation between Actinobacteria and Firmicutes active metabolism, soil laccase activity and PCB removal was observed. The SMS was found to be exploitable as a versatile low cost organic substrate capable of activating processes for the oxidation of highly chlorinated PCBs. Moreover, its exploitation as bulking agent in biopiles is a valuable management strategy for the re-utilisation of an organic waste deriving from the industrial cultivation of edible mushrooms. Copyright © 2017 Elsevier B.V. All rights reserved.

Inside-sediment partitioning of PAH, PCB and organochlorine compounds and inferences on sampling and normalization methods

International Nuclear Information System (INIS)

Opel, Oliver; Palm, Wolf-Ulrich; Steffen, Dieter; Ruck, Wolfgang K.L.

2011-01-01

Comparability of sediment analyses for semivolatile organic substances is still low. Neither screening of the sediments nor organic-carbon based normalization is sufficient to obtain comparable results. We are showing the interdependency of grain-size effects with inside-sediment organic-matter distribution for PAH, PCB and organochlorine compounds. Surface sediment samples collected by Van-Veen grab were sieved and analyzed for 16 PAH, 6 PCB and 18 organochlorine pesticides (OCP) as well as organic-matter content. Since bulk concentrations are influenced by grain-size effects themselves, we used a novel normalization method based on the sum of concentrations in the separate grain-size fractions of the sediments. By calculating relative normalized concentrations, it was possible to clearly show underlying mechanisms throughout a heterogeneous set of samples. Furthermore, we were able to show that, for comparability, screening at <125 μm is best suited and can be further improved by additional organic-carbon normalization. - Research highlights: → New method for the comparison of heterogeneous sets of sediment samples. → Assessment of organic pollutants partitioning mechanisms in sediments. → Proposed method for more comparable sediment sampling. - Inside-sediment partitioning mechanisms are shown using a new mathematical approach and discussed in terms of sediment sampling and normalization.

Environment Canada defends decision to ban PCB waste exports

International Nuclear Information System (INIS)

Anon.

1995-01-01

The position of Environment Canada in banning the export of PCB waste to the United States was defended as falling within their jurisdiction under provisions of the the Canadian Environmental Protection Act. The United States had previously banned the import of Canadian PCBs, but when it reversed its decision Environment Canada posted an Interim Order, upholding the ban. The decision to do so was based on protection of the large investment that was made to develop the Canadian PCB incineration facility in Swan Lake, Alberta. Canada also had an obligation under the Basel Convention to reduce it cross boundary movement of hazardous waste and provide adequate destruction facilities in Canada. Legal implications of PCB exports and the uncertainty of continuing access to American facilities were also cited as reasons for issuing the Interim Order

Toxicological Profile of Ultrapure 2,2′,3,4,4′,5,5′-Heptachlorbiphenyl (PCB 180) in Adult Rats

Science.gov (United States)

Viluksela, Matti; Heikkinen, Päivi; van der Ven, Leo T. M.; Rendel, Filip; Roos, Robert; Esteban, Javier; Korkalainen, Merja; Lensu, Sanna; Miettinen, Hanna M.; Savolainen, Kari; Sankari, Satu; Lilienthal, Hellmuth; Adamsson, Annika; Toppari, Jorma; Herlin, Maria; Finnilä, Mikko; Tuukkanen, Juha; Leslie, Heather A.; Hamers, Timo; Hamscher, Gerd; Al-Anati, Lauy; Stenius, Ulla; Dervola, Kine-Susann; Bogen, Inger-Lise; Fonnum, Frode; Andersson, Patrik L.; Schrenk, Dieter; Halldin, Krister; Håkansson, Helen

2014-01-01

PCB 180 is a persistent non-dioxin-like polychlorinated biphenyl (NDL-PCB) abundantly present in food and the environment. Risk characterization of NDL-PCBs is confounded by the presence of highly potent dioxin-like impurities. We used ultrapure PCB 180 to characterize its toxicity profile in a 28-day repeat dose toxicity study in young adult rats extended to cover endocrine and behavioral effects. Using a loading dose/maintenance dose regimen, groups of 5 males and 5 females were given total doses of 0, 3, 10, 30, 100, 300, 1000 or 1700 mg PCB 180/kg body weight by gavage. Dose-responses were analyzed using benchmark dose modeling based on dose and adipose tissue PCB concentrations. Body weight gain was retarded at 1700 mg/kg during loading dosing, but recovered thereafter. The most sensitive endpoint of toxicity that was used for risk characterization was altered open field behavior in females; i.e. increased activity and distance moved in the inner zone of an open field suggesting altered emotional responses to unfamiliar environment and impaired behavioral inhibition. Other dose-dependent changes included decreased serum thyroid hormones with associated histopathological changes, altered tissue retinoid levels, decreased hematocrit and hemoglobin, decreased follicle stimulating hormone and luteinizing hormone levels in males and increased expression of DNA damage markers in liver of females. Dose-dependent hypertrophy of zona fasciculata cells was observed in adrenals suggesting activation of cortex. There were gender differences in sensitivity and toxicity profiles were partly different in males and females. PCB 180 adipose tissue concentrations were clearly above the general human population levels, but close to the levels in highly exposed populations. The results demonstrate a distinct toxicological profile of PCB 180 with lack of dioxin-like properties required for assignment of WHO toxic equivalency factor. However, PCB 180 shares several toxicological

Stability of bulk metallic glass structure

Energy Technology Data Exchange (ETDEWEB)

Jain, H.; Williams, D.B.

2003-06-18

The fundamental origins of the stability of the (Pd-Ni){sub 80}P{sub 20} bulk metallic glasses (BMGs), a prototype for a whole class of BMG formers, were explored. While much of the properties of their BMGs have been characterized, their glass-stability have not been explained in terms of the atomic and electronic structure. The local structure around all three constituent atoms was obtained, in a complementary way, using extended X-ray absorption fine structure (EXAFS), to probe the nearest neighbor environment of the metals, and extended energy loss fine structure (EXELFS), to investigate the environment around P. The occupied electronic structure was investigated using X-ray photoelectron spectroscopy (XPS). The (Pd-Ni){sub 80}P{sub 20} BMGs receive their stability from cumulative, and interrelated, effects of both atomic and electronic origin. The stability of the (Pd-Ni){sub 80}P{sub 20} BMGs can be explained in terms of the stability of Pd{sub 60}Ni{sub 20}P{sub 20} and Pd{sub 30}Ni{sub 50}P{sub 20}, glasses at the end of BMG formation. The atomic structure in these alloys is very similar to those of the binary phosphide crystals near x=0 and x=80, which are trigonal prisms of Pd or Ni atoms surrounding P atoms. Such structures are known to exist in dense, randomly-packed systems. The structure of the best glass former in this series, Pd{sub 40}Ni{sub 40}P{sub 20} is further described by a weighted average of those of Pd{sub 30}Ni{sub 50}P{sub 20} and Pd{sub 60}Ni{sub 20}P{sub 20}. Bonding states present only in the ternary alloys were found and point to a further stabilization of the system through a negative heat of mixing between Pd and Ni atoms. The Nagel and Tauc criterion, correlating a decrease in the density of states at the Fermi level with an increase in the glass stability, was consistent with greater stability of the Pd{sub x}Ni{sub (80-x)}P{sub 20} glasses with respect to the binary alloys of P. A valence electron concentration of 1.8 e/a, which

Stereoselective bioaccumulation of chiral PCB 91 in earthworm and its metabolomic and lipidomic responses.

Science.gov (United States)

He, Zeying; Wang, Yuehua; Zhang, Yanwei; Cheng, Haiyan; Liu, Xiaowei

2018-07-01

Stereoselective bioaccumulation, elimination, metabolomic and lipidomic responses of earthworm Eisenia fetida exposed to chiral polychlorinated biphenyl (PCB) 91 in an earthworm-soil system were investigated. Preferential bioaccumulation of (-)-PCB 91 and elimination of (+)-PCB 91 were observed following 50 and 500 μg/kg dwt exposures. Enantiomer fraction (EF) values decreased over time during the uptake and elimination periods. Metabolomics and lipidomics techniques based on ultra-performance liquid chromatography/quadrupole time-of-flight mass spectrometry (UPLC-QTOF-MS) revealed significant changes in 108 metabolites after earthworms exposure to (+)-, (-)-, and (±)-PCB 91, compared to control groups. Forty two of these metabolites were identified as amino acids, nucleosides, fatty acids, dicarboxylic acids, vitamins or others. Lysophospholipids including six lysophosphatidylcholines (LPC), six lysophosphatidylethanolamine (LPE), eight lysophosphatidylinositol (LPI) and five lysophosphatidylserine (LPS) were also differentially expressed between exposure and control groups. Alterations in the levels of metabolites and lipids indicated stereoselective effects of chiral PCB 91 on earthworm amino acid, energy, and nucleotide metabolism, neurodevelopment and gene expression. Overall, the effects of (+)-PCB 91 were more pronounced than that of (-)- and (±)-PCB 91. Copyright © 2018 Elsevier Ltd. All rights reserved.

Effects of PCB contamination on the reproduction of the DAB Limanda limanda L. under laboratory conditions

Science.gov (United States)

Fonds, Mark; Casal, Elizabeth; Schweizer, Dominik; Boon, Jan P.; Van der Veer, Henk W.

The effect of PCB contamination on the reproduction of female dab was studied under laboratory conditions. Females were contaminated during gonad maturation by multiple oral administration of capsules containing the technical PCB mixture Clophen A40. PCB contamination resulted in increased levels in the eggs, with concentrations of selected PCB congeners of 35 to 86 μg·g -1 lipid for PCB-exposed fish, 10 μg·g -1 lipid for eggs from fish fed with mussel meat and fish fed with shrimp. A statistically significant dose-effect relationship was found between the PCB content of the eggs and the PCB dose ingested by the fish. For eggs from the PCB-treated fish the mean fertilization rate was 61% and mean hatching 45%, compared to 67% fertilization and 59% hatching for eggs from untreated fish. Rate of development and survival of the eggs and mortality of the larvae after hatching were mainly related to incubation temperature. No statistically significant differences between untreated and PCB-treated fish could be found in egg production, egg quality, fertilization rate, hatching rate and survival of larvae.

Characterization of LC sensor structures realized by PCB and LTCC technology for determining moisture in building materials

Directory of Open Access Journals (Sweden)

Milan R. Radovanović

2018-03-01

Full Text Available This paper compares performances of two wireless sensors for measuring water concentration in building materials, one manufactured by the printed circuit board (PCB technology and another one using the low temperature co-fired ceramics (LTCC process. The fabricated sensors consist of inductive part (L and interdigitated capacitive part (C in one metal layer, connected in parallel. Inductance of inductive part was kept constant, whereas capacitance of capacitive part was changed by exposing the sensor to different moisture concentration, changing its resonant frequency. The variation of resonant frequency as a function of different water concentration was measured, using antenna coil and impedance analyser, in two widely used construction materials: clay brick and autoclaved aerated concrete block. Surface analysis for two sensors was performed by means of 3D profilometer. Mechanical properties of the sensors were measured for both conductive segments (copper and silver and substrates materials (PCB and ceramics substrates using nanoindenter. Comparative characteristics of the sensors are presented from their application point of view.

Automatic extraction of via in the CT image of PCB

Science.gov (United States)

Liu, Xifeng; Hu, Yuwei

2018-04-01

In modern industry, the nondestructive testing of printed circuit board (PCB) can prevent effectively the system failure and is becoming more and more important. In order to detect the via in the PCB base on the CT image automatically accurately and reliably, a novel algorithm for via extraction based on weighting stack combining the morphologic character of via is designed. Every slice data in the vertical direction of the PCB is superimposed to enhanced vias target. The OTSU algorithm is used to segment the slice image. OTSU algorithm of thresholding gray level images is efficient for separating an image into two classes where two types of fairly distinct classes exist in the image. Randomized Hough Transform was used to locate the region of via in the segmented binary image. Then the 3D reconstruction of via based on sequence slice images was done by volume rendering. The accuracy of via positioning and detecting from a CT images of PCB was demonstrated by proposed algorithm. It was found that the method is good in veracity and stability for detecting of via in three dimensional.

Microbial ecology of bacterially mediated PCB biodegradation

International Nuclear Information System (INIS)

Pettigrew, C.A. Jr.

1989-01-01

The roles of plasmid mediated and consortia mediated polychlorinated biphenyl (PCB) biodegradation by bacterial populations isolated from PCB contaminated freshwater sediments were investigated. PCB degrading bacteria were isolated by DNA:DNA colony hybridization, batch enrichments, and chemostat enrichment. Analysis of substrate removal and metabolite production were done using chlorinated biphenyl spray plates, reverse phase high pressure liquid chromatography, Cl - detection, and 14 C-labeled substrate mineralization methods. A bacterial consortium, designated LPS10, involved in a concerted metabolic attack on chlorinated biphenyls, was shown to mineralize 4-chlorobiphenyl (4CB) and 4,4'-dichlorobiphenyl (4,4' CB). The LPS10 consortium was isolated by both batch and chemostat enrichment using 4CB and biphenyl (BP) as sole carbon source and was found to have tree bacterial isolates that predominated; these included: Pseudomonas, testosteroni LPS10A which mediated the breakdown of 4CB and 4,4' CB to the putative meta-cleavage product and subsequently to 4-chlorobenzoic acid (4CBA), an isolate tentatively identified as an Arthrobacter sp. LPS10B which mediated 4CBA degradation, and Pseudomonas putida by A LPS10C whose role in the consortium has not been determined

Characterising boiler ash from a circulating fluidised bed municipal solid waste incinerator and distribution of PCDD/F and PCB.

Science.gov (United States)

Zhang, Mengmei; Buekens, Alfons; Li, Xiaodong

2018-05-31

In this study, ash samples were collected from five locations situated in the boiler of a circulating fluidised bed municipal solid waste incinerator (high- and low-temperature superheater, evaporator tubes and upper and lower economiser). These samples represent a huge range of flue gas temperatures and were characterised for their particle size distribution, surface characteristics, elemental composition, chemical forms of carbon and chlorine and distribution of polychlorinated dibenzo-p-dioxins (PCDD), dibenzofurans (PCDF) and biphenyls (PCB). Enrichment of chlorine, one of the main elements of organochlorinated pollutants, and copper, zinc and lead, major catalytic metals for dioxin-like compounds, was observed in lower-temperature ash deposits. The speciation of carbon and chlorine on ash surfaces was established, showing a positive correlation between organic chlorine and oxygen-containing carbon functional groups. The load of PCDD/F and PCB (especially dioxin-like PCB) tends to rise rapidly with falling temperature of flue gas, reaching their highest value in economiser ashes. The formation of PCDD/F congeners through the chlorophenol precursor route apparently was enhanced downstream the boiler. Principal component analysis (PCA) was applied to study the links between the ash characteristics and distribution of chloro-aromatics. The primary purpose of this study is improving the understanding of any links between the characteristics of ash from waste heat systems and its potential to form PCDD/F and PCB. The question is raised whether further characterisation of fly ash may assist to establish a diagnosis of poor plant operation, inclusive the generation, destruction and eventual emission of persistent organic pollutants (POPs).

Remediation of PCB-contaminated soils. Risk analysis of biological in situ processes

Energy Technology Data Exchange (ETDEWEB)

Rein, Arno

2006-12-08

plants might be a promising approach. Degradation kinetics in soil was estimated, but it is associated with a high uncertainty. The relation of degradation kinetics in laboratory (solution) to field conditions (soil) necessitates further research. Results of exemplary modelling were sensitive to estimated removal velocities, and especially to variable bacterial numbers in soil. A multimedia model was set up to estimate biodegradation and metabolite formation, fate and transport of contaminants and risks arising from the exposure to contaminated media. With this model, deterministic and probabilistic calculations (performing Monte Carlo simulations) were carried out to generically evaluate rhizoremediation of PCB contaminated soil. Results indicate a clear potential for risk reduction associated to the use of F113L::1180 and willow plants. PCB was effectively reduced by the investigated strains but nonetheless, chlorobenzoic acids (CBAs) as degradation products of concern revealed a high importance for the aquatic pathway (leaching, groundwater transport, mixing with surface water) and the uptake into plants. Thus, drinking water wells should be located in a sufficient distance to the source (5 km at least as a conservative estimate for the studied scenario). However, high uncertainty remains for the degradation potential of PCB mixtures in soils. Risks associated to the investigated GMOs are expected to be very low. Results of laboratory experiments with F113 derivatives and field release tests with non-GM F113 strains gave no significant hint on uncontrolled bacterial spreading. Observed gene transfer rates were very low, as the introduced bph trait is stably inserted into the chromosome of F113. Potential impacts of GMOs on microbial soil communities also were very low, but there was a shift in rhizosphere populations. Uncertainty is given for possible long-term effects, especially for gene transfer processes and impacts on soil bacteria, and for potential adverse

Analysis of Pressure-Volume Relationship for Bulk Metallic Glasses

Directory of Open Access Journals (Sweden)

H. K. Rai

2008-01-01

Full Text Available Relationship between compression (V/V0 and pressure have been studied for five bulk metallic glasses (BMGs viz. Zr41Ti14Cu12.5Ni10Be22.5, Zr41Ti14Cu12.5Ni9Be22.5C1, Zr48Nb8Cu12Fe8Be24, (Zr0.59Ti0.06Cu0.22Ni0.1385.7Al14.3 and SiO2.TiO2 in the compression ranges of V/V0 =1.00 to V/V0 = 0.10. Six forms of equation of state reported in the literature have been used in the present study to calculate pressure corresponding to different values of compressions. The comparison of graph plotted between the logarithms of calculated value of pressure to logarithm of calculated value of compression (V/V0 reveals that the agreement of Brennan-Stacey equation of state (EOS and Poirier-Tarantolla equation of state are not good. It has been found that the assumptions, on which these equations are based, do not satisfy well in case of given BMGs.

Intestinal exposure to PCB 153 induces inflammation via the ATM/NEMO pathway.

Science.gov (United States)

Phillips, Matthew C; Dheer, Rishu; Santaolalla, Rebeca; Davies, Julie M; Burgueño, Juan; Lang, Jessica K; Toborek, Michal; Abreu, Maria T

2018-01-15

Polychlorinated biphenyls (PCBs) are persistent organic pollutants that adversely affect human health. PCBs bio-accumulate in organisms important for human consumption. PCBs accumulation in the body leads to activation of the transcription factor NF-κB, a major driver of inflammation. Despite dietary exposure being one of the main routes of exposure to PCBs, the gut has been widely ignored when studying the effects of PCBs. We investigated the effects of PCB 153 on the intestine and addressed whether PCB 153 affected intestinal permeability or inflammation and the mechanism by which this occurred. Mice were orally exposed to PCB 153 and gut permeability was assessed. Intestinal epithelial cells (IECs) were collected and evaluated for evidence of genotoxicity and inflammation. A human IEC line (SW480) was used to examine the direct effects of PCB 153 on epithelial function. NF-кB activation was measured using a reporter assay, DNA damage was assessed, and cytokine expression was ascertained with real-time PCR. Mice orally exposed to PCB 153 had an increase in intestinal permeability and inflammatory cytokine expression in their IECs; inhibition of NF-кB ameliorated both these effects. This inflammation was associated with genotoxic damage and NF-кB activation. Exposure of SW480 cells to PCB 153 led to similar effects as seen in vivo. We found that activation of the ATM/NEMO pathway by genotoxic stress was upstream of NF-kB activation. These results demonstrate that oral exposure to PCB 153 is genotoxic to IECs and induces downstream inflammation and barrier dysfunction in the intestinal epithelium. Copyright © 2017 Elsevier Inc. All rights reserved.

Dioxin, furan and PCB serum levels in a South African Tswana population: comparing the polluting effects of using different cooking and heating fuels.

Science.gov (United States)

Pieters, Rialet; Focant, Jean-François

2014-05-01

In South Africa, 26-50% of households use solid fuel for cooking food and heating houses. When used as fuel, wood and chlorinated waste are known sources of polychlorinated dibenzo-para-dioxins, polychlorinated dibenzofurans (PCDD/Fs), and polychlorinated biphenyls (PCBs). Here, we compare PCDD/F, dioxin-like PCB (DL-PCB), and non-DL-PCB (NDL-PCB) levels in serum of 693 Tswana individuals in the North West province, who either burn solid biofuels or have access to electricity, gas, and paraffin. This is the first South African study on dioxin levels in humans with more than 100 participants. Serum was pooled according to fuel use, as well as to confounding factors such as gender and age. Solid-phase extraction was used to remove the target analytes from serum, after which the extracts were further refined automatically using a combination of multilayer sorbents. Compound concentrations were determined by high-resolution mass spectrometry after high-resolution gas chromatography. Mean serum lipid content was determined enzymatically to be 5.91 ± 0.42 g/L. The PCDD/F and DL-PCB levels were similar to global concentrations reported for non-exposed adults. The mean of the total Toxic Equivalencies (ΣTEQ) was 6.9 ± 3.3 pg/g lipid and the mean NDL-PCB was 70.1 ± 42.8 ng/g lipid. The mean concentrations of the PCDDs, PCDFs and the corresponding World Health Organization-TEQ (WHO-TEQ) of the population using electricity, gas, and paraffin were greater than of those reliant on solid biomass (p = 0), whereas the DL-PCBs, their corresponding WHO-TEQ, and NDL-PCBs were greater for the population who use biofuels but not significantly so. The females had higher serum levels of the PCDDs (p = 0) and PCDFs (not significant) whereas the PCBs were higher for the males (p = 0). Breastfeeding women presented lower levels of all compound classes than their non-breastfeeding counterparts (p=0) and older subjects manifested greater pollutant loads than the younger generation (p = 0

Assessment of questionnaire-based PCB exposure focused on food frequency in birth cohorts in Japan.

Science.gov (United States)

Eguchi, Akifumi; Otake, Masae; Hanazato, Masamichi; Suzuki, Norimichi; Matsuno, Yoshiharu; Nakaoka, Hiroko; Todaka, Emiko; Mori, Chisato

2017-02-01

We investigated the relationship between food frequency questionnaire (FFQ) responses and serum polychlorinated biphenyl (PCB) levels of mothers and fathers recruited from the Chiba Regional Center, which is one of the 15 regional centers of the Japan Environment and Children's Study (mothers: n = 1477, fathers: n = 219). The expected PCB values were estimated from the participants' FFQ answers and medical records (age, body mass index and number of deliveries). Based on the stepwise forward selection results of Bayesian regression models, age and fish and egg consumption were positively associated with PCB concentrations and a number of deliveries were negatively associated with PCB concentrations in mothers, whereas only age was positively associated with PCB concentrations in fathers.These findings indicated that the estimation of daily dietary intake may be useful for the prediction of PCB concentration for mothers.

Uptake and depuration of PCB-153 in edible shrimp Palaemonetes varians and human health risk assessment.

Science.gov (United States)

Grilo, T F; Cardoso, P G; Pato, P; Duarte, A C; Pardal, M A

2014-03-01

A medium-term mesocosm exposure study was conducted to elucidate bioaccumulation and depuration of polychlorinated biphenyl congener 153 (PCB-153) in edible shrimp Palaemonetes varians. Over the 15-day exposure period, shrimp under different exposure concentrations exhibited a significant increase in PCB-153 concentration compared with control organisms. Distinct bioaccumulation patterns and uptake rates were observed depending on the exposure concentrations. For low PCB-153 exposure levels (0.25μgL(-1)), accumulation followed a saturation model, reaching an apparent steady state after fifteen days exposure. For intermediate (2.5μgL(-1)) and high PCB-153 levels (25μgL(-1)), accumulation was faster and linear. In addition, the bioaccumulation rate was not proportional to PCB-153 concentration, and the bioaccumulation was higher at intermediate exposure concentrations. Regarding the depuration phase, P. varians lost up to 30% of PCB-153 after 72h and levels continued slowly to decrease until the end of the 30-d experimental period. However, PCB-153 levels in shrimp did not reach background values, and those exposed to moderate and high PCB-153 concentrations presented contamination levels much higher than the regulatory limit for human food consumption (75ngg(-1) ww for Σ6 PCB). Copyright © 2013 Elsevier Inc. All rights reserved.

Direct non-destructive observation of bulk nucleation in 30% deformed aluminum

DEFF Research Database (Denmark)

West, Stine; Schmidt, Søren; Sørensen, Henning Osholm

2009-01-01

A 30% deformed aluminum sample was mapped non-destructively using three-dimensional X-ray diffraction (3DXRD) before and after annealing to nucleation of recrystallization. Nuclei appeared in the bulk of the sample. Their positions and volumes were determined, and the crystallographic orientations...... were compared with the orientations of the deformed grains. It was found that nuclei with new orientations can form and their orientations have been related to the dislocation structure in the deformed grains....

PCB pollution continues to impact populations of orcas and other dolphins in European waters

Science.gov (United States)

Jepson, Paul D.; Deaville, Rob; Barber, Jonathan L.; Aguilar, Àlex; Borrell, Asunción; Murphy, Sinéad; Barry, Jon; Brownlow, Andrew; Barnett, James; Berrow, Simon; Cunningham, Andrew A.; Davison, Nicholas J.; Ten Doeschate, Mariel; Esteban, Ruth; Ferreira, Marisa; Foote, Andrew D.; Genov, Tilen; Giménez, Joan; Loveridge, Jan; Llavona, Ángela; Martin, Vidal; Maxwell, David L.; Papachlimitzou, Alexandra; Penrose, Rod; Perkins, Matthew W.; Smith, Brian; de Stephanis, Renaud; Tregenza, Nick; Verborgh, Philippe; Fernandez, Antonio; Law, Robin J.

2016-01-01

Organochlorine (OC) pesticides and the more persistent polychlorinated biphenyls (PCBs) have well-established dose-dependent toxicities to birds, fish and mammals in experimental studies, but the actual impact of OC pollutants on European marine top predators remains unknown. Here we show that several cetacean species have very high mean blubber PCB concentrations likely to cause population declines and suppress population recovery. In a large pan-European meta-analysis of stranded (n = 929) or biopsied (n = 152) cetaceans, three out of four species:- striped dolphins (SDs), bottlenose dolphins (BNDs) and killer whales (KWs) had mean PCB levels that markedly exceeded all known marine mammal PCB toxicity thresholds. Some locations (e.g. western Mediterranean Sea, south-west Iberian Peninsula) are global PCB “hotspots” for marine mammals. Blubber PCB concentrations initially declined following a mid-1980s EU ban, but have since stabilised in UK harbour porpoises and SDs in the western Mediterranean Sea. Some small or declining populations of BNDs and KWs in the NE Atlantic were associated with low recruitment, consistent with PCB-induced reproductive toxicity. Despite regulations and mitigation measures to reduce PCB pollution, their biomagnification in marine food webs continues to cause severe impacts among cetacean top predators in European seas.

PCB pollution continues to impact populations of orcas and other dolphins in European waters.

Science.gov (United States)

Jepson, Paul D; Deaville, Rob; Barber, Jonathan L; Aguilar, Àlex; Borrell, Asunción; Murphy, Sinéad; Barry, Jon; Brownlow, Andrew; Barnett, James; Berrow, Simon; Cunningham, Andrew A; Davison, Nicholas J; Ten Doeschate, Mariel; Esteban, Ruth; Ferreira, Marisa; Foote, Andrew D; Genov, Tilen; Giménez, Joan; Loveridge, Jan; Llavona, Ángela; Martin, Vidal; Maxwell, David L; Papachlimitzou, Alexandra; Penrose, Rod; Perkins, Matthew W; Smith, Brian; de Stephanis, Renaud; Tregenza, Nick; Verborgh, Philippe; Fernandez, Antonio; Law, Robin J

2016-01-14

Organochlorine (OC) pesticides and the more persistent polychlorinated biphenyls (PCBs) have well-established dose-dependent toxicities to birds, fish and mammals in experimental studies, but the actual impact of OC pollutants on European marine top predators remains unknown. Here we show that several cetacean species have very high mean blubber PCB concentrations likely to cause population declines and suppress population recovery. In a large pan-European meta-analysis of stranded (n = 929) or biopsied (n = 152) cetaceans, three out of four species:- striped dolphins (SDs), bottlenose dolphins (BNDs) and killer whales (KWs) had mean PCB levels that markedly exceeded all known marine mammal PCB toxicity thresholds. Some locations (e.g. western Mediterranean Sea, south-west Iberian Peninsula) are global PCB "hotspots" for marine mammals. Blubber PCB concentrations initially declined following a mid-1980s EU ban, but have since stabilised in UK harbour porpoises and SDs in the western Mediterranean Sea. Some small or declining populations of BNDs and KWs in the NE Atlantic were associated with low recruitment, consistent with PCB-induced reproductive toxicity. Despite regulations and mitigation measures to reduce PCB pollution, their biomagnification in marine food webs continues to cause severe impacts among cetacean top predators in European seas.

Total and non-seasalt sulfate and chloride measured in bulk precipitation samples from the Kilauea Volcano area, Hawaii

Science.gov (United States)

Scholl, M.A.; Ingebritsen, S.E.

1995-01-01

Six-month cumulative precipitation samples provide estimates of bulk deposition of sulfate and chloride for the southeast part of the Island of Hawaii during four time periods: August 1991 to February 1992, February 1992 to September 1992, March 1993 to September 1993, and September 1993 to February 1994. Total estimated bulk deposition rates for sulfate ranged from 0.12 to 24 grams per square meter per 180 days, and non-seasalt sulfate deposition ranged from 0.06 to 24 grams per square meter per 180 days. Patterns of non-seasalt sulfate deposition were generally related to prevailing wind directions and the proximity of the collection site to large sources of sulfur gases, namely Kilauea Volcano's summit and East Rift Zone eruption. Total chloride deposition from bulk precipitation samples ranged from 0.01 to 17 grams per square meter per 180 days. Chloride appeared to be predominantly from oceanic sources, as non- seasalt chloride deposition was near zero for most sites.

Investigation of fatigue strength of tool steels in sheet-bulk metal forming

Science.gov (United States)

Pilz, F.; Gröbel, D.; Merklein, M.

2018-05-01

To encounter trends regarding an efficient production of complex functional components in forming technology, the process class of sheet-bulk metal forming (SBMF) can be applied. SBMF is characterized by the application of bulk forming operations on sheet metal, often in combination with sheet forming operations [1]. The combination of these conventional process classes leads to locally varying load conditions. The resulting load conditions cause high tool loads, which lead to a reduced tool life, and an uncontrolled material flow. Several studies have shown that locally modified tool surfaces, so-called tailored surfaces, have the potential to control the material flow and thus to increase the die filling of functional elements [2]. A combination of these modified tool surfaces and high tool loads in SBMF is furthermore critical for the tool life and leads to fatigue. Tool fatigue is hardly predictable and due to a lack of data [3], a challenge in tool design. Thus, it is necessary to provide such data for tool steels used in SBMF. The aim of this study is the investigation of the influence of tailored surfaces on the fatigue strength of the powder metallurgical tool steel ASP2023 (1.3344, AISI M3:2), which is typically used in cold forging applications, with a hardness 60 HRC ± 1 HRC. To conduct this investigation, the rotating bending test is chosen. As tailored surfaces, a DLC-coating and a surface manufactured by a high-feed-milling process are chosen. As reference a polished surface which is typical for cold forging tools is used. Before the rotating bending test, the surface integrity is characterized by measuring topography and residual stresses. After testing, the determined values of the surface integrity are correlated with the reached fracture load cycle to derive functional relations. Based on the gained results the investigated tailored surfaces are evaluated regarding their feasibility to modify tool surfaces within SBMF.

Associations between plasma concentrations of PCB 28 and possible indoor exposure sources in Danish school children and mothers.

Science.gov (United States)

Egsmose, Emilie Lund; Bräuner, Elvira Vaclavik; Frederiksen, Marie; Mørck, Thit Aarøe; Siersma, Volkert Dirk; Hansen, Pernille Winton; Nielsen, Flemming; Grandjean, Philippe; Knudsen, Lisbeth E

2016-02-01

Polychlorinated biphenyls (PCBs) are ubiquitously present in the environment and are suspected of carcinogenic, neurotoxic and immunotoxic effects. Significantly higher plasma concentrations of the congener PCB 28 occur in children compared to adults. Exposure in schools may contribute to this difference. To determine whether increased blood plasma concentrations of PCB 28 in Danish school children and mothers are associated with living in homes or attending schools constructed in the PCB period (1959-1977). PCB 28 was analyzed in plasma samples from 116 children aged 6-11years and 143 mothers living in an urban and a rural area in Denmark and participating in the European pilot project DEMOCOPHES (Demonstration of a study to COordinate and Perform Human Biomonitoring on a European Scale). In Denmark, PCBs were used in construction in the period 1950-1977, and year of construction or renovation of the homes and schools was used as a proxy for indoor PCB exposure. Linear regression models were used to assess the association between potential PCB exposure from building materials and lipid adjusted concentrations of PCB 28 in plasma, with and without adjustment for potential confounders. Among the 116 children and 143 mothers, we were able to specify home construction period in all but 4 children and 5 mothers leaving 111 children and 138 mothers for our analyses. The median lipid adjusted plasma PCB 28 concentration was 3 (range: 1-28) ng/g lipid in the children and 2 (range: 1-8) ng/g lipid in the mothers. Children living in homes built in the PCB period had significantly higher lipid adjusted plasma PCB 28 concentrations compared to children living in homes built before or after the PCB period. Following adjustment for covariates, PCB 28 concentrations in children were 40 (95% CI: 13; 68) percent higher than concentrations of children living in homes constructed at other times. Furthermore, children attending schools built or substantially refurbished in the PCB

ZrCuAl Bulk Metallic Glass spall induced by laser shock

Science.gov (United States)

Jodar, Benjamin; Loison, Didier; Yokoyama, Yoshihiko; Lescoute, Emilien; Berthe, Laurent; Sangleboeuf, Jean-Christophe

2017-06-01

To face High Velocity Impacts, the aerospace industry is always seeking for innovative materials usable as debris shielding components. Bulk Metallic Glasses (BMG) revealed interesting mechanical properties in case of static and quasi-static loading conditions: high elasticity, high tenacity, low density and high fracture threshold... The department of Mechanics and Glass of the Institut of Physics Rennes conducted on the ELFIE facility, laser shock experiments to study the behavior of a ternary ZrCuAl BMG under high strain rate, up-to fragmentation process. On the one hand, in-situ diagnostics were used to measure ejection velocities with PDV and debris morphologies were observed by Shadowgraphy. On the other hand, spalled areas (dimensions and features) were characterized through post-mortem analysis (optical observations, profilometry and SEM). These results are compared to experimental and numerical data on the crystalline forms of the ZrCuAl basic compounds.

Reentrant spin glass ordering in an Fe-based bulk metallic glass

Energy Technology Data Exchange (ETDEWEB)

Luo, Qiang; Shen, Jun, E-mail: junshen@tongji.edu.cn [School of Materials Science and Engineering, Tongji University, Shanghai 201804 (China)

2015-02-07

We report the results of the complex susceptibility, temperature, and field dependence of DC magnetization and the nonequilibrium dynamics of a bulk metallic glass Fe{sub 40}Co{sub 8}Cr{sub 15}Mo{sub 14}C{sub 15}B{sub 6}Er{sub 2}. Solid indication of the coexistence of reentrant spin glass (SG) and ferromagnetic orderings is determined from both DC magnetization and AC susceptibility under different DC fields. Dynamics scaling of AC susceptibility indicates critical slowing down to a reentrant SG state with a static transition temperature T{sub s} = ∼17.8 K and a dynamic exponent zv = ∼7.3. The SG nature is further corroborated from chaos and memory effects, magnetic hysteresis, and aging behavior. We discuss the results in terms of the competition among random magnetic anisotropy and exchange interactions and compare them with simulation predictions.

Performance simulation of serpentine type metallic and non-metallic solar collector

International Nuclear Information System (INIS)

Al-Sageer, A. A. M.; Alowa, M. I.; Saad, M.

2006-01-01

This paper presents a theoretical investigation of metallic and non-metalic solar water collector models for evaluating its performane parameters. The determined parameters include heat removal factor , overall heat loss coefficients, heat gain, daily and hourly efficiencies. The present study reports that, under forced circulation lest, the non-metallic collector has an inferior performance parameters when compared to that of the metallic one. It was also revealed that the overall heat loss coefficients of both collectors show weak dependence on the flow rate variations. It was also noticed that the heat removal factor forboth models is more sensitive to the flow rate variations. Also noticed that the heat removal factor for both models is more sensitive to the flow rate variations. Also, a comparision of performance parameters of the theoretical and experimental studies showed good agreements for most hours of the day, except the results obtained at the early morning and late after noon hours.(Author)

Optimal production planning for PCB assembly

CERN Document Server

Ho, William

2006-01-01

Focuses on the optimization of the Printed circuit board (PCB) assembly lines' efficiency. This book integrates the component sequencing and the feeder arrangement problems together for the pick-and-place machine and the chip shooter machines.

PCDD, PCDF, and PCB contamination of air and inhalable particulate in Rome

International Nuclear Information System (INIS)

Turrio-Baldassarri, L.; Carere, A.; Di Domenico, A.; Fuselli, S.; Iacovella, N.; Rodriguez, F.

1994-01-01

The isomer specific determination of PCDD, PCDF and PCB was carried out on samples of air and inhalable particulate from Rome. Samples were taken daily for six months and pooled to yield two samples per month. Normal PCDD + PCDF concentrations expressed in TEQ ranged from 48 to 87 fg/m 3 , while total PCB ranged from 0.1 to 1.4 ng/m 3 . The 2, 3, 7, 8-substituted PCDD and PCDF congener pattern is shown together with the PCB congener pattern. (orig.)

2,2',3,3',6,6'-Hexachlorobiphenyl (PCB 136) is Enantioselectively Oxidized to Hydroxylated Metabolites by Rat Liver Microsomes

Science.gov (United States)

Wu, Xianai; Pramanik, Ananya; Duffel, Michael W.; Hrycay, Eugene G.; Bandiera, Stelvio M.; Lehmler, Hans-Joachim; Kania-Korwel, Izabela

2011-01-01

Developmental exposure to multiple-ortho substituted polychlorinated biphenyls (PCBs) causes adverse neurodevelopmental outcomes in laboratory animals and humans by mechanisms involving the sensitization of Ryanodine receptors (RyRs). In the case of PCB 136, the sensitization of RyR is enantiospecific, with only (-)-PCB 136 being active. However, the role of enantioselective metabolism in the developmental neurotoxicity of PCB 136 is poorly understood. The present study employed hepatic microsomes from phenobarbital (PB-), dexamethasone (DEX-) and corn oil (VEH-)treated male Sprague-Dawley rats to investigate the hypothesis that PCB 136 atropisomers are enantioselectively metabolized by P450 enzymes to potentially neurotoxic, hydroxylated PCB 136 metabolites. The results demonstrated the time- and isoform-dependent formation of three metabolites, with 5-OH-PCB 136 (2,2',3,3',6,6'-hexachlorobiphenyl-5-ol) being the major metabolite. The formation of 5-OH-PCB 136 increased with the activity of P450 2B enzymes in the microsomal preparation, which is consistent with PCB 136 metabolism by rat P450 2B1. The minor metabolite 4-OH-PCB 136 (2,2',3,3',6,6'-hexachlorobiphenyl-4-ol) was produced by a currently unidentified P450 enzymes. An enantiomeric enrichment of (-)-PCB 136 was observed in microsomal incubations due to the preferential metabolism of (+)-PCB 136 to the corresponding 5-OH-PCB 136 (2,2',3,3',6,6'-hexachlorobiphenyl-5-ol) atropisomer. 4-OH-PCB 136 displayed an enrichment of the atropisomer formed from (-)-PCB 136; however, the enrichment of this metabolite atropisomer didn't affect the enantiomeric enrichment of the parent PCB because 4-OH-PCB 136 is only a minor metabolite. Although the formation of 5- and 4-OH-PCB 136 atropisomers increased with time, the enantioselective formation of the OH-PCB metabolites resulted in constant enantiomeric enrichment, especially at later incubation times. These observations not only demonstrate that the chiral signatures of

Fasting augments PCB impact on liver metabolism in anadromous Arctic Char

Science.gov (United States)

Vijayan, M.M.; Aluru, N.; Maule, A.G.; Jorgensen, E.H.

2006-01-01

Anadromous arctic char (Salvelinus alpinus) undertake short feeding migrations to seawater every summer and accumulate lipids, while the rest of the year is spent in fresh water where the accumulated lipid reserves are mobilized. We tested the hypothesis that winter fasting and the associated polychlorinated biphenyls' (PCBs) redistribution from lipid depots to critical tissues impair the liver metabolic capacity in these animals. Char were administered Aroclor 1254 (0, 1, 10, and 100 mg/ kg body mass) orally and maintained for 4 months without feeding to mimic seasonal winter fasting, while fed groups (0 and 100 mg Aroclor 1254/kg) were maintained for comparison. A clear dose-related increase in PCB accumulation and cytochrome P4501A (CYP1A) protein content was observed in the livers of fasted fish. This PCB concentration and CYP1A response with the high dose of Aroclor were 1.5-fold and 3-fold greater in the fasted than in the fed fish, respectively. In fed fish, PCB exposure lowered liver glycogen content, whereas none of the other metabolic indicators were significantly affected. In fasted fish, PCB exposure depressed liver glycogen content and activities of glucose-6-phosphate dehydrogenase, alanine aminotransferase, lactate dehydrogenase, and phosphoenolpyruvate carboxykinase and elevated 3-hydroxyacylcoA dehydrogenase activity and glucocorticoid receptor protein expression. There were no significant impacts of PCB on heat shock protein 70 (hsp70) and hsp90 contents in either fed or fasted fish. Collectively, our study demonstrates that winter emaciation associated with the anadromous lifestyle predisposes arctic char to PCB impact on hepatic metabolism including disruption of the adaptive metabolic responses to extended fasting. ?? 2006 Oxford University Press.

Induction detection of concealed bulk banknotes

Science.gov (United States)

Fuller, Christopher; Chen, Antao

2012-06-01

The smuggling of bulk cash across borders is a serious issue that has increased in recent years. In an effort to curb the illegal transport of large numbers of paper bills, a detection scheme has been developed, based on the magnetic characteristics of bank notes. The results show that volumes of paper currency can be detected through common concealing materials such as plastics, cardboard, and fabrics making it a possible potential addition to border security methods. The detection scheme holds the potential of also reducing or eliminating false positives caused by metallic materials found in the vicinity, by observing the stark difference in received signals caused by metal and currency. The detection scheme holds the potential to detect for both the presence and number of concealed bulk notes, while maintaining the ability to reduce false positives caused by metal objects.

Optimization of key factors of the electrostatic separation for crushed PCB wastes using roll-type separator

International Nuclear Information System (INIS)

Wu Jiang; Li Jia; Xu Zhenming

2008-01-01

For the electrostatic separation process, the separator is most crucial. As a classical one, the roll-type corona-electrostatic separator has some advantages in recycle of waste electrical and electronic equipment (WEEE). Some researches have been done in this field and shown that there was a complex correlation between its configuration and the efficiency of the separation. In this paper, a fractional factorial design (2 v 1-5 ) was built and 32 tests were performed on a roll-type corona-electrostatic separator. The sample of granular mixture got from crushed PCB wastes (size 0.3-0.45 mm, containing 25% metal and 75% nonmetal). The experimental data were discussed and used to analyze the factors' main effect, interaction and optimization of the process. Three liner-interaction mathematical models were derived to describe the mass of middling fraction (M), conductor fraction (C) and Nonconductor fraction (NC), respectively. The results show that the efficiency of the PCB waste electrostatic separation process has a significant correlation with not only factors' main effects, but also the interaction between them

Bulk characterization methods for non-centrosymmetric materials: second-harmonic generation, piezoelectricity, pyroelectricity, and ferroelectricity.

Science.gov (United States)

Ok, Kang Min; Chi, Eun Ok; Halasyamani, P Shiv

2006-08-01

Characterization methods for bulk non-centrosymmetric compounds are described. These methods include second-harmonic generation, piezoelectricity, pyroelectricity, and ferroelectricity. In this tutorial review with each phenomenon, details are given of the measurement techniques along with a brief history and background. Finally, data interpretation is discussed.

Individual Polychlorinated Biphenyl (PCB) Congeners Produce Tissue- and Gene-Specific Effects on Thyroid Hormone Signaling during Development

Science.gov (United States)

Giera, Stefanie; Bansal, Ruby; Ortiz-Toro, Theresa M.; Taub, Daniel G.

2011-01-01

Polychlorinated biphenyls (PCB) are industrial chemicals linked to developmental deficits that may be caused in part by disrupting thyroid hormone (TH) action by either reducing serum TH or interacting directly with the TH receptor (TR). Individual PCB congeners can activate the TR in vitro when the metabolic enzyme cytochrome P4501A1 (CYP1A1) is induced, suggesting that specific PCB metabolites act as TR agonists. To test this hypothesis in vivo, we compared two combinations of PCB congeners that either activate the TR (PCB 105 and 118) or not (PCB 138 and 153) in the presence or absence of a PCB congener (PCB 126) that induces CYP1A1 in vitro. Aroclor 1254 was used as a positive control, and a group treated with propylthiouracil was included to characterize the effects of low serum TH. We monitored the effects on TH signaling in several peripheral tissues by measuring the mRNA expression of well-known TH-response genes in these tissues. Aroclor 1254 and its component PCB 105/118/126 reduced total T4 to the same extent as that of propylthiouracil but increased the expression of some TH target genes in liver. This effect was strongly correlated with CYP1A1 expression supporting the hypothesis that metabolism is necessary. Effects were gene and tissue specific, indicating that tissue-specific metabolism is an important component of PCB disruption of TH action and that PCB metabolites interact in complex ways with the TR. These are essential mechanisms to consider when evaluating the health risks of contaminant exposures, for both PCB and other polycyclic compounds known to interact with nuclear hormone receptors. PMID:21540284

PCB concentrations and activity of sea lamprey Petromyzon marinus vary by sex

Science.gov (United States)

Madenjian, Charles P.; Johnson, Nicholas S.; Binder, Thomas R.; Rediske, Richard R.; O'Keefe, James P.

2013-01-01

We determined the polychlorinated biphenyl (PCB) concentrations of 40 male and 40 female adult sea lampreys Petromyzon marinus captured in the Cheboygan River, a tributary to Lake Huron, during May 2011. In addition, we performed a laboratory experiment using passive integrated transponder tags to determine whether male adult sea lampreys were more active than female adult sea lampreys. Sex had a significant effect on PCB concentration, and PCB concentration at a given level of sea lamprey condition was approximately 25 % greater in males than in females. Adjusting for the difference in condition between the sexes, males averaged a 17 % greater PCB concentration compared with females. Results from the laboratory experiment indicated that males were significantly more active than females. The observed sex difference in PCB concentrations was not due to female sea lampreys releasing eggs at spawning because the sea lamprey is semelparous, and we caught the sea lampreys before spawning. Rather, we attributed the sex difference in PCB concentrations to a greater rate of energy expenditure in males compared with females. We proposed that this greater rate of energy expenditure was likely due to greater activity. Our laboratory experiment results supported this hypothesis. A greater resting metabolic rate may also have contributed to a greater rate of energy expenditure. Our findings should eventually be applicable toward improving control of sea lamprey, a pest responsible for considerable damage to fisheries in lakes where it is not native.

77 FR 11533 - Anniston PCB Superfund Site, Anniston, Calhoun County, Alabama; Notice of Amended Settlement

Science.gov (United States)

2012-02-27

... ENVIRONMENTAL PROTECTION AGENCY [CERCLA-04-2012-3763; FRL 9637-7] Anniston PCB Superfund Site... past response costs concerning the Anniston PCB Superfund Site located in Anniston, Calhoun County.... Submit your comments by Site name Anniston PCB by one of the following methods: www.epa.gov/region4...

Preparation and characterization of rare-earth bulks with controllable nanostructures

International Nuclear Information System (INIS)

Song Xiaoyan; Zhang Jiuxing; Li Erdong; Lu Nianduan; Yin Fuxing

2006-01-01

The preparation and characterization of pure rare-earth-metal bulks with controllable nanostructures are reported in this paper. A novel 'oxygen-free' in situ synthesis technique that combines inert-gas condensation with spark plasma sintering (SPS) technology is proposed. Taking into account the special mechanisms of SPS consolidation and the scale effects of nanoparticles, we introduced practical procedures for preparing rare-earth bulks of amorphous, mixed amorphous and nanocrystals, and nanocrystalline microstructures, respectively. Compared with the conventional polycrystalline bulk, these nanostructured bulks exhibit substantially improved physical and mechanical properties. This technique enables comprehensive studies on the microstructures and properties of a large variety of nanostructured metallic materials that are highly reactive in the air

Insight in the PCB-degrading functional community in long-term contaminated soil under bioremediation

Energy Technology Data Exchange (ETDEWEB)

Petric, Ines; Hrsak, Dubravka; Udikovic-Kolic, Nikolina [Ruder Boskovic Inst., Division for Marine and Environmental Research, Zagreb (Croatia); Fingler, Sanja [Inst. for Medical Research and Occupational Health, Zagreb (Croatia); Bru, David; Martin-Laurent, Fabrice [INRA, Univ. der Bourgogne, Soil and Environmental Microbiology, Dijon (France)

2011-02-15

A small-scale bioremediation assay was developed in order to get insight into the functioning of a polychlorinated biphenyl (PCB) degrading community during the time course of bioremediation treatment of a contaminated soil. The study was conducted with the aim to better understand the key mechanisms involved in PCB-removal from soils. Materials and methods Two bioremediation strategies were applied in the assay: (a) biostimulation (addition of carvone as inducer of biphenyl pathway, soya lecithin for improving PCB bioavailability, and xylose as supplemental carbon source) and (b) bioaugmentation with selected seed cultures TSZ7 or Rhodococcus sp. Z6 originating from the transformer station soil and showing substantial PCB-degrading activity. Functional PCB-degrading community was investigated by using molecular-based approaches (sequencing, qPCR) targeting bphA and bphC genes, coding key enzymes of the upper biphenyl pathway, in soil DNA extracts. In addition, kinetics of PCBs removal during the bioremediation treatment was determined using gas chromatography mass spectrometry analyses. Results and discussion bphA-based phylogeny revealed that bioremediation affected the structure of the PCB-degrading community in soils, with Rhodococcus-like bacterial populations developing as dominant members. Tracking of this population further indicated that applied bioremediation treatments led to its enrichment within the PCB-degrading community. The abundance of the PCB-degrading community, estimated by quantifying the copy number of bphA and bphC genes, revealed that it represented up to 0.3% of the total bacterial community. All bioremediation treatments were shown to enhance PCB reduction in soils, with approximately 40% of total PCBs being removed during a 1-year period. The faster PCB reduction achieved in bioaugmented soils suggested an important role of the seed cultures in bioremediation processes. Conclusions The PCBs degrading community was modified in response to

Life Cycle Analysis for Treatment and Disposal of PCB Waste at Ashtabula and Fernald

International Nuclear Information System (INIS)

Morris, M.I.

2001-01-01

This report presents the use of the life cycle analysis (LCA) system developed at Oak Ridge National Laboratory (ORNL) to assist two U.S. Department of Energy (DOE) sites in Ohio--the Ashtabula Environmental Management Project near Cleveland and the Fernald Environmental Management Project near Cincinnati--in assessing treatment and disposal options for polychlorinated biphenyl (PCB)-contaminated low-level radioactive waste (LLW) and mixed waste. We will examine, first, how the LCA process works, then look briefly at the LCA system's ''toolbox,'' and finally, see how the process was applied in analyzing the options available in Ohio. As DOE nuclear weapons facilities carry out planned decontamination and decommissioning (D and D) activities for site closure and progressively package waste streams, remove buildings, and clean up other structures that have served as temporary waste storage locations, it becomes paramount for each waste stream to have a prescribed and proven outlet for disposition. Some of the most problematic waste streams throughout the DOE complex are PCB low-level radioactive wastes (liquid and solid) and PCB low-level Resource Conservation and Recovery Act (RCRA) liquid and solid wastes. Several DOE Ohio Field Office (OH) sites have PCB disposition needs that could have an impact on the critical path of the decommissioning work of these closure sites. The Ashtabula Environmental Management Project (AEMP), an OH closure site, has an urgent problem with disposition of soils contaminated by PCB and low-level waste at the edge of the site. The Fernald Environmental Management Project (FEMP), another OH closure site, has difficulties in timely disposition of its PCB-low-level sludges and its PCB low-level RCRA sludges in order to avoid impacting the critical path of its D and D activities. Evaluation of options for these waste streams is the subject of this report. In the past a few alternatives for disposition of PCB low-level waste and PCB low

Life Cycle Analysis for Treatment and Disposal of PCB Waste at Ashtabula and Fernald

Energy Technology Data Exchange (ETDEWEB)

Morris, M.I.

2001-01-11

This report presents the use of the life cycle analysis (LCA) system developed at Oak Ridge National Laboratory (ORNL) to assist two U.S. Department of Energy (DOE) sites in Ohio--the Ashtabula Environmental Management Project near Cleveland and the Fernald Environmental Management Project near Cincinnati--in assessing treatment and disposal options for polychlorinated biphenyl (PCB)-contaminated low-level radioactive waste (LLW) and mixed waste. We will examine, first, how the LCA process works, then look briefly at the LCA system's ''toolbox,'' and finally, see how the process was applied in analyzing the options available in Ohio. As DOE nuclear weapons facilities carry out planned decontamination and decommissioning (D&D) activities for site closure and progressively package waste streams, remove buildings, and clean up other structures that have served as temporary waste storage locations, it becomes paramount for each waste stream to have a prescribed and proven outlet for disposition. Some of the most problematic waste streams throughout the DOE complex are PCB low-level radioactive wastes (liquid and solid) and PCB low-level Resource Conservation and Recovery Act (RCRA) liquid and solid wastes. Several DOE Ohio Field Office (OH) sites have PCB disposition needs that could have an impact on the critical path of the decommissioning work of these closure sites. The Ashtabula Environmental Management Project (AEMP), an OH closure site, has an urgent problem with disposition of soils contaminated by PCB and low-level waste at the edge of the site. The Fernald Environmental Management Project (FEMP), another OH closure site, has difficulties in timely disposition of its PCB-low-level sludges and its PCB low-level RCRA sludges in order to avoid impacting the critical path of its D&D activities. Evaluation of options for these waste streams is the subject of this report. In the past a few alternatives for disposition of PCB low-level waste

Bulk-mediated surface diffusion: non-Markovian desorption and biased behaviour in an infinite system

International Nuclear Information System (INIS)

Revelli, Jorge A; Budde, Carlos E; Wio, Horacio S

2005-01-01

We analyse the dynamics of adsorbed molecules within the bulk-mediated surface diffusion framework. We consider that the particle's desorption mechanism is characterized by a non-Markovian process, while the particle's adsorption and its motion in the bulk are governed by Markovian dynamics, and include the effect of an external field in the form of a bias in the normal motion to the surface. We study this system for the diffusion of particles in a semi-infinite lattice, analysing the conditional probability to find the system on the reference absorptive plane as well as the surface dispersion as functions of time. The agreement between numerical and analytical asymptotic results is discussed

Formation of bulk metallic glasses in the Fe-M-Y-B (M = transition metal) system

Energy Technology Data Exchange (ETDEWEB)

Huang, X.M. [International Center for New-Structured Materials (ICNSM) and Laboratory of New-Structured Materials, Department of Materials Science and Engineering, Zhejiang University, Hangzhou 310027 (China); Chang, C.T. [Institute for Material Research, Tohoku University, Sendai 980-8577 (Japan); Chang, Z.Y.; Wang, X.D.; Cao, Q.P. [International Center for New-Structured Materials (ICNSM) and Laboratory of New-Structured Materials, Department of Materials Science and Engineering, Zhejiang University, Hangzhou 310027 (China); Shen, B.L.; Inoue, A. [Institute for Material Research, Tohoku University, Sendai 980-8577 (Japan); Jiang, J.Z. [International Center for New-Structured Materials (ICNSM) and Laboratory of New-Structured Materials, Department of Materials Science and Engineering, Zhejiang University, Hangzhou 310027 (China)], E-mail: jiangjz@zju.edu.cn

2008-07-28

In this work, quaternary Fe{sub 72-x}M{sub x}Y{sub 6}B{sub 22} (M = Ni, Co and Mo) bulk metallic glasses (BMGs) have been developed. It is found that a fully amorphous Fe{sub 68}Mo{sub 4}Y{sub 6}B{sub 22} cylindrical rod with 6.5 mm in diameter can be prepared by copper mold injection. These alloys have a high glass transition temperature of about 900 K with high fracture strengths up to about 3 GPa although they are still brittle. Magnetic measurements reveal that they are ferromagnetic at ambient temperature with low coercive force of about 2 A/m, saturation magnetization of about 0.7 T and effective permeability of about 7000 at 100 kHz. The newly developed Fe-based quaternary alloys exhibit excellent combination properties: superior glass forming ability (GFA), high glass transition temperature, and soft magnetic properties, which could have potential applications in electronic industries. Furthermore, the effect of Mo addition on GFA in the Fe-Y-B BMG system has been discussed compared with those of Ni and Co additions.

Kwantificatie van PCB-componenten in krachtvoeders

NARCIS (Netherlands)

Mazijk, van R.J.; Munsteren, van A.J.; Tuinstra, L.G.M.Th.

1981-01-01

Met behulp van individuele chloorbifenylstandaarden is het PCB-gehalte van een aantal krachtvoeders bepaald, waarbij voor de onbekende componenten een geschatte waarde is gebruikt. Uit deze gehalten is met behulp van omrekeningsfactoren de theoretische DCB-opbrengst bij perchloreren berekend. Dit

Improvement of corrosion resistance in NaOH solution and glass forming ability of as-cast Mg-based bulk metallic glasses by microalloying

Directory of Open Access Journals (Sweden)

Peng Hao

2011-02-01

Full Text Available The influences of the addition of Ag on the glass forming ability (GFA and corrosion behavior were investigated in the Mg-Ni-based alloy system by X-ray diffraction (XRD and electrochemical polarization in 0.1 mol/L NaOH solution. Results shows that the GFA of the Mg-Ni-based BMGs can be improved dramatically by the addition of an appropriate amount of Ag; and the addition element Ag can improve the corrosion resistance of Mg-Ni-based bulk metallic glass. The large difference in atomic size and large negative mixing enthalpy in alloy system can contribute to the high GFA. The addition element Ag improves the forming speed and the stability of the passive film, which is helpful to decrease the passivation current density and to improve the corrosion resistance of Mg-Ni-based bulk metallic glass.

PCB transformer fires: the risk in nuclear power plants

International Nuclear Information System (INIS)

Blackmon, K.

1988-01-01

It is estimated that 1/2 of the present nuclear power plants operate with PCB-filled transformer equipment. In an attempt to obtain better estimates of clean-up costs in a nuclear power plant under reasonable-loss scenarios, a study was commissioned. This study was a joint venture between Blackmon-Mooring Steamatic Technologies, Inc., (BMS-TECH) and M and M Protection Consultants. This joint study was conducted at a typical pressurized-water reactor plant consisting of two 1000-MW units. Three specific scenarios were selected and analyzed for this typical power plant. These scenarios were: (1) an electrical failure of a transformer in an isolated switch gear room; (2) a transformer exposed to a 55-gallon transient combustion oil fire in the auxiliary building; and (3) a PCB transformer involved in a major turbine lube fire in the turbine building. Based on results of this study, the insurance carriers for this industry implemented an adjustment in their rate structures for nuclear power plants that have PCB equipment

Exposure in utero to 2,2',3,3',4,6'-hexachlorobiphenyl (PCB 132) impairs sperm function and alters testicular apoptosis-related gene expression in rat offspring

International Nuclear Information System (INIS)

Hsu, P.-C.; Pan, M.-H.; Li, L.-A.; Chen, C.-J.; Tsai, S.-S.; Guo, Y.L.

2007-01-01

Toxicity of the polychlorinated biphenyls (PCBs) depends on their molecular structure. Mechanisms by prenatal exposure to a non-dioxin-like PCB, 2,2',3,4',5',6-hexachlorobiphenyl (PCB 132) that may act on reproductive pathways in male offspring are relatively unknown. The purpose was to determine whether epididymal sperm function and expression of apoptosis-related genes were induced or inhibited by prenatal exposure to PCB 132. Pregnant rats were treated with a single dose of PCB 132 at 1 or 10 mg/kg on gestational day 15. Male offspring were killed and the epididymal sperm counts, motility, velocity, reactive oxygen species (ROS) generation, sperm-oocyte penetration rate (SOPR), testicular histopathology, apoptosis-related gene expression and caspase activation were assessed on postnatal day 84. Prenatal exposure to PCB 132 with a single dose of 1 or 10 mg/kg decreased cauda epididymal weight, epididymal sperm count and motile epididymal sperm count in adult offspring. The spermatozoa of PCB 132-exposed offspring produced significantly higher levels of ROS than the controls; ROS induction and SOPR reduction were dose-related. In the low-dose PCB 132 group, p53 was significantly induced and caspase-3 was inhibited. In the high-dose group, activation of caspase-3 and -9 was significantly increased, while the expressions of Fas, Bax, bcl-2, and p53 genes were significantly decreased. Gene expression and caspase activation data may provide insight into the mechanisms by which exposure to low-dose or high-dose PCB 132 affects reproduction in male offspring in rats. Because the doses of PCB 132 administered to the dams were approximately 625-fold in low-dose group and 6250-fold higher in high-dose group than the concentration in human tissue levels, the concentrations are not biologically or environmentally relevant. Further studies using environmentally relevant doses are needed for hazard identification

Crystallization in Zr41.2Ti13.8Cu12.5Ni10Be22.5 bulk metallic glass under pressure

DEFF Research Database (Denmark)

Jiang, Jianzhong; Zhou, T.J.; Rasmussen, Helge Kildahl

2000-01-01

The effect of pressure on the crystallization behavior of the bulk metallic glass-forming Zr41.2Ti13.8Cu12.5Ni10Be22.5 alloy with a wide supercooled liquid region has been investigated by in situ high-pressure and high-temperature x-ray powder diffraction measurements using synchrotron radiation......)], reporting a decrease of the crystallization temperature under pressure in a pressure range of 0-6 GPa for the bulk glass Zr41Ti14Cu12.5Ni9Be22.5C1 alloy. Compressibility with a volume reduction of approximately 22% at room temperature does not induce crystallization in the Zr41.2Ti13.8Cu12.5Ni10Be22.5 bulk...... glass alloy. This indicates that the densification effect induced by pressure in the pressure range investigated plays a minor role in the crystallization behavior of this bulk glass alloy. The different crystallization behavior of the carbon-free and the carbon-containing glassy alloys has been...

New Ti-based Ti–Cu–Zr–Fe–Sn–Si–Ag bulk metallic glass for biomedical applications

Energy Technology Data Exchange (ETDEWEB)

Pang, Shujie; Liu, Ying; Li, Haifei; Sun, Lulu [Key Laboratory of Aerospace Materials and Performance (Ministry of Education), School of Materials Science and Engineering, Beihang University, Beijing 100191 (China); Li, Yan [Key Laboratory of Aerospace Materials and Performance (Ministry of Education), School of Materials Science and Engineering, Beihang University, Beijing 100191 (China); Beijing Key Laboratory for Advanced Functional Materials and Thin Film Technology, Beihang University, Beijing 100191 (China); Zhang, Tao, E-mail: zhangtao@buaa.edu.cn [Key Laboratory of Aerospace Materials and Performance (Ministry of Education), School of Materials Science and Engineering, Beihang University, Beijing 100191 (China)

2015-03-15

Highlights: • Novel Ti{sub 47}Cu{sub 38}Zr{sub 7.5}Fe{sub 2.5}Sn{sub 2}Si{sub 1}Ag{sub 2} (at.%) bulk metallic glass (BMG) with a critical diameter of 7 mm was discovered. • The present BMG is the largest Ni- and Be-free Ti-based BMG containing low content of noble metal reported to date. • The glassy alloy possesses high specific strength, low Young’s modulus, and good corrosion resistance and bio-compatibility. • Combination of high glass-forming ability and good mechano- and bio-compatibility for the Ti-based BMG demonstrates the potential for use in biomedical applications. - Abstract: A novel Ni-free Ti{sub 47}Cu{sub 38}Zr{sub 7.5}Fe{sub 2.5}Sn{sub 2}Si{sub 1}Ag{sub 2} (at.%) bulk metallic glass (BMG) with superior glass-forming ability, good mechanical properties and excellent biocompatibility was discovered. The Ti-based BMG with a diameter of 7 mm can be prepared by copper mold casting and the supercooled liquid region was 52 K. Compressive strength, specific strength, Young’s modulus and microhardness of the Ti-based BMG were about 2.08 GPa, 3.2 × 10{sup 5} N m/kg, 100 GPa and 588 Hv, respectively. Electrochemical measurements indicated that the Ti-based glassy alloy possesses higher corrosion resistance than Ti–6Al–4V alloy in a simulated body fluid environment. Attachment, spreading out and proliferation of MC3T3-E1 cells on the Ti-based BMG surface demonstrated the excellent biocompatibility. Mechanisms of the formation and properties for the Ti-based glassy alloy are also discussed. The combination of high glass-forming ability, excellent mechanical properties, high corrosion resistance and good biocompatibility demonstrates the potential of the Ni-free Ti-based BMG for use in biomedical applications.

New Ti-based Ti–Cu–Zr–Fe–Sn–Si–Ag bulk metallic glass for biomedical applications

International Nuclear Information System (INIS)

Pang, Shujie; Liu, Ying; Li, Haifei; Sun, Lulu; Li, Yan; Zhang, Tao

2015-01-01

Highlights: • Novel Ti 47 Cu 38 Zr 7.5 Fe 2.5 Sn 2 Si 1 Ag 2 (at.%) bulk metallic glass (BMG) with a critical diameter of 7 mm was discovered. • The present BMG is the largest Ni- and Be-free Ti-based BMG containing low content of noble metal reported to date. • The glassy alloy possesses high specific strength, low Young’s modulus, and good corrosion resistance and bio-compatibility. • Combination of high glass-forming ability and good mechano- and bio-compatibility for the Ti-based BMG demonstrates the potential for use in biomedical applications. - Abstract: A novel Ni-free Ti 47 Cu 38 Zr 7.5 Fe 2.5 Sn 2 Si 1 Ag 2 (at.%) bulk metallic glass (BMG) with superior glass-forming ability, good mechanical properties and excellent biocompatibility was discovered. The Ti-based BMG with a diameter of 7 mm can be prepared by copper mold casting and the supercooled liquid region was 52 K. Compressive strength, specific strength, Young’s modulus and microhardness of the Ti-based BMG were about 2.08 GPa, 3.2 × 10 5 N m/kg, 100 GPa and 588 Hv, respectively. Electrochemical measurements indicated that the Ti-based glassy alloy possesses higher corrosion resistance than Ti–6Al–4V alloy in a simulated body fluid environment. Attachment, spreading out and proliferation of MC3T3-E1 cells on the Ti-based BMG surface demonstrated the excellent biocompatibility. Mechanisms of the formation and properties for the Ti-based glassy alloy are also discussed. The combination of high glass-forming ability, excellent mechanical properties, high corrosion resistance and good biocompatibility demonstrates the potential of the Ni-free Ti-based BMG for use in biomedical applications

PCB 126 toxicity is modulated by cross-talk between caveolae and Nrf2 signaling

Energy Technology Data Exchange (ETDEWEB)

Petriello, Michael C. [Graduate Center for Toxicology, College of Medicine, University of Kentucky, Lexington, KY 40536 (United States); University of Kentucky Superfund Research Center, Lexington, KY 40536 (United States); Han, Sung Gu [University of Kentucky Superfund Research Center, Lexington, KY 40536 (United States); Department of Food Science and Biotechnology of Animal Resources, College of Animal Bioscience and Technology, Konkuk University, Seoul 143-701 (Korea, Republic of); Newsome, Bradley J. [University of Kentucky Superfund Research Center, Lexington, KY 40536 (United States); Department of Chemistry, College of Arts and Sciences, University of Kentucky, Lexington, KY 40506 (United States); Hennig, Bernhard [Graduate Center for Toxicology, College of Medicine, University of Kentucky, Lexington, KY 40536 (United States); University of Kentucky Superfund Research Center, Lexington, KY 40536 (United States); Department of Animal and Food Sciences, College of Agriculture, Food and Environment, University of Kentucky, KY 40506 (United States)

2014-06-01

Environmental toxicants such as polychlorinated biphenyls (PCBs) have been implicated in the promotion of multiple inflammatory disorders including cardiovascular disease, but information regarding mechanisms of toxicity and cross-talk between relevant cell signaling pathways is lacking. To examine the hypothesis that cross-talk between membrane domains called caveolae and nuclear factor (erythroid-derived 2)-like 2 (Nrf2) pathways alters PCB-induced inflammation, caveolin-1 was silenced in vascular endothelial cells, resulting in a decreased PCB-induced inflammatory response. Cav-1 silencing (siRNA treatment) also increased levels of Nrf2-ARE transcriptional binding, resulting in higher mRNA levels of the antioxidant genes glutathione s-transferase and NADPH dehydrogenase quinone-1 in both vehicle and PCB-treated systems. Along with this upregulated antioxidant response, Cav-1 siRNA treated cells exhibited decreased mRNA levels of the Nrf2 inhibitory protein Keap1 in both vehicle and PCB-treated samples. Silencing Cav-1 also decreased protein levels of Nrf2 inhibitory proteins Keap1 and Fyn kinase, especially in PCB-treated cells. Further, endothelial cells from wildtype and Cav-1 −/− mice were isolated and treated with PCB to better elucidate the role of functional caveolae in PCB-induced endothelial inflammation. Cav-1 −/− endothelial cells were protected from PCB-induced cellular dysfunction as evidenced by decreased vascular cell adhesion molecule (VCAM-1) protein induction. Compared to wildtype cells, Cav-1 −/− endothelial cells also allowed for a more effective antioxidant response, as observed by higher levels of the antioxidant genes. These data demonstrate novel cross-talk mechanisms between Cav-1 and Nrf2 and implicate the reduction of Cav-1 as a protective mechanism for PCB-induced cellular dysfunction and inflammation. - Highlights: • Reduction of caveolin-1 protein protects against polychlorinated biphenyl toxicity. • Decreasing

Existence conditions for bulk large-wavevector waves in metal-dielectric and graphene-dielectric multilayer hyperbolic metamaterials

DEFF Research Database (Denmark)

Zhukovsky, Sergei; Andryieuski, Andrei; Lavrinenko, Andrei

2014-01-01

We theoretically investigate general existence conditions for broadband bulk large-wavevector (high-k) propagating waves (such as volume plasmon polaritons in hyperbolic metamaterials) in arbitrary subwavelength periodic multilayers structures. Treating the elementary excitation in the unit cell...... of the structure as a generalized resonance pole of reflection coefficient and using Bloch's theorem, we derive analytical expressions for the band of large-wavevector propagating solutions. We apply our formalism to determine the high-k band existence in two important cases: the well-known metal-dielectric...

Contrasting PCB bioaccumulation patterns among Lake Huron lake trout reflect basin-specific ecology.

Science.gov (United States)

Paterson, Gordon; Ryder, Mark; Drouillard, Ken G; Haffner, G Douglas

2016-01-01

This study collected multiple age classes of lake trout from Lake Huron's Main Basin, Georgian Bay, and North Channel regions to compare and contrast top predator polychlorinated biphenyl (PCB) bioaccumulation patterns in separate compartments of the same ecosystem. Sum PCB concentrations were highest for Main Basin (260 ± 24.9 ng g(-1) wet wt) fish, followed by Georgian Bay (74.6 ± 16.2 ng g(-1) ) and North Channel (42.0 ± 3.3 ng g(-1)) fish. Discriminant functions analysis of lake trout PCB profiles and stable carbon (δ(13)C) and nitrogen (δ(15)N) isotope values clearly distinguished fish by location, indicating high degrees of basin fidelity throughout their lifetimes in addition to highly contrasting PCB bioaccumulation profiles. These unique profiles were not attributable to significant differences in lake trout lipid contents (p = 0.856) or trophic position (δ(15)N; p = 0.334), with rainbow smelt representing the primary prey across the basins. Furthermore, significant differences were observed among the basins for the relationships between PCB biomagnification factors and hydrophobicity. An empirical model for predicting PCB biomagnification in Lake Huron lake trout indicated that basin-specific population growth rates and prey abundances were significant for explaining these contrasting patterns of PCB bioaccumulation. The results of the present study are fundamental for understanding the role of ecology in legacy persistent organic pollutant (POP) bioaccumulation. Specifically, ecosystem characteristics such as prey abundances, foraging ecology, and ultimately consumer growth can regulate the variability of legacy POP bioaccumulation as observed within and among a wide range of freshwater ecosystems. © 2015 SETAC.

2,2′,3,5′,6-PENTACHLOROBIPHENYL (PCB 95) AND ITS HYDROXYLATED METABOLITES ARE ENANTIOMERICALLY ENRICHED IN FEMALE MICE

Science.gov (United States)

Kania-Korwel, Izabela; Barnhart, Christopher D.; Stamou, Marianna; Truong, Kim M.; El-Komy, Mohammed H.M.E.; Lein, Pamela J.; Veng-Pedersen, Peter; Lehmler, Hans-Joachim

2012-01-01

Epidemiological and laboratory studies link polychlorinated biphenyls and their metabolites to adverse neurodevelopmental outcomes. Several neurotoxic PCB congeners are chiral and undergo enantiomeric enrichment in mammalian species, which may modulate PCB developmental neurotoxicity. This study measures levels and enantiomeric enrichment of PCB 95 and its hydroxylated metabolites (OH-PCBs) in adult female C57Bl/6 mice following subchronic exposure to racemic PCB 95. Tissue levels of PCB 95 and OH-PCBs increased with increasing dose. Dose-dependent enantiomeric enrichment of PCB 95 was observed in brain and other tissues. OH-PCBs also displayed enantiomeric enrichment in blood and liver, but were not detected in adipose and brain. In light of data suggesting enantioselective effects of chiral PCBs on molecular targets linked to PCB developmental neurotoxicity, our observations highlight the importance of accounting for PCB and OH-PCB enantiomeric enrichment in the assessment of PCB developmental neurotoxicity. PMID:22974126

PCB congener concentrations in a municipal sewer system in New Jersey, USA

Energy Technology Data Exchange (ETDEWEB)

Loganathan, B. [Murray State Univ., Murray, KY (United States); Botts, J.A. [Aquatic Sciences Consulting, Woodbine, MD (United States); Spadone, J.; McKenna, B. [Linden Roselle Sewerage Authority, Linden, NJ (United States); Sajwan, K.S. [Savannah State Univ., Savannah, GA (United States)

2005-07-01

This paper provided details of a water sampling pilot study conducted in the Linden Roselle Sewerage Authority (LRSA) region in New Jersey. The pilot study was conducted as part of a polychlorinated biphenyl (PCB) monitoring program. Total PCB concentrations in whole water samples in both dissolved and particulate phases were collected at selected locations in the LRSA. PCB loading estimates for dry weather were also provided. Automatic composite sampler equipped with peristaltic pump mechanisms were used to collect the samples in a series of 4 rounds. Sample extracts were then purified and analyzed using a gas chromatograph electron capture detector (GC-ECD). Results showed that in dry weather, total PCBs were between 2.6 to 6.0-fold higher in the western sampling area than in the Roselle Flue, which received sewage flows from residential and commercial sources in the northwest area of the LRSA. Wet weather samples showed only slightly higher total PCBs. Data indicated a source of PCBs in the western portion of the sewershed. In dry weather, higher PCB levels were found in the whole primary influent samples. It was concluded that increased PCB levels were attributed to grit and sludge processing waste streams within a waste water treatment plant. 8 refs., 2 tabs.

Simultaneous decontamination of cross-polluted soils with heavy metals and PCBs using a nano-metallic Ca/CaO dispersion mixture.

Science.gov (United States)

Mallampati, Srinivasa Reddy; Mitoma, Yoshiharu; Okuda, Tetsuji; Sakita, Shogo; Simion, Cristian

2014-01-01

In the present work, we investigated the use of nano-metallic calcium (Ca) and calcium oxide (CaO) dispersion mixture for the simultaneous remediation of contaminated soils with both heavy metals (As, Cd, Cr, and Pb) and polychlorinated biphenyls (PCBs). Regardless of soil moisture content, nano-metallic Ca/CaO dispersion mixture achieved about 95-99% of heavy metal immobilization by a simple grinding process. During the same treatment, reasonable PCB hydrodechlorination efficiencies were obtained (up to 97%), though higher hydrodechlorination efficiency by preliminary drying of soil was observed.

Linear magnetoresistance and surface to bulk coupling in topological insulator thin films.

Science.gov (United States)

Singh, Sourabh; Gopal, R K; Sarkar, Jit; Pandey, Atul; Patel, Bhavesh G; Mitra, Chiranjib

2017-12-20

We explore the temperature dependent magnetoresistance of bulk insulating topological insulator thin films. Thin films of Bi 2 Se 2 Te and BiSbTeSe 1.6 were grown using the pulsed laser deposition technique and subjected to transport measurements. Magnetotransport measurements indicate a non-saturating linear magnetoresistance (LMR) behavior at high magnetic field values. We present a careful analysis to explain the origin of LMR taking into consideration all the existing models of LMR. Here we consider that the bulk insulating states and the metallic surface states constitute two parallel conduction channels. Invoking this, we were able to explain linear magnetoresistance behavior as a competition between these parallel channels. We observe that the cross-over field, where LMR sets in, decreases with increasing temperature. We propose that this cross-over field can be used phenomenologically to estimate the strength of surface to bulk coupling.

Effect of shock pressure on the structure and superconducting properties of Y-Ba-Cu-O in explosively fabricated bulk metal-matrix composites

Science.gov (United States)

Murr, L. E.; Niou, C. S.; Pradhan-Advani, M.

1991-01-01

While it is now well established that copper-oxide-based power, or virtually any other ceramic superconductor powder, can be consolidated and encapsulated within a metal matrix by explosive consolidation, the erratic superconductivity following fabrication has posed a major problem for bulk applications. The nature of this behavior was found to arise from microstructural damage created in the shock wave front, and the residual degradation in superconductivity was demonstrated to be directly related to the peak shock pressure. The explosively fabricated or shock loaded YBa2Cu3Ox examples exhibit drastically altered rho (or R) - T curves. The deterioration in superconductivity is even more noticeable in the measurement of ac magnetic susceptibility and flux exclusion or shielding fraction which is also reduced in proportion to increasing peak shock pressure. The high frequency surface resistance (in the GHz range) is also correspondingly compromised in explosively fabricated, bulk metal-matrix composites based on YBa2Cu3O7. Transmission electron microscopy (including lattice imaging techniques) is being applied in an effort to elucidate the fundamental (microstructural) nature of the shock-induced degradation of superconductivity and normal state conductivity. One focus of TEM observations has assumed that oxygen displaced from b-chains rather than oxygen-vacancy disorder in the basal plane of oxygen deficient YBa2Cu3Ox may be a prime mechanism. Shock-wave displaced oxygen may also be locked into new positions or interstitial clusters or chemically bound to displaced metal (possibly copper) atoms to form precipitates, or such displacements may cause the equivalent of local lattice cell changes as a result of stoichiometric changes. While the shock-induced suppression of T(sub c) is not desirable in the explosive fabrication of bulk metal-matrix superconductors, it may be turned into an advantage if the atomic-scale distortion can be understood and controlled as local

Prenatal and postnatal serum PCB concentrations and cochlear function in children at 45 months of age.

Science.gov (United States)

Jusko, Todd A; Sisto, Renata; Iosif, Ana-Maria; Moleti, Arturo; Wimmerová, Sonˇa; Lancz, Kinga; Tihányi, Juraj; Sovčiková, Eva; Drobná, Beata; Palkovičová, L'ubica; Jurečková, Dana; Thevenet-Morrison, Kelly; Verner, Marc-André; Sonneborn, Dean; Hertz-Picciotto, Irva; Trnovec, Tomáš

2014-11-01

Some experimental and human data suggest that exposure to polychlorinated biphenyls (PCBs) may induce ototoxicity, though results of previous epidemiologic studies are mixed and generally focus on either prenatal or postnatal PCB concentrations exclusively. Our aim was to evaluate the association between pre- and postnatal PCB concentrations in relation to cochlear status, assessed by distortion product otoacoustic emissions (DPOAEs), and to further clarify the critical periods in development where cochlear status may be most susceptible to PCBs. A total of 351 children from a birth cohort in eastern Slovakia underwent otoacoustic testing at 45 months of age. Maternal pregnancy, cord, and child 6-, 16-, and 45-month blood samples were collected and analyzed for PCB concentrations. At 45 months of age, DPOAEs were assessed at 11 frequencies in both ears. Multivariate, generalized linear models were used to estimate the associations between PCB concentrations at different ages and DPOAEs, adjusting for potential confounders. Maternal and cord PCB-153 concentrations were not associated with DPOAEs at 45 months. Higher postnatal PCB concentrations at 6-, 16-, and 45-months of age were associated with lower (poorer) DPOAE amplitudes. When all postnatal PCB exposures were considered as an area-under-the-curve metric, an increase in PCB-153 concentration from the 25th to the 75th percentile was associated with a 1.6-dB SPL (sound pressure level) decrease in DPOAE amplitude (95% CI: -2.6, -0.5; p = 0.003). In this study, postnatal rather than maternal or cord PCB concentrations were associated with poorer performance on otoacoustic tests at age 45 months.

Current data on the background burden to the persistent organochlorine pollutants HCB, p,p'-DDE as well as PCB 138, PCB 153 and PCB 180 in plasma of the general population in Germany.

Science.gov (United States)

Schettgen, Thomas; Alt, Anne; Esser, Andre; Kraus, Thomas

2015-06-01

Despite their long-term ban, persistent organochlorine compounds like hexachlorobenzene (HCB), p,p'-dichlorodiphenylethylene (DDE) as well as polychlorinated biphenyls (PCBs) are still of environmental concern. For the evaluation of potential occupational or environmental exposures to these substances, it is essential to know the current background burden of the general population. As representative and up-to-date information is missing for Germany, we have analysed a large dataset generated in studies on potential exposure to lower chlorinated PCBs to fill this gap for the levels of HCB, DDE as well as PCB 138, PCB 153 and PCB 180. We have investigated n=2750 plasma samples of persons of the general population living in North Rhine-Westfalia and Hesse aged 6-65 years and sampled between September 2010 and March 2014. For evaluation of the age-dependent accumulation in the general population we have generated seven age groups in the collective. Our laboratory used a validated and quality controlled procedure using GC/MS for quantification of the organochlorine compounds in plasma (LOQ: 0.01μg/L). The median (95th percentile) levels for ∑ PCB 138+PCB 153+PCB 180 were 0.14 (0.73); 0.30 (0.82); 0.38 (0.88); 0.50 (1.14); 0.92; 1.58 (3.54) and 2.41 (4.82)μg/L plasma in the age groups 6-10 years (n=102), 11-17 years (n=499), 18-25 years (n=157), 26-35 years (n=710), 36-45 years (n=400), 46-55 years (n=525) and 56-65 years (n=357), respectively. Similarly, the median (95th percentile) levels of p,p'-DDE were 0.18 (1.24); 0.18 (0.74); 0.24 (0.85); 0.30 (1.20); 0.45 (1.74); 0.64 (3.25) and 0.94 (4.7)μg/L plasma. Finally, the median (95th percentile) of HCB in plasma in these age groups was 0.05 (0.10); 0.06 (0.11); 0.08 (0.15); 0.08 (0.15); 0.11 (0.22); 0.14 (0.42) and 0.20 (0.68)μg/L plasma. Our results prove an overall substantial reduction in the body burden to organochlorine compounds in Germany compared to earlier studies. However, 15% and 3.6% of the examined

PCB Embedded Inductor for High-Frequency ZVS SEPIC Converter

DEFF Research Database (Denmark)

Dou, Yi; Ouyang, Ziwei; Thummala, Prasanth

2018-01-01

The volume and temperature rise of passive components, especially inductors, limit the momentum toward high power density in high-frequency power converters. To address the limitations, PCB integration of passive components should be considered with the benefit of low profile, excellent thermal...... characteristic and cost reduction. This paper investigates an embedded structure of inductors to further increase the power density of a low power DC-DC converter. A pair of coupling inductors have been embedded into the PCB. The detailed embedded process has been described and the characteristics of embedded...

The effect of nanocrystallization and free volume on the room temperature plasticity of Zr-based bulk metallic glasses

International Nuclear Information System (INIS)

Mondal, K.; Ohkubo, T.; Toyama, T.; Nagai, Y.; Hasegawa, M.; Hono, K.

2008-01-01

To understand the mechanism of the room temperature plasticity of bulk metallic glasses (BMGs), microstructure observations, density measurements and positron annihilation studies were carried out for Zr-based BMGs cast at various temperatures and post-annealed under different conditions. We found that higher casting temperatures cause partial crystallization, which enhance the plasticity as long as the volume fraction of the crystalline phase is low. However, a similar nanocrystalline microstructure produced by post-annealing often leads to a large loss of plasticity, while certain conditions enhance the plasticity. Based on density measurements and positron annihilation lifetime spectroscopy, we conclude that the relative contribution of free volume and nanocrystallization is important for acquiring plasticity in metallic glasses

Non-hydrolytic metal oxide films for perovskite halide overcoating and stabilization

Science.gov (United States)

Martinson, Alex B.; Kim, In Soo

2017-09-26

A method of protecting a perovskite halide film from moisture and temperature includes positioning the perovskite halide film in a chamber. The chamber is maintained at a temperature of less than 200 degrees Celsius. An organo-metal compound is inserted into the chamber. A non-hydrolytic oxygen source is subsequently inserted into the chamber. The inserting of the organo-metal compound and subsequent inserting of the non-hydrolytic oxygen source into the chamber is repeated for a predetermined number of cycles. The non-hydrolytic oxygen source and the organo-metal compound interact in the chamber to deposit a non-hydrolytic metal oxide film on perovskite halide film. The non-hydrolytic metal oxide film protects the perovskite halide film from relative humidity of greater than 35% and a temperature of greater than 150 degrees Celsius, respectively.

Chronic treatment with polychlorinated biphenyls (PCB) during pregnancy and lactation in the rat

International Nuclear Information System (INIS)

Cocchi, Daniela; Tulipano, Giovanni; Colciago, Alessandra; Sibilia, Valeria; Pagani, Francesca; Vigano, Daniela; Rubino, Tiziana; Parolaro, Daniela; Bonfanti, Patrizia; Colombo, Anita; Celotti, Fabio

2009-01-01

Polychlorinated biphenyls (PCBs) are pollutants detected in animal tissues and breast milk. The experiments described in the present paper were aimed at evaluating whether the four PCB congeners most abundant in animal tissues (PCB-138, -153, -180 and -126), administered since fetal life till weaning, can induce long-term alterations of GH-axis activity and bone mass in the adult rat. We measured PCB accumulation in rat brain and liver, somatic growth, pituitary GH expression and plasma hormone concentrations at different ages. Finally, we studied hypothalamic somatostatin expression and bone structure in adulthood, following long-term PCB exposure. Dams were treated during pregnancy from GD15 to GD19 and during breast-feeding. A constant reduction of the growth rate in both male and female offspring from weaning to adulthood was observed in exposed animals. Long-lasting alterations on hypothalamic-pituitary GH axis were indeed observed in PCB-exposed rats in adulthood: increased somatostatin expression in hypothalamic periventricular nucleus (both males and females) and lateral arcuate nucleus (males, only) and decreased GH mRNA levels in the pituitary of male rats. Plasma IGF-1 levels were higher in PCB-exposed male and female animals as compared with controls at weaning and tended to be higher at PN60. Plasma testosterone and thyroid hormone concentrations were not significantly affected by exposure to PCBs. In adulthood, PCBs caused a significant reduction of bone mineral content and cortical bone thickness of tibiae in male rat joint to increased width of the epiphyseal cartilage disk. In conclusion, the developmental exposure to the four selected PCB compounds used in the present study induced far-reaching effects in the adult offspring, the male rats appearing more sensitive than females.

Heavy metal extraction from PCB wastewater treatment sludge by sulfuric acid

International Nuclear Information System (INIS)

Kuan, Yu-Chung; Lee, I-Hsien; Chern, Jia-Ming

2010-01-01

Heavy metals contaminated wastewater sludge is classified as hazardous solid waste and needs to be properly treated to prevent releasing heavy metals to the environment. In this study, the wastewater treatment sludge from a printed circuit board manufacturing plant was treated in a batch reactor by sulfuric acid to remove the contained heavy metals. The effects of sulfuric acid concentration and solid to liquid ratio on the heavy metal removal efficiencies were investigated. The experimental results showed that the total and individual heavy metal removal efficiencies increased with increasing sulfuric acid concentration, but decreased with increasing solid to liquid ratio. A mathematical model was developed to predict the residual sludge weights at varying sulfuric concentrations and solid to liquid ratios. The trivalent heavy metal ions, iron and chromium were more difficult to be removed than the divalent ions, copper, zinc, nickel, and cadmium. For 5 g/L solid to liquid ratio, more than 99.9% of heavy metals can be removed from the sludge by treating with 0.5 M sulfuric acid in 2 h.

A combined arc-melting and tilt-casting furnace for the manufacture of high-purity bulk metallic glass materials.

Science.gov (United States)

Soinila, E; Pihlajamäki, T; Bossuyt, S; Hänninen, H

2011-07-01

An arc-melting furnace which includes a tilt-casting facility was designed and built, for the purpose of producing bulk metallic glass specimens. Tilt-casting was chosen because reportedly, in combination with high-purity processing, it produces the best fatigue endurance in Zr-based bulk metallic glasses. Incorporating the alloying and casting facilities in a single piece of equipment reduces the amount of laboratory space and capital investment needed. Eliminating the sample transfer step from the production process also saves time and reduces sample contamination. This is important because the glass forming ability in many alloy systems, such as Zr-based glass-forming alloys, deteriorates rapidly with increasing oxygen content of the specimen. The challenge was to create a versatile instrument, in which high purity conditions can be maintained throughout the process, even when melting alloys with high affinity for oxygen. Therefore, the design provides a high-vacuum chamber to be filled with a low-oxygen inert atmosphere, and takes special care to keep the system hermetically sealed throughout the process. In particular, movements of the arc-melting electrode and sample manipulator arm are accommodated by deformable metal bellows, rather than sliding O-ring seals, and the whole furnace is tilted for tilt-casting. This performance of the furnace is demonstrated by alloying and casting Zr(55)Cu(30)Al(10)Ni(5) directly into rods up to ø 10 mm which are verified to be amorphous by x-ray diffraction and differential scanning calorimetry, and to exhibit locally ductile fracture at liquid nitrogen temperature.

Early weaning PCB 95 exposure alters the neonatal endocrine system: thyroid adipokine dysfunction.

Science.gov (United States)

Ahmed, R G

2013-12-01

Polychlorinated biphenyls (PCBs) are persistent environmental pollutants that can severely disrupt the endocrine system. In the present study, early-weaned male rats were administered a single dose of 2,3,6-2',5'-pentachlorinated biphenyl (PCB 95; 32 mg/kg per day, by i.p. injection) for two consecutive days (postnatal days (PNDs) 15 and 16) and killed 24 and 48 h after the administration of the last dose. Compared with the control group, administration of PCB 95 induced a reduction (Pcolloidal contents at PND 18. The dyshormonogenesis and thyroid dysgenesis may be attributed to the elevation of DNA fragmentation at PNDs 17 and 18. Furthermore, this hypothyroid state revealed higher (Pinsulin at both PNDs compared with the control group. Interestingly, the body weight of the neonates in the PCB 95 group exhibited severe decreases throughout the experimental period in relation to that of the control group. These results imply that PCB 95 may act as a disruptor of the developmental hypothalamic-pituitary-thyroid axis. Hypothyroidism caused by PCB 95 may impair the adipokine axis, fat metabolism, and in general postnatal development. Thus, further studies need to be carried out to understand this concept.

Atropisomers of 2,2',3,3',6,6'-hexachlorobiphenyl (PCB 136) exhibit stereoselective effects on activation of nuclear receptors in vitro.

Science.gov (United States)

Pěnčíková, Kateřina; Brenerová, Petra; Svržková, Lucie; Hrubá, Eva; Pálková, Lenka; Vondráček, Jan; Lehmler, Hans-Joachim; Machala, Miroslav

2017-11-09

PCB 136 is an environmentally relevant chiral PCB congener, which has been found in vivo to be present in form of rotational isomers (atropisomers). Its atropselective biotransformation or neurotoxic effects linked with sensitization of ryanodine receptor suggest that it might interact also with other intracellular receptors in a stereospecific manner. However, possible atropselective effects of PCB 136 on nuclear receptor transactivation remain unknown. Therefore, in this study, atropselective effects of PCB 136 on nuclear receptors controlling endocrine signaling and/or expression of xenobiotic and steroid hormone catabolism were investigated. PCB136 atropisomers were found to exert differential effects on estrogen receptor (ER) activation; (+)-PCB 136 was estrogenic, while (-)-PCB 136 was antiestrogenic. In contrast, inhibition of androgen receptor (AR) activity was not stereospecific. Both PCB136 stereoisomers induced the constitutive androgen receptor (CAR)-dependent gene expression; however, no significant stereospecificity of PCB 136 atropisomers was observed. PCB136 was a partial inducer of the pregnane X receptor (PXR)-dependent gene expression. Here, (-)-PCB 136 was a significantly more potent inducer of PXR activity than (+)-PCB 136. Taken together, the present results indicate that at least two nuclear receptors participating in endocrine regulation or metabolism, ER and PXR, could be regulated in an atropselective manner by chiral PCB 136. The enantioselective enrichment of PCB atropisomers in animal and human tissues may thus have significant consequences for endocrine-disrupting effects of chiral ortho-substituted PCB congeners.

Modelling of non-metallic particles motion process in foundry alloys

Directory of Open Access Journals (Sweden)

P. L. Żak

2015-04-01

Full Text Available The behaviour of non-metallic particles in the selected composites was analysed, in the current study. The calculations of particles floating in liquids differing in viscosity were performed. Simulations based on the Stokes equation were made for spherical SiC particles and additionally the particle size influence on Reynolds number was analysed.The movement of the particles in the liquid metal matrix is strictly connected with the agglomerate formation problem.Some of collisions between non-metallic particles lead to a permanent connection between them. Creation of the two spherical particles and a metallic phase system generates the adhesion force. It was found that the adhesion force mainly depends on the surface tension of the liquid alloy and radius of non-metallic particles.

Computerization of the Electronic Scheme Drawing Equipment on Printed-Circuit-Board (PCB) Surface (Phase One)

International Nuclear Information System (INIS)

Abdul Hafid; Pinitoyo, A.; Demon H; Kussigit S; Paidjo; Riswan Dj; Natsir, M.; Dedy H; Edy Karyanta; Edy S

2003-01-01

To increase the capability of the PCB immersion machine developed previous a computerized drawing machine on PCB surface is proposed for drawing the schematic electronic, PROTEL software is used Used is Roland DXY 1100 type which had been modified to accommodate the PCB characteristic, because it is used originally for paper. Concerning, the plotter ink, the waterproof type must be used. (author)

PCB Concentrations and Dioxin-like Activity in Blood Samples from Danish School Children and Their Mothers living in Urban and Rural Areas

DEFF Research Database (Denmark)

Mørck, Thit A; Erdmann, Simon E; Long, Manhai

2014-01-01

Human exposure to persistent organic pollutants (POPs) is of major concern due to a diversity of adverse effects from prolonged exposure and bioaccumulation. Manufacturing of polychlorinated biphenyls (PCBs), a subgroup of POPs, has been prohibited for many decades; however, human exposure still...... occurs due to the persistent nature of the chemicals. The concentrations of the dioxin-like PCB congeners 105, 118 and 156 and the non-dioxin-like PCB congeners 28, 52, 101, 138, 153 and 180, p,p'-DDE, p,p'-DDT, o,p'-DDE, o,p'-DDT, HCB and β-HCH as well as the dioxin-like activity using the Ah......R transactivity assay were analysed in blood samples from Danish schoolchildren and their mothers in the European framework of the DEMOCOPHES/COPHES projects. The participants were selected from an urban and a rural area, respectively. The PCB concentrations and the AhR-TEQ (TCDD toxic equivalent) were...

Dietary Selenium as a Modulator of PCB 126–Induced Hepatotoxicity in Male Sprague-Dawley Rats

Science.gov (United States)

Lai, Ian K.; Chai, Yingtao; Simmons, Donald; Watson, Walter H.; Tan, Rommel; Haschek, Wanda M.; Wang, Kai; Wang, Bingxuan; Ludewig, Gabriele; Robertson, Larry W.

2011-01-01

Homeostasis of selenium (Se), a critical antioxidant incorporated into amino acids and enzymes, is disrupted by exposure to aryl hydrocarbon receptor (AhR) agonists. Here we examined the importance of dietary Se in preventing the toxicity of the most toxic polychlorinated biphenyl congener, 3,3′,4,4′,5-pentachlorobiphenyl (PCB 126), a potent AhR agonist. Male Sprague-Dawley rats were fed a modified AIN-93 diet with differing dietary Se levels (0.02, 0.2, and 2 ppm). Following 3 weeks of acclimatization, rats from each dietary group were given a single ip injection of corn oil (vehicle), 0.2, 1, or 5 μmol/kg body weight PCB 126, followed 2 weeks later by euthanasia. PCB exposure caused dose-dependent increases in liver weight and at the highest PCB 126 dose decreases in whole body weight gains. Hepatic cytochrome P-450 (CYP1A1) activity was significantly increased even at the lowest dose of PCB 126, indicating potent AhR activation. PCB exposure diminished hepatic Se levels in a dose-dependent manner, and this was accompanied by diminished Se-dependent glutathione peroxidase activity. Both these effects were partially mitigated by Se supplementation. Conversely, thioredoxin (Trx) reductase activity and Trx oxidation state, although significantly diminished in the lowest dietary Se groups, were not affected by PCB exposure. In addition, PCB 126–induced changes in hepatic copper, iron, manganese, and zinc were observed. These results demonstrate that supplemental dietary Se was not able to completely prevent the toxicity caused by PCB 126 but was able to increase moderately the levels of several key antioxidants, thereby maintaining them roughly at normal levels. PMID:21865291

PCB and Dioxin content of Swedish waste fuels; PCB- och dioxininnehaall i svenska avfallsbraenslen

Energy Technology Data Exchange (ETDEWEB)

Blomqvist, Evalena (Swedish National Testing and Research Inst., Boraas (Sweden)) (and others)

2009-06-15

Reported dioxin data in the literature presents a rather large variation, 1-255 ng I-TEQ/kg, among different municipal solid waste (MSW) mixture samples taken within different countries. However the variation is not only large between different countries, a significant variation is reported within each study as well. Results that shows the importance of using reliable and representative sampling methods. The majority of the reported dioxin levels is within 4 to 45 ng I-TEQ/kg waste. In some of the reported studies the dioxin content has as well been analysed in sources-sorted fractions. The majority, 90-95%, of the detected dioxins were found in the fraction consisting of textiles and leather. This study aims to analyse the amount and variations, of the toxic dioxin and PCB congeners within a typical MSW mixture in Sweden, before it is energy recovered in a waste incineration plant. The study includes 20 samples, taken from two different plants in Sweden i.e. Renova and Boraas Energi och Miljoe, during 2007/2008. A well evaluated sampling method were used at both plants to achieve representative samples. Each sampling campaign resulted in a 30 kg sample that was transported in sealed containers to a laboratory. The heat value and a complete determination of the elementary content was analysed as well as the levels of toxic dioxins and PCBs in all samples. All results, both organic and inorganic, were rather similar between the two incineration plants. The resemblance within the results is an outcome of that good and representative sampling method has been used during the sampling campaigns. The average value (+/- standard deviation) of all 20 samples is 29 +/-15 ng I-TEQ per kilo of dry MSW. An average value which is within the lower range of the previous reported levels in the literature. The lower dioxin content within Swedish MSW mixtures is most likely due to the relative well-controlled waste management and sorting system in Sweden. The majority of the

Polychlorinated Biphenyl Sources, Emissions, and Environmental Levels in school Buildings (PCB Workshop presentation)

Science.gov (United States)

Measure PCB emission rates from primary sources in laboratory chambersMeasure transport and sorption by materials and dust in laboratory chambersCharacterize PCBs in school building materialsEstimate PCB emission rates from sources in schoolsExamine congener patterns in sources a...

Fine Coining of Bulk Metal Formed Parts in Digital Environment

International Nuclear Information System (INIS)

Pepelnjak, T.; Kuzman, K.; Krusic, V.

2007-01-01

At present the production of bulk metal formed parts in the automotive industry must increasingly fulfil demands for narrow tolerance fields. The final goal of the million parts production series is oriented towards zero defect production. This is possible by achieving production tolerances which are even tighter than the prescribed ones. Different approaches are used to meet this demanding objective affected by many process parameters. Fine coining as a final forming operation is one of the processes which enables the production of good manufacturing tolerances and high process stability. The paper presents the analyses of the production of the inner race and a digital evaluation of manufacturing tolerances caused by different material parameters of the workpiece. Digital optimisation of the fine coining with FEM simulations was performed in two phases. Firstly, fine coining of the inner racer in a digital environment was comparatively analysed with the experimental work in order to verify the accuracy and reliability of digitally calculated data. Secondly, based on the geometrical data of a digitally fine coined part, tool redesign was proposed in order to tighten production tolerances and increase the process stability of the near-net-shaped cold formed part

Hepatic metabolism affects the atropselective disposition of 2,2',3,3',6,6'-hexachlorobiphenyl (PCB 136) in mice.

Science.gov (United States)

Wu, Xianai; Barnhart, Christopher; Lein, Pamela J; Lehmler, Hans-Joachim

2015-01-06

To understand the role of hepatic vs extrahepatic metabolism in the disposition of chiral PCBs, we studied the disposition of 2,2',3,3',6,6'-hexachlorobiphenyl (PCB 136) and its hydroxylated metabolites (HO-PCBs) in mice with defective hepatic metabolism due to the liver-specific deletion of cytochrome P450 oxidoreductase (KO mice). Female KO and congenic wild type (WT) mice were treated with racemic PCB 136, and levels and chiral signatures of PCB 136 and HO-PCBs were determined in tissues and excreta 3 days after PCB administration. PCB 136 tissue levels were higher in KO compared to WT mice. Feces was a major route of PCB metabolite excretion, with 2,2',3,3',6,6'-hexachlorobiphenyl-5-ol being the major metabolite recovered from feces. (+)-PCB 136, the second eluting PCB 136 atropisomers, was enriched in all tissues and excreta. The second eluting atropisomers of the HO-PCBs metabolites were enriched in blood and liver; 2,2',3,3',6,6'-hexachlorobiphenyl-5-ol in blood was an exception and displayed an enrichment of the first eluting atropisomers. Fecal HO-PCB levels and chiral signatures changed with time and differed between KO and WT mice, with larger HO-PCB enantiomeric fractions in WT compared to KO mice. Our results demonstrate that hepatic and, possibly, extrahepatic cytochrome P450 (P450) enzymes play a role in the disposition of PCBs.

Long-term effects of environmentally relevant doses of 2,2',4,4',5,5' hexachlorobiphenyl (PCB153 on neurobehavioural development, health and spontaneous behaviour in maternally exposed mice

Directory of Open Access Journals (Sweden)

Heegaard Einar

2011-01-01

Full Text Available Abstract Background Polychlorinated biphenyls (PCBs are widespread in the environment, human food and breast milk. Seafood is known to contain nutrients beneficial for the normal development and function of the brain, but also contaminants such as PCBs which are neurotoxic. Exposure to non-coplanar PCBs during brain development can disrupt spontaneous behaviour in mice and lead to hyperactive behaviour. Humans are chronically exposed to the highest relative levels of organochlorines in early childhood during brain development, though usually at doses which do not give clinical symptoms of toxicity. This study aimed to elucidate the developmental and behavioural effects of 2,2',4,4',5,5' hexachlorobiphenyl (PCB153 in mice, mimicking human exposure during gestation and lactation. Methods Environmentally relevant doses of PCB153 were added to the experimental diets. Feed concentrations were approximately 0.5, 6.5, and 1500 μg PCB153/kg feed, representing a realistic and a worst case scenario of frequent consumption of contaminated fish. The study also investigated the effects of maternal nutrition, i.e. a standard rodent diet versus a high inclusion of salmon. Mice pups were examined for physical- and reflex development, sensorimotor function and spontaneous behaviour from five days after birth until weaning. A selection of pups were followed until 16 weeks of age and tested for open field behaviour and the acoustic startle response (ASR with prepulse inhibition (PPI. Blood thyroid hormones and liver enzymes, blood lipids and PCB153 content in fat were examined at 16 weeks. Statistical analyses modelled the three way interactions of diet, PCB exposure and litter size on behaviour, using generalized linear models (GLM and linear mixed effect models (LME. The litter was used as a random variable. Non-parametric tests were used for pair wise comparisons of biochemical analyses. Results Litter size consistently influenced pup development and behaviour

Long-term effects of environmentally relevant doses of 2,2',4,4',5,5' hexachlorobiphenyl (PCB153) on neurobehavioural development, health and spontaneous behaviour in maternally exposed mice.

Science.gov (United States)

Haave, Marte; Bernhard, Annette; Jellestad, Finn K; Heegaard, Einar; Brattelid, Trond; Lundebye, Anne-Katrine

2011-01-13

Polychlorinated biphenyls (PCBs) are widespread in the environment, human food and breast milk. Seafood is known to contain nutrients beneficial for the normal development and function of the brain, but also contaminants such as PCBs which are neurotoxic. Exposure to non-coplanar PCBs during brain development can disrupt spontaneous behaviour in mice and lead to hyperactive behaviour. Humans are chronically exposed to the highest relative levels of organochlorines in early childhood during brain development, though usually at doses which do not give clinical symptoms of toxicity. This study aimed to elucidate the developmental and behavioural effects of 2,2',4,4',5,5' hexachlorobiphenyl (PCB153) in mice, mimicking human exposure during gestation and lactation. Environmentally relevant doses of PCB153 were added to the experimental diets. Feed concentrations were approximately 0.5, 6.5, and 1500 μg PCB153/kg feed, representing a realistic and a worst case scenario of frequent consumption of contaminated fish. The study also investigated the effects of maternal nutrition, i.e. a standard rodent diet versus a high inclusion of salmon. Mice pups were examined for physical- and reflex development, sensorimotor function and spontaneous behaviour from five days after birth until weaning. A selection of pups were followed until 16 weeks of age and tested for open field behaviour and the acoustic startle response (ASR) with prepulse inhibition (PPI). Blood thyroid hormones and liver enzymes, blood lipids and PCB153 content in fat were examined at 16 weeks. Statistical analyses modelled the three way interactions of diet, PCB exposure and litter size on behaviour, using generalized linear models (GLM) and linear mixed effect models (LME). The litter was used as a random variable. Non-parametric tests were used for pair wise comparisons of biochemical analyses. Litter size consistently influenced pup development and behaviour. Few lasting PCB153 related changes were observed

Idaho National Laboratory PCB Annual Document Log and Annual Records Report for calendar year 2014

Energy Technology Data Exchange (ETDEWEB)

Layton, Deborah L. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-06-01

The requirements for the reporting of polychlorinated biphenyl (PCB)-related activities are found in 40 Code of Federal Regulations (CFR) 761 Subpart J, "General Records and Reports." The PCB Annual Document Log is a detailed record of the PCB waste handling activities at the facility. The facility must prepare it each year by July 1 and maintain it at the facility for at least 3 years after the facility ceases using or storing PCBs and PCB items. While submittal of the PCB Annual Document Log to the U.S. Environmental Protection Agency (EPA) is not required by regulation, EPA has verbally requested in telephone conversations that this report be submitted to them on an annual basis. The Annual Records are not required to be submitted to EPA and are not considered to be part of the Annual Document Log, but are included to provide the complete disposition history or status of all PCB activities during the year. The Annual Document Log section of this report (Section 2.0) meets the requirements of 40 CFR 761.180(a)(2), as applicable, while the Annual Records section (Section 3.0) meets the requirement of 40 CFR 761.180(a)(1).

Polymer derived non-oxide ceramics modified with late transition metals.

Science.gov (United States)

Zaheer, Muhammad; Schmalz, Thomas; Motz, Günter; Kempe, Rhett

2012-08-07

This tutorial review highlights the methods for the preparation of metal modified precursor derived ceramics (PDCs) and concentrates on the rare non-oxide systems enhanced with late transition metals. In addition to the main synthetic strategies for modified SiC and SiCN ceramics, an overview of the morphologies, structures and compositions of both, ceramic materials and metal (nano) particles, is presented. Potential magnetic and catalytic applications have been discussed for the so manufactured metal containing non-oxide ceramics.

Idaho National Laboratory PCB Annual Document Log and Annual Records Report for Calendar Year 2013

Energy Technology Data Exchange (ETDEWEB)

no name on report

2014-06-01

The requirements for the reporting of polychlorinated biphenyl (PCB)-related activities are found in 40 Code of Federal Regulations (CFR) 761 Subpart J, "General Records and Reports." The PCB Annual Document Log is a detailed record of the PCB waste handling activities at the facility. The facility must prepare it each year by July 1 and maintain it at the facility for at least 3 years after the facility ceases using or storing PCBs and PCB items. While submittal of the PCB Annual Document Log to the U.S. Environmental Protection Agency (EPA) is not required by regulation, EPA has verbally requested in telephone conversations that this report be submitted to them on an annual basis. The Annual Document Log section of this report meets the requirements of 40 CFR 761.180(a)(2), as applicable, while the Annual Records section meets the requirement of 40 CFR 761.180(a)(1).

SEASONAL INFLUENCES ON PCB RETENTION AND BIOTRANSFORMATION IN FISH

Science.gov (United States)

James, Margaret O.; Kleinow, Kevin M.

2013-01-01

There is extensive evidence that fish from waters with PCB-contaminated sediments accumulate PCBs and related chemicals, and that people who eat fish from contaminated waters have higher body burdens of PCBs and PCB metabolites than those who do not. PCBs and their metabolites are potentially toxic, thus it is important to human health to understand the uptake, biotransformation and elimination of PCBs in fish, since these processes determine the extent of accumulation. The intestinal uptake of PCBs present in the diet of fish into fish tissues is a process that is influenced by the lipid composition of the diet. Biotransformation of PCBs in fish, as in mammals, facilitates elimination, although many PCB congeners are recalcitrant to biotransformation in fish and mammals. Sequential biotransformation of PCBs by cytochrome P450 and conjugation pathways is even less efficient in fish than in mammalian species, thus contributing to the retention of PCBs in fish tissues. A very important factor influencing overall PCB disposition in fish is water temperature. Seasonal changes in water temperature produce adaptive physiological and biochemical changes in fish. While uptake of PCBs from the diet is similar in fish acclimated to winter or summer temperatures, there is evidence that elimination of PCBs occurs much more slowly when the fish is acclimated at low temperatures than at warmer temperatures. Research to date suggests that the processes of elimination of PCBs are modulated by several factors in fish including seasonal changes in water temperature. Thus, the body burden of PCBs in fish from a contaminated location is likely to vary with season. PMID:23494683

Improved Plasticity of Ti-Based Bulk Metallic Glass at Room Temperature by Electroless Thin Nickel Coating

Directory of Open Access Journals (Sweden)

Xin Wang

2017-12-01

Full Text Available By restricting the dilated deformation, surface modification can stimulate multiple shear banding and improve the plasticity of bulk metallic glasses (BMGs. Aimed at modifying the surface of BMGs by thin layers, a crystalline Ni coating with ultrafine grains was coated on the surface of a Ti-based BMG by electroless plating. With a thickness of about 10 μm, the prepared thin coating could effectively limit the fast propagation of primary shear bands and stimulate the nucleation of multiple shear bands. As a result, the compression plasticity of the coated Ti-based BMG was improved to about 3.7% from near 0% of the non-coated BMG. Except for a small amount of Ni coating was adhered to the BMG substrate after fracture, most of the coatings were peeled off from the surface. It can be attributed to the abnormal growth of some coarse grains/particles in local region of the coating, which induces a large tensile stress at the interface between the coating and the BMG substrate. It is suggested that, for electroless nickel plating, improving the adhesive bonding strength between the coating and the substrate has a better geometric restriction effect than simply increasing the thickness of the coating.

Radiation damage in non-metals

International Nuclear Information System (INIS)

Stoneham, A.M.

1980-01-01

Work on the problem of radiation damage in non-metals over the past 25 years is reviewed with especial emphasis on the contribution made at AERE, Harwell and in particular by members of the Theoretical Physics Division. In the years between 1954 and the end of the 1960's the main thrust in the radiation damage of non-metals was model-building including devising defect models and mechanisms that were qualitatively acceptable, and compiling systematic data. The early 1970's made greater quantitative demands as computer techniques made theory more powerful. In many cases it was possible to predict defect properties accurately, so that one could distinguish between different defect models which were hard to tell apart by experiment alone. In the late 1970's the most important aspect has moved towards mechanisms of defect processes, especially in cases where experiment by itself is limited by timescale, by complexity, by the unintentional impurities inevitable in real crystals, or by the extreme conditions required. (UK)

Electroremediation of PCB contaminated soil combined with iron nanoparticles: Effect of the soil type.

Science.gov (United States)

Gomes, Helena I; Dias-Ferreira, Celia; Ottosen, Lisbeth M; Ribeiro, Alexandra B

2015-07-01

Polychlorinated biphenyls (PCB) are carcinogenic and persistent organic pollutants that accumulate in soils and sediments. Currently, there is no cost-effective and sustainable remediation technology for these contaminants. In this work, a new combination of electrodialytic remediation and zero valent iron particles in a two-compartment cell is tested and compared to a more conventional combination of electrokinetic remediation and nZVI in a three-compartment cell. In the new two-compartment cell, the soil is suspended and stirred simultaneously with the addition of zero valent iron nanoparticles. Remediation experiments are made with two different historically PCB contaminated soils, which differ in both soil composition and contamination source. Soil 1 is a mix of soils with spills of transformer oils, while Soil 2 is a superficial soil from a decommissioned school where PCB were used as windows sealants. Saponin, a natural surfactant, was also tested to increase the PCB desorption from soils and enhance dechlorination. Remediation of Soil 1 (with highest pH, carbonate content, organic matter and PCB concentrations) obtained the maximum 83% and 60% PCB removal with the two-compartment and the three-compartment cell, respectively. The highest removal with Soil 2 were 58% and 45%, in the two-compartment and the three-compartment cell, respectively, in the experiments without direct current. The pH of the soil suspension in the two-compartment treatment appears to be a determining factor for the PCB dechlorination, and this cell allowed a uniform distribution of the nanoparticles in the soil, while there was iron accumulation in the injection reservoir in the three-compartment cell. Copyright © 2015 Elsevier Ltd. All rights reserved.

Modelling PCB bioaccumulation in a Baltic food web

International Nuclear Information System (INIS)

Nfon, Erick; Cousins, Ian T.

2007-01-01

A steady state model is developed to describe the bioaccumulation of organic contaminants by 14 species in a Baltic food web including pelagic and benthic aquatic organisms. The model is used to study the bioaccumulation of five PCB congeners of different chlorination levels. The model predictions are evaluated against monitoring data for five of the species in the food web. Predicted concentrations are on average within a factor of two of measured concentrations. The model shows that all PCB congeners were biomagnified in the food web, which is consistent with observations. Sensitivity analysis reveals that the single most sensitive parameter is log K OW . The most sensitive environmental parameter is the annual average temperature. Although not identified amongst the most sensitive input parameters, the dissolved concentration in water is believed to be important because of the uncertainty in its determination. The most sensitive organism-specific input parameters are the fractional respiration of species from the water column and sediment pore water, which are also difficult to determine. Parameters such as feeding rate, growth rate and lipid content of organism are only important at higher trophic levels. - The bioaccumulation behaviour of PCB congeners in a Baltic food web is studied using a novel mechanistic model

Guangxi non-ferrous metal industry speeding up its restructuring

Institute of Scientific and Technical Information of China (English)

2007-01-01

<正>Non-ferrous metal industry in Guangxi takes an important position in China.However,the waste of resources is severe due to its simple industrial structure,small size of enterprises, sloppy technology,scattered layout,obstructed market and indiscriminate mining.Starting from last year,Guangxi began the project of building a world-influential non-ferrous metal

Behavioral changes following PCB 153 exposure in the Spontaneously Hypertensive rat – an animal model of Attention-Deficit/Hyperactivity disorder

Science.gov (United States)

2014-01-01

Background Attention-Deficit/Hyperactivity Disorder (ADHD) is a behavioral disorder affecting 3-5% of children. Although ADHD is highly heritable, environmental factors like exposure during early development to various toxic substances like polychlorinated biphenyls (PCBs) may contribute to the prevalence. PCBs are a group of chemical industrial compounds with adverse effects on neurobiological and cognitive functioning, and may produce behavioral impairments that share significant similarities with ADHD. The present study examined the relation between exposure to PCB 153 and changes in ADHD-like behavior in an animal model of ADHD, the spontaneously hypertensive rats (SHR/NCrl), and in Wistar Kyoto (WKY/NHsd) controls. Methods SHR/NCrl and WKY/NHsd, males and females, were orally given PCB 153 dissolved in corn oil at around postnatal day (PND) 8, 14, and 20 at a dosage of 1, 3 or 6 mg/kg bodyweight at each exposure. The control groups were orally administered corn oil only. The animals were behaviorally tested for exposure effects from PND 37 to 64 using an operant procedure. Results Exposure to PCB 153 was associated with pronounced and long-lasting behavioral changes in SHR/NCrl. Exposure effects in the SHR/NCrl depended on dose, where 1 mg/kg tended to reduce ADHD-like behaviors and produce opposite behavioral effects compared to 3 mg/kg and 6 mg/kg, especially in the females. In the WKY/NHsd controls and for the three doses tested, PCB 153 exposure produced a few specific behavioral changes only in males. The data suggest that PCB 153 exposure interacts with strain and sex, and also indicate a non-linear dose–response relation for the behaviors observed. Conclusions Exposure to PCB 153 seems to interact with several variables including strain, sex, dose, and time of testing. To the extent that the present findings can be generalized to humans, exposure effects of PCB 153 on ADHD behavior depends on amount of exposure, where high doses may aggravate ADHD

A highly sensitive and selective aptamer-based colorimetric sensor for the rapid detection of PCB 77.

Science.gov (United States)

Cheng, Ruojie; Liu, Siyao; Shi, Huijie; Zhao, Guohua

2018-01-05

A highly sensitive, specific and simple colorimetric sensor based on aptamer was established for the detection of polychlorinated biphenyls (PCB 77). The use of unmodified gold nanoparticles as a colorimetric probe for aptamer sensors enabled the highly sensitive and selective detection of polychlorinated biphenyls (PCB 77). A linear range of 0.5nM to 900nM was obtained for the colorimetric assay with a minimum detection limit of 0.05nM. In addition, by the methods of circular dichroism, UV and naked eyes, we found that the 35 base fragments retained after cutting 5 bases from the 5 'end of aptamer plays the most significant role in the PCB 77 specific recognition process. We found a novel way to truncated nucleotides to optimize the detection of PCB 77, and the selected nucleotides also could achieve high affinity with PCB 77. At the same time, the efficient detection of the PCB 77 by our colorimetric sensor in the complex environmental water samples was realized, which shows a good application prospect. Copyright © 2017 Elsevier B.V. All rights reserved.

The mineral base and productive capacities of metals and non-metals of Kosovo

Science.gov (United States)

Rizaj, M.; Beqiri, E.; McBow, I.; O'Brien, E. Z.; Kongoli, F.

2008-08-01

All historical periods of Kosovo—Ilirik, Roman, Medieval, Turkish, and former Yugoslavian—are linked with the intensive development of mining and metallurgy. This activity influenced and still is influencing the overall position of Kosovo as a country. For example, according to a 2006 World Bank report as well as other studies, Kosovo has potential lignite resources (geological reserves) of about 1.5 billion tonnes, which are ranked fifth in the world in importance. Other significant Kosovan mineral resources include lead, zinc, gold, silver, bauxite, and uranium, and rare metals accompanying those minerals, including indium, cadmium, thallium, gallium, and bismuth. These rare metals are of particular importance in developing advanced industrial technologies. Kosovo also has reserves of high-quality non-metals, including magnesite, quartz grit, bentonite, argil, talc, and asbestos. No database exists for these non-metal reserves, and further research and studies are needed.

Radiation-hardened bulk CMOS technology

International Nuclear Information System (INIS)

Dawes, W.R. Jr.; Habing, D.H.

1979-01-01

The evolutionary development of a radiation-hardened bulk CMOS technology is reviewed. The metal gate hardened CMOS status is summarized, including both radiation and reliability data. The development of a radiation-hardened bulk silicon gate process which was successfully implemented to a commercial microprocessor family and applied to a new, radiation-hardened, LSI standard cell family is also discussed. The cell family is reviewed and preliminary characterization data is presented. Finally, a brief comparison of the various radiation-hardened technologies with regard to performance, reliability, and availability is made

Green tea diet decreases PCB 126-induced oxidative stress in mice by upregulating antioxidant enzymes

Science.gov (United States)

Newsome, Bradley J; Petriello, Michael C; Han, Sung Gu; Murphy, Margaret O; Eske, Katryn E; Sunkara, Manjula; Morris, Andrew J; Hennig, Bernhard

2013-01-01

Superfund chemicals such as polychlorinated biphenyls pose a serious human health risk due to their environmental persistence and link to multiple diseases. Selective bioactive food components such as flavonoids have been shown to ameliorate PCB toxicity, but primarily in an in vitro setting. Here, we show that mice fed a green tea-enriched diet and subsequently exposed to environmentally relevant doses of coplanar PCB exhibit decreased overall oxidative stress primarily due to the upregulation of a battery of antioxidant enzymes. C57BL/6 mice were fed a low fat diet supplemented with green tea extract (GTE) for 12 weeks and exposed to 5 μmol PCB 126/kg mouse weight (1.63 mg/kg-day) on weeks 10, 11 and 12 (total body burden: 4.9 mg/kg). F2-Isoprostane and its metabolites, established markers of in vivo oxidative stress, measured in plasma via HPLC-MS/MS exhibited five-fold decreased levels in mice supplemented with GTE and subsequently exposed to PCB compared to animals on a control diet exposed to PCB. Livers were collected and harvested for both mRNA and protein analyses, and it was determined that many genes transcriptionally controlled by AhR and Nrf2 proteins were upregulated in PCB-exposed mice fed the green tea supplemented diet. An increased induction of genes such as SOD1, GSR, NQO1 and GST, key antioxidant enzymes, in these mice (green tea plus PCB) may explain the observed decrease in overall oxidative stress. A diet supplemented with green tea allows for an efficient antioxidant response in the presence of PCB 126 which supports the emerging paradigm that healthful nutrition may be able to bolster and buffer a physiological system against the toxicities of environmental pollutants. PMID:24378064

21 CFR 888.3120 - Ankle joint metal/polymer non-constrained cemented prosthesis.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Ankle joint metal/polymer non-constrained cemented... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES ORTHOPEDIC DEVICES Prosthetic Devices § 888.3120 Ankle joint metal/polymer non-constrained cemented prosthesis. (a) Identification. An ankle joint metal/polymer non...

Induction detection of concealed bulk banknotes

International Nuclear Information System (INIS)

Fuller, Christopher; Chen, Antao

2011-01-01

Bulk cash smuggling is a serious issue that has grown in volume in recent years. By building on the magnetic characteristics of paper currency, induction sensing is found to be capable of quickly detecting large masses of banknotes. The results show that this method is effective in detecting bulk cash through concealing materials such as plastics, cardboards, fabrics and aluminum foil. The significant difference in the observed phase between the received signals caused by conducting materials and ferrite compounds, found in banknotes, provides a good indication that this process can overcome the interference by metal objects in a real sensing application. This identification strategy has the potential to not only detect the presence of banknotes, but also the number, while still eliminating false positives caused by metal objects

Bioremediation trial on aged PCB-polluted soils--a bench study in Iceland.

Science.gov (United States)

Lehtinen, Taru; Mikkonen, Anu; Sigfusson, Bergur; Ólafsdóttir, Kristín; Ragnarsdóttir, Kristín Vala; Guicharnaud, Rannveig

2014-02-01

Polychlorinated biphenyls (PCBs) pose a threat to the environment due to their high adsorption capacity to soil organic matter, stability and low reactivity, low water solubility, toxicity and ability to bioaccumulate. With Icelandic soils, research on contamination issues has been very limited and no data has been reported either on PCB degradation potential or rate. The goals of this research were to assess the bioavailability of aged PCBs in the soils of the old North Atlantic Treaty Organization facility in Keflavík, Iceland and to find the best biostimulation method to decrease the pollution. The effectiveness of different biostimulation additives (N fertiliser, white clover and pine needles) at different temperatures (10 and 30 °C) and oxygen levels (aerobic and anaerobic) were tested. PCB bioavailability to soil fauna was assessed with earthworms (Eisenia foetida). PCBs were bioavailable to earthworms (bioaccumulation factor 0.89 and 0.82 for earthworms in 12.5 ppm PCB soil and in 25 ppm PCB soil, respectively), with less chlorinated congeners showing higher bioaccumulation factors than highly chlorinated congeners. Biostimulation with pine needles at 10 °C under aerobic conditions resulted in nearly 38 % degradation of total PCBs after 2 months of incubation. Detection of the aerobic PCB degrading bphA gene supports the indigenous capability of the soils to aerobically degrade PCBs. Further research on field scale biostimulation trials with pine needles in cold environments is recommended in order to optimise the method for onsite remediation.

Resveratrol via sirtuin-1 downregulates RE1-silencing transcription factor (REST) expression preventing PCB-95-induced neuronal cell death.

Science.gov (United States)

Guida, Natascia; Laudati, Giusy; Anzilotti, Serenella; Secondo, Agnese; Montuori, Paolo; Di Renzo, Gianfranco; Canzoniero, Lorella M T; Formisano, Luigi

2015-11-01

Resveratrol (3,5,4'-trihydroxystilbene) (RSV), a polyphenol widely present in plants, exerts a neuroprotective function in several neurological conditions; it is an activator of class III histone deacetylase sirtuin1 (SIRT1), a crucial regulator in the pathophysiology of neurodegenerative diseases. By contrast, the RE1-silencing transcription factor (REST) is involved in the neurotoxic effects following exposure to polychlorinated biphenyl (PCB) mixture A1254. The present study investigated the effects of RSV-induced activation of SIRT1 on REST expression in SH-SY5Y cells. Further, we investigated the possible relationship between the non-dioxin-like (NDL) PCB-95 and REST through SIRT1 to regulate neuronal death in rat cortical neurons. Our results revealed that RSV significantly decreased REST gene and protein levels in a dose- and time-dependent manner. Interestingly, overexpression of SIRT1 reduced REST expression, whereas EX-527, an inhibitor of SIRT1, increased REST expression and blocked RSV-induced REST downregulation. These results suggest that RSV downregulates REST through SIRT1. In addition, RSV enhanced activator protein 1 (AP-1) transcription factor c-Jun expression and its binding to the REST promoter gene. Indeed, c-Jun knockdown reverted RSV-induced REST downregulation. Intriguingly, in SH-SY5Y cells and rat cortical neurons the NDL PCB-95 induced necrotic cell death in a concentration-dependent manner by increasing REST mRNA and protein expression. In addition, SIRT1 knockdown blocked RSV-induced neuroprotection in rat cortical neurons treated with PCB-95. Collectively, these results indicate that RSV via SIRT1 activates c-Jun, thereby reducing REST expression in SH-SY5Y cells under physiological conditions and blocks PCB-95-induced neuronal cell death by activating the same SIRT1/c-Jun/REST pathway. Copyright © 2015 Elsevier Inc. All rights reserved.

Analysis on the phase transition behavior of Cu base bulk metallic glass by electrical resistivity measurement

International Nuclear Information System (INIS)

Ji, Young Su; Chung, Sung Jae; Ok, Myoung-Ryul; Hong, Kyung Tae; Suh, Jin-Yoo; Byeon, Jai Won; Yoon, Jin-Kook; Lee, Kyung Hwan; Lee, Kyung Sub

2007-01-01

The crystallization behavior of Cu 43 Zr 43 Al 7 Ag 7 (numbers indicate at.%) bulk metallic glass was investigated using the isothermal electrical resistivity measurements at 450 deg. C in the supercooled liquid region. The crystallization process is a single step phase transformation. To analyze the electrical resistivity reduction, microstructure evolutions were analyzed using differential scanning calorimetry, X-ray diffraction, transmission electron microscopy and small-angle X-ray scattering. The Avrami parameter of the electrical resistivity reduction step was 1.73, indicating that the crystallization process is a diffusion-controlled growth of intermetallic compounds with decreasing nucleation rate

Results and evaluation of the first study of organochlorine contaminants (PCDDs, PCDFs, PCBs and DDTs), heavy metals and metalloids in birds from Baja California, Mexico

Energy Technology Data Exchange (ETDEWEB)

Jimenez, Begona [Department of Instrumental Analysis and Environmental Chemistry, Institute of Organic Chemistry, CSIC, Juan de la Cierva 3, 28006 Madrid (Spain)]. E-mail: bjimenez@iqog.csic.es; Rodriguez-Estrella, Ricardo [Centro de Investigaciones Biologicas del Noroeste, Mar Bermejo 195, Apdo. Postal 128, La Paz, Baja California Sur (Mexico); Merino, Ruben [Department of Instrumental Analysis and Environmental Chemistry, Institute of Organic Chemistry, CSIC, Juan de la Cierva 3, 28006 Madrid (Spain); Gomez, Gema [Department of Instrumental Analysis and Environmental Chemistry, Institute of Organic Chemistry, CSIC, Juan de la Cierva 3, 28006 Madrid (Spain); Rivera, Laura [Centro de Investigaciones Biologicas del Noroeste, Mar Bermejo 195, Apdo. Postal 128, La Paz, Baja California Sur (Mexico); Jose Gonzalez, Maria [Department of Instrumental Analysis and Environmental Chemistry, Institute of Organic Chemistry, CSIC, Juan de la Cierva 3, 28006 Madrid (Spain); Abad, Esteban [Department of Ecotechnologies, Research and Development Center, CSIC, Jordi Girona, 18-26, 08034 Barcelona (Spain); Rivera, Josep [Department of Ecotechnologies, Research and Development Center, CSIC, Jordi Girona, 18-26, 08034 Barcelona (Spain)

2005-01-01

Organochlorine compounds (OCs) including polychlorinated dibenzo-p-dioxins (PCDDs), dibenzofurans (PCDFs), polychlorinated biphenyls (PCBs) and 1,1-dichloro-2,2-bis(p-chlorophenyl)ethylene (p-p'-DDE), heavy metals (Pb, Cd, Zn, Cu), and arsenic were measured in house sparrows (Passer domesticus) and common ground doves (Columbina passerina) from Baja California Sur, Mexico. Concentrations of PCDD/Fs were low, with 21 pg/g for house sparrows, and 7.7 pg/g for common ground doves. Non-ortho-PCB concentrations in house sparrow and common ground doves were 58 and 254 pg/g, respectively, and are within the highest concentrations reported in species that are in the low levels of food webs. The major differences in organochlorine levels between species were found for ortho-PCBs and DDTs. ortho-PCB levels were higher in the seedeater species, whereas DDT levels were higher in the omnivorous species. Heavy metal levels were far below those associated with negative effects. - Capsule: The first data on contaminants in birds from Baja California is given.

Results and evaluation of the first study of organochlorine contaminants (PCDDs, PCDFs, PCBs and DDTs), heavy metals and metalloids in birds from Baja California, Mexico

International Nuclear Information System (INIS)

Jimenez, Begona; Rodriguez-Estrella, Ricardo; Merino, Ruben; Gomez, Gema; Rivera, Laura; Jose Gonzalez, Maria; Abad, Esteban; Rivera, Josep

2005-01-01

Organochlorine compounds (OCs) including polychlorinated dibenzo-p-dioxins (PCDDs), dibenzofurans (PCDFs), polychlorinated biphenyls (PCBs) and 1,1-dichloro-2,2-bis(p-chlorophenyl)ethylene (p-p'-DDE), heavy metals (Pb, Cd, Zn, Cu), and arsenic were measured in house sparrows (Passer domesticus) and common ground doves (Columbina passerina) from Baja California Sur, Mexico. Concentrations of PCDD/Fs were low, with 21 pg/g for house sparrows, and 7.7 pg/g for common ground doves. Non-ortho-PCB concentrations in house sparrow and common ground doves were 58 and 254 pg/g, respectively, and are within the highest concentrations reported in species that are in the low levels of food webs. The major differences in organochlorine levels between species were found for ortho-PCBs and DDTs. ortho-PCB levels were higher in the seedeater species, whereas DDT levels were higher in the omnivorous species. Heavy metal levels were far below those associated with negative effects. - Capsule: The first data on contaminants in birds from Baja California is given

Development of Cu-Hf-Al ternary systems and tungsten wire/particle reinforced Cu48Hf43Al9 bulk metallic glass composites for strengthening

International Nuclear Information System (INIS)

Park, Joyoung; An, Jihye; Choi-Yim, Haein

2010-01-01

Stable bulk glass forming alloys can be developed over a wide range of compositions in Cu-Hf-Al ternary systems starting from the Cu 49 Hf 42 Al 9 bulk metallic glass. Ternary Cu-Hf-Al alloys can be cast directly from the melt into copper molds to form fully amorphous strips with thicknesses of 1 to 6 mm. The maximum critical diameter of the new Cu-Hf-Al ternary alloy was 6 mm. X-ray diffraction patterns were used to confirm the amorphous nature of the ternary Cu-Hf-Al alloys. To increase the toughness of these metallic glasses, we reinforced the Cu 48 Hf 43 Al 9 bulk metallic glass-forming liquid with a 50% volume fraction of tungsten particles and an 80% volume fraction of tungsten wires with diameters of 242.4 μm. Composites with a critical diameter of 7 mm and length 70 mm were synthesized. The structure of the composites was confirmed by using X-ray diffraction (XRD), and the scanning electron microscopy (SEM). The mechanical properties of the composites were studied in compression tests. The thermal stability and the crystallization processes of the Cu-Hf-Al alloys and composites were investigated by using differential scanning calorimetry (DSC). Values of the glass transition temperature (T g ), the crystallization temperature (T x ), and the supercooled liquid region (ΔT = T x - T g ) are given in this paper.

Investigating Intergenerational Differences in Human PCB Exposure due to Variable Emissions and Reproductive Behaviors