TRU drum corrosion task team report

Energy Technology Data Exchange (ETDEWEB)

Kooda, K.E.; Lavery, C.A.; Zeek, D.P.

1996-05-01

During routine inspections in March 1996, transuranic (TRU) waste drums stored at the Radioactive Waste Management Complex (RWMC) were found with pinholes and leaking fluid. These drums were overpacked, and further inspection discovered over 200 drums with similar corrosion. A task team was assigned to investigate the problem with four specific objectives: to identify any other drums in RWMC TRU storage with pinhole corrosion; to evaluate the adequacy of the RWMC inspection process; to determine the precise mechanism(s) generating the pinhole drum corrosion; and to assess the implications of this event for WIPP certifiability of waste drums. The task team investigations analyzed the source of the pinholes to be Hcl-induced localized pitting corrosion. Hcl formation is directly related to the polychlorinated hydrocarbon volatile organic compounds (VOCs) in the waste. Most of the drums showing pinhole corrosion are from Content Code-003 (CC-003) because they contain the highest amounts of polychlorinated VOCs as determined by headspace gas analysis. CC-001 drums represent the only other content code with a significant number of pinhole corrosion drums because their headspace gas VOC content, although significantly less than CC-003, is far greater than that of the other content codes. The exact mechanisms of Hcl formation could not be determined, but radiolytic and reductive dechlorination and direct reduction of halocarbons were analyzed as the likely operable reactions. The team considered the entire range of feasible options, ranked and prioritized the alternatives, and recommended the optimal solution that maximizes protection of worker and public safety while minimizing impacts on RWMC and TRU program operations.

TRU drum corrosion task team report

International Nuclear Information System (INIS)

Kooda, K.E.; Lavery, C.A.; Zeek, D.P.

1996-05-01

During routine inspections in March 1996, transuranic (TRU) waste drums stored at the Radioactive Waste Management Complex (RWMC) were found with pinholes and leaking fluid. These drums were overpacked, and further inspection discovered over 200 drums with similar corrosion. A task team was assigned to investigate the problem with four specific objectives: to identify any other drums in RWMC TRU storage with pinhole corrosion; to evaluate the adequacy of the RWMC inspection process; to determine the precise mechanism(s) generating the pinhole drum corrosion; and to assess the implications of this event for WIPP certifiability of waste drums. The task team investigations analyzed the source of the pinholes to be Hcl-induced localized pitting corrosion. Hcl formation is directly related to the polychlorinated hydrocarbon volatile organic compounds (VOCs) in the waste. Most of the drums showing pinhole corrosion are from Content Code-003 (CC-003) because they contain the highest amounts of polychlorinated VOCs as determined by headspace gas analysis. CC-001 drums represent the only other content code with a significant number of pinhole corrosion drums because their headspace gas VOC content, although significantly less than CC-003, is far greater than that of the other content codes. The exact mechanisms of Hcl formation could not be determined, but radiolytic and reductive dechlorination and direct reduction of halocarbons were analyzed as the likely operable reactions. The team considered the entire range of feasible options, ranked and prioritized the alternatives, and recommended the optimal solution that maximizes protection of worker and public safety while minimizing impacts on RWMC and TRU program operations

29 CFR 1915.173 - Drums and containers.

Science.gov (United States)

2010-07-01

... 29 Labor 7 2010-07-01 2010-07-01 false Drums and containers. 1915.173 Section 1915.173 Labor... Vessels, Drums and Containers, Other Than Ship's Equipment § 1915.173 Drums and containers. (a) Shipping drums and containers shall not be pressurized to remove their contents. (b) A temporarily assembled...

FIFTY-FIVE GALLON DRUM STANDARD STUDY

International Nuclear Information System (INIS)

Puigh, R.J.

2009-01-01

Fifty-five gallon drums are routinely used within the U.S. for the storage and eventual disposal of fissionable materials as Transuranic or low-level waste. To support these operations, criticality safety evaluations are required. A questionnaire was developed and sent to selected Endusers at Hanford, Idaho National Laboratory, Lawrence Livermore National Laboratory, Oak Ridge and the Savannah River Site to solicit current practices. This questionnaire was used to gather information on the kinds of fissionable materials packaged into drums, the models used in performing criticality safety evaluations in support of operations involving these drums, and the limits and controls established for the handling and storage of these drums. The completed questionnaires were reviewed and clarifications solicited through individual communications with each Enduser to obtain more complete and consistent responses. All five sites have similar drum operations involving thousands to tens of thousands of fissionable material waste drums. The primary sources for these drums are legacy (prior operations) and decontamination and decommissioning wastes at all sites except Lawrence Livermore National Laboratory. The results from this survey and our review are discussed in this paper

Vapor generator steam drum spray heat

International Nuclear Information System (INIS)

Fasnacht, F.A. Jr.

1978-01-01

A typical embodiment of the invention provides a combination feedwater and cooldown water spray head that is centrally disposed in the lower portion of a nuclear power plant steam drum. This structure not only discharges the feedwater in the hottest part of the steam drum, but also increases the time required for the feedwater to reach the steam drum shell, thereby further increasing the feedwater temperature before it contacts the shell surface, thus reducing thermal shock to the steam drum structure

Exotic species with explicit noble metal-noble gas-noble metal linkages.

Science.gov (United States)

Moreno, Norberto; Restrepo, Albeiro; Hadad, C Z

2018-02-14

We present a study of the isoelectronic Pt 2 Ng 2 F 4 and [Au 2 Ng 2 F 4 ] 2+ species with noble gas atoms (Ng = Kr, Xe, Rn) acting as links bridging the two noble metal atoms. The stability of the species is investigated using several thermodynamic, kinetic and reactivity indicators. The results are compared against [AuXe 4 ] 2+ , which is thermodynamically unstable in the gas phase but is stabilized in the solid state to the point that it has been experimentally detected as [AuXe 4 ](Sb 2 F 11 ) 2 (S. Seidel and K. Seppelt, Science, 2000, 290, 117-118). Our results indicate that improving upon [AuXe 4 ] 2+ , these exotic combinations between the a priori non-reactive noble metals and noble gases lead to metastable species, and, therefore, they have the possibility of existing in the solid state under adequate conditions. Our calculations include accurate energies and geometries at both the CCSD/SDDALL and MP2/SDDALL levels. We offer a detailed description of the nature of the bonding interactions using orbital and density-based analyses. The computational evidence suggests partially covalent and ionic interactions as the stabilization factors.

21 CFR 886.1200 - Optokinetic drum.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Optokinetic drum. 886.1200 Section 886.1200 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL... optokinetic drum is a drum-like device covered with alternating white and dark stripes or pictures that can be...

The coke drum thermal kinetic effects

Energy Technology Data Exchange (ETDEWEB)

Aldescu, Maria M.; Romero, Sim; Larson, Mel [KBC Advanced Technologies plc, Surrey (United Kingdom)

2012-07-01

The coke drum thermal kinetic dynamics fundamentally affect the coker unit yields as well as the coke product properties and unit reliability. In the drum the thermal cracking and polymerization or condensation reactions take place in a semi-batch environment. Understanding the fundamentals of the foaming kinetics that occur in the coke drums is key to avoiding a foam-over that could result in a unit shutdown for several months. Although the most dynamic changes with time occur during drum filling, other dynamics of the coker process will be discussed as well. KBC has contributed towards uncovering and modelling the complexities of heavy oil thermal dynamics. (author)

Modeling VOC transport in simulated waste drums

International Nuclear Information System (INIS)

Liekhus, K.J.; Gresham, G.L.; Peterson, E.S.; Rae, C.; Hotz, N.J.; Connolly, M.J.

1993-06-01

A volatile organic compound (VOC) transport model has been developed to describe unsteady-state VOC permeation and diffusion within a waste drum. Model equations account for three primary mechanisms for VOC transport from a void volume within the drum. These mechanisms are VOC permeation across a polymer boundary, VOC diffusion across an opening in a volume boundary, and VOC solubilization in a polymer boundary. A series of lab-scale experiments was performed in which the VOC concentration was measured in simulated waste drums under different conditions. A lab-scale simulated waste drum consisted of a sized-down 55-gal metal drum containing a modified rigid polyethylene drum liner. Four polyethylene bags were sealed inside a large polyethylene bag, supported by a wire cage, and placed inside the drum liner. The small bags were filled with VOC-air gas mixture and the VOC concentration was measured throughout the drum over a period of time. Test variables included the type of VOC-air gas mixtures introduced into the small bags, the small bag closure type, and the presence or absence of a variable external heat source. Model results were calculated for those trials where the VOC permeability had been measured. Permeabilities for five VOCs [methylene chloride, 1,1,2-trichloro-1,2,2-trifluoroethane (Freon-113), 1,1,1-trichloroethane, carbon tetrachloride, and trichloroethylene] were measured across a polyethylene bag. Comparison of model and experimental results of VOC concentration as a function of time indicate that model accurately accounts for significant VOC transport mechanisms in a lab-scale waste drum

49 CFR 178.505 - Standards for aluminum drums.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Standards for aluminum drums. 178.505 Section 178... PACKAGINGS Non-bulk Performance-Oriented Packaging Standards § 178.505 Standards for aluminum drums. (a) The following are the identification codes for aluminum drums: (1) 1B1 for a non-removable head aluminum drum...

Development of SGS for various waste drums

International Nuclear Information System (INIS)

Kim, Ki-Hong; Ryu, Young-Gerl; Kwak, Kyung-Kil; Ji, Yong-Young

2006-01-01

Radioactive waste assay system was manufactured to measure the individual nuclides' activity in homogeneous and non-homogeneous waste drums and to exclude worker's exposure. After measuring the activities of all individual γ-emitters, our system was programmed to calculate the activities of α, Β emitters, automatically and then calculated total activities of drum by utilizing scaling factor (relationship between α, Β emitters and Co-60, Cs-137). In general, SGS (Segmented gamma Scanning system) divided a waste drum into 8 segments vertically, and also 8 sectors in one segment to minimize the error. And SGS can be determined the density of drum by using the several matrix correction methods such as transmission ratio, differential peak absorption and mean density correction, individually or by combination. However, from the NPPs and other nuclear facilities, various drum (100∼350L) could be generated. To analyze the activities of γ-emitters from various drums, we modified the collimator (horizontal and vertical) and added detector mover to the existing SGS system. As a results, the measurement error was <12% in a short distance (10 segments, Co-60; 47.87μCi and Cs-137; 101.16μCi) and was <25% in a long distance (8 segments, same sources). This system can be applied to the drum which TGS system does not analyze drum (for example, high density, high activities and large volume). (author)

Sound analysis of a cup drum

International Nuclear Information System (INIS)

Kim, Kun ho

2012-01-01

The International Young Physicists’ Tournament (IYPT) is a worldwide tournament that evaluates a high-school student's ability to solve various physics conundrums that have not been fully resolved in the past. The research presented here is my solution to the cup drum problem. The physics behind a cup drum has never been explored or modelled. A cup drum is a musical instrument that can generate different frequencies and amplitudes depending on the location of a cup held upside-down over, on or under a water surface. The tapping sound of a cup drum can be divided into two components: standing waves and plate vibration. By individually researching the nature of these two sounds, I arrived at conclusions that could accurately predict the frequencies in most cases. When the drum is very close to the surface, qualitative explanations are given. In addition, I examined the trend of the tapping sound amplitude at various distances and qualitatively explained the experimental results. (paper)

Drum inspection robots: Application development

International Nuclear Information System (INIS)

Hazen, F.B.; Warner, R.D.

1996-01-01

Throughout the Department of Energy (DOE), drums containing mixed and low level stored waste are inspected, as mandated by the Resource Conservation and Recovery Act (RCRA) and other regulations. The inspections are intended to prevent leaks by finding corrosion long before the drums are breached. The DOE Office of Science and Technology (OST) has sponsored efforts towards the development of robotic drum inspectors. This emerging application for mobile and remote sensing has broad applicability for DOE and commercial waste storage areas. Three full scale robot prototypes have been under development, and another project has prototyped a novel technique to analyze robotically collected drum images. In general, the robots consist of a mobile, self-navigating base vehicle, outfitted with sensor packages so that rust and other corrosion cues can be automatically identified. They promise the potential to lower radiation dose and operator effort required, while improving diligence, consistency, and documentation

Mechanical Modeling of a WIPP Drum Under Pressure

Energy Technology Data Exchange (ETDEWEB)

Smith, Jeffrey A. [Sandia National Laboratories, Albuquerque, NM (United States)

2014-11-25

Mechanical modeling was undertaken to support the Waste Isolation Pilot Plant (WIPP) technical assessment team (TAT) investigating the February 14th 2014 event where there was a radiological release at the WIPP. The initial goal of the modeling was to examine if a mechanical model could inform the team about the event. The intention was to have a model that could test scenarios with respect to the rate of pressurization. It was expected that the deformation and failure (inability of the drum to contain any pressure) would vary according to the pressurization rate. As the work progressed there was also interest in using the mechanical analysis of the drum to investigate what would happen if a drum pressurized when it was located under a standard waste package. Specifically, would the deformation be detectable from camera views within the room. A finite element model of a WIPP 55-gallon drum was developed that used all hex elements. Analyses were conducted using the explicit transient dynamics module of Sierra/SM to explore potential pressurization scenarios of the drum. Theses analysis show similar deformation patterns to documented pressurization tests of drums in the literature. The calculated failure pressures from previous tests documented in the literature vary from as little as 16 psi to 320 psi. In addition, previous testing documented in the literature shows drums bulging but not failing at pressures ranging from 69 to 138 psi. The analyses performed for this study found the drums failing at pressures ranging from 35 psi to 75 psi. When the drums are pressurized quickly (in 0.01 seconds) there is significant deformation to the lid. At lower pressurization rates the deformation of the lid is considerably less, yet the lids will still open from the pressure. The analyses demonstrate the influence of pressurization rate on deformation and opening pressure of the drums. Analyses conducted with a substantial mass on top of the closed drum demonstrate that the

Cookoff Modeling of a WIPP waste drum (68660)

Energy Technology Data Exchange (ETDEWEB)

Hobbs, Michael L. [Sandia National Laboratories, Albuquerque, NM (United States)

2014-11-24

A waste drum located 2150 feet underground may have been the root cause of a radiation leak on February 14, 2014. Information provided to the WIPP Technical Assessment Team (TAT) was used to describe the approximate content of the drum, which included an organic cat litter (Swheat Scoop®, or Swheat) composed of 100% wheat products. The drum also contained various nitrate salts, oxalic acid, and a nitric acid solution that was neutralized with triethanolamine (TEA). CTH-TIGER was used with the approximate drum contents to specify the products for an exothermic reaction for the drum. If an inorganic adsorbent such as zeolite had been used in lieu of the kitty litter, the overall reaction would have been endothermic. Dilution with a zeolite adsorbent might be a useful method to remediate drums containing organic kitty litter. SIERRA THERMAL was used to calculate the pressurization and ignition of the drum. A baseline simulation of drum 68660 was performed by assuming a background heat source of 0.5-10 W of unknown origin. The 0.5 W source could be representative of heat generated by radioactive decay. The drum ignited after about 70 days. Gas generation at ignition was predicted to be 300-500 psig with a sealed drum (no vent). At ignition, the wall temperature increases modestly by about 1°C, demonstrating that heating would not be apparent prior to ignition. The ignition location was predicted to be about 0.43 meters above the bottom center portion of the drum. At ignition only 3-5 kg (out of 71.6 kg total) has been converted into gas, indicating that most of the material remained available for post-ignition reaction.

Sealing of rotary drums for operation under pressurized conditions

International Nuclear Information System (INIS)

Shirvani, M.; Khanof, M. H.; Yousefi, M. R.; Sadighi, S.

2006-01-01

In practice, rotary drums are always designed for operation under vacuum conditions. In this paper, a novel technique is proposed for sealing the rotary drums under pressurized conditions. The proposed system is based on applying a secondary pressurized volume around the leaking gap of the drum. By controlling the pressure of this volume above the pressure of the drum, it will be possible to prevent from any leakage of gases to the ambient. The objective of a controller in this system is that the pressure of secondary volume be kept above the pressure of the drum in spite of the disturbances which may be exerted on the system by the wind outside the drum. The control system is also required to trace the variations in the drum pressure with the least fluctuations in the pressure difference among the drum and the volume

Gas formation in drum waste packages of Paks NPP

International Nuclear Information System (INIS)

Molnar, M.; Palcsu, L.; Svingor, E.; Szanto, Z.; Futo, I.; Ormai, P.

2000-01-01

Gas composition measurements have been carried out by mass spectrometry analysis of samples taken from the headspace of ten drum waste packages generated and temporarily stored at Paks NPP. Four drums contained compacted solid waste, three drums were filled with grouted (solidified) sludge and three drums contained solid waste without compaction. The drums have been equipped with a special gas outlet system to make repeated sampling possible. Based on the first measurements significant differences in the gas composition and the rate of gas generation among the drums were found. (author)

Packaging design criteria for the Type B Drum

International Nuclear Information System (INIS)

Edwards, W.S.; Smith, R.J.; Wells, A.H.

1995-09-01

The Type B Drum package is a transportation cask capable of shipping a single 55-gal (208 L) drum of transuranic (TRU) waste. The Type B Drum is smaller than existing certified packages, such as the TRUPACT-II cask, but will allow payloads with higher thermal and gas generation rates, thus providing greater operational flexibility. The Type B Drum package has double containment so that plutonium contents and other radioactive material may be transported in Type B quantities. Conceptual designs of unshielded and shielded versions of the Type B Drum were completed in Report on the Conceptual Design of the Unshielded Type B Drum Packaging and Report on the Conceptual Design of the Shielded type B Drum Packaging (WEC 1994a, WEC 1994b), which demonstrated the Type B Drum to be a viable packaging system. A Type B package containment system must withstand the normal conditions of transport and the hypothetical accident conditions, which include a 9-m (30-ft) drop onto an unyielding surface and a 1-m (3-ft) drop onto a 15-cm (6-in.) diameter pin, and a fire and immersion scenarios

Buoy-Rope-Drum Wave Power System

Directory of Open Access Journals (Sweden)

Linsen Zhu

2013-01-01

Full Text Available A buoy-rope-drum wave power system is a new type of floating oscillating buoy wave power device, which absorbs energy from waves by buoy-rope-drum device. Based on the linear deep water wave theory and pure resistive load, with cylinder buoy as an example, the research sets up the theoretical model of direct-drive buoy-rope-drum wave power efficiency and analyzes the influence of the mass and load of the system on its generating efficiency. It points out the two main categories of the efficient buoy-rope-drum wave power system: light thin type and resonance type, and optimal designs of their major parameters are carried out on the basis of the above theoretical model of generating efficiency.

Active Drumming Experience Increases Infants' Sensitivity to Audiovisual Synchrony during Observed Drumming Actions.

Science.gov (United States)

Gerson, Sarah A; Schiavio, Andrea; Timmers, Renee; Hunnius, Sabine

2015-01-01

In the current study, we examined the role of active experience on sensitivity to multisensory synchrony in six-month-old infants in a musical context. In the first of two experiments, we trained infants to produce a novel multimodal effect (i.e., a drum beat) and assessed the effects of this training, relative to no training, on their later perception of the synchrony between audio and visual presentation of the drumming action. In a second experiment, we then contrasted this active experience with the observation of drumming in order to test whether observation of the audiovisual effect was as effective for sensitivity to multimodal synchrony as active experience. Our results indicated that active experience provided a unique benefit above and beyond observational experience, providing insights on the embodied roots of (early) music perception and cognition.

DEGRADATION EVALUATION OF HEAVY WATER DRUMS AND TANKS

Energy Technology Data Exchange (ETDEWEB)

Mickalonis, J.; Vormelker, P.

2009-07-31

Heavy water with varying chemistries is currently being stored in over 6700 drums in L- and K-areas and in seven tanks in L-, K-, and C-areas. A detailed evaluation of the potential degradation of the drums and tanks, specific to their design and service conditions, has been performed to support the demonstration of their integrity throughout the desired storage period. The 55-gallon drums are of several designs with Type 304 stainless steel as the material of construction. The tanks have capacities ranging from 8000 to 45600 gallons and are made of Type 304 stainless steel. The drums and tanks were designed and fabricated to national regulations, codes and standards per procurement specifications for the Savannah River Site. The drums have had approximately 25 leakage failures over their 50+ years of use with the last drum failure occurring in 2003. The tanks have experienced no leaks to date. The failures in the drums have occurred principally near the bottom weld, which attaches the bottom to the drum sidewall. Failures have occurred by pitting, crevice and stress corrosion cracking and are attributable, in part, to the presence of chloride ions in the heavy water. Probable degradation mechanisms for the continued storage of heavy water were evaluated that could lead to future failures in the drum or tanks. This evaluation will be used to support establishment of an inspection plan which will include susceptible locations, methods, and frequencies for the drums and tanks to avoid future leakage failures.

Storage drums for radio-active waste

International Nuclear Information System (INIS)

Knights, H.C.

1982-01-01

The lid of a storage drum for radioactive waste is secured by a series of clamps each of which has a hook for engaging the rim of the drum. Each clamp has an indicating means whereby a remote operator can check that the lid is secured to the drum. In a second embodiment, the position of an arm acts as a visual indication as to whether or not the clamp is in engagement with the container rim. (author)

HANFORD Pu-238 DRUM INTEGRITY ASSESSMENT

International Nuclear Information System (INIS)

CANNELL, G.R.

2004-01-01

Hanford is presently retrieving contact-handled, transuranic (CH-TRU) waste drums from the site's Low-Level Burial Grounds (LLBG) for processing and disposition. A subgroup of these drums (12 total), referred to as Pu-238 drums, has some unique characteristics that may impact the current drum handling and processing activities. These characteristics include content, shielding, thermal, pressurization and criticality issues. An effort to evaluate these characteristics, for the purpose of developing a specific plan for safe retrieval of the Pu-238 drums, is underway. In addition to the above evaluation, the following integrity assessment of the inner container material and/or confinement properties, with primary emphasis on the Source Capsule (primary confinement barrier) and Shipping Container has been performed. Assessment included review of the inner container materials and the potential impact the service history may have had on material and/or confinement properties. Several environmental degradation mechanisms were considered with the objective of answering the following question: Is it likely the container material and/or confinement properties have been significantly altered as a result of service history?

Shearer drums - the cutting edge

Energy Technology Data Exchange (ETDEWEB)

O' Neill, M.; Wright, C.

2004-09-15

The paper discusses continuous miner and shearer cutters. It claims cutting drum require the same level of engineering know-how and technical expertise as do the machines driving them, and that the cutting drum, whether on a longwall shearer or continuous miner, comprises, the steel, pedestals, bit holders and the bits.

Metabolic Demands of Heavy Metal Drumming

Directory of Open Access Journals (Sweden)

Bryan Romero

2016-07-01

Full Text Available Background: The drum set involves dynamic movement of all four limbs. Motor control studies have been done on drum set playing, yet not much is known about the physiological responses to this activity. Even less is known about heavy metal drumming. Aims: The purpose of this study was to determine metabolic responses and demands of heavy metal drumming. Methods: Five semi-professional male drummers (mean ± SD age = 27.4 ± 2.6 y, height = 177.2 ± 3.8 cm, body mass = 85.1 ± 17.8 kg performed four prescribed and four self-selected heavy metal songs. Oxygen consumption (VO2, minute ventilation (VE and respiratory exchange ratio (RER were measured using a metabolic cart.  Heart rate (HR was measured using a heart rate monitor. VO2max was determined using a graded cycle ergometer test. Results: The results indicated a metabolic cost of 6.3 ± 1.4 METs and heart rate of 145.1 ± 15.7 beats·min-1 (75.4 ± 8.3% of age-predicted HRmax. VO2 peak values reached approximately 90% of the drummer’s VO2max when performing at the fastest speeds. According to these results, heavy metal drumming may be considered vigorous intensity activity (≥ 6.0 METs. The relative VO2max of 40.2 ± 9.5 mL·kg·min-1 leads to an aerobic fitness classification of “average” for adult males. Conclusions: The metabolic demands required during heavy metal drumming meet the American College of Sports Medicine guidelines for the development of health related fitness.  Keywords: Drum set, Exercise physiology, VO2, Music

Energy Expenditure in Rock/Pop Drumming

OpenAIRE

De La Rue, S; Draper, Stephen B; Potter, Christopher R; Smith, M.

2013-01-01

Despite the vigorous nature of rock/pop drumming, there are no precise data on the energy expenditure of this activity. The aim of this study was to quantify the energy cost of rock/pop drumming. Fourteen male drummers (mean +/- SD; age 27 +/- 8 yrs.) completed an incremental drumming test to establish the relationship between energy expenditure and heart rate for this activity and a ramped cycle ergometer test to exhaustion as a criterion measure for peak values (oxygen uptake and heart rate...

Active Drumming Experience Increases Infants' Sensitivity to Audiovisual Synchrony during Observed Drumming Actions.

Directory of Open Access Journals (Sweden)

Sarah A Gerson

Full Text Available In the current study, we examined the role of active experience on sensitivity to multisensory synchrony in six-month-old infants in a musical context. In the first of two experiments, we trained infants to produce a novel multimodal effect (i.e., a drum beat and assessed the effects of this training, relative to no training, on their later perception of the synchrony between audio and visual presentation of the drumming action. In a second experiment, we then contrasted this active experience with the observation of drumming in order to test whether observation of the audiovisual effect was as effective for sensitivity to multimodal synchrony as active experience. Our results indicated that active experience provided a unique benefit above and beyond observational experience, providing insights on the embodied roots of (early music perception and cognition.

Active Drumming Experience Increases Infants’ Sensitivity to Audiovisual Synchrony during Observed Drumming Actions

Science.gov (United States)

Timmers, Renee; Hunnius, Sabine

2015-01-01

In the current study, we examined the role of active experience on sensitivity to multisensory synchrony in six-month-old infants in a musical context. In the first of two experiments, we trained infants to produce a novel multimodal effect (i.e., a drum beat) and assessed the effects of this training, relative to no training, on their later perception of the synchrony between audio and visual presentation of the drumming action. In a second experiment, we then contrasted this active experience with the observation of drumming in order to test whether observation of the audiovisual effect was as effective for sensitivity to multimodal synchrony as active experience. Our results indicated that active experience provided a unique benefit above and beyond observational experience, providing insights on the embodied roots of (early) music perception and cognition. PMID:26111226

Rotary drum for distilling bituminous material

Energy Technology Data Exchange (ETDEWEB)

1921-11-02

A rotary drum with insert tubes for distilling bituminous materials, like mineral coal, brown coal, wood, peat, and oil-shale, is characterized in that the insert tube is heated also by superheated steam introduced into the drum.

DRUM DRYER FOR DRYING THE PARTICULATE PRODUCTS

Directory of Open Access Journals (Sweden)

I. S. Iurova

2014-01-01

Full Text Available Summary. For raise effectiveness drying process drum-type installation in which drum the mechanism of creation of various zones providing a necessary temperature and hydrodynamic regime of process of drying in process of product passage on a drum and changes in it of a relationship of various forms of communication of a moisture, and also a process intensification at last stage of drying by creation разряжения in a continuous technological stream of drying is provided is offered. The drum provides formation of a zone of separation of heat-transfer agent by means of the dissector, zones of intensive drying by disposing lobate nozzles in chessboard order with a dividing ring, zones of separation of the completed heat-transfer agent from жома as a result of separator installation in which the elliptic disk having cuts on a straight line from edge to the centre places, with formation of the triangular slot for passage dried pulp and heat-transfer agent, and also zones the final drying by performance of a section of a drum matching to a zone perforated on which length are had spring-loaded lobate nozzles representing the blades connected bow-shaped rod with metal plates, had with outer side of a drum and under the form repeating its contour, thus the bow-shaped rod from the interior of a drum which ends are supplied by springs rest against overhead and bottom persistent screw nuts, and blades and metal plates are installed with possibility of twirl concerning a fastening place on a drum and supplied by reinforcing ribs.

Infrared thermography applied to monitoring of radioactive waste drums

International Nuclear Information System (INIS)

Kelmer, P.; Camarano, D.M.; Calado, F.; Phillip, B.; Viana, C.; Andrade, R.M.

2013-01-01

The use of thermography in the inspection of drums containing radioactive waste is being stimulated by the absence of physical contact. In Brazil the majority of radioactive wastes are compacted solids packed in metal drums stored temporarily for decades and requires special attention. These drums have only one qualitative indication of the radionuclides present. However, its structural condition is not followed systematically. The aim of this work is presents a methodology by applying thermography for monitoring the structural condition of drums containing radioactive waste in order to detect degraded regions of the drums. (author)

21 CFR 886.4230 - Ophthalmic knife test drum.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Ophthalmic knife test drum. 886.4230 Section 886...) MEDICAL DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4230 Ophthalmic knife test drum. (a) Identification. An ophthalmic knife test drum is a device intended to test the keenness of ophthalmic surgical...

Noble Gases

Science.gov (United States)

Podosek, F. A.

2003-12-01

The noble gases are the group of elements - helium, neon, argon, krypton, xenon - in the rightmost column of the periodic table of the elements, those which have "filled" outermost shells of electrons (two for helium, eight for the others). This configuration of electrons results in a neutral atom that has relatively low electron affinity and relatively high ionization energy. In consequence, in most natural circumstances these elements do not form chemical compounds, whence they are called "noble." Similarly, much more so than other elements in most circumstances, they partition strongly into a gas phase (as monatomic gas), so that they are called the "noble gases" (also, "inert gases"). (It should be noted, of course, that there is a sixth noble gas, radon, but all isotopes of radon are radioactive, with maximum half-life a few days, so that radon occurs in nature only because of recent production in the U-Th decay chains. The factors that govern the distribution of radon isotopes are thus quite different from those for the five gases cited. There are interesting stories about radon, but they are very different from those about the first five noble gases, and are thus outside the scope of this chapter.)In the nuclear fires in which the elements are forged, the creation and destruction of a given nuclear species depends on its nuclear properties, not on whether it will have a filled outermost shell when things cool off and nuclei begin to gather electrons. The numerology of nuclear physics is different from that of chemistry, so that in the cosmos at large there is nothing systematically special about the abundances of the noble gases as compared to other elements. We live in a very nonrepresentative part of the cosmos, however. As is discussed elsewhere in this volume, the outstanding generalization about the geo-/cosmochemistry of the terrestrial planets is that at some point thermodynamic conditions dictated phase separation of solids from gases, and that the

Modeling unsteady-state VOC transport in simulated waste drums

International Nuclear Information System (INIS)

Liekhus, K.J.; Gresham, G.L.; Peterson, E.S.; Rae, C.; Hotz, N.J.; Connolly, M.J.

1994-01-01

This report is a revision of an EG ampersand G Idaho informal report originally titled Modeling VOC Transport in Simulated Waste Drums. A volatile organic compound (VOC) transport model has been developed to describe unsteady-state VOC permeation and diffusion within a waste drum. Model equations account for three primary mechanisms for VOC transport from a void volume within the drum. These mechanisms are VOC permeation across a polymer boundary, VOC diffusion across an opening in a volume boundary, and VOC solubilization in a polymer boundary. A series of lab-scale experiments was performed in which the VOC concentration was measured in simulated waste drums under different conditions. A lab-scale simulated waste drum consisted of a sized-down 55-gal metal drum containing a modified rigid polyethylene drum liner. Four polyethylene bags were sealed inside a large polyethylene bag, supported by a wire cage, and placed inside the drum liner. The small bags were filled with VOC-air gas mixture and the VOC concentration was measured throughout the drum over a period of time. Test variables included the type of VOC-air gas mixtures introduced into the small bags, the small bag closure type, and the presence or absence of a variable external heat source. Model results were calculated for those trials where the permeability had been measured

Heat load limits for TRU drums on pads

International Nuclear Information System (INIS)

Steimke, J.L.; McKinley, M.S.

1993-08-01

Some of the Trans-Uranic (TRU) waste generated at SRS is packaged in 55 gallon, galvanized steel drums and stored on concrete pads that are exposed to the weather. It was necessary to compute how much heat can be generated by the waste in these drums without exceeding the temperature limits of the contents of the drum. This report documents the calculation of heat load limits for the drum, which depend on the temperature limits of the contents of the drum. The applicable temperature limits for the contents of the drum are the melting temperature of the polyethylene liner, 284 ± 8 F, the combustion temperature of paper, 450 F and the decomposition temperature of anionic resin, 190 F. One part of the analysis leading to the heat load limits was the collection of weather records on solar flux, wind speed and air temperature. Another part of the task was an experimental measurement of two important properties of the drum lid, the emittance and the absorptance. As used here, emittance is the rate at which an object emits infrared thermal radiation divided by the rate at which a perfect black body at the same temperature emits thermal radiation. Absorptance is the rate at which an object absorbs solar radiation divided by the rate at which a perfect black body absorbs radiation. For nine locations on each of eight typical weathered drum lids the measured emittance ranged from 0.73 ± 0.05 to 1.00 ± 0.07 (95% confidence level) and the average emittance for the eight lids was 0.85. For the eight drum lids the measured absorptance ranged from 0.64 ± 0.07 to 0.79 ± 0.07 with an average absorptance for the eight lids of 0.739

Rotary drum for a centrifugal separator

International Nuclear Information System (INIS)

Fukai, Tamotsu.

1970-01-01

Herein provided is a rotary drum designed to prevent strength reduction and eccentric weight redistribution at the joints between the drum body and the end cups therefore when materials having divergent specific gravities, strengths and Young's Modulus are employed as the construction materials for the drum body and end cups. The drum body is fabricated by combining glass, carbon boron or similar high strength fibers with a thermosetting hardenable resin. This composite material is then molded into the finished cylindrical product the ends of which are bent slightly inward to receive a rigid, high-strength, ring-shaped end fitting to be integrally joined thereto during the molding operation. Each ring is further adapted to retain an end cap by a procedure which entails lowering the temperature of the end cap and applying heat to the ring, thus joining both members tightly together by employing the differences in thermal expansion of each. (Owens, K. J.)

Method of estimating maximum VOC concentration in void volume of vented waste drums using limited sampling data: Application in transuranic waste drums

International Nuclear Information System (INIS)

Liekhus, K.J.; Connolly, M.J.

1995-01-01

A test program has been conducted at the Idaho National Engineering Laboratory to demonstrate that the concentration of volatile organic compounds (VOCs) within the innermost layer of confinement in a vented waste drum can be estimated using a model incorporating diffusion and permeation transport principles as well as limited waste drum sampling data. The model consists of a series of material balance equations describing steady-state VOC transport from each distinct void volume in the drum. The primary model input is the measured drum headspace VOC concentration. Model parameters are determined or estimated based on available process knowledge. The model effectiveness in estimating VOC concentration in the headspace of the innermost layer of confinement was examined for vented waste drums containing different waste types and configurations. This paper summarizes the experimental measurements and model predictions in vented transuranic waste drums containing solidified sludges and solid waste

Examination of representative drum from 618-9 Burial Ground

International Nuclear Information System (INIS)

Duncan, D.R.; Bunnell, L.R.

1992-10-01

The work described in this report was conducted in pursuance of Task E of the Pacific Northwest Laboratory Solid Waste Technology Support Program for Westinghouse Hanford Company. Task E calls for a determination of the corrosion rate of low-carbon steels under typical Hanford Site conditions. To meet this objective, Pacific Northwest Laboratory examined one intact drum that was judged to be representative of the largely intact drums excavated at the 618-9 Burial Ground located west of the 300 Area at the Hanford Site. Six samples were examined to characterize the drum, its composition, and its corrosion and corrosion products. The drum, which was found empty, was constructed of low-carbon steel. Its surface appeared relatively sound. The drum metal varied in thickness, but the minimum thickness in the samples was near 0.020 in. The corrosion corresponds to approximately 25 to 35 mils of metal loss, roughly a 1 mil/yr corrosion rate. Corrosion products were goethite and maghymite, expected products of iron buried in soil. Apparently, the drum leaked some time ago, but the cause of the leakage is unknown because records of the drums and their burial are limited. The drum was empty when found, and it is possible that it could have failed by pitting rather than by general corrosion. A pitting rate of about 3.5 mils/yr would have caused loss of drum integrity in the time since burial

Case studies of corrosion of mixed waste and transuranic waste drums

International Nuclear Information System (INIS)

Kosiewicz, S.T.

1993-01-01

This paper presents three case studies of corrosion of waste drums at the Los Alamos National Laboratory (LANL). Corrosion was not anticipated by the waste generators, but occurred because of subtle chemical or physical mechanisms. In one case, drums of a cemented transuranic (TRU) sludge experienced general and pitting corrosion. In the second instance, a chemical from a commercial paint stripper migrated from its primary containment drums to chemically attack overpack drums made of mild carbon steel. In the third case, drums of mixed low level waste (MLLW) soil corroded drum packaging even though the waste appeared to be dry when it was placed in the drums. These case studies are jointly discussed as ''lessons learned'' to enhance awareness of subtle mechanisms that can contribute to the corrosion of radioactive waste drums during interim storage

The Saami shaman drums: some reflexions from an archaelogical perspective

Directory of Open Access Journals (Sweden)

Inger Zachrisson

1991-01-01

Full Text Available The Saami shaman drums from northern Scandinavia can be discussed from many different points of view. For an archaeologist there are other questions of interest than those which generally occupy the historian of religions. One important question is how old the known Saami drums are. The known drums are as a rule assumed to be from the seventeenth or the eighteenth centuries, when most of them were collected. It has also been thought that, because of the materials they are made of, drums could not have been preserved any longer. Another perhaps more interesting question is how old the known types of Saami drums might be. When did they acquire their 'classical' form? What did the Viking Age Saami drums look like?

The Saami shaman's drum and the star horizons

Directory of Open Access Journals (Sweden)

Bo Sommarström

1991-01-01

Full Text Available The aim of this contribution is to examine the possible influences of stellar constellations on the positioning of the drum figures on the drums used by the Saami people during the 17th and 18th centuries. Certain of the drum figures seem to have a similar position to corresponding figures on traditional star maps, both with respect to single star constellations and to some members of the Zodiac circle. The most general correspondences between star maps and the painted designs on drums depend on the existence of a cross for determining the four cardinal points in both cases. The star constellations compared here with the drum-figures are in fact peripheral Saami skies. It is hard to believe that they can have played any vital role in their capacity as star symbols within the frame of the Saamis' own astral cosmology. It is more probable that the earthly meanings of most of the figures were more important to the drummer.

Safety analysis report for packaging (onsite) steel drum

International Nuclear Information System (INIS)

McCormick, W.A.

1998-01-01

This Safety Analysis Report for Packaging (SARP) provides the analyses and evaluations necessary to demonstrate that the steel drum packaging system meets the transportation safety requirements of HNF-PRO-154, Responsibilities and Procedures for all Hazardous Material Shipments, for an onsite packaging containing Type B quantities of solid and liquid radioactive materials. The basic component of the steel drum packaging system is the 208 L (55-gal) steel drum

An improved segmented gamma scanning for radioactive waste drums

International Nuclear Information System (INIS)

Liu Cheng; Wang Dezhong; Bai Yunfei; Qian Nan

2010-01-01

In this paper, the equivalent radius of radioactive sources in each segment is determined by analyzing the different responses of the two identical detectors, and an improved segmented gamma scanning is used to assay waste drums containing mainly organic materials, and proved by an established simulation model. The simulated radioactivity distributions in homogenous waste drum and an experimental heterogeneous waste drum were compared with those of traditional segmented gamma scanning. The results show that our method is good in performance and can be used for analyzing the waste drums. (authors)

Rotary drum dryers for coal slurries

Energy Technology Data Exchange (ETDEWEB)

Baunack, F

1983-04-01

The suitability, sizing and internal equipment of rotary drum dryers for high-ash coal slurries are discussed. Rotary dryers will handle also difficult slurries; by suitable drum sizes, lifter blades and chains not only high specific evaporation capacities can be achieved but also very high throughputs of up to 400 tons/h of finished product and high evaporation capacities of 60 tons/h.

Noble Gases in Lakes and Ground Waters

OpenAIRE

Kipfer, Rolf; Aeschbach-Hertig, Werner; Peeters, Frank; Stute, Marvin

2002-01-01

In contrast to most other fields of noble gas geochemistry that mostly regard atmospheric noble gases as 'contamination,' air-derived noble gases make up the far largest and hence most important contribution to the noble gas abundance in meteoric waters, such as lakes and ground waters. Atmospheric noble gases enter the meteoric water cycle by gas partitioning during air / water exchange with the atmosphere. In lakes and oceans noble gases are exchanged with the free atmosphere at the surface...

Source imaging of drums in the APNEA system

International Nuclear Information System (INIS)

Hensley, D.

1995-01-01

The APNea System is a neutron assay device utilizing both a passive mode and a differential-dieaway active mode. The total detection efficiency is not spatially uniform, even for an empty chamber, and a drum matrix in the chamber can severely distort this response. In order to achieve a response which is independent of the way the source material is distributed in a drum, an imaging procedure has been developed which treats the drum as a number of virtual (sub)volumes. Since each virtual volume of source material is weighted with the appropriate instrument parameters (detection efficiency and thermal flux), the final assay result is essentially independent of the actual distribution of the source material throughout the drum and its matrix

Waste streams that preferentially corrode 55-gallon steel storage drums

International Nuclear Information System (INIS)

Zirker, L.R.; Beitel, G.A.; Reece, C.M.

1995-06-01

When 55-gal steel drum waste containers fail in service, i.e., leak, corrode or breach, the standard fix has been to overpack the drum. When a drum fails and is overpacked into an 83-gal overpack drum, there are several negative consequences. Identifying waste streams that preferentially corrode steel drums is essential to the pollution prevention philosophy that ''an ounce of prevention is worth a pound of cure.'' It is essential that facilities perform pollution prevention measures at the front end of processes to reduce pollution on the back end. If these waste streams can be identified before they are packaged, the initial drum packaging system could be fortified or increased to eliminate future drum failures, breaches, clean-ups, and the plethora of other consequences. Therefore, a survey was conducted throughout the US Department of Energy complex for information concerning waste streams that have demonstrated preferential corrosion of 55-gal steel drums. From 21 site contacts, 21 waste streams were so identified. The major components of these waste streams include acids, salts, and solvent liquids, sludges, and still bottoms. The solvent-based waste streams typically had the shortest time to failure, 0.5 to 2 years. This report provides the results of this survey and research

Listening to the Shape of a Drum

Indian Academy of Sciences (India)

Home; Journals; Resonance – Journal of Science Education; Volume 3; Issue 9. Listening to the Shape of a Drum - The Mathematics of Vibrating Drums. S Kesavan. General Article Volume 3 Issue 9 September 1998 pp 26-34. Fulltext. Click here to view fulltext PDF. Permanent link:

Fire propagation through arrays of solid-waste storage drums

International Nuclear Information System (INIS)

Smith, S.T.; Hinkle, A.W.

1995-01-01

The extent of propagation of a fire through drums of solid waste has been an unresolved issue that affects all solid-waste projects and existing solid-waste storage and handling facilities at the Hanford site. The issue involves the question of how many drums of solid waste within a given fire area will be consumed in a design-basis fire for given parameters such as drum loading, storage arrays, initiating events, and facility design. If the assumption that all drums of waste within a given fire area are consumed proves valid, then the construction costs of solid waste facilities may be significantly increased

Listening to the Shape of a Drum

Indian Academy of Sciences (India)

Home; Journals; Resonance – Journal of Science Education; Volume 3; Issue 10. Listening to the Shape of a Drum - You Cannot Hear the Shape of a Drum! S Kesavan. General Article Volume 3 Issue 10 October 1998 pp 49-58. Fulltext. Click here to view fulltext PDF. Permanent link:

Hydrogen explosion testing with a simulated transuranic drum

International Nuclear Information System (INIS)

Dykes, K.L.; Meyer, M.L.

1990-01-01

Transuranic (TRU) waste generated at the Savannah River Site (SRS) is currently stored onsite for future retrieval and permanent disposal at the Waste Isolation Pilot Plant (WIPP). Some of the TRU waste is stored in vented 210-liter (55-gallon) drums and consists of gloves, wipes, plastic valves, tools, etc. Gas generation caused by radiolysis and biodegradation of these organic waste materials may produce a flammable hydrogen-air mixture (>4% v/v) in the multi-layer plastic waste bags. Using a worst case scenario, a drum explosion test program was carried out to determine the hydrogen concentration necessary to cause removal of the drum lid. Test results indicate an explosive mixture up to 15% v/v of hydrogen can be contained in an SRS TRU drum without total integrity failure via lid removal

Fatigue behaviour of coke drum materials under thermal-mechanical cyclic loading

Directory of Open Access Journals (Sweden)

Jie Chen

2014-01-01

Full Text Available Coke drums are vertical pressure vessels used in the delayed coking process in petroleum refineries. Significant temperature variation during the delayed coking process causes damage in coke drums in the form of bulging and cracking. There were some studies on the fatigue life estimation for the coke drums, but most of them were based on strain-fatigue life curves at constant temperatures, which do not consider simultaneous cyclic temperature and mechanical loading conditions. In this study, a fatigue testing system is successfully developed to allow performing thermal-mechanical fatigue (TMF test similar to the coke drum loading condition. Two commonly used base and one clad materials of coke drums are then experimentally investigated. In addition, a comparative study between isothermal and TMF lives of these materials is conducted. The experimental findings lead to better understanding of the damage mechanisms occurring in coke drums and more accurate prediction of fatigue life of coke drum materials.

The aesthetic interpretation on Wooden Drum Dancing of Wa people

Directory of Open Access Journals (Sweden)

Youfeng Wang

2017-02-01

Full Text Available The Wa nationality, a typical ethnic group in Yunnan province, is an ancient one lives across Yunnan. The main residences of it are border area beside northern Yunnan and the Wa States in Burma. Among all the Wa dances, Wooden Drum Dancing leads a vital position, and it is also a symbolic dancing in the culture of Wa people. The feature of Wooden Drum Dancing is that every action expending by the beats of wooden drum, namely, first the wooden drum, then the Wooden Drum Dancing. Dancing is an important content in the life of Wa people, and the aesthetics of life comes from dancing, so they present their value on worship by the form of dancing. This article is going to interpret the aesthetic standard on Wa people’s Wooden Drum Dancing by the view of aesthetics, and come into a conclude that the inspiration of such dancing came from practice and their worship to nature and ancestor. The Wooden Drum Dancing displays totally the tough air and solidarity of Wa people, which also presents the fair society of them. The Wooden Drum Dancing is an enriched art that Wa People took from particle life, so dancing of Wa is often classified into the aesthetic area of plain. The information of people’s living situation displayed by Wa dancing also conveys their rich emotions. The sense of beauty within Wooden Drum Dancing will give others a solemn feeling. The formal beauty is displayed by the rhythm of upper part of body, and the power beauty is displayed by the rhythm of the lower part of body.

7 CFR 1434.8 - Containers and drums.

Science.gov (United States)

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false Containers and drums. 1434.8 Section 1434.8... REGULATIONS FOR HONEY § 1434.8 Containers and drums. (a)(1) To be eligible for assistance under this part, honey must be packed in: (i) CCC-approved, 5-gallon plastic containers; (ii) 5-gallon metal containers...

Verification calculation of drum and pulley overhead travelling crane on gamma irradiators

International Nuclear Information System (INIS)

Syamsurrijal Ramdja; Ari Satmoko; Sutomo Budihardjo

2010-01-01

Having verified the calculation of dam drum pulleys found on cranes to facilitate the gamma irradiator. Drum is a device for rolling steel ropes while the pulley is a circular pieces called disks, which are made from metal or non-metal to transmit motion and force. Having verified calculation of forces acting style on drums, drum diameter and length and style of press that occurred on drums. Likewise, the pulley, pulley diameter verified calculations, measures of disc and shaft power pulleys. From the verification results will be obtained whether the data drums and pulley device is safe or not safe to use. (author)

Direct measurement of γ-emitting radionuclides in waste drum

International Nuclear Information System (INIS)

Ma Ruwei; Mao Yong; Zhang Xiuzhen; Xia Xiaobin; Guo Caiping; Han Yueqin

1993-01-01

The low-level rad waste produced from nuclear power plant, nuclear facilities, and in the process of their decommissioning is stored in waste depository. For the safety of transport and storage of these wastes, some test must be done. One of them is to analyse the kinds and activities of radionuclides in each waste drum. Segmented scanning gamma spectrum analysis can be used for direct measurement of gamma-emitting radionuclides in drum. Gamma emitters such as Co-60, Cs-137, Ra-226 can be measured directly from outside of drum. A method and system for direct measuring gamma emitters in waste drum are described, and measuring apparatus and measurement results as well

Noble gases in common rocks and their bearing on noble gas occurrences in the hydrological cycle

International Nuclear Information System (INIS)

Mazor, E.

1978-10-01

The comparison of the noble gases contents in different rocks and in thermal and cold water sources in the French Massif Central was aimed to define the amounts and nature of noble gases contributed by country rocks as opposed to atmospheric noble gases brought in by recharged water. No difference in the noble gas contents was found between waters coming in igneous rocks to those issuing in sedimentary rocks. In both, significant variations in the contents of atmospheric and radiogenic noble gases were found. Radiogenic helium has been found to reveal a positive correlation to the contents of atmospheric Ne, Ar, Kr. This indicates water recharge into the deep part of the systems, mixing with radiogenic He and Ar flushed from igneous and sedimentary rocks and subsequent partial gas loss. Loss of gas is evident from the observed low noble gas contents. These losses have been accompanied by a reversed retention pattern of Ne, Ar, Xc. This reversed retention pattern cannot be an artifact of sampling as well as cannot result by partial steam loss. A similar interpretation for the observed noble gas depletions that agrees with the fact that the observed fractionation patterns are not ''normal'' is given by deuterium and oxygen-18. The stable isotope data seem to exclude partial steam losses

Los Alamos waste drum shufflers users manual

International Nuclear Information System (INIS)

Rinard, P.M.; Adams, E.L.; Painter, J.

1993-01-01

This user manual describes the Los Alamos waste drum shufflers. The primary purpose of the instruments is to assay the mass of 235 U (or other fissile materials) in drums of assorted waste. It can perform passive assays for isotopes that spontaneously emit neutrons or active assays using the shuffler technique as described on this manual

JUSTIFICATION FOR A LIMIT OF 15 PERCENT HYDROGEN IN A 55-GALLON DRUM

International Nuclear Information System (INIS)

MARUSICH, R.M.

2007-01-01

The concentration of 15% hydrogen in air in a waste drum is used as the concentration at which the drum remains intact in the case of a deflagration. The following describes what could happen to the drum if 15% hydrogen or more in air were ignited. Table 2 of the Savannah River report WSRC-TR-90-165 ''TRU Drum Hydrogen Explosion Tests'' provides the results of tests performed in 55-gallon drums filled with hydrogen and air mixtures. The hydrogen-air mixtures were ignited by a hot-wire igniter. The results of the tests are shown in Table 1. They concluded that drums can withstand deflagration involving hydrogen concentration up to 15% hydrogen. Testing was performed at Idaho Falls and documented in a letter from RH Beers, Waste Technology Programs Division, EG and G Idaho, to CP Gertz, Radioactive Waste Technology Branch, DOE dated Sept. 29, 1983. In these tests, 55-gallon drums were filled with hydrogen-air mixtures which were ignited. The results in Table 2.2 showed that ignition for drums containing 11% and 14% hydrogen, the drum lid remained on the drum. Ignition in drum with 30% hydrogen resulted in lid loss. It is concluded from the results of these two tests that, for uncorroded drums, a 15% hydrogen in air mixture will not result in loss of drum integrity (i.e., lid remains on, walls remain intact). The drum walls however, may be thinned due to corrosion. The effect of the deflagration on thinner walls is assessed next. Assume a 15% hydrogen in air mixture exists in a drum. The pressure assuming adiabatic isochoric complete combustion (AICC) conditions is 69 psig (using the same deflagration pressure calculation method as in HNF-19492, ''Revised Hydrogen Deflagration Analysis which got 82 psig for 20% hydrogen in air)

A59 Drum Activity database (DRUMAC): system documentation

International Nuclear Information System (INIS)

Keel, Alan.

1993-01-01

This paper sets out the requirements, database design, software module designs and test plans for DRUMAC (the Active handling Building Drum Activity Database) - a computer-based system to record the radiological inventory for LLW/ILW drums dispatched from the Active Handling Building. (author)

Evaluation of X-ray System for Nondestructive Testing on Radioactive Waste Drums

International Nuclear Information System (INIS)

Park, Jong Kil; Maeng, Seong Jun; Lee, Yeon Ee; Hwang, Tae Won

2008-01-01

The physical and chemical properties of radioactive waste drums, which have been temporarily stored on site, should be characterized before their shipment to a disposal facility in order to prove that the properties meet the acceptance guideline. The investigation of NDT(Nondestructive Test) method was figured out that the contents in drum, the quantitative analysis of free standing water and void fraction can be examined with X-ray NDT techniques. This paper describes the characteristics of X-ray NDT such as its principles, the considerations for selection of X-ray system, etc. And then, the waste drum characteristics such as drum type and dimension, contents in drum, etc. were examined, which are necessary to estimate the optimal X-ray energy for NDT of a drum. The estimation results were that: the proper X-ray energy is under 3 MeV to test the drums of 320 β and less; both X-ray systems of 450 keV and/or 3 MeV might be needed considering the economical efficiency and the realization. The number of drums that can be tested with 450 keV and 3 MeV X-ray system was figured out as 42,327 and 18,105 drums (based on storage of 2006. 12), respectively. Four testing scenarios were derived considering equipment procurement method, outsourcing or not, etc. The economical and feasibility assessment for the scenarios was resulted in that an optimal scenario is dependent on the acceptance guide line, the waste generator's policy on the waste treatment and the delivery to a disposal facility, etc. For example, it might be desirable that a waste generator purchases two 450 keV mobile system to examine the drums containing low density waste, and that outsourcing examination for the high density drums, if all NDT items such as quantitative analysis for 'free standing water' and 'void fraction', and confirmation of contents in drum have to be characterized. However, one 450 keV mobile system seems to be required to test only the contents in 13,000 drums per year.

Chimpanzee drumming : a spontaneous performance with characteristics of human musical drumming

NARCIS (Netherlands)

Dufour, Valerie; Poulin, Nicolas; Cure, Charlotte; Sterck, Elisabeth H. M.

2015-01-01

Despite the quintessential role that music plays in human societies by enabling us to release and share emotions with others, traces of its evolutionary origins in other species remain scarce. Drumming like humans whilst producing music is practically unheard of in our most closely related species,

Nonlinear vibrations analysis of rotating drum-disk coupling structure

Science.gov (United States)

Chaofeng, Li; Boqing, Miao; Qiansheng, Tang; Chenyang, Xi; Bangchun, Wen

2018-04-01

A dynamic model of a coupled rotating drum-disk system with elastic support is developed in this paper. By considering the effects of centrifugal and Coriolis forces as well as rotation-induced hoop stress, the governing differential equation of the drum-disk is derived by Donnell's shell theory. The nonlinear amplitude-frequency characteristics of coupled structure are studied. The results indicate that the natural characteristics of the coupling structure are sensitive to the supporting stiffness of the disk, and the sensitive range is affected by rotating speeds. The circumferential wave numbers can affect the characteristics of the drum-disk structure. If the circumferential wave number n = 1 , the vibration response of the drum keeps a stable value under an unbalanced load of the disk, there is no coupling effect if n ≠ 1 . Under the excitation, the nonlinear hardening characteristics of the forward traveling wave are more evident than that of the backward traveling wave. Moreover, because of the coupling effect of the drum and the disk, the supporting stiffness of the disk has certain effect on the nonlinear characteristics of the forward and backward traveling waves. In addition, small length-radius and thickness-radius ratios have a significant effect on the nonlinear characteristics of the coupled structure, which means nonlinear shell theory should be adopted to design rotating drum's parameter for its specific structural parameters.

Simulating Lahars Using A Rotating Drum

Science.gov (United States)

Neather, Adam; Lube, Gert; Jones, Jim; Cronin, Shane

2014-05-01

A large (0.5 m in diameter, 0.15 m wide) rotating drum is used to investigate the erosion and deposition mechanics of lahars. To systematically simulate the conditions occurring in natural mass flows our experimental setup differs from the common rotating drum employed in industrial/engineering studies. Natural materials with their typical friction properties are used, as opposed to the frequently employed spherical glass beads; the drum is completely water-proof, so solid/air and solid/liquid mixtures can be investigated; the drum velocity and acceleration can be precisely controlled using a software interface to a micro-controller, allowing for the study of steady, unsteady and intermediate flow regimes. The drum has a toughened glass door, allowing high-resolution, high-speed video recording of the material inside. Vector maps of the velocities involved in the flows are obtained using particle image velocimetry (PIV). The changes in velocity direction and/or magnitude are used to locate the primary internal boundaries between layers of opposite flow direction, as well as secondary interfaces between shear layers. A range of variables can be measured: thickness and number of layers; the curvature of the free surface; frequency of avalanching; position of the centre of mass of the material; and the velocity profiles of the flowing material. Experiments to date have focussed on dry materials, and have had a fill factor of approximately 0.3. Combining these measured variables allows us to derive additional data of interest, such as mass and momentum flux. It is these fluxes that we propose will allow insight into the erosion/deposition mechanics of a lahar. A number of conclusions can be drawn to date. A primary interface separates flowing and passive region (this interface has been identified in previous studies). As well as the primary interface, the flowing layer separates into individual shear layers, with individual erosion/deposition and flow histories. This

Characterization of In-Drum Drying Products

International Nuclear Information System (INIS)

Kroselj, V.; Jankovic, M.; Skanata, D.; Medakovic, S.; Harapin, D.; Hertl, B.

2006-01-01

A few years ago Krsko NPP decided to introduce In-Drum Drying technology for treatment and conditioning of evaporator concentrates and spent ion resins. The main reason to employ this technology was the need for waste volume reduction and experience with vermiculite-cement solidification that proved inadequate for Krsko NPP. Use of In-Drum Drying technology was encouraged by good experience in the field at some German and Spanish NPP's. In the paper, solidification techniques in vermiculite-cement matrix and In-Drum Drying System are described briefly. The resulting waste forms (so called solidification and dryer products) and containers that are used for interim storage of these wastes are described as well. A comparison of the drying versus solidification technology is performed and advantages as well as disadvantages are underlined. Experience gained during seven years of system operation has shown that crying technology resulted in volume reduction by factor of 20 for evaporator concentrates, and by factor of 5 for spent ion resin. Special consideration is paid to the characterization of dryer products. For evaporator concentrates the resulting waste form is a solid salt block with up to 5% bound water. It is packaged in stainless steel drums (net volume of 200 l) with bolted lids and lifting rings. The fluidized spent ion resins (primary and blow-down) are sluiced into the spent resin drying tank. The resin is dewatered and dried by electrical jacket heaters. The resulting waste (i.e. fine granulates) is directly discharged into a shielded stainless steel drum with bolted lid and lifting rings. Characterization of both waste forms has been performed in accordance with recommendations given in Characterization of Radioactive Waste Forms and Packages issued by International Atomic Energy Agency, 1997. This means that radiological, chemical, physical, mechanical, biological and thermal properties of the waste form has been taken into consideration. In the paper

RATIONALE FOR CENTERING CAPACITY OF REDISIGNED BELT CONVEYOR DRUMS

Directory of Open Access Journals (Sweden)

V. V. Suglobov

2016-02-01

Full Text Available Purpose. In the study is necessary: 1 to justify aligning drums of a new design of belt conveyors; 2 to develop a method for calculating and determining the rational design parameters of drums depending on the technical parameters of the conveyor belt (the length of the conveyor, belt width, the performance of the conveyor, the diameter of the drive and tension drums, etc.; 3 to carry out pilot studies of efficiency conveyor belt in a production environment in order to determine the magnitude of dynamic loads and a comparative evaluation of the effectiveness of the centering ability of conventional and new designs of drums. Methodology. To substantiate the effectiveness of the centering ability of the drums of a new design by the authors developed a mathematical model of interaction of the tape with the drum. Mathematical simulation of tape reels with new design comes to drawing up a differential equation of the belt based on the dynamic component and restoring force. This model allowed us to estimate the movement of the tape in the transverse direction based on the calculated additional dynamic loads and forces on the investigated centering a conveyor belt with given specifications. For the first time the technique of calculating and determining the rational parameters of the drums, which allows determining the design parameters of the centering portions, depending on the mechanical properties and geometric parameters of the tape. Findings. With the help of mathematical modeling the scientifically substantiated effect of centering the ability of the new design of the drum, which ensures stable tape running along the longitudinal axis of the conveyor. The authors made the following conclusions: 1 the mathematical model of interaction with the new belt design of the drum, which allowed to describe the belt in the transverse direction in view of additional dynamic loads and renewable power was developed; 2 the method of calculation and

Experimental investigation of rotating-drum separators for liquid-metal MHD applications

International Nuclear Information System (INIS)

Lenzo, C.S.; Dauzvardis, P.V.; Hantman, R.G.

1978-01-01

For the past several years, Argonne National Laboratory has been active in the development of closed-cycle two-phase-flow MHD power systems. One of the key components in such systems is an effective and efficient gas-liquid separator-diffuser. On the basis of an assessment of present technology, it was decided to study the characteristics of a rotating drum type of separator, and a multitask research and development program was initiated within the overall liquid-metal MHD research program. The first task, now completed, centered on the investigation of single-phase flow (liquid) deposited by a flow nozzle on the inner surface of freely-rotating cylinders or drums of 423 mm and 282 mm diam. The tests were designed to study the recovery of energy in the liquid layer deposited on the drum; the torque transmitted to the drum by the liquid as the result of shear stress between the liquid and the drum surface; the characteristics of the liquid layer; and the effects of drum size, nozzle shape and orientation, and nozzle velocity. The test results showed that a stable liquid film was formed on the drum and that the kinetic energy of the liquid layer was high enough to be potentially useful in two-phase-flow MHD power systems

Coke degradation by surface breakage in a modified tumble drum

Energy Technology Data Exchange (ETDEWEB)

Litster, J D

1987-01-01

The surface breakage rate constant for three Australian battery cokes was measured in a specially modified tumble drum using a previously developed technique. The effect of experimental test parameters - coke size, sample mass, drum speed, lifter height and lifter number - on the surface breakage rate constant was examined. The motion of coke particles within a tumble drum was filmed in a simulation experiment with a 0.31 m diameter drum. Particles were raised on the lifters, fell and collided with the bottom of the drum. These collisions were the main source of fines (minus 1 mm) production rather than true abrasion as depicted by a rubbing, rolling action. Hence the term 'surface breakage' is more appropriate than 'abrasion' to describe the breakage process. By measuring the volume of coke carried by each lifter and the height of fall of the coke, the effect of drum speed, sample mass, lifter height and number on the rate of surface breakage was successfully explained. The surface breakage rate constant was found to be proportional to particle size to the power 0.33 for the three cokes studied. A normalized surface breakage rate constant was derived which allowed comparison of cokes with different size distributions. This parameter characterises the coke surface breakage resistance.

Fire testing of 55 gallon metal waste drums for dry waste storage

International Nuclear Information System (INIS)

Hasegawa, H.K.; Staggs, K.J.; Doughty, S.M.

1993-07-01

The primary goal of this test program was to conduct a series of fire test to provide information on the fire performance of 55 gallon metal waste drums used for solid waste disposal at Department Of Energy (DOE) facilities. This program was limited in focus to three different types of 55 gallon drums, one radiant heat source, and one specific fire size. The initial test was a single empty 55 gallon drum exposed to a standard ASTME-119 time temperature curve for over 10 minutes. The full scale tests involved metal drums exposed to a 6' diameter flammable liquid fire for a prescribed period of time. The drums contained simulated dry waste materials of primarily class A combustibles. The test results showed that a conventional 55 gallon drum with a 1in. bung would blow its lid consistently

Noble gas magnetic resonator

Science.gov (United States)

Walker, Thad Gilbert; Lancor, Brian Robert; Wyllie, Robert

2014-04-15

Precise measurements of a precessional rate of noble gas in a magnetic field is obtained by constraining the time averaged direction of the spins of a stimulating alkali gas to lie in a plane transverse to the magnetic field. In this way, the magnetic field of the alkali gas does not provide a net contribution to the precessional rate of the noble gas.

Study on mechanics of driving drum with superelastic convexity surface covering-layer structure

Energy Technology Data Exchange (ETDEWEB)

Xiao, L.J.; Sui, X.H.; Miao, D.J. [Shandong University of Science & Technology, Qingdao (China)

2008-09-15

Belt conveyor is one of the main transport equipment in coal mine and the driving drum is its key part. With the method of bionic design, the mushroom morphological structure is applied to the design of covering-layer structure of driving drum surface of belt conveyor. Superelastic rubber with large deformation is adopted as the covering-layer material. Nonlinear constitutive model of rubber, which is of superelasticity and large deformation, is established. The stress states and deformation principles of driving drums including both bionic covering-layer and common covering-layer are obtained by static intensity analysis with Finite Element Analysis (FEA) software ANSYS. The values of the stress and strain on the driving drum surface are gotten and the dangerous area is determined. FEA results show that the superelastic convexity surface structure can enlarge the contact area between the driving drum and viscoelastic belt. The results also show that in comparison with common driving drum, the bionic surface driving drum can not only increase the friction coefficient between drum and belt but also prolong its service life.

Study of gas generation in drum L/ILW packages using hermetic containers

International Nuclear Information System (INIS)

Molnar, M.; Palcsu, L.; Svingor, E.; Futo, I.; Major, Z.; Veres, M.

2005-01-01

Complete text of publication follows. During the storage of low and intermediate level radioactive waste (L/ILW) significant quantities of gas may be produced. It is likely that a small proportion of the generated gas will be radioactive as a result of the incorporation of the isotopes 3 H and 14 C that are present within the waste. To obtain reliable estimates of the quantities and rates of the gas production in L/ILWa series of measurements was carried out of waste packages produced and temporarily stored at the site of Paks Nuclear Power Plant (NPP). Ten drums filled with selected original L/ILW were placed into hermetic containers equipped with sampling valves for repeated sampling. These hermetic containers were stored at the same site where the L/ILW is stored primarily in the Paks NPP. The pressure and the temperature of the headspace gas in the containers were monitored continuously. Qualitative gas component analyses of headspace gases of drums and their containers were executed by quadrupole mass spectrometer. The gas generation rate in the stored L/ILW was calculated by the measured state parameters and the composition variation of the gas in the closed containers. Stable isotope measurements were executed from the CO 2 , CH 4 and N 2 fractions by stable isotope ratio mass spectrometer. Helium measurements were done by noble gas mass spectrometer. The tritium content of the vapour, H 2 and CH 4 fractions was measured by a low background liquid scintillation counter. 14 C content of the CO 2 and CH 4 fractions was measured by a low background gas proportional counter system (ATOMKI). Our results showed that the main generated gases in L/ILW are carbon dioxide, methane, hydrogen and nitrogen. The typical rates were 0.05-0.2 normal litre gas/day for CO 2 and CH 4 generation, and less than 0.02 normal litre gas/day for H 2 . Because of the typical vanishing of the O 2 from the headspace gases no explosive gas mixture was indicated in the L/ILW drums during

Expected precision of neutron multiplicity measurements of waste drums

International Nuclear Information System (INIS)

Ensslin, N.; Krick, M.S.; Menlove, H.O.

1995-01-01

DOE facilities are beginning to apply passive neutron multiplicity counting techniques to the assay of plutonium scrap and residues. There is also considerable interest in applying this new measurement technique to 208-liter waste drums. The additional information available from multiplicity counting could flag the presence of shielding materials or improve assay accuracy by correcting for matrix effects such as (α,n) induced fission or detector efficiency variations. The potential for multiplicity analysis of waste drums, and the importance of better detector design, can be estimated by calculating the expected assay precision using a Figure of Merit code for assay variance. This paper reports results obtained as a function of waste drum content and detector characteristics. We find that multiplicity analysis of waste drums is feasible if a high-efficiency neutron counter is used. However, results are significantly poorer if the multiplicity analysis must be used to solve for detection efficiency

Re-evaluation of the 1995 Hanford Large Scale Drum Fire Test Results

International Nuclear Information System (INIS)

Yang, J M

2007-01-01

A large-scale drum performance test was conducted at the Hanford Site in June 1995, in which over one hundred (100) 55-gal drums in each of two storage configurations were subjected to severe fuel pool fires. The two storage configurations in the test were pallet storage and rack storage. The description and results of the large-scale drum test at the Hanford Site were reported in WHC-SD-WM-TRP-246, ''Solid Waste Drum Array Fire Performance,'' Rev. 0, 1995. This was one of the main references used to develop the analytical methodology to predict drum failures in WHC-SD-SQA-ANAL-501, 'Fire Protection Guide for Waste Drum Storage Array,'' September 1996. Three drum failure modes were observed from the test reported in WHC-SD-WM-TRP-246. They consisted of seal failure, lid warping, and catastrophic lid ejection. There was no discernible failure criterion that distinguished one failure mode from another. Hence, all three failure modes were treated equally for the purpose of determining the number of failed drums. General observations from the results of the test are as follows: (lg b ullet) Trash expulsion was negligible. (lg b ullet) Flame impingement was identified as the main cause for failure. (lg b ullet) The range of drum temperatures at failure was 600 C to 800 C. This is above the yield strength temperature for steel, approximately 540 C (1,000 F). (lg b ullet) The critical heat flux required for failure is above 45 kW/m 2 . (lg b ullet) Fire propagation from one drum to the next was not observed. The statistical evaluation of the test results using, for example, the student's t-distribution, will demonstrate that the failure criteria for TRU waste drums currently employed at nuclear facilities are very conservative relative to the large-scale test results. Hence, the safety analysis utilizing the general criteria described in the five bullets above will lead to a technically robust and defensible product that bounds the potential consequences from postulated

Remote radioactive waste drum inspection with an autonomous mobile robot

International Nuclear Information System (INIS)

Heckendorn, F.M.; Ward, C.R.; Wagner, D.G.

1992-01-01

An autonomous mobile robot is being developed to perform remote surveillance and inspection task on large numbers of stored radioactive waste drums. The robot will be self guided through narrow storage aisles and record the visual image of each viewable drum for subsequent off line analysis and archiving. The system will remove the personnel from potential exposure to radiation, perform the require inspections, and improve the ability to assess the long term trends in drum conditions

Application of artificial neural networks on the characterization of radioactive waste drums

International Nuclear Information System (INIS)

Potiens Junior, Ademar Jose; Hiromoto, Goro

2011-01-01

The methodology consist of system simulation of drum-detector by Monte Carlo for obtention of counting efficiency. The obtained data were treated and a neural artificial network (RNA) were constructed for evaluation of total activity of drum. For method evaluation measurements were performed in ten position parallel to the drum axis and the results submitted to the RNA. The developed methodology showed to be effective for isotopic characterization of gamma emitter radioactive wastes distributed in a heterogeneous way in a 200 litters drum. The objective of this work as to develop a methodology of analyse for quantification and localization of radionuclides not homogeneous distributed in a 200 liters drum based on the mathematical techniques

Noble gases solubility in water

International Nuclear Information System (INIS)

Crovetto, Rosa; Fernandez Prini, Roberto.

1980-07-01

The available experimental data of solubility of noble gases in water for temperatures smaller than 330 0 C have been critically surveyed. Due to the unique structure of the solvent, the solubility of noble gases in water decreases with temperature passing through a temperature of minimum solubility which is different for each gas, and then increases at higher temperatures. As aresult of the analysis of the experimental data and of the features of the solute-solvent interaction, a generalized equation is proposed which enables thecalculation of Henry's coefficient at different temperatures for all noble gases. (author) [es

Fatigue life estimation on coke drum due to cycle optimization

Science.gov (United States)

Siahaan, Andrey Stephan; Ambarita, Himsar; Kawai, Hideki; Daimaruya, Masashi

2018-04-01

In the last decade, due to the increasing demand of petroleum product, the necessity for converting the heavy oil are increasing. Thus, demand for installing coke drum in whole world will be increase. The coke drum undergoes the cyclic high temperature and suddenly cooling but in fact is not designed to withstand that kind of cycle, thus the operational life of coke drum is much shorter in comparison to other equipment in oil refinery. Various factors determine in order to improve reliability and minimize the down time, and it is found that the cycle optimization due to cycle, temperature, and pressure have an important role. From this research it is found that the fatigue life of the short cycle is decrease by a half compare to the normal cycle. It also found that in the preheating stage, the stress peak is far exceed the yield strength of coke drum material and fall into plastic deformation. This is happened because of the temperature leap in the preheating stage that cause thermal shock in the upper part of the skirt of the coke drum.

Recovery and use of fission product noble metals

International Nuclear Information System (INIS)

Jensen, G.A.; Rohmann, C.A.; Perrigo, L.D.

1980-06-01

Noble metals in fission products are of strategic value. Market prices for noble metals are rising more rapidly than recovery costs. A promising concept has been developed for recovery of noble metals from fission product waste. Although the assessment was made only for the three noble metal fission products (Rh, Pd, Ru), there are other fission products and actinides which have potential value

Experimental study of liquid carryover in a separator drum

International Nuclear Information System (INIS)

Prabhudharwadkar, Deoras M.; More, Rahul Z.; Iyer, Kannan N.

2010-01-01

The phenomenon of carryover, i.e. entrainment of liquid along with separated steam is observed in all the steam separators. Due to the risks, such as turbine blade erosion and radioactivity leakage, associated with it, it is desired to have an estimate of the carryover value. This is all the more important when the separation is only under the influence of gravity as proposed in some of the new generation natural circulation reactors. Experiments were carried out in an air-water facility at atmospheric conditions to characterize the entrainment in drums with ratio of the drum diameter to riser diameter varying from 1 to 6. Various parameters influencing the liquid entrainment were identified. The vapour superficial velocity and the drum diameter to riser diameter ratio were found to be the most influencing parameters. A dimensionless prediction correlation was evolved for the liquid entrainment and it was found to agree with previous works in the literature for drum to riser diameter ratio equal to 1.

Automation of a measurement systems of waste drum alpha activity

International Nuclear Information System (INIS)

Labarre, S.; Bardy, N.

1985-10-01

The alpha radiator activity in the two-hundred liter waste drums is found by an IN96, computerized analyzer of the society Intertechnique, from data delivered by a gamma detector (GeHP) and by neutron detection blocks (He counter). This computerized analyzer manages not only the drum rotation and position in front of the detector, but also the experimental data monitoring and their processing from specific programs (background noise, calibration, drum measurements). Thanks to this automation, the measurement number and their reliability are optimized [fr

Model air-supported drum-type homopolar generator

International Nuclear Information System (INIS)

Kustom, R.L.; Fuja, R.E.; Wehrle, R.B.; Smith, R.P.; Kovarik, T.J.

1977-01-01

A single cylinder, drum-type homopolar generator has been designed and built for the purpose of developing a simple air support system for thin cylinder rotors operated at high surface velocities and significant radial drum growth. The model has an aluminum cylinder which is 0.32 cm thick, 25 cm in diameter, and 12.7 cm long. It is designed to operate at a peak current of 2500 A and to store a total of 40 kJ with a surface velocity of 305 m/sec

Contamination control aspects of attaching waste drums to the WIPP Waste Characterization Chamber

International Nuclear Information System (INIS)

Rubick, L.M.; Burke, L.L.

1998-01-01

Argonne National Laboratory West (ANL-W) is verifying the characterization and repackaging of contact-handled transuranic (CH-TRU) mixed waste in support of the Waste Isolation Pilot Program (WIPP) project located in Carlsbad, New Mexico. The WIPP Waste Characterization Chamber (WCC) was designed to allow opening of transuranic waste drums for this process. The WCC became operational in March of 1994 and has characterized approximately 240 drums of transuranic waste. The waste drums are internally contaminated with high levels of transuranic radionuclides. Attaching and detaching drums to the glove box posed serious contamination control problems. Prior to characterizing waste, several drum attachment techniques and materials were evaluated. An inexpensive HEPA filter molded into the bagging material helps with venting during detachment. The current techniques and procedures used to attach and detach transuranic waste drums to the WCC are described

Comparison of the tensile bond strength of high-noble, noble, and base metal alloys bonded to enamel.

Science.gov (United States)

Sen, D; Nayir, E; Pamuk, S

2000-11-01

Although the bond strengths of various resin composite luting materials have been reported in the literature, the evaluation of these systems with various cast alloys of different compositions has not been completely clarified. To evaluate the tensile bond strength of sandblasted high-noble, noble, and base metal alloys bonded to etched enamel by 2 different bonding agents of different chemical composition: Panavia-Ex (BIS-GMA) and Super-Bond (4-META acrylic). Flat enamel surfaces were prepared on buccal surfaces of 60 extracted noncarious human incisors. Teeth were divided into 3 groups of 20 each. Twenty circular disks of 5 mm diameter were prepared for casting for each group. Group I was cast with a high-noble, group II with a noble, and group III with a base metal alloy. The surfaces of the disks were sandblasted with 250 microm Al(2)O(3). Ten disks of each group were bonded to exposed enamel surfaces with Super-Bond and 10 disks with Panavia-Ex as recommended by the manufacturer. The tensile bond strength was measured with an Instron universal testing machine with a crosshead speed of 0.5 mm/min until failure occurred. Two-way ANOVA was used to evaluate the results. The differences in bond strengths of Super-Bond and Panavia-Ex with different alloys were not significant. The highest bond strengths were obtained in base metal alloys, followed by noble and high-noble alloys. These results were significant. Panavia-Ex and Super-Bond exhibited comparable tensile bond strengths. For both luting agents, the highest bond strengths were achieved with base metal alloys and the lowest with high-noble alloys.

Convective heat transfer analysis in aggregates rotary drum reactor

International Nuclear Information System (INIS)

Le Guen, Laurédan; Huchet, Florian; Dumoulin, Jean; Baudru, Yvan; Tamagny, Philippe

2013-01-01

Heat transport characterisation inside rotary drum dryer has a considerable importance linked to many industrial applications. The present paper deals with the heat transfer analysis from experimental apparatus installed in a large-scale rotary drum reactor applied to the asphalt materials production. The equipment including in-situ thermal probes and external visualization by mean of infrared thermography gives rise to the longitudinal evaluation of inner and external temperatures. The assessment of the heat transfer coefficients by an inverse methodology is resolved in order to accomplish a fin analysis of the convective mechanism inside baffled (or flights) rotary drum. The results are discussed and compared with major results of the literature. -- Highlights: ► A thermal and flow experimentation is performed on a large-scale rotary drum. ► Four working points is chosen in the frame of asphalt materials production. ► Evaluation of the convective transfer mechanisms is calculated by inverse method. ► The drying stage is performed in the combustion area. ► Wall/aggregates heat exchanges have a major contribution in the heating stage

Artificial neural networks in the evaluation of the radioactive waste drums activity

International Nuclear Information System (INIS)

Potiens, J.R.A.J.; Hiromoto, G.

2006-01-01

The mathematical techniques are becoming more important to solve geometry and standard identification problems. The gamma spectrometry of radioactive waste drums would be a complex solution problem. The main difficulty is the detectors calibration for this geometry; the waste is not homogeneously distributed inside the drums, therefore there are many possible combinations between the activity and the position of these radionuclides inside the drums, making the preparation of calibration standards impracticable. This work describes the development of a methodology to estimate the activity of a 200 L radioactive waste drum, as well as a mapping of the waste distribution, using Artificial Neural Network. The neural network data set entry obtaining was based on the possible detection efficiency combination with 10 sources activities varying from 0 to 74 x 10 3 Bq. The set up consists of a 200 L drum divided in 5 layers. Ten detectors were positioned all the way through a parallel line to the drum axis, from 15 cm of its surface. The Cesium -137 radionuclide source was used. The 50 efficiency obtained values (10 detectors and 5 layers), combined with the 10 source intensities resulted in a 100,000 lines for 15 columns matrix, with all the possible combinations of source intensity and the Cs-137 position in the 5 layers of the drum. This archive was divided in 2 parts to compose the set of training: input and target files. The MatLab 7.0 module of neural networks was used for training. The net architecture has 10 neurons in the input layer, 18 in the hidden layer and 5 in the output layer. The training algorithm was the 'traincgb' and after 300 'epoch s' the medium square error was 0.00108172. This methodology allows knowing the detection positions answers in a heterogeneous distribution of radionuclides inside a 200 L waste drum; in consequence it is possible to estimate the total activity of the drum in the training neural network limits. The results accuracy depends

Active drumming experience increases infants' sensitivity to audiovisual synchrony during observed drumming actions

NARCIS (Netherlands)

Gerson, S.A.; Schiavio, A.A.R.; Timmers, R.; Hunnius, S.

2015-01-01

In the current study, we examined the role of active experience on sensitivity to multisensory synchrony in six-month-old infants in a musical context. In the first of two experiments, we trained infants to produce a novel multimodal effect (i.e., a drum beat) and assessed the effects of this

Solar thermal drum drying performance of prune and tomato pomaces

Science.gov (United States)

Fruit and vegetable pomaces are co-products of the food processing industry; they are underutilized in part because their high water activity (aw) renders them unstable. Drum drying is one method that can dry/stabilize pomaces, but current drum drying methods utilize conventional, high-environmental...

A method to quantify tritium inside waste drums: He{sup 3} ingrowth method

Energy Technology Data Exchange (ETDEWEB)

Godot, A.; Lepeytre, C.; Hubinois, J.C. [CEA Valduc, Dept. Traitement Materiaux Nucleaires, Service Analyses- Dechets, Lab. Chimie Analytique, 21 - Is-sur-Tille (France); Arseguel, A.; Daclin, J.P.; Douche, C. [CEA Valduc, Dept. Traitement Materiaux Nucleaires, Service Analyses- Dechets, Lab. de Gestion des Dechets Trities, 21 - Is-sur-Tille (France)

2008-07-15

This method enables an indirect, non intrusive and non destructive measurement of the Tritium activity in wastes drums. The amount of tritium enclosed inside a wastes drum can be determined by the measurement of the leak rate of {sup 3}He of this latter. The simulation predicts that a few months are necessary for establishing the equilibrium between the {sup 3}He production inside the drum and the {sup 3}He drum leak. In practice, after one year of storage, sampling {sup 3}He outside the drum can be realized by the mean of a confining chamber that collect the {sup 3}He outflow. The apparatus, the experimental procedure and the calculation of tritium activity from mass spectrometric {sup 3}He measurements are detailed. The industrial device based on a confinement cell and the automated process to measure the {sup 3}He amount at the initial time and after the confinement time is described. Firstly, reference drums containing a certified tritium activity (HTO) in addition to organic materials have been measured to qualify the method and to evaluate its performances. Secondly, tritium activity of organic wastes drums issued from the storage building in Valduc have been determined. Results of the qualification and optimised values of the experimental parameters are reported in order to determine the performances of this industrial device. As a conclusion, the apparatus enables the measurement of an activity as low as 1 GBq of tritium in a 200 liters drum containing organic wastes. (authors)

Design and development of a connection of a magnetic drum with two computers

International Nuclear Information System (INIS)

Malriq, Jean.

1976-01-01

In the experiment in High Energy Physics 'Hyperons SPS' realized at the CERN 300 GeV the connection between a drum and two computers is studied. One of the two computers is a NORD-10 the other may be anyone if it has a CAMAC interface. The input/output structure of the NORD-10 has been studied, then the interface NORD-drum and the CAMAC-drum interface have been realized. The electronic commutation allowing each computer to be connected on the drum through its specific interface has been built [fr

Thermal hydraulic aspects of steam drum level control philosophy for the natural circulation based heavy water reactor

International Nuclear Information System (INIS)

Gupta, S.K.; Gaikwad, A.J.; Kumar, Rajesh

2004-01-01

From safety considerations advanced nuclear reactors rely more and more on passive systems such as natural circulation for primary heat removal. A natural circulation based water reactor is relatively larger in size so as to reduce flow losses and channel type for proper flow distribution. From the size of steam drum considerations it has to be multi loop but has a common inlet header. Normally the turbine follows the reactor. This paper addresses the thermal hydraulic aspects of the steam drum pressure and level control philosophy for a four drum, natural circulation based, channel type boiling water advanced reactor. Three philosophies may be followed for drum control viz. individual drum control, one control drum approach and an average of all the four drums. For drum pressure control, the steam flow to the turbine is be regulated. A single point pressure control is better than individual drum pressure control. This is discussed in the paper. But the control point has to be at a place down steam the point where all steam line from individual drum meet. This may lead to different pressure in all the four drums depending on the power produced in the respective loops. The difference in pressure cannot be removed even if the four drums are directly connected through pipes. Also the pressure control scheme with/without interconnection is discussed. For level, the control of individual drum may not be normally possible because of common inlet header. As the frictional pressure drops in the large diameter downcomers are small as compared to elevation pressure drops, the level in all the steam drum tend to equalize. Consequently a single representative drum level may be chosen as a control variable for controlling level in all the four drums. But in case, where all the four loops are producing different powers and single point pressure control is effective, the scheme may not work satisfactorily. the level in a drum may depend on the power produced in the loop

Small-Scale Experiments.10-gallon drum experiment summary

Energy Technology Data Exchange (ETDEWEB)

Rosenberg, David M.

2015-02-05

A series of sub-scale (10-gallon) drum experiments were conducted to characterize the reactivity, heat generation, and gas generation of mixtures of chemicals believed to be present in the drum (68660) known to have breached in association with the radiation release event at the Waste Isolation Pilot Plant (WIPP) on February 14, 2014, at a scale expected to be large enough to replicate the environment in that drum but small enough to be practical, safe, and cost effective. These tests were not intended to replicate all the properties of drum 68660 or the event that led to its breach, or to validate a particular hypothesis of the release event. They were intended to observe, in a controlled environment and with suitable diagnostics, the behavior of simple mixtures of chemicals in order to determine if they could support reactivity that could result in ignition or if some other ingredient or event would be necessary. There is a significant amount of uncertainty into the exact composition of the barrel; a limited sub-set of known components was identified, reviewed with Technical Assessment Team (TAT) members, and used in these tests. This set of experiments was intended to provide a framework to postulate realistic, data-supported hypotheses for processes that occur in a “68660-like” configuration, not definitively prove what actually occurred in 68660.

A verification calculation of drum and pulley overhead travelling crane on gamma irradiator ISG-500

International Nuclear Information System (INIS)

Syamsurrijal Ramdja; Ari Satmoko; Sutomo Budihardjo

2010-01-01

It has been verified the calculation of drum and pulleys on cranes as facility the gamma irradiator ISG-500. Drum is a device for rolling steel ropes while the pulley is a circular pieces called disks, and both of which are made from metal or non-metal to transmit motion and force. It has been verified the calculation of forces on the drum, drum diameter and length, and pressuring force occurred on the drums. Likewise to the pulley, the pulley diameter calculations verification, size of disc and shaft power pulleys. From the verification results, it will be obtained whether the data drums and pulley device are safe or not safe to be used. (author)

Muonium formation in noble gases and noble gas mixtures

International Nuclear Information System (INIS)

Stambaugh, R.D.; Casperson, D.E.; Crane, T.W.; Hughes, V.W.; Kaspar, H.F.; Souder, P.; Thompson, P.A.; Orth, H.; zu Putlitz, G.; Denison, A.B.

1974-01-01

An experiment is reported to study the behavior of positive muons stopped in He, Ne, and Xe in order to provide a more complete understanding of muonium formation in the noble gases. Free muon and muonium precession are plotted. (U.S.)

A thermal analysis for the use of cooled rotating drums in electron processing

International Nuclear Information System (INIS)

Fletcher, P.M.; Williams, K.E.

1988-01-01

The thermal response of rotating drums under an electron beam has been analyzed using a finite difference thermal analysis computer code. Rotating drums are used to convey thin webs or films under the electron beams while controlling their temperature and, in some cases, in dissipating the exotherm involved in curing coatings applied to them. Each portion of the drum surface receives one heat pulse per rotation as it passes under the beam. The drum's thermal behavior shows both an immediate response to each heat pulse and a more gradual response to the average heat acquired over many pulses. After many rotations a steady state is reached where there is only an immediate response to each heat pulse but the gradual heating has tapered off. Nevertheless the steady state temperatures are strongly dependent on the gradual heating that led to them. Slow and fast speeds of rotation are compared showing the effects of both gradual and immediate heating components. The thermal analysis is extended to include the coolant fluid inside the drum shell and the web on the drum surface. The coolant's incoming temperature, volumetric flow rate, flow speed through the coolant channels and film coefficient between the outer shell and fluid are all included in the analysis. The small air gap between the web and drum, the convective cooling of the web to the ambient air, and the exothermic reaction of any chemical reactions on the web are included. The stresses produced in the drum shell (i.e. between the outer surface and the temperature-controlling fluid within the drum) are analyzed in order to define safe e-beam powers and rotating speeds. The analysis provides the basis for many design decisions and can give an end-user a full temperature history for his product for any set of conditions. (author)

Drum of storing fuel assemblies of nuclear reactor

International Nuclear Information System (INIS)

Artemiev, L.N.; Batjukov, V.I.; Fadeev, A.I.

1979-01-01

The proposed drum for storing fuel assemblies of a nuclear reactor comprises a holder rotatable around its axis and provided with tubular sockets arranged in concentric rows along the circumference of the holder so that the axis of at least one socket of each row intersects the trajectory described by the grip of the recharging mechanism in the course of its movement. The proposed drum design makes it possible to facilitate and speed up the process of recharging fuel asemblies

49 CFR 178.506 - Standards for metal drums other than steel or aluminum.

Science.gov (United States)

2010-10-01

... aluminum. 178.506 Section 178.506 Transportation Other Regulations Relating to Transportation PIPELINE AND... drums other than steel or aluminum. (a) The following are the identification codes for metal drums other than steel or aluminum: (1) 1N1 for a non-removable head metal drum; and (2) 1N2 for a removable head...

A model of gas generation and transport within TRU [transuranic] waste drums

International Nuclear Information System (INIS)

Smith, F.G. III.

1987-01-01

Gas generation from the radiolytic decomposition of organic material contaminated with plutonium is modeled. Concentrations of gas throughout the waste drum are determined using a diffusional transport model. The model accurately reproduces experimentally measured gas concentrations. With polyethylene waste in unvented drums, the model predicts that hydrogen gas can accumulate to concentrations greater than 4 mole percent (lower flammable limit) with about 5 Ci of plutonium. Polyethylene provides a worst case for combustible waste material. If the drum liner is punctured and a carbon composite filter vent is installed in the drum lid, the plutonium loading can be increased to 240 Ci without generating flammable gas mixtures. 5 refs., 7 figs., 4 tabs

Measuring the noble metal and iodine composition of extracted noble metal phase from spent nuclear fuel using instrumental neutron activation analysis

International Nuclear Information System (INIS)

Palomares, R.I.; Dayman, K.J.; Landsberger, S.; Biegalski, S.R.; Soderquist, C.Z.; Casella, A.J.; Brady Raap, M.C.; Schwantes, J.M.

2015-01-01

Masses of noble metal and iodine nuclides in the metallic noble metal phase extracted from spent fuel are measured using instrumental neutron activation analysis. Nuclide presence is predicted using fission yield analysis, and radionuclides are identified and the masses quantified using neutron activation analysis. The nuclide compositions of noble metal phase derived from two dissolution methods, UO 2 fuel dissolved in nitric acid and UO 2 fuel dissolved in ammonium-carbonate and hydrogen-peroxide solution, are compared. - Highlights: • The noble metal phase was chemically extracted from spent nuclear fuel and analyzed non-destructively. • Noble metal phase nuclides and long-lived iodine were identified and quantified using neutron activation analysis. • Activation to shorter-lived radionuclides allowed rapid analysis of long-lived fission products in spent fuel using gamma spectrometry

Device to measure level in a steam drum of NPP

International Nuclear Information System (INIS)

Vinogradov, Yu.A.

1988-01-01

Gravitation-hydrostatic device for measuring coolant level in a steam drum of NPP is described. The device enables to improve the accuracy and sensitivity of measuring coolant level above and below the submerged perforated sheet of the steam drum and decrease the amount of levelling vessels in the unit by 50%. 1 fig

Characterization of void volume VOC concentration in vented TRU waste drums - an interim report

International Nuclear Information System (INIS)

Liekhus, K.J.

1994-09-01

A test program is underway at the Idaho National Engineering Laboratory to determine if the concentration of volatile organic compounds (VOCs) in the drum headspace is representative of the VOC concentration in the entire drum void space and to demonstrate that the VOC concentration in the void space of each layer of confinement can be estimated using a model incorporating diffusion and permeation transport principles and limited waste drum sampling data. An experimental test plan was developed requiring gas sampling of 66 transuranic (TRU) waste drums. This interim report summarizes the experimental measurements and model predictions of VOC concentration in the innermost layer of confinement from waste drums sampled and analyzed in FY 1994

The method study for nuclide analysis of waste drum

International Nuclear Information System (INIS)

Ruan Guanglin; Huang Xianguo; Xing Shixiong

2001-01-01

The principle of waste drum nuclide analysis system and the principle of the detector chosen are introduced. The linear attenuation coefficient and mass attenuation coefficient of five environmental medium (water, soil, red brick, concrete and sands) have been measured with γ transmission method simulative equipment. The absorption coefficient and nuclide activity of three measuring conditions (collimation-columnar source, un-collimation-columnar source, and un-collimation-rotation-drum source) have been calculated

Possibilities of rotating drums in ultra-high-speed cinematography

International Nuclear Information System (INIS)

Andre, Michel

A theoretical study shows that it is possible to produce a drum rotating at a peripheral speed of 500m/s. A prototype has actually reached this speed and confirmed the feasibility of the system. It is driven by an electric motor and is made of titanium covered with boron fibres. The main performances to be expected of cameras (whole-image, slit or spectrographic) using such a drum is described [fr

ANALYSIS OF DESIGN PECULIARITIES PERTAINING TO DRUMS OF CONTINUOUS MACHINES

Directory of Open Access Journals (Sweden)

V. Yu. Prushak

2007-01-01

Full Text Available The paper considers design peculiarities of belt conveyor drums in respect of their operational reliability; their advantages and disadvantages have been analyzed. There are some proposals presenting technical solutions to modernization of belt conveyor drum designs which presuppose reduction of their material consumption while preserving their strength and general rigidity. 

Analytical and experimental evaluation of solid waste drum fire performance volumes I and II

Energy Technology Data Exchange (ETDEWEB)

Hecker, C.F., [Los Alamos Technical Associates, Inc., Kennewick, WA (United States); Rhodes, B.T.; Beitel, J.J.; Gottuk, D.T.; Beyler, C.L.; Rosenbaum, E.R., [Hughes Associates, Inc., Columbia, MD (United States)

1995-04-28

Fire hazards associated with drum storage of radioactively contaminated wastes are a major concern in DOE facilities design for long term storage of solid wastes in drums. These facilities include drums stored in pallet arrays and in rack storage systems. This report details testing in this area

Techniques for improving shuffler assay results for 55-gallon waste drums

International Nuclear Information System (INIS)

Rinard, P.M.; Prettyman, T.H.; Stuenkel, D.

1994-01-01

Accurate assays of the fissile contents in waste drums are needed to ensure the most proper and economical handling and disposal of the waste. An improvement of accuracy will mean fewer drums disposed as transuranic waste when they really contain low-level waste, saving both money and burial sites. Shufflers are used for assaying waste drums and are very accurate with nonmoderating matrices (such as iron). In the active mode they count delayed neutrons released after fissions are induced by irradiation neutrons from a 252 Cf source. However, as the hydrogen density from matrices such as paper or gloves increases, the accuracy can suffer without proper attention. The neutron transport and fission probabilities change with the hydrogen density, causing the neutron count rate to vary with the position of the fissile material within the drum. The magnitude of this variation grows with the hydrogen density

EARLY TESTS OF DRUM TYPE PACKAGINGS - THE LEWALLEN REPORT

Energy Technology Data Exchange (ETDEWEB)

Smith, A.

2010-07-29

The need for robust packagings for radioactive materials (RAM) was recognized from the earliest days of the nuclear industry. The U.S. Department of Energy (DOE) Rocky Flats Plant developed a packaging for shipment of Pu in the early 1960's, which became the U.S. Department of Transportation (DOT) 6M specification package. The design concepts were employed in other early packagings. Extensive tests of these at Savannah River Laboratory (now Savannah River National Laboratory) were performed in 1969 and 1970. The results of these tests were reported in 'Drum and Board-Type Insulation Overpacks of Shipping Packages for Radioactive Materials', by E. E. Lewallen. The Lewallen Report was foundational to design of subsequent drum type RAM packaging. This paper summarizes this important early study of drum type packagings. The Lewallen Report demonstrated the ability packagings employing drum and insulation board overpacks and engineered containment vessels to meet the Type B package requirements. Because of the results of the Lewallen Report, package designers showed high concern for thermal protection of 'Celotex'. Subsequent packages addressed this by following strategies like those recommended by Lewallen and by internal metal shields and supplemental, encapsulated insulation disks, as in 9975. The guidance provide by the Lewallen Report was employed in design of a large number of drum size packagings over the following three decades. With the increased public concern over transportation of radioactive materials and recognition of the need for larger margins of safety, more sophisticated and complex packages have been developed and have replaced the simple packagings developed under the Lewallen Report paradigm.

Reconstruction of the isotope activity content of heterogeneous nuclear waste drums.

Science.gov (United States)

Krings, Thomas; Mauerhofer, Eric

2012-07-01

Radioactive waste must be characterized in order to verify its conformance with national regulations for intermediate storage or its disposal. Segmented gamma scanning (SGS) is a most widely applied non-destructive analytical technique for the characterization of radioactive waste drums. The isotope specific activity content is generally calculated assuming a homogeneous matrix and activity distribution for each measured drum segment. However, real radioactive waste drums exhibit non-uniform isotope and density distributions most affecting the reliability and accuracy of activities reconstruction in SGS. The presence of internal shielding structures in the waste drum contributes generally to a strong underestimation of the activity and this in particular for radioactive sources emitting low energy gamma-rays independently of their spatial distribution. In this work we present an improved method to quantify the activity of spatially concentrated gamma-emitting isotopes (point sources or hot spots) in heterogeneous waste drums with internal shielding structures. The isotope activity is reconstructed by numerical simulations and fits of the angular dependent count rate distribution recorded during the drum rotation in SGS using an analytical expression derived from a geometric model. First results of the improved method and enhancements of this method are shown and are compared to each other as well as to the conventional method which assumes a homogeneous matrix and activity distribution. It is shown that the new model improves the accuracy and the reliability of the activity reconstruction in SGS and that the presented algorithm is suitable with respect to the framework requirement of industrial application. Copyright © 2011 Elsevier Ltd. All rights reserved.

Study on the dynamic performance of concrete mixer's mixing drum

Directory of Open Access Journals (Sweden)

J. Yang

2017-06-01

Full Text Available When working, the geometric distribution shape of concrete in concrete mixing truck's rotary drum changes continuously, which cause a great difficulty for studying the dynamic performance of the mixing drum. In this paper, the mixing system of a certain type of concrete mixing truck is studied. A mathematical formulation has been derived through the force analysis to calculate the supporting force. The calculation method of the concrete distribution shape in the rotary drum is developed. A new transfer matrix is built with considering the concrete geometric distribution shape. The effects of rotating speed, inclination angle and concrete liquid level on the vibration performance of the mixing drum are studied with a specific example. Results show that with the increase of rotating speed, the vibration amplitude of the mixing drum decreases. The peak amplitude gradually moves to the right with the inclination angle increasing. The amplitude value of the peak's left side decreases when tilt angle increases, while the right side increases. The maximum unbalanced response amplitude of the drum increases with the decrease of concrete liquid level height, and the vibration peak moves to the left.

Renewable Energy Opportunities at Fort Drum, New York

Energy Technology Data Exchange (ETDEWEB)

Brown, Scott A.; Orrell, Alice C.; Solana, Amy E.; Williamson, Jennifer L.; Hand, James R.; Russo, Bryan J.; Weimar, Mark R.; Rowley, Steven; Nesse, Ronald J.

2010-10-20

This document provides an overview of renewable resource potential at Fort Drum, based primarily upon analysis of secondary data sources supplemented with limited on-site evaluations. This effort focuses on grid-connected generation of electricity from renewable energy sources and also on ground source heat pumps for heating and cooling buildings. The effort was funded by the U.S. Army Installation Management Command (IMCOM) as follow-on to the 2005 Department of Defense (DoD) Renewables Assessment. The site visit to Fort Drum took place on May 4 and 5, 2010.

Qualitative and quantitative analysis of plutonium in solid waste drums

International Nuclear Information System (INIS)

Anno, Jacques; Escarieux, Emile

1977-01-01

An assessment of the results given by a study carried out for the development of qualitative and quantitative analysis, by γ spectrometry, of plutonium in solid waste drums is presented. After having reminded the standards and their incidence on the quantities of plutonium to be measured (application at industrial Pu: 20% of Pu 240 ) the equipment used is described. Measurement station provided with a mechanical system consisting of: a rail and a pulley block to bring the drums; a pit and a hydraulic jack with a rotating platform. The detection instrumentation consisting of: a high volume coaxial Ge(Li) detector with a γ ray resolution of 2 keV; an associated electronic; a processing of data by a 'Plurimat 20' minicomputer. Principles of the identification and measurements are specified and supported by experimental results. They are the following: determination of the quality of Pu by measuring the ratio between the γ ray intensities of the 239 Pu 129 keV and of the 241 Pu 148 keV; measurement of the 239 Pu mass by estimating the γ ray counting rate of the 375 keV from the calibrating curves given by plutonium samples varying from 32 mg to 80 g; correction of the results versus the source position into the drum and versus the filling in plastic materials into this drum. The experimental results obtained over 40 solid waste drums are presented along with the error estimates [fr

Considerations for an active and passive scanner to assay nuclear waste drums

International Nuclear Information System (INIS)

Martz, H.E.; Azevedo, S.G.; Roberson, G.P.; Schneberk, D.J.; Koenig, Z.M.; Camp, D.C.

1990-01-01

Radioactive wastes are generated at many DOE laboratories, military facilities, fuel fabrication and enrichment plants, reactors, hospitals, and university research facilities. At all of these sites, wastes must be separated, packaged, categorized, and packed into some sort of container--usually 208-L (55-gal) drums--for shipment to waste-storage sites. Prior to shipment, the containers must be labeled, assayed, and certified; the assay value determines the ultimate disposition of the waste containers. An accurate nondestructive assay (NDA) method would identify all the radioisotopes present and provide a quantitative measurement of their activity in the drum. In this way, waste containers could be routed in the most cost-effective manner and without having to reopen them. Currently, the most common gamma-ray method used to assay nuclear waste drums is segmented gamma-ray scanning (SGS) spectrometer that crudely measures only the amount of 235 U or 239 Pu present in the drum. This method uses a spatially-averaged, integrated, emitted gamma-ray-intensity value. The emitted intensity value is corrected by an assumed constant-attenuation value determined by a spatially-averaged, transmission (or active) measurement. Unfortunately, this typically results in an inaccurate determination of the radioactive activities within a waste drum because this measurement technique is valid only for homogeneous-attenuation or known drum matrices. However, since homogeneous-attenuation matrices are not common and may be unknown, other NDA techniques based on active and Passive CT (A ampersand PCT) are under development. The active measurement (ACT) yields a better attenuation matrix for the drum, while the passive measurement (PCT) more accurately determines the identity of the radioisotopes present and their activities. 9 refs., 2 figs

Research Based on the Acoustic Emission of Wind Power Tower Drum Dynamic Monitoring Technology

Science.gov (United States)

Zhang, Penglin; Sang, Yuan; Xu, Yaxing; Zhao, Zhiqiang

Wind power tower drum is one of the key components of the wind power equipment. Whether the wind tower drum performs safety directly affects the efficiency, life, and performance of wind power equipment. Wind power tower drum in the process of manufacture, installation, and operation may lead to injury, and the wind load and gravity load and long-term factors such as poor working environment under the action of crack initiation or distortion, which eventually result in the instability or crack of the wind power tower drum and cause huge economic losses. Thus detecting the wind power tower drum crack damage and instability is especially important. In this chapter, acoustic emission is used to monitor the whole process of wind power tower drum material Q345E steel tensile test at first, and processing and analysis tensile failure signal of the material. And then based on the acoustic emission testing technology to the dynamic monitoring of wind power tower drum, the overall detection and evaluation of the existence of active defects in the whole structure, and the acoustic emission signals collected for processing and analysis, we could preliminarily master the wind tower drum mechanism of acoustic emission source. The acoustic emission is a kind of online, efficient, and economic method, which has very broad prospects for work. The editorial committee of nondestructive testing qualification and certification of personnel teaching material of science and technology industry of national defense, "Acoustic emission testing" (China Machine Press, 2005.1).

US Department of Transportation (DOT) Spec 7A Type A evaluation document: Spec 17C 55-gal steel drum with RWMC/SWEPP drum venting system carbon filter assembly

International Nuclear Information System (INIS)

Edling, D.A.

1986-01-01

As part of MRC-Mound's responsibility to coordinate DOE Spec 7A Type A Packaging testing, evaluation, and utilization, this document evaluates per 49CFR 173.415(a) the SWEPP packaging system: DOT Spec 17C steel drums - 30, 55 and 83-gal; High Density Polyethylene (HDPE) liners; and SWEPP DVS Filter Assemblies (two configurations) as a US DOT Spec 7A Type A packaging. A variety of Type A performance testing was done on: DOT Spec 17C 55-gal steel drums; DOT Spec 17C 55-gal steel drums with HDPE liners; and DOT Spec 17C 55-gal steel drums with ''Nucfil'' filters as part of MRC-Mound's Type A Packaging Evaluation Program funded by DOE/HQ, DP-4, Security Evaluations. The subject SWEPP packaging incorporates modifications to the ''Nucfil'' filter and installation assembly previously tested in conjunction with the Spec 17C 55-gal drums. Thus, additional testing was required on the new filter installation in order to evaluate the entire packaging system. This document presents the test data to demonstrate the SWEPP packaging system's performance against the DOT 7A Type A requirements

Electromechanical dynamic analysis for the drum driving system of the long-wall shearer

Directory of Open Access Journals (Sweden)

Changzhao Liu

2015-10-01

Full Text Available The drum driving system is one of the weakest parts of the long-wall shearer, and some methods are also needed to monitor and control the long-wall shearer to adapt to the important trend of unmanned operation in future mining systems. Therefore, it is essential to conduct an electromechanical dynamic analysis for the drum driving system of the long-wall shearer. First, a torsional dynamic model of planetary gears is proposed which is convenient to be connected to the electric motor model for electromechanical dynamic analysis. Next, an electromechanical dynamic model for the drum driving system is constructed including the electric motor, the gear transmission system, and the drum. Then, the electromechanical dynamic characteristics are simulated when the shock loads are acted on the drum driving system. Finally, some advices are proposed for improving the reliability, monitoring the operating state, and choosing the control signals of the long-wall shearer based on the simulation.

Characterization of voic volume VOC concentration in vented TRU waste drums. Final report

Energy Technology Data Exchange (ETDEWEB)

Liekhus, K.J.

1994-12-01

A test program has been conducted at the Idaho National Engineering Laboratory to demonstrate that the concentration of volatile organic compounds within the innermost layer of confinement in a vented waste drum can be estimated using a model incorporating diffusion and permeation transport principles and limited waste drum sampling data. This final report summarizes the experimental measurements and model predictions for transuranic waste drums containing solidified sludges and solid waste.

Comprehensive investigation of the metal in drums of boilers at thermal power stations

Science.gov (United States)

Ozhigov, L. S.; Mitrofanov, A. S.; Tolstolutskaya, G. D.; Vasilenko, R. L.; Rudenko, A. G.; Ruzhytskyi, V. V.; Ribalchenko, N. D.; Shramchenko, S. V.

2017-05-01

A comparative investigation of the metal of drums of two TP-100 boilers at the Starobeshevskaya and the Lugansk thermal power stations (TPS) was performed. Their operation time was approximately 300000 hours; the shell of one drum was ruptured during a hydraulic test, and the other drum is in operation. According to the results of the technical diagnostics and a strength analysis, both drums comply with the applicable regulatory requirements. The objects of the investigation were fragments of the ruptured drum and a "plug" cut out of the shell during a scheduled inspection. The investigation was carried out by microscopic metallography methods and the scanning electron microscopy technique. Mechanical tests of metal specimens were performed, and the hydrogen content in these specimens was measured. Prior to the material research, the metal was examined using a magnetic memory method. The investigation yielded specifics of the metal microstructure, mechanical properties, and fracture patterns of the metal specimens at various temperatures. An investigation performed by the method of thermal-desorption mass spectrometry revealed no considerable difference in the hydrogen content in the metal of both drums, thereby excluding the effect of hydrogenation in analyzing the rupture causes. It was established that the drum at the Starobeshevskaya TPS had been damaged due to its low impact strength at room temperature and high brittle-ductile transition point. Comparison of the metallographic study data with the results obtained using the magnetic memory method suggests that the fracture was caused by local formation of the Widmannstatten pattern at points where accessories are welded to the shell. The prospects are demonstrated of the comprehensive approach to nondestructive examination (NDE) of TPS drums using the magnetic memory technique and metallographic methods.

Investigations with respect to pressure build-up in 200 l drums with supercompacted low level waste (LLW)

International Nuclear Information System (INIS)

Kroth, K.; Lammertz, H.

1988-04-01

In the drum storage facilities of various nuclear power stations, ballooning effects have recently been observed on a limited number of 200 l drums filled with hypercompacted mixed LLW. The ballooning of the drums lid and bottom is due to internal overpressure caused by gas formation in the waste. The internal drum pressures and the composition of the drum gases were measured on a considerable number of 200 l drums. Hydrogen, formed by chemical reactions between the waste components, was identified as the pressure generating gas. The reasons for the hydrogen formation were investigated on both real and simulated wastes. (orig.) [de

Monte Carlo method to characterize radioactive waste drums

International Nuclear Information System (INIS)

Lima, Josenilson B.; Dellamano, Jose C.; Potiens Junior, Ademar J.

2013-01-01

Non-destructive methods for radioactive waste drums characterization have being developed in the Waste Management Department (GRR) at Nuclear and Energy Research Institute IPEN. This study was conducted as part of the radioactive wastes characterization program in order to meet specifications and acceptance criteria for final disposal imposed by regulatory control by gamma spectrometry. One of the main difficulties in the detectors calibration process is to obtain the counting efficiencies that can be solved by the use of mathematical techniques. The aim of this work was to develop a methodology to characterize drums using gamma spectrometry and Monte Carlo method. Monte Carlo is a widely used mathematical technique, which simulates the radiation transport in the medium, thus obtaining the efficiencies calibration of the detector. The equipment used in this work is a heavily shielded Hyperpure Germanium (HPGe) detector coupled with an electronic setup composed of high voltage source, amplifier and multiport multichannel analyzer and MCNP software for Monte Carlo simulation. The developing of this methodology will allow the characterization of solid radioactive wastes packed in drums and stored at GRR. (author)

Noble Gas signatures of Enhanced Oil Recovery

Science.gov (United States)

Barry, P. H.; Kulongoski, J. T.; Tyne, R. L.; Hillegonds, D.; Byrne, D. J.; Landon, M. K.; Ballentine, C. J.

2017-12-01

Noble gases are powerful tracers of fluids from various oil and gas production activities in hydrocarbon reservoirs and nearby groundwater. Non-radiogenic noble gases are introduced into undisturbed oil and natural gas reservoirs through exchange with formation waters [1-3]. Reservoirs with extensive hydraulic fracturing, injection for enhanced oil recovery (EOR), and/or waste disposal also show evidence for a component of noble gases introduced from air [4]. Isotopic and elemental ratios of noble gases can be used to 1) assess the migration history of the injected and formation fluids, and 2) determine the extent of exchange between multiphase fluids in different reservoirs. We present noble gas isotope and abundance data from casing, separator and injectate gases of the Lost Hills and Fruitvale oil fields in the San Joaquin basin, California. Samples were collected as part of the California State Water Resource Control Board's Oil and Gas Regional Groundwater Monitoring Program. Lost Hills (n=7) and Fruitvale (n=2) gases are geochemically distinct and duplicate samples are highly reproducible. Lost Hills casing gas samples were collected from areas where EOR and hydraulic fracturing has occurred in the past several years, and from areas where EOR is absent. The Fruitvale samples were collected from a re-injection port. All samples are radiogenic in their He isotopes, typical of a crustal environment, and show enrichments in heavy noble gases, resulting from preferential adsorption on sediments. Fruitvale samples reflect air-like surface conditions, with higher air-derived noble gas concentrations. Lost Hills gases show a gradation from pristine crustal signatures - indicative of closed-system exchange with formation fluids - to strongly air-contaminated signatures in the EOR region. Pristine samples can be used to determine the extent of hydrocarbon exchange with fluids, whereas samples with excess air can be used to quantify the extent of EOR. Determining noble

Predation of the zebra mussel (Dreissena polymorpha) by freshwater drum in western Lake Erie

Science.gov (United States)

French, John R. P.; Bur, Michael T.; Nalepa, Thomas F.; Schloesser, Donald W.

1992-01-01

Environmental and economic problems associated with the colonization of zebra mussels (Dreissena polymorpha) in western Lake Erie created a need to investigate control mechanisms. Predation by fishes is one potential means of control, but predation on zebra mussels by native fishes in Lake Erie is unknown. The freshwater drum (Aplodinotus grunniens) is the most likely fish predator since it is the only fish with pharyngeal teeth capable of crushing mollusk shells. In 1990, freshwater drum were collected in western Lake Erie from 9 sites near rocky reefs and 13 sites with silt or sand bottoms, and gut contents were examined. Predation on zebra mussels increased as drum size increased. Small drum (200-249 mm in length) fed mainly on dipterans, amphipods, and small fish; small zebra mussels (375 mm in length) fed almost exclusively on zebra mussels (seasons and locations combined). The smallest drum capable of crushing zebra mussel shells was 265 mm. Since freshwater drum over 375 mm feed heavily on zebra mussels, they may become a possible biological control mechanism for mussels in portions of North America.

The design, construction, and operation of the Integrated Radwaste Treatment System (IRTS) Drum Cell

International Nuclear Information System (INIS)

Landau, B.; Russillo, A.; Frank, D.; Garland, D.

1989-12-01

This report describes the design, construction, and the operation of the Integrated Radwaste Treatment Systems (IRTS) Drum Cell at the West Valley Demonstration Project (WVDP), West Valley, New York. The IRTS Drum Cell was designed to provide a shielded, secure storage area for the remote handling and placement of low-level Class C radioactive waste produced in the IRTS. The Drum Cell was designed to contain up to approximately 8,804 drums from decontaminated supernatant processing. This waste is to be poured into 0.27m 3 in a temperature controlled environment to ensure the cement will not be subjected to freezing and thawing cycles. A Temporary Weather Structure (TWS), a pre-engineered building, now encloses the Drum Cell and associated equipment so that remote waste-handling and placement operations can continue without regard to weather conditions. The Drum Cell was designed so that this TWS could be removed and the low-level waste entombed in place. Final disposition of this low-level waste is currently being evaluated in an Environmental Impact Statement (EIS). 10 refs., 11 figs., 1 tab

Burning test on a storage drum filled with a mixture of sodiumnitrate and bitumen

International Nuclear Information System (INIS)

Knotik, K.; Leichter, P.; Spalek, K.

1979-01-01

A burning test on a common storage drum filled with a mixture of sodiumnitrate and bitumen was carried out to show the incinerability of said mixture. A 50 l mild steel drum was filled with 80,7 kg sodiumnitrate/bitumen-mixture. The drum was packed in a 200 l mild steel drum, the remaining space was filled with enough sand to cover the top of the inner drum with 15 cm of sand. The sand packing was then soaked with 70 l of light distillate fuel and ignited. The fuel burned until self-extinguishing occurred. 30 % (22,2 l) of the fuel was burned. 0,7 % of the energy potential was absorbed in the sand layer. The highest measured temperature was 34 0 C at the top of the test drum. It can be concluded, that even under severe external actions the ignition temperature of 400 0 C for bitumen/waste mixtures cannot be reached, providing correct technical storage conditions, which means that the void space in the cavities is filled with unburnable absorbing material like sand or salt. (author)

Noble magnetic barriers in the ASDEX UG tokamak

Science.gov (United States)

Ali, Halima; Punjabi, Alkesh; Vazquez, Justin

2010-02-01

The second-order perturbation method of creating invariant tori inside chaos in Hamiltonian systems (Ali, H.; Punjabi, A. Plasma Phys. Contr. F. 2007, 49, 1565-1582) is applied to the axially symmetric divertor experiment upgrade (ASDEX UG) tokamak to build noble irrational magnetic barriers inside chaos created by resonant magnetic perturbations (m, n)=(3, 2)+(4, 3), with m and n the poloidal and toroidal mode numbers of the Fourier expansion of the magnetic perturbation. The radial dependence of the Fourier modes is ignored. The modes are considered to be locked and have the same amplitude δ. A symplectic mathematical mapping in magnetic coordinates is used to integrate magnetic field line trajectories in the ASDEX UG. Tori with noble irrational rotational transform are the last ones to be destroyed by perturbation in Hamiltonian systems. For this reason, noble irrational magnetic barriers are built inside chaos, and the strongest noble irrational barrier is identified. Three candidate locations for the strongest noble barrier in ASDEX UG are selected. All three candidate locations are chosen to be roughly midway between the resonant rational surfaces ψ32 and ψ43. ψ is the magnetic coordinate of the flux surface. The three candidate surfaces are the noble irrational surfaces close to the surface with q value that is a mediant of q=3/2 and 4/3, q value of the physical midpoint of the two resonant surfaces, and the q value of the surface where the islands of the two perturbing modes just overlap. These q values of the candidate surfaces are denoted by q MED, q MID, and q OVERLAP. The strongest noble barrier close to q MED has the continued fraction representation (CFR) [1;2,2,1∞] and exists for δ≤2.6599×10-4; the strongest noble barrier close to q MID has CFR [1;2,2,2,1∞] and exists for δ≤4.6311×10-4; and the strongest noble barrier close to q OVERLAP has CFR [1;2,2,6,2,1∞] and exists for δ≤1.367770×10-4. From these results, the strongest

The Welding Effect on Mechanical Strength of Low Level Radioactive Waste Drum Container

International Nuclear Information System (INIS)

Aisyah; Herlan Martono

2007-01-01

The treatment of compactable low level solid waste was started by compaction of 100 liter drum containing the waste using 600 kN hydraulic press in 200 liters drum. The 200 liter drum of waste container containing of compacted waste then immobilized with cement and stored in interm storage. The 200 liter drum of waste container made of carbon steel material to comply with a good mechanical strength request in order to be able to retain the waste content for long period. Welding is a one step in a waste drum container fabrication process that has an opportunity in decreasing these mechanical strength. The research is carried out by welding the waste drum container material sample by electric arc welding. Mechanical strength test carried out by measuring the tensile strength by using the tensile strength machine, hardness test by using Vickers hardness test and microstructure observation by using the optic microscope. The result shows that the welding cause the microstructure changes, its meaning of forming ferro oxide phase on welding area that leads to the brittle material, so that the mechanical strength has a decreasing slightly. Nevertheless the decreasing of mechanical strength is still in the range of safety limit. (author)

The media, the reconstruction of drumming, and the tradition of the ...

African Journals Online (AJOL)

The Prodigal Ones by Mount Zion Films Production (and other drum music performance in films) shows the media enhancement of the performance of the ensemble serving as accompaniment during a traditional festival. The short scene allocated to a traditional festival reveals the significance of drumming and the input of ...

Identification of the fast and thermal neutron characteristics of transuranic waste drums

Energy Technology Data Exchange (ETDEWEB)

Storm, B.H. Jr.; Bramblett, R.L. [Lockheed Martin Specialty Components, Largo, FL (United States); Hensley, C. [Oak Ridge National Lab., TN (United States)

1997-11-01

Fissile and spontaneously fissioning material in transuranic waste drums can be most sensitively assayed using an active and passive neutron assay system such as the Active Passive Neutron Examination and Assay. Both the active and the passive assays are distorted by the presence of the waste matrix and containerization. For accurate assaying, this distortion must be characterized and accounted for. An External Matrix Probe technique has been developed that accomplishes this task. Correlations between in-drum neutron flux measurements and monitors in the Active Passive Neutron Examination and Assay chamber with various matrix materials provide a non-invasive means of predicting the thermal neutron flux in waste drums. Similarly, measures of the transmission of fast neutrons emitted from sources in the drum. Results obtained using the Lockheed Martin Specialty Components Active Passive Neutron Examination and Assay system are discussed. 12 figs., 1 tab.

The Extraordinary Nature of Barney's Drumming : A Complementary Study of Ordinary Noise Making in Chimpanzees

NARCIS (Netherlands)

Dufour, Valérie; Pasquaretta, Cristian; Gayet, Pierre; Sterck, Elisabeth H M

In a previous study (Dufour et al., 2015) we reported the unusual characteristics of the drumming performance of a chimpanzee named Barney. His sound production, several sequences of repeated drumming on an up-turned plastic barrel, shared features typical for human musical drumming: it was

Noble-Metal Chalcogenide Nanotubes

Directory of Open Access Journals (Sweden)

Nourdine Zibouche

2014-10-01

Full Text Available We explore the stability and the electronic properties of hypothetical noble-metal chalcogenide nanotubes PtS2, PtSe2, PdS2 and PdSe2 by means of density functional theory calculations. Our findings show that the strain energy decreases inverse quadratically with the tube diameter, as is typical for other nanotubes. Moreover, the strain energy is independent of the tube chirality and converges towards the same value for large diameters. The band-structure calculations show that all noble-metal chalcogenide nanotubes are indirect band gap semiconductors. The corresponding band gaps increase with the nanotube diameter rapidly approaching the respective pristine 2D monolayer limit.

77 FR 70159 - Marble River, LLC v. Noble Clinton Windpark I, LLC, Noble Ellenburg Windpark, LLC, Noble...

Science.gov (United States)

2012-11-23

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. EL13-20-000] Marble River... Commission's (Commission) Rules of Practice and Procedure, Marble River, LLC (Marble River or Complainant.... (NYISO or Respondent), alleging that Noble failed to pay Marble River for headroom created by common...

Coke drums inspection and evaluation using stress and strain analysis techniques

Energy Technology Data Exchange (ETDEWEB)

Haraguchi, Marcio Issamu [Tricom Tecnologia e Servicos de Manutencao Industrial Ltda., Piquete, SP (Brazil); Samman, Mahmod [Houston Engineering Solutions, Houston, TX (United States); Tinoco, Ediberto Bastos; Marangone, Fabio de Castro; Silva, Hezio Rosa da; Barcelos, Gustavo de Carvalho [Petroleo Brasileiro S.A. (PETROBRAS), Rio de Janeiro, RJ (Brazil)

2012-07-01

Coke drums deform due to a complex combination of mechanical and thermal cyclic stresses. Bulges have progressive behavior and represent the main maintenance problem related to these drums. Bulge failure typically result in through-wall cracks, leaks, and sometimes fires. Such failures generally do not represent a great risk to personnel. Repairs needed to maintain reliability of these vessels might require extensive interruption to operation which in turn considerably impacts the profitability of the unit. Therefore the condition, progression and severity of these bulges should be closely monitored. Coke drums can be inspected during turnaround with 3D Laser Scanning and Remote Visual Inspection (RVI) tools, resulting in a detailed dimensional and visual evaluation of the internal surface. A typical project has some goals: inspect the equipment to generate maintenance or inspection recommendations, comparison with previous results and baseline data. Until recently, coke drum structural analysis has been traditionally performed analyzing Stress Concentration Factors (SCF) thought Finite Element Analysis methods; however this technique has some serious technical and practical limitations. To avoid these shortcomings, the new strain analysis technique PSI (Plastic Strain Index) was developed. This method which is based on API 579/ ASME FFS standard failure limit represents the state of the art of coke drum bulging severity assessment has an excellent correlation with failure history. (author)

Analytical and empirical evaluation of low-level waste drum response to accident environments

International Nuclear Information System (INIS)

May, R.A.; Romesberg, L.E.; Yoshimura, H.R.; Baker, W.E.; Hokanson, J.C.

1980-01-01

Based on results of tests to date, it was found that the structural response of low-level waste drums to impact environments can be generally predicted, both analytically and with subscale models. As currently represented, only the 1/4 scale models would adequately represent full scale drum deformation; however, additional work has shown that with proper heat treating the strength of the material used in the 1/8 scale containers can be reduced to the correct value. Both analytical models give results that are expected to be within the range of behavior of the full scale drums. Failure of the drum closure can be adequately inferred from the radial deformation results of both subscale tests and computer analyses. 6 figures

Structural energetics of noble metals

International Nuclear Information System (INIS)

Mujibur Rahman, S.M.

1982-06-01

Structural energetics of the noble metals, namely Cu, Ag, and Au are investigated by employing a single-parameter pseudopotential. The calculations show that the lowest energy for all of these metals corresponds to FCC - their observed crystal structure. The one-electron contribution to the free energy is found to dominate the structural prediction for these metals. The present investigation strongly emphasizes that the effects due to band hybridization and core-core exchange play a significant role on the structural stability of the noble metals. (author)

Alternatives to reduce corrosion of carbon steel storage drums

International Nuclear Information System (INIS)

Zirker, L.R.; Beitel, G.A.

1995-11-01

The major tasks of this research were (a) pollution prevention opportunity assessments on the overpacking operations for failed or corroded drums, (b) research on existing container corrosion data, (c) investigation of the storage environment of the new Resource Conservation and Recovery Act Type II storage modules, (d) identification of waste streams that demonstrate deleterious corrosion affects on drum storage life, and (e) corrosion test cell program development. Twenty-one waste streams from five US Department of Energy (DOE) sites within the DOE Complex were identified to demonstrate a deleterious effect to steel storage drums. The major components of these waste streams include acids, salts, and solvent liquids, sludges, and still bottoms. The solvent-based waste streams typically had the shortest time to failure: 0.5 to 2 years. The results of this research support the position that pollution prevention evaluations at the front end of a project or process will reduce pollution on the back end

Primordial Noble Gases from Earth's Core

Science.gov (United States)

Wang, K.; Lu, X.; Brodholt, J. P.

2016-12-01

Recent partitioning experiment suggests helium is more compatible in iron melt than in molten silicates at high pressures (> 10 GPa) (1), thus provide the possibility of the core as being the primordial noble gases warehouse that is responsible for the high primordial/radiogenic noble gas isotopic ratios observed in plume-related basalts. However, the possible transportation mechanism of the noble gases from the core to the overlying mantle is still ambiguous, understanding how this process would affect the noble gas isotopic characteristics of the mantle is critical to validate this core reservoir model. As diffusion is a dominant mass transport process that plays an important role in chemical exchange at the core-mantle boundary (CMB), we have determined the diffusion coefficients of helium, neon and argon in major lower mantle minerals, i.e. periclase (MgO), bridgemanite (MgSiO3-Pv) and post-perovskite (MgSiO3-PPv), by first-principles calculation based on density functional theory (DFT). As expected, the diffusion rate of helium is the fastest at the CMB, which is in the range of 3 × 10-10 to 1 × 10-8 m2/s. The neon diffusion is slightly slower, from 5 × 10-10 to 5 × 10-9 m2/s. Argon diffuses slowest at the rate from 1 × 10-10 to 2 × 10-10 m2/s. We have further simulated the evolution of noble gas isotopic ratios in the mantle near the CMB. Considering its close relationship with the mantle plumes and very likely to be the direct source of "hot-spot" basalts, we took a close investigation on the large low-shear-velocity provinces (LLSVPs). Under reasonable assumptions based on our diffusion parameters, the modelling results indicate that LLSVP is capable of generating all the noble gas isotope signals, e.g., 3He/4He = 55 Ra, 3He/22Ne = 3.1, 3He/36Ar = 0.82, 40Ar/36Ar = 9500, that are in good agreement with the observed values in "hot-spot" basalts (2). Therefore, this core-reservior hypothesis is a self-consistent model that can fits in multiple noble gas

Beat my bass, pluck my drum

NARCIS (Netherlands)

Hengeveld, B.J.; Funk, M.; Doing, V.

2014-01-01

Beating a bass, plucking a drum -- new systems of instruments make it possible. In this paper we describe recent research into networked musical instruments for group improvisation; instruments that reciprocally influence each other's behaviour, making, contrary to what we are used to, the

Corrosion of steel drums containing simulated radioactive waste of low and intermediate level

International Nuclear Information System (INIS)

Farina, S.B.; Schulz Rodríguez, F.; Duffó, G.S.

2013-01-01

Ion-exchange resins are frequently used during the operation of nuclear power plants and constitute radioactive waste of low and intermediate level. For the final disposal inside the repository the resins are immobilized by cementation and placed inside steel drums. The eventful contamination of the resins with aggressive species may cause corrosion problems to the drums. In order to assess the incidence of this phenomenon and to estimate the lifespan of the steel drums, in the present work, the corrosion susceptibility of steel drums in contact with cemented ion-exchange resins contaminated with different aggressive species was studied. The aggressive species studied were chloride ions (main ionic species of concern) and sulphate ions (produced during radiolysis of the cationic exchange-resins after cementation). The corrosion rate of the steel was monitored over a time period of 900 days and a chemical and morphological analysis of the corrosion products formed on the steel in each condition was performed. When applying the results obtained in the present work to estimate the corrosion depth of the drums containing the cemented radioactive waste after a period of 300 years (foreseen durability of the Low and Intermediate Level Radioactive Waste facility in Argentina), it was found that in the most unfavourable case (high chloride contamination), the corrosion penetration will be considerably lower than the thickness of the wall of the steel drums. (author)

Calculation of calibration factors and layout criteria for gamma scanning of waste drums from nuclear plants

International Nuclear Information System (INIS)

Inder Schmitten, W.; Sohnius, B.; Wehner, E.

1990-01-01

This paper present a procedure to calculate calibration factors for converting the measured gamma rate of waste drums into activity content and a layout and free release measurement criterion for waste drums. A computer program is developed that simulates drum scanning technique, which calculates calibration factors and eliminates laborious experimental measurements. The calculated calibration factors exhibit good agreement with experimentally determined values. By checking the calculated calibration factors for trial equipment layouts (including the waste drum and the scanning facility) using the layout and free release measurement criterion, a layout can be achieved that clearly determines whether there can be free release of a waste drum

Noble gas atoms as chemical impurities in silicon

International Nuclear Information System (INIS)

Tkachev, V.D.; Mudryi, A.V.; Minaev, N.S.

1984-01-01

The behaviour of noble gas atoms implanted in silicon is studied by the luminescence method. The energy position of Moessbauer-type luminescence bands with zero-phonon lines 1.0148, 1.0120, 1.0097, 1.0048 eV and others connected with implanted atoms of neon, helium, argon, krypton, respectively, indicates the formation of deep energy levels in the forbidden gap of silicon. Implantation of the noble gas isotopes confirms their participation in formation processes of the luminescence centers in silicon. The temperature range of existence and the symmetry of defects incorporating the noble gas atoms are found. It is noted that noble gas atoms form impurity complexes with deep energy levels and their behaviour in crystals does not differ from that of main doped or residual technological impurity atoms. (author)

Equipment for capping drums, especially with radioactive waste

International Nuclear Information System (INIS)

Bednarik, F.

1987-01-01

The equipment consists of a pneumatic cylinder, lever systems with jaws, guide bars, and of securing pins. The top cylinder lid and the bottom cylinder lid provided with openings are slidably attached to a shaft firmly connected to a piston and a support plate. Firmly attached to the bottom lid using brackets are pins holding connecting rods controlling the double-arm levers pivoted on pins, featuring jaws pivoted on forks firmly attached to the support plate and provided with a replaceable spacer insert. The guide bars are firmly attached to the support plate via braces and stiffeners. The securing pins are loaded with springs seated in the braces. The benefits of the equipment include that the lid closing levers with jaws, mechanically controlled using one pneumatic cylinder, thanks to their number and configuration, close the lid around the drum border provided with small recesses which do not reach above the circumference of the drum being closed. The equipment can also be used for carrying closed drums, this also during compressed air failures because the levers with jaws are secured in position with the pneumatic cylinder leg. (J.B.). 1 fig

A-Ha. Drum'n'bassi supernimi FABIO

Index Scriptorium Estoniae

2002-01-01

7.sept. annab norra menukaim popansambel A-Ha Tallinnas Lauluväljakul kontserdi, kus presenteerib ka oma viimast albumit "Lifelines". 14. sept.tuleb drum'n'bassi spetsialist Fabio Tallinna üritusele Circulation

Analysis, scale modeling, and full-scale tests of low-level nuclear-waste-drum response to accident environments

International Nuclear Information System (INIS)

Huerta, M.; Lamoreaux, G.H.; Romesberg, L.E.; Yoshimura, H.R.; Joseph, B.J.; May, R.A.

1983-01-01

This report describes extensive full-scale and scale-model testing of 55-gallon drums used for shipping low-level radioactive waste materials. The tests conducted include static crush, single-can impact tests, and side impact tests of eight stacked drums. Static crush forces were measured and crush energies calculated. The tests were performed in full-, quarter-, and eighth-scale with different types of waste materials. The full-scale drums were modeled with standard food product cans. The response of the containers is reported in terms of drum deformations and lid behavior. The results of the scale model tests are correlated to the results of the full-scale drums. Two computer techniques for calculating the response of drum stacks are presented. 83 figures, 9 tables

Chipping machines: disc and drum energy requirements

Directory of Open Access Journals (Sweden)

Alessio Facello

2013-09-01

Full Text Available Air pollution and fossil fuel reserves exhaustion are increasing the importance of the biomass-derived products, in particular wood, as source of clean and renewable energy for the production of electricity or steam. In order to improve the global efficiency and the entire production chain, we have to evaluate the energetic aspects linked to the process of transformation, handling and transport of these materials. This paper reports results on a comparison between two chippers of similar size using different cutting technology: disc and drum tool respectively. During trials, fuel consumption, PTO torque and speed, processing time and weight of processed material were recorded. Power demand, fuel consumption, specific energy and productivity were computed. The machine was fed with four different feedstock types (chestnut logs, poplar logs, poplar branches, poplar sawmill residues. 15 repetitions for each combination of feedstock-tool were carried out. The results of this study show that the disc tool requires, depending on the processed material, from 12 to 18% less fuel per unit of material processed than the drum tool, and consequently, from 12 to 16% less specific energy. In particular, the highest difference between tools was found in branches processing whereas the smallest was in poplar logs. Furthermore the results of the investigation indicate, that, in testing conditions, the productivity of drum tool is higher (8% than disc tool.

Europa Drum Sampler (EDuS), Phase I

Data.gov (United States)

National Aeronautics and Space Administration — The main objective of the proposed work is to develop a robust and effective sample acquisition system for the Europa lander called the Europa Drum Sampler (EDuS)....

Energy Cost of Active and Sedentary Music Video Games: Drum and Handheld Gaming vs. Walking and Sitting.

Science.gov (United States)

Miranda, Edwin; Overstreet, Brittany S; Fountain, William A; Gutierrez, Vincent; Kolankowski, Michael; Overstreet, Matthew L; Sapp, Ryan M; Wolff, Christopher A; Mazzetti, Scott A

2017-01-01

To compare energy expenditure during and after active and handheld video game drumming compared to walking and sitting. Ten experienced, college-aged men performed four protocols (one per week): no-exercise seated control (CTRL), virtual drumming on a handheld gaming device (HANDHELD), active drumming on drum pads (DRUM), and walking on a treadmill at ~30% of VO 2max (WALK). Protocols were performed after an overnight fast, and expired air was collected continuously during (30min) and after (30min) exercise. DRUM and HANDHELD song lists, day of the week, and time of day were identical for each participant. Significant differences (p DRUM > HANDHELD. No significant differences in the rates of energy expenditure among groups during recovery were observed. Total energy expenditure was significantly greater (p < 0.05) during WALK (149.5 ± 30.6 kcal) compared to DRUM (118.7 ± 18.8 kcal) and HANDHELD (44.9±11.6 kcal), and greater during DRUM compared to HANDHELD. Total energy expenditure was not significantly different between HANDHELD (44.9 ± 11.6 kcal) and CTRL (38.2 ± 6.0 kcal). Active video game drumming at expert-level significantly increased energy expenditure compared to handheld, but it hardly met moderate-intensity activity standards, and energy expenditure was greatest during walking. Energy expenditure with handheld video game drumming was not different from no-exercise control. Thus, traditional aerobic exercise remains at the forefront for achieving the minimum amount and intensity of physical activity for health, individuals desiring to use video games for achieving weekly physical activity recommendations should choose games that require significant involvement of lower-body musculature, and time spent playing sedentary games should be a limited part of an active lifestyle.

MCNP Modeling Results for Location of Buried TRU Waste Drums

International Nuclear Information System (INIS)

Steinman, D K; Schweitzer, J S

2006-01-01

In the 1960's, fifty-five gallon drums of TRU waste were buried in shallow pits on remote U.S. Government facilities such as the Idaho National Engineering Laboratory (now split into the Idaho National Laboratory and the Idaho Completion Project [ICP]). Subsequently, it was decided to remove the drums and the material that was in them from the burial pits and send the material to the Waste Isolation Pilot Plant in New Mexico. Several technologies have been tried to locate the drums non-intrusively with enough precision to minimize the chance for material to be spread into the environment. One of these technologies is the placement of steel probe holes in the pits into which wireline logging probes can be lowered to measure properties and concentrations of material surrounding the probe holes for evidence of TRU material. There is also a concern that large quantities of volatile organic compounds (VOC) are also present that would contaminate the environment during removal. In 2001, the Idaho National Engineering and Environmental Laboratory (INEEL) built two pulsed neutron wireline logging tools to measure TRU and VOC around the probe holes. The tools are the Prompt Fission Neutron (PFN) and the Pulsed Neutron Gamma (PNG), respectively. They were tested experimentally in surrogate test holes in 2003. The work reported here estimates the performance of the tools using Monte-Carlo modelling prior to field deployment. A MCNP model was constructed by INEEL personnel. It was modified by the authors to assess the ability of the tools to predict quantitatively the position and concentration of TRU and VOC materials disposed around the probe holes. The model was used to simulate the tools scanning the probe holes vertically in five centimetre increments. A drum was included in the model that could be placed near the probe hole and at other locations out to forty-five centimetres from the probe-hole in five centimetre increments. Scans were performed with no chlorine in the

Press to compress contaminated wastes drums

International Nuclear Information System (INIS)

Prevost, J.

1993-01-01

This patent describes a press for contaminated wastes drums pressing. The press is made of a structure comprising a base and an upper stringer bind to the base by vertical bearers, a compression system comprising a main cylinder and a ram, connected to the upper stringer

A Markov chain analysis of the effectiveness of drum-buffer-rope material flow management in job shop environment

Directory of Open Access Journals (Sweden)

Masoud Rabbani

2015-09-01

Full Text Available The theory of constraints is an approach for production planning and control, which emphasizes on the constraints in the system to increase throughput. The theory of constraints is often referred to as Drum-Buffer-Rope developed originally by Goldratt. Drum-Buffer-Rope uses the drum or constraint to create a schedule based on the finite capacity of the first bottleneck. Because of complexity of the job shop environment, Drum-Buffer-Rope material flow management has very little attention to job shop environment. The objective of this paper is to apply the Drum-Buffer-Rope technique in the job shop environment using a Markov chain analysis to compare traditional method with Drum-Buffer-Rope. Four measurement parameters were considered and the result showed the advantage of Drum-Buffer-Rope approach compared with traditional one.

Application of the Monte Carlo method to estimate doses in a radioactive waste drum environment

International Nuclear Information System (INIS)

Rodenas, J.; Garcia, T.; Burgos, M.C.; Felipe, A.; Sanchez-Mayoral, M.L.

2002-01-01

During refuelling operation in a Nuclear Power Plant, filtration is used to remove non-soluble radionuclides contained in the water from reactor pool. Filter cartridges accumulate a high radioactivity, so that they are usually placed into a drum. When the operation ends up, the drum is filled with concrete and stored along with other drums containing radioactive wastes. Operators working in the refuelling plant near these radwaste drums can receive high dose rates. Therefore, it is convenient to estimate those doses to prevent risks in order to apply ALARA criterion for dose reduction to workers. The Monte Carlo method has been applied, using MCNP 4B code, to simulate the drum containing contaminated filters and estimate doses produced in the drum environment. In the paper, an analysis of the results obtained with the MCNP code has been performed. Thus, the influence on the evaluated doses of distance from drum and interposed shielding barriers has been studied. The source term has also been analysed to check the importance of the isotope composition. Two different geometric models have been considered in order to simplify calculations. Results have been compared with dose measurements in plant in order to validate the calculation procedure. This work has been developed at the Nuclear Engineering Department of the Polytechnic University of Valencia in collaboration with IBERINCO in the frame of an RD project sponsored by IBERINCO

Noble Metal Nanoparticles for Biosensing Applications

Directory of Open Access Journals (Sweden)

Pedro V. Baptista

2012-02-01

Full Text Available In the last decade the use of nanomaterials has been having a great impact in biosensing. In particular, the unique properties of noble metal nanoparticles have allowed for the development of new biosensing platforms with enhanced capabilities in the specific detection of bioanalytes. Noble metal nanoparticles show unique physicochemical properties (such as ease of functionalization via simple chemistry and high surface-to-volume ratios that allied with their unique spectral and optical properties have prompted the development of a plethora of biosensing platforms. Additionally, they also provide an additional or enhanced layer of application for commonly used techniques, such as fluorescence, infrared and Raman spectroscopy. Herein we review the use of noble metal nanoparticles for biosensing strategies—from synthesis and functionalization to integration in molecular diagnostics platforms, with special focus on those that have made their way into the diagnostics laboratory.

DRUMS: a human disease related unique gene mutation search engine.

Science.gov (United States)

Li, Zuofeng; Liu, Xingnan; Wen, Jingran; Xu, Ye; Zhao, Xin; Li, Xuan; Liu, Lei; Zhang, Xiaoyan

2011-10-01

With the completion of the human genome project and the development of new methods for gene variant detection, the integration of mutation data and its phenotypic consequences has become more important than ever. Among all available resources, locus-specific databases (LSDBs) curate one or more specific genes' mutation data along with high-quality phenotypes. Although some genotype-phenotype data from LSDB have been integrated into central databases little effort has been made to integrate all these data by a search engine approach. In this work, we have developed disease related unique gene mutation search engine (DRUMS), a search engine for human disease related unique gene mutation as a convenient tool for biologists or physicians to retrieve gene variant and related phenotype information. Gene variant and phenotype information were stored in a gene-centred relational database. Moreover, the relationships between mutations and diseases were indexed by the uniform resource identifier from LSDB, or another central database. By querying DRUMS, users can access the most popular mutation databases under one interface. DRUMS could be treated as a domain specific search engine. By using web crawling, indexing, and searching technologies, it provides a competitively efficient interface for searching and retrieving mutation data and their relationships to diseases. The present system is freely accessible at http://www.scbit.org/glif/new/drums/index.html. © 2011 Wiley-Liss, Inc.

Electric-stepping-motor tests for a control-drum actuator of a nuclear reactor

Science.gov (United States)

Kieffer, A. W.

1972-01-01

Experimental tests were conducted on two stepping motors for application as reactor control-drum actuators. Various control-drum loads with frictional resistances ranging from approximately zero to 40 N-m and inertias ranging from zero to 0.424 kg-sq m were tested.

Handling 78,000 drums of mixed-waste sludge

International Nuclear Information System (INIS)

Berry, J.B.; Gilliam, T.M.; Harrington, E.S.; Youngblood, E.L.; Baer, M.B.

1991-01-01

The Oak Ridge Gaseous Diffusion Plant (now know as the Oak Ridge K-25 Site) prepared two mixed-waste surface impoundments for closure by removing the sludge and contaminated pond-bottom clay and attempting to process it into durable, nonleachable, concrete monoliths. Interim, controlled, above-ground storage of the stabilized waste was planned until final disposition. The strategy for disposal included delisting the stabilized pond sludge from hazardous to nonhazardous and disposing of the delisted monoliths as radioactive waste. Because of schedule constraints and process design and control deficiencies, ∼46,000 drums of material in various stages of solidification and ∼32,000 drums of unprocessed sludge are presently being stored. In addition, the abandoned treatment facility still contains ∼16,000 gal of raw sludge. Such conditions do not comply with the requirements set forth by the Resource Conservation and Recovery Act (RCRA) for the storage of listed waste. Various steps are being taken to bring the storage of ∼78,000 drums of mixed waste into compliance with RCRA. This paper (1) reviews the current situation, (2) discusses the plan for remediation of regulatory noncompliances, including decanting liquid from stabilized waste and dewatering untreated waste, and (3) provides an assessment of alternative raw-waste treatment processes. 1 ref., 6 figs., 2 tabs

Noble gases recycled into the mantle through cold subduction zones

Science.gov (United States)

Smye, Andrew J.; Jackson, Colin R. M.; Konrad-Schmolke, Matthias; Hesse, Marc A.; Parman, Steve W.; Shuster, David L.; Ballentine, Chris J.

2017-08-01

Subduction of hydrous and carbonated oceanic lithosphere replenishes the mantle volatile inventory. Substantial uncertainties exist on the magnitudes of the recycled volatile fluxes and it is unclear whether Earth surface reservoirs are undergoing net-loss or net-gain of H2O and CO2. Here, we use noble gases as tracers for deep volatile cycling. Specifically, we construct and apply a kinetic model to estimate the effect of subduction zone metamorphism on the elemental composition of noble gases in amphibole - a common constituent of altered oceanic crust. We show that progressive dehydration of the slab leads to the extraction of noble gases, linking noble gas recycling to H2O. Noble gases are strongly fractionated within hot subduction zones, whereas minimal fractionation occurs along colder subduction geotherms. In the context of our modelling, this implies that the mantle heavy noble gas inventory is dominated by the injection of noble gases through cold subduction zones. For cold subduction zones, we estimate a present-day bulk recycling efficiency, past the depth of amphibole breakdown, of 5-35% and 60-80% for 36Ar and H2O bound within oceanic crust, respectively. Given that hotter subduction dominates over geologic history, this result highlights the importance of cooler subduction zones in regassing the mantle and in affecting the modern volatile budget of Earth's interior.

Detection of free liquid in cement-solidified radioactive waste drums using computed tomography

International Nuclear Information System (INIS)

Steude, J.S.; Tonner, P.D.

1991-01-01

Acceptance criteria for disposal of radioactive waste drums require that the cement-solidified material in the drum contain minimal free liquid after the cement has hardened. Free liquid is to be avoided because it may corrode the drum, escape and cause environmental contamination. The DOE has requested that a nondestructive evaluation method be developed to detect free liquid in quantities in excess of 0.5% by volume. This corresponds to about 1 liter in a standard 208 liter (55 gallon) drum. In this study, the detection of volumes of free liquid in a 57 cm (2 ft.) diameter cement-solidified drum is demonstrated using high-energy X-ray computed tomography (CT0. In this paper it is shown that liquid concentrations of simulated radioactive waste inside glass tubes imbedded in cement can easily be detected, even for tubes with inner diameters less than 2 mm (0.08 in.). Furthermore, it is demonstrated that tubes containing water and liquid concentrations of simulated radioactive waste can be distinguished from tubes of the same size containing air. The CT images were obtained at a rate of about 6 minutes per slice on a commercially available CT system using a 9 MeV linear accelerator source

Nuclear waste calorimeter for very large drums with 385 litres sample volume

Energy Technology Data Exchange (ETDEWEB)

Jossens, G.; Mathonat, C. [SETARAM Instrumentation, Caluire (France); Bachelet, F. [CEA Valduc, Is sur Tille (France)

2015-03-15

Calorimetry is a very precise and well adapted tool for the classification of drums containing nuclear waste material depending on their level of activities (low, medium, high). A new calorimeter has been developed by SETARAM Instrumentation and the CEA Valduc in France. This new calorimeter is designed for drums having a volume bigger than 100 liters. It guarantees high operator safety by optimizing drum handling and air circulation for cooling, and optimized software for direct measurement of the quantity of nuclear material. The LVC1380 calorimeter makes it possible to work over the range 10 to 3000 mW, which corresponds to approximately 0.03 to 10 g of tritium or 3 to 955 g of {sup 241}Pu in a volume up to 385 liters. This calorimeter is based on the heat flow measurement using Peltier elements which surround the drum in the 3 dimensions and therefore measure all the heat coming from the radioactive stuff whatever its position inside the drum. Calorimeter's insulating layers constitute a thermal barrier designed to filter disturbances until they represent less than 0.001 Celsius degrees and to eliminate long term disturbances associated, for example, with laboratory temperature variations between day and night. A calibration device based on Joule effect has also been designed. Measurement time has been optimized but remains long compared with other methods of measurement such as gamma spectrometry but its main asset is to have a good accuracy for low level activities.

Space-DRUMS trade mark sign experimental development using parabolic reduced gravity flights

International Nuclear Information System (INIS)

Guigne, J.Y.; Millan, D.; Davidson, R.

2000-01-01

Space-DRUMS trade mark sign is a microgravity containerless-processing facility that uses acoustic beams to position large diameter liquid or solid samples within a gas-filled chamber. Its capacity to control the position of large diameter (6 cm) low density solid materials was successfully demonstrated on NASA's DC-9 parabolic aircraft in July 1996; two subsequent flights occurred in 1998 using the KC-135 and A-300 aircraft to further refine the technology used in the system. The working environment for the Space-DRUMS trade mark sign facility is the Space Shuttle/Space Station where long duration microgravity experimentation can take place. Since the reduced gravity environment of an A-300 or a KC-135 parabolic flight is much harsher than that of the Space Shuttle in terms of residual acceleration magnitudes experienced by the samples to be held in position; this more extreme environment allows for most Space-DRUMS trade mark sign technical payload functionality tests to be conducted. In addition to flight hardware shakedowns, parabolic flights continue to be extensively used to study and evaluate the behavior of candidate-advanced materials proposed for ISS Space-DRUMS trade mark sign campaigns. The first samples to be processed in 2001 involve combustion synthesis (also known as SHS - Self-propagating High Temperature Synthesis) of large glass-ceramic and of porous ceramic spheres. Upmassing Space-DRUMS trade mark sign for the International Space Station is scheduled for early 2001

Monitoring of noble gas radioisotopes in nuclear power plant effluents

International Nuclear Information System (INIS)

Kabat, M.J.

1985-01-01

Monitoring of gaseous radionuclides in the effluents of nuclear facilities is an essential requirement in effluent management programs. Since there is no practical way of removing noble gas radioisotopes from air at release pathways, their accurate monitoring is essential for providing appropriate environmental protection. Emitted γ dose-rate is the limiting factor for concentration-time integral of noble gas in gaseous effluents of reactor facilities. The external exposure to the public from a semi-infinite cloud is directly proportional to both the noble gas isotope concentration and the integrated γ energy per disintegration. Both can be directly measured in gaseous effluent pathways with a suitable detector. The capability of NaI(T1), CaF 2 (Eu) and plastic scintillation detectors to measure the γ-Ci.MeV content of noble gas releases was experimentally evaluated. The combination of CaF 2 (Eu) detector in a pressurized through-flow chamber, with a charge integrating scaler well complied with both γ energy response and detection sensitivity requirements. Noble gas source terms and effluent monitoring criteria are discussed, theoretical and experimental results are presented and a practical, on-line noble gas monitoring system is described

Magneto-optical Kerr spectroscopy of noble metals

Science.gov (United States)

Uba, L.; Uba, S.; Antonov, V. N.

2017-12-01

Magneto-optical (MO) response of the noble metals Cu, Ag, and Au in the joint experimental and ab initio theoretical study is reported. The magneto-optical polar Kerr effect (MOKE) spectra of the noble-metal films were measured with the high sensitivity in the applied magnetic field of 1.5 T over the photon energy range 0.74-5.8 eV. Complete set of the optical conductivity tensor elements was determined precisely from the MOKE and the optical spectra measured at the same energy points. The importance of the off-diagonal intraband Drude-type transitions is demonstrated explicitly for each noble metal and found to be a substantial contribution to the observed spectra. It is shown that the first-principles calculations using the spin-polarized fully relativistic Dirac linear-muffin-tin-orbital method with the inclusion of correlation effects by GGA+U approach reproduce well the experimental spectra and allow to explain the microscopic origin of the noble metals' magneto-optical response in terms of interband transitions. Although the energy band structures of Cu, Ag, and Au are very similar, there are some distinctive differences in bandwidths and the energy positions of the bands (especially in X and L symmetry points), mainly due to different spin-orbit splitting and differences in the spatial extent of 3 d , 4 d , and 5 d valence wave functions of noble metals. It was found that the small differences in the band positions lead to significant differences in the MO properties of three noble metals. Although the spin-orbit interaction in Au is about six times larger than in Cu, and approximately two times larger than in Ag, the absolute value of Kerr rotation in Au is of the same magnitude as in Cu and one order of magnitude smaller as compared to Ag. The sharp Kerr effect spectral peak in Ag is not due to the electronic interband transitions, but rather to the plasma-edge splitting. The band-by-band decomposition of the Cu, Ag, and Au MO spectra is presented and the

Real-time radiography, digital radiography, and computed tomography for nonintrusive waste drum characterization

International Nuclear Information System (INIS)

Martz, H.E.; Schneberk, D.J.; Roberson, G.P.

1994-07-01

We are investigating and developing the application of x-ray nondestructive evaluation (NDE) and gamma-ray nondestructive assay (NDA) methods to nonintrusively characterize 208-liter (55-gallon) mixed waste drums. Mixed wastes contain both hazardous and radioactive materials. We are investigating the use of x-ray NDE methods to verify the content of documented waste drums and determine if they can be used to identify hazardous and nonconforming materials. These NDE methods are also being used to help waste certification and hazardous waste management personnel at LLNL to verify/confirm and/or determine the contents of waste. The gamma-ray NDA method is used to identify the intrinsic radioactive source(s) and to accurately quantify its strength. The NDA method may also be able to identify some hazardous materials such as heavy metals. Also, we are exploring techniques to combine both NDE and NDA data sets to yield the maximum information from these nonintrusive, waste-drum characterization methods. In this paper, we report an our x-ray NDE R ampersand D activities, while our gamma-ray NDA activities are reported elsewhere in the proceedings. We have developed a data, acquisition scanner for x-ray NDE real-time radiography (RTR), as well as digital radiography transmission computed tomography (TCT) along with associated computational techniques for image reconstruction, analysis, and display. We are using this scanner and real-waste drums at Lawrence Livermore National Laboratory (LLNL). In this paper, we discuss some issues associated with x-ray imaging, describe the design construction of an inexpensive NDE drum scanner, provide representative DR and TCT results of both mock- and real-waste drums, and end with a summary of our efforts and future directions. The results of these scans reveal that RTR, DR, and CT imaging techniques can be used in concert to provide valuable information about the interior of low-level-, transuranic-, and mock-waste drums without

Composition and activity variations in bulk gas of drum waste packages of Paks NPP

International Nuclear Information System (INIS)

Molnar, M.; Palcsu, L.; Svingor, E.; Szanto, Zs.; Futo, I.; Ormai, P.

2001-01-01

To obtain reliable estimates of the quantities and rates of the gas production a series of measurements was carried out in drum waste packages generated and temporarily stored at the site of Paks Nuclear Power Plant (Paks NPP). Ten drum waste packages were equipped with sampling valves for repeated sampling. Nine times between 04/02/2000 and 19/07/2001 qualitative gas component analyses of bulk gases of drums were executed. Gas samples were delivered to the laboratory of the ATOMKI for tritium and radiocarbon content measurements.(author)

Infrared thermography applied to monitoring of radioactive waste drums; Termografia infravermelha aplicada ao monitoramento de tambores de rejeitos radioativos

Energy Technology Data Exchange (ETDEWEB)

Kelmer, P.; Camarano, D.M. [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil); Calado, F.; Phillip, B.; Viana, C.; Andrade, R.M., E-mail: paulafuziki@yahoo.com.br, E-mail: flavio.arcalado@gmail.com, E-mail: bruno.phil@gmail.com, E-mail: criisviana@hotmail.com, E-mail: rma@ufmg.br, E-mail: dmc@cdtn.br [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil). Departamento de Engenharia Eletrica

2013-07-01

The use of thermography in the inspection of drums containing radioactive waste is being stimulated by the absence of physical contact. In Brazil the majority of radioactive wastes are compacted solids packed in metal drums stored temporarily for decades and requires special attention. These drums have only one qualitative indication of the radionuclides present. However, its structural condition is not followed systematically. The aim of this work is presents a methodology by applying thermography for monitoring the structural condition of drums containing radioactive waste in order to detect degraded regions of the drums. (author)

Low-Level Waste Drum Assay Intercomparison Study

International Nuclear Information System (INIS)

Greutzmacher, K.; Kuzminski, J.; Myers, S. C.

2003-01-01

Nuclear waste assay is an integral element of programs such as safeguards, waste management, and waste disposal. The majority of nuclear waste is packaged in drums and analyzed by various nondestructive assay (NDA) techniques to identify and quantify the radioactive content. Due to various regulations and the public interest in nuclear issues, the analytical results are required to be of high quality and supported by a rigorous Quality Assurance (QA) program. A valuable QA tool is an intercomparison program in which a known sample is analyzed by a number of different facilities. While transuranic waste (TRU) certified NDA teams are evaluated through the Performance Demonstration Program (PDP), low-level waste (LLW) assay specialists have not been afforded a similar opportunity. NDA specialists from throughout the DOE complex were invited to participate in this voluntary drum assay intercomparison study that was organized and facilitated by the Solid Waste Operations and the Safeguards Science and Technology groups at the Los Alamos National Laboratory and by Eberline Services. Each participating NDA team performed six replicate blind measurements of two 55-gallon drums with relatively low-density matrices (a 19.1 kg shredded paper matrix and a 54.4 kg mixed metal, rubber, paper and plastic matrix). This paper presents the results from this study, with an emphasis on discussing the lessons learned as well as desirable follow up programs for the future. The results will discuss the accuracy and precision of the replicate measurements for each NDA team as well as any issues that arose during the effort

Special closures for steel drum shipping containers

International Nuclear Information System (INIS)

Bonzon, L.L.; Otts, J.V.

1976-01-01

The objective of this program was to develop special lid closures for typical, steel drum, radioactive material shipping containers. Previous experience and testing had shown that the existing container was adequate to withstand the required environmental tests for certification, but that the lid and closure were just marginally effective. Specifically, the lid closure failed to consistently maintain a tight seal between the container and the lid after drop tests, thus causing the package contents to be vulnerable in the subsequent fire test. Recognizing the deficiency, the United States Energy Research and Development Administration requested the development of new closure(s) which would: (1) be as strong and resistant to a drop as the bottom of the container; (2) have minimal economic impact on the overall container cost; (3) maximize the use of existing container designs; (4) consider crush loads; and (5) result in less dependence on personnel and loading procedures. Several techniques were evaluated and found to be more effective than the standard closure mechanism. Of these, three new closure techniques were designed, fabricated, and proven to be structurally adequate to provide containment when a 454-kg drum was drop tested from 9.14-m onto an unyielding surface. The three designs were: (1) a 152-mm long lid extension or skirt welded to the standard drum lid, (2) a separate inner lid, with 152-mm long skirt and (3) C-clamps used at the container-lid interface. Based upon structural integrity, economic impact, and minimal design change, the lid extension is the recommended special closure

Determination of natural in vivo noble-gas concentrations in human blood.

Directory of Open Access Journals (Sweden)

Yama Tomonaga

Full Text Available Although the naturally occurring atmospheric noble gases He, Ne, Ar, Kr, and Xe possess great potential as tracers for studying gas exchange in living beings, no direct analytical technique exists for simultaneously determining the absolute concentrations of these noble gases in body fluids in vivo. In this study, using human blood as an example, the absolute concentrations of all stable atmospheric noble gases were measured simultaneously by combining and adapting two analytical methods recently developed for geochemical research purposes. The partition coefficients determined between blood and air, and between blood plasma and red blood cells, agree with values from the literature. While the noble-gas concentrations in the plasma agree rather well with the expected solubility equilibrium concentrations for air-saturated water, the red blood cells are characterized by a distinct supersaturation pattern, in which the gas excess increases in proportion to the atomic mass of the noble-gas species, indicating adsorption on to the red blood cells. This study shows that the absolute concentrations of noble gases in body fluids can be easily measured using geochemical techniques that rely only on standard materials and equipment, and for which the underlying concepts are already well established in the field of noble-gas geochemistry.

Intelligent mobile sensor system for drum inspection and monitoring: Phase 1

International Nuclear Information System (INIS)

1993-06-01

The objective of this project was to develop an operational system for monitoring and inspection activities for waste storage facility operations at several DOE sites. Specifically, the product of this effort is a robotic device with enhanced intelligence and maneuverability capable of conducting routine inspection of stored waste drums. The device is capable of operating in narrow aisles and interpolating the free aisle space between rows of stacked drums. The system has an integrated sensor suite for leak detection, and is interfaced with a site database both for inspection planning and for data correlation, updating, and report generation. The system is capable of departing on an assigned mission, collecting required data, recording which positions of its mission had to be aborted or modified due to environmental constraints, and reporting back when the mission is complete. Successful identification of more than 90% of all drum defects has been demonstrated in a high fidelity waste storage facility mockup. Identified anomalies included rust spots, rust streaks, areas of corrosion, dents, and tilted drums. All drums were positively identified and correlated with the site database. This development effort is separated into three phases of which phase one is now complete. The first phase has demonstrated an integrated system for monitoring and inspection activities for waste storage facility operations. This demonstration system was quickly fielded and evaluated by leveraging technologies developed from previous NASA and DARPA contracts and internal research. The second phase will demonstrate a prototype system appropriate for operational use in an actual storage facility. The prototype provides an integrated design that considers operational requirements, hardware costs, maintenance, safety, and robustness. The final phase will demonstrate commercial viability using the prototype vehicle in a pilot waste operations and inspection project

International Conference on LIght Detection in Noble Elements

CERN Document Server

2016-01-01

The objective of the Light Detection in Noble Elements (LIDINE) 2015 conference is to promote discussion between the members of the particle and nuclear physics communities about light and charge collection in detectors based on liquid or gaseous noble elements, xenon and argon being the most common, but neon and helium also in use, and represented at this conference. The neutrino physics, ultra-cold neutron study, dark matter search, and medical physics communities all utilize noble-based detector technologies, recording UV scintillation and/or ionization. Therefore, this will be an interdisciplinary opportunity for information exchange, and a chance for each of these communities enumerated above, in the U.S. as well as abroad, to expand their technical knowledge bases.

Noble gas absorption process

International Nuclear Information System (INIS)

Thomas, J.W.

1975-01-01

A method of removing a noble gas from air comprising the use of activated carbon filters in stages in which absorption and desorption steps in succession are conducted in order to increase the capacity of the filters is described. (U.S.)

The Saami drums and the religious encounter in the 17th and 18th centuries

Directory of Open Access Journals (Sweden)

Håkan Rydving

1991-01-01

Full Text Available From the end of the 17th to the middle of the 18th century much of the confrontation between indigenous Saami religion and Christianity was focused on the drums. The Saamis of both Denmark—Norway and Sweden—Finland had been christianized for decade. The main problem for the Church authorities turned out to be that of making the Saamis abandon their indigenous religious customs. From the end of the 17th century, an intense period of propaganda and coercion began to make the Saamis abandon these non Christian elements in their religion. For the Saamis, the drums represented their threatened culture, the resistance against the Christian claim to exclusiveness, and a striving to preserve traditional values. The drums had a twofold role to play in the religious encounter. They were both foci of the confrontation and sources documenting and structuring it. The fight between old and new beliefs is to some extent possible to follow in the records from the district and county courts. These records give us access to Saami arguments and views of the importance of the drums in Saami society. The function of the drums as instruments for a Saami description of the encounter is, however, difficult to make out. The drum figures are difficult to interpret and there are a number of alternative ways of understanding their meaning.

Analysis of force variance for a continuous miner drum using the Design of Experiments method

Energy Technology Data Exchange (ETDEWEB)

S. Somanchi; V.J. Kecojevic; C.J. Bise [Pennsylvania State University, University Park, PA (United States)

2006-06-15

Continuous miners (CMs) are excavating machines designed to extract a variety of minerals by underground mining. The variance in force experienced by the cutting drum is a very important aspect that must be considered during drum design. A uniform variance essentially means that an equal load is applied on the individual cutting bits and this, in turn, enables better cutting action, greater efficiency, and longer bit and machine life. There are certain input parameters used in the drum design whose exact relationships with force variance are not clearly understood. This paper determines (1) the factors that have a significant effect on the force variance of the drum and (2) the values that can be assigned to these factors to minimize the force variance. A computer program, Continuous Miner Drum (CMD), was developed in collaboration with Kennametal, Inc. to facilitate the mechanical design of CM drums. CMD also facilitated data collection for determining significant factors affecting force variance. Six input parameters, including centre pitch, outer pitch, balance angle, shift angle, set angle and relative angle were tested at two levels. Trials were configured using the Design of Experiments (DoE) method where 2{sup 6} full-factorial experimental design was selected to investigate the effect of these factors on force variance. Results from the analysis show that all parameters except balance angle, as well as their interactions, significantly affect the force variance.

Non-intrusive measurement of tritium activity in waste drums by modelling a 3He leak quantified by mass spectrometry

International Nuclear Information System (INIS)

Demange, D.

2002-01-01

This study deals with a new method that makes it possible to measure very low tritium quantities inside radioactive waste drums. This indirect method is based on measuring the decaying product, 3 He, and requires a study of its behaviour inside the drum. Our model considers 3 He as totally free and its leak through the polymeric joint of the drum as two distinct phenomena: permeation and laminar flow. The numerical simulations show that a pseudo-stationary state takes place. Thus, the 3 He leak corresponds to the tritium activity inside the drum but it appears, however, that the leak peaks when the atmospheric pressure variations induce an overpressure in the drum. Nevertheless, the confinement of a drum in a tight chamber makes it possible to quantify the 3 He leak. This is a non-intrusive measurement of its activity, which was experimentally checked by using reduced models, representing the drum and its confinement chamber. The drum's confinement was optimised to obtain a reproducible 3 He leak measurement. The gaseous samples taken from the chamber were purified using selective adsorption onto activated charcoals at 77 K to remove the tritium and pre-concentrate the 3 He. The samples were measured using a leak detector mass spectrometer. The adaptation of the signal acquisition and the optimisation of the analysis parameters made it possible to reach the stability of the external calibrations using standard gases with a 3 He detection limit of 0.05 ppb. Repeated confinement of the reference drums demonstrated the accuracy of this method. The uncertainty of this non-intrusive measurement of the tritium activity in 200-liter drums is 15% and the detection limit is about 1 GBq after a 24 h confinement. These results led to the definition of an automated tool able to systematically measure the tritium activity of all storage waste drums. (authors)

Field test results for radioactive waste drum characterization with Waste Inspection Tomography (WIT)

Energy Technology Data Exchange (ETDEWEB)

Bernardi, R.T. [Bio-Imaging Research, Inc., Lincolnshire, IL (United States)

1997-11-01

This paper summarizes the design, fabrication, factory testing, evaluation and demonstration of waste inspection tomography (WIT). WIT consists of a self-sufficient, mobile semi-trailer for Non-Destructive Evaluation and Non-Destructive Assay (NDE/NDA) characterization of nuclear waste drums using X-ray and gamma-ray tomographic techniques. The 23-month WIT Phase I initial test results include 2 MeV Digital Radiography (DR), Computed Tomography (CT), Anger camera imaging, Single Photon Emission Computed Tomography (SPECT), Gamma-Ray Spectroscopy, Collimated Gamma Scanning (CGS), and Active and Passive Computed Tomography (A&PCT) using a 1.4 mCi source of {sup 166}Ho. These techniques were initially demonstrated on a 55-gallon phantom drum with three simulated waste matrices of combustibles, heterogeneous metals, and cement using check sources of gamma active isotopes. Waste matrix identification, isotopic identification, and attenuation-corrected gamma activity determination were all demonstrated nondestructively and noninvasively. Preliminary field tests results with nuclear waste drums are summarized. WIT has inspected drums with 0 to 20 grams plutonium 239. The minimum measured was 0.131 gram plutonium 239 in cement. 8 figs.

Estimation of build up of dose rate on U3O8 product drum

International Nuclear Information System (INIS)

Pandey, J.P.N.; Shinde, A.M.; Deshpande, M.D.

2008-01-01

In fuel reprocessing plant, plutonium oxide and uranium oxide (U 3 O 8 ) are products. Approximately 180 kg U 3 O 8 is filled in SS drum and sealed firmly before storage. In PHWR natural uranium (UO 2 ) is used as fuel. In natural uranium, thorium-232 is present as an impurity at few tens of ppm level. During irradiation in power reactors, due to nuclear reaction formation of 232 U from 232 Th takes place. Natural decay of 232 U leads to the formation of 208 Tl. As time passes, there is buildup of 208 Tl and hence increase in dose rate on the drum containing U 3 O 8 . It is essential to estimate the buildup of dose rate considering the external radiological hazards involved during U 3 O 8 drum handling, transportation and fuel fabrication. This paper describes the calculation of dose rate on drum in future years using MCNP code. For dose rate calculation decay of fission product activity which remains as contamination in product and build up of '2 08 Tl from 232 U is considered. Some measured values of dose rate on U 3 O 8 drum are given for the comparisons with estimated dose rate based on MCNP code. (author)

Solubility investigations in support of ultrasensitive noble gas detector development

International Nuclear Information System (INIS)

Gross, K.C.; Andersen, A.; Russ, W.R.; Stuenkel, D.; Valentine, J.D.

1998-01-01

Argonne National Laboratory (ANL) and the University of Cincinnati (UC) have been developing a new class of ultrasensitive noble gas detectors that are based upon the ANL discovery that corn oil has a high affinity for heavy noble gas absorption at room temperature but releases the noble gases with warming or by other low-energy-input means. Environmental applications for this new class of fluid-based detectors include ultrahigh sensitivity radioxenon detectors for comprehensive test ban treaty surveillance, improved fission gas detectors for enhanced environmental surveillance in the vicinity of US Department of Energy, US Department of Defense, and US Nuclear Regulatory Commission licensed facilities, and improved integrating Rn detectors for earthquake prediction. They present the results of theoretical and experimental investigations into the solubility phenomena of heavy noble gases (Rn, Xe, and Kr) in triglyceride oils. They intend for the findings presented herein to be used to guide future selection, development, and refinement of vegetable and other hydrocarbon oils to bring further enhancements to noble gas detection efficiencies

Solubility investigations in support of ultrasensitive noble gas detector development

International Nuclear Information System (INIS)

Gross, K. C.

1998-01-01

Argonne National Laboratory (ANL) and the University of Cincinnati (UC) have been developing a new class of ultrasensitive noble gas detectors that are based upon the ANL discovery that corn oil has a high affinity for heavy noble gas absorption at room temperature, but releases the noble gases with warming or by other low-energy-input means. Environmental applications for this new class of fluid-based detectors include ultrahigh sensitivity radioxenon detectors for Comprehensive Test Ban Treaty Surveillance, improved fission gas detectors for enhanced environmental surveillance in the vicinity of DOE, DOD, and NRC-licensed facilities, and improved integrating Rn detectors for earthquake prediction. The purpose of the present paper is to present the results of theoretical and experimental investigations into the solubility phenomena of heavy noble gases (Rn, Xe, and Kr) in triglyceride oils. It is the authors' intention that the findings presented herein may be used to guide future selection, development, and refinement of vegetable and other hydrocarbon oils to bring further enhancements to noble gas detection efficiencies

On the efficiency calibration of a drum waste assay system

CERN Document Server

Dinescu, L; Cazan, I L; Macrin, R; Caragheorgheopol, G; Rotarescu, G

2002-01-01

The efficiency calibration of a gamma spectroscopy waste assay system, constructed by IFIN-HH, was performed. The calibration technique was based on the assumption of a uniform distribution of the source activity in the drum and also a uniform sample matrix. A collimated detector (HPGe--20% relative efficiency) placed at 30 cm from the drum was used. The detection limit for sup 1 sup 3 sup 7 Cs and sup 6 sup 0 Co is approximately 45 Bq/kg for a sample of about 400 kg and a counting time of 10 min. A total measurement uncertainty of -70% to +40% was estimated.

Transverse mixing of ellipsoidal particles in a rotating drum

Directory of Open Access Journals (Sweden)

He Siyuan

2017-01-01

Full Text Available Rotating drums are widely used in industry for mixing, milling, coating and drying processes. In the past decades, mixing of granular materials in rotating drums has been extensively investigated, but most of the studies are based on spherical particles. Particle shape has an influence on the flow behaviour and thus mixing behaviour, though the shape effect has as-yet received limited study. In this work, discrete element method (DEM is employed to study the transverse mixing of ellipsoidal particles in a rotating drum. The effects of aspect ratio and rotating speed on mixing quality and mixing rate are investigated. The results show that mixing index increases exponentially with time for both spheres and ellipsoids. Particles with various aspect ratios are able to reach well-mixed states after sufficient revolutions in the rolling or cascading regime. Ellipsoids show higher mixing rate when rotational speed is set between 25 and 40 rpm. The relationship between mixing rate and aspect ratio of ellipsoids is established, demonstrating that, particles with aspect ratios of 0.5 and 2.0 achieve the highest mixing rates. Increasing rotating speed from 15 rpm to 40 rpm does not necessarily increase the mixing speed of spheres, while monotonous increase is observed for ellipsoids.

Plasma Glucose Levels for Red Drum Sciaenops Ocellatus in a Florida Estuarine Fisheries Reserve

Science.gov (United States)

Bourtis, Carla M.; Francis-Floyd, Ruth; Boggs, Ashley S P.; Reyier, Eric A.; Stolen, Eric D.; Yanong, Roy P.; Guillette, Louis J., Jr.

2015-01-01

Despite the significant value of the southeastern United States' red drum (Sciaenops ocellatus) fishery, there is a lack of clinical blood chemistry data. This was the first study to assess plasma glucose values as an indicator of stress response to evaluate variation and the effect of reproductive activity for wild adult red drum in Florida. Red drum (n=126) were collected from NASA's Kennedy Space Center waters during three reproductive periods in 2011. Samples were obtained from the branchial vessels of the gill arch. Plasma glucose levels were significantly different among reproductive periods, with the highest mean values recorded during the spawning period, September- October (38.23 mg / dL +/- 10.0). The glucose range was 17 - 69 mg / dL. Glucose values were lower during all three periods than previous values recorded for cultured or captive red drum studies. This may indicate that fish from this population were under less stress than other populations previously sampled.

Tribological Aspects of the Process of Winding the Steel Rope Around the Winch Drum

Directory of Open Access Journals (Sweden)

M. Matejić, , , ,

2014-03-01

Full Text Available Proper winding of the steel rope around the winch drum is great importance, mostly for: prolonging the service life of the rope, reduction of deformations of the body and the sides of the drum if the winding of the rope is multilayered, increasing of the safety factors, easier unwinding of the rope while lowering the load, even running of the drive unit, etc. The focus of this paper is on the analysis of the friction which occurs in the process of winding and unwinding the rope around the winch drum. Friction force is in its highest intensity when the rope passes from one layer to another, if the winding of the rope is multilayered. As the result of the research, certain mechanisms of winding of the rope from the aspects of the friction force were obtained, and the effects of the forces on the sides of the drum were analyzed.

Measurement of dose rate and estimation of beta activity in zircaloy hull drum

International Nuclear Information System (INIS)

Pandey, J.P.N.; Kumar, Pankaj; Shinde, A.M.; Purohit, R.G.; Sarkar, P.K.

2012-01-01

Fuel Reprocessing Plant is designed for the processing of spent fuel from reactor for the recovery of plutonium and uranium as PuO 2 and U 3 O 8 respectively. Zircaloy is used as cladding material of natural uranium fuel pins used in the reactors. In reprocessing plants chop and leach method is used to remove the zircaloy clad from the fuel matrix during Head End Treatment. Initially spent fuel bundles are chopped into pieces and collected in perforated baskets kept in dissolvers. All chopped pieces are dissolved in HNO 3 in the dissolvers followed by heating and boiling. Dissolved solutions are transferred to Filtrate Tank (FT) leaving behind un-dissolved zircoloy hull pieces in the dissolver baskets. Un-dissolved and almost dry hull pieces are transferred in hull drum from the dissolver baskets using the Hull Tilting Facility. Hull drums are made of stainless steel having 500 litre capacity and two third of its volume is filled with zircoloy pieces. Hull drums filled with hull pieces are loaded in Hull Removal Cask (HRC) and transported to SWMF (Solid Waste Management Facility) site for interim storage/disposal in tile holes. Hull pieces are high active solid wastes which contain significant amount of fission products. Radiation levels on hull drums are in the range of few hundreds of mGy/h which has high potential of external hazards if not handled properly. Therefore hull drums are handled remotely in specially designed lead shielded cask

Effect of noble gas ion pre-irradiation on deuterium retention in tungsten

NARCIS (Netherlands)

Cheng, L.; Zhao, Z. H.; De Temmerman, G.; Yuan, Y.; Morgan, T. W.; Guo, L. P.; Wang, B.; Zhang, Y.; Wang, B. Y.; Zhang, P.; Cao, X. Z.; Lu, G. H.

2016-01-01

Impurity seeding of noble gases is an effective way of decreasing the heat loads onto the divertor targets in fusion devices. To investigate the effect of noble gases on deuterium retention, tungsten targets have been implanted by different noble gas ions and subsequently exposed to deuterium

Atomic forces between noble gas atoms, alkali ions, and halogen ions for surface interactions

Science.gov (United States)

Wilson, J. W.; Outlaw, R. A.; Heinbockel, J. H.

1988-01-01

The components of the physical forces between noble gas atoms, alkali ions, and halogen ions are analyzed and a data base developed from analysis of the two-body potential data, the alkali-halide molecular data, and the noble gas crystal and salt crystal data. A satisfactory global fit to this molecular and crystal data is then reproduced by the model to within several percent. Surface potentials are evaluated for noble gas atoms on noble gas surfaces and salt crystal surfaces with surface tension neglected. Within this context, the noble gas surface potentials on noble gas and salt crystals are considered to be accurate to within several percent.

Kinematics and Path Following Control of an Articulated Drum Roller

Science.gov (United States)

BIAN, Yongming; YANG, Meng; FANG, Xiaojun; WANG, Xiahui

2017-07-01

Automatic navigation of an articulated drum roller, which is an articulated steering type vehicle widely used in the construction industry, is highly expected for operation cost reduction and improvement of work efficiency. In order to achieve the path following control, considering that its steering system is articulated steering and two frames are articulated by an active revolute joint, a kinematic model and an error dynamic state-space equation of an articulated drum roller are proposed. Besides, a state-feedback control law based on Lyapunov stability theory is also designed, which can be proved to achieve the purpose of control by the analysis of stability. What's more, to evaluate the performance of the proposed method, simulation under the MATLAB/Simulink and experiments using positioning algorithm and errors correction at the uneven construction site are performed, with initial displacement error (-1.5 m), heading error (-0.11 rad) and steering angle (-0.19 rad). Finally, simulation and experimental results show that the errors and steering angle can decrease gradually, and converge to zero with time. Meanwhile, the control input is not saturated. An articulated drum roller can lock into a desired path with the proposed method in uneven fields.

Estimation of possibility of brittle fracture in high pressure boiler drums

International Nuclear Information System (INIS)

Grin', E.A.

2005-01-01

Paper presents the results of analysis of the problem to ensure brittle strength of high pressure boiler drums made with application of the present-day methods of linear and nonlinear fracture mechanics. The charts of the temperature boundaries of brittle fracture and of the critical factors of stress intensity plotted depending on the actual properties of the material and on dimensions of flaws are presented for standard size drums made of 22K and 16GNM steels. In the paper there are some examples of the practical application of the given charts [ru

Steady-state ozone concentration in radiation induced noble gas-oxygen discharges

International Nuclear Information System (INIS)

Elsayed-Ali, H.E.; Miley, G.H.

1985-01-01

Measurements of steady-state ozone concentrations in continuous radiation induced noble gas-O 2 and noble gas-O 2 -SF 6 mixtures has been accomplished. The discharges were created through the bombardment of the gases with energetic particles from the boron-10 (n,α) lithium-7 nuclear reaction. Three noble gases were studied, He, Ne, and Ar at partial pressures of few hundred Torr. The dose rates studied were in the order of 10 15 eV.cm -3 .s -1 . The experimental apparatus and proceedure were previously described. The experimentally observed stead-state ozone concentrations in noble gas-O 2 discharges were about an order of magnitude lower than that observed for oxygen radiolysis at similar dose rates. These results were physically explained by an enhanced role of negative ionic reactions with ozone causing its destruction. In noble gas-O 2 -SF 6 mixtures, the steady-state ozone concentrations were found to be significantly higher (3-6 times) than that without the SF 6 addition. This observation was contrary to only a small increase observed after SF 6 addition to a few hundred Torr oxygen and is explained by an enhanced rate of electron dissociative attachment of ozone in noble gas-O 2 discharges

Filamentous fungi associated with natural infection of noble rot on withered grapes.

Science.gov (United States)

Lorenzini, M; Simonato, B; Favati, F; Bernardi, P; Sbarbati, A; Zapparoli, G

2018-05-02

The effects of noble rot infection of grapes on the characteristics of different types of wine, including Italian passito wine, are well known. Nevertheless, there is still little information on filamentous fungi associated with noble-rotten grapes. In this study, withered Garganega grapes for passito wine production, naturally infected by noble rot, were analyzed and compared to sound grapes. Skin morphology and fungal population on berry surfaces were analyzed. Scanning electron microscopy analysis revealed microcracks, germination conidia and branched hyphae on noble-rotten berries. Penicillium, Aureobasidium and Cladosporium were the most frequent genera present. Analysis of single berries displayed higher heterogeneity of epiphytic fungi in those infected by noble-rot than in sound berries. Penicillium adametzoides, Cladosporium cladospoirioides and Coniochaeta polymorpha were recovered. These, to the best of our knowledge, had never been previously isolated from withered grapes and, for C. polymorpha, from grapevine. This study provided novel data on noble rot mycobiota and suggests that fungi that co-habit with B. cinerea could have an important role on grape and wine quality. Copyright © 2018 Elsevier B.V. All rights reserved.

Corrosion of steel drums containing cemented ion-exchange resins as intermediate level nuclear waste

Science.gov (United States)

Duffó, G. S.; Farina, S. B.; Schulz, F. M.

2013-07-01

Exhausted ion-exchange resins used in nuclear reactors are immobilized by cementation before being stored. They are contained in steel drums that may undergo internal corrosion depending on the presence of certain contaminants. The objective of this work is to evaluate the corrosion susceptibility of steel drums in contact with cemented ion-exchange resins with different aggressive species. The corrosion potential and the corrosion rate of the steel, and the electrical resistivity of the matrix were monitored for 900 days. Results show that the cementation of ion-exchange resins seems not to pose special risks regarding the corrosion of the steel drums. The corrosion rate of the steel in contact with cemented ion-exchange resins in the absence of contaminants or in the presence of 2.3 wt.% sulphate content remains low (less than 0.1 μm/year) during the whole period of the study (900 days). The presence of chloride ions increases the corrosion rate of the steel at the beginning of the exposure but, after 1 year, the corrosion rate drops abruptly reaching a value close to 0.1 μm/year. This is probably due to the lack of water to sustain the corrosion process. When applying the results obtained in the present work to estimate the corrosion depth of the steel drums containing the cemented radioactive waste after a period of 300 years, it is found that in the most unfavourable case (high chloride contamination), the corrosion penetration will be considerably lower than the thickness of the wall of the steel drums. Cementation of ion-exchange resins does not seem to pose special risks regarding the corrosion of the steel drums that contained them; even in the case the matrix is highly contaminated with chloride ions.

CSER 00-006 Storage of Plutonium Residue Containers in 55 Gallon Drums at the PFP

Energy Technology Data Exchange (ETDEWEB)

DOBBIN, K.D.

2000-05-24

This criticality safety evaluation report (CSER) provides the required limit set and controls for safe transit and storage of these drums in the 234-5Z Building at the PFP. A mass limit of 200 g of plutonium or fissile equivalent per drum is acceptable

Reducing language to rhythm: Amazonian Bora drummed language exploits speech rhythm for long-distance communication

Science.gov (United States)

Seifart, Frank; Meyer, Julien; Grawunder, Sven; Dentel, Laure

2018-04-01

Many drum communication systems around the world transmit information by emulating tonal and rhythmic patterns of spoken languages in sequences of drumbeats. Their rhythmic characteristics, in particular, have not been systematically studied so far, although understanding them represents a rare occasion for providing an original insight into the basic units of speech rhythm as selected by natural speech practices directly based on beats. Here, we analyse a corpus of Bora drum communication from the northwest Amazon, which is nowadays endangered with extinction. We show that four rhythmic units are encoded in the length of pauses between beats. We argue that these units correspond to vowel-to-vowel intervals with different numbers of consonants and vowel lengths. By contrast, aligning beats with syllables, mora or only vowel length yields inconsistent results. Moreover, we also show that Bora drummed messages conventionally select rhythmically distinct markers to further distinguish words. The two phonological tones represented in drummed speech encode only few lexical contrasts. Rhythm thus appears to crucially contribute to the intelligibility of drummed Bora. Our study provides novel evidence for the role of rhythmic structures composed of vowel-to-vowel intervals in the complex puzzle concerning the redundancy and distinctiveness of acoustic features embedded in speech.

EOSN: A TOUGH2 module for noble gases

Energy Technology Data Exchange (ETDEWEB)

Shan, Chao; Pruess, Karsten

2003-03-07

We developed a new fluid property module for TOUGH2, called EOSN, to simulate transport of noble gases in the subsurface. Currently, users may select any of five different noble gases as well as CO2, two at a time. For the three gas components (air and two user-specified noble gases) in EOSN, the Henry's coefficients and the diffusivities in the gas phase are no longer assumed constants, but are temperature dependent. We used the Crovetto et al. (1982) model to estimate Henry's coefficients, and the Reid et al. (1987) correlations to calculate gas phase diffusivities. The new module requires users to provide names of the selected noble gases, which properties are provided internally. There are options for users to specify any (non-zero) molecular weights and half-lives for the gas components. We provide two examples to show applications of TOUGH2IEOSN. While temperature effects are relatively insignificant for one example problem where advection is dominant, they cause almost an order of magnitude difference for the other case where diffusion becomes a dominant process and temperature variations are relatively large. It appears that thermodynamic effects on gas diffusivities and Henry's coefficients can be important for low-permeability porous media and zones with large temperature variations.

EOSN: A TOUGH2 module for noble gases

International Nuclear Information System (INIS)

Shan, Chao; Pruess, Karsten

2003-01-01

We developed a new fluid property module for TOUGH2, called EOSN, to simulate transport of noble gases in the subsurface. Currently, users may select any of five different noble gases as well as CO2, two at a time. For the three gas components (air and two user-specified noble gases) in EOSN, the Henry's coefficients and the diffusivities in the gas phase are no longer assumed constants, but are temperature dependent. We used the Crovetto et al. (1982) model to estimate Henry's coefficients, and the Reid et al. (1987) correlations to calculate gas phase diffusivities. The new module requires users to provide names of the selected noble gases, which properties are provided internally. There are options for users to specify any (non-zero) molecular weights and half-lives for the gas components. We provide two examples to show applications of TOUGH2IEOSN. While temperature effects are relatively insignificant for one example problem where advection is dominant, they cause almost an order of magnitude difference for the other case where diffusion becomes a dominant process and temperature variations are relatively large. It appears that thermodynamic effects on gas diffusivities and Henry's coefficients can be important for low-permeability porous media and zones with large temperature variations

Experimental Method for Analyzing Friction Phenomenon Related to Drum Brake Squeal

Directory of Open Access Journals (Sweden)

J. GLIŠOVIĆ

2010-12-01

Full Text Available Automobile brakes have been intensively developed during past few decades, but the maximum motor’s power, that should amortized in vehicle brakes, has been significantly increased also. Most of the kinetic energy of the moving vehicles is transforming into heat through friction. But the small part of kinetic energy transforms into sound pressure and makes noise. Low frequency squeal of drum brakes is very intense and can lead to customers’ complain. The interaction between the brake system and the vehicle framework and suspension is often very substantial during occurrence of brake noise. Unfortunately, to solve this type of squeal problem is also difficult because of the large number of components involved. The other cause is attributed to self-excited vibration that is induced when the friction material has a negative slope in relation to the relative velocity. This paper illustrates an approach to experimental studies of drum brakes in road conditions in order to monitor changes in the coefficient of friction that can generate drum brake squeal at low frequencies.

Improvement of Algorithms for Pressure Maintenance Systems in Drum-Separators of RBMK-1000 Reactors

Energy Technology Data Exchange (ETDEWEB)

Aleksakov, A. N., E-mail: yankovskiy.k@nikiet.ru; Yankovskiy, K. I. [JSC “N. A. Dollezhal Research and Development Institute of Power Engineering (NIKIET),” (Russian Federation); Dunaev, V. I.; Kushbasov, A. N. [JSC “Diakont,” (Russian Federation)

2015-05-15

The main tasks and challenges for pressure regulation in the drum-separators of RBMK-1000 reactors are described. New approaches to constructing algorithms for pressure control in drum-separators by electro-hydraulic turbine control systems are discussed. Results are provided from tests of the operation of modernized pressure regulators during fast transients with reductions in reactor power.

High speed rotary drum

Energy Technology Data Exchange (ETDEWEB)

Sagara, H

1970-03-25

A high speed rotary drum is disclosed in which the rotor vessel is a double-wall structure comprising an inner wave-shaped pipe inserted coaxially within an outer straight pipe, the object being to provide a strengthened composite light-weight structure. Since force induced axial deformation of the straight pipe and radial deformation of the corrugated pipe are small, the composite effectively resists external forces and, if the waves of the inner pipe are given a sufficient amplitude, the thickness of both pipes may be reduced to lower the overall weight. Thus high angular velocities can be obtained to separate U/sup 235/ from gaseous UF/sub 6/.

Determination of the germanium detector efficiency for measurements of the radionuclide activity contained in a radioactive waste drum

International Nuclear Information System (INIS)

Rodenas, J.; Gallardo, S.; Ballester, S.; Hoyler, F.

2006-01-01

One of the features in the characterization of a drum containing radioactive wastes is to verify the activity of radionuclides contained in the drum. An H.P. Ge detector can be used for this measurement. However, it is necessary to perform an efficiency calibration for all geometries involved. In the framework of a joint project between the Departamento de Ingenieria Quimica y Nuclear (Universidad Politecnica de Valencia, Spain) and the Fachbereich Angewandte Naturwissenschaften und Technik (Fachhochschule Aachen, Abteilung Julich, Germany), different configurations for a drum containing radioactive sources have been implemented in the laboratory. A cylindrical drum of 850 mm height, a diameter equal to 560 mm and 3 mm of steel thickness has been used in the experimental measurements. The drum contains a clay ceramic matrix whose chemical composition is 55% SiO 2 , 40% of Al 2 O 3 and 5% of TiO 2 . Several vertical PVC tubes having a diameter of 30 mm are inserted in the drum at different distances from the central axis. In the experiment, a pack of point sources with 133 Ba, 60 Co and 137 Cs is introduced into each one of the tubes. A ring-shape distributed source is generated by rotating the drum around its axis during the measurement. The detector efficiency is determined experimentally for these configurations. On the other hand, a Monte Carlo model, using the M.C.N.P. code, has been developed to simulate the drum, the clay matrix and the PVC tubes. The effect of the drum spinning has been reproduced simulating a ring source with different diameters. The model also includes detailed detector geometry. Using this Monte Carlo model, the detector efficiency is calculated for each configuration implemented in the laboratory. Comparison of results from Monte Carlo simulation and experimental measurements should permit the validation of the M.C.N.P. model. Consequently it will be possible to obtain efficiency curves without experimental measurements. Therefore, these

Overview of the physical-chemical properties of the noble gases

International Nuclear Information System (INIS)

McKinley, C.

1973-01-01

This paper lists the concentrations of noble gases in the atmosphere and the relative abundance of the stable isotopes. Selected physical properties are tabulated; solubilities of noble gases in water and other liquids, and liquid-vapor equilibria data for binary systems containing a noble gas are presented. Adsorption data are tabulated for illustrative conventional adsorbents and are also presented by a Polanyi correlation. Clathration, biochemical effects, and chemical reactivity are highlighted. Analytical procedures are briefly described. Other relatively non-reactive gases present in the atmosphere in trace quantities are mentioned: methane, carbon tetrafluoride, and sulfur hexafluoride.

Steady-state ozone concentrations in radiation induced noble gas-oxygen discharges

International Nuclear Information System (INIS)

Elsayed-Ali, H.E.; Miley, G.H.

1985-01-01

Measurements of steady-state ozone concentrations in continuous radiation induced noble gas-O/sub 2/ and noble gas-o/sub 2/-SF/sub 6/ mixtures has been accomplished. The discharges were created through the bombardment of the gases with energetic particles from the boron-10 (n,α) lithium-7 nuclear reaction. Three noble gases were studied, He, Ne, and Ar at partial pressures of few hundred Torr. The dose rates studied were in the order of 10/sup 15/ eV . cm/sup -3/ . s/sup -1/. The experimental apparatus and procedure were previously described. The experimentally observed steady-state ozone concentrations in noble gas-O/sub 2/ discharges were about an order of magnitude lower than that observed for oxygen radiolysis at similar dose rates. These results were physically explained by an enhanced role of negative ionic reactions with ozone causing its destruction. In noble gas-O/sub 2/-SF/sub 6/ mixtures, the steady-state ozone concentrations were found to be significantly higher (3-6 times) than that without the SF/sub 6/ addition. This observation was contrary to only a small increase observed after SF/sub 6/ addition to a few hundred Torr oxygen and is explained by an enhanced rate of electron dissociative attachment of ozone in noble gas-O/sub 2/ discharges

Design of temperature detection device for drum of belt conveyor

Science.gov (United States)

Zhang, Li; He, Rongjun

2018-03-01

For difficult wiring and big measuring error existed in the traditional temperature detection method for drum of belt conveyor, a temperature detection device for drum of belt conveyor based on Radio Frequency(RF) communication is designed. In the device, detection terminal can collect temperature data through tire pressure sensor chip SP370 which integrates temperature detection and RF emission. The receiving terminal which is composed of RF receiver chip and microcontroller receives the temperature data and sends it to Controller Area Network(CAN) bus. The test results show that the device meets requirements of field application with measuring error ±3.73 ° and single button battery can provide continuous current for the detection terminal over 1.5 years.

Engineering noble metal nanomaterials for environmental applications

Science.gov (United States)

Li, Jingguo; Zhao, Tingting; Chen, Tiankai; Liu, Yanbiao; Ong, Choon Nam; Xie, Jianping

2015-04-01

Besides being valuable assets in our daily lives, noble metals (namely, gold, silver, and platinum) also feature many intriguing physical and chemical properties when their sizes are reduced to the nano- or even subnano-scale; such assets may significantly increase the values of the noble metals as functional materials for tackling important societal issues related to human health and the environment. Among which, designing/engineering of noble metal nanomaterials (NMNs) to address challenging issues in the environment has attracted recent interest in the community. In general, the use of NMNs for environmental applications is highly dependent on the physical and chemical properties of NMNs. Such properties can be readily controlled by tailoring the attributes of NMNs, including their size, shape, composition, and surface. In this feature article, we discuss recent progress in the rational design and engineering of NMNs with particular focus on their applications in the field of environmental sensing and catalysis. The development of functional NMNs for environmental applications is highly interdisciplinary, which requires concerted efforts from the communities of materials science, chemistry, engineering, and environmental science.

Engineering noble metal nanomaterials for environmental applications.

Science.gov (United States)

Li, Jingguo; Zhao, Tingting; Chen, Tiankai; Liu, Yanbiao; Ong, Choon Nam; Xie, Jianping

2015-05-07

Besides being valuable assets in our daily lives, noble metals (namely, gold, silver, and platinum) also feature many intriguing physical and chemical properties when their sizes are reduced to the nano- or even subnano-scale; such assets may significantly increase the values of the noble metals as functional materials for tackling important societal issues related to human health and the environment. Among which, designing/engineering of noble metal nanomaterials (NMNs) to address challenging issues in the environment has attracted recent interest in the community. In general, the use of NMNs for environmental applications is highly dependent on the physical and chemical properties of NMNs. Such properties can be readily controlled by tailoring the attributes of NMNs, including their size, shape, composition, and surface. In this feature article, we discuss recent progress in the rational design and engineering of NMNs with particular focus on their applications in the field of environmental sensing and catalysis. The development of functional NMNs for environmental applications is highly interdisciplinary, which requires concerted efforts from the communities of materials science, chemistry, engineering, and environmental science.

Results of the gamma-neutron mapper performance test on 55-gallon drums at the RWMC

International Nuclear Information System (INIS)

Gehrke, R.J.; Lawrence, R.S.; Roybal, L.G.; Svoboda, J.M.; Harker, D.J.; Thompson, D.N.; Carpenter, M.V.; Josten, N.E.

1995-07-01

The primary purpose of the gamma-neutron mapper (G at sign) is to provide accurate and quantitative spatial information of the gamma-ray and neutron radiation fields as a function of position about the excavation of a radioactive waste site. The GNM is designed to operate remotely and can be delivered to any point on an excavation by the robotic gantry crane developed by the dig-face project at the Idaho National Engineering Laboratory (INEL). It can also be easily adapted to other delivery systems. The GNM can be deployed over a waste site at a predetermined scan rate and has sufficient accuracy to identify and quantify radioactive contaminants of importance. The results reported herein are from a performance test conducted at the Transuranic Storage Area, Building 628, of the Radioactive Waste Management Complex located at the INEL. This building is an active interim-storage area for 55-gal drums of transuranic waste from the Department of Energy's Rocky Flats Plant. The performance test consisted of scanning a stack of drums five high by five wide. Prior to the test, radiation fields were measured by a health physicist at the center of the drums and ranged from 0.5 mR/h to 35 mR/h. Scans of the drums using the GNM were taken at standoff distances from the vertical drum stack of 15 cm, 30 cm, 45 cm, and 90 cm. Data were acquired at scan speeds of 7.5 cm/s and 15 cm/s. The results of these scans and a comparison of these results with the manifests of these drums are compared and discussed

First-principles study of noble gas stability in ThO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Shao, Kuan [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Han, Han, E-mail: hanhanfudan@gmail.com [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China); Zhang, Wei [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China); Key Laboratory of Interfacial Physics and Technology, Chinese Academy of Sciences, Shanghai 201800 (China); Wang, Hui [School of Physics and Engineering, Henan University of Science and Technology, Luoyang 471003 (China); Wang, Chang-Ying; Guo, Yong-Liang [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China); Ren, Cui-Lan [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China); Key Laboratory of Interfacial Physics and Technology, Chinese Academy of Sciences, Shanghai 201800 (China); Huai, Ping, E-mail: huaiping@sinap.ac.cn [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China)

2017-07-15

The stability of noble gases (He, Ne, Ar, Kr and Xe) in thorium dioxide is studied by means of density functional theory. The computations are performed considering insertion sites of ThO{sub 2}, including the interstitial sites, the thorium vacancies, the oxygen-thorium di-vacancy and three types of Schottky defects. Our results show that there is an approximately linear relation between the energies and the atomic radii. As the size of the noble gas atom increases, the noble gas atoms energetically prefer to incorporate into large vacancy defects rather than into interstitial positions. Moreover, the binding energy of Kr or Xe interstitial in a Schottky defect is larger than the formation energy of a Schottky defect, suggesting the Schottky defects are thermodynamically favorable in the presence of these noble gas atoms. The charged defects are also considered for noble gas atoms trapped in Th and O vacancies.

Recovery of noble metals from fission products

International Nuclear Information System (INIS)

Jenson, G.A.; Platt, A.M.; Mellinger, G.B.; Bjorklund, W.J.

1982-11-01

Scoping studies were started in 1979 to develop a cost-effective, waste-management-compatible process to extract noble metals from fission products. The process, involving the reaction with glassmelting chemicals, a metal oxide (PbO), and a reducing agent (charcoal), was demonstrated for recovering noble metals from simulated high-level waste oxides. The process has now been demonstrated on a laboratory scale (100 g) using irradiated fuels. Recoveries in the recovered lead averaged 80% for Pd, 60% for Rh, and 14% Ru. The resulting glass product was homogeneous in appearance, and the chemical durability was comparable to other waste oxides

Source Test Report for the 205 Delayed Coking Unit Drum 205-1201 and Drum 205-1202 Depressurization Vents (Marathon Petroleum Company LLC)

Science.gov (United States)

The 2010 Source Test was performed during the atmospheric depressurization step of the delayed coking process prior to the removal of petroleum coke from the coke drum. The 205 DCU was operated under a variety of conditions during the 2010 Source Test.

High Voltage in Noble Liquids for High Energy Physics

Energy Technology Data Exchange (ETDEWEB)

Rebel, B. [Fermilab; Bernard, E. [Yale U.; Faham, C. H. [LBL, Berkeley; Ito, T. M. [Los Alamos; Lundberg, B. [Maryland U.; Messina, M. [Columbia U.; Monrabal, F. [Valencia U., IFIC; Pereverzev, S. P. [LLNL, Livermore; Resnati, F. [Zurich, ETH; Rowson, P. C. [SLAC; Soderberg, M. [Fermilab; Strauss, T. [Bern U.; Tomas, A. [Imperial Coll., London; Va' vra, J. [SLAC; Wang, H. [UCLA

2014-08-22

A workshop was held at Fermilab November 8-9, 2013 to discuss the challenges of using high voltage in noble liquids. The participants spanned the fields of neutrino, dark matter, and electric dipole moment physics. All presentations at the workshop were made in plenary sessions. This document summarizes the experiences and lessons learned from experiments in these fields at developing high voltage systems in noble liquids.

Metal-organic frameworks for adsorption and separation of noble gases

Energy Technology Data Exchange (ETDEWEB)

Allendorf, Mark D.; Greathouse, Jeffery A.; Staiger, Chad

2017-05-30

A method including exposing a gas mixture comprising a noble gas to a metal organic framework (MOF), including an organic electron donor and an adsorbent bed operable to adsorb a noble gas from a mixture of gases, the adsorbent bed including a metal organic framework (MOF) including an organic electron donor.

Criticality safety study of Pu contaminated carbon waste stored in 100 L steel drums

International Nuclear Information System (INIS)

Anno, J.; Simonneau, M.

1995-01-01

The notion of the minimum critical areal density (D minca ) used to ensure the Criticality-Safety of poor solid waste is recalled with its deficiencies. D minca is assumed constant, independent of the fissile material concentration. This assumption is only true for unreflected mediums. Corrective factors are established. Furthermore, the usual norm of the Pu-H 2 O, which is 0.20 g/cm 2 , (concrete reflected) is greater than that for other mediums, such as Pu contaminated graphite waste (Pu-C), which is 0.036 g/cm 2 . D minca calculated on infinite slabs is confirmed by calculations on infinite planar multilayers arrays of 100 l cubical waste drums. Moreover, d minca increases linearly with the steel thickness of the drums' walls and goes up to 0.17 g/cm 2 for 0.105 cm of steel. The safety analysis on a real storage case takes into account the limited amount of Pu (100 g) and C (100 kg), the minimum thickness of 0.07 cm of drums' steel, their geometrical arrangement, the heterogeneity and size of contamination and the occurrence of neutronic poison (N and Cl) in the waste. Because of these parameters, the Keff are very less than 0.95 and the taken norm of 0.1 g/cm 2 for the Pu-C waste is fulfilled. Finally, it is demonstrated that the mixing of Pu-C waste drums and Pu-H 2 O wastes drums is allowed. (authors). 14 refs., 5 figs., 6 tabs

Ab initio theory of noble gas atoms in bcc transition metals.

Science.gov (United States)

Jiang, Chao; Zhang, Yongfeng; Gao, Yipeng; Gan, Jian

2018-06-18

Systematic ab initio calculations based on density functional theory have been performed to gain fundamental understanding of the interactions between noble gas atoms (He, Ne, Ar and Kr) and bcc transition metals in groups 5B (V, Nb and Ta), 6B (Cr, Mo and W) and 8B (Fe). Our charge density analysis indicates that the strong polarization of nearest-neighbor metal atoms by noble gas interstitials is the electronic origin of their high formation energies. Such polarization becomes more significant with an increasing gas atom size and interstitial charge density in the host bcc metal, which explains the similar trend followed by the unrelaxed formation energies of noble gas interstitials. Upon allowing for local relaxation, nearby metal atoms move farther away from gas interstitials in order to decrease polarization, albeit at the expense of increasing the elastic strain energy. Such atomic relaxation is found to play an important role in governing both the energetics and site preference of noble gas atoms in bcc metals. Our most notable finding is that the fully relaxed formation energies of noble gas interstitials are strongly correlated with the elastic shear modulus of the bcc metal, and the physical origin of this unexpected correlation has been elucidated by our theoretical analysis based on the effective-medium theory. The kinetic behavior of noble gas atoms and their interaction with pre-existing vacancies in bcc transition metals have also been discussed in this work.

40 CFR 264.316 - Disposal of small containers of hazardous waste in overpacked drums (lab packs).

Science.gov (United States)

2010-07-01

... HAZARDOUS WASTE TREATMENT, STORAGE, AND DISPOSAL FACILITIES Landfills § 264.316 Disposal of small containers of hazardous waste in overpacked drums (lab packs). Small containers of hazardous waste in overpacked... hazardous waste in overpacked drums (lab packs). 264.316 Section 264.316 Protection of Environment...

40 CFR 265.316 - Disposal of small containers of hazardous waste in overpacked drums (lab packs).

Science.gov (United States)

2010-07-01

... OPERATORS OF HAZARDOUS WASTE TREATMENT, STORAGE, AND DISPOSAL FACILITIES Landfills § 265.316 Disposal of small containers of hazardous waste in overpacked drums (lab packs). Small containers of hazardous waste... hazardous waste in overpacked drums (lab packs). 265.316 Section 265.316 Protection of Environment...

Corrosion susceptibility of steel drums containing cemented intermediate level nuclear wastes

Science.gov (United States)

Duffó, Gustavo S.; Farina, Silvia B.; Schulz, Fátima M.; Marotta, Francesca

2010-10-01

Cementation processes are used as immobilization techniques for low or intermediate level radioactive waste for economical and safety reasons and for being a simple operation. In particular, ion-exchange resins commonly used for purification of radioactive liquid waste from nuclear reactors are immobilized before being stored to improve the leach resistance of the waste matrix and to maintain mechanical stability. Combustible solid radioactive waste can be incinerated and the resulting ashes can also be immobilized before storage. The immobilized resins and ashes are then contained in steel drums that may undergo corrosion depending on the presence of certain contaminants. The work described in this paper was aimed at evaluating the corrosion susceptibility of steel drums in contact with cemented ion-exchange resins and incineration ashes containing different concentrations of aggressive species (mostly chloride and sulphate ions). A special type of specimen was designed to simulate the cemented waste in the drum. The evolution of the corrosion potential and the corrosion current density of the steel, as well as the electrical resistivity of the matrix were monitored over a time period of 1 year. The results show the deleterious effect of chloride on the expected lifespan of the waste containers.

Corrosion susceptibility of steel drums containing cemented intermediate level nuclear wastes

International Nuclear Information System (INIS)

Duffo, Gustavo S.; Farina, Silvia B.; Schulz, Fatima M.; Marotta, Francesca

2010-01-01

Cementation processes are used as immobilization techniques for low or intermediate level radioactive waste for economical and safety reasons and for being a simple operation. In particular, ion-exchange resins commonly used for purification of radioactive liquid waste from nuclear reactors are immobilized before being stored to improve the leach resistance of the waste matrix and to maintain mechanical stability. Combustible solid radioactive waste can be incinerated and the resulting ashes can also be immobilized before storage. The immobilized resins and ashes are then contained in steel drums that may undergo corrosion depending on the presence of certain contaminants. The work described in this paper was aimed at evaluating the corrosion susceptibility of steel drums in contact with cemented ion-exchange resins and incineration ashes containing different concentrations of aggressive species (mostly chloride and sulphate ions). A special type of specimen was designed to simulate the cemented waste in the drum. The evolution of the corrosion potential and the corrosion current density of the steel, as well as the electrical resistivity of the matrix were monitored over a time period of 1 year. The results show the deleterious effect of chloride on the expected lifespan of the waste containers.

Development of simulation code for FBR spent fuel dissolution with rotary drum type continuous dissolver

International Nuclear Information System (INIS)

Sano, Yuichi; Katsurai, Kiyomichi; Washiya, Tadahiro; Koizumi, Tsutomu; Matsumoto, Satoshi

2011-01-01

Japan Atomic Energy Agency (JAEA) has been studying rotary drum type continuous dissolver for FBR spent fuel dissolution. For estimating the fuel dissolution behavior under several operational conditions in this dissolver, we have been developing the simulation code, PLUM, which mainly consists of 3 modules for calculating chemical reaction, mass transfer and thermal balance in the rotary drum type continuous dissolver. Under the various conditions where dissolution experiments were carried out with the batch-wise dissolver for FBR spent fuel and with the rotary drum type continuous dissolver for UO 2 fuel, it was confirmed that the fuel dissolution behaviors calculated by the PLUM code showed good agreement with the experimental ones. Based on this result, the condition for obtaining the dissolver solution with high HM (heavy metal : U and Pu) concentration (∼500g/L), which is required for the next step, i.e. crystallization process, was also analyzed by this code and appropriate operational conditions with the rotary drum type continuous dissolver, such as feedrate, concentration and temperature of nitric acid, could be clarified. (author)

First ECR-Ionized Noble Gas Radioisotopes at ISOLDE

CERN Document Server

Wenander, F; Gaubert, G; Jardin, P; Lettry, Jacques

2004-01-01

The production of light noble gas radioisotopes with high ionization potentials has been hampered by modest ionization efficiencies for standard plasma ion-sources. However, the decay losses are minimal as the lingering time of light noble gases within plasma ion-sources is negligible when compared to its diffusion out of the target material. Previous singly charged ECRIS have shown a higher efficiency but also a lingering time of the order of 1 s and a total weight that prevents remote handling by the ISOLDE robot. The compact MINIMONO efficiently addressed the lingering time and weight issues. In addition, the MINIMONO maintained the high off-line ionization efficiency for light noble gases. This paper describes a standard ISOLDE target unit equipped with a MINIMONO ion-source and the first tests. The ion-source has been tested off-line and equipped with a CaO target for on-line tests. Valuable information was gained about high current (100-500 muA) transport through the ISOLDE mass separators designed for ...

Recent Experimental Advances to Determine (noble) Gases in Waters

Science.gov (United States)

Kipfer, R.; Brennwald, M. S.; Huxol, S.; Mächler, L.; Maden, C.; Vogel, N.; Tomonaga, Y.

2013-12-01

In aquatic systems noble gases, radon, and bio-geochemically conservative transient trace gases (SF6, CFCs) are frequently applied to determine water residence times and to reconstruct past environmental and climatic conditions. Recent experimental breakthroughs now enable ● to apply the well-established concepts of terrestrial noble gas geochemistry in waters to the minute water amounts stored in sediment pore space and in fluid inclusions (A), ● to determine gas exchange processes on the bio-geochemical relevant time scales of minutes - hours (B), and ● to separate diffusive and advective gas transport in soil air (C). A. Noble-gas analysis in water samples (transport in the pore space and identifying the origin of bio- and geogenic fluids in (un) consolidated sediments [1]. Advanced techniques that combine crushing and sieving speleothem samples in ultra-high-vacuum to a specific grain size allow to separate air and water-bearing fluid inclusions and thus enables noble-gas-based reconstruction of environmental conditions from water masses as small as 1mg [2]. B. The coupling of noble gas analysis with approaches of gas chromatography permits combined analysis of noble gases and other gases species (e.g., SF6, CFCs, O2, N2) from a single water sample. The new method substantially improves ground water dating by SF6 and CFCs as excess air is quantified from the same sample and hence can adequately be corrected for [3]. Portable membrane-inlet mass spectrometers enable the quasi-continuous and real-time analysis of noble gases and other dissolved gases directly in the field, allowing, for instance, quantification of O2 turnover rates on small time scales [4]. C. New technical developments perfect 222Rn analysis in water by the synchronous the determination of the short-lived 220Rn. The combined 220,222Rn analysis sheds light on the emanation behaviour of radon by identifying soil water content to be the crucial control of 220Rn occurrence in the environment

Effective Giromagnetic Ratios in Artifical Nuclear Magnetization Pumping of the Noble Gases Mix

Directory of Open Access Journals (Sweden)

Popov E.N.

2015-01-01

Full Text Available Dynamic of the nuclear magnetization of the two noble gases mix was studied in this research. Nuclear magnetization pumped along the induction of external magnetic field. Vector of nuclear magnetization is given a tilt by the week rotational magnetic field, which makes NMR for noble gases. Interaction between the nuclear magnetic moments of the different noble gases adducted to shifts at the frequency of nuclear moments precession in external magnetic field. Effective gyromagnetic ratios of the nuclear of noble gases is defined and it different from the tabulated value. There is theoretical calculation of effective gyromagnetic ratios in this research.

Noble Estate Self-Government in Russia: Between the State and Civil Society

Directory of Open Access Journals (Sweden)

Alexander Yu. Morozov

2016-10-01

Full Text Available This article is devoted to assessing the role of noble self-governance in the history of Russia. According to Boris Mironov, before the Great Reforms of the 1860s, each noble assembly was a part of civil society. This point of view has aroused objections and debate among Russian historians. Morozov analyzed the historiographical aspect of the problem and demonstrated the impact of the socio-political context of their scientific work on Russian historians. In his opinion, from a purely legal point of view, there is reason to conclude that the autonomy of noble assemblies increased in the first half of the 19th century. However, the question of the extent to which these opportunities were realized in practice has been poorly studied. In the literature, there are examples of effective methods of influencing the government at the noble assemblies despite legal restrictions, as well as examples of noble assemblies that did not restrain the arbitrariness of the crown authority, did not protect their members from its abuse, and did not serve as the expression of public opinion. Mironov’s attempt to place in doubt the fact of the widespread presence of absenteeism seems unconvincing to Morozov. However, he agrees with Mironov that after 1861, the nobility really became a part of civil society, because the activity of noble organizations increased substantially in many different directions, including the political. For almost half a century of its history, the noble corporate organization evolved from a traditional institution into a civil one, which retained many features of traditional organization.

Feeling the beat where it counts: fostering multi-limb rhythm skills with the haptic drum kit

NARCIS (Netherlands)

Holland, S.; Bouwer, A.J.; Dalgleish, M.; Hurtig, T.M.

2010-01-01

This paper introduces a tool known as the Haptic Drum Kit, which employs four computer-controlled vibrotactile devices, one attached to each wrist and ankle. In the applications discussed here, haptic pulses are used to guide the playing, on a drum kit, of rhythmic patterns that require multi-limb

CT examination of radwaste drums

International Nuclear Information System (INIS)

Duwe, R.; Jansen, P.

1988-01-01

In order to garantee safe operation of the waste disposal site it is inevitable for the operator to know the radioactive inventory as well as the physical and chemical properties of the conditioned waste. The declarations of the waste producers describing the type, amount and conditioning of the wastes are taken as a basis for specifications of waste forms. The aim of the work till now was to install simple measuring desk for emission computed tomography in order to count γ-activity levels in drums, and to detect density distributions by transmission computed tomography. (orig.) [de

Noble Gas Concept Of Operation

Energy Technology Data Exchange (ETDEWEB)

Carrigan, C. R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2014-01-20

The intent of this document is to provide the reader with an understanding of a general approach to performing the noble gas component of an On Site Inspection or OSI. The authors of this document recognize that owing to the wide range of scenarios that are possible for carrying out an underground nuclear explosion, the diverse sets of information that might be available to the inspection team initially and the potential range of political and physical constraints imposed during the inspection, a satisfactory prescriptive approach to carrying out the noble gas component of an OSI is unlikely. Rather, the authors intend only to aid the reader in understanding what a reasonable course of actions or responses may be as performed by an inspection team (IT) during a general OSI. If this document helps to inform the intuition of the reader about addressing the challenges resulting from the inevitable deviations from this general scenario, it will have achieved its intent.

A novel method for fission product noble gas sampling

International Nuclear Information System (INIS)

Jain, S.K.; Prakash, Vivek; Singh, G.K.; Vinay, Kr.; Awsthi, A.; Bihari, K.; Joyson, R.; Manu, K.; Gupta, Ashok

2008-01-01

Noble gases occur to some extent in the Earth's atmosphere, but the concentrations of all but argon are exceedingly low. Argon is plentiful, constituting almost 1 % of the air. Fission Product Noble Gases (FPNG) are produced by nuclear fission and large parts of FPNG is produced in Nuclear reactions. FPNG are b-j emitters and contributing significantly in public dose. During normal operation of reactor release of FPNG is negligible but its release increases in case of fuel failure. Xenon, a member of FPNG family helps in identification of fuel failure and its extent in PHWRs. Due to above reasons it becomes necessary to assess the FPNG release during operation of NPPs. Presently used methodology of assessment of FPNG, at almost all power stations is Computer based gamma ray spectrometry. This provides fission product Noble gases nuclide identification through peak search of spectra. The air sample for the same is collected by grab sampling method, which has inherent disadvantages. An alternate method was developed at Rajasthan Atomic Power Station (RAPS) - 3 and 4 for assessment of FPNG, which uses adsorption phenomena for collection of air samples. This report presents details of sampling method for FPNG and noble gases in different systems of Nuclear Power Plant. (author)

The Effect of Aqueous Alteration on Primordial Noble Gases in CM Chondrites

Science.gov (United States)

Weimer, D.; Busemann, H.; Alexander, C. M. O'D.; Maden, C.

2017-07-01

We have analyzed 32 CM chondrites for their noble gas contents and isotopic compositions and calculated CRE ages. Correlated effects of parent body aqueous alteration with primordial noble gas contents were detected.

Noble Gas Detectors

CERN Document Server

Aprile, Elena; Bolozdynya, Alexander I; Doke, Tadayoshi

2006-01-01

This book discusses the physical properties of noble fluids, operational principles of detectors based on these media, and the best technical solutions to the design of these detectors. Essential attention is given to detector technology: purification methods and monitoring of purity, information readout methods, electronics, detection of hard ultra-violet light emission, selection of materials, cryogenics etc.The book is mostly addressed to physicists and graduate students involved in the preparation of fundamental next generation experiments, nuclear engineers developing instrumentation

The behavior and effects of the noble metals in the DWPF melter system

International Nuclear Information System (INIS)

Hutson, N.D.; Smith, M.E.

1992-01-01

Fission-product noble metals have caused severe operating problems in numerous worldwide waste vitrification facilities. These dense, highly conductive noble metals have tended to accumulate on the floor of joule-heated glass melters causing electrical distortions which have, in some occurrences, rendered the melter inoperable. A pilot scale vitrification research facility at the U.S. Department of Energy's Savannah River Laboratory has been operated for more than a year with simulated feed streams containing noble metals. In this paper the behavior of these noble metals in the melter system and final glass product and their effects on the scaled DWPF-type melter are discussed

Steam drum level dynamics in a multiple loop natural circulation system of a pressure-tube type boiling water reactor

International Nuclear Information System (INIS)

Jain, Vikas; Kulkarni, P.P.; Nayak, A.K.; Vijayan, P.K.; Saha, D.; Sinha, R.K.

2011-01-01

Highlights: → We have highlighted the problem of drum level dynamics in a multiple loop type NC system using RELAP5 code. → The need of interconnections in steam and liquid spaces close to drum is established. → The steam space interconnections equalize pressure and liquid space interconnections equalize level. → With this scheme, the system can withstand anomalous conditions. → However, the controller is found to be inevitable for inventory balance. - Abstract: Advanced Heavy Water Reactor (AHWR) is a pressure tube type boiling water reactor employing natural circulation as the mode of heat removal under all the operating conditions. Main heat transport system (MHTS) of AHWR is essentially a multi-loop natural circulation system with all the loops connected to each other. Each loop of MHTS has a steam drum that provides for gravity based steam-water separation. Steam drum level is a very critical parameter especially in multi-loop natural circulation systems as large departures from the set point may lead to ineffective separation of steam-water or may affect the driving head. However, such a system is susceptible to steam drum level anomalies under postulated asymmetrical operating conditions among the different quadrants of the core like feedwater flow distribution anomaly among the steam drums or power anomaly among the core quadrants. Analyses were carried out to probe such scenarios and unravel the underlying dynamics of steam drum level using system code RELAP5/Mod3.2. In addition, a scheme to obviate such problem in a passive manner without dependence on level controller was examined. It was concluded that steam drums need to be connected in the liquid as well as steam space to make the system tolerant to asymmetrical operating conditions.

Effective collision frequency of electrons in noble gases

International Nuclear Information System (INIS)

Baille, P.; Chang, J.-S.; Claude, A.; Yau, A.W.; Hobson, R.M.; Ogram, G.L.

1981-01-01

The electron-neutral collision frequency in the noble gases has been calculated using recent numerical results for momentum transfer cross sections by assuming a Maxwellian distribution of electron velocities. In all these gases, except for argon, good agreement is obtained with most previously published experimental and theoretical data. Mean free path, mobilities and diffusion coefficients are also calculated from the resulting effective collision frequencies. The empirical formulae are presented for an electron temperature dependence of the electron-neutral collision frequency for all noble gases up to Tsub(e) < approximately 25.000 K. (author)

A prototype of radioactive waste drum monitor by non-destructive assays using gamma spectrometry

International Nuclear Information System (INIS)

Thanh, Tran Thien; Trang, Hoang Thi Kieu; Chuong, Huynh Dinh; Nguyen, Vo Hoang; Tran, Le Bao; Tam, Hoang Duc; Tao, Chau Van

2016-01-01

In this work, segmented gamma scanning and the gamma emission tomography were used to locate unknown sources in a radioactive waste drum. The simulated detector response function and full energy peak efficiency are compared to corresponding experimental data and show about 5.3% difference for an energy ranging from 81 keV to 1332.5 keV for point sources. Computation of the corresponding activity is in good agreement with the true values. - Highlights: • Segmented gamma scanning and gamma emission tomography are used to locate point source in waste drums. • The PENELOPE software is used to compute the detection efficiency of the localized point source in the waste drum. • The activity of "1"3"7Cs and "6"0Co point source could be determined with an accuracy better than 10% for air and sand matrices.

Handling 78,000 drums of mixed-waste sludge

International Nuclear Information System (INIS)

Berry, J.B.; Harrington, E.S.; Mattus, A.J.

1991-01-01

The Oak Ridge Gaseous Diffusion Plant (now known as the Oak Ridge K-25 Site) closed two mixed-waste surface impoundments by removing the sludge and contaminated pond-bottom clay and attempting to process it into durable, nonleachable, concrete monoliths. Interim, controlled, above-ground storage included delisting the stabilized sludge from hazardous to nonhazardous and disposing of the delisted monoliths as Class 1 radioactive waste. Because of schedule constraints and process design and control deficiencies, ∼46,000 drums of material in various stages of solidification and ∼32,000 barrels of unprocessed sludge are stored. The abandoned treatment facility still contains ∼16,000 gal of raw sludge. Such storage of mixed waste does not comply with the Resource Conservation and Recovery Act (RCRA) guidelines. This paper describes actions that are under way to bring the storage of ∼78,000 drums of mixed waste into compliance with RCRA. Remediation of this problem by treatment to meet regulatory requirements is the focus of the discussion. 3 refs., 2 figs., 4 tabs

Behavior of shut-down dose rate of recirculation piping of BWR under noble metal application

International Nuclear Information System (INIS)

Fuse, Motomasa; Nagase, Makoto; Aizawa, Motohiro; Wada, Yoichi; Ishida, Kazushige; Hosokawa, Hideyuki; Hettiarachchi, Samson; Weber, Christoph

2014-01-01

The cause of shut-down dose rate change of the recirculation piping observed in KKM (Kern Kraftwerk Mühleberg) after application of noble metal injection method is analyzed. The plant experienced the sharp decrease of piping dose rate in the cycle just after the application of noble metal(classic NobleChem TM ) and re-buildup of radioactivity in the subsequent several cycles. After the application of online noble metal injection (online NobleChem TM ), gradual decrease of dose rate has been observed. The presence of a certain amount of noble metal on the iron rich oxide film promotes the dissolution of the oxide under hydrogen addition, resulting in a decrease of deposited noble metal on the oxide film surface as well as of radioactive species in the film. Under the condition of lower amount of noble metal on the surface oxides, the oxidant species, especially hydrogen peroxide, slightly increases facilitating the re-growth of iron rich oxides along with re-buildup of radioactivity. After the application of online noble metal injection during each cycle, gradual dissolution of iron rich oxides and gradual decrease of radioactivity in the oxides proceed to decrease the piping dose rate. In the radioactivity decreasing phase, the presence of zinc is considered to assist the suppression of radioactivity buildup in the oxide film. From the analysis, treating piping surface with platinum after chemical decontamination process is expected to work well for suppression of the piping dose rate. (author)

Targets Involved in Cardioprotection by the Non-Anesthetic Noble Gas Helium

NARCIS (Netherlands)

Weber, Nina C.; Smit, Kirsten F.; Hollmann, Markus W.; Preckel, Benedikt

2015-01-01

Research data from the past decade indicate that noble gases like xenon and helium exert profound cardioprotection when applied before, during or after organ ischemia. Of all noble gases, especially helium, has gained interest in the past years because it does not have an anesthetic "side effect"

Structural and plasmonic properties of noble metal doped ZnO nanomaterials

Science.gov (United States)

Pathak, Trilok K.; Swart, H. C.; Kroon, R. E.

2018-04-01

Noble metal doped ZnO has been synthesized by the combustion method and the effect of different metals (Ag, Au, Pd) on the structural, morphological, optical, photoluminescence and localized surface plasmon resonance (LSPR) properties has been investigated. X-ray diffraction analysis revealed that the ZnO had a hexagonal wurtzite structure and the crystallite sizes were affected by the doping. The formation of noble metal nanoparticles (NPs) was investigated using transmission electron microscopy and diffuse reflectance spectra. The LSPR of the metallic NPs was predicted using Mie theory calculations. The absorption spectra were calculated using the Kubelka-Munk function and the optical bandgap varied from 3.06 to 3.18 eV for the different doping materials. The experimental results suggest that the origin of enhanced emission was due to direct interaction between the laser photons and the noble material NPs which in turn leads to photoemission transfer of electrons from the noble metals NPs to the conduction band of ZnO.

Preliminary minimum detectable limit measurements in 208-L drums for selected actinide isotopes in mock-waste matrices

International Nuclear Information System (INIS)

Camp, D.C.; Wang, Tzu-Fang; Martz, H.E.

1992-01-01

Preliminary minimum detectable levels (MDLS) of selected actinide isotopes have been determined in full-scale, 55-gallon drums filled with a range of mock-waste materials from combustibles (0.14 g/CM 3 ) to sand (1.7 g/CM 3 ). Measurements were recorded from 100 to 10,000 seconds with selected actinide sources located in these drums at an edge position, on the center axis of a drum and midway between these two positions. Measurements were also made with a 166 Ho source to evaluate the attenuation of these mock-matrix materials as a function of energy. By knowing where the source activity is located within a drum, our preliminary results show that a simply collimated 90% HPGE detector can differentiate between TRU (>100 nCi/g) and LLW amounts of 239 Pu in only 100s of measurement time and with sufficient accuracy in both low and medium density, low Z materials. Other actinides measured so far include 235 U, 241 Am, and 244 Cm. These measurements begin to establish the probable MDLs achievable in the nondestructive assays of real waste drums when using active and passive CT. How future measurements may differ from these preliminary measurements is also discussed

The Inert and the Noble

Indian Academy of Sciences (India)

Home; Journals; Resonance – Journal of Science Education; Volume 4; Issue 3. The Inert and the Noble. A G Samuelson. Article-in-a-Box Volume 4 Issue 3 March 1999 pp 3-5 ... Author Affiliations. A G Samuelson1. Department of Inorganic and Physical Chemistry, Indian Institute of Science, Bangalore, India.

Experimental studies and model analysis of noble gas fractionation in porous media

Science.gov (United States)

Ding, Xin; Kennedy, B. Mack.; Evans, William C.; Stonestrom, David A.

2016-01-01

The noble gases, which are chemically inert under normal terrestrial conditions but vary systematically across a wide range of atomic mass and diffusivity, offer a multicomponent approach to investigating gas dynamics in unsaturated soil horizons, including transfer of gas between saturated zones, unsaturated zones, and the atmosphere. To evaluate the degree to which fractionation of noble gases in the presence of an advective–diffusive flux agrees with existing theory, a simple laboratory sand column experiment was conducted. Pure CO2 was injected at the base of the column, providing a series of constant CO2 fluxes through the column. At five fixed sampling depths within the system, samples were collected for CO2 and noble gas analyses, and ambient pressures were measured. Both the advection–diffusion and dusty gas models were used to simulate the behavior of CO2 and noble gases under the experimental conditions, and the simulations were compared with the measured depth-dependent concentration profiles of the gases. Given the relatively high permeability of the sand column (5 ´ 10−11 m2), Knudsen diffusion terms were small, and both the dusty gas model and the advection–diffusion model accurately predicted the concentration profiles of the CO2 and atmospheric noble gases across a range of CO2 flux from ?700 to 10,000 g m−2 d−1. The agreement between predicted and measured gas concentrations demonstrated that, when applied to natural systems, the multi-component capability provided by the noble gases can be exploited to constrain component and total gas fluxes of non-conserved (CO2) and conserved (noble gas) species or attributes of the soil column relevant to gas transport, such as porosity, tortuosity, and gas saturation.

On the methodology of radiochemical neutron activation analysis of noble metals

International Nuclear Information System (INIS)

Chai, C.F.; Ma, S.L.; Mao, X.Y.; Liao, K.N.; Liu, W.C.

1986-01-01

Two different radiochemical procedures were developed: chelate ion resin exchange and amine solvent extraction. Two kinds of new Chinese chelate resins (NANKAI-3926 and BEI-5) and a new long-chain primary amine N 1923 were compared with Srafion NMRR and the tertiary amine N 235 in absorption performance of noble metals, respectively. Influences of various experimental conditions, e.g. sample digestion, acidity, equilibrium time, as well as elution of noble metals, on analytical sensitivity and chemical yield were discussed. Combining with neutron activation, the radiochemical separation procedures developed were used to determine the noble metal contents in the geological samples from Permina/Triassic boundary in South China. (author)

A maximum power point tracking algorithm for buoy-rope-drum wave energy converters

Science.gov (United States)

Wang, J. Q.; Zhang, X. C.; Zhou, Y.; Cui, Z. C.; Zhu, L. S.

2016-08-01

The maximum power point tracking control is the key link to improve the energy conversion efficiency of wave energy converters (WEC). This paper presents a novel variable step size Perturb and Observe maximum power point tracking algorithm with a power classification standard for control of a buoy-rope-drum WEC. The algorithm and simulation model of the buoy-rope-drum WEC are presented in details, as well as simulation experiment results. The results show that the algorithm tracks the maximum power point of the WEC fast and accurately.

Radiological analyses of intermediate and low level supercompacted waste drums by VQAD code

International Nuclear Information System (INIS)

Bace, M.; Trontl, K.; Gergeta, K.

2004-01-01

In order to increase the possibilities of the QAD-CGGP code, as well as to make the code more user friendly, modifications of the code have been performed. A general multisource option has been introduced into the code and a user friendly environment has been created through a Graphical User Interface. The improved version of the code has been used to calculate gamma dose rates of a single supercompacted waste drum and a pair of supercompacted waste drums. The results of the calculation were compared with the standard QAD-CGGP results. (author)

Demonstration test on manufacturing 200 l drum inner shielding material for recycling of reactor operating metal scrap

International Nuclear Information System (INIS)

Umemura, A.; Kimura, K.; Ueno, H.

1993-01-01

Low-level reactor wastes should be safely recycled considering those resource values, the reduction of waste disposal volume and environmental effects. The reasonable recycling system of reactor operating metal scrap has been studied and it was concluded that the 200 liter drum inner shielding material is a very promising product for recycling within the nuclear industry. The drum inner shielding material does not require high quality and so it is expected to be easily manufactured by melting and casting from roughly sorted scrap metals. This means that the economical scrap metal recycling system can be achieved by introducing it. Furthermore its use will ensure safety because of being contained in a drum. In order to realize this recycling system with the drum inner shielding material, the demonstration test program is being conducted. The construction of the test facility, which consists of a melting and refining furnace, a casting apparatus, a machining apparatus etc., was finishing in September, 1992

The design of a mechanical referencing system for the rear drum of the Longwall Shearer Coal Miner

Science.gov (United States)

Jones, E. W.; Yang, T. C. H.

1981-01-01

The design of two systems which reference the position of a longwall shearer coal miner to the mine roof of the present cut and of the last cut are presented. This system is part of an automation system that will guide the rear cutting drum in such a manner that the total depth of cut remains constant even though the front drum may be following an undulating roof profile. The rear drum referencing mechanism continually monitors the distance from the mine roof to the floor for the present cut. This system provides a signal to control a constant depth of cut. The last cut follower mechanism continually monitors the distance from the mine roof of the prior cut to the cutting drum. This latter system provides a signal to minimize the step height in the roof between cuts. The dynamic response of this hydraulic-pneumatic and mechanical system is analyzed to determine accumulator size and precharge pressure.

Measurement of VOC permeability of polymer bags and VOC solubility in polyethylene drum liner

International Nuclear Information System (INIS)

Liekhus, K.J.; Peterson, E.S.

1995-03-01

A test program conducted at the Idaho National Engineering Laboratory (INEL) investigated the use of a transport model to estimate the volatile organic compound (VOC) concentration in the void volume of a waste drum. Unsteady-state VOC transport model equations account for VOC permeation of polymer bags, VOC diffusion across openings in layers of confinement, and VOC solubility in a polyethylene drum liner. In support of this program, the VOC permeability of polymer bags and VOC equilibrium concentration in a polyethylene drum liner were measured for nine VOCs. The VOCs used in experiments were dichloromethane, carbon tetrachloride, cyclohexane, toluene, 1,1,1-trichloroethane, methanol, 1,1,2-trichloro-1,2,2-trifluoroethane (Freon-113), trichloroethylene, and p-xylene. The experimental results of these measurements as well as a method of estimating both parameters in the absence of experimental data are described in this report

Elastic Elements in a Wrist Prosthesis for Drumming Reduce Muscular Effort, but Increase Imprecision and Perceived Stress

Directory of Open Access Journals (Sweden)

Georg Stillfried

2018-03-01

Full Text Available Recently, progress has been made in the development of mechanical joints with variable intrinsic stiffness, opening up the search for application areas of such variable-stiffness joints. By varying the stiffness of its joints, the resonant frequency of a system can be tuned to perform cyclical tasks most energy-efficiently, making the variable-stiffness joint a candidate element for an advanced prosthetic device specifically designed for the cyclical task of drumming. A prerequisite for a successful variable-stiffness drumming prosthesis is the ability of human drummers to profitably employ different stiffness levels for playing different beats. In this pilot study, 29 able-bodied subjects (20 drumming novices and 9 experts wear a cuff on the forearm, to which a drumstick is connected using changeable adapters, consisting of several leaf springs with different stiffness and one maximally stiff connection element. The subjects are asked to play simple regular drum beats at different frequencies, one of which is the resonant frequency of the adapter-drumstick system. The subject's performance of each drumming task is rated in terms of accuracy and precision, and the effort is measured using questionnaires for the perceived stress as well as electromyography (EMG for the muscular activity. The experiments show that using springs instead of the stiff connection leads to lower muscular activity, indicating that humans are able to use the energy-storing capabilities of the springs, or that muscular activity is reduced due to the lower mass of the springs. However, the perceived stress is increased and the novices' performance lowered, possibly due to a higher cerebral load for controlling the elastic system. The hypothesis that “matching the resonant frequency of the spring-drumstick system to the desired frequency leads to better performance and lower effort” is not confirmed. Possible explanations are discussed. In conclusion, a series

Elastic Elements in a Wrist Prosthesis for Drumming Reduce Muscular Effort, but Increase Imprecision and Perceived Stress

Science.gov (United States)

Stillfried, Georg; Stepper, Johannes; Neppl, Hannah; Vogel, Jörn; Höppner, Hannes

2018-01-01

Recently, progress has been made in the development of mechanical joints with variable intrinsic stiffness, opening up the search for application areas of such variable-stiffness joints. By varying the stiffness of its joints, the resonant frequency of a system can be tuned to perform cyclical tasks most energy-efficiently, making the variable-stiffness joint a candidate element for an advanced prosthetic device specifically designed for the cyclical task of drumming. A prerequisite for a successful variable-stiffness drumming prosthesis is the ability of human drummers to profitably employ different stiffness levels for playing different beats. In this pilot study, 29 able-bodied subjects (20 drumming novices and 9 experts) wear a cuff on the forearm, to which a drumstick is connected using changeable adapters, consisting of several leaf springs with different stiffness and one maximally stiff connection element. The subjects are asked to play simple regular drum beats at different frequencies, one of which is the resonant frequency of the adapter-drumstick system. The subject's performance of each drumming task is rated in terms of accuracy and precision, and the effort is measured using questionnaires for the perceived stress as well as electromyography (EMG) for the muscular activity. The experiments show that using springs instead of the stiff connection leads to lower muscular activity, indicating that humans are able to use the energy-storing capabilities of the springs, or that muscular activity is reduced due to the lower mass of the springs. However, the perceived stress is increased and the novices' performance lowered, possibly due to a higher cerebral load for controlling the elastic system. The hypothesis that “matching the resonant frequency of the spring-drumstick system to the desired frequency leads to better performance and lower effort” is not confirmed. Possible explanations are discussed. In conclusion, a series-elastic element appears to

Recovery of noble metals from HLLW using photocatalytic reduction

International Nuclear Information System (INIS)

Nishi, T.; Uetake, N.; Kawamura, F.; Yusa, H.

1987-01-01

In high-level liquid waste (HLLW) from fuel reprocessing plants, noble metals (palladium, rhodium, and ruthenium), which account for ∼ 10 wt% of fission products, exist as ions. These metals are very useful as catalytic material in automobile exhaust systems and other chemical processes, but they are rare in nature, making their recovery from fission products highly desirable. The ions of noble metals in solution have the feature that their reduction potential from ion to metal is relatively high compared with that of other fission product ions, so they can be selectively separated as a metal by a reduction process. The authors think a photoreduction process using a photocatalysts, which functions as photon-electron conversion agent, is suitable for the recovery of noble metals from HLLW for three reasons: (1) this process uses no reduction agents, which usually degrade the nitric acid, so that coprecipitation of other fission products does not occur. (2) The reactions are induced by light, which does not contaminate the reaction system, and in contrast with ordinary photo-redox reactions, the quantum yield is quite high. (3) As the photocatalyst does not change in the reaction, it can be used again and again. The report shows the results of fundamental experiments on the application of photocatalytic reduction to the recovery of noble metal ions in nitric acid solution

Noble Gas Signatures in Groundwater and Rainwater on the Island of Maui, Hawaii - Developing a New Noble Gas Application in Fractured, Volcanic Systems

Science.gov (United States)

Castro, M. C.; Niu, Y.; Warrier, R. B.; Hall, C. M.; Gingerich, S. B.; Scholl, M. A.; Bouvier, L.

2014-12-01

Recent work in the Galapagos Islands suggests that noble gas temperatures (NGTs) in fractured groundwater systems reflect the temperature of the ground surface at the time of infiltration rather than the mean annual air temperature (MAAT) value as commonly assumed in sedimentary systems where NGTs are typically used as indicators of past climate. This suggests that noble gases in fractured areas may record seasonality, and thus, provide information about timing of recharge in addition to location. Calculation of NGTs assumes that rain-derived recharge at the water table is in equilibrium with ground air. Lack of noble gas equilibration with respect to surface conditions, however, was observed in high-altitude springs in the Galapagos Islands and in a rainwater pilot study in Michigan, supporting the NGT seasonality hypothesis. Developing this new NGT application will lead to a better understanding of fractured groundwater flow systems and will contribute to improved water resource management plans. This study, carried out on Maui, Hawaii, is meant to test these hypotheses while improving knowledge of this island's groundwater flow system where limited hydrologic data are available. Here, we present the first results of noble gas analyses from samples collected in springs, groundwater wells and rainwater on northeast Maui. Results show that like most Michigan rainwater samples, rainwater from Maui is in disequilibrium with surface conditions and follows a mass-dependent pattern. Spring samples follow a similar pattern to that of rainwater and suggest that spring water originates directly from rainfall. These findings further support the hypothesis of NGT seasonality. However, while the atmospheric composition of noble gases points to direct supply from rainfall to spring aquifer systems, a direct connection between spring water and deeper aquifer levels or the mantle is apparent from He isotopic ratios which display an almost pure He mantle component in some springs.

Calculation of a thermostressed state for drum-separator vessels in transient regimes

International Nuclear Information System (INIS)

Il'in, Yu.V.; Kazakova, T.Yu.; Parafilo, L.M.; Shcherbakov, S.I.

1979-01-01

The temperature regime and stressed state of the drum-separator vessel in the transient regime with alternating pressure and water level are investigated using calculations. The temperature fields are calculated by the alternating directions method. Stresses and deformations are calculated by the method of finite elements. The stressed state of the vessel is determined for a series of fixed time moments tausub(i), when the T(tausub(i), r, phi) temperature distribution and P(tausub(i)) internal pressure are known. The methods described are used while developing the calculation program for the temperatures and stressed state (FORTRAN, EC-1050). Given are the calculation results obtained using these programs for the processes following the safety system response at the first block of the Bilibinsk NPP and the processes of power regulation in the ''Sever-2'' facility. The comparison of the obtained calculated curves with the experimental data confirms fitness of the proposed calculated scheme for description of the real processes taking place in the drum-separator vessels in the transient regimes. It is emphasized that the given scheme of solution of the equations describing a thermostressed state of the drum-separator vessels can be used while estimating their operation capacity

Time-dependent behavior of positrons in noble gases

International Nuclear Information System (INIS)

Wadehra, J.M.

1990-01-01

Both equilibrium and nonequilibrium behaviors of positrons in several noble gases are reviewed. Our novel procedure for obtaining the time-dependent behavior of various swarm parameters -- such as the positron drift velocity, average positron energy, positron annihilation rate (or equivalently Z eff ) etc. -- for positrons in pure ambient gases subjected to external electrostatic fields is described. Summaries of time-dependent as well as electric field-dependent results for positron swarms in various noble gases are presented. New time-dependent results for positron swarms in neon are also described in detail. 36 refs., 4 figs., 3 tabs

The prevalent synthesis of one-dimensional noble metal nanostructures based on sulfonated polyaniline at room temperature

International Nuclear Information System (INIS)

Xia Youyi

2011-01-01

We describe a prevalent method of synthesizing one-dimensional (1D) noble metal nanostructures (silver nanobelts and palladium nanowires) by treatment of corresponding noble metal ions only in the presence of the conductive sulfonated polyaniline without using any other reducing agents or energies. The results show that the sulfonated polyaniline provides the dual reductant and “soft template” roles to promoting noble metal ions to form shape-controlled 1D noble metal nanostructures in high yield. The employed approach may also shed some light on the preparation of other noble metal nanostructure by using conductive polymer.

Development of Non-Noble Metal Ni-Based Catalysts for Dehydrogenation of Methylcyclohexane

KAUST Repository

Shaikh Ali, Anaam

2016-01-01

to TOL has only been achieved using the noble Pt-based catalysts. The aim of this study is to develop non-noble, cost-effective metal catalysts that can show excellent catalytic performance, mainly maintaining high TOL selectivity achievable by Pt based

Impact of Different Standard Type A7A Drum Closure-Ring Practices on Gasket Contraction and Bolt Closure Distance– 15621

Energy Technology Data Exchange (ETDEWEB)

Ketusky, Edward [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Blanton, Paul [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Bobbitt, John H. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2015-03-11

The Department of Energy, the Savannah River National Laboratory, several manufacturers of specification drums, and the United States Department of Transportation (DOT) are collaborating in the development of a guidance document for DOE contractors and vendors who wish to qualify containers to DOT 7A Type A requirements. Currently, the effort is focused on DOT 7A Type A 208-liter (55-gallons) drums with a standard 12-gauge bolted closure ring. The U.S. requirements, contained in Title 49, Part 178.350 “Specification 7A; general packaging, Type A specifies a competent authority review of the packaging is not required for the transport of (Class 7) radioactive material containing less than Type A quantities of radioactive material. For Type AF drums, a 4 ft. regulatory free drop must be performed, such that the drum “suffers maximum damage.” Although the actual orientation is not defined by the specification, recent studies suggest that maximum damage would result from a shallow angle top impact, where kinetic energy is transferred to the lid, ultimately causing heavy damage to the lid, or even worse, causing the lid to come off. Since each vendor develops closure recommendations/procedures for the drums they manufacture, key parameters applied to drums during closing vary based on vendor. As part of the initial phase of the collaboration, the impact of the closure variants on the ability of the drum to suffer maximum damage is investigated. Specifically, closure testing is performed varying: 1) the amount of torque applied to the closure ring bolt; and, 2) stress relief protocol, including: a) weight of hammer; and, b) orientation that the hammer hits the closure ring. After closure, the amount of drum lid gasket contraction and the distance that the closure bolt moves through the closure ring is measured.

Predictions and implications of a poisson process model to describe corrosion of transuranic waste drums

International Nuclear Information System (INIS)

Lyon, B.F.; Holmes, J.A.; Wilbert, K.A.

1995-01-01

A risk assessment methodology is described in this paper to compare risks associated with immediate or near-term retrieval of transuranic (TRU) waste drums from bermed storage versus delayed retrieval. Assuming a Poisson process adequately describes corrosion, significant breaching of drums is expected to begin at - 15 and 24 yr for pitting and general corrosion, respectively. Because of this breaching, more risk will be incurred by delayed than by immediate retrieval

Multiloop control of a drum boiler

Directory of Open Access Journals (Sweden)

Alena Kozáková

2014-05-01

Full Text Available The Equivalent Subsystems Method (ESM (Kozáková et al., 2011 is methodology of decentralized controller design in the frequency domain which allows designing local controllers using any SISO frequency domain method. The paper deals with the digital ESM version where digital local PID controllers guaranteeing required performance for the full system are designed for individual equivalent subsystems using the practice-oriented Sine-wave method (Bucz et al., 2012. The proposed decentralized controller design procedure was verified on the nonlinear benchmark drum boiler simulation model (Morilla, 2012.

A membrane inlet mass spectrometry system for noble gases at natural abundances in gas and water samples.

Science.gov (United States)

Visser, Ate; Singleton, Michael J; Hillegonds, Darren J; Velsko, Carol A; Moran, Jean E; Esser, Bradley K

2013-11-15

Noble gases dissolved in groundwater can reveal paleotemperatures, recharge conditions, and precise travel times. The collection and analysis of noble gas samples are cumbersome, involving noble gas purification, cryogenic separation and static mass spectrometry. A quicker and more efficient sample analysis method is required for introduced tracer studies and laboratory experiments. A Noble Gas Membrane Inlet Mass Spectrometry (NG-MIMS) system was developed to measure noble gases at natural abundances in gas and water samples. The NG-MIMS system consists of a membrane inlet, a dry-ice water trap, a carbon-dioxide trap, two getters, a gate valve, a turbomolecular pump and a quadrupole mass spectrometer equipped with an electron multiplier. Noble gases isotopes (4)He, (22)Ne, (38)Ar, (84)Kr and (132)Xe are measured every 10 s. The NG-MIMS system can reproduce measurements made on a traditional noble gas mass spectrometer system with precisions of 2%, 8%, 1%, 1% and 3% for He, Ne, Ar, Kr and Xe, respectively. Noble gas concentrations measured in an artificial recharge pond were used to monitor an introduced xenon tracer and to reconstruct temperature variations to within 2 °C. Additional experiments demonstrated the capability to measure noble gases in gas and in water samples, in real time. The NG-MIMS system is capable of providing analyses sufficiently accurate and precise for introduced noble gas tracers at managed aquifer recharge facilities, groundwater fingerprinting based on excess air and noble gas recharge temperature, and field and laboratory studies investigating ebullition and diffusive exchange. Copyright © 2013 John Wiley & Sons, Ltd.

Noble gas separation with the use of inorganic adsorbents

International Nuclear Information System (INIS)

Pence, D.T.; Chou, C.C.; Christian, J.D.; Paplawsky, W.J.

1979-01-01

A noble gas separation process is proposed for application to airborne nuclear fuel reprocessing plant effluents. The process involves the use of inorganic adsorbents for the removal of contaminant gases and noble gas separation through selective adsorption. Water and carbon dioxide are removed with selected zeolites that do not appreciably adsorb the noble gases. Xenon is essentially quantitatively removed with a specially developed adsorbent using conventional adsorption-desorption techniques. Oxygen is removed to low ppM levels by the use of a rapid cycle adsorption technique on a special adsorbent leaving a krypton-nitrogen mixture. Krypton is separated from nitrogen with a special adsorbent operated at about -80 0 C. Because the separation process does not require high pressures and oxygen is readily removed to sufficiently limit ozone formation to insignificant levels, appreciable capital and operating cost savings with this process are possible compared with other proposed processes. In addition, the proposed process is safer to operate

NOBLE - Flexible concept recognition for large-scale biomedical natural language processing.

Science.gov (United States)

Tseytlin, Eugene; Mitchell, Kevin; Legowski, Elizabeth; Corrigan, Julia; Chavan, Girish; Jacobson, Rebecca S

2016-01-14

Natural language processing (NLP) applications are increasingly important in biomedical data analysis, knowledge engineering, and decision support. Concept recognition is an important component task for NLP pipelines, and can be either general-purpose or domain-specific. We describe a novel, flexible, and general-purpose concept recognition component for NLP pipelines, and compare its speed and accuracy against five commonly used alternatives on both a biological and clinical corpus. NOBLE Coder implements a general algorithm for matching terms to concepts from an arbitrary vocabulary set. The system's matching options can be configured individually or in combination to yield specific system behavior for a variety of NLP tasks. The software is open source, freely available, and easily integrated into UIMA or GATE. We benchmarked speed and accuracy of the system against the CRAFT and ShARe corpora as reference standards and compared it to MMTx, MGrep, Concept Mapper, cTAKES Dictionary Lookup Annotator, and cTAKES Fast Dictionary Lookup Annotator. We describe key advantages of the NOBLE Coder system and associated tools, including its greedy algorithm, configurable matching strategies, and multiple terminology input formats. These features provide unique functionality when compared with existing alternatives, including state-of-the-art systems. On two benchmarking tasks, NOBLE's performance exceeded commonly used alternatives, performing almost as well as the most advanced systems. Error analysis revealed differences in error profiles among systems. NOBLE Coder is comparable to other widely used concept recognition systems in terms of accuracy and speed. Advantages of NOBLE Coder include its interactive terminology builder tool, ease of configuration, and adaptability to various domains and tasks. NOBLE provides a term-to-concept matching system suitable for general concept recognition in biomedical NLP pipelines.

Lawrence Livermore National Laboratory Experience Using 30-Gallon Drum Neutron Multiplicity Counter for Measuring Plutonium-Bearing Salts

International Nuclear Information System (INIS)

Dearborn, D M; Keeton, S C

2004-01-01

Lawrence Livermore National Laboratory (LLNL) has been performing accountability measurements of plutonium (Pu) -bearing items with the 30-gallon drum neutron multiplicity counter (NMC) since August 1998. A previous paper focused on the LLNL experience with Pu-bearing oxide and metal items. This paper expands on the LLNL experience with Pu-bearing salts containing low masses of Pu. All Pu-bearing salts used in this study were measured using calorimetry and gamma isotopic analyses (Cal/Iso) as well as the 30-gallon drum NMC. The Cal/Iso values were treated as being the true measure of Pu content because of the inherent high accuracy of the Cal/Iso technique, even at low masses of Pu, when measured over a sufficient period of time. Unfortunately, the long time period required to achieve high accuracy from Cal/Iso can impact other required accountability measurements. The 30-gallon drum NMC is a much quicker system for making accountability measurements of a Pu-bearing salt and might be a desirable tradeoff. The accuracy of 30-gallon drum NMC measurements of Pu-bearing salts, relative to that of Cal/Iso, is presented in relation to the mass range and alpha associated with each item. Conclusions drawn from the use of the 30-gallon drum NMC for accountability measurements of salts are also included

Quality management for noble gas trace analysis; Qualitaetssicherung bei der Edelgasspurenanalyse

Energy Technology Data Exchange (ETDEWEB)

Schmid, S.; Konrad, M.; Kumberg, T.; Schlosser, C. [Bundesamt fuer Strahlenschutz (BfS), Freiburg (Germany); Gohla, H. [Comprehensive Nuclear-Test-Ban Treaty Organization (CTBTO), Vienna International Centre, Vienna (Austria). Preparatory Commission

2014-01-20

The Federal Office for Radiation Protection operates measurement systems to determine the activity concentrations of Krypton-85 and Xenon-133 in air samples since the early 70s. Certified standards with stable noble gas admixtures are still missing for quality assurance (certified activity concentrations). The Comprehensive Nuclear-Test-Ban Treaty Organization (CTBTO) is currently establishing a global noble gas monitoring network for the verification of compliance with the Treaty. In cooperation with CTBTO the BfS currently develops concepts of quality assurance for noble gas measurements. Opportunities for quality assurance without using certified standards are discussed by comparisons between individual laboratories and internal audits. The results from the first CTBTO laboratory intercomparison with synthetic radioxenon samples look very promising.

Corrosion susceptibility of steel drums to be used as containers for intermediate level nuclear waste

International Nuclear Information System (INIS)

Farina, S.; Schulz Rodriguez, F.; Duffo, G.

2013-01-01

The present work is a study of the corrosion susceptibility of steel drums in contact with cemented ion-exchange resins contaminated with different types and concentrations of aggressive species. A special type of specimen was manufactured to simulate the cemented ion-exchange resins in the drum. The evolution of the corrosion potential and the corrosion rate of the steel, as well as the electrical resistivity of the matrix were monitored over a time period of 900 days. The aggressive species studied were chloride ions (the main ionic species of concern) and sulphate ions (produced during radiolysis of the cationic exchange-resins after cementation). The work was complemented with an analysis of the corrosion products formed on the steel in each condition, as well as the morphology of the corrosion products. When applying the results obtained in the present work to estimate the corrosion depth of the steel drums containing the cemented radioactive waste after a period of 300 years (foreseen durability of the Intermediate Level Radioactive Waste facility in Argentina), it is found that in the most unfavourable case (high chloride contamination), the corrosion penetration will be considerably lower than the thickness of the wall of the steel drums. (authors)

Calibration of new measuring systems to detect emissions of radioactive noble gases

International Nuclear Information System (INIS)

Winkelmann, I.; Kreiner, H.J.

1977-12-01

This report describes the calibration of different systems for the integral measurement of radioactive noble gases and the calibration of a measuring chamber for the detection of individual nuclides of radioactive noble gases in the gaseous effluent of nuclear power plants. For these measuring chambers the calibration factors for Kr-85 and Xe-133 are given as well as the detection limits to be obtained with these measuring systems for several radioactive noble gases present in the gaseous effluent at the stack of nuclear power plants. Calibration factors for Kr-85 and Xe-133 and the detection limits of this measuring method for the detections of individual nuclides of radioactive noble gases in air samples are defined taken wirh a high pressure compressor in pressure flasks an measured on a Ge(Li)-semiconductor spectrometer (pressure flask measuring method). A measuring equipment is described and calibrated which allows simultaneous measurement of activity concentration of radioactive noble gases and radioactive aerosols with a sensitivity of 2 x 10 -7 Ci/m 3 for radioactive gases and 1 x 10 -9 Ci/m 3 for radioactive particulates at a background radiation of 1 R/h. This paper is an additional report to our STH-Bericht 3/76, 'Calibration of measuring equipment for monitoring of gaseous effluents from nuclear power plants', which specifies a procedure for the calibration of measuring chambers for monitoring of gaseous radioactive effluents from nuclear power plants /1/. The calibration system used here makes it possible to simultaneously calibrate several noble gas measuring devices. (orig.) [de

Inert anode containing base metal and noble metal useful for the electrolytic production of aluminum

Science.gov (United States)

Ray, Siba P.; Liu, Xinghua

2000-01-01

An inert anode for production of metals such as aluminum is disclosed. The inert anode comprises a base metal selected from Cu and Ag, and at least one noble metal selected from Ag, Pd, Pt, Au, Rh, Ru, Ir and Os. The inert anode may optionally be formed of sintered particles having interior portions containing more base metal than noble metal and exterior portions containing more noble metal than base metal. In a preferred embodiment, the base metal comprises Cu, and the noble metal comprises Ag, Pd or a combination thereof.

Possible solar noble-gas component in Hawaiian basalts

Energy Technology Data Exchange (ETDEWEB)

Honda, Masahiko; McDougall, I.; Patterson, D.B.; Doulgeris, A. (Australian National Univ., Canberra (Australia). Research School of Earth Sciences); Clague, D.A. (Geological Survey, Menlo Park, CA (USA))

1991-01-10

The noble-gas elemental and isotopic composition in the Earth is significantly different from that of the present atmosphere, and provides an important clue to the origin and history of the Earth and its atmosphere. Possible candidates for the noble-gas composition of the primordial Earth include a solar-like component, a planetary-like component (as observed in primitive meteorites) and a component similar in composition to the present atmosphere. In an attempt to identify the contributions of such components, we have measured isotope ratios of helium and neon in fresh basaltic glasses dredged from Loihi seamount and the East Rift Zone of Kilauea. We find a systematic enrichment in {sup 20}Ne and {sup 21}Ne relative to {sup 22}Ne, compared with atmospheric neon. The helium and neon isotope signatures observed in our samples can be explained by mixing of solar, present atmospheric, radiogenic and nucleogenic components. These data suggest that the noble-gas isotopic composition of the mantle source of the Hawaiian plume is different from that of the present atmosphere, and that it includes a significant solar-like component. We infer that this component was acquired during the formation of the Earth. (author).

Metrological tests of a 200 L calibration source for HPGE detector systems for assay of radioactive waste drums

International Nuclear Information System (INIS)

Boshkova, T.; Mitev, K.

2016-01-01

In this work we present test procedures, approval criteria and results from two metrological inspections of a certified large volume "1"5"2Eu source (drum about 200 L) intended for calibration of HPGe gamma assay systems used for activity measurement of radioactive waste drums. The aim of the inspections was to prove the stability of the calibration source during its working life. The large volume source was designed and produced in 2007. It consists of 448 identical sealed radioactive sources (modules) apportioned in 32 transparent plastic tubes which were placed in a wooden matrix which filled the drum. During the inspections the modules were subjected to tests for verification of their certified characteristics. The results show a perfect compliance with the NIST basic guidelines for the properties of a radioactive certified reference material (CRM) and demonstrate the stability of the large volume CRM-drum after 7 years of operation. - Highlights: • Large (200 L) volume drum source designed, produced and certified as CRM in 2007. • Source contains 448 identical sealed radioactive "1"5"2Eu sources (modules). • Two metrological inspections in 2011 and 2014. • No statistically significant changes of the certified characteristics over time. • Stable calibration source for HPGe-gamma radioactive waste assay systems.

Assessment of DOD Wounded Warrior Matters -- Fort Drum

Science.gov (United States)

2011-09-30

their relation to military duties. The six factors that are evaluated are: physical capacity or stamina , upper extremities, lower extremities...Health Net Federal Services contractor. The Fort Drum MEDDAC Referral Management Office created a “Reports Cell ” which was responsible for obtaining...Care Division had created a CLR/Reports Cell group that focused specifically on obtaining CLRs, inputting them into patients’ AHLTA records and

Feasibility study of {sup 235}U and {sup 239}Pu characterization in radioactive waste drums using neutron-induced fission delayed gamma rays

Energy Technology Data Exchange (ETDEWEB)

Nicol, T. [CEA, DEN, Cadarache, Nuclear Measurement Laboratory, F-13108 Saint-Paul-lez-Durance (France); FZJ, Institute of Energy and Climate Research – Nuclear Waste Management and Reactor Safety, Wilhelm-Johnen-Straße, d-52425 Jülich (Germany); Pérot, B., E-mail: bertrand.perot@cea.fr [CEA, DEN, Cadarache, Nuclear Measurement Laboratory, F-13108 Saint-Paul-lez-Durance (France); Carasco, C. [CEA, DEN, Cadarache, Nuclear Measurement Laboratory, F-13108 Saint-Paul-lez-Durance (France); Brackx, E. [CEA, DEN, Marcoule, Metallography and Chemical Analysis Laboratory, F-30207 Bagnols-sur-Cèze (France); Mariani, A.; Passard, C. [CEA, DEN, Cadarache, Nuclear Measurement Laboratory, F-13108 Saint-Paul-lez-Durance (France); Mauerhofer, E. [FZJ, Institute of Energy and Climate Research – Nuclear Waste Management and Reactor Safety, Wilhelm-Johnen-Straße, d-52425 Jülich (Germany); Collot, J. [Laboratoire de Physique Subatomique et de Cosmologie, Université Grenoble Alpes, CNRS/IN2P3 Grenoble (France)

2016-10-01

This paper reports a feasibility study of {sup 235}U and {sup 239}Pu characterization in 225 L bituminized waste drums or 200 L concrete waste drums, by detecting delayed fission gamma rays between the pulses of a deuterium-tritium neutron generator. The delayed gamma yields were first measured with bare samples of {sup 235}U and {sup 239}Pu in REGAIN, a facility dedicated to the assay of 118 L waste drums by Prompt Gamma Neutron Activation Analysis (PGNAA) at CEA Cadarache, France. Detectability in the waste drums is then assessed using the MCNPX model of MEDINA (Multi Element Detection based on Instrumental Neutron Activation), another PGNAA cell dedicated to 200 L drums at FZJ, Germany. For the bituminized waste drum, performances are severely hampered by the high gamma background due to {sup 137}Cs, which requires the use of collimator and shield to avoid electronics saturation, these elements being very penalizing for the detection of the weak delayed gamma signal. However, for lower activity concrete drums, detection limits range from 10 to 290 g of {sup 235}U or {sup 239}Pu, depending on the delayed gamma rays of interest. These detection limits have been determined by using MCNPX to calculate the delayed gamma useful signal, and by measuring the experimental gamma background in MEDINA with a 200 L concrete drum mock-up. The performances could be significantly improved by using a higher interrogating neutron emission and an optimized experimental setup, which would allow characterizing nuclear materials in a wide range of low and medium activity waste packages.

Pre-title I safety evaluation for the retrieval operations of transuranic waste drums in the Solid Waste Disposal Facility. Revision 2

International Nuclear Information System (INIS)

Rabin, M.S.

1992-08-01

Phase I of the Transuranic (TRU) Waste Facility Line Item Project includes the retrieval and safe storage of the pad drums that are stored on TRU pads 2-6 in the Solid Waste Disposal Facility (SWDF). Drums containing TRU waste were placed on these pads as early as 1974. The pads, once filled, were mounded with soil. The retrieval activities will include the excavation of the soil, retrieval of the pad drums, placing the drums in overpacks (if necessary) and venting and purging the retrieved drums. Once the drums have been vented and purged, they will be transported to other pads within the SWDF or in a designated area until they are eventually treated as necessary for ultimate shipment to the Waste Isolation Pilot Plant in Carlsbad, New Mexico. This safety evaluation provides a bounding assessment of the radiological risk involved with the drum retrieval activities to the maximally exposed offsite individual and the co-located worker. The results of the analysis indicate that the risk to the maximally exposed offsite individual and the co-located worker using maximum frequencies and maximum consequences are within the acceptance criteria defined in WSRC Procedural Manual 9Q. The purpose of this evaluation is to demonstrate the incremental risk from the SWDF due to the retrieval activities for use as design input only. As design information becomes available, this evaluation can be revised to satisfy the safety analysis requirements of DOE Orders 4700 and 5480.23

Estimated Uncertainty in Segmented Gamma Scanner Assay Results due to the Variation in Drum Tare Weights

International Nuclear Information System (INIS)

Bosko, A.; Croft, St.; Gulbransen, E.

2009-01-01

General purpose gamma scanners are often used to assay unknown drums that differ from those used to create the default calibration. This introduces a potential source of bias into the matrix correction when the correction is based on the estimation of the mean density of the drum contents from a weigh scale measurement. In this paper we evaluate the magnitude of this bias that may be introduced by performing assay measurements with a system whose matrix correction algorithm was calibrated with a set of standard drums but applied to a population of drums whose tare weight may be different. The matrix correction factors are perturbed in such cases because the unknown difference in tare weight gets reflected as a bias in the derived matrix density. This would be the only impact if the difference in tare weight was due solely to the weight of the lid or base, say. But in reality the reason for the difference may be because the steel wall of the drum is of a different thickness. Thus, there is an opposing interplay at work which tends to compensate. The purpose of this work is to evaluate and bound the magnitude of the resulting assay uncertainty introduced by tare weight variation. We compare the results obtained using simple analytical models and the 3-D ray tracing with ISOCS software to illustrate and quantify the problem. The numerical results allow a contribution to the Total Measurement Uncertainty (TMU) to be propagated into the final assay result. (authors)

Design and analysis of drum lathe for manufacturing large-scale optical microstructured surface and load characteristics of aerostatic spindle

Science.gov (United States)

Wu, Dongxu; Qiao, Zheng; Wang, Bo; Wang, Huiming; Li, Guo

2014-08-01

In this paper, a four-axis ultra-precision lathe for machining large-scale drum mould with microstructured surface is presented. Firstly, because of the large dimension and weight of drum workpiece, as well as high requirement of machining accuracy, the design guidelines and component parts of this drum lathe is introduced in detail, including control system, moving and driving components, position feedback system and so on. Additionally, the weight of drum workpiece would result in the structural deformation of this lathe, therefore, this paper analyses the effect of structural deformation on machining accuracy by means of ANSYS. The position change is approximately 16.9nm in the X-direction(sensitive direction) which could be negligible. Finally, in order to study the impact of bearing parameters on the load characteristics of aerostatic journal bearing, one of the famous computational fluid dynamics(CFD) software, FLUENT, is adopted, and a series of simulations are carried out. The result shows that the aerostatic spindle has superior performance of carrying capacity and stiffness, it is possible for this lathe to bear the weight of drum workpiece up to 1000kg since there are two aerostatic spindles in the headstock and tailstock.

Isotopic mass-dependence of noble gas diffusion coefficients inwater

Energy Technology Data Exchange (ETDEWEB)

Bourg, I.C.; Sposito, G.

2007-06-25

Noble gas isotopes are used extensively as tracers inhydrologic and paleoclimatic studies. These applications requireknowledge of the isotopic mass (m) dependence of noble gas diffusioncoefficients in water (D), which has not been measured but is estimatedusing experimental D-values for the major isotopes along with an untestedrelationship from kinetic theory, D prop m-0.5. We applied moleculardynamics methods to determine the mass dependence of D for four noblegases at 298 K, finding that D prop m-beta with beta<0.2, whichrefutes the kinetic theory model underlying all currentapplications.

Metrological tests of a 200 L calibration source for HPGE detector systems for assay of radioactive waste drums.

Science.gov (United States)

Boshkova, T; Mitev, K

2016-03-01

In this work we present test procedures, approval criteria and results from two metrological inspections of a certified large volume (152)Eu source (drum about 200L) intended for calibration of HPGe gamma assay systems used for activity measurement of radioactive waste drums. The aim of the inspections was to prove the stability of the calibration source during its working life. The large volume source was designed and produced in 2007. It consists of 448 identical sealed radioactive sources (modules) apportioned in 32 transparent plastic tubes which were placed in a wooden matrix which filled the drum. During the inspections the modules were subjected to tests for verification of their certified characteristics. The results show a perfect compliance with the NIST basic guidelines for the properties of a radioactive certified reference material (CRM) and demonstrate the stability of the large volume CRM-drum after 7 years of operation. Copyright © 2015 Elsevier Ltd. All rights reserved.

Noble Gas Release Signal as a Precursor to Fracture

Science.gov (United States)

Bauer, S. J.; Lee, H.; Gardner, W. P.

2017-12-01

We present empirical results of rock strain, microfracturing, acoustic emissions, and noble gas release from laboratory triaxial experiments for a granite, basalt, shale and bedded rock salt. Noble gases are released and measured real-time during deformation using mass spectrometry. The gas release represents a precursive signal to macrofracture. Gas release is associated with increased acoustic emissions indicating that microfracturing is required to release gas and create pathways for the gas to be sensed. The gas released depends on initial gas content, pore structure and its evolution during deformation, the deformation amount, matrix permeability, deformation style and the stress/strain history. Gases are released from inter and intracrystalline sites; release rate increases as strain and microfracturing increases. The gas composition depends on lithology, geologic history and age, fluids present, and radioisotope concentrations that affect radiogenic noble gas isotope (e.g. 4He,40Ar) production. Noble gas emission and its relationship to crustal processes such as seismicity and volcanism, tectonic velocities, qualitative estimates of deep permeability, age dating of groundwater, and a signature of nuclear weapon detonation. Our result show that mechanical deformation of crustal materials is an important process controlling gas release from rocks and minerals, and should be considered in techniques which utilize gas release and/or accumulation. We propose using noble gas release to signal rock deformation in boreholes, mines and waste repositories. We postulate each rock exhibits a gas release signature which is microstructure, stress, strain, and/or permanent deformation dependent. Calibration of such relationships, for example relating gas release per rock unit volume to strain may be used to quantify rock deformation and develop predictive models.Sandia National Laboratories is a multimission laboratory managed and operated by National Technology and

An ABC of Drumming: Children's Narratives about Beat, Rhythm and Groove in a Primary Classroom

Science.gov (United States)

Mackinlay, Elizabeth

2014-01-01

In this paper, I use a bricolage of arts-based research and writing practices to explore narratives by Grade 4 children about their experiences in a drumming circle called "Bam Bam" as represented in a text they created with me called An ABC of drumming. The term "narrative" is used here in a contemporary sense to…

Low-level waste drum staging building at Weapons Engineering Tritium Facility, TA-16, Los Alamos National Laboratory, Los Alamos, New Mexico. Environmental Assessment

International Nuclear Information System (INIS)

1994-08-01

The proposed action is to place a 3 meter (m) by 4.5 m (10 ft x 15 ft) prefabricated storage building (transportainer) adjacent to the existing Weapons Engineering Tritium Facility (WETF) at Technical Area (TA-) 16, Los Alamos National Laboratory (LANL), and to use the building as a staging site for sealed 55 galllon drums of noncompactible waste contaminated with low levels of tritium (LLW). Up to eight drums of waste would be accumulated before the waste is moved by LANL Waste Management personnel to the existing on-site LLW disposal area at TA-54. The drum staging building would be placed on a bermed asphalt pad, near other existing accumulation structures for office trash and compactible LLW. The no-action alternative is to continue storing drums of LLW in the WETF laboratories where they occupy valuable work space, hamper movement of personnel and equipment, and require waste management personnel to enter those laboratories in order to remove filled drums. No new waste would be generated by implementing the proposed action; no changes or increases in WETF operations or waste production rate are anticipated as a result of staging drums of LLW outside the main laboratory building. The site for the LLW drum staging building would not impact any sensitive areas. Tritium emissions from the drums of LLW were included within the source term for normal operations at the WETF; the cumulative impacts would not be increased

Hanford contact-handled transuranic drum retrieval project planning document

International Nuclear Information System (INIS)

DEMITER, J.A.

1998-01-01

The Hanford Site is one of several US Department of Energy (DOE) sites throughout the US that has generated and stored transuranic (TRU) wastes. The wastes were primarily placed in 55-gallon drums, stacked in trenches, and covered with soil. In 1970, the Nuclear Regulatory Commission ordered that TRU wastes be segregated from other radioactive wastes and placed in retrievable storage until such time that the waste could be sent to a geologic repository and permanently disposed. Retrievable storage also defined container storage life by specifying that a container must be retrievable as a contamination-free container for 20 years. Hanford stored approximately 37,400 TRU containers in 20-year retrievable storage from 1970 to 1988. The Hanford TRU wastes placed in 20-year retrievable storage are considered disposed under existing Resource Conservation and Recovery Act (RCRA) regulations since they were placed in storage prior to September 1988. The majority of containers were 55-gallon drums, but 20-year retrievable storage includes several TRU wastes covered with soil in different storage methods

Production of spheroidal graphite cast iron (S. G. Iron) for an automobile brake drum

International Nuclear Information System (INIS)

Butt, M.T.Z.; Aziz, S.

2005-01-01

The role of automobile industry for any country has a great importance. Break drum is one of the essential parts of automobile car and its local casting is required in order to achieve the target for automobile industry because it has special significance. Break drum being the important constituent of the system of an automobile requires a great degree of accuracy and reliability. S. G. Iron is preferred because of its mechanical properties i.e., higher strength modulus, impact resistance and ductility along with excellent machinability and manufacturing ease. (author)

Noble gas control room accident filtration system for severe accident conditions (N-CRAFT)

International Nuclear Information System (INIS)

Hill, Axel; Stiepani, Cristoph; Drechsler, Michael

2015-01-01

Severe accidents might cause the release of airborne radioactive substances to the environment of the NPP either due to containment leakages or due to intentional filtered containment venting. In the latter case aerosols and iodine are retained, however noble gases are not retainable by the FCVS or by conventional air filtration systems like HEPA filters and iodine absorbers. Radioactive noble gases nevertheless dominate the activity release depending on the venting procedure and the weather conditions. To prevent unacceptable contamination of the control room atmosphere by noble gases, AREVA GmbH has developed a noble gas control room accident filtration system (CRAFT) which can supply purified fresh air to the control room without time limitation. The retention process is based on dynamic adsorption of noble gases on activated carbon. The system consists of delay lines (carbon columns) which are operated by a continuous and simultaneous adsorption and desorption process. CRAFT allows minimization of the dose rate inside the control room and ensures low radiation exposure to the staff by maintaining the control room environment suitable for prolonged occupancy throughout the duration of the accident. CRAFT consists of a proven modular design either transportable or permanently installed. (author)

Noble gas enrichment studies at JET

International Nuclear Information System (INIS)

Groth, M.; Andrew, P.; Fundamenski, W.; Guo, H.Y.; Hillis, D.L.; Hogan, J.T.; Horton, L.D.; Matthews, G.F.; Meigs, A.G.; Morgan, P.M.; Stamp, M.F.; Hellermann, M. von

2001-01-01

Adequate helium exhaust has been achieved in reactor-relevant ELMy H-mode plasmas in JET performed in the MKII AP and MKII GB divertor geometry. The divertor-characteristic quantities of noble gas compression and enrichment have been experimentally inferred from Charge Exchange Recombination Spectroscopy measurements in the core plasma, and from spectroscopic analysis of a Penning gauge discharge in the exhaust gas. The retention of helium was found to be satisfactory for a next-step device, with enrichment factors exceeding 0.1. The helium enrichment decreases with increasing core plasma density, while the neon enrichment has the opposite behaviour. Analytic and numerical analyses of these plasmas using the divertor impurity code package DIVIMP/NIMBUS support the explanation that the enrichment of noble gases depends significantly on the penetration depth of the impurity neutrals with respect to the fuel atoms. Changes of the divertor plasma configuration and divertor geometry have no effect on the enrichment

Probing the interaction of noble gases with pristine and nitrogen-doped graphene through Raman spectroscopy

Science.gov (United States)

Cunha, Renato; Perea-López, Néstor; Elías, Ana Laura; Fujisawa, Kazunori; Carozo, Victor; Feng, Simin; Lv, Ruitao; dos Santos, Maria Cristina; Terrones, Mauricio; Araujo, Paulo T.

2018-05-01

The interactions of adsorbates with graphene have received increasing attention due to its importance in the development of applications involving graphene-based coatings. Here, we present a study of the adsorption of noble gases on pristine and nitrogen-doped graphene. Single-layer graphene samples were synthesized by chemical vapor deposition (CVD) and transferred to transmission electron microscopy (TEM) grids. Several noble gases were allowed to adsorb on the suspended graphene substrate at very low temperatures. Raman spectra show distinct frequency blue shifts in both the 2D and G bands, which are induced by gas adsorption onto high quality single layer graphene (1LG). These shifts, which we associate with compressive biaxial strain in the graphene layers induced by the noble gases, are negligible for nitrogen-doped graphene. Additionally, a thermal depinning transition, which is related to the desorption of a noble gas layer from the graphene surface at low temperatures (ranging from 20 to 35 K), was also observed at different transition temperatures for different noble gases. These transition temperatures were found to be 25 K for argon and 35 K for xenon. Moreover, we were able to obtain values for the compressive biaxial strain in graphene induced by the adsorbed layer of noble gases, using Raman spectroscopy. Ab initio calculations confirmed the correlation between the noble gas-induced strain and the changes in the Raman features observed.

Polarization of stable and radioactive noble gas nuclei by spin exchange with laser pumped alkali atoms

International Nuclear Information System (INIS)

Calaprice, F.; Happer, W.; Schreiber, D.

1984-01-01

The nuclei of noble gases can be strongly polarized by spin exchange with sufficiently dense optically pumped alkali vapors. Only a small fraction of the spin angular momentum of the alkali atoms is transferred to the nuclear spin of the noble gas. Most of the spin angular momentum is lost to translational angular momentum of the alkali and noble gas atoms about each other. For heavy noble gases most of the angular momentum transfer occurs in alkali-noble-gas van der Waals molecules. The transfer efficiency depends on the formation and breakup rates of the van der Waals molecules in the ambient gas. Experimental methods to measure the spin transfer efficiencies have been developed. Nuclei of radioactive noble gases have been polarized by these methods, and the polarization has been detected by observing the anisotropy of the radioactive decay products. Very precise measurements of the magnetic moments of the radioactive nuclei have been made. 12 references, 9 figures

Application of artificial neural networks on the characterization of radioactive waste drums; Aplicacao de redes neurais artificiais na caracterizacao de tambores de rejeito radioativo

Energy Technology Data Exchange (ETDEWEB)

Potiens Junior, Ademar Jose; Hiromoto, Goro, E-mail: apotiens@ipen.b, E-mail: hiromoto@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

2011-10-26

The methodology consist of system simulation of drum-detector by Monte Carlo for obtention of counting efficiency. The obtained data were treated and a neural artificial network (RNA) were constructed for evaluation of total activity of drum. For method evaluation measurements were performed in ten position parallel to the drum axis and the results submitted to the RNA. The developed methodology showed to be effective for isotopic characterization of gamma emitter radioactive wastes distributed in a heterogeneous way in a 200 litters drum. The objective of this work as to develop a methodology of analyse for quantification and localization of radionuclides not homogeneous distributed in a 200 liters drum based on the mathematical techniques

Near transferable phenomenological n-body potentials for noble metals.

Science.gov (United States)

Pontikis, Vassilis; Baldinozzi, Gianguido; Luneville, Laurence; Simeone, David

2017-09-06

We present a semi-empirical model of cohesion in noble metals with suitable parameters reproducing a selected set of experimental properties of perfect and defective lattices in noble metals. It consists of two short-range, n-body terms accounting respectively for attractive and repulsive interactions, the former deriving from the second moment approximation of the tight-binding scheme and the latter from the gas approximation of the kinetic energy of electrons. The stability of the face centred cubic versus the hexagonal compact stacking is obtained via a long-range, pairwise function of customary use with ionic pseudo-potentials. Lattice dynamics, molecular statics, molecular dynamics and nudged elastic band calculations show that, unlike previous potentials, this cohesion model reproduces and predicts quite accurately thermodynamic properties in noble metals. In particular, computed surface energies, largely underestimated by existing empirical cohesion models, compare favourably with measured values, whereas predicted unstable stacking-fault energy profiles fit almost perfectly ab initio evaluations from the literature. All together the results suggest that this semi-empirical model is nearly transferable.

Simultaneous Thermal Analysis of WIPP and LANL Waste Drum Samples: A Preliminary Report

Energy Technology Data Exchange (ETDEWEB)

Wayne, David M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-10-19

On Friday, February 14, 2014, an incident in P7R7 of the WIPP underground repository released radioactive material into the environment. The direct cause of the event was a breached transuranic (TRU) waste container, subsequently identified as Drum 68660. Photographic and other evidence indicates that the breach of 68660 was caused by an exothermic event. Subsequent investigations (Britt, 2015; Clark and Funk, 2015; Wilson et al., 2015; Clark, 2015) indicate that the combination of nitrate salts, pH neutralizing chemicals, and organic-based adsorbent represented a potentially energetic mixture. The materials inside the breached steel drum consisted of remediated, 30- to 40-year old, Pu processing wastes from LANL. The contents were processed and repackaged in 2014. Processing activities at LANL included: 1) neutralization of acidic liquid contents, 2) sorption of the neutralized liquid, and 3) mixing of acidic nitrate salts with an absorber to meet waste acceptance criteria. The contents of 68660 and its sibling, 68685, were derived from the same parent drum, S855793. Drum S855793 originally contained ten plastic bags of acidic nitrate salts, and four bags of mixed nitrate and oxalate salts generated in 1985 by Pu recovery operations. These salts were predominantly oxalic acid, hydrated nitrate salts of Mg, Ca, and Fe, anhydrous Na(NO₃), and minor amounts of anhydrous and hydrous nitrate salts of Pb, Al, K, Cr, and Ni. Other major components include sorbed water, nitric acid, dissolved nitrates, an absorbent (Swheat Scoop®) and a neutralizer (KolorSafe®). The contents of 68660 are described in greater detail in Appendix E of Wilson et al. (2015)

Simultaneous Thermal Analysis of WIPP and LANL Waste Drum Samples: A Preliminary Report

International Nuclear Information System (INIS)

Wayne, David M.

2015-01-01

On Friday, February 14, 2014, an incident in P7R7 of the WIPP underground repository released radioactive material into the environment. The direct cause of the event was a breached transuranic (TRU) waste container, subsequently identified as Drum 68660. Photographic and other evidence indicates that the breach of 68660 was caused by an exothermic event. Subsequent investigations (Britt, 2015; Clark and Funk, 2015; Wilson et al., 2015; Clark, 2015) indicate that the combination of nitrate salts, pH neutralizing chemicals, and organic-based adsorbent represented a potentially energetic mixture. The materials inside the breached steel drum consisted of remediated, 30- to 40-year old, Pu processing wastes from LANL. The contents were processed and repackaged in 2014. Processing activities at LANL included: 1) neutralization of acidic liquid contents, 2) sorption of the neutralized liquid, and 3) mixing of acidic nitrate salts with an absorber to meet waste acceptance criteria. The contents of 68660 and its sibling, 68685, were derived from the same parent drum, S855793. Drum S855793 originally contained ten plastic bags of acidic nitrate salts, and four bags of mixed nitrate and oxalate salts generated in 1985 by Pu recovery operations. These salts were predominantly oxalic acid, hydrated nitrate salts of Mg, Ca, and Fe, anhydrous Na(NO 3 ), and minor amounts of anhydrous and hydrous nitrate salts of Pb, Al, K, Cr, and Ni. Other major components include sorbed water, nitric acid, dissolved nitrates, an absorbent (Swheat Scoop®) and a neutralizer (KolorSafe®). The contents of 68660 are described in greater detail in Appendix E of Wilson et al. (2015)

Analysis of the physical atomic forces between noble gas atoms, alkali ions and halogen ions

Science.gov (United States)

Wilson, J. W.; Heinbockel, J. H.; Outlaw, R. A.

1986-01-01

The physical forces between atoms and molecules are important in a number of processes of practical importance, including line broadening in radiative processes, gas and crystal properties, adhesion, and thin films. The components of the physical forces between noble gas atoms, alkali ions, and halogen ions are analyzed and a data base for the dispersion forces is developed from the literature based on evaluations with the harmonic oscillator dispersion model for higher order coefficients. The Zener model of the repulsive core is used in the context of the recent asymptotic wave functions of Handler and Smith; and an effective ionization potential within the Handler and Smith wave functions is defined to analyze the two body potential data of Waldman and Gordon, the alkali-halide molecular data, and the noble gas crystal and salt crystal data. A satisfactory global fit to this molecular and crystal data is then reproduced by the model to within several percent. Surface potentials are evaluated for noble gas atoms on noble gas and salt crystal surfaces with surface tension neglected. Within this context, the noble gas surface potentials on noble gas and salt crystals are considered to be accurate to within several percent.

Artificial neural network application in isotopic characterization of radioactive waste drums

International Nuclear Information System (INIS)

Potiens Junior, Ademar Jose

2005-01-01

One of the most important aspects to the development of the nuclear technology is the safe management of the radioactive waste arising from several stages of the nuclear fuel cycles, as well as from production and use of radioisotope in the medicine, industry and research centers. The accurate characterization of this waste is not a simple task, given to its diversity in isotopic composition and non homogeneity in the space distribution and mass density. In this work it was developed a methodology for quantification and localization of radionuclides not non homogeneously distributed in a 200 liters drum based in the Monte Carlo Method and Artificial Neural Network (RNA), for application in the isotopic characterization of the stored radioactive waste at IPEN. Theoretical arrangements had been constructed involving the division of the radioactive waste drum in some units or cells and some possible configurations of source intensities. Beyond the determination of the detection positions, the respective detection efficiencies for each position in function of each cell of the drum had been obtained. After the construction and the training of the RNA's for each developed theoretical arrangement, the validation of the method were carried out for the two arrangements that had presented the best performance. The results obtained show that the methodology developed in this study could be an effective tool for isotopic characterization of radioactive wastes contained in many kind of packages. (author)

Final report of the 2. committee of investigation of the 11. legislative period. Drums

International Nuclear Information System (INIS)

1990-01-01

On the subject of 'drums', the questions concerning treatment, transport, and storage and disposal, the content of the drums as well as procedures for persons and environment were in the fore. The Committee dealt with the customary conditioning methods and with the occurrences at Studsvik Energiteknik AB and CEN/SCK in Mol/Belgium, the facilities charged by Transnuklear GmbH with the conditioning. The all in all 1534 drums with waste conditioned in CEN/SCK, which are in German intermediate waste stores, contain to a considerable extent elements from conditioned waste of Belgian origin, despite of having been declared to be waste of German origin. The reasons for this were partly of an operational nature, partly intentionally, in order to fulfil the contracts and to receive the full price. - European and national law were violated. - The Federal Government's main counter- measures consisted in restructuring the nculear energy industry, de-concentration of responsibility sectors, liquidation of Transnuklear GmbH in May 1988, and the guideline on safeguards of radioactive wastes of January 16, 1989. (HSCH) [de

Helium Isotopes and Noble Gas Abundances of Cave Dripping Water in Three Caves in East Asia

Science.gov (United States)

Chen, A. T.; Shen, C. C.; Tan, M.; Li, T.; Uemura, R.; Asami, R.

2015-12-01

Paleo-temperature recorded in nature archives is a critical parameter to understand climate change in the past. With advantages of unique inert chemical characteristics and sensitive solubilities with temperature, dissolved noble gases in speleothem inclusion water were recently proposed to retrieve terrestrial temperature history. In order to accurately apply this newly-developed speleothem noble gas temperature (NGT) as a reliable proxy, a fundamental issue about behaviors of noble gases in the karst should be first clarified. In this study, we measured noble gas contents in air and dripping water to evaluate any ratio deviation between noble gases. Cave dripping water samples was collected from three selected caves, Shihua Cave in northern China, Furong Cave in southwestern, and Gyukusen Cave in an island located in the western Pacific. For these caves are characterized by a thorough mixing and long-term storage of waters in a karst aquifer by the absence of seasonal oxygen isotope shifts. Ratios of dripping water noble gases are statistically insignificant from air data. Helium isotopic ratios in the dripping water samples match air value. The results indicate that elemental and isotopic signatures of noble gases from air can be frankly preserved in the epikarst and support the fidelity of NGT techniques.

The predicted effectiveness of noble metal treatment at the Chinshan boiling water reactor

International Nuclear Information System (INIS)

Yeh Tsungkuang; Chu Fang; Chang Ching; Huang Chiashen

2000-01-01

The technique of noble metal treatment (NMT) available in a form of noble metal cooling (NMC) or noble metal chemical addition (NMCA), was introduced to enhance effectiveness of hydrogen water chemistry. Since it is technically difficult to gain access to an entire primary heat transport circuit (PHTC) of a BWR and monitor variation on electrochemical corrosion potential (ECP), a question whether the NMC technology is indeed effective for lowering the ECP of every location in a BWR is not still well understood at the moment. Then, computer modeling is so far the best tool to help investigate effectiveness of the NMT along PHCT of the BWR. Here was discussed on how the computer model was calibrated by using measured chemistry data obtained from No. 2 unit (BWR) in the Kuosheng Plant. The effect of noble metal treatment coupled with hydrogen water chemistry has been quantitatively molded, on a base of two different sets of ECD enhancement data. It was predicted that No. 1 unit in the Chinshan could be protected by noble metal treatment with lower [H 2 ] FW . In the case of competitive enhancing factors for the ECDs of oxygen reduction, hydrogen peroxide reduction, and hydrogen oxidation reactions, HWC had always to be present for noble metal treatment to be effective for protecting a reactor. Otherwise, according to a model calculation based upon the results from Kim's work, the ECP might instead be increased due to the enhanced reduction reaction rate of oxygen and hydrogen peroxide, especially in the near core regions. (G.K.)

Application of the dose conversion factor for a NaI(Tl) detector to the radwaste drum assay

International Nuclear Information System (INIS)

Ji, Young-Yong; Hong, Dae-Seok; Kim, Tae-Kuk; Kwak, Kyung-Kil; Ryu, Woo-Seog

2011-01-01

The dose-to-curie (DTC) conversion method has been known that there could be extremely high uncertainty associated with establishing the radioactivity of gamma emitters in a drum. However, the DTC conversion method is still an effective assay method to calculate the radioisotope inventory because of the simple and easy procedures to be applied. In order to make the DTC conversion method practical, numerous assumptions and limitations placed on its use. These assumptions and limitations are related to the dose rate measurement and the relative abundance of gamma emitters in a drum. However, these two variables were generally obtained from the different detection mechanisms even using the different radwaste each other. Unfortunately, that expanded the limitation of using the DTC conversion method. In order to obtain two variables in a drum to be assayed at once, the dose conversion factor for a NaI(Tl) detector was first calculated from the MCNP code. The pulse height spectrum from a simulated drum inserted into a standard source was measured by a NaI(Tl) detector, and then, two variables were calculated from the dose conversion factor and the net count rate of detected gamma emitters in the pulse height spectrum.

Characterization of uranium in bituminized radioactive waste drums by self-induced X-ray fluorescence

International Nuclear Information System (INIS)

Pin, Patrick; Perot, Bertrand

2013-06-01

This paper reports the experimental qualification of an original uranium characterization method based on fluorescence X rays induced by the spontaneous gamma emission of bituminized radioactive waste drums. The main 661.7 keV gamma ray following the 137 Cs decay produces by Compton scattering in the bituminized matrix an intense photon continuum around 100 keV, i.e. in the uranium X-ray fluorescence region. 'Self-induced' X-rays produced without using an external source allow a quantitative assessment of uranium as 137 Cs and uranium are homogeneously mixed and distributed in the bituminized matrix. The paper presents the experimental qualification of the method with real waste drums, showing a detection limit well below 1 kg of uranium in 20 min acquisitions while the usual gamma rays of 235 U (185 keV) or 238 U (1001 keV of 234m Pa in the radioactive decay chain) are not detected. The relative uncertainty on the uranium mass assessed by self-induced X-ray fluorescence (SXRF) is about 50%, with a 95% confidence level, taking into account the correction of photon attenuation in the waste matrix. This last indeed contains high atomic numbers elements like uranium, but also barium, in quantities which are not known for each drum. Attenuation is estimated thanks to the peak-to-Compton ratio to limit the corresponding uncertainty. The SXRF uranium masses measured in the real drums are in good agreement with long gamma-ray spectroscopy measurements (1001 keV peak) or with radiochemical analyses. (authors)

Oxidation behaviour of noble-metal inclusions in used UO2 nuclear fuel

International Nuclear Information System (INIS)

McEachern, R.

1997-07-01

The literature on the chemistry of the noble-metal (Mo-Rh-Ru-Pd-Tc) inclusions found in used nuclear fuel has been reviewed. The Mo-Ru-Pd phase diagram is reasonably well understood, and the pseudoternary Mo-(Tc+Ru)-Rh+Pd) system can be used to qualitatively understand the phase chemistry of the noble-metal inclusions. The kinetics of the oxidation reaction are not particularly well understood, but they are of limited applicability to understanding the properties of used fuel. In contrast, it is important to determine the thermodynamic activity of molybdenum in noble-metal inclusions, so that analysis of their molybdenum content can be used as a probe of the local oxygen potential of the used fuel. (author)

Development of detection techniques for the Swedish noble gas sampler

International Nuclear Information System (INIS)

Ringbom, A.

1998-11-01

A short review on the radioactive properties of noble gas isotopes relevant for monitoring of nuclear activities is given, together with a brief discussion of the existing systems for detection of radioactive noble gases. A 4π detection system to be used in the automatic version of the Swedish noble gas sampling device is described. Monte Carlo calculations of the total gamma and beta efficiency for different detector designs have been performed, together with estimates of the resulting minimum detectable concentration (MDC). The estimated MDC values for detection of the 133g Xe 81 keV and the 135g Xe 250 keV gamma lines are around 0.3 mBq/m 3 in both cases. This is a factor of three lower than the detection limit required for a sampling station in the Comprehensive Nuclear-Test-Ban Treaty monitoring network. The possibility to modify the system to detect 85 Kr is also discussed

Development of detection techniques for the Swedish noble gas sampler

Energy Technology Data Exchange (ETDEWEB)

Ringbom, A

1998-11-01

A short review on the radioactive properties of noble gas isotopes relevant for monitoring of nuclear activities is given, together with a brief discussion of the existing systems for detection of radioactive noble gases. A 4{pi} detection system to be used in the automatic version of the Swedish noble gas sampling device is described. Monte Carlo calculations of the total gamma and beta efficiency for different detector designs have been performed, together with estimates of the resulting minimum detectable concentration (MDC). The estimated MDC values for detection of the {sup 133g}Xe 81 keV and the {sup 135g}Xe 250 keV gamma lines are around 0.3 mBq/m{sup 3} in both cases. This is a factor of three lower than the detection limit required for a sampling station in the Comprehensive Nuclear-Test-Ban Treaty monitoring network. The possibility to modify the system to detect {sup 85}Kr is also discussed 27 refs, 13 figs, 3 tabs

Design of benign matrix drums for the non-destructive assay performance demonstration program for the National TRU Program

International Nuclear Information System (INIS)

Becker, G.K.

1996-09-01

Regulatory compliance programs associated with the Department of Energy (DOE) Waste Isolation Pilot Plant (WIPP) Transuranic (TRU) Waste Characterization Program (the Program) require the collection of waste characterization data of known quality to support repository performance assessment, permitting, and associated activities. Blind audit samples, referred to as PDP (performance demonstration program) samples, are devices used in the NDA PDP program to acquire waste NDA system performance data per defined measurement routines. As defined under the current NDA PDP Program Plan, a PDP sample consists of a DOT 17C 55-gallon PDP matrix drum configured with insertable radioactive standards, working reference materials (WRMs). The particular manner in which the matrix drum and PDP standard(s) are combined is a function of the waste NDA system performance test objectives of a given cycle. The scope of this document is confined to the design of the PDP drum radioactive standard internal support structure, the matrix type and the as installed configuration. The term benign is used to designate a matrix possessing properties which are nominally non-interfering to waste NDA measurement techniques. Measurement interference sources are technique specific but include attributes such as: high matrix density, heterogeneous matrix distributions, matrix compositions containing high moderator/high Z element concentrations, etc. To the extent practicable the matrix drum design should not unduly bias one NDA modality over another due to the manner in which the matrix drum configuration manifests itself to the measurement system. To this end the PDP matrix drum configuration and composition detailed below is driven primarily by the intent to minimize the incorporation of matrix attributes known to interfere with fundamental waste NDA modalities, i.e. neutron and gamma based techniques

The interpretation of ellipsometric measurements of ion bombardment of noble gases on semiconductor surfaces

NARCIS (Netherlands)

Holtslag, A.H.M.; Slager, U.C.; van Silfhout, Arend

1985-01-01

Low energy noble gas ion bombardment and thermal desorption studies were carried out on Si(111) and analysed, in situ, using spectroscopic ellipsometry. The amorphous layer thickness and implanted noble gas fraction were calculated.

Material Selection for a Manual Winch Rope Drum

OpenAIRE

Moses F. Oduori; Enoch K. Musyoka; Thomas O. Mbuya

2016-01-01

The selection of materials is an essential task in mechanical design processes. This paper sets out to demonstrate the application of analytical decision making during mechanical design and, particularly, in selecting a suitable material for a given application. Equations for the mechanical design of a manual winch rope drum are used to derive quantitative material performance indicators, which are then used in a multiple attribute decision making (MADM) model to rank the candidate materials....

The end of a noble narrative?

DEFF Research Database (Denmark)

Manners, Ian James; Murray, Philomena

2015-01-01

of the forerunner to the current EU we ask if this noble narrative of war and peace, which is at the heart of European integration, at an end. We argue that this principled account is likely to remain just one of several narratives of European integration, but with its reputation somewhat tarnished. Fresh...

Growth, reproduction, mortality, distribution, and biomass of freshwater drum in Lake Erie

Science.gov (United States)

Bur, Michael T.

1984-01-01

Predominant age-groups in the Lake Erie freshwater drum Aplodinotus grunnienspopulation were 3, 4, and 5 as determined from gill net, trap net, bottom trawl, and midwater trawl samples. Age and growth calculations indicated that females grew faster than males. However, the length-weight relation did not differ between sexes and was described by the equation: log W = −5.4383 + 3.1987 log L. Some males became sexually mature at age 2 and all were mature by age 6. Females matured 1 year later than males. Three sizes of eggs were present in ovaries; the average total number was 127,000 per female for 20 females over a length range of 270 to 478 mm. Seasonal analysis of the ovary-body weight ratio indicated that spawning extended from June to August. A total annual mortality rate of 49% for drum aged 4 through 11 was derived from catch-curve analysis. Freshwater drum were widely distributed throughout Lake Erie in 1977–1979, the greatest concentration being in the western basin. They moved into warm, shallow water (less than 10 m deep) during summer, and returned to deeper water in late fall. Summer biomass estimates for the western basin, based on systematic surveys with bottom trawls, were 9,545 t in 1977 and 2,333 t in 1978.

Microbial degradation of lignocellulosic fractions during drum composting of mixed organic waste

Directory of Open Access Journals (Sweden)

Vempalli Sudharsan Varma

2017-11-01

Full Text Available The study aimed to characterize the microbial population involved in lignocellulose degradation during drum composting of mixed organic waste i.e. vegetable waste, cattle manure, saw dust and dry leaves in a 550 L rotary drum composter. Lignocellulose degradation by different microbial populations was correlated by comparing results from four trials, i.e., Trial 1 (5:4, Trial 2 (6:3, Trial 3 (7:2 and Trial 4 (8:1 of varying waste combinations during 20 days of composting period. Due to proper combination of waste materials and agitation in drum composter, a maximum of 66.5 and 61.4 °C was achieved in Trial 1 and 2 by observing a temperature level of 55 °C for 4–6 d. The study revealed that combinations of waste materials had a major effect on the microbial degradation of waste material and quality of final compost due to its physical properties. However, Trial 1 was observed to have longer thermophilic phase leading to higher degradation of lignocellulosic fractions. Furthermore, Fourier transform infrared spectrometer and fluorescent spectroscopy confirmed the decrease in aliphatic to aromatic ratio and increase in polyphenolic compounds of the compost. Heterotrophic bacteria were observed predominantly due to the readily available organic matter during the initial period of composting. However, fungi and actinomycetes were active in the degradation of lignocellulosic fractions.

Appraisal of transport and deformation in shale reservoirs using natural noble gas tracers

Energy Technology Data Exchange (ETDEWEB)

Heath, Jason E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Kuhlman, Kristopher L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Robinson, David G. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Bauer, Stephen J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Gardner, William Payton [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Univ. of Montana, Missoula, MT (United States)

2015-09-01

This report presents efforts to develop the use of in situ naturally-occurring noble gas tracers to evaluate transport mechanisms and deformation in shale hydrocarbon reservoirs. Noble gases are promising as shale reservoir diagnostic tools due to their sensitivity of transport to: shale pore structure; phase partitioning between groundwater, liquid, and gaseous hydrocarbons; and deformation from hydraulic fracturing. Approximately 1.5-year time-series of wellhead fluid samples were collected from two hydraulically-fractured wells. The noble gas compositions and isotopes suggest a strong signature of atmospheric contribution to the noble gases that mix with deep, old reservoir fluids. Complex mixing and transport of fracturing fluid and reservoir fluids occurs during production. Real-time laboratory measurements were performed on triaxially-deforming shale samples to link deformation behavior, transport, and gas tracer signatures. Finally, we present improved methods for production forecasts that borrow statistical strength from production data of nearby wells to reduce uncertainty in the forecasts.

The desorption behaviour of implanted noble gases at low energy on silicon surfaces

NARCIS (Netherlands)

Holtslag, A.H.M.; van Silfhout, Arend

1987-01-01

Under UHV conditions, clean crystalline Si(111) surfaces have been bombarded mass-selectively at room temperature with noble gas ions, Ne+, Ar+, Kr+, at normal incidence. By means of stepwise heating up to 1050 K the activation energies and desorbed doses of the noble gases have been straight

Noble gas signatures in the Island of Maui, Hawaii: Characterizing groundwater sources in fractured systems

Science.gov (United States)

Niu, Yi; Castro, M. Clara; Hall, Chris M.; Gingerich, Stephen B.; Scholl, Martha A.; Warrier, Rohit B.

2017-01-01

Uneven distribution of rainfall and freshwater scarcity in populated areas in the Island of Maui, Hawaii, renders water resources management a challenge in this complex and ill-defined hydrological system. A previous study in the Galapagos Islands suggests that noble gas temperatures (NGTs) record seasonality in that fractured, rapid infiltration groundwater system rather than the commonly observed mean annual air temperature (MAAT) in sedimentary systems where infiltration is slower thus, providing information on recharge sources and potential flow paths. Here we report noble gas results from the basal aquifer, springs, and rainwater in Maui to explore the potential for noble gases in characterizing this type of complex fractured hydrologic systems. Most samples display a mass-dependent depletion pattern with respect to surface conditions consistent with previous observations both in the Galapagos Islands and Michigan rainwater. Basal aquifer and rainwater noble gas patterns are similar and suggest direct, fast recharge from precipitation to the basal aquifer. In contrast, multiple springs, representative of perched aquifers, display highly variable noble gas concentrations suggesting recharge from a variety of sources. The distinct noble gas patterns for the basal aquifer and springs suggest that basal and perched aquifers are separate entities. Maui rainwater displays high apparent NGTs, incompatible with surface conditions, pointing either to an origin at high altitudes with the presence of ice or an ice-like source of undetermined origin. Overall, noble gas signatures in Maui reflect the source of recharge rather than the expected altitude/temperature relationship commonly observed in sedimentary systems.

Noble gases as cardioprotectants - translatability and mechanism

NARCIS (Netherlands)

Smit, Kirsten F.; Weber, Nina C.; Hollmann, Markus W.; Preckel, Benedikt

2015-01-01

Several noble gases, although classified as inert substances, exert a tissue-protective effect in different experimental models when applied before organ ischaemia as an early or late preconditioning stimulus, after ischaemia as a post-conditioning stimulus or when given in combination before,

The crane handling system for 500 litre drums of cemented radioactive waste

International Nuclear Information System (INIS)

Staples, A.T.

1991-01-01

As part of the AEA Technology strategy for dealing with radioactive wastes new waste treatment facilities are being built at the Winfrith Technology Centre (WTC), Dorset. One of the facilities at WTC is the Treated Radwaste Store (TRS) which is designed to store sealed 500 litre capacity drums of treated waste for an interim period until the national disposal facility is operational. Within the TRS two cranes have been incorporated, one spanning the entire width and travelling the length of the Store. The second operates within the area designated for drum handling during inspection work. The development of the design of these cranes and their associated control systems, to meet the complex requirements of operations whilst also satisfying the reliability and safety criteria, is discussed within the paper. (author)

Test plan for a live drum survey using the gamma-neutron sensor

International Nuclear Information System (INIS)

Gehrke, R.J.; Roybal, L.G.; Thompson, D.N.

1995-07-01

This plan describes performance tests to be made with the Gamma/Neutron Sensor (GNS), which that was designed and built for infield assay at an excavation site. The performance tests will be performed in Building WMF-628 in the Transuranic Storage Area of the Radioactive Waste Management Complex at the Idaho National Engineering Laboratory on stored 55-gal drums of transuranic waste from the Rocky Flats Plant. The GNS is mounted on a wooden pallet that will allow horizontal and vertical scans of the stacked drums. Scanning speed and GNS sensitivity for gamma and neutron radiation fields will be estimated. Effects of temperature, electronic, and acoustic noise will be evaluated. Two- and three-dimensional plots of radiation field as a function of position will be developed from the data

49 CFR 178.509 - Standards for plastic drums and jerricans.

Science.gov (United States)

2010-10-01

... than production residues or regrind from the same manufacturing process may be used unless approved by... those used in the manufacture of the design type, retesting may be omitted if the carbon black content... or heads of drums and jerricans must be so designed and applied that they remain secure and leakproof...

Cucurbit[6]uril: A Possible Host for Noble Gas Atoms.

Science.gov (United States)

Pan, Sudip; Mandal, Subhajit; Chattaraj, Pratim K

2015-08-27

Density functional and ab initio molecular dynamics studies are carried out to investigate the stability of noble gas encapsulated cucurbit[6]uril (CB[6]) systems. Interaction energy, dissociation energy and dissociation enthalpy are calculated to understand the efficacy of CB[6] in encapsulating noble gas atoms. CB[6] could encapsulate up to three Ne atoms having dissociation energy (zero-point energy corrected) in the range of 3.4-4.1 kcal/mol, whereas due to larger size, only one Ar or Kr atom encapsulated analogues would be viable. The dissociation energy value for the second Ar atom is only 1.0 kcal/mol. On the other hand, the same for the second Kr is -0.5 kcal/mol, implying the instability of the system. The noble gas dissociation processes are endothermic in nature, which increases gradually along Ne to Kr. Kr encapsulated analogue is found to be viable at room temperature. However, low temperature is needed for Ne and Ar encapsulated analogues. The temperature-pressure phase diagram highlights the region in which association and dissociation processes of Kr@CB[6] would be favorable. At ambient temperature and pressure, CB[6] may be used as an effective noble gas carrier. Wiberg bond indices, noncovalent interaction indices, electron density, and energy decomposition analyses are used to explore the nature of interaction between noble gas atoms and CB[6]. Dispersion interaction is found to be the most important term in the attraction energy. Ne and Ar atoms in one Ng entrapped analogue are found to stay inside the cavity of CB[6] throughout the simulation at 298 K. However, during simulation Ng2 units in Ng2@CB[6] flip toward the open faces of CB[6]. After 1 ps, one Ne atom of Ne3@CB[6] almost reaches the open face keeping other two Ne atoms inside. At lower temperature (77 K), all the Ng atoms in Ngn@CB[6] remain well inside the cavity of CB[6] throughout the simulation time (1 ps).

Noble gas encapsulation into carbon nanotubes: Predictions from analytical model and DFT studies

Energy Technology Data Exchange (ETDEWEB)

Balasubramani, Sree Ganesh; Singh, Devendra; Swathi, R. S., E-mail: swathi@iisertvm.ac.in [School of Chemistry, Indian Institute of Science Education and Research Thiruvananthapuram (IISER-TVM), Kerala 695016 (India)

2014-11-14

The energetics for the interaction of the noble gas atoms with the carbon nanotubes (CNTs) are investigated using an analytical model and density functional theory calculations. Encapsulation of the noble gas atoms, He, Ne, Ar, Kr, and Xe into CNTs of various chiralities is studied in detail using an analytical model, developed earlier by Hill and co-workers. The constrained motion of the noble gas atoms along the axes of the CNTs as well as the off-axis motion are discussed. Analyses of the forces, interaction energies, acceptance and suction energies for the encapsulation enable us to predict the optimal CNTs that can encapsulate each of the noble gas atoms. We find that CNTs of radii 2.98 − 4.20 Å (chiral indices, (5,4), (6,4), (9,1), (6,6), and (9,3)) can efficiently encapsulate the He, Ne, Ar, Kr, and Xe atoms, respectively. Endohedral adsorption of all the noble gas atoms is preferred over exohedral adsorption on various CNTs. The results obtained using the analytical model are subsequently compared with the calculations performed with the dispersion-including density functional theory at the M06 − 2X level using a triple-zeta basis set and good qualitative agreement is found. The analytical model is however found to be computationally cheap as the equations can be numerically programmed and the results obtained in comparatively very less time.

Design and construction of a 208-L drum containing representative LLNL transuranic and low-level wastes

International Nuclear Information System (INIS)

Camp, D.C.; Pickering, J.; Martz, H.E.

1994-01-01

At the Lawrence Livermore National Laboratory (LLNL), we are developing the nondestructive analysis (NDA) technique of active (A) computed tomography (CT) to measure waste matrix attenuation as a function of gamma-ray energy (ACT); and passive. (P) Cr to locate and identify all gamma-ray emitting isotopes within a waste container. Coupling the ACT and PCT results will quantify each isotope identified, thereby categorize the amount of radioactivity within waste drums having volumes up to 416-liters (L), i.e., 110-gallon drums

Trauma team activation: Not just for trauma patients

Directory of Open Access Journals (Sweden)

Phoenix Vuong

2017-01-01

Full Text Available Specialized trauma teams have been shown to improve outcomes in critically injured patients. At our institution, an the American College of Surgeons Committee on trauma level I Trauma center, the trauma team activation (TTA criteria includes both physiologic and anatomic criteria, but any attending physician can activate the trauma team at their discretion outside criteria. As a result, the trauma team has been activated for noninjured patients meeting physiologic criteria secondary to nontraumatic hemorrhage. We present two cases in which the trauma team was activated for noninjured patients in hemorrhagic shock. The utilization of the TTA protocol and subsequent management by the trauma team are reviewed as we believe these were critical factors in the successful recovery of both patients. Beyond the primary improved survival outcomes of severely injured patients, trauma center designation has a “halo effect” that encompasses patients with nontraumatic hemorrhage.

Noble Metal/Ceramic Composites in Flame Processes

DEFF Research Database (Denmark)

Schultz, Heiko; Madler, Lutz; Strobel, Reto

conditions influence the resulting noble metal particles size in those systems [1]. For every specific application the particle size and the metal/metal oxide interaction affect the performance of these nano-composite materials [2]. Recently, aerosol processes have been successfully used to produce platinum...

Imaging with SiPMs in noble-gas detectors

International Nuclear Information System (INIS)

Yahlali, N; González, K; Fernandes, L M P; Garcia, A N C; Soriano, A

2013-01-01

Silicon photomultipliers (SiPMs) are photosensors widely used for imaging in a variety of high energy and nuclear physics experiments. In noble-gas detectors for double-beta decay and dark matter experiments, SiPMs are attractive photosensors for imaging. However they are insensitive to the VUV scintillation emitted by the noble gases (xenon and argon). This difficulty is overcome in the NEXT experiment by coating the SiPMs with tetraphenyl butadiene (TPB) to convert the VUV light into visible light. TPB requires stringent storage and operational conditions to prevent its degradation by environmental agents. The development of UV sensitive SiPMs is thus of utmost interest for experiments using electroluminescence of noble-gas detectors. It is in particular an important issue for a robust and background free ββ0ν experiment with xenon gas aimed by NEXT. The photon detection efficiency (PDE) of UV-enhanced SiPMs provided by Hamamatsu was determined for light in the range 250–500 nm. The PDE of standard SiPMs of the same model (S10362-33-50C), coated and non-coated with TPB, was also determined for comparison. In the UV range 250–350 nm, the PDE of the standard SiPM is shown to decrease strongly, down to about 3%. The UV-enhanced SiPM without window is shown to have the maximum PDE of 44% at 325 nm and 30% at 250 nm. The PDE of the UV-enhanced SiPM with silicon resin window has a similar trend in the UV range, although it is about 30% lower. The TPB-coated SiPM has shown to have about 6 times higher PDE than the non-coated SiPM in the range 250–315 nm. This is however below the performance of the UV-enhanced prototypes in the same wavelength range. Imaging in noble-gas detectors using UV-enhanced SiPMs is discussed.

NOBLE METAL CHEMISTRY AND HYDROGEN GENERATION DURING SIMULATED DWPF MELTER FEED PREPARATION

Energy Technology Data Exchange (ETDEWEB)

Koopman, D

2008-06-25

Simulations of the Defense Waste Processing Facility (DWPF) Chemical Processing Cell vessels were performed with the primary purpose of producing melter feeds for the beaded frit program plus obtaining samples of simulated slurries containing high concentrations of noble metals for off-site analytical studies for the hydrogen program. Eight pairs of 22-L simulations were performed of the Sludge Receipt and Adjustment Tank (SRAT) and Slurry Mix Evaporator (SME) cycles. These sixteen simulations did not contain mercury. Six pairs were trimmed with a single noble metal (Ag, Pd, Rh, or Ru). One pair had all four noble metals, and one pair had no noble metals. One supporting 4-L simulation was completed with Ru and Hg. Several other 4-L supporting tests with mercury have not yet been performed. This report covers the calculations performed on SRNL analytical and process data related to the noble metals and hydrogen generation. It was originally envisioned as a supporting document for the off-site analytical studies. Significant new findings were made, and many previous hypotheses and findings were given additional support as summarized below. The timing of hydrogen generation events was reproduced very well within each of the eight pairs of runs, e.g. the onset of hydrogen, peak in hydrogen, etc. occurred at nearly identical times. Peak generation rates and total SRAT masses of CO{sub 2} and oxides of nitrogen were reproduced well. Comparable measures for hydrogen were reproduced with more variability, but still reasonably well. The extent of the reproducibility of the results validates the conclusions that were drawn from the data.

Intelligent Mobile Sensor System for drum inspection and monitoring - Volume 1. Final report, October 1, 1993 - April 22, 1995

International Nuclear Information System (INIS)

1995-01-01

The objective of the Intelligent Mobile Sensor System (IMSS) project is to develop an operational system for monitoring and inspection activities for waste storage facility operations at several DOE sites. Specifically, the product of this effort is a robotic device with enhanced intelligence and maneuverability capable of conducting routine inspection of stored waste drums. The device is capable of operating in the narrow free aisle space between rows of stacked drums. The system has an integrated sensor suite for problem-drum detection, and is linked to a site database both for inspection planning and for data correlation, updating, and report generation. The system is capable of departing on an assigned mission, collecting required data, recording which portions of its mission had to be aborted or modified due to environmental constraints, and reporting back when the mission is complete. Successful identification of more than 96% of drum defects has been demonstrated in a high fidelity waste storage facility mockup. Identified anomalies included rust spots, rust streaks, areas of corrosion, dents, and tilted drums. All drums were positively identified and correlated with the site database. This development effort is separated into three phases of which phase two is now complete. The first phase demonstrated an integrated system (maturity level IVa) for monitoring and inspection activities for waste storage facility operations. The second phase demonstrated a prototype system appropriate for operational use in an actual storage facility. The prototype provides an integrated design that considers operational requirements, hardware costs, maintenance, safety, and robustness. The final phase will demonstrate commercial viability using the prototype vehicle in a pilot waste operations and inspection project. This report summarizes the design and evaluation of the new IMSS Phase 2 system and vehicle

Developmental and Metabolic Plasticity of White-Skinned Grape Berries in Response to Botrytis cinerea during Noble Rot1[OPEN

Science.gov (United States)

Collins, Thomas S.; Vicente, Ariel R.; Doyle, Carolyn L.; Ye, Zirou; Allen, Greg; Heymann, Hildegarde

2015-01-01

Noble rot results from exceptional infections of ripe grape (Vitis vinifera) berries by Botrytis cinerea. Unlike bunch rot, noble rot promotes favorable changes in grape berries and the accumulation of secondary metabolites that enhance wine grape composition. Noble rot-infected berries of cv Sémillon, a white-skinned variety, were collected over 3 years from a commercial vineyard at the same time that fruit were harvested for botrytized wine production. Using an integrated transcriptomics and metabolomics approach, we demonstrate that noble rot alters the metabolism of cv Sémillon berries by inducing biotic and abiotic stress responses as well as ripening processes. During noble rot, B. cinerea induced the expression of key regulators of ripening-associated pathways, some of which are distinctive to the normal ripening of red-skinned cultivars. Enhancement of phenylpropanoid metabolism, characterized by a restricted flux in white-skinned berries, was a common outcome of noble rot and red-skinned berry ripening. Transcript and metabolite analyses together with enzymatic assays determined that the biosynthesis of anthocyanins is a consistent hallmark of noble rot in cv Sémillon berries. The biosynthesis of terpenes and fatty acid aroma precursors also increased during noble rot. We finally characterized the impact of noble rot in botrytized wines. Altogether, the results of this work demonstrated that noble rot causes a major reprogramming of berry development and metabolism. This desirable interaction between a fruit and a fungus stimulates pathways otherwise inactive in white-skinned berries, leading to a greater accumulation of compounds involved in the unique flavor and aroma of botrytized wines. PMID:26450706

Validation testing of radioactive waste drum filter vents

Energy Technology Data Exchange (ETDEWEB)

Weber, L.D. [Pall Corp., Port Washington, NY (United States); Rahimi, R.S. [Pall Corp., Cortland, NY (United States); Edling, D. [Edling & Associates, Inc., Russel Springs, KY (United States)

1997-08-01

The minimum requirements for Drum Filter Vents (DFVs) can be met by demonstrating conformance with the Waste Isolation Pilot Plant (WIPP) Trupact II Safety Assessment Report (SAR), and conformance with U.S. Federal shipping regulations 49 CFR 178.350, DOT Spec 7A, for Type A packages. These together address a number of safety related performance parameters such as hydrogen diffusivity, flow related pressure drop, filtration efficiency and, separately, mechanical stability and the ability to prevent liquid water in-leakage. In order to make all metal DFV technology (including metallic filter medium) available to DOE sites, Pall launched a product development program to validate an all metal design to meet these requirements. Numerous problems experienced by DOE sites in the past came to light during this development program. They led us to explore enhancements to DFV design and performance testing addressing these difficulties and concerns. The result is a patented all metal DFV certified to all applicable regulatory requirements, which for the first time solves operational and health safety problems reported by DOE site personnel but not addressed by previous DFV`s. The new technology facilitates operations (such as manual, automated and semi-automated drum handling/redrumming), sampling, on-site storage, and shipping. At the same time, it upgrades filtration efficiency in configurations documented to maintain filter efficiency following mechanical stress. 2 refs., 2 figs., 10 tabs.

Christian Values and Noble Ideas of Rank and their Consequences on Symbolic Acts

Directory of Open Access Journals (Sweden)

Gerd ALTHOFF

2007-12-01

Full Text Available In the Middle Ages a Christian system of values met the values of a noble warrior society. Although these two systems had completely different conceptions of norms, they adapted from each other certain values and symbolic forms to express these values.The development of this adaptation is depicted by treating the Christian values misericordia, humilitas and clementia. In which way did the noble warrior society take up these values and how did these norms possibly change?Misericordia, for example, became an essential part of noble behaviour, but the fundamental idea of Christian misericordia was changed. Helping the poor was often motivated by the nobles’ will to prove his mercy, not by personal compassion.Although the value of humilitas implied a sharp contrast to the values of honor and rank, one can find forms of expression, which revealed a noble’s or ruler’s humility. With his humble behaviour one proved one’s qualification and legitimacy. Humility was expressed with symbolic forms of expression like walking barefoot and in penitential clothes or making footfalls. Similarly, these forms were used in inner-secular communication to acknowledge the existing order of rank.The ritual of deditio combines the values humilitas and clementia. The author describes this ritual as a pre-arranged stage-play, in which the one’s humility granted the other’s clemency. These ‘stage-plays’ had only little in common with the original Christian virtues, but this way several elements of the Christian virtue system influenced the noble behaviour pattern.En la edad media el sistema de valores cristiano confluye con el de una sociedad noble guerrera. Aunque ambos sistemas tuvieron dos concepciones de normas completamente diferentes, sin embargo, cada uno de ellos adapto ciertos valores y sus expresiones simbólicas del otro.El desarrollo de esta adaptación es descrito a través de los valores cristianos de misericordia, humilitas y clementia �

Safety evaluation for packaging (onsite) for the concrete-shielded RH TRU drum for the 327 Postirradiation Testing Laboratory

International Nuclear Information System (INIS)

Smith, R.J.

1998-01-01

This safety evaluation for packaging authorizes onsite transport of Type B quantities of radioactive material in the Concrete Shielded Remote-Handled Transuranic Waste (RH TRU) Drum per HNF-PRO-154, Responsibilities and Procedures for all Hazardous Material Shipments. The drum will be used for transport of 327 Building legacy waste from the 300 Area to a solid waste storage facility on the Hanford Site

Organ protection by the noble gas helium

NARCIS (Netherlands)

Smit, K.F.

2017-01-01

The aims of this thesis were to investigate whether helium induces preconditioning in humans, and to elucidate the mechanisms behind this possible protection. First, we collected data regarding organ protective effects of noble gases in general, and of helium in particular (chapters 1-3). In chapter

The efficacy of noble metal alloy urinary catheters in reducing catheter-associated urinary tract infection

Directory of Open Access Journals (Sweden)

Alanood Ahmed Aljohi

2016-01-01

Results: A 90% relative risk reduction in the rate of CAUTI was observed with the noble metal alloy catheter compared to the standard catheter (10 vs. 1 cases, P = 0.006. When considering both catheter-associated asymptomatic bacteriuria and CAUTI, the relative risk reduction was 83% (12 vs. 2 cases, P = 0.005. In addition to CAUTI, the risk of acquiring secondary bacteremia was lower (100% for the patients using noble metal alloy catheters (3 cases in the standard group vs. 0 case in the noble metal alloy catheter group, P = 0.24. No adverse events related to any of the used catheters were recorded. Conclusion: Results from this study revealed that noble metal alloy catheters are safe to use and significantly reduce CAUTI rate in ICU patients after 3 days of use.

Development of a method for determining the location of heterogeneous activity present in 200 litre waste drum using USB based MCS system

International Nuclear Information System (INIS)

Singh, Sarbjit; Mhatre, Amol; Sagar, Veena; Gupta, Nidhi

2014-01-01

A method was developed for determining the location of activity present in 200 litre waste drum using USB based MCS system coupled to a segmented gamma ray scanner. 137 Cs source was kept at various distances from centre of the drum along the axis of the detector. Drum was rotated and the activity profiles were determined as a function of angle of rotation. The plot of the count rate as a function of angle of rotation was found to have two peaks. The experimental and calculated data were found to match well at all angles. Present studies have shown that the ratio of height and width of the profile at angles of 0 ° and 180° can be used to determine the location of the activity in the drum. (author)

Trauma Tactics: Rethinking Trauma Education for Professional Nurses.

Science.gov (United States)

Garvey, Paula; Liddil, Jessica; Eley, Scott; Winfield, Scott

2016-01-01

According to the National Trauma Institute (2015), trauma accounts for more than 180,000 deaths each year in the United States. Nurses play a significant role in the care of trauma patients and therefore need appropriate education and training (L. ). Although several courses exist for trauma education, many nurses have not received adequate education in trauma management (B. ; L. ). Trauma Tactics, a 2-day course that focuses on high-fidelity human patient simulation, was created to meet this educational need. This descriptive study was conducted retrospectively to assess the effectiveness of the Trauma Tactics course. Pre- and postsurveys, tests, and simulation performance were used to evaluate professional nurses who participated in Trauma Tactics over a 10-month period. Fifty-five nurses were included in the study. Pre- and postsurveys revealed an increase in overall confidence, test scores increased by an average of 2.5 points, and simulation performance scores increased by an average of 16 points. Trauma Tactics is a high-quality course that provides a valuable and impactful educational experience for nurses. Further research is needed to evaluate the long-term effects of Trauma Tactics and its impacts on quality of care and patient outcomes.

Natural Death and the Noble Savage.

Science.gov (United States)

Walter, Tony

1995-01-01

The belief that dying and grieving are natural processes is widely held in modern bereavement care. Examines four assumption often made in this connection: (1) most primitive cultures deal with death in an accepting way; (2) this way is different than our own; (3) it is a good and noble way; and (4) traditional societies see death as natural. (JBJ)

A mathematical model of steam-drum dynamics

International Nuclear Information System (INIS)

Moeck, E.O.; Hinds, H.W.

1976-12-01

Mathematical equations describing the dynamic behaviour of pressure, water mass, etc. in a steam drum are derived from basic principles. The resultant model includes such effects as steam superheating and water subcooling as well as spontaneous flashing of liquid and condensation of vapour. Experimental data from a pressurizer are adequately predicted by the model. The pressure rise following a turbine trip can be predicted by the isentropic-compression model but not by the thermodynamic-equilibrium model. The equations are individually linearized and implemented on an analog computer in such a way that their non-linear behaviour is retained for small-perturbation studies. (author)

Swing Once More: Relating Timing and Tempo in Expert Jazz Drumming

NARCIS (Netherlands)

Honing, H.; de Haas, W.B.|info:eu-repo/dai/nl/304841250

2008-01-01

Swing refers to a characteristic long-short subdivision of the beat that is generally considered a crucial aspect that contributes to the quality of a jazz or pop performance. The current study measures this pattern (referred to as the ‘swing ratio’) at different tempi in jazz drumming. The

Swing once more: Relating timing and tempo in expert jazz drumming

NARCIS (Netherlands)

Honing, H.; de Haas, W.B.

2008-01-01

Swing refers to a characteristic long-short subdivision of the beat that is generally considered a crucial aspect that contributes to the quality of a jazz or pop performance. The current study measures this pattern (referred to as the 'swing ratio') at different tempi in jazz drumming. The

Safety evaluation for packaging (onsite) for concrete-shielded RHTRU waste drum for the 327 postirradiation testing laboratory

Energy Technology Data Exchange (ETDEWEB)

Adkins, H.E.

1996-10-29

This safety evaluation for packaging authorizes onsite transport of Type B quantities of radioactive material in the Concrete- Shielded Remote-Handled Transuranic Waste (RH TRU) Drum per WHC-CM-2-14, Hazardous Material Packaging and Shipping. The drum will be used for transport of 327 Building legacy waste from the 300 Area to the Transuranic Waste Storage and Assay Facility in the 200 West Area and on to a Solid Waste Storage Facility, also in the 200 Area.

Selective noble gases monitoring

International Nuclear Information System (INIS)

Janecka, S.; Jancik, O.; Kapisovsky, V.; Kubik, I.; Sevecka, S.

1995-01-01

The monitoring of leak releases from ventilation stack of NPP requires a system by several orders more sensitive then currently used radiometer Kalina, designed to cover the range up to a design-based accident. To reach this goal a noble gases monitor with a germanium detector (MPVG) has been developed. It enables nuclide selective monitoring of current value of volume activity of particular nuclides in ventilation stack and daily releases of noble gases (balancing). MPVG can be viewed as a system build of three levels of subsystem: measuring level; control level; presentation level. Measuring level consists of gamma-spectroscopy system and operational parameters monitoring unit (flow rate, temperature, humidity). Control level provides communication between presentation and measuring level, acquisition of operational parameters and power supply. The presentation level of MPVG enables: 1) the measured data storage in predetermined time intervals; 2) the presentation of measured and evaluated values of radiation characteristics. The monitored radionuclides - default set: argon-41, krypton-85m, krypton-87, krypton-88, krypton-89, xenon-131m, xenon-133, xenon-133m, xenon-135, xenon-135m, xenon-137 and xenon-138. The values of volume activities observed at maximum releases have been approximately ten times higher. In that case in balancing some other nuclides exceed corresponding detection limits: 88 Kr(67; 22) Bq/m 3 ; 85m Kr(17; 7) Bq/m 3 ; 135m Xe(7.1; 0.5) Bq/m 3 ; 138 Xe(5.9; 0.9) Bq/m 3 . (J.K.)

Selective noble gases monitoring

Energy Technology Data Exchange (ETDEWEB)

Janecka, S; Jancik, O; Kapisovsky, V; Kubik, I; Sevecka, S [Nuclear Power Plants Research Institute, a.s., Trnava (Slovakia)

1996-12-31

The monitoring of leak releases from ventilation stack of NPP requires a system by several orders more sensitive then currently used radiometer Kalina, designed to cover the range up to a design-based accident. To reach this goal a noble gases monitor with a germanium detector (MPVG) has been developed. It enables nuclide selective monitoring of current value of volume activity of particular nuclides in ventilation stack and daily releases of noble gases (balancing). MPVG can be viewed as a system build of three levels of subsystem: measuring level; control level; presentation level. Measuring level consists of gamma-spectroscopy system and operational parameters monitoring unit (flow rate, temperature, humidity). Control level provides communication between presentation and measuring level, acquisition of operational parameters and power supply. The presentation level of MPVG enables: 1) the measured data storage in predetermined time intervals; 2) the presentation of measured and evaluated values of radiation characteristics. The monitored radionuclides - default set: argon-41, krypton-85m, krypton-87, krypton-88, krypton-89, xenon-131m, xenon-133, xenon-133m, xenon-135, xenon-135m, xenon-137 and xenon-138. The values of volume activities observed at maximum releases have been approximately ten times higher. In that case in balancing some other nuclides exceed corresponding detection limits: {sup 88}Kr(67; 22) Bq/m{sup 3}; {sup 85m}Kr(17; 7) Bq/m{sup 3}; {sup 135m}Xe(7.1; 0.5) Bq/m{sup 3}; {sup 138}Xe(5.9; 0.9) Bq/m{sup 3}. (J.K.).

Intelligent mobile sensor system for drum inspection and monitoring: Topical report, October 1, 1993--April 22, 1995

International Nuclear Information System (INIS)

1997-01-01

The objective of the Intelligent Mobile Sensor System (IMSS) project is to develop an operational system for monitoring and inspection activities for waste storage facility operations at several DOE sites. Specifically, the product of this effort is a robotic device with enhanced intelligence and maneuverability capable of conducting routine inspection of stored waste drums. The system has an integrated sensor suite for problem-drum detection, and is linked to a site database both for inspection planning and for data correlation, updating, and report generation. The system is capable of departing on an assigned mission, collecting required data, recording which portions of its mission had to be aborted or modified due to environmental constraints, and reporting back when the mission is complete. Successful identification of more than 96% of drum defects has been demonstrated in a high fidelity waste storage facility mockup. Identified anomalies included rust spots, rust streaks, areas of corrosion, dents, and tilted drums. All drums were positively identified and correlated with the site database. This development effort is separated into three phases of which phase two is now complete. The second phase demonstrated a prototype system appropriate for operational use in an actual storage facility. The prototype provides an integrated design that considers operational requirements, hardware costs, maintenance, safety, and robustness. The final phase will demonstrate commercial viability using the prototype vehicle in a pilot waste operations and inspection project. This report summarizes the design and evaluation of the new IMSS Phase 2 system and vehicle. Several parts of the IMSS Phase 1 Topical (Final) Report, which describes the requirements, design guidelines, and detailed design of the Phase 1 IMSS vehicle, are incorporated here, with modifications to reflect the changes in the design and the new elements added during the Phase 2 work

Effects of halogens on interactions between a reduced TiO{sub 2} (110) surface and noble metal atoms: A DFT study

Energy Technology Data Exchange (ETDEWEB)

Tada, Kohei, E-mail: k-tada@aist.go.jp [Department of Chemistry, Graduate School of Science, Osaka University, 1-1, Machikaneyama, Toyonaka, Osaka, 560-0043 (Japan); Research Institute of Electrochemical Energy, National Institute of Advanced Industrial Science and Technology (AIST), 1-8-31, Midorigaoka, Ikeda, Osaka, 563-8577 (Japan); Koga, Hiroaki [Element Strategy Initiative for Catalysts and Batteries (ESICB), Kyoto University, 1-30 Goryo Ohara, Nishikyo, Kyoto, 615-8245 (Japan); Hayashi, Akihide; Kondo, Yudai; Kawakami, Takashi; Yamanaka, Shusuke [Department of Chemistry, Graduate School of Science, Osaka University, 1-1, Machikaneyama, Toyonaka, Osaka, 560-0043 (Japan); Okumura, Mitsutaka [Department of Chemistry, Graduate School of Science, Osaka University, 1-1, Machikaneyama, Toyonaka, Osaka, 560-0043 (Japan); Element Strategy Initiative for Catalysts and Batteries (ESICB), Kyoto University, 1-30 Goryo Ohara, Nishikyo, Kyoto, 615-8245 (Japan)

2017-07-31

Highlights: • We investigated the halogen effect on the interactions of noble metals with TiO{sub 2}. • Halogen atoms inhibit electron transfer from TiO{sub 2} to noble metals. • Iodine stabilizes the adsorption of noble metals especially for Ag and Cu. • Electron transfer from the TiO{sub 2} is effective in anchoring Au and Pt atoms. • Covalent interaction with the support is effective in anchoring Ag and Cu atoms. - Abstract: Using DFT calculation, we investigate the effects of halogens on the interactions between rutile TiO{sub 2} (110) and noble metal atoms (Au, Ag, Cu, Pt, and Pd). Fluorine, chlorine, and bromine atoms occupy the oxygen defect sites of TiO{sub 2}, decreasing the stability of noble metal atoms on the surface. This decrease occurs because the halogens inhibit electron transfer from TiO{sub 2} to the noble metal atoms; the electron transfer from reduced TiO{sub 2} to the noble metal atom stabilizes the noble metal atom adsorption. In contrast, iodine strengthens the interactions between TiO{sub 2} and some noble metal atoms, namely Ag and Cu. This stabilization occurs because of the covalent interaction between iodine-doped TiO{sub 2} and the noble metal atom. Therefore, the stabilization is explained well by chemical hardness. This result suggests that iodine-doping of a TiO{sub 2} surface would be an effective method for the preparation of highly stabilized noble metal clusters.

Mantle Noble Gas Contents Controlled by Subduction of Serpentinite

Science.gov (United States)

Krantz, J. A.; Parman, S. W.; Kelley, S. P.; Smye, A.; Jackson, C.

2017-12-01

Geochemical analyses of exhumed subduction zone material1, well gases2, MORB, and OIBs3 indicate that noble gases are being recycled from the surface of the earth into the mantle. However, the path taken by these noble gases is unclear. To estimate the distribution and quantity of Ar, Kr, and Xe in subducting slabs, a model consisting of layers of sediments, altered oceanic crust (AOC), and serpentinite (hydrously altered mantle) has been developed. The noble gas contents of sediments and AOC were calculated using the least air-like and most gas-rich analyses from natural systems4,5, while serpentinite was modelled using both data from natural systems1 and experimentally determined solubilities. Layer thicknesses were assessed over a range of values: 1 to 12 km of sediments, 5 to 9 km of AOC, and 1 to 30 km of serpentinite. In all cases, the serpentinite layer contains at least an order of magnitude more Ar and Kr than the other layers. For realistic layer thicknesses (1 km of sediments, 6 km of AOC, and 3 km of serpentinite), Xe is distributed roughly equally between the three layers. By incorporating global subduction rates6, fluxes of the heavy noble gases into the mantle have been calculated as 4 · 1012 mol/Ma for 36Ar, 6 · 1011 mol/Ma for 84Kr, and 8 · 109 mol/Ma for 130Xe. These fluxes are equivalent to the total 84Kr and 130Xe contents of the depleted and bulk mantle over 1 and 10 Ma7. Similarly, the flux of 36Ar is equivalent over 1 and 100 Ma. Since the Kr and Xe have not been completely overprinted by recycling, the large majority of subducted noble gases must escape in the subduction zone. However, even the small amounts that are subducted deeper have affected the mantle as measured in both MORB and OIBs. 1. Kendrick, M.A. et al., Nature Geoscience, 4, 807-812, 2011 2. Holland, G. and Ballentine, C.J., Nature, 441, 186-191, 2006 3. Parai, R. and Mukhopadhyay, S., G3, 16, 719-735, 2015 4. Matsuda, J. and Nagao, K., Geochemical Journal, 20, 71-80, 1986

Solid polymer electrolyte composite membrane comprising a porous support and a solid polymer electrolyte including a dispersed reduced noble metal or noble metal oxide

Science.gov (United States)

Liu, Han; Mittelsteadt, Cortney K; Norman, Timothy J; Griffith, Arthur E; LaConti, Anthony B

2015-02-24

A solid polymer electrolyte composite membrane and method of manufacturing the same. According to one embodiment, the composite membrane comprises a thin, rigid, dimensionally-stable, non-electrically-conducting support, the support having a plurality of cylindrical, straight-through pores extending perpendicularly between opposing top and bottom surfaces of the support. The pores are unevenly distributed, with some or no pores located along the periphery and more pores located centrally. The pores are completely filled with a solid polymer electrolyte, the solid polymer electrolyte including a dispersed reduced noble metal or noble metal oxide. The solid polymer electrolyte may also be deposited over the top and/or bottom surfaces of the support.

Quarter-scale modeling of room convergence effects on CH [contact-handled] TRU drum waste emplacements using WIPP [Waste Isolation Pilot Plant] reference design geometries

International Nuclear Information System (INIS)

VandeKraats, J.

1987-11-01

This study investigates the effect of horizontal room convergence on CH waste packages emplaced in the WIPP Reference Design geometry (rooms 13 feet high by 33 feet wide, with minus 3/8 inch screened backfill emplaced over and around the waste packages) as a function of time. Based on two tests, predictions were made with regard to full-scale 6-packs emplaced in the Reference Design geometry. These are that load will be transmitted completely through the stack within the first five years after waste emplacement and all drums in all 6-packs will be affected; that virtually all drums will show some deformation eight years after emplacement; that some drums may breach before the eighth year after emplacement has elapsed; and that based on criteria developed during testing, it is predicted that 1% of the drums emplaced will be breached after 8 years and, after 15 years, approximately 12% of the drums are predicted to be breached. 8 refs., 41 figs., 3 tabs

Synthesis of Zeolite Materials for Noble Gas Separation

International Nuclear Information System (INIS)

Achey, R.; Rivera, O.; Wellons, M.; Hunter, D.

2017-01-01

Microporous zeolite adsorbent materials are widely used as a medium for separating gases. Adsorbent gas separation systems can run at ambient temperature and require minimal pressure to flow the input gas stream across the adsorbent bed. This allows for low energy consumption relative to other types of separation systems. Specific zeolites also have a high capacity and selectivity for the gases of interest, leading to compact and efficient separation systems. These characteristics are particularly advantageous for the application of signatures detection for non-proliferation, which often requires portable systems with low power draw. Savannah River National Laboratory currently is the leader in using zeolites for noble gas sampling for non-proliferation detection platforms. However, there is a constant customer need for improved sampling capabilities. Development of improved zeolite materials will lead to improved sampling technology. Microwave-assisted and conventional hydrothermal synthesis have been used to make a variety of zeolites tailored for noble gas separation. Materials characterization data collected in this project has been used to help guide the synthesis of improved zeolite materials. Candidate materials have been down-selected based on highest available surface area, maximum overall capacity for gas adsorption and highest selectivity. The creation of improved adsorbent materials initiated in this project will lead to development of more compact, efficient and effective noble gas collectors and concentrators. The work performed in this project will be used as a foundation for funding proposals for further material development as well as possible industrial applications.

Synthesis of Zeolite Materials for Noble Gas Separation

Energy Technology Data Exchange (ETDEWEB)

Achey, R. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Rivera, O. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Wellons, M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hunter, D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2017-10-02

Microporous zeolite adsorbent materials are widely used as a medium for separating gases. Adsorbent gas separation systems can run at ambient temperature and require minimal pressure to flow the input gas stream across the adsorbent bed. This allows for low energy consumption relative to other types of separation systems. Specific zeolites also have a high capacity and selectivity for the gases of interest, leading to compact and efficient separation systems. These characteristics are particularly advantageous for the application of signatures detection for non-proliferation, which often requires portable systems with low power draw. Savannah River National Laboratory currently is the leader in using zeolites for noble gas sampling for non-proliferation detection platforms. However, there is a constant customer need for improved sampling capabilities. Development of improved zeolite materials will lead to improved sampling technology. Microwave-assisted and conventional hydrothermal synthesis have been used to make a variety of zeolites tailored for noble gas separation. Materials characterization data collected in this project has been used to help guide the synthesis of improved zeolite materials. Candidate materials have been down-selected based on highest available surface area, maximum overall capacity for gas adsorption and highest selectivity. The creation of improved adsorbent materials initiated in this project will lead to development of more compact, efficient and effective noble gas collectors and concentrators. The work performed in this project will be used as a foundation for funding proposals for further material development as well as possible industrial applications.

Sampling and analysis plan for the characterization of eight drums at the 200-BP-5 pump-and-treat systems

International Nuclear Information System (INIS)

Laws, J.R.

1995-01-01

Samples will be collected and analyzed to provide sufficient information for characterization of mercury and aluminum contamination in drums from the final rinse of the tanks in the two pump-and-treat systems supporting the 200-BP-5 Operable Unit. The data will be used to determine the type of contamination in the drums to properly designate the waste for disposal or treatment. This sampling plan does not substitute the sampling requirements but is a separate sampling event to manage eight drums containing waste generated during an unanticipated contamination of the process water with mercury and aluminum nitrate nonahydrate (ANN). The Toxicity Characteristic Leaching Procedure (TCLP) will be used for extraction, and standard US Environmental Protection Agency (EPA) methods will be used for analysis

Current trauma care system and trauma care training in China

Directory of Open Access Journals (Sweden)

Lian-Yang Zhang

2018-04-01

Full Text Available Trauma is a life-threatening “modern disease”. The outcomes could only be optimized by cost-efficient and prompt trauma care, which embarks on the improvement of essential capacities and conceptual revolution in addition to the disruptive innovation of the trauma care system. According to experiences from the developed countries, systematic trauma care training is the cornerstone of the generalization and the improvement on the trauma care, such as the Advance Trauma Life Support (ATLS. Currently, the pre-hospital emergency medical services (EMS has been one of the essential elements of infrastructure of health services in China, which is also fundamental to the trauma care system. Hereby, the China Trauma Care Training (CTCT with independent intellectual property rights has been initiated and launched by the Chinese Trauma Surgeon Association to extend the up-to-date concepts and techniques in the field of trauma care as well to reinforce the generally well-accepted standardized protocols in the practices. This article reviews the current status of the trauma care system as well as the trauma care training. Keywords: Trauma care system, Trauma care training, China

Method to separate fission noble gases from gaseous wastes of a reprocessing plant for nuclear fuel material

International Nuclear Information System (INIS)

Schnez, H.

1977-01-01

In order to avoid the high cost expenditure in the separation of fission noble gases from waste gas of the head end, the following economical method is suggested: The fission noble gases released in the solvent - after grinding and burn-up of the nuclear fuel elements and dissolving in HNO 3 - are purified in a known method and collected in an equalizing tank. From here, the fission noble gas quantity necessary as washing gas is recycled into the solvent, so that a part of the fission noble gas quantity flows in a circuit. The quantity of fission noble gas not required for the above is separated from the circuit, compressed and put into a storage container from where it can be put into gas flashs or be recycled in the gas circuit where necessary. Furthermore, the method involves that to separate krypton, the filtered fission noble gas is compressed, cooled and rectified, whereby the krypton mixture taken from the rectification column is stored under high pressure and the gas part containing xenon, occuring as liquid, is at least partly fed back to the solvent. (HPH) [de

Preparation and Heat-Treatment of DWPF Simulants With and Without Co-Precipitated Noble Metals

International Nuclear Information System (INIS)

Koopman, David C.:Eibling, Russel E

2005-01-01

The Savannah River National Laboratory is in the process of investigating factors suspected of impacting catalytic hydrogen generation in the Chemical Process Cell of the Defense Waste Processing Facility, DWPF. Noble metal catalyzed hydrogen generation in simulation work constrains the allowable acid addition operating window in DWPF. This constraint potentially impacts washing strategies during sludge batch preparation. It can also influence decisions related to the addition of secondary waste streams to a sludge batch. Noble metals have historically been added as trim chemicals to process simulations. The present study investigated the potential conservatism that might be present from adding the catalytic species as trim chemicals to the final sludge simulant versus co-precipitating the noble metals into the insoluble sludge solids matrix. Parallel preparations of two sludge simulants targeting the composition of Sludge Batch 3 were performed in order to evaluate the impact of the form of noble metals. Identical steps were used except that one simulant had dissolved palladium, rhodium, and ruthenium present during the precipitation of the insoluble solids. Noble metals were trimmed into the other stimulant prior to process tests. Portions of both sludge simulants were held at 97 C for about eight hours to qualitatively simulate the effects of long term storage on particle morphology and speciation. The simulants were used as feeds for Sludge Receipt and Adjustment Tank, SRAT, process simulations. The following conclusions were drawn from the simulant preparation work: (1) The first preparation of a waste slurry simulant with co-precipitated noble metals was successful, based on the data obtained. It appears that 99+% of the noble metals were retained in the simulant. (2) Better control of carbonate, hydroxide, and post-wash trim chemical additions is needed before the new method of simulant preparation will be as reproducible as the old method. (3) The two new

Middle School Drum Ensemble: An Unlikely Experience in Classroom Democracy

Science.gov (United States)

Barbre, James

2013-01-01

Though music has a long and successful history within education, it is often one of the first sacrificial lambs when school budgets tighten. Over the course of an academic year, a documentary film sought to tell the story of an American middle school drum ensemble. The context of this group provided an ideal way to examine the nature of student…

Noble metal behavior during melting of simulated high-level nuclear waste glass feeds

International Nuclear Information System (INIS)

Anderson, L.D.; Dennis, T.; Elliott, M.L.; Hrma, P.

1994-01-01

Noble metals and their oxides can settle in waste glass melters and cause electrical shorting. Simulate waste feeds from Hanford, Savannah River, and Kernforschungszentrum Karlsruhe were heat treated for 1 hour in a gradient furnace at temperatures ranging from approximately 600 degrees C to 1000 degrees C and examined by electron microscopy to determine shapes, sizes, and distribution of noble metal particles as a function of temperature. Individual noble metal particles and agglomerates of rhodium (Rh), ruthenium (RuO 2 ), and palladium (Pd), as well as their alloys, were seen. The majority of particles and agglomerates were generally less than 10 μm; however, large agglomerations (up to 1 mm) were found in the German feed. 5 refs., 6 figs., 2 tabs

DEM simulation of particle mixing for optimizing the overcoating drum in HTR fuel fabrication

Science.gov (United States)

Liu, Malin; Lu, Zhengming; Liu, Bing; Shao, Youlin

2013-06-01

The rotating drum was used for overcoating coated fuel particles in HTR fuel fabrication process. All the coated particles should be adhered to equal amount of graphite powder, which means that the particle should be mixed quickly in both radial and axial directions. This paper investigated the particle flow dynamics and mixing behavior in different regimes using the discrete element method (DEM). By varying the rotation speed, different flow regimes such as slumping, rolling, cascading, cataracting, centrifuging were produced. The mixing entropy based on radial and axial grid was introduced to describe the radial and axial mixing behaviors. From simulation results, it was found that the radial mixing can be achieved in the cascading regime more quickly than the slumping, rolling and centrifuging regimes, but the traditional rotating drum without internal components can not achieve the requirements of axial mixing and should be improved. Three different structures of internal components are proposed and simulated. The new V-shaped deflectors were found to achieve a quick axial mixing behavior and uniform axial distribution in the rotating drum based on simulation results. At last, the superiority was validated by experimental results, and the new V-shaped deflectors were used in the industrial production of the overcoating coated fuel particles in HTR fuel fabrication process.

First Industrial Tests of a Matrix Monitor Correction for the Differential Die-away Technique of Historical Waste Drums

International Nuclear Information System (INIS)

Antoni, Rodolphe; Passard, Christian; Perot, Bertrand; Batifol, Marc; Vandamme, Jean-Christophe; Grassi, Gabriele

2015-01-01

The fissile mass in radioactive waste drums filled with compacted metallic residues (spent fuel hulls and nozzles) produced at AREVA NC La Hague reprocessing plant is measured by neutron interrogation with the Differential Die-away measurement Technique (DDT). In the next years, old hulls and nozzles mixed with Ion-Exchange Resins will be measured. The ion-exchange resins increase neutron moderation in the matrix, compared to the waste measured in the current process. In this context, the Nuclear Measurement Laboratory (LMN) of CEA Cadarache has studied a matrix effect correction method, based on a drum monitor, namely a 3He proportional counter located inside the measurement cavity. After feasibility studies performed with LMN's PROMETHEE 6 laboratory measurement cell and with MCNPX simulations, this paper presents first experimental tests performed on the industrial ACC (hulls and nozzles compaction facility) measurement system. A calculation vs. experiment benchmark has been carried out by performing dedicated calibration measurements with a representative drum and 235 U samples. The comparison between calculation and experiment shows a satisfactory agreement for the drum monitor. The final objective of this work is to confirm the reliability of the modeling approach and the industrial feasibility of the method, which will be implemented on the industrial station for the measurement of historical wastes. (authors)

Analysis of heat conduction in a drum brake system of the wheeled armored personnel carriers

Science.gov (United States)

Puncioiu, A. M.; Truta, M.; Vedinas, I.; Marinescu, M.; Vinturis, V.

2015-11-01

This paper is an integrated study performed over the Braking System of the Wheeled Armored Personnel Carriers. It mainly aims to analyze the heat transfer process which is present in almost any industrial and natural process. The vehicle drum brake systems can generate extremely high temperatures under high but short duration braking loads or under relatively light but continuous braking. For the proper conduct of the special vehicles mission in rough terrain, we are talking about, on one hand, the importance of the possibility of immobilization and retaining position and, on the other hand, during the braking process, the importance movement stability and reversibility or reversibility, to an encounter with an obstacle. Heat transfer processes influence the performance of the braking system. In the braking phase, kinetic energy transforms into thermal energy resulting in intense heating and high temperature states of analyzed vehicle wheels. In the present work a finite element model for the temperature distribution in a brake drum is developed, by employing commercial finite element software, ANSYS. These structural and thermal FEA models will simulate entire braking event. The heat generated during braking causes distortion which modifies thermoelastic contact pressure distribution drum-shoe interface. In order to capture the effect of heat, a transient thermal analysis is performed in order to predict the temperature distribution transitional brake components. Drum brakes are checked both mechanical and thermal. These tests aim to establish their sustainability in terms of wear and the variation coefficient of friction between the friction surfaces with increasing temperature. Modeling using simulation programs led eventually to the establishment of actual thermal load of the mechanism of brake components. It was drawn the efficiency characteristic by plotting the coefficient of effectiveness relative to the coefficient of friction shoe-drum. Thus induced

Simultaneous correction of attenuation and geometric response in emission tomography applied to nuclear waste drums

International Nuclear Information System (INIS)

Thierry, Raphael

1999-01-01

Multi-photonic emission tomography is a non destructive technique applied to the control of radioactive waste drums. The emitted gamma rays are detected on the range [50 keV, 2 MeV] by a hyper pure germanium, of high resolution in energy, which enables to set up a detailed list of radionuclides contained within the drum. From different points of measurement located in a transaxial plane of the drum, the activity distribution is computed by a reconstruction algorithm. An algebraic modelling of the physical process has been developed in order to correct the different degrading phenomenon, in particular the attenuation and the detector geometric response. Attenuation through the materials constituting the barrel is the preponderant phenomena. Its ignorance prevents from accurate activity quantification. Its correction has been realised from an attenuation map obtained by a transmission tomograph. The detector geometric response, introducing a blurring within the detection, is compensated by an analytic model. An adequate modelling of those phenomenon is primordial: it highly contributes on a large scale the image quality and the quantification. The image reconstruction, requiring the resolution of sparse linear system, is realised by iterative algorithms. Due to the 'ill-posed' nature of tomographic reconstruction, it is necessary to use regularisation: by introducing an a priori information on the solution, the stabilisation of the methods is carried out. We chose to minimise the Maximum A Posteriori criterion. Its resolution is considered with a half-quadratic regularisation: it permits the preservation of natural discontinuities, and avoids global-over smoothing of the image. It is evaluated on real phantoms and waste drums. Efficient sampling of the data is considered. (author) [fr

Polymer-noble metal nanocomposites: Review

CSIR Research Space (South Africa)

Folarin, OM

2011-09-01

Full Text Available because of their multi-functionality, ease of process-ability, potential for large-scale manufacturing, significantly lighter than metals, ease of synthesis when compared to the oxide/noble metal multi-layers (Gass et al., 2006; Lee et al., 2003.... their easy aggregation arising from their high surface free energy (Lee et al., 2006). In the design of nanocomposites, one must consider the properties of the polymer matrix as well as the stability of the nanoparticles and more importantly...

Techniques for the quantitative analysis of fission-product noble metals

International Nuclear Information System (INIS)

Lautensleger, A.W.; Hara, F.T.

1982-08-01

Analytical procedures for the determination of ruthenium, rhodium, and palladium in precursor waste, solvent metal, and final glass waste forms have been developed. Two procedures for the analysis of noble metals in the calcine and glass waste forms are described in this report. The first is a fast and simple technique that combines inductively coupled argon plasma atomic emission spectrometry (ICP) and x-ray fluorescence techniques and can only be used on nonradioactive materials. The second procedure is based on a noble metal separation step, followed by an analysis using ICP. This second method is more complicated than the first, but it will work on radioactive materials. Also described is a procedure for the ICP analysis of noble metals in the solvent metal matrix. The only solvent metal addressed in this procedure is lead, but with minor changes the procedure could be applied to any of the solvent metals being considered in the Pacific Northwest Laboratory (PNL) extraction process. A brief explanation of atomic spectroscopy and the ICP analytical process, as well as of certain aspects of ICP performance (interelement spectral line interferences and certain matrix effects) is given

Corrosion susceptibility of steel drums to be used as containers for intermediate level nuclear waste

Science.gov (United States)

Farina, S.; Schulz Rodriguez, F.; Duffó, G.

2013-07-01

The present work is a study of the corrosion susceptibility of steel drums in contact with cemented ion-exchange resins contaminated with different types and concentrations of aggressive species. A special type of specimen was manufactured to simulate the cemented ion-exchange resins in the drum. The evolution of the corrosion potential and the corrosion rate of the steel, as well as the electrical resistivity of the matrix were monitored over a time period of 900 days. The aggressive species studied were chloride ions (the main ionic species of concern) and sulphate ions (produced during radiolysis of the cationic exchange-resins after cementation). The work was complemented with an analysis of the corrosion products formed on the steel in each condition, as well as the morphology of the corrosion products. When applying the results obtained in the present work to estimate the corrosion depth of the steel drumscontaining the cemented radioactive waste after a period of 300 years (foreseen durability of the Intermediate Level Radioactive Waste facility in Argentina) , it is found that in the most unfavourable case (high chloride contamination), the corrosion penetration will be considerably lower than the thickness of the wall of the steel drums.

Electrospun Polymer Nanofibers Decorated with Noble Metal Nanoparticles for Chemical Sensing.

Science.gov (United States)

Chen, Chen; Tang, Yongan; Vlahovic, Branislav; Yan, Fei

2017-12-01

The integration of different noble metal nanostructures, which exhibit desirable plasmonic and/or electrocatalytic properties, with electrospun polymer nanofibers, which display unique mechanical and thermodynamic properties, yields novel hybrid nanoscale systems of synergistic properties and functions. This review summarizes recent advances on how to incorporate noble metal nanoparticles into electrospun polymer nanofibers and illustrates how such integration paves the way towards chemical sensing applications with improved sensitivity, stability, flexibility, compatibility, and selectivity. It is expected that further development of this field will eventually make a wide impact on many areas of research.

Noble gas control room accident filtration system for severe accident conditions N-CRAFT. System design

International Nuclear Information System (INIS)

Hill, Axel

2014-01-01

Severe accidents might cause the release of airborne radioactive substances to the environment of the NPP. This can either be due to leakages of the containment or due to a filtered containment venting in order to ensure the overall integrity of the containment. During the containment venting process aerosols and iodine can be retained by the FCVS which prevents long term ground contamination. Noble gases are not retainable by the FCVS. From this it follows that a large amount of radioactive noble gases (e.g. xenon, krypton) might be present in the nearby environment of the plant dominating the activity release, depending on the venting procedure and the weather conditions. Accident management measures are necessary in case of severe accidents and the prolonged stay of staff inside the main control room (MCR) or emergency response center (ERC) is essential. Therefore, the in leakage and contamination of the MRC and ERC with airborne activity has to be prevented. The radiation exposure of the crises team needs to be minimized. The entrance of noble gases cannot be sufficiently prevented by the conventional air filtration systems such as HEPA filters and iodine absorbers. With the objective to prevent an unacceptable contamination of the MCR/ERC atmosphere by noble gases AREVA GmbH has developed a noble gas retention system. The noble gas control room accident filtration system CRAFT is designed for this case and provides supply of fresh air to the MCR/ERC without time limitation. The retention process of the system is based on the dynamic adsorption of noble gases on activated carbon. The system consists of delay lines (carbon columns) which are operated by a continuous and simultaneous adsorption and desorption process. These cycles ensure a periodic load and flushing of the delay lines retaining the noble gases from entering the MCR. CRAFT allows a minimization of the dose rate inside MCR/ERC and ensures a low radiation exposure to the staff on shift maintaining

A nanogenerator as a self-powered sensor for measuring the vibration spectrum of a drum membrane

Science.gov (United States)

Yu, Aifang; Zhao, Yong; Jiang, Peng; Wang, Zhong Lin

2013-02-01

A nanogenerator (NG) is a device that converts vibration energy into electricity. Here, a flexible, small size and lightweight NG is successfully demonstrated as an active sensor for detecting the vibration spectrum of a drum membrane without the use of an external power source. The output current/voltage signal of the NG is a direct measure of the strain of the local vibrating drum membrane that contains rich informational content, such as, notably, the vibration frequency, vibration speed and vibration amplitude. In comparison to the laser vibrometer, which is excessively complex and expensive, this kind of small and low cost sensor based on an NG is also capable of detecting the local vibration frequency of a drum membrane accurately. A spatial arrangement of the NGs on the membrane can provide position-dependent vibration information on the surface. The measured frequency spectrum can be understood on the basis of the theoretically calculated vibration modes. This work expands the application of NGs and reveals the potential for developing sound wave detection, environmental/infrastructure monitoring and many more applications.

Intentions of fast noble gas ions with clean and with oxidized monocrystalline copper surfaces

International Nuclear Information System (INIS)

Wit, A.G.J. de.

1979-01-01

The thesis reports investigations concerning the distorted shape of the energy distribution of scattered noble gas ions, and investigations of angular distributions of these ions where a quantitative interpretation is less hampered by preferential neutralization. Low energy noble gas ion scattering is used to study the interactions between oxygen gas and Cu(110) surfaces. (Auth.)

Granular flow in a rotating drum: Experiments and theory

Science.gov (United States)

Hung, C. Y.; Stark, C. P.; Capart, H.; Li, L.; Smith, B.; Grinspun, E.

2015-12-01

Erosion at the base of a debris flow fundamentally controls how large the flow will become and how far it will travel. Experimental observations of this important phenomenon are rather limited, and this lack has led theoretical treatments to making ad hoc assumptions about the basal process. In light of this, we carried out a combination of laboratory experiments and theoretical analysis of granular flow in a rotating drum, a canonical example of steady grain motion in which entrainment rates can be precisely controlled. Our main result is that basal sediment is entrained as the velocity profile adjusts to imbalance in the flow of kinetic energy.Our experimental apparatus consisted of a 40cm-diameter drum, 4cm-deep, half-filled with 2.3mm grains. Rotation rates varied from 1-70 rpm. We varied the effective scale by varying effective gravity from 1g to 70g on a geotechnical centrifuge. The field of grain motion was recorded using high-speed video and mapped using particle tracking velocimetry. In tandem we developed a depth-averaged theory using balance equations for mass, momentum and kinetic energy. We assumed a linearized GDR Midi granular rheology [da Cruz, 2005] and a Coulomb friction law along the sidewalls [Jop et al., 2005]. A scaling analysis of our equations yields a dimensionless "entrainment number" En, which neatly parametrizes the flow geometry in the drum for a wide range of variables, e.g., rotation rate and effective gravity. At low En, the flow profile is planar and kinetic energy is balanced locally in the flow layer. At high En, the flow profile is sigmoidal (yin-yang shaped) and the kinetic energy is dominated by longitudinal, streamwise transfer. We observe different scaling behavior under each of these flow regimes, e.g., between En and kinetic energy, surface slope and flow depth. Our theory correctly predicts their scaling exponents and the value of En at which the regime transition takes place. We are also able to make corrections for

Batteryless wireless transmission system for electronic drum uses piezoelectric generator for play signal and power source

International Nuclear Information System (INIS)

Nishikawa, H; Yoshimi, A; Takemura, K; Tanaka, A; Douseki, T

2015-01-01

A batteryless self-powered wireless transmission system has been developed that sends a signal from a drum pad to a synthesizer. The power generated by a piezoelectric generator functions both as the “Play” signal for the synthesizer and as the power source for the transmitter. An FM transmitter, which theoretically operates with zero latency, and a receiver with quick-response squelch of the received signal were developed for wireless transmission with a minimum system delay. Experimental results for an electronic drum without any connecting wires fully demonstrated the feasibility of self-powered wireless transmission with a latency of 900 μs. (paper)

Performance Demonstration Program Plan for Nondestructive Assay of Drummed Wastes for the TRU Waste Characterization Program

International Nuclear Information System (INIS)

2005-01-01

The Performance Demonstration Program (PDP) for Nondestructive Assay (NDA) is a test program designed to yield data on measurement system capability to characterize drummed transuranic (TRU) waste generated throughout the Department of Energy (DOE) complex. The tests are conducted periodically and provide a mechanism for the independent and objective assessment of NDA system performance and capability relative to the radiological characterization objectives and criteria of the Office of Characterization and Transportation (OCT). The primary documents requiring an NDA PDP are the Waste Acceptance Criteria for the Waste Isolation Pilot Plant (WAC), which requires annual characterization facility participation in the PDP, and the Quality Assurance Program Document (QAPD). This NDA PDP implements the general requirements of the QAPD and applicable requirements of the WAC. Measurement facilities must demonstrate acceptable radiological characterization performance through measurement of test samples comprised of pre-specified PDP matrix drum/radioactive source configurations. Measurement facilities are required to analyze the NDA PDP drum samples using the same procedures approved and implemented for routine operational waste characterization activities. The test samples provide an independent means to assess NDA measurement system performance and compliance per criteria delineated in the NDA PDP Plan. General inter-comparison of NDA measurement system performance among DOE measurement facilities and commercial NDA services can also be evaluated using measurement results on similar NDA PDP test samples. A PDP test sample consists of a 55-gallon matrix drum containing a waste matrix type representative of a particular category of the DOE waste inventory and nuclear material standards of known radionuclide and isotopic composition typical of DOE radioactive material. The PDP sample components are made available to participating measurement facilities as designated by the

Improvements in and relating to drums for storing fuel assemblies of nuclear reactors

International Nuclear Information System (INIS)

Artemiev, L.N.; Batjukov, V.I.; Fadeev, A.I.

1977-01-01

A specification is given for an improved design of drums used for storing nuclear reactor fuel assemblies. It is claimed that this new design reduces wear, increases reliability and enables the recharging operation to be speeded up. (UK)

Is the thermodynamic behavior of the noble fluids consistent with the principle of corresponding states?

NARCIS (Netherlands)

Kulinskii, V.L.; Malomuzh, N.P.; Matvejchuk, O.I.

2009-01-01

The applicability of the Principle of Corresponding States (PCS) for the noble fluids is discussed. We give the thermodynamic evidence for the dimerization of the liquid phase in heavy noble gases like argon, krypton etc. which manifests itself in deviations from the PCS. The behavior of the

A general approach to mesoporous metal oxide microspheres loaded with noble metal nanoparticles

KAUST Repository

Jin, Zhao; Xiao, Manda; Bao, Zhihong; Wang, Peng; Wang, Jianfang

2012-01-01

Catalytic microspheres: A general approach is demonstrated for the facile preparation of mesoporous metal oxide microspheres loaded with noble metal nanoparticles (see TEM image in the picture). Among 18 oxide/noble metal catalysts, TiO 2/0.1 mol Pd microspheres showed the highest turnover frequency in NaBH 4 reduction of 4-nitrophenol (see picture). Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A general approach to mesoporous metal oxide microspheres loaded with noble metal nanoparticles

KAUST Repository

Jin, Zhao

2012-04-26

Catalytic microspheres: A general approach is demonstrated for the facile preparation of mesoporous metal oxide microspheres loaded with noble metal nanoparticles (see TEM image in the picture). Among 18 oxide/noble metal catalysts, TiO 2/0.1 mol Pd microspheres showed the highest turnover frequency in NaBH 4 reduction of 4-nitrophenol (see picture). Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

First Industrial Tests of a Matrix Monitor Correction for the Differential Die-away Technique of Historical Waste Drums

Energy Technology Data Exchange (ETDEWEB)

Antoni, Rodolphe; Passard, Christian; Perot, Bertrand [CEA Cadarache DEN/Nuclear Measurement Laboratory, 13108 Saint-Paul lez Durance (France); Batifol, Marc; Vandamme, Jean-Christophe [Nuclear Measurement Team, AREVA NC, La Hague plant F-50444 Beaumont-Hague (France); Grassi, Gabriele [AREVA NC, 1 place Jean-Millier, 92084 Paris-La-Defense cedex (France)

2015-07-01

The fissile mass in radioactive waste drums filled with compacted metallic residues (spent fuel hulls and nozzles) produced at AREVA NC La Hague reprocessing plant is measured by neutron interrogation with the Differential Die-away measurement Technique (DDT). In the next years, old hulls and nozzles mixed with Ion-Exchange Resins will be measured. The ion-exchange resins increase neutron moderation in the matrix, compared to the waste measured in the current process. In this context, the Nuclear Measurement Laboratory (LMN) of CEA Cadarache has studied a matrix effect correction method, based on a drum monitor, namely a 3He proportional counter located inside the measurement cavity. After feasibility studies performed with LMN's PROMETHEE 6 laboratory measurement cell and with MCNPX simulations, this paper presents first experimental tests performed on the industrial ACC (hulls and nozzles compaction facility) measurement system. A calculation vs. experiment benchmark has been carried out by performing dedicated calibration measurements with a representative drum and {sup 235}U samples. The comparison between calculation and experiment shows a satisfactory agreement for the drum monitor. The final objective of this work is to confirm the reliability of the modeling approach and the industrial feasibility of the method, which will be implemented on the industrial station for the measurement of historical wastes. (authors)

Control of thermoacoustic instability with a drum-like silencer

Science.gov (United States)

Zhang, Guangyu; Wang, Xiaoyu; Li, Lei; Jing, Xiaodong; Sun, Xiaofeng

2017-10-01

Theoretical investigation is carried out by a novel method of controlling thermoacoustic instability with a drum-like silencer. It is shown that by decreasing the frequency of thermoacoustic system, the instability can be suppressed with the help of drum-like silencer. The purely reactive silencer, which is composed of a flexible membrane and a backing cavity, is usually known as a noise control device that works effectively in low frequency bandwidth without any aerodynamic loss. In present research, the silencer is exploited in a Rijke tube, as a means of decreasing the natural frequency of the system, and consequently changing the resonance period of the system. The "transfer element method" (TEM) is used to consider the interactions between the acoustic waves and the flexible membranes of the silencer. The effects of all possible properties of the silencer on the growth rate and resonance frequency of the thermoacoustic system are explored. According to the calculation results, it is found that for some properties of the silencer, the resonance frequencies are greatly decreased and then the phase difference between the unsteady heat release and the pressure fluctuation is increased. Consequently, the instability is suppressed with some dissipation that can not be able to control its onset in the original system. Therefore, when the damping is low, but not zero, it is effective to control thermoacoustic instability with this technique.

Properties and application of noble metal catalysts for heterogeneous catalytic hydrogenations

Energy Technology Data Exchange (ETDEWEB)

Horn, G; Frohning, C D; Cornils, B [Ruhrchemie A.G., Oberhausen (Germany, F.R.)

1976-07-01

The special properties of the six platinum group elements - ruthenium, rhodium, palladium, osmium, iridium, platinum - make them useful as active metals for catalytic reactions. Especially valuable is their property of favouring a single reaction even when the possibility of a number of parallel reactions exists under certain reaction conditions. This selectivity of the noble metal catalyst may be directed or enhanced through appropriate choise of the metal, the reaction conditions, the duration of the reaction, the amount of hydrogen etc. Even the physical state of the catalyst - supported or unsupported - is of influence when using noble metal catalysts as described in this report.

Fluorescence emissions from mixtures of Hg with the noble gases

International Nuclear Information System (INIS)

Woodworth, J.R.

1977-01-01

Fluorescence emissions from mixtures of Hg with high pressure Xe, Kr, and Ar (approx.1 torr Hg, 10 3 --10 4 torr noble gas) have been studied using a short-pulse relativistic electron beam as an excitation source. Hg--noble gas molecular bands were observed on the red sides of the Hg lines (1849 and 2537 A) as well as on the red sides of the Hg visible lines (7 3 S 1 →6 3 P 0 , 1 , 2 ). Temporal histories and production efficiencies of the molecular emissions were determined and a model was formulated for the time histories of the HgXe 2600 A bands. Possible applications to high power laser systems are discussed

Effect of salinity on the upper lethal temperature tolerance of early-juvenile red drum.

Science.gov (United States)

McDonald, Dusty; Bumguardner, Britt; Cason, Paul

2015-10-01

Previous work investigating the temperature tolerance of juvenile red drum ranging 18-50mm TL found evidence for positive size dependence (smaller fish less tolerant to higher temperatures) suggesting smaller size classes (temperatures. Here, we explored the upper lethal temperature tolerance (ULT) in smaller-sized red drum which ranged from 10 to 20mm TL across multiple salinities to further understand the thermal limitations of this propagated game fish. In order to investigate the combined effect of temperature and salinity on ULT, temperature trials were conducted under three levels of salinity which commonly occur along the coast of Texas (25, 35, and 45ppt). The rate of temperature increase (+0.25°C/h) was designed to mimic a natural temperature increase of a summer day in Texas. We determined that the lethal temperature at 50% (LT50) did not differ between the three salinities examined statistically; median lethal temperature for individuals exposed to 25ppt ranged from 36.4 to 37.7°C, 35ppt ranged from 36.4 to 37.7°C, and 45ppt ranged from 36.1 to 37.4°C. Further, LT50 data obtained here for early-juvenile red drum did not differ from data of a similar experiment examining 25mm TL sized fish. Published by Elsevier Ltd.

Vitrification of noble metals containing NCAW simulant with an engineering scale melter (ESM): Campaign report

Energy Technology Data Exchange (ETDEWEB)

Grunewald, W.; Roth, G.; Tobie, W.; Weisenburger, S.; Weiss, K.; Elliott, M.; Eyler, L.L.

1996-03-01

ESM has been designed as a 10th-scale model of the DWPF-type melter, currently the reference melter for nitrification of Hanford double shell tankwaste. ESM and related equipment have been integrated to the existing mockup vitrification plant VA-WAK at KfK. On June 2-July 10, 1992, a shakedown test using 2.61 m{sup 3} of NCAW (neutralized current acid waste) simulant without noble metals was performed. On July 11-Aug. 30, 1992, 14.23 m{sup 3} of the same simulant with nominal concentrations of Ru, Rh, and Pd were vitrified. Objective was to investigate the behavior of such a melter with respect to discharge of noble metals with routine glass pouring via glass overflow. Results indicate an accumulation of noble metals in the bottom area of the flat-bottomed ESM. About 65 wt% of the noble metals fed to the melter could be drained out, whereas 35 wt% accumulated in the melter, based on analysis of glass samples from glass pouring stream in to the canisters. After the melter was drained at the end of the campaign through a bottom drain valve, glass samples were taken from the residual bottom layer. The samples had significantly increased noble metals content (factor of 20-45 to target loading). They showed also a significant decrease of the specific electric resistance compared to bulk glass (factor of 10). A decrease of 10- 15% of the resistance between he power electrodes could be seen at the run end, but the total amount of noble metals accumulated was not yet sufficient enough to disturb the Joule heating of the glass tank severely.

Heat and water transfer in a rotating drum containing solid substrate particles

NARCIS (Netherlands)

Schutyser, M.A.I.; Weber, F.J.; Briels, W.J.; Rinzema, A.; Boom, R.M.

2003-01-01

In previous work we reported on the simulation of mixing behavior of a slowly rotating drum for solid-state fermentation (SSF) using a discrete particle model. In this investigation the discrete particle model is extended with heat and moisture transfer. Heat transfer is implemented in the model via

Development and engineering application of rotating drum acid-curing equipment in uranium mills

International Nuclear Information System (INIS)

Liu Wenhua

2006-01-01

The development and engineering application of rotating drum acid-curing equipment for 'strong acid-curing and ferri-trickle leaching' process are introduced, including the design of main structure, problems appeared in the development and engineering application, and methods solved. (authors)

Line emissions from sonoluminescence in aqueous solutions of halide salts without noble gases

Energy Technology Data Exchange (ETDEWEB)

Liang, Jinfu, E-mail: liang.shi2007@163.com [The Key Laboratory of Modern Acoustics, Ministry of Education, Institution of Acoustics, Nanjing University, Nanjing 210093 (China); School of Physics and Electronic Science, Guizhou Normal University, Guiyang 550001 (China); Chen, Weizhong, E-mail: wzchen@nju.edu.cn [The Key Laboratory of Modern Acoustics, Ministry of Education, Institution of Acoustics, Nanjing University, Nanjing 210093 (China); Zhou, Chao; Cui, Weicheng; Chen, Zhan [The Key Laboratory of Modern Acoustics, Ministry of Education, Institution of Acoustics, Nanjing University, Nanjing 210093 (China)

2015-02-20

Line emissions of trivalent terbium (Tb{sup 3+}) ion were observed from single-bubble sonoluminescence (SL) in an aqueous solution of terbium chloride (TbCl{sub 3}) that contained no noble gas. In addition, sodium (Na) lines were observed in multi-bubble SL in aqueous solutions of various halide salts that contained no noble gas. These observations show that the halide ions, such as Cl{sup −}, Br{sup −}, and I{sup −}, help for line emissions as the noble gases. The intensity of a line emission depends on both the chemical species produced by cavitation bubbles and the temperature of SL bubble that responds to the driving ultrasound pressure. With the increase of driving pressure, some line emissions attached to the continuous spectrum may become increasingly clear, while other line emissions gradually become indistinct. - Highlights: • Line emissions of Tb(III) ions were observed without the presence of noble gases. • The halide ions help to generate a line emission during sonoluminescence. • The intensity of a line emission mainly depends on the bubble's temperature. • The definition of a line emission is related to the temperature of caviation bubble and the kind of host liquid.

Noble metal behavior during melting of simulated high-level nuclear waste glass feeds

International Nuclear Information System (INIS)

Anderson, L.D.; Dennis, T.; Elliott, M.L.; Hrma, P.

1993-04-01

Noble metals and their oxides can settle in waste glass melters and cause electrical shorting. Simulated waste feeds from Hanford, Savannah River, and Germany were heat treated for 1 hour in a gradient furnace at temperatures ranging from approximately 600 degrees C--1000 degrees C and examined by electron microscopy to determine shapes, sizes, and distribution of noble metal particles as a function of temperature. Individual noble metal particles and agglomerates of rhodium (Rh), ruthenium (RuO 2 ), and palladium (Pd), as well as their alloys, were seen. the majority of particles and agglomerates were generally less than 10 microns; however, large agglomerations (up to 1 mm) were found in the German feed. Detailed particle distribution and characterization was performed for a Hanford waste to provide input to computer modeling of particle settling in the melter

DRUMS: Disk Repository with Update Management and Select option for high throughput sequencing data.

Science.gov (United States)

Nettling, Martin; Thieme, Nils; Both, Andreas; Grosse, Ivo

2014-02-04

New technologies for analyzing biological samples, like next generation sequencing, are producing a growing amount of data together with quality scores. Moreover, software tools (e.g., for mapping sequence reads), calculating transcription factor binding probabilities, estimating epigenetic modification enriched regions or determining single nucleotide polymorphism increase this amount of position-specific DNA-related data even further. Hence, requesting data becomes challenging and expensive and is often implemented using specialised hardware. In addition, picking specific data as fast as possible becomes increasingly important in many fields of science. The general problem of handling big data sets was addressed by developing specialized databases like HBase, HyperTable or Cassandra. However, these database solutions require also specialized or distributed hardware leading to expensive investments. To the best of our knowledge, there is no database capable of (i) storing billions of position-specific DNA-related records, (ii) performing fast and resource saving requests, and (iii) running on a single standard computer hardware. Here, we present DRUMS (Disk Repository with Update Management and Select option), satisfying demands (i)-(iii). It tackles the weaknesses of traditional databases while handling position-specific DNA-related data in an efficient manner. DRUMS is capable of storing up to billions of records. Moreover, it focuses on optimizing relating single lookups as range request, which are needed permanently for computations in bioinformatics. To validate the power of DRUMS, we compare it to the widely used MySQL database. The test setting considers two biological data sets. We use standard desktop hardware as test environment. DRUMS outperforms MySQL in writing and reading records by a factor of two up to a factor of 10000. Furthermore, it can work with significantly larger data sets. Our work focuses on mid-sized data sets up to several billion

Salt Composition Derived from Veazey Composition by Thermodynamic Modeling and Predicted Composition of Drum Contents

Energy Technology Data Exchange (ETDEWEB)

Weisbrod, Kirk Ryan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Veirs, Douglas Kirk [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Funk, David John [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Clark, David Lewis [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-03-11

This report describes the derivation of the salt composition from the Veazey salt stream analysis. It also provides an estimate of the proportions of the kitty litter, nitrate salt and neutralizer that was contained in drum 68660. While the actinide content of waste streams was judiciously followed in the 1980s in TA-55, no record of the salt composition could be found. Consequently, a salt waste stream produced from 1992 to 1994 and reported by Gerry Veazey provided the basis for this study. While chemical analysis of the waste stream was highly variable, an average analysis provided input to the Stream Analyzer software to calculate a composition for a concentrated solid nitrate salt and liquid waste stream. The calculation predicted the gas / condensed phase compositions as well as solid salt / saturated liquid compositions. The derived composition provides an estimate of the nitrate feedstream to WIPP for which kinetic measurements can be made. The ratio of salt to Swheat in drum 68660 contents was estimated through an overall mass balance on the parent and sibling drums. The RTR video provided independent confirmation concerning the volume of the mixture. The solid salt layer contains the majority of the salt at a ratio with Swheat that potentially could become exothermic.

Salt Composition Derived from Veazey Composition by Thermodynamic Modeling and Predicted Composition of Drum Contents

International Nuclear Information System (INIS)

Weisbrod, Kirk Ryan; Veirs, Douglas Kirk; Funk, David John; Clark, David Lewis

2016-01-01

This report describes the derivation of the salt composition from the Veazey salt stream analysis. It also provides an estimate of the proportions of the kitty litter, nitrate salt and neutralizer that was contained in drum 68660. While the actinide content of waste streams was judiciously followed in the 1980s in TA-55, no record of the salt composition could be found. Consequently, a salt waste stream produced from 1992 to 1994 and reported by Gerry Veazey provided the basis for this study. While chemical analysis of the waste stream was highly variable, an average analysis provided input to the Stream Analyzer software to calculate a composition for a concentrated solid nitrate salt and liquid waste stream. The calculation predicted the gas / condensed phase compositions as well as solid salt / saturated liquid compositions. The derived composition provides an estimate of the nitrate feedstream to WIPP for which kinetic measurements can be made. The ratio of salt to Swheat in drum 68660 contents was estimated through an overall mass balance on the parent and sibling drums. The RTR video provided independent confirmation concerning the volume of the mixture. The solid salt layer contains the majority of the salt at a ratio with Swheat that potentially could become exothermic.

Research of plating aluminum and aluminum foil on internal surface of carbon fiber composite material centrifuge rotor drum

International Nuclear Information System (INIS)

Lu Xiuqi; Dong Jinping; Dai Xingjian

2014-01-01

In order to improve the corrosion resistance, thermal conductivity and sealability of the internal surface of carbon fiber/epoxy composite material centrifuge rotor drum, magnetron sputtering aluminum and pasting an aluminum foil on the inner wall of the drum are adopted to realize the aim. By means of XRD, SEM/EDS and OM, the surface topography of aluminum coated (thickness of 5 μm and 12 μm) and aluminum foil (12 μm) are observed and analyzed; the cohesion of between aluminum coated (or aluminum foil) and substrate material (CFRP) is measured by scratching experiment, direct drawing experiment, and shear test. Besides, the ultra-high-speed rotation experiment of CFRP ring is carried out to analyze stress and strain of coated aluminum (or aluminum foil) which is adhered on the ring. The results showed aluminum foil pasted on inner surface do better performance than magnetron sputtering aluminum on CFRP centrifuge rotor drum. (authors)

Growth responses of Neurospora crassa to increased partial pressures of the noble gases and nitrogen.

Science.gov (United States)

Buchheit, R G; Schreiner, H R; Doebbler, G F

1966-02-01

Buchheit, R. G. (Union Carbide Corp., Tonawanda, N.Y.), H. R. Schreiner, and G. F. Doebbler. Growth responses of Neurospora crassa to increased partial pressures of the noble gases and nitrogen. J. Bacteriol. 91:622-627. 1966.-Growth rate of the fungus Neurospora crassa depends in part on the nature of metabolically "inert gas" present in its environment. At high partial pressures, the noble gas elements (helium, neon, argon, krypton, and xenon) inhibit growth in the order: Xe > Kr> Ar > Ne > He. Nitrogen (N(2)) closely resembles He in inhibitory effectiveness. Partial pressures required for 50% inhibition of growth were: Xe (0.8 atm), Kr (1.6 atm), Ar (3.8 atm), Ne (35 atm), and He ( approximately 300 atm). With respect to inhibition of growth, the noble gases and N(2) differ qualitatively and quantitatively from the order of effectiveness found with other biological effects, i.e., narcosis, inhibition of insect development, depression of O(2)-dependent radiation sensitivity, and effects on tissue-slice glycolysis and respiration. Partial pressures giving 50% inhibition of N. crassa growth parallel various physical properties (i.e., solubilities, solubility ratios, etc.) of the noble gases. Linear correlation of 50% inhibition pressures to the polarizability and of the logarithm of pressure to the first and second ionization potentials suggests the involvement of weak intermolecular interactions or charge-transfer in the biological activity of the noble gases.

Non-noble metal based electro-catalyst compositions for proton exchange membrane based water electrolysis and methods of making

Science.gov (United States)

Kumta, Prashant N.; Kadakia, Karan Sandeep; Datta, Moni Kanchan; Velikokhatnyi, Oleg

2017-02-07

The invention provides electro-catalyst compositions for an anode electrode of a proton exchange membrane-based water electrolysis system. The compositions include a noble metal component selected from the group consisting of iridium oxide, ruthenium oxide, rhenium oxide and mixtures thereof, and a non-noble metal component selected from the group consisting of tantalum oxide, tin oxide, niobium oxide, titanium oxide, tungsten oxide, molybdenum oxide, yttrium oxide, scandium oxide, cooper oxide, zirconium oxide, nickel oxide and mixtures thereof. Further, the non-noble metal component can include a dopant. The dopant can be at least one element selected from Groups III, V, VI and VII of the Periodic Table. The compositions can be prepared using a surfactant approach or a sol gel approach. Further, the compositions are prepared using noble metal and non-noble metal precursors. Furthermore, a thin film containing the compositions can be deposited onto a substrate to form the anode electrode.

Tracing enhanced oil recovery signatures in casing gases from the Lost Hills oil field using noble gases

Science.gov (United States)

Barry, Peter H.; Kulongoski, Justin; Landon, Matthew K.; Tyne, R.L.; Gillespie, Janice; Stephens, Michael; Hillegonds, D.J.; Byrne, D.J.; Ballentine, C.J.

2018-01-01

Enhanced oil recovery (EOR) and hydraulic fracturing practices are commonly used methods to improve hydrocarbon extraction efficiency; however the environmental impacts of such practices remain poorly understood. EOR is particularly prevalent in oil fields throughout California where water resources are in high demand and disposal of high volumes of produced water may affect groundwater quality. Consequently, it is essential to better understand the fate of injected (EOR) fluids in California and other subsurface petroleum systems, as well as any potential effect on nearby aquifer systems. Noble gases can be used as tracers to understand hydrocarbon generation, migration, and storage conditions, as well as the relative proportions of oil and water present in the subsurface. In addition, a noble gas signature diagnostic of injected (EOR) fluids can be readily identified. We report noble gas isotope and concentration data in casing gases from oil production wells in the Lost Hills oil field, northwest of Bakersfield, California, and injectate gas data from the Fruitvale oil field, located within the city of Bakersfield. Casing and injectate gas data are used to: 1) establish pristine hydrocarbon noble-gas signatures and the processes controlling noble gas distributions, 2) characterize the noble gas signature of injectate fluids, 3) trace injectate fluids in the subsurface, and 4) construct a model to estimate EOR efficiency. Noble gas results range from pristine to significantly modified by EOR, and can be best explained using a solubility exchange model between oil and connate/formation fluids, followed by gas exsolution upon production. This model is sensitive to oil-water interaction during hydrocarbon expulsion, migration, and storage at reservoir conditions, as well as any subsequent modification by EOR.

Paleotemperatures derived from noble gases dissolved in groundwater and in relation to soil temperature

International Nuclear Information System (INIS)

Stute, M.; Sonntag, C.

1992-01-01

Measurements of He, Ne, Ar, Kr and Xe dissolved in groundwater at two sites (Bocholt, Germany, and the Great Hungarian Plain) were taken to prove the reliability of noble gas temperatures as indicators of paleotemperatures. Noble gas temperatures of groundwater of Holocene age were found to reflect the annual mean soil temperature in the recharge are with an accuracy close to the precision of measurement (1σ approx. ±0.5 deg. C). Noble gas temperature data demonstrate the influence of vegetation cover on the soil temperature in the infiltration area. Groundwater formed in forests at the Bocholt site shows noble gas temperatures that are 2.2 deg. C lower than the groundwater formed in fields or meadows. The temperature data obtained from groundwater of the Great Hungarian Plain for the last glaciation are ≥ 8.6 deg. C lower than data from recent groundwater for maximum glaciation (approx. 18,000 years ago) and 4.7 ± 1 deg. C lower for the preceding interstadial (approx. 28,000-35,000 years ago). These data permit independent reconstruction of paleoclimatic conditions. (author). 19 refs, 3 figs, 1 tab

The impact of specialist trauma service on major trauma mortality.

Science.gov (United States)

Wong, Ting Hway; Lumsdaine, William; Hardy, Benjamin M; Lee, Keegan; Balogh, Zsolt J

2013-03-01

Trauma services throughout the world have had positive effects on trauma-related mortality. Australian trauma services are generally more consultative in nature rather than the North American model of full trauma admission service. We hypothesized that the introduction of a consultative specialist trauma service in a Level I Australian trauma center would reduce mortality of the severely injured. A 10-year retrospective study (January 1, 2002-December 31, 2011) was performed on all trauma patients admitted with an Injury Severity Score (ISS) > 15. Patients were identified from the trauma registry, and data for age, sex, mechanism of injury, ISS, survival to discharge, and length of stay were collected. Mortality was examined for patients with severe injury (ISS > 15) and patients with critical injury (ISS > 24) and compared for the three periods: 2002-2004 (without trauma specialist), 2005-2007 (with trauma specialist), and 2008-2011 (with specialist trauma service). A total of 3,869 severely injured (ISS > 15) trauma patients were identified during the 10-year period. Of these, 2,826 (73%) were male, 1,513 (39%) were critically injured (ISS > 24), and more than 97% (3,754) were the victim of blunt trauma. Overall mortality decreased from 12.4% to 9.3% (relative risk, 0.75) from period one to period three and from 25.4% to 20.3% (relative risk, 0.80) for patients with critical injury. A 0.46% per year decrease (p = 0.018) in mortality was detected (odds ratio, 0.63; p 24), the trend was (0.61% per year; odds ratio, 0.68; p = 0.039). The introduction of a specialist trauma service decreased the mortality of patients with severe injury, the model of care should be considered to implement state- and nationwide in Australia. Epidemiologic study, level III.

The Role of Noble Metal Addition Methods on BWR Shut Down Dose Rates

International Nuclear Information System (INIS)

Cowan, Robert L.; Garcia Susan, E.

2012-09-01

Noble metal addition technology was developed for the BWR as a means of establishing low electrochemical corrosion potentials (ECP) on structural materials to mitigate intergranular stress corrosion cracking (IGSCC). When the reactor water molar ratio of H 2 / (O 2 +H 2 O 2 ) is > 2 on noble metal treated surfaces, the resulting ECP is near -500 mV (SHE), well into the mitigation range. This ratio can be achieved in most areas of the reactor with feedwater hydrogen additions in the range of 0.2 mg/kg, a condition that does not increase the radiation level in the main steam, a side effect of conventional hydrogen water chemistry (HWC). The resulting low ECP on the surface of stainless steel piping and components results in a change in form of the stable corrosion film to a spinel structure. Since it is the 60 Co incorporated into the corrosion film that is the primary source term of shutdown dose rates in BWRs, the structure and composition of the film can have a large influence in the resulting dose rates. The results of the first generation of noble metal technology, noble metal chemical addition (NMCA), showed that the reactor water ratio of 60 Co (s)/Zn (s) was a key parameter in determining shut down dose rate values. This paper will review that history and provide mechanistic understanding of how initial post NMCA dose rates are established and change with time. On-line noble metal chemical addition (OLNC) is the second generation of noble metal technology. The method utilizes the on-line injection of dilute Na 2 Pt (OH) 6 into the feedwater over a period of approximately 10 days. The first application of OLNC occurred at a European reactor in July of 2005 and to date over 20 BWRs have applied the technology, with many more applications scheduled. It is expected that OLNC will become the de facto standard because it eliminates 60 hours of outage application time and it addresses the crack flanking concerns that can arise under certain conditions. Because both

Color image digitization and analysis for drum inspection

International Nuclear Information System (INIS)

Muller, R.C.; Armstrong, G.A.; Burks, B.L.; Kress, R.L.; Heckendorn, F.M.; Ward, C.R.

1993-01-01

A rust inspection system that uses color analysis to find rust spots on drums has been developed. The system is composed of high-resolution color video equipment that permits the inspection of rust spots on the order of 0.25 cm (0.1-in.) in diameter. Because of the modular nature of the system design, the use of open systems software (X11, etc.), the inspection system can be easily integrated into other environmental restoration and waste management programs. The inspection system represents an excellent platform for the integration of other color inspection and color image processing algorithms

Rotating drum tests of particle suspensions within a fines dispersion

Science.gov (United States)

Cabrera, Miguel Angel; Gollin, Devis; Kaitna, Roland; Wu, Wei

2014-05-01

Natural flows like mudflows, debris flow, and hyperconcentrated flows are commonly composed by a matrix of particles suspended in a viscous fluid. The nature of the interactions between particles immersed in a fluid is related to its size. While coarse particles (sand, gravel, and boulders) interact with each other or with the surrounding fluid, a dispersion of fine particles interacts with each other through colloidal forces or Brownian motion effects (Coussot and Piau, 1995, and Ancey and Jorrot, 2001). The predominance of one of the previous interactions defines the rheology of the flow. On this sense, experimental insight is required to validate the limits where the rheology of a dispersion of fines is valid. For this purpose, an experimental program in a rotating drum is performed over samples of sand, loess, and kaolin. The solid concentration and angular velocity of the rotating drum are varied. Height and normal loads are measured during flow. High-speed videos are performed to obtain the flow patterns of the mixtures. The experiments provide new laboratory evidence of granular mixture behaviour within an increased viscous fluid phase and its characterization. The results show an apparent threshold in terms of solid concentration, in which the mixtures started to behave as a shear-dependent material.

Advancing the use of noble gases in fluid inclusions of speleothems as a palaeoclimate proxy. Method and standardization

International Nuclear Information System (INIS)

Papp, L.; Palcsu, L.; Major, Z.; Svingor, E.

2010-01-01

Complete text of publication follows. Continental carbonates are essential archives of the past geological and climatological occurrences. Recently, fluid inclusions of carbonates have got into focus of palaeoclimate research. A new approach using temperature dependent gas solubilities might be a way that uses only physical laws, e.g. the Henry's law of solubility and gas partitioning models. The so-called noble gas temperature (NGT) can be calculated from the measured noble gas concentrations. This report describes how our first advancing steps towards obtaining NGT's from fluid inclusions and tiny water amounts have been preformed. To extract the water inclusions from the carbonate matrix, the most suitable treatment is to crush the carbonate under vacuum. The water released from the inclusions is then collected in a cold finger by freezing. The amount of the liberated water is measured via its vapour pressure in a certain volume (Fig. 1). The liberated dissolved noble gases which were in the fluid inclusions are separated by a cryo system, and then admitted into the static mode noble gas mass spectrometer sequentially. The calibration of the noble gas mass spectrometric measurements is performed by means of well known air aliquots. To check the reliability of the whole measurement procedure standard water samples have to be measured. As for standard samples, first we have prepared air equilibrated water (AEW) in conditioned circumstances. We fill copper capillaries with AEW. Having completed the copper capillary assemblage, the AEW is letting flow through the capillary (Fig. 2). The error of such a water determination is less than 1% in case of 1 μl of liquid water (Fig. 1) that allows us to determine accurate noble gas concentrations. The reproducibility of 40 Ar measurements is better than 0.6 %, while those of neon, krypton and xenon isotopes are 0.6-1.6 %, 0.9-2.2 % and 0.8-2.0 %, respectively. Theoretically, these precisions for noble gas concentrations

Radwaste disposal drum centrifuge

International Nuclear Information System (INIS)

Rubin, L.S.; Deltete, C.P.; Crook, M.R.

1988-01-01

The drum or processing bowl of the DDC becomes the disposal container when the filling operation is completed. Rehandling of the processed resin is eliminated. By allowing the centrifugally compacted resin to remain in the processing container, extremely efficient waste packaging can be achieved. The dewatering results and volume reductions reported during 1986 were based upon laboratory scale testing sponsored by the Electric Power Research Institute (EPRI) and the Department of Energy (DOE). Since the publication of these preliminary results, additional testing using a full-scale prototype DDC has been completed, again under the auspices of the DOE. Full-scale testing has substantiated the results of earlier testing and has formed the basis for preliminary discussions with the U.S. Nuclear Regulatory Commission (NRC) regarding DDC licensing for radioactive applications. A comprehensive Topical Report and Process Control Program is currently being prepared for submittal to the NRC for review under a utility licensing action. Detailed cost-benefit analyses for actual plant operations have been prepared to substantiate the attractiveness of the DDC. Several methods to physically integrate a DDC into a nuclear power plant have also been developed

Nanoparticles of noble metals in the supergene zone

Science.gov (United States)

Zhmodik, S. M.; Kalinin, Yu. A.; Roslyakov, N. A.; Mironov, A. G.; Mikhlin, Yu. L.; Belyanin, D. K.; Nemirovskaya, N. A.; Spiridonov, A. M.; Nesterenko, G. V.; Airiyants, E. V.; Moroz, T. N.; Bul'bak, T. A.

2012-04-01

Formation of noble metal nanoparticles is related to various geological processes in the supergene zone. Dispersed mineral phases appear during weathering of rocks with active participation of microorganisms, formation of soil, in aqueous medium and atmosphere. Invisible gold and other noble metals are incorporated into oxides, hydroxides, and sulfides, as well as in dispersed organic and inorganic carbonic matter. Sulfide minerals that occur in bedrocks and ores unaltered by exogenic processes and in cementation zone are among the main concentrators of noble metal nanoparticles. The ability of gold particles to disaggregate is well-known and creates problems in technological and analytical practice. When Au and PGE nanoparticles and clusters occur, these problems are augmented because of their unusual reactions and physicochemical properties. The studied gold, magnetite, titanomagnetite and pyrite microspherules from cementation zone and clay minerals of laterites in Republic of Guinea widen the knowledge of their abundance and inferred formation conditions, in particular, in the contemporary supergene zone. Morphology and composition of micrometer-sized Au mineral spherules were studied with SEM and laser microprobe. The newly formed segregations of secondary gold on the surface of its residual grains were also an object of investigation. The character of such overgrowths is the most indicative for nanoparticles. The newly formed Au particles provide evidence for redistribution of ultradispersed gold during weathering. There are serious prerequisites to state that microorganisms substantially control unusual nano-sized microspherical morphology of gold particles in the supergene zone. This is supported by experiments indicating active absorption of gold by microorganisms and direct evidence for participation of Ralstonia metallidurans bacteria in the formation of peculiar corroded bacteriomorphic surface of gold grains. In addition, the areas enriched in carbon

EDO, Doses to Man and Organs from Reactor Operation Noble Gas and Liquid Waste Release

International Nuclear Information System (INIS)

Rodenas Diago, Jose; Serradell Garcia, Vicente

1983-01-01

1 - Description of problem or function: EDO evaluates individual and collective doses to man from atmospheric releases of noble gases and other gaseous effluents. 2 - Method of solution: The dose calculations are carried out by following the guide- lines of USNRC Regulatory Guide 1.109. Radiation exposure for maximum individuals and population are estimated within 30 km from the nuclear plant. This area is divided into 160 circular trapezoids, to which computations are referred. Four age groups, seven organs for internal dose and two for external dose have been considered. Dose calculations are done through 14 pathways, 7 for liquid effluents, one for noble gases, and 6 for the rest of gaseous effluents. 3 - Restrictions on the complexity of the problem: The following are the maximum dimension sizes preset in the code: 73 radionuclides (other than noble gases); 15 noble gases; 160 circular trapezoids; 31 chemical elements; 4 types of aquatic foods; 15 points of exposure for shorelines; 15 trapezoids influenced by each point; 4 terrestrial food pathways; 100 centres of population. Some of these limits can be varied

EDO, Doses to Man and Organs from Reactor Operation Noble Gas and Liquid Waste Release

Energy Technology Data Exchange (ETDEWEB)

Rodenas Diago, Jose; Serradell Garcia, Vicente [Departamento de Ingenieria Nuclear, Escuela Tecnica Superior de Ingenieros Industriales, Universidad Politecnica, Camino de Vera 2/n Apartado 2012, Valencia (Spain)

1983-10-18

1 - Description of problem or function: EDO evaluates individual and collective doses to man from atmospheric releases of noble gases and other gaseous effluents. 2 - Method of solution: The dose calculations are carried out by following the guide- lines of USNRC Regulatory Guide 1.109. Radiation exposure for maximum individuals and population are estimated within 30 km from the nuclear plant. This area is divided into 160 circular trapezoids, to which computations are referred. Four age groups, seven organs for internal dose and two for external dose have been considered. Dose calculations are done through 14 pathways, 7 for liquid effluents, one for noble gases, and 6 for the rest of gaseous effluents. 3 - Restrictions on the complexity of the problem: The following are the maximum dimension sizes preset in the code: 73 radionuclides (other than noble gases); 15 noble gases; 160 circular trapezoids; 31 chemical elements; 4 types of aquatic foods; 15 points of exposure for shorelines; 15 trapezoids influenced by each point; 4 terrestrial food pathways; 100 centres of population. Some of these limits can be varied.

The Behavior and Effects of the Noble Metals in the DWPF Melter System

International Nuclear Information System (INIS)

Smith, M.E.; Bickford, D.F.

1997-01-01

Governments worldwide have committed to stabilization of high-level nuclear waste (HLW) by vitrification to a durable glass form for permanent disposal. All of these nuclear wastes contain the fission-product noble metals: ruthenium, rhodium, and palladium. SRS wastes also contain natural silver from iodine scrubbers. Closely associated with the noble metals are the fission products selenium and tellurium which are chemical analogs of sulfur and which combine with noble metals to influence their behavior and properties. Experience has shown that these melt insoluble metals and their compounds tend to settle to the floor of Joule-heated ceramic melters. In fact, almost all of the major research and production facilities have experienced some operational problem which can be associated with the presence of dense accumulations of these relatively conductive metals and/or their compounds. In most cases, these deposits have led to a loss of production capability, in some cases, to the point that melter operation could not continue. HLW nuclear waste vitrification facilities in the United States are the Department of Energy's Defense Waste Processing Facility (DWPF) at the Savannah River Site, the planned Hanford Waste Vitrification Plant (HWVP) at the Hanford Site and the operating West Valley Demonstration Project (WVDP) at West Valley, NY. The Integrated DWPF Melter System (IDMS) is a vitrification test facility at the Savannah River Technology Center (SRTC). It was designed and constructed to provide an engineering-scale representation of the DWPF melter and its associated feed preparation and off-gas treatment systems. An extensive noble metals testing program was begun in 1990. The objectives of this task were to explore the effects of the noble metals on the DWPF melter feed preparation and waste vitrification processes. This report focuses on the vitrification portion of the test program

Intelligent Mobile Sensor System for drum inspection and monitoring - Volume 2. Final report, October 1, 1993 - April 22, 1995

International Nuclear Information System (INIS)

1995-01-01

The objective of the Intelligent Mobile Sensor System (IMSS) project was to develop an operational system for monitoring and inspection activities for waste storage facility operations at several DOE sites. Specifically, the product of this effort was a robotic device with enhanced intelligence and maneuverability capable of conducting routine inspection of stored waste drums. The system has an integrated sensor suite for problem-drum detection, and creates and maintains a site database both for inspection planning and for data correlation, updating, and report generation. The system is capable of departing on an assigned mission, collecting required data, recording which portions of its mission had to be aborted or modified due to environmental constraints, and reporting back when the mission is complete. Successful identification of more than 96% of drum defects has been demonstrated in a high fidelity waste storage facility mockup. Identified anomalies included rust spots, rust streaks, areas of corrosion, dents, and tilted drums. All drums were positively identified and correlated with the site database. This development effort was separated into three phases of which phase three is now complete. The first phase demonstrated an integrated system (maturity level IVa) for monitoring and inspection activities for waste storage facility operations. The second phase demonstrated a prototype system appropriate for operational use in an actual storage facility. The prototype employed an integrated design that considered operational requirements, hardware costs, maintenance, safety, and robustness. The final phase has demonstrated the commercial viability of the vehicle in operating waste storage facilities at Fernald, Ohio and the Idaho National Engineering Laboratory (INEL). This report summarizes the system upgrades performed in phase 3 and the evaluation of the IMSS Phase 3 system and vehicle

Intelligent mobile sensor system for drum inspection and monitoring: Phase 1. Topical report, October 1, 1992--June 8, 1993

Energy Technology Data Exchange (ETDEWEB)

1993-06-01

The objective of this project was to develop an operational system for monitoring and inspection activities for waste storage facility operations at several DOE sites. Specifically, the product of this effort is a robotic device with enhanced intelligence and maneuverability capable of conducting routine inspection of stored waste drums. The device is capable of operating in narrow aisles and interpolating the free aisle space between rows of stacked drums. The system has an integrated sensor suite for leak detection, and is interfaced with a site database both for inspection planning and for data correlation, updating, and report generation. The system is capable of departing on an assigned mission, collecting required data, recording which positions of its mission had to be aborted or modified due to environmental constraints, and reporting back when the mission is complete. Successful identification of more than 90% of all drum defects has been demonstrated in a high fidelity waste storage facility mockup. Identified anomalies included rust spots, rust streaks, areas of corrosion, dents, and tilted drums. All drums were positively identified and correlated with the site database. This development effort is separated into three phases of which phase one is now complete. The first phase has demonstrated an integrated system for monitoring and inspection activities for waste storage facility operations. This demonstration system was quickly fielded and evaluated by leveraging technologies developed from previous NASA and DARPA contracts and internal research. The second phase will demonstrate a prototype system appropriate for operational use in an actual storage facility. The prototype provides an integrated design that considers operational requirements, hardware costs, maintenance, safety, and robustness. The final phase will demonstrate commercial viability using the prototype vehicle in a pilot waste operations and inspection project.

X-Ray, Digital Imaging with Volumetric Density Measurement and Profiling, Applied to the Characterization of Waste Drums

International Nuclear Information System (INIS)

Huhtiniemi, I.; Gupta, N.; Halliwell, S.

2006-01-01

The European Commission's Joint Research Centre Ispra Site (JRC-Ispra) has initiated a decommissioning and waste management program that will span about two decades. The program includes a requirement to characterize the contents of about 6,500 radioactive, 220 litre waste drums whose documented history is incomplete. To render the characterization process more efficient, the drums will be initially divided into homogeneous groups, an activity that will be based on existing documentation and non-destructive examination (NDE) by X-ray digital imaging. This paper describes the X-ray imaging techniques chosen, and the planned performance validation of the equipment. (authors)

Incremental cost-effectiveness of trauma service improvements for road trauma casualties: experience of an Australian major trauma centre.

Science.gov (United States)

Dinh, Michael M; Bein, Kendall J; Hendrie, Delia; Gabbe, Belinda; Byrne, Christopher M; Ivers, Rebecca

2016-09-01

Objective The aim of the present study was to estimate the cost-effectiveness of trauma service funding enhancements at an inner city major trauma centre. Methods The present study was a cost-effectiveness analysis using retrospective trauma registry data of all major trauma patients (injury severity score >15) presenting after road trauma between 2001 and 2012. The primary outcome was cost per life year gained associated with the intervention period (2007-12) compared with the pre-intervention period (2001-06). Incremental costs were represented by all trauma-related funding enhancements undertaken between 2007 and 2010. Risk adjustment for years of life lost was conducted using zero-inflated negative binomial regression modelling. All costs were expressed in 2012 Australian dollar values. Results In all, 876 patients were identified during the study period. The incremental cost of trauma enhancements between 2007 and 2012 totalled $7.91million, of which $2.86million (36%) was attributable to road trauma patients. After adjustment for important covariates, the odds of in-hospital mortality reduced by around half (adjusted odds ratio (OR) 0.48; 95% confidence interval (CI) 0.27, 0.82; P=0.01). The incremental cost-effectiveness ratio was A$7600 per life year gained (95% CI A$5524, $19333). Conclusion Trauma service funding enhancements that enabled a quality improvement program at a single major trauma centre were found to be cost-effective based on current international and Australian standards. What is known about this topic? Trauma quality improvement programs have been implemented across most designated trauma hospitals in an effort to improve hospital care processes and outcomes for injured patients. These involve a combination of education and training, the use of audit and key performance indicators. What does this paper add? A trauma quality improvement program initiated at an Australian Major Trauma Centre was found to be cost-effective over 12 years with

The Role of Cumulative Trauma, Betrayal, and Appraisals in Understanding Trauma Symptomatology.

Science.gov (United States)

Martin, Christina Gamache; Cromer, Lisa Demarni; Deprince, Anne P; Freyd, Jennifer J

2013-03-01

Poor psychological outcomes are common among trauma survivors, yet not all survivors experience adverse sequelae. The current study examined links between cumulative trauma exposure as a function of the level of betrayal (measured by the relational closeness of the survivor and the perpetrator), trauma appraisals, gender, and trauma symptoms. Participants were 273 college students who reported experiencing at least one traumatic event on a trauma checklist. Three cumulative indices were constructed to assess the number of different types of traumas experienced that were low (LBTs), moderate (MBTs), or high in betrayal (HBTs). Greater trauma exposure was related to more symptoms of depression, dissociation, and PTSD, with exposure to HBTs contributing the most. Women were more likely to experience HBTs than men, but there were no gender differences in trauma-related symptoms. Appraisals of trauma were predictive of trauma-related symptoms over and above the effects explained by cumulative trauma at each level of betrayal. The survivor's relationship with the perpetrator, the effect of cumulative trauma, and their combined impact on trauma symptomatology are discussed.

Aroma compounds and characteristics of noble-rot wines of Chardonnay grapes artificially botrytized in the vineyard.

Science.gov (United States)

Wang, Xing-Jie; Tao, Yong-Sheng; Wu, Yun; An, Rong-Yan; Yue, Zhuo-Ya

2017-07-01

Aroma characteristics and their impact volatile components of noble-rot wines elaborated from artificial botrytized Chardonnay grapes, obtained by spraying Botrytis cinerea suspension in Yuquan vineyard, Ningxia, China, were explored in this work. Dry white wine made from normal-harvested grapes and sweet wine produced from delay-harvested grapes were compared. Wine aromas were analysed by trained sensory panelists, and aroma compounds were determined by SPME-GC-MS. Results indicated that esters, fatty acids, thiols, lactones, volatile phenols and 2-nonanone increased markedly in noble-rot wines. In addition to typical aromas of noble-rot wines, artificial noble-rot wines were found to contain significant cream and dry apricot attributes. Partial Least-Squares Regression models of aroma characteristics against aroma components revealed that non-fermentative odorants were the primary contributor to dry apricot attribute, especially, thiols, C13-norisoprenoids, lactones, terpenols and phenolic acid derivatives, while cream attribute was dependent on both fermentative and non-fermentative volatile components. Copyright © 2017 Elsevier Ltd. All rights reserved.

Synthesis of Hydrophilic Sulfur-Containing Adsorbents for Noble Metals Having Thiocarbonyl Group Based on a Methacrylate Bearing Dithiocarbonate Moieties

Directory of Open Access Journals (Sweden)

Haruki Kinemuchi

2018-01-01

Full Text Available Novel hydrophilic sulfur-containing adsorbents for noble metals were prepared by the radical terpolymerization of a methacrylate bearing dithiocarbonate moieties (DTCMMA, hydrophilic monomers, and a cross-linker. The resulting adsorbents efficiently and selectively adsorbed noble metals (Au, Ag, and Pd from various multielement aqueous solutions at room temperature owing to the thiocarbonyl group having high affinity toward noble metals. The metal adsorption by the adsorbents was proceeded by simple mixing followed by filtration. The noble metal selectivity of the adsorbent obtained from DTCMMA and N-isopropylacrylamide was higher than that of the adsorbent obtained from DTCMMA and N,N-dimethylacrylamide due to the lower nonspecific adsorption.

The correlation between acoustic and magnetic properties in the long working metal boiler drum with the parameters of the electron microscope

Energy Technology Data Exchange (ETDEWEB)

Ababkov, Nikolai, E-mail: n.ababkov@rambler.ru; Smirnov, Alexander, E-mail: galvas.kem@gmail.com [T.F. Gorbachev Kuzbass State Technical University, Vesennjaja str 28, Kemerovo, 650000 Russian Federation (Russian Federation)

2016-01-15

The present paper presents comparative analysis of measurement results of acoustic and magnetic properties in long working metal of boiler drums and the results obtained by methods of electronic microscopy. The structure of the metal sample from the fracture zone to the base metal (metal working sample long) and the center of the base metal before welding (weld metal sample) was investigated by electron microscopy. Studies performed by spectral acoustic, magnetic noise and electron microscopic methods were conducted on the same plots and the same samples of long working and weld metal of high-pressure boiler drums. The analysis of research results showed high sensitivity of spectral-acoustic and magnetic-noise methods to definition changes of microstructure parameters. Practical application of spectral-acoustic and magnetic noise NDT method is possible for the detection of irregularities and changes in structural and phase state of the long working and weld metal of boiler drums, made of a special molybdenum steel (such as 20M). The above technique can be used to evaluate the structure and physical-mechanical properties of the long working metal of boiler drums in the energy sector.

Corrosion of steel drums containing immobilized ion exchange-resins and incineration ashes

International Nuclear Information System (INIS)

Marotta, F.; Schulz Rodriguez, F.M.; Farina, Silvia B.; Duffo, Gustavo S.

2009-01-01

The Argentine Atomic Energy Commission (CNEA) is responsible for developing the management nuclear waste disposal programme. This programme contemplates the design and construction of a facility for the final disposal of intermediate-level radioactive wastes. The proposed model is a near-surface monolithic repository similar to those in operation in El Cabril, Spain. The design of this type of repository is based on the use of multiple, independent and redundant barriers. The intermediate radioactive waste consists mostly in spent ionic exchange resins and filters from the nuclear power plants, research reactors and radioisotopes production facilities. The spent resins, as well as the incineration ashes, have to be immobilized before being stored to improve leach resistance of waste matrix and to maintain mechanical stability for safety requirements. Generally, cementation processes have been used as immobilization techniques for economical reasons as well as for being a simple operation. The immobilized resins and incineration ashes are thus contained in steel drums that, in turn, can undergo corrosion depending on the ionic content of the matrix. This work is a part of a systematic study of the corrosion susceptibility of steel drums in contact with immobilized cemented exchange-resins with different types and contents of aggressive species and incineration ashes. To this purpose, a special type of specimen was manufactured to simulate the cemented waste in the drum. The evolution of the corrosion potential and the corrosion current density of the steel, as well as the electrical resistivity of the matrix are being monitored along time. The aggressive species studied were chloride ions (the main ionic species present in nature) and sulphate ions (produced during the radiolysis process of the cationic exchange-resins after cementation). Preliminary results show the strong effect of chloride on the corrosion susceptibility of the steel. Monitoring will continue for

Noble Gases in the Hamlet Meteorite (LL4)

Science.gov (United States)

Amari, S.; Sabe, Y.; Shiraishi, T.; Matsuda, J.

2014-09-01

We analyzed noble gases in a bulk sample and an HF-HCl residue of Hamlet (LL4). The Xe composition of the residue shows that no diamond is contained in the residue. The 20Ne/22Ne ratio of Hamlet Ne-Q has been determined to be 11.0 ± 0.5.

Air water loop - an experimental facility to study thermal hydraulics of AHWR steam drum

International Nuclear Information System (INIS)

Bagul, R.K.; Pilkhwal, D.S.; Jain, V.; Vijayan, P.K.

2014-05-01

In the proposed Indian Advanced Heavy Water Reactor (AHWR) the coolant recirculation in the primary system is achieved by two-phase natural circulation. The two-phase steam-water mixture from the reactor core is separated in steam drum by gravity. Gravity separation of phases may lead to undesirable phenomena - carryover and carryunder. Carryover is the entrainment of liquid droplets in the vapor phase.Carryover needs to be minimized to avoid erosion corrosion of turbine blades. Carryunder is the entrainment of vapor bubbles with liquid flowing back to reactor core. Significant carryunder may in turn lead to reduced flow resulting in reduced CHF margin and stability in the coolant channel. An Air-Water Loop (AWL) has been designed to carry out the experiments relevant to AHWR steam drum. The design features and scaling philosophy is described in this report. (author)

Trauma Center Staffing, Infrastructure, and Patient Characteristics that Influence Trauma Center Need

Directory of Open Access Journals (Sweden)

Faul, Mark

2014-11-01

Full Text Available Introduction: The most effective use of trauma center resources helps reduce morbidity and mortality, while saving costs. Identifying critical infrastructure characteristics, patient characteristics and staffing components of a trauma center associated with the proportion of patients needing major trauma care will help planners create better systems for patient care.   Methods: We used the 2009 National Trauma Data Bank-Research Dataset to determine the proportion of critically injured patients requiring the resources of a trauma center within each Level I-IV trauma center (n=443. The outcome variable was defined as the portion of treated patients who were critically injured. We defined the need for critical trauma resources and interventions (“trauma center need” as death prior to hospital discharge, admission to the intensive care unit, or admission to the operating room from the emergency department as a result of acute traumatic injury. Generalized Linear Modeling (GLM was used to determine how hospital infrastructure, staffing Levels, and patient characteristics contributed to trauma center need.     Results: Nonprofit Level I and II trauma centers were significantly associated with higher levels of trauma center need. Trauma centers that had a higher percentage of transferred patients or a lower percentage of insured patients were associated with a higher proportion of trauma center need.  Hospital infrastructure characteristics, such as bed capacity and intensive care unit capacity, were not associated with trauma center need. A GLM for Level III and IV trauma centers showed that the number of trauma surgeons on staff was associated with trauma center need. Conclusion: Because the proportion of trauma center need is predominantly influenced by hospital type, transfer frequency, and insurance status, it is important for administrators to consider patient population characteristics of the catchment area when planning the

TiO2 structures doped with noble metals and/or graphene oxide to improve the photocatalytic degradation of dichloroacetic acid.

Science.gov (United States)

Ribao, Paula; Rivero, Maria J; Ortiz, Inmaculada

2017-05-01

Noble metals have been used to improve the photocatalytic activity of TiO 2 . Noble metal nanoparticles prevent charge recombination, facilitating electron transport due to the equilibration of the Fermi levels. Furthermore, noble metal nanoparticles show an absorption band in the visible region due to a high localized surface plasmon resonance (LSPR) effect, which contributes to additional electron movements. Moreover, systems based on graphene, titanium dioxide, and noble metals have been used, considering that graphene sheets can carry charges, thereby reducing electron-hole recombination, and can be used as substrates of atomic thickness. In this work, TiO 2 -based nanocomposites were prepared by blending TiO 2 with noble metals (Pt and Ag) and/or graphene oxide (GO). The nanocomposites were mainly characterized via transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier transformed infrared (FTIR), Raman spectroscopy, and photocurrent analysis. Here, the photocatalytic performance of the composites was analyzed via oxidizing dichloroacetic acid (DCA) model solutions. The influence of the noble metal load on the composite and the ability of the graphene sheets to improve the photocatalytic activity were studied, and the composites doped with different noble metals were compared. The results indicated that the platinum structures show the best photocatalytic degradation, and, although the presence of graphene oxide in the composites is supposed to enhance their photocatalytic performance, graphene oxide does not always improve the photocatalytic process. Graphical abstract It is a schematic diagram. Where NM is Noble Metal and LSPR means Localized Surface Plasmon Resonance.

Characterizing and improving passive-active shufflers for assays of 208-Liter waste drums

International Nuclear Information System (INIS)

Rinard, P.M.; Adams, E.L.; Menlove, H.O.; Sprinkle, J.K. Jr.

1992-01-01

A passive and active neutron shuffler for 208-L waste drums has been used to perform over 1500 active and 500 passive measurements on uranium and plutonium samples in 28 different matrices. The shuffler is now better characterized and improvements have been implemented or suggested. An improved correction for the effects of the matrix material was devised from flux-monitor responses. The most important cause of inaccuracies in assays is a localized instead of a uniform distribution of fissile material in a drum; a technique for deducing the distribution from the assay data and then applying a correction is suggested and will be developed further. A technique is given to detect excessive amounts of moderator that could make hundreds of grams of 235 U assay as zero grams. Sensitivities (minimum detectable masses) for 235 U with active assays and for 240 Pu eff with passive assays are presented and the effects of moderators and absorbers on sensitivities noted

Gamma-ray spectrometry method used for radioactive waste drums characterization for final disposal at National Repository for Low and Intermediate Radioactive Waste--Baita, Romania.

Science.gov (United States)

Done, L; Tugulan, L C; Dragolici, F; Alexandru, C

2014-05-01

The Radioactive Waste Management Department from IFIN-HH, Bucharest, performs the conditioning of the institutional radioactive waste in concrete matrix, in 200 l drums with concrete shield, for final disposal at DNDR - Baita, Bihor county, in an old exhausted uranium mine. This paper presents a gamma-ray spectrometry method for the characterization of the radioactive waste drums' radionuclides content, for final disposal. In order to study the accuracy of the method, a similar concrete matrix with Portland cement in a 200 l drum was used. © 2013 The Authors. Published by Elsevier Ltd All rights reserved.

Deposition and characterization of noble metal onto surfaces of 304l stainless steel

International Nuclear Information System (INIS)

Contreras R, A.; Arganis J, C. R.; Aguilar T, J. A.; Medina A, A. L.

2010-10-01

Noble metal chemical addition (NMCA) plus hydrogen water chemistry is an industry-wide accepted approach for potential intergranular stress corrosion cracking mitigation of BWR internals components. NMCA is a method of applying noble metal onto BWR internals surfaces using reactor water as the transport medium that causes the deposition of noble metal from the liquid onto surfaces. In this work different platinum concentration solutions were deposited onto pre-oxidized surfaces of 304l steel at 180 C during 48 hr in an autoclave. In order to simulate the zinc water conditions, deposits of Zn and Pt-Zn were also carried out. The solutions used to obtain the deposits were: sodium hexahydroxyplatinate (IV), zinc nitrate hydrate and zinc oxide. The deposits obtained were characterized by scanning electron microscopy and X-ray diffraction. Finally, the electrochemical corrosion potential of pre-oxidized samples with Pt deposit were obtained and compared with the electrochemical corrosion potential of only pre-oxidized samples. (Author)

Integrated DWPF Melter System (IDMS) campaign report: The first two noble metals operations

International Nuclear Information System (INIS)

Hutson, N.D.; Zamecnik, J.R.; Smith, M.E.; Miller, D.H.; Ritter, J.A.

1991-01-01

The Integrated DWPF Melter System (IDMS) is designed and constructed to provide an engineering-scale representation of the DWPF melter and its associated feed preparation and off-gas systems. The facility is the first pilot-scale melter system capable of processing mercury, and flowsheet levels of halides and noble metals. In order to characterize the processing of noble metals (Pd, Rh, Ru, and Ag) on a large scale, the IDMS will be operated batchstyle for at least nine feed preparation cycles. The first two of these operations are complete. The major observation to date occurred during the second run when significant amounts of hydrogen were evolved during the feed preparation cycle. The runs were conducted between June 7, 1990 and March 8, 1991. This time period included nearly six months of ''fix-up'' time when forced air purges were installed on the SRAT MFT and other feed preparation vessels to allow continued noble metals experimentation

Biomimetic Synthesis of Gelatin Polypeptide-Assisted Noble-Metal Nanoparticles and Their Interaction Study

Science.gov (United States)

Liu, Ying; Liu, Xiaoheng; Wang, Xin

2011-12-01

Herein, the generation of gold, silver, and silver-gold (Ag-Au) bimetallic nanoparticles was carried out in collagen (gelatin) solution. It first showed that the major ingredient in gelatin polypeptide, glutamic acid, acted as reducing agent to biomimetically synthesize noble metal nanoparticles at 80°C. The size of nanoparticles can be controlled not only by the mass ratio of gelatin to gold ion but also by pH of gelatin solution. Interaction between noble-metal nanoparticles and polypeptide has been investigated by TEM, UV-visible, fluorescence spectroscopy, and HNMR. This study testified that the degradation of gelatin protein could not alter the morphology of nanoparticles, but it made nanoparticles aggregated clusters array (opposing three-dimensional α-helix folding structure) into isolated nanoparticles stabilized by gelatin residues. This is a promising merit of gelatin to apply in the synthesis of nanoparticles. Therefore, gelatin protein is an excellent template for biomimetic synthesis of noble metal/bimetallic nanoparticle growth to form nanometer-sized device.

An autonomous mobil robot to perform waste drum inspections

International Nuclear Information System (INIS)

Peterson, K.D.; Ward, C.R.

1994-01-01

A mobile robot is being developed by the Savannah River Technology Center (SRTC) Robotics Group of Westinghouse Savannah River company (WSRC) to perform mandated inspections of waste drums stored in warehouse facilities. The system will reduce personnel exposure and create accurate, high quality documentation to ensure regulatory compliance. Development work is being coordinated among several DOE, academic and commercial entities in accordance with DOE's technology transfer initiative. The prototype system was demonstrated in November of 1993. A system is now being developed for field trails at the Fernald site

Element distribution and noble gas isotopic abundances in lunar meteorite Allan Hills A81005

International Nuclear Information System (INIS)

Kraehenbuehl, U.; Eugster, O.; Niedermann, S.

1986-01-01

Antarctic meteorite ALLAN HILLS A81005, an anorthositic breccia, is recognized to be of lunar origin. The noble gases in this meteorite were analyzed and found to be solar-wind implanted gases, whose absolute and relative concentrations are quite similar to those in lunar regolith samples. A sample of this meteorite was obtained for the analysis of the noble gas isotopes, including Kr(81), and for the determination of the elemental abundances. In order to better determine the volume derived from the surface correlated gases, grain size fractions were prepared. The results of the instrumental measurements of the gamma radiation are listed. From the amounts of cosmic ray produced noble gases and respective production rates, the lunar surface residence times were calculated. It was concluded that the lunar surface time is about half a billion years

Specialist bees collect Asteraceae pollen by distinctive abdominal drumming (Osmia) or tapping (Melissodes, Svastra)

Science.gov (United States)

Four species of western US Osmia (Cephalosmia) bees that are Asteraceae specialists (oligoleges) were observed to employ a heretofore unappreciated, stereotypical means of collecting pollen, abdominal drumming, to gather pollen from 19 flowering species representing nine tribes of Asteraceae. Abdom...

The Impact of Group Drumming on Social-Emotional Behavior in Low-Income Children

Directory of Open Access Journals (Sweden)

Ping Ho

2011-01-01

Full Text Available Low-income youth experience social-emotional problems linked to chronic stress that are exacerbated by lack of access to care. Drumming is a non-verbal, universal activity that builds upon a collectivistic aspect of diverse cultures and does not bear the stigma of therapy. A pretest-post-test non-equivalent control group design was used to assess the effects of 12 weeks of school counselor-led drumming on social-emotional behavior in two fifth-grade intervention classrooms versus two standard education control classrooms. The weekly intervention integrated rhythmic and group counseling activities to build skills, such as emotion management, focus and listening. The Teacher’s Report Form was used to assess each of 101 participants (n = 54 experimental, n = 47 control, 90% Latino, 53.5% female, mean age 10.5 years, range 10–12 years. There was 100% retention. ANOVA testing showed that intervention classrooms improved significantly compared to the control group in broad-band scales (total problems (P < .01, internalizing problems (P < .02, narrow-band syndrome scales (withdrawn/depression (P < .02, attention problems (P < .01, inattention subscale (P < .001, Diagnostic and Statistical Manual of Mental Disorders-oriented scales (anxiety problems (P < .01, attention deficit/hyperactivity problems (P < .01, inattention subscale (P < .001, oppositional defiant problems (P < .03, and other scales (post-traumatic stress problems (P < .01, sluggish cognitive tempo (P < .001. Participation in group drumming led to significant improvements in multiple domains of social-emotional behavior. This sustainable intervention can foster positive youth development and increase student-counselor interaction. These findings underscore the potential value of the arts as a therapeutic tool.

One parameter model potential for noble metals

International Nuclear Information System (INIS)

Idrees, M.; Khwaja, F.A.; Razmi, M.S.K.

1981-08-01

A phenomenological one parameter model potential which includes s-d hybridization and core-core exchange contributions is proposed for noble metals. A number of interesting properties like liquid metal resistivities, band gaps, thermoelectric powers and ion-ion interaction potentials are calculated for Cu, Ag and Au. The results obtained are in better agreement with experiment than the ones predicted by the other model potentials in the literature. (author)

PRODUKSI DEKSTRIN UBIKAYU MELALUI METODE GELATINISASI SEBAGIAN MENGGUNAKAN ROTARY DRUM

Directory of Open Access Journals (Sweden)

Surfiana Surfiana

2013-07-01

Full Text Available This research was aimed to obtain the optimum  condition and characteristics of  dextrin processed  from tapioca(cassava starch by using partial gelatinization using  drum dryer. This experiment was arranged in randomized compelete block design with three factors and three replications. The first factor was (V cassava varieties, which consisted of Cassesart/UJ-5 (V1 and Thailand/UJ-3  (V2. The second factor (K was the concentration which consisted of three levels : 30 % (K1, 35 % (K2, and 40 % (K3. The third factor (T was the temperature of the partial gelatinization which consisted of three temperature levels that were 80o C (T1, 90oC(T2, and 100oC(T3. Characterization was conducted on dextrin  processed from tapioca  included chemical and physical characteristics (water absorption, and water solubility. The results showed that the varieties of cassava, concentration, and temperature have significant effect on dextrin saccharide composition, solubility in water, and swelling power.  Thailand variety, 35 % concentration, and processing temperature of    90o C  produced dextrin with better functional characteristics , which were  24 % of dextrin composition, 77,15 % of solubility, and 6,89 %  of swelling power. Key words : Cassava, dextrin, parsial gelatinazation, rotary drum.

Noble gas studies in vapor-growth diamonds: Comparison with shock-produced diamonds and the origin of diamonds in ureilites

Energy Technology Data Exchange (ETDEWEB)

Matsuda, Junichi; Fukunaga, Kazuya; Ito, Keisuke (Kobe Univ. (Japan))

1991-07-01

The authors synthesized vapor-trowth diamonds by two kinds of Chemical Vapor Deposition (CVD) using microwave (MWCVD) and hot filament (HFCVD) ionization of gases, and examined elemental abundances and isotopic compositions of the noble gases trapped in the diamonds. It is remarkable that strong differences existed in the noble gas concentrations in the two kinds of CVD diamonds: large amounts of noble gases were trapped in the MWCVD diamonds, but not in the HFCVD diamonds. The heavy noble gases (Ar to Xe) in the MWCVD diamonds were highly fractionated compared with those in the ambient atmosphere, and are in good agreement with the calculated fractionation patterns for plasma at an electron temperature of 7,000-9,000 K. These results strongly suggest that the trapping mechanism of noble gases in CVD diamonds is ion implantation during diamond growth. The degrees of fractionation of heavy noble gases were also in good agreement with those in ureilites. The vapor-growth hypothesis is discussed in comparison with the impact-shock hypothesis as a better model for the origin of diamonds in ureilites. The diamond (and graphite, amorphous carbon, too) may have been deposited on early condensates such as Re, Ir, W, etc. This model explains the chemical features of vein material in ureilites; the refractory siderophile elements are enriched in carbon and noble gases and low in normal siderophiles. The vapor-growth model is also compatible with the oxygen isotopic data of ureilites which suggests that nebular processes are primarily responsible for the composition of ureilites.

The role of the trauma nurse leader in a pediatric trauma center.

Science.gov (United States)

Wurster, Lee Ann; Coffey, Carla; Haley, Kathy; Covert, Julia

2009-01-01

The trauma nurse leader role was developed by a group of trauma surgeons, hospital administrators, and emergency department and trauma leaders at Nationwide Children's Hospital who recognized the need for the development of a core group of nurses who provided expert trauma care. The intent was to provide an experienced group of nurses who could identify and resolve issues in the trauma room. Through increased education, exposure, mentoring, and professional development, the trauma nurse leader role has become an essential part of the specialized pediatric trauma care provided at Nationwide Children's Hospital.

The trauma ecosystem: The impact and economics of new trauma centers on a mature statewide trauma system.

Science.gov (United States)

Ciesla, David J; Pracht, Etienne E; Leitz, Pablo T; Spain, David A; Staudenmayer, Kristan L; Tepas, Joseph J

2017-06-01

Florida serves as a model for the study of trauma system performance. Between 2010 and 2104, 5 new trauma centers were opened alongside 20 existing centers. The purpose of this study was to explore the impact of trauma system expansion on system triage performance and trauma center patients' profiles. A statewide data set was queried for all injury-related discharges from adult acute care hospitals using International Classification of Diseases, Ninth Revision (ICD-9) codes for 2010 and 2014. The data set, inclusion criteria, and definitions of high-risk injury were chosen to match those used by the Florida Department of Health in its trauma registry. Hospitals were classified as existing Level I (E1) or Level II (E2) trauma centers and new E2 (N2) centers. Five N2 centers were established 11.6 to 85.3 miles from existing centers. Field and overall trauma system triage of high-risk patients was less accurate with increased overtriage and no change in undertriage. Annual volume at N2 centers increased but did not change at E1 and E2 centers. In 2014, Patients at E1 and E2 centers were slightly older and less severely injured, while those at N2 centers were substantially younger and more severely injured than in 2010. The injured patient-payer mix changed with a decrease in self-pay and commercial patients and an increase in government-sponsored patients at E1 and E2 centers and an increase in self-pay and commercial patients with a decrease in government-sponsored patients at N2 centers. Designation of new trauma centers in a mature system was associated with a change in established trauma center demographics and economics without an improvement in trauma system triage performance. These findings suggest that the health of an entire trauma system network must be considered in the design and implementation of a regional trauma system. Therapeutic/care management study, level IV; epidemiological, level IV.

Trauma pattern in a level I east-European trauma center

Directory of Open Access Journals (Sweden)

Bogdan Stoica

2015-10-01

Conclusions: Our trauma pattern profile is similar to the one found in west-European countries, with a predominance of traffic-related injuries and falls. The severity and anatomical puzzle for trauma lesions were more complex secondary to motorcycle or bicycle-to-auto vehicles collisions. A trauma registry, with prospective enrollment of patients, is a very effective tool for constant improvements in trauma care.

49 CFR 393.47 - Brake actuators, slack adjusters, linings/pads and drums/rotors.

Science.gov (United States)

2010-10-01

... 49 Transportation 5 2010-10-01 2010-10-01 false Brake actuators, slack adjusters, linings/pads and..., slack adjusters, linings/pads and drums/rotors. (a) General requirements. Brake components must be... same size. (c) Slack adjusters. The effective length of the slack adjuster on each end of an axle must...

Noble Gases as tracers of fluid migration in the Haynesville shale and overlying strata

Science.gov (United States)

Byrne, D. J.; Barry, P. H.; Lawson, M.; Ballentine, C. J.

2017-12-01

Noble gases are ideal tracers of physical processes and fluid provenance in crustal systems. Due to their inert nature, they are unaffected by chemical alteration, redox, or biological phenomena that fractionate other geochemical tracers. Noble gas analysis has been used to quantify fluid provenance, interactions, and ages in petroleum systems [1,2], but the effects of hydrocarbon migration on noble gas signatures have not been directly observed. The Haynesville Shale (East Texas & Louisiana), is exploited commercially for unconventional shale gas, but also acts as the source-rock for overlying conventional reservoirs. We present noble gas isotope and abundance data in samples collected from 9 natural gas wells sourced from the Haynesville Shale, as well as 21 from reservoirs in the overlying Cotton Valley (n=7), Travis Peak (n=9), and James (n=5) groups. Using a stratigraphic model, we observe systematic changes in the noble gas signatures as the fluids migrate from the Haynesville source rock to the overlying conventional accumulations. Helium isotope ratios (3He/4He) are strongly radiogenic in the Haynesville and stratigraphically older conventional reservoirs, with the younger reservoirs showing evidence of a mantle helium input. Argon isotope ratios (40Ar/36Ar) are strongly correlated with high 3He/4He, suggesting a similar provenance for radiogenic 40Ar and mantle 3He. Concentrations of groundwater-derived 36Ar are consistently higher in the conventional reservoirs than in the Haynesville shale, reflecting the greater interaction with groundwater during migration. However, 20Ne/36Ar ratios are not significantly different, suggesting that solubility-dependent partitioning is not simply dependent on vertical or horizontal migration distance. Krypton and xenon abundances are higher than expected for groundwater in all samples, a phenomenon that has been observed in many other hydrocarbon accumulations [3]. The excess Xe/Kr ratio is highest in the Haynesville

Optical Properties and Immunoassay Applications of Noble Metal Nanoparticles

International Nuclear Information System (INIS)

Zhu, S.; Zhou, W.

2010-01-01

Noble metal, especially gold (Au) and silver (Ag) nanoparticles exhibit unique and tunable optical properties on account of their surface plasmon resonance (SPR). In this paper, we mainly discussed the theory background of the enhanced optical properties of noble metal nanoparticles. Mie theory, transfer matrix method, discrete dipole approximation (DDA) method, and finite-difference time domain (FDTD) method applied brute-force computational methods for different nanoparticles optical properties. Some important nanostructure fabrication technologies such as nanosphere lithography (NSL) and focused ion beam (FIB) are also introduced in this paper. Moreover, these fabricated nanostructures are used in the plasmonic sensing fields. The binding signal between the antibody and antigen, amyloid-derived diffusible ligands (ADDLs)-potential Alzheimer's disease (AD) biomarkers, and staphylococcal enterotoxin B (SEB) in nano-Moore per liter (nM) concentration level are detected by our designed nanobiosensor. They have many potential applications in the biosensor, environment protection, food security, and medicine safety for health, and so forth, fields.

Optical Properties and Immunoassay Applications of Noble Metal Nanoparticles

Directory of Open Access Journals (Sweden)

Shaoli Zhu

2010-01-01

Full Text Available Noble metal, especially gold (Au and silver (Ag nanoparticles exhibit unique and tunable optical properties on account of their surface plasmon resonance (SPR. In this paper, we mainly discussed the theory background of the enhanced optical properties of noble metal nanoparticles. Mie theory, transfer matrix method, discrete dipole approximation (DDA method, and finite-difference time domain (FDTD method applied brute-force computational methods for different nanoparticles optical properties. Some important nanostructure fabrication technologies such as nanosphere lithography (NSL and focused ion beam (FIB are also introduced in this paper. Moreover, these fabricated nanostructures are used in the plasmonic sensing fields. The binding signal between the antibody and antigen, amyloid-derived diffusible ligands (ADDLs-potential Alzheimer's disease (AD biomarkers, and staphylococcal enterotixn B (SEB in nano-Moore per liter (nM concentration level are detected by our designed nanobiosensor. They have many potential applications in the biosensor, environment protection, food security, and medicine safety for health, and so forth, fields.

AUTOMATIC CONTROL SYSTEM OF THE DRUM BOILER SUPERHEATED STEAM TEMPERATURE.

Directory of Open Access Journals (Sweden)

Juravliov A.A.

2006-04-01

Full Text Available The control system of the temperature of the superheated steam of the drum boiler is examined. Main features of the system are the PI-controller in the external control loop and introduction of the functional component of the error signal of the external control loop with the negative feedback of the error signal between the prescribed value of steam flowrate and the signal of the steam flowrate in the exit of the boiler in the internal control loop.

Flameless atomic absorption determination of noble metals after extraction by mixture of di-2-ethylhexyldithiophosphoric acid and n-octylaniline

International Nuclear Information System (INIS)

Yukhin, Yu.M.; Udalova, T.A.; Tsimbalist, V.G.; AN SSSR, Novosibirsk. Inst. Geologii i Geofiziki)

1985-01-01

A possibility of using the mixture of di-2-ethylhexyl dithiophosphoric acid (D2EHDTPA) and p-octylaniline (OA) (extractants of acid and basic character) for extraction atomic absorption determination of noble metals is studied. The mixture of D2EHDTPA with OA is shown to extract noble metals from hydrochloric acid solutions with distribution factors > 10 3 . An extraction atomic absorption method for determination of noble metals in copperbearing materials is suggested. The minimum determined contents of noble metals at the initial sample equal to 100 for gold, silver, platinum, palladium, rhodium and ruthenium make up (g/t) 0.0005, 0.0001, 0.015, 0.005, 0.002 and 0.015 respectively. Relative standard deviation constitutes Ssub(r)<0.2

The role of noble metals in electric melting of nuclear waste glass

International Nuclear Information System (INIS)

Roth, G.; Weisenburger, S.

1990-01-01

Electrical melting of nuclear waste glass in ceramic melters applies Joule heating, with the molten glass acting as the conductive medium. The local energy release inside the melt relieves from the restriction of external heat addition, allowing to scale up the melter to industrial units. Certainly, that principle makes the melter operation susceptible for changes of the electrical properties of the glass melt. Hence, the melt properties are required to be locally uniform and constant with time. Temporary fluctuations in the feed composition, however, are usually attenuated by the high retention times being in the order of a day and more. More essential for the melter operation are segregation effects occurring systematically. This behaviour can be observed in the case of the so-called noble metal elements Ruthenium, Palladium and Rhodium, belonging to the Platinum metal group. The subject of this paper is to describe the behaviour of the noble metals in electric melting and the problems they can contribute to. The discussion is based on detailed knowledge gained from PAMELA's LEWC processing and from large-scale vitrification of commercial-like waste simulate at INE/KfK. Finally, ways are indicated to solve the noble metal problem technically

Ultrasonography in trauma

DEFF Research Database (Denmark)

Weile, Jesper; Nielsen, Klaus; Primdahl, Stine C

2017-01-01

BACKGROUND: The Focused Assessment with Sonography in Trauma (FAST) protocol is considered beneficial in emergent evaluation of trauma patients with blunt or penetrating injury and has become integrated into the Advanced Trauma Life Support (ATLS) protocol. No guidelines exist as to the use...... of ultrasonography in trauma in Denmark. We aimed to determine the current use of ultrasonography for assessing trauma patients in Denmark. METHODS: We conducted a nation-wide cross-sectional investigation of ultrasonography usage in trauma care. The first phase consisted of an Internet-based investigation....... Twenty-one (95.5%) of the guidelines included and recommended FAST as part of trauma assessment. The recommended person to perform the examination was the radiologist in n = 11 (50.0%), the surgeon in n = 6 (27.3%), the anesthesiologist in n = 1 (4.5%), and unspecified in n = 3 (13.6%) facilities. FAST...

Facial trauma.

Science.gov (United States)

Peeters, N; Lemkens, P; Leach, R; Gemels B; Schepers, S; Lemmens, W

Facial trauma. Patients with facial trauma must be assessed in a systematic way so as to avoid missing any injury. Severe and disfiguring facial injuries can be distracting. However, clinicians must first focus on the basics of trauma care, following the Advanced Trauma Life Support (ATLS) system of care. Maxillofacial trauma occurs in a significant number of severely injured patients. Life- and sight-threatening injuries must be excluded during the primary and secondary surveys. Special attention must be paid to sight-threatening injuries in stabilized patients through early referral to an appropriate specialist or the early initiation of emergency care treatment. The gold standard for the radiographic evaluation of facial injuries is computed tomography (CT) imaging. Nasal fractures are the most frequent isolated facial fractures. Isolated nasal fractures are principally diagnosed through history and clinical examination. Closed reduction is the most frequently performed treatment for isolated nasal fractures, with a fractured nasal septum as a predictor of failure. Ear, nose and throat surgeons, maxillofacial surgeons and ophthalmologists must all develop an adequate treatment plan for patients with complex maxillofacial trauma.

Electron--noble-gas spin-flip scattering at low energy

International Nuclear Information System (INIS)

Walker, T.G.; Bonin, K.; Happer, W.

1987-01-01

The spin-exchange rates and spin-relaxation rates for thermal electrons colliding with noble-gas atoms are calculated using the orthogonalized-plane-wave approximation and via partial-wave analysis. The two techniques give similar results and are in order-of-magnitude agreement with the experimental rate in Ar

Noble gas atmospheric monitoring for international safeguards at reprocessing plants

International Nuclear Information System (INIS)

Nakhleh, C.W.; Poths, J.; Stanbro, W.D.; Perry, R.T. Jr.; Wilson, W.B.; Fearey, B.L.

1997-01-01

The use of environmental sampling is a major component of the improvements of International Atomic Energy Agency safeguards being carried out under Program 93+2. Nonradioactive noble gas isotopic measurements in the effluent stream of large reprocessing facilities may provide useful confirmatory information on the burnup and reactor type of the spent fuel undergoing reprocessing. The authors have taken and analyzed stack samples at an operating facility. The data show clear fission signals. The authors are currently applying a maximum-likelihood estimation procedure to determine the fuel burnup from these data. They anticipate that the general features involved in the table noble gas problem--selection of appropriate signals, measurement of those signals under realistic conditions, and inverse calculation of parameters of interest from the environmental data--will be present in all environmental sampling problems. These methods should therefore be widely applicable

Modeling impurity-assisted chain creation in noble-metal break junctions

International Nuclear Information System (INIS)

Di Napoli, S; Thiess, A; Blügel, S; Mokrousov, Y

2012-01-01

In this work we present the generalization of the model for chain formation in break junctions, introduced by Thiess et al (2008 Nano Lett. 8 2144), to zigzag transition-metal chains with s and p impurities. We apply this extended model to study the producibility trends for noble-metal chains with impurities, often present in break junction experiments, namely, Cu, Ag and Au chains with H, C, O and N adatoms. Providing the material-specific parameters for our model from systematic full-potential linearized augmented plane-wave first-principles calculations, we find that the presence of such impurities crucially affects the binding properties of the noble-metal chains. We reveal that both the impurity-induced bond strengthening and the formation of zigzag bonds can lead to a significantly enhanced probability for chain formation in break junctions. (paper)

Characterisation and radiolysis of modified lithium orthosilicate pebbles with noble metal impurities

DEFF Research Database (Denmark)

Tamulevičius, Sigitas; Zariņš, A.; Valtenbergs, O.

2017-01-01

Modified lithium orthosilicate (Li4SiO4) pebbles with additions of titanium dioxide (TiO2) are suggested as an alternative tritium breeding ceramic for the European solid breeder test blanket module. The noble metals – platinum (Pt), gold (Au) and rhodium (Rh), can be introduced into the modified...... Li4SiO4 pebbles during the melt-based process, due to the corrosion of Pt-Rh and Pt-Au alloy crucible components. In this study, the surface microstructure, chemical and phase composition of the modified Li4SiO4 pebbles with different contents of the noble metals was analysed. The influence...

Light-controlled relaxation of the rat penile corpus cavernosum using NOBL-1, a novel nitric oxide releaser

Directory of Open Access Journals (Sweden)

Yuji Hotta

2016-05-01

Full Text Available Purpose: To investigate whether relaxation of the rat penile corpus cavernosum could be controlled with NOBL-1, a novel, lightcontrollable nitric oxide (NO releaser. Materials and Methods: Fifteen-week-old male Wistar-ST rats were used. The penile corpus cavernosum was prepared and used in an isometric tension study. After noradrenaline (10−5 M achieved precontraction, the penile corpus cavernosum was irradiated by light (470–500 nm with and without NOBL-1 (10−6 M. In addition, we noted rats’ responses to light with vardenafil (10−6 M, a phosphodiesterase-5 (PDE-5 inhibitor. Next, responses to light in the presence of a guanylate cyclase inhibitor, ODQ (1H-[1,2,4] oxadiazolo[4,3-a]quinoxalin-1-one (10−5 M, were measured. All measurements were performed in pretreated L-NAME (10−4 M conditions to inhibit endogenous NO production. Results: Corpus cavernosal smooth muscle, precontracted with noradrenaline, was unchanged by light irradiation in the absence of NOBL-1. However, in the presence of NOBL-1, corpus cavernosal smooth muscle, precontracted with noradrenaline, relaxed in response to light irradiation. After blue light irradiation ceased, tension returned. In addition, the light response was obviously enhanced in the presence of a PDE-5 inhibitor. Conclusions: This study showed that rat corpus cavernosal smooth muscle relaxation can be light-controlled using NOBL-1, a novel, light sensitive NO releaser. Though further in vivo studies are needed to investigate possible usefulness, NOBL-1 may be prove to be a useful tool for erectile dysfunction therapy, specifically in the field of penile rehabilitation.

Non-noble metal fuel cell catalysts

CERN Document Server

Chen, Zhongwei; Zhang, Jiujun

2014-01-01

Written and edited by a group of top scientists and engineers in the field of fuel cell catalysts from both industry and academia, this book provides a complete overview of this hot topic. It covers the synthesis, characterization, activity validation and modeling of different non-noble metal and metalfree electrocatalysts for the reduction of oxygen, as well as their integration into acid or alkaline polymer exchange membrane (PEM) fuel cells and their performance validation, while also discussing those factors that will drive fuel cell commercialization. With its well-structured app

Noble gases and the early history of the Earth: Inappropriate paradigms and assumptions inhibit research and communication

Science.gov (United States)

Huss, G. R.; Alexander, E. C., Jr.

1985-01-01

The development of models as tracers of nobel gases through the Earth's evolution is discussed. A new set of paradigms embodying present knowledge was developed. Several important areas for future research are: (1) measurement of the elemental and isotopic compositions of the five noble gases in a large number of terrestrial materials, thus better defining the composition and distribution of terrestrial noble gases; (2) determinations of relative diffusive behavior, chemical behavior, and the distribution between solid and melt of noble gases under mantle conditions are urgently needed; (3) disequilibrium behavior in the nebula needs investigation, and the behavior of plasmas and possible cryotrapping on cold nebular solids are considered.

Electron shell contributions to gamma-ray spectra of positron annihilation in noble gases

Energy Technology Data Exchange (ETDEWEB)

Wang, Feng; Selvam, Lalitha [Centre for Molecular Simulation, Swinburne University of Technology, PO Box 218, Hawthorn, Victoria 3122 (Australia); Gribakin, Gleb F [Department of Applied Mathematics and Theoretical Physics, Queen' s University Belfast BT7 1NN (United Kingdom); Surko, Clifford M, E-mail: fwang@swin.edu.a [Physics Department, University of California, San Diego, La Jolla, CA 92093-0319 (United States)

2010-08-28

Gamma-ray positron annihilation spectra of the noble gases are simulated using computational chemistry tools for the bound electron wavefunctions and plane-wave approximation for the low-energy positron. The present annihilation line shapes, i.e. the full width at half maximum, {Delta}{epsilon}, of the {gamma}-ray annihilation spectra for He and Ar (valence) agree well with available independent atomic calculations using a different algorithm. For other noble gases they achieve moderate agreement with the experimental measurements. It is found that the contributions of various atomic electron shells to the spectra depend significantly on their principal quantum number n and orbital angular momentum quantum number l. The present study further reveals that the outermost ns electrons of the noble gases exhibit spectral line shapes in close agreement with those measured, indicating (as expected) that the measurements are not due to a simple sum over the momentum densities for all atomic electrons. The robust nature of the present approach makes it possible for us to proceed to more complex molecular systems using the tools of modern computational chemistry.

Application of drum compost and vermicompost to improve soil health, growth, and yield parameters for tomato and cabbage plants.

Science.gov (United States)

Goswami, Linee; Nath, Anil; Sutradhar, Sweety; Bhattacharya, Satya Sundar; Kalamdhad, Ajay; Vellingiri, Kowsalya; Kim, Ki-Hyun

2017-09-15

Utilization of different types of solid wastes through composting is important for environmental sustainability and restoring soil quality. Although drum composting is an efficient technology, the possibility of heavy metal contamination restricts its large-scale use. In this research, a field experiment was conducted to evaluate the impact of water hyacinth drum compost (DC) and traditional vermicompost (VC) on soil quality and crop growth in an agro-ecosystem cultivated intensively with tomato and cabbage as test crops. A substantial improvement in soil health was observed with respect to nutrient availability, physical stability, and microbial diversity due to the application of drum compost and traditional vermicompost. Moreover, soil organic carbon was enriched through increased humic and fulvic acid carbon. Interestingly, heavy metal contamination was less significant in vermicompost-treated soils than in those receiving the other treatments. The use of VC and DC in combination with recommended chemical fertilization effectively stimulated crop growth, yield, product quality, and storage longevity for both tomato and cabbage. Copyright © 2017 Elsevier Ltd. All rights reserved.

Percutaneous coronary intervention versus coronary artery bypass grafting: where are we after NOBLE and EXCEL?

Science.gov (United States)

Fortier, Jacqueline H; Shaw, Richard E; Glineur, David; Grau, Juan B

2017-11-01

The publication of the NOBLE and EXCEL trials, with seemingly conflicting results, brought into question whether percutaneous coronary intervention (PCI) or coronary artery bypass grafting (CABG) is better for low-risk patients with left main coronary artery stenosis (LMCAS). This review appraises the methods and results of NOBLE and EXCEL, contextualizes them within the literature, and determines how they may affect clinical practice. We appraised the trials and describe differences in methodology and results. NOBLE recruited primarily isolated LMCAS, and found that CABG was superior to PCI. EXCEL's population included patients LMCAS in the context of multivessel CAD, and found PCI and CABG were comparable. Both trials enrolled young patients with few comorbidities, and there was more protocol-mandated consistency in the procedural techniques and medical therapy of patients receiving PCI. The generalizability of these trials is limited by the use of young, healthy patients at highly skilled centres that rarely reflect typical clinical practice. If these studies are to maintain relevance, trialists must address the lack of protocolization of surgical interventions and inconsistent medical therapies. Unfortunately, the limitations of NOBLE and EXCEL mean that we are no closer to answering the question of what is the optimal treatment for patients with LMCAS.

Three dimensional reconstruction of activity profiles in 220 liters radioactive waste packages containing super-compacted 100 liters drums

International Nuclear Information System (INIS)

Van Velzen, L.P.M.; Maes, J.

2007-01-01

The 3DRedact project's main objective is the development of a non-destructive assay (NDA) system that can replace emission computer tomography (ECT) and transmission computer tomography (TCT) for the routine characterization of decayed radioactive waste 220 liters drums. The existing fast NDA scan system has been extended with a transmission system that fulfils the requirements of fast scan measurements. The design parameters and engineering are described. As a consequence of this extension the analyze program HOLIS had to be updated, so that HOLIS can make full advantage of the transmission data generated by the analysis of a 220 liters waste drum, containing different super compacted drums. The achievements of the new HOLIS version are presented. As a first assessment, based on the presented tests results, the accuracy of the calculated coordinates of hotspots can be assessed for all coordinates ± 1 cm and for the activity of the hot-spot ± 5 %. These accuracies are within the predefined requirements e.g. coordinates uncertainty ± 2 cm and activity less than 10 %. Further, additional safety systems have been installed to improve a healthy and save working environment. (authors)

Larval Red Drum (Sciaenops ocellatus) Sublethal Exposure to Weathered Deepwater Horizon Crude Oil: Developmental and Transcriptomic Consequences.

Science.gov (United States)

Xu, Elvis Genbo; Khursigara, Alex J; Magnuson, Jason; Hazard, E Starr; Hardiman, Gary; Esbaugh, Andrew J; Roberts, Aaron P; Schlenk, Daniel

2017-09-05

The Deepwater Horizon (DWH) incident resulted in extensive oiling of the pelagic zone and shoreline habitats of many commercially important fish species. Exposure to the water-accommodated fraction (WAF) of oil from the spill causes developmental toxicity through cardiac defects in pelagic fish species. However, few studies have evaluated the effects of the oil on near-shore estuarine fish species such as red drum (Sciaenops ocellatus). Following exposure to a certified weathered slick oil (4.74 μg/L ∑PAH 50 ) from the DWH event, significant sublethal impacts were observed ranging from impaired nervous system development [average 17 and 22% reductions in brain and eye area at 48 h postfertilization (hpf), respectively] to abnormal cardiac morphology (100% incidence at 24, 48, and 72 hpf) in red drum larvae. Consistent with the phenotypic responses, significantly differentially expressed transcripts, enriched gene ontology, and altered functions and canonical pathways predicted adverse outcomes in nervous and cardiovascular systems, with more pronounced changes at later larval stages. Our study demonstrated that the WAF of weathered slick oil of DWH caused morphological abnormalities predicted by a suite of advanced bioinformatic tools in early developing red drum and also provided the basis for a better understanding of molecular mechanisms of crude oil toxicity in fish.

Noble gas confinement for reactor fuel melting accidents

International Nuclear Information System (INIS)

Monson, P.R.

1984-01-01

In the unlikely event of a fuel melting accident, radioactive material would be released into the reactor room. This radioactive material would consist of particulate matter, iodine, tritium, and the noble gases krypton and xenon. In the case of reactors with containment domes the gases would be contained for subsequent cleanup. For reactors without contaiment the particulates and the iodine can be effectively removed with HEPA and carbon filters of current technology; however, noble gases cannot be easily removed and would be released to the atmosphere. In either case, it would be highly desirable to have a system that could be brought online to treat this contaminated air to minimize the population dose. A low temperature adsorption system has been developed at the Savannah River Laboratory to remove the airborne radioactive material from such a fuel melting accident. Over two dozen materials have been tested in extensive laboratory studies, and hydrogen mordenite and silver mordenite were found to be the most promising adsorbents. A full-scale conceptual design has also been developed. Results of the laboratory studies and the conceptual design are discussed along with plans for further development of this concept

Noble gas confinement for reactor fuel melting accidents

International Nuclear Information System (INIS)

Monson, P.R.

1985-01-01

In the unlikely event of a fuel melting accident radioactive material would be released into the reactor room. This radioactive material would consist of particulate matter, iodine, tritium, and the noble gases krypton and xenon. In the case of reactors with containment domes, the gases would be contained for subsequent cleanup. For reactors without containment the particulates and the iodine can be effectively removed with HEPA and carbon filters of current technology; however, noble gases cannot be easily removed and would be released to the atmosphere. In either case, it would be highly desirable to have a system that could be brought online to treat this contaminated air to minimize the population dose. A low temperature adsorption system has been developed at the Savannah River Laboratory to remove the airborne radioactive material from such a fuel melting accident. Over two dozen materials have been tested in extensive laboratory studies, and hydrogen mordensite and silver mordenite were found to be the most promising absorbents. A full-scale conceptual design has also been developed. Results of the laboratory studies and the conceptual design will be discussed along with plans for further development of this concept

Isotopic and noble gas geochemistry in geothermal research

Energy Technology Data Exchange (ETDEWEB)

Kennedy, B.M.; DePaolo, D.J. [Lawrence Berkeley National Lab., CA (United States)

1997-12-31

The objective of this program is to provide, through isotopic analyses of fluids, fluid inclusions, and rocks and minerals coupled with improved methods for geochemical data analysis, needed information regarding sources of geothermal heat and fluids, the spatial distribution of fluid types, subsurface flow, water-rock reaction paths and rates, and the temporal evolution of geothermal systems. Isotopic studies of geothermal fluids have previously been limited to the light stable isotopes of H, C, and O. However, other isotopic systems such as the noble gases (He, Ne, Ar, Kr and Xe) and reactive elements (e.g. B, N, S, Sr and Pb) are complementary and may even be more important in some geothermal systems. The chemistry and isotopic composition of a fluid moving through the crust will change in space and time in response to varying chemical and physical parameters or by mixing with additional fluids. The chemically inert noble gases often see through these variations, making them excellent tracers for heat and fluid sources. Whereas, the isotopic compositions of reactive elements are useful tools in characterizing water-rock interaction and modeling the movement of fluids through a geothermal reservoir.

The differential dieaway technique applied to the measurement of the fissile content of drums of cement encapsulated waste

International Nuclear Information System (INIS)

Swinhoe, M.T.

1986-01-01

This report describes calculations of the differential dieaway technique as applied to cement encapsulated waste. The main difference from previous applications of the technique are that only one detector position is used (diametrically opposite the neutron source) and the chamber walls are made of concrete. The results show that by rotating the drum the response to fissile material across the central plane of the drum can be made relatively uniform. The absolute size of the response is about 0.4. counts per minute per gram fissile for a neutron source of 10 8 neutrons per second. Problems of neutron and gamma background and water content are considered. (author)

Trauma facilities in Denmark

DEFF Research Database (Denmark)

Weile, Jesper; Nielsen, Klaus; Primdahl, Stine C

2018-01-01

Background: Trauma is a leading cause of death among adults aged challenge. Evidence supports the centralization of trauma facilities and the use multidisciplinary trauma teams. Because knowledge is sparse on the existing distribution of trauma facilities...... and the organisation of trauma care in Denmark, the aim of this study was to identify all Danish facilities that care for traumatized patients and to investigate the diversity in organization of trauma management. Methods: We conducted a systematic observational cross-sectional study. First, all hospitals in Denmark...... were identified via online services and clarifying phone calls to each facility. Second, all trauma care manuals on all facilities that receive traumatized patients were gathered. Third, anesthesiologists and orthopedic surgeons on call at all trauma facilities were contacted via telephone...

The Role of Cumulative Trauma, Betrayal, and Appraisals in Understanding Trauma Symptomatology

OpenAIRE

Martin, Christina Gamache; Cromer, Lisa DeMarni; DePrince, Anne P.; Freyd, Jennifer J.

2011-01-01

Poor psychological outcomes are common among trauma survivors, yet not all survivors experience adverse sequelae. The current study examined links between cumulative trauma exposure as a function of the level of betrayal (measured by the relational closeness of the survivor and the perpetrator), trauma appraisals, gender, and trauma symptoms. Participants were 273 college students who reported experiencing at least one traumatic event on a trauma checklist. Three cumulative indices were const...

Noble gases in ten stone meteorites from Antarctica

International Nuclear Information System (INIS)

Weber, H.W.; Schultz, L.

1980-01-01

The concentrations and isotopic composition of noble gases have been determined in all ten stone meteorites recovered in Antarctica during 1976-1977 by a U.S.-Japanese expedition. From a comparison of spallogenic and radiogenic gas components it is concluded that the chondrites Mt. Baldr (a) and Mt. Baldr (b) belong to the same fall but that all other stone meteorites are individual finds. (orig.)

Influence de l'énergie de surface d'un tambour deshuileur sur son efficacité de relevage Influence of the Surface Energy of a Deoiling Drum on Its Gathering Efficiency

Directory of Open Access Journals (Sweden)

Aurelle Y.

2006-11-01

Full Text Available Au cours de cette étude est analysée l'influence de l'énergie de surface d'un tambour déshuileur sur son efficacité et sa sélectivité de relevage. Quatre tambours en acier inoxydable, en polychlorure de vinyle, en polypropylène et en dérivé fluorocarboné de tensions critiques de mouillage différentes sont testés comparativement en fonction de l'histoire de leur expositionvis-à-vis de phases hydrocarbure (kérosène et eau. Les essais réalisés montrent que seuls les tambours en dérivé fluorocarboné de très faible tension critique de mouillage s'avèrent intéressants pour des utilisations industrielles. En effet, ils présentent un comportement indépendant de l'histoire de leur exposition ce qui les rend très faciles à utiliser, sans précautions particulières, du fait de leur très grande sélectivité vis-à-vis des hydrocarbures. Par contre, les autres tambours, qui présentent des contributions polaires non négligeables à leur énergie de surface, ont des comportements vis-à-vis des hydrocarbures fonction de l'histoire de leur exposition et ne s'avèrent pas sélectifs vis-à-vis des hydrocarbures à récupérer. The aim of this article is to analyze the influence of the surface energy of a deoiling drum on its gathering efficiency and selectivity. The project consists in testing drums having the same size but made of materials having different surface energies so as to evaluate the influence of this key parameter that had previously been poorly analyzed. Four materials were chosen : stainless steel, polyvinyl chloride, polypropylene, and a fluorocarbon derivative. These materials are representative, a priori, of the behavior of most materials because of the position of their critical wetting tension (gamma c compared to the superficial tension values of water (72 dyn/cm and the hydrocarbon phases to be gathered (25 to 35 dyn/cm (Fig. 1. It should be noted that the fluorocarbon derivative drum tested was patented by

Artificial companions as personal coach for children: The Interactive Drums Teacher

OpenAIRE

Courgeon , Matthieu; Duhaut , Dominique

2015-01-01

International audience; The MOCA Project that aims at designing and studying the interaction and relationship between artificial companions and children in everyday life at home activities. Artificial companions are digital embodied entities that can be either robotic or virtual. In this paper, we focus on a single activity, subpart of the whole project: a coaching application that uses two artificial companions to teach the basics of drums to children. One device is a Nao robot, the other is...

Attosecond Time Delay in Photoionization of Noble-Gas and Halogen Atoms

Directory of Open Access Journals (Sweden)

Liang-Wen Pi

2018-02-01

Full Text Available Ultrafast processes are now accessible on the attosecond time scale due to the availability of ultrashort XUV laser pulses. Noble-gas and halogen atoms remain important targets due to their giant dipole resonance and Cooper minimum. Here, we calculate photoionization cross section, asymmetry parameter and Wigner time delay using the time-dependent local-density approximation (TDLDA, which includes the electron correlation effects. Our results are consistent with experimental data and other theoretical calculations. The asymmetry parameter provides an extra layer of access to the phase information of the photoionization processes. We find that halogen atoms bear a strong resemblance on cross section, asymmetry parameter and time delay to their noble-gas neighbors. Our predicted time delay should provide a guidance for future experiments on those atoms and related molecules.

Geriatric trauma.

Science.gov (United States)

Adams, Sasha D; Holcomb, John B

2015-12-01

The landscape of trauma is changing due to an aging population. Geriatric patients represent an increasing number and proportion of trauma admissions and deaths. This review explores recent literature on geriatric trauma, including triage criteria, assessment of frailty, fall-related injury, treatment of head injury complicated by coagulopathy, goals of care, and the need for ongoing education of all surgeons in the care of the elderly. Early identification of high-risk geriatric patients is imperative to initiate early resuscitative efforts. Geriatric patients are typically undertriaged because of their baseline frailty being underappreciated; however, centers that see more geriatric patients do better. Rapid reversal of anticoagulation is important in preventing progression of brain injury. Anticipation of difficult disposition necessitates early involvement of physical therapy for rehabilitation and case management for appropriate placement. Optimal care of geriatric trauma patients will be based on the well established tenets of trauma resuscitation and injury repair, but with distinct elements that address the physiological and anatomical challenges presented by geriatric patients.

Seawater corrosion tests for low-level radioactive waste drum containers

International Nuclear Information System (INIS)

Maeda, Sho; Wadachi, Yoshiki

1985-11-01

This report is a part of corrosion tests of drums under various environmental conditions (seawater, river water, coastal sand, inland soil and indoor and outdoor atmosphere) done at Japan Atomic Energy Research Institute sponsored by the Science and Technology Agency. The corrosion tests were started in November, 1977 and complated at March, 1984. This report describes the results of the seawater corrosion tests which are part of the final report, ''Corrosion Safety Demonstration Test'' (Japanese), and it is expected to contribute the safety assessment of sea dumping of low-level radioactive waste packages. (author)

Volatile elements - water, carbon, nitrogen, noble gases - on Earth

Science.gov (United States)

Marty, B.

2017-12-01

Understanding the origin and evolution of life-bearing volatile elements (water, carbon, nitrogen) on Earth is a fruitful and debated area of research. In his pioneering work, W.W. Rubey inferred that the terrestrial atmosphere and the oceans formed from degassing of the mantle through geological periods of time. Early works on noble gas isotopes were consistent with this view and proposed a catastrophic event of mantle degassing early in Earth's history. We now have evidence, mainly from noble gas isotopes, that several cosmochemical sources contributed water and other volatiles at different stages of Earth's accretion. Potential contributors include the protosolar nebula gas that equilibrated with magma oceans, inner solar system bodies now represented by chondrites, and comets. Stable isotope ratios suggest volatiles where primarily sourced by planetary bodies from the inner solar system. However, recent measurements by the European Space Agency Rosetta probe on the coma of Comet 67P/Churyumov-Gerasimenko permit to set quantitative constraints on the cometary contribution to the surface of our planet. The surface and mantle reservoirs volatile elements exchanged volatile elements through time, with rates that are still uncertain. Some mantle regions remained isolated from whole mantle convection within the first tens to hundreds million years after start of solar system formation. These regions, now sampled by some mantle plumes (e.g., Iceland, Eifel) preserved their volatile load, as indicated by extinct and extant radioactivity systems. The abundance of volatile elements in the mantle is still not well known. Different approaches, such as high pressure experimental petrology, noble gas geochemistry, modelling, resulted in somewhat contrasted estimates, varying over one order of magnitude for water. Comparative planetology, that is, the study of volatiles on the Moon, Venus, Mars, Vesta, will shed light on the sources and strengths of these elements in the

A review of noble gas geochemistry in relation to early Earth history

Science.gov (United States)

Kurz, M. D.

1985-01-01

One of the most fundamental noble gas constraints on early Earth history is derived from isotopic differences in (129)Xe/(130)Xe between various terrestrial materials. The short half life (17 m.y.) of extinct (129I, parent of (129)Xe, means that these differences must have been produced within the first 100 m.y. after terrestrial accretion. The identification of large anomalies in (129)Xe/(130)Xe in mid ocean ridge basalts (MORB), with respect to atmospheric xenon, suggests that the atmosphere and upper mantle have remained separate since that time. This alone is a very strong argument for early catastrophic degassing, which would be consistent with an early fractionation resulting in core formation. However, noble gas isotopic systematics of oceanic basalts show that the mantle cannot necessarily be regarded as a homogeneous system, since there are significant variations in (3)He/(4)He, (40)Ar/(36)Ar, and (129)Xe/(130)Xe. Therefore, the early degassing cannot be considered to have acted on the whole mantle. The specific mechanisms of degassing, in particular the thickness and growth of the early crust, is an important variable in understanding present day noble gas inventories. Another constraint can be obtained from rocks that are thought to be derived from near the lithosphere asthenosphere boundary: ultramafic xenoliths.

The drug-minded protein interaction database (DrumPID) for efficient target analysis and drug development.

Science.gov (United States)

Kunz, Meik; Liang, Chunguang; Nilla, Santosh; Cecil, Alexander; Dandekar, Thomas

2016-01-01

The drug-minded protein interaction database (DrumPID) has been designed to provide fast, tailored information on drugs and their protein networks including indications, protein targets and side-targets. Starting queries include compound, target and protein interactions and organism-specific protein families. Furthermore, drug name, chemical structures and their SMILES notation, affected proteins (potential drug targets), organisms as well as diseases can be queried including various combinations and refinement of searches. Drugs and protein interactions are analyzed in detail with reference to protein structures and catalytic domains, related compound structures as well as potential targets in other organisms. DrumPID considers drug functionality, compound similarity, target structure, interactome analysis and organismic range for a compound, useful for drug development, predicting drug side-effects and structure-activity relationships.Database URL:http://drumpid.bioapps.biozentrum.uni-wuerzburg.de. © The Author(s) 2016. Published by Oxford University Press.

Trauma Africa

Directory of Open Access Journals (Sweden)

Victor Y. Kong

2013-11-01

Full Text Available “Major Trauma. Dr. Kong, please come to the Trauma Unit immediately. Dr. Kong, please come to the Trauma Unit immediately.” Even though I have been working at Edendale Hospital as a trauma registrar for over a year, whenever I hear this announcement over the hospital intercom system, my heart beats just a little faster than normal. When I first arrived at Edendale my colleagues told me that the adrenaline rush I would experience after being called out to attend a new emergency would decrease over time, and indeed they were right. However, it is also true to say that on some occasions more than others, it is still felt more strongly than ever.

Modification of titanium electrodes by a noble metal deposit

Energy Technology Data Exchange (ETDEWEB)

Devilliers, D.; Mahe, E. [Pierre et Marie Curie Univ., Paris (France). Laboratoire LI2C, UMR CNRS

2008-07-01

Titanium is commonly used as a substrate for dimensionally stable anodes (DSAs) because it is corrosion-resistant in acid media and because a passive titanium oxide (TiO2) film can be formed on the surface. This paper reported on a study in which titanium substrates were first covered by anodization with a TiO2 layer. The electrochemical properties of the Ti/TiO2 electrodes were investigated. The modification of the substrates by cathodic electrodeposition of a noble metal was described. The reactivity of the Ti/TiO2/Pt structures were illustrated by impedance spectroscopy experiments. The impedance studies performed with Ti/ TiO2 electrodes in the presence of a redox couple in solution (Fe3+/Fe2+ system in sulphuric acid) showed that the electronic transfer is very slow. It was concluded that the deposition of a noble metal coating on Ti/TiO2 substrates leads to modified titanium electrodes that exhibit electrocatalytic behaviour versus specific electrochemical reactions. 1 ref., 3 figs.

Portrayals of men and women in Drum magazine (South Africa advertisements

Directory of Open Access Journals (Sweden)

Mlenga Jere

2014-07-01

Full Text Available Orientation: The subject of gender portrayals in advertising continues to generate academicdiscussions in part because of its socialisation effects. Research purpose: The purpose of this study is to determine how print advertisements inDrum magazine portray women and men based on a number of categories including traitdescriptors, physical characteristics, role behaviours and occupational status. Motivation for the study: It is important to understand gender portrayals in advertisingbecause perceptions of social reality are influenced by what people are exposed to insocialisation agents such as advertisements. Research approach, design and method: A quantitative content analysis was run on a sampleof 415 advertisements drawn from Drum magazine. Partial least squares analysis was used toassess the relationships between the variables.Main findings: The findings show that gender has a statistically significant effect on profiles(roles and sexual appeal but not on gender equity. Advertisers therefore treat modelsdifferently with regard to the roles assigned and the use of sexual appeal. Practical/managerial implications: Previous research evidence and theory indicate that thecontent of advertisements does influence readers’ self-perception and also their perceptionof others. Within the bounds of advertising creativity, it is important that advertisers payparticular attention to gender portrayals in advertising to avoid the creation or perpetuationof gender stereotypes. Contribution/value-add: Though the model’s gender influences portrayals in advertising,other contextual factors are also important determinants of portrayals.

Preliminary investigation of a technique to separate fission noble metals from fission-product mixtures

International Nuclear Information System (INIS)

Mellinger, G.B.; Jensen, G.A.

1982-08-01

A variation of the gold-ore fire assay technique was examined as a method for recovering Pd, Rh and Ru from fission products. The mixture of fission product oxides is combined with glass-forming chemicals, a metal oxide such as PbO (scavenging agent), and a reducing agent such as charcoal. When this mixture is melted, a metal button is formed which extracts the noble metals. The remainder cools to form a glass for nuclear waste storage. Recovery depended only on reduction of the scavenger oxide to metal. When such reduction was achieved, no difference in noble metal recovery efficiency was found among the scavengers studied (PbO, SnO, CuO, Bi 2 O 3 , Sb 2 O 3 ). Not all reducing agents studied, however, were able to reduce all scavenger oxides to metal. Only graphite would reduce SnO and CuO and allow noble metal recovery. The scavenger oxides Sb 2 O 3 , Bi 2 O 3 , and PbO, however, were reduced by all of the reducing agents tested. Similar noble metal recovery was found with each. Lead oxide was found to be the most promising of the potential scavengers. It was reduced by all of the reducing agents tested, and its higher density may facilitate the separation. Use of lead oxide also appeared to have no deterimental effect on the glass quality. Charcoal was identified as the preferred reducing agent. As long as a separable metal phase was formed in the melt, noble metal recovery was not dependent on the amount of reducing agent and scavenger oxide. High glass viscosities inhibited separation of the molten scavenger, while low viscosities allowed volatile loss of RuO 4 . A viscosity of approx. 20 poise at the processing temperature offered a good compromise between scavenger separation and Ru recovery. Glasses in which PbO was used as the scavenging agent were homogeneous in appearance. Resistance to leaching was close to that of certain waste glasses reported in the literature. 12 figures. 7 tables

The unbalanced signal measuring of automotive brake drum

Science.gov (United States)

Wang, Xiao-Dong; Ye, Sheng-Hua; Zhang, Bang-Cheng

2005-04-01

For the purpose of the research and development of automatic balancing system by mass removing, the dissertation deals with the measuring method of the unbalance signal, the design the automatic balance equipment and the software. This paper emphases the testing system of the balancer of automotive brake drum. The paper designs the band-pass filter product with favorable automatic follow of electronic product, and with favorable automatic follow capability, filtration effect and stability. The system of automatic balancing system by mass removing based on virtual instrument is designed in this paper. A lab system has been constructed. The results of contrast experiments indicate the notable effect of 1-plane automatic balance and the high precision of dynamic balance, and demonstrate the application value of the system.

Noble metals in cretaceous/tertiary sediments from El Kef

International Nuclear Information System (INIS)

Kuslys, M.; Kraehenbuehl, U.

1983-01-01

Sediments from El Kef, Tunisia, were analysed by RNAA for Au, Ir and Os. All three elements show a 10-20 fold enrichment at the Cretaceous/Tertiary boundary. This enrichment must be the result of the addition of material with a high concentration of noble metals. It is plausible that this exotic material has an extra-terrestrial origin. (orig.)

Noble metals in Cretaceous/Tertiary sediments from El Kef

International Nuclear Information System (INIS)

Kuslys, M.; Kraehenbuehl, U.

1983-01-01

Sediments from El Kef, Tunisia, were analysed by RNAA for Au, Ir and Os. All three elements show a 10-20 fold enrichment at the Cretaceous/Tertiary boundary. This enrichment must be the result of the addition of material with a high concentration of noble metals. It is plausible that this exotic material has an extraterrestrial origin. (orig.)

Rational design of binder-free noble metal/metal oxide arrays with nanocauliflower structure for wide linear range nonenzymatic glucose detection

KAUST Repository

Li, Zhenzhen; Xin, Yanmei; Zhang, Zhonghai; Wu, Hongjun; Wang, Peng

2015-01-01

One-dimensional nanocomposites of metal-oxide and noble metal were expected to present superior performance for nonenzymatic glucose detection due to its good conductivity and high catalytic activity inherited from noble metal and metal oxide

Interaction between Nafion ionomer and noble metal catalyst for PEMFCs

DEFF Research Database (Denmark)

Andersen, Shuang Ma

The implement of polymer impregnation in electrode structure (catalyst layer) decreasing the noble metal catalyst loading by a factor of ten , , is one of the essential mile stones in the evolution of Proton Exchange Membrane Fuel Cells’ development among the application of catalyst support and e...

Not so Noble-Radon in the Environment and Associated Health ...

Indian Academy of Sciences (India)

Home; Journals; Resonance – Journal of Science Education; Volume 5; Issue 7. Radon: Not so Noble-Radon in the Environment and Associated Health Problems. Deepanjan Majumdar. General Article Volume 5 Issue 7 July 2000 pp 44-55. Fulltext. Click here to view fulltext PDF. Permanent link:

Mitochondrial cytochrome oxidase I gene analysis indicates a restricted genetic background in Finnish noble crayfish (Astacus astacus stocks

Directory of Open Access Journals (Sweden)

Makkonen J.

2015-01-01

Full Text Available The IUCN Red List indexes the noble crayfish (Astacus astacus as vulnerable, with a declining population trend. The main threats to the species are the crayfish plague caused by the oomycete Aphanomyces astaci and the introduced North American crayfish that act as the carriers of this disease. In Finland, the noble crayfish is considered as a native species, which original distribution area covers the southern part of the country, but the species distribution has been dispersed to cover almost the whole country. The aim of this study was to survey the genetic diversity among the Finnish noble crayfish populations. The mitochondrial cytochrome oxidase I (COI-gene was sequenced from 742 individuals representing 59 populations from Finland and Estonia. As a result, only a single haplotype was found. Based on these results, the genetic diversity of noble crayfish in its Northern distribution range is remarkably low. The observed lack of variation can result from several mechanisms including small size of the founder population and the intense spreading of the species by manmade stockings. The restricted diversity can also be caused by eradication of the original populations due to crayfish plague epidemics and spreading of the invasive crayfish species carrying the crayfish plague. It is also possible that all contemporary Finnish noble crayfish populations originate from stockings with no variation in respect to COI-gene.

Simulation Modeling of Non-Homogeneous Mixture in the Horizontal Drum Mixer

Directory of Open Access Journals (Sweden)

Andrey Vladimirovich Ostroukh

2015-05-01

Full Text Available The paper proposes a simulation model of the diffusion mixing of solids, based on the theory of probability and stochastic diffusion model of imperfect processes of solid particles. It is assumed that the particles have different sizes and density. Model of the program implemented in the AnyLogic SoftWare. Developed a simulation model to evaluate the differences between the intense mixing processes in time and assess their impact on the course of other processes in a horizontal drum mixer.

Head Trauma: First Aid

Science.gov (United States)

First aid Head trauma: First aid Head trauma: First aid By Mayo Clinic Staff Most head trauma involves injuries that are minor and don't require ... 21, 2015 Original article: http://www.mayoclinic.org/first-aid/first-aid-head-trauma/basics/ART-20056626 . Mayo ...

Prevalence of interpersonal trauma exposure and trauma-related disorders in severe mental illness

NARCIS (Netherlands)

Mauritz, M.W.; Goossens, P.J.J.; Draijer, N.; Achterberg, T. van

2013-01-01

BACKGROUND: Interpersonal trauma exposure and trauma-related disorders in people with severe mental illness (SMI) are often not recognized in clinical practice. OBJECTIVE: To substantiate the prevalence of interpersonal trauma exposure and trauma-related disorders in people with SMI. METHODS: We

Prevalence of interpersonal trauma exposure and trauma-related disorders in severe mental illness

NARCIS (Netherlands)

Mauritz, M.W.; Goossens, P.J.J.; Draijer, N.; van Achterberg, T.

2013-01-01

Background: Interpersonal trauma exposure and trauma-related disorders in people with severe mental illness (SMI) are often not recognized in clinical practice. Objective: To substantiate the prevalence of interpersonal trauma exposure and trauma-related disorders in people with SMI. Methods: We

Steam drying compared to drum drying markedly increases early phase rumen fermentability of sugar beet pulp

DEFF Research Database (Denmark)

Nielsen, Mette Olaf; Larsen, Kasper; Jensen, Arne Sloth

2017-01-01

Freshly pressed and dried sugar beet pulp was sampled from 2 different factories located within a distance of 30 km and on 4 different dates. One factory was equipped with a steam dryer and the other with a drum dryer. A recognized in vitro technique was used to establish, how the drying process...... affected rumen fermentability of the pulp, since fibrous feeds (such as sugar beet pulp) rely on microbial fermentation in the rumen to be digestible to the cow. Steam dried pulp had a remarkable >60% higher fermentability compared to drum dried pulp during the first 12(-15) hours of fermentation...... (such as pectin) and small particles as low as 6.7-13.3 hours. Future feeding trials are needed to establish exactly how much the feeding value is increased in steam dried sugar beet pulp....

The Underwater Recovery of Monumental Marble Column Drums from an Ancient Shipwreck at Kızılburun, Turkey

Science.gov (United States)

Carlson, Deborah N.

2016-08-01

In the first century B.C., a stone carrier sank off the Aegean coast of Turkey at Kızılburun transporting all the elements of a monumental marble column, including a single Doric capital and eight drums. The 60-tonne cargo lay at a depth of 45-48 m and was excavated in its entirety by the Institute of Nautical Archaeology at Texas A&M University between 2005 and 2011. Ongoing research has shown that the Doric column pieces in the Kızılburun cargo originated in the marble quarries on Proconnesus Island in the Sea of Marmara and were very likely heading for the Temple of Apollo at Claros when the ship sank just 50 km short of its destination. The complete recovery of the ship's cargo posed a unique set of methodological challenges involving lifting the multi-tonne marble drums without disturbing the delicate waterlogged wooden hull remains preserved beneath. This report summarizes the solutions developed over five seasons in order to rig, hoist, move, and ultimately raise to the surface eight large ancient marble column drums (as well as all the other marble artifacts in the cargo) from a depth of almost 50 m under water.

Investigation and analytical results of bituminized products in drums at filing room