Cycle analysis of MCFC/gas turbine system

Science.gov (United States)

Musa, Abdullatif; Alaktiwi, Abdulsalam; Talbi, Mosbah

2017-11-01

High temperature fuel cells such as the solid oxide fuel cell (SOFC) and the molten carbonate fuel cell (MCFC) are considered extremely suitable for electrical power plant application. The molten carbonate fuel cell (MCFC) performances is evaluated using validated model for the internally reformed (IR) fuel cell. This model is integrated in Aspen Plus™. Therefore, several MCFC/Gas Turbine systems are introduced and investigated. One of this a new cycle is called a heat recovery (HR) cycle. In the HR cycle, a regenerator is used to preheat water by outlet air compressor. So the waste heat of the outlet air compressor and the exhaust gases of turbine are recovered and used to produce steam. This steam is injected in the gas turbine, resulting in a high specific power and a high thermal efficiency. The cycles are simulated in order to evaluate and compare their performances. Moreover, the effects of an important parameters such as the ambient air temperature on the cycle performance are evaluated. The simulation results show that the HR cycle has high efficiency.

Status of MCFC stack technology at IHI

Energy Technology Data Exchange (ETDEWEB)

Hosaka, M.; Morita, T.; Matsuyama, T.; Otsubo, M. [Ishikawajima-Harima Heavy Industries Co., Ltd., Tokyo (Japan)

1996-12-31

The molten carbonate fuel cell (MCFC) is a promising option for highly efficient power generation possible to enlarge. IHI has been studying parallel flow MCFC stacks with internal manifolds that have a large electrode area of 1m{sup 2}. IHI will make two 250 kW stacks for MW plant, and has begun to make cell components for the plant. To improve the stability of stack, soft corrugated plate used in the separator has been developed, and a way of gathering current from stacks has been studied. The DC output potential of the plant being very high, the design of electric insulation will be very important. A 20 kW short stack test was conducted in 1995 FY to certificate some of the improvements and components of the MW plant. These activities are presented below.

Transport phenomena in the cathode of a molten carbonate fuel cell

International Nuclear Information System (INIS)

Berg, P.; Findlay, J.

2009-01-01

'Full text': A Molten Carbonate Fuel Cell (MCFC) is an electro-chemical energy conversion technology that runs on natural gas and employs a molten salt electrolyte. In order to keep the electrolyte in this state, the cell must be kept at a temperature above 500 C, eliminating the need for noble catalysts. There has been only a limited amount of research on modelling the transport processes inside this device, mainly due to its limited ability for mobile applications. A model for the reaction-diffusion processes within the cathode of a MCFC is developed using Fick's Law for diffusion and incorporating Darcy's Law for convection. A model for Binary Diffusion is also discussed and compared to those for Fickian diffusion. It can be shown that there exists a limiting case for diffusion across the cathode that depends on the conductivity for the liquid potential, for which there exists an analytical solution. Results are also discussed for varying diffusivities and permeabilities. Ultimately, this research focuses on the optimization of the electrode porosity to increase the power output of the fuel cell. The porosity is considered as a function of position, and is optimized using the software package MATLAB. (author)

Performance Analysis of a MCFC/MGT Hybrid Power System Bi-Fueled by City Gas and Biogas

Directory of Open Access Journals (Sweden)

Hongyu Huang

2015-06-01

Full Text Available This study evaluates the performance of a molten carbonate fuel cell and micro gas turbine (MCFC/MGT hybrid power system bi-fueled by city gas and biogas. The performance of the MCFC/MGT hybrid power system and MFCF/MGT hybrid power system response have been investigated experimentally and numerically. Results show that the MCFC, steam reformer, and catalytic combustor models are in agreement with the experimental results of the system fueled by city gas only and the system bi-fueled by city gas and biogas. The MFCF/MGT hybrid power system can have manifest operation with the addition of biogas at a flow rate of up to 150.0 Nm3·h−1, which is about 50% of the overall input heat value. In addition, the MCFC and MGT outputs decrease with the increase in the flow rate of added biogas, with an overall power generation efficiency ranging from 39.0% to 42.0%. Furthermore, the MCFC/MGT hybrid power system can be operated stably both at low amplitude with slow current change and large amplitude with rapid power conditions. Finally, the MCFC/MGT hybrid system bi-fueled by city gas and biogas may be applicable to the energy supply of the micro–grid network.

Bismuth-doped La1.75Sr0.25NiO4+: δ as a novel cathode material for solid oxide fuel cells

NARCIS (Netherlands)

Zhu, Zhesheng; Li, Mei; Xia, Changrong; Bouwmeester, Henny J.M.

2017-01-01

Bismuth has been doped into mixed ionic-electronic conducting La1.75Sr0.25NiO4+δ (LSN) with the 2D K2NiF4-type structure to evaluate its influence on various properties of the host material, which include its potential use as a SOFC cathode. X-ray powder diffraction indicates that LSN retains its

The effects of system configuration and operating condition on the MCFC system efficiency

Energy Technology Data Exchange (ETDEWEB)

Kang, B.S. [Korea Electric Power Research Institute, Taejeon (Korea)

2001-07-01

The process simulation model of an externally reformed molten carbonate fuel cell (MCFC) system is used to analyze quantitatively the parametric effect on the system efficiency. In order to verify the MCFC process simulation model, the 25-kW system was analyzed on the basis of the experimental data and its calculated efficiency showed reasonable. The overall system efficiency of high-temperature fuel cell system, especially MCFC, can not be increased without the proper thermal integration between heat recovery units and additional power generation from auxiliary power generating units such as turbines. The simulation results show that the configuration of unit operators in a given system has great effect on the system efficiency while the system size and operating condition have slightly lower effect on it. Based on the system configuration, optimal operating condition including fuel, oxidant utilization, and recycle ratio can be specified to maximize the system efficiency. (author). 12 refs., 10 figs., 2 tabs.

Development of MCFC and PEFC technologies; Jisedai nenryo denchi no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Hori, M; Ozu, H; Sonai, A [Toshiba Corp. Tokyo (Japan)

1996-06-01

Next-generation fuel cells under development by Toshiba Corporation are outlined. The molten carbonate fuel cell (MCFC) has become stable in performance, which results from the conversion of the matrix group from the {gamma}-type to {alpha}-type LiAlO2. The cathode material is expected to withstand the elution of electrolyte for 20000 hours. The soft structure separator developed for stack constitution is expected to improve electrical contact and reduce the cost of stack. An appliance has been completed to tentatively produce every element concerned. During an actual operation, the structural soundness of the 2-cell stack was confirmed by thermal load tests. As for the polymer electrolyte fuel cell (PEFC), an interior humidification method has been developed using a porous material for supplying water to the polymer film. The amount of moisture can be controlled, which will enable a larger-area cell. A 1kW-class stack with a world-record-level 1200cm{sup 2} electrode area has been developed, which stack has shown that the target output has been attained. Furthermore, the power generation efficiency of the system including fuel treatment has been examined. 10 figs.

Simulated coal gas MCFC power plant system verification. Final report

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-07-30

The objective of the main project is to identify the current developmental status of MCFC systems and address those technical issues that need to be resolved to move the technology from its current status to the demonstration stage in the shortest possible time. The specific objectives are separated into five major tasks as follows: Stack research; Power plant development; Test facilities development; Manufacturing facilities development; and Commercialization. This Final Report discusses the M-C power Corporation effort which is part of a general program for the development of commercial MCFC systems. This final report covers the entire subject of the Unocal 250-cell stack. Certain project activities have been funded by organizations other than DOE and are included in this report to provide a comprehensive overview of the work accomplished.

Design, Construction and Operation of a Molten Carbonate Fuel Cell (MCFC) in the 100-kW-Class

International Nuclear Information System (INIS)

Heiming, Andreas; Huppmann, Gerhard; Aasberg-Petersen, Kim

1999-01-01

In fuel cells, the electrochemical energy of the fuel is converted directly into electricity and heat. The electrochemical conversion is inherently related to high electrical efficiencies and very low pollutant emissions. Fuel cells with sufficiently high operating temperatures such as (1) the phosphoric acid fuel cell (PAFC), operating temperature: 200 o C, (2) the molten carbonate fuel cell (MCFC), operating temperature: 650 o C and (3) the solid oxide fuel cell (SOFC), operating temperature: around 900 o C are best suited for decentralised combined heat and power (CHP) applications. This is due to the fact, that the heat of the exothermic reaction taking place in the fuel cell can be used in the domestic, commercial and industrial sector for heating and hot water or steam production. At the present time, gas-engines or gas-turbines are the preferred CHP-technologies for these applications. Nowadays, the PAFC is commercially available. More than 160 plants, each with a power of 200 kW, have been installed world-wide. Ruhrgas has investigated the behaviour of a 200 kW PAFC at its research centre in Dorsten, Germany, and at the site of a local utility. High temperature fuel cells such as MCFC or SOFC promise electrical efficiencies above 50 % in simple cycle mode. Up to now, MCFC-test plants have been built and operated in the 100 kW to 1 MW power range. The largest MCFC ever operated consisted of 16 identical stacks of 125 kW each, resulting in a plant power of 2 MW. The initial experience with SOFC in this power-range is currently gained from the operation of a 100 kW plant. In this paper, the result of the construction and operation of a highly innovatively designed 280 kW MCFC will be presented. This plant has been designed, built and operated by a European consortium for the development and market introduction of the MCFC. Members of the consortium are MTU-Friedrichshafen GmbH, Haldor Topsoee NS, Elkraft A.m.b.H., RWE Energie AG and Ruhrgas AG. (author)

Relative abundance estimations of Chengal trees in a tropical rainforest by using modified canopy fractional cover (mCFC)

International Nuclear Information System (INIS)

Hassan, N

2014-01-01

Tree species composition estimations are important to sustain forest management. This study estimates relative abundance of useful timber tree species (chengal) using Hyperion EO-1 satellite data. For the estimation, modified Canopy Fractional Cover (mCFC) was developed using Canopy Fractional Cover (CFC). mCFC was more sensitive to estimate relative abundance of chengal trees rather than Mixture Tuned Matched Filtering (MTMF). Meanwhile, MTMF was more sensitive to estimate the relative abundance of undisturbed forest. Accuracy suggests that the mCFC model is better to explain relative abundance of chengal trees than MTMF. Therefore, it can be concluded that relative abundance of tree species extracted from Hyperion EO-1 satellite data using modified Canopy Fractional Cover is an obtrusive approach used for identifying tree species composition

Relative abundance estimations of chengal tree in a tropical rainforest by using modified Canopy Fractional Cover (mCFC)

International Nuclear Information System (INIS)

Hassan, N

2014-01-01

Tree species composition estimations are important to sustain forest management. This study challenged estimates of relative abundance of useful timber tree species (chengal) using Hyperion EO-1 satellite data. For the estimation, modified Canopy Fractional Cover (mCFC) was developed using Canopy Fractional Cover (CFC). mCFC was more sensitive to estimate relative abundance of chengal trees rather than Mixture Tuned Matched Filtering (MTMF). Meanwhile, MTMF was more sensitive to estimate the relative abundance of undisturbed forest. Accuracy suggests that the mCFC model is better to explain relative abundance of chengal trees than MTMF. Therefore, it can be concluded that relative abundance of trees species extracted from Hyperion EO-1 satellite data using modified Canopy Fractional Cover is an obtrusive approach used for identifying trees species composition

Demonstration of direct internal reforming for MCFC power plants

Energy Technology Data Exchange (ETDEWEB)

Aasberg-Petersen, K.; Christensen, P.S.; Winther, S.K. [HALDOR TOPSOE A/S, Lynby (Denmark)] [and others

1996-12-31

The conversion of methane into hydrogen for an MCFC by steam reforming is accomplished either externally or internally in the stack. In the case of external reforming the plant electrical efficiency is 5% abs. lower mainly because more parasitic power is required for air compression for stack cooling. Furthermore, heat produced in the stack must be transferred to the external reformer to drive the endothermic steam reforming reaction giving a more complex plant lay-out. A more suitable and cost effective approach is to use internal steam reforming of methane. Internal reforming may be accomplished either by Indirect Internal Reforming (DIR) and Direct Internal Reforming (DIR) in series or by DIR-only as illustrated. To avoid carbon formation in the anode compartment higher hydrocarbons in the feedstock are converted into hydrogen, methane and carbon oxides by reaction with steam in ail adiabatic prereformer upstream the fuel cell stack. This paper discusses key elements of the desire of both types of internal reforming and presents data from pilot plants with a combined total of more than 10,000 operating hours. The project is being carried out as part of the activities of the European MCFC Consortium ARGE.

Physical properties of molten carbonate electrolyte

Energy Technology Data Exchange (ETDEWEB)

Kojima, T.; Yanagida, M.; Tanimoto, K. [Osaka National Research Institute (Japan)] [and others

1996-12-31

Recently many kinds of compositions of molten carbonate electrolyte have been applied to molten carbonate fuel cell in order to avoid the several problems such as corrosion of separator plate and NiO cathode dissolution. Many researchers recognize that the addition of alkaline earth (Ca, Sr, and Ba) carbonate to Li{sub 2}CO{sub 3}-Na{sub 2}CO{sub 3} and Li{sub 2}CO{sub 3}-K{sub 2}CO{sub 3} eutectic electrolytes is effective to avoid these problems. On the other hand, one of the corrosion products, CrO{sub 4}{sup 2-} ion is found to dissolve into electrolyte and accumulated during the long-term MCFC operations. This would affect the performance of MCFC. There, however, are little known data of physical properties of molten carbonate containing alkaline earth carbonates and CrO{sub 4}{sup 2-}. We report the measured and accumulated data for these molten carbonate of electrical conductivity and surface tension to select favorable composition of molten carbonate electrolytes.

Experimental comparison of MCFC performance using three different biogas types and methane

Science.gov (United States)

Bove, Roberto; Lunghi, Piero

Biogas recovery is an environmentally friendly and cost-effective practice that is getting consensus in both the scientific and industrial community, as the growing number of projects demonstrate. The use of fuel cells as energy conversion systems increases the conversion efficiency, as well as the environmental benefits. Molten carbonate fuel cells (MCFC) operate at a temperature of about 650 °C, thus presenting a high fuel flexibility, compared to low temperature fuel cells. Aim of the present study is to compare the performance of an MCFC single cell, fuelled with different biogas types as well as methane. The biogases considered are derived from the following processes: (1) steam gasification in an entrained flow gasifier; (2) steam gasification in a duel interconnect fluidized bed gasifier; (3) biogas from an anaerobic digestion process. The performances are evaluated for different fuel utilization and current densities. The results are an essential starting point for a complete system design and demonstration.

Operation characteristics of a multiple type MCFC

Energy Technology Data Exchange (ETDEWEB)

Kuroe, S.; Kamo, T. [Hitachi Research Lab., Hitachi, Ltd., Ibaraki-ken (Japan); Fujimura, H.; Kahara, T. [Hitachi, Ltd., Ibaraki-ken (Japan)

1996-12-31

Multiple type structure of MCFC of which the separator of the cell is divided by four element cells has been studied. For the stable operation of this type cell, the effect of gas flow rate and temperature distribution on the cell voltage should be clear. In order to clarify these characteristics, a small sized mimic model has been made and tested. The flow rate distribution for the four element cells were varied and cell voltage and temperature distribution were measured for each cell. The decrease in cell voltage and the increase in maximum temperature became remarkable when the apparent utilization factor for one element cell became over 100%. The calculated results agreed fairly good with test results.

Development of 1000kW-class MCFC pilot plant

Energy Technology Data Exchange (ETDEWEB)

Ooue, M.; Yasue, H. [MCFC Research Association, Mie (Japan); Takasu, K.; Tsuchitori, T.

1996-12-31

This pilot plant is a part of the New Sunshine Program which has proceeded by the Agency of Industrial Science and Technology of the Ministry of International Trade and Industry. MCFC Research Association is entrusted with the development of the pilot plant, and constructing it at Kawagoe site. Following items will be verified by this pilot plant operation. (a) Development of 250kW class stack and confirmation of stack performance and decay rate. (b) System verification such as basic process, control system and operation characteristics, toward commercialization. (c) To get design data for demonstration plant.

MCFC power plant with CO{sub 2} separation

Energy Technology Data Exchange (ETDEWEB)

Kinoshita, Noboru [Ishikawajima-Harima Heavy Industries Co., Ltd., Tokyo (Japan)

1996-12-31

Fuel cell power plant has been developed for many years with expectation of high system efficiency. In the meantime the gas turbine combined cycle has shown its considerable progress in improving system efficiency. Fuel cell power plant will no longer be attractive unless it exceeds the gas turbine combined cycle at least in the system efficiency. It is said CO{sub 2} separation could improve the efficiency of fuel cell power plant. IHI has developed the CO{sub 2} separator for fuel cell power plant. This study describes that the CO{sub 2} separator can increase the efficiency of the molten carbonate fuel cell (MCFC) power plant by 5% and the expected efficiency reaches 63 % in HHV basis.

MOLCARE development towards MCFC commercial power plants based on 500 kW standard modules

Energy Technology Data Exchange (ETDEWEB)

Torazza, A; Dufour, A; Perfumo, A; Ricerche, A; Gegundez, J; Sanson, F; Moreno, A

1998-07-01

Fuel cells technologies for stationary applications are expected to play a remarkable role in the field of next decade energy production systems ranging from some hundreds kW to some MW. The interest in using fuel cells to produce electric energy comes from the advantages that fuel cells offer in terms of high efficiency, good behavior at base and partial load, very low emissions, modularity (easy adjustment of plant capacity to power-demand increase), and reduced time to be spent for plant erection. At least four types of fuel cells can be considered suitable for stationary applications. With reference to their electrolyte they can be classified as: Polymeric Electrolyte Membrane Fuel Cells (PEMFC), Phosphoric Acid Fuel Cells (PAFC), Molten Carbonate Fuel Cells (MCFC) and Solid Oxide Fuel Cells (SOFC). Each of them works at a temperature level that is depending on the type of electrolyte. From a general point of view all the fuel cell technologies present, at various extents, the above listed advantages. Nevertheless specific features of each fuel cell type suggest to identify a specific field of application for each type of solution, in order to stress the potential advantages of any technology and minimize its possible drawbacks. Anyway the different level of maturity for the various fuel cell technologies does not allow an homogeneous comparison of technical and economical key parameters. PAFCs, due to their present commercial availability and operation experience, are well outlined in terms of performance and costs; on the contrary with regard to the other technologies--PEMFC, MCFC and SOFC--which are still under development, their commercialization is expected within a period of 7 to 13 years according to single technology maturity level (MCFC level seems to be more ready), kind of application, competitors, environmental constraints, etc.

Operation test for 200-kW class internally improved MCFC stacks having achieved 5000 hours; 200kW kyu naibu kaishitsu gata MCFC sutakku unten shiken 5,000 jikan tassei

Energy Technology Data Exchange (ETDEWEB)

Hashino, K. [Kansai Electric Power Co. Inc., Osaka (Japan)

2000-03-10

The operation test for 200-kW class internally improved MCFC stacks being performed at the Amagasaki fuel cell power generation testing plant of Kansai Electric Power Co., Inc. has achieved on January 22, 2000 five thousand hours, the original test time target. Temperature raising has begun on June 18 last year, and the first power generation was carried out on June 30. Since then the operation has continued smoothly at near rated output, and the test was completed nearly as planned without experiencing any trouble caused by Y2K problem. This research is being carried out as the research work shared by the Molten Carbonate Fuel Cell Power Generation System Technology Research Association (MCFC Research Association) based on the research commissioning from NEDO as part of the New Sunshine Project. After the confirmation of the initial performance, verification of the carbon dioxide self-sustaining operation, and the property evaluation test of every 500 hours are going smoothly. The intention hereafter is to achieve 5,000 hours as the power generation time, with the schedule to reduce the stack temperature in the middle of February, and cease the operation. As of January 25, the amount of power generated reached 1,089 MWh. (NEDO)

Microstructure optimization for high-performance PrBa0.5Sr0.5Co1.5Fe0.5O5+δ-La2NiO4+δ core-shell cathode of solid oxide fuel cells

Science.gov (United States)

Li, Jin; Qiu, Peng; Xia, Meng; Jia, Lichao; Chi, Bo; Pu, Jian; Li, Jian

2018-03-01

Four PrBa0.5Sr0.5Co1.5Fe0.5O5+δ (PBSCF)-La2NiO4+δ (LN) core-shell cathodes, designated as PL-0, PL-1, PL-3 and PL-5, are prepared by infiltrating LN solution into PBSCF scaffold, and they are investigated in terms of the effect of LN thickness on their electrochemical performance. PL-3 with a continuous LN coating of a moderate average thickness (∼9 nm) demonstrates the lowest initial polarization resistance (0.51 Ω cm2) and highest power density (0.71 W cm-2) among all the cathodes. Polarized at 400 mA cm-2 and 700 °C for up to 40 h, the polarization resistance of all the prepared cathodes increases to approach a stable level after early stage decrease due to current activation, and PL-3 exhibits a slower average rate of performance degradation (25%). The electrochemical performance improvement is mainly attributed to that LN has a relatively high oxygen surface exchange coefficient and continuous LN coating depresses Sr segregation at PBSCF/LN interface.

Japan-EU joint research project on petroleum substituting energy; Nichi EU sekiyu daitai energy kanren kyodo kenkyu jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Four EU research workers were invited from Portugal, Italy and France for promoting R & D of petroleum substituting energies in Japan. The joint research on the wide area energy use network system (advanced district cooling and heating) includes the experimental technology for measuring heat transfer acceleration and drag reduction, evaluation of rheological characteristics of fluid, and development and selection of an adequate composition equation of fluid. The joint research on MCFC includes the test method and procedure of components and cells in relation to corrosion by molten carbonate, elution of NiO cathodes, electrode modeling and alternative materials for cathodes. The joint research on geothermal gases includes the research method of fumarolic gases such as volcanic gas and geothermal gas, applications in Italian geothermal fields and the relation of geothermal gases with the origin of fluid, deep conditions and volcanic activity. In addition, the joint research on light energy conversion (energy transfer system between binuclear metal complexes) and the performance and use of metal complexes as catalyst for polymer electrolyte fuel cells was also performed. 52 refs., 20 figs., 3 tabs.

Nickel oxide and carbon nanotube composite (NiO/CNT) as a novel cathode non-precious metal catalyst in microbial fuel cells.

Science.gov (United States)

Huang, Jianjian; Zhu, Nengwu; Yang, Tingting; Zhang, Taiping; Wu, Pingxiao; Dang, Zhi

2015-10-15

Comparing with the precious metal catalysts, non-precious metal catalysts were preferred to use in microbial fuel cells (MFCs) due to the low cost and high oxygen reduction reaction (ORR) efficiency. In this study, the transmission electron microscope and X-ray diffraction as well as Raman investigation revealed that the prepared nanoscale NiO was attached on the surface of CNT. Cyclic voltammogram and rotating ring-disk electrode tests showed that the NiO/CNT composite catalyst had an apparent oxygen reduction peak and 3.5 electron transfer pathway was acquired under oxygen atmosphere. The catalyst performance was highly dependent on the percentage of NiO in the CNT nanocomposites. When 77% NiO/CNT nano-sized composite was applied as cathode catalyst in membrane free single-chamber air cathode MFC, a maximum power density of 670 mW/m(2) and 0.772 V of OCV was obtained. Moreover, the MFC with pure NiO (control) could not achieve more than 0.1 V. All findings suggested that NiO/CNT could be a potential cathode catalyst for ORR in MFCs. Copyright © 2015 Elsevier B.V. All rights reserved.

A preliminary design and BOP cost analysis of M-C Power`s MCFC commerical unit

Energy Technology Data Exchange (ETDEWEB)

Chen, T.P. [Bechtel Corp, San Francisco, CA (United States)

1996-12-31

M-C Power Corporation plans to introduce its molten carbonate fuel cell (MCFC) market entry unit in the year 2000 for distributed and on-site power generation. Extensive efforts have been made to analyze the cell stack manufacturing costs. The major objective of this study is to conduct a detailed analysis of BOP costs based on an initial design of the market entry unit.

Improvement of biogas as a fuel in molten carbonate fuel cells (MCFC); Aprovechamiento del biogas como combustible en pilas de combustible de carbonatos fundidos (MCFC)

Energy Technology Data Exchange (ETDEWEB)

Gil Diez, J.

2002-07-01

Molten carbonate fuel cells (MCFC) have a high efficiency of approx 50% when using biogas as a fuel and are among all types of FC the best suited for biogas. A precondition for use biogas in fuel cells is the reduction of accompanying traces of detrimental gases, therefore the RTD-work is two fold: A Preprocessing unit must be developed and the expected endurance must be confirmed. As a lesson learned in prior projects major reasons why renewable energy projects fail is the one-sided focus on technical aspects, that is why non-technical barriers shall be taken into account and realistic recommendations have to be established to overcome possible economic, logistic, legal and social problems. (Author)

Carbon nanowalls in field emission cathodes

Directory of Open Access Journals (Sweden)

Belyanin A. F.

2017-12-01

Full Text Available The carbon nanowall (CNW layers were grown from a gas mixture of hydrogen and methane, activated by a DC glow discharge, on Si substrates (Si/CNW layered structure. The second layer of CNW was grown either on the first layer (Si/CNW/CNW structure or on Ni or NiO films deposited on the first CNW layer (Si/CNW/Ni/CNW and Si/CNW/NiO/CNW structures. The composition and structure of the resulting layered structures were studied using scanning electron microscopy, Raman spectroscopy, and X-ray diffractometry. It was found that annealing of Si/CNW structure in vacuum, growing of the second CNW layer on Si/CNW, as well as deposition of Ni or NiO films prior to the growing of the second CNW layer improve functional properties of field emission cathodes based on the electron-emitting CNW layers.

Structure, stability, and thermomechanical properties of Ca-substituted Pr2NiO4 + δ

Science.gov (United States)

Pikalova, E. Yu.; Medvedev, D. A.; Khasanov, A. F.

2017-04-01

Ca-substituted layered nickelates with a general Pr2- x Ca x NiO4 + δ composition ( x = 0-0.7, Δ x = 0.1) were prepared in the present work and their structural and physic-chemical properties were investigated in order to select the most optimal materials, which can be used as cathodes for solid oxide fuel cells. With an increase in Ca content in Pr2- x Ca x NiO4 + δ the following tendencies were observed: (i) a decrease in the concentration of nonstoichiometric oxygen (δ), (ii) a decrease in the unit cell parameters and volume, (iii) stabilization of the tetragonal structure, (iv) a decrease of the thermal expansion coefficients, and (v) enchancement of thermodynamic stability and compatibility with selected oxygen- and proton-conducting electrolytes. The Pr1.9Ca0.1NiO4 + δ material, having highest δ value, departs from the general "properties-composition" dependences ascertained. This indicates that oxygen non-stoichiometry has determining influence on the functional properties of layered nickelates.

Cobalt, titanium or cerium oxide protective coatings for the nickel cathode of the molten carbonate fuel cells; Revetements protecteurs a base d'oxyde de cobalt, de titane ou de cerium pour la cathode de nickel des piles a combustible a carbonates fondus

Energy Technology Data Exchange (ETDEWEB)

Mendoza Blanco, L.

2003-10-15

The aim of this work is to combine the MCFC cathode Li{sub x}Ni{sub 1-x}O properties to those of the protective coatings of LiCoO{sub 2}, Li{sub 2}TiO{sub 3} or of CeO{sub 2}, less soluble in the molten carbonates. In the cases of LiCoO{sub 2}, have been carried out by controlled potential coulometry in aqueous solution, a deposition of Co{sub 3}O{sub 4} on dense Ni. The cobalt oxide reacts rapidly in the Li{sub 2}CO{sub 3}-Na{sub 2}CO{sub 3} medium at 650 C to give LiCoO{sub 2}, a spinel cubic phase revealed by Raman spectroscopy. (O.M.)

Synthesis of Octahedral-Shaped NiO and Approaches to an Anode Material of Manufactured Solid Oxide Fuel Cells Using the Decalcomania Method

Directory of Open Access Journals (Sweden)

Haeran Cho

2013-01-01

Full Text Available Micrometer-sized and octahedral-shaped NiO particles were synthesized by microwave thermal treatment at 300 watt power for 15 min in a microwave chamber to be used as an anode material in solid oxide fuel cells. SEM image and particle size distribution revealed near-perfect octahedral NiO microparticle with sizes ranging from 4.0~11.0 μm. The anode functional layer (AFL, 60 wt% NiO synthesized: commercial 40 wt% YSZ, electrolyte (commercial Yttria-stabilized zirconia, YSZ, and cathode (commercial La0.8Sr0.2MnO3, LSM layers were manufactured using the decalcomania method on a porous anode support, sequentially. The sintered electrolyte at 1450°C for 2 h using the decalcomania method was dense and had a thickness of about 10 μm. The cathode was sintered at 1250°C for 2 h, and it was porous. Using humidified hydrogen as a fuel, a coin cell with a 15 μm thick anode functional layer exhibited maximum power densities of 0.28, 0.38, and 0.65 W/cm2 at 700, 750, and 800°C, respectively. Otherwise, when a commercial YSZ anode functional layer was used, the maximum power density was 0.55 W/cm2 at 800°C.

An impressive approach to solving the ongoing stability problems of LiCoPO4 cathode: Nickel oxide surface modification with excellent core-shell principle

Science.gov (United States)

Örnek, Ahmet

2017-07-01

Nanoscale and NiO-coated LiCoPO4 cathode materials were prepared for the first time by a newly designed three-step synthesis route, which is a combined technique including advantages of the Stöber, hydrothermal and microwave synthesis methods. Using this extraordinary technique, LiCoPO4 particles are coated with a thin NiO layer with a perfect core-shell morphology and the technique's positive contribution to electrochemistry is elucidated in detail. The samples are interpreted using opto-analytical techniques and galvanostatic charge-discharge tests. The high-resolution transmission electron microscopy analysis proves that this well-elaborated technique makes it possible to achieve a continuous NiO surface coverage of 8-10 nm, a result that contributes towards solving the chronic electrochemical problems of 4.8 V cathode material. Our data reveal that NiO-coated LiCoPO4 cathode demonstrates superior cycle stability and specific capacity at relatively low rates. The 2.5% wt. NiO-coated cathode exhibits the best electrochemical property, which reaches a discharge capacity of 159 mAh g-1 at 0.l C current rate and shows almost 85% capacity retention after 80 charge-discharge cycles. It therefore achieves partial success in improving the electrochemical properties of the LiCoPO4 cathode material, which is especially crucial for energy storage to be applied in electric vehicles and plug-in hybrid electric applications.

Neurônios espelho

Directory of Open Access Journals (Sweden)

Allan Pablo Lameira

2006-01-01

Full Text Available Os neurônios espelho foram descritos inicialmente em macaco Rhesus. Estes neurônios disparavam quando o macaco realizava ações específicas (como pegar uvas passa ou quando ele observava a mesma ação realizada por outro macaco ou por um pesquisador. Assim, estes neurônios possibilitam a compreensão da ação e/ou da intenção de outro animal pela ativação subliminar desta ação nos circuitos fronto-parietais. Estes neurônios estariam envolvidos com a origem da linguagem humana e a sua disfunção poderia causar autismo. Nesta revisão, descrevemos, em humanos e em primatas não-humanos, as áreas corticais com atividade tipo “neurônio espelho” e as áreas envolvidas com o planejamento e a execução explícita e implícita de ações. Existe uma grande sobreposição entre estas áreas, bem como com as áreas envolvidas com o reconhecimento da lateralidade de partes do corpo. Sugerimos então que os neurônios espelho também podem estar envolvidos com o reconhecimento da lateralidade de partes do corpo.

Properties of Copper Doped Neodymium Nickelate Oxide as Cathode Material for Solid Oxide Fuel Cells

Directory of Open Access Journals (Sweden)

Lee Kyoung-Jin

2016-06-01

Full Text Available Mixed ionic and electronic conducting K2NiF4-type oxide, Nd2Ni1-xCuxO4+δ (x=0~1 powders were synthesized by solid state reaction technique and solid oxide fuel cells consisting of a Nd2Ni1-xCuxO4+δ cathode, a Ni-YSZ anode and ScSZ as an electrolyte were fabricated. The effect of copper substitution for nickel on the electrical and electrochemical properties was examined. Small amount of copper doping (x=0.2 resulted in the increased electrical conductivity and decreased polarization resistance. It appears that this phenomenon was associated with the high mean valence of nickel and copper and the resulting excess oxygen (δ. It was found that power densities of the cell with the Nd2Ni1-xCuxO4+δ (x=0.1 and 0.2 cathode were higher than that of the cell with the Nd2NiO4+δ cathode.

LaNi1-xCoxO3-δ (x=0.4 to 0.7) cathodes for solid oxide fuel cells by infiltration

Science.gov (United States)

Chrzan, Aleksander; Ovtar, Simona; Chen, Ming

2016-01-01

Performance of LaNi1-xCoxO3-δ (LNC) (x=0.4 to 0.7) as a cathode in solid oxide fuel cell (SOFC) is evaluated. Symmetrical cathode/electrolyte/cathode cells for electrochemical testing are prepared by infiltration of yttria stabilized zirconia (YSZ) backbone with LNC solutions. It is showed that the cathode infiltrated with LaNi0.5Co0.5O3-δ (LNC155) has the lowest polarization resistance and activation energy, 197 mΩ cm2 at 600 °C and 0.91 eV, respectively. Therefore it is the most promising material of the LNC group for electrochemical applications. X-ray diffraction analysis revealed that none of the materials is single-phased after heat treatment at 800 °C as they contain residues of La2O3 and La2NiO4-δ

Status of the M-C Power IMHEX{reg_sign} MCFC commercialization program

Energy Technology Data Exchange (ETDEWEB)

Laurens, R.M.; Scroppo, J.A.; Petri, R.J.; Benjamin, T.G. [M-C Power Corp., Burr Ridge, IL (United States)

1996-12-31

Six years ago, M-C Power (MCP) developed a comprehensive business plan to commercialize molten carbonate fuel cell (MCFC) power plants. On an annual basis the plan has been reviewed and modified to adapt to identified end user needs and technological advancements. As a result, product definition kept abreast with marketing requirements. Over the last five years, there was order and reason for subtle shifts in supply, demand, competition and pricing policies. Today, however, traditional market assessment assumptions must be challenged. There is a revolution taking place. The revolution can be summed up in one word ... deregulation. Deregulation of the airline industry led to consideration of the natural gas industry. Now that natural gas deregulation is behind us, it is electric power and telecommunications that are receiving attention. Increased emphasis is being placed on achieving market-priced power. The net result will be thinner margins for the seller and the end user. What does this mean for the commercialization of molten carbonate fuel cells?

Operating experience with a 250 kW el molten carbonate fuel cell (MCFC) power plant

Science.gov (United States)

Bischoff, Manfred; Huppmann, Gerhard

The MTU MCFC program is carried out by a European consortium comprising the German companies MTU Friedrichshafen GmbH, Ruhrgas AG and RWE Energie AG as well as the Danish company Energi E2 S/A. MTU acts as consortium leader. The company shares a license and technology exchange agreement with Fuel Cell Energy Inc., Danbury, CT, USA (formerly Energy Research Corp., ERC). The program was started in 1990 and covers a period of about 10 years. The highlights of this program to date are: Considerable improvements regarding component stability have been demonstrated on laboratory scale. Manufacturing technology has been developed to a point which enables the consortium to fabricate the porous components on a 250 cm 2 scale. Several large area stacks with 5000-7660 cm 2 cell area and a power range of 3-10 kW have been tested at the facilities in Munich (Germany) and Kyndby (Denmark). These stacks have been supplied by FCE. As far as the system design is concerned it was soon realized that conventional systems do not hold the promise for competitive power plants. A system analysis led to the conclusion that a new innovative design approach is required. As a result the "Hot Module" system was developed by the consortium. A Hot Module combines all the components of a MCFC system operating at the similar temperatures and pressures into a common thermally insulated vessel. In August 1997 the consortium started its first full size Hot Module MCFC test plant at the facilities of Ruhrgas AG in Dorsten, Germany. The stack was assembled in Munich using 292 cell packages purchased from FCE. The plant is based on the consortium's unique and proprietary "Hot Module" concept. It operates on pipeline natural gas and was grid connected on 16 August 1997. After a total of 1500 h of operation, the plant was intentionally shut down in a controlled manner in April 1998 for post-test analysis. The Hot Module system concept has demonstrated its functionality. The safety concept has been

Facile Synthesis of Hierarchical Mesoporous Honeycomb-like NiO for Aqueous Asymmetric Supercapacitors.

Science.gov (United States)

Ren, Xiaochuan; Guo, Chunli; Xu, Liqiang; Li, Taotao; Hou, Lifeng; Wei, Yinghui

2015-09-16

Three-dimensional (3D) hierarchical nanostructures have been demonstrated as one of the most ideal electrode materials in energy storage systems due to the synergistic combination of the advantages of both nanostructures and microstructures. In this study, the honeycomb-like mesoporous NiO microspheres as promising cathode materials for supercapacitors have been achieved using a hydrothermal reaction, followed by an annealing process. The electrochemical tests demonstrate the highest specific capacitance of 1250 F g(-1) at 1 A g(-1). Even at 5 A g(-1), a specific capacitance of 945 F g(-1) with 88.4% retention after 3500 cycles was obtained. In addition, the 3D porous graphene (reduced graphene oxide, rGO) has been prepared as an anode material for supercapacitors, which displays a good capacitance performance of 302 F g(-1) at 1 A g(-1). An asymmetric supercapacitor has been successfully fabricated based on the honeycomb-like NiO and rGO. The asymmetric supercapacitor achieves a remarkable performance with a specific capacitance of 74.4 F g(-1), an energy density of 23.25 Wh kg(-1), and a power density of 9.3 kW kg(-1), which is able to light up a light-emitting diode.

Ethanol Sensing Properties of Au-functionalized NiO Nanoparticles

International Nuclear Information System (INIS)

Park, Sunghoon; Kheel, Hyejoon; Sun, Gun-Joo; Hyun, Soong Keun; Park, Sang Eon; Lee, Chongmu

2016-01-01

Pristine and Au-functionalized nickel oxide (NiO) nanoparticles were synthesized via a simple solvo thermal route and the ethanol sensing properties of multiple-networked Au-doped and undoped NiO nanoparticle sensors were examined. The pristine and Au-functionalized NiO nanoparticle sensor showed responses of 442 and 273%, respectively, to 1000 ppm of ethanol at 325 .deg. C. The Au-functionalized NiO nanoparticle sensor showed faster response than the pristine NiO counterpart, whereas the recovery time of the former was similar to that of the latter. The optimal operating temperature of the pristine and Au-functionalized NiO nanoparticles was 325 and 350 .deg. C, respectively, by Au-doping. Both the pristine and Au-functionalized NiO nanoparticle sensors showed selectivity for ethanol gas over methanol, acetone, benzene, and toluene gases. The underlying mechanism of the enhanced sensing performance of the Au-functionalized NiO nanoparticles toward ethanol might be due to modulation of the depletion layer formed around Au particles and the Schottky barriers formed at the Au-NiO junction accompanying ethanol adsorption and desorption, the spill-over effect and high catalytic activity of Au nanoparticles and the smaller diameter of the particles in the Au-functionalized NiO sensor.

Ethanol Sensing Properties of Au-functionalized NiO Nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Park, Sunghoon; Kheel, Hyejoon; Sun, Gun-Joo; Hyun, Soong Keun; Park, Sang Eon; Lee, Chongmu [Inha University, Incheon (Korea, Republic of)

2016-05-15

Pristine and Au-functionalized nickel oxide (NiO) nanoparticles were synthesized via a simple solvo thermal route and the ethanol sensing properties of multiple-networked Au-doped and undoped NiO nanoparticle sensors were examined. The pristine and Au-functionalized NiO nanoparticle sensor showed responses of 442 and 273%, respectively, to 1000 ppm of ethanol at 325 .deg. C. The Au-functionalized NiO nanoparticle sensor showed faster response than the pristine NiO counterpart, whereas the recovery time of the former was similar to that of the latter. The optimal operating temperature of the pristine and Au-functionalized NiO nanoparticles was 325 and 350 .deg. C, respectively, by Au-doping. Both the pristine and Au-functionalized NiO nanoparticle sensors showed selectivity for ethanol gas over methanol, acetone, benzene, and toluene gases. The underlying mechanism of the enhanced sensing performance of the Au-functionalized NiO nanoparticles toward ethanol might be due to modulation of the depletion layer formed around Au particles and the Schottky barriers formed at the Au-NiO junction accompanying ethanol adsorption and desorption, the spill-over effect and high catalytic activity of Au nanoparticles and the smaller diameter of the particles in the Au-functionalized NiO sensor.

The effect of Fe2NiO4 and Fe4NiO4Zn magnetic nanoparticles on anaerobic digestion activity.

Science.gov (United States)

Chen, Jian Lin; Steele, Terry W J; Stuckey, David C

2018-06-11

Two types of magnetic nanoparticles (MNPs), i.e. Ni ferrite nanoparticles (Fe 2 NiO 4 ) and Ni Zn ferrite nanoparticles (Fe 4 NiO 4 Zn) containing the trace metals Ni and Fe, were added to the anaerobic digestion of synthetic municipal wastewater at concentrations between 1 and 100 mg Ni L -1 in order to compare their effects on biogas (methane) production and sludge activity. Using the production of methane over time as a measure, the assays revealed that anaerobic digestion was stimulated by the addition of 100 mg Ni L -1 in Fe 2 NiO 4 NPs, while it was inhibited by the addition of 1-100 mg Ni L -1 in Fe 4 NiO 4 Zn NPs. Especially at 100 mg Ni L -1 , Fe 4 NiO 4 Zn NPs resulted in a total inhibition of anaerobic digestion. The metabolic activity of the anaerobic sludge was tested using the resazurin reduction assay, and the assay clearly revealed the negative effect of Fe 4 NiO 4 Zn NPs and the positive effect of Fe 2 NiO 4 NPs. Re-feeding fresh synthetic medium reactivated the NPs added to the anaerobic sludge, except for the experiment with 100 mg Ni L -1 addition of Fe 4 NiO 4 Zn NPs. The findings in this present study indicate a possible new strategy for NPs design to enhance anaerobic digestion. Crown Copyright © 2018. Published by Elsevier B.V. All rights reserved.

Electrochemical reduction of NiO in a composite electrode

DEFF Research Database (Denmark)

Hu, Qiang; Jacobsen, Torben; Hansen, Karin Vels

2013-01-01

a lower overpotential. Microstructures of NiO with different reduction degrees are shown. Electrochemical impedance spectroscopy is carried out during the reduction process. Electrochemical reduction of NiO may need an induction period. When NiO is reduced at a constant voltage the current initially...

Microstructure and thermal conductivity of surfactant-free NiO nanostructures

Energy Technology Data Exchange (ETDEWEB)

Sahoo, Pranati [Laboratory for Emerging Energy and Electronic Materials, Materials Science and Engineering Department, University of Michigan, Ann Arbor, MI 48109 (United States); Department of Chemistry, University of New Orleans, New Orleans, LA 70148 (United States); Advanced Materials Research Institute, University of New Orleans, New Orleans, LA 70148 (United States); Misra, Dinesh K. [The Advanced Materials Research Institute, University of New Orleans, New Orleans, LA 70148 (United States); Salvador, Jim [Chemical Sciences and Materials Systems Laboratory, General Motors R and D Center, Warren, MI 48090 (United States); Makongo, Julien P.A. [Laboratory for Emerging Energy and Electronic Materials, Materials Science and Engineering Department, University of Michigan, Ann Arbor, MI 48109 (United States); Advanced Materials Research Institute, University of New Orleans, New Orleans, LA 70148 (United States); Chaubey, Girija S. [Advanced Materials Research Institute, University of New Orleans, New Orleans, LA 70148 (United States); Takas, Nathan J. [Laboratory for Emerging Energy and Electronic Materials, Materials Science and Engineering Department, University of Michigan, Ann Arbor, MI 48109 (United States); Advanced Materials Research Institute, University of New Orleans, New Orleans, LA 70148 (United States); Wiley, John B. [Department of Chemistry, University of New Orleans, New Orleans, LA 70148 (United States); Advanced Materials Research Institute, University of New Orleans, New Orleans, LA 70148 (United States); Poudeu, Pierre F.P., E-mail: ppoudeup@umich.edu [Laboratory for Emerging Energy and Electronic Materials, Materials Science and Engineering Department, University of Michigan, Ann Arbor, MI 48109 (United States); Department of Chemistry, University of New Orleans, New Orleans, LA 70148 (United States); Advanced Materials Research Institute, University of New Orleans, New Orleans, LA 70148 (United States)

2012-06-15

High purity, nanometer sized surfactant-free nickel oxide (NiO) particles were produced in gram scale using a solution combustion method and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), gas pycnometry and gas adsorption analysis (BET). The average particle size of the as-synthesized NiO increases significantly with the preheating temperature of the furnace, while the specific surface area decreases. A BET specific surface area of {approx}100 m{sup 2}/g was obtained for NiO nanoparticles with size as small as 3 nm synthesized at 300 Degree-Sign C. The thermal conductivity ({kappa}) of pressed pellets of the synthesized NiO nanoparticles obtained using spark plasma sintering (SPS) and uniaxial hot pressing is drastically decreased ({approx}60%) compared to that of NiO single crystal. This strong reduction in {kappa} with particle size suggests the suitability of the synthesized surfactant-free NiO nanoparticles for use as nanoinclusions when designing high performance materials for waste heat recovery. - Graphical abstract: Highly efficient phonon scattering by surfactant-free NiO nanostructures obtained by solution combustion of a mixture of nickel (II) nitrate hexahydrate (oxidizer) and urea (fuel) at various temperatures. Highlights: Black-Right-Pointing-Pointer Fast synthesis of surfactant-free NiO nanoparticles with controllable size. Black-Right-Pointing-Pointer High specific surface area for NiO nanoparticles with size range from 3 to 7 nm. Black-Right-Pointing-Pointer Strong reduction of the thermal conductivity with decreasing particle size. Black-Right-Pointing-Pointer NiO as nanoinclusions in high performance materials for energy conversion.

Microstructure and thermal conductivity of surfactant-free NiO nanostructures

International Nuclear Information System (INIS)

Sahoo, Pranati; Misra, Dinesh K.; Salvador, Jim; Makongo, Julien P.A.; Chaubey, Girija S.; Takas, Nathan J.; Wiley, John B.; Poudeu, Pierre F.P.

2012-01-01

High purity, nanometer sized surfactant-free nickel oxide (NiO) particles were produced in gram scale using a solution combustion method and characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), gas pycnometry and gas adsorption analysis (BET). The average particle size of the as-synthesized NiO increases significantly with the preheating temperature of the furnace, while the specific surface area decreases. A BET specific surface area of ∼100 m 2 /g was obtained for NiO nanoparticles with size as small as 3 nm synthesized at 300 °C. The thermal conductivity (κ) of pressed pellets of the synthesized NiO nanoparticles obtained using spark plasma sintering (SPS) and uniaxial hot pressing is drastically decreased (∼60%) compared to that of NiO single crystal. This strong reduction in κ with particle size suggests the suitability of the synthesized surfactant-free NiO nanoparticles for use as nanoinclusions when designing high performance materials for waste heat recovery. - Graphical abstract: Highly efficient phonon scattering by surfactant-free NiO nanostructures obtained by solution combustion of a mixture of nickel (II) nitrate hexahydrate (oxidizer) and urea (fuel) at various temperatures. Highlights: ► Fast synthesis of surfactant-free NiO nanoparticles with controllable size. ► High specific surface area for NiO nanoparticles with size range from 3 to 7 nm. ► Strong reduction of the thermal conductivity with decreasing particle size. ► NiO as nanoinclusions in high performance materials for energy conversion.

Thickness dependent ferromagnetism in thermally decomposed NiO thin films

Energy Technology Data Exchange (ETDEWEB)

Ravikumar, Patta; Kisan, Bhagaban; Perumal, Alagarsamy, E-mail: perumal@iitg.ernet.in

2016-11-15

We report the effects of film thickness, annealing temperature and annealing environments on thermal decomposition behavior and resulting magnetic properties of NiO (t=50–300 nm) thin films. All the NiO films were prepared directly on thermally oxidized Si at ambient temperature using magnetron sputtering technique and post annealed at different temperatures (T{sub A}) under vacuum and oxygen atmospheres. As-deposited films exhibit face centered cubic structure with large lattice constant due to strain induced during sputtering process. With increasing T{sub A}, the lattice constant decreases due to the release of strain and thickness dependent thermal decomposition reaction of NiO into Ni has been observed for the NiO films annealed at 500 °C under vacuum condition. As a result, the antiferromagnetic nature of the as-deposited NiO films transforms into ferromagnetic one with dominant thickness dependent ferromagnetic behavior at room temperature. In addition, the existence of both Ni and NiO phases in the annealed NiO films shows noticeable exchange bias under field cooling condition. The behavior of thermal decomposition was not observed for the NiO films annealed under oxygen condition which results in no detectable change in the magnetic properties. The observed results are discussed on the basis of thickness dependent thermal decomposition in NiO films with increasing T{sub A} and changing annealing conditions. - Highlights: • Preparation of highly strained single layer NiO films with different thicknesses. • Study the effects of annealing under different environments on crystal structure. • Understanding the origin of thickness dependent thermal decomposition reaction. • Investigate the role of thermal decomposition reaction on the magnetic properties. • Study the interaction between NiO and Ni phases on the exchange bias mechanism.

The effect of oxygen transfer mechanism on the cathode performance based on proton-conducting solid oxide fuel cells

KAUST Repository

Hou, Jie

2015-01-01

Two types of proton-blocking composites, La2NiO4+δ-LaNi0.6Fe0.4O3-δ (LNO-LNF) and Sm0.2Ce0.8O2-δ-LaNi0.6Fe0.4O3-δ (SDC-LNF), were evaluated as cathode materials for proton-conducting solid oxide fuel cells (H-SOFCs) based on the BaZr0.1Ce0.7Y0.2O3-δ (BZCY) electrolyte, in order to compare and investigate the influence of two different oxygen transfer mechanism on the performance of the cathode for H-SOFCs. The X-ray diffraction (XRD) results showed that the chemical compatibility of the components in both compounds was excellent up to 1000°C. Electrochemical studies revealed that LNO-LNF showed lower area specific polarization resistances in symmetrical cells and better electrochemical performance in single cell tests. The single cell with LNO-LNF cathode generated remarkable higher maximum power densities (MPDs) and lower interfacial polarization resistances (Rp) than that with SDC-LNF cathode. Correspondingly, the MPDs of the single cell with the LNO-LNF cathode were 490, 364, 266, 180 mW cm-2 and the Rp were 0.103, 0.279, 0.587, 1.367 Ω cm2 at 700, 650, 600 and 550°C, respectively. Moreover, after the single cell with LNO-LNF cathode optimized with an anode functional layer (AFL) between the anode and electrolyte, the power outputs reached 708 mW cm-2 at 700°C. These results demonstrate that the LNO-LNF composite cathode with the interstitial oxygen transfer mechanism is a more preferable alternative for H-SOFCs than SDC-LNF composite cathode with the oxygen vacancy transfer mechanism.

An EIS study of La2-aEuro parts per thousand x Sr (x) NiO4+ (delta) SOFC cathodes

DEFF Research Database (Denmark)

Kammer Hansen, Kent

2009-01-01

nickelates towards the reduction of oxygen is equal to the ASR of perovskites; however, it is not as low as for the best Fe–Co-based perovskites. The lowest ASR is found for the compound La1.75Sr0.25NiO4 +  δ with an ASR of 23.8 Ωcm2 measured on a cone-shaped electrode in air at 600 °C. It is suggested...

Hydrothermal-synthesized NiO nanowall array for lithium ion batteries

International Nuclear Information System (INIS)

Yan, Xiaoyan; Tong, Xili; Wang, Jian; Gong, Changwei; Zhang, Mingang; Liang, Liping

2013-01-01

Graphical abstract: Freestanding NiO nanowall array is prepared via a hydrothermal synthesis method and shows noticeable Li battery performance with good cycle life and high capacity. Highlights: ► NiO nanowall array is prepared by a hydrothermal synthesis method. ► NiO nanowall array with high capacity as anode material for Li ion battery. ► Nanowall array structure is favorable for fast ion/electron transfer. -- Abstract: We report a self-supported NiO nanowall array prepared by a facile hydrothermal synthesis method. The microstructure and morphology of the sample are characterized by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The hydrothermal-synthesized NiO nanowalls with thicknesses of ∼20 nm arrange vertically to the substrate forming a net-like nanowall array structure. As anode material for lithium ion batteries, the NiO nanowall array exhibits better electrochemical performances with higher coulombic efficiency and better cycling performance as compared to the dense NiO film. The NiO nanowall array shows an initial coulombic efficiency of 76%, as well as good cycling stability with a capacity of 567 mAh g −1 at 0.3 A g −1 after 50 cycles, higher than those of the dense polycrystalline NiO film (361 mAh g −1 ). The superior electrochemical performance is mainly due to the unique nanowall array structure with shorter diffusion length for mass and charge transport

Development and testing of anode-supported solid oxide fuel cells with slurry-coated electrolyte and cathode

Energy Technology Data Exchange (ETDEWEB)

Muccillo, R.; Muccillo, E.N.S.; Fonseca, F.C.; Franca, Y.V.; Porfirio, T.C. [Centro de Ciencia e Tecnologia de Materiais, Instituto de Pesquisas Energeticas e Nucleares, C.P. 11049, Pinheiros, S. Paulo, SP 05422-970 (Brazil); de Florio, D.Z. [Instituto de Quimica, UNESP, R. Prof. Francisco Degni s/n, Araraquara, SP 14801-970 (Brazil); Berton, M.A.C.; Garcia, C.M. [Instituto de Tecnologia para o Desenvolvimento, DPMA, C.P. 19067, Curitiba, PR 81531-980 (Brazil)

2006-06-01

A laboratory setup was designed and put into operation for the development of solid oxide fuel cells (SOFCs). The whole project consisted of the preparation of the component materials: anode, cathode and electrolyte, and the buildup of a hydrogen leaking-free sample chamber with platinum leads and current collectors for measuring the electrochemical properties of single SOFCs. Several anode-supported single SOFCs of the type (ZrO{sub 2}:Y{sub 2}O{sub 3}+NiO) thick anode/(ZrO{sub 2}:Y{sub 2}O{sub 3}) thin electrolyte/(La{sub 0.65}Sr{sub 0.35}MnO{sub 3}+ZrO{sub 2}:Y{sub 2}O{sub 3}) thin cathode have been prepared and tested at 700 and 800{sup o}C after in situ H{sub 2} anode reduction. The main results show that the slurry-coating method resulted in single-cells with good reproducibility and reasonable performance, suggesting that this method can be considered for fabrication of SOFCs. (author)

NiO nanosheet assembles for supercapacitor electrode materials

OpenAIRE

Huanhao Xiao; Shunyu Yao; Hongda Liu; Fengyu Qu; Xu Zhang; Xiang Wu

2016-01-01

In this paper, large scale hierarchically assembled NiO nanosheets have been favorably fabricated through a facile hydrothermal route. The as-prepared NiO nanosheet assembles were characterized in detail by various analytical techniques. The results showed these nanosheets present the thickness of about 30 nm and the surface area is 116.9 m2 g−1. These NiO nanosheet assembles were used as the working electrode materials in electrochemical tests, which demonstrated a specific capacitance value...

Defects in codoped NiO with gigantic dielectric response

Science.gov (United States)

Wu, Ping; Ligatchev, Valeri; Yu, Zhi Gen; Zheng, Jianwei; Sullivan, Michael B.; Zeng, Yingzhi

2009-06-01

We combine first-principles, statistical, and phenomenological methods to investigate the electronic and dielectric properties of NiO and clarify the nature of the gigantic dielectric response in codoped NiO. Unlike previous models which are dependent on grain-boundary effects, our model based on small polaron hopping in homogeneous material predicts the dielectric permittivity (104-5) for heavily Li- and MD -codoped NiO (MD=Ti,Al,Si) . Furthermore, we reproduce the experimental trends in dielectric properties as a function of the dopants nature and their concentrations, as well as the reported activation energies for the relaxation in Li- and Ti-codoped NiO (0.308 eV or 0.153 eV depending on the Fermi-level position). In this study, we demonstrate that small polaron hopping on dopant levels is the dominant mechanism for the gigantic dielectric response in these codoped NiO.

Suetônio, dos gramáticos

Directory of Open Access Journals (Sweden)

Marcos Martinho

2014-12-01

Full Text Available O Dos gramáticos de Suetônio divide-se em duas partes: na primeira, o autor narra a introdução, desenvolvimento, florescimento e declínio da gramática em Roma (1-4; na segunda, expõe a biografia de vinte professores de gramática, que ensinaram na Cidade entre o início do séc.  I a.C. e meados do século seguinte (5-24. Quanto à primeira parte, procuro mostrar que Suetônio adota conceitos fisicistas ou naturalistas para narrar a história da gramática em Roma, de modo que aquela se possa comparar à vida de um ser vivo. Assim, a exposição de Suetônio revela-se, na verdade, antes biográfica que historicista. Quanto à segunda parte, procuro mostrar que o Biógrafo se interessa por gramáticos que não só escreveram sobre sua arte no ócio, mas a ensinaram por ofício, isto é, por professores de gramática. Daí, seleciono e comento os elementos narrativos relacionados à docência, a saber: os métodos de ensino, o lugar de ensino, o número e qualidade dos alunos, os preços e honorários dos professores. Por fim, apresento tradução anotada do texto de Suetônio.

Varying the exchange interaction between NiO nanoparticles

DEFF Research Database (Denmark)

Bahl, Christian Robert Haffenden; Mørup, Steen

2006-01-01

We demonstrate that exchange interactions between antiferromagnetic nanoparticles of 57Fe-doped NiO can be varied by simple macroscopic treatments. Mössbauer spectroscopy studies of the superparamagnetic relaxation behaviour show that grinding or suspension in water of nanoparticles of NiO can...

NiO nanosheet assembles for supercapacitor electrode materials

Directory of Open Access Journals (Sweden)

Huanhao Xiao

2016-06-01

Full Text Available In this paper, large scale hierarchically assembled NiO nanosheets have been favorably fabricated through a facile hydrothermal route. The as-prepared NiO nanosheet assembles were characterized in detail by various analytical techniques. The results showed these nanosheets present the thickness of about 30 nm and the surface area is 116.9 m2 g−1. These NiO nanosheet assembles were used as the working electrode materials in electrochemical tests, which demonstrated a specific capacitance value of 81.67 F g−1 at the current density of 0.5 A g−1 and excellent long cycle-life stability with 78.5% of its discharge specific capacitance retention after 3000 cycles at the current density of 0.5 A g−1, revealing the as-synthesized NiO nanosheet assembles might be a promising electrode material for supercapacitor applications.

Cation exchange removal of Cd from aqueous solution by NiO

International Nuclear Information System (INIS)

Mahmood, T.; Saddique, M.T.; Naeem, A.; Mustafa, S.; Dilara, B.; Raza, Z.A.

2011-01-01

Graphical abstract: Sorption of Cd on NiO particles is described by modified Langmuir adsorption isotherms. - Abstract: Detailed adsorption experiments of Cd from aqueous solution on NiO were conducted under batch process with different concentrations of Cd, time and temperature of the suspension. The solution pH is found to play a decisive role in the metal ions precipitation, surface dissolution and adsorption of metal ions onto the NiO. Preliminary adsorption experiments show that the selectivity of NiO towards different divalent metal ions follows the trend Pb > Zn > Co > Cd, which is related to their first hydrolysis equilibrium constant. The exchange between the proton from the NiO surface and the metal from solution is responsible for the adsorption. The cation/exchange mechanism essentially remains the same for Pb, Zn, Co and Cd ions. The sorption of Cd on NiO particles is described by the modified Langmuir adsorption isotherms. The isosteric heat of adsorption (ΔH) indicates the endothermic nature of the cation exchange process. Spectroscopic analyses provide evidence that Cd is chemisorbed onto the surface of NiO.

Synthesis and characterization of NiO nanoparticles by Pechini method; Sintese e caracterizacao de nanoparticulas de NiO pelo metodo Pechini

Energy Technology Data Exchange (ETDEWEB)

Nascimento, A; Ribeiro, M A; Costa, A C.F.M.; Gama, L [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Dept. de Engenharia de Materiais; Bernardi, M I.B. [Universidade de Sao Paulo (IFSC/USP), Sao Carlos, SP (Brazil). Inst. de Fisica

2009-07-01

In recent years, ultrafine magnetic particles of NiO have attracting the attention because of its unknown behavior, enormous scientific potential and technological application. Some of its more important properties are accented magnetic moments, double dynamic exchange, quantization of wave of spin and etc. In this context, this work has for objective to synthesize and to characterize nanoparticles of NiO for the Pechini method. The powder was analyzed by X-rays diffraction. The results of scanning electron microscopy, adsorption of nitrogen. The analysis of X-rays diffraction of the sample showed single-phase peaks of NiO, with crystallite size close to 38 nm. The surface area was 6.44 m{sup 2}/g. The image from scanning electron microscopy shows soft homogeneous agglomerates. The Pechini synthesis was efficient in the production of powders of NiO nano metrics and single-phase. (author)

Effect of gamma-irradiation on some structural characteristics of NiO

International Nuclear Information System (INIS)

El-Shabiny, A.M.; El-Shobaky, G.A.; Dessouki, A.M.; Ramadan, A.A.

1989-01-01

Pure NiO specimens were prepared by the thermal decomposition of pure basic nickel carbonate in air at 400 and 600 0 C. The obtained solids were exposed to different doses of γ-irradiation ranging between 10-80 Mrad. The change in residual microstrain, lattice parameter and crystallite size due to the irradiation process were investigated by X-ray diffraction analyses. The results revealed that γ-irradiation effected important changes in the structural characteristics of NiO lattice. No detectable change was observed for the crystallite size of NiO-400 0 C; however, the crystallite size of NiO-600 0 C decreased by increasing the dose up to 20 Mrad and increased at higher doses but still remaining smaller than that measured for the unirradiated specimen. The lattice parameters of NiO preheated at 400 or 600 0 C were found to increase as a function of the dose. These results were attributed to progressive removal of Ni 3+ ions acting as lattice defects in NiO solid. The microstrains in NiO specimens precalcined either at 400 or 600 0 C were found to decrease progressively by increasing the dose falling to minimum values at doses of 40 and 80 Mrad for the solids preheated at 600 and 400 0 C, respectively. The augmentation of the exposure dose above 40 Mrad for NiO-600 0 C resulted in an increase in microstrain which, however, remained always smaller than those found for the unirradiated solid. The strain-relief in NiO-600 0 C due to γ-irradiation took place, mainly, via splitting of its crystallites. On the other hand, the progressive removal of lattice defects (Ni 3+ ions) due to the irradiation process might account for the observed strain-relief in NiO-400 0 C. (author)

Surface properties of nanostructured NiO undergoing electrochemical oxidation in 3-methoxy-propionitrile

International Nuclear Information System (INIS)

Bonomo, Matteo; Marrani, Andrea Giacomo; Novelli, Vittoria; Awais, Muhammad; Dowling, Denis P.; Vos, Johannes G.; Dini, Danilo

2017-01-01

Highlights: • NiO porous thin films were prepared via RDS technique. • NiO electrodes were characterized in a nitrile based electrochemical cell. • NiO electrodes were studied by means of XPS. • The XP spectra excluded the formation of phases other than NiO. • The presence of ClO 4 − as charge balancing species was evidenced. - Abstract: Nanostructured nickel oxide (NiO) was deposited in the configuration of thin film (thickness, l = 2–6 μm) onto fluorine-doped tin oxide (FTO) substrates via plasma-assisted rapid discharge sintering (RDS). Electrochemical cycling of RDS NiO in 3-methoxy-propionitrile (3-MPN) revealed two characteristic peaks of NiO oxidation which were associated to the surface-confined redox processes Ni(II) → Ni(III) and Ni(III) → Ni(IV). Grazing angle X-ray photoelectron spectroscopy (XPS) was conducted ex-situ on NiO electrodes in both pristine and oxidized states. Oxidized NiO samples for XPS experiments were obtained in the potentiostatic mode through the polarization of NiO at its two characteristic potentials of oxidation. The XPS analysis allowed to ascertain the electronic structure of the nanoporous NiO framework, and verify the adsorption of perchlorate and chloride anions onto NiO surface due to the compensation of the charge stored in oxidized NiO. XPS also revealed that the spectrum within the region characteristic of Ni 2p ionization does not vary considerably with the state of charge of the nickel centres. This finding is in evident contrast to what has been observed for the same system when it undergoes electrochemical oxidation in aqueous electrolyte.

Surface properties of nanostructured NiO undergoing electrochemical oxidation in 3-methoxy-propionitrile

Energy Technology Data Exchange (ETDEWEB)

Bonomo, Matteo [Department of Chemistry, University of Rome “La Sapienza”, Piazzale Aldo Moro 5, 00185 Rome (Italy); Marrani, Andrea Giacomo, E-mail: andrea.marrani@uniroma1.it [Department of Chemistry, University of Rome “La Sapienza”, Piazzale Aldo Moro 5, 00185 Rome (Italy); Novelli, Vittoria [Department of Chemistry, University of Rome “La Sapienza”, Piazzale Aldo Moro 5, 00185 Rome (Italy); Awais, Muhammad [Department of Industrial Engineering, “King Abdulaziz” University, Rabigh (Saudi Arabia); Solar Energy Conversion Strategic Research Cluster, University College Dublin (UCD), Belfield, Dublin 4 (Ireland); Dowling, Denis P. [Solar Energy Conversion Strategic Research Cluster, University College Dublin (UCD), Belfield, Dublin 4 (Ireland); School of Mechanical and Materials Engineering, University College Dublin (UCD), Belfield, Dublin 4 (Ireland); Vos, Johannes G. [School of Chemical Sciences, Dublin City University (DCU), Glasnevin, Dublin 9 (Ireland); Dini, Danilo [Department of Chemistry, University of Rome “La Sapienza”, Piazzale Aldo Moro 5, 00185 Rome (Italy); Solar Energy Conversion Strategic Research Cluster, University College Dublin (UCD), Belfield, Dublin 4 (Ireland)

2017-05-01

Highlights: • NiO porous thin films were prepared via RDS technique. • NiO electrodes were characterized in a nitrile based electrochemical cell. • NiO electrodes were studied by means of XPS. • The XP spectra excluded the formation of phases other than NiO. • The presence of ClO{sub 4}{sup −} as charge balancing species was evidenced. - Abstract: Nanostructured nickel oxide (NiO) was deposited in the configuration of thin film (thickness, l = 2–6 μm) onto fluorine-doped tin oxide (FTO) substrates via plasma-assisted rapid discharge sintering (RDS). Electrochemical cycling of RDS NiO in 3-methoxy-propionitrile (3-MPN) revealed two characteristic peaks of NiO oxidation which were associated to the surface-confined redox processes Ni(II) → Ni(III) and Ni(III) → Ni(IV). Grazing angle X-ray photoelectron spectroscopy (XPS) was conducted ex-situ on NiO electrodes in both pristine and oxidized states. Oxidized NiO samples for XPS experiments were obtained in the potentiostatic mode through the polarization of NiO at its two characteristic potentials of oxidation. The XPS analysis allowed to ascertain the electronic structure of the nanoporous NiO framework, and verify the adsorption of perchlorate and chloride anions onto NiO surface due to the compensation of the charge stored in oxidized NiO. XPS also revealed that the spectrum within the region characteristic of Ni 2p ionization does not vary considerably with the state of charge of the nickel centres. This finding is in evident contrast to what has been observed for the same system when it undergoes electrochemical oxidation in aqueous electrolyte.

Do patrimônio cultural e seus significados

Directory of Open Access Journals (Sweden)

Fátima Maria Alencar Araripe

Full Text Available Reflexões acerca do patrimônio cultural tendo em mente o conjunto de tudo o que encontramos na formação da cultura: conhecimento, crenças, arte, moral, direitos, costumes, capacidade e hábitos adquiridos pelo homem, transmitidos de geração a geração e a dimensão da força simbólica do seu significado, como representação da expressão cultural do fazer social. Propõe (redefinir o patrimônio cultural, como memória social e, por conseguinte, parte da história, na possibilidade de pensar esse patrimônio parte de um grande acervo informacional, isto é, como fonte de informação, inserido nos processos de ensino e de pesquisa, de forma a possibilitar a construção de um ser socialmente ativo. Este ser, ao unir passado e presente, (recria imagens da cidade _ espaço por excelência da formação do patrimônio, do povo e da cultura, observando as condições históricas, sociais e comunicacionais, bem como as exigências contemporâneas, que levam em consideração a produção humana como bem cultural e, portanto, da maior significação. Este ensaio apresenta o patrimônio cultural desde a perspectiva dos usos sociais, das apropriações que a sociedade faz da sua memória, da sua história, para que haja reconhecimento e legitimação desse patrimônio que, conseqüentemente, será elemento a permear o processo educacional e formação da cidadania.

Electronic and optical properties of antiferromagnetic iron doped NiO - A first principles study

Science.gov (United States)

Petersen, John E.; Twagirayezu, Fidele; Scolfaro, Luisa M.; Borges, Pablo D.; Geerts, Wilhelmus J.

2017-05-01

Antiferromagnetic NiO is a candidate for next generation high-speed and scaled RRAM devices. Here, electronic and optical properties of antiferromagnetic NiO: Fe 25% in the rock salt structure are studied and compared to intrinsic NiO. From density of states and complex dielectric function analysis, the first optical transition is found to be at lower frequency than intrinsic NiO due to an Fe impurity level being the valence band maximum. The resulting effects on refractive index, reflectivity, absorption, optical conductivity and loss function for Fe-doped NiO are compared to those of intrinsic NiO, and notable differences are analyzed. The electronic component of the static dielectric constant of NiO: Fe 25% is calculated to be about 2% less than that of intrinsic NiO.

Comparison of the Pulmonary Oxidative Stress Caused by Intratracheal Instillation and Inhalation of NiO Nanoparticles when Equivalent Amounts of NiO Are Retained in the Lung

Directory of Open Access Journals (Sweden)

Masanori Horie

2016-01-01

Full Text Available NiO nanoparticles were administered to rat lungs via intratracheal instillation or inhalation. During pulmonary toxicity caused by NiO nanoparticles, the induction of oxidative stress is a major factor. Both intratracheal instillation and inhalation of NiO nanoparticles induced pulmonary oxidative stress. The oxidative stress response protein, heme oxygenase-1 (HO-1, was induced by the administration of NiO nanoparticles at both the protein and gene expression level. Additionally, certain oxidative-stress markers in the lung, such as 8-iso-prostaglandin F2α, thioredoxin, and inducible nitric oxide synthase were increased. Furthermore, the concentration of myeloperoxidase (MPO in the lung was also increased by the administration of NiO nanoparticles. When the amount of NiO in the lung is similar, the responses against pulmonary oxidative stress of intratracheal instillation and inhalation are also similar. However, the state of pulmonary oxidative stress in the early phase was different between intratracheal instillation and inhalation, even if the amount of NiO in the lung was similar. Inhalation causes milder oxidative stress than that caused by intratracheal instillation. On evaluation of the nanoparticle-induced pulmonary oxidative stress in the early phase, we should understand the different states of oxidative stress induced by intratracheal instillation and inhalation.

Influence of NiO concentration on structural, dielectric and magnetic properties of core/shell CuFe{sub 2}O{sub 4}/NiO nanocomposites

Energy Technology Data Exchange (ETDEWEB)

Ali, Kashif [Department of Physics, International Islamic University, Islamabad (Pakistan); Iqbal, Javed, E-mail: javed.saggu@qau.edu.pk [Laboratory of Nanoscience and Technology (LNT), Department of Physics, Quaid-i-Azam University, Islamabad (Pakistan); Jan, Tariq [Department of Physics, University of Lahore, Sargodha Campus, Sargodha (Pakistan); Ahmad, Ishaq [Experimental Physics Labs, National Center for Physics, Islamabad (Pakistan); Wan, Dongyun [School of Materials Science and Engineering, Shanghai University, Shanghai 200444 (China); Ahmad, Ijaz [Department of Chemistry, Allama Iqbal Open University, Islamabad (Pakistan)

2017-07-01

Nanocomposites of (1-x)CuFe{sub 2}O{sub 4}/xNiO (x = 10% to 50 wt %) have been synthesized utilizing a chemical co-precipitation method. In order to obtain the required phase, the samples have been annealed at 600 °C for 6 h. The x-ray Diffraction (XRD) technique has been used for the crystallographic structure analysis which not only confirms the coexistent of both copper ferrite (CuFe{sub 2}O{sub 4}) and nickel oxide (NiO) phases in all samples but also verifies the absence of any impurity phases. The average crystallite size as estimated via XRD patterns show that the average size lies in the range of 22–36 nm which has also been confirmed by TEM. The FTIR absorbance spectra also show the characteristic vibration modes of cation at tetrahedral and octahedral sites. The electrical properties like A.C. conductivity, impedance, Dielectric constant, and Tangent loss has been measured by LCR meter. The results show that with the increase in NiO concentration, electrical conductivity increases for all concentration while dielectric constant decreases up to 30% NiO wt% and increases with further addition of NiO. The real and imaginary parts of impedance depict same dispersion i.e the impedance decreases at higher frequency due to increase in conductivity. Moreover the magnetic characterizations performed by VSM, reveal that the hysteresis loops exhibit normal behavior of ferromagnetic/ferrimagnetic materials for all compositions but the coercivity (H{sub c}), and saturation magnetization (M{sub s}) decreases with the increase in NiO contents that transform the material in to soft magnetic. - Highlights: • This novel core/shell nanocomposite synthesized by a facile wet chemical route. • The decrease in coercivity with NiO contents is due to pinning of moments at surface. • Increase in NiO contents makes CuFe{sub 2}O{sub 4} a high dielectric loss material. • The antiferromagnetic nature of NiO shift CuFe{sub 2}O{sub 4} toward a soft magnetic material.

Surface properties of nanostructured NiO undergoing electrochemical oxidation in 3-methoxy-propionitrile

Science.gov (United States)

Bonomo, Matteo; Marrani, Andrea Giacomo; Novelli, Vittoria; Awais, Muhammad; Dowling, Denis P.; Vos, Johannes G.; Dini, Danilo

2017-05-01

Nanostructured nickel oxide (NiO) was deposited in the configuration of thin film (thickness, l = 2-6 μm) onto fluorine-doped tin oxide (FTO) substrates via plasma-assisted rapid discharge sintering (RDS). Electrochemical cycling of RDS NiO in 3-methoxy-propionitrile (3-MPN) revealed two characteristic peaks of NiO oxidation which were associated to the surface-confined redox processes Ni(II) → Ni(III) and Ni(III) → Ni(IV). Grazing angle X-ray photoelectron spectroscopy (XPS) was conducted ex-situ on NiO electrodes in both pristine and oxidized states. Oxidized NiO samples for XPS experiments were obtained in the potentiostatic mode through the polarization of NiO at its two characteristic potentials of oxidation. The XPS analysis allowed to ascertain the electronic structure of the nanoporous NiO framework, and verify the adsorption of perchlorate and chloride anions onto NiO surface due to the compensation of the charge stored in oxidized NiO. XPS also revealed that the spectrum within the region characteristic of Ni 2p ionization does not vary considerably with the state of charge of the nickel centres. This finding is in evident contrast to what has been observed for the same system when it undergoes electrochemical oxidation in aqueous electrolyte.

An approach for longer lifetime MCFCs

Energy Technology Data Exchange (ETDEWEB)

Matsumoto, Masaru; Tatsumi, Masahiko; Hayano, Takuro [MCFC Research Association, Tokyo (Japan)] [and others

1996-12-31

For entering into commercialization of MCFC power plants in the beginning of the 21st century, we will devote to research for increasing lifetime as long as 40,000 hours with cell performance decay rate of 0.25 %/1000hrs as the target in FY 1999. This paper will discuss on our approach for longer lifetime MCFCs through electrolyte-loss management and NiO precipitation management as well as micro-structural control of electrodes and matrix plates. Cell voltage decay rate will be estimated by simulation through series of experiments on accelerated conditions.

Room temperature ferromagnetism in Mn-doped NiO nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Layek, Samar, E-mail: samarlayek@gmail.com; Verma, H.C.

2016-01-01

Mn-doped NiO nanoparticles of the series Ni{sub 1−x}Mn{sub x}O (x=0.00, 0.02, 0.04 and 0.06) are successfully synthesized using a low temperature hydrothermal method. Samples up to 6% Mn-doping are single phase in nature as observed from powder x-ray diffraction (XRD) studies. Rietveld refinement of the XRD data shows that all the single phase samples crystallize in the NaCl like fcc structure with space group Fm-3m. Unit cell volume decreases with increasing Mn-doping. Pure NiO nanoparticles show weak ferromagnetism, may be due to nanosize nature. Introduction of Mn within NiO lattice improves the magnetic properties significantly. Room temperature ferromagnetism is found in all the doped samples whereas the magnetization is highest for 2% Mn-doping and then decreases with further doping. The ZFC and FC branches in the temperature dependent magnetization separate well above 350 K indicating transition temperature well above room temperature for 2% Mn-doped NiO Nanoparticle. The ferromagnetic Curie temperature is found to be 653 K for the same sample as measured by temperature dependent magnetization study using vibrating sample magnetometer (VSM) in high vacuum. - Highlights: • Mn-doped NiO nanoparticles are prepared by a simple hydrothermal method. • Unit cell volume decreases with increasing doping concentration. • Mn-doping leads to room temperature ferromagnetism in NiO nanoparticles. • Magnetization is highest for 2% Mn-doping. • Above 2%, magnetization decreases with increasing doping.

Room temperature ferromagnetism in Mn-doped NiO nanoparticles

International Nuclear Information System (INIS)

Layek, Samar; Verma, H.C.

2016-01-01

Mn-doped NiO nanoparticles of the series Ni_1_−_xMn_xO (x=0.00, 0.02, 0.04 and 0.06) are successfully synthesized using a low temperature hydrothermal method. Samples up to 6% Mn-doping are single phase in nature as observed from powder x-ray diffraction (XRD) studies. Rietveld refinement of the XRD data shows that all the single phase samples crystallize in the NaCl like fcc structure with space group Fm-3m. Unit cell volume decreases with increasing Mn-doping. Pure NiO nanoparticles show weak ferromagnetism, may be due to nanosize nature. Introduction of Mn within NiO lattice improves the magnetic properties significantly. Room temperature ferromagnetism is found in all the doped samples whereas the magnetization is highest for 2% Mn-doping and then decreases with further doping. The ZFC and FC branches in the temperature dependent magnetization separate well above 350 K indicating transition temperature well above room temperature for 2% Mn-doped NiO Nanoparticle. The ferromagnetic Curie temperature is found to be 653 K for the same sample as measured by temperature dependent magnetization study using vibrating sample magnetometer (VSM) in high vacuum. - Highlights: • Mn-doped NiO nanoparticles are prepared by a simple hydrothermal method. • Unit cell volume decreases with increasing doping concentration. • Mn-doping leads to room temperature ferromagnetism in NiO nanoparticles. • Magnetization is highest for 2% Mn-doping. • Above 2%, magnetization decreases with increasing doping.

Fabrication of NiO nanoflakes and its application in lithium ion battery

International Nuclear Information System (INIS)

Ni Shibing; Li Tao; Yang Xuelin

2012-01-01

Highlights: ► In this study we develop a simple two-step method to fabricate NiO nanoflakes. ► We study the electrochemical properties of the NiO nanoflakes as anode material of lithium ion batteries. ► NiO nanoflakes show high capacity at low current density and excellent cycle performance at high current density. ► In this study we conclude that NiO nanoflakes have potential applications in lithium ion batteries. - Abstract: NiO nanoflakes with mean size about 2 μm and mean thickness about 20 nm have been successfully synthesized via a simple two-step method. Electrochemical properties of the as-synthesized NiO nanoflakes as anode electrode of lithium ion batteries were studied by conventional charge/discharge tests, showing initial discharge and charge capacities of 1213 mAh g −1 and 902 mAh g −1 at a current density of 100 mA g −1 . After 50 cycles, the discharge and charge capacities of NiO nanoflakes electrode were 1015 and 990 mAh g −1 , respectively. The first discharge and charge capacities of the as-prepared NiO electrode were 749 and 541 mAh g −1 at a current density of 800 mA g −1 , being of 578 and 567 mAh g −1 after 50 cycles.

Electronic structures of N- and C-doped NiO from first-principles calculations

International Nuclear Information System (INIS)

Long, Run; English, Niall J.; Mooney, Damian A.

2010-01-01

The large intrinsic band gap of NiO has hindered severely its potential application under visible-light irradiation. In this Letter, we have performed first-principles calculations on the electronic properties of N- and C-doped NiO to ascertain if its band gap may be narrowed theoretically. It was found that impurity bands driven by N 2p or C 2p states appear in the band gap of NiO and that some of these locate at the conduction band minimum, which leads to a significant band gap narrowing. Our results show that N-doped NiO may serve as a potential photocatalyst relative to C-doped NiO, due to the presence of some recombination centres in C-doped NiO.

Magnetic anomalies in Fe-doped NiO nanoparticle

Science.gov (United States)

Pradeep, R.; Gandhi, A. C.; Tejabhiram, Y.; Mathar Sahib, I. K. Md; Shimura, Y.; Karmakar, L.; Das, D.; Wu, Sheng Yun; Hayakawa, Y.

2017-09-01

Undoped and iron-doped NiO nanoparticle were synthesized by standard hydrothermal method. A detailed study is carried out on the effect of dopant concentration on morphology, structural, resonance and magnetic properties of NiO nanoparticle by varying the Fe concentration from 0.01 to 0.10 M. The synchrotron-x-ray diffraction confirmed that no secondary phase was observed other than NiO. The x-ray photoelectron spectroscopy studies revealed that, Fe was primarily in the trivalent state, replacing the Ni2+ ion inside the octahedral crystal site of NiO. The Electron paramagnetic studies revealed the ferromagnetic cluster formation at high doping concentration (5 and 10%). The ZFC-FC curves displayed an average blocking temperature around 180 K due to particle size distribution. The anomalous behaviour of spontaneous exchange bias (H SEB) and magnetic remanence (M r) for all Fe-doped samples observed at 5 K showed an increase (0.1316-0.1384 emu g-1) in the moment of frozen spin (M p) as the dopant concentration increased. The role of frozen spin moment in spontaneous exchange bias behaviour was discussed.

Fundamental absorption edge of NiO nanocrystals

Energy Technology Data Exchange (ETDEWEB)

Sokolov, V.I., E-mail: visokolov@imp.uran.ru [Institute of Metal Physics, Ural Branch of RAS, S. Kovalevskaya Street 18, 620990 Yekaterinburg (Russian Federation); Druzhinin, A.V. [Institute of Metal Physics, Ural Branch of RAS, S. Kovalevskaya Street 18, 620990 Yekaterinburg (Russian Federation); Kim, G.A. [Institute of Organic Synthesis Ural Branch of RAS, S. Kovalevskaya Street 20, 620990 Yekaterinburg (Russian Federation); Gruzdev, N.B.; Yermakov, A.Ye.; Uimin, M.A.; Byzov, I.V.; Shchegoleva, N.N.; Vykhodets, V.B.; Kurennykh, T.E. [Institute of Metal Physics, Ural Branch of RAS, S. Kovalevskaya Street 18, 620990 Yekaterinburg (Russian Federation)

2013-12-01

NiO nanocrystals with the average size of 5, 10 and 25 nm were synthesized by gas-condensation method. The well-defined increase of the optical density D near the fundamental absorption edge of NiO nanocrystals in the range of 3.5–4.0 eV observed after the annealing in air is caused by the oxygen content growth. It is the direct experimental evidence of the fact that p—d charge transfer transitions form the fundamental absorption edge.

Fundamental absorption edge of NiO nanocrystals

International Nuclear Information System (INIS)

Sokolov, V.I.; Druzhinin, A.V.; Kim, G.A.; Gruzdev, N.B.; Yermakov, A.Ye.; Uimin, M.A.; Byzov, I.V.; Shchegoleva, N.N.; Vykhodets, V.B.; Kurennykh, T.E.

2013-01-01

NiO nanocrystals with the average size of 5, 10 and 25 nm were synthesized by gas-condensation method. The well-defined increase of the optical density D near the fundamental absorption edge of NiO nanocrystals in the range of 3.5–4.0 eV observed after the annealing in air is caused by the oxygen content growth. It is the direct experimental evidence of the fact that p—d charge transfer transitions form the fundamental absorption edge

Synthesis and characterization of NiO nanopowder by sol-gel process

Energy Technology Data Exchange (ETDEWEB)

Ningsih, Sherly Kasuma Warda [Department of Chemistry, Faculty of Mathematics and Natural Sciences Padang State University, Kampus Air Tawar, Jl. Prof. Dr. Hamka, West Sumatera, 25161, Indonesia Email: sherly-kasuma@yahoo.com (Indonesia)

2015-09-30

Preparation of nickel oxide (NiO) nanopowder by sol-gel process has been studied. NiO nanopowders were obtained by sol-gel method by using nickel nitrate hexahydrate and sodium hydroxide and aquadest were used as precursor, agent precipitator and solvent, respectively. The powders were formed by drying at 110°C and followed by heating in the furnace at 400°C for 1.5 hours. The product was obtained black powder. The product was characterized by Energy Dispesive X-ray Fluorescence (ED-XRF), X-ray diffraction (XRD) and Scanning Electron Microscopy (SEM). The ED-XRF pattern shows the composition of NiO produced was 97.1%. The XRD pattern showed NiO forms were produced generally in monoclinic stucture. The crystalline size of NiO was obtained in the range 40-85 nm. SEM micrograph clearly showed that powder had a spherical with uniform distribution size is 0.1-1.0 µm approximately.

Exchange bias in finite sized NiO nanoparticles with Ni clusters

International Nuclear Information System (INIS)

Gandhi, Ashish Chhaganlal; Lin, Jauyn Grace

2017-01-01

Structural and magnetic properties of finite sized NiO nanoparticles are investigated with synchrotron X-ray diffraction (XRD), transmission electron microscopy, magnetometer and ferromagnetic resonance (FMR) spectroscopy. A minor Ni phase is detected with synchrotron XRD, attributed to the oxygen defects in the NiO core. A considerable exchange bias of ~100 Oe is observed at 50 K and it drops abruptly and vanishes above 150 K, in association with the reduction of frozen spins. FMR data indicate a strong interaction between ferromagnetic (FM) and antiferromagnetic (AFM) phases below 150 K, consistent with the picture of isolated FM clusters in AFM matrix. - Highlights: • Structural and magnetic properties of finite sized NiO nanoparticles are systematically investigated with several advanced techniques. • A strong interaction between ferromagnetic and antiferromagnetic phases is found below 150 K. • Exchange bias field in finite sized NiO nanoparticles is due to anisotropy energy of Ni clusters over riding the domain wall energy of NiO.

Exchange bias in finite sized NiO nanoparticles with Ni clusters

Energy Technology Data Exchange (ETDEWEB)

Gandhi, Ashish Chhaganlal; Lin, Jauyn Grace, E-mail: jglin@ntu.edu.tw

2017-02-15

Structural and magnetic properties of finite sized NiO nanoparticles are investigated with synchrotron X-ray diffraction (XRD), transmission electron microscopy, magnetometer and ferromagnetic resonance (FMR) spectroscopy. A minor Ni phase is detected with synchrotron XRD, attributed to the oxygen defects in the NiO core. A considerable exchange bias of ~100 Oe is observed at 50 K and it drops abruptly and vanishes above 150 K, in association with the reduction of frozen spins. FMR data indicate a strong interaction between ferromagnetic (FM) and antiferromagnetic (AFM) phases below 150 K, consistent with the picture of isolated FM clusters in AFM matrix. - Highlights: • Structural and magnetic properties of finite sized NiO nanoparticles are systematically investigated with several advanced techniques. • A strong interaction between ferromagnetic and antiferromagnetic phases is found below 150 K. • Exchange bias field in finite sized NiO nanoparticles is due to anisotropy energy of Ni clusters over riding the domain wall energy of NiO.

Synthesis and characterization of NiO nanoparticles by Pechini method

International Nuclear Information System (INIS)

Nascimento, A.; Ribeiro, M.A.; Costa, A.C.F.M.; Gama, L.; Bernardi, M.I.B.

2009-01-01

In recent years, ultrafine magnetic particles of NiO have attracting the attention because of its unknown behavior, enormous scientific potential and technological application. Some of its more important properties are accented magnetic moments, double dynamic exchange, quantization of wave of spin and etc. In this context, this work has for objective to synthesize and to characterize nanoparticles of NiO for the Pechini method. The powder was analyzed by X-rays diffraction. The results of scanning electron microscopy, adsorption of nitrogen. The analysis of X-rays diffraction of the sample showed single-phase peaks of NiO, with crystallite size close to 38 nm. The surface area was 6.44 m 2 /g. The image from scanning electron microscopy shows soft homogeneous agglomerates. The Pechini synthesis was efficient in the production of powders of NiO nano metrics and single-phase. (author)

Effects of Co{sup 2+} doping on physicochemical behaviors of hierarchical NiO nanostructure

Energy Technology Data Exchange (ETDEWEB)

Ding, Caihua [Beijing Key Laboratory of Construction Tailorable Advanced Functional Materials and Green Applications, School of Materials Science & Engineering, Beijing Institute of Technology, Beijing, 100081 (China); Gao, WenChao [College of Engineering, Peking University, Beijing, 100871 (China); Zhao, Yongjie, E-mail: zhaoyjpeace@gmail.com [Beijing Key Laboratory of Construction Tailorable Advanced Functional Materials and Green Applications, School of Materials Science & Engineering, Beijing Institute of Technology, Beijing, 100081 (China); Zhao, Yuzhen; Zhou, Heping [State Key Laboratory of New Ceramics and Fine Processing, School of Materials Science and Engineering, Tsinghua University, Beijing, 100084 (China); Li, Jingbo; Jin, Haibo [Beijing Key Laboratory of Construction Tailorable Advanced Functional Materials and Green Applications, School of Materials Science & Engineering, Beijing Institute of Technology, Beijing, 100081 (China)

2016-12-30

Highlights: • A series of Co{sup 2+} doped NiO materials were synthesized by a facile hydrothermal method. • Co{sup 2+} doping would bring about a series influence to the as-obtained NiO products. • Hierarchical NiO nanostructure transformed from nanosheets to nanoneedles with Co{sup 2+} doping. • The catalytic properties of NiO were significantly improved via the introduction of Co{sup 2+}. • Excellent catalytic activity was ascribed to the synergistic effect between Co{sup 2+} and NiO. - Abstract: A series of Co{sup 2+} doped NiO materials (Ni{sub 1−x}Co{sub x}O with x = 0, 0.125, 0.25 and 0.5) were synthesized using a facile hydrothermal method followed by a calcination process. The effects of Co{sup 2+} doping on the structural, morphological, magnetic and catalytic properties of NiO were systematically investigated. The results indicated that Co{sup 2+} doping would bring about a series influence to the as-obtained NiO product. The XRD results indicated that within the region of 0 ≤ x ≤ 0.25 the doped products revealed a pure NiO phase. The elementary unit for the hierarchy NiO gradually transformed from nanosheets to nanoneedles with the increase of Co{sup 2+} doping content. As-obtained Co{sup 2+} doped NiO products showed ferromagnetism at room temperature and the magnetization value was increased with the increase of Co{sup 2+} doping content. The catalytic properties of NiO concerning the thermal decomposition of ammonium perchlorate (AP) were significantly improved via the introduction of Co{sup 2+}. The Ni{sub 1−x}Co{sub x}O products with x = 0.25 showed the best catalytic performance to AP, which could decrease the beginning and ending decomposition temperature of AP by 44 and 108 °C. The change of morphology, enhancement of electrical conductivity and the synergistic effect between Co{sup 2+} and NiO were the main factors responsible for the improvement of physicochemical behaviors.

Enhanced room temperature ferromagnetism in antiferromagnetic NiO nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Ravikumar, Patta; Kisan, Bhagaban; Perumal, A., E-mail: perumal@iitg.ernet.in [Department of Physics, Indian institute of Technology Guwahati, Guwahati 781 039 (India)

2015-08-15

We report systematic investigations of structural, vibrational, resonance and magnetic properties of nanoscale NiO powders prepared by ball milling process under different milling speeds for 30 hours of milling. Structural properties revealed that both pure NiO and as-milled NiO powders exhibit face centered cubic structure, but average crystallite size decreases to around 11 nm along with significant increase in strain with increasing milling speed. Vibrational properties show the enhancement in the intensity of one-phonon longitudinal optical (LO) band and disappearance of two-magnon band due to size reduction. In addition, two-phonon LO band exhibits red shift due to size-induced phonon confinement effect and surface relaxation. Pure NiO powder exhibit antiferromagnetic nature, which transforms into induced ferromagnetic after size reduction. The average magnetization at room temperature increases with decreasing the crystallite size and a maximum moment of 0.016 μ{sub B}/f.u. at 12 kOe applied field and coercivity of 170 Oe were obtained for 30 hours milled NiO powders at 600 rotation per minute milling speed. The change in the magnetic properties is also supported by the vibrational properties. Thermomagnetization measurements at high temperature reveal a well-defined magnetic phase transition at high temperature (T{sub C}) around 780 K due to induced ferromagnetic phase. Electron paramagnetic resonance (EPR) studies reveal a good agreement between the EPR results and magnetic properties. The observed results are described on the basis of crystallite size variation, defect density, large strain, oxidation/reduction of Ni and interaction between uncompensated surfaces and particle core with lattice expansion. The obtained results suggest that nanoscale NiO powders with high T{sub C} and moderate magnetic moment at room temperature with cubic structure would be useful to expedite for spintronic devices.

Enhanced room temperature ferromagnetism in antiferromagnetic NiO nanoparticles

Directory of Open Access Journals (Sweden)

Patta Ravikumar

2015-08-01

Full Text Available We report systematic investigations of structural, vibrational, resonance and magnetic properties of nanoscale NiO powders prepared by ball milling process under different milling speeds for 30 hours of milling. Structural properties revealed that both pure NiO and as-milled NiO powders exhibit face centered cubic structure, but average crystallite size decreases to around 11 nm along with significant increase in strain with increasing milling speed. Vibrational properties show the enhancement in the intensity of one-phonon longitudinal optical (LO band and disappearance of two-magnon band due to size reduction. In addition, two-phonon LO band exhibits red shift due to size-induced phonon confinement effect and surface relaxation. Pure NiO powder exhibit antiferromagnetic nature, which transforms into induced ferromagnetic after size reduction. The average magnetization at room temperature increases with decreasing the crystallite size and a maximum moment of 0.016 μB/f.u. at 12 kOe applied field and coercivity of 170 Oe were obtained for 30 hours milled NiO powders at 600 rotation per minute milling speed. The change in the magnetic properties is also supported by the vibrational properties. Thermomagnetization measurements at high temperature reveal a well-defined magnetic phase transition at high temperature (TC around 780 K due to induced ferromagnetic phase. Electron paramagnetic resonance (EPR studies reveal a good agreement between the EPR results and magnetic properties. The observed results are described on the basis of crystallite size variation, defect density, large strain, oxidation/reduction of Ni and interaction between uncompensated surfaces and particle core with lattice expansion. The obtained results suggest that nanoscale NiO powders with high TC and moderate magnetic moment at room temperature with cubic structure would be useful to expedite for spintronic devices.

De Rhetoribus de Suetônio

Directory of Open Access Journals (Sweden)

Artur Costrino

2014-12-01

Full Text Available O artigo visa apresentar ao leitor uma tradução inédita em português da vida dos rétores (que é parte da obra De Grammaticis et Rhetoribus de Suetônio. Como introdução, discute-se o lugar do gênero Vita em relação ao gênero Historia. Ainda há uma explanação sobre o “prefácio” da obra, o qual Suetônio divide em: história da declamação e praeexercitamina, de modo que o “prefácio”, então, não se enquadra no gênero Vita.

Paisagem e Património III

OpenAIRE

Cardoso, Isabel; Carapinha, Aurora; Rodrigues, Paulo; Matos, Rute; Santos, Ilda

2013-01-01

Com Paisagem e Património III (2013-2014) abordamos agora o Som, elemento frequentemente relegado para segundo plano, o que está em manifesta contradição com o impacto que tem na nossa apreciação da paisagem, mas também do património. Capacidade auditiva e sentido de equilíbrio são as duas funções do ouvido, que fazem dele um órgão do espaço tridimensional. A propagação relativamente lenta do som (330m p/ segundo) permite-nos uma avaliação bastante fiável da profundidade do espaço. Por sua ve...

Improvements of the versatile multiaperture negative ion source NIO1

Science.gov (United States)

Cavenago, M.; Serianni, G.; De Muri, M.; Veltri, P.; Antoni, V.; Baltador, C.; Barbisan, M.; Brombin, M.; Galatá, A.; Ippolito, N.; Kulevoy, T.; Pasqualotto, R.; Petrenko, S.; Pimazzoni, A.; Recchia, M.; Sartori, E.; Taccogna, F.; Variale, V.; Zaniol, B.; Barbato, P.; Baseggio, L.; Cervaro, V.; Fasolo, D.; Franchin, L.; Ghiraldelli, R.; Laterza, B.; Maniero, M.; Martini, D.; Migliorato, L.; Minarello, A.; Molon, F.; Moro, G.; Patton, T.; Ravarotto, D.; Rizzieri, R.; Rizzolo, A.; Sattin, M.; Stivanello, F.; Zucchetti, S.

2017-08-01

The ion source NIO1 (Negative Ion Optimization 1) was developed and installed as a reduced-size model of multi-aperture sources used in neutral beam injectors. NIO1 beam optics is optimized for a 135 mA H- current (subdivided in 9 beamlets) at a Vs = 60 kV extraction voltage, with an electron-to-ion current ratio Rj up to 2. Depending on gas pressure used, NIO1 was up to now operated with Vs qualitative agreement with theoretical and numerical models. A second bias voltage was tested for hydrogen. Beam footprints and a spectral emission sample are shown.

Analysis of cathode geometry to minimize cathode erosion in direct current microplasma jet

Energy Technology Data Exchange (ETDEWEB)

Causa, Federica [Dipartimento di Scienze dell' Ambiente, della Sicurezza, del Territorio, degli Alimenti e della Salute, Universita degli studi di Messina, 98122 Messina (Italy); Ghezzi, Francesco; Caniello, Roberto; Grosso, Giovanni [Istituto di Fisica del Plasma, Consiglio Nazionale delle Ricerche, EURATOM-ENEA-CNR Association, Via R. Cozzi 53, 20125 Milano (Italy); Dellasega, David [Istituto di Fisica del Plasma, Consiglio Nazionale delle Ricerche, EURATOM-ENEA-CNR Association, Via R. Cozzi 53, 20125 Milano (Italy); Dipartimento di Energia, Politecnico di Milano, Via Ponzio 34/3, 20133 Milano (Italy)

2012-12-15

Microplasma jets are now widely used for deposition, etching, and materials processing. The present study focuses on the investigation of the influence of cathode geometry on deposition quality, for microplasma jet deposition systems in low vacuum. The interest here is understanding the influence of hydrogen on sputtering and/or evaporation of the electrodes. Samples obtained with two cathode geometries with tapered and rectangular cross-sections have been investigated experimentally by scanning electron microscopy and energy dispersion X-ray spectroscopy. Samples obtained with a tapered-geometry cathode present heavy contamination, demonstrating cathode erosion, while samples obtained with a rectangular-cross-section cathode are free from contamination. These experimental characteristics were explained by modelling results showing a larger radial component of the electric field at the cathode inner wall of the tapered cathode. As a result, ion acceleration is larger, explaining the observed cathode erosion in this case. Results from the present investigation also show that the ratio of radial to axial field components is larger for the rectangular geometry case, thus, qualitatively explaining the presence of micro-hollow cathode discharge over a wide range of currents observed in this case. In the light of the above findings, the rectangular cathode geometry is considered to be more effective to achieve cleaner deposition.

Room temperature ferromagnetism in Mn-doped NiO nanoparticles

Science.gov (United States)

Layek, Samar; Verma, H. C.

2016-01-01

Mn-doped NiO nanoparticles of the series Ni1-xMnxO (x=0.00, 0.02, 0.04 and 0.06) are successfully synthesized using a low temperature hydrothermal method. Samples up to 6% Mn-doping are single phase in nature as observed from powder x-ray diffraction (XRD) studies. Rietveld refinement of the XRD data shows that all the single phase samples crystallize in the NaCl like fcc structure with space group Fm-3m. Unit cell volume decreases with increasing Mn-doping. Pure NiO nanoparticles show weak ferromagnetism, may be due to nanosize nature. Introduction of Mn within NiO lattice improves the magnetic properties significantly. Room temperature ferromagnetism is found in all the doped samples whereas the magnetization is highest for 2% Mn-doping and then decreases with further doping. The ZFC and FC branches in the temperature dependent magnetization separate well above 350 K indicating transition temperature well above room temperature for 2% Mn-doped NiO Nanoparticle. The ferromagnetic Curie temperature is found to be 653 K for the same sample as measured by temperature dependent magnetization study using vibrating sample magnetometer (VSM) in high vacuum.

Understanding the Intrinsic Electrochemistry of Ni-Rich Layered Cathodes

Science.gov (United States)

Sallis, Shawn

The demand for energy is continually increasing overtime and the key to meeting future demand in a sustainable way is with energy storage. Li-ion batteries employing layered transition metal oxide cathodes are one of the most technologically important energy storage technologies. However, current Li-ion batteries are unable to access their full theoretical capacity and suffer from performance limiting degradation over time partially originating from the cathode and partially from the interface with the electrolyte. Understanding the fundamental limitations of layered transition metal oxide cathodes requires a complete understanding of the surface and bulk of the materials in their most delithiated state. In this thesis, we employ LiNi0.8Co0.15Al 0.05O2 (NCA) as a model system for Ni-rich layered oxide cathodes. Unlike its parent compound, LiCoO2, NCA is capable of high states of delithiation with minimal structural transitions. Furthermore, commercially available NCA has little to no transition metals in the Li layer. X-ray spectroscopies are an ideal tool for studying cathodes at high states of delithiation due their elemental selectivity, range of probing depths, and sensitivity to both chemical and electronic state information. The oxidation state of the transition metals at the surface can be probed via X-ray photoelectron spectroscopy (XPS) while both bulk and surface oxidation states as well as changes in metal oxygen bonding can be probed using X-ray absorption spectroscopy (XAS). Using X-ray spectroscopy in tandem with electrochemical, transport and microscopy measurements of the same materials, the impedance growth with increasing delithiation was correlated with the formation of a disordered NiO phase on the surface of NCA which was precipitated by the release of oxygen. Furthermore, the surface degradation was strongly impacted by the type of Li salt used in the electrolyte, with the standard commercial salt LiPF6 suffering from exothermic decomposition

Solution-processed flexible NiO resistive random access memory device

Science.gov (United States)

Kim, Soo-Jung; Lee, Heon; Hong, Sung-Hoon

2018-04-01

Non-volatile memories (NVMs) using nanocrystals (NCs) as active materials can be applied to soft electronic devices requiring a low-temperature process because NCs do not require a heat treatment process for crystallization. In addition, memory devices can be implemented simply by using a patterning technique using a solution process. In this study, a flexible NiO ReRAM device was fabricated using a simple NC patterning method that controls the capillary force and dewetting of a NiO NC solution at low temperature. The switching behavior of a NiO NC based memory was clearly observed by conductive atomic force microscopy (c-AFM).

NiO and Fe/Mn in Fo-rich olivines from OIB, MORB, and mantle peridotites

Science.gov (United States)

Li, H.; Baker, M.; Hofmann, A. E.; Clague, D.; Stolper, E.

2006-12-01

Olivines from mantle peridotites have a narrow range of NiO (0.36±0.03 [1σ] wt%), but NiO of olivines in basalts suggest NiO in mantle olivines is actually more variable: e.g., Hawaiian phenocrysts (Fo>90) have NiO >0.55%, and olivines from continental flood basalts can have >0.5% NiO. At the other end of the spectrum, some basaltic suites (e.g., Iceland, MORBs) have Fo>90 olivines with NiO >0.2%. Partial melting calculations on peridotites show it is difficult to generate liquids that crystallize Fo>90 olivines with >0.4% NiO without resorting to complex processes. Hypotheses to explain the variability of NiO in mantle-derived olivines include (1) reaction of peridotite with silica-rich melts of eclogite results in decreasing modal abundance of olivine and increasing NiO in olivine [1,2]; (2) magmas with NiO-rich olivines come from sources enriched in NiO due to a core-derived component [3]. [4] proposed that high Fe/Mn of Hawaiian vs. Icelandic and MORB lavas reflect a core-derived component in their sources. Possible core incorporation is poorly constrained but FeO and NiO are expected to increase by such processes, leading to correlations between NiO and Fe/Mn in mantle rocks with significant core-derived components. We present high-precision analyses of Fo-rich olivines from OIBs, MORBs, komatiites, and mantle peridotites, focusing on NiO contents and Fe/Mn ratios. Our goal is to test hypotheses to explain elevated NiO of Fo-rich olivines in basalts. Olivines are Fo85.1-93.4; more were analyzed, but we focused on this range to avoid complications due to decreasing NiO in olivine with crystallization. Errors (1σ) are 0.01 wt% in NiO and 1.5 in Fe/Mn (wt). Our data show several features: (1) NiO contents and Fe/Mn ratios of Fo>88 olivines are positively correlated, with the low end of the trend (NiO ~0.23%, Fe/Mn ~61) defined by MORB and Iceland and the high end of the trend (NiO ~0.55%, Fe/Mn ~80) by Reunion and Hawaii. Between these end points, there is a

Depression cathode structure for cathode ray tubes having surface smoothness and method for producing same

International Nuclear Information System (INIS)

Rychlewski, T.V.

1984-01-01

Depression cathode structures for cathode ray tubes are produced by dispensing liquid cathode material into the depression of a metallic supporting substrate, removing excess cathode material by passing a doctor blade across the substrate surface and over the depression, and drying the cathode layer to a substantially immobile state. The cathode layer may optionally be further shaped prior to substantially complete drying thereof

Potentiometric Zinc Ion Sensor Based on Honeycomb-Like NiO Nanostructures

Directory of Open Access Journals (Sweden)

Magnus Willander

2012-11-01

Full Text Available In this study honeycomb-like NiO nanostructures were grown on nickel foam by a simple hydrothermal growth method. The NiO nanostructures were characterized by field emission electron microscopy (FESEM, high resolution transmission electron microscopy (HRTEM and X-ray diffraction (XRD techniques. The characterized NiO nanostructures were uniform, dense and polycrystalline in the crystal phase. In addition to this, the NiO nanostructures were used in the development of a zinc ion sensor electrode by functionalization with the highly selective zinc ion ionophore 12-crown-4. The developed zinc ion sensor electrode has shown a good linear potentiometric response for a wide range of zinc ion concentrations, ranging from 0.001 mM to 100 mM, with sensitivity of 36 mV/decade. The detection limit of the present zinc ion sensor was found to be 0.0005 mM and it also displays a fast response time of less than 10 s. The proposed zinc ion sensor electrode has also shown good reproducibility, repeatability, storage stability and selectivity. The zinc ion sensor based on the functionalized NiO nanostructures was also used as indicator electrode in potentiometric titrations and it has demonstrated an acceptable stoichiometric relationship for the determination of zinc ion in unknown samples. The NiO nanostructures-based zinc ion sensor has potential for analysing zinc ion in various industrial, clinical and other real samples.

Phase III Advanced Anodes and Cathodes Utilized in Energy Efficient Aluminum Production Cells; FINAL

International Nuclear Information System (INIS)

Christini, R.A.; Dawless, R.K.; Ray, S.P.; Weirauch, D.A. Jr.

2001-01-01

During Phase I of the present program, Alcoa developed a commercial cell concept that has been estimated to save 30% of the energy required for aluminum smelting. Phase ii involved the construction of a pilot facility and operation of two pilots. Phase iii of the Advanced Anodes and Cathodes Program was aimed at bench experiments to permit the resolution of certain questions to be followed by three pilot cells. All of the milestones related to materials, in particular metal purity, were attained with distinct improvements over work in previous phases of the program. NiO additions to the ceramic phase and Ag additions to the Cu metal phase of the cermet improved corrosion resistance sufficiently that the bench scale pencil anodes met the purity milestones. Some excellent metal purity results have been obtained with anodes of the following composition: Further improvements in anode material composition appear to be dependent on a better understanding of oxide solubilities in molten cryolite. For that reason, work was commissioned with an outside consultant to model the MeO - cryolite systems. That work has led to a better understanding of which oxides can be used to substitute into the NiO-Fe2O3 ceramic phase to stabilize the ferrites and reduce their solubility in molten cryolite. An extensive number of vertical plate bench electrolysis cells were run to try to find conditions where high current efficiencies could be attained. TiB2-G plates were very inconsistent and led to poor wetting and drainage. Pure TiB2 did produce good current efficiencies at small overlaps (shadowing) between the anodes and cathodes. This bench work with vertical plate anodes and cathodes reinforced the importance of good cathode wetting to attain high current efficiencies. Because of those conclusions, new wetting work was commissioned and became a major component of the research during the third year of Phase III. While significant progress was made in several areas, much work needs to be

A methodology for thermodynamic simulation of high temperature, internal reforming fuel cell systems

Science.gov (United States)

Matelli, José Alexandre; Bazzo, Edson

This work presents a methodology for simulation of fuel cells to be used in power production in small on-site power/cogeneration plants that use natural gas as fuel. The methodology contemplates thermodynamics and electrochemical aspects related to molten carbonate and solid oxide fuel cells (MCFC and SOFC, respectively). Internal steam reforming of the natural gas hydrocarbons is considered for hydrogen production. From inputs as cell potential, cell power, number of cell in the stack, ancillary systems power consumption, reformed natural gas composition and hydrogen utilization factor, the simulation gives the natural gas consumption, anode and cathode stream gases temperature and composition, and thermodynamic, electrochemical and practical efficiencies. Both energetic and exergetic methods are considered for performance analysis. The results obtained from natural gas reforming thermodynamics simulation show that the hydrogen production is maximum around 700 °C, for a steam/carbon ratio equal to 3. As shown in the literature, the found results indicate that the SOFC is more efficient than MCFC.

Nanosheet-assembled NiO microstructures for high-performance supercapacitors.

Science.gov (United States)

Purushothaman, Kamatchi Kamaraj; Babu, Inbamani Manohara; Sethuraman, Balasubramanian; Muralidharan, Gopalan

2013-11-13

Nanosheet-assembled NiO microstructures have been synthesized via a hydrothermal method. The presence of anionic surfactant in the fabrication process initiates the formation of lamellar micelles and a self-assembling process. This leads to the formation of NiO nanosheets and organizes it into microstructures. The effect of preparation temperature on the morphological, structural, and electrochemical properties and stability upon continuous charge/discharge cycles has been examined for supercapacitor applications. Electrochemical analysis demonstrated that NiO nanosheets prepared at 160 °C are capable of delivering a specific capacitance of 989 F g(-1) at a scan rate of 3 mV s(-1) for the potential window of 0-0.6 V. The nanosheets exhibit excellent capacity retention, 97% retention after 1000 continuous charge/discharge cycles, and an energy density of 49.45 W h kg(-1).

Oxygen bridges between NiO nanosheets and graphene for improvement of lithium storage.

Science.gov (United States)

Zhou, Guangmin; Wang, Da-Wei; Yin, Li-Chang; Li, Na; Li, Feng; Cheng, Hui-Ming

2012-04-24

Graphene has been widely used to dramatically improve the capacity, rate capability, and cycling performance of nearly any electrode material for batteries. However, the binding between graphene and these electrode materials has not been clearly elucidated. Here we report oxygen bridges between graphene with oxygen functional groups and NiO from analysis by X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, and Raman spectroscopy and confirm the conformation of oxygen bridges by the first-principles calculations. We found that NiO nanosheets (NiO NSs) are bonded strongly to graphene through oxygen bridges. The oxygen bridges mainly originate from the pinning of hydroxyl/epoxy groups from graphene on the Ni atoms of NiO NSs. The calculated adsorption energies (1.37 and 1.84 eV for graphene with hydroxyl and epoxy) of a Ni adatom on oxygenated graphene by binding with oxygen are comparable with that on graphene (1.26 eV). However, the calculated diffusion barriers of the Ni adatom on the oxygenated graphene surface (2.23 and 1.69 eV for graphene with hydroxyl and epoxy) are much larger than that on the graphene (0.19 eV). Therefore, the NiO NS is anchored strongly on the graphene through a C-O-Ni bridge, which allows a high reversible capacity and excellent rate performance. The easy binding/difficult dissociating characteristic of Ni adatoms on the oxygenated graphene facilitates fast electron hopping from graphene to NiO and thus the reversible lithiation and delithiation of NiO. We believe that the understanding of this oxygen bridge between graphene and NiO will lead to the development of other high-performance electrode materials.

Thermal behavior of La2O3/Nio composite prepared by sol-gel method

International Nuclear Information System (INIS)

Sakallioglu, M.

2005-01-01

The La 2 O 3 /NiO composite was prepared by sol-gel method by using transition metal oxides (La 2 O 3 /NiO). The variation of specific heat capacity Cp with temperature for La2O3/NiO composite was investigated by DSC. The heat capacity curve was taken with a heating rate of 20 degrees/min between 0-100 degrees. The variation of specific heat capacity was found by PKI Muse Standard Analysis Program. The thermal stability of the La 2 O 3 /NiO composite was investigated by thermogravimetric analysis (TG) in air atmosphere at a heating rate of 20 degrees/min. The weight loss of La 2 O 3 /NiO composite was determined by the variation of temperature

Investigation of the Enzyme activities of Alkaline Phosphatase, Lactate Dehydrogenase, Transaminase and Histopathological Changes of Liver after Exposure to NiO and NiO Nanoparticles in Rats

Directory of Open Access Journals (Sweden)

Aidin Marzban

2017-08-01

Conclusion: The results of this study demonstrate that exposure to different doses of NiONPs and NiO can induce different degrees of damage in a dose dependent manner. Thus, increasing level of liver enzymes and histopathological changes confirmed NiONPs and NiO toxicity.

Impact of the structural anisotropy of La2NiO4+δ on on high temperature surface modifications and diffusion of oxygen

International Nuclear Information System (INIS)

Gauquelin, Nicolas

2010-01-01

La 2 NiO 4+δ was first studied due to its structural similarities with the High Temperature superconductor La 2 NiO 4+δ and more recently due to its promise as a cathode material in Solid Oxide Fuel Cells as well as an oxygen exchange membrane. It crystallizes in the K 2 NiF 4 layered structure and accommodates highly mobile oxygen at its ground state and is therefore overstoichiometric. During this thesis, pure single crystals of La 2 NiO 4+δ were successfully grown using the floating-zone method, subsequently characterized using neutron and Laue Backscattering diffraction and oriented pieces of single crystal with [100] and [001] orientation were prepared. The surface morphology behavior after long term exposure to high temperature in different atmospheres was observed using microscopy techniques because stability at high temperature is required for application purposes and it was discovered a structural change to nickel-rich phases at T>1173 K. The sensibility of the oxygen non-stoichiometry to cooling was studied and subsequently a new 18 O- 18 O exchange apparatus allowing quenching of the samples using liquid nitrogen was developed. Oxygen selfdiffusion was studied using SIMS in the range 673-873K in both [100] and [001] crystallographic directions. The effect of the disorientation of the sample surface on the determination of the slowest diffusion coefficient was discovered and revealed the very strong anisotropy (>5 orders of magnitude difference) between the different diffusion paths. Finally using HTXRD and oxygen release experiments, it was shown that oxygen diffusion from interstitial oxygen starts to be relevant at 550-600 K and a change of behavior is observed around 700 K, corresponding to a possible change in the diffusion mechanism from interstitial to interstitialcy.

The Influence of NiO Addition in TiO2 Structure and Its Photoactivity

Science.gov (United States)

Wahyuningsih, S.; Ramelan, A. H.; Purwanti, P. D.; Munawaroh, H.; Ichsan, S.; Kristiawan, Y. R.

2018-03-01

The synthesis of TiO2 together with the TiO2-NiO composite using various annealing temperatures has been studied. The synthesis of TiO2 was performed by sol gel method using Titanium Tetra Isopropoxide (TTIP) precursor, whereas the synthesis of TiO2-NiO composite was done by wet impregnation method using NiNO3.6H2O precursor. This study aims to determine the influence of NiO addition in its structure and photoactivity. The diffraction of synthesized TiO2 at 400 °C temperature shows anatase TiO2 peak at 2θ = 25.35 °. The addition of NiO dopant to the synthesis of TiO2 process is carried out by annealing at 300 °C, 400 °C, 500 °C, 600 °C, and 700 °C, respectively. The TiO2-NiO composite has been prepared and shows the diffraction peak of NiO at 2θ=43° about 33.08 to 36.68%. The optimum result of Rhodamine B photodegradation with TiO2 was 43.15%, while the optimum result of Rhodamine B degradation with TiO2-NiO composite was 92.85%.

Metal oxides modified NiO catalysts for oxidative dehydrogenation of ethane to ethylene

KAUST Repository

Zhu, Haibo

2014-06-01

The sol-gel method was applied to the synthesis of Zr, Ti, Mo, W, and V modified NiO based catalysts for the ethane oxidative dehydrogenation reaction. The synthesized catalysts were characterized by XRD, N2 adsorption, SEM and TPR techniques. The results showed that the doping metals could be highly dispersed into NiO domains without the formation of large amount of other bulk metal oxide. The modified NiO materials have small particle size, larger surface area, and higher reduction temperature in contrast to pure NiO. The introduction of group IV, V and VI transition metals into NiO decreases the catalytic activity in ethane ODH. However, the ethylene selectivity is enhanced with the highest level for the Ni-W-O and Ni-Ti-O catalysts. As a result, these two catalysts show improved efficiency of ethylene production in the ethane ODH reaction. © 2014 Elsevier B.V. All rights reserved.

Bridging exchange bias effect in NiO and Ni(core)@NiO(shell) nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Rinaldi-Montes, Natalia, E-mail: nataliarin@gmail.com [Departamento de Física, Universidad de Oviedo, E-33007 Oviedo (Spain); Gorria, Pedro [Departamento de Física & IUTA, EPI, Universidad de Oviedo, E-33203 Gijón (Spain); Martínez-Blanco, David [Servicios Científico-Técnicos, Universidad de Oviedo, E-33006 Oviedo (Spain); Fuertes, Antonio B. [Instituto Nacional del Carbón, CSIC, E-33080 Oviedo (Spain); Fernández Barquín, Luis [CITIMAC, Facultad de Ciencias, Universidad de Cantabria, E-39005 Santander (Spain); Puente-Orench, Inés [Instituto de Ciencia de Materiales de Aragón, CSIC-Universidad de Zaragoza and Institut Laue-Langevin, BP 156, F-38042 Grenoble Cedex 9 (France); Blanco, Jesús A. [Departamento de Física, Universidad de Oviedo, E-33007 Oviedo (Spain)

2016-02-15

Among all bi-magnetic core(transition metal)@shell(transition metal oxide) nanoparticles (NPs), Ni@NiO ones show an onset temperature for the exchange bias (EB) effect far below the Néel temperature of bulk antiferromagnetic NiO. In this framework, the role played by the magnetism of NiO at the nanoscale is investigated by comparing the microstructure and magnetic properties of NiO and Ni@NiO NPs. With the aim of bridging the two systems, the diameter of the NiO NPs (~4 nm) is chosen to be comparable to the shell thickness of Ni@NiO ones (~2 nm). The EB effect in Ni@NiO NPs is attributed to the exchange coupling between the core and the shell, with an interfacial exchange energy of ΔE~0.06 erg cm{sup −2}, thus comparable to previous reports on Ni/NiO interfaces both in thin film and NP morphologies. In contrast, the EB detected in NiO NPs is explained in a picture where uncompensated spins located on a magnetically disordered surface shell are exchange coupled to the antiferromagnetic core. In all the studied NPs, the variation of the EB field as a function of temperature is described according to a negative exponential law with a similar decay constant, yielding a vanishing EB effect around T~40–50 K. In addition, the onset temperature for the EB effect in both NiO and Ni@NiO NPs seems to follow a universal dependence with the NiO crystallite size. - Highlights: • Comparison of the exchange bias effect in NiO and Ni(core)@NiO(shell) nanoparticles. • Universal temperature dependence of the exchange bias effect. • Suggested similar physical origin of the effect in both systems. • Size and crystallinity of the NiO shell hold the key for exchange bias properties.

DECLÍNIO EM PEQUENAS EMPRESAS: ABORDAGENS E TRABALHOS RELEVANTES

Directory of Open Access Journals (Sweden)

Luiz Antonio de Camargo Guerrazzi

Full Text Available RESUMO As pequenas empresas por seu relevante papel socioeconômico têm despertado crescente interesse da academia. Altas taxas de mortalidade associados às pequenas empresas têm sido objeto de pesquisas que investigam causas e fatores desencadeadores do declínio organizacional, fenômeno que antecede à morte da empresa. Neste artigo foi realizado um estudo bibliométrico em nove periódicos líderes na pesquisa em pequenas empresas, para obter uma visão geral e estrutural do conhecimento acumulado. Foi obtida uma amostra de 449 artigos relacionados ao declínio publicados entre 1989 e 2014. O método empregado permitiu a análise dos autores mais prolíficos, citações e obras com maior impacto, cocitações para entender a estrutura intelectual do campo e temas pesquisados para entender o foco da pesquisa. Foram empregadas técnicas de análise multivariada de dados como a análise fatorial exploratória e o escalonamento multidimensional (MDS. Foram identificados quatro principais temas pesquisados entrelaçando causas internas e externas como causadoras do declínio: empreendedorismo; administração estratégica e desempenho; inovação e evolução; liabilities (ameaças e ambiente. Este estudo indica que o declínio é desencadeado pela interação de causas internas e externas às empresas, fazendo um contraponto às pesquisas existentes que abordam ora umas ora outras e não estabelecem uma relação entre elas. Contribui para a academia com as bases sobre as quais novas pesquisas podem ser desenvolvidas e para a prática gerencial uma vez que identifica as causas do declínio e possibilita a tomada de decisões para neutralizá-las.

Highly improved sensibility and selectivity ethanol sensor of mesoporous Fe-doped NiO nanowires

Science.gov (United States)

Li, X. Q.; Wei, J. Q.; Xu, J. C.; Jin, H. X.; Jin, D. F.; Peng, X. L.; Hong, B.; Li, J.; Yang, Y. T.; Ge, H. L.; Wang, Xinqing

2017-12-01

In this paper, nickel oxides (NiO) and iron (Fe)-doped NiO nanowires (NWs) with the various doping content (from 1 to 9 at%) were synthesized by using SBA-15 templates with the nanocasting method. All samples were synthesized in the same conditions and exhibited the same mesoporous-structures, uniform diameter, and defects. Mesoporous-structures with high surface area created more active sites for the adsorption of oxygen on the surface of all samples, resulting in the smaller surface resistance in air. The impurity energy levels from the donor Fe-doping provided electrons to neutralize the holes of p-type Fe-doped NiO NWs, which greatly enhanced the total resistance. The comparative gas-sensing study between NiO NWs and Fe-doped NiO NWs indicated that the high-valence donor Fe-doping obviously improved the ethanol sensitivity and selectivity for Fe-doped NiO NWs. And Ni0.94Fe0.06O1.03 NWs sensor presented the highest sensitivity of 14.30 toward ethanol gas at 320 °C for the high-valence metal-doping.

Cathode materials review

Science.gov (United States)

Daniel, Claus; Mohanty, Debasish; Li, Jianlin; Wood, David L.

2014-06-01

The electrochemical potential of cathode materials defines the positive side of the terminal voltage of a battery. Traditionally, cathode materials are the energy-limiting or voltage-limiting electrode. One of the first electrochemical batteries, the voltaic pile invented by Alessandro Volta in 1800 (Phil. Trans. Roy. Soc. 90, 403-431) had a copper-zinc galvanic element with a terminal voltage of 0.76 V. Since then, the research community has increased capacity and voltage for primary (nonrechargeable) batteries and round-trip efficiency for secondary (rechargeable) batteries. Successful secondary batteries have been the lead-acid with a lead oxide cathode and a terminal voltage of 2.1 V and later the NiCd with a nickel(III) oxide-hydroxide cathode and a 1.2 V terminal voltage. The relatively low voltage of those aqueous systems and the low round-trip efficiency due to activation energies in the conversion reactions limited their use. In 1976, Wittingham (J. Electrochem. Soc., 123, 315) and Besenhard (J. Power Sources 1(3), 267) finally enabled highly reversible redox reactions by intercalation of lithium ions instead of by chemical conversion. In 1980, Goodenough and Mizushima (Mater. Res. Bull. 15, 783-789) demonstrated a high-energy and high-power LiCoO2 cathode, allowing for an increase of terminal voltage far beyond 3 V. Over the past four decades, the international research community has further developed cathode materials of many varieties. Current state-of-the-art cathodes demonstrate voltages beyond any known electrolyte stability window, bringing electrolyte research once again to the forefront of battery research.

Cathode materials review

International Nuclear Information System (INIS)

Daniel, Claus; Mohanty, Debasish; Li, Jianlin; Wood, David L.

2014-01-01

The electrochemical potential of cathode materials defines the positive side of the terminal voltage of a battery. Traditionally, cathode materials are the energy-limiting or voltage-limiting electrode. One of the first electrochemical batteries, the voltaic pile invented by Alessandro Volta in 1800 (Phil. Trans. Roy. Soc. 90, 403-431) had a copper-zinc galvanic element with a terminal voltage of 0.76 V. Since then, the research community has increased capacity and voltage for primary (nonrechargeable) batteries and round-trip efficiency for secondary (rechargeable) batteries. Successful secondary batteries have been the lead-acid with a lead oxide cathode and a terminal voltage of 2.1 V and later the NiCd with a nickel(III) oxide-hydroxide cathode and a 1.2 V terminal voltage. The relatively low voltage of those aqueous systems and the low round-trip efficiency due to activation energies in the conversion reactions limited their use. In 1976, Wittingham (J. Electrochem. Soc., 123, 315) and Besenhard (J. Power Sources 1(3), 267) finally enabled highly reversible redox reactions by intercalation of lithium ions instead of by chemical conversion. In 1980, Goodenough and Mizushima (Mater. Res. Bull. 15, 783-789) demonstrated a high-energy and high-power LiCoO 2 cathode, allowing for an increase of terminal voltage far beyond 3 V. Over the past four decades, the international research community has further developed cathode materials of many varieties. Current state-of-the-art cathodes demonstrate voltages beyond any known electrolyte stability window, bringing electrolyte research once again to the forefront of battery research

Cathode materials review

Energy Technology Data Exchange (ETDEWEB)

Daniel, Claus, E-mail: danielc@ornl.gov; Mohanty, Debasish, E-mail: danielc@ornl.gov; Li, Jianlin, E-mail: danielc@ornl.gov; Wood, David L., E-mail: danielc@ornl.gov [Oak Ridge National Laboratory, 1 Bethel Valley Road, MS6472 Oak Ridge, TN 37831-6472 (United States)

2014-06-16

The electrochemical potential of cathode materials defines the positive side of the terminal voltage of a battery. Traditionally, cathode materials are the energy-limiting or voltage-limiting electrode. One of the first electrochemical batteries, the voltaic pile invented by Alessandro Volta in 1800 (Phil. Trans. Roy. Soc. 90, 403-431) had a copper-zinc galvanic element with a terminal voltage of 0.76 V. Since then, the research community has increased capacity and voltage for primary (nonrechargeable) batteries and round-trip efficiency for secondary (rechargeable) batteries. Successful secondary batteries have been the lead-acid with a lead oxide cathode and a terminal voltage of 2.1 V and later the NiCd with a nickel(III) oxide-hydroxide cathode and a 1.2 V terminal voltage. The relatively low voltage of those aqueous systems and the low round-trip efficiency due to activation energies in the conversion reactions limited their use. In 1976, Wittingham (J. Electrochem. Soc., 123, 315) and Besenhard (J. Power Sources 1(3), 267) finally enabled highly reversible redox reactions by intercalation of lithium ions instead of by chemical conversion. In 1980, Goodenough and Mizushima (Mater. Res. Bull. 15, 783-789) demonstrated a high-energy and high-power LiCoO{sub 2} cathode, allowing for an increase of terminal voltage far beyond 3 V. Over the past four decades, the international research community has further developed cathode materials of many varieties. Current state-of-the-art cathodes demonstrate voltages beyond any known electrolyte stability window, bringing electrolyte research once again to the forefront of battery research.

Magnetization reversal dynamics in exchange-coupled NiO - Co bilayers

International Nuclear Information System (INIS)

Camarero, J.; Pennec, Y.; Bonfim, M.; Vogel, J.; Pizzini, S.; Fontaine, A.; Cartier, M.; Fettar, F.; Dieny, B.

2001-01-01

We performed a detailed study of the magnetization reversal in polycrystalline exchange-coupled NiO/Co bilayers over 10 decades of field sweep rate dH/dt for different NiO and Co thicknesses. For all sweep rates and thicknesses, the symmetry of the hysteresis loops shows that an identical pinning strength has to be overcome in both directions of the reversal. At low dH/dt the reversal is governed by domain wall displacement while domain nucleation is dominant at higher ones. The dH/dt at which the transition between the two regimes takes place depends on the relative thickness of the NiO and Co layers. It increases (decreases) when the Co (NiO) thickness is increased. Experimentally, it was found that the energy barrier varies linearly with the square root of the area corresponding to the activation (Barkhausen) volume which is consistent with a random walk model of the coupling between antiferromagnetic and ferromagnetic layers. The results can be explained in terms of a thermally activated switching of the NiO magnetization dragged by the Co reversal. [copyright] 2001 American Institute of Physics

Museologia e patrimônio: encontros e desencontros

Directory of Open Access Journals (Sweden)

Marcio Ferreira Rangel

Full Text Available Ao direcionarmos o olhar para as décadas de 1920 e 1930, podemos verificar os diferentes projetos, apresentados por parte da intelectualidade brasileira, para a área do patrimônio e dos museus. Esta assertiva poder ser confirmada por meio da análise dos diversos projetos e anteprojetos que buscavam normalizá-la. Nesse período, é posta em curso a ideia da construção de um Estado onde as elites têm papel de destaque no encaminhamento da questão política e cultural. Assim, são criados importantes instituições e órgãos, tais como o Museu Histórico Nacional (1922, o Curso de Museus (1932 e a Inspetoria de Monumentos Nacionais (1934. Tanto o Curso de Museus como a Inspetoria de Monumentos Nacionais são considerados marcos. O primeiro na institucionalização da Museologia e dos estudos de museus no Brasil. O segundo foi um dos principais antecedentes do Serviço do Patrimônio Histórico e Artístico Nacional (SPHAN, atual Instituto do Patrimônio Histórico e Artístico Nacional (IPHAN, criado em 1937. O presente artigo pretende lançar luzes nessa discussão ao analisar e problematizar o papel desempenhado por diferentes atores no processo de formação e configuração das áreas da Museologia e do Patrimônio, enfatizando as convergências e divergências existentes em suas trajetórias.

Hollow NiO nanofibers modified by citric acid and the performances as supercapacitor electrode

International Nuclear Information System (INIS)

Ren, Bo; Fan, Meiqing; Liu, Qi; Wang, Jun; Song, Dalei; Bai, Xuefeng

2013-01-01

Graphical abstract: The possible formation process of NiO nanofibers without citric acid (a), and modified by citric acid (b). When the nanofibers is modified by citric acid, the nickel citrate is produced by complexing action of citric acid and nickel nitrate. Because of the larger space steric hindrance, the structure is limited by the molecular geometry. Under high temperature, the hollow nanofibers composed of NiO slices formed after the removal of PVP. Highlights: ► The method of obtaining hollow nanofibers is raised for the first time. ► The prepared NiO nanofibers are hollow tube and comprised of many NiO sheets. ► The hollow structure facilitated the electrolyte penetration. ► The hollow NiO nanofibers have good electrochemical properties. -- Abstract: NiO nanofibers modified by citric acid (NiO/CA) for supercapacitor material have been fabricated by electrospinning process. The characterizations of the nanofibers are investigated by Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Electrochemical properties are characterized by cyclic voltammetry, galvanostatic charge/discharge measurements, and electrochemical impedance spectroscopy. Results show that the NiO/CA nanofibers are hollow tube and comprised of many NiO sheets. Furthermore, the NiO/CA nanofibers have good electrochemical reversibility and display superior capacitive performance with large capacitance (336 F g −1 ), which is 2.5 times of NiO electrodes. Moreover, the NiO/CA nanofibers show excellent cyclic performance after 1000 cycles

The influence of cathode excavation of cathodic arc evaporator on thickness uniformity and erosion products angle distribution

Directory of Open Access Journals (Sweden)

D. V. Duhopel'nikov

2014-01-01

Full Text Available Cathodic arc evaporators are used for coating with functional films. Prolonged or buttend evaporators may be used for this purposes. In butt-end evaporator the cathode spots move continuously on the cathode work surface and evaporate cathode material. High depth excavation profile forms on the cathode work surface while the thick coating precipitation (tens or hundreds of microns. The cathode excavation profile is shaped like a “cup” with high walls for electrostatic discharge stabilization systems with axial magnetic fields. Cathode spots move on the bottom of the “cup”. It is very likely that high “cup” walls are formed as a result of lasting work time influence on the uniformity of precipitated films.In the present work the influence of excavation profile walls height on the uniformity of precipitated coating was carried out. The high profile walls are formed due to lasting work of DC vacuum arc evaporator. The cathode material used for tests was 3003 aluminum alloy. The extended substrate was placed parallel to the cathode work surface. Thickness distribution along the substrate length with the new cathode was obtained after 6 hours and after 12 hours of continuous operation.The thickness distribution of precipitated coating showed that the cathode excavation has an influence on the angular distribution of the matter escaping the cathode. It can be clearly seen from the normalized dependence coating thickness vs the distance from the substrate center. Also the angular distribution of the matter flow from the cathode depending on the cathode working time was obtained. It was shown that matter flow from the cathode differs from the LambertKnudsen law. The more the cathode excavation the more this difference.So, cathode excavation profile has an influence on the uniformity of precipitated coating and it is necessary to take in account the cathode excavation profile while coating the thick films.

Influence of O2 plasma treatment on NiO x layer in perovskite solar cells

Science.gov (United States)

Nishihara, Yoshihiko; Chikamatsu, Masayuki; Kazaoui, Said; Miyadera, Tetsuhiko; Yoshida, Yuji

2018-04-01

We fabricated perovskite solar cells (PSCs) with an inverted p-i-n planar structure using a NiO x film as a hole-transporting layer. Since the surface of the NiO x film fabricated by sputtering is hydrophobic, O2 plasma treatment under various conditions was performed to improve its wettability. Water contact angles after the treatment under both normal and weak conditions on the NiO x film reached approximately 15°. After the treatment, the valence band level of the NiO x film was deeper by about 0.15 eV. The maximum efficiency of the NiO x -based device under the optimized O2 plasma condition reached 12.3%.

Ferromagnetic Behaviors in Fe-Doped NiO Nanofibers Synthesized by Electrospinning Method

Directory of Open Access Journals (Sweden)

Yi-Dong Luo

2013-01-01

Full Text Available Ni1−xFexO nanofibers with different Fe doping concentration have been synthesized by electrospinning method. An analysis of the phase composition and microstructure shows that Fe doping has no influence on the crystal structure and morphology of NiO nanofibers, which reveals that the doped Fe ions have been incorporated into the NiO host lattice. Pure NiO without Fe doping is antiferromagnetic, yet all the Fe-doped NiO nanofiber samples show obvious room-temperature ferromagnetic properties. The saturation magnetization of the nanofibers can be enhanced with increasing Fe doping concentration, which can be ascribed to the double exchange mechanism through the doped Fe ions and free charge carriers. In addition, it was found that the diameter of nanofibers has significant impact on the ferromagnetic properties, which was discussed in detail.

Nanostructured sulfur cathodes

KAUST Repository

Yang, Yuan

2013-01-01

Rechargeable Li/S batteries have attracted significant attention lately due to their high specific energy and low cost. They are promising candidates for applications, including portable electronics, electric vehicles and grid-level energy storage. However, poor cycle life and low power capability are major technical obstacles. Various nanostructured sulfur cathodes have been developed to address these issues, as they provide greater resistance to pulverization, faster reaction kinetics and better trapping of soluble polysulfides. In this review, recent developments on nanostructured sulfur cathodes and mechanisms behind their operation are presented and discussed. Moreover, progress on novel characterization of sulfur cathodes is also summarized, as it has deepened the understanding of sulfur cathodes and will guide further rational design of sulfur electrodes. © 2013 The Royal Society of Chemistry.

Effect of substrate temperature and oxygen partial pressure on RF sputtered NiO thin films

Science.gov (United States)

Cheemadan, Saheer; Santhosh Kumar, M. C.

2018-04-01

Nickel oxide (NiO) thin films were deposited by RF sputtering process and the physical properties were investigated for varying substrate temperatures and oxygen partial pressure. The variation of the crystallographic orientation and microstructure of the NiO thin films with an increase in substrate temperature were studied. It was observed that NiO thin films deposited at 350 °C shows relatively good crystalline characteristics with a preferential orientation along (111) plane. With the optimum substrate temperature of 350 °C, the NiO thin films were deposited under various oxygen partial pressures at the same experimental conditions. The structural, optical and electrical properties of NiO thin films under varying oxygen partial pressure of 10%–50% were investigated. From XRD it is clear that the films prepared in the pure argon atmosphere were amorphous while the films in oxygen partial pressure exhibited polycrystalline NiO phase. SEM and AFM investigations unveil that the higher substrate temperature improves the microstructure of the thin films. It is revealed that the NiO thin films deposited at oxygen partial pressure of 40% and a substrate temperature of 350 °C, showed higher electrical conductivity with p-type characteristics.

Facile synthesis and electron transport properties of NiO nanostructures investigated by scanning tunneling microscopy

Directory of Open Access Journals (Sweden)

Govind Mallick

2017-08-01

Full Text Available Due to their unique chemical, thermal, electronic and photonic properties, low -dimensional transition metal oxides, especially NiO, have attracted great deal of attention for potential applications in a wide range of technologies, such as, sensors, electrochromic coatings and self-healing materials. However, their synthesis involves multi-step complex procedures that in addition to being expensive, further introduce impurities. Here we present a low cost facile approach to synthesize uniform size NiO nanoparticles (NPs from hydrothermally grown Ni(OH2. Detailed transmission electron microscopic analysis reveal the average size of NiO NPs to be around 29 nm. The dimension of NiO NP is also corroborated by the small area scanning tunneling microscope (STM measurements. Further, we investigate electron transport characteristics of newly synthesized Ni(OH2 and NiO nanoparticles on p-type Si substrate using scanning tunneling microscopy. The conductivity of Ni(OH2 and NiO are determined to be 1.46x10-3 S/cm and 2.37x10-5 S/cm, respectively. The NiO NPs exhibit a lower voltage window (∼0.7 V electron tunneling than the parent Ni(OH2.

Arcjet cathode phenomena

Science.gov (United States)

Curran, Francis M.; Haag, Thomas W.; Raquet, John F.

1989-01-01

Cathode tips made from a number of different materials were tested in a modular arcjet thruster in order to examine cathode phenomena. Periodic disassembly and examination, along with the data collected during testing, indicated that all of the tungsten-based materials behaved similarly despite the fact that in one of these samples the percentage of thorium oxide was doubled and another was 25 percent rhenium. The mass loss rate from a 2 percent thoriated rhenium cathode was found to be an order of magnitude greater than that observed using 2 percent thoriated tungsten. Detailed analysis of one of these cathode tips showed that the molten crater contained pure tungsten to a depth of about 150 microns. Problems with thermal stress cracking were encountered in the testing of a hafnium carbide tip. Post test analysis showed that the active area of the tip had chemically reacted with the propellant. A 100 hour continuous test was run at about 1 kW. Post test analysis revealed no dendrite formation, such as observed in a 30 kW arcjet lifetest, near the cathode crater. The cathodes from both this test and a previously run 1000 hour cycled test displayed nearly identical arc craters. Data and calculations indicate that the mass losses observed in testing can be explained by evaporation.

Temperature dependence of the magnetization of disc shaped NiO nanoparticles

DEFF Research Database (Denmark)

Klausen, Stine Nyborg; Lindgard, P.A.; Lefmann, Kim

2002-01-01

as a temperature dependent contribution of a structural peak in contrast to bulk NiO. The two magnetic signals vanish at the same temperature. The data are interpreted on the basis of an extended mean field model on disc shaped NiO particles. This model includes the finite size dependence of the effective field...

Sensitive Nonenzymatic Electrochemical Glucose Detection Based on Hollow Porous NiO

Science.gov (United States)

He, Gege; Tian, Liangliang; Cai, Yanhua; Wu, Shenping; Su, Yongyao; Yan, Hengqing; Pu, Wanrong; Zhang, Jinkun; Li, Lu

2018-01-01

Transition metal oxides (TMOs) have attracted extensive research attentions as promising electrocatalytic materials. Despite low cost and high stability, the electrocatalytic activity of TMOs still cannot satisfy the requirements of applications. Inspired by kinetics, the design of hollow porous structure is considered as a promising strategy to achieve superior electrocatalytic performance. In this work, cubic NiO hollow porous architecture (NiO HPA) was constructed through coordinating etching and precipitating (CEP) principle followed by post calcination. Being employed to detect glucose, NiO HPA electrode exhibits outstanding electrocatalytic activity in terms of high sensitivity (1323 μA mM-1 cm-2) and low detection limit (0.32 μM). The excellent electrocatalytic activity can be ascribed to large specific surface area (SSA), ordered diffusion channels, and accelerated electron transfer rate derived from the unique hollow porous features. The results demonstrate that the NiO HPA could have practical applications in the design of nonenzymatic glucose sensors. The construction of hollow porous architecture provides an effective nanoengineering strategy for high-performance electrocatalysts.

Coral-like CeO{sub 2}/NiO nanocomposites with efficient enzyme-mimetic activity for biosensing application

Energy Technology Data Exchange (ETDEWEB)

Mu, Jianshuai; Zhao, Xin; Li, Jie [College of Chemistry, Key Laboratory of Inorganic-Organic Hybrid Functional Material Chemistry, Ministry of Education, Tianjin Key Laboratory of Structure and Performance for Functional Molecules, Tianjin Normal University, Tianjin 300387 (China); Yang, En-Cui, E-mail: encui_yang@163.com [College of Chemistry, Key Laboratory of Inorganic-Organic Hybrid Functional Material Chemistry, Ministry of Education, Tianjin Key Laboratory of Structure and Performance for Functional Molecules, Tianjin Normal University, Tianjin 300387 (China); Zhao, Xiao-Jun, E-mail: xiaojun_zhao15@163.com [College of Chemistry, Key Laboratory of Inorganic-Organic Hybrid Functional Material Chemistry, Ministry of Education, Tianjin Key Laboratory of Structure and Performance for Functional Molecules, Tianjin Normal University, Tianjin 300387 (China); Collaborative Innovation Center of Chemical Science and Engineering, Tianjin 300071 (China)

2017-05-01

Development of nanomaterials-based enzymatic mimics has gained considerable attention in recent years, because of their low cost, high stability and efficiently catalytic ability. Here, CeO{sub 2} was successfully incorporated into the coral-like NiO nanostructures assembled by nanoflakes with high surface area, forming the coral-like CeO{sub 2}/NiO nanocomposites. The morphology and composition of CeO{sub 2}/NiO nanocomposites were characterized by XRD, SEM, element mapping and XPS. The results of characterization showed that cerium was highly dispersed in the coral-like NiO nanostructures. The peroxidase-like activity of CeO{sub 2}/NiO nanocomposites was investigated, and they exhibited enhanced peroxidase-like activity in comparison to that of pure NiO or CeO{sub 2}. The catalytic activity was dependent on the cerium content, and the optimal content was 2.5%. The enhanced catalytic activity of CeO{sub 2}/NiO nanocomposites arised from their high ability of electron transfer because of cerium incorporation. The catalytic performance of CeO{sub 2}/NiO nanocomposites was evaluated by steady-state kinetic, which showed that the CeO{sub 2}/NiO nanocomposites exhibited higher affinity for the substrates and similar catalytic efficiency compared with natural peroxidase. Based on the efficient peroxidase-like activity, CeO{sub 2}/NiO was used for H{sub 2}O{sub 2} determination. The constructed colorimetric H{sub 2}O{sub 2} sensor had fast response for only 5 min, a wide linear range from 0.05 to 40 mM and a low detection limit with 0.88 μM. The CeO{sub 2}/NiO nanocomposites were expected to have potential applications in clinical diagnosis and biotechnology as enzymatic mimics. - Highlights: • Coral-like CeO{sub 2}/NiO nanocomposites with different Ce content were synthesized. • CeO{sub 2} was highly dispersed in the NiO matrixes with high surface area. • CeO{sub 2}/NiO nanocomposites exhibited efficient peroxidase-like activity. • A colorimetric H{sub 2}O

Synthesis, Characterization, and Magnetic Properties of Pure and EDTA-Capped NiO Nanosized Particles

Directory of Open Access Journals (Sweden)

H. T. Rahal

2017-01-01

Full Text Available The effect of ethylenediaminetetraacetic acid (EDTA as a capping agent on the structure, morphology, optical, and magnetic properties of nickel oxide (NiO nanosized particles, synthesized by coprecipitation method, was investigated. Nickel chloride hexahydrate and sodium hydroxide (NaOH were used as precursors. The resultant nanoparticles were characterized by X-ray diffraction (XRD, transmission electron microscopy (TEM, and scanning electron microscopy (SEM. XRD patterns showed that NiO have a face-centered cubic (FCC structure. The crystallite size, estimated by Scherrer formula, has been found in the range of 28–33 nm. It is noticed that EDTA-capped NiO nanoparticles have a smaller size than pure nanoparticles. Thus, the addition of 0.1 M capping agent EDTA can form a nucleation point for nanoparticles growth. The optical and magnetic properties were investigated by Fourier transform infrared spectroscopy (FTIR and UV-vis absorption spectroscopy (UV as well as electron paramagnetic resonance (EPR and magnetization measurements. FTIR spectra indicated the presence of absorption bands in the range of 402–425 cm−1, which is a common feature of NiO. EPR for NiO nanosized particles was measured at room temperature. An EPR line with g factor ≈1.9–2 is detected for NiO nanoparticles, corresponding to Ni2+ ions. The magnetic hysteresis of NiO nanoparticles showed that EDTA capping recovers the surface magnetization of the nanoparticles.

NANOCOLORAÇÃO DE LIGAS DE ALUMÍNIO

OpenAIRE

GUILHERME JOSÉ TURCATEL ALVES

2012-01-01

A utilização do alumínio torna-se cada vez maior, devido à leveza do metal e sua elevada resistência a corrosão. A anodização do alumínio é uma técnica bem conhecida e está sendo muito utilizada para o aumento da durabilidade do metal. Esta técnica força eletroquimicamente o crescimento da camada de óxido. A camada anodizada tem a peculiaridade de possuir nanotubos o que permite a inserção de pigmentos e outros compostos no interior destes. O processo de anodização, utilizado industrialmente ...

High temperature growth kinetics and texture of surface-oxidised NiO for coated superconductor applications

Energy Technology Data Exchange (ETDEWEB)

Kursumovic, A; Tomov, R; Huehne, R; Glowacki, B A; Everts, J E; Tuissi, A; Villa, E; Holzapfel, B

2003-03-15

Thick NiO films were grown in air, on biaxially textured (0 0 1) Ni and as-rolled Ni tapes, at temperatures from 1050 to 1350 deg. C. Ni diffusion through the NiO film mainly contributes to the growth since is much faster than oxygen diffusion and occurs by a vacancy diffusion mechanism in the lattice at high temperatures. Parabolic growth kinetics were found for both NiO film thickness and grain growth, and compared with the literature data. Competitive growth of (1 1 1) and (0 0 1) oriented grains establishes the final NiO orientation at temperatures below 1250 deg. C, while at higher temperatures leakage diffusion at/towards grain boundaries, grain coarsening and (1 1 0) oriented grains disrupt the (1 0 0) texture. Hence, development of epitaxy of NiO on textured Ni tapes was found to be largely due to growth kinetics depending on both, time and temperature. We report here a systematic study of the microstructure and kinetics of formation of textured NiO substrate for application as a buffer layer in coated conductor technology.

Solution growth of NiO nanosheets supported on Ni foam as high-performance electrodes for supercapacitors

Science.gov (United States)

Yan, Hailong; Zhang, Deyang; Xu, Jinyou; Lu, Yang; Liu, Yunxin; Qiu, Kangwen; Zhang, Yihe; Luo, Yongsong

2014-08-01

Well-aligned nickel oxide (NiO) nanosheets with the thickness of a few nanometers supported on a flexible substrate (Ni foam) have been fabricated by a hydrothermal approach together with a post-annealing treatment. The three-dimensional NiO nanosheets were further used as electrode materials to fabricate supercapacitors, with high specific capacitance of 943.5, 791.2, 613.5, 480, and 457.5 F g-1 at current densities of 5, 10, 15, 20, and 25 A g-1, respectively. The NiO nanosheets combined well with the substrate. When the electrode material was bended, it can still retain 91.1% of the initial capacitance after 1,200 charging/discharging cycles. Compared with Co3O4 and NiO nanostructures, the specific capacitance of NiO nanosheets is much better. These characteristics suggest that NiO nanosheet electrodes are promising for energy storage application with high power demands.

Solution growth of NiO nanosheets supported on Ni foam as high-performance electrodes for supercapacitors.

Science.gov (United States)

Yan, Hailong; Zhang, Deyang; Xu, Jinyou; Lu, Yang; Liu, Yunxin; Qiu, Kangwen; Zhang, Yihe; Luo, Yongsong

2014-01-01

Well-aligned nickel oxide (NiO) nanosheets with the thickness of a few nanometers supported on a flexible substrate (Ni foam) have been fabricated by a hydrothermal approach together with a post-annealing treatment. The three-dimensional NiO nanosheets were further used as electrode materials to fabricate supercapacitors, with high specific capacitance of 943.5, 791.2, 613.5, 480, and 457.5 F g(-1) at current densities of 5, 10, 15, 20, and 25 A g(-1), respectively. The NiO nanosheets combined well with the substrate. When the electrode material was bended, it can still retain 91.1% of the initial capacitance after 1,200 charging/discharging cycles. Compared with Co3O4 and NiO nanostructures, the specific capacitance of NiO nanosheets is much better. These characteristics suggest that NiO nanosheet electrodes are promising for energy storage application with high power demands.

Role of copper/vanadium on the optoelectronic properties of reactive RF magnetron sputtered NiO thin films

Science.gov (United States)

Panneerselvam, Vengatesh; Chinnakutti, Karthik Kumar; Thankaraj Salammal, Shyju; Soman, Ajith Kumar; Parasuraman, Kuppusami; Vishwakarma, Vinita; Kanagasabai, Viswanathan

2018-04-01

In this study, pristine nickel oxide (NiO), copper-doped NiO (Cu-NiO) and vanadium-doped NiO (V-NiO) thin films were deposited using reactive RF magnetron co-sputtering as a function of dopant sputtering power. Cu (0-8 at%) and V (0-1 at%) were doped into the NiO lattice by varying the sputtering power of Cu and V in the range of 5-15 W. The effect of dopant concentration on optoelectronic behavior is investigated by UV-Vis-NIR spectrophotometer and Hall measurements. XRD analysis showed that the preferred orientation of the cubic phase for undoped NiO changes from (200) to (111) plane when the sputtering parameters are varied. The observed changes in the lattice parameters and bonding states of the doped NiO indicate the substitution of Ni ions by monovalent Cu and trivalent V ions. The optical bandgap of pristine NiO, Cu-NiO, and V-NiO was found to be 3.6, 3.45, and 3.05 eV, respectively, with decreased transmittance and resistivity. Further analysis using SEM and AFM described the morphological behavior of doped NiO thin films and Raman spectroscopy indicated the structural changes on doping. These findings would be helpful in fabricating solid-state solar cells using doped NiO as efficient hole transporting material.

Casas e portas da memória e do patrimônio

Directory of Open Access Journals (Sweden)

Mario Chagas

2007-12-01

Full Text Available Apresenta reflexões em torno do conceito de patrimônio, desde a sua origem até a contemporaneidade. Afirma que existe uma relação intrínseca entre patrimônio e poder, que permanece na relação entre patrimônio e propriedade, seja material ou espiritual, econômica ou simbólica e a sua vinculação à idéia de preservação. Destaca que a noção de posse parece ser mais adequada aos museus do que a de propriedade Sugere que o caráter preservacionista e o sentido de posse estão na raiz da instituição do patrimônio e do museu (casa de memória e poder. Ressalta que a preservação como prática social que é utilizada para a construção de determinadas narrativas tem um caráter subjetivo, que é mascarado por discursos que se pretendem positivos, científicos e objetivos. Conclui que o que está em jogo nos museus e também no domínio do patrimônio cultural é memória, esquecimento, resistência e poder, perigo e valor, múltiplos significados e funções, silêncio e fala, destruição e preservação. E por tudo isso interessa compreendê-los em sua dinâmica social e interessa compreender o que se pode fazer com eles, contra eles, apesar e a partir deles.

Osteologia do neurocrânio de Iguana iguana iguana (Squamata: Iguanidae

Directory of Open Access Journals (Sweden)

Fabiano C. Lima

2014-12-01

Full Text Available Resumo: O crânio representa o segmento com conspícuas adaptações que, nos lagartos, podem ser conservativas ou impulsionadas por pressões seletivas. Objetivando subsidiar o conhecimento morfológico dos répteis, fornecemos uma descrição detalhada dos ossos que formam o neurocrânio de Iguana iguana iguana com base na análise de três esqueletos secos de espécimes adultos. O crânio da referia espécie possui características basais entre os lagartos sem o fechamento das aberturas cranianas e formato geral triangular. As estruturas ósseas que formam a base craniana apresentam muitas fusões, principalmente no assoalho. Na face caudal o exoccipital e o opistótico estão fundidos e formam o otoccipital, que contribui para a formação dos terços laterais do côndilo occipital. A parte central do côndilo é formada pelo supraoccipital. Fusões e estruturas esqueléticas presentes em Iguana são similares aos demais lagartos. Não foram descritas autapomorfias no neurocrânio para esta espécie.

Aspectos do Gerenciamento do Patrimônio Arqueológico no Brasil

Directory of Open Access Journals (Sweden)

Alexandre Henrique Delforge

2013-12-01

Full Text Available Apresenta-se uma visão daquilo que se constitui no Gerenciamento do Patrimônio Arqueológico (GPA dentro do universo do Gerenciamento do Patrimônio Cultural. O GPA possui características globais, ligadas à ciência da Arqueologia, à Conservação e à Museologia; e locais determinadas pela legislação, desenvolvimento econômico e cultura de cada país e região. É proposta uma visão sistêmica do GPA que atende a ciência, à legislação nacional, ao desenvolvimento econômico, à preservação do patrimônio cultural e à promoção do meio ambiente sócio econômico (cultural. Os agentes sobre este patrimônio são classificados em três grupos (Científico, Estatal e Social com base em critérios da legislação nacional, em dados de campo da atuação no gerenciamento e informações sobre o desenvolvimento econômico específico do Estado de Minas Gerais. Apresentase ao final um diagnóstico cartográfico do patrimônio arqueológico no Estado em sua ligação com os três grupos de agentes e com o desenvolvimento econômico.

Hydrothermal synthesis and electrochemical performance of NiO microspheres with different nanoscale building blocks

International Nuclear Information System (INIS)

Wang Ling; Hao Yanjing; Zhao Yan; Lai Qiongyu; Xu Xiaoyun

2010-01-01

NiO microspheres were successfully obtained by calcining the Ni(OH) 2 precursor, which were synthesized via the hydrothermal reaction of nickel chloride, glucose and ammonia. The products were characterized by TGA, XRD and SEM. The influences of glucose and reaction temperature on the morphologies of NiO samples were investigated. Moreover, the possible growth mechanism for the spherical morphology was proposed. The charge/discharge test showed that the as-prepared NiO microspheres composed of nanoparticles can serve as an ideal electrode material for supercapacitor due to the spherical hollow structure. -- Graphical Abstract: Fig. 5 is the SEM image of NiO that was prepared in the different hydrothermal reaction temperatures. It showed that reaction temperature played a crucial role for the morphology of products.

Direct synthesis of porous NiO nanowall arrays on conductive substrates for supercapacitor application

International Nuclear Information System (INIS)

Zhu, Jianhui; Jiang, Jian; Liu, Jingping; Ding, Ruimin; Ding, Hao; Feng, Yamin; Wei, Guangming; Huang, Xintang

2011-01-01

Porous NiO nanowall arrays (NWAs) grown on flexible Fe-Co-Ni alloy have been successfully synthesized by using nullaginite (Ni 2 (OH) 2 CO 3 ) as precursor and investigated as supercapacitor electrodes. In details, we adopted a simple hydrothermal method to realize Ni 2 (OH) 2 CO 3 NWAs and examined their robust mechanical adhesion to substrate via a long-time ultrasonication test. Porous NiO NWAs were then obtained by a post-calcination towards precursors at 500 o C in nitrogen atmosphere. Electrochemical properties of as-synthesized NiO NWAs were evaluated by cyclic voltammetry and galvanostatic charge/discharge; porous NiO NWAs electrode delivered a specific capacitance of 270 F/g (0.67 A/g); even at high current densities, the electrode could still deliver a high capacitance up to 236 F/g (13.35 A/g). Meanwhile, it exhibited excellent cycle lifetime with ∼93% specific capacitance kept after 4000 cycles. These results suggest that as-made porous NiO NWAs electrode is a promising candidate for future thin-film supercapacitors and other microelectronic systems. -- Graphical abstract: Porous NiO nanowall arrays (NWAs) grown on alloy substrate have been made using nullaginite as precursor and studied as supercapacitor electrodes. Porous nanowalls interconnected with each other resulting in the formation of extended-network architectures and exhibited excellent capacitor properties. NiO NWAs electrode delivered a capacitance of 270 F/g (0.67 A/g); even at high current density, the electrode could still deliver a high capacitance up to 236 F/g (13.35 A/g). Besides, it exhibited excellent cycle lifetime with ∼93% capacitance kept after 4000 cycles. These remarkable results made it possible for mass production of NiO NWAs and future thin-film microelectronic applications. Display Omitted Research highlights: → Large-scale nullaginite (Ni 2 (OH) 2 CO 3 ) nanowall arrays (NWAs) have been synthesized on flexible alloy substrate by a facile hydrothermal method. �

O RACIOCÍNIO ESPACIAL NA ERA DAS TECNOLOGIAS INFORMACIONAIS

Directory of Open Access Journals (Sweden)

Valdenildo Pedro da Silva

2007-12-01

Full Text Available No mundo contemporâneo, ou, mais precisamente, nesta era da informação instantânea e simultânea, o raciocínio geográfico tem se destacado e, simultaneamente, se alterado por meio de novos aspectos sociais e tecnológicos. O presente estudo foi realizado com dezenove docentes atuantes em vários cursos de formação de professor de geografia de instituições públicas e privadas de diversas regiões do Brasil. Esses docentes têm utilizado as novas tecnologias e/ou pesquisado e produzido trabalhos a respeito delas no ensino de geografia. Diante disso, perseguimos o estudo na busca de se responder a seguinte indagação: novas tecnologias e raciocínio espacial: mas o que isso tem a ver? As tecnologias atuais, como veículos de informações, não têm a finalidade de desenvolver o “saber pensar o espaço” ou de realizar o “raciocínio espacial”, mas mesmo sem essa finalidade as pessoas aprendem geografia, pensam com a mediação dessas tecnologias. O ensino de geografia contribuiu para a formação de diversas pessoas por meio do desenvolvimento do raciocínio espacial realizado em duas diferentes escalas, do local ao global, mostrando articulações entre os diversos níveis de abstração, desde o espaço do trabalho até sua inserção em uma sociedade que se internacionaliza de maneira acelerada.

Grafted NiO on natural olivine for dry reforming of methane

Directory of Open Access Journals (Sweden)

Grafted NiO on natural olivine for dry reforming of methane C Courson, L Udron, C Petit and A Kiennemann Sci. Technol. Adv. Mater. 3 No 3 (June 2002 271-282 Abstract | References Full text: Acrobat PDF (1.10 MB

2002-01-01

Full Text Available Natural olivine is used for gasification of biomass in a fluidised bed. Characterisations by X-ray diffraction and electron microscopies (SEM and TEM have proved the presence of a (Mg,Fe2SiO4 structure (Mg/Fe ratio: 9/1 with a rather broad distribution in elemental composition. Temperature programmed reduction has revealed equally the presence of iron oxides outside of this structure. The nature of free iron oxides can be both modified by increasing the temperature of calcination and confirmed by measurements of magnetism.The introduction of nickel oxide upon natural olivine is obtained by impregnation with a nitrate salt. The type of interaction of nickel oxide with olivine is different depending upon the preparation method and the calcination temperature. For calcination at 1100 °C, the effects of the amount of NiO and the number of impregnation have been studied. At a high temperature of calcination (1400 °C, NiO is integrated into the olivine structure and the amount of free iron increases. Integrated NiO on olivine is non-reducible, resulting in an inactive catalyst. At lower calcination temperatures grafted NiO is formed, a species which is reduced under catalytic test conditions without aggregation of particles. A single impregnation of nickel (5.5 wt% of NiO gives a stable catalyst activated directly under reaction conditions (CH4+CO2 yielding 96% CO and 76% H2. Catalysts with lower amounts of NiO or a double impregnation of nickel salt lead to a less stable system.Analysis reveals that no change in olivine structure nor size of nickel deposit occurs under test conditions. Equally there are no carbon deposits formed on these catalysts. A model of the evolution of each catalytic system arising from the different preparation methods is proposed. The observed deactivation of such catalysts is attributed to the increase in the amount of free iron, which favours the oxidative properties of the catalytic system.

Synthesis of Ni core NiO shell nanostructure and magnetic investigation for shell thickness determination

International Nuclear Information System (INIS)

Arabi, H.; Bruck, E.; Tichelaar, F.D.

2007-01-01

Full text: Nickel oxide has received a considerable amount of attention in recent years for its catalytic, electronic and magnetic properties. Ni nanoparticles with an average size of 8 nm were prepared by dc - arc discharge in argon atmosphere. A current of 130 A and 300 milli bar pressure of argon have been applied. The produced Ni nanoparticles were annealed for oxidizing in air at 350 for six hours to produce antiferromagnetic NiO particles. The structure of Ni and NiO nanoparticles and size estimation of them studied by means of X-ray diffraction. The size and morphology of the particles were also characterized by high resolution transmission microscopy (TEM). The Ni core NiO shell structure, resulting from the oxidation process, were studied by magnetic properties measurements. A quantum design squid magnetometer, model MPMS5S was used for measuring saturation magnetization of both nanoparticles of Ni with and without NiO layer. By knowing the density of Ni and NiO, we were able to deduce the thickness of the Ni core and NiO outer layer. They are around 3 and 5 nanometers respectively. (authors)

Background gas density and beam losses in NIO1 beam source

Energy Technology Data Exchange (ETDEWEB)

Sartori, E., E-mail: emanuele.sartori@igi.cnr.it; Veltri, P.; Serianni, G. [Consorzio RFX (CNR, ENEA, INFN, Università di Padova, Acciaierie Venete SpA), C.so Stati Uniti 4, 35127 Padova (Italy); Cavenago, M. [INFN-LNL, v.le dell’Università 2, I-35020 Legnaro (PD) (Italy)

2016-02-15

NIO1 (Negative Ion Optimization 1) is a versatile ion source designed to study the physics of production and acceleration of H- beams up to 60 keV. In ion sources, the gas is steadily injected in the plasma source to sustain the discharge, while high vacuum is maintained by a dedicated pumping system located in the vessel. In this paper, the three dimensional gas flow in NIO1 is studied in the molecular flow regime by the Avocado code. The analysis of the gas density profile along the accelerator considers the influence of effective gas temperature in the source, of the gas temperature accommodation by collisions at walls, and of the gas particle mass. The calculated source and vessel pressures are compared with experimental measurements in NIO1 during steady gas injection.

Preparation and electrochemical characteristics of porous hollow spheres of NiO nanosheets as electrodes of supercapacitors

Science.gov (United States)

Yu, Wei; Jiang, Xinbing; Ding, Shujiang; Li, Ben Q.

2014-06-01

Porous hollow nanospheres (or spherical shells) made of NiO nanosheets are synthesized and tested for the electrochemical performance of the electrodes made of these materials for supercapacitors. Preparation of the NiO sheet hollow spheres starts with synthesis of polystyrene nanospheres with carboxyl groups (CPS), followed by a two-step activation procedure and the subsequent nucleation and growth by electroless deposition of Ni on the CPS core to obtain CPS@Ni core-shell nanoparticles. The CPS core is eliminated and metallic Ni nanoshell is converted into NiO by calcinations at high temperatures. The material properties of as-prepared hollow NiO nanospheres are characterized by TEM, XRD and N2-absorption measurements. The electrochemical characteristics of the electrodes made of these nanostructured NiO materials are determined by the CV and galvanostatic measurements. These electrochemical tests indicate that electrodes made of the NiO nanosheet hollow spheres exhibit an improved reversible capacitance of 600 F g-1 after 1000 cycles at a high current density of 10 A g-1. It is believed that the good electrochemical performance of these electrodes is attributed to the improved OH- transport in the porous network structures associated with the hollow spheres of randomly oriented NiO nanosheets.

Steady-state growth of NiO scales on ceria-coated polycrystalline nickel

International Nuclear Information System (INIS)

Czerwinski, F.; Szpunar, J.A.; Smeltzer, W.W.

1996-01-01

The effect of CeO 2 ceramic coatings with thicknesses in the range of 14 to 42 nm on the oxidation of high purity polycrystalline nickel at 973 K in 1 atm O 2 has been studied. The ceria coatings decrease the Ni oxidation rate after 125 h by a factor up to 45, which is significantly higher than the reduction achieved during early stages. Growth features, including oxide thickness, surface morphology, and the texture for both the pure and CeO 2 modified NiO, demonstrate a definite dependence on the crystallographic orientation of the Ni substrate. Oxides with thicknesses of up to 1 microm developed on CeO 2 -coated Ni consisted of three sublayers. The Ce-rich part, composed of small NiO grains and CeO 2 particles, was located inside the scale and shifted deeper into the scale with increased oxidation time. The growth kinetics and microstructural evolutions of modified NiO are discussed in terms of the mechanism of inhibition of grain boundary diffusion in NiO by Ce +4 ions

Erosion behavior of composite Al-Cr cathodes in cathodic arc plasmas in inert and reactive atmospheres

Energy Technology Data Exchange (ETDEWEB)

Franz, Robert, E-mail: robert.franz@unileoben.ac.at; Mendez Martin, Francisca; Hawranek, Gerhard [Montanuniversität Leoben, Franz-Josef-Strasse 18, 8700 Leoben (Austria); Polcik, Peter [Plansee Composite Materials GmbH, Siebenbürgerstrasse 23, 86983 Lechbruck am See (Germany)

2016-03-15

Al{sub x}Cr{sub 1−x} composite cathodes with Al contents of x = 0.75, 0.5, and 0.25 were exposed to cathodic arc plasmas in Ar, N{sub 2}, and O{sub 2} atmospheres and their erosion behavior was studied. Cross-sectional analysis of the elemental distribution of the near-surface zone in the cathodes by scanning electron microscopy revealed the formation of a modified layer for all cathodes and atmospheres. Due to intermixing of Al and Cr in the heat-affected zone, intermetallic Al-Cr phases formed as evidenced by x-ray diffraction analysis. Cathode poisoning effects in the reactive N{sub 2} and O{sub 2} atmospheres were nonuniform as a result of the applied magnetic field configuration. With the exception of oxide islands on Al-rich cathodes, reactive layers were absent in the circular erosion zone, while nitrides and oxides formed in the less eroded center region of the cathodes.

Synopsis of Cathode No.4 Activation

International Nuclear Information System (INIS)

Kwan, Joe; Ekdahl, C.; Harrison, J.; Kwan, J.; Leitner, M.; McCruistian, T.; Mitchell, R.; Prichard, B.; Roy, P.

2006-01-01

The purpose of this report is to describe the activation of the fourth cathode installed in the DARHT-II Injector. Appendices have been used so that an extensive amount of data could be included without danger of obscuring important information contained in the body of the report. The cathode was a 612 M type cathode purchased from Spectra-Mat. Section II describes the handling and installation of the cathode. Section III is a narrative of the activation based on information located in the Control Room Log Book supplemented with time plots of pertinent operating parameters. Activation of the cathode was performed in accordance with the procedure listed in Appendix A. The following sections provide more details on the total pressure and constituent partial pressures in the vacuum vessel, cathode heater power/filament current, and cathode temperature

Effect of NiO inserted layer on spin-Hall magnetoresistance in Pt/NiO/YIG heterostructures

International Nuclear Information System (INIS)

Shang, T.; Zhan, Q. F.; Yang, H. L.; Zuo, Z. H.; Xie, Y. L.; Liu, L. P.; Zhang, S. L.; Zhang, Y.; Li, H. H.; Wang, B. M.; Li, Run-Wei; Wu, Y. H.; Zhang, S.

2016-01-01

We investigate spin-current transport with an antiferromagnetic insulator NiO thin layer by means of the spin-Hall magnetoresistance (SMR) over a wide range of temperature in Pt/NiO/Y_3Fe_5O_1_2 (Pt/NiO/YIG) heterostructures. The SMR signal is comparable to that without the NiO layer as long as the temperature is near or above the blocking temperature of the NiO, indicating that the magnetic fluctuation of the insulating NiO is essential for transmitting the spin current from the Pt to YIG layer. On the other hand, the SMR signal becomes negligibly small at low temperature, and both conventional anisotropic magnetoresistance and the anomalous Hall resistance are extremely small at any temperature, implying that the insertion of the NiO has completely suppressed the Pt magnetization induced by the YIG magnetic proximity effect (MPE). The dual roles of the thin NiO layer are, to suppress the magnetic interaction or MPE between Pt and YIG, and to maintain efficient spin current transmission at high temperature.

A recuperação do patrimônio habitacional

OpenAIRE

Azevedo, Paulo Ormindo David de

1988-01-01

p. 35 - 51 Trata da recuperação do patrimônio habitacional como uma alternativa complementar ao problema do déficit de moradias no Brasil. Passa em revista algumas experiências internacionais e analisa a obsolescência física e funcional do estoque habitacional brasileiro em cidades e setores urbanos centrais de interesse histórico-cultural. Propõe diretrizes para uma política de conservação e recuperação do patrimônio urbano.

SFG investigation of adsorbed CO and NO on NiO(111) surface

Energy Technology Data Exchange (ETDEWEB)

Bandara, Athula; Dobashi, Shinsaku; Kubota, Jun; Onda, Ken; Wada, Akihide; Domen, Kazunari; Hirose, Chiaki [Tokyo Inst. of Tech., Yokohama (Japan). Research Lab. of Resources Utilization; Kano, S.S.

1997-07-01

Adsorption structures of CO and NO on the NiO(111) film grown on Ni(111) crystal have been investigated by sum frequency generation (SFG) spectroscopy and infrared reflection absorption spectroscopy (IRAS). The CO stretching band of adsorbed CO on NiO(111) was observed at 2144 cm{sup -1} on the SFG spectra for both p- and s-polarized visible light. However, adsorbed NO on NiO(111) was observed at 1805 cm{sup -1} on the SFG spectra only for the p-polarized visible light. The results suggest that the adsorbed CO molecule was tilted from the surface normal but the NO molecule was perpendicular to the surface. These orientations of CO and NO reflect the surface structure of NiO(111) which has (2 x 2)-reconstructed microfacets. Adsorption of CO on Ni(111) instead of NiO(111) was also examined by SFG and IRAS. Absorption bands due to linear and bridged CO were observed at 2076 and 1918 cm{sup -1}, respectively, by IRAS. On the other hand, the linear CO molecules on Ni(111) gave an SFG peak at 2076 cm{sup -1} only for the p-polarized visible light indicating the CO molecules are perpendicular to the surface, and bridged CO molecules did not give any SFG signal. The absence of the bridged CO signal is believed to be due to the smaller Raman tensor of bridged CO. (author)

SFG investigation of adsorbed CO and NO on NiO(111) surface

International Nuclear Information System (INIS)

Bandara, Athula; Dobashi, Shinsaku; Kubota, Jun; Onda, Ken; Wada, Akihide; Domen, Kazunari; Hirose, Chiaki; Kano, S.S.

1997-01-01

Adsorption structures of CO and NO on the NiO(111) film grown on Ni(111) crystal have been investigated by sum frequency generation (SFG) spectroscopy and infrared reflection absorption spectroscopy (IRAS). The CO stretching band of adsorbed CO on NiO(111) was observed at 2144 cm -1 on the SFG spectra for both p- and s-polarized visible light. However, adsorbed NO on NiO(111) was observed at 1805 cm -1 on the SFG spectra only for the p-polarized visible light. The results suggest that the adsorbed CO molecule was tilted from the surface normal but the NO molecule was perpendicular to the surface. These orientations of CO and NO reflect the surface structure of NiO(111) which has (2 x 2)-reconstructed microfacets. Adsorption of CO on Ni(111) instead of NiO(111) was also examined by SFG and IRAS. Absorption bands due to linear and bridged CO were observed at 2076 and 1918 cm -1 , respectively, by IRAS. On the other hand, the linear CO molecules on Ni(111) gave an SFG peak at 2076 cm -1 only for the p-polarized visible light indicating the CO molecules are perpendicular to the surface, and bridged CO molecules did not give any SFG signal. The absence of the bridged CO signal is believed to be due to the smaller Raman tensor of bridged CO. (author)

Cathode characterization system: preliminary results with (Ba,Sr,Ca) O coated cathodes

International Nuclear Information System (INIS)

Nono, M.C.A.; Goncalves, J.A.N.; Barroso, J.J.; Dallaqua, R.S.; Spassovsky, I.

1993-01-01

The performance of a cathode characterization system for studying the emission parameters of thermal electron emitters is reported. The system consists of vacuum chamber, power supplies and equipment for measuring and control. Measurements have been taken of the emission current as function of cathode temperature and anode voltage. Several (Ba, Sr) O coated cathodes were tested and the results have shown good agreement with Child's and Richardson's laws. The experimental work function is between 1.0 and 2.0 e V. All emission parameters measured are consistent with international literature data. (author)

Research on an improved explosive emission cathode

International Nuclear Information System (INIS)

Liu Guozhi; Sun Jun; Shao Hao; Chen Changhua; Zhang Xiaowei

2009-01-01

This paper presents a physical description of the cathode plasma process of an explosive emission cathode (EEC) and experimental results on a type of oil-immersed graphite EEC. It is believed that the generation of a cathode plasma is mainly dependent on the state of the cathode surface, and that adsorbed gases and dielectrics on the cathode surface play a leading role in the formation of the cathode plasma. Based on these ideas, a type of oil-immersed graphite EEC is proposed and fabricated. The experiments indicate that the oil-immersed cathodes have improved emissive properties and longer lifetimes.

A facile homogeneous precipitation synthesis of NiO nanosheets and their applications in water treatment

Energy Technology Data Exchange (ETDEWEB)

Zhao, Junfeng, E-mail: daidai02304@163.com [School of Chemistry and Materials Engineering, Changshu Institute of Technology, Changshu (China); Jiangsu Laboratory of Advanced Functional Materials, Changshu Institute of Technology, Changshu (China); Tan, Yang; Su, Kang; Zhao, Junjie; Yang, Chen; Sang, Lingling [School of Chemistry and Materials Engineering, Changshu Institute of Technology, Changshu (China); Lu, Hongbin [National Laboratory of Solid State Microstructures and College of Engineering and Applied Sciences, Nanjing University, Nanjing (China); Chen, JianHua [School of Chemistry and Materials Engineering, Changshu Institute of Technology, Changshu (China); Jiangsu Laboratory of Advanced Functional Materials, Changshu Institute of Technology, Changshu (China)

2015-05-15

Highlights: • NiO nanosheets were synthesized via a facile homogeneous precipitation method. • The NiO nanosheets have a large surface area. • This preparation method was low-cost, simple equipments, easy preparation, short reaction time and better repeatability. • The product also showed a favourable ability to remove Cr(VI) and Congo red (CR) in water treatment. - Abstract: NiO nanosheets were successfully synthesized by a facile homogeneous precipitation method with the assistance of ethanol amine. The sample was characterized by X-ray diffraction (XRD), scanning electronic microscopy (SEM), transmission electron microscopy (TEM), and nitrogen adsorption–desorption techniques. The results demonstrated that the as-prepared product was cubic NiO nanosheets with a large surface area of 170.1 m{sup 2} g{sup −1}. Further, the as-prepared product was used to investigate its potential application for wastewater treatment. The maximum adsorption capacity for Cr(VI) and Congo red (CR) on NiO nanosheets has been determined using the Langmuir equation and found to reach up to 48.98 and 167.73 mg g{sup −1}, respectively. It could be concluded that NiO nanosheets with special surface features had the potential as adsorbents for wastewater treatment.

Metal oxides modified NiO catalysts for oxidative dehydrogenation of ethane to ethylene

KAUST Repository

Zhu, Haibo; Dong, Hailin; Laveille, Paco; Saih, Youssef; Caps, Valerie; Basset, Jean-Marie

2014-01-01

in contrast to pure NiO. The introduction of group IV, V and VI transition metals into NiO decreases the catalytic activity in ethane ODH. However, the ethylene selectivity is enhanced with the highest level for the Ni-W-O and Ni-Ti-O catalysts. As a result

Status of molten carbonate fuel cell technology development

Science.gov (United States)

Parsons, E. L., Jr.; Williams, M. C.; George, T. J.

The MCFC technology has been identified by the DOE as a promising product for commercialization. Development of the MCFC technology supports the National Energy Strategy. Review of the status of the MCFC technology indicates that the MCFC technology developers are making rapid and significant progress. Manufacturing facility development and extensive testing is occurring. Improvements in performance (power density), lower costs, improved packaging, and scale up to full height are planned. MCFC developers need to continue to be responsive to end-users in potential markets. It will be market demands for the correct product definition which will ultimately determine the character of MCFC power plants. There is a need for continued MCFC product improvement and multiple product development tests.

Datalogger usando nios ii

OpenAIRE

Campoverde Rugel, Luis Enrique; Velásquez Vargas, Washington Adrián; Ponguillo, Ronald

2013-01-01

El presente proyecto consiste en la implementación de un Datalogger utilizando el microprocesador NIOS II el cual fue embebido en el FPGA CYCLONE II que se encuentra integrada en la tarjeta de desarrollo ALTERA DE2, el cual obtiene datos de distintos sensores y los almacena en una tarjeta SD Card. Para la realización del proyecto se aplican cuatro etapas. La primera etapa está basada en obtener los datos mediante el uso de sensores y la transmisión usando un PIC, la siguiente etapa se basa...

Low temperature phase transition of the stoichiometric Ln2NiO4 oxides

International Nuclear Information System (INIS)

Fernandez, F.; Saez-Puche, R.; Botto, I.L.; Baran, E.J.

1991-01-01

In this paper we will present a comparative study of the structural phase transition in Ln 2 NiO 4 oxides, by means of neutron diffraction and infrared(IR) spectroscopy. In the Ln 2 NiO 4 oxides (Ln=La, Pr and Nd), there is a low temperature structural phase transition from the orthorhombic symmetry to a tetragonal phase, of first order character. The IR spectra show, at low temperature, a splitting of the bands related with the stretching Ni-O, strongly correlated with the phase transformation. From the neutron data, the phase transition can be visualized as a sudden tilt of the nickel octahedra

Brincando para Lembrar, Memória e Patrimônio na Contemporaneidade

Directory of Open Access Journals (Sweden)

Ildaiane Pintanela Vergara

2016-03-01

Full Text Available Este resumo pretende relatar algumas ações organizadas pelo Laboratório de Educação para o Patrimônio – LEP que envolvem a produção de material educativo e o desenvolvimento de ações educativas no âmbito do patrimônio cultural material e imaterial realizadas em museus da cidade de Pelotas, no Rio Grande do Sul. O LEP está vinculado ao curso de Museologia da Universidade Federal de Pelotas -UFPel entre seus objetivos refletir sobre os museus como agentes educativos e colaborar para a qualificação das ações educativas para o patrimônio desenvolvidas por estas instituições. Para isso, foi desenvolvida uma série de jogos para crianças e adultos, a fim de propiciar uma aproximação agradável, lúdica e pedagógica com alguns bens culturais da cidade de Pelotas que busca a transformação do ato de olhar a partir das ações educativas, resultando na construção de identidade através do referencial do patrimônio.

Air humidity and water pressure effects on the performance of air-cathode microbial fuel cell cathodes

KAUST Repository

Ahn, Yongtae

2014-02-01

To better understand how air cathode performance is affected by air humidification, microbial fuel cells were operated under different humidity conditions or water pressure conditions. Maximum power density decreased from 1130 ± 30 mW m-2 with dry air to 980 ± 80 mW m -2 with water-saturated air. When the cathode was exposed to higher water pressures by placing the cathode in a horizontal position, with the cathode oriented so it was on the reactor bottom, power was reduced for both with dry (1030 ± 130 mW m-2) and water-saturated (390 ± 190 mW m-2) air. Decreased performance was partly due to water flooding of the catalyst, which would hinder oxygen diffusion to the catalyst. However, drying used cathodes did not improve performance in electrochemical tests. Soaking the cathode in a weak acid solution, but not deionized water, mostly restored performance (960 ± 60 mW m-2), suggesting that there was salt precipitation in the cathode that was enhanced by higher relative humidity or water pressure. These results showed that cathode performance could be adversely affected by both flooding and the subsequent salt precipitation, and therefore control of air humidity and water pressure may need to be considered for long-term MFC operation. © 2013 Elsevier B.V. All rights reserved.

Estresse laboral e raciocínio inferencial: um estudo correlacional

Directory of Open Access Journals (Sweden)

Ana Paula Porto Noronha

Full Text Available O objetivo desse estudo foi verificar as relações entre estresse laboral e raciocínio inferencial, sexo e idade. Os instrumentos utilizados foram a escala de vulnerabilidade a estressores no trabalho (EVET e raciocínio inferencial (RIn. Participaram da pesquisa 64 alunos de Psicologia e Engenharia de uma instituição privada do interior do Estado de São Paulo, sendo que, no total, 81,2% eram do sexo masculino, e 18,8%, do sexo feminino, com idade variando de 18 a 45 anos (M=24, DP=5,78. Em relação aos fatores da escala de estresse, encontrou-se correlação negativa significativa entre o fator três (falta de suporte organizacional e o RIn. Dentre as demais análises realizadas, destaca-se a correlação negativa significativa entre EVET e RIn (r =-0,25; p=0,047, o que indica que, quanto maior o estresse, menor a capacidade de raciocínio inferencial.

Fluorine-doped NiO nanostructures: Structural, morphological and spectroscopic studies

Science.gov (United States)

Singh, Kulwinder; Kumar, Manjeet; Singh, Dilpreet; Singh, Manjinder; Singh, Paviter; Singh, Bikramjeet; Kaur, Gurpreet; Bala, Rajni; Thakur, Anup; Kumar, Akshay

2018-05-01

Nanostructured NiO has been prepared by co-precipitation method. In this study, the effect of fluorine doping (1, 3 and 5 wt. %) on the structural, morphological as well as optical properties of NiO nanostructures has been studied. X-ray diffraction (XRD) has employed for studying the structural properties. Cubic crystal structure of NiO was confirmed by the XRD analysis. Crystallite size increased with increase in doping concentration. Nelson-Riley factor (NRF) analysis indicated the presence of defect states in the synthesized samples. Field emission scanning electron microscopy showed the spherical morphology of the synthesized samples and also revealed that the particle size varied with dopant content. The optical properties were studied using UV-Visible Spectroscopy. The results indicated that the band gap energy of the synthesized nanostructures decreased with increase in doping concentration upto 3% but increased as the doping concentration was further raised to 5%. This can be ascribed to the defect states variations in the synthesized samples. The results suggested that the synthesized nanostructures are promising candidate for optoelectronic as well as gas sensing applications.

Cathode material for lithium batteries

Science.gov (United States)

Park, Sang-Ho; Amine, Khalil

2013-07-23

A method of manufacture an article of a cathode (positive electrode) material for lithium batteries. The cathode material is a lithium molybdenum composite transition metal oxide material and is prepared by mixing in a solid state an intermediate molybdenum composite transition metal oxide and a lithium source. The mixture is thermally treated to obtain the lithium molybdenum composite transition metal oxide cathode material.

Cathode erosion in a high-pressure high-current arc: calculations for tungsten cathode in a free-burning argon arc

International Nuclear Information System (INIS)

Nemchinsky, Valerian

2012-01-01

The motion of an evaporated atom of the cathode material in a near-cathode plasma is considered. It is shown that the evaporated atom is ionized almost instantly. The created ion, under the influence of a strong electric field existing in the cathode proximity, has a high probability of returning to the cathode. A small fraction of evaporated atoms are able to diffuse away from the cathode to the region where they are involved in plasma flow and lose their chance to return to the cathode. The fraction of the total evaporated atoms, which do not return to the cathode, the escape factor, determines the net erosion rate. In order to calculate this factor, the distributions of the plasma parameters in the near-cathode plasma were considered. Calculations showed that the escape factor is on the order of a few per cent. Using experimental data on the plasma and cathode temperatures, we calculated the net erosion rate for a free-burning 200 A argon arc with a thoriated tungsten cathode. The calculated erosion rate is close to 1 µg s -1 , which is in agreement with available experimental data. (paper)

Ce doped NiO nanoparticles as selective NO2 gas sensor

Science.gov (United States)

Gawali, Swati R.; Patil, Vithoba L.; Deonikar, Virendrakumar G.; Patil, Santosh S.; Patil, Deepak R.; Patil, Pramod S.; Pant, Jayashree

2018-03-01

Metal oxide gas sensors are promising portable gas detection devices because of their advantages such as low cost, easy production and compact size. The performance of such sensors is strongly dependent on material properties such as morphology, structure and doping. In the present study, we report the effect of cerium (Ce) doping on nickel oxide (NiO) nano-structured thin film sensors towards various gases. Bare NiO and Ce doped NiO nanoparticles (Ce:NiO) were synthesized by sol-gel method. To understand the effect of Ce doping in nickel oxide, various molar percentages of Ce with respect to nickel were incorporated. The structure, phase, morphology and band-gap energy of as-synthesized nanoparticles were studied by XRD, SEM, EDAX and UV-vis spectroscopy. Thin film gas sensors of all the samples were prepared and subjected to various gases such as LPG, NH3, CH3COCH3 and NO2. A systematic and comparative study reveals an enhanced gas sensing performance of Ce:NiO sensors towards NO2 gas. The maximum sensitivity for NO2 gas is around 0.719% per ppm at moderate operating temperature of 150 °C for 0.5% Ce:NiO thin film gas sensor. The enhanced gas sensing performance for Ce:NiO is attributed to the distortion of crystal lattice caused by doping of Ce into NiO.

The effect of cathode geometry on barium transport in hollow cathode plasmas

International Nuclear Information System (INIS)

Polk, James E.; Mikellides, Ioannis G.; Katz, Ira; Capece, Angela M.

2014-01-01

The effect of barium transport on the operation of dispenser hollow cathodes was investigated in numerical modeling of a cathode with two different orifice sizes. Despite large differences in cathode emitter temperature, emitted electron current density, internal xenon neutral and plasma densities, and size of the plasma-surface interaction region, the barium transport in the two geometries is qualitatively very similar. Barium is produced in the insert and flows to the surface through the porous structure. A buildup of neutral Ba pressure in the plasma over the emitter surface can suppress the reactions supplying the Ba, restricting the net production rate. Neutral Ba flows into the dense Xe plasma and has a high probability of being ionized at the periphery of this zone. The steady state neutral Ba density distribution is determined by a balance between pressure gradient forces and the drag force associated with collisions between neutral Ba and neutral Xe atoms. A small fraction of the neutral Ba is lost upstream. The majority of the neutral Ba is ionized in the high temperature Xe plasma and is pushed back to the emitter surface by the electric field. The steady state Ba + ion density distribution results from a balance between electrostatic and pressure forces, neutral Xe drag and Xe + ion drag with the dominant forces dependent on location in the discharge. These results indicate that hollow cathodes are very effective at recycling Ba within the discharge and therefore maintain a high coverage of Ba on the emitter surface, which reduces the work function and sustains high electron emission current densities at moderate temperatures. Barium recycling is more effective in the cathode with the smaller orifice because the Ba is ionized in the dense Xe plasma concentrated just upstream of the orifice and pushed back into the hollow cathode. Despite a lower emitter temperature, the large orifice cathode has a higher Ba loss rate through the orifice because the Xe

Fabrication of the cube textured NiO buffer layer by line-focused infrared heating for coated conductor application

International Nuclear Information System (INIS)

Chung, Jun-Ki; Kim, Won-Jeong; Tak, Jinsung; Kim, Cheol Jin

2007-01-01

Epitaxial growth of NiO on the bi-axially textured Ni-3 at.%W (Ni-3W) substrate as seed layer for coated conductor were studied. The bi-axially textured NiO was formed on the Ni-3W tapes using a line-focused infrared heater by oxidizing the surface of the substrate at 800-950 deg. C for 15-120 s in oxygen atmosphere. The thickness of the NiO layer could be controlled by changing heat-treatment, which was estimated as approximately 200-500 nm in the cross-sectional SEM micrographs of the NiO/Ni template. This thickness is enough to block the diffusion of the Ni in the substrate to the superconducting layer. The samples showed strong texture development of NiO layer. The sample oxidized at 900 deg. C with the tape transferring speed of 30 mm/h exhibited ω-scan full width at half maximum (FWHM) values for Ni-3W(2 0 0) and NiO(2 0 0) were 3.97 deg., and 3.67 deg., and φ-scan FWHM values for Ni-3W(1 1 1) and NiO(1 1 1) were 9.58 deg., and 8.79 deg., respectively. Also, the (1 1 1) pole-figure of the NiO buffer layer showed the good symmetry of the four peaks, securing the epitaxial growth of the buffer layers on the NiO layer. Also NiO layer exhibited root-mean-square roughness value of 39 nm by AFM (10 x 10 μm) investigation

Cathodic protection -- Rectifier 47

International Nuclear Information System (INIS)

Lane, W.M.

1995-01-01

This Acceptance Test Procedure (ATP) has been prepared to demonstrate that the cathodic protection system functions as required by project criteria. The cathodic protection system is for the tank farms at the Hanford Reservation. The tank farms store radioactive waste

Cathodic protection -- Rectifier 46

International Nuclear Information System (INIS)

Lane, W.M.

1995-01-01

This Acceptance Test Procedure (ATP) has been prepared to demonstrate that the cathodic protection system functions as required by project criteria. The cathodic protection system is for the tank farms on the Hanford Reservation. The tank farms store radioactive waste

Cathode R&D for Future Light Sources

Energy Technology Data Exchange (ETDEWEB)

Dowell, D.H.; /SLAC; Bazarov, I.; Dunham, B.; /Cornell U., CLASSE; Harkay, K.; /Argonne; Hernandez-Garcia; /Jefferson Lab; Legg, R.; /Wisconsin U., SRC; Padmore, H.; /LBL, Berkeley; Rao, T.; Smedley, J.; /Brookhaven; Wan, W.; /LBL, Berkeley

2010-05-26

This paper reviews the requirements and current status of cathodes for accelerator applications, and proposes a research and development plan for advancing cathode technology. Accelerator cathodes need to have long operational lifetimes and produce electron beams with a very low emittance. The two principal emission processes to be considered are thermionic and photoemission with the photocathodes being further subdivided into metal and semi-conductors. Field emission cathodes are not included in this analysis. The thermal emittance is derived and the formulas used to compare the various cathode materials. To date, there is no cathode which provides all the requirements needed for the proposed future light sources. Therefore a three part research plan is described to develop cathodes for these future light source applications.

Mechanistic Enhancement of SOFC Cathode Durability

Energy Technology Data Exchange (ETDEWEB)

Wachsman, Eric [Univ. of Maryland, College Park, MD (United States)

2016-02-01

Durability of solid oxide fuel cells (SOFC) under “real world” conditions is an issue for commercial deployment. In particular cathode exposure to moisture, CO2, Cr vapor (from interconnects and BOP), and particulates results in long-term performance degradation issues. Here, we have conducted a multi-faceted fundamental investigation of the effect of these contaminants on cathode performance degradation mechanisms in order to establish cathode composition/structures and operational conditions to enhance cathode durability.

Two-beam virtual cathode accelerator

International Nuclear Information System (INIS)

Peter, W.

1992-01-01

A proposed method to control the motion of a virtual cathode is investigated. Applications to collective ion acceleration and microwave generation are indicated. If two counterstreaming relativistic electron beams of current I are injected into a drift tube of space-charge-limiting current I L = 2I, it is shown that one beam can induce a moving virtual cathode in the other beam. By dynamically varying the current injected into the drift tube region, the virtual cathode can undergo controlled motion. For short drift tubes, the virtual cathodes on each end are strongly-coupled and undergo coherent large-amplitude spatial oscillations within the drift tube

Template-less surfactant-free hydrothermal synthesis NiO nanoflowers and their photoelectrochemical hydrogen production

KAUST Repository

Qurashi, Ahsanulhaq

2015-12-01

A facile direct surfactant-free template-less hydrothermal method is employed for the growth of high surface-area NiO nanoflowers made up of complex and assembled nanosheets network.Field emission scanning electron microscopy revealed that each nanosheet is about 50-60nm thick. Detailed structural analysis reveals single-crystalline nature of NiO nanoflowers with cubic crystal structure. The optical absorption bands in the wavelength range of 350-800nm illustrated in terms of ligand field theory. The photoelectrochemical (PEC), water splitting performance on the NiO nanoflowers were also investigated. © 2015 Hydrogen Energy Publications, LLC.

Template-less surfactant-free hydrothermal synthesis NiO nanoflowers and their photoelectrochemical hydrogen production

KAUST Repository

Qurashi, Ahsanulhaq; Zhang, Zhongai; Asif, M.; Yamazaki, Toshinari

2015-01-01

A facile direct surfactant-free template-less hydrothermal method is employed for the growth of high surface-area NiO nanoflowers made up of complex and assembled nanosheets network.Field emission scanning electron microscopy revealed that each nanosheet is about 50-60nm thick. Detailed structural analysis reveals single-crystalline nature of NiO nanoflowers with cubic crystal structure. The optical absorption bands in the wavelength range of 350-800nm illustrated in terms of ligand field theory. The photoelectrochemical (PEC), water splitting performance on the NiO nanoflowers were also investigated. © 2015 Hydrogen Energy Publications, LLC.

Synthesis, structural and paramagnetic properties of SnO{sub 2} doped NiO nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Islam, I., E-mail: ishtihadahislam@gmail.com; Dwivedi, Sonam; Dar, Hilal A.; Dar, M. A.; Varshney, Dinesh, E-mail: vdinesh33@rediffmail.com [School of Physics, Vigyan Bhawan, Devi Ahilya University, Khandwa Road Campus, Indore 452001 (India)

2016-05-06

In this work, Sn doped NiO nanoparticles were synthesized by co-precipitation route to explore the impact of doping on lattice structure, dielectric constant and magnetization. X-ray diffraction analysis confirmed cubic (Fd-3m) structure of Sn doped NiO. Average crystallite size decreases from 78.2 nm (Ni{sub 0.95}Sn{sub 0.05}O) to 64.23 nm (Ni{sub 0.8}Sn{sub 0.2}O). Scanning electron microscopy images confirm that nanocrystals have agglomerated spherical morphology. The Raman spectrum exhibits a strong, broad peak at 410 cm{sup -1} and is attributed to the Ni-O stretching mode and doped samples show a blue shift. The dielectric constants at about 1 Hz are measured to be about 1.795, 1.030, 0.442, and 0.302 × 10{sup 3} Ni{sub 1-x}Sn{sub x}O (x = 0.05, 0.1, 0.15, 0.2), respectively. The dielectric constant in nanoparticles of doped Ni{sub 1-x}Sn{sub x}O is three orders of magnitude higher as compared to pure NiO ceramics. The nature of magnetization - applied field (M-H) infers paramagnetic behaviour for Sn doped NiO nanoparticles.

Electron emission from pseudospark cathodes

International Nuclear Information System (INIS)

Anders, A.; Anders, S.; Gundersen, M.A.

1994-01-01

The pseudospark cathode has the remarkable property of macroscopically homogeneous electron emission at very high current density (>1 kA/cm 2 ) over a large area (some cm 2 ). The model of electron emission presented here is based on the assumption that the pseudospark microscopically utilizes explosive arc processes, as distinct from earlier models of ''anomalous emission in superdense glow discharges.'' Explosive emission similar to vacuum are cathode spots occurs rapidly when the field strength is sufficiently high. The plasma remains macroscopically homogeneous since the virtual plasma anode adapts to the cathode morphology so that the current is carried by a large number of homogeneously distributed cathode spots which are similar to ''type 1'' and ''type 2'' spots of vacuum arc discharges. The net cathode erosion is greatly reduced relative to ''spark gap-type'' emission. At very high current levels, a transition to highly erosive spot types occurs, and this ''arcing'' leads to a significant reduction in device lifetime. Assuming vacuum-arc-like cathode spots, the observed current density and time constants can be easily explained. The observed cathode erosion rate and pattern, recent fast-camera data, laser-induced fluorescence, and spectroscopic measurements support this approach. A new hypothesis is presented explaining current quenching at relatively low currents. From the point of view of electron emission, the ''superdense glow'' or ''superemissive phase'' of pseudosparks represents an arc and not a glow discharge even if no filamentation or ''arcing'' is observed

Long-term (30 days toxicity of NiO nanoparticles for adult zebrafish Danio rerio

Directory of Open Access Journals (Sweden)

Kovrižnych Jevgenij A.

2014-03-01

Full Text Available Nickel oxide in the form of nanoparticles (NiO NPs is extensively used in different industrial branches. In a test on adult zebrafish, the acute toxicity of NiO NPs was shown to be low, however longlasting contact with this compound can lead to its accumulation in the tissues and to increased toxicity. In this work we determined the 30-day toxicity of NiO NPs using a static test for zebrafish Danio rerio. We found the 30-day LC50 value to be 45.0 mg/L, LC100 (minimum concentration causing 100% mortality was 100.0 mg/L, and LC0 (maximum concentration causing no mortality was 6.25 mg/L for adult individuals of zebrafish. Considering a broad use of Ni in the industry, NiO NPs chronic toxicity may have a negative impact on the population of aquatic organisms and on food web dynamics in aquatic systems.

Cold cathode arc model in mercury discharges

International Nuclear Information System (INIS)

Li, Y.M.; Byszewski, W.W.; Budinger, A.B.

1990-01-01

Voltage/current characteristics measured during the starting of metal halide lamps indicate a low voltage discharge when condensates (mainly mercury) are localized on the electrodes. In this case, even with a cold cathode which does not emit electrons, the current is very high and voltage across the lamp drops to about 15 to 20 V. This type of discharge is similar to the cold cathode mercury vapor arc found in mercury pool rectifiers. The cathode sheath in the mercury vapor arc is characterized by very small cathode spot size, on the order of 10 -c cm 2 , very high current density of about 10 6 A/cm 2 and very low cathode fall of approximately 10 volts. The discharge is modified and generalized to describe the cathode phenomena in the cold cathode mercury vapor arc. The sensitivity of calculated discharge parameters with respect to such modifications were examined. Results show that the cathode fall voltage remains fairly constant (7-8 volts) with large fractional variations of metastable mercury atoms bombarding the cathode. This result compares very well with experimental waveforms when anode fall and plasma voltage approximations are incorporated

Electron emission mechanism of carbon fiber cathode

International Nuclear Information System (INIS)

Liu Lie; Li Limin; Wen Jianchun; Wan Hong

2005-01-01

Models of electron emission mechanism are established concerning metal and carbon fiber cathodes. Correctness of the electron emission mechanism was proved according to micro-photos and electron scanning photos of cathodes respectively. The experimental results and analysis show that the surface flashover induces the electron emission of carbon fiber cathode and there are electron emission phenomena from the top of the carbon and also from its side surface. In addition, compared with the case of the stainless steel cathode, the plasma expansion velocity for the carbon fiber cathode is slower and the pulse duration of output microwave can be widened by using the carbon fiber cathode. (authors)

Azadirachta indica (neem) leaves mediated synthesis of SnO2/NiO nanocomposite and assessment of its photocatalytic activity

Science.gov (United States)

Varshney, Bhaskar; Shoeb, Mohd; Siddiqui, M. J.; Azam, Ameer; Mobin, Mohammad

2018-05-01

SnO2/NiO nanocomposite are prepared by using a simple cost effective and ecofriendly green soft template method followed by ultrasonication treatment further by calcination at 300 °C. The resulting nanocatalysts were characterized by X-ray diffraction (XRD), UV-Visible spectroscopy and transmission electron microscopy (TEM). The SnO2-NiO photocatalyst was made of a mesoporous network of aggregated NiO and cassiterite SnO2 nanocrystallites, the size of which was estimated to be 16.68 nm and 13.17 nm, respectively, after calcination. According to UV-visible spectroscopy, the evident energy band gap value of the SnO2-NiO photocatalyst was estimated to be 3.132 eV to be compared with those of pure SnO2, that is, 3.7 eV. Moreover, the heterostructure SnO2-NiO photocatalyst showed much higher photocatalytic activities for the degradation of methylene blue than those of individual SnO2 and NiO nanomaterials. This behaviour was rationalized in terms of better charge separation and the suppression of charge recombination in the SnO2-NiO photocatalyst because of the energy difference between the conduction band edges of SnO2 and NiO as evidenced by the band alignment determination. Finally, this mesoporous SnO2-NiO heterojunction nanocatalyst was stable and could be easily recycled several times opening new avenues for potential industrial applications.

Microwave hydrothermal synthesis of urchin-like NiO nanospheres as electrode materials for lithium-ion batteries and supercapacitors with enhanced electrochemical performances

Energy Technology Data Exchange (ETDEWEB)

Mondal, Anjon Kumar, E-mail: Anjon.K.Mondal@student.uts.edu.au [Centre for Clean Energy Technology, School of Chemistry and Forensic Science, University of Technology Sydney, Broadway, Sydney, NSW 2007 (Australia); Su, Dawei; Wang, Ying; Chen, Shuangqiang [Centre for Clean Energy Technology, School of Chemistry and Forensic Science, University of Technology Sydney, Broadway, Sydney, NSW 2007 (Australia); Liu, Qi [School of Petrochemical Engineering, Changzhou University, Changzhou 213164 (China); Wang, Guoxiu, E-mail: Guoxiu.wang@uts.edu.au [Centre for Clean Energy Technology, School of Chemistry and Forensic Science, University of Technology Sydney, Broadway, Sydney, NSW 2007 (Australia)

2014-01-05

Highlights: • Urchin-like NiO nanospheres were synthesised by a microwave hydrothermal method. • The NiO nanospheres consist of nanocrystals and porous structure. • NiO nanospheres exhibited a high reversible specific capacity of 1027 mA h g{sup −1}. • The NiO nanospheres also delivered a high supercapacitance of 736 F g{sup −1}. -- Abstract: Urchin-like NiO nanospheres were synthesised by a microwave hydrothermal method. The as-synthesised NiO nanospheres were characterised by X-ray diffraction, field emission scanning electron microscopy and transmission electron microscopy. It was found that NiO nanosphere consists of a nanoporous structure and nanosize crystals. When applied as anode materials in lithium-ion batteries, NiO nanospheres exhibited a high reversible specific capacity of 1027 mA h g{sup −1}, an excellent cycling performance and a good high rate capability. NiO nanospheres also showed a high specific capacitance as electrode materials for supercapacitors.

NiO(111) nanosheets as efficient and recyclable adsorbents for dye pollutant removal from wastewater

International Nuclear Information System (INIS)

Song Zhi; Hu Juncheng; Chen Lifang; Richards, Ryan

2009-01-01

Semiconductor single-crystalline polar NiO(111) nanosheets with well-defined hexagonal holes have been investigated for application in dye adsorption and combustion processes. With regard to adsorption technologies, high surface area metal oxides have an advantage over activated carbon in that the adsorbed species can be combusted and the adsorbent reused in the case of metal oxides while regeneration of activated carbon remains challenging and thus the adsorbent/adsorbate system must be disposed of. Here, three typical textile dyes, reactive brilliant red X-3B, congo red and fuchsin red, were studied for removal from wastewater with two NiO systems and activated carbon. These studies revealed that the NiO(111) nanosheets exhibited much more favorable adsorptive properties than conventionally prepared nickel oxide powder (CP-NiO) obtained from thermal decomposition of nickel nitrate. The maximum adsorption capabilities of the three dyes on NiO(111) nanosheets reached 30.4 mg g -1 , 35.15 mg g -1 and 22 mg g -1 for reactive brilliant red X-3B, congo red and fuchsin acid, respectively, while the maximum adsorption capabilities of the three dyes on CP-NiO were only 8.4, 13.2 and 12 mg g -1 for reactive brilliant red X-3B, congo red and fuchsin acid. To simulate the adsorption isotherm, two commonly employed models, the Langmuir and the Freundlich isotherms, were selected to explicate the interaction of the dye and NiO(111). The isotherm evaluations revealed that the Langmuir model demonstrated better fit to experimental equilibrium data than the Freundlich model. The maximum predicted adsorption capacity was 36.1 mg g -1 . In addition, adsorption kinetic data of NiO(111) followed a pseudo-second-order rate for congo red. These studies infer that NiO(111) nanosheets possess desirable properties for application in adsorption and combustion applications.

Growth and Characteristic of Amorphous Nano-Granular TeO2-V2O5-NiO Thin Films

Science.gov (United States)

Hosseinzadeh, Sh.; Rahmati, A.; Bidadi, H.

2016-12-01

TeO2-V2O5-NiO thin films were deposited using thermal evaporation from 40TeO2-(60-y)V2O5-yNiO (y=0-30mol%) target. Structural analysis of the films was identified by X-ray diffractometry (XRD) and scanning electron microscopy (SEM). The amorphous TeO2-V2O5-NiO films have nanosized clear grain structure and sharp grain boundaries. DC conductivity and current-voltage (I-V) characteristic of TeO2-V2O5-NiO thin films were measured in the temperature range of 300-423K. As nickel oxide (NiO) content increases, the DC conductivity decreases up to two orders in value (10-9-10-11Sṡcm-1). Temperature dependence of conductivity is described using the small polaron hopping (SPH) model as well. Poole-Frenkel effect is observed at high external electric field. The optical absorption spectra of the TeO2-V2O5-NiO thin films were recorded in the wavelength range of 380-1100nm. The absorption coefficient revealed bandgap shrinkage (3.01-2.3eV) and band tail widening, due to an increase in NiO content. Energy dispersive X-ray spectroscopy (EDX) was used to determine elemental composition. In TeO2-V2O5-NiO thin films, the NiO content is around fifth of the initial target.

CdTeO3 Deposited Mesoporous NiO Photocathode for a Solar Cell

Directory of Open Access Journals (Sweden)

Chuan Zhao

2014-01-01

Full Text Available Semiconductor sensitized NiO photocathodes have been fabricated by successive ionic layer adsorption and reaction (SILAR method depositing CdTeO3 quantum dots onto mesoscopic NiO films. A solar cell using CdTeO3 deposited NiO mesoporous photocathode has been fabricated. It yields a photovoltage of 103.7 mV and a short-circuit current density of 0.364 mA/cm2. The incident photon to current conversion efficiency (IPCE value is found to be 12% for the newly designed NiO/CdTeO3 solar cell. It shows that the p-type NiO/CdTeO3 structure could be successfully utilized to fabricate p-type solar cell.

Plasma processes inside dispenser hollow cathodes

International Nuclear Information System (INIS)

Mikellides, Ioannis G.; Katz, Ira; Goebel, Dan M.; Polk, James E.; Jameson, Kristina K.

2006-01-01

A two-dimensional fluid model of the plasma and neutral gas inside dispenser orificed hollow cathodes has been developed to quantify plasma processes that ultimately determine the life of the porous emitters inserted in these devices. The model self-consistently accounts for electron emission from the insert as well as for electron and ion flux losses from the plasma. Two cathodes, which are distinctively different in size and operating conditions, have been simulated numerically. It is found that the larger cathode, with outer tube diameter of 1.5 cm and orifice diameter of 0.3 cm, establishes an effective emission zone that spans approximately the full length of the emitter when operated at a discharge current of 25 A and a flow rate of 5.5 sccm. The net heating of the emitter is caused by ions that are produced by ionization of the neutral gas inside the tube and are then accelerated by the sheath along the emitter. The smaller cathode, with an outer diameter of 0.635 cm and an orifice diameter of 0.1 cm, does not exhibit the same operational characteristics. At a flow rate of 4.25 sccm and discharge current of 12 A, the smaller cathode requires 4.5 times the current density near the orifice and operates with more than 6 times the neutral particle density compared to the large cathode. As a result, the plasma particle density is almost one order of magnitude higher compared to the large cathode. The plasma density in this small cathode is high enough such that the Debye length is sufficiently small to allow 'sheath funneling' into the pores of the emitter. By accessing areas deeper into the insert material, it is postulated that the overall emission of electrons is significantly enhanced. The maximum emission current density is found to be about 1 A/mm 2 in the small cathode, which is about one order of magnitude higher than attained in the large cathode. The effective emission zone in the small cathode extends to about 15% of the emitter length only, and the

Compact Rare Earth Emitter Hollow Cathode

Science.gov (United States)

Watkins, Ronald; Goebel, Dan; Hofer, Richard

2010-01-01

A compact, high-current, hollow cathode utilizing a lanthanum hexaboride (LaB6) thermionic electron emitter has been developed for use with high-power Hall thrusters and ion thrusters. LaB6 cathodes are being investigated due to their long life, high current capabilities, and less stringent xenon purity and handling requirements compared to conventional barium oxide (BaO) dispenser cathodes. The new cathode features a much smaller diameter than previously developed versions that permit it to be mounted on axis of a Hall thruster ( internally mounted ), as opposed to the conventional side-mount position external to the outer magnetic circuit ("externally mounted"). The cathode has also been reconfigured to be capable of surviving vibrational loads during launch and is designed to solve the significant heater and materials compatibility problems associated with the use of this emitter material. This has been accomplished in a compact design with the capability of high-emission current (10 to 60 A). The compact, high-current design has a keeper diameter that allows the cathode to be mounted on the centerline of a 6- kW Hall thruster, inside the iron core of the inner electromagnetic coil. Although designed for electric propulsion thrusters in spacecraft station- keeping, orbit transfer, and interplanetary applications, the LaB6 cathodes are applicable to the plasma processing industry in applications such as optical coatings and semiconductor processing where reactive gases are used. Where current electrical propulsion thrusters with BaO emitters have limited life and need extremely clean propellant feed systems at a significant cost, these LaB6 cathodes can run on the crudest-grade xenon propellant available without impact. Moreover, in a laboratory environment, LaB6 cathodes reduce testing costs because they do not require extended conditioning periods under hard vacuum. Alternative rare earth emitters, such as cerium hexaboride (CeB6) can be used in this

Improvement of in-plane alignment for surface oxidized NiO layer on textured Ni substrate by two-step heat-treatment

International Nuclear Information System (INIS)

Hasegawa, Katsuya; Izumi, Toru; Izumi, Teruo; Shiohara, Yuh; Maeda, Toshihiko

2004-01-01

Epitaxial growth of NiO on a textured Ni substrate as a template for an REBa 2 Cu 3 O y coated conductor was investigated. Highly in-plane aligned NiO layers were successfully fabricated using a new process of a two-step heat-treatment for oxidation. In the first-step, a highly in-plane aligned thin NiO layer was formed on a textured Ni substrate under a low driving force of oxidation. Then, in the second-step, a thick NiO layer was grown at a higher rate with maintaining its high in-plane grain alignment, as if the first NiO layer acts as a seed crystal layer. Further, growth rates and microstructures of the NiO layers were studied comparatively in the cases with and without the first layer. It was found that the oxidation rate in the case with the first layer was lower than that without the first layer. The microstructure observation revealed that the NiO without the first layer was poly-crystalline with many grain-boundaries. On the other hand, in the case with the first layer, grain-boundaries of the NiO were hardly observed. Hence, the reason for this difference of the growth rate and the microstructure of the NiO layers were discussed in view of a diffusivity path

Non-basic solution eco-routes to nano-scale NiO with different shapes: Synthesis and application

International Nuclear Information System (INIS)

Wang Xiangyan; Wan Lijuan; Yu Tao; Zhou Yong; Guan Jie; Yu, Zhentao; Li, Zhaosheng; Zou Zhigang

2011-01-01

Research highlights: → NiO nanodiscs and nanoflowers have been controllably fabricated via the thermal decomposition of Ni(OH) 2 by using different Ni sources in non-basic solution for anion-assisted effect. → The route is environment-friendly. → The nanoflowers exhibit better performance than the nanodiscs when they are applied in electrochemical test and water treatment. - Abstract: The assembly of NiO nanodiscs (namely nanoflowers) as well as the dispersed NiO nanodiscs have been successfully synthesized via the thermal decomposition of Ni(OH) 2 obtained from different Ni sources in non-basic solution. The route is environment-friendly. The materials were characterized by X-ray diffraction (XRD), field-emission scanning electron microscope (FE-SEM), transmission electron microscope (TEM) and N 2 adsorption-desorption. The porous structures with pore size around 6 nm can be observed on the single NiO disc. The nanoflowers exhibit better performance than nanodiscs in the electrochemical test and water treatment experiments, due to much more available surface areas and spaces formed in the NiO nanoflowers.

Preparation and characterization of Eosin B- and Erythrosin J-sensitized nanostructured NiO thin film photocathodes

Energy Technology Data Exchange (ETDEWEB)

Vera, F. [Instituto de Quimica, Universidad Catolica de Valparaiso, Valparaiso (Chile); Schrebler, R. [Instituto de Quimica, Universidad Catolica de Valparaiso, Valparaiso (Chile); Munoz, E. [Instituto de Quimica, Universidad Catolica de Valparaiso, Valparaiso (Chile); Suarez, C. [Instituto de Quimica, Universidad Catolica de Valparaiso, Valparaiso (Chile); Cury, P. [Instituto de Quimica, Universidad Catolica de Valparaiso, Valparaiso (Chile); Gomez, H. [Instituto de Quimica, Universidad Catolica de Valparaiso, Valparaiso (Chile); Cordova, R. [Instituto de Quimica, Universidad Catolica de Valparaiso, Valparaiso (Chile); Marotti, R.E. [Instituto de Fisica, Facultad de Ingenieria, Universidad de la Republica, Herrera y Reissig 565, C.C. 30, 11000 Montevideo (Uruguay); Dalchiele, E.A. [Instituto de Fisica, Facultad de Ingenieria, Universidad de la Republica, Herrera y Reissig 565, C.C. 30, 11000 Montevideo (Uruguay)]. E-mail: dalchiel@fing.edu.uy

2005-11-01

Nickel oxide (NiO) thin films were prepared onto ITO/glass substrates by spin-coating, dipping and electrochemically. Studies of the morphological and structural properties of the films were done by atomic force microscopy (AFM). Photoelectrochemical and optical experiments were carried out in order to characterize the semiconductor properties of the nanostructured NiO thin films. The experiments were also done for Eosin B- and Erythrosin J-sensitized nanostructured NiO films, with the aim to visualize their potential application as photocatodes in tandem dye-sensitized solar cells (TDSSC). The NiO grown by dipping was the one presenting the best morphological properties. The photoelectrochemical results for all the bare NiO, NiO-Eosin B and NiO-Erythrosin J/electrolyte (I{sub 2}/I{sup -}) systems showed a p-type behavior. An enhancement in the photocurrent has been observed for the systems sensitized with the dyes. For the NiO/Erythrosin J system the enhancement of the current under illumination in comparison to the dark current was about 200%.

Preparation and characterization of Eosin B- and Erythrosin J-sensitized nanostructured NiO thin film photocathodes

International Nuclear Information System (INIS)

Vera, F.; Schrebler, R.; Munoz, E.; Suarez, C.; Cury, P.; Gomez, H.; Cordova, R.; Marotti, R.E.; Dalchiele, E.A.

2005-01-01

Nickel oxide (NiO) thin films were prepared onto ITO/glass substrates by spin-coating, dipping and electrochemically. Studies of the morphological and structural properties of the films were done by atomic force microscopy (AFM). Photoelectrochemical and optical experiments were carried out in order to characterize the semiconductor properties of the nanostructured NiO thin films. The experiments were also done for Eosin B- and Erythrosin J-sensitized nanostructured NiO films, with the aim to visualize their potential application as photocatodes in tandem dye-sensitized solar cells (TDSSC). The NiO grown by dipping was the one presenting the best morphological properties. The photoelectrochemical results for all the bare NiO, NiO-Eosin B and NiO-Erythrosin J/electrolyte (I 2 /I - ) systems showed a p-type behavior. An enhancement in the photocurrent has been observed for the systems sensitized with the dyes. For the NiO/Erythrosin J system the enhancement of the current under illumination in comparison to the dark current was about 200%

Probing the 4p electron-spin polarization in NiO

International Nuclear Information System (INIS)

Neubeck, W.; Vettier, C.; Bergevin, F. de; Yakhou, F.; Mannix, D.; Bengone, O.; Alouani, M.; Barbier, A.

2001-01-01

K-edge resonant x-ray magnetic scattering experiments have been performed on antiferromagnetic NiO. The observation of two resonances at the K edge allows the construction of models to compare the electronic properties of NiO and the observed resonant magnetic x-ray scattering. From the polarization analysis of the scattered beam, a quadrupolar transition (1s-3d) and a dipolar transition (1s-4p) are identified. While the quadrupolar transition can be modeled using an atomic picture for the 3d electrons, the dipolar transition is associated to a broadband structure of p electrons and its energy profile is compared to electronic band-structure calculations

Sol-gel-processed yttrium-doped NiO as hole transport layer in inverted perovskite solar cells for enhanced performance

Science.gov (United States)

Hu, Zijun; Chen, Da; Yang, Pan; Yang, Lijun; Qin, Laishun; Huang, Yuexiang; Zhao, Xiaochong

2018-05-01

In this work, high-performance inverted planar perovskite solar cells (PSCs) using sol-gel processed Y-doped NiO thin films as hole transport layer (HTL) were demonstrated. Y-doped NiO thin films containing different Y doping concentrations were successfully prepared through a simple sol-gel process. The Y doping could significantly improve the electrical conductivity of NiO thin film, and the photovoltaic performance of Y-doped NiO HTL-based PSC devices outperformed that of the pristine NiO HTL-based device. Notably, the PSC using a 5%Y-NiO HTL exhibited the champion performance with an open-circuit voltage (Voc) of 1.00 V, a short circuit current density (Jsc) of 23.82 mA cm-2, a fill factor (FF) of 68% and a power conversion efficiency (PCE) of 16.31%, resulting in a 27.62% enhancement in PCE in comparison with the NiO device. The enhanced performance of the Y-doped NiO device could be attributed to the improved hole mobility, the high quality compact active layer morphology, the more efficient charge extraction from perovskite absorber as well as the lower recombination probability of charge carriers. Thus, this work provides a simple and effective approach to improve the electrical conductivity of p-type NiO thin films for use as a promising HTL in high performance PSCs.

O patrimônio cultural afro-brasileiro: São José, um estudo de caso

Directory of Open Access Journals (Sweden)

Joana Célia dos Passos

2016-04-01

Full Text Available Resumo O presente texto apresenta os resultados de um estudo de caso que teve como objetivo analisar como e o que tem sido considerado pelo poder público bem patrimonial da população afro-brasileira em um município catarinense.Analisa também o que pensam os moradores(as sobre os bens patrimoniais da população. Foram utilizados como procedimentos: análise documental, aplicação de questionário e entrevistas. Como resultado, constatou-se que os referenciais de patrimônio cultural simbolicamente atuantes ainda são os tradicionais patrimônios "a pedra e cal". Nessa perspectiva, o patrimônio cultural associado à população afro-brasileira fica excluído, em grande medida, porque popularmente não é visto como patrimônio cultural.

Directional waverider buoy in Indian waters - Experiences of NIO

Digital Repository Service at National Institute of Oceanography (India)

AshokKumar, K.; Diwan, S.G.

, receiving/ recording unit, NIO's experience in mooring, deployment and retrieval operations etc. The paper also highlights various operational problems during the data collection programme. Suggestions and conclusions pertaining to operation, maintenance etc...

Preservação do patrimônio arqueológico em terras indígenas

OpenAIRE

Robrahn-González, Erika; Migliacio, Maria Clara

2015-01-01

Este artigo apresenta o resultado do trabalho desenvolvido durante o “I Seminário Internacional de Gestão do Patrimônio Arqueológico Pan-Amazônico”, promovido em novembro/2007 pelo Instituto do Patrimônio Histórico e Artístico Nacional (IPHAN) na cidade de Manaus/ AM, mais especificamente, na Sessão Temática intitulada “Preservação do Patrimônio Arqueológico em Terras Indígenas”.

Zn doping induced conductivity transformation in NiO films for realization of p-n homo junction diode

Science.gov (United States)

Dewan, Sheetal; Tomar, Monika; Tandon, R. P.; Gupta, Vinay

2017-06-01

Mixed transition metal oxide, zinc doped NiO, Z n x N i 1 - x O (x = 0, 0.01, 0.02, 0.05, and 0.10), thin films have been fabricated by the RF magnetron sputtering technique in an oxygen deficit ambience at a growth temperature of 400 °C. The present report highlights the effect of Zn doping in NiO thin films on its structural, optical, and electrical properties. Optical transmission enhancement and band gap engineering in a-axis oriented NiO films have been demonstrated via Zn substitution. Hall effect measurements of the prepared samples revealed a transition from p-type to n-type conductivity in NiO at 2% Zn doping. A NiO based transparent p-n homojunction diode has been fabricated successfully, and the conduction mechanism dominating the diode properties is reported in detail. Current-voltage (I-V) characteristics of the homojunction diode are found to obey the Space Charge Limited Conduction mechanism with non-ideal square law behaviour.

LUCRO, VALOR CONTABIL E DIVIDENDOS NA AVALIAcAO DO PATRIMÔNIO LIQUIDO

Directory of Open Access Journals (Sweden)

James A. Ohlson

2009-09-01

Full Text Available A contabilidade atribui uma importante função integrativa a demonstração das mutações do patrimônio liquido. A demonstração inclui os itens mais importantes do balanço o e da demonstração de resultado do exercício - o valor do patrimônio liquido e o lucro - e sua forma de apresentação exige que a alteração no valor do patrimônio liquido seja igual ao lucro menos os dividendos (líquidos das contribuições para aumento de capital. Referimo-nos a essa relação corno sendo a “relação de lucro limpo", pois, da forma como foi articulada, todas as alterações nos ativos e passivos que não estejam relacionadas com os dividendos devem passar pela demonstração de resultado do exercício. A teoria da contabilidade adota geralmente esse esquema sem relacioná-lo a perspectiva do usuário dos dados contábeis. Contudo, a idéia fundamental de que estoques (líquidos de valor são compatíveis com a criação c distribuição de valor levanta uma questão básica no contexto de avalia4ao do patrimônio liquido: e possível delinear urna teoria coesiva do valor de uma firma sustentada pela relação de lucro limpo, no intuito de se identificar um papel claro para cada uma das três variáveis, quais sejam: o lucro, o valor contábil do patrimônio liquido e os dividendos?

Cathode Effects in Cylindrical Hall Thrusters

Energy Technology Data Exchange (ETDEWEB)

Granstedt, E.M.; Raitses, Y.; Fisch, N. J.

2008-09-12

Stable operation of a cylindrical Hall thruster (CHT) has been achieved using a hot wire cathode, which functions as a controllable electron emission source. It is shown that as the electron emission from the cathode increases with wire heating, the discharge current increases, the plasma plume angle reduces, and the ion energy distribution function shifts toward higher energies. The observed effect of cathode electron emission on thruster parameters extends and clarifies performance improvements previously obtained for the overrun discharge current regime of the same type of thruster, but using a hollow cathode-neutralizer. Once thruster discharge current saturates with wire heating, further filament heating does not affect other discharge parameters. The saturated values of thruster discharge parameters can be further enhanced by optimal placement of the cathode wire with respect to the magnetic field.

A one-dimensional model illustrating virtual-cathode formation in a novel coaxial virtual-cathode oscillator

International Nuclear Information System (INIS)

Turner, Geoffrey R.

2014-01-01

A one-dimensional electrostatic sheet model of a coaxial geometry Virtual Cathode Oscillator (VCO) is presented. The cathode is centrally located and connects to a peripherally located plate electrode to form a resonant cavity, and is thus considered to be a novel design. Charge is modelled as concentric sheets about the cathode whose absolute position and velocity are determined as a function of time by solving the relativistic equations of motion. The model predicts the formation of a virtual cathode between the grid and plate electrodes for the case of a space-charge limited current. Setting the electron reflexing frequency (as a function of the grid potential) comparable with the cavity resonant frequency is predicted to improve the efficiency of microwave emission

A Novel Cathode Material for Cathodic Dehalogenation of 1,1-Dibromo Cyclopropane Derivatives.

Science.gov (United States)

Gütz, Christoph; Selt, Maximilian; Bänziger, Markus; Bucher, Christoph; Römelt, Christina; Hecken, Nadine; Gallou, Fabrice; Galvão, Tomás R; Waldvogel, Siegfried R

2015-09-28

Leaded bronze turned out to be an excellent cathode material for the dehalogenation reaction of cyclopropanes without affecting the strained molecular entity. With this particular alloy, beneficial properties of lead cathodes are conserved, whereas the corrosion of cathode is efficiently suppressed. The solvent in the electrolyte determines whether a complete debromination reaction is achieved or if the process can be selectively stopped at the monobromo cyclopropane intermediate. The electroorganic conversion tolerates a variety of functional groups and can be conducted at rather complex substrates like cyclosporine A. This approach allows the sustainable preparation of cyclopropane derivatives. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Reflective article having a sacrificial cathodic layer

Science.gov (United States)

Kabagambe, Benjamin; Buchanan, Michael J.; Scott, Matthew S.; Rearick, Brian K.; Medwick, Paul A.; McCamy, James W.

2017-09-12

The present invention relates to reflective articles, such as solar mirrors, that include a sacrificial cathodic layer. The reflective article, more particularly includes a substrate, such as glass, having a multi-layered coating thereon that includes a lead-free sacrificial cathodic layer. The sacrificial cathodic layer includes at least one transition metal, such as a particulate transition metal, which can be in the form of flakes (e.g., zinc flakes). The sacrificial cathodic layer can include an inorganic matrix formed from one or more organo-titanates. Alternatively, the sacrificial cathodic layer can include an organic polymer matrix (e.g., a crosslinked organic polymer matrix formed from an organic polymer and an aminoplast crosslinking agent). The reflective article also includes an outer organic polymer coating, that can be electrodeposited over the sacrificial cathodic layer.

Geiger counters of gamma rays with a bismuth cathode; Compteurs de geiger a rayons gamma a cathode de bismuth

Energy Technology Data Exchange (ETDEWEB)

Meunier, R; Legrand, J P [Commissariat a l' Energie Atomique, Saclay(France). Centre d' Etudes Nucleaires

1953-07-01

Geiger Muller counters present a lake of efficiency of some per cent, for the {gamma} radiations. In the region 0,3 - 1 MeV, a substantial growth of their output can be obtained by a special construction of their cathode. In accordance with previous works, we constructed some counter of formed cathode by a pleated copper wire fencing covered of Bi by electrolysis. The successive modifications brought to a cylindrical conventional cathode in sheet metal of copper, that succeeds to this type of cathode, drive to an improvement of the output. (M.B.) [French] Les compteurs de Geiger Muller presentent une efficacite assez faible de l'ordre de quelques pour cent, pour les rayonnements {gamma}. Dans la region 0,3 - 1 MeV, un accroissement substantiel de leur rendement peut etre obtenu par une construction speciale de leur cathode. Conformement a des travaux anterieurs, nous avons construit des compteurs a cathode formee par un grillage de cuivre plisse recouvert de Bi par electrolyse. Les modifications successives apportees a une cathode conventionnelle cylindrique en tole de cuivre, qui aboutissent a ce type de cathode, conduisent a une amelioration du rendement. (M.B.)

Preservação do patrimônio arqueológico em terras indígenas

Directory of Open Access Journals (Sweden)

Erika Robrahn-González

2015-06-01

Full Text Available Este artigo apresenta o resultado do trabalho desenvolvido durante o “I Seminário Internacional de Gestão do Patrimônio Arqueológico Pan-Amazônico”, promovido em novembro/2007 pelo Instituto do Patrimônio Histórico e Artístico Nacional (IPHAN na cidade de Manaus/ AM, mais especificamente, na Sessão Temática intitulada “Preservação do Patrimônio Arqueológico em Terras Indígenas”.

An experimental study of molten salt electrorefining of uranium using solid iron cathode and liquid cadmium cathode for development of pyrometallurgical reprocessing

International Nuclear Information System (INIS)

Koyama, Tadafumi; Iizuka, Masatoshi; Tanaka, Hiroshi; Tokiwai, Moriyasu; Shoji, Yuichi; Fujita, Reiko; Kobayashi, Tsuguyuki.

1997-01-01

Electrorefining of uranium was studied for developing pyrometallurgical reprocessing technology of metal fuel cycle. After concentration dependence of polarization curve was measured, uranium was electrodeposited either on solid iron cathode or in liquid cadmium cathode. Design and operational conditions of the cathode were improved for obtaining much greater quantity of deposit, resulting in recovery of 732g of dendritic uranium on a single solid cathode, and of 232g of uranium in 2,344g of a liquid cadmium cathode. The behaviors of electro-codeposition of rare earth elements with uranium were observed for liquid cadmium cathode, and were found to follow the local equilibrium between salt electrolyte and cathode. The decontamination factors of FP simulating elements from uranium were tentatively determined as >2,000 for deposition to solid cathode and as >7 for deposition to liquid cadmium cathode, respectively. (author)

Monitoramento do percevejo marrom Euschistus heros (Hemiptera: Pentatomidae por feromônio sexual em lavoura de soja

Directory of Open Access Journals (Sweden)

Valvenarg Pereira da Silva

2014-11-01

Full Text Available O objetivo deste trabalho foi avaliar a eficiência das formulações septo de borracha e lure do feromônio sexual do percevejo marrom Euschistus heros e compará-la ao método do pano de batida, para o monitoramento dessa praga em lavoura de soja. Os tratamentos foram: feromônio em septo de borracha, feromônio em lure e amostragem com pano de batida. As amostragens foram realizadas semanalmente durante a fase reprodutiva da soja (dez semanas. Para estimar a densidade populacional de percevejos e compará-la à captura nas armadilhas de feromônio, foram efetuados quatro panos de batida por semana em todas as parcelas; além disso, foi determinado o número de percevejos capturados nas armadilhas por semana. Os danos provocados pelos percevejos nas sementes foram analisados pelo teste de tetrazólio. As formulações do feromônio foram eficientes na captura de E. heros, e a formulação em lure capturou mais percevejos. O controle precoce da população, indicado pelo nível de controle nas armadilhas com feromônio, resultou em sementes com maior qualidade do que as provenientes das parcelas monitoradas pelo pano de batida. Assim, as armadilhas com feromônio são mais eficientes que o pano de batida para o monitoramento das populações de percevejos durante a fase crítica do ataque deste inseto nas lavouras de soja.

ARTESANATO: ENTRE PATRIMÔNIO E MERCADO

Directory of Open Access Journals (Sweden)

Miriel Bilhalva Herrmann

2016-12-01

Full Text Available O presente trabalho busca estabelecer uma analise em relação a questão do artesanato, de como sofre modificações e interferências . Na qual no seu inicio tinha apenas valor utilitário, pois era produzido para suprir necessidades humanas. E com a revolução industrial foi relegada a marginalização, assim perdeu seu espaço para as máquinas. Mas logo com o intuito de criar identidades nacionais, começam as discussões em relação ao patrimônio. Dessa forma as concepções e ampliação sobre o seu conceito, propiciou grande valorização das diversidades culturais, assim como as técnicas artesanais. E a partir disso o artesanato passa a ser percebido como patrimônio, sendo visto e utilizado pelo turismo como fator de desenvolvimento econômico, dessa forma ocasionando um dilema entre estas técnicas artesanais de como se manter tradicionais, referência para a cultura e a identidade cultural. Ao mesmo tempo atender as necessidades do consumidor que se apresenta como turista, pois necessitam se adaptar para continuar sobrevivendo as mudanças do mercado

Cathode R and D for future light sources

Energy Technology Data Exchange (ETDEWEB)

Dowell, D.H., E-mail: dowell@slac.stanford.ed [SLAC National Accelerator Laboratory, 2575 Sand Hill Road, Menlo Park, CA 94025 (United States); Bazarov, I.; Dunham, B. [Cornell University, Cornell Laboratory for Accelerator-Based Sciences and Education (CLASSE) Wilson Laboratory, Cornell University, Ithaca, NY 14853 (United States); Harkay, K. [Argonne National Laboratory, 9700 S. Cass Avenue, Argonne, Il 60439 (United States); Hernandez-Garcia, C. [Thomas Jefferson Laboratory, 12000 Jefferson Ave, Free Electron Laser Suite 19 Newport News, VA 23606 (United States); Legg, R. [University of Wisconsin, SRC, 3731 Schneider Dr., Stoughton, WI 53589 (United States); Padmore, H. [Lawrence Berkeley National Laboratory, 1 Cyclotron Rd, Berkeley, CA 94720 (United States); Rao, T.; Smedley, J. [Brookhaven National Laboratory, 20 Technology Street, Bldg. 535B, Brookhaven National Laboratory Upton, NY 11973 (United States); Wan, W. [Lawrence Berkeley National Laboratory, 1 Cyclotron Rd, Berkeley, CA 94720 (United States)

2010-10-21

This paper reviews the requirements and current status of cathodes for accelerator applications, and proposes a research and development plan for advancing cathode technology. Accelerator cathodes need to have long operational lifetimes and produce electron beams with a very low emittance. The two principal emission processes to be considered are thermionic and photoemission with the photocathodes being further subdivided into metal and semi-conductors. Field emission cathodes are not included in this analysis. The thermal emittance is derived and the formulas used to compare the various cathode materials. To date, there is no cathode which provides all the requirements needed for the proposed future light sources. Therefore a three part research plan is described to develop cathodes for these future light source applications.

Emission mechanism in high current hollow cathode arcs

International Nuclear Information System (INIS)

Krishnan, M.

1976-01-01

Large (2 cm-diameter) hollow cathodes have been operated in a magnetoplasmadynamic (MPD) arc over wide ranges of current (0.25 to 17 kA) and mass flow (10 -3 to 8 g/sec), with orifice current densities and mass fluxes encompassing those encountered in low current steady-state hollow cathode arcs. Detailed cathode interior measurements of current and potential distributions show that maximum current penetration into the cathode is about one diameter axially upstream from the tip, with peak inner surface current attachment up to one cathode diameter upstream of the tip. The spontaneous attachment of peak current upstream of the cathode tip is suggested as a criterion for characteristic hollow cathode operation. This empirical criterion is verified by experiment

Beryllium electrodeposition on aluminium cathode from chloride melts

International Nuclear Information System (INIS)

Nichkov, I.F.; Novikov, E.A.; Serebryakov, G.A.; Kanashin, Yu.P.; Sardyko, G.N.

1980-01-01

Cathodic processes during beryllium deposition on liquid and solid aluminium cathodes are investigated. Mixture of sodium, potassium and beryllium chloride melts served as an lectrolyte. Beryllium ion discharge at the expense of alloy formation takes place at more positive potentials than on an indifferent cathode at low current densities ( in the case of liquid aluminium cathode). Metallographic analysis and measurements of microhardness have shown, that the cathodic product includes two phases: beryllium solid solution in aluminium and metallic beryllium. It is concluded, that aluminium-beryllium alloys with high cathodic yield by current can be obtained by the electrolytic method

High temperature deformation of polycrystalline NiO and CoO

International Nuclear Information System (INIS)

Krishnamachari, V.; Notis, M.R.

1977-01-01

High temperature creep of polycrystalline NiO appears to be controlled by oxygen lattice diffusion at temperatures between 1273 and 1373 K and at stress levels from 34.5 to 79.8 MPa (5 to 11 ksi). Experimentally observed creep rates agree well with predictions obtained from deformation maps based on self-diffusion data. TEM examination indicates that dislocations present in crept NiO specimens are predominantly glide-type rather than climb-type dislocations as found in CoO. The difference in creep behavior of these materials is believed to be due to the difference in stacking fault energies and the nature of charge associated with lattice defects. 2 tables. 7 figs., 34 references

The effect of anion on the magnetic properties of nanocrystalline NiO synthesized by homogeneous precipitation

International Nuclear Information System (INIS)

Ranga Rao Pulimi, V.; Jeevanandam, P.

2009-01-01

The effect of using different anions (nitrate, chloride, sulfate, and acetate) during the precursor synthesis, by homogeneous precipitation, on the magnetic properties of the final product (nanocrystalline NiO), has been studied. The precursors and the oxide were characterized by various analytical techniques including powder X-ray diffraction, FT-IR spectroscopy, thermal gravimetry (TGA), and magnetic measurements. The synthesized NiO samples possess crystallite size in the range, ∼2-6 nm, depending on the anion of the nickel salt. The nickel oxide nanoparticles exhibit superparamagnetic behavior. Acetate and sulfate anions lead to NiO with higher saturation magnetization (∼1.2-1.8 emu/g), while chloride and nitrate anions lead to NiO nanoparticles with lower saturation magnetization (∼0.1-0.4 emu/g) values. The observed magnetic behavior has been attributed to the size effect.

The effect of anion on the magnetic properties of nanocrystalline NiO synthesized by homogeneous precipitation

Energy Technology Data Exchange (ETDEWEB)

Ranga Rao Pulimi, V. [Department of Chemistry, Indian Institute of Technology Roorkee, Roorkee 247667 (India); Jeevanandam, P. [Department of Chemistry, Indian Institute of Technology Roorkee, Roorkee 247667 (India)], E-mail: jeevafcy@iitr.ernet.in

2009-09-15

The effect of using different anions (nitrate, chloride, sulfate, and acetate) during the precursor synthesis, by homogeneous precipitation, on the magnetic properties of the final product (nanocrystalline NiO), has been studied. The precursors and the oxide were characterized by various analytical techniques including powder X-ray diffraction, FT-IR spectroscopy, thermal gravimetry (TGA), and magnetic measurements. The synthesized NiO samples possess crystallite size in the range, {approx}2-6 nm, depending on the anion of the nickel salt. The nickel oxide nanoparticles exhibit superparamagnetic behavior. Acetate and sulfate anions lead to NiO with higher saturation magnetization ({approx}1.2-1.8 emu/g), while chloride and nitrate anions lead to NiO nanoparticles with lower saturation magnetization ({approx}0.1-0.4 emu/g) values. The observed magnetic behavior has been attributed to the size effect.

Effect of Precursor Concentration on Structural Optical and Electrical Properties of NiO Thin Films Prepared by Spray Pyrolysis

Directory of Open Access Journals (Sweden)

Rafia Barir

2017-01-01

Full Text Available Undoped nickel oxide (NiO thin films were deposited on 500°C heated glass substrates using spray pyrolysis method at (0.015–0.1 M range of precursor. The latter was obtained by decomposition of nickel nitrate hexahydrate in double distilled water. Effect of precursor concentration on structural, optical, and electrical properties of NiO thin films was investigated. X-ray diffraction (XRD shows the formation of NiO under cubic structure with single diffraction peak along (111 plane at 2θ=37.24°. When precursor concentration reaches 0.1 M, an increment in NiO crystallite size over 37.04 nm was obtained indicating the product nano structure. SEM images reveal that beyond 0.04 M as precursor concentration the substrate becomes completely covered with NiO and thin films exhibit formation of nano agglomerations at the top of the sample surface. Ni-O bonds vibrations modes in the product of films were confirmed by FT-IR analysis. Transparency of the films ranged from 57 to 88% and band gap energy of the films decreases from 3.68 to 3.60 eV with increasing precursor concentration. Electrical properties of the elaborated NiO thin films were correlated to the precursor concentration.

Emission ability of La-Sc-Mo cathode

International Nuclear Information System (INIS)

Yang Jiancan; Nie Zuoren; Xi Xiaoli; Wang Yiman

2004-01-01

In this paper La-Sc-Mo cathode has been prepared and its electron emission ability was measured. This type of cathode shows good electron emission performance that the saturated current density is 6.74 A cm -1 and the work function is about 2.59 eV at 1300 deg. C, which is much lower than thoriated tungsten cathode (Th-W). So it is a potential cathode to replace the Th-W cathode with radioactive pollution. Surface analysis shows that good emission ability due to the 20 nm surplus La layer and the element Sc may do good to the La diffusion to the surface

DARHT 2 kA Cathode Development

Energy Technology Data Exchange (ETDEWEB)

Henestroza, E.; Houck, T.; Kwan, J.W.; Leitner, M.; Miram, G.; Prichard, B.; Roy, P.K.; Waldron, W.; Westenskow, G.; Yu, S.; Bieniosek, F.M.

2009-03-09

In the campaign to achieve 2 kA of electron beam current, we have made several changes to the DARHT-II injector during 2006-2007. These changes resulted in a significant increase in the beam current, achieving the 2 kA milestone. Until recently (before 2007), the maximum beam current that was produced from the 6.5-inch diameter (612M) cathode was about 1300 A when the cathode was operating at a maximum temperature of 1140 C. At this temperature level, the heat loss was dominated by radiation which is proportional to temperature to the fourth power. The maximum operating temperature was limited by the damage threshold of the potted filament and the capacity of the filament heater power supply, as well as the shortening of the cathode life time. There were also signs of overheating at other components in the cathode assembly. Thus it was clear that our approach to increase beam current could not be simply trying to run at a higher temperature and the preferred way was to operate with a cathode that has a lower work function. The dispenser cathode initially used was the type 612M made by SpectraMat. According to the manufacturer's bulletin, this cathode should be able to produce more than 10 A/cm{sup 2} of current density (corresponding to 2 kA of total beam current) at our operating conditions. Instead the measured emission (space charge limited) was 6 A/cm{sup 2}. The result was similar even after we had revised the activation and handling procedures to adhere more closely to the recommend steps (taking longer time and nonstop to do the out-gassing). Vacuum was a major concern in considering the cathode's performance. Although the vacuum gauges at the injector vessel indicated 10{sup -8} Torr, the actual vacuum condition near the cathode in the central region of the vessel, where there might be significant out-gassing from the heater region, was never determined. Poor vacuum at the surface of the cathode degraded the emission (by raising the work function

DARHT 2 kA Cathode Development

International Nuclear Information System (INIS)

Henestroza, E.; Houck, T.; Kwan, J.W.; Leitner, M.; Miram, G.; Prichard, B.; Roy, P.K.; Waldron, W.; Westenskow, G.; Yu, S.; Bieniosek, F.M.

2009-01-01

In the campaign to achieve 2 kA of electron beam current, we have made several changes to the DARHT-II injector during 2006-2007. These changes resulted in a significant increase in the beam current, achieving the 2 kA milestone. Until recently (before 2007), the maximum beam current that was produced from the 6.5-inch diameter (612M) cathode was about 1300 A when the cathode was operating at a maximum temperature of 1140 C. At this temperature level, the heat loss was dominated by radiation which is proportional to temperature to the fourth power. The maximum operating temperature was limited by the damage threshold of the potted filament and the capacity of the filament heater power supply, as well as the shortening of the cathode life time. There were also signs of overheating at other components in the cathode assembly. Thus it was clear that our approach to increase beam current could not be simply trying to run at a higher temperature and the preferred way was to operate with a cathode that has a lower work function. The dispenser cathode initially used was the type 612M made by SpectraMat. According to the manufacturer's bulletin, this cathode should be able to produce more than 10 A/cm 2 of current density (corresponding to 2 kA of total beam current) at our operating conditions. Instead the measured emission (space charge limited) was 6 A/cm 2 . The result was similar even after we had revised the activation and handling procedures to adhere more closely to the recommend steps (taking longer time and nonstop to do the out-gassing). Vacuum was a major concern in considering the cathode's performance. Although the vacuum gauges at the injector vessel indicated 10 -8 Torr, the actual vacuum condition near the cathode in the central region of the vessel, where there might be significant out-gassing from the heater region, was never determined. Poor vacuum at the surface of the cathode degraded the emission (by raising the work function value). We reexamined

Low-energy charge transfer excitations in NiO

International Nuclear Information System (INIS)

Sokolov, V I; Yermakov, A Ye; Uimin, M A; Gruzdev, N B; Pustovarov, V A; Churmanov, V N; Ivanov, V Yu; Sokolov, P S; Baranov, A N; Moskvin, A S

2012-01-01

Comparative analysis of photoluminescence (PL) and photoluminescence excitation (PLE) spectra of NiO poly- and nanocrystals in the spectral range 2-5.5 eV reveals two PLE bands peaked near 3.7 and 4.6 eV with a dramatic rise in the low-temperature PLE spectral weight of the 3.7 eV PLE band in the nanocrystalline NiO as compared with its polycrystalline counterpart. In frames of a cluster model approach we assign the 3.7 eV PLE band to the low-energy bulk-forbidden p-d (t 1g (π)-e g ) charge transfer (CT) transition which becomes the allowed one in the nanocrystalline state while the 4.6 eV PLE band is related to a bulk allowed d-d (e g -e g ) CT transition scarcely susceptible to the nanocrystallization. The PLE spectroscopy of the nanocrystalline materials appears to be a novel informative technique for inspection of different CT transitions.

Rechargeable lithium/polymer cathode batteries

Science.gov (United States)

Osaka, Tetsuya; Nakajima, Toshiki; Shiota, Koh; Owens, Boone B.

1989-06-01

Polypyrrole (PPy) and polyaniline (PAn) were investigated for cathode materials of rechargeable lithium batteries. PPy films prepared with PF6(-) anion and/or platinum substrate precoated with nitrile butadiene rubber (NBR) were excellent cathode materials because of rough and/or highly oriented film structure. PAn films were successfully prepared from non-aqueous propylene carbonate solution containing aniline, CF3COOH and lithium perchlorate. Its acidity strongly affects the anion doping-undoping behavior. The PAn cathode prepared in high acidic solution (e.g., 4:1 ratio of acid:aniline) gives the excellent battery performance.

A Influência do Patrocínio Esportivo na Atitude sobre Marcas

OpenAIRE

Carlos Eugênio Zardini Filho

2017-01-01

Segundo Mason (2005), o patrocínio esportivo se caracteriza por aumentar a frequência de exposição das mensagens de marketing e tem grande impacto sobre a atitude do consumidor. Este projeto tem como objetivo identificar se o patrocínio esportivo é capaz de modificar favoravelmente o aspecto afetivo da atitude em relação a uma marca, mesmo a partir de um cenário negativo sobre tal marca. Quanto ao método, utilizou-se um mode...

Hydrothermal synthesis of p-type nanocrystalline NiO nanoplates for high response and low concentration hydrogen gas sensor application

KAUST Repository

Nakate, Umesh T.; Lee, Gun Hee; Ahmad, Rafiq; Patil, Pramila; Bhopate, Dhanaji P.; Hahn, Y.B.; Yu, Y.T.; Suh, Eun-kyung

2018-01-01

High quality nanocrystalline NiO nanoplates were synthesized using surfactant and template free hydrothermal route. The gas sensing properties of NiO nanoplates were investigated. The nanoplates morphology of NiO with average thickness ~20 nm and diameter ~100 nm has been confirmed by FE-SEM and TEM. Crystalline quality of NiO has been studied using HRTEM and SAED techniques. Structural properties and elemental compositions have been analysed by XRD and energy dispersive spectrometer (EDS) respectively. The detailed investigation of structural parameters has been carried out. The optical properties of NiO were analyzed from UV-Visible and photoluminescence spectra. NiO nanoplates have good selectivity towards hydrogen (H2) gas. The lowest H2 response of 3% was observed at 2 ppm, whereas 90% response was noted for 100 ppm at optimized temperature of 200 °C with response time 180 s. The H2 responses as functions of different operating temperature as well as gas concentrations have been studied along with sensor stability. The hydrogen sensing mechanism was also elucidated.

Hydrothermal synthesis of p-type nanocrystalline NiO nanoplates for high response and low concentration hydrogen gas sensor application

KAUST Repository

Nakate, Umesh T.

2018-05-30

High quality nanocrystalline NiO nanoplates were synthesized using surfactant and template free hydrothermal route. The gas sensing properties of NiO nanoplates were investigated. The nanoplates morphology of NiO with average thickness ~20 nm and diameter ~100 nm has been confirmed by FE-SEM and TEM. Crystalline quality of NiO has been studied using HRTEM and SAED techniques. Structural properties and elemental compositions have been analysed by XRD and energy dispersive spectrometer (EDS) respectively. The detailed investigation of structural parameters has been carried out. The optical properties of NiO were analyzed from UV-Visible and photoluminescence spectra. NiO nanoplates have good selectivity towards hydrogen (H2) gas. The lowest H2 response of 3% was observed at 2 ppm, whereas 90% response was noted for 100 ppm at optimized temperature of 200 °C with response time 180 s. The H2 responses as functions of different operating temperature as well as gas concentrations have been studied along with sensor stability. The hydrogen sensing mechanism was also elucidated.

Electron beam generation form a superemissive cathode

International Nuclear Information System (INIS)

Hsu, T.-Y.; Liou, R.-L.; Kirkman-Amemiya, G.; Gundersen, M.A.

1991-01-01

An experimental study of electron beams produced by a superemissive cathode in the Back-Lighted Thyratron (BLT) and the pseudospark is presented. This work is motivated by experiments demonstrating very high current densities (≥10 kA/cm 2 over an area of 1 cm 2 ) from the pseudospark and BLT cathode. This high-density current is produced by field-enhanced thermionic emission from the ion beam-heated surface of a molybdenum cathode. This work reports the use of this cathode as a beam source, and is to be distinguished from previous work reporting hollow cathode-produced electron beams. An electron beam of more than 260 A Peak current has been produced with 15 kV applied voltage. An efficiency of ∼10% is estimated. These experimental results encourage further investigation of the super-emissive cathode as an intense electron beam source for applications including accelerator technology

TiO2-B Nanoribbons Anchored with NiO Nanosheets as Hybrid Anode Materials for Rechargeable Lithium ion Batteries

DEFF Research Database (Denmark)

Zhang, J. Y.; Shen, J.X.; Wang, T.L.

2015-01-01

A new type of TiO2-B nanoribbon anchored with NiO nanosheets (TiO2@NiO) is synthesized via a hydrothermal process and a subsequent homogeneous precipitation method. XRD analysis indicates that TiO2-B and cubic NiO phases exist in the composites. According to SEM images, the morphology of the TiO2...

Effect of NiO growth conditions on the bipolar resistance memory switching of Pt/NiO/SRO structure

International Nuclear Information System (INIS)

Kurnia, F.; Hadiyawarman, H.; Jung, C. U.; Liu, C. L.; Lee, S. B.; Yang, S. M.; Park, H. W.; Song, S. J.; Hwang, C. S.

2010-01-01

We deposited NiO thin films with SrRuO 3 bottom electrodes on SrTiO 3 (001) substrates by using pulsed laser deposition. The growth temperature and the oxygen pressure were varied in order to obtain NiO films with different structural and electrical properties. We investigated the I-V characteristics of the Pt/NiO/SRO structures and observed a strong dependence of bipolar resistance switching on the growth conditions of the NiO thin films. Stable bipolar memory resistance switching was observed only in the devices with NiO films deposited at 400 .deg. C and 10 mTorr of O 2 . The off-state I-V curve of bipolar switching showed a linear fitting to the Schottky effect, indicating its origin in the NiO/SRO interface. Our results suggest that the growth conditions of NiO may affect the bipolar switching behavior through the film's resistance, the film's crystallinity, or the status of the grain boundaries.

Electrodeposition of uranium in stirred liquid cadmium cathode

International Nuclear Information System (INIS)

Koyama, T.; Tanaka, H.

1997-01-01

The electrodeposition of U in a liquid Cd cathode was known to be hampered by the formation of dendritic U on the Cd surface. Electrotransports of uranium to the stirred liquid Cd cathode were carried out at 773 K for different cathode current densities and different Reynolds number of stirring. The maximum amount of U taken in the liquid Cd cathode without forming dendrites was found to increase with an increasing Reynolds number of stirring and decrease with increasing cathode current density. (orig.)

Growth mechanism and magnon excitation in NiO nanowalls

Directory of Open Access Journals (Sweden)

Yang Chun

2011-01-01

Full Text Available Abstract The nanosized effects of short-range multimagnon excitation behavior and short-circuit diffusion in NiO nanowalls synthesized using the Ni grid thermal treatment method were observed. The energy dispersive spectroscopy mapping technique was used to characterize the growth mechanism, and confocal Raman scattering was used to probe the antiferromagnetic exchange energy J 2 between next-nearest-neighboring Ni ions in NiO nanowalls at various growth temperatures below the Neel temperature. This study shows that short spin correlation leads to an exponential dependence of the growth temperatures and the existence of nickel vacancies during the magnon excitation. Four-magnon configurations were determined from the scattering factor, revealing a lowest state and monotonic change with the growth temperature. PACS: 75.47.Lx; 61.82.Rx; 75.50.Tt; 74.25.nd; 72.10.Di

Growth mechanism and magnon excitation in NiO nanowalls

Science.gov (United States)

2011-01-01

The nanosized effects of short-range multimagnon excitation behavior and short-circuit diffusion in NiO nanowalls synthesized using the Ni grid thermal treatment method were observed. The energy dispersive spectroscopy mapping technique was used to characterize the growth mechanism, and confocal Raman scattering was used to probe the antiferromagnetic exchange energy J2 between next-nearest-neighboring Ni ions in NiO nanowalls at various growth temperatures below the Neel temperature. This study shows that short spin correlation leads to an exponential dependence of the growth temperatures and the existence of nickel vacancies during the magnon excitation. Four-magnon configurations were determined from the scattering factor, revealing a lowest state and monotonic change with the growth temperature. PACS: 75.47.Lx; 61.82.Rx; 75.50.Tt; 74.25.nd; 72.10.Di PMID:21824408

A one-dimensional model illustrating virtual-cathode formation in a novel coaxial virtual-cathode oscillator.

CSIR Research Space (South Africa)

Turner, GR

2014-09-01

Full Text Available A one-dimensional electrostatic sheet model of a coaxial geometry Virtual Cathode Oscillator (VCO) is presented. The cathode is centrally located and connects to a peripherally located plate electrode to form a resonant cavity, and is thus...

Tropical cyclones over NIO during La-Nina Modoki years

Digital Repository Service at National Institute of Oceanography (India)

Sumesh, K.G.; RameshKumar, M.R.

Tropical cyclones over NIO (North Indian Ocean) are highly influenced by the El-Nino and La-Nina activities over the Pacific Ocean Influences of air-sea interaction processes like El-Nino Modoki and La-Nina Modoki on tropical cyclones are less...

Explosive-emission cathode fabricated from superconducting cable

International Nuclear Information System (INIS)

Vavra, I.; Korenev, S.A.

1989-01-01

The authors describe on explosive-emission cathode that is based on stock superconducting cable - type NT-50, for example - that is bunched and held in a copper matrix. The copper matrix is partially etched away to create a multipoint structure for the cathode-plasma initiators. With 100-300 kV on the diode and a distance of 1 cm between the anode and cathode, electron currents of 20-80 and 60-300 A are obtained with cathode diameters of 0.5 and 1 cm, respectively

Hollow cathode for positive ion sources

International Nuclear Information System (INIS)

Schechter, D.E.; Kim, J.; Tsai, C.C.

1979-01-01

Development to incorporate hollow cathodes into high power ion sources for neutral beam injection systems is being pursued. Hollow tube LaB 6 -type cathodes, similar to a UCLA design, have been constructed and tested in several ORNL ion source configurations. Results of testing include arc discharge parameters of >1000 and 500 amps for 0.5 and 10 second pulse lengths, respectively. Details of cathode construction and additional performance results are discussed

Explosive-emission cathode fabricated using track method

International Nuclear Information System (INIS)

Akap'ev, G.N.; Korenev, S.A.

1989-01-01

Fabrication technique for large area multipoint cathodes is described. The technique is based on channels filling with metal in the ion-irradiated dielectric film producted after channel etching. It is shown, that cathode may be used under explosive emission conditions. Characteristics of diode with the mentioned type cathodes are measured

Plasma Deposition of Oxide-Coated Cathodes

National Research Council Canada - National Science Library

Umstattd, Ryan

1998-01-01

...; such cathodes may also have applicability for lower current density continuous wave devices. This novel approach to manufacturing an oxide cathode eliminates the binders that may subsequently (and unpredictably...

Cathode plasma expansion in diode with explosive emission

International Nuclear Information System (INIS)

Zuo Yinghong; Fan Ruyu; Wang Jianguo; Zhu Jinhui

2012-01-01

The evolution characteristics of the cathode plasma in a planar diode with explosive emission were analyzed. Be- sides the axial expansion which can reduce the effective anode-cathode gap, the radial expansion of the cathode plasma which can affect the effective emitting area was also taken into account. According to the Child-Langmuir law and the experimental data of current and voltage with a electron vacuum diode under four-pulse mode, the dynamics of the cathode plasma was investigated, on the assumption that the radial speeds of the cathode plasma was approximately equal to the axial speed. The results show that the radial and axial expansion speeds of the cathode plasma are 0.9-2.8 cm/μs. (authors)

Cathodic corrosion: Part 2. Properties of nanoparticles synthesized by cathodic corrosion

International Nuclear Information System (INIS)

Yanson, A.I.; Yanson, Yu.I.

2013-01-01

We demonstrate how cathodic corrosion in concentrated aqueous solutions enables one to prepare nanoparticles of various metals and metal alloys. Using various characterization methods we show that the composition of nanoparticles remains that of the starting material, and the resulting size distribution remains rather narrow. For the case of platinum we show how the size and possibly even the shape of the nanoparticles can be easily controlled by the parameters of corrosion. Finally, we discuss the advantages of using the nanoparticles prepared by cathodic corrosion for applications in (electro-)catalysis.

Ab inito calculations of Hubbard parameters for NiO and Gd crystals

Directory of Open Access Journals (Sweden)

A. R Faghihi and S Jalali Asadabadi

2008-07-01

Full Text Available   In this research the Hubbard parameters have been calculated for NiO and Gd crystals, as two strongly correlated systems with partially full 3d and 4f levels, respectively. The calculations were performed within the density functional theory (DFT using the augmented plane waves plus the local orbitat (APW+lo method. We constructed a suitable supercell and found that the Hubbard parameters for the NiO and Gd compounds are equal to 5.9 eV and 5.7 eV, respectively. Our results are in good agreement with experimental data and results of other computational methods. Then we used the obtained parameters to study the structural properties of NiO and Gd by means of LDA+U approximation. Our results calculated by the LDA+U method which are in better agreement with the experiment show a significant improvement compared to the GGA approximation. The result shows that our method for calculating U parameter can be considered as a satisfactory method to study a strongly correlated system.

Surface-spin magnetism of antiferromagnetic NiO in nanoparticle and bulk morphology

International Nuclear Information System (INIS)

Jagodic, M; Jaglicic, Z; Jelen, A; Dolinsek, J; Lee, Jin Bae; Kim, Hae Jin; Kim, Young-Min

2009-01-01

The surface-spin magnetism of the antiferromagnetic (AFM) material NiO in nanoparticle and bulk morphology was investigated by magnetic measurements (temperature-dependent zero-field-cooled (zfc) and field-cooled (fc) dc susceptibility, ac susceptibility and zfc and fc hysteresis loops). We addressed the question of whether the multisublattice ordering of the uncompensated surface spins and the exchange bias (EB) effect are only present in the nanoparticles, originating from their high surface-to-volume ratio or if these surface phenomena are generally present in the AFM materials regardless of their bulky or nanoparticle morphology, but the effect is just too small to be detected experimentally in the bulk due to a very small surface magnetization. Performing experiments on the NiO nanoparticles of different sizes and bulk NiO grains, we show that coercivity enhancement and hysteresis loop shift in the fc experiments, considered to be the key experimental manifestations of multisublattice ordering and the EB effect, are true nanoscale phenomena only present in the nanoparticles and absent in the bulk.

High-quality single crystalline NiO with twin phases grown on sapphire substrate by metalorganic vapor phase epitaxy

Directory of Open Access Journals (Sweden)

Kazuo Uchida

2012-12-01

Full Text Available High-quality single crystalline twin phase NiO grown on sapphire substrates by metalorganic vapor phase epitaxy is reported. X-ray rocking curve analysis of NiO films grown at different temperatures indicates a minimum full width at half maximum of the cubic (111 diffraction peak of 0.107° for NiO film grown at as low as 550 °C. Detailed microstructural analysis by Φ scan X-ray diffraction and transmission electron microscopy reveal that the NiO film consists of large single crystalline domains with two different crystallographic orientations which are rotated relative to each other along the [111] axis by 60°. These single crystal domains are divided by the twin phase boundaries.

Cathodic disbonding of organic coatings on submerged steel

Energy Technology Data Exchange (ETDEWEB)

Knudsen, Ole oeystein

1998-12-31

In offshore oil production, submerged steel structures are commonly protected by an organic coating in combination with cathodic protection. The main advantage is that the coating decreases the current demand for cathodic protection. But the coating degrades with time. This thesis studies one of the most important mechanisms for coating degradation in seawater, cathodic disbonding. Seven commercial coatings and two model coatings with various pigmentations have been studied. Parameter studies, microscopy and studies of free films were used in the mechanism investigations. Exposure to simulated North Sea conditions was used in the performance studies. The effect of aluminium and glass barrier pigments on cathodic disbonding was investigated. The mechanism for the effect of the aluminium pigments on cathodic disbonding was also investigated. The transport of charge and oxygen to the steel/coating interface during cathodic disbonding was studied for two epoxy coatings. Cathodic disbonding, blistering and current demand for cathodic protection was measured for nine commercial coatings for submerged steel structures, using the ASTM-G8 standard test and a long term test under simulated North Sea conditions. The relevance of the ASTM-G8 test as a prequalification test was evaluated. 171 refs., 40 figs., 6 tabs.

Performance evaluation and parametric optimum design of a molten carbonate fuel cell-thermophotovoltaic cell hybrid system

International Nuclear Information System (INIS)

Yang, Zhimin; Liao, Tianjun; Zhou, Yinghui; Lin, Guoxing; Chen, Jincan

2016-01-01

Highlights: • A molten carbonate fuel cell-thermophotovoltaic cell hybrid system is established. • The performance characteristics of the hybrid system are systematically evaluated. • The optimal regions of the power output density and efficiency are determined. • The values of key parameters at the maximum power output density are calculated. • The proposed system is proved to have advantages over other hybrid systems. - Abstract: A new model of the hybrid system composed of a molten carbonate fuel cell (MCFC) and a thermophotovoltaic cell (TPVC) is proposed to recovery the waste heat produced by the MCFC. Expressions for the power output and the efficiency of the hybrid system are analytically derived. The performance characteristics of the hybrid system are evaluated. It is found that when the current density of the MCFC, voltage output of the TPVC, electrode area ratio of the MCFC to the TPVC, and energy gap of the material in the photovoltaic cell are optimally chosen, the maximum power output density of the hybrid system is obviously larger than that of the single MCFC. Moreover, the improved percentages of the maximum power output density of the proposed model relative to that of the single MCFC are calculated for differently operating temperatures of the MCFC and are compared with those of some MCFC-based hybrid systems reported in the literature, and consequently, the advantages of the MCFC-TPVC hybrid system are revealed.

Design Of Photovoltaic Powered Cathodic Protection System

Directory of Open Access Journals (Sweden)

Golina Samir Adly

2017-07-01

Full Text Available The corrosion caused by chemical reaction between metallic structures and surrounding mediums such as soil or water .the CP cathodic protection system is used to protect metallic structure against corrosion. Cathodic protection CP used to minimize corrosion by utilizing an external source of electrical current which forces the entire structure to become a cathode. There are two Types of cathodic protection system Galvanic current Impressed current.the Galvanic current is called a sacrificial anode is connected to the protected structure cathode through a DC power supply. In Galvanic current system a current passes from the sacrificing anode to the protected structure .the sacrificial anode is corroded rather than causing the protected structure corrosion .protected structure requires a constant current to stop the corrosion which determined by area structure metal and the surrounding medium. The rains humidity are decrease soil resistivity and increase the DC current .The corrosion and over protection resulting from increase in the DC current is harmful for the metallic structure. This problem can be solved by conventional cathodic protection system by manual adjustment of DC voltage periodically to obtain a constant current .the manual adjustment of DC voltage depends on experience of the technician and using the accuracy of the measuring equipment. The errors of measuring current depend on error from the technician or error from the measuring equipment. the corrosion of structure may occur when the interval between two successive adjustment is long .An automatically regulated cathodic protection system is used to overcome problems from conventional cathodic protection system .the regulated cathodic protection system adjust the DC voltage of the system automatically when it senses the variations of surrounding medium resistivity so the DC current is constant at the required level.

Cold cathodes on ultra-dispersed diamond base

International Nuclear Information System (INIS)

Alimova, A.N.; Zhirnov, V.V.; Chubun, N.N.; Belobrov, P.I.

1998-01-01

Prospects of application of nano diamond powders for fabrication of cold cathodes are discussed.Cold cathodes based on silicon pointed structures with nano diamond coatings were prepared.The deposition technique of diamond coating was dielectrophoresis from suspension of nano diamond powder in organic liquids.The cathodes were tested in sealed prototypes of vacuum electronic devices

Preparation of p-type NiO films by reactive sputtering and their application to CdTe solar cells

Science.gov (United States)

Ishikawa, Ryousuke; Furuya, Yasuaki; Araki, Ryouichi; Nomoto, Takahiro; Ogawa, Yohei; Hosono, Aikyo; Okamoto, Tamotsu; Tsuboi, Nozomu

2016-02-01

Transparent p-type NiO films were prepared by reactive sputtering using the facing-target system under Ar-diluted O2 gas at Tsub of 30 and 200 °C. The increasing intensity of dominant X-ray diffraction (XRD) peaks indicates improvements in the crystallinity of NiO films upon Cu doping. In spite of the crystallographic and optical changes after Cu-doping, the electrical properties of Cu-doped NiO films were slightly improved. Upon Ag-doping at 30 °C under low O2 concentration, on the other hand, the intensity of the dominant (111) XRD peaks was suppressed and p-type conductivity increased from ˜10-3 to ˜10-1 S cm-1. Finally, our Ag-doped NiO films were applied as the back contact of CdTe solar cells. CdTe solar cells with a glass/ITO/CdS/CdTe/NiO structure exhibited an efficiency of 6.4%, suggesting the high potential of using p-type NiO for the back-contact film in thin-film solar cells.

A Influência do Patrocínio Esportivo na Atitude sobre Marcas

Directory of Open Access Journals (Sweden)

Carlos Eugênio Zardini Filho

2017-06-01

Full Text Available Segundo Mason (2005, o patrocínio esportivo se caracteriza por aumentar a frequência de exposição das mensagens de marketing e tem grande impacto sobre a atitude do consumidor. Este projeto tem como objetivo identificar se o patrocínio esportivo é capaz de modificar favoravelmente o aspecto afetivo da atitude em relação a uma marca, mesmo a partir de um cenário negativo sobre tal marca. Quanto ao método, utilizou-se um modelo experimental, medidas repetidas, com aplicação de questionário onde os participantes avaliavam, em escalas, afirmações após inserção de diferentes cenários relacionados a ações de patrocínio esportivo. Considerando as análises descritivas e estatísticas realizadas, em suma, o experimento proposto permitiu o entendimento de que o patrocínio esportivo é capaz de alterar positivamente a atitude de consumidores. Além disso, os resultados demonstram que estratégias macros de marketing esportivo são mais eficazes do que ações específicas para tal mudança. Desta maneira, observa-se que um planejamento de comunicação, integrando o futebol e outros esportes olímpicos, está propenso a criar um ambiente ideal para que os sentimentos positivos vinculados a natureza do esporte possam transpor a barreira de cenários negativos e ocasionar em atitudes favoráveis perante uma determinada empresa/marca.  

Preliminary results on the chemical characterisation of the cathode nickel--emissive layer interface in oxide cathodes

International Nuclear Information System (INIS)

Jenkins, S.N.; Barber, D.K.; Whiting, M.J.; Baker, M.A.

2003-01-01

In cathode ray tube (CRT) thermionic oxide cathodes, the nickel-oxide interface properties are key to understanding the mechanisms of operation. At the elevated operational temperatures, free barium is formed at the interface by the reaction of reducing activators, from the nickel alloy, with barium oxide. The free barium diffuses to the outer surface of the oxide providing a low work function electron-emitting surface. However, during cathode life an interface layer grows between the nickel alloy and oxide, comprised of reaction products. The interfacial layer sets limits on the cathode performance and useful operational lifetime by inhibiting the barium reducing reaction. This paper discusses sample preparation procedures for exposure of the interface and the use of several surface and bulk analytical techniques to study interface layer formation. SEM, AES and SIMS data are presented, which provide preliminary insight into the mechanisms operating during the cathode's lifetime. There is evidence that the activator elements in the nickel alloy base, Al and Mg, are able to diffuse to the surface of the oxide during activation and ageing and that these elements are enriched at the interface after accelerated life

AB/sub 5/-catalyzed hydrogen evolution cathodes

Energy Technology Data Exchange (ETDEWEB)

Hall, D E; Sawada, T; Shepard, V R; Tsujikawa, Y

1984-01-01

The AB/sub 5/ metal compounds are highly efficient hydrogen evolution electrocatalysts in alkaline electrolyte. Three types of AB/sub 5/-catalyzed cathode structures were made, using the hydride-forming AB/sub 5/ compounds in particulate form. Plastic-bonded cathodes containing >90 w/o AB/sub 5/ (finished-weight basis) were the most efficient, giving hydrogen evolution overpotentials (/eta/ /SUB H2/ ) of about 0.05 V at 200 mA cm/sup -2/. However, they tended to swell and shed material during electrolysis. Pressed, sintered cathodes containing 40-70 w/o catalyst in a nickel binder gave /eta/ /SUB H2/ about0.08 V; catalyst retention was excellent. Porous, sintered cathode coatings were made with 30-70 w/o AB/sub 5/ catalyst loadings. Their overpotentials were similar to those of the pressed, sintered cathodes. However, at catalyst loadings below about 40 w/o, high overpotentials characteristic of the nickel binder were observed. The structural and electrochemical properties of the three AB/sub 5/-catalyzed cathodes are discussed.

Filtered cathodic arc source

International Nuclear Information System (INIS)

Falabella, S.; Sanders, D.M.

1994-01-01

A continuous, cathodic arc ion source coupled to a macro-particle filter capable of separation or elimination of macro-particles from the ion flux produced by cathodic arc discharge is described. The ion source employs an axial magnetic field on a cathode (target) having tapered sides to confine the arc, thereby providing high target material utilization. A bent magnetic field is used to guide the metal ions from the target to the part to be coated. The macro-particle filter consists of two straight solenoids, end to end, but placed at 45 degree to one another, which prevents line-of-sight from the arc spot on the target to the parts to be coated, yet provides a path for ions and electrons to flow, and includes a series of baffles for trapping the macro-particles. 3 figures

Development of plasma cathode electron guns

Science.gov (United States)

Oks, Efim M.; Schanin, Peter M.

1999-05-01

The status of experimental research and ongoing development of plasma cathode electron guns in recent years is reviewed, including some novel upgrades and applications to various technological fields. The attractiveness of this kind of e-gun is due to its capability of creating high current, broad or focused beams, both in pulsed and steady-state modes of operation. An important characteristic of the plasma cathode electron gun is the absence of a thermionic cathode, a feature which leads to long lifetime and reliable operation even in the presence of aggressive background gas media and at fore-vacuum gas pressure ranges such as achieved by mechanical pumps. Depending on the required beam parameters, different kinds of plasma discharge systems can be used in plasma cathode electron guns, such as vacuum arcs, constricted gaseous arcs, hollow cathode glows, and two kinds of discharges in crossed E×B fields: Penning and magnetron. At the present time, plasma cathode electron guns provide beams with transverse dimension from fractional millimeter up to about one meter, beam current from microamperes to kiloamperes, beam current density up to about 100 A/cm2, pulse duration from nanoseconds to dc, and electron energy from several keV to hundreds of keV. Applications include electron beam melting and welding, surface treatment, plasma chemistry, radiation technologies, laser pumping, microwave generation, and more.

Understanding the Role of Temperature and Cathode Composition on Interface and Bulk: Optimizing Aluminum Oxide Coatings for Li-Ion Cathodes

International Nuclear Information System (INIS)

Han, Binghong; Paulauskas, Tadas; Key, Baris; Peebles, Cameron; Park, Joong Sun

2017-01-01

Here, surface coating of cathode materials with Al_2O_3 has been shown to be a promising method for cathode stabilization and improved cycling performance at high operating voltages. However, a detailed understanding on how coating process and cathode composition changes the chemical composition, morphology and distribution of coating within cathode interface and bulk lattice, is still missing. In this study, we use a wet-chemical method to synthesize a series of Al_2O_3-coated LiNi_0_._5Co_0_._2Mn_0_._3O_2 and LiCoO_2 cathodes treated under various annealing temperatures and a combination of structural characterization techniques to understand the composition, homogeneity and morphology of coating layer and the bulk cathode. Nuclear magnetic resonance and electron microscopy results reveal that the nature of the interface is highly depended on the annealing temperature and cathode composition. For Al_2O_3-coated LiNi_0_._5Co_0_._2Mn_0_._3O_2, higher annealing temperature leads to more homogeneous and more closely attached coating on cathode materials, corresponding to better electrochemical performance. Lower Al_2O_3 coating content is found to be helpful to further improve the initial capacity and cyclability, which can greatly outperform the pristine cathode material. For Al_2O_3-coated LiCoO_2, the incorporation of Al into the cathode lattice is observed after annealing at high temperatures, implying the transformation from “surface coatings” to “dopants”, which is not observed for LiNi_0_._5Co_0_._2Mn_0_._3O_2. As a result, Al_2O_3-coated LiCoO_2 annealed at higher temperature shows similar initial capacity but lower retention compared to that annealed at a lower temperature, due to the intercalation of surface alumina into the bulk layered structure forming a solid solution.

Understanding the Role of Temperature and Cathode Composition on Interface and Bulk: Optimizing Aluminum Oxide Coatings for Li-Ion Cathodes.

Science.gov (United States)

Han, Binghong; Paulauskas, Tadas; Key, Baris; Peebles, Cameron; Park, Joong Sun; Klie, Robert F; Vaughey, John T; Dogan, Fulya

2017-05-03

Surface coating of cathode materials with Al 2 O 3 has been shown to be a promising method for cathode stabilization and improved cycling performance at high operating voltages. However, a detailed understanding on how coating process and cathode composition change the chemical composition, morphology, and distribution of coating within the cathode interface and bulk lattice is still missing. In this study, we use a wet-chemical method to synthesize a series of Al 2 O 3 -coated LiNi 0.5 Co 0.2 Mn 0.3 O 2 and LiCoO 2 cathodes treated under various annealing temperatures and a combination of structural characterization techniques to understand the composition, homogeneity, and morphology of the coating layer and the bulk cathode. Nuclear magnetic resonance and electron microscopy results reveal that the nature of the interface is highly dependent on the annealing temperature and cathode composition. For Al 2 O 3 -coated LiNi 0.5 Co 0.2 Mn 0.3 O 2 , higher annealing temperature leads to more homogeneous and more closely attached coating on cathode materials, corresponding to better electrochemical performance. Lower Al 2 O 3 coating content is found to be helpful to further improve the initial capacity and cyclability, which can greatly outperform the pristine cathode material. For Al 2 O 3 -coated LiCoO 2 , the incorporation of Al into the cathode lattice is observed after annealing at high temperatures, implying the transformation from "surface coatings" to "dopants", which is not observed for LiNi 0.5 Co 0.2 Mn 0.3 O 2 . As a result, Al 2 O 3 -coated LiCoO 2 annealed at higher temperature shows similar initial capacity but lower retention compared to that annealed at a lower temperature, due to the intercalation of surface alumina into the bulk layered structure forming a solid solution.

Magnetic properties of La2NiO4.16 and La2-xPrxNiO4+δ

International Nuclear Information System (INIS)

Poirot, N.J.; Allancon, Ch.; Odier, P.; Simon, P.; Bassat, J.M.; Loup, J.P.

1998-01-01

Magnetic properties of La 2 NiO 4.16 and La 2-x Pr x NiO 4+δ are studied by dc susceptibility in a wide temperature range, i.e., 4--1,200 K. The principal aim is to investigate the modifications of magnetic interactions in the NiO 2 plane by inserting a magnetic ion in the LaO layer. Magnetic properties are considerably different with and without praseodymium. When 0 0.5, a single Pr 3+ effect might dominate

Li- and Mn-Rich Cathode Materials: Challenges to Commercialization

Energy Technology Data Exchange (ETDEWEB)

Zheng, Jianming [Energy and Environmental Directorate, Pacific Northwest National Laboratory, 902 Battelle Boulevard Richland WA 99354 USA; Myeong, Seungjun [School of Energy and Chemical Engineering, Green Energy Materials Development Center, Ulsan National Institute of Science and Technology (UNIST), Korea 689-798; Cho, Woongrae [School of Energy and Chemical Engineering, Green Energy Materials Development Center, Ulsan National Institute of Science and Technology (UNIST), Korea 689-798; Yan, Pengfei [Environmental Molecular Sciences Laboratory, Pacific Northwest National Laboratory, 902 Battelle Boulevard Richland WA 99354 USA; Xiao, Jie [Energy and Environmental Directorate, Pacific Northwest National Laboratory, 902 Battelle Boulevard Richland WA 99354 USA; Wang, Chongmin [Environmental Molecular Sciences Laboratory, Pacific Northwest National Laboratory, 902 Battelle Boulevard Richland WA 99354 USA; Cho, Jaephil [School of Energy and Chemical Engineering, Green Energy Materials Development Center, Ulsan National Institute of Science and Technology (UNIST), Korea 689-798; Zhang, Ji-Guang [Energy and Environmental Directorate, Pacific Northwest National Laboratory, 902 Battelle Boulevard Richland WA 99354 USA

2016-12-14

The lithium- and manganese-rich (LMR) layered structure cathode exhibit one of the highest specific energy (~900 Wh kg-1) among all the cathode materials. However, the practical applications of LMR cathodes are still hindered by several significant challenges including voltage fade, large initial capacity loss, poor rate capability and limited cycle life. Herein, we review the recent progresses and understandings on the application of LMR cathode materials from practical point of view. Several key parameters of LMR cathodes that affect the LMR/graphite full cell operation are systematically analysed. These factors include the first cycle capacity loss, voltage fade, powder tap density, electrode density of LMR based cathode etc. New approaches to minimize the detrimental effect of these factors are highlighted in this work. We also provided the perspectives for the future research on LMR cathode materials, focusing on addressing the fundamental problems of LMR cathodes while always keeping practical considerations in mind.

Degradation factors of a new long life cathode

International Nuclear Information System (INIS)

Zhang Mingchen; Zhang Honglai; Liu Pukun; Li Yutao

2011-01-01

This paper analyses the degradation factors of a new long life coated impregnated cathode after accelerated life test. The surface state of the cathode is investigated with scanning electron microscope (SEM) as well as the content and variation of the various elements on the surface and the longitudinal section of the cathode are analyzed with Auger electron spectroscopy (AES) before and after the life test. The analyzing results with SEM show that the cathode coating shrinks at the life end and leads to a rise in its work function. The analyzing results with AES show that the percent of the W increases and the active materials Ba decreases on the cathode surface at the life end. Furthermore, there is less Ba underneath the cathode surface but still a lot of Ba in the tungsten matrix at the life end.

Cathode Composition in a Saltwater Metal-Air Battery

Directory of Open Access Journals (Sweden)

William Shen

2017-01-01

Full Text Available Metal-air batteries consist of a solid metal anode and an oxygen cathode of ambient air, typically separated by an aqueous electrolyte. Here, simple saltwater-based models of aluminum-air and zinc-air cells are used to determine the differences between theoretical cell electric potentials and experimental electric potentials. A substantial difference is observed. It is also found that the metal cathode material is crucial to cell electric potential, despite the cathode not participating in the net reaction. Finally, the material composition of the cathode appears to have a more significant impact on cell potential than the submerged surface area of the cathode.

Photoelectron spectroscopy study on Li substituted NiO using PES beamline installed on Indus-1

Science.gov (United States)

Banerjee, A.; Chaudhari, S. M.; Phase, D. M.; Dasannacharya, B. A.

2003-01-01

Photoelectron spectroscopy beamline based on a toroidal grating monochromator (TGM) is recently commissioned on Indus-1 storage ring. It has been used to carry out valence band photoemission study of Li substituted NiO. In this paper initially a brief description of the beamline components and the experimental station for angle integrated photoemission experiment is presented. The later part of this paper is devoted to studies carried out on Li xNi 1- xO with x=0.0, 0.35 and 0.5 samples. Thin pellets of polycrystalline samples were used for the measurements reported here. Valence band spectra recorded on polycrystalline Li xNi 1- xO samples show drastic changes in various features as compared to that of pure NiO. The prominent changes are: (i) change in the relative contributions of Ni-3d and O-2p emissions, (ii) change in the peak position of Ni-3d from the top of the valance band of NiO and (iii) no noticeable change in the Ni satellite peak. These results are evaluated in terms of earlier findings in pure and low Li doped NiO.

Nanostructured lanthanum manganate composite cathode

DEFF Research Database (Denmark)

Wang, Wei Guo; Liu, Yi-Lin; Barfod, Rasmus

2005-01-01

that the (La1-xSrx)(y)MnO3 +/-delta (LSM) composite cathodes consist of a network of homogenously distributed LSM, yttria-stabilized zirconia (YSZ), and pores. The individual grain size of LSM or YSZ is approximately 100 nm. The degree of contact between cathode and electrolyte is 39% on average. (c) 2005...

Heating of refractory cathodes by high-pressure arc plasmas: II

International Nuclear Information System (INIS)

Benilov, M S; Cunha, M D

2003-01-01

Solitary spots on infinite planar cathodes and diffuse and axially symmetric spot modes on finite cathodes of high-pressure arc discharges are studied in a wide range of arc currents. General features are analysed and extensive numerical results on planar and cylindrical tungsten cathodes of atmospheric-pressure argon arcs are given for currents of up to 100 kA. It is shown, in particular, that the temperature of cathode surface inside a solitary spot varies relatively weakly and may be estimated, to the accuracy of about 200-300 K, without actually solving the thermal conduction equation in the cathode body. Asymptotic behaviour of solutions for finite cathodes in the limiting case of high currents is found and confirmed by numerical results. A general pattern of current-voltage characteristics of various modes on finite cathodes suggested previously on the basis of bifurcation analysis is confirmed. A transition from the spot modes on a finite cathode in the limit of large cathode dimensions to the solitary spot mode on an infinite planar cathode is studied. It is found that the solitary spot mode represents a limiting form of the high-voltage spot mode on a finite cathode. A question of distinguishing between diffuse and spot modes on finite cathodes is considered

Co-deposition of metallic actinides on a solid cathode

Energy Technology Data Exchange (ETDEWEB)

Limmer, S. J.; Williamson, M. A.; Willit, J. L. [Argonne National Laboratory, Argonne (United States)

2008-08-15

The amount of rare earth contamination that will be found in a co-deposit of actinides is a function of the type of cathode used. A non-alloying solid cathode will result in a significantly lower rare earth contamination in the actinide co-deposit than a liquid cadmium cathode. With proper control of the cathode potential vs. a stable reference electrode, co-deposition of uranium with other more electroactive metals has been demonstrated using a non-alloying solid cathode.

Co-deposition of metallic actinides on a solid cathode

International Nuclear Information System (INIS)

Limmer, S. J.; Williamson, M. A.; Willit, J. L.

2008-01-01

The amount of rare earth contamination that will be found in a co-deposit of actinides is a function of the type of cathode used. A non-alloying solid cathode will result in a significantly lower rare earth contamination in the actinide co-deposit than a liquid cadmium cathode. With proper control of the cathode potential vs. a stable reference electrode, co-deposition of uranium with other more electroactive metals has been demonstrated using a non-alloying solid cathode

Properties of NiO thin films deposited by chemical spray pyrolysis using different precursor solutions

Energy Technology Data Exchange (ETDEWEB)

Cattin, L. [Universite de Nantes, Nantes Atlantique Universites, LAMP, EA 3825, Faculte des Sciences et des Techniques, 2 rue de la Houssiniere, BP 92208, Nantes F-44000 (France); Reguig, B.A.; Khelil, A. [Universite d' Oran Es-Senia, LPCM2E (Algeria); Morsli, M. [Universite de Nantes, Nantes Atlantique Universites, LAMP, EA 3825, Faculte des Sciences et des Techniques, 2 rue de la Houssiniere, BP 92208, Nantes F-44000 (France); Benchouk, K. [Universite d' Oran Es-Senia, LPCM2E (Algeria); Bernede, J.C. [Universite de Nantes, Nantes Atlantique Universites, LAMP, EA 3825, Faculte des Sciences et des Techniques, 2 rue de la Houssiniere, BP 92208, Nantes F-44000 (France)], E-mail: Jean-Christian.Bernede@univ-nantes.fr

2008-07-15

NiO thin films have been deposited by chemical spray pyrolysis using a perfume atomizer to grow the aerosol. The influence of the precursor, nickel chloride hexahydrate (NiCl{sub 2}.6H{sub 2}O), nickel nitrate hexahydrate (Ni(NO{sub 3}){sub 2}.6H{sub 2}O), nickel hydroxide hexahydrate (Ni(OH){sub 2}.6H{sub 2}O), nickel sulfate tetrahydrate (NiSO{sub 4}.4H{sub 2}O), on the thin films properties has been studied. In the experimental conditions used (substrate temperature 350 deg. C, precursor concentration 0.2-0.3 M, etc.), pure NiO thin films crystallized in the cubic phase can be achieved only with NiCl{sub 2} and Ni(NO{sub 3}){sub 2} precursors. These films have been post-annealed at 425 deg. C for 3 h either in room atmosphere or under vacuum. If all the films are p-type, it is shown that the NiO films conductivity and optical transmittance depend on annealing process. The properties of the NiO thin films annealed under room atmosphere are not significantly modified, which is attributed to the fact that the temperature and the environment of this annealing is not very different from the experimental conditions during spray deposition. The annealing under vacuum is more efficient. This annealing being proceeded in a vacuum no better than 10{sup -2} Pa, it is supposed that the modifications of the NiO thin film properties, mainly the conductivity and optical transmission, are related to some interaction between residual oxygen and the films.

Património, turismo e emoção

Directory of Open Access Journals (Sweden)

Carlos Fortuna

2013-04-01

Full Text Available Depois de discutir a relação entre património e tradição, este texto trata da complexidade da atribuição de significado ao património, aos objetos, lugares ou práticas socioculturais. O turismo surge como um poderoso meio da valorização emocional do significado patrimonial desses objetos, lugares e práticas sociais. A atual busca de experiências emocionais continua a tomar lugar central no desenvolvimento do turismo de memória, mas também no turismo negro e no da realidade. Os diferentes modos da sua perceção são vistos como modalidades de disputa social de sentidos, incluindo as narrativas pós‑coloniais do turismo. Nestes dias de valorização da experiência psicoemocional dos turistas, admite‑se que a oferta turística de forte sentido emocional possa aumentar acentuadamente em todo o mundo.

Impedance of porous IT-SOFC LSCF:CGO composite cathodes

DEFF Research Database (Denmark)

Nielsen, Jimmi; Jacobsen, Torben; Wandel, Marie

2011-01-01

The impedance of technological relevant LSCF:CGO composite IT-SOFC cathodes was studied over a very wide performance range. This was experimentally achieved by impedance measurements on symmetrical cells with three different microstructures in the temperature range 550–850 °C. In order to account...... for the impedance spectra of the poor performing cathodes the Finite-Length-Gerischer (FLG) impedance was derived and applied to the impedance data. The FLG impedance describes for a given microstructure the situation where the cathode is made too thin from a cathode development point of view. The moderate...... performing cathodes showed a slightly suppressed Gerischer impedance, while the impedance spectra of the well performing cathodes showed the presence of an arc due to oxygen gas diffusion. The overall impedance of the well performing cathodes could be described with a slightly suppressed Gerischer impedance...

Thermal oxidation of InP surfaces modified with NiO + PbO mixtures

International Nuclear Information System (INIS)

Mittova, I.Ya.; Tomina, E.V.; Samsonov, A.A.; Lukin, A.N.; Simonov, S.P.

2005-01-01

The oxidation kinetics of (NiO + PbO)/InP, NiO/InP and PbO/InP structures in an oxygen flow is studied in the temperature range of 400-550 deg C. It is shown by IR spectroscopy that the thermal oxidation of (NiO + PbO)/InP structures leads to the formation of nickel and lead polyphosphates and indium ortho- and metaphosphates. The nickel phosphates may then gradually transform into diphosphates, depending on the oxidation temperature, whereas the lead phosphates undergo no changes [ru

Preventing Corrosion by Controlling Cathodic Reaction Kinetics

Science.gov (United States)

2016-03-25

3. DATES COVERED (From - To) 09/23/15 - 04/22/16 4. TITLE AND SUBTITLE Sa. CONTRACT NUMBER Preventing Corrosion by Controlling Cathodic Reaction...Preventing corrosion by controlling cathodic reaction kinetics Progress Report for Period: 1 SEP 2015-31 MAR 2016 John Keith Department of...25 March 2016 Preventing corrosion by controlling cathodic reaction kinetics Annual Summary Report: FY16 PI: John Keith, 412-624-7016,jakeith

Knife-edge thin film field emission cathodes

International Nuclear Information System (INIS)

Lee, B.; Demroff, H.P.; Drew, M.M.; Elliott, T.S.; Mazumdar, T.K.; McIntyre, P.M.; Pang, Y.; Smith, D.D.; Trost, H.J.

1993-01-01

Cathodes made of thin-film field emission arrays (FEA) have the advantages of high current density, pulsed emission, and low bias voltage operation. The authors have developed a technology to fabricate knife-edge field emission cathodes on (110) silicon wafers. The emitter geometry is optimized for efficient modulation at high frequency. Cathode fabrication progress and preliminary analysis of their applications in RF power sources are presented

Cold cathode diode X-ray source

International Nuclear Information System (INIS)

Cooperstein, G.; Lanza, R.C.; Sohval, A.R.

1983-01-01

A cold cathode diode X-ray source for radiation imaging, especially computed tomography, comprises a rod-like anode and a generally cylindrical cathode, concentric with the anode. The spacing between anode and cathode is so chosen that the diode has an impedance in excess of 100 ohms. The anode may be of tungsten, or of carbon with a tungsten and carbon coating. An array of such diodes may be used with a closely packed array of detectors to produce images of rapidly moving body organs, such as the beating heart. (author)

Effect of different nickel precursors on capacitive behavior of electrodeposited NiO thin films

Energy Technology Data Exchange (ETDEWEB)

Kore, R. M.; Ghadge, T. S.; Ambare, R. C.; Lokhande, B. J., E-mail: bjlokhande@yahoo.com [School of Physical Sciences, Solapur University, Solapur-413 255, M.S. (India)

2016-04-13

In the present study, the effect of nickel precursors containing different anions like nitrate, chloride and sulphate on the morphology and pseudocapacitance behavior of NiO is investigated. The NiO samples were prepared by using a potentiondynamic electrodeposition technique in the three electrode cell. Cyclic voltammetry technique was exploited for potentiodynamic deposition of the films. The obtained samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), etc. The XRD reveals the cubic crystal structure for all samples. The SEM micrograph shows nanoflakelike, up grown nanoflakes and honeycomb like nanostructured morphologies for nitrate, chloride and sulphate precursors respectively. The capacitive behavior of these samples was recorded using cyclic voltammetry (CV), charge-discharge and electrochemical impedance spectroscopy (EIS) in 1 M KOH electrolyte. The specific capacitance values of NiO samples obtained using CV for nitrate, chloride and sulphate precursors were 136, 214 and 893 Fg{sup −1} respectively, at the scan rate of 5 mVs{sup −1}. The charge discharge study shows high specific energy for the sample obtained from sulphate (23.98 Whkg{sup −1}) as compared to chloride (9.67 Whkg{sup −1}) and nitrate (4.9 Whkg{sup −1}), whereas samples of cholride (13.9 kWkg{sup −1} and nitrate (10.5 kWkg{sup −1}) shows comparatively more specific power than samples obtained from sulphate (7.6 kWkg{sup −1}). The equivalent series resistance of NiO samples observed from EIS study are 1.34, 1.29 and 1.27 Ω respectively for nitrate, chloride and sulphate precursors. These results emphasizes that the samples obtained from sulphate precursors provides very low impedance through honeycomb like nanostructured morphology which supports good capacitive behavior of NiO.

Energetics of intrinsic defects in NiO and the consequences for its resistive random access memory performance

Energy Technology Data Exchange (ETDEWEB)

Dawson, J. A., E-mail: jad95@cam.ac.uk; Guo, Y.; Robertson, J. [Department of Engineering, University of Cambridge, Cambridge CB2 1PZ (United Kingdom)

2015-09-21

Energetics for a variety of intrinsic defects in NiO are calculated using state-of-the-art ab initio hybrid density functional theory calculations. At the O-rich limit, Ni vacancies are the lowest cost defect for all Fermi energies within the gap, in agreement with the well-known p-type behaviour of NiO. However, the ability of the metal electrode in a resistive random access memory metal-oxide-metal setup to shift the oxygen chemical potential towards the O-poor limit results in unusual NiO behaviour and O vacancies dominating at lower Fermi energy levels. Calculated band diagrams show that O vacancies in NiO are positively charged at the operating Fermi energy giving it the advantage of not requiring a scavenger metal layer to maximise drift. Ni and O interstitials are generally found to be higher in energy than the respective vacancies suggesting that significant recombination of O vacancies and interstitials does not take place as proposed in some models of switching behaviour.

Energetics of intrinsic defects in NiO and the consequences for its resistive random access memory performance

International Nuclear Information System (INIS)

Dawson, J. A.; Guo, Y.; Robertson, J.

2015-01-01

Energetics for a variety of intrinsic defects in NiO are calculated using state-of-the-art ab initio hybrid density functional theory calculations. At the O-rich limit, Ni vacancies are the lowest cost defect for all Fermi energies within the gap, in agreement with the well-known p-type behaviour of NiO. However, the ability of the metal electrode in a resistive random access memory metal-oxide-metal setup to shift the oxygen chemical potential towards the O-poor limit results in unusual NiO behaviour and O vacancies dominating at lower Fermi energy levels. Calculated band diagrams show that O vacancies in NiO are positively charged at the operating Fermi energy giving it the advantage of not requiring a scavenger metal layer to maximise drift. Ni and O interstitials are generally found to be higher in energy than the respective vacancies suggesting that significant recombination of O vacancies and interstitials does not take place as proposed in some models of switching behaviour

Research and Development of a New Field Enhanced Low Temperature Thermionic Cathode that Enables Fluorescent Dimming and Loan Shedding without Auxiliary Cathode Heating

Energy Technology Data Exchange (ETDEWEB)

Feng Jin

2009-01-07

This is the final report for project entitled 'Research and development of a new field enhanced low temperature thermionic cathode that enables fluorescent dimming and load shedding without auxiliary cathode heating', under Agreement Number: DE-FC26-04NT-42329. Under this project, a highly efficient CNT based thermionic cathode was demonstrated. This cathode is capable of emitting electron at a current density two order of magnitude stronger then a typical fluorescent cathode at same temperatures, or capable of emitting at same current density but at temperature about 300 C lower than that of a fluorescent cathode. Detailed fabrication techniques were developed including CVD growth of CNTs and sputter deposition of oxide thin films on CNTs. These are mature technologies that have been widely used in industry for large scale materials processing and device fabrications, thus, with further development work, the techniques developed in this project can be scaled-up in manufacturing environment. The prototype cathodes developed in this project were tested in lighting plasma discharge environment. In many cases, they not only lit and sustain the plasma, but also out perform the fluorescent cathodes in key parameters such like cathode fall voltages. More work will be needed to further evaluate more detailed and longer term performance of the prototype cathode in lighting plasma.

Well-dispersed NiO nanoparticles supported on nitrogen-doped carbon nanotube for methanol electrocatalytic oxidation in alkaline media

Energy Technology Data Exchange (ETDEWEB)

Wang, Pengcheng; Zhou, Yingke, E-mail: zhouyk888@hotmail.com; Hu, Min; Chen, Jian

2017-01-15

Highlights: • Nitrogen-doped carbon nanotube supporting ultrafine NiO nanoparticles with high dispersity are facile synthesized. • The nitrogen doping, calcination temperature and NiO loading present great effects on the catalyst morphology, structure and electrochemical performance. • NiO-NCNT-3x-400 demonstrates remarkable catalytic activity and stability for the methanol electrolytic oxidation reaction. - Abstract: Nitrogen-doped carbon nanotube supporting NiO nanoparticles were synthesized by a chemical precipitation process coupled with subsequent calcination. The morphology and structure of the composites were characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS), and the electrochemical performance was evaluated using cyclic voltammetry and chronoamperometric technique. The effects of nitrogen doping, calcination temperature and content of NiO nanoparticles on the electrocatalytic activity toward methanol oxidation were systematically studied. The results show that the uniformly dispersed ultrafine NiO nanoparticles supported on nitrogen-doped carbon nanotube are obtained after calcination at 400 °C. The optimized composite catalysts present high electrocatalytic activity, fast charge-transfer process, excellent accessibility and stability for methanol oxidation reaction, which are promising for application in the alkaline direct methanol fuel cells.

High Performance Cathodes for Li-Air Batteries

Energy Technology Data Exchange (ETDEWEB)

Xing, Yangchuan

2013-08-22

The overall objective of this project was to develop and fabricate a multifunctional cathode with high activities in acidic electrolytes for the oxygen reduction and evolution reactions for Li-air batteries. It should enable the development of Li-air batteries that operate on hybrid electrolytes, with acidic catholytes in particular. The use of hybrid electrolytes eliminates the problems of lithium reaction with water and of lithium oxide deposition in the cathode with sole organic electrolytes. The use of acid electrolytes can eliminate carbonate formation inside the cathode, making air breathing Li-air batteries viable. The tasks of the project were focused on developing hierarchical cathode structures and bifunctional catalysts. Development and testing of a prototype hybrid Li-air battery were also conducted. We succeeded in developing a hierarchical cathode structure and an effective bifunctional catalyst. We accomplished integrating the cathode with existing anode technologies and made a pouch prototype Li-air battery using sulfuric acid as catholyte. The battery cathodes contain a nanoscale multilayer structure made with carbon nanotubes and nanofibers. The structure was demonstrated to improve battery performance substantially. The bifunctional catalyst developed contains a conductive oxide support with ultra-low loading of platinum and iridium oxides. The work performed in this project has been documented in seven peer reviewed journal publications, five conference presentations, and filing of two U.S. patents. Technical details have been documented in the quarterly reports to DOE during the course of the project.

Cationic fluorinated polymer binders for microbial fuel cell cathodes

KAUST Repository

Chen, Guang; Wei, Bin; Logan, Bruce E.; Hickner, Michael A.

2012-01-01

Fluorinated quaternary ammonium-containing polymers were used as catalyst binders in microbial fuel cell (MFC) cathodes. The performance of the cathodes was examined and compared to NAFION ® and other sulfonated aromatic cathode catalyst binders using linear sweep voltammetry (LSV), impedance spectroscopy, and performance tests in single chamber air-cathode MFCs. The cathodes with quaternary ammonium functionalized fluorinated poly(arylene ether) (Q-FPAE) binders showed similar current density and charge transfer resistance (R ct) to cathodes with NAFION ® binders. Cathodes containing either of these fluorinated binders exhibited better electrochemical responses than cathodes with sulfonated or quaternary ammonium-functionalized RADEL ® poly(sulfone) (S-Radel or Q-Radel) binders. After 19 cycles (19 d), the power densities of all the MFCs declined compared to the initial cycles due to biofouling at the cathode. MFC cathodes with fluorinated polymer binders (1445 mW m -2, Q-FPAE-1.4-H; 1397 mW m -2, Q-FPAE-1.4-Cl; 1277 mW m -2, NAFION ®; and 1256 mW m -2, Q-FPAE-1.0-Cl) had better performance than those with non-fluorinated polymer binders (880 mW m -2, S-Radel; 670 mW m -2, Q-Radel). There was a 15% increase in the power density using the Q-FPAE binder with a 40% higher ion exchange capacity (Q-FPAE-1.4-H compared to Q-FPAE-1.0-Cl) after 19 cycles of operation, but there was no effect on the power production due to counter ions in the binder (Cl -vs. HCO 3 -). The highest-performance cathodes (NAFION ® and Q-FPAE binders) had the lowest charge transfer resistances (R ct) in fresh and in fouled cathodes despite the presence of thick biofilms on the surface of the electrodes. These results show that fluorinated binders may decrease the penetration of the biofilm and associated biopolymers into the cathode structure, which helps to combat MFC performance loss over time. © 2012 The Royal Society of Chemistry.

Development and evaluation of carbon and binder loading in low-cost activated carbon cathodes for air-cathode microbial fuel cells

KAUST Repository

Wei, Bin; Tokash, Justin C.; Chen, Guang; Hickner, Michael A.; Logan, Bruce E.

2012-01-01

Activated carbon (AC) air cathodes were constructed using variable amounts of carbon (43-171 mg cm-2) and an inexpensive binder (10 wt% polytetrafluoroethylene, PTFE), and with or without a porous cloth wipe-based diffusion layer (DL) that was sealed with PDMS. The cathodes with the highest AC loading of 171 mg cm-2, and no diffusion layer, produced 1255 ± 75 mW m-2 and did not appreciably vary in performance after 1.5 months of operation. Slightly higher power densities were initially obtained using 100 mg cm-2 of AC (1310 ± 70 mW m-2) and a PDMS/wipe diffusion layer, although the performance of this cathode decreased to 1050 ± 70 mW m-2 after 1.5 months, and 1010 ± 190 mW m-2 after 5 months. AC loadings of 43 mg cm-2 and 100 mg cm-2 did not appreciably affect performance (with diffusion layers). MFCs with the Pt catalyst and Nafion binder initially produced 1295 ± 13 mW m-2, but the performance decreased to 930 ± 50 mW m -2 after 1.5 months, and then to 890 ± 20 mW m-2 after 5 months. Cathode performance was optimized for all cathodes by using the least amount of PTFE binder (10%, in tests using up to 40%). These results provide a method to construct cathodes for MFCs that use only inexpensive AC and a PTFE, while producing power densities similar to those of Pt/C cathodes. The methods used here to make these cathodes will enable further tests on carbon materials in order to optimize and extend the lifetime of AC cathodes in MFCs. © 2012 The Royal Society of Chemistry.

High Performance Fe-Co Based SOFC Cathodes

DEFF Research Database (Denmark)

Kammer Hansen, Kent; Hansen, Karin Vels; Mogensen, Mogens Bjerg

2010-01-01

With the aim of reducing the temperature of the solid oxide fuel cell (SOFC), a new high-performance perovskite cathode has been developed. An area-specific resistance (ASR) as low as 0.12 Ωcm2 at 600 °C was measured by electrochemical impedance spectroscopy (EIS) on symmetrical cells. The cathode...... is a composite between (Gd0.6Sr0.4)0.99Fe0.8Co0.2O3-δ (GSFC) and Ce0.9Gd0.1O1.95 (CGO10). Examination of the microstructure of the cathodes by scanning electron microscopy (SEM) revealed a possibility of further optimisation of the microstructure in order to increase the performance of the cathodes. It also...... seems that an adjustment of the sintering temperature will make a lowering of the ASR value possible. The cathodes were compatible with ceria-based electrolytes but reacted to some extent with zirconia-based electrolytes depending on the sintering temperature....

Model of dopant action in oxide cathodes

International Nuclear Information System (INIS)

Engelsen, Daniel den; Gaertner, Georg

2005-01-01

The paper describes an electrochemical model, which largely explains the formation of Ba in the oxide cathode at activation and normal operation. In a non-doped oxide cathode electrolysis of BaO is, besides the exchange reaction from the activators in the cathode nickel, an important source of Ba. By doping with rare earth oxides the conductivity of the oxide layer increases, which implies that the potential difference during current drawing over the oxide layer becomes lower and electrolysis of BaO is suppressed. This implies that the part of the electronic conductivity of the (Ba,Sr)O layer induced by the dopants also controls the sensitivity for poisoning: the higher the dopant level, the larger the sensitivity for poisoning. Furthermore, the suppression of electrolysis during normal operation largely explains why doped oxide cathodes have a better life performance than non-doped cathodes. Finally a hypothesis on the enhancement of sintering upon doping is presented

Manganese Dioxide As Rechargeable Magnesium Battery Cathode

International Nuclear Information System (INIS)

Ling, Chen; Zhang, Ruigang

2017-01-01

Rechargeable magnesium battery (rMB) has received increased attention as a promising alternative to current Li-ion technology. However, the lack of appropriate cathode that provides high-energy density and good sustainability greatly hinders the development of practical rMBs. To date, the successful Mg 2+ -intercalation was only achieved in only a few cathode hosts, one of which is manganese dioxide. This review summarizes the research activity of studying MnO 2 in magnesium cells. In recent years, the cathodic performance of MnO 2 was impressively improved to the capacity of >150–200 mAh g −1 at voltage of 2.6–2.8 V with cyclability to hundreds or more cycles. In addition to reviewing electrochemical performance, we sketch a mechanistic picture to show how the fundamental understanding about MnO 2 cathode has been changed and how it paved the road to the improvement of cathode performance.

Manganese Dioxide As Rechargeable Magnesium Battery Cathode

Energy Technology Data Exchange (ETDEWEB)

Ling, Chen, E-mail: chen.ling@toyota.com; Zhang, Ruigang [Toyota Research Institute of North America, Ann Arbor, MI (United States)

2017-11-03

Rechargeable magnesium battery (rMB) has received increased attention as a promising alternative to current Li-ion technology. However, the lack of appropriate cathode that provides high-energy density and good sustainability greatly hinders the development of practical rMBs. To date, the successful Mg{sup 2+}-intercalation was only achieved in only a few cathode hosts, one of which is manganese dioxide. This review summarizes the research activity of studying MnO{sub 2} in magnesium cells. In recent years, the cathodic performance of MnO{sub 2} was impressively improved to the capacity of >150–200 mAh g{sup −1} at voltage of 2.6–2.8 V with cyclability to hundreds or more cycles. In addition to reviewing electrochemical performance, we sketch a mechanistic picture to show how the fundamental understanding about MnO{sub 2} cathode has been changed and how it paved the road to the improvement of cathode performance.

Separation of Electrolytic Reduction Product from Stainless Steel Wire Mesh Cathode Basket via Salt Draining and Reuse of the Cathode Basket

Directory of Open Access Journals (Sweden)

Eun-Young Choi

2017-01-01

Full Text Available We demonstrated that the metallic product obtained after electrolytic reduction (also called oxide reduction (OR can be simply separated from a stainless steel wire mesh cathode basket only by using a salt drain. First, the OR run of a simulated oxide fuel (0.6 kg/batch was conducted in a molten Li2O–LiCl salt electrolyte at 650°C. The simulated oxide fuel of the porous cylindrical pellets was used as a cathode by loading a stainless steel wire mesh cathode basket. Platinum was employed as an anode. After the electrolysis, the residual salt of the cathode basket containing the reduction product was drained by placing it at gas phase above the molten salt using a holder. Then, at a room temperature, the complete separation of the reduction product from the cathode basket was achieved by inverting it without damaging or deforming the basket. Finally, the emptied cathode basket obtained after the separation was reused for the second OR run by loading a fresh simulated oxide fuel. We also succeeded in the separation of the metallic product from the reused cathode basket for the second OR run.

Progress of air-breathing cathode in microbial fuel cells

Science.gov (United States)

Wang, Zejie; Mahadevan, Gurumurthy Dummi; Wu, Yicheng; Zhao, Feng

2017-07-01

Microbial fuel cell (MFC) is an emerging technology to produce green energy and vanquish the effects of environmental contaminants. Cathodic reactions are vital for high electrical power density generated from MFCs. Recently tremendous attentions were paid towards developing high performance air-breathing cathodes. A typical air-breathing cathode comprises of electrode substrate, catalyst layer, and air-diffusion layer. Prior researches demonstrated that each component influenced the performance of air-breathing cathode MFCs. This review summarized the progress in development of the individual component and elaborated main factors to the performance of air-breathing cathode.

The improvement of all-solid-state electrochromic devices fabricated with the reactive sputter and cathodic arc technology

Directory of Open Access Journals (Sweden)

Min-Chuan Wang

2016-11-01

Full Text Available The all-solid-state electrochromic device (ECD with the one substrate structure fabricated by the reactive dc magnetron sputtering (DCMS and cathodic vacuum arc plasma (CVAP technology has been developed for smart electrochromic (EC glass application. The EC layer and ion conductor layer were deposited by reactive DCMS and CVAP technology, respectively. The ion conductor layer Ta2O5 deposited by the CVAP technology has provided the better porous material structure for ion transportation and showed 1.76 times ion conductivity than devices with all sputtering process. At the same time, the EC layer WO3 and NiO deposited by the reactive DCMS have also provided the high quality and uniform characteristic to overcome the surface roughness effect of the CVAP ion conductor layer in multilayer device structure. The all-solid-state ECD with the CVAP ion conductor layer has demonstrated a maximum transmittance variation (ΔT of 55% at 550nm and a faster-switching speed. Furthermore, the lower equipment cost and higher deposition rate could be achieved by the application of CVAP technology.

Joule heat generation in thermionic cathodes of high-pressure arc discharges

Energy Technology Data Exchange (ETDEWEB)

Benilov, M. S.; Cunha, M. D. [Departamento de Fisica, CCCEE, Universidade da Madeira, Largo do Municipio, 9000 Funchal (Portugal)

2013-02-14

The nonlinear surface heating model of plasma-cathode interaction in high-pressure arcs is extended to take into account the Joule effect inside the cathode body. Calculation results are given for different modes of current transfer to tungsten cathodes of different configurations in argon plasmas of atmospheric or higher pressures. Special attention is paid to analysis of energy balances of the cathode and the near-cathode plasma layer. In all the cases, the variation of potential inside the cathode is much smaller than the near-cathode voltage drop. However, this variation can be comparable to the volt equivalent of the energy flux from the plasma to the cathode and then the Joule effect is essential. Such is the case of the diffuse and mixed modes on rod cathodes at high currents, where the Joule heating causes a dramatic change of thermal and electrical regimes of the cathode. The Joule heating has virtually no effect over characteristics of spots on rod and infinite planar cathodes.

Effects of the thickness of NiO hole transport layer on the performance of all-inorganic quantum dot light emitting diode

International Nuclear Information System (INIS)

Zhang, Xiao Li; Dai, Hai Tao; Zhao, Jun Liang; Li, Chen; Wang, Shu Guo; Sun, Xiao Wei

2014-01-01

All-inorganic quantum dot light emitting diodes (QLEDs) have recently gained great attention owing to their high stability under oxygenic, humid environment and higher operating currents. In this work, we fabricated all-inorganic CdSe/ZnS core-shell QLEDs composed of ITO/NiO/QDs/ZnO/Al, in which NiO and ZnO thin film deposited via all-solution method were employed as hole and electron transport layer, respectively. To achieve high light emitting efficiency, the balance transport between electrons and holes play a key role. In this work, the effects of the thickness of NiO film on the performance of QLEDs were explored experimentally in details. NiO layers with various thicknesses were prepared with different rotation speeds. Experimental results showed that thinner NiO layer deposited at higher rotation speed had higher transmittance and larger band gap. Four typical NiO thickness based QLEDs were fabricated to optimize the hole transport layer. Thinner NiO layer based device performs bright emission with high current injection, which is ascribed to the reduced barrier height between hole transport layer and quantum dot. - Highlights: • All-inorganic quantum dot light emitting diodes (QLEDs) were fabricated. • Thinner NiO film can effectively enhance on–off properties of devices. • Improved performance of QLEDs is mainly attributed to energy barrier reduction

Rf Gun with High-Current Density Field Emission Cathode

International Nuclear Information System (INIS)

Jay L. Hirshfield

2005-01-01

High current-density field emission from an array of carbon nanotubes, with field-emission-transistor control, and with secondary electron channel multiplication in a ceramic facing structure, have been combined in a cold cathode for rf guns and diode guns. Electrodynamic and space-charge flow simulations were conducted to specify the cathode configuration and range of emission current density from the field emission cold cathode. Design of this cathode has been made for installation and testing in an existing S-band 2-1/2 cell rf gun. With emission control and modulation, and with current density in the range of 0.1-1 kA/cm2, this cathode could provide performance and long-life not enjoyed by other currently-available cathodes

O patrimônio ambiental urbano: uma conceituação ampliada e aperfeiçoada

OpenAIRE

Yázigi, Eduardo; Professor da Universidade de São Paulo

2012-01-01

Pode existir preservação sem preservação social? Sob quais condições? Em que restritos termos poderia uma paisagem ser considerada patrimônio preservável? Tais problemáticas constituem o fio condutor do artigo que trata do patrimônio ambiental urbano, participação popular e sua preservação.

Using cathode spacers to minimize reactor size in air cathode microbial fuel cells

KAUST Repository

Yang, Qiao

2012-04-01

Scaling up microbial fuel cells (MFCs) will require more compact reactor designs. Spacers can be used to minimize the reactor size without adversely affecting performance. A single 1.5mm expanded plastic spacer (S1.5) produced a maximum power density (973±26mWm -2) that was similar to that of an MFC with the cathode exposed directly to air (no spacer). However, a very thin spacer (1.3mm) reduced power by 33%. Completely covering the air cathode with a solid plate did not eliminate power generation, indicating oxygen leakage into the reactor. The S1.5 spacer slightly increased columbic efficiencies (from 20% to 24%) as a result of reduced oxygen transfer into the system. Based on operating conditions (1000ς, CE=20%), it was estimated that 0.9Lh -1 of air would be needed for 1m 2 of cathode area suggesting active air flow may be needed for larger scale MFCs. © 2012 Elsevier Ltd.

Exergy analysis and optimisation of a marine molten carbonate fuel cell system in simple and combined cycle configuration

International Nuclear Information System (INIS)

Dimopoulos, George G.; Stefanatos, Iason C.; Kakalis, Nikolaos M.P.

2016-01-01

Highlights: • Process modelling and optimisation of an integrated marine MCFC system. • Component-level and spatially distributed exergy analysis and balances. • Optimal simple cycle MCFC system with 45.5% overall exergy efficiency. • Optimal combined cycle MCFC system with 60% overall exergy efficiency. • Combined cycle MCFC system yields 30% CO_2 relative emissions reduction. - Abstract: In this paper we present the exergy analysis and design optimisation of an integrated molten carbonate fuel cell (MCFC) system for marine applications, considering waste heat recovery options for additional power production. High temperature fuel cells are attractive solutions for marine energy systems, as they can significantly reduce gaseous emissions, increase efficiency and facilitate the introduction of more environmentally-friendly fuels, like LNG and biofuels. We consider an already installed MCFC system onboard a sea-going vessel, which has many tightly integrated sub-systems and components: fuel delivery and pre-reforming, internal reforming sections, electrochemical conversion, catalytic burner, air supply and high temperature exhaust gas. The high temperature exhaust gasses offer significant potential for heat recovery that can be directed into both covering the system’s auxiliary heat requirements and power production. Therefore, an integrated systems approach is employed to accurately identify the true sources of losses in the various components and to optimise the overall system with respect to its energy efficiency, taking into account the various trade-offs and subject to several constraints. Here, we present a four-step approach: a. dynamic process models development of simple and combined-cycle MCFC system; b. MCFC components and system models calibration via onboard MCFC measurements; c. exergy analysis, and d. optimisation of the simple and combined-cycle systems with respect to their exergetic performance. Our methodology is based on the

Nickel catalysts for internal reforming in molten carbonate fuel cells

NARCIS (Netherlands)

Berger, R.J.; Berger, R.J.; Doesburg, E.B.M.; Doesburg, E.B.M.; van Ommen, J.G.; Ross, J.R.H.; Ross, J.R.H.

1996-01-01

Natural gas may be used instead of hydrogen as fuel for the molten carbonate fuel cell (MCFC) by steam reforming the natural gas inside the MCFC, using a nickel catalyst (internal reforming). The severe conditions inside the MCFC, however, require that the catalyst has a very high stability. In

Polymer coatings as separator layers for microbial fuel cell cathodes

KAUST Repository

Watson, Valerie J.

2011-03-01

Membrane separators reduce oxygen flux from the cathode into the anolyte in microbial fuel cells (MFCs), but water accumulation and pH gradients between the separator and cathode reduces performance. Air cathodes were spray-coated (water-facing side) with anion exchange, cation exchange, and neutral polymer coatings of different thicknesses to incorporate the separator into the cathode. The anion exchange polymer coating resulted in greater power density (1167 ± 135 mW m-2) than a cation exchange coating (439 ± 2 mW m-2). This power output was similar to that produced by a Nafion-coated cathode (1114 ± 174 mW m-2), and slightly lower than the uncoated cathode (1384 ± 82 mW m-2). Thicker coatings reduced oxygen diffusion into the electrolyte and increased coulombic efficiency (CE = 56-64%) relative to an uncoated cathode (29 ± 8%), but decreased power production (255-574 mW m-2). Electrochemical characterization of the cathodes ex situ to the MFC showed that the cathodes with the lowest charge transfer resistance and the highest oxygen reduction activity produced the most power in MFC tests. The results on hydrophilic cathode separator layers revealed a trade off between power and CE. Cathodes coated with a thin coating of anion exchange polymer show promise for controlling oxygen transfer while minimally affecting power production. © 2010 Elsevier B.V. All rights reserved.

2013 Estorm - Invited Paper - Cathode Materials Review

Energy Technology Data Exchange (ETDEWEB)

Daniel, Claus [ORNL; Mohanty, Debasish [ORNL; Li, Jianlin [ORNL; Wood III, David L [ORNL

2014-01-01

The electrochemical potential of cathode materials defines the positive side of the terminal voltage of a battery. Traditionally, cathode materials are the energy-limiting or voltage-limiting electrode. One of the first electrochemical batteries, the voltaic pile invented by Alessandro Volta in 1800 (Phil. Trans. Roy. Soc. 90, 403 431) had a copper-zinc galvanic element with a terminal voltage of 0.76 V. Since then, the research community has increased capacity and voltage for primary (nonrechargeable) batteries and round-trip efficiency for secondary (rechargeable) batteries. Successful secondary batteries have been the lead acid with a lead oxide cathode and a terminal voltage of 2.1 V and later the NiCd with a nickel(III) oxide hydroxide cathode and a 1.2 V terminal voltage. The relatively low voltage of those aqueous systems and the low round-trip efficiency due to activation energies in the conversion reactions limited their use. In 1976, Wittingham (J. Electrochem. Soc., 123, 315) and Besenhard (J Power Sources 1(3), 267) finally enabled highly reversible redox reactions by intercalation of lithium ions instead of by chemical conversion. In 1980, Goodenough and Mizushima (Mater. Res. Bull. 15, 783 789) demonstrated a high-energy and high-power LiCoO2 cathode, allowing for an increase of terminal voltage far beyond 3 V. Over the past four decades, the international research community has further developed cathode materials of many varieties. Current state-of-the-art cathodes demonstrate voltages beyond any known electrolyte stability window, bringing electrolyte research once again to the forefront of battery research.

Measuring current emission and work functions of large thermionic cathodes

International Nuclear Information System (INIS)

Fortgang, C.M.

2001-01-01

As one component of the nations Stockpile Stewardship program, Los Alamos National Laboratory is constructing a 20 MeV, 2 kA (with a 4 kA upgrade capability), 3ps induction linac for doing x-ray radiography of explosive devices. The linac is one leg of a facility called the Dual-Axis Radiography Hydrodynamic Test Facility (DARHT). The electron gun is designed to operate at 3.2 MV. The gun is a Pierce type design and uses a 6.5' cathode for 2 kA operation and an 8' cathode for 4 kA operation. We have constructed a small facility called the Cathode Test Stand (CTS) to investigate engineering and physics issues regarding large thermionic dispenser-cathodes. In particular, we have looked at the issues of temperature uniformity on the cathode surface and cathode quality as measured by its work function. We have done thermal imaging of both 8' and 6.5' cathodes. Here we report on measurements of the cathode work function, both the average value and how it vanes across the face of the cathode.

Hollow Cathode Assembly Development for the HERMeS Hall Thruster

Science.gov (United States)

Sarver-Verhey, Timothy R.; Kamhawi, Hani; Goebel, Dan M.; Polk, James E.; Peterson, Peter Y.; Robinson, Dale A.

2016-01-01

To support the operation of the HERMeS 12.5 kW Hall Thruster for NASA's Asteroid Redirect Robotic Mission, hollow cathodes using emitters based on barium oxide impregnate and lanthanum hexaboride are being evaluated through wear-testing, performance characterization, plasma modeling, and review of integration requirements. This presentation will present the development approach used to assess the cathode emitter options. A 2,000-hour wear-test of development model Barium Oxide (BaO) hollow cathode is being performed as part of the development plan. Specifically this test is to identify potential impacts cathode emitter life during operation in the HERMeS thruster. The cathode was operated with a magnetic field-equipped anode that simulates the HERMeS hall thruster operating environment. Cathode discharge performance has been stable with the device accumulating 743 hours at the time of this report. Observed voltage changes are attributed to keeper surface condition changes during testing. Cathode behavior during characterization sweeps exhibited stable behavior, including cathode temperature. The details of the cathode assembly operation of the wear-test will be presented.

Three-dimensional graphene sheets with NiO nanobelt outgrowths for enhanced capacity and long term high rate cycling Li-ion battery anode material

Science.gov (United States)

Shi, Waipeng; Zhang, Yingmeng; Key, Julian; Shen, Pei Kang

2018-03-01

An efficient synthesis method to grow well attached NiO nanobelts from 3D graphene sheets (3DGS) is reported herein. Ni-ion exchanged resin provides the initial Ni reactant portion, which serves both as a catalyst to form 3DGS and then as a seeding agent to grow the NiO nanobelts. The macroporous structure of 3DGS provides NiO containment to achieve a high cycling stability of up to 445 mAh g-1 after 360 cycles (and >112% capacity retention after 515 cycles) at a high current density of 2 A g-1. With a 26.8 wt.% content of NiO on 3DGS, increases in specific and volumetric capacity were 41.6 and 75.7% respectively over that of 3DGS at matching current densities. Therefore, the seeded growth of NiO nanobelts from 3DGS significantly boosts volumetric capacity, while 3DGS enables high rate long term cycling of the NiO. The high rate cycling stability of NiO on 3DGS can be attributed to (i) good attachment and contact to the large surface of 3DGS, (ii) high electron conductivity and rapid Li-ion transfer (via the interconnected, highly conductive graphitized walls of 3DGS) and (iii) buffering void space in 3DGS to contain volume expansion of NiO during charge/discharge.

Iron-Treated NiO as a Highly Transparent p-Type Protection Layer for Efficient Si-Based Photoanodes

DEFF Research Database (Denmark)

Mei, Bastian Timo; Permyakova, Anastasia Aleksandrovna; Frydendal, Rasmus

2014-01-01

Sputter deposition of 50 nm thick NiO films on p+–n-Si and subsequent treatment in an Fe-containing electrolyte yielded highly transparent photoanodes capable of water oxidation (OER) in alkaline media (1 M KOH) with high efficiency and stability. The Fe treatment of NiO thin films enabled Si...

A política externa independente (PEI): antecedentes, apogeu e declínio

OpenAIRE

Manzur,Tânia Maria P. G.

2014-01-01

Este artigo analisa o período de 1961 a 1964, quando a sociedade brasileira vivenciou o processo de gestação, desenvolvimento, apogeu e declínio da Política Externa Independente (PEI). Na vigência das presidências de Jânio Quadros e, posteriormente, João Goulart, observa-se expressivo envolvimento da opinião pública com assuntos de política exterior, envolvimento esse que é fruto de um amálgama entre o populismo e o desenvolvimento e a disseminação dos meios de comunicação de massa, bem como ...

O cultivo de valores exemplares: "galeria dos patronos de escolas", de Antônio d’Ávila (1980-1989 - Exemplary values cultivation: "galeria dos patronos de escolas", by Antônio d´Ávila (1980-1989

Directory of Open Access Journals (Sweden)

Thabatha Aline Trevisan

2011-03-01

Full Text Available Resumo Com o objetivo de contribuir para a história da educação brasileira e para o campo da imprensa periódica pedagógica, apresentam-se resultados de pesquisas desenvolvidas por meio de abordagem histórica do tema, centradas em pesquisa documental e bibliográfica. Neste artigo, destacam-se a produção de biografias, uma contribuição do educador Antônio d´Ávila para o periódico Jornal dos Professores, publicação do Centro do Professorado Paulista (CPP. Os resultados enfatizam o que era levado em conta para a elaboração das biografias e a constituição da representação ideal de ser professor. Palavras-chave: imprensa pedagógica; biografia; Antônio d’Ávila; pesquisa histórica em educação.   EXEMPLARY VALUES CULTIVATION: "GALERIA DOS PATRONOS DE ESCOLAS", BY ANTÔNIO D´ÁVILA (1980-1989 Abstract In order to contribute for the comprehension of the History of Education in Brazil and to the research on pedagogical periodic press, they are presented the results of the research developed through the historical approach of the theme, focused on documented and bibliographic research. In this paper, the key feature is the production of biographies, a contribution from Antônio d´Ávila, an educator from São Paulo State, for the periodical Jornal dos Professores, published by the Centro do Professorado Paulista. The results emphasize what was taken into account in the making of biographies and what would be the ideal representation of being a teacher. Keywords: pedagogical press; biography, Antônio d´Ávila; historical research on education.   El CULTIVO DE VALORES EJEMPLARES: "GALERIA DE LOS PATRONOS DE ESCUELAS", DE ANTÔNIO D’ÁVILA (1980-1989 Resumen Con el objetivo de contribuir para la historia de la educación brasilera y para el campo de la imprensa periódica pedagógica, se presentan resultados de pesquisas desarrolladas por medio de un abordaje histórico del tema, centradas en pesquisa documental y bibliogr

RF Electron Gun with Driven Plasma Cathode

CERN Document Server

Khodak, Igor

2005-01-01

It's known that RF guns with plasma cathodes based on solid-state dielectrics are able to generate an intense electron beam. In this paper we describe results of experimental investigation of the single cavity S-band RF gun with driven plasma cathode. The experimental sample of the cathode based on ferroelectric ceramics has been designed. Special design of the cathode permits to separate spatially processes of plasma development and electron acceleration. It has been obtained at RF gun output electron beam with particle energy ~500 keV, pulse current of 4 A and pulse duration of 80 ns. Results of experimental study of beam parameters are referred in. The gun is purposed to be applied as the intense electron beam source for electron linacs.

A Transient Model for Fuel Cell Cathode-Water Propagation Behavior inside a Cathode after a Step Potential

Directory of Open Access Journals (Sweden)

Der-Sheng Chan

2010-04-01

Full Text Available Most of the voltage losses of proton exchange membrane fuel cells (PEMFC are due to the sluggish kinetics of oxygen reduction on the cathode and the low oxygen diffusion rate inside the flooded cathode. To simulate the transient flooding in the cathode of a PEMFC, a transient model was developed. This model includes the material conservation of oxygen, vapor, water inside the gas diffusion layer (GDL and micro-porous layer (MPL, and the electrode kinetics in the cathode catalyst layer (CL. The variation of hydrophobicity of each layer generated a wicking effect that moves water from one layer to the other. Since the GDL, MPL, and CL are made of composite materials with different hydrophilic and hydrophobic properties, a linear function of saturation was used to calculate the wetting contact angle of these composite materials. The balance among capillary force, gas/liquid pressure, and velocity of water in each layer was considered. Therefore, the dynamic behavior of PEMFC, with saturation transportation taken into account, was obtained in this study. A step change of the cell voltage was used to illustrate the transient phenomena of output current, water movement, and diffusion of oxygen and water vapor across the entire cathode.

Cathode erosion in high-current high-pressure arc

CERN Document Server

Nemchinsky, V A

2003-01-01

Cathode erosion rate was experimentally investigated for two types of arcs: one with tungsten cathode in nitrogen atmosphere and one with hafnium cathode in oxygen atmosphere. Conditions were typical for plasma arc cutting systems: gas pressure from 2 to 5 atm, arc current from 200 to 400 A, gas flow rate from 50 to 130 litre min sup - sup 1. It was found that the actual cathode evaporation rate G is much lower than G sub 0 , the evaporation rate that follows from the Hertz-Knudsen formula: G = nu G sub 0. The difference is because some of the evaporated particles return back to the cathode. For conditions of our experiments, the factor nu could be as low as 0.01. It was shown experimentally that nu depends strongly on the gas flow pattern close to the cathode. In particular, swirling the gas increases nu many times. To explain the influence of gas swirling, model calculations of gas flows were performed. These calculations revealed difference between swirling and non-swirling flows: swirling the gas enhances...

Structured electron beams from nano-engineered cathodes

Energy Technology Data Exchange (ETDEWEB)

Lueangaramwong, A. [NICADD, DeKalb; Mihalcea, D. [NICADD, DeKalb; Andonian, G. [RadiaBeam Tech.; Piot, P. [Fermilab

2017-03-07

The ability to engineer cathodes at the nano-scale have open new possibilities such as enhancing quantum eciency via surface-plasmon excitation, forming ultra-low-emittance beams, or producing structured electron beams. In this paper we present numerical investigations of the beam dynamics associated to this class of cathode in the weak- and strong-field regimes.We finally discuss the possible applications of some of the achievable cathode patterns when coupled with other phase space manipulations.

Pneumoperitônio pós-cesárea: relato de caso

OpenAIRE

Amorim,Melania Maria Ramos de; Spencer Netto,Fernando Antônio Campelo; Santos,Luiz Carlos; Mascarenhas,Everaldo; Katz,Leila

1998-01-01

A associação de pneumoperitônio, dor abdominal e íleo paralítico no período pós-operatório relaciona-se, na maioria dos casos, à perfuração de vísceras ocas. Os autores apresentam um caso de pós-operatório de cesariana por DPPNI em que a paciente evoluiu com importante distensão e dor abdominal. Realizada radiografia de tórax e abdome evidenciou-se importante dilatação das alças de intestino grosso e delgado e pneumoperitônio, foi submetida a laparotomia exploradora com a hipótese diagnóstica...

Template synthesis and characterization of nanostructured hierarchical mesoporous ribbon-like NiO as high performance electrode material for supercapacitor

International Nuclear Information System (INIS)

Yao, Mingming; Hu, Zhonghua; Xu, Zijie; Liu, Yafei; Liu, Peipei; Zhang, Qiang

2015-01-01

The ribbon-like NiO was synthesized by a hard-template method combining the calcination, using mesoporous carbon as a hard templat and guanidine hydrochloride as precipitant of weak base, respectively. The nanostructured hierarchical mesoporous ribbon-like NiO exhibits the high specific capacitance of 1260 F g −1 at the current density of 1 A g −1 , and 95% capacity retention at a current density of 10 A g −1 in a testing range of 5000 cycles. - Highlights: • Ribbon-like NiO was prepared by using mesoporous carbon as a hard template. • Typical ribbon-like NiO possesses the hierarchical mesoporous nanostructure. • High specific capacitance of 1260 F g −1 is obtained at a current density of 1 A g −1 . • Excellent electrochemical stability of 95% after 5000 charge–discharge cycles. - Abstract: In this paper, nanostructured hierarchical mesoporous ribbon-like NiO was synthesized by a hard-template method combining the calcination process. Nickel sulfate hexahydrate, guanidine hydrochloride and mesoporous carbon were used as nickel precursors, precipitant of weak base and template, respectively. The resultant NiO samples were characterized by Raman spectroscopy, energy dispersive spectrometer, X-ray diffraction, N 2 adsorption and desorption, scanning electron microscopy and transmission electron microscopy. The electrochemical performances were evaluated by cyclic voltammetry (CV), cyclic chronopotentiometry (CP) and electrochemical impedance spectroscopy (EIS) in 6 M KOH solution. The typical hierarchical mesoporous ribbon-like NiO shows a good electrochemical performance: a high specific capacitance of 1260 F g −1 at 1 A g −1 , 748 F g −1 at high current density of 20 A g −1 and 95% capacity retention at a current density of 10 A g −1 in a testing range of 5000 cycles

Effect of Various Solvent on the Synthesis of NiO Nanopowders by Simple Sol-Gel Methods and Its Characterization

Directory of Open Access Journals (Sweden)

Sherly Kasuma Warda Ningsih

2015-03-01

Full Text Available Synthesis of nickel oxide (NiO with various solvents by simple sol-gel process has been done. NiO nanopowders were obtained by using nickel nitrate hexahydrate and sodium hydroxide 5 M were used as precursor and agent precipitator, respectively. The addition of various solvents that used in this research were aquadest, methanol and isopropanol. The powders were formed by drying in the temperature of 100-110 °C for 1 h and after heating at ±450 °C for 1 h. The products were obtained black powders. The products were characterized by Energy Dispersive X-Ray Fluorescence (ED-XRF, X-Ray Diffraction (XRD and Scanning Electron Microscopy (SEM. The ED-XRF pattern show that composition of NiO produced was 96.9%. The XRD patterns showed NiO forms were in monoclinic structure with aquadest solvent and cubic structure with methanol and isopropanol used. Crystal sizes of NiO particles produced with aquadest, methanol, isopropanol were obtained in the range 37.05; 72.16; 66.04 nm respectively. SEM micrograph clearly showed that powder had a spherical shape with uniform distribution size is 0.1-1.0 µm approximately.

Synthesis and characterization of n-type NiO:Al thin films for fabrication of p-n NiO homojunctions

Science.gov (United States)

Sun, Hui; Liao, Ming-Han; Chen, Sheng-Chi; Li, Zhi-Yue; Lin, Po-Chun; Song, Shu-Mei

2018-03-01

n-type NiO:Al thin films were deposited by RF magnetron sputtering. Their optoelectronic properties versus Al target power was investigated. The results show that with increasing Al target power, the conduction type of NiO films changes from p-type to n-type. The variation of the film’s electrical and optical properties depends on Al amount in the film. When Al target power is relatively low, Al3+ cations tend to enter nickel vacancy sites, which makes the lattice structure of NiO more complete. This improves the carrier mobility and film’s transmittance. However, when Al target power exceeds 40 W, Al atoms begin to enter into interstitial sites and form an Al cluster in the NiO film. This behavior is beneficial for improving the film’s n-type conductivity but degrades the film’s transmittance. Finally, Al/(p-type NiO)/(n-type NiO:Al)/ITO homojunctions were fabricated. Their performance was compared with Al/(p-type NiO)/ITO heterojunctions without an n-type NiO layer. Thanks to the better interface quality between the two NiO layers, the homojunctions present better performance.

Plasma-induced field emission study of carbon nanotube cathode

Directory of Open Access Journals (Sweden)

Yi Shen

2011-10-01

Full Text Available An investigation on the plasma-induced field emission (PFE properties of a large area carbon nanotube (CNT cathode on a 2 MeV linear induction accelerator injector is presented. Experimental results show that the cathode is able to emit intense electron beams. Intense electron beams of 14.9–127.8  A/cm^{2} are obtained from the cathode. The CNT cathode desorbs gases from the CNTs during the PFE process. The fast cathode plasma expansion affects the diode perveance. The amount of outgassing is estimated to be 0.06–0.49  Pa·L, and the ratio of outgassing and electron are roughly calculated to be within the range of 170–350 atoms per electron. The effect of the outgassing is analyzed, and the outgassing mass spectrum of the CNT cathode has been studied during the PFE. There is a significant desorption of CO_{2}, N_{2}(CO, and H_{2} gases, which plays an important role during the PFE process. All the experiments demonstrate that the outgassing plays an important role in the formation of the cathode plasma. Moreover, the characteristic turn-on time of the CNT cathode was measured to be 39 ns.

Cathode refunctionalization as a lithium ion battery recycling alternative

Science.gov (United States)

Ganter, Matthew J.; Landi, Brian J.; Babbitt, Callie W.; Anctil, Annick; Gaustad, Gabrielle

2014-06-01

An approach to battery end-of-life (EOL) management is developed involving cathode refunctionalization, which enables remanufacturing of the cathode from EOL materials to regain the electrochemical performance. To date, the optimal end-of-life management of cathode materials is based on economic value and environmental impact which can influence the methods and stage of recycling. Traditional recycling methods can recover high value metal elements (e.g. Li, Co, Ni), but still require synthesis of new cathode from a mix of virgin and recovered materials. Lithium iron phosphate (LiFePO4) has been selected for study as a representative cathode material due to recent mass adoption and limited economic recycling drivers due to the low inherent cost of iron. Refunctionalization of EOL LiFePO4 cathode was demonstrated through electrochemical and chemical lithiation methods where the re-lithiated LiFePO4 regained the original capacity of 150-155 mAh g-1. The environmental impact of the new recycling technique was determined by comparing the embodied energy of cathode material originating from virgin, recycled, and refunctionalized materials. The results demonstrate that the LiFePO4 refunctionalization process, through chemical lithiation, decreases the embodied energy by 50% compared to cathode production from virgin materials.

Surface Characterization of the LCLS RF Gun Cathode

International Nuclear Information System (INIS)

Brachmann, Axel; Decker, Franz-Josef; Ding, Yuantao; Dowell, David; Emma, Paul; Frisch, Josef; Gilevich, Sasha; Hays, Gregory; Hering, Philippe; Huang, Zhirong; Iverson, Richard; Loos, Henrik; Miahnahri, Alan; Nordlund, Dennis; Nuhn, Heinz-Dieter; Pianetta, Piero; Turner, James; Welch, James; White, William; Wu, Juhao; Xiang, Dao

2012-01-01

The first copper cathode installed in the LCLS RF gun was used during LCLS commissioning for more than a year. However, after high charge operation (> 500 pC), the cathode showed a decline of quantum efficiency within the area of drive laser illumination. They report results of SEM, XPS and XAS studies that were carried out on this cathode after it was removed from the gun. X-ray absorption and X-ray photoelectron spectroscopy reveal surface contamination by various hydrocarbon compounds. In addition they report on the performance of the second installed cathode with emphasis on the spatial distribution of electron emission.

Development of a pH sensor using nanoporous nanostructures of NiO.

Science.gov (United States)

Ibupoto, Z H; Khun, K; Willander, M

2014-09-01

Glass is the conventional material used in pH electrodes to monitor pH in various applications. However, the glass-based pH electrode has some limitations for particular applications. The glass sensor is limited in the use of in vivo biomedical, clinical or food applications because of the brittleness of glass, its large size, the difficulty in measuring small volumes and the absence of deformation (inflexibility). Nanostructure-based pH sensors are very sensitive, reliable, fast and applicable towards in vivo measurements. In this study, nanoporous NiO nanostructures are synthesized on a gold-coated glass substrate by a hydrothermal route using poly(vinyl alcohol) (PVA) as a stabilizer. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) techniques were used for the morphological and crystalline studies. The grown NiO nanostructures are uniform and dense, and they possess good crystallinity. A pH sensor based on these NiO nanostructures was developed by testing the different pH values from 2-12 of phosphate buffered saline solution. The proposed pH sensor showed robust sensitivity of -43.74 ± 0.80 mV/pH and a quick response time of less than 10 s. Moreover, the repeatability, reproducibility and stability of the presented pH sensor were also studied.

Cathode protection for underground steel tanks

International Nuclear Information System (INIS)

Angelovski, Zoran

1998-01-01

Cathodic protection of underground petroleum storage tanks and piping systems is acceptable for both economic and ecological reasons. With out the cathodic protection of underground steel reservoirs, short time after the exploitation, there was a bore as a result of underground corrosion. The bore causes ecological consequences and at the same time its repair needs big investments. Furthermore, there are great number of tanks placed near cities, so in the future this problem needs a special attention in order to preserve ecological surrounding. The topic of this paper is underground corrosion as well as cathodic protection of steel tanks for oil derivatives storage. (author)

Evaluation of gasification and gas cleanup processes for use in molten carbonate fuel cell power plants. Final report. [Contains lists and evaluations of coal gasification and fuel gas desulfurization processes

Energy Technology Data Exchange (ETDEWEB)

Jablonski, G.; Hamm, J.R.; Alvin, M.A.; Wenglarz, R.A.; Patel, P.

1982-01-01

This report satisfies the requirements for DOE Contract AC21-81MC16220 to: List coal gasifiers and gas cleanup systems suitable for supplying fuel to molten carbonate fuel cells (MCFC) in industrial and utility power plants; extensively characterize those coal gas cleanup systems rejected by DOE's MCFC contractors for their power plant systems by virtue of the resources required for those systems to be commercially developed; develop an analytical model to predict MCFC tolerance for particulates on the anode (fuel gas) side of the MCFC; develop an analytical model to predict MCFC anode side tolerance for chemical species, including sulfides, halogens, and trace heavy metals; choose from the candidate gasifier/cleanup systems those most suitable for MCFC-based power plants; choose a reference wet cleanup system; provide parametric analyses of the coal gasifiers and gas cleanup systems when integrated into a power plant incorporating MCFC units with suitable gas expansion turbines, steam turbines, heat exchangers, and heat recovery steam generators, using the Westinghouse proprietary AHEAD computer model; provide efficiency, investment, cost of electricity, operability, and environmental effect rankings of the system; and provide a final report incorporating the results of all of the above tasks. Section 7 of this final report provides general conclusions.

Plínio Marcos: uma biografia

OpenAIRE

Contiero, Lucinéia [UNESP

2007-01-01

Esta é uma biografia de Plínio Marcos, dramaturgo santista nascido em 1935. Tem um pouco de biografia intelectual, um pouco de biografia crítica. Mas é sobretudo a vida de um homem de teatro. O trabalho se abre com uma discussão teórica, em face da qual procuro situar essa abordagem de uma vida. Como toda biografia, prevaleceu aqui o interesse pela disposição cronológica dos fatos, com paradas para tratar de certos aspectos importantes, a vida de jornalista, a peças de maior sucesso. No prime...

Oxide Fiber Cathode Materials for Rechargeable Lithium Cells

Science.gov (United States)

Rice, Catherine E.; Welker, Mark F.

2008-01-01

LiCoO2 and LiNiO2 fibers have been investigated as alternatives to LiCoO2 and LiNiO2 powders used as lithium-intercalation compounds in cathodes of rechargeable lithium-ion electrochemical cells. In making such a cathode, LiCoO2 or LiNiO2 powder is mixed with a binder [e.g., poly(vinylidene fluoride)] and an electrically conductive additive (usually carbon) and the mixture is pressed to form a disk. The binder and conductive additive contribute weight and volume, reducing the specific energy and energy density, respectively. In contrast, LiCoO2 or LiNiO2 fibers can be pressed and sintered to form a cathode, without need for a binder or a conductive additive. The inter-grain contacts of the fibers are stronger and have fewer defects than do those of powder particles. These characteristics translate to increased flexibility and greater resilience on cycling and, consequently, to reduced loss of capacity from cycle to cycle. Moreover, in comparison with a powder-based cathode, a fiber-based cathode is expected to exhibit significantly greater ionic and electronic conduction along the axes of the fibers. Results of preliminary charge/discharge-cycling tests suggest that energy densities of LiCoO2- and LiNiO2-fiber cathodes are approximately double those of the corresponding powder-based cathodes.

Study of the hollow cathode plasma electron-gun

International Nuclear Information System (INIS)

Zhang Yonghui; Jiang Jinsheng; Chang Anbi

2003-01-01

For developing a novel high-current, long pulse width electron source, the theoretics and mechanism of the hollow cathode plasma electron-gun are analyzed in detail in this paper, the structure and the physical process of hollow cathode plasma electron-gun are also studied. This gun overcomes the limitations of most high-power microwave tubes, which employ either thermionic cathodes that produce low current-density beams because of the limitation of the space charge, or field-emission cathodes that offer high current density but provide only short pulse width because of plasma closure of the accelerating gap. In the theories studying on hollow cathode plasma electron-gun, the characteristic of the hollow-cathode discharge is introduced, the action during the forming of plasma of the stimulating electrode and the modulating anode are discussed, the movement of electrons and ions and the primary parameters are analyzed, and the formulas of the electric field, beam current density and the stabilization conditions of the beam current are also presented in this paper. The numerical simulation is carried out based on Poisson's equation, and the equations of current continuity and movement. And the optimized result is reported. On this basis, we have designed a hollow-cathode-plasma electron-gun, whose output pulse current is 2 kA, and pulse width is 1 microsecond

Pre-acclimation of a wastewater inoculum to cellulose in an aqueous–cathode MEC improves power generation in air–cathode MFCs

KAUST Repository

Cheng, Shaoan

2011-01-01

Cellulose has been used in two-chamber microbial fuel cells (MFCs), but power densities were low. Higher power densities can be achieved in air-cathode MFCs using an inoculum from a two-chamber, aqueous-cathode microbial electrolysis cell (MEC). Air-cathode MFCs with this inoculum produced maximum power densities of 1070mWm-2 (cathode surface area) in single-chamber and 880mWm-2 in two-chamber MFCs. Coulombic efficiencies ranged from 25% to 50%, and COD removals were 50-70% based on total cellulose removals of 60-80%. Decreasing the reactor volume from 26 to 14mL (while maintaining constant electrode spacing) decreased power output by 66% (from 526 to 180mWm-2) due to a reduction in total mass of cellulose added. These results demonstrate that air-cathode MFCs can produce high power densities with cellulose following proper acclimation of the inoculum, and that organic loading rates are important for maximizing power densities from particulate substrates. © 2010 Elsevier Ltd.

Influence of reduction conditions of NiO on its mechanical and electrical properties

Directory of Open Access Journals (Sweden)

Yehor Brodnikovskyi

2016-04-01

Full Text Available Yttria stabilized zirconia with a nickel catalyst (Ni-YSZ is the most developed, widely used cermet anode for manufacturing Solid Oxide Fuel Cells (SOFCs. Its electro-catalytic properties, mechanical durability and performance stability in hydrogen-rich environ­ments makes it the state of the art fuel electrode for SOFCs. During the reduction stage in initial SOFC operation, the virgin anode material, a NiO-YSZ mixture, is reduced to Ni-YSZ. The volume decrease associated with the change from NiO-YSZ to Ni-YSZ creates voids and causes structural changes, which can influence the physical properties of the anode. In this work, the structural, mechanical and electrical properties of NiO samples before and after reduction in pure H2 and a mixture of 5 vol. % H2-Ar were studied. The NiO to Ni phase transformations that occur in the anode under reducing and Reduction-Oxidation (RedOx cycling conditions and the impact on cell microstruc­ture, strength and electrical conductivity have been examined. Results show that the RedOx treatment of the NiO samples influence on their properties controversially, due to structural transfor­mation (formation of large amount of fine pores of the reduced Ni. It strengthened the treated samples yielding the highest mechanical strength values of 25.7 MPa, but from another side it is resulting in lowest electrical conductivity value of 1.9×105 S m-1 among all reduced samples. The results of this investigation shows that reduction conditions of NiO is a powerful tool for influence on properties of the anode substrate.

The effect of cathode surface impurities on gap closure

International Nuclear Information System (INIS)

Hinshelwood, D.D.

1983-01-01

Gap closure due to cathode (or anode) plasma motion is often the principal limitation on the pulse length of intense beam diodes and magnetically insulated transmission lines. Since the plasma expansion velocity is typically on the order of the sound speed, a high atomic number plasma is desirable. In recent experiments performed on a Sandia Nereus accelerator (240kV, 50kA, 3-30kA/cm 2 , 70ns) with a parallel plate diode, the cathode plasma was seen to be composed of both the cathode substrate material and constituents (hydrogen and carbon) of surface contaminants such as pump oils. The plasma expansion velocities, inferred from impedance measurements, were 1.5-2 cm/μs and were the same for carbon, aluminum and stainless steel cathodes. This similarity, combined with the temperature estimates of 2-3eV obtained from spectroscopy, implied that the expansion was due to protons from surface contaminants. Similar results were reported from studies of ablatively driven plasmas. In a continuation of the work, the results of time and spatially resolved spectroscopic studies of plasma formed on aluminum cathodes, yielding measurements of the expansion velocities of different components of the cathode plasma, are presented. We have heated stainless steel cathodes in situ to 700 0 C. The Hα line emission was seen to decrease by more than an order of magnitude (becoming lost in the background) when the cathodes were heated but no change in the impedance behavior was observed. Evidently the heating was insufficient to remove the last monolayer, which should contain more than enough hydrogen to close the gap. Preliminary experiments with gold-plated cathodes (which should be more resistant to chemisorption) yielded similar results. Further measurements of plasma formed on heated cathodes are presented

Direct Electrochemistry of Horseradish Peroxidase on NiO Nanoflower Modified Electrode and Its Electrocatalytic Activity

Directory of Open Access Journals (Sweden)

Lijun Yan

2016-09-01

Full Text Available In this paper nickel oxide (NiO nanoflower was synthesized and used for the realization of direct electrochemistry of horseradish peroxidase (HRP. By using carbon ionic liquid electrode (CILE as the substrate electrode, NiO-HRP composite was casted on the surface of CILE with chitosan (CTS as the film forming material and the modified electrode was denoted as CTS/NiO-HRP/CILE. UV-Vis absorption and FT-IR spectra confirmed that HRP retained its native structure after mixed with NiO nanoflower. Direct electron transfer of HRP on the modified electrode was investigated by cyclic voltammetry with a pair of quasi-reversible redox waves appeared, indicating that the presence of NiO nanoflower on the electrode surface could accelerate the electron transfer rate between the electroactive center of HRP and the substrate electrode. Electrochemical behaviors of HRP on the modified electrode were carefully investigated. The HRP modified electrode showed excellent electrocatalytic activity to the reduction of trichloroacetic acid with wider linear range and lower detection limit. Therefore the presence of NiO nanoflower could provide a friendly biocompatible interface for immobilizing biomolecules and keeping their native structure. The fabricated electrochemical biosensor displayed the advantages such as high sensitivity, good reproducibility and long-term stability. This work is licensed under a Creative Commons Attribution 4.0 International License.

Solution-Processible Crystalline NiO Nanoparticles for High-Performance Planar Perovskite Photovoltaic Cells.

Science.gov (United States)

Kwon, Uisik; Kim, Bong-Gi; Nguyen, Duc Cuong; Park, Jong-Hyeon; Ha, Na Young; Kim, Seung-Joo; Ko, Seung Hwan; Lee, Soonil; Lee, Daeho; Park, Hui Joon

2016-07-28

In this work, we report on solution-based p-i-n-type planar-structured CH3NH3PbI3 perovskite photovoltaic (PV) cells, in which precrystallized NiO nanoparticles (NPs) without post-treatment are used to form a hole transport layer (HTL). X-ray diffraction and high-resolution transmission electron microscopy showed the crystallinity of the NPs, and atomic force microscopy and scanning electron microscopy confirmed the uniform surfaces of the resultant NiO thin film and the subsequent perovskite photoactive layer. Compared to the conventional poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) ( PSS) HTL, the NiO HTL had excellent energy-level alignment with that of CH3NH3PbI3 and improved electron-blocking capability, as analyzed by photoelectron spectroscopy and diode modeling, resulting in Voc ~0.13 V higher than conventional PSS-based devices. Consequently, a power conversion efficiency (PCE) of 15.4% with a high fill factor (FF, 0.74), short-circuit current density (Jsc, 20.2 mA·cm(-2)), and open circuit voltage (Voc, 1.04 V) having negligible hysteresis and superior air stability has been achieved.

Os intelectuais e a defesa da preservação do patrimônio em Porto Alegre (1970)

OpenAIRE

Maria Angélica Zubaran

2017-01-01

Este estudo analisa as narrativas em defesa da preservação e salvaguarda do patrimônio histórico da cidade de Porto Alegre na imprensa local, na década de 1970. Investiga-se o discurso dos "intelectuais do patrimônio" e os novos valores, significados e usos que atribuíram ao patrimônio histórico da cidade, na luta pela sua preservação e salvaguarda. O foco deste artigo é as narrativas do jornalista Alberto André e do historiador Sérgio da Costa Franco e suas múltiplas representações de memóri...

Synchrotron Investigations of SOFC Cathode Degradation

Energy Technology Data Exchange (ETDEWEB)

Idzerda, Yves

2013-09-30

The atomic variations occurring in cathode/electrolyte interface regions of La{sub 1-x}Sr{sub x}Co{sub y}Fe{sub 1-y}O{sub 3-δ} (LSCF) cathodes and other SOFC related materials have been investigated and characterized using soft X-ray Absorption Spectroscopy (XAS) and diffuse soft X-ray Resonant Scattering (XRS). X-ray Absorption Spectroscopy in the soft X-ray region (soft XAS) is shown to be a sensitive technique to quantify the disruption that occurs and can be used to suggest a concrete mechanism for the degradation. For LSC, LSF, and LSCF films, a significant degradation mechanism is shown to be Sr out-diffusion. By using the XAS spectra of hexavalent Cr in SrCrO4 and trivalent Cr in Cr2O3, the driving factor for Sr segregation was identified to be the oxygen vacancy concentration at the anode and cathode side of of symmetric LSCF/GDC/LSCF heterostructures. This is direct evidence of vacancy induced cation diffusion and is shown to be a significant indicator of cathode/electrolyte interfacial degradation. X-ray absorption spectroscopy is used to identify the occupation of the A-sites and B-sites for LSC, LSF, and LSCF cathodes doped with other transition metals, including doping induced migration of Sr to the anti-site for Sr, a significant cathode degradation indicator. By using spatially resolved valence mapping of Co, a complete picture of the surface electrochemistry can be determined. This is especially important in identifying degradation phenomena where the degradation is spatially localized to the extremities of the electrochemistry and not the average. For samples that have electrochemical parameters that are measured to be spatially uniform, the Co valence modifications were correlated to the effects of current density, overpotential, and humidity.

Reducing DRIFT backgrounds with a submicron aluminized-mylar cathode

Science.gov (United States)

Battat, J. B. R.; Daw, E.; Dorofeev, A.; Ezeribe, A. C.; Fox, J. R.; Gauvreau, J.-L.; Gold, M.; Harmon, L.; Harton, J.; Lafler, R.; Landers, J.; Lauer, R. J.; Lee, E. R.; Loomba, D.; Lumnah, A.; Matthews, J.; Miller, E. H.; Mouton, F.; Murphy, A. St. J.; Paling, S. M.; Phan, N.; Sadler, S. W.; Scarff, A.; Schuckman, F. G.; Snowden-Ifft, D.; Spooner, N. J. C.; Walker, D.

2015-09-01

Background events in the DRIFT-IId dark matter detector, mimicking potential WIMP signals, are predominantly caused by alpha decays on the central cathode in which the alpha particle is completely or partially absorbed by the cathode material. We installed a 0.9 μm thick aluminized-mylar cathode as a way to reduce the probability of producing these backgrounds. We study three generations of cathode (wire, thin-film, and radiologically clean thin-film) with a focus on the ratio of background events to alpha decays. Two independent methods of measuring the absolute alpha decay rate are used to ensure an accurate result, and agree to within 10%. Using alpha range spectroscopy, we measure the radiologically cleanest cathode version to have a contamination of 3.3±0.1 ppt 234U and 73±2 ppb 238U. This cathode reduces the probability of producing an RPR from an alpha decay by a factor of 70±20 compared to the original stainless steel wire cathode. First results are presented from a texturized version of the cathode, intended to be even more transparent to alpha particles. These efforts, along with other background reduction measures, have resulted in a drop in the observed background rate from 500/day to 1/day. With the recent implementation of full-volume fiducialization, these remaining background events are identified, allowing for background-free operation.

Escultura em madeira em Laranjeiras/SE: Perspectivas do patrimônio material e imaterial no século XXI

Directory of Open Access Journals (Sweden)

Janaina Cardoso de Mello

2015-10-01

Full Text Available O trabalho traça o panorama conceitual e prático do “patrimônio material” e “patrimônio imaterial”, em suas intercessões, no contexto da cidade de Laranjeiras em Sergipe. A metodologia utiliza a entrevista gravada, semi-estruturada, com Demar (Ademar, escultor em madeira, cuja produção cria, expõe e comercializa no Centro de Artesanato, agraciado com o título de “patrimônio vivo” pela Prefeitura. Com a alta tecnologia, a Arqueologia Pública deve ir às comunidades, ouvir suas demandas para compartilhar de informações, registro e conservação do patrimônio cultural que congrega em si características de seu modus vivendi, valorizando a diversidade e a sobrevivência da arte. Como referência os trabalhos de Sandra Pelegrini, Pedro Paulo Funari, UNESCO, IPHAN e Ana Carla Reis.

RF Photoelectric injectors using needle cathodes

International Nuclear Information System (INIS)

Lewellen, J.W.; Brau, C.A.

2003-01-01

Photocathode RF guns, in various configurations, are the injectors of choice for both current and future applications requiring high-brightness electron beams. Many of these applications, such as single-pass free-electron lasers, require beams with high brilliance but not necessarily high charge per bunch. Field-enhanced photoelectric emission has demonstrated electron-beam current density as high as 10 10 A/m 2 , with a quantum efficiency in the UV that approaches 10% at fields on the order of 10 10 V/m. Thus, the use of even a blunt needle holds promise for increasing cathode quantum efficiency without sacrificing robustness. We present an initial study on the use of needle cathodes in photoinjectors to enhance beam brightness while reducing beam charge. Benefits include lower drive-laser power requirements, easier multibunch operation, lower emittance, and lower beam degradation due to charge-dependent effects in the postinjector accelerator. These benefits result from a combination of a smaller cathode emission area, greatly enhanced RF field strength at the cathode, and the charge scaling of detrimental postinjector linac effects, e.g., transverse wakefields and CSR

RF Photoelectric injectors using needle cathodes

Science.gov (United States)

Lewellen, J. W.; Brau, C. A.

2003-07-01

Photocathode RF guns, in various configurations, are the injectors of choice for both current and future applications requiring high-brightness electron beams. Many of these applications, such as single-pass free-electron lasers, require beams with high brilliance but not necessarily high charge per bunch. Field-enhanced photoelectric emission has demonstrated electron-beam current density as high as 10 10 A/m 2, with a quantum efficiency in the UV that approaches 10% at fields on the order of 10 10 V/m. Thus, the use of even a blunt needle holds promise for increasing cathode quantum efficiency without sacrificing robustness. We present an initial study on the use of needle cathodes in photoinjectors to enhance beam brightness while reducing beam charge. Benefits include lower drive-laser power requirements, easier multibunch operation, lower emittance, and lower beam degradation due to charge-dependent effects in the postinjector accelerator. These benefits result from a combination of a smaller cathode emission area, greatly enhanced RF field strength at the cathode, and the charge scaling of detrimental postinjector linac effects, e.g., transverse wakefields and CSR.

Functionally Graded Cathodes for Solid Oxide Fuel Cells

International Nuclear Information System (INIS)

Lei Yang; Ze Liu; Shizhone Wang; Jaewung Lee; Meilin Liu

2008-01-01

The main objective of this DOE project is to demonstrate that the performance and long-term stability of the state-of-the-art LSCF cathode can be enhanced by a catalytically active coating (e.g., LSM or SSC). We have successfully developed a methodology for reliably evaluating the intrinsic surface catalytic properties of cathode materials. One of the key components of the test cell is a dense LSCF film, which will function as the current collector for the electrode material under evaluation to eliminate the effect of ionic and electronic transport. Since it is dense, the effect of geometry would be eliminated as well. From the dependence of the electrode polarization resistance on the thickness of a dense LSCF electrode and on partial pressure of oxygen, we have confirmed that the surface catalytic activity of LSCF limits the performances of LSCF-based cathodes. Further, we have demonstrated, using test cells of different configurations, that the performance of LSCF-based electrodes can be significantly enhanced by infiltration of a thin film of LSM or SSC. In addition, the stability of LSCF-based cathodes was also improved by infiltration of LSM or SSC. While the concept feasibility of the electrode architecture is demonstrated, many details are yet to be determined. For example, it is not clear how the surface morphology, composition, and thickness of the coatings change under operating conditions over time, how these changes influence the electrochemical behavior of the cathodes, and how to control the microscopic details of the coatings in order to optimize the performance. The selection of the catalytic materials as well as the detailed microstructures of the porous LSCF and the catalyst layer may critically impact the performance of the proposed cathodes. Further, other fundamental questions still remain; it is not clear why the degradation rates of LSCF cathodes are relatively high, why a LSM coating improves the stability of LSCF cathodes, which catalysts

Hydrogen Gas Sensing Characteristics of Nanostructured NiO Thin Films Synthesized by SILAR Method

Science.gov (United States)

Karaduman, Irmak; Çorlu, Tugba; Yıldırım, M. Ali; Ateş, Aytunç; Acar, Selim

2017-07-01

Nanostructured NiO thin films have been synthesized by a facile, low-cost successive ionic layer adsorption and reaction (SILAR) method, and the effects of the film thickness on their hydrogen gas sensing properties investigated. The samples were characterized by scanning electron microscopy (SEM), x-ray diffraction (XRD) analysis, and energy-dispersive x-ray analysis. The XRD results revealed that the crystallinity improved with increasing thickness, exhibiting polycrystalline structure. SEM studies showed that all the films covered the glass substrate well. According to optical absorption measurements, the optical bandgap decreased with increasing film thickness. The gas sensing properties of the nanostructured NiO thin films were studied as a function of operating temperature and gas concentration. The samples showed good sensing performance of H2 gas with high response. The maximum response was 75% at operating temperature of 200°C for hydrogen gas concentration of 40 ppm. These results demonstrate that nanostructured NiO thin films synthesized by the SILAR method have potential for application in hydrogen detection.

Controlled synthesis of mesoporous β-Ni(OH)2 and NiO nanospheres with enhanced electrochemical performance

International Nuclear Information System (INIS)

Xing, Shengtao; Wang, Qian; Ma, Zichuan; Wu, Yinsu; Gao, Yuanzhe

2012-01-01

Highlights: ► Uniform mesoporous β-Ni(OH) 2 and NiO nanospheres with hierarchical structures were synthesized by a simple complexation–precipitation method. ► Both ammonia and citrate played an important role for the formation of mesoporous nanospheres. ► β-Ni(OH) 2 and NiO nanospheres showed excellent capacitive properties due to their mesoporous structures and larger surface areas. -- Abstract: Uniform mesoporous β-Ni(OH) 2 and NiO nanospheres with hierarchical structures were synthesized by a facile complexation–precipitation method. The effects of ammonia and citrate on the structure and morphology of the products were thoroughly investigated by X-ray powder diffraction, scanning electron microscopy, transmission electron microscopy and nitrogen adsorption–desorption measurements. The results indicated that ammonia played an important role for the formation of flowerlike spheres assembled from nanosheets. The addition of citrate could remarkably reduce the particle sizes and increase the specific surface areas of flowerlike spheres. A possible formation mechanism based on the experimental results was proposed to understand their growing procedures. β-Ni(OH) 2 and NiO nanospheres prepared with the addition of citrate showed excellent capacitive properties due to their mesoporous structures and large surface areas, suggesting the importance of controlled synthesis of hierarchical nanostructures for their applications.

Post-Removal Examination of GTF Cathode No.2

International Nuclear Information System (INIS)

Kirby, R.

2005-01-01

This photo-cathode (PC), GTF Cathode No.2, was removed from the GTF in October, 2000. It was characterized in September, 1999 by G. Mulhollan and me (Report entitled ''A Brief Report on a Brief Examination of the Electropolished GTF Cathode'', LCLS-TN-99-10). The cathode conditions and results of that exam were: (1) The cathode was conventionally machined and cleaned in the SLAC Plating Shop. (2) The machining process left a central defect (400 microns diameter) which was not removed by electropolishing. (3) The electropolished surface was ''orange-peeled'', typical of excessive polishing. (4) Secondary electron microscopy (SEM) examination showed numerous 10 micron-diameter etch pits and a small number of copper surface particles. Operation of this cathode in the GTF exhibited ''holloW--beam'' behavior, suggesting that the central defect may have been responsible for non-normal emergence of the photo-emitted beam. No laser cleaning of the cathode was done, so all arc features are due to breakdowns. Post-removal analysis consisted of loW--magnification digital camera pictures (taken with glancing-incidence tungsten white light illumination, to emphasize particles/pitting) and SEM. All images are available in digital (TIFF) form. Also available is a Power Point presentation of the results. Contact me for either. These image files are high-resolution and, thus, large in size. A 200K loW--resolution contact sheet of a few images is attached to this report. Images are referred to by file name

Tailored Core Shell Cathode Powders for Solid Oxide Fuel Cells

Energy Technology Data Exchange (ETDEWEB)

Swartz, Scott [NexTech Materials, Ltd.,Lewis Center, OH (United States)

2015-03-23

In this Phase I SBIR project, a “core-shell” composite cathode approach was evaluated for improving SOFC performance and reducing degradation of lanthanum strontium cobalt ferrite (LSCF) cathode materials, following previous successful demonstrations of infiltration approaches for achieving the same goals. The intent was to establish core-shell cathode powders that enabled high performance to be obtained with “drop-in” process capability for SOFC manufacturing (i.e., rather than adding an infiltration step to the SOFC manufacturing process). Milling, precipitation and hetero-coagulation methods were evaluated for making core-shell composite cathode powders comprised of coarse LSCF “core” particles and nanoscale “shell” particles of lanthanum strontium manganite (LSM) or praseodymium strontium manganite (PSM). Precipitation and hetero-coagulation methods were successful for obtaining the targeted core-shell morphology, although perfect coverage of the LSCF core particles by the LSM and PSM particles was not obtained. Electrochemical characterization of core-shell cathode powders and conventional (baseline) cathode powders was performed via electrochemical impedance spectroscopy (EIS) half-cell measurements and single-cell SOFC testing. Reliable EIS testing methods were established, which enabled comparative area-specific resistance measurements to be obtained. A single-cell SOFC testing approach also was established that enabled cathode resistance to be separated from overall cell resistance, and for cathode degradation to be separated from overall cell degradation. The results of these EIS and SOFC tests conclusively determined that the core-shell cathode powders resulted in significant lowering of performance, compared to the baseline cathodes. Based on the results of this project, it was concluded that the core-shell cathode approach did not warrant further investigation.

Improved Rare-Earth Emitter Hollow Cathode

Science.gov (United States)

Goebel, Dan M.

2011-01-01

An improvement has been made to the design of the hollow cathode geometry that was created for the rare-earth electron emitter described in Compact Rare Earth Emitter Hollow Cathode (NPO-44923), NASA Tech Briefs, Vol. 34, No. 3 (March 2010), p. 52. The original interior assembly was made entirely of graphite in order to be compatible with the LaB6 material, which cannot be touched by metals during operation due to boron diffusion causing embrittlement issues in high-temperature refractory materials. Also, the graphite tube was difficult to machine and was subject to vibration-induced fracturing. This innovation replaces the graphite tube with one made out of refractory metal that is relatively easy to manufacture. The cathode support tube is made of molybdenum or molybdenum-rhenium. This material is easily gun-bored to near the tolerances required, and finish machined with steps at each end that capture the orifice plate and the mounting flange. This provides the manufacturability and robustness needed for flight applications, and eliminates the need for expensive e-beam welding used in prior cathodes. The LaB6 insert is protected from direct contact with the refractory metal tube by thin, graphite sleeves in a cup-arrangement around the ends of the insert. The sleeves, insert, and orifice plate are held in place by a ceramic spacer and tungsten spring inserted inside the tube. To heat the cathode, an insulating tube is slipped around the refractory metal hollow tube, which can be made of high-temperature materials like boron nitride or aluminum nitride. A screw-shaped slot, or series of slots, is machined in the outside of the ceramic tube to constrain a refractory metal wire wound inside the slot that is used as the heater. The screw slot can hold a single heater wire that is then connected to the front of the cathode tube by tack-welding to complete the electrical circuit, or it can be a double slot that takes a bifilar wound heater with both leads coming out

Electrospinning synthesis of 3D porous NiO nanorods as anode material for lithium-ion batteries

Directory of Open Access Journals (Sweden)

Wei Kong Xiang

2016-06-01

Full Text Available Three-dimensional NiO nanorods were synthesized as anode material by electrospinning method. X-ray diffraction results revealed that the product sintered at 400 °C had impure metallic nickel phase which, however, became pure NiO phase as the sintering temperature rose. Nevertheless, the nanorods sintered at 400, 500 and 600 °C had similar diameters (∼200 nm.The NiO nanorod material sintered at 500 °C was chip-shaped with a diameter of 200 nm and it exhibited a porous 3D structure. The nanorod sintered at 500 °C had the optimal electrochemical performance. Its discharge specific capacity was 1127 mAh·g−1 initially and remained as high as 400 mAh·g−1 at a current density of 55 mA·g−1 after 50 cycles.

Síntese e caracterização de vermiculita mesoporosa obtida por modificação com sais complexos de alumínio e lantânio

Directory of Open Access Journals (Sweden)

M. V. S. Fernandes

2014-06-01

Full Text Available Os estudos de aumento do espaçamento interplanar basal, distribuição de poros e área superficial de uma argila mesoporosa obtida a partir de vermiculita precursora, foram realizados por intercalação de oligômero poli-hidroxi catiônico Al13 e um misto (La xAl13-x obtido por dopagem com lantânio, seguida de calcinação para formação dos pilares. As caracterizações das amostras foram feitas por difração de raios X, espectroscopia Mössbauer, ressonância magnética nuclear do estado sólido (27Al MAS-NMR e isotermas de N2 (BET. A presença de lantânio na estrutura da vermiculita resultou no aumento de sua área e de porosidade.

Ultra High Energy Density Cathodes with Carbon Nanotubes

Science.gov (United States)

2013-12-10

a) Carbon nanotube paper coated with NCA cathode composite for testing as positive electrode in Li-ion battery (b) Comparison of NCA specific...received and purified CNT electrodes coated with NCA cathode composite. (b) Discharge capacities as a function of rate and cycle for NCA on Al and...thickness increases. The first approach was to cast SOA NCA cathode composites onto CNT current collectors using an adjustable blade coater. The

Controlled p-type to n-type conductivity transformation in NiO thin films by ultraviolet-laser irradiation

Energy Technology Data Exchange (ETDEWEB)

Gupta, Pranav; Dutta, Titas; Mal, Siddhartha; Narayan, Jagdish [Materials Science and Engineering, North Carolina State University, Raleigh, North Carolina 27606 (United States)

2012-01-01

We report the systematic changes in structural, electrical, and optical properties of NiO thin films on c-sapphire introduced by nanosecond ultraviolet excimer laser pulses. Epitaxial nature of as deposited NiO was determined by x-ray diffraction phi scans and transmission electron microscopy (TEM) and it was established that NiO film growth takes place with twin domains on sapphire where two types of domains have 60 deg. in-plane rotation with respect to each other about the [111] growth direction. We determined that at pulsed laser energy density of 0.275 J/cm{sup 2}, NiO films exhibited conversion from p-type semiconducting to n-type conductive behavior with three orders of magnitude decrease in resistivity, while maintaining its cubic crystal structure and good epitaxial relationship. Our TEM and electron-energy-loss spectroscopy studies conclusively ruled out the presence of any Ni clustering or precipitation due to the laser treatment. The laser-induced n-type carrier transport and conductivity enhancement were shown to be reversible through subsequent thermal annealing in oxygen. This change in conductivity behavior was correlated with the nonequilibrium concentration of laser induced Ni{sup 0}-like defect states.

Preparation, ferromagnetic and photocatalytic performance of NiO and hollow Co{sub 3}O{sub 4} fibers through centrifugal-spinning technique

Energy Technology Data Exchange (ETDEWEB)

Feng, Cong; Lin, Xuejun; Wang, Xinqiang, E-mail: xqwang@sdu.edu.cn; Liu, Hongjing; Liu, Benxue; Zhu, Luyi; Zhang, Guanghui; Xu, Dong

2016-02-15

Highlights: • NiO and hollow Co{sub 3}O{sub 4} fibers with the diameter of about 10 μm were prepared through centrifugal-spinning technique. • The evolution mechanism from precursor to crystalline fibers was explored. • Both NiO and hollow Co{sub 3}O{sub 4} fibers show ferromagnetism. • The NiO fibers exhibit good photocatalytic performance. - Abstract: Both NiO and hollow Co{sub 3}O{sub 4} fibers with the diameter of about 10 μm have been successfully prepared through spinning high viscous sols into precursor fibers and followed calcination process. The evolution process from precursor to crystalline fibers and the microstructures of the obtained fibers were characterized by TG-DSC, FT-IR, XRD, HRTEM, SEM and the like. The method is facile and cost-effective for mass production of fibers and the obtained fibers are pure phase with high crystallinity. Their magnetic properties were investigated, showing that both the fibers are ferromagnetic. Meanwhile, the NiO fibers exhibit good photocatalytic performance for the removal of Congo red from water under UV light irradiation.

Hollow Cathode Studies for the Next Generation Ion Engines in JAXA

Science.gov (United States)

Ohkawa, Yasushi; Hayakawa, Yukio; Yoshida, Hideki; Miyazaki, Katsuhiro; Kitamura, Shoji; Kajiwara, Kenichi

The current status of experimental studies of hollow cathodes for the next-generation ion engines in the Aerospace Research and Development Directorate, JAXA is described. One of the topics on the hollow cathode studies is a life test of a discharge cathode. The keeper disk, orifice plate, and cathode tube of this discharge cathode are made of "high density graphite," which possesses much higher tolerance to ion impingement compared with conventional metal materials. The life test had started in March 2006 and the cumulative operation time reached 15,600 hours in April 2008. No severe degradation has been found both in the operation voltages and electrodes so far, and the test is favorably in progress. In addition to the life test of the discharge cathode, some experiments for design optimization of neutralizer cathodes have been performed. A life test of the neutralizer cathode is being started in June 2008.

Performance Enhancement of Small Molecular Solar Cells by Bilayer Cathode Buffer.

Science.gov (United States)

Sun, Qinjun; Zhao, Huanbin; Zhou, Miao; Gao, Liyan; Hao, Yuying

2016-04-01

An effective composite bilayer cathode buffer structure is proposed for use in small molecular solar cells. CsF was doped in Alq3 to form the first cathode buffer, leading to small serial resistances. BCP was used as the second cathode buffer to block the holes to the electrode. The optimized bilayer cathode buffer significantly increased the short circuit and fill factor of devices. By integrating this bilayer cathode buffer, the CuPc/C60 small molecular heterojunction cell exhibited a power conversion efficiency of up to 0.8%, which was an improvement of 56% compared to a device with only the Alq3 cathode buffer. Meanwhile, the bilayer cathode buffer still has a good protective effect on the performance of the device.

Fabrication and characterization of NiO thin films prepared by SILAR method

International Nuclear Information System (INIS)

Akaltun, Yunus; Çayır, Tuba

2015-01-01

Highlights: • NiO thin films have been deposited on glass substrates using SILAR method for the first time. • The electron effective mass, refractive index were calculated by using the energy bandgap values. • The effect of film thickness on the structural, optical and electrical properties were studied. • The bandgap values of the films decreased from 3.71 to 3.67 eV. - Abstract: NiO thin films were synthesised on glass substrates at room temperature using the Successive Ionic Layer Adsorption and Reaction (SILAR) method. The effect of film thickness on the structural, morphological, optical and electrical properties of NiO thin films was investigated. The X-ray diffraction (XRD) and scanning electron microscopy (SEM) studies showed that all the films exhibit polycrystalline structure are covered well with glass substrates. The crystalline and surface properties of the films improved with increasing film thickness. The energy band gap values were decreased from 3.71 to 3.67 eV depending on the film thickness. The refractive index (n), optical static (ε o ) and high frequency dielectric constant (ε ∞ ) values were calculated by using the energy band gap values as a function of the film thickness. The resistivity of the films varied between 4.1 and 802.1 Ω cm with increasing film thickness at room temperature

Fabrication and characterization of NiO thin films prepared by SILAR method

Energy Technology Data Exchange (ETDEWEB)

Akaltun, Yunus [Department of Electrical and Electronic Engineering, Erzincan University, 24100 Erzincan (Turkey); Çayır, Tuba [Department of Biomedical Engineering, Erzincan University, 24100 Erzincan (Turkey)

2015-03-15

Highlights: • NiO thin films have been deposited on glass substrates using SILAR method for the first time. • The electron effective mass, refractive index were calculated by using the energy bandgap values. • The effect of film thickness on the structural, optical and electrical properties were studied. • The bandgap values of the films decreased from 3.71 to 3.67 eV. - Abstract: NiO thin films were synthesised on glass substrates at room temperature using the Successive Ionic Layer Adsorption and Reaction (SILAR) method. The effect of film thickness on the structural, morphological, optical and electrical properties of NiO thin films was investigated. The X-ray diffraction (XRD) and scanning electron microscopy (SEM) studies showed that all the films exhibit polycrystalline structure are covered well with glass substrates. The crystalline and surface properties of the films improved with increasing film thickness. The energy band gap values were decreased from 3.71 to 3.67 eV depending on the film thickness. The refractive index (n), optical static (ε{sub o}) and high frequency dielectric constant (ε{sub ∞}) values were calculated by using the energy band gap values as a function of the film thickness. The resistivity of the films varied between 4.1 and 802.1 Ω cm with increasing film thickness at room temperature.

Análise metalográfica do titânio puro submetido à soldagem laser Nd: YAG e TIG

Directory of Open Access Journals (Sweden)

Ana Cláudia Gabrielli Piveta

Full Text Available INTRODUÇÃO: Os métodos de soldagem mais utilizados em Odontologia não podem ser aplicados ao titânio puro e às suas ligas em função da alta reatividade do titânio com elementos atmosféricos; dessa forma, o mesmo não deve ser soldado por processo comum. OBJETIVO: O objetivo deste trabalho foi avaliar a característica metalúrgica do titânio comercialmente puro sem solda e submetido aos processos de soldagem a laser e TIG. MATERIAL E MÉTODO: Foram confeccionados 15 corpos de prova em titânio comercialmente puro, cinco para cada condição, na forma de hastes cilíndricas, obtidas por fundição odontológica, sob atmosfera de gás argônio e vácuo, com calor produzido por um arco voltaico, com a injeção do titânio sob vácuo-pressão. Três grupos foram formados I: soldagem a laser; II: soldagem TIG, e III: sem solda. Os corpos de prova do grupo I e II foram seccionados ao meio e soldados por TIG e por laser, respectivamente; o grupo III foi mantido sem corte e sem solda, como controle. A análise metalográfica foi realizada sob aumentos de 50×, 100× e 200×, em microscópio. RESULTADO: Pelos resultados obtidos nas micrografias, o titânio comercialmente puro apresentou uma morfologia de grãos equiaxiais da fase α, o cordão de solda a laser apresentou estrutura martensítica e, na TIG, microestrutura Widmanstätten. CONCLUSÃO: A microestrutura martensítica é condizente com a alta taxa de resfriamento proveniente do processo de soldagem a laser. As estruturas martensítica e Widmansttäten são mais refinadas quando comparadas à microestrutura do metal base.

Rare earth oxide doping in oxide cathodes

International Nuclear Information System (INIS)

Engelsen, Daniel den; Gaertner, Georg

2006-01-01

The effect on life performance and poisoning with O 2 by doping oxide cathodes with rare earth oxides and pseudo rare earth oxides, notably yttria, is qualitatively explained in terms of electrolysis of BaO during emission of electrons. Doped cathodes show less electrolysis and consume therefore less Ba during life: consequently, doped cathodes have a better life performance. However, the lower Ba-production makes doped cathodes more sensitive to oxygen poisoning. The experimentally found relation between conductivity and yttria concentration was the motive to propose a new model for the crystal imperfections in BaO. In this new imperfection model most Y 3+ -ions will combine with barium vacancies, therefore, the increase of the conductivity is modest and also the effect on the position of the Fermi level is modest. By assuming a combination of bulk and surface conductivity, the agreement between experiment and theory can be improved further

TPC cathode read-out with C-pads

International Nuclear Information System (INIS)

Janik, R.; Pikna, M.; Sitar, B.; Strmen, P.; Szarka, I.

2009-01-01

A Time Projection Chamber with 'C' like shaped cathode pads was built and tested. It offers a low gas gain operation, a good pulse shape and a lightweight construction. The Pad Response Function (PRF), the cathode to anode pulse height ratios and the pad pulse shapes of the C-pad structure were measured and compared with planar cathode structures in two different wire geometries. The cathode to anode signal ratio was improved from between 0.2 and 0.4 up to 0.7. The PRF was considerably improved, it has a Gaussian shape and is narrower than in the case of the planar pads. The pulse shape from the C-pad read-out is similar to the pulse shape from a detector with a cylindrical shape of electrodes. A method for aluminum pad mass production based on a precise cold forging was developed and tested.

Geiger counters of gamma rays with a bismuth cathode

International Nuclear Information System (INIS)

Meunier, R.; Legrand, J.P.

1953-01-01

Geiger Muller counters present a lake of efficiency of some per cent, for the γ radiations. In the region 0,3 - 1 MeV, a substantial growth of their output can be obtained by a special construction of their cathode. In accordance with previous works, we constructed some counter of formed cathode by a pleated copper wire fencing covered of Bi by electrolysis. The successive modifications brought to a cylindrical conventional cathode in sheet metal of copper, that succeeds to this type of cathode, drive to an improvement of the output. (M.B.) [fr

Methanol-Tolerant Cathode Catalyst Composite For Direct Methanol Fuel Cells

Science.gov (United States)

Zhu, Yimin; Zelenay, Piotr

2006-03-21

A direct methanol fuel cell (DMFC) having a methanol fuel supply, oxidant supply, and its membrane electrode assembly (MEA) formed of an anode electrode and a cathode electrode with a membrane therebetween, a methanol oxidation catalyst adjacent the anode electrode and the membrane, an oxidant reduction catalyst adjacent the cathode electrode and the membrane, comprises an oxidant reduction catalyst layer of a platinum-chromium alloy so that oxidation at the cathode of methanol that crosses from the anode through the membrane to the cathode is reduced with a concomitant increase of net electrical potential at the cathode electrode.

Pipelines cathodic protection design methodologies for impressed ...

African Journals Online (AJOL)

Several inadequate designs of cathodically polarized offshore and onshore pipelines have been reported in Nigeria owing to design complexity and application of the cathodic protection system. The present study focused on critical and detailed approach in impressed current and sacrificial anode design calculation ...

Numerical study on rectangular microhollow cathode discharge

International Nuclear Information System (INIS)

He Shoujie; Ouyang Jiting; He Feng; Li Shang

2011-01-01

Rectangular microhollow cathode discharge in argon is investigated by using two-dimensional time-dependent self-consistent fluid model. The electric potential, electric field, particle density, and mean electron energy are calculated. The results show that hollow cathode effect can be onset in the present configuration, with strong electric field and high mean electron energy in the cathode fall while high density and quasineutral plasma in the negative glow. The potential well and electric filed reversal are formed in the negative glow region. It is suggested that the presence of large electron diffusion flux necessitates the field reversal and potential well.

Plasma distribution of cathodic ARC deposition system

International Nuclear Information System (INIS)

Anders, S.; Raoux, S.; Krishnan, K.; MacGill, R.A.; Brown, I.G.

1996-01-01

The plasma distribution using a cathodic arc plasma source with and without magnetic macroparticle filter has been determined by depositing on a transparent plastic substrate and measuring the film absorption. It was found that the width of the distribution depends on the arc current, and it also depends on the cathode material which leads to a spatial separation of the elements when an alloy cathode is used. By applying a magnetic multicusp field near the exit of the magnetic filter, it was possible to modify the plasma distribution and obtain a flat plasma profile with a constant and homogeneous elemental distribution

Cyclotron resonance in a cathode ray tube

International Nuclear Information System (INIS)

Gherbanovschi, N.; Tanasa, M.; Stoican, O.

2002-01-01

Absorption of the RF energy by the electron beam in a cathode ray tube due to the cyclotron resonance is described. The cathode ray tube is placed within a Helmholtz coils system supplied by a sawtooth current generator. In order to generate RF field and to detect RF absorption a gate dip-meter equipped with a FET transistor is used. The bias voltage variations of the FET transistors as a function of the magnetic field are recorded. The operating point of the cathode ray tube has been chosen so that the relaxation oscillations of the detection system can be observed. (authors)

Investigations Of A Pulsed Cathodic Vacuum Arc

Science.gov (United States)

Oates, T. W. H.; Pigott, J.; Denniss, P.; Mckenzie, D. R.; Bilek, M. M. M.

2003-06-01

Cathodic vacuum arcs are well established as a method for producing thin films for coatings and as a source of metal ions. Research into DC vacuum arcs has been going on for over ten years in the School of Physics at the University of Sydney. Recently a project was undertaken in the school to design and build a pulsed CVA for use in the investigation of plasma sheaths and plasma immersion ion implantation. Pulsed cathodic vacuum arcs generally have a higher current and plasma density and also provide a more stable and reproducible plasma density than their DC counterparts. Additionally it has been shown that if a high repetition frequency can be established the deposition rate of pulsed arcs is equal to or greater than that of DC arcs with a concomitant reduction in the rate of macro-particle formation. We present here results of our investigations into the building of a center-triggered pulsed cathodic vacuum arc. The design of the power supply and trigger mechanism and the geometry of the anode and cathode are examined. Observations of type I and II arc spots using a CCD camera, and cathode spot velocity dependence on arc current will be presented. The role of retrograde motion in a high current pulsed arc is discussed.

Investigations Of A Pulsed Cathodic Vacuum Arc

International Nuclear Information System (INIS)

Oates, T.W.H.; Pigott, J.; Denniss, P.; Mckenzie, D.R.; Bilek, M.M.M.

2003-01-01

Cathodic vacuum arcs are well established as a method for producing thin films for coatings and as a source of metal ions. Research into DC vacuum arcs has been going on for over ten years in the School of Physics at the University of Sydney. Recently a project was undertaken in the school to design and build a pulsed CVA for use in the investigation of plasma sheaths and plasma immersion ion implantation. Pulsed cathodic vacuum arcs generally have a higher current and plasma density and also provide a more stable and reproducible plasma density than their DC counterparts. Additionally it has been shown that if a high repetition frequency can be established the deposition rate of pulsed arcs is equal to or greater than that of DC arcs with a concomitant reduction in the rate of macro-particle formation. We present here results of our investigations into the building of a center-triggered pulsed cathodic vacuum arc. The design of the power supply and trigger mechanism and the geometry of the anode and cathode are examined. Observations of type I and II arc spots using a CCD camera, and cathode spot velocity dependence on arc current will be presented. The role of retrograde motion in a high current pulsed arc is discussed

Neutral hydrophilic cathode catalyst binders for microbial fuel cells

KAUST Repository

Saito, Tomonori

2011-01-01

Improving oxygen reduction in microbial fuel cell (MFC) cathodes requires a better understanding of the effects of the catalyst binder chemistry and properties on performance. A series of polystyrene-b-poly(ethylene oxide) (PS-b-PEO) polymers with systematically varying hydrophilicity were designed to determine the effect of the hydrophilic character of the binder on cathode performance. Increasing the hydrophilicity of the PS-b-PEO binders enhanced the electrochemical response of the cathode and MFC power density by ∼15%, compared to the hydrophobic PS-OH binder. Increased cathode performance was likely a result of greater water uptake by the hydrophilic binder, which would increase the accessible surface area for oxygen reduction. Based on these results and due to the high cost of PS-b-PEO, the performance of an inexpensive hydrophilic neutral polymer, poly(bisphenol A-co-epichlorohydrin) (BAEH), was examined in MFCs and compared to a hydrophilic sulfonated binder (Nafion). MFCs with BAEH-based cathodes with two different Pt loadings initially (after 2 cycles) had lower MFC performance (1360 and 630 mW m-2 for 0.5 and 0.05 mg Pt cm-2) than Nafion cathodes (1980 and 1080 mW m -2 for 0.5 and 0.05 mg Pt cm-2). However, after long-term operation (22 cycles, 40 days), power production of each cell was similar (∼1200 and 700-800 mW m-2 for 0.5 and 0.05 mg Pt cm-2) likely due to cathode biofouling that could not be completely reversed through physical cleaning. While binder chemistry could improve initial electrochemical cathode performance, binder materials had less impact on overall long-term MFC performance. This observation suggests that long-term operation of MFCs will require better methods to avoid cathode biofouling. © 2011 The Royal Society of Chemistry.

Efficient photoelectrochemical water splitting by a doping-controlled GaN photoanode coated with NiO cocatalyst

International Nuclear Information System (INIS)

Kang, Jin-Ho; Kim, Soo Hee; Ebaid, Mohamed; Lee, June Key; Ryu, Sang-Wan

2014-01-01

Efficient photoelectrochemical (PEC) water splitting was demonstrated by a doping-controlled GaN photoanode coated with NiO cocatalyst. Highly doped n-GaN was sandwiched between undoped GaN layers to effectively collect electrons through ohmic contact. With zero external bias, the photocurrent density of the optimized doping profile was ∼3.5 times higher than that of the undoped GaN reference. However, the increased doping concentration degraded the photoanode stability, which was attributed to crystalline defects generated in the highly doped n-GaN. NiO cocatalyst improved the long-term stability of the photoanode because of GaN/NiO band alignment, enhancing hole transport into NiO and suppressing PEC corrosion mediated by hole crowding in GaN. This work established a design strategy for increasing the photocurrent as well as improving stability during water splitting with a GaN-based photoanode

Barium depletion in hollow cathode emitters

International Nuclear Information System (INIS)

Polk, James E.; Mikellides, Ioannis G.; Katz, Ira; Capece, Angela M.

2016-01-01

Dispenser hollow cathodes rely on a consumable supply of Ba released by BaO-CaO-Al 2 O 3 source material in the pores of a tungsten matrix to maintain a low work function surface. The examination of cathode emitters from long duration tests shows deposits of tungsten at the downstream end that appear to block the flow of Ba from the interior. In addition, a numerical model of Ba transport in the cathode plasma indicates that the Ba partial pressure in the insert may exceed the equilibrium vapor pressure of the dominant Ba-producing reaction, and it was postulated previously that this would suppress Ba loss in the upstream part of the emitter. New measurements of the Ba depletion depth from a cathode insert operated for 8200 h reveal that Ba loss is confined to a narrow region near the downstream end, confirming this hypothesis. The Ba transport model was modified to predict the depletion depth with time. A comparison of the calculated and measured depletion depths gives excellent qualitative agreement, and quantitative agreement was obtained assuming an insert temperature 70 °C lower than measured beginning-of-life values

PARA ALÉM DO CENTRO HISTÓRICO: VALORES E SENTIDOS DO PATRIMÔNIO CULTURAL EDIFICADO DE SANTA MARIA/RS

OpenAIRE

Manuela Ilha Silva

2015-01-01

A apropriação do Patrimônio Cultural por uma comunidade é pressuposto para que ele exista como elemento que ratifica memórias e histórias e, especialmente, faça sentido para determinado grupo social. Para transcender a condição de materialidade e passe a ter significações que não acabam em si mesma, no caso do patrimônio de caráter material, a edificação deve ser detentora de valores culturalmente atribuídos que a façam identificável como patrimônio. A partir desta colocação, s...

Air-cathode structure optimization in separator-coupled microbial fuel cells

KAUST Repository

Zhang, Xiaoyuan

2011-12-01

Microbial fuel cells (MFC) with 30% wet-proofed air cathodes have previously been optimized to have 4 diffusion layers (DLs) in order to limit oxygen transfer into the anode chamber and optimize performance. Newer MFC designs that allow close electrode spacing have a separator that can also reduce oxygen transfer into the anode chamber, and there are many types of carbon wet-proofed materials available. Additional analysis of conditions that optimize performance is therefore needed for separator-coupled MFCs in terms of the number of DLs and the percent of wet proofing used for the cathode. The number of DLs on a 50% wet-proofed carbon cloth cathode significantly affected MFC performance, with the maximum power density decreasing from 1427 to 855mW/m 2 for 1-4 DLs. A commonly used cathode (30% wet-proofed, 4 DLs) produced a maximum power density (988mW/m 2) that was 31% less than that produced by the 50% wet-proofed cathode (1 DL). It was shown that the cathode performance with different materials and numbers of DLs was directly related to conditions that increased oxygen transfer. The coulombic efficiency (CE) was more affected by the current density than the oxygen transfer coefficient for the cathode. MFCs with the 50% wet-proofed cathode (2 DLs) had a CE of >84% (6.8A/m 2), which was substantially larger than that previously obtained using carbon cloth air-cathodes lacking separators. These results demonstrate that MFCs constructed with separators should have the minimum number of DLs that prevent water leakage and maximize oxygen transfer to the cathode. © 2011 Elsevier B.V.

Cathode power distribution system and method of using the same for power distribution

Science.gov (United States)

Williamson, Mark A; Wiedmeyer, Stanley G; Koehl, Eugene R; Bailey, James L; Willit, James L; Barnes, Laurel A; Blaskovitz, Robert J

2014-11-11

Embodiments include a cathode power distribution system and/or method of using the same for power distribution. The cathode power distribution system includes a plurality of cathode assemblies. Each cathode assembly of the plurality of cathode assemblies includes a plurality of cathode rods. The system also includes a plurality of bus bars configured to distribute current to each of the plurality of cathode assemblies. The plurality of bus bars include a first bus bar configured to distribute the current to first ends of the plurality of cathode assemblies and a second bus bar configured to distribute the current to second ends of the plurality of cathode assemblies.

Power generation by packed-bed air-cathode microbial fuel cells

KAUST Repository

Zhang, Xiaoyuan

2013-08-01

Catalysts and catalyst binders are significant portions of the cost of microbial fuel cell (MFC) cathodes. Many materials have been tested as aqueous cathodes, but air-cathodes are needed to avoid energy demands for water aeration. Packed-bed air-cathodes were constructed without expensive binders or diffusion layers using four inexpensive carbon-based materials. Cathodes made from activated carbon produced the largest maximum power density of 676±93mW/m2, followed by semi-coke (376±47mW/m2), graphite (122±14mW/m2) and carbon felt (60±43mW/m2). Increasing the mass of activated carbon and semi-coke from 5 to ≥15g significantly reduced power generation because of a reduction in oxygen transfer due to a thicker water layer in the cathode (~3 or ~6cm). These results indicate that a thin packed layer of activated carbon or semi-coke can be used to make inexpensive air-cathodes for MFCs. © 2013 Elsevier Ltd.

Reservoir Cathode for Electric Space Propulsion, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — We propose a hollow reservoir cathode to improve performance in ion and Hall thrusters. We will adapt our existing reservoir cathode technology to this purpose....

Explosive emission cathode on the base of carbon plastic fibre

International Nuclear Information System (INIS)

Korenev, S.A.; Baranov, A.M.; Kostyuchenko, S.V.; Chernenko, N.M.

1989-01-01

A fabrication process for explosive emission cathodes on the base of carbon plastic fibre of practically any geometrical shape and dimensions is developed. Experimental studies of electron beam current collection from cathodes, 2cm in diameter, at voltages across the diode of 10 and 150-250kV. It is shown that the ignition voltage for cathode plasma is ∼2kV at the interelectrode diode gap of 5mm and residual gas pressure of ∼5x10 -5 Torr. The carbon-fibre cathode, fabricated in this way, provides more stable current collection of an electron beam (without oscillations) than other cathodes

Surface studies of thermionic cathodes and the mechanism of operation of an impregnated tungsten cathode

International Nuclear Information System (INIS)

Forman, R.

1976-09-01

The surface properties of conventional impregnated cathodes were investigated by the use of Auger spectroscopy and work function measurements, and these were compared with a synthesized barium- or barium oxide coated tungsten surface. The barium- and barium oxide coated surfaces were prepared by evaporating barium onto a tungsten surface that can be heated to elevated temperatures. Multilayer or monolayer coverages can be investigated using this technique. The results of this study show that the surface of an impregnated tungsten cathode is identical to that observed for a synthesized monolayer or partial monolayer of barium on partially oxidized tungsten, using the criteria of identical Auger patterns and work functions. Desorption measurements of barium from a tungsten surface were also made. These results in conjunction with Auger and work function data were interpreted to show that throughout most of its life an impregnated cathode operating in the range of 1100 C has a partial monolayer rather than a monolayer of barium on its surface

Bond length variation in Zn substituted NiO studied from extended X-ray absorption fine structure

Science.gov (United States)

Singh, S. D.; Poswal, A. K.; Kamal, C.; Rajput, Parasmani; Chakrabarti, Aparna; Jha, S. N.; Ganguli, Tapas

2017-06-01

Bond length behavior for Zn substituted NiO is determined through extended x-ray absorption fine structure (EXAFS) measurements performed at ambient conditions. We report bond length value of 2.11±0.01 Å for Zn-O of rock salt (RS) symmetry, when Zn is doped in RS NiO. Bond length for Zn substituted NiO RS ternary solid solutions shows relaxed behavior for Zn-O bond, while it shows un-relaxed behavior for Ni-O bond. These observations are further supported by first-principles calculations. It is also inferred that Zn sublattice remains nearly unchanged with increase in lattice parameter. On the other hand, Ni sublattice dilates for Zn compositions up to 20% to accommodate increase in the lattice parameter. However, for Zn compositions more than 20%, it does not further dilate. It has been attributed to the large disorder that is incorporated in the system at and beyond 20% of Zn incorporation in the cubic RS lattice of ternary solid solutions. For these large percentages of Zn incorporation, the Ni and the Zn atoms re-arrange themselves microscopically about the same nominal bond length rather than systematically increase in magnitude to minimize the energy of the system. This results in an increase in the Debye-Waller factor with increase in the Zn concentration rather than a systematic increase in the bond lengths.

O Apolônio de Tiana da biografia escrita por Filóstrato e os sofistas

Directory of Open Access Journals (Sweden)

Semíramis Corsi Silva

2016-12-01

Full Text Available Flávio Filóstrato foi um sofista grego que desenvolveu sua produção escrita no Império Romano da dinastia dos Severos (193-235 d.C.. Suas obras mais conhecidas são os textos de natureza biográfica Vida de Apolônio de Tiana e Vidas dos sofistas. Percebemos nestas duas obras muitas semelhanças entre os sofistas e o filósofo e sábio pitagórico Apolônio de Tiana, que acreditamos ser uma espécie de projeção do autor e de seu grupo. Neste artigo buscaremos comparar o Apolônio filostratiano com alguns aspectos dos sofistas da obra Vidas dos sofistas e tecer algumas considerações sobre as práticas de Apolônio relatadas por Filóstrato, paralelamente à análise de práticas e características de alguns importantes escritores do Império Romano com tradição de sofistas: Apuleio, Dião de Prusa e Élio Aristides. Além das obras de Filóstrato, utilizaremos textos de Apuleio, Dião de Prusa e Élio Aristides, bem como trabalhos historiográficos sobre a temática.

Barium depletion study on impregnated cathodes and lifetime prediction

International Nuclear Information System (INIS)

Roquais, J.M.; Poret, F.; Doze, R. le; Ricaud, J.L.; Monterrin, A.; Steinbrunn, A.

2003-01-01

In the thermionic cathodes used in cathode ray-tubes (CRTs), barium is the key element for the electronic emission. In the case of the dispenser cathodes made of a porous tungsten pellet impregnated with Ba, Ca aluminates, the evaporation of Ba determines the cathode lifetime with respect to emission performance in the CRT. The Ba evaporation results in progressive depletion of the impregnating material inside the pellet. In the present work, the Ba depletion with time has been extensively characterized over a large range of cathode temperature. Calculations using the depletion data allowed modeling of the depletion as a function of key parameters. The link between measured depletion and emission in tubes has been established, from which an end-of-life criterion was deduced. Taking modeling into account, predicting accelerated life-tests were performed using high-density maximum emission current (MIK)

New doped tungsten cathodes. Applications to power grid tubes

International Nuclear Information System (INIS)

Cachard, J. de; Cadoret, K; Martinez, L.; Veillet, D.; Millot, F.

2001-01-01

Thermionic emission behavior of tungsten/tungsten carbide modified with rare earth (La, Ce, Y) oxides is examined on account of suitability to deliver important current densities in a thermo-emissive set up and for long lifetime. Work functions of potential cathodes have been determined from Richardson plots for La 2 O 3 doped tungsten and for tungsten covered with variable compositions rare earth tungstates. The role of platinum layers covering the cathode was also examined. Given all cathodes containing mainly lanthanum oxides were good emitters, emphasis was put on service lifetime. Comparisons of lifetime in tungsten doped with rare earth oxides and with rare earth tungstates show that microstructure of the operating cathodes may play the major role in the research of very long lifetime cathodes. Based on these results, tests still running show lifetime compatible with power grid tubes applications. (author)

Testing Iodine as a New Fuel for Cathodes

Science.gov (United States)

Glad, Harley; Branam, Richard; Rogers, Jim; Warren, Matthew; Burleson, Connor; Siy, Grace

2017-11-01

The objective of this research is to demonstrate the viability of using iodine as an alternative space propulsion propellant. The demonstration requires the testing of a cathode with xenon and then the desired element iodine. Currently, cathodes run on noble gases such as xenon which must be stored in high pressure canisters and is very expensive. These shortcomings have led to researching possible substitutes. Iodine was decided as a suitable candidate because it's cheaper, can be stored as a solid, and has similar mass properties as xenon. In this research, cathodes will be placed in a vacuum chamber and operated on both gases to observe their performance, allowing us to gain a better understanding of iodine's behavior. Several planned projects depend on the knowledge gained from this project, such as larger scaled tests and iodine fed hall thrusters. The tasks of this project included protecting the stainless-steel vacuum chamber by gold plating and Teflon® coating, building a stand to hold the cathode, creating an anode resistant to iodine, and testing the cathode once setup was complete. The successful operation of the cathode was demonstrated. However, the experimental setup proved ineffective at controlling the iodine flow. Current efforts are focused on this problem. REU Site: Fluid Mechanics with Analysis using Computations and Experiments NSF Grant EEC 1659710.

Study on the cathode of ion source for neutral beam injector

International Nuclear Information System (INIS)

Tanaka, Shigeru

1983-08-01

Durability of the cathode is an important problem in developing a high power long pulse ion source for neutral beam injector. The Purpose of this study is to develope a long life cathode and investigate the applicability of it to the source. Directly heated filaments which are commonly used as the cathode of injector source do not live very long in general. In the present work, an indirectly heated hollow cathode made of impregnated porous tungsten tube is proposed as the alternative of the directly heated cathode. At first, we fabricated a small hollow cathode to study the discharge characteristcs in a bell-jar configuration and to apply it to a duoPIGatron hydrogen ion source. The experiment showed that the gas flow rate for sustaining the stable arc discharge in the discharge chamber becomes higher than that when the filament cathode is used. To solve this problem, an experiment for gas reduction was made using a newly fabricated larger hollow cathode and a magnetic multi-pole ion source. The influence of the orifice diameter, the effect of a button and of magnetic field on the gas flow rate were experimentally studied and a method for gas reduction was found. In addition, effect of the magnetic field on the characteristics of the hollow cathode ion source was examined in detail and an optimum field configuration around the cathode was found. Finally, beam extraction from an intensively cooled hollow cathode ion source for up to 10 sec was successfully carried out. (author)

LOW TEMPERATURE CATHODE SUPPORTED ELECTROLYTES

Energy Technology Data Exchange (ETDEWEB)

Harlan U. Anderson; Fatih Dogan; Vladimir Petrovsky

2002-03-31

This project has three main goals: Thin Films Studies, Preparation of Graded Porous Substrates and Basic Electrical Characterization and testing of Planar Single Cells. This period has continued to address the problem of making dense 1/2 to 5 {micro}m thick dense layers on porous substrates (the cathode LSM). Our current status is that we are making structures of 2-5 cm{sup 2} in area, which consist of either dense YSZ or CGO infiltrated into a 2-5 {micro}m thick 50% porous layer made of either nanoncrystalline CGO or YSZ powder. This composite structure coats a macroporous cathode or anode; which serves as the structural element of the bi-layer structure. These structures are being tested as SOFC elements. A number of structures have been evaluated both as symmetrical and as button cell configuration. Results of this testing indicates that the cathodes contribute the most to cell losses for temperatures below 750 C. In this investigation different cathode materials were studied using impedance spectroscopy of symmetric cells and IV characteristics of anode supported fuel cells. Cathode materials studied included La{sub 0.8}Sr{sub 0.2}Co{sub 0.2}Fe{sub 0.8}O{sub 3} (LSCF), La{sub 0.7}Sr{sub 0.2}MnO{sub 3} (LSM), Pr{sub 0.8}Sr{sub 0.2}Fe{sub 0.8}O{sub 3} (PSCF), Sm{sub 0.8}Sr{sub 0.2}Co{sub 0.2}Fe{sub 0.8}O{sub 3} (SSCF), and Yb{sub .8}Sr{sub 0.2}Co{sub 0.2}Fe{sub 0.8}O{sub 3} (SSCF). A new technique for filtering the Fourier transform of impedance data was used to increase the sensitivity of impedance analysis. By creating a filter specifically for impedance spectroscopy the resolution was increased. The filter was tailored to look for specific circuit elements like R//C, Warburg, or constant phase elements. As many as four peaks can be resolved using the filtering technique on symmetric cells. It may be possible to relate the different peaks to material parameters, like the oxygen exchange coefficient. The cathode grouped in order from lowest to highest ASR is

PATRIMÔNIO CULTURAL ARQUEOLÓGICO: INSTRUMENTO DE DESENVOLVIMENTO TURÍSTICO

OpenAIRE

Rossano Bastos

2012-01-01

O presente trabalho trata das perspectivas de aproveitamento do Patrimônio Cultural Arqueológico como instrumento de desenvolvimento turístico.PALAVRAS-CHAVE: Arqueologia; Turismo;Desenvolvimento.ABSTRACT: This work considers some improvement perspectives ofthe archaeological cultural heritage as an instrument of tourism development.KEY-WORDS: Archaeology; Tourism; Development. 

Patrocínio esportivo nos jogos Rio 2016: estudo de caso de um fornecedor de materiais

OpenAIRE

Valle, Thalles Sanches

2016-01-01

Estudo de caráter qualitativo que teve como objetivo analisar o patrocínio de materiais da modalidade de Levantamento de Peso (LP), durante os Jogos Olímpicos do Rio 2016, buscando entender quais os benefícios esperados e os resultados atingidos por tal investimento. Para atingir este objetivo foi levantada literatura sobre: patrocínio esportivo que pode ser entendido quando uma empresa de qualquer setor aloca direta ou indiretamente recursos em eventos esportivos, atletas, equipes e organiza...

Mesoporous Nickel Oxide (NiO) Nanopetals for Ultrasensitive Glucose Sensing

Science.gov (United States)

Mishra, Suryakant; Yogi, Priyanka; Sagdeo, P. R.; Kumar, Rajesh

2018-01-01

Glucose sensing properties of mesoporous well-aligned, dense nickel oxide (NiO) nanostructures (NSs) in nanopetals (NPs) shape grown hydrothermally on the FTO-coated glass substrate has been demonstrated. The structural study based investigations of NiO-NPs has been carried out by X-ray diffraction (XRD), electron and atomic force microscopies, energy dispersive X-ray (EDX), and X-ray photospectroscopy (XPS). Brunauer-Emmett-Teller (BET) measurements, employed for surface analysis, suggest NiO's suitability for surface activity based glucose sensing applications. The glucose sensor, which immobilized glucose on NiO-NPs@FTO electrode, shows detection of wide range of glucose concentrations with good linearity and high sensitivity of 3.9 μA/μM/cm2 at 0.5 V operating potential. Detection limit of as low as 1 μΜ and a fast response time of less than 1 s was observed. The glucose sensor electrode possesses good anti-interference ability, stability, repeatability & reproducibility and shows inert behavior toward ascorbic acid (AA), uric acid (UA) and dopamine acid (DA) making it a perfect non-enzymatic glucose sensor.

Polymer coatings as separator layers for microbial fuel cell cathodes

KAUST Repository

Watson, Valerie J.; Saito, Tomonori; Hickner, Michael A.; Logan, Bruce E.

2011-01-01

and increased coulombic efficiency (CE = 56-64%) relative to an uncoated cathode (29 ± 8%), but decreased power production (255-574 mW m-2). Electrochemical characterization of the cathodes ex situ to the MFC showed that the cathodes with the lowest charge

Controlled synthesis of mesoporous β-Ni(OH){sub 2} and NiO nanospheres with enhanced electrochemical performance

Energy Technology Data Exchange (ETDEWEB)

Xing, Shengtao; Wang, Qian [College of Chemistry and Material Sciences, Hebei Normal University, Shijiazhuang 050016 (China); Ma, Zichuan, E-mail: mazc@vip.163.com [College of Chemistry and Material Sciences, Hebei Normal University, Shijiazhuang 050016 (China); Wu, Yinsu; Gao, Yuanzhe [College of Chemistry and Material Sciences, Hebei Normal University, Shijiazhuang 050016 (China)

2012-09-15

Highlights: ► Uniform mesoporous β-Ni(OH){sub 2} and NiO nanospheres with hierarchical structures were synthesized by a simple complexation–precipitation method. ► Both ammonia and citrate played an important role for the formation of mesoporous nanospheres. ► β-Ni(OH){sub 2} and NiO nanospheres showed excellent capacitive properties due to their mesoporous structures and larger surface areas. -- Abstract: Uniform mesoporous β-Ni(OH){sub 2} and NiO nanospheres with hierarchical structures were synthesized by a facile complexation–precipitation method. The effects of ammonia and citrate on the structure and morphology of the products were thoroughly investigated by X-ray powder diffraction, scanning electron microscopy, transmission electron microscopy and nitrogen adsorption–desorption measurements. The results indicated that ammonia played an important role for the formation of flowerlike spheres assembled from nanosheets. The addition of citrate could remarkably reduce the particle sizes and increase the specific surface areas of flowerlike spheres. A possible formation mechanism based on the experimental results was proposed to understand their growing procedures. β-Ni(OH){sub 2} and NiO nanospheres prepared with the addition of citrate showed excellent capacitive properties due to their mesoporous structures and large surface areas, suggesting the importance of controlled synthesis of hierarchical nanostructures for their applications.

Cathodic Protection Model Facility

Data.gov (United States)

Federal Laboratory Consortium — FUNCTION: Performs Navy design and engineering of ship and submarine impressed current cathodic protection (ICCP) systems for underwater hull corrosion control and...

Application of M-type cathodes to high-power cw klystrons

Science.gov (United States)

Isagawa, S.; Higuchi, T.; Kobayashi, K.; Miyake, S.; Ohya, K.; Yoshida, M.

1999-05-01

Two types of high-power cw klystrons have been widely used at KEK in both TRISTAN and KEKB e +e - collider projects: one is a 0.8 MW/1.0 MW tube, called YK1302/YK1303 (Philips); the other is a 1.2 MW tube, called E3786/E3732 (Toshiba). Normally, the dispenser cathodes of the `B-type' and the `S-type' have been used, respectively, but for improved versions they have been replaced by low-temperature cathodes, called the `M-type'. An Os/Ru coating was applied to the former, whereas an Ir one was applied to the latter. Until now, all upgraded tubes installing M-type cathodes, 9 and 8 in number, respectively, have worked successfully without any dropout. A positive experience concerning the lifetime under real operation conditions has been obtained. M-type cathodes are, however, more easily poisoned. One tube installing an Os/Ru-coated cathode showed a gradual, and then sudden decrease in emission during an underheating test, although the emission could fortunately be recovered by aging at the KEK test field. Once sufficiently aged, the emission of an Ir-coated cathode proved to be very high and stable, and its lifetime is expected to be very long. One disadvantage of this cathode is, however, susceptibility to gas poisoning and the necessity of long-term initial aging. New techniques, like ion milling and fine-grained tungsten top layers, were not as successful as expected from their smaller scale applications to shorten the initial aging period. A burn-in process at higher cathode loading was efficient to make the poisoned cathode active and to decrease unwanted Wehnelt emission. On top of that, the emission cooling, and thus thermal conductivity near the emitting layer could play an important role in such large-current cathodes as ours.

Cathodic behavior of zirconium in aqueous solutions

International Nuclear Information System (INIS)

Hine, F.; Yasuda, M.; Sato, H.

1977-01-01

The electrochemical behavior of Zr was studied by polarization measurements. The surface oxide and zirconium hydride formed by cathodic polarization of Zr have been examined by X-ray, SEM, and a hardness tester. Zirconium hydride would form on Zr cathode after the surface oxide is reduced at the potential, which is several hundred mV more noble than the predicted value shown by the Pourbaix diagram. The parameters for the hydrogen evolution reaction on the hydride formed Zr cathode differs from that on the oxide covered surface, which means that hydrogen evolution takes place on both surfaces under a different mechanism, while details are still veiled at present

MIGRAÇÃO DA ESPÉCIE INORGÂNICA – Alumínio – DOS UTENSÍLIOS CULINÁRIOS PARA O CEREAL ARROZ

Directory of Open Access Journals (Sweden)

Pedro Paulo Palomino Lúcio

2011-02-01

Full Text Available Os utensílios culinários sempre estiveram em constante “evolução”, buscando praticidade, e nunca importando com o nível de toxicologia. Objetivando-se avaliar a migração de alumínio durante o cozimento do arroz por titulação indireta e FAAS, com extrações em HCl 1,0 e 0,1 mol L-1, amostras de arroz foram cozidas em três diferentes utensílios culinários: panela/colher de alumínio, panela de alumínio/colher de polietileno e panela de vidro/colher de polietileno. Na titulação indireta, não foi detectada diferença estatística pelo uso das diferentes concentrações, embora ocorreu detecções na concentração 0,1 mol L-1, já pela técnica FAAS houve apenas detecção e diferença estatística para panela de alumínio/colher de alumínio.

Memória, patrimônio, bibliotecas nacionais e a construção da identidade coletiva

Directory of Open Access Journals (Sweden)

Marcia Rodrigues

2015-09-01

Full Text Available Este trabalho visa contribuir para o entendimento da relação entre as bibliotecas e a construção da memória coletiva e suas implicações na preservação do patrimônio cultural nacional. Para tanto, realiza uma revisão teórica sobre memória e patrimônio, fundamentada em importantes estudiosos da área. Igualmente, elabora uma revisão sobre o surgimento das bibliotecas nacionais, fundamentada em autores contemporâneos. Na sequência, tece considerações a respeito da missão institucional das bibliotecas nacionais, traçando um breve esboço da trajetória histórica da Biblioteca Nacional brasileira, demonstrando seu papel na salvaguarda do patrimônio bibliográfico do país.

Air cathode structure manufacture

Science.gov (United States)

Momyer, William R.; Littauer, Ernest L.

1985-01-01

An improved air cathode structure for use in primary batteries and the like. The cathode structure includes a matrix active layer, a current collector grid on one face of the matrix active layer, and a porous, nonelectrically conductive separator on the opposite face of the matrix active layer, the collector grid and separator being permanently bonded to the matrix active layer. The separator has a preselected porosity providing low IR losses and high resistance to air flow through the matrix active layer to maintain high bubble pressure during operation of the battery. In the illustrated embodiment, the separator was formed of porous polypropylene. A thin hydrophobic film is provided, in the preferred embodiment, on the current collecting metal grid.

The cathode material for a plasma-arc heater

Science.gov (United States)

Yelyutin, A. V.; Berlin, I. K.; Averyanov, V. V.; Kadyshevskii, V. S.; Savchenko, A. A.; Putintseva, R. G.

1983-11-01

The cathode of a plasma arc heater experiences a large thermal load. The temperature of its working surface, which is in contact with the plasma, reaches high values, as a result of which the electrode material is subject to erosion. Refractory metals are usually employed for the cathode material, but because of the severe erosion do not usually have a long working life. The most important electrophysical characteristic of the electrode is the electron work function. The use of materials with a low electron work function allows a decrease in the heat flow to the cathode, and this leads to an increase in its erosion resistance and working life. The electroerosion of certain materials employed for the cathode in an electric arc plasma generator in the process of reduction smelting of refractory metals was studied.

On the actual cathode mixed potential in direct methanol fuel cells

Science.gov (United States)

Zago, M.; Bisello, A.; Baricci, A.; Rabissi, C.; Brightman, E.; Hinds, G.; Casalegno, A.

2016-09-01

Methanol crossover is one of the most critical issues hindering commercialization of direct methanol fuel cells since it leads to waste of fuel and significantly affects cathode potential, forming a so-called mixed potential. Unfortunately, due to the sluggish anode kinetics, it is not possible to obtain a reliable estimation of cathode potential by simply measuring the cell voltage. In this work we address this limitation, quantifying the mixed potential by means of innovative open circuit voltage (OCV) tests with a methanol-hydrogen mixture fed to the anode. Over a wide range of operating conditions, the resulting cathode overpotential is between 250 and 430 mV and is strongly influenced by methanol crossover. We show using combined experimental and modelling analysis of cathode impedance that the methanol oxidation at the cathode mainly follows an electrochemical pathway. Finally, reference electrode measurements at both cathode inlet and outlet provide a local measurement of cathode potential, confirming the reliability of the innovative OCV tests and permitting the evaluation of cathode potential up to typical operating current. At 0.25 A cm-2 the operating cathode potential is around 0.85 V and the Ohmic drop through the catalyst layer is almost 50 mV, which is comparable to that in the membrane.

High-Performance Direct Methanol Fuel Cells with Precious-Metal-Free Cathode.

Science.gov (United States)

Li, Qing; Wang, Tanyuan; Havas, Dana; Zhang, Hanguang; Xu, Ping; Han, Jiantao; Cho, Jaephil; Wu, Gang

2016-11-01

Direct methanol fuel cells (DMFCs) hold great promise for applications ranging from portable power for electronics to transportation. However, apart from the high costs, current Pt-based cathodes in DMFCs suffer significantly from performance loss due to severe methanol crossover from anode to cathode. The migrated methanol in cathodes tends to contaminate Pt active sites through yielding a mixed potential region resulting from oxygen reduction reaction and methanol oxidation reaction. Therefore, highly methanol-tolerant cathodes must be developed before DMFC technologies become viable. The newly developed reduced graphene oxide (rGO)-based Fe-N-C cathode exhibits high methanol tolerance and exceeds the performance of current Pt cathodes, as evidenced by both rotating disk electrode and DMFC tests. While the morphology of 2D rGO is largely preserved, the resulting Fe-N-rGO catalyst provides a more unique porous structure. DMFC tests with various methanol concentrations are systematically studied using the best performing Fe-N-rGO catalyst. At feed concentrations greater than 2.0 m, the obtained DMFC performance from the Fe-N-rGO cathode is found to start exceeding that of a Pt/C cathode. This work will open a new avenue to use nonprecious metal cathode for advanced DMFC technologies with increased performance and at significantly reduced cost.

Preparation of mesoporous NiO with a bimodal pore size distribution and application in electrochemical capacitors

Energy Technology Data Exchange (ETDEWEB)

Wang Dengchao; Ni Wenbin; Pang Huan; Lu Qingyi; Huang Zhongjie [Key Laboratory of Analytical Chemistry for Life Science (MOE), School of Chemistry and Chemical Engineering, Nanjing University, Nanjing 210008 (China); Zhao Jianwei, E-mail: zhaojw@nju.edu.c [Key Laboratory of Analytical Chemistry for Life Science (MOE), School of Chemistry and Chemical Engineering, Nanjing University, Nanjing 210008 (China)

2010-09-01

Mesoporous nickel oxide with a porous structure exhibiting a bimodal pore size distribution (2.6 and 30.3 nm diameter pores) has been synthesized in this paper. Firstly, a mesoporous precursor of coordination complex Ni{sub 3}(btc){sub 2}.12H{sub 2}O (btc = 1,3,5-benzenrtricarboxylic acid) is synthesized based on the metal-organic coordination mechanism by a hydrothermal method. Then mesoporous NiO with a bimodal size distribution is obtained by calcining the precursor in the air, and characterized by transmission electron microscopy and N{sub 2} adsorption measurements. Such unique multiple porous structure indicates a promising application of the obtained NiO as electrode materials for supercapacitors. The electrochemical behavior has been investigated by cyclic voltammogram, electrochemical impedance spectra and chronopotentiometry in 3 wt.% KOH aqueous electrolyte. The results reveal that the prepared NiO has high-capacitance retention at high scan rate and exhibits excellent cycle-life stability due to its special mesoporous character with bimodal size distribution.

Facile synthesis of Co3O4 nanowires grown on hollow NiO microspheres with superior electrochemical performance

International Nuclear Information System (INIS)

Fan, Meiqing; Ren, Bo; Yu, Lei; Song, Dalei; Liu, Qi; Liu, Jingyuan; Wang, Jun; Jing, Xiaoyan; Liu, Lianhe

2015-01-01

Graphical abstract: Display Omitted - Highlights: • The NiO hollow spheres were decorated by Co 3 O 4 nanowires. • The NiO hollow spheres were comprised of many NiO particles. • The Co 3 O 4 nanowires were composed of nanoparticles. • The NiO/Co 3 O 4 core/shell nanocomposites have good electrochemical properties. - Abstract: The NiO/Co 3 O 4 core/shell composites as a promising supercapacitor material have been fabricated by facile hydrothermal process. The structure and morphology of the NiO/Co 3 O 4 core/shell composites were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results indicated that the NiO hollow spheres were decorated by Co 3 O 4 nanowires, and the nanowires were composed of nanoparticles. Electrochemical properties were characterized by cyclic voltammetry, galvanostatic charge/discharge measurements, and electrochemical impedance spectroscopy. The results suggested that the NiO/Co 3 O 4 core/shell composites had good electrochemical reversibility and displayed superior capacitive performance with large capacitance (510 F g −1 ). Moreover, NiO/Co 3 O 4 core/shell composites showed excellent cyclic performanceafter 1000 cycles

Effects of cathodic protection on cracking of high-strength pipeline steels

Energy Technology Data Exchange (ETDEWEB)

Elboujdaini, M.; Revie, R. W.; Attard, M. [CANMET Materials Technology Laboratory, Ottawa, ON(Canada)], email: melboujd@nrcan.gc.ca

2010-07-01

Four strength levels of pipeline steels, ranging from X-70 to X-120, were compared to determine whether higher strength materials are more susceptible to hydrogen embrittlement under cathodic protection. Ductility was measured in a solution at four protection levels, going from no cathodic protection to 500 mV of overprotection. All four steels showed loss of ductility under cathodic protection. Under cathodic polarization, the loss of ductility increased with the strength of the steel and the activity of the potential. After slow-strain-rate experiments conducted in air and examination of fracture surfaces, it is concluded that application of cathodic potentials, cathodic overprotection, higher strength of steel, and exposure to aqueous solution are factors that decrease the ductility of steel. Hydrogen reduction seems to be an important factor in ductility reduction and fractures. Observations suggest that high-strength pipelines need better control of cathodic protection than lower-strength pipelines.

Plasma-induced field emission and plasma expansion of carbon nanotube cathodes

International Nuclear Information System (INIS)

Liao Qingliang; Zhang Yue; Qi Junjie; Huang Yunhua; Xia Liansheng; Gao Zhanjun; Gu Yousong

2007-01-01

High intensity electron emission cathodes based on carbon nanotube films have been successfully fabricated. An investigation of the explosive field emission properties of the carbon nanotube cathode in a double-pulse mode was presented and a high emission current density of 245 A cm -2 was obtained. The formation of the cathode plasma layer was proved and the production process of the electron beams from the cathode was explained. The time and space resolution of the electron beams flow from the cathode was investigated. The plasma expanded at a velocity of ∼8.17 cm μs -1 towards the anode and influenced on the intensity and distribution of electron beams obviously. The formation of cathode plasma had no preferential position and the local enhancement of electron beams was random. This carbon nanotube cathode appears to be suitable for high-power microwave device applications

High-Current Cold Cathode Employing Diamond and Related Materials

Energy Technology Data Exchange (ETDEWEB)

Hirshfield, Jay L. [Omega-P, Inc., New Haven, CT (United States)

2014-10-22

The essence of this project was for diamond films to be deposited on cold cathodes to improve their emission properties. Films with varying morphology, composition, and size of the crystals were deposited and the emission properties of the cathodes that utilize such films were studied. The prototype cathodes fabricated by the methods developed during Phase I were tested and evaluated in an actual high-power RF device during Phase II. These high-power tests used the novel active RF pulse compression system and the X-band magnicon test facility at US Naval Research Laboratory. In earlier tests, plasma switches were employed, while tests under this project utilized electron-beam switching. The intense electron beams required in the switches were supplied from cold cathodes embodying diamond films with varying morphology, including uncoated molybdenum cathodes in the preliminary tests. Tests with uncoated molybdenum cathodes produced compressed X-band RF pulses with a peak power of 91 MW, and a maximum power gain of 16.5:1. Tests were also carried out with switches employing diamond coated cathodes. The pulse compressor was based on use of switches employing electron beam triggering to effect mode conversion. In experimental tests, the compressor produced 165 MW in a ~ 20 ns pulse at ~18× power gain and ~ 140 MW at ~ 16× power gain in a 16 ns pulse with a ~ 7 ns flat-top. In these tests, molybdenum blade cathodes with thin diamond coatings demonstrated good reproducible emission uniformity with a 100 kV, 100 ns high voltage pulse. The new compressor does not have the limitations of earlier types of active pulse compressors and can operate at significantly higher electric fields without breakdown.

Fundamental Investigations and Rational Design of Durable High-Performance SOFC Cathodes

Energy Technology Data Exchange (ETDEWEB)

Chen, Yu [Georgia Inst. of Technology, Atlanta, GA (United States); Ding, Dong [Georgia Inst. of Technology, Atlanta, GA (United States); Wei, Tao [Georgia Inst. of Technology, Atlanta, GA (United States); Liu, Meilin [Georgia Inst. of Technology, Atlanta, GA (United States)

2016-03-31

The main objective of this project is to unravel the degradation mechanism of LSCF cathodes under realistic operating conditions with different types of contaminants, aiming towards the rational design of cathodes with high-performance and enhanced durability by combining a porous backbone (such as LSCF) with a thin catalyst coating. The mechanistic understanding will help us to optimize the composition and morphology of the catalyst layer and microstructure of the LSCF backbone for better performance and durability. More specifically, the technical objectives include: (1) to unravel the degradation mechanism of LSCF cathodes under realistic operating conditions with different types of contaminants using in situ and ex situ measurements performed on specially-designed cathodes; (2) to examine the microstructural and compositional evolution of LSCF cathodes as well as the cathode/electrolyte interfaces under realistic operating conditions; (3) to correlate the fuel cell performance instability and degradation with the microstructural and morphological evolution and surface chemistry change of the cathode under realistic operating conditions; (4) to explore new catalyst materials and electrode structures to enhance the stability of the LSCF cathode under realistic operating conditions; and (5) to validate the long term stability of the modified LSCF cathode in commercially available cells under realistic operating conditions. We have systematically evaluated LSCF cathodes in symmetrical cells and anode supported cells under realistic conditions with different types of contaminants such as humidity, CO₂, and Cr. Electrochemical models for the design of test cells and understanding of mechanisms have been developed for the exploration of fundamental properties of electrode materials. It is demonstrated that the activity and stability of LSCF cathodes can be degraded by the introduction of contaminants. The microstructural and compositional evolution of LSCF

SOFC LSM:YSZ cathode degradation induced by moisture: An impedance spectroscopy study

DEFF Research Database (Denmark)

Nielsen, Jimmi; Mogensen, Mogens Bjerg

2011-01-01

The cause of the degradation effect of moisture during operation of LSM cathode based SOFCs has been investigated by means of a detailed impedance characterization on LSM:YSZ composite cathode based SOFCs. Further the role of YSZ as cathode composite material was studied by measurements on SOFCs...... with a LSM:CGO composite cathode on a CGO interdiffusion barrier layer. It was found that both types of cathodes showed similar electrochemical characteristics towards the presence of moisture during operation. Upon addition and removal of moisture in the fed air the impedance study showed a change...... in the high frequency cathode arc, which is associated with the charge transport/transfer at the LSM/YSZ interface. On prolonged operation with the presence of moisture an ongoing increase in the high frequency cathode arc resulted in a permanent loss of cathode/electrolyte contact and thus increase...

BIODIGESTÃO ANAERÓBICA: UMA ALTERNATIVA PARA USINAS DE LATICÍNIOS

Directory of Open Access Journals (Sweden)

Melânia Palermo Manfron

1991-04-01

Full Text Available RESUMO O objetivo deste trabalho foi mostrar a viabilidade da utilização de biodigestores anaeróbicos na redução do DQO e DBO nos resíduos de laticínios e como fonte de energia, através da produção de metano (CH4. O processo apresenta basicamente três estágios importantes na compreensão das fermentações anaeróbicas, devido aparecer inúmeros microrganismos interatuantes na degradação do substrato. A biodigestão anaeróbica é bastante sensível à variações ambientais, o que ocasiona um desequilíbrio nas populações bacterianas afetando o rendimento e a velocidade do processo. Entretanto, hoje é uma alternativa nobre para o tratamento de efluentes líquidos industriais e, principalmente, os de usinas de laticínios que geram efluentes com elevada carga orgânica.

INVENTORS AND MASTERS: JOÃO VÁRIO AND ARMÉNIO VIEIRA

Directory of Open Access Journals (Sweden)

Rui Guilherme Silva

2015-11-01

Full Text Available João Vário and Arménio Vieira are today´s most influential Cape Verde­an poets. During the first years after Independency Vário publishes in the weekly Voz di Povo some excerpts of the “Epistles to my brother António”, in which he demands the creation of a more complex, knowledgeable and universal poetry than the one the new generations had inherited from Cla­ridade. Concomitantly, he requests the appearance of “lucid, wise, profes­sional” literary critics in Cape Verde. Arménio Vieira, who coordinated the cultural pages of Voz di Povo at the time, comments Vário´s most con­troversial theses, and analyses an excerpt of the later Exemplo Próprio. The invention of Silvenius, the libertarian alter-ego of Vieira, endorses the final overcoming of Claridade’s aesthetic and the establishment of a new poetic paradigm of cosmopolitan nature.

D. Antônio de Macedo Costa: uma teologia do poder

Directory of Open Access Journals (Sweden)

Milton Carlos Costa

2016-05-01

Full Text Available A personalidade de D. Antônio de Macedo Costa configura-se como uma das mais conhecidas da história do catolicismo brasileiro, principalmente devido à sua atuação durante a Questão Religiosa (1872-1875, que opôs a Igreja brasileira ao Estado. Nosso trabalho visa fazer uma exploração inicial de sua teologia do poder, expressa nos documentos elaborados por este batalhador incansável da igreja ultramontana, que procurou impulsionar com grande energia o processo que a historiografia chama de romanização da Igreja brasileira. Podemos dizer que todas as formulações de D. Antônio estão atravessadas pela concepção de uma teologia do poder: é pelo prisma do poder que ele vê a Igreja e é de maneira consciente e explícita que privilegia o Estado como interlocutor da Igreja.

Large area dispenser cathode applied to high current linac

International Nuclear Information System (INIS)

Yang Anmin; China Academy of Engineering Physics, Mianyang; Wu Dengxue; Liu Chenjun; Xia Liansheng; Wang Wendou; Zhang Kaizhi

2005-01-01

The paper introduced a dispenser cathode (411 M) which was 55 mm in diameter. A 200 kV long pulsed power generator with 2 μs flattop based on Marx-PEN and system with heat and voltage insulation were built. A 52 A space charge limited current was gained, when the temperature was 1165 degree C and the filament current was 18 A on the cathode and the voltage of the pulse was 75 kV at the cathode test stand. Experimental results show that the current values are consistent with the numerical simulation. The experiment reveals that the deflated gas will influence the cathode emission ability. (authors)

Installation and operation manual on sea level gauge (Model: NIO_Ghana_2004)

Digital Repository Service at National Institute of Oceanography (India)

Joseph, A; Pereira, A; VijayKumar, K.; Prabhudesai, S.; Methar, A; Dias, M.

NIO sea level gauge is a pressure-based gauge that operates on 12 volts battery. The pressure-sensing element used in this gauge is a piezo-resistive programmable semiconductor transducer that provides pressure samples in RS-485 format...

Influence of discharge voltage on the sensitivity of the resultant sputtered NiO thin films toward hydrogen gas

Energy Technology Data Exchange (ETDEWEB)

Khalaf, Mohammed K. [Center of Applied Physics, Directorate of Materials Research, Ministry of Science and Technology, Baghdad (Iraq); Mutlak, Rajaa H. [Dept. of Physics, College of Science, University of Baghdad, Ministry of Higher Education and Scientific Research, Baghdad (Iraq); Khudiar, Ausama I., E-mail: ausamaikhudiar@yahoo.com [Center of Applied Physics, Directorate of Materials Research, Ministry of Science and Technology, Baghdad (Iraq); Hial, Qahtan G. [Dept. of Physics, College of Science, University of Baghdad, Ministry of Higher Education and Scientific Research, Baghdad (Iraq)

2017-06-01

Nickel oxide thin films were deposited on glass substrates as the main gas sensor for H{sub 2} by the DC sputtering technique at various discharge voltages within the range of 1.8–2.5 kV. Their structural, optical and gas sensing properties were investigated by XRD, AFM, SEM, ultraviolet visible spectroscopy and home-made gas sensing measurement units. A diffraction peak in the direction of NiO (200) was observed for the sputtered films, thereby indicating that these films were polycrystalline in nature. The optical band gap of the films decreased from 3.8 to 3.5 eV when the thickness of the films was increased from 83.5 to 164.4 nm in relation to an increase in the sputtering discharge voltage from 1.8 to 2.5 kV, respectively. The gas sensitivity performance of the NiO films that were formed was studied and the electrical responses of the NiO-based sensors toward different H{sub 2} concentrations were also considered. The sensitivity of the gas sensor increased with the working temperature and H{sub 2} gas concentration. The thickness of the NiO thin films was also an important parameter in determining the properties of the NiO films as H{sub 2} sensors. It was shown in this study that NiO films have the capability to detect H{sub 2} concentrations below 3% in wet air, a feature that allows this material to be used directly for the monitoring of the environment.

Chromium poisoning of LSM/YSZ and LSCF/CGO composite cathodes

DEFF Research Database (Denmark)

Bentzen, Janet Jonna; Høgh, Jens Valdemar Thorvald; Barfod, Rasmus

2009-01-01

from 300 to 2,970 h. Both LSM/YSZ and LSCF/CGO cathodes were sensitive to chromium poisoning; LSCF/CGO cathodes to a lesser extent than LSM/YSZ. Humid air aggravated the degradation of the cathode performance. Post-mortem electron microscopic investigations revealed several Cr-containing compounds...

Surface Modification Technique of Cathode Materials for LI-ION Battery

Science.gov (United States)

Jia, Yongzhong; Han, Jinduo; Jing, Yan; Jin, Shan; Qi, Taiyuan

Cathode materials for Li-ion battery LiMn2O4 and LiCo0.1Mn1.9O4 were prepared by soft chemical method. Carbon, which was made by decomposing organic compounds, was used as modifying agent. Cathode material matrix was mixed with water solution that had contained organic compound such as cane sugar, soluble amylum, levulose et al. These mixture were reacted at 150 200 °C for 0.5 4 h in a Teflon-lined autoclave to get a series of homogeneously C-coated cathode materials. The new products were analyzed by X-ray diffraction (XRD) and infrared (IR). Morphology of cathode materials was characterized by scanning electron microscope (SEM) and transition electron microscope (TEM). The new homogeneously C-coated products that were used as cathode materials of lithium-ion battery had good electrochemical stability and cycle performance. This technique has free-pollution, low cost, simpleness and easiness to realize the industrialization of the cathode materials for Li-ion battery.

Releasing metal catalysts via phase transition: (NiO)0.05-(SrTi0.8Nb0.2O3)0.95 as a redox stable anode material for solid oxide fuel cells.

Science.gov (United States)

Xiao, Guoliang; Wang, Siwei; Lin, Ye; Zhang, Yanxiang; An, Ke; Chen, Fanglin

2014-11-26

Donor-doped perovskite-type SrTiO3 experiences stoichiometric changes at high temperatures in different Po2 involving the formation of Sr or Ti-rich impurities. NiO is incorporated into the stoichiometric strontium titanate, SrTi0.8Nb0.2O3-δ (STN), to form an A-site deficient perovskite material, (NiO)0.05-(SrTi0.8Nb0.2O3)0.95 (Ni-STN), for balancing the phase transition. Metallic Ni nanoparticles can be released upon reduction instead of forming undesired secondary phases. This material design introduces a simple catalytic modification method with good compositional control of the ceramic backbones, by which transport property and durability of solid oxide fuel cell anodes are largely determined. Using Ni-STN as anodes for solid oxide fuel cells, enhanced catalytic activity and remarkable stability in redox cycling have been achieved. Electrolyte-supported cells with the cell configuration of Ni-STN-SDC anode, La0.8Sr0.2Ga0.87Mg0.13O3 (LSGM) electrolyte, and La0.6Sr0.4Co0.2Fe0.8O3 (LSCF) cathode produce peak power densities of 612, 794, and 922 mW cm(-2) at 800, 850, and 900 °C, respectively, using H2 as the fuel and air as the oxidant. Minor degradation in fuel cell performance resulted from redox cycling can be recovered upon operating the fuel cells in H2. Such property makes Ni-STN a promising regenerative anode candidate for solid oxide fuel cells.

Reciclagem de Cavacos de Titânio para a Deposição de Revestimentos Duros por Soldagem

Directory of Open Access Journals (Sweden)

José Gedael Fagundes Júnior

2015-03-01

Full Text Available O titânio é um metal nobre e possui excelentes propriedades biomecânicas, podendo assim ser plenamente aceito pelo organismo humano. A grande demanda na utilização de implantes dentários, fabricados a partir de ligas de titânio traz consigo um aumento significativo na geração de resíduos (cavacos, resultantes dos processos de usinagem empregados. Com o objetivo de reduzir os impactos ambientais, soluções alternativas para a reutilização de tais resíduos têm sido estudadas. O carboneto de titânio (TiC possui elevada dureza, o que potencialmente permitiria a sua utilização como reforço em revestimentos antidesgaste aplicados em equipamentos das indústrias sucroalcooleira e mineradoras. Neste trabalho cavacos de ligas a base de titânio foram processados e utilizados como matéria prima para a fabricação de consumíveis experimentais de soldagem. Cordões de solda foram produzidos sobre amostras de aço-carbono por soldagem a arco elétrico com proteção gasosa e eletrodo de tungstênio (tradução do termo inglês GTAW. A caracterização microestrutural do metal de solda foi realizada por MEV e difração de raios-X. O comportamento mecânico dos revestimentos foi analisado por meio de um ultramicrodurômetro digital. Verificou-se que a microestrutura do metal de solda era composta por partículas não prismáticas de alta dureza distribuídas em uma matriz ferrítica. Medidas feitas por microanálise EDS mostraram diferenças na concentração de titânio entre a matriz e as partículas duras, onde maiores teores deste elemento foram identificados. A análise cristalográfica confirmou que houve a formação de carbonetos de titânio envoltos por uma matriz de ferrita.

Oxide cathodes produced by plasma deposition

International Nuclear Information System (INIS)

Scheitrum, G.; Caryotakis, G.; Pi, T.; Umstattd, R.; Brown, I.; Montiero, O.

1997-01-01

These are two distinct applications for high-current-density, long-life thermionic cathodes. The first application is as a substitute for explosive emission cathodes used in high-power microwave (HPM) devices being developed for Air Force programs. The second application is in SLAC's X-band klystrons for the Next Linear Collider (NLC). SLAC, UCD, and LBL are developing a plasma deposition process that eliminates the problems with binders, carbonate reduction, peeling, and porosity. The emission layer is deposited using plasma deposition of metallic barium in vacuum with an oxygen background gas. An applied bias voltage drives the oxide plasma into the nickel surface. Since the oxide is deposited directly, it does not have problems with poisoning from a hydrocarbon binder. The density of the oxide layer is increased from the 40--50% for standard oxide cathodes to nearly 100% for plasma deposition

Candida glabrata um patogénio emergente?

OpenAIRE

Matilde, Filipa Alexandra Veiga

2014-01-01

Dissertação para obtenção do grau de Mestre no Instituto Superior de Ciências da Saúde Egas Moniz Nas últimas décadas as infecções fúngicas têm aumentado exponencialmente. Apesar de Candida albicans (C. albicans) continuar a ser a espécie isolada com maior frequência, as espécies não albicans tem vindo a proliferar rapidamente. Candida glabrata (C. glabrata) é uma das espécies emergentes como patogénio oportunista humano, sendo responsável maioritariamente por candidoses invasivas em pacie...

Self-organization in cathode boundary layer discharges in xenon

International Nuclear Information System (INIS)

Takano, Nobuhiko; Schoenbach, Karl H

2006-01-01

Self-organization of direct current xenon microdischarges in cathode boundary layer configuration has been studied for pressures in the range 30-140 Torr and for currents in the range 50 μA-1 mA. Side-on and end-on observations of the discharge have provided information on the structure and spatial arrangement of the plasma filaments. The regularly spaced filaments, which appear in the normal glow mode when the current is lowered, have a length which is determined by the cathode fall. It varies, dependent on pressure and current, between 50 and 70 μm. The minimum diameter is approximately 80 μm, as determined from the radiative emission in the visible. The filaments are sources of extensive excimer emission. Measurements of the cathode fall length have allowed us to determine the secondary emission coefficient for the discharge in the normal glow mode and to estimate the cathode fall voltage at the transition from normal glow mode to filamentary mode. It was found that the cathode fall voltage at this transition decreases, indicating the onset of additional electron gain processes at the cathode. The regular arrangement of the filaments, self-organization, is assumed to be due to Coulomb interactions between the positively charged cathode fall channels and positive space charges on the surface of the surrounding dielectric spacer. Calculations based on these assumptions showed good agreement with experimentally observed filament patterns

An adjustable electron achromat for cathode lens microscopy

Energy Technology Data Exchange (ETDEWEB)

Tromp, R.M., E-mail: rtromp@us.ibm.com [IBM T.J. Watson Research Center, 1101 Kitchawan Road, Yorktown Heights, NY 10598 (United States); Leiden Institute of Physics, Kamerlingh Onnes Laboratory, Niels Bohrweg 2, 2333 CA Leiden (Netherlands)

2015-12-15

Chromatic aberration correction in light optics began with the invention of a two-color-corrected achromatic crown/flint lens doublet by Chester Moore Hall in 1730. Such color correction is necessary because any single glass shows dispersion (i.e. its index of refraction changes with wavelength), which can be counteracted by combining different glasses with different dispersions. In cathode lens microscopes (such as Photo Electron Emission Microscopy – PEEM) we encounter a similar situation, where the chromatic aberration coefficient of the cathode lens shows strong dispersion, i.e. depends (non-linearly) on the energy with which the electrons leave the sample. Here I show how a cathode lens in combination with an electron mirror can be configured as an adjustable electron achromat. The lens/mirror combination can be corrected at two electron energies by balancing the settings of the electron mirror against the settings of the cathode lens. The achromat can be adjusted to deliver optimum performance, depending on the requirements of a specific experiment. Going beyond the achromat, an apochromat would improve resolution and transmission by a very significant margin. I discuss the requirements and outlook for such a system, which for now remains a wish waiting for fulfilment. - Highlights: • The properties of cathode objective lens plus electron mirror are discussed. • In analogy with light-optical achromats, cathode lens plus mirror can be configured as an electron achromat. • Unlike light optics, the electron achromat can be adjusted to best fulfill experimental requirements.

A complexidade do raciocínio clínico no processo de decisão

OpenAIRE

Magalhães, Dulce

2011-01-01

Importa compreender como se desenvolve a tomada de decisão no campo da área clínica de enfermagem porque nos elucida sobre a especificidade do raciocínio clínico enquanto instrumento básico de competência clínica.A análise de um conjunto de documentos científicos reunidos a partir de uma base de dados no período de 2002 a 2007 e sob os termos-chave clinical reasoning, clinical judgment, diagnostic reasoning e decision making permitiu-nos compreender que o raciocínio clínico para a tomada de ...

Determination of electric field strength and kinetic temperature in the cathode fall region of a hollow cathode discharge

Energy Technology Data Exchange (ETDEWEB)

De la Rosa, M I; Perez, C; Gruetzmacher, K [Universidad de Valladolid, Facultad de Ciencias, 47071 Valladolid (Spain); Gonzalo, A B; Del Val, J A, E-mail: delarosa@opt.uva.e [Universidad de Salamanca, Escuela Politecnica Superior, 05003 Avila (Spain)

2010-05-01

In this work, we demonstrate the high potential of two-photon excitation of the 1S -2S transition of atomic hydrogen followed by optogalvanic detection, for measuring under identical experimental conditions, the kinetic temperature and the electric field strength in the cathode sheath region of a hollow cathode discharge. The first obtained results for both parameters are discussed in this paper.

The design of cathode for organic photovoltaic devices

Science.gov (United States)

Song, De; Shi, Feng; Xia, Xuan; Li, Ye; Duanmu, Qingduo

2016-11-01

We have discussed the effect of the residual gas in the Al metal cathode deposition process and consequently influence the performance of organic photovoltaic devices (such as organic photoelectron detector or solar cell). We believe that the origin of degradation in Jsc and FF from the Al cathode device should be the formation of AlOx in the C60-Al interface, which contaminate the interface and plays a role like an energy barrier that block the charge collect process. To solve this problem the Ag and Alq3 layer had been inserted before the Al. Owing to the advantageous of Alq3 and Ag layer, the device which Al cathode prepared at a lower vacuum condition exhibits a comparable performance to that device which Al cathode deposited in regular situation. As an additional benefit, since the introducing of Alq3/Ag layer in the VOPc/C60 organic photovoltaic device performs a better near-infrared response, this phenomenon has been confirmed by means of both simulation and experimental data. So the design of our new cathode structure provides a degree of freedom to modulate the light absorption for organic photovoltaic devices in short-wave and long-wave.

Preservação do Patrimônio Arquitetônico e Urbano em São João Del Rei, Brasil: apontamentos sobre a atuação do Conselho Municipal de Preservação do Patrimônio Cultural .

Directory of Open Access Journals (Sweden)

Daniela Abritta Cota

2012-11-01

Full Text Available Este artigo busca refletir sobre a gestão do patrimônio arquitetônico e urbano em São João Del Rei, MG – Brasil, a partir das práticas empreendidas pelo Conselho Municipal de Preservação do Patrimônio Cultural (CMPPC, considerando a sua efetiva atuação no âmbito municipal. Inicialmente será apresentada uma reflexão teórico-conceitual sobre os condicionantes para intervenções urbanas em contextos com significativo patrimônio cultural, seguida da evolução da política patrimonial no Brasil. Posteriormente será dada ênfase ao estudo de caso de São João Del Rei.

Space and time dependent properties of the virtual cathode in a reflex-type pulsed ion diode (virtual cathode in a reflex-type pulsed ion diode)

International Nuclear Information System (INIS)

Matsumoto, Yoshio; Yano, Syukuro

1982-01-01

Properties of a virtual cathode in a pulsed ion diode composed of an insulator-mesh anode and a metal-mesh cathode were studied experimentally at anode voltages below 360kV. Potential distribution in the virtual cathode side was measured with an insulated electrostatic potential probe, and ion beam currents in virtual and real cathode sides were measured with biased ion collectors. A loss parameter for the electron current at the virtual cathode was evaluated from the measured electron current values by using relations derived from the one-dimensional Child-Langmuir theory applied to the reflex triode. The ion beam accompanies a considerable amount of electron current, and this influences the stability of the virtual cathode; this perturbation results in variations of ion current with time. Space potentials in the emitted ion beam are given, suggesting an existence of high energy electrons of several keV accelerated by positive space potential of the ion beam. (author)

Iron phosphate materials as cathodes for lithium batteries

CERN Document Server

Prosini, Pier Paolo

2011-01-01

""Iron Phosphate Materials as Cathodes for Lithium Batteries"" describes the synthesis and the chemical-physical characteristics of iron phosphates, and presents methods of making LiFePO4 a suitable cathode material for lithium-ion batteries. The author studies carbon's ability to increase conductivity and to decrease material grain size, as well as investigating the electrochemical behaviour of the materials obtained. ""Iron Phosphate Materials as Cathodes for Lithium Batteries"" also proposes a model to explain lithium insertion/extraction in LiFePO4 and to predict voltage profiles at variou

Impressed current cathodic protection of deep water structures

Digital Repository Service at National Institute of Oceanography (India)

Venkatesan, R.

that the cathodic protection design approaches for shallow water may not be adequate for deeper water. This paper discusses on environmental factors encountered in deep water and their effect on cathodic protection behaviour of steel. Further, current CP design...

Analytical study of electron flows with a virtual cathode

International Nuclear Information System (INIS)

Dubinov, A.E.

2000-01-01

The dynamics of the electron flow behavior by its injection into a half-space is considered. Two problems are considered, namely the long-term injection of a monoenergetic electron flow and instantaneous flow injection with an assigned electron energy spectrum. The all flow electrons in both cases return to the injection plane. The simple analytical self-consistent model of the initial stage of the virtual cathode formation in a plane-parallel equipotential gap is plotted in the course of analysis whereof the duration of the virtual cathode formation process is determined. The performance of this model is not limited by the multivalence of the electron velocity in the flow. This makes it possible to extend the frames of the model performance relative to the moment of the virtual cathode formation and to consider its dynamics. The frequency of electron oscillations in the potential cathode-virtual cathode well is determined on the basis of the above model [ru

The magnetic moment of NiO nanoparticles determined by Mössbauer spectroscopy

DEFF Research Database (Denmark)

Bahl, Christian Robert Haffenden; Hansen, Mikkel Fougt; Pedersen, Thomas

2006-01-01

We have studied the magnetic properties of 57Fe-doped NiO nanoparticles using Mössbauer spectroscopy and magnetization measurements. Two samples with different degrees of interparticle interaction were studied. In both samples the particles were characterized by high-resolution transmission...

A insustentável leveza do alumínio: impactos socioambientais da inserção do Brasil no mercado mundial de alumínio primário

Directory of Open Access Journals (Sweden)

Alen Batista Henriques

2013-11-01

Full Text Available O presente artigo procura discutir a produção de alumínio no Brasil e seus impactos socioambientais e à saúde pública. Os impactos da cadeia produtiva do alumínio colocam em xeque a ideia de crescimento sustentável difundido pelos grupos empresariais que atuam no setor. O artigo defende a tese de que a inserção do Brasil no mercado global do alumínio faz parte de uma nova configuração da Divisão Internacional do Trabalho (DIT, cujas atividades econômicas poluentes e altamente dependentes de energia, como o caso deste metal vêm se deslocando para nações periféricas ou emergentes, onde muitas vezes as legislações são menos austeras, do mesmo modo como são menos influentes os movimentos ambientalistas e as reivindicações das populações atingidas nos territórios afetados em seus direitos à saúde, ao ambiente saudável e à cultura. A competitividade desta commodity é garantida no mercado internacional, a partir da produção de externalidades como os danos ao ambiente, desmatamentos, emissões de gases do efeito estufa e de cenários de injustiça ambiental, como também nos empreendimentos de construção de barragens hidrelétricas que expõem comunidades tradicionais a situações que envolvem a perca de seus territórios.

DE PASSADOS POSSÍVEIS: REFLEXÕES SOBRE DISCURSO(S E PATRIMÔNIO(S

Directory of Open Access Journals (Sweden)

Martha Helena Loeblein Becker Morales

2013-02-01

Full Text Available Este artigo procura refletir acerca do passado como categoria discursiva, ancorado na contribuição teórica de Michel Foucault. Por meio de levantamento e discussão bibliográfica que contempla, em especial, os campos da História, da Arqueologia e do Patrimônio, objetiva-se ponderar sobre a construção conceitual em torno do estudo do passado, conforme desenvolvimentos teóricos recentes. Parte inicial de um trabalho mais amplo, este é um texto que convida o leitor a conhecer e situar alguns debates centrais para questões tão atuais quanto problemáticas como a gestão pública do patrimônio cultural. Palavras-chave: passado, discurso, patrimônio   ABSTRACT This article reflects upon the past as a discursive analytical category, based on Michel Foucault’s theoretical contributions. Through a bibliographical survey and analysis regarding especially the fields of History, Archaeology and Heritage, the purpose is to shed light on the conceptual framework construction of the study of the past, considering recent theoretical developments. As part of a bigger project, this is a text that invites its reader to know and to place some of the key debates surrounding issues as current and problematic as the public management of cultural heritage. Key-words: past, discourse, heritage

The explosive cathode on the base of carbon-fibrous plastic material

International Nuclear Information System (INIS)

Korenev, S.A.; Baranov, A.M.; Kostyuchenko, S.V.; Chernenko, N.M.

1988-01-01

Production process of exploseve cathodes on the base of carbon-fibrous plastic material of any geometric form and size is discussed. Experimental study of current take-off from cathodes with diameter 2 cm of 10 kV and 150-250 kV voltage are given. It is shown that ignition voltage of cathode plasma is 2 kV with 5 mm gap electrode of diode and 5 ·10 -5 Tor pressure of residual gas. It is shown that carbon-fibrous cathode, made by this technology, provides more stable current take-off electron beam (withoud oscillations) in comparison with other cathodes

Development of cathode material for lithium-ion batteries

Directory of Open Access Journals (Sweden)

Rustam Mukhtaruly Turganaly

2014-08-01

Full Text Available The electrochemical characteristics of the cathode material coated with carbon layer has been developed. Various carbon coating methods. There  has been carried out a comparative electrochemical analysis of the coated and uncoated with carbon cathode material. 

Space-time-dependent development of the plasma in a pulsed hollow-cathode discharge

International Nuclear Information System (INIS)

Schaefer, G.; Wages, M.

1988-01-01

This paper presents streak camera investigations on the space-time-dependent development of pulsed hollow-cathode discharges (HCD's) starting from low-current preionization discharges. The discharges started closer to the end of the cathode, then moved further into the cathode, and then spread over a longer range along the axis of the cathode. The depth range of the intense pulsed hollow-cathode plasma was found to be two to eight times the cathode diameter

Virtual cathode regime in nonstationary electric high-current discharge in hydrogen

International Nuclear Information System (INIS)

Baksht, F.G.; Borodin, V.S.; Zhuravlev, V.N.

1988-01-01

Virtual cathode (VC) regime in a non-stationary high-current hydrogen arch is constructed. Basic calculational characteristics of the near-the-cathode layer are presented. The calculation was conducted for a 1 cm long cathode under 2x10 4 A/cm 2 current density in pulse and 10 atm. pressure. A rectangular current pulse was considered. It is shown that VC formation is caused by electron temperature reduction in the near-the-cathode area. This results in the reduction of ion flux from plasma to the cathode surface and finally in the change of a sign of space charge and field intensity near the surface. Under the transition to VC regime only the cathode temperature and its effective work function are practically changed, while the rest of parameters remain approximately constant

Electricity generation of microbial fuel cell with waterproof breathable membrane cathode

Science.gov (United States)

Xing, Defeng; Tang, Yu; Mei, Xiaoxue; Liu, Bingfeng

2015-12-01

Simplification of fabrication and reduction of capital cost are important for scale-up and application of microbial electrochemical systems (MES). A fast and inexpensive method of making cathode was developed via assembling stainless steel mesh (SSM) with waterproof breathable membrane (WBM). Three assemble types of cathodes were fabricated; Pt@SSM/WBM (SSM as cathode skeleton, WBM as diffusion layer, platinum (Pt) catalyst applied on SSM), SSM/Pt@WBM and Pt@WBM. SSM/Pt@WBM cathode showed relatively preferable with long-term stability and favorable power output (24.7 W/m3). Compared to conventional cathode fabrication, air-cathode was made for 0.5 h. The results indicated that the novel fabrication method could remarkably reduce capital cost and simplify fabrication procedures with a comparable power output, making MFC more prospective for future application.

Electrochemical Supercapacitive Performance of Spray-Deposited NiO Electrodes

Science.gov (United States)

Yadav, Abhijit A.; Chavan, U. J.

2018-04-01

Transition-metal oxides with porous structure are considered for use as promising electrodes for high-performance supercapacitors. Nanocrystalline nickel oxide (NiO) thin films have been prepared as active material for supercapacitors by spray pyrolysis. In this study, the effects of the film thickness on its structural, morphological, optical, electrical, and electrochemical properties were studied. X-ray diffraction analysis revealed cubic structure with average crystalline size of around 21 nm. Scanning electron microscopy showed porous morphology. The optical bandgap decreased from 3.04 eV to 2.97 eV with increase in the film thickness. Electrical resistivity measurements indicated semiconducting behavior. Cyclic voltammetry and galvanostatic charge/discharge study revealed good pseudocapacitive behavior. Specific capacitance of 564 F g-1 at scan rate of 5 mV s-1 and 553 F g-1 at current density of 1 A g-1 was observed. An NiO-based supercapacitor delivered specific energy of 22.8 W h kg-1 at specific power of 2.16 kW kg-1, and retained 93.01% specific capacitance at current density of 1 A g-1 after 1000 cycles. Therefore, taking advantage of the porous morphology that exists in the nanostructure, such NiO materials can be considered for use as promising electrodes for high-performance supercapacitors.

Pre-acclimation of a wastewater inoculum to cellulose in an aqueous–cathode MEC improves power generation in air–cathode MFCs

KAUST Repository

Cheng, Shaoan; Kiely, Patrick; Logan, Bruce E.

2011-01-01

-cathode MFCs with this inoculum produced maximum power densities of 1070mWm-2 (cathode surface area) in single-chamber and 880mWm-2 in two-chamber MFCs. Coulombic efficiencies ranged from 25% to 50%, and COD removals were 50-70% based on total cellulose

Thermal Characteristics of Conversion-Type FeOF Cathode in Li-ion Batteries

Directory of Open Access Journals (Sweden)

Liwei Zhao

2017-10-01

Full Text Available Rutile FeOF was used as a conversion-type cathode material for Li-ion batteries. In the present study, 0.6Li, 1.4Li, and 2.7Li per mole lithiation reactions were carried out by changing the electrochemical discharge reaction depth. The thermal characteristics of the FeOF cathode were investigated by thermogravimetric mass spectrometric (TG-MS and differential scanning calorimeter (DSC systems. No remarkable HF release was detected, even up to 700 °C, which indicated a low toxic risk for the FeOF cathode. Changes in the thermal properties of the FeOF cathode via different conversion reaction depths in the associated electrolyte were studied by changing the cathode/electrolyte ratio in the mixture. LiFeOF was found to exothermically react with the electrolyte at about 210 °C. Similar exothermic reactions were found with charged FeOF cathodes because of the irreversible Li ions. Among the products of the conversion reaction of FeOF, Li2O was found to exothermically react with the electrolyte at about 120 °C, which induced the main thermal risk of the FeOF cathode. It suggests that the oxygen-containing conversion-type cathodes have a higher thermal risk than the oxygen-free ones, but controlling the cathode/electrolyte ratio in cells successfully reduced the thermal risk. Finally, the thermal stability of the FeOF cathode was evaluated in comparison with FeF3 and LiFePO4 cathodes.

Separation of Electrolytic Reduction Product from Stainless Steel Wire Mesh Cathode Basket via Salt Draining and Reuse of the Cathode Basket

OpenAIRE

Choi, Eun-Young; Lee, Jeong; Heo, Dong Hyun; Hur, Jin-Mok

2017-01-01

We demonstrated that the metallic product obtained after electrolytic reduction (also called oxide reduction (OR)) can be simply separated from a stainless steel wire mesh cathode basket only by using a salt drain. First, the OR run of a simulated oxide fuel (0.6 kg/batch) was conducted in a molten Li2O–LiCl salt electrolyte at 650°C. The simulated oxide fuel of the porous cylindrical pellets was used as a cathode by loading a stainless steel wire mesh cathode basket. Platinum was employed as...

Bactérias amonificantes e nitrificantes e teores de amônio e nitrato afetados por plantas de cobertura e fertilizantes nitrogenados

Directory of Open Access Journals (Sweden)

Edemar Moro

2017-07-01

Full Text Available O objetivo do trabalho foi avaliar o efeito das plantas de cobertura e da fonte de nitrogênio nas bactérias nitrificantes e amonificantes do solo, bem como nos teores de nitrato e amônio. O experimento foi conduzido em um latossolo vermelho distrófico sobre sistema plantio direto (SPD por seis anos. O delineamento experimental foi em blocos casualizados, no esquema de parcelas subdivididas, com quatro repetições. As parcelas foram constituídas por seis espécies de plantas de cobertura do solo (Brachiaria brizantha, Brachiaria decumbens, Brachiaria humidicola, Brachiaria ruziziensis, Pennisetum americanum e Crotalaria spectabilis e as subparcelas pelo controle e três fontes de nitrogênio (1- controle, sem aplicação de N, 2- nitrato de cálcio, 3- sulfato de amônio e 4- sulfato de amônio + dicianodiamida (DCD aplicadas imediatamente após a emergência do arroz na dose de 40 kg ha-1 de N. Foram avaliadas a atividade das bactérias e os teores de nitrato e amônio no solo aos 15 DAE. As plantas de cobertura milheto (Pennisetum americanum, crotalaria (Crotalaria spectabilis; Brachiaria brizantha, B. decumbens; e B. humidicola proporcionaram os maiores teores de amônio no solo; O uso do inibidor de nitrificação (dicianodiamida-DCD inibiu parte das bactérias nitrificantes e proporcionou os maiores teores de amônio no solo; A atividade das bactérias amonificantes e nitrificantes foi maior nas parcelas cultivadas com braquiárias; Plantas de cobertura aliada ao uso de DCD pode ser uma estratégia para aumentar os teores de amônio do solo cultivado sobre SPD

Angle-resolved photoemission study of NiO and CoO

International Nuclear Information System (INIS)

Shen, Z.X.; Lindberg, P.A.P.; Shih, C.K.; Spicer, W.E.; Lindau, I.

1989-01-01

The authors report an angle-resolved photoemission investigation of the electronic structures of NiO and CoO. The lattice effects on the photoemission spectra of these highly correlated materials are important. The magnitudes of dispersions of the oxygen bands agree with band calculations, but the experimental data of the localized 3d bands do not agree with the band calculations

Plasma generation using the hollow cathod

International Nuclear Information System (INIS)

Moon, K.J.

1983-01-01

A hollow cathode of tungsten was adapted to an University of California, Berkely, LBL bucket ion source to investigate ion density fluctuations at the extractior grid. Fluctuations in plasma ion density are observed to range between 100kHz to 2 MHz. The observed fluctuation frequencies of plasma ion density are found to be inversely proportional to the square root of ion masses. It is guessed that the plasma fluctuation are also correlated with the hollow cathode length. (Author)

Microstructural and optical properties of Co doped NiO nanoparticles synthesized by auto combustion using NaOH as fuel

Science.gov (United States)

Parveen, Azra; Agrawal, Shraddha; Azam, Ameer

2018-05-01

The nanoparticles of 5% Co doped NiO were synthesized by auto-combustion method in aqueous medium using NaOH as a fuel. The obtained particles were characterized using X-ray diffraction studies XRD. The results of structural characterization shows the formation of Co doped Nickel oxide nanoparticles in single phase without any impurity. The optical absorption spectra of Co doped NiO sample recorded by UV-VIS spectrophotometer in the range of 200 to 800 nm have been presented. The variation of dielectric constant and dielectric loss has been studied as function of frequency. Co doping affects the optical properties and band gap. NiO can potentially be used in optical, electronic, catalytic materials, antimicrobial agent and super-paramagnetic devices.

Wire winding increases lifetime of oxide coated cathodes

Science.gov (United States)

Kerslake, W.; Vargo, D.

1965-01-01

Refractory-metal heater base wound with a thin refractory metal wire increases the longevity of oxide-coated cathodes. The wire-wound unit is impregnated with the required thickness of metal oxide. This cathode is useful in magnetohydrodynamic systems and in electron tubes.

Resistivity network and structural model of the oxide cathode for CRT application

OpenAIRE

Hashim, A. A.; Barratt, D. S.; Hassan, A. K.; Evans-Freeman, J. H.; Nabok, A.

2006-01-01

In this paper, the electrical properties of oxide cathode\\ud and oxide cathode plus, supplied by LG Philips Displays, have been\\ud investigated in relation to different cathode activation regimes and\\ud methods. Oxide cathode activation treatment for different durations\\ud has been investigated. The formations of the compounds associated\\ud to the diffusion of reducing elements (Mg, Al, and W) to the Ni cap surface of oxide cathode were studied by a new suggestion method. Scanning electron mi...

Lithium secondary batteries: Role of polymer cathode morphology

Science.gov (United States)

Naoi, Katsuhiko; Osaka, Tetsuya; Owens, Boone B.

1988-06-01

Electrically conducting polymers have been utilized both as the cathode and as the electrolyte element of Li secondary cells. Polymer cathodes were limited in their suitability for batteries because of the low energy content associated with low levels of doping and the inclusion of complex ionic species in the cathode. Recent studies have indicated that doping levels up to 100 percent can be achieved in polyanilene. High doping levels in combination with controlled morphologies have been found to improve the energy and rate capabilities of polymer cathodes. A morphology-modifying technique was utilized to enhance the charge/discharge characteristics of Li/liquid electrolyte polypyrrole cells. The polymer is electropolymerized in a preferred orientation morphology when the substrate is first precoated with an insulating film of nitrile butadiene rubber (NBR). Modification of the kinetic behavior of the electrode results from variations in the chemical composition of the NBR.

António Reis and Margarida Cordeiro, eccentric filmmakers

Directory of Open Access Journals (Sweden)

Lucas Tavares Neves

2016-02-01

Full Text Available The international symposium "António Reis and Margarida Cordeiro, eccentric filmmakers" took place in Paris between the 3rd and the 4th of June, 2015. Speakers exchanged on the political, social and poetical aspects of the duo's cinematography, as well as on the reverberations of titles such as Jaime (1974 and Trás-os-montes (1976 on the Portuguese filmic landscape of the decades that followed.

Desempenho de um filme livre de cromo na proteção contra a corrosão de ligas de alumínio 2024.

OpenAIRE

Mayra Rúbia Silva Castro

2001-01-01

Este trabalho propõe o uso de um filme preparado a partir de solução aquosa alcalina contendo íons de lítio, borato e alumínio, no sentido de inibir a corrosão de ligas de alumínio de uso aeronáutico, buscando sempre comparações com filmes de sais de cromo, atualmente utilizados. Os filmes foram obtidos por dip coating (5 minutos) e por polarização anódica (5 e 45 minutos) de ligas de alumínio 2024-T3 na solução aquosa alcalina contendo íons de lítio, borato e alumínio. Foram feitas micrograf...

Influence of the radial spacing between cathodes on the surface composition of iron samples sintered by hollow cathode electric discharge

Directory of Open Access Journals (Sweden)

Brunatto S.F.

2001-01-01

Full Text Available The present work reports an investigation of the influence of the radial spacing between cathodes on the iron sintering process by hollow cathode electrical discharge, with surface enrichment of the alloying elements Cr and Ni. Pressed cylindrical samples of 9.5 mm diameter and density of 7.0 ± 0.1 g/cm³ were prepared by compaction of Ancorsteel 1000C iron powder. These samples, constituting the central cathode, were positioned concentrically in the interior of an external cathode machined from a tube of stainless steel AISI 310 (containing: 25% Cr, 16% Ni, 1.5% Mn, 1.5% Si, 0.03% C and the remainder Fe. Sintering was done at 1150 °C, for 120 min, utilizing radial spacings between the central and hollow cathodes of 3, 6 and 9 mm and a gas mixture of 80% Ar and 20% H2, with a flow rate of 5 cm³/s at a pressure of 3 Torr. The electric discharge was generated using a pulsed voltage power source, with a period of 200 mus. The radial spacing had only a slight influence on the quantity of atoms of alloying elements deposited and diffused on the surface of the sample. Analysis with a microprobe showed the presence of chrome (up to 4.0% and nickel (up to 3.0%, in at. % at the surface of the samples. This surface enrichment can be attributed to the mechanism of sputtering of the metallic atoms present in the external cathode, with the deposition of these elements on the sample surface and consequent diffusion within the sample.

Mathematical micro-model of a solid oxide fuel cell composite cathode

International Nuclear Information System (INIS)

Kenney, B.; Karan, K.

2004-01-01

In a solid oxide fuel cell (SOFC), the cathode processes account for a majority of the overall electrochemical losses. A composite cathode comprising a mixture of ion-conducting electrolyte and electron-conducting electro-catalyst can help minimize cathode losses provided microstructural parameters such as particle-size, composition, and porosity are optimized. The cost of composite cathode research can be greatly reduced by incorporating mathematical models into the development cycle. Incorporated with reliable experimental data, it is possible to conduct a parametric study using a model and the predicted results can be used as guides for component design. Many electrode models treat the cathode process simplistically by considering only the charge-transfer reaction for low overpotentials or the gas-diffusion at high overpotentials. Further, in these models an average property of the cathode internal microstructure is assumed. This paper will outline the development of a 1-dimensional SOFC composite cathode micro-model and the experimental procedures for obtaining accurate parameter estimates. The micro-model considers the details of the cathode microstructure such as porosity, composition and particle-size of the ionic and electronic phases, and their interrelationship to the charge-transfer reaction and mass transport processes. The micro-model will be validated against experimental data to determine its usefulness for performance prediction. (author)

Characterization of scandia doped pressed cathode fabricated by spray drying method

International Nuclear Information System (INIS)

Cui Yuntao; Wang Jinshu; Liu Wei; Wang Yiman; Zhou Meiling

2011-01-01

Scandia doped pressed cathode was prepared by a new method of spray drying combined with two-step hydrogen reduction process. The Sc 2 O 3 and barium-calcium aluminate co-doped powders have sub-micrometer size in the range of 0.1-1 μm and scandium oxide and barium-calcium aluminate are distributed evenly in the powders. The cathodes sintered by powder metallurgy at 1600 deg. C b have a smooth surface and sub-micrometer grain structure with homogeneous distribution of scandium, barium, calcium and aluminum which are dispersed over and among the tungsten grains. This cathode has good emission, e.g., the current density of this cathode reaches 31.50 A/cm 2 at 850 deg. C b . After proper activation, the cathode surface is covered by a Ba-Sc-O active substances layer with a preferable atomic ratio, leading to its good emission property. The evaporation activation energy of SDP cathode with 4.58 eV is the highest among the Ba-W, M-type and SDP cathodes, and the average evaporation velocity v t of SDP cathode with 1.28 x 10 -8 g cm -2 s -1 at 1150 deg. C b is the lowest one.

Back bombardment for dispenser and lanthanum hexaboride cathodes

Directory of Open Access Journals (Sweden)

Mahmoud Bakr

2011-06-01

Full Text Available The back bombardment (BB effect limits wide usage of thermionic rf guns. The BB effect induces not only ramping-up of a cathode’s temperature and beam current, but also degradation of cavity voltage and beam energy during a macropulse. This paper presents a comparison of the BB effect for the case of dispenser tungsten-base (DC and lanthanum hexaboride (LaB_{6} thermionic rf gun cathodes. For each, particle simulation codes are used to simulate the BB effect and electron beam dynamics in a thermionic rf gun cathode. A semiempirical equation is also used to investigate the stopping range and deposited heat power of BB electrons in the cathode material. A numerical simulation method is used to calculate the change of the cathode temperature and current density during a single macropulse. This is done by solving two differential equations for the rf gun cavity equivalent circuit and one-dimensional thermal diffusion equation. High electron emission and small beam size are required for generation of a high-brightness electron beam, and so in this work the emission properties of the cathode are taken into account. Simulations of the BB effect show that, for a pulse of 6  μs duration, the DC cathode experiences a large change in the temperature compared with LaB_{6}, and a change in current density 6 times higher. Validation of the simulation results is performed using experimental data for beam current beyond the gun exit. The experimental data is well reproduced using the simulation method.

Improved Electrochromic Characteristics of a Honeycomb-Structured Film Composed of NiO.

Science.gov (United States)

Yang, Hyeeun; Lee, Yulhee; Kim, Dong In; Seo, Hyeon Jin; Yu, Jung-Hoon; Nam, Sang-Hun; Boo, Jin-Hyo

2018-09-01

Color changes controlled by electronic energies have been studied for many years in order to fabricate energy-efficient smart windows. Reduction and oxidization of nickel oxide under the appropriate voltage can change the color of a window. For a superior nickel oxide (NiO) electrochromic device (ECD), it is important to control the chemical and physical characteristics of the surface. In this study, we applied polystyrene bead templates to nickel oxide films to fabricate a honeycomb-structured electrochromic (EC) layer. We synthesized uniform polystyrene beads using the chemical wet method and placed them on substrates to create honeycomb-structured NiO films. Then, the EC characteristics of the nickel oxide films with a honeycomb structure were evaluated with UV-Visible and cyclic voltammetry. FE-SEM and AFM were used to measure the morphologies of the nanostructures and the efficiencies of the redox reactions related to the specific surface area.

O diabo em Antônio José da Silva, o Judeu

Directory of Open Access Journals (Sweden)

Kênia Maria de Almeida Pereira

2009-10-01

Full Text Available A novela Obras do diabinho da mão furada, escrito no século 18, por Antônio José da Silva, o Judeu, apareceu pela primeira vez em Portugal em forma de cordel. Percebe-­se, em sua composição, uma polifonia que mescla fontes populares e eruditas. O autor tece sua narrativa com fios emprestados das aventuras do Doutor Fausto às voltas com pactos, diabos, bruxas, além de referências acadêmicas e clássicas, como a Bíblia, a Divina Comédia, de Dante, e Dom Quixote, de Cervantes. Nas entrelinhas dessa narrativa, e em meio às urdiduras de suas metáforas intrigantes, Antônio José introduz severas críticas à sociedade lisboeta e à intolerância da Santa Inquisição Portuguesa.

Development of multi-pixel x-ray source using oxide-coated cathodes.

Science.gov (United States)

Kandlakunta, Praneeth; Pham, Richard; Khan, Rao; Zhang, Tiezhi

2017-07-07

Multiple pixel x-ray sources facilitate new designs of imaging modalities that may result in faster imaging speed, improved image quality, and more compact geometry. We are developing a high-brightness multiple-pixel thermionic emission x-ray (MPTEX) source based on oxide-coated cathodes. Oxide cathodes have high emission efficiency and, thereby, produce high emission current density at low temperature when compared to traditional tungsten filaments. Indirectly heated micro-rectangular oxide cathodes were developed using carbonates, which were converted to semiconductor oxides of barium, strontium, and calcium after activation. Each cathode produces a focal spot on an elongated fixed anode. The x-ray beam ON and OFF control is performed by source-switching electronics, which supplies bias voltage to the cathode emitters. In this paper, we report the initial performance of the oxide-coated cathodes and the MPTEX source.

An explosive-emitter cathode produced using the heavy ion track technique

International Nuclear Information System (INIS)

Akap'ev, G.N.; Korenev, S.A.

1988-01-01

A cathode based on thin metallic foils with a homogeneous needle surface is described. The cathode was manufactured using the heavy ion track technique which permits the production of cathodes with an unlimited area and a needle density ranging from about 10 3 to 10 9 needles per cm 2 . An electron gun using this type of cathode has a current of 200-900 A and an energy of 100-300 keV. The cross section of the electron beam is fairly uniform. It is shown that needle emitters of similar shape and size play the principal role in forming a homogeneous cathode plasma

Formation of virtual cathodes and microwave generation in relativistic electron beams

International Nuclear Information System (INIS)

Kwan, T.J.T.; Thode, L.E.

1984-01-01

Simulation of the generation of a relativistic electron beam in a foil diode configuration and the subsequent intense microwave generation resulting from the formation of the virtual cathode is presented. The oscillating virtual cathode and the trapped beam electrons between the real and the virtual cathodes were found to generate microwaves at two distinct frequencies. Generation of high-power microwaves with about 10% efficiency might reasonably be expected from such a virtual-cathode configuration

Lipon coatings for high voltage and high temperature Li-ion battery cathodes

Energy Technology Data Exchange (ETDEWEB)

Dudney, Nancy J.; Liang, Chengdu; Nanda, Jagjit; Veith, Gabriel M.; Kim, Yoongu; Martha, Surendra Kumar

2017-12-05

A lithium ion battery includes an anode and a cathode. The cathode includes a lithium, manganese, nickel, and oxygen containing compound. An electrolyte is disposed between the anode and the cathode. A protective layer is deposited between the cathode and the electrolyte. The protective layer includes pure lithium phosphorus oxynitride and variations that include metal dopants such as Fe, Ti, Ni, V, Cr, Cu, and Co. A method for making a cathode and a method for operating a battery are also disclosed.

In Situ Synthesis of Vertical Standing Nanosized NiO Encapsulated in Graphene as Electrodes for High-Performance Supercapacitors.

Science.gov (United States)

Lin, Jinghuang; Jia, Henan; Liang, Haoyan; Chen, Shulin; Cai, Yifei; Qi, Junlei; Qu, Chaoqun; Cao, Jian; Fei, Weidong; Feng, Jicai

2018-03-01

NiO is a promising electrode material for supercapacitors. Herein, the novel vertically standing nanosized NiO encapsulated in graphene layers (G@NiO) are rationally designed and synthesized as nanosheet arrays. This unique vertical standing structure of G@NiO nanosheet arrays can enlarge the accessible surface area with electrolytes, and has the benefits of short ion diffusion path and good charge transport. Further, an interconnected graphene conductive network acts as binder to encapsulate the nanosized NiO particles as core-shell structure, which can promote the charge transport and maintain the structural stability. Consequently, the optimized G@NiO hybrid electrodes exhibit a remarkably enhanced specific capacity up to 1073 C g -1 and excellent cycling stability. This study provides a facial strategy to design and construct high-performance metal oxides for energy storage.

Mosaic-shaped cathode for highly durable solid oxide fuel cell under thermal stress

Science.gov (United States)

Joo, Jong Hoon; Jeong, Jaewon; Kim, Se Young; Yoo, Chung-Yul; Jung, Doh Won; Park, Hee Jung; Kwak, Chan; Yu, Ji Haeng

2014-02-01

In this study, we propose a novel "mosaic structure" for a SOFC (solid oxide fuel cell) cathode with high thermal expansion to improve the stability against thermal stress. Self-organizing mosaic-shaped cathode has been successfully achieved by controlling the amount of binder in the dip-coating solution. The anode-supported cell with mosaic-shaped cathode shows itself to be highly durable performance for rapid thermal cycles, however, the performance of the cell with a non-mosaic cathode exhibits severe deterioration originated from the delamination at the cathode/electrolyte interface after 7 thermal cycles. The thermal stability of an SOFC cathode can be evidently improved by controlling the surface morphology. In view of the importance of the thermal expansion properties of the cathode, the effects of cathode morphology on the thermal stress stability are discussed.

Modular cathode assemblies and methods of using the same for electrochemical reduction

Science.gov (United States)

Wiedmeyer, Stanley G.; Barnes, Laurel A.; Williamson, Mark A.; Willit, James L.

2018-03-20

Modular cathode assemblies are useable in electrolytic reduction systems and include a basket through which fluid electrolyte may pass and exchange charge with a material to be reduced in the basket. The basket can be divided into upper and lower sections to provide entry for the material. Example embodiment cathode assemblies may have any shape to permit modular placement at any position in reduction systems. Modular cathode assemblies include a cathode plate in the basket, to which unique and opposite electrical power may be supplied. Example embodiment modular cathode assemblies may have standardized electrical connectors. Modular cathode assemblies may be supported by a top plate of an electrolytic reduction system. Electrolytic oxide reduction systems are operated by positioning modular cathode and anode assemblies at desired positions, placing a material in the basket, and charging the modular assemblies to reduce the metal oxide.

Coating for lithium anode, thionyl chloride active cathode electrochemical cell

Energy Technology Data Exchange (ETDEWEB)

Catanzarite, V.O.

1983-01-04

Electrochemical power cells having a cathode current collector, a combination liquid active cathode depolarizer electrolyte solvent and an anode that forms surface compounds when in intimate contact with the liquid cathode are enhanced by the addition of a passivation limiting film contiguous to said anode. The passivating film is a member of the cyanoacrilate family of organic compounds.

Coating for lithium anode, thionyl chloride active cathode electrochemical cell

Energy Technology Data Exchange (ETDEWEB)

Catanzarite, V.O.

1981-10-20

Electrochemical power cells having a cathode current collector, a combination liquid active cathode depolarizer electrolyte solvent and an anode that forms surface compounds when in intimate contact with the liquid cathode are enhanced by the addition of a passivation limiting film contiguous to said anode. The passivating film is a member of the cyanoacrilate family of organic compounds.

Magnetic dichroism and spin structure of antiferromagnetic NiO(001) films

NARCIS (Netherlands)

Altieri, S; Finazzi, M; Hsieh, HH; Lin, HJ; Chen, CT; Hibma, T; Valeri, S; Sawatzky, GA

2003-01-01

We find that Ni L-2 edge x-ray magnetic linear dichroism is fully reversed for NiO(001) films on materials with reversed lattice mismatch. We relate this phenomenon to a preferential stabilization of magnetic S domains with main spin component either in or out of the plane, via dipolar interactions.

Photoelectron spectroscopy study on Li substituted NiO using PES beamline installed on Indus-1

CERN Document Server

Banerjee, A; Phase, D M; Dasannacharya, B A

2003-01-01

Photoelectron spectroscopy beamline based on a toroidal grating monochromator (TGM) is recently commissioned on Indus-1 storage ring. It has been used to carry out valence band photoemission study of Li substituted NiO. In this paper initially a brief description of the beamline components and the experimental station for angle integrated photoemission experiment is presented. The later part of this paper is devoted to studies carried out on Li sub x Ni sub 1 sub - sub x O with x=0.0, 0.35 and 0.5 samples. Thin pellets of polycrystalline samples were used for the measurements reported here. Valence band spectra recorded on polycrystalline Li sub x Ni sub 1 sub - sub x O samples show drastic changes in various features as compared to that of pure NiO. The prominent changes are: (i) change in the relative contributions of Ni-3d and O-2p emissions, (ii) change in the peak position of Ni-3d from the top of the valance band of NiO and (iii) no noticeable change in the Ni satellite peak. These results are evaluated...

EFEITO SECUNDÁRIO DO BURACO DE OZÔNIO ANTÁRTICO SOBRE O SUL DO BRASIL

OpenAIRE

Lucas Vaz Peres

2013-01-01

Na presente Dissertação foram identificados os eventos de Efeito Secundário do Buraco de Ozônio Antártico ocorridos sobre o Sul do Brasil no período entre 1979 e 2011. Para isso, foram analisados os dados médios diários da coluna total de ozônio obtidos através dos Espectrofotômetros Brewer modelo MKIV #081 durante o período de 1992 2000, modelo MKII #056 de 2000 2002 e modelo MKIII #167 de 2002 até os dias atuais, instalados no Observatório Espacial do Sul OES/CRS/INPE MCTI (29,4 S; 53,8...

Oxide-cathode activation and surface temperature calculation of electron cooler

International Nuclear Information System (INIS)

Li Jie; Yang Xiaodong; Mao Lijun; Li Guohong; Yuan Youjin; Liu Zhanwen; Zhang Junhui; Yang Xiaotian; Ma Xiaoming; Yan Tailai

2011-01-01

The pollution on electron gun ceramic insulation of electron cooler restricted the operation of electron cooler at HIRFL-CSR main ring. To cool and accumulate ion beam well, the pollution was cleared and a new oxide-coated cathode was assembled. The processes of cathode replacement,vacuum chamber baking-out, and thermal decomposition of coating binders and alkaline earth metal carbonates, and cathode activation are presented. The electron gun perveance of 10.6 μA/V 1.5 was attained under the heating power of 60 W. The typical surface temperature of oxide-coated cathode that is calculated through grey-body radiation is 1 108 K which shows a comparable result to the experimental measurement 1 078 K. The perveance growth of electron gun during the electron cooler operation is also explained by partial activation of the cathode. (authors)

Theory of hollow cathode arc discharges. II. Metastable state balance inside the cathode. Application to argon

International Nuclear Information System (INIS)

Ferreira, C.M.; Delcroix, J.L.

1975-01-01

In the hollow cathode the metastable species are created by fast electrons, which are emitted by the cathode wall and injected in the plasma across a space-charge sheath, and destroyed by Maxwellian electrons. A detailed analysis of the different electronic destruction mechanisms in argon shows that the re-excitation up to 3p 5 4p states plays a very important role. Solutions of the metastable balance equation were obtained in a wide range of variation of the discharge parameters displaying the best conditions of operation to obtain high concentrations [fr

Modelling current transfer to cathodes in metal halide plasmas

International Nuclear Information System (INIS)

Benilov, M S; Cunha, M D; Naidis, G V

2005-01-01

This work is concerned with investigation of the main features of current transfer to cathodes under conditions characteristic of metal halide (MH) lamps. It is found that the presence of MHs in the gas phase results in a small decrease of the cathode surface temperature and of the near-cathode voltage drop in the diffuse mode of current transfer; the range of stability of the diffuse mode expands. Effects caused by a variation of the work function of the cathode surface owing to formation of a monolayer of alkali metal atoms on the surface are studied for particular cases where the monolayer is composed of sodium or caesium. It is found that the formation of the sodium monolayer affects the diffuse mode of current transfer only moderately and in the same direction that the presence of metal atoms in the gas phase affects it. Formation of the caesium monolayer produces a dramatic effect: the cathode surface temperature decreases very strongly, the diffuse-mode current-voltage characteristic becomes N-S-shaped

Durability and Performance of High Performance Infiltration Cathodes

DEFF Research Database (Denmark)

Samson, Alfred Junio; Søgaard, Martin; Hjalmarsson, Per

2013-01-01

The performance and durability of solid oxide fuel cell (SOFC) cathodes consisting of a porous Ce0.9Gd0.1O1.95 (CGO) infiltrated with nitrates corresponding to the nominal compositions La0.6Sr0.4Co1.05O3-δ (LSC), LaCoO3-δ (LC), and Co3O4 are discussed. At 600°C, the polarization resistance, Rp......, varied as: LSC (0.062Ωcm2)cathode was found to depend on the infiltrate firing temperature and is suggested to originate...... of the infiltrate but also from a better surface exchange property. A 450h test of an LSC-infiltrated CGO cathode showed an Rp with final degradation rate of only 11mΩcm2kh-1. An SOFC with an LSC-infiltrated CGO cathode tested for 1,500h at 700°C and 0.5Acm-2 (60% fuel, 20% air utilization) revealed no measurable...

Beam Dynamics Simulations of Optically-Enhanced Field Emission from Structured Cathodes

Energy Technology Data Exchange (ETDEWEB)

Seymour, A. [Northern Illinois U.; Grote, D. [LLNL, Livermore; Mihalcea, D. [Northern Illinois U.; Piot, P. [Fermilab; Vay, J.-L. [LBNL, Berkeley

2014-01-01

Structured cathodes - cathodes with a segmented emission surface - are finding an increasing number of applications and can be combined with a variety of emission mechanisms, including photoemission and field emission. These cathodes have been used to enhance the quantum efficiency of metallic cathodes when operated as plasmonic cathodes, have produced high-current electron bunches though field emission from multiple tips, and can be used to form beams with transverse segmentations necessary for improving the performance of accelerator-based light sources. In this report we present recent progress towards the development of finite-difference time-domain particle-in-cell simulations using the emission process in structured cathodes based on the WARP framework. The simulations give further insight on the localized source of the emitted electrons which could be used for additional high-fidelity start-to-end simulations of electron accelerators that employ this type of electron source.

Vacuum-Free, Maskless Patterning of Ni Electrodes by Laser Reductive Sintering of NiO Nanoparticle Ink and Its Application to Transparent Conductors

KAUST Repository

Lee, Daeho; Paeng, Dongwoo; Park, Hee K.; Grigoropoulos, Costas P.

2014-01-01

© 2014 American Chemical Society. We introduce a method for direct patterning of Ni electrodes through selective laser direct writing (LDW) of NiO nanoparticle (NP) ink. High-resolution Ni patterns are generated from NiO NP thin films by a vacuum

Uniform magnetic excitations in NiO nanoparticles

DEFF Research Database (Denmark)

Bahl, C.R.H.; Kuhn, L.T.; Lefmann, K.

2006-01-01

A sample of isolated disc shaped NiO nanoparticles was studied at the RITA-II triple axis spectrometer at SINQ (PSI) using the newly implemented multi-analyser blade imaging mode. The particles were 13 nm in diameter and had a thickness of about 2.5 nm. A non-dispersive spin excitation was observed...... at the antiferromagnetic ((1)/(2) (1)/(2) (1)/(2)) reflection at a scattering vector of kappa = 1.30 angstrom(-1), at an energy of 2 0.51 +/- 0.02 meV. This is shown to be due to uniform magnetic excitations in the nanoparticles. (c) 2006 Elsevier B.V. All rights reserved....

Impact of cathode evaporation on a free-burning arc

International Nuclear Information System (INIS)

Etemadi, K.

1990-01-01

In the center of a free-burning, high intensity argon arc at atmospheric pressure, a highly ionized vapor beam of copper has been generated by a continuous feeding of a thin (0.5 and 1 mm diameter) copper wire to the hot surface region of the cathode in the vicinity of the plasma attachment. The copper vapor is carried into the plasma column between the electrodes by the self-magnetic induced plasma flow caused by the conical shape of the cathode. In order to study the vapor beam, the arc is modeled at atmospheric pressure, with a current of 150 A, a gap spacing of 1 cm, a cathode tip of 60 degrees and a copper vapor flow of 1 mg/s. The temperature, mass flow, current flow and Cu concentration are calculated for the entire plasma region. The intensity distribution of CuI spectral line at 5218.2 angstrom is also recorded by emission spectroscopy and compared with the calculated values. The copper vapor in the cathode region has velocities of 210 m/s with a mass concentration of above 90% within 0.5 mm from the arc axis. The vapor passes from the cathode toward the anode with a slight diffusion in the argon plasma. Higher temperatures and current densities in the core of the arc, caused by the cathode evaporation, are calculated

Development of alloy-film coated dispenser cathode for terahertz vacuum electron devices application

International Nuclear Information System (INIS)