Excessive nickel release from mobile phones--a persistent cause of nickel allergy and dermatitis.

Science.gov (United States)

Jensen, Peter; Johansen, Jeanne D; Zachariae, Claus; Menné, Torkil; Thyssen, Jacob P

2011-12-01

Despite the political intention to limit nickel allergy and dermatitis in Europeans, nickel allergy remains frequent. There are several explanations for the persistence of nickel allergy and dermatitis, including the increasing use of mobile phones. Before regulation of nickel release from mobile phones, we showed that eight (19.5%) of 41 mobile phones marketed in Denmark between 2003 and 2007 released nickel in concentrations that may result in nickel allergy and dermatitis. In 2009, the EU Nickel Directive was revised to include nickel-releasing mobile phones. To investigate the proportion of mobile phones sold in Denmark that release nickel after regulation. Metallic parts from 50 randomly selected mobile phones currently for sale in Denmark were tested for nickel release by use of the dimethylglyoxime (DMG)-nickel spot test. Nine (18%) phones showed at least one positive DMG test reaction and two phones had more than one DMG test-positive spot. Apparently, the proportion of mobile phones with significant nickel release remains unchanged, despite the 2009 revision of the EU Nickel Directive. We encourage manufacturers to measure nickel release from metallic components used in the assembly of mobile phones to ensure safe products. © 2011 John Wiley & Sons A/S.

Complexation-Based Detection of Nickel(II) at a Graphene-Chelate Probe in the Presence of Cobalt and Zinc by Adsorptive Stripping Voltammetry.

Science.gov (United States)

Pokpas, Keagan; Jahed, Nazeem; Baker, Priscilla G; Iwuoha, Emmanuel I

2017-07-25

The adsorptive stripping voltammetric detection of nickel and cobalt in water samples at metal film electrodes has been extensively studied. In this work, a novel, environmentally friendly, metal-free electrochemical probe was constructed for the ultra-trace determination of Ni 2+ in water samples by Adsorptive Cathodic Stripping Voltammetry (AdCSV). The electrochemical platform is based on the adsorptive accumulation of Ni 2+ ions directly onto a glassy carbon electrode (GCE) modified with dimethylglyoxime (DMG) as chelating agent and a Nafion-graphene (NGr) nanocomposite to enhance electrode sensitivity. The nafion-graphene dimethylglyoxime modified glassy carbon electrode (NGr-DMG-GCE) shows superior detection capabilities as a result of the improved surface-area-to-volume ratio and enhanced electron transfer kinetics following the incorporation of single layer graphene, while limiting the toxic effects of the sensor by removal of the more common mercury, bismuth and lead films. Furthermore, for the first time the NGr-DMG-GCE, in the presence of common interfering metal ions of Co 2+ and Zn 2+ demonstrates good selectivity and preferential binding towards the detection of Ni 2+ in water samples. Structural and morphological characterisation of the synthesised single layer graphene sheets was conducted by Raman spectrometry, HRTEM and HRSEM analysis. The instrumental parameters associated with the electrochemical response, including accumulation potential and accumulation time were investigated and optimised in addition to the influence of DMG and graphene concentrations. The NGr-DMG-GCE demonstrated well resolved, reproducible peaks, with RSD (%) below 5% and a detection limit of 1.5 µg L -1 for Ni 2+ reduction at an accumulation time of 120 s., the prepared electrochemical sensor exhibited good detection and quantitation towards Ni 2+ detection in tap water samples, well below 0.1 mg L -1 set by the WHO and EPA standards. This comparable to the South African

Identification of metallic items that caused nickel dermatitis in Danish patients.

Science.gov (United States)

Thyssen, Jacob P; Menné, Torkil; Johansen, Jeanne D

2010-09-01

Nickel allergy is prevalent as assessed by epidemiological studies. In an attempt to further identify and characterize sources that may result in nickel allergy and dermatitis, we analysed items identified by nickel-allergic dermatitis patients as causative of nickel dermatitis by using the dimethylglyoxime (DMG) test. Dermatitis patients with nickel allergy of current relevance were identified over a 2-year period in a tertiary referral patch test centre. When possible, their work tools and personal items were examined with the DMG test. Among 95 nickel-allergic dermatitis patients, 70 (73.7%) had metallic items investigated for nickel release. A total of 151 items were investigated, and 66 (43.7%) gave positive DMG test reactions. Objects were nearly all purchased or acquired after the introduction of the EU Nickel Directive. Only one object had been inherited, and only two objects had been purchased outside of Denmark. DMG testing is valuable as a screening test for nickel release and should be used to identify relevant exposures in nickel-allergic patients. Mainly consumer items, but also work tools used in an occupational setting, released nickel in dermatitis patients. This study confirmed 'risk items' from previous studies, including mobile phones.

Nickel release from inexpensive jewelry and hair clasps purchased in an EU country - Are consumers sufficiently protected from nickel exposure?

DEFF Research Database (Denmark)

Thyssen, Jacob Pontoppidan; Menné, Torkil; Johansen, Jeanne Duus

2009-01-01

BACKGROUND: Nickel allergic subjects are at risk factor of acquiring hand eczema. In 1990 and 1994, respectively, Denmark and member states in the EU regulated nickel release from selected consumer products. The intention was that the nickel epidemic could be controlled and prevented if the general...... population was protected from high cutaneous nickel concentrations. Despite a decrease, the prevalence of nickel allergy remains high as nearly 10% of young women are nickel allergic. OBJECTIVE: This study aimed to perform dimethylglyoxime (DMG) testing of inexpensive jewelry and hair clasps purchased from...

Complexation-Based Detection of Nickel(II at a Graphene-Chelate Probe in the Presence of Cobalt and Zinc by Adsorptive Stripping Voltammetry

Directory of Open Access Journals (Sweden)

Keagan Pokpas

2017-07-01

Full Text Available The adsorptive stripping voltammetric detection of nickel and cobalt in water samples at metal film electrodes has been extensively studied. In this work, a novel, environmentally friendly, metal-free electrochemical probe was constructed for the ultra-trace determination of Ni2+ in water samples by Adsorptive Cathodic Stripping Voltammetry (AdCSV. The electrochemical platform is based on the adsorptive accumulation of Ni2+ ions directly onto a glassy carbon electrode (GCE modified with dimethylglyoxime (DMG as chelating agent and a Nafion-graphene (NGr nanocomposite to enhance electrode sensitivity. The nafion-graphene dimethylglyoxime modified glassy carbon electrode (NGr-DMG-GCE shows superior detection capabilities as a result of the improved surface-area-to-volume ratio and enhanced electron transfer kinetics following the incorporation of single layer graphene, while limiting the toxic effects of the sensor by removal of the more common mercury, bismuth and lead films. Furthermore, for the first time the NGr-DMG-GCE, in the presence of common interfering metal ions of Co2+ and Zn2+ demonstrates good selectivity and preferential binding towards the detection of Ni2+ in water samples. Structural and morphological characterisation of the synthesised single layer graphene sheets was conducted by Raman spectrometry, HRTEM and HRSEM analysis. The instrumental parameters associated with the electrochemical response, including accumulation potential and accumulation time were investigated and optimised in addition to the influence of DMG and graphene concentrations. The NGr-DMG-GCE demonstrated well resolved, reproducible peaks, with RSD (% below 5% and a detection limit of 1.5 µg L−1 for Ni2+ reduction at an accumulation time of 120 s., the prepared electrochemical sensor exhibited good detection and quantitation towards Ni2+ detection in tap water samples, well below 0.1 mg L−1 set by the WHO and EPA standards. This comparable to the South

Radiochemical procedure and quantitative determination of the activation product, 63Ni, in environmental soft water samples with high Ca and Mg phosphate concentration

International Nuclear Information System (INIS)

Jordan, N.; Michel, H.; Barci-Funel, G.; Barci, V.

2008-01-01

Nickel-63 is a low energy beta-emitter needing a radiochemical separation before β-counting. Several papers described the separation and the detection of 63 Ni in environmental samples. The method used in our work was first developed by SKWARZEC and HOLM. The main steps of this separation are the selective precipitation of nickel with dimethylglyoxime (DMG) and the use of the non-sorption of nickel on anion resin in hydrochloric acid solutions. In this paper, a new step is added to eliminate high quantities of calcium and magnesium phosphate disturbing the iron hydroxide precipitation step. The procedure has been applied to soft water samples: sediments, plants and fishes. The chemical yields are 60, 70 and 20%, respectively. The detection limit of 63 Ni by liquid scintillation spectrometer is 10 mBq. (author)

Nickel speciation and complexation kinetics in freshwater by ligand exchange and DPCSV

NARCIS (Netherlands)

Han Bin Xue,; Jansen, S.; Prasch, A.; Sigg, L.

2001-01-01

A technique of ligand exchange with DMG (dimethylglyoxime) and DPCSV was applied to determine Ni speciation in lake, river, and groundwater samples. The working conditions related to ligand-exchange equilibrium were optimized, and the ligand-exchange kinetics were examined. The observed

Nickel on the market: a baseline survey of articles in 'prolonged contact' with skin.

Science.gov (United States)

Ringborg, Evelina; Lidén, Carola; Julander, Anneli

2016-08-01

In April 2014, the European Chemicals Agency defined the concept of 'prolonged contact with skin' as used in the EU nickel restriction. To establish a baseline of nickel-releasing items on the Swedish market conforming with the EU nickel restriction according to the definition of 'prolonged contact' with the skin. We performed a limited market survey in Stockholm, Sweden. Items with metallic parts that come into contact with the skin, except those explicitly mentioned in the legal text, were chosen. The dimethylglyoxime (DMG) test was used to evaluate nickel release. One hundred and forty-one items belonging to one of three categories - accessories, utensils for needlework, painting and writing (called utensils), and electronic devices - were tested in the study. Forty-four percent of all items were DMG test-positive (releasing nickel), and 9% gave a doubtful DMG test result. The large proportion of nickel-releasing items in the present study shows clearly that broader parts of industry need to take action to prevent nickel allergy. The high proportion of DMG test-positive items indicates that there is still much work to be done to reduce the nickel exposure of the population. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Ferromagnetic Coupling between Copper(II) Centers through the Diamagnetic Zinc(II) Ion: Crystal Structure and Magnetic Properties of [Cu(2)Zn(Hdmg)(2)(dmg)(2)(H(2)O)].0.5H(2)dmg.H(2)O (H(2)dmg = Dimethylglyoxime).

Science.gov (United States)

Ruiz, Rafael; Julve, Miguel; Faus, Juan; Lloret, Francesc; Muñoz, M. Carmen; Journaux, Yves; Bois, Claudette

1997-07-30

A new heterotrinuclear complex of formula [Cu(2)Zn(Hdmg)(2)(dmg)(2)(H(2)O)].0.5H(2)dmg.H(2)O (C(18)H(34)Cu(2)N(9)O(11)Zn, 1) (H(2)dmg = dimethylglyoxime) has been synthesized and its crystal structure determined by single-crystal X-ray diffraction. It crystallizes in the triclinic system, space group P&onemacr;, with a = 11.414(1) Å, b = 11.992(3) Å, c =12.567(10) Å, alpha = 91.27(6) degrees, beta = 111.46(2) degrees, gamma = 112.24(2) degrees, and Z = 2. The structure consists of a chain of neutral [Cu(2)Zn(Hdmg)(2)(dmg)(2)(H(2)O)] trinuclear units and noncoordinated H(2)dmg and water molecules. The configuration around the zinc atom is distorted trigonal bipyramidal with four oximate oxygens from two [Cu(Hdmg)(dmg)](-) fragments (each one acting as a bidentate ligand through its deprotonated oximate oxygens in cis positions) occupying one axial and the three equatorial positions and an additional oximate oxygen from a symmetry-related [Cu(Hdmg)(dmg)](-) fragment filling the remaining axial position. The environment around Cu(1) and Cu(2) is distorted square pyramidal with four oximate nitrogen atoms building the equatorial plane. An oxygen atom [O(9)] from a water molecule and an oximate oxygen from a symmetry-related [Cu(Hdmg)(dmg)](-) fragment occupy the apical position of the square pyramids around Cu(1) and Cu(2), respectively. The trinuclear units are repeated through inversion centers standing at the middle of the Zn(1).Zn(1)(i) and Cu(2).Cu(2)(ii) vectors leading to a chain which runs parallel to the diagonal of the ac-plane. The Cu(1).Cu(2), Zn(1).Zn(1)(i), and Cu(2).Cu(2)(ii) separations are 5.506(2), 3.390(2), and 3.930(2) Å, respectively. 1 exhibits a characteristic ferromagnetic behavior with a continuous increase of the chi(M)T product as the temperature is lowered from 300 to 2.0 K. The field dependence of the magnetization at 2.0 K is consistent with a low-lying quintet state. The only efficient exchange pathways responsible for the overall

Excessive nickel release from earrings purchased from independent shops and street markets--a field study from Warsaw and London.

Science.gov (United States)

Thyssen, J P; Menné, T; Lidén, C; White, I R; White, J; Spiewak, R; Johansen, J D

2011-09-01

Nickel allergy is frequent and cause morbidity and increased health care costs. The aim of this study was to determine the proportion of inexpensive earrings randomly purchased from stores and street markets in two capitals that gave positive dimethylglyoxime (DMG) test reactions and to determine whether the degree of nickel release was related to shop category. Random inexpensive metallic earrings were purchased from stores and vendors in London and Warsaw. A qualitative investigation of nickel release by using the DMG test was performed. DMG testing revealed that respectively 15.1% (n=205) and 18.4% (n=206) of earrings purchased in London and Warsaw released nickel as indicated by positive test outcomes. Stratification by store category showed that DMG test-positive jewellery were mainly purchased from street markets and from stores that were not part of national or international chains. Despite the EU Nickel Directive having resulted in decreasing prevalence of nickel allergy, a large proportion of inexpensive earrings still release nickel in concentrations that may result in nickel allergy and dermatitis. Authorities should prioritize information campaigns and random inspections as a legislation that is not followed is of limited value. © 2010 The Authors. Journal of the European Academy of Dermatology and Venereology © 2010 European Academy of Dermatology and Venereology.

Nickel and cobalt release from jewellery and metal clothing items in Korea.

Science.gov (United States)

Cheong, Seung Hyun; Choi, You Won; Choi, Hae Young; Byun, Ji Yeon

2014-01-01

In Korea, the prevalence of nickel allergy has shown a sharply increasing trend. Cobalt contact allergy is often associated with concomitant reactions to nickel, and is more common in Korea than in western countries. The aim of the present study was to investigate the prevalence of items that release nickel and cobalt on the Korean market. A total of 471 items that included 193 branded jewellery, 202 non-branded jewellery and 76 metal clothing items were sampled and studied with a dimethylglyoxime (DMG) test and a cobalt spot test to detect nickel and cobalt release, respectively. Nickel release was detected in 47.8% of the tested items. The positive rates in the DMG test were 12.4% for the branded jewellery, 70.8% for the non-branded jewellery, and 76.3% for the metal clothing items. Cobalt release was found in 6.2% of items. Among the types of jewellery, belts and hair pins showed higher positive rates in both the DMG test and the cobalt spot test. Our study shows that the prevalence of items that release nickel or cobalt among jewellery and metal clothing items is high in Korea. © 2013 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Occupational hand eczema caused by nickel and evaluated by quantitative exposure assessment.

Science.gov (United States)

Jensen, Peter; Thyssen, Jacob P; Johansen, Jeanne D; Skare, Lizbet; Menné, Torkil; Lidén, Carola

2011-01-01

EU legislation has reduced the epidemic of nickel contact allergy affecting the consumer, and shifted the focus towards occupational exposure. The acid wipe sampling technique was developed to quantitatively determine skin exposure to metals. To assess the clinical usefulness of the acid wipe sampling technique as part of the diagnostic investigation for occupational nickel allergy-associated hand dermatitis. Six patients with vesicular dermatitis on the hands were included. Acid wipe sampling of skin and patch testing with a nickel sulfate dilution series were performed. Nickel was detected in all samples from the hands. In all patients, the nickel content on the hands was higher than on the non-exposed control area. Occupational exposure to nickel-releasing items raised the nickel content on exposed skin as compared with a non-exposed control site. Nickel-reducing measures led to complete symptom relief in all cases. In cases of a positive nickel patch test reaction and hand eczema, patients should perform the dimethylglyoxime (DMG) test on metallic items at home and at work. The acid wipe sampling technique is useful for the diagnosis of occupational hand eczema following screening with the inexpensive DMG test. © 2010 John Wiley & Sons A/S.

Porous bimetallic PdNi catalyst with high electrocatalytic activity for ethanol electrooxidation.

Science.gov (United States)

Feng, Yue; Bin, Duan; Yan, Bo; Du, Yukou; Majima, Tetsuro; Zhou, Weiqiang

2017-05-01

Porous bimetallic PdNi catalysts were fabricated by a novel method, namely, reduction of Pd and Ni oxides prepared via calcining the complex chelate of PdNi-dimethylglyoxime (PdNi-dmg). The morphology and composition of the as-prepared PdNi were investigated by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). Furthermore, the electrochemical properties of PdNi catalysts towards ethanol electrooxidation were also studied by electrochemical impedance spectrometry (EIS), cyclic voltammetry (CV) and chronoamperometry (CA) measurement. In comparison with porous Pd and commercial Pd/C catalysts, porous structural PdNi catalysts showed higher electrocatalytic activity and durability for ethanol electrooxidation, which may be ascribed to Pd and Ni property, large electroactive surface area and high electron transfer property. The Ni exist in the catalyst in the form of the nickel hydroxides (Ni(OH) 2 and NiOOH) which have a high electron and proton conductivity enhances the catalytic activity of the catalysts. All results highlight the great potential application of the calcination-reduction method for synthesizing high active porous PdNi catalysts in direct ethanol fuel cells. Copyright © 2017 Elsevier Inc. All rights reserved.

Synthesis of carbon nanotubes by pyrolysis of solid Ni(dmg)2

International Nuclear Information System (INIS)

Kordatos, K.; Vlasopoulos, A.D.; Strikos, S.; Ntziouni, A.; Gavela, S.; Trasobares, S.; Kasselouri-Rigopoulou, V.

2009-01-01

We describe the high yield synthesis of multi-walled carbon nanotubes (MWCNTs) and the determination of the optimum production conditions. The method involves the catalytic pyrolysis of solid Ni(dmg) 2 under an Ar atmosphere. The obtained materials were characterized by scanning electron microscopy (SEM), energy dispersive X-ray (EDX) analysis, high resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD), Raman spectroscopy and thermogravimetry analysis (TGA). The data revealed the formation of MWCNTs surrounded by a varying quantity of byproducts such as amorphous carbon and metallic particles, depending mainly on the reaction temperature. Pyrolysis of Ni(dmg) 2 at 900 deg. C results in the production of nanotube material with the highest degree of crystallinity

Adsorptive Stripping Determination of Trace Nickel Using Bismuth Modified Mesoporous Carbon Composite Electrode

Science.gov (United States)

Ouyang, Ruizhuo; Feng, Kai; Su, Yongfu; Zong, Tianyu; Zhou, Xia; Lei, Tian; Jia, Pengpeng; Cao, Penghui; Zhao, Yuefeng; Guo, Ning; Chang, Haizhou; Miao, Yuqing; Zhou, Shuang

Novel bismuth nanoparticle-modified mesoporous carbon (MPC) was successfully prepared on a glassy carbon electrode (Bi@MPC/GCE) for the adsorptive stripping voltammetric determination of nickel by complexing with dimethylglyoxime (DMG). The presence of MPC obviously improved the properties of Bi particles like the electron transfer ability, particle size and hydrophicility, important parameters to achieve preferable analytical performances of Bi@MPC/GCE toward Ni(II). The best electrochemical behaviors of Bi@MPC/GCE was obtained for the stripping determination of Ni(II), compared with electrodes individually modified with Bi and MPC. The synergic effect between metallic Bi and ordered MPC (forming a 3D array like Bi microelectrodes) made major contribution to such improved electrochemical properties of Bi@MPC/GCE for Ni(II) sensing. The good linear analytical curve was achieved in a Ni(II) concentration range from 0.1μM to 5.0μM with a correlation coefficient of 0.9995. The detection limit and sensitivity were calculated to be 1.2nM (S/N=3) and 1410μAmM-1cm-2, respectively. The new method was successfully applied to Ni(II) determination in soybean samples with recoveries higher than 99% and proved to be a simple, efficient alternative for Ni(II) monitoring in real samples.

Voltammetric study of chromium(VI)-ammonia/ammonium chloride solutions in the presence of dimethylglyoxime

International Nuclear Information System (INIS)

Ginzburg, V.G.; Salikhdzhanova, R.M.F.

1987-01-01

The authors believed complexation to be possible in the system Cr(VI)-dimethylglyoxime (DMG, H 2 D) by reduction of Cr(VI) to Cr(III) on a mercury electrode. The DMG can be used in chromium voltammetry and is promising for a number of reasons: The Cr(III) has an affinity for donor nitrogen atoms in the DMG molecule. Insertion of the H 2 D into the inner sphere of the complex is expected to weaken the bond between the Cr(III) and the hydroxyl group, slow down formation of the insoluble hydroxide Cr(OH) 3 , and lower the rate of the electrode reaction Cr(III) → Cr(II). Molecules of H 2 D adsorb on a mercury electrode. It is therefore possible to accelerate the electrode process by including adsorptive preconcentration of the chromium and thus lowering its detection limit. This paper reports the voltammetric behavior of the system Cr(VI)-DMG-NH 4 + (proton donor) for the purpose of lowering the chromium detection limit

Mechanochemical synthesis and structural characterization of three novel cocrystals of dimethylglyoxime with N-heterocyclic aromatic compounds and acetamide

Science.gov (United States)

Abidi, Syed Sibte Asghar; Azim, Yasser; Gupta, Abhishek Kumar; Pradeep, Chullikkattil P.

2017-12-01

With an aim to explore the interactions of (RR'Cdbnd Nsbnd OH) oxime moiety of dimethylglyoxime (DMG) with pyridyl ring of N-heterocyclic aromatic compounds and acetamide, three novel cocrystals of dimethylglyoxime with acridine (ACR), 1,10-phenanthroline monohydrate (PT) and acetamide (ACT) are reported. These three cocrystals were obtained with a mechanochemical synthesis approach and were characterized by single crystal X-ray diffraction (SCXRD), powder X-ray diffraction (PXRD), fourier transform-infrared spectroscopy (FT-IR), differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Additionally, Hirshfeld surface analysis is used to investigate the intermolecular interaction and the crystal packing of cocrystals.

Photodegradation of Methyl Green by Nickel-Dimethylglyoxime/ZSM-5 Zeolite as a Heterogeneous Catalyst

Directory of Open Access Journals (Sweden)

Alireza Nezamzadeh-Ejhieh

2013-01-01

Full Text Available Ni-DMG/ZSM-5 zeolite was prepared by ion exchange and complexation procedures. FT-IR, XRD, SEM, TG, and DTG methods were used for characterization of the raw and modified samples. The prepared composite was used as a catalyst in the photodegradation process of an aqueous solution methyl green (MG dye under UV irradiation. The effect of key operating parameters such as catalyst dosage, temperature, the initial concentration of the dye, and pH of the samples was studied on the degradation extent of the dye. UV-Vis spectrophotometric measurements were performed for determination of the decolorization and mineralization extents. The optimal operation parameters were found as follows: , temperature of 60°C, 0.6 g L−1 of the catalyst, and 40 ppm of the dye concentration. The Ni-DMG particles out of zeolite framework did not show significant degradation efficiency. The degradation process obeys the first-order kinetic.

The optimization of the analysis of nickel-63 in urine

International Nuclear Information System (INIS)

Kramer, G.H.

1981-05-01

A method has been developed that separates nickel-63 from urine. The subsequent estimation of activity is by liquid scintillation counting. The urine is wet ashed by a new procedure which is much faster than conventional ashing methods. Interfering phosphates are removed prior to a precipitation of Ni as the dimethylglyoxime complex. The effects of the carrier weight, the pH of the phosphate removal step and the pH of the dimethylglyoxime precipiation have been investigated and optimized to give a mean recovery of 97 +- 8% for nickel-63. The detection limit is estimated to be 1.5 pCi (55 mBq) per sample. (author)

A comparative study using liquid scintillation counting to determine 63Ni in low and intermediate level radioactive waste

International Nuclear Information System (INIS)

Gautier, Celine; Colin, Christele; Garcia, Cecile

2016-01-01

A comparative study using liquid scintillation counting was performed to measure 63 Ni in low and intermediate level radioactive waste. Three dimethylglyoxime (DMG)-based radiochemical procedures (solvent extraction, precipitation, extraction chromatography) were investigated, the solvent extraction method being considered as the reference method. Theoretical speciation calculations enabled to better understand the chemical reactions involved in the three protocols and to optimize them. In comparison to the method based on DMG precipitation, the method based on extraction chromatography allowed to achieve the best results in one single step in term of recovery yield and accuracy for various samples. (author)

Fe4 cluster and a buckled macrocycle complex from the reduction of [(dmgBF2)2Fe(L)2] (L = MeCN, (t)Bu(i)NC).

Science.gov (United States)

Rose, Michael J; Winkler, Jay R; Gray, Harry B

2012-02-20

We report the syntheses, X-ray structures, and reductive electrochemistry of the Fe(II) complexes [(dmgBF(2))(2)Fe(MeCN)(2)] (1; dmg = dimethylglyoxime, MeCN = acetonitrile) and [(dmgBF(2))Fe((t)Bu(i)NC)(2)] (2; (t)Bu(i)NC = tert-butylisocyanide). The reaction of 1 with Na/Hg amalgam led to isolation and the X-ray structure of [(dmgBF(2))(2)Fe(glyIm)] (3; glyIm = glyimine), wherein the (dmgBF(2))(2) macrocyclic frame is bent to accommodate the binding of a bidentate apical ligand. We also report the X-ray structure of a rare mixed-valence Fe(4) cluster with supporting dmg-type ligands. In the structure of [(dmg(2)BF(2))(3)Fe(3)((1)/(2)dmg)(3)Fe(O)(6)] (4), the (dmgBF(2))(2) macrocycle has been cleaved, eliminating BF(2) groups. Density functional theory calculations and electron paramagnetic resonance data are in accordance with a central Fe(III) ion surrounded by three formally Fe(II)dmg(2)BF(2) units.

Technetium labeling of monoclonal antibodies with functionalized BATOs. 1. TcCl(DMG)3PITC.

Science.gov (United States)

Linder, K E; Wen, M D; Nowotnik, D P; Malley, M F; Gougoutas, J Z; Nunn, A D; Eckelman, W C

1991-01-01

BATO (boronic acid adduct of technetium dioximes) complexes, TcCl(dioxime)3BR, were prepared in which the boron substituent (R) was the protein-reactive m-phenyl isothiocyanate (PITC). The 99TcCl(dioxime)3PITC complexes [dioxime = dimethylglyoxime (DMG) or cyclohexanedione dioxime (CDO)] were prepared from 99Tc(dioxime)3(mu-OH)SnCl3 and characterized. The X-ray crystal structure of 99TcCl(DMG)3PITC was determined. The 99mTc complexes were prepared from 99mTcO4- in a process using a freeze-dried kit, either in a one-step procedure or via 99mTcCl(dioxime)3. Initial labeling studies with 99mTcCl(dioxime)3PITC were performed on glycine and polylysine and, subsequently, on mouse IgG and the B72.3 monoclonal antibody. Covalent attachment of 99mTcCl(DMG)3PITC to B72.3 was demonstrated by SDS-PAGE electrophoresis. B72.3 labeled with 99mTcCl(DMG)3PITC displayed high binding to a TAG 72 affinity column and had a distribution in normal mice similar to that reported for iodine-labeled B72.3.

Separation for the determination of 59/63Ni in radioactive wastes

International Nuclear Information System (INIS)

Lee, Chang Heon; Choi, Kwang Soon; Jee, Kwang Young; Kim, Won Ho; Jung, Kie Chul

2005-01-01

A study on the separation of 99 Tc, 94 Nb, 55 Fe, 90 Sr and 59/63 Ni in various radioactive wastes discharged from nuclear power plants has been performed for a use in their quantification which is indispensable for the evaluation of the radionuclide inventory. Ni was recovered along with Ca, Mg, Al, Cr, Ti, Mn, Ce, Na, K. and Cu through the sequential separation procedure of Re (as a surrogate of 99 Tc), Nb, Fe and Sr by anion exchange and Sr-SPec extraction chromatography. In this research, chemical separation of Ni from the co-existing elements was investigated by cation exchange and Ni-Spec extraction chromatography. Precipitation behaviour of Ni and the co-existing elements with dimethylglyoxime(DMG) was investigated in ammonium citrate/ethanol-H 2 O and tartaric acid/acetone-H 2 O in order to purify separated Ni fractions and to prepare 59/63 Ni source for the radioactivity measurement using a gas proportional counter. Recovery of Ni separated through ion exchange chromatographic separation procedure was 93.1% with relative standard deviation of 0.9%. In addition, recovery of Ni with DMG in the tartaric acid/acetone-H 2 O was 85.6% with relative standard deviation of 1.9%

Pyrolyzed Photoresist Carbon Electrodes for Trace Electroanalysis of Nickel(II

Directory of Open Access Journals (Sweden)

Ligia Maria Moretto

2015-05-01

Full Text Available Novel pyrolyzed photoresist carbon electrodes for electroanalytical applications have been produced by photolithographic technology followed by pyrolysis of the photoresist. A study of the determination of Ni(II dimethylglyoximate (Ni-DMG through adsorptive cathodic stripping voltammetry at an in situ bismuth-modified pyrolyzed photoresist electrode (Bi-PPCE is reported. The experimental conditions for the deposition of a bismuth film on the PPCE were optimized. The Bi-PPCE allowed the analysis of trace concentrations of Ni(II, even in the presence of Co(II, which is the main interference in this analysis, with cathodic stripping square wave voltammograms characterized by well-separated stripping peaks. The calculated limits of detection (LOD were 20 ng∙L−1 for Ni(II alone and 500 ng∙L−1 in the presence of Co(II. The optimized method was finally applied to the analysis of certified spring water (NIST1640a.

A molecularly imprinted electrochemiluminescence sensor based on the mimetic enzyme catalytic effect for ultra-trace Ni2+ determination.

Science.gov (United States)

Yang, Bin; Li, Jianping; Zhang, Lianming; Xu, Guobao

2016-10-21

A novel molecularly imprinted polymer (MIP) electrochemiluminescence (MIP-ECL) sensor was developed for the highly sensitive and selective determination of ultra-trace levels of Ni 2+ . The complex Ni 2+ -dimethylglyoxime (Ni-DMG) was chosen as the template molecule to construct the MIP and then acted as a mimetic enzyme to catalyse the oxidisation of luminol to enhance the ECL signal. When the imprinted cavities were occupied by Ni-DMG in the rebinding process, the ECL intensities produced by the luminol-H 2 O 2 ECL system on the MIP-modified electrode surface increased with increased concentration of the Ni-DMG complex. The highly sensitive determination of Ni 2+ was achieved through a catalytic reaction. This technique could be used for the quantitative analysis of Ni 2+ with concentrations from 3.0 × 10 -12 mol L -1 to 6.0 × 10 -9 mol L -1 . The detection limit was 1.01 × 10 -12 mol L -1 , which is much lower than that reported previously. In addition, the allowable amounts of interference ions in the MIP-ECL sensor were higher than that in other common molecularly imprinted sensors because of its excellent recognition of 3D cavity-to-complex molecules and ligand-to-metal ions. This method was successfully used to determine Ni 2+ in real samples, such as apples, carrots and grapes, and has been proven feasible for practical applications.

Controlled formation of Ni(DMG)2 microrods/tubes by manipulating the kinetics of chemical reactions and their application in naked-eye sensors.

Science.gov (United States)

Qin, Jianli; Wang, Bo; Zhang, Xiujuan; Zhang, Xiaohong

2012-08-01

We have demonstrated controlled preparation of Ni(DMG)2 microrods/tubes via chemical reaction method. By manipulating the reaction kinetics via the concentration of reactants, shapes of the resulting microstructures can be easily tuned from microrods to microtubes. Size of the resulting products can also be controlled through changing the reaction temperatures. It was proposed that under high reactants' concentrations, molecules will prefer to grow at corners or edges of nuclei with high free energies, to reduce the total energy in the system, which would lead to partial or complete hollow interiors and eventually resulted in mircotubes. The fact that DMG show high selectivity with Ni2+ and accompanied with obvious color change enable us to fabricate test strip for naked-eye detection of Ni2+. Benefit from the large surface areas of DMG nanoparticles on the test strip, the detection limit is improved by two orders over that of conventional solution method. This strategy is sensitive, simple and easy to handle, thus expected to possess potentials for the practical Ni2+ detection applications.

Highly selective micro-sequential injection lab-on-valve (muSI-LOV) method for the determination of ultra-trace concentrations of nickel in saline matrices using detection by electrothermal atomic absorption spectrometry.

Science.gov (United States)

Long, Xiangbao; Miró, Manuel; Jensen, Rikard; Hansen, Elo Harald

2006-10-01

A highly selective procedure is proposed for the determination of ultra-trace level concentrations of nickel in saline aqueous matrices exploiting a micro-sequential injection Lab-On-Valve (muSI-LOV) sample pretreatment protocol comprising bead injection separation/pre-concentration and detection by electrothermal atomic absorption spectrometry (ETAAS). Based on the dimethylglyoxime (DMG) reaction used for nickel analysis, the sample, as contained in a pH 9.0 buffer, is, after on-line merging with the chelating reagent, transported to a reaction coil attached to one of the external ports of the LOV to assure sufficient reaction time for the formation of Ni(DMG)(2) chelate. The non-ionic coordination compound is then collected in a renewable micro-column packed with a reversed-phase copolymeric sorbent [namely, poly(divinylbenzene-co-N-vinylpyrrolidone)] containing a balanced ratio of hydrophilic and lipophilic monomers. Following elution by a 50-muL methanol plug in an air-segmented modality, the nickel is finally quantified by ETAAS. Under the optimized conditions and for a sample volume of 1.8 mL, a retention efficiency of 70 % and an enrichment factor of 25 were obtained. The proposed methodology showed a high tolerance to the commonly encountered alkaline earth matrix elements in environmental waters, that is, calcium and magnesium, and was successfully applied for the determination of nickel in an NIST standard reference material (NIST 1640-Trace elements in natural water), household tap water of high hardness and local seawater. Satisfying recoveries were achieved for all spiked environmental water samples with maximum deviations of 6 %. The experimental results for the standard reference material were not statistically different to the certified value at a significance level of 0.05.

Epicutaneous exposure to nickel induces nickel allergy in mice via a MyD88-dependent and interleukin-1-dependent pathway

DEFF Research Database (Denmark)

Vennegaard, Marie T; Dyring-Andersen, Beatrice; Skov, Lone

2014-01-01

-lasting epicutaneous exposure to nickel. OBJECTIVE: To develop a mouse model reflecting nickel allergy in humans induced by epicutaneous exposure to nickel, and to investigate the mechanisms involved in such allergic responses. METHODS: Mice were exposed to NiCl2 on the dorsal side of the ears. Inflammation...... was evaluated by the swelling and cell infiltration of the ears. T cell responses were determined as numbers of CD4(+) and CD8(+) T cells in the draining lymph nodes. Localization of nickel was examined by dimethylglyoxime staining. RESULTS: Epicutaneous exposure to nickel results in prolonged localization...... of nickel in the epidermis, and induces nickel allergy in mice. The allergic response to nickel following epicutaneous exposure is MyD88-dependent and interleukin (IL)-1 receptor-dependent, but independent of toll-like receptor (TLR)-4. CONCLUSION: This new model for nickel allergy that reflects...

ELECTROREDUCTION MECHANISM OF Ni(DMG)-2 COMPLEX STUDIED WITH QUANTUM CHEMICAL METHOD

Institute of Scientific and Technical Information of China (English)

倪亚明; 任镜清; 黎健; 王德民; 梁伟根; 朱芝仙; 高小霞

1990-01-01

The electronic structures of the species Ni（DMG）2, （Ni（DMG）2）- and （Ni（DMG）2）2- have been studied by INDO quantum chemical method. The results have clearly shown that in the first stage of the electroreduction of Ni（DMG）2, one electron interacts with the d orbitals on the nickel atom, while in the further stage the second electron interacts with the p orbitals on the nitrogen atoms. It conforms with our electrochemical experimental studies which showed that not only Ni（Ⅱ） is reduced but also DMG is catalytically reduced during the reduction of Ni（DMG）2.

Labelling of 4-dihydroxyborylphenylalanine(BPA) with 99Tcm and biodistribution of 99Tcm-DMG-BPA

International Nuclear Information System (INIS)

Xiao Yan; Tu Jing; Tang Xiuhuan; Tang Lingtian; Wang Xiangyun

2005-01-01

BPA(4-dihydroxyborylphenylalanine) has being used in clinical trials for treatment of cancer with boron neutron capture therapy (BNCT) technology for its selective accumulation in tumors. BPA is prepared according to the published synthetic procedure. A new BATO complex is synthesized with dimethylglyoxime, BPA, and 99 Tc m O 4 - as the starting materials via a template reaction. The biodistribution of 99 Tc m -DMG-BPA is studied. The results demonstrate that the complex is selectively accumulated in tumor and slowly cleared from it, the uptake in tumor is higher than in blood, heart, muscle and most of the other organs. The uptake ratio of tumor-to-tissue increased along with time. At 4 hour after injection, the uptake ratio of tumor to muscle reached 6.0, tumor/blood 4.5, tumor/heart 6.0, tumor/lung 3.0, tumor/liver 0.41, and tumor/kidney 0.134. The possible molecular structure of 99 Tc m -DMG-BPA complex is predicated by ab inito MO calculation. (authors)

SQUARE WAVE CATHODIC STRIPPING VOLTAMMETRY ADSORPTIVE FOR NICKEL AND COBALT ANALYSIS

Directory of Open Access Journals (Sweden)

Saryati Saryati

2010-06-01

Full Text Available The adsorptive stripping voltammetric determination of Ni and Co based on adsorption of the Ni/Co and dimethylglioxime (DMG complex on a hanging mercury drop electrode is studied. The reduction current of the adsorbed DMG complex is measured by square wave cathodic stripping voltammetry method. The effect of various parameters such as ligand concentration, pH of supporting electrolytic, adsorption potential and adsorption time on the current peak of Ni and Co voltammogram were studied. Optimum condition of this method are supporting electrolyte pH 9, DMG concentration 5×10 -4 M, adsorption potential -0.7 V vs Ag/AgCl and adsorption time 180 second. A linier relationship between the current peak and Ni or Co concentration was obtained in the range 5 - 30 ng/mL and the detection limit 0.6 ng/ml for both Ni and Co. The recovery of Ni and Co were 98.11-104.17% using standard biological materials with RSD 2.59 - 10.37%. Based on ";t"; test can be conclude that the result are nearly equal to the standard reference material.   Keywords: adsorptive stripping voltammetric, dimethylglioxime complex, nickel, cobalt

Synergistic effect of novel redox additives of p-nitroaniline and dimethylglyoxime for highly improving the supercapacitor performances.

Science.gov (United States)

Nie, Yong Fu; Wang, Qian; Chen, Xiang Ying; Zhang, Zhong Jie

2016-01-28

In present work, we demonstrate a simple but effective strategy for high-performance supercapacitors by adding the p-nitroaniline (PNA) into an alkaline electrolyte of KOH. PNA possesses a unique molecular structure with the functional groups of -NH2 and -NO2. Besides, both the product of nitro-reduction (-NH2) and intrinsic -NH2 on the benzene ring can lead to the occurrence of Faradaic redox reactions accompanied by the electron/proton transfer in the mixed electrolytes, whose pseudocapacitance can greatly enhance the total capacitance. Furthermore, another effective additive of the dimethylglyoxime (DMG) has been incorporated into carbon materials for further improving the performances of supercapacitors with a PNA + KOH electrolyte. As for the DMG + PNA + KOH system, a galvanostatic capacitance up to 386.1 F g(-1) of the DMG-0.15-PNA-0.15 sample at 3 A g(-1), which is nearly two times higher than that of the PNA-0.15 sample (183.6 F g(-1)) in the PNA + KOH system and nearly three-fold capacitance of the carbon-blank (132.3 F g(-1)) in the KOH system at the same current density. Furthermore, the specific capacitance still can reach up to 260.0 F g(-1) even at 40 A g(-1) with a 67.4% capacitance retention ratio. Besides, the DMG-0.15-PNA-0.15 sample exhibits an exceptional capacitance retention of 113% after 5000 charge/discharge cycles by virtue of the potential activated process, which clearly reveals the excellent cycling stability. These remarkable enhancements are ascribed to the synergistic effects of novel additives of PNA and DMG.

Direct quantification of nickel in stainless steels by spectrophotometry

International Nuclear Information System (INIS)

Singh, Ritu; Raut, Vaibhavi V.; Jeyakumar, S.; Ramakumar, K.L.

2007-01-01

A spectrophotometric method based on the Ni-DMG complex for the quantification of nickel in steel samples without employing any prior separation is reported in the present study. The interfering ions are masked by suitable complexing agents and the method was extended to real samples after validating with BCS and Euro steel standards. (author)

Determination of palladium in various samples by atomic absorption spectrometry after preconcentration with dimethylglyoxime on silica gel

International Nuclear Information System (INIS)

Tokalioglu, Serife; Oymak, Tuelay; Kartal, Senol

2004-01-01

A preconcentration method based on the adsorption of palladium-dimethylglyoxime (DMG) complex on silica gel for the determination of palladium at trace levels by atomic absorption spectrometry (AAS) has been developed. The retained palladium as Pd(DMG) 2 complex was eluted with 1 mol l -1 HCl in acetone. The effect of some analytical parameters such as pH, amount of reagent and the sample volume on the recovery of palladium was examined in synthetic solutions containing street dust matrix. The influence of some matrix ions on the recovery of palladium was investigated by using the developed method when the elements were present both individually and together. The results showed that 2500 μg ml -1 Na + , K + , Mg 2+ , Al 3+ and Fe 3+ ; 5000 μg ml -1 Ca 2+ ; 500 μg ml -1 Pb 2+ ; 125 μg ml -1 Zn 2+ ; 50 μg ml -1 Cu 2+ and 25 μg ml -1 Ni 2+ did not interfere with the palladium signal. At the optimum conditions determined experimentally, the recovery for palladium was found to be 95.3±1.2% at the 95% confidence level. The relative standard deviation and limit of detection (3s/b) of the method were found to be 1.7% and 1.2 μg l -1 , respectively. In order to determine the adsorption behaviour of silica gel, the adsorption isotherm of palladium was studied and the binding equilibrium constant and adsorption capacity were calculated to be 0.38 l mg -1 and 4.06 mg g -1 , respectively. The determination of palladium in various samples was performed by using both flame AAS and graphite furnace AAS. The proposed method was successfully applied for the determination of palladium in the street dust, anode slime, rock and catalytic converter samples

Preparation of fine Ni powders from nickel hydrazine complex

International Nuclear Information System (INIS)

Park, Jung Woo; Chae, Eun H.; Kim, Sang H.; Lee, Jong Ho; Kim, Jeong Wook; Yoon, Seon Mi; Choi, Jae-Young

2006-01-01

Fine nickel powders with narrow size distribution have been prepared from the reduction of nickel hydrazine complexes in aqueous solution. The pure nickel hydrazine complexes, [Ni(N 2 H 4 ) 3 ]Cl 2 were prepared with the molar ratio of N 2 H 4 /Ni 2+ = 4.5, while a mixture of complexes, such as Ni(N 2 H 4 ) 2 Cl 2 , [Ni(N 2 H 4 ) 3 ]Cl 2 , and [Ni(NH 3 ) 6 ]Cl 2 were formed with N 2 H 4 /Ni 2+ 2+ to metallic Ni powder proceeded via the formation of nickel hydroxide which was reduced by hydrazine liberated from the ligand exchange reaction between the nickel hydrazine complex and NaOH. The standard deviation of the particle size decreased with the decreasing molar concentration of nickel hydrazine complex while the mean particle size increased. As the amount of hydrazine increased, the surface roughness of the particles was improved significantly due to the catalytic decomposition of the excess hydrazine at the surface of the nickel particle. It was found that average particle size could be controlled from 150 to 380 nm by adjusting the reaction molar ratio and temperature

Epicutaneous exposure to nickel induces nickel allergy in mice via a MyD88-dependent and interleukin-1-dependent pathway.

Science.gov (United States)

Vennegaard, Marie T; Dyring-Andersen, Beatrice; Skov, Lone; Nielsen, Morten M; Schmidt, Jonas D; Bzorek, Michael; Poulsen, Steen S; Thomsen, Allan R; Woetmann, Anders; Thyssen, Jacob P; Johansen, Jeanne D; Odum, Niels; Menné, Torkil; Geisler, Carsten; Bonefeld, Charlotte M

2014-10-01

Several attempts to establish a model in mice that reflects nickel allergy in humans have been made. Most models use intradermal injection of nickel in combination with adjuvant to induce nickel allergy. However, such models poorly reflect induction of nickel allergy following long-lasting epicutaneous exposure to nickel. To develop a mouse model reflecting nickel allergy in humans induced by epicutaneous exposure to nickel, and to investigate the mechanisms involved in such allergic responses. Mice were exposed to NiCl2 on the dorsal side of the ears. Inflammation was evaluated by the swelling and cell infiltration of the ears. T cell responses were determined as numbers of CD4+ and CD8+ T cells in the draining lymph nodes. Localization of nickel was examined by dimethylglyoxime staining. Epicutaneous exposure to nickel results in prolonged localization of nickel in the epidermis, and induces nickel allergy in mice. The allergic response to nickel following epicutaneous exposure is MyD88-dependent and interleukin (IL)-1 receptor-dependent, but independent of toll-like receptor (TLR)-4. This new model for nickel allergy that reflects epicutaneous exposure to nickel in humans shows that nickel allergy is dependent on MyD88 and IL-1 receptor signalling, but independent of TLR4. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Effect of Ni +-ION bombardment on nickel and binary nickel alloys

Science.gov (United States)

Roarty, K. B.; Sprague, J. A.; Johnson, R. A.; Smidt, F. A.

1981-03-01

Pure nickel and four binary nickel alloys have been subjected to high energy Ni ion bombardment at 675, 625 and 525°C. After irradiation, each specimen was studied by transmission electron microscopy. The pure nickel control was found to swell appreciably (1 to 5%) and the Ni-Al and the Ni-Ti samples were found to swell at all temperatures, but to a lesser degree (0.01 to 0.35%). The Ni-Mo contained a significant density of voids only at 525° C, while swelling was suppressed at all temperatures in the Ni-Si alloy. The dislocation structure progressed from loops to tangles as temperature increased in all materials except the Ni-Ti, in which there was an absence of loops at all temperatures. Dislocation densities decreased as temperature increased in all samples. These results do not correlate well with the relative behavior of the same alloys observed after neutron irradiation at 455°C. The differences between these two sets of data appear to be caused by different mechanisms controlling void nucleation in ion and neutron irradiation of these alloys.

In vitro activity of DMG-Mino and DMG-DM Dot, two new glycylcyclines, against anaerobic bacteria.

Science.gov (United States)

Nord, C E; Lindmark, A; Persson, I

1993-10-01

The in vitro activity of DMG-Mino and DMG-DM Dot against 350 anaerobic bacterial strains including anaerobic cocci, Propionibacterium acnes, Clostridium perfringens, Clostridium difficile, Bacteroides fragilis, other Bacteroides species and fusobacteria was determined by the agar dilution method. Their activity was compared with that of minocycline, doxycycline, piperacillin, cefoxitin, imipenem, clindamycin and metronidazole. DMG-Mino and DMG-DM Dot and imipenem were the most active agents tested. DMG-Mino and DMG-DM Dot had in vitro activity superior to that of minocycline and doxycycline.

Microplasma synthesis on aluminum with additions of iron and nickel soluble complexes in electrolyte

Energy Technology Data Exchange (ETDEWEB)

Rogov, A.B., E-mail: alex-lab@bk.ru [Nikolaev Institute of Inorganic Chemistry. 3, Acad. Lavrentiev Ave, Novosibirsk, 630090 (Russian Federation); Mironov, I.V.; Terleeva, O.P.; Slonova, A.I. [Nikolaev Institute of Inorganic Chemistry. 3, Acad. Lavrentiev Ave, Novosibirsk, 630090 (Russian Federation)

2012-10-01

Highlights: Black-Right-Pointing-Pointer Alkaline homogeneous electrolyte with transition metals complexes. Black-Right-Pointing-Pointer Coatings contain metallic iron, nickel and their oxides in alumina-silica matrix. Black-Right-Pointing-Pointer Effect of Fe/Ni ratio on coatings properties and process characteristics. - Abstract: The microplasma synthesis of coatings containing iron and nickel from homogeneous electrolytes has been studied. For stabilization of transition metals in solution, it is proposed to use chelation. It was found that the synthesis of coatings using alternating current leads to the formation of metallic iron and nickel particles in addition to oxide phases. The iron and nickel complexes concentrations ratio in the electrolyte correlates with the coatings composition. Obtained coatings have been studied by scanning electron microscopy with X-ray microanalyser and by X-ray diffraction with Cu and Mo radiation. The metal content in the coating was determined spectrophotometrically from the absorption of iron thiocyanate complexes and nickel dimethylglyoxime complex.

Quantitative analysis of nickel in zirconium and zircaloy; Dosage du nickel dans le zirconium et dans le zircaloy

Energy Technology Data Exchange (ETDEWEB)

Rastoix, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1957-07-01

A rapid spectrophotometric has been developed for determination of 10 to 1000 ppm of Ni in zirconium and zircaloy using dimethylglyoxime. Iron, copper, tin and chromium, do not interfere at the concentration usually present in zirconium and its alloys. (author) [French] On determine colorimetriquenent 10 a 1000 ppm de Ni dans le zirconium et le zircaloy par photo colorimetrie a 440 m{mu} de la dimethylglyoxime nickelique. Le dosage est rapide. Le fer, le cuivre, l'etain, le chrome ne genent pas aux concentrations habituellement rencontrees dans le zirconium et ses alliages. (auteur)

Nickel Nanowire@Porous NiCo2O4 Nanorods Arrays Grown on Nickel Foam as Efficient Pseudocapacitor Electrode

Directory of Open Access Journals (Sweden)

Houzhao Wan

2017-12-01

Full Text Available A three dimensional hierarchical nanostructure composed of nickel nanowires and porous NiCo2O4 nanorods arrays on the surface of nickel foam is successfully fabricated by a facile route. In this structure, the nickel nanowires are used as core materials to support high-pseudocapacitance NiCo2O4 nanorods and construct the well-defined NiCo2O4 nanorods shell/nickel nanowires core hierarchical structure on nickel foam. Benefiting from the participation of nickel nanowires, the nickel nanowire@NiCo2O4/Ni foam electrode shows a high areal specific capacitance (7.4 F cm−2 at 5 mA cm−2, excellent rate capability (88.04% retained at 100 mA cm−2, and good cycling stability (74.08% retained after 1,500 cycles. The superior electrochemical properties made it promising as electrode for supercapacitors.

Synthesis and Characterization of Mixed Iron-Manganese Oxide Nanoparticles and Their Application for Efficient Nickel Ion Removal from Aqueous Samples

Science.gov (United States)

Serra, Antonio; Monteduro, Anna Grazia; Padmanabhan, Sanosh Kunjalukkal; Licciulli, Antonio; Bonfrate, Valentina; Salvatore, Luca; Calcagnile, Lucio

2017-01-01

Mixed iron-manganese oxide nanoparticles, synthesized by a simple procedure, were used to remove nickel ion from aqueous solutions. Nanostructures, prepared by using different weight percents of manganese, were characterized by transmission electron microscopy, selected area diffraction, X-ray diffraction, Raman spectroscopy, and vibrating sample magnetometry. Adsorption/desorption isotherm curves demonstrated that manganese inclusions enhance the specific surface area three times and the pores volume ten times. This feature was crucial to decontaminate both aqueous samples and food extracts from nickel ion. Efficient removal of Ni2+ was highlighted by the well-known dimethylglyoxime test and by ICP-MS analysis and the possibility of regenerating the nanostructure was obtained by a washing treatment in disodium ethylenediaminetetraacetate solution. PMID:28804670

Nickel release from earrings purchased in the united states: the San Francisco earring study

DEFF Research Database (Denmark)

Maibach, H.I.; Thyssen, Jacob Pontoppidan

2008-01-01

Background: Nickel sensitization is frequent among US patients with dermatitis and in the general population. In Europe, decreasing prevalences of nickel sensitization are observed as a result of the European Union Nickel Directive. However, no directive exists in the United States. Objectives: We...... sought to examine nickel release from inexpensive earrings and discuss possible methods of reducing nickel exposure among consumers. Methods: A total of 34 different stores and artists were visited. A total of 277 earrings were purchased and examined with the dimethylglyoxitne (DMG) test. Results: DMG......-positive earrings were identified from local artists (69%) and tourist stores (42.9%) but also chain stores targeting young (24.1%) and mature (1.7%) women. No correlation between price and outcome of DMG testing was identified. Limitations. Our study does not reflect buying trends in the United States...

Nickel Nanowire@Porous NiCo{sub 2}O{sub 4} Nanorods Arrays Grown on Nickel Foam as Efficient Pseudocapacitor Electrode

Energy Technology Data Exchange (ETDEWEB)

Wan, Houzhao; Li, Lang; Zhang, Jun; Liu, Xiang; Wang, Hanbin; Wang, Hao, E-mail: nanoguy@126.com [Faculty of Physics and Electronic Science, Hubei Collaborative Innovation Center for Advanced Organic Chemical Materials, Hubei Key Laboratory of Ferro & Piezoelectric Materials and Devices, Hubei University, Wuhan (China)

2017-12-13

A three dimensional hierarchical nanostructure composed of nickel nanowires and porous NiCo{sub 2}O{sub 4} nanorods arrays on the surface of nickel foam is successfully fabricated by a facile route. In this structure, the nickel nanowires are used as core materials to support high-pseudocapacitance NiCo{sub 2}O{sub 4} nanorods and construct the well-defined NiCo{sub 2}O{sub 4} nanorods shell/nickel nanowires core hierarchical structure on nickel foam. Benefiting from the participation of nickel nanowires, the nickel nanowire@NiCo{sub 2}O{sub 4}/Ni foam electrode shows a high areal specific capacitance (7.4 F cm{sup −2} at 5 mA cm{sup −2}), excellent rate capability (88.04% retained at 100 mA cm{sup −2}), and good cycling stability (74.08% retained after 1,500 cycles). The superior electrochemical properties made it promising as electrode for supercapacitors.

Determination of nickel-63

International Nuclear Information System (INIS)

Poletiko, C.

1988-01-01

The research of activation products in the environment is often centered on cobalt-60 or other gamma emitters, since pure beta emitters require time consuming separations to be counted. However, some beta emitters must be checked because they have a build up in the environment, leading to potential hazards. Among these nuclides, there is nickel-63 which is a pure, soft beta emitter (67 keV) with a long half-life (100 years). A chemical separation, providing good results, was developed. Such a separation is based upon nickel carrier addition in the sample than DMG complex formation and isolation; after elimination of solvent. DMG complex is destroyed. Chemical yield is determined by flame atomic absorption measurement and nickel-63 counted by liquid scintillation. The described procedure allows the determination of low-level activities in different samples (soils, effluents, etc.). Detection limits are close to 0.1 Bq per sample

SUPPLEMENTARY INFORMATION Dimethylglyoxime as an ...

Indian Academy of Sciences (India)

lenovo

1. SUPPLEMENTARY INFORMATION. Dimethylglyoxime as an Efficient Ligand for Copper-Catalyzed Hydroxylation of Aryl. Halides. SURESH S SHENDAGE*. Department of Chemistry, KET'S Vinayak Ganesh Vaze College of Arts, Science and. Commerce, Mithagar Road, Mulund (E) Mumbai, Maharashtra 400 081, India.

Synthesis and Characterization of Mixed Iron-Manganese Oxide Nanoparticles and Their Application for Efficient Nickel Ion Removal from Aqueous Samples

Directory of Open Access Journals (Sweden)

Alessandro Buccolieri

2017-01-01

Full Text Available Mixed iron-manganese oxide nanoparticles, synthesized by a simple procedure, were used to remove nickel ion from aqueous solutions. Nanostructures, prepared by using different weight percents of manganese, were characterized by transmission electron microscopy, selected area diffraction, X-ray diffraction, Raman spectroscopy, and vibrating sample magnetometry. Adsorption/desorption isotherm curves demonstrated that manganese inclusions enhance the specific surface area three times and the pores volume ten times. This feature was crucial to decontaminate both aqueous samples and food extracts from nickel ion. Efficient removal of Ni2+ was highlighted by the well-known dimethylglyoxime test and by ICP-MS analysis and the possibility of regenerating the nanostructure was obtained by a washing treatment in disodium ethylenediaminetetraacetate solution.

Belt Buckles-Increasing Awareness of Nickel Exposure in Children: A Case Report.

Science.gov (United States)

Goldenberg, Alina; Admani, Shehla; Pelletier, Janice L; Jacob, Sharon E

2015-09-01

Children, especially those with atopic dermatitis, are at risk for nickel sensitization and subsequent dermatitis from metal-containing objects, namely belt buckles. We describe allergic contact dermatitis in 12 children with peri-umbilical nickel dermatitis (with and without generalized involvement) caused by dimethylglyoxime-positive belt buckles. The patients' symptoms resolved with avoidance of the nickel-containing products. Copyright © 2015 by the American Academy of Pediatrics.

Comparative Studies of the Speciation Patterns of Nickel and ...

African Journals Online (AJOL)

Results of speciation stdies of nickel and chromium in wastewater, surface and groundwater systems using flame atomic absorption spectrometry (FAAS), graphite furnace atomic absorption spectrometry (GFAAS) and differential pulse adsorptive cathodic stripping voltammetry (DPAdCSV) are presented. Dimethylglyoxime ...

Activation behaviour of ZrCrNi mechanically milled with nickel

International Nuclear Information System (INIS)

Jung, C. B.; Ho Kim, J.; Sub Lee, K.

1998-01-01

AB 2 type Laves phase alloys have some promising properties as a negative electrode in rechargeable Ni/MH batteries because of high electrochemical capacity and good cyclic life. However, they have the disadvantage of requiring many charge-discharge cycles for activation. In this study, the mechanical milling with nickel has been introduced to modify the electrochemical behaviour of the ZrCrNi alloy. A composite-like structure (ZrCrNi+nickel) and nanocrystalline ZrCrNi were obtained through the mechanical milling and the hydrogenation behaviour of the electrode was greatly improved. (orig.)

Heavy metal environmental impact. Nickel (Ni); Impatto ambientale da metalli pesanti. Il Nichel (Ni)

Energy Technology Data Exchange (ETDEWEB)

Bressa, G. [Padua Univ. Padua (Italy). Dipt. di Farmacologia, Lab. di Tossicologia

2001-02-01

Nickel (Ni) is a heavy metal in over 3.000 different alloys used to produce kitchen utensils, batteries, coins, etc.. Human extractive and industrial activities are therefore a cause for environmental dispersion of this metal into the biosphere. This shows how in urban areas car traffic and house-heating are the main sources of nickel pollution. Nickel is relatively non-toxic, such as iron, cobalt, copper and zinc; nevertheless prolonged inhalation of dust containing such compounds as Ni O or NiCl{sub 2} concurs in the outbreak of respiratory pathologies. The carcinogenic effect of such compounds as Ni S, Ni O and Ni(CO){sub 4} has been confirmed by experiments on laboratory animals. Ni potentially toxic concentrations, and as a consequence of potential environmental impact, are to be mainly found in populated areas where the main sources are represented by industries and landfills. [Italian] Il nichel (Ni) e' un metallo presente in oltre 3.000 differenti leghe che vengono utilizzate per la produzione di utensili da cucina, batterie, monete, ecc.. Le attivita' estrattive ed industriali dell'uomo sono quindi causa di una dispersione del metallo nella biosfera. Sono stati riscontrati elevati tassi di Ni nell'atmosfera di aree urbane. Cio' sta a dimostrare che nelle aree urbane il traffico automobilistico e il riscaldamento domestico sono le fonti principali di inquinamento da tale metallo. Il nichel e' relativamente atossico, analogamente a ferro, cobalto, rame e zinco, tuttavia l'inalazione protratta di polveri contenenti composti come il NiO o il NiCl{sub 2} contribuisce al manifestarsi di patologie dell'apparato respiratorio. E' stato confermato sperimentalmente su animali da laboratorio l'effetto cancerogeno di alcuni composti quali NiS, NiO e Ni(CO){sub 4}. Concentrazioni potenzialmente tossiche di Ni, e quindi di probabile impatto ambientale, sono maggiormente da ricercare nelle zone antropizzate dove le fonti

Validation of a method for the determination of 14C and 63Ni in samples of concrete

International Nuclear Information System (INIS)

Rosskopfova, Olga; Galambos, Michal; Pupak, Matus

2009-01-01

For the determination of 14 C, the concrete sample was distilled in inert atmosphere and the released 14 CO 2 was trapped in a scintillation vial with Carbo-Sorb E. Permafluor E was added and the well mixed sample was kept in the dark for 24 h, after which the preparation was measured on a liquid scintillation spectrometer. For the determination of 63 Ni the sample was ignited at 550 deg C overnight and subjected to acid leaching. Nickel was then separated by a procedure which included separation from Fe by precipitation with NH 4 OH and precipitation of Ni with dimethylglyoxime and purification by extraction chromatography on Ni Resin; 63 Ni was determined by liquid scintillation spectrophotometry of the beta radiation. The participation in the interlaboratory comparison exercise gave evidence of the reliability and quality of the results achieved by the laboratory. (P.A.)

Preparation and Spectral Properties of Mixed-Ligand Complexes of VO(IV, Ni(II, Zn(II, Pd(II, Cd(II and Pb(II with Dimethylglyoxime and N-acetylglycine

Directory of Open Access Journals (Sweden)

Shayma A. Shaker

2010-01-01

Full Text Available A number of mixed-ligand complexes of the general formula [M(D(G] where D=dimethylglyoximato monoanion, G=N-acetylglycinato and M=VO(IV, Ni(II, Zn(II, Pd(II, Cd(II and Pb(II were prepared. Each complex was characterized by elemental analysis, determination of metal, infrared spectra, electronic spectra, (1H and 13C NMR spectra, conductivity and magnetic moments. All these complexes were not soluble in some of the organic solvent but highly soluble in dimethylformamide. The conductivity data showed the non-electrolytic nature of the complexes. The electronic spectra exhibited absorption bands in the visible region caused by the d-d electronic transition such as VO(IV, Ni(II and Pd(II. The IR and (1H, 13C NMR spectra which have indicate that the dimethylglyoxime was coordinated with the metal ions through the N and O atoms of the oxime group and N-acetylglycine was coordinated with metal ions through the N atom and terminal carboxyl oxygen atom.

Nickel and Cobalt Release From Children's Toys Purchased in Denmark and the United States

DEFF Research Database (Denmark)

Jensen, P.; Hamann, Dathan; Hamann, Carsten R.

2014-01-01

from children's toys. Methods : We purchased 212 toys in 18 different retail and online stores in the United States and Denmark. Nickel and cobalt release was tested using the dimethylglyoxime and cobalt screening spot tests. Results : A total of 73 toys (34.4%) released nickel, and none released......Background : Nickel is the most common allergen detected by patch testing in children. There is an increasing number of cases in children who have not had exposure to piercing. Although the clinical relevance of nickel patch test reactions in children is sometimes uncertain, continued vigilance...

Quantitative analysis of nickel in zirconium and zircaloy

International Nuclear Information System (INIS)

Rastoix, M.

1957-01-01

A rapid spectrophotometric has been developed for determination of 10 to 1000 ppm of Ni in zirconium and zircaloy using dimethylglyoxime. Iron, copper, tin and chromium, do not interfere at the concentration usually present in zirconium and its alloys. (author) [fr

DMG MORI阵容强大参展CIMES 2014

Institute of Scientific and Technical Information of China (English)

无

2014-01-01

集MORI SEIKI 65年和DMG 143年的优势．DMG MORI整合了来自德国与日本机床制造的传统、精密和领先技术。作为行业创新引领者,DMG MORI将继续开发引领趋势的产品,

Shear Stress in Nickel and Ni-60Co under One-Dimensional Shock Loading

International Nuclear Information System (INIS)

Workman, A.; Wallwork, A.; Meziere, Y. J. E.; Millett, J. C. F.; Bourne, N. K.

2006-01-01

The dynamic response of pure nickel (Ni), and its alloy, Ni-60Co (by weight %), has been investigated during one-dimensional shock loading. Few materials' properties are different and the only significantly altered feature is the reduced stacking fault energy (SFE) for the Ni-60Co. This paper considers the effect of this reduced SFE on the shear strength. Data (in terms of shock stress, particle velocity and shock velocity) are also presented. The influence on the shear stress, τ of cobalt additions in nickel are then investigated and presented. Results indicate that the lateral stress is increasing in both materials with the increasing impact stress. The shear stress was found to be higher in the nickel than in the Ni-60Co. The progressive decrease of the lateral stress noted during loading indicates a complex mechanism of deformation behind the shock front

Fabrication of Nickel Nanosized Powder from LiNiO2 from Spent Lithium-Ion Battery

Directory of Open Access Journals (Sweden)

Shun-Myung Shin

2018-01-01

Full Text Available In this study, a fabrication of nickel nanoparticles from LNO(LiNiO2, which is a cathode active material, was synthesized by the liquid reduction process of NiSO4, obtained through a leaching and purification process. Hydrazine monohydrate (N2H4·H2O was used as a liquid reducing agent and it was added to NiSO4 at a volume ratio of NiSO4:N2H4·H2O = 10:3 and reacted for 10 min to synthesize the nickel hydrazine complex. Sodium hydroxide was added to the nickel hydrazine complex at the weight ratio of NiSO4:NaOH = 10:1.25–1.5 and the reduction reaction was performed at 80 °C for 15 min to synthesize nickel particles. Synthesized nickel particles were agglomerated and had a mean size of 200 nm to 300 nm. Ultrasonic dispersion, which is a physical dispersion method, was conducted. The nickel had particles of 100 nm or less when dispersed for 2 h at an ultrasonic intensity of 40 kHz. In order to prevent the agglomeration of the dispersed particles again, polyvinylpyrrolidone (PVP, an interfacial stabilizer, was added to stabilize the dispersed particles. It was confirmed that the nanoparticles were stably retained when PVP was added in an amount of 1 to 2 wt % based on the weight of the nickel. The purity of nickel recovered was found to be 99.62 wt %.

Auto Catalog of DMG

Institute of Scientific and Technical Information of China (English)

1995-01-01

<正> The description given below will cover all the complete vehicles produced by the DMG during the "Eighth-Five-Year- Plan", which will surely help you with fully understanding the motor vehicle composition.

Nickel Oxide (NiO nanoparticles prepared by solid-state thermal decomposition of Nickel (II schiff base precursor

Directory of Open Access Journals (Sweden)

Aliakbar Dehno Khalaji

2015-06-01

Full Text Available In this paper, plate-like NiO nanoparticles were prepared by one-pot solid-state thermal decomposition of nickel (II Schiff base complex as new precursor. First, the nickel (II Schiff base precursor was prepared by solid-state grinding using nickel (II nitrate hexahydrate, Ni(NO32∙6H2O, and the Schiff base ligand N,N′-bis-(salicylidene benzene-1,4-diamine for 30 min without using any solvent, catalyst, template or surfactant. It was characterized by Fourier Transform Infrared spectroscopy (FT-IR and elemental analysis (CHN. The resultant solid was subsequently annealed in the electrical furnace at 450 °C for 3 h in air atmosphere. Nanoparticles of NiO were produced and characterized by X-ray powder diffraction (XRD at 2θ degree 0-140°, FT-IR spectroscopy, scanning electron microscopy (SEM and transmission electron microscopy (TEM. The XRD and FT-IR results showed that the product is pure and has good crystallinity with cubic structure because no characteristic peaks of impurity were observed, while the SEM and TEM results showed that the obtained product is tiny, aggregated with plate-like shape, narrow size distribution with an average size between 10-40 nm. Results show that the solid state thermal decomposition method is simple, environmentally friendly, safe and suitable for preparation of NiO nanoparticles. This method can also be used to synthesize nanoparticles of other metal oxides.

Effects of P/Ni ratio and Ni content on performance of γ-Al_2O_3-supported nickel phosphides for deoxygenation of methyl laurate to hydrocarbons

International Nuclear Information System (INIS)

Zhang, Zhena; Tang, Mingxiao; Chen, Jixiang

2016-01-01

Graphical abstract: - Highlights: • The formation of AlPO_4 was unfavorable for that of nickel phosphides. • The phase compositions of nickel phosphide depended on the amount of reduced P. • Catalytic activity was determined by surface Ni site density and catalyst acidity. • HDO pathway was promoted by increasing P/Ni ratio and Ni content. • Nickel phosphide gave much higher carbon yield and lower H_2 consumption than Ni. - Abstract: γ-Al_2O_3-supported nickel phosphides (mNi-Pn) were prepared by the TPR method and tested for the deoxygenation of methyl laurate to hydrocarbons. The effects of the P/Ni ratio (n = 1.0–2.5) and Ni content (m = 5–15 wt.%) in the precursors on their structure and performance were investigated. Ni/γ-Al_2O_3 was also studied for comparison. It was found that the formation of AlPO_4 in the precursor inhibited the reduction of phosphate and so the formation of nickel phosphides. With increasing the P/Ni ratio and Ni content, the Ni, Ni_3P, Ni_1_2P_5 and Ni_2P phases orderly formed, accompanying with the increases of their particle size and the amount of weak acid sites (mainly due to P-OH group), while the CO uptake and the amount of medium strong acid sites (mainly related to Ni sites) reached maximum on 10%Ni-P1.5. In the deoxygenation reaction, compared with Ni/γ-Al_2O_3, the mNi-Pn catalysts showed much lower activities for decarbonylation, C−C hydrogenolysis and methanation due to the ligand and ensemble effects of P. The conversion and the selectivity to n-C11 and n-C12 hydrocarbons achieved maximum on 10%Ni-P 2.0 for the 10%Ni-Pn catalysts and on 8%Ni-P2.0 for the mNi-P2.0 catalysts, while the turnover frequency (TOF) of methyl laurate mainly increased with the P/Ni ratio and Ni content. We propose that TOF was influenced by the nickel phosphide phases, the catalyst acidity and the particle size as well as the synergetic effect between the Ni site and acid site. Again, the hydrodeoxygenation pathway of methyl

Recovery Of Electrodic Powder From Spent Nickel-Metal Hydride Batteries (NiMH

Directory of Open Access Journals (Sweden)

Shin S.M.

2015-06-01

Full Text Available This study was focused on recycling process newly proposed to recover electrodic powder enriched in nickel (Ni and rare earth elements (La and Ce from spent nickel-metal hydride batteries (NiMH. In addition, this new process was designed to prevent explosion of batteries during thermal treatment under inert atmosphere. Spent nickel metal hydride batteries were heated over range of 300°C to 600°C for 2 hours and each component was completely separated inside reactor after experiment. Electrodic powder was successfully recovered from bulk components containing several pieces of metals through sieving operation. The electrodic powder obtained was examined by X-ray diffraction (XRD and energy dispersive X-ray spectroscopy (EDX and image of the powder was taken by scanning electron microscopy (SEM. It was finally found that nickel and rare earth elements were mainly recovered to about 45 wt.% and 12 wt.% in electrodic powder, respectively.

Interconnected Ni_2P nanorods grown on nickel foam for binder free lithium ion batteries

International Nuclear Information System (INIS)

Li, Qin; Ma, Jingjing; Wang, Huijun; Yang, Xia; Yuan, Ruo; Chai, Yaqin

2016-01-01

Herein, we report a moderate and simple approach to synthesize nickel phosphide nanorods on nickel foam (Ni_2P/NF), which was employed as anode material for lithium ion batteries (LIBs). In this paper, interconnected Ni_2P nanorods were fabricated through hydrothermal treatment of NF and subsequently by high temperature phosphating. NF is not only regarded as nickel source and metal current collector, but also as a support to grow electro-active material (Ni_2P). Therefore, Ni_2P/NF could act as a self-supported working electrode for LIBs without any extra addition of cohesive binders. Moreover, benefiting from the conductive capacity of Ni_2P/NF, the active compound behaved superior lithium storage performance and cycling reversibility during electrochemical cycling process. The Ni_2P/NF delivered excellent reversibility of 507 mAh g"−"1 at the current density of 50 mA g"−"1 after 100 cycles. This work may provide a potential method for preparation of metal phosphides as promising materials for LIBs, hydrogen evolution reaction (HER) or other fields.

Differences in genotoxic activity of alpha-Ni3S2 on human lymphocytes from nickel-hypersensitized and nickel-unsensitized donors.

Science.gov (United States)

Arrouijal, F Z; Marzin, D; Hildebrand, H F; Pestel, J; Haguenoer, J M

1992-05-01

The genotoxic activity of alpha-Ni3S2 was assessed on human lymphocytes from nickel-hypersensitized (SSL) and nickel-unsensitized (USL) subjects. Three genotoxicity tests were performed: the sister chromatid exchange (SCE) test, the metaphase analysis test and the micronucleus test. (i) The SCE test (3-100 micrograms/ml) showed a weak but statistically significant increase in the number of SCE in both lymphocyte types with respect to controls, USL presenting a slightly higher SCE incidence but only at one concentration. (ii) The metaphase analysis test demonstrated a high dose-dependent clastogenic activity of alpha-Ni3S2 in both lymphocyte types. The frequency of chromosomal anomalies was significantly higher in USL than in SSL for all concentrations applied. (iii) The micronucleus test confirmed the dose-dependent clastogenic activity of alpha-Ni3S2 and the differences already observed between USL and SSL, i.e. the number of cells with micronuclei was statistically higher in USL. Finally, the incorporation study with alpha-63Ni3S2 showed a higher uptake of its solubilized fraction by USL. This allows an explanation of the different genotoxic action of nickel on the two cell types. In this study we demonstrated that hypersensitivity has an influence on the incorporation of alpha-Ni3S2 and subsequently on the different induction of chromosomal aberrations in human lymphocytes.

Effects of P/Ni ratio and Ni content on performance of γ-Al{sub 2}O{sub 3}-supported nickel phosphides for deoxygenation of methyl laurate to hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Zhang, Zhena; Tang, Mingxiao; Chen, Jixiang, E-mail: jxchen@tju.edu.cn

2016-01-01

Graphical abstract: - Highlights: • The formation of AlPO{sub 4} was unfavorable for that of nickel phosphides. • The phase compositions of nickel phosphide depended on the amount of reduced P. • Catalytic activity was determined by surface Ni site density and catalyst acidity. • HDO pathway was promoted by increasing P/Ni ratio and Ni content. • Nickel phosphide gave much higher carbon yield and lower H{sub 2} consumption than Ni. - Abstract: γ-Al{sub 2}O{sub 3}-supported nickel phosphides (mNi-Pn) were prepared by the TPR method and tested for the deoxygenation of methyl laurate to hydrocarbons. The effects of the P/Ni ratio (n = 1.0–2.5) and Ni content (m = 5–15 wt.%) in the precursors on their structure and performance were investigated. Ni/γ-Al{sub 2}O{sub 3} was also studied for comparison. It was found that the formation of AlPO{sub 4} in the precursor inhibited the reduction of phosphate and so the formation of nickel phosphides. With increasing the P/Ni ratio and Ni content, the Ni, Ni{sub 3}P, Ni{sub 12}P{sub 5} and Ni{sub 2}P phases orderly formed, accompanying with the increases of their particle size and the amount of weak acid sites (mainly due to P-OH group), while the CO uptake and the amount of medium strong acid sites (mainly related to Ni sites) reached maximum on 10%Ni-P1.5. In the deoxygenation reaction, compared with Ni/γ-Al{sub 2}O{sub 3}, the mNi-Pn catalysts showed much lower activities for decarbonylation, C−C hydrogenolysis and methanation due to the ligand and ensemble effects of P. The conversion and the selectivity to n-C11 and n-C12 hydrocarbons achieved maximum on 10%Ni-P 2.0 for the 10%Ni-Pn catalysts and on 8%Ni-P2.0 for the mNi-P2.0 catalysts, while the turnover frequency (TOF) of methyl laurate mainly increased with the P/Ni ratio and Ni content. We propose that TOF was influenced by the nickel phosphide phases, the catalyst acidity and the particle size as well as the synergetic effect between the Ni site and

Automated rapid method for the determination of Ni-63 in deconstruction of nuclear facilities- and environmental samples; Automatisiertes Schnellverfahren zur Bestimmung von Ni-63 in Rueckbau- und Umweltproben

Energy Technology Data Exchange (ETDEWEB)

Bach, M.; Flucht, R.; Burow, M.; Zoriy, M.V. [Forschungszentrum Juelich GmbH, Juelich (Germany)

2012-07-01

Because of the increasing demand on the deconstruction of nuclear facilities in the last few years, a rapid method for the determination of Ni-63 in environmental samples is required. At Juelich, Division of Safety and Radiation Protection we have established a routine method, based on the determination of Ni-63 in the environmental samples using extraction chromatography separation from 2000[1] and optimize the sample preparation. Samples of different matrices were prepared by wet chemical methods for the extraction chromatography separation. For the separation the samples were introduced manually via a peristaltic pump or by using developed automated separation system equipped with the extraction chromatography column of Ni-Resin. Nickel[2] forms a Dimethylglyoximkomplex (DMG) and can be separated. The activity of the Ni-63 then were measured bei means of liquid scintillation counter (LSC), the recovery was determined using MC-ICP-MS. The yields of the Ni-carrier for the develped procure was higher than 90% with the accuracy below 10%. The developed method allows the relatively simple and fast determination of Ni-63 in environmental samples with a detection limit of 0.1 Bq/l. (orig.)

Nickel distribution and isotopic fractionation in a Brazilian lateritic regolith: Coupling Ni isotopes and Ni K-edge XANES

Science.gov (United States)

Ratié, G.; Garnier, J.; Calmels, D.; Vantelon, D.; Guimarães, E.; Monvoisin, G.; Nouet, J.; Ponzevera, E.; Quantin, C.

2018-06-01

Ultramafic (UM) rocks are known to be nickel (Ni) rich and to weather quickly, which makes them a good candidate to look at the Ni isotope systematics during weathering processes at the Earth's surface. The present study aims at identifying the Ni solid speciation and discussing the weathering processes that produce Ni isotope fractionation in two deep laterite profiles under tropical conditions (Barro Alto, Goiás State, Brazil). While phyllosilicates and to a lower extent goethite are the main Ni-bearing phases in the saprolitic part of the profile, iron (Fe) oxides dominate the Ni budget in the lateritic unit. Nickel isotopic composition (δ60Ni values) has been measured in each unit of the regolith, i.e., rock, saprock, saprolite and laterite (n = 52). δ60Ni varies widely within the two laterite profiles, from -0.10 ± 0.05‰ to 1.43 ± 0.05‰, showing that significant Ni isotope fractionation occurs during the weathering of UM rocks. Overall, our results show that during weathering, the solid phase is depleted in heavy Ni isotopes due to the preferential sorption and incorporation of light Ni isotopes into Fe oxides; the same mechanisms likely apply to the incorporation of Ni into phyllosilicates (type 2:1). However, an isotopically heavy Ni pool is observed in the solid phase at the bottom of the saprolitic unit. This feature can be explained by two hypotheses that are not mutually exclusive: (i) a depletion in light Ni isotopes during the first stage of weathering due to the preferential dissolution of light Ni-containing minerals, and (ii) the sorption or incorporation of isotopically heavy Ni carried by percolating waters (groundwater samples have δ60Ni of 2.20 and 2.27‰), that were enriched in heavy Ni isotopes due to successive weathering processes in the overlying soil and laterite units.

Essential elucidation for preparation of supported nickel phosphide upon nickel phosphate precursor

International Nuclear Information System (INIS)

Liu, Xuguang; Xu, Lei; Zhang, Baoquan

2014-01-01

Preparation of supported nickel phosphide (Ni 2 P) depends on nickel phosphate precursor, generally related to its chemical composition and supports. Study of this dependence is essential and meaningful for the preparation of supported Ni 2 P with excellent catalytic activity. The chemical nature of nickel phosphate precursor is revealed by Raman and UV–vis spectra. It is found that initial P/Ni mole ratio ≥0.8 prohibits the Ni-O-Ni bridge bonding (i.e., nickel oxide). This chemical bonding will not result in Ni 2 P structure, verified by XRD characterization results. The alumina (namely, γ-Al 2 O 3 , θ-Al 2 O 3 , or α-Al 2 O 3 ) with distinct physiochemical properties also results in diverse chemical nature of nickel phosphate, and then different nickel phosphides. The influence of alumina support on producing Ni 2 P was explained by the theory of surface energy heterogeneity, calculated by the NLDFT method based on N 2 -sorption isotherm. The uniform surface energy of α-Al 2 O 3 results only in the nickel phosphosate precursor and thus the Ni 2 P phase. - Graphical abstract: Surface energy heterogeneity in alumina (namely α-Al 2 O 3 , θ-Al 2 O 3 , and γ-Al 2 O 3 ) supported multi-oxidic precursors with different reducibilities and thus diverse nickel phosphides (i.e., Ni 3 P, Ni 12 P 5 , Ni 2 P). - Highlights: • Preparing pure Ni 2 P. • Elucidating nickel phosphate precursor. • Associating with surface energy

Simulations on Nickel target preparation and separation of Ni(II)-Cu(II) matrix for production of radioisotope "6"4Cu

International Nuclear Information System (INIS)

Sunarhadijoso Soenarjo; Wira Y Rahman; Sriyono; Triyanto

2011-01-01

The simulations on Nickel target preparation and separation of Ni(II)-Cu(II) matrix has been carried out as a preliminary study for production of medical radioisotope Cu-64 based on nuclear reaction of "6"4Ni (p,n) "6"4Cu. The nickel target preparation was performed by means of electroplating method using acidic solution of nickel chloride - boric acid mixture and basic solution of nickel sulphate - nickel chloride mixture on a silver - surfaced-target holder. The simulated solution of Ni(II) - Cu(II) matrix was considered as the solution of post-proton-irradiated nickel target containing both irradiated nickel and radioactive copper, but in the presented work the proton irradiation of nickel target was omitted, while the radioactive copper was originally obtained from neutron irradiation of CuO target. The separation of radioactive copper from the nickel target matrix was based on anion exchange column chromatography in which the radiocopper was conditioned to form anion complex CuCl_4"2"- and retained on the column while the nickel was kept in the form of Ni"2"+ cation and eluted off from the column. The retained radioactive copper was then eluted out the column in the condition of dilute HCl changing back the copper anion complex into Cu"2"+ cation. It was found that the electroplating result from the acidic solution was more satisfied than that from the basic solution. By conditioning the matrix solution at HCl 6 M, the radioactive copper was found in the forms of Cu"2"+ and CuCl_4"2"- while the nickel was totally in the form of Ni"2"+. In the condition of HCl 9 M, the radioactive copper was mostly in the form of CuCl_4"2"- while the nickel was found as both Ni"2"+ and NiCl_4"2"-. The best condition of separation was in HCl 8 M in which the radioactive copper was mostly in the form of CuCl_4"2"- while the nickel was mostly in the form of Ni"2"+. The retained CuCl_4"2"- was then changed back into Cu_2_+ cation form and eluted out the column by using HCl 0.05 M

Chemical adsorption of NiO nanostructures on nickel foam-graphene for supercapacitor applications

CSIR Research Space (South Africa)

Bello, A

2013-10-01

Full Text Available of the 3D porous cell structure of the nickel foam which allows for the growth of highly conductive graphene and subsequently provides support for uniform adsorption of the NiO onto the graphene. The NF-G/NiO electrode material showed excellent properties...

Urinary nickel as bioindicator of workers' Ni exposure in a galvanizing plant in Brazil.

Science.gov (United States)

Oliveira, J P; de Siqueira, M E; da Silva, C S

2000-01-01

We measured urinary nickel (U-Ni) in ten workers (97 samples) from a galvanizing plant that uses nickel sulfate, and in ten control subjects (55 samples) to examine the association between occupational exposure to airborne Ni and Ni absorption. Samples from the exposed group were taken before and after the work shift on 5 successive workdays. At the same time airborne Ni (A-Ni) was measured using personal samplers. Ni levels in biological material and in the airborne were determined by a graphite furnace atomic absorption spectrometry validated method. In the control group the urine samples were collected twice a day, in the before and after the work shift, on 3 successive days. Ni exposure low to moderate was detected in all the examined places in the plant, the airborne levels varying between 2.8 and 116.7 micrograms/m3 and the urine levels, from samples taken postshift, between 4.5 and 43.2 micrograms/g creatinine (mean 14.7 micrograms/g creatinine). Significant differences in U-Ni creatinine were seen between the exposed and control groups (Student's t test, P galvanizing plants regardless of the day of the workweek on which the samples are collected.

Improvement of direct determination of trace nickel in environmental samples by diffuse reflection spectroscopy using chromaticity characteristics.

Science.gov (United States)

Ershova, N I; Ivanov, V M

2000-05-01

Cellulose and chromaton-N-super as solid supports for direct determination of the immobilized nickel complexes with dimethylglyoxime and benzyldioxime by diffuse reflection spectroscopy were compared. The advantage of chromaton-N-super with use of benzyldioxime is shown. Detection limit is 0.02 microg/mL. The proposed method was applied for the analysis of soil.

Removing nickel from nickel-coated carbon fibers

Science.gov (United States)

Hardianto, A.; Hertleer, C.; De Mey, G.; Van Langenhove, L.

2017-10-01

Conductive fibers/yarns are one of the most important materials for smart textiles because of their electrically conductive functionality combined with flexibility and light weight. They can be applied in many fields such as the medical sector, electronics, sensors and even as thermoelectric generators. Temperature sensors, for example, can be made using the thermocouple or thermopile principle which usually uses two different metal wires that can produce a temperature-dependent voltage. However, if metal wires are inserted into a textile structure, they will decrease the flexibility properties of the textile product. Nickel-coated Carbon Fiber (NiCF), a conductive textile yarn, has a potential use as a textile-based thermopile if we can create an alternating region of carbon and nickel along the fiber which in turn it can be used for substituting the metallic thermopile. The idea was to remove nickel from NiCF in order to obtain a yarn that contains alternating zones of carbon and nickel. Due to no literature reporting on how to remove nickel from NiCF, in this paper we investigated some chemicals to remove nickel from NiCF.

Hierarchical mesoporous graphene@Ni-Co-S arrays on nickel foam for high-performance supercapacitors

International Nuclear Information System (INIS)

Nguyen, Van Hoa; Lamiel, Charmaine; Shim, Jae-Jin

2015-01-01

Highlights: • Hierarchical mesoporous graphene@Ni-Co-S arays have been decorated on Ni foam. • The electrode exhibits a high specific capacitance of 9.2 F cm −1 at 100 mA cm −1 . • The electrode presents large electroactive surface area and excellent structural stability. - Abstract: Hierarchical mesoporous graphene and ternary nickel cobalt sulfide (Ni-Co-S) arrays on nickel foam were designed and fabricated by chemical vapor deposition and electrodeposition for supercapacitor applications. The electrodes exhibited rapid electron and ion transport, large electroactive surface area, and excellent structural stability owing to the highly conductive, mesoporous nature of graphene and the Ni-Co-S nanosheets, as well as to the open framework of the three-dimensional nanoarchitectures. The specific capacitance of the obtained electrode was as high as 9.2 F cm −1 at a high current density of 100 mA cm −1 , indicating promising applications as an efficient electrode for electrochemical capacitors

DMG-α--a computational geometry library for multimolecular systems.

Science.gov (United States)

Szczelina, Robert; Murzyn, Krzysztof

2014-11-24

The DMG-α library grants researchers in the field of computational biology, chemistry, and biophysics access to an open-sourced, easy to use, and intuitive software for performing fine-grained geometric analysis of molecular systems. The library is capable of computing power diagrams (weighted Voronoi diagrams) in three dimensions with 3D periodic boundary conditions, computing approximate projective 2D Voronoi diagrams on arbitrarily defined surfaces, performing shape properties recognition using α-shape theory and can do exact Solvent Accessible Surface Area (SASA) computation. The software is written mainly as a template-based C++ library for greater performance, but a rich Python interface (pydmga) is provided as a convenient way to manipulate the DMG-α routines. To illustrate possible applications of the DMG-α library, we present results of sample analyses which allowed to determine nontrivial geometric properties of two Escherichia coli-specific lipids as emerging from molecular dynamics simulations of relevant model bilayers.

Targeting (cellular) lysosomal acid ceramidase by B13: design, synthesis and evaluation of novel DMG-B13 ester prodrugs.

Science.gov (United States)

Bai, Aiping; Szulc, Zdzislaw M; Bielawski, Jacek; Pierce, Jason S; Rembiesa, Barbara; Terzieva, Silva; Mao, Cungui; Xu, Ruijuan; Wu, Bill; Clarke, Christopher J; Newcomb, Benjamin; Liu, Xiang; Norris, James; Hannun, Yusuf A; Bielawska, Alicja

2014-12-15

Acid ceramidase (ACDase) is being recognized as a therapeutic target for cancer. B13 represents a moderate inhibitor of ACDase. The present study concentrates on the lysosomal targeting of B13 via its N,N-dimethylglycine (DMG) esters (DMG-B13 prodrugs). Novel analogs, the isomeric mono-DMG-B13, LCL522 (3-O-DMG-B13·HCl) and LCL596 (1-O-DMG-B13·HCl) and di-DMG-B13, LCL521 (1,3-O, O-DMG-B13·2HCl) conjugates, were designed and synthesized through N,N-dimethyl glycine (DMG) esterification of the hydroxyl groups of B13. In MCF7 cells, DMG-B13 prodrugs were efficiently metabolized to B13. The early inhibitory effect of DMG-B13 prodrugs on cellular ceramidases was ACDase specific by their lysosomal targeting. The corresponding dramatic decrease of cellular Sph (80-97% Control/1h) by DMG-B13 prodrugs was mainly from the inhibition of the lysosomal ACDase. Copyright © 2014 Elsevier Ltd. All rights reserved.

Recovery Of Nickel From Spent Nickel-Cadmium Batteries Using A Direct Reduction Process

Directory of Open Access Journals (Sweden)

Shin D.J.

2015-06-01

Full Text Available Most nickel is produced as Ferro-Nickel through a smelting process from Ni-bearing ore. However, these days, there have been some problems in nickel production due to exhaustion and the low-grade of Ni-bearing ore. Moreover, the smelting process results in a large amount of wastewater, slag and environmental risk. Therefore, in this research, spent Ni-Cd batteries were used as a base material instead of Ni-bearing ore for the recovery of Fe-Ni alloy through a direct reduction process. Spent Ni-Cd batteries contain 24wt% Ni, 18.5wt% Cd, 12.1% C and 27.5wt% polymers such as KOH. For pre-treatment, Cd was vaporized at 1024K. In order to evaluate the reduction conditions of nickel oxide and iron oxide, pre-treated spent Ni-Cd batteries were experimented on under various temperatures, gas-atmospheres and crucible materials. By a series of process, alloys containing 75 wt% Ni and 20 wt% Fe were produced. From the results, the reduction mechanism of nickel oxide and iron oxide were investigated.

Two investigational glycylcyclines, DMG-DMDOT and DMG-MINO. Antimicrobial activity studies against gram-positive species.

Science.gov (United States)

Johnson, D M; Jones, R N

1996-01-01

DMG-DMDOT (CL-331,002 OR CL-331,928) and DMG-MINO (CL-329,998 or CL-344,677) are two new semisynthetic tetracyclines called glycylcyclines, with a broad spectrum of activity and includes Enterobacteriaceae, Gram-positive cocci, JK diphtheroids, and Bacillus cereus. Potent activity was demonstrated against all Streptococcus spp. strains [minimum inhibitory concentrations] (MIC90S) 0.06-0.25 micrograms/ml) and staphylococci (oxacillin susceptible ans resistant; MIC90S 0.12-2 micrograms/ml). Both glycylcyclines (MIC90, 0.06 micrograms/ml) were more potent than minocycline (MIC90 8 micrograms/ml) against Enterococcus faecium, many of which were vancomycin resistant (116 strains). Organisms with minocycline MICs at > or = 8 micrograms/ml (Staphylococcus aureus, enterococci, beta-hemolytic streptococci, and pneumococci) had glycylcycline MIC results ranging from 0.06 to 0.5 micrograms/ml (e.g., apparent use against existing tetracycline-resistance phenotypes). Drugs in this class appear promising for therapy of infections caused by Gram-positive species now testing resistant to contemporary antimicrobial agents, and further development of compounds in this class is encouraged.

Effects of P/Ni ratio and Ni content on performance of γ-Al2O3-supported nickel phosphides for deoxygenation of methyl laurate to hydrocarbons

Science.gov (United States)

Zhang, Zhena; Tang, Mingxiao; Chen, Jixiang

2016-01-01

γ-Al2O3-supported nickel phosphides (mNi-Pn) were prepared by the TPR method and tested for the deoxygenation of methyl laurate to hydrocarbons. The effects of the P/Ni ratio (n = 1.0-2.5) and Ni content (m = 5-15 wt.%) in the precursors on their structure and performance were investigated. Ni/γ-Al2O3 was also studied for comparison. It was found that the formation of AlPO4 in the precursor inhibited the reduction of phosphate and so the formation of nickel phosphides. With increasing the P/Ni ratio and Ni content, the Ni, Ni3P, Ni12P5 and Ni2P phases orderly formed, accompanying with the increases of their particle size and the amount of weak acid sites (mainly due to P-OH group), while the CO uptake and the amount of medium strong acid sites (mainly related to Ni sites) reached maximum on 10%Ni-P1.5. In the deoxygenation reaction, compared with Ni/γ-Al2O3, the mNi-Pn catalysts showed much lower activities for decarbonylation, Csbnd C hydrogenolysis and methanation due to the ligand and ensemble effects of P. The conversion and the selectivity to n-C11 and n-C12 hydrocarbons achieved maximum on 10%Ni-P 2.0 for the 10%Ni-Pn catalysts and on 8%Ni-P2.0 for the mNi-P2.0 catalysts, while the turnover frequency (TOF) of methyl laurate mainly increased with the P/Ni ratio and Ni content. We propose that TOF was influenced by the nickel phosphide phases, the catalyst acidity and the particle size as well as the synergetic effect between the Ni site and acid site. Again, the hydrodeoxygenation pathway of methyl laurate was promoted with increasing P/Ni ratio and Ni content, ascribed to the phase change in the order of Ni, Ni3P, Ni12P5 and Ni2P in the prepared catalysts.

Influence of the alloying effect on nickel K-shell fluorescence yield in Ni Si alloys

Science.gov (United States)

Kalayci, Y.; Agus, Y.; Ozgur, S.; Efe, N.; Zararsiz, A.; Arikan, P.; Mutlu, R. H.

2005-02-01

Alloying effects on the K-shell fluorescence yield ωK of nickel in Ni-Si binary alloy system have been studied by energy dispersive X-ray fluorescence. It is found that ωK increases from pure Ni to Ni 2Si and then decreases from Ni 2Si to NiSi. These results are discussed in terms of d-occupation number on the Ni site and it is concluded that electronic configuration as a result of p-d hybridization explain qualitatively the observed variation of ωK in Ni-Si alloys.

The effect of Ni-Al ratio on the properties of coprecipitated nickel-alumina catalysts with high nickel contents

NARCIS (Netherlands)

Lansink Rotgerink, H.G.J.; Bosch, H.; van Ommen, J.G.; Ross, J.R.H.

1986-01-01

A series of nickel-alumina catalysts with a Ni/Al ratio between 3 and 20 has been prepared by coprecipitation. The calcination and reduction of these samples have been studied by thermogravimetry and their structures after calcination and reduction at different temperatures has been examined by

Diffusion of titanium and nickel in B2 NiTi

Czech Academy of Sciences Publication Activity Database

Divinski, S.V.; Stloukal, Ivo; Král, Lubomír; Herzig, Ch.

289-292, - (2009), s. 377-382 ISSN 1012-0386. [DIMAT 2008, International Conference on Diffusion in Materials /7./. Lanzarote, Canary Islands , 28.10.2008-31.10.2008] Institutional research plan: CEZ:AV0Z20410507 Keywords : intermetallic compound NiTi * nickel nad titanium diffusion * diffusion mechanism Subject RIV: BJ - Thermodynamics http://www.scientific.net/DDF.289-292.377/

Synthesis and Characterization of Nanostructured Nickel Diselenide NiSe2 from the Decomposition of Nickel Acetate, (CH3CO22Ni

Directory of Open Access Journals (Sweden)

Ming Yin

2014-01-01

Full Text Available Solution processed NiSe2 nanorods were synthesized by a modified colloidal synthesis technique, by chemical reaction of TOPSe and nickel acetate at 150°C. The rods exist as an oleic acid ligand stabilized solution, with oleic acid acting as a capping group. Structural characterization by X-ray diffraction and transmission electron microscopy indicates that the particles are rod-like shaped crystals with a high and relatively constant aspect ratio (30 : 1. TEM shows that the width and the length of the nanorods are in the range 10–20 nm and 300–350 nm, respectively. XRD indicates that the nanorods are pure and well crystallized. The size of nanorods based on the Debye-Scherrer effect, was 150 nm, the average value of length and width. They display thermal stability over prolonged heating times (<100 hours at 150°C, for which the average particle size is roughly constant. After about 100 hours of heating time there is an onset and growth of micron sized cubes and concurrent decomposition of NiSe2 to Ni and NiSe at 150°C.

Structural evolution and reaction mechanism of lithium nickelate (LiNiO2 during the carbonation reaction

Directory of Open Access Journals (Sweden)

Daniela González-Varela

2018-03-01

Full Text Available Lithium nickelate (LiNiO2 was synthesized using the lithium excess method, and then characterized by X-ray diffraction, scanning electron microscopy and N2 adsorption-desorption. Finally, differential thermal and thermogravimetric analyses were performed in CO2 presence, at high temperatures. Results show that LiNiO2 is able to react with CO2 through a complex structural evolution process, where lithium atoms are released to produce Li2CO3, while some nickel atoms are rearranged on different Li1-xNi1+xO2 crystalline phases. LiNiO2-CO2 reaction kinetic parameters were determined assuming a first-order reaction, where kinetic constants tended to increase as a function of temperature. However, kinetic constant values did not follow a linear trend. This atypical behavior was attributed to LiNiO2 sintering and crystalline evolution performed as a function of temperature.

Mass spectral analysis of cationic and neutral technetium complexes

International Nuclear Information System (INIS)

Unger, S.E.; McCormick, T.J.; Nunn, A.N.; Treher, E.N.

1986-01-01

Cationic and neutral technetium compounds have been characterized by mass spectrometry using a variety of ionization methods. These compounds include octahedral cationic complexes containing phosphorous and arsenic ligands such as DIPHOS and DIARS and neutral complexes containing PnAO and dimethylglyoxime, DMG, or cyclohexanedione dioxime, CDO, ligands. Boronate esters incorporating methyl and butyl derivatives of the DMG and CDO dioximes represent a new class of seven-coordinate Tc radiopharmaceuticals whose characterization by mass spectrometry has not previously been described. These complexes show promise as myocardial imaging agents. (author)

Hydrometallurgical recovery of metal values from sulfuric acid leaching liquor of spent lithium-ion batteries.

Science.gov (United States)

Chen, Xiangping; Chen, Yongbin; Zhou, Tao; Liu, Depei; Hu, Hang; Fan, Shaoyun

2015-04-01

Environmentally hazardous substances contained in spent Li-ion batteries, such as heavy metals and nocuous organics, will pose a threat to the environment and human health. On the other hand, the sustainable recycling of spent lithium-ion batteries may bring about environmental and economic benefits. In this study, a hydrometallurgical process was adopted for the comprehensive recovery of nickel, manganese, cobalt and lithium from sulfuric acid leaching liquor from waste cathode materials of spent lithium-ion batteries. First, nickel ions were selectively precipitated and recovered using dimethylglyoxime reagent. Recycled dimethylglyoxime could be re-used as precipitant for nickel and revealed similar precipitation performance compared with fresh dimethylglyoxime. Then the separation of manganese and cobalt was conducted by solvent extraction method using cobalt loaded D2EHPA. And McCabe-Thiele isotherm was employed for the prediction of the degree of separation and the number of extraction stages needed at specific experimental conditions. Finally, cobalt and lithium were sequentially precipitated and recovered as CoC2O4 ⋅ 2H2O and Li2CO3 using ammonium oxalate solution and saturated sodium carbonate solution, respectively. Recovery efficiencies could be attained as follows: 98.7% for Ni; 97.1% for Mn, 98.2% for Co and 81.0% for Li under optimized experimental conditions. This hydrometallurgical process may promise a candidate for the effective separation and recovery of metal values from the sulfuric acid leaching liquor. Copyright © 2015 Elsevier Ltd. All rights reserved.

Separation/enrichment of trace Zinc using potassium bromide-dimethylglyoxime-thymolphthalein system

Science.gov (United States)

Tu, Changqing; Wen, Xinrong

2018-02-01

A new method for the separation enrichment of trace Zn2+ using microcrystalline thymolphthalein as an adsorbent was established. The separation enrichment behaviour of Zn2+ and the conditions for the separation quantitatively of Zn2+ with other metal ions were investigated. The possible separation enrichment mechanism of Zn2+ was discussed in detail. The results showed that by controlling pH 10.0, in KBr-diacetydioxime(DMG)-thymolphthalein(TP) system, chelate settlement of Zn(DMG)2 which formed by Zn2+ and DMG was quantitatively adsorbed on the surface of microcrystalline thymolphthalein,and the liquid-solid phases were formed with clear interface, while Cu2+, Bi3+, Al3+, Hg2+ could not be adsorbed. The quantitative separation of Zn2+ from those metal ions was achieved. The proposed method has been successfully applied to the quantitative separation of trace Zn2+ in synthetic water samples with enrichment yield of 93.5%∼99.3%.

Dentin matrix gelatin (DMG) as a possible "universal" grafting material in periodontics.

Science.gov (United States)

Gould, T R; Westbury, L; Tillman, J

1982-01-01

The ideal of periodontal surgery is the total regeneration of the lost periodontal complex. A promising new osseous grafting material is Dental Matrix Gelation (DMG). DMG was prepared by a method similar to that of Conover and Urist (1979). This consisted of sequential extraction in 1:1 chloroform-methanol, 25 degrees C for 1 hour; 0.6 N HCl, 2 degrees C for 24 hours with constant agitation; 2 M CaCl2, 2 degrees C for 1 hour; 0.5 M EDTA pH 7.4, 2 degrees C for 1 hour; washed in distilled water 1 hour. Twelve rats were anesthetized, had heads shaved, midline flaps reflected, and 2 mm holes drilled through the right and left parietal bones. This type of osseous defect normally heals only by fibrous scarring and has been used to define osteoinductive materials. The DMG was cut into pieces about 1 mm square and placed into the right side defect while the left side remained open as a control. The animals were sacrificed on a schedule of two rats every 2 weeks until the 10th week when four rats were killed. The results showed complete osseous closure of the DMG site while the control healed by fibrous scarring. DMG seems to have strong osteoinductive power, and used allogenically has great potential as a commercially viable implant material.

Immunopotentiation by a new antitumor polysaccharide, DMG, a degraded D-manno-D-glucan from Microellobosporia grisea culture fluid.

Science.gov (United States)

Nakajima, H; Kita, Y; Takashi, T; Akasaki, M; Yamaguchi, F; Ozawa, S; Tsukada, W; Abe, S; Mizuno, D

1984-03-01

The immunopharmacological behavior of DMG, an antitumor polysaccharide, was studied in mice. DMG administered ip or sc stimulated peritoneal macrophages to produce high levels of interleukin-1 activity, which can amplify successive immune responses. DMG dose-dependently and schedule-dependently increased the cellular immune response against allogeneic tumor cells and the humoral immune response to sheep erythrocytes. DMG also enhanced nonspecific antitumor effector functions, such as natural killer activity of spleen and peritoneal cells, and the cytostatic activity of peritoneal macrophages. Peritoneal macrophages activated by ip or sc injection of DMG exhibited high cytostatic activity, especially after exposure in vitro to lymphokine supernatants containing macrophage activation factor. Moreover, granulocyte/macrophage colony-stimulating activity in the serum increased 2-10 hr after DMG administration. Thus, DMG potentiated antigen-specific immunological functions and nonspecific functions of host defense systems against cancer both qualitatively and quantitatively.

A paste type negative electrode using a MmNi{sub 5} based hydrogen storage alloy for a nickel-metal hydride (Ni-MH) battery

Energy Technology Data Exchange (ETDEWEB)

Uchida, H.; Matsumoto, T.; Watanabe, S.; Kobayashi, K.; Hoshino, H. [Tokai Univ., Kanagawa (Japan). School of Engineering

2001-07-01

Different conducting materials (nickel, copper, cobalt, graphite) were mixed with a MmNi{sub 5} type hydrogen storage alloy, and negative electrodes for a nickel-metal hydride(Ni-MH) rechargeable battery were prepared and examined with respect to the discharge capacity of the electrodes. The change in the discharge capacity of the electrodes with different conducting materials was measured as a function of the number of electrochemical charge and discharge cycles. From the measurements, the electrodes with cobalt and graphite were found to yield much higher discharge capacities than those with nickel or cobalt. From a comparative discharge measurements for an electrode composed of only cobalt powder without the alloy and an electrode with a mixture of cobalt and the alloy, an appreciable contribution of the cobalt surface to the enhancement of charge and discharge capacities was found. (author)

Preparation, Characterization and Catalytic Activity of Nickel Molybdate (NiMoO4 Nanoparticles

Directory of Open Access Journals (Sweden)

Hicham Oudghiri-Hassani

2018-01-01

Full Text Available Nickel molybdate (NiMoO4 nanoparticles were synthesized via calcination of an oxalate complex in static air at 500 °C. The oxalate complex was analyzed by thermal gravimetric analysis (TGA and Fourier transform infrared spectroscopy (FTIR. The as-synthesized nickel molybdate was characterized by Brunauer–Emmett–Teller technique (BET, X-ray diffraction (XRD, and transmission electron microscopy (TEM and its catalytic efficiency was tested in the reduction reaction of the three-nitrophenol isomers. The nickel molybdate displays a very high activity in the catalytic reduction of the nitro functional group to an amino. The reduction progress was controlled using Ultraviolet-Visible (UV-Vis absorption.

Three-dimensional cotton-like nickel nanowire@Ni-Co hydroxide nanosheet arrays as binder-free electrode for high-performance asymmetric supercapacitor

Science.gov (United States)

Wan, Houzhao; Li, Lang; Xu, Yang; Tan, Qiuyang; Liu, Xiang; Zhang, Jun; Wang, Hanbin; Wang, Hao

2018-05-01

Three-dimensional (3D) cotton-like Ni-Co layered double hydroxide nanosheet arrays/nickel nanowires (3D Ni-Co LDH/NiNw) were successfully fabricated through a facile chemical bath deposition method. The 3D nickel nanowires are used as a conductive substrate with robust adhesion for high-pseudocapacitance Ni-Co LDH. The 3D Ni-Co LDH/NiNw electrode shows a high areal specific capacitance of 14 F cm-2 at 5 mA cm-2 and quality specific capacitance of 466.6 F g-1 at 0.125 A g-1 with respect to the whole quality of the electrode. The fabricated asymmetric supercapacitor exhibits a remarkable energy density of 0.387 mWh cm-2 using Ni-Co LDH/NiNw as the negative electrode. This high-performance composite electrode presents a new and affordable general approach for supercapacitors.

Synthesis and Characterization of Nanostructured Nickel Diselenide NiSe2 from the Decomposition of Nickel Acetate, (CH3CO2)2Ni

OpenAIRE

Yin, Ming; O’Brien, Stephen

2014-01-01

Solution processed NiSe2 nanorods were synthesized by a modified colloidal synthesis technique, by chemical reaction of TOPSe and nickel acetate at 150°C. The rods exist as an oleic acid ligand stabilized solution, with oleic acid acting as a capping group. Structural characterization by X-ray diffraction and transmission electron microscopy indicates that the particles are rod-like shaped crystals with a high and relatively constant aspect ratio (30 : 1). TEM shows that the width and the len...

The effect of urea on microstructures of Ni{sub 3}S{sub 2} on nickel foam and its hydrogen evolution reaction

Energy Technology Data Exchange (ETDEWEB)

Jinlong, Lv, E-mail: ljltsinghua@126.com [Beijing Key Laboratory of Fine Ceramics, Institute of Nuclear and New Energy Technology, Tsinghua University, Zhongguancun Street, Haidian District, Beijing 100084 (China); State Key Lab of New Ceramic and Fine Processing, Tsinghua University, Beijing 100084 (China); Tongxiang, Liang, E-mail: txliang@mail.tsinghua.edu.cn [Beijing Key Laboratory of Fine Ceramics, Institute of Nuclear and New Energy Technology, Tsinghua University, Zhongguancun Street, Haidian District, Beijing 100084 (China); State Key Lab of New Ceramic and Fine Processing, Tsinghua University, Beijing 100084 (China)

2016-11-15

The effects of urea concentration on microstructures of Ni{sub 3}S{sub 2}formed on nickel foam and its hydrogen evolution reaction were investigated. The Ni{sub 3}S{sub 2} nanosheets with porous structure were formed on nickel foam during hydrothermal process due to low urea concentration. While high urea concentration facilitated the forming of Ni{sub 3}S{sub 2} nanotube arrays. The resulting Ni{sub 3}S{sub 2} nanotube arrays exhibited higher catalytic activity than Ni3S2nanosheets for hydrogen evolution reaction. This was mainly attributed to a fact that Ni{sub 3}S{sub 2} nanotube arrays facilitated diffusion of electrolyte for hydrogen evolution reaction. - Graphical abstract: The resulting Ni{sub 3}S{sub 2} nanotube arrays exhibited higher catalytic activity than Ni{sub 3}S{sub 2} nanosheets for hydrogen evolution reaction. This was mainly attributed to a fact that Ni{sub 3}S{sub 2} nanotube arrays facilitated diffusion of electrolyte for hydrogen evolution reaction and hydrogen evolution. - Highlights: • Urea promoted to forming more Ni{sub 3}S{sub 2} nanotube arrays on nickel foam. • Ni{sub 3}S{sub 2} nanotube arrays showed higher catalytic activity in alkaline solution. • Ni{sub 3}S{sub 2} nanotube arrays promoted electron transport and reaction during the HER.

One-pot hydrothermal synthesis of reduced graphene oxide/Ni(OH)2 films on nickel foam for high performance supercapacitors

International Nuclear Information System (INIS)

Min, Shudi; Zhao, Chongjun; Chen, Guorong; Qian, Xiuzhen

2014-01-01

Reduced graphene oxide (RGO) on nickel hydroxide (Ni(OH) 2 ) film was synthesized via a green and facile hydrothermal approach. In this process, graphene oxide (GO) was reduced by nickel foam (NF) while the nickel metal was oxidized to Ni(OH) 2 film simultaneously, which resulted in RGO on Ni(OH) 2 structure. The RGO/Ni(OH) 2 composite film was characterized using by X-ray diffraction (XRD), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and field-emission scanning electron microscope (FESEM). The electrochemical performances of the supercapacitor with the as-synthesized RGO/Ni(OH) 2 composite films as electrodes were evaluated using cyclic voltammetry (CV), galvanostatic charge–discharge (GCD), electrochemical impedance spectrometry (EIS) in 1 M KOH aqueous solution. Results indicated that the RGO/Ni(OH) 2 /NF composite electrodes exhibited superior capacitive performance with high capability (2500 mF cm −2 at a current density of 5 mA cm −2 , or 1667 F g −1 at 3.3 A g −1 ), compared with pure Ni(OH) 2 /NF (450 mF cm −2 at 5 mA cm −2 , 409 F g −1 at 3.3 A g −1 ) prepared under the identical conditions. Our study highlights the importance of anchoring RGO films on Ni(OH) 2 surface for maximizing the optimized utilization of electrochemically active Ni(OH) 2 and graphene for energy storage application in supercapacitors

Host-mediated antitumor effect of DMG, a degraded D-manno-D-glucan from Microellobosporia grisea culture fluid.

Science.gov (United States)

Nakajima, H; Hashimoto, S; Nagao, S; Kita, Y; Khono, M; Ogawa, H; Abe, S; Mizuno, D

1984-03-01

DMG, a new polysaccharide with a well-characterized structure, isolated from the culture filtrate of an actinomycetes and then degraded by acid treatment, was tested for antitumor activity on allogeneic and syngeneic tumors in mice. In the allogeneic Ehrlich solid tumor system, DMG showed antitumor activity over a wide dose range, its optimal dose being 10-100 mg/kg. The optimal time of DMG administration was 1-2 weeks after tumor inoculation, but DMG was also effective when given before tumor inoculation. DMG was effective when given ip, sc, it (intratumorally) or iv. DMG also had antitumor effects on syngeneic tumors. It rapidly inhibited the growth of MM46 mammary carcinoma, MH134 hepatoma, and Meth A fibrosarcoma, and also inhibited spontaneous pulmonary metastases of B16-BL6 melanoma. However, it had no direct cytocidal action on tumor cells in vitro. Its antitumor activity was much less in athymic nude mice and in mice immunosuppressed by whole-body X-irradiation than in normal hosts.Thus, DMG was shown to exert antitumor activity via host-mediated mechanisms. Its antitumor activity is discussed in comparison with those of other antitumor polysaccharides.

NICKEL – ENVIRONMENTAL ALLERGEN

Directory of Open Access Journals (Sweden)

Henryka Langauer-Lewowicka

2010-06-01

Full Text Available Nickel (Ni is ubiquitus in our biosphere because of its emission from natural and anthropogenic sources. Its toxic and carcinogenic properties are well recognised only in workers exposed to high Ni concentrations. Nickel allergy is the most common form of cutaneus hypersensitivity in general population and also in occupationally exposed groups. As sensitizing agent Ni has a high prevalence of allergic contact dermatitis. The most important known risk factor associated with nickel allergy is ear piercing and use of other jewelry in females. In general population 17 % adults and 8 % children have Ni allergy symptoms. Permanently growing Ni allergy is regarded as serious risk for public health.

Reversible Changes in Resistance of Perovskite Nickelate NdNiO3 Thin Films Induced by Fluorine Substitution.

Science.gov (United States)

Onozuka, Tomoya; Chikamatsu, Akira; Katayama, Tsukasa; Hirose, Yasushi; Harayama, Isao; Sekiba, Daiichiro; Ikenaga, Eiji; Minohara, Makoto; Kumigashira, Hiroshi; Hasegawa, Tetsuya

2017-03-29

Perovskite nickel oxides are of fundamental as well as technological interest because they show large resistance modulation associated with phase transition as a function of the temperature and chemical composition. Here, the effects of fluorine doping in perovskite nickelate NdNiO 3 epitaxial thin films are investigated through a low-temperature reaction with polyvinylidene fluoride as the fluorine source. The fluorine content in the fluorinated NdNiO 3-x F x films is controlled with precision by varying the reaction time. The fully fluorinated film (x ≈ 1) is highly insulating and has a bandgap of 2.1 eV, in contrast to NdNiO 3 , which exhibits metallic transport properties. Hard X-ray photoelectron and soft X-ray absorption spectroscopies reveal the suppression of the density of states at the Fermi level as well as the reduction of nickel ions (valence state changes from +3 to +2) after fluorination, suggesting that the strong Coulombic repulsion in the Ni 3d orbitals associated with the fluorine substitution drives the metal-to-insulator transition. In addition, the resistivity of the fluorinated films recovers to the original value for NdNiO 3 after annealing in an oxygen atmosphere. By application of the reversible fluorination process to transition-metal oxides, the search for resistance-switching materials could be accelerated.

Nickel accumulation and storage in bradyrhizobium japonicum

International Nuclear Information System (INIS)

Maier, R.J.; Pihl, T.D.; Stults, L.; Sray, W.

1990-01-01

Hydrogenase-depressed (chemolithotrophic growth conditions) and heterotrophically grown cultures of Bradyrhizobium japonicum accumulated nickel about equally over a 3-h period. Both types of cultures accumulated nickel primarily in a form that was not exchangeable with NiCl 2 , and they accumulated much more Ni than would be needed for the Ni-containing hydrogenase. The nickel accumulated by heterotrophically incubated cultures could later be mobilized to allow active hydrogenase synthesis during derepression in the absence of nickel, while cells both grown with Ni and the derepressed without nickel had low hydrogenase activities. The level of activity in cells grown with Ni and then derepressed without nickel was about the same as that in cultures derepressed in the presence of nickel. The Ni accumulated by heterotrophically grown cultures was associated principally with soluble proteins rather than particulate material, and this Ni was not lost upon dialyzing an extract containing the soluble proteins against either Ni-containing or EDTA-containing buffer. However, this Ni was lost upon pronase or low pH treatments. The soluble Ni-binding proteins were partially purified by gel filtration and DEAE chromatography. They were not antigenically related to hydrogenase peptides. Much of the 63 Ni eluted as a single peak of 48 kilodaltons. Experiments involving immunuprecipitation of 63 Ni-containing hydrogenase suggested that the stored source of Ni in heterotrophic cultures that could later be mobilized into hydrogenase resided in the nonexchangeable Ni-containing fraction rather than in loosely bound or ionic forms

The release of nickel from orthodontic NiTi wires is increased by dynamic mechanical loading but not constrained by surface nitridation.

Science.gov (United States)

Peitsch, T; Klocke, A; Kahl-Nieke, B; Prymak, O; Epple, M

2007-09-01

The influence of dynamic mechanical loading and of surface nitridation on the nickel release from superelastic nickel-titanium orthodontic wires was investigated under ultrapure conditions. Commercially available superelastic NiTi arch wires (size 0.018 x 0.025'') without surface modification (Neo Sentalloy) and with nitrogen ion implantation surface treatment (Neo Sentalloy Ionguard) were analyzed. Mechanical loading of wire segments with a force similar to the physiological situation was performed with a frequency of 5 Hz in ultrapure water and saline solution, respectively. The release of nickel was monitored by atomic absorption spectroscopy for up to 36 days. The mechanically loaded wires released significantly more nickel ( approximately 45 ng cm(-2) d(-1)) than did nonloaded wires (<1 ng cm(-2) d(-1)). There was no statistically significant effect of the testing solution (water or NaCl) or of the surface nitridation. The total amount of released nickel was small in all cases, but may nevertheless account for the occasional clinical observations of adverse reactions during application of NiTi-based orthodontic appliances. The surface nitridation did not constrain the release of nickel from NiTi under continuous mechanical stress.

Nickel-centred proton reduction catalysis in a model of [NiFe] hydrogenase

Science.gov (United States)

Brazzolotto, Deborah; Gennari, Marcello; Queyriaux, Nicolas; Simmons, Trevor R.; Pécaut, Jacques; Demeshko, Serhiy; Meyer, Franc; Orio, Maylis; Artero, Vincent; Duboc, Carole

2016-11-01

Hydrogen production through water splitting is one of the most promising solutions for the storage of renewable energy. [NiFe] hydrogenases are organometallic enzymes containing nickel and iron centres that catalyse hydrogen evolution with performances that rival those of platinum. These enzymes provide inspiration for the design of new molecular catalysts that do not require precious metals. However, all heterodinuclear NiFe models reported so far do not reproduce the Ni-centred reactivity found at the active site of [NiFe] hydrogenases. Here, we report a structural and functional NiFe mimic that displays reactivity at the Ni site. This is shown by the detection of two catalytic intermediates that reproduce structural and electronic features of the Ni-L and Ni-R states of the enzyme during catalytic turnover. Under electrocatalytic conditions, this mimic displays high rates for H2 evolution (second-order rate constant of 2.5 × 104 M-1 s-1 turnover frequency of 250 s-1 at 10 mM H+ concentration) from mildly acidic solutions.

Nickel and cobalt release from children's toys purchased in Denmark and the United States.

Science.gov (United States)

Jensen, Peter; Hamann, Dathan; Hamann, Carsten R; Jellesen, Morten S; Jacob, Sharon E; Thyssen, Jacob P

2014-01-01

Nickel is the most common allergen detected by patch testing in children. There is an increasing number of cases in children who have not had exposure to piercing. Although the clinical relevance of nickel patch test reactions in children is sometimes uncertain, continued vigilance to identify new sources of nickel exposure in this age group is important. Recent case reports have described allergic nickel contact dermatitis in children following exposure to toys, but the magnitude of this problem is unknown. The aim of this study was to evaluate nickel and cobalt release from children's toys. We purchased 212 toys in 18 different retail and online stores in the United States and Denmark. Nickel and cobalt release was tested using the dimethylglyoxime and cobalt screening spot tests. A total of 73 toys (34.4%) released nickel, and none released cobalt. Toys are a commonly overlooked source of nickel exposure and sensitization. Therefore, dermatologists, allergists, and pediatricians should consider the role of toys in their evaluation of children with dermatitis, and the parents of children with positive nickel patch test reactions should be told that toys may release nickel and be a potential chemical source in the manifestation of allergic contact dermatitis.

Solubility of nickel ferrite (NiFe2O4) from 100 to 200 deg. C

International Nuclear Information System (INIS)

Bellefleur, Alexandre; Bachet, Martin; Benezeth, Pascale; Schott, Jacques

2012-09-01

The solubility of nickel ferrite was measured in a Hydrogen-Electrode Concentration Cell (HECC) at temperatures of 100 deg. C, 150 deg. C and 200 deg. C and pH between 4 and 5.25. The experimental solution was composed of HCl and NaCl (0.1 mol.L -1 ). Based on other studies ([1,2]), pure nickel ferrite was experimentally synthesized by calcination of a mixture of hematite Fe 2 O 3 and bunsenite NiO in molten salts at 1000 deg. C for 15 hours in air. The so obtained powder was fully characterized. The Hydrogen-Electrode Concentration cell has been described in [3]. It allowed us to run solubility experiments up to 250 deg. C with an in-situ pH measurement. To avoid reduction of the solid phase to metallic nickel, a hydrogen/argon mixture was used instead of pure hydrogen. Consequently, the equilibration time for the electrodes was longer than with pure hydrogen. Eight samples were taken on a 70 days period. After the experiments, the powder showed no significant XRD evidence of Ni (II) reduction. Nickel concentration was measured by atomic absorption spectroscopy and iron concentration was measured by UV spectroscopy. The protocol has been designed to be able to measure both dissolved Fe (II) and total iron. The nickel solubility of nickel ferrite was slightly lower than the solubility of nickel oxide in close experimental conditions [3]. Dissolved iron was mainly ferrous and the solution was under-saturated relative to both hematite and magnetite. The nickel/iron ratio indicated a non-stoichiometric dissolution. The solubility measurements were compared with equilibrium calculations using the MULTEQ database. [1] Hayashi et al (1980) J. Materials Sci. 15, 1491-1497. [2] Ziemniak et al (2007) J. Physics and Chem. of Solids. 68,10-21. [3] EPRI Report 1003155 (2002). (authors)

The solubility of palladium(II) bis-dimethylglyoximate

International Nuclear Information System (INIS)

Maghzian, R.

1978-01-01

The solubility of palladium(II) bis-dimethylglyoximate in different solutions has been determined. Values obtained for the solubility of the palladium complex are tabulated. The solubility is the lowest in water, ammonium acetate and a 25% acetone-water mixture. It is highest in dilute HCl and acetone but precipitation from aqueous acetone should be satisfactory for most purposes if the acetone content of the solvent is roughly less than 50% by volume. The solubility in dilute HCl reflects the concern by previous workers for losses in precipitation from mineral acid. In general, however, the losses are unlikely to be significant unless the quantity of palladium to be precipitated and weighed is small. (T.G.)

Mesoporous Nickel Oxide (NiO) Nanopetals for Ultrasensitive Glucose Sensing

Science.gov (United States)

Mishra, Suryakant; Yogi, Priyanka; Sagdeo, P. R.; Kumar, Rajesh

2018-01-01

Glucose sensing properties of mesoporous well-aligned, dense nickel oxide (NiO) nanostructures (NSs) in nanopetals (NPs) shape grown hydrothermally on the FTO-coated glass substrate has been demonstrated. The structural study based investigations of NiO-NPs has been carried out by X-ray diffraction (XRD), electron and atomic force microscopies, energy dispersive X-ray (EDX), and X-ray photospectroscopy (XPS). Brunauer-Emmett-Teller (BET) measurements, employed for surface analysis, suggest NiO's suitability for surface activity based glucose sensing applications. The glucose sensor, which immobilized glucose on NiO-NPs@FTO electrode, shows detection of wide range of glucose concentrations with good linearity and high sensitivity of 3.9 μA/μM/cm2 at 0.5 V operating potential. Detection limit of as low as 1 μΜ and a fast response time of less than 1 s was observed. The glucose sensor electrode possesses good anti-interference ability, stability, repeatability & reproducibility and shows inert behavior toward ascorbic acid (AA), uric acid (UA) and dopamine acid (DA) making it a perfect non-enzymatic glucose sensor.

Potentiation of antitumor immunity in tumor-bearing mice by a degraded D-manno-D-glucan (DMG), a new antitumor polysaccharide.

Science.gov (United States)

Nakajima, H; Kita, Y; Hashimoto, S; Tsukada, W; Abe, S; Mizuno, D

1983-12-01

DMG, a degraded D-manno-D-glucan from the culture fluid of Microellobosporia grisea, inhibited the growth of murine syngeneic MM46 mammary carcinoma. Mice in which the tumor had completely regressed by DMG treatment showed tumor-specific antitumor resistance. The antitumor action of DMG was studied by examining the influences of DMG on tumor-specific and non-specific immune responses in tumor-bearing hosts. The tumor-specific delayed hypersensitivity reaction appeared transiently on day 7 after tumor inoculation but had decreased by day 15 in untreated tumor-bearing mice. In contrast, the reaction was retained and augmented in DMG-treated tumor-bearing mice. The tumor-neutralizing activity of spleen cells from DMG-treated tumor-bearing mice, tested by a Winn assay, was tumor-specific and significantly higher than that of untreated tumor-bearing mice. The tumor-neutralizing activity of peritoneal cells and the in vitro cytostatic activity of peritoneal macrophages in response to lymphokine supernatants containing macrophage activation factor were also augmented by DMG treatment. In contrast, the level of antitumor antibody in the serum increased with time, irrespective of DMG administration. Thus, DMG potentiated cellular antitumor effector mechanisms.

Steady-state growth of NiO scales on ceria-coated polycrystalline nickel

International Nuclear Information System (INIS)

Czerwinski, F.; Szpunar, J.A.; Smeltzer, W.W.

1996-01-01

The effect of CeO 2 ceramic coatings with thicknesses in the range of 14 to 42 nm on the oxidation of high purity polycrystalline nickel at 973 K in 1 atm O 2 has been studied. The ceria coatings decrease the Ni oxidation rate after 125 h by a factor up to 45, which is significantly higher than the reduction achieved during early stages. Growth features, including oxide thickness, surface morphology, and the texture for both the pure and CeO 2 modified NiO, demonstrate a definite dependence on the crystallographic orientation of the Ni substrate. Oxides with thicknesses of up to 1 microm developed on CeO 2 -coated Ni consisted of three sublayers. The Ce-rich part, composed of small NiO grains and CeO 2 particles, was located inside the scale and shifted deeper into the scale with increased oxidation time. The growth kinetics and microstructural evolutions of modified NiO are discussed in terms of the mechanism of inhibition of grain boundary diffusion in NiO by Ce +4 ions

Rapid separation and determination of 107Pd in radioactive waste produced during NPP A-1 decommissioning

International Nuclear Information System (INIS)

Boris Andris; Miroslav Prazsky; Ferdinand Sebesta

2015-01-01

Procedure for 107 Pd determination in radioactive wastes coming from decommissioning of NPP A-1 is proposed and verified. 107 Pd was separated and purified by Pd precipitation with dimethylglyoxime (DMG) and/or ferric hydroxide precipitation. 107 Pd yield was determined gravimetrically by weighing the Pd(DMG) 2 precipitate. 107 Pd counting was performed using liquid scintillation counter (LSC-TDCR) and scintillation cocktail Hionic Fluor. In all analyzed samples the determined activities of 107 Pd were lower than MDA. Nevertheless such analyses permit the decision concerning the storage of solidified wastes in the Mochovce regional repository. (author)

Understanding CO-stripping mechanism from Ni{sub UPD}/Pt(1 1 0) in view of the measured nickel formal partial charge number upon underpotential deposition on platinum surfaces in sulphate media

Energy Technology Data Exchange (ETDEWEB)

Chatenet, Marian [Laboratoire d' Electrochimie et de Physicochimie des Materiaux et des Interfaces, LEPMI, UMR 5631 CNRS-INPG-UJF, BP 75, 38402 Saint-Martin d' Heres Cedex (France)], E-mail: Marian.Chatenet@lepmi.inpg.fr; Soldo-Olivier, Yvonne; Chainet, Eric; Faure, Rene [Laboratoire d' Electrochimie et de Physicochimie des Materiaux et des Interfaces, LEPMI, UMR 5631 CNRS-INPG-UJF, BP 75, 38402 Saint-Martin d' Heres Cedex (France)

2007-12-01

We recently showed nickel-underpotential deposition (Ni-UPD) occurs on polycrystalline or single crystal platinum electrodes in acidic media. Whereas the decoupling of the nickel and hydrogen adsorption/desorption peaks is difficult for low pH, these processes can be better separated for higher pH values, typically pH > 3. However, even for platinum single crystals, high pH solutions do not enable to sufficiently separate nickel from hydrogen phenomena. As a result, electrochemistry alone cannot yield important information about Ni-UPD, such as the formal partial charge number (valency of electrosorption) and the role of the sulphate or hydrogen sulphate anions. So, we decided to couple cyclic voltammetry to electrochemical quartz crystal microbalance (EQCM). EQCM measurements enable to decorrelate the simultaneous hydrogen and nickel adsorption/desorption peaks, which we could not attempt solely with electrochemistry. The coupling between gravimetric and electrochemical measurements allows us to detect the contribution of the anions and thus to isolate that of nickel: nickel coverage can then be determined. Nearly 4/5 Ni{sub UPD} monolayer ({theta}{sub Ni} {approx} 0.8) over platinum is reached at nickel equilibrium potential for high pH solutions (5.5). The QCM and electrochemistry coupling further allows the determination of nickel formal partial charge number: {iota}{sub Ni,EQCM} = 1.3 {+-} 0.13. Direct electrochemistry measurements (Swathirajan and Bruckenstein method) yield: {iota}{sub Ni,Pt(poly)} = 1.5 {+-} 0.17. These two values are close, which validates the electrochemical method for the nickel/platinum system. In consequence, we used Swathirajan and Bruckenstein method for Pt(1 1 0)-(1 x 2) crystal and found: {iota}{sub Ni,Pt(110)} {approx} 1.4 {+-} 0.1. Whatever the system (Ni{sub UPD}/Pt(poly) or Ni{sub UPD}/Pt(1 1 0)-(1 x 2)) or the experimental technique, nickel formal partial charge number is lower than nickel cation charge: {iota}{sub Ni} < z

Lung clearance and disposition of 63Ni in F344/N rats after intratracheal instillation of nickel sulfate solutions

International Nuclear Information System (INIS)

Medinsky, M.A.; Benson, J.M.; Hobbs, C.H.

1987-01-01

Epidemiology studies have indicated increased incidences of respiratory tract and renal cancer in nickel refinery workers. Since the most likely route of exposure to nickel in the workplace is via the respiratory tract, the objectives of the experiments described here were to determine the retention pattern of Ni in the lungs, identify the target organs for Ni absorbed from the respiratory tract, and determine rates for excretion of Ni. Male and female F344 rats were given 17, 190, or 1800 nmoles Ni (as a nickel sulfate solution) in saline, containing trace amounts of 63 Ni, by intratracheal instillation. Urine and feces were collected, and rats were necropsied at predetermined times up to 96 hr after instillation. At all times, lungs, trachea, larynx, kidney, and urinary bladder contained the highest concentrations of Ni as determined by liquid scintillation spectrometry. Urine was the major route for excretion of Ni, accounting for 50% of the dose after instillation of 17 or 190 nmoles Ni, and 80% of the dose after instillation of 1800 nmoles Ni. The half-time for urinary excretion of Ni increased from 4.6 hr at the highest dose to 23 hr at the lowest dose used. Fecal excretion accounted for 30% (17- and 190-nmole doses) or 13% (1800 nmoles) of the initial dose. Of the Ni remaining in the body at the end of 96 hr, over 50% was in the lungs. The long-term half-time for clearance of Ni from the lungs ranged from 21 hr at the highest dose to 36 hr at the lowest dose instilled. As the amount of instilled Ni decreased, the fraction of the instilled Ni associated with the long-term clearance component increased (from 24% at the highest dose to 40% at the lowest dose). Results suggest that, over the range of doses studied, both pulmonary clearance of Ni and routes for excretion of Ni were dependent on the instilled dose

Co-reduction of Copper Smelting Slag and Nickel Laterite to Prepare Fe-Ni-Cu Alloy for Weathering Steel

Science.gov (United States)

Guo, Zhengqi; Pan, Jian; Zhu, Deqing; Zhang, Feng

2018-02-01

In this study, a new technique was proposed for the economical and environmentally friendly recovery of valuable metals from copper smelting slag while simultaneously upgrading nickel laterite through a co-reduction followed by wet magnetic separation process. Copper slag with a high FeO content can decrease the liquidus temperature of the SiO2-Al2O3-CaO-MgO system and facilitate formation of liquid phase in a co-reduction process with nickel laterite, which is beneficial for metallic particle growth. As a result, the recovery of Ni, Cu, and Fe was notably increased. A crude Fe-Ni-Cu alloy with 2.5% Ni, 1.1% Cu, and 87.9% Fe was produced, which can replace part of scrap steel, electrolytic copper, and nickel as the burden in the production of weathering steel by an electric arc furnace. The study further found that an appropriate proportion of copper slag and nickel laterite in the mixture is essential to enhance the reduction, acquire appropriate amounts of the liquid phase, and improve the growth of the metallic alloy grains. As a result, the liberation of alloy particles in the grinding process was effectively promoted and the metal recovery was increased significantly in the subsequent magnetic separation process.

Performance improvement of pasted nickel electrodes with multi-wall carbon nanotubes for rechargeable nickel batteries

International Nuclear Information System (INIS)

Song, Q.S.; Aravindaraj, G.K.; Sultana, H.; Chan, S.L.I.

2007-01-01

Carbon nanotubes (CNTs) were employed as a functional additive to improve the electrochemical performance of pasted nickel-foam electrodes for rechargeable nickel-based batteries. The nickel electrodes were prepared with spherical β-Ni(OH) 2 powder as the active material and various amounts of CNTs as additives. Galvanostatic charge/discharge cycling tests showed that in comparison with the electrode without CNTs, the pasted nickel electrode with added CNTs exhibited better electrochemical properties in the chargeability, specific discharge capacity, active material utilization, discharge voltage, high-rate capability and cycling stability. Meanwhile, the CNT addition also lowered the packing density of Ni(OH) 2 particles in the three-dimensional porous nickel-foam substrate, which could lead to the decrease in the active material loading and discharge capacity of the electrode. Hence, the amount of CNTs added to Ni(OH) 2 should be optimized to obtain a high-performance nickel electrode, and an optimum amount of CNT addition was found to be 3 wt.%. The superior electrochemical performance of the nickel electrode with CNTs could be attributed to lower electrochemical impedance and less γ-NiOOH formed during charge/discharge cycling, as indicated by electrochemical impedance spectroscopy and X-ray diffraction analyses. Thus, it was an effective method to improve the electrochemical properties of pasted nickel electrodes by adding an appropriate amount of CNTs to spherical Ni(OH) 2 as the active material

Carbon deposition on nickel ferrites and nickel-magnetite surfaces

International Nuclear Information System (INIS)

Allen, G.C.; Jutson, J.A.

1988-06-01

Carbon deposition on Commercial Advanced Gas-Cooled Reactor (CAGR) fuel cladding and heat exchanger surfaces lowers heat transfer efficiency and increases fuel pin temperatures. Several types of deposit have been identified including both thin dense layers and also low density columnar deposits with filamentary or convoluted laminar structure. The low-density types are often associated with particles containing iron, nickel or manganese. To identify the role of nickel in the deposition process surfaces composed of nickel-iron spinels or metallic nickel/magnetite mixtures have been exposed to γ radiation in a gas environment simulating that in the reactor. Examination of these surfaces by Scanning Electron Microscopy (SEM) and Transmission Electron Microscopy (TEM) have shown that while metallic nickel (Ni(O)) catalyses the formation of filamentary low density carbon deposits, the presence of divalent nickel (Ni(II)) sites in spinel type oxides is associated only with dense deposits. (author)

CO dissociation on Ni: The effect of steps and of nickel carbonyl

DEFF Research Database (Denmark)

Engbæk, Jakob; Lytken, Ole; Nielsen, Jane Hvolbæk

2008-01-01

The dissociation of CO was investigated on a stepped Ni(141313) crystal. The experiments show that the monoatomic steps completely dominate the dissociation of CO on the nickel surface. The activation energy for dissociation of CO along the steps is measured at 500 K to be 150 kJ/mol in the press...... and in the Fischer-Tropsch synthesis....

Mixed nickel-gallium tellurides Ni{sub 3−x}GaTe{sub 2} as a matrix for incorporating magnetic cations: A Ni{sub 3−x}Fe{sub x}GaTe{sub 2} series

Energy Technology Data Exchange (ETDEWEB)

Kuznetsov, Alexey N., E-mail: alexei@inorg.chem.msu.ru [Department of Chemistry, Lomonosov Moscow State University, Leninskie Gory 1-3, GSP-1, 119991 Moscow (Russian Federation); N.S. Kurnakov Institute of General and Inorganic Chemistry, RAS, Leninsky pr. 31, GSP-1, 119991 Moscow (Russian Federation); Stroganova, Ekaterina A.; Zakharova, Elena Yu; Solopchenko, Alexander V.; Sobolev, Alexey V.; Presniakov, Igor A. [Department of Chemistry, Lomonosov Moscow State University, Leninskie Gory 1-3, GSP-1, 119991 Moscow (Russian Federation); Kirdyankin, Denis I.; Novotortsev, Vladimir M. [N.S. Kurnakov Institute of General and Inorganic Chemistry, RAS, Leninsky pr. 31, GSP-1, 119991 Moscow (Russian Federation)

2017-06-15

Using a high-temperature ampoule technique, a series of mixed nickel-iron-gallium metal-rich tellurides with layered structures, Ni{sub 3-x}Fe{sub x}GaTe{sub 2}, were prepared and characterized based on X-ray powder diffraction, energy-dispersive spectroscopy, and {sup 57}Fe Mössbauer spectroscopy data. These compounds may be regarded as a result of partial substitution of nickel by iron in the recently reported ternary Ni{sub 3-x}GaTe{sub 2} series, which are based on NiAs/Ni{sub 2}In type of structure. The compositional boundary for the substitution was found to be at x~1. According to the Mössbauer spectroscopy data, the substitution is not statistical, and iron atoms with the increase in x tend to preferentially occupy those nickel positions that are partially vacant in the initial ternary compound. Magnetic measurements data for the Ni{sub 3-x}Fe{sub x}GaTe{sub 2} series show dramatic change in behavior from temperature-independent paramagnetic properties of the initial matrix to a low-temperature (~75 K) ferromagnetic ordering in the Ni{sub 2}FeGaTe{sub 2}. - Graphical abstract: Ordered substitution of nickel by iron in the Ni{sub 3−x}GaTe{sub 2} series leading to ferromagnetic ordering. - Highlights: • A series of Ni{sub 3−x}Fe{sub x}GaTe{sub 2} compounds were synthesized. • They adopt the NiAs/Ni{sub 2}In type of structure with ordered iron distribution. • The distribution of iron was studied using {sup 57}Fe Mössbauer spectroscopy. • An increase in iron content leads to the strong ferromagnetic coupling.

Effects of reduction temperature to Ni and Fe content and the morphology of agglomerate of reduced laterite limonitic nickel ore by coal-bed method

Science.gov (United States)

Abdul, Fakhreza; Pintowantoro, Sungging; Kawigraha, Adji; Nursidiq, Ahlidin

2018-04-01

As the current drop of nickel sulfide ore on earth, the attention to nickel laterite ore processing was inscreased in order to fulfill the future nickel demand needs. This research aims to optimized the process of nickel laterite ore extraction using coal bed method. This research was conducted by reducing low grade nickel laterite ore (limonitic) with nickel content of 1.25 %. The reduction process was carried out using CO gas which formed by the reaction of coal and dolomite. The Briquette of nickel ore, coal, Na2SO4 mixtures incorporated in the crucible with bed, then reduced for 6 hours at the temperature of 1200 °C. 1400 °C, and 1400 °C. The result of the research shown that the highest increase of Ni content and Ni recovery value was in the reduction temperature of 1400 °C with the increase of 3.44 %, and the recovery value of Ni equal to 86.75 %. While the highest increase of Fe content and Fe recovery value, respectively, was in the reduction temperature of 1300 °C with the increase of 22.67 % and 1200 °C with Fe recovery value of 89.41 %.

OXIDATIVE-REFORMING OF METHANE AND PARTIAL OXIDATION OF METHANE REACTIONS OVER NiO/PrO2/ZrO2 CATALYSTS: EFFECT OF NICKEL CONTENT

Directory of Open Access Journals (Sweden)

Y. J. O. Asencios

Full Text Available Abstract In this work the behavior of NiO-PrO2-ZrO2 catalysts containing various nickel loadings was evaluated in the partial oxidation of methane and oxidative-reforming reactions of methane. The catalysts were characterized by X-Ray Diffraction Analysis (in situ-XRD, Temperature Programmed Reduction (H2-TPR, Scanning Electron Microscopy (SEM/EDX and Adsorption-Desorption of nitrogen (BET area. The reactions were carried out at 750 °C and 1 atm for 5 hours. The catalysts were studied with different nickel content: 0, 5, 10 and 15% (related to total weight of catalyst, wt%. In both reactions, the catalyst containing the mixture of the three oxides (NiO/PrO2/ZrO2 with 15% nickel (15NiPrZr catalyst showed the best activity for the conversion of the reactants into Syngas and showed high selectivity for H2 and CO. The results suggest that the promoter PrO2 and the Niº centers are in a good proportion in the catalyst with 15% Ni. Our results showed that low nickel concentrations in the catalyst led to high metallic dispersion; however, very low nickel concentrations did not favor the methane transformation into Syngas. The catalyst containing only NiO/ZrO2 in the mixture was not sufficient for the catalysis. The presence of the promoter PrO2 was very important for the catalysis of the POM.

Hydrometallurgical recovery of metal values from sulfuric acid leaching liquor of spent lithium-ion batteries

International Nuclear Information System (INIS)

Chen, Xiangping; Chen, Yongbin; Zhou, Tao; Liu, Depei; Hu, Hang; Fan, Shaoyun

2015-01-01

Highlights: • Selective precipitation and solvent extraction were adopted. • Nickel, cobalt and lithium were selectively precipitated. • Co-D2EHPA was employed as high-efficiency extraction reagent for manganese. • High recovery percentages could be achieved for all metal values. - Abstract: Environmentally hazardous substances contained in spent Li-ion batteries, such as heavy metals and nocuous organics, will pose a threat to the environment and human health. On the other hand, the sustainable recycling of spent lithium-ion batteries may bring about environmental and economic benefits. In this study, a hydrometallurgical process was adopted for the comprehensive recovery of nickel, manganese, cobalt and lithium from sulfuric acid leaching liquor from waste cathode materials of spent lithium-ion batteries. First, nickel ions were selectively precipitated and recovered using dimethylglyoxime reagent. Recycled dimethylglyoxime could be re-used as precipitant for nickel and revealed similar precipitation performance compared with fresh dimethylglyoxime. Then the separation of manganese and cobalt was conducted by solvent extraction method using cobalt loaded D2EHPA. And McCabe–Thiele isotherm was employed for the prediction of the degree of separation and the number of extraction stages needed at specific experimental conditions. Finally, cobalt and lithium were sequentially precipitated and recovered as CoC 2 O 4 ⋅2H 2 O and Li 2 CO 3 using ammonium oxalate solution and saturated sodium carbonate solution, respectively. Recovery efficiencies could be attained as follows: 98.7% for Ni; 97.1% for Mn, 98.2% for Co and 81.0% for Li under optimized experimental conditions. This hydrometallurgical process may promise a candidate for the effective separation and recovery of metal values from the sulfuric acid leaching liquor

Hydrometallurgical recovery of metal values from sulfuric acid leaching liquor of spent lithium-ion batteries

Energy Technology Data Exchange (ETDEWEB)

Chen, Xiangping; Chen, Yongbin; Zhou, Tao, E-mail: zhoutao@csu.edu.cn; Liu, Depei; Hu, Hang; Fan, Shaoyun

2015-04-15

Highlights: • Selective precipitation and solvent extraction were adopted. • Nickel, cobalt and lithium were selectively precipitated. • Co-D2EHPA was employed as high-efficiency extraction reagent for manganese. • High recovery percentages could be achieved for all metal values. - Abstract: Environmentally hazardous substances contained in spent Li-ion batteries, such as heavy metals and nocuous organics, will pose a threat to the environment and human health. On the other hand, the sustainable recycling of spent lithium-ion batteries may bring about environmental and economic benefits. In this study, a hydrometallurgical process was adopted for the comprehensive recovery of nickel, manganese, cobalt and lithium from sulfuric acid leaching liquor from waste cathode materials of spent lithium-ion batteries. First, nickel ions were selectively precipitated and recovered using dimethylglyoxime reagent. Recycled dimethylglyoxime could be re-used as precipitant for nickel and revealed similar precipitation performance compared with fresh dimethylglyoxime. Then the separation of manganese and cobalt was conducted by solvent extraction method using cobalt loaded D2EHPA. And McCabe–Thiele isotherm was employed for the prediction of the degree of separation and the number of extraction stages needed at specific experimental conditions. Finally, cobalt and lithium were sequentially precipitated and recovered as CoC{sub 2}O{sub 4}⋅2H{sub 2}O and Li{sub 2}CO{sub 3} using ammonium oxalate solution and saturated sodium carbonate solution, respectively. Recovery efficiencies could be attained as follows: 98.7% for Ni; 97.1% for Mn, 98.2% for Co and 81.0% for Li under optimized experimental conditions. This hydrometallurgical process may promise a candidate for the effective separation and recovery of metal values from the sulfuric acid leaching liquor.

Toxicity of nickel in the marine calanoid copepod Acartia tonsa: Nickel chloride versus nanoparticles

International Nuclear Information System (INIS)

Zhou, C.; Vitiello, V.; Casals, E.; Puntes, V.F.; Iamunno, F.; Pellegrini, D.; Changwen, W.; Benvenuto, G.; Buttino, I.

2016-01-01

Highlights: • Acartia tonsa copepod is more sensitive to NiCl_2 than to nickel nanoparticles. • At the tested concentration egg production was not affected by both form of nickel. • Egg viability is the most sensitive end-point for both form of nickel. • Nickel dissolved in seawater increased with nanoparticle concentration. • Acartia tonsa adults were able to ingest nanoparticles. - Abstract: Nickel compounds are widely used in industries and have been massively introduced in the environment in different chemical forms. Here we report the effect of two different chemical forms of nickel, NiCl_2 and nickel nanoparticles (NiNPs), on the reproduction of the marine calanoid copepod Acartia tonsa. The behavior of nickel nanoparticles was analyzed with different techniques and with two protocols. In the “sonicated experiment” (SON) NiNP solution was sonicated while in the “non-sonicated experiment” (NON-SON) the solution was vigorously shaken by hand. Final nominal concentrations of 5, 10 and 50 mg L"−"1 and 1, 5 and 10 mg L"−"1 NiNPs were used for the acute and semichronic tests, respectively. Nanoparticle size did not change over time except for the highest concentration of 50 mg L"−"1 NiNPs, in which the diameter increased up to 843 nm after 48 h. The concentration of Ni dissolved in the water increased with NP concentration and was similar for SON and NON-SON solutions. Our results indicate that sonication does not modify toxicity for the copepod A. tonsa. Mean EC_5_0 values were similar for NON-SON (20.2 mg L"−"1) and SON experiments (22.14 mg L"−"1) in the acute test. Similarly, no differences occurred between the two different protocols in the semichronic test, with an EC_5_0 of 7.45 mg L"−"1 and 6.97 mg L"−"1 for NON-SON and SON experiments, respectively. Acute and semichronic tests, conducted exposing A. tonsa embryos to NiCl_2 concentrations from 0.025 to 0.63 mg L"−"1, showed EC_5_0 of 0.164 and 0.039 mg L"−"1, respectively

Nickel removal from nickel plating waste water using a biologically active moving-bed sand filter.

Science.gov (United States)

Pümpel, Thomas; Macaskie, Lynne E; Finlay, John A; Diels, Ludo; Tsezos, Marios

2003-12-01

Efficient removal of dissolved nickel was observed in a biologically active moving-bed 'MERESAFIN' sand filter treating rinsing water from an electroless nickel plating plant. Although nickel is fully soluble in this waste water, its passage through the sand filter promoted rapid removal of approximately 1 mg Ni/l. The speciation of Ni in the waste water was modelled; the most probable precipitates forming under the conditions in the filter were predicted using PHREEQC. Analyses of the Ni-containing biosludge using chemical, electron microscopical and X-ray spectroscopic techniques confirmed crystallisation of nickel phosphate as arupite (Ni3(PO4)2 x 8H2O), together with hydroxyapatite within the bacterial biofilm on the filter sand grains. Biosorption contributed less than 1% of the overall sequestered nickel. Metabolising bacteria are essential for the process; the definitive role of specific components of the mixed population is undefined but the increase in pH promoted by metabolic activity of some microbial components is likely to promote nickel desolubilisation by others.

First principles nickel-cadmium and nickel hydrogen spacecraft battery models

Energy Technology Data Exchange (ETDEWEB)

Timmerman, P.; Ratnakumar, B.V.; Distefano, S.

1996-02-01

The principles of Nickel-Cadmium and Nickel-Hydrogen spacecraft battery models are discussed. The Ni-Cd battery model includes two phase positive electrode and its predictions are very close to actual data. But the Ni-H2 battery model predictions (without the two phase positive electrode) are unacceptable even though the model is operational. Both models run on UNIX and Macintosh computers.

Extracellular synthesis and characterization of nickel oxide nanoparticles from Microbacterium sp. MRS-1 towards bioremediation of nickel electroplating industrial effluent.

Science.gov (United States)

Sathyavathi, S; Manjula, A; Rajendhran, J; Gunasekaran, P

2014-08-01

In the present study, a nickel resistant bacterium MRS-1 was isolated from nickel electroplating industrial effluent, capable of converting soluble NiSO4 into insoluble NiO nanoparticles and identified as Microbacterium sp. The formation of NiO nanoparticles in the form of pale green powder was observed on the bottom of the flask upon prolonged incubation of liquid nutrient medium containing high concentration of 2000ppm NiSO4. The properties of the produced NiO nanoparticles were characterized. NiO nanoparticles exhibited a maximum absorbance at 400nm. The NiO nanoparticles were 100-500nm in size with unique flower like structure. The elemental composition of the NiO nanoparticles was 44:39. The cells of MRS-1 were utilized for the treatment of nickel electroplating industrial effluent and showed nickel removal efficiency of 95%. Application of Microbacterium sp. MRS-1 would be a potential bacterium for bioremediation of nickel electroplating industrial waste water and simultaneous synthesis of NiO nanoparticles. Copyright © 2014 Elsevier Ltd. All rights reserved.

Effective reduction in the nanoparticle sizes of NiO obtained via the pyrolysis of nickel malonate precursor modified using oleylamine surfactant

Energy Technology Data Exchange (ETDEWEB)

Lontio Fomekong, Roussin, E-mail: lonforou@yahoo.fr [Chemistry Department, Higher Teacher Training College, University of Yaoundé I, B.P. 47, Yaoundé (Cameroon); Institut de la Matière Condensée et des Nanosciences, Université Catholique de Louvain, Croix du Sud 1, 1348 Louvain-La-Neuve (Belgium); Ngolui Lambi, John; Ebede, Guy Roland [Chemistry Department, Higher Teacher Training College, University of Yaoundé I, B.P. 47, Yaoundé (Cameroon); Kenfack Tsobnang, Patrice [Chemistry Department, University of Dschang, PO Box 96, Dschang (Cameroon); Tedjieukeng Kamta, Hypolite Mathias; Ngnintedem Yonti, Cedrik [Chemistry Department, Higher Teacher Training College, University of Yaoundé I, B.P. 47, Yaoundé (Cameroon); Delcorte, Arnaud [Institut de la Matière Condensée et des Nanosciences, Université Catholique de Louvain, Croix du Sud 1, 1348 Louvain-La-Neuve (Belgium)

2016-09-15

Nickel oxide nanoparticles were synthesized via thermal decomposition of two precursors, the first, a simple nickel malonate and the second, a nickel malonate modified by oleylamine, a surfactant, both having been synthesized by precipitation. While FTIR, TGA and ToF-SIMS were used to characterize the two precursors and to show the presence of oleylamine in the modified precursor, XRD, SEM, TEM and BET were employed to investigate the structure, the morphology and the specific surface area of the decomposition products obtained after pyrolysis. The results showed that the modification of nickel malonate by oleylamine was effective. The XRD results, which showed a cubic structure for the NiO obtained, suggest with SEM an important particle size reduction (at least 54%) when oleylamine was used to modify the nickel malonate precursor. The SEM images also showed a well-defined spherical nanoparticle morphology in both cases, not affected by the presence of oleylamine. The TEM also confirmed the reduction of particle size and their spherical nature but at the same time showed that, in the presence of oleylamine, there was no agglomeration resulting in a more uniform particle size distribution. The specific surface area of the NiO obtained by the oleylamine-modified precursor was 4.7 times larger than that obtained with the regular precursor. This again confirms the particle size reduction. - Highlights: • Nickel malonate precursor has been synthesized by precipitation method. • This precursor was successfully modified by a surfactant (oleylamine). • NiO was identified as the decomposition products of the previous precursors. • Oleylamine has provoked around 54% of particle size reduction of the NiO.

Sintering of nickel steam reforming catalysts

DEFF Research Database (Denmark)

Sehested, Jens; Larsen, Niels Wessel; Falsig, Hanne

2014-01-01

. In this paper, particle migration and coalescence in nickel steam reforming catalysts is studied. Density functional theory calculations indicate that Ni-OH dominate nickel transport at nickel surfaces in the presence of steam and hydrogen as Ni-OH has the lowest combined energies of formation and diffusion...

The Ce-Ni-Si system as a representative of the rare earth-Ni-Si family: Isothermal section and new rare-earth nickel silicides

Energy Technology Data Exchange (ETDEWEB)

Morozkin, A.V., E-mail: morozkin@tech.chem.msu.ru [Department of Chemistry, Moscow State University, Leninskie Gory, House 1, Building 3, Moscow, GSP-1, 119991 (Russian Federation); Knotko, A.V.; Garshev, A.V. [Department of Chemistry, Moscow State University, Leninskie Gory, House 1, Building 3, Moscow, GSP-1, 119991 (Russian Federation); Faculty of Materials Science, Moscow State University, Leninskie Gory, House 1, Building 73, Moscow, GSP-1, 119991 (Russian Federation); Yapaskurt, V.O. [Department of Petrology, Geological Faculty Moscow State University, Leninskie Gory, Moscow 119991 (Russian Federation); Nirmala, R. [Indian Institute of Technology Madras, Chennai 600036 (India); Quezado, S.; Malik, S.K. [Departamento de Física Teórica e Experimental, Universidade Federal do Rio Grande do Norte, Natal, 59082-970 (Brazil)

2016-11-15

Si{sub 2}; while no appreciable solubility was observed for the other binary compounds of the Ce-Ni-Si system. As a prolongation of Rare Earth-Ni-Si system’s isostructural rows, LaNi{sub 7}Si{sub 6} and YNi{sub 6.6}Si{sub 6.1} (GdNi{sub 7}Si{sub 6}-type), ScNi{sub 6}Si{sub 6} (YCo{sub 6}Ge{sub 6}-type), NdNi{sub 6}Si{sub 6} (YNi{sub 6}Si{sub 6}-type), (Tb, Ho){sub 2}Ni{sub 15}Si{sub 2} (Th{sub 2}Zn{sub 17}-type), Nd{sub 2}Ni{sub 2.3}Si{sub 0.7} and Sm{sub 2}Ni{sub 2.2}Si{sub 0.8} (Mo{sub 2}NiB{sub 2}-type), Nd{sub 3}Ni{sub 2.55}Si{sub 1.45} (W{sub 3}CoB{sub 3}-type) and (Tb, Dy){sub 7}Ni{sub 50}Si{sub 19} (Y{sub 7}Ni{sub 49}Si{sub 20}-type) compounds were synthesized and investigated. Magnetic properties of the CeNi{sub 6}Si{sub 6}, CeNi{sub 7}Si{sub 6}, CeNi{sub 8.8}Si{sub 4.2}, Ce{sub 6}Ni{sub 7}Si{sub 4}, CeNi{sub 5}Si, Ce{sub 2}Ni{sub 2.5}Si{sub 0.5}, Nd{sub 2}Ni{sub 2.3}Si{sub 0.7} and Dy{sub 7}Ni{sub 50}Si{sub 19} compounds have also been investigated and are presented here. - Highlights: • Ce-Ni-Si isothermal section was obtained at 870/1070 K. • Twenty one known ternary cerium nickel silicides were confirmed in Ce-Ni-Si. • Five new cerium nickel silicides were detected in Ce-Ni-Si. • Eleven new rare earth nickel silicides were detected in R-Ni-Si. • Magnetic properties of eight rare earth nickel silicides were investigated.

Separation and Precipitation of Nickel from Acidic Sulfate Leaching Solution of Molybdenum-Nickel Black Shale by Potassium Nickel Sulfate Hexahydrate Crystallization

Science.gov (United States)

Deng, Zhigan; Wei, Chang; Fan, Gang; Li, Xingbin; Li, Minting; Li, Cunxiong

2018-02-01

Nickel was separated and precipitated with potassium nickel sulfate hexahydrate [K2Ni(SO4)2·6H2O] from acidic sulfate solution, a leach solution from molybdenum-nickel black shale. The effects of the potassium sulfate (K2SO4) concentration, crystallization temperature, solution pH, and crystallization time on nickel(II) recovery and iron(III) precipitation were investigated, revealing that nickel and iron were separated effectively. The optimum parameters were K2SO4 concentration of 200 g/L, crystallization temperature of 10°C, solution pH of 0.5, and crystallization time of 24 h. Under these conditions, 97.6% nickel(II) was recovered as K2Ni(SO4)2·6H2O crystals while only 2.0% of the total iron(III) was precipitated. After recrystallization, 98.4% pure K2Ni(SO4)2·6H2O crystals were obtained in the solids. The mother liquor was purified by hydrolysis-precipitation followed by cooling, and more than 99.0% K2SO4 could be crystallized. A process flowsheet was developed to separate iron(III) and nickel(II) from acidic-sulfate solution.

Preparation and characterization of 6-layered functionally graded nickel-alumina (Ni-Al2O3) composites

Science.gov (United States)

Latiff, M. I. A.; Nuruzzaman, D. M.; Basri, S.; Ismail, N. M.; Jamaludin, S. N. S.; Kamaruzaman, F. F.

2018-04-01

The present research study deals with the preparation of 6-layered functionally graded (FG) metal-ceramic composite materials through powder metallurgy technique. Using a cylindrical die-punch set made of steel, the nickel-alumina (Ni-Al2O3) graded composite structure was fabricated. The samples consist of four gradual inter layers of varied nickel composition (80wt.%, 60wt.%, 40wt.%, 20wt.%) sandwiched with pure Ni and Al2O3 powders at the ends (100wt.% and 0wt.% nickel) were fabricated under 30 ton compaction load using a hydraulic press. After that, two-step sintering was carried out at sintering temperature 1200ºC and soaking time 3 hours was maintained in a tube furnace. The properties of the prepared samples were characterized by radial shrinkage, optical microscopy and hardness testing. Results showed that larger shrinkage occurred within the ceramic phase which proves that more porosities were eliminated in the ceramic rich layers. From the microstructural analysis, it was observed that alumina particles are almost uniformly distributed in nickel matrix, so as nickel particles in the ceramic matrix of alumina-dominant layers. From interfacial analyses, it was observed that a smooth transition in microstructure from one layer to the next confirms a good interfacial solid state bonding between metal-ceramic constituents and good compaction process. On the other hand, microhardness test results suggest that there might be increasing percentage of porosities in the graded structure as the ceramic content rises.

The potential use of indigenous nickel hyperaccumulators for small-scale mining in The Philippines

Directory of Open Access Journals (Sweden)

E S Fernando

2013-10-01

Full Text Available Uptake of nickel and three other heavy metals (copper, cobalt, and chromium was examined in 33 species of the common and rare native vascular plants growing in an ultramafic area currently subjected to mining in Zambales Province, Luzon, Philippines. Leaf tissue samples were initially screened in the field using filter paper impregnated with dimethylglyoxime (1% solution in 70% ethyl alcohol and later analyzed by atomic absorption spectroscopy. One species was found to be a hypernickelophore (>10,000 µg/g, eight species were nickel hyperaccumulators (>1,000 µg/g, nineteen species were hemi-accumulators (>100-1,000 µg/g, and five species were non-accumulators (<100 µg/g. This paper significantly adds to the list of hyperaccumulator species first reported for the Philippines in 1992. The findings will be discussed in context of using indigenous species for post mining ecological restoration and nickel phytoextraction in small-scale mining in the Philippines

Nickel silicide formation in silicon implanted nickel

Science.gov (United States)

Rao, Z.; Williams, J. S.; Pogany, A. P.; Sood, D. K.; Collins, G. A.

1995-04-01

Nickel silicide formation during the annealing of very high dose (≥4.5×1017 ions/cm2) Si implanted Ni has been investigated, using ion beam analytical techniques, electron microscopy, and x-ray diffraction analysis. An initial amorphous Si-Ni alloy, formed as a result of high dose ion implantation, first crystallized to Ni2Si upon annealing in the temperature region of 200-300 °C. This was followed by the formation of Ni5Si2 in the temperature region of 300-400 °C and then by Ni3Si at 400-600 °C. The Ni3Si layer was found to have an epitaxial relationship with the substrate Ni, which was determined as Ni3Si∥Ni and Ni3Si∥Ni for Ni(100) samples. The minimum channeling yield in the 2 MeV He Rutherford backscattering and channeling spectra of this epitaxial layer improved with higher annealing temperatures up to 600 °C, and reached a best value measured at about 8%. However, the epitaxial Ni3Si dissolved after long time annealing at 600 °C or annealing at higher temperatures to liberate soluble Si into the Ni substrate. The epitaxy is attributed to the excellent lattice match between the Ni3Si and the Ni. The annealing behavior follows the predictions of the Ni-Si phase diagram for this nickel-rich binary system.

Electroplating condition for Ni nanocrystalline on metal (Ni and Cu) plates

Energy Technology Data Exchange (ETDEWEB)

Park, Keun Yung; Uhm, Young Rang; Son, Kwang Jae; Shim, Young Ho; Choi, Sun Ju [KAERI, Daejeon (Korea, Republic of)

2012-10-15

Ni 63, a beta radiation source, is prepared by the electrical deposition of radioactive Ni 63 ions on a thin non radioactive nickel foil or Cu plate. Given a half life of 100 years, a nuclear battery will still produce half of its initial starting power after 100 years. A speck of a radioisotope like nickel 63, for example, contains enough energy to power a nano nuclear battery for decades, and to do so safely. Ni 63 plating is similar to other electroplating processes that employ soluble metal anodes. It requires the passage of a direct current between two electrodes that are immersed in a conductive, aqueous solution of nickel salts. The charged Ni ions are formed by sulfate, sulfamate, chloride, and a Watts bath. However, the charged Ni 63 ions are formed by dissolving metal Ni 63. To established the coating condition of Ni 63, non radioactive metal Ni particles are dissolved an acid solution and electroplated on a Ni sheet. The nickel plating process is used extensively for decorative, engineering and electro forming purposes because the appearance and other properties of electrodeposited nickel can be varied over a wide range by controlling the composition and operating parameters of the plating solution. A continuous increase in the grain size versus current density has also been recognized in the direct current electrodeposition of nickel coating. On the other hand, A runa et al. reported that the current density has no significant effect on the grain size of nickel electro deposits. A review of the literature shows that saccharin has often been added to a nickel plating bath since the 1980s to improve the ductility and brightness, and in later periods as a grain refiner agent. In the present paper, not only the preparation of a Ni plating solution prepared by dissolving metal particles, but also an optimization of the deposition conditions, such as the current density, saccharin concentration in the bath, and different metal substrates were investigated

Electroplating condition for Ni nanocrystalline on metal (Ni and Cu) plates

International Nuclear Information System (INIS)

Park, Keun Yung; Uhm, Young Rang; Son, Kwang Jae; Shim, Young Ho; Choi, Sun Ju

2012-01-01

Ni 63, a beta radiation source, is prepared by the electrical deposition of radioactive Ni 63 ions on a thin non radioactive nickel foil or Cu plate. Given a half life of 100 years, a nuclear battery will still produce half of its initial starting power after 100 years. A speck of a radioisotope like nickel 63, for example, contains enough energy to power a nano nuclear battery for decades, and to do so safely. Ni 63 plating is similar to other electroplating processes that employ soluble metal anodes. It requires the passage of a direct current between two electrodes that are immersed in a conductive, aqueous solution of nickel salts. The charged Ni ions are formed by sulfate, sulfamate, chloride, and a Watts bath. However, the charged Ni 63 ions are formed by dissolving metal Ni 63. To established the coating condition of Ni 63, non radioactive metal Ni particles are dissolved an acid solution and electroplated on a Ni sheet. The nickel plating process is used extensively for decorative, engineering and electro forming purposes because the appearance and other properties of electrodeposited nickel can be varied over a wide range by controlling the composition and operating parameters of the plating solution. A continuous increase in the grain size versus current density has also been recognized in the direct current electrodeposition of nickel coating. On the other hand, A runa et al. reported that the current density has no significant effect on the grain size of nickel electro deposits. A review of the literature shows that saccharin has often been added to a nickel plating bath since the 1980s to improve the ductility and brightness, and in later periods as a grain refiner agent. In the present paper, not only the preparation of a Ni plating solution prepared by dissolving metal particles, but also an optimization of the deposition conditions, such as the current density, saccharin concentration in the bath, and different metal substrates were investigated

Ni/SiO2 Catalyst Prepared with Nickel Nitrate Precursor for Combination of CO2 Reforming and Partial Oxidation of Methane: Characterization and Deactivation Mechanism Investigation

Directory of Open Access Journals (Sweden)

Sufang He

2015-01-01

Full Text Available The performance of Ni/SiO2 catalyst in the process of combination of CO2 reforming and partial oxidation of methane to produce syngas was studied. The Ni/SiO2 catalysts were prepared by using incipient wetness impregnation method with nickel nitrate as a precursor and characterized by FT-IR, TG-DTA, UV-Raman, XRD, TEM, and H2-TPR. The metal nickel particles with the average size of 37.5 nm were highly dispersed over the catalyst, while the interaction between nickel particles and SiO2 support is relatively weak. The weak NiO-SiO2 interaction disappeared after repeating oxidation-reduction-oxidation in the fluidized bed reactor at 700°C, which resulted in the sintering of metal nickel particles. As a result, a rapid deactivation of the Ni/SiO2 catalysts was observed in 2.5 h reaction on stream.

Toxicity of nickel in the marine calanoid copepod Acartia tonsa: Nickel chloride versus nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Zhou, C. [Istituto per la Protezione e Ricerca Ambientale ISPRA-STS Livorno, Piazzale dei marmi 12, 57123 Livorno (Italy); Academic Centre for Innovation and Development in the Food Industry (CAISIAL), Università degli Studi di Napoli Federico II, 80055 Portici (Italy); Vitiello, V. [Istituto per la Protezione e Ricerca Ambientale ISPRA-STS Livorno, Piazzale dei marmi 12, 57123 Livorno (Italy); Casals, E. [Institut Català de Nanotecnologia, Campus de la Universitat Autònoma de Barcelone, 08193 Bellaterra (Spain); Puntes, V.F. [Institut Català de Nanotecnologia, Campus de la Universitat Autònoma de Barcelone, 08193 Bellaterra (Spain); Institut Català de Recerca i Estudis Avançats (ICREA), Passeig Lluís Companys, 23, 08010 Barcelona (Spain); Iamunno, F. [Stazione Zoologica Anton Dohrn, Villa Comunale, Napoli (Italy); Pellegrini, D. [Istituto per la Protezione e Ricerca Ambientale ISPRA-STS Livorno, Piazzale dei marmi 12, 57123 Livorno (Italy); Changwen, W. [Zhejiang Ocean University, 1 Rd. South Haida, Lincheng New Area, Dinghai District Zhoushan City, 316022 (China); Benvenuto, G. [Stazione Zoologica Anton Dohrn, Villa Comunale, Napoli (Italy); Buttino, I., E-mail: isabella.buttino@isprambiente.it [Istituto per la Protezione e Ricerca Ambientale ISPRA-STS Livorno, Piazzale dei marmi 12, 57123 Livorno (Italy)

2016-01-15

Highlights: • Acartia tonsa copepod is more sensitive to NiCl{sub 2} than to nickel nanoparticles. • At the tested concentration egg production was not affected by both form of nickel. • Egg viability is the most sensitive end-point for both form of nickel. • Nickel dissolved in seawater increased with nanoparticle concentration. • Acartia tonsa adults were able to ingest nanoparticles. - Abstract: Nickel compounds are widely used in industries and have been massively introduced in the environment in different chemical forms. Here we report the effect of two different chemical forms of nickel, NiCl{sub 2} and nickel nanoparticles (NiNPs), on the reproduction of the marine calanoid copepod Acartia tonsa. The behavior of nickel nanoparticles was analyzed with different techniques and with two protocols. In the “sonicated experiment” (SON) NiNP solution was sonicated while in the “non-sonicated experiment” (NON-SON) the solution was vigorously shaken by hand. Final nominal concentrations of 5, 10 and 50 mg L{sup −1} and 1, 5 and 10 mg L{sup −1} NiNPs were used for the acute and semichronic tests, respectively. Nanoparticle size did not change over time except for the highest concentration of 50 mg L{sup −1} NiNPs, in which the diameter increased up to 843 nm after 48 h. The concentration of Ni dissolved in the water increased with NP concentration and was similar for SON and NON-SON solutions. Our results indicate that sonication does not modify toxicity for the copepod A. tonsa. Mean EC{sub 50} values were similar for NON-SON (20.2 mg L{sup −1}) and SON experiments (22.14 mg L{sup −1}) in the acute test. Similarly, no differences occurred between the two different protocols in the semichronic test, with an EC{sub 50} of 7.45 mg L{sup −1} and 6.97 mg L{sup −1} for NON-SON and SON experiments, respectively. Acute and semichronic tests, conducted exposing A. tonsa embryos to NiCl{sub 2} concentrations from 0.025 to 0.63 mg L{sup −1

Tuning crystal phase of NiS_x through electro-oxidized nickel foam: A novel route for preparing efficient electrocatalysts for oxygen evolution reaction

International Nuclear Information System (INIS)

Li, Xiao; Shang, Xiao; Rao, Yi; Dong, Bin; Han, Guan-Qun; Hu, Wen-Hui; Liu, Yan-Ru; Yan, Kai-Li; Chi, Jing-Qi; Chai, Yong-Ming; Liu, Chen-Guang

2017-01-01

Highlights: • Electro-oxidized nickel foam as a support has been used to prepare NiS_x phases. • Ni(OH)_2 layer on electro-oxidized NF is responsible for the growth of β-NiS. • NiS_x/NF(Ox) composed of β-NiS and Ni_3S_2 has enhanced electrocatalytic activity. • The growth mechanisms of mixed NiS_x phases of NiS_x/NF(Ox) have been discussed. - Abstract: A facile solvothermal sulfurization using electro-oxidized nickel foam (NF(Ox)) as support has been applied to prepare NiS_x/NF(Ox) electrocatalyst with highly efficient activity for oxygen evolution reaction (OER). XRD patterns confirm the composition of NiS_x/NF(Ox): two kinds of crystal phase including β-NiS and Ni_3S_2. While using bare NF as support under identical conditions, only Ni_3S_2 phase can be detected. SEM images reveal two kinds of morphologies of NiS_x/NF(Ox) including pyramids structure of β-NiS and nanorod-like structure of Ni_3S_2, which implies the tuning effect of electro-pretreatment of NF on the selective preparation of NiS_x crystal phase. It can be speculated that Ni(OH)_2 layer derived from electro-oxidized NF is responsible for the growth of β-NiS while metallic Ni is transformed into Ni_2S_3 during sulfurization. Electrochemical measurements for OER indicate the enhanced electrocatalytic activity of NiS_x/NF(Ox) with a small overpotential of 72 mV to reach 10 mA cm"−"2 compared with Ni_3S_2/NF, which may be ascribed to the improved electron-transfer kinetics relating to the unique atomic configurations and crystalline structures of β-NiS. The electro-oxidation pretreatment of nickel foam provides a simple and convenient method by tuning different NiS_x crystal phases for preparing excellent OER eletrocatalysts.

Comparison of nickel and chromium ions released from stainless steel and NiTi wires after immersion in Oral B®, Orthokin® and artificial saliva.

Science.gov (United States)

Jamilian, Abdolreza; Moghaddas, Omid; Toopchi, Shabnam; Perillo, Letizia

2014-07-01

Oral environment of the mouth is a suitable place for biodegradation of alloys used in orthodontic wires. The toxicity of these alloys namely nickel and chromium has concerned the researchers about the release of these ions from orthodontic wires and brackets. The aim of this study was to measure the levels of nickel and chromium ions released from 0.018" stainless steel (SS) and NiTi wires after immersion in three solutions. One hundred and forty-four round NiTi and 144 round SS archwires with the diameters of 0.018" were immersed in Oral B®, Orthokin® and artificial saliva. The amounts of nickel and chromium ions released were measured after 1, 6, 24 hours and 7 days. Two way repeated ANOVA showed that the amount of chromium and nickel significantly increased in all solutions during all time intervals (p nickel ions were released more in NiTi wire in all solutions compared with SS wire. The lowest increase rate was also seen in artificial saliva. There is general consensus in literature that even very little amounts of nickel and chromium are dangerous for human body specially when absorbed orally; therefore, knowing the precise amount of these ions released from different wires when immersed in different mouthwashes is of high priority.

Properties of Ni^+ from microwave spectroscopy of n=9 Rydberg levels of Nickel

Science.gov (United States)

Woods, Shannon; Keele, Julie; Smith, Chris; Lundeen, Stephen

2012-06-01

The microwave/RESIS method was used to determine the relative positions of 15 of the n=9 Rydberg levels of Nickel with L >= 6. Because the ground state of the Ni^+ ion is a ^2D5/2 level, each Rydberg level (n,L) splits into six eigenstates whose relative positions are determined by long-range e-Ni^+ interactions present in addition to the dominant Coulomb interaction. A previous study with the optical RESIS method determined these positions with precision of +/- 30 MHz [1]. Using the microwave/RESIS method improves that precision by a factor of 300, and leads to much improved determinations of the Ni+ properties that control the long-range interactions. [4pt] [1] Julie A. Keele, Shannon L. Woods, M.E. Hanni, and S.R. Lundeen Phys. Rev. 81, 022506 (2010)

Alloys of nickel-iron and nickel-silicon do not swell under fast neutron irradiation

International Nuclear Information System (INIS)

Silvestre, G.; Silvent, A.; Regnard, C.; Sainfort, G.

1975-01-01

This research is concerned with the effect of fast-neutron irradiation on the swelling of nickel and nickel alloys. Ni-Fe (0-60at%Fe) and Ni-Si (0-8at%Si) were studied, and the fluences were in the range 10 20 -4.3x10 22 n/cm 2 . In dilute alloys, the added elements are dissolved and reduce swelling, silicon being particularly effective. In more concentrated alloys, irradiation of Ni-Fe and Ni-Si alloys brings about the formation of plate-shaped precipitates of Ni 3 X and these alloys do not swell. (Auth.)

Electron transfer behaviour of single-walled carbon nanotubes electro-decorated with nickel and nickel oxide layers

Energy Technology Data Exchange (ETDEWEB)

Adekunle, Abolanle S.; Ozoemena, Kenneth I. [Department of Chemistry, University of Pretoria, Pretoria 0002 (South Africa)

2008-08-01

The electron transfer behaviour of nickel film-decorated single-walled carbon nanotubes (SWCNTs-Ni) at edge plane pyrolytic graphite electrodes (EPPGEs) was investigated. The impact of SWCNTs on the redox properties of the nickel film was investigated with cyclic voltammetry and electrochemical impedance spectroscopy (EIS). From EIS data, obtained using ferrocyanide/ferricyanide as a redox probe, we show that the electrodes based on nickel and nickel oxide films follow electrical equivalent circuit models typical of partial charge transfer or adsorption-controlled kinetics, resembling the 'electrolyte-insulator-semiconductor sensors (EIS)'. From the models, we prove that EPPGE-SWCNT-Ni exhibits the least resistance to charge transport compared to other electrodes (approximately 30 times faster than the EPPGE-SWCNT-NiO, 25 times faster than EPPGE-SWCNT, and over 300 times faster than the bare EPPGE) suggesting the ability of the SWCNTs to act as efficient conducting species that facilitate electron transport of the integrated nickel and nickel oxide particles. (author)

Structure of Ni-rich Ni--Cr--B--Si coating alloys

International Nuclear Information System (INIS)

Knotek, O.; Lugscheider, E.; Reimann, H.

1975-01-01

The structures of quaternary, nickel-rich Ni--Cr--B--Si alloys were analyzed at a constant boron content of 10 at. percent and a temperature of 850 0 C. The composition range for silicide formation was determined. In these quaternary alloys, known binary nickel silicides, nickel and chromium borides, and the ternary silico-boride Ni 6 Si 2 B were confirmed. A new composition for the W 5 Si 3 -type phase in the Ni--B--Si system was proposed. (U.S.)

The biological importance of nickel in the food chain

Energy Technology Data Exchange (ETDEWEB)

Anke, M [Friedrich Schiller Univ., Jena (Germany). Inst. of Nutrition and Environment; Angelow, L [Friedrich Schiller Univ., Jena (Germany). Inst. of Nutrition and Environment; Glei, M [Friedrich Schiller Univ., Jena (Germany). Inst. of Nutrition and Environment; Mueller, M [Friedrich Schiller Univ., Jena (Germany). Inst. of Nutrition and Environment; Illing, H [Friedrich Schiller Univ., Jena (Germany). Inst. of Nutrition and Environment

1995-05-01

The ultra trace element nickel (Ni) is both essential and toxic for animals and humans. A Ni-poor nutrition of < 0.1 mg/kg dry matter led to Ni deficiency symptoms. Ni is a component of the urease and it is also essential for several species of bacteria which occur in the rumen of ruminants. Ni deficiency symptoms, however, have not yet been found in animals and humans since the Ni offer exceeds the Ni requirement. On the other hand, an external Ni exposure to nickel alloys induces Ni dermatitis in 8 to 14% of nickel-sensitive women and in > 1% of men after the filling of the Ni depot in the body. Experiments with 4 animal species showed that Ni exposure leads to disturbances in the Mg and above all in the Zn metabolism. Ni excess induces Zn deficiency symptoms which are similar to parakeratosis in pigs. They correspond to the symptoms of nickel allergy in humans. Therefore, the Ni intake of humans, which leads to the gradual filling of the Ni pool in the body and which can then induce nickel dermatitis in Ni-sensitive women and men, is of particular importance. The Ni requirement of adults does not exceed 25 to 35 {mu}g/day. The Ni balance of men and women was positive (+ 20%) and shows the Ni incorporation even in the case of a Ni consumption which exceeds by far the requirement. (orig.)

[Nickel levels in female dermatological patients].

Science.gov (United States)

Schwegler, U; Twardella, D; Fedorov, M; Darsow, U; Schaller, K-H; Habernegg, R; Behrendt, H; Fromme, H

2009-07-01

Nickel levels in urine were determined among 163 female dermatological patients aged 18 to 46 years. Data on life-style factors were collected in parallel via a questionnaire. Urinary nickel excretion was in the normal range of the German female population (0.2-46.1 microg Ni/g creatinine). The 95th percentile (3.9 microg Ni/l urine) exceeded the German reference value (3.0 microg Ni/l urine). In the multivariate regression analyses we found a statistically significant increase of ln-transformed nickel levels with increase in age and in women using dietary supplements. The following variables were not associated with Nickel urine levels: suffering from nickel eczema, smoking, drinking stagnated water, eating foods with high nickel contents and using nickel-containing kitchen utensils as, for example, an electric kettle with an open heater coil. We conclude that personal urinary levels should be assessed with simultaneous consideration of habits and life-style factors. A German national survery would be useful. Those patients who experience the exacerbation of their eczema in cases of oral provocation, for example, by a high nickel diet should be aware of potential sources of nickel, such as supplements.

Ni(0-CMC-Na Nickel Colloids in Sodium Carboxymethyl-Cellulose: Catalytic Evaluation in Hydrogenation Reactions

Directory of Open Access Journals (Sweden)

Abdallah Karim

2011-01-01

Full Text Available A recyclable catalyst, Ni(0-CMC-Na, composed of nickel colloids dispersed in a water soluble bioorganic polymer, sodium carboxymethylcellulose (CMC-Na, was synthesized by a simple procedure from readily available reagents. The catalyst thus obtained is stable and highly active in alkene hydrogenations.

Calculation of the driving force for the radiation induced precipitation of Ni3Si in nickel-silicon alloys

International Nuclear Information System (INIS)

Miodownik, A.P.; Watkin, J.S.

1979-01-01

The appearance of precipitates which have been identified as Ni 3 Si in irradiated stainless steels and nickel rich alloys such as Inconel is of considerable interest in relation to the swelling behaviour of such materials. Work on binary nickel-silicon alloys has shown that Ni 3 Si can be induced to precipitate in alloys whose silicon content is well below the accepted solubility limit, and it has also been shown that such precipitates redissolve when heat-treatment is continued at the same temperature in the absence of irradiation. Such effects imply an irradiation induced shift of chemical potential, and cannot be explained by merely involving accelerated diffusion. This paper represents an attempt to calculate the shift in chemical potential required to precipitate Ni 3 Si in alloys containing 1-10% Si (at%) over a range of temperatures (300-1000K), and then proceeds to relate this calculated chemical potential with available information concerning the dose rates required to induce such precipitates at various temperatures. Presentation of the results is modelled on the well established methods for handling the Time-Temperature-Transformation behaviour of ordinary alloy systems, with dose rate being substituted for the time axis. Analogous calculations are presented for nickel-germanium alloys, in order to check whether the numerical values deduced from the nickel silicon system have more general applicability, and also to see whether there are any significant differences in a system where the size factor of the solute is of the opposite sign. (orig.) [de

In situ Ni-doping during cathodic electrodeposition of hematite for excellent photoelectrochemical performance of nanostructured nickel oxide-hematite p-n junction photoanode

Science.gov (United States)

Phuan, Yi Wen; Ibrahim, Elyas; Chong, Meng Nan; Zhu, Tao; Lee, Byeong-Kyu; Ocon, Joey D.; Chan, Eng Seng

2017-01-01

Nanostructured nickel oxide-hematite (NiO/α-Fe2O3) p-n junction photoanodes synthesized from in situ doping of nickel (Ni) during cathodic electrodeposition of hematite were successfully demonstrated. A postulation model was proposed to explain the fundamental mechanism of Ni2+ ions involved, and the eventual formation of NiO on the subsurface region of hematite that enhanced the potential photoelectrochemical water oxidation process. Through this study, it was found that the measured photocurrent densities of the Ni-doped hematite photoanodes were highly dependent on the concentrations of Ni dopant used. The optimum Ni dopant at 25 M% demonstrated an excellent photoelectrochemical performance of 7-folds enhancement as compared to bare hematite photoanode. This was attributed to the increased electron donor density through the p-n junction and thus lowering the energetic barrier for water oxidation activity at the optimum Ni dopant concentration. Concurrently, the in situ Ni-doping of hematite has also lowered the photogenerated charge carrier transfer resistance as measured using the electrochemical impedance spectroscopy. It is expected that the fundamental understanding gained through this study is helpful for the rational design and construction of highly efficient photoanodes for application in photoelectrochemical process.

Carbon-encapsulated nickel-iron nanoparticles supported on nickel foam as a catalyst electrode for urea electrolysis

International Nuclear Information System (INIS)

Wu, Mao-Sung; Jao, Chi-Yu; Chuang, Farn-Yih; Chen, Fang-Yi

2017-01-01

Highlights: • Electrochemical process can purify the urea-rich wastewater, producing hydrogen gas. • Carbon-encapsulated nickel iron nanoparticles (CE-NiFe) are prepared by pyrolysis. • An ultra-thin layer of CE-NiFe nanoparticles is attached to the 3D Ni foam. • CE-NiFe nanoparticles escalate both the urea electrolysis and hydrogen evolution. - Abstract: A cyanide-bridged bimetallic coordination polymer, nickel hexacyanoferrate, could be pyrolyzed to form carbon-encapsulated nickel-iron (CE-NiFe) nanoparticles. The formation of nitrogen-doped spherical carbon shell with ordered mesoporous structure prevented the structural damage of catalyst cores and allowed the migration and diffusion of electrolyte into the hollow carbon spheres. An ultra-thin layer of CE-NiFe nanoparticles could be tightly attached to the three-dimensional macroporous nickel foam (NF) by electrophoretic deposition. The CE-NiFe nanoparticles could lower the onset potential and increase the current density in anodic urea electrolysis and cathodic hydrogen production as compared with bare NF. Macroporous NF substrate was very useful for the urea electrolysis and hydrogen production, which allowed for fast transport of electron, electrolyte, and gas products. The superior electrocatalytic ability of CE-NiFe/NF electrode in urea oxidation and water reduction made it favorable for versatile applications such as water treatment, hydrogen generation, and fuel cells.

Hydrometallurgical separation of rare earth elements, cobalt and nickel from spent nickel-metal-hydride batteries

Science.gov (United States)

Rodrigues, Luiz Eduardo Oliveira Carmo; Mansur, Marcelo Borges

The separation of rare earth elements, cobalt and nickel from NiMH battery residues is evaluated in this paper. Analysis of the internal content of the NiMH batteries shows that nickel is the main metal present in the residue (around 50% in weight), as well as potassium (2.2-10.9%), cobalt (5.1-5.5%), rare earth elements (15.3-29.0%) and cadmium (2.8%). The presence of cadmium reveals that some Ni-Cd batteries are possibly labeled as NiMH ones. The leaching of nickel and cobalt from the NiMH battery powder with sulfuric acid is efficient; operating variables temperature and concentration of H 2O 2 has no significant effect for the conditions studied. A mixture of rare earth elements is separated by precipitation with NaOH. Finally, solvent extraction with D2EHPA (di-2-ethylhexyl phosphoric acid) followed by Cyanex 272 (bis-2,4,4-trimethylpentyl phosphinic acid) can separate cadmium, cobalt and nickel from the leach liquor. The effect of the main operating variables of both leaching and solvent extraction steps are discussed aiming to maximize metal separation for recycling purposes.

Synthesis and Characterization of Chloridobis(dimethylglyoximato4-(2-ferrocenylvinylpyridinecobalt(III: A New Heterobinuclear Cobaloxime

Directory of Open Access Journals (Sweden)

Sebastián Pizarro

2016-01-01

Full Text Available The synthesis of a new heterobinuclear cobaloxime with 4-(2-ferrocenylvinylpyridine, fcvpy, is reported. The complex [CoCl(dmgH2(fcvpy], where dmgH2 is dimethylglyoxime and dmgH is dimethylglyoximato, has been characterized by 1H-NMR, UV-Vis, cyclic voltammetry, and elemental analysis. The cyclic voltammogram of this complex shows a fc/fc+ reversible wave at +0.58 V versus Ag/AgCl, one irreversible wave, Epc = −0.54 V versus Ag/AgCl, assigned to the reduction of Co(III to Co(II, and two quasireversible processes at −1.02 V and −1.10 V versus Ag/AgCl associated with the reduction of Co(II. The complex showed ferrocene-ligand charge transfer bands at 334 nm and 505 nm. TDDFT/B3LYP/6-31G(d calculations support this assignation.

Electrical and magnetic behavior of iron doped nickel titanate (Fe{sup 3+}/NiTiO{sub 3}) magnetic nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Lenin, Nayagam; Karthik, Arumugam; Sridharpanday, Mathu; Selvam, Mohanraj; Srither, Saturappan Ravisekaran; Arunmetha, Sundarmoorthy; Paramasivam, Palanisamy; Rajendran, Venkatachalam, E-mail: veerajendran@gmail.com

2016-01-01

Iron doped nickel titanate (Fe{sup 3+}/NiTiO{sub 3}) ferromagnetic nanoparticles with different concentrations of Fe (0.2, 0.4, and 0.6 mol) were synthesized using precipitation route with precursor source such as nickel nitrate and iron nitrate solutions. The prepared magnetic nanopowders were investigated through X-ray diffraction (XRD), Fourier transform infrared, scanning electron microscope, X-ray fluorescence, Brunauer–Emmett–Teller, vibrating sample magnetometer, and electrochemical impedance spectroscopy to explore the structural, ferromagnetic, and dielectric properties. The obtained XRD pattern shows formation of iron doped nickel titanate in orthorhombic structure. The crystallite size ranges from 57 to 21 nm and specific surface area ranges from 11 to 137 m{sup 2} g{sup −1}. The hysteresis loops of nanomagnetic materials show ferromagnetic behavior with higher magnitude of coercivity (H{sub c}) 867–462 Oe. The impedance analysis of ferromagnetic materials explores the ferro-dielectric behavior with enhanced properties of Fe{sup 3+}/NiTiO{sub 3} nanoparticles at higher Fe content. - Highlights: • Iron doped nickel titanate magnetic nanoparticles. • Ferromagnetic magnetism behavior with higher magnitude of coercivity. • Dielectric behavior of ferromagnetic nanoparticles with increase of Fe content.

A Ni-P@NiCo LDH core-shell nanorod-decorated nickel foam with enhanced areal specific capacitance for high-performance supercapacitors.

Science.gov (United States)

Xing, Jiale; Du, Jing; Zhang, Xuan; Shao, Yubo; Zhang, Ting; Xu, Cailing

2017-08-14

Recently, transition metal-based nanomaterials have played a key role in the applications of supercapacitors. In this study, nickel phosphide (Ni-P) was simply combined with NiCo LDH via facile phosphorization of Ni foam and subsequent electrodeposition to form core-shell nanorod arrays on the Ni foam; the Ni-P@NiCo LDH was then directly used for a pseudocapacitive electrode. Owing to the splendid synergistic effect between Ni-P and NiCo LDH nanosheets as well as the hierarchical structure of 1D nanorods, 2D nanosheets, and 3D Ni foam, the hybrid electrode exhibited significantly enhanced electrochemical performances. The Ni-P@NiCo LDH electrode showed a high specific capacitance of 12.9 F cm -2 at 5 mA cm -2 (3470.5 F g -1 at a current density of 1.3 A g -1 ) that remained as high as 6.4 F cm -2 at a high current density of 100 mA cm -2 (1700 F g -1 at 27 A g -1 ) and excellent cycling stability (96% capacity retention after 10 000 cycles at 40 mA cm -2 ). Furthermore, the asymmetric supercapacitors (ASCs) were assembled using Ni-P@NiCo LDH as a positive electrode and activated carbon (AC) as a negative electrode. The obtained ASCs delivered remarkable energy density and power density as well as good cycling performance. The enhanced electrochemical activities open a new avenue for the development of supercapacitors.

An evaluation of two types of nickel-titanium wires in terms of micromorphology and nickel ions' release following oral environment exposure.

Science.gov (United States)

Ghazal, Abdul Razzak A; Hajeer, Mohammad Y; Al-Sabbagh, Rabab; Alghoraibi, Ibrahim; Aldiry, Ahmad

2015-01-01

This study aimed to compare superelastic and heat-activated nickel-titanium orthodontic wires' surface morphology and potential release of nickel ions following exposure to oral environment conditions. Twenty-four 20-mm-length distal cuts of superelastic (NiTi Force I®) and 24 20-mm-length distal cuts of heat-activated (Therma-Ti Lite®) nickel-titanium wires (American Orthodontics, Sheboygan, WI, USA) were divided into two equal groups: 12 wire segments left unused and 12 segments passively exposed to oral environment for 1 month. Scanning electron microscopy and atomic force microscopy were used to analyze surface morphology of the wires which were then immersed in artificial saliva for 1 month to determine potential nickel ions' release by means of atomic absorption spectrophotometer. Heat-activated nickel-titanium (NiTi) wires were rougher than superelastic wires, and both types of wires released almost the same amount of Ni ions. After clinical exposure, more surface roughness was recorded for superelastic NiTi wires and heat-activated NiTi wires. However, retrieved superelastic NiTi wires released less Ni ions in artificial saliva after clinical exposure, and the same result was recorded regarding heat-activated wires. Both types of NiTi wires were obviously affected by oral environment conditions; their surface roughness significantly increased while the amount of the released Ni ions significantly declined.

Oxidation mechanism and passive behaviour of nickel in molten carbonate

Energy Technology Data Exchange (ETDEWEB)

Vossen, J.P.T. (ECN Fossil Fuels, Petten (Netherlands)); Ament, P.C.H.; De Wit, J.H.W. (Div. of Corrosion, Lab. for Maaterials Sceince, Delft Univ. of Technology, Delft (Netherlands))

1994-07-01

The oxidation and passivation mechanism and the passive behaviour of nickel in molten carbonate have been investigated with impedance measurements. The oxidation of nickel proceeds according to a dissolution and reprecipitation process. The slowest steps in the reaction sequence are the dissociation reaction of the carbonate and the diffusion of the formed NiO to the metal surface. In the passive range, dissolution of Ni[sup 2+] proceeds after diffusion of Ni[sup 2+] through the oxide layer. The Ni[sup 2+] is formed at the metal/oxide interface. The slowest process is the diffusion of bivalent nickel ions through the passive scale. The formation of trivalent nickel ions probably takes place at the oxide/melt interface. This reaction is accompanied by the incorporation of an oxygen ion and a nickel vacancy in the NiO lattice. The trivalent nickel ions and the nickel vacancy diffuse to the bulk of the oxide scale. The slowest step in this sequence is the dissociation of the carbonate ions and the incorporation of the oxygen ion in the NiO lattice. 9 figs., 2 tabs., 11 refs.

Standard molar enthalpies of formation of nickel(II) {beta}-diketonates and monothio-{beta}-diketonates

Energy Technology Data Exchange (ETDEWEB)

Ribeiro da Silva, Manuel A.V. [Centro de Investigacao em Quimica, Departamento de Quimica, Faculdade de Ciencias, Universidade do Porto, Rua do Campo Alegre, 687, P-4169-007 Porto (Portugal)]. E-mail: risilva@fc.up.pt; Santos, Luis M.N.B.F. [Centro de Investigacao em Quimica, Departamento de Quimica, Faculdade de Ciencias, Universidade do Porto, Rua do Campo Alegre, 687, P-4169-007 Porto (Portugal); Giera, Edward [Faculty of Chemistry, Wroclaw University, ul. F. Joliot-Curie 14, 50-383 Wroclaw (Poland)

2007-03-15

The standard (p{sup o}=0.1MPa) molar enthalpies of formation of the crystalline diaquobis(dibenzoylmethanate)nickel(II), Ni(dbm){sub 2}(H{sub 2}O){sub 2}, diaquobis(thenoyltrifluoroacetonate)nickel(II), Ni(ttfa){sub 2}(H{sub 2}O){sub 2} bis(monothiodibenzoylmethanate)nickel(II), Ni(dbmS){sub 2} and bis(monothiothenoyltrifluoroacetonate)nickel(II), Ni(HttfaS){sub 2} were determined, at T=298.15K, by high precision solution-reaction calorimetry. The standard molar enthalpy of sublimation of the monothiothenoyltrifluoroacetone (HttfaS) complex was measured by high-temperature Calvet microcalorimetry. From the standard molar enthalpies of formation of the complexes in the gaseous state, the mean nickel(II)-ligand molar dissociation enthalpies, (Ni-L), were derived. {delta}{sub f}H{sub m}{sup o}(cr)/(kJ.mol{sup -1})Diaquobis(dibenzoylmethanate)nickel(II), Ni(dbm){sub 2}(H{sub 2}O){sub 2}-993.3+/-3.8Diaquobis(thenoyltrifluoroacetonate)nickel(II), Ni(ttfa){sub 2}(H{sub 2}O){sub 2}-2452.0+/-8.3Bis(monothiodibenzoylmethanate)nickel(II), Ni(dbmS){sub 2}-42.1+/-5.9Bis(monothiothenoyltrifluoroacetonate)nickel(II), Ni(ttfaS){sub 2}-1473.5+/-8.1.

A comparative study of humidity sensing and photocatalytic applications of pure and nickel (Ni)-doped WO{sub 3} thin films

Energy Technology Data Exchange (ETDEWEB)

Ramkumar, S. [Bannari Amman Institute of Technology, Department of Physics, Erode, Tamilnadu (India); Rajarajan, G. [Vidhya Mandhir Institute of Technology, Department of Physics, Erode, Tamilnadu (India)

2017-06-15

Nanocrystalline of pristine and nickel (Ni)-doped tungsten trioxide (WO{sub 3}) thin films was deposited by chemical bath deposition method. The concentrations of Ni ions were varied from 0 to 10 wt%. In order to improve the crystallinity of the films were annealed at 600 C for 2 h in the ambient atmosphere. X-ray diffraction results reveal that the WO{sub 3} doped with nickel crystallizes in monoclinic structure and the results are in good agreement with the standard JCPDS data (card no: 83-0951). AFM micrographs reveal that average grain size of about 27-39 nm for pure and Ni-doped WO{sub 3} thin films. In addition, the band gap of the Ni-doped WO{sub 3} nanostructures is facilely tunable by controlling the Ni contents. The humidity sensor setup was fabricated and measured for pure and Ni-doped WO{sub 3} thin film sensor with various level of RH (10-90%). The Ni-doped WO{sub 3} sensor showed fast response and high sensitivity than pure WO{sub 3}. The photocatalytic activities of the films were evaluated by degradation of methyl orange, methylene blue and phenol in an aqueous solution under visible light irradiation. The photocatalytic activity of WO{sub 3} nanostructures could be remarkably enhanced by doping the Ni impurity. (orig.)

Electroless Ni-P/Ni-B duplex coatings: preparation and evaluation of microhardness, wear and corrosion resistance

International Nuclear Information System (INIS)

Narayanan, T.S.N. Sankara; Krishnaveni, K.; Seshadri, S.K.

2003-01-01

The present work deals with the formation of Ni-P/Ni-B duplex coatings by electroless plating process and evaluation of their hardness, wear resistance and corrosion resistance. The Ni-P/Ni-B duplex coatings were prepared using dual baths (acidic hypophosphite- and alkaline borohydride-reduced electroless nickel baths) with both Ni-P and Ni-B as inner layers and with varying single layer thickness. Scanning electron microscopy (SEM) was used to assess the duplex interface. The microhardness, wear resistance and corrosion resistance of electroless nickel duplex coatings were compared with electroless Ni-P and Ni-B coatings of similar thickness. The study reveals that the Ni-P and Ni-B coatings are amorphous in their as-plated condition and upon heat-treatment at 450 deg. C for 1 h, both Ni-P and Ni-B coatings crystallize and produce nickel, nickel phosphide and nickel borides in the respective coatings. All the three phases are formed when Ni-P/Ni-B and Ni-B/Ni-P duplex coatings are heat-treated at 450 deg. C for 1 h. The duplex coatings are uniform and the compatibility between the layers is good. The microhardness, wear resistance and corrosion resistance of the duplex coating is higher than Ni-P and Ni-B coatings of similar thickness. Among the two types of duplex coatings studied, hardness and wear resistance is higher for coatings having Ni-B coating as the outer layer whereas better corrosion resistance is offered by coatings having Ni-P coating as the outer layer

Freeze-substitution methods for Ni localization and quantitative analysis in Berkheya coddii leaves by means of PIXE

International Nuclear Information System (INIS)

Budka, D.; Mesjasz-PrzybyIowicz, J.; Tylko, G.; PrzybyIowicz, W.J.

2005-01-01

Leaves of Ni hyperaccumulator Berkheya coddii were chosen as a model to investigate the influence of eight freeze-substitution protocols on the Ni content and distribution. Freeze-substitution of leaf samples cryofixed by high-pressure freezing was carried out in dry acetone, methanol, diethyl ether and tetrahydrofuran. The same substitution media were also used with dimethylglyoxime added as a precipitation reagent. The samples were infiltrated and embedded in Spurr's resin. Micro-PIXE analysis of Ni concentration and localization, complemented by proton backscattering for matrix assessment, was performed using the nuclear microprobe at Materials Research Group, iThemba LABS, South Africa. True elemental maps and concentrations were obtained using GeoPIXE-II software. The results were compared with the control results obtained for the parallel air-dried samples, corrected for the water content. The highest Ni content was found in the leaf samples substituted in diethyl ether. This concentration was statistically different from the results obtained for other media. In case of diethyl ether medium Ni was mainly localized in the mesophyll tissue, and the distribution map of this element was in accordance with previous results obtained for freeze-dried and frozen-hydrated leaves of this species. The same distribution pattern was observed for specimens embedded in dry acetone, but Ni concentration was significantly lower. Tetrahydrofuran medium preserved Ni preferentially in the epidermis and vascular tissue, and the elemental map for samples embedded in this medium was distorted. Ni was almost completely washed out from samples substituted in methanol and it was thus impossible to obtain a picture of its distribution. Dimethylglyoxime did not improve the preservation of this element. These results show that diethyl ether is a suitable substitution medium for assessment of Ni concentration and distribution in leaves of B. coddii

Electronic structure of Ni-- and Ni2--ethylene cluster complexes

International Nuclear Information System (INIS)

Basch, H.; Newton, M.D.; Moskowitz, J.W.

1978-01-01

The electronic structure of metal cluster--ethylene complexes has been investigated by carrying out ab initio bonding pair-correlated, self-consistent field, and configuration interaction (CI) calculations on the NiC 2 H 4 and Ni 2 C 2 H 4 species. The π-NiC 2 H 4 and π-Ni 2 C 2 H 4 cluster complexes are found to be bound, the former only with CI, while disigma-Ni 2 C 2 H 4 has only a repulsive Ni 2 --C 2 H 4 ground state potential curve. The bonding in the π-type cluster complexes can be described as follows: The metal atom configuration is 3d 9 4s 1 with the 4s hybridized (by the metal 4p) away from the ethylene molecule, thereby allowing the π orbital to form a dative sigma bond with the metal atom. The bonding interaction is promoted by the presence of a second nickel atom behind the first one, leading to a 4s orbital electron deficiency of the bonded nickel atom and thus making this nickel atom a better electron acceptor. Back donation from the occupied metal 3d into the ethylene π* molecular orbital also takes place to some extent, and thus both features of the classical Dewar--Chatt--Duncanson model are observed. The π-Ni 2 C 2 H 4 species is analyzed in terms of the addition of a bare nickel atom to a π-NiC 2 H 4 cluster complex, with concomitant stabilization of the orbitals of the bonded nickel atom. A study of the excited electronic states of π-NiC 2 H 4 shows that low-lying 4s→π* and 3d→π* (M→L) charge transfer transitions are predicted. The former is not observed experimentally, probably due to the diffuse nature of the 4s orbital. The relationship between small cluster--ethylene complex systems and ethylene chemisorption on a nickel metal surface is discussed

Discharge Characteristics of the Nickel Hydroxide Electrode in 30% KOH

International Nuclear Information System (INIS)

Kim, Young Jin

1989-01-01

The discharge behavior of the nickel hydroxide electrode has been investigated in 30% KOH at 25 .deg. C. Two voltage plateaus are displayed on the discharge curve of C/20. It is shown that the impedance of the nickel hydroxide electrode increases with decrease of the discharge potential. The discharge behavior of the nickel hydroxide electrode has been investigated in 30% KOH indicating the reduction of the β-NiOOH to the β-Ni(OH) 2 by proton diffusion process and hence the electronic conductivity change of the nickel hydroxide electrode. Furthermore, the γ-NiOOH, produced by prolonged oxidation of the β-NiOOH in 30% KOH, discharges at a slightly lower potential than the β-Ni(OH) 2 that could result in the life-limiting factor of several alkaline electrolyte storage batteries using the nickel hydroxide electrode as the positive plate

Tuning crystal phase of NiS{sub x} through electro-oxidized nickel foam: A novel route for preparing efficient electrocatalysts for oxygen evolution reaction

Energy Technology Data Exchange (ETDEWEB)

Li, Xiao; Shang, Xiao [State Key Laboratory of Heavy Oil Processing, China University of Petroleum (East China), Qingdao 266580 (China); Rao, Yi [State Key Laboratory of Heavy Oil Processing, China University of Petroleum (East China), Qingdao 266580 (China); College of Science, China University of Petroleum (East China), Qingdao 266580, PR China (China); Dong, Bin, E-mail: dongbin@upc.edu.cn [State Key Laboratory of Heavy Oil Processing, China University of Petroleum (East China), Qingdao 266580 (China); College of Science, China University of Petroleum (East China), Qingdao 266580, PR China (China); Han, Guan-Qun [State Key Laboratory of Heavy Oil Processing, China University of Petroleum (East China), Qingdao 266580 (China); College of Science, China University of Petroleum (East China), Qingdao 266580, PR China (China); Hu, Wen-Hui; Liu, Yan-Ru; Yan, Kai-Li; Chi, Jing-Qi; Chai, Yong-Ming [State Key Laboratory of Heavy Oil Processing, China University of Petroleum (East China), Qingdao 266580 (China); Liu, Chen-Guang, E-mail: cgliu@upc.edu.cn [State Key Laboratory of Heavy Oil Processing, China University of Petroleum (East China), Qingdao 266580 (China)

2017-02-28

Highlights: • Electro-oxidized nickel foam as a support has been used to prepare NiS{sub x} phases. • Ni(OH){sub 2} layer on electro-oxidized NF is responsible for the growth of β-NiS. • NiS{sub x}/NF(Ox) composed of β-NiS and Ni{sub 3}S{sub 2} has enhanced electrocatalytic activity. • The growth mechanisms of mixed NiS{sub x} phases of NiS{sub x}/NF(Ox) have been discussed. - Abstract: A facile solvothermal sulfurization using electro-oxidized nickel foam (NF(Ox)) as support has been applied to prepare NiS{sub x}/NF(Ox) electrocatalyst with highly efficient activity for oxygen evolution reaction (OER). XRD patterns confirm the composition of NiS{sub x}/NF(Ox): two kinds of crystal phase including β-NiS and Ni{sub 3}S{sub 2}. While using bare NF as support under identical conditions, only Ni{sub 3}S{sub 2} phase can be detected. SEM images reveal two kinds of morphologies of NiS{sub x}/NF(Ox) including pyramids structure of β-NiS and nanorod-like structure of Ni{sub 3}S{sub 2}, which implies the tuning effect of electro-pretreatment of NF on the selective preparation of NiS{sub x} crystal phase. It can be speculated that Ni(OH){sub 2} layer derived from electro-oxidized NF is responsible for the growth of β-NiS while metallic Ni is transformed into Ni{sub 2}S{sub 3} during sulfurization. Electrochemical measurements for OER indicate the enhanced electrocatalytic activity of NiS{sub x}/NF(Ox) with a small overpotential of 72 mV to reach 10 mA cm{sup −2} compared with Ni{sub 3}S{sub 2}/NF, which may be ascribed to the improved electron-transfer kinetics relating to the unique atomic configurations and crystalline structures of β-NiS. The electro-oxidation pretreatment of nickel foam provides a simple and convenient method by tuning different NiS{sub x} crystal phases for preparing excellent OER eletrocatalysts.

Electrodeposition behavior of nickel and nickel-zinc alloys from the zinc chloride-1-ethyl-3-methylimidazolium chloride low temperature molten salt

International Nuclear Information System (INIS)

Gou Shiping; Sun, I.-W.

2008-01-01

The electrodeposition of nickel and nickel-zinc alloys was investigated at polycrystalline tungsten electrode in the zinc chloride-1-ethyl-3-methylimidazolium chloride molten salt. Although nickel(II) chloride dissolved easily into the pure chloride-rich 1-ethyl-3-methylimidazolium chloride ionic melt, metallic nickel could not be obtained by electrochemical reduction of this solution. The addition of zinc chloride to this solution shifted the reduction of nickel(II) to more positive potential making the electrodeposition of nickel possible. The electrodeposition of nickel, however, requires an overpotential driven nucleation process. Dense and compact nickel deposits with good adherence could be prepared by controlling the deposition potential. X-ray powder diffraction measurements indicated the presence of crystalline nickel deposits. Non-anomalous electrodeposition of nickel-zinc alloys was achieved through the underpotential deposition of zinc on the deposited nickel at a potential more negative than that of the deposition of nickel. X-ray powder diffraction and energy-dispersive spectrometry measurements of the electrodeposits indicated that the composition and the phase types of the nickel-zinc alloys are dependent on the deposition potential. For the Ni-Zn alloy deposits prepared by underpotential deposition of Zn on Ni, the Zn content in the Ni-Zn was always less than 50 atom%

Sintering of nickel catalysts. Effects of time, atmosphere, temperature, nickel-carrier interactions, and dopants

Energy Technology Data Exchange (ETDEWEB)

Sehested, Jens; Gelten, Johannes A.P.; Helveg, Stig [Haldor Topsoee A/S, Nymoellevej 55, DK-2800 Kgs. Lyngby (Denmark)

2006-08-01

Supported nickel catalysts are widely used in the steam-reforming process for industrial scale production of hydrogen and synthesis gas. This paper provides a study of sintering in nickel-based catalysts (Ni/Al{sub 2}O{sub 3} and Ni/MgAl{sub 2}O{sub 4}). Specifically the influence of time, temperature, atmosphere, nickel-carrier interactions and dopants on the rate of sintering is considered. To probe the sintering kinetics, all catalysts were analyzed by sulfur chemisorption to determine the Ni surface area. Furthermore selected samples were further analyzed using X-ray diffraction (XRD), mercury porosimetry, BET area measurements, and electron microscopy (EM). The observed sintering rates as a function of time, temperature, and P{sub H{sub 2}O}/P{sub H{sub 2}} ratio were consistent with recent model predictions [J. Sehested, J.A.P. Gelten, I.N. Remediakis, H. Bengaard, J.K. Norskov, J. Catal. 223 (2004) 432] over a broad range of environmental conditions. However, exposing the catalysts to severe sintering conditions the loss of nickel surface area is faster than model predictions and the deviation is attributed to a change in the sintering mechanism and nickel removal by nickel-carrier interactions. Surprisingly, alumina-supported Ni particles grow to sizes larger than the particle size of the carrier indicating that the pore diameter does not represent an upper limit for Ni particle growth. The effects of potassium promotion and sulfur poisoning on the rates of sintering were also investigated. No significant effects of the dopants were observed after ageing at ambient pressure. However, at high pressures of steam and hydrogen (31bar and H{sub 2}O:H{sub 2}=10:1) potassium promotion increased the sintering rate relative to that of the unpromoted catalyst. Sulfur also enhances the rate of sintering at high pressures, but the effect of sulfur is less than for potassium. (author)

Solvothermal synthesis of NiAl double hydroxide microspheres on a nickel foam-graphene as an electrode material for pseudo-capacitors

International Nuclear Information System (INIS)

Momodu, Damilola; Bello, Abdulhakeem; Dangbegnon, Julien; Barzeger, Farshad; Taghizadeh, Fatimeh; Fabiane, Mopeli; Manyala, Ncholu; Johnson, A. T. Charlie

2014-01-01

In this paper, we demonstrate excellent pseudo-capacitance behavior of nickel-aluminum double hydroxide microspheres (NiAl DHM) synthesized by a facile solvothermal technique using tertbutanol as a structure-directing agent on nickel foam-graphene (NF-G) current collector as compared to use of nickel foam current collector alone. The structure and surface morphology were studied by X-ray diffraction analysis, Raman spectroscopy and scanning and transmission electron microscopies respectively. NF-G current collector was fabricated by chemical vapor deposition followed by an ex situ coating method of NiAl DHM active material which forms a composite electrode. The pseudocapacitive performance of the composite electrode was investigated by cyclic voltammetry, constant charge–discharge and electrochemical impedance spectroscopy measurements. The composite electrode with the NF-G current collector exhibits an enhanced electrochemical performance due to the presence of the conductive graphene layer on the nickel foam and gives a specific capacitance of 1252 F g −1 at a current density of 1 A g −1 and a capacitive retention of about 97% after 1000 charge–discharge cycles. This shows that these composites are promising electrode materials for energy storage devices

Effect on growth and nickel content of cabbage plants watered with nickel solutions

Energy Technology Data Exchange (ETDEWEB)

Christensen, O B

1979-01-01

Chinese cabbage plants were watered with different concentrations of NiCl/sub 2/ solutions and the effect on growth and uptake of nickel in the plants were studied. No toxic effect on plant growth was observed. A higher content of nickel was found in the plants exposed to more concentrated nickel solutions. Nickel contamination and its clinical consequences are discussed. 29 references, 1 figure, 1 table.

Fe, Cr, Ni, Cu, Mg, Al, Ti, and S contents in plants and soil of heaps of nickel smelting works

Energy Technology Data Exchange (ETDEWEB)

Banasova, V; Hajduk, J

1977-01-01

The writers established the Fe, Ce, Cr, Ni, Ca, Mg, Al, Ti and S contents in the neopedon of heaps piling up from processing of nickel ore as well as in the plants: Cardaria draba, Salsola cali, Agropyrum repens, Bromus erectus, Calamagrostis epigeios, Cynodon dactylon and Matricaria inodora, growing on such heaps. Ca, Mg and S contents were found to be higher in dicotyledons and Fe, Al, Ti, Ni and Cr contents higher in monocotyledons. The analyzed dicotyledons appeared to be concentrators of Ca and S. Highest Fe, Al, Ti, Ni and Cr contents were found in individuals of the species Agropyrum repens. The neopedon as well as the plants had extraordinarily high Cr concentrations. The species Salsola cali has been found to possess an unusually higher affinity to the dump substrate after processing of nickel ore and to be a concentrator of Mg. 16 references, 1 table.

Drinking water pollution with nickel from water boilers; Nickel-Eintrag aus Wasserkochern ins Trinkwasser

Energy Technology Data Exchange (ETDEWEB)

Helmers, E. [Amt fuer Umweltschutz, Stuttgart (Germany). Chemisches Inst.

1998-07-01

The EU is planning to drop the threshold value for nickel in drinking water down to 20 {mu}g/l (present German threshold value: 50 {mu}g/l). Since ICP-MS-screenings of spot checks of water cookers were striking with respect to nickel, emissions of electrical water cookers have been investigated systematically within this study. As a result, water cookers with open heating coils are emitting relevant amounts of nickel into the water while it is brought to the boil. Investigation of eight preused water cookers with open heating coils revealed that the boiled water contained more than 50 {mu}g Ni/l in one case, more than 20 {mu}g Ni/l in two cases and, between 10 and 20 {mu}g Ni/l in two more cases, respectively. Removing of the lime by the aid of citric acid is increasing the nickel concentrations by a factor of up to 50 (max. 640 {mu}g/l). A new device was checked in a long-term test. During standard use with tapwater, Ni concentrations fall below the detection limit of 5 {mu}g Ni/l (120 cooking events). However, after removing of the lime, 5 times of cooking were necessary in order to diminish the Ni concentrations below the limit of 20 {mu}g/l. In the case of dionized water Ni concentrations below the limit of 20 {mu}g/l. In the case of deionized water Ni concentrations remained between 94 und 190 {mu}g/l. Health risk assessment: The intake of nickel with beverages made from hot water out of these cookers is in the range of 26 {mu}g/day. Considering an alltogether dietary nickel intake of 130-170 (900) {mu}g/day, this is not beyond the scope. However, according to the fact that nickel allergies (dermatitis) are very frequent (up to 13% of the population), this source should be limited or closed. (orig.) [Deutsch] Aus Anlass der geplanten Absenkung des Trinkwassergrenzwertes fuer Nickel auf 20 {mu}g/l sowie aufgrund von Auffaelligkeiten bei Stichprobenuntersuchungen wurde das Nickel-Emissionsverhalten von elektrischen Wassererhitzern betrachtet. Hierbei erwies sich

Investigation of hydrogen evolution activity for the nickel, nickel-molybdenum nickel-graphite composite and nickel-reduced graphene oxide composite coatings

International Nuclear Information System (INIS)

Jinlong, Lv; Tongxiang, Liang; Chen, Wang

2016-01-01

Graphical abstract: - Highlights: • Improved HER efficiency of Ni-Mo coatings was attributed to ‘cauliflower’ like microstructure. • RGO in nickel-RGO composite coating promoted refined grain and facilitated HER. • Synergistic effect between nickel and RGO facilitated HER due to large specific surface of RGO. - Abstract: The nickel, nickel-molybdenum alloy, nickel-graphite and nickel-reduced graphene oxide composite coatings were obtained by the electrodeposition technique from a nickel sulfate bath. Nanocrystalline molybdenum, graphite and reduced graphene oxide in nickel coatings promoted hydrogen evolution reaction in 0.5 M H_2SO_4 solution at room temperature. However, the nickel-reduced graphene oxide composite coating exhibited the highest electrocatalytic activity for the hydrogen evolution reaction in 0.5 M H_2SO_4 solution at room temperature. A large number of gaps between ‘cauliflower’ like grains could decrease effective area for hydrogen evolution reaction in slight amorphous nickel-molybdenum alloy. The synergistic effect between nickel and reduced graphene oxide promoted hydrogen evolution, moreover, refined grain in nickel-reduced graphene oxide composite coating and large specific surface of reduced graphene oxide also facilitated hydrogen evolution reaction.

Investigation of hydrogen evolution activity for the nickel, nickel-molybdenum nickel-graphite composite and nickel-reduced graphene oxide composite coatings

Energy Technology Data Exchange (ETDEWEB)

Jinlong, Lv, E-mail: ljlbuaa@126.com [Beijing Key Laboratory of Fine Ceramics, Institute of Nuclear and New Energy Technology, Tsinghua University, Zhongguancun Street, Haidian District, Beijing 100084 (China); State Key Lab of New Ceramic and Fine Processing, Tsinghua University, Beijing 100084 (China); Tongxiang, Liang; Chen, Wang [Beijing Key Laboratory of Fine Ceramics, Institute of Nuclear and New Energy Technology, Tsinghua University, Zhongguancun Street, Haidian District, Beijing 100084 (China); State Key Lab of New Ceramic and Fine Processing, Tsinghua University, Beijing 100084 (China)

2016-03-15

Graphical abstract: - Highlights: • Improved HER efficiency of Ni-Mo coatings was attributed to ‘cauliflower’ like microstructure. • RGO in nickel-RGO composite coating promoted refined grain and facilitated HER. • Synergistic effect between nickel and RGO facilitated HER due to large specific surface of RGO. - Abstract: The nickel, nickel-molybdenum alloy, nickel-graphite and nickel-reduced graphene oxide composite coatings were obtained by the electrodeposition technique from a nickel sulfate bath. Nanocrystalline molybdenum, graphite and reduced graphene oxide in nickel coatings promoted hydrogen evolution reaction in 0.5 M H{sub 2}SO{sub 4} solution at room temperature. However, the nickel-reduced graphene oxide composite coating exhibited the highest electrocatalytic activity for the hydrogen evolution reaction in 0.5 M H{sub 2}SO{sub 4} solution at room temperature. A large number of gaps between ‘cauliflower’ like grains could decrease effective area for hydrogen evolution reaction in slight amorphous nickel-molybdenum alloy. The synergistic effect between nickel and reduced graphene oxide promoted hydrogen evolution, moreover, refined grain in nickel-reduced graphene oxide composite coating and large specific surface of reduced graphene oxide also facilitated hydrogen evolution reaction.

In situ coating nickel organic complexes on free-standing nickel wire films for volumetric-energy-dense supercapacitors.

Science.gov (United States)

Hong, Min; Xu, Shusheng; Yao, Lu; Zhou, Chao; Hu, Nantao; Yang, Zhi; Hu, Jing; Zhang, Liying; Zhou, Zhihua; Wei, Hao; Zhang, Yafei

2018-07-06

A self-free-standing core-sheath structured hybrid membrane electrodes based on nickel and nickel based metal-organic complexes (Ni@Ni-OC) was designed and constructed for high volumetric supercapacitors. The self-standing Ni@Ni-OC film electrode had a high volumetric specific capacity of 1225.5 C cm -3 at 0.3 A cm -3 and an excellent rate capability. Moreover, when countered with graphene-carbon nanotube (G-CNT) film electrode, the as-assembled Ni@Ni-OC//G-CNT hybrid supercapacitor device delivered an extraordinary volumetric capacitance of 85 F cm -3 at 0.5 A cm -3 and an outstanding energy density of 33.8 at 483 mW cm -3 . Furthermore, the hybrid supercapacitor showed no capacitance loss after 10 000 cycles at 2 A cm -3 , indicating its excellent cycle stability. These fascinating performances can be ascribed to its unique core-sheath structure that high capacity nano-porous nickel based metal-organic complexes (Ni-OC) in situ coated on highly conductive Ni wires. The impressive results presented here may pave the way to construct s self-standing membrane electrode for applications in high volumetric-performance energy storage.

Environmental and human toxicology of nickel - a review; Umwelt- und Humantoxikologie von Nickel - eine aktuelle Uebersicht

Energy Technology Data Exchange (ETDEWEB)

Beyersmann, D. [Fachbereich Biologie und Chemie, Univ. Bremen (Germany)

2006-07-01

Nickel is a relatively rare element, and its concentrations in ambient air, soils and waters are very low. Higher burdens of nickel are found in nickel industries and their proximity. The human uptake of nickel from the ambient air is neglectably low, except in industrial exposures. The main fraction of human nickel uptake is from food, nearly 50% stems from vegetables. Only about 2% of the oral uptake of nickel are resorbed and distributed over all organs investigated. The uptake of nickel compounds through the skin generally is very low. However, chronic skin contact with nickel and nickel compounds causes a specific contact allergy. This disease was observed after occupational exposure but also frequently in the general population. The number of new cases has dropped considerably due to reinforced prevention. Epidemiological studies with workers of nickel smelting and refining plants have demonstrated increased risks of nose and lung cancer. Human data are supported by results from animal experiments which have shown that inhalation of various nickel compounds caused lung cancer. Furthermore, animal experiments have yielded evidence that oral and inhalative exposure to nickel compounds impair reproduction. National and international agencies have classified various nickel compounds as carcinogenic to humans. The unit cancer risk attributed to life-long inhalation of 1 {mu}g Ni/m{sup 3} air is estimated to be between 2 x 10{sup -4} and 7 x 10{sup -4}. Occupational exposure limits in Germany have been the Technical Guidance Values of 0.5 mg/m{sup 3} for nickel and weakly soluble nickel compounds and of 0.05 mg/m{sup 3} for inhalable droplets of soluble nickel salts. The German limit value for ambient immission is 0.015 mg Ni/m{sup 2}. d, and for emission 0,5 mg Ni/m{sup 3}. Limit values for nickel in air are to be taken not as safe thresholds but as guidance values for the delimitation of the cancer risk. (orig.)

Comparative in vitro biocompatibility of nickel-titanium, pure nickel, pure titanium, and stainless steel: genotoxicity and atomic absorption evaluation.

Science.gov (United States)

Assad, M; Lemieux, N; Rivard, C H; Yahia, L H

1999-01-01

The genotoxicity level of nickel-titanium (NiTi) was compared to that of its pure constituents, pure nickel (Ni) and pure titanium (Ti) powders, and also to 316L stainless steel (316L SS) as clinical reference material. In order to do so, a dynamic in vitro semiphysiological extraction was performed with all metals using agitation and ISO requirements. Peripheral blood lymphocytes were then cultured in the presence of all material extracts, and their comparative genotoxicity levels were assessed using electron microscopy-in situ end-labeling (EM-ISEL) coupled to immunogold staining. Cellular chromatin exposition to pure Ni and 316L SS demonstrated a significantly stronger gold binding than exposition to NiTi, pure Ti, or the untreated control. In parallel, graphite furnace atomic absorption spectrophotometry (AAS) was also performed on all extraction media. The release of Ni atoms took the following decreasing distribution for the different resulting semiphysiological solutions: pure Ni, 316L SS, NiTi, Ti, and controls. Ti elements were detected after elution of pure titanium only. Both pure titanium and nickel-titanium specimens obtained a relative in vitro biocompatibility. Therefore, this quantitative in vitro study provides optimistic results for the eventual use of nickel-titanium alloys as surgical implant materials.

Ultrasonic preparation of nano-nickel/activated carbon composite using spent electroless nickel plating bath and application in degradation of 2,6-dichlorophenol.

Science.gov (United States)

Su, Jingyu; Jin, Guanping; Li, Changyong; Zhu, Xiaohui; Dou, Yan; Li, Yong; Wang, Xin; Wang, Kunwei; Gu, Qianqian

2014-11-01

Ni was effectively recovered from spent electroless nickel (EN) plating baths by forming a nano-nickel coated activated carbon composite. With the aid of ultrasonication, melamine-formaldehyde-tetraoxalyl-ethylenediamine chelating resins were grafted on activated carbon (MFT/AC). PdCl2 sol was adsorbed on MFT/AC, which was then immersed in spent electroless nickel plating bath; then nano-nickel could be reduced by ascorbic acid to form a nano-nickel coating on the activated carbon composite (Ni/AC) in situ. The materials present were carefully examined by Fourier transform infrared spectroscopy, X-ray diffraction, field emission scanning electron microscopy, X-ray photoelectron spectroscopy and electrochemistry techniques. The resins were well distributed on the inside and outside surfaces of activated carbon with a size of 120 ± 30 nm in MFT/AC, and a great deal of nano-nickel particles were evenly deposited with a size of 3.8 ± 1.1 nm in Ni/MFT. Moreover, Ni/AC was successfully used as a catalyst for ultrasonic degradation of 2,6-dichlorophenol. Copyright © 2014. Published by Elsevier B.V.

Effect of chelating agents and metal ions on nickel bioavailability and chlorophyll fluorescence response in wheat- An approach for attenuation of Ni stress

Directory of Open Access Journals (Sweden)

Nilima Patnaik

2012-08-01

Full Text Available The objectives of the study are to analyze the physiological changes, biochemical alterations and attenuation of nickel toxicity effects in wheat seedlings under combined applications of Ni ions, metal chelators (EDTA/Citric Acid and metal ions (Zn2+ /Mg2+. Wheat (Triticum aestivum L cv UP262 seedlings were grown hydroponically using different concentrations of Ni up to 7 days along with chelators and metal ions for study. The seedling growth was maximum with NiCl2–Zn2+ (100μM and minimum with NiCl2–EDTA (100μM treatments. Total chlorophyll content was maximum in the seedlings treated with NiCl2-Zn2+ (100μM and minimum in NiCl2-EDTA (100μM treatments. NiCl2–EDTA (100μM showed less Fo and Fm values and therefore, a trend in the decrease in OJIP transient indicates the maximum alteration of photochemical activity of PS-II in presence of NiCl2–EDTA (100μM treatment. Similar observation was found by NiCl2 –EDTA (200μM treatment where Fo and Fm values were noted to decline. High nickel content in roots of the seedlings was noted as compared to shoots.

Texture Formation of Electroplated Nickel and Nickel Alloy on Cu Substrate

International Nuclear Information System (INIS)

Lee, Hee Gyoun; Hong, Gye Won; Kim, Jae Geun; Lee, Sun Wang; Kim, Ho Jin

2006-01-01

Nickel and nickel-tungsten alloy were electroplated on a cold rolled and heat treated copper(Cu) substrate. 4 mm-thick high purity commercial grade Cu was rolled to various thicknesses of 50, 70, 100 and 150 micron. High reduction ratio of 30% was applied down to 150 micron. Rolled texture was converted into cube texture via high temperature heat treatment at 400-800 degrees C. Grain size of Cu was about 50 micron which is much smaller compared to >300 micron for the Cu prepared using smaller reduction pass of 5%. 1.5 km-long 150 micron Cu was fabricated with a rolling speed of 33 m/min and texture of Cu was uniform along length. Abnormal grain growth and non-cube texture appeared for the specimen anneal above 900 degrees C. 1-10 micron thick Ni and Ni-W film was electroplated onto an annealed cube-textured Cu or directly on a cold rolled Cu. Both specimens were annealed and the degree of texture was measured. For electroplating of Ni on annealed Cu, Ni layer duplicated the cube-texture of Cu substrate and the FWHM of in plane XRD measurement for annealed Cu layer and electroplated layer was 9.9 degree and 13.4 degree, respectively. But the FWHM of in plane XRD measurement of the specimen which electroplated Ni directly on cold rolled Cu was 8.6 degree, which is better texture than that of nickel electroplated on annealed Cu and it might be caused by the suppression of secondary recrystallization and abnormal grain growth of Cu at high temperature above 900 degrees C by electroplated nickel.

Nickel Oxide and Nickel Co-doped Graphitic Carbon Nitride Nanocomposites and its Octylphenol Sensing Application

KAUST Repository

Gong, Wanyun; Zou, Jing; Zhang, Sheng; Zhou, Xin; Jiang, Jizhou

2015-01-01

Nickel oxide and nickel co-doped graphitic carbon nitride (NiO-Ni-GCN) nanocomposites were successfully prepared by thermal treatment of melamine and NiCl2 6H2O. NiO-Ni-GCN nanocomposites showed superior electrochemical catalytic activity for the oxidation of octylphenol to pure GCN. A detection method of octylphenol in environmental water samples was developed based at NiO-Ni-GCN nanocomposites modified electrode under infrared light irradiation. Differential pulse voltammetry was used as the analytic technique of octylphenol, exhibiting stable and specific concentration-dependent oxidation signal in the presence of octylphenol in the range of 10nM to 1μM and 1μM to 50μM, with a detection limit of 3.3nM (3S/N). © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Nickel Oxide and Nickel Co-doped Graphitic Carbon Nitride Nanocomposites and its Octylphenol Sensing Application

KAUST Repository

Gong, Wanyun

2015-11-16

Nickel oxide and nickel co-doped graphitic carbon nitride (NiO-Ni-GCN) nanocomposites were successfully prepared by thermal treatment of melamine and NiCl2 6H2O. NiO-Ni-GCN nanocomposites showed superior electrochemical catalytic activity for the oxidation of octylphenol to pure GCN. A detection method of octylphenol in environmental water samples was developed based at NiO-Ni-GCN nanocomposites modified electrode under infrared light irradiation. Differential pulse voltammetry was used as the analytic technique of octylphenol, exhibiting stable and specific concentration-dependent oxidation signal in the presence of octylphenol in the range of 10nM to 1μM and 1μM to 50μM, with a detection limit of 3.3nM (3S/N). © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Magnetoelectric Effect in Gallium Arsenide-Nickel-Tin-Nickel Multilayer Structures

Science.gov (United States)

Filippov, D. A.; Tikhonov, A. A.; Laletin, V. M.; Firsova, T. O.; Manicheva, I. N.

2018-02-01

Experimental data have been presented for the magnetoelectric effect in nickel-tin-nickel multilayer structures grown on a GaAs substrate by cathodic electrodeposition. The method of fabricating these structures has been described, and the frequency dependence of the effect has been demonstrated. It has been shown that tin used as an intermediate layer reduces mechanical stresses due to the phase mismatch at the Ni-GaAs interface and, thus, makes it possible to grow good structures with a 70-μm-thick Ni layer. The grown structures offer good adhesion between layers and a high Q factor.

Electrochemical Behaviour of Ni and Ni-PVC Electrodes for the Electroxidation of Ethanol

International Nuclear Information System (INIS)

Mohd Syafiq Hamdan; Norazzizi Nordin; Siti Fathrita Mohd Amir; Riyanto; Mohamed Rozali Othman

2011-01-01

In this study, two nickel based electrodes were prepared; nickel foil and nickel-polyvinylchloride (Ni-PVC), in order to study their electrochemical behavior using cyclic voltammetry, CV and chronocoulometry, CC. Ni electrode was prepared from Ni metal foil while Ni-PVC electrode was prepared by mixing a weighed portion of Ni powder and PVC in THF solvent, swirled until the suspension was homogeneous and drying the suspension in an oven at 50 degree Celsius for 3 h. The dry sample was then placed in a 1 cm diameter stainless steel mould and pressed at 10 ton/ cm 2 . From CV data, Ni-PVC electrode showed a better electrochemical behavior compared to Ni metal foil electrode. The use of Ni-PVC electrode at higher concentration of supporting electrolyte (1.0 M KOH) was better than at lower concentration of the same supporting electrolyte in electroxidation of ethanol. In addition to acetic acid, the oxidation of ethanol also produced ethyl acetate and acetaldehyde. (author)

Ni adsorption and Ni-Al LDH precipitation in a sandy aquifer: An experimental and mechanistic modeling study

NARCIS (Netherlands)

Regelink, I.C.; Temminghoff, E.J.M.

2011-01-01

Mining activities and industries have created nickel (Ni) contaminations in many parts of the world. The objective of this study is to increase our understanding of Ni adsorption and Nickel-Aluminium Layered Double Hydroxide (Ni-Al LDH) precipitation to reduce Ni mobility in a sandy soil aquifer. At

Effect of Nickel Equivalent on Austenite Transition Ratio in Ni-Mn-Cu Cast Iron

Directory of Open Access Journals (Sweden)

Janus A.

2013-06-01

Full Text Available Determined was quantitative effect of nickel equivalent value on austenite decomposition degree during cooling-down castings of Ni-Mn- Cu cast iron. Chemical composition of the alloy was 1.8 to 5.0 % C, 1.3 to 3.0 % Si, 3.1 to 7.7 % Ni, 0.4 to 6.3 % Mn, 0.1 to 4.9 % Cu, 0.14 to 0.16 % P and 0.03 to 0.04 % S. Analysed were castings with representative wall thickness 10, 15 and 20 mm. Scope of the examination comprised chemical analysis (including WDS, microscopic observations (optical and scanning microscopy, image analyser, as well as Brinell hardness and HV microhardness measurements of structural components.

In situ Ni-doping during cathodic electrodeposition of hematite for excellent photoelectrochemical performance of nanostructured nickel oxide-hematite p-n junction photoanode

Energy Technology Data Exchange (ETDEWEB)

Phuan, Yi Wen, E-mail: phuan.yi.wen@monash.edu [School of Engineering, Chemical Engineering Discipline, Monash University Malaysia, Jalan Lagoon Selatan, Bandar Sunway, Selangor DE 47500 (Malaysia); Ibrahim, Elyas, E-mail: meibr2@student.monash.edu [School of Engineering, Chemical Engineering Discipline, Monash University Malaysia, Jalan Lagoon Selatan, Bandar Sunway, Selangor DE 47500 (Malaysia); Chong, Meng Nan, E-mail: Chong.Meng.Nan@monash.edu [School of Engineering, Chemical Engineering Discipline, Monash University Malaysia, Jalan Lagoon Selatan, Bandar Sunway, Selangor DE 47500 (Malaysia); Sustainable Water Alliance, Advanced Engineering Platform, Monash University Malaysia, Jalan Lagoon Selatan, Bandar Sunway, Selangor DE 47500 (Malaysia); Zhu, Tao, E-mail: zhu.tao@monash.edu [School of Engineering, Chemical Engineering Discipline, Monash University Malaysia, Jalan Lagoon Selatan, Bandar Sunway, Selangor DE 47500 (Malaysia); Lee, Byeong-Kyu, E-mail: bklee@ulsan.ac.kr [Department of Civil and Environmental Engineering, University of Ulsan, Nam-gu, Daehakro 93, Ulsan 680-749 (Korea, Republic of); Ocon, Joey D., E-mail: jdocon@up.edu.ph [Laboratory of Electrochemical Engineering (LEE), Department of Chemical Engineering, University of the Philippines Diliman, Quezon City 1101 (Philippines); Chan, Eng Seng, E-mail: chan.eng.seng@monash.edu [School of Engineering, Chemical Engineering Discipline, Monash University Malaysia, Jalan Lagoon Selatan, Bandar Sunway, Selangor DE 47500 (Malaysia)

2017-01-15

Highlights: • NiO-hematite p-n junction photoanodes were fabricated via an in situ Ni-doping. • The fundamental mechanism of Ni{sup 2+} ions involved was elucidated. • The optimum Ni dopant was 25 M% for the highest photocurrent density. • It exhibited an excellent photoelectrochemical performance of 7-folds enhancement. - Abstract: Nanostructured nickel oxide-hematite (NiO/α-Fe{sub 2}O{sub 3}) p-n junction photoanodes synthesized from in situ doping of nickel (Ni) during cathodic electrodeposition of hematite were successfully demonstrated. A postulation model was proposed to explain the fundamental mechanism of Ni{sup 2+} ions involved, and the eventual formation of NiO on the subsurface region of hematite that enhanced the potential photoelectrochemical water oxidation process. Through this study, it was found that the measured photocurrent densities of the Ni-doped hematite photoanodes were highly dependent on the concentrations of Ni dopant used. The optimum Ni dopant at 25 M% demonstrated an excellent photoelectrochemical performance of 7-folds enhancement as compared to bare hematite photoanode. This was attributed to the increased electron donor density through the p-n junction and thus lowering the energetic barrier for water oxidation activity at the optimum Ni dopant concentration. Concurrently, the in situ Ni-doping of hematite has also lowered the photogenerated charge carrier transfer resistance as measured using the electrochemical impedance spectroscopy. It is expected that the fundamental understanding gained through this study is helpful for the rational design and construction of highly efficient photoanodes for application in photoelectrochemical process.

In situ Ni-doping during cathodic electrodeposition of hematite for excellent photoelectrochemical performance of nanostructured nickel oxide-hematite p-n junction photoanode

International Nuclear Information System (INIS)

Phuan, Yi Wen; Ibrahim, Elyas; Chong, Meng Nan; Zhu, Tao; Lee, Byeong-Kyu; Ocon, Joey D.; Chan, Eng Seng

2017-01-01

Highlights: • NiO-hematite p-n junction photoanodes were fabricated via an in situ Ni-doping. • The fundamental mechanism of Ni"2"+ ions involved was elucidated. • The optimum Ni dopant was 25 M% for the highest photocurrent density. • It exhibited an excellent photoelectrochemical performance of 7-folds enhancement. - Abstract: Nanostructured nickel oxide-hematite (NiO/α-Fe_2O_3) p-n junction photoanodes synthesized from in situ doping of nickel (Ni) during cathodic electrodeposition of hematite were successfully demonstrated. A postulation model was proposed to explain the fundamental mechanism of Ni"2"+ ions involved, and the eventual formation of NiO on the subsurface region of hematite that enhanced the potential photoelectrochemical water oxidation process. Through this study, it was found that the measured photocurrent densities of the Ni-doped hematite photoanodes were highly dependent on the concentrations of Ni dopant used. The optimum Ni dopant at 25 M% demonstrated an excellent photoelectrochemical performance of 7-folds enhancement as compared to bare hematite photoanode. This was attributed to the increased electron donor density through the p-n junction and thus lowering the energetic barrier for water oxidation activity at the optimum Ni dopant concentration. Concurrently, the in situ Ni-doping of hematite has also lowered the photogenerated charge carrier transfer resistance as measured using the electrochemical impedance spectroscopy. It is expected that the fundamental understanding gained through this study is helpful for the rational design and construction of highly efficient photoanodes for application in photoelectrochemical process.

Solidification phenomena in nickel base brazes containing boron and silicon

International Nuclear Information System (INIS)

Tung, S.K.; Lim, L.C.; Lai, M.O.

1996-01-01

Nickel base brazes containing boron and/or silicon as melting point depressants are used extensively in the repair and joining of aero-engine hot-section components. These melting point depressants form hard and brittle intermetallic compounds with nickel which are detrimental to the mechanical properties of brazed joints. The present investigation studied the microstructural evolution in nickel base brazes containing boron and/or silicon as melting point depressant(s) in simple systems using nickel as the base metal. The basic metallurgical reactions and formation of intermetallic compounds uncovered in these systems will be useful as a guide in predicting the evolution of microstructures in similar brazes in more complex systems involving base metals of nickel base superalloys. The four filler metal systems investigated in this study are: Ni-Cr-Si; Ni-Cr-B; Ni-Si-B and Ni-Cr-Fe-Si-B

Chemical formation of palladium-free surface-nickelized polyimide film for flexible electronics

International Nuclear Information System (INIS)

Hsiao, Y.-S.; Whang, W.-T.; Wu, S.-C.; Chuang, Kuen-Ru

2008-01-01

Flexible polyimide (PI) films for flexible electronics were surface-nickelized using a fully solution-based process and excellent adhesion between the nickel and polyimide phases was observed. Polyimide substrates were modified by alkaline hydrolysis, ion exchange, reduction and nickel electroless deposition without palladium. Atomic force microscopy and field emission scanning electron microscopy were used to follow the growth of nickel nanoparticles (Ni-NPs) and nickel layers on the polyimide surface. The surface resistances of the Ni-NPs/PI films and Ni/PI films, measured using a four-point probe, were 1.6 x 10 7 and 0.83 Ω/cm 2 , respectively. The thicknesses of Ni-NPs and the Ni layer on the polyimide surface were 82 nm and 382 nm, respectively, as determined by transmission electron microscopy, and the Ni layer adhered well to PI, as determined by the adhesive tape testing method

Super magnetic nanoparticles NiFe2O4, coated with aluminum-nickel oxide sol-gel lattices to safe, sensitive and selective purification of his-tagged proteins.

Science.gov (United States)

Mirahmadi-Zare, Seyede Zohreh; Allafchian, Alireza; Aboutalebi, Fatemeh; Shojaei, Pendar; Khazaie, Yahya; Dormiani, Kianoush; Lachinani, Liana; Nasr-Esfahani, Mohammad-Hossein

2016-05-01

Super magnetic nanoparticle NiFe2O4 with high magnetization, physical and chemical stability was introduced as a core particle which exhibits high thermal stability (>97%) during the harsh coating process. Instead of multi-stage process for coating, the magnetic nanoparticles was mineralized via one step coating by a cheap, safe, stable and recyclable alumina sol-gel lattice (from bohemite source) saturated by nickel ions. The TEM, SEM, VSM and XRD imaging and BET analysis confirmed the structural potential of NiFe2O4@NiAl2O4 core-shell magnetic nanoparticles for selective and sensitive purification of His-tagged protein, in one step. The functionality and validity of the nickel magnetic nanoparticles were attested by purification of three different bioactive His-tagged recombinant fusion proteins including hIGF-1, GM-CSF and bFGF. The bonding capacity of the nickel magnetics nanoparticles was studied by Bradford assay and was equal to 250 ± 84 μg Protein/mg MNP base on protein size. Since the metal ion leakage is the most toxicity source for purification by nickel magnetic nanoparticles, therefor the nickel leakage in purified final protein was determined by atomic absorption spectroscopy and biological activity of final purified protein was confirmed in comparison with reference. Also, in vitro cytotoxicity of nickel magnetic nanoparticles and trace metal ions were investigated by MTS assay analysis. The results confirmed that the synthesized nickel magnetic nanoparticles did not show metal ion toxicity and not affected on protein folding. Copyright © 2016 Elsevier Inc. All rights reserved.

Reducing agent (NaBH4) dependent structure, morphology and magnetic properties of nickel ferrite (NiFe2O4) nanorods

International Nuclear Information System (INIS)

Saravanakumar, B.; Rani, B. Jansi; Ravi, G.; Thambidurai, M.; Yuvakkumar, R.

2017-01-01

Nickel ferrite (Ni-Fe 2 O 4 ) nanorods were synthesized employing a simple chemical reduction method. Reducing agent (NaBH 4 ) influence on structural, morphological and magnetic properties of NiFe 2 O 4 nanorods was investigated. XRD results clearly revealed the presence of inverse cubic spinel nickel ferrite structure characteristic peaks and confirmed the site inversion of inverse spinel structure of Fe 3+ tetrahedral A site and Ni 2+ octahedral B site. The observed Raman characteristic peak at 488 and 683 cm −1 were corresponded to E 1 g and A 1 g mode whereas A and B site respectively corresponded to tetrahedral and octahedral site of NiFe 2 O 4 inverse spinel structure. The obtained PL peaks at 530 and 542 nm were attributed to the emission spectra of Fe 3+ ions in site A of inverse spinel structure and Ni 2+ ions in site B of inverse spinel structure respectively. SEM result clearly revealed that increase in NaBH 4 concentration had remarkable impact on nanorods formation, nano-octahedron structure, homogeneity and regularity of Ni-Ferrites. VSM studies clearly revealed the soft ferromagnetic nature of NiFe 2 O 4 and increase in NaBH 4 concentration further induced raise in metal cations concentration in A- and B- site which might impact the resultant magnetization of ferrites. - Highlights: • Nano rod formation has been initiated while increase of NaBH 4 concentration. • Further increasing NaBH 4 concentration favors nano-octahedron formation. • VSM studies revealed soft ferromagnetic nature of NiFe 2 O 4 .

Fatigue of orthodontic nickel-titanium (NiTi) wires in different fluids under constant mechanical stress

International Nuclear Information System (INIS)

Prymak, O.; Klocke, A.; Kahl-Nieke, B.; Epple, M.

2003-01-01

The aim of this study was to analyze in vitro the fatigue resistance of nickel-titanium (NiTi) and CuNiTi orthodontic wires when subjected to forces and fluids which are present intraorally. The wires were subjected to dynamic mechanical analysis (DMA) while they were immersed into different fluids with mechanical loading parameters similar to those that are subjected in the mouth. The characteristic temperatures of transitions and a rough surface structure on the perimeter of the wires were determined by differential scanning calorimetry (DSC) and scanning electron microscopy (SEM), respectively, before and after the DMA experiments. Stainless steel wires were used for comparison. In general, NiTi wires fractured earlier than the stainless steel specimens. Survival times were lower for the NiTi wires when immersed in fluids (water, citric acid, NaCl solution, artificial saliva, and fluoridated artificial saliva) than in air. SEM surface analysis showed that the NiTi and CuNiTi wires had a rougher surface than steel wires. The fracture occurred within a short number of loading cycles. Until fracture occurred, the mechanical properties remained mostly constant

Fatigue of orthodontic nickel-titanium (NiTi) wires in different fluids under constant mechanical stress

Energy Technology Data Exchange (ETDEWEB)

Prymak, O.; Klocke, A.; Kahl-Nieke, B.; Epple, M

2003-07-25

The aim of this study was to analyze in vitro the fatigue resistance of nickel-titanium (NiTi) and CuNiTi orthodontic wires when subjected to forces and fluids which are present intraorally. The wires were subjected to dynamic mechanical analysis (DMA) while they were immersed into different fluids with mechanical loading parameters similar to those that are subjected in the mouth. The characteristic temperatures of transitions and a rough surface structure on the perimeter of the wires were determined by differential scanning calorimetry (DSC) and scanning electron microscopy (SEM), respectively, before and after the DMA experiments. Stainless steel wires were used for comparison. In general, NiTi wires fractured earlier than the stainless steel specimens. Survival times were lower for the NiTi wires when immersed in fluids (water, citric acid, NaCl solution, artificial saliva, and fluoridated artificial saliva) than in air. SEM surface analysis showed that the NiTi and CuNiTi wires had a rougher surface than steel wires. The fracture occurred within a short number of loading cycles. Until fracture occurred, the mechanical properties remained mostly constant.

Internal carbonitriding behavior of Ni-V, Ni-Cr, and Ni-3Nb alloys

International Nuclear Information System (INIS)

Allen, A.T.; Douglass, D.L.

1999-01-01

Ni-2V, Ni-5V, Ni-12V, Ni-10Cr, Ni-20Cr, and Ni-3Nb alloys were carbonitrided in C 3 H 6 and NH 3 gas mixtures (bal H 2 ) over the range 700--1,000 C. Carbonitridation of Ni-12V and Ni-20Cr in C 3 H 6 /NH 3 /H 2 (1.5/1.5/97 v/o) and (1.5/10/88.5 v/o) produced duplex subscales consisting of near-surface nitrides with underlying carbides. Growth of each zone obeyed the parabolic rate law under most conditions. The presence of carbon generally did not effect the depth of the nitride zones compared to nitriding the alloys in NH 3 /H 2 (10/90 v/o). However, at 700 C, the nitride zones were deeper in the carbonitrided Ni-V alloys and Ni-20Cr. The presence of nitrogen generally increased the depth of the carbide zones in Ni-12V and Ni-20Cr compared to carburizing these alloys in C 3 H 6 /H 2 (1.5/98.5 v/o). VN, CrN, and NbN formed in Ni-V, Ni-Cr, and Ni-Nb alloys, respectively, whereas the underlying carbide layers contained V 4 C 3 in Ni-12V, Cr 3 C 2 above a zone of Cr 7 C 3 in Ni-20Cr, and NbC in Ni-3Nb. The solubilities and diffusivities of nitrogen and carbon in nickel were determined. Nitrogen and carbon each exhibited retrograde solubility with temperature in pure Ni in both carbonitriding environments. Nitrogen diffusion in nickel was generally lower in each carbonitriding mixture compared to nitrogen diffusion in a nitriding environment, except at 700 C when nitrogen diffusion was higher. Carbon diffusion in nickel was generally higher in the carbonitriding environments compared to carbon diffusion in a carburizing environment

Toxicity of nickel in the marine calanoid copepod Acartia tonsa: Nickel chloride versus nanoparticles.

Science.gov (United States)

Zhou, C; Vitiello, V; Casals, E; Puntes, V F; Iamunno, F; Pellegrini, D; Changwen, W; Benvenuto, G; Buttino, I

2016-01-01

Nickel compounds are widely used in industries and have been massively introduced in the environment in different chemical forms. Here we report the effect of two different chemical forms of nickel, NiCl2 and nickel nanoparticles (NiNPs), on the reproduction of the marine calanoid copepod Acartia tonsa. The behavior of nickel nanoparticles was analyzed with different techniques and with two protocols. In the "sonicated experiment" (SON) NiNP solution was sonicated while in the "non-sonicated experiment" (NON-SON) the solution was vigorously shaken by hand. Final nominal concentrations of 5, 10 and 50mgL(-1) and 1, 5 and 10mgL(-1) NiNPs were used for the acute and semichronic tests, respectively. Nanoparticle size did not change over time except for the highest concentration of 50mgL(-1) NiNPs, in which the diameter increased up to 843nm after 48h. The concentration of Ni dissolved in the water increased with NP concentration and was similar for SON and NON-SON solutions. Our results indicate that sonication does not modify toxicity for the copepod A. tonsa. Mean EC50 values were similar for NON-SON (20.2mgL(-1)) and SON experiments (22.14mgL(-1)) in the acute test. Similarly, no differences occurred between the two different protocols in the semichronic test, with an EC50 of 7.45mgL(-1) and 6.97mgL(-1) for NON-SON and SON experiments, respectively. Acute and semichronic tests, conducted exposing A. tonsa embryos to NiCl2 concentrations from 0.025 to 0.63mgL(-1), showed EC50 of 0.164 and 0.039mgL(-1), respectively. Overall, A. tonsa is more sensitive to NiCl2 than NiNPs with EC50 being one order of magnitude higher for NiNPs. Finally, we exposed adult copepods for 4 days to NiCl2 and NiNPs (chronic exposure) to study the effect on fecundity in terms of daily egg production and naupliar viability. Egg production is not affected by either form of nickel, whereas egg viability is significantly reduced by 0.025mgL(-1) NiCl2 and by 8.5mgL(-1) NiNPs. At NiNP concentration

Long life nickel electrodes for a nickel-hydrogen cell: Cycle life tests

Science.gov (United States)

Lim, H. S.; Verzwyvelt, S. A.

1985-01-01

In order to develop a long life nickel electrode for a Ni/H2 cell, the cycle life of nickel electrodes was tested in Ni/H2 boiler plate cells. A 19 test cell matrix was made of various nickel electrode designs including three levels each of plaque mechanical strength, median pore size of the plaque, and active material loading. Test cells were cycled to the end of their life (0.5v) in a 45 minute low Earth orbit cycle regime at 80% depth-of-discharge. It is shown that the active material loading level affects the cycle life the most with the optimum loading at 1.6 g/cc void. Mechanical strength does not affect the cycle life noticeably in the bend strength range of 400 to 700 psi. It is found that the best plaque is made of INCO nickel powder type 287 and has median pore size of 13 micron.

Ni(NH32(NO32—A 3-D Network through Bridging Nitrate Units Isolated from the Thermal Decomposition of Nickel Hexammine Dinitrate

Directory of Open Access Journals (Sweden)

Joachim Breternitz

2018-06-01

Full Text Available Nickel nitrate diammine, Ni(NH32(NO32, can be synthesised from the thermal decomposition of nickel nitrate hexammine, Ni[(NH36](NO32. The hexammine decomposes in two distinct major stages; the first releases 4 equivalents of ammonia while the second involves the release of NOx, N2, and H2O to yield NiO. The intermediate diammine compound can be isolated following the first deammoniation step or synthesised as a single phase from the hexammine under vacuum. Powder X-ray diffraction (PXD experiments have allowed the structure of Ni(NH32(NO32 to be solved for the first time. The compound crystallises in orthorhombic space group Pca21 (a = 11.0628 (5 Å, b = 6.0454 (3 Å, c = 9.3526 (4 Å; Z = 4 and contains 11 non-hydrogen atoms in the asymmetric unit. Fourier transform infrared (FTIR spectroscopy demonstrates that the bonding in the ammine is consistent with the structure determined by PXD.

Fe-solubility of Ni7S6 and Ni9S8: Thermodynamic analysis

International Nuclear Information System (INIS)

Waldner, P.

2011-01-01

Experimental data on phase equilibria have been used for thermodynamic analysis of the iron solubility of the nickel sulfides Ni 7 S 6 and Ni 9 S 8 . For both compounds, a two-sublattice approach within the framework of the compound energy formalism has been applied to perform Gibbs free energy modelling at 0.1 MPa total pressure consistently embedded in recent thermodynamic assessment studies of other iron-nickel-sulfides. The predicted maxima of iron solubility around 3 at% of Ni 7 S 6 and 5.5 at% of Ni 9 S 8 are confirmed by experimental data. The calculations of complex ternary phase relations with Fe-bearing Ni 7 S 6 and Ni 9 S 8 gain further improvement. The first internally consistent description of all thermodynamically stable phases known in the literature for the iron-nickel-sulfur system is completed.

Combination therapy of murine tumors with a degraded D-manno-D-glucan (DMG) from Microellobosporia grisea, and cyclophosphamide.

Science.gov (United States)

Nakajima, H; Hashimoto, S; Kita, Y; Takashi, T; Tsukada, W; Kohno, M; Ogawa, H; Abe, S; Mizuno, D

1983-12-01

DMG, a degraded D-manno-D-glucan with a host-mediated antitumor activity did not significantly enhance nor inhibit the development of suppressor cells for either the antibody-forming response or the delayed hypersensitivity reaction to sheep red blood cells. Cyclophosphamide (CY), which inhibited the generation of suppressor cells, was combined with DMG in treatment of murine syngeneic tumors to obtain a higher antitumor activity. The antitumor activity of the combination against MH134 hepatoma was synergistically higher than that of either component alone. A marked antitumor effect of the combination treatment against MM46 mammary carcinoma was also shown. High levels of antitumor delayed hypersensitivity reactions were observed with this combination therapy. The possible roles of DMG and CY in this combination therapy are discussed.

Oxidation characteristics of porous-nickel prepared by powder metallurgy and cast-nickel at 1273 K in air for total oxidation time of 100 h

Directory of Open Access Journals (Sweden)

Lamiaa Z. Mohamed

2017-11-01

Full Text Available The oxidation behavior of two types of inhomogeneous nickel was investigated in air at 1273 K for a total oxidation time of 100 h. The two types were porous sintered-nickel and microstructurally inhomogeneous cast-nickel. The porous-nickel samples were fabricated by compacting Ni powder followed by sintering in vacuum at 1473 K for 2 h. The oxidation kinetics of the samples was determined gravimetrically. The topography and the cross-section microstructure of each oxidized sample were observed using optical and scanning electron microscopy. X-ray diffractometry and X-ray energy dispersive analysis were used to determine the nature of the formed oxide phases. The kinetic results revealed that the porous-nickel samples had higher trend for irreproducibility. The average oxidation rate for porous- and cast-nickel samples was initially rapid, and then decreased gradually to become linear. Linear rate constants were 5.5 × 10−8 g/cm2 s and 3.4 × 10−8 g/cm2 s for the porous- and cast-nickel samples, respectively. Initially a single-porous non-adherent NiO layer was noticed on the porous- and cast-nickel samples. After a longer time of oxidation, a non-adherent duplex NiO scale was formed. The two layers of the duplex scales were different in color. NiO particles were observed in most of the pores of the porous-nickel samples. Finally, the linear oxidation kinetics and the formation of porous non-adherent duplex oxide scales on the inhomogeneous nickel substrates demonstrated that the addition of new layers of NiO occurred at the scale/metal interface due to the thermodynamically possible reaction between Ni and the molecular oxygen migrating inwardly.

Oxidation characteristics of porous-nickel prepared by powder metallurgy and cast-nickel at 1273 K in air for total oxidation time of 100 h.

Science.gov (United States)

Mohamed, Lamiaa Z; Ghanem, Wafaa A; El Kady, Omayma A; Lotfy, Mohamed M; Ahmed, Hafiz A; Elrefaie, Fawzi A

2017-11-01

The oxidation behavior of two types of inhomogeneous nickel was investigated in air at 1273 K for a total oxidation time of 100 h. The two types were porous sintered-nickel and microstructurally inhomogeneous cast-nickel. The porous-nickel samples were fabricated by compacting Ni powder followed by sintering in vacuum at 1473 K for 2 h. The oxidation kinetics of the samples was determined gravimetrically. The topography and the cross-section microstructure of each oxidized sample were observed using optical and scanning electron microscopy. X-ray diffractometry and X-ray energy dispersive analysis were used to determine the nature of the formed oxide phases. The kinetic results revealed that the porous-nickel samples had higher trend for irreproducibility. The average oxidation rate for porous- and cast-nickel samples was initially rapid, and then decreased gradually to become linear. Linear rate constants were 5.5 × 10 -8  g/cm 2  s and 3.4 × 10 -8  g/cm 2  s for the porous- and cast-nickel samples, respectively. Initially a single-porous non-adherent NiO layer was noticed on the porous- and cast-nickel samples. After a longer time of oxidation, a non-adherent duplex NiO scale was formed. The two layers of the duplex scales were different in color. NiO particles were observed in most of the pores of the porous-nickel samples. Finally, the linear oxidation kinetics and the formation of porous non-adherent duplex oxide scales on the inhomogeneous nickel substrates demonstrated that the addition of new layers of NiO occurred at the scale/metal interface due to the thermodynamically possible reaction between Ni and the molecular oxygen migrating inwardly.

Nickel and cobalt base alloys

International Nuclear Information System (INIS)

Houlle, P.

1994-01-01

Nickel base alloys have a good resistance to pitting, cavernous or cracks corrosion. Nevertheless, all the nickel base alloys are not equivalent. Some differences exit between all the families (Ni, Ni-Cu, Ni-Cr-Fe, Ni-Cr-Fe-Mo/W-Cu, Ni-Cr-Mo/W, Ni-Mo). Cobalt base alloys in corrosive conditions are generally used for its wear and cracks resistance, with a compromise to its localised corrosion resistance properties. The choice must be done from the perfect knowledge of the corrosive medium and of the alloys characteristics (chemical, metallurgical). A synthesis of the corrosion resistance in three medium (6% FeCl 3 , 4% NaCl + 1% HCl + 0.1% Fe 2 (SO 4 ) 3 , 11.5% H 2 SO 4 + 1.2% HCl + 1% Fe 2 (SO 4 ) 3 + 1% CuCl 2 ) is presented. (A.B.). 11 refs., 1 fig., 12 tabs

Bulk diffusion and solubility of silver and nickel in lead, lead-silver and lead-nickel solid solutions

International Nuclear Information System (INIS)

Amenzou-Badrour, H.; Moya, G.; Bernardini, J.

1988-01-01

The results of a study of solubility and bulk diffusion of /sup 110/Ag and /sup 63/Ni in lead, lead-silver and lead-nickel solid solutions in the temperature range 220 to 88 0 C are reported. Owing to the low solubility of silver and nickel in lead, Fick's solution corresponding to the boundary condition of a constant concentration of solute at the surface has been used. Depth profile concentration analysis suggests a fundamental difference between the diffusion mechanisms of silver and nickel. Since silver penetration profiles in pure lead give diffusion coefficients independent of the penetration depth and silver concentration, it is suggested that slight decreases of silver diffusivity in lead-silver solid solutions have no significance. This implies that the interstitial silver atoms do not associate significantly with each other to form Ag-Ag dimers. In contrast, different behaviors of /sup 63/Ni depth profile concentration in pure lead and saturated PbNi solid solutions agree with a Ni-Ni interaction leading to the formation of less mobile dimers near the surface in pure lead

Atomistic calculations of hydrogen interactions with Ni3Al grain boundaries and Ni/Ni3Al interfaces

International Nuclear Information System (INIS)

Baskes, M.I.; Angelo, J.E.; Moody, N.R.

1995-01-01

Embedded Atom Method (EAM) potentials have been developed for the Ni/Al/H system. The potentials have been fit to numerous properties of this system. For example, these potentials represent the structural and elastic properties of bulk Ni, Al, Ni 3 Al, and NiAl quite well. In addition the potentials describe the solution and migration behavior of hydrogen in both nickel and aluminum. A number of calculations using these potentials have been performed. It is found that hydrogen strongly prefers sites in Ni 3 Al that are surrounded by 6 Ni atoms. Calculations of the trapping of hydrogen to a number of grain boundaries in Ni 3 Al have been performed as a function of hydrogen chemical potential at room temperature. The failure of these bicrystals under tensile stress has been examined and will be compared to the failure of pure Ni 3 Al boundaries. Boundaries containing a preponderance of nickel are severely weakened by hydrogen. In order to investigate the potential embrittlement of γ/γ' alloys, trapping of hydrogen to a spherical Ni 3 Al precipate in nickel as a function of chemical potential at room temperature has been calculated. It appears that the boundary is not a strong trap for hydrogen, hence embrittlement in these alloys is not primarily due to interactions of hydrogen with the γ/γ interface

New insights on the mechanisms controlling the nickel dependence of swelling in irradiated Fe-Cr-Ni alloys

International Nuclear Information System (INIS)

Hoyt, J.J.; Garner, F.A.

1990-01-01

In a previous report the interstitial and vacancy biases for an edge dislocation in a binary alloy were examined, assuming the existence of an equilibrium Cottrel atmosphere around the line defect. The Larche' and Cahn treatment of stress relaxation due to a solute atmosphere was employed with the Wolfer and Ashkin formulation for the bias of an edge dislocation to compute the bias as a function of nickel concentration in the Fe-Ni system. Using the minimum critical void radius concept, the concentration-dependent bias was shown to offer a plausible explanation for the minimum in swelling observed at intermediate nickel levels and the gradual increase in swelling at higher nickel levels. In this report, a more realistic description of the composition dependence of vacancy diffusion has also been included, an addition which improves the model substantially. 18 refs., 8 figs

Oxidation resistance of nickel alloys at high temperature

International Nuclear Information System (INIS)

Tyuvin, Yu.D.; Rogel'berg, I.L.; Ryabkina, M.M.; Plakushchaya, A.F.

1977-01-01

The heat resistance properties of nickel alloys Ni-Cr-Si, Ni-Si-Al, Ni-Si-Mn and Ni-Al-Mn have been studied by the weight method during oxidation in air at 1000 deg and 1200 deg C. It is demonstrated that manganese reduces the heat resistance properties of Ni-Si and Ni-Al alloys, whilst the addition of over 3% aluminium enhances the heat resistance properties of Ni-Si (over 1.5%) alloys. The maximum heat resistance properties are shown by Ni-Si-Al and Ni-Cr-Si alloys with over 2% Si. These alloys offer 3 to 4 times better oxidation resistance as compared with pure nickel at 1000 deg C and 10 times at 1200 deg C

Electrochemical behavior of heavily cycled nickel electrodes in Ni/H2 cells containing electrolytes of various KOH concentrations

Science.gov (United States)

Lim, H. S.; Verzwyvelt, S. A.

1989-01-01

A study has been made of charge and discharge voltage changes with cycling of Ni/H2 cells containing electrolytes of various KOH concentrations. A study has also been made of electrochemical behavior of the nickel electrodes from the cycled Ni/H2 cells as a function of overcharge amounts. Discharge voltages depressed gradually with cycling for cells having high KOH concentrations (31 to 36 percent), but the voltages increased for those having low KOH concentrations (21 to 26 percent). To determine if there was a crystallographic change of the active material due to cycling, electrochemical behavior of nickel electrodes was studied in an electrolyte flooded cell containing either 31 or 26 percent KOH electrolyte as a function of the amount of overcharge. The changes in discharge voltage appear to indicate crystal structure changes of active material from gamma-phase to beta-phase in low KOH concentrations, and vice versa in high KOH concentration.

Theoretical study of the binding nature of glassy carbon with nickel(II) phthalocyanine complexes

International Nuclear Information System (INIS)

Cortez, Luis; Berrios, Cristhian; Yanez, Mauricio; Cardenas-Jiron, Gloria I.

2009-01-01

A theoretical study at the semiempirical RHF/PM3(tm) level (tm: transition metal) of the binding nature between a glassy carbon (GC) cluster and a nickel(II) complex (nickel(II) phthalocyanine NiPc, nickel(II) tetrasulphophthalocyanine NiTSPc) was performed. Three types of interactions for GC...NiPc (NiTSPc) were studied: (a) through an oxo (O) bridge, (b) through an hydroxo (OH) bridge, and (c) non-bridge. One layer (NiPc, NiTSPc) and two layers (NiPc...NiPc) of complex were considered. The binding energy calculated showed that in both cases NiPc and NiTSPc, the oxo structures are more stable than the hydroxo ones, and than the non-bridge systems. Charge analysis (NAO) predicted that GC gained more electrons in an oxo structure than in the analogues hydroxo. The theoretical results showed an agreement with the experimental data available, an oxo binding between GC and a nickel complex (NiPc, NiTSPc) in aqueous alkaline solutions is formed.

Theoretical study of the binding nature of glassy carbon with nickel(II) phthalocyanine complexes

Energy Technology Data Exchange (ETDEWEB)

Cortez, Luis [Laboratorio de Quimica Teorica, Facultad de Quimica y Biologia, Universidad de Santiago de Chile (USACH), Casilla 40, Correo 33, Santiago (Chile); Berrios, Cristhian [Laboratorio de Electrocatalisis, Facultad de Quimica y Biologia, Universidad de Santiago de Chile (USACH), Casilla 40, Correo 33, Santiago (Chile); Yanez, Mauricio [Laboratorio de Recursos Renovables, Centro de Biotecnologia, Universidad de Concepcion, Casilla-160 C, Concepcion (Chile); Cardenas-Jiron, Gloria I., E-mail: gloria.cardenas@usach.cl [Laboratorio de Quimica Teorica, Facultad de Quimica y Biologia, Universidad de Santiago de Chile (USACH), Casilla 40, Correo 33, Santiago (Chile)

2009-11-26

A theoretical study at the semiempirical RHF/PM3(tm) level (tm: transition metal) of the binding nature between a glassy carbon (GC) cluster and a nickel(II) complex (nickel(II) phthalocyanine NiPc, nickel(II) tetrasulphophthalocyanine NiTSPc) was performed. Three types of interactions for GC...NiPc (NiTSPc) were studied: (a) through an oxo (O) bridge, (b) through an hydroxo (OH) bridge, and (c) non-bridge. One layer (NiPc, NiTSPc) and two layers (NiPc...NiPc) of complex were considered. The binding energy calculated showed that in both cases NiPc and NiTSPc, the oxo structures are more stable than the hydroxo ones, and than the non-bridge systems. Charge analysis (NAO) predicted that GC gained more electrons in an oxo structure than in the analogues hydroxo. The theoretical results showed an agreement with the experimental data available, an oxo binding between GC and a nickel complex (NiPc, NiTSPc) in aqueous alkaline solutions is formed.

Microstructure and properties of nickel base superalloy joints brazed with Ni-Cr-Co-B and BNi-1a filler metals

Energy Technology Data Exchange (ETDEWEB)

Zhuang, H. [Beijing Univ. of Aeronautics and Astronautics (China); Liu, W. [Dalian Railway Inst. (China). Welding Div.

1995-12-31

In this study, the kind and compositions of brittle phases formed in joints of a nickel-base superalloy brazed with the Ni-Cr-Co-B and BNi-1a (Ni-Cr-B-Si) filler metals were investigated. Their brittle-phase-free maximum brazing clearances (MBC) were characterized in dependence on the brazing conditions. The improvement on joint structures by post-braze heat treatment was also examined. (orig./MM)

Linear thermal expansion coefficient of cast Fe-Ni invar and Fe-Ni-Co superinvar alloys

International Nuclear Information System (INIS)

Ogorodnikova, O.M.; Chermenskaya, E.V.; Rabinovich, S.V.; Grachev, S.V.

1999-01-01

Cast invar alloys Fe-Ni (28-35 wt. % Ni) are investigated using metallography, dilatometry and X-ray methods as soon as the crystallization is completed and again after low-temperature treatment resulting in martensitic transformation in low nickel alloys. Nickel distribution in a cast superinvar Fe-32% Ni-4% Co is studied by means of X-ray spectrum microanalysis. The results obtained permit the correction of model concepts about cast invars and the estimate of a coefficient of linear expansion depending on phase composition and nickel microsegregation [ru

Nickel in silicon: Room-temperature in-diffusion and interaction with radiation defects

Energy Technology Data Exchange (ETDEWEB)

Yarykin, Nikolai [Institute of Microelectronics Technology, RAS, Chernogolovka (Russian Federation); Weber, Joerg [Technische Universitaet Dresden (Germany)

2017-07-15

Nickel is incorporated into silicon wafers during chemomechanical polishing in an alkaline Ni-contaminated slurry at room temperature. The nickel in-diffusion is detected by DLTS depth profiles of a novel Ni{sub 183} level, which is formed due to a reaction between the diffusing nickel and the VO centers introduced before the polishing. The Ni{sub 183} profile extends up to 10 μm after a 2 min polishing. The available data provide a lower estimate for the room-temperature nickel diffusivity D{sub Ni} > 10{sup -9} cm{sup 2} s{sup -1}. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

THE EFFECT OF SINGLE NICKEL AND COMBINED NICKEL AND ZINC PERORAL ADMINISTRATION ON HAEMATOLOGICAL PARAMETERS IN RABBITS

Directory of Open Access Journals (Sweden)

Jana Emrichová

2013-06-01

Full Text Available The aim of this study was to determine the effect of single nickel (NiCl2 and nickel in combination with zinc (ZnCl2 on selected haematological parameters of rabbits: white blood cell, red blood cell, haemoglobin, haematocrit, mean corpuscular volume, mean corpuscular haemoglobin, mean corpuscular haemoglobin concentration, platelets, mean platelet volume, red cell distribution width, lymphocytes, monocytes, eosinophils, neutrophils, basophils. Twenty rabbits of broiler line Californian were used in this experiment. The animals were divided into the five groups, four animals in each ones (control group K and experimental groups E1, E2, E3 and E4. Animals were fed ad libitum using KKV1 feeding mixture (FM with or without nickel and zinc addition for 90 days follows: group E1 received 17.5 g of NiCl2.100 kg-1 FM; group E2 35 g NiCl2.100 kg-1 FM; group E3 17.5 g NiCl2 + 30 g ZnCl2.100 kg-1 FM and group E4 35 g NiCl2 + 30 g ZnCl2.100 kg-1 FM. The parameters were analysed using Advia – 120. Blood was collected into tubes containing anticoagulant agents K – EDTA. Statistical analyse showed a significant changes (P 0.05. Nickel has negative effect on some haematological parameters, but zinc can eliminates its influence.

Three-dimensional interconnected nickel phosphide networks with hollow microstructures and desulfurization performance

International Nuclear Information System (INIS)

Zhang, Shuna; Zhang, Shujuan; Song, Limin; Wu, Xiaoqing; Fang, Sheng

2014-01-01

Graphical abstract: Three-dimensional interconnected nickel phosphide networks with hollow microstructures and desulfurization performance. - Highlights: • Three-dimensional Ni 2 P has been prepared using foam nickel as a template. • The microstructures interconnected and formed sponge-like porous networks. • Three-dimensional Ni 2 P shows superior hydrodesulfurization activity. - Abstract: Three-dimensional microstructured nickel phosphide (Ni 2 P) was fabricated by the reaction between foam nickel (Ni) and phosphorus red. The as-prepared Ni 2 P samples, as interconnected networks, maintained the original mesh structure of foamed nickel. The crystal structure and morphology of the as-synthesized Ni 2 P were characterized by X-ray diffraction, scanning electron microscopy, automatic mercury porosimetry and X-ray photoelectron spectroscopy. The SEM study showed adjacent hollow branches were mutually interconnected to form sponge-like networks. The investigation on pore structure provided detailed information for the hollow microstructures. The growth mechanism for the three-dimensionally structured Ni 2 P was postulated and discussed in detail. To investigate its catalytic properties, SiO 2 supported three-dimensional Ni 2 P was prepared successfully and evaluated for the hydrodesulfurization (HDS) of dibenzothiophene (DBT). DBT molecules were mostly hydrogenated and then desulfurized by Ni 2 P/SiO 2

Structural characterization of nickel oxide/hydroxide nanosheets produced by CBD technique

Energy Technology Data Exchange (ETDEWEB)

Taşköprü, T., E-mail: ttaskopru@anadolu.edu.tr [Department of Physics, Anadolu University, Eskişehir 26470 (Turkey); Department of Physics, Çankırı Karatekin University, Çankırı 18100 (Turkey); Zor, M.; Turan, E. [Department of Physics, Anadolu University, Eskişehir 26470 (Turkey)

2015-10-15

Graphical abstract: SEM images of (a) as deposited β-Ni(OH)2 and (b) NiO samples deposited with pH 10 solution. The inset figures shows the absorbance spectra of (a) β-Ni(OH)2 and (b) NiO samples. - Highlights: • The formation of β-Ni(OH){sub 2} and NiO were confirmed with XRD, SEM, FT-IR and Raman. • Porous nickel oxide was synthesized after heat treatment of nickel hydroxide. • The increase in pH value changes the nanoflake structure to hexagonal nanosheet. • On increasing the pH from 8 to 11, the band gap decreases from 3.52 to 3.37 eV. - Abstract: Nickel hydroxide samples were deposited onto glass substrates using Ni(NO{sub 3}){sub 2}·6H{sub 2}O and aqueous ammonia by chemical bath deposition technique. The influence of pH of solution was investigated by means of X-ray diffraction, field emission scanning electron microscopy, Fourier transform infrared, Raman spectroscopy, optical absorption and BET analysis. The as-deposited samples were identified as β-Ni(OH){sub 2}, were transformed into NiO after heat treatment in air at 500 °C for 2 h. Porous nickel oxide nanosheets are obtained by heating nickel hydroxide nanosheets. The optical transitions observed in the absorbance spectra below optical band gap is due to defects or Ni{sup 2+} vacancies in NiO samples. The band gap energy of NiO samples changes between 3.37 and 3.52 eV depending on the pH values.

Length-dependent corrosion behavior, Ni2+ release, cytocompatibility, and antibacterial ability of Ni-Ti-O nanopores anodically grown on biomedical NiTi alloy.

Science.gov (United States)

Hang, Ruiqiang; Liu, Yanlian; Bai, Long; Zhang, Xiangyu; Huang, Xiaobo; Jia, Husheng; Tang, Bin

2018-08-01

In the present work, nickel-titanium-oxygen nanopores with different length (0.55-114 μm) were anodically grown on nearly equiatomic nickel-titanium (NiTi) alloy. Length-dependent corrosion behavior, nickel ion (Ni 2+ ) release, cytocompatibility, and antibacterial ability were investigated by electrochemical, analytical chemistry, and biological methods. The results show constructing nanoporous structure on the NiTi alloy improve its corrosion resistance. However, the anodized samples release more Ni 2+ than that of the bare NiTi alloy, suggesting chemical dissolution of the nanopores rather than electrochemical corrosion governs the Ni 2+ release. In addition, the Ni 2+ release amount increases with nanopore length. The anodized samples show good cytocompatibility when the nanopore length is covers the one (1-11 μm) that the nanopores showing favorable antibacterial ability. Consequently, the nanopores with length in the range of 1-11 μm are promising as coatings of biomedical NiTi alloy for anti-infection, drug delivery, and other desirable applications. Copyright © 2018 Elsevier B.V. All rights reserved.

Giant Negative Piezoresistive Effect in Diamond-like Carbon and Diamond-like Carbon-Based Nickel Nanocomposite Films Deposited by Reactive Magnetron Sputtering of Ni Target

DEFF Research Database (Denmark)

Meškinis, Šaru Nas; Gudaitis, Rimantas; Šlapikas, Kęstutis

2018-01-01

deposited by either reactive HIPIMS or dc magnetron sputtering of Ni target was explained by possible clustering of the sp2-bonded carbon and/or formation of areas with the decreased hydrogen content. It was suggested that the tensile stress-induced rearrangements of these conglomerations have resulted......Piezoresistive properties of hydrogenated diamond-like carbon (DLC) and DLC-based nickel nanocomposite (DLC:Ni) films were studied in the range of low concentration of nickel nanoparticles. The films were deposited by reactive high power pulsed magnetron sputtering (HIPIMS) of Ni target, and some...... samples were deposited by direct current (dc) reactive magnetron sputtering for comparison purposes. Raman scattering spectroscopy, energy-dispersive X-ray spectrometry (EDS), and X-ray photoelectron spectroscopy (XPS) were used to study the structure and chemical composition of the films. A four...

On the rational alloying of structural chromium-nickel steels

International Nuclear Information System (INIS)

Astaf'ev, A.A.

1982-01-01

A study was made on the influence of chromium nickel, phosphorus on the critical brittleness temperature of Cr-Ni-Mo-V structural steels. It is shown that the critical brittleness temperature of these steels increases at chromium content more over than 2% and nickel content more than 2% in the result of carbide transformations during tempering. Increase of nickel content in Cr-Ni-Mo-V-steels strengthens the tendency to embrittlement during slow cooling, from tempering temperature owing to development of process of phosphorus grain-boundary segregation. Two mentioned mechanisms of embrittlement determine principles of rational steel alloying. The extreme dependence of the critical brittleness temperature on chromium and nickel content, which enables to choose the optimum composition of Cr-Ni-Mo-V-steels, was established

Synthesis, structure characterization and catalytic activity of nickel tungstate nanoparticles

International Nuclear Information System (INIS)

Pourmortazavi, Seied Mahdi; Rahimi-Nasrabadi, Mehdi; Khalilian-Shalamzari, Morteza; Zahedi, Mir Mahdi; Hajimirsadeghi, Seiedeh Somayyeh; Omrani, Ismail

2012-01-01

Graphical abstract: NiWO 4 nanoparticles were prepared via precipitation technique. Experimental parameters of procedure were optimized statistically. Highlights: ► NiWO 4 spherical nanoparticles were synthesized via direct precipitation method. ► Taguchi robust design was used for optimization of synthesis reaction parameters. ► Composition and structural properties of NiWO 4 nanoparticles were characterized. ► EDAX, XRD, SEM, FT-IR, UV–vis and photoluminescence techniques were employed. ► Catalytic activity of the product in a cyclo-addition reaction was investigated. - Abstract: Taguchi robust design was applied to optimize experimental parameters for controllable, simple and fast synthesis of nickel tungstate nanoparticles. NiWO 4 nanoparticles were synthesized by precipitation reaction involving addition of nickel ion solution to the tungstate aqueous reagent and then formation of nickel tungstate nucleolus which are insoluble in aqueous media. Effects of various parameters such as nickel and tungstate concentrations, flow rate of reagent addition and reactor temperature on diameter of synthesized nickel tungstate nanoparticles were investigated experimentally by the aid of orthogonal array design. The results for analysis of variance (ANOVA) showed that particle size of nickel tungstate can be effectively tuned by controlling significant variables involving nickel and tungstate concentrations and flow rate; while, temperature of the reactor has a no considerable effect on the size of NiWO 4 particles. The ANOVA results proposed the optimum conditions for synthesis of nickel tungstate nanoparticles via this technique. Also, under optimum condition nanoparticles of NiWO 4 were prepared and their structure and chemical composition were characterized by means of EDAX, XRD, SEM, FT-IR spectroscopy, UV–vis spectroscopy, and photoluminescence. Finally, catalytic activity of the nanoparticles in a cycloaddition reaction was examined.

Synthesis, structure characterization and catalytic activity of nickel tungstate nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Pourmortazavi, Seied Mahdi, E-mail: pourmortazavi@yahoo.com [Faculty of Material and Manufacturing Technologies, Malek Ashtar University of Technology, Tehran (Iran, Islamic Republic of); Rahimi-Nasrabadi, Mehdi, E-mail: rahiminasrabadi@gmail.com [Department of Chemistry, Imam Hossein University, Tehran (Iran, Islamic Republic of); Khalilian-Shalamzari, Morteza [Department of Chemistry, Imam Hossein University, Tehran (Iran, Islamic Republic of); Zahedi, Mir Mahdi; Hajimirsadeghi, Seiedeh Somayyeh [Islamic Azad University, Varamin Pishva Branch, Varamin (Iran, Islamic Republic of); Omrani, Ismail [Department of Chemistry, Imam Hossein University, Tehran (Iran, Islamic Republic of)

2012-12-15

Graphical abstract: NiWO{sub 4} nanoparticles were prepared via precipitation technique. Experimental parameters of procedure were optimized statistically. Highlights: Black-Right-Pointing-Pointer NiWO{sub 4} spherical nanoparticles were synthesized via direct precipitation method. Black-Right-Pointing-Pointer Taguchi robust design was used for optimization of synthesis reaction parameters. Black-Right-Pointing-Pointer Composition and structural properties of NiWO{sub 4} nanoparticles were characterized. Black-Right-Pointing-Pointer EDAX, XRD, SEM, FT-IR, UV-vis and photoluminescence techniques were employed. Black-Right-Pointing-Pointer Catalytic activity of the product in a cyclo-addition reaction was investigated. - Abstract: Taguchi robust design was applied to optimize experimental parameters for controllable, simple and fast synthesis of nickel tungstate nanoparticles. NiWO{sub 4} nanoparticles were synthesized by precipitation reaction involving addition of nickel ion solution to the tungstate aqueous reagent and then formation of nickel tungstate nucleolus which are insoluble in aqueous media. Effects of various parameters such as nickel and tungstate concentrations, flow rate of reagent addition and reactor temperature on diameter of synthesized nickel tungstate nanoparticles were investigated experimentally by the aid of orthogonal array design. The results for analysis of variance (ANOVA) showed that particle size of nickel tungstate can be effectively tuned by controlling significant variables involving nickel and tungstate concentrations and flow rate; while, temperature of the reactor has a no considerable effect on the size of NiWO{sub 4} particles. The ANOVA results proposed the optimum conditions for synthesis of nickel tungstate nanoparticles via this technique. Also, under optimum condition nanoparticles of NiWO{sub 4} were prepared and their structure and chemical composition were characterized by means of EDAX, XRD, SEM, FT-IR spectroscopy, UV

Early stages of oxidation of ion-implanted nickel at high temperature

International Nuclear Information System (INIS)

Peide, Z.; Grant, W.A.; Procter, R.P.M.

1981-01-01

The early stages of oxidation of nickel implanted with nickel, chromium, or lithium ions in oxygen at 1100 0 C have been studied using various electron-optical techniques. The unimplanted metal develops initially a fine-grained, convoluted scale having a ridged, cellular structure. Subsequently, the oxide grains increase in size significantly and oxidation becomes predominantly controlled by diffusion of Ni /sup 2+/ ions across a compact, columnar scale. Implantation of the surface with nickel ions has no significant effect on the initial oxidation behavior. However, after implantation with chromium or lithium ions, the development of the NiO scale is, in the early stages of oxidation, suppressed by formation of NiCr 2 O 4 or LiO 2 nodules, respectively. Subsequently, the implanted species are incorporated into the steady-state NiO scale where they dope the oxide and thus influence the diffusion rate of Ni /sup 2+/ ions through it. As would be predicted, the steady-state oxidation rate of chromium-implanted nickel is increased while that of lithium- implanted nickel is decreased compared with that of the unimplanted metal

Development of a Fe-Ni battery for electric vehicle use. Denki jidoshayo tetsu nickel denchi no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Onozuka, T.; Okuda, K. (The Tohoku Electric Power Co. Inc., Sendai (Japan))

1993-08-11

Development has been made on an iron-nickel battery as a low polluting electric vehicle battery that is superior in low-temperature performance to lead-acid batteries. This paper summarizes the battery. The battery uses NiOOH for positive electrodes, Fe for negative electrodes, and alkaline aqueous solution for electrolyte. The battery was manufactured in the following manners to make it suit the electric vehicle application: The iron electrode was manufactured by mixing reduced iron powder having grain sizes from 5[mu] to 6[mu] with electrolyzed iron powder with grain sizes from 20[mu] to 30[mu] in a bonding agent, and sintered at temperatures from 750[degree]C to 800[degree]C in H2 atmosphere; iron electrodes that have superior life and material utilization factor were found to have reduced iron powder ratios from 20% to 30%; the nickel electrode consists of a substrate obtained by coating metallic Ni powder on a sheet and sintering it and filling it with NiOH; the electrolyte is composed of KOH containing LiOH and KS; the separator uses a ribbed PVC porous sheet; the container is made of PP; performance evaluation tests were conducted on discharge performance, energy density, output density, temperature characteristics, charge efficiency, and cycle life; and the results of vehicle driving tests surpassed those from lead-acid batteries. 6 refs., 18 figs., 6 tabs.

Nickel nanostructured materials from liquid phase photodeposition

International Nuclear Information System (INIS)

Giuffrida, Salvatore; Condorelli, Guglielmo G.; Costanzo, Lucia L.; Ventimiglia, Giorgio; Nigro, Raffaella Lo; Favazza, Maria; Votrico, Enrico; Bongiorno, Corrado; Fragala, Ignazio L.

2007-01-01

Liquid Phase Photo-Deposition (LPPD) technique has been used to obtain both colloidal particles and thin films of metallic and chloride nickel from solutions of only precursor Ni(acac) 2 (acac=2,4-pentandionato). Metallic nickel was obtained from ethanol solutions by direct nickel(II) photoreduction at 254 nm and by acetone sensitised reaction at 300 nm. In this latter process the rate was higher than in the first one. NiCl 2 was formed from CCl 4 solution by a solvent-initiated reaction. TEM analysis, performed on colloidal particles of nickel, showed that their dimensions are in the range 2-4 nm. The films did not present carbon contamination and were characterized by AFM, XPS and GIXRD. Metallic films consisted of particles of 20-40 nm that are the result of the aggregation of smaller crystallites (4-5 nm). Larger agglomerations (around 200 nm) have been observed for NiCl 2 films

Nickel nanostructured materials from liquid phase photodeposition

Energy Technology Data Exchange (ETDEWEB)

Giuffrida, Salvatore, E-mail: sgiuffrida@unict.it; Condorelli, Guglielmo G.; Costanzo, Lucia L.; Ventimiglia, Giorgio [Universita degli Studi di Catania and INSTM UdR di, Dipartimento di Scienze Chimiche (Italy); Nigro, Raffaella Lo [IMM-CNR (Italy); Favazza, Maria; Votrico, Enrico [Universita degli Studi di Catania and INSTM UdR di, Dipartimento di Scienze Chimiche (Italy); Bongiorno, Corrado [IMM-CNR (Italy); Fragala, Ignazio L. [Universita degli Studi di Catania and INSTM UdR di, Dipartimento di Scienze Chimiche (Italy)

2007-08-15

Liquid Phase Photo-Deposition (LPPD) technique has been used to obtain both colloidal particles and thin films of metallic and chloride nickel from solutions of only precursor Ni(acac){sub 2} (acac=2,4-pentandionato). Metallic nickel was obtained from ethanol solutions by direct nickel(II) photoreduction at 254 nm and by acetone sensitised reaction at 300 nm. In this latter process the rate was higher than in the first one. NiCl{sub 2} was formed from CCl{sub 4} solution by a solvent-initiated reaction. TEM analysis, performed on colloidal particles of nickel, showed that their dimensions are in the range 2-4 nm. The films did not present carbon contamination and were characterized by AFM, XPS and GIXRD. Metallic films consisted of particles of 20-40 nm that are the result of the aggregation of smaller crystallites (4-5 nm). Larger agglomerations (around 200 nm) have been observed for NiCl{sub 2} films.

Microwave irradiation and citric acid assisted seed germination and phytoextraction of nickel (Ni) by Brassica napus L.: morpho-physiological and biochemical alterations under Ni stress.

Science.gov (United States)

Farid, Mujahid; Ali, Shafaqat; Rizwan, Muhammad; Saeed, Rashid; Tauqeer, Hafiz Muhammad; Sallah-Ud-Din, Rasham; Azam, Ahmed; Raza, Nighat

2017-09-01

The complex bio-geochemistry of soil allows pollutant to persist for a longer period of time which further decreased the fertility and natural composition of land. Nickel, an inorganic pollutant, coming from a wide range of industrial and manufacturing units possesses serious threat to soil degradation and crop productivity around the world. The present study was carried to evaluate the combined role of microwave irradiation (MR) and citric acid (CA) on the phytoextraction potential of Brassica napus L. under Ni stress. An initial seed germination test was conducted to select effective time scale of MR exposure. Highest seed germination was observed at exposure of 2.45 GHz frequency for 30 s. Healthy seeds of B. napus L. genotype Faisal Canola (RBN-03060) treated with MR at 2.45 GHz for 30 s were sown in plastic pots filled with 5 kg of soil. Nickel and CA applied exogenously in solution form with different combinations to both MR-treated and untreated B. napus plants. The MR-treated plants showed higher growth, biomass, photosynthetic pigments (Chl a, b, total, and carotenoids) and activities of antioxidant enzymes (SOD, POD, APX, CAT) as compared to untreated plants who showed higher reactive oxygen species (MDA, H 2 O 2 ) and electrolyte leakage. Increasing Ni concentration significantly decreased the physiological and biochemical attributes of B. napus both in MR-treated and untreated plants. The addition of CA alleviated Ni-induced toxic effects in both MR-treated and untreated plants by improving antioxidant defense system. The degree of Ni stress mitigation was higher in MR-treated plants. The Ni concentration was higher in root, stem, and leaves of MR-treated plants under CA application as compared to untreated plants. The present study concluded that seeds treated with MR before sowing showed higher accumulation and concentration of Ni from soil, and this phenomenon boosted with the application of CA.

Enhancement of porous silicon photoluminescence by electroless deposition of nickel

Energy Technology Data Exchange (ETDEWEB)

Amdouni, S. [Unité de nanomatériaux et photonique, Université El Manar, Faculté des Sciences de Tunis, Département de Physique, 2092 El Manar, Tunis Tunisia (Tunisia); Rahmani, M., E-mail: rahmanimehdi79@yahoo.com [Unité de nanomatériaux et photonique, Université El Manar, Faculté des Sciences de Tunis, Département de Physique, 2092 El Manar, Tunis Tunisia (Tunisia); Zaïbi, M.-A [Unité de nanomatériaux et photonique, Université El Manar, Faculté des Sciences de Tunis, Département de Physique, 2092 El Manar, Tunis Tunisia (Tunisia); Ecole Nationale Supérieure des Ingénieurs de Tunis, Université de Tunis, 5 Avenue Taha Hussein, 1008 Tunis (Tunisia); Oueslati, M. [Unité de nanomatériaux et photonique, Université El Manar, Faculté des Sciences de Tunis, Département de Physique, 2092 El Manar, Tunis Tunisia (Tunisia)

2015-01-15

Nickel-porous silicon nanocomposites (PS/Ni) are elaborated by an electroless deposition method using NiCl{sub 2} aqueous solution. The presence of nickel ions in the porous layer is confirmed by Fourier Transformed InfraRed spectroscopy (FTIR) and Raman spectroscopy. The photoluminescence (PL) spectra of PS/Ni, prepared at different electroless durations (t{sub edp}), are analyzed. A remarkable enhancement in the integrated PL intensity of PS containing nickel was observed. The lower t{sub edp} favor the deposition of nickel in PS, hence the silicon dangling bonds at the porous surface are quenched and this was increased the PL intensity. However, for the longer t{sub edp}, the PL intensity has been considerably decreased due to the destruction of some Si nanocrystallites. The PL spectra of PS/Ni, for t{sub edp} less than 8 min, show a multiband profile indicating the creation of new luminescent centers by Ni elements which induces a strong modification in the emission mechanisms. - Highlights: • Deposition of Ni ions into porous silicon (PS) layer using the electroless method. • Formation of Ni–O bonds on the porous layer. • The photoluminescence (PL) intensity of PS is enhanced after Ni deposition. • The increase of the PL is due to the contribution of radiative centers related to Ni.

Nanoscale investigation of the interface situation of plated nickel and thermally formed nickel silicide for silicon solar cell metallization

Science.gov (United States)

Mondon, A.; Wang, D.; Zuschlag, A.; Bartsch, J.; Glatthaar, M.; Glunz, S. W.

2014-12-01

In the context of nickel silicide formation from plated nickel layers for solar cell metallization, there are several open questions regarding contact adhesion and electrical properties. Nanoscale characterization by transmission electron microscopy has been employed to support these investigations. Interfacial oxides and silicide phases were investigated on differently prepared samples by different analytical methods associated with transmission electron microscopy analysis. Processing variations included the pre-treatment of samples before nickel plating, the used plating solution and the thermal budget for the nickel-silicon solid-state reaction. It was shown that interface oxides of only few nm thickness on both silicon and nickel silicide are present on the samples, depending on the chosen process sequence, which have been shown to play an important role in adhesion of nickel on silicide in an earlier publication. From sample pretreatment variations, conclusions about the role of an interfacial oxide in silicide formation and its influence on phase formation were drawn. Such an oxide layer hinders silicide formation except for pinhole sites. This reduces the availability of Ni and causes a silicide with low Ni content to form. Without an interfacial oxide a continuous nickel silicide of greater depth, polycrystalline modification and expected phase according to thermal budget is formed. Information about the nature of silicide growth on typical solar cell surfaces could be obtained from silicide phase and geometric observations, which were supported by FIB tomography. The theory of isotropic NiSi growth and orientation dependent NiSi2 growth was derived. By this, a very well performing low-cost metallization for silicon solar cells has been brought an important step closer to industrial introduction.

Inhalation carcinogenicity study with nickel metal powder in Wistar rats

International Nuclear Information System (INIS)

Oller, Adriana R.; Kirkpatrick, Daniel T.; Radovsky, Ann; Bates, Hudson K.

2008-01-01

Epidemiological studies of nickel refinery workers have demonstrated an association between increased respiratory cancer risk and exposure to certain nickel compounds (later confirmed in animal studies). However, the lack of an association found in epidemiological analyses for nickel metal remained unconfirmed for lack of robust animal inhalation studies. In the present study, Wistar rats were exposed by whole-body inhalation to 0, 0.1, 0.4, and 1.0 mg Ni/m 3 nickel metal powder (MMAD = 1.8 μm, GSD = 2.4 μm) for 6 h/day, 5 days/week for up to 24 months. A subsequent six-month period without exposures preceded the final euthanasia. High mortality among rats exposed to 1.0 mg Ni/m 3 nickel metal resulted in the earlier termination of exposures in this group. The exposure level of 0.4 mg Ni/m 3 was established as the MTD for the study. Lung alterations associated with nickel metal exposure included alveolar proteinosis, alveolar histiocytosis, chronic inflammation, and bronchiolar-alveolar hyperplasia. No increased incidence of neoplasm of the respiratory tract was observed. Adrenal gland pheochromocytomas (benign and malignant) in males and combined cortical adenomas/carcinomas in females were induced in a dose-dependent manner by the nickel metal exposure. The incidence of pheochromocytomas was statistically increased in the 0.4 mg Ni/m 3 male group. Pheochromocytomas appear to be secondary to the lung toxicity associated with the exposure rather than being related to a direct nickel effect on the adrenal glands. The incidence of cortical tumors among 0.4 mg Ni/m 3 females, although statistically higher compared to the concurrent controls, falls within the historical control range; therefore, in the present study, this tumor is of uncertain relationship to nickel metal exposure. The lack of respiratory tumors in the present animal study is consistent with the findings of the epidemiological studies

Influence of Ni content on physico-chemical characteristics of Ni, Mg, Al-Hydrotalcite like compounds

Directory of Open Access Journals (Sweden)

Alexandre Carlos Camacho Rodrigues

2003-12-01

Full Text Available The physico-chemical properties of a series of Ni,Mg,Al-HTLC with Al/(Al+Mg+Ni = 0.25 and low Ni/Mg ratios were studied by means of X-ray diffraction (XRD, thermogravimetric (TGA and thermodifferential (DTA analysis, N2 physissorption and temperature programmed reduction (TPR. The as-synthesized materials were well-crystallized, with XRD patterns typical of the HTLCs in carbonate form. Upon calcination and dehydration the dehydroxilation of the layers with concurrent decomposition of carbonate anions produced mixed oxides with high surface area. XRD analysis indicated that the different nickel and aluminum oxides species are well-dispersed in a poor-crystallized MgO periclase-type phase. As observed by TPR, the different Ni species showed distinct interactions with Mg(AlO phase, which were influenced by both nickel content and calcination temperature. Regardless of the the nickel content, the reduction of nickel species was not complete as indicated by the presence of metallic dispersions.

Magnetic nanofilms of nickel prepared at the liquid-liquid interface

International Nuclear Information System (INIS)

Varghese, Neenu; Rao, C.N.R.

2011-01-01

Highlights: → Formation of nickel thinfims at the organic-aqueous interface at room temperature. → Thickness of nanofilm is ∼20 nm. → Ni nanofilms exhibit superparamagnetic behavior. → Thicker Ni films are obtained at a higher temperature (60 o C). -- Abstract: Thin films of metallic nickel with a thickness of the order of 20 nm have been prepared at the organic-aqueous interface at room temperature by the reaction of nickel cupferronate [Ni(C 6 H 5 N 2 O 2 ) 2 ] in toluene medium and sodium borohydride (NaBH 4 ) in aqueous medium. The films were characterized with transmission electron microscopy, scanning electron microscopy and atomic force microscopy. Thicker Ni films could be prepared by carrying out the reaction at the interface at 60 o C. The Ni nanofilms exhibit superparamagnetic behavior.

Moessbauer effect measurements on the intermetallic compounds Ni3Al and Ni3Ge

International Nuclear Information System (INIS)

Drijver, J.W.; Woude, F. van der

1975-01-01

Moessbauer parameters obtained from room temperature emission and absorption spectra of Ni 3 Al and Ni 3 Ga processed by a computer assuming a singlet and a doublet are given. The doublet is due to iron or cobalt atoms at the nickel site. Quadrupole splitting at 57 Fe nuclei in Ni 3 Ga is larger than in Ni 3 Al, viz. 0.52 and 0.37 mm/sec, respectively. Isomer shift at the Al/Ga position is very close to -0.02 mm/sec found in metallic nickel. Also given are the hyperfine magnetic fields at 4.2 K. Considering the preference of 57 Co and 57 Fe atoms in the lattice, the field intensities at the nickel and aluminium sites are found to be 227 +- 1 and 238 +- 1 kOe, respectively. (Z.S.)

Synthesis, structure characterization and catalytic activity of nickel tungstate nanoparticles

Science.gov (United States)

Pourmortazavi, Seied Mahdi; Rahimi-Nasrabadi, Mehdi; Khalilian-Shalamzari, Morteza; Zahedi, Mir Mahdi; Hajimirsadeghi, Seiedeh Somayyeh; Omrani, Ismail

2012-12-01

Taguchi robust design was applied to optimize experimental parameters for controllable, simple and fast synthesis of nickel tungstate nanoparticles. NiWO4 nanoparticles were synthesized by precipitation reaction involving addition of nickel ion solution to the tungstate aqueous reagent and then formation of nickel tungstate nucleolus which are insoluble in aqueous media. Effects of various parameters such as nickel and tungstate concentrations, flow rate of reagent addition and reactor temperature on diameter of synthesized nickel tungstate nanoparticles were investigated experimentally by the aid of orthogonal array design. The results for analysis of variance (ANOVA) showed that particle size of nickel tungstate can be effectively tuned by controlling significant variables involving nickel and tungstate concentrations and flow rate; while, temperature of the reactor has a no considerable effect on the size of NiWO4 particles. The ANOVA results proposed the optimum conditions for synthesis of nickel tungstate nanoparticles via this technique. Also, under optimum condition nanoparticles of NiWO4 were prepared and their structure and chemical composition were characterized by means of EDAX, XRD, SEM, FT-IR spectroscopy, UV-vis spectroscopy, and photoluminescence. Finally, catalytic activity of the nanoparticles in a cycloaddition reaction was examined.

Nanoscale investigation of the interface situation of plated nickel and thermally formed nickel silicide for silicon solar cell metallization

Energy Technology Data Exchange (ETDEWEB)

Mondon, A., E-mail: andrew.mondon@ise.fraunhofer.de [Fraunhofer ISE, Heidenhofst. 2, D-79110 Freiburg (Germany); Wang, D. [Karlsruhe Nano Micro Facility (KNMF), H.-von-Helmholz-Platz 1, D-76344 Eggenstein-Leopoldshafen (Germany); Zuschlag, A. [Universität Konstanz FB Physik, Jacob-Burckhardt-Str. 27, D-78464 Konstanz (Germany); Bartsch, J.; Glatthaar, M.; Glunz, S.W. [Fraunhofer ISE, Heidenhofst. 2, D-79110 Freiburg (Germany)

2014-12-30

Highlights: • Adhesion of metallization of fully plated nickel–copper contacts on silicon solar cells can be achieved by formation of nickel silicide at the cost of degraded cell performance. • Understanding of silicide growth mechanisms and controlled growth may lead to high performance together with excellent adhesion. • Silicide formation is well known from CMOS production from PVD-Ni on flat surfaces. Yet the deposition methods and therefore layer characteristics and the surface topography are different for plated metallization. • TEM analysis is performed for differently processed samples. • A nickel silicide growth model is created for plated Ni on textured silicon solar cells. - Abstract: In the context of nickel silicide formation from plated nickel layers for solar cell metallization, there are several open questions regarding contact adhesion and electrical properties. Nanoscale characterization by transmission electron microscopy has been employed to support these investigations. Interfacial oxides and silicide phases were investigated on differently prepared samples by different analytical methods associated with transmission electron microscopy analysis. Processing variations included the pre-treatment of samples before nickel plating, the used plating solution and the thermal budget for the nickel–silicon solid-state reaction. It was shown that interface oxides of only few nm thickness on both silicon and nickel silicide are present on the samples, depending on the chosen process sequence, which have been shown to play an important role in adhesion of nickel on silicide in an earlier publication. From sample pretreatment variations, conclusions about the role of an interfacial oxide in silicide formation and its influence on phase formation were drawn. Such an oxide layer hinders silicide formation except for pinhole sites. This reduces the availability of Ni and causes a silicide with low Ni content to form. Without an interfacial oxide

Changes of surface structure of Ni, W and chromium-nickel steel Cr18Ni10 irradiated by high fluences of krypton ions with high energies

International Nuclear Information System (INIS)

Didyk, A.Yu.; Semina, V.K.; Khalil, A.; Suvorov, A.L.; Stepanov, A.Eh.; Cheblukov, Yu.N.

1999-01-01

The surfaces of W single crystal, Ni polycrystal and chromium-nickel steel, irradiated by Kr ions with energy 305 and 245 MeV up to the fluences 2*10 15 and 3*10 15 ion/cm 2 , were studied by means of scanning electron microscopy. The evaporation coefficients of material surfaces were estimated on the base of changes of surface relief. The values of these coefficients turned out much more than ones predicted by the inelastic sputtering model. The method of 'step' was offered and realized for the more correct estimations evaporation coefficient on the Ni example. The phenomenological model explaining the observed phenomena is introduced

Recent progress in nickel carcinogenesis

Energy Technology Data Exchange (ETDEWEB)

Sunderman, F.W. Jr.

1984-01-01

Positive bacterial mutagenesis tests have been obtained with Ni(II) in Corynybacterium, but not in E. coli, S. typhimurium, or B. subtilis. Transformation assays of several soluble and crystalline Ni compounds have been positive in Syrian hamster embryo cells. Ni(II) binds to DNA, RNA, and nucleoproteins, and becomes localized in nucleoli. Genotoxic effects of Ni include: (a) chromosomal aberrations, including sister-chromatid exchanges, (b) DNA strandbreaks and DNA-protein crosslinks, (c) inhibition of DNA and RNA synthesis, (d) infidelity of DNA transcription, and (e) mutations at the HGPRTase locus in Chinese hamster cells and the TK locus in mouse lymphoma cells. These findings are consistent with somatic mutation as the mechanism for initiation of nickel carcinogenesis. Ni compounds cause reversible transition of double-stranded poly(dG-dC) DNA from the right-handed B-helix to the left-handed Z-helix, suggesting a mechanism whereby nickel might modulate oncogene expression. 99 references, 4 tables.

Size-controlled synthesis of nickel nanoparticles

International Nuclear Information System (INIS)

Hou, Y.; Kondoh, H.; Ohta, T.; Gao, S.

2005-01-01

A facile reduction approach with nickel acetylacetonate, Ni(acac) 2 , and sodium borohydride or superhydride leads to monodisperse nickel nanoparticles in the presence of hexadecylamine (HDA) and trioctylphosphine oxide (TOPO). The combination of HDA and TOPO used in the conventional synthesis of semiconductor nanocrystals also provides better control over particle growth in the metal nanoparticle synthesis. The size of Ni nanoparticles can be readily tuned from 3 to 11 nm, depending on the ratio of HDA to TOPO in the reaction system. As-synthesized Ni nanoparticles have a cubic structure as characterized by power X-ray diffraction (XRD), selected-area electron diffraction (SAED). Transmission electron microscopy (TEM) images show that Ni nanoparticles have narrow size distribution. SQUID magnetometry was also used in the characterization of Ni nanoparticles. The synthetic procedure can be extended to the preparation of high quality metal or alloy nanoparticles

Crystal structure stability and electronic properties of the layered nickelate La4Ni3O10

Science.gov (United States)

Puggioni, Danilo; Rondinelli, James M.

2018-03-01

We investigate the crystal structure and the electronic properties of the trilayer nickelate La4Ni3O10 by means of quantum-mechanical calculations in the framework of the density-functional theory. We find that, at low temperature, La4Ni3O10 undergoes a hitherto unreported structural phase transition and transforms to a new monoclinic P 21/a phase. This phase exhibits electronic properties in agreement with recent angle-resolved photoemission spectroscopy data reported in H. Li et al., [Nat. Commun. 8, 704 (2017), 10.1038/s41467-017-00777-0] and should be considered in models focused on explaining the observed ˜140 K metal-to-metal phase transition.

Structural Investigation of Fe-Ni-S and Fe-Ni-Si Melts by High-temperature Fluorescence XAFS Measurements

International Nuclear Information System (INIS)

Manghnani, Murli H.; Balogh, John; Hong Xinguo; Newville, Matthew; Amulele, G.

2007-01-01

Iron-nickel (Fe-Ni) alloy is regarded as the most abundant constituent of Earth's core, with an amount of 5.5 wt% Ni in the core based on geochemical and cosmochemical models. The structural role of nickel in liquid Fe-Ni alloys with light elements such as S or Si is poorly understood, largely because of the experimental difficulties of high-temperature melts. Recently, we have succeeded in acquiring Ni K-edge fluorescence x-ray absorption fine structure (XAFS) spectra of Fe-Ni-S and Fe-Ni-Si melts and alloys. Different structural environment of Ni atoms in Fe-Ni-S and Fe-Ni-Si melts is observed, supporting the effect of light elements in Fe-Ni melts

Adsorption of nickel on synthetic hydroxyapatite from aqueous solutions

International Nuclear Information System (INIS)

Rosskopfova, O.; Galambos, M.; Pivarciova, L.; Rajec, P.; Caplovicova, M.

2013-01-01

The sorption of nickel on synthetic hydroxyapatite was investigated using a batch method and radiotracer technique. The hydroxyapatite samples used in experiments were a commercial hydroxyapatite and hydroxyapatite of high crystallinity with Ca/P ratio of 1.563 and 1.688, respectively, prepared by a wet precipitation process. The sorption of nickel on hydroxyapatite was pH independent ranging from 4.5 to 6.5 as a result of buffering properties of hydroxyapatite. The adsorption of nickel was rapid and the percentage of Ni sorption on both samples of hydroxyapatite was >98 % during the first 15-30 min of the contact time for initial Ni 2+ concentration of 1 x 10 -4 mol dm -3 . The experimental data for sorption of nickel have been interpreted in the term of Langmuir isotherm and the value of maximum sorption capacity of nickel on a commercial hydroxyapatite and hydroxyapatite prepared by wet precipitation process was calculated to be 0.184 and 0.247 mmol g -1 , respectively. The sorption of Ni 2+ ions was performed by ion-exchange with Ca 2+ cations on the crystal surface of hydroxyapatite under experimental conditions. The competition effect of Co 2+ and Fe 2+ towards Ni 2+ sorption was stronger than that of Ca 2+ ions. NH 4 + ions have no apparent effect on nickel sorption. (author)

Toxic effect of nickel (Ni) on growth and metabolism in germinating seeds of sunflower (Helianthus annuus L.).

Science.gov (United States)

Ashraf, Muhammad Yasin; Sadiq, Rumana; Hussain, Mumtaz; Ashraf, Muhammad; Ahmad, M Sajid Aqeel

2011-12-01

To assess the toxic effect of nickel (Ni) on the growth and some key metabolic processes in sunflower, varying levels of Ni as Ni(NO(3))(2) up to 60 mg L(-1) were applied once to sunflower cultivars SF-187 and Hysun-33 at sowing time in sand culture. An increase in Ni in the growth medium adversely affected growth parameters, sugar concentration (both reducing and non-reducing), as well as the activities of α-amylase and protease. It also slowed down mobilization of stored proteins and amino acids in the germinating seeds. However, an increase in the activities of α-amylase and protease was observed over time from 24 to 120 h after sowing. Cultivar Hysun-33 showed better performance than SF-187 in the presence of excess Ni. Overall, Ni-induced reduction in germination of sunflower seed appeared to be due to disturbance in biochemical metabolism as the availability of sugars for the synthesis of metabolic energy as well as necessary amino acids for the synthesis of proteins and enzymes essential for the growing embryo are generally reduced due to suppression in α-amylase and protease activities.

Design and fabrication of highly open nickel cobalt sulfide nanosheets on Ni foam for asymmetric supercapacitors with high energy density and long cycle-life

Science.gov (United States)

Zha, Daosong; Fu, Yongsheng; Zhang, Lili; Zhu, Junwu; Wang, Xin

2018-02-01

Nickel cobalt sulfides (NiCo-S) are promising electrode materials for high-performance supercapacitors but normally show poor rate capability and unsatisfactory long-term endurance. To overcome these disadvantages, a properly constructed electrode architecture with abundant electron transport channels, excellent electronic conductivity and robust structural stability is required. Herein, considering that in situ transformation can mostly retain the specific structural advantages of the precursors, a two-step strategy is purposefully developed to construct a binder-free electrode composed of interconnected NiCo-S nanosheets on Ni foam (NiCo-S/NF), in which NiCo-S/NF is synthesized via the in situ sulfuration of networked acetate anion-intercalated nickel cobalt layered double hydroxide nanosheets loaded on Ni foam (A-NiCo-LDH/NF). Noticeably, the optimized Ni1Co1-S/NF exhibits an ultrahigh specific capacitance of 2553.9 F g-1 at 0.5 A g-1, excellent rate capability (1898.1 F g-1 at 50 A g-1) and superior cycling stability (nearly 90% capacitance retention after 10,000 cycles). Furthermore, the assembled asymmetric supercapacitor based on Ni1Co1-S/NF demonstrates a high energy density of 58.1 Wh kg-1 at a power density of 796 W kg-1 and impressive long-term durability even after a repeated charge/discharge process as long as 70,000 cycles (∼92% capacitance retention). The attractive properties endow the Ni1Co1-S/NF electrode with significant potential for high-performance energy storage devices.

Template-free approach to synthesize hierarchical porous nickel cobalt oxides for supercapacitors

Science.gov (United States)

Chang, Jie; Sun, Jing; Xu, Chaohe; Xu, Huan; Gao, Lian

2012-10-01

Nickel cobalt oxides with various Ni/Co ratios were synthesized using a facile template-free approach for electrochemical supercapacitors. The texture and morphology of the nanocomposites were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Brunauer-Emmett-Teller analysis (BET). The results show that a hierarchical porous structure assembled from nanoflakes with a thickness of ~10 nm was obtained, and the ratio of nickel to cobalt in the nanocomposites was very close to the precursors. Cyclic voltammetry (CV) and galvanostatic charge and discharge tests were carried out to study the electrochemical performance. Both nickel cobalt oxides (Ni-Co-O-1 with Ni : Co = 1, Ni-Co-O-2 with Ni : Co = 2) outperform pure NiO and Co3O4. The Ni-Co-O-1 and Ni-Co-O-2 possess high specific capacities of 778.2 and 867.3 F g-1 at 1 A g-1 and capacitance retentions of 84.1% and 92.3% at 10 A g-1, respectively. After full activation, the Ni-Co-O-1 and Ni-Co-O-2 could achieve a maximum value of 971 and 1550 F g-1 and remain at ~907 and ~1450 F g-1 at 4 A g-1, respectively. Also, the nickel cobalt oxides show high capacity retention when fast charging.Nickel cobalt oxides with various Ni/Co ratios were synthesized using a facile template-free approach for electrochemical supercapacitors. The texture and morphology of the nanocomposites were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Brunauer-Emmett-Teller analysis (BET). The results show that a hierarchical porous structure assembled from nanoflakes with a thickness of ~10 nm was obtained, and the ratio of nickel to cobalt in the nanocomposites was very close to the precursors. Cyclic voltammetry (CV) and galvanostatic charge and discharge tests were carried out to study the electrochemical performance. Both nickel cobalt oxides (Ni-Co-O-1 with Ni : Co = 1, Ni-Co-O-2 with Ni

Nickel hydroxide modified electrodes for urea determination

Directory of Open Access Journals (Sweden)

Luiz Henrique Dall´Antonia

2007-03-01

Full Text Available Nickel hydroxide films were prepared by electrodeposition from a solution Ni(NO32 0,05 mol L ?¹ on ITO electrodes (Tin oxide doped with Indium on PET-like plastic film, applying a current of - 0,1 A cm ?² during different time intervals between 1800 and 7200 s. The electrochemical behavior of the nickel hydroxide electrode was investigated through a cyclic voltammogram, in NaOH 1,0 mol L ?¹, where it was observed two peaks in the profile in 0,410 and 0,280 V, corresponding to redox couple Ni(II/Ni(III. A sensor for urea presenting a satisfactory answer can be obtained when, after the deposit of the film of Ni(OH2 on the electrode of nickel, it is immersed in a solution of NaOH 1,0 mol L ?¹ and applying a potential of + 0,435 V, where the maximum of the anodic current occurs in the cyclic voltammogram. Analyzing the results it can be observed that, for a range of analite concentration between 5 to 50 m mol L ?¹, the behavior is linear and the sensibility found was of 20,3 mA cm?² (mol L?¹?¹, presenting reproducibility confirming the nickel hydroxide electrodes utilization for the determination of urea.

Development of a Micro-Fiber Nickel Electrode for Nickel-Hydrogen Cell

Science.gov (United States)

Britton, Doris L.

1996-01-01

The development of a high specific energy battery is one of the objectives of the lightweight nickel-hydrogen (NiH2) program at the NASA Lewis Research Center. The approach has been to improve the nickel electrode by continuing combined in-house and contract efforts to develop a more efficient and lighter weight electrode for the nickel-hydrogen fuel cell. Small fiber diameter nickel plaques are used as conductive supports for the nickel hydroxide active material. These plaques are commercial products and have an advantage of increased surface area available for the deposition of active materials. Initial tests include activation and capacity measurements at different discharge levels followed by half-cell cycle testing at 80 percent depth-of-discharge in a low Earth orbit regime. The electrodes that pass the initial tests are life cycle tested in a boiler plate nickel-hydrogen cell before flightweight designs are built and tested.

Synthesis and Electrocatalytic Activity of Ammonium Nickel Phosphate, [NH4]NiPO4·6H2O, and β-Nickel Pyrophosphate, β-Ni2P2O7: Catalysts for Electrocatalytic Decomposition of Urea.

Science.gov (United States)

Meguerdichian, Andrew G; Jafari, Tahereh; Shakil, Md R; Miao, Ran; Achola, Laura A; Macharia, John; Shirazi-Amin, Alireza; Suib, Steven L

2018-02-19

Electrocatalytic decomposition of urea for the production of hydrogen, H 2, for clean energy applications, such as in fuel cells, has several potential advantages such as reducing carbon emissions in the energy sector and environmental applications to remove urea from animal and human waste facilities. The study and development of new catalyst materials containing nickel metal, the active site for urea decomposition, is a critical aspect of research in inorganic and materials chemistry. We report the synthesis and application of [NH 4 ]NiPO 4 ·6H 2 O and β-Ni 2 P 2 O 7 using in situ prepared [NH 4 ] 2 HPO 4 . The [NH 4 ]NiPO 4 ·6H 2 O is calcined at varying temperatures and tested for electrocatalytic decomposition of urea. Our results indicate that [NH 4 ]NiPO 4 ·6H 2 O calcined at 300 °C with an amorphous crystal structure and, for the first time applied for urea electrocatalytic decomposition, had the greatest reported electroactive surface area (ESA) of 142 cm 2 /mg and an onset potential of 0.33 V (SCE) and was stable over a 24-h test period.

External self-gettering of nickel in float zone silicon wafers

Science.gov (United States)

Gay, N.; Martinuzzi, S.

1997-05-01

During indiffusion of Ni atoms in silicon crystals at 950 °C from a nickel layer source, Ni-Si alloys can be formed close to the surface. Metal solubility in these alloys is higher than in silicon, which induces a marked segregation gettering of the Ni atoms which have diffused in the bulk of the wafers. Consequently, the regions of the wafers covered with the Ni layer are less contaminated than adjacent regions in which Ni atoms have also penetrated, as shown by the absence of precipitates and the higher diffusion length of minority carriers. The results suggest the existence of external self-gettering of Ni atoms by the nickel source.

Csbnd H⋯Ni and Csbnd H⋯π(chelate) interactions in nickel(II) complexes involving functionalized dithiocarbamates and triphenylphosphine

Science.gov (United States)

Sathiyaraj, E.; Thirumaran, S.; Selvanayagam, S.; Sridhar, B.; Ciattini, Samuele

2018-05-01

New bis(N-benzyl-N-substituted benzyldithiocarbamato-S,S‧)nickel(II) (1-3) and (N-benzyl-N-substituted benzyldithiocarbamato-S,S‧)(isothiocyanato-N)- (triphenylphosphane)nickel(II) (4-6) [where substituted benzyl = 2-HOsbnd C6H4sbnd CH2sbnd (1,4), 3-HOsbnd C6H4sbnd CH2sbnd (2,5), 4-Fsbnd C6H4sbnd CH2sbnd (3,6)] were synthesized and characterized using IR, electronic, and NMR (1H and 13C) spectra. X-ray structural analysis of homoleptic complex (1) and heteroleptic complexes (5 and 6) confirmed the presence of four coordinated nickel in a distorted square planar arrangement with NiS4 and NiS2PN chromophores, respectively. The νC-S stretching vibrations are observed around 990 cm-1 without any splitting supporting the bidentate coordination of the dithiocarbamate ligand. Electronic spectral studies of all the complexes (1-6) indicate that the geometry of the nickel atom is probably square planar. NMR spectra of all homoleptic and heteroleptic complexes (1-6) reveal a weak signal associated with the backbone carbon (N13CS2) in the region 204.0-210.0 ppm with a weak intensity characteristic of the quaternary carbon signals. The greater trans influence of triphenylphosphine in complexes 5 and 6 is supported by the long Nisbnd S distance compared to other Nisbnd S distance which is opposite to the NCS- ligand. In the structure of complex 5, C-H⋯π(chelate) interactions results in polymeric chain. Both structures show intramolecular Ni⋯H interactions but that on 6 is the strongest. C-H⋯π interactions are also found in 1, 5 and 6. Hirshfeld surface analysis and the associated 2D fingerprint plots of 1, 5 and 6 have been studied to evaluate intermolecular interactions. The molecular geometries of complexes 1, 5 and 6 have been optimized by abinitio HF method using LANL2DZ program.

Formation of nickel-tantalum compounds in tantalum fluoride halide melts

International Nuclear Information System (INIS)

Matychenko, Eh.S.; Zalkind, O.A.; Kuznetsov, B.Ya.; Orlov, V.M.; Sukhorzhevskaya, S.L.

2001-01-01

Interaction of nickel with NaCl-K 2 TaF 7 melt (14 mol.%) at 750 deg C was studied, the composition of intermetallic compounds formed in Ni-Ta system being analyzed, using the methods of chemical and X-ray phase analyses, IR spectroscopy. It was ascertained that composition of intermetallic compounds (Ni 3 Ta, Ni 2 Ta) depends on K 2 TaF 7 concentration in the melt, metallic tantalum additions, nickel substrate thickness and experiment duration. The mechanism of currentless deposition of tantalum on nickel was considered and the assumption was made that disproportionation reaction lies in the basis of the process [ru

Modeling and simulation of NiO dissolution and Ni deposition in molten carbonate fuel cells

Energy Technology Data Exchange (ETDEWEB)

Nam, Suk Woo; Choi, Hyung-Joon; Lim, Tae Hoon [Korea Institute of Science & Technology, Seoul (Korea, Republic of)] [and others

1996-12-31

Dissolution of NiO cathode into the electrolyte matrix is an important phenomena limiting the lifetime of molten carbonate fuel cell (MCFC). The dissolved nickel diffuses into the matrix and is reduced by dissolved hydrogen leading to the formation of metallic nickel films in the pores of the matrix. The growth of Ni films in the electrolyte matrix during the continuous cell operation results eventually in shorting between cathode and anode. Various mathematical and empirical models have been developed to describe the NiO dissolution and Ni deposition processes, and these models have some success in estimating the lifetime of MCFC by correlating the amount of Ni deposited in the matrix with shorting time. Since the exact mechanism of Ni deposition was not well understood, deposition reaction was assumed to be very fast in most of the models and the Ni deposition region was limited around a point in the matrix. In fact, formation of Ni films takes place in a rather broad region in the matrix, the location and thickness of the film depending on operating conditions as well as matrix properties. In this study, we assumed simple reaction kinetics for Ni deposition and developed a mathematical model to get the distribution of nickel in the matrix.

EBSD and EDS of nickel sulfide inclusions in glass

International Nuclear Information System (INIS)

Miflin, G.E.; Barry, J.C.

2002-01-01

Full text: A delayed phase transformation in small nickel sulfide inclusions can cause spontaneous fracture in toughened glass. Typically, a phase transformation within a 5 ?g nickel sulphide inclusion may break a window which weighs more than 50 kg. In most cases the nickel sulfide inclusions are detected only after window failure, although it is possible to detect the inclusions within intact glass. It is known that only type three nickel sulphide inclusions, that is, inclusions with a composition in the range Ni 7 S 6 to NiS 1.03 , break the glass. The solid-state phase transformation of alpha Ni 1-x S to beta NiS which induces a 2.5% volume increase has been given as the main reason for the spontaneous fracture. The aim of this present study is to investigate the crystal structure of phases within the type three inclusions using scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). With EBSD it is possible to map regions of alpha Ni 1-x S and to distinguish those regions from regions with beta Ni 1-x S when the elemental compositions of the two regions are identical. The inclusions of this study came from two sources. One set of inclusions were found at initiation-of-fracture in glass windows that had failed by spontaneous fracture, while the other set were found in intact windows. All of the inclusions came from windows on buildings in the Brisbane area. The EBSD analysis was done at 20kV with the stage tilted to 70 degrees on a Philips XL30 SEM with LaB 6 filament, and with attached Oxford/Link Opal camera and software. EBSD mapping was done for alpha nickel sulfide (Ni 1-x S), beta nickel sulphide (NiS), heazelwoodite (Ni 3 S 2 ), and godlevskite (Ni 9 S 8 ). The integration time was 1.3 seconds for each point. Colour coded crystal phase and grain orientation maps were produced. EDS analysis was also done on the Philips XL30 with attached EDAX EDS detector. We found that although the EBSD technique is successful in identifying alpha

Discharge capacity and microstructures of La Mg Pr Al Mn Co Ni alloys for nickel-metal hydride batteries

International Nuclear Information System (INIS)

Casini, J.C.S.; Galdino, G.S.; Ferreira, E.A.; Takiishi, H.; Faria, R.N.

2010-01-01

La 0.7-x Mg x Pr 0.3 Al 0.3 Mn 0.4 Co 0.5 Ni 3.8 (x = 0.0, 0.3 and 0.7) alloys have been investigated aiming the production of negative electrodes for nickel-metal hydride batteries. The alloys employed in this work were used in the as cast state. The results showed that the substitution of magnesium by lanthanum increased the discharge capacity of the Ni-MH batteries. A battery produced with the La 0.4 Mg 0.3 Pr 0.3 Al 0.3 Mn 0.4 Co 0.5 Ni 3.8 alloy shown a high discharge capacity (380mAh/g) also good stability compared to other alloys. The electrode materials were characterized using scanning electron microscopy (SEM) and X-ray diffraction (XRD). (author)

Structural conditions of achieving maximum ductility of two-phase Ni-NiO alloys

International Nuclear Information System (INIS)

Grabin, V.V.; Dabizha, E.V.; Movchan, B.A.

1984-01-01

A study was made on possibility of increasing ductility of two-phase Ni-NiO alloys, proJuced by traditional technology: ingot smelting, rolling and corresponding annealing for production of grain with certain size. The correlation of mechanical properties of Ni-NiO alloys and pure nickel shows that completion of the structural conJition D--lambda (where D - the average grain diameter, lambda - the value of free path between particles) in two-phase alloys enables: to increase the ultimate strength 1.5 times and preserve the basic level of pure nickel plasticity - at 20 deg C; to increase plasticity 1.4-1.5 times with preserved basic level of pure nickel plasticity - at 800 deg C. The conclusions testify to possibility of controlling mechanical properties of two-phase alloys using structural D and lambda parameters It is proposed that creation of structures with more unifor m particle distribution with respect to sizes will the accompanied by further increase of plasticity under D=lambda condition

Nickel stabilization efficiency of aluminate and ferrite spinels and their leaching behavior.

Science.gov (United States)

Shih, Kaimin; White, Tim; Leckie, James O

2006-09-01

Stabilization efficiencies of spinel-based construction ceramics incorporating simulated nickel-laden waste sludge were evaluated and the leaching behavior of products investigated. To simulate the process of immobilization, nickel oxide was mixed alternatively with gamma-alumina, kaolinite, and hematite. These tailoring precursors are commonly used to prepare construction ceramics in the building industry. After sintering from 600 to 1480 degrees C at 3 h, the nickel aluminate spinel (NiAl204) and the nickel ferrite spinel (NiFe204) crystallized with the ferrite spinel formation commencing about 200-300 degrees C lower than for the aluminate spinel. All the precursors showed high nickel incorporation efficiencies when sintered at temperatures greater than 1250 degrees C. Prolonged leach tests (up to 26 days) of product phases were carried out using a pH 2.9 acetic acid solution, and the spinel products were invariably superior to nickel oxide for immobilization over longer leaching periods. The leaching behavior of NiAl2O4 was consistent with congruent dissolution without significant reprecipitation, but for NiFe2O4, ferric hydroxide precipitation was evident. The major leaching reaction of sintered kaolinite-based products was the dissolution of cristobalite rather than NiAl2O4. This study demonstrated the feasibility of transforming nickel-laden sludge into spinel phases with the use of readily available and inexpensive ceramic raw materials, and the successful reduction of metal mobility under acidic environments.

Copper, Aluminum and Nickel: A New Monocrystalline Orthodontic Alloy

Science.gov (United States)

Wierenga, Mark

Introduction: This study was designed to evaluate, via tensile and bend testing, the mechanical properties of a newly-developed monocrystalline orthodontic archwire comprised of a blend of copper, aluminum, and nickel (CuAlNi). Methods: The sample was comprised of three shape memory alloys; CuAlNi, copper nickel titanium (CuNiTi), and nickel titanium (NiTi); from various orthodontic manufacturers in both 0.018" round and 0.019" x 0.025" rectangular dimensions. Additional data was gathered for similarly sized stainless steel and beta-titanium archwires as a point of reference for drawing conclusions about the relative properties of the archwires. Measurements of loading and unloading forces were recorded in both tension and deflection testing. Repeated-measure ANOVA (alpha= 0.05) was used to compare loading and unloading forces across wires and one-way ANOVA (alpha= 0.05) was used to compare elastic moduli and hysteresis. To identify significant differences, Tukey post-hoc comparisons were performed. Results: The modulus of elasticity, deflection forces, and hysteresis profiles of CuAlNi were significantly different than the other superelastic wires tested. In all tests, CuAlNi had a statistically significant lower modulus of elasticity compared to the CuNiTi and NiTi wires (P orthodontic metallurgy.

Assaying environmental nickel toxicity using model nematodes

Science.gov (United States)

Rudel, David; Douglas, Chandler; Huffnagle, Ian; Besser, John M.; Ingersoll, Christopher G.

2013-01-01

Although nickel exposure results in allergic reactions, respiratory conditions, and cancer in humans and rodents, the ramifications of excess nickel in the environment for animal and human health remain largely undescribed. Nickel and other cationic metals travel through waterways and bind to soils and sediments. To evaluate the potential toxic effects of nickel at environmental contaminant levels (8.9-7,600 µg Ni/g dry weight of sediment and 50-800 µg NiCl2/L of water), we conducted assays using two cosmopolitan nematodes, Caenorhabditis elegans and Pristionchus pacificus. We assayed the effects of both sediment-bound and aqueous nickel upon animal growth, developmental survival, lifespan, and fecundity. Uncontaminated sediments were collected from sites in the Midwestern United States and spiked with a range of nickel concentrations. We found that nickel-spiked sediment substantially impairs both survival from larval to adult stages and adult longevity in a concentration-dependent manner. Further, while aqueous nickel showed no adverse effects on either survivorship or longevity, we observed a significant decrease in fecundity, indicating that aqueous nickel could have a negative impact on nematode physiology. Intriguingly, C. elegansand P. pacificus exhibit similar, but not identical, responses to nickel exposure. Moreover, P. pacificus could be tested successfully in sediments inhospitable to C. elegans. Our results add to a growing body of literature documenting the impact of nickel on animal physiology, and suggest that environmental toxicological studies could gain an advantage by widening their repertoire of nematode species.

Absorption and retention of nickel from drinking water in relation to food intake and nickel sensitivity.

Science.gov (United States)

Nielsen, G D; Søderberg, U; Jørgensen, P J; Templeton, D M; Rasmussen, S N; Andersen, K E; Grandjean, P

1999-01-01

Two studies were performed to examine the influence of fasting and food intake on the absorption and retention of nickel added to drinking water and to determine if nickel sensitization played any role in this regard. First, eight nonallergic male volunteers fasted overnight before being given nickel in drinking water (12 micrograms Ni/kg) and, at different time intervals, standardized 1400-kJ portions of scrambled eggs. When nickel was ingested in water 30 min or 1 h prior to the meal, peak nickel concentrations in serum occurred 1 h after the water intake, and the peak was 13-fold higher than the one seen 1 h after simultaneous intake of nickel-containing water and scrambled eggs. In the latter case, a smaller, delayed peak occurred 3 h after the meal. Median urinary nickel excretion half-times varied between 19.9 and 26.7 h. Within 3 days, the amount of nickel excreted corresponded to 2.5% of the nickel ingested when it was mixed into the scrambled eggs. Increasing amounts were excreted as the interval between the water and the meal increased, with 25.8% of the administered dose being excreted when the eggs were served 4 h prior to the nickel-containing drinking water. In the second experiment, a stable nickel isotope, 61Ni, was given in drinking water to 20 nickel-sensitized women and 20 age-matched controls, both groups having vesicular hand eczema of the pompholyx type. Nine of 20 nickel allergic eczema patients experienced aggravation of hand eczema after nickel administration, and three also developed a maculopapular exanthema. No exacerbation was seen in the control group. The course of nickel absorption and excretion in the allergic groups did not differ and was similar to the pattern seen in the first study, although the absorption in the women was less. A sex-related difference in gastric emptying rates may play a role. Thus, food intake and gastric emptying are of substantial significance for the bioavailability of nickel from aqueous solutions

Recent progress in nickel carcinogenesis. [Cornybacterium; E. coli; S. typhimurium; B. subtillis

Energy Technology Data Exchange (ETDEWEB)

Sunderman, F.W. Jr.

1984-01-01

Research on nickel carcinogenesis from 1979 to 1983 is reviewed. Epidemiological studies have strengthened the evidence that workers in nickel refineries have increased risks of lung and sinonasal cancers, but have not substantiated increased risks of respiratory cancers in other nickel-exposed workers. Carcinogenesis bioassays have demonstrated carcinogenicity of certain nickel sulfide, hydroxide, selenide, arsenide, antimonide, and telluride compounds following parenteral administration to rodents. Positive bacterial mutagenesis tests have been obtained with Ni(II) in Cornybacterium, but not in E. coli, S. typhimurium, or B. subtilis. Transformation assays of several soluble and crystalline Ni compounds have been positive in Syrian hamster embryo cells. Ni(II) binds to DNA, RNA, and nucleoproteins, and becomes localized in nucleoli. Genotoxic effects of Ni include: (a) chromosomal aberrations, including sister-chromatid exchanges, (b) DNA strandbreaks and DNA-protein cross-links, (c) inhibition of DNA and RNA synthesis, (d) infidelity of DNA transcription, and (e) mutations at the HGPRTase locus in Chinese hamster cells and the TK locus in mouse lymphoma cells. These findings are consistent with somatic mutation as the mechanism for initiation of nickel carcinogenesis. Ni compounds cause reversible transition of double-stranded poly(dG-dC) DNA from the right-handed B-helix to the left-handed Z-helix, suggesting a mechanism whereby nickel might modulate oncogene expression. 99 references, 6 tables.

Electroplating Ni-63 metal ions in chloride bath on the Cu-plate

Energy Technology Data Exchange (ETDEWEB)

Yoo, Kwon Mo; Uhm, Young Rang; Son, Kwang Jae; Park, Keun Yung [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2014-05-15

Ni-63 plating is similar to other electroplating processes that employ soluble metal anodes. The nickel plating solution described by Watts in 1916 eventually replaced all other strategies in use up to that time. Charged Ni ions are formed by sulfate, sulfamate, chloride, and a Watts bath. However, charged Ni-63 ions are formed by dissolving metal Ni-63. Specifically, it requires the passage of direct current (DC) between two electrodes that are immersed in a conductive, aqueous solution of nickel salts. The flow of a DC causes one of the electrodes (the anode) to dissolve and the other electrode (the cathode) to become covered with nickel. The nickel in the solution is present in the form of divalent positively charged ions (Ni{sup 2+}). When the current flows, the positive ions react with two electrons (2e{sup -}) and are converted into metallic nickel (Ni{sup 0}) at the cathode surface. In the present study, we optimize and established process for the electroplating Ni-63 on Cu-plate. Nanocrystalline nickel (Ni) coatings were synthesized by DC electro deposition at a current density of 15 mA/cm{sup 2}. The bath was primarily composed of 0.2 M Ni ions, prepared by dissolving Ni-63 metal particles in HCl. The prototype for electroplating radioactive Ni-63 has been established. The electroplating was carried out by two-step processes such as preparation of ionic solution including Ni-63, and coating processes on the substrate.

Electroplating Ni-63 metal ions in chloride bath on the Cu-plate

International Nuclear Information System (INIS)

Yoo, Kwon Mo; Uhm, Young Rang; Son, Kwang Jae; Park, Keun Yung

2014-01-01

Ni-63 plating is similar to other electroplating processes that employ soluble metal anodes. The nickel plating solution described by Watts in 1916 eventually replaced all other strategies in use up to that time. Charged Ni ions are formed by sulfate, sulfamate, chloride, and a Watts bath. However, charged Ni-63 ions are formed by dissolving metal Ni-63. Specifically, it requires the passage of direct current (DC) between two electrodes that are immersed in a conductive, aqueous solution of nickel salts. The flow of a DC causes one of the electrodes (the anode) to dissolve and the other electrode (the cathode) to become covered with nickel. The nickel in the solution is present in the form of divalent positively charged ions (Ni 2+ ). When the current flows, the positive ions react with two electrons (2e - ) and are converted into metallic nickel (Ni 0 ) at the cathode surface. In the present study, we optimize and established process for the electroplating Ni-63 on Cu-plate. Nanocrystalline nickel (Ni) coatings were synthesized by DC electro deposition at a current density of 15 mA/cm 2 . The bath was primarily composed of 0.2 M Ni ions, prepared by dissolving Ni-63 metal particles in HCl. The prototype for electroplating radioactive Ni-63 has been established. The electroplating was carried out by two-step processes such as preparation of ionic solution including Ni-63, and coating processes on the substrate

Nickel hydroxide positive electrode for alkaline rechargeable battery

Science.gov (United States)

Young, Kwo; Wang, Lixin; Mays, William; Reichman, Benjamin; Chao-Ian, Hu; Wong, Diana; Nei, Jean

2018-02-20

Certain nickel hydroxide active cathode materials for use in alkaline rechargeable batteries are capable of transferring >1.3 electrons per Ni atom under reversible electrochemical conditions. The specific capacity of the nickel hydroxide active materials is for example .gtoreq.325 mAh/g. The cathode active materials exhibit an additional discharge plateau near 0.8 V vs. a metal hydride (MH) anode. Ni in an oxidation state of less than 2, such as Ni.sup.1+, is able to participate in electrochemical reactions when using the present cathode active materials. It is possible that up to 2.3 electrons, up to 2.5 electrons or more may be transferred per Ni atom under electrochemical conditions.

Nickel hydroxide positive electrode for alkaline rechargeable battery

Science.gov (United States)

Young, Kwo; Wang, Lixin; Mays, William; Reichman, Benjamin; Chao-Ian, Hu; Wong, Diana; Nei, Jean

2018-04-03

Certain nickel hydroxide active cathode materials for use in alkaline rechargeable batteries are capable of transferring >1.3 electrons per Ni atom under reversible electrochemical conditions. The specific capacity of the nickel hydroxide active materials is for example .gtoreq.325 mAh/g. The cathode active materials exhibit an additional discharge plateau near 0.8 V vs. a metal hydride (MH) anode. Ni in an oxidation state of less than 2, such as Ni.sup.1+, is able to participate in electrochemical reactions when using the present cathode active materials. It is possible that up to 2.3 electrons, up to 2.5 electrons or more may be transferred per Ni atom under electrochemical conditions.

Synthesis, characterization and antibacterial activity of copper, nickel and bimetallic Cu–Ni nanoparticles for potential use in dental materials

Directory of Open Access Journals (Sweden)

Liliana Argueta-Figueroa

2014-08-01

Full Text Available The antibacterial effect is a desirable property in dental materials. Development of simple methods for the preparation of nanosized metal particles has attracted significant attention because of their future applications due to unusual size-dependent antibacterial properties. Copper (Cu, Nickel (Ni and bimetallic Cu–Ni nanoparticles were prepared by a simple chemical method and their antibacterial activity was tested against the widely used standard human pathogens Staphylococcus aureus (gram-negative and Escherichia coli (gram-positive. Additionally, these nanoparticles were tested against the dental pathogen Streptococcus mutans. Our results are promising for potential use in dental materials science.

Electrolytic nickel deposits upon uranium; Depot electrolytique de nickel sur l'uraniun

Energy Technology Data Exchange (ETDEWEB)

Baudin, G; Chauvin, G; Coriou, H; Hure, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1958-07-01

The authors present a new possibility to protect uranium by very adherent nickel deposits got by aqueous medium electrolysis. Surface treatment of uranium is based upon the chemical etching method from Lietazke. After thermal treatments at 600, 700 and 800 deg. C, under vacuum, a good intermetallic U-Ni diffusion is observed for each case. (author) [French] Les auteurs mettent en evidence une possibilite nouvelle de protection de l'uranium par des depots tres adherents de nickel realises par electrolyse en milieu aqueux. La preparation de surface de l'uranium est basee sur la methode du decapage chimique de Lietazke. Apres des traitements thermiques a 600, 700 et 800 deg. C, sous vide, on constate dans tous les cas une bonne diffusion intermetallique U-Ni. (auteur)

Metallic nickel nanoparticles and their effect on the embryonic development of the sea urchin Paracentrotus lividus

International Nuclear Information System (INIS)

Kanold, Julia Maxi; Wang, Jiabin; Brümmer, Franz; Šiller, Lidija

2016-01-01

The presence of nanoparticles in many industrial applications and daily products is making it nowadays crucial to assess their impact when exposed to the environment. Metallic nickel nanoparticles (Ni NPs) are of high industrial interest due to their ability to catalyze the reversible hydration of CO_2 to carbonic acid at ambient conditions. We characterized metallic Ni NPs by XRD, HRTEM and EDS and determined the solubility of free nickel ions from 3 mg/L metallic Ni NPs in seawater by ICP-MS over 96 h, which was below 3%. Further, embryonic development of the sea urchin Paracentrotus lividus was investigated for 48 h in the presence of metallic Ni NPs (0.03 mg/L to 3 mg/L), but no lethal effects were observed. However, 3 mg/L metallic Ni NPs caused a size reduction similar to 1.2 mg/L NiCl_2*6 H_2O. The obtained results contribute to current studies on metallic Ni NPs and point to their consequences for the marine ecosystem. - Highlights: • Low solubility of nickel ions from metallic nickel nanoparticles in seawater. • No lethality of sea urchin embryos up to 3 mg/L metallic nickel nanoparticles. • Considerable size reduction after 48 h was comparable to the reduction for 1.2 mg/L nickel salt. • Contributes to the overall understanding of metallic Ni NPs in the marine environment. - Metallic nickel nanoparticles display weak dissolution rates in seawater, but higher concentrations resulted in similar effects on sea urchin embryonic development as nickel salt.

X-ray diffraction and Moessbauer studies on superparamagnetic nickel ferrite (NiFe{sub 2}O{sub 4}) obtained by the proteic sol–gel method

Energy Technology Data Exchange (ETDEWEB)

Nogueira, N.A.S. [Departamento de Engenharia Metalúrgica e de Materiais, Centro de Tecnologia, Campus do Pici, Universidade Federal do Ceará – UFC, 60455-760 Fortaleza, CE (Brazil); Utuni, V.H.S.; Silva, Y.C. [Departamento de Física, Universidade Federal do Ceará – UFC, Campus do Pici, 60440-970 Fortaleza, CE (Brazil); Kiyohara, P.K. [Instituto de Física, Universidade de São Paulo – USP, 05315-970 São Paulo, SP (Brazil); Vasconcelos, I.F. [Departamento de Engenharia Metalúrgica e de Materiais, Centro de Tecnologia, Campus do Pici, Universidade Federal do Ceará – UFC, 60455-760 Fortaleza, CE (Brazil); Miranda, M.A.R., E-mail: marcus.a.r.miranda@gmail.com [Departamento de Física, Universidade Federal do Ceará – UFC, Campus do Pici, 60440-970 Fortaleza, CE (Brazil); Sasaki, J.M. [Departamento de Física, Universidade Federal do Ceará – UFC, Campus do Pici, 60440-970 Fortaleza, CE (Brazil)

2015-08-01

Nickel ferrite (NiFe{sub 2}O{sub 4}) nanoparticles were synthesized by the proteic sol–gel method at synthesis temperature of 250 °C, 300 °C and 400 °C, with the objective of obtaining superparamagnetic nanoparticles. Thermogravimetric analysis (TGA) and temperature-programed oxidation (TPO) presented peaks around 290 °C indicating that nickel ferrite was forming at this temperature. X-ray powder diffraction (XRPD) confirmed that the polycrystalline sample was single phased NiFe{sub 2}O{sub 4} with space group Fd3m. Scherrer equation applied to the diffraction patterns and transmission electron microscopy (TEM) images showed that the size of the nanoparticles ranged from 9 nm to 13 nm. TEM images also revealed that the nanoparticles were agglomerated, which was supported by the low values of surface area provided by the Brunauer-Emmet-Teller (BET) method. Moessbauer spectroscopy presented spectra composed of a superposition of three components: a sextet, a doublet and a broad singlet pattern. The sample synthetized at 300 °C had the most pronounced doublet pattern characteristic of superparamagnetic nanoparticles. In conclusion, this method was partially successful in obtaining superparamagnetic nickel ferrite nanoparticles, in which the synthetized samples were a mixture of nanoparticles with blocking temperature above and below room temperature. Magnetization curves revealed a small hysteresis, supporting the Moessbauer results. The sample with the higher concentration of superparamagnetic nanoparticles being the one synthetized at 300 °C. - Highlights: • Superparamagnetic nickel ferrite nanoparticles were grown by the proteic sol–gel method. • The proteic sol–gel method provided superparamagnetic nickel ferrite nanoparticles with sizes in the range of 9–13 nm. • Nickel ferrite nanoparticles were prepared at temperatures as low as 250 °C. • The nickel ferrite nanoparticles were studied by x-ray diffraction and Moessbauer.

Improvement of solvents for chemical decontamination: nickel ferrites removal

International Nuclear Information System (INIS)

Figueroa, Carlos A.; Morando, Pedro J.; Blesa, Miguel A.

1999-01-01

Carboxylic acids are usually included in commercial solvents for the chemical cleaning and decontamination of metal surfaces from the oxide layers grown and/or deposited from high temperature water by corrosive process. In particular oxalic acid is included in second path of AP-Citrox method. However, in some cases, their use shows low efficiency. This fact is attributed to the special passivity of the mixed oxides as nickel ferrites. This work reports a kinetic study of dissolution of a synthetic nickel ferrite (NiFe 2 O 4 ) confronted with simple oxides (NiO and Fe 2 O 3 ) in mineral acids and oxalic acid. The dissolution factor and reaction rate were determined in several conditions (reactive concentrations, pH and added ferrous ions). Experimental data of dissolution (with and without Fe(II) added) show a congruent kinetic regime. Pure nickel oxide (NiO) is rather resistant to the attack by oxalic acid solutions, and ferrous ions do not accelerate dissolution. In fact, nickel oxide dissolves better by oxidative attack that takes advantage of the higher lability of Ni 3+ . It may be concluded that oxalic acid operates to dissolve iron, and the ensuing disruption of the solid framework accelerates the release of nickel. Our results point to use more reactive solvents in iron from mixed oxides and to the possibility of using one stage decontamination method. (author)

The ternary system nickel-nobium-carbon

International Nuclear Information System (INIS)

Stadelmaier, H.H.; Fiedler, M.L.

1975-01-01

The ternary system nickel-niobium-carbon was studied by metallographic and X-ray diffraction methods to produce a liquidus projection and an isothermal section at 1,100 0 C. The liquidus projection is dominated by a wide field of primary NbC that extends far into the nickel corner of the composition triangle. Only one ternary compound is observed in this system, an eta-carbide formed in a peritectoid reaction. It has a narrow homogeneity range at Ni 2 Nb 4 C, and its lattice constant in alloys quenched from 1,100 0 C varies between 11.659 and 11.667 A. No eta-carbide Ni 3 Nb 3 C or Ni 6 Nb 6 could be detected. (orig.) [de

Influence of nickel addition on magnetic and electro-mechanical ...

Indian Academy of Sciences (India)

Unknown

The magnetic properties of Ni-rich (Ni ~ 82%) alloy at 100 Hz were found to be better than the low Ni. (Ni ~ 47%) ... used in rotor and stator laminations, stepping motors, shieldings .... the low nickel alloy had a higher saturation induction of.

Advances in nickel hydrogen technology at Yardney Battery Division

Science.gov (United States)

Bentley, J. G.; Hall, A. M.

1987-01-01

The current major activites in nickel hydrogen technology being addressed at Yardney Battery Division are outlined. Five basic topics are covered: an update on life cycle testing of ManTech 50 AH NiH2 cells in the LEO regime; an overview of the Air Force/industry briefing; nickel electrode process upgrading; 4.5 inch cell development; and bipolar NiH2 battery development.

Nickel nanoparticle decorated graphene for highly selective isolation of polyhistidine-tagged proteins

Science.gov (United States)

Liu, Jia-Wei; Yang, Ting; Ma, Lin-Yu; Chen, Xu-Wei; Wang, Jian-Hua

2013-12-01

Nickel nanoparticle decorated graphene (GP-Ni) is prepared by one-pot hydrothermal reduction of graphene oxide and nickel cations by hydrazine hydrate in the presence of poly(sodium-p-styrenesulfonate) (PSS). The GP-Ni hybrid is characterized by XRD, TEM, SEM, XPS, Raman and FT-IR spectra, demonstrating the formation of poly-dispersed nickel nanoparticles with an average size of 83 nm attached on the surface of graphene sheets. The GP-Ni hybrid exhibits ferromagnetic behavior with a magnetization saturation of 31.1 emu g-1 at 10 000 Oersted (Oe). The GP-Ni also possesses favorable stability in aqueous medium and rapid magnetic response to an external magnetic field. These make it a novel magnetic adsorbent for the separation/isolation of His6-tagged recombinant proteins from a complex sample matrix (cell lysate). The targeted protein species is captured onto the surface of the GP-Ni hybrid via specific metal affinity force between polyhistidine groups and nickel nanoparticles. The SDS-PAGE assay indicates highly selective separation of His6-tagged Smt A from cell lysate. The GP-Ni hybrid displays favorable performance on the separation/isolation of His6-tagged recombinant proteins with respect to the commercial NTA-Ni2+ column.

Nickel-tolerant ectomycorrhizal Pisolithus albus ultramafic ecotype isolated from nickel mines in New Caledonia strongly enhance growth of the host plant Eucalyptus globulus at toxic nickel concentrations.

Science.gov (United States)

Jourand, Philippe; Ducousso, Marc; Reid, Robert; Majorel, Clarisse; Richert, Clément; Riss, Jennifer; Lebrun, Michel

2010-10-01

Ectomycorrhizal (ECM) Pisolithus albus (Cooke & Massee), belonging to the ultramafic ecotype isolated in nickel-rich serpentine soils from New Caledonia (a tropical hotspot of biodiversity) and showing in vitro adaptive nickel tolerance, were inoculated to Eucalyptus globulus Labill used as a Myrtaceae plant-host model to study ectomycorrhizal symbiosis. Plants were then exposed to a nickel (Ni) dose-response experiment with increased Ni treatments up to 60 mg kg( - )(1) soil as extractable Ni content in serpentine soils. Results showed that plants inoculated with ultramafic ECM P. albus were able to tolerate high and toxic concentrations of Ni (up to 60 μg g( - )(1)) while uninoculated controls were not. At the highest Ni concentration tested, root growth was more than 20-fold higher and shoot growth more than 30-fold higher in ECM plants compared with control plants. The improved growth in ECM plants was associated with a 2.4-fold reduction in root Ni concentration but a massive 60-fold reduction in transfer of Ni from root to shoots. In vitro, P. albus strains could withstand high Ni concentrations but accumulated very little Ni in its tissue. The lower Ni uptake by mycorrhizal plants could not be explained by increased release of metal-complexing chelates since these were 5- to 12-fold lower in mycorrhizal plants at high Ni concentrations. It is proposed that the fungal sheath covering the plant roots acts as an effective barrier to limit transfer of Ni from soil into the root tissue. The degree of tolerance conferred by the ultramafic P. albus isolates to growth of the host tree species is considerably greater than previously reported for other ECM. The primary mechanisms underlying this improved growth were identified as reduced Ni uptake into the roots and markedly reduced transfer from root to shoot in mycorrhizal plants. The fact that these positive responses were observed at Ni concentrations commonly observed in serpentinic soils suggests that

First-principle study of structure and stability of nickel carbides

Energy Technology Data Exchange (ETDEWEB)

Gibson, Josh S; Uddin, Jamal; Cundari, Thomas R; Bodiford, Nelli K; Wilson, Angela K [Center for Advanced Scientific Computing and Modeling, University of North Texas, Denton, TX 76203 (United States); Department of Chemistry, University of North Texas, 1155 Union Circle 305070, Denton, TX 76203 (United States)

2010-10-10

Computational studies of nickel carbides, particularly Ni{sub 2}C, are scarce. A systematic density functional theory study is reported for Ni{sub 2}C, along with NiC and Ni{sub 3}C, to understand the stability and electronic structure of nickel carbides of varying stoichiometry. A comprehensive study was executed that involved 28 trial structures of varying space group symmetry for Ni{sub 2}C. An analysis of the electronic structure, geometry and thermodynamics of Ni{sub 2}C is performed, and compared with that for Ni{sub 3}C and NiC as well as several defect structures of varying composition. It is found that the most stable ground state arrangement of Ni{sub 2}C exists within a simple orthorhombic lattice and that it has metallic character. The calculated formation energies (kcal mol{sup -1}) of NiC, Ni{sub 2}C, and Ni{sub 3}C are 48.6, 7.9 and 6.4, respectively.

Synthesis, Structure, Characterization, and Decomposition of Nickel Dithiocarbamates: Effect of Precursor Structure and Processing Conditions on Solid-State Products

Science.gov (United States)

Hepp, Aloysius F.; Kulis, Michael J.; McNatt, Jeremiah S.; Duffy, Norman V.; Hoops, Michael D.; Gorse, Elizabeth; Fanwick, Philip E.; Masnovi, John; Cowen, Jonathan E.; Dominey, Raymond N.

2016-01-01

Single-crystal X-ray structures of four nickel dithiocarbamate complexes, the homoleptic mixed-organic bis-dithiocarbamates Ni[S2CN(isopropyl)(benzyl)]2, Ni[S2CN(ethyl)(n-butyl)]2, and Ni[S2CN(phenyl)(benzyl)]2, as well as the heteroleptic mixed-ligand complex NiCl[P(phenyl)3][(S2CN(phenyl)(benzyl)], were determined. Synthetic, spectroscopic, structural, thermal, and sulfide materials studies are discussed in light of prior literature. The spectroscopic results are routine. A slightly distorted square-planar nickel coordination environment was observed for all four complexes. The organic residues adopt conformations to minimize steric interactions. Steric effects also may determine puckering, if any, about the nickel and nitrogen atoms, both of which are planar or nearly so. A trans-influence affects the Ni-S bond distances. Nitrogen atoms interact with the CS2 carbons with a bond order of about 1.5, and the other substituents on nitrogen display transoid conformations. There are no strong intermolecular interactions, consistent with prior observations of the volatility of nickel dithiocarbamate complexes. Thermogravimetric analysis of the homoleptic species under inert atmosphere is consistent with production of 1:1 nickel sulfide phases. Thermolysis of nickel dithiocarbamates under flowing nitrogen produced hexagonal or -NiS as the major phase; thermolysis under flowing forming gas produced millerite (-NiS) at 300 C, godlevskite (Ni9S8) at 325 and 350 C, and heazlewoodite (Ni3S2) at 400 and 450 C. Failure to exclude oxygen results in production of nickel oxide. Nickel sulfide phases produced seem to be primarily influenced by processing conditions, in agreement with prior literature. Nickel dithiocarbamate complexes demonstrate significant promise to serve as single-source precursors to nickel sulfides, a quite interesting family of materials with numerous potential applications.

Assaying environmental nickel toxicity using model nematodes.

Directory of Open Access Journals (Sweden)

David Rudel

Full Text Available Although nickel exposure results in allergic reactions, respiratory conditions, and cancer in humans and rodents, the ramifications of excess nickel in the environment for animal and human health remain largely undescribed. Nickel and other cationic metals travel through waterways and bind to soils and sediments. To evaluate the potential toxic effects of nickel at environmental contaminant levels (8.9-7,600 µg Ni/g dry weight of sediment and 50-800 µg NiCl2/L of water, we conducted assays using two cosmopolitan nematodes, Caenorhabditis elegans and Pristionchus pacificus. We assayed the effects of both sediment-bound and aqueous nickel upon animal growth, developmental survival, lifespan, and fecundity. Uncontaminated sediments were collected from sites in the Midwestern United States and spiked with a range of nickel concentrations. We found that nickel-spiked sediment substantially impairs both survival from larval to adult stages and adult longevity in a concentration-dependent manner. Further, while aqueous nickel showed no adverse effects on either survivorship or longevity, we observed a significant decrease in fecundity, indicating that aqueous nickel could have a negative impact on nematode physiology. Intriguingly, C. elegans and P. pacificus exhibit similar, but not identical, responses to nickel exposure. Moreover, P. pacificus could be tested successfully in sediments inhospitable to C. elegans. Our results add to a growing body of literature documenting the impact of nickel on animal physiology, and suggest that environmental toxicological studies could gain an advantage by widening their repertoire of nematode species.

Characterization of nickel nanocones routed by electrodeposition without any template.

Science.gov (United States)

Hang, Tao; Li, Ming; Fei, Qin; Mao, Dali

2008-01-23

This work reports the synthesis of Ni nanocones by a one-step electrodeposition method without any template. With the addition of ethylenediamine dihydrochloride (EDA·2HCl) in the nickel plating solution, the novel Ni conical structure can be easily deposited onto different metal surfaces. The as-prepared nickel nanocones grow preferentially along [Formula: see text] directions with very sharp tips. The conical structures are single crystalline without any disruption of the lattice planes. In addition, the Ni nanocone structure is demonstrated to show magnetocrystalline anisotropy and enhance the magnetic properties when compared with other Ni nanostructures.

Impact of nickel (Ni) on hematological parameters and behavioral ...

African Journals Online (AJOL)

Jane

2011-10-17

Oct 17, 2011 ... The effect of nickel on hematological parameters and behaviour in Cyprinus carpio after a 96 h exposure to nickel test was investigated. .... important food item in human diet. Nickel is a natural element in the earth's makeup. This must be a factor in assessing its ability to harm the environment. Although,.

Reducing agent (NaBH{sub 4}) dependent structure, morphology and magnetic properties of nickel ferrite (NiFe{sub 2}O{sub 4}) nanorods

Energy Technology Data Exchange (ETDEWEB)

Saravanakumar, B.; Rani, B. Jansi; Ravi, G. [Nanomaterials Laboratory, Department of Physics, Alagappa University, Karaikudi 630 004, Tamil Nadu (India); Thambidurai, M. [Luminous Centre of Excellence for Semiconductor Lighting and Displays, School of Electrical & Electronic Engineering, The Photonics Institute (TPI), Nanyang Technological University, 50 Nanyang Avenue, 639798 (Singapore); Yuvakkumar, R., E-mail: yuvakkumar@gmail.com [Nanomaterials Laboratory, Department of Physics, Alagappa University, Karaikudi 630 004, Tamil Nadu (India)

2017-04-15

Nickel ferrite (Ni-Fe{sub 2}O{sub 4}) nanorods were synthesized employing a simple chemical reduction method. Reducing agent (NaBH{sub 4}) influence on structural, morphological and magnetic properties of NiFe{sub 2}O{sub 4} nanorods was investigated. XRD results clearly revealed the presence of inverse cubic spinel nickel ferrite structure characteristic peaks and confirmed the site inversion of inverse spinel structure of Fe{sup 3+} tetrahedral A site and Ni{sup 2+} octahedral B site. The observed Raman characteristic peak at 488 and 683 cm{sup −1} were corresponded to E{sub 1} {sub g} and A{sub 1} {sub g} mode whereas A and B site respectively corresponded to tetrahedral and octahedral site of NiFe{sub 2}O{sub 4} inverse spinel structure. The obtained PL peaks at 530 and 542 nm were attributed to the emission spectra of Fe{sup 3+} ions in site A of inverse spinel structure and Ni{sup 2+} ions in site B of inverse spinel structure respectively. SEM result clearly revealed that increase in NaBH{sub 4} concentration had remarkable impact on nanorods formation, nano-octahedron structure, homogeneity and regularity of Ni-Ferrites. VSM studies clearly revealed the soft ferromagnetic nature of NiFe{sub 2}O{sub 4} and increase in NaBH{sub 4} concentration further induced raise in metal cations concentration in A- and B- site which might impact the resultant magnetization of ferrites. - Highlights: • Nano rod formation has been initiated while increase of NaBH{sub 4} concentration. • Further increasing NaBH{sub 4} concentration favors nano-octahedron formation. • VSM studies revealed soft ferromagnetic nature of NiFe{sub 2}O{sub 4}.

A method for the determination of ascorbic acid using the iron(II)-pyridine-dimethylglyoxime complex

International Nuclear Information System (INIS)

Arya, S. P.; Mahajan, M.

1998-01-01

A simple and rapid spectrophotometric method for the determination of ascorbic acid is proposed. Ascorbic acid reduces iron (III) to iron (II) which forms a red colored complex with dimethylglyoxime in the presence of pyridine. The absorbance of the resulting solution is measured at 514 nm and a linear relationship between absorbance and concentration of ascorbic acid is observed up to 14 μg ml -1 . Studies on the interference of substances usually associated with ascorbic acid have been carried out and the applicability of the method has been tested by analysing pharmaceutical preparations of vitamin C [it

Sequential application of Fenton and ozone-based oxidation process for the abatement of Ni-EDTA containing nickel plating effluents.

Science.gov (United States)

Zhao, Zilong; Liu, Zekun; Wang, Hongjie; Dong, Wenyi; Wang, Wei

2018-07-01

Treatment of Ni-EDTA in industrial nickel plating effluents was investigated by integrated application of Fenton and ozone-based oxidation processes. Determination of integrated sequence found that Fenton oxidation presented higher apparent kinetic rate constant of Ni-EDTA oxidation and capacity for contamination load than ozone-based oxidation process, the latter, however, was favorable to guarantee the further mineralization of organic substances, especially at a low concentration. Serial-connection mode of two oxidation processes was appraised, Fenton effluent after treated by hydroxide precipitation and filtration negatively affected the overall performance of the sequential system, as evidenced by the removal efficiencies of Ni 2+ and TOC dropping from 99.8% to 98.7%, and from 74.8% to 66.6%, respectively. As a comparison, O 3 /Fe 2+ oxidation process was proved to be more effective than other processes (e.g. O 3 -Fe 2+ , O 3 /H 2 O 2 /Fe 2+ , O 3 /H 2 O 2 -Fe 2+ ), and the final effluent Ni 2+ concentration could satisfied the discharge standard (Fenton reaction, initial influent pH of 3.0, O 3 dosage of 252 mg L -1 , Fe 2+ of 150 mg L -1 , and reaction time of 30 min for O 3 /Fe 2+ oxidation). Furthermore, pilot-scale test was carried out to study the practical treatability towards the real nickel plating effluent, revealing the effective removal of some other co-existence contaminations. And Fenton reaction has contributed most, with the percentage ranging from 72.41% to 93.76%. The economic cost advantage made it a promising alternative to the continuous Fenton oxidation. Copyright © 2018 Elsevier Ltd. All rights reserved.

Stable nickel-substituted spinel cathode material (LiMn1.9Ni0.1O4) for lithium-ion batteries obtained by using a low temperature aqueous reduction technique

CSIR Research Space (South Africa)

Kunjuzwa, Niki

2016-11-01

Full Text Available A nickel substituted spinel cathode material (LiMn1.9Ni0.1O4) with enhanced electrochemical performance was successfully synthesized by using a locally-sourced, low-cost manganese precursor, electrolytic manganese dioxide (EMD), and NiSO4·6H2O as a...

Synthesis and structural features of resorcinol–formaldehyde resin chars containing nickel nanoparticles

International Nuclear Information System (INIS)

Galaburda, M.V.; Bogatyrov, V.M.; Skubiszewska-Zięba, J.; Oranska, O.I.; Sternik, D.; Gun’ko, V.M.

2016-01-01

Graphical abstract: - Highlights: • Facile synthesis of the Ni-doped carbon sorbents via carbonization of resorcinol–formaldehyde polymers/nickel(II) acetate mixtures in the inert atmosphere. • Effects of Ni content, as well as water volume and temperature treatment on the morphology and texture of the chars. • Ni/C composites are characterized by a core–shell structure with well-crystallized graphitic shells. • Ni content influences the structure of the carbon. • Nickel-doped carbon nanocomposites were used as a magnetically separable adsorbent. - Abstract: A series of meso- and microporous carbons containing magnetic Ni nanoparticles (Ni/C) with a variety of Ni loadings were synthesized by a simple one-pot procedure through carbonization of resorcinol–formaldehyde polymers containing various amounts of nickel(II) acetate. Such composite materials were characterized by N_2 sorption, Raman spectroscopy, X-ray diffraction (XRD), scanning electron microscopy (SEM) and Transmission electron microscope (TEM). The XRD patterns reveal peaks corresponding to face centered cubic nickel with the average size of crystallites of 17–18 nm. SEM and TEM results reveal that the formation of the nanoparticles took place mainly in the carbon spheres (1–2 μm in size) and on the outer surface as well. The as-prepared composites are characterized by a core–shell structure with well-crystallized graphitic shells about 8–15 nm in thickness. The Raman spectra show that Ni content influences the structure of the carbon. It was also shown that the morphology (particle shape and sizes) and porosity (pore volume and pore size distribution) of the chars are strongly dependent on water and nickel contents in the blends. One of the applications of Ni/C was demonstrated as a magnetically separable adsorbent.

Bisamidate and Mixed Amine/Amidate NiN2S2 Complexes as Models for Nickel-Containing Acetyl Coenzyme A Synthase and Superoxide Dismutase: An Experimental and Computational Study

International Nuclear Information System (INIS)

Mathrubootham, V.; Thomas, J.; Staples, R.; McCraken, J.; Shearer, J.; Hegg, E.

2010-01-01

The distal nickel site of acetyl-CoA synthase (Ni d -ACS) and reduced nickel superoxide dismutase (Ni-SOD) display similar square-planar Ni II N 2 S 2 coordination environments. One difference between these two sites, however, is that the nickel ion in Ni-SOD contains a mixed amine/amidate coordination motif while the Ni d site in Ni-ACS contains a bisamidate coordination motif. To provide insight into the consequences of the different coordination environments on the properties of the Ni ions, we systematically examined two square-planar Ni II N 2 S 2 complexes, one with bisthiolate-bisamidate ligation (Et 4 N) 2 (Ni(L1))·2H 2 O (2) (H 4 L1 = N-(2-mercaptoacetyl)-N(prime)-(2-mercaptoethyl)glycinamide) and another with bisthiolate-amine/amidate ligation K(Ni(HL2)) (3) (H 4 L2 = N-(2(double p rime)-mercaptoethyl)-2- ((2(prime)-mercaptoethyl)amino)acetamide). Although these two complexes differ only by a single amine versus amidate ligand, their chemical properties are quite different. The stronger in-plane ligand field in the bisamidate complex (Ni II (L1)) 2- (2) results in an increase in the energies of the d → d transitions and a considerably more negative oxidation potential. Furthermore, while the bisamidate complex (Ni II (L1)) 2- (2) readily forms a trinuclear species (Et 4 N) 2 ({Ni(L1)} 2 Ni)·H 2 O (1) and reacts rapidly with O 2 , presumably via sulfoxidation, the mixed amine/amidate complex (Ni II (HL2)) - (3) remains monomeric and is stable for days in air. Interestingly, the Ni III species of the bisamidate complex formed by chemical oxidation with I 2 can be detected by electron paramagnetic resonance (EPR) spectroscopy while the mixed amine/amidate complex immediately decomposes upon oxidation. To explain these experimentally observed properties, we performed S K-edge X-ray absorption spectroscopy and low-temperature (77 K) electronic absorption measurements as well as both hybrid density functional theory (hybrid-DFT) and spectroscopy oriented

Crystallite size effects in stacking faulted nickel hydroxide and its electrochemical behaviour

International Nuclear Information System (INIS)

Ramesh, T.N.

2009-01-01

β-Nickel hydroxide comprises a long range periodic arrangement of atoms with a stacking sequence of AC AC AC-having an ideal composition Ni(OH) 2 . Variation in the preparative conditions can lead to the changes in the stacking sequence (AC AC BA CB AC AC or AC AC AB AC AC). This type of variation in stacking sequence can result in the formation of stacking fault in nickel hydroxide. The stability of the stacking fault depends on the free energy content of the sample. Stacking faults in nickel hydroxide is essential for better electrochemical activity. Also there are reports correlating particle size to the better electrochemical activity. Here we present the effect of crystallite size on the stacking faulted nickel hydroxide samples. The electrochemical performance of stacking faulted nickel hydroxide with small crystallite size exchanges 0.8e/Ni, while the samples with larger crystallite size exchange 0.4e/Ni. Hence a right combination of crystallite size and stacking fault content has to be controlled for good electrochemical activity of nickel hydroxide

ELECTROCHEMICAL OXIDATION OF ETHANOL USING Ni-Co-PVC COMPOSITE ELECTRODE

Directory of Open Access Journals (Sweden)

Riyanto Riyanto

2011-07-01

Full Text Available The morphological characteristics and electrochemical behavior of nickel metal foil (Ni, nickel-polyvinyl chloride (Ni-PVC and nickel-cobalt-polyvinyl chloride (Ni-Co-PVC electrodes in alkaline solution has been investigated. The morphological characteristics of the electrode surface were studied using SEM and EDS, while the electrochemical behavior of the electrodes was studied using cyclic voltammetry (CV. It was found that composite electrodes (Ni-PVC and Ni-Co-PVC have a porous, irregular and rough surface. In situ studies using electrochemical technique using those three electrodes exhibited electrochemical activity for redox system, as well as selectivity in the electrooxidation of ethanol to acetic acid. The studies also found that an electrokinetics and electrocatalytic activity behaviors of the electrodes prepared were Ni metal foil

MOF-derived Co-doped nickel selenide/C electrocatalysts supported on Ni foam for overall water splitting

KAUST Repository

Ming, Fangwang; Liang, Hanfeng; Shi, Huanhuan; Xu, Xun; Mei, Gui; Wang, Zhoucheng

2016-01-01

It is of prime importance to develop dual-functional electrocatalysts with good activity for overall water splitting, which remains a great challenge. Herein, we report the synthesis of a Co-doped nickel selenide (a mixture of NiSe and NiSe)/C hybrid nanostructure supported on Ni foam using a metal-organic framework as the precursor. The resulting catalyst exhibits excellent catalytic activity toward the oxygen evolution reaction (OER), which only requires an overpotential of 275 mV to drive a current density of 30 mA cm. This overpotential is much lower than those reported for precious metal free OER catalysts. The hybrid is also capable of catalyzing the hydrogen evolution reaction (HER) efficiently. A current density of -10 mA cm can be achieved at 90 mV. In addition, such a hybrid nanostructure can achieve 10 and 30 mA cm at potentials of 1.6 and 1.71 V, respectively, along with good durability when functioning as both the cathode and the anode for overall water splitting in basic media.

MOF-derived Co-doped nickel selenide/C electrocatalysts supported on Ni foam for overall water splitting

KAUST Repository

Ming, Fangwang

2016-09-01

It is of prime importance to develop dual-functional electrocatalysts with good activity for overall water splitting, which remains a great challenge. Herein, we report the synthesis of a Co-doped nickel selenide (a mixture of NiSe and NiSe)/C hybrid nanostructure supported on Ni foam using a metal-organic framework as the precursor. The resulting catalyst exhibits excellent catalytic activity toward the oxygen evolution reaction (OER), which only requires an overpotential of 275 mV to drive a current density of 30 mA cm. This overpotential is much lower than those reported for precious metal free OER catalysts. The hybrid is also capable of catalyzing the hydrogen evolution reaction (HER) efficiently. A current density of -10 mA cm can be achieved at 90 mV. In addition, such a hybrid nanostructure can achieve 10 and 30 mA cm at potentials of 1.6 and 1.71 V, respectively, along with good durability when functioning as both the cathode and the anode for overall water splitting in basic media.

Synthesis of uniform-sized bimetallic iron-nickel phosphide nanorods

International Nuclear Information System (INIS)

Yoon, Ki Youl; Jang, Youngjin; Park, Jongnam; Hwang, Yosun; Koo, Bonil; Park, Je-Geun; Hyeon, Taeghwan

2008-01-01

We synthesized uniform-sized nanorods of iron-nickel phosphides from the thermal decomposition of metal-phosphine complexes. Uniform-sized (Fe x Ni 1-x ) 2 P nanorods (0≤x≤1) of various compositions were synthesized by thermal decomposition of Ni-trioctylphosphine (TOP) complex and Fe-TOP complex. By measuring magnetic properties, we found that blocking temperature and coercive field depend on Ni content in the nanorods. Both parameters were more sensitive to doping compared with bulk samples. - Graphical abstract: We synthesized uniform-sized nanorods of iron-nickel phosphides from thermal decomposition of metal-phosphine complexes. The magnetic studies showed that blocking temperature and coercive field depend on Ni content in the nanorods

Elucidating the mechanisms of nickel compound uptake: A review of particulate and nano-nickel endocytosis and toxicity

Energy Technology Data Exchange (ETDEWEB)

Muñoz, Alexandra; Costa, Max, E-mail: Max.Costa@nyumc.org

2012-04-01

Nickel (Ni) is a worldwide pollutant and contaminant that humans are exposed to through various avenues resulting in multiple toxic responses — most alarming is its clear carcinogenic nature. A variety of particulate Ni compounds persist in the environment and can be distinguished by characteristics such as solubility, structure, and surface charge. These characteristics influence cellular uptake and toxicity. Some particulate forms of Ni are carcinogenic and are directly and rapidly endocytized by cells. A series of studies conducted in the 1980s observed this process, and we have reanalyzed the results of these studies to help elucidate the molecular mechanism of particulate Ni uptake. Originally the process of uptake observed was described as phagocytosis, however in the context of recent research we hypothesize that the process is macropinocytosis and/or clathrin mediated endocytosis. Primary considerations in determining the route of uptake here include calcium dependence, particle size, and inhibition through temperature and pharmacological approaches. Particle characteristics that influenced uptake include size, charge, surface characteristics, and structure. This discussion is relevant in the context of nanoparticle studies and the emerging interest in nano-nickel (nano-Ni), where toxicity assessments require a clear understanding of the parameters of particulate uptake and where establishment of such parameters is often obscured through inconsistencies across experimental systems. In this regard, this review aims to carefully document one system (particulate nickel compound uptake) and characterize its properties.

Neutral, seven-coordinate dioxime complexes of technetium(III): Synthesis and characterization

International Nuclear Information System (INIS)

Linder, K.E.; Malley, M.F.; Gougoutas, J.Z.; Unger, S.E.; Nunn, A.D.

1990-01-01

The tin-capped complexes 99 Tc(oxime) 3 (μ-OH)SnCl 3 [oxime = dimethylglyoxime (DMG) or cyclohexanedione dioxime (CDO)] can be prepared by the reduction of NH 4 TcO 4 with 2 equiv of SnCl 2 in the presence of dioxime and HCl. These tin-capped complexes can be readily converted into a new class of uncapped Tc-dioxime compounds, TcCl(oxime) 3 , by treatment with HCl. This reaction is reversible. Both the tin-capped and uncapped tris(dioxime) complexes can be converted to the previously reported boron-capped Tc-dioxime complexes TcCl(oxime) 3 BR (R = alkyl, OH) by reaction with boronic acids or with boric acid at low pH. All of these complexes [Tc(oxime) 3 (μ-OH)SnCl 3 , TcCl(oxime) 3 , and TcCl(oxime) 3 BR] appear to be neutral, seven-coordinate compounds of technetium(III). They have been characterized by elemental analysis, 1 H NMR and UV/visible spectroscopy, conductivity, and fast atom bombardment mass spectrometry. The synthesis, characterization, and reactivity of these compounds is discussed. The x-ray crystal structure analysis of TcCl(DMG) 3 and an abbreviated structure report on TcCl(DMG) 3 MeB are described. Crystal data for TcCl(DMG) 3 are reported. 23 refs., 6 figs., 5 tabs

Hydrogen permeation inhibition by zinc-nickel alloy plating on steel XC68

International Nuclear Information System (INIS)

El Hajjami, A.; Gigandet, M.P.; De Petris-Wery, M.; Catonne, J.C.; Duprat, J.J.; Thiery, L.; Raulin, F.; Starck, B.; Remy, P.

2008-01-01

The inhibition of hydrogen permeation and barrier effect by zinc-nickel plating was investigated using the Devanathan-Stachurski permeation technique. The hydrogen permeation and hydrogen diffusion for the zinc-nickel (12-15%) plating on steel XC68 is compared with zinc and nickel. Hydrogen permeation and hydrogen diffusion were followed as functions of time at current density applied (cathodic side) and potential permanent (anodic side). The hydrogen permeation inhibition for zinc-nickel is intermediate to that of nickel and zinc. This inhibition was due to nickel-rich layer effects at the Zn-Ni alloy/substrate interface, is shown by GDOES. Zinc-nickel plating inhibited the hydrogen diffusion greater as compared to zinc. This diffusion resistance was due to the barrier effect caused by the nickel which is present at the interface and transformed the hydrogen atomic to Ni 2 H compound, as shown by GIXRD.

Hydrogen permeation inhibition by zinc-nickel alloy plating on steel XC68

Energy Technology Data Exchange (ETDEWEB)

El Hajjami, A. [Institut UTINAM, UMR CNRS 6213, Sonochimie et Reactivite des Surfaces, Universite de Franche-Comte, 16 route de Gray, 25030 Besancon Cedex (France); Coventya S.A.S., 51 rue Pierre, 92588 Clichy Cedex (France); Gigandet, M.P. [Institut UTINAM, UMR CNRS 6213, Sonochimie et Reactivite des Surfaces, Universite de Franche-Comte, 16 route de Gray, 25030 Besancon Cedex (France)], E-mail: marie-pierre.gigandet@univ-fcomte.fr; De Petris-Wery, M. [Institut Universitaire de Technologie d' Orsay, Universite Paris XI, Plateau de Moulon, 91400 Orsay (France); Catonne, J.C. [Professeur Honoraire du Conservatoire national des arts et metiers (CNAM), Paris (France); Duprat, J.J.; Thiery, L.; Raulin, F. [Coventya S.A.S., 51 rue Pierre, 92588 Clichy Cedex (France); Starck, B.; Remy, P. [Lisi Automotive, 28 faubourg de Belfort, BP 19, 90101 Delle Cedex (France)

2008-12-30

The inhibition of hydrogen permeation and barrier effect by zinc-nickel plating was investigated using the Devanathan-Stachurski permeation technique. The hydrogen permeation and hydrogen diffusion for the zinc-nickel (12-15%) plating on steel XC68 is compared with zinc and nickel. Hydrogen permeation and hydrogen diffusion were followed as functions of time at current density applied (cathodic side) and potential permanent (anodic side). The hydrogen permeation inhibition for zinc-nickel is intermediate to that of nickel and zinc. This inhibition was due to nickel-rich layer effects at the Zn-Ni alloy/substrate interface, is shown by GDOES. Zinc-nickel plating inhibited the hydrogen diffusion greater as compared to zinc. This diffusion resistance was due to the barrier effect caused by the nickel which is present at the interface and transformed the hydrogen atomic to Ni{sub 2}H compound, as shown by GIXRD.

Discharge capacity and microstructures of La Mg Pr Al Mn Co Ni alloys for nickel-metal hydride batteries

Energy Technology Data Exchange (ETDEWEB)

Casini, J.C.S.; Galdino, G.S.; Ferreira, E.A.; Takiishi, H.; Faria, R.N., E-mail: jcasini@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (DM/IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Dept. de Metalurgia

2010-07-01

La{sub 0.7-x}Mg{sub x}Pr{sub 0.3}Al{sub 0.3}Mn{sub 0.4}Co{sub 0.5}Ni{sub 3.8} (x = 0.0, 0.3 and 0.7) alloys have been investigated aiming the production of negative electrodes for nickel-metal hydride batteries. The alloys employed in this work were used in the as cast state. The results showed that the substitution of magnesium by lanthanum increased the discharge capacity of the Ni-MH batteries. A battery produced with the La{sub 0.4}Mg{sub 0.3}Pr{sub 0.3}Al{sub 0.3}Mn{sub 0.4}Co{sub 0.5}Ni{sub 3.8} alloy shown a high discharge capacity (380mAh/g) also good stability compared to other alloys. The electrode materials were characterized using scanning electron microscopy (SEM) and X-ray diffraction (XRD). (author)

Interaction of Nickel and Manganese in Accumulation and Localization in Leaves of the Ni Hyperaccumulators Alyssum murale and Alyssum corsicum

Energy Technology Data Exchange (ETDEWEB)

Broadhurst, C.; Tappero, R; Maugel, T; Erbe, E; Sparks, D; Chaney, R

2009-01-01

The genus Alyssum contains >50 Ni hyperaccumulator species; many can achieve >2.5% Ni in dry leaf. In soils with normal Mn levels, Alyssum trichome bases were previously observed to accumulate Ni and Mn to high levels. Here we report concentration and localization patterns in A. murale and A. corsicum grown in soils with nonphytotoxic factorial additions of Ni and Mn salts. Four leaf type subsets based on size and age accumulated Ni and Mn similarly. The greatest Mn accumulation (10 times control) was observed in A. corsicum with 40 mmol Mn kg-1 and 40 mmol Ni kg-1 added to potting soil. Whole leaf Ni concentrations decreased as Mn increased. Synchrotron X-ray fluorescence mapping of whole fresh leaves showed localized in distinct high-concentration Mn spots associated with trichomes, Ni and Mn distributions were strongly spatially correlated. Standard X-ray fluorescence point analysis/mapping of cryofractured and freeze-dried samples found that Ni and Mn were co-located and strongly concentrated only in trichome bases and in cells adjacent to trichomes. Nickel concentration was also strongly spatially correlated with sulfur. Results indicate that maximum Ni phytoextraction by Alyssum may be reduced in soils with higher phytoavailable Mn, and suggest that Ni hyperaccumulation in Alyssum species may have developed from a Mn handling system.

Effect of tetraethylthiuramdisulphide and diethyldithiocarbamate on nickel toxicokinetics in mice

International Nuclear Information System (INIS)

Dalsgaard, G.; Andersen, O.

1994-01-01

A new experimental pharmacokinetic model using the γ-emitting isotope 57 Ni for studying nickel toxicokinetics was employed in a recent investigation in order to quantitatively study, for the first time, the effect of tetraethylthiuram disulphide (disulfiram, Antabuse, TTD) and sodium diethyldithiocarbamate (DDC) on whole-body retention and organ distribution of nickel in mice. TTD or its decomposition product DDC given orally by stomach tube shortly after oral administration of a low dose of nickel chloride labelled with 57 Ni resulted in an approximately ten times higher whole-body retention of nickel compared to the retention in a control group exposed to nickel only. These chelators increased the whole-body retention of nickel also when given by intraperitoneal injection shortly after oral or intraperitoneal administration of nickel. Oral administration of a single dose of TTD or DDC rapidly after an oral dose of nickel chloride also resulted in extensive changes in the organ distribution of nickel, thus the nickel content in the brain was at least 700 times higher than in a control group given the same dose of nickel only. If DDC was given intraperitoneally after nickel given orally, the relative organ distribution of nickel to most organs was the same as if the chelator was given orally, though the contents of the liver and lungs were lower. That TTD and DDC resulted in a transport of nickel to the brain, is underlined by the fact that after 20 hr, approximately 15% and after 45-50 hr, 30% of the total body burden of Ni was found in the brain. Stating the nickel content as concentrations, we found after 19 hr to 23 hr the highest nickel concentration in the brain, kidneys, lungs and liver, in order of decreasing concentration. From 68 hr to 122 hr the order was brain, lungs, kidneys and liver. TTD and DDC are widely used clinically. These results indicate, that long-term simultaneous administration of nickel and TTD or DDC to humans should be avoided, as

Derivation of an oral toxicity reference value for nickel.

Science.gov (United States)

Haber, Lynne T; Bates, Hudson K; Allen, Bruce C; Vincent, Melissa J; Oller, Adriana R

2017-06-15

Nickel (Ni) is in the earth's crust and can be found in environmental compartments such as water, soil, and air, as well as food. This paper presents an assessment of the oral nickel toxicity data in support of non-cancer health-based oral exposure limits or toxicity reference values (TRVs). This paper derives TRVs for three populations of interest: adults, toddlers, and people who have been dermally sensitized to nickel. The adult/lifetime TRV of 20 μg Ni/kg-day is based on post-implantation loss/perinatal mortality in a 2-generation reproductive study in rats. Several recent assessments by regulatory agencies have used the same study and endpoint, but the dose-response modeling conducted here was more appropriate for the study design. Toxicokinetic data from rats and humans indicate that the applied uncertainty factors are very conservative. Because the endpoint relates to fetal exposure and is not relevant to toddlers, a toddler TRV was derived based on decreased body weight in young rats; this TRV was also 20 μg Ni/kg-day. A separate TRV of 4 μg Ni/kg in addition to Ni in food was derived for protection of nickel-sensitized populations from flare-up of dermatitis, based on studies of single exposures in humans under conditions that maximize oral absorption. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

Preparation and supercapacitor application of the single crystal nickel hydroxide and oxide nanosheets

Energy Technology Data Exchange (ETDEWEB)

Li, Qing [Department of Materials Science and Engineering, Yunnan University, 650091 Kunming (China); Ni, Haifang [Institute of Materials Science and Engineering, University of Science and Technology Beijing, 100083 Beijing (China); Cai, Yun; Cai, Xiaoyan [Department of Materials Science and Engineering, Yunnan University, 650091 Kunming (China); Liu, Yongjun [Advanced Analysis and Measurement Center, Yunnan University, 650091 Kunming (China); Chen, Gang [Department of Materials Science and Engineering, Yunnan University, 650091 Kunming (China); Fan, Li-Zhen, E-mail: fanlizhen@ustb.edu.cn [Institute of Materials Science and Engineering, University of Science and Technology Beijing, 100083 Beijing (China); Wang, Yude, E-mail: ydwang@ynu.edu.cn [Department of Materials Science and Engineering, Yunnan University, 650091 Kunming (China)

2013-09-01

Graphical abstract: The nickel hydroxide and nickel oxide nanosheets prepared using CTAB at room temperature exhibit a high specific capacitance, prompt charge/discharge rate. - Highlights: • The nickel hydroxide nanosheets were prepared using CTAB at room temperature. • Ni(OH){sub 2} nanosheet can be successfully converted to NiO nanosheet via calcination. • The NiO nanosheet has a specific capacitance of 388 F g{sup −1} at 5 A g{sup −1} in KOH solution. • Anneal temperature impacts capacitive properties as electrode. - Abstract: The single crystalline Ni(OH){sub 2} nanosheets were synthesized by a simple chemical precipitation method using nickel chloride as precursors and ammonia as precipitating agent. The Ni(OH){sub 2} nanosheets were successfully converted to NiO nanosheets via calcination under appropriate conditions. Analytical methods such as X-ray diffraction (XRD) spectra, scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution TEM (HRTEM), and Fourier transformed infrared (FTIR) spectra were employed to characterize the morphology and microstructure of the final products. The experimental results revealed that Ni(OH){sub 2} nanosheets were shape-preserved transformed to NiO nanosheets at 250 °C for 24 h. Ni(OH){sub 2} and NiO nanosheets were directly functionalized as supercapacitor electrodes for potential energy storage applications, whose charge–discharge properties, electrochemical impedance spectra, cyclic voltammetry, and cycle performance were examined. The experimental results show that the single-crystalline NiO nanosheets are a promising candidate for the supercapacitor electrode. They exhibit a high specific capacitance, prompt charge/discharge rate.

Reaction of nickel with uranium mononitride; Reaction du nickel avec le nitrure d'uranium

Energy Technology Data Exchange (ETDEWEB)

Anselin, F; Calais, D; Lorenzelli, N; Passefort, J C [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1965-07-01

UN-Ni system has been investigated in solid phase by diffusion couples UN-Ni or by mixed powders pressed and sintered. Studies have been carried out by micrography, X-rays and microanalysis with a CASTAING microprobe. UN-Ni compatibility is quite good up to 600 C; beyond this temperature diffusion zones corresponding to UNi{sub 5} and U{sub 2}N{sub 3} appear in the couples either reaction : 3 U N + 5 Ni {yields} U{sub 2}N{sub 3} + UNi{sub 5}; UN + 5 Ni {yields} UNi{sub 5}+ 1/2 N{sub 2} takes place from 700 C according to nitrogen pressure involved. For temperatures between 800 and 1000 C nickel solubility in uranium nitride is 1500 {+-} 500 wt ppm. (authors) [French] Le systeme UN-Ni a ete etudie par diffusion en phase solide a partir de couples (UN-Ni) ou de melanges pulverulents presses et frittes. Les techniques utilisees sont la micrographie, les rayons X et l'analyse ponctuelle a la microsonde de CASTAING. La compatibilite UN-Ni est bonne jusqu'a 600 C; au-dela il apparait dans les couples de diffusion des zones correspondant a UNi{sub 5} et U{sub 2}N{sub 3}. L'une ou l'autre des deux reactions: 3UN + 5 Ni {yields} U{sub 2}N{sub 3} + UNi{sub 5}; UN + 5 Ni {yields} UNi{sub 5} + 1/2 N{sub 2} se produisant des 700 C suivant la pression d'azote exercee. La solubilite du nickel dans le nitrure d'uranium pour des temperatures comprises entre 800 et 1000 C est de 1500 {+-} 500 ppm en poids. (auteurs)

Electroless nickel plating of arc discharge synthesized carbon nanotubes for metal matrix composites

International Nuclear Information System (INIS)

Jagannatham, M.; Sankaran, S.; Prathap, Haridoss

2015-01-01

Highlights: • Electroless Ni coatings have been performed on CNTs for various deposition times. • The deposition of nickel increased with increase in deposition time. • A deposition time of 60 min has been optimum for uniform coating of Ni on CNTs. • The CNTs with uniform coating of Ni are potential for reinforcements in composites. • Electroless nickel coatings are determined to be super paramagnetic behavior. - Abstract: Electroless nickel (EN) plating was performed on arc discharge synthesized multiwalled carbon nanotubes for various deposition times. X-ray diffraction (XRD), Transmission electron microscopy (TEM), and Raman spectroscopy characterization techniques are used to identify the presence of nickel deposition on the carbon nanotubes (CNTs) and the degree of graphitization. The results indicate that impurities are less in the purified CNTs as compared to raw carbon soot. Increasing deposition time up to 60 min increases uniform deposition of nickel throughout the length of the CNTs. However, for deposition time longer than 60 min, nickel particles are seen separated from the surface of the CNTs. Uniformly coated nickel CNTs throughout their length are potential candidates for reinforcements in composite materials. Magnetic properties of the nickel coated CNTs, with deposition time of 30 and 60 min were also evaluated. The magnetic saturation of nickel coated CNTs with deposition time of 30 min is less compared to nickel coated CNTs with deposition time of 60 min

Electroless nickel plating of arc discharge synthesized carbon nanotubes for metal matrix composites

Energy Technology Data Exchange (ETDEWEB)

Jagannatham, M.; Sankaran, S.; Prathap, Haridoss, E-mail: prathap@iitm.ac.in

2015-01-01

Highlights: • Electroless Ni coatings have been performed on CNTs for various deposition times. • The deposition of nickel increased with increase in deposition time. • A deposition time of 60 min has been optimum for uniform coating of Ni on CNTs. • The CNTs with uniform coating of Ni are potential for reinforcements in composites. • Electroless nickel coatings are determined to be super paramagnetic behavior. - Abstract: Electroless nickel (EN) plating was performed on arc discharge synthesized multiwalled carbon nanotubes for various deposition times. X-ray diffraction (XRD), Transmission electron microscopy (TEM), and Raman spectroscopy characterization techniques are used to identify the presence of nickel deposition on the carbon nanotubes (CNTs) and the degree of graphitization. The results indicate that impurities are less in the purified CNTs as compared to raw carbon soot. Increasing deposition time up to 60 min increases uniform deposition of nickel throughout the length of the CNTs. However, for deposition time longer than 60 min, nickel particles are seen separated from the surface of the CNTs. Uniformly coated nickel CNTs throughout their length are potential candidates for reinforcements in composite materials. Magnetic properties of the nickel coated CNTs, with deposition time of 30 and 60 min were also evaluated. The magnetic saturation of nickel coated CNTs with deposition time of 30 min is less compared to nickel coated CNTs with deposition time of 60 min.

Chemically grown, porous, nickel oxide thin-film for electrochemical supercapacitors

Energy Technology Data Exchange (ETDEWEB)

Inamdar, A.I.; Kim, YoungSam; Im, Hyunsik [Department of Semiconductor Science, Dongguk University, Seoul 100-715 (Korea, Republic of); Pawar, S.M.; Kim, J.H. [Department of Materials Science and Engineering, Chonnam National University, Gwangju 500-757 (Korea, Republic of); Kim, Hyungsang [Department of Physics, Dongguk University, Seoul 100-715 (Korea, Republic of)

2011-02-15

A porous nickel oxide film is successfully synthesized by means of a chemical bath deposition technique from an aqueous nickel nitrate solution. The formation of a rock salt NiO structure is confirmed with XRD measurements. The electrochemical supercapacitor properties of the nickel oxide film are examined using cyclic voltammetery (CV), galvanostatic and impedance measurements in two different electrolytes, namely, NaOH and KOH. A specific capacitance of {proportional_to}129.5 F g{sup -1} in the NaOH electrolyte and {proportional_to}69.8 F g{sup -1} in the KOH electrolyte is obtained from a cyclic voltammetery study. The electrochemical stability of the NiO electrode is observed for 1500 charge-discharge cycles. The capacitative behaviour of the NiO electrode is confirmed from electrochemical impedance measurements. (author)

Nickel metal with various morphologies: synthesis and performances for catalytic carbon dioxide reforming with methane.

Science.gov (United States)

Teabpinyok, Nopporn; Samingprai, Sutheerawat; Chareonpanich, Metta

2012-12-01

In this research, nickel metal of three different morphologies including nanostar, icosahedra, and microsphere structures were synthesized. It was found nanostar nickel revealed the Ni(111) crystallographic plane with particle size in the range of 150-200 nm and BET surface area of 13 m2/g. The icosahedra nickel also showed the Ni(111) crystallographic plane with larger particle size (300-400 nm) and BET surface area of 20 m2/g, whereas microsphere nickel exhibited the relatively large cluster size (approximately 3 microm) and BET surface area (114 m2/g) as a result of an aggregation of Ni(101) nanoplates. The obtained nickel catalysts were tested for the activity in carbon dioxide reforming with methane. Based on the similar specific surface area of catalysts, nanostar nickel showed the highest carbon dioxide and methane conversions due to its crystallographic structure. At 700 degrees C, nanostar nickel catalyst exhibited the highest carbon dioxide and methane conversions of 17.6 and 10.5 times higher than those of microsphere nickel catalyst, respectively.

Analysis of holding time variations to Ni and Fe content and morphology in nickel laterite limonitic reduction process by using coal-dolomite bed

Science.gov (United States)

Abdul, Fakhreza; Pintowantoro, Sungging; Yuwandono, Ridwan Bagus

2018-04-01

With the depletion of nickel sulfide ore resources, the nickel laterit processing become an attention to fulfill nickel world demans. Reducing laterite nickel by using a low cost carbonaceous reductan has proved produces high grade ferronickel alloy. In this research, reduction was carried out to low grade laterite nickel (limonite) with 1.25% nikel content by using CO gas reductant formed by reaction between coal and dolomite. Reduction process preceded by forming brickets mixture from limonit ore, coal, and Na2SO4, then the brickets placed inside crucible bed together with dolomit and reduced at temperature 1400 °C with holding time variations 4, 6, and 8 hours. EDX, XRD, and SEM test were carried out to find out the Ni and nickel grade after reduced, the phases that formed, and the morphology brickets after reduced. The reduction results shows that the highest increase on nickel grade was obtained by 8 hours holding time increasing 5.84 % from initial grade, and the highest recovery was obtained by 6 hours holding time with recovery 88.51 %. While the higest increase on Fe grade was obtained by 4 hours holding time, and the highest recovery Fe was obtained by 4 hours holding time with recovery 85.41%.

Hydrothermal synthesis of Ni_2P nanoparticle and its hydrodesulfurization of dibenzothiophene

International Nuclear Information System (INIS)

Zhao, Qi; Han, Yang; Huang, Xiang; Dai, Jinhui; Tian, Jintao; Zhu, Zhibin; Yue, Li

2017-01-01

Nanosized nickel phosphide (Ni_2P) has been synthesized via hydrothermal reaction with environmental-friendly red phosphorus and nickel chloride. The reaction mechanism has been studied by measurement techniques of IC, XRD ,TEM, EDS, and XPS. The results showed that the particle sizes of as-prepared Ni_2P are in nanoscale ranging from 10 to 30 nm. In hydrothermal reaction, red phosphorus reacts with water to its oxyacids, especially its hypophosphorous acid (or hypophosphite) which can reduce nickel chloride to nickel, and then metallic nickel will penetrate into the rest of red phosphorus to generate nano-Ni_2P. Furthermore, the catalytic performance of as-synthesized Ni_2P for the hydrodesulfurization of dibenzothiophene has been tested. It has been shown that the HDS reaction process over Ni_2P catalyst agrees well with the pseudo-first order kinetic equation, and the HDS conversion can reach up to 43.83% in 5 h with a stable increasing catalytic activity during the whole examination process.

Nickel speciation in cement-stabilized/solidified metal treatment filtercakes

Energy Technology Data Exchange (ETDEWEB)

Roy, Amitava, E-mail: reroy@lsu.edu [J. Bennett Johnston, Sr., Center for Advanced Microstructures and Devices, Louisiana State University, Baton Rouge, LA 70806, USA (United States); Stegemann, Julia A., E-mail: j.stegemann@ucl.ac.uk [Centre for Resource Efficiency & the Environment, Department of Civil, Environmental & Geomatic Engineering, University College London, Chadwick Building, Gower Street, London WC1E 6BT, UK (United Kingdom)

2017-01-05

Highlights: • XAS shows the same Ni speciation in untreated and stabilized/solidified filtercake. • Ni solubility is the same for untreated and stabilized/solidified filtercake. • Leaching is controlled by pH and physical encapsulation for all binders. - Abstract: Cement-based stabilization/solidification (S/S) is used to decrease environmental leaching of contaminants from industrial wastes. In this study, two industrial metal treatment filtercakes were characterized by X-ray diffractometry (XRD), thermogravimetric and differential thermogravimetric analysis (TG/DTG) and Fourier transform infrared (FTIR); speciation of nickel was examined by X-ray absorption (XAS) spectroscopy. Although the degree of carbonation and crystallinity of the two untreated filtercakes differed, α-nickel hydroxide was identified as the primary nickel-containing phase by XRD and nickel K edge XAS. XAS showed that the speciation of nickel in the filtercake was unaltered by treatment with any of five different S/S binder systems. Nickel leaching from the untreated filtercakes and all their stabilized/solidified products, as a function of pH in the acid neutralization capacity test, was essentially complete below pH ∼5, but was 3–4 orders of magnitude lower at pH 8–12. S/S does not respeciate nickel from metal treatment filtercakes and any reduction of nickel leaching by S/S is attributable to pH control and physical mechanisms only. pH-dependent leaching of Cr, Cu and Ni is similar for the wastes and s/s products, except that availability of Cr, Cu and Zn at decreased pH is reduced in matrices containing ground granulated blast furnace slag.

Preparation and characterization of a supported system of Ni2P/Ni12P5 nanoparticles and their use as the active phase in chemoselective hydrogenation of acetophenone

Science.gov (United States)

Costa, Dolly C.; Soldati, Analía L.; Pecchi, Gina; Bengoa, José Fernando; Marchetti, Sergio Gustavo; Vetere, Virginia

2018-05-01

Ni2P/Ni12P5 nanoparticles were obtained by thermal decomposition of nickel organometallic salt at low temperature. The use of different characterization techniques allowed us to determine that this process produced a mixture of two nickel phosphide phases: Ni2P and Ni12P5. These nickel phosphides nanoparticles, supported on mesoporous silica, showed activity and high selectivity for producing the hydrogenation of the acetophenone carbonyl group to obtain 1-phenylethanol. This is a first report that demonstrates the ability of supported Ni2P/Ni12P5 nanoparticles to produce the chemoselective hydrogenation of acetophenone. We attribute these special catalytic properties to the particular geometry of the Ni–P sites on the surface of the nanoparticles. This is an interesting result because the nickel phosphides have a wide composition range (from Ni3P to NiP3), with different crystallographic structures, therefore we think that different phases could be active and selective to hydrogenate many important molecules with more than one functional group.

Progress in the Development of Lightweight Nickel Electrode for Nickel-Hydrogen Cell

Science.gov (United States)

Britton, Doris L.

1999-01-01

Development of a high specific energy battery is one of the objectives of the lightweight nickel-hydrogen (Ni-H2) program at the NASA Glenn Research Center. The approach has been to improve the nickel electrode by continuing combined in-house and contract efforts to develop a lighter weight electrode for the nickel-hydrogen cell. Small fiber diameter nickel plaques are used as conductive supports for the nickel hydroxide active material. These plaques are commercial products and have an advantage of increased surface area available for the deposition of active material. Initial tests include activation and capacity measurements at five different discharge levels, C/2, 1.0 C, 1.37 C, 2.0 C, and 2.74 C. The electrodes are life cycle tested using a half-cell configuration at 40 and 80% depths-of-discharge (DOD) in a low-Earth-orbit regime. The electrodes that pass the initial tests are life cycle-tested in a boiler plate nickel-hydrogen cell before flight weight design are built and tested.

Comparison of inorganic inhibitors of copper, nickel and copper-nickels in aqueous lithium bromide solution

International Nuclear Information System (INIS)

Munoz, A. Igual; Anton, J. Garcia; Guin-tilde on, J.L.; Herranz, V. Perez

2004-01-01

The electrochemical behavior of copper, nickel and two copper-nickel (Cu90/Ni10 and Cu70/Ni30) alloys in 850 g/L LiBr solution in the absence and presence of three different inorganic inhibitors (chromate CrO 4 2- , molybdate MoO 4 2- , and tetraborate B 4 O 7 2- ) has been studied. Differences in inhibition efficiency are discussed in terms of potentiodynamic and cyclic measurements. The best protection is obtained by adding chromate to the 850 g/L LiBr solution while the inhibition efficiencies of molybdate and tetraborate ions were not markedly high. Very aggressive anions, such as bromides, in the present experimental conditions, notably reduce the action of the less efficient molecules (molybdate and tetraborate), but not that of the most efficient ones (chromate). The results of the investigation show that the inhibiting properties depend on the nickel content in the alloy; this element improves the general corrosion resistance of the material in the sense that it shifts free corrosion potential towards more noble values and density corrosion currents towards lower levels. The nickel content in the alloy also enlarges the passivating region of the materials in chromate and molybdate-containing solution; furthermore it decreases the current passivating values to lower values. Nickel addition improves the localized corrosion resistance in the bromide media

Absorption and retention of nickel from drinking water in relation to food intake and nickel sensitivity

DEFF Research Database (Denmark)

Nielsen, G D; Søderberg, U; Jørgensen, Poul Jørgen

1999-01-01

nickel in drinking water (12 micrograms Ni/kg) and, at different time intervals, standardized 1400-kJ portions of scrambled eggs. When nickel was ingested in water 30 min or 1 h prior to the meal, peak nickel concentrations in serum occurred 1 h after the water intake, and the peak was 13-fold higher...... than the one seen 1 h after simultaneous intake of nickel-containing water and scrambled eggs. In the latter case, a smaller, delayed peak occurred 3 h after the meal. Median urinary nickel excretion half-times varied between 19.9 and 26.7 h. Within 3 days, the amount of nickel excreted corresponded...... to 2.5% of the nickel ingested when it was mixed into the scrambled eggs. Increasing amounts were excreted as the interval between the water and the meal increased, with 25.8% of the administered dose being excreted when the eggs were served 4 h prior to the nickel-containing drinking water...

Electrodeposition of Manganese-Nickel Oxide Films on a Graphite Sheet for Electrochemical Capacitor Applications

Directory of Open Access Journals (Sweden)

Hae-Min Lee

2014-01-01

Full Text Available Manganese-nickel (Mn-Ni oxide films were electrodeposited on a graphite sheet in a bath consisting of manganese acetate and nickel chloride, and the structural, morphological, and electrochemical properties of these films were investigated. The electrodeposited Mn-Ni oxide films had porous structures covered with nanofibers. The X-ray diffractometer pattern revealed the presence of separate manganese oxide (g-MnO2 and nickel oxide (NiO in the films. The electrodeposited Mn-Ni oxide electrode exhibited a specific capacitance of 424 F/g in Na2SO4 electrolyte. This electrode maintained 86% of its initial specific capacitance over 2000 cycles of the charge-discharge operation, showing good cycling stability.

The Effect of Annealing Temperature on Nickel on Reduced Graphene Oxide Catalysts on Urea Electrooxidation

International Nuclear Information System (INIS)

Glass, Dean E.; Galvan, Vicente; Prakash, G.K. Surya

2017-01-01

Highlights: •Nickel was reduced on graphene oxide and annealed under argon from 300 to 700 °C. •Nickel was oxidized from the removal of oxygen groups on the graphene oxide. •Higher annealed catalysts displayed decreased urea electrooxidation currents. •Micro direct urea/hydrogen peroxide fuel cells were employed for the first time. •Ni/rGO catalysts displayed enhanced fuel cell performance than the bare nickel. -- Abstract: The annealing temperature effects on nickel on reduced graphene oxide (Ni/rGO) catalysts for urea electrooxidation were investigated. Nickel chloride was directly reduced in an aqueous solution of graphene oxide (GO) followed by annealing under argon at 300, 400, 500, 600, and 700 °C, respectively. X-ray Diffraction (XRD) patterns revealed an increase in the crystallite size of the nickel nanoparticles while the Raman spectra displayed an increase in the graphitic disorder of the reduced graphene oxide at higher annealing temperatures due to the removal of oxygen functional groups. The Ni/rGO catalysts annealed at higher temperatures displayed oxidized nickel surface characteristics from the Ni 2p X-ray Photoelectron Spectra (XPS) due to the oxidation of the nickel from the oxygen functional groups in the graphitic lattice. In the half-cell testing, the onset potential of urea electrooxidation decreased while the urea electrooxidation currents decreased as the annealing temperature was increased. The nickel catalyst annealed at 700 °C displayed a 31% decrease in peak power density while the catalyst annealed at 300 °C displayed a 13% increase compared with the unannealed Ni/rGO catalyst in the micro direct urea/hydrogen peroxide fuel cells tests.

Polymer stabilized Ni-Ag and Ni-Fe alloy nanoclusters: Structural and magnetic properties

Energy Technology Data Exchange (ETDEWEB)

Kabir, L.; Mandal, A.R. [Department of Physics, Visva-Bharati, Santiniketan-731 235 (India); Mandal, S.K., E-mail: sk_mandal@hotmail.co [Department of Physics, Visva-Bharati, Santiniketan-731 235 (India)

2010-04-15

We report here the structural and magnetic behaviors of nickel-silver (Ni-Ag) and nickel-iron (Ni-Fe) nanoclusters stabilized with polymer (polypyrrole). High resolution transmission electron microscopy (HRTEM) indicates Ni-Ag nanoclusters to stabilize in core-shell configuration while that of Ni-Fe nanoclusters in a mixed type of geometry. Structural characterizations by X-ray diffraction (XRD) reveal the possibility of alloying in such bimetallic nanoclusters to some extent even at temperatures much lower than that of bulk alloying. Electron paramagnetic resonance (EPR) spectra clearly reveal two different absorption behaviors: one is ascribed to non-isolated Ni{sup 2+} clusters surrounded by either silver or iron giving rise to a broad signal, other (very narrow signal) being due to the isolated superparamagnetic Ni{sup 2+} clusters or bimetallic alloy nanoclusters. Results obtained for Ni-Ag and Ni-Fe nanoclusters have been further compared with the behavior exhibited by pure Ni nanoclusters in polypyrrole host. Temperature dependent studies (at 300 and 77 K) of EPR parameters, e.g. linewidth, g-value, line shape and signal intensity indicating the significant influence of surrounding paramagnetic silver or ferromagnetic iron within polymer host on the EPR spectra have been presented.

Polymer stabilized Ni-Ag and Ni-Fe alloy nanoclusters: Structural and magnetic properties

Science.gov (United States)

Kabir, L.; Mandal, A. R.; Mandal, S. K.

2010-04-01

We report here the structural and magnetic behaviors of nickel-silver (Ni-Ag) and nickel-iron (Ni-Fe) nanoclusters stabilized with polymer (polypyrrole). High resolution transmission electron microscopy (HRTEM) indicates Ni-Ag nanoclusters to stabilize in core-shell configuration while that of Ni-Fe nanoclusters in a mixed type of geometry. Structural characterizations by X-ray diffraction (XRD) reveal the possibility of alloying in such bimetallic nanoclusters to some extent even at temperatures much lower than that of bulk alloying. Electron paramagnetic resonance (EPR) spectra clearly reveal two different absorption behaviors: one is ascribed to non-isolated Ni 2+ clusters surrounded by either silver or iron giving rise to a broad signal, other (very narrow signal) being due to the isolated superparamagnetic Ni 2+ clusters or bimetallic alloy nanoclusters. Results obtained for Ni-Ag and Ni-Fe nanoclusters have been further compared with the behavior exhibited by pure Ni nanoclusters in polypyrrole host. Temperature dependent studies (at 300 and 77 K) of EPR parameters, e.g. linewidth, g-value, line shape and signal intensity indicating the significant influence of surrounding paramagnetic silver or ferromagnetic iron within polymer host on the EPR spectra have been presented.

Polymer stabilized Ni-Ag and Ni-Fe alloy nanoclusters: Structural and magnetic properties

International Nuclear Information System (INIS)

Kabir, L.; Mandal, A.R.; Mandal, S.K.

2010-01-01

We report here the structural and magnetic behaviors of nickel-silver (Ni-Ag) and nickel-iron (Ni-Fe) nanoclusters stabilized with polymer (polypyrrole). High resolution transmission electron microscopy (HRTEM) indicates Ni-Ag nanoclusters to stabilize in core-shell configuration while that of Ni-Fe nanoclusters in a mixed type of geometry. Structural characterizations by X-ray diffraction (XRD) reveal the possibility of alloying in such bimetallic nanoclusters to some extent even at temperatures much lower than that of bulk alloying. Electron paramagnetic resonance (EPR) spectra clearly reveal two different absorption behaviors: one is ascribed to non-isolated Ni 2+ clusters surrounded by either silver or iron giving rise to a broad signal, other (very narrow signal) being due to the isolated superparamagnetic Ni 2+ clusters or bimetallic alloy nanoclusters. Results obtained for Ni-Ag and Ni-Fe nanoclusters have been further compared with the behavior exhibited by pure Ni nanoclusters in polypyrrole host. Temperature dependent studies (at 300 and 77 K) of EPR parameters, e.g. linewidth, g-value, line shape and signal intensity indicating the significant influence of surrounding paramagnetic silver or ferromagnetic iron within polymer host on the EPR spectra have been presented.

Corrosion resistance of nickel alloys with chromium and silicon to the red fuming nitric acid

International Nuclear Information System (INIS)

Gurvich, L.Ya.; Zhirnov, A.D.

1994-01-01

Corrosion and electrochemical behaviour of binary Ni-Cr, Ni-Si nickel and ternary Ni-Cr-Si alloys in the red fuming nitric acid (RFNA) (8-% of HNO 3 +20% of N 2 O 4 ) is studied. It is shown that nickel alloying with chromium improves its corrosion resistance to the red fuming nitric acid. Nickel alloying with silicon in quantities of up to 5 % reduces, and up to 10%-increases abruptly the corrosion resistance with subsequent decrease of the latter after the further increase of concentration. Ni-15% of Cr alloy alloying with silicon increases monotonously the corrosion resistance. 10 refs., 7 figs., 3 tabs

Chemical yield determination for 59Ni, 63Ni and 56Fe in low and intermediate nuclear wastes by ICP-AES

International Nuclear Information System (INIS)

Franco, Milton B.; Santos Neto, Francisco C. dos; Reis Junior, Aluisio S.; Temba, Eliane S.C.; Monteiro, Roberto P.G.

2011-01-01

Iron and nickel are constituents of a wide range of metallic materials used in nuclear reactor construction and their corresponding activation products are often encountered in reactor-derived solid low and intermediate-level wastes. The most significant radioisotopes of iron and nickel, in terms of quantity and half life, are 55 Fe (t 1/2 =2.73y), 59 Ni (t 1/2 =7.6x10 4 y) and 63 Ni (t 1/2 =10 2 y) and they are activation products of stable iron and nickel. 59 Ni is an X-ray - emitting and 55 Fe and 63 Ni are β-particle-emitting radionuclides and so they are radionuclides of interest for the performance of assessment studies of waste storage or disposal. For their determination in the radioactive wastes is necessary to know the chemical yield for the radiochemical separation procedures prior analytical measurements. In this work Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES) technique was used for this aim. Total nickel and iron in waste samples from nuclear power plants were determined before and after the radiochemical separation at specific wavelengths, 231.604 nm and 259.940 nm respectively. The chemical yields for nickel and iron recovery were around 82 % for iron and 59 % for nickel according the analytical methodology adopted. (author)

Interfacial microstructure and mechanical properties of diffusion-bonded titanium-stainless steel joints using a nickel interlayer

International Nuclear Information System (INIS)

Kundu, S.; Chatterjee, S.

2006-01-01

Diffusion bonding was carried out between commercially pure titanium and 304 stainless steel using nickel interlayer in the temperature range of 800-950 deg. C for 3.6 ks under 3 MPa load in vacuum. The transition joints thus formed were characterized in optical and scanning electron microscopes. TiNi 3 , TiNi and Ti 2 Ni are formed at the nickel-titanium (Ni-Ti) interface; whereas, stainless steel-nickel (SS-Ni) interface is free from intermetallic compounds up to 900 deg. C processing temperatures. At 950 deg. C, Ni-Ti interface exhibits the presence of β-Ti discrete islands in the matrix of Ti 2 Ni and the phase mixture of λ + χ + α-Fe, λ + α-Fe, λ + FeTi + β-Ti and FeTi + β-Ti occurs at the stainless steel-nickel interface. Nickel is able to inhibit the diffusion of Ti to stainless steel side up to 900 deg. C temperature; however, becomes unable to restrict the migration of Ti to stainless steel at 950 deg. C. Bond strength was also evaluated and maximum tensile strength of ∼302 MPa and shear strength of ∼219 MPa were obtained for the diffusion couple processed at 900 deg. C temperature due to better contact of the mating surfaces and failure takes place at the Ni-Ti interface. At higher joining temperature, the formation of Fe-Ti bases intermetallics reduces the bond strength and failure occurs at the SS-Ni interface

Surfactant-assisted ultrasonic spray pyrolysis of nickel oxide and lithium-doped nickel oxide thin films, toward electrochromic applications

Energy Technology Data Exchange (ETDEWEB)

Denayer, Jessica [Group of Research in Energy and Environment for MATerials (GREENMAT), University of Liège, allée de la chimie 3, 4000 Liège (Belgium); Bister, Geoffroy [Environmental and Material Research Association (CRIBC-INISMa), avenue gouverneur cornez 4, 7000 Mons (Belgium); Simonis, Priscilla [Laboratory LPS, University of Namur, rue de bruxelles 61, 5000 Namur (Belgium); Colson, Pierre; Maho, Anthony [Group of Research in Energy and Environment for MATerials (GREENMAT), University of Liège, allée de la chimie 3, 4000 Liège (Belgium); Aubry, Philippe [Environmental and Material Research Association (CRIBC-INISMa), avenue gouverneur cornez 4, 7000 Mons (Belgium); Vertruyen, Bénédicte [Group of Research in Energy and Environment for MATerials (GREENMAT), University of Liège, allée de la chimie 3, 4000 Liège (Belgium); Henrist, Catherine, E-mail: catherine.henrist@ulg.ac.be [Group of Research in Energy and Environment for MATerials (GREENMAT), University of Liège, allée de la chimie 3, 4000 Liège (Belgium); Lardot, Véronique; Cambier, Francis [Environmental and Material Research Association (CRIBC-INISMa), avenue gouverneur cornez 4, 7000 Mons (Belgium); Cloots, Rudi [Group of Research in Energy and Environment for MATerials (GREENMAT), University of Liège, allée de la chimie 3, 4000 Liège (Belgium)

2014-12-01

Highlights: • Surfactant-assisted USP: a novel and low cost process to obtain high quality nickel oxide films, with or without lithium dopant. • Increased uniformity and reduced light scattering thanks to the addition of a surfactant. • Improved electrochromic performance (coloration efficiency and contrast) for lithium-doped films by comparison with the undoped NiO film. - Abstract: Lithium-doped nickel oxide and undoped nickel oxide thin films have been deposited on FTO/glass substrates by a surfactant-assisted ultrasonic spray pyrolysis. The addition of polyethylene glycol in the sprayed solution has led to improved uniformity and reduced light scattering compared to films made without surfactant. Furthermore, the presence of lithium ions in NiO films has resulted in improved electrochromic performances (coloration contrast and efficiency), but with a slight decrease of the electrochromic switching kinetics.

The effect of current density and saccharin addition on the grain size of nickel coatings

Energy Technology Data Exchange (ETDEWEB)

Uhm, Young Rang; Park, Keun Yung; Son, Kwang Jae; Shim, Young Ho; Choi, Sun Ju [KAERI, Daejeon (Korea, Republic of)

2012-10-15

Recently, the main advantage of a radioisotope 'fuel' is concentrated, because it is 'burned' at the rate of the isotopes half life. In other words, given a half life of 100 years, a nuclear battery would still produce half of its initial starting power after 100 years. A speck of a radioisotope like nickel 63, for example, contains enough energy to power a nano nuclear battery for decades, and to do so safely. Ni 63, a beta radiation source, is prepared by electrical deposition of radioactive Ni 63 ions on thin non radioactive nickel foil. Ni 63 plating is similar to other electroplating processes that employ soluble metal anodes. It requires the passage of a direct current between two electrodes that are immersed in a conductive, aqueous solution of nickel salts. The charged Ni ions are formed by sulfate, sulfamate, chloride, and a Watts bath. However, the charged Ni 63 ions are formed by dissolving metal Ni 63. To establish the coating condition of Ni 63, non radioactive metal Ni particles were dissolved in an acid solution and electroplated on the Ni sheet. A continuous increase in the grain size versus current density has also been recognized in the direct current electrodeposition of nickel coating. On the other hand, A runa et al. reported that the current density has no significant effect on the grain size of nickel electro deposits. A review of the literature shows that saccharin has often been added to a nickel plating bath since the 1980s to improve the ductility and brightness, and in later periods as a grain refiner agent. In the present paper, not only the preparation of the Ni plating solution prepared by dissolving metal particles but also an optimization of the deposition conditions, such as the influence of current density and saccharin concentration on the grain size, was investigated. The proposed model can also be applied for radioactive Ni 63 electroplating.

The effect of current density and saccharin addition on the grain size of nickel coatings

International Nuclear Information System (INIS)

Uhm, Young Rang; Park, Keun Yung; Son, Kwang Jae; Shim, Young Ho; Choi, Sun Ju

2012-01-01

Recently, the main advantage of a radioisotope 'fuel' is concentrated, because it is 'burned' at the rate of the isotopes half life. In other words, given a half life of 100 years, a nuclear battery would still produce half of its initial starting power after 100 years. A speck of a radioisotope like nickel 63, for example, contains enough energy to power a nano nuclear battery for decades, and to do so safely. Ni 63, a beta radiation source, is prepared by electrical deposition of radioactive Ni 63 ions on thin non radioactive nickel foil. Ni 63 plating is similar to other electroplating processes that employ soluble metal anodes. It requires the passage of a direct current between two electrodes that are immersed in a conductive, aqueous solution of nickel salts. The charged Ni ions are formed by sulfate, sulfamate, chloride, and a Watts bath. However, the charged Ni 63 ions are formed by dissolving metal Ni 63. To establish the coating condition of Ni 63, non radioactive metal Ni particles were dissolved in an acid solution and electroplated on the Ni sheet. A continuous increase in the grain size versus current density has also been recognized in the direct current electrodeposition of nickel coating. On the other hand, A runa et al. reported that the current density has no significant effect on the grain size of nickel electro deposits. A review of the literature shows that saccharin has often been added to a nickel plating bath since the 1980s to improve the ductility and brightness, and in later periods as a grain refiner agent. In the present paper, not only the preparation of the Ni plating solution prepared by dissolving metal particles but also an optimization of the deposition conditions, such as the influence of current density and saccharin concentration on the grain size, was investigated. The proposed model can also be applied for radioactive Ni 63 electroplating

Effect of charge state and stoichiometry on the structure and reactivity of nickel oxide clusters with CO

Science.gov (United States)

Johnson, Grant E.; Reilly, Nelly M.; Castleman, A. W., Jr.

2009-02-01

The collision induced fragmentation and reactivity of cationic and anionic nickel oxide clusters with carbon monoxide were studied experimentally using guided-ion-beam mass spectrometry. Anionic clusters with a stoichiometry containing one more oxygen atom than nickel atom (NiO2-, Ni2O3-, Ni3O4- and Ni4O5-) were found to exhibit dominant products resulting from the transfer of a single oxygen atom to CO, suggesting the formation of CO2. Of these four species, Ni2O3- and Ni4O5- were observed to be the most reactive having oxygen transfer products accounting for approximately 5% and 10% of the total ion intensity at a maximum pressure of 15 mTorr of CO. Our findings, therefore, indicate that anionic nickel oxide clusters containing an even number of nickel atoms and an odd number of oxygen atoms are more reactive than those with an odd number of nickel atoms and an even number of oxygen atoms. The majority of cationic nickel oxides, in contrast to anionic species, reacted preferentially through the adsorption of CO onto the cluster accompanied by the loss of either molecular O2 or nickel oxide units. The adsorption of CO onto positively charged nickel oxides, therefore, is exothermic enough to break apart the gas-phase clusters. Collision induced dissociation experiments, employing inert xenon gas, were also conducted to gain insight into the structural properties of nickel oxide clusters. The fragmentation products were found to vary considerably with size and stoichiometry as well as ionic charge state. In general, cationic clusters favored the collisional loss of molecular O2 while anionic clusters fragmented through the loss of both atomic oxygen and nickel oxide units. Our results provide insight into the effect of ionic charge state on the structure of nickel oxide clusters. Furthermore, we establish how the size and stoichiometry of nickel oxide clusters influences their ability to oxidize CO, an important reaction for environmental pollution abatement.

Improving hydrogen storage in Ni-doped carbon nanospheres

Energy Technology Data Exchange (ETDEWEB)

Zubizarreta, L.; Menendez, J.A.; Pis, J.J.; Arenillas, A. [Instituto Nacional del Carbon, CSIC, Apartado 73, 33080 Oviedo (Spain)

2009-04-15

The effect of nickel distribution and content in Ni-doped carbon nanospheres on hydrogen storage capacity under conditions of moderate temperature and pressure was studied. It was found that the nickel distribution, obtained by using different doping techniques and conditions, has a noticeable influence on hydrogen storage capacity. The samples with the most homogeneous nickel distribution, obtained by pre-oxidising the carbon nanospheres, displayed the highest storage capacity. In addition, storage capacity is influenced by the amount of nickel. It was found a higher storage capacity in samples containing 5 wt.% of Ni. This is due to the greater interactions between the nickel and the support that produce a higher activation of the solid through a spillover effect. (author)

Controllable synthesis of hierarchical nickel cobalt sulfide with enhanced electrochemical activity

Science.gov (United States)

Tie, Jinjin; Han, Jiaxi; Diao, Guiqiang; Liu, Jiwen; Xie, Zhuopeng; Cheng, Gao; Sun, Ming; Yu, Lin

2018-03-01

The composition of nickel cobalt sulfide has great influence on its electrochemical performance. Herein, the nickel cobalt sulfide with different composition and mixed phase were synthesized by one-step solvothermal method through changing the molar ratio of Ni to Co in the reaction system. The electrochemical measurements showed that the nickel cobalt sulfide with a theoretical molar ratio of Ni/Co to be 1.5:1.5 (NCS-2) demonstrates the superior pseudocapacitive performance with a high specific capacitance (6.47 F cm-2 at 10 mA cm-2) and a favorable Coulombic efficiency (∼99%). Whereas, when applied as the catalyst for hydrogen evolution reaction in 1 M KOH aqueous electrolyte, the nickel cobalt sulfide with a theoretical molar ratio of Ni/Co is 1:2 (NCS-1) displays better catalytic activity, and it requires a relatively lower overpotential of 282 mV to deliver the current density of 10 mA cm-2.

Preparation and characterization of alumina supported nickel-oxalate catalyst for the hydrodeoxygenation of oleic acid into normal and iso-octadecane biofuel

International Nuclear Information System (INIS)

Ayodele, O.B.; Togunwa, Olayinka S.; Abbas, Hazzim F.; Daud, Wan Mohd Ashri Wan

2014-01-01

Highlights: • Preparation of nickel oxalate complex as catalyst precursor. • Incorporation of nickel oxalate complex into alumina support. • Characterization of the alumina supported nickel oxalate catalyst. • Hydrodeoxygenation of oleic acid with nickel oxalate catalyst. • Nickel oxalate catalyst reusability studies. - Abstract: In this study, nickel II oxalate complex (NiOx) was prepared by functionalization of nickel with oxalic acid (OxA) and incorporated into Al 2 O 3 to synthesize alumina supported nickel oxalate (NiOx/Al 2 O 3 ) catalyst for the hydrodeoxygenation (HDO) of oleic acid (OA) into biofuel. The synthesized NiOx/Al 2 O 3 was characterized and the X-ray fluorescence and elemental dispersive X-ray results showed that NiOx was successfully incorporated into the structure of Al 2 O 3 . The X-ray diffraction and Raman spectroscopy results confirmed that highly dispersed Ni species are present in the NiOx/Al 2 O 3 due to the functionalization with OxA. The catalytic activity of the NiOx/Al 2 O 3 on the HDO of OA produced a mixture of 21% iso-C18 and 72% n-C18 at a 360 °C, 20 bar, 30 mg NiOx/Al 2 O 3 loading pressure and gas flow rate of 100 mL/min. The presence of i-C 18 was ascribed to the OxA functionalization which increased the acidity of NiOx/Al 2 O 3 . The NiOx/Al 2 O 3 reusability study showed consistent HDO ability after 5 runs. These results are promising for further research into biofuel production for commercialization

Highly Dispersed Nickel-Containing Mesoporous Silica with Superior Stability in Carbon Dioxide Reforming of Methane: The Effect of Anchoring

Directory of Open Access Journals (Sweden)

Wenjia Cai

2014-03-01

Full Text Available A series of nickel-containing mesoporous silica samples (Ni-SiO2 with different nickel content (3.1%–13.2% were synthesized by the evaporation-induced self-assembly method. Their catalytic activity was tested in carbon dioxide reforming of methane. The characterization results revealed that the catalysts, e.g., 6.7%Ni-SiO2, with highly dispersed small nickel particles, exhibited excellent catalytic activity and long-term stability. The metallic nickel particle size was significantly affected by the metal anchoring effect between metallic nickel particles and unreduced nickel ions in the silica matrix. A strong anchoring effect was suggested to account for the remaining of small Ni particle size and the improved catalytic performance.

HDO of Methyl Palmitate over Silica-Supported Ni Phosphides: Insight into Ni/P Effect

Directory of Open Access Journals (Sweden)

Irina V. Deliy

2017-10-01

Full Text Available Two sets of silica-supported nickel phosphide catalysts with a nickel content of about 2.5 and 10 wt % and Ni/P molar ratio 2/1, 1/1 and 1/2 in each set, were prepared by way of a temperature-programmed reduction method using (Ni(CH3COO2 and ((NH42HPO4 as a precursor. The NixPy/SiO2 catalysts were characterized using chemical analysis N2 physisorption, XRD, TEM, 31P MAS NMR. Methyl palmitate hydrodeoxygenation (HDO was performed in a trickle-bed reactor at 3 MPa and 290 °C with LHSV ranging from 0.3 to 16 h−1. The Ni/P ratio was found to affect the nickel phosphide phase composition, POx groups content and catalytic properties in methyl palmitate HDO with the TOF increased along with a decline of Ni/P ratio and a growth of POx groups’ content. Taking into account the possible routes of methyl palmitate conversion (metal-catalyzed hydrogenolysis or acid-catalyzed hydrolysis, we proposed that the enhancement of acid POx groups’ content with the Ni/P ratio decrease provides an enhancement of the rate of methyl palmitate conversion through the acceleration of acid-catalyzed hydrolysis.

Investigation of effect of Ag(1), Cd(2) and Zn(2) on chemical nickel plating

International Nuclear Information System (INIS)

Lunyatskas, A.M.; Tarozajte, R.K.; Gyanutene, I.K.; Lyaukonis, Yu.Yu.

1978-01-01

Investigated is the effect of Ag(1), Cd(2) and Zn(2) on chemical nickel plating using hypophosphite aimed to get corresponding alloys from alkali solutions. The H 2 formed volume and potential of coating have been measured while nickel plating. It is possible to have plating of Ni-P-Ag, Ni-P-Zn, Ni-P-Cd, Ni-P-Zn-Cd content coatings in alkali solutions using hypophosphite Ni-P-Zh and Ni-P-Zn-Cd coatings have corrosion resistance and unporousness. Cd and Zn inclusion in Ni-P coating is supposed to have both chemical and electrochemical origin

A solid paraffin-based carbon paste electrode modified with 2-aminothiazole organofunctionalized silica for differential pulse adsorptive stripping analysis of nickel in ethanol fuel

International Nuclear Information System (INIS)

Takeuchi, Regina M.; Santos, Andre L.; Padilha, Pedro M.; Stradiotto, Nelson R.

2007-01-01

A solid paraffin-based carbon paste electrode modified with 2-aminothiazole organofunctionalized silica (SiAt-SPCPE) was applied to Ni 2+ determination in commercial ethanol fuel samples. The proposed method comprised four steps: (1) Ni 2+ preconcentration at open circuit potential directly in the ethanol fuel sample, (2) transference of the electrode to an electrochemical cell containing DMG, (3) differential pulse voltammogram registering and (4) surface regeneration by polishing the electrode. The proposed method combines the high Ni 2+ adsorption capacity presented by 2-aminothiazole organofunctionalized silica with the electrochemical properties of the Ni(DMG) 2 complex, whose electrochemical reduction provides the analytical signal. All experimental parameters involved in the proposed method were optimized. Using a preconcentration time of 20 min, it was obtained a linear range from 7.5 x 10 -9 to 1.0 x 10 -6 mol L -1 with detection limit of 2.0 x 10 -9 mol L -1 . Recovery values between 96.5 and 102.4% were obtained for commercial samples spiked with 1.0 μmol L -1 Ni 2+ and the developed electrode was totally stable in ethanolic solutions. The contents of Ni 2+ found in the commercial samples using the proposed method were compared to those obtained by graphite furnace atomic absorption spectroscopy by using the F- and t-test. Neither the F- nor t-values exceeded the critical values at 95% confidence level, confirming that there are not statistical differences between the results obtained by both methods. These results indicate that the developed electrode can be successfully employed to reliable Ni 2+ determination in commercial ethanol fuel samples without any sample pretreatment or dilution step

Effect of different nickel precursors on capacitive behavior of electrodeposited NiO thin films

Energy Technology Data Exchange (ETDEWEB)

Kore, R. M.; Ghadge, T. S.; Ambare, R. C.; Lokhande, B. J., E-mail: bjlokhande@yahoo.com [School of Physical Sciences, Solapur University, Solapur-413 255, M.S. (India)

2016-04-13

In the present study, the effect of nickel precursors containing different anions like nitrate, chloride and sulphate on the morphology and pseudocapacitance behavior of NiO is investigated. The NiO samples were prepared by using a potentiondynamic electrodeposition technique in the three electrode cell. Cyclic voltammetry technique was exploited for potentiodynamic deposition of the films. The obtained samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), etc. The XRD reveals the cubic crystal structure for all samples. The SEM micrograph shows nanoflakelike, up grown nanoflakes and honeycomb like nanostructured morphologies for nitrate, chloride and sulphate precursors respectively. The capacitive behavior of these samples was recorded using cyclic voltammetry (CV), charge-discharge and electrochemical impedance spectroscopy (EIS) in 1 M KOH electrolyte. The specific capacitance values of NiO samples obtained using CV for nitrate, chloride and sulphate precursors were 136, 214 and 893 Fg{sup −1} respectively, at the scan rate of 5 mVs{sup −1}. The charge discharge study shows high specific energy for the sample obtained from sulphate (23.98 Whkg{sup −1}) as compared to chloride (9.67 Whkg{sup −1}) and nitrate (4.9 Whkg{sup −1}), whereas samples of cholride (13.9 kWkg{sup −1} and nitrate (10.5 kWkg{sup −1}) shows comparatively more specific power than samples obtained from sulphate (7.6 kWkg{sup −1}). The equivalent series resistance of NiO samples observed from EIS study are 1.34, 1.29 and 1.27 Ω respectively for nitrate, chloride and sulphate precursors. These results emphasizes that the samples obtained from sulphate precursors provides very low impedance through honeycomb like nanostructured morphology which supports good capacitive behavior of NiO.

Potassium/calcium/nickel oxide catalysts for the oxidative coupling of methane

NARCIS (Netherlands)

Dooley, K.; Dooley, Kerry M.; Ross, J.R.H.; Ross, Julian R.H.

1992-01-01

A series of potassium/calcium/nickel oxides were tested for the oxidative coupling of methane (OCM) at 843–943 K and water addition to the feed at 0–66 mol-%. The K/Ni ratios varied from 0.0–0.6 and Ca/Ni from 0.0–11; catalysts with no nickel were also tested. At least 10% water in the feed and

Synthesis of Nickel (Ni) Doped HKUST-1 Using Solvotermal Method with Addition of Acetic Acid as Modulator

OpenAIRE

Safii, Farhan Fikri; Ediati, Ratna

2015-01-01

Hong Kong University of Science and Technology-1 (HKUST-1) is metal organic framework (MOF) that composed from ligand BTC (1,3,5-benzene tricarboxylic) and copper ions. The method used in this study is solvotermal with variations nickel ion doping and additions acetic acid as modulator. The purpose of this study is to increase the hydrogen storage capacity. The results obtained were characterized by XRD showed that the HKUST-1 and Ni-HKUST-1 has formed, showed by peaks at 2 theta = 6.7, 9.5, ...

Optical and structural characterization of nickel oxide-based thin films obtained by chemical bath deposition

International Nuclear Information System (INIS)

Vidales-Hurtado, M.A.; Mendoza-Galvan, A.

2008-01-01

Nickel oxide-based thin films were obtained using the chemical bath deposition method on glass and silicon substrates. The precursor solution used was a mixture of nickel nitrate, urea, and deionized water. Molar concentration of nickel (0.3-1.0 M), deposition time, and immersing cycles were considered as deposition variables. Infrared spectroscopy and X-ray diffraction data reveal that all as-deposited films correspond to the transparent turbostratic phase α(II)-Ni(OH) 2 . However, the rate of deposition depends on nickel content in the solution. After annealing in air at temperatures above of 300 deg. C, the films are transformed to the NiO phase and show a grey/black color. In these films, scanning electron microscopy images show aggregates of thin stacked sheets on their surface, such aggregates can be easily removed leaving only a thin NiO layer of about 30 nm adhered firmly to the substrate, regardless of nickel concentration in the solution and deposition time. In order to obtain thicker NiO films with good optical properties a procedure is developed performing several immersing-annealing cycles

A simple and efficient method of nickel electrodeposition for the cyclotron production of 64Cu

International Nuclear Information System (INIS)

Manrique-Arias, Juan C.; Avila-Rodriguez, Miguel A.

2014-01-01

Nickel targets for the cyclotron production of 64 Cu were prepared by electrodeposition on a gold backing from nickel chloride solutions using boric acid as buffer. Parameters studied were nickel chloride and boric acid concentration, temperature and current density. All plating conditions studied were successful obtaining efficiencies of approximately 90% in 2–3 h, reaching almost quantitative plating (>97%) in 10–20 h depending on the current density. All plated targets withstood proton irradiations up to 40 µA for 2 h. Recovered nickel was successfully recycled and reused with an overall efficiency >95%. - Highlights: • Simple and efficient method of Ni electrodeposition from NiCl 2 solutions. • Represents an improvement over current methods for the preparation of Ni targets. • All plated targets underwent irradiation and withstood currents up to 40 µA for 2 h. • Nickel target material was recycled and reused with an overall efficiency >95%. • Specific activity of 64 Cu was similar than that obtained with older methods of Ni plating

Electrochemical investigations and characterization of a metal hydride alloy (MmNi3.6Al0.4Co0.7Mn0.3) for nickel metal hydride batteries

International Nuclear Information System (INIS)

Begum, S. Nathira; Muralidharan, V.S.; Basha, C. Ahmed

2009-01-01

The use of new hydrogen absorbing alloys as negative electrodes in rechargeable batteries has allowed the consideration of nickel/metal hydride (Ni/MH) batteries to replace the conventional nickel cadmium alkaline or lead acid batteries. In this study the performance of trisubstituted hydrogen storage alloy (MmNi 3.6 Al 0.4 Co 0.7 Mn 0.3 ) electrodes used as anodes in Ni/MH secondary batteries were evaluated. MH electrodes were prepared and the electrochemical utilization of the active material was investigated. Cyclic voltammetric technique was used to analyze the beneficial effect of the alloy by various substitutions. The electrochemical impedance spectroscopic measurements of the Ni/MH battery were made at various states of depth of discharge. The effect of temperature on specific capacity is studied and specific capacity as a function of discharge current density was also studied and the results were analyzed. The alloy metal hydride electrode was subjected to charge/discharge cycle for more than 200 cycles. The discharge capacities of the alloy remains at 250 mAh/g with a nominal fading in capacity (to the extent of ∼20 mAh/g) on prolonged cycling

Toxicology and metabolism of nickel compounds. Progress report, December 1, 1978-November 30, 1979. [Hamsters and rats

Energy Technology Data Exchange (ETDEWEB)

Sunderman, F.W. Jr.

1979-08-15

The toxicology and metabolism of nickel compounds were investigated in rats and hamsters. The new knowledge includes; demonstration that nickel carbonyl is teratogenic for hamsters; elucidation of physiological factors which influence ..cap alpha..Ni/sub 3/S/sub 2/-induced erythrocytosis in rats; development of a sensitive assay for heme oxygenase activity in renal microsomes for use in studies of renal effects of nickel compounds; demonstration that administration of Ni(CO)/sub 4/ to rats inhibits incorporation of /sup 3/H-thymidine into DNA during hepatic regeneration; demonstration that clones of Syrian hamster fetal cells which have been transformed by in vitro exposure to ..cap alpha..Ni/sub 3/S/sub 2/ consistently cause sarcomas following sc injection into nude mice; demonstration that nickel carbonyl-cyclopentadiene dimer induces rhabdomyosarcomas following im injection in rats; observation of differences in carcinogenic activities of several insoluble nickel compounds; discovery that intraocular injection of ..cap alpha..Ni/sub 3/S/sub 2/ induces amelanotic melanomas in rats; and refinement of analytical methods for nickel in biological materials.

Electrical and magnetic properties of electrodeposited nickel incorporated diamond-like carbon thin films

Energy Technology Data Exchange (ETDEWEB)

Pandey, B., E-mail: pandey.beauty@yahoo.com [Department of Applied Physics, Indian School of Mines, Dhanbad 826004 (India); Das, D. [UGC-DAE CSR, Sector III/LB-8, Bidhan Nagar, Kolkata 700098 (India); Kar, A.K. [Department of Applied Physics, Indian School of Mines, Dhanbad 826004 (India)

2015-05-15

Highlights: • Electrical and magnetic properties of DLC and Ni-DLC thin films are studied. • The ohmicity and conductivity of DLC films rise with nickel addition. • The ohmicity of Ni-DLC is enhanced with increase in dilution of electrolyte. • Dielectric loss is high for Ni-DLC and decreases with frequency till 100 kHz. • (m–H) and (m–T) curves of Ni-DLC indicate superparamagnetic behavior. - Abstract: Nanocomposite diamond-like carbon (DLC) thin films have been synthesized by incorporating nickel (Ni) nanoparticles in DLC matrix with varying concentration of nickel. DLC and Ni-DLC thin films have been deposited on ITO coated glass substrates employing low voltage electrodeposition method. Electrical properties of the samples were studied by measuring current–voltage characteristics and dielectric properties. The current approaches toward an ohmic behavior with metal addition. This tendency of increasing ohmicity is enhanced with increase in dilution of the electrolyte. The conductivity increases with Ni addition and interestingly it continues to increase with dilution of Ni concentration in the electrolyte in the range of our study. Magnetic properties for DLC and Ni-DLC thin film samples were examined by electron paramagnetic resonance (EPR) measurements and Super Conducting Quantum Interference Device (SQUID) measurements. g-Value for DLC is 2.074, whereas it decreases to 2.055 with Ni addition in the electrolyte. This decrement arises from the increased sp{sup 2} content in DLC matrix. The magnetic moment vs. magnetic field (m–H) curves of Ni-DLC indicate superparamagnetic behavior which may be due to ferromagnetic contribution from the incorporated nickel nanoparticles in the DLC matrix. The ZFC curve of Ni-DLC after the blocking temperature shows a combined contribution of ferromagnetic, superparamagnetic and paramagnetic nature of the materials persisting up to 300 K.

Preparation and properties of a novel macro porous Ni2+-imprinted chitosan foam adsorbents for adsorption of nickel ions from aqueous solution.

Science.gov (United States)

Guo, Na; Su, Shi-Jun; Liao, Bing; Ding, Sang-Lan; Sun, Wei-Yi

2017-06-01

In this study, novel macro porous Ni 2+ -imprinted chitosan foam adsorbents (F-IIP) were prepared using sodium bicarbonate and glycerine to obtain a porogen for adsorbing nickel ions from aqueous solutions. The use of the ion-imprinting technique for adsorbents preparation improved the nickel ion selectivity and adsorption capacity. We characterised the imprinted porous foam adsorbents in terms of the effects of the initial pH value, initial metal ion concentration, and contact time on the adsorption of nickel ions. The adsorption process was described best by Langmuir monolayer adsorption models, and the maximum adsorption capacity calculated from the Langmuir equation was 69.93mgg -1 . The kinetic data could be fitted to a pseudo-second-order equation. Our analysis of selective adsorption demonstrated the excellent preference of the F-IIP foams for nickel ions compared with other coexisting metal ions. Furthermore, tests over five cycle runs suggested that the F-IIP foam adsorbents had good durability and efficiency. Copyright © 2017 Elsevier Ltd. All rights reserved.

Nickel/carbon core/shell nanotubes: Lanthanum nickel alloy catalyzed synthesis, characterization and studies on their ferromagnetic and lithium-ion storage properties

International Nuclear Information System (INIS)

Anthuvan Rajesh, John; Pandurangan, Arumugam; Senthil, Chenrayan; Sasidharan, Manickam

2014-01-01

Highlights: • Ni/CNTs core/shell structure was synthesized using LaNi 5 alloy catalyst by CVD. • The magnetic and lithium-ion storage properties of Ni/CNTs structure were studied. • The specific Ni/CNTs structure shows strong ferromagnetic property with large coercivity value of 446.42 Oe. • Ni/CNTs structure shows enhanced electrochemical performance in terms of stable capacity and better rate capability. - Abstract: A method was developed to synthesize ferromagnetic nickel core/carbon shell nanotubes (Ni/CNTs) by chemical vapor deposition using Pauli paramagnetic lanthanum nickel (LaNi 5 ) alloy both as a catalyst and as a source for the Ni-core. The Ni-core was obtained through oxidative dissociation followed by hydrogen reduction during the catalytic growth of the CNTs. Transmission electron microscopy (TEM), selected area electron diffraction (SAED) and X-ray diffraction (XRD) analyses reveal that the Ni-core exists as a face centered cubic single crystal. The magnetic hysteresis loop of Ni/CNTs particle shows increased coercivity (446.42 Oe) than bulk Ni at room temperature. Furthermore, the Ni/CNTs core/shell particles were investigated as anode materials in lithium-ion batteries. The Ni/CNTs electrode delivered a high discharge capacity of 309 mA h g −1 at 0.2 C, and a stable cycle-life, which is attributed to high structural stability of Ni/CNTs electrode during electrochemical lithium-ion insertion and de-insertion redox reactions

Iron and silicon effect on the phase composition of nickel-beryllium bronzes

International Nuclear Information System (INIS)

Zakharov, A.M.; Zakharov, M.V.; Ajvaz'yan, N.G.

1977-01-01

In order to specify phase composition and strengthening heat treatment conditions for nickel beryllium bronzes that are promising electrode materials for welding of high strength steels and nickel-base superalloys, the primary section of the quinternary Cu-Ni-Be-Fe-S system was studied at constant nickel and beryllium concentration and varying silicon and iron concentration (max. 4% of every element). The study was made using the metallographic and x-ray phase techniques, determination of alloy solidus temperature, and exessphase microhardness testing. Silicon additions are shown to decrease abruptly and those of iron, in contrast, somewhat to raise the solidus temperature of ternary Cu + 2% Ni + 0.3% Be alloy. When added concurrently, iron compensates for the damaging silicon effect on the solidus temperature of Cu-Ni-Be alloys. The excess phases formed can be used as strengthening agents of Cu-Ni-Be-Si-Fe alloys during quenching and subsequent aging

The influence of nickel content on microstructures of Fe-Cr-Ni austenitic alloys irradiated with nickel ions

International Nuclear Information System (INIS)

Muroga, T.; Yoshida, N.; Garner, F.A.

1990-11-01

The objectives of this effort is to identify the mechanisms involved in the radiation-induced evolution of microstructure in materials intended for fusion applications. The results of this study are useful in interpreting the results of several other ongoing experiments involving either spectral or isotopic tailoring to study the effects of helium on microstructure evolution. Ion-irradiated Fe-15Cr-XNi (X = 20, 35, 45, 60, 75) ternary alloys and a 15Cr-85Ni binary alloy were examined after bombardment at 675 degree C and compared to earlier observations made on these same alloys after irradiation in EBR-II at 510 or 538 degree C. The response of the ion-irradiated microstructures to nickel content appears to be very consistent with that of neutron irradiation even though there are four orders of magnitude difference in displacement rate and over 200 degree C difference in temperature. It appears that the transition to higher rates of swelling during both types of irradiation is related to the operation of some mechanisms that is not directly associated with void nucleation. 6 refs., 8 figs

Graph theory and binary alloys passivated by nickel

International Nuclear Information System (INIS)

McCafferty, E.

2005-01-01

The passivity of a nickel binary alloy is considered in terms of a network of -Ni-O-Ni- bridges in the oxide film, where Ni is the component of the binary alloy which produces passivity. The structure of the oxide is represented by a mathematical graph, and graph theory is used to calculate the connectivity of the oxide, given by the product of the number of edges in the graph and the Randic index. A stochastic calculation is employed to insert ions of the second metal into the oxide film so as to disrupt the connectivity of the -Ni-O-Ni- network. This disruption occurs at a critical ionic concentration of the oxide film. Mathematical relationships are developed for the introduction of a general ion B +n into the oxide film, and critical ionic compositions are calculated for oxide films on the nickel binary alloys. The notation B refers to any metal B which produces B +n ions in the oxide film, where +n is the oxidation number of the ion. The results of this analysis for Fe-Ni and Cu-Ni binary alloys are in good agreement with experimental results

The relationship between the addition method of the Ni-activator and the sinterability for the Ni-doped W-powder compact

International Nuclear Information System (INIS)

Moon, I.H.; Kim, J.S.

1984-01-01

The relationship between the nickel size added to tungsten powder and the sinterability was investigated for the Ni-doped W-powder compact. The Ni-added W-powder compact with various particle size ratios of W to Ni were prepared by mechanical mixing as well as by salt solution and reduction method. In the latter method the size of reduced Ni-particle could be controlled by drying rate of salt solution. The smaller the size of nickel particles added to W was, the activatedly sintered W-powder compact has shown higher sinterability in the initial stage of sintering. The dependence of sinterability on the size of Ni-activator could be partly explained by some physical characteristics of Ni-activator at sintering temperature. (Auth.)

Ultrathin mesoporous NiCo{sub 2}O{sub 4} nanosheets supported on Ni foam as advanced electrodes for supercapacitors

Energy Technology Data Exchange (ETDEWEB)

Yuan, Changzhou [Anhui Key Laboratory of Metal Materials and Processing, School of Materials Science and Engineering, Anhui University of Technology, Maanshan, 243002 (China); School of Chemical and Biomedical Engineering, Nanyang Technological University, 70 Nanyang Drive (Singapore); Li, Jiaoyang; Hou, Linrui [Anhui Key Laboratory of Metal Materials and Processing, School of Materials Science and Engineering, Anhui University of Technology, Maanshan, 243002 (China); Zhang, Xiaogang; Shen, Laifa [College of Material Science and Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing, 210016 (China); Lou, Xiong Wen [School of Chemical and Biomedical Engineering, Nanyang Technological University, 70 Nanyang Drive (Singapore)

2012-11-07

A facile two-step method is developed for large-scale growth of ultrathin mesoporous nickel cobaltite (NiCo{sub 2}O{sub 4}) nanosheets on conductive nickel foam with robust adhesion as a high-performance electrode for electrochemical capacitors. The synthesis involves the co-electrodeposition of a bimetallic (Ni, Co) hydroxide precursor on a Ni foam support and subsequent thermal transformation to spinel mesoporous NiCo{sub 2}O{sub 4}. The as-prepared ultrathin NiCo{sub 2}O{sub 4} nanosheets with the thickness of a few nanometers possess many interparticle mesopores with a size range from 2 to 5 nm. The nickel foam supported ultrathin mesoporous NiCo{sub 2}O{sub 4} nanosheets promise fast electron and ion transport, large electroactive surface area, and excellent structural stability. As a result, superior pseudocapacitive performance is achieved with an ultrahigh specific capacitance of 1450 F g{sup -1}, even at a very high current density of 20 A g{sup -1}, and excellent cycling performance at high rates, suggesting its promising application as an efficient electrode for electrochemical capacitors. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Mechanochemical Synthesis of Nanostructured MgXNi1-XO Compound by Mg-NiO Mixture

Directory of Open Access Journals (Sweden)

Nader Setoudeh

2017-06-01

Full Text Available Synthesis of magnesium nickel oxide phase such as MgxNi1-xO solid solutions has been studied in this research article using mechnochmical reaction between magnesium and nickel oxide. Mixtures of magnesium powder and nickel oxide (Mg+NiO with stoichiometric compositions were milled for different times in a planetary ball mill. Reduction reaction of nickel oxide by magnesium via a mechanically induced self-sustaining reaction (MSR was confirmed in the XRD measurements of the as-milled samples. Formation of nanostructured magnesium nickel oxide phases (such as Mg0.4Ni0.6O or MgNiO2 was observed after isothermal heating of the 30 minutes milled samples at 1000°C where nickel phase seems to disappear in XRD patterns. The traces of phases such as Mg0.4Ni0.6O or MgNiO2 were also observed in the as-milled mixtures. Therefore, the XRD results of the as-milled samples suggested that the formation of magnesium nickel oxide phases could be possible even after prolonged milling. The XRD and SEM results of both as-milled and isothermally heated samples indicated that the crystallite size and particle size of the final products reached to nanoscale after milling. Morphological and compositional evolution of the samples after heat treatment was monitored through SEM imaging and elemental analyses. The results confirmed that the composition of final product is close to Mg0.4Ni0.6O compound.

Engineered nickel oxide nanoparticle causes substantial physicochemical perturbation in plants

Science.gov (United States)

Manna, Indrani; Bandyopadhyay, Maumita

2017-11-01

Concentration of engineered NiO-NP in nature is on the rise, owing to large scale industrial uses and human interventions, which have accreted the scope of exposure especially at the primary trophic levels of the ecosystem. Nickel content in air, drinking water and soil is already above permissible limits in most parts of the developed world. Though nickel oxide is an essential micronutrient in the animal system, it has already been graded as a human carcinogen by WHO, and numerous studies have established the toxic nature of nickel in higher dosage in the animal system. Though studies depicting toxicity and bioaccumulation of nickel in plants is documented, the interaction of nickel oxide nanoparticle with plants is not fully a well-studied, well elucidated topic. What is known is that, exposure to nickel oxide nanoparticle, arouses stress response and leads to cytotoxicity and growth retardation in a handful of plants, a defined work on the intricate physicochemical cellular responses and genotoxic challenges has been so far absent. We have tried to fill in such gaps with this study. We planned the work around pertinent hypotheses like: whether NiO-NP cause cytotoxicity in a model plant system (Allium cepa L.)?If so, does internalization of nickel ion (the potent toxic) take place in the tissue? Does internalized NiO-NP create furore in the antioxidant enzyme system of the plant leading to cytotoxicity? In that case, whether the ENP causes genotoxicity and leads to pycknosis of the cell. The study has been designed to assess the change in biochemical profile and genotoxicity potential of NiO-NP at a wide range of concentrations using root tips of Allium cepa L., the model system for study of cytotoxicity and genotoxicity, and four of its closest relatives, Allium sativum L., Allium schoenoprasum L., Allium porrum L., Allium fistulosum L., chosen for their immense economic importance. Growing root tips were treated with seven different concentrations of Ni

Microstructural development in NiAl/Ni-Si-B/Ni transient liquid phase bonds

International Nuclear Information System (INIS)

Gale, W.F.; Orel, S.V.

1996-01-01

A transmission electron microscopy (TEM) based investigation of microstructural development during transient liquid phase bonding of near-stoichiometric NiAl to commercial purity nickel is presented in this article. The work described employed Ni-4.5 wt pct Si-3.2 wt pct B (BNi-3) melt-spun interlayers. The precipitation of both Ni-Al based phases and borides within the joint and adjacent substrate regions is discussed. The article considers martensite formation (within the NiAl substrate) and the precipitation of L1 2 type phases (both within the joint and at the interface with the NiAl substrate). The relative roles of the two substrate materials (NiAl and Ni) in the isothermal resolidification process are identified. The preferential formation of Ni 3 B boride phases in the Ni substrate near the original location of the Ni substrate-joint interface is discussed and contrasted with the absence of similar events in the NiAl substrate

Research Advances on Pathways of Nickel-Induced Apoptosis

Science.gov (United States)

Guo, Hongrui; Chen, Lian; Cui, Hengmin; Peng, Xi; Fang, Jing; Zuo, Zhicai; Deng, Junliang; Wang, Xun; Wu, Bangyuan

2015-01-01

High concentrations of nickel (Ni) are harmful to humans and animals. Ni targets a number of organs and produces multiple toxic effects. Apoptosis is important in Ni-induced toxicity of the kidneys, liver, nerves, and immune system. Apoptotic pathways mediated by reactive oxygen species (ROS), mitochondria, endoplasmic reticulum (ER), Fas, and c-Myc participate in Ni-induced cell apoptosis. However, the exact mechanism of apoptosis caused by Ni is still unclear. Understanding the mechanism of Ni-induced apoptosis may help in designing measures to prevent Ni toxicity. PMID:26703593

Synthesis of Nickel-Encapsulated Carbon Nanocapsules and Cup-Stacked-Type Carbon Nanotubes via Nickel-Doped Fullerene Nanowhiskers

Directory of Open Access Journals (Sweden)

Tokushi Kizuka

2012-01-01

Full Text Available Nickel- (Ni doped C60 nanowhiskers (NWs were synthesized by a liquid-liquid interfacial precipitation method using a C60-saturated toluene solution and isopropanol with Ni nitrate hexahydrate Ni(NO32·6H2O. By varying the heating temperature of Ni-doped C60 NWs, two types of one-dimensional carbon nanostructures were produced. By heating the NWs at 973 and 1173 K, carbon nanocapsules (CNCs that encapsulated Ni nanoparticles were produced. The Ni-encapsulated CNCs joined one dimensionally to form chain structures. Upon heating the NWs to 1373 K, cup-stacked-type carbon nanotubes were synthesized.

Nitrogen atom transfer mediated by a new PN3P-pincer nickel core via a putative nitrido nickel intermediate

KAUST Repository

Yao, Changguang

2018-02-13

A 2nd generation PN3P-pincer azido nickel complex (PN3P)Ni(N3) reacts with isocyanides to afford monosubstituted carbodiimides under irradiation, presumably via a transient nitrido intermediate. The resulting species can further generate unsymmetrical carboddimides and the PN3P nickel halide complex, accomplishing a synthetic cycle for a complete nitrogen atom transfer reaction.

Nitrogen atom transfer mediated by a new PN3P-pincer nickel core via a putative nitrido nickel intermediate

KAUST Repository

Yao, Changguang; Wang, Xiufang; Huang, Kuo-Wei

2018-01-01

A 2nd generation PN3P-pincer azido nickel complex (PN3P)Ni(N3) reacts with isocyanides to afford monosubstituted carbodiimides under irradiation, presumably via a transient nitrido intermediate. The resulting species can further generate unsymmetrical carboddimides and the PN3P nickel halide complex, accomplishing a synthetic cycle for a complete nitrogen atom transfer reaction.

Stable cyclic performance of nickel oxide–carbon composite anode for lithium-ion batteries

International Nuclear Information System (INIS)

Susantyoko, Rahmat Agung; Wang, Xinghui; Fan, Yu; Xiao, Qizhen; Fitzgerald, Eugene; Pey, Kin Leong; Zhang, Qing

2014-01-01

Nickel oxide (NiO) directly grown on nickel foam is regarded as a promising lithium ion battery anode material which shows good cyclic and rate performances with a theoretical specific capacity of 718 mA h g −1 . In this study, we demonstrated a carbon-incorporated NiO anode (NiO–C) with a capacity per unit area of 2.11 mA h cm −2 and 1.76 mA h cm −2 at 0.2 C and 0.5 C rates, respectively, fabricated by thermal oxidation of carbon coated nickel foam. The specific capacity of our NiO–C composite samples at 0.5 C rate is found to be typically 389.16 mA h g −1 , with a stable cyclic performance up to more than 100 cycles. This remarkable performance is apparently superior to the control samples of pure NiO samples. The improved performance is contributed to carbon incorporation which serves as a fluent channel for electrons and a flexible network preventing NiO nanostructures from structural deformation during charge and discharge processes. The advantage of using our approach is the easy preparation of the NiO–C composite using a simple two-step process: chemical vapor deposition of ethanol and annealing in air. - Highlights: • We demonstrated a directly grown NiO–C anode on nickel foam substrate. • NiO–C anode was made using simple processes: CVD of ethanol and annealing in air. • The NiO–C anode has a stable cycle life up to 102 cycles. • It has an acceptable areal capacity (1.76 mA h cm −2 at 0.5 C rate) for practical use. • Carbon provides electrons path and buffering matrix preventing NiO pulverization