Evaluation of Shielding Performance for Newly Developed Composite Materials

Science.gov (United States)

Evans, Beren Richard

This work details an investigation into the contributing factors behind the success of newly developed composite neutron shield materials. Monte Carlo simulation methods were utilized to assess the neutron shielding capabilities and secondary radiation production characteristics of aluminum boron carbide, tungsten boron carbide, bismuth borosilicate glass, and Metathene within various neutron energy spectra. Shielding performance and secondary radiation data suggested that tungsten boron carbide was the most effective composite material. An analysis of the macroscopic cross-section contributions from constituent materials and interaction mechanisms was then performed in an attempt to determine the reasons for tungsten boron carbide's success over the other investigated materials. This analysis determined that there was a positive correlation between a non-elastic interaction contribution towards a material's total cross-section and shielding performance within the thermal and epi-thermal energy regimes. This finding was assumed to be a result of the boron-10 absorption reaction. The analysis also determined that within the faster energy regions, materials featuring higher non-elastic interaction contributions were comparable to those exhibiting primarily elastic scattering via low Z elements. This allowed for the conclusion that composite shield success within higher energy neutron spectra does not necessitate the use elastic scattering via low Z elements. These findings suggest that the inclusion of materials featuring high thermal absorption properties is more critical to composite neutron shield performance than the presence of constituent materials more inclined to maximize elastic scattering energy loss.

Verification of gamma knife based fractionated radiosurgery with newly developed head-thorax phantom

International Nuclear Information System (INIS)

Bisht, Raj Kishor; Kale, Shashank Sharad; Natanasabapathi, Gopishankar; Singh, Manmohan Jit; Agarwal, Deepak; Garg, Ajay; Rath, Goura Kishore; Julka, Pramod Kumar; Kumar, Pratik; Thulkar, Sanjay; Sharma, Bhawani Shankar

2016-01-01

Objective: Purpose of the study is to verify the Gamma Knife Extend™ system (ES) based fractionated stereotactic radiosurgery with newly developed head-thorax phantom. Methods: Phantoms are extensively used to measure radiation dose and verify treatment plan in radiotherapy. A human upper body shaped phantom with thorax was designed to simulate fractionated stereotactic radiosurgery using Extend™ system of Gamma Knife. The central component of the phantom aids in performing radiological precision test, dosimetric evaluation and treatment verification. A hollow right circular cylindrical space of diameter 7.0 cm was created at the centre of this component to place various dosimetric devices using suitable adaptors. The phantom is made of poly methyl methacrylate (PMMA), a transparent thermoplastic material. Two sets of disk assemblies were designed to place dosimetric films in (1) horizontal (xy) and (2) vertical (xz) planes. Specific cylindrical adaptors were designed to place thimble ionization chamber inside phantom for point dose recording along xz axis. EBT3 Gafchromic films were used to analyze and map radiation field. The focal precision test was performed using 4 mm collimator shot in phantom to check radiological accuracy of treatment. The phantom head position within the Extend™ frame was estimated using encoded aperture measurement of repositioning check tool (RCT). For treatment verification, the phantom with inserts for film and ion chamber was scanned in reference treatment position using X-ray computed tomography (CT) machine and acquired stereotactic images were transferred into Leksell Gammaplan (LGP). A patient treatment plan with hypo-fractionated regimen was delivered and identical fractions were compared using EBT3 films and in-house MATLAB codes. Results: RCT measurement showed an overall positional accuracy of 0.265 mm (range 0.223 mm–0.343 mm). Gamma index analysis across fractions exhibited close agreement between LGP and film

Computational fluid dynamics (CFD) simulation of a newly designed passive particle sampler.

Science.gov (United States)

Sajjadi, H; Tavakoli, B; Ahmadi, G; Dhaniyala, S; Harner, T; Holsen, T M

2016-07-01

In this work a series of computational fluid dynamics (CFD) simulations were performed to predict the deposition of particles on a newly designed passive dry deposition (Pas-DD) sampler. The sampler uses a parallel plate design and a conventional polyurethane foam (PUF) disk as the deposition surface. The deposition of particles with sizes between 0.5 and 10 μm was investigated for two different geometries of the Pas-DD sampler for different wind speeds and various angles of attack. To evaluate the mean flow field, the k-ɛ turbulence model was used and turbulent fluctuating velocities were generated using the discrete random walk (DRW) model. The CFD software ANSYS-FLUENT was used for performing the numerical simulations. It was found that the deposition velocity increased with particle size or wind speed. The modeled deposition velocities were in general agreement with the experimental measurements and they increased when flow entered the sampler with a non-zero angle of attack. The particle-size dependent deposition velocity was also dependent on the geometry of the leading edge of the sampler; deposition velocities were more dependent on particle size and wind speeds for the sampler without the bend in the leading edge of the deposition plate, compared to a flat plate design. Foam roughness was also found to have a small impact on particle deposition. Copyright © 2016 Elsevier Ltd. All rights reserved.

[Bioethical analysis of the use of newly dead patients in medical learning].

Science.gov (United States)

Gomes, Andréia Patrícia; Rego, Sergio; Palácios, Marisa; Siqueira-Batista, Rodrigo

2010-01-01

The purpose of this article is to carry out, a discussion on the subject of bioethics and cadavers based upon a critic review of literature. A review of literature, was made with a survey of articles between 1977 and 2007 in the sites 'Biblioteca Virtual de Saúde', PubMed and SciElo, utilizing the keywords: newly deceased patients, newly dead patients, simulators,. This was complemented by a critical evaluation of books published in the area of ethics and bioethics. The possibility to develop learning without orientation by a supervisor is doubtful.. The utilization of newly dead for learning invasive procedures is very frequent and seldom admitted. These procedures, are usually, carried out secretly, without the knowledge and consent of the family. The ethical aspects of these practices are not discussed in the practical medical education. It essential that the ethics of use of recent deceased become a necessary content of graduate education. Performance of these procedures by students should always be authorized by family members. The simulators meet the requirements of training. Discussions about the ethical and bioethical aspects cannot be separated from practical considerations during the students learning time.

Weldability aspects of a newly developed duplex stainless steel LDX 2101

Energy Technology Data Exchange (ETDEWEB)

Westin, E.M. [Avesta Research Centre, Avesta (Sweden). Outokumpu Stainless; Brolund, B. [SSAB Tunnplat, Borlaenge (Sweden); Hertzman, S. [Outokumpu Stainless Research Foundation, Stockholm (Sweden)

2008-06-15

Duplex grades have, due to balanced chemical compositions of both filler and base metals, a weldability that allows for successful welding using a majority of the technically relevant techniques of today. In order to fulfil the performance requirements several aspects must be considered. In the heat affected zone (HAZ) the austenite reformation must be reasonably high and in the weld metal the microstructure must be stable so that e.g. high productivity welding and multi-pass welding are possible, without precipitation of detrimental phases in previous passes. This paper addresses the effect of alloying elements and thermal cycles on phase balance in the high temperature HAZ (HTHAZ) of the newly developed lean duplex grade LDX 2101 (EN 1.4162, UNS S32101). Bead-on-plate welds and simulated weld structures have been produced and investigated using metallography, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The results are analysed using the thermodynamic database Thermo-Calc and a model for phase transformation based on a paraequilibrium assumption for ferrite-austenite transformation. In the temperature region outside the paraequilibrium domain, growth controlled by diffusion of substitutional elements was considered. The analysis follows a model by Cahn regarding grain boundary nucleated growth and the Hillert-Engberg model on kinetics of spherical and planar growth. (orig.)

Parsing multiple processes of high temperature impacts on corn/soybean yield using a newly developed CLM-APSIM modeling framework

Science.gov (United States)

Peng, B.; Guan, K.; Chen, M.

2016-12-01

Future agricultural production faces a grand challenge of higher temperature under climate change. There are multiple physiological or metabolic processes of how high temperature affects crop yield. Specifically, we consider the following major processes: (1) direct temperature effects on photosynthesis and respiration; (2) speed-up growth rate and the shortening of growing season; (3) heat stress during reproductive stage (flowering and grain-filling); (4) high-temperature induced increase of atmospheric water demands. In this work, we use a newly developed modeling framework (CLM-APSIM) to simulate the corn and soybean growth and explicitly parse the above four processes. By combining the strength of CLM in modeling surface biophysical (e.g., hydrology and energy balance) and biogeochemical (e.g., photosynthesis and carbon-nitrogen interactions), as well as that of APSIM in modeling crop phenology and reproductive stress, the newly developed CLM-APSIM modeling framework enables us to diagnose the impacts of high temperature stress through different processes at various crop phenology stages. Ground measurements from the advanced SoyFACE facility at University of Illinois is used here to calibrate, validate, and improve the CLM-APSIM modeling framework at the site level. We finally use the CLM-APSIM modeling framework to project crop yield for the whole US Corn Belt under different climate scenarios.

Use of a newly developed active thermal neutron detector for in-phantom measurements in a medical LINAC

Energy Technology Data Exchange (ETDEWEB)

Bodogni, R.; Sanchez-Doblado, F.; Pola, A.; Gentile, A.; Esposito, A.; Gomez-ros, J. M.; Pressello, M. C.; Lagares, J. I.; Terron, J. A.; Gomez, F.

2013-07-01

In this work a newly developed active thermal neutron detector, based on a solid state analog device, was used to determine the thermal neutron fluence in selected positions of a simplified human phantom undergoing radiotherapy with a 15 MV LINAC. The results are compared with TLD, the predictions from a Monte Carlo simulation and with measurements indirectly performed with a digital device, located far from the phantom, inside the treatment room. In this work only TLD comparison is presented. Since active neutron instruments are usually affected by systematic deviations when used in a pulsed field with large photon background, the new detector offered in this work may represent an innovative and useful tool for neutron evaluations in accelerator-based radiotherapy. (Author)

Development and evaluation of a decision-based simulation for assessment of team skills.

Science.gov (United States)

Andrew, Brandon; Plachta, Stephen; Salud, Lawrence; Pugh, Carla M

2012-08-01

There is a need to train and evaluate a wide variety of nontechnical surgical skills. The goal of this project was to develop and evaluate a decision-based simulation to assess team skills. The decision-based exercise used our previously validated Laparoscopic Ventral Hernia simulator and a newly developed team evaluation survey. Five teams of 3 surgical residents (N = 15) were tasked with repairing a 10 × 10-cm right upper quadrant hernia. During the simulation, independent observers (N = 6) completed a 6-item survey assessing: (1) work quality; (2) communication; and (3) team effectiveness. After the simulation, team members self-rated their performance by using the same survey. Survey reliability revealed a Cronbach's alpha of r = .811. Significant differences were found when we compared team members' (T) and observers' (O) ratings for communication (T = 4.33/5.00 vs O = 3.00/5.00, P work quality (T = 4.33/5.00 vs O = 3.33/5.00, P performance on the simulator. Our current and previous work provides strong evidence that nontechnical and team related skills can be assessed without simulating a crisis situation. Copyright © 2012 Mosby, Inc. All rights reserved.

Improving a newly developed patient-reported outcome for thyroid patients, using cognitive interviewing

DEFF Research Database (Denmark)

Watt, Torquil; Rasmussen, Ase Krogh; Groenvold, Mogens

2008-01-01

Objective To improve a newly developed patient-reported outcome measure for thyroid patients using cognitive interviewing. Methods Thirty-one interviews using immediate retrospective and expansive probing were conducted among patients with non-toxic goiter (n = 4), nodular toxic goiter (n = 5) Gr...

Newly Developed Ceramic Membranes for Dehydration and Separation of Organic Mixtures by Pervaporation

NARCIS (Netherlands)

Gemert, van R.W.; Cuperus, F.P.

1995-01-01

Polymeric pervaporation membranes sometimes show great variety in performance when they are alternately used for different solvent mixtures. In addition, membrane stability in time is a problem in case of some solvents. Therefore, newly developed ceramic silica membranes with a 'dense' top layer

High-speed LWR transients simulation for optimizing emergency response

International Nuclear Information System (INIS)

Wulff, W.; Cheng, H.S.; Lekach, S.V.; Mallen, A.N.; Stritar, A.

1984-01-01

The purpose of computer-assisted emergency response in nuclear power plants, and the requirements for achieving such a response, are presented. An important requirement is the attainment of realistic high-speed plant simulations at the reactor site. Currently pursued development programs for plant simulations are reviewed. Five modeling principles are established and a criterion is presented for selecting numerical procedures and efficient computer hardware to achieve high-speed simulations. A newly developed technology for high-speed power plant simulation is described and results are presented. It is shown that simulation speeds ten times greater than real-time process-speeds are possible, and that plant instrumentation can be made part of the computational loop in a small, on-site minicomputer. Additional technical issues are presented which must still be resolved before the newly developed technology can be implemented in a nuclear power plant

The Development Needs of Newly Appointed Senior School Leaders in the Western Cape South Africa: A Case Study

Directory of Open Access Journals (Sweden)

Nelius Jansen van Vuuren

2017-12-01

Full Text Available The essential role that senior school leaders play in school leadership teams to ensure effective strategic leadership in schools has been the subject of intense discussion for many years. Crucial to this debate is the establishment of professional learning and leadership approaches for newly appointed senior school leaders. Recommendations for policy and practice highlight the importance of appropriate, multifaceted, developmental support initiatives for newly appointed school leaders. In many countries, including South Africa, a teaching qualification and, in most cases, extensive teaching experience is the only requirement for being appointed as a senior school leader in a school. This tends to suggest that no further professional development is required for newly appointed school leaders, the problem addressed in this paper. This paper reports on the main findings of the perceived development needs of newly appointed senior school leaders in the Western Cape, South Africa, and suggests that school leaders occupy a unique and specialist role in education, which requires relevant and specific preparation to support effective leadership. The respondents of this study report a lack of contextualised training and support before and after their appointment in their new roles creating unique development needs. This paper, therefore, employs a mixed-method approach to gather data to understand the perceived needs of twenty newly appointed senior school leaders in the Western Cape, South Africa.

Developing Software Simulations

Directory of Open Access Journals (Sweden)

Tom Hall

2007-06-01

Full Text Available Programs in education and business often require learners to develop and demonstrate competence in specified areas and then be able to effectively apply this knowledge. One method to aid in developing a skill set in these areas is through the use of software simulations. These simulations can be used for learner demonstrations of competencies in a specified course as well as a review of the basic skills at the beginning of subsequent courses. The first section of this paper discusses ToolBook, the software used to develop our software simulations. The second section discusses the process of developing software simulations. The third part discusses how we have used software simulations to assess student knowledge of research design by providing simulations that allow the student to practice using SPSS and Excel.

Validating self-reported mobile phone use in adults using a newly developed smartphone application

NARCIS (Netherlands)

Goedhart, Geertje; Kromhout, Hans; Wiart, Joe; Vermeulen, Roel

2015-01-01

OBJECTIVE: Interpretation of epidemiological studies on health effects from mobile phone use is hindered by uncertainties in the exposure assessment. We used a newly developed smartphone application (app) to validate self-reported mobile phone use and behaviour among adults. METHODS: 107

Micro-computed tomography newly developed for in vivo small animal imaging

International Nuclear Information System (INIS)

Arai, Yoshinori; Ninomiya, Tadashi; Kato, Takafumi; Masuda, Yuji

2005-01-01

The aim of this paper is to report a newly developed micro-computed tomography system for in vivo use. The system was composed of a micro-focus X-ray tube and an image intensifier (I.I.), both of which rotated around the object stage. A guinea pig and a rat were examined. The anesthetized animal was set on the secure object stage. Images of the head of the guinea pig and the tibia knee joint of the rat were taken. In addition, an image of the rat's tail was taken. The reconstruction and the image viewing were carried out using I-View software. The voxel matrix was 512 x 512 x 384. The voxel sizes ranged from 10 x 10 x 10 μm to 100 x 100 x 100 μm. The exposure time was 17 s, and the reconstruction time was 150 s. The head of the guinea pig and the tibia/knee joint of the rat were observed clearly under 100-μm and 30μm voxels, respectively. The trabecular bone of the tail was also observed clearly under a 10 μm voxel. The newly developed micro-computed tomography system makes it possible to obtain images of anesthetized animals set on a secure object stage. Clear bone images of the small animals could be obtained within a short time. (author)

Assessing College Students' Perceptions of a Case Teacher's Pedagogical Content Knowledge Using a Newly Developed Instrument

Science.gov (United States)

Jang, Syh-Jong

2011-01-01

Ongoing professional development for college teachers has been much emphasized. However, previous research on learning environments has seldom addressed college students' perceptions of teachers' PCK. This study aimed to evaluate college students' perceptions of a physics teacher's PCK development using a newly developed instrument and workshop…

Applicability of newly developed 610MPa class heavy thickness high strength steel to boiler pressure vessel

Energy Technology Data Exchange (ETDEWEB)

Katayama, Norihiko; Kaihara, Shoichiro; Ishii, Jun [Ishikawajima-Harima Heavy Industries Corp., Yokohama (Japan); Kajigaya, Ichiro [Ishikawajima-Harima Heavy Industries Corp., Tokyo (Japan); Totsuka, Takehiro; Miyazaki, Takashi [Ishikawajima-Harima Heavy Industries Corp., Aioi (Japan)

1995-11-01

Construction of a 350 MW Class PFBC (Pressurized Fluidized Bed Combustion) boiler plant is under planning in Japan. Design temperature and pressure of the vessel are maximum 350 C and 1.69 MPa, respectively. As the plate thickness of the vessel exceeds over 100 mm, high strength steel plate of good weldability and less susceptible to reheat cracking was required and developed. The steel was aimed to satisfy the tensile strength over 610 MPa at 350 C after postweld heat treatment (PWHT), with good notch toughness. The authors investigated the welding performances of the newly developed steel by using 150 mm-thick plate welded by pulsed-MAG and SAW methods. It was confirmed that the newly developed steel and its welds possess sufficient strength and toughness after PWHT, and applicable to the actual pressure vessel.

Fundamental Characteristics of the Newly Developed ATA™ Membrane Dialyzer.

Science.gov (United States)

Sunohara, Takashi; Masuda, Toshiaki

2017-01-01

Dialysis membranes are often made from synthetic polymers, such as polysulfone. However, membranes made from cellulose triacetate have superior biocompatibility and have been used since the 1980s. On-line hemodiafiltration treatment accompanied by massive fluid replacement is increasingly being used in Europe and Japan, but cellulose triacetate is not suitable for this treatment. Our newly developed asymmetric triacetate membrane, the ATA™ membrane, substantially improved the filtration properties and blood compatibility because of the asymmetric structure and smooth surface of this cellulose acetate membrane. Key Message: The ATA membrane maintains its high permeability even after massive filtration and shows less temporal variation in its permeation performance, lower protein adsorption, and superior biocompatibility compared with conventional membranes. © 2017 S. Karger AG, Basel.

Physicochemical properties of newly developed bioactive glass cement and its effects on various cells.

Science.gov (United States)

Washio, Ayako; Nakagawa, Aika; Nishihara, Tatsuji; Maeda, Hidefumi; Kitamura, Chiaki

2015-02-01

Biomaterials used in dental treatments are expected to have favorable properties such as biocompatibility and an ability to induce tissue formation in dental pulp and periapical tissue, as well as sealing to block external stimuli. Bioactive glasses have been applied in bone engineering, but rarely applied in the field of dentistry. In the present study, bioactive glass cement for dental treatment was developed, and then its physicochemical properties and effects on cell responses were analyzed. To clarify the physicochemical attributes of the cement, field emission scanning electron microscopy, X-ray diffraction, and pH measurement were carried out. Cell attachment, morphology, and viability to the cement were also examined to clarify the effects of the cement on odontoblast-like cells (KN-3 cells), osteoblastic cells (MC3T3-E1 cells), human periodontal ligament stem/progenitor cells and neuro-differentiative cells (PC-12 cells). Hydroxyapatite-like precipitation was formed on the surface of the hardened cement and the pH level changed from pH10 to pH9, then stabilized in simulate body fluid. The cement had no cytotxic effects on these cells, and particulary induced process elongation of PC-12 cells. Our results suggest that the newly developed bioactive glass cement have capability of the application in dental procedures as bioactive cement. © 2014 Wiley Periodicals, Inc.

Modeling and numerical techniques for high-speed digital simulation of nuclear power plants

International Nuclear Information System (INIS)

Wulff, W.; Cheng, H.S.; Mallen, A.N.

1987-01-01

Conventional computing methods are contrasted with newly developed high-speed and low-cost computing techniques for simulating normal and accidental transients in nuclear power plants. Six principles are formulated for cost-effective high-fidelity simulation with emphasis on modeling of transient two-phase flow coolant dynamics in nuclear reactors. Available computing architectures are characterized. It is shown that the combination of the newly developed modeling and computing principles with the use of existing special-purpose peripheral processors is capable of achieving low-cost and high-speed simulation with high-fidelity and outstanding user convenience, suitable for detailed reactor plant response analyses

PHL10/460: Cancerfacts.com - Vertical Portal with Newly Developed Health Profiler

OpenAIRE

Lenz, C; Brucksch, M

1999-01-01

Introduction Unlike general health portals such as WebMD and Drkoop.com that cover everything from the flu to heart disease, Silicon Valley-based cancerfacts.com is a so-called vertical portal. It covers only one small vertical niche of health care: cancer, and in particular, prostate cancer. As a value-added proprietary technology, the company offers its newly developed profile engine to health information retrievers. Methods Users are enabled to insert their specific medical information - r...

Newly developed semi-empirical formulas for (p, α) at 17.9 MeV and ...

Indian Academy of Sciences (India)

Home; Journals; Pramana – Journal of Physics; Volume 74; Issue 6. Newly developed semi-empirical formulas for (, ) at 17.9 MeV and (, ) at 22.3 MeV reaction cross-sections. Eyyup Tel Abdullah Aydin E Gamze Aydin Abdullah Kaplan Ömer Yavaş İskender A Reyhancan. Research Articles Volume 74 Issue 6 June ...

The newly developed Toyota plug-in hybrid system

Energy Technology Data Exchange (ETDEWEB)

Takaoka, Toshifumi; Ichinose, Hiroki [Toyota Motor Corporation (Japan)

2010-07-01

Toyota has been introducing several hybrid vehicles (HV) as a countermeasure to the automobile's concerns, like CO2 reduction, energy security, and emission reduction in urban areas. A next step towards an even more effective solution for these concerns is a plug-in hybrid vehicle (PHV). This vehicle combines the advantages of electric vehicles (EV), which use clean electric energy, and HV, with it's high environmental potential and user- friendliness comparable to conventional vehicles, such as a long cruising range. This paper describes a newly developed plug-in hybrid system and its vehicle performance. This system uses a Li-ion battery with high energy density and has an affordable EV range without sacrificing cabin space. The vehicle achieves a CO2 emission of 59g/km and meets the most stringent emission regulations in the world. The new PHV is a forerunner of the large-scale mass production PHV two years later. PHVs have the potential to become popular as a realistic solution towards sustainable mobility by renewable electricity usage in the future. (orig.)

How Schools Can Promote Healthy Development for Newly Arrived Immigrant and Refugee Adolescents: Research Priorities

Science.gov (United States)

McNeely, Clea A.; Morland, Lyn; Doty, S. Benjamin; Meschke, Laurie L.; Awad, Summer; Husain, Altaf; Nashwan, Ayat

2017-01-01

Background: The US education system must find creative and effective ways to foster the healthy development of the approximately 2 million newly arrived immigrant and refugee adolescents, many of whom contend with language barriers, limited prior education, trauma, and discrimination. We identify research priorities for promoting the school…

A computer literacy scale for newly enrolled nursing college students: development and validation.

Science.gov (United States)

Lin, Tung-Cheng

2011-12-01

Increasing application and use of information systems and mobile technologies in the healthcare industry require increasing nurse competency in computer use. Computer literacy is defined as basic computer skills, whereas computer competency is defined as the computer skills necessary to accomplish job tasks. Inadequate attention has been paid to computer literacy and computer competency scale validity. This study developed a computer literacy scale with good reliability and validity and investigated the current computer literacy of newly enrolled students to develop computer courses appropriate to students' skill levels and needs. This study referenced Hinkin's process to develop a computer literacy scale. Participants were newly enrolled first-year undergraduate students, with nursing or nursing-related backgrounds, currently attending a course entitled Information Literacy and Internet Applications. Researchers examined reliability and validity using confirmatory factor analysis. The final version of the developed computer literacy scale included six constructs (software, hardware, multimedia, networks, information ethics, and information security) and 22 measurement items. Confirmatory factor analysis showed that the scale possessed good content validity, reliability, convergent validity, and discriminant validity. This study also found that participants earned the highest scores for the network domain and the lowest score for the hardware domain. With increasing use of information technology applications, courses related to hardware topic should be increased to improve nurse problem-solving abilities. This study recommends that emphases on word processing and network-related topics may be reduced in favor of an increased emphasis on database, statistical software, hospital information systems, and information ethics.

Newly developed chitosan-silver hybrid nanoparticles: biosafety and apoptosis induction in HepG2 cells

International Nuclear Information System (INIS)

El-Sherbiny, Ibrahim M.; Salih, Ehab; Yassin, Abdelrahman M.; Hafez, Elsayed E.

2016-01-01

The present study reports the biosafety assessment, the exact molecular effects, and apoptosis induction of newly developed chitosan-silver hybrid nanoparticles (Cs–Ag NPs) in HepG2 cells. The investigated hybrid NPs were green synthesized using Cs/grape leaves aqueous extract (Cs/GLE) or Cs/GLE NPs as reducing and stabilizing agents. The successful formation of Cs/GLE NPs and Cs–Ag hybrid NPs has been confirmed by UV–Vis spectrophotometry, FTIR spectroscopy, XRD, and HRTEM. From the TEM analysis, the prepared Cs/GLE NPs are uniform and spherical with an average size of 150 nm, and the AgNPs (5–10 nm) were formed mainly on their surface. The UV–Vis spectra of Cs–Ag NPs showed a surface plasmon resonance (SPR) peak at about 450 nm confirming their formation. The synthesized Cs–Ag NPs were found to be crystalline as shown by XRD patterns with fcc phase oriented along the (111), (200), (220), and (311) planes. The cytotoxicity patterns, the antiproliferative activities, and the possible mechanisms of anticancer activity at molecular level of the newly developed Cs–Ag hybrid NPs were investigated. Cytotoxicity patterns of all the preparations demonstrated that the nontoxic treatment concentrations are ranged from 0.39 to 50 %, and many of the newly prepared Cs–Ag hybrid NPs showed high anticancer activities against HpG2 cells, and induced cellular apoptosis by downregulating BCL2 gene and upregulating P53.Graphical Abstract

Newly developed chitosan-silver hybrid nanoparticles: biosafety and apoptosis induction in HepG2 cells

Energy Technology Data Exchange (ETDEWEB)

El-Sherbiny, Ibrahim M., E-mail: ielsherbiny@Zewailcity.edu.eg; Salih, Ehab [Zewail City of Science and Technology, Center for Materials Science (Egypt); Yassin, Abdelrahman M. [Genetic Engineering and Biotechnology Research Institute, City of Scientific Research and Technology Applications, Biopharmaceutical Product Research Department (Egypt); Hafez, Elsayed E. [City of Scientific Research and Technology Applications, Plant Protection and Biomolecular Diagnosis Department (Egypt)

2016-07-15

The present study reports the biosafety assessment, the exact molecular effects, and apoptosis induction of newly developed chitosan-silver hybrid nanoparticles (Cs–Ag NPs) in HepG2 cells. The investigated hybrid NPs were green synthesized using Cs/grape leaves aqueous extract (Cs/GLE) or Cs/GLE NPs as reducing and stabilizing agents. The successful formation of Cs/GLE NPs and Cs–Ag hybrid NPs has been confirmed by UV–Vis spectrophotometry, FTIR spectroscopy, XRD, and HRTEM. From the TEM analysis, the prepared Cs/GLE NPs are uniform and spherical with an average size of 150 nm, and the AgNPs (5–10 nm) were formed mainly on their surface. The UV–Vis spectra of Cs–Ag NPs showed a surface plasmon resonance (SPR) peak at about 450 nm confirming their formation. The synthesized Cs–Ag NPs were found to be crystalline as shown by XRD patterns with fcc phase oriented along the (111), (200), (220), and (311) planes. The cytotoxicity patterns, the antiproliferative activities, and the possible mechanisms of anticancer activity at molecular level of the newly developed Cs–Ag hybrid NPs were investigated. Cytotoxicity patterns of all the preparations demonstrated that the nontoxic treatment concentrations are ranged from 0.39 to 50 %, and many of the newly prepared Cs–Ag hybrid NPs showed high anticancer activities against HpG2 cells, and induced cellular apoptosis by downregulating BCL2 gene and upregulating P53.Graphical Abstract.

Development of educational Web-based simulator for the electricity spot market in Korea

International Nuclear Information System (INIS)

Lee, J.W.; Yang, K.M.; Jeong, Y.W.; Park, J.B.; Shin, J.R.

2006-01-01

Market simulation approaches are used frequently by electric utilities to resolve the spot market-related problems that are often encountered in competitive electricity markets. A well constructed market simulator offers the possibility to foresee the effect of new market structures or rules before they are actually implemented. This paper presented a newly developed educational market simulator that simulates the power exchange methods and market rules of the Two Way Bidding Pool (TWBP) in Korea. It allows users to set information related with market and market entities. In particular, it is an educational tool that enables interaction between lecturers and students via Web-based programs. Students can learn the effectiveness of an electricity spot market by bidding and examining the market with lecturers. Measures have been taken to address the problem of multi-users trying to manage the complex data sets. The developed application program is composed of 3 tiers where the middle tier is logically divided into 2 kinds of application programs. The divided application programs are interconnected by using the Web-service based on Extended Markup Technology and Hyper Text Transfer Protocol which make the distributed computing technology possible. Unlike most existing educational simulators, this one has the advantage of allowing students to make bids just like in a real market, thus showing them how the real electricity market runs and how market participants make their revenues. 10 refs., 4 tabs., 13 figs

Development of educational Web-based simulator for the electricity spot market in Korea

Energy Technology Data Exchange (ETDEWEB)

Lee, J.W.; Yang, K.M.; Jeong, Y.W.; Park, J.B.; Shin, J.R. [Konkuk Univ., Seoul (Korea, Republic of). Dept. of Electrical Engineering

2006-07-01

Market simulation approaches are used frequently by electric utilities to resolve the spot market-related problems that are often encountered in competitive electricity markets. A well constructed market simulator offers the possibility to foresee the effect of new market structures or rules before they are actually implemented. This paper presented a newly developed educational market simulator that simulates the power exchange methods and market rules of the Two Way Bidding Pool (TWBP) in Korea. It allows users to set information related with market and market entities. In particular, it is an educational tool that enables interaction between lecturers and students via Web-based programs. Students can learn the effectiveness of an electricity spot market by bidding and examining the market with lecturers. Measures have been taken to address the problem of multi-users trying to manage the complex data sets. The developed application program is composed of 3 tiers where the middle tier is logically divided into 2 kinds of application programs. The divided application programs are interconnected by using the Web-service based on Extended Markup Technology and Hyper Text Transfer Protocol which make the distributed computing technology possible. Unlike most existing educational simulators, this one has the advantage of allowing students to make bids just like in a real market, thus showing them how the real electricity market runs and how market participants make their revenues. 10 refs., 4 tabs., 13 figs.

Accumulation of operational history through emulation test to meet proven technology requirement for newly developed I and C technology

International Nuclear Information System (INIS)

Yeong Cheol, Shin; Sung Kon, Kang; Han Seong, Son

2006-01-01

As new advanced digital I and C technology with potential benefits of higher functionality and better cost effectiveness is available in the market, NPP (Nuclear Power Plant) operators are inclined to use the new technology for the construction of new plant and the upgrade of existing plants. However, this new technology poses risks to the NPP operators at the same time. These risks are mainly due to the poor reliability of newly developed technology. KHNP's past experiences with the new equipment shows many cases of reliability problems. And their consequences include unintended plant trips, lowered acceptance of the new digital technology by the plant I and C maintenance crew, and increased licensing burden in answering for questions from the nuclear regulatory body. Considering the fact that the risk of these failures in the nuclear plant operation is far greater than those in other industry, nuclear power plant operators want proven technology for I and C systems. This paper presents an approach for the emulation of operational history through which a newly developed technology becomes a proven technology. One of the essential elements of this approach is the feedback scheme of running the new equipment in emulated environment, gathering equipment failure, and correcting the design(and test bed). The emulation of environment includes normal and abnormal events of the new equipment such as reconfiguration of control system due to power failure, plant operation including full spectrum of credible scenarios in an NPP. Emulation of I and C equipment execution mode includes normal operation, initialization and termination, abnormal operation, hardware maintenance and maintenance of algorithm/software. Plant specific simulator is used to create complete profile of plant operational conditions that I and C equipment is to experience in the real plant. Virtual operating crew technology is developed to run the simulator scenarios without involvement of actual operators

Development of simulators for SMRs

International Nuclear Information System (INIS)

Jafri, M.N.; Butt, P.

1998-01-01

The first step towards the introduction of simulator culture in Pakistan Atomic Energy Commission (PAEC) was taken in 1976 when the work on the development of analog computer based Basic Principles Simulator of KANUPP was initiated to test the Modified Real Time Control software. The project was revitalized in 1988 to develop a digital computer model of major KANUPP systems along with real-time simulation executive software and man-machine interface software in FORTRAN-77 on VAX-11/780. This simulator was later ported on microcomputers using C-language with four display units, entitled as KANUPP Test Simulator (KTS), and is presently being employed for training and teaching at KANUPP Inplant Plant Training Center(INPTC) and Institute of Nuclear Power Engineering (KINPOE) respectively. The acquisition of Advanced Process Simulator Software (APROS) in 1991 laid the foundation for establishing an enhanced simulator environment to meet the present day requirements and scope of simulators. The development of APROS based Engineering Analyzer for KANUPP was initiated in 1992. With the contract for 300 MWe two loop PWR nuclear power plant from China the development of Full Scope Training Simulator for CHASNUPP-1 was initiated in 1993, which is scheduled to be completed in end 1997. The process of development of simulators for SMRs provided the opportunities to achieve indigenous capabilities for the design and development of control room with real time I/O interface, real time data communication using RTPs and a general purpose security guarded real-time graphics display system, as well as considerable experience on the design and development of SMRs simulators. This paper presents information on the present state of SMRs simulator development and the achievements made in PAEC. (author)

A newly development RIA for thyroid hormone autoantibodies (THAAb)

International Nuclear Information System (INIS)

Li Fengying; Gu Liqiong; Chen Xiayin; Jin Yan; Chen Shuxian; Zhang Qun; Qiu Hongxia; Yang Jingren; Zhao Yongju; Chen Mingdao

2004-01-01

Objective: To report a newly developed RIA for THAAb from this laboratory. Methods: The tested serum samples were cultured with labelled thyroid hormone analogous ( 125 I T 3 , 125 I T 4 ) for 16 hours. Antigen-antibody complex was precipitated with anti-human IgG (immune precipitation method) and radio-activity determined. Results: The mean positive rate of THAAb in healthy euthyroid controls (n=186) was only 1.07%. The mean positive rate in patients with thyroid disorders was 14.4% (mean rate 13.5% in hyperthyroid subjects, n=118 and mean rate 15.2% in hypothyroid subjects, n=72). The serum THAAb titer could be markedly lowered after adding non-labelled thyroid hormones (P 3 and FT 4 would be significantly lowered (P 3 , FT 4 levels. In patients with positive THAAb (about 14.4% in patients with all thyroid disorders), the FT 3 , FT 4 levels were best determined after PEG precipitation. (authors)

Laser Nitriding of the Newly Developed Ti-20Nb-13Zr at.% Biomaterial Alloy to Enhance Its Mechanical and Corrosion Properties in Simulated Body Fluid

Science.gov (United States)

Hussein, M. A.; Kumar, A. Madhan; Yilbas, Bekir S.; Al-Aqeeli, N.

2017-11-01

Despite the widespread application of Ti alloy in the biomedical field, surface treatments are typically applied to improve its resistance to corrosion and wear. A newly developed biomedical Ti-20Nb-13Zr at.% alloy (TNZ) was laser-treated in nitrogen environment to improve its surface characteristics with corrosion protection performance. Surface modification of the alloy by laser was performed through a Nd:YAG laser. The structural and surface morphological alterations in the laser nitrided layer were investigated by XRD and a FE-SEM. The mechanical properties have been evaluated using nanoindentation for laser nitride and as-received samples. The corrosion protection behavior was estimated using electrochemical corrosion analysis in a physiological medium (SBF). The obtained results revealed the production of a dense and compact film of TiN fine grains (micro-/nanosize) with 9.1 µm below the surface. The mechanical assessment results indicated an improvement in the modulus of elasticity, hardness, and resistance of the formed TiN layer to plastic deformation. The electrochemical analysis exhibited that the surface protection performance of the laser nitrided TNZ substrates in the SBF could be considerably enhanced compared to that of the as-received alloy due to the presence of fine grains in the TiN layer resulting from laser nitriding. Furthermore, the untreated and treated Ti-20Nb-13Zr alloy exhibited higher corrosion resistance than the CpTi and Ti6Al4V commercial alloys. The improvements in the surface hardness and corrosion properties of Ti alloy in a simulated body obtained using laser nitriding make this approach a suitable candidate for enhancing the properties of biomaterials.

Muscle Attenuation Is Associated With Newly Developed Hypertension in Men of African Ancestry.

Science.gov (United States)

Zhao, Qian; Zmuda, Joseph M; Kuipers, Allison L; Bunker, Clareann H; Patrick, Alan L; Youk, Ada O; Miljkovic, Iva

2017-05-01

Increased ectopic adipose tissue infiltration in skeletal muscle is associated with insulin resistance and diabetes mellitus. We evaluated whether change in skeletal muscle adiposity predicts subsequent development of hypertension in men of African ancestry, a population sample understudied in previous studies. In the Tobago Health Study, a prospective longitudinal study among men of African ancestry (age range 40-91 years), calf intermuscular adipose tissue, and skeletal muscle attenuation were measured with computed tomography. Hypertension was defined as a systolic blood pressure ≥140 mm Hg, or a diastolic blood pressure ≥90 mm Hg, or receiving antihypertensive medications. Logistic regression was performed with adjustment for age, insulin resistance, baseline and 6-year change in body mass index, baseline and 6-year change in waist circumference, and other potential confounding factors. Among 746 normotensive men at baseline, 321 (43%) developed hypertension during the mean 6.2 years of follow-up. Decreased skeletal muscle attenuation was associated with newly developed hypertension after adjustment for baseline and 6-year change of body mass index (odds ratio [95% confidence interval] per SD, 1.3 [1.0-1.6]) or baseline and 6-year change of waist circumference (odds ratio [95% confidence interval] per SD, 1.3 [1.0-1.6]). No association was observed between increased intermuscular adipose tissue and hypertension. Our novel findings show that decreased muscle attenuation is associated with newly developed hypertension among men of African ancestry, independent of general and central adiposity and insulin resistance. Further studies are needed to adjust for inflammation, visceral and other ectopic adipose tissue depots, and to confirm our findings in other population samples. © 2017 American Heart Association, Inc.

Development and Application of SKSSIM Simulation Software for the Oxygen Bottom Blown Copper Smelting Process

Directory of Open Access Journals (Sweden)

Qinmeng Wang

2017-10-01

Full Text Available The oxygen bottom blown copper smelting process (SKS process is a newly developed intense smelting process, which has been widely applied to copper production in China. A multiphase equilibrium model for the SKS process was established based on its mechanism characteristics and the principle of Gibbs energy minimization, and an efficient simulation software—SKSSIM (SKS Simulation—was developed based on the model. Industrial data from the SKS process were used to compare with the calculated data from the SKSSIM software. The calculated data on the compositions of slag and matte as well as the distribution ratios of minor elements (such as Pb, Zn, As, Sb and Bi among the slags, mattes and off-gases were in good agreement with the actual plant data. Accordingly, the SKSSIM simulation software has the potentail to be used for the prediction of smelting production and for optimizing the operating parameters of the SKS process.

Development of sensorless easy-to-use overhead crane system via simulation based control

Science.gov (United States)

Tagawa, Yasutaka; Mori, Yoshihito; Wada, Masaomi; Kawajiri, Eisaku; Nouzuka, Kazuma

2016-09-01

This paper describes the newly developed overhead crane which has a sensorless vibration control system. Generally, loads which are carried by the overhead cranes are easy to vibrate and only skilled people can operate the cranes. Therefore, a lot of studies have been done to solve this problem by using feedback control with vibration sensors. However vibration sensors often break down in severe industrial environment and more reliable control systems are required. For this reason, we have been developing sensorless control system for overhead cranes. In this paper, we firstly introduce basic idea of simulation based control which is called IDCS, then overview and modeling of the overhead crane is presented. Next, the control system design of the overhead crane is discussed, and experimental results are shown for real overhead crane with 2 axes.

Reactor simulator development. Workshop material

International Nuclear Information System (INIS)

2001-01-01

The International Atomic Energy Agency (IAEA) has established a programme in nuclear reactor simulation computer programs to assist its Member States in education and training. The objective is to provide, for a variety of advanced reactor types, insight and practice in reactor operational characteristics and their response to perturbations and accident situations. To achieve this, the IAEA arranges for the supply or development of simulation programs and training material, sponsors training courses and workshops, and distributes documentation and computer programs. This publication consists of course material for workshops on development of such reactor simulators. Participants in the workshops are provided with instruction and practice in the development of reactor simulation computer codes using a model development system that assembles integrated codes from a selection of pre-programmed and tested sub-components. This provides insight and understanding into the construction and assumptions of the codes that model the design and operational characteristics of various power reactor systems. The main objective is to demonstrate simple nuclear reactor dynamics with hands-on simulation experience. Using one of the modular development systems, CASSIM tm , a simple point kinetic reactor model is developed, followed by a model that simulates the Xenon/Iodine concentration on changes in reactor power. Lastly, an absorber and adjuster control rod, and a liquid zone model are developed to control reactivity. The built model is used to demonstrate reactor behavior in sub-critical, critical and supercritical states, and to observe the impact of malfunctions of various reactivity control mechanisms on reactor dynamics. Using a PHWR simulator, participants practice typical procedures for a reactor startup and approach to criticality. This workshop material consists of an introduction to systems used for developing reactor simulators, an overview of the dynamic simulation

Simulant Development for LAWPS Testing

Energy Technology Data Exchange (ETDEWEB)

Russell, Renee L. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Schonewill, Philip P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Burns, Carolyn A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2017-05-23

This report describes simulant development work that was conducted to support the technology maturation of the LAWPS facility. Desired simulant physical properties (density, viscosity, solids concentration, solid particle size), sodium concentrations, and general anion identifications were provided by WRPS. The simulant recipes, particularly a “nominal” 5.6M Na simulant, are intended to be tested at several scales, ranging from bench-scale (500 mL) to full-scale. Each simulant formulation was selected to be chemically representative of the waste streams anticipated to be fed to the LAWPS system, and used the current version of the LAWPS waste specification as a formulation basis. After simulant development iterations, four simulants of varying sodium concentration (5.6M, 6.0M, 4.0M, and 8.0M) were prepared and characterized. The formulation basis, development testing, and final simulant recipes and characterization data for these four simulants are presented in this report.

SimulaTE: simulating complex landscapes of transposable elements of populations.

Science.gov (United States)

Kofler, Robert

2018-04-15

Estimating the abundance of transposable elements (TEs) in populations (or tissues) promises to answer many open research questions. However, progress is hampered by the lack of concordance between different approaches for TE identification and thus potentially unreliable results. To address this problem, we developed SimulaTE a tool that generates TE landscapes for populations using a newly developed domain specific language (DSL). The simple syntax of our DSL allows for easily building even complex TE landscapes that have, for example, nested, truncated and highly diverged TE insertions. Reads may be simulated for the populations using different sequencing technologies (PacBio, Illumina paired-ends) and strategies (sequencing individuals and pooled populations). The comparison between the expected (i.e. simulated) and the observed results will guide researchers in finding the most suitable approach for a particular research question. SimulaTE is implemented in Python and available at https://sourceforge.net/projects/simulates/. Manual https://sourceforge.net/p/simulates/wiki/Home/#manual; Test data and tutorials https://sourceforge.net/p/simulates/wiki/Home/#walkthrough; Validation https://sourceforge.net/p/simulates/wiki/Home/#validation. robert.kofler@vetmeduni.ac.at.

Predictive score for the development or progression of Graves' orbitopathy in patients with newly diagnosed Graves' hyperthyroidism

DEFF Research Database (Denmark)

Wiersinga, Wilmar; Žarković, Miloš; Bartalena, Luigi

2018-01-01

OBJECTIVE: To construct a predictive score for the development or progression of Graves' orbitopathy (GO) in Graves' hyperthyroidism (GH). DESIGN: Prospective observational study in patients with newly diagnosed GH, treated with antithyroid drugs (ATD) for 18 months at ten participating centers f...

Pressure drop performance evaluation for test assemblies with the newly developed top and bottom nozzles

International Nuclear Information System (INIS)

Lee, S. K.; Park, N. K.; Su, J. M.; Kim, H. K.; Lee, J. N.; Kim, K. T.

2003-01-01

To perform the hydraulic test for the newly developed top and bottom nozzles, two kinds of test assemblies were manufactured i. e. one is the test assembly which has the newly developed top and bottom nozzles and the other is Guardian test assembly which is commercially in mass production now. The test results show that the test assembly with one top nozzle and two bottom nozzles has a greater pressure loss coefficient than Guardian test assembly by 60.9% and 90.4% at the bottom nozzle location. This cause is due to the debris filtering plate for bottom nozzle to improve a filtering efficiency aginst foreign material. In the region of mid grid and top nozzle, there is no difference in pressure loss coefficient between the test assemblies since the componet features in these regions are very similar or same each other. The loss coefficients are 14.2% and 21.9% for model A and B respectively in the scale of test assembly, and the value would be within the 10% in the scale of real fuel assembly. As a result of hydraulic performance evaluation, model A is superior to model B

Development and user validation of driving tasks for a power wheelchair simulator.

Science.gov (United States)

Archambault, Philippe S; Blackburn, Émilie; Reid, Denise; Routhier, François; Miller, William C

2017-07-01

Mobility is important for participation in daily activities and a power wheelchair (PW) can improve quality of life of individuals with mobility impairments. A virtual reality simulator may be helpful in complementing PW skills training, which is generally seen as insufficient by both clinicians and PW users. To this end, specific, ecologically valid activities, such as entering an elevator and navigating through a shopping mall crowd, have been added to the McGill wheelchair (miWe) simulator through a user-centred approach. The objective of this study was to validate the choice of simulated activities in a group of newly trained PW users. We recruited 17 new PW users, who practiced with the miWe simulator at home for two weeks. They then related their experience through the Short Feedback Questionnaire, the perceived Ease of Use Questionnaire, and semi-structured interviews. Participants in general greatly appreciated their experience with the simulator. During the interviews, this group made similar comments about the activities as our previous group of expert PW users had done. They also insisted on the importance of realism in the miWe activities, for their use in training. A PW simulator may be helpful if it supports the practice of activities in specific contexts (such as a bathroom or supermarket), to complement the basic skills training received in the clinic (such as driving forward, backward, turning, and avoiding obstacles). Implications for Rehabilitation New power wheelchair users appreciate practicing on a virtual reality simulator and find the experience useful when the simulated diving activities are realistic and ecologically valid. User-centred development can lead to simulated power wheelchair activities that adequately capture everyday driving challenges experienced in various environmental contexts.

How Schools Can Promote Healthy Development for Newly Arrived Immigrant and Refugee Adolescents: Research Priorities.

Science.gov (United States)

McNeely, Clea A; Morland, Lyn; Doty, S Benjamin; Meschke, Laurie L; Awad, Summer; Husain, Altaf; Nashwan, Ayat

2017-02-01

The US education system must find creative and effective ways to foster the healthy development of the approximately 2 million newly arrived immigrant and refugee adolescents, many of whom contend with language barriers, limited prior education, trauma, and discrimination. We identify research priorities for promoting the school success of these youth. The study used the 4-phase priority-setting method of the Child Health and Nutrition Research Initiative. In the final stage, 132 researchers, service providers, educators, and policymakers based in the United States were asked to rate the importance of 36 research options. The highest priority research options (range 1 to 5) were: evaluating newcomer programs (mean = 4.44, SD = 0.55), identifying how family and community stressors affect newly arrived immigrant and refugee adolescents' functioning in school (mean = 4.40, SD = 0.56), identifying teachers' major stressors in working with this population (mean = 4.36, SD = 0.72), and identifying how to engage immigrant and refugee families in their children's education (mean = 4.35, SD = 0.62). These research priorities emphasize the generation of practical knowledge that could translate to immediate, tangible benefits for schools. Funders, schools, and researchers can use these research priorities to guide research for the highest benefit of schools and the newly arrived immigrant and refugee adolescents they serve. © 2017, American School Health Association.

Landfill mining: Development of a cost simulation model.

Science.gov (United States)

Wolfsberger, Tanja; Pinkel, Michael; Polansek, Stephanie; Sarc, Renato; Hermann, Robert; Pomberger, Roland

2016-04-01

Landfill mining permits recovering secondary raw materials from landfills. Whether this purpose is economically feasible, however, is a matter of various aspects. One is the amount of recoverable secondary raw material (like metals) that can be exploited with a profit. Other influences are the costs for excavation, for processing the waste at the landfill site and for paying charges on the secondary disposal of waste. Depending on the objectives of a landfill mining project (like the recovery of a ferrous and/or a calorific fraction) these expenses and revenues are difficult to assess in advance. This situation complicates any previous assessment of the economic feasibility and is the reason why many landfills that might be suitable for landfill mining are continuingly operated as active landfills, generating aftercare costs and leaving potential hazards to later generations. This article presents a newly developed simulation model for landfill mining projects. It permits identifying the quantities and qualities of output flows that can be recovered by mining and by mobile on-site processing of the waste based on treatment equipment selected by the landfill operator. Thus, charges for disposal and expected revenues from secondary raw materials can be assessed. Furthermore, investment, personnel, operation, servicing and insurance costs are assessed and displayed, based on the selected mobile processing procedure and its throughput, among other things. For clarity, the simulation model is described in this article using the example of a real Austrian sanitary landfill. © The Author(s) 2016.

Driving Simulator Development and Performance Study

OpenAIRE

Juto, Erik

2010-01-01

The driving simulator is a vital tool for much of the research performed at theSwedish National Road and Transport Institute (VTI). Currently VTI posses three driving simulators, two high fidelity simulators developed and constructed by VTI, and a medium fidelity simulator from the German company Dr.-Ing. Reiner Foerst GmbH. The two high fidelity simulators run the same simulation software, developed at VTI. The medium fidelity simulator runs a proprietary simulation software. At VTI there is...

Microcanonical simulation of a toy model with vacuum seizing

International Nuclear Information System (INIS)

Stone, M.

1984-01-01

Tested was a newly developed method for simulating field theories with fermionic degrees of freedom on a simple quantum mechanical model which still has enough structure to exhibit symmetry breaking and other effects due to anomalies

Development of Simulator Configuration Tool

International Nuclear Information System (INIS)

Nedrelid, Olav; Pettersen, Geir

1996-01-01

The main objective of the development of a Simulator Configuration Tool (SCT) is to achieve faster and more efficient production of dynamic simulators. Through application of versatile graphical interfaces, the simulator builder should be able to configure different types of simulators including full-scope process simulators. The SCT should be able to serve different simulator environments. The configuration tool communicates with simulator execution environments through a TCP/IP-based interface, Communication with a Model Server System developed at Institutt for energiteknikk has been established and used as test case. The system consists of OSF/Motif dialogues for operations requiring textual input, list selections etc., and uses the Picasso-3 User Interface Management System to handle presentation of static and dynamic graphical information. (author)

Development of training simulator for LWR

International Nuclear Information System (INIS)

Sureshbabu, R.M.

2009-01-01

A full-scope training simulator was developed for a light water reactor (LWR). This paper describes how the development evolved from a desktop simulator to the full-scope training simulator. It also describes the architecture and features of the simulator including the large number of failures that it simulates. The paper also explains the three-level validation tests that were used to qualify the training simulator. (author)

An Experimental Study on Dynamics of a Novel Dual-Belt Continuous Variable Transmission Based on a Newly Developed Test Rig

Directory of Open Access Journals (Sweden)

Pak Kin Wong

2015-01-01

Full Text Available A novel dual-belt Van Doorne’s continuous variable transmission (DBVCVT system, which is applicable to heavy-duty vehicles, has been previously proposed by the authors in order to improve the low torque capacity of traditional single-belt CVT. This DBVCVT is a novel design among continuously variable transmissions and is necessary to be prototyped for experimental study, and the analytical dynamic model for this DBVCVT also needs to be experimentally validated. So, this work originally fabricated a prototype of DBVCVT and integrates this prototype to a light-load hardware-in-the-loop test rig by replacing the engine and load equipment with the AC motor and magnetic powder dynamometer. Moreover, with the use of this newly developed test rig, this work implements the experimental study of this DBVCVT for the first time. The comparison of experimental and simulation results validates the previously proposed analytical model for DBVCVT, and some basic characteristics of the DBVCVT in terms of the reliability, speed ratio, and transmission efficiency are also experimentally studied. In all, this developed test rig with the analytical model lays the foundation for further study on this novel DBVCVT.

Association Between Manual Loading and Newly Developed Carpal Tunnel Syndrome in Subjects With Physical Disabilities: A Follow-Up Study.

Science.gov (United States)

Lin, Yen-Nung; Chiu, Chun-Chieh; Huang, Shih-Wei; Hsu, Wen-Yen; Liou, Tsan-Hon; Chen, Yi-Wen; Chang, Kwang-Hwa

2017-10-01

To identify the association between body composition and newly developed carpal tunnel syndrome (CTS) and to search for the best probabilistic cutoff value of associated factors to predict subjects with physical disabilities developing new CTS. Longitudinal. University-affiliated medical center. Subjects with physical disabilities (N=47; mean age ± SD, 42.1±7.7y). Not applicable. Median and ulnar sensory nerve conduction velocity (SNCV) were measured at the initial and follow-up tests (interval >2y). Total and regional body composition were measured with dual-energy x-ray absorptiometry at the initial test. Leg lean tissue percentage was calculated to delineate each participant's manual loading degree during locomotion. Leg lean tissue percentage is the lean tissue mass of both legs divided by body weight. Based on median SNCV changes, we divided all participants into 3 groups: subjects with bilateral CTS (median SNCV value normative ulnar SNCV value >37.8m/s) in the initial test (n=10), subjects with newly developed CTS in the follow-up test (n=8), and subjects without additional CTS in the follow-up test (n=27). Eight of 35 subjects not having bilateral CTS initially developed new CTS (8.8% per year; mean follow-up period, 2.6y). Leg lean tissue percentage was associated with the probability of newly developed CTS (adjusted odds ratio, .64; P12% were less likely to have developed new CTS at the follow-up test (sensitivity, .75; specificity, .85; area under the curve, .88; Pphysical disabilities. Therefore, a preventive program for those subjects at risk can start early. Copyright © 2017 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

Upgraded Features of Newly Constructed Fuel Assembly Mechanical Characterization Test Facility in KAERI

Energy Technology Data Exchange (ETDEWEB)

Lee, Kang Hee; Kang, Heung Seok; Yoon, Kyung Ho; Kim, Hyung Kyu; Lee, Young Ho; Kim, Soo Ho; Yang, Jae Ho [KAERI, Daejeon (Korea, Republic of)

2016-05-15

Fuel assembly mechanical characterization test facility (FAMeCT) in KAERI is newly constructed with upgraded functional features such as increased loading capacity, under-water vibration testing and severe earthquake simulation for extended fuel design guideline. The facility building is compactly designed in the scale of 3rd floor building and has regions for assembly-wise mechanical test equipment, dynamic load (seismic) simulating test system, small scale hydraulic loop and component wise test equipment. Figure 1 shows schematic regional layout of the facility building. Mechanical test platform and system is designed to increase loading capacity for axial compression test. Structural stability of the support system of new upper core plate simulator is validated through a limit case functional test. Fuel assembly mechanical characterization test facility in KAERI is newly constructed and upgraded with advanced functional features such as uprated loading capacity, under-water vibration testing and severe earthquake simulation for extended fuel design guideline. This paper briefly introduce the test facility construction and scope of the facility and is focused on the upgraded design features of the facility. Authors hope to facilitate the facility more in the future and collaborate with the industry.

Monte Carlo simulation of boron-ion implantation into single-crystal silicon

International Nuclear Information System (INIS)

Klein, K.M.

1991-01-01

A physically based Monte Carlo boron implantation model developed comprehends previously neglected but important implant parameters such as native oxide layers, wafer temperature, beam divergence, tilt angle, rotation (twist) angle, and dose, in addition to energy. This model uses as its foundation the MARLOWE Monte Carlo simulation code developed at Oak Ridge National Laboratory for the analysis of radiation effects in materials. This code was carefully adapted for the simulation of ion implantation, and a number of significant improvements have been made, including the addition of atomic pair specific interatomic potentials, the implementation of a newly developed local electron concentration dependent electronic stopping model, and the implementation of a newly developed cumulative damage model. This improved version of the code, known as UT-MARLOWE, allows boron implantation profiles to be accurately predicted as a function of energy, tilt angle, rotation angle, and dose. This code has also been used in the development and implementation of an accurate and efficient two-dimensional boron implantation model

The risk of newly developed visual impairment in treated normal-tension glaucoma: 10-year follow-up.

Science.gov (United States)

Choi, Yun Jeong; Kim, Martha; Park, Ki Ho; Kim, Dong Myung; Kim, Seok Hwan

2014-12-01

To investigate the risk and risk factors for newly developed visual impairment in treated patients with normal-tension glaucoma (NTG) followed up on for 10 years. Patients with NTG, who did not have visual impairment at the initial diagnosis and had undergone intraocular pressure (IOP)-lowering treatment for more than 7 years, were included on the basis of a retrospective chart review. Visual impairment was defined as either low vision (0.05 [20/400] ≤ visual acuity (VA) visual field (VF) visual impairment, Kaplan-Meier survival analysis and generalized linear mixed effects models were utilized. During the 10.8 years mean follow-up period, 20 eyes of 16 patients were diagnosed as visual impairment (12 eyes as low vision, 8 as blindness) among 623 eyes of 411 patients. The cumulative risk of visual impairment in at least one eye was 2.8% at 10 years and 8.7% at 15 years. The risk factors for visual impairment from treated NTG were worse VF mean deviation (MD) at diagnosis and longer follow-up period. The risk of newly developed visual impairment in the treated patients with NTG was relatively low. Worse VF MD at diagnosis and longer follow-up period were associated with development of visual impairment. © 2014 Acta Ophthalmologica Scandinavica Foundation. Published by John Wiley & Sons Ltd.

Modification of Core Model for KNTC 2 Simulator

Energy Technology Data Exchange (ETDEWEB)

Lee, Y.K.; Lee, J.G.; Park, J.E.; Bae, S.N.; Chin, H.C. [Korea Electric Power Research Institute, Taejeon (Korea, Republic of)

1997-12-31

KNTC 2 simulator was developed in 1986 referencing YGN 1. Since the YGN 1 has changed its fuel cycle to long term cycle(cycle 9), the data such as rod worth, boron worth, moderator temperature coefficient, and etc. of the simulator and those of the YGN 1 became different. To incorporate these changes into the simulator and make the simulator more close to the reference plant, core model upgrade became a necessity. During this research, core data for the simulator was newly generated using APA of the WH. And to make it easy tuning and verification of the key characteristics of the reactor model, PC-Based tool was also developed. And to facilitate later core model upgrade, two procedures-`the Procedures for core characteristic generation` and `the Procedures for core characteristic modification`-were also developed. (author). 16 refs., 22 figs., 1 tab.

Value of a newly sequenced bacterial genome

DEFF Research Database (Denmark)

Barbosa, Eudes; Aburjaile, Flavia F; Ramos, Rommel Tj

2014-01-01

and annotation will not be undertaken. It is important to know what is lost when we settle for a draft genome and to determine the "scientific value" of a newly sequenced genome. This review addresses the expected impact of newly sequenced genomes on antibacterial discovery and vaccinology. Also, it discusses...... heightened expectations that NGS would boost antibacterial discovery and vaccine development. Although many possible drug and vaccine targets have been discovered, the success rate of genome-based analysis has remained below expectations. Furthermore, NGS has had consequences for genome quality, resulting...

DeepSimulator: a deep simulator for Nanopore sequencing

KAUST Repository

Li, Yu

2017-12-23

Motivation: Oxford Nanopore sequencing is a rapidly developed sequencing technology in recent years. To keep pace with the explosion of the downstream data analytical tools, a versatile Nanopore sequencing simulator is needed to complement the experimental data as well as to benchmark those newly developed tools. However, all the currently available simulators are based on simple statistics of the produced reads, which have difficulty in capturing the complex nature of the Nanopore sequencing procedure, the main task of which is the generation of raw electrical current signals. Results: Here we propose a deep learning based simulator, DeepSimulator, to mimic the entire pipeline of Nanopore sequencing. Starting from a given reference genome or assembled contigs, we simulate the electrical current signals by a context-dependent deep learning model, followed by a base-calling procedure to yield simulated reads. This workflow mimics the sequencing procedure more naturally. The thorough experiments performed across four species show that the signals generated by our context-dependent model are more similar to the experimentally obtained signals than the ones generated by the official context-independent pore model. In terms of the simulated reads, we provide a parameter interface to users so that they can obtain the reads with different accuracies ranging from 83% to 97%. The reads generated by the default parameter have almost the same properties as the real data. Two case studies demonstrate the application of DeepSimulator to benefit the development of tools in de novo assembly and in low coverage SNP detection. Availability: The software can be accessed freely at: https://github.com/lykaust15/DeepSimulator.

Underground trials on a newly developed EDW 150-2 L unit

Energy Technology Data Exchange (ETDEWEB)

Wille, G.; Klimek, K.H.

1982-01-01

Coal-getting from medium thick coalbeds (> 1.7 m) requires high-performance shearer-loaders. Machine length and adjustability have to be such as to permit smooth cutting through geological faults. Furthermore they should be suitable to cut out niches for the AFC drives so that gateroads can be driven along with the face line. The newly developed EDW 150-2 L shearer-loader meets these expectations after various mechanical and electrical improvements. The unit proved its usefulness from the beginning and in the most difficult geological conditions where other shearer-loaders normally available for the range of coalbed thickness would mostly have failed. The multiple requirements and disturbances have led to a number of separate improvements and disturbances have led to a number of separate improvements which together contribute to a basic improvement of the machine concept as far as applications, operational flexibility and safety are concerned.

Development of the ATLAS simulation framework

International Nuclear Information System (INIS)

DellAcqua, A.; Stavrianakou, M.; Amako, K.; Kanzaki, J.; Morita, Y.; Murakami, K.; Sasaki; Kurashige, H.; Rimoldi, A.; Saeki, T.; Ueda, I.; Tanaka, S.; Yoshida, H.

2001-01-01

Object-oriented (OO) approach is the key technology to develop a software system in the LHC/ATLAS experiment. The authors developed a OO simulation framework based on the Geant4 general-purpose simulation toolkit. Because of complexity of simulation in ATLAS, the authors paid most attention to the scalability in the design. Although the first target to apply this framework is to implement the ATLAS full detector simulation program, there is no experiment-specific code in it, therefore it can be utilized for the development of any simulation package, not only for HEP experiments but also for various different research domains. The authors discuss our approach of design and implementation of the framework

Neonatology faculty development using simulation.

Science.gov (United States)

French, Heather M; Hales, Roberta L

2016-11-01

The goal of faculty development activities is to supply the public with knowledgeable, skilled, and competent physicians who are prepared for high performance in the dynamic and complex healthcare environment. Current faculty development programs lack evidence-based support and are not sufficient to meet the professional needs of practicing physicians. Simulation activities for faculty development offer an alternative to traditional, teacher-centric educational offerings. Grounded in adult learning theory, simulation is a learner-centric, interactive, efficient, and effective method to train busy professionals. Many of the faculty development needs of clinical neonatologists can be met by participating in simulation-based activities that focus on technical skills, teamwork, leadership, communication, and patient safety. Copyright © 2016 Elsevier Inc. All rights reserved.

Assessing the comparative effectiveness of newly marketed medications: methodological challenges and implications for drug development.

Science.gov (United States)

Schneeweiss, S; Gagne, J J; Glynn, R J; Ruhl, M; Rassen, J A

2011-12-01

Comparative-effectiveness research (CER) aims to produce actionable evidence regarding the effectiveness and safety of medical products and interventions as they are used outside of controlled research settings. Although CER evidence regarding medications is particularly needed shortly after market approval, key methodological challenges include (i) potential bias due to channeling of patients to the newly marketed medication because of various patient-, physician-, and system-related factors; (ii) rapid changes in the characteristics of the user population during the early phase of marketing; and (iii) lack of timely data and the often small number of users in the first few months of marketing. We propose a mix of approaches to generate comparative-effectiveness data in the early marketing period, including sequential cohort monitoring with secondary health-care data and propensity score (PS) balancing, as well as extended follow-up of phase III and phase IV trials, indirect comparisons of placebo-controlled trials, and modeling and simulation of virtual trials.

A Newly Improved Modified Method Development and Validation of Bromofenac Sodium Sesquihydrate in Bulk Drug Manufacturing

OpenAIRE

Sunil Kumar Yelamanchi V; Useni Reddy Mallu; I. V Kasi Viswanath; D. Balasubramanyam; G. Narshima Murthy

2016-01-01

The main objective of this study was to develop a simple, efficient, specific, precise and accurate newly improved modified Reverse Phase High Performance Liquid Chromatographic Purity (or) Related substance method for bromofenac sodium sesquihydrate active pharmaceuticals ingredient dosage form. Validation of analytical method is the confirmation by examination and the provision of objective evidence that the particular requirements for a specific intended use are fulfilled as per ICH, USP...

Development of an adjoint sensitivity field-based treatment-planning technique for the use of newly designed directional LDR sources in brachytherapy.

Science.gov (United States)

Chaswal, V; Thomadsen, B R; Henderson, D L

2012-02-21

The development and application of an automated 3D greedy heuristic (GH) optimization algorithm utilizing the adjoint sensitivity fields for treatment planning to assess the advantage of directional interstitial prostate brachytherapy is presented. Directional and isotropic dose kernels generated using Monte Carlo simulations based on Best Industries model 2301 I-125 source are utilized for treatment planning. The newly developed GH algorithm is employed for optimization of the treatment plans for seven interstitial prostate brachytherapy cases using mixed sources (directional brachytherapy) and using only isotropic sources (conventional brachytherapy). All treatment plans resulted in V100 > 98% and D90 > 45 Gy for the target prostate region. For the urethra region, the D10(Ur), D90(Ur) and V150(Ur) and for the rectum region the V100cc, D2cc, D90(Re) and V90(Re) all are reduced significantly when mixed sources brachytherapy is used employing directional sources. The simulations demonstrated that the use of directional sources in the low dose-rate (LDR) brachytherapy of the prostate clearly benefits in sparing the urethra and the rectum sensitive structures from overdose. The time taken for a conventional treatment plan is less than three seconds, while the time taken for a mixed source treatment plan is less than nine seconds, as tested on an Intel Core2 Duo 2.2 GHz processor with 1GB RAM. The new 3D GH algorithm is successful in generating a feasible LDR brachytherapy treatment planning solution with an extra degree of freedom, i.e. directionality in very little time.

Development of an adjoint sensitivity field-based treatment-planning technique for the use of newly designed directional LDR sources in brachytherapy

Science.gov (United States)

Chaswal, V.; Thomadsen, B. R.; Henderson, D. L.

2012-02-01

The development and application of an automated 3D greedy heuristic (GH) optimization algorithm utilizing the adjoint sensitivity fields for treatment planning to assess the advantage of directional interstitial prostate brachytherapy is presented. Directional and isotropic dose kernels generated using Monte Carlo simulations based on Best Industries model 2301 I-125 source are utilized for treatment planning. The newly developed GH algorithm is employed for optimization of the treatment plans for seven interstitial prostate brachytherapy cases using mixed sources (directional brachytherapy) and using only isotropic sources (conventional brachytherapy). All treatment plans resulted in V100 > 98% and D90 > 45 Gy for the target prostate region. For the urethra region, the D10Ur, D90Ur and V150Ur and for the rectum region the V100cc, D2cc, D90Re and V90Re all are reduced significantly when mixed sources brachytherapy is used employing directional sources. The simulations demonstrated that the use of directional sources in the low dose-rate (LDR) brachytherapy of the prostate clearly benefits in sparing the urethra and the rectum sensitive structures from overdose. The time taken for a conventional treatment plan is less than three seconds, while the time taken for a mixed source treatment plan is less than nine seconds, as tested on an Intel Core2 Duo 2.2 GHz processor with 1GB RAM. The new 3D GH algorithm is successful in generating a feasible LDR brachytherapy treatment planning solution with an extra degree of freedom, i.e. directionality in very little time.

Development of the simulation monitoring system

International Nuclear Information System (INIS)

Kato, Katsumi; Watanabe, Tadashi; Kume, Etsuo

2001-01-01

Large-scale simulation technique is studied at the Center for Promotion of Computational Science and Engineering for the computational science research in nuclear fields. Visualization and animation processing techniques are developed for efficient understanding of simulation results. The development of the simulation monitoring system, which is used for real-time visualization of ongoing simulations or for successive visualization of calculated results, is described in this report. The standard visualization tool AVS5 or AVS/EXPRESS is used for the simulation monitoring system, and thus, this system can be utilized in various computer environments. (author)

Development of space simulation / net-laboratory system

Science.gov (United States)

Usui, H.; Matsumoto, H.; Ogino, T.; Fujimoto, M.; Omura, Y.; Okada, M.; Ueda, H. O.; Murata, T.; Kamide, Y.; Shinagawa, H.; Watanabe, S.; Machida, S.; Hada, T.

A research project for the development of space simulation / net-laboratory system was approved by Japan Science and Technology Corporation (JST) in the category of Research and Development for Applying Advanced Computational Science and Technology(ACT-JST) in 2000. This research project, which continues for three years, is a collaboration with an astrophysical simulation group as well as other space simulation groups which use MHD and hybrid models. In this project, we develop a proto type of unique simulation system which enables us to perform simulation runs by providing or selecting plasma parameters through Web-based interface on the internet. We are also developing an on-line database system for space simulation from which we will be able to search and extract various information such as simulation method and program, manuals, and typical simulation results in graphic or ascii format. This unique system will help the simulation beginners to start simulation study without much difficulty or effort, and contribute to the promotion of simulation studies in the STP field. In this presentation, we will report the overview and the current status of the project.

Development and evaluation of a simulation-based continuing medical education course: beyond lectures and credit hours.

Science.gov (United States)

Pugh, Carla M; Arafat, Fahd O; Kwan, Calvin; Cohen, Elaine R; Kurashima, Yo; Vassiliou, Melina C; Fried, Gerald M

2015-10-01

The aim of our study was to modify our previously developed laparoscopic ventral hernia (LVH) simulator to increase difficulty and then reassess validity and feasibility for using the simulator in a newly developed simulation-based continuing medical education course. Participants (N = 30) were practicing surgeons who signed up for a hands-on postgraduate laparoscopic hernia course. An LVH simulator, with prior validity evidence, was modified for the course to increase difficulty. Participants completed 1 of the 3 variations in hernia anatomy: incarcerated omentum, incarcerated bowel, and diffuse adhesions. During the procedure, course faculty and peer observers rated surgeon performance using Global Operative Assessment of Laparoscopic Skills-Incisional Hernia and Global Operative Assessment of Laparoscopic Skills rating scales with prior validity evidence. Rating scale reliability was reassessed for internal consistency. Peer and faculty raters' scores were compared. In addition, quality and completeness of the hernia repairs were rated. Internal consistency on the general skills performance (peer α = .96, faculty α = .94) and procedure-specific performance (peer α = .91, faculty α = .88) scores were high. Peers were more lenient than faculty raters on all LVH items in both the procedure-specific skills and general skills ratings. Overall, participants scored poorly on the quality and completeness of their hernia repairs (mean = 3.90/16, standard deviation = 2.72), suggesting a mismatch between course attendees and hernia difficulty and identifying a learning need. Simulation-based continuing medical education courses provide hands-on experiences that can positively affect clinical practice. Although our data appear to show a significant mismatch between clinical skill and simulator difficulty, these findings also underscore significant learning needs in the surgical community. Copyright © 2015 Elsevier Inc. All rights reserved.

A Newly Developed Nested PCR Assay for the Detection of Helicobacter pylori in the Oral Cavity.

Science.gov (United States)

Ismail, Hawazen; Morgan, Claire; Griffiths, Paul; Williams, John; Jenkins, Gareth

2016-01-01

To develop a new nested polymerase chain reaction (PCR) assay for identifying Helicobacter pylori DNA from dental plaque. H. pylori is one of the most common chronic bacterial pathogens in humans. The accurate detection of this organism is essential for proper patient management and for the eradication of the bacteria following treatment. Forty-nine patients (24 males and 25 females; mean age: 51; range, 19 to 94 y) were investigated for the presence of H. pylori in dental plaque by single-step PCR and nested PCR and in the stomach by single-step PCR, nested PCR, and histologic examination. The newly developed nested PCR assay identified H. pylori DNA in gastric biopsies of 18 patients who were histologically classified as H. pylori-positive and 2 additional biopsies of patients who were H. pylori-negative by histologic examination (20/49; 40.8%). Dental plaque samples collected before and after endoscopy from the 49 patients revealed that single-step PCR did not detect H. pylori but nested PCR was able to detect H. pylori DNA in 40.8% (20/49) patients. Nested PCR gave a higher detection rate (40.8%, 20/49) than that of histology (36.7%, 18/49) and single-step PCR. When nested PCR results were compared with histology results there was no significant difference between the 2 methods. Our newly developed nested PCR assay is at least as sensitive as histology and may be useful for H. pylori detection in patients unfit for endoscopic examination.

Characteristics of bread prepared from wheat flours blended with various kinds of newly developed rice flours.

Science.gov (United States)

Nakamura, S; Suzuki, K; Ohtsubo, K

2009-04-01

Characteristics of the bread prepared from wheat flour blended with the flour of various kinds of newly developed rice cultivars were investigated. Qualities of the bread made from wheat flour blended with rice flour have been reported to be inferior to those from 100% wheat flour bread. To improve its qualities, we searched for the new-characteristic rice flours among the various kinds of newly developed rice cultivars to blend with the wheat flour for the bread preparation. The most suitable new characteristic rices are combination of purple waxy rice, high-amylose rice, and sugary rice. Specific volume of the bread from the combination of wheat and these 3 kinds of rice flours showed higher specific volume (3.93) compared with the traditional wheat/rice bread (3.58). We adopted the novel method, continuous progressive compression test, to measure the physical properties of the dough and the bread in addition to the sensory evaluation. As a result of the selection of the most suitable rice cultivars and blending ratio with the wheat flour, we could develop the novel wheat/rice bread, of which loaf volume, physical properties, and tastes are acceptable and resistant to firming on even 4 d after the bread preparation. To increase the ratio of rice to wheat, we tried to add a part of rice as cooked rice grains. The specific volume and qualities of the bread were maintained well although the rice content of total flour increased from 30% to 40%.

Establishment probability in newly founded populations

Directory of Open Access Journals (Sweden)

Gusset Markus

2012-06-01

Full Text Available Abstract Background Establishment success in newly founded populations relies on reaching the established phase, which is defined by characteristic fluctuations of the population’s state variables. Stochastic population models can be used to quantify the establishment probability of newly founded populations; however, so far no simple but robust method for doing so existed. To determine a critical initial number of individuals that need to be released to reach the established phase, we used a novel application of the “Wissel plot”, where –ln(1 – P0(t is plotted against time t. This plot is based on the equation P0t=1–c1e–ω1t, which relates the probability of extinction by time t, P0(t, to two constants: c1 describes the probability of a newly founded population to reach the established phase, whereas ω1 describes the population’s probability of extinction per short time interval once established. Results For illustration, we applied the method to a previously developed stochastic population model of the endangered African wild dog (Lycaon pictus. A newly founded population reaches the established phase if the intercept of the (extrapolated linear parts of the “Wissel plot” with the y-axis, which is –ln(c1, is negative. For wild dogs in our model, this is the case if a critical initial number of four packs, consisting of eight individuals each, are released. Conclusions The method we present to quantify the establishment probability of newly founded populations is generic and inferences thus are transferable to other systems across the field of conservation biology. In contrast to other methods, our approach disaggregates the components of a population’s viability by distinguishing establishment from persistence.

Developing a Theory-Based Simulation Educator Resource.

Science.gov (United States)

Thomas, Christine M; Sievers, Lisa D; Kellgren, Molly; Manning, Sara J; Rojas, Deborah E; Gamblian, Vivian C

2015-01-01

The NLN Leadership Development Program for Simulation Educators 2014 faculty development group identified a lack of a common language/terminology to outline the progression of expertise of simulation educators. The group analyzed Benner's novice-to-expert model and applied its levels of experience to simulation educator growth. It established common operational categories of faculty development and used them to organize resources that support progression toward expertise. The resulting theory-based Simulator Educator Toolkit outlines levels of ability and provides quality resources to meet the diverse needs of simulation educators and team members.

Development of HANARO engineering simulator (I)

International Nuclear Information System (INIS)

Jung, Hoan Sung; Han, G. Y.; Kim, M. J.; Kim, Y. K.; Lee, K. H.; Park, S. J.; Kim, H. K.; Park, J. H.

2001-01-01

The simulation models for HANARO have been developed. Core dynamics is modeled by two-point kinetics. Thermal-hydraulic characteristics are also modeled for the primary, secondary, and reflector cooling systems. Control algorithms used in the digital controller are modeled to control the reactor in same manner with the real system. Prototype simulator was implemented to test developed models. The computer system for distributed simulation was prepared

Development and Characterization of Boehmite Component Simulant

Energy Technology Data Exchange (ETDEWEB)

Russell, Renee L.; Peterson, Reid A.; Smith, Harry D.; Rinehart, Donald E.; Aker, Pamela M.; Buck, Edgar C.

2009-03-10

According to Bechtel National Inc.’s (BNI’s) Test Specification 24590-PTF-TSP-RT-06-006, Rev 0, “Simulant Development to Support the Development and Demonstration of Leaching and Ultrafiltration Pretreatment Processes,” simulants for boehmite, gibbsite, and filtration are to be developed that can be used in subsequent bench and integrated testing of the leaching/filtration processes. These simulants will then be used to demonstrate the leaching process and to help refine processing conditions that may impact safety basis considerations (Smith 2006). This report documents the results of the boehmite simulant development.

Numerical Simulation and Experimental Validation of an Integrated Sleeve-Wedge Anchorage for CFRP Rods

DEFF Research Database (Denmark)

Schmidt, Jacob Wittrup; Smith, Scott T.; Täljsten, Björn

2011-01-01

. Recently, an integrated sleeve-wedge anchorage has been successfully developed specifically for CFRP rods. This paper in turn presents a numerical simulation of the newly developed anchorage using ABAQUS. The three-dimensional finite element (FE) model, which considers material non-linearity, uses...

Module-based Simulation System for efficient development of nuclear simulation programs

International Nuclear Information System (INIS)

Yoshikawa, Hidekazu; Wakabayashi, Jiro

1990-01-01

Module-based Simulation System (MSS) has been developed to realize a new software environment enabling versatile dynamic simulation of a complex nuclear power plant system flexibly. Described in the paper are (i) fundamental methods utilized in MMS and its software systemization, (ii) development of human interface system to help users in generating integrated simulation programs automatically, and (iii) development of an intelligent user support system for helping users in the two phases of automatical semantic diagnosis and consultation to automatic input data setup for the MSS-generated programs. (author)

The effectiveness of newly developed written asthma action plan in improvement of asthma outcome in children.

Science.gov (United States)

Lakupoch, Kingthong; Manuyakorn, Wiparat; Preutthipan, Aroonwan; Kamalaporn, Harutai

2017-09-17

Providing asthma education about controller medication use and appropriate management of asthma exacerbation are the keys to improving the disease outcome. Many asthma guidelines recommend that physicians provide written asthma action plan (WAAP) to all of their asthmatic patients. However, the benefit of WAAP is unclear. Thus, we have created a new WAAP which is simplified in Thai and more user friendly. To determine the effectiveness of the newly developed asthma action plan in management of children with asthma. Asthmatic children who meet inclusion criteria all received the WAAP and they were followed up for 6 months with measurement of outcome variables, such as asthma exacerbation that required emergency room visit, unscheduled OPD visit, admission and school absence in order to compare with the past 6 months before receiving the WAAP. The analyzed outcomes of forty-nine children show significantly reduced emergency room visit (P-value 0.005), unscheduled OPD visit (P-value 0.046), admission days (P-value 0.026) and school absence days (P-value 0.022). Well controlled group and mild severity group were not the factors that contribute to decreased emergency room visit but step up therapy may be the co-factor to decreased ER visit. The results of this study suggest that the provision of newly developed WAAP is useful for improving self-care of asthma patients and reducing asthma exacerbation.

Development and Characterization of Gibbsite Component Simulant

International Nuclear Information System (INIS)

Russell, Renee L.; Smith, Harry D.; Rinehart, Donald E.; Peterson, Reid A.

2009-01-01

According to Bechtel National, Inc.'s (BNI's) Test Specification 24590-PTF-TSP-RT-06-006,, 'Simulant Development to Support the Development and Demonstration of Leaching and Ultrafiltration Pretreatment Processes', simulants for boehmite, gibbsite, and filtration are to be developed so they can be used in subsequent bench and integrated testing of the leaching/filtration processes for the River Protection Project-Waste Treatment and Immobilization Plant (RPP-WTP). These simulants will then be used to demonstrate the leaching process and to help refine processing conditions that may impact safety basis considerations (Smith 2006). This report documents PNNL's results of the gibbsite simulant development.

Fluid-structure interaction computations for geometrically resolved rotor simulations using CFD

DEFF Research Database (Denmark)

Heinz, Joachim Christian; Sørensen, Niels N.; Zahle, Frederik

2016-01-01

fluid dynamics (CFD) solver EllipSys3D. The paper shows that the implemented loose coupling scheme, despite a non-conservative force transfer, maintains a sufficient numerical stability and a second-order time accuracy. The use of a strong coupling is found to be redundant. In a first test case......This paper presents a newly developed high-fidelity fluid–structure interaction simulation tool for geometrically resolved rotor simulations of wind turbines. The tool consists of a partitioned coupling between the structural part of the aero-elastic solver HAWC2 and the finite volume computational......, the newly developed coupling between HAWC2 and EllipSys3D (HAWC2CFD) is utilized to compute the aero-elastic response of the NREL 5-MW reference wind turbine (RWT) under normal operational conditions. A comparison with the low-fidelity but state-of-the-art aero-elastic solver HAWC2 reveals a very good...

The Simulator Development for RDE Reactor

Science.gov (United States)

Subekti, Muhammad; Bakhri, Syaiful; Sunaryo, Geni Rina

2018-02-01

BATAN is proposing the construction of experimental power reactor (RDE reactor) for increasing the public acceptance on NPP development plan, proofing the safety level of the most advanced reactor by performing safety demonstration on the accidents such as Chernobyl and Fukushima, and owning the generation fourth (G4) reactor technology. For owning the reactor technology, the one of research activities is RDE’s simulator development that employing standard equation. The development utilizes standard point kinetic and thermal equation. The examination of the simulator carried out comparison in which the simulation’s calculation result has good agreement with assumed parameters and ChemCAD calculation results. The transient simulation describes the characteristic of the simulator to respond the variation of power increase of 1.5%/min, 2.5%/min, and 3.5%/min.

Development and Characterization of Gibbsite Component Simulant

Energy Technology Data Exchange (ETDEWEB)

Russell, Renee L.; Smith, Harry D.; Rinehart, Donald E.; Peterson, Reid A.

2009-01-29

According to Bechtel National, Inc.’s (BNI’s) Test Specification 24590-PTF-TSP-RT-06-006, Rev 0, "Simulant Development to Support the Development and Demonstration of Leaching and Ultrafiltration Pretreatment Processes," simulants for boehmite, gibbsite, and filtration are to be developed so they can be used in subsequent bench and integrated testing of the leaching/filtration processes for the River Protection Project-Waste Treatment and Immobilization Plant (RPP-WTP). These simulants will then be used to demonstrate the leaching process and to help refine processing conditions that may impact safety basis considerations (Smith 2006). This report documents PNNL’s results of the gibbsite simulant development.

Track Simulation and Reconstruction in the ATLAS experiment

CERN Document Server

Salzburger, Andreas; Elsing, Markus

The reconstruction and simulation of particle trajectories is an inevitable part of the analysis strate- gies for data taken with the ATLAS detector. Many aspects and necessary parts of a high-quality track reconstruction will be presented and discussed in this work. At first, the technical realisation of the data model and the reconstruction geometry will be given; the reconstruction geometry is charac- terised by a newly developed navigation model and an automated procedure for the synchronisation of the detailed simulation geometry description with the simplified reconstruction geometry model, which allows a precise description of the tracker material in track reconstruction. Both components help the coherent and fast integration of material effects in a newly established track extrapolation package, that is discussed in the following. The extrapolation engine enables a highly precise trans- port of the track parameterisation and the associated covariances through the complex magnetic field and the detec...

Conventional and improved cytotoxicity test methods of newly developed biodegradable magnesium alloys

Science.gov (United States)

Han, Hyung-Seop; Kim, Hee-Kyoung; Kim, Yu-Chan; Seok, Hyun-Kwang; Kim, Young-Yul

2015-11-01

Unique biodegradable property of magnesium has spawned countless studies to develop ideal biodegradable orthopedic implant materials in the last decade. However, due to the rapid pH change and extensive amount of hydrogen gas generated during biocorrosion, it is extremely difficult to determine the accurate cytotoxicity of newly developed magnesium alloys using the existing methods. Herein, we report a new method to accurately determine the cytotoxicity of magnesium alloys with varying corrosion rate while taking in-vivo condition into the consideration. For conventional method, extract quantities of each metal ion were determined using ICP-MS and the result showed that the cytotoxicity due to pH change caused by corrosion affected the cell viability rather than the intrinsic cytotoxicity of magnesium alloy. In physiological environment, pH is regulated and adjusted within normal pH (˜7.4) range by homeostasis. Two new methods using pH buffered extracts were proposed and performed to show that environmental buffering effect of pH, dilution of the extract, and the regulation of eluate surface area must be taken into consideration for accurate cytotoxicity measurement of biodegradable magnesium alloys.

Visualization needs and techniques for astrophysical simulations

International Nuclear Information System (INIS)

Kapferer, W; Riser, T

2008-01-01

Numerical simulations have evolved continuously towards being an important field in astrophysics, equivalent to theory and observation. Due to the enormous developments in computer sciences, both hardware- and software-architecture, state-of-the-art simulations produce huge amounts of raw data with increasing complexity. In this paper some aspects of problems in the field of visualization in numerical astrophysics in combination with possible solutions are given. Commonly used visualization packages along with a newly developed approach to real-time visualization, incorporating shader programming to uncover the computational power of modern graphics cards, are presented. With these techniques at hand, real-time visualizations help scientists to understand the coherences in the results of their numerical simulations. Furthermore a fundamental problem in data analysis, i.e. coverage of metadata on how a visualization was created, is highlighted.

A comparison of three approaches for simulating fine-scale surface winds in support of wildland fire management: Part I. Model formulation and comparison against measurements

Science.gov (United States)

Jason M. Forthofer; Bret W. Butler; Natalie S. Wagenbrenner

2014-01-01

For this study three types of wind models have been defined for simulating surface wind flow in support of wildland fire management: (1) a uniform wind field (typically acquired from coarse-resolution (,4 km) weather service forecast models); (2) a newly developed mass-conserving model and (3) a newly developed mass and momentumconserving model (referred to as the...

Combustion, performance and emissions characteristics of a newly ...

Indian Academy of Sciences (India)

of a newly developed CRDI single cylinder diesel engine. AVINASH ... In case of unit injector and unit pump systems, fuel injection pressure depends on ... nozzle hole diameters were effective in reducing smoke and PM emissions. However ...

SIMULATION GAMING FOR MANAGEMENT DEVELOPMENT.

Science.gov (United States)

MCKENNEY, JAMES L.

THE PRESENT HARVARD BUSINESS SCHOOL MANAGEMENT SIMULATION GAME WAS DEVELOPED AS A TEACHING DEVICE FOR CLASSES OF 20 OR MORE STUDENTS GROUPED INTO FOUR- AND FIVE-MAN TEAMS CALLED "FIRMS." EACH FIRM COMPETES WITH OTHERS IN AN "INDUSTRY," AN ECONOMIC ABSTRACTION OF A CONSUMER GOODS MARKET PROGRAMED TO BE SIMULATED ON AN ELECTRONIC…

The use of newly developed real-time PCR for the rapid identification of bacteria in culture-negative osteomyelitis.

Science.gov (United States)

Kobayashi, Naomi; Bauer, Thomas W; Sakai, Hiroshige; Togawa, Daisuke; Lieberman, Isador H; Fujishiro, Takaaki; Procop, Gary W

2006-12-01

We report a case of a culture-negative osteomyelitis in which our newly developed real-time polymerase chain reaction (PCR) could differentiate Staphylococcus aureus from Staphylococcus epidermidis. This is the first report that described the application of this novel assay to an orthopedics clinical sample. This assay may be useful for other clinical culture-negative cases in a combination with a broad-spectrum assay as a rapid microorganism identification method.

Perceptions of the clinical competence of newly registered nurses in the North West province

Directory of Open Access Journals (Sweden)

M.R. Moeti

2004-09-01

Full Text Available The clinical competence of newly registered nurses relating to the care of individual Clients, depends on their ability to correlate theoretical knowledge learned in the classroom with practice and the development of clinical skills. Its foundation lies in the ability to identify and solve problems that emanate from critical thinking, analytical reasoning and reflective practice. It is clear that the quality of clinical exposure plays a leading role in the development of nursing professionals. Nursing skills alone cannot ensure quality care of clients without the application of theory. Facilitation of this theory to practice therefore remains an essential component of nursing education. This study was aimed at identifying areas of incompetence of newly registered nurses (1998- 2001 in the clinical area by determining the newly registered nurses1 and professional nurses1 perceptions of the competence of the newly registered nurses. A quantitative, non-experimental, descriptive survey was used to collect the data regarding the clinical competence of newly registered nurses (1998-2001.

Developing the Simulator Instructor’s Pedagogical Competence

DEFF Research Database (Denmark)

Sjøstedt, Peter

2014-01-01

The full benefits of investment in simulator-based training are achieved only when development of the simulator instructor’s pedagogical competence accompanies the acquisition of advanced technology. In spite of this, the instructor’s pedagogical competence often is not well developed. Courses...... for simulator instructors that address their experiential instructional skills and their understanding of adult participants' learning processes are rare. Lessons learned about the instructor’s role that focus on the relationship between instruction and learning are seldom reported. Simulator instructors......’ pedagogical competence appears to be an area afforded insufficient attention from the simulation community. Based on lessons learned from our four-day pedagogical course for naval simulator instructors in the Danish armed forces, this paper presents a framework for instructors’ pedagogical competence...

Measurement equivalence of the newly developed Quality of Life in Childhood Epilepsy Questionnaire (QOLCE-55).

Science.gov (United States)

Ferro, Mark A; Goodwin, Shane W; Sabaz, Mark; Speechley, Kathy N

2016-03-01

The aim of this study was to examine measurement equivalence of the newly developed Quality of Life in Childhood Epilepsy Questionnaire (QOLCE-55) across age, sex, and time in a representative sample of children with newly diagnosed epilepsy. Data come from 373 children enrolled in the Health-related Quality of Life in Children with Epilepsy Study (HERQULES), a multisite prospective cohort study. Measurement equivalence was examined using a multiple-group confirmatory factor analysis framework, whereby increasingly stringent parameter constraints are imposed on the model. Comparison groups were stratified based on age (4-7 years vs. 8-12 years), sex (male vs. female), and time (measurement of health-related quality of life at diagnosis vs. 24 months later). The QOLCE-55 demonstrated measurement equivalence at the level of strict invariance for each model tested--age: χ(2) (3,123) = 4,097.3, p QOLCE-55 are perceived similarly among groups stratified by age, sex, and time and provide further evidence supporting the validity of the scale in children with epilepsy. Health professionals and researchers should be confident that group comparisons made using the QOLCE-55 are unbiased and that any group differences detected are meaningful; that is, not related to differences in the interpretation of items by informants. Future research replicating these findings is encouraged. Wiley Periodicals, Inc. © 2016 International League Against Epilepsy.

OpenMP-accelerated SWAT simulation using Intel C and FORTRAN compilers: Development and benchmark

Science.gov (United States)

Ki, Seo Jin; Sugimura, Tak; Kim, Albert S.

2015-02-01

We developed a practical method to accelerate execution of Soil and Water Assessment Tool (SWAT) using open (free) computational resources. The SWAT source code (rev 622) was recompiled using a non-commercial Intel FORTRAN compiler in Ubuntu 12.04 LTS Linux platform, and newly named iOMP-SWAT in this study. GNU utilities of make, gprof, and diff were used to develop the iOMP-SWAT package, profile memory usage, and check identicalness of parallel and serial simulations. Among 302 SWAT subroutines, the slowest routines were identified using GNU gprof, and later modified using Open Multiple Processing (OpenMP) library in an 8-core shared memory system. In addition, a C wrapping function was used to rapidly set large arrays to zero by cross compiling with the original SWAT FORTRAN package. A universal speedup ratio of 2.3 was achieved using input data sets of a large number of hydrological response units. As we specifically focus on acceleration of a single SWAT run, the use of iOMP-SWAT for parameter calibrations will significantly improve the performance of SWAT optimization.

Newly qualified teachers´ possibilities to get foothold in a lifelong career course

DEFF Research Database (Denmark)

Krøjgaard, Frede; Frederiksen, Lisbeth Angela Lunde

Keyword: Induction program, newly qualified teachers, NQT, retention, professional development In Contrary to many other countries in Europe Denmark does not have any kind of national program regarding teacher induction program (TIP) or support in general to newly qualified teachers what so ever...

The practical skills of newly qualified nurses.

Science.gov (United States)

Danbjørg, Dorthe Boe; Birkelund, Regner

2011-02-01

This paper reports the findings from a study of newly qualified nurses and which subjects the nurses regarded as the most important in order to be able to live up to the requirements of clinical practice, and how they experience their potential for developing practical and moral skills, after the decrease in practical training. A qualitative approach guided the research process and the analysis of the data. The data was collected by participant observation and qualitative interviews with four nurses as informants. The conclusions made in this study are based on the statements and the observations of the newly qualified nurses. Our findings are discussed in relation to the Aristotelian concept and other relevant literature. The main message is that the newly qualified nurses did not feel equipped when they finished their training. This could be interpreted as a direct consequence of the decrease in practical training. Our study also underlines that the way nursing theory is perceived and taught is problematic. The interviews revealed that the nurses think that nursing theories should be applied directly in practice. This misunderstanding is probably also applicable to the teachers of the theories. Copyright © 2010 Elsevier Ltd. All rights reserved.

Comparison of newly developed anti-bone morphogenetic protein 4 llama-derived antibodies with commercially available BMP4 inhibitors.

Science.gov (United States)

Calpe, Silvia; Correia, Ana C P; Sancho-Serra, Maria Del Carmen; Krishnadath, Kausilia K

2016-01-01

Due to improved understanding of the role of bone morphogenetic protein 4 (BMP4) in an increasing number of diseases, the development of selective inhibitors of BMP4 is an attractive therapeutic option. The currently available BMP4 inhibitors are not suitable as therapeutics because of their low specificity and low effectiveness. Here, we compared newly generated anti-BMP4 llama-derived antibodies (VHHs) with 3 different types of commercially available BMP4 inhibitors, natural antagonists, small molecule BMPR inhibitors and conventional anti-BMP4 monoclonal antibodies. We found that the anti-BMP4 VHHs were as effective as the natural antagonist or small molecule inhibitors, but had higher specificity. We also showed that commercial anti-BMP4 antibodies were inferior in terms of both specificity and effectiveness. These findings might result from the fact that the VHHs C4C4 and C8C8 target a small region within the BMPR1 epitope of BMP4, whereas the commercial antibodies target other areas of the BMP4 molecule. Our results show that the newly developed anti-BMP4 VHHs are promising antibodies with better specificity and effectivity for inhibition of BMP4, making them an attractive tool for research and for therapeutic applications.

GEM simulation methods development

International Nuclear Information System (INIS)

Tikhonov, V.; Veenhof, R.

2002-01-01

A review of methods used in the simulation of processes in gas electron multipliers (GEMs) and in the accurate calculation of detector characteristics is presented. Such detector characteristics as effective gas gain, transparency, charge collection and losses have been calculated and optimized for a number of GEM geometries and compared with experiment. A method and a new special program for calculations of detector macro-characteristics such as signal response in a real detector readout structure, and spatial and time resolution of detectors have been developed and used for detector optimization. A detailed development of signal induction on readout electrodes and electronics characteristics are included in the new program. A method for the simulation of charging-up effects in GEM detectors is described. All methods show good agreement with experiment

Development of a framework for identification of political environmental issues faced by multinational hotel chains in newly industrialized countries in Asia

OpenAIRE

Kim, Chol Yong

1992-01-01

The primary/objective of this study was to develop a framework for identification of political environmental issues faced by multinational hotel chains in newly industrialized countries in Asia. To accomplish the objective, key factors having an impact upon these hotel chains were identified using the Delphi Technique.

Development of SMATER Virtual Reality Simulator

Energy Technology Data Exchange (ETDEWEB)

Chung, Byoung Ha; Chung, B. H.; You, H. Y.; Kim, Y. M.; Park, J. B.; Choi, I. S.; Won, T. W.; Bae, J. B.; Kang, H. K.; Jang, J. M.; Heo, J. W.; Park, M. Y.; Kyun, H. S.; Lee, C. J. [Post Media Ltd., Taejon (Korea, Republic of)

1997-11-01

In this research task, we want to develop the most suitable design of Spent Fuel Management Facility and develop 3D simulator for our illustration by applying method as such as graphics, simulation, kinematics, dynamics, and collision detection in virtual reality. Through this, we set the capability of making verification on modifying existing conceptual design as our final objective. 6 tabs., 35 figs. (author)

Molecular Dynamics Simulation Studies of Caffeine Aggregation in Aqueous Solution

OpenAIRE

Tavagnacco, Letizia; Schnupf, Udo; Mason, Philip E.; Saboungi, Marie-Louise; Cesàro, Attilio; Brady, John W.

2011-01-01

Molecular dynamics simulations were carried out on a system of eight independent caffeine molecules in a periodic box of water at 300 K, representing a solution near the solubility limit for caffeine at room temperature, using a newly-developed CHARMM-type force field for caffeine in water. Simulations were also conducted for single caffeine molecules in water using two different water models (TIP3P and TIP4P). Water was found to structure in a complex fashion around the planar caffeine molec...

Numerical simulation of thermal radiation from smoking flames; Numerische Simulation der Waermestrahlung von russenden Flammen

Energy Technology Data Exchange (ETDEWEB)

Koch, T. [Duisburg Univ. (Gesamthochschule) (Germany). Lehrstuhl fuer Technische Chemie; Staus, S. [Duisburg Univ. (Gesamthochschule) (Germany). Lehrstuhl fuer Technische Chemie; Schoenbucher, A. [Duisburg Univ. (Gesamthochschule) (Germany). Lehrstuhl fuer Technische Chemie

1997-08-01

After presenting the most common semi-empirical simulation model, the authors describe the newly developed field model and its modules with their mathematical and physical fundamentals. First results are presented for the calculation of a diffusion flame. (orig./GL) [Deutsch] In der vorliegenden Arbeit wird, nach einer Darstellung der gebraeuchlichen halbempirischen Simulationsmodelle, das entwickelte Feldmodell beschrieben und seine einzelnen Module mit ihren mathematischen und physikalischen Grundlagen vorgestellt. Im Anschluss werden erste Ergebnisse fuer die Berechnung einer Diffusionsflamme aufgezeigt. (orig./GL)

Developing, implementing and evaluating a simulation learning ...

African Journals Online (AJOL)

Hafaza Bibi Amod

Research significance: To develop a simulation learning package that uses high fidelity simulation to ... common cause of maternal mortality in South Africa and ... Framework cited by Jeffries (2007). ... nario development toolkits and various best practice guide- ..... analysis in nursing research: Concepts, procedures, and.

Development of intelligent simulations at LLNL

Energy Technology Data Exchange (ETDEWEB)

Cunningham, C.T.

1994-03-01

The Virtual Commander Project (VCom) is developing a capability for semiautomated optimal control of simulation entities. Properties of our control paradigm are goal-directed planning, hierarchical plan generation, automated fault detection, adaptive plan repair, and optimized cooperation and coordination among units, in addition to more conventional rule-driven behaviors. VCom has been applied to planning armor engagements at the battalion level and below. We are currently investigating movement-to-contact and fire-and-movement maneuvers. These capabilities will be demonstrated in April in conjunction with the Joint Conflict Model (JCM) a large, entity-level, constructive combat simulation. Both simulations have been developed to interoperate in a distributed computing environment using Distributed Interactive Simulation (DIS) protocols. Prototype applications have been demonstrated in other civilian and military contexts. A focus of our current work is the rapid prototyping of such applications.

An Object-Oriented Serial DSMC Simulation Package

Science.gov (United States)

Liu, Hongli; Cai, Chunpei

2011-05-01

A newly developed three-dimensional direct simulation Monte Carlo (DSMC) simulation package, named GRASP ("Generalized Rarefied gAs Simulation Package"), is reported in this paper. This package utilizes the concept of simulation engine, many C++ features and software design patterns. The package has an open architecture which can benefit further development and maintenance of the code. In order to reduce the engineering time for three-dimensional models, a hybrid grid scheme, combined with a flexible data structure compiled by C++ language, are implemented in this package. This scheme utilizes a local data structure based on the computational cell to achieve high performance on workstation processors. This data structure allows the DSMC algorithm to be very efficiently parallelized with domain decomposition and it provides much flexibility in terms of grid types. This package can utilize traditional structured, unstructured or hybrid grids within the framework of a single code to model arbitrarily complex geometries and to simulate rarefied gas flows. Benchmark test cases indicate that this package has satisfactory accuracy for complex rarefied gas flows.

Supplemental branched-chain amino acids improve performance and immune response of newly-received feedlot calves

Science.gov (United States)

Supplemental branched-chain AA (BCAA) improved N balance of steers during a simulated pathogen challenge. The objective of this study was to determine the effect of supplemental BCAA on growth and health of newly-received feedlot steers. Steers (n = 120; initial BW = 376 ± 5 kg) were blocked by BW a...

Experimental investigation for determination of optimal X-ray beam tube voltages in a newly developed digital breast tomosynthesis system

Energy Technology Data Exchange (ETDEWEB)

Park, Hye-Suk, E-mail: radiosugar@yonsei.ac.kr [Department of Radiological Science and Research Institute of Health Science, Yonsei University, Wonju, Gangwon 220-710 (Korea, Republic of); Kim, Ye-Seul, E-mail: radiohesugar@gmail.com [Department of Radiological Science and Research Institute of Health Science, Yonsei University, Wonju, Gangwon 220-710 (Korea, Republic of); Choi, Young-Wook, E-mail: ywchoi@keri.re.kr [Korea Electrotechnology Research Institute (KERI), Ansan, Geongki 426-170 (Korea, Republic of); Choi, JaeGu, E-mail: jgchoi88@paran.com [Korea Electrotechnology Research Institute (KERI), Ansan, Geongki 426-170 (Korea, Republic of); Rhee, Yong-Chun, E-mail: ycrhee@yonsei.ac.kr [Department of Radiological Science and Research Institute of Health Science, Yonsei University, Wonju, Gangwon 220-710 (Korea, Republic of); Kim, Hee-Joung, E-mail: hjk1@yonsei.ac.kr [Department of Radiological Science and Research Institute of Health Science, Yonsei University, Wonju, Gangwon 220-710 (Korea, Republic of)

2014-11-01

Our purpose was to investigate optimal tube voltages (kVp) for a newly developed digital breast tomosynthesis (DBT) process and to determine tube current–exposure time products (mA s) for the average glandular dose (AGD), which is similar to that of the two views in conventional mammography (CM). In addition, the optimal acquisition parameters for this system were compared with those of CM. The analysis was based on the contrast-to-noise ratio (CNR) from the simulated micro-calcifications on homogeneous phantoms, and the figure of merit (FOM) was retrieved from the CNR and AGD at X-ray tube voltages ranging from 24 to 40 kVp at intervals of 2 kV. The optimal kVp increased more than 2 kV with increasing glandularity for thicker (≥50 mm) breast phantoms. The optimal kVp for DBT was found to be 4–7 kV higher than that calculated for CM with breast phantoms thicker than 50 mm. This is likely due to the greater effect of noise and dose reduction by kVp increment when using the lower dose per projection in DBT. It is important to determine optimum acquisition conditions for a maximally effective DBT system. The results of our study provide useful information to further improve DBT for high quality imaging.

A Network Contention Model for the Extreme-scale Simulator

Energy Technology Data Exchange (ETDEWEB)

Engelmann, Christian [ORNL; Naughton III, Thomas J [ORNL

2015-01-01

The Extreme-scale Simulator (xSim) is a performance investigation toolkit for high-performance computing (HPC) hardware/software co-design. It permits running a HPC application with millions of concurrent execution threads, while observing its performance in a simulated extreme-scale system. This paper details a newly developed network modeling feature for xSim, eliminating the shortcomings of the existing network modeling capabilities. The approach takes a different path for implementing network contention and bandwidth capacity modeling using a less synchronous and accurate enough model design. With the new network modeling feature, xSim is able to simulate on-chip and on-node networks with reasonable accuracy and overheads.

Newly graduated nurses' use of knowledge sources

DEFF Research Database (Denmark)

Voldbjerg, Siri Lygum; Grønkjaer, Mette; Sørensen, Erik Elgaard

2016-01-01

AIM: To advance evidence on newly graduated nurses' use of knowledge sources. BACKGROUND: Clinical decisions need to be evidence-based and understanding the knowledge sources that newly graduated nurses use will inform both education and practice. Qualitative studies on newly graduated nurses' use...... underscoring progression in knowledge use and perception of competence and confidence among newly graduated nurses. CONCLUSION: The transition phase, feeling of confidence and ability to use critical thinking and reflection, has a great impact on knowledge sources incorporated in clinical decisions....... The synthesis accentuates that for use of newly graduated nurses' qualifications and skills in evidence-based practice, clinical practice needs to provide a supportive environment which nurtures critical thinking and questions and articulates use of multiple knowledge sources....

Being a team leader: newly registered nurses relate their experiences.

Science.gov (United States)

Ekström, Louise; Idvall, Ewa

2015-01-01

This paper presents a study that explores how newly qualified registered nurses experience their leadership role in the ward-based nursing care team. A nurse's clinical leadership affects the quality of care provided. Newly qualified nurses experience difficulties during the transition period from student to qualified professional and find it challenging to lead nursing care. Twelve nurses were interviewed and the transcribed texts analysed using qualitative content analysis to assess both manifest and latent content. Five themes were identified: feeling stranded; forming well-functioning teams; learning to lead; having the courage, strength, and desire to lead; and ensuring appropriate care. The findings indicate that many factors limit nurses' leadership but some circumstances are supportive. The leadership prerequisites for newly registered nurses need to improve, emphasizing different ways to create a supportive atmosphere that promotes professional development and job satisfaction. To increase nurse retention and promote quality of care, nurse managers need to clarify expectations and guide and support newly qualified nurses in a planned way. © 2013 John Wiley & Sons Ltd.

Development and Characterization of Boehmite Component Simulant

Energy Technology Data Exchange (ETDEWEB)

Russell, Renee L.; Peterson, Reid A.; Smith, Harry D.; Rinehart, Donald E.; Aker, Pamela M.; Buck, Edgar C.

2009-06-03

According to Bechtel National Inc.’s (BNI’s) Test Specification 24590-PTF-TSP-RT-06-006, Rev 0, “Simulant Development to Support the Development and Demonstration of Leaching and Ultrafiltration Pretreatment Processes,” simulants for boehmite, gibbsite, and filtration are to be developed that can be used in subsequent bench and integrated testing of the leaching/filtration processes. These simulants will then be used to demonstrate the leaching process and to help refine processing conditions that may impact safety basis considerations (Smith 2006). This report documents the results of the boehmite simulant development and blended simulant crossflow ultrafiltration leaching completed in accordance with the test plan TP-RPP-WTP-469 Rev 0 (WTP Doc. No. 24590- 101-TSA-W000-0004-182-00001 Rev 00A) prepared and approved in response to the cited test specification. This report also includes the results of the aluminate and anion effect on boehmite dissolution performed in accordance with the test plan TP-RPP-WTP-509, Rev 0 (WTP Doc. No. 24590-101-TSA-W000-0004-72-00019 Rev 00A) prepared and approved in response to the Test Specification 24590-WTP-TSP-RT-07-004, Rev 0 (Sundar 2007).

Open Source Power Plant Simulator Development Under Matlab Environment

International Nuclear Information System (INIS)

Ratemi, W.M.; Fadilah, S.M.; Abonoor, N

2008-01-01

In this paper an open source programming approach is targeted for the development of power plant simulator under Matlab environment. With this approach many individuals can contribute to the development of the simulator by developing different orders of complexities of the power plant components. Such modules can be modeled based on physical principles, or using neural networks or other methods. All of these modules are categorized in Matlab library, of which the user can select and build up his simulator. Many international companies developed its own authoring tool for the development of its simulators, and hence it became its own property available for high costs. Matlab is a general software developed by mathworks that can be used with its toolkits as the authoring tool for the development of components by different individuals, and through the appropriate coordination, different plant simulators, nuclear, traditional , or even research reactors can be computerly assembled. In this paper, power plant components such as a pressurizer, a reactor, a steam generator, a turbine, a condenser, a feedwater heater, a valve, a pump are modeled based on physical principles. Also a prototype modeling of a reactor ( a scram case) based on neural networks is developed. These modules are inserted in two different Matlab libraries one called physical and the other is called neural. Furthermore, during the simulation one can pause and shuffle the modules selected from the two libraries and then proceed the simulation. Also, under the Matlab environment a PID controller is developed for multi-loop plant which can be integrated for the control of the appropriate developed simulator. This paper is an attempt to base the open source approach for the development of power plant simulators or even research reactor simulators. It then requires the coordination among interested individuals or institutions to set it to professionalism. (author)

Distributed co-simulation of embedded control software with exhaust gas recirculation water handling system using INTO-CPS

DEFF Research Database (Denmark)

Pedersen, Nicolai; Lausdahl, Kenneth; Sanchez, Enrique Vidal

2017-01-01

to reduce the overall costs of validation. This paper demonstrates how this can be achieved for a commercial system developed by MAN Diesel & Turbo using a newly developed tool chain based on the Functional Mock-up Interface standard for co-simulation supporting different operating systems. The generality...

Hydrocarbon Degradation in Caspian Sea Sediment Cores Subjected to Simulated Petroleum Seepage in a Newly Designed Sediment-Oil-Flow-Through System

Directory of Open Access Journals (Sweden)

Tina Treude

2017-04-01

Full Text Available The microbial community response to petroleum seepage was investigated in a whole round sediment core (16 cm length collected nearby natural hydrocarbon seepage structures in the Caspian Sea, using a newly developed Sediment-Oil-Flow-Through (SOFT system. Distinct redox zones established and migrated vertically in the core during the 190 days-long simulated petroleum seepage. Methanogenic petroleum degradation was indicated by an increase in methane concentration from 8 μM in an untreated core compared to 2300 μM in the lower sulfate-free zone of the SOFT core at the end of the experiment, accompanied by a respective decrease in the δ13C signal of methane from -33.7 to -49.5‰. The involvement of methanogens in petroleum degradation was further confirmed by methane production in enrichment cultures from SOFT sediment after the addition of hexadecane, methylnapthalene, toluene, and ethylbenzene. Petroleum degradation coupled to sulfate reduction was indicated by the increase of integrated sulfate reduction rates from 2.8 SO42-m-2 day-1 in untreated cores to 5.7 mmol SO42-m-2 day-1 in the SOFT core at the end of the experiment, accompanied by a respective accumulation of sulfide from 30 to 447 μM. Volatile hydrocarbons (C2–C6 n-alkanes passed through the methanogenic zone mostly unchanged and were depleted within the sulfate-reducing zone. The amount of heavier n-alkanes (C10–C38 decreased step-wise toward the top of the sediment core and a preferential degradation of shorter (C30 was seen during the seepage. This study illustrates, to the best of our knowledge, for the first time the development of methanogenic petroleum degradation and the succession of benthic microbial processes during petroleum passage in a whole round sediment core.

Hydrocarbon Degradation in Caspian Sea Sediment Cores Subjected to Simulated Petroleum Seepage in a Newly Designed Sediment-Oil-Flow-Through System.

Science.gov (United States)

Mishra, Sonakshi; Wefers, Peggy; Schmidt, Mark; Knittel, Katrin; Krüger, Martin; Stagars, Marion H; Treude, Tina

2017-01-01

The microbial community response to petroleum seepage was investigated in a whole round sediment core (16 cm length) collected nearby natural hydrocarbon seepage structures in the Caspian Sea, using a newly developed Sediment-Oil-Flow-Through (SOFT) system. Distinct redox zones established and migrated vertically in the core during the 190 days-long simulated petroleum seepage. Methanogenic petroleum degradation was indicated by an increase in methane concentration from 8 μM in an untreated core compared to 2300 μM in the lower sulfate-free zone of the SOFT core at the end of the experiment, accompanied by a respective decrease in the δ 13 C signal of methane from -33.7 to -49.5‰. The involvement of methanogens in petroleum degradation was further confirmed by methane production in enrichment cultures from SOFT sediment after the addition of hexadecane, methylnapthalene, toluene, and ethylbenzene. Petroleum degradation coupled to sulfate reduction was indicated by the increase of integrated sulfate reduction rates from 2.8 SO 4 2- m -2 day -1 in untreated cores to 5.7 mmol SO 4 2- m -2 day -1 in the SOFT core at the end of the experiment, accompanied by a respective accumulation of sulfide from 30 to 447 μM. Volatile hydrocarbons (C2-C6 n -alkanes) passed through the methanogenic zone mostly unchanged and were depleted within the sulfate-reducing zone. The amount of heavier n -alkanes (C10-C38) decreased step-wise toward the top of the sediment core and a preferential degradation of shorter (C30) was seen during the seepage. This study illustrates, to the best of our knowledge, for the first time the development of methanogenic petroleum degradation and the succession of benthic microbial processes during petroleum passage in a whole round sediment core.

Development of ODL in a Newly Industrialized Country according to Face-to-Face Contact, ICT, and E-Readiness

Directory of Open Access Journals (Sweden)

J. Marinda van Zyl

2013-03-01

Full Text Available A large number of unqualified and under-qualified in-service teachers are holding back socio-economical development in South Africa, a newly industrialized country. Open and distance learning (ODL provides an innovative strategy and praxis for developing and newly industrialized countries to reach their educational and socio-economical objectives through professional development and training. In order to examine factors which affect the success of ODL offered by the North-West University in South Africa, a qualitative and quantitative research approach is used. Factors examined include face-to-face classroom contact, the implementation and use of ICTs, and e-readiness. The relationships between these factors are also discussed. A questionnaire was administered to 87 teacher-students in four Advanced Certificate in Education (ACE programs to collect quantitative data regarding aspects of their classes and the e-readiness of students. This data was qualitatively elaborated upon by three semi-structured, open-ended focus-group interviews. Besides descriptive statistics, Spearman’s rank-order correlations (r were determined between variables pertaining to negative feelings towards face-to-face classroom contact, ODL as students’ choice of delivery mode, and students’ positive attitude towards information and communication technology (ICT. Combined quantitative and qualitative findings were used to evaluate the effectiveness of contact classes as well as the e-readiness of students towards the attainment of ODL development Phase D. This phase refers to UNESCO’s description of ICT implementation, integration, and use. Relationships (Spearman’s rank-order correlations between ODL, as teacher-students’ choice of educational delivery mode, and aspects of their e-readiness suggest that the e-readiness of teacher-students is implicit to their choice of ODL as educational delivery mode for professional development.

Development of Active Learning with Simulations and Games

Science.gov (United States)

Zapalska, Alina; Brozik, Dallas; Rudd, Denis

2012-01-01

Educational games and simulations are excellent active learning tools that offer students hands-on experience. Little research is available on developing games and simulations and how teachers can be assisted in making their own games and simulations. In this context, the paper presents a multi-step process of how to develop games and simulations…

Erosion of newly developed CFCs and Be under disruption heat loads

Science.gov (United States)

Nakamura, K.; Akiba, M.; Araki, M.; Dairaku, M.; Sato, K.; Suzuki, S.; Yokoyama, K.; Linke, J.; Duwe, R.; Bolt, H.; Roedig, M.

1996-10-01

An evaluation of the erosion under disruption heat loads is very important to the lifetime prediction of divertor armour tiles of next fusion devices such as ITER. In particular, erosion data on CFCs (carbon fiber reinforced composites) and beryllium (Be) as the armour materials is urgently required in the ITER design. For CFCs, high heat flux experiments on the newly developed CFCs with high thermal conductivity have been performed under the heat flux of around 800-2000 MW/m 2 and the pulse length of 2-5 ms in JAERI electron beam irradiation systems (JEBIS). As a result, the weight losses of B 4C doped CFCs after heating were almost same to those of the non doped CFC up to 5 wt% boron content. For Be, we have carried out our first disruption experiments on S65/C grade Be specimens in the Juelich divertor test facility in hot cells (JUDITH) facility as a frame work of the J—EU collaboration. The heating conditions were heat loads of 1250-5000 MW/m 2 for 2-8 ms, and the heated area was 3 × 3 mm 2. As a result, the protuberances of the heated area of Be were observed under the lower heat flux.

Erosion of newly developed CFCs and Be under disruption heat loads

International Nuclear Information System (INIS)

Nakamura, K.; Duwe, R.; Bolt, H.; Roedig, M.

1996-01-01

An evaluation of the erosion under disruption heat loads is very important to the lifetime prediction of divertor armour tiles of next fusion devices such as ITER. In particular, erosion data on CFCs (carbon fiber reinforced composites) and beryllium (Be) as the armour materials is urgently required in the ITER design. For CFCs, high heat flux experiments on the newly developed CFCs with high thermal conductivity have been performed under the heat flux of around 800-2000 MW/m 2 and the pulse length of 2-5 ms in JAERI electron beam irradiation systems (JEBIS). As a result, the weight losses of B 4 C doped CFCs after heating were almost same to those of the non doped CFC up to 5 wt% boron content. For Be, we have carried out our first disruption experiments on S65/C grade Be specimens in the Juelich divertor test facility in hot cells (JUDITH) facility as a frame work of the J-EU collaboration. The heating conditions were heat loads of 1250-5000 MW/m 2 for 2-8 ms, and the heated area was 3 x 3 mm 2 . As a result, the protuberances of the heated area of Be were observed under the lower heat flux. (orig.)

NUMERICAL MODELLING OF THE SOIL BEHAVIOUR BY USING NEWLY DEVELOPED ADVANCED MATERIAL MODEL

Directory of Open Access Journals (Sweden)

Jan Veselý

2017-02-01

Full Text Available This paper describes a theoretical background, implementation and validation of the newly developed Jardine plastic hardening-softening model (JPHS model, which can be used for numerical modelling of the soils behaviour. Although the JPHS model is based on the elasto-plastic theory, like the Mohr-Coulomb model that is widely used in geotechnics, it contains some improvements, which removes the main disadvantages of the MC model. The presented model is coupled with an isotopically hardening and softening law, non-linear elastic stress-strain law, non-associated elasto-plastic material description and a cap yield surface. The validation of the model is done by comparing the numerical results with real measured data from the laboratory tests and by testing of the model on the real project of the tunnel excavation. The 3D numerical analysis is performed and the comparison between the JPHS, Mohr-Coulomb, Modified Cam-Clay, Hardening small strain model and monitoring in-situ data is done.

Simulation of ultra-relativistic electrons and positrons channeling in crystals with MBN Explorer

DEFF Research Database (Denmark)

Sushko, Gennady B.; Bezchastnov, Victor G.; Solov'yov, Ilia

2013-01-01

A newly developed code, implemented as a part of the MBN Explorer package (Solov'yov et al., 2012; http://www.mbnexplorer.com/, 2012) [1] and [2] to simulate trajectories of an ultra-relativistic projectile in a crystalline medium, is presented. The motion of a projectile is treated classically b...

Use case driven approach to develop simulation model for PCS of APR1400 simulator

International Nuclear Information System (INIS)

Dong Wook, Kim; Hong Soo, Kim; Hyeon Tae, Kang; Byung Hwan, Bae

2006-01-01

The full-scope simulator is being developed to evaluate specific design feature and to support the iterative design and validation in the Man-Machine Interface System (MMIS) design of Advanced Power Reactor (APR) 1400. The simulator consists of process model, control logic model, and MMI for the APR1400 as well as the Power Control System (PCS). In this paper, a use case driven approach is proposed to develop a simulation model for PCS. In this approach, a system is considered from the point of view of its users. User's view of the system is based on interactions with the system and the resultant responses. In use case driven approach, we initially consider the system as a black box and look at its interactions with the users. From these interactions, use cases of the system are identified. Then the system is modeled using these use cases as functions. Lower levels expand the functionalities of each of these use cases. Hence, starting from the topmost level view of the system, we proceeded down to the lowest level (the internal view of the system). The model of the system thus developed is use case driven. This paper will introduce the functionality of the PCS simulation model, including a requirement analysis based on use case and the validation result of development of PCS model. The PCS simulation model using use case will be first used during the full-scope simulator development for nuclear power plant and will be supplied to Shin-Kori 3 and 4 plant. The use case based simulation model development can be useful for the design and implementation of simulation models. (authors)

Use of newly developed standardized form for interpretation of high-resolution CT in screening for pneumoconiosis

International Nuclear Information System (INIS)

Julien, P.J.; Sider, L.; Silverman, J.M.; Dahlgren, J.; Harber, P.; Bunn, W.

1991-01-01

This paper reports that although the International Labour Office (ILO) standard for interpretation of the posteroanterior chest radiograph has been available for 10 years, there has been no attempt to standardize the high-resolution CT (HRTC) readings for screening of pneumoconiosis. An integrated respirator surveillance program for 87 workers exposed to inorganic dust was conducted. This program consisted of a detailed occupational exposure history, physical symptoms and signs, spirometry, chest radiography, and HRCT. Two groups of workers with known exposure were studied with HRCT. Group 1 had normal spirometry results and chest radiographs, and group 2 had abnormalities at spirometry or on chest radiographs. The HRCT scans were read independently of the clinical findings and chest radiographs. The HRCT scans were interpreted by using an ILO-based standard form developed by the authors for this project. With the newly developed HRCT form, individual descriptive abnormality localized severity, and overall rating systems have been developed and compared for inter- and intraobserver consistency

A molecular dynamics simulation code ISIS

International Nuclear Information System (INIS)

Kambayashi, Shaw

1992-06-01

Computer simulation based on the molecular dynamics (MD) method has become an important tool complementary to experiments and theoretical calculations in a wide range of scientific fields such as physics, chemistry, biology, and so on. In the MD method, the Newtonian equations-of-motion of classical particles are integrated numerically to reproduce a phase-space trajectory of the system. In the 1980's, several new techniques have been developed for simulation at constant-temperature and/or constant-pressure in convenient to compare result of computer simulation with experimental results. We first summarize the MD method for both microcanonical and canonical simulations. Then, we present and overview of a newly developed ISIS (Isokinetic Simulation of Soft-spheres) code and its performance on various computers including vector processors. The ISIS code has a capability to make a MD simulation under constant-temperature condition by using the isokinetic constraint method. The equations-of-motion is integrated by a very accurate fifth-order finite differential algorithm. The bookkeeping method is also utilized to reduce the computational time. Furthermore, the ISIS code is well adopted for vector processing: Speedup ratio ranged from 16 to 24 times is obtained on a VP2600/10 vector processor. (author)

Design and Realization of Avionics Integration Simulation System Based on RTX

Directory of Open Access Journals (Sweden)

Wang Liang

2016-01-01

Full Text Available Aircraft avionics system becoming more and more complicated, it is too hard to test and verify real avionics systems. A design and realization method of avionics integration simulation system based on RTX was brought forward to resolve the problem. In this simulation system, computer software and hardware resources were utilized entirely. All kinds of aircraft avionics system HIL (hardware-in-loop simulations can be implemented in this platform. The simulation method provided the technical foundation of testing and verifying real avionics system. The research has recorded valuable data using the newly-developed method. The experiment results prove that the avionics integration simulation system was used well in some helicopter avionics HIL simulation experiment. The simulation experiment results provided the necessary judgment foundation for the helicopter real avionics system verification.

Nuclear Application Programs Development and Integration for a Simulator

Energy Technology Data Exchange (ETDEWEB)

Park, Hyun-Joon; Lee, Tae-Woo [KEPCO Engineering and Construction Co., Deajeon (Korea, Republic of)

2016-10-15

KEPCO E and C participated in the NAPS (Nuclear Application Programs) development project for BNPP (Barakah Nuclear Power Plant) simulator. The 3KEY MASTER™ was adopted for this project, which is comprehensive simulation platform software developed by WSC (Western Services Corporation) for the development, and control of simulation software. The NAPS based on actual BNPP project was modified in order to meet specific requirements for nuclear power plant simulators. Considerations regarding software design for BNPP simulator and interfaces between the 3KM platform and application programs are discussed. The repeatability is one of functional requirements for nuclear power plant simulators. In order to migrate software from actual plants to simulators, software functions for storing and retrieving plant conditions and program variables should be implemented. In addition, software structures need to be redesigned to meet the repeatability, and source codes developed for actual plants would have to be optimized to reflect simulator’s characteristics as well. The synchronization is an important consideration to integrate external application programs into the 3KM simulator.

Distributed Photovoltaics in the Swedish Energy System. Model Development and Simulations

International Nuclear Information System (INIS)

Widen, Joakim

2009-06-01

Application of photovoltaics (PV) is increasing worldwide, mainly due to extensive subsidy schemes for introducing CO 2 -free power generation. A majority of newly installed systems are distributed small-scale systems located in distribution grids, often at residential customers. Recent developments suggest that such distributed PV generation (PV-DG) could gain more interest in Sweden in the near future. With prospects of decreasing module prices, an extensive integration could be possible. This licentiate thesis presents the first part of a PhD project with the aim to determine the potential for domestic PV-DG in Sweden. Two aspects are treated in detail in the thesis: (1) the ability of PV to match a local domestic power demand and (2) impacts of extensive integration of PV-DG on power flow in low-voltage (LV) distribution grids. To make realistic studies for high-latitude conditions, there is a need for representative demand and PV generation data. As there is a lack of detailed domestic load data in Sweden, a major part of the work has been devoted to development of a stochastic load model. Interdisciplinary studies of household activities were performed to get insight into how domestic electricity use is embedded in the structure of everyday life. It was found that time-use (TU) data, normally used in the social sciences, can be used to model domestic power demand. Both a conversion model for estimating power demand from empirical TU data and a stochastic Markov-chain model for generating synthetic activity patterns and power demand were developed and extensively validated against measurements. Importantly, a realistic model of domestic lighting demand from occupancy patterns and irradiation data was developed, that preserves the negative correlation between irradiation and lighting demand. The models provide a basis for load matching studies and power-flow simulations, but can be used for other purposes as well. Case studies of individual households showed

Distributed Photovoltaics in the Swedish Energy System. Model Development and Simulations

Energy Technology Data Exchange (ETDEWEB)

Widen, Joakim

2009-06-15

Application of photovoltaics (PV) is increasing worldwide, mainly due to extensive subsidy schemes for introducing CO{sub 2}-free power generation. A majority of newly installed systems are distributed small-scale systems located in distribution grids, often at residential customers. Recent developments suggest that such distributed PV generation (PV-DG) could gain more interest in Sweden in the near future. With prospects of decreasing module prices, an extensive integration could be possible. This licentiate thesis presents the first part of a PhD project with the aim to determine the potential for domestic PV-DG in Sweden. Two aspects are treated in detail in the thesis: (1) the ability of PV to match a local domestic power demand and (2) impacts of extensive integration of PV-DG on power flow in low-voltage (LV) distribution grids. To make realistic studies for high-latitude conditions, there is a need for representative demand and PV generation data. As there is a lack of detailed domestic load data in Sweden, a major part of the work has been devoted to development of a stochastic load model. Interdisciplinary studies of household activities were performed to get insight into how domestic electricity use is embedded in the structure of everyday life. It was found that time-use (TU) data, normally used in the social sciences, can be used to model domestic power demand. Both a conversion model for estimating power demand from empirical TU data and a stochastic Markov-chain model for generating synthetic activity patterns and power demand were developed and extensively validated against measurements. Importantly, a realistic model of domestic lighting demand from occupancy patterns and irradiation data was developed, that preserves the negative correlation between irradiation and lighting demand. The models provide a basis for load matching studies and power-flow simulations, but can be used for other purposes as well. Case studies of individual households

Development and operation of a real-time simulation at the NASA Ames Vertical Motion Simulator

Science.gov (United States)

Sweeney, Christopher; Sheppard, Shirin; Chetelat, Monique

1993-01-01

The Vertical Motion Simulator (VMS) facility at the NASA Ames Research Center combines the largest vertical motion capability in the world with a flexible real-time operating system allowing research to be conducted quickly and effectively. Due to the diverse nature of the aircraft simulated and the large number of simulations conducted annually, the challenge for the simulation engineer is to develop an accurate real-time simulation in a timely, efficient manner. The SimLab facility and the software tools necessary for an operating simulation will be discussed. Subsequent sections will describe the development process through operation of the simulation; this includes acceptance of the model, validation, integration and production phases.

Evaluating the Physiological and Perceptual Responses of Wearing a Newly Designed Cooling Vest for Construction Workers.

Science.gov (United States)

Zhao, Yijie; Yi, Wen; Chan, Albert P C; Wong, Francis K W; Yam, Michael C H

2017-08-01

Construction workers are subjected to heat stress because of the hot environment, physically demanding tasks, and/or personal protective equipment. A tailor-made cooling vest that protects construction workers from heat-related injuries was developed. The purpose of the study is to examine a newly designed cooling vest's effectiveness in alleviating physiological and perceptual strain in a hot and humid environment. Twelve male participants performed two trials, i.e., cooling vest (VEST) and control (CON) in a climatic chamber controlled at 37°C temperature, 60% relative humidity, 0.3 m/s air velocity, and 450 W/m2 solar radiation to simulate the summer working environment of construction sites. Two bouts of treadmill exercise intermitted with 30-minute passive recovery were designed to simulate the practical work-rest schedule of the construction industry. The cooling vest was used during the passive recovery period in the VEST condition, and the results were compared with that of no cooling vest in the CON condition. The results revealed that the newly designed cooling vest can significantly alleviate heat strain and improve thermal comfort, based on the decrease in body temperature, heart rate, and subjective perceptions (including perceived exertion, thermal, wetness, and comfort sensation) of the participants. It can also prolong work duration in the subsequent exercise. The cooling countermeasures proposed in this study will be able to provide an effective solution in situations that involve repeated bouts of outdoor construction work. © The Author 2017. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

Game development and simulation with unreal technology

CERN Document Server

Tavakkoli, Alireza

2015-01-01

Game Development and Simulation with Unreal Technology explores the use of Unreal Engine 4 (UE4) for the development of real-time digital interactive contents to be used in computerized games or simulations. The engine is considered in three main iterations: from the basic use of the engine to build games and simulation content out of the box, to intermediate design of interactive content by building on the pre-supplied contents from the base engine, and through advanced implementations geared toward a comprehensive understanding of the power of the Unreal Engine. This is one of the first book

PCTFPeval: a web tool for benchmarking newly developed algorithms for predicting cooperative transcription factor pairs in yeast.

Science.gov (United States)

Lai, Fu-Jou; Chang, Hong-Tsun; Wu, Wei-Sheng

2015-01-01

Computational identification of cooperative transcription factor (TF) pairs helps understand the combinatorial regulation of gene expression in eukaryotic cells. Many advanced algorithms have been proposed to predict cooperative TF pairs in yeast. However, it is still difficult to conduct a comprehensive and objective performance comparison of different algorithms because of lacking sufficient performance indices and adequate overall performance scores. To solve this problem, in our previous study (published in BMC Systems Biology 2014), we adopted/proposed eight performance indices and designed two overall performance scores to compare the performance of 14 existing algorithms for predicting cooperative TF pairs in yeast. Most importantly, our performance comparison framework can be applied to comprehensively and objectively evaluate the performance of a newly developed algorithm. However, to use our framework, researchers have to put a lot of effort to construct it first. To save researchers time and effort, here we develop a web tool to implement our performance comparison framework, featuring fast data processing, a comprehensive performance comparison and an easy-to-use web interface. The developed tool is called PCTFPeval (Predicted Cooperative TF Pair evaluator), written in PHP and Python programming languages. The friendly web interface allows users to input a list of predicted cooperative TF pairs from their algorithm and select (i) the compared algorithms among the 15 existing algorithms, (ii) the performance indices among the eight existing indices, and (iii) the overall performance scores from two possible choices. The comprehensive performance comparison results are then generated in tens of seconds and shown as both bar charts and tables. The original comparison results of each compared algorithm and each selected performance index can be downloaded as text files for further analyses. Allowing users to select eight existing performance indices and 15

Motion simulation of hydraulic driven safety rod using FSI method

International Nuclear Information System (INIS)

Jung, Jaeho; Kim, Sanghaun; Yoo, Yeonsik; Cho, Yeonggarp; Kim, Jong In

2013-01-01

Hydraulic driven safety rod which is one of them is being developed by Division for Reactor Mechanical Engineering, KAERI. In this paper the motion of this rod is simulated by fluid structure interaction (FSI) method before manufacturing for design verification and pump sizing. A newly designed hydraulic driven safety rod which is one of reactivity control mechanism is simulated using FSI method for design verification and pump sizing. The simulation is done in CFD domain with UDF. The pressure drop is changed slightly by flow rates. It means that the pressure drop is mainly determined by weight of moving part. The simulated velocity of piston is linearly proportional to flow rates so the pump can be sized easily according to the rising and drop time requirement of the safety rod using the simulation results

Flagellation of Pseudomonas aeruginosa in newly divided cells

Science.gov (United States)

Zhao, Kun; Lee, Calvin; Anda, Jaime; Wong, Gerard

2015-03-01

For monotrichous bacteria, Pseudomonas aeruginosa, after cell division, one daughter cell inherits the old flagellum from its mother cell, and the other grows a new flagellum during or after cell division. It had been shown that the new flagellum grows at the distal pole of the dividing cell when the two daughter cells haven't completely separated. However, for those daughter cells who grow new flagella after division, it still remains unknown at which pole the new flagellum will grow. Here, by combining our newly developed bacteria family tree tracking techniques with genetic manipulation method, we showed that for the daughter cell who did not inherit the old flagellum, a new flagellum has about 90% chances to grow at the newly formed pole. We proposed a model for flagellation of P. aeruginosa.

Surface ultrastuctures of the human laryngeal mucosa - observation by an newly developed technique of SEM cinematography

International Nuclear Information System (INIS)

Ohyama, M.; Ohno, I.; Fujita, T.; Adachi, K.

1981-01-01

With the newly-developed techniques of SEM cinematography, surface ultrastructures of the human normal and pathological laryngeal mucosa were demonstrated. The high specialization of the laryngeal mucosa with its marked regional differences stresses the fact that even the squamous epithelium and nonciliated epithelium may play a role of utmost importance. All specimens were obtained after laryngectomy from 10 patients affected by laryngeal cancer which had been treated with or without preoperative irradiation of Lineac in total doses of 3,500-4,500 rad. Special attention was paid to the occurrence of microvilli and microplicae in the normal and pathological mucosa of the larynx, and their morphological and physiological significances were discussed briefly. (Auth.)

Transferability of Newly Developed Pear SSR Markers to Other Rosaceae Species.

Science.gov (United States)

Fan, L; Zhang, M-Y; Liu, Q-Z; Li, L-T; Song, Y; Wang, L-F; Zhang, S-L; Wu, J

2013-01-01

A set of 120 simple sequence repeats (SSRs) was developed from the newly assembled pear sequence and evaluated for polymorphisms in seven genotypes of pear from different genetic backgrounds. Of these, 67 (55.8 %) primer pairs produced polymorphic amplifications. Together, the 67 SSRs detected 277 alleles with an average of 4.13 per locus. Sequencing of the amplification products from randomly picked loci NAUPy31a and NAUpy53a verified the presence of the SSR loci. When the 67 primer pairs were tested on 96 individual members of eight species in the Rosaceae family, 61.2 % (41/67) of the tested SSRs successfully amplified a PCR product in at least one of the Rosaceae genera. The transferability from pear to different species varied from 58.2 % (apple) to 11.9 % (cherry). The ratio of transferability also reflected the closer relationships within Maloideae over Prunoideae. Two pear SSR markers, NAUpy43c and NAUpy55k, could distinguish the 20 different apple genotypes thoroughly, and UPGMA cluster analysis grouped them into three groups at the similarity level of 0.56. The high level of polymorphism and good transferability of pear SSRs to Rosaceae species indicate their promise for application to future molecular screening, map construction, and comparative genomic studies among pears and other Rosaceae species.

Development of micro pattern cutting simulation software

International Nuclear Information System (INIS)

Lee, Jong Min; Song, Seok Gyun; Choi, Jeong Ju; Novandy, Bondhan; Kim, Su Jin; Lee, Dong Yoon; Nam, Sung Ho; Je, Tae Jin

2008-01-01

The micro pattern machining on the surface of wide mold is not easy to be simulated by conventional software. In this paper, a software is developed for micro pattern cutting simulation. The 3d geometry of v-groove, rectangular groove, pyramid and pillar patterns are visualized by c++ and OpenGL library. The micro cutting force is also simulated for each pattern

CAPS Simulation Environment Development

Science.gov (United States)

Murphy, Douglas G.; Hoffman, James A.

2005-01-01

The final design for an effective Comet/Asteroid Protection System (CAPS) will likely come after a number of competing designs have been simulated and evaluated. Because of the large number of design parameters involved in a system capable of detecting an object, accurately determining its orbit, and diverting the impact threat, a comprehensive simulation environment will be an extremely valuable tool for the CAPS designers. A successful simulation/design tool will aid the user in identifying the critical parameters in the system and eventually allow for automatic optimization of the design once the relationships of the key parameters are understood. A CAPS configuration will consist of space-based detectors whose purpose is to scan the celestial sphere in search of objects likely to make a close approach to Earth and to determine with the greatest possible accuracy the orbits of those objects. Other components of a CAPS configuration may include systems for modifying the orbits of approaching objects, either for the purpose of preventing a collision or for positioning the object into an orbit where it can be studied or used as a mineral resource. The Synergistic Engineering Environment (SEE) is a space-systems design, evaluation, and visualization software tool being leveraged to simulate these aspects of the CAPS study. The long-term goal of the SEE is to provide capabilities to allow the user to build and compare various CAPS designs by running end-to-end simulations that encompass the scanning phase, the orbit determination phase, and the orbit modification phase of a given scenario. Herein, a brief description of the expected simulation phases is provided, the current status and available features of the SEE software system is reported, and examples are shown of how the system is used to build and evaluate a CAPS detection design. Conclusions and the roadmap for future development of the SEE are also presented.

The role of computer simulation in nuclear technologies development

International Nuclear Information System (INIS)

Tikhonchev, M.Yu.; Shimansky, G.A.; Lebedeva, E.E.; Lichadeev, V. V.; Ryazanov, D.K.; Tellin, A.I.

2001-01-01

In the report the role and purposes of computer simulation in nuclear technologies development is discussed. The authors consider such applications of computer simulation as nuclear safety researches, optimization of technical and economic parameters of acting nuclear plant, planning and support of reactor experiments, research and design new devices and technologies, design and development of 'simulators' for operating personnel training. Among marked applications the following aspects of computer simulation are discussed in the report: neutron-physical, thermal and hydrodynamics models, simulation of isotope structure change and damage dose accumulation for materials under irradiation, simulation of reactor control structures. (authors)

Virtual Collaborative Simulation Environment for Integrated Product and Process Development

Science.gov (United States)

Gulli, Michael A.

1997-01-01

Deneb Robotics is a leader in the development of commercially available, leading edge three- dimensional simulation software tools for virtual prototyping,, simulation-based design, manufacturing process simulation, and factory floor simulation and training applications. Deneb has developed and commercially released a preliminary Virtual Collaborative Engineering (VCE) capability for Integrated Product and Process Development (IPPD). This capability allows distributed, real-time visualization and evaluation of design concepts, manufacturing processes, and total factory and enterprises in one seamless simulation environment.

Cross-Linking Mast Cell Specific Gangliosides Stimulates the Release of Newly Formed Lipid Mediators and Newly Synthesized Cytokines

Directory of Open Access Journals (Sweden)

Edismauro Garcia Freitas Filho

2016-01-01

Full Text Available Mast cells are immunoregulatory cells that participate in inflammatory processes. Cross-linking mast cell specific GD1b derived gangliosides by mAbAA4 results in partial activation of mast cells without the release of preformed mediators. The present study examines the release of newly formed and newly synthesized mediators following ganglioside cross-linking. Cross-linking the gangliosides with mAbAA4 released the newly formed lipid mediators, prostaglandins D2 and E2, without release of leukotrienes B4 and C4. The effect of cross-linking these gangliosides on the activation of enzymes in the arachidonate cascade was then investigated. Ganglioside cross-linking resulted in phosphorylation of cytosolic phospholipase A2 and increased expression of cyclooxygenase-2. Translocation of 5-lipoxygenase from the cytosol to the nucleus was not induced by ganglioside cross-linking. Cross-linking of GD1b derived gangliosides also resulted in the release of the newly synthesized mediators, interleukin-4, interleukin-6, and TNF-α. The effect of cross-linking the gangliosides on the MAP kinase pathway was then investigated. Cross-linking the gangliosides induced the phosphorylation of ERK1/2, JNK1/2, and p38 as well as activating both NFκB and NFAT in a Syk-dependent manner. Therefore, cross-linking the mast cell specific GD1b derived gangliosides results in the activation of signaling pathways that culminate with the release of newly formed and newly synthesized mediators.

International and Domestic Development Trends of Electromagnetic Transient Analysis Programs for Power Systems

Science.gov (United States)

Noda, Taku

Nowadays, there is quite high demand for electromagnetic transient (EMT) analysis programs and real-time simulators for power systems. In addition to the conventional demand such as overvoltage, over-current and oscillation simulations, the new demand that includes simulations of power-electronics circuits and power quality is increasing. With this background, development groups of EMT programs and real-time simulators have made progress in terms of computational performance and user experience. In Japan, Central Research Institute of Electric Power Industry has newly developed an EMT analysis program called XTAP (eXpandable Transient Analysis Program). This article overviews these international and domestic development trends of EMT analysis programs and real-time simulators.

Development and testing of a mobile application to support diabetes self-management for people with newly diagnosed type 2 diabetes: a design thinking case study.

Science.gov (United States)

Petersen, Mira; Hempler, Nana F

2017-06-26

Numerous mobile applications have been developed to support diabetes-self-management. However, the majority of these applications lack a theoretical foundation and the involvement of people with diabetes during development. The aim of this study was to develop and test a mobile application (app) supporting diabetes self-management among people with newly diagnosed type 2 diabetes using design thinking. The app was developed and tested in 2015 using a design-based research approach involving target users (individuals newly diagnosed with type 2 diabetes), research scientists, healthcare professionals, designers, and app developers. The research approach comprised three major phases: inspiration, ideation, and implementation. The first phase included observations of diabetes education and 12 in-depth interviews with users regarding challenges and needs related to living with diabetes. The ideation phrase consisted of four interactive workshops with users focusing on app needs, in which ideas were developed and prioritized. Finally, 14 users tested the app over 4 weeks; they were interviewed about usability and perceptions about the app as a support tool. A multifunctional app was useful for people with newly diagnosed type 2 diabetes. The final app comprised five major functions: overview of diabetes activities after diagnosis, recording of health data, reflection games and goal setting, knowledge games and recording of psychological data such as sleep, fatigue, and well-being. Users found the app to be a valuable tool for support, particularly for raising their awareness about their psychological health and for informing and guiding them through the healthcare system after diagnosis. The design thinking processes used in the development and implementation of the mobile health app were crucial to creating value for users. More attention should be paid to the training of professionals who introduce health apps. Danish Data Protection Agency: 2012-58-0004. Registered 6

Newly Homeless Youth Typically Return Home

OpenAIRE

Milburn, Norweeta G.; Rosenthal, Doreen; Rotheram-Borus, Mary Jane; Mallett, Shelley; Batterham, Philip; Rice, Eric; Solorio, Rosa

2007-01-01

165 newly homeless adolescents from Melbourne, Australia and 261 from Los Angeles, United States were surveyed and followed for two years. Most newly homeless adolescents returned home (70% U.S., 47% Australia) for significant amounts of time (39% U.S., 17% Australia more than 12 months) within two years of becoming homeless.

Technetium-99m carboxymethylcellulose: A newly developed fibre marker for gastric emptying studies

International Nuclear Information System (INIS)

Schade, J.H.; Hoving, J.; Brouweres, J.R.B.J.; Riedstra-van Gent, H.G.; Zijlstra, J.; Dijkstra, J.P.H.

1991-01-01

We report a study of technetium-99m-labelled carboxymethyl-cellulose ( 99m Tc-CMC) as a newly developed non-digestible marker of the solid phase of gastric contents. The radiosynthesis is simple and shows a high labelling efficiency. In vitro and in vivo experiments demonstrated stability of the marker in the gastrointestinal tract during the process of gastric emptying. The gastric half-emptying time in ten healthy volunteers of both sexes was 105±17 min (mean±SD). This rate of gastric emptying is similar to that of non-digestible solid-phase markers such as in vivo labelled 99m Tc-chicken liver or radio-iodinated cellulose. In comparison with digestible solid-phase markers such as 99m Tc-labelled pancake or 99m Tc-cooked egg, gastric emptying of 99m Tc-CMC occurred more slowly, confirming the expected behaviour of a non-digestible solid-phase marker. We conclude that 99m Tc-CMC has the advantage of a simple and rapid labelling procedure and may be useful for clinical studies of gastric emptying. (orig.)

Developments in electron gun simulation

Science.gov (United States)

Herrmannsfeldt, W. B.

1997-01-01

This paper will discuss the developments in the electron gun simulation programs that are based on EGUN and its derivatives and supporting programs. Much of the code development has been inspired by technology changes in computer hardware; the implications on EGN2 of this evolution will be discussed. Some examples and a review of the capabilities of the EGUN family will be described.

Developments in electron gun simulation

International Nuclear Information System (INIS)

Herrmannsfeldt, W.B.

1994-05-01

This paper will discuss the developments in the electron gun simulation programs that are based on EGUN and its derivatives and supporting programs. Much of the code development has been inspired by technology changes in computer hardware; the implications on EGN2 of this evolution will be discussed. Some examples and a review of the capabilities of the EGUN family will be described

Development of a Smart Grid Simulation Environment

OpenAIRE

Delamare, J; Bitachon, B.; Peng, Z.; Wang, Y.; Haverkort, Boudewijn R.H.M.; Jongerden, M.R.

2015-01-01

With the increased integration of renewable energy sources the interaction between energy producers and consumers has become a bi-directional exchange. Therefore, the electrical grid must be adapted into a smart grid which effectively regulates this two-way interaction. With the aid of simulation, stakeholders can obtain information on how to properly develop and control the smart grid. In this paper, we present the development of an integrated smart grid simulation model, using the Anylogic ...

The role of computer simulation in nuclear technology development

International Nuclear Information System (INIS)

Tikhonchev, M.Yu.; Shimansky, G.A.; Lebedeva, E.E.; Lichadeev, VV.; Ryazanov, D.K.; Tellin, A.I.

2000-01-01

In the report, the role and purpose of computer simulation in nuclear technology development is discussed. The authors consider such applications of computer simulation as: (a) Nuclear safety research; (b) Optimization of technical and economic parameters of acting nuclear plant; (c) Planning and support of reactor experiments; (d) Research and design new devices and technologies; (f) Design and development of 'simulators' for operating personnel training. Among marked applications, the following aspects of computer simulation are discussed in the report: (g) Neutron-physical, thermal and hydrodynamics models; (h) Simulation of isotope structure change and dam- age dose accumulation for materials under irradiation; (i) Simulation of reactor control structures. (authors)

THE NEXUS BETWEEN ENERGY CONSUMPTION AND FINANCIAL DEVELOPMENT WITH ASYMMETRIC CAUSALITY TEST: NEW EVIDENCE FROM NEWLY INDUSTRIALIZED COUNTRIES

Directory of Open Access Journals (Sweden)

Feyyaz Zeren

2014-01-01

Full Text Available In this study, the relationship between energy consumption and financial development is investigated via Hatemi-J asymmetric causality test (2012 which is able to separate positive and negative shocks in analysis. In order to determine different dimensions of financial system, deposit money bank assets to GDP (dbagdp, financial system deposits to GDP (fdgdp and private credit to GDP (pcrdbgdp were used as three different indicators. As a result of this study on Newly Industrialized 7 Countries spanning the period 1971 till 2010, both positive and negative shocks existed for Malaysia and Mexico, causality from energy consumption to financial developments emerged for Philippines in only negative shocks. While two-way causality occurred for India, Turkey and Thailand, there was not for South Africa.

Design of an X-band accelerating structure using a newly developed structural optimization procedure

Energy Technology Data Exchange (ETDEWEB)

Huang, Xiaoxia [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Fang, Wencheng; Gu, Qiang [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China); Zhao, Zhentang, E-mail: zhaozhentang@sinap.ac.cn [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800 (China); University of Chinese Academy of Sciences, Beijing 100049 (China)

2017-05-11

An X-band high gradient accelerating structure is a challenging technology for implementation in advanced electron linear accelerator facilities. The present work discusses the design of an X-band accelerating structure for dedicated application to a compact hard X-ray free electron laser facility at the Shanghai Institute of Applied Physics, and numerous design optimizations are conducted with consideration for radio frequency (RF) breakdown, RF efficiency, short-range wakefields, and dipole/quadrupole field modes, to ensure good beam quality and a high accelerating gradient. The designed X-band accelerating structure is a constant gradient structure with a 4π/5 operating mode and input and output dual-feed couplers in a racetrack shape. The design process employs a newly developed effective optimization procedure for optimization of the X-band accelerating structure. In addition, the specific design of couplers providing high beam quality by eliminating dipole field components and reducing quadrupole field components is discussed in detail.

Duplex ultrasound: Indications and findings in a newly created ...

African Journals Online (AJOL)

Duplex ultrasound: Indications and findings in a newly created facility at the University of Calabar Teaching Hospital, Calabar. ... It is recommended that timely referrals be made, and mobile Doppler units be acquired to save more lives and limbs in the developing world. Keywords: Calabar, deep venous thrombosis, duplex ...

Competence of newly qualified registered nurses from a nursing college

Directory of Open Access Journals (Sweden)

BG Morolong

2005-09-01

Full Text Available The South African education and training system, through its policy of outcomesbased education and training, has made competency a national priority. In compliance to this national requirement of producing competent learners, the South African Nursing Council ( 1999 B require that the beginner professional nurse practitioners and midwives have the necessary knowledge, skills, attitudes and values which will enable them to render efficient professional service. The health care system also demands competent nurse practitioners to ensure quality in health care. In the light of competency being a national priority and a statutory demand, the research question that emerges is, how competent are the newly qualified registered nurses from a specific nursing college in clinical nursing education? A quantitative, non-experimental contextual design was used to evaluate the competence of newly qualified registered nurses from a specific nursing college. The study was conducted in two phases. The first phase dealt with the development of an instrument together with its manual through the conceptualisation process. The second phase focused on the evaluation of the competency of newly qualified nurses using the instrument based on the steps of the nursing process. A pilot study was conducted to test the feasibility of the items of the instrument. During the evaluation phase, a sample of twenty-six newly qualified nurses was selected by simple random sampling from a target population of thirty-six newly qualified registered nurses. However, six participants withdrew from the study. Data was collected in two general hospitals where the newly qualified registered nurses were working. Observation and questioning were used as data collection techniques in accordance with the developed instrument. Measures were taken to ensure internal validity and reliability of the results. To protect the rights of the participants, the researcher adhered to DENOSA’S (1998

A newly developed grab sampling system for collecting stratospheric air over Antarctica

Directory of Open Access Journals (Sweden)

Hideyuki Honda

1996-07-01

Full Text Available In order to measure the concentrations of various minor constituents and their isotopic ratios in the stratosphere over Antarctica, a simple grab sampling system was newly developed. The sampling system was designed to be launched by a small number of personnel using a rubber balloon under severe experimental conditions. Special attention was paid to minimize the contamination of sample air, as well as to allow easy handling of the system. The sampler consisted mainly of a 15l sample container with electromagnetic and manual valves, control electronics for executing the air sampling procedures and sending the position and status information of the sampler to the ground station, batteries and a transmitter. All these parts were assembled in an aluminum frame gondola with a shock absorbing system for landing. The sampler was equipped with a turn-over mechanism of the gondola to minimize contamination from the gondola, as well as with a GPS receiver and a rawinsonde for its tracking. Total weight of the sampler was about 11kg. To receive, display and store the position and status data of the sampling system at the ground station, a simple data acquisition system with a portable receiver and a microcomputer was also developed. A new gas handling system was prepared to simplify the injection of He gas into the balloon. For air sampling experiments, three sampling systems were launched at Syowa Station (69°00′S, 39°35′E, Antarctica and then recovered on sea ice near the station on January 22 and 25,1996.

Evaluation of newly developed veterinary portable blood glucose meter with hematocrit correction in dogs and cats.

Science.gov (United States)

Mori, Akihiro; Oda, Hitomi; Onozawa, Eri; Shono, Saori; Sako, Toshinori

2017-10-07

This study evaluated the accuracy of a newly developed veterinary portable blood glucose meter (PBGM) with hematocrit correction in dogs and cats. Sixty-one dogs and 31 cats were used for the current study. Blood samples were obtained from each dog and cat one to six times. Acceptable results were obtained in error grid analysis between PBGM and reference method values (glucose oxidation methods) in both dogs and cats. Bland-Altman plot analysis revealed a mean difference between the PBGM value and reference method value of -1.975 mg/dl (bias) in dogs and 1.339 mg/dl (bias) in cats. Hematocrit values did not affect the results of the veterinary PBGM. Therefore, this veterinary PBGM is clinically useful in dogs and cats.

Newly-graduated midwives transcending barriers: a grounded theory study.

Science.gov (United States)

Barry, Michele J; Hauck, Yvonne L; O'Donoghue, Thomas; Clarke, Simon

2013-12-01

Midwifery has developed its own philosophy to formalise its unique identity as a profession. Newly-graduated midwives are taught, and ideally embrace, this philosophy during their education. However, embarking in their career within a predominantly institutionalised and the medically focused health-care model may challenge this application. The research question guiding this study was as follows: 'How do newly graduated midwives deal with applying the philosophy of midwifery in their first six months of practice?' The aim was to generate a grounded theory around this social process. This Western Australian grounded theory study is conceptualised within the social theory of symbolic interactionism. Data were collected by means of in-depth, semi-structured interviews with 11 recent midwifery graduates. Participant and interviewer's journals provided supplementary data. The 'constant comparison' approach was used for data analysis. The substantive theory of transcending barriers was generated. Three stages in transcending barriers were identified: Addressing personal attributes, Understanding the 'bigger picture', and finally, 'Evaluating, planning and acting' to provide woman-centred care. An overview of these three stages provides the focus of this article. The theory of transcending barriers provides a new perspective on how newly-graduated midwives deal with applying the philosophy of midwifery in their first six months of practice. A number of implications for pre and post registration midwifery education and policy development are suggested, as well as recommendations for future research. Copyright © 2013 Elsevier Ltd. All rights reserved.

A newly developed lubricant, chitosan laurate, in the manufacture of acetaminophen tablets.

Science.gov (United States)

Bani-Jaber, Ahmad; Kobayashi, Asuka; Yamada, Kyohei; Haj-Ali, Dana; Uchimoto, Takeaki; Iwao, Yasunori; Noguchi, Shuji; Itai, Shigeru

2015-04-10

To study the usefulness of chitosan laurate (CS-LA), a newly developed chitosan salt, as a lubricant, lubrication properties such as the pressure transmission ratio and ejection force were determined at different concentrations of CS-LA in tableting. In addition, tablet properties such as the tensile strength, disintegration time, and dissolution behavior, were also determined. When CS-LA was mixed at concentrations of 0.1%-3.0%, the pressure transmission ratio was increased in a concentration-dependent manner, and the value at a CS-LA concentration of 3% was equal to that of magnesium stearate (Mg-St), a widely used lubricant. Additionally, a reduction in the ejection force was observed at a concentration from 1%, proving that CS-LA has good lubrication performance. A prolonged disintegration time and decreased tensile strength, which are known disadvantages of Mg-St, were not observed with CS-LA. Furthermore, with CS-LA, retardation of dissolution of the drug from the tablets was not observed. Conjugation of CS with LA was found to be quite important for both lubricant and tablet properties. In conclusion, CS-LA should be useful as an alternative lubricant to Mg-St. Copyright © 2015 Elsevier B.V. All rights reserved.

Development of Nuclear ship Engineering Simulation SYstem (NESSY)

International Nuclear Information System (INIS)

Kusunoki, Tsuyoshi; Kyouya, Masahiko; Takahashi, Teruo; Kobayashi, Hideo; Ochiai, Masa-aki; Hashidate, Kouji.

1993-11-01

NESSY has been developed for design studies of advanced marine reactors as a part of nuclear ship research and development since 1987. Engineering simulation model of the Mutsu, which is the first nuclear ship in Japan, was completed in March of 1993. In this report we concentration on detail description of softwares for Mutsu modeling. The aims of development of NESSY are as follows; (1) Assessment and confirmation on plant performance of an advanced marine reactor in each step of nuclear ship design (2) Development of abnormality diagnosis system and operator support system as a part of enhanced automization study, and study of human interface with hardware The characteristics of NESSY are the followings. (1) Total engineering simulation system simulate simultaneously ship motions, propulsion system behavior, and nuclear plant behavior under given weather and sea conditions. (2) Models based on physical theory as far as possible. (3) The simulator has high extensibility and flexibility. It is able to apply to other reactors, as the simulation model consists of the part of basic model and the part of plant data which are easy to change. After completion of Mutsu modeling, we are planning to utilize this system as one of design tools for an advanced marine reactor. (author)

Practical considerations in developing numerical simulators for thermal recovery

Energy Technology Data Exchange (ETDEWEB)

Abou-Kassem, J.H. [Chemical and Petroleum Engineering Department, UAE University, Al-Ain (United Arab Emirates)

1996-08-15

Numerical simulation of steam injection and in-situ combustion-based oil recovery processes is of great importance in project design. Development of such numerical simulators is an on-going process, with improvements made as the process description becomes more complete, and also as better methods are devised to resolve certain numerical difficulties. This paper addresses some of the latter, and based on the author`s experience gives useful guidelines for developing more efficient numerical simulators of steam injection and in-situ combustion. The paper takes up a series of questions related to simulating thermal processes. Included are: the elimination of constraint equations at the matrix level, phase change, steam injection rate, alternative treatments of heat loss, relative permeabilities and importance of hysteresis effects, improved solutions to the grid orientation problem and other simulation problems such as potential inversion, grid block size, time-step size control and induced fractures. The points discussed in the paper should be of use to both simulator developers and users alike, and will lead to a better understanding of simulation results

Transferring Nuclear Knowledge by NPP Simulators Developers

International Nuclear Information System (INIS)

Levchenko, A.; Duginov, O.; Levchenko, V.

2016-01-01

Full text: In relation to nuclear power, safety is closely linked with the human factor. Knowledge and skills of staff should more closely match the needs of the industry and employers. This can be achieved through more efficient training using simulators. Such simulators must be available at all stages of study and cover the needs of trainees with different levels of knowledge. Simulator developers can solve this problem by implement knowledge management in the using of simulators for practical training. Due to the nature of their activities, they have everything needed for this. This paper describes the solutions of Simulation Systems Ltd Company for nuclear power plants, universities and other parties. (author

Computational simulations of direct contact condensation as the driving force for water hammer

International Nuclear Information System (INIS)

Ceuca, Sabin-Cristian

2015-01-01

An analysis, based on Computer Simulations of the Direct Contact Condensation as the Driving Force for the Condensation Induced Water Hammer phenomenon is performed within this thesis. The goal of the work is to develop a mechanistic HTC model, with predictive capabilities for the simulation of horizontal or nearly horizontal two-phase ows with complex patterns including the e ect of interfacial heat and mass transfer. The newly developed HTC model was implemented into the system code ATHLET and into the CFD tools ANSYS CFX and OpenFOAM. Validation calculations have been performed for horizontal or nearly horizontal ows, where simulation results have been compared against the local measurement data such as void and temperature or area averaged data delivered by a wire mesh sensor.

Computational simulations of direct contact condensation as the driving force for water hammer

Energy Technology Data Exchange (ETDEWEB)

Ceuca, Sabin-Cristian

2015-04-27

An analysis, based on Computer Simulations of the Direct Contact Condensation as the Driving Force for the Condensation Induced Water Hammer phenomenon is performed within this thesis. The goal of the work is to develop a mechanistic HTC model, with predictive capabilities for the simulation of horizontal or nearly horizontal two-phase ows with complex patterns including the e ect of interfacial heat and mass transfer. The newly developed HTC model was implemented into the system code ATHLET and into the CFD tools ANSYS CFX and OpenFOAM. Validation calculations have been performed for horizontal or nearly horizontal ows, where simulation results have been compared against the local measurement data such as void and temperature or area averaged data delivered by a wire mesh sensor.

Development of a training simulator for offshore crane operators

Energy Technology Data Exchange (ETDEWEB)

Cooper, S.J.

2003-01-01

The crane simulator, trade name KraneSIM-6000, underpins an integrated training package developed to provide crane operator exposure to simulated normal and dangerous conditions in a safe training environment. The prototype simulator is significantly more sophisticated than the system initially envisaged: a number of conceptual changes incorporated during its development ensured that the very latest in simulation computer technology was incorporate unique in that it offers the opportunity to practice the lifting and laying down of loads between a moving (floating) rig and moving supply vessels, together with the possibility of benchmarking crane operator competency. Concludes that there is great scope for expansion of the simulator facilities so far developed. In particular, it is recognised that training and competency testing of teams of personnel such as banksman and supply ship's master could be integrated into crane simulator training scenarios, and that this approach offers great potential for reducing the number of crane related accidents. (Author)

Immunoparesis in newly diagnosed Multiple Myeloma patients

DEFF Research Database (Denmark)

Sorrig, Rasmus; Klausen, Tobias W.; Salomo, Morten

2017-01-01

Immunoparesis (hypogammaglobulinemia) is associated to an unfavorable prognosis in newly diagnosed Multiple myeloma (MM) patients. However, this finding has not been validated in an unselected population-based cohort. We analyzed 2558 newly diagnosed MM patients in the Danish Multiple Myeloma...

Building of Nuclear Ship Engineering Simulation System development of the simulator for the integral type reactor

Energy Technology Data Exchange (ETDEWEB)

Takahashi, Teruo; Shimazaki, Junya; Yabuuchi, Noriaki; Fukuhara, Yosifumi; Kusunoki, Takeshi; Ochiai, Masaaki [Department of Nuclear Energy Systems, Tokai Research Establishment, Japan Atomic Energy Research Institute, Tokai, Ibaraki (Japan); Nakazawa, Toshio [Department of HTTR Project, Oarai Research Establishment, Japan Atomic Energy Research Institute, Oarai, Ibaraki (Japan)

2000-03-01

JAERI had carried out the design study of a light-weight and compact integral type reactor of power 100 MW{sub th} with passive safety as a power source for the future nuclear ships, and completed an engineering design. To confirm the design and operation performance and to utilize the study of automation of the operations of reactor, we developed a real-time simulator for the integral type reactor. This simulator is a part of Nuclear Ship Engineering Simulation System (NESSY) and on the same hardware as 'Mutsu' simulator which was developed to simulate the first Japanese nuclear ship Mutsu'. Simulation accuracy of 'Mutsu' simulator was verified by comparing the simulation results With data got in the experimental voyage of 'Mutsu'. The simulator for the integral type reactor uses the same programs which were used in 'Mutsu' simulator for the separate type PWR, and the simulated results are approximately consistent with the calculated values using RELAP5/MOD2 (The later points are reported separately). Therefore simulation accuracy of the simulator for the integral type reactor is also expected to be reasonable, though it is necessary to verify by comparing with the real plant data or experimental data in future. We can get the perspectives to use as a real-time engineering simulator and to achieve the above-mentioned aims. This is a report on development of the simulator for the integral type reactor mainly focused on the contents of the analytical programs expressed the structural features of reactor. (author)

Construction and simulation of a novel continuous traffic flow model

International Nuclear Information System (INIS)

Hwang, Yao-Hsin; Yu, Jui-Ling

2017-01-01

In this paper, we aim to propose a novel mathematical model for traffic flow and apply a newly developed characteristic particle method to solve the associate governing equations. As compared with the existing non-equilibrium higher-order traffic flow models, the present one is put forward to satisfy the following three conditions: 1.Preserve the equilibrium state in the smooth region. 2.Yield an anisotropic propagation of traffic flow information. 3.Expressed with a conservation law form for traffic momentum. These conditions will ensure a more practical simulation in traffic flow physics: The current traffic will not be influenced by the condition in the behind and result in unambiguous condition across a traffic shock. Through analyses of characteristics, stability condition and steady-state solution adherent to the equation system, it is shown that the proposed model actually conform to these conditions. Furthermore, this model can be cast into its characteristic form which, incorporated with the Rankine-Hugoniot relation, is appropriate to be simulated by the characteristic particle method to obtain accurate computational results. - Highlights: • The traffic model expressed with the momentum conservation law. • Traffic flow information propagate anisotropically and preserve the equilibrium state in the smooth region. • Computational particles of two families are invented to mimic forward-running and backward-running characteristics. • Formation of shocks will be naturally detected by the intersection of computational particles of same family. • A newly developed characteristic particle method is used to simulate traffic flow model equations.

An Efficient and Robust Method for Lagrangian Magnetic Particle Tracking in Fluid Flow Simulations on Unstructured Grids

NARCIS (Netherlands)

Cohen Stuart, D.C.; Kleijn, C.R.; Kenjeres, S.

2010-01-01

In this paper we report on a newly developed particle tracking scheme for fluid flow simulations on 3D unstructured grids, aiming to provide detailed insights in the particle behaviour in complex geometries. A possible field of applications is the Magnetic Drug Targeting (MDT) technique, on which

Development of Spaceborne Radar Simulator by NICT and JAXA using JMA Cloud-resolving Model

Science.gov (United States)

Kubota, T.; Eito, H.; Aonashi, K.; Hashimoto, A.; Iguchi, T.; Hanado, H.; Shimizu, S.; Yoshida, N.; Oki, R.

2009-12-01

We are developing synthetic spaceborne radar data toward a simulation of the Dual-frequency Precipitation Radar (DPR) aboard the Global Precipitation Measurement (GPM) core-satellite. Our purposes are a production of test-bed data for higher level DPR algorithm developers, in addition to a diagnosis of a cloud resolving model (CRM). To make the synthetic data, we utilize the CRM by the Japan Meteorological Agency (JMA-NHM) (Ikawa and Saito 1991, Saito et al. 2006, 2007), and the spaceborne radar simulation algorithm by the National Institute of Information and Communications Technology (NICT) and the Japan Aerospace Exploration Agency (JAXA) named as the Integrated Satellite Observation Simulator for Radar (ISOSIM-Radar). The ISOSIM-Radar simulates received power data in a field of view of the spaceborne radar with consideration to a scan angle of the radar (Oouchi et al. 2002, Kubota et al. 2009). The received power data are computed with gaseous and hydrometeor attenuations taken into account. The backscattering and extinction coefficients are calculated assuming the Mie approximation for all species. The dielectric constants for solid particles are computed by the Maxwell-Garnett model (Bohren and Battan 1982). Drop size distributions are treated in accordance with those of the JMA-NHM. We assume a spherical sea surface, a Gaussian antenna pattern, and 49 antenna beam directions for scan angles from -17 to 17 deg. in the PR. In this study, we report the diagnosis of the JMA-NHM with reference to the TRMM Precipitation Radar (PR) and CloudSat Cloud Profiling Radar (CPR) using the ISOSIM-Radar from the view of comparisons in cloud microphysics schemes of the JMA-NHM. We tested three kinds of explicit bulk microphysics schemes based on Lin et al. (1983), that is, three-ice 1-moment scheme, three-ice 2-moment scheme (Eito and Aonashi 2009), and newly developed four-ice full 2-moment scheme (Hashimoto 2008). The hydrometeor species considered here are rain, graupel

A powerful tool for plant specific simulations

International Nuclear Information System (INIS)

Boucau, J.; Ofstun, R.

1988-01-01

Following the Three Mile Island (TMI) accident, special emphasis has been placed by the Utilities and Safety Authorities on the training of plant operators and engineers to make them more familiar with the dynamic behavior of the plant in post-accident conditions. With a view to providing transient response under realistic operating conditions, concerns were raised over: the use of conservative safety analysis models for analyzing operational and accident transients; the ability to dynamically simulate the expected operator actions, and the need to simulate the plant during long term cooling recovery. To meet these requirements, an interactive, user friendly, cost efficient dynamic model capable of simulating two-phase conditions is needed. In response to these post-TMI concerns, Westinghouse has developed, the Transient Real-Time Engineering Analysis Tool (TREAT) which is a general purpose interactive thermal-hydraulic network code for thermal-hydraulic transient analysis. The applications of TREAT are numerous and range from engineering studies to plant operator training using the newly developed TREAT SIMULATOR. The purpose of this paper is to describe the TREAT program and potential applications. Special emphasis will be drawn at a plant specific training application performed for a French 4-loop plant

High-speed BWR power plant simulations on the special-purpose peripheral processor AD10

International Nuclear Information System (INIS)

Wulff, W.; Cheng, H.S.; Lekach, S.V.; Mallen, A.N.

1985-01-01

A newly developed technique is described for fast, on-line simulations of normal and accidental transients in nuclear power plants. The technique is based on the utilization of the special-purpose peripheral processor AD10, which is specifically designed for high-speed systems simulations through integration of large systems of nonlinear ordinary differential equations. The Peach Bottom-II Boiling Water Reactor power plant has been simulated and results are presented. It is shown that the new technique not only advances safety analyses but also supports plant monitoring, failure diagnosis and accident mitigation, as well as the training of nuclear power plant operators. (author)

Role of ion simulation in CTR materials development

International Nuclear Information System (INIS)

Nolfi, F.V. Jr.

1976-01-01

This paper discusses the role of ion simulation in the U.S. fusion power development program, evaluates various ion and neutron simulation techniques, emphasizes the need for quantitative correlation between ion and high-energy neutron radiation damage, and outlines the essential features of ion/neutron simulation experiments on candidate first-wall materials

Retrieval process development and enhancements waste simulant compositions and defensibility

International Nuclear Information System (INIS)

Powell, M.R.; Golcar, G.R.; Geeting, J.G.H.

1997-09-01

The purpose of this report is to document the physical waste simulant development efforts of the EM-50 Tanks Focus Area at the Hanford Site. Waste simulants are used in the testing and development of waste treatment and handling processes because performing such tests using actual tank waste is hazardous and prohibitively expensive. This document addresses the simulant development work that supports the testing of waste retrieval processes using simulants that mimic certain key physical properties of the tank waste. Development and testing of chemical simulants are described elsewhere. This work was funded through the EM-50 Tanks Focus Area as part of the Retrieval Process Development and Enhancements (RPD ampersand E) Project at the Pacific Northwest National Laboratory (PNNL). The mission of RPD ampersand E is to understand retrieval processes, including emerging and existing processes, gather performance data on those processes, and relate the data to specific tank problems to provide end users with the requisite technical bases to make retrieval and closure decisions. Physical simulants are prepared using relatively nonhazardous and inexpensive materials rather than the chemicals known to be in tank waste. Consequently, only some of the waste properties are matched by the simulant. Deciding which properties need to be matched and which do not requires a detailed knowledge of the physics of the process to be tested using the simulant. Developing this knowledge requires reviews of available literature, consultation with experts, and parametric tests. Once the relevant properties are identified, waste characterization data are reviewed to establish the target ranges for each property. Simulants are then developed that possess the desired ranges of properties

Simulation of oat development cycle by photoperiod and temperature

Directory of Open Access Journals (Sweden)

Rubia D. Mantai

Full Text Available ABSTRACT The simulation of oat development cycle can be used in the planning of agricultural practices. The aim of the study was to simulate and validate the duration of oat development cycle by photoperiod, temperature and coefficients of development of wheat for use in the WE-Streck model, considering different doses of N-fertilizer and systems of succession of high and low C/N ratio. The study was conducted in 2015 in a randomized block design with four replicates in a 4 x 2 factorial scheme, corresponding to N rates (0, 30, 60 and 120 kg ha-1 and oat cultivars (Barbarasul and Brisasul, respectively, in the soybean/oat and maize/oat systems. The duration of the stages from emergence to anthesis and from anthesis to maturation of oats was simulated in the WE-Streck model. The minimum, optimum and maximum temperatures that effectively simulate the oat development cycle were 4, 22 and 30 °C from emergence to anthesis and 15, 25 and 35 °C from anthesis to maturation, respectively. The intermediate-cycle oat development was efficiently simulated by the WE-Streck model using coefficients developed for wheat, with vegetative and reproductive cycles estimated at 89 and 43 days, respectively.

Leadership Development Through Peer-Facilitated Simulation in Nursing Education.

Science.gov (United States)

Brown, Karen M; Rode, Jennifer L

2018-01-01

Baccalaureate nursing graduates must possess leadership skills, yet few opportunities exist to cultivate leadership abilities in a clinical environment. Peer-facilitated learning may increase the leadership skills of competence, self-confidence, self-reflection, and role modeling. Facilitating human patient simulation provides opportunities to develop leadership skills. With faculty supervision, senior baccalaureate students led small-group simulation experiences with sophomore and junior peers and then conducted subsequent debriefings. Quantitative and qualitative descriptive data allowed evaluation of students' satisfaction with this teaching innovation and whether the experience affected students' desire to take on leadership roles. Students expressed satisfaction with the peer-facilitated simulation experience and confidence in mastering the content while developing necessary skills for practice. Peer-facilitated simulation provides an opportunity for leadership development and learning. Study results can inform the development of nursing curricula to best develop the leadership skills of nursing students. [J Nurs Educ. 2018;57(1):53-57.]. Copyright 2018, SLACK Incorporated.

SimulaQron - A simulator for developing quantum internet software

OpenAIRE

Dahlberg, Axel; Wehner, Stephanie

2017-01-01

We introduce a simulator for a quantum internet with the specific goal to support software development. A quantum internet consists of local quantum processors, which are interconnected by quantum communication channels that enable the transmission of qubits between the different processors. While many simulators exist for local quantum processors, there is presently no simulator for a quantum internet tailored towards software development. Quantum internet protocols require both classical as...

A Newly Developed Method for Computing Reliability Measures in a Water Supply Network

Directory of Open Access Journals (Sweden)

Jacek Malinowski

2016-01-01

Full Text Available A reliability model of a water supply network has beens examined. Its main features are: a topology that can be decomposed by the so-called state factorization into a (relativelysmall number of derivative networks, each having a series-parallel structure (1, binary-state components (either operative or failed with given flow capacities (2, a multi-state character of the whole network and its sub-networks - a network state is defined as the maximal flow between a source (sources and a sink (sinks (3, all capacities (component, network, and sub-network have integer values (4. As the network operates, its state changes due to component failures, repairs, and replacements. A newly developed method of computing the inter-state transition intensities has been presented. It is based on the so-called state factorization and series-parallel aggregation. The analysis of these intensities shows that the failure-repair process of the considered system is an asymptotically homogenous Markov process. It is also demonstrated how certain reliability parameters useful for the network maintenance planning can be determined on the basis of the asymptotic intensities. For better understanding of the presented method, an illustrative example is given. (original abstract

Nonlinear friction model for servo press simulation

Science.gov (United States)

Ma, Ninshu; Sugitomo, Nobuhiko; Kyuno, Takunori; Tamura, Shintaro; Naka, Tetsuo

2013-12-01

The friction coefficient was measured under an idealized condition for a pulse servo motion. The measured friction coefficient and its changing with both sliding distance and a pulse motion showed that the friction resistance can be reduced due to the re-lubrication during unloading process of the pulse servo motion. Based on the measured friction coefficient and its changes with sliding distance and re-lubrication of oil, a nonlinear friction model was developed. Using the newly developed the nonlinear friction model, a deep draw simulation was performed and the formability was evaluated. The results were compared with experimental ones and the effectiveness was verified.

Developing team cognition: A role for simulation

Science.gov (United States)

Fernandez, Rosemarie; Shah, Sachita; Rosenman, Elizabeth D.; Kozlowski, Steve W. J.; Parker, Sarah Henrickson; Grand, James A.

2016-01-01

SUMMARY STATEMENT Simulation has had a major impact in the advancement of healthcare team training and assessment. To date, the majority of simulation-based training and assessment focuses on the teamwork behaviors that impact team performance, often ignoring critical cognitive, motivational, and affective team processes. Evidence from team science research demonstrates a strong relationship between team cognition and team performance and suggests a role for simulation in the development of this team-level construct. In this article we synthesize research from the broader team science literature to provide foundational knowledge regarding team cognition and highlight best practices for using simulation to target team cognition. PMID:28704287

Generational differences among newly licensed registered nurses.

Science.gov (United States)

Keepnews, David M; Brewer, Carol S; Kovner, Christine T; Shin, Juh Hyun

2010-01-01

Responses of 2369 newly licensed registered nurses from 3 generational cohorts-Baby Boomers, Generation X, and Generation Y-were studied to identify differences in their characteristics, work-related experiences, and attitudes. These responses revealed significant differences among generations in: job satisfaction, organizational commitment, work motivation, work-to-family conflict, family-to-work conflict, distributive justice, promotional opportunities, supervisory support, mentor support, procedural justice, and perceptions of local job opportunities. Health organizations and their leaders need to anticipate intergenerational differences among newly licensed nurses and should provide for supportive working environments that recognize those differences. Orientation and residency programs for newly licensed nurses should be tailored to the varying needs of different generations. Future research should focus on evaluating the effectiveness of orientation and residency programs with regard to different generations so that these programs can be tailored to meet the varying needs of newly licensed nurses at the start of their careers. Copyright 2010 Mosby, Inc. All rights reserved.

Development of a full scope reactor engineering simulator

International Nuclear Information System (INIS)

Venhuizen, J.R.; Laats, E.T.

1988-01-01

An engineering laboratory is pursuing the development of an engineering simulator for use by several agencies of the U.S. Government. According to the authors, this simulator will provide the highest fidelity simulation with initial objectives for studying augmented nuclear reactor operator training, and later for advanced concepts testing as applicable to control room accident diagnosis and management

Development of our laser fusion integration simulation

International Nuclear Information System (INIS)

Li, J.; Zhai, C.; Li, S.; Li, X.; Zheng, W.; Yong, H.; Zeng, Q.; Hang, X.; Qi, J.; Yang, R.; Cheng, J.; Song, P.; Gu, P.; Zhang, A.; An, H.; Xu, X.; Guo, H.; Cao, X.; Mo, Z.; Pei, W.; Jiang, S.; Zhu, S. P.

2013-01-01

In the target design of the Inertial Confinement Fusion (ICF) program, it is common practice to apply radiation hydrodynamics code to study the key physical processes happening in ICF process, such as hohlraum physics, radiation drive symmetry, capsule implosion physics in the radiation-drive approach of ICF. Recently, many efforts have been done to develop our 2D integrated simulation capability of laser fusion with a variety of optional physical models and numerical methods. In order to effectively integrate the existing codes and to facilitate the development of new codes, we are developing an object-oriented structured-mesh parallel code-supporting infrastructure, called JASMIN. Based on two-dimensional three-temperature hohlraum physics code LARED-H and two-dimensional multi-group radiative transfer code LARED-R, we develop a new generation two-dimensional laser fusion code under the JASMIN infrastructure, which enable us to simulate the whole process of laser fusion from the laser beams' entrance into the hohlraum to the end of implosion. In this paper, we will give a brief description of our new-generation two-dimensional laser fusion code, named LARED-Integration, especially in its physical models, and present some simulation results of holhraum. (authors)

A simulation methodology of spacer grid residual spring deflection for predictive and interpretative purposes

International Nuclear Information System (INIS)

Kim, K. T.; Kim, H. K.; Yoon, K. H.

1994-01-01

The in-reactor fuel rod support conditions against the fretting wear-induced damage can be evaluated by spacer grid residual spring deflection. In order to predict the spacer grid residual spring deflection as a function of burnup for various spring designs, a simulation methodology of spacer grid residual spring deflection has been developed and implemented in the GRIDFORCE program. The simulation methodology takes into account cladding creep rate, initial spring deflection, initial spring force, and spring force relaxation rate as the key parameters affecting the residual spring deflection. The simulation methodology developed in this study can be utilized as an effective tool in evaluating the capability of a newly designed spacer grid spring to prevent the fretting wear-induced damage

Mentorship for newly appointed physicians: a strategy for enhancing patient safety?

Science.gov (United States)

Harrison, Reema; McClean, Serwaa; Lawton, Rebecca; Wright, John; Kay, Clive

2014-09-01

Mentorship is an increasingly popular innovation from business and industry that is being applied in health-care contexts. This paper explores the concept of mentorship for newly appointed physicians in their first substantive senior post, and specifically its utilization to enhance patient safety. Semi-structured face to face and telephone interviews with Medical Directors (n = 5), Deputy Medical Directors (n = 4), and Clinical Directors (n = 6) from 9 acute NHS Trusts in the Yorkshire and Humber region in the north of England. A focused thematic analysis was used. A number of beneficial outcomes were associated with mentorship for newly appointed physicians including greater personal and professional support, organizational commitment, and general well-being. Providing newly appointed senior physicians with support through mentorship was considered to enhance the safety of patient care. Mentorship may prevent or reduce active failures, be used to identify threats in the local working environment, and in the longer term, address latent threats to safety within the organization by encouraging a healthier safety culture. Offering mentorship to all newly appointed physicians in their first substantive post in health care may be a useful strategy to support the development of their clinical, professional, and personal skills in this transitional period that may also enhance the safety of patient care.

Developing Cognitive Models for Social Simulation from Survey Data

Science.gov (United States)

Alt, Jonathan K.; Lieberman, Stephen

The representation of human behavior and cognition continues to challenge the modeling and simulation community. The use of survey and polling instruments to inform belief states, issue stances and action choice models provides a compelling means of developing models and simulations with empirical data. Using these types of data to population social simulations can greatly enhance the feasibility of validation efforts, the reusability of social and behavioral modeling frameworks, and the testable reliability of simulations. We provide a case study demonstrating these effects, document the use of survey data to develop cognitive models, and suggest future paths forward for social and behavioral modeling.

Large-scale numerical simulations on two-phase flow behavior in a fuel bundle of RMWR with the earth simulator

International Nuclear Information System (INIS)

Kazuyuki, Takase; Hiroyuki, Yoshida; Hidesada, Tamai; Hajime, Akimoto; Yasuo, Ose

2003-01-01

Fluid flow characteristics in a fuel bundle of a reduced-moderation light water reactor (RMWR) with a tight-lattice core were analyzed numerically using a newly developed two-phase flow analysis code under the full bundle size condition. Conventional analysis methods such as sub-channel codes need composition equations based on the experimental data. In case that there are no experimental data regarding to the thermal-hydraulics in the tight-lattice core, therefore, it is difficult to obtain high prediction accuracy on the thermal design of the RMWR. Then the direct numerical simulations with the earth simulator were chosen. The axial velocity distribution in a fuel bundle changed sharply around a grid spacer and its quantitative evaluation was obtained from the present preliminary numerical study. The high prospect was acquired on the possibility of establishment of the thermal design procedure of the RMWR by large-scale direct simulations. (authors)

[An Introduction to A Newly-developed "Acupuncture Needle Manipulation Training-evaluation System" Based on Optical Motion Capture Technique].

Science.gov (United States)

Zhang, Ao; Yan, Xing-Ke; Liu, An-Guo

2016-12-25

In the present paper, the authors introduce a newly-developed "Acupuncture Needle Manipulation Training-evaluation System" based on optical motion capture technique. It is composed of two parts, sensor and software, and overcomes some shortages of mechanical motion capture technique. This device is able to analyze the data of operations of the pressing-hand and needle-insertion hand during acupuncture performance and its software contains personal computer (PC) version, Android version, and Internetwork Operating System (IOS) Apple version. It is competent in recording and analyzing information of any ope-rator's needling manipulations, and is quite helpful for teachers in teaching, training and examining students in clinical practice.

Conceptual Design of Simulation Models in an Early Development Phase of Lunar Spacecraft Simulator Using SMP2 Standard

Science.gov (United States)

Lee, Hoon Hee; Koo, Cheol Hea; Moon, Sung Tae; Han, Sang Hyuck; Ju, Gwang Hyeok

2013-08-01

The conceptual study for Korean lunar orbiter/lander prototype has been performed in Korea Aerospace Research Institute (KARI). Across diverse space programs around European countries, a variety of simulation application has been developed using SMP2 (Simulation Modelling Platform) standard related to portability and reuse of simulation models by various model users. KARI has not only first-hand experience of a development of SMP compatible simulation environment but also an ongoing study to apply the SMP2 development process of simulation model to a simulator development project for lunar missions. KARI has tried to extend the coverage of the development domain based on SMP2 standard across the whole simulation model life-cycle from software design to its validation through a lunar exploration project. Figure. 1 shows a snapshot from a visualization tool for the simulation of lunar lander motion. In reality, a demonstrator prototype on the right-hand side of image was made and tested in 2012. In an early phase of simulator development prior to a kick-off start in the near future, targeted hardware to be modelled has been investigated and indentified at the end of 2012. The architectural breakdown of the lunar simulator at system level was performed and the architecture with a hierarchical tree of models from the system to parts at lower level has been established. Finally, SMP Documents such as Catalogue, Assembly, Schedule and so on were converted using a XML(eXtensible Mark-up Language) converter. To obtain benefits of the suggested approaches and design mechanisms in SMP2 standard as far as possible, the object-oriented and component-based design concepts were strictly chosen throughout a whole model development process.

Accident simulator development for probabilistic safety analysis

International Nuclear Information System (INIS)

Cacciabue, P.C.; Amendola, A.; Mancini, G.

1985-01-01

This paper describes the basic features of a new concept of incident simulator, Response System Analyzed (RSA) which is being developed within the CEC JRC Research Program on Reactor Safety. Focusing on somewhat different aims than actual simulators, RSA development extends the field of application of simulators to the area of risk and reliability analysis and in particular to the identification of relevant sequences, to the modeling of human behavior and to the validation of operating procedures. The fundamental components of the project, i.e. the deterministic transient model of the plant, the automatic probabilistic driver and the human possible intervention modeling, are discussed in connection with the problem of their dynamic interaction. The analyses so far performed by separately testing RSA on significant study cases have shown encouraging results and have proven the feasibility of the overall program

The effect of strain distribution on microstructural developments during forging in a newly developed nickel base superalloy

Energy Technology Data Exchange (ETDEWEB)

Buckingham, R.C. [Institute of Structural Materials, Swansea University, Bay Campus, Fabian Way, Swansea SA1 8EN (United Kingdom); Argyrakis, C.; Hardy, M.C. [Rolls-Royce plc, PO Box 31, Derby DE24 8BJ (United Kingdom); Birosca, S., E-mail: 522042@swansea.ac.uk [Institute of Structural Materials, Swansea University, Bay Campus, Fabian Way, Swansea SA1 8EN (United Kingdom)

2016-01-27

In the current study, the effect of strain distribution in a simple forging geometry on the propensity for recrystallization, and its impact on mechanical properties has been investigated in a newly developed experimental nickel-based superalloy. The new alloy was produced via a Powder Metallurgy (PM) route and was subsequently Hot Isostatic Processed (HIP), isothermally forged, and heat treated to produce a coarse grain microstructure with average grain size of 23–32 μm. The alloy was examined by means of Electron Back-Scatter Diffraction (EBSD) to characterise the microstructural features such as grain orientation and morphology, grain boundary characteristics and the identification of potential Prior Particle Boundaries (PPBs) throughout each stage of the processing route. Results at the central region of the cross-section plane parallel to the loading direction showed significant microstructural differences across the forging depth. This microstructural variation was found to be highly dependent on the value of local strain imparted during forging such that areas of low effective strain showed partial recrystallisation and a necklace grain structure was observed following heat treatment. Meanwhile, a fully recrystallised microstructure with no PPBs was observed in the areas of high strain values, in the central region of the forging.

Development of Integrated Simulation System for Helical Plasmas

Energy Technology Data Exchange (ETDEWEB)

Nakamura, Y.; Yokoyama, M.; Nakajima, N.; Fukuyama, A.; Watanabe, K. Y.; Funaba, H.; Suzuki, Y.; Murakami, S.; Ida, K.; Sakakibara, S.; Yamada, H.

2005-07-01

Recent progress of computers (parallel/vector-parallel computers, PC clusters, for example) and numerical codes for helical plasmas like three-dimensional MHD equilibrium codes, combined with the development of the plasma diagnostics technique, enable us to do the detailed theoretical analyses of the individual experimental observations. Now, it is pointed out that the experimental data analysis from the viewpoints of integrated physics is an important issue to understand the confinement physics globally. In addition to that, there are international movements towards the integrated numerical simulation study. One is several proposals of integrated modeling of burning tokamak plasmas, motivated by the ITER activity. The integrated numerical simulation will be a good help to draw up new experimental plans especially for burning plasma experiments. Another movement is international collaborations on the confinement database and neoclassical transport in helical plasmas/stellarators. These backgrounds motivate us to start the development of the integrated simulation system which has a modular structure and user-friendly interfaces. The integrated simulation system, which is based on the hierarchical and multi-scale (time and space) modeling, will also be a platform for theoreticians to test their own model such as turbulent transport model. In this paper, we will show the strategy of developing the integrated simulation system and present status of the development. Especially, we discuss the modeling of the time evolution of the plasma net current profile, which is equivalent to the time evolution of the rotational transform profile, in the resistive time scale. (Author)

Retrieval process development and enhancements project Fiscal year 1995: Simulant development technology task progress report

International Nuclear Information System (INIS)

Golcar, G.R.; Bontha, J.R.; Darab, J.G.

1997-01-01

The mission of the Retrieval Process Development and Enhancements (RPD ampersand E) project is to develop an understanding of retrieval processes, including emerging and existing technologies, gather data on these technologies, and relate the data to specific tank problems such that end-users have the requisite technical bases to make retrieval and closure decisions. The development of waste simulants is an integral part of this effort. The work of the RPD ampersand E simulant-development task is described in this document. The key FY95 accomplishments of the RPD ampersand E simulant-development task are summarized below

Development of computational science in JAEA. R and D of simulation

International Nuclear Information System (INIS)

Nakajima, Norihiro; Araya, Fumimasa; Hirayama, Toshio

2006-01-01

R and D of computational science in JAEA (Japan Atomic Energy Agency) is described. Environment of computer, R and D system in CCSE (Center for Computational Science and e-Systems), joint computational science researches in Japan and world, development of computer technologies, the some examples of simulation researches, 3-dimensional image vibrational platform system, simulation researches of FBR cycle techniques, simulation of large scale thermal stress for development of steam generator, simulation research of fusion energy techniques, development of grid computing technology, simulation research of quantum beam techniques and biological molecule simulation researches are explained. Organization of JAEA, development of computational science in JAEA, network of JAEA, international collaboration of computational science, and environment of ITBL (Information-Technology Based Laboratory) project are illustrated. (S.Y.)

RF wave simulation for cold edge plasmas using the MFEM library

Science.gov (United States)

Shiraiwa, S.; Wright, J. C.; Bonoli, P. T.; Kolev, T.; Stowell, M.

2017-10-01

A newly developed generic electro-magnetic (EM) simulation tool for modeling RF wave propagation in SOL plasmas is presented. The primary motivation of this development is to extend the domain partitioning approach for incorporating arbitrarily shaped SOL plasmas and antenna to the TORIC core ICRF solver, which was previously demonstrated in the 2D geometry [S. Shiraiwa, et. al., "HISTORIC: extending core ICRF wave simulation to include realistic SOL plasmas", Nucl. Fusion in press], to larger and more complicated simulations by including a 3D realistic antenna and integrating RF rectified sheath potential model. Such an extension requires a scalable high fidelity 3D edge plasma wave simulation. We used the MFEM [http://mfem.org], open source scalable C++ finite element method library, and developed a Python wrapper for MFEM (PyMFEM), and then a radio frequency (RF) wave physics module in Python. This approach allows for building a physics layer rapidly, while separating the physics implementation being apart from the numerical FEM implementation. An interactive modeling interface was built on pScope [S Shiraiwa, et. al. Fusion Eng. Des. 112, 835] to work with an RF simulation model in a complicated geometry.

Guidelines for developing certification programs for newly generated TRU waste

International Nuclear Information System (INIS)

Whitty, W.J.; Ostenak, C.A.; Pillay, K.K.S.; Geoffrion, R.R.

1983-05-01

These guidelines were prepared with direction from the US Department of Energy (DOE) Transuranic (TRU) Waste Management Program in support of the DOE effort to certify that newly generated TRU wastes meet the Waste Isolation Pilot Plant (WIPP) Waste Acceptance Criteria. The guidelines provide instructions for generic Certification Program preparation for TRU-waste generators preparing site-specific Certification Programs in response to WIPP requirements. The guidelines address all major aspects of a Certification Program that are necessary to satisfy the WIPP Waste Acceptance Criteria and their associated Compliance Requirements and Certification Quality Assurance Requirements. The details of the major element of a Certification Program, namely, the Certification Plan, are described. The Certification Plan relies on supporting data and control documentation to provide a traceable, auditable account of certification activities. Examples of specific parts of the Certification Plan illustrate the recommended degree of detail. Also, a brief description of generic waste processes related to certification activities is included

Newly democratic Mongolia offering exploration contracts

International Nuclear Information System (INIS)

Penttila, W.C.

1992-01-01

This paper reports that Mongolia, formerly the Mongolian People's Republic, is working to open its exploration prospects to international operators as it emerges as the world's 15th largest independent nation. The country, about the same size as Alaska with a population of 2 million, held its first free election in July 1990. The newly elected government drafted a constitution that took effect Feb. 12, 1992. The document modifies the previous government's structures to eliminate bureaucracy and allows for political pluralism. At the same time, the government is formulating energy policies, state oil company structure, and resource development philosophy

Development of a compact nuclear power station engineering simulator

International Nuclear Information System (INIS)

Jian Jianfeng; Yang Yanhua; Lin Meng; Hu Rui

2003-01-01

The compact nuclear power plant project simulator is developed based on the Chashma nuclear power plant. This simulator consists of simulation computation code, data communication module and human-machine interface. This paper discusses the design and implementation of the simulator from such aspect as computer system, hydrothermal model, programming language, human-machine interface and data communication in details

Comparison of a newly developed binary typing with ribotyping and multilocus sequence typing methods for Clostridium difficile.

Science.gov (United States)

Li, Zhirong; Liu, Xiaolei; Zhao, Jianhong; Xu, Kaiyue; Tian, Tiantian; Yang, Jing; Qiang, Cuixin; Shi, Dongyan; Wei, Honglian; Sun, Suju; Cui, Qingqing; Li, Ruxin; Niu, Yanan; Huang, Bixing

2018-04-01

Clostridium difficile is the causative pathogen for antibiotic-related nosocomial diarrhea. For epidemiological study and identification of virulent clones, a new binary typing method was developed for C. difficile in this study. The usefulness of this newly developed optimized 10-loci binary typing method was compared with two widely used methods ribotyping and multilocus sequence typing (MLST) in 189 C. difficile samples. The binary typing, ribotyping and MLST typed the samples into 53 binary types (BTs), 26 ribotypes (RTs), and 33 MLST sequence types (STs), respectively. The typing ability of the binary method was better than that of either ribotyping or MLST expressed in Simpson Index (SI) at 0.937, 0.892 and 0.859, respectively. The ease of testing, portability and cost-effectiveness of the new binary typing would make it a useful typing alternative for outbreak investigations within healthcare facilities and epidemiological research. Copyright © 2018 Elsevier B.V. All rights reserved.

Who Is Doing Well? A Typology of Newly Homeless Adolescents

Science.gov (United States)

Milburn, Norweeta; Liang, Li-Jung; Lee, Sung-Jae; Rotheram-Borus, Mary Jane; Rosenthal, Doreen; Mallett, Shelley; Lightfoot, Marguerita; Lester, Patricia

2009-01-01

There is growing evidence to support developing new typologies for homeless adolescents. Current typologies focus on the risks associated with being homeless, with less consideration of the positive attributes of homeless adolescents. The authors examined both risk and protective factors in a sample of newly homeless adolescents. Using cluster…

Lean Development with the Morpheus Simulation Software

Science.gov (United States)

Brogley, Aaron C.

2013-01-01

The Morpheus project is an autonomous robotic testbed currently in development at NASA's Johnson Space Center (JSC) with support from other centers. Its primary objectives are to test new 'green' fuel propulsion systems and to demonstrate the capability of the Autonomous Lander Hazard Avoidance Technology (ALHAT) sensor, provided by the Jet Propulsion Laboratory (JPL) on a lunar landing trajectory. If successful, these technologies and lessons learned from the Morpheus testing cycle may be incorporated into a landing descent vehicle used on the moon, an asteroid, or Mars. In an effort to reduce development costs and cycle time, the project employs lean development engineering practices in its development of flight and simulation software. The Morpheus simulation makes use of existing software packages where possible to reduce the development time. The development and testing of flight software occurs primarily through the frequent test operation of the vehicle and incrementally increasing the scope of the test. With rapid development cycles, risk of loss of the vehicle and loss of the mission are possible, but efficient progress in development would not be possible without that risk.

Newly graduated nurses' empowerment regarding professional competence and other work-related factors.

Science.gov (United States)

Kuokkanen, Liisa; Leino-Kilpi, Helena; Numminen, Olivia; Isoaho, Hannu; Flinkman, Mervi; Meretoja, Riitta

2016-01-01

Although both nurse empowerment and competence are fundamental concepts of describing newly graduated nurses' professional development and job satisfaction, only few studies exist on the relationship between these concepts. Therefore, the purpose of this study was to determine how newly graduated nurses assess their empowerment and to clarify professional competence compared to other work-related factors. A descriptive, cross-sectional and correlational design was applied. The sample comprised newly graduated nurses (n = 318) in Finland. Empowerment was measured using the 19-item Qualities of an Empowered Nurse scale and the Nurse Competence Scale measured nurses' self-assessed generic competence. In addition to demographic data, the background data included employment sector (public/private), job satisfaction, intent to change/leave job, work schedule (shifts/business hours) and assessments of the quality of care in the workplace. The data were analysed statistically by using Spearman's correlation coefficient as well as the One-Way and Multivariate Analysis of Variance. Cronbach's alpha coefficient was used to estimate the internal consistency. Newly graduated nurses perceived their level of empowerment and competence fairly high. The association between nurse empowerment and professional competence was statistically significant. Other variables correlating positively to empowerment included employment sector, age, job satisfaction, intent to change job, work schedule, and satisfaction with the quality of care in the work unit. The study indicates competence had the strongest effect on newly graduated nurses' empowerment. New graduates need support and career opportunities. In the future, nurses' further education and nurse managers' resources for supporting and empowering nurses should respond to the newly graduated nurses' requisites for attractive and meaningful work.

A simulation environment for ITER PCS development

International Nuclear Information System (INIS)

Walker, M.L.; Ambrosino, G.; De Tommasi, G.; Humphreys, D.A.; Mattei, M.; Neu, G.; Raupp, G.; Treutterer, W.; Winter, A.

2014-01-01

Highlights: • Describes task to develop simulation tool to aid development/testing of ITER PCS. • Requirements and use cases and preliminary architecture have been delivered. • Detailed design is now being developed. • Provides overview of use cases and requirements. • Provides overview of architecture and status of development. - Abstract: A simulation environment known as the Plasma Control System Simulation Platform (PCSSP), specifically designed to support development of the ITER Plasma Control System (PCS), is currently under construction by an international team encompassing a cross-section of expertise in simulation and exception handling for plasma control. The proposed design addresses the challenging requirements of supporting the PCS design. This paper provides an overview of the PCSSP project and a discussion of some of the major features of its design. Plasma control for the ITER tokamak will be significantly more challenging than for existing fusion devices. An order of magnitude greater performance (e.g. [1,2]) is needed for some types of control, which together with limited actuator authority, implies that optimized individual controllers and nonlinear saturation logic are required. At the same time, consequences of control failure are significantly more severe, which implies a conflicting requirement for robust control. It also implies a requirement for comprehensive and robust exception handling. Coordinated control of multiple competing objectives with significant interactions, together with many shared uses of actuators to control multiple variables, implies that highly integrated control logic and shared actuator management will be required. It remains a challenge for the integrated technologies to simultaneously address these multiple and often competing requirements to be demonstrated on existing fusion devices and adapted for ITER in time to support its operational schedule. We describe ways in which the PCSSP will help address

Adapted to change: The rapid development of symbiosis in newly settled, fast-maturing chemosymbiotic mussels in the deep sea.

Science.gov (United States)

Laming, Sven R; Duperron, Sébastien; Gaudron, Sylvie M; Hilário, Ana; Cunha, Marina R

2015-12-01

Symbioses between microbiota and marine metazoa occur globally at chemosynthetic habitats facing imminent threat from anthropogenic disturbance, yet little is known concerning the role of symbiosis during early development in chemosymbiotic metazoans: a critical period in any benthic species' lifecycle. The emerging symbiosis of Idas (sensu lato) simpsoni mussels undergoing development is assessed over a post-larval-to-adult size spectrum using histology and fluorescence in situ hybridisation (FISH). Post-larval development shows similarities to that of both heterotrophic and chemosymbiotic mussels. Data from newly settled specimens confirm aposymbiotic, planktotrophic larval development. Sulphur-oxidising (SOX) symbionts subsequently colonise multiple exposed, non-ciliated epithelia shortly after metamorphosis, but only become abundant on gills as these expand with greater host size. This wide-spread bathymodiolin recorded from sulphidic wood, bone and cold-seep habitats, displays a suite of adaptive traits that could buffer against anthropogenic disturbance. Copyright © 2015 Elsevier Ltd. All rights reserved.

Foundational Elements of Applied Simulation Theory: Development and Implementation of a Longitudinal Simulation Educator Curriculum.

Science.gov (United States)

Chiu, Michelle; Posner, Glenn; Humphrey-Murto, Susan

2017-01-27

Simulation-based education has gained popularity, yet many faculty members feel inadequately prepared to teach using this technique. Fellowship training in medical education exists, but there is little information regarding simulation or formal educational programs therein. In our institution, simulation fellowships were offered by individual clinical departments. We recognized the need for a formal curriculum in educational theory. Kern's approach to curriculum development was used to develop, implement, and evaluate the Foundational Elements of Applied Simulation Theory (FEAST) curriculum. Needs assessments resulted in a 26-topic curriculum; each biweekly session built upon the previous. Components essential to success included setting goals and objectives for each interactive session and having dedicated faculty, collaborative leadership and administrative support for the curriculum. Evaluation data was collated and analyzed annually via anonymous feedback surveys, focus groups, and retrospective pre-post self-assessment questionnaires. Data collected from 32 fellows over five years of implementation showed that the curriculum improved knowledge, challenged thinking, and was excellent preparation for a career in simulation-based medical education. Themes arising from focus groups demonstrated that participants valued faculty expertise and the structure, practicality, and content of the curriculum. We present a longitudinal simulation educator curriculum that adheres to a well-described framework of curriculum development. Program evaluation shows that FEAST has increased participant knowledge in key areas relevant to simulation-based education and that the curriculum has been successful in meeting the needs of novice simulation educators. Insights and practice points are offered for educators wishing to implement a similar curriculum in their institution.

Dynamic simulation of sustainable farm development scenarios using cognitive modeling

Directory of Open Access Journals (Sweden)

Tuzhyk Kateryna

2017-03-01

Full Text Available Dynamic simulation of sustainable farm development scenarios using cognitive modeling. The paper presents a dynamic simulation system of sustainable development scenarios on farms using cognitive modeling. The system incorporates relevant variables which affect the sustainable development of farms. Its user provides answers to strategic issues connected with the level of farm sustainability over a long-term perspective of dynamic development. The work contains a description of the model structure as well as the results of simulations carried out on 16 farms in northern Ukraine. The results show that the process of sustainability is based mainly on the potential for innovation in agricultural production and biodiversity. The user is able to simulate various scenarios for the sustainable development of a farm and visualize the influence of factors on the economic and social situation, as well as on environmental aspects. Upon carrying out a series of simulations, it was determined that the development of farms characterized by sustainable development is based on additional profit, which serves as the main motivation for transforming a conventional farm into a sustainable one. Nevertheless, additional profit is not the only driving force in the system of sustainable development. The standard of living, market condition, and legal regulations as well as government support also play a significant motivational role.

Newly developed low-temperature scanning tunneling microscope and its application to the study of superconducting materials

International Nuclear Information System (INIS)

Gao, F.; Dai, C.; Chen, Z.; Huang, G.; Bai, C.; Tao, H.; Yin, B.; Yang, Q.; Zhao, Z.

1994-01-01

A newly developed scanning tunneling microscope (STM) capable of operating at room temperature, 77 K, and 4.2 K is presented. This compact STM has a highly symmetric and rigid tunneling unit designed as an integral frame except the coarse and fine adjustment parts. The tunneling unit is incorporated into a small vacuum chamber that is usually pumped down to 2x10 -4 Pa to avoid water contamination. The fine mechanic adjustment makes the tip approach the sample in 5 nm steps. The coarse adjustment not only changes the distance between the tip and the sample, but also adjusts the tip to be normal to the surface of the sample. With this low-temperature STM atomic resolution images of Bi-2212 single-crystal and large-scale topographies of a YBa 2 Cu 3 O 7 thin film are observed at 77 K

Development of a safety and regulation systems simulation program II

International Nuclear Information System (INIS)

1985-05-01

This report describes the development of a safety and regulation systems simulation program under contract to the Atomic Energy Control Board of Canada. A systems logic interaction simulation (SLISIM) program was developed for the AECB's HP-1000 computer which operates in the interactive simulation (INSIM) program environment. The SLISIM program simulates the spatial neutron dynamics, the regulation of the reactor power and in this version the CANDU-PHW 600 MW(e) computerized shutdown systems' trip parameters. The modular concept and interactive capability of the INSIM environment provides the user with considerable flexibility of the setup and control of the simulation

A new simulation method for turbines in wake - Applied to extreme response during operation

DEFF Research Database (Denmark)

Thomsen, K.; Aagaard Madsen, H.

2005-01-01

The work focuses on prediction of load response for wind turbines operating in wind forms using a newly developed aeroelostic simulation method The traditionally used concept is to adjust the free flow turbulence intensity to account for increased loads in wind farms-a methodology that might......, the resulting extremes might be erroneous. For blade loads the traditionally used simplified approach works better than for integrated rotor loads-where the instantaneous load gradient across the rotor disc is causing the extreme loads. In the article the new wake simulation approach is illustrated...

Development of an educational nuclear research reactor simulator

International Nuclear Information System (INIS)

Arafa, Amany Abdel Aziz; Saleh, Hassan Ibrahim; Ashoub, Nagieb

2014-01-01

This paper introduces the development of a research reactor educational simulator based on LabVIEW that allows the training of operators and studying different accident scenarios and the effects of operational parameters on the reactor behavior. Using this simulator, the trainee can test the interaction between the input parameters and the reactor activities. The LabVIEW acts as an engine implements the reactor mathematical models. In addition, it is used as a tool for implementing the animated graphical user interface. This simulator provides the training requirements for both of the reactor staff and the nuclear engineering students. Therefore, it uses dynamic animation to enhance learning and interest for a trainee on real system problems and provides better visual effects, improved communications, and higher interest levels. The benefits of conducting such projects are to develop the expertise in this field and save costs of both operators training and simulation courses.

Development of an educational nuclear research reactor simulator

Energy Technology Data Exchange (ETDEWEB)

Arafa, Amany Abdel Aziz; Saleh, Hassan Ibrahim [Atomic Energy Authority, Cairo (Egypt). Radiation Engineering Dept.; Ashoub, Nagieb [Atomic Energy Authority, Cairo (Egypt). Reactor Physics Dept.

2014-12-15

This paper introduces the development of a research reactor educational simulator based on LabVIEW that allows the training of operators and studying different accident scenarios and the effects of operational parameters on the reactor behavior. Using this simulator, the trainee can test the interaction between the input parameters and the reactor activities. The LabVIEW acts as an engine implements the reactor mathematical models. In addition, it is used as a tool for implementing the animated graphical user interface. This simulator provides the training requirements for both of the reactor staff and the nuclear engineering students. Therefore, it uses dynamic animation to enhance learning and interest for a trainee on real system problems and provides better visual effects, improved communications, and higher interest levels. The benefits of conducting such projects are to develop the expertise in this field and save costs of both operators training and simulation courses.

Computer simulation of aqueous Na-Cl electrolytes

Energy Technology Data Exchange (ETDEWEB)

Hummer, G. [Los Alamos National Lab., NM (United States); Soumpasis, D.M. [Max-Planck-Institut fuer Biophysikalische Chemie (Karl-Friedrich-Bonhoeffer-Institut), Goettingen (Germany); Neumann, M. [Vienna Univ. (Austria). Inst. fuer Experimentalphysik

1993-11-01

Equilibrium structure of aqueous Na-Cl electrolytes between 1 and 5 mol/l is studied by means of molecular dynamics computer simulation using interaction site descriptions of water and ionic components. Electrostatic interactions are treated both with the newly developed charged-clouds scheme and with Ewald summation. In the case of a 5 mol/l electrolyte, the results for pair correlations obtained by the two methods are in excellent agreement. However, the charged-clouds technique is much faster than Ewald summation and makes simulations at lower salt concentrations feasible. It is found that both ion-water and ion-ion correlation functions depend only weakly on the ionic concentration. Sodium and chloride ions exhibit only a negligible tendency to form contact pairs. In particular, no chloride ion pairs in contact are observed.

Computer simulation of aqueous Na-Cl electrolytes

International Nuclear Information System (INIS)

Hummer, G.; Soumpasis, D.M.; Neumann, M.

1993-01-01

Equilibrium structure of aqueous Na-Cl electrolytes between 1 and 5 mol/l is studied by means of molecular dynamics computer simulation using interaction site descriptions of water and ionic components. Electrostatic interactions are treated both with the newly developed charged-clouds scheme and with Ewald summation. In the case of a 5 mol/l electrolyte, the results for pair correlations obtained by the two methods are in excellent agreement. However, the charged-clouds technique is much faster than Ewald summation and makes simulations at lower salt concentrations feasible. It is found that both ion-water and ion-ion correlation functions depend only weakly on the ionic concentration. Sodium and chloride ions exhibit only a negligible tendency to form contact pairs. In particular, no chloride ion pairs in contact are observed

Beam Delivery Simulation - Recent Developments and Optimization

CERN Document Server

AUTHOR|(INSPIRE)INSPIRE-00232566; Boogert, Stewart Takashi; Garcia-Morales, H; Gibson, Stephen; Kwee-Hinzmann, Regina; Nevay, Laurence James; Deacon, Lawrence Charles

2015-01-01

Beam Delivery Simulation (BDSIM) is a particle tracking code that simulates the passage of particles through both the magnetic accelerator lattice as well as their interaction with the material of the accelerator itself. The Geant4 toolkit is used to give a full range of physics processes needed to simulate both the interaction of primary particles and the production and subsequent propagation of secondaries. BDSIM has already been used to simulate linear accelerators such as the International Linear Collider (ILC) and the Compact Linear Collider (CLIC), but it has recently been adapted to simulate circular accelerators as well, producing loss maps for the Large Hadron Collider (LHC). In this paper the most recent developments, which extend BDSIM’s functionality as well as improve its efficiency are presented. Improvement and refactorisation of the tracking algorithms are presented alongside improved automatic geometry construction for increased particle tracking speed.

Feasibility and preliminary effects of an intervention targeting schema development for caregivers of newly admitted hospice patients.

Science.gov (United States)

Lindstrom, Kathryn B; Mazurek Melnyk, Bernadette

2013-06-01

The transition to hospice care is a stressful experience for caregivers, who report high anxiety, unpreparedness, and lack of confidence. These sequelae are likely explained by the lack of an accurate cognitive schema, not knowing what to expect or how to help their loved one. Few interventions exist for this population and most do not measure preparedness, confidence, and anxiety using a schema building a conceptual framework for a new experience. The purpose of this study was to test the feasibility and preliminary effects of an intervention program, Education and Skill building Intervention for Caregivers of Hospice patients (ESI-CH), using an innovative conceptual design that targets cognitive schema development and basic skill building for caregivers of loved ones newly admitted to hospice services. A pre-experimental one-group pre- and post-test study design was used. Eighteen caregivers caring for loved ones in their homes were recruited and twelve completed the pilot study. Depression, anxiety, activity restriction, preparedness, and beliefs/confidence were measured. Caregivers reported increased preparedness, more helpful beliefs, and more confidence about their ability to care for their loved one. Preliminary trends suggested decreased anxiety levels for the intervention group. Caregivers who completed the intervention program rated the program very good or excellent, thought the information was helpful and timely, and would recommend it to friends. Results show promise that the ESI-CH program may assist as an evidence-based program to support caregivers in their role as a caregiver to a newly admitted hospice patient.

Recent developments in numerical simulation techniques of thermal recovery processes

Energy Technology Data Exchange (ETDEWEB)

Tamim, M. [Bangladesh University of Engineering and Technology, Bangladesh (Bangladesh); Abou-Kassem, J.H. [Chemical and Petroleum Engineering Department, UAE University, Al-Ain 17555 (United Arab Emirates); Farouq Ali, S.M. [University of Alberta, Alberta (Canada)

2000-05-01

Numerical simulation of thermal processes (steam flooding, steam stimulation, SAGD, in-situ combustion, electrical heating, etc.) is an integral part of a thermal project design. The general tendency in the last 10 years has been to use commercial simulators. During the last decade, only a few new models have been reported in the literature. More work has been done to modify and refine solutions to existing problems to improve the efficiency of simulators. The paper discusses some of the recent developments in simulation techniques of thermal processes such as grid refinement, grid orientation, effect of temperature on relative permeability, mathematical models, and solution methods. The various aspects of simulation discussed here promote better understanding of the problems encountered in the simulation of thermal processes and will be of value to both simulator users and developers.

Experimental validation of a rapid Monte Carlo based micro-CT simulator

International Nuclear Information System (INIS)

Colijn, A P; Zbijewski, W; Sasov, A; Beekman, F J

2004-01-01

We describe a newly developed, accelerated Monte Carlo simulator of a small animal micro-CT scanner. Transmission measurements using aluminium slabs are employed to estimate the spectrum of the x-ray source. The simulator incorporating this spectrum is validated with micro-CT scans of physical water phantoms of various diameters, some containing stainless steel and Teflon rods. Good agreement is found between simulated and real data: normalized error of simulated projections, as compared to the real ones, is typically smaller than 0.05. Also the reconstructions obtained from simulated and real data are found to be similar. Thereafter, effects of scatter are studied using a voxelized software phantom representing a rat body. It is shown that the scatter fraction can reach tens of per cents in specific areas of the body and therefore scatter can significantly affect quantitative accuracy in small animal CT imaging

Status of development on simulation technology for pyrochemical reprocessing

International Nuclear Information System (INIS)

Arie, Kazuo; Mizuguchi, Koji; Fujita, Reiko

2004-01-01

Simulation techniques for the elemental behaviors in the pyrochemical reprocessing process of spent nuclear fuels are important for fuel reprocessing and future power station development. The authors developed a simulation code SPR1.0 which can analyze co-occurring electrochemical and chemical reactions simultaneously and which is applicable to know the behavior of any element in the system. The present report describes the status of the code development, the database for fundamental electrochemical reactions, and verification of the code. The code employs TRIAS code for electrochemical reactions and SOLGASMIX-PV for chemical reactions. Electrolytic process for MOX (mixed oxide) fuels with different Pu redox ratios were simulated using the present code and the effect of introducing iron ions was studied. The prospect of future development is also described. (S. Ohno)

Fluorescent and radiolabelling of pepsin-digested human glomerular basement membrane with a newly developed hydroxy-coumarin derivative (CASE)

International Nuclear Information System (INIS)

Rand-Weaver, M.; Abuknesha, R.A.; Price, R.G.

1985-01-01

The labelling of pepsin-digested human glomerular basement membrane (pHGBM) with a newly developed fluorescent iodine acceptor 7-hydroxy-coumarin-3-acetic acid N-hydroxysucciniimydyl ester (CASE) is described. The binding of a monoclonal antibody to pHGBM was assessed by radiobinding assays, and when directly iodinated pHGBM was used there was no apparent binding. When CASE was conjugated to pHGBM prior to iodination 11% binding was achieved. CASE acting as an iodine acceptor may be useful for proteins containing few or inaccessible tyrosine residues or which are destroyed by introduction of 125 I. Since CASE is fluorescent, small amounts of material can be detected during isolation prior to iodination. (orig.)

Proceedings of eSim 2006 : IBPSA-Canada's 4. biennial building performance simulation conference

International Nuclear Information System (INIS)

Kesik, T.

2006-01-01

This conference was attended by professionals, academics and students interested in promoting the science of building performance simulation in order to optimize design, construction, operation and maintenance of new and existing buildings around the world. This biennial conference and exhibition covered all topics related to computerized simulation of a building's energy performance and energy efficiency. Computerized simulation is widely used to predict the environmental performance of buildings during all stages of a building's life cycle, from the design, commissioning, construction, occupancy and management stages. Newly developed simulation methods for optimal comfort in new and existing buildings were evaluated. The themes of the conference were: recent developments for modelling the physical processes relevant to buildings; algorithms for modelling conventional and innovative HVAC systems; methods for modelling whole-building performance; building simulation software development; the use of building simulation tools in code compliance; moving simulation into practice; validation of building simulation software; architectural design; and optimization approaches in building design. The conference also covered the modeling of energy supply systems with reference to renewable energy sources such as ground source heat pumps or hybrid systems incorporating solar energy. The conference featured 32 presentations, of which 28 have been catalogued separately for inclusion in this database. refs., tabs., figs

Final Stage Development of Reactor Console Simulator

International Nuclear Information System (INIS)

Mohamad Idris Taib; Ridzuan Abdul Mutalib; Zareen Khan Abdul Jalil Khan; Mohd Khairulezwan Abdul Manan; Mohd Sabri Minhat; Nurfarhana Ayuni Joha

2013-01-01

The Reactor Console Simulator PUSPATI TRIGA Reactor was developed since end of 2011 and now in the final stage of development. It is will be an interactive tool for operator training and teaching of PUSPATI TRIGA Reactor. Behavior and characteristic for reactor console and reactor itself can be evaluated and understand. This Simulator will be used as complement for actual present reactor console. Implementation of human system interface (HSI) is using computer screens, keyboard and mouse. Multiple screens are used to match the physical of present reactor console. LabVIEW software are using for user interface and mathematical calculation. Polynomial equation based on control rods calibration data as well as operation parameters record was used to calculate and estimated reactor console parameters. The capabilities in user interface, reactor physics and thermal-hydraulics can be expanded and explored to simulation as well as modeling for New Reactor Console, Research Reactor and Nuclear Power Plant. (author)

URDME: a modular framework for stochastic simulation of reaction-transport processes in complex geometries.

Science.gov (United States)

Drawert, Brian; Engblom, Stefan; Hellander, Andreas

2012-06-22

Experiments in silico using stochastic reaction-diffusion models have emerged as an important tool in molecular systems biology. Designing computational software for such applications poses several challenges. Firstly, realistic lattice-based modeling for biological applications requires a consistent way of handling complex geometries, including curved inner- and outer boundaries. Secondly, spatiotemporal stochastic simulations are computationally expensive due to the fast time scales of individual reaction- and diffusion events when compared to the biological phenomena of actual interest. We therefore argue that simulation software needs to be both computationally efficient, employing sophisticated algorithms, yet in the same time flexible in order to meet present and future needs of increasingly complex biological modeling. We have developed URDME, a flexible software framework for general stochastic reaction-transport modeling and simulation. URDME uses Unstructured triangular and tetrahedral meshes to resolve general geometries, and relies on the Reaction-Diffusion Master Equation formalism to model the processes under study. An interface to a mature geometry and mesh handling external software (Comsol Multiphysics) provides for a stable and interactive environment for model construction. The core simulation routines are logically separated from the model building interface and written in a low-level language for computational efficiency. The connection to the geometry handling software is realized via a Matlab interface which facilitates script computing, data management, and post-processing. For practitioners, the software therefore behaves much as an interactive Matlab toolbox. At the same time, it is possible to modify and extend URDME with newly developed simulation routines. Since the overall design effectively hides the complexity of managing the geometry and meshes, this means that newly developed methods may be tested in a realistic setting already at

Dr.LiTHO: a development and research lithography simulator

Science.gov (United States)

Fühner, Tim; Schnattinger, Thomas; Ardelean, Gheorghe; Erdmann, Andreas

2007-03-01

This paper introduces Dr.LiTHO, a research and development oriented lithography simulation environment developed at Fraunhofer IISB to flexibly integrate our simulation models into one coherent platform. We propose a light-weight approach to a lithography simulation environment: The use of a scripting (batch) language as an integration platform. Out of the great variety of different scripting languages, Python proved superior in many ways: It exhibits a good-natured learning-curve, it is efficient, available on virtually any platform, and provides sophisticated integration mechanisms for existing programs. In this paper, we will describe the steps, required to provide Python bindings for existing programs and to finally generate an integrated simulation environment. In addition, we will give a short introduction into selected software design demands associated with the development of such a framework. We will especially focus on testing and (both technical and user-oriented) documentation issues. Dr.LiTHO Python files contain not only all simulation parameter settings but also the simulation flow, providing maximum flexibility. In addition to relatively simple batch jobs, repetitive tasks can be pooled in libraries. And as Python is a full-blown programming language, users can add virtually any functionality, which is especially useful in the scope of simulation studies or optimization tasks, that often require masses of evaluations. Furthermore, we will give a short overview of the numerous existing Python packages. Several examples demonstrate the feasibility and productiveness of integrating Python packages into custom Dr.LiTHO scripts.

Development of a Desktop Simulator for APR1400 Nuclear Power Plant

International Nuclear Information System (INIS)

Lee, J. B.

2016-01-01

It is essential for utilities to possess a full-scope simulator for operator training and operation test for operators. But it is very expensive and sometimes lack of fidelity if processes of developing the simulator and designing the plant are in parallel. It is due to the situation that simulator development stage sometimes precedes the plant design stage and modifications may occur to the design of the plant in construction stage. In an attempt to build a low cost and efficient simulator, a desktop simulator has been developed. This model is described herein. Using desktop simulators for training operators is an efficient method for familiarizing operators with their plant’s operation. A low cost and efficient desktop simulator for APR1400 has been developed, and brief features are introduced here. It is configured to mimic a full-scale simulator, and can be used for operators to be familiarized to their plant’s operation. Since the size of the simulator is small enough to be fit in a desk, it can be used in a classroom or in an office at any time. It can also be used to evaluate design changes or modifications of the plant before implementing them to the plant

Development of a Desktop Simulator for APR1400 Nuclear Power Plant

Energy Technology Data Exchange (ETDEWEB)

Lee, J. B. [KHNP Central Research Institute, Daejeon (Korea, Republic of)

2016-10-15

It is essential for utilities to possess a full-scope simulator for operator training and operation test for operators. But it is very expensive and sometimes lack of fidelity if processes of developing the simulator and designing the plant are in parallel. It is due to the situation that simulator development stage sometimes precedes the plant design stage and modifications may occur to the design of the plant in construction stage. In an attempt to build a low cost and efficient simulator, a desktop simulator has been developed. This model is described herein. Using desktop simulators for training operators is an efficient method for familiarizing operators with their plant’s operation. A low cost and efficient desktop simulator for APR1400 has been developed, and brief features are introduced here. It is configured to mimic a full-scale simulator, and can be used for operators to be familiarized to their plant’s operation. Since the size of the simulator is small enough to be fit in a desk, it can be used in a classroom or in an office at any time. It can also be used to evaluate design changes or modifications of the plant before implementing them to the plant.

Development and Implementation of Mechanistic Terry Turbine Models in RELAP-7 to Simulate RCIC Normal Operation Conditions

Energy Technology Data Exchange (ETDEWEB)

Zhao, Haihua [Idaho National Lab. (INL), Idaho Falls, ID (United States); Zou, Ling [Idaho National Lab. (INL), Idaho Falls, ID (United States); Zhang, Hongbin [Idaho National Lab. (INL), Idaho Falls, ID (United States); O' Brien, James Edward [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2016-09-01

As part of the efforts to understand the unexpected “self-regulating” mode of the RCIC (Reactor Core Isolation Cooling) systems in Fukushima accidents and extend BWR RCIC and PWR AFW (Auxiliary Feed Water) operational range and flexibility, mechanistic models for the Terry turbine, based on Sandia’s original work [1], have been developed and implemented in the RELAP-7 code to simulate the RCIC system. In 2016, our effort has been focused on normal working conditions of the RCIC system. More complex off-design conditions will be pursued in later years when more data are available. In the Sandia model, the turbine stator inlet velocity is provided according to a reduced-order model which was obtained from a large number of CFD (computational fluid dynamics) simulations. In this work, we propose an alternative method, using an under-expanded jet model to obtain the velocity and thermodynamic conditions for the turbine stator inlet. The models include both an adiabatic expansion process inside the nozzle and a free expansion process outside of the nozzle to ambient pressure. The combined models are able to predict the steam mass flow rate and supersonic velocity to the Terry turbine bucket entrance, which are the necessary input information for the Terry turbine rotor model. The analytical models for the nozzle were validated with experimental data and benchmarked with CFD simulations. The analytical models generally agree well with the experimental data and CFD simulations. The analytical models are suitable for implementation into a reactor system analysis code or severe accident code as part of mechanistic and dynamical models to understand the RCIC behaviors. The newly developed nozzle models and modified turbine rotor model according to the Sandia’s original work have been implemented into RELAP-7, along with the original Sandia Terry turbine model. A new pump model has also been developed and implemented to couple with the Terry turbine model. An input

Development of module-based simulation system for nuclear power plant

International Nuclear Information System (INIS)

Yoshikawa, H.

1990-01-01

Module-based Simulation System (MSS) has been developed to realize a new software environment enabling versatile dynamic simulation of a complex nuclear power plant system flexibly. Described in the paper are (i) fundamental methods utilized in MMS and its software systemization, (ii) development of human interface system to help users in generating integrated simulation programs automatically, and (iii) development of an intelligent user support system for helping users in the two phases of automatical semantic diagnosis and consultation to automatic input data setup for the MSS-generated programs

Development of NSSS Simulation Engine for SMART Simulator Using the Best Estimate Code, MARS3.1

International Nuclear Information System (INIS)

Kim, K. D.; Lee, S. W.; Lee, Sung Chul; Suh, Yong Suk; Suh, Jae Seung

2011-01-01

Limited computational capability and crude thermalhydraulic modeling in early 1980s forced the use of overly simplified physical models and assumptions for a real-time calculation at the cost of fidelity. Rapid advances in computer technology make it possible to improve the fidelity of the simulator models. These efforts have been made based on RELAP5 in the US, and CATHARE2 in France. The NSSS thermalhydraulic engines adopted in the most domestic fullscope power plant simulators have been replaced with RELAP5 based engines which were provided by US vendors. Since the technology dependency of the NSSS T/H engine by foreign vendors, it may cause difficulties in maintenance and model improvement. KAERI has started to develop a realistic NSSS calculation engine based on the best-estimate code MARS 3.1 for the SMART full-scope simulator. Even though we are developing the NSSS calculation engine for SMART simulator, it can be easily extended to light water reactors and GEN-IV reactors, etc. The verification of the NSSS calculation engine for SMART simulator has been conducted by an integrated test in the simulator environment, Jade 4.0, developed by GSE of Windows 2003. This paper briefly presents our efforts for the NSSS calculation engine for SMART simulator and verification test results of SAT (Site Acceptance Test)

Development of a Persistent Chemical Agent Simulator System (PCASS)

Science.gov (United States)

Mcginness, W. G.

1983-01-01

The development of a persistent chemical agent simulation system (PCASS) is described. This PCASS is to be used for the military training of troops to simulate actual chemical warfare. The purpose of this system is to facilitate in the determination of chemical contamination and effectiveness of decontamination for training purposes. The fluorescent tracer employed has no daylight activation, but yet is easily removed with a decontaminate solution or water and surfactants. Also employed is a time delayed color developing system. When an individual is subjected to the PCASS and does not decontaminate adequately, red blotches or red coloration will develop as a function of time and temperature. The intent of this is to simulate the delayed chemical reaction of mustard contaminates.

Critical thinking dispositions among newly graduated nurses

Science.gov (United States)

Wangensteen, Sigrid; Johansson, Inger S; Björkström, Monica E; Nordström, Gun

2010-01-01

wangensteen s., johansson i.s., björkström m.e. & nordström g. (2010) Critical thinking dispositions among newly graduated nurses. Journal of Advanced Nursing66(10), 2170–2181. Aim The aim of the study was to describe critical thinking dispositions among newly graduated nurses in Norway, and to study whether background data had any impact on critical thinking dispositions. Background Competence in critical thinking is one of the expectations of nursing education. Critical thinkers are described as well-informed, inquisitive, open-minded and orderly in complex matters. Critical thinking competence has thus been designated as an outcome for judging the quality of nursing education programmes and for the development of clinical judgement. The ability to think critically is also described as reducing the research–practice gap and fostering evidence-based nursing. Methods A cross-sectional descriptive study was performed. The data were collected between October 2006 and April 2007 using the California Critical Thinking Disposition Inventory. The response rate was 33% (n= 618). Pearson’s chi-square tests were used to analyse the data. Results Nearly 80% of the respondents reported a positive disposition towards critical thinking. The highest mean score was on the Inquisitiveness subscale and the lowest on the Truth-seeking subscale. A statistically significant higher proportion of nurses with high critical thinking scores were found among those older than 30 years, those with university education prior to nursing education, and those working in community health care. Conclusion Nurse leaders and nurse teachers should encourage and nurture critical thinking among newly graduated nurses and nursing students. The low Truth-seeking scores found may be a result of traditional teaching strategies in nursing education and might indicate a need for more student-active learning models. PMID:20384637

SINERGIA laparoscopic virtual reality simulator: didactic design and technical development.

Science.gov (United States)

Lamata, Pablo; Gómez, Enrique J; Sánchez-Margallo, Francisco M; López, Oscar; Monserrat, Carlos; García, Verónica; Alberola, Carlos; Florido, Miguel Angel Rodríguez; Ruiz, Juan; Usón, Jesús

2007-03-01

VR laparoscopic simulators have demonstrated its validity in recent studies, and research should be directed towards a high training effectiveness and efficacy. In this direction, an insight into simulators' didactic design and technical development is provided, by describing the methodology followed in the building of the SINERGIA simulator. It departs from a clear analysis of training needs driven by a surgical training curriculum. Existing solutions and validation studies are an important reference for the definition of specifications, which are described with a suitable use of simulation technologies. Five new didactic exercises are proposed to train some of the basic laparoscopic skills. Simulator construction has required existing algorithms and the development of a particle-based biomechanical model, called PARSYS, and a collision handling solution based in a multi-point strategy. The resulting VR laparoscopic simulator includes new exercises and enhanced simulation technologies, and is finding a very good acceptance among surgeons.

Planning for the Management and Disposition of Newly Generated TRU Waste from REDC

International Nuclear Information System (INIS)

Coffey, D. E.; Forrester, T. W.; Krause, T.

2002-01-01

This paper describes the waste characteristics of newly generated transuranic waste from the Radiochemical Engineering and Development Center at the Oak Ridge National Laboratory and the basic certification structure that will be proposed by the University of Tennessee-Battelle and Bechtel Jacobs Company LLC to the Waste Isolation Pilot Plant for this waste stream. The characterization approach uses information derived from the active production operations as acceptable knowledge for the Radiochemical Engineering and Development Center transuranic waste. The characterization approach includes smear data taken from processing and waste staging hot cells, as well as analytical data on product and liquid waste streams going to liquid waste disposal. Bechtel Jacobs Company and University of Tennessee-Battelle are currently developing the elements of a Waste Isolation Pilot Plant-compliant program with a plan to be certified by the Waste Isolation Pilot Plant for shipment of newly generated transuranic waste in the next few years. The current activities include developing interface plans, program documents, and waste stream specific procedures

Simulation of erosion in drilling tools for oil and gas industry

Energy Technology Data Exchange (ETDEWEB)

Arefi, B.; Settari, A. [Calgary Univ., AB (Canada); Angman, P. [Tesco Corp., Calgary, AB (Canada)

2004-07-01

Erosion in oil well drilling tools is a form of wear which occurs when fluid containing solid particles impacts a solid surface. The intensity of erosion is generally measured as the rate of material removal from the surface, and is expressed as E{sub r}, the weight of material removed by unit weight of impacting particles. Erosion can also be reduced by tool improvement and modification, thereby extending the life of drilling tools. To date, no attempt has been made to model the erosion phenomenon in drilling tools. This paper presents a newly developed erosion simulator which is the first design tool for the drilling industry. This work demonstrates that erosion can be simulated. A model was developed to calibrate the erosion coefficients for drilling tool conditions. The mechanism of erosion can be controlled by the impact velocity and angle. Algorithms were developed for transient simulation of the erosion of any surface in 2-dimensional geometry. The Erosion Simulator has been validated and calibrated against data provided by TESCO Corporation's casing drilling tools. The model has been shown to successfully predict and minimize erosion by modifying the tool geometry and metallurgy. 21 refs., 1 tab., 15 figs.

Simulation of an advanced small aperture track system

Science.gov (United States)

Williams, Tommy J.; Crockett, Gregg A.; Brunson, Richard L.; Beatty, Brad; Zahirniak, Daniel R.; Deuto, Bernard G.

2001-08-01

Simulation development for EO Systems has progressed to new levels with the advent of COTS software tools such as Matlab/Simulink. These tools allow rapid reuse of simulation library routines. We have applied these tools to newly emerging Acquisition Tracking and Pointing (ATP) systems using many routines developed through a legacy to High Energy Laser programs such as AirBorne Laser, Space Based Laser, Tactical High Energy Laser, and The Air Force Research Laboratory projects associated with the Starfire Optical Range. The simulation architecture allows ease in testing various track algorithms under simulated scenes with the ability to rapidly vary system hardware parameters such as track sensor and track loop control systems. The atmospheric turbulence environment and associated optical distortion is simulated to high fidelity levels through the application of an atmospheric phase screen model to produce scintillation of the laser illuminator uplink. The particular ATP system simulated is a small transportable system for tracking satellites in a daytime environment and projects a low power laser and receives laser return from retro-reflector equipped satellites. The primary application of the ATP system (and therefore the simulation) is the determination of the illuminator beam profile, jitter, and scintillation of the low power laser at the satellite. The ATP system will serve as a test bed for satellite tracking in a high background during daytime. Of particular interest in this simulation is the ability to emulate the hardware modelogic within the simulation to test and refine system states and mode change decisions. Additionally, the simulation allows data from the hardware system tests to be imported into Matlab and to thereby drive the simulation or to be easily compared to simulation results.

Optimization and Simulation in Drug Development - Review and Analysis

DEFF Research Database (Denmark)

Schjødt-Eriksen, Jens; Clausen, Jens

2003-01-01

We give a review of pharmaceutical R&D and mathematical simulation and optimization methods used to support decision making within the pharmaceutical development process. The complex nature of drug development is pointed out through a description of the various phases of the pharmaceutical develo...... development process. A part of the paper is dedicated to the use of simulation techniques to support clinical trials. The paper ends with a section describing portfolio modelling methods in the context of the pharmaceutical industry....

Engineering fluorescent proteins towards ultimate performances: lessons from the newly developed cyan variants

International Nuclear Information System (INIS)

Mérola, Fabienne; Erard, Marie; Fredj, Asma; Pasquier, Hélène

2016-01-01

New fluorescent proteins (FPs) are constantly discovered from natural sources, and submitted to intensive engineering based on random mutagenesis and directed evolution. However, most of these newly developed FPs fail to achieve all the performances required for their bioimaging applications. The design of highly optimised FP-based reporters, simultaneously displaying appropriate colour, multimeric state, chromophore maturation, brightness, photostability and environmental sensitivity will require a better understanding of the structural and dynamic determinants of FP photophysics. The recent development of cyan fluorescent proteins (CFPs) like mCerulean3, mTurquoise2 and Aquamarine brings a different view on these questions, as in this particular case, a step by step evaluation of critical mutations has been performed within a family of spectrally identical and evolutionary close variants. These efforts have led to CFPs with quantum yields close to unity, near single exponential emission decays, high photostability and complete insensitivity to pH, making them ideal choices as energy transfer donors in FRET and FLIM imaging applications. During this process, it was found that a proper amino-acid choice at only two positions (148 and 65) is sufficient to transform the performances of CFPs: with the help of structural and theoretical investigations, we rationalise here how these two positions critically control the CFP photophysics, in the context of FPs derived from the Aequorea victoria species. Today, these results provide a useful toolbox for upgrading the different CFP donors carried by FRET biosensors. They also trace the route towards the de novo design of FP-based optogenetic devices that will be perfectly tailored to dedicated imaging and sensing applications. (topical review)

Development of severe accident management advisory and training simulator (SAMAT)

International Nuclear Information System (INIS)

Jeong, K.-S.; Kim, K.-R.; Jung, W.-D.; Ha, J.-J.

2002-01-01

The most operator support systems including the training simulator have been developed to assist the operator and they cover from normal operation to emergency operation. For the severe accident, the overall architecture for severe accident management is being developed in some developed countries according to the development of severe accident management guidelines which are the skeleton of severe accident management architecture. In Korea, the severe accident management guideline for KSNP was recently developed and it is expected to be a central axis of logical flow for severe accident management. There are a lot of uncertainties in the severe accident phenomena and scenarios and one of the major issues for developing a operator support system for a severe accident is the reduction of these uncertainties. In this paper, the severe accident management advisory system with training simulator, SAMAT, is developed as all available information for a severe accident are re-organized and provided to the management staff in order to reduce the uncertainties. The developed system includes the graphical display for plant and equipment status, the previous research results by knowledge-base technique, and the expected plant behavior using the severe accident training simulator. The plant model used in this paper is oriented to severe accident phenomena and thus can simulate the plant behavior for a severe accident. Therefore, the developed system may make a central role of the information source for decision-making for a severe accident management, and will be used as the training simulator for severe accident management

Survey of outcomes in a faculty development program on simulation pedagogy.

Science.gov (United States)

Roh, Young Sook; Kim, Mi Kang; Tangkawanich, Thitiarpha

2016-06-01

Although many nursing programs use simulation as a teaching-learning modality, there are few systematic approaches to help nursing educators learn this pedagogy. This study evaluates the effects of a simulation pedagogy nursing faculty development program on participants' learning perceptions using a retrospective pre-course and post-course design. Sixteen Thai participants completed a two-day nursing faculty development program on simulation pedagogy. Thirteen questionnaires were used in the final analysis. The participants' self-perceived learning about simulation teaching showed significant post-course improvement. On a five-point Likert scale, the composite mean attitude, subjective norm, and perceived behavioral control scores, as well as intention to use a simulator, showed a significant post-course increase. A faculty development program on simulation pedagogy induced favorable learning and attitudes. Further studies must test how faculty performance affects the cognitive, emotional, and social dimensions of learning in a simulation-based learning domain. © 2015 Wiley Publishing Asia Pty Ltd.

Online model evaluation of large-eddy simulations covering Germany with a horizontal resolution of 156 m

Science.gov (United States)

Hansen, Akio; Ament, Felix; Lammert, Andrea

2017-04-01

Large-eddy simulations have been performed since several decades, but due to computational limits most studies were restricted to small domains or idealised initial-/boundary conditions. Within the High definition clouds and precipitation for advancing climate prediction (HD(CP)2) project realistic weather forecasting like LES simulations were performed with the newly developed ICON LES model for several days. The domain covers central Europe with a horizontal resolution down to 156 m. The setup consists of more than 3 billion grid cells, by what one 3D dump requires roughly 500 GB. A newly developed online evaluation toolbox was created to check instantaneously for realistic model simulations. The toolbox automatically combines model results with observations and generates several quicklooks for various variables. So far temperature-/humidity profiles, cloud cover, integrated water vapour, precipitation and many more are included. All kind of observations like aircraft observations, soundings or precipitation radar networks are used. For each dataset, a specific module is created, which allows for an easy handling and enhancement of the toolbox. Most of the observations are automatically downloaded from the Standardized Atmospheric Measurement Database (SAMD). The evaluation tool should support scientists at monitoring computational costly model simulations as well as to give a first overview about model's performance. The structure of the toolbox as well as the SAMD database are presented. Furthermore, the toolbox was applied on an ICON LES sensitivity study, where example results are shown.

DCS emulator development for the ACR-1000 simulator

International Nuclear Information System (INIS)

Nakashima, Y.; Trueman, R.; Ishii, K.

2010-01-01

Nuclear Power Plant (NPP) simulators are the main means for operator training and as such are a crucial part of the NPP operation life-cycle. Hitachi, Ltd., Information and Control Systems Company (henceforth 'Hitachi') is the preferred DCS and DCS emulator developer and supplier for the ACR-1000 NPP control system. Hitachi's concept for the DCS (distributed control system) portion of the ACR-1000 simulator is 'total emulation of the DCS' by software. This paper will review the current status of the technical development and the major project milestones. (author)

Development of severe accident guidance module for the SATS simulator

International Nuclear Information System (INIS)

Kim, K.R.; Park, S.H.; Kim, D.H.; Song, Y.M.

2004-01-01

Recently KAERI has developed the severe accident management guidance to establish Korea standard severe accident management system. On the other hand the PC-based severe accident training simulator SATS has been developed, which uses MELCOR code as the simulation engine. SATS graphically displays and simulates the severe accidents with interactive user commands. The control capability of SATS could make severe accident training course more interesting and effective. In this paper we will describe the development and functions of the electrical hypertext guidance module HyperKAMG and the SATS-HyperKAMG linkage system for the severe accident management. (author)

B2.5-Eunomia simulations of Pilot-PSI plasmas

International Nuclear Information System (INIS)

Wieggers, R.C.; Coster, D.P.; Groen, P.W.C.; Blank, H.J. de; Goedheer, W.J.

2013-01-01

The B2.5-Eunomia code is used to simulate the plasma and neutral species in and around a Pilot-PSI plasma beam. B2.5, part of the SOLPS5.0 code package, is a multi-fluid plasma code for the scrape-off layer. Eunomia is a newly developed non-linear Monte Carlo transport code that solves the neutral equilibrium, given a background plasma. Eunomia is developed to simulate the relevant neutral species in Pilot-PSI and Magnum-PSI, linear devices that study plasma surface interactions in conditions expected in the ITER divertor. Results show the influence of the neutral species on the Pilot-PSI plasma beam. We show that a fluid description for the neutrals is not sufficient and Eunomia is needed to describe Pilot-PSI. The treatment of individual vibrational states of molecular hydrogen as separate species is crucial to match the experiment

Non-Integrated Standalone Tests of APR1400 Simulator

International Nuclear Information System (INIS)

Hwang, Su Hyun; Lee, Jeong Ik; Hong, Soon Joon; Lee, Byung Chul; Seo, Jeong Gwan; Lee, Myung Soo

2007-01-01

APR1400 being developed for the construction of New Kori 3 and 4 Units has improved safety and more economical efficiency compared with previous PWR. The ESF(Engineered Safety Features) newly introduced to enhance safety are as follows: DVI (Direct Vessel Injection), Fluidic Device, IRWST (In-containment Refueling Water Storage Tank). So the transient pattern of anticipated accidents will show different characteristics from previous PWR. There are multidimensional flow phenomena like as emergency core cooling coolant bypass discharge in the downcomer, downcomer boiling, and different safety injection characteristics due to fluidic device during LBLOCA. Also there is the phenomenon of critical flow due to the open of pressurizer POSRV (Pilot Operated Safety Relief valve) connected to IRWST and safety depressurization system and the prediction of discharge flow is very important. KEPRI is developing APR1400 simulator using RELAP-RT . RELAP-RT was developed by DS and S (Data systems and Solutions) based on RELAP5/MOD3.2. The improved features of RELAP-RT to function as a simulator are as follows: Add simulator functionality - Control by simulator executive - IC snap and reset capability - Back-track snap and reset capability - Fast time capability. Fast time capability(examples) - The rate of condensation has been limited. - Fictional choking model has been developed for internal junctions. - Wall heat transfer coefficients and heat fluxes has been limited. In this study, various NISTs (Non-Integrated Standalone Tests) were performed to verify the capability of RELAP-RT as APR1400 simulator by the comparison with RELAP5/MOD3.3

Development of a mechanical maintenance training simulator in OpenSimulator for F-16 aircraft engines

OpenAIRE

Pinheiro, André; Fernandes, Paulo; Maia, Ana; Cruz, Gonçalo; Pedrosa, Daniela; Fonseca, Benjamim; Paredes, Hugo; Martins, Paulo; Morgado, Leonel; Rafael, Jorge

2014-01-01

Mechanical maintenance of F-16 engines is carried out as a team effort involving 3–4 skilled engine technicians, but the details of its procedures and requisites change constantly, to improve safety, optimize resources, and respond to knowledge learned from field outcomes. This provides a challenge for development of training simulators, since simulated actions risk becoming obsolete rapidly and require costly reimplementation. This paper presents the development of a 3D mechanical maintenanc...

Cold Dissolved Saltcake Waste Simulant Development, Preparation, and Analysis

International Nuclear Information System (INIS)

Rassat, Scot D.; Mahoney, Lenna A.; Russell, Renee L.; Bryan, Samuel A.; Sell, Rachel L.

2003-01-01

CH2M HILL Hanford Group, Inc. is identifying and developing supplemental process technologies to accelerate the Hanford tank waste cleanup mission. Bulk vitrification, containerized grout, and steam reforming are three technologies under consideration for treatment of the radioactive saltcake wastes in 68 single-shell tanks. To support development and testing of these technologies, Pacific Northwest National Laboratory (PNNL) was tasked with developing a cold dissolved saltcake simulant formulation to be representative of an actual saltcake waste stream, preparing 25- and 100-L batches of the simulant, and analyzing the composition of the batches to ensure conformance to formulation targets. Lacking a defined composition for dissolved actual saltcake waste, PNNL used available tank waste composition information and an equilibrium chemistry model (Environmental Simulation Program [ESP(trademark)]) to predict the concentrations of analytes in solution. Observations of insoluble solids in initial laboratory preparations for the model-predicted formulation prompted reductions in the concentration of phosphate and silicon in the final simulant formulation. The analytical results for the 25- and 100-L simulant batches, prepared by an outside vendor to PNNL specifications, agree within the expected measurement accuracy (∼10%) of the target concentrations and are highly consistent for replicate measurements, with a few minor exceptions. In parallel with the production of the 2nd simulant batch (100-L), a 1-L laboratory control sample of the same formulation was carefully prepared at PNNL to serve as an analytical standard. The instrumental analyses indicate that the vendor prepared batches of solution adequately reflect the as-formulated simulant composition. In parallel with the simulant development effort, a nominal 5-M (molar) sodium actual waste solution was prepared at the Hanford Site from a limited number of tank waste samples. Because this actual waste solution w

Development of the Transport Class Model (TCM) Aircraft Simulation From a Sub-Scale Generic Transport Model (GTM) Simulation

Science.gov (United States)

Hueschen, Richard M.

2011-01-01

A six degree-of-freedom, flat-earth dynamics, non-linear, and non-proprietary aircraft simulation was developed that is representative of a generic mid-sized twin-jet transport aircraft. The simulation was developed from a non-proprietary, publicly available, subscale twin-jet transport aircraft simulation using scaling relationships and a modified aerodynamic database. The simulation has an extended aerodynamics database with aero data outside the normal transport-operating envelope (large angle-of-attack and sideslip values). The simulation has representative transport aircraft surface actuator models with variable rate-limits and generally fixed position limits. The simulation contains a generic 40,000 lb sea level thrust engine model. The engine model is a first order dynamic model with a variable time constant that changes according to simulation conditions. The simulation provides a means for interfacing a flight control system to use the simulation sensor variables and to command the surface actuators and throttle position of the engine model.

Development of the NSSS thermal-hydraulic program for YGN unit 1 simulator

Energy Technology Data Exchange (ETDEWEB)

Kim, Kyung Doo; Jeong, Jae Jun; Lee, Won Jae; Chung, Bub Dong; Ha, Kwi Seok; Kang, Kyung Ho

2000-09-01

The NSSS thermal-hydraulic programs installed in the domestic full-scope power plant simulators were provided in early 1980s by foreign vendors. Because of limited computational capability at that time, they usually adopt very simplified physical models for a real-time simulation of NSSS thermal-hydraulic phenomena, which entails inaccurate results and the possibility of so-called 'negative training', especially for complicated two-phase flows in the reactor coolant system. To resolve the problem, we developed a realistic NSSS T/H program (named 'ARTS' code) for use in YongGwang Nuclear Unit 1 full-scope simulator. The best-estimate code RETRAN03, developed by EPRI and approved by USNRC, was selected as a reference code of ARTS. For the development of ARTS, the followings have been performed: -Improvement of the robustness of RETRAN - Improvement of the real-time simulation capability of RETRAN - Optimum input data generation for the NSSS simulation - New model development that cannot be efficiently modeled by RETRAN - Assessment of the ARTS code. The systematic assessment of ARTS has been conducted in both personal computers (Windows 98, Visual fortran) and the simulator development environment (Windows NT, GSE simulator development tool). The results were resonable in terms of accuracy, real-time simulation and robustness.

Development of the NSSS thermal-hydraulic program for YGN unit 1 simulator

International Nuclear Information System (INIS)

Kim, Kyung Doo; Jeong, Jae Jun; Lee, Won Jae; Chung, Bub Dong; Ha, Kwi Seok; Kang, Kyung Ho

2000-09-01

The NSSS thermal-hydraulic programs installed in the domestic full-scope power plant simulators were provided in early 1980s by foreign vendors. Because of limited computational capability at that time, they usually adopt very simplified physical models for a real-time simulation of NSSS thermal-hydraulic phenomena, which entails inaccurate results and the possibility of so-called 'negative training', especially for complicated two-phase flows in the reactor coolant system. To resolve the problem, we developed a realistic NSSS T/H program (named 'ARTS' code) for use in YongGwang Nuclear Unit 1 full-scope simulator. The best-estimate code RETRAN03, developed by EPRI and approved by USNRC, was selected as a reference code of ARTS. For the development of ARTS, the followings have been performed: -Improvement of the robustness of RETRAN - Improvement of the real-time simulation capability of RETRAN - Optimum input data generation for the NSSS simulation - New model development that cannot be efficiently modeled by RETRAN - Assessment of the ARTS code. The systematic assessment of ARTS has been conducted in both personal computers (Windows 98, Visual fortran) and the simulator development environment (Windows NT, GSE simulator development tool). The results were resonable in terms of accuracy, real-time simulation and robustness

Status of photovoltaics in the Newly Associated States

International Nuclear Information System (INIS)

Pietruszko, S.M.; Mikolajuk, A.; Fara, L.; Fara, S.; Vitanov, P.; Stratieva, N.; Rehak, J.; Barinka, R.; Mellikov, E.; Palfy, M.; Shipkovs, P.; Krotkus, A.; Saly, V.; Nemac, F.; Swens, J.; Nowak, S.; Zachariou, A.; Fechner, H.; Passiniemi, P.

2004-01-01

The Status of Photovoltaics in the Central and Eastern Europe presents the state of the art of photovoltaics (PV) in the Newly Associated States (NAS): Bulgaria, the Czech Republic, Estonia, Hungary, Latvia, Lithuania, Poland, Romania, Slovakia, Slovenia. The attempt was made to cover all photovoltaics activities in NAS, from research to industry and markets as well as from technology development to dissemination and education. The document covers the following topics and issues: organization of PV research and demonstration activities, stakeholders involved in research and technology development (RTD), scientific potential of NAS PV community, PV activities carried out in NAS countries, PV policies and support mechanisms, achievements and barriers, challenges and needs to the development of PV in the NAS. (authors)

Needs analysis for developing a virtual-reality NOTES simulator.

Science.gov (United States)

Sankaranarayanan, Ganesh; Matthes, Kai; Nemani, Arun; Ahn, Woojin; Kato, Masayuki; Jones, Daniel B; Schwaitzberg, Steven; De, Suvranu

2013-05-01

INTRODUCTION AND STUDY AIM: Natural orifice translumenal endoscopic surgery (NOTES) is an emerging surgical technique that requires a cautious adoption approach to ensure patient safety. High-fidelity virtual-reality-based simulators allow development of new surgical procedures and tools and train medical personnel without risk to human patients. As part of a project funded by the National Institutes of Health, we are developing the virtual transluminal endoscopic surgery trainer (VTEST) for this purpose. The objective of this study is to conduct a structured needs analysis to identify the design parameters for such a virtual-reality-based simulator for NOTES. A 30-point questionnaire was distributed at the 2011 National Orifice Surgery Consortium for Assessment and Research meeting to obtain responses from experts. Ordinal logistic regression and the Wilcoxon rank-sum test were used for analysis. A total of 22 NOTES experts participated in the study. Cholecystectomy (CE, 68 %) followed by appendectomy (AE, 63 %) (CE vs AE, p = 0.0521) was selected as the first choice for simulation. Flexible (FL, 47 %) and hybrid (HY, 47 %) approaches were equally favorable compared with rigid (RI, 6 %) with p virtual NOTES simulator in training and testing new tools for NOTES were rated very high by the participants. Our study reinforces the importance of developing a virtual NOTES simulator and clearly presents expert preferences. The results of this analysis will direct our initial development of the VTEST platform.

Simulation of Material Flow Through a Sample Divider

Directory of Open Access Journals (Sweden)

Jiří Rozbroj

2018-03-01

Full Text Available The prerequisite for a modern approach to innovative procedures of the development of current or even newly created equipment for the transport of particulate materials is the utilization of simulation methods, such as the Discrete Element Method (DEM. This article focuses on the basic, or initial, validation of movement of material through the sample divider. The mechanical-physical properties of brown coal were measured. Based on these parameters the preliminary input values for EDEM Academic were selected, and a simulation of the dividing process was run. The key monitored parameters included density and friction coefficient. Experiments on a realistic model of the equipment were performed and assessed. The total weights of brown coal at the exit from the divider were determined for a specific speed of the divider. The aim of this task was to simulate the realistically determined weight division of the brown coal sample. The result from the DEM was compared with the results of measurement on a realistic model.

Engineering-Based Thermal CFD Simulations on Massive Parallel Systems

KAUST Repository

Frisch, Jérôme

2015-05-22

The development of parallel Computational Fluid Dynamics (CFD) codes is a challenging task that entails efficient parallelization concepts and strategies in order to achieve good scalability values when running those codes on modern supercomputers with several thousands to millions of cores. In this paper, we present a hierarchical data structure for massive parallel computations that supports the coupling of a Navier–Stokes-based fluid flow code with the Boussinesq approximation in order to address complex thermal scenarios for energy-related assessments. The newly designed data structure is specifically designed with the idea of interactive data exploration and visualization during runtime of the simulation code; a major shortcoming of traditional high-performance computing (HPC) simulation codes. We further show and discuss speed-up values obtained on one of Germany’s top-ranked supercomputers with up to 140,000 processes and present simulation results for different engineering-based thermal problems.

Preparedness of newly qualified midwives to deliver clinical care: an evaluation of pre-registration midwifery education through an analysis of key events.

Science.gov (United States)

Skirton, Heather; Stephen, Nicole; Doris, Faye; Cooper, Maggie; Avis, Mark; Fraser, Diane M

2012-10-01

this study was part of a larger project commissioned to ascertain whether midwife teachers bring a unique contribution to the preparation of midwives for practice. The aim of this phase was to determine whether the student midwives' educational programme had equipped them to practise competently after entry to the professional register. this was a prospective, longitudinal qualitative study, using participant diaries to collect data. data were collected from newly qualified midwives during the initial six months after they commenced their first post as a qualified midwife. the potential participants were all student midwives who were completing their education at one of six Universities (three in England, one in Scotland, one in Wales and one in Northern Ireland). Diary data were submitted by 35 newly qualified midwives; 28 were graduates of the three year programme and seven of the shortened programme. diary entries were analysed using thematic analysis (Braun and Clarke, 2006), with a focus on identification of key events in the working lives of the newly qualified midwives. A total of 263 key events were identified, under three main themes: (1) impact of the event on confidence, (2) gaps in knowledge or experience and (3) articulated frustration, conflict or distress. essentially, pre-registration education, delivered largely by midwife teachers and supported by clinical mentors, has been shown to equip newly qualified midwives to work effectively as autonomous practitioners caring for mothers and babies. While newly qualified midwives are able to cope with a range of challenging clinical situations in a safe manner, they lack confidence in key areas. Positive reinforcement by supportive colleagues plays a significant role in enabling them to develop as practitioners. whilst acknowledging the importance of normality in childbearing there is a need within the curriculum to enable midwives to recognise and respond to complex care situations by providing theory

The Activity of Carbohydrate-Degrading Enzymes in the Development of Brood and Newly Emerged workers and Drones of the Carniolan Honeybee, Apis mellifera carnica

OpenAIRE

Żółtowska, Krystyna; Lipiński, Zbigniew; Łopieńska-Biernat, Elżbieta; Farjan, Marek; Dmitryjuk, Małgorzata

2012-01-01

The activity of glycogen Phosphorylase and carbohydrate hydrolyzing enzymes α-amylase, glucoamylase, trehalase, and sucrase was studied in the development of the Carniolan honey bee, Apis mellifera carnica Pollman (Hymenoptera: Apidae), from newly hatched larva to freshly emerged imago of worker and drone. Phosphorolytic degradation of glycogen was significantly stronger than hydrolytic degradation in all developmental stages. Developmental profiles of hydrolase activity were similar in both ...

Computer simulation studies in condensed-matter physics 5. Proceedings

International Nuclear Information System (INIS)

Landau, D.P.; Mon, K.K.; Schuettler, H.B.

1993-01-01

As the role of computer simulations began to increase in importance, we sensed a need for a ''meeting place'' for both experienced simulators and neophytes to discuss new techniques and results in an environment which promotes extended discussion. As a consequence of these concerns, The Center for Simulational Physics established an annual workshop on Recent Developments in Computer Simulation Studies in Condensed-Matter Physics. This year's workshop was the fifth in this series and the interest which the scientific community has shown demonstrates quite clearly the useful purpose which the series has served. The workshop was held at the University of Georgia, February 17-21, 1992, and these proceedings from a record of the workshop which is published with the goal of timely dissemination of the papers to a wider audience. The proceedings are divided into four parts. The first part contains invited papers which deal with simulational studies of classical systems and includes an introduction to some new simulation techniques and special purpose computers as well. A separate section of the proceedings is devoted to invited papers on quantum systems including new results for strongly correlated electron and quantum spin models. The third section is comprised of a single, invited description of a newly developed software shell designed for running parallel programs. The contributed presentations comprise the final chapter. (orig.). 79 figs

Temporal bone dissection simulator for training pediatric otolaryngology surgeons

Science.gov (United States)

Tabrizi, Pooneh R.; Sang, Hongqiang; Talari, Hadi F.; Preciado, Diego; Monfaredi, Reza; Reilly, Brian; Arikatla, Sreekanth; Enquobahrie, Andinet; Cleary, Kevin

2017-03-01

Cochlear implantation is the standard of care for infants born with severe hearing loss. Current guidelines approve the surgical placement of implants as early as 12 months of age. Implantation at a younger age poses a greater surgical challenge since the underdeveloped mastoid tip, along with thin calvarial bone, creates less room for surgical navigation and can result in increased surgical risk. We have been developing a temporal bone dissection simulator based on actual clinical cases for training otolaryngology fellows in this delicate procedure. The simulator system is based on pre-procedure CT (Computed Tomography) images from pediatric infant cases (hospital. The simulator includes: (1) simulation engine to provide the virtual reality of the temporal bone surgery environment, (2) a newly developed haptic interface for holding the surgical drill, (3) an Oculus Rift to provide a microscopic-like view of the temporal bone surgery, and (4) user interface to interact with the simulator through the Oculus Rift and the haptic device. To evaluate the system, we have collected 10 representative CT data sets and segmented the key structures: cochlea, round window, facial nerve, and ossicles. The simulator will present these key structures to the user and warn the user if needed by continuously calculating the distances between the tip of surgical drill and the key structures.

Three-dimensional quantification of cardiac surface motion: a newly developed three-dimensional digital motion-capture and reconstruction system for beating heart surgery.

Science.gov (United States)

Watanabe, Toshiki; Omata, Sadao; Odamura, Motoki; Okada, Masahumi; Nakamura, Yoshihiko; Yokoyama, Hitoshi

2006-11-01

This study aimed to evaluate our newly developed 3-dimensional digital motion-capture and reconstruction system in an animal experiment setting and to characterize quantitatively the three regional cardiac surface motions, in the left anterior descending artery, right coronary artery, and left circumflex artery, before and after stabilization using a stabilizer. Six pigs underwent a full sternotomy. Three tiny metallic markers (diameter 2 mm) coated with a reflective material were attached on three regional cardiac surfaces (left anterior descending, right coronary, and left circumflex coronary artery regions). These markers were captured by two high-speed digital video cameras (955 frames per second) as 2-dimensional coordinates and reconstructed to 3-dimensional data points (about 480 xyz-position data per second) by a newly developed computer program. The remaining motion after stabilization ranged from 0.4 to 1.01 mm at the left anterior descending, 0.91 to 1.52 mm at the right coronary artery, and 0.53 to 1.14 mm at the left circumflex regions. Significant differences before and after stabilization were evaluated in maximum moving velocity (left anterior descending 456.7 +/- 178.7 vs 306.5 +/- 207.4 mm/s; right coronary artery 574.9 +/- 161.7 vs 446.9 +/- 170.7 mm/s; left circumflex 578.7 +/- 226.7 vs 398.9 +/- 192.6 mm/s; P heart surface movement. This helps us better understand the complexity of the heart, its motion, and the need for developing a better stabilizer for beating heart surgery.

Simulation modelling: educational development roles for learning technologists

Directory of Open Access Journals (Sweden)

David Riley

2002-12-01

Full Text Available Simulation modelling was in the mainstream of CAL development in the 1980s when the late David Squires introduced this author to the Dynamic Modelling System. Since those early days, it seems that simulation modelling has drifted into a learning technology backwater to become a member of Laurillard's underutilized, 'adaptive and productive' media. Referring to her Conversational Framework, Laurillard constructs a pedagogic case for modelling as a productive student activity but provides few references to current practice and available resources. This paper seeks to complement her account by highlighting the pioneering initiatives of the Computers in the Curriculum Project and more recent developments in systems modelling within geographic and business education. The latter include improvements to system dynamics modelling programs such as STELLA®, the publication of introductory textbooks, and the emergence of online resources. The paper indicates several ways in which modelling activities may be approached and identifies some educational development roles for learning technologists. The paper concludes by advocating simulation modelling as an exemplary use of learning technologies - one that realizes their creative-transformative potential.

Key issues and challenges in developing a pedagogical intervention in the simulation skills center--an action research study.

Science.gov (United States)

Reierson, Inger Åse; Hvidsten, Anne; Wighus, Marianne; Brungot, Solvor; Bjørk, Ida Torunn

2013-07-01

Simulation skills centers (SSC) are considered important learning arenas for preparing and qualifying nursing students. Limited clinical placements and claims of diminished learning opportunities raise concerns that newly educated nurses lack proficiency in many psychomotor skills. Accordingly, there is an increased focus on learning in the SSC. However, it has been questioned if the pedagogical underpinning of teaching and learning in the SSC is missing or unclear. At a bachelor nursing education in Norway, there was a desire to change practice and enhance learning in the SSC by systematic use of The Model of Practical Skill Performance (Bjørk and Kirkevold, 2000). A participatory action research design was chosen. A pedagogical intervention was developed and implemented in 2010 in a cohort of eighty-seven first year bachelor nursing students during their basic nursing skill course. The intervention is shortly described. This article reports key issues and challenges that emerged during development of the new intervention. Data to inform the study were collected via thorough meeting minutes and the project leader's logbook, and analyzed using fieldnotes analysis. Six key issues and challenges were identified. These are presented and discussed consecutively in light of their importance for development and implementation of the new intervention. Copyright © 2013 Elsevier Ltd. All rights reserved.

Random number generators for large-scale parallel Monte Carlo simulations on FPGA

Science.gov (United States)

Lin, Y.; Wang, F.; Liu, B.

2018-05-01

Through parallelization, field programmable gate array (FPGA) can achieve unprecedented speeds in large-scale parallel Monte Carlo (LPMC) simulations. FPGA presents both new constraints and new opportunities for the implementations of random number generators (RNGs), which are key elements of any Monte Carlo (MC) simulation system. Using empirical and application based tests, this study evaluates all of the four RNGs used in previous FPGA based MC studies and newly proposed FPGA implementations for two well-known high-quality RNGs that are suitable for LPMC studies on FPGA. One of the newly proposed FPGA implementations: a parallel version of additive lagged Fibonacci generator (Parallel ALFG) is found to be the best among the evaluated RNGs in fulfilling the needs of LPMC simulations on FPGA.

A model for mentoring newly-appointed nurse educators in nursing education institutions in South Africa.

Science.gov (United States)

Seekoe, Eunice

2014-04-24

South Africa transformed higher education through the enactment of the Higher Education Act (No. 101 of 1997). The researcher identified the need to develop a model for the mentoring of newly-appointed nurse educators in nursing education institutions in South Africa.  To develop and describe the model for mentoring newly-appointed nurse educators in nursing education institutions in South Africa.  A qualitative and theory-generating design was used (following empirical findings regarding needs analysis) in order to develop the model. The conceptualisation of the framework focused on the context, content, process and the theoretical domains that influenced the model. Ideas from different theories were borrowed from and integrated with the literature and deductive and inductive strategies were applied.  The structure of the model is multidimensional and complex in nature (macro, mesoand micro) based on the philosophy of reflective practice, competency-based practice andcritical learning theories. The assumptions are in relation to stakeholders, context, mentoring, outcome, process and dynamic. The stakeholders are the mentor and mentee within an interactive participatory relationship. The mentoring takes place within the process with a sequence of activities such as relationship building, development, engagement, reflective process and assessment. Capacity building and empowerment are outcomes of mentoring driven by motivation.  The implication for nurse managers is that the model can be used to develop mentoring programmes for newly-appointed nurse educators.

Development status of the integrated tokamak simulator for K-DEMO

Energy Technology Data Exchange (ETDEWEB)

Kang, J. S.; Wang, J.; Hwang, Y. S. [Seoul National University, Seoul (Korea, Republic of); Jung, L. [National Fusion Research Institute, Daejeon (Korea, Republic of)

2016-10-15

Korean fusion demonstration reactor (K-DEMO) study has been conducted to investigate the feasibility of an electricity generation, self-sustained tritium cycle, and component test facility. To estimate its capability, the integrated fusion operation simulator called INFRA has been developed by organizing relevant computational codes with standard data models and framework. The different modules of the integrated simulator are chosen among well-validated codes. Standard data models are directly linked with KSTAR experimental data so that the integrated simulator can be used for interpretative simulations but also for predictive simulations. In this study, the current status of code development and some examples of KSTAR interpretative simulations are reported. ITER integrated modelling and analysis suite is imported to K-DEMO data model to take over ITER experience and to accelerate collaboration with international IMAS community. Standardized rules and guideline have been developed by ITER team for many years. Based on strict policy, this data model has been established and updated. This data model is used for experimental and simulation results. The INFRA system has been utilized to be an alpha version of a KDEMO simulator. Database, framework, and module integration are conducted. A test equilibrium run for KSTAR is done by filling the database with experiment results. More modules will be incorporated in a near future. Validation with KSTAR data and benchmarking previous modelling activity is also planned in order to confirm the feasibility of this system.

Development of a flight simulator for the control of plasma discharges

International Nuclear Information System (INIS)

Ravenel, N.; Artaud, J.F.; Bremond, S.; Guillerminet, B.; Huynh, P.; Moreau, P.; Signoret, J.

2010-01-01

The feedback control of fusion experiments in tokamak devices is entering a new area driven by the increase of control requirements for obtaining burning plasmas under safe operation conditions. A project aiming at setting up a flight simulator for the development of advanced controllers has started last year at CEA. This simulator will reuse most of the components of the European Integrated Tokamak Modelling (ITM) simulation platform. Thus, it will benefit from the development made by the task force and it will be able to offer a development platform for the new controllers of present day European tokamaks and future machines. This paper provides an overview of the architecture of the simulator. The functional specifications of the simulator have been defined and the needs in interface implementation are analysed as well.

Development of in-situ visualization tool for PIC simulation

International Nuclear Information System (INIS)

Ohno, Nobuaki; Ohtani, Hiroaki

2014-01-01

As the capability of a supercomputer is improved, the sizes of simulation and its output data also become larger and larger. Visualization is usually carried out on a researcher's PC with interactive visualization software after performing the computer simulation. However, the data size is becoming too large to do it currently. A promising answer is in-situ visualization. For this case a simulation code is coupled with the visualization code and visualization is performed with the simulation on the same supercomputer. We developed an in-situ visualization tool for particle-in-cell (PIC) simulation and it is provided as a Fortran's module. We coupled it with a PIC simulation code and tested the coupled code on Plasma Simulator supercomputer, and ensured that it works. (author)

Development of simulation technology on full auto air conditioning system; Auto eakon no simulation gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Fujita, N; Otsubo, Y; Matsumura, K; Sako, H [Mazda Motor Corp., Hiroshima (Japan)

1997-10-01

Mazda has developed simulation technology on control of full auto air conditioning system. We have developed the development tool based on the technology, aiming at higher controllability of full auto air conditioning system and shorter development period. The tool performs simulation on control, on-vehicle evaluation of actual load operation, collecting data and analyzing them by personal computer. This paper reports our verification results on effectiveness of the technology/ and the tool. 4 refs., 9 figs.

RELATIONSHIP BETWEEN DIFFERENT ALLOGAMIC ASSOCIATED TRAIT CHARACTERISTICS OF THE FIVE NEWLY DEVELOPED CYTOPLASMIC MALE STERILE (CMS LINES IN RICE

Directory of Open Access Journals (Sweden)

Nematzadeh GHORBAN ALI

2006-10-01

Full Text Available Five suitable maintainer varieties were identifi ed through testcrosses with IR58025A and the transfer of wild abortive cytoplasm was carried out by seven successive backcrosses. Five new CMS lines were developed by this approach in well adapted high yielding improved varietal background such as ‘Nemat’, ‘Neda’, ‘Dasht’, ‘Amol3’ and ‘Champa’. Agronomical characterization and allogamy-associated traits of the fi ve newly developed CMS lines were studied for their interrelationship. Anther length had a signifi cant positive correlation with the duration of glume opening (0.759 and high correlation of (0.698 with the angle between lemma and palea. The results indicated that ‘Nemat’ A, ‘Neda’ A, ‘Dasht’ A are more suitable as parents for hybrid seed production due to their favorable and superior fl oral characteristics in comparison to IR58025A.

Development of a Free-Flight Simulation Infrastructure

Science.gov (United States)

Miles, Eric S.; Wing, David J.; Davis, Paul C.

1999-01-01

In anticipation of a projected rise in demand for air transportation, NASA and the FAA are researching new air-traffic-management (ATM) concepts that fall under the paradigm known broadly as ":free flight". This paper documents the software development and engineering efforts in progress by Seagull Technology, to develop a free-flight simulation (FFSIM) that is intended to help NASA researchers test mature-state concepts for free flight, otherwise referred to in this paper as distributed air / ground traffic management (DAG TM). Under development is a distributed, human-in-the-loop simulation tool that is comprehensive in its consideration of current and envisioned communication, navigation and surveillance (CNS) components, and will allow evaluation of critical air and ground traffic management technologies from an overall systems perspective. The FFSIM infrastructure is designed to incorporate all three major components of the ATM triad: aircraft flight decks, air traffic control (ATC), and (eventually) airline operational control (AOC) centers.

Simulations of Precipitate Microstructure Evolution during Heat Treatment

Science.gov (United States)

Wu, Kaisheng; Sterner, Gustaf; Chen, Qing; Jou, Herng-Jeng; Jeppsson, Johan; Bratberg, Johan; Engström, Anders; Mason, Paul

Precipitation, a major solid state phase transformation during heat treatment processes, has for more than one century been intensively employed to improve the strength and toughness of various high performance alloys. Recently, sophisticated precipitation reaction models, in assistance with well-developed CALPHAD databases, provide an efficient and cost-effective way to tailor precipitate microstructures that maximize the strengthening effect via the optimization of alloy chemistries and heat treatment schedules. In this presentation, we focus on simulating precipitate microstructure evolution in Nickel-base superalloys under arbitrary heat treatment conditions. The newly-developed TC-PRISMA program has been used for these simulations, with models refined especially for non-isothermal conditions. The effect of different cooling profiles on the formation of multimodal microstructures has been thoroughly examined in order to understand the underlying thermodynamics and kinetics. Meanwhile, validations against several experimental results have been carried out. Practical issues that are critical to the accuracy and applicability of the current simulations, such as modifications that overcome mean-field approximations, compatibility between CALPHAD databases, selection of key parameters (particularly interfacial energy and nucleation site densities), etc., are also addressed.

Simulation of an Aspheric Glass Lens Forming Behavior in Progressive GMP Process

International Nuclear Information System (INIS)

Chang, Sung Ho; Lee, Young Min; Kang, Jeong Jin; Hong, Seok Kwan; Shin, Gwang Ho; Heo, Young Moo; Jung, Tae Sung

2007-01-01

Recently, GMP(Glass Molding Press) process is mainly used to produce aspheric glass lenses. Because glass lens is heated at high temperature above Tg (Transformation Temperature) for forming the glass, the quality of aspheric glass lens is deteriorated by residual stresses which are generated in a aspheric glass lens after forming. In this study, as a fundamental study to develop the mold for progressive GMP process, we conducted a aspheric glass lens forming simulation. Prior to a aspheric glass lens forming simulation, compression and thermal conductivity tests were carried out to obtain mechanical and thermal properties of K-PBK40 which is newly developed material for precision molding, and flow characteristics of K-PBK40 were obtained at high temperature. Then, using the flow characteristics obtained, compression simulation was carried out and compared with the experimental result for the purpose of verifying the obtained flow characteristics. Finally, a glass lens press simulation in progressive GMP process was carried out and we could forecast the shape of deformed glass lenses and residual stresses contribution in the structure of deformed glass lenses after forming

Development of a prototype graphic simulation program for severe accident training

International Nuclear Information System (INIS)

Kim, Ko Ryu; Jeong, Kwang Sub; Ha, Jae Joo

2000-05-01

This is a report of the development process and related technologies of severe accident graphic simulators, required in industrial severe accident management and training. Here, we say 'a severe accident graphic simulator' as a graphics add-in system to existing calculation codes, which can show the severe accident phenomena dynamically on computer screens and therefore which can supplement one of main defects of existing calculation codes. With graphic simulators it is fairly easy to see the total behavior of nuclear power plants, where it was very difficult to see only from partial variable numerical information. Moreover, the fast processing and control feature of a graphic simulator can give some opportunities of predicting the severe accident advancement among several possibilities, to one who is not an expert. Utilizing graphic simulators' we expect operators' and TSC members' physical phenomena understanding enhancement from the realistic dynamic behavior of plants. We also expect that severe accident training course can gain better training effects using graphic simulator's control functions and predicting capabilities, and therefore we expect that graphic simulators will be effective decision-aids tools both in sever accident training course and in real severe accident situations. With these in mind, we have developed a prototype graphic simulator having surveyed related technologies, and from this development experiences we have inspected the possibility to build a severe accident graphic simulator. The prototype graphic simulator is developed under IBM PC WinNT environments and is suited to Uljin 3and4 nuclear power plant. When supplied with adequate severe accident scenario as an input, the prototype can provide graphical simulations of plant safety systems' dynamic behaviors. The prototype is composed of several different modules, which are phenomena display module, MELCOR data interface module and graphic database interface module. Main functions of

The SimPort-based simulators and distributed control systems development, upgrade and testing

International Nuclear Information System (INIS)

Danilov, Victor A.; Yanushevich, Dmitry I.; Zenkov, Andrey D.

2004-01-01

This paper describes the SimPort computer technology application experience related with power plant simulators and Distributed Control System (DCS) emulators development. The paper presents basic characteristics of the SimPort as a Windows NT-based implementation variety of the developed in RRC 'Kurchatov Institute' math modeling and simulator creation AIS technology. The new approaches and benefits of using simulation for DCS development and, especially upgrade, testing and on plant tuning are presented in the paper briefly. The DCS-inclusive power plant SimPort-based simulators are also considered. The DCS emulation principal problems, solutions and the experience-based DCS emulators development methodology are presented also. The presented technology quality and efficiency as well as presented DCS emulation problem solutions were verified by the smallest power plant full scope computer simulators development man-hours (at least twice lower in comparison with the similar simulators) in combination with the simulators correspondence to the standard and the best quality of nuclear power plant simulators. (Author)

PyECLOUD and build-up simulations at CERN

International Nuclear Information System (INIS)

Iadarola, G; Rumolo, G

2013-01-01

PyECLOUD is a newly developed code for the simulation of the electron cloud (EC) build-up in particle accelerators. Almost entirely written in Python, it is mostly based on the physical models already used in the ECLOUD code but, thanks to the implementation of new optimized algorithms, it exhibits a significantly improved performance in accuracy, speed, reliability and flexibility. Such new features of PyECLOUD have been already broadly exploited to study EC observations in the Large Hadron Collider (LHC) and its injector chain as well as for the extrapolation to high luminosity upgrade scenarios. (author)

Clinical Prediction Model for Time in Therapeutic Range While on Warfarin in Newly Diagnosed Atrial Fibrillation.

Science.gov (United States)

Williams, Brent A; Evans, Michael A; Honushefsky, Ashley M; Berger, Peter B

2017-10-12

Though warfarin has historically been the primary oral anticoagulant for stroke prevention in newly diagnosed atrial fibrillation (AF), several new direct oral anticoagulants may be preferred when anticoagulation control with warfarin is expected to be poor. This study developed a prediction model for time in therapeutic range (TTR) among newly diagnosed AF patients on newly initiated warfarin as a tool to assist decision making between warfarin and direct oral anticoagulants. This electronic medical record-based, retrospective study included newly diagnosed, nonvalvular AF patients with no recent warfarin exposure receiving primary care services through a large healthcare system in rural Pennsylvania. TTR was estimated as the percentage of time international normalized ratio measurements were between 2.0 and 3.0 during the first year following warfarin initiation. Candidate predictors of TTR were chosen from data elements collected during usual clinical care. A TTR prediction model was developed and temporally validated and its predictive performance was compared with the SAMe-TT 2 R 2 score (sex, age, medical history, treatment, tobacco, race) using R 2 and c-statistics. A total of 7877 newly diagnosed AF patients met study inclusion criteria. Median (interquartile range) TTR within the first year of starting warfarin was 51% (32, 67). Of 85 candidate predictors evaluated, 15 were included in the final validated model with an R 2 of 15.4%. The proposed model showed better predictive performance than the SAMe-TT 2 R 2 score ( R 2 =3.0%). The proposed prediction model may assist decision making on the proper mode of oral anticoagulant among newly diagnosed AF patients. However, predicting TTR on warfarin remains challenging. © 2017 The Authors. Published on behalf of the American Heart Association, Inc., by Wiley.

Adoption of Test Driven Development and Continuous Integration for the Development of the Trick Simulation Toolkit

Science.gov (United States)

Penn, John M.

2013-01-01

This paper describes the adoption of a Test Driven Development approach and a Continuous Integration System in the development of the Trick Simulation Toolkit, a generic simulation development environment for creating high fidelity training and engineering simulations at the NASA/Johnson Space Center and many other NASA facilities. It describes what was learned and the significant benefits seen, such as fast, thorough, and clear test feedback every time code is checked-in to the code repository. It also describes a system that encourages development of code that is much more flexible, maintainable, and reliable. The Trick Simulation Toolkit development environment provides a common architecture for user-defined simulations. Trick builds executable simulations using user-supplied simulation-definition files (S_define) and user supplied "model code". For each Trick-based simulation, Trick automatically provides job scheduling, checkpoint / restore, data-recording, interactive variable manipulation (variable server), and an input-processor. Also included are tools for plotting recorded data and various other supporting tools and libraries. Trick is written in C/C++ and Java and supports both Linux and MacOSX. Prior to adopting this new development approach, Trick testing consisted primarily of running a few large simulations, with the hope that their complexity and scale would exercise most of Trick's code and expose any recently introduced bugs. Unsurprising, this approach yielded inconsistent results. It was obvious that a more systematic, thorough approach was required. After seeing examples of some Java-based projects that used the JUnit test framework, similar test frameworks for C and C++ were sought. Several were found, all clearly inspired by JUnit. Googletest, a freely available Open source testing framework, was selected as the most appropriate and capable. The new approach was implemented while rewriting the Trick memory management component, to eliminate a

The activity of carbohydrate-degrading enzymes in the development of brood and newly emerged workers and drones of the Carniolan honeybee, Apis mellifera carnica.

Science.gov (United States)

Żółtowska, Krystyna; Lipiński, Zbigniew; Łopieńska-Biernat, Elżbieta; Farjan, Marek; Dmitryjuk, Małgorzata

2012-01-01

The activity of glycogen Phosphorylase and carbohydrate hydrolyzing enzymes α-amylase, glucoamylase, trehalase, and sucrase was studied in the development of the Carniolan honey bee, Apis mellifera carnica Pollman (Hymenoptera: Apidae), from newly hatched larva to freshly emerged imago of worker and drone. Phosphorolytic degradation of glycogen was significantly stronger than hydrolytic degradation in all developmental stages. Developmental profiles of hydrolase activity were similar in both sexes of brood; high activity was found in unsealed larvae, the lowest in prepupae followed by an increase in enzymatic activity. Especially intensive increases in activity occurred in the last stage of pupae and newly emerged imago. Besides α-amylase, the activities of other enzymes were higher in drone than in worker broods. Among drones, activity of glucoamylase was particularly high, ranging from around three times higher in the youngest larvae to 13 times higher in the oldest pupae. This confirms earlier suggestions about higher rates of metabolism in drone broods than in worker broods.

Confidence in leadership among the newly qualified.

Science.gov (United States)

Bayliss-Pratt, Lisa; Morley, Mary; Bagley, Liz; Alderson, Steven

2013-10-23

The Francis report highlighted the importance of strong leadership from health professionals but it is unclear how prepared those who are newly qualified feel to take on a leadership role. We aimed to assess the confidence of newly qualified health professionals working in the West Midlands in the different competencies of the NHS Leadership Framework. Most respondents felt confident in their abilities to demonstrate personal qualities and work with others, but less so at managing or improving services or setting direction.

The development of graphic simulation technology for tele-operated robot

International Nuclear Information System (INIS)

Kim, Chang Hoi; Kim, Seung Ho; Kim, Ki Ho; Jung, Seung Ho; Hwang, Suk Yeoung; Kim, Byung Soo; Seo, Yong Chil; Lee, Young Kwang

1998-02-01

In hostile environments like a nuclear power plant, human access is limited to the strict minimum due to the high-level of radiation. The design of tele-robotic system requires careful preparation because of the nature of its safety. Also, the human operator should have a capability of supervising the robot system and responding promptly to the unexpected events. In this study, the graphic simulation technology has been developed to construct tele-robotic system which can effectively perform the specified tasks in nuclear facilities. The developed graphic simulator utilizes the Indigo 2 workstation of Silicon Graphics as a main computer and its software is written in the OpenGL graphic library in X windows environments. The developed simulator, interfaced with the control system of the real robot through the ethernet, acts as a supervisory controller. Since clear and concise visual information on real robot posture and task environments can be processed in real time, the efficiency of tele-operation can be remarkably enhanced with this simulator. This simulator using advanced 3 dimensional graphics has many advantages of modeling complicated shapes of robot and constructing the virtual work environments similar to the real ones. With the use of this developed simulator, the operator can evaluate the performance of the tele-robot before it is put into real operation. This system can prevents the possible disaster of the robot resulting from the collision with its work environments. (author). 9 refs., 23 tabs., 13 figs

Games and Simulations in Online Learning: Research and Development Frameworks

Science.gov (United States)

Gibson, David; Aldrich, Clark; Prensky, Marc

2007-01-01

Games and Simulations in Online Learning: Research and Development Frameworks examines the potential of games and simulations in online learning, and how the future could look as developers learn to use the emerging capabilities of the Semantic Web. It presents a general understanding of how the Semantic Web will impact education and how games and…

Direct measurement of newly synthesized ATP dissociation kinetics in sarcoplasmic reticulum ATPase

International Nuclear Information System (INIS)

Teruel-Puche, J.; Kurzmack, M.; Inesi, G.

1987-01-01

Incubation of SR vesicles with Ca 2+ and ( 32 P)acetylphosphate, yields steady state levels of ( 32 P)phosphorylated enzyme (ATPase) intermediate and high concentrations of Ca 2+ in the lumen of the vesicles. At this time, addition of ADP (and EGTA to lower the Ca 2+ concentration in the medium outside the vesicles) results in single cycle formation of (γ- 32 P)ATP by transfer of ( 32 P)phosphate from the enzyme intermediate to ADP. The phosphoenzyme decay and ATP formation exhibit a fast component within the first 20 msec following addition of ADP, and a slower component reaching an asymptote in approximately 100 msec. They have now measured by a rapid filtration method the fraction of newly synthesized ATP which is bound to the enzyme, as opposed to the fraction dissociated into the medium. They find that nearly all the ATP formed during the initial burst is still bound to the enzyme within the initial 20 msec of reaction. Dissociation of newly synthesized ATP occurs then with approximately 13 sec -1 rate constant, permitting reequilibration of the system and further formation of ATP. The rate limiting effect of ATP dissociation and other partial reactions on the slow component of single cycle ATP synthesis is evaluated by appropriate kinetic simulations

Development of a CT simulator and its current clinical status

International Nuclear Information System (INIS)

Nagata, Yasushi; Hiraoka, Masahiro; Nishidai, Takehiro

2000-01-01

A computed tomography (CT) simulator is defined as a radiotherapy treatment planning (RTP) system which consists of an X-ray CT scanner, a treatment planning computer, and a marking projector. The developmental process from the introduction of an X-ray CT to a CT simulator is described in this article. After the development of the first CT simulator, several new developments in CT scanners, marking projector, and data transfer networks were introduced. CT simulator systems have recently become more widely available and are produced by more than 8 commercial companies. The advantages of a CT simulator are a shortening of overall RTP time, increased accuracy of RTP, and the possibility of 3-D conformal therapy. Clinical experience with CT simulators has accumulated over the past 10 years. Site-specific trials have been undertaken, and the clinical usefulness of CT simulators for breast cancer, maxillary cancer, nasopharyngeal cancer, orbital tumor, lung cancer and other tumors has been demonstrated. The use of CT simulators has resulted in a decrease in the complications of radiotherapy. It also appears to be an essential tool for dose escalation studies, which may permit increased local control of certain tumors. In Japan, CT simulators were in use at more than 134 (20%) of 682 radiotherapy institutions as of the end of 1998. In the USA, CT simulators were present in more than 12% of 1,542 radiotherapy centers in 1994. The CT simulator is now an essential RTP system for advanced radiotherapy. (author)

A Software Development Simulation Model of a Spiral Process

Science.gov (United States)

Mizell, Carolyn; Malone, Linda

2007-01-01

There is a need for simulation models of software development processes other than the waterfall because processes such as spiral development are becoming more and more popular. The use of a spiral process can make the inherently difficult job of cost and schedule estimation even more challenging due to its evolutionary nature, but this allows for a more flexible process that can better meet customers' needs. This paper will present a discrete event simulation model of spiral development that can be used to analyze cost and schedule effects of using such a process in comparison to a waterfall process.

Quantification of uncertainties of modeling and simulation

International Nuclear Information System (INIS)

Ma Zhibo; Yin Jianwei

2012-01-01

The principles of Modeling and Simulation (M and S) is interpreted by a functional relation, from which the total uncertainties of M and S are identified and sorted to three parts considered to vary along with the conceptual models' parameters. According to the idea of verification and validation, the space of the parameters is parted to verified and applied domains, uncertainties in the verified domain are quantified by comparison between numerical and standard results, and those in the applied domain are quantified by a newly developed extrapolating method. Examples are presented to demonstrate and qualify the ideas aimed to build a framework to quantify the uncertainties of M and S. (authors)

DEVELOPMENT OF A VIRTUAL 3D-SIMULATOR OF THE FEED PELLETING TECHNOLOGICAL PROCESS

Directory of Open Access Journals (Sweden)

N. Shcherbakov

2017-08-01

Full Text Available The process of developing a virtual 3D simulator of the process of granulation of mixed fodders is considered. The consequences of errors in the operation of press granulator operators are considered. The difficulties associated with the training of high-tech and expensive equipment operators are described. The necessity and described difficulties of acquiring practical skills of working with such equipment at the training stage are substantiated. It is argued the need to introduce computer simulators in educational institutions in order to improve the quality of the acquired knowledge, form a complex decision-making skill for future operators of technological processes. The results of a survey on improving the efficiency of management of technological processes after the introduction of simulators at enterprises are considered. The data of the simulator market and its forecasts for 2017 by regions and types of the interface used are presented. The conclusion is drawn about the growing popularity of simulators based on the 3D interface. The advantage of using the 3D interface with respect to the 2D interface is substantiated. The types of immersion in the learning environment in various simulator interfaces are considered. The vulnerabilities of the 3D simulator are noted. The goal is to develop a 3D simulator for a press granulator operator. A solution of a set of tasks is proposed to achieve this goal. The plan for creating a simulator was developed. A detailed consideration of the development stages of the simulator is given. The possibilities of using the simulator being developed are considered. The possibility of developing a simulator of emergency situations is described. The relevance of this development is justified.

Development of HTGR plant dynamics simulation code

International Nuclear Information System (INIS)

Ohashi, Kazutaka; Tazawa, Yujiro; Mitake, Susumu; Suzuki, Katsuo.

1987-01-01

Plant dynamics simulation analysis plays an important role in the design work of nuclear power plant especially in the plant safety analysis, control system analysis, and transient condition analysis. The authors have developed the plant dynamics simulation code named VESPER, which is applicable to the design work of High Temperature Engineering Test Reactor, and have been improving the code corresponding to the design changes made in the subsequent design works. This paper describes the outline of VESPER code and shows its sample calculation results selected from the recent design work. (author)

Comparative Study on Two Melting Simulation Methods: Melting Curve of Gold

International Nuclear Information System (INIS)

Liu Zhong-Li; Li Rui; Sun Jun-Sheng; Zhang Xiu-Lu; Cai Ling-Cang

2016-01-01

Melting simulation methods are of crucial importance to determining melting temperature of materials efficiently. A high-efficiency melting simulation method saves much simulation time and computational resources. To compare the efficiency of our newly developed shock melting (SM) method with that of the well-established two-phase (TP) method, we calculate the high-pressure melting curve of Au using the two methods based on the optimally selected interatomic potentials. Although we only use 640 atoms to determine the melting temperature of Au in the SM method, the resulting melting curve accords very well with the results from the TP method using much more atoms. Thus, this shows that a much smaller system size in SM method can still achieve a fully converged melting curve compared with the TP method, implying the robustness and efficiency of the SM method. (paper)

Developed Turbulence: From Full Simulations to Full Mode Reductions

NARCIS (Netherlands)

Grossmann, Siegfried; Lohse, Detlef; Reeh, Achim

1996-01-01

Developed Navier-Stokes turbulence is simulated with varying wave-vector mode reductions. The flatness and the skewness of the velocity derivative depend on the degree of mode reduction. They show a crossover towards the value of the full numerical simulation when the viscous subrange starts to be

Development of Nuclear Plant Specific Analysis Simulators with ATLAS

International Nuclear Information System (INIS)

Jakubowski, Z.; Draeger, P.; Horche, W.; Pointner, W.

2006-01-01

The simulation software ATLAS, based on the best-estimate code ATHLET, has been developed by the GRS for a range of applications in the field of nuclear plant safety analysis. Through application of versatile simulation tools and graphical interfaces the user should be able to analyse with ATLAS all essential accident scenarios. Detailed analysis simulators for several German and Russian NPPs are being constructed on the basis of ATLAS. An overview of the ATLAS is presented in the paper, describing its configuration, functions performed by main components and relationships among them. A significant part of any power plant simulator are the balance-of-plant (BOP) models, not only because all the plant transients and non-LOCA accidents can be initiated by operation of BOP systems, but also because the response of the plant to transients or accidents is strongly influenced by the automatic operation of BOP systems. Modelling aspects of BOP systems are shown in detail, also the interface between the process model and BOP systems. Special emphasis has been put on the BOP model builder based on the methodology developed in the GRS. The BOP modeler called GCSM-Generator is an object oriented tool which runs on the online expert system G2. It is equipped with utilities to edit the BOP models, to verification them and to generate a GCSM code, specific for the ATLAS. The communication system of ATLAS presents graphically the results of the simulation and allows interactively influencing the execution of the simulation process (malfunctions, manual control). Displays for communications with simulated processes and presentation of calculations results are also presented. In the framework of the verification of simulation models different tools are used e.g. the PC-codes MATHCAD for the calculation and documentation, ATLET-Input-Graphic for control of geometry data and the expert system G2 for development of BOP-Models. The validation procedure and selected analyses results

Development of Simulator Maintenance Engineer Qualification Program Draft

International Nuclear Information System (INIS)

Chung, Kyung Hun

2010-01-01

As of 2009, KHNP has currently seven full scope simulators that are used for training of Nuclear Power Plant (NPP) Operators. Well-trained Simulator Maintenance Engineers (SME) are required to support these simulators. These SMEs will maintain and address any issues identified or any changes required for keep up the simulator with their respective plant sites. These issues will be identified as Simulator Discrepancy Reports (DR) or Work Order (WO) by the simulator operation personnel in KHNP. The simulator maintenance is a very complex. The simulator consists of many areas of process and requires experts in software modeling for different processes such as Neutronics, thermohydraulics, Logics, control, Electrical systems and computer systems as well as hardware subjects such as I and C, I/O, computers, etc. All these areas need experts the subject expertise need to be divided among SME's. In other word the SME's need to be trained for different expertise as well as having different level of SME's. KHNP has seen the need to outsource the maintenance work for these complex simulators. To have one company concentrating on this work will have many benefits such as: · Provides proper and well trained experts · Maintains consistent support personnel · Maintains the maintenance history for the simulator · Coordinates and Maintains the knowledge in house · The simulator maintenance will be consistent In order to accomplish the goals, KEPCO RI has recognized that there is a need for a program to adequately train and qualify the SME's. KEPCO RI and GSE, which has provided 6 simulators among 7 NPP simulators in Korea, have jointly developed this Simulator Maintenance Engineer Qualification Program (SMEQP). After issue of this plan, KEPCO RI will maintain and modify as needed periodically to meet the goals and purpose of the plan

The JINR Tier1 Site Simulation for Research and Development Purposes

Directory of Open Access Journals (Sweden)

Korenkov V.

2016-01-01

A system for grid and cloud services simulation is developed at LIT (JINR, Dubna. This simulation system is focused on improving the effciency of the grid/cloud structures development by using the work quality indicators of some real system. The development of such kind of software is very important for making a new grid/cloud infrastructure for such big scientific experiments like the JINR Tier1 site for WLCG. The simulation of some processes of the Tier1 site is considered as an example of our application approach.

Cosmicflows Constrained Local UniversE Simulations

Science.gov (United States)

Sorce, Jenny G.; Gottlöber, Stefan; Yepes, Gustavo; Hoffman, Yehuda; Courtois, Helene M.; Steinmetz, Matthias; Tully, R. Brent; Pomarède, Daniel; Carlesi, Edoardo

2016-01-01

This paper combines observational data sets and cosmological simulations to generate realistic numerical replicas of the nearby Universe. The latter are excellent laboratories for studies of the non-linear process of structure formation in our neighbourhood. With measurements of radial peculiar velocities in the local Universe (cosmicflows-2) and a newly developed technique, we produce Constrained Local UniversE Simulations (CLUES). To assess the quality of these constrained simulations, we compare them with random simulations as well as with local observations. The cosmic variance, defined as the mean one-sigma scatter of cell-to-cell comparison between two fields, is significantly smaller for the constrained simulations than for the random simulations. Within the inner part of the box where most of the constraints are, the scatter is smaller by a factor of 2 to 3 on a 5 h-1 Mpc scale with respect to that found for random simulations. This one-sigma scatter obtained when comparing the simulated and the observation-reconstructed velocity fields is only 104 ± 4 km s-1, I.e. the linear theory threshold. These two results demonstrate that these simulations are in agreement with each other and with the observations of our neighbourhood. For the first time, simulations constrained with observational radial peculiar velocities resemble the local Universe up to a distance of 150 h-1 Mpc on a scale of a few tens of megaparsecs. When focusing on the inner part of the box, the resemblance with our cosmic neighbourhood extends to a few megaparsecs (<5 h-1 Mpc). The simulations provide a proper large-scale environment for studies of the formation of nearby objects.

A Software Development Simulation Model of a Spiral Process

OpenAIRE

Carolyn Mizell; Linda Malone

2009-01-01

This paper will present a discrete event simulation model of a spiral development lifecycle that can be used to analyze cost and schedule effects of using such a process in comparison to a waterfall process. There is a need for simulation models of software development processes other than the waterfall due to new processes becoming more widely used in order to overcome the limitations of the traditional waterfall lifecycle. The use of a spiral process can make the inherently difficult job of...

Agent Behavior-Based Simulation Study on Mass Collaborative Product Development Process

Directory of Open Access Journals (Sweden)

Shuo Zhang

2015-01-01

Full Text Available Mass collaborative product development (MCPD benefits people by high innovation products with lower cost and shorter lead time due to quick development of group innovation, Internet-based customization, and prototype manufacturing. Simulation is an effective way to study the evolution process and therefore to guarantee the success of MCPD. In this paper, an agent behavior-based simulation approach of MCPD is developed, which models the MCPD process as the interactive process of design agents and the environment objects based on Complex Adaptive System (CAS theory. Next, the structure model of design agent is proposed, and the modification and collaboration behaviors are described. Third, the agent behavior-based simulation flow of MCPD is designed. At last, simulation experiments are carried out based on an engineering case of mobile phone design. The experiment results show the following: (1 the community scale has significant influence on MCPD process; (2 the simulation process can explicitly represent the modification and collaboration behaviors of design agents; (3 the community evolution process can be observed and analyzed dynamically based on simulation data.

A model for mentoring newly-appointed nurse educators in nursing education institutions in South Africa

Directory of Open Access Journals (Sweden)

Eunice Seekoe

2014-02-01

Full Text Available Background: South Africa transformed higher education through the enactment of the Higher Education Act (No. 101 of 1997. The researcher identified the need to develop a model for the mentoring of newly-appointed nurse educators in nursing education institutions in South Africa. Objectives: To develop and describe the model for mentoring newly-appointed nurse educators in nursing education institutions in South Africa. Method: A qualitative and theory-generating design was used (following empirical findings regarding needs analysis in order to develop the model. The conceptualisation of the framework focused on the context, content, process and the theoretical domains that influenced the model. Ideas from different theories were borrowed from and integrated with the literature and deductive and inductive strategies were applied. Results: The structure of the model is multidimensional and complex in nature (macro, mesoand micro based on the philosophy of reflective practice, competency-based practice andcritical learning theories. The assumptions are in relation to stakeholders, context, mentoring, outcome, process and dynamic. The stakeholders are the mentor and mentee within an interactive participatory relationship. The mentoring takes place within the process with a sequence of activities such as relationship building, development, engagement, reflective process and assessment. Capacity building and empowerment are outcomes of mentoring driven by motivation. Conclusion: The implication for nurse managers is that the model can be used to develop mentoring programmes for newly-appointed nurse educators.

Los Alamos Plutonium Facility newly generated TRU waste certification

International Nuclear Information System (INIS)

Gruetzmacher, K.; Montoya, A.; Sinkule, B.; Maez, M.

1997-01-01

This paper presents an overview of the activities being planned and implemented to certify newly generated contact handled transuranic (TRU) waste produced by Los Alamos National Laboratory's (LANL's) Plutonium Facility. Certifying waste at the point of generation is the most important cost and labor saving step in the WIPP certification process. The pedigree of a waste item is best known by the originator of the waste and frees a site from expensive characterization activities such as those associated with legacy waste. Through a cooperative agreement with LANLs Waste Management Facility and under the umbrella of LANLs WIPP-related certification and quality assurance documents, the Plutonium Facility will be certifying its own newly generated waste. Some of the challenges faced by the Plutonium Facility in preparing to certify TRU waste include the modification and addition of procedures to meet WIPP requirements, standardizing packaging for TRU waste, collecting processing documentation from operations which produce TRU waste, and developing ways to modify waste streams which are not certifiable in their present form

Development of Reactor TRIGA PUSPATI Simulator for Education and Training

International Nuclear Information System (INIS)

Mohd Sabri Minhat; Zarina Masood; Muhammad Rawi Mohamed Zin

2016-01-01

The real-time simulator for Reactor TRIGA PUSPATI (RTP) which is under development. The main purpose of this simulator is operator training and a dynamic test bed (DTB) to test and validate the control logics in reactor regulating system (RRS) of RTP. The simulator configuration is divided into hardware and software. The simulator hardware consists of a host computer, operator station, a network switch, control rod drive mechanism and a large display panel. The RTP hardwired panel is replicated similar to real console. The software includes a mathematical model includes reactor kinetics and thermal-hydraulics that implements plant dynamics in real-time using LabVIEW, an instructor station module work as host computer that manages user instructions, and a human machine interface module as a graphical user interface which is used in the real RTP plant. The developed TRIGA reactor simulators are installed in the Malaysian Nuclear Agency nuclear training center for reactor operator training. To use the simulator as a dynamic test-bed, the reactor regulating system modeling software of the simulator was replaced by actual RRS cabinet which is consist of Programmable Logic Controller (PLC) S7-1500, and was interfaced using a hard-wired and network-based interface. RRS cabinet generates control signals for reactor power control based on the various feedback signals from DTB such as neutron detector signal and control rod positions, and the DTB runs plant dynamics based on the RRS control signals. Thus the Hardware-In-the-Loop Simulation between RRS and the emulated plant (DTB) has been implemented and tested in this configuration. Normal and abnormal case test have been emulated for this project. In conclusion, the functions and the control performance of the developed RTP dynamic test bed simulator have been tested showing reasonable and acceptable results. (author)

Phenology of Lymantria monacha (Lepidoptera:Lymantriidae) laboratory reared on spruce foliage or a newly developed artificial diet

Science.gov (United States)

Melody A. Keena; Alice Vandel; Oldrich. Pultar

2010-01-01

Lymantria monacha (L.) (Lepidoptera: Lymantriidae) is a Eurasian pest of conifers that has potential for accidental introduction into North America. The phenology over the entire life cycle for L. monacha individuals from the Czech Republic was compared on Picea glauca (Moench) Voss (white spruce) and a newly...

Problems faced by newly diagnosed diabetes mellitus patients at ...

African Journals Online (AJOL)

Diabetes mellitus can be a frightening experience for newly diagnosed patients. The aim of this study was to determine and describe the problems faced by newly diagnosed diabetes mellitus patients at primary healthcare facilities at Mopani district, Limpopo Province. A qualitative, descriptive and contextual research ...

Development of a prototype graphic simulation program for severe accident training

Energy Technology Data Exchange (ETDEWEB)

Kim, Ko Ryu; Jeong, Kwang Sub; Ha, Jae Joo

2000-05-01

This is a report of the development process and related technologies of severe accident graphic simulators, required in industrial severe accident management and training. Here, we say 'a severe accident graphic simulator' as a graphics add-in system to existing calculation codes, which can show the severe accident phenomena dynamically on computer screens and therefore which can supplement one of main defects of existing calculation codes. With graphic simulators it is fairly easy to see the total behavior of nuclear power plants, where it was very difficult to see only from partial variable numerical information. Moreover, the fast processing and control feature of a graphic simulator can give some opportunities of predicting the severe accident advancement among several possibilities, to one who is not an expert. Utilizing graphic simulators' we expect operators' and TSC members' physical phenomena understanding enhancement from the realistic dynamic behavior of plants. We also expect that severe accident training course can gain better training effects using graphic simulator's control functions and predicting capabilities, and therefore we expect that graphic simulators will be effective decision-aids tools both in sever accident training course and in real severe accident situations. With these in mind, we have developed a prototype graphic simulator having surveyed related technologies, and from this development experiences we have inspected the possibility to build a severe accident graphic simulator. The prototype graphic simulator is developed under IBM PC WinNT environments and is suited to Uljin 3and4 nuclear power plant. When supplied with adequate severe accident scenario as an input, the prototype can provide graphical simulations of plant safety systems' dynamic behaviors. The prototype is composed of several different modules, which are phenomena display module, MELCOR data interface module and graphic database

Newly graduated nurses' use of knowledge sources in clinical decision-making

DEFF Research Database (Denmark)

Voldbjerg, Siri Lygum; Grønkjaer, Mette; Wiechula, Rick

2017-01-01

AIMS AND OBJECTIVES: To explore which knowledge sources newly graduated nurses' use in clinical decision-making and why and how they are used. BACKGROUND: In spite of an increased educational focus on skills and competencies within evidence based practice newly graduated nurses' ability to use...... approaches to strengthen the knowledgebase used in clinical decision-making. DESIGN AND METHODS: Ethnographic study using participant-observation and individual semi-structured interviews of nine Danish newly graduated nurses in medical and surgical hospital settings. RESULTS: Newly graduates use...... in clinical decision-making. If newly graduates are to be supported in an articulate and reflective use of a variety of sources, they have to be allocated to experienced nurses who model a reflective, articulate and balanced use of knowledge sources. This article is protected by copyright. All rights reserved....

Development of steam explosion simulation code JASMINE

Energy Technology Data Exchange (ETDEWEB)

Moriyama, Kiyofumi; Yamano, Norihiro; Maruyama, Yu; Kudo, Tamotsu; Sugimoto, Jun [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Nagano, Katsuhiro; Araki, Kazuhiro

1995-11-01

A steam explosion is considered as a phenomenon which possibly threatens the integrity of the containment vessel of a nuclear power plant in a severe accident condition. A numerical calculation code JASMINE (JAeri Simulator for Multiphase INteraction and Explosion) purposed to simulate the whole process of steam explosions has been developed. The premixing model is based on a multiphase flow simulation code MISTRAL by Fuji Research Institute Co. In JASMINE code, the constitutive equations and the flow regime map are modified for the simulation of premixing related phenomena. The numerical solution method of the original code is succeeded, i.e. the basic equations are discretized semi-implicitly, BCGSTAB method is used for the matrix solver to improve the stability and convergence, also TVD scheme is applied to capture a steep phase distribution accurately. Test calculations have been performed for the conditions correspond to the experiments by Gilbertson et al. and Angelini et al. in which mixing of solid particles and water were observed in iso-thermal condition and with boiling, respectively. (author).

Development of steam explosion simulation code JASMINE

International Nuclear Information System (INIS)

Moriyama, Kiyofumi; Yamano, Norihiro; Maruyama, Yu; Kudo, Tamotsu; Sugimoto, Jun; Nagano, Katsuhiro; Araki, Kazuhiro.

1995-11-01

A steam explosion is considered as a phenomenon which possibly threatens the integrity of the containment vessel of a nuclear power plant in a severe accident condition. A numerical calculation code JASMINE (JAeri Simulator for Multiphase INteraction and Explosion) purposed to simulate the whole process of steam explosions has been developed. The premixing model is based on a multiphase flow simulation code MISTRAL by Fuji Research Institute Co. In JASMINE code, the constitutive equations and the flow regime map are modified for the simulation of premixing related phenomena. The numerical solution method of the original code is succeeded, i.e. the basic equations are discretized semi-implicitly, BCGSTAB method is used for the matrix solver to improve the stability and convergence, also TVD scheme is applied to capture a steep phase distribution accurately. Test calculations have been performed for the conditions correspond to the experiments by Gilbertson et al. and Angelini et al. in which mixing of solid particles and water were observed in iso-thermal condition and with boiling, respectively. (author)

Test beam evaluation of newly developed n-in-p planar pixel sensors for use in a high radiation environment

Energy Technology Data Exchange (ETDEWEB)

Kimura, K., E-mail: kimihiko@hep.phys.titech.ac.jp [Institute of Science and Engineering, Tokyo Institute of Technology, Ookayama 2-12-1, Meguro-ku, Tokyo 152-8551 (Japan); Yamaguchi, D.; Motohashi, K. [Institute of Science and Engineering, Tokyo Institute of Technology, Ookayama 2-12-1, Meguro-ku, Tokyo 152-8551 (Japan); Nakamura, K.; Unno, Y. [Institute of Particle and Nuclear Study, KEK, Oho 1-1, Tsukuba, Ibaraki 305-0801 (Japan); Jinnouchi, O. [Institute of Science and Engineering, Tokyo Institute of Technology, Ookayama 2-12-1, Meguro-ku, Tokyo 152-8551 (Japan); Altenheiner, S. [Experimentelle Physik IV, Technische Universität Dortmund, 44221 Dortmund (Germany); Blue, A. [School of Physics and Astronomy, University of Glasgow, Glasgow, G12 8QQ, Scotland (United Kingdom); Bomben, M. [CNRS/IN2P3 (France); Laboratoire de physique nucléaire et de hautes energies (LPNHE), Univ. Paris-UMPC, 4 Place Jussieu, 75005 Paris (France); Univ. Paris Diderot (France); Butter, A. [LAL, University Paris-Sud (France); CNRS/IN2P3 (France); Université Paris-Saclay, Orsay (France); Cervelli, A. [Universität Bern, Laboratory for High Energy Physics, Sidlerstrasse 55, CH-3012 Bern (Switzerland); Crawley, S. [School of Physics and Astronomy, University of Glasgow, Glasgow, G12 8QQ, Scotland (United Kingdom); Ducourthial, A. [CNRS/IN2P3 (France); Laboratoire de physique nucléaire et de hautes energies (LPNHE), Univ. Paris-UMPC, 4 Place Jussieu, 75005 Paris (France); Univ. Paris Diderot (France); Gisen, A. [Experimentelle Physik IV, Technische Universität Dortmund, 44221 Dortmund (Germany); Hagihara, M. [Institute of Pure and Applied Sciences, University of Tsukuba, Tsukuba, Ibaraki 305-8751 (Japan); and others

2016-09-21

Radiation-tolerant n-in-p planar pixel sensors have been under development in cooperation with Hamamatsu Photonics K.K. (HPK). This is geared towards applications in high-radiation environments, such as for the future Inner Tracker (ITk) placed in the innermost part of the ATLAS detector in the high luminosity LHC (HL-LHC) experiment. Prototypes of those sensors have been produced, irradiated, and evaluated over the last few years. In the previous studies, it was reported that significant drops in the detection efficiency were observed after irradiation, especially under bias structures. The bias structures are made up of poly-Si or Al bias rails and poly-Si bias resistors. The structure is implemented on the sensors to allow quality checks to be performed before the bump-bonding process, and to ensure that charge generated in floating pixels due to non-contacting or missing bump-bonds is dumped in a controlled way in order to avoid noise. To minimize the efficiency drop, several new pixel structures have been designed with bias rails and bias resistors relocated. Several test beams have been carried out to evaluate the drops in the detection efficiency of the new sensor structures after irradiation. Newly developed sensor modules were irradiated with proton-beams at the Cyclotron and Radio-Isotope Center (CYRIC) in Tohoku University to see the effect of sensor-bulk damage and surface charge-up. An irradiation with γ-rays was also carried out at Takasaki Advanced Radiation Research Center, with the goal of decoupling the effect of surface charge-up from that of bulk damage. Those irradiated sensors have been evaluated with particle beams at DESY and CERN. Comparison between different sensor structures confirmed significant improvements in minimizing efficiency loss under the bias structures after irradiation. The results from γ-irradiation also enabled cross-checking the results of a semiconductor technology simulation program (TCAD). - Highlights: • The

Newly graduated nurses' occupational commitment and its associations with professional competence and work-related factors.

Science.gov (United States)

Numminen, Olivia; Leino-Kilpi, Helena; Isoaho, Hannu; Meretoja, Riitta

2016-01-01

To explore newly graduated nurses' occupational commitment and its associations with their self-assessed professional competence and other work-related factors. As a factor affecting nurse turnover, newly graduated nurses' occupational commitment and its associations with work-related factors needs exploring to retain adequate workforce. Nurses' commitment has mainly been studied as organisational commitment, but newly graduated nurses' occupational commitment and its association with work-related factors needs further studying. This study used descriptive, cross-sectional, correlation design. A convenience sample of 318 newly graduated nurses in Finland participated responding to an electronic questionnaire. Statistical software, NCSS version 9, was used in data analysis. Frequencies, percentages, ranges, means and standard deviations summarised the data. Multivariate Analyses of Variance estimated associations between occupational commitment and work-related variables. IBM SPSS Amos version 22 estimated the model fit of Occupational Commitment Scale and Nurse Competence Scale. Newly graduated nurses' occupational commitment was good, affective commitment reaching the highest mean score. There was a significant difference between the nurse groups in favour of nurses at higher competence levels in all subscales except in limited alternatives occupational commitment. Multivariate analyses revealed significant associations between subscales of commitment and competence, turnover intentions, job satisfaction, earlier professional education and work sector, competence counting only through affective dimension. The association between occupational commitment and low turnover intentions and satisfaction with nursing occupation was strong. Higher general competence indicated higher overall occupational commitment. Managers' recognition of the influence of all dimensions of occupational commitment in newly graduated nurses' professional development is important. Follow

Ethical climate and nurse competence - newly graduated nurses' perceptions.

Science.gov (United States)

Numminen, Olivia; Leino-Kilpi, Helena; Isoaho, Hannu; Meretoja, Riitta

2015-12-01

is also a need for knowledge of newly graduated nurses' views of factors which act as enhancers or barriers to positive ethical climates to develop. Interventions, continuing education courses, and discussions designed to promote positive ethical climates should be developed for managers, nurses, and multi-professional teams. © The Author(s) 2014.

Practices influenced by policy? An exploration of newly hired science teachers at sites in South Africa and the United States

Science.gov (United States)

Navy, S. L.; Luft, J. A.; Toerien, R.; Hewson, P. W.

2018-05-01

In many parts of the world, newly hired science teachers' practices are developing in a complex policy environment. However, little is known about how newly hired science teachers' practices are enacted throughout a cycle of instruction and how these practices can be influenced by macro-, meso-, and micro-policies. Knowing how policies impact practice can result in better policies or better support for certain policies in order to enhance the instruction of newly hired teachers. This comparative study investigated how 12 newly hired science teachers at sites in South Africa (SA) and the United States (US) progressed through an instructional cycle of planning, teaching, and reflection. The qualitative data were analysed through beginning teacher competency frameworks, the cycle of instruction, and institutional theory. Data analysis revealed prevailing areas of practice and connections to levels of policy within the instructional cycle phases. There were some differences between the SA and US teachers and among first-, second-, and third-year teachers. More importantly, this study indicates that newly hired teachers are susceptible to micro-policies and are progressively developing their practice. It also shows the importance of meso-level connectors. It suggests that teacher educators and policy makers must consider how to prepare and support newly hired science teachers to achieve the shared global visions of science teaching.

NEWLY-PACKAGED BALI TOURIST PERFORMING ARTS IN THE PERSPECTIVE OF CULTURAL STUDIES

Directory of Open Access Journals (Sweden)

Ni Made Ruastiti

2012-11-01

Full Text Available This research is focused on the newly packaged tourist performing arts; they are anew concept and seem to be different from the general tourist performing arts. They arepackaged from various components of Balinese arts and managed as large scale-touristperforming arts in terms of materials, space, and time of their performances. The researchercalls them new types of Bali tourist performing arts because how they are presented isnew and different from the traditional tourist performing arts which are simply performed.In this research, the newly-packaged performing arts are analyzed in the perspective ofcultural studies.The research was carried out at three palaces in Bali; they are Mengwi Palace inBadung regency, Anyar Palace at Kerambitan, Tabanan regency, and Banyuning Palace atBongkasa, Badung regency. There are three main problems to be discussed: firstly, how dothe tourist performing arts emerge in all the palaces? Secondly, are they related to thetourist industry developed in the palaces?, thirdly, what is the impact and meaning of themfor the sake of the palaces, society, and Balinese culture? The researcher uses a qualitativemethod and an interdisciplinary approach as characteristics of cultural studies. The theoriesused are hegemony, deconstruction, and structuration.The result shows that the tourism development at all the palaces has made the localsociety become more critical. The money-oriented economy based on the spirit of gettingbenefit has made the emergence of comodification in all sectors of life. The emergence oftourist industry at the palaces has led to the idea of showing all of the useful art and culturalpotentials which at the palaces and their surroundings. Theoretically, the palaces can bestated to have deconstructed the concept of presenting the Bali tourist performing arts into anew one, that is, “the newly packaged Bali tourist performing arts”.It has been observed that all the palaces have developed t “Newly

Application of simulation experiments to fusion materials development

International Nuclear Information System (INIS)

Nolfi, F.V. Jr.; Li, C.Y.

1978-01-01

One of the major problems in the development of structural alloys for use in magnetic fusion reactors (MFRs) is the lack of suitable materials testing facilities. This is because operating fusion reactors, even of the experimental size, do not exist. A primary task in the early stages of MFR alloy development will be to adapt currently available irradiation facilities for use in materials development. Thus, it is generally recognized that, at least for the next ten years, studies of irradiation effects in an MFR environment on the microstructure and mechanical properties of structural materials must utilize ion and fission neutron simulations. Special problems will arise because, in addition to displacement damage, an MFR radiation environment will produce, in candidate structural materials, higher and more significant concentrations of gaseous nuclear transmutation products, e.g., helium and hydrogen, than found in a fast breeder reactor. These effects must be taken into account when simulation techniques are employed, since they impact heavily on irradiation microstructure development and, hence, mechanical properties

On Challenges for Hypersonic Turbulent Simulations

International Nuclear Information System (INIS)

Yee, H.C.; Sjogreen, B.

2009-01-01

This short note discusses some of the challenges for design of suitable spatial numerical schemes for hypersonic turbulent flows, including combustion, and thermal and chemical nonequilibrium flows. Often, hypersonic turbulent flows in re-entry space vehicles and space physics involve mixed steady strong shocks and turbulence with unsteady shocklets. Material mixing in combustion poses additional computational challenges. Proper control of numerical dissipation in numerical methods beyond the standard shock-capturing dissipation at discontinuities is an essential element for accurate and stable simulations of the subject physics. On one hand, the physics of strong steady shocks and unsteady turbulence/shocklet interactions under the nonequilibrium environment is not well understood. On the other hand, standard and newly developed high order accurate (fourth-order or higher) schemes were developed for homogeneous hyperbolic conservation laws and mixed hyperbolic and parabolic partial differential equations (PDEs) (without source terms). The majority of finite rate chemistry and thermal nonequilibrium simulations employ methods for homogeneous time-dependent PDEs with a pointwise evaluation of the source terms. The pointwise evaluation of the source term might not be the best choice for stability, accuracy and minimization of spurious numerics for the overall scheme

Efficacy of Intra-articular Injection of a Newly Developed Plasma Rich in Growth Factor (PRGF) Versus Hyaluronic Acid on Pain and Function of Patients with Knee Osteoarthritis: A Single-Blinded Randomized Clinical Trial.

Science.gov (United States)

Raeissadat, Seyed Ahmad; Rayegani, Seyed Mansoor; Ahangar, Azadeh Gharooee; Abadi, Porya Hassan; Mojgani, Parviz; Ahangar, Omid Gharooi

2017-01-01

Knee osteoarthritis is the most common joint disease. We aimed to compare the efficacy and safety of intra-articular injection of a newly developed plasma rich in growth factor (PRGF) versus hyaluronic acid (HA) on pain and function of patients with knee osteoarthritis. In this single-blinded randomized clinical trial, patients with symptomatic osteoarthritis of knee were assigned to receive 2 intra-articular injections of our newly developed PRGF in 3 weeks or 3 weekly injections of HA. Our primary outcome was the mean change from baseline until 2 and 6 months post intervention in scores of visual analog scale, Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC), and Lequesne index. We used analysis of variance for repeated-measures statistical test. A total of 69 patients entered final analysis. The mean age of patients was 58.2 ± 7.41 years and 81.2% were women. In particular, total WOMAC index decreased from 42.9 ± 13.51 to 26.8 ± 13.45 and 24.4 ± 16.54 at 2 and 6 months in the newly developed PRGF group (within subjects P  = .001), and from 38.8 ± 12.62 to 27.8 ± 11.01 and 27.4 ± 11.38 at 2 and 6 months in the HA group (within subjects P  = .001), respectively (between subjects P  = .631). There was no significant difference between PRGF and HA groups in patients' satisfaction and minor complications of injection, whereas patients in HA group reported significantly lower injection-induced pain. In 6 months follow up, our newly developed PRGF and HA, both are effective options to decrease pain and improvement of function in patients with symptomatic mild to moderate knee osteoarthritis.

Development of a Cardiovascular Simulator for Studying Pulse Diagnosis Mechanisms

Directory of Open Access Journals (Sweden)

Min Jang

2017-01-01

Full Text Available This research was undertaken to develop a cardiovascular simulator for use in the study of pulse diagnosis. The physical (i.e., pulse wave transmission and reflection and physiological (i.e., systolic and diastolic pressure, pulse pressure, and mean pressure characteristics of the radial pulse wave were reproduced by our simulator. The simulator consisted of an arterial component and a pulse-generating component. Computer simulation was used to simplify the arterial component while maintaining the elastic modulus and artery size. To improve the reflected wave characteristics, a palmar arch was incorporated within the simulator. The simulated radial pulse showed good agreement with clinical data.

Model for Simulating a Spiral Software-Development Process

Science.gov (United States)

Mizell, Carolyn; Curley, Charles; Nayak, Umanath

2010-01-01

A discrete-event simulation model, and a computer program that implements the model, have been developed as means of analyzing a spiral software-development process. This model can be tailored to specific development environments for use by software project managers in making quantitative cases for deciding among different software-development processes, courses of action, and cost estimates. A spiral process can be contrasted with a waterfall process, which is a traditional process that consists of a sequence of activities that include analysis of requirements, design, coding, testing, and support. A spiral process is an iterative process that can be regarded as a repeating modified waterfall process. Each iteration includes assessment of risk, analysis of requirements, design, coding, testing, delivery, and evaluation. A key difference between a spiral and a waterfall process is that a spiral process can accommodate changes in requirements at each iteration, whereas in a waterfall process, requirements are considered to be fixed from the beginning and, therefore, a waterfall process is not flexible enough for some projects, especially those in which requirements are not known at the beginning or may change during development. For a given project, a spiral process may cost more and take more time than does a waterfall process, but may better satisfy a customer's expectations and needs. Models for simulating various waterfall processes have been developed previously, but until now, there have been no models for simulating spiral processes. The present spiral-process-simulating model and the software that implements it were developed by extending a discrete-event simulation process model of the IEEE 12207 Software Development Process, which was built using commercially available software known as the Process Analysis Tradeoff Tool (PATT). Typical inputs to PATT models include industry-average values of product size (expressed as number of lines of code

Developing a fast simulator for irradiated silicon detectors

CERN Document Server

Diez Gonzalez-Pardo, Alvaro

2015-01-01

Simulation software for irradiated silicon detectors has been developed on the basis of an already existing C++ simulation software called TRACS[1]. This software has been already proven useful in understanding non-irradiated silicon diodes and microstrips. In addition a wide variety of user-focus features has been implemented to improve on TRACS flexibility. Such features include an interface to allow any program to leverage TRACS functionalities, a configuration file and improved documentation.

Microstructural development during the quenching and partitioning process in a newly designed low-carbon steel

Energy Technology Data Exchange (ETDEWEB)

Santofimia, M.J., E-mail: m.j.santofimianavarro@tudelft.nl [Materials Innovation Institute (M2i), Mekelweg 2, 2628 CD Delft (Netherlands); Department of Materials Science and Engineering, Delft University of Technology, Mekelweg 2, 2628 CD Delft (Netherlands); Zhao, L. [Materials Innovation Institute (M2i), Mekelweg 2, 2628 CD Delft (Netherlands); Department of Materials Science and Engineering, Delft University of Technology, Mekelweg 2, 2628 CD Delft (Netherlands); Petrov, R. [Department of Metallurgy and Materials Science, Ghent University, Technologiepark 903, 9052 Ghent (Belgium); Department of Materials Science and Engineering, Delft University of Technology, Mekelweg 2, 2628 CD Delft (Netherlands); Kwakernaak, C.; Sloof, W.G.; Sietsma, J. [Department of Materials Science and Engineering, Delft University of Technology, Mekelweg 2, 2628 CD Delft (Netherlands)

2011-09-15

This paper presents a detailed characterization of the microstructural development of a new quenching and partitioning (Q and P) steel. Q and P treatments, starting from full austenitization, were applied to the developed steel, leading to microstructures containing volume fractions of retained austenite of up to 0.15. The austenite was distributed as films in between the martensite laths. Analysis demonstrates that, in this material, stabilization of austenite can be achieved at significantly shorter time scales via the Q and P route than is possible via a bainitic isothermal holding. The results showed that the thermal stabilization of austenite during the partitioning step is not necessarily accompanied by a significant expansion of the material. This implies that the process of carbon partitioning from martensite to austenite occurs across low-mobility martensite-austenite interfaces. The amount of martensite formed during the first quench has been quantified. Unlike martensite formed in the final quench, this martensite was found to be tempered during partitioning. Measured volume fractions of retained austenite after different treatments were compared with simulations using model descriptions for carbon partitioning from martensite to austenite. Simulation results confirmed that the carbon partitioning takes place at low-mobility martensite-austenite interfaces.

Software Development Processes Applied to Computational Icing Simulation

Science.gov (United States)

Levinson, Laurie H.; Potapezuk, Mark G.; Mellor, Pamela A.

1999-01-01

The development of computational icing simulation methods is making the transition form the research to common place use in design and certification efforts. As such, standards of code management, design validation, and documentation must be adjusted to accommodate the increased expectations of the user community with respect to accuracy, reliability, capability, and usability. This paper discusses these concepts with regard to current and future icing simulation code development efforts as implemented by the Icing Branch of the NASA Lewis Research Center in collaboration with the NASA Lewis Engineering Design and Analysis Division. With the application of the techniques outlined in this paper, the LEWICE ice accretion code has become a more stable and reliable software product.

Initial Development of a Quadcopter Simulation Environment for Auralization

Science.gov (United States)

Christian, Andrew; Lawrence, Joseph

2016-01-01

This paper describes a recently created computer simulation of quadcopter flight dynamics for the NASA DELIVER project. The goal of this effort is to produce a simulation that includes a number of physical effects that are not usually found in other dynamics simulations (e.g., those used for flight controller development). These effects will be shown to have a significant impact on the fidelity of auralizations - entirely synthetic time-domain predictions of sound - based on this simulation when compared to a recording. High-fidelity auralizations are an important precursor to human subject tests that seek to understand the impact of vehicle configurations on noise and annoyance.

Development of a virtual training simulator for a challenging refurbishment task

International Nuclear Information System (INIS)

Mort, P.E.

1996-01-01

An overview is presented of the technology, developed by British Nuclear Fuels Limited (BNFL), to create a virtual training simulator for refurbishment tasks. It focuses on the Raffinate Project, a challenging plant modification take, performed remotely, during which component removal, welding and installation of new components are all undertaken. The Training Simulator developed required fast multiprocessor computing with system intercommunication. Operators responded well to the Training Simulator and further improvements to the system are underway. (UK)

Demonstration of glucose-6-phosphate dehydrogenase in rat Kupffer cells by a newly-developed ultrastructural enzyme-cytochemistry

Directory of Open Access Journals (Sweden)

S Matsubara

2009-06-01

Full Text Available Although various tissue macrophages possess high glucose- 6-phosphate dehydrogenase (G6PD activity, which is reported to be closely associated with their phagocytotic/bactericidal function, the fine subcellular localization of this enzyme in liver resident macrophages (Kupffer cells has not been determined.We have investigated the subcellular localization of G6PD in Kupffer cells in rat liver, using a newly developed enzyme-cytochemical (copper-ferrocyanide method. Electron-dense precipitates indicating G6PD activity were clearly visible in the cytoplasm and on the cytosolic side of the endoplasmic reticulum of Kupffer cells. Cytochemical controls ensured specific detection of the enzymatic activity. Rat Kupffer cells abundantly possessed enzyme-cytochemically detectable G6PD activity. Kupffer cell G6PD may play a role in liver defense by delivering NADPH to NADPH-dependent enzymes. G6PD enzyme-cytochemistry may be a useful tool for the study of Kupffer cell functions.

R/D and implement of temper bead welding as newly developed maintenance technique in nuclear power plant

International Nuclear Information System (INIS)

Hirano, Shinro; Sera, Takehiko; Chigusa, Naoki; Okimura, Koji; Nishimoto, Kazutoshi

2011-01-01

Japanese government has recently addressed a policy to increase capacity factor of existing nuclear PPs to achieve the goal to decrease the emission of CO 2 . Numerous preventive measures have taken in nuclear power plants to minimize the risk of unexpected long shutdown. Newly developed mitigation measures or repair methods need to be qualified to satisfy regulatory standards, before it is implemented to nuclear power plants. The qualification process needs to comply regulatory standards though it may consume time to go through each of the required steps. This paper describes such cases namely ambient temper-bead welding and clarifies the issues that need to be resolved regarding qualification process. The qualification process for new methods that has not been prescribed in regulatory standards temporarily completed by go through confirm testing by JAPEIC, RNP and issuance of no action letter in rush. Currently, the qualification process can only be applied on limited area so generalized qualification process needs to be established. (author)

Testability, Test Automation and Test Driven Development for the Trick Simulation Toolkit

Science.gov (United States)

Penn, John

2014-01-01

This paper describes the adoption of a Test Driven Development approach and a Continuous Integration System in the development of the Trick Simulation Toolkit, a generic simulation development environment for creating high fidelity training and engineering simulations at the NASA Johnson Space Center and many other NASA facilities. It describes the approach, and the significant benefits seen, such as fast, thorough and clear test feedback every time code is checked into the code repository. It also describes an approach that encourages development of code that is testable and adaptable.

Students as Simulation Designers and Developers--Using Computer Simulations for Teaching Boundary Layer Processes.

Science.gov (United States)

Johnson, Tristan E.; Clayson, Carol Anne

As technology developments seek to improve learning, researchers, developers, and educators seek to understand how technological properties impact performance. This paper delineates how a traditional science course is enhanced through the use of simulation projects directed by the students themselves as a means to increase their level of knowledge…

10-GHz return-to-zero pulse source tunable in wavelength with a single- or multiwavelength output based on four-wave mixing in a newly developed highly nonlinear fiber

DEFF Research Database (Denmark)

Clausen, A. T.; Oxenlowe, L.; Peucheret, Christophe

2001-01-01

In this letter, a novel scheme for a wavelength-tunable pulse source (WTPS) is proposed and characterized. It is based on four-wave mixing (FWM) in a newly developed highly nonlinear fiber between a return-to-zero (RZ) pulsed signal at a fixed wavelength and a continuous wave probe tunable...

Mechanism and application of a newly developed pressure casting process: horizontal squeeze casting

Directory of Open Access Journals (Sweden)

Li Peijie

2014-07-01

Full Text Available Compared to traditional high-pressure die casting (HPDC, horizontal squeeze casting (HSC is a more promising way to fabricate high-integrity castings, owing to a reduced number of gas and shrinkage porosities produced in the casting. In this paper, the differences between HSC and HPDC are assessed, through which it is shown that the cavity filling velocity and the size of the gating system to be the most notable differences. Equipment development and related applications are also reviewed. Furthermore, numerical simulation is used to analyze the three fundamental characteristics of HSC: slow cavity filling, squeeze feeding and slow sleeve filling. From this, a selection principle is given based on the three related critical casting parameters: cavity filling velocity, gate size and sleeve filling velocity. Finally, two specific applications of HSC are introduced, and the future direction of HSC development is discussed.

PREVALENCE OF SLEEP DISORDERED BREATHING IN PATIENTS WITH NEWLY DIAGNOSED ACROMEGALY

Directory of Open Access Journals (Sweden)

U. A. Tsoy

2014-01-01

Full Text Available Background: Obstructive sleep disordered breathing or obstructive sleep apnea (OSA is the most common respiratory impairment in acromegaly. OSA is bound up with heightened cardiovascular mortality. Aim: Тo study frequency, features, and structure of sleep disordered breathing in patients with newly diagnosed acromegaly and to elucidate the factors influencing their development. Materials and methods: 38 patients (10 men, 28 women, median age 53 (28-76 years, median body mass index (BMI 29 (19.9-44.3 kg/m² with newly diagnosed acromegaly were recruited into the study. All subjects underwent full polysomnography (Embla N7000, Natus, USA and Remlogica software (USA. Results: Sleep disordered breathing was found in 28 (73.7% patients. OSA was revealed in all cases, in 11 (39.3% subjects it was mixed. In 10 (35.7% patients OSA was mild, in 8 (28.6% moderate, and in 10 (35.7% severe. BMI (р<0.01, disease duration (р=0.003, and insulin-like growth factor-1 (IGF-1 level (р=0.04 were different in patients without OSA and patients with moderate-to-severe OSA. No difference was found in sex (р=0.4, age (р=0.064, and growth hormone level (р=0.6. Frequency of arterial hypertension, diabetes mellitus, and other glucose metabolism impairments was the same in subjects without OSA and with severe-to-moderate OSA. Conclusion: All patients with newly diagnosed acromegaly should undergo polysomnography. BMI, disease duration, and IGF-1 level are significant risk factors for OSA development. Correlation OSA with arterial hypertension and glucose metabolism impairments needs to be further investigated.

Simulating Poverty and Inequality Dynamics in Developing Countries

Science.gov (United States)

Ansoms, An; Geenen, Sara

2012-01-01

This article considers how the simulation game of DEVELOPMENT MONOPOLY provides insight into poverty and inequality dynamics in a development context. It first discusses how the game is rooted in theoretical and conceptual frameworks on poverty and inequality. Subsequently, it reflects on selected playing experiences, with special focus on the…

Long fiber polymer composite property calculation in injection molding simulation

Science.gov (United States)

Jin, Xiaoshi; Wang, Jin; Han, Sejin

2013-05-01

Long fiber filled polymer composite materials have attracted a great attention and usage in recent years. However, the injection and compression molded long fiber composite materials possess complex microstructures that include spatial variations in fiber orientation and length. This paper presents the recent implemented anisotropic rotary diffusion - reduced strain closure (ARD-RSC) model for predicting fiber orientation distribution[1] and a newly developed fiber breakage model[2] for predicting fiber length distribution in injection and compression molding simulation, and Eshelby-Mori-Tanaka model[3,4] with fiber-matrix de-bonding model[5] have been implemented to calculate the long fiber composite property distribution with predicted fiber orientation and fiber length distributions. A validation study on fiber orientation, fiber breakage and mechanical property distributions are given with injection molding process simulation.

Application of a newly developed software program for image quality assessment in cone-beam computed tomography.

Science.gov (United States)

de Oliveira, Marcus Vinicius Linhares; Santos, António Carvalho; Paulo, Graciano; Campos, Paulo Sergio Flores; Santos, Joana

2017-06-01

The purpose of this study was to apply a newly developed free software program, at low cost and with minimal time, to evaluate the quality of dental and maxillofacial cone-beam computed tomography (CBCT) images. A polymethyl methacrylate (PMMA) phantom, CQP-IFBA, was scanned in 3 CBCT units with 7 protocols. A macro program was developed, using the free software ImageJ, to automatically evaluate the image quality parameters. The image quality evaluation was based on 8 parameters: uniformity, the signal-to-noise ratio (SNR), noise, the contrast-to-noise ratio (CNR), spatial resolution, the artifact index, geometric accuracy, and low-contrast resolution. The image uniformity and noise depended on the protocol that was applied. Regarding the CNR, high-density structures were more sensitive to the effect of scanning parameters. There were no significant differences between SNR and CNR in centered and peripheral objects. The geometric accuracy assessment showed that all the distance measurements were lower than the real values. Low-contrast resolution was influenced by the scanning parameters, and the 1-mm rod present in the phantom was not depicted in any of the 3 CBCT units. Smaller voxel sizes presented higher spatial resolution. There were no significant differences among the protocols regarding artifact presence. This software package provided a fast, low-cost, and feasible method for the evaluation of image quality parameters in CBCT.

Application of a newly developed software program for image quality assessment in cone-beam computed tomography

International Nuclear Information System (INIS)

De Oliveira, Marcus Vinicius Linhares; Campos, Paulo Sergio Flores; Paulo, Graciano; Santos, Antonio Carvalho; Santos, Joana

2017-01-01

The purpose of this study was to apply a newly developed free software program, at low cost and with minimal time, to evaluate the quality of dental and maxillofacial cone-beam computed tomography (CBCT) images. A polymethyl methacrylate (PMMA) phantom, CQP-IFBA, was scanned in 3 CBCT units with 7 protocols. A macro program was developed, using the free software ImageJ, to automatically evaluate the image quality parameters. The image quality evaluation was based on 8 parameters: uniformity, the signal-to-noise ratio (SNR), noise, the contrast-to-noise ratio (CNR), spatial resolution, the artifact index, geometric accuracy, and low-contrast resolution. The image uniformity and noise depended on the protocol that was applied. Regarding the CNR, high-density structures were more sensitive to the effect of scanning parameters. There were no significant differences between SNR and CNR in centered and peripheral objects. The geometric accuracy assessment showed that all the distance measurements were lower than the real values. Low-contrast resolution was influenced by the scanning parameters, and the 1-mm rod present in the phantom was not depicted in any of the 3 CBCT units. Smaller voxel sizes presented higher spatial resolution. There were no significant differences among the protocols regarding artifact presence. This software package provided a fast, low-cost, and feasible method for the evaluation of image quality parameters in CBCT

Application of a newly developed software program for image quality assessment in cone-beam computed tomography

Energy Technology Data Exchange (ETDEWEB)

De Oliveira, Marcus Vinicius Linhares; Campos, Paulo Sergio Flores [Federal Institute of Bahia, Salvador (Brazil); Paulo, Graciano; Santos, Antonio Carvalho; Santos, Joana [Coimbra Health School, Polytechnic Institute of Coimbra, Coimbra (Portugal)

2017-06-15

The purpose of this study was to apply a newly developed free software program, at low cost and with minimal time, to evaluate the quality of dental and maxillofacial cone-beam computed tomography (CBCT) images. A polymethyl methacrylate (PMMA) phantom, CQP-IFBA, was scanned in 3 CBCT units with 7 protocols. A macro program was developed, using the free software ImageJ, to automatically evaluate the image quality parameters. The image quality evaluation was based on 8 parameters: uniformity, the signal-to-noise ratio (SNR), noise, the contrast-to-noise ratio (CNR), spatial resolution, the artifact index, geometric accuracy, and low-contrast resolution. The image uniformity and noise depended on the protocol that was applied. Regarding the CNR, high-density structures were more sensitive to the effect of scanning parameters. There were no significant differences between SNR and CNR in centered and peripheral objects. The geometric accuracy assessment showed that all the distance measurements were lower than the real values. Low-contrast resolution was influenced by the scanning parameters, and the 1-mm rod present in the phantom was not depicted in any of the 3 CBCT units. Smaller voxel sizes presented higher spatial resolution. There were no significant differences among the protocols regarding artifact presence. This software package provided a fast, low-cost, and feasible method for the evaluation of image quality parameters in CBCT.

Newly Generated Liquid Waste Processing Alternatives Study, Volume 1

Energy Technology Data Exchange (ETDEWEB)

Landman, William Henry; Bates, Steven Odum; Bonnema, Bruce Edward; Palmer, Stanley Leland; Podgorney, Anna Kristine; Walsh, Stephanie

2002-09-01

This report identifies and evaluates three options for treating newly generated liquid waste at the Idaho Nuclear Technology and Engineering Center of the Idaho National Engineering and Environmental Laboratory. The three options are: (a) treat the waste using processing facilities designed for treating sodium-bearing waste, (b) treat the waste using subcontractor-supplied mobile systems, or (c) treat the waste using a special facility designed and constructed for that purpose. In studying these options, engineers concluded that the best approach is to store the newly generated liquid waste until a sodium-bearing waste treatment facility is available and then to co-process the stored inventory of the newly generated waste with the sodium-bearing waste. After the sodium-bearing waste facility completes its mission, two paths are available. The newly generated liquid waste could be treated using the subcontractor-supplied system or the sodium-bearing waste facility or a portion of it. The final decision depends on the design of the sodium-bearing waste treatment facility, which will be completed in coming years.

Proficiency performance benchmarks for removal of simulated brain tumors using a virtual reality simulator NeuroTouch.

Science.gov (United States)

AlZhrani, Gmaan; Alotaibi, Fahad; Azarnoush, Hamed; Winkler-Schwartz, Alexander; Sabbagh, Abdulrahman; Bajunaid, Khalid; Lajoie, Susanne P; Del Maestro, Rolando F

2015-01-01

Assessment of neurosurgical technical skills involved in the resection of cerebral tumors in operative environments is complex. Educators emphasize the need to develop and use objective and meaningful assessment tools that are reliable and valid for assessing trainees' progress in acquiring surgical skills. The purpose of this study was to develop proficiency performance benchmarks for a newly proposed set of objective measures (metrics) of neurosurgical technical skills performance during simulated brain tumor resection using a new virtual reality simulator (NeuroTouch). Each participant performed the resection of 18 simulated brain tumors of different complexity using the NeuroTouch platform. Surgical performance was computed using Tier 1 and Tier 2 metrics derived from NeuroTouch simulator data consisting of (1) safety metrics, including (a) volume of surrounding simulated normal brain tissue removed, (b) sum of forces utilized, and (c) maximum force applied during tumor resection; (2) quality of operation metric, which involved the percentage of tumor removed; and (3) efficiency metrics, including (a) instrument total tip path lengths and (b) frequency of pedal activation. All studies were conducted in the Neurosurgical Simulation Research Centre, Montreal Neurological Institute and Hospital, McGill University, Montreal, Canada. A total of 33 participants were recruited, including 17 experts (board-certified neurosurgeons) and 16 novices (7 senior and 9 junior neurosurgery residents). The results demonstrated that "expert" neurosurgeons resected less surrounding simulated normal brain tissue and less tumor tissue than residents. These data are consistent with the concept that "experts" focused more on safety of the surgical procedure compared with novices. By analyzing experts' neurosurgical technical skills performance on these different metrics, we were able to establish benchmarks for goal proficiency performance training of neurosurgery residents. This

Efficient Simulation Modeling of an Integrated High-Level-Waste Processing Complex

International Nuclear Information System (INIS)

Gregory, Michael V.; Paul, Pran K.

2000-01-01

An integrated computational tool named the Production Planning Model (ProdMod) has been developed to simulate the operation of the entire high-level-waste complex (HLW) at the Savannah River Site (SRS) over its full life cycle. ProdMod is used to guide SRS management in operating the waste complex in an economically efficient and environmentally sound manner. SRS HLW operations are modeled using coupled algebraic equations. The dynamic nature of plant processes is modeled in the form of a linear construct in which the time dependence is implicit. Batch processes are modeled in discrete event-space, while continuous processes are modeled in time-space. The ProdMod methodology maps between event-space and time-space such that the inherent mathematical discontinuities in batch process simulation are avoided without sacrificing any of the necessary detail in the batch recipe steps. Modeling the processes separately in event- and time-space using linear constructs, and then coupling the two spaces, has accelerated the speed of simulation compared to a typical dynamic simulation. The ProdMod simulator models have been validated against operating data and other computer codes. Case studies have demonstrated the usefulness of the ProdMod simulator in developing strategies that demonstrate significant cost savings in operating the SRS HLW complex and in verifying the feasibility of newly proposed processes

The development of fast simulation program for marine reactor parameters

International Nuclear Information System (INIS)

Chen Zhiyun; Hao Jianli; Chen Wenzhen

2012-01-01

Highlights: ► The simplified physical and mathematical models are proposed for a marine reactor system. ► A program is developed with Simulink module and Matlab file. ► The program developed has the merit of easy input preparation, output processing and fast running. ► The program can be used for the fast simulation of marine reactor parameters on the operating field. - Abstract: The fast simulation program for marine reactor parameters is developed based on the Simulink simulating software according to the characteristics of marine reactor with requirement of maneuverability and acute and fast response. The simplified core physical and thermal model, pressurizer model, steam generator model, control rod model, reactivity model and the corresponding Simulink modules are established. The whole program is developed by coupling all the Simulink modules. Two typical transient processes of marine reactor with fast load increase at low power level and load rejection at high power level are adopted to verify the program. The results are compared with those of Relap5/Mod3.2 with good consistency, and the program runs very fast. It is shown that the program is correct and suitable for the fast and accurate simulation of marine reactor parameters on the operating field, which is significant to the marine reactor safe operation.

Developing, implementing and evaluating a simulation learning ...

African Journals Online (AJOL)

Background: The training of undergraduate midwifery students to identify and manage post-partum haemorrhage, is an essential skill in midwifery. Aim: The aim of this study was to develop, implement and evaluate a simulation learning package (SLP) on post-partum haemorrhage for undergraduate midwifery students ...

A genomic audit of newly-adopted autosomal STRs for forensic identification.

Science.gov (United States)

Phillips, C

2017-07-01

In preparation for the growing use of massively parallel sequencing (MPS) technology to genotype forensic STRs, a comprehensive genomic audit of 73 STRs was made in 2016 [Parson et al., Forensic Sci. Int. Genet. 22, 54-63]. The loci examined included miniSTRs that were not in widespread use, but had been incorporated into MPS kits or were under consideration for this purpose. The current study expands the genomic analysis of autosomal STRs that are not commonly used, to include the full set of developed miniSTRs and an additional 24 STRs, most of which have been recently included in several supplementary forensic multiplex kits for capillary electrophoresis. The genomic audit of these 47 newly-adopted STRs examined the linkage status of new loci on the same chromosome as established forensic STRs; analyzed world-wide population variation of the newly-adopted STRs using published data; assessed their forensic informativeness; and compiled the sequence characteristics, repeat structures and flanking regions of each STR. A further 44 autosomal STRs developed for forensic analyses but not incorporated into commercial kits, are also briefly described. Copyright © 2017 Elsevier B.V. All rights reserved.

Virtual reality myringotomy simulation with real-time deformation: development and validity testing.

Science.gov (United States)

Ho, Andrew K; Alsaffar, Hussain; Doyle, Philip C; Ladak, Hanif M; Agrawal, Sumit K

2012-08-01

Surgical simulation is becoming an increasingly common training tool in residency programs. The first objective was to implement real-time soft-tissue deformation and cutting into a virtual reality myringotomy simulator. The second objective was to test the various implemented incision algorithms to determine which most accurately represents the tympanic membrane during myringotomy. Descriptive and face-validity testing. A deformable tympanic membrane was developed, and three soft-tissue cutting algorithms were successfully implemented into the virtual reality myringotomy simulator. The algorithms included element removal, direction prediction, and Delaunay cutting. The simulator was stable and capable of running in real time on inexpensive hardware. A face-validity study was then carried out using a validated questionnaire given to eight otolaryngologists and four senior otolaryngology residents. Each participant was given an adaptation period on the simulator, was blinded to the algorithm being used, and was presented the three algorithms in a randomized order. A virtual reality myringotomy simulator with real-time soft-tissue deformation and cutting was successfully developed. The simulator was stable, ran in real time on inexpensive hardware, and incorporated haptic feedback and stereoscopic vision. The Delaunay cutting algorithm was found to be the most realistic algorithm representing the incision during myringotomy (P virtual reality myringotomy simulator is being developed and now integrates a real-time deformable tympanic membrane that appears to have face validity. Further development and validation studies are necessary before the simulator can be studied with respect to training efficacy and clinical impact. Copyright © 2012 The American Laryngological, Rhinological, and Otological Society, Inc.

Development of Simulants to Support Mixing Tests for High Level Waste and Low Activity Waste

International Nuclear Information System (INIS)

EIBLING, RUSSELLE.

2004-01-01

The objectives of this study were to develop two different types of simulants to support vendor agitator design studies and mixing studies. The initial simulant development task was to develop rheologically-bounding physical simulants and the final portion was to develop a nominal chemical simulant which is designed to match, as closely as possible, the actual sludge from a tank. The physical simulants to be developed included a lower and upper rheologically bounded: pretreated low activity waste (LAW) physical simulant; LAW melter feed physical simulant; pretreated high level waste (HLW) physical simulant; HLW melter feed physical simulant. The nominal chemical simulant, hereafter referred to as the HLW Precipitated Hydroxide simulant, is designed to represent the chemical/physical composition of the actual washed and leached sludge sample. The objective was to produce a simulant which matches not only the chemical composition but also the physical properties of the actual waste sample. The HLW Precipitated Hydroxide simulant could then be used for mixing tests to validate mixing, homogeneity and representative sampling and transferring issues. The HLW Precipitated Hydroxide simulant may also be used for integrated nonradioactive testing of the WTP prior to radioactive operation

Analysis of an industrial process simulator column using third-generation computed tomography

International Nuclear Information System (INIS)

Kirita, Rodrigo; Carvalho, Diego Vergacas de Sousa; Mesquita, Carlos Henrique de; Vasquez, Pablo Antonio S.; Hamada, Margarida Mizue

2011-01-01

The CT methodology must be tested using a simulator column in the laboratory before applying it in the industrial plants. In this work, using the third-generation industrial computed tomography developed at the IPEN, a gas absorption column, used as a simulator column for industrial process was evaluated. It is a glass cylindrical tube of 90 mm diameter and 1400 mm height constituted the following parts: random packed column, liquid circuit (water), gas circuit and analysis was used as a simulator column. Gamma ray tomography experiments were carried out, using this simulator column empty and filled with water. In this work the scanner was setting for 90 views and 19 projections for each detector totalizing 11970 projections. The resulting images describe the presence of liquid or gas phases and are possible to evaluate the linear attenuation coefficients inside the column. In this case, linear attenuation coefficient for water was 0.0813 cm-1. It was established that the newly developed third-generation fan-beam arrangement gamma scanner unit has a good spatial resolution acceptable given the size of the column used in this study. (author)

Development of a flight simulator for the control of plasma discharges

Energy Technology Data Exchange (ETDEWEB)

Ravenel, N.; Artaud, J.F.; Bremond, S.; Guillerminet, B.; Huynh, P.; Moreau, P.; Signoret, J. [CEA Cadarache, IRFM, 13 - Saint-Paul-lez-Durance (France)

2009-07-01

Over the years, feedback controls in fusion experiments become more and more crucial both for increasing performance, stability and ensuring machine protection. Advanced controls, such as current profile control, have to deal with nonlinear, complex physical processes that can hardly be addressed by 'trial and error' methods. Such issues highlight the necessity to build new tools based on plasma discharge flight simulator for the development, test and qualification of advanced control algorithms. A project aiming at developing such tools has started last year at Cea. A part of the project consists in the development of a flight simulator that will be integrated to the present Real Time Control and Acquisition System. Under the experimental program, it will facilitate the development and the implementation of new advanced controllers in the control units. The flight simulator will be based on the European Integrated Tokamak Modelling (ITM) simulation platform. Thus, it will benefit from the development made by the task force and it will be able to offer a development platform for the new controllers of present day European tokamaks and future machine. This paper will address the architecture of the project focussing on the following items: -) Development of a 'high level' interface to build plasma scenarios as a set in sequence; -) Interface of the Tore Supra data and parameters within the ITM data structure; -) Integration of the developments under the ITM simulation platform (Kepler) using Xcos software (produced by the Scilab Consortium) functionalities such as the automatic code generation for the implementation of the controllers; -) Modification of the present control unit software towards modular units in order to facilitate control algorithm development. This document is composed of an abstract followed by the presentation transparencies. (authors)

Development of a subjective refraction simulator

Science.gov (United States)

Perches, S.; Ares, J.; Collados, M. V.

2013-11-01

We have developed simulation software by Matlab (MathworksInc.) with a graphical interface designed for non-expert users. This simulator allows you to complete the process of subjective refraction starting from the aberrometry of the patients and analyse the influence of different factors during the exam. In addition to explain the graphical interface and its working, we show two examples about a complete process of subjective refraction with the influence of high order aberrations and without them showing the retinal image obtained in each step of the refraction process. When the Jackson Cross-Cylinder technique is made with this software, it becomes clear the difficulty of chosen between two images when high order aberrations are present. Therefore, the variability of response during the refraction can be a problem when the examiner has to reach an adequate optical prescription.

Observation of the bone mineral density of newly formed bone using rabbits. Compared with newly formed bone around implants and cortical bone

International Nuclear Information System (INIS)

Nakada, Hiroshi; Numata, Yasuko; Sakae, Toshiro; Tamaki, Hiroyuki; Kato, Takao

2009-01-01

There have been many studies reporting that newly formed bone around implants is spongy bone. However, although the morphology is reported as being like spongy bone, it is difficult to discriminate whether the bone quality of newly formed bone appears similar to osteoid or cortical bone; therefore, evaluation of bone quality is required. The aims of this study were to measure the bone mineral density (BMD) values of newly formed bone around implants after 4, 8, 16, 24 and 48 weeks, to represent these values on three-dimensional color mapping (3Dmap), and to evaluate the change in bone quality associated with newly formed bone around implants. The animal experimental protocol of this study was approved by the Ethics Committee for Animal Experiments of our University. This experiment used 20 surface treatment implants (Ti-6Al-4V alloy: 3.1 mm in diameter and 30.0 mm in length) by grit-blasting. They were embedded into surgically created flaws in femurs of 20 New Zealand white rabbits (16 weeks old, male). The rabbits were sacrificed with an ear intravenous overdose of pentobarbital sodium under general anesthesia each period, and the femurs were resected. We measured BMD of newly formed bone around implants and cortical bone using Micro-CT, and the BMD distribution map of 3Dmap (TRI/3D Bon BMD, Ratoc System Engineering). The BMD of cortical bone was 1,026.3±44.3 mg/cm 3 at 4 weeks, 1,023.8±40.9 mg/cm 3 at 8 weeks, 1,048.2±45.6 mg/cm 3 at 16 weeks, 1,067.2±60.2 mg/cm 3 at 24 weeks, and 1,069.3±50.7 mg/cm 3 at 48 weeks after implantation, showing a non-significant increase each period. The BMD of newly formed bone around implants was 296.8±25.6 mg/cm 3 at 4 weeks, 525.0±72.4 mg/cm 3 at 8 weeks, 691.2±26.0 mg/cm 3 at 16 weeks, 776.9±27.7 mg/cm 3 at 24 weeks, and 845.2±23.1 mg/cm 3 at 48 weeks after implantation, showing a significant increase after each period. It was revealed that the color scale of newly formed bone was Low level at 4 weeks, and then it

Traffic management simulation development.

Science.gov (United States)

2011-01-03

Microscopic simulation can provide significant support to traffic management center (TMC) operations. However, traffic simulation applications require data that are expensive and time-consuming to collect. Data collected by TMCs can be used as a prim...

The SIMRAND methodology - Simulation of Research and Development Projects

Science.gov (United States)

Miles, R. F., Jr.

1984-01-01

In research and development projects, a commonly occurring management decision is concerned with the optimum allocation of resources to achieve the project goals. Because of resource constraints, management has to make a decision regarding the set of proposed systems or tasks which should be undertaken. SIMRAND (Simulation of Research and Development Projects) is a methodology which was developed for aiding management in this decision. Attention is given to a problem description, aspects of model formulation, the reduction phase of the model solution, the simulation phase, and the evaluation phase. The implementation of the considered approach is illustrated with the aid of an example which involves a simplified network of the type used to determine the price of silicon solar cells.

Numerical simulation in steam injection process by a mechanistic approach

Energy Technology Data Exchange (ETDEWEB)

De Souza, J.C.Jr.; Campos, W.; Lopes, D.; Moura, L.S.S. [Petrobras, Rio de Janeiro (Brazil)

2008-10-15

Steam injection is a common thermal recovery method used in very viscous oil reservoirs. The method involves the injection of heat to reduce viscosity and mobilize oil. A steam generation and injection system consists primarily of a steam source, distribution lines, injection wells and a discarding tank. In order to optimize injection and improve the oil recovery factor, one must determine the parameters of steam flow such as pressure, temperature and steam quality. This study focused on developing a unified mathematical model by means of a mechanistic approach for two-phase steam flow in pipelines and wells. The hydrodynamic and heat transfer mechanistic model was implemented in a computer simulator to model the parameters of steam injection while trying to avoid the use of empirical correlations. A marching algorithm was used to determine the distribution of pressure and temperature along the pipelines and wellbores. The mathematical model for steam flow in injection systems, developed by a mechanistic approach (VapMec) performed well when the simulated values of pressures and temperatures were compared with the values measured during field tests. The newly developed VapMec model was incorporated in the LinVap-3 simulator that constitutes an engineering supporting tool for steam injection wells operated by Petrobras. 23 refs., 7 tabs., 6 figs.

Valve-specific, analytic-phenomenological modelling of spray dispersion in zero-dimensional simulation; Ventilspezifische, analytisch-phaenomenologische Modellierung der Sprayausbreitung fuer die nulldimensionale Simulation

Energy Technology Data Exchange (ETDEWEB)

Schuerg, F.; Arndt, S. [Robert Bosch GmbH, Stuttgart (Germany); Weigand, B. [Stuttgart Univ. (Germany). Inst. fuer Thermodynamik der Luft- und Raumfahrt

2007-07-01

Spray-guided combustion processes for gasoline direct injection offer a great fuel saving potential. The quality of mixture formation has direct impact on combustion and emissions and ultimately on the technical feasibility of the consumption advantage. Therefore, it is very important to select the optimal mixture formation strategy. A systematic optimization of the mixture formation process based on experiments or three-dimensional computational fluid dynamics requires tremendous effort. An efficient alternative is the application-oriented, zero-dimensional numerical simulation of mixture formation. With a systemic model formulation in terms of global thermodynamic and fluid mechanical balance equations, the presented simulation model considers all relevant aspects of the mixture formation process. A comparison with measurements in a pressure/temperature chamber using laser-induced exciplex fluorescence tomography revealed a very satisfactory agreement between simulation and experiment. The newly developed, analytic-phenomenological spray propagation model precisely captures the injector-specific mixture formation characteristics of an annular-orifice injector in terms of penetration and volume. Vaporization rate and mean air/fuel ratio as the key quantities of mixture formation are correctly reproduced. Thus, the simulation model is suited to numerically assess the quality and to optimize the strategy of mixture formation. (orig.)

Scientific codes developed and used at GRS. Nuclear simulation chain

Energy Technology Data Exchange (ETDEWEB)

Schaffrath, Andreas; Sonnenkalb, Martin; Sievers, Juergen; Luther, Wolfgang; Velkov, Kiril [Gesellschaft fuer Anlagen und Reaktorsicherheit (GRS) gGmbH, Garching/Muenchen (Germany). Forschungszentrum

2016-05-15

Over 60 technical experts of the reactor safety research division of the Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) gGmbH are developing and validating reliable methods and computer codes - summarized under the term nuclear simulation chain - for the safety-related assessment for all types of nuclear power plants (NPP) and other nuclear facilities considering the current state of science and technology. This nuclear simulation chain has to be able to simulate and assess all relevant physical processes and phenomena for all operating states and (severe) accidents. In the present contribution, the nuclear simulation chain developed and applied by GRS as well as selected examples of its application are presented. The latter demonstrate impressively the width of its scope and its performance. The GRS codes can be passed on request to other (national as well as international) organizations. This contributes to a worldwide increase of the nuclear safety standards. The code transfer is especially important for developing and emerging countries lacking the financial means and/or the necessary know-how for this purpose. At the end of this contribution, the respective course of action is described.

Newly developed central diabetes insipidus following kidney transplantation: a case report.

Science.gov (United States)

Kim, K M; Kim, S M; Lee, J; Lee, S Y; Kwon, S K; Kim, H-Y

2013-09-01

Polyuria after kidney transplantation is a common, usually self-limiting disorder. However, persistent polyuria can cause not only patient discomfort, including polyuria and polydipsia, but also volume depletion that can produce allograft dysfunction. Herein, we have report a case of central diabetes insipidus newly diagnosed after kidney transplantation. A 45-year-old woman with end-stage kidney disease underwent deceased donor kidney transplantation. Two months after the transplantation, she was admitted for persistent polyuria, polydipsia, and nocturia with urine output of more than 4 L/d. Urine osmolarity was 100 mOsm/kg, which implied that the polyuria was due to water rather than solute diuresis. A water deprivation test was compatible with central diabetes insipidus; desmopressin treatment resulted in immediate symptomatic relief. Brain magnetic resonance imaging (MRI) demonstrated diffuse thickening of the pituitary stalk, which was considered to be nonspecific finding. MRI 12 months later showed no change in the pituitary stalk, although the patient has been in good health without polyuria or polydipsia on desmopressin treatment. The possibility of central diabetes insipidus should be considered in patients presenting with persistent polyuria after kidney transplantation. Copyright © 2013 Elsevier Inc. All rights reserved.

Newly graduated nurses' use of knowledge sources: a meta-ethnography.

Science.gov (United States)

Voldbjerg, Siri Lygum; Grønkjaer, Mette; Sørensen, Erik Elgaard; Hall, Elisabeth O C

2016-08-01

To advance evidence on newly graduated nurses' use of knowledge sources. Clinical decisions need to be evidence-based and understanding the knowledge sources that newly graduated nurses use will inform both education and practice. Qualitative studies on newly graduated nurses' use of knowledge sources are increasing though generated from scattered healthcare contexts. Therefore, a metasynthesis of qualitative research on what knowledge sources new graduates use in decision-making was conducted. Meta-ethnography. Nineteen reports, representing 17 studies, published from 2000-2014 were identified from iterative searches in relevant databases from May 2013-May 2014. Included reports were appraised for quality and Noblit and Hare's meta-ethnography guided the interpretation and synthesis of data. Newly graduated nurses' use of knowledge sources during their first 2-year postgraduation were interpreted in the main theme 'self and others as knowledge sources,' with two subthemes 'doing and following' and 'knowing and doing,' each with several elucidating categories. The metasynthesis revealed a line of argument among the report findings underscoring progression in knowledge use and perception of competence and confidence among newly graduated nurses. The transition phase, feeling of confidence and ability to use critical thinking and reflection, has a great impact on knowledge sources incorporated in clinical decisions. The synthesis accentuates that for use of newly graduated nurses' qualifications and skills in evidence-based practice, clinical practice needs to provide a supportive environment which nurtures critical thinking and questions and articulates use of multiple knowledge sources. © 2016 John Wiley & Sons Ltd.

Simulation in Occupational Therapy Curricula: A literature review.

Science.gov (United States)

Bennett, Sally; Rodger, Sylvia; Fitzgerald, Cate; Gibson, Libby

2017-08-01

Simulated learning experiences are increasingly being used in health-care education to enhance student engagement and provide experiences that reflect clinical practice; however, simulation has not been widely investigated in occupational therapy curricula. The aim of this paper was to: (i) describe the existing research about the use and evaluation of simulation over the last three decades in occupational therapy curricula and (ii) consider how simulation has been used to develop competence in students. A literature review was undertaken with searches of MEDLINE, CINAHL and ERIC to locate articles that described or evaluated the use of simulation in occupational therapy curricula. Fifty-seven papers were identified. Occupational therapy educators have used the full scope of simulation modalities, including written case studies (22), standardised patients (13), video case studies (15), computer-based and virtual reality cases (7), role-play (8) and mannequins and part-task trainers (4). Ten studies used combinations of these modalities and two papers compared modalities. Most papers described the use of simulation for foundational courses, as for preparation for fieldwork, and to address competencies necessary for newly graduating therapists. The majority of studies were descriptive, used pre-post design, or were student's perceptions of the value of simulation. Simulation-based education has been used for a wide range of purposes in occupational therapy curricula and appears to be well received. Randomised controlled trials are needed to more accurately understand the effects of simulation not just for occupational therapy students but for longer term outcomes in clinical practice. © 2017 Occupational Therapy Australia.

Toward Developing Authentic Leadership: Team-Based Simulations

Science.gov (United States)

Shapira-Lishchinsky, Orly

2014-01-01

Although there is a consensus that authentic leadership should be an essential component in educational leadership, no study to date has ever tried to find whether team-based simulations may promote authentic leadership. The purpose of this study was to identify whether principal trainees can develop authentic leadership through ethical decision…

The nanotoxicology of a newly developed zero-valent iron nanomaterial for groundwater remediation and its remediation efficiency assessment combined with in vitro bioassays for detection of dioxin-like environmental pollutants

OpenAIRE

Schiwy, Andreas Herbert

2016-01-01

The assessment of chemicals and new compounds is an important task of ecotoxicology. In this thesis a newly developed zero-valent iron material for nanoremediation of groundwater contaminations was investigated and in vitro bioassays for high throughput screening were developed. These two elements of the thesis were combined to assess the remediation efficiency of the nanomaterial on the groundwater contaminant acridine. The developed in vitro bioassays were evaluated for quantification of th...

Development of Research Reactor Simulator and Its Application to Dynamic Test-bed

International Nuclear Information System (INIS)

Kwon, Kee Choon; Park, Jae Chang; Lee, Seung Wook; Bang, Dane; Bae, Sung Won

2014-01-01

We developed HANARO and the Jordan Research and Training Reactor (JRTR) real-time simulator for operating staff training. The main purpose of this simulator is operator training, but we modified this simulator as a dynamic test-bed to test the reactor regulating system in HANARO or JRTR before installation. The simulator configuration is divided into hardware and software. The simulator hardware consists of a host computer, 6 operator stations, a network switch, and a large display panel. The simulator software is divided into three major parts: a mathematical modeling module, which executes the plant dynamic modeling program in real-time, an instructor station module that manages user instructions, and a human machine interface (HMI) module. The developed research reactors are installed in the Korea Atomic Energy Research Institute nuclear training center for reactor operator training. To use the simulator as a dynamic test-bed, the reactor regulating system modeling software of the simulator was replaced by a hardware controller and the simulator and target controller were interfaced with a hard-wired and network-based interface

Development of Research Reactor Simulator and Its Application to Dynamic Test-bed

Energy Technology Data Exchange (ETDEWEB)

Kwon, Kee Choon; Park, Jae Chang; Lee, Seung Wook; Bang, Dane; Bae, Sung Won [KAERI, Daejeon (Korea, Republic of)

2014-08-15

We developed HANARO and the Jordan Research and Training Reactor (JRTR) real-time simulator for operating staff training. The main purpose of this simulator is operator training, but we modified this simulator as a dynamic test-bed to test the reactor regulating system in HANARO or JRTR before installation. The simulator configuration is divided into hardware and software. The simulator hardware consists of a host computer, 6 operator stations, a network switch, and a large display panel. The simulator software is divided into three major parts: a mathematical modeling module, which executes the plant dynamic modeling program in real-time, an instructor station module that manages user instructions, and a human machine interface (HMI) module. The developed research reactors are installed in the Korea Atomic Energy Research Institute nuclear training center for reactor operator training. To use the simulator as a dynamic test-bed, the reactor regulating system modeling software of the simulator was replaced by a hardware controller and the simulator and target controller were interfaced with a hard-wired and network-based interface.

Certification document for newly generated contact-handled transuranic waste

International Nuclear Information System (INIS)

Box, W.D.; Setaro, J.

1984-01-01

The US Department of Energy has requested that all national laboratories handling defense waste develop and augment a program whereby all newly generated contact-handled transuranic (TRU) waste be contained, stored, and then shipped to the Waste Isolation Pilot Plant (WIPP) in accordance with the requirements set forth in WIPP-DOE-114. The program described in this report delineates how Oak Ridge National Laboratory intends to comply with these requirements and lists the procedures used by each generator to ensure that their TRU wastes are certifiable for shipment to WIPP

A Mirror for Managers: Using Simulation to Develop Management Teams. Technical Report 23.

Science.gov (United States)

Kaplan, Robert E.; And Others

Although simulation is among the least common of the many methods consultants employ to stimulate team development, realistic simulation can help in the diagnosis of management teams. Simulations fill a gap in the repertoire of data collection methods for organizational diagnosis and development by affording an opportunity for direct observation…

Newly blind persons using virtual environment system in a traditional orientation and mobility rehabilitation program: a case study.

Science.gov (United States)

Lahav, Orly; Schloerb, David W; Srinivasan, Mandayam A

2012-09-01

This paper presents a virtual reality system (the BlindAid) developed for orientation and mobility training of people who are newly blind. The BlindAid allows users to interact with different virtual structures and objects via auditory and haptic feedback. This case study aims to examine if and how the BlindAid, in conjunction with a traditional rehabilitation programme, can help people who are newly blind develop new orientation and mobility methods. Follow-up research based on this study, with a large experiment and control group, could contribute to the area of orientation and mobility rehabilitation training for the newly blind. The case study research focused on A., a woman who is newly blind, for 17 virtual sessions spanning ten weeks, during the 12 weeks of her traditional orientation and mobility rehabilitation programme. The research was implemented by using virtual environment (VE) exploration and orientation tasks in VE and physical spaces. The research methodology used both qualitative and quantitative methods, including interviews, questionnaire, videotape recording, and user computer logs. The results of this study helped elucidate several issues concerning the contribution of the BlindAid system to the exploration strategies and learning processes experienced by the participant in her encounters with familiar and unfamiliar physical surroundings. [Box: see text].

DEVELOPMENT OF AN INSOLUBLE SALT SIMULANT TO SUPPORT ENHANCED CHEMICAL CLEANING TESTS

International Nuclear Information System (INIS)

Eibling, R

2008-01-01

The closure process for high level waste tanks at the Savannah River Site will require dissolution of the crystallized salts that are currently stored in many of the tanks. The insoluble residue from salt dissolution is planned to be removed by an Enhanced Chemical Cleaning (ECC) process. Development of a chemical cleaning process requires an insoluble salt simulant to support evaluation tests of different cleaning methods. The Process Science and Engineering section of SRNL has been asked to develop an insoluble salt simulant for use in testing potential ECC processes (HLE-TTR-2007-017). An insoluble salt simulant has been developed based upon the residues from salt dissolution of saltcake core samples from Tank 28F. The simulant was developed for use in testing SRS waste tank chemical cleaning methods. Based on the results of the simulant development process, the following observations were developed: (1) A composition based on the presence of 10.35 grams oxalate and 4.68 grams carbonate per 100 grams solids produces a sufficiently insoluble solids simulant. (2) Aluminum observed in the solids remaining from actual waste salt dissolution tests is probably precipitated from sodium aluminate due to the low hydroxide content of the saltcake. (3) In-situ generation of aluminum hydroxide (by use of aluminate as the Al source) appears to trap additional salts in the simulant in a manner similar to that expected for actual waste samples. (4) Alternative compositions are possible with higher oxalate levels and lower carbonate levels. (5) The maximum oxalate level is limited by the required Na content of the insoluble solids. (6) Periodic mixing may help to limit crystal growth in this type of salt simulant. (7) Long term storage of an insoluble salt simulant is likely to produce a material that can not be easily removed from the storage container. Production of a relatively fresh simulant is best if pumping the simulant is necessary for testing purposes. The insoluble

The impact of organisational culture on the adaptation of newly ...

African Journals Online (AJOL)

Usually newly employed nurses find adjusting to a work setting a challenging experience. Their successful adaptation to their work situation is greatly influenced by the socialisation process inherent in the organisational culture. The newly employed nurse often finds that the norms are unclear, confusing and restrictive.

Cultures of simulations vs. cultures of calculations? The development of simulation practices in meteorology and astrophysics

Science.gov (United States)

Sundberg, Mikaela

While the distinction between theory and experiment is often used to discuss the place of simulation from a philosophical viewpoint, other distinctions are possible from a sociological perspective. Turkle (1995) distinguishes between cultures of calculation and cultures of simulation and relates these cultures to the distinction between modernity and postmodernity, respectively. What can we understand about contemporary simulation practices in science by looking at them from the point of view of these two computer cultures? What new questions does such an analysis raise for further studies? On the basis of two case studies, the present paper compares and discusses simulation activities in astrophysics and meteorology. It argues that simulation practices manifest aspects of both of these cultures simultaneously, but in different situations. By employing the dichotomies surface/depth, play/seriousness, and extreme/reasonable to characterize and operationalize cultures of calculation and cultures of simulation as sensitizing concepts, the analysis shows how simulation code work shifts from development to use, the importance of but also resistance towards too much visualizations, and how simulation modelers play with extreme values, yet also try to achieve reasonable results compared to observations.

Normal Brain-Skull Development with Hybrid Deformable VR Models Simulation.

Science.gov (United States)

Jin, Jing; De Ribaupierre, Sandrine; Eagleson, Roy

2016-01-01

This paper describes a simulation framework for a clinical application involving skull-brain co-development in infants, leading to a platform for craniosynostosis modeling. Craniosynostosis occurs when one or more sutures are fused early in life, resulting in an abnormal skull shape. Surgery is required to reopen the suture and reduce intracranial pressure, but is difficult without any predictive model to assist surgical planning. We aim to study normal brain-skull growth by computer simulation, which requires a head model and appropriate mathematical methods for brain and skull growth respectively. On the basis of our previous model, we further specified suture model into fibrous and cartilaginous sutures and develop algorithm for skull extension. We evaluate the resulting simulation by comparison with datasets of cases and normal growth.

Protein adsorption on nanoparticles: model development using computer simulation

International Nuclear Information System (INIS)

Shao, Qing; Hall, Carol K

2016-01-01

The adsorption of proteins on nanoparticles results in the formation of the protein corona, the composition of which determines how nanoparticles influence their biological surroundings. We seek to better understand corona formation by developing models that describe protein adsorption on nanoparticles using computer simulation results as data. Using a coarse-grained protein model, discontinuous molecular dynamics simulations are conducted to investigate the adsorption of two small proteins (Trp-cage and WW domain) on a model nanoparticle of diameter 10.0 nm at protein concentrations ranging from 0.5 to 5 mM. The resulting adsorption isotherms are well described by the Langmuir, Freundlich, Temkin and Kiselev models, but not by the Elovich, Fowler–Guggenheim and Hill–de Boer models. We also try to develop a generalized model that can describe protein adsorption equilibrium on nanoparticles of different diameters in terms of dimensionless size parameters. The simulation results for three proteins (Trp-cage, WW domain, and GB3) on four nanoparticles (diameter  =  5.0, 10.0, 15.0, and 20.0 nm) illustrate both the promise and the challenge associated with developing generalized models of protein adsorption on nanoparticles. (paper)

Challenges to the development of complex virtual reality surgical simulations.

Science.gov (United States)

Seymour, N E; Røtnes, J S

2006-11-01

Virtual reality simulation in surgical training has become more widely used and intensely investigated in an effort to develop safer, more efficient, measurable training processes. The development of virtual reality simulation of surgical procedures has begun, but well-described technical obstacles must be overcome to permit varied training in a clinically realistic computer-generated environment. These challenges include development of realistic surgical interfaces and physical objects within the computer-generated environment, modeling of realistic interactions between objects, rendering of the surgical field, and development of signal processing for complex events associated with surgery. Of these, the realistic modeling of tissue objects that are fully responsive to surgical manipulations is the most challenging. Threats to early success include relatively limited resources for development and procurement, as well as smaller potential for return on investment than in other simulation industries that face similar problems. Despite these difficulties, steady progress continues to be made in these areas. If executed properly, virtual reality offers inherent advantages over other training systems in creating a realistic surgical environment and facilitating measurement of surgeon performance. Once developed, complex new virtual reality training devices must be validated for their usefulness in formative training and assessment of skill to be established.

Encounters of Newly Qualified Teachers with Micro-Politics in Primary Schools in Zimbabwe

Science.gov (United States)

Magudu, Snodia; Gumbo, Mishack

2017-01-01

This article demonstrates, through the example of Zimbabwe, the complexities of micro-political learning during induction. It reports on the experiences of ten newly qualified teachers with micro-politics or power relations in their schools during induction and locates these experiences within the broader context of their professional development.…

Development of the McGill simulator for endoscopic sinus surgery: a new high-fidelity virtual reality simulator for endoscopic sinus surgery.

Science.gov (United States)

Varshney, Rickul; Frenkiel, Saul; Nguyen, Lily H P; Young, Meredith; Del Maestro, Rolando; Zeitouni, Anthony; Tewfik, Marc A

2014-01-01

The technical challenges of endoscopic sinus surgery (ESS) and the high risk of complications support the development of alternative modalities to train residents in these procedures. Virtual reality simulation is becoming a useful tool for training the skills necessary for minimally invasive surgery; however, there are currently no ESS virtual reality simulators available with valid evidence supporting their use in resident education. Our aim was to develop a new rhinology simulator, as well as to define potential performance metrics for trainee assessment. The McGill simulator for endoscopic sinus surgery (MSESS), a new sinus surgery virtual reality simulator with haptic feedback, was developed (a collaboration between the McGill University Department of Otolaryngology-Head and Neck Surgery, the Montreal Neurologic Institute Simulation Lab, and the National Research Council of Canada). A panel of experts in education, performance assessment, rhinology, and skull base surgery convened to identify core technical abilities that would need to be taught by the simulator, as well as performance metrics to be developed and captured. The MSESS allows the user to perform basic sinus surgery skills, such as an ethmoidectomy and sphenoidotomy, through the use of endoscopic tools in a virtual nasal model. The performance metrics were developed by an expert panel and include measurements of safety, quality, and efficiency of the procedure. The MSESS incorporates novel technological advancements to create a realistic platform for trainees. To our knowledge, this is the first simulator to combine novel tools such as the endonasal wash and elaborate anatomic deformity with advanced performance metrics for ESS.

Methodology for Developing a Diesel Exhaust After Treatment Simulation Tool

DEFF Research Database (Denmark)

Christiansen, Tine; Jensen, Johanne; Åberg, Andreas

2018-01-01

A methodology for the development of catalyst models is presented. Also, a methodology of the implementation of such models into a modular simulation tool, which simulates the units in succession, is presented. A case study is presented illustrating how suitable models can be found and used for s...

Application of image simulation in weapon system development

CSIR Research Space (South Africa)

Willers, CJ

2007-09-01

Full Text Available systems. Index Terms—image simulation, scene modelling, weapon eval- uation, infrared I. INTRODUCTION Simulation is used increasingly to support military system development throughout all the product life cycle phases, from concept analysis... the theoretical models. The signature 0 2 4 6 8 10 12 14 0 0.1 0.2 0.3 0.4 0.5 Wavelength [ m]� Tr a n sm itt an ce Path length = 10 000 m Sub-arctic Summer: 14 C ambient, 75% RH, Navy maritime aerosol, 23 km visibility Very high humidity: 35 C...

The construction of social identity in newly recruited nuclear engineering staff: A longitudinal study

International Nuclear Information System (INIS)

Nguyen, Lynda; Murphy, Glen; Chang, Artemis

2014-01-01

This study examines the process by which newly recruited nuclear engineering and technical staff came to understand, define, think, feel and behave within a distinct group that has a direct contribution to the organization's overall emphasis on a culture of reliability and system safety. In the field of organizational behavior the interactive model of social identity formation has been recently proposed to explain the process by which the internalization of shared norms and values occurs, an element critical in identity formation. Using this rich model of organizational behavior we analyzed multiple sources of data from nine new hires over a period of three years. This was done from the time they were employed to investigate the construction of social identity by new entrants entering into a complex organizational setting reflected in the context of a nuclear facility. Informed by our data analyses, we found support for the interactive model of social identity development and report the unexpected finding that a newly appointed member's age and level of experience appears to influence the manner in which they adapt, and assimilate into their surroundings. This study represents an important contribution to the safety and reliability literature as it provides a rich insight into the way newly recruited employees enact the process by which their identities are formed and hence act, particularly under conditions of duress or significant organizational disruption in complex organizational settings. - Highlights: • We examined how newly recruited nuclear engineer staff develop their social identity. • The study empirically examined the interactive model of social identity formation. • Innovative research strategies were used to capture rich primary data for all case studies. • Age and experience moderated internalization route and the social identity formation process

Developments in the electron gun simulation program, EGUN

International Nuclear Information System (INIS)

Herrmannsfeldt, W.B.

1994-11-01

This paper discusses the developments in the electron gun simulation programs that are based on EGUN with its derivatives and supporting programs. Much of the code development has been inspired by technology changes in computer hardware; the implications of this evolution on EGN2 are discussed. Some examples and a review of the capabilities of the EGUN family are described

Developments in the electron gun simulation program, EGUN

Science.gov (United States)

Herrmannsfeldt, W. B.

1995-07-01

This paper discusses the developments in the electron gun simulation programs that are based on EGUN with its derivatives and supporting programs. Much of the code development has been inspired by technology changes in computer hardware; the implications of this evolution on EGN2 are discussed. Some examples and a review of the capabilities of the EGUN family are described.

Dynamic simulation for effective workforce management in new product development

Directory of Open Access Journals (Sweden)

M. Mutingi

2012-10-01

Full Text Available Effective planning and management of workforce for new product development (NPD projects is a great challenge to many organisations, especially in the presence of engineering changes during the product development process. The management objective in effective workforce management is to recruit, develop and deploy the right people at the right place at the right time so as to fulfill organizational objectives. In this paper, we propose a dynamic simulation model to address the workforce management problem in a typical NPD project consisting of design, prototyping, and production phases. We assume that workforce demand is a function of project work remaining and the current available skill pool. System dynamics simulation concepts are used to capture the causality relationships and feedback loops in the workforce system from a systems thinking. The evaluation of system dynamics simulation reveals the dynamic behaviour in NPD workforce management systems and shows how adaptive dynamic recruitment and training decisions can effectively balance the workforce system during the NPD process.

Assessment for markers of nephropathy in newly diagnosed type 2 ...

African Journals Online (AJOL)

Objective: To assess for markers of nephropathy in newly diagnosed type 2 diabetics, using blood pressure levels, endogenous creatinine clearance and urinary protein excretion as markers of renal disease. Study design: Ninety newly diagnosed type 2 diabetics were studied within 6 weeks of diagnosis. They were in ...

AUTOMATIC GENERATION OF ROAD INFRASTRUCTURE IN 3D FOR VEHICLE SIMULATORS

Directory of Open Access Journals (Sweden)

Adam Orlický

2017-12-01

Full Text Available One of the modern methods of testing new systems and interfaces in vehicles is testing in a vehicle simulator. Providing quality models of virtual scenes is one of tasks for driver-car interaction interface simulation. Nowadays, there exist many programs for creating 3D models of road infrastructures, but most of these programs are very expensive or canÂtt export models for the following use. Therefore, a plug-in has been developed at the Faculty of Transportation Sciences in Prague. It can generate road infrastructure by Czech standard for designing roads (CSN 73 6101. The uniqueness of this plug-in is that it is the first tool for generating road infrastructure in NURBS representation. This type of representation brings more exact models and allows to optimize transfer for creating quality models for vehicle simulators. The scenes created by this plug-in were tested on vehicle simulators. The results have shown that with newly created scenes drivers had a much better feeling in comparison to previous scenes.

An Open Source-based Approach to the Development of Research Reactor Simulator

International Nuclear Information System (INIS)

Joo, Sung Moon; Suh, Yong Suk; Park, Cheol Park

2016-01-01

In reactor design, operator training, safety analysis, or research using a reactor, it is essential to simulate time dependent reactor behaviors such as neutron population, fluid flow, and heat transfer. Furthermore, in order to use the simulator to train and educate operators, a mockup of the reactor user interface is required. There are commercial software tools available for reactor simulator development. However, it is costly to use those commercial software tools. Especially for research reactors, it is difficult to justify the high cost as regulations on research reactor simulators are not as strict as those for commercial Nuclear Power Plants(NPPs). An open source-based simulator for a research reactor is configured as a distributed control system based on EPICS framework. To demonstrate the use of the simulation framework proposed in this work, we consider a toy example. This example approximates a 1-second impulse reactivity insertion in a reactor, which represents the instantaneous removal and reinsertion of a control rod. The change in reactivity results in a slightly delayed change in power and corresponding increases in temperatures throughout the system. We proposed an approach for developing research reactor simulator using open source software tools, and showed preliminary results. The results demonstrate that the approach presented in this work can provide economical and viable way of developing research reactor simulators

Efficacy of Intra-articular Injection of a Newly Developed Plasma Rich in Growth Factor (PRGF) Versus Hyaluronic Acid on Pain and Function of Patients with Knee Osteoarthritis: A Single-Blinded Randomized Clinical Trial

Science.gov (United States)

Raeissadat, Seyed Ahmad; Rayegani, Seyed Mansoor; Ahangar, Azadeh Gharooee; Abadi, Porya Hassan; Mojgani, Parviz; Ahangar, Omid Gharooi

2017-01-01

Background and objectives: Knee osteoarthritis is the most common joint disease. We aimed to compare the efficacy and safety of intra-articular injection of a newly developed plasma rich in growth factor (PRGF) versus hyaluronic acid (HA) on pain and function of patients with knee osteoarthritis. Methods: In this single-blinded randomized clinical trial, patients with symptomatic osteoarthritis of knee were assigned to receive 2 intra-articular injections of our newly developed PRGF in 3 weeks or 3 weekly injections of HA. Our primary outcome was the mean change from baseline until 2 and 6 months post intervention in scores of visual analog scale, Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC), and Lequesne index. We used analysis of variance for repeated-measures statistical test. Results: A total of 69 patients entered final analysis. The mean age of patients was 58.2 ± 7.41 years and 81.2% were women. In particular, total WOMAC index decreased from 42.9 ± 13.51 to 26.8 ± 13.45 and 24.4 ± 16.54 at 2 and 6 months in the newly developed PRGF group (within subjects P = .001), and from 38.8 ± 12.62 to 27.8 ± 11.01 and 27.4 ± 11.38 at 2 and 6 months in the HA group (within subjects P = .001), respectively (between subjects P = .631). There was no significant difference between PRGF and HA groups in patients’ satisfaction and minor complications of injection, whereas patients in HA group reported significantly lower injection-induced pain. Conclusions: In 6 months follow up, our newly developed PRGF and HA, both are effective options to decrease pain and improvement of function in patients with symptomatic mild to moderate knee osteoarthritis. PMID:29051707

Efficacy of Intra-articular Injection of a Newly Developed Plasma Rich in Growth Factor (PRGF Versus Hyaluronic Acid on Pain and Function of Patients with Knee Osteoarthritis: A Single-Blinded Randomized Clinical Trial

Directory of Open Access Journals (Sweden)

Seyed Ahmad Raeissadat

2017-10-01

Full Text Available Background and objectives: Knee osteoarthritis is the most common joint disease. We aimed to compare the efficacy and safety of intra-articular injection of a newly developed plasma rich in growth factor (PRGF versus hyaluronic acid (HA on pain and function of patients with knee osteoarthritis. Methods: In this single-blinded randomized clinical trial, patients with symptomatic osteoarthritis of knee were assigned to receive 2 intra-articular injections of our newly developed PRGF in 3 weeks or 3 weekly injections of HA. Our primary outcome was the mean change from baseline until 2 and 6 months post intervention in scores of visual analog scale, Western Ontario and McMaster Universities Osteoarthritis Index (WOMAC, and Lequesne index. We used analysis of variance for repeated-measures statistical test. Results: A total of 69 patients entered final analysis. The mean age of patients was 58.2 ± 7.41 years and 81.2% were women. In particular, total WOMAC index decreased from 42.9 ± 13.51 to 26.8 ± 13.45 and 24.4 ± 16.54 at 2 and 6 months in the newly developed PRGF group (within subjects P  = .001, and from 38.8 ± 12.62 to 27.8 ± 11.01 and 27.4 ± 11.38 at 2 and 6 months in the HA group (within subjects P  = .001, respectively (between subjects P  = .631. There was no significant difference between PRGF and HA groups in patients’ satisfaction and minor complications of injection, whereas patients in HA group reported significantly lower injection-induced pain. Conclusions: In 6 months follow up, our newly developed PRGF and HA, both are effective options to decrease pain and improvement of function in patients with symptomatic mild to moderate knee osteoarthritis.

Numerical and analytical investigation towards performance enhancement of a newly developed rockfall protective cable-net structure

Directory of Open Access Journals (Sweden)

S. Dhakal

2012-04-01

Full Text Available In a previous companion paper, we presented a three-tier modelling of a particular type of rockfall protective cable-net structure (barrier, developed newly in Japan. Therein, we developed a three-dimensional, Finite Element based, nonlinear numerical model having been calibrated/back-calculated and verified with the element- and structure-level physical tests. Moreover, using a very simple, lumped-mass, single-degree-of-freedom, equivalently linear analytical model, a global-displacement-predictive correlation was devised by modifying the basic equation – obtained by combining the principles of conservation of linear momentum and energy – based on the back-analysis of the tests on the numerical model. In this paper, we use the developed models to explore the performance enhancement potential of the structure in terms of (a the control of global displacement – possibly the major performance criterion for the proposed structure owing to a narrow space available in the targeted site, and (b the increase in energy dissipation by the existing U-bolt-type Friction-brake Devices – which are identified to have performed weakly when integrated into the structure. A set of parametric investigations have revealed correlations to achieve the first objective in terms of the structure's mass, particularly by manipulating the wire-net's characteristics, and has additionally disclosed the effects of the impacting-block's parameters. Towards achieving the second objective, another set of parametric investigations have led to a proposal of a few innovative improvements in the constitutive behaviour (model of the studied brake device (dissipator, in addition to an important recommendation of careful handling of the device based on the identified potential flaw.

Virtual Reality Simulator Developed Welding Technology Skills

Science.gov (United States)

Yunus, Faizal Amin Nur; Baser, Jamil Abd; Masran, Saiful Hadi; Razali, Nizamuddin; Rahim, Bekri

2011-01-01

The purpose of this study was to identify the suitability of VR welding simulator application towards CBT in developing welding skills upon new trainees at the Centre of Instructor and Advanced Skills Training (CIAST) Shah Alam Selangor and National Youth Skills Institute (IKBN) Pagoh Johor. The significance of the study was to create a…

A Report on the Research and Development of Instructional Simulation.

Science.gov (United States)

West, Charles K.; And Others

The purpose of this report is to communicate findings on current knowledge of simulation design, development, and evaluation. Research on this project was guided by questions posed by the Defense Systems Management College in Fort Belvoir, Virginia. These questions fall into three categories: the constituents of good instructional simulations, the…

Characteristics of low polymerization shrinkage flowable resin composites in newly-developed cavity base materials for bulk filling technique.

Science.gov (United States)

Nitta, Keiko; Nomoto, Rie; Tsubota, Yuji; Tsuchikawa, Masuji; Hayakawa, Tohru

2017-11-29

The purpose of this study was to evaluate polymerization shrinkage and other physical properties of newly-developed cavity base materials for bulk filling technique, with the brand name BULK BASE (BBS). Polymerization shrinkage was measured according to ISO/FDIS 17304. BBS showed the significantly lowest polymerization shrinkage and significantly higher depth of cure than conventional flowable resin composites (p<0.05). The Knoop hardness, flexural strength and elastic modulus of that were significantly lower than conventional flowable resin composites (p<0.05). BBS had the significantly greatest filler content (p<0.05). SEM images of the surface showed failure of fillers. The lowest polymerization shrinkage was due to the incorporation of a new type of low shrinkage monomer, which has urethane moieties. There were no clear correlations between inorganic filler contents and polymerization shrinkage, flexural strength and elastic modulus. In conclusion, the low polymerization shrinkage of BBS will be useful for cavity treatment in dental clinics.

14 CFR 26.39 - Newly produced airplanes: Fuel tank flammability.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Newly produced airplanes: Fuel tank... Tank Flammability § 26.39 Newly produced airplanes: Fuel tank flammability. (a) Applicability: This... Series 767 Series (b) Any fuel tank meeting all of the criteria stated in paragraphs (b)(1), (b)(2) and...

Distributed Sensor Network Software Development Testing through Simulation

Energy Technology Data Exchange (ETDEWEB)

Brennan, Sean M. [Univ. of New Mexico, Albuquerque, NM (United States)

2003-12-01

The distributed sensor network (DSN) presents a novel and highly complex computing platform with dif culties and opportunities that are just beginning to be explored. The potential of sensor networks extends from monitoring for threat reduction, to conducting instant and remote inventories, to ecological surveys. Developing and testing for robust and scalable applications is currently practiced almost exclusively in hardware. The Distributed Sensors Simulator (DSS) is an infrastructure that allows the user to debug and test software for DSNs independent of hardware constraints. The exibility of DSS allows developers and researchers to investigate topological, phenomenological, networking, robustness and scaling issues, to explore arbitrary algorithms for distributed sensors, and to defeat those algorithms through simulated failure. The user speci es the topology, the environment, the application, and any number of arbitrary failures; DSS provides the virtual environmental embedding.

Self-Esteem: A Comparison between Hong Kong Children and Newly Arrived Chinese Children

Science.gov (United States)

Chan, Yiu Man; Chan, Christine Mei-Sheung

2004-01-01

The Self-esteem Inventory developed by Coopersmith (1967) was used to measure the self-esteem of 387 Chinese children. The sample included newly arrived mainland Chinese children and Hong Kong children. The results showed significant statistical differences when measuring the self-esteem level associated with the length of their stay in Hong Kong…

RELAP/SCDAPSIM Reactor System Simulator Development and Training for University and Reactor Applications

International Nuclear Information System (INIS)

Hohorst, J.K.; Allison, C.M.

2010-01-01

The RELAP/SCDAPSIM code, designed to predict the behaviour of reactor systems during normal and accident conditions, is being developed as part of an international nuclear technology development program called SDTP (SCDAP Development and Training Program). SDTP involves more than 60 organizations in 28 countries. One of the important applications of the code is for simulator training of university faculty and students, reactor analysts, and reactor operations and technical support staff. Examples of RELAP/SCDAPSIM-based system thermal hydraulic and severe accident simulator packages include the SAFSIM simulator developed by NECSA for the SAFARI research reactor in South Africa, university-developed simulators at the University of Mexico and Shanghai Jiao Tong University in China, and commercial VISA and RELSIM packages used for analyst and reactor operations staff training. This paper will briefly describe the different packages/facilities. (authors)

RELAP/SCDAPSIM Reactor System Simulator Development and Training for University and Reactor Applications

Energy Technology Data Exchange (ETDEWEB)

Hohorst, J.K.; Allison, C.M. [Innovative Systems Software, 1242 South Woodruff Avenue, Idaho Falls, Idaho 83404 (United States)

2010-07-01

The RELAP/SCDAPSIM code, designed to predict the behaviour of reactor systems during normal and accident conditions, is being developed as part of an international nuclear technology development program called SDTP (SCDAP Development and Training Program). SDTP involves more than 60 organizations in 28 countries. One of the important applications of the code is for simulator training of university faculty and students, reactor analysts, and reactor operations and technical support staff. Examples of RELAP/SCDAPSIM-based system thermal hydraulic and severe accident simulator packages include the SAFSIM simulator developed by NECSA for the SAFARI research reactor in South Africa, university-developed simulators at the University of Mexico and Shanghai Jiao Tong University in China, and commercial VISA and RELSIM packages used for analyst and reactor operations staff training. This paper will briefly describe the different packages/facilities. (authors)

Developments in the electron gun simulation program, EGUN

International Nuclear Information System (INIS)

Herrmannsfeldt, W.B.

1995-01-01

This paper discusses the developments in the electron gun simulation programs that are based on EGUN with its derivatives and supporting programs. Much of the code development has been inspired by technology changes in computer hardware; the implications of this evolution on EGN2 are discussed. Some examples and a review of the capabilities of the EGUN family are described. copyright 1995 American Institute of Physics

Hybrid simulation research on formation mechanism of tungsten nanostructure induced by helium plasma irradiation

Energy Technology Data Exchange (ETDEWEB)

Ito, Atsushi M., E-mail: ito.atsushi@nifs.ac.jp [National Institute for Fusion Science, 322-6 Oroshi-cho, Toki 509-5292 (Japan); Takayama, Arimichi; Oda, Yasuhiro [National Institute for Fusion Science, 322-6 Oroshi-cho, Toki 509-5292 (Japan); Tamura, Tomoyuki; Kobayashi, Ryo; Hattori, Tatsunori; Ogata, Shuji [Nagoya Institute of Technology, Gokiso-cho, Showa-ku, Nagoya 466-8555 (Japan); Ohno, Noriyasu; Kajita, Shin [Nagoya University, Furo-cho, Chikusa-ku, Nagoya 464-8603 (Japan); Yajima, Miyuki [National Institute for Fusion Science, 322-6 Oroshi-cho, Toki 509-5292 (Japan); Noiri, Yasuyuki [Nagoya University, Furo-cho, Chikusa-ku, Nagoya 464-8603 (Japan); Yoshimoto, Yoshihide [University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-8656 (Japan); Saito, Seiki [Kushiro National College of Technology, Kushiro, Hokkaido 084-0916 (Japan); Takamura, Shuichi [Aichi Institute of Technology, 1247 Yachigusa, Yakusa-cho, Toyota 470-0392 (Japan); Murashima, Takahiro [Tohoku University, 6-3, Aramaki-Aza-Aoba, Aoba-Ward, Sendai 980-8578 (Japan); Miyamoto, Mitsutaka [Shimane University, Matsue, Shimane 690-8504 (Japan); Nakamura, Hiroaki [National Institute for Fusion Science, 322-6 Oroshi-cho, Toki 509-5292 (Japan); Nagoya University, Furo-cho, Chikusa-ku, Nagoya 464-8603 (Japan)

2015-08-15

The generation of tungsten fuzzy nanostructure by exposure to helium plasma is one of the important problems for the use of tungsten material as divertor plates in nuclear fusion reactors. In the present paper, the formation mechanisms of the helium bubble and the tungsten fuzzy nanostructure were investigated by using several simulation methods. We proposed the four-step process which is composed of penetration step, diffusion and agglomeration step, helium bubble growth step, and fuzzy nanostructure formation step. As the fourth step, the formation of the tungsten fuzzy nanostructure was successfully reproduced by newly developed hybrid simulation combining between molecular dynamics and Monte-Carlo method. The formation mechanism of tungsten fuzzy nanostructure observed by the hybrid simulation is that concavity and convexity of the surface are enhanced by the bursting of helium bubbles in the region around the concavity.

Chrysosplenium japonicum (Saxifragaceae, Newly Recorded from Taiwan

Directory of Open Access Journals (Sweden)

Tian-Chuan Hsu

2011-11-01

Full Text Available Chrysosplenium japonicum (Maxim. Makino (Saxifragaceae is newly recorded from northeastern Taiwan. Description, color photos and a key to the Chrysosplenium species in Taiwan are provided.

Computer-aided trauma simulation system with haptic feedback is easy and fast for oral-maxillofacial surgeons to learn and use.

Science.gov (United States)

Schvartzman, Sara C; Silva, Rebeka; Salisbury, Ken; Gaudilliere, Dyani; Girod, Sabine

2014-10-01

Computer-assisted surgical (CAS) planning tools have become widely available in craniomaxillofacial surgery, but are time consuming and often require professional technical assistance to simulate a case. An initial oral and maxillofacial (OM) surgical user experience was evaluated with a newly developed CAS system featuring a bimanual sense of touch (haptic). Three volunteer OM surgeons received a 5-minute verbal introduction to the use of a newly developed haptic-enabled planning system. The surgeons were instructed to simulate mandibular fracture reductions of 3 clinical cases, within a 15-minute time limit and without a time limit, and complete a questionnaire to assess their subjective experience with the system. Standard landmarks and linear and angular measurements between the simulated results and the actual surgical outcome were compared. After the 5-minute instruction, all 3 surgeons were able to use the system independently. The analysis of standardized anatomic measurements showed that the simulation results within a 15-minute time limit were not significantly different from those without a time limit. Mean differences between measurements of surgical and simulated fracture reductions were within current resolution limitations in collision detection, segmentation of computed tomographic scans, and haptic devices. All 3 surgeons reported that the system was easy to learn and use and that they would be comfortable integrating it into their daily clinical practice for trauma cases. A CAS system with a haptic interface that capitalizes on touch and force feedback experience similar to operative procedures is fast and easy for OM surgeons to learn and use. Copyright © 2014 American Association of Oral and Maxillofacial Surgeons. All rights reserved.

Beam Delivery Simulation: BDSIM - Development & Optimization

CERN Document Server

Nevay, Laurence James; Garcia-Morales, H; Gibson, S M; Kwee-Hinzmann, R; Snuverink, J; Deacon, L C

2014-01-01

Beam Delivery Simulation (BDSIM) is a Geant4 and C++ based particle tracking code that seamlessly tracks particles through accelerators and detectors, including the full range of particle interaction physics processes from Geant4. BDSIM has been successfully used to model beam loss and background conditions for many current and future linear accelerators such as the Accelerator Test Facility 2 (ATF2) and the International Linear Collider (ILC). Current developments extend its application for use with storage rings, in particular for the Large Hadron Collider (LHC) and the High Luminosity upgrade project (HL-LHC). This paper presents the latest results from using BDSIM to model the LHC as well as the developments underway to improve performance.

Developments in regional scale simulation: modelling ecologically sustainable development in the Northern Territory

International Nuclear Information System (INIS)

Moffatt, I.

1992-01-01

This paper outlines one way in which researchers can make a positive methodological contribution to the debate on ecologically sustainable development (ESD) by integrating dynamic modelling and geographical information systems to form the basis for regional scale simulations. Some of the orthodox uses of Geographic Information System (GIS) are described and it is argued that most applications do not incorporate process based causal models. A description of a pilot study into developing a processed base model of ESD in the Northern Territory is given. This dynamic process based simulation model consists of two regions namely the 'Top End' and the 'Central' district. Each region consists of ten sub-sectors and the pattern of land use represents a common sector to both regions. The role of environmental defence expenditure, including environmental rehabilitation of uranium mines, in the model is noted. Similarly, it is hypothesized that the impact of exogenous changes such as the greenhouse effect and global economic fluctuations can have a differential impact on the behaviour of several sectors of the model. Some of the problems associated with calibrating and testing the model are reviewed. Finally, it is suggested that further refinement of this model can be achieved with the pooling of data sets and the development of PC based transputers for more detailed and accurate regional scale simulations. When fully developed it is anticipated that this pilot model can be of service to environmental managers and other groups involved in promoting ESD in the Northern Territory. 54 refs., 6 figs

Development of Technical Skills: Education, Simulation, and Maintenance of Certification.

Science.gov (United States)

Sullivan, Sarah A; Anderson, Barbara M H; Pugh, Carla M

2015-11-01

The goal of this article is to provide a focused overview of technical skills education inside the operating room (OR), opportunities for learning outside of the OR (with a focus on simulation), and methods for measuring technical skills. In addition, the authors review the role of maintenance of certification in continuing education and quality improvement and consider the role that simulation plays in this process. The perspectives on teaching in the OR of both residents and faculty going into the case affect the learning environment, and preoperative interactions between attendings and residents to establish learning needs and goals are important. Furthermore, in regards to attending surgeons improving their skills, interaction with more experienced peers and feedback during and after a procedure can be beneficial. Simulation is increasingly being utilized as an education tool outside of the OR. Training in plastic surgery is poised to exploit simulation in multiple technical areas. There is potential to utilize these simulation environments to collect real-time data, such as motion, visual focus, and pressure. How to incorporate technical skill evaluation results in ways that are most beneficial for learning should be the focus of future research and curriculum development. Finally, simulation could be better utilized as a mechanism for both self and peer evaluation and assessment for continuing education and quality improvement. Professional development for faculty and surgery trainees on how to engage with simulation for teaching and learning and how to translate these experiences into improving patient care will be required.

Measuring participants' immersion in healthcare simulation: the development of an instrument.

Science.gov (United States)

Hagiwara, Magnus Andersson; Backlund, Per; Söderholm, Hanna Maurin; Lundberg, Lars; Lebram, Mikael; Engström, Henrik

2016-01-01

Immersion is important for simulation-based education; however, questionnaire-based instruments to measure immersion have some limitations. The aim of the present work is to develop a new instrument to measure immersion among participants in healthcare simulation scenarios. The instrument was developed in four phases: trigger identification, content validity scores, inter-rater reliability analysis and comparison with an existing immersion measure instrument. A modified Delphi process was used to develop the instrument and to establish validity and reliability. The expert panel consisted of 10 researchers. All the researchers in the team had previous experience of simulation in the health and/or fire and rescue services as researchers and/or educators and simulation designers. To identify triggers, the panel members independently screened video recordings from simulation scenarios. Here, a trigger is an event in a simulation that is considered a sign of reduced or enhanced immersion among simulation participants. The result consists of the Immersion Score Rating Instrument (ISRI). It contains 10 triggers, of which seven indicate reduced and three enhanced immersion. When using ISRI, a rater identifies trigger occurrences and assigns them strength between 1 and 3. The content validity analysis shows that all the 10 triggers meet an acceptable content validity index for items (I-CVI) standard. The inter-rater reliability (IRR) among raters was assessed using a two-way mixed, consistency, average-measures intra-class correlation (ICC). The ICC for the difference between weighted positive and negative triggers was 0.92, which indicates that the raters are in agreement. Comparison with results from an immersion questionnaire mirrors the ISRI results. In conclusion, we present a novel and non-intrusive instrument for identifying and rating the level of immersion among participants in healthcare simulation scenarios.

Development on Dose Assessment Model of Northeast Asia Nuclear Accident Simulator

Energy Technology Data Exchange (ETDEWEB)

Kim, Ju Yub; Kim, Ju Youl; Kim, Suk Hoon; Lee, Seung Hee; Yoon, Tae Bin [FNC Techology, Yongin (Korea, Republic of)

2016-05-15

In order to support the emergency response system, the simulator for overseas nuclear accident is under development including source-term estimation, atmospheric dispersion modeling and dose assessment. The simulator is named NANAS (Northeast Asia Nuclear Accident Simulator). For the source-term estimation, design characteristics of each reactor type should be reflected into the model. Since there are a lot of reactor types in neighboring countries, the representative reactors of China, Japan and Taiwan have been selected and the source-term estimation models for each reactor have been developed, respectively. For the atmospheric dispersion modeling, Lagrangian particle model will be integrated into the simulator for the long range dispersion modeling in Northeast Asia region. In this study, the dose assessment model has been developed considering external and internal exposure. The dose assessment model has been developed as a part of the overseas nuclear accidents simulator which is named NANAS. It addresses external and internal pathways including cloudshine, groundshine and inhalation. Also, it uses the output of atmospheric dispersion model (i.e. the average concentrations of radionuclides in air and ground) and various coefficients (e.g. dose conversion factor and breathing rate) as an input. Effective dose and thyroid dose for each grid in the Korean Peninsula region are printed out as a format of map projection and chart. Verification and validation on the dose assessment model will be conducted in further study by benchmarking with the measured data of Fukushima Daiichi Nuclear Accident.

GNSSim: An Open Source GNSS/GPS Framework for Unmanned Aerial Vehicular Network Simulation

Directory of Open Access Journals (Sweden)

Farha Jahan

2015-08-01

Full Text Available Unmanned systems are of great importance in accomplishing tasks where human lives are at risk. These systems are being deployed in tasks that are time-consuming, expensive or inconclusive if accomplished by human intervention. Design, development and testing of such vehicles using actual hardware could be quite costly and dangerous. Another issue is the limited outdoor usage permitted by Federal Aviation Administration regulations, which makes outdoor testing difficult. An optimal solution to this problem is to have a simulation environment where different operational scenarios, newly developed models, etc., can be studied. In this paper, we propose GNSSim, a Global Navigation Satellite System (GNSS simulation framework. We demonstrate its effectiveness by integrating it with UAVSim. This allows users to experiment easily by adjusting different satellite as well as UAV parameters. Related tests and evidence of the correctness of the implementation are presented.

Development of automation and robotics for space via computer graphic simulation methods

Science.gov (United States)

Fernandez, Ken

1988-01-01

A robot simulation system, has been developed to perform automation and robotics system design studies. The system uses a procedure-oriented solid modeling language to produce a model of the robotic mechanism. The simulator generates the kinematics, inverse kinematics, dynamics, control, and real-time graphic simulations needed to evaluate the performance of the model. Simulation examples are presented, including simulation of the Space Station and the design of telerobotics for the Orbital Maneuvering Vehicle.

Development of research reactor simulator and its application to dynamic test-bed

International Nuclear Information System (INIS)

Kwon, Kee-Choon; Baang, Dane; Park, Jae-Chang; Lee, Seung-Wook; Bae, Sung Won

2014-01-01

We developed a real-time simulator for 'High-flux Advanced Neutron Application ReactOr (HANARO), and the Jordan Research and Training Reactor (JRTR). The main purpose of this simulator is operator training, but we modified this simulator into a dynamic test-bed (DTB) to test the functions and dynamic control performance of reactor regulating system (RRS) in HANARO or JRTR before installation. The simulator hardware consists of a host computer, 6 operator stations, a network switch, and a large display panel. The software includes a mathematical model that implements plant dynamics in real-time, an instructor station module that manages user instructions, and a human machine interface module. The developed research reactor simulators are installed in the Korea Atomic Energy Research Institute nuclear training center for reactor operator training. To use the simulator as a dynamic test-bed, the reactor regulating system modeling software of the simulator was replaced by actual RRS cabinet, and was interfaced using a hard-wired and network-based interface. RRS cabinet generates control signals for reactor power control based on the various feedback signals from DTB, and the DTB runs plant dynamics based on the RRS control signals. Thus the Hardware-In-the-Loop Simulation between RRS and the emulated plant (DTB) has been implemented and tested in this configuration. The test result shows that the developed DTB and actual RRS cabinet works together simultaneously resulting in quite good dynamic control performances. (author)

Development of NDT simulator for corrosion detection using EMAT sensors

International Nuclear Information System (INIS)

Kojima, Fumio; Torigoe, Yoshifumi

2007-01-01

This paper is concerned with a simulator related to nondestructive test using Electromagnetic Acoustic Transducer (EMAT). The simulator developed here can be applied to corrosion detection of SUS samples used in nuclear power plants. First, mathematical models for the inspection are given by a transient eddy current equation and by a time dependent elastic wave equation in two dimensions. Secondly, finite element method is adopted to the mathematical model considered here. Finally, the validity of the proposed simulator is shown in the numerical experiments. (author)

Progress in Development of the ITER Plasma Control System Simulation Platform

Science.gov (United States)

Walker, Michael; Humphreys, David; Sammuli, Brian; Ambrosino, Giuseppe; de Tommasi, Gianmaria; Mattei, Massimiliano; Raupp, Gerhard; Treutterer, Wolfgang; Winter, Axel

2017-10-01

We report on progress made and expected uses of the Plasma Control System Simulation Platform (PCSSP), the primary test environment for development of the ITER Plasma Control System (PCS). PCSSP will be used for verification and validation of the ITER PCS Final Design for First Plasma, to be completed in 2020. We discuss the objectives of PCSSP, its overall structure, selected features, application to existing devices, and expected evolution over the lifetime of the ITER PCS. We describe an archiving solution for simulation results, methods for incorporating physics models of the plasma and physical plant (tokamak, actuator, and diagnostic systems) into PCSSP, and defining characteristics of models suitable for a plasma control development environment such as PCSSP. Applications of PCSSP simulation models including resistive plasma equilibrium evolution are demonstrated. PCSSP development supported by ITER Organization under ITER/CTS/6000000037. Resistive evolution code developed under General Atomics' Internal funding. The views and opinions expressed herein do not necessarily reflect those of the ITER Organization.

People newly in love are more responsive to positive feedback.

Science.gov (United States)

Brown, Cassandra L; Beninger, Richard J

2012-06-01

Passionate love is associated with increased activity in dopamine-rich regions of the brain. Increased dopamine in these regions is associated with a greater tendency to learn from reward in trial-and-error learning tasks. This study examined the prediction that individuals who were newly in love would be better at responding to reward (positive feedback). In test trials, people who were newly in love selected positive outcomes significantly more often than their single (not in love) counterparts but were no better at the task overall. This suggests that people who are newly in love show a bias toward responding to positive feedback, which may reflect a general bias towards reward-seeking.

Development and application of a tree-code in simulation scenarios of the plasma-wall interaction

International Nuclear Information System (INIS)

Berberich, Benjamin

2012-03-01

between numerical findings and semi-analytical results from the literature is achieved. After that verification a broad set of physical parameters are reviewed and corresponding scenarios evaluated. Explicitly the work focuses on the ion kinetics at the sheath edge. Numerical findings in that particular region compare well to established benchmarks in the collisionless limit. Furthermore results with rotated magnetic fields are presented. In the underlying simulations the newly developed guiding-center integrator is applied. Dedicated comparisons of the findings show good agreement with former theoretical and numerical approaches. A significant strength of the self-consistent mesh-free concept is its natural capability for including close range Coulomb interactions among charged particles. In this way it is possible, to consider intrinsically collisional scenarios such as the effect of ion-ion collisions on the presheath. Additionally a new developed Monte-Carlo background-scatter-scheme is utilized to introduce charge-exchange collisions into the presheath kinetics of the ions. These last two analyses show little change in sheath-relevant quantities. So the presented results support the widely held view that a viscosity or collisional dominated presheath has little effect on the sheath itself.

Simulation technology to develop the automatic control rod operation system in ABWR

Energy Technology Data Exchange (ETDEWEB)

Yoshihiko, Ishii; Atsushi, Fushimi; Naoyuki, Ishida [Hitachi Ltd. Power and Industrial Systems R and D Laboratory, Ibaraki (Japan); Hitoshi, Ochi; Masakazu, Yuzuki [Hitachi Ltd. Power Systems, Hitachi Works, Ibaraki (Japan); Hideki, Hanami [Hitachi Ltd. Information and Control System Div., Ibaraki (Japan)

2007-07-01

To design and verify the automatic power regulator system (APR) for an advanced boiling water reactor (ABWR), Hitachi has developed a plant simulation code system. The 3-dimensional kinetic analysis code STAND, based on a polynomial nodal expansion method, was effective in developing an APR automatic control rod operation algorithm in the critical mode. The point kinetic plant simulator AUTSIMU is an off-line and real time online plant simulation code that can simulate ABWR start-up and shutdown processes from a sub-critical condition with a water temperature of 20 degrees C to the rated operation power level at about 7 MPa. APR operation algorithms were designed using the off-line mode. In this mode, less than one minute in real time was needed to simulate a ten-hour transient with an ordinary personal computer. In the online mode, APR hardware was efficiently verified in a factory test before shipping. The codes were verified with ABWR start-up experimental data. It was confirmed that the simulators were effective in simulating ABWR plant start-up behavior. (authors)

Different patterns in the risk of newly developed fatty liver and lipid changes with tamoxifen versus aromatase inhibitors in postmenopausal women with early breast cancer: A propensity score-matched cohort study.

Science.gov (United States)

Hong, Namki; Yoon, Han Gyul; Seo, Da Hea; Park, Seho; Kim, Seung Il; Sohn, Joo Hyuk; Rhee, Yumie

2017-09-01

Management of metabolic complications of long-term adjuvant endocrine therapy in early breast cancer remained an unmet need. We aimed to compare the effects of tamoxifen (TMX) and aromatase inhibitors (AIs) on the risk of fatty liver in conjunction with longitudinal changes in the serum lipid parameters. Among 1203 subjects who were taking adjuvant TMX or AI (anastrozole or letrozole) without fatty liver at baseline, those taking TMX or AI were 1:1 matched on the propensity score. The primary outcome was newly developed fatty liver detected on annual liver ultrasonography. Among 328 matched subjects (mean age 53.5 years, body mass index 22.9 kg/m 2 ), 62 cases of fatty liver in the TMX group and 41 cases in the AI group were detected in a total of 987.4 person-years. The incidence rate of fatty liver was higher in the TMX group than in the AI group (128.7 versus 81.1 per 1000 person-years, P = 0.021), particularly within the first 2 years of therapy. TMX was associated with an increased 5-year risk of newly developed fatty liver (adjusted hazard ratio 1.61, P = 0.030) compared with AI independent of obesity and cholesterol level. Subjects who developed fatty liver had higher triglycerides (TGs) and lower high-density lipoprotein cholesterol (HDL-C) level at baseline than those without, which was sustained during follow-up despite the serum cholesterol-lowering effect of TMX. TMX independently increased the 5-year risk of newly developed fatty liver compared with AI in postmenopausal women with early breast cancer. Our findings suggest the need for considering the risk of fatty liver as a different adverse event profile between AI and TMX, particularly in patients with obesity, high TGs and low HDL-C. Copyright © 2017 Elsevier Ltd. All rights reserved.

Preliminary assessment of faculty and student perception of a haptic virtual reality simulator for training dental manual dexterity.

Science.gov (United States)

Gal, Gilad Ben; Weiss, Ervin I; Gafni, Naomi; Ziv, Amitai

2011-04-01

Virtual reality force feedback simulators provide a haptic (sense of touch) feedback through the device being held by the user. The simulator's goal is to provide a learning experience resembling reality. A newly developed haptic simulator (IDEA Dental, Las Vegas, NV, USA) was assessed in this study. Our objectives were to assess the simulator's ability to serve as a tool for dental instruction, self-practice, and student evaluation, as well as to evaluate the sensation it provides. A total of thirty-three evaluators were divided into two groups. The first group consisted of twenty-one experienced dental educators; the second consisted of twelve fifth-year dental students. Each participant performed drilling tasks using the simulator and filled out a questionnaire regarding the simulator and potential ways of using it in dental education. The results show that experienced dental faculty members as well as advanced dental students found that the simulator could provide significant potential benefits in the teaching and self-learning of manual dental skills. Development of the simulator's tactile sensation is needed to attune it to genuine sensation. Further studies relating to aspects of the simulator's structure and its predictive validity, its scoring system, and the nature of the performed tasks should be conducted.

Toward anthropomimetic robotics: development, simulation, and control of a musculoskeletal torso.

Science.gov (United States)

Wittmeier, Steffen; Alessandro, Cristiano; Bascarevic, Nenad; Dalamagkidis, Konstantinos; Devereux, David; Diamond, Alan; Jäntsch, Michael; Jovanovic, Kosta; Knight, Rob; Marques, Hugo Gravato; Milosavljevic, Predrag; Mitra, Bhargav; Svetozarevic, Bratislav; Potkonjak, Veljko; Pfeifer, Rolf; Knoll, Alois; Holland, Owen

2013-01-01

Anthropomimetic robotics differs from conventional approaches by capitalizing on the replication of the inner structures of the human body, such as muscles, tendons, bones, and joints. Here we present our results of more than three years of research in constructing, simulating, and, most importantly, controlling anthropomimetic robots. We manufactured four physical torsos, each more complex than its predecessor, and developed the tools required to simulate their behavior. Furthermore, six different control approaches, inspired by classical control theory, machine learning, and neuroscience, were developed and evaluated via these simulations or in small-scale setups. While the obtained results are encouraging, we are aware that we have barely exploited the potential of the anthropomimetic design so far. But, with the tools developed, we are confident that this novel approach will contribute to our understanding of morphological computation and human motor control in the future.

Development of the Object-Oriented Dynamic Simulation Models Using Visual C++ Freeware

Directory of Open Access Journals (Sweden)

Alexander I. Kozynchenko

2016-01-01

Full Text Available The paper mostly focuses on the methodological and programming aspects of developing a versatile desktop framework to provide the available basis for the high-performance simulation of dynamical models of different kinds and for diverse applications. So the paper gives some basic structure for creating a dynamical simulation model in C++ which is built on the Win32 platform with an interactive multiwindow interface and uses the lightweight Visual C++ Express as a free integrated development environment. The resultant simulation framework could be a more acceptable alternative to other solutions developed on the basis of commercial tools like Borland C++ or Visual C++ Professional, not to mention the domain specific languages and more specialized ready-made software such as Matlab, Simulink, and Modelica. This approach seems to be justified in the case of complex research object-oriented dynamical models having nonstandard structure, relationships, algorithms, and solvers, as it allows developing solutions of high flexibility. The essence of the model framework is shown using a case study of simulation of moving charged particles in the electrostatic field. The simulation model possesses the necessary visualization and control features such as an interactive input, real time graphical and text output, start, stop, and rate control.

[Development of APSIM (agricultural production systems simulator) and its application].

Science.gov (United States)

Shen, Yuying; Nan, Zhibiao; Bellotti, Bill; Robertson, Michael; Chen, Wen; Shao, Xinqing

2002-08-01

Soil-crop simulator model is an effective tool for providing decision on agricultural management. APSIM (Agricultural Production Systems Simulator) was developed to simulate the biophysical process in farming system, and particularly in the economic and ecological features of the systems under climatic risk. The current literatures revealed that APSIM could be applied in wide zone, including temperate continental, temperate maritime, sub-tropic and arid climate, and Mediterranean climates, with the soil type of clay, duplex soil, vertisol, silt sandy, silt loam and silt clay loam. More than 20 crops have been simulated well. APSIM is powerful on describing crop structure, crop sequence, yield prediction, and quality control as well as erosion estimation under different planting pattern.

Workplace Violence and Job Outcomes of Newly Licensed Nurses

OpenAIRE

Chang, Hyoung Eun; Cho, Sung-Hyun

2016-01-01

Purpose: The purpose of this study was to examine the prevalence of workplace violence toward newly licensed nurses and the relationship between workplace violence and job outcomes. Methods: An online survey was conducted of newly licensed registered nurses who had obtained their license in 2012 or 2013 in South Korea and had been working for 5–12 months after first being employed. The sample consisted of 312 nurses working in hospitals or clinics. The Copenhagen Psychosocial Questionnaire...

Development of a new graphical interface for the LABIHS simulator using LABVIEW

Energy Technology Data Exchange (ETDEWEB)

Augusto, Silas C.; Jaime, Guilherme D.; Farias, Marcos S., E-mail: silas@ien.gov.br, E-mail: gdjaime@ien.gov.br, E-mail: msantana@ien.gov.br [Instituto de Engenharia Nuclear (IEN/CNEN/RJ), Rio de Janeiro, RJ (Brazil)

2017-07-01

The LABIHS (Human-System Interfaces Laboratory) compact nuclear power plant (NPP) simulator is, since 2002, operating at the Nuclear Engineering Institute (IEN), Brazil. Due to the processing power required by the simulator software and the hardware available at the time, the simulator was developed under a PA-RISC architecture server (HPC3700), using the HP-UX operating system. All mathematical modeling components were written using the HP Fortran-77 programming language with a shared memory to exchange data from/to all simulator modules. In 2008, this hardware/software framework was discontinued, with customer support ceasing in 2013, what makes it difficult to maintain and expand. On the other hand, technological progress during this period enabled cheaper and more accessible computers, such as the PC (Personal Computer) architecture, to have enough processing power to run the simulator framework. It turns out that the PA-RISC computer architecture is incompatible with the PC one. Thus, our work group has been working, for some years, to port the simulator to the PC architecture. Part of this effort includes completely rebuilding all the MMI (Man- Machine Interface) using modern software tools and programming languages which are compatible with the PC architecture. In this work, we present two important steps for the NPP simulator migration from the obsolete architecture to the PC one. Firstly, we provide a new inter-process communication library which allows the data exchange between the NPP simulator currently running at the old PA-RISC architecture and other software running on modern PCs. This step is important because it allows to work on the new Graphical Interface while the older NPP simulator is still operating. Secondly, we present the all-new MMI for the LABIHS simulator, currently under development using LabVIEW software suit. We then provide a comparison between the original and the proposed MMI development process. (author)

Development of a new graphical interface for the LABIHS simulator using LABVIEW

International Nuclear Information System (INIS)

Augusto, Silas C.; Jaime, Guilherme D.; Farias, Marcos S.

2017-01-01