Jack Michael's Motivation

Science.gov (United States)

Miguel, Caio F.

2013-01-01

Among many of Jack Michael's contributions to the field of behavior analysis is his behavioral account of motivation. This paper focuses on the concept of "motivating operation" (MO) by outlining its development from Skinner's (1938) notion of "drive." Conceptually, Michael's term helped us change our focus on…

Cadmium accumulation by jack-bean and sorghum in hydroponic culture.

Science.gov (United States)

Francato Zancheta, Ariana Carramaschi; De Abreu, Cleide Aparecida; Zambrosi, Fernando César Bachiega; de Magalhães Erismann, Norma; Andrade Lagôa, Ana Maria Magalhães

2015-01-01

Among the technologies used to recuperate cadmium (Cd) contaminated soils, phytoextraction are particularly important, where the selection of suitable plants is critical to the success of the soil remediation. Thus, the objectives of this study were to evaluate the responses of jack-bean and sorghum to Cd supply and to quantify Cd accumulation by these species grown in hydroponic culture. The plants were subjected to 0, 15, 30, or 60 μmol Cd L(-1) in the nutrient solution, and gas exchange, plant growth and Cd accumulation were measured at 25 days after starting Cd treatments. The Cd supply severely reduced growth of shoots and roots in both species. In jack-bean, Cd decreased photosynthesis by 56-86%, stomatal conductance by 59-85% and transpiration by 48-80%. The concentrations and amounts of Cd accumulated in the plant tissues were proportional to the metal supply in the nutrient solution. Sorghum was more tolerant than jack-bean to Cd toxicity, but the latter showed a greater metal concentration and accumulation in the shoot. Therefore, jack-bean would be more suitable than sorghum for use in Cd phytoremediation programs based on phytoextraction.

Jacking mechanism for upper internals structure of a liquid metal nuclear reactor

International Nuclear Information System (INIS)

Gillett, J.E.; Wineman, A.L.

1984-01-01

A jacking mechanism is described for raising the upper internals structure of a liquid metal nuclear reactor which jacking mechanism uses a system of gears and drive shafts to transmit force from a single motor to four mechanically synchronized ball jacks to raise and lower support columns which support the upper internals structure. The support columns have a pin structure which rides up and down in a slot in a housing fixed to the reactor head. The pin has two locking plates which can be rotated around the pin to bring bolt holes through the locking plates into alignment with a set of bolt holes in the housing, there being a set of such housing bolt holes corresponding to both a raised and a lowered position of the support column. When the locking plate is so aligned, a surface of the locking plate mates with a surface in the housing such that the support column is then supported by the locking plate and not by the ball jacks. Since the locking plates are to be installed and bolted to the housing during periods of reactor operation, the ball jacks need not be sized to react the large forces which occur or potentially could occur on the upper internals structure of the reactor during operation. The locking plates react these loads. The ball jacks, used only during refueling, can be smaller, which enable conventionally available equipment to fulfill the precision requirements for the task within available space

Estudo da impressão plantar obtida durante o teste de Jack em crianças Footprint study in children during the Jack test

Directory of Open Access Journals (Sweden)

José Antonio Pinto

2011-01-01

Full Text Available OBJETIVO: Avaliar as impressões plantares durante o teste de Jack em crianças quantificando e observando os resultados numa faixa etária crítica para a formação do arco plantar. MÉTODO: Avaliamos 60 crianças brancas (120 pés sendo 35 meninos e 25 meninas com idades entre 2 e 5 anos, sem queixas ortopédicas. Simulamos o teste de Jack com uma órtese em cunha de 45º apoiada sob o hálux. Obtivemos impressões em apoio monopodálico bilateralmente utilizando um pedígrafo. O exame dividiu-se em duas etapas: com e sem o uso da órtese. A metodologia de Valenti e Volpon foi utilizada para mensurar as impressões plantares e os dados obtidos foram analisados estatisticamente. RESULTADOS: Os valores dos índices de Valenti e Volpon diminuiram quando a órtese foi utilizada. A diferença entre os índices com ou sem órtese diminuiu gradualmente com a progressão etária. CONCLUSÕES: É possível quantificar o teste de Jack pelwas impressões plantares pelo método de Valenti e Volpon. A variação do seu formato apresentou tendência a ser menor a partir dos 4 anos. O teste de Jack perdeu gradativamente a capacidade de modificar a impressão plantar com a idade, diminuindo sua acuidade como parâmetro de bom prognóstico na formação do arco longitudinal medial. Nível de Evidência: Nível IV, estudo descritivo observacional.OBJECTIVE: To assess the plantar impressions obtained in children during the Jack test, with the aim of quantifying and analyzing their variability in the critical period for plantar foot arch formation. METHOD: A hundred and twenty feet from 60 healthy White children, recruited in an outpatient pediatric clinic, were examined. Our sample included 35 boys and 25 girls, ranging from 2 to 5 years. The Jack test was simulated using a 45o wedge-shaped orthosis applied to the hallux. Bilateral plantar impressions were acquired in the alternate single-foot standing position using a pedigraph. Two plantar impressions were

Footprint study in children during the Jack test

OpenAIRE

Pinto, José Antonio; Saito, Edgar; Lira Neto, Ozório Almeida; Rowinski, Sérgio; Blumetti, Francesco Camara; Dobashi, Eiffel Tsuyoshi

2011-01-01

OBJETIVO: Avaliar as impressões plantares durante o teste de Jack em crianças quantificando e observando os resultados numa faixa etária crítica para a formação do arco plantar. MÉTODO: Avaliamos 60 crianças brancas (120 pés) sendo 35 meninos e 25 meninas com idades entre 2 e 5 anos, sem queixas ortopédicas. Simulamos o teste de Jack com uma órtese em cunha de 45º apoiada sob o hálux. Obtivemos impressões em apoio monopodálico bilateralmente utilizando um pedígrafo. O exame dividiu-se em dua...

Recollections of Jack Michael and the Application of Skinner's Analysis of Verbal Behavior

Science.gov (United States)

Sundberg, Mark L.

2017-01-01

Jack Michael offered a course on verbal behavior almost every year throughout his teaching career. Jack was also interested in the application of Skinner's work and in 1976 began to offer a graduate course at Western Michigan University titled Verbal Behavior Applications. Jack and his students pursued the application of Skinner's work on verbal…

An Analytical Method for Jack-Up Riser’s Fatigue Life Estimation

Directory of Open Access Journals (Sweden)

Fengde Wang

2018-01-01

Full Text Available In order to determine whether a special sea area and its sea state are available for the jack-up riser with surface blowout preventers, an analytical method is presented to estimate the jack-up riser’s wave loading fatigue life in this study. In addition, an approximate formula is derived to compute the random wave force spectrum of the small-scale structures. The results show that the response of jack-up riser is a narrow band random vibration. The infinite water depth dispersion relation between wavenumber and wave frequency can be used to calculate the wave force spectrum of small-scale structures. The riser’s response mainly consists of the additional displacement response. The fatigue life obtained by the formula proposed by Steinberg is less than that of the Bendat method.

Reproductive aspects of Jack mackerel Trachurus murphy

Directory of Open Access Journals (Sweden)

Ángel Perea

2013-10-01

Full Text Available The time series of monthly gonadosomatic index (GSI and biannual size at first maturity of Jack mackerel Trachurus murphyiNichols 1920 in Peru between 1967 and 2012 is analyzed and discussed. The annual and interannual variation of the reproductive cycle was determined. It is shown that in Peru T. murphyihas a single relatively extended spawning period with a maximum in November each year. It is also shown that for more than four decades T. murphyi has spawned regularly every year in Peruvian waters. The reproductive activity of T. murphyi has a greater variability off Peru and the spawning period has peaks of lesser magnitude but extend longer than observed in the spawning occurring off Chile. The analyses of the sizes at first maturity of Jack mackerel in Peruvian waters did not show significant changes throughout the entire period observed.

Topological color codes on Union Jack lattices: a stable implementation of the whole Clifford group

International Nuclear Information System (INIS)

Katzgraber, Helmut G.; Bombin, H.; Andrist, Ruben S.; Martin-Delgado, M. A.

2010-01-01

We study the error threshold of topological color codes on Union Jack lattices that allow for the full implementation of the whole Clifford group of quantum gates. After mapping the error-correction process onto a statistical mechanical random three-body Ising model on a Union Jack lattice, we compute its phase diagram in the temperature-disorder plane using Monte Carlo simulations. Surprisingly, topological color codes on Union Jack lattices have a similar error stability to color codes on triangular lattices, as well as to the Kitaev toric code. The enhanced computational capabilities of the topological color codes on Union Jack lattices with respect to triangular lattices and the toric code combined with the inherent robustness of this implementation show good prospects for future stable quantum computer implementations.

Seeing is believing -- SpyJack system investigates field problems

International Nuclear Information System (INIS)

O'Meara, D.

1998-01-01

The SpyJack Remote Monitoring System, a stand-alone, single-site remote well monitoring system that works off its own embedded controller is described. The supervisory control and data acquisition (SCADA) unit, developed by CORE Technologies Inc., has an integrated voice/alarm system, monitoring sensors installed at remote well sites continuously 24 hours a day with a digital camera, with 300 degrees of visual confirmation capability. It can also be used as a surveillance tool against terrorism as has been shown in the case of some recent debilitating attacks on remote wells in Alberta. SpyJack monitors flow rates and pressures, pumpjack stroke rates, sucker rod temperature, load cell and engine shut-off relay, as well as ambient temperature, tank levels, and motion detection. At the office, SpyJack Well Management Interface uses nine drop-down screens to take users through the remote monitoring and control of each site. The screens include production sensors, line sensors, dyno chart, environmental/safety sensors and sensor information and set up. Currently under development is the unsolicited dial-out capability. When implemented the system will send out information at pre-determined times, such as every four hours, or at specific times during the day. Compressing images to enable speedier downloading is also being planned

An experimental study of the mechanism of failure of rocks under borehole jack loading

Science.gov (United States)

Van, T. K.; Goodman, R. E.

1971-01-01

Laboratory and field tests with an experimental jack and an NX-borehole jack are reported. The following conclusions were made: Under borehole jack loading, a circular opening in a brittle solid fails by tensile fracturing when the bearing plate width is not too small. Two proposed contact stress distributions can explain the mechanism of tensile fracturing. The contact stress distribution factor is a material property which can be determined experimentally. The borehole tensile strength is larger than the rupture flexural strength. Knowing the magnitude and orientation of the in situ stress field, borehole jack test results can be used to determine the borehole tensile strength. Knowing the orientation of the in situ stress field and the flexural strength of the rock substance, the magnitude of the in situ stress components can be calculated. The detection of very small cracks is essential for the accurate determination of the failure loads which are used in the calculation of strengths and stress components.

Jack in the Box, Unit 1A

DEFF Research Database (Denmark)

Gammelgaard Nielsen, Anders

2011-01-01

In the assignment known as ‘JACK- in-the-box’ the aim is to foster col- laborative situations through man- aging a complex architectural issue. The aim is to conduct an integrat- ed teaching course that extends from an introductory outline pro- cess through to the project devel- opment phase...

Black-tailed jack rabbit movements and habitat utilization at the Idaho National Engineering Laboratory radioactive waste management complex

International Nuclear Information System (INIS)

Grant, J.C.

1983-01-01

In June 1982, a study of black-tailed jack rabbit (Lepus californicus) ecology was initiated at the Idaho National Engineering Laboratory Radioactive Waste Management Complex (RWMC). This study will provide data necessary to evaluate the role of jack rabbits in radionuclide transport away from the Subsurface Disposal Area of the RWMC. Primary goals are to document radionuclide concentrations in jack rabbit tissues, and determine population size, movement patterns, habitat use, and food habits of jack rabbits inhabiting the RWMC area. Study design and prelimianry results are discussed

Spin-singlet quantum Hall states and Jack polynomials with a prescribed symmetry

International Nuclear Information System (INIS)

Estienne, Benoit; Bernevig, B. Andrei

2012-01-01

We show that a large class of bosonic spin-singlet Fractional Quantum Hall model wavefunctions and their quasihole excitations can be written in terms of Jack polynomials with a prescribed symmetry. Our approach describes new spin-singlet quantum Hall states at filling fraction ν=(2k)/(2r-1) and generalizes the (k,r) spin-polarized Jack polynomial states. The NASS and Halperin spin-singlet states emerge as specific cases of our construction. The polynomials express many-body states which contain configurations obtained from a root partition through a generalized squeezing procedure involving spin and orbital degrees of freedom. The corresponding generalized Pauli principle for root partitions is obtained, allowing for counting of the quasihole states. We also extract the central charge and quasihole scaling dimension, and propose a conjecture for the underlying CFT of the (k,r) spin-singlet Jack states.

Comparison of Sparse and Jack-knife partial least squares regression methods for variable selection

DEFF Research Database (Denmark)

Karaman, Ibrahim; Qannari, El Mostafa; Martens, Harald

2013-01-01

The objective of this study was to compare two different techniques of variable selection, Sparse PLSR and Jack-knife PLSR, with respect to their predictive ability and their ability to identify relevant variables. Sparse PLSR is a method that is frequently used in genomics, whereas Jack-knife PL...

Stress analysis of jacks, frame and bearing connections, and drill rod for core sampler truck No. 2

International Nuclear Information System (INIS)

Ziada, H.H.

1995-01-01

This analysis evaluates the structural design adequacy of several components and connections for the rotary mode core sampler truck (RMCST) No. 2. This analysis was requested by the Characterization Equipment Group (WHC 1994a). The components addressed in this report are listed below: front jack assembly and connection to the truck chassis; rear jack assembly and connection to the truck chassis; center outrigger jacks and connection to the truck chassis; lower frame assembly and connection to the truck chassis; bolt connections for bearing plate assembly (for path of maximum load); traverse slide brackets and mounting of the traverse jack cylinders; and drill rod (failure loads)

Functional properties of unmodified and modified Jack bean ...

African Journals Online (AJOL)

The native Jack bean (Canavalia eniformis) starch was chemically modified through oxidation and acetylation. Proximate composition analysis revealed higher moisture, protein, fat and ash contents 'native unmodified than modified starches and higher yield in modified starches. Swelling capacity and solubility of all the ...

JACK LONDON ETNÓLOGO AMATEUR DEL PUGILISMO

Directory of Open Access Journals (Sweden)

Loïc Wacquant

2012-12-01

Full Text Available De los relatos que Jack London ha consagrado al boxeo, A Piece of Steak es sin dudas aquel que merece hoy nuestra mayor atención, e incluso un lugar en el panteón de los textos literarios sobre el Noble Arte, y junto a él otros tres títulos...

Jack Polynomials as Fractional Quantum Hall States and the Betti Numbers of the ( k + 1)-Equals Ideal

Science.gov (United States)

Zamaere, Christine Berkesch; Griffeth, Stephen; Sam, Steven V.

2014-08-01

We show that for Jack parameter α = -( k + 1)/( r - 1), certain Jack polynomials studied by Feigin-Jimbo-Miwa-Mukhin vanish to order r when k + 1 of the coordinates coincide. This result was conjectured by Bernevig and Haldane, who proposed that these Jack polynomials are model wavefunctions for fractional quantum Hall states. Special cases of these Jack polynomials include the wavefunctions of Laughlin and Read-Rezayi. In fact, along these lines we prove several vanishing theorems known as clustering properties for Jack polynomials in the mathematical physics literature, special cases of which had previously been conjectured by Bernevig and Haldane. Motivated by the method of proof, which in the case r = 2 identifies the span of the relevant Jack polynomials with the S n -invariant part of a unitary representation of the rational Cherednik algebra, we conjecture that unitary representations of the type A Cherednik algebra have graded minimal free resolutions of Bernstein-Gelfand-Gelfand type; we prove this for the ideal of the ( k + 1)-equals arrangement in the case when the number of coordinates n is at most 2 k + 1. In general, our conjecture predicts the graded S n -equivariant Betti numbers of the ideal of the ( k + 1)-equals arrangement with no restriction on the number of ambient dimensions.

The Jack Wills crowd: towards a sociology of an elite subculture.

Science.gov (United States)

King, Anthony; Smith, Daniel

2018-03-01

British sociologists have long been interested in youth sub-cultures. However British sociologists have tended to focus on working class subcultures and avoided engagement with exclusive sub-cultures of elite social groups. This article seeks to attend to this gap by examining the subculture of a British elite: ex-public school students at select universities in the UK in the twenty-first century. This group consists of a relatively small group of young adults, aged between 18 and 23, who attended public schools, especially one of the nine Clarendon schools (Eton, Winchester, Westminster, St. Paul's, Merchant Taylor's, Shrewsbury, Rugby, Harrow and Charterhouse), and were students at a selective group of British universities, primarily Oxford and Cambridge, Durham, Bristol, Exeter, Bath, Manchester, St Andrews and Edinburgh. The article examines the way in which this group has reconfigured and re-constituted itself in the face of globalizing challenges. Specifically, it examines the way in which participation of ex-public school students in events run by and under the patronage of the high street retailing company, Jack Wills, has played a galvanising role for this group in the last decade. The Jack Wills crowd is an example of how some young adults form exclusive social networks and reproduce prevailing forms of privilege. The social networks built around the Jack Wills subculture is likely to provide them with advantages in the job market through a prodigious network of connections and patrons. The Jack Wills subculture potentially contributions to the socio-economic reproduction of the higher professional middle classes. © London School of Economics and Political Science 2017.

Generalized Jack and Macdonald polynomials arising from AGT conjecture

Science.gov (United States)

Ohkubo, Y.

2017-01-01

We investigate the existence and the orthogonality of the generalized Jack symmetric functions which play an important role in the AGT relations. We show their orthogonality by deforming them to the generalized Macdonald symmetric functions.

Modeling of the Jacked Pile Static Load Test with PLAX 3D

Directory of Open Access Journals (Sweden)

Tautvydas Statkus

2016-12-01

Full Text Available In this article jacked pile installation technology and its current processes, altering the base physical and mechanical characteristics are discussed. For the jacked pile static load test simulation Plax 3D software was selected, the opportunities and developments were described. Model building, materials, models, model geometry, finite elements, boundary conditions and assumptions adopted in addressing problems described in detail. Three different tasks formulated and load-settlement dependence a comparison of the results with the experiment given. Conclusions are formulated according to the modeling results.

Is the lateral jack-knife position responsible for cases of transient neurapraxia?

Science.gov (United States)

Molinares, Diana Margarita; Davis, Timothy T; Fung, Daniel A; Liu, John Chung-Liang; Clark, Stephen; Daily, David; Mok, James M

2016-01-01

The lateral jack-knife position is often used during transpsoas surgery to improve access to the spine. Postoperative neurological signs and symptoms are very common after such procedures, and the mechanism is not adequately understood. The objective of this study is to assess if the lateral jack-knife position alone can cause neurapraxia. This study compares neurological status at baseline and after positioning in the 25° right lateral jack-knife (RLJK) and the right lateral decubitus (RLD) position. Fifty healthy volunteers, ages 21 to 35, were randomly assigned to one of 2 groups: Group A (RLD) and Group B (RLJK). Motor and sensory testing was performed prior to positioning. Subjects were placed in the RLD or RLJK position, according to group assignment, for 60 minutes. Motor testing was performed immediately after this 60-minute period and again 60 minutes thereafter. Sensory testing was performed immediately after the 60-minute period and every 15 minutes thereafter, for a total of 5 times. Motor testing was performed by a physical therapist who was blinded to group assignment. A follow-up call was made 7 days after the positioning sessions. Motor deficits were observed in the nondependent lower limb in 100% of the subjects in Group B, and no motor deficits were seen in Group A. Statistically significant differences (p knife positioning for 60 minutes results in neurapraxia of the nondependent lower extremity. Our results support the hypothesis that jack-knife positioning alone can cause postoperative neurological symptoms.

'Weightless' acrylic painting by Jack Kroehnke

Science.gov (United States)

1987-01-01

'Weightless' acrylic painting by Jack Kroehnke depicts STS-26 Discovery, Orbiter Vehicle (OV) 103, Mission Specialist (MS) David C. Hilmers participating in extravehicular activity (EVA) simulation in JSC Weightless Environment Training Facility (WETF) Bldg 29. In the payload bay (PLB) mockup, Hilmers, wearing extravehicular mobility unit (EMU), holds onto the mission-peculiar equipment support structure in foreground while SCUBA-equipped diver monitors activity overhead and camera operator records EVA procedures. Copyrighted art work for use by NASA.

Jack Reeves and his science.

Science.gov (United States)

Moore, Lorna G; Grover, Robert F

2006-04-28

John T. (Jack) Reeves' science is reviewed across the 37 years of his research career at the University of Colorado Health Sciences Center, a period which occupied approximately half his remarkable life. His contributions centered on understanding the inter-relatedness as well as the underlying mechanisms controlling the various components of the O(2) transport system. We review here his studies on exercise performance; these encompassed about half his scientific output with the other half being devoted to the study of hypoxic pulmonary hypertension. Early studies concerned cardiac output, showing how it was a balance between O(2) uptake and O(2) extraction, and that cardiac output during exercise at high altitude was reduced, most likely because of decreased plasma volume and left ventricular filling. Jack's many studies addressed virtually every aspect of the O(2) transport system -- adding significantly to our understanding of the syndromes of altitude illness, the mechanisms by which ventilatory sensitivity to hypoxia and hypercapnia influenced ventilatory acclimatization, and the contributions of the various limbs of the autonomic nervous system on systemic blood pressure, vascular resistance and substrate utilization. His scientific career ended abruptly in 2004 when struck by a car while biking to work, but his legacy remains in his more than 385+ research articles or chapters, the 40+ fellows he trained, and the countless number of younger (and older) scientists for whom he served as a role model for learning how to scrutinize their data and present their findings in clear and sometimes bold prose. An integral man, he is sorely missed.

Lithium in Jack Hills zircons: Evidence for extensive weathering of Earth's earliest crust

Science.gov (United States)

Ushikubo, Takayuki; Kita, Noriko T.; Cavosie, Aaron J.; Wilde, Simon A.; Rudnick, Roberta L.; Valley, John W.

2008-08-01

In situ Li analyses of 4348 to 3362 Ma detrital zircons from the Jack Hills, Western Australia by SIMS reveal that the Li abundances (typically 10 to 60 ppm) are commonly over 10,000 times higher than in zircons crystallized from mantle-derived magmas and in mantle-derived zircon megacrysts (typically Jack Hills zircons also have fractionated lithium isotope ratios ( δ7Li = - 19 to + 13‰) about five times more variable than those recorded in primitive ocean floor basalts (2 to 8‰), but similar to continental crust and its weathering products. Values of δ7Li below - 10‰ are found in zircons that formed as early as 4300 Ma. The high Li compositions indicate that primitive magmas were not the source of Jack Hills zircons and the fractionated values of δ7Li suggest that highly weathered regolith was sampled by these early Archean magmas. These new Li data provide evidence that the parent magmas of ancient zircons from Jack Hills incorporated materials from the surface of the Earth that interacted at low temperature with liquid water. These data support the hypothesis that continental-type crust and oceans existed by 4300 Ma, within 250 million years of the formation of Earth and the low values of δ7Li suggest that weathering was extensive in the early Archean.

Habitat Preferences, Distribution Pattern, and Root Weight Estimation of Pasak Bumi (Eurycoma longifolia Jack.

Directory of Open Access Journals (Sweden)

Siti Masitoh Kartikawati

2014-04-01

Full Text Available Pasak bumi (Eurycoma longifolia Jack is one of non timber forest products with “indeterminate” conservation status and commercially traded in West Kalimantan. The research objective was to determine the potential of pasak bumi root per hectare and its ecological condition under natural habitat. Root weight of E. longifolia Jack was estimated using simple linear regression and exponential equation with stem diameter and height as independent variables. The results showed that the individual number of the population was 114 with the majority in seedling stage with 71 individuals (62.28%. The distribution was found in clumped pattern. Conditions of the habitat could be described as follows: daily average temperature of 25.6oC, daily average relative humidity of 73.6%, light intensity of 0.9 klx, and red-yellow podsolic soil with texture ranged from clay to sandy clay. The selected estimator model for E. longifolia Jack root weight used exponential equation with stem height as independent variable using the equation of Y= 21.99T0,010 and determination coefficient of 0.97. After height variable was added, the potential of E. longifolia Jack minimum root weight that could be harvested per hectare was 0.33 kg.Keywords: Eurycoma longifolia, habitat preference, distribution pattern, root weight

Book Review: Jack Simons: Teacher, Scholar, Comrade: A Jacana ...

African Journals Online (AJOL)

Book Title: Jack Simons: Teacher, Scholar, Comrade: A Jacana Pocket Biography. Book Author: Hugh Macmillan. Jacana: Auckland Park, 2016. 167 pp. Full Text: EMAIL FULL TEXT EMAIL FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT · AJOL African Journals Online. HOW TO USE AJOL.

Purification, crystallization and preliminary X-ray analysis of urease from jack bean (Canavalia ensiformis)

International Nuclear Information System (INIS)

Balasubramanian, Anuradha; Ponnuraj, Karthe

2009-01-01

Jack bean urease was purified and crystallized and X-ray diffraction data were collected to 2.05 Å resolution. Plant urease is a seed protein that is common in most legumes. It is also common in many bacteria and fungi and several species of yeast. Urease allows organisms to use exogenous and internally generated urea as a nitrogen source by catalyzing the hydrolysis of urea to ammonia and carbon dioxide. Urease from jack bean meal was purified to electrophoretic homogeneity using a series of steps involving acetone precipitation and size-exclusion and ion-exchange chromatography. The jack bean urease was crystallized and the resulting crystals diffracted to 2.05 Å resolution using synchrotron radiation. The crystals belonged to the hexagonal space group P6 3 22, with unit-cell parameters a = b = 138.57, c = 198.36 Å

Pangad õhutavad III pensionisambaga liituma / Toivo Tänavsuu

Index Scriptorium Estoniae

Tänavsuu, Toivo

2004-01-01

Pangad peavad III pensionisambaga liitumist hädavajalikuks neile, kes soovivad oma elustandardit pensionile minnes säilitada. Pankade prognoose III sambaga liitumise kohta käesolevaks aastaks. Lisa: Pensioniks kogumine

Geographic variation of jack pine (Pinus banksiana Lamb.)

Science.gov (United States)

Jung Oh Hyun

1977-01-01

Ten traits were measured on 10-year-old jack pine grown at Cloquet, Minnesota, from seed collected from 90 provenances. The traits were examined by using analysis of variance and computing correlations for all combinations of 9 traits plus latitude , longitude, and elevation of the seed sources and cluster analyses using the D2 values from the...

JackEx: The new digital manufacturing resource for optimization of Exoskeleton-based factory environments

OpenAIRE

Constantinescu, Carmen; Mureșan, Paul Cristian; Simon, Gabriel-Marian

2016-01-01

The employment of Exoskeletons for manual handling work in manufacturing industries aims at increased employment, productivity, safety and security at workplace. This paper highlights several challenges, current results and future steps of our work in optimization of Exoskeleton based factory environments. “JackEx” is the enhancement of the standard digital humanoid “Jack” with concepts and elements of passive Exoskeletons. For the development of JackEx, a new digital manufacturing resource, ...

Seismic analysis of the frame structure reformed by cutting off column and jacking based on stiffness ratio

Science.gov (United States)

Zhao, J. K.; Xu, X. S.

2017-11-01

The cutting off column and jacking technology is a method for increasing story height, which has been widely used and paid much attention in engineering. The stiffness will be changed after the process of cutting off column and jacking, which directly affects the overall seismic performance. It is usually necessary to take seismic strengthening measures to enhance the stiffness. A five story frame structure jacking project in Jinan High-tech Zone was taken as an example, and three finite element models were established which contains the frame model before lifting, after lifting and after strengthening. Based on the stiffness, the dynamic time-history analysis was carried out to research its seismic performance under the EL-Centro seismic wave, the Taft seismic wave and the Tianjin artificial seismic wave. The research can provide some guidance for the design and construction of the entire jack lifting structure.

Jack Michael's Musings on the 60th Anniversary of Skinner's "Verbal Behavior"

Science.gov (United States)

Esch, Barbara E.; Esch, John W.; Palmer, David C.

2017-01-01

When the B. F. Skinner Foundation reprinted Skinner's "Verbal Behavior" in 1992, Jack Michael wrote one of its two forewords, a detailed outline of the book's purpose and scope. On the 60th anniversary of the first publication (1957) of "Verbal Behavior", Jack reflects on the book's impact and its importance to the…

Investigating the Jack the Ripper Case: Engaging Students in a Criminal Investigations Class through Active Learning

Science.gov (United States)

Gutierrez, Daniel; Kazmi, Syed

2010-01-01

The present study examines the utilization of a class project involving the Jack the Ripper murders. Students enrolled in a criminal investigations class were required to investigate the five canonical murders associated with the infamous serial killer known as Jack the Ripper and the murders that occurred in London during 1888. This paper…

Manager's handbook for jack pine in the north central states.

Science.gov (United States)

John W. Benzie

1977-01-01

Provides a key for the resource manager to use in choosing silvicultural practices for the management of jack pine. Control of stand composition, growth, and stand establishment for timber production, water, wildlife, and recreation are discussed.

Teistsugune vaade juhtide tasustamisele / Jack Welch, Suzy Welch ; intervjueerinud Stefan Eiselin

Index Scriptorium Estoniae

Welch, Jack

2010-01-01

USA juhtimisspetsialistide Jack ja Suzy Welchi hinnangul võib tippjuhtidele makstava palga ümber kerkinud poleemika üks võimalikke põhjuseid lisaks halvale kommunikatsioonile olla ka ideoloogiate kokkusobimatus

Uus valem otsustamiseks: 10-10-10 / Jack Welch, Suzy Welch

Index Scriptorium Estoniae

Welch, Jack

2009-01-01

Juhtimisspetsialistid Jack ja Suzy Welch tutvustavad enda loodud valemit 10-10-10, mis on elu juhtimise tööriist aitamaks langetada raskeid otsuseid, hinnates nende mõju 10 minuti, 10 kuu ja 10 aasta pärast

The Bildungsroman Tradition: The Philosophical Maturation of Jack Burden in All the King’s Men

Directory of Open Access Journals (Sweden)

Bassam M. Al-Shraah

2017-11-01

Full Text Available This paper aims to sketch out the transformation that Jack Burden—the main character in the novel—had gone through. With all the political leanings in Warren’s All the king’s Men, Jack burden seems to have had developed his own theories of dealing with life and people all through his life. He has always suffered an inferiority complex, rendering himself unworthy of being a real human being. This paper claims that Jack’s philosophical transformation has passed through three distinct phases; he had changed from a carefree idealist to a man of moral responsibility much similar to a Bildungsroman style of character maturation. Difficult times that Jack Burden has gone through caused his awakening at the end of the novel ushering his maturation

Facile synthesis of highly branched jacks-like ZnO nanorods and their applications in dye-sensitized solar cells

International Nuclear Information System (INIS)

Sudhagar, P.; Kumar, R. Saravana; Jung, June Hyuk; Cho, Woohyung; Sathyamoorthy, R.; Won, Jongok; Kang, Yong Soo

2011-01-01

Graphical abstract: -- Abstract: Highly branched, jacks-like ZnO nanorods architecture were explored as a photoanode in dye-sensitized solar cells, and their photovoltaic performance was compared with that of branch-free ZnO nanorods photoanodes. The highly branched network and large pores of the jacks-like ZnO nanorods electrodes enhances the charge transport, and electrolyte penetration. Thus, the jacks-like ZnO nanorods DSSCs render a higher conversion efficiency of η = 1.82% (V oc = 0.59 V, J sc = 5.52 mA cm -2 ) than that of the branch-free ZnO nanorods electrodes (η = 1.08%, V oc = 0.49 V, J sc = 4.02 mA cm -2 ). The incident photon-to-current conversion efficiency measurements reveal that the jacks-like ZnO nanorods DSSCs exhibit higher internal quantum efficiency (∼59.1%) than do the branch-free ZnO nanorods DSSC (∼52.5%). The charge transfer resistances at the ZnO/dye/electrolyte interfaces investigated using electrochemical impedance spectroscopy showed that the jacks-like ZnO nanorods DSSC had high charge transfer resistance and a slightly longer electron lifetime, thus improving the solar-cell performance.

Facile synthesis of highly branched jacks-like ZnO nanorods and their applications in dye-sensitized solar cells

Energy Technology Data Exchange (ETDEWEB)

Sudhagar, P. [Center for Next Generation Dye-sensitized Solar Cells, WCU Program Department of Energy Engineering, Hanyang University, Seongdong-gu, Seoul- 133 791 (Korea, Republic of); Kumar, R. Saravana [R and D Department of Physics, Kongunadu Arts and Science College, Coimbatore 641 029, Tamilnadu (India); Jung, June Hyuk; Cho, Woohyung [Center for Next Generation Dye-sensitized Solar Cells, WCU Program Department of Energy Engineering, Hanyang University, Seongdong-gu, Seoul- 133 791 (Korea, Republic of); Sathyamoorthy, R. [R and D Department of Physics, Kongunadu Arts and Science College, Coimbatore 641 029, Tamilnadu (India); Won, Jongok [Department of Chemistry, Sejong University, Gwangjin-gu, Seoul 143-747 (Korea, Republic of); Kang, Yong Soo, E-mail: kangys@hanyang.ac.kr [Center for Next Generation Dye-sensitized Solar Cells, WCU Program Department of Energy Engineering, Hanyang University, Seongdong-gu, Seoul- 133 791 (Korea, Republic of)

2011-09-15

Graphical abstract: -- Abstract: Highly branched, jacks-like ZnO nanorods architecture were explored as a photoanode in dye-sensitized solar cells, and their photovoltaic performance was compared with that of branch-free ZnO nanorods photoanodes. The highly branched network and large pores of the jacks-like ZnO nanorods electrodes enhances the charge transport, and electrolyte penetration. Thus, the jacks-like ZnO nanorods DSSCs render a higher conversion efficiency of {eta} = 1.82% (V{sub oc} = 0.59 V, J{sub sc} = 5.52 mA cm{sup -2}) than that of the branch-free ZnO nanorods electrodes ({eta} = 1.08%, V{sub oc} = 0.49 V, J{sub sc} = 4.02 mA cm{sup -2}). The incident photon-to-current conversion efficiency measurements reveal that the jacks-like ZnO nanorods DSSCs exhibit higher internal quantum efficiency ({approx}59.1%) than do the branch-free ZnO nanorods DSSC ({approx}52.5%). The charge transfer resistances at the ZnO/dye/electrolyte interfaces investigated using electrochemical impedance spectroscopy showed that the jacks-like ZnO nanorods DSSC had high charge transfer resistance and a slightly longer electron lifetime, thus improving the solar-cell performance.

Determining the effect of different cooking methods on the nutritional composition of salmon (Salmo salar) and chilean jack mackerel (Trachurus murphyi) fillets

Science.gov (United States)

Balladares, Pamela; Acuña, Sergio; Quevedo, Roberto; Muñoz, Ociel

2017-01-01

The effect of four cooking methods was evaluated for proximate composition, fatty acid, calcium, iron, and zinc content in salmon and Chilean jack mackerel. The moisture content of steamed salmon decreased (64.94%) compared to the control (68.05%); a significant decrease was observed in Chilean jack mackerel in all the treatments when compared to the control (75.37%). Protein content in both salmon and Chilean jack mackerel significantly increased under the different treatments while the most significant decrease in lipids was found in oven cooking and canning for salmon and microwaving for Chilean jack mackerel. Ash concentration in both salmon and Chilean jack mackerel did not reveal any significant differences. Iron and calcium content only had significant changes in steaming while zinc did not undergo any significant changes in the different treatments. Finally, no drastic changes were observed in the fatty acid profile in both salmon and Chilean jack mackerel. PMID:28686742

Determining the effect of different cooking methods on the nutritional composition of salmon (Salmo salar and chilean jack mackerel (Trachurus murphyi fillets.

Directory of Open Access Journals (Sweden)

José M Bastías

Full Text Available The effect of four cooking methods was evaluated for proximate composition, fatty acid, calcium, iron, and zinc content in salmon and Chilean jack mackerel. The moisture content of steamed salmon decreased (64.94% compared to the control (68.05%; a significant decrease was observed in Chilean jack mackerel in all the treatments when compared to the control (75.37%. Protein content in both salmon and Chilean jack mackerel significantly increased under the different treatments while the most significant decrease in lipids was found in oven cooking and canning for salmon and microwaving for Chilean jack mackerel. Ash concentration in both salmon and Chilean jack mackerel did not reveal any significant differences. Iron and calcium content only had significant changes in steaming while zinc did not undergo any significant changes in the different treatments. Finally, no drastic changes were observed in the fatty acid profile in both salmon and Chilean jack mackerel.

Validation of on-site job-built guardrails with shoring jack as supports

Directory of Open Access Journals (Sweden)

Lan, A.

2014-06-01

Full Text Available To protect themselves against fall hazards in a slab-column frame, workers use the row of shoring jacks installed at 1 m from the edge as supports for on-site built guardrails. Inspectors of the Quebec Workers Compensation Board (Commission de la santé et de la sécurité du travail (CSST have expressed concern about the safety and compliance of these on-site built guardrails with the Quebec Safety Code for the Construction Industry (S-2.1, r.4. Some workers have also inquired if the shoring jack can be used as an anchor for a travel restraint system. The present study describes how an evaluation method and a test protocol have been used to verify if guardrails built on-site, with shoring jacks as supports, are safe and comply with the requirements of S-2.1, r.4 and if the shoring jack can be used as an anchor point for a travel restraint system. The results of the study show 1 guardrails built on site with shoring jacks as supports, are safe and comply with S-2.1, r.4 and 2 shoring jacks used as supports for guardrails must not be used as an anchor for a travel restraint system.Para la protección contra el peligro de caída en altura durante la ejecución de la estructura de un edificio, los trabajadores utilizan puntales acodalados a dos forjados y situados a 1 metro del borde de forjado como apoyo de las barandillas de seguridad. Inspectores de la Quebec Workers Compensation Board (Commision de la santé et de la sécurité du travail (CSST han expresado su preocupación por la seguridad y el cumplimiento de estos sistemas de protección en la construcción conforme al Código de Seguridad de Quebec para la industria de la construcción (S-2.1, R.6. Así mismo algunos trabajadores han mostrado su inquietud sobre la utilización de los puntales como sistemas para limitar el desplazamiento. El presente estudio describe un método de evaluación y un procedimiento de ensayo que se han utilizado para verificar si las barandillas de seguridad

Structure and biomass production of one- to seven-year-old intensively cultured jack pine plantation in Wisconsin.

Science.gov (United States)

J. Zavitkovski; David H. Dawson

1978-01-01

Spacing and rotation length effects were studied for 7 years in intensively cultured jack pine stands. Production culminated at age 5 in the densest planting and progressively later in more open spacing. Biomass production was two to several times higher than in jack pine plantations grown under traditional silvicultural systems.

Historical wildlife dynamics on Dugway Proving Ground: population and disease trends in jack rabbits over two decades. [Lepus californicus

Energy Technology Data Exchange (ETDEWEB)

Eberhardt, L.E.; Van Voris, P.

1986-08-01

In an effort to determine whether US Army activities on the Dugway Proving Ground (DPG) have had an impact on resident wildlife, intensive studies have been conducted on the biology and ecology of the black-tailed jack rabbit (Lepus californicus) since 1965. in addition, the incidence of endemic diseases in several species of resident wildlife on the DPG have been studied from the late 1950s through the mid-1970s. The objectives of this report are to: (1) compile and summarize the jack rabbit data and some of the disease information that is presently contained only in annual reports; (2) compare the DPG jack rabbit data to data available on other jack rabbit populations; and (3) analyze the data for unusual or unexplained fluctuations in population densities or in incidence of disease.

The Authority and Charismas of Jack Ma's Leadership

Institute of Scientific and Technical Information of China (English)

陈希

2014-01-01

Jack Ma is the top manager of Ali Baba group, with a strong leadership. He mixes autocratic leadership and charismatic leadership together. The powers he used are from his position, the reward system of the company and the charismas to gain his leading power. In addition, he uses his charismas and his achievements to win the trust of the employees, which develop his leadership.

Hinge(ga) Brand - tõhusaim relv mõrtsukate ja varaste vastu / Hinge Brand ; interv. Kaarel Kressa

Index Scriptorium Estoniae

Brand, Hinge, 1940-2007

2006-01-01

Intervjuu 40 aastat prokuröriametit pidanud ja pensionile siirduva Hinge Brandiga. Lisatud: Hinge Brandi CV ning Põhja ringkonnaprokuratuuri erisasjade prokuröri Jüri Kasesalu, siseministeeriumi arendusjuhi Lauri Taburi ja keskkriminaalpolitsei politseijuhtivinspektori Margus Maasepa kommentaarid

Aeg on mõtteviisi muuta / Kaie Holm

Index Scriptorium Estoniae

Holm, Kaie, 1967-

2014-01-01

Kaie Holmi ettekanne raamatukoguhoidjate X kongressil tõi palju vastukaja, autor arendab edasi mõtet, et pensioniealised raamatukoguhoidjad peaksid ise ja vabatahtlikult pensionile jääma, siis oleks noortel, kuhu tööle tulla

Variation of Time Domain Failure Probabilities of Jack-up with Wave Return Periods

Science.gov (United States)

Idris, Ahmad; Harahap, Indra S. H.; Ali, Montassir Osman Ahmed

2018-04-01

This study evaluated failure probabilities of jack up units on the framework of time dependent reliability analysis using uncertainty from different sea states representing different return period of the design wave. Surface elevation for each sea state was represented by Karhunen-Loeve expansion method using the eigenfunctions of prolate spheroidal wave functions in order to obtain the wave load. The stochastic wave load was propagated on a simplified jack up model developed in commercial software to obtain the structural response due to the wave loading. Analysis of the stochastic response to determine the failure probability in excessive deck displacement in the framework of time dependent reliability analysis was performed by developing Matlab codes in a personal computer. Results from the study indicated that the failure probability increases with increase in the severity of the sea state representing a longer return period. Although the results obtained are in agreement with the results of a study of similar jack up model using time independent method at higher values of maximum allowable deck displacement, it is in contrast at lower values of the criteria where the study reported that failure probability decreases with increase in the severity of the sea state.

Population structure of a lodgepole pine (Pinus contorta) and jack pine (P. banksiana) complex as revealed by random amplified polymorphic DNA.

Science.gov (United States)

Ye, Terrance Z; Yang, Rong-Cai; Yeh, Francis C

2002-06-01

We studied the population structure of a lodgepole (Pinus contorta Dougl.) and jack pine (Pinus banksiana Lamb.) complex in west central Alberta and neighboring areas by assessing random amplified polymorphic DNA (RAPD) variability in 23 lodgepole pine, 9 jack pine, and 8 putative hybrid populations. Of 200 random primers screened, 10 that amplified 39 sharp and reproducible RAPDs were chosen for the study. None of the 39 RAPDs were unique to the parental species. RAPD diversity ranged from 0.085 to 0.190 among populations and averaged 0.143 for lodgepole pine, 0.156 for jack pine, 0.152 for hybrids, and 0.148 for all 40 populations. The estimated population differentiation based on G(ST) was 0.168 for hybrids, 0.162 for lodgepole pine, 0.155 for jack pine, and 0.247 across all 40 populations. Cluster analysis of genetic distances generally separated jack pine from lodgepole pine and hybrids, but no division could be identified that further separated lodgepole pine from hybrids. The observed weak to mild trend of "introgression by distance" in the complex and neighbouring areas was consistent with the view that introgressive hybridization between lodgepole and jack pines within and outside the hybrid zone may have been through secondary contact and primary intergradation, respectively.

JackIn Head: Immersive Visual Telepresence System with Omnidirectional Wearable Camera.

Science.gov (United States)

Kasahara, Shunichi; Nagai, Shohei; Rekimoto, Jun

2017-03-01

Sharing one's own immersive experience over the Internet is one of the ultimate goals of telepresence technology. In this paper, we present JackIn Head, a visual telepresence system featuring an omnidirectional wearable camera with image motion stabilization. Spherical omnidirectional video footage taken around the head of a local user is stabilized and then broadcast to others, allowing remote users to explore the immersive visual environment independently of the local user's head direction. We describe the system design of JackIn Head and report the evaluation results of real-time image stabilization and alleviation of cybersickness. Then, through an exploratory observation study, we investigate how individuals can remotely interact, communicate with, and assist each other with our system. We report our observation and analysis of inter-personal communication, demonstrating the effectiveness of our system in augmenting remote collaboration.

"Delays and Vexation": Jack London and the Russo-Japanese War.

Science.gov (United States)

Sweeney, Michael S.

1998-01-01

Contributes to scholarship on journalism history and censorship by discussing Jack London's efforts as a war correspondent to cover the Russo-Japanese War in Korea and Manchuria in 1904. Focuses on the difficulties he encountered as a result of systematic and highly restrictive censorship by the Japanese. (SR)

TOPOLOGICAL STRUCTURE AND MOBILITY OF THE MECHANISMS USED IN CAR MECHANICAL JACKS

Directory of Open Access Journals (Sweden)

Viorica VELIȘCU

2015-05-01

Full Text Available This paper presents a structural analysis of the mechanism of high topological type jack - screw and translator rectilinear- patina and mobility mechanism analysis using various generally applicable formulas.

The influence of musical cadence into aquatic jumping jacks kinematics.

Science.gov (United States)

Costa, Mário J; Oliveira, Cristiana; Teixeira, Genoveva; Marinho, Daniel A; Silva, António J; Barbosa, Tiago M

2011-01-01

The aim of this study was to analyze the relationships between the head-out aquatic exercise "Jumping jacks" kinematics and the musical cadence in healthy and fit subjects. Five young women, with at least one year of experience conducting head- out aquatic programs were videotaped in the frontal plane, with a pair of cameras providing a double projection (above and below the water surface). Subjects performed an incremental protocol of five bouts (120 b·min(-1), 135 b·min(-1), 150 b·min(-1), 165 b·min(-1) and 180 b·min(-1)) with 16 full cycles of the "Jumping jacks" exercise. Data processing and calculation of upper limbs' (i.e. hands), lower limbs' (i.e. feet) and center of mass' 2D linear velocity and displacement were computed with the software Ariel Performance Analysis System and applying the 2D-DLT algorithm. Subjects decreased the cycle period during the incremental protocol. Significant and negative relationships with the musical cadence were verified for the center of mass and upper limbs vertical displacement. On the other hand, for the lower limbs lateral velocity, a significant and positive relationship was observed. It is concluded that expert and fit subjects increase the lower limb's velocity to maintain the range of motion, while the upper limb's displacement is reduced to coupe the music cadence. Key pointsWhile performing the Jumping Jacks, expert and fit subjects increase their lower limbs segmental velocity to maintain the range of motion.The upper limbs displacement is reduced to maintain the music cadence.Expert and fit subjects present similar response for alternating or simultaneously head-out aquatic exercises when increasing the music cadence.

Jack Nicholson: A Reel and Real-Life Contribution to Neurosciences.

Science.gov (United States)

Tripathi, Manjul; Purkayastha, Moushumi; Rai, Ashutosh; Mukherjee, Kanchan K

2017-05-01

Though primarily considered entertainment, cinema is a mirror of society. The portrayal of neurosciences is common in cinema, but none could do it better than Jack Nicholson. We give a brief overview of his contribution to neurosciences by analyzing his acting skills. Copyright © 2016 Elsevier Inc. All rights reserved.

Cluster analysis on a sphere: Application to magnetizations from metasediments of the Jack Hills, Western Australia

Science.gov (United States)

Bono, Richard K.; Tarduno, John A.; Dare, Matthew S.; Mitra, Gautam; Cottrell, Rory D.

2018-02-01

Metasediments of the Jack Hills contain the oldest known terrestrial minerals in the form of zircons nearly 4.4 billion years old. Paleointensity data from these zircons provide evidence for a Hadean geodynamo as old as 4.2 billion years old. Given the importance of these zircons for constraining the earliest history of the core, it is vital to understand the fidelity of the zircon record. A fundamental aspect providing context for the preservation of primary magnetic signals is the nature of overprints predicted to have been imparted on rocks of the Jack Hills due to Archean to Proterozoic metamorphic events. To be viable magnetic records of a Hadean geodynamo, zircon magnetization directions should differ from these secondary magnetizations. To evaluate these secondary magnetizations, we report paleomagnetic analyses of a comprehensive sampling of 68 quartzite cobble-sized clasts from the Jack Hills metasediments ∼0.5 to 1.0 km from the Discovery Site (which has yielded the oldest zircons and paleofield estimates). While application of standard paleomagnetic tests suggests that the ensemble of cobble directions cannot be distinguished from those drawn from a random distribution, a new cluster analysis of directions on a sphere and non-parametric resampling approaches reveal significant directions amongst subsets of the data. One, isolated at the lowest temperature analyzed [200 to 300 °C, Declination (Dec.) = 316.8°, Inclination (Inc.) = - 51.1 °] appears to be dominated by the present day field. Another, isolated at higher (but still relatively low unblocking temperatures that we call "intermediate", of ∼350-500 °C, Dec. = 243.8°, Inc. = 9.5°) agrees with a magnetic overprint isolated from the secondary Cr-Fe mica fuchsite isolated from the Jack Hills Discovery site, passing a field test at the 80% confidence level. No evidence is found in our data, or in the data of others collected on similar Jack Hills lithologies, for a widespread 1 Ga

The effect of water limitation on volatile emission, tree defense response, and brood success of Dendroctonus ponderosae in two pine hosts, lodgepole and jack pine

Directory of Open Access Journals (Sweden)

Inka eLusebrink

2016-02-01

Full Text Available The mountain pine beetle (MPB; Dendroctonus ponderosae has recently expanded its range from lodgepole pine forest into the lodgepole × jack pine hybrid zone in central Alberta, within which it has attacked pure jack pine. This study tested the effects of water limitation on tree defense response of mature lodgepole and jack pine (Pinus contorta and Pinus banksiana trees in the field. Tree defense response was initiated by inoculation of trees with the MPB-associated fungus Grosmannia clavigera and measured through monoterpene emission from tree boles and concentration of defensive compounds in phloem, needles, and necrotic tissues. Lodgepole pine generally emitted higher amounts of monoterpenes than jack pine; particularly from fungal-inoculated trees. Compared to non-inoculated trees, fungal inoculation increased monoterpene emission in both species, whereas water treatment had no effect on monoterpene emission. The phloem of both pine species contains (--α-pinene, the precursor of the beetle’s aggregation pheromone, however lodgepole pine contains two times as much as jack pine. The concentration of defensive compounds was 70-fold greater in the lesion tissue in jack pine, but only 10-fold in lodgepole pine compared to healthy phloem tissue in each species, respectively. Water-deficit treatment inhibited an increase of L-limonene as response to fungal inoculation in lodgepole pine phloem. The amount of myrcene in jack pine phloem was higher in water-deficit trees compared to ambient trees. Beetles reared in jack pine were not affected by either water or biological treatment, whereas beetles reared in lodgepole pine benefited from fungal inoculation by producing larger and heavier female offspring. Female beetles that emerged from jack pine bolts contained more fat than those that emerged from lodgepole pine, even though lodgepole pine phloem had a higher nitrogen content than jack pine phloem. These results suggest that jack pine chemistry

IDENTIFIKASI METABOLIT SEKUNDER DAN AKTIVITAS ANTIBAKTERI EKSTRAK DAUN SUNGKAI (Peronema canescens JACK. TERHADAP BEBERAPA BAKTERI PATOGEN

Directory of Open Access Journals (Sweden)

Arsyik Ibrahim

2012-12-01

Full Text Available A research which identification of secondary metabolites and antibacterial activity test from methanol exstract of leaf Sungkai (Peronema canencens Jack to several pathogens bacterial, which aims to identification of secondary methabolites and determine the antibacterial activity from crude methanol extract of leaf Sungkai (P. canencens Jack. against Streptococcus mutans, Salmonella thyposa, Bacillus subtilis and Staphylococcus aureus bacteria. Material test obtained by maceration with methanol, then tested for activity. Minimum Inhibition Concentration (MIC value extract was determined by liquid dilution and the followed by scratches on solid media method.  Minimum Kill Concentration (KBM value extracts was determined by agar diffusion method with using paper disks.The results secondary metabolite identify form extracts of leaves P. canencens obtainable derived alkaloid, terpenoids - steroids, flavonoids, and tannin compounds. Methanol extract have the antibacterial activity. Minimum Inhibition Concentration (MIC value of extract is concentration of 20% for bacteria S. mutans, S.thiposa and S.aureus, while for the B. subtilis is konsentration of 15%. Minimum Kill Concentration (KBM values exstract at a concentration of 5% effective at killing S. mutans and S. thyposa bacteria, while the concentration of 1% effective to bacteria B.subtilis and S.aureus. Key words: P. canencens Jack,  antibacteria activity, S. mutans, S. thiposa, B. subtillis, S. aureus   ABSTRAK   Telah dilakukan penelitian identifikasi metabolit sekunder dan aktivitas antibakteri ekstrak metanol daun Sungkai (P.canencens Jack terhadap beberapa bakteri patogen. Penelitian ini bertujuan untuk mengidentifikasi metabolit sekunder dan mengetahui aktifitas antibakteri dan Kadar Hambat Minimum (KHM dan Nilai Kadar Bunuh Minimum (KBM ekstrak kasar metanol daun Sungkai (P.canencens Jack. terhadap bakteri  Streptococcus mutans, Salmonella thyposa, Bacillus subtilis dan �

Soil loss by water erosion in areas under maize and jack beans intercropped and monocultures

Directory of Open Access Journals (Sweden)

Pedro Luiz Terra Lima

2014-04-01

Full Text Available Adequate soil management can create favorable conditions to reduce erosion and water runoff, consequently increase water soil recharge. Among management systems intercropping is highly used, especially for medium and small farmers. It is a system where two or more crops with different architectures and vegetative cycles are explored simultaneously at the same location. This research investigated the effects of maize intercropped with jack bean on soil losses due to water erosion, estimate C factor of Universal Soil Losses Equation (USLE and how it can be affected by soil coverage. The results obtained also contribute to database generation, important to model and estimate soil erosion. Total soil loss by erosion caused by natural rain, at Lavras, Minas Gerais, Brazil, were: 4.20, 1.86, 1.38 and 1.14 Mg ha-1, respectively, for bare soil, maize, jack bean and the intercropping of both species, during evaluated period. Values of C factor of USLE were: 0.039, 0.054 and 0.077 Mg ha Mg-1 ha-1 for maize, jack bean and intercropping between both crops, respectively. Maize presented lower vegetation cover index, followed by jack beans and consortium of the studied species. Intercropping between species showed greater potential on soil erosion control, since its cultivation resulted in lower soil losses than single crops cultivation, and this aspect is really important for small and medium farmers in the studied region.

Comparison of lodgepole and jack pine resin chemistry: implications for range expansion by the mountain pine beetle, Dendroctonus ponderosae (Coleoptera: Curculionidae

Directory of Open Access Journals (Sweden)

Erin L. Clark

2014-02-01

Full Text Available The mountain pine beetle, Dendroctonus ponderosae, is a significant pest of lodgepole pine in British Columbia (BC, where it has recently reached an unprecedented outbreak level. Although it is native to western North America, the beetle can now be viewed as a native invasive because for the first time in recorded history it has begun to reproduce in native jack pine stands within the North American boreal forest. The ability of jack pine trees to defend themselves against mass attack and their suitability for brood success will play a major role in the success of this insect in a putatively new geographic range and host. Lodgepole and jack pine were sampled along a transect extending from the beetle’s historic range (central BC to the newly invaded area east of the Rocky Mountains in north-central Alberta (AB in Canada for constitutive phloem resin terpene levels. In addition, two populations of lodgepole pine (BC and one population of jack pine (AB were sampled for levels of induced phloem terpenes. Phloem resin terpenes were identified and quantified using gas chromatography. Significant differences were found in constitutive levels of terpenes between the two species of pine. Constitutive α-pinene levels – a precursor in the biosynthesis of components of the aggregation and antiaggregation pheromones of mountain pine beetle – were significantly higher in jack pine. However, lower constitutive levels of compounds known to be toxic to bark beetles, e.g., 3-carene, in jack pine suggests that this species could be poorly defended. Differences in wounding-induced responses for phloem accumulation of five major terpenes were found between the two populations of lodgepole pine and between lodgepole and jack pine. The mountain pine beetle will face a different constitutive and induced phloem resin terpene environment when locating and colonizing jack pine in its new geographic range, and this may play a significant role in the ability of the

Comparison of lodgepole and jack pine resin chemistry: implications for range expansion by the mountain pine beetle, Dendroctonus ponderosae (Coleoptera: Curculionidae).

Science.gov (United States)

Clark, Erin L; Pitt, Caitlin; Carroll, Allan L; Lindgren, B Staffan; Huber, Dezene P W

2014-01-01

The mountain pine beetle, Dendroctonus ponderosae, is a significant pest of lodgepole pine in British Columbia (BC), where it has recently reached an unprecedented outbreak level. Although it is native to western North America, the beetle can now be viewed as a native invasive because for the first time in recorded history it has begun to reproduce in native jack pine stands within the North American boreal forest. The ability of jack pine trees to defend themselves against mass attack and their suitability for brood success will play a major role in the success of this insect in a putatively new geographic range and host. Lodgepole and jack pine were sampled along a transect extending from the beetle's historic range (central BC) to the newly invaded area east of the Rocky Mountains in north-central Alberta (AB) in Canada for constitutive phloem resin terpene levels. In addition, two populations of lodgepole pine (BC) and one population of jack pine (AB) were sampled for levels of induced phloem terpenes. Phloem resin terpenes were identified and quantified using gas chromatography. Significant differences were found in constitutive levels of terpenes between the two species of pine. Constitutive α-pinene levels - a precursor in the biosynthesis of components of the aggregation and antiaggregation pheromones of mountain pine beetle - were significantly higher in jack pine. However, lower constitutive levels of compounds known to be toxic to bark beetles, e.g., 3-carene, in jack pine suggests that this species could be poorly defended. Differences in wounding-induced responses for phloem accumulation of five major terpenes were found between the two populations of lodgepole pine and between lodgepole and jack pine. The mountain pine beetle will face a different constitutive and induced phloem resin terpene environment when locating and colonizing jack pine in its new geographic range, and this may play a significant role in the ability of the insect to persist in

Heritability and intertrait correlations in breeding subpopulations of jack pine

Science.gov (United States)

Don E. Riemenschneider

1985-01-01

Twenty breeding populations of jack pine were established in 1979 and 1980 in Minnesota, Wisconsin, and Michigan. Four populations were index populations and were each established at 4 locations by research cooperators. Sixteen populations were applied breeding populations and were established at single locations by public and private cooperators. Combined analysis of...

Survey of foliar monoterpenes across the range of jack pine reveal three widespread chemotypes: implications to host expansion of invasive mountain pine beetle

Directory of Open Access Journals (Sweden)

Spencer eTaft

2015-05-01

Full Text Available The secondary compounds of pines (Pinus can strongly affect the physiology, ecology and behaviors of the bark beetles (Coleoptera: Curculionidae, Scolytinae that feed on sub-cortical tissues of hosts. Jack pine (Pinus banksiana has a wide natural distribution range in North America (Canada and USA and thus variations in its secondary compounds, particularly monoterpenes, could affect the host expansion of invasive mountain pine beetle (Dendroctonus ponderosae, which has recently expanded its range into the novel jack pine boreal forest. We investigated monoterpene composition of 601 jack pine trees from natural and provenance forest stands representing 63 populations from Alberta to the Atlantic coast. Throughout its range, jack pine exhibited three chemotypes characterized by high proportions of α-pinene, β-pinene, or limonene. The frequency with which the α-pinene and β-pinene chemotypes occurred at individual sites was correlated to climatic variables, such as continentality and mean annual precipitation, as were the individual α-pinene and β-pinene concentrations. However, other monoterpenes were generally not correlated to climatic variables or geographic distribution. Finally, while the enantiomeric ratios of β-pinene and limonene remained constant across jack pine’s distribution, (‒:(+-α-pinene exhibited two separate trends, thereby delineating two α-pinene phenotypes, both of which occurred across jack pine’s range. These significant variations in jack pine monoterpene composition may have cascading effects on the continued eastward spread and success of D. ponderosae in the Canadian boreal forest.

Movable chain jacks and winches: case study of PETROBRAS' P58/)62and ENI's Goliat

Energy Technology Data Exchange (ETDEWEB)

Grindheim, Reidar [Aker Pusnes AS, Arendal (Norway)

2012-07-01

Recently, Aker Solutions delivered a movable chain jack system to PETROBRAS's P58/P62 FPSOs and a movable windlass system to ENI's Goliat FPSO. This paper highlights the main differences between the two systems and when it is beneficial to employ movable systems. There are many parameters to consider in determining which system to use - also a traditional system involving a single winch or chain jack per mooring line may in many cases be preferred. The movable chain jack concept is designed to operate multiple mooring lines within the same cluster. A single chain jack is lifted by a skidding gantry and moved to the next mooring line and so forth. Installation and messenger chains are moved using a large sliding chain locker allowing for later offloading of the surplus chain. The movable windlass system is also designed to operate multiple mooring lines within the same cluster. However, in this case the winch is rotary and can operate via electric or hydraulic power. One of the main considerations is to move the windlass and keep the mooring lines intact without cutting them. (author)

Healing of the Acutely Injured Anterior Cruciate Ligament: Functional Treatment with the ACL-Jack, a Dynamic Posterior Drawer Brace

Directory of Open Access Journals (Sweden)

Matthias Jacobi

2016-01-01

Full Text Available Background. The injured anterior cruciate ligament (ACL has a limited healing capacity leading to persisting instability. Hypothesis/Purpose. To study if the application of a brace, producing a dynamic posterior drawer force, after acute ACL injury reduces initial instability. Study Design. Cohort study. Methods. Patients treated with the ACL-Jack brace were compared to controls treated with primary ACL reconstruction und controls treated nonsurgically with functional rehabilitation. Measurements included anterior laxity (Rolimeter, clinical scores (Lysholm, Tegner, and IKDC, and MRI evaluation. Patients were followed up to 24 months. Results. Patients treated with the ACL-Jack brace showed a significant improvement of anterior knee laxity comparable to patients treated with ACL reconstruction, whereas laxity persisted after nonsurgical functional rehabilitation. The failure risk (secondary reconstruction necessary of the ACL-Jack group was however 21% (18 of 86 within 24 months. Clinical scores were similar in all treatment groups. Conclusion. Treatment of acute ACL tears with the ACL-Jack brace leads to improved anterior knee laxity compared to nonsurgical treatment with functional rehabilitation.

Pivoting output unit control systems activated by jacks. [for controlling aircraft flaps

Science.gov (United States)

Belliere, P.

1978-01-01

An invention to be used for controlling aircraft flaps is described. It is applicable to control systems with two coaxial output units which pivot simultaneously with respect to two fixed units and which are activated by two opposed, straight coaxial jacks.

Jack Mezirow's Conceptualisation of Adult Transformative Learning: A Review

Science.gov (United States)

Calleja, Colin

2014-01-01

This paper traces the evolution of Jack Mezirow's transformative learning theory and its conceptualisation. It discusses the three major influences, namely Thomas Khun's philosophical conception of paradigm, Freire's conception of conscientisation and consciousness growth, and Habermas' domains of learning and the discussion of…

Forest Modeling of Jack Pine Trees for BOREAS

Science.gov (United States)

Moghhadam, Mahta; Saatchi, Sasan

1994-01-01

As a part of the intensive field campaign for the Boreal forest ecosystem-atmosphere research (BOREAS) project in August 1993, the NASA/JPL AIRSAR covered an area of about 100 km by 100 km near the Prince Albert National Park in Saskatchewan, Canada. At the same time, ground-truth measurements were made in several stands which have been selected as the primary study sites, as well as in some auxiliary sites. This paper focuses on an area including Jack Pine stands in the Nipawin area near the park.

Development and simulation of the air-jack for emergency like a huge disaster; Kyujoyo eajakki no kaihatsu to sono simyureshon

Energy Technology Data Exchange (ETDEWEB)

Katsuyama, Kunihisa.; Ogata, Yuji.; Wada, Yuji. [National Institute for Resources and Environment, Tsukuba (Japan); Hashizume, Kiyoshi.; Nishida, Kenjiro. [Nippon Kayaku Corp., Tokyo (Japan)

1999-02-28

When a disaster is so huge like Kobe earthquake, every energy line is killed. Even if we want to help the sufferers, we have no energy to move machines to help them. As collapsed houses are very heavy, we need machines to remove collapsed stuff. Explosives include a lot of energy in themselves. So, an air-jack which has explosives inside was developed to remove collapsed stuff on suffered people. A simple air-jack was made and tested. One concrete block, 50cm x 50cm x 50cm, was lifted by the simple air-jack. A simulation of lifting the concrete block was carried out with a programme ANSYS on the super computer. (author)

Effect of slaughter methods on the quality of Chilean jack mackerel (Trachurus murphyi) during refrigerated storage.

Science.gov (United States)

Lyu, Fei; Huang, Rui-Ji; Liu, Lin; Zhou, Xuxia; Ding, Yu-Ting

2015-03-01

The main objective of this study was to assess the influence of slaughter methods on the quality of Chilean jack mackerel (Trachurus murphyi) during refrigerated storage on board. Fishes were slaughtered by asphyxia in air (AA), asphyxia in ice water (AI) or stunning fish heads (SH), and the rigor mortis, pH, total volatile basic nitrogen (TVB-N), trimethylamine (TMA), 2-thiobarbituric acid reactive substances (TBARS) and sensory properties for the fishes were analyzed. On day 0, Chilean jack mackerel samples of AI group displayed higher pH values than those of AA and SH groups. TVB-N, TMA and TBARS values of all samples increased with the storage time, and these values of AI had a lower increase than AA and SH. Moreover, samples of AI had a better sensory score than AA and SH during storage. It can be concluded that slaughter method of asphyxia in ice water for Chilean jack mackerel exhibit the better efficiency on maintaining the fish quality during refrigerated storage on board.

Asymptotic theory of generalized estimating equations based on jack-knife pseudo-observations

DEFF Research Database (Denmark)

Overgaard, Morten; Parner, Erik Thorlund; Pedersen, Jan

2017-01-01

A general asymptotic theory of estimates from estimating functions based on jack-knife pseudo-observations is established by requiring that the underlying estimator can be expressed as a smooth functional of the empirical distribution. Using results in p-variation norms, the theory is applied...

Jacks-of-all-trades? The effect of balanced skills on team performance

NARCIS (Netherlands)

Rosendahl Huber, L.; Sloof, R.; van Praag, M.

2014-01-01

Previous empirical studies have shown that solo entrepreneurs benefit from having balanced skills: Jacks-of-All-Trades (JATs) are better entrepreneurs than specialists are. Nowadays however, the majority of entrepreneurs start up and run ventures together in teams. In this paper we test whether the

Inflatable Indian travel pillow as a pneumatic patient jack

Directory of Open Access Journals (Sweden)

Gopalakrishna A

2006-01-01

Full Text Available The Indian travel pillow readily available in the market has been utilized as a patient jack in the operation theatre. This has been used to raise the shoulders of an anaesthetized patient for surgery in the head and neck region and a set of two pillows have been used to prop-up a prone anaesthetized patient. This allows smooth positioning of the patient after intubation without disturbance to the airway with minimal manpower.

Cross-Reactivity of Polyclonal Antibodies against Canavalia ensiformis (Jack Bean) Urease and Helicobacter pylori Urease Subunit A Fragments.

Science.gov (United States)

Kaminski, Zbigniew Jerzy; Relich, Inga; Konieczna, Iwona; Kaca, Wieslaw; Kolesinska, Beata

2018-01-01

Overlapping decapeptide fragments of H. pylori urease subunit A (UreA) were synthesized and tested with polyclonal antibodies against Canavalia ensiformis (Jack bean) urease. The linear epitopes of UreA identified using the dot blot method were then examined using epitope mapping. For this purpose, series of overlapping fragments of UreA, frameshifted ± four amino acid residues were synthesized. Most of the UreA epitopes which reacted with the Jack bean urease polyclonal antibodies had been recognized in previous studies by monoclonal antibodies against H. pylori urease. Fragments 11 - 24, 21 - 33, and 31 - 42 were able to interact with the Jack bean urease antibodies, giving stable immunological complexes. However, the lack of recognition by these antibodies of all the components in the peptide map strongly suggests that a non-continuous (nonlinear) epitope is located on the N-terminal domain of UreA. © 2018 Wiley-VHCA AG, Zurich, Switzerland.

Height and seasonal growth pattern of jack pine full-sib families

Science.gov (United States)

Don E. Riemenschneider

1981-01-01

Total tree height, seasonal shoot elongation, dates of growth initiation and cessation, and mean daily growth rate were measured and analyzed for a population of jack pine full-sib families derived from inter-provenance crosses. Parental provenance had no effect on these variables although this may have been due to small sample size. Progenies differed significantly...

Effects of geochemical composition on neutron die-away measurements: Implications for Mars Science Laboratory's Dynamic Albedo of Neutrons experiment

Energy Technology Data Exchange (ETDEWEB)

Hardgrove, C., E-mail: craig.hardgrove@stonybrook.edu [Department of Earth and Planetary Science, University of Tennessee, Knoxville, TN (United States); Moersch, J.; Drake, D. [Techsource, Santa Fe, NM (United States)

2011-12-11

The Dynamic Albedo of Neutrons (DAN) experiment, part of the scientific payload of the Mars Science Laboratory (MSL) rover mission, will have the ability to assess both the abundance and the burial depth of subsurface hydrogen as the rover traverses the Martian surface. DAN will employ a method of measuring neutron fluxes called 'neutron die-away' that has not been used in previous planetary exploration missions. This method requires the use of a pulsed neutron generator that supplements neutrons produced via spallation in the subsurface by the cosmic ray background. It is well established in neutron remote sensing that low-energy (thermal) neutrons are sensitive not only to hydrogen content, but also to the macroscopic absorption cross-section of near-surface materials. To better understand the results that will be forthcoming from DAN, we model the effects of varying abundances of high absorption cross-section elements that are likely to be found on the Martian surface (Cl, Fe) on neutron die-away measurements made from a rover platform. Previously, the Mars Exploration Rovers (MER) Spirit and Opportunity found that elevated abundances of these two elements are commonly associated with locales that have experienced some form of aqueous activity in the past, even though hydrogen-rich materials are not necessarily still present. By modeling a suite of H and Cl compositions, we demonstrate that (for abundance ranges reasonable for Mars) both the elements will significantly affect DAN thermal neutron count rates. Additionally, we show that the timing of thermal neutron arrivals at the detector can be used together with the thermal neutron count rates to independently determine the abundances of hydrogen and high neutron absorption cross-section elements (the most important being Cl). Epithermal neutron die-away curves may also be used to separate these two components. We model neutron scattering in actual Martian compositions that were determined by the MER

Impacts of fiber orientation and milling on observed crystallinity in jack pine

Science.gov (United States)

Umesh P. Agarwal; Sally A. Ralph; Richard S. Reiner; Roderquita K. Moore; Carlos Baez

2014-01-01

Influences of fiber orientation and milling on wood cellulose crystallinity were studied using jack pine wood. The fiber orientation effects were measured by sampling rectangular wood blocks in radial, tangential, and cross-sectional orientations. The influence of milling was studied by analyzing the unsieved and sieved milled wood fractions (all

The Effect of Water Limitation on Volatile Emission, Tree Defense Response, and Brood Success of Dendroctonus ponderosae in Two Pine Hosts, Lodgepole, and Jack Pine

OpenAIRE

Lusebrink, Inka; Erbilgin, Nadir; Evenden, Maya L.

2016-01-01

The mountain pine beetle (MPB; Dendroctonus ponderosae) has recently expanded its range from lodgepole pine forest into the lodgepole × jack pine hybrid zone in central Alberta, within which it has attacked pure jack pine. This study tested the effects of water limitation on tree defense response of mature lodgepole and jack pine (Pinus contorta and Pinus banksiana) trees in the field. Tree defense response was initiated by inoculation of trees with the MPB-associated fungus Grosmannia clavig...

Constituents of the essential oils of Cinnamomum parthenoxylon (Jack) Nees from Vietnam

NARCIS (Netherlands)

Dung, N.X.; Moi, La Dinh; Hung, N.D.; Leclercq, P.A.

1995-01-01

The essential oils obtained by steam distillation of the root bark and wood of Cinnamomum parthenoxylon (Jack) Nees growing wild in Vietnam were investigated by a combination of GC and GC/MS. More than 30 compounds in the root bark oil, and about 20 components in the wood oil have been identified.

Influence of mycorrhizal associations on paper birch and jack pine seedlings when exposed to elevated copper, nickel or aluminium

Energy Technology Data Exchange (ETDEWEB)

Jones, M.D.; Browning, M.H.R.; Hutchinson, T.C.

1986-10-01

Acid deposition may adversely affect northern forest ecosystems by increasing the concentration of metals in the soil solution. This study investigates the effects of ectomycorrhizal fungi on paper birch and jack pine seedlings exposed to elevated Cu, Ni or Al in sand culture. One of four mycorrhizal fungi, Scleroderma flavidum, was able to reduce Ni toxicity to the birch seedlings. It did this by reducing transport of Ni to the stems. None of the fungi affected Cu toxicity in birch. In separate experiments, jack pine seedlings were exposed to combinations of Al and Ca. Infection with Rhizopogon rubescens increased seedling susceptibility to Al. Seedlings inoculated with Suillus tomentosus showed a greater growth stimulation by Ca than uninoculated jack pines. Thus, for both tree species, the mycorrhizal association could alter the response of seedlings to high concentrations of certain metals, although this varied with fungal species. 8 references.

Mosaic Stunting in jack pine seedlings in a northern Michigan bareroot nursery

Science.gov (United States)

Lynette Potvin; R. Kasten Dumroese; Martin F. Jurgensen; Dana Richter

2010-01-01

Mosaic, or patchy, stunting of bareroot conifer seedlings is thought to be caused by deficiencies of mycorrhizal fungi following fumigation, resulting in reduced nutrient uptake, particularly phosphorus. Mosaic stunting of jack pine (Pinus banksiana) seedlings was observed in 2005 at the USDA Forest Service JW Toumey Nursery in Watersmeet, MI. We initiated a study to...

Rereading "The Jack-Roller:" Hidden Histories in Sociology and Social Work

Science.gov (United States)

Shaw, Ian

2009-01-01

I revisit one of the iconic Chicago School studies, Clifford Shaw's "The Jack-Roller". A naive reading of Shaw's book leaves the reader with a sense of having been inducted into a melange of what we now know as "sociology" and "social work," but which to Shaw seems a coherent stance. I suggest that this is close to the heart of how things were,…

POPULASI DAN HABITAT Nepenthes ampullaria Jack. DI CAGAR ALAM MANDOR, KALIMANTAN BARAT

Directory of Open Access Journals (Sweden)

Maysarah .

2017-04-01

Full Text Available Nepenthes ampullaria Jack. is a species which adapted on the nutrient-poor areas in Mandor nature reserve.  Its could be increasing the quality of Mandor nature reserve as protected area. This research aims to study the population and habitat of N. ampullaria in the Mandor nature reserve. This study was conducted at two habitats, heath forest and peat swamp forest. Observations were made on, population abundance and habitat factors of  N. ampullaria. The results showed that the highest population density of N. ampullaria was in heath forest. Their are growth in groups. Vegetation analysis showed that constituent species habitat of N. ampullaria consist of 69 species from 39 familly. Result of identification to insects showed Formicidae is dominant family that trapped in pitcher of N. ampullaria. Temperature and humidity in N. ampullaria’s habitat has been switable for requirements growth of pitcher plant. Rainfall during the study was normally. Ratio of sand and soil on both affected the improvement of individual N. ampullaria in Mandor nature reserve. Keywords: habitat, Mandor nature reserve, Nepenthes ampullaria Jack, population

Saaremaa politseijuht pensionile / Andres Sepp

Index Scriptorium Estoniae

Sepp, Andres, 1976-

2005-01-01

Kuressaare politseijaoskonna ülemkomissar Ants Ley esitas politseiametile lahkumisavalduse. Väidetavalt on nimetatud ühe võimaliku politseijuhikandidaadina Lääne prefektuuri teenistusosakonna komissari Aare Alliku nime. Lisa: Ants Ley

Characterizing the physical and genetic structure of the lodgepole pine × jack pine hybrid zone: mosaic structure and differential introgression.

Science.gov (United States)

Cullingham, Catherine I; James, Patrick M A; Cooke, Janice E K; Coltman, David W

2012-12-01

Understanding the physical and genetic structure of hybrid zones can illuminate factors affecting their formation and stability. In north-central Alberta, lodgepole pine (Pinus contorta Dougl. ex Loud. var. latifolia) and jack pine (Pinus banksiana Lamb) form a complex and poorly defined hybrid zone. Better knowledge of this zone is relevant, given the recent host expansion of mountain pine beetle into jack pine. We characterized the zone by genotyping 1998 lodgepole, jack pine, and hybrids from British Columbia, Alberta, Saskatchewan, Ontario, and Minnesota at 11 microsatellites. Using Bayesian algorithms, we calculated genetic ancestry and used this to model the relationship between species occurrence and environment. In addition, we analyzed the ancestry of hybrids to calculate the genetic contribution of lodgepole and jack pine. Finally, we measured the amount of gene flow between the pure species. We found the distribution of the pine classes is explained by environmental variables, and these distributions differ from classic distribution maps. Hybrid ancestry was biased toward lodgepole pine; however, gene flow between the two species was equal. The results of this study suggest that the hybrid zone is complex and influenced by environmental constraints. As a result of this analysis, range limits should be redefined.

Kinetics and mechanism of jack bean urease inhibition by Hg2+

Directory of Open Access Journals (Sweden)

Du Nana

2012-12-01

Full Text Available Abstract Background Jack bean urease (EC 3.5.1.5 is a metalloenzyme, which catalyzes the hydrolysis of urea to produce ammonia and carbon dioxide. The heavy metal ions are common inhibitors to control the rate of the enzymatic urea hydrolysis, which take the Hg2+ as the representative. Hg2+ affects the enzyme activity causing loss of the biological function of the enzyme, which threatens the survival of many microorganism and plants. However, inhibitory kinetics of urease by the low concentration Hg2+ has not been explored fully. In this study, the inhibitory effect of the low concentration Hg2+ on jack bean urease was investigated in order to elucidate the mechanism of Hg2+ inhibition. Results According to the kinetic parameters for the enzyme obtained from Lineweaver–Burk plot, it is shown that the Km is equal to 4.6±0.3 mM and Vm is equal to 29.8±1.7 μmol NH3/min mg. The results show that the inhibition of jack bean urease by Hg2+ at low concentration is a reversible reaction. Equilibrium constants have been determined for Hg2+ binding with the enzyme or the enzyme-substrate complexes (Ki =0.012 μM. The results show that the Hg2+ is a noncompetitive inhibitor. In addition, the kinetics of enzyme inhibition by the low concentration Hg2+ has been studied using the kinetic method of the substrate reaction. The results suggest that the enzyme first reversibly and quickly binds Hg2+ and then undergoes a slow reversible course to inactivation. Furthermore, the rate constant of the forward reactions (k+0 is much larger than the rate constant of the reverse reactions (k-0. By combining with the fact that the enzyme activity is almost completely lost at high concentration, the enzyme is completely inactivated when the Hg2+ concentration is high enough. Conclusions These results suggest that Hg2+ has great impacts on the urease activity and the established inhibition kinetics model is suitable.

Southwestern Surgical Congress Jack A. Barney award competition presenters - Where are they now?

Science.gov (United States)

Kothari, Shanu N; Kallies, Kara J

2017-12-01

Resident research presentations at surgical conferences may encourage future research endeavors. 2010-2016 SWSC annual meeting programs were reviewed for presenters eligible for the Jack Barney award. Award recipients from 1987 to 2016 were included. There were 100 unique presenters eligible for the Jack Barney award, and 28 unique award recipients. Thirty-six (82%) presenters currently practice in a community setting, 5 (11%) at a university hospital, 2 (5%) internationally, and 1 (2%) in a military hospital. Scholarly articles were published by 41% of presenters. Sixteen of the 28 recipients (57%) practice in community hospitals, and 9 (32%) practice in university settings; 3 are still in training. Twenty recipients (71%) published after residency. Thirty percent and 25% of presenters and recipients are SWSC members, respectively. Peer-reviewed publications were frequent among eligible presenters and award recipients. Encouraging presenters to become SWSC members provides an opportunity for improved retention. Copyright © 2017 Elsevier Inc. All rights reserved.

Jack-of-all-trades effects drive biodiversity–ecosystem multifunctionality relationships in European forests

Science.gov (United States)

van der Plas, Fons; Manning, Peter; Allan, Eric; Scherer-Lorenzen, Michael; Verheyen, Kris; Wirth, Christian; Zavala, Miguel A.; Hector, Andy; Ampoorter, Evy; Baeten, Lander; Barbaro, Luc; Bauhus, Jürgen; Benavides, Raquel; Benneter, Adam; Berthold, Felix; Bonal, Damien; Bouriaud, Olivier; Bruelheide, Helge; Bussotti, Filippo; Carnol, Monique; Castagneyrol, Bastien; Charbonnier, Yohan; Coomes, David; Coppi, Andrea; Bastias, Cristina C.; Muhie Dawud, Seid; De Wandeler, Hans; Domisch, Timo; Finér, Leena; Gessler, Arthur; Granier, André; Grossiord, Charlotte; Guyot, Virginie; Hättenschwiler, Stephan; Jactel, Hervé; Jaroszewicz, Bogdan; Joly, François-Xavier; Jucker, Tommaso; Koricheva, Julia; Milligan, Harriet; Müller, Sandra; Muys, Bart; Nguyen, Diem; Pollastrini, Martina; Raulund-Rasmussen, Karsten; Selvi, Federico; Stenlid, Jan; Valladares, Fernando; Vesterdal, Lars; Zielínski, Dawid; Fischer, Markus

2016-01-01

There is considerable evidence that biodiversity promotes multiple ecosystem functions (multifunctionality), thus ensuring the delivery of ecosystem services important for human well-being. However, the mechanisms underlying this relationship are poorly understood, especially in natural ecosystems. We develop a novel approach to partition biodiversity effects on multifunctionality into three mechanisms and apply this to European forest data. We show that throughout Europe, tree diversity is positively related with multifunctionality when moderate levels of functioning are required, but negatively when very high function levels are desired. For two well-known mechanisms, ‘complementarity' and ‘selection', we detect only minor effects on multifunctionality. Instead a third, so far overlooked mechanism, the ‘jack-of-all-trades' effect, caused by the averaging of individual species effects on function, drives observed patterns. Simulations demonstrate that jack-of-all-trades effects occur whenever species effects on different functions are not perfectly correlated, meaning they may contribute to diversity–multifunctionality relationships in many of the world's ecosystems. PMID:27010076

Destructive Cholangitis in an Adult Jack Russell Terrier

Directory of Open Access Journals (Sweden)

Atsushi Kodama

2012-01-01

Full Text Available A 4-year-old female Jack Russell terrier dog exhibited vomiting and severe jaundice of the visible mucous membranes and skin. Ultrasonography revealed diffuse areas of high echogenicity and focal areas of low echogenicity in the left lobe of the liver. On macroscopic observation of the biopsied liver specimen, many scattered irregularly shaped red spots were observed on the liver surface and on the cut surface. Histopathologically, there was loss of the interlobular bile duct and cholangitis accompanied by infiltration of pigment-laden macrophages in the Glisson’s capsule. Therefore, in the present case the dog was diagnosed with destructive cholangitis.

Léon Lederman, Mel Schwartz and Jack Steinberger wre awarded the 1988 Nobel Physics Prize.

CERN Multimedia

Photographic Service

1988-01-01

Léon Lederman (left), Mel Schwartz (right) and Jack Steinberger were awarded the 1988 Nobel Physics Prize for their 1962 experiment at Brookhaven which showed that neutrinos come in more than one kind.

Transcriptome resources and functional characterization of monoterpene synthases for two host species of the mountain pine beetle, lodgepole pine (Pinus contorta) and jack pine (Pinus banksiana)

Science.gov (United States)

2013-01-01

Background The mountain pine beetle (MPB, Dendroctonus ponderosae) epidemic has affected lodgepole pine (Pinus contorta) across an area of more than 18 million hectares of pine forests in western Canada, and is a threat to the boreal jack pine (Pinus banksiana) forest. Defence of pines against MPB and associated fungal pathogens, as well as other pests, involves oleoresin monoterpenes, which are biosynthesized by families of terpene synthases (TPSs). Volatile monoterpenes also serve as host recognition cues for MPB and as precursors for MPB pheromones. The genes responsible for terpene biosynthesis in jack pine and lodgepole pine were previously unknown. Results We report the generation and quality assessment of assembled transcriptome resources for lodgepole pine and jack pine using Sanger, Roche 454, and Illumina sequencing technologies. Assemblies revealed transcripts for approximately 20,000 - 30,000 genes from each species and assembly analyses led to the identification of candidate full-length prenyl transferase, TPS, and P450 genes of oleoresin biosynthesis. We cloned and functionally characterized, via expression of recombinant proteins in E. coli, nine different jack pine and eight different lodgepole pine mono-TPSs. The newly identified lodgepole pine and jack pine mono-TPSs include (+)-α-pinene synthases, (-)-α-pinene synthases, (-)-β-pinene synthases, (+)-3-carene synthases, and (-)-β-phellandrene synthases from each of the two species. Conclusion In the absence of genome sequences, transcriptome assemblies are important for defence gene discovery in lodgepole pine and jack pine, as demonstrated here for the terpenoid pathway genes. The product profiles of the functionally annotated mono-TPSs described here can account for the major monoterpene metabolites identified in lodgepole pine and jack pine. PMID:23679205

Transcriptome resources and functional characterization of monoterpene synthases for two host species of the mountain pine beetle, lodgepole pine (Pinus contorta) and jack pine (Pinus banksiana).

Science.gov (United States)

Hall, Dawn E; Yuen, Macaire M S; Jancsik, Sharon; Quesada, Alfonso Lara; Dullat, Harpreet K; Li, Maria; Henderson, Hannah; Arango-Velez, Adriana; Liao, Nancy Y; Docking, Roderick T; Chan, Simon K; Cooke, Janice Ek; Breuil, Colette; Jones, Steven Jm; Keeling, Christopher I; Bohlmann, Jörg

2013-05-16

The mountain pine beetle (MPB, Dendroctonus ponderosae) epidemic has affected lodgepole pine (Pinus contorta) across an area of more than 18 million hectares of pine forests in western Canada, and is a threat to the boreal jack pine (Pinus banksiana) forest. Defence of pines against MPB and associated fungal pathogens, as well as other pests, involves oleoresin monoterpenes, which are biosynthesized by families of terpene synthases (TPSs). Volatile monoterpenes also serve as host recognition cues for MPB and as precursors for MPB pheromones. The genes responsible for terpene biosynthesis in jack pine and lodgepole pine were previously unknown. We report the generation and quality assessment of assembled transcriptome resources for lodgepole pine and jack pine using Sanger, Roche 454, and Illumina sequencing technologies. Assemblies revealed transcripts for approximately 20,000 - 30,000 genes from each species and assembly analyses led to the identification of candidate full-length prenyl transferase, TPS, and P450 genes of oleoresin biosynthesis. We cloned and functionally characterized, via expression of recombinant proteins in E. coli, nine different jack pine and eight different lodgepole pine mono-TPSs. The newly identified lodgepole pine and jack pine mono-TPSs include (+)-α-pinene synthases, (-)-α-pinene synthases, (-)-β-pinene synthases, (+)-3-carene synthases, and (-)-β-phellandrene synthases from each of the two species. In the absence of genome sequences, transcriptome assemblies are important for defence gene discovery in lodgepole pine and jack pine, as demonstrated here for the terpenoid pathway genes. The product profiles of the functionally annotated mono-TPSs described here can account for the major monoterpene metabolites identified in lodgepole pine and jack pine.

Preliminary report and design of using Jack Pines for the phytoremediation of diesel-contaminated soils in northern Saskatchewan

International Nuclear Information System (INIS)

McLean, L.; Ireland, J.; Hohn, S.; Herman, L.; Hanna, A.

1999-01-01

A study is being conducted to evaluate the feasibility of using Jack Pines for the phytoremediation of diesel-contaminated soils in northern Saskatchewan. The sites have some level of diesel contamination from spills associated with generators belonging to SaskTel. The first phase of the study was conducted under controlled conditions in a greenhouse. Seedlings of Jack Pine were planted in sand with a range of diesel concentrations. A control planting of seedlings with no diesel was also conducted. The study also included control pots of sand with diesel and no seedlings for comparison of diesel degradation. The results from this first phase will help determine the feasibility of performing more extensive testing of phytoremediation on site in northern Saskatchewan. Results will be conclusive in August 2000. So far, the results show that Jack Pines can survive in soil highly contaminated with hydrocarbons. The second phase will include field trials. Diesel concentrations at the sites range from 0 ppm to 30,000 ppm. 4 refs., 2 tabs., 5 figs

Preliminary report and design of using Jack Pines for the phytoremediation of diesel-contaminated soils in northern Saskatchewan

Energy Technology Data Exchange (ETDEWEB)

McLean, L; Ireland, J; Hohn, S; Herman, L [ERIN Consulting Ltd., Regina, SK (Canada); Hanna, A [SaskTel, Regina, SK (Canada)

1999-01-01

A study is being conducted to evaluate the feasibility of using Jack Pines for the phytoremediation of diesel-contaminated soils in northern Saskatchewan. The sites have some level of diesel contamination from spills associated with generators belonging to SaskTel. The first phase of the study was conducted under controlled conditions in a greenhouse. Seedlings of Jack Pine were planted in sand with a range of diesel concentrations. A control planting of seedlings with no diesel was also conducted. The study also included control pots of sand with diesel and no seedlings for comparison of diesel degradation. The results from this first phase will help determine the feasibility of performing more extensive testing of phytoremediation on site in northern Saskatchewan. Results will be conclusive in August 2000. So far, the results show that Jack Pines can survive in soil highly contaminated with hydrocarbons. The second phase will include field trials. Diesel concentrations at the sites range from 0 ppm to 30,000 ppm. 4 refs., 2 tabs., 5 figs.

The characters God and Hamlet by Jack Miles

Directory of Open Access Journals (Sweden)

Tania de Fátima da Silva

2015-04-01

Full Text Available In the book “God - A Biography,” Jack Miles aims to introduce ourselves Creator-God as a literary character. Miles developed a narrative based on concept aristotelian, in other words, the structure of the work is made from beginning to end. This procedure established a harmony arising from the interaction between the parties, which contributes to scrutinize the precise details of the story of the main protagonist. We decided to highlight that time some characteristics of the main character of the work and compare them to the character Hamlet, by William Shakespeare, because from the beginning of the narrative to completion Miles calls the reader’s attention to the play Shakespeare.

A-jacks and Aquawrap installations in Utah : scour revetment performance evaluation, final report, December 2009.

Science.gov (United States)

2009-12-01

This is a performance evaluation report for A-Jacks, an articulated concrete block designed to protect bridge elements exposed to the river scouring forces, and for Aquawrap, a glass fiber reinforced polymer designed to protect and strengthen bridge ...

The construction of identity in a consumerist society: Delillo’s Jack Gladney

Directory of Open Access Journals (Sweden)

Sanja Matković

2016-02-01

Full Text Available This paper deals with the construction of the postmodern identity of Jack Gladney, the main character in Don DeLillo’s White Noise (1985. Employing (postmodern, social psychology, and psychoanalytic theories of Zygmunt Bauman, Erich Fromm, Jean Baudrillard, and Gilles Lipovetsky, it analyzes the construction of Gladney’s character through his social roles as professor, husband, and consumer in the narrow sense of the word in order to deduce that his consumerist practices have spread to all aspects of his life. This reading reveals a new interpretation of Gladney’s fear of death; it shows that Gladney’s thanatophobia represents a consequence of his atheistic worldview. Namely, unable to find a haven in religion, he unsuccessfully seeks the meaning of life and death elsewhere, mainly in consumerism, which is identified as the source of his alienation from himself, people, and God. This paper suggests that numerous problems of postmodern life are caused by the lack of faith in God and proposes a conclusion that religion itself could be the answer to the difficulties faced by postmodern individuals with fragmented identities such as Jack Gladney.

Manuka honey (Leptospermum scoparium) inhibits jack bean urease activity due to methylglyoxal and dihydroxyacetone.

Science.gov (United States)

Rückriemen, Jana; Klemm, Oliver; Henle, Thomas

2017-09-01

Manuka honey (Leptospermum scoparium) exerts a strong antibacterial effect. Bacterial enzymes are an important target for antibacterial compounds. The enzyme urease produces ammonia and enables bacteria to adapt to an acidic environment. A new enzymatic assay, based on photometric detection of ammonia with ninhydrin, was developed to study urease activity. Methylglyoxal (MGO) and its precursor dihydroxyacetone (DHA), which are naturally present in manuka honey, were identified as jack bean urease inhibitors with IC 50 values of 2.8 and 5.0mM, respectively. Urease inhibition of manuka honey correlates with its MGO and DHA content. Non-manuka honeys, which lack MGO and DHA, showed significantly less urease inhibition. MGO depletion from manuka honey with glyoxalase reduced urease inhibition. Therefore, urease inhibition by manuka honey is mainly due to MGO and DHA. The results obtained with jack bean urease as a model urease, may contribute to the understanding of bacterial inhibition by manuka honey. Copyright © 2017 Elsevier Ltd. All rights reserved.

The Cholesterol Lowering Effects of Eurycoma longifolia Jack (Tongkat Ali Root Extract in Male Rats

Directory of Open Access Journals (Sweden)

Ghasak G Faisal

2017-04-01

Full Text Available Background: To investigate the effect of Eurycoma longifolia Jack root extract on serum lipids in rats. Methods: Twenty-six mature male albino Wistar rats were used in this study. A group of 18 rats were fed a high fat and high cholesterol diet for 4 weeks, after which their lipid profile was compared to the control group, who were kept on a normal diet. The rats were then further divided into three groups, the Cf group that continued to feed on a high fat and cholesterol diet only, and group A and group B who continued on a high fat diet with the addition of 5 mg/kg and 10 mg/kg of Eurycoma longifolia Jack root extract respectively for 4 weeks. After the 4 week period, the rat's lipid profiles were analysed again. Results: Group A and B showed significant total cholesterol reduction when compared to the Cf group, 140 ± 7.23, 139.63 ± 7.95, 192.14 ± 8.96 mg/dL respectively (p < 0.001. The total cholesterol/HDL ratio in group A was 5 however there was a sharp increase in group B to a high-risk level of 9.2 indicating a significant drop in HDL levels. The LDL level increased significantly in both group A and B compared to the Cf group. Conclusions: Eurycoma longifolia Jack root extract is effective in lowering total cholesterol, however the dose needs to be adjusted to prevent an excessive decrease in HDL levels.

A sperm-agglutinating lectin from seeds of Jack fruit (Artocarpus heterophyllus).

Science.gov (United States)

Namjuntra, P; Muanwongyathi, P; Chulavatnatol, M

1985-04-30

A lectin specific for N-acetylgalactosamine was isolated from seed extract of Jack fruit (Artocarpus heterophyllus) by ammonium sulfate precipitation, followed by affinity chromatography on a Affigel-galactosamine-agarose column. The lectin possessed agglutinating activities for human and rat sperm as well as human red blood cells. It was found to have Mr = 62,000 consisting of two dissimilar subunits of Mr = 18,000 and 13,000. It also cross-reacted with an antibody against the lectin of Osage Orange (Maclura pomifera).

Jack'd, a Mobile Social Networking Application: A Site of Exclusion Within a Site of Inclusion.

Science.gov (United States)

Bartone, Michael D

2018-01-01

User-generated smartphone applications have created a new level of virtual connectivity for gay males, one in which users can create profiles and meet other users as nearby or as far away as possible. For those within close proximity, the other users can be considered their "virtual neighbors." Although the applications are theoretically designed to be places of inclusion and not exclusion, where any gay male with economic means can download an application, many profiles have been created that exclude other users. Through an examination of profiles on one such application, Jack'd, exclusion is found in the way users celebrate and reinforce ideas of traditional masculinity and denigrate and reinforce stereotypic ideas of femininity embodied by some gay men. Jack'd, and other user-generated smartphone applications, can be read as virtual neighborhoods where one is excluded based on their gender performance.

Preliminary results of the empirical validation of daily increments in otoliths of jack mackerel Trachurus symmetricus murphyi (Nichols, 1920 marked with oxytetracycline

Directory of Open Access Journals (Sweden)

Miguel Araya

2003-12-01

Full Text Available The frequency of microincrement formation in sagittae otoliths of jack mackerel Trachurus symmetricus was validated using experiments on captive fish. Adult jack mackerel were injected with a dose of 100 mg of oxytetracycline/kg of fish. A second injection was performed 30 days later. The fish were then sacrificed and their sagittae otoliths were extracted. Thin sections of the otoliths were prepared and observed through an epifluorescent microscope using ultraviolet light. Two fluorescent marks corresponding to the two injections were clearly visible. The average number of microincrements between the two fluorescent marks was 29 (n=10; S.D.=1.63 and the median was 29.3. The Wilcoxon signed-rank test indicated that this value was not significantly different from 30. This result indicates that microincrements in otoliths of adult jack mackerel of between 28.4 and 37.7 cm fork length are formed with a daily frequency.

Pandemic Fear and Literature: Observations from Jack London’s The Scarlet Plague

Centers for Disease Control (CDC) Podcasts

2014-11-18

Sarah Gregory reads an abridged version of the essay, Pandemic Fear and Literature: Observations from Jack London’s The Scarlet Plague.  Created: 11/18/2014 by National Center for Emerging and Zoonotic Infectious Diseases (NCEZID).   Date Released: 11/20/2014.

The lodgepole × jack pine hybrid zone in Alberta, Canada: a stepping stone for the mountain pine beetle on its journey East across the boreal forest?

Science.gov (United States)

Lusebrink, Inka; Erbilgin, Nadir; Evenden, Maya L

2013-09-01

Historical data show that outbreaks of the tree killing mountain pine beetle are often preceded by periods of drought. Global climate change impacts drought frequency and severity and is implicated in the range expansion of the mountain pine beetle into formerly unsuitable habitats. Its expanded range has recently reached the lodgepole × jack pine hybrid zone in central Alberta, Canada, which could act as a transition from its historical lodgepole pine host to a jack pine host present in the boreal forest. This field study tested the effects of water limitation on chemical defenses of mature trees against mountain pine beetle-associated microorganisms and on beetle brood success in lodgepole × jack pine hybrid trees. Tree chemical defenses as measured by monoterpene emission from tree boles and monoterpene concentration in needles were greater in trees that experienced water deficit compared to well-watered trees. Myrcene was identified as specific defensive compound, since it significantly increased upon inoculation with dead mountain pine beetles. Beetles reared in bolts from trees that experienced water deficit emerged with a higher fat content, demonstrating for the first time experimentally that drought conditions benefit mountain pine beetles. Further, our study demonstrated that volatile chemical emission from tree boles and phloem chemistry place the hybrid tree chemotype in-between lodgepole pine and jack pine, which might facilitate the host shift from lodgepole pine to jack pine.

Secondary vegetation succession on jack pine (Pinus banksiana) cutovers in northeastern Ontario, Canada

Energy Technology Data Exchange (ETDEWEB)

Tiveau, Daniel

2000-07-01

The effects of different harvesting and site preparation methods on competing vegetation were studied in nine jack pine (Pinus banksiana) cutovers in northeastern Ontario, Canada. Six different treatments plus glyphosate herbiciding and no herbiciding were applied: 1) tree-length harvesting followed by trenching, and full-tree harvesting followed by five site preparations, 2) no site preparation, 3) trenching and 4) blading and compaction as well as blading followed by two planting densities, 5) 1.2m and 6) 2m. Competing vegetation was assessed preharvest and years 1, 2, 3, and 5 postharvest. Data was also available from nine juvenile sites as well as nine semimature sites. Data collection consisted of coverage values of each species as well as structural data for main life forms in height classes. Growth and health data of the planted jack pine seedlings were also available. The data was analyzed using detrended correspondence analysis (DCA), diversity indices and tabular analysis. Three years after the herbicide application there is no difference between the total coverage in the halfplots that have received herbiciding and those that have not, but an alteration of the relative abundance of species groups has developed; glyphosate herbiciding promotes grasses over shrubs. When no site preparation is applied, shrubs increase and compete with the seedlings, whose growth is cut in half compared to the ones that have been site prepared by trenching. Five years after blading, and blading plus compaction, there is still very little vegetation in the research plots, but there is no reduction of the survival rate and growth of the jack pine seedlings. More dense planting after this treatment leads to more competing vegetation, probably due to increased availability of moisture. Grasses do not seem to be affected by compaction and pioneer mosses are promoted by this treatment but compaction leads to a significant reduction of the total coverage of competing vegetation

Selected Problems of Sensitivity and Reliability of a Jack-Up Platform

Directory of Open Access Journals (Sweden)

Rozmarynowski Bogdan

2018-03-01

Full Text Available The paper deals with sensitivity and reliability applications to numerical studies of an off-shore platform model. Structural parameters and sea conditions are referred to the Baltic jack-up drilling platform. The sudy aims at the influence of particular basic variables on static and dynamic response as well as the probability of failure due to water waves and wind loads. The paper presents the sensitivity approach to a generalized eigenvalue problem and evaluation of the performace functions. The first order time-invariant problems of structural reliability analysis are under concern.

Fatty Acid Composition of Novel Host Jack Pine Do Not Prevent Host Acceptance and Colonization by the Invasive Mountain Pine Beetle and Its Symbiotic Fungus

Science.gov (United States)

Ishangulyyeva, Guncha; Najar, Ahmed; Curtis, Jonathan M.

2016-01-01

Fatty acids are major components of plant lipids and can affect growth and development of insect herbivores. Despite a large literature examining the roles of fatty acids in conifers, relatively few studies have tested the effects of fatty acids on insect herbivores and their microbial symbionts. Particularly, whether fatty acids can affect the suitability of conifers for insect herbivores has never been studied before. Thus, we evaluated if composition of fatty acids impede or facilitate colonization of jack pine (Pinus banksiana) by the invasive mountain pine beetle (Dendroctonus ponderosae) and its symbiotic fungus (Grosmannia clavigera). This is the first study to examine the effects of tree fatty acids on any bark beetle species and its symbiotic fungus. In a novel bioassay, we found that plant tissues (hosts and non-host) amended with synthetic fatty acids at concentrations representative of jack pine were compatible with beetle larvae. Likewise, G. clavigera grew in media amended with lipid fractions or synthetic fatty acids at concentrations present in jack pine. In contrast, fatty acids and lipid composition of a non-host were not suitable for the beetle larvae or the fungus. Apparently, concentrations of individual, rather than total, fatty acids determined the suitability of jack pine. Furthermore, sampling of host and non-host tree species across Canada demonstrated that the composition of jack pine fatty acids was similar to the different populations of beetle’s historical hosts. These results demonstrate that fatty acids composition compatible with insect herbivores and their microbial symbionts can be important factor defining host suitability to invasive insects. PMID:27583820

3-D habitat suitability of jack mackerel Trachurus murphyi in the Southeastern Pacific, a comprehensive study

NARCIS (Netherlands)

Bertrand, A.; Habasque, J.; Hattab, Tarek; Hintzen, N.T.; Ricardo, Oliveros Ramos; Gutierrez, M.; Demarcq, Herve; Gerlotto, F.

2016-01-01

South Pacific jack mackerel, Trachurus murphyi, has an ocean-scale distribution, from the South American coastline to New Zealand and Tasmania. This fish, captured by Humans since the Holocene, is nowadays heavily exploited and its population has decreased substantially since the mid-1990s. The

Eesti saab 2018. aasta Londoni raamatumessil erilise tähelepanu osaliseks / Jacks Thomas ; intervjueerinud Priit Hõbemägi

Index Scriptorium Estoniae

Thomas, Jacks

2017-01-01

Intervjuu Euroopa ühe suurima, Londoni raamatumessi direktori Jacks Thomasiga, kes külastas Tallinna, et teha ettevalmistusi järgmiseks aastaks, kui Eesti koos teiste Baltimaadega on messi peakülaline

In Search of the Real Mr. China Jack Perkowski's positive account of his business adventures in China

Institute of Scientific and Technical Information of China (English)

MATTHEW PLOWRIGHT

2008-01-01

@@ When former Wall Street banker Jack Perkowski first arrived in Hong Kong in 1990 looking to set up a business, not only did he not speak a word of the language, he had never even tasted Chinese food.

The Jack mackerel Trachurus murphyiand the environmental macro-scale variables

Directory of Open Access Journals (Sweden)

Marco Espino

2013-10-01

Full Text Available This paper analyses information on various macro environmental variables available since 1876 for the Southeast Pacific and more recent data on Jack mackerel Trachurus murphyi (Nichols, 1920 landings and biomass in the Peruvian sea, relating them to probable areas of water masses equivalent to Cold Coastal Waters (CCW and Subtropical Surface Waters (SSW. It is concluded that the index of the Pacific Decadal Oscillation (PDO presents expressions of variability that are consistent with those found for the Southern Oscillation Index (SOI and that the detected changes in biomass of Jack mackerel T. murphyiin the Peruvian sea reflect changes in the availability of the fish stock associated with secular (SOI and decadal (PDO variability patterns. These fluctuations in stock availability impact fisheries in Ecuador, Peru and northern Chile, which show significant variations in their landings and would have given a biased picture of the state of abundance, leading to wrong diagnoses of the real situation of the exploited stocks. These patterns of variability would also affect the appearance of El Niño, making them start in the southern hemisphere autumn or spring depending on whether the current PDO is positive or negative. Periods of high (1876 – 1925 and 1976 – 2012 and low (1926 – 1975 variability are also identified in relation to the Euclidean distance of the variances of the SOI; and in relation to the PDO a distinction is made between warm (1925 – 1944 and 1975 – 1994, cold (1945 – 1974 and tempered or interface periods (1895 – 1924 and 1995 – 2012, the latter being explained by the interaction between periods of high variability.

Jack-o'-Lantern and nuclear mushrooms

International Nuclear Information System (INIS)

Charpak, G.; Garwin, R.

1997-01-01

Is the humanity survival threatened by the use of nuclear energy? Do nuclear power plants stand risks? and if the answer is yes what kind of risks? Georges Charpak, physicist, Nobel price of physics, member of Academy of Science (Paris) and Richard L. Garwin, physicist, member of National Academy of Science (Washington) bring some answers: what is the fission, what is the fusion, the neutron, the PWR reactors, the fast neutrons reactors, the three miles island accident and the Chernobyl accident, their effect on public opinion, the radiations and the living, the nuclear wastes and the becoming of nuclear weapons. (N.C.)

Pervasive remagnetization of detrital zircon host rocks in the Jack Hills, Western Australia and implications for records of the early geodynamo

Science.gov (United States)

Weiss, Benjamin P.; Maloof, Adam C.; Tailby, Nicholas; Ramezani, Jahandar; Fu, Roger R.; Hanus, Veronica; Trail, Dustin; Bruce Watson, E.; Harrison, T. Mark; Bowring, Samuel A.; Kirschvink, Joseph L.; Swanson-Hysell, Nicholas L.; Coe, Robert S.

2015-11-01

It currently is unknown when Earth's dynamo magnetic field originated. Paleomagnetic studies indicate that a field with an intensity similar to that of the present day existed 3.5 billion years ago (Ga). Detrital zircon crystals found in the Jack Hills of Western Australia are some of the very few samples known to substantially predate this time. With crystallization ages ranging from 3.0-4.38 Ga, these zircons might preserve a record of the missing first billion years of Earth's magnetic field history. However, a key unknown is the age and origin of magnetization in the Jack Hills zircons. The identification of >3.9 Ga (i.e., Hadean) field records requires first establishing that the zircons have avoided remagnetization since being deposited in quartz-rich conglomerates at 2.65-3.05 Ga. To address this issue, we have conducted paleomagnetic conglomerate, baked contact, and fold tests in combination with U-Pb geochronology to establish the timing of the metamorphic and alteration events and the peak temperatures experienced by the zircon host rocks. These tests include the first conglomerate test directly on the Hadean-zircon bearing conglomerate at Erawandoo Hill. Although we observed little evidence for remagnetization by recent lightning strikes, we found that the Hadean zircon-bearing rocks and surrounding region have been pervasively remagnetized, with the final major overprinting likely due to thermal and/or aqueous effects from the emplacement of the Warakurna large igneous province at ∼1070 million years ago (Ma). Although localized regions of the Jack Hills might have escaped complete remagnetization, there currently is no robust evidence for pre-depositional (>3.0 Ga) magnetization in the Jack Hills detrital zircons.

Effects of introgression on the genetic population structure of two ecologically and economically important conifer species: lodgepole pine (Pinus contorta var. latifolia) and jack pine (Pinus banksiana).

Science.gov (United States)

Cullingham, Catherine I; Cooke, Janice E K; Coltman, David W

2013-10-01

Forest trees exhibit a remarkable range of adaptations to their environment, but as a result of frequent and long-distance gene flow, populations are often only weakly differentiated. Lodgepole and jack pine hybridize in western Canada, which adds the opportunity for introgression through hybridization to contribute to population structure and (or) adaptive variation. Access to large sample size, high density SNP datasets for these species would improve our ability to resolve population structure, parameterize introgression, and separate the influence of demography from adaptation. To accomplish this, 454 transcriptome reads for lodgepole and jack pine were assembled using Newbler and MIRA, the assemblies mined for SNPs, and 1536 SNPs were selected for typing on lodgepole pine, jack pine, and their hybrids (N = 536). We identified population structure using both Bayesian clustering and discriminate analysis of principle components. Introgressed SNP loci were identified and their influence on observed population structure was assessed. We found that introgressed loci resulted in increased differentiation both within lodgepole and jack pine populations. These findings are timely given the recent mountain pine beetle population expansion in the hybrid zone, and will facilitate future studies of adaptive traits in these ecologically important species.

In conversation with Nobel Laureate Jack Steinberger

CERN Multimedia

2011-01-01

Awarded the 1988 Nobel Prize for Physics for his discovery of the muon neutrino, Jack Steinberger has been part of the CERN establishment for almost 50 years. He recently celebrated his 90th birthday and can still be found in his CERN office on an almost daily basis. If you happened to have a coffee with him… this is what he would tell you: his recollections, and thoughts about the present and future of particle physics.   I’ve been at CERN for 45 years, and I’ve seen this organisation go through a lot. Experiments have grown significantly and so have the aspirations of particle physics. When I did my thesis 64 years ago, I could do it alone in just 6 months and I could get worldwide interesting results. Now, experiments at CERN are made up of hundreds, if not thousands of people, working for 20 years to get a result. My thesis advisor was Enrico Fermi, and in 1953 – unless it was 1952, I’d done my thesis a few years before - he was asked to be t...

Railway crossings: driving the structure under the railway by means of oleodinamic jacks

OpenAIRE

Escribano Méndez, Ramón; López Palomar, Rafael; Ruiz Viedma, Andrés J.

1991-01-01

"The best level crossing is a dead crossing", those involved are accustomed to say Yet, until a short time ago, eliminating these conflictive crossings not only implied a great deal of money but prolonged building work, with the all too familiar sequel of precautions, speed restrictions and problems for rail traffic. However, a brand new system, based on using hydraulic jacks to drive the concrete structure of the crossing to a different level in the track embankment, allows the execution in ...

Eesti pensionisüsteem Euroopa Liidu ühiste pensionimärkide valguses / Lauri Leppik, Ene-Margit Tiit, Andres Võrk

Index Scriptorium Estoniae

Leppik, Lauri, 1964-

2004-01-01

Eesti pensionisüsteemi probleemid on senistest liikmesriikidest erinevad: pensionisüsteemi jätkusuutlikkus on hea ja pensionäride vaesusrisk ei ole kõrge, kuid asendusmäär on suhteliselt madal. See tähendab, et ei suudeta tagada EL-i pensionieesmärki, mis taotleb, et inimesel oleks pensionile jäädes võimalk säilitada oma varasem elatustase. Diagramm. Tabelid. Graafikud

Was Jack the Ripper a Slaughterman? Human-Animal Violence and the World’s Most Infamous Serial Killer

Science.gov (United States)

Knight, Andrew; Watson, Katherine D.

2017-01-01

Simple Summary The identity of Jack the Ripper remains one of the greatest unsolved crime mysteries in history. Jack was notorious both for the brutality of his murders and also for his habit of stealing organs from his victims. His speed and skill in doing so, in conditions of poor light and haste, fueled theories he was a surgeon. However, re-examination of a mortuary sketch from one of his victims has revealed several key aspects that strongly suggest he had no professional surgical training. Instead, the technique used was more consistent with that of a slaughterhouse worker. There were many small-scale slaughterhouses in East London in the 1880s, within which conditions were harsh for animals and workers alike. The brutalizing effects of such work only add to concerns highlighted by modern research that those who commit violence on animals are more likely to target people. Modern slaughterhouses are more humane in some ways but more desensitizing in others, and sociological research has indicated that communities with slaughterhouses are more likely to experience the most violent of crimes. The implications for modern animal slaughtering, and our social reliance on slaughterhouses, are explored. Abstract Hundreds of theories exist concerning the identity of “Jack the Ripper”. His propensity for anatomical dissection with a knife—and in particular the rapid location and removal of specific organs—led some to speculate that he must have been surgically trained. However, re-examination of a mortuary sketch of one of his victims has revealed several aspects of incisional technique highly inconsistent with professional surgical training. Related discrepancies are also apparent in the language used within the only letter from Jack considered to be probably authentic. The techniques he used to dispatch his victims and retrieve their organs were, however, highly consistent with techniques used within the slaughterhouses of the day. East London in the 1880s had

Ecological Responses to Five Years of Experimental Nitrogen Application in an Upland Jack-pine Stand

Science.gov (United States)

Melaschenko, N.; Berryman, S.; Straker, J.; Berg, K.; McDonough, A.; Watmough, S. A.

2016-12-01

A five-year experimental study was conducted to evaluate the response of an upland jack-pine (Pinus banksiana) forest to elevated levels of nitrogen (N) deposition in Northern Alberta. N deposition in the region is expected to increase with industrial expansion of oil sands activity, and there is regional interest to set N critical loads for sensitive ecosystems. In this study, N was applied as NH4NO3 above a jack-pine canopy via helicopter, annually for five years (2010-2015) at dosages equivalent to 5, 10, 15, 20 and 25 kg N ha-1 yr-1. Approximately 35% of the applied N was retained in the canopy while 65% reached understory vegetation dominated by lichens and mosses. We measured a significant increase in tissue N concentrations of common ground lichens (Cladonia mitis and C. stellaris) and ground moss (Pleurozium schreberi) as well as epiphytic lichens (Hypogymnia physodes and Evernia mesomorpha). On an annual basis, the applied N was primarily captured in the lichen and moss understory, dominated by C. mitis. In the highest treatments, N concentrations in C. mitis were 1.5-2.5 times greater than pre-treatment values. Peak N concentrations in the ground moss Pleurozium schreberi (1.4%) indicate that a threshold of N saturation was reached by year 3. We observed no changes in community composition of vascular and non-vascular plants, or changes in vascular plant tissue N. Chlorophyll levels in C. mitis increased with N treatment, but there was no indication of toxicity or changes to decomposition and growth. After five years of N application, only Peltigera polydactylon, a ground cyanolichen, appeared to be negatively impacted where the thalli showed necrosis at deposition loads >10kg N ha-1 yr-1. No changes to biomass or N ecosystem processes were observed. Based on these observations, we provide evidence that the first adverse ecological effects of N deposition in jack-pine stands occurred at deposition rates of 10 kg N ha-1 yr-1.

Fire Regime in Marginal Jack Pine Populations at Their Southern Limit of Distribution, Riding Mountain National Park, Central Canada

Directory of Open Access Journals (Sweden)

Jacques C. Tardif

2016-09-01

Full Text Available In central Canada, long fire history reconstructions are rare. In a context where both anthropogenic and climate influences on fire regime have changed, Parks Canada has a mandate to maintain ecological integrity. Here we present a fire history derived from fire-scarred jack pine (Pinus banksiana Lamb. trees growing at their southern distribution limit in Riding Mountain National Park (RMNP. In Lake Katherine Fire Management Unit (LKFMU, a subregion within the park, fire history was reconstructed from archival records, tree-ring records, and charcoal in lake sediment. From about 1450 to 1850 common era (CE the fire return intervals varied from 37 to 125 years, according to models. During the period 1864–1930 the study area burned frequently (Weibull Mean Fire Intervals between 2.66 and 5.62 years; this period coincided with the end of First Nations occupation and the start of European settlement. Major recruitment pulses were associated with the stand-replacing 1864 and 1894 fires. This period nevertheless corresponded to a reduction in charcoal accumulation. The current fire-free period in LKFMU (1930–today coincides with RMNP establishment, exclusion of First Nations land use and increased fire suppression. Charcoal accumulation further decreased during this period. In the absence of fire, jack pine exclusion in LKFMU is foreseeable and the use of prescribed burning is advocated to conserve this protected jack pine ecosystem, at the southern margins of its range, and in the face of potential climate change.

Narrativa visual de uma obra beat: os vagabundos iluminados de Jack Kerouac

OpenAIRE

TEJERO MARTINEZ, DIANA MARIA

2014-01-01

Este trabajo analiza las técnicas narrativas de los "cómics" aplicadas en la adaptación de la novela "Los vagabundos del Dharma" de Jack Kerouac. Se trata de un trabajo de investigación basado en los estudios de los teóricos Will Eisner y Scott McCloud y de la estudiosa de la adaptación Linda Hutcheon. En la inverstigación se exploran las posibilidades de los "cómics" como medio de expressión gráfica y las características de las adaptaciones de algunas obras...

Kinetics and Mechanism Study of Competitive Inhibition of Jack-Bean Urease by Baicalin

Science.gov (United States)

Tan, Lirong; Su, Jiyan; Wu, Dianwei; Yu, Xiaodan; Su, Zuqing; Wu, Xiaoli; Kong, Songzhi; Lai, Xiaoping; Lin, Ji; Su, Ziren

2013-01-01

Baicalin (BA) is the principal component of Radix Scutellariae responsible for its pharmacological activity. In this study, kinetics and mechanism of inhibition by BA against jack-bean urease were investigated for its therapeutic potential. It was revealed that the IC50 of BA against jack-bean urease was 2.74 ± 0.51 mM, which was proved to be a competitive and concentration-dependent inhibition with slow-binding progress curves. The rapid formation of initial BA-urease complex with an inhibition constant of K i = 3.89 × 10−3 mM was followed by a slow isomerization into the final complex with an overall inhibition constant of K i* = 1.47 × 10−4 mM. High effectiveness of thiol protectors against BA inhibition indicated that the strategic role of the active-site sulfhydryl group of the urease was involved in the blocking process. Moreover, the inhibition of BA was proved to be reversible due to the fact that urease could be reactivated by dithiothreitol but not reactant dilution. Molecular docking assay suggested that BA made contacts with the important activating sulfhydryl group Cys-592 residues and restricted the mobility of the active-site flap. Taken together, it could be deduced that BA was a competitive inhibitor targeting thiol groups of urease in a slow-binding manner both reversibly and concentration-dependently, serving as a promising urease inhibitor for treatments on urease-related diseases. PMID:24198731

Calculations of neutron spectra after neutron-neutron scattering

Energy Technology Data Exchange (ETDEWEB)

Crawford, B E [Gettysburg College, Box 405, Gettysburg, PA 17325 (United States); Stephenson, S L [Gettysburg College, Box 405, Gettysburg, PA 17325 (United States); Howell, C R [Duke University and Triangle Universities Nuclear Laboratory, Durham, NC 27708-0308 (United States); Mitchell, G E [North Carolina State University, Raleigh, NC 27695-8202 (United States); Tornow, W [Duke University and Triangle Universities Nuclear Laboratory, Durham, NC 27708-0308 (United States); Furman, W I [Joint Institute for Nuclear Research, 141980 Dubna (Russian Federation); Lychagin, E V [Joint Institute for Nuclear Research, 141980 Dubna (Russian Federation); Muzichka, A Yu [Joint Institute for Nuclear Research, 141980 Dubna (Russian Federation); Nekhaev, G V [Joint Institute for Nuclear Research, 141980 Dubna (Russian Federation); Strelkov, A V [Joint Institute for Nuclear Research, 141980 Dubna (Russian Federation); Sharapov, E I [Joint Institute for Nuclear Research, 141980 Dubna (Russian Federation); Shvetsov, V N [Joint Institute for Nuclear Research, 141980 Dubna (Russian Federation)

2004-09-01

A direct neutron-neutron scattering length, a{sub nn}, measurement with the goal of 3% accuracy (0.5 fm) is under preparation at the aperiodic pulsed reactor YAGUAR. A direct measurement of a{sub nn} will not only help resolve conflicting results of a{sub nn} by indirect means, but also in comparison to the proton-proton scattering length, a{sub pp}, shed light on the charge-symmetry of the nuclear force. We discuss in detail the analysis of the nn-scattering data in terms of a simple analytical expression. We also discuss calibration measurements using the time-of-flight spectra of neutrons scattered on He and Ar gases and the neutron activation technique. In particular, we calculate the neutron velocity and time-of-flight spectra after scattering neutrons on neutrons and after scattering neutrons on He and Ar atoms for the proposed experimental geometry, using a realistic neutron flux spectrum-Maxwellian plus epithermal tail. The shape of the neutron spectrum after scattering is appreciably different from the initial spectrum, due to collisions between thermal-thermal and thermal-epithermal neutrons. At the same time, the integral over the Maxwellian part of the realistic scattering spectrum differs by only about 6 per cent from that of a pure Maxwellian nn-scattering spectrum.

Ficus deltoidea Jack: A Review on Its Phytochemical and Pharmacological Importance

Directory of Open Access Journals (Sweden)

Hamidun Bunawan

2014-01-01

Full Text Available Ficus deltoidea Jack (Moraceae has had a long history of use in traditional medicine among the Malays to alleviate and heal ailments such as sores, wounds, and rheumatism and as an after-birth tonic and an antidiabetic drug. Modern pharmacological studies demonstrated that this plant has a wide variety of beneficial attributes for human health. Despite its importance, a review of this species has not been published in the scientific literature to date. Here, we review and summarize the historic and current literature concerning the botany, traditional uses, phytochemistry, pharmacological effects, and toxicity of this wonder plant. This summary could be beneficial for future research aiming to exploit the therapeutic potential of this useful, medicinal species.

Differential effects of plant ontogeny and damage type on phloem and foliage monoterpenes in jack pine (Pinus banksiana).

Science.gov (United States)

Erbilgin, Nadir; Colgan, L Jessie

2012-08-01

Coniferous trees have both constitutive and inducible defences that deter or kill herbivores and pathogens. We investigated constitutive and induced monoterpene responses of jack pine (Pinus banksiana Lamb.) to a number of damage types: a fungal associate of the mountain pine beetle (Dendroctonus ponderosae Hopkins), Grosmannia clavigera (Robinson-Jeffrey & R.W. Davidson); two phytohormones, methyl jasmonate (MJ) and methyl salicylate (MS); simulated herbivory; and mechanical wounding. We only included the fungal, MJ and mechanical wounding treatments in the field experiments while all treatments were part of the greenhouse studies. We focused on both constitutive and induced responses between juvenile and mature jack pine trees and differences in defences between phloem and needles. We found that phytohormone applications and fungal inoculation resulted in the greatest increase in monoterpenes in both juvenile and mature trees. Additionally, damage types differentially affected the proportions of individual monoterpenes: MJ-treated mature trees had higher myrcene and β-pinene than fungal-inoculated mature trees, while needles of juveniles inoculated with the fungus contained higher limonene than MJ- or MS-treated juveniles. Although the constitutive monoterpenes were higher in the phloem of juveniles than mature jack pine trees, the phloem of mature trees had a much higher magnitude of induction. Further, induced monoterpene concentrations in juveniles were higher in phloem than in needles. There was no difference in monoterpene concentration between phytohormone applications and G. clavigera inoculation in mature trees, while in juvenile trees MJ was different from both G. clavigera and simulated herbivory in needle monoterpenes, but there was no difference between phytohormone applications and simulated herbivory in the phloem.

Sneaker "jack" males outcompete dominant "hooknose" males under sperm competition in Chinook salmon (Oncorhynchus tshawytscha).

Science.gov (United States)

Young, Brent; Conti, David V; Dean, Matthew D

2013-12-01

In a variety of taxa, males deploy alternative reproductive tactics to secure fertilizations. In many species, small "sneaker" males attempt to steal fertilizations while avoiding encounters with larger, more aggressive, dominant males. Sneaker males usually face a number of disadvantages, including reduced access to females and the higher likelihood that upon ejaculation, their sperm face competition from other males. Nevertheless, sneaker males represent an evolutionarily stable strategy under a wide range of conditions. Game theory suggests that sneaker males compensate for these disadvantages by investing disproportionately in spermatogenesis, by producing more sperm per unit body mass (the "fair raffle") and/or by producing higher quality sperm (the "loaded raffle"). Here, we test these models by competing sperm from sneaker "jack" males against sperm from dominant "hooknose" males in Chinook salmon. Using two complementary approaches, we reject the fair raffle in favor of the loaded raffle and estimate that jack males were ∼1.35 times as likely as hooknose males to fertilize eggs under controlled competitive conditions. Interestingly, the direction and magnitude of this skew in paternity shifted according to individual female egg donors, suggesting cryptic female choice could moderate the outcomes of sperm competition in this externally fertilizing species.

Detrital Zircons From the Jack Hills and Mount Narryer, Western Australia: Geochronological, Morphological, and Geochemical Evidence for Diverse >4000 Ma Source Rocks

Science.gov (United States)

Crowley, J. L.; Myers, J. S.; Sylvester, P. J.; Cox, R. A.

2004-05-01

Detrital zircons from all major clastic units in the Jack Hills and Mount Narryer metasedimentary belts, Western Australia, were analyzed for morphology, internal zoning, inclusion mineralogy, age, and trace element concentrations (latter two obtained by laser-ablation microprobe ICPMS). The results show that zircons were derived from a wide diversity of rocks, including previously described, >4000 Ma grains that are older than any known terrestrial rocks. In three metaconglomerate samples from the western Jack Hills, 4200-3800 Ma zircons ("old grains") comprise 14% of the population, 3800-3600 Ma grains form only 2%, and 3550-3250 Ma zircons ("young grains") are dominant with a significant peak at 3380 Ma. Old and young grains are interpreted as being from similar rock types because they are indistinguishable in trace element concentrations, size (several hundred microns), morphology (subequant, typically fragmented), internal zoning (typically both oscillatory and sector), and U concentration (50-200 ppm). Many of these properties suggest an intermediate plutonic source, whereas an evolved granitic source was previously interpreted from rare-earth element and oxygen isotope data. Detrital zircons in quartzites and metaconglomerates at Mount Narryer differ significantly from zircons from the western Jack Hills. Old grains comprise only 3% (most of which are 4200-4100 Ma), 3800-3600 Ma zircons form 31%, and there are peaks at 3650, 3600, and 3500 Ma. Old and young grains have similar properties that suggest granitic sources, such as elongate prismatic morphology, oscillatory zoning, high U concentrations (100-600 ppm), and xenotime and monazite inclusions. Trace element concentrations are broadly similar to those in Jack Hills zircons, with notable exceptions being generally higher U, smaller Ce and Eu anomalies, and lower Nb/Ta. It is considered unlikely that Jack Hills zircons were derived from granitic gneisses that surround the metasedimentary belts because

Jack Michael's Appointments at the University of Houston and Arizona State University: Reflections from a Former Student

Science.gov (United States)

Mabry, John H.

2016-01-01

Jack Michael was an early enthusiast for what is now called applied behavior analysis. His many seminal contributions were through early publications in applied behavior analysis and the work of the students he trained (e.g., T. Ayllon, M. M. Wolf). His close mentorship of students earned him acclaim as a teacher along with his many theoretical…

Effect of average growing season temperature on seedling germination, survival and growth in jack pine (Pinus banksiana Lamb.)

Science.gov (United States)

A. David; E. Humenberger

2017-01-01

Because jack pine (Pinus banksiana Lamb.) is serotinous, it retains multiple years of cones until environmental conditions are favorable for releasing seed. These cones, which contain seed cohorts that developed under a variety of growing seasons, can be accurately aged using bud scale scars on twigs and branches. By calculating the average daily...

Applying the vantage PDMS to jack-up drilling ships

Science.gov (United States)

Yin, Peng; Chen, Yuan-Ming; Cui, Tong-Kai; Wang, Zi-Shen; Gong, Li-Jiang; Yu, Xiang-Fen

2009-09-01

The plant design management system (PDMS) is an integrated application which includes a database and is useful when designing complex 3-D industrial projects. It could be used to simplify the most difficult part of a subsea oil extraction project—detailed pipeline design. It could also be used to integrate the design of equipment, structures, HVAC, E-ways as well as the detailed designs of other specialists. This article mainly examines the applicability of the Vantage PDMS database to pipeline projects involving jack-up drilling ships. It discusses the catalogue (CATA) of the pipeline, the spec-world (SPWL) of the pipeline, the bolt tables (BLTA) and so on. This article explains the main methods for CATA construction as well as problem in the process of construction. In this article, the authors point out matters needing attention when using the Vantage PDMS database in the design process and discuss partial solutions to these questions.

Modular jack-up platform debuts in Peru's Amazon jungle

Energy Technology Data Exchange (ETDEWEB)

Franco, A.

1975-08-11

Robishaw Engineering Inc., Houston, has designed and built a jack-up platform based on a modular flotation and erection system that allows exploratory and development drilling year round in any location that cannot be reached by conventional equipment. All components are light enough to be transported by helicopters rated for 4000-lb loads, yet strong and buoyant enough to serve as working platforms. The pile-supported self-elevating drilling platform consists of H-shaped steel girders joined by pin connectors and tension wires. Deck panels are steel-plated. When elevated on steel pilings, the platform can support loads imposed by rigs capable of drilling to 18,000 ft. One such unit is currently being used in the Peruvian rain forest.

Characterization of inclusions in terrestrial impact formed zircon: Constraining the formation conditions of Hadean zircon from Jack Hills, Western Australia

Science.gov (United States)

Faltys, J. P.; Wielicki, M. M.; Sizemore, T. M.

2017-12-01

Due to the discovery and subsequent geochemical analysis of Hadean terrestrial material (e.g. detrital zircon from Jack Hills, Western Australia), a dramatic paradigm shift has occurred in the hypothesized near surface conditions of the first 500 million years of Earth's evolution. From a hellish setting riddled with impactors and not fit for life to a much milder environment that may have been uniquely suitable for the origin of life. Geochemical analyses of these ancient materials have been used to suggest the presence of water at or near the surface as well as the existence of continental crust during the Hadean, both of which have been suggested as necessary for the origin of life. However, the intensity of extraterrestrial bombardment during the Hadean and the effects of such events on the origin of life remains poorly understood. Clearly, as evidenced by Phanerozoic impact events, extraterrestrial impactors have the potential to dramatically effect the environment, particularly the biosphere. Early Earth likely experienced multiple large impact events, as evidenced by the lunar record, however whether those impacts were sufficient to frustrate the origin of life remains an open question. Although multiple lines of evidence, including the inclusion population, suggest the formation of Hadean zircon from Jack Hills as crystallizing in an under-thrust environment from S-type magmas, a recent study has suggested their formation in an impact melt environment analogous to a portion of the Sudbury Igneous Complex at the Sudbury impact structure. To determine between these two formation scenarios we have under-taken an inclusion study of terrestrial impact formed zircon from four of the largest terrestrial impact structures (Sudbury, Canada; Manicouagan, Canada; Vredefort, South Africa; Morokweng, South Africa), to compare to the vast inclusion dataset that exists for Jack Hills zircon. Preliminary data suggests a different inclusion population, from Hadean zircon

Neutron--neutron logging

International Nuclear Information System (INIS)

Allen, L.S.

1977-01-01

A borehole logging tool includes a steady-state source of fast neutrons, two epithermal neutron detectors, and two thermal neutron detectors. A count rate meter is connected to each neutron detector. A first ratio detector provides an indication of the porosity of the formation surrounding the borehole by determining the ratio of the outputs of the two count rate meters connected to the two epithermal neutron detectors. A second ratio detector provides an indication of both porosity and macroscopic absorption cross section of the formation surrounding the borehole by determining the ratio of the outputs of the two count rate meters connected to the two thermal neutron detectors. By comparing the signals of the two ratio detectors, oil bearing zones and salt water bearing zones within the formation being logged can be distinguished and the amount of oil saturation can be determined. 6 claims, 2 figures

A phyt osociological classification of the vegetation of the Jack Scott Nature Reserve*

Directory of Open Access Journals (Sweden)

B. J. Coetzee

1974-12-01

Full Text Available The vegetation of the Jack Scott Nature Reserve in the Central Bankenveld Veld Type is classified chiefly by the Braun-Blanquet Table Method. Habitat features, physiognomy, total floristic composition, differentiating species, woody plants and prominent grasses and forbs are presented for each community. Characterizing habitat features, in order of importance for the communities, are: exposure, soil texture, geology, slope, aspect, degree of rockiness and previous ploughing. The classification correlates well with the major physiographic and climatic variation in the Reserve and generally does not cut across main physiognomic types. The communities are potentially homogeneous management units.

Multi-function magnetic jack control drive mechanism

International Nuclear Information System (INIS)

Bollinger, L.R.; Crawford, D.C.

1986-01-01

A multi-function magnetic jack control drive mechanism is described for controlling a nuclear reactor comprising: an elongate pressure housing; closely-spaced drive rods located in the pressure housing, the drive rod being connected to a reactor rod which is insertable in a reactor core; electrochemical stationary latch means which are selectively actuatable for holding a respective one of the drive rods stationary with respect to the pressure housing, the plurality of stationary latch means including at least one coil located about the pressure housing; longitudinally spaced electromechanical movable latch means, individually associated with one of the drive rods and each including a base for the drive rod associated therewith, for, when actuated, holding the associated drive rod stationary with respect to the base associated therewith, the movable latch means including an associated coil located about the pressure housing; and longitudinally spaced electromechanical lift means, individually associated with the base, for, when actuated, moving an associated base longitudinally along the pressure housing from a first position to a second position to thereby enable movement of one or more of the other drive rods longitudinally independently of the other drive rods in response to sequential and repeated operation of the electromechanical means, the lift means including an associated coil located about the pressure housing

Automated detection and mapping of crown discolouration caused by jack pine budworm with 2.5 m resolution multispectral imagery

Science.gov (United States)

Leckie, Donald G.; Cloney, Ed; Joyce, Steve P.

2005-05-01

Jack pine budworm ( Choristoneura pinus pinus (Free.)) is a native insect defoliator of mainly jack pine ( Pinus banksiana Lamb.) in North America east of the Rocky Mountains. Periodic outbreaks of this insect, which generally last two to three years, can cause growth loss and mortality and have an important impact ecologically and economically in terms of timber production and harvest. The jack pine budworm prefers to feed on current year needles. Their characteristic feeding habits cause discolouration or reddening of the canopy. This red colouration is used to map the distribution and intensity of defoliation that has taken place that year (current defoliation). An accurate and consistent map of the distribution and intensity of budworm defoliation (as represented by the red discolouration) at the stand and within stand level is desirable. Automated classification of multispectral imagery, such as is available from airborne and new high resolution satellite systems, was explored as a viable tool for objectively classifying current discolouration. Airborne multispectral imagery was acquired at a 2.5 m resolution with the Multispectral Electro-optical Imaging Sensor (MEIS). It recorded imagery in six nadir looking spectral bands specifically designed to detect discolouration caused by budworm and a near-infrared band viewing forward at 35° was also used. A 2200 nm middle infrared image was acquired with a Daedalus scanner. Training and test areas of different levels of discolouration were created based on field observations and a maximum likelihood supervized classification was used to estimate four classes of discolouration (nil-trace, light, moderate and severe). Good discrimination was achieved with an overall accuracy of 84% for the four discolouration levels. The moderate discolouration class was the poorest at 73%, because of confusion with both the severe and light classes. Accuracy on a stand basis was also good, and regional and within stand

A Comparison Between Measured and Predicted Hydrodynamic Damping for a Jack-Up Rig Model

DEFF Research Database (Denmark)

Laursen, Thomas; Rohbock, Lars; Jensen, Jørgen Juncher

1996-01-01

An extensive set of measurements funded by the EU project Large Scale Facilities Program has been carried out on a model of a jack-up rig at the Danish Hydraulic Institute. The test serieswere conducted by MSC and include determination of base shears and overturning moments in both regular...... methods.In the comparison between the model test results and the theoretical predictions, thehydro-dynamic damping proves to be the most important uncertain parameter. It is shown thata relative large hydrodynamic damping must be assumed in the theoretical calculations in orderto predict the measured...

Neutronics of pulsed spallation neutron sources

CERN Document Server

Watanabe, N

2003-01-01

Various topics and issues on the neutronics of pulsed spallation neutron sources, mainly for neutron scattering experiments, are reviewed to give a wide circle of readers a better understanding of these sources in order to achieve a high neutronic performance. Starting from what neutrons are needed, what the spallation reaction is and how to produce slow-neutrons more efficiently, the outline of the target and moderator neutronics are explained. Various efforts with some new concepts or ideas have already been devoted to obtaining the highest possible slow-neutron intensity with desired pulse characteristics. This paper also reviews the recent progress of such efforts, mainly focused on moderator neutronics, since moderators are the final devices of a neutron source, which determine the source performance. Various governing parameters for neutron-pulse characteristics such as material issues, geometrical parameters (shape and dimensions), the target-moderator coupling scheme, the ortho-para-hydrogen ratio, po...

Neutronics of pulsed spallation neutron sources

International Nuclear Information System (INIS)

Watanabe, Noboru

2003-01-01

Various topics and issues on the neutronics of pulsed spallation neutron sources, mainly for neutron scattering experiments, are reviewed to give a wide circle of readers a better understanding of these sources in order to achieve a high neutronic performance. Starting from what neutrons are needed, what the spallation reaction is and how to produce slow-neutrons more efficiently, the outline of the target and moderator neutronics are explained. Various efforts with some new concepts or ideas have already been devoted to obtaining the highest possible slow-neutron intensity with desired pulse characteristics. This paper also reviews the recent progress of such efforts, mainly focused on moderator neutronics, since moderators are the final devices of a neutron source, which determine the source performance. Various governing parameters for neutron-pulse characteristics such as material issues, geometrical parameters (shape and dimensions), the target-moderator coupling scheme, the ortho-para-hydrogen ratio, poisoning, etc are discussed, aiming at a high performance pulsed spallation source

Neoarchean metamorphism recorded in high-precision Sm-Nd isotope systematics of garnets from the Jack Hills (Western Australia)

Science.gov (United States)

Eccles, K. A.; Baxter, E. F.; Mojzsis, S. J.; Marschall, H.; Williams, M. L.; Jercinovic, M. J.

2013-12-01

Studies of metasedimentary rocks from the Jack Hills, which host Earth's oldest known detrital minerals, have focused on zircon and occasionally monazite or xenotime, but no attention has been directed toward one of the most common mineral markers of metamorphism: garnet. Garnet can provide a record of the post-depositional, prograde metamorphic history of Archean metasedimentary rocks. Additionally, the use of a newly developed detrital garnet dating technique [1,2] may reveal information about pre-depositional metamorphism that could address lingering questions about the nature and timing of Earth's earliest tectonometamorphic events. Here we investigate garnet from the Jack Hills metasedimentary rocks to test whether they record in situ metamorphism or are a detrital relict of even older metamorphic events. We identified garnet in two bulk quartz-pebble conglomerate samples collected from the 'discovery' outcrop at Eranondoo Hill in the Jack Hills of Western Australia. Electron microprobe analyses of polished grains and SEM measurements of unpolished grain surfaces are consistent, revealing garnet composition indicative of a single generation/population of predominantly almandine-spessartine solid solution (~10-35% mole fraction spessartine). Compositional maps of garnet grains reveal little zoning and no discontinuities, most consistent with a single growth event. Dating Jack Hills' garnet via the Sm-Nd system is possible due to continued development of small sample analysis techniques, including running NdO+ TIMS analyses with Ta2O5 activator [3] permitting Ma for two point isochrons between clean garnet (Sm/Nd ≥ 1.0) and their leached inclusion populations [2]. Four grouped garnet grain separates from one sample yield preliminary dates of 2703.6×6.0Ma, 2612.4×6.0Ma, 2605.0×5.5Ma, and 2567.3×8.3Ma, while the second sample yielded a date of 2579.6×4.6 Ma (2σ). Compositional and geochronologic data indicate likely in situ garnet growth during a late

Prevalence, severity, and natural history of jack jumper ant venom allergy in Tasmania.

Science.gov (United States)

Brown, Simon G A; Franks, Rodney W; Baldo, Brian A; Heddle, Robert J

2003-01-01

The jack jumper ant (Myrmecia pilosula) is responsible for greater than 90% of Australian ant venom allergy. However, deaths have only been recorded in the island of Tasmania. We sought to determine the prevalence, clinical features, natural history, and predictors of severity of M pilosula sting allergy in Tasmania. We performed a random telephone survey supported by serum venom-specific IgE analysis, review of emergency department presentations, and follow-up of allergic volunteers. M pilosula, honeybee (Apis mellifera), and yellow jacket wasp (Vespula germanica) sting allergy prevalences were 2.7%, 1.4%, and 0.6% compared with annual sting exposure rates of 12%, 7%, and 2%, respectively. Similarly, emergency department presentations with anaphylaxis to M pilosula were double those for honeybee. M pilosula allergy prevalence increased with age of 35 years or greater (odds ratio [OR], 2.4) and bee sting allergy (OR, 16.9). Patients 35 years of age or older had a greater risk of hypotensive reactions (OR, 2.9). Mueller reaction grades correlated well with adrenaline use. During follow-up, 79 (70%) of 113 jack jumper stings caused anaphylaxis. Prior worst reaction severity predicted the likelihood and severity of follow-up reactions; only 3 subjects had more severe reactions. Venom-specific IgE levels and other clinical features, including comorbidities, were not predictive of severity. Sting allergy prevalence is determined by age and exposure rate. M pilosula sting exposure in Tasmania is excessive compared with that found in mainland Australia, and there is a high systemic reaction risk in allergic people on re-sting. Prior worst reaction severity (Mueller grade) and age predict reaction severity and might be used to guide management.

Neutron radiography with ultracold neutrons

International Nuclear Information System (INIS)

Bates, J.C.

1981-01-01

The neutron transmission factor of very thin films may be low if the neutron energy is comparable to the pseudo-potential of the film material. Surprisingly, perhaps, it is relatively easy to obtain neutrons with such low energies in sufficient numbers to produce neutron radiographs. (orig.)

Neutron Skins and Neutron Stars

OpenAIRE

Piekarewicz, J.

2013-01-01

The neutron-skin thickness of heavy nuclei provides a fundamental link to the equation of state of neutron-rich matter, and hence to the properties of neutron stars. The Lead Radius Experiment ("PREX") at Jefferson Laboratory has recently provided the first model-independence evidence on the existence of a neutron-rich skin in 208Pb. In this contribution we examine how the increased accuracy in the determination of neutron skins expected from the commissioning of intense polarized electron be...

Analysis of ITER NbTi and Nb3Sn CICCs experimental minimum quench energy with JackPot, MCM and THEA models

Science.gov (United States)

Bagni, T.; Duchateau, J. L.; Breschi, M.; Devred, A.; Nijhuis, A.

2017-09-01

Cable-in-conduit conductors (CICCs) for ITER magnets are subjected to fast changing magnetic fields during the plasma-operating scenario. In order to anticipate the limitations of conductors under the foreseen operating conditions, it is essential to have a better understanding of the stability margin of magnets. In the last decade ITER has launched a campaign for characterization of several types of NbTi and Nb3Sn CICCs comprising quench tests with a singular sine wave fast magnetic field pulse and relatively small amplitude. The stability tests, performed in the SULTAN facility, were reproduced and analyzed using two codes: JackPot-AC/DC, an electromagnetic-thermal numerical model for CICCs, developed at the University of Twente (van Lanen and Nijhuis 2010 Cryogenics 50 139-148) and multi-constant-model (MCM) (Turck and Zani 2010 Cryogenics 50 443-9), an analytical model for CICCs coupling losses. The outputs of both codes were combined with thermal, hydraulic and electric analysis of superconducting cables to predict the minimum quench energy (MQE) (Bottura et al 2000 Cryogenics 40 617-26). The experimental AC loss results were used to calibrate the JackPot and MCM models and to reproduce the energy deposited in the cable during an MQE test. The agreement between experiments and models confirm a good comprehension of the various CICCs thermal and electromagnetic phenomena. The differences between the analytical MCM and numerical JackPot approaches are discussed. The results provide a good basis for further investigation of CICC stability under plasma scenario conditions using magnetic field pulses with lower ramp rate and higher amplitude.

Hi-Jack: a novel computational framework for pathway-based inference of host–pathogen interactions

KAUST Repository

Kleftogiannis, Dimitrios A.

2015-03-09

Motivation: Pathogens infect their host and hijack the host machinery to produce more progeny pathogens. Obligate intracellular pathogens, in particular, require resources of the host to replicate. Therefore, infections by these pathogens lead to alterations in the metabolism of the host, shifting in favor of pathogen protein production. Some computational identification of mechanisms of host-pathogen interactions have been proposed, but it seems the problem has yet to be approached from the metabolite-hijacking angle. Results: We propose a novel computational framework, Hi-Jack, for inferring pathway-based interactions between a host and a pathogen that relies on the idea of metabolite hijacking. Hi-Jack searches metabolic network data from hosts and pathogens, and identifies candidate reactions where hijacking occurs. A novel scoring function ranks candidate hijacked reactions and identifies pathways in the host that interact with pathways in the pathogen, as well as the associated frequent hijacked metabolites. We also describe host-pathogen interaction principles that can be used in the future for subsequent studies. Our case study on Mycobacterium tuberculosis (Mtb) revealed pathways in human-e.g. carbohydrate metabolism, lipids metabolism and pathways related to amino acids metabolism-that are likely to be hijacked by the pathogen. In addition, we report interesting potential pathway interconnections between human and Mtb such as linkage of human fatty acid biosynthesis with Mtb biosynthesis of unsaturated fatty acids, or linkage of human pentose phosphate pathway with lipopolysaccharide biosynthesis in Mtb. © The Author 2015. Published by Oxford University Press. All rights reserved.

Neutron-neutron probe for uranium exploration

International Nuclear Information System (INIS)

Smith, R.C.

1979-01-01

A neutron activation probe for assaying the amount of fissionable isotopes in an ore body is described which comprises a casing which is movable through a borehole in the ore body, a neutron source and a number of delayed neutron detectors arranged colinearly in the casing below the neutron source for detecting delayed neutrons

Durable Reliability of Jack-up Platforms. The impact of Fatigue, Fracture and Effect of Extreme Environmental Loads on the Structural Reliability

NARCIS (Netherlands)

Shabakhty, N.

2004-01-01

A variety of factors is governing the operational conditions of jack-up platforms. The platforms are moved to different locations, which are causing changes in water depth, environmental and seabed conditions, drilling depths, payload etc. Insight should be gained in how the different factors affect

A Group Interview about Publishing with Professor Jack Zipes

Directory of Open Access Journals (Sweden)

Emma Louise Parfitt

2016-10-01

Full Text Available The conversation piece is the product of a group interview with Professor Jack Zipes and provides useful insights about publishing for early career researchers across disciplines. Based on his wider experiences as academic and writer, Professor Zipes answered questions from PhD researchers about: writing books, monographs and edited collections; turning a PhD thesis into a monograph; choosing and approaching publishers; and the advantages of editing books and translations. It presents some general advice for writing and publishing aimed at postgraduate students. Professor Zipes is an Emeritus Professor at the University of Minnesota Twin Cities, United States, a world expert on fairy tales and storytelling highlighting the social and historical dimensions of them. Zipes has forty years of experience publishing academic and mass-market books, editing anthologies, and translating work from French, German and Italian. His best known books are Breaking the Magic Spell (1979, Fairy Tales and the Art of Subversion (1983, The Irresistible Fairy Tale: The Cultural and Social History of a Genre (2012, and The Original Folk and Fairy Tales of the Brothers Grimm (2014.

Acheronta movebo. Resilencia y revolución en The Mexican (1911 de Jack London

Directory of Open Access Journals (Sweden)

Eduardo González de la Fuente

2016-07-01

Full Text Available Este artículo maneja uno de los relatos pugilísticos de Jack London, The Mexican (1911, para explorar el mundo del boxeo como lugar público de conflictos sociales e ideológicos identificados y significados en la proteica figura del boxeador. Así pues, el ring es susceptible de devenir y analizarse como un espacio de práctica política, de antagonismo y debate que, en su reglada exposición de violencias carnales y simbólicas, condensa una particular síntesis efectiva de corporalidades y discursos.

Quantitative neutron radiography using neutron absorbing honeycomb

International Nuclear Information System (INIS)

Tamaki, Masayoshi; Oda, Masahiro; Takahashi, Kenji; Ohkubo, Kohei; Tasaka, Kanji; Tsuruno, Akira; Matsubayashi, Masahito.

1993-01-01

This investigation concerns quantitative neutron radiography and computed tomography by using a neutron absorbing honeycomb collimator. By setting the neutron absorbing honeycomb collimator between object and imaging system, neutrons scattered in the object were absorbed by the honeycomb material and eliminated before coming to the imaging system, but the neutrons which were transmitted the object without interaction could reach the imaging system. The image by purely transmitted neutrons gives the quantitative information. Two honeycombs were prepared with coating of boron nitride and gadolinium oxide and evaluated for the quantitative application. The relation between the neutron total cross section and the attenuation coefficient confirmed that they were in a fairly good agreement. Application to quantitative computed tomography was also successfully conducted. The new neutron radiography method using the neutron-absorbing honeycomb collimator for the elimination of the scattered neutrons improved remarkably the quantitativeness of the neutron radiography and computed tomography. (author)

Neutron dosimetry; Dosimetria de neutrons

Energy Technology Data Exchange (ETDEWEB)

Fratin, Luciano

1993-12-31

A neutron irradiation facility was designed and built in order to establish a procedure for calibrating neutron monitors and dosemeters. A 185 GBq {sup 241} Am Be source of known is used as a reference source. The irradiation facility using this source in the air provides neutron dose rates between 9 nSv s{sup -1} and 0,5 {sup {mu}}Sv s{sup -1}. A calibrated 50 nSv s{sup -1} thermal neutron field is obtained by using a specially designed paraffin block in conjunction with the {sup 241} Am Be source. A Bonner multisphere spectrometer was calibrated, using a procedure based on three methods proposed by international standards. The unfold {sup 241} Am Be neutron spectrum was determined from the Bonner spheres data and resulted in a good agreement with expected values for fluence rate, dose rate and mean energy. A dosimetric system based on the electrochemical etching of CR-39 was developed for personal dosimetry. The dosemeter badge using a (n,{alpha}) converter, the etching chamber and high frequency power supply were designed and built specially for this project. The electrochemical etching (ECE) parameters used were: a 6N KOH solution, 59 deg C, 20 kV{sub pp} cm{sup -1}, 2,0 kHz, 3 hours of ECE for thermal and intermediate neutrons and 6 hours for fast neutrons. The calibration factors for thermal, intermediate and fast neutrons were determined for this personal dosemeter. The sensitivities determined for the developed dosimetric system were (1,46{+-} 0,09) 10{sup 4} tracks cm{sup -2} mSv{sup -1} for thermal neutrons, (9{+-}3) 10{sup 2} tracks cm{sup -2} mSV{sup -1} for intermediate neutrons and (26{+-}4) tracks cm{sup -2} mSv{sup -1} for fast neutrons. The lower and upper limits of detection were respectively 0,002 mSv and 0,6 mSv for thermal neutrons, 0,04 mSv and 8 mSv for intermediate neutrons and 1 mSv and 12 mSv for fast neutrons. In view of the 1990`s ICRP recommendations, it is possible to conclude that the personal dosemeter described in this work is

Neutron dosimetry; Dosimetria de neutrons

Energy Technology Data Exchange (ETDEWEB)

Fratin, Luciano

1994-12-31

A neutron irradiation facility was designed and built in order to establish a procedure for calibrating neutron monitors and dosemeters. A 185 GBq {sup 241} Am Be source of known is used as a reference source. The irradiation facility using this source in the air provides neutron dose rates between 9 nSv s{sup -1} and 0,5 {sup {mu}}Sv s{sup -1}. A calibrated 50 nSv s{sup -1} thermal neutron field is obtained by using a specially designed paraffin block in conjunction with the {sup 241} Am Be source. A Bonner multisphere spectrometer was calibrated, using a procedure based on three methods proposed by international standards. The unfold {sup 241} Am Be neutron spectrum was determined from the Bonner spheres data and resulted in a good agreement with expected values for fluence rate, dose rate and mean energy. A dosimetric system based on the electrochemical etching of CR-39 was developed for personal dosimetry. The dosemeter badge using a (n,{alpha}) converter, the etching chamber and high frequency power supply were designed and built specially for this project. The electrochemical etching (ECE) parameters used were: a 6N KOH solution, 59 deg C, 20 kV{sub pp} cm{sup -1}, 2,0 kHz, 3 hours of ECE for thermal and intermediate neutrons and 6 hours for fast neutrons. The calibration factors for thermal, intermediate and fast neutrons were determined for this personal dosemeter. The sensitivities determined for the developed dosimetric system were (1,46{+-} 0,09) 10{sup 4} tracks cm{sup -2} mSv{sup -1} for thermal neutrons, (9{+-}3) 10{sup 2} tracks cm{sup -2} mSV{sup -1} for intermediate neutrons and (26{+-}4) tracks cm{sup -2} mSv{sup -1} for fast neutrons. The lower and upper limits of detection were respectively 0,002 mSv and 0,6 mSv for thermal neutrons, 0,04 mSv and 8 mSv for intermediate neutrons and 1 mSv and 12 mSv for fast neutrons. In view of the 1990`s ICRP recommendations, it is possible to conclude that the personal dosemeter described in this work is

Neutron detection efficiency determinations for the TUNL neutron-neutron and neutron-proton scattering-length measurements

International Nuclear Information System (INIS)

Trotter, D.E. Gonzalez; Meneses, F. Salinas; Tornow, W.; Crowell, A.S.; Howell, C.R.; Schmidt, D.; Walter, R.L.

2009-01-01

The methods employed and the results obtained from measurements and calculations of the detection efficiency for the neutron detectors used at Triangle Universities Nuclear Laboratory (TUNL) in the simultaneous determination of the 1 S 0 neutron-neutron and neutron-proton scattering lengths a nn and a np , respectively, are described. Typical values for the detector efficiency were 0.3. Very good agreement between the different experimental methods and between data and calculation has been obtained in the neutron energy range below E n =13MeV.

Neutron detection efficiency determinations for the TUNL neutron-neutron and neutron-proton scattering-length measurements

Energy Technology Data Exchange (ETDEWEB)

Trotter, D.E. Gonzalez [Department of Physics, Duke University and Triangle Universities Nuclear Laboratory, Durham, NC 27708-0308 (United States)], E-mail: crowell@tunl.duke.edu; Meneses, F. Salinas [Department of Physics, Duke University and Triangle Universities Nuclear Laboratory, Durham, NC 27708-0308 (United States); Tornow, W. [Department of Physics, Duke University and Triangle Universities Nuclear Laboratory, Durham, NC 27708-0308 (United States)], E-mail: tornow@tunl.duke.edu; Crowell, A.S.; Howell, C.R. [Department of Physics, Duke University and Triangle Universities Nuclear Laboratory, Durham, NC 27708-0308 (United States); Schmidt, D. [Physikalisch-Technische Bundesanstalt, D-38116, Braunschweig (Germany); Walter, R.L. [Department of Physics, Duke University and Triangle Universities Nuclear Laboratory, Durham, NC 27708-0308 (United States)

2009-02-11

The methods employed and the results obtained from measurements and calculations of the detection efficiency for the neutron detectors used at Triangle Universities Nuclear Laboratory (TUNL) in the simultaneous determination of the {sup 1}S{sub 0} neutron-neutron and neutron-proton scattering lengths a{sub nn} and a{sub np}, respectively, are described. Typical values for the detector efficiency were 0.3. Very good agreement between the different experimental methods and between data and calculation has been obtained in the neutron energy range below E{sub n}=13MeV.

Neutron stars

International Nuclear Information System (INIS)

Irvine, J.M.

1978-01-01

The subject is covered in chapters entitled: introduction (resume of stellar evolution, gross characteristics of neutron stars); pulsars (pulsar characteristics, pulsars as neutron stars); neutron star temperatures (neutron star cooling, superfluidity and superconductivity in neutron stars); the exterior of neutron stars (the magnetosphere, the neutron star 'atmosphere', pulses); neutron star structure; neutron star equations of state. (U.K.)

Raccoglier lettere. Le “Vico collaborations” di Jack W. Stauffacher e Dennis Letbetter

Directory of Open Access Journals (Sweden)

Armando, David

2010-01-01

Full Text Available Starting in the early ’70s the San Francisco printer and typographer Jack W. Stauffacher undertook a graphic exploration of Vico’s works, which continued during the past decade together with the photographer Dennis Letbetter. The aim of this article is to present their experience - which is at the same time poetic and historically attentive, focusing on the relationships between text and images, and on the typographical and physical qualities of 18th century editions - to an audience which includes Italian Vico scholars. The text is composed of a brief introduction and an interview with the two artists, and is followed (pp. 94-180 by a photographic presentation of their "Vico collaborations".

Proterozoic events recorded in quartzite cobbles at Jack Hills, Western Australia: New constraints on sedimentation and source of > 4 Ga zircons

Science.gov (United States)

Grange, Marion L.; Wilde, Simon A.; Nemchin, Alexander A.; Pidgeon, Robert T.

2010-03-01

Rare heavy mineral bands within quartzite cobbles were identified in two conglomerate units within the Jack Hills belt, Western Australia. Seven zircon-bearing cobbles were analysed from one location (site 152) and three from another (site 154), both approximately 1 km west of the site where zircons in excess of 4 Ga are abundant (W74 'discovery' site). Individual pebbles from the 152 site reveal three distinctive features, containing either zircons > 3.0 Ga in age, 4 Ga was discovered from the entire suite of pebbles, in contrast to the well-studied W74 site. A single detrital zircon with an age of 1220 ± 42 Ma from location 152 is the youngest grain so far reported from sedimentary rocks at Jack Hills. It shows magmatic oscillatory zoning and thus implies at least two sedimentary cycles within the Proterozoic; requiring erosion of an igneous precursor, incorporation into a clastic sediment, induration and subsequent erosion and transport to be hosted in the conglomerate. The nearest source for rocks of this age is the Bangemall Supergroup in the Collier Basin, ˜ 100 km northeast in the Capricorn Orogen. This would imply tectonic interleaving of originally more extensive Bangemall rocks, possibly related to activity along the Cargarah Shear Zone that traverses the Jack Hills belt. The lack of > 4.1 Ga zircons in the pebbles is highly significant, suggesting the immediate source of ancient zircons was no longer present at the Earth's surface. This equates with a general lack of ancient crystals noted in rocks that contain Proterozoic zircons from previous studies and implies that such grains diminish in number as earlier sedimentary rocks were successively recycled.

Jack-knife stretching promotes flexibility of tight hamstrings after 4 weeks: a pilot study.

Science.gov (United States)

Sairyo, Koichi; Kawamura, Takeshi; Mase, Yasuyoshi; Hada, Yasushi; Sakai, Toshinori; Hasebe, Kiyotaka; Dezawa, Akira

2013-08-01

Tight hamstrings are reported to be one of the causes of low back pain. However, there have been few reports on effective stretching procedures for the tight hamstrings. The so-called jack-knife stretch, an active-static type of stretching, can efficiently increase the flexibility of tight hamstrings. To evaluate hamstring tightness before and after the 4-week stretching protocol in healthy volunteer adults and patients aged under 18 years with low back pain. For understanding the hamstrings tightness, we measured two parameters including (1) finger to floor distance (FFD) and (2) pelvis forward inclination angle (PFIA). Eight healthy adult volunteers who had no lumbar or hip problems participated in this study (mean age: 26.8 years). All lacked flexibility and their FFD were positive before the experiment. Subjects performed 2 sets of the jack-knife stretch every day for 4 weeks. One set consisted of 5 repetitions, each held for 5 s. Before and during the 4-week experiment, the FFD and PFIA of toe-touching tests were measured weekly. For 17 of the sports players aged under 18, only FFD was measured. In adult volunteers, FFD was 14.1 ± 6.1 cm before the experiment and decreased to -8.1 ± 3.7 cm by the end of week 4, indicating a gain in flexibility of 22.2 cm. PFIA was 50.6 ± 8.2 before the experiment and 83.8 ± 5.8 degrees after. Before and after the experiment, the differences were significant (p hamstrings.

Pulsed neutron sources for epithermal neutrons

International Nuclear Information System (INIS)

Windsor, C.G.

1978-01-01

It is shown how accelerator based neutron sources, giving a fast neutron pulse of short duration compared to the neutron moderation time, promise to open up a new field of epithermal neutron scattering. The three principal methods of fast neutron production: electrons, protons and fission boosters will be compared. Pulsed reactors are less suitable for epithermal neutrons and will only be briefly mentioned. The design principle of the target producing fast neutrons, the moderator and reflector to slow them down to epithermal energies, and the cell with its beam tubes and shielding will all be described with examples taken from the new Harwell electron linac to be commissioned in 1978. A general comparison of pulsed neutron performance with reactors is fraught with difficulties but has been attempted. Calculation of the new pulsed source fluxes and pulse widths is now being performed but we have taken the practical course of basing all comparisons on extrapolations from measurements on the old 1958 Harwell electron linac. Comparisons for time-of-flight and crystal monochromator experiments show reactors to be at their best at long wavelengths, at coarse resolution, and for experiments needing a specific incident wavelength. Even existing pulsed sources are shown to compete with the high flux reactors in experiments where the hot neutron flux and the time-of-flight methods can be best exploited. The sources under construction can open a new field of inelastic neutron scattering based on energy transfer up to an electron volt and beyond

Neutron radiography using neutron imaging plate

International Nuclear Information System (INIS)

Chankow, Nares; Wonglee, Sarinrat

2008-01-01

Full text: The aims of this research are to study properties of neutron imaging plate, to obtain a suitable condition for neutron radiography and to use the neutron imaging plate for testing of materials nondestructively. The experiments were carried out by using a neutron beam from the Thai Research Reactor TRR-1/M1 at a power of 1.2 MW. A BAS-ND 2040 FUJI neutron imaging plate and a MX125 Kodak X-ray film/Gadolinium neutron converter screen combination were tested for comparison. It was found that the photostimulated light (PSL) read out of the imaging plate was directly proportional to the exposure time. It was also found that radiography with neutron using the imaging plate was approximately 40 times faster than the conventional neutron radiography using x-ray film/Gd converter screen combination. The sensitivity of the imaging plate to gamma-rays was investigated by using gamma-rays from an 192 Ir and a 60 Co radiographic sources. The imaging plate was found to be 5-6 times less sensitive to gamma-rays than a FUJI BAS-MS 2040 gamma-ray imaging plate. Finally, some specimens were selected to be radiographed with neutrons using the imaging plate and the x-ray film/Gd converter screen combination in comparison to x-rays. Parts containing light elements could be clearly observed by the two neutron radiographic techniques. It could be concluded that the image quality from the neutron imaging plate was comparable to the conventional x-ray film/Gd converter screen combination but the exposure time could be approximately reduced by a factor of 40

Ultracold neutrons

International Nuclear Information System (INIS)

Steenstrup, S.

Briefly surveys recent developments in research work with ultracold neutrons (neutrons of very low velocity, up to 10 m/s at up to 10 -7 eV and 10 -3 K). Slow neutrons can be detected in an ionisation chamber filled with B 10 F 3 . Very slow neutrons can be used for investigations into the dipole moment of neutrons. Neutrons of large wave length have properties similar to those of light. The limit angle for total reflection is governed by the wave length and by the material. Total reflection can be used to filter ultracold neutrons out of the moderator material of a reactor. Total reflection can also be used to store ultracold neutrons but certain problems with storage have not yet been clarified. Slow neutrons can be made to lose speed in a neutron turbine, and come out as ultracold neutrons. A beam of ultracold neutrons could be used in a neutron microscope. (J.S.)

Basic research of neutron radiography using cold neutron beam

International Nuclear Information System (INIS)

Oda, Masahiro; Tamaki, Masayoshi; Tasaka, Kanji

1995-01-01

As the result of demanding high quality images, now the nuclear reactors which can supply stably intense neutron beam have become the most general neutron source for radiography. For the purpose, mostly thermal neutrons have been used, but it is indispensable to use other neutrons than thermal neutrons for advancing neutron radiography technology and expanding the application fields. The radiography using cold neutrons is most behind in the development because the suitable neutron source was not available in Japan. The neutron sources for exclusively obtaining intense cold neutron beam were installed in the Kyoto University reactor in 1986 and in the JRR-3M of Japan Atomic Energy Research Institute in 1991. Basically as neutron energy lowers, the cross section of substances increases. In certain crystalline substances, the Bragg cutoff arises. The removal of scattered neutrons, the measurement of parallelism of beam and the relation of the thickness of objects with the transmissivity of cold neutrons are described. The imaging by TV method and the cold neutron CT in the CNRF and the simplified neutron CT by film method are reported. (K.I.)

Neutron stars as cosmic neutron matter laboratories

International Nuclear Information System (INIS)

Pines, D.

1986-01-01

Recent developments which have radically changed our understanding of the dynamics of neutron star superfluids and the free precession of neutron stars are summarized, and the extent to which neutron stars are cosmic neutron matter laboratories is discussed. 17 refs., 1 tab

Debris flow from 2012 failure of moraine-dammed lake, Three Fingered Jack volcano, Mount Jefferson Wilderness, Oregon

Science.gov (United States)

Sherrod, David R.; Wills, Barton B.

2014-01-01

In the late spring or early summer of 2012, a flood emanated from a small moraine-dammed lake on the northeast flank of Three Fingered Jack in the Mount Jefferson Wilderness. Channel erosion or slope collapse breached the natural dam of the lake, leading to a sudden lowering of lake level by 2.8 m and discharge of 12,700 cubic meters (m3) of water. The resulting debris flow formed a bouldery deposit extending about 0.35 km downslope.

What can zircon ages from the Jack Hills detrital zircon suite really tell us about Hadean geodynamics?

Science.gov (United States)

Whitehouse, Martin; Nemchin, Alexander

2015-04-01

As the only direct sample of the Hadean Earth, detrital zircon grains from the Jack Hills, Western Australia, have been the subject of intense investigation over the almost three decades since their discovery. A wide variety of geochemical and isotopic analyses of these grains, as well as their mineral inclusions, have been used variously to support two fundamentally different models for Hadean geodynamics: (i) Some form of (not necessarily modern-style) plate recycling generating felsic (continental-type?) crust at the boundaries [1, 2], or conversely (ii) the persistence of a long-lived, stagnant basaltic lid within which magmatism occurred as a result of internal temperature perturbations and/or impacts [3, 4], a model also generally consistent with a wide range of observations from post-Hadean geochemical reservoirs. Despite the considerable time and resources expended, the majority of these studies uncritically accept the individual U-Pb zircon ages, even though their veracity is key to many of the interpretations [5, 6]. We report here the results of an in-depth evaluation of all published (and new) U-Pb ages from the Jack Hills zircon suite in order to define age populations that can be used with a high degree of confidence in geodynamic interpretations. A notable problem in the interpretation of U-Pb data from ancient zircon grains (including those as young as the Neoarchean) is that disturbance of the systematics even several 100 Ma after crystallization causes data to spread along the concordia curve without becoming discernably discordant within the relatively large error bounds associated with U/Pb ages from in situ dating methods (e.g. SIMS). While 207Pb/206Pb ages are typically more precise, individually they provide no means to detect Pb-loss-induced younging. However, if two or preferably more analyses have been made in the same zircon growth zone, a reasonable evaluation of the possibility of Pb-loss can be made. In the available Jack Hills zircon

Polarized neutrons

International Nuclear Information System (INIS)

Williams, W.G.

1988-01-01

The book on 'polarized neutrons' is intended to inform researchers in condensed matter physics and chemistry of the diversity of scientific problems that can be investigated using polarized neutron beams. The contents include chapters on:- neutron polarizers and instrumentation, polarized neutron scattering, neutron polarization analysis experiments and precessing neutron polarization. (U.K.)

[Malignant narcissism and sexual homicide--exemplified by the Jack Unterweger case].

Science.gov (United States)

Haller, R

1999-01-01

With the syndrome of malignant narcissism, which is characterised by narcissistic personality disorder, anti-social behaviour, sadism and a marked tendency to paranoid reactions, Kernberg (1985, 1996) describes an independent form of pathological narcissism. According to Stone (1996) this is found in many mass-murderers and serial killers. On the basis of the example of Jack Unterweger the connection between malignant narcissism and sexual offence is discussed as to psychodynamic development, personality structure and psychopathology. Unterweger, who was convicted to lifelong imprisonment in 1976 for sadistic sexual murder, became a wellknown writer in prison and was released prematurely in 1990 as the Austria case of successful rehabilitation. As stated in the sentence passed against him he killed 11 prostitutes in Europe and the USA within the next 18 months, but never pleaded guilty. Psychiatric examination revealed numerous elements of malignant narcissism and the constellation of his development and life was typical of serial offenders.

Neutron spectra produced by moderating an isotopic neutron source

International Nuclear Information System (INIS)

Carrillo Nunnez, Aureliano; Vega Carrillo, Hector Rene

2001-01-01

A Monte Carlo study has been carried out to determine the neutron spectra produced by an isotopic neutron source inserted in moderating media. Most devices used for radiation protection have a response strongly dependent on neutron energy. ISO recommends several neutron sources and monoenergetic neutron radiations, but actual working situations have broad spectral neutron distributions extending from thermal to MeV energies, for instance, near nuclear power plants, medical applications accelerators and cosmic neutrons. To improve the evaluation of the dosimetric quantities, is recommended to calibrate the radiation protection devices in neutron spectra which are nearly like those met in practice. In order to complete the range of neutron calibrating sources, it seems useful to develop several wide spectral distributions representative of typical spectra down to thermal energies. The aim of this investigation was to use an isotopic neutron source in different moderating media to reproduce some of the neutron fields found in practice. MCNP code has been used during calculations, in these a 239PuBe neutron source was inserted in H2O, D2O and polyethylene moderators. Moderators were modeled as spheres and cylinders of different sizes. In the case of cylindrical geometry the anisotropy of resulting neutron spectra was calculated from 0 to 2 . From neutron spectra dosimetric features were calculated. MCNP calculations were validated by measuring the neutron spectra of a 239PuBe neutron source inserted in a H2O cylindrical moderator. The measurements were carried out with a multisphere neutron spectrometer with a 6LiI(Eu) scintillator. From the measurements the neutron spectrum was unfolded using the BUNKIUT code and the UTA4 response matrix. Some of the moderators with the source produce a neutron spectrum close to spectra found in actual applications, then can be used during the calibration of radiation protection devices

Neutron beam design for low intensity neutron and gamma-ray radioscopy using small neutron sources

CERN Document Server

Matsumoto, T

2003-01-01

Two small neutron sources of sup 2 sup 5 sup 2 Cf and sup 2 sup 4 sup 1 Am-Be radioisotopes were used for design of neutron beams applicable to low intensity neutron and gamma ray radioscopy (LINGR). In the design, Monte Carlo code (MCNP) was employed to generate neutron and gamma ray beams suited to LINGR. With a view to variable neutron spectrum and neutron intensity, various arrangements were first examined, and neutron-filter, gamma-ray shield and beam collimator were verified. Monte Carlo calculations indicated that with a suitable filter-shield-collimator arrangement, thermal neutron beam of 3,900 ncm sup - sup 2 s sup - sup 1 with neutron/gamma ratio of 7x10 sup 7 , and 25 ncm sup - sup 2 s sup - sup 1 with very large neutron/gamma ratio, respectively, could be produced by using sup 2 sup 5 sup 2 Cf(122 mu g) and a sup 2 sup 4 sup 1 Am-Be(37GBq)radioisotopes at the irradiation port of 35 cm from the neutron sources.

Neutron cooling and cold-neutron sources (1962); Refroidissement des neutrons et sources de neutrons froids (1962)

Energy Technology Data Exchange (ETDEWEB)

Jacrot, B [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1962-07-01

Intense cold-neutron sources are useful in studying solids by the inelastic scattering of neutrons. The paper presents a general survey covering the following aspects: a) theoretical considerations put forward by various authors regarding thermalization processes at very low temperatures; b) the experiments that have been carried out in numerous laboratories with a view to comparing the different moderators that can be used; c) the cold neutron sources that have actually been produced in reactors up to the present time, and the results obtained with them. (author) [French] Des sources intenses de neutrons froids sont utiles pour l'etude des solides par diffusion inelastique des neutrons. On presente une revue d'ensemble: a) des considerations theoriques faites par divers auteurs sur les processus de thermalisation a tres basse temperature; b) des experiences faites dans de nombreux laboratoires pour comparer les divers moderateurs possibles; c) des sources de neutrons froids effectivement realisees dans des piles a ce jour, et des resultats obtenus avec ces sources. (auteur)

Analýza image produktu Jack Daniel´s Tennessee Fire na českém trhu

OpenAIRE

Papoušek, Jiří

2015-01-01

This Diploma Thesis focuses on a new alcoholic product in the Czech Republic - Jack Daniel's Tennessee Fire. It examines its popularity amongst consumers, its relation to other products in the range of the brand and to the main competitors of the other brands. For better interpretation of the results there is a questionnaire research. The aim of this work is the image analysis of this product in the Czech market and to offer potential recommendations for the brand in the future which come out...

Neutron radiography

International Nuclear Information System (INIS)

Hrdlicka, Z.

1977-01-01

Neutron radiography is a radiographic method using a neutron beam of a defined geometry. The neutron source usually consists of a research reactor, a specialized neutron radiography reactor or the 252 Cf radioisotope source. There are two types of the neutron radiography display system, viz., a system producing neutron radiography images by a photographic process or a system allowing a visual display, eg., using a television monitor. The method can be used wherever X-ray radiography is used except applications in the radiography of humans. The neutron radiography unit at UJV uses the WWR-S reactor as the neutron source and both types of the above mentioned display system. (J.P.)

Neutron matter, neutron pairing, and neutron drops based on chiral effective field theory interactions

Energy Technology Data Exchange (ETDEWEB)

Krueger, Thomas

2016-10-19

The physics of neutron-rich systems is of great interest in nuclear and astrophysics. Precise knowledge of the properties of neutron-rich nuclei is crucial for understanding the synthesis of heavy elements. Infinite neutron matter determines properties of neutron stars, a final stage of heavy stars after a core-collapse supernova. It also provides a unique theoretical laboratory for nuclear forces. Strong interactions are determined by quantum chromodynamics (QCD). However, QCD is non-perturbative at low energies and one presently cannot directly calculate nuclear forces from it. Chiral effective field theory circumvents these problems and connects the symmetries of QCD to nuclear interactions. It naturally and systematically includes many-nucleon forces and gives access to uncertainty estimates. We use chiral interactions throughout all calculation in this thesis. Neutron stars are very extreme objects. The densities in their interior greatly exceed those in nuclei. The exact composition and properties of neutron stars is still unclear but they consist mainly of neutrons. One can explore neutron stars theoretically with calculations of neutron matter. In the inner core of neutron stars exist very high densities and thus maybe exotic phases of matter. To investigate whether there exists a phase transition to such phases even at moderate densities we study the chiral condensate in neutron matter, the order parameter of chiral symmetry breaking, and find no evidence for a phase transition at nuclear densities. We also calculate the more extreme system of spin-polarised neutron matter. With this we address the question whether there exists such a polarised phase in neutron stars and also provide a benchmark system for lattice QCD. We find spin-polarised neutron matter to be an almost non-interacting Fermi gas. To understand the cooling of neutron stars neutron pairing is of great importance. Due to the high densities especially triplet pairing is of interest. We

The Los Alamos Neutron Science Center Spallation Neutron Sources

International Nuclear Information System (INIS)

Nowicki, Suzanne F.; Wender, Stephen A.; Mocko, Michael

2017-01-01

The Los Alamos Neutron Science Center (LANSCE) provides the scientific community with intense sources of neutrons, which can be used to perform experiments supporting civilian and national security research. These measurements include nuclear physics experiments for the defense program, basic science, and the radiation effect programs. This paper focuses on the radiation effects program, which involves mostly accelerated testing of semiconductor parts. When cosmic rays strike the earth's atmosphere, they cause nuclear reactions with elements in the air and produce a wide range of energetic particles. Because neutrons are uncharged, they can reach aircraft altitudes and sea level. These neutrons are thought to be the most important threat to semiconductor devices and integrated circuits. The best way to determine the failure rate due to these neutrons is to measure the failure rate in a neutron source that has the same spectrum as those produced by cosmic rays. Los Alamos has a high-energy and a low-energy neutron source for semiconductor testing. Both are driven by the 800-MeV proton beam from the LANSCE accelerator. The high-energy neutron source at the Weapons Neutron Research (WNR) facility uses a bare target that is designed to produce fast neutrons with energies from 100 keV to almost 800 MeV. The measured neutron energy distribution from WNR is very similar to that of the cosmic-ray-induced neutrons in the atmosphere. However, the flux provided at the WNR facility is typically 5×107 times more intense than the flux of the cosmic-ray-induced neutrons. This intense neutron flux allows testing at greatly accelerated rates. An irradiation test of less than an hour is equivalent to many years of neutron exposure due to cosmic-ray neutrons. The low-energy neutron source is located at the Lujan Neutron Scattering Center. It is based on a moderated source that provides useful neutrons from subthermal energies to ~100 keV. The characteristics of these sources

The Los Alamos Neutron Science Center Spallation Neutron Sources

Science.gov (United States)

Nowicki, Suzanne F.; Wender, Stephen A.; Mocko, Michael

The Los Alamos Neutron Science Center (LANSCE) provides the scientific community with intense sources of neutrons, which can be used to perform experiments supporting civilian and national security research. These measurements include nuclear physics experiments for the defense program, basic science, and the radiation effect programs. This paper focuses on the radiation effects program, which involves mostly accelerated testing of semiconductor parts. When cosmic rays strike the earth's atmosphere, they cause nuclear reactions with elements in the air and produce a wide range of energetic particles. Because neutrons are uncharged, they can reach aircraft altitudes and sea level. These neutrons are thought to be the most important threat to semiconductor devices and integrated circuits. The best way to determine the failure rate due to these neutrons is to measure the failure rate in a neutron source that has the same spectrum as those produced by cosmic rays. Los Alamos has a high-energy and a low-energy neutron source for semiconductor testing. Both are driven by the 800-MeV proton beam from the LANSCE accelerator. The high-energy neutron source at the Weapons Neutron Research (WNR) facility uses a bare target that is designed to produce fast neutrons with energies from 100 keV to almost 800 MeV. The measured neutron energy distribution from WNR is very similar to that of the cosmic-ray-induced neutrons in the atmosphere. However, the flux provided at the WNR facility is typically 5×107 times more intense than the flux of the cosmic-ray-induced neutrons. This intense neutron flux allows testing at greatly accelerated rates. An irradiation test of less than an hour is equivalent to many years of neutron exposure due to cosmic-ray neutrons. The low-energy neutron source is located at the Lujan Neutron Scattering Center. It is based on a moderated source that provides useful neutrons from subthermal energies to ∼100 keV. The characteristics of these sources, and

Workshop on polarized neutron filters and polarized pulsed neutron experiments

International Nuclear Information System (INIS)

Itoh, Shinichi

2004-07-01

The workshop was held in KEK by thirty-three participants on April 26, 2004. The polarized neutron filter method was only discussed. It consists of three parts; the first part was discussed on the polarized neutron methods, the second part on the polarized neutron experiments and the third on the pulse neutron spectrometer and polarized neutron experiments. The six papers were presented such as the polarized 3 He neutron spin filter, neutron polarization by proton polarized filter, soft master and neutron scattering, polarized neutron in solid physics, polarization experiments by chopper spectroscope and neutron polarization system in superHRPD. (S.Y.)

Neutron matter, symmetry energy and neutron stars

Energy Technology Data Exchange (ETDEWEB)

Stefano, Gandolfi [Los Alamos National Laboratory (LANL); Steiner, Andrew W [ORNL

2016-01-01

Recent progress in quantum Monte Carlo with modern nucleon-nucleon interactions have enabled the successful description of properties of light nuclei and neutron-rich matter. Of particular interest is the nuclear symmetry energy, the energy cost of creating an isospin asymmetry, and its connection to the structure of neutron stars. Combining these advances with recent observations of neutron star masses and radii gives insight into the equation of state of neutron-rich matter near and above the saturation density. In particular, neutron star radius measurements constrain the derivative of the symmetry energy.

Fail-safe neutron shutter used for thermal neutron radiography

International Nuclear Information System (INIS)

Sachs, R.D.; Morris, R.A.

1976-11-01

A fail-safe, reliable, easy-to-use neutron shutter was designed, built, and put into operation at the Omega West Reactor, Los Alamos Scientific Laboratory. The neutron shutter will be used primarily to perform thermal neutron radiography, but is also available for a highly collimated source of thermal neutrons [neutron flux = 3.876 x 10 6 (neutrons)/(cm 2 .s)]. Neutron collimator sizes of either 10.16 by 10.16 cm or 10.16 by 30.48 cm are available

Extraction of the neutron-neutron scattering length ann from kinematically complete neutron-deuteron breakup experiments

International Nuclear Information System (INIS)

Witala, H.; Hueber, D.; Gloeckle, W.; Tornow, W.; Gonzalez Trotter, D.E.

1996-01-01

Data for the neutron-neutron final-state-interaction cross section obtained recently in a kinematically complete neutron-deuteron breakup experiment have been reanalyzed using rigorous solutions of the three-nucleon Faddeev equations with realistic nucleon-nucleon interactions. A discrepancy was found with respect to a recent analysis based on the W-matrix approximation to the Paris potential. We also estimate theoretical uncertainties in extracting the neutron-neutron scattering length resulting from the use of different nucleon-nucleon interactions and the possible action of the two pion-exchange three-nucleon force. We find that there exists a certain production angle for the interacting neutron-neutron pair where the uncertainties become minimal. (author)

Neutron Absorbing Ability Variation in Neutron Absorbing Material Caused by the Neutron Irradiation in Spent Fuel Storage Facility

Energy Technology Data Exchange (ETDEWEB)

Sohn, Hee Dong; Han, Seul Gi; Lee, Sang Dong; Kim, Ki Hong; Ryu, Eag Hyang; Park, Hwa Gyu [Doosan Heavy Industries and Construction, Changwon (Korea, Republic of)

2014-10-15

In spent fuel storage facility like high density spent fuel storage racks and dry storage casks, spent fuels are stored with neutron absorbing materials installed as a part of those facilities, and they are used for absorbing neutrons emitted from spent fuels. Usually structural material with neutron absorbing material of racks and casks are located around spent fuels, so it is irradiated by neutrons for long time. Neutron absorbing ability could be changed by the variation of nuclide composition in neutron absorbing material caused by the irradiation of neutrons. So, neutron absorbing materials are continuously faced with spent fuels with boric acid solution or inert gas environment. Major nuclides in neutron absorbing material are Al{sup 27}, C{sup 12}, B{sup 11}, B{sup 10} and they are changed to numerous other ones as radioactive decay or neutron absorption reaction. The B{sup 10} content in neutron absorbing material dominates the neutron absorbing ability, so, the variation of nuclide composition including the decrease of B{sup 10} content is the critical factor on neutron absorbing ability. In this study, neutron flux in spent fuel, the activation of neutron absorbing material and the variation of nuclide composition are calculated. And, the minimum neutron flux causing the decrease of B{sup 10} content is calculated in spent fuel storage facility. Finally, the variation of neutron multiplication factor is identified according to the one of B{sup 10} content in neutron absorbing material. The minimum neutron flux to impact the neutron absorbing ability is 10{sup 10} order, however, usual neutron flux from spent fuel is 10{sup 8} order. Therefore, even though neutron absorbing material is irradiated for over 40 years, B{sup 10} content is little decreased, so, initial neutron absorbing ability could be kept continuously.

Neutron optics using transverse field neutron spin echo method

International Nuclear Information System (INIS)

Achiwa, Norio; Hino, Masahiro; Yamauchi, Yoshihiro; Takakura, Hiroyuki; Tasaki, Seiji; Akiyoshi, Tsunekazu; Ebisawa, Toru.

1993-01-01

A neutron spin echo (NSE) spectrometer with perpendicular magnetic field to the neutron scattering plane, using an iron yoke type electro-magnet has been developed. A combination of cold neutron guider, supermirror neutron polarizer of double reflection type and supermirror neutron analyser was adopted for the spectrometer. The first application of the NSE spectrometer to neutron optics by passing Larmor precessing neutrons through gas, solid and liquid materials of several different lengths which are inserted in one of the precession field have been examined. Preliminary NSE spectra of this sample geometry are discussed. (author)

Neutron radiography

International Nuclear Information System (INIS)

Hiraoka, Eiichi

1988-01-01

The thermal neutron absorption coefficient is essentially different from the X-ray absorption coefficient. Each substance has a characteristic absorption coefficient regardless of its density. Neutron deams have the following features: (1) neutrons are not transmitted efficiently by low molecular weight substances, (2) they are transmitted efficiently by heavy metals, and (3) the transmittance differs among isotopes. Thus, neutron beams are suitable for cheking for foreign matters in heavy metals and testing of composites consisting of both heavy and light materials. A neutron source generates fast neutrons, which should be converted into thermal neutrons by reducing their energy. Major neutron souces include nuclear reactors, radioisotopes and particle accelerators. Photographic films and television systems are mainly used to observe neutron transmission images. Computers are employed for image processing, computerized tomography and three-dimensional analysis. The major applications of neutron radiography include inspection of neclear fuel; evaluation of material for airplane; observation of fuel in the engine and oil in the hydraulic systems in airplanes; testing of composite materials; etc. (Nogami, K.)

Neutron Dosimetry

International Nuclear Information System (INIS)

Vanhavere, F.

2001-01-01

The objective of SCK-CEN's R and D programme on neutron dosimetry is to improve the determination of neutron doses by studying neutron spectra, neutron dosemeters and shielding adaptations. In 2000, R and D focused on the contiued investigation of the bubble detectors type BD-PND and BDT, in particular their sensitivity and temperature dependence; the updating of SCK-CEN's criticality dosemeter, the investigation of the characteristics of new thermoluminescent materials and their use in neutron dosemetry; and the investigation of neutron shielding

Neutron Dosimetry

Energy Technology Data Exchange (ETDEWEB)

Vanhavere, F

2001-04-01

The objective of SCK-CEN's R and D programme on neutron dosimetry is to improve the determination of neutron doses by studying neutron spectra, neutron dosemeters and shielding adaptations. In 2000, R and D focused on the contiued investigation of the bubble detectors type BD-PND and BDT, in particular their sensitivity and temperature dependence; the updating of SCK-CEN's criticality dosemeter, the investigation of the characteristics of new thermoluminescent materials and their use in neutron dosemetry; and the investigation of neutron shielding.

Neutronic analysis of JET external neutron monitor response

Energy Technology Data Exchange (ETDEWEB)

Snoj, Luka, E-mail: luka.snoj@ijs.si [Reactor Physics Division, Jožef Stefan Institute, Jamova cesta 39, SI-1000 Ljubljana (Slovenia); Lengar, Igor; Čufar, Aljaž [Reactor Physics Division, Jožef Stefan Institute, Jamova cesta 39, SI-1000 Ljubljana (Slovenia); Syme, Brian; Popovichev, Sergey [Culham Centre for Fusion Energy, Culham Science Centre, Abingdon, OX14 3DB, United Kingdom (United Kingdom); Batistoni, Paola [ENEA C. R. Frascati, via E. Fermi 45, 00044 Frascati, Roma (Italy); Conroy, Sean [VR Association, Uppsala University, Department of Physics and Astronomy, PO Box 516, SE-75120 Uppsala (Sweden)

2016-11-01

Highlights: • We model JET tokamak containing JET remote handling system. • We investigate effect of remote handling system on external neutron monitor response. • Remote handling system correction factors are calculated. • Integral correction factors are relatively small, i.e up to 8%. - Abstract: The power output of fusion devices is measured in terms of the neutron yield which relates directly to the fusion yield. JET made a transition from Carbon wall to ITER-Like Wall (Beryllium/Tungsten/Carbon) during 2010–11. Absolutely calibrated measurement of the neutron yield by JET neutron monitors was ensured by direct measurements using a calibrated {sup 252}Cf neutron source (NS) deployed by the in-vessel remote handling system (RHS) inside the JET vacuum vessel. Neutronic calculations were required in order to understand the neutron transport from the source in the vacuum vessel to the fission chamber detectors mounted outside the vessel on the transformer limbs of the tokamak. We developed a simplified computational model of JET and the JET RHS in Monte Carlo neutron transport code MCNP and analyzed the paths and structures through which neutrons reach the detectors and the effect of the JET RHS on the neutron monitor response. In addition we performed several sensitivity studies of the effect of substantial massive structures blocking the ports on the external neutron monitor response. As the simplified model provided a qualitative picture of the process only, some calculations were repeated using a more detailed full 3D model of the JET tokamak.

Investigation of Response of Several Neutron Surveymeters by a DT Neutron Generator

International Nuclear Information System (INIS)

Kim, Sang In; Jang, In Su; Kim, Jang Lyul; Lee, Jung IL; Kim, Bong Hwan

2012-01-01

Several neutron measuring devices were tested under the neutron fields characterized with two distinct kinds of thermal and fast neutron spectrum. These neutron fields were constructed by the mixing of both thermal neutron fields and fast neutron fields. The thermal neutron field was constructed using by a graphite pile with eight AmBe neutron sources. The fast neutron field of 14 MeV was made by a DT neutron generator. In order to change the fraction of fast neutron fluence rate in each neutron fields, a neutron generator was placed in the thermal neutron field at 50 cm and 150 cm from the reference position. The polyethylene neutron collimator was used to make moderated 14 MeV neutron field. These neutron spectra were measured by using a Bonner sphere system with an LiI scintillator, and dosimetric quantities delivered to neutron surveymeters were determined from these measurement results.

Neutron Imaging at Compact Accelerator-Driven Neutron Sources in Japan

Directory of Open Access Journals (Sweden)

Yoshiaki Kiyanagi

2018-03-01

Full Text Available Neutron imaging has been recognized to be very useful to investigate inside of materials and products that cannot be seen by X-ray. New imaging methods using the pulsed structure of neutron sources based on accelerators has been developed also at compact accelerator-driven neutron sources and opened new application fields in neutron imaging. The world’s first dedicated imaging instrument at pulsed neutron sources was constructed at J-PARC in Japan owing to the development of such new methods. Then, usefulness of the compact accelerator-driven neutron sources in neutron science was recognized and such facilities were newly constructed in Japan. Now, existing and new sources have been used for neutron imaging. Traditional imaging and newly developed pulsed neutron imaging such as Bragg edge transmission have been applied to various fields by using compact and large neutron facilities. Here, compact accelerator-driven neutron sources used for imaging in Japan are introduced and some of their activities are presented.

Accelerator based neutron source for neutron capture therapy

International Nuclear Information System (INIS)

Salimov, R.; Bayanov, B.; Belchenko, Yu.; Belov, V.; Davydenko, V.; Donin, A.; Dranichnikov, A.; Ivanov, A.; Kandaurov, I; Kraynov, G.; Krivenko, A.; Kudryavtsev, A.; Kursanov, N.; Savkin, V.; Shirokov, V.; Sorokin, I.; Taskaev, S.; Tiunov, M.

2004-01-01

Full text: The Budker Institute of Nuclear Physics (Novosibirsk) and the Institute of Physics and Power Engineering (Obninsk) have proposed an accelerator based neutron source for neutron capture and fast neutron therapy for hospital. Innovative approach is based upon vacuum insulation tandem accelerator (VITA) and near threshold 7 Li(p,n) 7 Be neutron generation. Pilot accelerator based neutron source for neutron capture therapy is under construction now at the Budker Institute of Nuclear Physics, Novosibirsk, Russia. In the present report, the pilot facility design is presented and discussed. Design features of facility components are discussed. Results of experiments and simulations are presented. Complete experimental tests are planned by the end of the year 2005

Design of hyper-thermal neutron irradiation fields for neutron capture therapy in KUR-heavy water neutron irradiation facility. Mounting of hyper-thermal neutron converter in therapeutic collimator

International Nuclear Information System (INIS)

Sakurai, Y.; Kobayashi, T.

2001-01-01

Neutron capture therapy (NCP) using thermal neutron needs to improve of depth dose distribution in a living body. Epi-thermal neutron following moderation of fast neutron is usually used for improving of the depth dose distribution. The moderation method of fast neutron, however, gets mixed some of high energy neutron which give some of serious effects to a living body, and involves the difficulty for collimation of thermal neutron to the diseased part. Hyper-thermal neutrons, which are in an energy range of 0.1-3 eV at high temperature side of thermal neutron, are under consideration for application to the NCP. The hyper-thermal neutrons can be produced by up-scattering of thermal neutron in a high temperature material. Fast neutron components in collimator for the NCP reduce on application of the up-scattering method. Graphite at high temperature (>1000k) is used as a hyper-thermal neutron converter. The hyper-thermal neutron converter is planted to mount on therapeutic collimator which is located at the nearest side of patient for the NCP. Total neutron flux, ratio of hyper-thermal neutron to total neutron, and ratio of gamma-ray dose to neutron flux are calculated as a function of thickness of the graphite converter using monte carlo code MCNP-V4B. (M. Suetake)

The secondary neutron sources for generation of particular neutron fluxes

International Nuclear Information System (INIS)

Tracz, G.

2007-07-01

The foregoing paper presents the doctor's thesis entitled '' The secondary neutron sources for generation of particular neutron fluxes ''. Two secondary neutron sources have been designed, which exploit already existing primary sources emitting neutrons of energies different from the desired ones. The first source is devoted to boron-neutron capture therapy (BNCT). The research reactor MARIA at the Institute of Atomic Energy in Swierk (Poland) is the primary source of the reactor thermal neutrons, while the secondary source should supply epithermal neutrons. The other secondary source is the pulsed source of thermal neutrons that uses fast 14 MeV neutrons from a pulsed generator at the Institute of Nuclear Physics PAN in Krakow (Poland). The physical problems to be solved in the two mentioned cases are different. Namely, in order to devise the BNCT source the initial energy of particles ought to be increased, whilst in the other case the fast neutrons have to be moderated. Slowing down of neutrons is relatively easy since these particles lose energy when they scatter in media; the most effective moderators are the materials which contain light elements (mostly hydrogen). In order to increase the energy of neutrons from thermal to epithermal (the BNCT case) the so-called neutron converter should be exploited. It contains a fissile material, 235 U. The thermal neutrons from the reactor cause fission of uranium and fast neutrons are emitted from the converter. Then fissile neutrons of energy of a few MeV are slowed down to the required epithermal energy range. The design of both secondary sources have been conducted by means of Monte Carlo simulations, which have been carried out using the MCNP code. In the case of the secondary pulsed thermal neutron source, some of the calculated results have been verified experimentally. (author)

Evapotranspiration and crop coefficients of corn in monoculture and intercropped with jack bean

Directory of Open Access Journals (Sweden)

Mário S. P. de Araújo

Full Text Available ABSTRACT This study was carried out to determine the evapotranspiration (ETc and crop coefficients (Kc for four stages of “Caatingueiro” corn under the climate condition of Seropédica, RJ, Brazil, using weighing lysimeters. The field trial occurred in 2015, from March 18 to June 25, in two areas cultivated with “Caatingueiro’ corn intercropped with jack bean and in monoculture. The reference evapotranspiration (ETo was estimated by the FAO-56 Penman-Monteith model and the Kc values were determined by the ratio between ETc and ETo. The Kc values obtained for the intercropping and monoculture systems, were respectively: 0.78 (I; 1.01 (II; 1.10 (III and 1.01 (IV, and 0.62 (I; 0.92 (II; 1.27 (III and 0.81 (IV, and they were different from the values presented by FAO.

Tongkat Ali (Eurycoma longifolia Jack): a review on its ethnobotany and pharmacological importance.

Science.gov (United States)

Bhat, Rajeev; Karim, A A

2010-10-01

Eurycoma longifolia Jack is an herbal medicinal plant of South-East Asian origin, popularly recognized as 'Tongkat Ali.' The plant parts have been traditionally used for its antimalarial, aphrodisiac, anti-diabetic, antimicrobial and anti-pyretic activities, which have also been proved scientifically. The plant parts are rich in various bioactive compounds (like eurycomaoside, eurycolactone, eurycomalactone, eurycomanone, and pasakbumin-B) among which the alkaloids and quassinoids form a major portion. Even though toxicity and safety evaluation studies have been pursued, still a major gap exists in providing scientific base for commercial utilization and clearance of the Tongkat Ali products with regard to consumer's safety. The present review aims at reviewing the research works undertaken till date, on this plant in order to provide sufficient baseline information for future works and for commercial exploitation. Copyright © 2010 Elsevier B.V. All rights reserved.

Safe jack-up method permits repairs of tank bottoms and foundations

International Nuclear Information System (INIS)

de Wit, J.

1991-01-01

The oil and chemical industries use many thousands of steel tanks to store crude oil, oil products, and chemical liquids. The majority of these tanks are 30-40 years old. Tank bottoms are likely to begin leaking in the coming years, as these tanks get older. The European technique of jacking up a tank and repairing its foundation allows the thorough inspection of the underside of the tank bottom and the removal of saturated foundation material. And the possibility of soil and groundwater pollution is reduced to a minimum. With good, regular maintenance, the lifetime of a storage tank is very long. But experience has shown that special attention should be paid to the tank's bottom. Tank bottoms are only 5 or 6 mm thick, and in the last 10 years, an increasing number of leaks in tank bottoms have been reported. Tank foundations are affected by these leaks. This article describes the resulting procedure, which is used successfully in many European countries, but is not yet common in the U.S

Calculations to support JET neutron yield calibration: Modelling of neutron emission from a compact DT neutron generator

Science.gov (United States)

Čufar, Aljaž; Batistoni, Paola; Conroy, Sean; Ghani, Zamir; Lengar, Igor; Milocco, Alberto; Packer, Lee; Pillon, Mario; Popovichev, Sergey; Snoj, Luka; JET Contributors

2017-03-01

At the Joint European Torus (JET) the ex-vessel fission chambers and in-vessel activation detectors are used as the neutron production rate and neutron yield monitors respectively. In order to ensure that these detectors produce accurate measurements they need to be experimentally calibrated. A new calibration of neutron detectors to 14 MeV neutrons, resulting from deuterium-tritium (DT) plasmas, is planned at JET using a compact accelerator based neutron generator (NG) in which a D/T beam impinges on a solid target containing T/D, producing neutrons by DT fusion reactions. This paper presents the analysis that was performed to model the neutron source characteristics in terms of energy spectrum, angle-energy distribution and the effect of the neutron generator geometry. Different codes capable of simulating the accelerator based DT neutron sources are compared and sensitivities to uncertainties in the generator's internal structure analysed. The analysis was performed to support preparation to the experimental measurements performed to characterize the NG as a calibration source. Further extensive neutronics analyses, performed with this model of the NG, will be needed to support the neutron calibration experiments and take into account various differences between the calibration experiment and experiments using the plasma as a source of neutrons.

Calculations to support JET neutron yield calibration: Modelling of neutron emission from a compact DT neutron generator

Energy Technology Data Exchange (ETDEWEB)

Čufar, Aljaž, E-mail: aljaz.cufar@ijs.si [Reactor Physics Department, Jožef Stefan Institute, Jamova cesta 39, SI-1000 Ljubljana (Slovenia); EUROfusion Consortium, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Batistoni, Paola [ENEA, Department of Fusion and Nuclear Safety Technology, I-00044 Frascati, Rome (Italy); EUROfusion Consortium, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Conroy, Sean [Uppsala University, Department of Physics and Astronomy, PO Box 516, SE-75120 Uppsala (Sweden); EUROfusion Consortium, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Ghani, Zamir [Culham Centre for Fusion Energy, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); EUROfusion Consortium, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Lengar, Igor [Reactor Physics Department, Jožef Stefan Institute, Jamova cesta 39, SI-1000 Ljubljana (Slovenia); EUROfusion Consortium, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Milocco, Alberto; Packer, Lee [Culham Centre for Fusion Energy, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); EUROfusion Consortium, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Pillon, Mario [ENEA, Department of Fusion and Nuclear Safety Technology, I-00044 Frascati, Rome (Italy); EUROfusion Consortium, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Popovichev, Sergey [Culham Centre for Fusion Energy, Culham Science Centre, Abingdon OX14 3DB (United Kingdom); EUROfusion Consortium, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Snoj, Luka [Reactor Physics Department, Jožef Stefan Institute, Jamova cesta 39, SI-1000 Ljubljana (Slovenia); EUROfusion Consortium, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom)

2017-03-01

At the Joint European Torus (JET) the ex-vessel fission chambers and in-vessel activation detectors are used as the neutron production rate and neutron yield monitors respectively. In order to ensure that these detectors produce accurate measurements they need to be experimentally calibrated. A new calibration of neutron detectors to 14 MeV neutrons, resulting from deuterium–tritium (DT) plasmas, is planned at JET using a compact accelerator based neutron generator (NG) in which a D/T beam impinges on a solid target containing T/D, producing neutrons by DT fusion reactions. This paper presents the analysis that was performed to model the neutron source characteristics in terms of energy spectrum, angle–energy distribution and the effect of the neutron generator geometry. Different codes capable of simulating the accelerator based DT neutron sources are compared and sensitivities to uncertainties in the generator's internal structure analysed. The analysis was performed to support preparation to the experimental measurements performed to characterize the NG as a calibration source. Further extensive neutronics analyses, performed with this model of the NG, will be needed to support the neutron calibration experiments and take into account various differences between the calibration experiment and experiments using the plasma as a source of neutrons.

Study of neutron fields around an intense neutron generator.

Science.gov (United States)

Kicka, L; Machrafi, R; Miller, A

2017-12-01

Neutron fields in the vicinity of the newly built neutron facility, at the University of Ontario Institute of Technology (UOIT), have been investigated in a series of Monte Carlo simulations and measurements. The facility hosts a P-385 neutron generator based on a deuterium-deuterium fusion reaction. The neutron fluence at different locations around the neutron generator facility has been simulated using MCNPX 2.7E Monte Carlo particle transport program. To characterize neutron fields, three neutron sources were modeled with distributions corresponding to different incident deuteron energies of 90kV, 110kV, and 130kV. Measurements have been carried out to determine the dose rate at locations adjacent to the generator using bubble detectors (BDs). The neutron intensity was evaluated and the total dose rates corresponding to different applied acceleration potentials were estimated at various locations. Copyright © 2017 Elsevier Ltd. All rights reserved.

Miscellaneous neutron techniques

International Nuclear Information System (INIS)

Iddings, F.A.

1976-01-01

Attention is brought to the less often uses of neutrons in the areas of neutron radiography, well logging, and neutron gaging. Emphasis on neutron radiography points toward the isotopic sensitivity of the method versus the classical bulk applications. Also recognized is the ability of neutron radiography to produce image changes that correspond to thickness and density changes obtained in photon radiography. Similarly, neutron gaging applications center on the measurement of radiography. Similarly, neutron gaging applications center on the measurement of water, oil, or plastics in industrial samples. Well logging extends the neutron gaging to encompass many neutron properties and reactions besides thermalization and capture. Neutron gaging also gives information on organic structure and concentrations of a variety of elements or specific compounds in selected matrices

Discovery of the neutron (to the fiftieth anniversary of neutron discovery)

International Nuclear Information System (INIS)

Pasechnik, M.V.

1984-01-01

Development of neutron physics in the USSR for the recent 50 years from the moment of neutron discovery is considered. History of neutron discovery is presented in brief. Neutron properties and fundamental problems of physics: electric dipole neutron moment, neutron β-decay, neutron interaction with nuclei and potential of nucleon interaction not conserving spatial parity are discussed. Main aspects of neutron physics application in power engineering, nuclear technology and other branches of science and technique are set forth

Neutron rich matter, neutron stars, and their crusts

International Nuclear Information System (INIS)

Horowitz, C J

2011-01-01

Neutron rich matter is at the heart of many fundamental questions in Nuclear Physics and Astrophysics. What are the high density phases of QCD? Where did the chemical elements come from? What is the structure of many compact and energetic objects in the heavens, and what determines their electromagnetic, neutrino, and gravitational-wave radiations? Moreover, neutron rich matter is being studied with an extraordinary variety of new tools such as Facility for Rare Isotope Beams (FRIB) and the Laser Interferometer Gravitational Wave Observatory (LIGO). We describe the Lead Radius Experiment (PREX) that is using parity violation to measure the neutron radius in 208Pb. This has important implications for neutron stars and their crusts. Using large scale molecular dynamics, we model the formation of solids in both white dwarfs and neutron stars. We find neutron star crust to be the strongest material known, some 10 billion times stronger than steel. It can support mountains on rotating neutron stars large enough to generate detectable gravitational waves. Finally, we describe a new equation of state for supernova and neutron star merger simulations based on the Virial expansion at low densities, and large scale relativistic mean field calculations.

Neutron Beam Filters

International Nuclear Information System (INIS)

Adib, M.

2011-01-01

The purpose of filters is to transmit neutrons with selected energy, while remove unwanted ones from the incident neutron beam. This reduces the background, and the number of spurious. The types of commonly used now-a-day neutron filters and their properties are discussed in the present work. There are three major types of neutron filters. The first type is filter of selective thermal neutron. It transmits the main reflected neutrons from a crystal monochromate, while reject the higher order contaminations accompanying the main one. Beams coming from the moderator always contain unwanted radiation like fast neutrons and gamma-rays which contribute to experimental background and to the biological hazard potential. Such filter type is called filter of whole thermal neutron spectrum. The third filter type is it transmits neutrons with energies in the resonance energy range (En . 1 KeV). The main idea of such neutron filter technique is the use of large quantities of a certain material which have the deep interference minima in its total neutron cross-section. By transmitting reactor neutrons through bulk layer of such material, one can obtain the quasimonochromatic neutron lines instead of white reactor spectrum.

Comparative toxic effects of some xenobiotics on the germination and early seedling growth of jack pine (Pinus banksiana Lamb. ) and white birch (Betula papyrifera Marsh. )

Energy Technology Data Exchange (ETDEWEB)

Weinberger, P; Vladut, R

1981-12-01

Seeds of jack pine (Pinus banksiana Lamb.) and white birch (Betula papyrifera Marsh.) were germinated in homogeneous emulsions or aqueous tank-mix solutions of fenitrothion or Matacil and their respective adjuvants: Atlox and Aerotex, or diluent oil No. 585 and nonylphenol. Percentage and peak germination values, water uptake, sprout length, ATP content, and morphological modifications were recorded from 0 to 14 or 21 days. Apart from 100 ppm fenitrothion which stimulated germination values, germination in jack pine was only marginally affected by any of the treatments; in contrast, white birch was negatively affected by all treatments. The most sensitive parameters of toxicity were the sprout length and ATP content after 14 days growth. Aberrant hypocotyl/root length ratios were evidenced in pine seeds after exposure to xenobiotic treatments which did not affect the germinative capacity of seeds. ATP content in the 14-day-old pine and birch seedlings was consistently higher than controls in all treatment sets. (Refs. 29).

Chemical composition of the leaf essential oils of Murraya koenigii (L. Spreng and Murraya paniculata (L. Jack

Directory of Open Access Journals (Sweden)

Jasim Uddin Chowdhury

2008-06-01

Full Text Available The chemical composition of the leaf oils of Murraya koenigii (L. Spreng and M. paniculata (L. Jack from Bangladesh was studied by gas chromatography mass spectroscopy (GC-MS. M. koenigii oil contained 39 compounds of which the major is 3-carene (54.2% followed by caryophyllene (9.5%. Oil of M. paniculata contained 58 compounds of which the major are caryophyllene oxide (16.6%, b-caryophyllene (11.8%, spathulenol (10.2%, b-elemene (8.9%, germacrene D (6.9% and cyclooctene, 4-methylene-6-(1-propenylidene (6.4%. The compositions of both oils varied qualitatively and quantitatively.

Chemical composition of the leaf essential oils of Murraya koenigii (L. Spreng and Murraya paniculata (L. Jack

Directory of Open Access Journals (Sweden)

Jasim Uddin Chowdhury

2008-12-01

Full Text Available The chemical composition of the leaf oils of Murraya koenigii (L. Spreng and M. paniculata (L. Jack from Bangladesh was studied by gas chromatography mass spectroscopy (GC-MS. M. koenigii oil contained 39 compounds of which the major is 3-carene (54.2% followed by caryophyllene (9.5%. Oil of M. paniculata contained 58 compounds of which the major are caryophyllene oxide (16.6%, beta-caryophyllene (11.8%, spathulenol (10.2%, beta-elemene (8.9%, germacrene D (6.9% and cyclooctene, 4-methylene-6-(1-propenylidene (6.4%. The composi-tions of both oils varied qualitatively and quantitatively.

Neutron stochastic transport theory with delayed neutrons

International Nuclear Information System (INIS)

Munoz-Cobo, J.L.; Verdu, G.

1987-01-01

From the stochastic transport theory with delayed neutrons, the Boltzmann transport equation with delayed neutrons for the average flux emerges in a natural way without recourse to any approximation. From this theory a general expression is obtained for the Feynman Y-function when delayed neutrons are included. The single mode approximation for the particular case of a subcritical assembly is developed, and it is shown that Y-function reduces to the familiar expression quoted in many books, when delayed neutrons are not considered, and spatial and source effects are not included. (author)

Geohydrologic Investigations and Landscape Characteristics of Areas Contributing Water to Springs, the Current River, and Jacks Fork, Ozark National Scenic Riverways, Missouri

Science.gov (United States)

Mugel, Douglas N.; Richards, Joseph M.; Schumacher, John G.

2009-01-01

The Ozark National Scenic Riverways (ONSR) is a narrow corridor that stretches for approximately 134 miles along the Current River and Jacks Fork in southern Missouri. Most of the water flowing in the Current River and Jacks Fork is discharged to the rivers from springs within the ONSR, and most of the recharge area of these springs is outside the ONSR. This report describes geohydrologic investigations and landscape characteristics of areas contributing water to springs and the Current River and Jacks Fork in the ONSR. The potentiometric-surface map of the study area for 2000-07 shows that the groundwater divide extends beyond the surface-water divide in some places, notably along Logan Creek and the northeastern part of the study area, indicating interbasin transfer of groundwater between surface-water basins. A low hydraulic gradient occurs in much of the upland area west of the Current River associated with areas of high sinkhole density, which indicates the presence of a network of subsurface karst conduits. The results of a low base-flow seepage run indicate that most of the discharge in the Current River and Jacks Fork was from identified springs, and a smaller amount was from tributaries whose discharge probably originated as spring discharge, or from springs or diffuse groundwater discharge in the streambed. Results of a temperature profile conducted on an 85-mile reach of the Current River indicate that the lowest average temperatures were within or downstream from inflows of springs. A mass-balance on heat calculation of the discharge of Bass Rock Spring, a previously undescribed spring, resulted in an estimated discharge of 34.1 cubic feet per second (ft3/s), making it the sixth largest spring in the Current River Basin. The 13 springs in the study area for which recharge areas have been estimated accounted for 82 percent (867 ft3/s of 1,060 ft3/s) of the discharge of the Current River at Big Spring during the 2006 seepage run. Including discharge from

Fundamental of neutron radiography and the present of neutron radiography in Japan

International Nuclear Information System (INIS)

Sekita, Junichiro

1988-01-01

Neutron radiography refers to the application of transmitted neutrons to analysis. In general, thermal neutron is used for neutron radiography. Thermal neutron is easily absorbed by light atoms, including hydrogen, boron and lithium, while it is not easily absorbed by such heavy atoms as tungsten, lead and uranium, permitting detection of impurities in heavy metals. Other neutrons than thermal neutron can also be applied. Cold neutron is produced from fast neutron using a moderator to reduce its energy down to below that of thermal neutron. Cold neutron is usefull for analysis of thick material. Epithermal neutron can induce resonance characteristic of each substance. With a relatively small reaction area, fast neutron permits observation of thick samples. Being electrically neutral, neutrons are difficult to detect by direct means. Thus a substance that releases charged particles is put in the path of neutrons for indirect measurement. X-ray film combined with converter screen for conversion of neutrons to charge particles is placed behind the sample. Photographing is carried out by a procedure similar to X-ray photography. Major institues and laboratories in Japan provided with neutron radiography facilities are listed. (Nogami, K.)

Review of Non-Neutron and Neutron Nuclear Data, 2004

International Nuclear Information System (INIS)

Holden, Norman E.

2005-01-01

Review articles are in preparation for the 2004 edition of the CRC Handbook of Chemistry and Physics dealing with the evaluation of both non-neutron and neutron nuclear data. Data on the discovery of element 110, Darmstadtium, and element 111 have been officially accepted, while data on element 118 have been withdrawn. Data to be presented include revised values for very short-lived nuclides, long-lived nuclides, and beta-beta decay measurements. There has been a reassessment of the spontaneous fission (sf) half-lives, which distinguishes between sf decay half-lives and cluster decay half-lives, and with cluster-fission decay. New measurements of isotopic abundance values for many elements will be discussed with an emphasis on the minor isotopes of interest for use in neutron activation analysis measurements. Neutron resonance integrals will be discussed emphasizing the differences between the calculated values obtained from the analytical integration over neutron resonances and the measured values in a neutron reactor-spectrum, which does not quite conform to the assumed 1/E neutron energy spectrum. The method used to determine the neutron resonance integral from measurement, using neutron activation analysis, will be discussed

Observation of Neutron Skyshine from an Accelerator Based Neutron Source

Energy Technology Data Exchange (ETDEWEB)

Franklyn, C. B. [Radiation Science Department, Necsa, PO Box 582, Pretoria 0001 (South Africa)

2011-12-13

A key feature of neutron based interrogation systems is the need for adequate provision of shielding around the facility. Accelerator facilities adapted for fast neutron generation are not necessarily suitably equipped to ensure complete containment of the vast quantity of neutrons generated, typically >10{sup 11} n{center_dot}s{sup -1}. Simulating the neutron leakage from a facility is not a simple exercise since the energy and directional distribution can only be approximated. Although adequate horizontal, planar shielding provision is made for a neutron generator facility, it is sometimes the case that vertical shielding is minimized, due to structural and economic constraints. It is further justified by assuming the atmosphere above a facility functions as an adequate radiation shield. It has become apparent that multiple neutron scattering within the atmosphere can result in a measurable dose of neutrons reaching ground level some distance from a facility, an effect commonly known as skyshine. This paper describes a neutron detection system developed to monitor neutrons detected several hundred metres from a neutron source due to the effect of skyshine.

Validation of a high performance liquid chromatography method for quantitation of L-proline in 20 % tincture from Murraya paniculata L. Jack

International Nuclear Information System (INIS)

Varona Torres, Noel; Gutierrez Gaiten, Yamilet Irene; Casado Martin, Celia Magaly

2014-01-01

The search for analytical methods that may monitor the quality of drugs is an issue of great interest in the pharmaceutical field, even more if they are directed to studying chemical markers of medicinal plants, their extracts and phytomedicines. To validate a high-resolution liquid chromatography (HPLC) method for the quantitative determination of the L-proline amino acid as a marker substance in Murraya paniculata L. Jack tincture

Pulsed neutron uranium borehole logging with prompt fission neutrons

International Nuclear Information System (INIS)

Bivens, H.M.; Smith, G.W.; Jensen, D.H.

1976-01-01

The gross count natural gamma log normally used for uranium borehole logging is seriously affected by disequilibrium. Methods for the direct measurement of uranium, such as neutron logging, which are not affected by disequilibrium have been the object of considerable effort in recent years. This paper describes a logging system for uranium which uses a small accelerator to generate pulses of 14 MeV neutrons to detect and assay uranium by the measurement of prompt fission neutrons in the epithermal energy range. After an initial feasibility study, a prototype logging probe was built for field evaluation which began in January 1976. Physical and operational characteristics of the prototype probe, the neutron tube-transformer assembly, and the neutron tube are described. In logging operations, only the epithermal prompt fission neutrons detected between 250 microseconds to 2500 microseconds following the excitation neutron pulse are counted. Comparison of corrected neutron logs with the conventional gross count natural gamma logs and the chemical assays of cores from boreholes are shown. The results obtained with this neutron probe clearly demonstrate its advantages over the gross count natural gamma log, although at this time the accuracy of the neutron log assay is not satisfactory under some conditions. The necessary correction factors for various borehole and formation parameters are being determined and, when applied, should improve the assay accuracy

Neutron reflectometry

International Nuclear Information System (INIS)

Van Well, A.A.

1999-01-01

Neutron research where reflection, refraction, and interference play an essential role is generally referred to as 'neutron optics'. The neutron wavelength, the scattering length density and the magnetic properties of the material determine the critical angle for total reflection. The theoretical background of neutron reflection, experimental methods and the interpretation of reflection data are presented. (K.A.)

Solar drying of jack fruit almonds Secagem solar de amêndoas de jaca

Directory of Open Access Journals (Sweden)

Alexandre J. de M Queiroz

2011-12-01

Full Text Available Dryers heated by solar energy have been constructed and used in drying whole and half jack fruit almonds. The samples were dried during the day in direct sun and in the conventional solar dryer prepared for this purpose. Another piece of equipment was built for reception and accumulation of sun energy in a body of water, which was used as a heat source for night drying. The drying with the sun energy was compared with artificial drying. The jack fruit almonds were dried whole, half, with pellicle and without it. The storage of solar energy in water was technically viable for use in night drying. The drying by combining solar dryers in the day and night periods were completed in approximately 35 hours, and were equivalent to artificial drying between 40ºC and 70ºC. Almond cut in half and the pellicle removed reduced the drying time.Secadores com aquecimento por energia solar foram construídos e utilizados em secagens de amêndoas de jaca inteiras e em metades. As secagens no período diurno foram realizadas por exposição direta ao sol e em secador solar convencional, elaborado para este fim. Construiu-se também um equipamento para captação e acumulação de energia solar em uma massa de água, a qual foi utilizada como fonte de calor para realização de secagens no período noturno. As secagens com o uso de energia solar foram comparadas com secagens artificiais. As amêndoas de jaca foram secadas inteiras, em metades, com e sem película. O armazenamento da energia solar em corpo de água mostrou-se viável do ponto de vista técnico para utilização em secagens noturnas. As secagens combinando secadores por energia solar nos períodos diurno e noturno foram concluídas em tempos aproximados de 35 horas e equivaleram a secagens artificiais entre 40 ºC e 70 ºC. O corte das amêndoas e a retirada das películas reduziram o tempo de secagem.

Pulsed neutron generator for use with pulsed neutron activation techniques

International Nuclear Information System (INIS)

Rochau, G.E.

1980-01-01

A high-output, transportable, pulsed neutron generator has been developed by Sandia National Laboratories for use with Pulsed Neutron Activation (PNA) techniques. The PNA neutron generator generates > 10 10 14 MeV D-T neutrons in a 1.2 millisecond pulse. Each operation of the unit will produce a nominal total neutron output of 1.2 x 10 10 neutrons. The generator has been designed to be easily repaired and modified. The unit requires no additional equipment for operation or measurement of output

Neutron nuclear physics under the neutron science project

Energy Technology Data Exchange (ETDEWEB)

Chiba, Satoshi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1997-11-01

The concept of fast neutron physics facility in the Neutron Science Research project is described. This facility makes use of an ultra-short proton pulse (width < 1 ns) for fast neutron time-of-flight works. The current design is based on an assumption of the maximum proton current of 100 {mu}A. Available neutron fluence and energy resolution are explained. Some of the research subjects to be performed at this facility are discussed. (author)

Development of highly effective neutron shields and neutron absorbing materials

International Nuclear Information System (INIS)

Tsuda, K.; Matsuda, F.; Taniuchi, H.; Yuhara, T.; Iida, T.

1993-01-01

A wide range of materials, including polymers and hydrogen-occluded alloys that might be usable as the neutron shielding material were examined. And a wide range of materials, including aluminum alloys that might be usable as the neutron-absorbing material were examined. After screening, the candidate material was determined on the basis of evaluation regarding its adaptabilities as a high-performance neutron-shielding and neutron-absorbing material. This candidate material was manufactured for trial, after which material properties tests, neutron-shielding tests and neutron-absorbing tests were carried out on it. The specifications of this material were thus determined. This research has resulted in materials of good performance; a neutron-shielding material based on ethylene propylene rubber and titanium hydride, and a neutron-absorbing material based on aluminum and titanium hydride. (author)

Methods for absorbing neutrons

Science.gov (United States)

Guillen, Donna P [Idaho Falls, ID; Longhurst, Glen R [Idaho Falls, ID; Porter, Douglas L [Idaho Falls, ID; Parry, James R [Idaho Falls, ID

2012-07-24

A conduction cooled neutron absorber may include a metal matrix composite that comprises a metal having a thermal neutron cross-section of at least about 50 barns and a metal having a thermal conductivity of at least about 1 W/cmK. Apparatus for providing a neutron flux having a high fast-to-thermal neutron ratio may include a source of neutrons that produces fast neutrons and thermal neutrons. A neutron absorber positioned adjacent the neutron source absorbs at least some of the thermal neutrons so that a region adjacent the neutron absorber has a fast-to-thermal neutron ratio of at least about 15. A coolant in thermal contact with the neutron absorber removes heat from the neutron absorber.

Neutron scattering. Lectures

International Nuclear Information System (INIS)

Brueckel, Thomas; Heger, Gernot; Richter, Dieter; Roth, Georg; Zorn, Reiner

2013-01-01

The following topics are dealt with: Neutron sources, symmetry of crystals, nanostructures investigated by small-angle neutron scattering, structure of macromolecules, spin dependent and magnetic scattering, structural analysis, neutron reflectometry, magnetic nanostructures, inelastic neutron scattering, strongly correlated electrons, polymer dynamics, applications of neutron scattering. (HSI)

Development of Cold Neutron Activation Station at HANARO Cold Neutron Source

International Nuclear Information System (INIS)

Sun, G. M.; Hoang, S. M. T.; Moon, J. H.; Chung, Y. S.; Cho, S. J.; Lee, K. H.; Park, B. G.; Choi, H. D.

2012-01-01

A new cold neutron source at the HANARO Research Reactor had been constructed in the framework of a five-year project, and ended in 2009. It has seven neutron guides, among which five guides were already allocated for a number of neutron scattering instruments. A new two-year project to develop a Cold Neutron Activation Station (CONAS) was carried out at the two neutron guides since May 2010, which was supported by the program of the Ministry of Education, Science and Technology, Korea. Fig. 1 shows the location of CONAS. CONAS is a complex facility including several radioanalytical instruments utilizing neutron capture reaction to analyze elements in a sample. It was designed to include three instruments like a CN-PGAA (Cold Neutron - Prompt Gamma Activation Analysis), a CN-NIPS (Cold Neutron - Neutron Induced Pair Spectrometer), and a CN-NDP (Cold Neutron - Neutron-induced prompt charged particle Depth Profiling). Fig. 2 shows the conceptual configuration of the CONAS concrete bioshield and the instruments. CN-PGAA and CN-NIPS measure the gamma-rays promptly emitted from the sample after neutron capture, whereas CN-NDP is a probe to measure the charged particles emitted from the sample surface after neutron capture. For this, we constructed two cold neutron guides called CG1 and CG2B guides from the CNS

Effect of Pasak Bumi (Eurycoma longifolia Jack) Root In Precopulation Stage to the Fertility of Female Mouse (Mus musculus L.)

OpenAIRE

Marlinza, Rosa

2012-01-01

Pasak Bumi (Eurycoma longifolia Jack) have potency to be used to increase bodyendurance, to cure malaria drug, and to act as afrodisiak. However, the effect of pasak bumi onwomen fertility, especially at pre-copulation stage was not widely known. This research seeks toreveal the effect pasak bumi extract treated at pre-copulation phase on fertility. This experimentemploy mice (Mus Musculus L.) and was undertaken at Biology and Cemistry laboratories PMIPA, andVeterinary laboratory of Jambi Uni...

Proposal for the award of a contract for the supply of motor unit for the jacks for the LHC low-beta quadrupoles

CERN Document Server

2005-01-01

This document concerns the award of a contract for the supply of 134 motor units for the jacks for the LHC low-beta quadrupoles. The Finance Committee is invited to agree to the negotiation of a contract with ZTS VVU KOSICE (SK), the lowest bidder, for the supply of 134 motor units for a total amount of 1 266 674 Swiss francs, not subject to revision.

The magnetic diffusion of neutrons; La diffusion magnetique des neutrons

Energy Technology Data Exchange (ETDEWEB)

Koehler, W C [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

1959-07-01

The purpose of this report is to examine briefly the diffusion of neutrons by substances, particularly by crystals containing permanent atomic or ionic magnetic moments. In other words we shall deal with ferromagnetic, antiferromagnetic, ferrimagnetic or paramagnetic crystals, but first it is necessary to touch on nuclear diffusion of neutrons. We shall start with the interaction of the neutron with a single diffusion centre; the results will then be applied to the magnetic interactions of the neutron with the satellite electrons of the atom; finally we shall discuss the diffusion of neutrons by crystals. (author) [French] Le but de ce rapport est d'examiner, brievement, la diffusion des neutrons par les substances, et surtout, par des cristaux qui contiennent des moments magnetiques atomiques ou ioniques permanents. C'est-a-dire que nous nous interesserons aux cristaux ferromagnetiques, antiferromagnetiques, ferrimagnetiques ou paramagnetiques; il nous faut cependant rappeler d'abord la diffusion nucleaire des neutrons. Nous commencerons par l'interaction du neutron avec un seul centre diffuseur; puis les resultats seront appliques aux interactions magnetiques du neutron avec les electrons satellites de l'atome; enfin nous discuterons la diffusion des neutrons par les cristaux. (auteur)

Neutron scattering. Lectures

Energy Technology Data Exchange (ETDEWEB)

Brueckel, Thomas; Heger, Gernot; Richter, Dieter; Roth, Georg; Zorn, Reiner (eds.)

2010-07-01

The following topics are dealt with: Neutron sources, neutron properties and elastic scattering, correlation functions measured by scattering experiments, symmetry of crystals, applications of neutron scattering, polarized-neutron scattering and polarization analysis, structural analysis, magnetic and lattice excitation studied by inelastic neutron scattering, macromolecules and self-assembly, dynamics of macromolecules, correlated electrons in complex transition-metal oxides, surfaces, interfaces, and thin films investigated by neutron reflectometry, nanomagnetism. (HSI)

Neutron scattering. Lectures

International Nuclear Information System (INIS)

Brueckel, Thomas; Heger, Gernot; Richter, Dieter; Roth, Georg; Zorn, Reiner

2010-01-01

The following topics are dealt with: Neutron sources, neutron properties and elastic scattering, correlation functions measured by scattering experiments, symmetry of crystals, applications of neutron scattering, polarized-neutron scattering and polarization analysis, structural analysis, magnetic and lattice excitation studied by inelastic neutron scattering, macromolecules and self-assembly, dynamics of macromolecules, correlated electrons in complex transition-metal oxides, surfaces, interfaces, and thin films investigated by neutron reflectometry, nanomagnetism. (HSI)

Multi-gene phylogeny of jacks and pompanos (Carangidae), including placement of monotypic vadigo Campogramma glaycos.

Science.gov (United States)

Damerau, M; Freese, M; Hanel, R

2018-01-01

In this study, the phylogenetic trees of jacks and pompanos (Carangidae), an ecologically and morphologically diverse, globally distributed fish family, are inferred from a complete, concatenated data set of two mitochondrial (cytochrome c oxidase I, cytochrome b) loci and one nuclear (myosin heavy chain 6) locus. Maximum likelihood and Bayesian inferences are largely congruent and show a clear separation of Carangidae into the four subfamilies: Scomberoidinae, Trachinotinae, Naucratinae and Caranginae. The inclusion of the carangid sister lineages Coryphaenidae (dolphinfishes) and Rachycentridae (cobia), however, render Carangidae paraphyletic. The phylogenetic trees also show with high statistical support that the monotypic vadigo Campogramma glaycos is the sister to all other species within the Naucratinae. © 2017 The Fisheries Society of the British Isles.

Neutron polarization

International Nuclear Information System (INIS)

Firk, F.W.K.

1976-01-01

Some recent experiments involving polarized neutrons are discussed; they demonstrate how polarization studies provide information on fundamental aspects of nuclear structure that cannot be obtained from more traditional neutron studies. Until recently, neutron polarization studies tended to be limited either to very low energies or to restricted regions at higher energies, determined by the kinematics of favorable (p, vector n) and (d, vector n) reactions. With the advent of high intensity pulsed electron and proton accelerators and of beams of vector polarized deuterons, this is no longer the case. One has entered an era in which neutron polarization experiments are now being carried out, in a routine way, throughout the entire range from thermal energies to tens-of-MeV. The significance of neutron polarization studies is illustrated in discussions of a wide variety of experiments that include the measurement of T-invariance in the β-decay of polarized neutrons, a search for the effects of meson exchange currents in the photo-disintegration of the deuteron, the determination of quantum numbers of states in the fission of aligned 235 U and 237 Np induced by polarized neutrons, and the double- and triple-scattering of fast neutrons by light nuclei

Neutron imaging integrated circuit and method for detecting neutrons

Science.gov (United States)

Nagarkar, Vivek V.; More, Mitali J.

2017-12-05

The present disclosure provides a neutron imaging detector and a method for detecting neutrons. In one example, a method includes providing a neutron imaging detector including plurality of memory cells and a conversion layer on the memory cells, setting one or more of the memory cells to a first charge state, positioning the neutron imaging detector in a neutron environment for a predetermined time period, and reading a state change at one of the memory cells, and measuring a charge state change at one of the plurality of memory cells from the first charge state to a second charge state less than the first charge state, where the charge state change indicates detection of neutrons at said one of the memory cells.

Neutron reflector design with Californium 252 neutron for Boron neutron chapter therapy facility using MCNP5 simulation method

International Nuclear Information System (INIS)

Muhammad Fakhrurreza; Kusminanto; Y Sardjono

2014-01-01

In this research has made a reflector design to provide beams of Neutron for BNCT with Californium-252 radioactive source. This collimator is useful to obtain optimum epithermal neutron flux with the smallest impurity radiation (thermal neutron, fast neutron, and gamma). The design process is done using Monte Carlo N-Particle simulation version 5 (MCNP5) code to calculate the neutron flux tally form. The chosen reflector design is the reflectors which use material such as BeO ceramic with 13 cm thick. Moderator use sulfur material with the slope angle of the cone is 30°. From the calculation result, it is obtained that Reflector with 1 gram Californium-252 source can produce a neutron output thermal which has thermal neutron specification 2.23189 x 10 9 n/s.cm 2 , epithermal neutron 3.51548 x 10 9 n/s.cm 2 , and fast neutron 4.82241 x 10 9 n/s.cm 2 From the result, it needs additional collimator because the BNCT requirement. (author)

Neutron spectometers

International Nuclear Information System (INIS)

Poortmans, F.

1977-01-01

Experimental work in the field of low-energy neutron physics can be subdivided into two classes: 1)Study of the decay process of the compound-nucleus state as for example the study of the capture gamma rays and of the neutron induced fission process; 2)Study of the reaction mechanism, mainly by measuring the reaction cross-sections and resonance parameters. These neutron cross-sections and resonance parameters are also important data required for many technological applications especially for reactor development programmes. In general, the second class of experiments impose other requirements on the neutron spectrometer than the first class. In most cases, a better neutron energy resolution and a broader neutron energy range are required for the study of the reaction mechanism than for the study of various aspects of the decay process. (author)

Neutron scattering. Lectures

International Nuclear Information System (INIS)

Brueckel, Thomas; Heger, Gernot; Richter, Dieter; Roth, Georg; Zorn, Reiner

2012-01-01

The following topics are dealt with: Neutron scattering in contemporary research, neutron sources, symmetry of crystals, diffraction, nanostructures investigated by small-angle neutron scattering, the structure of macromolecules, spin dependent and magnetic scattering, structural analysis, neutron reflectometry, magnetic nanostructures, inelastic scattering, strongly correlated electrons, dynamics of macromolecules, applications of neutron scattering. (HSI)

Aerial Neutron Detection: Neutron Signatures for Nonproliferation and Emergency Response Applications

Energy Technology Data Exchange (ETDEWEB)

Maurer, Richard J.; Stampahar, Thomas G.; Smith, Ethan X.; Mukhopadhyay, Sanjoy; Wolff, Ronald S.; Rourke, Timothy J.; LeDonne, Jeffrey P.; Avaro, Emanuele; Butler, D. Andre; Borders, Kevin L.; Stampahar, Jezabel; Schuck, William H.; Selfridge, Thomas L.; McKissack, Thomas M.; Duncan, William W.; Hendricks, Thane J.

2012-10-17

From 2007 to the present, the Remote Sensing Laboratory has been conducting a series of studies designed to expand our fundamental understanding of aerial neutron detection with the goal of designing an enhanced sensitivity detection system for long range neutron detection. Over 35 hours of aerial measurements in a helicopter were conducted for a variety of neutron emitters such as neutron point sources, a commercial nuclear power reactor, nuclear reactor spent fuel in dry cask storage, depleted uranium hexafluoride and depleted uranium metal. The goals of the project were to increase the detection sensitivity of our instruments such that a 5.4 × 104 neutron/second source could be detected at 100 feet above ground level at a speed of 70 knots and to enhance the long-range detection sensitivity for larger neutron sources, i.e., detection ranges above 1000 feet. In order to increase the sensitivity of aerial neutron detection instruments, it is important to understand the dynamics of the neutron background as a function of altitude. For aerial neutron detection, studies have shown that the neutron background primarily originates from above the aircraft, being produced in the upper atmosphere by galactic cosmic-ray interactions with air molecules. These interactions produce energetic neutrons and charged particles that cascade to the earth’s surface, producing additional neutrons in secondary collisions. Hence, the neutron background increases as a function of altitude which is an impediment to long-range neutron detection. In order to increase the sensitivity for long range detection, it is necessary to maintain a low neutron background as a function of altitude. Initial investigations show the variation in the neutron background can be decreased with the application of a cosmic-ray shield. The results of the studies along with a representative data set are presented.

Clinical Performance and Safety of 108 SpineJack Implantations: 1-Year Results of a Prospective Multicentre Single-Arm Registry Study

Directory of Open Access Journals (Sweden)

David Noriega

2015-01-01

Full Text Available This prospective, consecutive, multicentre observational registry aimed to confirm the safety and clinical performance of the SpineJack system for the treatment of vertebral compression fractures (VCF of traumatic origin. We enrolled 103 patients (median age: 61.6 years with 108 VCF due to trauma, or traumatic VCF with associated osteoporosis. Primary outcome was back pain intensity (VAS. Secondary outcomes were Oswestry Disability Index (ODI, EuroQol-VAS, and analgesic consumption. 48 hours after surgery, a median relative decrease in pain intensity of 81.5% was observed associated with a significant reduction in analgesic intake. Improvements in disability (91.3% decrease in ODI score and in quality of life (increase 21.1% of EQ-VAS score were obtained 3 months after surgery. All results were maintained at 12 months. A reduction in the kyphotic angulation was observed postoperatively (-5.4±6.3°; p<0.001, remained at 12 months (-4.4±6.0°, p=0.002. No adverse events were implant-related and none required device removal. Three patients (2.9% experienced procedure-related complications. The overall adjacent fracture rate up to 1 year after surgery was 2.9%. The SpineJack procedure is an effective, low-risk procedure for patients with traumatic VCF allowing a fast and sustained improvement in quality of life over 1 year after surgery.

Synovectomy by Neutron capture; Sinovectomia por captura de neutrones

Energy Technology Data Exchange (ETDEWEB)

Vega C, H.R.; Torres M, C. [Centro Regional de Estudios Nucleares, Universidad Autonoma de Zacatecas, C. Cipres 10, Fracc. La Penuela, 98000 Zacatecas (Mexico)

1998-12-31

The Synovectomy by Neutron capture has as purpose the treatment of the rheumatoid arthritis, illness which at present does not have a definitive curing. This therapy requires a neutron source for irradiating the articulation affected. The energy spectra and the intensity of these neutrons are fundamental since these neutrons induce nuclear reactions of capture with Boron-10 inside the articulation and the freely energy of these reactions is transferred at the productive tissue of synovial liquid, annihilating it. In this work it is presented the neutron spectra results obtained with moderator packings of spherical geometry which contains in its center a Pu{sup 239} Be source. The calculations were realized through Monte Carlo method. The moderators assayed were light water, heavy water base and the both combination of them. The spectra obtained, the average energy, the neutron total number by neutron emitted by source, the thermal neutron percentage and the dose equivalent allow us to suggest that the moderator packing more adequate is what has a light water thickness 0.5 cm (radius 2 cm) and 24.5 cm heavy water (radius 26.5 cm). (Author)

Assessing neutron generator output using neutron activation of silicon

International Nuclear Information System (INIS)

Kehayias, Pauli M.; Kehayias, Joseph J.

2007-01-01

D-T neutron generators are used for elemental composition analysis and medical applications. Often composition is determined by examining elemental ratios in which the knowledge of the neutron flux is unnecessary. However, the absolute value of the neutron flux is required when the generator is used for neutron activation analysis, to study radiation damage to materials, to monitor the operation of the generator, and to measure radiation exposure. We describe a method for absolute neutron output and flux measurements of low output D-T neutron generators using delayed activation of silicon. We irradiated a series of silicon oxide samples with 14.1 MeV neutrons and counted the resulting gamma rays of the 28 Al nucleus with an efficiency-calibrated detector. To minimize the photon self-absorption effects within the samples, we used a zero-thickness extrapolation technique by repeating the measurement with samples of different thicknesses. The neutron flux measured 26 cm away from the tritium target of a Thermo Electron A-325 D-T generator (Thermo Electron Corporation, Colorado Springs, CO) was 6.2 x 10 3 n/s/cm 2 ± 5%, which is consistent with the manufacturer's specifications

Assessing neutron generator output using neutron activation of silicon

Energy Technology Data Exchange (ETDEWEB)

Kehayias, Pauli M. [Body Composition Laboratory, Jean Mayer United States Department of Agriculture Human Nutrition Research Center on Aging, Tufts University, Boston, MA 02111 (United States); Kehayias, Joseph J. [Body Composition Laboratory, Jean Mayer United States Department of Agriculture Human Nutrition Research Center on Aging, Tufts University, Boston, MA 02111 (United States)]. E-mail: joseph.kehayias@tufts.edu

2007-08-15

D-T neutron generators are used for elemental composition analysis and medical applications. Often composition is determined by examining elemental ratios in which the knowledge of the neutron flux is unnecessary. However, the absolute value of the neutron flux is required when the generator is used for neutron activation analysis, to study radiation damage to materials, to monitor the operation of the generator, and to measure radiation exposure. We describe a method for absolute neutron output and flux measurements of low output D-T neutron generators using delayed activation of silicon. We irradiated a series of silicon oxide samples with 14.1 MeV neutrons and counted the resulting gamma rays of the {sup 28}Al nucleus with an efficiency-calibrated detector. To minimize the photon self-absorption effects within the samples, we used a zero-thickness extrapolation technique by repeating the measurement with samples of different thicknesses. The neutron flux measured 26 cm away from the tritium target of a Thermo Electron A-325 D-T generator (Thermo Electron Corporation, Colorado Springs, CO) was 6.2 x 10{sup 3} n/s/cm{sup 2} {+-} 5%, which is consistent with the manufacturer's specifications.

Hyper-thermal neutron irradiation field for neutron capture therapy

International Nuclear Information System (INIS)

Sakurai, Yoshinori; Kobayashi, Tooru; Kanda, Keiji

1994-01-01

The utilization of hyper-thermal neutrons, which have an energy spectrum of a Maxwell distribution higher than the room temperature of 300 K, has been studied in order to improve the thermal neutron flux distribution in a living body for a deep-seated tumor in neutron capture therapy (NCT). Simulation calculations using MCNP-V3 were carried out in order to investigate the characteristics of the hyper-thermal neutron irradiation field. From the results of simulation calculations, the following were confirmed: (i) The irradiation field of the hyper-thermal neutrons is feasible by using some scattering materials with high temperature, such as Be, BeO, C, SiC and ZrH 1.7 . Especially, ZrH 1.7 is thought to be the best material because of good characteristics of up-scattering for thermal neutrons. (ii) The ZrH 1.7 of 1200 K yields the hyper-thermal neutrons of a Maxwell-like distribution at about 2000 K and the treatable depth is about 1.5 cm larger comparing with the irradiation of the thermal neutrons of 300 K. (iii) The contamination by the secondary gamma-rays from the scattering materials can be sufficiently eliminated to the tolerance level for NCT through the bismuth layer, without the larger change of the energy spectrum of hyper-thermal neutrons. ((orig.))

Effects of neutron spectrum and external neutron source on neutron multiplication parameters in accelerator-driven system

International Nuclear Information System (INIS)

Shahbunder, Hesham; Pyeon, Cheol Ho; Misawa, Tsuyoshi; Lim, Jae-Yong; Shiroya, Seiji

2010-01-01

The neutron multiplication parameters: neutron multiplication M, subcritical multiplication factor k s , external source efficiency φ*, play an important role for numerical assessment and reactor power evaluation of an accelerator-driven system (ADS). Those parameters can be evaluated by using the measured reaction rate distribution in the subcritical system. In this study, the experimental verification of this methodology is performed in various ADS cores; with high-energy (100 MeV) proton-tungsten source in hard and soft neutron spectra cores and 14 MeV D-T neutron source in soft spectrum core. The comparison between measured and calculated multiplication parameters reveals a maximum relative difference in the range of 6.6-13.7% that is attributed to the calculation nuclear libraries uncertainty and accuracy for energies higher than 20 MeV and also dependent on the reaction rate distribution position and count rates. The effects of different core neutron spectra and external neutron sources on the neutron multiplication parameters are discussed.

Neutron dosimetry at SLAC: Neutron sources and instrumentation

International Nuclear Information System (INIS)

Liu, J.C.; Jenkins, T.M.; McCall, R.C.; Ipe, N.E.

1991-10-01

This report summarizes in detail the dosimetric characteristics of the five radioisotopic type neutron sources ( 238 PuBe, 252 Cf, 238 PuB, 238 PuF 4 , and 238 PuLi) and the neutron instrumentation (moderated BF 3 detector, Anderson-Braun (AB) detector, AB remmeter, Victoreen 488 Neutron Survey Meter, Beam Shut-Off Ionization Chamber, 12 C plastic scintillator detector, moderated indium foil detector, and moderated and bare TLDs) that are commonly used for neutron dosimetry at the Stanford Linear Accelerator Center (SLAC). 36 refs,. 19 figs

Production of 14 MeV neutrons from D-D neutron generators

International Nuclear Information System (INIS)

Cecil, F.E.; Nieschmidt, E.B.

1986-01-01

The production of 14 MeV neutrons from a D-D neutron generator resulting from tritium buildup from the d(d,p)t reaction in the target is discussed. The effect of the 14 MeV neutrons on fast neutron activation analysis with D-D neutron generators is evaluated. (orig.)

Biochemical components of seminal plasma and their correlation to the fresh seminal characteristics in Marwari stallions and Poitou jacks

Directory of Open Access Journals (Sweden)

Thirumala Rao Talluri

2017-02-01

Full Text Available Aim: To investigate various biochemical components of seminal plasma in Marwari stallions and Poitou Jacks and to find out their correlation with that of the seminal characteristics. Materials and Methods: In this study, semen was collected from six Marwari stallions and six Poitou jacks aged from 4 to 6 years and with known fertility status. The semen collection from the stallions were collected during the breeding season, i.e., between the months of April and June. From the collected semen ejaculates, we estimated the values of some biochemical components, viz., total protein content, total lipid content, and enzymes such as glutamic pyruvic transaminase (GPT, glutamic oxaloacetic transaminase (GOT, alkaline phosphatase (ALP, acid phosphatase (ACP, and lactate dehydrogenase (LDH as well as concentrations of glucose, cholesterol, total calcium (Ca, and phosphorus (P and correlations among different seminal parameters were statistically examined using the Pearson correlation coefficient. Results: In this study, we found positive correlations between semen volume as well as sperm concentration and GOT, GPT, ALP and ACP for both the group stallions. Significant correlation between motility and glucose, GOT and GPT could be an indication for their role metabolism and protection against free radicals to the spermatozoa. Conclusion: Based on the results, it is concluded that there is a positive correlation between some biochemical values such as glucose, Ca, ALP, and LDH and seminal parameters which play a key role in capacitation and onward movement of the spermatozoa.

Pulsed neutron generator

International Nuclear Information System (INIS)

Bespalov, D.F.; Bykovskii, Yu.A.; Vergun, I.I.; Kozlovskii, K.I.; Kozyrev, Yu.P.; Leonov, R.K.; Simagin, B.I.; Tsybin, A.S.; Shikanov, A.Ie.

1986-03-01

The paper describes a new device for generating pulsed neutron fields, utilized in nuclear geophysics for carrying out pulsed neutron logging and activation analysis under field conditions. The invention employs a sealed-off neutron tube with a laser ion source which increases neutron yield to the level of 10 neutrons per second or higher. 2 refs., 1 fig

Neutron PSDs for the next generation of spallation neutron sources

CERN Document Server

Eijk, C W

2002-01-01

A review of R and D for neutron PSDs to be used at anticipated new spallation neutron sources: the Time-of-Flight system facility, European Spallation Source, Spallation Neutron Source and Neutron Arena, is presented. The gas-filled detectors, scintillation detectors and hybrid systems are emphasized.

New neutron imaging using pulsed sources. Characteristics of a pulsed neutron source and principle of pulsed neutron imaging

International Nuclear Information System (INIS)

Kiyanagi, Yoshiaki

2012-01-01

Neutron beam is one of important tools to obtain the transmission image of an object. Until now, steady state neutron sources such as reactors are mainly used for this imaging purpose. Recently, it has been demonstrated that pulsed neutron imaging based on accelerator neutron sources can provide a real-space distribution of physical information of materials such as crystallographic structure, element, temperature, hydrogen bound state, magnetic field and so on, by analyzing wavelength dependent transmission spectrum, which information cannot be observed or difficult to obtain with a traditional imaging method using steady state neutrons. Here, characteristics of the pulsed neutron source and principle of the pulsed neutron imaging are explained as a basic concept of the new method. (author)

Neutron guides and scientific neutron equipment at CILAS/GMI

International Nuclear Information System (INIS)

Gautier-Picard, P.

2003-01-01

CILAS company is the world's leading supplier of complete neutron guides systems. The neutron optics with multilayer coatings produced by CILAS have become an international standard for neutron beam transportation in the modern research institutes. During the last 30 years, CILAS designed, produced and installed more than 5000 meters of guides in many European, American and Asian countries. To reinforce its leadership and presence in neutron research, CILAS acquired the company Grenoble Modular Instruments (GMI), a leading company in high precision mechanics, engineering and manufacturing of spectrometers and scientific equipment for neutron and synchrotron research. (author)

Neutron detector

Science.gov (United States)

Stephan, Andrew C [Knoxville, TN; Jardret,; Vincent, D [Powell, TN

2011-04-05

A neutron detector has a volume of neutron moderating material and a plurality of individual neutron sensing elements dispersed at selected locations throughout the moderator, and particularly arranged so that some of the detecting elements are closer to the surface of the moderator assembly and others are more deeply embedded. The arrangement captures some thermalized neutrons that might otherwise be scattered away from a single, centrally located detector element. Different geometrical arrangements may be used while preserving its fundamental characteristics. Different types of neutron sensing elements may be used, which may operate on any of a number of physical principles to perform the function of sensing a neutron, either by a capture or a scattering reaction, and converting that reaction to a detectable signal. High detection efficiency, an ability to acquire spectral information, and directional sensitivity may be obtained.

Development of fast neutron radiography system based on portable neutron generator

Energy Technology Data Exchange (ETDEWEB)

Yi, Chia Jia, E-mail: gei-i-kani@hotmail.com; Nilsuwankosit, Sunchai, E-mail: sunchai.n@chula.ac.th [Department of Nuclear Engineering, Faculty of Engineering, Chulalongkorn University, Phayathai Rd., Patumwan, Bangkok, THAILAND 10330 (Thailand)

2016-01-22

Due to the high installation cost, the safety concern and the immobility of the research reactors, the neutron radiography system based on portable neutron generator is proposed. Since the neutrons generated from a portable neutron generator are mostly the fast neutrons, the system is emphasized on using the fast neutrons for the purpose of conducting the radiography. In order to suppress the influence of X-ray produced by the neutron generator, a combination of a shielding material sandwiched between two identical imaging plates is used. A binary XOR operation is then applied for combining the information from the imaging plates. The raw images obtained confirm that the X-ray really has a large effect and that XOR operation can help enhance the effect of the neutrons.

Impact of the cosmetic mouthwash “Jack Pro Spülung plus” (“rheodol-Spülung plus” on the oral cavity flora, tested in a monocentric, controlled, randomized, blind, cross-over comparative study

Directory of Open Access Journals (Sweden)

Göhring, Jana

2014-03-01

Full Text Available [english] Aim: Jack Pro Spülung Plus (also available as “rheodol-Spülung plus” is recommended to mechanically maintain oral hygiene as part of an overall oral hygiene concept. Because Jack Pro Spülung Plus contains the active agents polihexanide and tosylchloramide sodium in concentrations below microbicidal efficacy, this study tested the hypothesis that the combination of mechanical rinsing and bacteriostatic effect surpasses the effect of mechanical rinsing alone.Method: The study was performed with 30 volunteers as a monocentric, controlled, randomized, blind, cross-over comparative study. The efficacy of the test product (active agents polihexanide 0.02–0.03% and tosylchloramide sodium 0.004–0.006% was compared to an aqueous solution of polihexanide (0.02–0.03% and to Ringer solution as negative control. The efficacy was measured as the reduction of colony forming units (cfu on buccal mucosa after aerobic and anaerobic cultivation. After determination of pre-values, the volunteers performed mouthrinsing for 30 sec with each of the 3 tested solutions. After 1, 10 and 60 minutes, cfu numbers were determined again. The reduction factor was calculated as the difference between log of the measured cfu before and after mouthrinsing with the test solution. The sampling was performed using a template with a smear area of 1 x 1 cm. Results: Using Ringer solution led to a slight mechanically-induced reduction of cfu in the oral cavity 1 min after rinsing the mouth cavity with the solution. After 10 min and 60 min, no influence on the cfu number could be detected. Using Jack pro Spülung Plus led to a bacteriostatic effect up to 60 min after mouthrinsing; 10 min and 60 min after rinsing the efficacy of Ringer solution was also significantly surpassed. The aqueous solution of polihexanide was less effective than Jack pro Spülung Plus after 10 and 60 min. Conclusion: Based on these observations, we conclude that Jack pro Spülung Plus is

Neutron dosimetry at SLAC: Neutron sources and instrumentation

Energy Technology Data Exchange (ETDEWEB)

Liu, J.C.; Jenkins, T.M.; McCall, R.C.; Ipe, N.E.

1991-10-01

This report summarizes in detail the dosimetric characteristics of the five radioisotopic type neutron sources ({sup 238}PuBe, {sup 252}Cf, {sup 238}PuB, {sup 238}PuF{sub 4}, and {sup 238}PuLi) and the neutron instrumentation (moderated BF{sub 3} detector, Anderson-Braun (AB) detector, AB remmeter, Victoreen 488 Neutron Survey Meter, Beam Shut-Off Ionization Chamber, {sup 12}C plastic scintillator detector, moderated indium foil detector, and moderated and bare TLDs) that are commonly used for neutron dosimetry at the Stanford Linear Accelerator Center (SLAC). 36 refs,. 19 figs.

Directional epithermal neutron detector

International Nuclear Information System (INIS)

Givens, W.W.; Mills, W.R. Jr.

1986-01-01

A borehole tool for epithermal neutron die-away logging of subterranean formations surrounding a borehole is described which consists of: (a) a pulsed source of fast neutrons for irradiating the formations surrounding a borehole, (b) at least one neutron counter for counting epithermal neutrons returning to the borehole from the irradiated formations, (c) a neutron moderating material, (d) an outer thermal neutron shield providing a housing for the counter and the moderating material, (e) an inner thermal neutron shield dividing the housing so as to provide a first compartment bounded by the inner thermal neutron shield and a first portion of the outer thermal neutron shield and a second compartment bounded by the inner thermal neutron shield and a second portion of the outer thermal neutron shield, the counter being positioned within the first compartment and the moderating material being positioned within the second compartment, and (f) means for positioning the borehole tool against one side of the borehole wall and azimuthally orienting the borehole tool such that the first chamber is in juxtaposition with the borehole wall, the formation epithermal neutrons penetrating into the first chamber through the first portion of the outer thermal neutron shield are detected by the neutron counter for die-away measurement, thereby maximizing the directional sensitivty of the neutron counter to formation epithermal neutrons, the borehole fluid epithermal neutrons penetrating into the second chamber through the second chamber through the second portion of the outer thermal neutron shield are largely slowed down and lowered in energy by the moderating material and absorbed by the inner thermal neutron shield before penetrating into the first chamber, thereby minimizing the directional sensitivity of the neutron counter to borehole fluid epithermal neutrons

Neutron Optics: Towards Applications for Hot Neutrons

International Nuclear Information System (INIS)

Schanzer, C; Schneider, M; Böni, P

2016-01-01

Supermirrors with large critical angles of reflection, i.e. large index m are an essential ingredient to transport, focus and polarise neutrons over a wide range of energy. Here we summarise the recent developments of supermirror with very large critical angles of reflection and high reflectivity that were conducted at SwissNeutronics as well as their implementation in devices. Approaching critical angles m = 8 times the critical angle of natural nickel makes new applications possible and extends the use of reflection optics towards the regime of hot and epithermal neutrons. Based on comparisons of simulations with experiment we demonstrate future possibilities of applications of large-m supermirrors towards devices for neutrons with short wavelength. (paper)

Neutron transportation simulator

International Nuclear Information System (INIS)

Uenohara, Yuzo.

1995-01-01

In the present invention, problems in an existent parallelized monte carlo method is solved, and behaviors of neutrons in a large scaled system are accurately simulated at a high speed. Namely, a neutron transportation simulator according to the monte carlo method simulates movement of each of neutrons by using a parallel computer. In this case, the system to be processed is divided based on a space region and an energy region to which neutrons belong. Simulation of neutrons in the divided regions is allotted to each of performing devices of the parallel computer. Tarry data and nuclear data of the neutrons in each of the regions are memorized dispersedly to memories of each of the performing devices. A transmission means for simulating the behaviors of the neutrons in the region by each of the performing devices, as well as transmitting the information of the neutrons, when the neutrons are moved to other region, to the performing device in a transported portion are disposed to each of the performing devices. With such procedures, simulation for the neutrons in the allotted region can be conducted with small capacity of memories. (I.S.)

Neutronics of the IFMIF neutron source: development and analysis

International Nuclear Information System (INIS)

Wilson, P.P.H.

1999-01-01

The accurate analysis of this system required the development of a code system and methodology capable of modelling the various physical processes. A generic code system for the neutronics analysis of neutron sources has been created by loosely integrating existing components with new developments: the data processing code NJOY, the Monte Carlo neutron transport code MCNP, and the activation code ALARA were supplemented by a damage data processing program, damChar, and integrated with a number of flexible and extensible modules for the Perl scripting language. Specific advances were required to apply this code system to IFMIF. Based on the ENDF-6 data format requirements of this system, new data evaluations have been implemented for neutron transport and activation. Extensive analysis of the Li(d, xn) reaction has led to a new MCNP source function module, M c DeLi, based on physical reaction models and capable of accurate and flexible modelling of the IFMIF neutron source term. In depth analyses of the neutron flux spectra and spatial distribution throughout the high flux test region permitted a basic validation of the tools and data. The understanding of the features of the neutron flux provided a foundation for the analyses of the other neutron responses. (orig./DGE) [de

Neutron spectra and dosimetric features of isotopic neutron sources: a review

International Nuclear Information System (INIS)

Vega C, H. R.; Martinez O, S. A.

2015-10-01

A convenient way to produce neutrons is the isotopic neutron source, where the production is through (α, n), (γ, n), and spontaneous fission reactions. Isotopic neutron sources are small, easy to handle, and have a relative low cost. On the other hand the neutron yield is small and mostly of them produces neutrons with a wide energy distribution. In this work, a review is carried out about the the main features of 24 NaBe, 24 NaD 2 O, 116 InBe, 140 LaBe, 238 PuLi, 239 PuBe, 241 AmB, 241 AmBe, 241 AmF, 241 AmLi, 242 CmBe, 210 PoBe, 226 RaBe, 252 Cf and 252 Cf/D 2 O isotopic neutron source. Also, using Monte Carlo methods, the neutron spectra in 31 energy groups, the neutron mean energy; the Ambient dose equivalent, the Personal dose equivalent and the Effective dose were calculated for these isotopic neutron sources. (Author)

A neutron detector for measurement of total neutron production cross sections

International Nuclear Information System (INIS)

Sekharan, K.K.; Laumer, H.; Kern, B.D.; Gabbard, F.

1976-01-01

A neutron detector has been constructed and calibrated for the accurate measurement of total neutron production cross sections. The detector consists of a polyethylene sphere of 60 cm diameter in which eight 10 BF 3 counters have been installed radially. The relative efficiency of this detector has been determined for average neutron energies from 30 keV to 1.5 MeV by counting neutrons from 7 Li(p, n) 7 Be. By adjusting the radial positions of the BF 3 counters in the polyethylene sphere the efficiency for neutron detection was made nearly constant for this energy range. Measurement of absolute efficiency for the same neutron energy range has been done by counting the neutrons from 51 V(p, n) 51 Cr and 57 Fe(p, n) 57 Co reactions and determining the absolute number of residual nuclei produced during the measurement of neutron yield. Details of absolute efficiency measurements and the use of the detector for determination of neutron production cross sections are given. (Auth.)

Fusion neutronics

CERN Document Server

Wu, Yican

2017-01-01

This book provides a systematic and comprehensive introduction to fusion neutronics, covering all key topics from the fundamental theories and methodologies, as well as a wide range of fusion system designs and experiments. It is the first-ever book focusing on the subject of fusion neutronics research. Compared with other nuclear devices such as fission reactors and accelerators, fusion systems are normally characterized by their complex geometry and nuclear physics, which entail new challenges for neutronics such as complicated modeling, deep penetration, low simulation efficiency, multi-physics coupling, etc. The book focuses on the neutronics characteristics of fusion systems and introduces a series of theories and methodologies that were developed to address the challenges of fusion neutronics, and which have since been widely applied all over the world. Further, it introduces readers to neutronics design’s unique principles and procedures, experimental methodologies and technologies for fusion systems...

Neutron-induced peaks in Ge detectors from evaporation neutrons

International Nuclear Information System (INIS)

Gete, E.; Measday, D.F.; Moftah, B.A.; Saliba, M.A.; Stocki, T.J.

1997-01-01

We have studied the peak shapes at 596 and 691 keV resulting from fast neutron interactions inside germanium detectors. We have used neutrons from a 252 Cf source, as well as from the 28 Si(μ - , nν), and 209 Bi(π - , xn) reactions to compare the peaks and to check for a dependence of peak shape on the incoming neutron energy. In our investigation, no difference between these three measurements has been observed. In a comparison of these peak shapes with other studies, we found similar results to ours except for those measurements using monoenergetic neutrons in which a significant variation with neutron energy has been observed. (orig.)

Development of high flux thermal neutron generator for neutron activation analysis

Energy Technology Data Exchange (ETDEWEB)

Vainionpaa, Jaakko H., E-mail: hannes@adelphitech.com [Adelphi Technology, 2003 E Bayshore Rd, Redwood City, CA 94063 (United States); Chen, Allan X.; Piestrup, Melvin A.; Gary, Charles K. [Adelphi Technology, 2003 E Bayshore Rd, Redwood City, CA 94063 (United States); Jones, Glenn [G& J Jones Enterprice, 7486 Brighton Ct, Dublin, CA 94568 (United States); Pantell, Richard H. [Department of Electrical Engineering, Stanford University, Stanford, CA (United States)

2015-05-01

The new model DD110MB neutron generator from Adelphi Technology produces thermal (<0.5 eV) neutron flux that is normally achieved in a nuclear reactor or larger accelerator based systems. Thermal neutron fluxes of 3–5 · 10{sup 7} n/cm{sup 2}/s are measured. This flux is achieved using four ion beams arranged concentrically around a target chamber containing a compact moderator with a central sample cylinder. Fast neutron yield of ∼2 · 10{sup 10} n/s is created at the titanium surface of the target chamber. The thickness and material of the moderator is selected to maximize the thermal neutron flux at the center. The 2.5 MeV neutrons are quickly thermalized to energies below 0.5 eV and concentrated at the sample cylinder. The maximum flux of thermal neutrons at the target is achieved when approximately half of the neutrons at the sample area are thermalized. In this paper we present simulation results used to characterize performance of the neutron generator. The neutron flux can be used for neutron activation analysis (NAA) prompt gamma neutron activation analysis (PGNAA) for determining the concentrations of elements in many materials. Another envisioned use of the generator is production of radioactive isotopes. DD110MB is small enough for modest-sized laboratories and universities. Compared to nuclear reactors the DD110MB produces comparable thermal flux but provides reduced administrative and safety requirements and it can be run in pulsed mode, which is beneficial in many neutron activation techniques.

Fast neutron activation analysis by means of low voltage neutron generator

Directory of Open Access Journals (Sweden)

M.E. Medhat

Full Text Available A description of D-T neutron generator (NG is presented. This machine can be used for fast neutron activation analysis applied to determine some selected elements, especially light elements, in different materials. Procedure of neutron flux determination and efficiency calculation is described. Examples of testing some Egyptian natural cosmetics are given. Keywords: Neutron generator, Fast neutron activation analysis, Elemental analysis

Research of accelerator-based neutron source for boron neutron capture therapy

International Nuclear Information System (INIS)

Li Changkai; Ma Yingjie; Tang Xiaobin; Xie Qin; Geng Changran; Chen Da

2013-01-01

Background: 7 Li (p, n) reaction of high neutron yield and low threshold energy has become one of the most important neutron generating reactions for Accelerator-based Boron Neutron Capture Therapy (BNCT). Purpose Focuses on neutron yield and spectrum characteristics of this kind of neutron generating reaction which serves as an accelerator-based neutron source and moderates the high energy neutron beams to meet BNCT requirements. Methods: The yield and energy spectrum of neutrons generated by accelerator-based 7 Li(p, n) reaction with incident proton energy from 1.9 MeV to 3.0 MeV are researched using the Monte Carlo code-MCNPX2.5.0. And the energy and angular distribution of differential neutron yield by 2.5-MeV incident proton are also given in this part. In the following part, the character of epithermal neutron beam generated by 2.5-MeV incident protons is moderated by a new-designed moderator. Results: Energy spectra of neutrons generated by accelerator-based 7 Li(p, n) reaction with incident proton energy from 1.9 MeV to 3.0 MeV are got through the simulation and calculation. The best moderator thickness is got through comparison. Conclusions: Neutron beam produced by accelerator-based 7 Li(p, n) reaction, with the bombarding beam of 10 mA and the energy of 2.5 MeV, can meet the requirement of BNCT well after being moderated. (authors)

A polarizing neutron periscope for neutron imaging

International Nuclear Information System (INIS)

Schulz, Michael; Boeni, Peter; Calzada, Elbio; Muehlbauer, Martin; Neubauer, Andreas; Schillinger, Burkhard

2009-01-01

Optical neutron polarizers like guides or benders destroy the collimation of a neutron beam due to multiple reflections or scattering. This makes them unsuitable for their use in polarized neutron radiography, because the beam collimation is essential to obtain high spatial resolution. We have developed a neutron polarizer based on the principle of an optical periscope with a zigzag double reflection on two parallel high-m supermirror polarizers. If the supermirrors are perfectly parallel and flat, the beam collimation is left unchanged by such a device. A first proof of concept version of this type of polarizer was built and tested. We expect to achieve a beam polarization of up to 99% with an improved version yet to be built.

Neutron detector

International Nuclear Information System (INIS)

Endo, Hiroshi.

1993-01-01

The device of the present invention detects neutrons in a reactor container under a high temperature and reduces the noise level in an FBR type reactor. That is, the detection section comprises a high heat resistant vessel containing a scintillator therein for detecting neutrons. Neutron signals sent from the detection section are inputted to a neutron measuring section by way of a signal transmission section. The detection section is disposed at the inside of the reactor container. Further, the signal transmission section is connected optically to the detection section. With such a constitution, since the detection section comprising the high temperature resistant vessel is disposed at the inside of the reactor container, neutron fluxes can be detected and measured at high sensitivity even under a high temperature circumstance. Since the signal transmission section is optically connected to the detection section, influence of radiation rays upon transmission of the neutron detection signals can be reduced. Accordingly, the noise level can be kept low. (I.S.)

Very slow neutrons

International Nuclear Information System (INIS)

Frank, A.

1983-01-01

The history is briefly presented of the research so far of very slow neutrons and their basic properties are explained. The methods are described of obtaining very slow neutrons and the problems of their preservation are discussed. The existence of very slow neutrons makes it possible to perform experiments which may deepen the knowledge of the fundamental properties of neutrons. Their wavelength approximates that of visible radiation. The possibilities and use are discussed of neutron optical systems (neutron microscope) which could be an effective instrument for the study of the detailed arrangement, especially of organic substances. (B.S.)

Neutron in biology

International Nuclear Information System (INIS)

Niimura, Nobuo

1997-01-01

Neutron in biology can provide an experimental method of directly locating relationship of proteins and DNA. However, there are relatively few experimental study of such objects since it takes a lot of time to collect a sufficient number of Bragg reflections and inelastic spectra due to the low flux of neutron illuminating the sample. Since a next generation neutron source of JAERI will be 5MW spallation neutron source and its effective neutron flux will be 10 2 to 10 3 times higher than the one of JRR-3M, neutron in biology will open a completely new world for structural biology. (author)

Experiment of Neutron Generation by Using Prototype D-D Neutron Generator

International Nuclear Information System (INIS)

Kim, In Jung; Kim, Suk Kwon; Park, Chang Su; Jung, Nam Suk; Jung, Hwa Dong; Park, Ji Young; Hwang, Yong Seok; Choi, H.D.

2005-01-01

Experiment of neutron generation was performed by using a prototype D-D neutron generator. The characteristics of D-D neutron generation in drive-in target was studied. The increment of neutron yield by increasing ion beam energy was investigated, too

Analysis of the neutron generation from a D-Li neutron source

International Nuclear Information System (INIS)

Gomes, I.

1994-02-01

The study of the neutron generation from the D-Li reaction is an important issue to define the optimum combination of the intervening parameters during the design phase of a D-Li neutron source irradiation facility. The major players in defining the neutron yield from the D-Li reaction are the deuteron incident energy and the beam current, provided that the lithium target is thick enough to stop all incident deuterons. The incident deuteron energy also plays a role on the angular distribution of the generated neutrons, on the energy distribution of the generated neutrons, and on the maximum possible energy of the neutrons. The D-Li reaction produces neutrons with energies ranging from eV's to several MeV's. The angular distribution of these neutrons is dependent on the energy of both, incident deuterons and generated neutrons. The deuterons lose energy interacting with the lithium target material in such a way that the energy of the deuterons inside the lithium target varies from the incident deuteron energy to essentially zero. The first part of this study focuses in analyzing the neutron generation rate from the D-Li reaction as a function of the intervening parameters, in defining the source term, in terms of the energy and angular distributions of the generated neutrons, and finally in providing some insights of the impact of varying input parameters on the generation rate and correlated distributions. In the second part an analytical description of the Monte Carlo sampling procedure of the neutron from the D-Li reaction is provided with the aim at further Monte Carlo transport of the D-Li neutrons

Neutron techniques

International Nuclear Information System (INIS)

Charlton, J.S.

1986-01-01

The way in which neutrons interact with matter such as slowing-down, diffusion, neutron absorption and moderation are described. The use of neutron techniques in industry, in moisture gages, level and interface measurements, the detection of blockages, boron analysis in ore feedstock and industrial radiography are discussed. (author)

Neutron scattering. Lectures

Energy Technology Data Exchange (ETDEWEB)

Brueckel, Thomas; Heger, Gernot; Richter, Dieter; Roth, Georg; Zorn, Reiner [eds.

2010-07-01

The following topics are dealt with: Neutron sources, symmetry of crystals, diffraction, nanostructures investigated by small-angle neutron scattering, the structure of macromolecules, spin dependent and magnetic scattering, structural analysis, neutron reflectometry, magnetic nanostructures, inelastic scattering, strongly correlated electrons, dynamics of macromolecules, applications of neutron scattering. (HSI)

Neutron scattering. Lectures

International Nuclear Information System (INIS)

Brueckel, Thomas; Heger, Gernot; Richter, Dieter; Roth, Georg; Zorn, Reiner

2010-01-01

The following topics are dealt with: Neutron sources, symmetry of crystals, diffraction, nanostructures investigated by small-angle neutron scattering, the structure of macromolecules, spin dependent and magnetic scattering, structural analysis, neutron reflectometry, magnetic nanostructures, inelastic scattering, strongly correlated electrons, dynamics of macromolecules, applications of neutron scattering. (HSI)

Neutron spectra and dosimetric features of isotopic neutron sources: a review

Energy Technology Data Exchange (ETDEWEB)

Vega C, H. R. [Universidad Autonoma de Zacatecas, Unidad Academica de Estudios Nucleares, Cipres No. 10, Fracc. La Penuela, 98060 Zacatecas, Zac. (Mexico); Martinez O, S. A., E-mail: fermineutron@yahoo.com [Universidad Pedagogica y Tecnologica de Colombia, Grupo de Fisica Nuclear Aplicada y Simulacion, Av. Central del Norte 39-115, 150003 Tunja, Boyaca (Colombia)

2015-10-15

A convenient way to produce neutrons is the isotopic neutron source, where the production is through (α, n), (γ, n), and spontaneous fission reactions. Isotopic neutron sources are small, easy to handle, and have a relative low cost. On the other hand the neutron yield is small and mostly of them produces neutrons with a wide energy distribution. In this work, a review is carried out about the the main features of {sup 24}NaBe, {sup 24}NaD{sub 2}O, {sup 116}InBe, {sup 140}LaBe, {sup 238}PuLi, {sup 239}PuBe, {sup 241}AmB, {sup 241}AmBe, {sup 241}AmF, {sup 241}AmLi, {sup 242}CmBe, {sup 210}PoBe, {sup 226}RaBe, {sup 252}Cf and {sup 252}Cf/D{sub 2}O isotopic neutron source. Also, using Monte Carlo methods, the neutron spectra in 31 energy groups, the neutron mean energy; the Ambient dose equivalent, the Personal dose equivalent and the Effective dose were calculated for these isotopic neutron sources. (Author)

A neutron detector for measurement of total neutron production cross sections

Energy Technology Data Exchange (ETDEWEB)

Sekharan, K K; Laumer, H; Kern, B D; Gabbard, F [Kentucky Univ., Lexington (USA). Dept. of Physics and Astronomy

1976-03-01

A neutron detector has been constructed and calibrated for the accurate measurement of total neutron production cross sections. The detector consists of a polyethylene sphere of 60 cm diameter in which eight /sup 10/BF/sub 3/ counters have been installed radially. The relative efficiency of this detector has been determined for average neutron energies from 30 keV to 1.5 MeV by counting neutrons from /sup 7/Li(p, n)/sup 7/Be. By adjusting the radial positions of the BF/sub 3/ counters in the polyethylene sphere the efficiency for neutron detection was made nearly constant for this energy range. Measurement of absolute efficiency for the same neutron energy range has been done by counting the neutrons from /sup 51/V(p, n)/sup 51/Cr and /sup 57/Fe(p, n)/sup 57/Co reactions and determining the absolute number of residual nuclei produced during the measurement of neutron yield. Details of absolute efficiency measurements and the use of the detector for determination of neutron production cross sections are given.

Neutron radiography

International Nuclear Information System (INIS)

Alaa eldin, M.T.

2011-01-01

The digital processing of the neutron radiography images gives the possibility for data quantification. In this case an exact relation between the measured neutron attenuation and the real macroscopic attenuation coefficient for every point of the sample is required. The assumption that the attenuation of the neutron beam through the sample is exponential is valid only in an ideal case where a monochromatic beam, non scattering sample and non background contribution are assumed. In the real case these conditions are not fulfilled and in dependence on the sample material we have more or less deviation from the exponential attenuation law. Because of the high scattering cross-sections of hydrogen (σs=80.26 barn) for thermal neutrons, the problem with the scattered neutrons at quantitative radiography investigations of hydrogenous materials (as PE, Oil, H 2 O, etc) is not trivial. For these strong scattering materials the neutron beam attenuation is no longer exponential and a dependence of the macroscopic attenuation coefficient on the material thickness and on the distance between the sample and the detector appears. When quantitative radiography (2 D) or tomography investigations (3 D) are performed, some image correction procedures for a description of the scattering effect are required. This thesis presents a method that can be used to enhance the neutron radiography image for objects with high scattering materials like hydrogen, carbon and other light materials. This method uses the Monte Carlo code, MCNP5, to simulate the neutron radiography process and get the flux distribution for each pixel of the image and determine the scattered neutrons distribution that causes the image blur and then subtract it from the initial image to improve its quality.

A search for solar neutron response in neutron monitor data

International Nuclear Information System (INIS)

Kudela, K.

1990-01-01

The search for an impulsive increase corresponding to a solar neutron response on high-mountain neutron monitors requires control of the stability of the measurement and elimination of other sources of short-time increases of different kinds which are involved in fluctuations of cosmic-ray intensity. For the solar flare of June 3, 1982 the excess of counting rate on the Lomnicky stit neutron monitor is, within a factor or 1.8, equal to that expected from solar neutrons. Superposed epoch analysis of 17 flares with gamma-ray or hard X-ray production gives a slight tendency of an occurring signal in cases of high heliocentric angles, indicating anisotropic production of neutrons on the sun. The low statistical significance of the result indicates that higher temporal resolution, better evaluation of multiplicity, better knowledge of the power spectra of short-term intensity fluctuations on neutron monitors, as well as coordinated measurements of solar gamma-rays and neutrons on satellites, are required. 21 refs

Delayed neutron yield from fast neutron induced fission of 238U

International Nuclear Information System (INIS)

Piksaikin, V.M.; Kazakov, L.E.; Isaev, S.G.; Roshchenko, V.A.; Goverdovski, A.A.; Tertytchnyi, R.G.

2002-01-01

The measurements of the total delayed neutron yield from fast neutron induced fission of 238 U were made. The experimental method based on the periodic irradiation of the fissionable sample by neutrons from a suitable nuclear reaction had been employed. The preliminary results on the energy dependence of the total delayed neutron yield from fission of 238 U are obtained. According to the comparison of experimental data with our prediction based on correlation properties of delayed neutron characteristics, it is concluded that the value of the total delayed neutron yield near the threshold of (n,f) reaction is not a constant. (author)

Neutron flux stabilization in the NG-150 neutron generators

International Nuclear Information System (INIS)

Kuz'min, L.E.; Makarov, S.A.; Pronman, I.M.

1986-01-01

Problem of metal tritium target lifetime increase and neutron flux stabilization in the NG-150 neutron generators is studied. Possibility on neutron flux stabilization using the mass analyzer for low-angle (4 deg and 41 deg) mass separation of a beam in thre components, which fall on a target simultaneously, is confirmed experimentally. Basic generator parameters are: accelerating voltage of 150 kV, total beam current on a target of 1.5 mA, beam current density of 0.3-1.6 mA/cm 2 , beam diameter of 8 mm. The initial neutron flux on the targets of 0.73 mg/cm 2 thick constituted 1.1x10 11 ssup(-1). The neutron flux monitoring was accomplished from recoil proton recording by a plastic scintillator. Flux decrease by more than 5% served as a signel for measuring mass analyzer magnetic field providing beam displacement on a target and restoration of the given flux. The NG-150 generator neutron flux stabilization was attained during 2h

Neutron detection technique

International Nuclear Information System (INIS)

Oblath, N.S.; Poon, A.W.P.

2000-01-01

The Sudbury Neutrino Observatory (SNO) has the ability to measure the total flux of all active flavors of neutrinos using the neutral current reaction, whose signature is a neutron. By comparing the rates of the neutral current reaction to the charged current reaction, which only detects electron neutrinos, one can test the neutrino oscillation hypothesis independent of solar models. It is necessary to understand the neutron detection efficiency of the detector to make use of the neutral current reaction. This report demonstrates a coincidence technique to identify neutrons emitted from the 252 Cf neutron calibration source. The source releases on average four neutrons when a 252 Cf nucleus spontaneously fissions. Each neutron is detected as a separate event when the neutron is captured by a deuteron, releasing a gamma ray of approximately 6.25 MeV. This gamma ray is in turn detected by the photomultiplier tube (PMT) array. By investigating the time and spatial separation between neutron-like events, it is possible to obtain a pure sample of neutrons for calibration study. Preliminary results of the technique applied to two calibration runs are presented

Neutron in biology

Energy Technology Data Exchange (ETDEWEB)

Niimura, Nobuo [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1997-11-01

Neutron in biology can provide an experimental method of directly locating relationship of proteins and DNA. However, there are relatively few experimental study of such objects since it takes a lot of time to collect a sufficient number of Bragg reflections and inelastic spectra due to the low flux of neutron illuminating the sample. Since a next generation neutron source of JAERI will be 5MW spallation neutron source and its effective neutron flux will be 10{sup 2} to 10{sup 3} times higher than the one of JRR-3M, neutron in biology will open a completely new world for structural biology. (author)

Reactor neutron dosimetry

International Nuclear Information System (INIS)

Najzer, M.; Pauko, M.; Glumac, B.; Acquah, I.N.; Moskon, F.

1977-01-01

An analysis of requirements and possibilities for experimental neutron spectrum determination during the reactor pressure vessel surveil lance programme is given. Fast neutron spectrum and neutron dose rate were measured in the Fast neutron irradiation facility of our TRIGA reactor. It was shown that the facility can be used for calibration of neutron dosimeters and for irradiation of samples sensitive to neutron radiation. The investigation of the unfolding algorithm ITER was continued. Based on this investigations are two specialized unfolding program packages ITERAD and ITERGS written this year. They are able to unfold data from activation detectors and NaI(T1) gamma spectrometer respectively

Neutron spectrum for neutron capture therapy in boron; Espectro de neutrones para terapia por captura de neutrones en boro

Energy Technology Data Exchange (ETDEWEB)

Medina C, D.; Soto B, T. G. [Universidad Autonoma de Zacatecas, Unidad Academica de Estudios Nucleares, Programa de Doctorado en Ciencias Basicas, 98068 Zacatecas, Zac. (Mexico); Baltazar R, A. [Universidad Autonoma de Zacatecas, Unidad Academica de Ingenieria Electrica, Programa de Doctorado en Ingenieria y Tecnologia Aplicada, 98068 Zacatecas, Zac. (Mexico); Vega C, H. R., E-mail: dmedina_c@hotmail.com [Universidad Autonoma de Zacatecas, Unidad Academica de Estudios Nucleares, Cipres No. 10, Fracc. La Penuela, 98068 Zacatecas, Zac. (Mexico)

2016-10-15

Glioblastoma multiforme is the most common and aggressive of brain tumors and is difficult to treat by surgery, chemotherapy or conventional radiation therapy. One treatment alternative is the Neutron Capture Therapy in Boron, which requires a beam modulated in neutron energy and a drug with {sup 10}B able to be fixed in the tumor. When the patients head is exposed to the neutron beam, they are captured by the {sup 10}B and produce a nucleus of {sup 7}Li and an alpha particle whose energy is deposited in the cancer cells causing it to be destroyed without damaging the normal tissue. One of the problems associated with this therapy is to have an epithermal neutrons flux of the order of 10{sup 9} n/cm{sup 2}-sec, whereby irradiation channels of a nuclear research reactor are used. In this work using Monte Carlo methods, the neutron spectra obtained in the radial irradiation channel of the TRIGA Mark III reactor are calculated when inserting filters whose position and thickness have been modified. From the arrangements studied, we found that the Fe-Cd-Al-Cd polyethylene filter yielded a ratio between thermal and epithermal neutron fluxes of 0.006 that exceeded the recommended value (<0.05), and the dose due to the capture gamma rays is lower than the dose obtained with the other arrangements studied. (Author)

Characteristics of Fabricated SiC Neutron Detectors for Neutron Flux Monitoring

Energy Technology Data Exchange (ETDEWEB)

Kim, Han Soo; Ha, Jang Ho; Park, Se Hwan; Lee, Kyu Hong [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Lee, Cheol Ho [Hanyang University, Seoul (Korea, Republic of)

2011-05-15

An SPND (Self-powered Neutron Detector) is commonly used for neutron detection in NPP (Nuclear Power Plant) by virtue of un-reactivity for gamma-rays. But it has a drawback, which is that it cannot detect neutrons in real time due to beta emissions (about > 48 s) after reactions between neutrons and {sup 103}Rh in an SPND. And Generation IV reactors such as MSR (Molten-salt reactor), SFR (Sodium-cooled fast reactor), and GFR (Gas-cooled fast reactor) are designed to compact size and integration type. For GEN IV reactor, neutron monitor also must be compact-sized to apply such reactor easily and much more reliable. The wide band-gap semiconductors such as SiC, AlN, and diamond make them an attractive alternative in applications in harsh environments by virtue of the lower operating voltage, faster charge-collection times compared with gas-filled detectors, and compact size.1) In this study, two PIN-type SiC semiconductor neutron detectors, which are for fast neutron detection by elastic and inelastic scattering SiC atoms and for thermal neutron detection by charged particle emissions of 6LiF reaction, were designed and fabricated for NPP-related applications. Preliminary tests such as I-V and alpha response were performed and neutron responses at ENF in HANARO research reactor were also addressed. The application feasibility of the fabricated SiC neutron detector as an in-core neutron monitor was discussed

Measuring neutron spectra in radiotherapy using the nested neutron spectrometer

Energy Technology Data Exchange (ETDEWEB)

Maglieri, Robert, E-mail: robert.maglieri@mail.mcgill.ca; Evans, Michael; Seuntjens, Jan; Kildea, John [Medical Physics Unit, McGill University, Montreal, Quebec H4A 3J1 (Canada); Licea, Angel [Canadian Nuclear Safety Commission, Ottawa, Ontario K1P 5S9 (Canada)

2015-11-15

Purpose: Out-of-field neutron doses resulting from photonuclear interactions in the head of a linear accelerator pose an iatrogenic risk to patients and an occupational risk to personnel during radiotherapy. To quantify neutron production, in-room measurements have traditionally been carried out using Bonner sphere systems (BSS) with activation foils and TLDs. In this work, a recently developed active detector, the nested neutron spectrometer (NNS), was tested in radiotherapy bunkers. Methods: The NNS is designed for easy handling and is more practical than the traditional BSS. Operated in current-mode, the problem of pulse pileup due to high dose-rates is overcome by measuring current, similar to an ionization chamber. In a bunker housing a Varian Clinac 21EX, the performance of the NNS was evaluated in terms of reproducibility, linearity, and dose-rate effects. Using a custom maximum-likelihood expectation–maximization algorithm, measured neutron spectra at various locations inside the bunker were then compared to Monte Carlo simulations of an identical setup. In terms of dose, neutron ambient dose equivalents were calculated from the measured spectra and compared to bubble detector neutron dose equivalent measurements. Results: The NNS-measured spectra for neutrons at various locations in a treatment room were found to be consistent with expectations for both relative shape and absolute magnitude. Neutron fluence-rate decreased with distance from the source and the shape of the spectrum changed from a dominant fast neutron peak near the Linac head to a dominant thermal neutron peak in the moderating conditions of the maze. Monte Carlo data and NNS-measured spectra agreed within 30% at all locations except in the maze where the deviation was a maximum of 40%. Neutron ambient dose equivalents calculated from the authors’ measured spectra were consistent (one standard deviation) with bubble detector measurements in the treatment room. Conclusions: The NNS may

Neutron recognition in the LAND detector for large neutron multiplicity

Energy Technology Data Exchange (ETDEWEB)

Pawlowski, P., E-mail: piotr.pawlowski@ifj.edu.pl [Institute of Nuclear Physics, PAN, Radzikowskiego 152, 31-342 Krakow (Poland); Brzychczyk, J. [Institute of Physics, Jagiellonian University, Reymonta 4, 30-059 Krakow (Poland); Leifels, Y.; Trautmann, W. [GSI Helmholtzzentrum fuer Schwerionenforschung GmbH, D-64291 Darmstadt (Germany); Adrich, P. [National Centre for Nuclear Research, PL-00681 Warsaw (Poland); GSI Helmholtzzentrum fuer Schwerionenforschung GmbH, D-64291 Darmstadt (Germany); Aumann, T. [GSI Helmholtzzentrum fuer Schwerionenforschung GmbH, D-64291 Darmstadt (Germany); Bacri, C.O. [Institut de Physique Nucleaire, IN2P3-CNRS et Universite, F-91406 Orsay (France); Barczyk, T. [Institute of Physics, Jagiellonian University, Reymonta 4, 30-059 Krakow (Poland); Bassini, R. [Istituto di Scienze Fisiche, Universita degli Studi and INFN, I-20133 Milano (Italy); Bianchin, S. [GSI Helmholtzzentrum fuer Schwerionenforschung GmbH, D-64291 Darmstadt (Germany); Boiano, C. [Istituto di Scienze Fisiche, Universita degli Studi and INFN, I-20133 Milano (Italy); Boretzky, K. [GSI Helmholtzzentrum fuer Schwerionenforschung GmbH, D-64291 Darmstadt (Germany); Boudard, A. [IRFU/SPhN, CEA/Saclay, F-91191 Gif-sur-Yvette (France); Chbihi, A. [GANIL, CEA et IN2P3-CNRS, F-14076 Caen (France); Cibor, J.; Czech, B. [Institute of Nuclear Physics, PAN, Radzikowskiego 152, 31-342 Krakow (Poland); De Napoli, M. [Dipartimento di Fisica e Astronomia-Universita and INFN-CT and LNS, I-95123 Catania (Italy); and others

2012-12-01

The performance of the LAND neutron detector is studied. Using an event-mixing technique based on one-neutron data obtained in the S107 experiment at the GSI laboratory, we test the efficiency of various analytic tools used to determine the multiplicity and kinematic properties of detected neutrons. A new algorithm developed recently for recognizing neutron showers from spectator decays in the ALADIN experiment S254 is described in detail. Its performance is assessed in comparison with other methods. The properties of the observed neutron events are used to estimate the detection efficiency of LAND in this experiment.

Nanosecond neutron generator

International Nuclear Information System (INIS)

Lobov, S.I.; Pavlovskaya, N.G.; Pukhov, S.P.

1991-01-01

High-voltage nanosecond neutron generator for obtaining neutrons in D-T reaction is described. Yield of 6x10 6 neutron/pulse was generated in a sealed gas-filled diode with a target on the cathode by accelerating pulse voltage of approximately 0.5 MV and length at half-height of 0.5 ns and deuterium pressure of 6x10 -2 Torr. Ways of increasing neutron yield and possibilities of creating generators of nanosecond neutron pulses with great service life are considered

Neutron transport

International Nuclear Information System (INIS)

Berthoud, Georges; Ducros, Gerard; Feron, Damien; Guerin, Yannick; Latge, Christian; Limoge, Yves; Santarini, Gerard; Seiler, Jean-Marie; Vernaz, Etienne; Coste-Delclaux, Mireille; M'Backe Diop, Cheikh; Nicolas, Anne; Andrieux, Catherine; Archier, Pascal; Baudron, Anne-Marie; Bernard, David; Biaise, Patrick; Blanc-Tranchant, Patrick; Bonin, Bernard; Bouland, Olivier; Bourganel, Stephane; Calvin, Christophe; Chiron, Maurice; Damian, Frederic; Dumonteil, Eric; Fausser, Clement; Fougeras, Philippe; Gabriel, Franck; Gagnier, Emmanuel; Gallo, Daniele; Hudelot, Jean-Pascal; Hugot, Francois-Xavier; Dat Huynh, Tan; Jouanne, Cedric; Lautard, Jean-Jacques; Laye, Frederic; Lee, Yi-Kang; Lenain, Richard; Leray, Sylvie; Litaize, Olivier; Magnaud, Christine; Malvagi, Fausto; Mijuin, Dominique; Mounier, Claude; Naury, Sylvie; Nicolas, Anne; Noguere, Gilles; Palau, Jean-Marc; Le Pallec, Jean-Charles; Peneliau, Yannick; Petit, Odile; Poinot-Salanon, Christine; Raepsaet, Xavier; Reuss, Paul; Richebois, Edwige; Roque, Benedicte; Royer, Eric; Saint-Jean, Cyrille de; Santamarina, Alain; Serot, Olivier; Soldevila, Michel; Tommasi, Jean; Trama, Jean-Christophe; Tsilanizara, Aime; Behar, Christophe; Provitina, Olivier; Lecomte, Michael; Forestier, Alain; Bender, Alexandra; Parisot, Jean-Francois; Finot, Pierre

2013-10-01

This bibliographical note presents a reference book which addresses the study of neutron transport in matter, the study of conditions for a chain reaction and the study of modifications of matter composition due to nuclear reactions. This book presents the main nuclear data, their measurement, assessment and processing, and the spallation. It proposes an overview of methods applied for the study of neutron transport: basic equations and their derived forms, deterministic methods and Monte Carlo method of resolution of the Boltzmann equation, methods of resolution of generalized Bateman equations, methods of time resolution of space kinetics coupled equations. It presents the main calculation codes, discusses the qualification and experimental aspects, and gives an overview of neutron transport applications: neutron transport calculation of reactors, neutron transport coupled with other disciplines, physics of fuel cycle, criticality

Dynamically Polarized Sample for Neutron Scattering At the Spallation Neutron Source

International Nuclear Information System (INIS)

Pierce, Josh; Zhao, J. K.; Crabb, Don

2009-01-01

The recently constructed Spallation Neutron Source at the Oak Ridge National Laboratory is quickly becoming the world's leader in neutron scattering sciences. In addition to the world's most intense pulsed neutron source, we are continuously constructing state of the art neutron scattering instruments as well as sample environments to address today and tomorrow's challenges in materials research. The Dynamically Polarized Sample project at the SNS is aimed at taking maximum advantage of polarized neutron scattering from polarized samples, especially biological samples that are abundant in hydrogen. Polarized neutron scattering will allow us drastically increase the signal to noise ratio in experiments such as neutron protein crystallography. The DPS project is near completion and all key components have been tested. Here we report the current status of the project.

Neutron response study

International Nuclear Information System (INIS)

Endres, G.W.R.; Fix, J.J.; Thorson, M.R.; Nichols, L.L.

1981-01-01

Neutron response of the albedo type dosimeter is strongly dependent on the energy of the incident neutrons as well as the moderating material on the backside of the dosimeter. This study characterizes the response of the Hanford dosimeter for a variety of neutron energies for both a water and Rando phantom (a simulated human body consisting of an actual human skeleton with plastic for body muscles and certain organs). The Hanford dosimeter response to neutrons of different energies is typical of albedo type dosimeters. An approximate two orders of magnitude difference in response is observed between neutron energies of 100 keV and 10 MeV. Methods were described to compensate for the difference in dosimeter response between a laboratory neutron spectrum and the different spectra encountered at various facilities in the field. Generally, substantial field support is necessary for accurate neutron dosimetry

Variability in Light Use Efficiency With Changes in Vegetation Structure and Understory, Using a Temporally Changing Flux Footprint at the BERMS Old Jack Pine Site

Science.gov (United States)

Chasmer, L.; Barr, A.; Black, A.; Hopkinson, C.; Kljun, N.; McCaughey, H.; Treitz, P.; Shashkov, A.; Zha, T.

2006-12-01

Satellite remote sensing algorithms of vegetation gross primary productivity (GPP) often include a light use efficiency (LUE) term that varies depending on meteorological constraints and biome type. LUE is defined as the carbon fixed per mole of photosynthetically active radiation (PAR) absorbed by the canopy (APAR). LUE estimated using GPP from eddy covariance data is complex and changes over short time periods as the available resources (soil moisture, light, temperature, and nitrogen) vary. An understanding of the variability in LUE will improve local to regional estimates of GPP within complex vegetated land cover types using the variety of remote sensing technologies now available. This study examines variability in LUE and GPP at a mature jack pine site within the Fluxnet-Canada BERMS (Boreal Ecosystem Research and Monitoring Sites) study area using a flux footprint model (Kljun et al. 2004) and airborne lidar data (e.g. Chasmer et al. 2006). Three separate weeks of high frequency eddy covariance data are analyzed for June, July, and August 2002 to capture changes in photosynthesis and carbon uptake through the growing season with variations in precipitation and soil moisture. Footprint estimates are derived in half-hourly resolution to provide information on the spatial and temporal variation of the sources of measured C-fluxes. Airborne lidar directly samples ground topography and vegetation structure (i.e., canopy and understory height, gaps between trees, base of canopy), and may provide information on soil moisture and drainage at the ground surface via absorbed and reflected laser pulse energy. Two questions will be addressed specific to net ecosystem productivity (NEP) of the site as a whole, including parts of the ecosystem that may not be properly represented using eddy covariance techniques. These are: 1. How does C uptake and respiration spatially and temporally vary across the jack pine site? 2. How do vegetation characteristics vary with

Basic of Neutron NDA

Energy Technology Data Exchange (ETDEWEB)

Trahan, Alexis Chanel [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-09-15

The objectives of this presentation are to introduce the basic physics of neutron production, interactions and detection; identify the processes that generate neutrons; explain the most common neutron mechanism, spontaneous and induced fission and (a,n) reactions; describe the properties of neutron from different sources; recognize advantages of neutron measurements techniques; recognize common neutrons interactions; explain neutron cross section measurements; describe the fundamental of ³He detector function and designs; and differentiate between passive and active assay techniques.

A study on the utilization of hyper-thermal neutrons for neutron capture therapy

International Nuclear Information System (INIS)

Sakurai, Yoshinori; Kobayashi, Tooru; Kanda, Keiji

1993-01-01

The utilization of hyper-thermal neutrons, which have an energy spectrum of a Maxwellian distribution of a higher temperature than the room temperature of 300 K, was studied in order to improve the thermal neutron flux distribution at the deeper part in a living body for neutron capture therapy. Simulation calculations were carried out using MCNP-V3 in order to confirm the characteristics of hyper-thermal neutrons, i.e., (1) depth dependence of neutron energy spectrum, and (2) depth distribution of the reaction rate in a water phantom for materials with 1/v neutron absorption. It is confirmed that the hyper-thermal neutron irradiation can improve the thermal neutron flux distribution in the deeper and wider area in a living body compared with the thermal neutron irradiation. Practically, by the incidence of the hyper-thermal neutrons with a 3000 K Maxwellian distribution, the thermal neutron flux at 5 cm depth can be given about four times larger than by the incidence of the thermal neutrons of 300 K. (author)

Steel research using neutron beam techniques. In-situ neutron diffraction, small-angle neutron scattering and residual stress analysis

International Nuclear Information System (INIS)

Sueyoshi, Hitoshi; Ishikawa, Nobuyuki; Yamada, Katsumi; Sato, Kaoru; Nakagaito, Tatsuya; Matsuda, Hiroshi; Arakaki, Yu; Tomota, Yo

2014-01-01

Recently, the neutron beam techniques have been applied for steel researches and industrial applications. In particular, the neutron diffraction is a powerful non-destructive method that can analyze phase transformation and residual stress inside the steel. The small-angle neutron scattering is also an effective method for the quantitative evaluation of microstructures inside the steel. In this study, in-situ neutron diffraction measurements during tensile test and heat treatment were conducted in order to investigate the deformation and transformation behaviors of TRIP steels. The small-angle neutron scattering measurements of TRIP steels were also conducted. Then, the neutron diffraction analysis was conducted on the high strength steel weld joint in order to investigate the effect of the residual stress distribution on the weld cracking. (author)

First results of micro-neutron tomography by use of a focussing neutron lens

CERN Document Server

Masschaele, B; Cauwels, P; Dierick, M; Jolie, J; Mondelaers, W

2001-01-01

Since the appearance of high flux neutron beams, scientists experimented with neutron radiography. This high beam flux combined with modern neutron to visible light converters leads to the possibility of performing fast neutron micro-tomography. The first results of cold neutron tomography with a neutron lens are presented in this article. Samples are rotated in the beam and the projections are recorded with a neutron camera. The 3D reconstruction is performed with cone beam reconstruction software.

Gamma/neutron competition above the neutron separation energy in delayed neutron emitters

Directory of Open Access Journals (Sweden)

Valencia E.

2014-03-01

Full Text Available To study the β-decay properties of some well known delayed neutron emitters an experiment was performed in 2009 at the IGISOL facility (University of Jyväskylä in Finland using Total Absorption γ-ray Spectroscopy (TAGS technique. The aim of these measurements is to obtain the full β-strength distribution below the neutron separation energy (Sn and the γ/neutron competition above. This information is a key parameter in nuclear technology applications as well as in nuclear astrophysics and nuclear structure. Preliminary results of the analysis show a significant γ-branching ratio above Sn.

Nuclear reactor neutron shielding

Science.gov (United States)

Speaker, Daniel P; Neeley, Gary W; Inman, James B

2017-09-12

A nuclear reactor includes a reactor pressure vessel and a nuclear reactor core comprising fissile material disposed in a lower portion of the reactor pressure vessel. The lower portion of the reactor pressure vessel is disposed in a reactor cavity. An annular neutron stop is located at an elevation above the uppermost elevation of the nuclear reactor core. The annular neutron stop comprises neutron absorbing material filling an annular gap between the reactor pressure vessel and the wall of the reactor cavity. The annular neutron stop may comprise an outer neutron stop ring attached to the wall of the reactor cavity, and an inner neutron stop ring attached to the reactor pressure vessel. An excore instrument guide tube penetrates through the annular neutron stop, and a neutron plug comprising neutron absorbing material is disposed in the tube at the penetration through the neutron stop.

Development of neutron detectors for neutron scattering experiments

Energy Technology Data Exchange (ETDEWEB)

Moon, Myungkook; Kim, Jongyul; Kim, Jeong ho; Lee, Suhyun [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Lee, Changhwy [Korea Research Institute of Ships and Ocean Engineering, Daejeon (Korea, Republic of)

2015-10-15

Various kinds of detectors are used in accordance with the experimental purpose, such as zero dimensional detector, 1-D or 2-D position-sensitive detectors. Most of neutron detectors use He-3 gas because of its high neutron sensitivity. Since the He-3 supply shortage took place in early 2010, various He-3 alternative detectors have been developed even for the other neutron application. We have developed a new type alternative detector on the basis of He-3 detector technology. Although B- 10 has less neutron detection efficiency compared with He-3, it can be covered by the use of multiple B-10 layers. In this presentation, we would like to introduce the neutron detectors under development and developed detectors. Various types of detector were successfully developed and result of the technical test performance is promising. Even though the detection efficiency of the B-10 detector lower than He-3 one, the continuous research and development is needed for currently not available He-3.

Fundamental neutron physics at a 1 MW long pulse spallation neutron source

International Nuclear Information System (INIS)

Greene, G.L.

1995-01-01

Modern neutron sources and modern neutron science share a common origin in mid twentieth century scientific investigations concerned with the study of the fundamental interactions between elementary particles. Since the time of that common origin, neutron science and the study of elementary particles have evolved into quite disparate disciplines. The neutron became recognized as a powerful tool for the study of condensed matter with modern neutron sources being primarily used (and primarily justified) as tools for condensed matter research. The study of elementary particles has, of course, led to the development of rather different tools and is now dominated by activities carried out at extremely high energies. Notwithstanding this trend, the study of fundamental interactions using neutrons has continued and remains a vigorous activity at many contemporary neutron sources. This research, like neutron scattering research, has benefited enormously by the development of modern high flux neutron facilities. Future sources, particularly high power spallation sources, offer exciting possibilities for the continuation of this program of research

Powder neutron diffractometers

International Nuclear Information System (INIS)

Adib, M.

2002-01-01

Basic properties and applications of powder neutron Diffractometers are described for optimum use of the continuous neutron beams. These instruments are equipped with position sensitive detectors, neutron guide tubes, and both high intensity and high resolution modes of operation are possible .The principles of both direct and Fourier reverse time-of-flight neutron Diffractometers are also given

Polycapillary neutron lenses

International Nuclear Information System (INIS)

Mildner, D.F.R.

1997-01-01

The principle of multiple mirror reflection from smooth surfaces at small grazing angles enables the transport and guiding of high intensity slow neutron beams to locations of low background for neutron scattering and absorption experiments and to provide facilities for multiple instruments. Curved guides have been widely used at cold neutron facilities to remove the unwanted radiation (fast neutrons and gamma rays) from the beam without the use of filters. A typical guide has transverse dimensions of 50 mm and, with a radius of curvature of 1 km, transmits wavelengths longer than 5 A. Much tighter curves requires narrower transverse dimensions, otherwise there is little transmission. Typical neutron benders have a number of slots with transverse dimensions of ∼5 mm. Based on the same principle but using a different technology, recent developments in glass polycapillary fibers have produced miniature versions of neutron guides. Fibers with many thousands of channels having sizes of ∼ 10 μm enable beams of long wavelength neutrons (λ > 4 A) to be transmitted efficiently in a radius of curvature as small as a fraction of 1 m. A large collection of these miniature versions of neutron guides can be used to bend the neutron trajectories such that the incident beam can be focused. (author)

Neutron structural biology

Energy Technology Data Exchange (ETDEWEB)

Niimura, Nobuo [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1998-03-01

Neutron diffraction provides an experimental method of directly locating hydrogen atoms in protein which play important roles in physiological functions. However, there are relatively few examples of neutron crystallography in biology since it takes a lot of time to collect a sufficient number of Bragg reflections due to the low flux of neutrons illuminating the sample. In order to overcome the flux problem, we have successfully developed the neutron IP, where the neutron converter, {sup 6}Li or Gd, was mixed with a photostimulated luminescence material on flexible plastic support. Neutron Laue diffraction 2A data from tetragonal lysozyme were collected for 10 days with neutron imaging plates, and 960 hydrogen atoms in the molecule and 157 bound water molecules were identified. These results explain the proposed hydrolysis mechanism of the sugar by the lysozyme molecule and that lysozyme is less active at pH7.0. (author)

Neutron exposure

International Nuclear Information System (INIS)

Prillinger, G.; Konynenburg, R.A. van

1998-01-01

As a result of the popularity of the Agencies report 'Neutron Irradiation Embrittlement of Reactor Pressure Vessel Steels' of 1975, it was decided that another report on this broad subject would be of use. In this report, background and contemporary views on specially identified areas of the subject are considered as self-contained chapters, written by experts. In chapter 6, LWR-PV neutron transport calculations and dosimetry methods and how they are combined to evaluate the neutron exposure of the steel of pressure vessels are discussed. An effort to correlate neutron exposure parameters with damage is made

Atmospheric neutrons

International Nuclear Information System (INIS)

Preszler, A.M.; Moon, S.; White, R.S.

1976-01-01

Additional calibrations of the University of California double-scatter neutron and additional analysis corrections lead to the slightly changed neutron fluxes reported here. The theoretical angular distributions of Merker (1975) are in general agreement with our experimental fluxes but do not give the peaks for vertical upward and downward moving neutrons. The theoretical neutron escape current J 2 /sub pi/ (Merker, 1972; Armstrong et al., 1973) is in agreement with the experimental values from 10 to 100 MeV. Our experimental fluxes agree with those of the Kanbach et al. (1974) in the overlap region from 70 to 100 MeV

Study on neutron irradiation behavior of beryllium as neutron multiplier

Energy Technology Data Exchange (ETDEWEB)

Ishitsuka, Etsuo [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment

1998-03-01

More than 300 tons beryllium is expected to be used as a neutron multiplier in ITER, and study on the neutron irradiation behavior of beryllium as the neutron multiplier with Japan Materials Testing Reactor (JMTR) were performed to get the engineering data for fusion blanket design. This study started as the study on the tritium behavior in beryllium neutron reflector in order to make clear the generation mechanism on tritium of JMTR primary coolant since 1985. These experiences were handed over to beryllium studies for fusion study, and overall studies such as production technology of beryllium pebbles, irradiation behavior evaluation and reprocessing technology have been started since 1990. In this presentation, study on the neutron irradiation behavior of beryllium as the neutron multiplier with JMTR was reviewed from the point of tritium release, thermal properties, mechanical properties and reprocessing technology. (author)

Neutron source

International Nuclear Information System (INIS)

Cason, J.L. Jr.; Shaw, C.B.

1975-01-01

A neutron source which is particularly useful for neutron radiography consists of a vessel containing a moderating media of relatively low moderating ratio, a flux trap including a moderating media of relatively high moderating ratio at the center of the vessel, a shell of depleted uranium dioxide surrounding the moderating media of relatively high moderating ratio, a plurality of guide tubes each containing a movable source of neutrons surrounding the flux trap, a neutron shield surrounding one part of each guide tube, and at least one collimator extending from the flux trap to the exterior of the neutron source. The shell of depleted uranium dioxide has a window provided with depleted uranium dioxide shutters for each collimator. Reflectors are provided above and below the flux trap and on the guide tubes away from the flux trap

Neutron cooling and cold-neutron sources (1962)

International Nuclear Information System (INIS)

Jacrot, B.

1962-01-01

Intense cold-neutron sources are useful in studying solids by the inelastic scattering of neutrons. The paper presents a general survey covering the following aspects: a) theoretical considerations put forward by various authors regarding thermalization processes at very low temperatures; b) the experiments that have been carried out in numerous laboratories with a view to comparing the different moderators that can be used; c) the cold neutron sources that have actually been produced in reactors up to the present time, and the results obtained with them. (author) [fr

High energy neutron radiography

International Nuclear Information System (INIS)

Gavron, A.; Morley, K.; Morris, C.; Seestrom, S.; Ullmann, J.; Yates, G.; Zumbro, J.

1996-01-01

High-energy spallation neutron sources are now being considered in the US and elsewhere as a replacement for neutron beams produced by reactors. High-energy and high intensity neutron beams, produced by unmoderated spallation sources, open potential new vistas of neutron radiography. The authors discuss the basic advantages and disadvantages of high-energy neutron radiography, and consider some experimental results obtained at the Weapons Neutron Research (WNR) facility at Los Alamos

Intense fusion neutron sources

International Nuclear Information System (INIS)

Kuteev, B. V.; Goncharov, P. R.; Sergeev, V. Yu.; Khripunov, V. I.

2010-01-01

The review describes physical principles underlying efficient production of free neutrons, up-to-date possibilities and prospects of creating fission and fusion neutron sources with intensities of 10 15 -10 21 neutrons/s, and schemes of production and application of neutrons in fusion-fission hybrid systems. The physical processes and parameters of high-temperature plasmas are considered at which optimal conditions for producing the largest number of fusion neutrons in systems with magnetic and inertial plasma confinement are achieved. The proposed plasma methods for neutron production are compared with other methods based on fusion reactions in nonplasma media, fission reactions, spallation, and muon catalysis. At present, intense neutron fluxes are mainly used in nanotechnology, biotechnology, material science, and military and fundamental research. In the near future (10-20 years), it will be possible to apply high-power neutron sources in fusion-fission hybrid systems for producing hydrogen, electric power, and technological heat, as well as for manufacturing synthetic nuclear fuel and closing the nuclear fuel cycle. Neutron sources with intensities approaching 10 20 neutrons/s may radically change the structure of power industry and considerably influence the fundamental and applied science and innovation technologies. Along with utilizing the energy produced in fusion reactions, the achievement of such high neutron intensities may stimulate wide application of subcritical fast nuclear reactors controlled by neutron sources. Superpower neutron sources will allow one to solve many problems of neutron diagnostics, monitor nano-and biological objects, and carry out radiation testing and modification of volumetric properties of materials at the industrial level. Such sources will considerably (up to 100 times) improve the accuracy of neutron physics experiments and will provide a better understanding of the structure of matter, including that of the neutron itself.

Intense fusion neutron sources

Science.gov (United States)

Kuteev, B. V.; Goncharov, P. R.; Sergeev, V. Yu.; Khripunov, V. I.

2010-04-01

The review describes physical principles underlying efficient production of free neutrons, up-to-date possibilities and prospects of creating fission and fusion neutron sources with intensities of 1015-1021 neutrons/s, and schemes of production and application of neutrons in fusion-fission hybrid systems. The physical processes and parameters of high-temperature plasmas are considered at which optimal conditions for producing the largest number of fusion neutrons in systems with magnetic and inertial plasma confinement are achieved. The proposed plasma methods for neutron production are compared with other methods based on fusion reactions in nonplasma media, fission reactions, spallation, and muon catalysis. At present, intense neutron fluxes are mainly used in nanotechnology, biotechnology, material science, and military and fundamental research. In the near future (10-20 years), it will be possible to apply high-power neutron sources in fusion-fission hybrid systems for producing hydrogen, electric power, and technological heat, as well as for manufacturing synthetic nuclear fuel and closing the nuclear fuel cycle. Neutron sources with intensities approaching 1020 neutrons/s may radically change the structure of power industry and considerably influence the fundamental and applied science and innovation technologies. Along with utilizing the energy produced in fusion reactions, the achievement of such high neutron intensities may stimulate wide application of subcritical fast nuclear reactors controlled by neutron sources. Superpower neutron sources will allow one to solve many problems of neutron diagnostics, monitor nano-and biological objects, and carry out radiation testing and modification of volumetric properties of materials at the industrial level. Such sources will considerably (up to 100 times) improve the accuracy of neutron physics experiments and will provide a better understanding of the structure of matter, including that of the neutron itself.

Thermal neutron flux measurements using neutron-electron converters; Mesure de flux de neutrons thermiques avec des convertisseurs neutrons electrons

Energy Technology Data Exchange (ETDEWEB)

Le Meur, R; Lecomte, P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1968-07-01

The operation of neutron-electron converters designed for measuring thermal neutron fluxes is examined. The principle is to produce short lived isotopes emitting beta particles, by activation, and to measure their activity not by extracting them from the reactor, but directly in the reactor using the emitted electrons to deflect the needle of a galvanometer placed outside the flux. After a theoretical study, the results of the measurements are presented; particular attention is paid to a new type of converter characterized by a layer structure. The converters are very useful for obtaining flux distributions with more than 10{sup 7} neutrons cm{sup -2}*sec{sup -1}. They work satisfactorily in pressurized carbon dioxide at 400 Celsius degrees. Some points still have to be cleared up however concerning interfering currents in the detectors and the behaviour of the dielectrics under irradiation. (authors) [French] On examine le fonctionnement de convertisseurs neutrons electrons destines a des mesures de flux de neutrons thermiques. Le principe est de former par activation des isotopes a periodes courtes et a emission beta et de mesurer leur activite non pas en les sortant du reacteur, mais directement en pile, utilisant les electrons emis pour faire devier l'aiguille d'un galvanometre place hors flux. Apres une etude theorique, on indique des resultats de mesures obtenus, en insistant particulierement sur un nouveau type de convertisseur, caracterise par sa structure stratifiee. Les convertisseurs sont tres interessants pour tracer, des cartes de flux a partir de 10{sup 7} neutrons cm{sup -2}*s{sup -1}. Ils sont utilisables pour des flux de 10{sup 14} neutrons cm{sup -2}*s{sup -1}. Ils fonctionnent correctement dans du gaz carbonique sous pression a 400 C. Des points restent cependant a eclaircir concernant les courants parasites dans les detecteurs et le comportement des dielectriques pendant leur irradiation. (auteur)

Application of MSS-neutron spin echo spectrometer to pulsed neutron sources

International Nuclear Information System (INIS)

Tasaki, S.; Ebisawa, T.; Hino, M.; Kawai, T.

2001-01-01

A multilayer spin splitter (MSS) is a neutron device that gives phase difference between field-parallel and -antiparallel spin component of a superposing state. Since the phase difference is equivalent to the Larmor precession angle, MSS enables us to construct a new type of neutron spin echo (NSE) spectrometer. The new NSE spectrometer has its properties that 1. since the phase shift is neutron flight path length, the spectrometer can be drastically small, 2. the neutron spin echo time is proportional to the neutron wavelength. (author)

Neutron Research in HANARO

International Nuclear Information System (INIS)

Kim, Hark Rho

2005-01-01

HANARO (High-flux Advanced Neutron Application Reactor), which was designed and constructed by indigenous technology, is a world-class multi-purpose research reactor with a design thermal power of 30 MW, providing high neutron flux for various applications in Korea. HANARO has been operated since its first criticality in February 1995, and is now successfully utilized in such areas as neutron beam research, fuel and materials tests, radioisotopes and radiopharmaceuticals production, neutron activation analysis, and neutron transmutation doping, etc. A number of experimental facilities have been developed and installed since the beginning of reactor operation, and R and D activities for installing more facilities are actively under progress. Three flux traps in the core (CT, IR1, IR2), providing a high fast neutron flux, can be used for materials and fuel irradiation tests. They are also proper for production of high specific activity radioisotopes. Four vertical holes in the outer core region, abundant in epithermal neutrons, are used for fuel or material tests and radioisotope production. In the heavy water reflector region, 25 vertical holes with high quality thermal neutrons are located for radioisotope production, neutron activation analysis, neutron transmutation doping and cold neutron source installation. The two largest holes named NTD1 and NTD2 are for neutron transmutation doping, CNS for the cold neutron source installation, and LH for the irradiation of large targets. The high resolution powder diffractometer (HRPD) became operational in 1998, followed by the four circle diffractometer (FCD) in 1999, the residual stress instrument (RSI) in 2000, and the small angle neutron spectrometer (SANS) in 2001, respectively. HRPD and SANS became the most popular instruments these days, attracting wide range of users from academia, institutes and industries. We have made a lot of efforts during the last 10 years to develop some key components such as

Neutron capture therapy with thermal neutrons at IRT MIFI

International Nuclear Information System (INIS)

Zajtsev, K.N.; Portnov, A.A.; Savkin, V.A.; Kulakov, V.N.; Khokhlov, V.F.; Shejno, I.N.; Vajnson, A.A.; Kozlovskaya, N.G.; Meshcherikova, V.V.; Mitin, V.N.; Yarmonenko, S.P.

2001-01-01

Combined preclinical investigations into neutron capture therapy are conducted. Malignant melanoma was adopted as the line of investigation; boron-containing and gadolinium-containing preparations were used during the neutron capture therapy working off. Preparations produce secondary varying radiations when used in tumor. Dogs with spontaneous melanoma were used for the experiments. Procedures for the irradiation of dogs by neutron beam as the stage before use for the treatment of oncology patients were finished off; efficiency of neutron beam influence on normal tissues during the irradiation of dogs with melanoma (and without it) in antitumor and side effect sense was estimated [ru

Compact neutron generator

Science.gov (United States)

Leung, Ka-Ngo; Lou, Tak Pui

2005-03-22

A compact neutron generator has at its outer circumference a toroidal shaped plasma chamber in which a tritium (or other) plasma is generated. A RF antenna is wrapped around the plasma chamber. A plurality of tritium ion beamlets are extracted through spaced extraction apertures of a plasma electrode on the inner surface of the toroidal plasma chamber and directed inwardly toward the center of neutron generator. The beamlets pass through spaced acceleration and focusing electrodes to a neutron generating target at the center of neutron generator. The target is typically made of titanium tubing. Water is flowed through the tubing for cooling. The beam can be pulsed rapidly to achieve ultrashort neutron bursts. The target may be moved rapidly up and down so that the average power deposited on the surface of the target may be kept at a reasonable level. The neutron generator can produce fast neutrons from a T-T reaction which can be used for luggage and cargo interrogation applications. A luggage or cargo inspection system has a pulsed T-T neutron generator or source at the center, surrounded by associated gamma detectors and other components for identifying explosives or other contraband.

Thermal neutron moderating device

International Nuclear Information System (INIS)

Takigami, Hiroyuki.

1995-01-01

In a thermal neutron moderating device, superconductive coils for generating magnetic fields capable of applying magnetic fields vertical to the longitudinal direction of a thermal neutron passing tube, and superconductive coils for magnetic field gradient for causing magnetic field gradient in the longitudinal direction of the thermal neutron passing tube are disposed being stacked at the outside of the thermal neutron passing tube. When magnetic field gradient is present vertically to the direction of a magnetic moment, thermal neutrons undergo forces in the direction of the magnetic field gradient in proportion to the magnetic moment. Then, the magnetic moment of the thermal neutrons is aligned with the direction vertical to the passing direction of the thermal neutrons, to cause the magnetic field gradient in the passing direction of the thermal neutrons. The speed of the thermal neutrons can be optionally selected and the wavelength can freely be changed by applying forces to the thermal neutrons and changing the extent and direction of the magnetic field gradient. Superconductive coils are used as the coils for generating magnetic fields and the magnetic field gradient in order to change extremely high energy of the thermal neutrons. (N.H.)

Reactor Neutron Sources

International Nuclear Information System (INIS)

Aksenov, V.L.

1994-01-01

The present status and the prospects for development of reactor neutron sources for neutron scattering research in the world are considered. The fields of application of neutron scattering relative to synchrotron radiation, the creation stages of reactors (steady state and pulsed) and their position in comparison with spallation neutron sources at present and in the foreseen future are discussed. (author). 15 refs.; 8 figs.; 3 tabs

Neutron Albedo

CERN Document Server

Ignatovich, V K

2005-01-01

A new, algebraic, method is applied to calculation of neutron albedo from substance to check the claim that use of ultradispersive fuel and moderator of an active core can help to gain in size and mass of the reactor. In a model of isotropic distribution of incident and reflected neutrons it is shown that coherent scattering on separate grains in the case of thermal neutrons increases transport cross section negligibly, however it decreases albedo from a wall of finite thickness because of decrease of substance density. A visible increase of albedo takes place only for neutrons with wave length of the order of the size of a single grain.

Progress report: determinations of the neutron-neutron scattering length ann from kinematically incomplete neutron-deuteron breakup data revisited

International Nuclear Information System (INIS)

Tornow, W.; Braun, R.T.; Witala, H.

1996-01-01

We review published analyses of the final-state-interaction enhancement observed in proton energy distributions obtained from kinematically incomplete neutron-deuteron breakup experiments. We compare the results derived from these analyses for the neutron-neutron scattering length, a nn with our results based on a rigorous treatment of the three-nucleon Faddeev equations in conjunction with the use of realistic nucleon-nucleon potentials. Our values for a nn deviate outside the quoted uncertainties from the ones obtained in the previous analyses where simplified nucleon-nucleon interaction models were employed. In contrast to the previous determinations, the present results for a nn are in clear disagreement with the values for a nn based on π - -deuteron capture experiments. Unless inconsistencies in the experimental neutron-deuteron breakup data at low energies can be resolved and the influence of possible three-nucleon-force effects can be reliably determined, we recommend that one not resort to the kinematically incomplete neutron-deuteron breakup reaction as a tool for determining a quantity as important for nuclear and particle physics as is the neutron-neutron scattering length a nn . (author)

Neutron Flux Distribution on Neutron Radiography Facility After Fixing the Collimator

International Nuclear Information System (INIS)

Supandi; Parikin; Mohtar; Sunardi; Roestam, S

1996-01-01

The Radiography Neutron Facility consists of an inner collimator, outer collimator, main shutter, second shutter and the sample chamber with 300 mm in diameter. Neutron beam quality depends on the neutron flux intensities distribution, L/D ratio Cd ratio, neutron/gamma ratio. The results show that the neutron flux intensity was 2.83 x 107 n cm-2.s-1, with deviation of + 7.8 % and it was distributed homogeneously at the sample position of 200 mm diameter. The beam characteristics were L/D ratio 98 and Rod 8, and neutron gamma ratio 3.08 x 105n.cm-2.mR-1 and Reactor Power was 20 MW. This technique can be used to examine sample with diameter of < 200 mm

Refractive neutron lens

International Nuclear Information System (INIS)

Petrov, P.V.; Kolchevsky, N.N.

2013-01-01

Model of the refractive neutron lens is proposed. System of N lenses acts as one thin lens with a complex refraction index n*. The maximum number N max of individual lenses for 'thick' neutron lens is calculated. Refractive neutron lens properties (resolution, focal depth) as function of resolution factor F 0 =ρbc/μ and depth of field factor dF 0 =λF 0 =λρbc/μ are calculated. It is shown that micro resolution of the refractive neutron optics is far from the wavelength in size and its open possibilities for progress in refractive neutron optics. (authors)

The neutron

International Nuclear Information System (INIS)

Kredov, B.M.

1979-01-01

The history of the neutron is displayed on the basis of contributions by scientists who produced outstanding results in neutron research (part 1), of summarizing discoveries and theories which led to the discovery of the neutron and the resulting development of nuclear physics (part 2), and of fundamental papers written by Rutherford, Chadwick, Iwanenko, and others (appendix). Of interest to physicists, historians, and students

Prototype Neutron Energy Spectrometer

International Nuclear Information System (INIS)

Mitchell, Stephen; Mukhopadhyay, Sanjoy; Maurer, Richard; Wolff, Ronald

2010-01-01

The project goals are: (1) Use three to five pressurized helium tubes with varying polyethylene moderators to build a neutron energy spectrometer that is most sensitive to the incident neutron energy of interest. Neutron energies that are of particular interest are those from the fission neutrons (typically around 1-2 MeV); (2) Neutron Source Identification - Use the neutron energy 'selectivity' property as a tool to discriminate against other competing processes by which neutrons are generated (viz. Cosmic ray induced neutron production (ship effect), (a, n) reactions); (3) Determine the efficiency as a function of neutron energy (response function) of each of the detectors, and thereby obtain the composite neutron energy spectrum from the detector count rates; and (4) Far-field data characterization and effectively discerning shielded fission source. Summary of the presentation is: (1) A light weight simple form factor compact neutron energy spectrometer ready to be used in maritime missions has been built; (2) Under laboratory conditions, individual Single Neutron Source Identification is possible within 30 minutes. (3) Sources belonging to the same type of origin viz., (a, n), fission, cosmic cluster in the same place in the 2-D plot shown; and (4) Isotopes belonging to the same source origin like Cm-Be, Am-Be (a, n) or Pu-239, U-235 (fission) do have some overlap in the 2-D plot.

Prototype Neutron Energy Spectrometer

Energy Technology Data Exchange (ETDEWEB)

Stephen Mitchell, Sanjoy Mukhopadhyay, Richard Maurer, Ronald Wolff

2010-06-16

The project goals are: (1) Use three to five pressurized helium tubes with varying polyethylene moderators to build a neutron energy spectrometer that is most sensitive to the incident neutron energy of interest. Neutron energies that are of particular interest are those from the fission neutrons (typically around 1-2 MeV); (2) Neutron Source Identification - Use the neutron energy 'selectivity' property as a tool to discriminate against other competing processes by which neutrons are generated (viz. Cosmic ray induced neutron production [ship effect], [a, n] reactions); (3) Determine the efficiency as a function of neutron energy (response function) of each of the detectors, and thereby obtain the composite neutron energy spectrum from the detector count rates; and (4) Far-field data characterization and effectively discerning shielded fission source. Summary of the presentation is: (1) A light weight simple form factor compact neutron energy spectrometer ready to be used in maritime missions has been built; (2) Under laboratory conditions, individual Single Neutron Source Identification is possible within 30 minutes. (3) Sources belonging to the same type of origin viz., (a, n), fission, cosmic cluster in the same place in the 2-D plot shown; and (4) Isotopes belonging to the same source origin like Cm-Be, Am-Be (a, n) or Pu-239, U-235 (fission) do have some overlap in the 2-D plot.

Ramsauer effect in triplet neutron-neutron scattering

International Nuclear Information System (INIS)

Pupyshev, V.V.; Solovtsova, O.P.

1995-01-01

As we show, due to interplay of pure nuclear and magnetic moment interactions, the total cross section of triplet neutron-neutron scattering should possess a non-zero limit at E cm = 0 and a local minimum at ∼ 20 keV. 17 refs., 1 fig

Spectral correction factors for conventional neutron dosemeters used in high-energy neutron environments

International Nuclear Information System (INIS)

Lee, K.W.; Sheu, R.J.

2015-01-01

High-energy neutrons (>10 MeV) contribute substantially to the dose fraction but result in only a small or negligible response in most conventional moderated-type neutron detectors. Neutron dosemeters used for radiation protection purpose are commonly calibrated with 252 Cf neutron sources and are used in various workplace. A workplace-specific correction factor is suggested. In this study, the effect of the neutron spectrum on the accuracy of dose measurements was investigated. A set of neutron spectra representing various neutron environments was selected to study the dose responses of a series of Bonner spheres, including standard and extended-range spheres. By comparing 252 Cf-calibrated dose responses with reference values based on fluence-to-dose conversion coefficients, this paper presents recommendations for neutron field characterisation and appropriate correction factors for responses of conventional neutron dosemeters used in environments with high-energy neutrons. The correction depends on the estimated percentage of high-energy neutrons in the spectrum or the ratio between the measured responses of two Bonner spheres (the 4P6-8 extended-range sphere versus the 6'' standard sphere). (authors)

Neutron activation analysis at the Californium User Facility for Neutron Science

International Nuclear Information System (INIS)

Martin, R.C.; Smith, E.H.; Glasgow, D.C.; Jerde, E.A.; Marsh, D.L.; Zhao, L.

1997-12-01

The Californium User Facility (CUF) for Neutron Science has been established to provide 252 Cf-based neutron irradiation services and research capabilities including neutron activation analysis (NAA). A major advantage of the CUF is its accessibility and controlled experimental conditions compared with those of a reactor environment The CUF maintains the world's largest inventory of compact 252 Cf neutron sources. Neutron source intensities of ≤ 10 11 neutrons/s are available for irradiations within a contamination-free hot cell, capable of providing thermal and fast neutron fluxes exceeding 10 8 cm -2 s -1 at the sample. Total flux of ≥10 9 cm -2 s -1 is feasible for large-volume irradiation rabbits within the 252 Cf storage pool. Neutron and gamma transport calculations have been performed using the Monte Carlo transport code MCNP to estimate irradiation fluxes available for sample activation within the hot cell and storage pool and to design and optimize a prompt gamma NAA (PGNAA) configuration for large sample volumes. Confirmatory NAA irradiations have been performed within the pool. Gamma spectroscopy capabilities including PGNAA are being established within the CUF for sample analysis

A proposed experiment for studying the direct neutron-neutron interaction

International Nuclear Information System (INIS)

Hassan Fikry, A.R.; Maayouf, R.M.A.

1979-01-01

An experiment for studying the direct neutron-neutron interaction is suggested. The experiment is based on the combined use of an accelerator, e.g., an electron linear accelerator, together with a mobile pulsed reactor; or using a pulsed beam reactor together with a mobile neutron generator

Neutron spectrum for neutron capture therapy in boron

International Nuclear Information System (INIS)

Medina C, D.; Soto B, T. G.; Baltazar R, A.; Vega C, H. R.

2016-10-01

Glioblastoma multiforme is the most common and aggressive of brain tumors and is difficult to treat by surgery, chemotherapy or conventional radiation therapy. One treatment alternative is the Neutron Capture Therapy in Boron, which requires a beam modulated in neutron energy and a drug with 10 B able to be fixed in the tumor. When the patients head is exposed to the neutron beam, they are captured by the 10 B and produce a nucleus of 7 Li and an alpha particle whose energy is deposited in the cancer cells causing it to be destroyed without damaging the normal tissue. One of the problems associated with this therapy is to have an epithermal neutrons flux of the order of 10 9 n/cm 2 -sec, whereby irradiation channels of a nuclear research reactor are used. In this work using Monte Carlo methods, the neutron spectra obtained in the radial irradiation channel of the TRIGA Mark III reactor are calculated when inserting filters whose position and thickness have been modified. From the arrangements studied, we found that the Fe-Cd-Al-Cd polyethylene filter yielded a ratio between thermal and epithermal neutron fluxes of 0.006 that exceeded the recommended value (<0.05), and the dose due to the capture gamma rays is lower than the dose obtained with the other arrangements studied. (Author)

Polarized neutron spectrometer

International Nuclear Information System (INIS)

Abov, Yu.G.; Novitskij, V.V.; Alfimenkov, V.P.; Galinskij, E.M.; Mareev, Yu.D.; Pikel'ner, L.B.; Chernikov, A.N.; Lason', L.; Tsulaya, V.M.; Tsulaya, M.I.

2000-01-01

The polarized neutron spectrometer, intended for studying the interaction of polarized neutrons with nuclei and condensed media in the area of energies from thermal up to several electron-volt, is developed at the IBR-2 reactor (JINR, Dubna). Diffraction on the Co(92%)-Fe(8%) magnetized monocrystals is used for the neutron polarization and polarization analysis. The neutron polarization within the whole energy range equals ∼ 95% [ru

Evaluation of room-scattered neutrons at the JNC Tokai neutron reference field

Energy Technology Data Exchange (ETDEWEB)

Yoshida, Tadayoshi; Tsujimura, Norio [Japan Nuclear Cycle Development Inst., Tokai, Ibaraki (Japan). Tokai Works; Oyanagi, Katsumi [Japan Radiation Engineering Co., Ltd., Hitachi, Ibaraki (Japan)

2002-09-01

Neutron reference fields for calibrating neutron-measuring devices in JNC Tokai Works are produced by using radionuclide neutron sources, {sup 241}Am-Be and {sup 252}Cf sources. The reference field for calibration includes scattered neutrons from the material surrounding sources, wall, floor and ceiling of the irradiation room. It is, therefore, necessary to evaluate the scattered neutrons contribution and their energy spectra at reference points. Spectral measurements were performed with a set of Bonner multi-sphere spectrometers and the reference fields were characterized in terms of spectral composition and the fractions of room-scattered neutrons. In addition, two techniques stated in ISO 10647, the shadow-cone method and the polynomial fit method, for correcting the contributions from the room-scattered neutrons to the readings of neutron survey instruments were compared. It was found that the two methods gave an equivalent result within a deviation of 3.3% at a source-to-detector distance from 50cm to 500cm. (author)

Evaluation of room-scattered neutrons at the JNC Tokai neutron reference field

International Nuclear Information System (INIS)

Yoshida, Tadayoshi; Tsujimura, Norio

2002-01-01

Neutron reference fields for calibrating neutron-measuring devices in JNC Tokai Works are produced by using radionuclide neutron sources, 241 Am-Be and 252 Cf sources. The reference field for calibration includes scattered neutrons from the material surrounding sources, wall, floor and ceiling of the irradiation room. It is, therefore, necessary to evaluate the scattered neutrons contribution and their energy spectra at reference points. Spectral measurements were performed with a set of Bonner multi-sphere spectrometers and the reference fields were characterized in terms of spectral composition and the fractions of room-scattered neutrons. In addition, two techniques stated in ISO 10647, the shadow-cone method and the polynomial fit method, for correcting the contributions from the room-scattered neutrons to the readings of neutron survey instruments were compared. It was found that the two methods gave an equivalent result within a deviation of 3.3% at a source-to-detector distance from 50cm to 500cm. (author)

Anti-diabetic Activity of Tabat Barito Leafs (Ficus deltoidea, Jack Extract in Rats

Directory of Open Access Journals (Sweden)

Heru Agus Cahyanto

2013-06-01

Full Text Available Tabat barito (Ficus deltoidea, Jack leaf is believed could be used to treat diabetes. But more scientific data are needed. The aim of this study is to investigate  antidiabetic activity of  Tabat Barito extract by glucose tolerance method. The treatment was given in three doses (50, 100, and 200 mg/kg BW and two controls using aquoeus and glibenklamid.  Tabat barito extract was obtained by maceration and made into dry extract with addition of starch. The result showed that chemical compound of the ethanol extract were fenolic and saponin. The extract showed effects in lowering blood sugar levels with glucose tolerance methods at 30 to 60 minutes. Blood glucose levels of mice treated with the extract extract ranged between 132.60 to 258.00 mg/dL , glibenklamide ranged from 130.20 to 144.60 mg/dL, and aqua ranged between 227.60 to 260.20 mg/dL. The percentage decrease in blood sugar levels compared to controls is 32.54%.

Utilization of low voltage D-T neutron generators in neutron physics studies

International Nuclear Information System (INIS)

Singkarat, S.

1995-01-01

In a small nuclear laboratory of a developing country a low voltage D-T neutron generator can be a very useful scientific apparatus. Such machines have been used successfully for more than 40 years in teaching and scientific research. The original continuous mode 150-kV D-T neutron generator has been modified to have also a capability of producing 2-ns pulsed neutrons. Together with a carefully designed 10 m long flight path collimator and shielding of a 25 cm diameter · 10 cm thick BC-501 neutron detector, the pulsing system was successfully used for measuring the double differential cross-section (DDX) of natural iron for 14.1-MeV neutron from the angle of 30 deg to 150 deg in 10 deg steps. In order to extend the utility of the generator, two methods for converting the almost monoenergetic 14-MeV neutrons to monoenergetic neutrons of lower energy were proposed and tested. Both designs used the neutron-proton interaction at a circular surface-of-revolution made of hydrocarbon materials. The first design is for a pulsed neutron generator and the second design is for an ordinary continuous mode generator. The latter method was successfully used to measure the scintillation light output of a 1.4 cm diameter spherical NE-213 scintillation detector. The neutron generator has also been used in the continuous search for improved neutron detection techniques. There is a proposal, based on Monte Carlo calculations, of using a scintillation fiber for a fast neutron spectrometer. Due to the slender shape of the fiber, the pattern of produced light gives a peak in the pulse height spectrum instead of the well-known rectangular-like distribution, when the fiber is bombarded end-on by a beam of 14-MeV neutrons. Experimental investigations were undertaken. Detailed investigations on the light transportation property of a short fiber were performed. The predicted peak has not yet been found but the fiber detector may be developed as a directional discrimination fast neutron

Pulsed neutron porosity logging system

International Nuclear Information System (INIS)

Smith, H.D. Jr.; Smith, M.P.; Schultz, W.E.

1978-01-01

An improved pulsed neutron porosity logging system is provided in the present invention. A logging tool provided with a 14 MeV pulsed neutron source, an epithermal neutron detector, and a fast neutron detector is moved through a borehole. Repetitive bursts of neutrons irradiate the earth formations and, during the bursts, the fast neutron population is sampled. During the interval between bursts the epithermal neutron population is sampled along with background gamma radiation due to lingering thermal neutrons. The fast and epithermal neutron population measurements are combined to provide a measurement of formation porosity

Application of imaging plate neutron detector to neutron radiography

CERN Document Server

Fujine, S; Kamata, M; Etoh, M

1999-01-01

As an imaging plate neutron detector (IP-ND) has been available for thermal neutron radiography (TNR) which has high resolution, high sensitivity and wide range, some basic characteristics of the IP-ND system were measured at the E-2 facility of the KUR. After basic performances of the IP were studied, images with high quality were obtained at a neutron fluence of 2 to 7x10 sup 8 n cm sup - sup 2. It was found that the IP-ND system with Gd sub 2 O sub 3 as a neutron converter material has a higher sensitivity to gamma-ray than that of a conventional film method. As a successful example, clear radiographs of the flat view for the fuel side plates with boron burnable poison were obtained. An application of the IP-ND system to neutron radiography (NR) is presented in this paper.

METHODS OF ASSESSMENT OF THE RELATIVE BIOLOGICAL EFFECTIVENESS OF NEUTRONS IN NEUTRON THERAPY

Directory of Open Access Journals (Sweden)

V. A. Lisin

2017-01-01

Full Text Available The relative biological effectiveness (RBE of fast neutrons is an important factor influencing the quality of neutron therapy therefore, the assessment of RBE is of great importance. Experimental and clinical studies as well as different mathematical and radiobiological models are used for assessing RBE. Research is conducted for neutron sources differing in the method of producing particles, energy and energy spectrum. Purpose: to find and analyze the dose-dependence of fast neutron RBE in neutron therapy using the U-120 cyclotron and NG-12I generator. Material and methods: The optimal method for assessing the relative biological effectiveness of neutrons for neutron therapy was described. To analyze the dependence of the RBE on neutron dose, the multi-target model of cell survival was applied. Results: The dependence of the RBE of neutrons produced from the U-120 cyclotron and NG-120 generator on the dose level was found for a single irradiation of biological objects. It was shown that the function of neutron dose was consistent with similar dependencies found by other authors in the experimental and clinical studies.

The “neutron channel design”—A method for gaining the desired neutrons

Directory of Open Access Journals (Sweden)

G. Hu

2016-12-01

Full Text Available The neutrons with desired parameters can be obtained after initial neutrons penetrating various structure and component of the material. A novel method, the “neutron channel design”, is proposed in this investigation for gaining the desired neutrons. It is established by employing genetic algorithm (GA combining with Monte Carlo software. This method is verified by obtaining 0.01eV to 1.0eV neutrons from the Compact Accelerator-driven Neutron Source (CANS. One layer polyethylene (PE moderator was designed and installed behind the beryllium target in CANS. The simulations and the experiment for detection the neutrons were carried out. The neutron spectrum at 500cm from the PE moderator was simulated by MCNP and PHITS software. The counts of 0.01eV to 1.0eV neutrons were simulated by MCNP and detected by the thermal neutron detector in the experiment. These data were compared and analyzed. Then this method is researched on designing the complex structure of PE and the composite material consisting of PE, lead and zirconium dioxide.

Applications of image plates in neutron radiography and neutron diffraction at BARC, Trombay

International Nuclear Information System (INIS)

Shaikh, A.M.

2013-01-01

Neutron radiography techniques based on Gd, Dy and In metallic foils and X-ray film have been used at this centre since early seventies for various NDT and R and D work in nuclear, defence and aerospace industries. In recent years use of photostimulated luminescence based phosphor imaging plate has been introduced in our work. This has enabled to achieve higher sensitivities and dynamic ranges of recording radiographs with acceptable spatial resolution. It also provides digital image information which is more convenient for quantitative evaluations. Neutron image plates have been used in variety of radiography techniques such as conventional neutron radiography (NR), neutron induced beta radiography (NIBR), hydrogen sensitive epithermal neutron radiography (HYSEN) and for neutron powder diffractometry using Apsara, CIRUS and Dhruva reactors as neutron sources. Recently the image plates have also been used for characterization of thermalized neutron beam from a plasma focus neutron source and recording neutron radiographs. Prior to the utilization image plates have been characterised for their performance. Details of the measurements and applications will be presented. (author)

Neutrons in biology

International Nuclear Information System (INIS)

Funahashi, Satoru; Niimura, Nobuo.

1993-01-01

The start of JRR-3M in 1990 was a great epoch to the neutron scattering research in Japan. Abundant neutron beam generated by the JRR-3M made it possible to widen the research field of neutron scattering in Japan. In the early days of neutron scattering, biological materials were too difficult object to be studied by neutrons not only because of their complexity but also because of the strong incoherent scattering by hydrogen. However, the remarkable development of the recent neutron scattering and its related sciences, as well as the availability of higher flux, has made the biological materials one of the most attractive subjects to be studied by neutrons. In early September 1992, an intensive workshop titled 'Neutrons in Biology' was held in Hitachi City by making use of the opportunity of the 4th International Conference on Biophysics and Synchrotron Radiation (BSR92) held in Tsukuba. The workshop was organized by volunteers who are eager to develop the researches in this field in Japan. Numbers of outstanding neutron scattering biologists from U.S., Europe and Asian countries met together and enthusiastic discussions were held all day long. The editors believe that the presentations at the workshop were so invaluable that it is absolutely adequate to put them on record as an issue of JAERI-M and to make them available for scientists to refer to in order to further promote the research in the future. (author)

Study on neutron beam probe. Study on the focused neutron beam

Energy Technology Data Exchange (ETDEWEB)

Kotajima, Kyuya; Suzuki, K.; Fujisawa, M.; Takahashi, T.; Sakamoto, I. [Tohoku Univ., Sendai (Japan). Faculty of Engineering; Wakabayashi, T.

1998-03-01

A monoenergetic focused neutron beam has been produced by utilizing the endoenergetic heavy ion reactions on hydrogen. To realize this, the projectile heavy ion energy should be taken slightly above the threshold energy, so that the excess energy converted to the neutron energy should be very small. In order to improve the capability of the focused neutron beam, some hydrogen stored metal targets have also been tested. Separating the secondary heavy ions (associated particles) from the primary ions (accelerated particles) by using a dipole magnet, a rf separator, and a particle identification system, we could directly count the produced neutrons. This will leads us to the possibility of realizing the standard neutron field which had been the empty dream of many neutron-related researchers in the world. (author)

Neutron flux monitor

International Nuclear Information System (INIS)

Oda, Naotaka.

1993-01-01

The device of the present invention greatly saves an analog processing section such as an analog filter and an analog processing circuit. That is, the device of the present invention comprises (1) a neutron flux detection means for detecting neutron fluxed in the reactor, (2) a digital filter means for dividing signals corresponding to the detected neutron fluxes into predetermined frequency band regions, (3) a calculation processing means for applying a calculation processing corresponding to the frequency band regions to the neutron flux detection signals divided by the digital filter means. With such a constitution, since the neutron detection signals are processed by the digital filter means, the accuracy is improved and the change for the property of the filter is facilitated. Further, when a neutron flux level is obtained, a calculation processing corresponding to the frequency band region can be conducted without the analog processing circuit. Accordingly, maintenance and accuracy are improved by greatly decreasing the number of parts. Further, since problems inherent to the analog circuit are solved, neutron fluxes are monitored at high reliability. (I.S.)

A long neutron optical horn for the ILL neutron-antineutron oscillation experiment

International Nuclear Information System (INIS)

Bitter, T.; Eisert, F.; El-Muzeini, P.; Kessler, M.; Klemt, E.; Lippert, W.; Meienburg, W.; Dubbers, D.

1992-01-01

In the neutron-antineutron oscillation experiment at ILL the divergence of the free flying cold neutron beam was strongly reduced without loss of intensity by the use of a 34 m long neutron-optical horn system. The divergence reduction was accurately studied in order to maintain the total width of the neutron beam below 1.1 m after a neutron free flight distance of about 80 m. The fabrication and performance of this system are described. (orig.)

Activation neutron detector

International Nuclear Information System (INIS)

Ambardanishvili, T.S.; Kolomiitsev, M.A.; Zakharina, T.Y.; Dundua, V.J.; Chikhladze, N.V.

1976-01-01

An activation neutron detector made as a moulded and cured composition of a material capable of being neutron-activated is described. The material is selected from a group consisting of at least two chemical elements, a compound of at least two chemical elements and their mixture, each of the chemical elements and their mixture, each of the chemical elements being capable of interacting with neutrons to form radioactive isotopes having different radiation energies when disintegrating. The material capable of being neutron-activated is distributed throughout the volume of a polycondensation resin inert with respect to neutrons and capable of curing. 17 Claims, No Drawings

Neutron fluence measurement in nuclear facilities.; Medicion de flujos de neutrones en instalaciones nucleares.

Energy Technology Data Exchange (ETDEWEB)

Camacho L, M E

1997-12-01

The objective of present work is to determine the fluence of neutrons in nuclear facilities using two neutron detectors designed and built at Instituto Nacional de Investigaciones Nucleares (ININ), Mexico. The two neutron detectors are of the passive type, based on solid state nuclear tracks detectors (SSNTD). One of the two neutron detectors was used to determine the fluence distribution of the ports at the nuclear research reactor TRIGA Mark III, which belongs to ININ. In these facilities is important to know the neutron fluence distribution characteristic to carried out diverse kind of research activities. The second neutron detector was employed in order to carry out environmental neutron surveillance. The detector has the property to separate the thermal, intermediate and fast components of the neutron fluence. This detector was used to measure the neutron fluence at hundred points around the primary container of the first Mexican Nuclear Power plant `Laguna Verde`. This last detector was also used to determine the neutron fluence in some points of interest, around and inside a low scattering neutron room at the `Centro de Metrologia de Radiaciones Ionizantes` of the ININ, to know the background neutron field produced by the neutron sources used there. The design of the two neutron detector and the results obtained for each of the surveying facilities, are described in this work. (Author).

Methods of neutron spectrometry

International Nuclear Information System (INIS)

Doerschel, B.

1981-01-01

The different methods of neutron spectrometry are based on the direct measurement of neutron velocity or on the use of suitable energy-dependent interaction processes. In the latter case the measuring effect of a detector is connected with the searched neutron spectrum by an integral equation. The solution needs suitable unfolding procedures. The most important methods of neutron spectrometry are the time-of-flight method, the crystal spectrometry, the neutron spectrometry by use of elastic collisions with hydrogen nuclei, and neutron spectrometry with the aid of nuclear reactions, especially of the neutron-induced activation. The advantages and disadvantages of these methods are contrasted considering the resolution, the measurable energy range, the sensitivity, and the experimental and computational efforts. (author)

Extraction of neutron-neutron scattering length from nn coincidence-geometry nd breakup data

Directory of Open Access Journals (Sweden)

E. S. Konobeevski

2011-03-01

Full Text Available We report preliminary results of a kinematically complete experiment on measurement of nd breakup reaction yield at neutron beam RADEX of Institute for Nuclear Research (Moscow, Russia. In the experiment two secondary neutrons are detected in geometry of neutron-neutron final-state interaction. Data are obtained at energy of incident neutrons En = 40 - 60 MeV for various divergence angles of two neutrons ΔΘ = 4, 6, 8º. 1S0 neutron-neutron scattering length ann were determined by comparison of the experimental dependence of reaction yield on the relative energy of two secondary neutrons with results of simulation depending on ann. For En = 40 MeV and ΔΘ = 6º (the highest statistics in the experiment the value ann = -17.9 ± 1.0 fm is obtained. The further improving of accuracy of the experiment and more rigorous theoretical analysis will allow one to remove the existing difference in ann values obtained in different experiments.

Subcritical Neutron Multiplication Measurements of HEU Using Delayed Neutrons as the Driving Source

International Nuclear Information System (INIS)

Hollas, C.L.; Goulding, C.A.; Myers, W.L.

1999-01-01

A new method for the determination of the multiplication of highly enriched uranium systems is presented. The method uses delayed neutrons to drive the HEU system. These delayed neutrons are from fission events induced by a pulsed 14-MeV neutron source. Between pulses, neutrons are detected within a medium efficiency neutron detector using 3 He ionization tubes within polyethylene enclosures. The neutron detection times are recorded relative to the initiation of the 14-MeV neutron pulse, and subsequently analyzed with the Feynman reduced variance method to extract singles, doubles and triples neutron counting rates. Measurements have been made on a set of nested hollow spheres of 93% enriched uranium, with mass values from 3.86 kg to 21.48 kg. The singles, doubles and triples counting rates for each uranium system are compared to calculations from point kinetics models of neutron multiplicity to assign multiplication values. These multiplication values are compared to those from MC NP K-Code calculations

A neutron activation detector

International Nuclear Information System (INIS)

Ambardanishvili, T.S.; Kolomiitsev, M.A.; Zakharina, T.Y.; Dundua, V.J.; Chikhladze, N.V.

1973-01-01

The present invention concerns a neutron activation detector made from a moulded and hardened composition. According to the invention, that composition contains an activable substance constituted by at least two chemical elements and/or compounds of at least two chemical elements. Each of these chemical elements is capable of reacting with the neutrons forming radio-active isotopes with vatious levels of energy during desintegration. This neutron detector is mainly suitable for measuring integral thermal neutron and fast neutron fluxes during irradiation of the sample, and also for measuring the intensities of neutron fields [fr

Layered semiconductor neutron detectors

Science.gov (United States)

Mao, Samuel S; Perry, Dale L

2013-12-10

Room temperature operating solid state hand held neutron detectors integrate one or more relatively thin layers of a high neutron interaction cross-section element or materials with semiconductor detectors. The high neutron interaction cross-section element (e.g., Gd, B or Li) or materials comprising at least one high neutron interaction cross-section element can be in the form of unstructured layers or micro- or nano-structured arrays. Such architecture provides high efficiency neutron detector devices by capturing substantially more carriers produced from high energy .alpha.-particles or .gamma.-photons generated by neutron interaction.

Neutron Scattering Software

Science.gov (United States)

Home Page | Facilities | Reference | Software | Conferences | Announcements | Mailing Lists Neutron Scattering Banner Neutron Scattering Software A new portal for neutron scattering has just been established sets KUPLOT: data plotting and fitting software ILL/TAS: Matlab probrams for analyzing triple axis data

A Wide Spectrum Neutron Polarizer for a Pulsed Neutron Source

International Nuclear Information System (INIS)

Nikitenko, Yu.V.

1994-01-01

A wide spectrum neutron polarizer for a pulsed neutron source is considered. The polarizer is made in a form of a set of magnetized mirrors placed on a drum. Homogeneous rotation of the polarizer is synchronized with the power pulses of the neutron source. The polarizer may be utilized in a collimated neutron beam with cross section of the order of magnitude of 100 cm 2 within a wavelength from 2 up to 20 A on sources with a pulse repetition frequency up to 50 Hz. (author). 5 refs.; 3 figs

Neutron activation system for spectral measurements of pulsed ion diode neutron production

International Nuclear Information System (INIS)

Hanson, D.L.; Kruse, L.W.

1980-02-01

A neutron energy spectrometer has been developed to study intense ion beam-target interactions in the harsh radiation environment of a relativistic electron beam source. The main component is a neutron threshold activation system employing two multiplexed high efficiency Ge(Li) detectors, an annihilation gamma coincidence system, and a pneumatic sample transport. Additional constraints on the neutron spectrum are provided by total neutron yield and time-of-flight measurements. A practical lower limit on the total neutron yield into 4π required for a spectral measurement with this system is approx. 10 10 n where the neutron yield is predominantly below 4 MeV and approx. 10 8 n when a significant fraction of the yield is above 4 MeV. Applications of this system to pulsed ion diode neutron production experiments on Hermes II are described

Neutron spectra characteristics for the intense neutron source, INS

International Nuclear Information System (INIS)

Battat, M.; Dierckx, R.; Emigh, C.R.

1977-01-01

The Intense Neutron Source, INS, facility is presently under construction at the Los Alamos Scientific Laboratory. Its purpose is to provide a broad base for research work related to the radiation effects produced by 14-MeV neutrons from a D-T burn of a fusion reactor. The INS facility produces a D-T burn-like reaction from the collision of an intense tritium-ion beam with a supersonic jet target of deuterium gas. The reaction produces a typical D-T 14-MeV neutron spectrum. By adding a fission blanket surrounding the D-T ''burn,'' the neutron spectral shape may be tailored to match almost perfectly the anticipated first-wall spectra from presently proposed fusion reactors. With a blanket in place, the total production of neutrons can be as large as 3 x 10 16 n/s and experimental volumes of the order of 1000 cm 3 can be available at flux levels greater than 0.6 x 10 14 n/cm 2 s

Basics of Neutrons for First Responders

Energy Technology Data Exchange (ETDEWEB)

Rees, Brian G. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2018-02-05

These are slides from a presentation on the basics of neutrons. A few topics covered are: common origins of terrestrial neutron radiation, neutron sources, neutron energy, interactions, detecting neutrons, gammas from neutron interactions, neutron signatures in gamma-ray spectra, neutrons and NaI, neutron fluence to dose (msV), instruments' response to neutrons.

Real time neutron flux monitoring using Rh self powered neutron detector

Energy Technology Data Exchange (ETDEWEB)

Juna, Byung Jin; Lee, Byung Chul; Park, Sang Jun; Jung, Hoan Sung [KAERI, Daejeon (Korea, Republic of)

2012-10-15

Rhodium (Rh) self powered neutron detectors (SPNDs) are widely used for on line monitoring of local neutron flux. Its signal is slower than the actual variation of neutron flux owing to a delayed {beta} decay of the Rh activation product, but real time monitoring is possible by solving equations between the neutron reaction rate in the detector and its signal. While the measuring system is highly reliable, the accuracy depends on the method solving the equations and accuracy of the parameters in the equations. The uncertain parameters are the contribution of gamma rays to the signal, and the branching ratios of Rh 104 and Rh 104m after the neutron absorption of Rh 103. Real time neutron flux monitoring using Rh SPNDs has been quite successful for neutron transmutation doping (NTD) at HANARO. We revisited the initial data used for the verification of a real time monitoring system, to refine algorithm for a better solution and to check the parameters for correctness. As a result, we suggest an effective way to determine the prompt parameter.

Real time neutron flux monitoring using Rh self powered neutron detector

International Nuclear Information System (INIS)

Juna, Byung Jin; Lee, Byung Chul; Park, Sang Jun; Jung, Hoan Sung

2012-01-01

Rhodium (Rh) self powered neutron detectors (SPNDs) are widely used for on line monitoring of local neutron flux. Its signal is slower than the actual variation of neutron flux owing to a delayed β decay of the Rh activation product, but real time monitoring is possible by solving equations between the neutron reaction rate in the detector and its signal. While the measuring system is highly reliable, the accuracy depends on the method solving the equations and accuracy of the parameters in the equations. The uncertain parameters are the contribution of gamma rays to the signal, and the branching ratios of Rh 104 and Rh 104m after the neutron absorption of Rh 103. Real time neutron flux monitoring using Rh SPNDs has been quite successful for neutron transmutation doping (NTD) at HANARO. We revisited the initial data used for the verification of a real time monitoring system, to refine algorithm for a better solution and to check the parameters for correctness. As a result, we suggest an effective way to determine the prompt parameter

Neutron therapy

International Nuclear Information System (INIS)

Riesler, Rudi

1995-01-01

Standard radiotherapy uses Xrays or electrons which have low LET (linear energy transfer); in contrast, particles such as neutrons with high LET have different radiobiological responses. In the late 1960s, clinical trials by Mary Catterall at the Hammersmith Hospital in London indicated that fast neutron radiation had clinical advantages for certain malignant tumours. Following these early clinical trials, several cyclotron facilities were built in the 1980s for fast neutron therapy, for example at the University of Washington, Seattle, and at UCLA. Most of these newer machines use extracted cyclotron proton beams in the range 42 to 66 MeV with beam intensities of 15 to 60 microamps. The proton beams are transported to dedicated therapy rooms, where neutrons are produced from beryllium targets. Second-generation clinical trials showed that accurate neutron beam delivery to the tumour site is more critical than for photon therapy. In order to achieve precise beam geometries, the extracted proton beams have to be transported through a gantry which can rotate around the patient and deliver beams from any angle; also the neutron beam outline (''field shape'') must be adjusted to extremely irregular shapes using a flexible collimation system. A therapy procedure has to be appropriately organized, with physicians, radiotherapists, nurses, medical physicists and other staff in attendance; other specialized equipment, such as CT or MRI scanners and radiation simulators must be made available. Neutron therapy is usually performed only in radiation oncology departments of major medical centres

Polarimetric neutron scattering

International Nuclear Information System (INIS)

Tasset, F.

2001-01-01

Polarimetric Neutron Scattering in introduced, both by, explaining methodological issues and the corresponding instrumental developments. After a short overview of neutron spin polarization and the neutron polarization 3d-vector a pictorial approach of the microscopic theory is used to show how a polarized beam interacts with lattice and magnetic Fourier components in a crystal. Examples are given of using Spherical Neutron Polarimetry (SNP) and the corresponding Cryopad polarimeter for the investigation of non-collinear magnetic structures. (R.P.)

Neutron kinetics in moderators and SNM detection through epithermal-neutron-induced fissions

Energy Technology Data Exchange (ETDEWEB)

Gozani, Tsahi, E-mail: tgmaven@gmail.com [1050 Harriet St., Palo Alto, CA 94301 (United States); King, Michael J. [Rapiscan Laboratories Inc., 520 Almanor Ave., Sunnyvale, CA 94085 (United States)

2016-01-01

Extension of the well-established Differential Die Away Analysis (DDAA) into a faster time domain, where more penetrating epithermal neutrons induce fissions, is proposed and demonstrated via simulations and experiments. In the proposed method the fissions stimulated by thermal, epithermal and even higher-energy neutrons are measured after injection of a narrow pulse of high-energy 14 MeV (d,T) or 2.5 MeV (d,D) source neutrons, appropriately moderated. The ability to measure these fissions stems from the inherent correlation of neutron energy and time (“E–T” correlation) during the process of slowing down of high-energy source neutrons in common moderating materials such as hydrogenous compounds (e.g., polyethylene), heavy water, beryllium and graphite. The kinetic behavior following injection of a delta-function-shaped pulse (in time) of 14 MeV neutrons into such moderators is studied employing MCNPX simulations and, when applicable, some simple “one-group” models. These calculations served as a guide for the design of a source moderator which was used in experiments. Qualitative relationships between slowing-down time after the pulse and the prevailing neutron energy are discussed. A laboratory system consisting of a 14 MeV neutron generator, a polyethylene-reflected Be moderator, a liquid scintillator with pulse-shape discrimination (PSD) and a two-parameter E–T data acquisition system was set up to measure prompt neutron and delayed gamma-ray fission signatures in a 19.5% enriched LEU sample. The measured time behavior of thermal and epithermal neutron fission signals agreed well with the detailed simulations. The laboratory system can readily be redesigned and deployed as a mobile inspection system for SNM in, e.g., cars and vans. A strong pulsed neutron generator with narrow pulse (<75 ns) at a reasonably high pulse frequency could make the high-energy neutron induced fission modality a realizable SNM detection technique.

Generation of neutron standing waves at total reflection of polarized neutrons

International Nuclear Information System (INIS)

Aksenov, V.L.; Nikitenko, Yu.V.; Kozhevnikov, S.V.; Radu, F.; Kruijs, R.; Rekveldt, M.Th.

1999-01-01

The regime of neutron standing waves at reflection of polarized thermal neutrons from the structure glass/Cu (1000 A Angstrom)/Ti (2000 A Angstrom)/Co (60 A Angstrom)/Ti (300 A Angstrom) in a magnetic field directed at an angle to the sample plane is realized. The intensity of neutrons with a particular spin projection on the external magnetic field direction appears to be a periodic function of the neutron wavelength and the glancing angle of the reflected beam. It is shown that the neutron standing wave regime can be a very sensitive method for the determination of changes in the spatial position of magnetic noncollinear layers. (author)

A neutron calibration technique for detectors with low neutron/high photon sensitivity

International Nuclear Information System (INIS)

Jahr, R.; Guldbakke, S.; Cosack, M.; Dietze, G.; Klein, H.

1978-03-01

The neutron response of a detector with low neutron-/high photon sensitivity is given by the difference of two terms: the response to the mixed neutron-photon field, measured directly, and the response to the photons, deduced from additional measurements with a photon spectrometer. The technique is particularly suited for use in connection with targets which consist of a thick backing and thin layer of neutron producing material such as T, D, Li nuclei. Then the photon component of the mixed field is very nearly the same as the pure photon field from a 'phantom target', being identical with the neutron producing target except for the missing neutron producing material. Using this technique in connection with a T target (Ti-T-layer on silver backing) and the corresponding phantom target (Ti-layer on silver backing), a GM counter was calibrated at a neutron energy of 2.5 MeV. Possibilities are discussed to subsequently calibrate the GM counter at other neutron energies without the use of the photon spectrometer. (orig./HP) [de

Neutron protection material and neutron protection devices made of such material

International Nuclear Information System (INIS)

Ries, W.

1984-01-01

This is concerned with a neutron protection material made of thermoplastic or thermosetting plastic from high molecule hydrocarbon compounds with particularly high hydrogen and carbon contents as braking or shielding material (moderator) for fast neutrons. The plastic can contain boron for absorbing low energy neutrons. The material is used to manufacture foil, plates, pipes, shielding walls, components, bodies for radiation protection equipment, devices and plant and for neutron protection clothes. (orig./HP) [de

Neutron radiography of thick hydrogenous materials with use of an imaging plate neutron detector

International Nuclear Information System (INIS)

Kato, K.; Matsumoto, G.; Karasawa, Y.; Niimura, N.; Matsubayashi, M.; Tsuruno, A.

1996-01-01

The value of the neutron mass attenuation coefficient of hydrogen being very high, it is extremely difficult to image normal size, living animals with neutron radiography. However, the authors suggest the possibility of applying neutron radiography for biomedical specimens. The organs in the breast, bones and cartilages in the extremities, and the tail of mice and rats were clearly imaged by neutron radiography with Gd foils as neutron converters and X-ray films. However, no contours of the organs in the mouse abdomen were visible with neutron radiography with an exposure time of 200 s. By adding Gd or Li compounds as neutron converters to imaging X-ray plates, imaging plates have been developed for neutron detectors. A trial using these imaging plates for neutron radiography of water-filled containers and the abdomen of mice was completed. The roundness of a 100 ml-beaker was imaged with a neutron exposure of 180 s. Obscure contours of the liver and kidneys of the mouse were imaged with a neutron exposure of 100 s. (orig.)

Pulsed thermal neutron source at the fast neutron generator.

Science.gov (United States)

Tracz, Grzegorz; Drozdowicz, Krzysztof; Gabańska, Barbara; Krynicka, Ewa

2009-06-01

A small pulsed thermal neutron source has been designed based on results of the MCNP simulations of the thermalization of 14 MeV neutrons in a cluster-moderator which consists of small moderating cells decoupled by an absorber. Optimum dimensions of the single cell and of the whole cluster have been selected, considering the thermal neutron intensity and the short decay time of the thermal neutron flux. The source has been built and the test experiments have been performed. To ensure the response is not due to the choice of target for the experiments, calculations have been done to demonstrate the response is valid regardless of the thermalization properties of the target.

Solving 1D plasmas and 2D boundary problems using Jack polynomials and functional relations

International Nuclear Information System (INIS)

Fendley, P.; Saleur, H.; Lesage, F.

1995-01-01

The general one-dimensional open-quotes log-sineclose quotes gas is defined by restricting the positive and negative charges of a two-dimensional Coulomb gas to live on a circle. Depending on charge constraints, this problem is equivalent to different boundary field theories. We study the electrically neutral case, which is equivalent to a two-dimensional free boson with an impurity cosine potential. We use two different methods: a perturbative one based on Jack symmetric functions, and a non-perturbative one based on the thermodynamic Bethe ansatz and functional relations. The first method allows us to find an explicit series expression for all coefficients in the virial expansion of the free energy and the experimentally measurable conductance. Some results for correlation functions are also presented. The second method gives an expression for the full free energy, which yields a surprising fluctuation-dissipation relation between the conductance and the free energy

Utilization of low voltage D-T neutron generators in neutron physics studies

Energy Technology Data Exchange (ETDEWEB)

Singkarat, S.

1995-08-01

In a small nuclear laboratory of a developing country a low voltage D-T neutron generator can be a very useful scientific apparatus. Such machines have been used successfully for more than 40 years in teaching and scientific research. The original continuous mode 150-kV D-T neutron generator has been modified to have also a capability of producing 2-ns pulsed neutrons. Together with a carefully designed 10 m long flight path collimator and shielding of a 25 cm diameter {center_dot} 10 cm thick BC-501 neutron detector, the pulsing system was successfully used for measuring the double differential cross-section (DDX) of natural iron for 14.1-MeV neutron from the angle of 30 deg to 150 deg in 10 deg steps. In order to extend the utility of the generator, two methods for converting the almost monoenergetic 14-MeV neutrons to monoenergetic neutrons of lower energy were proposed and tested. The first method uses a pulsed neutron generator and the second method uses an ordinary continuous mode generator. The latter method was successfully used to measure the scintillation light output of a 1.4 cm diameter spherical NE-213 scintillation detector. The neutron generator has also been used in the continuous search for improved neutron detection techniques. There is a proposal, based on Monte Carlo calculations, of using a scintillation fiber for a fast neutron spectrometer. Due to the slender shape of the fiber, the pattern of produced light gives a peak in the pulse height spectrum instead of the well-known rectangular-like distribution, when the fiber is bombarded end-on by a beam of 14-MeV neutrons. Experimental investigations were undertaken. Detailed investigations on the light transportation property of a short fiber were performed. The predicted peak has not yet been found but the fiber detector may be developed as a directional discrimination fast neutron detector. 18 refs.

Fusion neutron detector calibration using a table-top laser generated plasma neutron source

International Nuclear Information System (INIS)

Hartke, R.; Symes, D.R.; Buersgens, F.; Ruggles, L.E.; Porter, J.L.; Ditmire, T.

2005-01-01

Using a high intensity, femtosecond laser driven neutron source, a high-sensitivity neutron detector was calibrated. This detector is designed for observing fusion neutrons at the Z accelerator in Sandia National Laboratories. Nuclear fusion from laser driven deuterium cluster explosions was used to generate a clean source of nearly monoenergetic 2.45 MeV neutrons at a well-defined time. This source can run at 10 Hz and was used to build up a clean pulse-height spectrum on scintillating neutron detectors giving a very accurate calibration for neutron yields at 2.45 MeV

Neutron image intensifier tubes

International Nuclear Information System (INIS)

Verat, M.; Rougeot, H.; Driard, B.

1983-01-01

The most frequently used techniques in neutron radiography employ a neutron converter consisting of either a scintillator or a thin metal sheet. The radiation created by the neutrons exposes a photographic film that is in contact with the converter: in the direct method, the film is exposed during the time that the object is irradiated with neutrons; in the transfer method, the film is exposed after the irradiation of the object with neutrons. In industrial non-destructive testing, when many identical objects have to be checked, these techniques have several disadvantages. Non-destructive testing systems without these disadvantages can be constructed around neutron-image intensifier tubes. A description and the operating characteristics of neutron-image intensifier tubes are given. (Auth.)

Neutron multiplicity measurements with ³He alternative: Straw neutron detectors

Energy Technology Data Exchange (ETDEWEB)

Mukhopadhyay, Sanjoy [Arnold Avenue Andrews AFB, Joint Base Andrews, MD (United States); Wolff, Ronald [Arnold Avenue Andrews AFB, Joint Base Andrews, MD (United States); Detwiler, Ryan [Arnold Avenue Andrews AFB, Joint Base Andrews, MD (United States); Maurer, Richard [Arnold Avenue Andrews AFB, Joint Base Andrews, MD (United States); Mitchell, Stephen [National Security Technologies, LLC, Las Vegas, NV (United States); Guss, Paul [Remote Sensing Lab. - Nellis, Las Vegas, NV (United States); Lacy, Jeffrey L. [Proportional Technologies, Inc., Houston, TX (United States); Sun, Liang [Proportional Technologies, Inc., Houston, TX (United States); Athanasiades, Athanasios [Proportional Technologies, Inc., Houston, TX (United States)

2015-01-27

Counting neutrons emitted by special nuclear material (SNM) and differentiating them from the background neutrons of various origins is the most effective passive means of detecting SNM. Unfortunately, neutron detection, counting, and partitioning in a maritime environment are complex due to the presence of high-multiplicity spallation neutrons (commonly known as ‘‘ship effect ’’) and to the complicated nature of the neutron scattering in that environment. A prototype neutron detector was built using ¹⁰B as the converter in a special form factor called ‘‘straws’’ that would address the above problems by looking into the details of multiplicity distributions of neutrons originating from a fissioning source. This paper describes the straw neutron multiplicity counter (NMC) and assesses the performance with those of a commercially available fission meter. The prototype straw neutron detector provides a large-area, efficient, lightweight, more granular (than fission meter) neutron-responsive detection surface (to facilitate imaging) to enhance the ease of application of fission meters. Presented here are the results of preliminary investigations, modeling, and engineering considerations leading to the construction of this prototype. This design is capable of multiplicity and Feynman variance measurements. This prototype may lead to a near-term solution to the crisis that has arisen from the global scarcity of ³He by offering a viable alternative to fission meters. This paper describes the work performed during a 2-year site-directed research and development (SDRD) project that incorporated straw detectors for neutron multiplicity counting. The NMC is a two-panel detector system. We used ¹⁰B (in the form of enriched boron carbide: ¹⁰B₄C) for neutron detection instead of ³He. In the first year, the project worked with a panel of straw neutron detectors, investigated its characteristics, and

Neutron dosimeters and survey meters in accelerators, reactors and other neutron environments

International Nuclear Information System (INIS)

1989-03-01

Neutron fields in occupationally accessible areas around nuclear reactors, radioisotope sources and medical and high energy accelerators have been characterized using currently available information. Neutron, rem meters, such as the Leake detector, are the most suitable instruments available for conducting neutron dose rate surveys in the vicinity of radioisotope neutron sources, nuclear reactors and medical accelerators. However, these instruments have been shown to be deficient in that they overrespond by a factor of four to neutrons in the 0.1 to 1 MeV range and are insensitive to neutrons from about 1 eV up to about 10 keV. Also, they are insensitive to neutrons above 20 MeV and their use must be restricted near high energy accelerators where significant numbers of neutrons above 20 MeV are known to be present. The most suitable instrument of measure dose from neutrons above 20 MeV is the 12 C(n,2n) 11 C scintillation chamber. Commercially available rem meters frequently use BF 3 counters in the pulse mode to detect thermal neutrons. Therefore, measurements around pulsed accelerators must be made with caution to ensure that the detector is not saturated during each pulse and that the accelerator pulse period is greater than the response time of the detector. The personal neutron dosimeters currently available either are known to be insensitive to neutrons above 20 MeV or have not been tested. Also, all except the albedo dosimeter are insensitive to or have not been tested for neutron energies in the range 1 eV to 10 keV. Several dosimeter types respond reasonably well to neutrons in the energy range 0.1 to 15 MeV, for example, CR-39, bubble and superheated drop detectors. However, the first gas a lower limit of sensitivity of about 0.3 mSv. The bubble detector can be designed to measure doses as small as 1μSv and offers the additional benefit of direct-reading capability. The superheated drop detector is not suitable for use around pulsed accelerators because

Neutron resonance spectroscopy

International Nuclear Information System (INIS)

Gunsing, F.

2005-06-01

The present document has been written in order to obtain the diploma 'Habilitation a Diriger des Recherches'. Since this diploma is indispensable to supervise thesis students, I had the intention to write a document that can be useful for someone starting in the field of neutron resonance spectroscopy. Although the here described topics are already described elsewhere, and often in more detail, it seemed useful to have most of the relevant information in a single document. A general introduction places the topic of neutron-nucleus interaction in a nuclear physics context. The large variations of several orders of magnitude in neutron-induced reaction cross sections are explained in terms of nuclear level excitations. The random character of the resonances make nuclear model calculation predictions impossible. Then several fields in physics where neutron-induced reactions are important and to which I have contributed in some way or another, are mentioned in a first synthetic chapter. They concern topics like parity nonconservation in certain neutron resonances, stellar nucleosynthesis by neutron capture, and data for nuclear energy applications. The latter item is especially important for the transmutation of nuclear waste and for alternative fuel cycles. Nuclear data libraries are also briefly mentioned. A second chapter details the R-matrix theory. This formalism is the foundation of the description of the neutron-nucleus interaction and is present in all fields of neutron resonance spectroscopy. (author)

Neutron dosimetry - A review

Energy Technology Data Exchange (ETDEWEB)

Baum, J W

1955-03-29

This review summarizes information on the following subjects: (1) physical processes of importance in neutron dosimetry; (2) biological effects of neutrons; (3) neutron sources; and (4) instruments and methods used in neutron dosimetry. Also, possible improvements in dosimetry instrumentation are outlined and discussed. (author)

Response of six neutron survey meters in mixed fields of fast and thermal neutrons.

Science.gov (United States)

Kim, S I; Kim, B H; Chang, I; Lee, J I; Kim, J L; Pradhan, A S

2013-10-01

Calibration neutron fields have been developed at KAERI (Korea Atomic Energy Research Institute) to study the responses of commonly used neutron survey meters in the presence of fast neutrons of energy around 10 MeV. The neutron fields were produced by using neutrons from the (241)Am-Be sources held in a graphite pile and a DT neutron generator. The spectral details and the ambient dose equivalent rates of the calibration fields were established, and the responses of six neutron survey meters were evaluated. Four single-moderator-based survey meters exhibited an under-responses ranging from ∼9 to 55 %. DINEUTRUN, commonly used in fields around nuclear reactors, exhibited an over-response by a factor of three in the thermal neutron field and an under-response of ∼85 % in the mixed fields. REM-500 (tissue-equivalent proportional counter) exhibited a response close to 1.0 in the fast neutron fields and an under-response of ∼50 % in the thermal neutron field.

Instrumentation with polarized neutrons

International Nuclear Information System (INIS)

Boeni, P.; Muenzer, W.; Ostermann, A.

2009-01-01

Neutron scattering with polarization analysis is an indispensable tool for the investigation of novel materials exhibiting electronic, magnetic, and orbital degrees of freedom. In addition, polarized neutrons are necessary for neutron spin precession techniques that path the way to obtain extremely high resolution in space and time. Last but not least, polarized neutrons are being used for fundamental studies as well as very recently for neutron imaging. Many years ago, neutron beam lines were simply adapted for polarized beam applications by adding polarizing elements leading usually to unacceptable losses in neutron intensity. Recently, an increasing number of beam lines are designed such that an optimum use of polarized neutrons is facilitated. In addition, marked progress has been obtained in the technology of 3 He polarizers and the reflectivity of large-m supermirrors. Therefore, if properly designed, only factors of approximately 2-3 in neutron intensity are lost. It is shown that S-benders provide neutron beams with an almost wavelength independent polarization. Using twin cavities, polarized beams with a homogeneous phase space and P>0.99 can be produced without significantly sacrificing intensity. It is argued that elliptic guides, which are coated with large m polarizing supermirrors, provide the highest flux.

Neutron producing reactions in PuBe neutron sources

Energy Technology Data Exchange (ETDEWEB)

Bagi, János [European Commission, Joint Research Centre (JRC), Institute for Transuranium Elements (ITU) (Germany); Lakosi, László; Nguyen, Cong Tam [Centre for Energy Research, Hungarian Academy of Sciences, Budapest (Hungary)

2016-01-01

There are a plenty of out-of-use plutonium–beryllium neutron sources in Eastern Europe presenting both nuclear safeguards and security issues. Typically, their actual Pu content is not known. In the last couple of years different non-destructive methods were developed for their characterization. For such methods detailed knowledge of the nuclear reactions taking place within the source is necessary. In this paper we investigate the role of the neutron producing reactions, their contribution to the neutron yield and their dependence on the properties of the source.

Neutrons at COSY

International Nuclear Information System (INIS)

Filges, D.; Freiesleben, H.

1988-05-01

For many years neutrons were considered important both as a useful probe in nuclear physics research and as an initiator and catalyst for fission, fusion and other applications. As a result knowledge about neutrons, especially below 20 MeV, received organized world-wide attention. Research with neutrons at medium energies, say 50 MeV to several GeV, has not consistently received attention and no systematic evaluations exist. But there is a large and considerable interest today because medium energy neutrons are very important in basic science and technology. The aim of this workshop was to provide an overview of the present status and the research which should be carried out in this field in future and which kind of experiments should be performed at the COSY facility: State-of-the-art about medium energy neutron experiments and existing facilities; planned experiments; needs for experiments doing research with neutrons at COSY (detectors, accelerator requirements, time structure etc.); what will be a first experiment to measure neutrons at COSY. The interest in this workshop is documented by a large number of participants. Copies of the viewgraphs of the talks are provided. (orig./HP)

Neutronic performance issues for the Spallation Neutron Source moderators

International Nuclear Information System (INIS)

Iverson, E.B.; Murphy, B.D.

2001-01-01

We continue to develop the neutronic models of the Spallation Neutron Source target station and moderators in order to better predict the neutronic performance of the system as a whole and in order to better optimize that performance. While we are not able to say that every model change leads to more intense neutron beams being predicted, we do feel that such changes are advantageous in either performance or in the accuracy of the prediction of performance. We have computationally and experimentally studied the neutronics of hydrogen-water composite moderators such as are proposed for the SNS Project. In performing these studies, we find that the composite moderator, at least in the configuration we have examined, does not provide performance characteristics desirable for the instruments proposed and being designed for this neutron scattering facility. The pulse width as a function of energy is significantly broader than for other moderators, limiting attainable resolution-bandwidth combinations. Furthermore, there is reason to expect that higher-energy (0.1-1 eV) applications will be significantly impacted by bimodal pulse shapes requiring enormous effort to parameterize. As a result of these studies, we have changed the SNS design, and will not use a composite moderator at this time. We have analyzed the depletion of a gadolinium poison plate in a hydrogen moderator at the Spallation Neutron Source, and found that conventional poison thicknesses will be completely unable to last the desired component lifetime of three operational years. A poison plate 300-600 μm thick will survive for the required length of time, but will somewhat degrade the intensity (by as much as 15% depending on neutron energy) and the consistency of the neutron source performance. Our results should scale fairly easily to other moderators on this or any other spallation source. While depletion will be important for all highly-absorbing materials in high-flux regions, we feel it likely that

Isotopic neutron sources for neutron activation analysis

International Nuclear Information System (INIS)

Hoste, J.

1988-06-01

This User's Manual is an attempt to provide for teaching and training purposes, a series of well thought out demonstrative experiments in neutron activation analysis based on the utilization of an isotopic neutron source. In some cases, these ideas can be applied to solve practical analytical problems. 19 refs, figs and tabs

New opportunities in neutron capture research using advanced pulsed neutron sources

International Nuclear Information System (INIS)

Bowman, C.D.

1987-08-01

The extraordinary neutron intensities available from the new spallation pulsed neutron sources open up exciting opportunities for basic and applied research in neutron nuclear physics. Prospective experiments are reviewed with particular attention to those with a strong connection to capture gamma-ray spectroscopy

Use of a neutron guide in industrial neutron radiography

International Nuclear Information System (INIS)

Zaccheo, M.; Berthon, J.; Uzureau, G.; Laporte, A.

1983-01-01

This paper describes the neutron radiography facility associated with the Orphee high flux reactor at the Saclay Nuclear Research Centre. Following a brief background review, the paper deals with: the presentation of the facility, with emphasis on all the mechanical systems involved; description of the control and monitoring console; a non-exhaustive list of the facility's potentialities; the advantages and drawbacks of the use of a neutron guide to carry out industrial neutron radiography. (Auth.)

Neutron Detector Signal Processing to Calculate the Effective Neutron Multiplication Factor of Subcritical Assemblies

International Nuclear Information System (INIS)

Talamo, Alberto; Gohar, Yousry

2016-01-01

This report describes different methodologies to calculate the effective neutron multiplication factor of subcritical assemblies by processing the neutron detector signals using MATLAB scripts. The subcritical assembly can be driven either by a spontaneous fission neutron source (e.g. californium) or by a neutron source generated from the interactions of accelerated particles with target materials. In the latter case, when the particle accelerator operates in a pulsed mode, the signals are typically stored into two files. One file contains the time when neutron reactions occur and the other contains the times when the neutron pulses start. In both files, the time is given by an integer representing the number of time bins since the start of the counting. These signal files are used to construct the neutron count distribution from a single neutron pulse. The built-in functions of MATLAB are used to calculate the effective neutron multiplication factor through the application of the prompt decay fitting or the area method to the neutron count distribution. If the subcritical assembly is driven by a spontaneous fission neutron source, then the effective multiplication factor can be evaluated either using the prompt neutron decay constant obtained from Rossi or Feynman distributions or the Modified Source Multiplication (MSM) method.

Neutron Detector Signal Processing to Calculate the Effective Neutron Multiplication Factor of Subcritical Assemblies

Energy Technology Data Exchange (ETDEWEB)

Talamo, Alberto [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Gohar, Yousry [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division

2016-06-01

This report describes different methodologies to calculate the effective neutron multiplication factor of subcritical assemblies by processing the neutron detector signals using MATLAB scripts. The subcritical assembly can be driven either by a spontaneous fission neutron source (e.g. californium) or by a neutron source generated from the interactions of accelerated particles with target materials. In the latter case, when the particle accelerator operates in a pulsed mode, the signals are typically stored into two files. One file contains the time when neutron reactions occur and the other contains the times when the neutron pulses start. In both files, the time is given by an integer representing the number of time bins since the start of the counting. These signal files are used to construct the neutron count distribution from a single neutron pulse. The built-in functions of MATLAB are used to calculate the effective neutron multiplication factor through the application of the prompt decay fitting or the area method to the neutron count distribution. If the subcritical assembly is driven by a spontaneous fission neutron source, then the effective multiplication factor can be evaluated either using the prompt neutron decay constant obtained from Rossi or Feynman distributions or the Modified Source Multiplication (MSM) method.

New generation non-stationary portable neutron generators for biophysical applications of Neutron Activation Analysis.

Science.gov (United States)

Marchese, N; Cannuli, A; Caccamo, M T; Pace, C

2017-01-01

Neutron sources are increasingly employed in a wide range of research fields. For some specific purposes an alternative to existing large-scale neutron scattering facilities, can be offered by the new generation of portable neutron devices. This review reports an overview for such recently available neutron generators mainly addressed to biophysics applications with specific reference to portable non-stationary neutron generators applied in Neutron Activation Analysis (NAA). The review reports a description of a typical portable neutron generator set-up addressed to biophysics applications. New generation portable neutron devices, for some specific applications, can constitute an alternative to existing large-scale neutron scattering facilities. Deuterium-Deuterium pulsed neutron sources able to generate 2.5MeV neutrons, with a neutron yield of 1.0×10 6 n/s, a pulse rate of 250Hz to 20kHz and a duty factor varying from 5% to 100%, when combined with solid-state photon detectors, show that this kind of compact devices allow rapid and user-friendly elemental analysis. "This article is part of a Special Issue entitled "Science for Life" Guest Editor: Dr. Austen Angell, Dr. Salvatore Magazù and Dr. Federica Migliardo". Copyright © 2016 Elsevier B.V. All rights reserved.

LANSA: A large neutron scintillator array for neutron spectroscopy at Nova

International Nuclear Information System (INIS)

Nelson, M.B.; Cable, M.D.; Bennett, C.K.; Mant, G.

1992-01-01

A very sensitive neutron time-of-flight spectrometer is now in use at Nova. LANSA consists of 960 channels of a neutron sensitive liquid scintillator (10 x lO x lO cm) coupled to a photomultiplier tube followed by a discriminator, TDC and ADC to allow the measurement of neutron arrival time as well as pulse size. LANSA is capable of measuring yields as low as 2.3 x 10 5 DT neutrons (100 detected hits) with resolution of 2.3 ns (170 key for 14 MeV neutrons with 20 m flight path). Shielding and collimation provide background levels low enough to allow measurement of secondary and tertiary reaction neutrons. Details of design, testing, calibration and experimental results will be presented. This work was performed under the auspices of the US Department of Energy by Lawrence Livermore National Laboratory under contract No. W-7405-ENG-48

Neutron guides and scientific neutron equipment at CILAS/GMI

International Nuclear Information System (INIS)

Gautier-Picard, P.

2001-01-01

The French company CILAS is the world's leading supplier of complete neutron guide systems. The neutron optics with multilayer coatings produced by CILAS has become an international standard for neutron beam transportation at modern research institutes. During the last 30 years, CILAS designed, produced and installed more than 5000 meters of guides in many European, American and Asian countries. By these projects the company has acquired a very strong experience with: conception, design, manufacturing, setting up of Neutron Guides. In most cases, CILAS was in charge of the design, as well as the manufacturing of the whole system, comprising optical and mechanical components, vacuum system, shutter and shielding definition. By our long experience we have also acquired good knowledge of the materials used in this specific nuclear environment and their behavior under radiation such as glass, borated or not, coatings, glue or metal. To reinforce its leadership and presence in neutron research, CILAS acquired the company Grenoble Modular Instruments (GMI) a leading company in high precision mechanics, engineering and manufacturing of spectrometers and scientific equipment for neutron and synchrotron research. This merger allows us to design and to supply a complete range of high precision optical and mechanical eqipment for neutron research. CILAS and GMI have designed, manufactured and installed a High Resolution Powder Diffractometer for the 30MW Korean Hanaro Reactor. This project included the calculation, design and supply of the complete biological shielding of the instrument as well as for the primary beam shutter on the thermal beamport. (author)

Neutron-neutron quasifree scattering in nd breakup at 10 MeV

Science.gov (United States)

Malone, R. C.; Crowe, B.; Crowell, A. S.; Cumberbatch, L. C.; Esterline, J. H.; Fallin, B. A.; Friesen, F. Q. L.; Han, Z.; Howell, C. R.; Markoff, D.; Ticehurst, D.; Tornow, W.; Witała, H.

2016-03-01

The neutron-deuteron (nd) breakup reaction provides a rich environment for testing theoretical models of the neutron-neutron (nn) interaction. Current theoretical predictions based on rigorous ab-initio calculations agree well with most experimental data for this system, but there remain a few notable discrepancies. The cross section for nn quasifree (QFS) scattering is one such anomaly. Two recent experiments reported cross sections for this particular nd breakup configuration that exceed theoretical calculations by almost 20% at incident neutron energies of 26 and 25 MeV [1, 2]. The theoretical values can be brought into agreement with these results by increasing the strength of the 1S0 nn potential matrix element by roughly 10%. However, this modification of the nn effective range parameter and/or the 1S0 scattering length causes substantial charge-symmetry breaking in the nucleon-nucleon force and suggests the possibility of a weakly bound di-neutron state [3]. We are conducting new measurements of the cross section for nn QFS in nd breakup. The measurements are performed at incident neutron beam energies below 20 MeV. The neutron beam is produced via the 2H(d, n)3He reaction. The target is a deuterated plastic cylinder. Our measurements utilize time-of-flight techniques with a pulsed neutron beam and detection of the two emitted neutrons in coincidence. A description of our initial measurements at 10 MeV for a single scattering angle will be presented along with preliminary results. Also, plans for measurements at other energies with broad angular coverage will be discussed.

MAGNETIC NEUTRON SCATTERING

Energy Technology Data Exchange (ETDEWEB)

ZALIZNYAK,I.A.; LEE,S.H.

2004-07-30

Much of our understanding of the atomic-scale magnetic structure and the dynamical properties of solids and liquids was gained from neutron-scattering studies. Elastic and inelastic neutron spectroscopy provided physicists with an unprecedented, detailed access to spin structures, magnetic-excitation spectra, soft-modes and critical dynamics at magnetic-phase transitions, which is unrivaled by other experimental techniques. Because the neutron has no electric charge, it is an ideal weakly interacting and highly penetrating probe of matter's inner structure and dynamics. Unlike techniques using photon electric fields or charged particles (e.g., electrons, muons) that significantly modify the local electronic environment, neutron spectroscopy allows determination of a material's intrinsic, unperturbed physical properties. The method is not sensitive to extraneous charges, electric fields, and the imperfection of surface layers. Because the neutron is a highly penetrating and non-destructive probe, neutron spectroscopy can probe the microscopic properties of bulk materials (not just their surface layers) and study samples embedded in complex environments, such as cryostats, magnets, and pressure cells, which are essential for understanding the physical origins of magnetic phenomena. Neutron scattering is arguably the most powerful and versatile experimental tool for studying the microscopic properties of the magnetic materials. The magnitude of the cross-section of the neutron magnetic scattering is similar to the cross-section of nuclear scattering by short-range nuclear forces, and is large enough to provide measurable scattering by the ordered magnetic structures and electron spin fluctuations. In the half-a-century or so that has passed since neutron beams with sufficient intensity for scattering applications became available with the advent of the nuclear reactors, they have became indispensable tools for studying a variety of important areas of modern

Neutron Scattering

International Nuclear Information System (INIS)

Fayer, Michael J.; Gee, Glendon W.

2005-01-01

The neutron probe is a standard tool for measuring soil water content. This article provides an overview of the underlying theory, describes the methodology for its calibration and use, discusses example applications, and identifies the safety issues. Soil water makes land-based life possible by satisfying plant water requirements, serving as a medium for nutrient movement to plant roots and nutrient cycling, and controlling the fate and transport of contaminants in the soil environment. Therefore, a successful understanding of the dynamics of plant growth, nutrient cycling, and contaminant behavior in the soil requires knowledge of the soil water content as well as its spatial and temporal variability. After more than 50 years, neutron probes remain the most reliable tool available for field monitoring of soil water content. Neutron probes provide integrated measurements over relatively large volumes of soil and, with proper access, allow for repeated sampling of the subsurface at the same locations. The limitations of neutron probes include costly and time-consuming manual operation, lack of data automation, and costly regulatory requirements. As more non-radioactive systems for soil water monitoring are developed to provide automated profiling capabilities, neutron-probe usage will likely decrease. Until then, neutron probes will continue to be a standard for reliable measurements of field water contents in soils around the globe

A neutron beam polarizer for study of parity violation in neutron-nucleus interactions

International Nuclear Information System (INIS)

Penttilae, S.I.; Bowman, J.D.; Frankle, C.M.; Seestrom, S.J.; Yen, Yi-Fen; Delheij, P.P.J.; Haase, D.G.; Postma, H.

1994-01-01

A dynamically-polarized proton target operating at 5 Tesla and 1 K has been built to, neutron beam for studies of parity violation in compound-nuclear resonances. Nearly 0.9 proton polarization was obtained in an electron-beam irradiated ammonia target. This was used to produce a neutron beam polarization of 0.7 at epithermal energies. The combination of the polarized proton target and the LANSCE spallation neutron source produces the most intense pulsed polarized epithermal neutron beam in the world. The neutron-beam polarizer is described and methods to determine neutron beam polarization are presented

Online monitoring of fast neutron (DT/DD) at Purnima neutron generator

International Nuclear Information System (INIS)

Bishnoi, S.; Patel, T.; Shukla, M.; Adhikari, P.S.; Sinha, A.

2012-01-01

A neutron generator (NG) at Purnima Labs, BARC has been developed for DT accelerator driven zero power subcritical (ADSS) system. Subcritical core of ADSS will be coupled to the NG for benchmarking experiments. Kinetic parameters of ADSS such as K-source, flux, power etc depends on this external neutron source strength injected to the core. However the neutron emission rate of NG does not remain stable throughout its operation. In view of this a reliable, precise and online monitoring of NG's neutron emission rate is required. An online neutron monitoring system based on associated particle method has been designed, developed and installed at NG. The monitoring unit consists of an ion implanted planar silicon detector, placed inside the drift tube of NG at an angle with respect to D + beam direction. A series of experiments were carried out with increasing neutron yield to optimize the position of detector such that it has sufficient counting statistics and minimum pileup. A complementary calibration procedure for validating these results based on activation technique was also carried out with standard Cu foil. The reaction rate monitored with online monitor and foil activation technique were compared, their variations with the predicted (theoretical) results were within 16%. This paper deals with the development and performance of online neutron monitoring system for DT and DD neutrons

Neutrons and Nuclear Engineering

International Nuclear Information System (INIS)

Ekkebus, Allen E.

2007-01-01

Oak Ridge National Laboratory hosted two workshops in April 2007 relevant to nuclear engineering education. In the Neutron Stress, Texture, and Phase Transformation for Industry workshop (http://neutrons.ornl.gov/workshops/nst2/), several invited speakers gave examples of neutron stress mapping for nuclear engineering applications. These included John Root of National Research Council of Canada, Mike Fitzpatrick of the UK's Open University, and Yan Gao of GE Global Research on their experiences with industrial and academic uses of neutron diffraction. Xun-Li Wang and Camden Hubbard described the new instruments at ORNL that can be used for such studies. This was preceded by the Neutrons for Materials Science and Engineering educational symposium (http://neutrons.ornl.gov/workshops/edsym2007). It was directed to the broad materials science and engineering community based in universities, industry and laboratories who wish to learn what the neutron sources in the US can provide for enhancing the understanding of materials behavior, processing and joining. Of particular interest was the presentation of Donald Brown of Los Alamos about using 'Neutron diffraction measurements of strain and texture to study mechanical behavior of structural materials.' At both workshops, the ORNL neutron scattering instruments relevant to nuclear engineering studies were described. The Neutron Residual Stress Mapping Facility (NRSF2) is currently in operation at the High Flux Isotope Reactor; the VULCAN Engineering Materials Diffractometer will begin commissioning in 2008 at the Spallation Neutron Source. For characteristics of these instruments, as well as details of other workshops, meetings, capabilities, and research proposal submissions, please visit http://neutrons.ornl.gov. To submit user proposals for time on NRSF2 contact Hubbard at hubbardcratornl.gov

Introduction to neutron stars

Energy Technology Data Exchange (ETDEWEB)

Lattimer, James M. [Dept. of Physics and Astronomy, Stony Brook University, Stony Brook, NY 11794-3800 (United States)

2015-02-24

Neutron stars contain the densest form of matter in the present universe. General relativity and causality set important constraints to their compactness. In addition, analytic GR solutions are useful in understanding the relationships that exist among the maximum mass, radii, moments of inertia, and tidal Love numbers of neutron stars, all of which are accessible to observation. Some of these relations are independent of the underlying dense matter equation of state, while others are very sensitive to the equation of state. Recent observations of neutron stars from pulsar timing, quiescent X-ray emission from binaries, and Type I X-ray bursts can set important constraints on the structure of neutron stars and the underlying equation of state. In addition, measurements of thermal radiation from neutron stars has uncovered the possible existence of neutron and proton superfluidity/superconductivity in the core of a neutron star, as well as offering powerful evidence that typical neutron stars have significant crusts. These observations impose constraints on the existence of strange quark matter stars, and limit the possibility that abundant deconfined quark matter or hyperons exist in the cores of neutron stars.

Study of neutron focusing at the Texas Cold Neutron Source. Final report

International Nuclear Information System (INIS)

Wehring, B.W.; Uenlue, K.

1995-01-01

Funds were received for the first year of a three year DOE Nuclear Engineering Research Grant, ''Study of Neutron Focusing at the Texas Cold Neutron Source'' (FGO2-92ER75711). The purpose of this three year study was to develop a neutron focusing system to be used with the Texas Cold Neutron Source (TCNS) to produce an intense beam of neutrons. A prompt gamma activation analysis (PGAA) facility was also to be designed, setup, and tested under the three year project. During the first year of the DOE grant, a new procedure was developed and used to design a focusing converging guide consisting of truncated rectangular cone sections. Detailed calculations were performed using a 3-D Monte Carlo code which we wrote to trace neutrons through the curved guide of the TCNS into the proposed converging guide. Using realistic reflectivities for Ni-Ti supermirrors, we obtained gains of 3 to 5 for the neutron flux averaged over an area of 1 x 1 cm

Microdosimetry of intermediate energy neutrons in fast neutron fields

International Nuclear Information System (INIS)

Saion, E.B.; Watt, D.E.

1988-01-01

A coaxial double cylindrical proportional counter has been constructed for microdosimetry of intermediate energy neutrons in mixed fields. Details are given of the measured gas gain and resolution characteristics of the counter for a wide range of anode voltages. Event spectra due to intermediate neutrons in any desired energy band is achieved by an appropriate choice of thickness of the common dividing wall in the counter and by appropriate use of the coincidence, anticoincidence pulse counting arrangements. Calculated estimates indicate that the dose contribution by fast neutrons to the energy deposition events in the intermediate neutron range may be as large as 25%. Empirical procedures being investigated aim to determine the necessary corrections to be applied to the microdose distributions, with a precision of 10%. (author)

Neutron capture studies of {sup 206}Pb at a cold neutron beam

Energy Technology Data Exchange (ETDEWEB)

Schillebeeckx, P.; Kopecky, S.; Quetel, C.R.; Tresl, I.; Wynants, R. [Institute for Reference Materials and Measurements, European Commission, Joint Research Centre, Geel (Belgium); Belgya, T.; Szentmiklosi, L. [Institute for Energy Security and Environmental Safety, Centre for Energy Research, Budapest (Hungary); Borella, A. [Institute for Reference Materials and Measurements, European Commission, Joint Research Centre, Geel (Belgium); SCK CEN, Mol (Belgium); Mengoni, A. [Nuclear Data Section, International Atomic Energy Agency (IAEA), Wagramerstrasse 5, PO Box 100, Vienna (Austria); Agenzia Nazionale per le Nuove Tecnologie, l' Energia e lo Sviluppo Economico Sostenibile (ENEA), Bologna (Italy)

2013-11-15

Gamma-ray transitions following neutron capture in {sup 206}Pb have been studied at the cold neutron beam facility of the Budapest Neutron Centre using a metallic sample enriched in {sup 206}Pb and a natural lead nitrate powder pellet. The measurements were performed using a coaxial HPGe detector with Compton suppression. The observed {gamma} -rays have been incorporated into a decay scheme for neutron capture in {sup 206}Pb. Partial capture cross sections for {sup 206}Pb(n, {gamma}) at thermal energy have been derived relative to the cross section for the 1884 keV transition after neutron capture in {sup 14}N. From the average crossing sum a total thermal neutron capture cross section of 29{sup +2}{sub -1} mb was derived for the {sup 206}Pb(n, {gamma}) reaction. The thermal neutron capture cross section for {sup 206}Pb has been compared with contributions due to both direct capture and distant unbound s-wave resonances. From the same measurements a thermal neutron-induced capture cross section of (649 {+-} 14) mb was determined for the {sup 207}Pb(n, {gamma}) reaction. (orig.)

Neutron filters for producing monoenergetic neutron beams

International Nuclear Information System (INIS)

Harvey, J.A.; Hill, N.W.; Harvey, J.R.

1982-01-01

Neutron transmission measurements have been made on high-purity, highly-enriched samples of 58 Ni (99.9%), 60 Ni (99.7%), 64 Zn (97.9%) and 184 W (94.5%) to measure their neutron windows and to assess their potential usefulness for producing monoenergetic beams of intermediate energies from a reactor. Transmission measurements on the Los Alamos Sc filter (44.26 cm Sc and 1.0 cm Ti) have been made to determine the characteristics of the transmitted neutron beam and to measure the total cross section of Sc at the 2.0 keV minimum. When corrected for the Ti and impurities, a value of 0.35 +- 0.03 b was obtained for this minimum

Latest developments of neutron scattering instrumentation at the Juelich Centre for Neutron Science

International Nuclear Information System (INIS)

Ioffe, Alexander

2013-01-01

Jülich Centre for Neutron Science (JCNS) is operating a number of world-class neutron scattering instruments situated at the most powerful and advanced neutron sources (FRM II, ILL and SNS) and is continuously undertaking significant efforts in the development and upgrades to keep this instrumentation in line with the continuously changing scientific request. These developments are mostly based upon the latest progress in neutron optics and polarized neutron techniques. For example, the low-Q limit of the suite of small angle-scattering instruments has been extended to 4·10 -5 Å -1 by the successful use of focusing optics. A new generation of correction elements for the neutron spin-echo spectrometer has allowed for the use of the full field integral available, thus pushing further the instrument resolution. A significant progress has been achieved in the developments of 3 He neutron spin filters for purposes of the wide-angle polarization analysis for off-specular reflectometry and (grazing incidence) small-angle neutron scattering, e.g. the on-beam polarization of 3 He in large cells is allowing to achieve a high neutron beam polarization without any degradation in time. The wide Q-range polarization analysis using 3 He neutron spin filters has been implemented for small-angle neutron scattering that lead to the reduction up to 100 times of the intrinsic incoherent background from non-deuterated biological molecules. Also the work on wide-angle XYZ magnetic cavities (Magic PASTIS) will be presented. (author)

Effect of neutrons scattered from boundary of neutron field on shielding experiment

International Nuclear Information System (INIS)

Ogawa, Tatsuhiko; Abe, Takuya; Kosako, Toshiso; Iimoto, Takeshi

2009-01-01

Neutron shielding experiment with 49 cm-thick ordinary concrete was carried out at the reactor 'Yayoi' The University of Tokyo. System of this experiment is enclosed by heavy concrete where neutrons backscattered from heavy concrete likely affected neutron flux on the back surface of shielding concrete. Reaction rate of 197 Au(n, γ), cadmium covered 197 Au(n, γ) and 115 In(n, n') in the shielding concrete was measured using foil activation method. Neutron transport calculation was carried out in order to simulate reaction rate by calculating neutron spectra and convoluting with neutron capture cross-section in neutron shielding concrete. Comparison was made between calculated reaction rate and experimental one, and almost satisfactory agreement was found except for the back surface of shielding. To compose adequate simulation model, description of heavy concrete behind the shielding was thought to be of importance. For example, disregarding neutrons backscattered from heavy concrete, calculation underestimated reaction rate by the factor of 10. In another example, assuming that chemical composition of heavy concrete is equal to the composition adopted from a literature, the reaction rate was overestimated by factor of 5. By making the composition of heavy concrete equal to that based on facility design, overestimation was found to be the factor of 2. Therefore, adequate description of chemical composition of heavy concrete is found to be of importance in order to simulate neutron induced reaction rate on the back surface of neutron shielding concrete in shielding experiment performed in a system enclosed by heavy concrete. (author)

Neutron resonance spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Gunsing, F

2005-06-15

The present document has been written in order to obtain the diploma 'Habilitation a Diriger des Recherches'. Since this diploma is indispensable to supervise thesis students, I had the intention to write a document that can be useful for someone starting in the field of neutron resonance spectroscopy. Although the here described topics are already described elsewhere, and often in more detail, it seemed useful to have most of the relevant information in a single document. A general introduction places the topic of neutron-nucleus interaction in a nuclear physics context. The large variations of several orders of magnitude in neutron-induced reaction cross sections are explained in terms of nuclear level excitations. The random character of the resonances make nuclear model calculation predictions impossible. Then several fields in physics where neutron-induced reactions are important and to which I have contributed in some way or another, are mentioned in a first synthetic chapter. They concern topics like parity nonconservation in certain neutron resonances, stellar nucleosynthesis by neutron capture, and data for nuclear energy applications. The latter item is especially important for the transmutation of nuclear waste and for alternative fuel cycles. Nuclear data libraries are also briefly mentioned. A second chapter details the R-matrix theory. This formalism is the foundation of the description of the neutron-nucleus interaction and is present in all fields of neutron resonance spectroscopy. (author)

Double-layer neutron shield design as neutron shielding application

Science.gov (United States)

Sariyer, Demet; Küçer, Rahmi

2018-02-01

The shield design in particle accelerators and other high energy facilities are mainly connected to the high-energy neutrons. The deep penetration of neutrons through massive shield has become a very serious problem. For shielding to be efficient, most of these neutrons should be confined to the shielding volume. If the interior space will become limited, the sufficient thickness of multilayer shield must be used. Concrete and iron are widely used as a multilayer shield material. Two layers shield material was selected to guarantee radiation safety outside of the shield against neutrons generated in the interaction of the different proton energies. One of them was one meter of concrete, the other was iron-contained material (FeB, Fe2B and stainless-steel) to be determined shield thicknesses. FLUKA Monte Carlo code was used for shield design geometry and required neutron dose distributions. The resulting two layered shields are shown better performance than single used concrete, thus the shield design could leave more space in the interior shielded areas.

Pulsed neutron generator for mass flow measurement using the pulsed neutron activation technique

International Nuclear Information System (INIS)

Rochau, G.E.; Hornsby, D.R.; Mareda, J.F.; Riggan, W.C.

1980-01-01

A high-output, transportable neutron generator has been developed to measure mass flow velocities in reactor safety tests using the Pulsed Neutron Activation (PNA) Technique. The PNA generator produces >10 10 14 MeV D-T neutrons in a 1.2 millisecond pulse. The Millisecond Pulse (MSP) Neutron Tube, developed for this application, has an expected operational life of 1000 pulses, and it limits the generator pulse repetition rate to 12 pulses/minute. A semiconductor neutron detector is included in the generator package to monitor the neutron output. The control unit, which can be operated manually or remotely, also contains a digital display with a BCD output for the neutron monitor information. The digital logic of the unit controls the safety interlocks and rejects transient signals which could accidently fire the generator

Neutron techniques in Safeguards

International Nuclear Information System (INIS)

Zucker, M.S.

1982-01-01

An essential part of Safeguards is the ability to quantitatively and nondestructively assay those materials with special neutron-interactive properties involved in nuclear industrial or military technology. Neutron techniques have furnished most of the important ways of assaying such materials, which is no surprise since the neutronic properties are what characterizes them. The techniques employed rely on a wide selection of the many methods of neutron generation, detection, and data analysis that have been developed for neutron physics and nuclear science in general

Neutron scattering. Experiment manuals

International Nuclear Information System (INIS)

Brueckel, Thomas; Heger, Gernot; Richter, Dieter; Roth, Georg; Zorn, Reiner

2012-01-01

The following topics are dealt with: The thermal triple-axis spectrometer PUMA, the high-resolution powder diffractometer SPODI, the hot single-crystal diffractometer HEiDi for structure analysis with neutrons, the backscattering spectrometer SPHERES, the neutron polarization analyzer DNS, the neutron spin-echo spectrometer J-NSE, the small-angle neutron diffractometers KWS-1/-2, the very-small-angle neutron diffractometer with focusing mirror KWS-3, the resonance spin-echo spectrometer RESEDA, the reflectometer TREFF, the time-of-flight spectrometer TOFTOF. (HSI)

Neutron monitoring for radiological protection

International Nuclear Information System (INIS)

Gibson, J.A.B.

1985-01-01

Neutron monitoring is a subject of increasing general interest and considerable attention is being paid to the development of improved techniques and methods for neutron monitoring. The Agency, therefore, considered it important to prepare a guide on the subject of neutron monitoring for radiation protection purposes. The present Manual is intended for those persons or authorities in Member States, particularly developing countries, who are responsible for the organization of neutron monitoring programmes and practical neutron monitoring. This Manual consequently, deals with topics such as neutron dosimetry, sources of neutrons and neutron detection as well as field instruments and operational systems used in this context

Particle physics with cold neutrons

International Nuclear Information System (INIS)

Dubbers, D.

1991-01-01

Slow neutrons are used in a large number of experiments to study the physics of particles and their fundamental interactions. Some of these experiments search for manifestations of ''new physics'' like baryon- or lepton-number nonconservation, time reversal nonconservation, new particles, right-handed currents, nonzero neutron charge, nonlinear terms in the Schrodinger equation, exotic e + e - states, and others. Other slow neutron experiments test the present Standard Model. The parity nonconserving weak neutron-nucleon interaction is studied in a variety of experiments. Free neutron beta decay gives precise values for the weak vector and axialvector coupling constants, which allow precise tests of basic symmetries like the conservation of the weak vector current, the unitarity of the weak quark mixing matrix, SU(3) flavour symmetry, and right-handed currents. Neutron beta decay data are further needed to calculate weak cross-sections, for applications, in big bang cosmology, in astrophysics, in solar physics and the solar neutrino problem, and in such mundane things as neutrino detection efficiencies in neutrino oscillation or proton decay experiments. Neutron-nucleon, neutron-nucleus and neutron-electron scattering lengths are determined in high precision experiments, which use methods like neutron interferometry or neutron gravity spectrometry. The experiments give information on quantities like the neutron charge radius or the neutron electric polarizability. Precision measurements of other fundamental constants lead to a better, model-independent value of the fine structure constant. Finally, the fundamental experiments on quantum mechanics, like spinor 4π -rotation, Berry's phase, dressed neutrons, Aharanov - Casher effect, or gravitational effects on the neutron's phase will be briefly discussed. (author)

Wide range neutron detection system

International Nuclear Information System (INIS)

Todt, W.H. Sr.

1978-01-01

A neutron detection system for reactor control is described which is operable over a wide range of neutron flux levels. The system includes a fission type ionization chamber neutron detector, means for gamma and alpha signal compensation, and means for operating the neutron detector in the pulse counting mode for low neutron flux levels, and in the direct current mode for high neutron flux levels

Experiments on neutron-proton and neutron-electron interaction

International Nuclear Information System (INIS)

Koester, L.

1975-01-01

The paper reports on zero-energy experiments with neutrons, protons and electrons with a wavelength that is considerably longer than the particle expansion. Scattering amplitudes are measured for the reactions n + p and n + e. A neutron gravity refractometer is used. (WL/AK) [de

Measurement of neutron sensitivity of self powered neutron detectors

International Nuclear Information System (INIS)

Mahant, A.K.; Yeshuraja, V.; Ghodke, Shobha

2005-01-01

Self powered neutron detectors (SPNDs ) will form the part of Reactor Instrumentation in the upcoming 500 MWe power reactors. ECIL has developed Vanadium and Cobalt SPNDs for NPCIL to be used in regulation and protection channels. Experimental determination of neutron sensitivity of the vanadium and cobalt Self Powered Neutron Detectors (SPNDs) was carried out in A-l location of Apsara reactor at BARC. The measurements involved determination of total detector signal, its various components and the thermal neutron flux at the detector location. The paper describes the experimental techniques used to measure various parameters required to evaluate the neutron sensitivity of the SPNDs and also the parameters required to ascertain the integrity of SPNDs. Neutron flux measurement was done by gold foil irradiation technique. The predominant signal component from the vanadium SPND is Ib the current due to activation of the vanadium emitter, it forms about 85% of the total signal. The other components I n,γ due to the capture gamma rays of 52 V and I externalγ produced by the external reactor gamma rays contribute about 10% and 5% respectively to the total signal. Whereas in the cobalt SPND the main signal component is due to the capture gamma rays of 60 Co and accounts for about the 95% of the total signal. Remaining 5% signal is due to external reactor gamma rays. (author)

Neutron-deuteron breakup experiment at En=13 MeV: Determination of the 1S0 neutron-neutron scattering length ann

International Nuclear Information System (INIS)

Gonzalez Trotter, D.E.; Meneses, F. Salinas; Tornow, W.; Howell, C.R.; Chen, Q.; Crowell, A.S.; Roper, C.D.; Walter, R.L.; Schmidt, D.; Witala, H.; Gloeckle, W.; Tang, H.; Zhou, Z.; Slaus, I.

2006-01-01

We report on results of a kinematically complete neutron-deuteron breakup experiment performed at Triangle Universities Nuclear Laboratory using an E n =13 MeV incident neutron beam. The 1 S 0 neutron-neutron scattering length a nn has been determined for four production angles of the neutron-neutron final-state interaction configuration. The absolute cross-section data were analyzed with rigorous three-nucleon calculations. Our average value of a nn =-18.7±0.7 fm is in excellent agreement with a nn =-18.6±0.4 fm obtained from capture experiments of negative pions on deuterons. We also performed a shape analysis of the final-state interaction cross-section enhancements by allowing the normalization of the data to float. From these relative data, we obtained an average value of a nn =-18.8±0.5 fm, in agreement with the result obtained from the absolute cross-section measurements. Our result deviates from the world average of a nn =-16.7±0.5 fm determined from previous kinematically complete neutron-deuteron breakup experiments, including the most recent one carried out at Bonn. However, this low value for a nn is at variance with theoretical expectation and other experimental information about the sign of charge-symmetry breaking of the nucleon-nucleon interaction. In agreement with theoretical predictions, no evidence was found of significant three-nucleon force effects on the neutron-neutron final-state interaction cross sections

NEUTRON AND PHOTON DOSE MAPPING OF A DD NEUTRON GENERATOR.

Science.gov (United States)

Metwally, Walid A; Taqatqa, Osama A; Ballaith, Mohammed M; Chen, Allan X; Piestrup, Melvin A

2017-11-01

Neutron generators are an excellent tool that can be effectively utilized in educational institutions for applications such as neutron activation analysis, neutron radiography, and profiling and irradiation effects. For safety purposes, it is imperative that appropriate measures are taken in order to minimize the radiation dose from such devices to the operators, students and the public. This work presents the simulation and measurement results for the neutron and photon dose rates in the vicinity of the neutron generator installed at the University of Sharjah. A very good agreement is found between the simulated and measured dose rates. All of the public dose constraints were found to be met. The occupational dose constraint was also met after imposing a 200 cm no entry zone around the generator room. © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

An empirical formula for scattered neutron components in fast neutron radiography

International Nuclear Information System (INIS)

Dou Haifeng; Tang Bin

2011-01-01

Scattering neutrons are one of the key factors that may affect the images of fast neutron radiography. In this paper, a mathematical model for scattered neutrons is developed on a cylinder sample, and an empirical formula for scattered neutrons is obtained. According to the results given by Monte Carlo methods, the parameters in the empirical formula are obtained with curve fitting, which confirms the logicality of the empirical formula. The curve-fitted parameters of common materials such as 6 LiD are given. (authors)

Neutron Science 21

International Nuclear Information System (INIS)

Park, Sung Il; Choi, Yong Nam; Ahn, Geun Young; Lee, Hee Joo; Hong, Ji Sun; Kim, Hyo Sun

2009-01-01

The project aims to make the HANARO neutron beam facility a neutron research hub in the Asia-Pacific. This is a part of the effort to make the facility as productive as other neutron beam facilities in America and Europe which already operate as a hub that attracts thousands of users and produces hundreds of publications annually. The projects promotes 1) collaborative research between HANARO personnel and users, 2) internationally collaboration on various fronts of neutron science related activities. To achieve the above in an effective manner, its direction is adjusted by a series of meetings and the activities of the project are advertised to the public media. 3 domestic and 1 international collaborative research was carried out successfully in 2008 by using the HRPD. The 1st Asia-Oceania Neutron Summer School was successfully hosted in Korea. The annual report of the HANARO neutron beam facility was published. 3 advisory meetings and 6 internal meetings to promote the hub were held. Users were surveyed on their needs. The media was contacted twice in an effort to advertise the project activities. All of the above achievements are directly applicable to determining the national policy on neutron science. It is advised that the KAERI management take notice of the results to manage the facility effectively

The world’s first pelletized cold neutron moderator at a neutron scattering facility

Energy Technology Data Exchange (ETDEWEB)

Ananiev, V.; Belyakov, A.; Bulavin, M.; Kulagin, E.; Kulikov, S.; Mukhin, K.; Petukhova, T.; Sirotin, A.; Shabalin, D.; Shabalin, E.; Shirokov, V.; Verhoglyadov, A., E-mail: verhoglyadov_al@mail.ru

2014-02-01

In July 10, 2012 cold neutrons were generated for the first time with the unique pelletized cold neutron moderator CM-202 at the IBR-2M reactor. This new moderator system uses small spherical beads of a solid mixture of aromatic hydrocarbons (benzene derivatives) as the moderating material. Aromatic hydrocarbons are known as the most radiation-resistant hydrogenous substances and have properties to moderate slow neutrons effectively. Since the new moderator was put into routine operation in September 2013, the IBR-2 research reactor of the Frank Laboratory of Neutron Physics has consolidated its position among the world’s leading pulsed neutron sources for investigation of matter with neutron scattering methods.

Non-destructive diagnostics of irradiated materials using neutron scattering from pulsed neutron sources

Energy Technology Data Exchange (ETDEWEB)

Korenev, Sergey E-mail: sergey_korenev@steris.com; Sikolenko, Vadim

2004-10-01

The advantage of neutron-scattering studies as compared to the standard X-ray technique is the high penetration of neutrons that allow us to study volume effects. The high resolution of instrumentation on the basis neutron scattering allows measurement of the parameters of lattice structure with high precision. We suggest the use of neutron scattering from pulsed neutron sources for analysis of materials irradiated with pulsed high current electron and ion beams. The results of preliminary tests using this method for Ni foils that have been studied by neutron diffraction at the IBR-2 (Pulsed Fast Reactor at Joint Institute for Nuclear Research) are presented.

Non-destructive diagnostics of irradiated materials using neutron scattering from pulsed neutron sources

Science.gov (United States)

Korenev, Sergey; Sikolenko, Vadim

2004-09-01

The advantage of neutron-scattering studies as compared to the standard X-ray technique is the high penetration of neutrons that allow us to study volume effects. The high resolution of instrumentation on the basis neutron scattering allows measurement of the parameters of lattice structure with high precision. We suggest the use of neutron scattering from pulsed neutron sources for analysis of materials irradiated with pulsed high current electron and ion beams. The results of preliminary tests using this method for Ni foils that have been studied by neutron diffraction at the IBR-2 (Pulsed Fast Reactor at Joint Institute for Nuclear Research) are presented.

A neutron beam polarizer for study of parity violation in neutron-nucleus interactions

International Nuclear Information System (INIS)

Penttilae, S.I.; Bowman, J.D.; Delheij, P.P.; Frankle, C.M.; Haase, D.G.; Postma, H.; Seestrom, S.J.; Yen, Y.

1995-01-01

A dynamically-polarized proton target operating at 5 Tesla and 1 K has been built to polarize an epithermal neutron beam for studies of parity violation in compound-nuclear resonances. Nearly 0.9 proton polarization was obtained in an electron-beam irradiated ammonia target. This was used to produce a neutron beam polarization of 0.7 at epithermal energies. The combination of the polarized proton target and the LANSCE spallation neutron source produces the most intense pulsed polarized epithermal neutron beam in the world. The neutron-beam polarizer is described and methods to determine neutron beam polarization are presented. copyright 1995 American Institute of Physics

Neutronic Design Calculations on Moderators for the Spallation Neutron Source (SNS)

International Nuclear Information System (INIS)

Murphy, D.B.

1999-01-01

The Spallation Neutron Source (SNS) to be built at the Oak Ridge National Laboratory will provide an intense source of neutrons for a large variety of experiments. It consists of a high-energy (1-GeV) and high-power (∼1-MW) proton accelerator, an accumulator ring, together with a target station and an experimental area. In the target itself, the proton beam will produce neutrons via the spallation process and these will be converted to low-energy ( 2 O moderators. Extensive engineering design work has been conducted on the moderator vessels. For our studies we have produced realistic neutronic representations of these moderators. We report on neutronic studies conducted on these representations of the moderators using Monte Carlo simulation techniques

Biomedical neutron research at the Californium User Facility for neutron science

International Nuclear Information System (INIS)

Martin, R.C.; Byrne, T.E.; Miller, L.F.

1997-01-01

The Californium User Facility for Neutron Science has been established at Oak Ridge National Laboratory (ORNL). The Californium User Facility (CUF) is a part of the larger Californium Facility, which fabricates and stores compact 252 Cf neutron sources for worldwide distribution. The CUF can provide a cost-effective option for research with 252 Cf sources. Three projects at the CUF that demonstrate the versatility of 252 Cf for biological and biomedical neutron-based research are described: future establishment of a 252 Cf-based neutron activation analysis system, ongoing work to produce miniature high-intensity, remotely afterloaded 252 Cf sources for tumor therapy, and a recent experiment that irradiated living human lung cancer cells impregnated with experimental boron compounds to test their effectiveness for boron neutron capture therapy

ATR neutron spectral characterization

Energy Technology Data Exchange (ETDEWEB)

Rogers, J.W.; Anderl, R.A.

1995-11-01

The Advanced Test Reactor (ATR) at INEL provides intense neutron fields for irradiation-effects testing of reactor material samples, for production of radionuclides used in industrial and medical applications, and for scientific research. Characterization of the neutron environments in the irradiation locations of the ATR has been done by means of neutronics calculations and by means of neutron dosimetry based on the use of neutron activation monitors that are placed in the various irradiation locations. The primary purpose of this report is to present the results of an extensive characterization of several ATR irradiation locations based on neutron dosimetry measurements and on least-squares-adjustment analyses that utilize both neutron dosimetry measurements and neutronics calculations. This report builds upon the previous publications, especially the reference 4 paper. Section 2 provides a brief description of the ATR and it tabulates neutron spectral information for typical irradiation locations, as derived from the more historical neutron dosimetry measurements. Relevant details that pertain to the multigroup neutron spectral characterization are covered in section 3. This discussion includes a presentation on the dosimeter irradiation and analyses and a development of the least-squares adjustment methodology, along with a summary of the results of these analyses. Spectrum-averaged cross sections for neutron monitoring and for displacement-damage prediction in Fe, Cr, and Ni are given in section 4. In addition, section4 includes estimates of damage generation rates for these materials in selected ATR irradiation locations. In section 5, the authors present a brief discussion of the most significant conclusions of this work and comment on its relevance to the present ATR core configuration. Finally, detailed numerical and graphical results for the spectrum-characterization analyses in each irradiation location are provided in the Appendix.

Genetic effect of neutrons

International Nuclear Information System (INIS)

Luchnik, N.V.; Sevan'kaev, A.V.; Fesenko, Eh.V.

1984-01-01

Gene mutations resulting from neutron effect are considered, but attention is focused on chromosome mutations. Dose curves for different energy of neutrons obtained at different objects are obtained which makes it possible to consider RBE of neutrons depending on their energy and radiation dose and to get some information on the neutron effect on heredity

Lunar neutron source function

International Nuclear Information System (INIS)

Kornblum, J.J.

1974-01-01

The search for a quantitative neutron source function for the lunar surface region is justified because it contributes to our understanding of the history of the lunar surface and of nuclear process occurring on the moon since its formation. A knowledge of the neutron source function and neutron flux distribution is important for the interpretation of many experimental measurements. This dissertation uses the available pertinent experimental measurements together with theoretical calculations to obtain an estimate of the lunar neutron source function below 15 MeV. Based upon reasonable assumptions a lunar neutron source function having adjustable parameters is assumed for neutrons below 15 MeV. The lunar neutron source function is composed of several components resulting from the action of cosmic rays with lunar material. A comparison with previous neutron calculations is made and significant differences are discussed. Application of the results to the problem of lunar soil histories is examined using the statistical model for soil development proposed by Fireman. The conclusion is drawn that the moon is losing mass

Bouncing neutrons and the neutron centrifuge

International Nuclear Information System (INIS)

Watson, P J S

2003-01-01

The recent observation of the quantum state of the neutron bouncing freely under gravity allows some novel experiments. A possible method of purifying the ground state is given. We investigate two possible applications. It appears that the state could not be used to set better limits on the electric dipole moment of the neutron. However, it would be possible to use the state to set limits on modifications of gravity at short distances

Grazing Incidence Neutron Optics

Science.gov (United States)

Gubarev, Mikhail V. (Inventor); Ramsey, Brian D. (Inventor); Engelhaupt, Darell E. (Inventor)

2013-01-01

Neutron optics based on the two-reflection geometries are capable of controlling beams of long wavelength neutrons with low angular divergence. The preferred mirror fabrication technique is a replication process with electroform nickel replication process being preferable. In the preliminary demonstration test an electroform nickel optics gave the neutron current density gain at the focal spot of the mirror at least 8 for neutron wavelengths in the range from 6 to 20.ANG.. The replication techniques can be also be used to fabricate neutron beam controlling guides.

A proposal on evaluation method of neutron absorption performance to substitute conventional neutron attenuation test

International Nuclear Information System (INIS)

Kim, Je Hyun; Shim, Chang Ho; Kim, Sung Hyun; Choe, Jung Hun; Cho, In Hak; Park, Hwan Seo; Park, Hyun Seo; Kim, Jung Ho; Kim, Yoon Ho

2016-01-01

For a verification of newly-developed neutron absorbers, one of guidelines on the qualification and acceptance of neutron absorbers is the neutron attenuation test. However, this approach can cause a problem for the qualifications that it cannot distinguish how the neutron attenuates from materials. In this study, an estimation method of neutron absorption performances for materials is proposed to detect both direct penetration and back-scattering neutrons. For the verification of the proposed method, MCNP simulations with the experimental system designed in this study were pursued using the polyethylene, iron, normal glass and the vitrified form. The results show that it can easily test neutron absorption ability using single absorber model. Also, from simulation results of single absorber and double absorbers model, it is verified that the proposed method can evaluate not only the direct thermal neutrons passing through materials, but also the scattered neutrons reflected to the materials. Therefore, the neutron absorption performances can be accurately estimated using the proposed method comparing with the conventional neutron attenuation test. It is expected that the proposed method can contribute to increase the reliability of the performance of neutron absorbers

A proposal on evaluation method of neutron absorption performance to substitute conventional neutron attenuation test

Energy Technology Data Exchange (ETDEWEB)

Kim, Je Hyun; Shim, Chang Ho [Dept. of Nuclear Engineering, Hanyang University, Seoul (Korea, Republic of); Kim, Sung Hyun [Nuclear Fuel Cycle Waste Treatment Research Division, Research Reactor Institute, Kyoto University, Osaka (Japan); Choe, Jung Hun; Cho, In Hak; Park, Hwan Seo [Ionizing Radiation Center, Nuclear Fuel Cycle Waste Treatment Research Division, Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Park, Hyun Seo; Kim, Jung Ho; Kim, Yoon Ho [Ionizing Radiation Center, Korea Research Institute of Standards and Science, Daejeon (Korea, Republic of)

2016-12-15

For a verification of newly-developed neutron absorbers, one of guidelines on the qualification and acceptance of neutron absorbers is the neutron attenuation test. However, this approach can cause a problem for the qualifications that it cannot distinguish how the neutron attenuates from materials. In this study, an estimation method of neutron absorption performances for materials is proposed to detect both direct penetration and back-scattering neutrons. For the verification of the proposed method, MCNP simulations with the experimental system designed in this study were pursued using the polyethylene, iron, normal glass and the vitrified form. The results show that it can easily test neutron absorption ability using single absorber model. Also, from simulation results of single absorber and double absorbers model, it is verified that the proposed method can evaluate not only the direct thermal neutrons passing through materials, but also the scattered neutrons reflected to the materials. Therefore, the neutron absorption performances can be accurately estimated using the proposed method comparing with the conventional neutron attenuation test. It is expected that the proposed method can contribute to increase the reliability of the performance of neutron absorbers.

Fundamental neutron physics

International Nuclear Information System (INIS)

Deslattes, R.; Dombeck, T.; Greene, G.; Ramsey, N.; Rauch, H.; Werner, S.

1984-01-01

Fundamental physics experiments of merit can be conducted at the proposed intense neutron sources. Areas of interest include: neutron particle properties, neutron wave properties, and fundamental physics utilizing reactor produced γ-rays. Such experiments require intense, full-time utilization of a beam station for periods ranging from several months to a year or more

Spallation neutron sources

International Nuclear Information System (INIS)

Fraser, J.S.; Bartholomew, G.A.

1983-01-01

The principles and theory of spallation neutron sources are outlined and a comparison is given with other types of neutron source. A summary of the available accelerator types for spallation neutron sources and their advantages and disadvantages is presented. Suitable target materials are discussed for specific applications, and typical target assemblies shown. (U.K.)

Extension of the AUS reactor neutronics system for application to fusion blanket neutronics

International Nuclear Information System (INIS)

Robinson, G.S.

1984-03-01

The AUS modular code scheme for reactor neutronics computations has been extended to apply to fusion blanket neutronics. A new group cross-section library with 200 neutron groups, 37 photon groups and kerma factor data has been generated from ENDF/B-IV. The library includes neutron resonance subgroup parameters and temperature-dependent data for thermal neutron scattering matrices. The validity of the overall calculation system for fusion applications has been checked by comparison with a number of published conceptual design studies