Fiscal 2000 coal engineer training project. Report on senior course; 2000 nendo sekitan gijutsusha yosei jigyo jokyu course hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The above-named course consisted of three weeks of lectures and three months of visits to coal mines and harbor facilities and tours to coal consumers such as power stations and steel manufacturing plants. The report has turned out to be an introductory manual on coal mining consisting of coal mining technologies such as coal resource exploration, coal mining, and coal preparation, and the state of Australian coal industry. The manual comprises (1) job training in Japan (attendance at lectures), (2) inspection and training in Japan (coal consumers), (3) intensified lectures at University of New South Wales (coal mining and preparation), (4) current state of Austrian coal industry, (5) inspection tours to Australian coal mines, (6) inspection tours to Australian harbor facilities, and (7) the state of Australian coal mine management. Fifteen intensified lectures were given, including the 'Overview of Australian coal industry' and 'Coal handling and transport.' Nine coal mines were visited in Queensland, and 21 in New South Wales. As for the state of Australian coal mine management, there is a trend toward contract mining but self-mining constitutes the mainstream. (NEDO)

Survey report. New energy vision formulation project for Osa Town, Okayama Prefecture; 2001 nendo Osa cho shin energy vision sakutei tou jigyo chosa hokokusho. Chiiki shin energy vision sakutei tou jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-02-01

A New Energy Vision was formulated for Osa Town after investigations about energy demand, new energy reserves, and their available amounts. The town consumes approximately 50.6-billion kcal in total, with automobiles consuming a half thereof as fuel. Studies were made about new energy reserves and recoverable amounts in the town, and then an estimation was made that 16.2 times 10{sup 5} kWh/year would be recoverable from photovoltaic energy, 1.58 times 10{sup 5} kWh from small-scale hydropower, 8.79 times 10{sup 6} kWh from ligneous biomass, and 1.96 times 10{sup 5} kWh from livestock biomass, and that 40 MW, for example, would come from wind power, subject to change depending on the wind power generator system to be built. Projects for new energy introduction were discussed, which involved the use of biodiesel fuel for official vehicles, installation of solar hot water showers in primary and junior high schools, application of photovoltaic/wind power to crime prevention lights and street lamps, snow melting systems for roads utilizing geothermal energy, use of heat from thinnings and ligneous waste, wind power facilities, small-scale hydropower facilities, introduction of new energy appliances into sightseeing facilities, and the introduction of photovoltaic power or the like into public facilities. (NEDO)

Fiscal 1997 research report. Basic research project on improving energy consumption efficiency in developing countries (Database construction); 1998 nendo hatten tojokoku energy shohi koritsuka kiso chosa jigyo hokokusho. Database kochiku jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

The New Energy and Industrial Technology Development Organization (NEDO) in fiscal 1993 started a database construction project, which involves energy conservation related primary information on the 11 countries concerned, for encouraging 11 Asian countries, namely, Japan, China, Indonesia, the Philippines, Thailand, Malaysia, Taiwan, Korea, Vietnam, Myanmar, and Pakistan, to promote their energy conservation endeavors. As part of the database construction effort under this research project, the so-far accomplished collection of and analysis into energy related information about the countries, surveys of the utilization and popularization of databases, and development of database systems are taken into consideration. On the basis of these efforts to improve on the database systems for enhanced operability, a program is formulated for database diffusion under which data are collected and updated for storage in databases. Also exerted under the program are endeavors to make use of the above-said database systems and to disseminate the constructed databases into the 11 countries for effective utilization. In the future, it is desired that the NEDO database will win popularity in the 11 countries and be utilized in their formulation of domestic energy conservation policies. (NEDO)

New energy vision of the Gushikami Village area; 2001 nendo Gushikami son chiiki shin energy vision sakutei tou jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-02-01

For the purpose of promoting the introduction of new energy and enhancing the awareness of it in Gushikami Village, Okinawa Prefecture, an investigational study was conducted of the energy demand of the village, existence amount of new energy, plan for new energy introduction, etc., and a vision was worked out. The energy demand of Gushikami Village was estimated at 640.2 x 10{sup 6} MJ/y. By sector, it consisted of 37.1% in the transportation sector, 32.0% in the commercial/residential sector and 30.8% in the industrial sector. The rate of energy source was 73.7% of petroleum-base fuel and 26.3% of electric power. As the plan for new energy introduction, the following were studied: introduction of photovoltaic power generation to the village office/museum/elementary school/junior high school, introduction of solar heat utilization facilities to the meal providing center/gymnasium, introduction of wind power generation to the sports park, project of wind power generation on the sugar cane hill (600kW x 6 turbines), cogeneration by composting of stockbreeding waste and methane, introduction of clean energy car to official vehicle, introduction of natural gas vehicle, installation of experimental plant for conversion of sugar cane to methanol, etc. (NEDO)

NEDO business outline for fiscal 1997. 18th project report meeting; 1997 nendo gyomu gaiyo. Dai 18 kai jigyo hokokukai

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-09-22

The projects of NEDO (New Energy and Industrial Technology Development Organization) are stated as reported at the 18th project report meeting. Outlined are new energy-related projects involving technology development, resources exploitation, promotion of new energy introduction, promotion of international cooperation, gathering of information, and so on. Outlined in relation to the research and development of industrial technologies are projects on research and development, development of medical and welfare equipment, research and development of global environment-related industrial technology, development of international industrial technology, and improvement on platforms for researches. Concerning coal, subsidy-granted projects on domestic coal and projects on domestic coal mine improvement are outlined. Projects relating to compensation for environmental pollution resulting from coal mining and those relating to alcohol production are also outlined. NEDO's financial statement for fiscal 1997 is reported. Also reported are budgets for fiscal 1998 for projects relating to new energy, research and development of industrial technology, coal mining structure coordination, compensation for environmental pollution resulting from coal mining, and alcohol production. (NEDO)

NEDO business outline for fiscal 1997. 18th project report meeting; 1997 nendo gyomu gaiyo. Dai 18 kai jigyo hokokukai

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-09-22

The projects of NEDO (New Energy and Industrial Technology Development Organization) are stated as reported at the 18th project report meeting. Outlined are new energy-related projects involving technology development, resources exploitation, promotion of new energy introduction, promotion of international cooperation, gathering of information, and so on. Outlined in relation to the research and development of industrial technologies are projects on research and development, development of medical and welfare equipment, research and development of global environment-related industrial technology, development of international industrial technology, and improvement on platforms for researches. Concerning coal, subsidy-granted projects on domestic coal and projects on domestic coal mine improvement are outlined. Projects relating to compensation for environmental pollution resulting from coal mining and those relating to alcohol production are also outlined. NEDO's financial statement for fiscal 1997 is reported. Also reported are budgets for fiscal 1998 for projects relating to new energy, research and development of industrial technology, coal mining structure coordination, compensation for environmental pollution resulting from coal mining, and alcohol production. (NEDO)

FY 2001 report on the coal engineer training project. Advanced course; 2001 nendo sekitan gijutsusha yose jigyo. Jokyu kosu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

The paper summed up the details of the training in the coal engineer training project (advanced course) carried out in FY 2001. The term of training was from June 1 to November 14, 2001. In the business training, lectures were given on coal geology, coal exploration technology, coal mining technology, draft survey, coal sampling and analysis method, maritime freight transport mainly of coal, coal utilization technology, environmental protection technology related to coal utilization, projects on overseas coal development, physical properties/chemical characteristics and usage of coal, and coal situation in China. In the inspection training, inspectional visits were paid to Taiheiyo Coal Mining Co., Noshiro Power Plant of the Tohoku Electric Power Co., Kumagaya Plant of Taiheiyo Cement Corp. and Keihin Steelworks of NKK Corp. In the training overseas, inspectional visits were paid to the following in Australia: coal mines of Moonee, Rix's Creek, West Wallsend, Bloomfield, Beltana, Bulga, South Bulga, Mt. Thorley, Warkworth, Liddell, Wambo, Mount Owen, Camberwell, etc. and harbors of Port Newcastle, Port Kembla Coal Terminal, etc. (NEDO)

FY 2000 report on the promotion projects by Research Institute of Innovative Technology for the Earth. Projects for international research exchanges and international seminars; 2000 nendo chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo chosa hokokusho. Kokusai kenkyu koryu jigyo / kokusai seminar kaisai jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the results of the international research exchange projects promoted by Research Institute of Innovative Technology for the Earth (RITE) in FY 2000. The international research exchanges are important for creation of new research areas and technological systems for solving the global environmental problems. In order to promote these activities, RITE invites and dispatches researchers to international conferences and symposiums, promotes research exchanges with major foreign research institutes and academic organizations, and invites and dispatches researchers for medium to long periods. These projects promote exchanges of the latest researches with various institutes, both domestic and foreign, and confirm that the research and development projects now RITE is promoting are closely related to those promoted by various organizations. In the FY 2000, RITE invites 5 foreign researchers for joint researches, and invites 3 foreign researchers to international conferences. RITE also dispatches 3 Japanese researchers to American and European universities, and 12 Japanese researchers to international conferences and the like, to effectively promote the domestic researches and grasp development tendencies at institutes of various countries. RITE holds 5 international seminars for exchanging and discussing broad topics over advanced researches related to global environmental technologies by researchers, both domestic and foreign. (NEDO)

FY 2000 international exchange project on exchanges of engineers - Coal mine technology field. Overseas workshop (Indonesia); 2000 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya) kokusai koryu jigyo. Kaigai workshop (Indonesia)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of making effective technology exchanges and surveying levels of technology in Indonesia and the needs and possibilities of technology transfer from Japan, workshop was held in Jakarta city on March 1, 2001. Subjects were the following seven: subjects on coal resource and technical strategy in the 21st century, challenge in coal development in Indonesia, geological structure survey at Tanjung Enim coal mine, waste water treatment in Indonesia, outlook for underground mining coal mines, joint research on the centralized monitoring system, and introduction of the optimum high wall coal mining system into open pit mining coal mines in Indonesia. The coal production amount in Indonesia was 75 million tons, and the domestic demand was 22 million tons. Japan imported 14 million tons from Indonesia. In coal mines in Indonesia, most of the coal preparation plants have no waste water treatment facilities. Considering that waste water treatment facilities are necessary for the plants in future, the joint research was made on the simple coal preparation waste water treatment system. (NEDO)

FY 2000 international exchange project on exchanges of engineers - Coal mine technology field. Overseas workshop (China); 2000 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya) kokusai koryu jigyo. Kaigai workshop (Chugoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of making technical exchanges with coal mine related engineers in China and surveying levels of coal production technology and the needs in China and possibilities of technology transfer from Japan, workshop was held and technical tours were made. On December 13, 2000, a workshop was held in China which was named 'Japan-China Joint Coal Project Workshop: Environment/Production/Security.' Participants were 112 including 16 from Japan and 96 from China. Subjects were as follows: subjects on coal resource and technical strategy in the 21st century, technical exchange project and technical development, Japan-China technical cooperation project, report on the operational situation of China Coal Industry Environmental Preservation Safety Training Center, Japan-China Joint Project on spontaneous combustion prevention technology, CMG recovery/utilization system joint demonstration project, Japan-China joint coal exploration project, Japan-China coal field geology joint exploration project, etc. (NEDO)

International exchange project for the engineer exchange project (in coal mine technology area) in fiscal 1998. Overseas workshop; 1998 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya) kokusai koryu jigyo. Kaigai workshop

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The international exchange project for the engineer exchange project (in coal mine technology area) in fiscal 1998, the 'Overseas workshop' has performed exchange in technologies with Australian coal mine engineers. The project refers to the Australian technological levels and needs in coal production, safety control and environment, as well as transfer of the Japanese coal mine technologies. This report summarizes the result of a survey on the engineer exchange project in the coal mine technology area and the possibility of joint researches. The 'overseas workshop' was held in November 1998 for two days in Brisbane City in QLD Province as the 'Japan-Australia coal technology workshop'. The 'Japan-Australia coal technology workshop' gave lectures in five sessions (the basic lecture, Japan-Australia high-speed excavation project, coal mine gas control project, exploration and resources, and development and experience of Japan). It also discussed two themes (mine safety management and rules, and greenhouse effect gases and coal mining). Two coal mines were visited thereafter to deepen the exchange with the Australian coal mine engineers. (NEDO)

Survey report of FY 1997 on the global environmental industry technology development promotion project. International research exchange project; 1997 nendo chosa hokokusho. Chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo (kokusai kenkyu koryu jigyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Exchange of personnel among foreign research organizations is significant for promoting research and development to create new research fields and to build new technological systems for the purpose of solving global environmental problems. For this purpose, researchers were sent/invited to/from international conferences and international symposiums related to global environmental technology and exchange of personnel with major foreign research organizations and universities was conducted under the cooperation of RITE and RITE-related researchers and related academic societies. Based on short-term invitation and sending of researchers as well as the feasibility study of researcher exchange, researchers were sent/invited on long- and mid-terms. As a result, exchange of personnel engaged in the latest research in Japan and overseas could be promoted. It was found that various researches are being conducted abroad in basic areas of global environmental technology. Since they are closely related to the research and development of industrial technology contributing to global environmental preservation promoted by RITE, it is important to establish a more efficient exchange system of researchers in the future. 91 refs., 38 figs., 14 tabs.

International exchange project for the engineer exchange project (in coal mine technology area) in fiscal 1998. Overseas workshop; 1998 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya) kokusai koryu jigyo. Kaigai workshop

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The international exchange project for the engineer exchange project (in coal mine technology area) in fiscal 1998, the 'Overseas workshop' has performed exchange in technologies with Australian coal mine engineers. The project refers to the Australian technological levels and needs in coal production, safety control and environment, as well as transfer of the Japanese coal mine technologies. This report summarizes the result of a survey on the engineer exchange project in the coal mine technology area and the possibility of joint researches. The 'overseas workshop' was held in November 1998 for two days in Brisbane City in QLD Province as the 'Japan-Australia coal technology workshop'. The 'Japan-Australia coal technology workshop' gave lectures in five sessions (the basic lecture, Japan-Australia high-speed excavation project, coal mine gas control project, exploration and resources, and development and experience of Japan). It also discussed two themes (mine safety management and rules, and greenhouse effect gases and coal mining). Two coal mines were visited thereafter to deepen the exchange with the Australian coal mine engineers. (NEDO)

Report for fiscal 2000 on joint seminar for coal engineer training project; 2000 nendo sekitan gijutsusha yosei jigyo godo semina hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-09-01

This paper summarizes the contents of the joint seminar for coal engineer training project in fiscal 2000, which has been held in Tokyo on September 25, 2000. The lectures included 'Coal Resources in Gunnedah Basin - Future Coal Supply Potential and Geophysical Exploration' by Ms. Julie Ann Moloney, senior geographical engineer at NSW Department of Mineral Resources, Australia, 'Human Resources Development for Coal Mining in Indonesia' by Mr. Bangun Usman Harahap at the Ministry of Mines and Energy in Indonesia, 'Queensland Rail, a strategic partner - linking Coal Producers to World Markets' by Mr. John Stuart Burrows at Coal Queensland Rail, Australia, and 'The export coal mines of western Canada - A review' by Mr. Ron Smyth, director BC Geological Survey Branch, Ministry of Energy and Mines, British Columbia, Canada. Questions and answers were exchanged actively for these lectures. (NEDO)

New energy vision of the Tono City area; 2001 nendo Tonoshi shin energy vision. Chiiki shin energy vision sakutei tou jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-02-01

As a leading plan to reconsider the resource consumption in large quantities and to change the society to a circulation type, a new energy vision of the Tono City area was worked out in Tono City, Iwate Prefecture. In this vision, FY 2002 was set as the first fiscal year, and FY 2010 as the target year. From the comprehensive judgement based on the objective availability, technical evaluation, civic needs, etc., biomass energy, wind energy, solar energy, etc. were made the main energy in new energy introduction. As model projects, studied were the introduction of solar energy utilization facilities to Kamigo Elementary School, introduction of the photovoltaic power generation to Aozasa Nursery School and disaster prevention base facilities, project on the wind power generation using large wind turbines, biomass alcohol plant, wood pellet production, etc. The target amount of new energy introduction was 2,640 kW in photovoltaic power generation, 19,000 kW in wind power generation, etc. The CO2 reduction amount including that in heat utilization, clean energy car, etc. was 41,374 t-CO2/y. (NEDO)

Report on the FY 1999 project for training coal engineers. Advanced course; 1999 nendo sekitan gijutsusha yosei jigyo hokokusho. Jokyusha course

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

This is a report on the training for coal technology which two Japanese engineers received in Australia. In Chapter 3 (Outline of Australia), they studied the national land, constitution of the national land, population, history, politics, economy and trade. In Chapter 4 (Coal geology), they read lecture data of university. In Chapter 5 (Outline of coal supply/demand), the coal export amount from Australia is 167 million tons. Steam coal of a little less than 50% is exported to Japan. In Chapter 6 (Coal mining technology), 100 million tons of NSW state and 100 million and 570 thousand tons of QLD state are mined by underground mining and open pit mining. Training was conducted on overburden/drilling/transportation of the open pit mining coal. As coal mining methods of underground mining, they learned the board and pillar coal mining and high wall mining as an extension of open pit mining. In Chapter 7 (Coal preparation), they observed/studied the jig, heavy media separator, heavy media cyclone separator, flotation equipment, spiral ore dressing equipment, fine powder centrifugal dewatering equipment, thickener, sieve, etc. They studied by data or by observation in Chapters 8 (Outline of coal mine), 9 (Outline of export port), 10 (Outline of railroad transportation), and 11 (Quality management). (NEDO)

Report on the 1997 Coal Engineer Training Program General Course Training; 1997 nendo sekitan gijutsusha yosei jigyo ippan course kenshu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-01

The paper reported training in the fiscal 1997 coal engineer training course. The training was made in a period from June 9 to November 12 in terms of actual training, English training, joint seminar, visits to the related facilities in Japan, overseas training, etc. for 10 engineers from mining companies, oil companies and electric power companies. In the actual training, the following lectures were given at International Resource University in Akita prefecture: coal exploration technology, coal situation of Australia, physical/chemical characteristics of coal and the application, coal preparation technology, coal situation in India, coal situation in the U.S., trend of general coal demand, coal situation in China, coal mining technology, actual surface mining technology, coal situation in Canada, commercial English, trend of raw coal demand, coal geology, environmental protection technology related to coal utilization, etc. Overseas training, which was divided into an Australia group and a Canada/America group, was conducted for about a month. Training in Indonesia was canceled because of a large scale forest fire which broke out immediately before the start. 88 figs., 52 tabs.

Report for fiscal 2000 on joint seminar for coal engineer training project; 2000 nendo sekitan gijutsusha yosei jigyo godo semina hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-09-01

This paper summarizes the contents of the joint seminar for coal engineer training project in fiscal 2000, which has been held in Tokyo on September 25, 2000. The lectures included 'Coal Resources in Gunnedah Basin - Future Coal Supply Potential and Geophysical Exploration' by Ms. Julie Ann Moloney, senior geographical engineer at NSW Department of Mineral Resources, Australia, 'Human Resources Development for Coal Mining in Indonesia' by Mr. Bangun Usman Harahap at the Ministry of Mines and Energy in Indonesia, 'Queensland Rail, a strategic partner - linking Coal Producers to World Markets' by Mr. John Stuart Burrows at Coal Queensland Rail, Australia, and 'The export coal mines of western Canada - A review' by Mr. Ron Smyth, director BC Geological Survey Branch, Ministry of Energy and Mines, British Columbia, Canada. Questions and answers were exchanged actively for these lectures. (NEDO)

Engineer exchanging project (coal mine technology field) in fiscal 1999. International information exchanging project (advance survey on Russia); 1999 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya) kokusai koryu jigyo. Jizen chosa (Roshia)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This advance survey on Russia has performed visiting surveys and information collection at coal related organizations inside Japan and in overseas countries on production technology levels, trends and technology exchange needs in overseas coal producing countries. The project is intended to serve for improvement in the contents of and smooth execution of the engineer exchange project in the 'coal mine technology field. It was carried out by expertise people as the site surveys and the engineer reception and exchange surveys. Because of the economic crisis that has hit Russia in 1998, unprofitable coal mines were closed one after another under the coal mine scrap and build policy under the initiative of the World Bank. This situation is giving serious impacts on coal mines in the Far East Russia and the coastal areas. However, the importance of coal as the primary energy source has not been changed at all in the Far East Russia. Thus, the areas have fallen into a situation that they must rely on a great amount of introduced and imported coals as a result of weakening in coal mines in the Far Eastern area on the other hand. This paper reports mainly the situation in which the coal industries in the coastal areas are placed, and the possibilities of technology exchange. (NEDO)

Fiscal 1999 survey report. Project of promoting international cooperation on global environments/Project of assessing climate change impacts; 1999 nendo chikyu kankyo kokusai kyoryoku suishin jigyo chosa hokokusho. Kiko hendo eikyo hyoka nado jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

As part of international cooperation concerning global warming, an assessment is conducted of climate change mitigating measures, from the viewpoints of technology, environment, economy, and community, in coordination with the IPCC (Intergovernmental Panel on Climate Change) 3rd working group responsible for energy policy and technological development. It aims to contribute to the preparation of a 3rd assessment report, and covers (1) the development of an assessment technique relating to cost analysis, (2) problems in the transfer of technology and solutions for them, and (3) the assessment of various policy options. Under item (1), studies are made about modelling techniques, common parameters and their values, potentials for effect, control of warming, etc. Under item (2), factors impeding the transfer and diffusion of technology are extracted and solutions therefor and the establishment of new incentives are deliberated, with analysis and investigation focused on tasks and solutions for furthering global transfer of technology with attention paid to various specific cases. Under item (3), concrete and feasible policy options are discussed on the basis of the outcome of the above-named endeavors, in view of characteristics of each of the regions, departments, and techniques. (NEDO)

Fiscal 1998 engineer interexchange project (coal mine technology field). Preliminary survey on the international interexchange project in America; 1998 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya) kokusai koryu jigyo. Jizen chosa (Beikoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

As a part of the fiscal 1998 international interexchange project in a coal mine technology field, the survey was made in America. Geological engineering problem has large effect on the protection and productivity of underground coal mines. Promotion of long wall mining has contributed to reduction of disasters, however, recently deaths due to roof collapse and wall collapse are on the increase. A roof evaluation technique was developed for adequate selection of mining methods and support design, and its standardization and diffusion are in promotion. Integration and improvement advanced in facility technology because of worldwide integration by acquisition of coal mine facility manufacturers. Introduction of high-power high-capacity facilities is increasing with introduction of large long wall working faces, and development of rear transport system technology and labor saving by remote control are also in promotion according to such trend. As automation and labor saving technology of mining facilities, the automated direction detection and control system by laser and gyroscope is under development. (NEDO)

Fiscal 1998 research report. Construction model project of the human sensory database; 1998 nendo ningen kankaku database kochiku model jigyo seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This report summarizes the fiscal 1998 research result on construction of the human sensory database. The human sensory database for evaluating working environment was constructed on the basis of the measurement result on human sensory data (stress and fatigue) of 400 examinees at fields (transport field, control room and office) and in a laboratory. By using the newly developed standard measurement protocol for evaluating summer clothing (shirt, slacks and underwear), the database composed of the evaluation experiment results and the comparative experiment results on human physiological and sensory data of aged and young people was constructed. The database is featured by easy retrieval of various information concerned corresponding to requirements of tasks and use purposes. For evaluating the mass data with large time variation read corresponding to use purposes for every scene, the data detection support technique was adopted paying attention to physical and psychological variable phases, and mind and body events. A meaning of reaction and a hint for necessary measures are showed for every phase and event. (NEDO)

Regional new energy vision formulation project for Takarabe Town. Report; 2001 nendo Takarabe cho chiiki shin energy vision sakutei tou jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-02-01

For promoting the introduction of new energy and for elevating people's consciousness of such in Takarabe Town, Kagoshima Prefecture, surveys and studies were conducted concerning the energy consumption profile of the town, the amount of new energy resources in existence, and new energy introduction plans, and then a vision was formulated. The town's energy consumption is estimated at 879.350-million MJ/year, with the transportation sector responsible for 46.6%, the industrial sector for 23.0%, the residential sector for 18.7%, and the people's livelihood-related business sector for 11.7%. Oil-based fuels occupy 70.4%, electric power 18.9%, and LP gas 8.4%. New energy introduction projects were studied, which included the introduction of photovoltaic power into the town office; photovoltaic power and hybrid power-lighted light for an oasis-on-the-road project and school facilities; introduction of cogeneration, wind power, and photovoltaic power into a hot spa health center and a water-friendly park; small-scale hydropower in the Okawara valley; wind power generation on Mount Shiraga and Jingaoka; introduction of clean energy vehicles for official use; and compost manufacturing and power generation using livestock waste. (NEDO)

Fiscal 1999 report on international joint research project on global environmental technology; 1999 nendo chikyu kankyo gijutsu kokusai kyodo kenkyu jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

As part of the above-named effort, Japanese researchers were dispatched to overseas universities and laboratories for implementing joint researches into 11 subjects selected by the NEDO (New Energy and Industrial Technology Development Organization) screening committee. When the feedback of fruits of the researches to NEDO projects is taken into account, it may be said that the accomplishments, attained relative to the development of processes for the practical application of environmentally-friendly biomass energy and measures for promoting its adoption, will contribute to the completion of an environmentally-friendly energy production process, excellent in CO2 emissions reduction, in which biomass will be the raw material. In relation to the technology of installing pipes for CO2 discharge into the ocean, some of the dispatched researchers had an opportunity of studying technological problems not deal with under NEDO research and development projects. In the study of organized structures of low-purity CO2 bubble groups, a great contribution was made to the promotion of the NEDO-implemented project of evaluating the impact of CO2 storage in the ocean upon environments. The development of remedial technologies for Microcystis aeruginosa-invaded lakes by introducing environmental engineering assumes a very important position in the endeavors for environmental improvement in developing nations in the Asia-Pacific region. (NEDO)

FY 1995 annual report on the project for promoting development of superhigh electronic techniques; 1995 nendo chosentan denshi gijutsu kaihatsu sokushin jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-05-01

Described herein are the FY 1995 results of the R and D project for developing superfine machining process techniques, measurement/analysis/controlling techniques for extreme conditions, and techniques for electronic materials of new functions, in order to establish the superhigh electronic techniques of two generations beyond. The project is implemented, mainly for the following targets: direct image drawing systems with electron beams by R and D of the techniques for electro-optical systems and superhigh-accuracy controlling techniques therefor; patterning systems with supershort-wavelength electro-magnetic waves by R and D of techniques for X-ray optical systems, superhigh-accuracy controlling techniques therefor and photosensitive process techniques; superfine photosensitive techniques with ultrashort-wavelength laser beams; techniques for superhigh-accuracy light-shielding systems; superhigh techniques for measurement/analysis/controlling of plasma reactions as the bases for plasma-aided superthin film making and superfine etching; basic techniques for superhigh cleaning; techniques for superhigh-sensitivity media; techniques for elements of new functions and making thin films thereof; and techniques for electronic materials of new functions. (NEDO)

Fiscal 1998 report on international joint research project for preventing global warming; 1998 nendo chikyu ondanka boshi kokusai kyodo kenkyu jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-12-01

Japanese researchers were dispatched to research institutes abroad for conducting joint studies on nine subjects for which such efforts would work effectively. The researchers were sent to various research institutes in the U.S., Britain, Germany, and others. The nine subjects were (1) the application of the most up-to-date welding and bonding technologies to liquid hydrogen storage/transportation containers, (2) development of low-temperature high-activity metal catalysts for energy conservation processes, (3) study of CO2 emission behavior using a large-scale simulator of deep sea circumstances, (4) study of condensation control for steam and chemical species in the global atmosphere, (5) numerical analysis of semiconductor crystal growth for ultralow loss power device, (6) development of sulfur-rich hydrocarbon gasification technology using a metal melting furnace, (7) assessment of techniques for evaluating origins of environmental pollution gas, geothermal gas, and soil gas using multiple isotopes, (8) analysis of behavior of the steam circulation type turbine system, and (9) the embodiment of a large premixed compression ignition engine. (NEDO)

Fiscal 1999 research cooperation project report. Research cooperation on coal liquefaction technology; 1999 nendo sekitan ekika gijutsu ni kansuru kenkyu kyoryoku jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This report summarizes the fiscal 1999 research cooperation project result on coal liquefaction technology. Cooperative FS was made on coal liquefaction technology of Indonesian coal as petroleum substituting energy. To obtain the basic data necessary for the FS, study was made on the applicability of Indonesian natural minerals as catalytic materials. Promising low-cost abundant Soroako Limonite ore showed a high catalytic activity for liquefaction reaction of Banko coal, and an excellent grindability. Improved BCL process including hydrogenation process was promising for production of high-quality coal liquid superior in storage stability with less nitrogen and sulfur contents. Survey was made on the general conditions of Tanjung Enim area including South Banko coal field concerned, and the geological features and coal seam of South Banko coal field which is composed of 3 seams including coal deposits of 6.35 hundred million tons. To study the marketability of coal liquid, survey was made on the current situation of oil, oil product standards, and blendability of coal liquid. Hydrogen for the liquefaction process can be obtained by coal gasification. (NEDO)

Coal engineer training project for fiscal 1999. Report on general course training; 1999 nendo sekitan gijutsusha yosei jigyo. Ippan course kenshu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-11-19

This report was made on the general course training in the coal engineer training project implemented in fiscal 1999. The training was conducted from June 7 through November 19 with total 7 participating trainees from an electric power company, mining company, etc.. In the training, the lectures were given by speakers from domestic coal related companies, universities, laboratories and the like at the University of International Resources, a foundation, for about three weeks. An English training was carried out by three instructors at the same University for about eleven weeks with the purpose of acquiring the linguistic ability required for overseas coal development. The joint seminar was conducted in Tokyo by inviting lecturers, two from Australia and one each from Canada and Indonesia. The training by visiting the domestic coal related companies was such that the overseas lecturers and trainees visited Matsushima Mining Co., the Electric Power Development Company, NKK Corp and others. The overseas study and training were performed on a 35 day schedule by visiting energy-related institutions, mining companies, railway companies, coal loading/unloading harbors, and thermal power stations in Canada, the U.S., and Australia. (NEDO)

Fiscal 1999 technical survey report. Basic project on international cooperation on energy consumption improvement, etc. (Japan International Cooperation Center project on promotion of exchange of specialists); 1999 nendo kokusai energy shohi koritsuka nado kyoryoku kiso jigyo / kokusai energy shohi koritsuka chosa nado kyoryoku kiso jigyo chosa hokokusho. Kokusai kyoryoku center jigyo suishin senmonka koryu sokushin jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-09-01

Specialist related to the governments of Thailand, Malaysia, and Indonesia where NEDO (New Energy and Industrial Technology Development Organization) implements its model projects were invited. They exchanged opinions with officials of the Japanese Government and affiliated organizations over measures for effective energy utilization. Opinions were also exchanged over the response of energy-consuming industries, development of technologies, and the status of their adoption. Activities of government-related participants are described below. Under a Model Project for Utilization of Waste Heat from Incineration of Industrial Waste at Industrial Estate, five Thai people with Industrial Estate of Thailand visited Ministry of International Trade and Industry, NEDO, NKK Corporation, Toyota Motor Corporation, and Keiyo Food Industrial Park. Under a model project on the recovery of waste heat from paper sludge incineration, four Malaysian people with Ministry of Energy, Communications and Multimedia or with Energy Center visited Ministry of International Trade and Industry, NEDO, NKK Corporation, Toyota Motor Corporation, and Japan Paperboard Industries Co., Ltd. Under a model project on the utilization of paper sludge and solid waste, four Indonesian people with Ministry of Industry and Trade or with Ministry of Mines and Energy visited Ministry of International Trade and Industry, NEDO, Babcock-Hitachi K.K., and Oji Paper Co., Ltd. (NEDO)

Fiscal 1996 survey report. `Ultra high electronic technology development promotion project` under consignment from NEDO; 1996 nendo kenkyu seika hokokusho. Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku jigyo `chosentan denshi gijutsu kaihatsu sokushin jigyo`

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-05-01

For the purpose of establishing ultra high technology of a next next generation level which is a basic technology in the electronic information field, a key to the realization of the high grade information society and a common technology base giving marked influences to the wide range industrial field, the R and D was started of ultra fine processing process technology, technologies on limit measuring/analysis/control and new functional electronic materials. Themes of the R and D are electronic beam direct picture drawing system technology, ultra short wavelength electromagnetic radiation patterning/system technology, ultra fine sensitizing technology to draw pictures on metal and crystal surfaces using ultra short wavelength laser beams, shading system technology of shading mask to be used to the process of drawing ultra high accuracy and complicated figures, ultra high tech plasma reactive measuring/analysis/control technologies which become the base of ultra thin films and ultra fine etching using plasma, ultra high tech cleaning base technology, ultra high sensitivity medium technology, new functional element/film formation technology, etc. 137 refs., 358 figs., 38 tabs.

Fiscal 1997 survey report. `Ultra high electronic technology development promotion project` under consignment from NEDO; 1997 nendo kenkyu seika hokokusho. Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku jigyo `Chosentan denshi gijutsu kaihatsu sokushin jigyo`

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-05-01

For the purpose of establishing ultra high technology of a next next generation level, the R and D was conducted of ultra fine processing process technology, technologies on limit measuring/analysis/control and new functional electronic materials. Themes of the R and D are electronic beam direct picture drawing system technology, ultra short wavelength electromagnetic radiation patterning/system technology, ultra fine sensitizing technology, ultra high accuracy shading system technology, ultra high tech plasma reactive measuring/analysis/control technology, ultra high tech cleaning basic technology, ultra high sensitivity medium technology, new functional element/film formation technology, etc. This R and D is a greatly influential basic research in the whole industrial field, and therefore, it is necessary that researchers standing foremost in each field of industry/university/government join the project and that various R and D infrastructures are made the most of. For this, the concentrated joint research method and the dispersed joint research method are combined, and the R and D is being conduced by equal partnership of each researcher. 421 refs., 823 figs., 91 tabs.

Preliminary survey report for fiscal 1999 on engineer exchange project (field of coal mining technology), international exchange project. Europe; 1999 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya) kokusai koryu jigyo jizen chosa. Oshu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

In Europe, international division is in progress as the result of market internationalization, and the coal market is experiencing an increasingly intensive competition in the storm of deregulation. The coal industry of Britain is away from a crisis for the time being, thanks to a new 5-year contract concluded with the electric utilities who are the primary purchasers, but it has to compete with imported coal and natural gas. The industry is also hit by the control imposed on the development of new opencast coal mines. Production is on the decline in the German coal market, which is one the largest in Western Europe, due to reduced subsidies, unfavorable geological conditions, lowered price, etc. The German coal industry is positively striving to exploit coal mines overseas and to export coal mining technologies. In Spain and France, the coal industry is forced to shrink and, in France, there is a plan to terminate coal mining completely in 2005. In Poland, the introduction of market economy has resulted in the influx of low-price coal from Russia etc., and all the Polish mines are now in the red. Its joining the European Union in the near future will further increase the pressure from other nations. It is learned that in Britain, Germany, etc., coal businesses are accelerating their transfer of technology to developing countries and are positively strengthening their presence abroad. (NEDO)

Report on achievement for fiscal 1998. Global environment industry technology development promotion project (the advanced technology survey and research project); 1998 nendo seika hokoiusho. Chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo (sentan gijutsu chosa kenkyu jigyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In order to structure innovative technologies to solve effectively the global environment problems, it is important to incorporate infra-structural technologies that have been achieved by universities and other research institutions. The fiscal 1998 project has commissioned 25 researches found superior from among research plans that have been invited during fiscal 1997. This paper enumerates the main themes including those under continued research. The research themes include: fixation of phosphor by using photo-energy, utilization of nitrogen fixing bacteria in rice plant roots for the purpose of carbon dioxide reduction, new functional solid ultra-strong acids for clean chemical processes, fixation of warming gases by using ultra critical fluid catalytic reactions, photo-catalysts having microporous structure, whose energy structure is controlled, waste water purification by using stimulation sensitive polymers, a practical and small high-speed environment purification system by means of a simple technology to cultivate high concentration bacteria of microorganisms, fundamental analysis of response to specific wavelength light in photosynthesized microorganisms, bio-remediation utilizing symbiotic systems of plants and bacteria, high efficiency catalysts purposed for total decomposition of water, and separation of carbon dioxide in deep sea bottoms by controlling hydrate crystal growth. (NEDO)

Engineer exchanging project on coal mine technology field in fiscal 1999. International information exchanging project (advance survey on North America); 1999 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya) kokusai koryu jigyo. Jizen chosa (Hokubei)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This project has been performed with an intention of making visiting surveys and information collection at coal related organizations in overseas coal producing countries on production technology levels and trends. The project is intended to serve for improvement in the contents of and smooth execution of the engineer exchange project in the 'coal mine technology field. It was carried out by the site surveys. The surveys revealed that the situation of the American coal industry is expected of stable increase in the demand and supply in the future, but the coal price is on the falling trend, and therefore, the industry is compelled to further increase the intensity and enhance the productivity. The industry is strongly influenced by the amended air pollution prevention act and nature destruction problems, hence further coal mine curtailment is estimated. Under such a background, it was found that the long-wall mining process progressing toward larger scale and higher productivity, and the high-wall mining process that provides higher productivity at lower cost and has less impact on the environmental problems can continue development in mountainous areas, particularly in the Appalachian area. The high-wall mining process mines coal at exposed facings on the side of a mountain by using a continuous miner, and transports the coal using machines. (NEDO)

International exchange project for the engineer exchange project (in coal mine technology area) in fiscal 1998. Pre-survey in Europe; 1998 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya) kokusai koryu jigyo. Jizen chosa (Oshu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This survey in Europe surveyed the current status of the coal industry, supporting directions and policies of governments on the coal industry, and summarized the information thereof. The survey included movements in policies and activities in transfer of technologies to overseas countries by governments and corporations of different countries, and the current status of the coal technology training project. The survey covered Britain and Germany. The British coal industry is facing a serious difficulty because the electric power industry being the major coal purchaser has changes its sourcing to natural gas. In addition, the open-cut mining which has been considered high in productivity has no further hope of big progress due to regulations in the environmental aspects. However, as a result of having performed positively research and development on production cost reduction, the production efficiency has grown excellently. Using this situation as the base, positive advancement into overseas countries is being carried out. The German coal industry has, in spite of having reduced the production size and the number of coal mines, shifted coal purchasers to electric power generation and steel making areas, and its quality and supply capability stand equivalent to those of imported coals. (NEDO)

Engineer exchanging project on coal mine technology field in fiscal 1999. International information exchanging project (the overseas workshop in Vietnam); 1999 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya) kokusai koryu jigyo. Kaigai workshop (Vietnam)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Technical information exchange was performed with Vietnamese engineers related to coal mine technologies through the overseas workshop and the technical tour. At the same time, investigations were executed on the production technology levels and needs in Vietnam, and on possibilities of transfer of Japanese technologies. The 'Overseas workshop (Vietnam)' was held on September 28, 1999 with the 'trends and problems in coal production technologies' as the main theme. Lectures were given in the session related to coal production technologies by Vietnamese coal technology experts, each from VINACOAL and IMSAT, and by two Japanese coal technology experts. A comprehensive discussion was also executed, and items of technical information were exchanged on the coal production technologies. The number of persons actually participated in the workshop counted 58, with the proceedings presented by them distributed. The Mao Khe and Duong Huy coal mines in Quang Ninh Province were visited as the technical tour, whereas the coal mine sites were inspected and opinions were exchanged with the site engineers. Gas analysis was performed in the Mao Khe mine from the viewpoint of a gas control technology, and site investigation was carried out on lock bolts in the Duong Huy mine from the viewpoint of a roof control technology. (NEDO)

Regional new energy vision formulation project for Yobuko Town. Fiscal 2001 report; 2001 nendo Yobuko cho chiiki shin energy vision sakutei jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-02-01

For promoting the introduction of new energy and for elevating people's consciousness of such at Yobuko Town, Saga Prefecture, surveys and studies were conducted involving the amount of energy needed by the town, the amount of new energy resources in existence, and new energy introduction programs, and a vision was formulated. The demand for energy of the town is estimated at 105,040 drums/year in terms of crude oil - 37% in electric power, 34% in fuel oil A, 13% in gas oil, and 8.1% in gasoline. As for the presence of new energy resources, it is deemed that wind and solar energies will be richly available. Studies were conducted for new energy introduction programs, which included the introduction of photovoltaic power into a nursing home for aged people, primary and junior high schools, and a water reservoir; street lamps lighted by a hybrid power system and a solar cell clock for the plaza in front of the harbor; introduction of wind power into the little islands of Ogawa and Kabe; installation of a solar energy collector for the nursing home for aged people; and the use of clean energy vehicles for official business. It is estimated that the efforts will bring about a 1,256.6 t-C reduction in carbon dioxide emissions. (NEDO)

Fiscal 2000 research achievement report. Super-advanced electronics technologies development promotion project; 2000 nendo kenkyu seika hokokusho. Cho sentan gijutsu kaihatsu sokushin jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-05-01

For the construction of a common base of key technologies in the domain of electronics and information with the influence propagating across a wide range of industries, research and development was conducted of technologies of ultrafine working process, technologies of ultimate measurement, analysis, and control, technologies of new functional electronic materials, etc. Studied in the field of electron beam lithography were high precision and large area imaging technology, highly accurate electron optics control system technology, and beam monitoring technology. Studied in the field of ultrashort wavelength electromagnetic wave patterning system technology were proximity ultrashort wavelength electromagnetic wave patterning system technology, reduced ultrashort wavelength electromagnetic wave patterning system technology, and ultrahigh precision new materials patterning technology. Also studied were technologies of super-advanced plasma measurement, analysis, and control, and technology of super-advanced cleaning. In the field of technologies of new functional elements and films, studies were conducted about technologies of highly sensitive GMR (giant magnetoresistive) film and head fabrication process for contact magnetic recording and technologies of a spin-valve head with submicron track width for contact magnetic recording. (NEDO)

Regional new energy vision formulation project for Kanai Town. Fiscal 2001 report; 2001 nendo Kanai machi chiiki shin energy vision sakutei tou jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

For promoting the introduction of new energy and for enhancing people's consciousness of such at Kanai Town, Niigata Prefecture, surveys and studies were conducted involving energy demand of the town, the amount of new energy resources in existence, and new energy introduction projects, and a vision was formulated. The town demands 541,062 GJ/year in energy, with the residential/commercial sector requiring approximately 46%, the industrial sector approximately 30%, and the transportation sector approximately 25%. The energy types are kerosene, heavy oils, gas oil, electric power, gasoline, and LPG, mentioned in the descending order in terms of magnitude of requirement. The resultant amount of carbon dioxide is estimated at 11,449 t-C. New energy introduction projects were discussed, which included photovoltaic power generation for primary and junior high schools, the town office, and the Dorin stock farm; a solar heat utilization system for the school meal center; wind power generation for Hometown Kimpoku, primary schools, and the Dorin stock farm; mini-scale hydroelectric power generation on the Shimpo river; use of forestry biomass (pellet stoves) at nursery schools; introduction of clean-energy automobiles for public use; and the introduction of cogeneration into Sado Hospital. (NEDO)

Fiscal 1999 technical survey report. Green Helmet Project (China, Sintering in steel industry); 1999 nendo green helmet jigyo (Chugoku seitetsugyo shoketsu) chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

A sinter cooler waste heat recovery system was installed and put to use at Taiyuan Iron and Steel Company in 1997. For the popularization of the system and technology, installation feasibility studies were conducted for Chungching Iron and Steel Company, Laiwu Iron and Steel, and Chiuchuan Iron and Steel Company. At Laiwu, studies were under way for the adoption of a China-manufactured system. At Chungching and Chiuchuan, there was a strong will to accept Japanese systems. Although a full investment/profit analysis including the cost of facilities remains to be carried out, it was concluded that the two steelmaking plants would be worth investment. The problems were how to raise funds and how much to invest. Although the system was simple and inexpensive under a Chinese design and was in a fairly wide use, it was found that it was not necessarily sufficient in heat recovering performance, service life, and capacity. A level of steam production to enable recovery in the form of electric power would be difficult to achieve, and the use of the resultant power would be limited only to in-house consumption of a small scale. (NEDO)

Fiscal 2000 report of investigation. Project for promoting international cooperation for global environment/Project for assessment on effect of climate change; 2000 nendo chikyu kankyo kokusai kyoryoku suishin jigyo / kiko hendo eikyo hyoka nado jigyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Assessment and examination were conducted on the scientific/technological aspect, environmental aspect and economic/social aspect concerning measures for mitigating climate change, as a part of international cooperation in global warming issues. In the development of assessment methods for cost analysis, it revealed that, in the activities for mitigating emission of greenhouse effect gases (GHG) or for increasing carbon sequestration, benefits of the mitigation sometimes surpassed their cost, allowing the society to benefit from the mitigation. In the examination of problems in technology transfer and their solutions, it was found that, in order to attain successful transfer, partnership among the parties interested was essential and that each government was capable of promoting such partnership. In the assessment of various policy options, the situation in the U.S. is such that the market aspect of GHG emission permit and credit trading is rather weak because of immaturity in a legal framework on GHG emission trading and because of undefinedness in the systems of the Kyoto Protocol and in the possibility of its validation. However, the reason enterprises are actively participating in the early market is that they plan a risk-hedge for example in anticipation of tighter regulations in the future. (NEDO)

Fiscal 1998 research report. Current state survey for promoting the field test project for introduction of advanced industrial furnaces; 1998 nendo koseino kogyoro donyu field test jigyo ni okeru jigyo sokushin no tame no jittai chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Survey was made on the current state of installation and operation of industrial furnaces mainly in manufacturers to predict the applicability of advanced industrial furnaces, and study was made on energy consumption trends, the energy saving effect of advanced industrial furnaces, and factor extraction for their applicability. In the survey, questionnaires were delivered to 4,597 offices extracted from domestic 50,780 offices with employees more than 30, and nearly 30% of them were recovered, covering nearly 2.6% of all the offices concerned with this survey. As the survey result, the total annual energy consumption of domestic manufacturers was estimated to be 740,949 x 10{sup 6}Mcal, and among it, 709,709 x 10{sup 6}Mcal for large industrial furnaces. Under the assumption that nearly 30% of large industrial furnaces in operation are replaced with advanced industrial furnaces, energy saving expectation is estimated to be 210,000 x 10{sup 6}Mcal. Opinions and demands for this project showed the difficulty in their application to industrial furnaces in operation and study on their effects. Further enlightenment activities are necessary. (NEDO)

Fiscal 1998 engineer interchange project on the engineer interchange project (coal mine technology field), international interchange project. Preliminary study in Russia; 1998 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya) kokusai koryu jigyo. Jizen chosa (Russia)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For the engineer interchange project (coal mine technology field), field survey for collecting information was made on the level and trend of production technology through visits to some coal industry organizations by specialists in Russia which is one candidate for the engineer training project by sending and receiving. Although coal is positioned as an important energy resource in Russia, poor business performance and a decrease in production are reported because of privatization and cur off of subsidies during a transfer period to a market economy. In addition, severe environment surrounding the Russian coal industry such as a delay of facility renewal due to poor funds, overage facilities, and moral reduction of workers due to a rationing delay has a potential for further reduction of production. The research group thus surveyed the current state of the Russian coal industry such as actual production structures, actual coal mines, technical levels, and various problem points in Moscow and Baykal districts. (NEDO)

Regional new energy vision for Soryo Town, Hiroshima Prefecture; 2001 nendo Soryo cho chiiki shin energy vision. Chiiki shin energy vision sakutei tou jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-02-01

A regional new energy vision was formulated for the town for 'contributing to the solution of environmental problems' and 'contributing to the reenergization of the regional community through utilizing resources in the region.' The final energy consumption of the town is 103,315 times 10{sup 3} MJ, with the transportation sector accounting for a percentage higher than the nation-wide average. The town is characterized in that it has but a small number of manufacturers, offices, or stores. As for new energy, it was estimated that 9117 times 10{sup 3} MJ/year would be gained by methanol produced from cultured weed, 5696 times 10{sup 3} MJ/year by medium/small-scale hydropower generation, 5,233 times 10{sup 3} MJ/year by photovoltaic power generation, and so forth. New energy introduction projects were discussed, which included medium/small-scale hydropower generation at a counter dam; the introduction of photovoltaic power into principal public facilities, general households, and agricultural facilities; introduction of solar heat appliances into principal public facilities and general households; introduction of clean energy automobiles into the town office and general households; and the introduction of pellet-fired stoves into principal public facilities and general households. (NEDO)

Report on the fiscal 1996 research cooperation promotion project, `the research cooperation diagnosis survey`; 1996 nendo kenkyu kyoryoku jigyo `kenkyu kyoryoku shindan chosa` hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

A diagnosis survey was conducted for Japan to cooperate in researching subjects on technical development in developing countries. In fiscal 1996, surveys were made on the following: (1) establishment of the industrial base (Vietnam), (2) preservation of biological diversification and the continuous utilization (Brazil), (3) fostering of the industry of automobile parts (Thailand), (4) finding out of items on environment related fields (India), (5) environmental response type system for effective use of water resource (the Philippines), (6) small size geothermal exploration in remote islands (Indonesia). (1) is research cooperation for welding technology, powder metallurgy technology, hypoid gear manufacturing technology, and iron making technology by the direct reduction method. In (2), research/development are conducted in cooperation with research institutes in Brazil on survey/identification/utilization of bioactive substances from biological resources in Brazil. In (4), an examination was made of the seeds for research cooperation in technical fields such as environment and energy. Having a strong relation with the industrial circle, SCIR is carrying out researches on aerospace, petrochemical, biology, electronics, medicines/drug, etc., which indicated fulfillment of intellectual infrastructure in India. 52 figs.

Preliminary reports on fiscal 2000 results of project for subsidizing international joint research; 2000 nendo kokusai kyodo kenkyu josei jigyo seika hokoku kai yokoshu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-12-01

This paper presents preliminary reports on fiscal 2000 results of project for subsidizing international joint research sponsored by NEDO. For international joint research teams doing excellent studies, their research expenses are subsidized, thereby promoting international research exchange, enhancing international level of industrial technology and contributing to the formation of basis for innovative industrial technology. The projects relating to the global environmental field are implemented jointly with RITE. The contents of the report to be published are, in the global environmental field (practicability study), development of oil substitute resources, reproducible resources, and technologies for producing polymeric and plastic materials benign to the earth by microorganism using carbon dioxide. In the substance/material field, the contents of the report are innovative production and device application of tunable photonic crystals using electronic penetration network; development of new synthesis process of innovative nitride, creation and theoretical calculation of electromagnetic function; studies on quantum transportation in superconductor and semiconductor bonding structures; and studies on quantum liquid and solid, and application to materials science and technology. (NEDO)

Regional new energy vision formulated for Murakami City; 2001 nendo Murakami shi chiiki shin energy vision sakutei tou jigyo. Murakami shi shin energy puran

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

For promoting the introduction of new energy and for enhancing people's consciousness of such at Murakami City, Niigata Prefecture, surveys and studies were conducted involving energy consumption in the town, the amount of new energy resources in existence, and new energy introduction projects, and a vision was formulated. The annual energy consumption of the city is estimated at 78,000 kL in terms of oil. The residential/commercial sector consumes 24,000 kL, the industrial sector 28,000 kL, and the transportation sector 26,000 kL, with the three sectors demanding similar amounts. The carbon dioxide emitted by the sectors is estimated at 223,000 t-CO2/year. New energy introduction projects were discussed, which included hot water supply, heating, road heating, and power generation, all these utilizing heat from the Senami hot spa; biogas fueled power generation and BDF (bio-diesel) bus operation in the Senami hot spa district; the introduction of a hybrid wind power/photovoltaic power generation system into Ogata Seaside Park; the introduction of a mini-scale hydroelectric power generation system into the Kamikaifu district; a large-scale wind power generation business at the Iwafune district; the introduction of wind power and photovoltaic power generation facilities into primary and junior high schools; the use of clean energy vehicles for official use; and so forth. (NEDO)

Fiscal 1997 survey report on international cooperation for the energy use rationalization method; 1997 nendo jigyo hokokusho (energy shiyo gorika shuho kokusai kyoryoku chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

To carry out LCA in ISO-14040, inventory analysis (IA) is the basic. For studying arrangement of public data to carry out IA, collection work was done of background data which are indirectly concerned with copying machine. First, methods to make inventory data (ID) which are thinkable in the present situation were prepared, and items of emitted matters to be collected were set up in relation to the impact assessment method. Secondly, scenarios of each stage of life cycle of copying machine were set up, and virtual data on the material/energy consumption amount were arranged. Based on this, a method was further studied for making ID of the parts used in electric power, iron/steel, plastics, and copying machine. Third, based on the above-mentioned study results, ID was actually made, and a possibility was studied of making inventory in life cycle of copying machine. Moreover, the state of the automobile LCA carried out at Stuttgart University was examined. At last, the paper summed up subjects of and future study methods for the inventory making method. 2 refs., 25 figs., 77 tabs.

Regional new energy vision formulation project for Ukiha Town. Fiscal 2001 report; 2001 nendo Ukiha machi chiiki shin energy vision sakutei tou jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-02-01

For promoting the introduction of new energy and for enhancing people's consciousness of such in Ukiha Town, Fukuoka Prefecture, surveys and studies were conducted involving the amount of energy needed by the town, the amount of new energy resources in existence, and new energy introduction projects, and a vision was formulated. The energy consumption of the town is estimated at 158,886 drums/year in terms of crude oil - 56.2% in electric power, 19.5% in gasoline, 10.5% in gas oil, 6.9% in kerosene, 4.2% in fuel oil A, and so forth. Projects for introducing new energies were studied, which included the introduction of photovoltaic power systems into public facilities, gymnastic halls, and comprehensive welfare centers; introduction of a large wind power system (1,500 kW) in the vicinity of the Michinoeki roadside service spot; installation of a power plant fueled by woody biomass (scrap wood, saw dust, and the like); introduction of clean energy vehicles for official use; installation of photovoltaic/wind hybrid power-lighted street lamps in the shopping area; installation of light traps for agriculture burned by photovoltaic power; and financial aids for encouraging the installation of photovoltaic power generation systems in general residences. (NEDO)

Summary of FY 1998 research and development activities. 19th R and D activity report; 1998 nendo gyomu gaiyo. Dai 19kai jigyo hokokukai

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

Summarized herein are the FY 1998 R and D activities by New Energy and Industrial Technology Development Organization (NEDO). The activities for new energy include those for the R and D for utilization of solar energy, commercialization of solar systems for industrial purposes, utilization of wind power, utilization of geothermal energy, utilization of coal energy, promotion of coal utilizing techniques, development of coal resources, development of fuel/storage techniques, development of techniques for hydrogen, alcohol and biomasses, promotion of new energy introduction, measures for international energy, surveys on development and introduction of new energy, and information services by NEDO's Information Center. The activities for industrial technology R and D include those for the R and D programs, medical/welfare-related equipment, industrial techniques for local environments, international industrial techniques, and establishment of research bases. Also summarized are the activities for coal mining structure adjustment, compensations for hazards resulting from coal mining, and alcohol production. (NEDO)

Fiscal 2000 coal engineer training program. Report on research study of general training course; 2000 nendo sekitan gijutsusha yosei jigyo. Ippan kosu kenshu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-11-22

In connection with fiscal 2000 coal engineer training program, a research study of the general course was implemented with eight participants for the period from June 12 to November 22. In the field training, lectures were given at International Resources University by speakers from related companies, universities and laboratories, on such subjects as coal geology, coal mining technology, coal probing technology, marine cargo transportation, analysis, coal utilization technology, environmental preservation technology, overseas coal mine development project, and foreign coal situations. Also, in the seminar, on-the-spot training was conducted at such places as Taiheiyo Tanko Kushiro mining station, Nippon Kokan KK Keihin ironworks, Electric Power Development Co., Isogo thermal power station, Idemitsu Kosan Co., coal laboratory, MITI Agency of Natural Resources and Energy. In the overseas training, research study in China was carried out during the period from July 2 to July 7 while research study in the U.S./Canada and Australia/Indonesia were conducted separately by two groups through 35 day trip from Oct 7 to November 10. The major places for visit were energy-related organizations, coal mining companies, railway companies, coal handling harbors, coal thermal power stations, coal analysis companies, etc.. (NEDO)

Report on an international joint research project for global environment technology in fiscal 1998; 1998 nendo chikyu kankyo gijutsu kokusai kyodo kenkyu jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In order to serve for measures against global problems taken by Japan, joint research was carried out with overseas research organizations. The research project selected ten themes considering urgency, internationality and economic proliferation effect in areas to serve for solution of global environment problems. These themes include removal or emission control of greenhouse effect gases, measures against atmospheric environment problems such as acid rains and ozone layer destruction, prevention of ocean contamination, development and effective utilization of energies and resources. When the feedback of these themes to the NEDO projects is considered, the research achievements in relation with development of the acid rain monitoring system in particular support indirectly development of carbon dioxide fixation technologies. The research achievements in developing an environmentally friendly biomass energy manufacturing process and environmental effect evaluation thereon contribute as an effective process to carbon dioxide reduction using biomass as raw materials. The achievements in research of nonlinear interfacial properties and mixed phase turbulence of low-purity carbon dioxide bubbles contribute to a project related to storage of carbon dioxide in oceans. (NEDO)

Summary of FY 1998 research and development activities. 19th R and D activity report; 1998 nendo gyomu gaiyo. Dai 19kai jigyo hokokukai

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

Summarized herein are the FY 1998 R and D activities by New Energy and Industrial Technology Development Organization (NEDO). The activities for new energy include those for the R and D for utilization of solar energy, commercialization of solar systems for industrial purposes, utilization of wind power, utilization of geothermal energy, utilization of coal energy, promotion of coal utilizing techniques, development of coal resources, development of fuel/storage techniques, development of techniques for hydrogen, alcohol and biomasses, promotion of new energy introduction, measures for international energy, surveys on development and introduction of new energy, and information services by NEDO's Information Center. The activities for industrial technology R and D include those for the R and D programs, medical/welfare-related equipment, industrial techniques for local environments, international industrial techniques, and establishment of research bases. Also summarized are the activities for coal mining structure adjustment, compensations for hazards resulting from coal mining, and alcohol production. (NEDO)

Report on the general course training of the fiscal 1996 coal engineer training program; 1996 nendo sekitan gijutsusha yosei jigyo ippan course kenshu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-12-01

The paper reported the general training of the fiscal 1996 coal engineer training program supported by NEDO. In Japan, where natural resource is poor, it is important to transfer from its petroleum dependence energy structure to the system for new energy development and dispersed energy supply. Coal resource is distributed widely in the world and is expected to spread in the future as a main substitute for petroleum. Worldwide attention is much paid to coal supply/demand and environmental problems, but the situation surrounding coal is not necessarily favorable. Under these conditions, Japan is a prominent coal importing country and is on the world-top level in terms of coal utilization technology. Japan has heavy responsibility and needs to play a leading role in adjusting and solving various problems on coal both domestically and internationally. Under the circumstances, 7 persons who are engaged in the coal related business and expected to be in future (3 from the mining relation and 4 from electric power comapanies) participated in the training this fiscal year and received the top-level training in Japan and overseas. 20 figs., 3 tabs.

Fiscal 2000 report on regional new energy vision formulation project for Yoron town; 2000 nendo Yoroncho chiiki shin energy vision sakutei nado jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-02-01

A regional new energy vision has been formulated for Yoron town, Kagoshima Prefecture, which will serve as guidelines for building an Environmentally Friendly Island. Yoron town is a town of approximately 6,000 inhabitants as of fiscal 2000, its energy consumption is equivalent to 61,427 drums in terms of crude oil, and it receives electric power from Yoron Power Plant of Kyushu Electric Power Co., Inc. The results of activities conducted in this connection are summarized in seven chapters, which are (1) coping with new energy vision formulation (2), energy supply and demand, (3) estimation of existing amount of new energy, (4) basic policy toward new energy introduction, (5) projects for introducing new energy, (6) existing energy systems, and (7) reference materials. Named as projects are the construction of a water supply power source (for storage pump) for the Furusato district; power source for farmland irrigation pumps; power sources for the integrated sports park and municipal library; power source for a farmyard compost center; wind power, photovoltaic power, and combined power generation facilities for streetlights; and the utilization of bagasse. (NEDO)

Fiscal 1998 research achievement report. Project for promoting development of super-advanced electronic technology; 1998 nendo chosentan denshi gijutsu kaihatsu sokushin jigyo seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

For the purpose of establishing super-advanced technologies two generations ahead in the field of electronics and information, research and development was carried out involving ultrafine machining process technology, technologies of ultimate measuring, analysis, and control, and technologies of electronic materials equipped with novel functions. In the study of writing systems in which writing is performed directly by an electron beam, writing technologies using electron beams under single-column and multi-column systems were taken up. In the study of ultrashort wavelength electromagnetic wave patterning systems, studies were made about equimultiple ultrashort wavelength and reduced ultrashort wavelength electromagnetic wave patterning. In the study of ultrahigh precision shielding systems, studies involved high precision in situ measurement and control of writing distortion, and ultrahigh precision and high current density electronic optical technologies. Also carried out were research and development of technologies of super-advanced plasma measurement, analysis, and control, technology of cleaning by ultrafine particle control, technology of ultrahigh sensitivity medium, and technologies of new functional elements and film fabrication. In the overall research and survey, surveys were conducted of the trends of development of technology of semiconductor related lithography. (NEDO)

FY 1998 annual report on the project of basic survey for improving energy consumption efficiency in developing countries and programs of international conferences including IPCC. Report on CDM workshop; Hatten tojokoku energy shohi koritsuka kiso chosa nado jigyo / IPCC nado kokusai kaigi jigyo (CDM workshop hokokusho) 1998 nendo jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

It is decided in the COP4 that the concrete schemes for the (Kyoto Mechanism) should be boiled down towards the end of 2000. Of the many outstanding issues concerned, those related to the clean development mechanism (CDM) involve a number of problems awaiting solution. In particular, setting the baselines for amounts of the greenhouse effect gas emissions in projects not existing, which are essential for identifying reduced amounts of emissions (or credits), poses serious difficulty because of wide arbitrariness involved in the methodology. Therefore, (standardization) of the procedures is demanded for the accurate identification. In actuality, however, no methodology has been established as to what methods will be possibly applicable to widely diversified types of projects. This workshop, therefore, has focused the discussions on the (baseline problems), expecting to serve as a trigger for the future directions by presenting international researches and promoting the discussions thereon to deepen recognition of these problems, where the AIJ experiences have served as one of the bases. (NEDO)

FY 2000 International energy use rationalization project. International technology dissemination project for improving energy consumption efficiency (Green helmet project for steel heating furnaces in Thailand); 2000 nendo kokusai energy shiyo gorika nado taisaku jigyo chosa hokokusho. Kokusai energy shohi koritsuka nado gijutsu fukyu jigyo (Green helmet jigyo (Tai: kozai kanetsuro))

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The project for energy saving dissemination activities and technological assistance for Thailand is carried out, and the FY 2000 results are reported. For Siam Iron and Steel (SISCO), the experts are dispatched for reviewing the operating conditions of the facilities constructed by the model project, their maintenance and examination, time series diagnosis of the recuperator performance, and providing technical assistance for fuel consumption and high-load combustion of the downstream unit. Furthermore, the site survey and technical assistance are provided for two newly selected Thai steel enterprises, Sahaviriya Steel Industries Public Co. (SSI) and the Bangkok Iron and Steel Works Co. (BISW). For SSI, it is predicted that energy of approximately 50Mcal/ton can be saved by, e.g., enhancement of waste heat recovery, enhancement of heat insulation of skid pipes, introduction of steel discharging temperature prediction system, and combustion control. For BISW, it is predicted that energy of approximately 25Mcal/ton can be saved by, e.g., enhancement of waste heat recovery and reduction of heat loss in the waste gas. (NEDO)

Report on the invitation program for developing countries concerning technology promotion project of global environmental industry in FY 1997; 1997 nendo chikyu kankyo sangyo gijutsu suishin jigyo ni kakawaru chikyu kankyo kanren gijutsu kaigai kenkyusha shohei jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In an effort to help preserve the global environment, International Center for Environmental Technology Transfer (ICETT) contributes to the solution of global environmental problems by promoting research exchanges with developing countries. As a part of this effort, ICETT hosted an environmental development researcher who visited Japan from the Institute of Environmental Research of Chulalongkorn University in Bangkok, Thailand. The invitation was extended at the request of NEDO. During the period of this investigation between September 16 and December 14, 1997, a photocatalyst was prepared and its performance was evaluated under the theme ``Application of photocatalysis to purification of atmospheric environment.`` At the same time, roadside test spots were inspected to study the practical application of optical photocatalysis. The visiting researcher also visited the National Institute for Resources and Environment to discuss with the staff of institute. This helped to deepen understandings of the state of air pollution problems confronting Japan, Europe, and North America, as well as issues related to the technologies that have been developed to solve these problems. The visiting researcher toured the RITE and examined Japan`s progress in the development of environmental control technology through joint research involving government, industry, and academia. At ICETT, the visiting researcher received training in Japan`s approaches to environmental problems in developing countries

Fiscal 2000 achievement report. Model project for international energy consumption efficiency improvement (Model project for improvement of boiler and turbine efficiency); 2000 nendo seika hokoku. Kokusai energy shohi koritsuka tou model jigyo (Boira tabin koritsu kojo model jigyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-12-01

A project was implemented for Japan to transfer its energy conservation technologies for helping Indonesia conserve energy and reduce CO2 emissions, which occurred at Muara Karang Thermal Power Plant of an Indonesian power company named PT PJB. Items to be introduced are condenser tubes (material change from cupro-nickel to titanium), ball cleaning equipment, turbine gland seal improvement, air preheater improvement, thermal efficiency management system, and so forth. In this fiscal year, turbine gland seals and air preheater elements were manufactured, and the thermal efficiency management system was designed. As an dissemination activity, 10 engineers were invited to Japan from the Indonesian Ministry of Energy and Mineral Resources, PT PLN, and PT PJB. They attended a training program lasting approximately two weeks, which included study tours to the factories actually building the equipment to be introduced and field/classroom training/education on thermal efficiency management and others. The engineers actively performed their boiler improvement work back in Indonesia. (NEDO)

Fiscal 1997 research report. International energy use rationalization project (Analytical tool research project for energy consumption efficiency improvement in Asia); 1997 nendo kokusai energy shiyo gorika taisaku jigyo chosa hokokusho. Asia energy shohi koritsuka bunseki tool chosa jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-05-01

The project aims to prepare inter-industry relations tables and models for energy analysis for Asian countries and thereby to probe into relations between the industrial structure or the ultimate consumption structure and energy consumption. For the comprehension of energy consumption as broken by each industry, Asian nations' inter-industry relations tables and energy statistics are linked for the compilation of energy analysis oriented inter-industry relations tables, and the resultant tables are used for the metric analysis of industrial structures and energy consumption structures in these countries. The tables prepared this time are 1985 tables for Korea, Indonesia, Thailand, and the Philippines and 1990 tables for China, Singapore, and Malaysia. The Malaysian transportation sector needs to be improved in energy saving. In Singapore, energy saving is functioning effectively in the transportation sector. China's energy consuming industries are those involving coal, chemistry, steelmaking, ceramics, and earth and quarrying. In Taiwan, improvement needs to be made in the transportation sector. Korea should conserve energy in the transportation sector. In the Philippines, energy needs to be saved in businesses related to water supply, transportation, and fishery. Thai industries as a whole needs to save energy. Improved energy consumption efficiency is sought for in the Indonesian cement related sector. (NEDO)

Fiscal 1997 research report. International energy use rationalization project (Analytical tool research project for energy consumption efficiency improvement in Asia); 1997 nendo kokusai energy shiyo gorika taisaku jigyo chosa hokokusho. Asia energy shohi koritsuka bunseki tool chosa jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-05-01

The project aims to prepare inter-industry relations tables and models for energy analysis for Asian countries and thereby to probe into relations between the industrial structure or the ultimate consumption structure and energy consumption. For the comprehension of energy consumption as broken by each industry, Asian nations' inter-industry relations tables and energy statistics are linked for the compilation of energy analysis oriented inter-industry relations tables, and the resultant tables are used for the metric analysis of industrial structures and energy consumption structures in these countries. The tables prepared this time are 1985 tables for Korea, Indonesia, Thailand, and the Philippines and 1990 tables for China, Singapore, and Malaysia. The Malaysian transportation sector needs to be improved in energy saving. In Singapore, energy saving is functioning effectively in the transportation sector. China's energy consuming industries are those involving coal, chemistry, steelmaking, ceramics, and earth and quarrying. In Taiwan, improvement needs to be made in the transportation sector. Korea should conserve energy in the transportation sector. In the Philippines, energy needs to be saved in businesses related to water supply, transportation, and fishery. Thai industries as a whole needs to save energy. Improved energy consumption efficiency is sought for in the Indonesian cement related sector. (NEDO)

Survey report for fiscal 1993 on basic survey project for energy consumption efficiency improvement in developing countries. Database development project 5 (The Philippines); 1993 nendo hatten tojokoku energy shohi koritsuka kiso chosa jigyo (database kochiku jigyo). 5. Philippines

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

Volume 5 covers the Philippines. The database development project has two goals. One is to collect basic data for joint projects for preparing energy conservation master plans for China and Indonesia, and the other is to build a comprehensive database for 8 countries including the said 2 countries (China, Indonesia, the Philippines, Thailand, Malaysia, Korea, Taiwan, and Japan) for contribution to the enhancement of energy conservation in the region involved. This Volume 5, dealing with 5 countries out of the 8 excluding China, Indonesia, and Japan, accommodates data on the Philippines, with whom a data collecting contract has just been signed in this fiscal year, which cannot be appropriately accommodated in Volume 1. The data referred to just above include the progress marked in this fiscal year in the preparation for the collection of actual data about energy consumption in Filipino factories scheduled to be carried out in and after the next fiscal year. (NEDO)

Fiscal 2001 photovoltaic power generation field test project (Locations of systems installed in fiscal 1998-2000 at public facilities and industries); 2001 nendo taiyoko field test jigyo (Kokyo shisetsuyou sangyo tou you 1998 - 2000 nendo secchisha)

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-05-01

The test was conducted for systems installed at General Health and Welfare Center, Munakata City, Fukuoka Prefecture; Comprehensive Traffic Center, Yamaguchi Prefecture; Primary schools, Sendai City, Miyagi Prefecture; Sakuragi Children's House, Shizuoka Prefecture; Midorigaoka Primary School, Hyogo Prefecture; Heath Center, Minamata City, Kumamoto Prefecture; Science Museum for Young People, Yamaguchi Prefecture; Wakatsuki Plastic Surgery Hospital, Niigata Prefecture; Hokuto Corporation, Aichi Prefecture; Industrial Research Institute, Ishikawa Prefecture; Shonan Institute of Technology, Kanagawa Prefecture; Gyosen Oil Co., Tokyo; Tamana Senior High School, Kumamoto Prefecture; Yukiyoshi Clinic, Niigata Prefecture; Saishoen Social Welfare Corporation; Akishimadai Kindergarten; Azabu Veterinarian School Group; Ueki-Kita Junior High School, Ueki Town; Garden of Longevity, Isen Town; Takamatsu Primary School, Takamatsu Town; Himeji Red Cross Hospital; and Kita-Daito Island Branch, Okinawa Electric Power Company, Inc. Mentioned in this report are the outlines of the photovoltaic power generation field test, the results of joint research, expected technical effect, enlightening effect, troubles involving power generation systems, and so forth. (NEDO)

FY 2000 report on the research cooperation project on the research cooperative follow-up for development of the manufacturing technology supported by advanced and integrated information system through cooperation; 2000 nendo kenkyu kyoryoku jigyo. 2000 nendo kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku follow up jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The manufacturing technology supported by advanced and integrated information system through cooperation (MATIC), that is, a project supporting the production technology including the international information system and CAD/CAM system, etc. was carried out from FY 1994 to FY 1998. From FY 1999, the follow-up project is being implemented for the spread of the MATIC results, support for the independent R and D and the technical guidance. China, Indonesia, Malaysia and Singapore participated in this project, by which the support and technical guidance were given in three fields: automobiles/the parts; household electric appliances/the parts; fiber/apparel. At present, each country is continuing its own activity for using the system developed in the MATIC project in its country. In this fiscal year, researchers were sent to each country for supporting the activities. Further, the MATIC follow-up committee was established to conduct the drawing-up of a business plan, grasp of the state of the spread/R and D, discussion about problems/subjects, comprehensive evaluation of the MATIC project, etc. (NEDO)

FY 2000 report on the research cooperation project on the research cooperative follow-up for development of the manufacturing technology supported by advanced and integrated information system through cooperation; 2000 nendo kenkyu kyoryoku jigyo. 2000 nendo kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku follow up jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The manufacturing technology supported by advanced and integrated information system through cooperation (MATIC), that is, a project supporting the production technology including the international information system and CAD/CAM system, etc. was carried out from FY 1994 to FY 1998. From FY 1999, the follow-up project is being implemented for the spread of the MATIC results, support for the independent R and D and the technical guidance. China, Indonesia, Malaysia and Singapore participated in this project, by which the support and technical guidance were given in three fields: automobiles/the parts; household electric appliances/the parts; fiber/apparel. At present, each country is continuing its own activity for using the system developed in the MATIC project in its country. In this fiscal year, researchers were sent to each country for supporting the activities. Further, the MATIC follow-up committee was established to conduct the drawing-up of a business plan, grasp of the state of the spread/R and D, discussion about problems/subjects, comprehensive evaluation of the MATIC project, etc. (NEDO)

International measures project for rational energy use (Survey project of the analysis tool of Asian energy consumption efficiency). List of errata; 1998 nendo kokusai energy shiyo gorika nado taisaku jigyo seigohyo. Asia energy shohi koritsuka bunseki tool chosa jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The list of errata was prepared for the data book of the international measures project for rational energy use (Survey project of the analysis tool of Asian energy consumption efficiency). Corrected pages of the data book 1 (1990) are as follows: 187-190, 223-226, 259-262, 295- 298, 369-370, 387-388 and 405-406 on Malaysian data. Corrected pages of the data book 2 (1985) are as follows: 102-105 on Chinese data, 154 on common data, and 187-190, 223-226, 259-262, 295-298, 369-370, 387-388 and 405-406 on Malaysian data. (NEDO)

Fiscal 2000 comprehensive survey. Project for development of international standards for supporting novel industries; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo. Sogo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development for creation of international standards had been under way for three years since fiscal 1998 for the sustenance and securement of Japan's technical advantage and for the enhancement of the international competitiveness of its industries. In the ultimate fiscal year for the project, studies were made for establishing standards relative to 13 subjects, involving the management of color reproduction, assurance of interoperability of optical disk systems, digital image processing for home-use digital electronic appliances, securement of connection between information devices for home-use electric appliances, production process system, method for testing and evaluating fine ceramics for communication equipment, method for evaluating high-temperature properties of new glass, method for testing and evaluating corrosion resistance of surface treated steel sheets, method for testing and evaluating pure titanium, method for testing and evaluating plastic optical fiber, method for evaluating properties of high-strength large-diameter steel pipe for ultrahigh-pressure natural gas pipeline, method for measuring fuel consumption of hybrid electric vehicles, method for calculating the recycling rate of automotive products, or the like. The fruits of 77% of the efforts have already been proposed as international standards or have arrived at a stage where they may be proposed as such. (NEDO)

Fiscal 2000 comprehensive survey. Project for development of international standards for supporting novel industries; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo. Sogo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development for creation of international standards had been under way for three years since fiscal 1998 for the sustenance and securement of Japan's technical advantage and for the enhancement of the international competitiveness of its industries. In the ultimate fiscal year for the project, studies were made for establishing standards relative to 13 subjects, involving the management of color reproduction, assurance of interoperability of optical disk systems, digital image processing for home-use digital electronic appliances, securement of connection between information devices for home-use electric appliances, production process system, method for testing and evaluating fine ceramics for communication equipment, method for evaluating high-temperature properties of new glass, method for testing and evaluating corrosion resistance of surface treated steel sheets, method for testing and evaluating pure titanium, method for testing and evaluating plastic optical fiber, method for evaluating properties of high-strength large-diameter steel pipe for ultrahigh-pressure natural gas pipeline, method for measuring fuel consumption of hybrid electric vehicles, method for calculating the recycling rate of automotive products, or the like. The fruits of 77% of the efforts have already been proposed as international standards or have arrived at a stage where they may be proposed as such. (NEDO)

Regional new energy vision formulation for Kadogawa Town, Miyazaki Prefecture. Report; 2001 nendo Miyagi ken Kadokawa cho chiiki shin energy vision sakutei tou jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-02-01

For promoting the introduction of new energy and for elevating people's consciousness of such in Kadogawa Town, Miyazaki Prefecture, surveys and studies were conducted concerning the energy demand in the town, the amount of new energy resources in existence, and new energy introduction plans, and then a vision was formulated. The town's energy demand is estimated to be 1,197.4-million MJ/year, which includes 44.1% for the transportation sector, 22.9 for the residential sector, 22.7% for the industrial sector, and 10.3% for the people's livelihood-related business sector. The energy demand is covered 62.7% by oil-based fuels, 22.7% by electric power, and 13.4% by LP gas. Projects discussed for new energy introduction included the introduction of photovoltaic power into the town office, primary schools, and a comprehensive workers' welfare center; introduction of a solar hot water supply system and hybrid power-lighted street light into a seaside park; introduction wind power into Motoyama Park; mini-scale hydroelectric power on the Isuzu river; introduction of clean energy vehicles into the town office; power generation fueled by methane gas from livestock excrement; and introduction of natural gas fueled cogeneration into a resort house. (NEDO)

FY 1998 report on the results of the project on the next generation structure housing development; 1998 nendo jisedai kozo jutaku kaihatsu jigyo seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The purpose of this project is to develop/verify technology to design/construct a structural body of multiple dwelling house which is highly durable and usable at maximum of the limited space with no projections of poles/beams, and is also to develop/verify a composite system of a structure and each house in which residential space can freely be changed horizontally/vertically in response to the leveling-up of living and changes in life style. The following were conducted: construction of an experimental house group with next generation structure; development of technology of effective space utilization/high durability body construction; development of technology of structural analysis/design systematization of antiseismic/damping system; development of commercialization of technology to heighten frame durability, development of technology to heighten durability of finishing materials of a body; development of low cost construction technology; development of technology of interface between a body and each house; verification of housing performance using a next generation body system; generalization of next generation frame system/house system. To reflect the results of the research quickly, the details of the research are systematized, and a draft is worked out of a guide for constructing the next generation frame system/house system which were arranged between the current architecture related laws and business as a general multiple dwelling house. (NEDO)

Report on the fiscal 1995 research cooperation promotion project, `the research cooperation diagnosis survey`; 1995 nendo kenkyu kyoryoku suishin jigyo `kenkyu kyoryoku shindan chosa` hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

A diagnosis survey was conducted for Japan to cooperate in researching subjects on technical development in developing countries. In fiscal 1995, surveys were made on the following: (1) recycling technology of biomass industrial waste in the tropical region, (2) small size geothermal exploration in remote islands, (3) waste water recycling system using activated carbon, etc., (4) upgrading of proofreading technology of measuring standards, (5) technology to simply set up conditions for forming engineering plastics, (6) assessment of safety of chemical substances. In (1), energy and useful matters are recovered from oil palm of Indonesia by thermal decomposition technology. In (2), a system is constructed which can effectively explore geothermal energy in remote islands in the east Indonesia. As to (3), a survey is conducted in the Philippines. (4) contributes to upgrading of length measuring standards in Thailand. (5) attempts to improve technology of forming engineering plastics. In (6), research cooperation is made for preventing environmental pollution and health damage by chemical substances from happening in Thailand and for technology for assessing safety of chemical substances which contributes to the proper use of the hazardous material law in Thailand. 28 figs.

FY 2000 research cooperation project on the support for heightening of capability of research institutes; 2000 nendo kenkyu kyoryoku jigyo. Kenkyu kikan noryoku kojo shien

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of supporting the heightening of capability of research institutes in the following 7 countries, China, Thailand, Malaysia, Indonesia, the Philippines, India and Vietnam, exchanges/guidance/training were conducted by sending researchers from Japan and inviting researchers to Japan. Japanese researchers were sent for the following: cleaner technology in fiber dyeing finish (Thailand), 3 cases including the survey of the actual state of underground water pollution caused by harmful pharmaceuticals (the Philippines), 2 cases including the energy recovery in the fiber dyeing industry (Indonesia), making of energy management rules in the industrial field (Malaysia), spread of the photovoltaic power generation to areas where there is no electricity service in Tibet (China), 3 cases including the personnel development in the environmental management field of electric power companies (India), and 2 cases including the information exchange program in the energy conservation field (Vietnam). A total of 74 researchers were invited to Japan, that is, to the environmental protection training course of Japan. (NEDO)

Report for fiscal 1998 on the international joint research project of medical welfare equipment; Iryo fukushi kiki kokusai kyodo kenkyu jigyo 1998 nendo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In connection with the international joint research project of medical welfare, a report was made on the results of the investigation conducted in 1998 concerning the technology of overseas medical welfare equipment. In the investigation of china, observation was made on the actual state of the representative medial institutions, with opinions exchanged. Obsolete equipment and old technology are the present state in China, which is strongly desirous of exchanging information with Japan. In Taiwan, being full of venture spirit, an ultrasonic thermal treatment apparatus and an ultrasonic echo device have been produced for example. In Europe, an observation tour was conducted on a German manipulator and process robot while an investigative visit and exchange of opinions were made on the living environment and facilities in Italian training center for physically handicapped persons. Japan's self-supporting and assisting system for excretion attracted many questions and comments. In the investigation in the U.S., views were exchanged concerning '{sup 13}C-MRS device for non-invasion brain metabolic measurement' in research institutions such as universities. A machine developed in Japan received a high evaluation in that {sup 13}C spectrum was obtained from a substantial depth. (NEDO)

Fiscal 2000 international energy use rationalization measures project. International energy consumption efficiency improvement technology diffusion project - Green helmet project (Thailand: Report on heating furnace energy conservation seminar); 2000 nendo. Kokusai energy shiyo gorika to taisaku jigyo, Kokusai energy shohi koritsuka to gijutsu fukyu jigyo, Green helmet jigyo (Thai : kanetsuro shoenergy seminar hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The above-named seminar was held in Bangkok, Thailand, on January 30, 2001, and covered three kinds of industries of ceramics, glass, and aluminum. Approximately 200 people attended the meeting, consisting of NEDO (New Energy and Industrial Technology Development Organization)-affiliated people and 16 lecturers from Japan, and Thai participants. The seminar comprised a 'keynote address' and 'lectures on engineering' that aimed at the three industries as a whole, and 'lectures on engineering' and 'cases and activities for energy conservation' that aimed, respectively, at the three industries. Lectures were delivered on operating technologies which were already in practical use and on state-of-the-art technologies. The keynote address, entitled 'Global warming prevention and industrial furnaces,' covered the results of the 'High-performance industrial furnace field test project.' The lectures on engineering dealt with the 'instrumentation control system' and 'heat insulation technology' which were basic technologies for energy conservation and 'diagnosis technology and practice' which aimed at the enhancement of energy conservation after the start of operation. Questions and answers were earnestly exchanged. (NEDO)

Project for rationalization measures for international energy conservation. Model project concerning efficient consumption of energy for international energy conservation (Model project of waste heat recovery on billet reheating furnace); 1999 nendo kokusai energy shiyo gorika nado taisaku jigyo seika hokokusho. Kokusai energy shohi koritsuka nado model jigyo (kozai kanetsuro hainetsu kaishu model jigyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of curtailing energy consumption in the steel industry, a heavy energy consuming industry in Thailand, a model project was carried out for waste heat recovery on a billet reheating furnace, with the fiscal 1999 results compiled. This model project is to install a high efficiency recuperator and the latest combustion control system in the existing furnace in a SISCO (The Siam Iron and Steel Co., Ltd.) plant in Thailand. This year, following the preceding year, the construction manual was prepared, as were the test run manual, performance verification manual, operation and maintenance manual, etc. Supervisors were also dispatched to the site, giving guidance of the installation work, test run and the demonstrative operation, on the basis of these documents. Operation for verifying performance of the equipment was implemented on November 17, 1999, with the intended results obtained. Subsequently, operation maintenance instructors were dispatched, with energy saving effect proved through the collection/analysis of operation data and monitoring, for example. Further, as the dissemination activities, pamphlets and videos were prepared, and seminars were held, among others. (NEDO)

Fiscal 1998 research report. International measures project for rational energy use (Survey project of the analysis tool of Asian energy consumption efficiency); 1998 nendo chosa hokokusho. Kokusai energy shiyo gorika nado taisaku jigyo (Asia energy shohi koritsuka bunseki tool chosa jigyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-02-01

This project aims to prepare the inter-industry relations table and analysis model for energy analysis for every Asian country, and analyze the relation between energy consumption and industrial structure or final demand structure. The 1985 and 1990 inter-industry relations tables of each country were prepared in cooperation with the governmental organizations of China, Korea, Taiwan, Philippines, Thailand, Malaysia, Singapore and India. However, the 1987 and 1990 tables were prepared for China. In fiscal 1998, the project invited the representatives of each concerned organization, and held the international workshop together with Japanese specialists to discuss various issues related to not only table preparation but also data analysis. The following items were analyzed for every country: a change in final energy consumption, a dependence on coal in primary energy consumption, transfer of energy consumption to other energy resources, and an energy consumption rate in the whole industry. (NEDO)

Research report of FY 1997 on the environmentally acceptable coal utilization system introduction support project. Demonstration project on simplified desulfurizers; 1997 nendo seika hokokusho. Kankyo chowagata sekitan riyo system donyu shien jigyo (kan`i datsuryu setsubi ni kakawaru jissho jigyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

To reduce SOx with coal utilization, a desulfurizer is introduced in Thailand as diffusion activities in the demonstration program. The purpose is to reduce the environmental pollutants. For this desulfurizer, lime mud mainly composed of lime stone is used as an absorber. SO2 in the flue gas is absorbed by the slurry of lime mud, to form calcium sulfite. The calcium sulfite blown in the bottom of recycling tank is oxidized by oxygen in the air, to form gypsum. The gypsum is recovered as a by-product. In this fiscal year, a feeder of lime stone, spray nozzles, and various analysis apparatuses were supplied. Supervisors for electric instrumentation/control were also dispatched as well as for main body construction, to carry out the instrumentation setting works, check of sequences, and adjustment of apparatuses. After the test operation, supervisors for the demonstration operation were dispatched up to March 1998, to conduct the cooperation works between Japan and Thailand sides. Thus, successful and successive demonstration operation was confirmed. 21 figs., 6 tabs.

Fiscal 1997 research report. International energy use rationalization project (Analytical tool research project for energy consumption efficiency improvement in Asia); 1997 nendo kokusai energy shiyo gorika nado taisaku jigyo chosa hokokusho. Asia energy shohi koritsuka bunseki tool chosa jigyo (honpen)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-05-01

Efforts have been under way to prepare inter-industry relations tables and energy data for four Asian countries, namely, China, Taiwan, Singapore and Malaysia, and a tool for energy consumption efficiency analysis has been developed and improved. In Chapter 1, energy supply and demand in the above-named four countries is reviewed on the basis of recent economic situations in these countries. In Chapter 2, bilateral inter-industry relations tables usable under the project are employed for the analysis of the economic status of each of the countries and energy transactions between them, and a method is described of converting the tables into one-nation inter-industry relations tables which meet the need of this project. In Chapter 3, national characteristics reflected on the respective energy input tables are described, and a method is shown of converting a nationally characterized unit energy table into a common unit energy input table for registration with a database. In Chapter 4, the constitution of the Asian energy consumption efficiency improvement analyzing tool and a system using the tool are explained. In Chapter 5, some examples of analyses conducted by use of the analyzing tool are shown, in which the energy saving effect and CO2 emission reduction effect are estimated for Indonesia by use of the analyzing tool. (NEDO)

Fiscal 1999 report on results of joint demonstrative project for environmentally benign coal utilization system. Demonstrative project concerning coal preparation technology (China); 1999 nendo kankyo chowagata sekitan riyo system kyodo jissho jigyo seika hokokusho. Sentan gijutsu ni kakawaru jissho jigyo (Chugoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This paper describes the demonstrative project for coal preparation technology, as a part of the measures against environmental pollution due to the structuring of demonstration and dissemination basis for clean coal technologies in China, The results for fiscal 1999 is reported. In the utilization of coal in China, a problem of urgency is the highly efficient selection and removal of sulfur contents in raw coal. Coal production in Chongquing City is yearly 30 million tons, of which 90% contains sulfur contents of 3% or higher. At Jinjia Colliery of Panjiang Coal and Electric Co. Ltd., Guizhou Province, a site for the present project, a number of coal seams are unsuitable for single utilization because of high sulfur contents. The coal preparation technologies to be introduced are expected to improve coal preparation efficiency and desulfurization ratio in terms of both the washability of raw coal and the accuracy of the coal washer. This is the third year of the project, with the following activities performed, namely, research/design, manufacturing/procurement of equipment, design for construction work, training of operators or the like, and documentation. The manufacturing and procurement are for such equipment as vacuum disk filter with accessories, waste water thickener, pressure filter for tailings with accessories, flocculant pump/piping, slurry tank/pump, high-shear mixer with accessories, and electric instrumentation. All the equipment arrived at the site in January, 2001. (NEDO)

Report on the project on working out the new energy vision of Hisai City; 2001 nendo Hisai shi chiiki shin energy vision sakutei tou jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

For the purpose of promoting the introduction of new energy and enhancing the awareness of it in Hisai City, Mie Prefecture, an investigational study was conducted of the energy demand structure, existence amount of new energy and project for new energy introduction, and a vision was worked out. The energy consumption amount of the city was 21,500 lorries in the industrial sector, 11,200 lorries in the transportation sector, 2,700 lorries in the business sector and 2,400 lorries in the residential sector in terms of tank-lorry loaded oil. As features, the following were cited: growth in the transportation sector, mostly in automobiles, was great; growth in the electric power consumption in the residential sector was great. As the project for new energy introduction, the following were supposed and studied in terms of the economical efficiency and environmental acceptability: introduction of cogeneration to hospital; introduction of ligneous biomass power generation to hospital; substitution of wood burning boiler for A heavy oil boiler for hot water supply use; introduction of photovoltaic power generation for home use and business use; introduction of solar heat use hot water supply device. (NEDO)

Fiscal 1999 report on result of the model project for waste heat recovery in hot blast stove; 1999 nendo netsufuro hainetsu kaishu model jigyo seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

For the purpose of curtailing energy consumption of the steel industry, a heavy energy consuming industry in China, a model project was carried out for waste heat recovery in a hot blast stove, with the fiscal 1999 results reported. In the process of this project, a heat exchanger for recovering heat is installed in the exhaust gas flue of a hot blast stove in ironworks, with sensible heat recovered through a heating medium. The heat exchanger for recovering heat and the preheating heat exchanger, which was installed in the main pipe for blast furnace gas and for combustion air, were connected by pressure piping, with the blast furnace gas and the combustion air preheated. In addition, a heating medium circulating pump for transporting the heating medium is installed, as are an expansion tank for absorbing expansion/contraction due to change in temperature, a heating medium storage tank for accepting the entire heating medium in the system for the maintenance of the equipment, and heating medium feeding pump, for example. This year, on the basis of the 'Agreement Annex', basic designs and detailed designs were performed for each equipment in the waste heat recovering equipment for the hot blast stove. Further, procurement and manufacturing were implemented for various component parts and devices of the waste heat recovering equipment. (NEDO)

FY 2001 report on the project on working out the new energy vision of Takasu Village; 2001 nendo Takasu mura shin energy vision sakutei tou jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

For the purpose of promoting the introduction of new energy and enhancing the awareness of it in Takasu Village, Gifu Prefecture, an investigational study was conducted of the energy consumption amount, existence amount of new energy and project for new energy introduction, and a vision was worked out. The energy consumption amount of the village was 632,805.8 GJ/y. The rate of energy source was 23.2% of electric power, 22.2% of heavy oil, 21.2% of light oil, 20.8% of kerosene, 11.1% of gasoline and 1.6% of LPG. As viewed by sector, the energy consumption amount consisted of 42.1% in the transportation sector, 25.3% in the business sector, 20.2 in the industrial sector and 12.4% in the residential sector. As the project for new energy introduction, the following were studied: introduction of photovoltaic power generation to village center; introduction of photovoltaic /micro wind hybrid power generation to street light/burglar light/disaster-prevention use emergency power source at tourist resort 'Hirugano Heights'; introduction of biogas power generation by methane fermentation using animal feces, garbage, etc. as raw materials; utilization of ice/snow energy for storage of bulbs of flower/ornamental plant and as supply of cold wind to milk cow. (NEDO)

Survey report for fiscal 1999. Project of diffusing gas driven cooling systems in Oman; 1999 nendo Oman koku ni okeru gas reibo fukyu jigyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With the clean development mechanism (CDM) borne in mind, a study is made about the diffusion of gas driven cooling systems in Oman. The project under study aims to replace the motor driven turbo cooling systems, now in use at the Royal Hospital and other buildings in various areas, with gas driven cooling systems. It is then found that, when the Royal Hotel is equipped with such systems, energy will be saved by 1,855 tons/year in terms of oil, and greenhouse gas reduced by 5,129 tons/year in terms of CO2. When the Royal Hospital and other large buildings with heavy cooling loads, situated at or near the center of Muscat City and in the vicinity of the existing natural gas pipelines, are taken into account, energy will be saved by 13,049 tons/year in terms of oil and greenhouse gas will be reduced by 31,636 tons/year in terms of CO2, thanks to the presence of universities, hotels, and a sector occupied by government offices. As for the time necessary for investment recovery, it will be 4.7-5.3 years in case the investment does not cover a gas decompression station construction cost and 6.2-6.8 years in case it covers such. The new system will cost 7% less than the existing system. When a comparison is made in terms of electricity charges, the new system will be 30% lower than the existing system. The Omani Government is critical of a plan for allowing Japan to establish there an energy supply company (financed by Japan). (NEDO)

Fiscal 1996 report on the committee for international collaborative research of medical and welfare apparatus; 1996 nendo chosa hokokusho (iryo fukushi kiki kokusai kyodo kenkyu jigyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

From a viewpoint that cancer, cerebral hemorrhage, heart disease, etc. caused by the progress in aging are problems not only to Japan but to all developed countries, a possibility of Japan`s joint study with other countries was examined to promote efficiently and effectively research/development of the apparatus required. Moreover, from a viewpoint of being the same Asian countries, a possibility of the joint study was examined also with developing countries which are largely different in disease structure and environment of the use of apparatus from developed countries. In the examination on medical/welfare apparatus technology of China, before the site examination, a book of data was arranged on the actual state of population and disease structure and the R and D situation of medical/welfare apparatus in Japan, and at the same time, celebrated persons in China were introduced by the scientific society side as widely as possible. By this preliminary study, the original objective of the examination could be achieved. In the examination with the U.S. and Europe, Japan held meetings with engineers of the U.K., France and the U.S. Japan`s `load control type walking supporting apparatus,` of which the development was finished, was very highly evaluated by each organ of the countries

Fiscal 2000 report on result of project for promoting exchange of international environmental technology information; 2000 nendo kankyo gijutsu kokusai joho koryu sokushin jigyo seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the purpose of sharing environmental technology information of the APEC countries, the homepage structuring was commenced linking and systematizing the home pages owned by governments, institutions, enterprises, etc., as the APEC Virtual Center (APEC-VC) project, with the fiscal 2000 results reported. In creating the homepage contents, in order to disseminate more useful information for the developing countries, 'Environmental Technology Cooperation for Developing Countries' as the original contents was prepared. In building a search engine, for the purpose of improving convenience for website users of the Virtual Center, APEC VC Japan created a retrieval system on the site. In overseas investigation, the researchers visited local plants to grasp problems and the needs by enterprises and organizations on water-pollution, waste treatment and the like, with the purpose of reflecting the investigation result in the website. In addition, the researchers visited APEC VC coordinators and/or contact points to exchange opinions with the view of expanding the network. (NEDO)

Fiscal 2000 report on result of project for promoting exchange of international environmental technology information; 2000 nendo kankyo gijutsu kokusai joho koryu sokushin jigyo seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the purpose of sharing environmental technology information of the APEC countries, the homepage structuring was commenced linking and systematizing the home pages owned by governments, institutions, enterprises, etc., as the APEC Virtual Center (APEC-VC) project, with the fiscal 2000 results reported. In creating the homepage contents, in order to disseminate more useful information for the developing countries, 'Environmental Technology Cooperation for Developing Countries' as the original contents was prepared. In building a search engine, for the purpose of improving convenience for website users of the Virtual Center, APEC VC Japan created a retrieval system on the site. In overseas investigation, the researchers visited local plants to grasp problems and the needs by enterprises and organizations on water-pollution, waste treatment and the like, with the purpose of reflecting the investigation result in the website. In addition, the researchers visited APEC VC coordinators and/or contact points to exchange opinions with the view of expanding the network. (NEDO)

Fiscal 2000 report on regional new energy vision formulation project for Yunomae town, Kumamoto prefecture; 2000 nendo Yunomaecho chiiki shin energy vision sakutei nado jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-02-01

A regional new energy vision has been formulated for Yunomae town, Kumamoto Prefecture, from the standpoint that local autonomies are required to work out measures compatible with Government energy policies and thereby to wrestle with environmental measures being undertaken across the world. The results of activities conducted for this purposed are stated in six chapters, which cover (1) the meaning of regional new energy vision formulation and its position, (2) outline of Yunomae town, (3) energy and environments, (4) energy situation in Yunomae town, (5) Yunomae town's regional new energy vision, and (6) plans for promoting the embodiment of the vision. In chapter (5), basic policies toward new energy utilization, overall plan, leading projects, and energy conservation measures are stated. The types of new energy taken up for discussion are photovoltaic power, wind power, biomass power, refuse-derived energy, and hydraulic energy. Projects are subjected to study, which relate to photovoltaic power generation, solar heat utilization, small scale hydroelectric power, small scale wind power, and the introduction of clean energy vehicles. It is expected that these projects when carried out will cover approximately 10% of the current energy consumption of the town. (NEDO)

Achievement report for fiscal 1981 on solar system survey projects implemented overseas. Singapore and Australia; 1981 nendo solar system kaigai chosa jigyo seika hokokusho. Singapore Australia

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-06-01

During a 20-day survey tour to Singapore and Australia which started on February 7, 1982, visits were paid to 6 universities, 2 national or state research institutes, 2 state government agencies, 6 passive solar facilities, and some industrial societies and solar equipment manufactures. At universities and research institutes, research and experiments are earnestly under way for the development of solar heat collectors, for the research and testing of software programs therefor, and for the research and development of photovoltaic and geothermal power generation systems. In the case of photovoltaic power, in particular, many programs require the construction of pilot plants and simultaneous supply of power to general consumers with tests and experiments continued for the pilot plants for putting the technology to practical use. This is thought to demonstrate the urgent need for measures for out-of-the-way locations. Electric power is priced at 7-8 yen/kWh, approximately half the price in Japan. Marginal supply capability is low because power is generated mainly by coal and no nuclear power is available. Efforts at underground reserves exploitation have become very active and, since there is need to supply power to the back regions, funds are eagerly invested in on-site power generation and photovoltaic power development. In Australia, power supply is monopolized by state governments. Even in Australia, who enjoy 65% self-sufficiency in oil and export a substantial amounts of natural gas and coal, there are enthusiastic efforts at harnessing solar energy. (NEDO)

FY 1998 survey report on the project on field tests for high-efficient industrial furnace introduction. Manual; 1998 nendo koseino kogyoro donyu field test jigyo mannual

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The high-efficient industrial furnace is a technology with the use of ultra-high temperature air over 1,000 degrees C, which has been impossible. It has been developed since FY 1993. The technology can reduce the energy consumption amount by 30%, and there is a possibility of reducing not only CO2, but NOx by approximately 50% over the conventional method. The main technique of the technology is to preheat the air blown into the incinerator at much higher temperatures of 1,000 degrees C or more than those in the existing combustion and to blow fuel into that high-speed air flow using the short-time-change/heat-storage type heat exchanger. It was predicted that the target value set first can almost be reached, and there can be seen a possibility of its industrial application. Industrial furnaces are used in many industrial fields such as metal production industry, petrochemical industry and electric machinery industry. The energy conservation in these fields brings extremely marked effects, and therefore it is an urgent task to introduce the industrial furnace into the fields quickly. The concentrated R and D were finished in FY 1998, and the field test project for the introduction was actually started. (NEDO)

FY 2000 research cooperation project on plastic processing technology/quality inspection technology; 2000 nendo kenkyu kyoryoku jigyo. Plastic kako gijutsu hinshitsukensa gijutsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of improving the production technology of plastic products in Saudi Arabia, the joint development was made of the formation technology/quality inspection technology of agricultural use and food packaging use polyolefin film optimum to environmental conditions of the site, in the light of the needs there, and the FY 2000 results were reported. In the field survey/joint study, for the xenon type weather resistant testing machine and the extruder of the inflation film forming machine which were transported from Japan, the following were carried out: confirmation of the situation of accepting them on the site, functional test of computer of the extruder, installation of the machine testing weather resistance, and the trial operation. In the domestic support study, the extrusion test at laboratory was conducted using the polyethylene resin produced on the site to acquire the basic data for formation stability. Further, the film formation test was made using the equipment with the same specifications as those of the equipment introduced to the site to study the performance of screw extrusion and the formation stability of film. Also conducted were the analytical test/quality evaluation of resin materials/film. (NEDO)

Report on FY 1998 project for international energy utilization rationalization, etc. (Project of the analytical tool survey for making energy consumption effective in Asia); 1998 nendo chosa hokokusho. Kokusai energy shiyo gorika nado taisaku jigyo (Asia energy shohi koritsuka bunseki tool chosa jigyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In the Asian region, for the purpose of grasping effects of both economic growth and effective energy consumption, an analytical tool added with a computational function was developed with the interindustrial relations table as database for the analysis of the present situation and the simulational analysis. In the analysis of the present situation, changes between the two time-points, 1985 and 1990, were analyzed using the developed energy consumption table and the CO2 emission table. The energy consumption amount is increasing with the growing economy. However, the energy unit consumption is decreasing in countries except Korea, the Philippines, Singapore and Malaysia. The trend is that the energy consumption is becoming effective and the CO2 emission amount is decreasing. As an example of simulating the introduction effect of energy saving technology, the simulation was conducted on the three: iron steel, paper/pulp, and cement in Indonesia. As a result, the decrease in energy consumption was shown in paper/pulp by 48%, in cement by 16%, and in iron/steel by 16%. The same was also indicated in CO2 emission. (NEDO)

Report on achievements in fiscal 1999 on international model project for energy consumption efficiency improvement. 'Model project to enhance boiler and turbine efficiency'; 1999 nendo kokusai energy shohi koritsuka tou moderu jigyo seika hokoku. Boira gasu tabin koritsu kojo moderu jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective to save energy, reduce electric power generation cost, and reduce CO2 exhaust in Indonesia, the Japanese energy saving technologies were transferred to the Muara-Karang Power Station in Indonesia as the object of the project. This paper reports the achievement in fiscal 1999. The target was set to reducing the power generation unit requirement (heat consumption ratio, kcal/kWh) by 1% by improving such constitutional devices as water condensers and air pre-heaters. Further improvements were planned by introducing the thermal efficiency control program. The subject fiscal year has performed data acquisition from the site surveys, investigations on related technologies, and detailed designs for site construction and effect identification. Also having been carried out based on the result of the detailed designs was partial fabrication of members and parts necessary for facility modification such as for small tubes for water condensers made of new materials. Furthermore, the Indonesian engineers were accepted for the purpose of transferring the thermal efficiency management methods, and the maintenance and control technologies for devices being the objects of the facility modification related to the boiler and turbine efficiency improvement. (NEDO)

Fiscal 1998 intellectual infrastructure project utilizing civil sector functions. Research and development project on prompt-effect type intellectual infrastructure creation (Comprehensive survey); 1998 nendo minkan no kino wo katsuyoshita chiteki kiban jigyo seika hokokusho. Sokkogata chiteki kiban sosei kenkyu kaihatsu jigyo (sogo chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Surveys and studies were conducted to facilitate and invigorate research, development, and economic activities and to provide technology related intellectual assets in an organized, systematic way. In the survey related to the buildup of intellectual infrastructures, questionnaires were sent to 789 organizations in the industrial and academic domains concerning measuring standards, reference materials, base for information on biological resources, base for safety management of chemical substances, base relating to human life and welfare, and base of knowledge relating to materials. On-site surveys were also conducted in Asia, Australia, North America, and Europe. Concerning 10 inorganic reference solutions whose development is urged because they are related to environments, raw materials for them were selected, required purity levels were defined, and methods for measurement and evaluation of safety when in prolonged preservation were investigated. Conducted in the research and development of individual subjects were database buildup on thermophysical properties, research into long-term durability of heat-resistant composite materials, research into textural structure and characteristics as materials of sintered bodies of fine ceramics, database buildup on the safety of non-ferrous metals, studies of base of human characteristics measurement, and the like. (NEDO)

FY 1999 investigational survey on the project on the potential survey of the effective energy utilization model project in the Asian region; 1999 nendo Asia chiiki ni okeru kokateki energy yuko riyo model jigyo no jisshi kanosei ni kansuru chosa jigyo seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

A survey was made on the technology applicable to the energy effective utilization model project in the Asian region. In the survey, the technology was listed up which could be the base for the model project in which the use in the commercial/residential field and the use of natural energy were considered. Further, countries for survey were limited to developing countries in the Asian region. Technologies for survey were as follows: various cogeneration systems, fuel cell cogeneration systems, heat storage type heat utilization, heat storage type air conditioning using night power, night power use dynamic ice maker and heat storage tank utilization, low temperature exhaust heat use adsorption type refrigeration, low temperature waste heat recovery absorption type heat pump, low head hydroelectric power generation, energy conservation in buildings, rationalization of energy utilization by energy management, heat supply using solar energy/wind power energy, biomass energy utilization, high efficiency/multiple effect heat utilization, high performance membrane separator utilization, high temperature/high humidity drying, airless dryer, etc. (NEDO)

Report on achievements in fiscal 1996. International energy usage rationalization project (project to survey energy consumption efficiency improvement analyzing tools for Asia/data edition); 1996 nendo kokusai energy shiyo gorika taisaku jigyo chosa hokokusho shiryohen. Asia energy shohi koritsuka bunseki tool chosa jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-10-01

This paper is a collection of data on surveys for energy consumption efficiency improvement, taking Japan, Korea, Indonesia, Thailand, and Philippines as the object countries. I. Industry related various value tables consist of the following: basic transaction table, throw-in coefficient table, final demand converter table, import coefficient table, added value coefficient table, inverse matrix coefficient table, sensitivity coefficient table, influence coefficient table, production inducing amount, production induction dependence, import inducing amount, import induction coefficient, import induction dependence, and inverse matrix coefficient table. II. Energy related various coefficient tables consist of the following: inherent unit quantity table, energy consumption table, CO2 table (1), CO2 table (2), unit requirement table, energy consumption induction table, energy consumption induction coefficient table, energy consumption induction dependence table, CO2 induction table (1), CO2 induction coefficient table (1), CO2 induction dependence table (1), CO2 induction table (2), CO2 induction coefficient table (2), and CO2 induction dependence table (2). Industries are classified into 34 kinds. III. The energy consumption table, CO2 table (1) and CO2 table (2) are shown as the simulation results for the four countries: Korea, Indonesia, Thailand, and Philippines. (NEDO)

FY 2000 Feasibility study on the environmentally-friendly coal utilization systems as part of the international project for coal utilization measures. Feasibility study on supporting introduction of the environmentally-friendly coal utilization systems in Vietnam (Model project for introduction of advanced coal preparation systems); 2000 nendo kokusai sekitan riyo taisaku jigyo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa jigyo Vietnam ni okeru kankyo chowagata sekitan riyo system donyu shien jigyo (kodo sentan system donyu model jigyo kanosei chosa jigyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-06-01

The feasibility study was conducted on a model project in Vietnam, aimed at solving the environmental pollution problems resulting from use of coal by demonstrating and disseminating the Japan's environmental technologies in the Southeast Asian countries. The feasibility study was conducted for the Cua Ong Coal Preparation Enterprise, which has the largest coal preparation capacity in Vietnam and port facilities. It is treating raw coal from 10 coal mines for classification and preparation, and shipping coal of various types that meet the standards for domestic use and export. The survey results point out that unrecovered coal remains in waste water discharged from the coal preparation plants to pollute the sea area, and that quantity of the refuse increases because of the unrecovered coal it contains. The environmental technologies needed to introduce include modification to variable wave pattern type jigging separator, refuse height measuring instrument and automatic controller, circulating heavy medium gravimeter, highly functional settling pond, and flocculent facilities. (NEDO)

Fiscal 2000 survey report on rationalization project for international energy conservation, technological dissemination project for international energy conservation, and Green Helmet Project. Japan-China alternative energy seminar/waste disposal; 2000 nendo kokusai energy shiyo gorika nado taisaku jigyo, kokusai energy shohi koritsuka nado gijutsu fukyu jigyo, green helmet jigyo chosa hokokusho. Nicchu sekiyu daitai energy seminar haikibutsu shori

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This paper explains the Japan-China alternative energy seminar (February 28 and March 1, 2001, at Beijing). The purpose of the seminar is to introduce systematic and three-dimensional or land/sea/air measures for waste disposal including recycling in Japan, to provide guidance of measures in improving recognition and methods for waste disposal in China, and also to contribute to the dissemination and promotion of a model project for effectively utilizing waste heat from rubbish incineration, a project being implemented in Harbin City now. The activities of NEDO were introduced, with emphasis placed on a model program, called Green Aid Project, for managing heat from waste incineration. On the subjects of sustainable development, urban environment, and energy, the policy of China's tenth five-year plan was demonstrated, and the treatment of wastes in China was also explained. The present state of waste processing in Japan was introduced, as was its maintenance of the facilities. Concerning Japan's waste processing technologies and characteristics of the equipment, there were presented non-incineration processing including crushing/separating, RDF, compost, methane fermentation, etc.; incineration plants; and each of the technologies such as combustion, exhaust gas, ash treatment, use of remaining heat, and gasification melting. (NEDO)

FY 2000 Report on the survey results. Survey on international cooperation for medical treatment/welfare equipment; 2000 nendo iryo fukushi kiki kokusai kyodo kenkyu jigyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The NEDO's representatives visited Europe and China with the objectives of, e.g., international cooperation and information exchanges for medical treatment/welfare equipment. For the welfare equipment technologies, they visited the research institutes and facilities in UK and Germany, among others, to find that the European countries place more emphasis on researches to meet the needs than on advancing the equipment itself. For the medical treatment equipment, they visited the bio-research institutes in Europe for exchanging information on post-genome and tissue engineering. The European countries are behind USA in research fund and manpower for bio-technology and bio-medical, although making great efforts with much expectation on these areas. The China's medical treatment/welfare technologies seem to be clearly still in the stage of needing aids rather than rendering cooperation. However, China has been producing a number of new products in the areas where her traditional arts of medicine are combined with advanced techniques of the West, e.g., those for examination, as felt from a number of the equipment types presented to the China Medical Treatment Equipment Exhibition. (NEDO)

FY 1999 report on the survey of the international joint research project on medical welfare equipment; 1999 nendo iryo fukushi kiki kokusai kyodo kenkyu jigyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of internationally cooperating in the R and D of medical welfare equipment, visits were paid to Australia and the U.S. to survey the related administration/research institutes/medical welfare facilities. Australia is a world leader of heart (transplant) operation, organ transplant, artificial middle ear, apneic relaxation equipment, ophthalmological equipment, bio-materials, etc. The country wants to positively promote the international cooperation with Japan because both countries are complementary to each other. Starting about 1999, the U.S. entered the age of competition of the R and D with the use of genome, and the post-genome age is already beginning there. A number of ventures are running for creation of new industry. As to the U.S. government's measures taken for subsidy, regulation, etc. toward new industry, the information could be obtained from the persons concerned. The impression of a tour of welfare facilities in the U.S. was that hardware/software are systematically prepared there, and the aged live bright and positive lives and enjoy lives. (NEDO)

1998 Annual Study Report. New industry supporting type international standard development program (Comprehensive survey); 1998 nendo seika hokokusho. Shinki sangyo shiengata kokusai hyojun kaihatsu jigyo (sogo chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Summarized herein are results of the survey on a total of 13 themes for international standardization. These themes are for standardization of (1) color control, (2) securing interoperability between optical disk systems, (3) digital image processing for home digital electronic appliances, (4) securing interconnectability between home electronic information appliances, (5) production process systems, (6) testing and evaluation methods for fine ceramic materials for communications, (7) evaluation methods for high-temperature properties of new glass melts, (8) corrosion testing and evaluation methods for surface-treated steel plates, (9) testing and evaluation methods for high-purity titanium, (10) testing and evaluation methods for plastic optical fibers, (11) evaluation methods for high-strength, large-size steel pipe characteristics for superhigh-pressure natural gas pipelines, (12) methods for measuring mileage of hybrid electric vehicles, and (13) methods for determining recycle ratios of automobile components. This comprehensive survey also includes overseas trends for the standardization, establishment/expansion of the international standardization processes, and standardization for determining recycle ratios of home electric appliances. (NEDO)

Fiscal 1999 technical survey report. Basic survey of prioritized fields in South Asia (Bangladesh); 1999 nendo Minami Asia chiiki (Bangradesh) energy tashohi sangyo kiso chosa jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For working out and proposing project themes optimum for the popularization of technologies for effectively utilizing energy in Bangladesh, a basic survey was conducted into Bangladeshi energy policy, trend of supply and demand, steelmaking industry, cement making industry, and chemical fertilizer making industry. Bangladesh in fiscal 1997 consumed 10-million tons of energy in terms of oil, 60% or more in natural gas (domestic), 20% in oil, and the remaining 20% in others. Approximately 15% of all the households were supplied with electric power. There was no integrated production plant in the steelmaking industry. Only one mill performed calcination in the cement making industry. The impact to be imposed by the steelmaking and cement making industries on Bangladeshi energy consumption would be small. Fertilizer making was an important industry outputting 2.6-million tons, responsible for 30% of natural gas consumption. The highest priority was given to facility rehabilitation and production enhancement, and there was little hope that energy conservation facilities/technologies would be introduced into the steelmaking and fertilizer making industries. It was possible, however, that the horizontal tube mill would be replaced by a vertical roller mill in the cement making industry. (NEDO)

FY 1999 report on the survey of the international joint research project on medical welfare equipment; 1999 nendo iryo fukushi kiki kokusai kyodo kenkyu jigyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of internationally cooperating in the R and D of medical welfare equipment, visits were paid to Australia and the U.S. to survey the related administration/research institutes/medical welfare facilities. Australia is a world leader of heart (transplant) operation, organ transplant, artificial middle ear, apneic relaxation equipment, ophthalmological equipment, bio-materials, etc. The country wants to positively promote the international cooperation with Japan because both countries are complementary to each other. Starting about 1999, the U.S. entered the age of competition of the R and D with the use of genome, and the post-genome age is already beginning there. A number of ventures are running for creation of new industry. As to the U.S. government's measures taken for subsidy, regulation, etc. toward new industry, the information could be obtained from the persons concerned. The impression of a tour of welfare facilities in the U.S. was that hardware/software are systematically prepared there, and the aged live bright and positive lives and enjoy lives. (NEDO)

Regional new energy vision formulation project for Ukiha Town. Fiscal 2001 report (Summary); 2001 nendo Ukiha machi chiiki shin energy vision sakutei tou jigyo hokokusho (Gaiyo ban)

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-02-01

For contributing to the preservation of the global environment through new energy application and energy conservation, efforts were made to work out a new energy vision for Ukiha Town, Fukuoka Prefecture. Town's population was 17,482 in fiscal 2000, which showed a tendency to decline slowly. The town demands 158,886 drums/year in terms of crude oil - 56.2% in electric power, 19.5% in gasoline, and 10.5% in gas oil. As for the presence of new energy resources, wind power comes in first in terms of magnitude, and woody biomass energy is also found in abundance since lumbering prospers in the town. Named as candidate projects in the efforts to introduce new energies were the embodiment of practical size wind power systems in the hilly part; heat utilization and power generation using biomass such as scrap wood from lumber mills; introduction of photovoltaic power into public facilities; use of clean energy vehicles by the town office; photovoltaic power generation and solar heat utilization at welfare facilities and public gymnastic halls; street lamps lighted by hybrid power systems in the shopping area and at the Michinoeki roadside service spot; use of new energies in agriculture; financial aids to encourage photovoltaic power into general residences; etc. (NEDO)

Fiscal 1999 technical survey report. Green Helmet Project (China, Steel industry - Coal moisture control facilities); 1999 nendo green helmet jigyo (Chugoku seitetsugyo) sekitan choshitsu setsubi chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of meeting the needs of Chinese steelmaking corporations disclosed at an energy conservation diagnosing session of a Japan-China steelmaking energy conservation seminar held in July 1999, Japanese specialists were sent to Chinese steelmaking plants, namely, Benxi Iron and Steel (Group) Complex, Wuhan Iron and Steel (Group) Company, and Nanjing Iron and Steel Works. They described the CMC (coal moisture control) technique for its popularization and for effectively utilizing the same for coke ovens. Also, feasibility studies were conducted for CMC installation at the respective plants. Engineers were invited from the Chinese plants to Japan for the observation of associated facilities and for the exchange of opinions. As the result, leading members of the Chinese steelmaking plants now learned the usefulness of CMC. In the feasibility studies, CMC installation led to a reduction in dry distillation energy, that is, a reduction in the amount of fuel gas required, to an improvement on coke production, and to the selection of the fluidized bed dryer as the optimum system. At Chungching Iron and Steel Works, the existing CMC facilities were not in continuous operation because of an inclined conveyer failure, yet there was a strong will to utilize the CMC technique. (NEDO)

FY 1998 annual report on the environmental technology working group. 19th R and D activity report; 1998 nendo kankyo gijutsu bunkakai. Dai 19 kai jigyo hokokukai

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

Summarized herein are the FY 1998 activities by the environmental technology working group, extracted from the 19th R and D activity report by NEDO. Mr. Mitsukawa, a NEDO's director, outlines the measures for diversifying environmental problems, prevention of global warming, waste disposal/recycling, and toxic chemical substances in the report entitled (Outlines of environmental technology development projects). The report entitled (Eco-cement production techniques for comprehensive utilization of urban type wastes (For efforts for construction of Ichihara eco-cement production facilities)) outlines characteristics of eco-cement production techniques, recyclability of eco-cement, and the facilities. The report entitled (Techniques for reutilization of plastics present in wastes as the blast furnace stocks) outlines the system, R and D project and commercialization, and vinyl chloride recycling system, to be developed by the financial support by NEDO. The other reports include (Development of universal controllers for coping with environmental problems) and (R and D of techniques of simplified dioxine analysis). (NEDO)

FY 1997 Report on New Sunshine Project. International co-operative projects (Australia-Japan solar energy technology cooperation, etc); 1997 nendo kokusai kyoryoku jigyo. Nichigonado taiyo energy gijutsu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Described herein are the progresses, memorandum concluded for the new project, NEDO/MUERI project activities, among others, for, e.g., Australia-Japan solar energy technology co-operative project. The photovoltaic cell outdoor exposure test project has been progressing as expected in Australia since FY 1996. The test data have been collected for one year and analyzed successively. The second information exchange workshop is scheduled in June 1998 in Sydney for the thin-film, polycrystalline photovoltaic cell manufacturing technologies. The new type photovoltaic cell long-term exposure test project has been started in FY 1997 as the new project in Oman. The weather conditions of the test site are very severe, very high both in temperature and humidity. The new type photovoltaic cell modules, centered by the amorphous silicon, will be exposure-tested in the severe atmospheres, to verify long-term reliability of the photovoltaic cells. A total of 5 types of the modules are to be exposure-tested; 3 types of 6 amorphous silicon cells, one type of 2 CdS/CdTe cells, and one type of 2 thin-film polycrystalline cells. (NEDO)

FY 1998 annual report on the fuel/storage working group. 19th R and D activity report; 1998 nendo nenryo chozo gijutsu bunkakai. Dai 19 kai jigyo hokokukai

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

Summarized herein are the FY 1998 R and D activities by the fuel/storage working group, extracted from the 19th R and D activity report by NEDO. Mr. Kadoi, a NEDO's director, outlined the R and D activities for development of techniques for fuel cell power generation, development of decentralized cell power storage systems, demonstration of new load-leveling techniques, development of techniques for superlow-loss type power system components, development of techniques for ceramic gas turbines, pioneer R and D for MGC superhigh-efficiency turbine system techniques, demonstration tests for establishing centralized load controlling systems, development of techniques for network systems utilizing wide-area energy, development of techniques for application of superconductor-aided power systems, R and D for power storage aided by a high-temperature, superconducting flywheel, R and D for basic techniques for applying superconductors, and pioneer R and D for basic techniques for AC superconducting power equipment. The individual NEDO's researchers reported their results, which include outline of the fuel/storage technique development group, and current statuses of fuel cell technique development, new cell-aided power storage technique development, and superconductor technique development. (NEDO)

Report on the project for working out the new energy vision of the Iwasaki village area; 2001 nendo Iwasaki mura chiiki shin energy vision sakutei tou jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-02-01

For the purpose of promoting the introduction of new energy and enhancing the awareness of it at Iwasaki Village, Aomori Prefecture, an investigational study was conducted of the energy demand of the town, existence amount of new energy, introduction of new energy, etc., and a new energy vision was worked out. The population of Iwasaki Village was 2,845 as of October 2000, which decreased approximately 30% in the past 20 years. The energy demand of the whole village was about 280,000 GJ in amount (about 7,202 kL/y in crude oil conversion), consisting of kerosene, light oil, heavy oil, gasoline, electric power and LPG. As viewed by sector, the rate of energy demand in the commercial/residential sector was comparatively high. As the project for new energy introduction, the following were studied: wind power generation around the Yamamori plain/Iwasaki village office; snow melting system using soil heat exchanger on the road in front of elementary school, photovoltaic power generation for public facilities (elementary and junior high schools/house of recreation and relaxation for old people/day nursery)/Tsugaru Semi-national Park/general houses; wave power generation at the Iwasaki fishing port; introduction of clean energy vehicles to public facilities; utilization of ligneous biomass energy, etc. (NEDO)

Report on the project for working out the new energy vision of the Genkai town area; 2001 nendo Genkai machi chiiki shin energy vision sakutei tou jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-02-01

For the purpose of promoting the introduction of new energy and enhancing the awareness of it in Genkai Town, Fukuoka Prefecture, an investigational study was conducted of the estimated amount of energy demand of the town, existence amount of new energy, project for new energy introduction, etc., and a vision was worked out. The energy consumption amount of the town in FY 1999 was estimated at 834 TJ/y. By sector, it consisted of 299.31 TJ in the industrial sector, 282.08 TJ in the transportation sector and 252.78 TJ in the commercial/residential sector. By energy source, the rate of light oil was the highest, followed in order by gasoline, electric power, kerosene, LPG, etc. As the project for new energy introduction, the following were studied: preparation of disaster-prevention type photovoltaic power generation at shelter, etc.; introduction of photovoltaic power generation to kindergarten, elementary school, etc.; introduction of photovoltaic power generation to street light, tourist information center, etc.; introduction of wind power generation to public facilities; use of the waste cooking oil made into diesel fuel for official vehicle; introduction of cogeneration to the health welfare hall; solar light/heat utilization system for residential/industrial use; wind power generation business for business establishment. (NEDO)

Fiscal 2000 report on cooperative basic project on international energy consumption improvement/International conference project such as IPCC. International Symposium on the Kyoto Mechanisms; 2000 nendo kokusai energy shohi koritsuka nado kyoryoku kiso jigyo / IPCC nado kokusai kaigi jigyo Kyoto mechanism ni kansuru symposium hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-06-01

The above-named symposium was held at United Nations University in the period April 12-13, 2001, and the conference is outlined in this report. The symposium aimed to contribute to the progress of international rule making and to the enhancement of mutual understanding through the exchange of views and opinions by negotiators representing their countries over the Kyoto mechanisms, the rule of emissions trading in particular, and through the analysis of negotiators' options; to discuss how international rules should be from a practical viewpoint with the participation of people related to the market or industries and engaged actively in the implementation of the mechanisms; to enrich Japanese people's knowledge about the mechanisms and to enhance their understanding of greenhouse gas emissions reduction techniques making use of the mechanism of the market; and so forth. The conference included Session 1: Current status of international negotiations and views from parties, Session 2: Toward credible and workable scheme of the mechanisms (Parts 1 and 2), and Session 3: Emissions trading - Outstanding issues and options. (NEDO)

FY 2000 report on the coal resource development basic survey (information collection analysis project). Cooperative project on the open-cut coal mine rehabilitation technology; 2000 nendo sekitan shigen kaihatsu kiso chosa (joho shushu kaiseki jigyo) hokokusho. Rotenbori sekitan saikutsu atochi shufuku gijutsu kyoryoku jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

At the Ensham open-cut mine in Australia, an investigational survey was conducted of a new rehabilitation technology which can contribute also to securing CO sink with the aim of preventing global warming, and the FY 2000 results were summed up. In the survey, the surface soil, sand silt layer, brown rock layer, gray sandstone layer and coal seam were moved from open pits, the goaf was embanked, and the experimental section was set up. As to the place for test, conducted were collection of information on adaptive plant species, bacterium species, meteorology and precipitation pattern, soil analysis, etc. Concerning the bacteria, bacteria were newly separated and tested at the survey site, besides the species to be tested. After planting, measurement of the growth amount of plants, etc. were conducted grasping the meteorology and the water-pouring state during cultivation. For the basement, three kinds of spoils were used, and permeability is different in each spoil. Permeability is an important factor to plants. Too good permeability and too bad permeability are both not good. A future follow-up survey will make what kind of spoil is suitable for eucalypti possible. (NEDO)

FY 1999 Feasibility study on the environmentally-friendly coal utilization systems. Green Helmet Project (Circulating fluidized bed boiler Zaozhuang, Shangdong Province, China); 1999 nendo kankyo chowagata sekitan riyo system kanosei chosa jigyo seika hokokusho. Green helmet jigyo (junkan ryudosho boiler Chugoku Shangdong sho Zaozhuang)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The demonstration project is carried out in at Chaili coal mine in Shangdong Province, China for installation of and dissemination activities for circulating fluidized bed boilers to abate sulfur oxide emissions associated with utilization of coal, and the FY 1999 results are reported. The operating conditions were reviewed, and some recommendations were made for improving the operation procedures. Limestone was not used for desulfurization, and furnace temperature tended to increase due to increased size of the fluidizing particles. Therefore, it was recommended to use limestone at the design rate. The boiler was operated at a load exceeding the design level, and it was recommended to limit the load viewed from extending serviceability. The boiler start-up procedure was concretely proposed to use a mixed fuel of wood and coal instead of distillate oil, in order to reduce the start-up cost. The recommendations and design support activities for improving facilities included early stage repair of the damaged refractories. For build up of the ashes in the horizontal heat transfer section, the investigated design charts for improvement by installation of ash-discharging hopper were drawn and proposed. Maintenance-related information was given, including Chinese agencies for obtaining auxiliary facilities. (NEDO)

Fiscal 2000 report on cooperative basic project on international energy consumption improvement/International conference project such as IPCC. International Symposium on the Kyoto Mechanisms; 2000 nendo kokusai energy shohi koritsuka nado kyoryoku kiso jigyo / IPCC nado kokusai kaigi jigyo Kyoto mechanism ni kansuru symposium hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-06-01

The above-named symposium was held at United Nations University in the period April 12-13, 2001, and the conference is outlined in this report. The symposium aimed to contribute to the progress of international rule making and to the enhancement of mutual understanding through the exchange of views and opinions by negotiators representing their countries over the Kyoto mechanisms, the rule of emissions trading in particular, and through the analysis of negotiators' options; to discuss how international rules should be from a practical viewpoint with the participation of people related to the market or industries and engaged actively in the implementation of the mechanisms; to enrich Japanese people's knowledge about the mechanisms and to enhance their understanding of greenhouse gas emissions reduction techniques making use of the mechanism of the market; and so forth. The conference included Session 1: Current status of international negotiations and views from parties, Session 2: Toward credible and workable scheme of the mechanisms (Parts 1 and 2), and Session 3: Emissions trading - Outstanding issues and options. (NEDO)

Fiscal 2000 project on measures for assisting and diffusing environmentally-friendly coal utilization system introduction. CMG recovery/utilization system joint demonstration project; 2000 nendo kankyo chowagata sekitan riyo system donyu shien nado fukyu taisaku jigyo chosa hokoku. CMG kaishu riyo system kyodo jissho jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A CMG (coal mine gas) recovery/utilization system was designed, constructed, and then demonstrated at a model coal mining district in Liaoning Province for the purpose of contributing to the solution of energy and environment related problems in China. The recovery system demonstration test, aiming to improve on safety and productivity of coal mining and to supply recovered gas with stability, involved gas drainage test boring, mine sealing, sealed gas induction control, centralized gas monitoring, etc., which were carried out at the coal mine working face. A utilization system demonstration test was conducted, and CMG would continue to be supplied to the current users and CMG utilization would be started at the other 6 coal mines. For the supply of CMG to large-scale gas consuming areas, steel materials were manufactured and processed for spherical gas holders and denitrification facilities, gas holders were constructed, pipe lines were installed, and a provisional gas supply was carried out. For the transfer and diffusion of the technology, Chinese engineers were trained in Japan and Japanese engineers were dispatched to China. (NEDO)

FY 2000 report on the results of the project for the promotion of industrial technology development for the global environment. Project on the investigational research of high technology; 2000 nendo NEDO seika hokokusho. Chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo - Sentan gijutsu chosa kenkyu jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

High-tech study was conducted for fields of CO2 fixation/effective utilization, technical development of low environmental load substances and technical development of environmentally friendly type production process, and the FY 2000 results were summarized. Out of the proposals for research projects collected in FY 1999, 25 projects that were recognized to be excellent were consigned to contract research. Research Institute of Innovative Technology for the Earth also selected 4 projects for research. Through research activities, 179 projects were made public, and 2 patents were applied for. The number of research themes was 29 including the following themes: development of food resource resistant to the future global environment, study on new circulation type polymer chemical recycling by bio-process, development of dioxin decomposition technology using artificial enzyme and absorption resin, design of rare metal free cathode substance for large lithium ion secondary battery, and reforming of carbon circulation system in the Australian desert by natural humus supply. (NEDO)

Fiscal 2000 project for promoting international cooperation for global environment. International information network project for global environment (Survey on information network for environmental technology transfer); 2000 nendo chikyu kankyo kokusai kyoryoku jigyo hokokusho. Chikyu kankyo kokusai joho network jigyo (kankyo gijutsu iten joho network chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Environmental technology information database has been shown on Internet for the purpose of transferring environmental technologies; in order to reinforce it this year, a viewpoint was directed to developing countries, with research carried out on the environmental preservation information of the Philippines and Thailand. In the research, in view of promoting cleaner production in developing countries, UNEP regional offices, which are active in the operation, and Asian Development Bank were examined, with their methods, plans and strategies of disseminating the cleaner production surveyed. Also, the database was added with the activities by the organizations concerned in Philippines and Thailand. As for the environmental management system ISO14001, some local governments in Philippines and Thailand will presumably acquire ISO14001 in the future to deal with their environmental management; under the circumstances, Miyama Town was chosen that was first in Mie Prefecture to obtain ISO14001, with the details investigated concerning its environmental policy and the acquisition of ISO14001; and, on the basis of the investigation, a database was prepared so that guidelines for environmental management were provided for the local governments. (NEDO)

FY 1999 report on the survey of the basic cooperation project of enhancement of the international energy consumption efficiency. Project on promotion of exchanges with the persons concerned with government agencies, etc.; 1999 nendo kokusai energy shohi koritsuka nado kyoryoku kiso jigyo, kokusai energy shohi koritsuka chosa nado kyoryoku kiso jigyo chosa hokokusho. Seifu kikan nado kankeisha koryu sokushin jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of promoting the understanding of effective energy utilization and constructing corporative relations between countries, the persons concerned with government agencies of India, China, Indonesia, Vietnam, Myanmar and Thailand were invited to Japan, and exchanges of opinions were made on policies, technical development, the state of the introduction, etc. The persons concerned with governments of India, China and Indonesia participate in NEDO Forum 2001 to give lectures on the energy policy of their own. The persons sent from the Vietnamese government paid visits for survey to NEDO, Obayashi Corp., Kawasaki Heavy Industries, Ltd., Mitsubishi Materials Corp. and Taiheiyo Cement Corp. as reference of the model project on cement sintering plant power reduction. The persons sent from the Myanmar government paid visits for survey to NEDO, ECCJ, Chiyoda Corp., Yokogawa Electric Corp. and Cosmo Oil Co. as reference of the model project on energy conservation at fertilizer plant. The persons concerned with the Thai government paid visits for survey to the plants concerned with the model project on residue combustion waste heat recovery facilities at paper mills and the model project on waste heat recovery at steel material heating furnace. (NEDO)

FY 2000 report on the survey project on the environmentally friendly energy community, excluding mostly projects on electric power generation. Survey project on the environmentally friendly energy community in the Nagoya area; 2000 nendo kankyo chowagata energy community chosa jigyo 'shutoshite hatsuden jigyo ni kakawaru mono wo nozoku' chosa hokokusho. Nagoya chiiki ni okeru kankyo chowagata energy community chosa jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The paper studied the working-out of the basic plan on the RPF (refuse paper and plastic fuel) production business in the area mainly including Nagoya city and of the business profitability. RPF is a solid fuel made by grinding, mixing and pressurizing paper and plastics in appropriate sizes. Its shape and calorific value can be adjusted according to the needs. In the Nagoya area, the demand for RPF is more than the supply, and therefore a much larger amount of RPF is in need. In Phase 1, business was studied for paper and plastics in the container packing paper waste and business-derived general waste. As a result, the RPF production amount was 21,000 t/y, which is equivalent to the effect of reduction of the same amount of coal. As to the profitability, it was made clear that the business can be profitable if collecting 41,400 yen/ton as the re-commercialization cost. In Phase 2, the design of the facilities was made for the larger-sized commercialization by adding industrial waste plastics to the waste in Phase 1. (NEDO)

Research report for fiscal 1998. Research for 'New Earth 21' project implementation program preparation; 1998 nendo chosa hokokusho. 'Chikyu saisei keikaku' no jisshi keikaku sakusei ni kansuru chosa jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For the establishment of a CO2 measures introduction scenario which the world would accept, the latest information was collected, the DNE21 (Dynamic New Earth 21) model was improved, and simulation was reviewed. In fiscal 1998, simulation was performed for each district using an LDNE21 (Linear Dynamic New Earth 21) model, and an energy flow chart, energy balance table, and trade table were prepared and subjected to detailed deliberation. Studied were also conducted about the changes to occur in methanol production when the natural gas reserves and plant cost data were given different values. In the DNE21 model, the 'macro economy model' and 'warming damage function' were integrated, and simulation was performed for verification. Using a standard model compatible with COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change), comparison was made between a case in which different CO2 emission constraints were imposed on the advanced area and developing area separately and a case in which one and the same constraint was imposed on the world as a whole, and calculations were made about CDM (Clean Development Mechanism). (NEDO)

FY 2000 Project report on survey for drawing district energy-saving visions for City of Oguchi; 2000 nendo Oguchi-shi chiiki sho energy vision sakutei nado jigyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-02-01

The energy-saving visions are drawn for City of Oguchi to help spread the energy-saving practices through the citizens, based on the studies on more efficient and realizable energy-saving measures, including effective utilization of district energy. The energy-saving activities cover the following 6 areas: (1) energy demand trends and current status of energy-saving measures, (2) basic environmental conditions related to energy saving in the district, (3) prediction of energy demands, (4) basic conception of the district energy saving, and introduction methodology, (5) energy-saving implementation plans, and (6) promotion of and problems involved in introduction of the energy-saving measures. The energy-saving implementation plans cover the public facilities, household, schools and private enterprises, and the energy-saving measures studied for the public facilities include introduction of microhydroelectric power generation systems for service water and sewer systems, revolving doors for libraries, high-efficiency illumination systems, and various types of solar systems. Those for household include economic utilization of home electric appliances and automobiles, and those for cooperation by the administration and citizens include thorough separation of garbage. (NEDO)

Report on the project for working out the new energy vision of the Shime town area; 2001 nendo Shime cho chiiki shin energy vision sakutei tou jigyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-02-01

For the purpose of promoting the introduction of new energy and enhancing the awareness of it in Shime Town, Fukuoka Prefecture, an investigational study was conducted of the state of energy consumption of the town, existence amount of new energy, project for new energy introduction, etc., and a vision was worked out. The rate of electric power demand of the town consisted of 44% of the residential sector such as general household, the highest, 30% of the business sector such as business office and 21% of the industrial sector such as plant. The demand from the industrial sector was on the decrease. The sales amount of domestic use gas almost leveled off. As the project for new energy introduction, the following were studied: introduction of photovoltaic power system to the Shime town office/townspeople center/elementary school/junior high school; introduction of solar heat utilization system to the welfare center for old people; introduction of wind power/photovoltaic power hybrid street light to school road/cycling road/playground; heat pump space heating/cooling using temperature different energy of the water of mine roadway; introduction of clean energy vehicle to the town office; introduction of photovoltaic power generation/solar heat utilization/hybrid car to general houses. (NEDO)

Fiscal 1997 report on the environment friendly type coal utilization technology transfer project. Downstream field; 1997 nendo gyomu hokokusho. Kankyo chowagata sekitan riyo gijutsu iten jigyo (karyu bun`ya)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For the purpose of supporting the introduction/spread of clean coal technology (CCT) in countries in Asia and the Pacific, engineers of the countries concerned were invited to Japan aiming to ferment the understanding of CCT and improve abilities of them. The project was carried out by NEDO, and managed by CCUJ. It has two courses. The manager course is for policy makers, management and senior managers. By assessing CCT and presenting a menu for economical efficiency, environmental arrangement for CCT introduction is made in working out policies and planning plant/equipment investment in the future. The engineer course is for policy planners, mid-class managers and senior engineers. It proposes data on which to base a decision in working out/planning CCT facilities, and at the same time ideas by which to reduce environmental loads by management of facilities, simple improvements, etc. The number of the persons invited are 21, that is, 8 from China, 5 from Indonesia, 4 from the Philippines and 4 from Thailand. After the training, future subjects were summed up

Fiscal 1999 technical achievement report. Development project on international standards for developing new industry (Comprehensive research); 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Sogo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research and development of 13 individual subjects whose achievements are expected to come into use on the international scale was started in fiscal 1998, to be completed in three years. Progress is reviewed for each of the subjects, and the findings are mentioned below. Research and development is progressing smoothly, specifications to be internationalized have been narrowed down, and it is now foreseen that the main points of the specifications to be presented will be successfully prepared. There are some subjects, however, about which it is difficult to specify to which technical committees they are to be submitted. Assistance, for instance supply of information, by technical committees involved is indispensable. The attitude toward international standardization taken by European and American business corporations visited for study by Japanese researchers is to be disseminated to Japanese business corporations since the information thus collected will help them. Although 75% of the 13 subjects have reached a level where they may be presented as specifications for international standardization, yet they need active support by organizations concerned and research of trends of internationalization-related institutions before they are actually accepted as international standards. (NEDO)

Fiscal 2000 cooperative basic project for investigation of efficiency in international energy consumption. Project for inviting researchers from developing countries (Indonesia, Philippines, Thailand and Vietnam); 2000 nendo kokusai energy shohi koritsuka chosa nado kyoryoku kiso jigyo hokokusho. Hatten tojokoku kenkyusha shohei jigyo (Indonesia, Philippines, Tai, Vietnam)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-02-01

As a part of international cooperation concerning global environmental issues, ICETT (International Center for Environmental Technology Transfer) invited administrative officers, engineers, etc., of developing countries, for the purpose of encouraging experts connected with energy conservation and environmental protection technologies, providing training on the administrative technique, antipollution technologies, energy conservation technologies, etc. The training period was from December 3 to 21, 2000, with 12 participants attended, three each from four countries, Indonesia, Philippines, Thailand and Vietnam. The contents of the technological instruction were such that cases in Japan concerning energy conservation and environmental protection were introduced generally from the administrative measures to the technological countermeasures, as were done conventionally. In the area of the environmental protection, lectures and tours on wastewater treatment were added as industrial wastewater control measures. In the subject of new energy, micro hydraulic power was added which is in progress for example in Indonesia under an aid from Japan. In the energy conservation technology, a supplementary lecture was given on the concept and methodology of an environment-protective type production technology, with emphasis placed on the energy conservation and environmental protection in manufacturing plants and production processes. (NEDO)

Report on fiscal 1996 basic survey project for efficient use of energy in developing countries - database building project. Part 2. Decision on data base dissemination plan; 1996 nendo hatten tojokoku energy koritsuka kiso chosa jigyo (database kochiku jigyo) hokokusho. 2. Database no fukyu keikaku no sakutei

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A dissemination plan was decided on concerning an energy-related database, which has been prepared in the eight countries including Japan in the Asian Pacific region since fiscal 1993. The database is so designed that the energy-related data of the eight countries are retained equally by each country and that the data of all these countries are readily made available in each of these counties in the same manner as retrieving the data of its own. It is necessary that each country establishes a system of amassing data of its own and collecting the data continuously as well as renewing the data mutually with the other countries. The disseminating/enlightening measures of the database were extracted from such viewpoints as enhancing the recognition level, educating/enlightening the usage, teaching the operation method, and customizing the NEDO-DB. In addition, a plan was prepared in which organizations/institutions, as the object of the dissemination and enlightenment in each country, were classified into four groups based on the relation to their counterpart and on the possibility of the database utilization, with a schedule made for each group as to the implementation of each of the disseminating/enlightening measures. (NEDO)

FY 1999 survey report on the global environment international cooperation promotion project/global environment international information network project. Survey of the environmental technology transfer information network; 1999 nendo chikyu kankyo kokusai kyoryoku suishin jigyo / chikyu kankyo kokusai joho network jigyo. Kankyo gijutsu inten joho network chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

At International Center for Environmental Technology Transfer, the following were conducted for enrichment of the environmental technology information: surveys of the state of activities in international organizations and developed countries, cleaner production (CP), ISO, etc. and construction of database. As to the reinforcement of environmental preservation technology information database, enrichment of the data on environmental preservation was attempted mainly about ways of thinking of environmental preservation which brought fruitful results to international organizations overseas. The hierarchization/supplementation were conducted of CP databases which attract much attention especially among developing countries. In the survey of models for environmental preservation, autonomous bodies in Mie prefecture and the certified consultant were taken up to study the process up to the acquisition of ISO14001. The database was so made that it can be a guide for the environmental management in autonomous bodies in developing countries. In the CP survey, as to the United Nations Environment Programme (UNEP), definition/thought were examined in terms of CP, eco-efficiency, pollution prevention, green productivity, etc. (NEDO)

Report on the survey on the project for working out the new energy vision of Oyamada Village; 2001 nendo Oyamada mura chiiki shin energy vision sakutei tou jigyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

For the purpose of promoting the introduction of new energy and enhancing the awareness of it in Oyamada Village, Mie Prefecture, an investigational study was conducted of the energy demand amount, existence amount of new energy and project for new energy introduction, and a vision was worked out. The energy demand amount of the village was 672,289 x 10{sup 3} MJ/y. The rate of energy source was about 27% of electric power and 65% of petroleum-base such as gasoline, light oil and kerosene. The amount of CO2 emitted from these was estimated at 50,333 t-CO2. As viewed by sector, the energy demand amount consisted of 46.7% in the transportation sector, 36.3% in the industrial sector, 9.6% in the residential sector and 7.3% in the business sector. As the project for new energy introduction, the following were studied: Aoyama Heights wind farm (wind power generation: 700kW x 12 turbines); wind power generation project jointly with citizen; introduction of photovoltaic power generation/solar heat utilization to public facilities; greenhouse of Western orchard using waste heat from hot spring, stockbreeding waste utilization project, recycle project for thinnings, introduction of clean energy vehicle, etc. (NEDO)

Research report of fiscal 1997. Joint research project on petroleum substituting energy between Japan and the EU; 1997 nendo chosa hokokusho. Nichi EU sekiyu daitai energy kanren kyodo kenkyu jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Four researchers were invited from EU countries to promote R & D of petroleum substituting energy in Japan, and the joint research was made in institutes of Agency of Industrial Science and Technology related to each theme for 50 days. On the research on deep geothermal prospecting based on volcanic halocarbon group, it was showed that halocarbon discharged from volcanic or hydrothermal system is an important window to survey activities within the earth. On the research on catalyst for hydrogenation of coal-derived liquid, XPS data was reported, and some preliminary conclusions were obtained. On the research on oxide system anode material for Li secondary cells, a method for improving the state of host to ion moving in 1-D to 3-D networks by diffraction method was showed. In particular, the method was effective to offer electronically sensitive environment to moving ion system. On the research on hydro-dechlorination of hydrocarbon halide, the theme related to environmental measures against waste hydrocarbon halide (depletion of the ozone layer) was studied. 83 refs., 32 figs., 20 tabs.

Survey for working out a new energy vision of the Tateshina Town area; 2001 nendo Tateshina machi shin energy vision sakutei chosa hokokusho. Chiiki shin energy vision sakutei tou jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-02-01

For the purpose of promoting the introduction of new energy and heightening the awareness of new energy in Tateshina Town, Kita-saku County, Nagano Prefecture, study was made of the existence amount of new energy, energy consumption amount in the town, project for the concrete introduction, etc., and a 'new energy vision of the area' was worked out. According to the sample survey, in the energy supply/demand structure of Tateshina Town, electricity was 32.2%, kerosene 23.9%, gasoline 17.1%, light oil 11.2%, heavy oil 10.3%, etc. By sector, the commercial/residential sector was 57.1%, transportation sector 25.9% and industrial sector 17.0%. The demand in FY 2010 is expected to increase by 8.9%-22.0% in FY 2010. For the project on new energy introduction, the following were studied: supply of new energy information, support of the introduction to town people, energy utilization of forest resource, preparation of an eco-museum in the Shin-jin'nai forest park, promotion of the tourism using new energy, study of energy utilization of stockbreeding waste, introduction to administrative facilities, etc. (NEDO)

Fiscal 1997 report on the survey project on planning to execute `The New Earth 21`; 1997 nendo chosa hokokusho (`chikyu saisei keikaku` no jisshi keikaku sakusei ni kansuru chosa jigyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Japan proposed in the Houston Summit the New Earth 21 to be carried out with technology development and technology transfer, and to make a concrete development of the project, Japan also proposed in the Tokyo Summit a TREE Plan for working out comprehensive strategies of the innovative technology development. In the CO3 Kyoto Conference in 1997, numerical targets for developed countries were determined which have legal binding force for control/reduction of greenhouse gas emissions in the term of 2008-2012. It was agreed to urge developing countries also to play a certain part in the project through the clean development. Therefore, the paper made quantitative analysis of important CO2 prevention technologies, technology transfer costs, and economical assessment by energy conservation. As a model, the DNE 21 model was upgraded and used into which CO2 prevention technologies, energy, economy and climate changes were integrated. In fiscal 1997, the following were carried out: collection of data on important CO2 prevention technologies and systems and analytical assessment using the DNE 21 model, CO2 reduction and selection of energy technology, assessment of energy system costs, construction of the unified DNE 21 model, and opening of the international workshop. 62 refs., 98 figs., 34 tabs.

Fiscal 2000 business report. Technology transfer project involving environmentally-friendly coal utilization (CCT downstream sector); 2000 nendo hokokusho. Kankyochowagata sekitan riyo gijutsu iten jigyo (CCT karyu bun'ya) - 1

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the clean coal technology (CCT) to be introduced into and popularized in countries in Asia and the Pacific region, Japan invited engineers from these countries and provided them with CCT-oriented education and training. The participants were backbone leaders engaged in the research and development of coal combustion technologies and facilities, in the delivery of technical guidance and education, or in the implementation of environment-related measures back in their enterprises, plants, research institutes, and the like, and they acquired leading-edge technologies, knowledge, and techniques in the field of CCT. The environment course was held in the period of October 14-29, 2000, and the combustion course in the period of November 18-December 17, 2000, and the participants totalling 38 were from China, Indonesia, Thailand, the Philippines, or Vietnam. In this fiscal year, a follow-up survey was conducted in addition to the CCT education and training, which aimed to learn the CCT popularization status in the respective countries involved. It was then found that many of the trainees assumed important positions related to CCT popularization in their countries and were dealing with CCT popularization and implementation. (NEDO)

Fiscal 1996 international research cooperation project. Report on the result of the development survey of tribo materials; 1996 nendo kokusai kenkyu kyoryoku jigyo. Tribo material no kaihatsu chosa seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Basic information was collected and assessed on materials and element technology for tribo materials which are expected to contribute to improvement of energy efficiency of machine/equipment having the sliding part such as automobiles. A survey was conducted of creation of substrate materials, the surface treatment method, and evaluation of coating characteristics. For an analysis of high polymer abrasion powder, the micro ATR method is effective. As an analysis method of abrasion scar, the micro ATR method is effective to specify the peeling part of coating, and the Raman method is effective for an analysis of transfer matters or abrasion powder. As a method to collect various shapes of abrasion powder, processing of material surfaces by polishing method is effective. As a dynamic analysis method, the infrared ray stress image method is effective. As an evaluation method of deficient concentration of coating, the GC-MS method is effective. For the application of high-hardness/low-toughness gas phase coating film to the sliding part, important factors are the substrate hardness, surface roughness, and film adhesiveness from the aspect of materials and the determination of pressure of the sliding face from the aspect of sliding conditions. 12 refs., 38 figs., 20 tabs.

17th Symposium of NEDO projects. Introducing/spreading project subcommittee; Donyu fukyu jigyo bunkakai. Dai 17kai jigyo hokokukai

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-09-01

The results of the following themes are presented in this subcommittee; (1) outline of the new energy introduction promotion department, (2) the project results, and (3) introduction of the examples. For the theme (1), NEDO is supporting the projects for introducing and promoting new energy systems, feasibility studies for introduction of these systems, and field test (FT) projects to accumulate the experiences, e.g., collecting the data by operating these systems under actual loads, development and technology demonstration projects for introduction of new energy systems, and advisory projects for supporting introduction of new energy systems. For the theme (2), those results reported include the results and examples of the FT projects for power generation by photovoltaic cells and wind power generation, results of the FT project for power generation by fuel cells and creation of the FT projects for pioneer high-efficiency energy systems, current status of the environment-friendly energy community projects (heat supply systems), results and examples of the environment- friendly energy community projects (power generation projects), demonstration tests for establishing the distributed power supply systems of the next generation, tests for establishing techniques for, e.g., load-leveling in power generation by photovoltaic cells for residential purposes, results of the project for technology of utilizing unutilized energy, survey on the techniques for power generation by wastes, and advisory projects for supporting introduction of new energy. (NEDO)

Fiscal 1999 survey report. Basic survey project on international cooperation for energy consumption efficiency improvement (Project on cooperation for oil consumption efficiency improvement - Fiscal 1999 survey report on Indonesia); Kokusai energy shohi koritsuka nado kyoryoku kiso chosa jigyo / sekiyu shohi koritsuka kyoryoku chosa jigyo. 1999 nendo Indonesia chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The project aims to contribute to the promotion of international research cooperation ranging from the survey stage through the stages of verification study and popularization, and, for this purpose, it conducts on-site investigations for exploring needs for environmentally-friendly energy-saving technologies in developing countries where there will be massive-scale oil consumption in the future. In this report, surveys and deliberations are conducted to embody proposed measures, and findings are compiled, based on the surveys conducted in the preceding financial year relating to energy efficiency in and environmental technologies for the textile and chemical industries. Much is expected from the proposed measures as promising subjects of joint verification researches. A technology is proposed for energy saving in the textile industry of Indonesia. The technology aims to wash cloth using high-pressure water from a special nozzle, to continuously measure the level of contamination of the waste water, and to feed back the measured values to the water supply side for the automatic optimization of the amount of the washing water and for the utilization of warm waste water for the ultimate purpose of cascade-aided energy saving. As for the proposition for recovering chemicals mainly caustic soda, it achieves environmental improvement and energy saving in the chemical industry simultaneously. (NEDO)

Research report of FY 1997 on the environmentally acceptable coal utilization system introduction support project. Demonstration project of circulating fluidized bed boiler (Jinzhou Coal-Thermal Power Corporation); 1997 nendo seika hokokusho (kankyo chowagata sekitan riyo system donyu shien jigyo). Junkan ryudosho boiler ni kakawaru jissho jigyo (Jinzhou netsuden sokoji)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

To verify the clean coal technology to be diffused in China and consolidate its diffusion basis, demonstration project of circulating fluidized bed boiler was conducted through the cooperation with China which is positive in its introduction. This report describes its characteristics. Coal and limestone are supplied in a lower part of combustion chamber, and are mixed with circulating ash by fluidized air for combustion. Densely fluidized bed the same as the bubbling fluidized bed is formed in the lower part of combustion chamber, which provides excellent stability in ignition and combustion. Particles including ash, char and limestone formed during the combustion are discharged into the cyclone through the convection heat transfer part at the outlet of combustion chamber with the combustion gas flow. Since the gas temperature is lowered to 400 to 500degC at the convection heat transfer part, troubles of the ash circulating system can be prevented. The combustion gas separated from ash at the cyclone is discharged through the heat exchanger and precipitator, and the collected ash is returned to the lower part of combustion chamber. In FY 1997, design, fabrication, procurement/inspection, field survey/meeting, survey of visitors/meeting, and education were carried out. 4 figs., 4 tabs.

Report on the fiscal 1997 result of the Japan-China joint demonstration project of environment-friendly cost utilization systems. Low grade coal combustion system (Zhejiang Huba Co. Ltd.); 1997 nendo seika hokokusho kankyo chowagata sekitan riyo system kyodo jissho jigyo. Teihin`itan nensho system ni kakawaru jissho jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This demonstration project aims at reduction of pollutants derived from coal utilization in China by demonstration of CCT to be diffused in China and preparation of diffusion bases, and stable import of energy for Japan. A low-grade coal combustion system burns low-grade coal by use of an internal circulating fluidized bed boiler which burns coal by uniform mixing and circulation of coal and some particles such as limestone and ash. Main specifications of the boiler are as follows: evaporation rate of 35t/h, steam pressure of 3.82MPa (39.0kg/cm{sup 2}), steam temperature of 450degC, water supply temperature of 150degC, internal circulating fluidized bed combustion type, boiler efficiency of 75%, and desulfurization rate of 90% or more. Main properties of low-grade coal are as follows: calorific value of 1830kcal/kg, coal size of 10mm or less, total water content of 2.5%, total S content of 2.7%, ash content of 67.7%, limestone purity of 50% or more, and stone size of 3mm or less. The results in fiscal 1997 are as follows: field survey and arrangement, basic planning and design, design, production and procurement of equipment, training, and dispatch of field supervisor. 26 figs., 3 tabs.

Fiscal 1993 international joint projects under New Sunshine Program. Surveys of bilateral cooperation and solar energy technology; 1993 nendo kokusai kyoryoku jigyo nikokukan kyoryoku taiyo energy gijutsu ni kakawaru gijutsu chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Concerning bilateral projects, overseas surveys were conducted about Japan-Australian and Japan-US technical cooperation. Concerning technological development, information was collected at the Solar World Congress of the International Solar Energy Society (ISES), and information was collected and opinions were exchanged at the 15th International Conference on Amorphous Semiconductors. A survey was conducted of Russia's development of solar cells and of their performance evaluation, and an overseas survey was conducted of the development of spaceborne photovoltaic power generation system practicalization technology. Surveys were conducted of international joint projects for the development of photovoltaic power generation system practicalization technology in Europe and the US. Overseas surveys were conducted of international joint projects concerning the development of photovoltaic power generation system practicalization technology, and a survey was conducted of the research and development of photovoltaic power generation in the US and of the state of introduction and diffusion of the same. A survey was also conducted of the state of element technology development for solar energy utilization in Europe. (NEDO)

FY 1998 annual report on the solar energy technology research and development working group. 19th R and D activity report; 1998 nendo taiyo gijutsu bunkakai. Dai 19 kai jigyo hokokukai

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

Summarized herein are the FY 1998 R and D activities by the solar energy R and D working group, extracted from the 19th R and D activity report by NEDO. Mr. Kadoi, a NEDO's director, gave a lecture titled (Expectation on and problems involved in power generation by solar light and wind power), and Mr. Kamon, a managing researcher of NEDO's solar technology development group, reported (Technological development trends of solar technology development group). The other topics reported by the individual groups include development of large-size wind power generation systems, development of techniques for increasing throughputs of high-efficiency, large-area amorphous solar cells, development of techniques for manufacturing high-reliability CdTe solar cell modules, development of techniques for manufacturing CIS solar cell modules, analysis/assessment of thin-film silicon-based solar cells, development of processes for manufacturing silicon of rationalized energy use, R and D of (new multi-layer structure) modules assembled into building materials to form monolithic structures, and development of techniques for manufacturing amorphous thin-film polycrystalline silicon hybrid thin- film solar cells. (NEDO)

Research report of fiscal 1997. Invitation project of specialists on petroleum substituting energy between Japan and the EU; 1997 nendo chosa hokokusho. Nichi EU sekiyu daitai energy kanren senmonka shohei jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Specialists were invited from EU countries for information exchange to promote R and D of petroleum substituting energy in Japan. In the seminar on the present and future trend of R and D of fuel cells in EU countries, the present R and D state of fuel cells in Italy, the present state and future R and D plan of fuel cells in ANSALDO group, the state of SOFC R and D in Germany and by international cooperation, and R and D of polymer electrolyte fuel cell in Fraunhofer institute for Solar Energy Systems were reported contributing to mutual understanding between Japan and the EU. Exchange of opinions and information was also made between 4 fuel cell specialists of EU countries and Japanese specialists. The report on such an exchange includes the outline of Japanese fuel cell technologies, and the present R and D states of phosphoric acid fuel cell (PAFC), molten carbonate fuel cell (MCFC), solid oxide fuel cell (SOFC), and polymer electrolyte fuel cell (PEFC). The specialists visited some government organizations, semi-government organizations, institutes and private enterprises related to promotion, support and verification of R and D of fuel cells. 2 tabs.

Joint research achievement report on field test project for photovoltaic power generation of industrial use in fiscal 2000; 1999 nendo sangyo tou you taiyokohatsuden field test jigyo kyodo kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-05-01

This paper summarizes the achievements in fiscal 2000 on the field tests for photovoltaic power generation of industrial use. This report describes the details of the achievements of the field tests in 36 locations including the following organizations: the Japan Industrial University, a school juristic person; the Harukawa Gakusha, a school juristic person; the Snow Brand Dairy; the Sony Chemicals; the West Japan Passenger Railways; the Hokushin Welfare Society, a social welfare juristic person; the Seikyou Gakuen, a school juristic person; the Miko Corporation; the Akashi Apparel Corporation; Shigenobu Township in Ehime Prefecture; the Japan Ham; the Seiko Epson; Henri Charpantier Corporation; the Joyo Gakuen, a school juristic person; Matsushita Electric Industry; Nio Township in Kagawa Prefecture; Matsumae Township in Ehime Prefecture; Nakajima Township in Ehime Prefecture; Sugo Gakuen, a school juristic person; the East Japan East Japan Passenger Railways (General Training Center); Shizuoka Automobile Gakuen, a school juristic person; Tomiyama Village in Aichi Prefecture; Futamura Grinding Industry; Toba City in Mie Prefecture; Higashi-ura Township in Hyogo Prefecture, Taisho Township in Kochi Prefecture; the Nagasaki Branch Office of the West Japan Telegraph and Telephone Company; Ashikita Township in Kumamoto Prefecture; the Miyazaki Branch Office of the West Japan Telegraph and Telephone Company; Oi Township in Fukui Prefecture; the Keishin Society, a social welfare juristic person; the Azabu Veterinarian School, a school juristic person, Omiya Township in Ibaraki Prefecture; and the Showa Electric Machinery. (NEDO)

Report on the project for working out the new energy vision of the Kamoto Town area. Feasibility study; 2001 nendo Kamoto machi chiiki shin energy vision sakutei tou jigyo fijibiriti hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-02-01

For the realization of 'the introduction of biomass of animal manure/garbage,' an important item in 'the new energy vision of the Kamoto Town area (Kumamoto Prefecture),' a feasibility study was conducted. For the resource retrieval of animal manure, etc., only composting is generally conducted. In this project, however, two projects are combinedly conducted: project for producing biogas (main component: methane gas) and liquid fertilizer and project for producing compost. The project pursues the reduction in running cost by self-sufficiency of energy and the environmental preservation by recovery of methane gas. The plant for producing biogas and liquid fertilizer consists of garbage crusher, storage tank, anaerobic fermentation tank and generator. The plant for producing compost consists of solid liquid separator, fermentation tank, agitator and smell remover. In the feasibility study, the following were carried out: study of the establishment of specifications/selection of the necessary conditions for a plant tentatively named the Kamoto Town Biomass Center, study of the proposed site for plant, survey of the financial plan, survey of the operational system, study of the project promotion system, etc. (NEDO)

FY 1998 annual report on the solar energy technology research and development working group. 19th R and D activity report; 1998 nendo taiyo gijutsu bunkakai. Dai 19 kai jigyo hokokukai

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

Summarized herein are the FY 1998 R and D activities by the solar energy R and D working group, extracted from the 19th R and D activity report by NEDO. Mr. Kadoi, a NEDO's director, gave a lecture titled (Expectation on and problems involved in power generation by solar light and wind power), and Mr. Kamon, a managing researcher of NEDO's solar technology development group, reported (Technological development trends of solar technology development group). The other topics reported by the individual groups include development of large-size wind power generation systems, development of techniques for increasing throughputs of high-efficiency, large-area amorphous solar cells, development of techniques for manufacturing high-reliability CdTe solar cell modules, development of techniques for manufacturing CIS solar cell modules, analysis/assessment of thin-film silicon-based solar cells, development of processes for manufacturing silicon of rationalized energy use, R and D of (new multi-layer structure) modules assembled into building materials to form monolithic structures, and development of techniques for manufacturing amorphous thin-film polycrystalline silicon hybrid thin- film solar cells. (NEDO)

Fiscal 1993 international joint projects under New Sunshine Program. Surveys of bilateral cooperation and solar energy technology; 1993 nendo kokusai kyoryoku jigyo nikokukan kyoryoku taiyo energy gijutsu ni kakawaru gijutsu chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

Concerning bilateral projects, overseas surveys were conducted about Japan-Australian and Japan-US technical cooperation. Concerning technological development, information was collected at the Solar World Congress of the International Solar Energy Society (ISES), and information was collected and opinions were exchanged at the 15th International Conference on Amorphous Semiconductors. A survey was conducted of Russia's development of solar cells and of their performance evaluation, and an overseas survey was conducted of the development of spaceborne photovoltaic power generation system practicalization technology. Surveys were conducted of international joint projects for the development of photovoltaic power generation system practicalization technology in Europe and the US. Overseas surveys were conducted of international joint projects concerning the development of photovoltaic power generation system practicalization technology, and a survey was conducted of the research and development of photovoltaic power generation in the US and of the state of introduction and diffusion of the same. A survey was also conducted of the state of element technology development for solar energy utilization in Europe. (NEDO)

FY 2000 report on the project for promotion of clean coal technology. Survey of zero emission coal technology; 2000 nendo clean coru technology suishin jigyo. Zero emission coru technology chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The paper surveyed a plan on the zero emission coal technology including up to CO2 fixation which is proposed in the U.S. and the present situation of the related study, and studied the viability of this plan including the R and D similar to this plan in Japan. Los Alamos National Laboratory in the U.S. thought of a concept of the technology to produce hydrogen from coal and recover CO2 at the same time for underground fixation, and is proceeding with the practical application. The process does not need oxygen, combustion, nor heating to be newly made. What is needed except coal is only water and lime, both of which can be recycled. The process, which discharges nothing into the air, is a closed cycle. The HyPr-RING process in Japan is a technology to decompose coal in high temperature (about 650 degrees C)/high pressure (100-200 atm) water for hydrogen formation, absorbing the formed CO2 by CaO, etc. Both of the processes have the problem, but it is necessary to make information exchanges since Japan and the U.S. devised the process at the same time. (NEDO)

International research cooperation in fiscal 1997. Report on the results of researches for the development of tribo-materials; 1997 nendo kokusai kenkyu kyoryoku jigyo. Tribo material no kaihatsu chosa seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Researches were conducted for the development of tribo-materials for the improvement of energy efficiency for equipment with slide members usable for example aboard automobiles, and the result is reported for fiscal 1997. In the research for the creation of substrate materials, some metals different in hardness, iron-base materials, titanium-base materials, etc., were selected, and experiments were conducted to disclose the effect of the substrate hardness/surface roughness on the critical load under which gas phase coatings fracture. In the research about surface treatment, the arc ion plating method is employed to produce TiN coatings on substrates of SKD11 and Ti-6Al-4V, and the critical loads were evaluated using a heavy duty, acoustic detection type adhesion evaluator and a sliding wear tester. Furthermore, the substrate/coating interface is subjected to observation under high-resolution transmission electron microscope. As for the evaluation of coating characteristics, the effects of the hardness of the coating itself, Young`s modulus, and toughness on the fracture of the coating were investigated. During the international joint researches, information was exchanged with National Institute for Standards and Technology, U.S. 11 refs., 64 figs., 4 tabs.

Fiscal 2000 survey report on overseas geological structure, etc. Project for exchanging experts - Exploration technology (Indonesia); 2000 nendo kaigai chishitsu kozo to chosa hokokusho. Gijutsusha koryu jigyo - Tansa gijutsu bunya (Indonesia)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the stabilization of coal supply/demand in the APEC (Asia-Pacific Economic Cooperation Conference) region and for the stable supply of coal to Japan, Japanese engineers and experts were dispatched to Indonesia, where coal production was remarkably increasing and efforts were being actively exerted to develop new coal mining fields, for training Indonesian specialists there, and Indonesian specialists were invited to Japan for training here. Japanese instructors on dispatch delivered lectures on coal geology, exploration, and exploitation at the human resource development center of Bandung City during the period July 20 through August 4, 2000, which was followed by a coal outcrop survey training session in the field. The trainees were from Kalimantan, Sumatra, Java, etc., and numbered 30. The trainees invited to Japan received lectures and training related to coal geology, exploration, and mining programs during the period October 19 through November 18, 2000, at the Geological Survey of Japan, Agency of Industrial Science and Technology, Ministry of International Trade and Industry; Matsushima Coal Mining Co., Ltd.; Enzan Plant, Tone Corporation; DIA Consultants Co., Ltd.; and Mitsubishi Materials Corporation. (NEDO)

Report on the project for working out the new energy vision of the Chinen Village area in FY 2001; 2001 nendo Chinen son chiiki shin energy vision sakutei tou jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-02-01

For the purpose of promoting the introduction of new energy and enhancing the awareness of it in Chinen Village, Okinawa Prefecture, an investigational study was conducted of the trend of energy consumption of the village, existence amount of new energy, case study for new energy introduction, etc., and a vision was worked out. The energy consumption amount of Chinen Village in FY 1999 was estimated at 591,935 x 10{sup 3} MJ/y. By sector, the consumption amount in the transportation sector was the highest, approximately 40%, followed in order by the household sector, business sector and industrial sector. The rate of energy source was 49.2% of petroleum, 42.3% of electric power and 8.5% of gas. As the case study for new energy introduction, the following were studied: introduction of photovoltaic power generation to the village office/Azama Sun Beach/hydroponics/JA branch office/prawn farm, introduction of photovoltaic power generation/wind power generation to the village gymnasium/village drainage pump/refrigerating facilities of the fisheries cooperative association, etc. Further, as the new project, the following were studied: introduction of photovoltaic power generation/wind power generation to the agricultural irrigation project/comprehensive sports park, introduction of photovoltaic power generation to the new building of Chinen Elementary School/maker of processed medicinal herbs. (NEDO)

FY 2000 report on the promotion projects by Research Institute of Innovative Technology for the Earth. Proceedings of the international seminar (Reports presented to the international workshop for selective oxidation catalysts); 2000 nendo chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo kokusai seminar jigyo shiryo. Sentaku sanka shokubai kokusai workshop hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the FY 2000 results of the international workshop for selective oxidation catalysts, promoted by RITE. The session of methane activation includes a comprehensive lecture on designs of selective alkane oxidation catalysts developed since the 1980s, describing the simplified catalyst design procedures and, at the same time, pointing out the vapor-phase reactions governing the overall reactions at high temperature. The session of alkane oxidation includes a lecture on oxidation of ethane into acrolein in the presence of a silica catalyst supporting isolated active sites, stressing necessity for controlling the vapor-phase reactions and importance of isolating the active sites. The session of crystalline materials includes a lecture on Ti-siting in Ti-containing molecular sieve and selective oxidation catalyst functions, concentrating discussion on oxidation with H{sub 2}O{sub 2} as the oxidant on TS-1. The session of engineering hybrid includes a lecture on catalytic partial oxidation of alkanes in millisecond reactors, describing that possibility of controlling the vapor-phase reactions in the presence of monolith, porous-plate catalysts in a reactor through which the reactant gases pass in a very short time, of the order of millisecond. (NEDO)

FY 2000 report on the survey project on potentiality of the environmental harmony coal utilization system. Potential study of the circulating fluidized bed boiler model project in Vietnam; 2000 nendo kankyo chowagata sekitan riyo system kanosei chosa jigyo hokokusho. Vietnam ni okeru junkan ryudosho boiler model jigyo jisshi kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In Vietnam, survey was conducted of the project in which the adoption of circulating fluidized bed boiler (CFB) makes energy conservation and greenhouse effect gas reduction possible. CFB makes a marked decrease in SOx emission possible by using limestone as combustion bed material. As a result of the survey, the thermal power plant was not suitable for the model project due to its large size. However, it was found that two cement plants and one fiber plant having coal-fired boiler were suitable for survey. Nghi Son and Bim Son cement plants are typical cement plants in Vietnam. As a result of the hearing, they were eager to adopt CFB equipment. As to environmental improvement effects, in the thermal power plant with power source loads, emissions of SOx and NOx can be reduced by 79.0% and 72.5%, respectively. Further, in Nam Dinh Textile Company, emissions of SOx and NOx can be reduced by 79.8% and 84.6%, respectively, in case of converting boiler from the existing stoker boiler to CFB boiler. (NEDO)

Project report for fiscal 1998 on the research cooperation promotion project/research cooperation related to practical use of a thermal efficiency enhancing system for use in thermal power plants; 1998 nendo kenkyu kyoryoku suishin jigyo / karyoku hatsudensho ni okeru netsu koritsu kojo system no jitsuyoka ni kansuru kenkyu kyoryoku jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Thermal efficiency enhancing system technology for existing thermal power plants is studied jointly with Indonesia to achieve energy conservation and power generation cost reduction and serve for suppressing CO2 emission. Site investigations were carried out for the study on enhancing thermal efficiency in component devices, including improvements in a device to rinse small pipes in condensers and in materials used in air preheaters, as well as for heat management and efficient operation of the plants. Indonesian engineers were received to develop device designing and thermal efficiency controlling programs, and for technical guidance. Site seminars were held to proliferate the achievements. Under the trend of increasing electric power demand, Indonesia is apt to place first priority on stabilized operation of power plants, with the efforts of thermal efficiency management staying behind partly due to fossil fuel price being low. The present project has made it possible to utilize hereafter the result of the rough design on improving the thermal efficiency in existing thermal power plants as has been done under the present project. Receiving the researchers and holding the site seminars also helped transfer the technologies on the thermal efficiency improving processes, and device maintenance and management methods. The project has also contributed to the consciousness reformation. (NEDO)

Report on achievements in proliferation project to introduce environment harmonizing type coal utilization system in fiscal 1998. Joint demonstration project for CMG recovery and utilization system in fiscal 1998; Kankyo chowagata sekitan riyo system donyu shien nado fukyu taisaku jigyo. 1998 nendo CMG kaishu riyo system kyodo jissho jigyo seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

This paper describes the discussion report for fiscal 1998 on the CMG (coal methane gas) recovery and utilization project to be implemented from fiscal 1998 through fiscal 2002 at Tiefa Mining Bureau of Liaoning Province in China. The Daixing mine was selected as the survey object. The introduced technologies and facilities include test drilling for degassing (medium measure horizontal degassing of 300-m class), induction from degassing holes, fly ash sealing, sealed gas degassing, surveillance and control technologies and facilities. The recovered gas is to be supplied to the cities of Tiefa and Tieling as town gas, for which compressed gas feeding and controlling technologies and facilities will be introduced. This paper lists the gush-out quantity (1,000 Nm{sup 3}), the recovery quantity (1,000 Nm{sup 3}), the recovered gas concentration (%), the utilization quantity (1,000 Nm{sup 3}), and the utilization rate (%). The figures for the respective items before and after the implementation are 128366, 32949, 44.5, 7000, 5, 123500, 43890, 49.1, 39826, and 32. The quantity of gas gushing out at facings decreases in association with increase in the recovered gas quantity, whereas the gas concentration at facings in the Daixing mine in 2003 is estimated to decrease to 0.1%, contributing to safe mining operation. The test drilling for medium measure horizontal degassing expands the degassing assured scope per one test drilling seat, and can reduce the total test drilling length and construction amount. (NEDO)

FY 1998 Report on development project of structural residence of the next generation. Attachment 4. Frame analysis system manual; 1998 nendo jisedai kozo jutaku kaihatsu jigyo shiryohen. 4. Kako kaiseki system manual

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Attachment 4 of the FY 1998 report on development project of structural residence of the next generation describes the frame analysis system manual. NAPISOS is a program for analyzing static and dynamic responses of three-dimensional structures. The dynamic response is calculated by numerical integration in the time region. Dynamic load can handle dynamic exciting force, uniform seismic input and forced displacement at a node, and analyze linear elasticity and non-linear properties. The static load can handle nodal force, static seismic coefficient and forced displacement at a node, and analyze linear elasticity and non-linear properties. The static analysis also can perform analysis based on the time history response displacement method as the special case. The program implementation procedures fall into 4 general steps; first: inputting/processing of structural data, second: eigen value analysis or equivalent nodal force calculation, third: response calculation by direct integration, preparation of equivalent damping matrix or pre-stress analysis, and fourth: outputting the results. The input data related to control, structure and load are also described. (NEDO)

Report of a project for the technical development of the environmental preservation and resource effective utilization system in fiscal 1995; 1995 nendo kankyo hozen shigen yuko riyo system gijutsu kaihatsu jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The paper outlined the present situation of industrial waste all over Japan and the present situation of industrial waste of large urban areas where it is most difficult to secure places for the final disposal, and conducted an analysis on the present and future amount of final disposal waste. According to the literature from the Ministry of Health and Welfare, `research report on the discharge/treatment situation of the industrial waste` and `research results of administrative organizations for industrial waste,` the situation of final disposal from the past to the present was outlined and analyzed to study the future trend. Out of the administrative divisions of Japan, four divisions, which are all typically called large urban areas, were selected, and the situation of industrial waste in large urban areas was outlined and analyzed according to the questionnaire survey and the literature on industrial waste obtained from each administrative division. The survey by the Ministry of Health and Welfare indicated that the volume of the industrial waste discharged from the whole country amounted to approximately 400 million tons in fiscal 1992. However, helped by the improving recycling of waste construction materials, the amount of final disposal around 2000 is presumed to be less by 20% or so than that in 1992. 58 refs., 5 tabs.

Fiscal 1998 research report. Popularization project of the proper treatment technology of industrial wastes in Asian regions; 1998 nendo chosa hokokusho. Asia chiiki sangyo haikibutsu tekiseika shori gijutsu nado fukyu sokushin jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Study was made on popularization of the proper treatment technology of industrial wastes in Asian regions. In principle, industrial wastes should be recycled in a country concerned, however, because of a difference in technology and industrial location, treatment of all industrial wastes in a country concerned is impossible. International cooperation is thus indispensable to promote proper efficient practical measures for environment. For studying the possibility of the international cooperation between Japan and Asian countries concerned for further recognition and solution of industrial waste problems, 'International Symposium on the Asian Industrial Waste Issue' have been held in Tokyo since 1997 for governmental staffs. In fiscal 1998, Malaysia was invited in addition to China, Philippines and Thailand for popularization of the proper treatment and recycling of industrial wastes in Asian regions. In every Asian countries, poor collection of discharge, treatment and disposal data is an obstacle to effective treatment. Technical cooperation and financial support by developed countries are demanded. (NEDO)

Fiscal 2000 survey of geological structures overseas. Exchange of engineers with Indonesia (Coal mining technology); 2000 nendo kaigai chishitsu kozo nado chosa hokokusho. Gijutsusha koryu jigyo (tanko gijutsu bun'ya) Indonesia

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Indonesia rich in coal resources consumed 70-million tons of coal in 1999, which covered 17% of its total energy demand. It is estimated that as much as 120-million tons will be produced in 2005, and it is expected that underground mining will increase. Under such circumstances, Indonesia strongly desires that Japan's underground mining technologies be transferred to Indonesia. For the transfer of technologies especially involving production control and management out of Japan's underground mining technologies, Japan dispatched engineers to Indonesia under a mining engineer exchange project, and received and trained Indonesian engineers. Under the engineer exchange project, five engineers were dispatched to Indonesia and gave lectures and on-site training in the period July 9 through August 5, 2000. Japan received seven engineers, who were given lectures and training at the Ikeshima mining field of Matsushima Coal Mining Company in the period November 12 through December 12, 2000. (NEDO)

FY 1999 report on the results of the model project for facilities for effective utilization of paper-manufacturing sludge, etc.; 1999 nendo seika hokoku. Seishi surajji tou yuko riyo setubi moderu jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of contributing to the reduction in the energy consumption in the paper/pulp industry which is an industry of much energy consumption in Indonesia and to the stable energy supply in Japan, a model project for facilities for effective utilization of paper sludge, etc. was carried out, and the FY 1999 results were reported. Concretely, the paper sludge and solid waste discharged from the paper-manufacturing process are to be incinerated in self-combustion in fluidized bed incinerator. Further, the remaining heat is to be recovered as steam from the combustion exhaust gas for the effective utilization within plant. This verifies the reduction in energy consumption and reduction in emission of greenhouse effect gas. Activities for spread of the said facilities are to be made in Indonesia. The site for this project is FSW located in Bekasi, West Jawa. This is a private paper company which manufactures cardboard use paper of 0.5 million t/y using used paper as raw material. In this fiscal year, instructors were sent to FSW for installation/construction work according to the basic agreement and the attachment to the agreement. (NEDO)

Fiscal 1999 technical survey report. Basic survey for energy consumption rationalization and cooperative project on energy conservation seminar; 1999 nendo energy shohi koritsuka kiso chosa oyobi sho energy seminar kyoryoku jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-06-01

A survey was conducted of Myanmar's energy-consuming industries for exploring the feasibility of introducing practical energy conservation techniques and facilities to this country and for collecting basic data for the implementation of the project in the future. On the other hand, some lecturers were dispatched to an energy conservation seminar which was held in cooperation with the Government of Myanmar. Visited during the basic survey were (1) the Kyan Gin plant of Myanmar Ceramic Enterprise representing Myanmar's cement making industry, (2) the Thanlyin plant of Myanmar Petrochemical Enterprise representing Myanmar's oil refining industry, and (3) the Siftong plant of Myanmar Paper and Chemical Enterprise representing Myanmar's paper making industry. In the study of energy conservation measures for which stabilization of operation through reinforced facility maintenance and management were required, it was concluded that much time was necessary before Japan's advanced energy conservation technologies might be introduced into Myanmar. Three to six propositions were presented to each of the three plants. At the seminar, the importance of energy conservation promoting measures and the results of the basic survey were introduced to the audience. A lecture meeting was also held to familiarize some participants with NEDO-DB (Database of New Energy and Industrial Technology Development Organization). (NEDO)

Fiscal 1998 survey report. Assessment and analysis of collected data in wind power generation field test project; 1998 nendo furyoku hatsuden field test jigyo ni okeru shushu data hyoka kaiseki chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Examination was made on wind conditions, power generating characteristics, and the reliability of a system by analyzing the operation record of the wind power generation equipment which was installed at Hiraizumi-cho, Nishi-Iwai gun, Iwate prefecture and at Misaki-cho, Miura-shi, Kanagawa prefecture. The equipment at Hiraizumi had a rated output of 490 kW, and at Miura 400 kW. The period of the examination was from April, 1998 through February, 1999, the items for data collection being the generator output, generated energy, average wind velocity, record of abnormality occurrence, and maximum wind velocity. At Hiraizumi, annual average utilization rate was 12.9%; annual average operation rate, 49.9%; average wind velocity, 4.6 m/s; and maximum wind velocity of the period, 31 m/s. At Miura, annual average utilization rate was 16.5%; annual average operation rate, 77.0%; and average wind velocity, 5.0 m/s. The utilization rate is desirably 17%. The top three abnormalities were drop in AC control voltage, actuation of main shaft brake and eddy current/actuation of open phase relay, accounting for 83.3% of the total abnormalities at Hiraizumi, while they were unbalance in current, grid drop and automatic unwinding of cable, accounting for 74.5% at Miura. (NEDO)

Report on the survey of the commercialization of wood biomass energy. Project on the production of wood pellet fuel; 2001 nendo mokushitsu baiomasu energy jigyoka chosa hokokusho. Mokushitsu peretto nenryo seizo jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-02-01

For the purpose of regenerating forestry and contributing to the policy for prevention of global warming, a potential study was made of the commercialization of the wood pellet using low-quality wood materials such as thinnings and wood pieces from lumber mill. In the study, based on the survey of raw materials of wood pellet and the demand amount, the scale of pellet production was assumed, and subjects were arranged toward the basic design of plant, evaluation of economical efficiency and commercialization. As a result of the study, the following subjects were extracted. In the study, the supply of lumbers of 2,800 t/y and securing of demand of about 1,600 t/y were set forth as a premise, but the subject was to secure the initial demand. The pellet combustor was higher in price than the kerosene combustor, and for the imported combustion equipment, the combustion of white pellet was supposed. It is necessary to develop combustor of pellets including the bark. In the trial calculation of the unit price of heat utilization (yen/Mcal), the pellet stove was about 3.3 times as high in price as the kerosene stove. It is necessary to reduce the pellet price down to 30 yen/kg or so by decreasing the cost of pellet production. (NEDO)

FY 1998 annual report on the hydrogen, alcohol and biomass technology working group. 19th R and D activity report; 1998 nendo suiso alcohol biomass gijutsu bunkakai. Dai 19 kai jigyo hokokukai

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

Summarized herein are the FY 1998 R and D activities by the hydrogen, alcohol and biomass technology working group, extracted from the 19th R and D activity report by NEDO. Mr. Murase, a NEDO's director, outlines R and D of techniques for hydrogen-utilizing international clean energy systems, high-efficiency power generation by wastes, reutilization of combustible wastes as fuels, high-efficiency clean energy vehicles and pioneer techniques for utilization of supercritical fluids, and commercialization of waste water treatment techniques for prevention of global warming, in the report entitled (General situations of the hydrogen, alcohol and biomass technology development group). The researchers presented the R and D results of development of externally circulating type fluidized bed, demonstration tests therefor by a pilot plant, phase 1 WE-NET project, phase 1 hydrogen-fueled turbine, phase 1 closed type high-efficiency gas turbine system equipped with a CO2 recovery system, and simple systems for cleaning up industrial wastes. (NEDO)

Report on fiscal 1995 project to promote an exchange of researchers on environmental problems in the Asia-Pacific region; 1995 nendo itakujigyo (Asia/Taiheiyo chiiki kankyo mondai kenkyusha koryu sokushin jigyo hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

For the purpose of solving environmental problems caused in association with the increasing industrial activities in the Asia-Pacific region, the construction of a research network is being advanced aiming at promoting exchanges with researchers of other countries and activating information exchanges. Investigators were sent overseas to grasp the present situation, and researchers participated in a symposium on the APEC environmental technology cooperation for mutual understanding and personal interchange. In the overseas survey, visits were paid mainly to national research institutes and universities in India and Thailand. Positive approval was obtained on the construction of the ETERNET APR (Environmental Technology Research Network in the Asia-Pacific Region). In the symposium on the APEC environmental technology cooperation held in Nagoya, researchers participated mostly in the second session and made earnest discussions with researchers from other countries. The necessity and importance of the network was emphasized. Countries which participated the symposium have problems common to each, and it was greatly significant to meet together and discuss together. The environmental problem is on a global scale, and it is necessary to make close exchange/interchange of information/opinion on a long term basis and to tackle it in the whole Asia-Pacific region. 3 tabs.

Fiscal 1998 research report. Popularization project of the proper treatment technology of industrial wastes in Asian regions; 1998 nendo chosa hokokusho. Asia chiiki sangyo haikibutsu tekiseika shori gijutsu nado fukyu sokushin jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Study was made on popularization of the proper treatment technology of industrial wastes in Asian regions. In principle, industrial wastes should be recycled in a country concerned, however, because of a difference in technology and industrial location, treatment of all industrial wastes in a country concerned is impossible. International cooperation is thus indispensable to promote proper efficient practical measures for environment. For studying the possibility of the international cooperation between Japan and Asian countries concerned for further recognition and solution of industrial waste problems, 'International Symposium on the Asian Industrial Waste Issue' have been held in Tokyo since 1997 for governmental staffs. In fiscal 1998, Malaysia was invited in addition to China, Philippines and Thailand for popularization of the proper treatment and recycling of industrial wastes in Asian regions. In every Asian countries, poor collection of discharge, treatment and disposal data is an obstacle to effective treatment. Technical cooperation and financial support by developed countries are demanded. (NEDO)

FY 2000 report on the survey project on the policy for international energy utilization rationalization, etc. - model project on the heightening of international energy consumption efficiency. Viability survey of the project on energy conservation in the urea synthesis process in India; 2000 nendo kokusai energy shiyo gorika nado taisaku jigyo - kokusai energy shohi koritsuka nado model jigyo chosa hokokusho. Indo ni okeru nyoso gosei process sho energy jigyo jisshi kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of conserving energy and reducing greenhouse effect gas, a remodeling project was studied of urea plants constructed from the 1960s to the 1970s. Conditions for being companies for study are as follows: company has a production scale of more than 0.2 million t/y, adopts the complete circulation method, and will continue operation. And, Duncans Industries Ltd. (DIL) was selected. DIL owns the ammonia plant of 3 series x 400 t/d and the urea plant of 3 series x 682 t/d. In the modeling, stripper and carbamate condenser are added to the existing reactor as the main equipment. As a result of the study, the energy conservation effect was 13,667 toe/y, and the amount of reduction in greenhouse effect gas was 42,289 t-CO2/y. The total amount of this project was roughly estimated at 1.517 billion yen. By carrying out the project, the urea production cost is reduced approximately $9/t, but the project becomes unprofitable if the urea price is based on $188.1/t. (NEDO)

Research report for fiscal 1998. Research for 'New Earth 21' project implementation program preparation; 1998 nendo chosa hokokusho. 'Chikyu saisei keikaku' no jisshi keikaku sakusei ni kansuru chosa jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For the establishment of a CO2 measures introduction scenario which the world would accept, the latest information was collected, the DNE21 (Dynamic New Earth 21) model was improved, and simulation was reviewed. In fiscal 1998, simulation was performed for each district using an LDNE21 (Linear Dynamic New Earth 21) model, and an energy flow chart, energy balance table, and trade table were prepared and subjected to detailed deliberation. Studied were also conducted about the changes to occur in methanol production when the natural gas reserves and plant cost data were given different values. In the DNE21 model, the 'macro economy model' and 'warming damage function' were integrated, and simulation was performed for verification. Using a standard model compatible with COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change), comparison was made between a case in which different CO2 emission constraints were imposed on the advanced area and developing area separately and a case in which one and the same constraint was imposed on the world as a whole, and calculations were made about CDM (Clean Development Mechanism). (NEDO)

Fiscal 1998 international research cooperation project. Feasibility study report on excavation of international joint research seeds; 1998 nendo kokusai kyoryoku jigyo seika hokokusho. Kokusai kyodo kenkyu seeds hakkutsu no tame no FS chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Feasibility study (FS) was made on excavation of international joint research seeds for developed countries. As FS themes, 6 themes were selected among applied 11 ones. China was interested in the joint research on improvement of a cetane number by ring-opening of LCO from fluid catalytic crackers through hydrogenation for Arabian crude oil, although China has an experience for domestic one. Since France and the USA are in the early developmental stage of practical atmospheric temperature and pressure conversion technology of lower hydrocarbon after the basic research stage, study was made on the possibility of a joint research. The other themes are as follows: Oil resource and energy conservation technology by recycling general plastics and industrial synthetic resins, advanced solid catalyst regulating technology by physicochemical technique and its application to next-generation oil refining processes, structure analysis of asphaltene and reaction mechanism analysis of heavy oil by computer simulation, and production technology of ultra-precisely controlled catalytic materials. (NEDO)

Achievement reports on joint research of solar energy power generation field test project in fiscal 1997. Part 1 of 3; 1997 nendo taiyoko hatsuden field test jigyo kyodo kenkyu seika hokokusho 1/3

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-08-01

This report is a collection of 101 achievement reports on joint research of solar energy power generation field test project. The contents of the achievement reports are the results and generalization of the joint research with respect to the solar energy power generation field test project. As regards the locations of executing the joint research, the locations by areas and applications are stated. By areas, the joint research was carried out on gymnasiums, parks, recreation centers in the standard areas, universities, sports facilities, public halls, agricultural associations, aged persons' homes, primary, middle and high schools, prefectural office buildings and industrial technology centers in cold districts; prefectural office buildings, agricultural associations, universities, museums, industrial technology centers in good insolation districts; museums, primary, middle and high schools, parks in strong wind and salt polluted districts; and universities and police stations in snowy districts. By applications, the joint research was performed on life cooperative halls, factories, nursery schools, hospitals, clinics, local newspaper companies, indoor warm-water swimming pools, and mushroom fields. (NEDO)

Achievement reports on joint research of solar energy power generation field test project in fiscal 1997. Part 2 of 3; 1997 nendo taiyoko hatsuden field test jigyo kyodo kenkyu seika hokokusho 2/3

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-08-01

This report is a collection of 26 achievement reports on joint research of a solar energy power generation field test project. The major contents of the achievement reports relate to the solar energy power generation field test project (summarized as manufacture and installation of solar energy power generation systems, summary of solar energy power generation facilities, peripheral devices, and daily schedule of the construction). The reports describe achievements of the joint research (names and achievements of the joint research, study presentation, lectures, literatures, status of patents, similar research in and cooperation with other research institutions), generalization of the research, and future problems. Locations of the joint research carried out are libraries, kindergartens, health and welfare centers, children's culture centers, general traffic centers, primary and middle schools, river water purifying facilities, credit banks, manufactories, retail shops at car parking areas, office buildings, hospitals, joint prefectural office buildings, municipal health centers, and prefectural general power generation control stations. (NEDO)

Report on surveys in fiscal 1998 on the project to invite petroleum substituting energy related experts in Japan and EU; Nichi EU sekiyu daitai energy kanren senmonka shohei jigyo 1998 nendo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In relation with coping with global environmental problems in recent years, needs are increasing more than ever for enhancing fossil energy utilization rates, developing and expanding utilization of petroleum substituting energies that can substitute fossil energies. Since Japan is particularly a large energy consuming country, and cannot escape from depending on import for the majority of its energy resources, it is an urgent issue to enhance the energy utilization efficiency and further promote development and utilization of new energies. To do this, it is indispensable to exchange such item of information as identification of actual status in other countries of handling the petroleum substituting energies. Taking up geothermal energy, fiscal 1998 invited four experts from EU countries. Visits were made for about two weeks on Japanese research institutes and business enterprises related to geothermal energy, and opinions and information were exchanged. A seminar was held on the final day, where the EU experts have made presentations on the current status and future prospects on geothermal research and development in EU. Greatly valuable suggestions were given for the Japan's future geothermal research and development. (NEDO)

FY 2000 project on the research cooperation for the environmental response type water resource effective utilization system; 2000 nendo kenkyu kyoryoku jigyo. Kankyo taiogata mizu shigen yuko riyo system ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of prevention of water pollution, stable water supply in the Philippines, etc., developmental study was made of a waste water treatment/water recycling system, and the FY 2000 results were summed up. In the operational study of Pilot Plant 1, for the waste water in the papermaking process of used paper recycling plant, development was studied of a waste water treatment/water recycling system. There occurred problems on minuteness, outflow, etc. of anaerobic granules, but those were caused by malfunction of SS removal equipment at plant side. The problems were solved by increasing flocculation/precipitation facilities. As to Pilot Plant 2 of which the R and D are planned to be started in April 2001, the food processing plant was surveyed for study, and SYSCORE was selected. Relating to the waste water treatment test of Pilot Plant 2, researchers of the Industrial Technology Development Institute (ITDI) of the Philippines conducted it under the guidance of the experimental data analysis. Besides, the paper carried out the training for technology spread/acceptance, technology spread seminar, support study in Japan, etc. (NEDO)

Fiscal 1996 achievement report. Development of liquid fuel conversion technology (Feasibility study project on liquid fuel conversion); 1996 nendo ekitai nenryo tenkan gijutsu kaihatsu seika hokokusho. Ekitai nenryo tenkan kanosei chosa nado jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This article comprises Part 1 on 'surveys of gas fields fit for a new methanol manufacturing process' and Part 2 'reports on overseas surveys of gas fields fit for a new methanol manufacturing process.' In Part 1, surveys are conducted on the existence, exploitation, and the actual utilization of natural gas resources, and on the status of natural gas industry related infrastructures in the Middle East. Proved natural gas reserves in Iran were 742tcf (trillion cubic feet) as of 1996-end, which was the largest in the world next to Russia. As for Kuwaiti natural gas resources, they all accompany oil production, with the proved reserves marking 52.4tcf as of 1996-end or the smallest in the Middle East. In Egypt, there were proved reserves of 20.4tcf as of 1996-end, and further existence of 30-40tcf is predicted. Proved reserves in Yemen are approximately 15tcf. Proved reserves in Oman were 30tcf as of 1996-end. It is expected that there will be a 1.4% increase in the demand for methanol for automobiles. The annual demand for methanol for power generation is 720,000 tons. In Part 2, on-site surveys of infrastructures and the like indispensable for methanol plant installation are reported. (NEDO)

Fiscal 2000 survey report on feasibility of implementing model project for energy conservation of sintering machine in China; 2000 nendo Chugoku ni okeru shoketsuki sho energy ka model jigyo jisshi kanosei chosa hokoku

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A survey was conducted on the feasibility of implementing a model project for energy conservation of sintering machines in ironworks in China. This paper explains the results of fiscal 2000. The survey was based on the assumption that the HPS (Hybrid Pelletized Sinter) process in operation at Fukuyama ironworks in Japan was to be introduced into China. This process is employed at the Fukuyama No.5 sintering plant with an area of 530 m{sup 2}, and is famous for the highly efficient energy consumption rate with the solid fuel consumption of 37 kg/t and the electric power consumption of 31 kWh/t. The technology was applied to the No.3 sintering machine (265 m{sup 2}) at Tangshan Steel. Case A refers to where only the energy conservation effect of a targeted sintering machine was considered, and Case B refers to where the productivity of the applied sintering machine is increased, with that of the others decreased. In Case A, total equipment cost was 1,977,450 thousand yen, energy conservation effect was 23,795 toe/y, economic savings was 244,000 thousand yen/y, and investment recoupment period was 7.85 years. In Case B, they were 1,977,450 thousand yen, 36,215 toe/y, 356,000 thousand yen/y, and 5.38 years, respectively. In the same token, at Wuhan Steel, Case A showed 2,447,160 thousand yen, 30,320 toe/y, 272,000 thousand yen/y, and 8.77 years; Case B showed 2,447,160 thousand yen, 31,570 toe/y, 289,000 thousand yen/y, and 8.28 years, respectively. Assuming the technological spread is over the entire China, the total energy conservation in terms of crude oil is expected to be 845,700 toe/y. (NEDO)

Fiscal 1996 achievement report. Development of liquid fuel conversion technology (Feasibility study project on liquid fuel conversion); 1996 nendo ekitai nenryo tenkan gijutsu kaihatsu seika hokokusho. Ekitai nenryo tenkan kanosei chosa nado jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This article comprises Part 1 on 'surveys of gas fields fit for a new methanol manufacturing process' and Part 2 'reports on overseas surveys of gas fields fit for a new methanol manufacturing process.' In Part 1, surveys are conducted on the existence, exploitation, and the actual utilization of natural gas resources, and on the status of natural gas industry related infrastructures in the Middle East. Proved natural gas reserves in Iran were 742tcf (trillion cubic feet) as of 1996-end, which was the largest in the world next to Russia. As for Kuwaiti natural gas resources, they all accompany oil production, with the proved reserves marking 52.4tcf as of 1996-end or the smallest in the Middle East. In Egypt, there were proved reserves of 20.4tcf as of 1996-end, and further existence of 30-40tcf is predicted. Proved reserves in Yemen are approximately 15tcf. Proved reserves in Oman were 30tcf as of 1996-end. It is expected that there will be a 1.4% increase in the demand for methanol for automobiles. The annual demand for methanol for power generation is 720,000 tons. In Part 2, on-site surveys of infrastructures and the like indispensable for methanol plant installation are reported. (NEDO)

New Sunshine Program for Fiscal 2000. International cooperative project for developing photovoltaic power system practicalization technology (General edition); 2000 nendo New sunshine keikaku. Taiyoko hatsuden system jitsuyoka gijustu kaihatsu kokusai kyoryoku jigyo (Sogoban)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Fiscal 2000 international cooperation for the research, development, and popularization of photovoltaic power systems is compiled. In carrying out international cooperation relating to the photovoltaic power generation program of IEA (International Energy Agency), etc., officers were sent to the 15th and 16th executive committee meetings, where they deliberated on plan formulation and budget making. They also participated in the activities of Task 1: Exchange and dissemination of information on photovoltaic power systems, Task 2: Operational performance and design of photovoltaic power systems and subsystems, Task 3: Use of photovoltaic power systems in stand-alone and island applications, Task 5: Design and grid interconnection of building integrated and other dispersed photovoltaic systems, Task 7: Photovoltaic power systems in the built environment, Task 8: Study on very large scale photovoltaic power generation systems in deserts and other unexploited regions, and Task 9: Technical co-operation for photovoltaic market deployment. A discussion was made on the holding of a 4th IEA photovoltaic power system executive conference. In addition, Japan-Australia and Japan-Oman bilateral cooperative projects were implemented. (NEDO)

Achievement reports on joint research of solar energy power generation field test project in fiscal 1997. Part 1 of 3; 1997 nendo taiyoko hatsuden field test jigyo kyodo kenkyu seika hokokusho 1/3

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-08-01

This report is a collection of 101 achievement reports on joint research of solar energy power generation field test project. The contents of the achievement reports are the results and generalization of the joint research with respect to the solar energy power generation field test project. As regards the locations of executing the joint research, the locations by areas and applications are stated. By areas, the joint research was carried out on gymnasiums, parks, recreation centers in the standard areas, universities, sports facilities, public halls, agricultural associations, aged persons' homes, primary, middle and high schools, prefectural office buildings and industrial technology centers in cold districts; prefectural office buildings, agricultural associations, universities, museums, industrial technology centers in good insolation districts; museums, primary, middle and high schools, parks in strong wind and salt polluted districts; and universities and police stations in snowy districts. By applications, the joint research was performed on life cooperative halls, factories, nursery schools, hospitals, clinics, local newspaper companies, indoor warm-water swimming pools, and mushroom fields. (NEDO)

FY 2000 Project of developing international standards for supporting new industries. 'Standardization of multicolor measurement'; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Multicolor no sokushoku no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the FY 2000 results of the study on and research and development of the testing methods for tones of anisotropic color materials (multi-colors) for proposing the international standard. USA has proposed the triangle colorimetry, based on the results of the visual tests with metallic paints, which is being incorporated in the ASTM standards. Germany seems to adopt the multi-angle colorimetery in the DIN standards. The FY 2000 efforts are directed to measurement of the reflection characteristics of the metallic and pearl-mica samples by a variable-angle spectrophotometer. The solid color and metallic color are being evaluated by a weather resistance tester QUV and outdoor tests, because of the anticipated different mechanisms by which they are aged. The functional test and analysis are also required to correlate the multi-color measurement results with visual evaluation results, and the preliminary tests are conducted to improve skill of the panelists. (NEDO)

Fiscal 1999 survey report. Study project concerning preparation for implementation plan of 'the new earth program'; 1999 nendo 'chikyu saisei keikaku' no jisshi keikaku sakusei ni kansuru chosa jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper reports fiscal 1999 survey of the new earth program. Toward the target of GHG (green house effect gasses) 550 ppm, sensitivity analysis using a linear DNE21 model was replenished, with model analyses made on a scenario concerning the countermeasure technologies/systems. In other words, performed were the improvement of accuracy by the renewal of data, sensitivity analysis concerning CO2 collection/processing technology and nuclear energy, analysis of the international regulation for controlling CO2 concentration under 550 ppm in the air in the year 2100, and sensitivity analysis on increase in per capita energy demand in Asia. Overall assessment of global warming problems was upgraded for the purpose of enabling the assessment from the consumption maximization point of view, taking into consideration cooling effects of SOx and economic growth. Potentiality assessment in rational use of energy was reexamined because energy conservation played an important role. That is, in DNE model, the data were examined of OECD signatories and developing countries from 1970s concerning natural gas, petroleum, coal and electric power, with the long-term cost flexible value estimated. In addition, feasibility was assessed of rational use of energy from energy GNP unit. (NEDO)

Basic investigation on promotion of joint implementation in fiscal 2000. Project for modification of Pridneprovskaya power plant in Ukraine; 2000 nendo kyodo jisshi nado kiso chosa hokokusho. Ukraine Pridneprovskaya hatsudensho kaishu jigyo keikaku

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With objectives of saving energy and reducing greenhouse gas emission at the Pridneprovskaya power plant in Ukraine, a scrap and build project has been discussed. This project will abolish the unit No.12 among the eight units in the existing coal burning power generation facilities, and install a natural gas burning combined cycle plant comprising of three units each with an output of 100 MW. The new plant facilities will consist of gas turbines, steam turbines, HRSG and auxiliary devices, and an air-cooled synchronous power generator with a capacity of 119 MVA. Use of natural gas as fuel reduces generation of soot, sulfur oxides, nitrogen oxides, and CO. In addition, the hot effluent and waste liquor effluent will decrease from those at the present plant. The required fund will be 30,107 million yen. The energy saving effect of this project is reduction of about 7.5 million tons of crude oil equivalent as a total in 40 years. The greenhouse effect gas will decrease by about 39 million tons as a total in 40 years. The profitability estimation calls for the number of investment recovery year of 16 years, and internal profit rate of 7.32%, wherein the implementation of the project cannot be expected as a project to be carried out by private funds. (NEDO)

Achievement reports on joint research of solar energy power generation field test project in fiscal 1997. Part 3 of 3; 1997 nendo taiyoko hatsuden field test jigyo kyodo kenkyu seika hokokusho 3/3

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-08-01

This report is a collection of 40 achievement reports on joint research of a solar energy power generation field test project. The major contents of the achievement reports relate to the solar energy power generation field test project (summarized as manufacture and installation of solar energy power generation systems, summary of solar energy power generation facilities, status of installation of solar cells, peripheral devices, and daily schedule of the construction). The reports describe achievements of the joint research (names and achievements of the joint research, study presentation, lectures, literatures, status of patents, similar research in and cooperation with other research institutions), generalization of the research, and future problems. Locations of the joint research carried out are hospitals, township hospitals, a science hall for youths, study and educational cities, primary schools, middle schools, high schools, universities, senior health centers, a life cooperative association, retails shops, factories, office buildings, joint governmental office buildings, Shinkansen stations, prefectural industrial testing centers, health and welfare centers, FM broadcasting studios, a town operated hall of technologies, prefectural office buildings and training centers. (NEDO)

FY 1998 annual report on the project of basic survey for improving energy consumption efficiency in developing countries / invitation of engineer trainees from developing countries (Indonesia, the Philippines, Vietnam and Myanmar); Hatten tojokoku energy shohi koritsuka kiso chosa nado jigyo / hatten tojokoku gijutsusha shohei jigyo 1998 nendo chosa hokokusho (Indonesia, Philippines, Vietnam, Myanmar)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

NEDO is positively implementing the training programs, in view of importance of training experts on (energy-saving and environmental conservation technologies), by inviting administrators and engineers from developing countries to educate them with Japan's pollution preventive techniques, administration procedures, energy-saving measures, and so on. In FY 1998, NEDO commissioned the International Center for Environment Technology Transfer to train administrators and engineers from Indonesia, the Philippines, Vietnam and Myanmar. This paper describes the proposals, based on the collected answers of the trainees to the questionnaires. The trainees were interested in all themes. About 40% of the trainees considered that the training period was short. Some trainees hoped the training course was held in summer. Difference in industrialization is reflected in difference in recognition and urgency of the environmental problems. Training was conducted by English and Vietnamese, but could be done without translators of Vietnamese. Preparation for the invitation needs a lot of works, and the course should be explained more thoroughly beforehand. It is regrettable that one trainee from Indonesia was late for the course. (NEDO)

FY 1998 annual summary report on project for international energy consumption rationalization. Survey on analysis tool for improving efficiency of Asian energy consumption (data book 2 for 1985); 1998 nendo kokusai energy shiyo gorika nado taisaku jigyo chosa hokokusho. Asia energy shohi koritsuka bunseki tool chosa jigyo (shiryoshu 2 1985 nen data)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The data book is compiled, based on common industrial classifications, as the tool for analyzing, e.g., the mutual ripple effects of economic growth and increased efficiency of energy consumption throughout the Asia-Pacific region. This book summarizes the industrial-related and energy-related tables for 8 Asian countries and Japan. The book II is for the 1985 data (1987 data for China), comparing with the book I for the 1990 data. The industry-related tables are composed of the tables for transaction bases, input coefficients, final demand converters, importation coefficients, inverse matrices, sensitivity/influence coefficients, production inducement levels, production inducement coefficients, degrees of dependence on production inducement, importation inducement levels, importation inducement coefficients, and degrees of dependence on importation inducement. Energy-related tables are composed of the tables for, e.g., energy input, energy consumption, emissions, and CO2 emissions. (NEDO)

FY 2000 report on the promotion projects by Research Institute of Innovative Technology for the Earth. Proceedings of the international seminar (Reports on photosynthetic CO2-assimilating enzymes by the international workshops); 2000 nendo chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo kokusai seminar jigyo shiryo. Kogosei CO2 kotei koso kokusai workshop hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the reports on photosynthetic CO2-assimilating enzymes, presented to the international symposium. These enzymes are important for assimilating CO2 in air, maintaining the environments and production of foods. For genes and proteins, the topics include diversification and function evolution of the RuBisCO (ribulose 1,5-bisphosphate carboxylase/oxygenase) in the natural environments, in particular in microorganisms. For activity regulation of PEPC, the topics include three-dimensional structures of PEPC and phosphorylation mechanisms and activity regulation therefor. For activity regulation of RuBisCO, the topics include post-translational activity of the enzymes (e.g., methylated enzyme); molecular regulation mechanisms involved in the biosynthesis and decomposition of RuBisCO; and activity regulation mechanisms in the chloroplast. For leaf photosynthesis and RuBisCO, the topics include importance of enzymes and involved in-vivo reaction steps for leaf photosynthesis CO2 assimilation reactions. For function of PEPC, the topics include the biochemically and molecular biologically necessary and sufficient conditions for the C4 mechanism as the special photosynthesis mechanism. For transgenic approaches, the topics include procedure for allowing the RuBisCO gene of a dissimilar organism to function in the tobacco chloroplast, and introduction of enzymes involved in the C4 photosynthesis pathway in C3 plants. (NEDO)

Fiscal 1998 intellectual infrastructure project utilizing civil sector functions. Research and development project on prompt-effect type intellectual infrastructure creation (Basic study of measurement of human characteristics); 1998 nendo minkan no kino wo katsuyoshita chiteki kiban jigyo seika hokokusho. Sokkogata chiteki kiban sosei kenkyu kaihatsu jigyo (Ningen tokusei keisoku ni kansuru kiban kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the development of working conditions fit for aged people and devices for them to operate, their visual function and behavioral characteristics are measured and analyzed. In the study of visual functions, 50 people from local cities and regions and another 50 from Osaka and its neighboring cities are subjected to measurement regarding visual acuity required in daily life, color discrimination, dark adaptation, glare, and the like. In the study of performing characteristics, 500 people are subjected to measurement regarding the scope of movement of upper limbs, their reach, and skillfulness with which the people can move fingers. When brightness, luminance, and contrast are caused to change relative to letters and background, aging is found to exert a great influence on the ease of reading, dark adaptation, and glare. As for the upper limb work range and reachability and the skillfulness in finger movement, it is found that aging narrows down the tolerant work area, lowers the working pace, and greatly affects skillfulness depending on the device operating method, all these disclosing actualities of difference attributable to age and sex. Concerning the device operating position and the ease of device operating force application, new measuring and evaluating methods are worked out, and correlations between the contents of operation and the operating position are seized. (NEDO)

Research report of FY 1997 on the environmentally acceptable coal utilization system introduction support project. Follow-up project on circulating fluidized bed boiler introduction (Calaca Batangas Thermal Power Station); 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system donyu shien jigyo (junkan ryudosho boiler ni kakawaru follow up jigyo (Calaca Batangas karyoku hatsudensho))

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For the follow-up project, to promote the diffusion of results of the clean coal technology (CCT) model projects, experts of circulating fluidized bed boilers were dispatched, to guide and advise for the operation of facilities introduced in these projects. The purpose of these projects is to diffuse the CCTs, and to support the promotion of environmental measures. Some guidance and advice about operation processes, data processing, operation regulation, maintenance, and boiler maintenance works were provided to the Ministry of Energy and Electric Power Corporation of the Philippines. Semirara, Malangas, and Samar coals in the Philippines were used for the tests. The boiler facilities could be operated by Philippine operators themselves. Based on the guidance and advice about operation processes, combustion tests using various Philippine coals were also planned and conducted by themselves. The maintenance techniques were transferred to Philippine operators through the inspection, repair and advice. The Philippine side understood the technologies well, and the circulating fluidized bed boiler technology was independently educated in the Philippines. 23 figs., 16 tabs.

FY 1999 report on the results of the joint study - project on the public facility use photovoltaic power generation field test; 1999 nendo kokyo shisetsunadoyo taiyoko hatsuden field test jigyo kyodo kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

In the field test, solar cell panels were installed on rooftop, and inverters were installed indoors. The electric power generated was connected at high pressure with electric installation of facilities and was also supplied to power equipment, lighting, air conditioning, etc. in facilities. The FY 1999 results were summarized. The installation of photovoltaic power generation facilities at 137 places and the results of the study were summarized in this report including a new university co-op building, Tokyo Metropolitan Advanced Technology Education Center, Suwano Center House of Fukushima prefecture, Environment Center of Saga prefecture, Educational Foundation Utsukushino Kindergarten, Hikarigaoka Park of Yamagata prefecture, Koiwai factory of Koiwai Dairy Products Co., Social Welfare Corporation Kameyama Ayumi Nursery School, etc. (NEDO)

Survey report on project for drawing district energy-saving visions for Town of Aizu Wakamatsu. Preliminary survey; 2000 nendo Aizu Wakamatsu shi chiiki sho energy vision sakutei nado jigyo (shoki dankai chosa) chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

The feasibility study is conducted for introduction of the district energy-saving measures in City of Aizu Wakamatsu, for which the actual situations of energy consumption and promising energy-saving measures are surveyed. The city has a typical basinal weather, cold in winter and very hot and humid in summer, and tends to have a longer air-condition period in a year. It is considered that there are many wasteful energy consumption items to be studied for reduction. In the area of moving means, dependence on public transportation systems is considered to be relatively low, suggesting that there are much space of reducing transportation energy by the measures such as self-imposed control on use of private cars, promotion of utilizing public transportation systems and fuel-saving type driving throughout the city. The promising energy-saving measures studied to verify the effects include introduction of PVM analyzers for establishing better cost/effect relationship between power consumed by air-conditioners and pleasantness; introduction of garbage power generation, co-generation and high-efficiency illuminators; improvement of power-factor; and demand control for air conditioning, rationalization of power-receiving facilities, introduction of systems for saving flushing water and improvement of air conditioners' outdoor facilities. (NEDO)

Survey report for fiscal 1999. Reference book for standard heat calculations in high-performance industrial furnace introduction field test project; 1999 nendo koseino kogyoro donyu field test jigyo chosa hokokusho. Hyojun netsu keisanshiki kijunsho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to verify in a short time the heat recovery capability being the evaluation parameter for the technologies to develop the high-performance industrial furnace, a standard calculation book will be prepared, which standardizes the data collection methods and heat calculation methods, and is used as the standard data sheets and bases. Evaluations and analyses will be given on business types, furnace constructions, thermal technologies, and functions in the research items adopted in the field test project. The results will be used to recognize the business entities engaged in the project in the next fiscal year, furnace types and sizes, establish the industrial furnace subjected to researches in the next fiscal year, and proliferate and expand the related business entities. Standard data sheets will be prepared on seven kinds of furnaces, heating furnaces (continuous and batch types), ladles, heat treatment furnaces (continuous and batch types), gas treatment furnaces, and melting furnaces. The standard data sheets will cover the following items: evaluation parameters (energy saving rate, thermal efficiency, and waste heat recovery rate), calculating conditions to be the base for the evaluation parameters, a heat production book to be the base for calculating the heat unit requirement, and a standard calculation book to be the base for the heat production table. The standard data sheets (including the standard calculation book) and floppy disks are submitted. (NEDO)

Model project for reduction of electric power consumption in cement plant. Report for fiscal 1999 on achievements of commissioned operation; Cement shosei plant denryoku shohi sakugen model jigyo 1999 nendo itaku gyomu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With objectives of utilizing energies efficiently and serving for environmental improvements, a model project was implemented for reduction of electric power consumption in cement plant in Vietnam. This paper reports the achievements in fiscal 1999. This project is intended to install waste heat boilers in waste gas lines in the preheating process in the cement plant, whose waste heat is recovered by steam to generate electric power by using steam turbines. The current fiscal year has executed the following activities: design of turbines, condensers, and oil units; discussions on the arrangement drawings thereof obtained from the Vietnam side; design of piping and provision of the detailed drawings thereof to the Vietnam side; planning of the electric cable routes; planning of instrumentation wiring routes; and grounding and interlocks. Results of the discussions on the proposed plant operation methods were reflected to the system design of the monitoring devices. Furthermore, the turbines were fabricated, and the associated facilities, valves, and piping materials were procured based on the detailed design. The piping materials were given pre-shipment inspections before having been transported to the site. (NEDO)

New energy vision for Ginoza village. Fiscal 2000 survey report on new energy vision formulation project for Ginoza village; Ginozason shin energy vision. 2000 nendo Ginozason shin energy vision sakutei nado jigyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-02-01

A new energy vision has been formulated for Ginoza village, Okinawa Prefecture, for the realization of symbiosis with nature. It is a 5,000-strong entirely farming village situated along the eastern coast at the middle of the main island of the Ryukyus, with energy consumption of 9,982 kl in terms of crude oil in fiscal 1999. The results of activities in this connection are summarized in six chapters, which are (1) the state of the village and new energy, (2) current state of energy supply/demand and outlook for the future, (3) existing amount of new energy, (4) trends of types of new energy under study, (5) feasibility of new energy introduction, and (6) Ginoza village's new energy vision. Chapter (6) is constituted of the general principles of new energy introduction into Ginoza village and a long-term vision of new energy introduction for each field, and discusses the introducible types which are photovoltaic power generation, wind power generation, small scale hybrid power source systems, fuel cells, natural gas fired cogeneration, refuse fueled power generation, and clean energy vehicles. (NEDO)

Fiscal 1997 international cooperation project. Report on the results of the research on environmental harmony type combustion technology; 1997 nendo kokusai kenkyu kyoryoku jigyo. Kankyo chowagata nensho gijutsu ni kansuru kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Out of the R and D on the environmental harmony type combustion technology, the results of the project carried out in fiscal 1997 were summed up. In the site survey, etc., visits were paid to France, Spain, Greek, Germany, the U.K. and the U.S. to have discussions and examine the trend of research on the NOx removal catalyst and catalyst combustion. In the actual R and D, the R and D were conducted on zeolite base NOx removal catalyst, oxide composite base NOx removal catalyst, alumina base NOx removal catalyst, direct decomposition type NOx removal catalyst, catalyst combustion, etc. In the R and D of the catalyst combustion, durability under high gas flow flux was examined of PdO-Pt/Ba-Al203 catalyst developed for low temperature use, which indicated that durability and low temperature activity were heightened. As high temperature use catalyst, high temperature durability was examined of the developed Pd0-La/Gd-ZrO2 catalyst, which showed that the durability was favorable. 322 refs., 261 figs., 55 tabs.

Fiscal 1998 research cooperation project on development of the easy-to-operate electronic design/production support system; 1998 nendo kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This report summarizes 'Research cooperation on the easy-to- operate electronic design/production support system' which was promoted together with Asian countries as a part of the international research projects. This project is promoted by joint research with research organizations in China, Indonesia, Malaysia, Singapore and Thailand. The project promotes the interexchange and cooperation of researchers along the memoranda on MATIC (Manufacturing Technology International Cooperation) concluded between NEDO and research organizations every country. The project is implemented by CICC (Center of the International Cooperation for Computerization) through the contract with NEDO. CICC is promoting this project with the production system future integrated information system committee, MATIC committee, and automobile, home appliance, fiber and apparel working groups. The project has been promoted by the survey in fiscal 1994, the basic planning in fiscal 1995-1996, and development of the prototype information system in fiscal 1996-1998. The final demonstration test is scheduled in fiscal 1998. (NEDO)

Fiscal 1998 overseas geological structure survey report on the engineer interchange project (coal mine technology field), Indonesia; 1998 nendo kaigai chishitsu kozo nado chosa gijutsusha koryu jigyo (tanko gijutsu bun'ya), Indonesia hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This project aims at improvement of coal mining technology and productivity in Indonesia by Japanese production control technology and business management technology for underground coal mining, through interchange of coal engineers between Japan and Indonesia. This project is composed of the short- term and long-term dispatch project of engineers to Indonesia, and the training project of Indonesian engineers in Japan. In fiscal 1998, the short-term dispatch was made for the training in Indonesia on underground coal mine development (development planning, pit mouth selection, main gallery design, mining system selection, transport planning, ventilation planning, under-river mining, mine water proofing, drainage). The long-term dispatch was made for contact and negotiation with concerned Indonesian organizations, support of the training project, and collection of information on the trend of Indonesian economy and energy, and the present and trend of the coal industry for conducting smooth and effective engineer interchange. (NEDO)

Fiscal 1999 technical survey report. Model project implementation feasibility study in China on effective utilization of cement waste heat; 1999 nendo Chugoku ni okeru cement hainetsu yuko riyo model jigyo jisshi kanosei chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Although China ranks first in the world in the manufacture of cement, yet the energy consumption rate is high and there remains room for improvement. Effective utilization of energy at cement making plants will not only profit the industry but also contribute to the stabilization of energy supply for China. The model project on power generation using cement waste heat implemented at Ningguo Cement Plant was concluded successfully. For the purpose of enabling China to domestically manufacture the equipment, the installation of such equipment at Zhujiang Cement Plant and Liuzhou Cement Plant in Guangxi Zhuangzu Zizhiqu was assumed, and their locations and plant operating conditions were studied. In addition, surveys were conducted of manufacturers of important components of the power generation equipment such as boilers, steam turbines, generators, and breaker boards. Two manufacturers were visited for each of the components, and they were checked for records of manufacturing similar equipment, quality assurance and process management capabilities, and for ability to satisfy required specifications. Among the visited manufacturers were Nanjing Turbine and Electric Machinery Co., Jinan Power Equipment Factory, and Hangzhou Boiler Works. Based on the results of the surveys, it was concluded that the model project may be implemented. (NEDO)

Overview of FY1997 human media technology R and D; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu seido Shin energy Sangyo Gijutsu sogo Kaihatsu Kiko itaku jigyo. Human media no kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper reports a summary of results in fiscal 1997 of research and development of human media technology. Fiscal 1997 launched design and trial fabrication of the following items: interface to improve efficiency and safety of plant operators, accommodation of multimedia contents to aid Kansei design, city development design aiding technologies using contents retrieval and presentation technologies and virtual reality, and empirical evaluation technologies for safety, comfort and convenience. Specific study assignments were extracted on a virtual media technology, a Kansei media technology and a knowledge media technology being three elementary technologies for human media to make clear the research and development approaches to be taken in the coming fiscal years. In addition, a human media technology committee, a research and development working group, and an investigation working group were established. Also launched were investigations on research trends in the human media technology, and investigative researches on contacts of information needs in industries with human media. 59 refs., 114 figs., 24 tabs.

Fiscal 2000 regional consortium research and development project - regional new technology creation research and development. Development of micro-array for next generation gene analysis (1st fiscal year); 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki shingijutsu soshutsu kenkyu kaihatsu seika hokokusho. Jisedai idenshi kaiseki micro array no kaihatsu (daiichi nendo)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are under way to construct a novel DNA (deoxyribonucleic acid) micro-array for gene diagnosis on the basis of technologies of laser scan type manipulation, nanometric position detection, and micro-machining. Using these technologies, structural changes to accompany reactions induced in the probe DNA deposited on an array are detected for the identification of the DNA. Activities are conducted in the four fields of (1) the study of probe DNA fixation technology, (2) development of an optical detection system, (3) detailed check of DNA micro-array performance evaluation technologies, and (4) a comprehensive survey. In field (1), gold colloid modified DNA molecules are designed and evaluated, and the fixation of DNA to substrates and technologies for integration are studied. In field (2), the gold colloid modified DNA is fixed on a thin gold film, and then a surface plasmon resonance (SPR) is observed in the wake of hybridization. Furthermore, a Brownian motion is observed of the metal particles fixed on a glass substrate via DNA. (NEDO)

Fiscal 2000 regional consortium research and development project - regional new technology creation research and development. Practicalization of polymer back light (1st fiscal year); 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki shingijutsu soshutsu kenkyu kaihatsu bun'ya seika hokokusho. Polymer back light no jitsuyoka ni kansuru kenkyu (daiichi nendo)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are being exerted to develop technologies for fabricating polyvinyl carbazole thin film, 100 nm or less in average thickness and 400 mm square in area, for the construction of an exothermal sheet utilizing polymer semiconductor light emission diodes. Activities are conducted in the three fields of (1) the development of large area light emission sheets for use in polymer LEDs (light emission diodes), (2) the study of manufacturing technologies, and (3) the study of technologies for testing, analyzing, and evaluating the material. In field (1), a polyvinyl carbazole thin film is fabricated by the use of a low viscosity resin liquid application method, and a film fabrication technique is established for fabricating a thin film on a 400 mm square substrate within {+-}3 nm of film thickness error. In field (2), studies are conducted of an integrated large area thin film application/transportation system, application device mechanisms, and control sequences for application devices. Through studies of technical literature, exhibitions, and research institute meetings in Japan and overseas, it is concluded that the polymer back light is commercially feasible. (NEDO)

Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium field / Development of 3D high speed bio-micromanipulation system (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium bun`ya / sanjigen kosoku bio-micromanipulation system no kaihatsu (daiichi nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This is aimed at developing a 3D high speed bio-micromanipulation system for small objects such as cells, bacteria and DNA. In fiscal 1997, a common platform for putting together and integrating individual technology owned by each member is trially fabricated, and the R and D of element technology to be integrated to it is divided up among members. As to selection/transportation technology, a basic experiment on screening by laser beams and electric field is conducted, and microfluid chips isolating bacteria are fabricated. Concerning positioning/fixation technology, cells and others which are comparatively larger than bacteria are freely positioned, and microdevices for fixation are trially fabricated. Relating to power measuring/controlling technology, developed is a multi-freedom degree contact type micromanipulator and a multi-axial minute sensor which enables the 3D mechanical manipulation of cells of the above-mentioned size, etc. The minute processing technology is developed to trially fabricate various microdevices which are integrated into the common flatform. 42 refs., 89 figs., 9 tabs.

FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D. Third year report. Ultra-high density information storage component; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu. Chokomitsudo joho storage component (dai 3 nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of industrially creating next generation HDD (hard disk drive), the development was proceeded with of ultra-high density and energy saving type next generation HDD system. The following four were conducted: 1) development of active type magnetic head arm for high speed writing/reading-out; 2) development of ultra-smooth low-noise medium using ultra-clean process; 3) establishment of component technology of high efficiency lubricating materials; 4) development of reproductive magnetic head using TMR device. TMR device is an ultra-high sensitivity magnetic detecting device composed of three layers of ferromagnetic material/insulator/ferromagnetic material. As to the development of regenerative magnetic head, studies were made of the reduction in resistance of TRM device, fabrication of submicron device and system integration. For the development of low resistance TMR device, thickness of Al layer, oxidation conditions and heat treatment conditions were studied in detail. The tunnel joining was obtained in which RA value and TMR ratio are 80 ohm(center dot){mu}m{sup 2} and 30%, respectively, in case of the thickness of Al layer of 6.6 (angstrom). (NEDO)

Report on projects of the basic survey of effective energy consumption in developing countries and the invitation of engineers of developing countries to Japan (Vietnam, the Philippine, Indonesia and Thailand) in FY 1997; 1997 nendo chosa hokokusho Hatten tojokoku energy shohi koritsuka kiso chosa to jigyo hatten tojokoku gijutsusha shohei jigyo (Vietnam, Philippines, Indonesia Tai)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Based on the significance of technological training for energy saving and environmental protection, NEDO has invited administrators and engineers of four countries in Southeast Asia. Pollution prevention technology, administrative methods and energy saving measures in Japan were lectured in the International Center for Environmental Technology Transfer. The training curriculum included (1) basic law of environment and local administration from the viewpoint of criminal law concerning history of air pollution problems and countermeasures in Yokkaichi petroleum industrial complex, (2) prospect of new energy technology development in Japan relating to the energy saving law, (3) energy saving measures, air/exhaust gas/dust treatment for environmental protection, and actual waste treatment measures by typical individual industries, and (4) significance of common management technology for individual treatment measures. Policies of energy saving and environmental protection and technology information in Japan which can be transferred were provided to two administrators of energy saving in the industry sector of Management of Science, Technology and Environment of Vietnam. 12 figs.

Report on investigations in fiscal 2000 on the projects to support introduction of environment friendly coal utilization system. Green helmet project for briquette production plant - Mae Moh coal mine, Thailand; 2000 nendo kankyo chowagata sekitan riyo system donyu shien jigyo chosa hokokusho. Briquette seizo setsubi ni kakawaru green helmet jigyo (Thai koku Mae Moh tanko)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-06-01

This Green Helmet Project is intended to suppress generation of environment polluting substances in association with coal utilization in Thailand by demonstrating and improving the proliferation infrastructure for the clean coal technology to be used widely in Thailand. The project is also intended to serve for stabilized assurance of energies for Japan. The demonstration project related to briquette manufacturing facilities executed as one of the 'Projects to support introduction of environment friendly coal utilization system' is intended to manufacture at low cost a briquette which is low in odor, free of smoke, and suppressed largely of sulfur oxide generation. The briquette is made by adding clayish minerals, sulfur, a fixing agent and a binder into brown coal being a low grade coal. The project implements proliferation of the technology to reduce environmental load associated with coal utilization in developing countries according to the situation and needs of the counterpart countries. The present project has performed the site surveys and guidance of operation and maintenance techniques as follow-up works of the demonstration project having been completed by cooperation between Japan and Thailand. It is considered that what had been intended in the beginning has been achieved sufficiently. (NEDO)

Report on the survey of the project on the environmentally friendly type energy community field test. Investigative project for development and commercialization of recycle technology of waste edible oil; 2001 nendo kankyo chowa gata energy community field test jigyo chosa hokokusho. Hai shokuryo yu no recycle gijutsu kaihatsu to jitsuyoka no tameno chosa jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-06-01

An investigative study was made of the use of waste edible oil as fuel and recycle use of residual food in the food service business. As to the existence/recovery of edible oil, it was found out that waste edible oil of 15.9g/meal per capita was discharged at multiple wide-area distributed shops and that the total amount reached 1,861kl/y in the country. Concerning the technology for using it as biodiesel fuel, Ronford Co., which has the most actual results of the technology, recovers waste edible oil in Kyoto City, refines it and uses it as fuel for the City's garbage truck. About the use of waste edible oil as boiler use fuel, there are examples in Sapporo Grand Hotel, which has been contributing to energy conservation for more than five years. In the assessment of the profitability as project, for the direct combustion for boiler fuel use, the same/large heat supply system is a prerequisite, and for the hot stove loaded type direct combustion, there is an element of the technology development. Therefore, the use as bio-diesel fuel is most expected, though there is a taxation problem. (NEDO)

Report on the survey of the project on the environmentally friendly type energy community field test. Investigative project for development and commercialization of recycle technology of waste edible oil; 2001 nendo kankyo chowa gata energy community field test jigyo chosa hokokusho. Hai shokuryo yu no recycle gijutsu kaihatsu to jitsuyoka no tameno chosa jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-06-01

An investigative study was made of the use of waste edible oil as fuel and recycle use of residual food in the food service business. As to the existence/recovery of edible oil, it was found out that waste edible oil of 15.9g/meal per capita was discharged at multiple wide-area distributed shops and that the total amount reached 1,861kl/y in the country. Concerning the technology for using it as biodiesel fuel, Ronford Co., which has the most actual results of the technology, recovers waste edible oil in Kyoto City, refines it and uses it as fuel for the City's garbage truck. About the use of waste edible oil as boiler use fuel, there are examples in Sapporo Grand Hotel, which has been contributing to energy conservation for more than five years. In the assessment of the profitability as project, for the direct combustion for boiler fuel use, the same/large heat supply system is a prerequisite, and for the hot stove loaded type direct combustion, there is an element of the technology development. Therefore, the use as bio-diesel fuel is most expected, though there is a taxation problem. (NEDO)

Survey report for fiscal 1998. International project for rationalizing energy use (a project for investigating analyzing a tool to improve energy consumption efficiency in Asia) (Data collection 1 (Year 1990 data)); 1998 nendo kokusai energy shiyo gorika nado taisaku jigyo chosa hokokusho. Asia energy shohi koritsuka bunseki tool chosa jigyo (shiryoshu 1 1990 nen data)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

With an objective to identify quantitatively the mutually influencing effect of economical development and energy consumption efficiency improvement in the entire Asia-Pacific region, a data collection was prepared according to the common industry classification as a tool to analyze energy consumption improvement in Asia. This data collection summarizes the industry relation tables and the energy relation tables available in eight Asian countries (Korea, Indonesia, Thailand, Philippines, China, Taiwan, Singapore and Malaysia) and Japan. Both kinds of the tables are unified in conception among the nations, hence comparable. The industry relation table consists of a basic transaction table, a charged coefficient table, a final demand converter table, an import coefficient table, a reverse matrix table, a sensitivity coefficient able, an influence force coefficient table, a production inducing amount table, a production inducing coefficient table, a production induction dependence table, an import inducing amount table, an import induction coefficient table, and an import induction dependence table. The energy table consists of an energy input table, an energy consumption table, and an emission table. (NEDO)

Report for fiscal 1999 on the international and fundamental cooperation project for energy consumption efficiency improvement and the international conference project such as IPCC. The meetings of IPCC specialists and IPCC symposiums; 1999 nendo kokusai energy shohi koritsuka nado kyoryoku kiso jigyo / IPCC nado kokusai kaigi jigyo. IPCC senmonka kaigo oyobi IPCC symposium hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-10-01

This paper reports the meetings of specialists and the symposiums by the inter-governmental panels for climate change (IPCC) in fiscal 1999. Three working groups were established for evaluation on climate change from scientific aspects, evaluation on effects and countermeasures from socio-economic aspects, and evaluation on mitigation measures from socio-economic aspects. The working groups have started preparing the third evaluation reports. Common problems are handled in a unified framework as the traversable problems. Specialist meetings are held for several important themes. Especially for the cost problems, preparation of a guidance paper has started, that include the costs and benefits by territories and departments. The themes for the specialist meetings include: cost problems related to effects and countermeasures for climate change and mitigation measures; the IPCC activities for the cost evaluation in the past and an outline of the traversable problems; problems in effects, applicable measures, and mitigation measures; and unification of the cost evaluations. The themes for the symposiums are the frontier line of the climate change problems, and include the outline of IPCC, the current status and issues in the working groups and the special reports for each group. (NEDO)

Fiscal 1998 intellectual infrastructure project utilizing civil sector functions. Research and development project on prompt-effect type intellectual infrastructure creation (Research and development concerning environment-related reference materials); 1998 nendo minkan no kino wo katsuyoshita chiteki kiban jigyo seika hokokusho. Sokkogata chiteki kiban sosei kenkyu kaihatsu jigyo (kankyo kanren hyojun busshitsu ni kansuru kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Concerning an information providing system on environment-related reference materials, studies were conducted about the contents of information to be provided and about hardware and software suitable for such a system. In a survey of needs for such an information system, questionnaires were sent to 320 agencies and business corporations providing or utilizing reference materials in the field of chemistry and environments, and 158 answers were received. Further surveys were carried out by visiting more than 20 organizations providing or utilizing reference materials. As for activities overseas, surveys were conducted in Europe, North America, and Oceania, when IRMM (Institute for Reference Materials and Measurements) of Belgium, Merck KGaA of Germany, and some others were visited. It was then found that they desired that retrieval of information on reference materials in Japan and abroad be enabled by merely accessing related Internet sites. To meet the wish, a concept design was prepared of a comprehensive information system on reference materials in the form of an Internet home site. (NEDO)

Fiscal 1999 research report. Data acquisition and analysis on the advanced high-efficiency energy system field test; 1999 nendo sendoteki kokoritsu energy system field test jigyo ni okeru data shuyaku oyobi hyoka kaiseki chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Although the next-generation phosphoric acid fuel cell has nearly reached its practical application stage as far as technology is concerned, its diffusion is yet to come due to lack of data about its cost efficiency and reliability. Under the circumstances, the goal now is to collect and analyze various data obtained in the above-named project which was started in fiscal 1997 for the compilation of data useful for full-scale diffusion in the future so that a foundation may be built for the overall popularization of the fuel cell. In this fiscal year, assessment and analysis have been conducted at 15 test sites now in presence. At the second plant of the Semboku LNG Terminals where approximately 17,000 hours have elapsed since the test began, the cell has operated for more than 16,000 hours in total. The Mycal Bore Sanda has established the longest uninterrupted operation record of 6,500. As for power generation efficiency, a town gas 13A-fueled system exhibits approximately 40% operating smoothly at a high overall efficiency of not less than 90%. (NEDO)

Joint research achievement report on field test project for photovoltaic power generation of industrial use in fiscal 2000 (5/5); 2000 nendo sangyo tou you taiyokohatsuden field test jigyo kyodo kenkyu seika hokokusho 5/5

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-05-01

This paper summarizes the achievements in fiscal 2000 on the field tests for photovoltaic power generation of industrial use. This report describes the details of the achievements on the following organizations: the Hiroshima Riverside Hotel; the Saraya Corporation; the Nanshin Subaru Corporation; the Ricoh Uni-techno Corporation; Toyota Motors Kyushu Corporation (Eco-center); Hitachi Electric Wires; Yuasa Corporation, Furukawa City in Ibaraki Prefecture; the Takasaki Branch Office of East Japan Passenger Railways; the World Trade Center Building, the Minami Trading Company, Onga Township in Fukuoka Prefecture; the Keio Electric Railways (Wakabadai Station); the Business Enterprise Bureau of Kyoto Prefectural Government; Okinawa Electric Power (Kita-Daito Island), Kawagoe Township in Mie Prefecture, the Keio Electric Railways (Meidai-mae Station); Kitakata Township in Gifu Prefecture; the Yamaguchi Prefectural Government; the MSK Corporation; the Fuji Pream Corporation; Kumano Township in Hiroshima Prefecture; Fukuroi City in Shizuoka Prefecture; the Water Supply Bureau of Yokohama Municipality in Kanagawa Prefecture; Ashiya City in Hyogo Prefecture; Shinoyama City in Hyogo Prefecture; the Gantan Beauty Industry; the Toyokuni Industry; and Minoo City in Osaka Prefecture. (NEDO)

FY 1999 project on the development of new industry support type international standards. Standardization of color management; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Iro saigen kanri (color management) no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of eliminating variations in color reproduction in multi-media output devices, study was conducted of making a standard plan for color information equipment as hardware and for the software to determine the characteristics, and the FY 1999 results were summarized. As to the standardization of color control in input/output devices, characteristic dependency of color printer under environmental conditions such as ambient temperature/humidity was determined. And to integrate it into the ICC profile, the profile was expanded. Concerning the standardization of multi-spectrum color image description format, non-linear spectral characteristics were investigated which are dependent on types of light sources, light intensity and geometric conditions. In relation to the standardization of psychological color reproduction, the scope of the experiment using examinee was expanded, and the study was so conducted that the standard image for skin color evaluation use can be recognized as the one that has statistical accuracy. A sequence method which is more simple and more effective was established. In the discussions of the proposed international standards, studies were carried out of the electronic still camera color characteristics measurement and the color space ISO RGB. (NEDO)

Achievement report for fiscal 1998 on joint research business (2/2). Photovoltaic power generation field test for public facilities; 1998 nendo kokyo shisetsu nadoyo taiyoko hatsuden field test jigyo (2/2). Kyodo kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

Photovoltaic power generation systems are experimentally installed at public facilities at various locations, and subjected to field tests in which they experience long-term operation under real loads. Mie Prefectural Iidaka Senior/Junior High School has a 10kW solar cell system installed on the south-side roof of the school house. The system is linked to an in-house transformation station and the power generated by the system is supplied to the lighting and air-conditioning facilities in the building, and surplus if any is transmitted to the Chubu Electric Power Co., Inc., system. A field test is being conducted to determine if there are usability and safety in the 10kW system. A number of like systems are undergoing field tests, installed at a comprehensive technological training center of Kyushu Electric Power Safety Association, Kongo Gakuen Senior High School, Sakata Nursery School, Taiyo Daiichi Nursery School, Minami Kindergarten, Neyagawa Ishizu Old People's Home, Co-Op Living Konan, Factory Hishimeki, Tochigi Fuji Industries, Gamo-cho Hirabayashi Public Hall, Fukuoka Prefectural Culture Complex, Yatsusugi Forest Schooling Center, Osaka Prefectural Murano Water Purification Plant, Yamanashi Institute of Environmental Sciences, Utatsu-cho Town Office, Ginga Gakuen Junior High School, etc. (NEDO)

Report on the survey of the project for working out the new energy vision of Shinjo Village. New energy vision of Shinjo Village; 2001 nendo Shinjo son shin energy vision sakutei tou jigyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-02-01

For the purpose of promoting the introduction of new energy and enhancing the awareness of it in Shinjo Village, Okayama Prefecture, an investigational study was conducted of the energy demand of the village, existence amount of new energy, project for new energy introduction, etc., and a new energy vision was worked out. The energy demand amount of the village was estimated at 1,442.5kL in terms of crude oil. The rate of energy source was 48% of automobile use fuel, 25% of electric power, 20% of kerosene and 7% of LPG. As the project for new energy introduction, the following were studied: power generation by direct combustion/gasification of wood biomass such as forest trees; power generation/heat utilization using agricultural waste such as rice straw/hull; production/utilization of wood pellet; introduction of photovoltaic power system/solar heat utilization system to tourist facilities/welfare facilities such as the village office/elementary school/junior high school/michi-no-eki (service area along the road); introduction of clean energy vehicle to tourist resort; introduction of street light with solar panel/wind power generator/storage cell; introduction of micro hydraulic power generation. (NEDO)

Fiscal 1996 New Sunshine Plan auxiliary project. Report on results on development of coal hydrogasification technology (Support research); 1996 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Sekitan suiso tenka gaska gijutsu kaihatsu shien kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

R and D was conducted for the purpose of developing the alternative natural gas manufacturing process that, using coal as the raw material, is highly efficient as well as environmentally superior, with the fiscal 1996 results reported. A test research was carried out on the coal hydrogasification process which was selected as the optimum process based on the studies in the previous years. On the basis of the results of the studies, a free fall pyrolyzer was employed as the test equipment for the use of behavior research of hetero-elements in the test. The basic specifications were set based on a hydrogen/coal ratio of 0.2, a temperature of 950 degrees C and a pressure of 7 MPa, which are the reaction conditions of the ARCH reactor, with the basic design drafted accordingly. In a preliminary examination on the mechanisms of the coal hydrogasification reaction, analysis was made on the representative 20 different kinds of coals, on the six kinds of which studies were made on the gasification behavior using a constant heating rate pyrolyzer. As a result, from the temperature dependency of a methane forming speed, it was assumed that three components of coal had bearing upon the gasification behavior. (NEDO)

Fiscal 1998 New Sunshine Plan auxiliary project. Report on results on development of coal hydrogasification technology (Support research); 1998 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Sekitan suiso tenka gaska gijutsu kaihatsu shien kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

R and D was conducted for the purpose of developing the alternative natural gas manufacturing process that, using coal as the raw material, is highly efficient as well as environmentally superior, with the fiscal 1998 results reported. A hydrogasification test was conducted on Taiheiyo coal at a temperature of 1,173k and a pressure of 7 MPa, which showed that all gaseous products other than methane stopped their evolution roughly in the heat-up process, while methane continued to evolve to show the highest yield. In the reactivity comparison of various types of coal, coals with carbon content of 80% or below were high in reactivity and considered suitable for hydrogasification feedstock. It was also suggested that the hydrogasification reactivity of low rank coals including sub-bituminous coals or below might be greatly affected by the presence/absence of the catalytic effects of ion-exchanged metals. Behavior experiments of sulfur and nitrogen in coal in the hydrogenation reaction were carried out using a continuous free-fall type reactor, which elucidated the effects of hydrogen pressure and gas residence time among various operational elements. (NEDO)

Achievement report for fiscal 1998 on joint research business (2/2). Photovoltaic power generation field test for industrial purposes; 1998 nendo sangyo nadoyo taiyoko hatsuden field test jigyo (2/2). Kyodo kenkyu gyomu seika hokokushyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

Solar cell systems are installed on the roofs of facilities at various locations, and verification tests are conducted for usability and safety they will exhibit after prolonged operation under real loads, and this project aims at the popularization of photovoltaic systems. At Children's Ferrite and Science Museum of Nikaho Town, Akita Prefecture, a 20kW solar cell system is installed on the rooftop, and a 20kW inverter in the machine house. The power obtained is connected in a high-voltage interconnection to electric facilities in the museum, and supplied to in-house power facilities, illuminating systems, and air-conditioning equipment. Operation-related data are recorded in a data recording unit. Similar facilities are installed at corporations and institutions such as WAIDA Works, Kuriyama Shop, Nikko Building, Kiya Works, Aichi Prefectural Tobishima Junior High School, Gunma Prefectural Niisato Hall of Commerce and Industry, Ube Techno-Enji Corporation, Tezukayama Gakuin University, Kinki Kensetsu K.K., Takaoka Electric Manufacturing Company, Aichi Prefectural Incorporated Educational Institution Miura Gakuen, Asaguchi Taxi Company, Family Mart, etc., and field tests are under way for them. (NEDO)

Achievement report for fiscal 1998 on joint research business (1/2). Photovoltaic power generation field test for public facilities; 1998 nendo kokyo shisetsu nadoyo taiyoko hatsuden field test jigyo (1/2). Kyodo kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

Photovoltaic power generation systems are experimentally installed at public facilities at various locations, and subjected to field tests in which they experience long-term operation under real loads. At Livelihood Cooperative Association Co-Op Kanagawa, a photovoltaic cell system is installed on the roof, facing true south, of its Yokohama eastern district joint purchase center, and the power generated by the system is utilized as interconnected with the commercial distribution line connecting to its power facilities. It is called a '10kW Photovoltaic Power Generation Model System,' and is subjected to a verification test, carried over from the previous fiscal year, centering about its usability and safety. Similar systems are also installed at many locations, such as the Kadosawa Bridge district of Ebina City, Kanagawa Prefectural Industrial Technology Research Center, Shiga Prefectural University, Suntory Museum, Fukui Institute of Technology, Saigo Police Station, Higashi-Murayama Water Purification Plant, Kanagawa Prefectural Disaster Prevention Center, Toyosato-cho Health Center, Kyodo Gakusha School, Sakuragi Nursery School, Yagi Junior High School, Shizuoka Prefectural Environmental Radiation Monitoring Center, Tanabe City Health Center. (NEDO)

Survey report for fiscal 1998. Joint research project with researchers related to petroleum substituting energies in the EU countries; 1998 nendo EU shokoku no sekiyu daitai energy kanren kenkyusha tono kyodo kenkyu jigyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

It was intended to invite researchers related to petroleum substituting energies from the EU countries to perform joint researches at research organizations under the auspices of the Agency of Industrial Science and Technology having deep relations with research themes of the invited researchers, to deepen the mutual understanding, and to form efficient cooperative relationship. The intention is also to contribute to research and development of petroleum substituting energies to be used in Japan in the future. The research themes, researchers, their research organizations, and the receiving research organizations are as follows: (1) evaluation of reservoir impedance in high-temperature rock experimental fields by Mr. Ralph Weidler (Germany) at Ruhr University received by the Resource and Environmental Technology Research Institute; (2) changing the particle boundary structure of ceramics by using the alkoxide process by Dr. Ramon Torrecillas (Spain) at Institute Nacional del Carbon received by the Nagoya Industrial Technology Research Institute; (3) research on corrosion in metallic materials for molten carbonate type fuel cells by Dr. Giuseppe Calogero (Italy) at Institute for Transformation and Storage of Energy received by the Osaka Industrial Technology Research Institute; and (4) estimation of behavior of deep geothermal reservoirs with high enthalpy by Dr. Enrico Maranini at Universita' Di Ferrara received by the Geology Survey Center. (NEDO)

Fiscal 2000 research cooperation project on the research cooperation on practical application of wastewater treatment technologies for global warming prevention; 2000 nendo chikyu ondanka boshi haisui shori gijutsu no jitsuyoka ni kansuru kenkyu kyoryoku jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A verification plant operation study is conducted in cooperation with Thailand over wastewater treatment technologies for effectively decomposing and removing organic matters contained in foods plant wastewater and for recovering methane gas therefrom. The effort aims to transfer to Thailand anaerobic wastewater treatment technologies for recovering methane gas. For the 3-year research that began in fiscal 1998, a verification plant was installed at Cho Heng Rice Vermicell Factory Co., Ltd., located 30 kilometers west of Bangkok City. In the first half of verification plant related operation studies for fiscal 2000, the plant was kept in operation for the determination of the optimum operating conditions, and operation/maintenance technologies were transferred to Thailand. In the second half, plant operation was studied for by-passing the ultimate sedimentation tank of the factory. The results of activities are summarized into seven chapters of (1) outline of research cooperation project implementation, (2) outline of project implementation in fiscal 2000, (3) verification plant operation study, (4) automatic monitoring system construction, (5) technology disseminating activities, (6) study of support in Japan, and (7) subjects for future discussion. (NEDO)

FY 1999 Report on the technical results. Research and development project for creation of the quick-effect type international standards (Comprehensive surveys); 1999 nendo sokkogata kokusai hyojun sosei kenkyu kaihatsu jigyo seika hokokusho. Sogo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Safety, environment protection and internationality are most important product qualities, and international standardization of product qualities and testing methods are essential for strengthening international competitiveness. Viewed from this angle, the R and D project is conducted to propose the international standards for the following 5 areas related to environment and safety, selected in expectation that the results could be obtained in short time for preparation of the international proposals; (1) standardization of the wireless IC tags for logistics management, (2) standardization of quality and testing methods of automobile fuels and lubricants, (3) research and development for international standards in the field of safety of machinery, (4) standardization of evaluation methods for electronic data security system, and (5) standardization for the safety of light emitting diodes. The results are obtained for preparation of the international standard drafts, interim or final. The activities are directed to promotion of international interchangeability of radio frequency identification (RFID) systems for area (1); to standardization of the systems for emergency stopping/controlling machines for the area (3), to improvement of security evaluation standards of existing information systems for the area (4), and to unification of the ISO/IEC safety standards for the area (5). (NEDO)

Fiscal 1999 technical survey report. Model project implementation feasibility study in India on cement calcination facilities waste heat recovery; 1999 nendo Indo ni okeru cement shosei setsubi hainetsu kaishu model jigyo jisshi kanosei chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

India produces 96-million tons/year of cement, ranking fourth in the world, and 55% of the yield comes from 1-million tons/year plants. Some of the waste heat from the manufacturing process is used to dry materials, etc., but much is discharged into the atmosphere. Estimation is made of the energy conservation effect expected to be brought about in case the waste heat power generation technology which is in use to good effect in Japan is introduced into Indian cement plants whose clinker production exceeds 3,000 tons/day. As the result, it is concluded that the model project may be implemented at any of the four plants for which power generation capability and CO2 reduction effect are tentatively calculated below. There will be power generation of 7,300kW and CO2 reduction of 43,125 tons for the Guijarat Ambuja Cement Ltd./Ambuja Cement Eastern plant; power generation of 7,700kW and CO2 reduction of 901,960 tons for the India Cement Ltd./Rassi Cement plant; power generation of 45,098kW and CO2 reduction of 1,140,220 tons for the Larsen and Toubro Ltd./Hirmi plant; and power generation of 5,450kW and CO2 reduction of 32,230 tons for the J. K. Corp Ltd./Lakshmi Cement Sirohi plant. (NEDO)

Fiscal 1998 research cooperation project on development of the easy-to-operate electronic design/production support system; 1998 nendo kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This report summarizes 'Research cooperation on the easy-to- operate electronic design/production support system' which was promoted together with Asian countries as a part of the international research projects. This project is promoted by joint research with research organizations in China, Indonesia, Malaysia, Singapore and Thailand. The project promotes the interexchange and cooperation of researchers along the memoranda on MATIC (Manufacturing Technology International Cooperation) concluded between NEDO and research organizations every country. The project is implemented by CICC (Center of the International Cooperation for Computerization) through the contract with NEDO. CICC is promoting this project with the production system future integrated information system committee, MATIC committee, and automobile, home appliance, fiber and apparel working groups. The project has been promoted by the survey in fiscal 1994, the basic planning in fiscal 1995-1996, and development of the prototype information system in fiscal 1996-1998. The final demonstration test is scheduled in fiscal 1998. (NEDO)

Achievement report for fiscal 1998 on joint research business (2/2). Photovoltaic power generation field test for public facilities; 1998 nendo kokyo shisetsu nadoyo taiyoko hatsuden field test jigyo (2/2). Kyodo kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

Photovoltaic power generation systems are experimentally installed at public facilities at various locations, and subjected to field tests in which they experience long-term operation under real loads. Mie Prefectural Iidaka Senior/Junior High School has a 10kW solar cell system installed on the south-side roof of the school house. The system is linked to an in-house transformation station and the power generated by the system is supplied to the lighting and air-conditioning facilities in the building, and surplus if any is transmitted to the Chubu Electric Power Co., Inc., system. A field test is being conducted to determine if there are usability and safety in the 10kW system. A number of like systems are undergoing field tests, installed at a comprehensive technological training center of Kyushu Electric Power Safety Association, Kongo Gakuen Senior High School, Sakata Nursery School, Taiyo Daiichi Nursery School, Minami Kindergarten, Neyagawa Ishizu Old People's Home, Co-Op Living Konan, Factory Hishimeki, Tochigi Fuji Industries, Gamo-cho Hirabayashi Public Hall, Fukuoka Prefectural Culture Complex, Yatsusugi Forest Schooling Center, Osaka Prefectural Murano Water Purification Plant, Yamanashi Institute of Environmental Sciences, Utatsu-cho Town Office, Ginga Gakuen Junior High School, etc. (NEDO)

Survey report on the environment harmonizing type energy community survey project for the coastal area in the Kawasaki ward in fiscal 1998; 1998 nendo Kawasakiku rinkaibu chiiki kankyo chowagata energy community chosa jigyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In energy utilization in the 'Kawasaki Zero Emission Industrial Complex', optimal regional heat supply systems were discussed. The discussion was made from the viewpoints of introduction of saving-type energies, new energies and renewable energies, and environment preservation performance. The coastal area in the Kawasaki ward is planned of developing an industrial complex with an area of 8.4 ha for operation of about twenty companies. In the assumption of heat demand, four companies only were taken up as the object of the discussion, who utilize heat supply from steam as process heat source for their factories. The total heat demand quantity and heat demand pattern used for the discussion were assumed by hearing and actual record submitted from each company. Optimal systems were discussed on heat supply systems utilizing steam produced by steel mills, with the discussion made on waste heat recovered steam in processes and steam extracted from thermal electric power plants in the steel mills. As a result of the discussion, heat supply utilizing the steel mill steam was found capable of being provided with much lower price level as the estimated unit price than general direct steam supply, leading to a judgement that the system has business feasibility. (NEDO)

FY 1999 report on the model project on the effective utilization of waste-base biomass fuels. Basic survey for the feasibility; 1999 nendo haikibutsukei biomass nenryo yuko riyo model jigyo jisshi kanosei kiso chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Survey on the waste biomass was conducted for Thailand, Malaysia, Indonesia, Vietnam, Laos, Nepal, Butan, Myanmar and Cambodia to study feasibility of the project for the concrete utilization of biomass resources. In Thailand, it is expected to construct large-scale model plants for biomass resources such as rice hulls, bagasse, wood waste and oil palm. In Malaysia, expected are the cogeneration at 5MW class palm oil plant, large-scale power plant using wood waste, plant using the biomass from waste palm oil, etc. In Indonesia, there is a great potentiality, but it is necessary to handle it carefully in consideration of the unstable situation of the society. In Vietnam, the detailed survey of feasibility is needed on the project for efficiency heightening at state-run plants, the assumed national plants (recommended by the government), etc. In Laos, small-scale power generation using the forestry waste such as sawdust is expected. (NEDO)

FY 2000 report on the results of the regional consortium R and D project - Regional consortium R and D. Third year report. R and D of the transversal maintenance technology; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium kenkyu kaihatsu. Odanteki maintenance gijutsu no kenkyu kaihatsu (dai 3 nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of eliminating bad effects of the maintenance/management of equipment/facilities of plants which are made separately and of heightening efficiency of work and improving technology, persons in charge of maintenance/management, persons requesting maintenance/management and official research institutes proceeded as one with the construction of a system doing maintenance/management work. Concretely, three parties cooperated in integration and enhancement of element technologies such as inspection/diagnosis and arrangement/repair and developed the maintenance/management system (maintenance center) which does not specify objects. Based on this system, development was made of the network connecting between the center and facilities, diagnosis car, and multi-functional repair car. Studies were made on the following three. As to the system development, conducted were the development of a deterioration mode prediction system, basic structuring of a remote maintenance network, and making of fatigue/corrosion/abrasion database. Concerning the tool development, technology to foresee damages on the static portion such as piping, etc. were developed. In the study of field application, conducted were analysis of maintenance flow, development of retrieval system of equipment parts/personnel/operation procedures and multi-functional repair car, etc. (NEDO)

Report on survey for high-performance industrial furnace introduction field test project in fiscal 1999. Verification work on achievements of industrial furnace development in 1999 by using theoretical method; 1999 nendo koseino kogyoro donyu field test jigyo chosa hokokusho. 1999 nendo koseino kogyoro kaihatsu seika no rironteki shuho ni yoru kakusho gyomu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The high-performance industrial furnace introduction field test project has been executed from fiscal 1998 through fiscal 2000. Fiscal 1999 has performed measurements, evaluations, analyses, and follow-ups on representative demonstration furnaces, subsequently from fiscal 1998. At the same time, theoretical discussions were given to understand the details of the achievements. The measurements and investigations on the representative demonstration furnaces verified remarkable enhancement in the waste heat recovery rate, and noticeable reduction in the fuel unit requirement. In order to understand in-furnace phenomena and heat conduction mechanisms, simulations were made on combustion gas flows, combustion reactions, and heat conduction by using three-dimensional and non-steady state continuous analyses. The method used is an effective method to elucidate the in-furnace gas temperature distribution in terms of space and time, and evaluate the heat conducting performance quantitatively. The result obtained in the current fiscal year on the overall heat absorption rate was found to be about the same value as for conventional furnaces. The temperature efficiency calculation value for the heat recovering device was 90 to 95%, which is much higher than that for the conventional furnaces of 30 to 60%. The calculation value for the fuel unit requirement was also reduced by 20 to 30% from that of the conventional furnaces. The simulation result is effective in understanding the heat conduction performance enhancing mechanism, having been supplemented by the measurements. (NEDO)

Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium field / R and D on process adaptive type flexible robot technology (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium bun`ya / kotei tekiogata flexible robot gijutsu ni kansuru kaihatsu (daiichi nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For the purpose of establishing robot technology required for the construction of a highly functional automation line with flexibility, the R and D were conducted. At Kumamoto University, a model following type power control system was studied into which polynominal trajectory formation algorithm was integrated. Also studied was damping control of robot arms in a disturbance environment. The following were further carried out: experimental verification (HIRATA Corporation) of the application of power control and intelligent control to transportation equipment production line, experimental verification (SAKURAI SEIGI Co. Ltd.) of the application of power control and intelligent control to semiconductor testing equipment, R and D (OMRON Corporation) of high accuracy force sensing and positioning system, research (Kumamoto Technopolis Foundation) on flexible arms/hands suitable for cooperative control, sensor-based skill (Electrotechnical Laboratory), research (Kyushu National Industrial Research Institute) on tactual system and tactual sensing, etc. 20 refs., 86 figs., 14 tabs.

Fiscal 1998 intellectual infrastructure project utilizing civil sector functions. Research and development project on prompt-effect type intellectual infrastructure creation (Data buildup for assurance of safety of non-ferrous metals); 1998 nendo minkan no kino wo katsuyoshita chiteki kiban jigyo seika hokokusho. Sokkogata chiteki kiban sosei kenkyu kaihatsu jigyo (hitetsu kinzoku no anzensei kakuho ni shisuru data seibi)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Data were collected, put in an easy-to-use order, and developed into a database for safety assurance for automobiles and transportation equipment built of light metals as represented by aluminum. In the collection and arrangement of existing dynamics data, a database having 52 data relating to dynamic properties was prepared after retrieving data from academic essays previously published in Japan and abroad. In the testing of new materials, a Hopkinson high-speed rod-type impact/tensile tester was used to perform tensile tests at eight load application speeds between 0.5mm/min and 50m/sec for practical aluminum alloys 2024, 2091, 5052, 5083, 5254, 6061, 6063, 6NO1, 7075, and AC4CH. As the results, data on the 5000 and 6000 series alloys which had been insufficient were complemented. Data from a newly introduced multi-functional instrumentation Charpy impact tester were compared for study, correlations between property values obtained from bend test specimens and those obtained from tensile test specimens were evaluated, and then a simplified test evaluation method was proposed. (NEDO)

Fiscal 2000 achievement report on project for research and development of intelligent infrastructure creation and utilization technologies. Research and development project on high-speed deformation characteristics evaluation methods for metallic materials; 2000 nendo chiteki kiban sose riyo gijutsu kenkyu kaihatsu jigyo. Kinzoku zairyo no kosoku henkei tokusei hyoka hoho no kenkyu kaihatsu jigyo - Gyomu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts were made to develop methods for evaluating the characteristics of metallic materials experiencing high-speed deformation or impact deformation. The research was conducted by the research WG (working group) consisting of some participants of an international conference convened this fiscal year. The research result revealed that studies in Japan lopsidedly dealt with metallic materials at strain velocity of 10{sup 4}/second or less, such as steel, while many studies overseas dealt with materials other than metals at strain velocity over 10{sup 4}/second. The test and evaluation WG conducted high-speed tension tests for T6-treated aluminum alloys using the split Hopkinson bar method, hydraulic servo method, one bar method, and the sensing-plate method for measuring force, and the results were compared. It was then found that the one bar method produced disturbance more remarkably than the others and that the loading block structure and load rise time influenced the emergence of the peak load. The emergence of a peak load in the Hopkinson bar method or the one bar method had been predicted on the basis of the research conducted by the analysis group. (NEDO)

Report on achievements in proliferation project to assist introduction of environment harmonizing type coal utilization system in fiscal 1998. Joint demonstration project for CMG recovery and utilization system in fiscal 1998 (utilization facilities); Kankyo chowagata sekitan riyo system donyu shien nado fukyu taisaku jigyo seika hokokusho. 1998 nendo CMG kaishu riyo system kyodo jissho jigyo (riyo setsubi)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

This paper describes the achievements of the discussions in fiscal 1998 on the utilization facilities related to the coal bed methane gas supply plan for the city of Tieling in China. The gas quality standard calls for 3,500 kcal/m{sup 3} or more (methane concentration of 41% or higher). The supply is planned to start in December 1999, and continue the supply of 141,000 Nm{sup 3}/day in 2000, and 212,000 Nm{sup 3}/day in 2001 and thereafter. A gas supply center to collect gases recovered from each mine will be installed in the vicinity of the existing gas holder located about 2 km east of the Tiefa Mining Bureau. The Japanese side bears the cost of installing a gas compression and transportation facility for gas supply to the city of Tieling, a monitoring system, and devices for comprehensive surveillance system. This paper shows the overall plan drawings, the drain separator room building plan, the plans for arranging devices in the machine room, and the piping scheme. In addition, the piping plan around the gas holder, and the basic device plan are shown. Also appearing in the paper are the machine summary drawings, summarized flow charts, gas holder plan, de-humidifier plan, and electricity and instrumentation plans. The main body and supporting structure for the gas holder, and the foundation strength calculation sheets are also shown. Descriptions are given also on the facilities to deal with variation in demand quantity and supply quantity. (NEDO)

Report on survey project for demonstration of warm sea water bathing facilities using unutilized resources such as wastes in islands by carbonizing them into energy; 2001 nendo kankyo chowa gata energy community field test jigyo chosa hokokusho. Rito ni okeru haikibutsu tou mikatsuyo shigen no tanka energyka no kaisui on'yoku shisetsu heno jissho chosa jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-05-01

Surveys and discussions have been performed in Yuge Town in Ehime Prefecture for aiming at promotion of district development and zero emission in islands by carbonizing general wastes (household refuses and business operation wastes) and bamboos in the islands to utilize their energies as a substitute for the heat source of the warm sea water bathing facilities, as well as utilizing the produced carbides as soil improving materials or deodorants. The surveys were performed on bamboo carbonizing and gas carbonizing technologies, energy utilization feasibility, analysis of wastes composition, and identification of quantity of bamboos in existence. In discussing the energy utilization system by means of carbonization, it was revealed that the introduction of the bamboo carbonizing and gas carbonizing technologies can sufficiently satisfy the heat demand of the Yuge Town community facilities, although the amount of heat that can be supplied may vary because of difference in the technical processes. Also with regard to the problems of dioxins contained in the discharged gas and the problems of heavy metals contained in the carbides, it was discovered that different environmental criteria can be met as evidenced by the existing demonstration data. (NEDO)

Report on achievements in proliferation project to assist introduction of environment harmonizing type coal utilization system in fiscal 1998. Joint demonstration project for CMG recovery and utilization system in fiscal 1998 (recovering facilities); Kankyo chowagata sekitan riyo system donyu shien nado fukyu taisaku jigyo. 1998 nendo CMG kaishu riyo system kyodo system kyodo jissho jigyo (kaishu setsubi)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

This paper describes the achievements of the discussions in fiscal 1998 on the recovering system for coal bed methane gas to be supplied to the city of Tieling in China. The paper puts on record the associated documents, and figures and drawings. The associated documents appearing in the paper include the table for explosion-proof examination on the recovering devices, a parts list for the RK-3A type test drilling machine, and its operation manual. Specifications for the test drilling machine (including those for the sealing pumps), specifications for the mouth facilities, and device lists are shown. Test drilling device arrangement drawings and standard drilling record table are also described. Central blower specifications, a back-fire preventing device, a device to prevent well exterior from freezing, and a summarized drawing for drain remover for gas induction for the Daixing mine are explained. The schemes for induction and sealing, specifications and procedures for observation devices are shown. Specifications for sealing materials and the centralized monitoring facilities are also touched on. The safety measures, measures taken for power failure in the centralized monitoring facilities, and the control organization are described. Test drilling cost simulation and environment assessing methods are also described. The figures and drawings presented include the topographic map, Daixing mine cavity drawing, pipeline network, and chart for representative test drilling columns near the coal beds were also presented. (NEDO)

Project to promote the technical development of global environmental industries. International research exchange project; Chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo. Kokusai kenkyu koryu jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Exchanges with researchers/research institutes in overseas countries have an important meaning in promoting the research and development toward the creation of new research fields where the solution to the environmental problem is aimed at and toward the construction of new technological systems. Therefore, under the cooperation of Research Institute of Innovative Technology for the Earth (RITE), and RITE related researchers and societies, given were invitation and dispatch of researchers to international conferences and symposia involved in the global environment related technology, and exchanges with major overseas research institutes/universities. At the same time, based on the short-term invitation and dispatch so far given, a system was established for medium- and long-term dispatch/invitation of researchers who are thought to hold an important position in the future research activities. From the results obtained, domestic and foreign exchanges relating to the latest research could be promoted. In addition, researches in the basic domain related to the global environmental technology were advanced in a variety of fields overseas. The numbers of invitation and dispatch given in fiscal 1995 were 12 and 13, respectively, the results of which were included in this paper. 121 refs., 74 figs., 11 tabs.

Fiscal 2000 achievement report on the venture business assisting type regional consortium - Core industry creation type. Thermoelectric energy recovery system for automobile; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Jidoshayo netsuden energy kaishu system

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The project aims to develop a system for recovering heat from the thermal energy of automobile exhaust in the form of electric energy. Skutterudite based thermoelectric materials for high temperature use and existing thermoelectric materials for low/middle temperature use were improved in performance, and a dimensionless thermoelectric performance index of ZT=1 was attained. Advanced processes were applied for improvement on the performance of existing thermoelectric materials. In the effort to develop technologies for the mass production of thermoelectric materials for high temperature use, a material manufacturing process was established for manufacturing materials excellent in thermoelectric and mechanical properties using a method for mass-producing sinterable materials by gas atomization and a large discharge plasma sintering process capable of treating large specimens. In the effort to improve automobile power generation modules in performance and to establish element technologies for their manufacture, technologies were developed involving thermoelectric materials and electrodes, bonding of different thermoelectric materials, bonding of heat conducting electrical insulators and electrodes, and high efficiency segment type power generation modules. A high performance automobile exhaust gas heat exchanger was developed. A Co-Sb based thermoelectric module and a Bi-Te based module were combined and the package was tested aboard automobiles, when a maximum power output of 83W was achieved. It is necessary to review module arrangement. (NEDO)

New Sunshine Project for fiscal 1997 on the international cooperation project. Cooperation in solar energy technologies among Japan, Australia and other countries; 1997 nendo new sunshine keikaku kokusai kyoryoku jigyo. Nichigo nado taiyo energy gijutsu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This paper describes the state of progress in the cooperation in solar energy technologies among Japan, Australia and other country, the memorandum concluded for the new project, and the activity report on the NEDO/MUERI project. The progress in the cooperation in solar energy technologies among Japan, Australia and other country is divided into that of the new project and that of the continued project. The former relates to the start of the long-term endurance test project for photovoltaic solar modules in Oman. The location of the endurance test is the Sultan Qaboos University in the suburb of Muscat. Modules subjected to the endurance test consist of ten modules of five types. The test will be performed on air temperature, humidity, wind directions, insolation on horizontal surface, insolation on slanted surface, ultraviolet ray intensity, module temperatures, and electric characteristics of the modules. The continued project is an outdoor endurance test for the photovoltaic solar modules begun in fiscal 1996, which is executed by the Murdock University Energy Research Institute (MUERI). The endurance test locations were selected at Darwin, Alice Springs and Perth. This paper reports the photovoltaic solar module endurance test and investigation, as well as the periodical consultations as the activity report of the NEDO/MUERI project. (NEDO)

Fiscal 2000 feasibility research on environmentally friendly coal utilization system. Seminar holding project (China: Zaozhuang, Yanshan, Jianshan, Jinzhou); 2000 nendo kankyo chowagata sekitan riyo system kanosei chosa hokokusho. Seminar kaisai jigyo (Chugoku Zhaozhuang, Yanshan, Jianshan, Jinzhou)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Seminars were held in China for the delivery of reports on the results of model projects with a view to popularizing the results of the clean coal technology model projects, which had been completed, for the purpose of contributing to the improvement on coal utilization technology and to the enhancement of environmental protection. The seminars took place at the sites of demonstration model projects just completed in China, namely, Zhejiang Huba Corporation (low-grade coal combustion system); Chaili Colliery, Zaozhuang Coal Mining Administration (CFBC - circulating fluidized bed combustion); Jinzhou Heat Power General Co., Ltd. (CFBC); and Beijing Yanshan Petrochemical Corporation (desulfurizing agent-added coal-water mixture system). At each of the project implementation sites, lectures were given on technical matters, technical know-how was exchanged, and study tours were organized to facilities concerned, which meant to promote the diffusion of the related technologies throughout China and, eventually, to contribute to the enhancement of environmental protection. The main subjects at the seminars included the introduction of GAP (green aid plan) projects in China, introduction of the outlines of technologies related to the model projects, verification and achievements, latest trends, and measures for the diffusion of the technologies. Study tours were made, and videos were shown relating to the local conditions. Every one of the seminars was successfully attended by 60-70 participants. (NEDO)

FY 2000 report on the results of the joint research - Field test project on the photovoltaic power generation for public facility use; 2000 nendo kyodokenkyu gyomu seika hokokusho. Kokyo shisetsu you taiyoko hatsuden field test jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-05-01

The paper arranged the FY 2000 results of the field test on the photovoltaic power generation for public facility use, etc. This report described in detail the results obtained at 237 places including the following: Social Welfare Corp. Seimei-kai, Kobe City (Hyogo Prefecture), Iitaka Town of Iinan County (Mie Prefecture), Kyushu Electric Safety Association, Educational Corp. Kongo Gakuen, Social Welfare Corp. Izumi-kai, Educational Corp. Shiobara Ikuei-kai, Educational Corp. Aiko Gakuen, Social Welfare Corp. Tachibana-kai, Cooperative Association Co-op Kobe, Social Welfare Corp. Hoshizuki-no-sato, Tochigi-Fuji Industrial Co., Hirabayashi Section of Gamo Town of Gamo County (Shiga Prefecture), Yanagawa City (Fukuoka Prefecture), Imadate City of Imadate County (Fukui Prefecture), Osaka Prefecture, Yamanashi Prefecture, Utazu Town of Ayauta County (Kagawa Prefecture), Educational Corp. Fukuyama Gakuen, New Energy Business Cooperative Association, Meitec Corp., Shikoku Medicom Co., Shizen Kobo Co., Educational Corp. Horikoshi Gakuen, Matama Town of Nishi-Kunisaki County (Oita Prefecture), Nio Town of Mitoyo County (Kagawa Prefecture), Educational Corp. Koshien Gakuin, Sansei Giken Co., Mitsui Greenland Co., AWI Mach Co., Nagoya City and Educational Corp. Kibogaoka Gakuen. (NEDO)

Fiscal 2000 project for development of international standards for supporting novel industries. Standardization of methods for testing and evaluating pure titanium; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo. Jun titan no shiken hyoka hoho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of submitting propositions to ISO (International Organization for Standardization)/TC79 (Light metals and their alloys) and ISO/TC135 (Non-destructive testing), studies were made relating to the standardization of methods for chemical ingredient analysis and non-destructive testing of industrial pure titanium. In the development of an ingredient analysis method for pure titanium, performance standards and analytical allowance were determined for an inductively coupled plasma emission spectrochemical analyzer for vanadium, niobium, cobalt, and boron, which were short of completion in the preceding fiscal year. As for spark discharge emission spectrochemical analysis, analysis methods were newly established for oxygen and hydrogen. In the development of optical flaw detection for pure titanium boards, the quality of test pieces were determined by use of a reference test piece, and studies were made about the kinds of artificially produced flaws and a method for sensitivity calibration. In the development of ultrasonic flaw detection for pure titanium boards, studies were made about the effects of board thickness, kinds of flaws, and of board size. Using the findings, a draft standard was prepared in Japanese for a JIS (Japanese Industrial Standards) proposition and another in English for an ISO proposition. (NEDO)

FY 1999 report on the results of the joint study - project on the industry use photovoltaic power generation field test. 2/3; 1999 nendo sangyonadoyo taiyoko hatsuden field test jigyo kyodo kenkyu seika hokokusho. 2/3

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

In the field test, solar cell panels were installed on rooftop, and inverters were installed indoors. The electric power generated was connected at high pressure with electric installation of facilities and was also supplied to power equipment, lighting, air conditioning, etc. in facilities. The FY 1999 results were summarized. The installation of photovoltaic power generation facilities at 38 places and the results of the study were summarized in this report including a new public office building of Nio town, Kagawa prefecture, General Welfare Center of Matsumae town, Ehime prefecture, General Culture Center of Nakajima town, Ehime prefecture, Educational Foundation Sugao School, Training Center of Japan Railway Co., etc. (NEDO)

FY1992 research report on the evaluation and analysis of data collected in fuel cell power generation field test project; 1992 nendo nenryo denchi hatsuden field test jigyo ni okeru shushu data hyoka kaiseki kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

This paper describes the achievements in fiscal 1992 in the field tests on fuel cell power generation systems. The three locations subjected to the present analysis are all installed with 50-kW systems, whereas power generation efficiency of around 35% such as 35.3, 34.2 and 34.6% was obtained when the systems were operated at the rated output. When the load gets to below a certain load band (about 30 kW), the power generation efficiency decreases proportionately with the load. The overall efficiency including heat supply was 77.8, 70.7 and 80.3% respectively at about the rated output, showing a trend that the higher the thermal efficiency, the higher the overall efficiency. The case of generating both electric power and heat simultaneously has higher efficiency than the case of heat supply alone. The contribution rate of the fuel cell as a base load was 2.8, 4.6 and 13.6%, respectively. The system with as high value as 13.6% takes a power load following type operation mode, in which power is generated during a time band with large load during weekdays, and no power is generated at nighttime and in holidays when load is smaller, playing a role of peak responding power supply. Only one trouble has occurred in an auxiliary generator in the heat recovery system. (NEDO)

Fiscal 1996 research report. Basic research on energy consumption efficiency improvement for developing countries (Industry related survey for energy analysis); 1996 nendo hatten tojokoku energy shohi koritsuka kiso chosa jigyo hokokusho. Energy bunsekiyo sangyo renkan chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-05-01

Inter-industry relations tables and energy statistics are combined for Asian countries for the preparation of energy analysis oriented inter-industry relations tables, which are used to metrically analyze Aisan nations' industrial structures and energy consumption structures for the ultimate purpose of grasping the magnitude of each industry's demand for energy. The tables prepared this year cover Korea, Indonesia, Thailand, and the Philippines. In Korea, the self-sufficiency rate of mineral fuels is low at 23.1%, which is due to its import of crude oil from abroad. It consumes 177.92-million tons (in terms of oil) of energy for its economic activities, with energy saving measures expected to work effectively here. Indonesia's mineral fuel self-sufficiency rate is high at 84.3% because it is an oil producing country. The energy it consumes for its economic activities is 179.37-million tons (in terms of oil), and energy saving measures will work effectively here. Thailand is a crude oil importing country. Its mineral fuel self-sufficiency rate is 33.4% and the energy its economic activities consume is 53.08-million tons (in terms of oil), and energy saving measures will work effectively in this country. The Philippines is a crude oil importing country and its mineral fuel self-sufficiency rate is as low as 4.8%. It consumes 22.71-million tons of energy (in terms of oil) for its economic activities, and energy-saving measures are expected to take effect here. (NEDO)

Fiscal 1995 international research cooperation project. Report on the R and D result of the environmental harmony type combustion technology; 1995 nendo kokusai kenkyu kyoryoku jigyo. Kankyo chowagata nensho gijutsu ni kansuru kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The research and development were conducted jointly with Europe of an environmental harmony type high efficient catalyst which enables clean combustion and NOx removal in polluted gas in combustion flue gas, etc. In the research and development of NOx removal catalyst such as zeolite base, reformation of mostly mordenite was done by ion exchange, ion implantation, skeleton element substitution, etc. A possibility was found out of applying the membrane formation method except ion implantation as reforming means. In the R and D of the complex oxide base NOx removal catalyst, it was found that the catalyst carrying copper and silver on silica and layer clay compound under optimum conditions shows peculiarly high activity, and there is little decrease in the activity, but rather increase in it even under vapor existence. An evaluation was made of NO resolution of direct resolution element carrying noble metal electrolyte on solid electrolyte, finding out that the highest NO selectivity is shown with Pd as electrolyte and at a baking temperature of about 1300degC. Development of high- and low-temperature catalysts was also made. 417 refs., 286 figs., 63 tabs.

Report of base consolidation promotion survey of overseas coal import in FY 1993. Feasibility survey of effective utilization of coal ash; 1993 nendo kaigaitan yunyu kiban seibi sokushin chosa. Sekitanbai yuko riyo jigyo no feasibility chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

This report describes the effective utilization of coal ash discharged from general industry (general industry ash) as improving material of construction waste soil and deodorant for poultry industry. Coal ash is characterized by the pozzolan and self-hardening properties which are not shown in soil and sand. Coal ash having a large amount of free CaO in its composition has stronger such properties. Coal ash generated from fluidized bed combustor which is a kind of combustor of coal contains a large amount of free CaO, especially, resulting in the stronger such properties. On the other hand, coal ash has water and oil absorbing property due to its porous structure. To utilize these properties, the improving material of soft construction waste soil and deodorant for poultry industry have been selected. As a result of laboratory and field tests for the former, it was found that sufficient supporting force can be obtained. Since the protection of powder splash is required at the site, a humidification system has been developed, which can protect the splash by the humidification of 5%. The price between 500 and 1,000 yen/ton is suitable for the improving material of construction waste soil. The maximum price of the deodorant for poultry industry is 10 yen/kg. 14 refs., 40 figs., 49 tabs.

Fiscal 1996 international research cooperation project. Report on the R and D result of the environmental harmony type combustion technology; 1996 nendo kokusai kenkyu kyoryoku jigyo. Kankyo chowagata nensho gijutsu ni kansuru kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The research was conducted jointly with Europe of a catalyst which enables clean combustion and NOx removal in polluted gas in combustion flue gas, etc. Reformation of mordenite and {beta}-zeolite was done by ion exchange, ion implantation, and membrane formation. A catalyst was searched for to obtain reducing agents, C5-C8 components, by decomposing light oil. Saponite, clay compound, showed by copper and silver ion exchanges approximately 50% of activity under 20,000h{sup -1}, C3H6 reducing agent, and without steam. The effect of the temperature of sintering on NOx selective reductionality of silver-carrying alumina catalyst was studied, and in sintering at 800degC, activity increased. When using conductive oxides like ruthenium oxide for electrolyte, NO decomposition selectivity increased. As to the functional layer carried above the Pd electrolyte, iron oxide and magnesium oxide increased NO decomposition selectivity. PdO and rare earth oxides forming compounds controlled variation of activity by dissociation/reoxidation of PdO. As to PdO/Gd203, the initial methane combustion activity was favorable, but there was seen deterioration with age. 271 refs., 281 figs., 58 tabs.

Fiscal 2000 project for development of international standards for supporting novel industries. Standardization of management of color reproduction (Color management); 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo. Iro saigen kanri (color management) no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Studies were made to formulate a standard plan on color information apparatuses and prepare software programs to be responsible for their characteristics and to draft propositions on international standards based on them. In the effort to standardize color control for input/output apparatuses, factors causing fluctuations in the profile were extracted, and hierarchical function expansion was implemented for the profile including elementary color augmentation. The draft on standardization was presented at a conference held at San Jose, U.S. As for the standardization of the multispectral color image description format, a fluorescent color atlas was prepared and presented at ISO/TC130 Conference in September, when it was accepted that it be a proposition at the next conference. In the standardization of psychological color reproduction, a 2-stage evaluation system was established, capable of achieving a result high in accuracy and stability under a small experimental load. This methodology of subjective evaluation was presented at ISO/TC42/WG18 Tokyo Conference, when it was requested that it be a new item on the agenda. (NEDO)

Basic investigation on promotion of joint implementation in fiscal 2000. Modernization project for North Bangkok Thermal Power Plant in Thailand; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Tai North Bangkok karyoku hatsusensho kindaika jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective of saving energy and reducing greenhouse gas emission, a modernization project has been discussed on the North Bangkok heavy oil burning thermal power plant owned by Electricity Generating Authority of Thailand (EGAT). The present project plans to withdraw the existing units No. 1, 2 and 3, and install two new generating facilities with the rated output of 358.3 MW using natural gas as fuel. The present feasibility survey has performed detailed comparative discussions on four cases, whereas a proposal was selected to withdraw all of the boilers, steam turbines, and generators, and install two single axis combined cycle systems whose output has been increased by using the existing fuel tank area. The energy saving effect by this project can reduce fuel consumption annually by 514 kt of crude oil equivalent. The greenhouse gas can be reduced annually by 2,680 kt-CO2. The project will require a total fund of about 57 billion yen. The profitability assessment calls for the internal profitability of 8.413% and the investment fund efficiency of 1.69%. The economic investment payback effect of this project is determined sufficient. (NEDO)

FY 1999 report on the results of the joint study - project on the industry use photovoltaic power generation field test. 1/3; 1999 nendo sangyonadoyo taiyoko hatsuden field test jigyo kyodo kenkyu seika hokokusho. 1/3

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

In the field test, solar cell panels were installed on rooftop, and inverters were installed indoors. The electric power generated was connected at high pressure with electric installation of facilities and was also supplied to power equipment, lighting, air conditioning, etc. in facilities. The FY 1999 results were summarized. The installation of photovoltaic power generation facilities at 88 places and the results of the study were summarized in this report including Social Welfare Corporation Seishoen, Maruto Co., Saga Sanyo Industries Co., Koyama Cranial Nerve Surgery/Internal Medicine Hospital, Tsuchiura Urban Development Co., Osaka Alloy Works, Suntory Limited, etc. (NEDO)

FY 1999 report on the results of the joint study - project on the industry use photovoltaic power generation field test. 3/3; 1999 nendo sangyonadoyo taiyoko hatsuden field test jigyo kyodo kenkyu seika hokokusho. 3/3

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

In the field test, solar cell panels were installed on rooftop, and inverters were installed indoors. The electric power generated was connected at high pressure with electric installation of facilities and was also supplied to power equipment, lighting, air conditioning, etc. in facilities. The FY 1999 results were summarized. The installation of photovoltaic power generation facilities at 39 places and the results of the study were summarized in this report including a community hall of Iwade town, Wakayama prefecture, Sugihara Industrial Co., a public library of Mabi town, Okayama prefecture, Social Welfare Corporation Shofukai Aiwaen, Japan Kodo Paper Industries Co., etc. (NEDO)

FY 1998 evaluation/analysis of the data collected in the field test project for photovoltaic power generation for public facilities; 1998 nendo kokyo shisetsu nadoyo taiyoko hatsuden field test jigyo ni okeru shushu data hyoka kaiseki

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In the field test project for the photovoltaic power generation for public facilities, operational data were collected/analyzed on facilities at 158 sites installed from FY 1994 to FY 1997. As a result, the following were found out: Average values of the global radiation on an inclined surface, equivalent array operation time, equivalent system operation time, system operation time, inverter performance efficiency, inverter load factor, array power coefficient, and system power coefficient are 3.51 kWh/m{sup 2}/D, 2.72 h/D, 2.47 h/D, 10.3 h/D, 0.91, 0.30, 0.77 and 0.70, respectively. No deterioration with age was recognized in the 4-year operation data. As to the maintenance, the item, 'there are a lot of failures in the photovoltaic power system,' was 2% in rate. As to the inspection, times are mostly once a month. The annual maintenance cost was widely between about 360 yen/kW and about 30,000 yen/kW. Supposing annual expenses to be a total of capital expense, direct expense, and general administrative expense, the power generation cost dropped from approximately 240 yen/kWh in FY 1994 to 100 yen/kWh in FY 1997. (NEDO)

FY 1998 annual report on the survey on overseas geological structures. Project for exchanging engineers (coal mining technology area) (Vietnam); 1998 nendo kaigai chishitsu kozo nado chosaa. Gijutsusha koryu jigyo (tanko gijutsu bun'ya) (Vietnam)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The project for exchanging engineers has been implemented, in order to improve production and managemental techniques of coal mining engineers in the Asia-Pacific region, promote smooth and efficient projects for surveying overseas geological structures, and facilitate stable supply of overseas coal to Japan. The FY 1998 project was concentrated on Vietnam, to which Japanese coal mining engineers were sent, and from which production management engineers were invited to Japan as trainees. The Japanese engineers sent to Vietnam educated the underground coal mining techniques. The Vietnamese management engineers invited were trained for, e.g., production management techniques (e.g., those for workplaces and organizations) in the Japanese mines, administrative management techniques, and techniques to improve safety and productivity in the mines. Coal Energy Center and Taiheiyo Mining's Kushiro Mine provided training facilities. (NEDO)

Fiscal 1997 technological survey report. Engineer exchange project - coal mine technological field (Advanced coal producing country survey - U.S.A. survey); 1997 nendo gijutsusha koryu jigyo (tanko gijutsu bun'ya) senshin santankoku chosa. Beikoku chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

While the introduction and adaptation of the Longwall excavation technology were carried forward for coal producing countries in the Pacific region, U.S.A. information was collected by making tours of coal mines in the West and Washington/Colorado/Utah States, with the intention of ascertaining technological trend so as to carry out efficient technological transfer, and for the purpose of replenishing the contents and contributing to the smooth implementation of the engineer exchange project in 'coal mine technological field'. The coal reserves are 400 billion tons, with 840 million tons produced and with 80 million tons exported; not less than 56% of the U.S. domestic electricity rests on coal. Production by open-pit mining is the majority while the output by underground mining is 38%; the Longwall method has increased as a digging method, taking 18% of all digging output. The productivity is 4.24 ton/person per day and ranks as the world highest. The coal mining technological trend in the U.S. can be summarized as follows. The coal mining output in the West is increasing, with the number of mines decreasing, so that the output per mine is increasing. With the output ratio by open-pit mining increasing, the digging method in the mine is being changed to the Longwall. (NEDO)

FY 2000 report on the investigational study of the introduction/spread of clean energy vehicles for transportation business use; 2000 nendo chosa hokokusho. Unso jigyo yo clean energy jidosha no donyu fukyu ni kakawaru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A comparative study of the cost effectiveness in improvement of emission gas was made between the diesel particulate filter (DPF) which is studied as measures against toxic emission gas from the vehicles already sold and the compressed natural gas (CNG) vehicle which has a large number of spread among clean energy vehicles. In the trial calculation, 18 cases were set up using measures by year against diesel car emission gas, use period and annual running distance as valuables. As a result of the study, the following conclusions were obtained. At the present time, when the vehicle price dropped approximately 40% from that at the beginning of the introduction, the cost effectiveness of CNG vehicle is larger than that of diesel car with DPF. Since the unit price of natural gas is comparatively higher than that of light oil, the longer the annual running distance is, the smaller the cost effectiveness of CNG vehicle is than that of diesel car with DPF. The durability period of DPF is considered not so long, and therefore, the longer the use period is, the larger the cost effectiveness of CNG vehicle is than that of diesel car with DPF. (NEDO)

Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium field / R and D on downsizing technology of machine tools (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium energy bun`ya / kosaku kikai no downsizing gijutsu ni kansuru kenkyu kaihatsu (daiichi nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The R and D were conducted aiming at downsizing machine tools by combining microfactory technology owned by Mechanical Engineering Laboratory, Agency of Industrial Science and Technology of MITI with fundamental element technology owned by industrial groups of machine tools. In fiscal 1997, as to the study of spindle drum indexing mechanism in making main spindle multiaxial, the following have been finished: the basic study through openness of controller and networks, confirmation of function of the equipment acquired, and initialization of the driver software. Relating to the study on machining conditions of dry machining processing, delivery and installation of cold air machining instrument have been finished. Concerning the optical measurement of spindle radial run-out vectors, a system to make optical no contact measurement of radial direction components of rotation error was constructed with high accuracy pin gauge attached to the work spindle clamp mechanism as a medium. About the study on sensor-based state recognition technology, specifications for various kinds of sensor were decided on. 5 refs., 67 figs., 3 tabs.

Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium energy field/R and D high performance flat panel display technology (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium energy bun`ya / koseino flat panel display gijutsu no sogo kaihatsu kenkyu (daiichi nendo ) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

One of the subjects in technology supporting the highly information-oriented society which will develop and diversify toward the 21st century is the construction of high grade man/machine interface. For it, high precision/high luminance/energy saving/thin plane displays are strongly requested. This R and D is to indicate models of systematical development in the region of element technology individually existing in the Shikoku area by forming a regional consortium in the industry/universities/government. Creation of new industries by gathering display related enterprises is a first step in a plan to realize `Display Island Shikoku.` As a concrete target, with the use of high-tech diamond semiconducting technology, a development is conducted of the high performance flat panel display using the negative electron affinity (NEA) electron emitter which drastically solves the problems such as luminance, visibility angle and response speed, the subjects on the commercialized liquid crystal flat panel display. 16 refs., 45 figs., 8 tabs.

Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium energy field / development of nano-structured materials for ceramic bearing application (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium energy bun`ya / ceramic bearing yo nano seigyo zairyo no kenkyu kaihatsu (daiichi nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For the purpose of developing high efficient ceramic bearing using nano-structured materials, technical development was proceeded with of raw material powder treatment, forming sintering, processing, structural analysis, property evaluation, etc. As to the study of manufacturing of ceramic balls, the following were conducted by the method developed at Osaka Prefectural Institute of Industrial Technology: coprecipitation laminate processing of ZrO2-Al2O3 system to alumina powder at Okumura Crucible Mfg. Co. Ltd., spherial press processing and sintering at Kyocera Co. Ltd., and precise machining at Nippon Pillow Block Mfg., Co. Ltd. The performance as bearing was measured of the ceramic balls obtained such as surface coarseness, sphericity, crush strength and fatigue life. Surface coarseness and sphericity were the same as those of bearing use silicon nitride, but crush strength was considerably low. In the experiment on rolling fatigue strength as bearing, separation occurred within 100 hours even at a load of 100kgf. It is thought that this is because of the pores remaining on the surface, and the measures to be taken for long life were studied. 12 refs., 64 figs., 27 tabs.

Report on the results of the FY1999 standardization for new standard interface protocol for electrical measuring use; 1999 nendo shinki sangyo ikusei sokkogata kokusai hyojun kaihatsu jigyo seika hokokusho. Denki keisokukiyo shinhyojun interface purotokoru no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The purpose of this project is to create a new protocol for electric measuring instruments that use a built-in the Universal Serial Bus (USB) interface which is no incorporated in PCs. This new interface will replace the existing GPIB interface (IEEE-488), which is currently used in electric measuring instruments as standard interface. Our goal is to create a protocol that will provide the same data rate as GPIB and better connectivity. To evaluate our new protocol, we create virtual instruments using evaluation boards for USB chips, as well as software, and performed transfer tests to isolate and solve problems found in the tests. We will make the protocol and the software available for general use, and register the protocol as a standard to the USB Developer's Forum, a body that manages USB standards, to make it as a de facto standard. Ultimately we are aiming at making it an international standard. (NEDO)

Report for fiscal 1998 on industrial waste optimized treatment technologies dissemination and promotion business for asian region. Holding a symposium; 1998 nendo chosa hokokusho. Asia chiiki sangyo haikibutsu tekiseika shori gijutsu nado fukyu sokushin jigyo (symposium kaisai)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

An International Symposium on the Asian Industrial Waste Issue was held in Tokyo on 4 February 1999, where lectures were delivered by participants representing China, the Philippines, Thailand, Malaysia, and Japan. More 150 people attended the event, with questions and answered animatedly exchanged between the lecturers and the audience. The progress of urbanization is quite rapid in China, with the quantity of waste increasing every years to justify the anticipation that there will be a very sharp increase in refuse incineration in the near future. Raising a serious problem in China these days is the plastic waste. In the Philippines, there are no private-sector waste treatment/disposal facilities and corporations are not obliged to take care of their waste. Consequently, very little treatment or recycling is being undertaken. In Thailand, although waste treatment/disposal centers are in operation financed by the Government and private sectors, the cost is very high, and the Government policy is that private investment will be encouraged and supported in future. In Malaysia, privatization is in progress of the business of managing waste in the solidified form. A comprehensive waste treatment/disposal plant was completed in 1998 by the endeavors of a Denmark-Malaysia consortium, and is in operation since then. (NEDO)

FY 1999 report on the results of 'the model project for effective utilization of the waste heat discharged from the combustion of paper-manufacturing sludge'; 1999 nendo seika hokoku. Seishi surajji nensho hainetsu yuko riyo moderu jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of reducing the consumption of fossil fuel and reducing emissions of global warming gases in Malaysia, a model project for thermally effective use of the sludge discharged from paper-manufacturing plant was carried out. Concretely, the paper-manufacturing sludge discharged from paper-manufacturing plant is to be dewatered and improved of its lower heating value. Then, the sludge is to be burned in fluidized bed incinerator, and the steam is to be generated by recovering heat using waste heat recovering boiler. The steam obtained is to be used as process steam of the plant. In this fiscal year, the first year of the project, the attachment to the agreement was prepared in terms of the allotment of the project work between Japan and Malaysia, various kinds of gist, schedules, etc. and signed. After that, the determination of the basic specifications for facilities was made according to the attachment to the agreement. Now, the basic design of the whole plant is being made. The design of the process flow sheet, design of the layout plan for plant equipment, etc. were finished. The goods to be purchased are now being estimated and assessed. Moreover, as to the civil engineering/construction design, drawings of the basic design are now being made. (NEDO)

Fiscal 1999 report on result on the model project for systematization of high-efficiency combustion of by-product gas in ironworks. Part 2/2; 1999 nendo seitetsusho fukusei gas kokoritsu nensho system ka model jigyo. 2/2

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-09-01

For the purpose of reducing energy consumption of the steel industry, a large energy consuming industry in China, a model project was carried out for systematization of high-efficiency combustion of by-product gasses in ironworks, with the fiscal 1999 results compiled in the form of detailed design/documents, and the like. This project is intended for demonstration and dissemination of technologies for improving energy consumption efficiency, by controlling mixed gas calorie and oxygen content, in the reheating furnaces that consume as fuels various combustible gasses produced in iron and steel making processes. Arranged in the detailed design documentation were numerous drawings including a list of mixed gas equipment, design drawing of mixed gas orifice, specification of mixed gas control valves, list of reheating furnace equipment and devices for No.1 small plant, specification of control valves of reheating furnace for No.1 plant, list of reheating equipment and devices for slab plant, specification of calorimeter, specification of oxygen concentration meter, No.1 mixed gas wiring system diagram, and No.3 mixed gas piping/assembling manual. Also prepared were a manual for pre-shipment inspection and report on inspection findings, as well as notes on transportation, program for receiving Chinese engineers, schedule for dispatching engineers, etc. (NEDO)

FY 2000 report on the results of the project to promote the comprehensive management of petroleum products. Development of a risk assessment system; 2000 nendo sekiyu seihin sogo kanri suishin jigyo seika hokokusho. Risk hyoka system kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The R and D were conducted on the system to assess risk of chemicals which considers the human health, environment, etc., and the FY 2000 results were reported. In this fiscal year, the goal of the study was to establish a system of user-friendly interface, easy-to-use system components and data access methodology. As to the details of the system, additional assessment items on the human health were found and surveyed, and the development of a new system for the assessment of acute exposure was started. Relating to the handling of various data on toxicity, physical properties, etc., reference is to be made to the database of National Institute of Technology and Evaluation, MITI, as a base. Concerning the simple assessment corresponding to the PRTR method, almost all 435 chemicals designated by the PRTR act were to be included in the internal database. As to the development of the system, the simple assessment system corresponding to the PRTR method was developed, and a testing system, {beta} version, was completed. Further, the development of a 'site-specific assessment system' was started which considers the geological/meteorological situation of the site. (NEDO)

Basic project on the cooperation in enhancement of the international energy consumption efficiency. Survey of energy conservation potential by industry; 2000 nendo kokusai energy shohi koritsuka chosa nado kyoryoku kiso jigyo hokokusho. Gyoshubetsu sho energy potential chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of looking for measures to promote the effective energy conservation in China, the potential energy conservation amount in general plants was surveyed and analyzed by industry. Activities were made in the following fields: 1) survey of the actual state of energy in main industries; 2) energy conservation potential in the cement industry in China; 3) energy conservation potential in thermal power plants in China. In 1), survey was made on 8 industries including the iron/steel industry and oil refining industry. In 2), survey was made of the actual state of the Liulihe cement plant and Shitou cement plant. The subjects extracted were the arrangement of instrumentation equipment such as the exhaust gas analyzer needed for combustion management, improvement of the air/fuel ratio of kiln, enhancement of cooling efficiency of clinker cooler, etc. In 3), the actual state of the Qinling power plant was surveyed, and it was made clear that high efficiency of 38% or more can be maintained if the appropriate use/maintenance management is made (coal unit consumption: 383g/kWh in Qinling and 309g/kWh). (NEDO)

Report on the FY 1998 geological structure survey. North Hay Gulch area, State of Colorado, the U.S.; 1998 nendo kaigaitan kaihatsu kanosei chosa hojo jigyo chishitsu kozo chosa hokokusho. Beikoku Colorado shu North Hay Gulch chiiki

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-02-01

Test boring at 21 places and core sampling were conducted during September-November 1998 along the ridge to the west of Hay Gulch and in the direction crossing the northwest of the drainage canal and National King Coal Mine (NKC coal mine). It was found that A layer which NKC coal mine is now drilling is the upper part of A coal seam where the seam bifurcates. The boundary to the west of the thick A coal seam is not clear, and there is a possibility that more reserve from the thick coal seam and single seam exists toward Cherry Creek. In the existing coal drilling area, the lower A seam existing under the upper A seam becomes thin rapidly, and the seam thickness becomes less than 1 foot. The average thickness of thick coal seams is 9.9 feet, and the area is 780 acres along the ridge. The upper A coal seam except the above is 5.5 feet in average seam thickness and 910 acres in area. The reserve is 23 million tons. As to the quality of thick coal seam, the average heating value is 7,089 kcal/kg, sulfur content 0.68%, and ash content 7.50%. As coal drilling conditions, the same level as or higher than those of NKC coal mine is expected. (NEDO)

FY 2000 report on the results of the project to promote the comprehensive management of petroleum products. Development of a risk assessment system; 2000 nendo sekiyu seihin sogo kanri suishin jigyo seika hokokusho. Risk hyoka system kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The R and D were conducted on the system to assess risk of chemicals which considers the human health, environment, etc., and the FY 2000 results were reported. In this fiscal year, the goal of the study was to establish a system of user-friendly interface, easy-to-use system components and data access methodology. As to the details of the system, additional assessment items on the human health were found and surveyed, and the development of a new system for the assessment of acute exposure was started. Relating to the handling of various data on toxicity, physical properties, etc., reference is to be made to the database of National Institute of Technology and Evaluation, MITI, as a base. Concerning the simple assessment corresponding to the PRTR method, almost all 435 chemicals designated by the PRTR act were to be included in the internal database. As to the development of the system, the simple assessment system corresponding to the PRTR method was developed, and a testing system, {beta} version, was completed. Further, the development of a 'site-specific assessment system' was started which considers the geological/meteorological situation of the site. (NEDO)

FY 2000 report on the results of the survey of the project for implementation of 'The New Earth 21'; 2000 nendo 'chikyu saisei keikaku' no jisshi keikaku sakusei ni kansuru chosa jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

As the research study contributing to implementation of 'The New Earth 21' proposed by Japan at the Houston Summit in 1990, a DNE21 model was developed as a quantitative assessment model for global warming preventive technology, heightening of efficiency of the global energy supply/demand system, conversion to energy sources of low carbon emissions, etc. In the project of 'The New Earth 21,' economy and environment can be compatible centering on developed countries' technical development and technology transfer to developing countries. In FY 2000, for heightening applicability of the DNE21 model, the world, which was used to be divided into 10 regions, was divided into 54. At the same time, a prototype model was constructed in which cities in the region were divided into three cities: large; medium; small. Using the DNE21 model, evaluation was made of effects of uncertainties such as population, economic growth, final energy demand and cost as preconditions of the model on the optimization of global warming preventive measures. Further, technologies which are expected to be important for global environmental policy in the ultra-long term were listed up to estimate the potentiality. (NEDO)

FY 2000 Project of developing international standards for supporting new industries. Standardization of systems for detecting gene recombination products; 2000 nendo shinki sangyo shiengata kokusai hyojunka kaihatsu jigyo seika hokokusho. Idenshi kumikae seihin kenshutsu system no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the FY 2000 results of the studies on the basic conditions for gene recombination products, and methods of determining content of the purchased gene recombination products in agricultural products, conducted to promote the standardization of the gene recombination product detection systems. Soybean is taken up as the gene recombination product to be studied, in which the samples containing the gene recombination product at 5, 0.5, 0.1 and 0% are prepared, and qualitatively analyzed by the DNA extraction and PCR method. No band is detected. For the quantitative examination by the real-time PCR method, the SYBRGeen, Taqman and hybridization probe methods are used to study the PCR conditions. The sample DNA extracted by the DNA Extraction kit for GMO Detection Ver.2 from the sample containing the RoundupReady{sup TM} soybean is quantitatively analyzed by the real-time PCR method for GMO content, which has produced the results for promotion of the standardization. (NEDO)

Fiscal 1999 international energy conservation model project. Report on result of demonstrative research concerning cement clinker cooling system; 1999 nendo kokusai energy shohi koritsuka nado model jigyo seika hokokusho. Cement clinker reikyaku sochi ni kakawaru jissho kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of reducing energy consumption and CO2 discharge in a cement plant in Indonesia, R and D was conducted on new clinker cooling system, high performance kiln combustion system, and technology for steady kiln operation and control, with the fiscal 1999 results reported. In the research on the optimum clinker cooling system, a new type clinker cooling system (CCS) was developed in which air beams are applied only to stationary grate rows, in an air beam type clinker cooling system where cooling air is fed to each block, with grate plates used as the air duct. This year, in an actual machine testing equipment (capacity 2,500 t/d), the whole heat recuperation area was modified for the CCS, with the operation started since February, 1999, aiming at the optimal clinker cooling effect and high heat recovery efficiency. The heat quantity for the entire system showed a decrease of 60 kcal/kg in the heat consumption rate through CCS modification, kiln burner adjustment, etc. So long as the demonstration plant is concerned, design of a new type burner and study/design for the kiln stabilization were nearly completed. (NEDO)

FY 2000 report on development of the infrastructure to promote use of fuel cells for automobiles. Standardization of FCEVs; 2000 nendo nenryo denchi fukyu kiban seibi jigyo jidoshayo nenryo denchi fukyu kiban seibi seika hokokusho. FCEV hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the results of the FY 2000 activities for standardization of fuel cell powered vehicles and development of the infrastructures related to participation in ISO. Fuel cell powdered vehicles are believed to be the most favored vehicles of the next generation for their low emissions and fuel efficiency. The world leading automakers, including Japanese makers, have announced plans to commercialize these vehicles in 2003 to 2004. Under these situations, the discussion has been initiated to move forward standardization of the fuel cell powdered vehicles at the international conferences, e.g., ISO (International Standardization Organization) and IEC (International Electrotechnical Commission). At ISO/TC22/SC21 (Electric Vehicles) for which the Japan Electric Vehicle Association (JEVA) is in charge as the domestic council, the proposal has been made and approved to begin working towards the standardization at the conference in November 1999. Consequently, FCEV special subcommittee consisting of public organizations (including academic organizations and Ministry of Economy, Trade and Industry), automakers, automotive parts manufacturers and other organizations related to the automotive industry has been established in February 2000 under the JEVA standardization section and started the activities. The Japanese proposals for safety and fuel cell vehicle terminology will be presented to the ISO meetings to be held in May 2001 in Tokyo. (NEDO)

FY 2000 report on the basic survey to promote the joint implementation. Project on the repair of the Bobovdol thermal power plant, Bulgaria; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Bobovdol karyoku hatsudensho kaishu jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

As to the Bobovdol thermal power plant, Bulgaria, a plan for repair of power plant was worked out with the aim of energy conservation and greenhouse effect gas emissions, and the results of the feasibility study were reported. The existing power plant, 3 x 210MW unit, totals 630MW, approximately 130,000 hours in cumulative operation hour. In the repair plan, the plant is replaced with high efficiency gas combined cycle power generation facilities based on gas turbines by scrap and build. In the plan, the repair of existing units Nos. 1 and 2 for life elongation is urgently conducted, and new facilities are to be built every 5 years. As a result of the study, the energy conservation effect will be reduced by 16.37 million toe tons in 41 years after the repair, and the CO2 emission will be reduced by 105.18 million tons in 41 years after the repair. As to the profitability, the internal economical profitability is 5.66% in case of setting the CO2 emission trade at zero. This is the level on which the project is barely profitable by soft loans raised by Japan Bank for International Cooperation (JBIC), etc. (NEDO)

Fiscal 1999 report on result of the model project for systematization of high-efficiency combustion of by-product gas in ironworks. Part 1/2; 1999 nendo seitetsusho fukusei gas koritsu nensho system ka model jigyo. 1/2

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-09-01

For the purpose of curtailing energy consumption of the steel industry, a large energy consuming industry in China, a model project was carried out for high-efficiency combustion system for by-product gasses in ironworks, with the fiscal 1999 results reported. This project is such that, in the reheating furnaces consuming as fuels various combustible gasses produced in iron and steel making processes, systems to permit control of mixed-gas calorie and oxygen content in a reheating furnace are incorporated, with demonstration and dissemination performed for technologies on improving energy consumption efficiency. This year, site survey was conducted to obtain information needed for the basic design for the model project. The heat balance of the objective reheating furnaces revealed that the fuel consumption could be reduced by 6 to 35% by implementing the model project. Investigations were made also on the obstructive impurities contained in the by-product gasses and on the gas purification equipment, etc., which elucidated that the impurity content was about the same as that of the major ironworks in Korea and Taiwan and that there would be no problem if proper inspection and maintenance were carried out. As for the equipment and devices, the majority with software was manufactured and transported to Chingdao, China. Further, Chinese engineers were invited to Japan for technical training. (NEDO)

FY 2000 report on the promotion projects by Research Institute of Innovative Technology for the Earth. Study on possibility of research exchanges; 2000 nendo chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo seika hokokusho. Kenkyu koryu kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the results of the study on possibility of research exchanges, conducted by Research Institute of Innovative Technology for the Earth (RITE) in FY 2000. For development of thin-film catalysts, HTE, a venture developing combinatorial chemistry application to catalysts, is a potential partner for the exchanges. One of the technical problems involved in underground sequestration of CO2 relates to evaluation of the reactions between CO2 injected under pressure and the surrounding rocks. It is a less site-specific theme, and preferably pursued through international networks. The RITE delegates have visited the British Geological Survey, Canada's Alberta Research Council, and US's Pennsylvania State University, Rice University and Chevron Petroleum, finding research exchange possibilities in all of these organizations for broad technical themes related to underground sequestration of CO2. For energy conversion technologies using biomass resources as the source materials, the potential partners for the research exchanges include Swedish Royal Institute of Technology, Belgium's Catholic University of Louvain and Spain's University of Zaragona which leads researches in production of gases from wastes and biomass. (NEDO)

Fiscal 1996 survey report. Data collection and evaluation analysis in the project on field tests on the fuel cell generation; 1996 nendo kenkyu hokokusho. Nenryo denchi hatsuden field test jigyo ni okeru data shuyaku oyobi hyoka kaiseki

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The paper installed fuel cell power generation equipment experimentally at various facilities which are the final diffusion form of the new energy power generation, conducted long-term operation under the actual load, collected/analyzed various data, arranged them as data useful for full scale introduction/diffusion, aiming at forming the base for general diffusion of the fuel cell power generation. The number of the systems installed for field test execution has been 24 places/28 units since the start of the project, and the system capacity totaled 4,250kW. The actual operation hours in five years are 6,000-28,000. In fiscal 1996, the average cumulative accumulated operational rate was approximately 68%, a little over that in fiscal 1995, 65%. The average load factor was 69% in fiscal 1995 and 70% in fiscal 1996. The utilization rate increased as a whole to about 57% on average if seeing only fiscal 1996, as compared with that in fiscal 1995, about 48%. The power generating efficiency was approximately 34% on average. As to the status of shutdown of the fuel cell power generation, the paper surveyed the average interval of failure, the rate of frequency of shutdown, the analysis of shutdown, etc. 250 figs., 29 tabs.

Research report for fiscal 1998. Research into the feasibility of exchange of studies for the development and promotion of global environment-related industrial technologies; 1998 nendo chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo. Kenkyu koryu kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The above was conducted by Research Institute of Innovative Technology for the Earth (RITE). Worldwide collaboration is mandatory for the settlement of environmental problems for the earth, and RITE is positively promoting its interaction with research institutes abroad. In fiscal 1998, it sent research teams to government organizations and research institutes in Europe and America for studies there. A study in Europe involved the preparation of chemicals from CO2 by virtue of novel biotic reactions, and RITE's microbial molecular function laboratory plans to start a leading study in fiscal 1999. In relation with environmental impact reducing technologies using sunlight-aided photocatalysts, visits were paid to three research institutes in America. RITE itself has developed a powdered semiconductor catalyst and is engaged in the study of producing hydrogen by decomposition of water using solar energy. Concerning the production of saccharides out of farm wastes remaining unused, researches were made into the feasibility of joint studies with some advanced research institutes in America. Discussions were made about the performance- and stability-related improvement of enzymes usable for the decomposition of biomass, the analysis of biological environmental circumstances that substance yielding microbes find themselves in under anaerobic conditions, etc. (NEDO)

Report on the database structuring project in fiscal 1996 related to the 'surveys on making databases for energy saving (2)'; 1996 nendo database kochiku jigyo hokokusho. Sho energy database system ka ni kansuru chosa 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

With an objective to support promotion of energy conservation in such countries as Japan, China, Indonesia, the Philippines, Thailand, Malaysia, Taiwan and Korea, primary information on energy conservation in each country was collected, and the database was structured. This paper summarizes the achievements in fiscal 1996. Based on the survey result on the database project having been progressed to date, and on various data having been collected, this fiscal year has discussed structuring the database for distribution and proliferation of the database. In the discussion, requirements for the functions to be possessed by the database, items of data to be recorded in the database, and processing of the recorded data were put into order referring to propositions on the database circumstances. Demonstrations for the database of a proliferation version were performed in the Philippines, Indonesia and China. Three hundred CDs for distribution in each country were prepared. Adjustments and confirmation on operation of the supplied computers were carried out, and the operation explaining meetings were held in China and the Philippines. (NEDO)

FY 2000 report on the project for research cooperation in the spread of the results of the analysis of effects of technology development; 2000 nendo kenkyu kyoryoku jigyo. Gijutsu kaihatsu koka bunseki seika fukyu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The Japan-China joint research and seminar were conducted which were titled 'The technological/economic approach for realization of a harmony of energy/environment/economy in China in a period of transition of the system and the study of the spread of the results.' In the study of the policy for development of small/medium enterprises in China, discussions were made on the stage of the development of small/medium enterprises in China, consideration of the credit guarantee system for small/medium enterprises, and the present situation of the credit evaluation of small/medium enterprises. In the study of the economy rule/regulation system of China, problems in the legal system that China are faced with by joining WTO and the measures to be taken therefor, study of the product quality law in China, study of the competition law system in China, and study of the environmental protection law. In the study of the control of enterprises in China, the environmental accounting in China. In the study of the measures to be taken to promote the inland region of China, the finance support system for great development of the west, and the study of the relation between the water source in the dry region of northwest China and the sustainable economic growth. Further discussed was the study of the intellectual property right system in China. (NEDO)

New energy vision for Nomura town. Fiscal 2000 survey report on regional new energy vision formulation project for Nomura town, Ehime Prefecture; Nomuracho shin energy vision. 2000 nendo Nomuracho chiiki shin energy vision sakutei nado jigyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-02-01

An effort is being exerted to build a town which will generate but a little environmental impact, with symbiosis with nature established as the highest priority target of the town administrative activities. Under the Nomura town new energy vision, a basic policy and measures are established toward the promotion of new energy introduction, with local features, existence of new energy resources, and the feasibility of new energy adoption taken into consideration. Surveys were made and the results are compiled into seven chapters, which involve (1) the trend of new energy, (2) local features, (3) existing amount and available amount of new energy, (4) basic policy toward the introduction of new energy, (5) main projects for the introduction of new energy, (6) details of the basic policy toward the introduction of new energy, and (7) the Nomura Town Deliberation Committee on New Energy Vision Formulation. Chapter (6) covers the assessment of new energy introduction feasibility, promotion of concretized introduction projects, public relations/enlightening/popularizing activities, and assistance for new energy introduction. Studied for introduction are photovoltaic power generation, solar heat utilization, wind power generation, biomass power generation, and the like. (NEDO)

Fiscal 1999 technical survey report. Model project implementation feasibility study in India on effective utilization of blast furnace gas pressure energy; 1999 nendo Indo ni okeru koro gas atsuryoku energy yuko riyo model jigyo jisshi kanosei chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

From the viewpoint of energy utilization stated above, blast furnace top pressure recovery turbine (TRT) unit installability was studied at Bhilai Steel Works of Steel Authority of India, Ltd., Bokaro Steel Works of Steel Authority of India, Ltd., and Visakhapatnum Steel Works of Rashtriya Ispat Nigem. The energy consumption rate at an Indian steelmaking plant is 8Gcal/t-steel, which is larger than 5-6Gcal/t-steel of Japan and therefore needs improvement. Out of the blast furnaces in India, 26 are larger than 1,000m{sup 3}, and two of them are provided with a TRT device of now-defunct Soviet Union manufacture. The blast furnaces were examined for pressure at the top, amount of gas at the top, amount of dust, and safeness in operation. The No. 2 blast furnace of the Borkaro plant was selected for the project, and studies were made for a wet type TRT device. Improvements to be achieved by TRT device installation were calculated to be a TRT output of 5,900kW, power output of 49,100MWh/year, saved crude oil amount of 12,990toe/year, and CO2 reduction of 40,200 tons-CO2/year. (NEDO)

FY 2000 report on the project for research cooperation in the spread of the results of the analysis of effects of technology development; 2000 nendo kenkyu kyoryoku jigyo. Gijutsu kaihatsu koka bunseki seika fukyu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The Japan-China joint research and seminar were conducted which were titled 'The technological/economic approach for realization of a harmony of energy/environment/economy in China in a period of transition of the system and the study of the spread of the results.' In the study of the policy for development of small/medium enterprises in China, discussions were made on the stage of the development of small/medium enterprises in China, consideration of the credit guarantee system for small/medium enterprises, and the present situation of the credit evaluation of small/medium enterprises. In the study of the economy rule/regulation system of China, problems in the legal system that China are faced with by joining WTO and the measures to be taken therefor, study of the product quality law in China, study of the competition law system in China, and study of the environmental protection law. In the study of the control of enterprises in China, the environmental accounting in China. In the study of the measures to be taken to promote the inland region of China, the finance support system for great development of the west, and the study of the relation between the water source in the dry region of northwest China and the sustainable economic growth. Further discussed was the study of the intellectual property right system in China. (NEDO)

Report on the wind power development field test project in the off-shore park in Daitocho Town in fiscal 1997. System design; 1997 nendo Daitocho kaiyo koen nado ni okeru furyoku kaihatsu field test jigyo hokokusho. System sekkei

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-01

This paper reports the wind power development field test project in the off-shore park in Daitocho Town in Shizuoka Prefecture. The annual average wind velocity was 4.2 m/s (at height of 20 m above the ground), where the facility utilization rates for 300 and 500 kW class plants were 15.1 and 16.7%, respectively. Both of the annual average wind velocity and the facility utilization rate do not meet the criteria established by NEDO. Although the location is adjacent to the Natural Park, there is no restricting condition for installation. The substation to which system linkage is to be performed is the Daito substation 3 km north of the planned location. The major load is the Daito Spa in the park facility. Ground bed at depth of 5 m will be used as the windmill foundation supporting bed. There is little electromagnetic wave hazard. The location is 380 m away from the nearest residential house, presenting no windmill noise problem. The amount of power to be generated was assumed 281,000 kWh. Specifications for nine models of 300-kW class windmills that can be introduced into Japan were discussed to select a model. The project cost was calculated to be 128.5 million yen. The construction cost will be 428,000 yen and the power generation cost 38.1 yen/kWh. Its economy is poor when the current unit price for surplus power purchase is considered, but the effect of enlightenment may be expected. (NEDO)

Survey report for fiscal 1999. Evaluation and analysis on items applied for in high-performance industrial furnace introduction field test project in fiscal 1999; 1999 nendo koseino kogyoro donyu field test jigyo chosa hokokusho. Obo anken hyoka bunseki

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper describes comprehensive evaluation and analysis mainly on the 51 items adopted in the high-performance industrial furnace introduction field tests. The development of a high-performance industrial furnace has completed the fundamental development research in fiscal 1998, and the possibility was verified on energy saving of more than 30% and reduction of NOx emission by 50% over that by conventional furnaces. Upon this fundamental achievement, the field test project has started as the comprehensive approach to developing the practically usable technologies for three years from fiscal 1998 until fiscal 2000, which is being promoted as a joint research project. According to the survey on the actual state in fiscal 1998, a little less than 20,000 industrial furnaces having combustion capacity of more than 500,000 Kcal/hr (excepting boilers) are being used. If these furnaces are converted into the high-performance industrial furnace, energy conservation of 210,000 x 10{sup 6} Mcal (converted to crude oil of 22.7 x 10{sup 6} kl/year) can be achieved from the maximum annual energy consumption of 700,000 x 10{sup 6} Mcal (converted to crude oil of 75.7 x 10{sup 6} kl/year). This conservation amount corresponds to about 12% of the final energy consumption in the whole Japanese industrial departments in fiscal 1996. It is expected that the performance of the full-size high-performance industrial furnace will be verified, and this technology will be promoted for wide proliferation. (NEDO)

FY 2000 Project of developing international standards for supporting new industries. Comprehensive study for promotion of the international standardization; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kokusai hyojunka suishin ni kakawaru hokatsuteki chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This project studies the schemes for the international standardization, trends of the international standardization by the international standardization organizations and related organizations, and activities for the international standardization by the enterprises in the advanced countries, among others, in order to promote the international standardization for the 8 research and development themes. These themes are SMIL (synchronized multimedia integration language) tag standard of the three-dimensional image data, based on MXL; systems for detecting gene recombination products; methods for testing mileage of gas-fueled automobiles; measurement of multi-colors; testing/evaluation methods for highly coherent lasers; methods of evaluating optical performance of microlenses for optical information processing; recycled CFRPs; and devices for measuring marine environments. The study results indicate that progress of the development of the international standardization of the advanced technologies can be followed by investigating the characteristics of the ISO publications; ISO is studying the business plans being developed by each TC, in order to improve market adaptability of the international standards; and the European countries add conditions for standardization when the research and development themes are contracted. (NEDO)

FY 2000 report on the results of the regional consortium R and D project - Regional consortium field. First year report. R and D of highly integrated micro-protein reactor array system; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium bun'ya. Koshusekigata micro protein reactor array system no kenkyu kaihatsu (dai 1 nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

By micro-processing, micro-protein reactor array is fabricated, and inside it a very trace of gene is amplified by PCR (polymerase chain reaction) and then was amplified by adding the transcription/translation reaction mixture to it. By causing the protein synthesis reaction using the amplified gene, a highly integrated protein library is constructed. For it, the development of a new micro-protein reactor array system ({mu} PRAS) was proceeded with. Studies were made in the following 8 fields: 1) materials of micro reactor array and the manufacturing method; 2) development of the element unit of {mu} PRAS; 3) trial manufacture of micro reactor array chip and the evaluation; 4) trial manufacture of the micro-domain high-speed DNA manipulation system; 5) method to control non-specific DNA amplification in unimolecular PCR; 6) basic study of technology of molecular evolution of degrading enzymes of degradation-resistant substances such as dioxin; 7) method to construct the enzyme lipase library and computer simulation; 8) optimization of a system to synthesize optical activity useful compounds using enzyme lipase. (NEDO)

Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium energy field / research and development of a reverse engineering system for local industrial articles (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium bun`ya / chiiki kogeihin muke reverse engineering system no kenkyu kaihatsu (daiichi nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper described the fiscal 1997 result of the research on the application of local industrial article use reverse engineering (RE, it had been regarded as imitation and reproduction technology, but has recently been as a part of the production information integration). With the actual local industrial article as standard, which has features in design and was added with local traditionality, such as glass having 3D free-form surface, 3D shape information modeling technology RE is developed, and a system for direct automatic metal mold processing is established, aiming at shortening of delivery date, cost reduction and higher grade. The target of the research is Okinawa prefecture. In fiscal 1997, study was made of the speeding-up of the non-contact 3D shape information inputting (multi-point simultaneous inputting by CCD of the laser reflected light of the actual model) and the data storage technology. Cast iron was selected as molding materials, judging from reactivity/machinability with heat resistant glass. Also studied was the blend of glass materials suitable for press forming. Further, studies were proceeded with of development of intellectual cutting tools into which sensor function is integrated and of virtual reality for facilitating/accelerating the design up to metal mold manufacturing. 39 refs., 88 figs., 21 tabs.

Report on the survey of the project on the environmentally friendly type energy community field test. Separate volume - reference data. Investigative project for development and commercialization of recycle technology of waste edible oil; 2001 nendo kankyo chowa gata energy community field test jigyo chosa hokokusho. Hai shokuryo yu no recycle gijutsu kaihatsu to jitsuyoka no tameno chosa jigyo (Bessatsu - Sanko shiryo)

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-06-01

For the purpose of promoting the effective utilization of biomass resource, an investigative study was made on the development of recycle technology of waste edible oil. In the survey, the following were carried out and the results were summarized: promotion measures for biodiesel oil by the EU, promotion measures for biodiesel oil by other countries including Canada, promotion measures for biodiesel oil by the US's Department of Energy (DOC), actual results of the use of biodiesel oil in Kyoto City, reference data on biodiesel oil in Japan, and tackling toward the promotion of BDF in the Ministry of Agriculture, Forestry and Fisheries. As to the transportation use fuel in the EU in the coming 20 years, biofuel, natural gas and hydrogen seem to be selected. If measures are positively taken, biofuel is expected to be 2%, 6%, 7% and 8% in FY 2005, FY 2010, FY 2015 and FY 2020, respectively. Also, natural gas is expected to be 2% in FY 2010, 5% in FY 2015 and 10% in FY 2020, and hydrogen is expected to be 2% in FY 2015 and 5% in FY 2020. (NEDO)

FY 1996 report on the basic survey project on the enhancement of energy efficiency in developing countries - database construction project. Volume 1. Outline of the survey and collection of the data to be included in database; 1996 nendo hatten tojokoku energy koritsuka kiso chosa jigyo (database kochiku jigyo) hokokusho. 1. Chosa no gaiyo oyobi database ni shurokusuru data no shushu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Following the previous fiscal year, construction/study of database were carried out with the aim of energy conservation for 8 countries: Japan, China, Indonesia, the Philippines, Thailand, Malaysia, Taiwan and Korea. In the study of the items of the data included, the 192 data extracted in conceptual design were re-classified into 6 large-groups and 91 medium-groups. As to the data collection, in A group countries, counterparts were requested to collect data, and 1342-1740 data were newly collected. In B group countries, Mitsubishi Research Institute, Inc. mostly collected 957 new data in Thailand, 814 data in Malaysia and 1312 data in Japan in cooperation with research institutes and investigating organizations in each country. In C group countries, 169 and 317 common data items were collected in Vietnam and India, respectively. Relating to plans for database promotion, as a result of the study with each country, 16 measures for promotion were extracted in terms of the leveling-up of NEDO-DB recognition, education of the use method, training of the operation method, etc. (NEDO)

Fiscal 1998 intellectual infrastructure project utilizing civil sector functions. Research and development project on prompt-effect type intellectual infrastructure creation (Buildup of base for thermophysical property data for new industry creation); 1998 nendo minkan no kino wo katsuyoshita chiteki kiban jigyo seika hokokusho. Sokkogata chiteki kiban sosei kenkyu kaihatsu jigyo (shinki sangyo sosei no tame no netsubussei data ni kansuru kiban seibi)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For promoting the creation of new industries, thermophysical data on high-temperature molten bodies, liquid substances, solid materials, and the like were collected, and further measurements were performed; the data were stored in distributed databases; and databases were also developed about access to the Internet. In the study of the thermal properties of high-temperature molten bodies, data were collected from technical literature concerning molten silicon for semiconductor production, that is, 2 about thermal diffusivity, 4 about viscosity index, 30 about surface tension, 8 about density, and 6 about emissivity; and, concerning potassium niobate, 6 about density, 4 about surface tension, and 5 about viscosity index were collected. Thermal properties were measured for molten silicon and molten carbonates. In the study of thermal properties of fluids, data such as PVT (pressure, volume, temperature) values, boiling point pressure, saturated liquid density, isothermal compressibility, cubical expansion coefficient, surplus mol volume, and the like were collected again from technical literature concerning trifluoroethanol and its water solution. Thermodynamic properties of the aqueous ammonia solution comprised of equimolecules were measured. (NEDO)

Report on the survey of the project on the environmentally friendly type energy community field test. Separate volume - reference data. Investigative project for development and commercialization of recycle technology of waste edible oil; 2001 nendo kankyo chowa gata energy community field test jigyo chosa hokokusho. Hai shokuryo yu no recycle gijutsu kaihatsu to jitsuyoka no tameno chosa jigyo (Bessatsu - Sanko shiryo)

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-06-01

For the purpose of promoting the effective utilization of biomass resource, an investigative study was made on the development of recycle technology of waste edible oil. In the survey, the following were carried out and the results were summarized: promotion measures for biodiesel oil by the EU, promotion measures for biodiesel oil by other countries including Canada, promotion measures for biodiesel oil by the US's Department of Energy (DOC), actual results of the use of biodiesel oil in Kyoto City, reference data on biodiesel oil in Japan, and tackling toward the promotion of BDF in the Ministry of Agriculture, Forestry and Fisheries. As to the transportation use fuel in the EU in the coming 20 years, biofuel, natural gas and hydrogen seem to be selected. If measures are positively taken, biofuel is expected to be 2%, 6%, 7% and 8% in FY 2005, FY 2010, FY 2015 and FY 2020, respectively. Also, natural gas is expected to be 2% in FY 2010, 5% in FY 2015 and 10% in FY 2020, and hydrogen is expected to be 2% in FY 2015 and 5% in FY 2020. (NEDO)

17th Business Report Meeting of New Energy Industrial Technology Development Organization (NEDO). Section Meeting on International Cooperation Projects; Dai 17 kai jigyo hokokukai. Kokusai kyoryoku jigyo bunkakai

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-09-01

In this section meeting, reports were made on the following themes: 1) pregrinder model project; 2) power recovery model project; 3) energy conservation model project and the importance of the spread. In 1), this model project aims to demonstrate that the electric power unit requirement for cement production can be reduced by installing a pregrinder at the front step of ball mill as the finish process at a cement factory in Indonesia, increasing capacity of ball mill grinding, and reducing operational loads of the ball mill which is large in power consumption. In 2), this project aims to supply China a technology to recover power from high temperature/high pressure exhaust gas via gas expander as electric power of 5.8MW after separating FCC catalyst associated with from the exhaust gas from the generative tower of fluid catalytic cracking equipment for oil refining. To come up to expectations for Japan from neighboring countries in Asia, NEDO Information Center carried out the energy conservation model project, etc. as the international cooperation related project in the energy/environment field. The center is now developing 10 projects. (NEDO)

FY 1999 report on the results of 'the model project for effective utilization of the waste heat discharged from the combustion of paper-manufacturing sludge'; 1999 nendo seika hokoku. Seishi surajji nensho hainetsu yuko riyo moderu jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of reducing the consumption of fossil fuel and reducing emissions of global warming gases in Malaysia, a model project for thermally effective use of the sludge discharged from paper-manufacturing plant was carried out. Concretely, the paper-manufacturing sludge discharged from paper-manufacturing plant is to be dewatered and improved of its lower heating value. Then, the sludge is to be burned in fluidized bed incinerator, and the steam is to be generated by recovering heat using waste heat recovering boiler. The steam obtained is to be used as process steam of the plant. In this fiscal year, the first year of the project, the attachment to the agreement was prepared in terms of the allotment of the project work between Japan and Malaysia, various kinds of gist, schedules, etc. and signed. After that, the determination of the basic specifications for facilities was made according to the attachment to the agreement. Now, the basic design of the whole plant is being made. The design of the process flow sheet, design of the layout plan for plant equipment, etc. were finished. The goods to be purchased are now being estimated and assessed. Moreover, as to the civil engineering/construction design, drawings of the basic design are now being made. (NEDO)

Fiscal 1997 research report on the data collection, evaluation and analysis in the PV power generation field test project for public facilities; 1997 nendo kokyo shisetsu nado yo taiyoko hatsuden field test jigyo ni okeru shushu data hyoka kaiseki

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

As a part of the field test project for diffusing PV power generation into public facilities generally, evaluation and analysis were made on the collected data from 105 sites installed during fiscal 1993-1996. Analysis of operation characteristics was made by using parameters obtained by developing a basic equation for every component. 94% of all the sites fell under the total solar irradiation of 3.0- 4.5kWh/m{sup 2}/D. 83% of those fell under the equivalent array operation time of 2.5-4.0h/D. 70% of those fell under the equivalent system operation time of 2.5-3.5h/D. 72% of those fell under the system operation time of 9.0-12.0h/D. 78% of those fell under the effective inverter efficiency of 0.84- 0.96. 68% of those fell under the inverter load factor of 0.25-0.35. 85% of those fell under the array performance ratio of 0.7-1.0. 83% of those fell under the system performance ratio of 0.6-0.9. The generation cost decreased from 270yen/kWh in 1993 to 100yen/kWh in 1996 because reduction of an installation cost largely contributed to reduction of the total cost. (NEDO)

Project in fiscal 2000 of developing international standards for supporting new industries. Standardization of evaluation method for gene inspection system; 2000 nendo shinki sangyo shiengata kokusai hyojunka kaihatsu jigyo seika hokokusho. Idenshi kensa system no hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Discussions and deliberations were given by the comprehensive survey committee on standardization of a total gene inspection system from specimen adjustment necessary for the gene inspection system to data processing. This paper summarizes the achievements in fiscal 2000. In standardization related to the specimen procedure and the inspection technique, the specimen storing method and the report statement contents were established. In addition, verification was made on the heat-resistant enzyme reagent and such measuring devices as the electric migration device and the photographing device. Discussions were given on standard substances used in the gene inspection. Regarding the K562 cell strain, cross-checking was performed in three institutions, wherein discussions were given on interchangeability of the inspection results, and the usefulness of the K562 cell as a standard substance. As a result, all the three institutions have come to an agreement on the Southern method, the FISH method and the RT-PCR method, but not on the real-time PT-PCR method, leaving the subject as the future assignment. In the survey for Europe and America, visits were made to AFNOR, CEN, DIN, FDA and CAP for the attempt of collecting information and establishing international exchange. (NEDO)

R and D project for large industrial technologies in fiscal 1989. Report on achievements in R and D of robots for critical works; 1989 nendo seika hokokusho. Ogata kogyo gijutsu kenkyu kaihatsu jigyo. Kyokugen sagyo robot no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-03-01

Research and development have been performed on basic technologies common to different types of robots to carry out works in critical conditions. This paper summarizes the achievements in fiscal 1989. In the R and D of sensor technologies, a prototype tri-axial one-millimeter sensor array and a signal processing device were produced and evaluations were given. A prototype production and evaluations were made on a system that can recognize comprehensively the slip, hardness, and moment as the tri-axial tactile information. In the R and D of motive force technologies, discussions were given on improvement of sensitivity of the torque sensor in the actuator for force control. Design and prototype fabrication were carried out on a speed reducer integrated actuator having a torque sensor for the manipulator's elbow joint. In addition, a force controlled controller was fabricated on a trial basis, which compensates the non-linearity of the force controlled actuator by means of software control. In the R and D of the robot languages, an application program was prepared on a representative work related to movements of a critical work robot. Verification was also conducted on the reasonability of the grammar specifications. (NEDO)

Fiscal 1999 technical survey report. Model project implementation feasibility study in Malaysia on effective utilization of waste heat from paper sludge incineration; 1999 nendo Malaysia ni okeru seishi sludge nensho hainetsu yuko riyo model jigyo jisshi kanosei chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Efforts are under way to popularize practical energy conservation technologies through verification on real machines in target countries. Possibilities were studied that Malaysian paper making plants would adopt technologies of collecting heat from high-temperature exhaust gas from paper sludge incineration and of effectively utilizing the thus-collected heat. The Malaysian paper making industry produced 800-thousand tons or more in 1998, covering 72% of the total national demand. Heat recovery facilities may be installed in 15 plants. On-site surveys were made into their actual states, and then Genting Sanyen Industrial Paper Sdn. Bhd. was selected as the plant for the model project, and detailed model project feasibility studies were conducted. The studies covered the amount of wastes from paper making, their properties, treatment process, amounts of utilities to be used during system operation, land on which to build the facilities, and a plan for collecting invested funds. As the result, it was concluded in view of the magnitude of the expected fruit that the model project be implemented at this plant. (NEDO)

Fiscal 2001 survey report on regional new energy vision formulation at Kyonan Town; 2001 nendo Kyonan machi shin energy vision sakutei chosa hokokusho. Chiiki shin energy vision sakutei tou jigyo (Watashitachi ga tsukuru machi, subete ga koen no machi)

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

A regional new energy vision was formulated at Kyonan Town, Chiba Prefecture, which includes a new energy introduction plan, an action program for the plan, and the like, intended to promote enlightenment/popularization relative to new energy and environmental matters. Kyonan Town consumes 18.69 times 10{sup 10} kcal of energy, with oil accounting for 65.4%, LPG for 6.0%, and electricity 28.6%, the statistics disclosing that the town has an oil-dependent energy consumption structure. The new energy likely to be introduced will comprise 13,574 times 10{sup 10} kcal/year in solar energy, 336,187 MWh/year in wind power, 17,170 kWh/year in small-scale hydroelectric power, 0.57 times 10{sup 10} kcal/year in refuse fueled power, and 0.60 times 10{sup 10} kcal/year in biomass fueled power. The town's new energy introduction project centers on photovoltaics, passive solar heat utilization, wind power, small-scale hydroelectric power, and aims to introduce the new energies into public facilities such as the Eco Garden and Katsuyama Primary School, and into kindergartens, nursery schools, shopping malls, and so forth. A plan was also worked out for adopting clean-energy vehicles for official use. (NEDO)

Report on the research cooperation promoting project in fiscal 1998. Research cooperation related to the mine waste water treatment technology utilizing biomass; 1998 nendo kenkyu kyoryoku suishin jigyo hokokusho. Bio riyo ni yoru kohaisui shori gijutsu ni kansuru kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This paper describes the achievement in relation with the mine waste water treatment technology utilizing biomass, from among the promotion projects for research cooperation with China. Waste water is converted into ferric iron (Fe{sup 3+}), which precipitates at low pH, by utilizing iron oxidizing bacteria which use ferrous iron (Fe{sup 2+}) in the waste water as the energy source, and is precipitated and removed by using low-cost calcium carbonate as a neutralizing agent. Fiscal 1998 has performed eight site surveys with 47 persons in total. The main survey items are the study and guidance of pilot plant operation and the survey on measures to prevent occurrence of contamination by heavy metals in Wushan Mine. Additional site surveys were made at Dexing Mine and Yinshan Lead/Zinc Mine. Continued from fiscal 1997, consumables required for the pilot plant were purchased, and items of the bench-scale testing equipment used by Japan for domestic researches (an oxidation and neutralization testing equipment and a copper recovering and testing equipment) were transported to China. The operation research data of the pilot plant were put in order and analyzed. This paper summarizes the concept design of the shaft waste water treatment facilities for the north mine in Wushan Mine, and the surveys on measures for heavy metal contamination sources. (NEDO)

Museum of water, green and the sun - Marumori. New energy vision of the Marumori Town area; 2001 nendo Marumori machi shin energy vision hokokusho. Chiiki shin energy vision sakutei tou jigyo (Mizu to midori nto taiyo no hakubutsukan Marumori)

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

In Marumori Town, Miyagi Prefecture, a 'new energy vision of the area' was worked out which indicated the assessment of the energy reserved in the town and the course of new energy to be determined in the future. The energy consumption amount of Marumori Town in FY 1999 was estimated at 47,535 kL in crude oil conversion. By sector, the energy consumption amount was the largest in the order of the industrial sector, the transportation sector and the commercial/residential sector. The availability of new energy in Maruyama Town was estimated at approximately 480,585 GJ, of which the solar energy utilization was the largest, 53.1%. The photovoltaic power generation was the next largest, 25.4%, followed by the temperature difference energy (underground water), 8.9%, clean energy car, 7.8%, etc. As a plan for the first introduction of new energy, the following were studied: introduction of photovoltaic power generation facilities to the Marumori Town Office, introduction of new energy to public facilities around the Fudoson Park, introduction of wind power generation facilities to the town-run pasture, construction of the Marumori-type biogas plant, construction of a mini hydroelectric power plant, introduction of clean energy car to public vehicles, introduction of new energy facilities to the area of Kawa-no-Eki (station of the river), etc. (NEDO)

FY 2000 research cooperation project on the research cooperation for the preservation, sustainable utilization, etc. of the biological diversification. Follow-up; 2000 nendo kenkyu kyoryoku jigyo. Seibutsu tayosei hozen to zizokuteki riyo to ni kansuru kenkyu kyoryoku (Follow up)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of contributing to developing countries' preserving biological resources in the tropical region, etc. and making the sustainable utilization of biological resources using biotechnology, etc. possible, research cooperation for strengthening the base of international research cooperation was given, and the FY 2000 results were outlined. In this fiscal year, visits were paid to research institutes in Indonesia, Thailand and Malaysia for survey of the present situation. In Indonesia, conducted were the study of information system and culture collection, study of plant utilization technology, study of utilization technology of bacteria, etc., and improvement in personnel, facilities and maintenance management power of research cooperation institutes was confirmed. In Thailand and Malaysia, conducted were the study of information system and culture collection, study of rule making of the access profit distribution to genetic resource, and management of the biological resource sampled and study of the route to the industrial utilization. Taking advantage of this project, the contract for the genetic resource search for commercial purpose was agreed between a Japanese company and a Malaysian institute. (NEDO)

FY 2000 research cooperation project on the research cooperation for the development of an advanced multimedia information system. Results of the research; 2000 nendo kenkyu kyoryoku jigyo. Senshinteki multimedia joho system no kaihatsu ni kansuru kenkyu kyoryoku (Kenkyu seika)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of developing an information system that has the hi-tech technology useful for China and high diffusion, joint research was conducted on the development of the model system and the demonstrative test, and the FY 2000 results were summed up. As to the synthetic materials flow information system, FIT/GAP analysis was made for improvement of the materials flow system and research development of additional functions. Relating to the education/culture/information system, made were the structural design of the remote education realtime system, development of the control use program, etc. Concerning the agricultural information system, it finished the stage of the investigational analysis/basic design and reached the stage of the detailed design/manufacture/initial experiment. About the forest fire-prevention information system, conducted were the design of the work application/technical support for the development in the department of forestry. As to the medical information system, image database and software of high speed image processing were developed. In relation to the environmental monitoring/flood monitoring information system, application software was developed for the forecast of disaster, assessment of disaster, relief decision-making support, etc. (NEDO)

FY 2000 Project of developing international standards for supporting new industries. Standardization of the fine bioceramics testing/evaluation methods; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Seitaiyo fine ceramics no shiken hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the FY 2000 results of the research and development of the fatigue characteristics of the bioceramics, fatigue and impact-resistance characteristics of the members of these materials, and methods of evaluating their compatibility with a living body, for proposing the international standards. The test results of alumina and zirconia as the bioceramics indicate that their bending fatigue characteristics greatly depend on environmental conditions and frequency, suggesting necessity for the evaluation in the environments which simulate the living body inside. The compression and impact tests are conducted for the artificial femoral heads with a taper. It is found that the simulated body fluid, having the dissociated ion concentration adjusted at the level in the human blood plasma, remains unchanged in the concentration at 36.5 degrees C for 4 weeks; the ion concentration is unaffected by filtration with the aid of the microfilter useful for, e.g., removal of bacteria; and the synthetic apatite has almost the same composition as that for the bones in a living body. It is also suggested that activity of the bioactive ceramics can be evaluated by their ability for forming apatite in the simulated body fluid. (NEDO)

Research cooperation project in fiscal 2001. Research cooperation on putting into practical use of district complying type photovoltaic power generation system; 2001 nendo kenkyu kyoryoku jigyo. Chiiki tekigo gata taiyoko hatsuden system tou no jitsuyoka ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

Research cooperation has been performed with an intention of establishing technologies to develop a design program for photovoltaic power generation systems suitable for the diverse natural and social conditions in China, the performance inspections and quality enhancement thereon. This paper summarizes the achievements in fiscal 2001. For installing the photovoltaic power generation system, procurement, transportation and installation were carried out in Gansu Province for a 8.4 kW integrated system and in Qinghai Province for 10 kW and 12 kW integrated systems. Visits were made to the sites to confirm the operating conditions, and maintenance and management conditions of the systems having been installed to date. With regard to performance evaluation devices of the cells and modules, some pieces of the equipment were repaired and re-adjusted, and training for using them was executed. Eight persons have visited Japan from China and participated in the training in Japan for utilization and operation of the photovoltaic power generation systems for the persons involved in the system operation. In addition, in order to determine the future information exchange directions, workshops were held with PV experts and manufacturers participating from Japan to exchange items of information. (NEDO)

FY 2000 report on the results of the model project on facilities for the effective utilization of industrial waste from industrial complex. Separate Volume 3; 2000 nendo Kogyo danchi sangyo haikibutsu yuko riyo setsubi model jigyo. Dai 3 Bunsatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

For the purpose of promoting the effective utilization of industrial waste as petroleum substitution energy resource and reducing the consumption of fossil fuels in Thailand, a model project on facilities for the effective utilization of industrial waste from industrial complex was worked on, and the FY 2000 results were reported. In Separate Volume 3, drawings of the following were included: furnace, free board spray nozzle, dispersion air nozzle, secondary burner, sand make-up conveyor, sand discharge gate, boiler, silencer for boiler safety valve, steam header, steam accumulator, gas cooling tower, refuse drainage storage tank, small sized drainage pump, pressure tank, flue gas duct, air damper, incombustible conveyor 2, sand circulation system bag filter, weighing bridge, fan starter panel, control panel, control panel, local switch box, distributed control system, field instrument, flue gas analyzer. (NEDO)

FY 1999 research cooperation project. Research cooperation in development of technology to extract/treat mineral resources in environmental harmony and high-efficiently; 1999 nendo kankyo chowagata kokoritsu kobutsu shigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This project is aimed at effectively using non-ferrous metal resource in Kazakhstan Republic and at conducting a joint development of the environment-friendly and efficient technology to extract/collect valuable metals (copper, gold, silver, rare metal, etc.) including in quantity in the slag generated with the mine operation in Kazakhstan. For the purpose of collecting valuable metals from slag, etc., the project is to develop the technology to collect valuable metals in saving energy and in low environmental loads by adopting the wet treatment process and to carry out the field survey on the existence of slag, etc. and the research on minerals. As the field research/domestic research, various element technologies are also to be carried out such as leaching, solvent extraction, electrolyte sampling, and waste water treatment. Based on the R and D of the element technology, a pilot plant is designed/fabricated and installed at the site in Kazakhstan. Then, the operation is studied and analyzed to make a technically/economically comprehensive evaluation. In this fiscal year, the field survey, research on the wet treatment, and test on the waste water treatment are conducted. Facilities of a pilot plant were transported to the site. (NEDO)

Fiscal 2000 survey report. Foundation building project for international energy use rationalization. Master plan preparation for rationalized energy use; 2000 nendo kokusai energy shiyo gorika kiso seibi jigyo chosa hokokusho. Goriteki energy shiyo no tame no master plan sakusei

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For energy conservation and environmental protection using technologies for effective consumption of energy and for preventing pollution due to energy consumption, master plans were studied and prepared on photovoltaic power generation, wind power generation, natural gas utilization, and so on, for the Xinjiang Uygur Zizhiqu, Gansu Province, and Guandong Province, respectively. Propositions addressing the Xinjiang Uygur Zizhiqu involved a decrease in dependence on coal, utilization of natural gas, introduction of coal-fired cogeneration systems, introduction of wind power up to the level equivalent to the supply reserve capability, energy conversion and new industry development using natural gas, promotion of electrification of local communities, and so on. Propositions addressing Gansu Province involved the hydroelectric power system as the core of power sources, decrease in dependence on coal, enhanced utilization of natural gas, energy conversion and new industry development utilizing natural gas, and so on. Propositions addressing Guangdong Province involved a decrease in dependence on coal and oil, enhanced utilization of natural gas, introduction of natural gas-fired combined cycle power generation into urban sectors, accelerated utilization of wind power generation on isolated islands, and so on. (NEDO)

R and D project for large industrial technologies in fiscal 1990. Report on achievements in R and D of robots for critical works; 1990 nendo seika hokokusho. Ogata kogyo gijutsu kenkyu kaihatsu jigyo. Kyokugen sagyo robot no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-01-01

Research and development have been performed on basic technologies common to different types of robots to carry out works in critical conditions. This paper summarizes the achievements in fiscal 1990. In the R and D of tactile sensors, a prototype multi-element sensor array applicable to fingers of a robot hand was produced, and the characteristics test was conducted. In the R and D of motive force technologies, a force controlled actuator for wrist containing a torque sensor was designed and produced on a trial basis, whereas evaluations were given on the size and weight reduction and the force control performance. Regarding the actuator with redundant degree of freedom, a force controlled arm was attached with an actuator with three degrees of freedom to have performed an evaluation experiment. With regard to a small size and light weight controller, fabrication was carried out on a multi-function, high-density controller which adds positional control and peripheral interface functions to the force controlling function, and an evaluation was given. In the R and D of robot language, discussions were given on robot languages related to each system of movement, manipulation, and sensors, and the grammar specifications were prepared. (NEDO)

Fiscal 2000 survey report on project for promoting international cooperation. Survey on coal utilization in APEC region (Coal note); 2000 nendo kokusai kyoryoku suishin jigyo chosa hokokusho. APEC iki nai ni okeru sekitan riyo jokyo tou chosa (Koru note)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the purpose of contributing to the infrastructure for promoting clean coal technology (CCT), there were compiled as the 'coal note' various kinds of coal-related information in China, Indonesia, Philippine, Thailand and Vietnam among APEC countries. Concerning China, for example, economic growth and energy supply/demand in the category of the energy outline were described in detail; as were the guiding principle. individual guidance plan, and specific energy policy of the 10th five year plan, in the category of the energy policy; coal deposits, geological summary, coal quality in each coal forming period, and the status quo of development, in the category of the coal mines and development; coal supply/demand, production, consumption, and export, in the category of the present status of the coal industry; producers, sales, quality of product coal, distribution, and price, in the category of the domestic supply; present state of environmental problems relating to coal, and environmental measures intended for coal, in the category of the coal-related environmental issues; and development, production, coal cleaning, quality control, safety control, and utilization (combustion, liquefaction and gasification), in the category of coal utilization technology, respectively. (NEDO)

Preliminary survey of `Green Recycling System`; Jigyo jizen chosa `green recycle system`

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This report describes the construction of `Green Recycling System` which aims to change deserts to lush lands and to stabilize food supply. A cross-linked polymer produced by irradiating the gooey threads of natto (fermented soybeans) with gamma rays can absorb and hold up to 5,000 times its own weight of water. This biodegradable polymer may be used to develop seed gels and pellets to grow soybean, rice and wheat to improve the productivity of deserts and to protect threatened lands from desertification. This technology will be of great value in establishing stable supply of food resources, especially for the Middle East where deserts are expanding as well as for Africa where serious food shortage is already in place. To undertake the Green Recycling System Project, it is indispensable to develop technologies for producing PGA polymer in large quantity, mass production process of bridged PGA through radiation, chemical cross-linkers, new technologies for growing plants using water retainers, water-retaining materials for arid areas, general systems for growing plants in arid areas, and environmentally benign industrial infrastructures. 76 refs., 59 figs., 29 tabs.

System specifications for the fiscal 1995 NEDO wind power development field test project. Fukayama area, Nagashima-aza, Hiraizumi-cho, Nishiiwai-gun, Iwate Prefecture; 1995 nendo NEDO furyoku kaihatsu field test jigyo system sekkeisho. Iwateken Nishiiwaigun Hiraizumicho Nagashima aza Fukayama chinai

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-07-01

This is system specifications for the wind power development field test project (NEDO). The system was designed setting the annual mean wind speed at 6m/s and the annual occurrence probability of wind speed of 4-6m/s at 12% or more. Considering the result of the high frequency power disturbance survey, the mountainside toward 70m west of the top of the Otowayama was planned for a site for the construction. Only one wind turbine is to be installed since the cost of land formation for the mountainside site becomes higher because of the distances between wind turbines required in the case of installing more than one wind turbine. The system interconnects with the Hiraizumi substation near by. The mean power generation amount per year by size of wind turbine was supposed to be 754, 1230, and 1467 MWh for 300, 500, and 600 kW classes, respectively. The budget raisable is 200 million yen, and operating expenses are 146, 203, and 228 million yen for each class mentioned above. The 500-600 kW class is high in economical efficiency and profitable now and in future. In the light of the license of chief electric engineer requested for the 600 kW class, selected was Mitsubishi Heavy Industries` MWT-500 Up-Wind type. Its specifications are: 3 GFRP blades, 32 rpm, 38m rotor diameter, 38m tower height, pitch control, and 490 kW. 49 figs., 53 tabs.

Fiscal 2000 project for development of international standards for supporting novel industries. Standardization for securement of interconnection between intelligent home electric appliances; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo. Johokadenkiki kan no sogo setsuzokusei kakuho no tameno hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development had been under way since fiscal 1998 for working out propositions relating to the international standardization of connection interface systems for digital AV (audio-visual) equipment. This report outlines the result of the project in its fiscal last year. The link working group (WG) actually built a transceiver at 5 mm pitch in its second trial, measured and evaluated its behavior under high-temperature and high-humidity circumstances, and acquired numerical data for interface specifications. The connection interface WG in its second trial fabricated a tiny optical connector for POF (plastic optical fiber) and evaluated its resistance to environment. As the result, sufficient resistance to environment was detected in the connector, and then a proposition was presented to IEC/TC86 that the connector be standardized as an optical connector for intelligent home electric appliances. The POF optimization WG performed an environment resistant test for POF, similar to those for transceivers and connectors, and then recognized that POF of the GI type was low in transmission loss and that it stably retained its wide-band feature. (NEDO)

FY 1999 report on the investigational study of the actual state of the utilization of clean energy vehicles for the transport business use; 1999 nendo chosa hokokusho. Unso jigyo yo clean energy jidosha no shiyo jittai ni kakawaru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of promoting the utilization of clean energy vehicles (CEV), survey was made on the assessment of the pollution by the CEVs introduced by now, subjects on the utilization, etc. As to the transport business use CEV running in the market, CNG vehicle is mostly used, and therefore, the gas emitted from them was tested. As a result, it was found out that CNG vehicle emits fewer NOx, PM and soot/smoke than diesel cars and contributes to improving the air pollution in large cities. However, it emits more CO2 than diesel car, and accordingly, it is necessary to reduce the fuel consumption. The practicality in the limited running distance is almost the same as that of diesel car, but it is desirable to improve startability, acceleration and gradability. Further, the occurrence of any troubles was pointed out in a third of the total numbers of CEV vehicle. Improvement in reliability is a must. CEV is higher in car cost than diesel car, and for the spread/promotion, it is necessary to prepare for assistance such as subsidy. Moreover, there are many requests for improvement in number, business hours, supply capacity, etc. of fuel supply station. (NEDO)

Fiscal 1994 survey of the base arrangement promotion for foreign coal import. Project to heighten the quality of subbituminous coal by low temperature carbonization process; 1994 nendo kaigaitan yunyu kiban seibi sokushin chosa. Teion kanryuho ni yoru arekiseitan no kohinshitsuka jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

The low-temperature carbonization process of coal is a technology to produce high grade reformed coal corresponding to bituminous coal and coal oil corresponding to heavy oil from subbituminous coal and supply them at prices close to the present market ones. From viewpoints of diversified sources and multiple export harbors, an initial-stage survey was conducted of the whole flow from new development of undeveloped mining areas in the northwest of Sumatra, Indonesia to bringing by ships to Japan of products reformed by LFC process of the US SGI`s low-temperature carbonization technology. Clean coal prepared after mining is produceable at a little higher than $12. At processing ability of 10,000 tons/day of raw coal, production is expected of approximately 5,700 tons/day of solid products of more than 6,500 kcal/kg and approximately 1,000 tons/day of low sulfur C heavy oil class oil. The finished cost of solid products is about $25/ton, which becomes about $40/ton at the harbor price in Japan. In conclusion, the project to enhance the quality of subbituminous coal by the low-temperature carbonization is promising as a total system. 10 refs., 54 figs., 30 tabs.

FY 1998 Report on field test project study for introduction of high-performance industrial furnaces. Detailed measurement study of FY 1998 joint research demonstration data; Koseino kogyoro donyu field test jigyo. 1998 nendo kyodo kenkyu jissho data no shosaina sokutei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Described herein are the FY 1998 results of measurement and study for introduction of the high-performance industrial furnaces. The NEDO's works for development of the high-performance industrial furnaces have been almost completed. The field tests are conducted to verify leveling and increasing temperature in the high-performance industrial furnaces. The data are collected in the existing and modified furnaces at the standard treating rate for each of the selected furnaces. The measured items are heat patterns of the works, temperature distributions within the furnace, heat balances in the combustion furnace, waste heat at the regenerative heat recovery unit, and exhaust gas components. The investigated items are names, materials, shapes, weights and quantities of the works; charging/discharging temperature; heating time; temperature in each furnace; consumption, types and heating values of the fuels used; air/fuel ratios; presence or absence of recuperator and its conditions when adopted; air temperature upstream and downstream of the heat accumulator, and exhaust gas temperature and components; temperature of the heat accumulator's external walls; cooling water rates, and inlet/outlet temperature, surface temperature of the furnaces' external walls; and furnace dimensions and structures. The measurements are done by thermocouples for various types of temperature, and O{sub 2}, CO2, CO, NOx meters and other analyzers for the components. The data are collected on a continuous basis. (NEDO)

Fiscal 2000 project for development of international standards for supporting novel industries. Standardization of production process system (Development of basic STEP standards); 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo. Seisan process system no hyojunka (STEP kiban kikaku no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are under way to develop STEP (standard for the exchange of product model data) of ISO-10303 into specifications for expressing the total life cycle of products from designing, manufacturing, to disposition. Japan's study centers about product model expression involving 'thing-making for machine products.' In the study, the functions of the mechanical production process system ranging from designing to manufacturing were analyzed, and the results were built into an integrated application activity model (I-AAM). The I-AAM was analyzed, and an assembly model capable of expressing detailed relations between parts, such as mechanical linking and binding, was developed, and the model was accepted as a new work item at TC184/SC4 in February 2001. In relation to the parametric assembly of Part 108, moreover, the fruit of this research and development effort was adopted. In relation to manufacturing, problems were extracted involving important production designs between the processes of designing and manufacturing. They were raised at SC4, and a data model was proposed. (NEDO)

FY 2000 Project of developing international standards for supporting new industries. Standardization of the testing/evaluation methods for high coherent lasers; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Ko coherent laser no shiken (hyoka hoho no hyojunka)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the FY 2000 results of the development of high-precision, stabilized lasers, laser interferometers and signal processors, and developmental researches on the testing/evaluation methods for spectral characteristics of high-performance lasers, among others, for proposing the international standards. The program for narrowing the spectral lines for semiconductor lasers experimentally confirms validity of the external resonator structure with the diffraction lattice. The program for the developmental research on spectral width meter designs the width meter based on the delayed self-heterodyne technique, because of necessity for measurement of the spectral line width at a resolution of several hundreds Hz or less. The program for the saturation spectroscopy of iodine molecule designs and fabricates the iodine cell, to lock the semiconductor laser wavelength on the specific absorption line of iodine. It is judged, based on the test results, to be rational to adopt the absorption line of the (6-3) transitional P33 superfine structure. The program for the developmental research on wavelength meter conducts the preliminary tests for atmospheric pressure, temperature and humidity changes as the parameters which affect the measurement accuracy. (NEDO)

Fiscal 2000 project for development of international standards for supporting novel industries. Standardization of methods for testing and evaluating plastic optical fiber; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Plastic hikari fiber no shiken hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Studies were made about methods for testing and evaluating plastic optical fiber (POF) for the purpose of submitting a proposition to IEC (International Electrotechnical Commission) for the methods to be internationally standardized. In this fiscal year, tests and analyses were conducted relative to the effects of the light source emission area size, wavelength, and axial displacement. Next, underfilled launch was studied from a practical viewpoint, and a method using a mode filter was proposed. Finally, round robin tests were conducted for each of the companies using overfilled launch and underfilled launch, and the reproducibility of measured values was grasped. In this fiscal year, a new study added, which involved a method for measuring structural parameters. Though POF was below standard as an object of IEC's gray scale method, yet it was found, thanks to the recently developed CCD (charge coupled device) cameras, that the method might also be applicable to POF. A groundwork plan was drafted on band test methods including the overfilled launch method toward international standardization. (NEDO)

Fiscal 1996 research cooperation promotion project. Report on the Japan/Mexico international cooperation research on recovery of valuable elements in brine; 1996 nendo kenkyu kyoryoku suishin jigyo. Kansuichu no yuka shigen kaishu gijutsu ni kansuru kenkyu kyoryoku follow up hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

In the research cooperation promotion projects having been carried out, the R and D of an overall recovery system have been conducted which recovers effectively and systematically valuable resources such as magnesium, bromine and boron including in brine made after the salt manufacturing in the coastal region in Mexico. In this project, as the research on the distilling process needed for commercialization of the system to recover valuable resources from the brine, Japan has been collecting information on various distilling processes and solar pond systems and studying a distilling process appropriate to the site jointly with Mexico. As a result, a seawater desalination process which combined the solar pond using solar energy and the evaporation method was recommended as a low-priced distilling method. Moreover, it was indicated that the solar still method for condensing/recovering the evaporated water of the Guerrero Negro salt pan is also less influential in the salt manufacturing process and is viable as a most economical distilling process by studying the structural design and operational method of more efficient solar stills

FY 1999 project on the development of new industry support type international standards. Standardization of evaluation method of the genetic testing system; 1999 nendo shinki sangyo shiengata kokusai hyojunka kaihatsu jigyo seika hokokusho. Idenshi kensa system no hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Aiming at applying standards as international standards, an experimental study was conducted on the standardization of the genetic testing system in Japan and abroad. The FY 1999 results were summarized. As to the unification of testing data processing, analysis of the present state and experimental study were made on the following: sampling method for appropriate testing, selection of anti-coagulants, method to preserve specimens, method to transport them, description of clinical observations in test request paper, method to evaluate performance of test reagents including restriction enzyme, temperature calibration method for equipment, sterilization method, incineration method of specimens, long-term storage of DNA samples, etc. The results were proposed as standard operation procedures after study/discussion at the comprehensive survey committee. Concerning the setting of criteria values in data analysis and the standardization of report form, survey/study were conducted also on ethical/legal/social problems from an aspect of privacy protection of patients. As a result, a total system from the reception of genetic testing to the report making was prepared. (NEDO)

Research cooperation project in fiscal 2000. Research cooperation on developing high-efficiency mineral resource extracting and processing technology of environment harmonizing type; 2000 nendo kenkyu kyoryoku jigyo. Kankyo chowagata kokoritsu kobutsushigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A joint research has been carried out in the Republic of Kazakhstan on a technology to extract and recover efficiently the valuable metals (copper, gold, silver and others) contained in ore wastes in large quantity, with considerations given to the environment. This paper summarizes the achievements in fiscal 2000 being the last fiscal year. This joint research has performed researches on the processing technology and processes, and on the operation research by using a pilot plant, using low-grade ores in the Nikolayevska Mine and ore wastes from the Zhezkent Mineral Dressing Mill as the objects. As a result of the researches, the following matters were discovered: if the ore wastes are used as the starting materials in the copper recovering process using the chemical leaching process, the copper price of $1,800 per ton is the breakeven point; economic effect is enhanced by grinding the starting materials into finer particles, adding a zinc recovery process, and recovering gold by using cyanogens; and this pilot plant is pollution free, and easy in maintenance and control. These processes were concluded effective in reducing the efficient waste ore processing and environmental cost being the environmental problem in Kazakhstan. (NEDO)

Achievement report for fiscal 1998 on the research cooperation project for a technology to facilitate setting forming conditions for engineering plastics; 1998 nendo engineering plastic no seikei joken kan'i settei gijutsu ni kansuru kenkyu kyoryoku jigyo seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

This project is intended to support plastics manufacturing being the important supporting industry in Thailand for manufacture of household electric appliances and automobiles, particularly the manufacture of engineering plastics having excellent heat and impact resistance. In order to achieve the target, a supporting system is being developed to allow injection molding of engineering plastics to be performed easily. The project aims particularly at developing a system that suits climate conditions in Thailand, properties of plastic materials procurable in Thailand, and skills of Thai engineers. The current fiscal year has carried out the following activities: evaluating materials required for the research and development, deciding the specifications for and ordering product evaluating and testing facilities, molds and mold cooling and heating adjustment devices, and an injection molding CAE system; these items were introduced and installed in Thailand; engineers were sent from Japan to perform technical guidance on operation, maintenance and management of the material and product evaluating and testing facilities, as well as joint researches; and Thai researchers were received to execute training on product evaluating and testing technologies, forming and processing technologies, and CAE utilizing technologies. (NEDO)

FY 2000 report on the survey of the project on field tests on the introduction of high performance industrial furnaces. Analysis/evaluation of the collected data; 2000 nendo koseino kogyoro donyu field test jigyo chosa hokokusho. Shushu data kaiseki hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of achieving the target of reduction in CO2 regarded as substance causing global warming which was agreed at COP3, the study has been made since FY 1993 on 'the development of high performance industrial furnaces (regenerative combustion furnace using heat storage type burner for realization of high temperature air combustion).' By applying the good results obtained, a field test project for introduction of high performance industrial furnace has been implemented for three years (FY 1998 - FY 2000) to confirm the actual performance, reliability, etc. Collection/arrangement were made mainly of the data obtained in this field test project for the introduction of high performance industrial furnaces in each fiscal year (1998, 1999 and 2000), and verification/evaluation and arrangement were made. In this R and D, energy conservation was achieved at a rate of more than 30% of the target. Also about NOx, the result was obtained that the NOx by energy saving can be reduced 50% in almost all kinds of furnace if adding the reduction amount in emission amount and the reduction amount by high temperature air combustion. About the quality, the good result was obtained. Downsizing was conducted in approximately 10 examples. (NEDO)

Research report for fiscal 1998 including researches into global environmental problems. Business report on the promotion of interaction of scientists over environmental problems in the Asia-Pacific region; 1998 nendo Asia/Taiheiyo chiiki kankyo mondai kenkyusha koryu sokushin jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Global environmental problems are growing quite serious in developing countries, yet they are requested to properly deal with them without making light of sustainable development, for which international cooperation and diffusion of technologies for the development of environmental technologies are mandatory. Japan, utilizing what it learned from pollution within in the past and making the best use of its technologies and knowledge for environmental improvement in developing countries in Asia, has been hosting since fiscal 1997 a function of Environmental Technology Research Network in the Asia-Pacific Region function. In fiscal 1998, a fifth international symposium was convened at Science City Center at the foot of Mt. Suzuka on November 26 and 27. The central theme was the development of environmental technologies and international cooperation for developing nations, and the event attracted 180 participants from inside Japan and abroad. A number of concrete themes came out of working groups on water quality, air quality, and energy/waste, which concerned the drafting of propositions for international collaborative researches. As for researches abroad, four typical Malaysian institutes were visited. (NEDO)

Fiscal 2000 feasibility research on environmentally-friendly coal utilization system. Feasibility research project (Clinkering technology for fluidized bed cement kiln - China); 2000 nendo kankyo chowagata sekitan riyo system kanosei chosa hokokusho. Jisshi kanosei chosa jigyo (ryudosho cement kiln shosei gijutsu Chugoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Studies are conducted about the feasibility of the above-named technology in China, its energy conservation and environmental protection effects, and so forth. To be expected upon conversion of shaft kilns in China to fluidized bed kilns using this technology are energy conservation of approximately 30%; resultant reduction in greenhouse effect gas emissions, in the scattering of coarse particulates, and in NOx and SOx emissions, these in combination contributing to reduction in environmental pollution; stable production of high-quality clinker; preference to inexpensive fuels and the effective utilization of resources; reduction in the cement manufacturing cost; and so forth. On-site surveys were conducted at existing shaft kiln plants, and studies were made about conversion to fluidized bed cement kilns with a 1,000 tons/day capability. The conclusion was that the period of return on invested capital would be 3.94-8.98 years, dependent upon the degree of facilities renovation, showing the presence of high possibilities of a successful return on invested capital. It was estimated that the shaft kilns would bring about a yearly reduction of 840 tons of coarse particulates, 105 tons of SO{sub 2}, and 68,281 tons of CO2. (NEDO)

FY 2000 report on the potential survey of implementation of a model project for improvement of thermal efficiency and energy conservation in refineries of Indonesia; 2000 nendo chosa hokokusho. Indonesia ni okeru seiyujo netsukoritsu kojo shoenergy model jigyo jisshi kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

For the purpose of heightening the thermal efficiency in oil refineries in Indonesia, survey was conducted of two main refineries of Pertamina (Cilacap Refinery and Balikpapan Refinery), and a potentiality of spreading energy conservation technology was studied. As a result of the study, the following were found out. In Cilacap Refinery, there is a possibility of energy conservation by enhancing the efficiency of the atmospheric distillation system and rationalizing utility facilities. As to Balikpapan Refinery, when effects of energy conservation are calculated by effectively using the by-producing off-gas emitted from the oil refining process which was recovered as on-site fuel, the amount of reduction in fuel consumption became 2.3 KL-FOE/h, and the year of simple investment recovery 1.7 years. Further, by recovering/effectively using hydrogen in the separation gas emitted from the hydrocracking unit, fuel/raw material in the hydrogen producing facilities were reduced, and the energy conservation effect became 2.98 KL-FOE/h in the amount of reduction in fuel consumption and 2.9 years in the year of simple investment recovery. (NEDO)

FY 1999 project on the development of new industry support type international standards. Comprehensive survey research on the promotion of international standardization; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kokusai hyojunka suishin ni kakawaru sogo chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of promoting the international standardization effectively/strategically, a comprehensive survey was made, and the FY 1999 results were summarized. In the trend survey on the comprehensive international standardization, survey was conducted for companies in the material field (plastics, rubber and iron steel) and in the mechanical field (robot, machinery, aircraft, etc.). As a result of the survey, it was found out that they have few headquarters systems and experts, but they tackle it strategically and defensively, taking the standardization as business. Also as to the trend of CEN/CENELEC, importance of the continued trend survey was pointed out. In the survey of policy for the international standardization, survey was carried out on the trend of the process for working out the international standards (TS, ITS and SDO). Further, in relation to the technology standards and intellectual property rights in the hi-tech field, survey was made on the present situation of rules for handling intellectual property rights of organizations, groups, etc. for standardization, how to handle intellectual property rights in the standardization process, problems and the solution, etc. (NEDO)

FY 2000 report on the survey of the project on field tests on the introduction of high performance industrial furnaces. Analysis/evaluation of the collected data; 2000 nendo koseino kogyoro donyu field test jigyo chosa hokokusho. Shushu data kaiseki hyoka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of achieving the target of reduction in CO2 regarded as substance causing global warming which was agreed at COP3, the study has been made since FY 1993 on 'the development of high performance industrial furnaces (regenerative combustion furnace using heat storage type burner for realization of high temperature air combustion).' By applying the good results obtained, a field test project for introduction of high performance industrial furnace has been implemented for three years (FY 1998 - FY 2000) to confirm the actual performance, reliability, etc. Collection/arrangement were made mainly of the data obtained in this field test project for the introduction of high performance industrial furnaces in each fiscal year (1998, 1999 and 2000), and verification/evaluation and arrangement were made. In this R and D, energy conservation was achieved at a rate of more than 30% of the target. Also about NOx, the result was obtained that the NOx by energy saving can be reduced 50% in almost all kinds of furnace if adding the reduction amount in emission amount and the reduction amount by high temperature air combustion. About the quality, the good result was obtained. Downsizing was conducted in approximately 10 examples. (NEDO)

Fiscal 2000 project for development of international standards for supporting novel industries. Standardization of methods for evaluating high-temperature physical properties of new glass; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo. New garasu koonbussei no hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development is under way about methods for evaluating the physical properties of high-temperature glass melt for the development of the methods into international standards. In this fiscal year, a technique of measuring high-temperature physical properties of amino silicate glass melt was developed, and the techniques of measuring high-temperature physical properties of molten soda lime glass and borate-silicate glass were improved. As the result, evaluation techniques compatible with international standards were developed for high-temperature glass melt physical properties such as viscosity, density, coefficient of volume expansion, surface tension, specific heat, thermal conductivity, electric conductivity, oxidation/reduction potentials, and the structure of molten glass. Techniques of evaluating gas solubility and the coefficient of gas diffusion, however, need further basic research and development. The author took part in a round robin test relating to the measurement of glass melt density and heat conductivity at CG/TC18, and measured the said two properties. The result of the round robin test was discussed at TC18 held in Amsterdam in May this year. (NEDO)

FY 1999 survey report on the cooperative basic project on the heightening of international energy consumption efficiency. Cooperative survey project in energy conservation/environmental protection fields in developing countries (Indonesia, Myanmar, the Philippines, Thailand and Vietnam); 1999 nendo kokusai energy shohi koritsuka nado kyoryoku kiso jigyo. Hatten tojokoku ni okeru sho energy kankyo hozen bun'ya kyoryoku chosa jigyo (Indonesia, Myanmar, Philippines, Tai, Vietnam)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

As to the pollution preventive administration, clean energy technology, etc. in fields of energy conservation technology, clean energy technology and environment in Japan, administrative officials, researchers and engineers in the fields concerned in Asian countries were invited to Japan for training with the aim of the technology transfer/spread to developing countries. In FY 1999, a total of 15 administrative officials and engineers were invited from Indonesia, Myanmar, the Philippines, Thailand and Vietnam, and had training at International Center for Environmental Technology Transfer. The themes for training are as follows: tackles with energy conservation/environmental protection by the Japanese government administration, pollution preventive measures against automobile gas emissions, pollution preventive measures against industrial gas emissions/waste water, technology for energy conservation, technology for industrial waste disposal, technology for recycling of wastes, etc. Reports were also made public on the situations of the countries participated in the project. Moreover, the field training was made at Yokkaichi complex, Sakakibara wind power plant, Hekinan thermal power plant of the Chubu Electric Power Co., Toyota Motor Corp., etc. (NEDO)

FY 1999 survey report on the cooperative basic project on the heightening of international energy consumption efficiency. Cooperative survey project in energy conservation/environmental protection fields in developing countries (Indonesia, Myanmar, the Philippines, Thailand and Vietnam); 1999 nendo kokusai energy shohi koritsuka nado kyoryoku kiso jigyo. Hatten tojokoku ni okeru sho energy kankyo hozen bun'ya kyoryoku chosa jigyo (Indonesia, Myanmar, Philippines, Tai, Vietnam)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

As to the pollution preventive administration, clean energy technology, etc. in fields of energy conservation technology, clean energy technology and environment in Japan, administrative officials, researchers and engineers in the fields concerned in Asian countries were invited to Japan for training with the aim of the technology transfer/spread to developing countries. In FY 1999, a total of 15 administrative officials and engineers were invited from Indonesia, Myanmar, the Philippines, Thailand and Vietnam, and had training at International Center for Environmental Technology Transfer. The themes for training are as follows: tackles with energy conservation/environmental protection by the Japanese government administration, pollution preventive measures against automobile gas emissions, pollution preventive measures against industrial gas emissions/waste water, technology for energy conservation, technology for industrial waste disposal, technology for recycling of wastes, etc. Reports were also made public on the situations of the countries participated in the project. Moreover, the field training was made at Yokkaichi complex, Sakakibara wind power plant, Hekinan thermal power plant of the Chubu Electric Power Co., Toyota Motor Corp., etc. (NEDO)

Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium energy field / R and D of a task adaptation type group architecture transfer robot system, TRIPTERS (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium energy bun`ya / task tekigogata gun kosei hanso robot system TRIPTERS no kaihatsu kenkyu (daiichi nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper stated the fiscal 1997 result of the development of a task adaptation type group architecture transfer robot system (TRIPTERS) which can cope with changes in carrying task rapidly and flexibly. R and D were conducted mainly of various functional modules, the operation management technology which enables group architecture, and the basic design of a standardized transfer robot. As to the positioning, studied were the construction of the basic hardware of laser position measuring device, and the application method. Concerning the cooperative carrying, conducted were securing of positioning accuracy of matters to be carried, high speed heavy transfer control, and design of dead reckoning system. Relating to the operation management, passable areas were divided into more than one zones, and the effective path reservation method was constructed so that one and the same zone is not occupied. As to the environmental recognition/obstacle avoidance, developed were actual hour/distance acquisition equipment, and autonomous cars running according to the directions of the color sign recognition system by stereo CCD camera. Also conducted were the development of methods to recognize the distance to obstacles and to discriminate areas, the development of mobile sensor, and the basic experiment on running of the demonstration machine. 44 refs., 153 figs., 15 tabs.

FY 2000 report on the results of the regional consortium R and D project - Regional consortium R and D field. First year report. Development of an on-line/real-time dioxin measuring system; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium kenkyu kaihatsu bun'ya. Dioxin no on line real time keisoku sochi no kaihatsu (dai 1 nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the supersonic molecular jet resonance multiple photon ionization mass analysis method (SSJ method) as basement technology, the development was proceeded with of a portable dioxin spectrometer to measure dioxins emitted from incinerator on line and at real time and to control/improve the state of combustion. Studies were made in the following three fields: 1) development of pico second wavelength variable color laser; 2) development of a flight hour type mass spectrometer; 3) development of the pretreatment technology suitable for analysis of dioxins, precursors, etc. by supersonic molecular jet spectroscopy. In 1), the prototype was fabricated to assess the performance, and it was confirmed that the prototype has the targeted characteristics. In 2), as to the coaxial ionization and ring double skimmer electrode system, the convergence and mass resolution of ion were measured, and a possibility of the commercialization was obtained. In 3), it was confirmed that there is a possibility in rapid pretreatment by alumina fiber filter. (NEDO)

FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy field. Final year report. R and D on the bio-fuel production by high functional bio-reactor; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy bun'ya. Kokino bio reactor ni yoru bio nenryo seisan ni kansuru kenkyu kaihatsu (saishu nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A system was developed for producing automobile fuel from the recycled paper and waste cooking oil using high functional intelligent yeast. Element technology is the functional yeast creation technology and the online intelligent control technology of the process into which the fixed bio-reactor was inserted. Studies were made on the following: 1) creation of high activity lipase production/ethanol production yeasts; 2) bio-fuel production by intelligent bio-reactor; 3) process optimization control technology by fuzzy control; 4) stabilization of bio-fuel production yeast; 5) comprehensive investigational study. In FY 2000, the results were obtained as written below: development of the stable lipase coming from rhizopus japonicus, fixed bacterium using rhizopus oryzae fungus body which can be used more than ten times, direct ethanol fermentation from starch by developing the multi-copy glucoamylase manifestation yeast, operation of a 20L capacity bench plant, etc. (NEDO)

Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium energy field / Development of the plasma use surface treatment process by in-situ control (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium energy bun`ya / in-situ seigyo ni yoru plasma riyo hyohi shori process no kaihatsu (daiichi nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper described the fiscal 1997 result of the development. To know of in-plasma phenomena such as carburization and nitriding, a basic plasma experimental device was fabricated for quantitative measurement of reaction activity species. For the study of reaction control between plasma and substrate, a rotary analyzer type ellipsometer was fabricated as a method to detect composition and thickness of the deposit on the substrate surface. For He gas cooling after carburization and hardening, basic specifications for He gas refining/circulating system were confirmed. For perfect non-hazardous processing of exhaust gas from plasma carburization furnace, conducted was the thermodynamic computation of the process. Priority in order of the functions to be possessed as specifications for basic design of mini plant is plasma carburization, He gas cooling, and in-situ measurement. To make the most of the plasma use surface treatment as substitutes for expensive alloy elements, sliding parts/die-cast mold raw materials were carburized to measure the hardness. The Cr carbide coating technology by plasma CVD is also under study as an application example except carburization. 47 refs., 59 figs., 31 tabs.

FY 2000 report on the results of the regional consortium R and D project - Regional new technology creation R and D. First year report. R and D of medicine toxicity assessment use hepatocyte chip; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium kenkyu kaihatsu / chiiki shingijutsu soshutsu kenkyu kaihatsu. Dokubutsu dokusei hyokayo kansaibo chip no kenkyu kaihatsu (dai 1 nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Judging that in the beginning of the toxicity test, the necessary information/knowledge are acquired not by using animal itself but only by using liver system (hepatocyte), the development was proceeded with of the hepatocyte chip substituting for the animal experiment. Studies were made in the following five fields: 1) design of functional matrices; 2) development of the pharmacological assessment technology; 3) development of cell sensing technology/biosensor fabrication; 4) study of a possibility and the limit of cell patterning technology; 5) survey of the market scale. In 1), studies were made of the establishment of the 3D culture method for hepatocyte and the construction of hepatocyte models for medicine assessment using pieces of liver. In the latter, by including capsule using the sugar introduced with galactose residue which is special sugar of hepatocyte to alginic acid and chitosan which are natural polymer and also hepatocyte isolated into sponge, aggregate was formed, and its use as a medicine assessment use liver model was tried to be made. (NEDO)

FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D. Third year report. R and D of a hybrid pulse plasma coating (HPPC) system; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu. Hybrid gata pulse plasma coating (HPPC) system no kenkyu kaihatsu (dai 3 nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The development was proceeded with of the surface reforming technology system in which plasma CVD technology and PSII (plasma source ion implantation) technology are connected. HPPC forms DLC (diamond like carbon) layers excellent in adhesion and ceramic layers on the surface of work pieces such as complicatedly shaped dies and tools/sliding parts. Element technologies are the raw material gas pulse introducing technology for efficiently introducing raw materials into the reaction container in a state of gas, high density plasma formation technology and pulse plasma formation technology, minus pulse voltage application technology for vertically implanting various ions on the surface of complicatedly shaped work pieces, and advanced hybrid control technology enabling the control of ion species/implantation amount/layer formation speed. In FY 2000, using the prototype of the HPPC system, studies were made of the development of the DLC layer process and the low temperature DLC layer process, and development and commercialization of technology to improve throwing power, etc. (NEDO)

Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium field / Development of medical equipment use super devices using micro-3D processing technology (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium bun`ya / micro sanjigen kako gijutsu ni yoru iryo kikiyo super device no kaihatsu (daiichi nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The R and D are conducted of medical equipment use super devices using technical seeds of Mechanical Engineering Laboratory and micro-3D processing technology which was developed from precision processing technology, etc. which is integrated in the Suwa area, Nagano prefecture. For it, the following R and D are carried out: 1) development of micromechanism: DC3V driven micromotor, chemical use microtube with diameter of 0.1mm, micro-delivery mechanism of chemicals, misting mechanism of chemicals, microjoint, microconnector and cable, and microfilter. 2) development of microsensor: small size/non-contact, microflow of chemicals, and sensor to detect emission of bubble. 3) development of control system. In fiscal 1997, in 1), each element was trially made to clarify subjects. In 2), it was made clear that as flow sensor, ultrasonic type, electromagnetic type and thermal mass flow type are viable, and as bubble sensor, optical sensor is viable. In 3), the following were conducted: information collection of contactless charging circuit, and trial fabrication of liquid crystal polymer ultra thin casing. 9 refs., 84 figs., 30 tabs.

FY 2000 report on the results of the regional consortium R and D project - Regional consortium field. Second year report. Development of the technology to combine plastic and metal using biodegradable natural polymer; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium bun'ya. Seibunkaisei tennen plastic to kinzoku no fukugoka gijutsu no kaihatsu (dai 2 nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The development was proceeded with of the electromagnetic wave shielding technology composed of plastic body, chitosan containing biodegradable coating and electroless metal plating layer. Key technologies are for formation of biodegradable electroless plating use coating using chitosan as chemical adsorption carrier of Pd and for separation of the body and the metal thin film by the environment-harmony method for recovery of the material. Studies were made in the following 5 fields: 1) method to produce low molecular chitin and chitosan; 2) application of biodegradable materials to electromagnetic wave shielding; 3) evaluation of physical properties and function of a new electromagnetic wave shielding system; 4) R and D of the degradation method of the new electromagnetic wave shielding system; 5) comprehensive investigational study. In FY 2000, in 1), conditions for production of chitosan degrading enzymes were determined, and also the scale of bio-reactor was increased up to 20L. Further, chitosan was so re-synthesized that it disperses to the electroless plating use primer. (NEDO)

Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium energy field / Development of an environmentally friendly industrial cleaning system using near-critical and supercritical carbon dioxide (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium energy bun`ya / chorinkai ryutai wo mochiita kankyo chowagata kogyo senjo sochi no kaihatsu (daiichi nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In the manufacturing process of semiconductors and in the high tech industry, cleaning is indispensable. At present, when regulation of the use of CFC which used to be much used has been decided on, the conversion to the use of substitutes for CFC cleaning is urgently needed. Transfer to cleaning by water/alcohol/hydrocarbon has been proceeded with, but there are a lot of problems. Out of the development of the cleaning method using supercritical fluid, the paper described the fiscal 1997 result. As to enhancement of efficiency and decrease in size of equipment, a cleaning experiment by high pressure CO2 around the critical point was conducted by integrating nozzle, ultrasonic generator and cavitation generator and adding solvent circulating system. Multi-purpose and energy saving of the equipment were also studied. To establish an analysis method for the cleaning degree, the contaminated component film of trace organic matter with a specified thickness was formed on the silicon wafer, and using the Fourier transform ultrared spectroscopy, a method to determine the film thickness was studied. For the function evaluation for precision machine parts and determination of optimum cleaning conditions, the cleaning/degreasing process of valves were compared with the conventional method. For the product manufacturing, the paper investigated and prepared the data in Japan and from abroad. 55 refs., 79 figs., 18 tabs.

FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D field. First year report. R and D of new composite polymer electrolyte for battery; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu bun'ya. Denchiyo shinki fukugo polymer kei denkaishitsu no kenkyu kaihatsu (dai 1 nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The development was proceeded with of new composite polymer electrolyte for Li secondary battery. The ultimate target of the development using this electrolyte is to get Li secondary battery markedly improved in safety/reliability which works at low temperature and controls thermal runaway. The composite polymer base electrolyte is composed of high molecular weight polyethylene oxide copolymer, ethylene oxide oligomer and Li salt, and it is finally cross-linked by heat or light. Studies were made in the following 6 fields: 1) R and D of the creation and optimization of new composite polymer electrolyte; 2) R and D of the commercialization of composite polymer electrolyte battery; 3) R and D on the safety of composite polymer electrolyte; 4) study of the synthesis of new electrolyte and catalytic activity of electrolyte-electrode interface; 5) R and D on polymer/oligomer composite electrolyte; and 6) comprehensive investigational research. (NEDO)

Project in fiscal 2000 of developing international standards for supporting new industries. Standardization of method for evaluating thermal properties test on polymeric materials; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kobunshi zairyo no netsutokusei shiken hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Targeting at proposing to ISO as an international standard, R and D has been performed on a method of the alternating current heating of the non-constant method, with regard to a method to evaluate the thermal properties test on polymeric materials in molten condition reflecting thin film polymeric materials, and the forming and processing technology. This paper summarizes the achievements in fiscal 2000. The current fiscal year has executed surveys on literatures related to thermal properties, development and commercialization of a measuring device, establishment of the measurement procedure, and putting some of the materials into database. The database was prepared mainly for heat diffusion rate and heat conductivity, wherein about 1000 items of information were collected. The temperature range of the measuring device revealed that stabilized data can be obtained from as low temperature as liquid nitrogen temperature to as high as 200 degrees C. The commercially available measuring device has no restrictions if the test sample thickness is from 1 mm to 100 mm, if the temperature range is from room temperature to 350 degrees C, if the temperature rising rate is from 0.01 to 5 K/min, and if the test sample form is film. Measurement at temperatures including those in the melting zone in the forming stage of each polymer has achieved as close result as having been called for in the initial objective. (NEDO)

Fiscal 2000 project for development of international standards for supporting novel industries. Standardization of fine ceramics test and evaluation method for communication equipment; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo. Tsushinkiki yo fain ceramics no shiken hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development is carried out aiming at the international standardization of methods for evaluating electric properties such as dielectric constant, dielectric loss, and surface resistance for fine ceramics for use in the high-frequency and ultrahigh-frequency bands. In this fiscal year, in the effort to establish an accurate measurement method for millimeter wave complex specific inductive capacity, the Fabry-Perot resonator was improved, and found to be capable of measuring 60-110 GHz. Efforts were made to improve on the accuracy of the cavity resonator excited by coaxial cable, for which various types of resonators were fabricated. For the calibration of evaluation apparatuses such as the Fabry-Perot resonator, cavity resonator excited by coaxial cable, and dielectric resonator excited by non-radiative waveguide, sapphire single crystals and PTFE (polytetrafluoroethylene) were selected as reference materials for measuring complex dielectric constant, and their dimensions and specifications were determined. In the study of the evaluation of basic surface properties, surface irregularity of the silver electrode was accurately measured by use of a thin-film surface geometry measurement apparatus, and the presence of a strong correlation between the jig silver electrode surface coarseness and the microwave band effective conductivity. (NEDO)

Project in fiscal 2000 of developing international standards for supporting new industries. Standardization of method for calculating recycling rate of automotive products; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Jidosha seihin no recycle ritsu no santei hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With international standardization as a target, research has been performed for three years since fiscal 1998 on a method for calculating the recycling rate of automotive products. This paper summarizes the achievements thereof. In fiscal 1998, studies were conducted on major automobile materials, state of recycling in Japan and Europe, and trial monitoring on recycling execution rate in the dismantling and shredding stages. Despite uncertainties that remain in recycling, the importance of standardization has been affirmed. Beginning in fiscal 1999, discussions have been given on requirements for establishing the recycling possibility by means of dismantling automobiles. In the requirements for establishing thermal recycling, discussions were given, taking into account the state of legal regulations in Germany and the trial execution of the container and packaging recycling law in Japan. As a result, the standard draft for the method for calculating the recycling rate was established for automotive products, including the method for calculating the recycling possibility rate, and the requirements for establishing thermal recycling. For international standardization of the method for calculating the recycling possibility rate, discussions have begun at ISO/TC22/WG10. (NEDO)

Fiscal 2000 project for development of international standards for supporting novel industries. Standardization of digital image processing for domestic digital electronic equipment; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo. Kateiyo digital denshi kiki ni okeru digital gazo shori no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Three-year research and development had been under way since fiscal 1998 for the establishment of global standards for domestic digital electronic equipment. In this last fiscal year of the project, emphasis was placed on supporting Japanese corporations concerned so that they would submit propositions relative to an expanded IPMP (Intellectual Property Management and Protection) system. First, Japan's technical propositions as to how to assure interchangeability between terminal devices were reviewed. Next, reviews were made of technical propositions and propositions for their application involving interface conversion and protocol conversion at content servers and RA servers, functional augmentation of roaming service, and the like. Support was provided for activities aiming at their global-scale standardization and for the preparation of groundwork materials for persons concerned with the technical committee involved. In relation to verification tests for supporting this project, system models, simulation models, and the like, were constructed. In relation to WD3.0 of IPMP, Japan's propositions were incorporated into its core, and this proved to be the major accomplishment under this project. (NEDO)

Fiscal 2000 project for development of international standards for supporting novel industries. Standardization of methods for testing and evaluating corrosion resistance of surface treated steel sheets; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo. Hyomenshori kohan no taishokusei hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With a view to presenting the result to ISO (International Organization for Standardization), studies were conducted of accelerated test and evaluation methods capable of promptly reproducing the state of corrosion generated during outdoor exposure tests of surface treated steel sheets. In the study of a wet rate evaluation test, a cycle test was carried out at a wet rate of 25-75% under the conditions of an artificial seawater concentration level of 6.0g/L, equivalence ratio of 0.2, and pH of 2.5, and it was found that a wet rate of 50% was appropriate. For comparison of a rain of pH 2.5 with a rain of pH 3.0 in an acid rain pH evaluation test, a cycle test was conducted at pH 3.0 under the conditions of an artificial seawater concentration level of 6.0g/L, equivalence ratio of 0.2, and a wet rate of 50%, and the result indicated that pH 2.5 was more realistic than pH 3.0. As a comprehensive test, a cycle test was conducted comprising 1 hour of acid rain spray, 4 hours of dry spell, and 3 hours of moist spell under the conditions of an artificial seawater concentration level of 6.0g/L, equivalence ratio of 0.2, wet rate of 50%, and pH of 2.5, and the resultant data were found to be correlative to the data obtained at Naoetsu. Based on the findings, a ground plan was drafted for an international standard relative to methods for testing and evaluating surface treated steel sheets for corrosion resistance. (NEDO)

Fiscal 1999 survey report on basic feasibility in implementing model project for efficient consumption of energy by fiber dyeing and processing plant in Indonesia; 1999 nendo Indonesia ni okeru senshoku kako kojo energy shohi koritsuka model jigyo kihonteki jisshi kanosei chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The basic feasibility of a model project was investigated for the purpose of introducing energy saving technology in dyeing and processing by the textile industry, which consumes a great deal of energy in Indonesia. This paper explains the result of fiscal 1999. A questionnaire survey was conducted on 40 companies having a continuous processing plant from spinning to finishing, while seven companies among them were visited for the survey on the status of energy consumption and conservation. Meantime, a survey was also made on the related policies and the state of their implementation in Indonesia as well as on the status of investment on equipment. As energy saving measures for the processing, proposals were made for energy saving in the washing process (exhaust-heat recovery system, monitoring system, and optimization of steam usage in drying process), for introduction of a heat pump system, and for reduced energy consumption in a jet dyeing machine. As energy conservation measures for utilities, reduced energy consumption of boilers was proposed, as was introduction of co-generation system. Essential for the dissemination of the measures are guidance, enlightenment and mentality reform for the entrepreneurs. Needed for the policy are the establishment of a core organization for energy conservation, plans, analyses, model projects, and introduction of an economic support system (e.g., low-interest loan). (NEDO)

Project in fiscal 2000 of developing international standards for supporting new industries. Comprehensive surveys and researches in relation with promotion of international standardization; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kokusai hyojunka suishin ni kakawaru sogo chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective of promoting the international standardization efficiently and strategically, surveys were performed on trends of international standardization in Europe and America, and researches on means for the international standardization. The standards strategy in the U.S. is to increase the U.S. competitive power in overseas countries, support strongly the domestic markets, and at the same time, deal with problems such as those of the environment. It attempts to structure a framework that can be utilized by any concerned parties, including business entities, the government, and consumers, whereas the National Standards Strategy (NSS) has proposed the initiative. In Europe, targeting to establish international standards originated from Europe, works are becoming more active for new technologies such as information communicating technologies from the R and D phase to the test and evaluation methods, taking the standardization into consideration. These works are being carried out within the scope of the common EU R and D, represented by the 'Framework program' and the 'EUREKA program'. In the survey and research on means to complete the international standardization, analyses and surveys were performed on the latest information, such as TC/SC, which are scheduled of proposition. Advices were given on giving the directionality and establishing the strategy. (NEDO)

Project in fiscal 2000 of developing international standards for supporting new industries. Standardization of method for measuring fuel consumption of hybrid electric automobile; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Hybrid denki jidosha no nenpi sokutei hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With proposal of a standard draft to ISO as a target, R and D has been performed for three years since fiscal 1998 on a method for measuring fuel consumption of hybrid electric automobiles. This paper summarizes the achievements thereof. In the R and D, analyses were conducted on elements particular to a hybrid system considered to influence the fuel consumption, such as the remaining capacity in the main batteries, fuel consumption for regenerative braking, and effects on exhaust gas. As a result, it was revealed that correction is required for change in the remaining capacity in the main batteries before and after the test with regard to the fuel consumption, and that this is possible. Discussions were given on a method for fuel consumption test by using the driving modes adopted in Japan, America and Europe using four types of HEV having different hybrid systems and mounted batteries. Comparisons and discussions were given on the 'continuously repeated mode averaging method','primary approximation method' and 'SAEJ1711 and its test establishment criteria'. As a result, the primary approximation method was proved to be the best as the HEV fuel consumption test method. At the same time, necessity of standardizing the current measuring device and the measuring method was pointed out in the fuel consumption measurement using the primary approximation method and SAEJ1711. (NEDO)

FY 2000 research cooperation project for the research cooperative follow-up on the technology to simply set molding conditions of engineering plastics; 2000 nendo kenkyu kyoryoku jigyo. Enjiniaringu plastic no seikei joken kan'i settei gijutsu ni kansuru kenkyu kyoryoku follow up

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of supporting improvement of the plastic molding industry which is the important industry supporting industries such as household electric appliances and automobiles, the joint research was made on the production of high quality/high precision engineering plastic formed products, and the FY 2000 results were reported. In this fiscal year, the domestic support committee, ' the engineering plastic molding technology research committee' was held twice, and the following were carried out: discussion about the research plan, study of a plan for Japanese researchers to be sent and the details of the joint research, comprehensive evaluation of the results of the joint research made on the site. In the joint research at Thailand's BSID (Bureau of Supporting Industries Development), 4 engineers of molding technology/testing technology were sent from Japan during the period from September 18, 2000 to January 24, 2001, and the following were carried out: theoretical study and practical guidance for comprehension of injection molding technology, establishment of optimum conditions for injection molding and practice of measures taken against bad molding, conduction of the round robin test/comparative study by both JCII (Japan Chemical Innovation Institute) and BSID, etc. (NEDO)

FY 1999 project on the development of new industry support type international standards. Standardization of methods to test/evaluate plastic optical fiber; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Plastic hikari fiber no shiken hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The experimental research was conducted with the aim of developing test/evaluation methods of plastic optical fiber (POF) and proposing a draft on the standards to IEC, and the FY 1999 results were outlined. In the study of the band measuring method, the equipment designed was compared/verified in the pulse method with the frequency sweep method equipment for quartz base optical fiber use to confirm the accordance. Effects were further studied of experimental conditions including exciting conditions. Also about the frequency sweep method, the same verification was made to see the accordance with POF measured values in the pulse method. In the analysis by theoretical calculation, obtained were the results by which the experimental results can almost be explained. In the experiment on the optical transmission, the bit-error-rate was measured by transmitting digital signals to POF. As a result, it was confirmed that there were close relations between the band width of POF, bit-error-rate and changes in receiving sensitivity. As to the above-mentioned band experimental method, strategy for standardization was studied, and the making of a draft on the standards was started which is to be proposed at the meeting of TC86/SC86/WG1. (NEDO)

Research cooperation promotion business for fiscal 1998. Research cooperation in the development of environmentally-friendly high-efficiency mineral resources extracting and processing technologies; 1998 nendo kenkyu kyoryoku suishin jigyo. Kankyo chowagata kokoritsu kobutsu shigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Research cooperation was conducted in the Republic of Kazakhstan for efficiently extracting and collecting valuable metals (gold, silver, copper, and rare metals) contained in volume in the slag generated by mining operation, with caution exercised not to disturb the environment. The research items taken up for development involved technologies of the leaching of the target elements using sulfuric acid, microbes, etc.; extraction using solvents; electroextraction; collection of gold and silver; and the treatment of waste water. In fiscal 1998, the wet process and the processing of gold and silver were studied, for which the specimens sampled at the research site in and after fiscal 1996 were used. As for the fabrication of pilot plant facilities, all were completed in fiscal 1998, and part of them was transported to the research site. Procurement and transportation necessary for the joint research were also carried out. Furthermore, to ensure effective execution of the project, scientists were invited from Vniitsvetmet, the Kazakhstan research institute for non-ferrous metals, for training, who included the institute director, deputy director, patent/liaison department chief, and two researchers. (NEDO)

Research report for fiscal 1998. Evaluation and analysis of the collected data for the field tests on photovoltaic power generation systems for public facilities; 1998 nendo kokyo shisetsu nado yo taiyoko hatsuden field test jigyo ni okeru shushu data hyoka kaiseki kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The field tests on photovoltaic power generation systems for public facilities have begun in fiscal 1992 by NEDO. The systems including those under construction are installed in 116 sites. Analyses were given on 75 sites which have been operated up to fiscal 1996. Analyses of the operation characteristics were performed by using performance parameters derived by developing the basic expressions into each configuration element. For the insolation on slanted surface, the range from 3.0 to 4.5 kWh/m{sup 2}/D accounts for 65% of the total insolation. For the equivalent array operation time, the range from 2.5 to 4.0 h/D accounted for 81%. For the equivalent system operation time, the range from 9.0 to 12.0 h/D accounted for 85%. The range for inverter active efficiency from 0.84 to 0.96 accounted for 79%. The inverter load rate was accounted for 88% by 0.20 to 0.35. The output coefficient was accounted for 82% by 0.7 to 1.0 in the array, and 87% by 0.6 to 0.9 in the system. The power generation cost has decreased to 200 yen per kwh in fiscal 1995 from 340 yen per kwh in fiscal 1992, largely contributed by reduced installation cost. (NEDO)

Fiscal 2000 project for development of international standards for supporting novel industries. Standardization of digital image processing for domestic digital electronic equipment; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo. Kateiyo digital denshi kiki ni okeru digital gazo shori no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Three-year research and development had been under way since fiscal 1998 for the establishment of global standards for domestic digital electronic equipment. In this last fiscal year of the project, emphasis was placed on supporting Japanese corporations concerned so that they would submit propositions relative to an expanded IPMP (Intellectual Property Management and Protection) system. First, Japan's technical propositions as to how to assure interchangeability between terminal devices were reviewed. Next, reviews were made of technical propositions and propositions for their application involving interface conversion and protocol conversion at content servers and RA servers, functional augmentation of roaming service, and the like. Support was provided for activities aiming at their global-scale standardization and for the preparation of groundwork materials for persons concerned with the technical committee involved. In relation to verification tests for supporting this project, system models, simulation models, and the like, were constructed. In relation to WD3.0 of IPMP, Japan's propositions were incorporated into its core, and this proved to be the major accomplishment under this project. (NEDO)

FY 2000 report on the basic survey to promote Joint Implementation, etc. Project for improvement of efficiency of the power generation/desalination plant in Aktau City; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Aktau shi hatsuden zosui plant koritsu kaizen jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of conserving energy and reducing greenhouse effect gas emission, feasibility study was conducted for improvement of efficiency of power generation/desalination facilities at MAEK Energy Center, Aktau City, Manghistau, Kazakhstan. Presently, the main facilities are the conventional natural gas fired power plant, evaporation type seawater desalination facility, hot water production facility, etc. In the project, introduction of the following was planned to be made: cogeneration facility composed of two units of 1,100-degree C class gas turbine and reverse osmosis (RO) type desalination facility for drinking water production with a capacity of 50,000 t/d. As a result of the study, the energy conservation amount in this project was 151,900-165,400 toe/y in power generation facility, and the greenhouse effect gas reduction amount was 355,000-387,000 t-CO2/y in power generation facility and 268,000 t-CO2/y in desalination facility. The construction cost and operational cost of the plant were 45.7 billion yen and 2.8 billion yen/y. In the economical estimation, ROI and ROE before tax were 7.4 and 34.8, respectively, which were considered to be appropriate values as social infrastructure related conditions. (NEDO)

Report on the results of the fiscal 1997 international research cooperation project. `Joint R and D industrial base technology` (development of functionally graded materials); 1997 nendo kokusai kyoryoku jigyo. `Sangyo kiban gijutsu kyodo kenkyu kaihatsu` keisha kinosei zairyo no kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

For the purpose of developing functionally graded materials (FGM/LB) of thermal stress relaxation heat resistant large bulk state which are adoptable to high efficiency engine members, conducted in fiscal 1997 as intermediate target were the experiment for enlargement of the sintering process of FGM/LB with bore of up to 100mm, evaluation of physical properties, the basic development of the fabricating system facility for the commercialization. In the development of heat resistance use FGM/LB fabrication technology, to obtain ZrO2(3Y) stainless steel system FGM/LB, the following were fabricated in each bore size of 50-100mm by the research use large discharge plasma sintering machine: sintered bodies of ceramics/metal single substrate materials and mixed layer single substance materials, and FGM/LB sintered bodies without separation and crack which are composed of 9 intermediate graded layers. The survey was also made on the optimal composition and optimal sintering conditions toward the enlargement without unevenness. In the evaluation of physical properties, ZrO2(3Y)/stainless steel system was selected and test pieces were fabricated to obtain basic data on texture observation, distribution of hardness, fracture toughness, high temperature abrasion resistance, thermal expansion rates, etc. 27 refs., 108 figs., 43 tabs.

Fiscal 2000 survey report. Survey for verification of new load levelling technique - IEA international joint project (Participation in IEA/DSM task); 2000 nendo fuka heijunka shuho jissho chosa hokokusho. IEA kokusai kyoryoku jigyo 'IEA/DSM task eno sanka ni tsuite'

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Japan participated in IEA/DSM (International Energy Agency/demand side management) Task X (performance contracting) for collecting information on energy service contracting business designed to promote load levelling centered DSM activities on the basis of market principles for achieving efficient operation of facilities. Task X aims to adjust and popularize the energy service contracting business. In the energy service contracting business, the facility related party and the energy service related party work under a contract to enhance efficiency of facility operation, and share the gains between them. In concrete terms, information was collected and exchanged at the 14th and 15th executive committee meeting of IEA/DSM Task X (Turkey in April 2000, Sweden in September 2000); new task preparation conference (Sweden in September 2000); 1st specialist conference (France in February 2001); and 17th annual convention of All-America ESCO (energy service company) Council (U.S. in November 2000). (NEDO)

Fiscal 2000 strategic surveys for respective technical fields. Hydrogen-based energy working group (Analysis of project results relating to hydrogen technology); 2000 nendo bun'yabetsu senryaku chosa hokokusho. Suisokei energy WG (Suiso kanren gijutsu ni kakawaru jigyo seika tou bunseki chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Attention is focused on the molten carbonate fuel cell (MCFC) technology which has enjoyed the largest number of industrial property applications out of hydrogen-related technologies under development by NEDO (New Energy and Industrial Technology Development Organization). The patent application is utilized as a tool for analysis, and endeavors are made to systematize and then analyze the correlations between the tasks to discharge and the results of studies in the process of MCFC development. Findings are described below. It is quite difficult to specify the technology involved by the study of patent abstracts. Since an applicant for patent is inclined to describe the application so that it will cover an extensive scope (or, so that the patent will be taken in a broad sense), it takes much time for researchers other than the applicant to specify the field of technological studies where the application originates. Such being the case, it cannot be easily determined whether or not a patent applied for by a private-sector corporation has its origin in a NEDO-implemented project. In addition, it is found that there is not necessarily a correlationship between the importance of a research and development goal and the number of patents generated. (NEDO)

Fiscal 1999 technical achievement report. Research and development project on the quickly effective international standards creation (Standardization of information security system evaluating methods); 1999 nendo sokkogata kokusai hyojun sosei kenkyu kaihatsu jigyo seika hokokusho. Joho security system no hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For standardization under information security evaluation criteria, an evaluating technique CEM (Common Methodology for Information Technology Security Evaluation) was constructed as ISI/IEC15408. The method, however, is abstract in content and the evaluation work thereunder requires much time and accompanies economic difficulties. In dealing with the situation, investigations were conducted into security evaluation related techniques and manufacturing/quality control techniques in use at information processing product developing sites, and a CEM technique is materialized. Using the proposed technique, developers themselves can evaluate security in the development process and workloads imposed on evaluating organizations may be reduced because evidential items necessary for 3rd party evaluation may be gathered. Since the developed technique is verified by an official evaluating organization, it is expected to be an effective techniques not contradicting existing operating techniques. It may be also said that this technique is a method whereby developers will collect evidential items necessary for their development efforts. The result will be presented in the form of a proposal for an evaluating techniques standard for ISO/IEC JTC1 SC27. (NEDO)

Fiscal 2000 achievement report on the venture business assisting type regional consortium - Minor business creation base type. Research and development of smart catheter for omnidirectional diagnosis; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Zenhoi shindan smart catheter no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The aim is to develop a highly reliable device for detecting pathological developments deep inside the body by combining the pulse compression technique used in high performance radars and a quartz fiber. The project also aims to develop a system which, when compared with the conventional method, is capable of higher resolution at a short range and of reaching farther for the same resolution level. To be contrived for the development of a diagnostic catheter which combinedly uses the ultrasonic pulse compression and imaging technology and an optical picture system are a pulse signal reflection mirror for taking in ultrasonic picture data on the front and the sides in the lumen, an ultrasonic micromotor for rotating the mirror, and a high efficiency ultrasonic transducer similar in size to the waveguide for transmitting ultrasonic pulses to a quartz waveguide from outside the body and for receiving reflected signals. An effort is simultaneously exerted to make the diameter smaller of a quartz waveguide to be built in the catheter to provide a signal passage for the ultrasonic imaging system and the optical picture system for the realization of a catheter tip smaller and thinner as a whole. A study is made about a mechanical-electronic control system for easy luminal insertion. (NEDO)

FY2000 report of the research results on medical/engineering cooperative research project, fundamental research for minimally invasive/super-selective localized diagnosis and treatment; 2000 nendo igaku kogaku renkeigata kenkyu jigyo teishinshu kokando sentakuteki kyokusho shindan chiryo ichigenka system no kiban kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

The research and development efforts are made for super-selective localized diagnosis and treatment and simultaneous observation of the treatment results at the catheter edge point, based on the molecular biology and gene engineering methods, and the FY 2000 results are reported. The program for investigating the catheter hardware designs include the diagrammatic evaluation of a multi-lumen multi-functional laparoscope and pancreatoscope for localized diagnosis and medical treatment. The program for development of diagnostic technology leads to development of double staining of cancer cells and macrophage, which allows the in vivo analysis of the cell-to-cell interactions. The program for studying the technology related to affective genes which can be diagnosed and treated by a catheter includes cloning of genes for therapy of chronic glomerular nephritis and adrenal neoplasm, and those for liver regeneration. The program for method of local delivery of genes includes studies on therapy of metastatic cancer of lymph node using liposome and adenovirus as a gene carrier, and on pulse laser delivery for local and efficient delivery of the genes. (NEDO)

Achievement report for fiscal 1999 on the development of total evaluation research laboratory system for the medical welfare equipment technology research and development project; 1999 nendo iryo fukushi kiki gijutsu kenkyu kaihatsu project yo sogo hyoka kenkyu rabo system kaihatsu jigyo seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

A laboratory system named above has been developed to propel forward efficiently the efforts to develop medical welfare technologies through close coordination between medicine and engineering. Six laboratories are linked with each other in a network for the realization of an environment in which general support is extended to all the stages of equipment development from basic through clinical assessment. The biomedical engineering laboratory is constituted of various analyzing devices, and is capable of in vitro assessment of bioingredients. The therapeutic laboratory is provided with bioinformation/NMR (nuclear magnetic resonance) measurement equipment, animal surgical operation equipment, etc., and performs the assessment of test animals at the first stage of clinical assessment. The diagnostic laboratory acquires various image data necessary for the development of medical equipment at the same level as that of the site of clinical diagnosis. The intelligent surgical operation room takes in real-time diagnostic images while a surgical operation is under way and, at the same time, assesses surgical devices in the same environment as that of the surgical operation room. The medical information laboratory accumulates medical and image data from the other laboratories, and integrates the accumulated data. The data management center manages the laboratories in a unified way and enables comprehensive assessment and research. (NEDO)

FY 2000 Project of developing international standards for supporting new industries. Standardization of the crushed, recycled CFRPs (carbon-fiber reinforced plastics); 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Recycle CFRP (tanso sen'i kyoka plastic) funsaihin no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the FY 2000 results of development of the basic technologies for, e.g., recycling CFRPs by crushing/screening them and also recycling carbon fibers by removing the matrices; development of the methods of measuring characteristics of the recycled stock materials; and standardization of the specifications, for proposing the international standards. The program for methods of crushing CFRPs tests the cylindrical CFRP samples (thickness: approximately 7mm) composed of high-strength carbon fibers and epoxy resin, to confirm feasibility of crushing by a shear type crusher. The program for removing the CFRP matrices studies epoxy resin as the representative thermosetting resin matrix material, to confirm that the matrix can be removed basically without greatly deteriorating strength of the carbon fibers by selecting an adequate catalyst and treating conditions. The program for studying the international standards finds neither international standard dedicated only for recycling CFRPs nor movement for establishing them. (NEDO)

Project in fiscal 2000 of developing international standards for supporting new industries. Comprehensive surveys and researches in relation with promotion of international standardization; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kokusai hyojunka suishin ni kakawaru sogo chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective of promoting the international standardization efficiently and strategically, surveys were performed on trends of international standardization in Europe and America, and researches on means for the international standardization. The standards strategy in the U.S. is to increase the U.S. competitive power in overseas countries, support strongly the domestic markets, and at the same time, deal with problems such as those of the environment. It attempts to structure a framework that can be utilized by any concerned parties, including business entities, the government, and consumers, whereas the National Standards Strategy (NSS) has proposed the initiative. In Europe, targeting to establish international standards originated from Europe, works are becoming more active for new technologies such as information communicating technologies from the R and D phase to the test and evaluation methods, taking the standardization into consideration. These works are being carried out within the scope of the common EU R and D, represented by the 'Framework program' and the 'EUREKA program'. In the survey and research on means to complete the international standardization, analyses and surveys were performed on the latest information, such as TC/SC, which are scheduled of proposition. Advices were given on giving the directionality and establishing the strategy. (NEDO)

Research and development of technologies for CO{sub 2} fixation and effective utilization thereof, etc., in fiscal 1998. Report on research and development of technologies for the effective use of CO{sub 2} by virtue of contact hydrogenation (CO{sub 2} separation and recovery system of the next-generation type); 1998 nendo nisanka tanso koteika yuko riyo gijutsu nado kenkyu kaihatsu jigyo. Sesshoku suisoka hanno riyo nisanka tanso yuko riyo gijutsu kenkyu kaihatsu jigyo kenkyu kaihatsu jigyo (jisedaigata shoene CO{sub 2} bunri kaishu system ni kansuru chosa kenkyu hokokusho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Researches were conducted for the goal of proposing a totally new process enhanced in efficiency and energy saving, and capable of CO2 separation. In fiscal 1997, hydrocarbon materials were reformed by oxygen separated within a system allowing fuel cells to generate power efficiently, when all the emitted CO2 was separated and recovered within the system. Furthermore, cold heat was utilized for the acquisition of liquefied CO2 gas products. A part of oxygen separated at the fuel cell cathode was recycled into the combustion section external to the tubular reaction reformer, and CO2 was separated by mere cooling from the combustion products for the simultaneous production of by-products such as high-purity nitrogen gas and liquefied CO2 for a great improvement in economy. In fiscal 1998, the system was improved. Proposed then was a new system in which an oxygen partial oxidation type reformer assumed the nuclear role, separating all the oxygen at the cathode, reusing part thereof for oxygen enrichment, and feeding the rest thereof into the reformer. The design realized the recycling of the whole of the products of the two cell electrodes into the reformer for the maximum reuse of the products of the hydrogen/oxygen separation function. (NEDO)

Joint verification project on environmentally friendly coal utilization systems. Joint verification project on the water-saving coal preparation system; Kankyo chowagata sekitan riyo system kyodo jissho jigyo. Shosuigata sentan system kyodo jissho jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-09-01

In this verification project, clean technology which should be spread in China was verified and the base structure for its spread was prepared for the purpose of controlling emissions of environmental pollutants associated with the coal utilization in China and of contributing to secure energy acquisition of Japan. As joint verification projects, a general rehabilitation type coal preparation system was installed in the Wangfenggang coal preparation plant, and a central control coal preparation system was installed in the Qingtan coal preparation plant. In the former, a system is verified in which optimum operation, water-saving, high quality, and heightening of efficiency can be obtained by introducing two computing systems for operation control and quality control, various measuring instruments, and analyzers to coal preparation plants where analog operation is conducted helped by Russia and Porland and have problems about quality control. In the latter, a central control system achieving water saving is verified by introducing rapid ash meters, scales, desitometers and computers to coal preparation plants having zigzag or heavy-fluid cyclon and connecting various kinds of information through network. For fiscal 1994, investigation and study were conducted. 51 figs., 9 tabs.

FY 1999 report on the potential survey of the environmentally friendly type coal utilization system - Dispatch of engineers. A. Project for supporting the introduction of the environmentally friendly type coal utilization system (model project)/pre-survey for the potential survey; 1999 nendo kankyo chowa gata sekitan riyo system kanosei chosa. Senmomka haken A. kankyo chowa gata sekitan riyo system donyu shien jigyo (model jigyo) - Kanosei chosa no jizen chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of the improvement of coal utilization technology and environmental preservation, the paper conducted the pre-survey of the introduction of coke oven gas desulfurization facilities in China and pre-survey of potentiality of the environmentally friendly type coal utilization system in India. The pre-survey in China was made for Anyang Steel Group Co. Ltd. and Laiwu Steel Group Co. Ltd. to judge their adaptability as site for the demonstrative project on the introduction of coke oven gas desulfurization facilities. As a result, it was confirmed that the former satisfied the conditions on Japan side such as the space for installation and prospect for fund raising. However, the amount of COG treatment was larger than that planned at Japan side, and it was found that as to the recovered sulfur, the company wanted the solid sulfur different from the fused sulfur planned at Japan side. In the survey in India, explanations were made to India of CFBC and the fluidized bed cement sintering system, bio-briquette production facilities, facilities for environmental measures, coal reforming technology, etc. At the same time, the site survey was made to examine/analyze possibilities of spread/development of Japan's CCT. (NEDO)

Fiscal 1998 intellectual infrastructure project utilizing civil sector functions. Research and development project on prompt-effect type intellectual infrastructure creation (Research and development concerning relations between sintered body textural structure and material characteristics in fine ceramics); 1998 nendo minkan no kino wo katsuyoshita chiteki kiban jigyo seika hokokusho. Sokkogata chiteki kiban sosei kenkyu kaihatsu jigyo (fine ceramics no shoketsutai soshiki kozo to zairyo tokusei tono kankei ni kansuru kenkyu kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Research and development was carried out involving fine ceramic sintered body textural structure evaluation methods for the development of process technologies for achieving higher quality and lower cost. Studies centered about a method for evaluating coarse pores and coarse grains in sintered bodies, relations between sintered body fracture strength and textural structure, and the standardization of evaluation methods. As the result, an evaluation method for observing pore structures in a sintered body flake specimen under an optical microscope and another for observing coarse grains under a polarization microscope were proposed. As for the effect of coarse defects on the fracture strength of ceramics, it was demonstrated experimentally and theoretically that coarse defects several tens of micrometers in size greatly affected the fracture strength. In the study of methods for sintered body grain size evaluation, findings were obtained about the processing of the specimen surface. (NEDO)

FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy field. Third year report. Development of precision farming system combined with the autonomous vehicle for large scale agriculture; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy bun'ya. Daikibo nogyo muke seimitsu jiritsu soko sagyo shien system no kenkyu kaihatsu (dai 3 nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A farming supporting system that enables autonomous driving was developed from a viewpoint that the development of super manpower saving technology including automation helps sustainable development of the Japanese agriculture. The following were conducted: development of autonomous driving vehicle, development of automated operation unit, field space mapping for precision agriculture and development of groups of PF (precision farming) work machine (weeder, controller, fertilizer applicator, harvesting machine), development of groups of field work sensor (simple soil analytical system, crop growing sensor, glass yield sensor), development of field information managing database, development of work optimized application software. The operation test on the integration system was made at the model production field. The operation experiment using fertilizer applicator, controller and autonomous driving tractor was carried out at a beet field of 2ha in the farming zone in Tokachi, Hokkaido, and the results were obtained as expected. Further, as to the precision agriculture introduced with developmental equipment, etc., 20% of the energy consumption is expected to be reduced. (NEDO)

FY 2000 report on the results of the regional consortium R and D project - Regional consortium R and D. Second year report. R and D of a high functional mini production system for small precision machine parts; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki cosortium kenkyu kaihatsu. Kogata seimitsu kikai buhin'yo kokino mini seisan system no kaihatsu kenkyu (dai 2 nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Judging that it is the most desirable to use processing systems suitable for product sizes from viewpoints of resource conservation, space saving and energy conservation, the development was proceeded with of machine tools for small precision machine parts (mini production cell). The size of cell is 200x200x200mm, and the working accuracy of the same level as that of the existing machine was targeted. Studies were made in the following 6 fields: 1) development of a total system; 2) design/manufacture/evaluation of mini cell; 3) evaluation of grinding processing cell (first phase) and accuracy control technology; 4) development of small sensor; 5) analysis/evaluation of element cell; 6) study on the basement technology of mini production system. In 2), study was divided into the following: development of grinding processing cell; development of grinding processing cell (second phase); processing performance test; structural analysis. In 6), study was divided into the following: outline of the study; study on micro plasticity processing; study on active type control of the removal amount; robust process design of mini production system. (NEDO)

FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy field. First year report. Development of the process for creation of new functional materials using electron beam excited plasma; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy bun'ya. Denshi beam reiki plasma wo mochiita shinkino zairyo sosei process no kaihatsu (dai 1 nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The development of manufacturing technology was proceeded with for a high speed nitriding system using electron beam excited plasma device which realizes high dissociation for nitrogen molecules and controls the plasma state. By the device, the following are aimed at: high quality/high speed nitriding, formation of super-hard cubic system boron nitride (c-BN) and carbon nitride (CN) films on the surface of tools, and formation of TiO{sub 2} thin films with high infrared reflectance and environmental purification photocatalyst function. TiO{sub 2} thin films are assumed to be applied to window glass by making use of the high performance heat mirror function as well as the environmental purification function. Studies were made in the following 6 fields: 1)development of small electron beam excitation plasma source; 2) development of high speed nitrided container; 3) establishment of technology for real-time monitoring of radicals and ions; 4) design/trial manufacture of a device to form super-hard nitrided thin films; 5) development of heat mirror film formation device; 6) establishment of a method to evaluate effects of photocatalyst. (NEDO)

FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D. Third year report. R and D of high grade/low cost mold for rubber/plastic; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu. Gomu plastic yo kohin'i tei cost kanagata no kenkyu kaihatsu (dai 3 nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-05-01

The development was proceeded with of technology to reform the surface of rubber/plastic use mold by ion engineering technology so that the product can be easily taken out without being stained by the material. Concretely, PBII (plasma-based ion implantation) device with high ion implantation efficiency was developed, and surface reforming conditions were studied. Then, from the test using the actual device, the surface reforming technology optimum to mold releasing and mold staining resistance as rubber molding was established. Studies were made of the following: 1) establishment of the optimum mold surface reforming technology; 2) establishment of the mold surface treatment technology using PBII device; 3) improvement of PBII device and optimization of implantation method. In 2), by the surface treatment by implanting nitrogen and fluorine ions into hard chromium plating and aluminum alloys using PBII device, treatment effects were recognized in implantation ability into 3D shape, mold staining resistance and mold releasing in the hard chromium plating treated mold. (NEDO)

FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy. First year report. Development of a next generation biopolymer information measuring system based on the nano channel electrophoresis; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy. Nano channel denki eido ni motozuku jisedai seitai kobunshi joho keisoku system no kaihatsu (dai 1 nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

On the basis of the nano channel electrophoresis technology, the construction was proceeded with of a system which integrates the basic process such as reaction, separation and detection needed for measuring biopolymer information and analyzes a number of samples simultaneously and with high accuracy/high sensitivity. Studies were made in the following three fields: 1) development of the basement technology on extraction/amplification/separation/detection of biopolymer; 2) development of micro-processing technology and system design and study on the development of device; 3) comprehensive investigational study. In 1), developmental technology is divided into the following: technology to effectively fraction/refine biopolymer from biological samples, technology for recognition control and manipulation of biopolymer, technology of amplification use micro-reaction of biopolymer, multiple selection technology of biopolymer using the specific molecular recognition, and technology for ultra-high speed separation of biopolymer. As to the multiple selection technology, DNA terminal recognizing hemin is altered by thiol group and connected to the surface of electrode to make an electrode type hemin recognition device. (NEDO)

FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy field. Third year report. Development of precision farming system combined with the autonomous vehicle for large scale agriculture; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy bun'ya. Daikibo nogyo muke seimitsu jiritsu soko sagyo shien system no kenkyu kaihatsu (dai 3 nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A farming supporting system that enables autonomous driving was developed from a viewpoint that the development of super manpower saving technology including automation helps sustainable development of the Japanese agriculture. The following were conducted: development of autonomous driving vehicle, development of automated operation unit, field space mapping for precision agriculture and development of groups of PF (precision farming) work machine (weeder, controller, fertilizer applicator, harvesting machine), development of groups of field work sensor (simple soil analytical system, crop growing sensor, glass yield sensor), development of field information managing database, development of work optimized application software. The operation test on the integration system was made at the model production field. The operation experiment using fertilizer applicator, controller and autonomous driving tractor was carried out at a beet field of 2ha in the farming zone in Tokachi, Hokkaido, and the results were obtained as expected. Further, as to the precision agriculture introduced with developmental equipment, etc., 20% of the energy consumption is expected to be reduced. (NEDO)

FY 2000 report on the results of the regional consortium R and D project - Regional consortium field. Third year report. R and D of the manufacturing technology of hybrid type biocompatible hard tissue substituting materials; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium bun'ya. Hybrid gata seitai yugo kinosei kososhiki daitai sozai seizo gijutsu no kenkyu kaihatsu (dai 3 nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

As instrument materials substituting for hard tissue such as tooth root and artificial hip joint, the technology development is being proceeded with of the use of high-biocompatible {beta} Ti alloys coated by hydroxy apatite. Studies were made in the following 6 fields: 1) design of high-biocompatible {beta} Ti alloys, system control and dynamic evaluation; 2) development of high efficiency calcium phosphate ceramics (hydroxy apatite) and development of surface coating technology; 3) development of melting casting technology of high-biocompatible {beta} Ti alloys; 4) biological evaluation of biocompatibility of high-biocompatible {beta} Ti alloys and completion of dental precision casting technology; 5) basic research on affinity of low rigidity Ti alloys (trial manufacture); 6) development of technology of precision processing and precision finishing processing of alloys. In 5), in the test on affinity of the trial-manufactured alloys, stainless steel and existing Ti alloys, it was verified that the trial-manufactured alloys were excellent in affinity. (NEDO)

FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D field. First year report. R and D of distributed power conditioner for photovoltaic power generation use; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu bun'ya. Taiyoko hatsuden'yo bunsangata power conditioner no kenkyu kaihatsu (dai 1 nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

By developing 100W class micro-inverter and putting it to the solar cell panel one by one, a control system is developed by which the maximum output can be obtained as the solar cell system even if the output of individual panels changes by stain and shade. By this system, power generation efficiency is expected to be increased by approximately 10%. In case that power generation of 5 million kW is achieved in FY 2010, energy conservation of about 50,000 kl/year in oil conversion can be expected. In FY 2000, the following were carried out: 1) investigational study of electronic parts; 2) primary trial-fabrication of micro-inverter; 3) various kinds of simulation assuming the inverter parallel operation. In 1), two kinds using the fly-back transformer method and the immittance conversion theory were trial-fabricated. As to the former, the main circuit method was designed to be the fly back type high frequency insulation method, and the control method to be the pulse area modulation method. As to the latter, the current output type power converter was structured by the circuit simulation. (NEDO)

Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium energy field/R and D of new technology using low temperature energy for storage of agricultural products (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium energy bun`ya / teion energy wo riyoshita nosanbutsu no shinki chozo gijutsu no kenkyu kaihatsu (daiichi nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The development was conducted of a new technology using low temperature energy in Hokkaido for storage of agricultural products. In this fiscal year, the R and D were conducted of 1) elucidation of behavior of water droplets in the air at below-freezing temperatures and technology to preserve agricultural products, 2) low temperature region high efficiency energy conversion application technology, and 3) latent heat cold storage technology. In 1), it was clarified that the electrostatic capacity system is appropriate as non-contact simple measuring device of moisture distribution in cold air. Freezing temperatures were measured of potatoes, onions and carrots produced in Hokkaido. Equipment to generate moist air at below-freezing temperatures was trially manufactured which is composed of humidifier and freezer. A relation was studied between the humidifying method and the size of particulate water droplet. In 2), an experimental device was trially fabricated of BiTe thermoelectric conversion device. An experimental device for Stirling engine power generation was assembled which was incorporated into the waste incinerator. A basic experimental device of pulse pipe refrigerator was trially fabricated. Single crystals of BiSb semiconductors were made. In 3), it was clarified that gas hydrates of CO2 and C3H8 are promising as refrigerant. 60 refs., 120 figs., 19 tabs.

FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D field. First year report. R and D of distributed power conditioner for photovoltaic power generation use; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu bun'ya. Taiyoko hatsuden'yo bunsangata power conditioner no kenkyu kaihatsu (dai 1 nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

By developing 100W class micro-inverter and putting it to the solar cell panel one by one, a control system is developed by which the maximum output can be obtained as the solar cell system even if the output of individual panels changes by stain and shade. By this system, power generation efficiency is expected to be increased by approximately 10%. In case that power generation of 5 million kW is achieved in FY 2010, energy conservation of about 50,000 kl/year in oil conversion can be expected. In FY 2000, the following were carried out: 1) investigational study of electronic parts; 2) primary trial-fabrication of micro-inverter; 3) various kinds of simulation assuming the inverter parallel operation. In 1), two kinds using the fly-back transformer method and the immittance conversion theory were trial-fabricated. As to the former, the main circuit method was designed to be the fly back type high frequency insulation method, and the control method to be the pulse area modulation method. As to the latter, the current output type power converter was structured by the circuit simulation. (NEDO)

FY 2000 Research and development project for creation of the standards. Standardization of information-providing technologies for establishing human/machine interfaces; 2000 nendo kijun sosei kenkyu kaihatsu jigyo seika hokokusho. Hito to kikai no interface kochiku no tame no joho teikyo gijutsu ni kansuru hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This survey/test/research project is aimed at standardization of providing information smoothly while securing safety for various types of drivers by introducing advanced technologies into vehicles.The methods of evaluating priorities of 105 items of information for drivers, which are taken up by ISO, are followed to find that 5.90, 2.05 and 0.11 items are selected for the alarm, route guiding and general information systems, respectively. These results are in agreement with the related literature survey results. The test results of the visual/auditory displays corresponding to the priority information types indicate that the adequate alarm displays are 'red/50nt/0.2 seconds, 30% frequency/6.0 degrees' for the visual sensation, and '80dB/2.0KHz+1.5 harmonics/0.2 seconds, 70% frequency' for the auditory sensation. The study on information volume and information recognizing time indicates that the symbol pattern is better than the letter pattern for the simultaneous display of up to 2 items learned beforehand. The others studied include alarm designs and management of two or more alarms. (NEDO)

Report on survey for high-performance industrial furnace introduction field test project in fiscal 1999. Activities to promote proliferation of the introduction to subject project related business entities; 1999 nendo koseino kogyoro donyu field test jigyo chosa hokokusho. Taisho jigyosha eno fukyu sokushin katsudo

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This paper reports the survey on high-performance industrial furnace introduction field test project in fiscal 1999. The development of a high-performance industrial furnace having been performed by NEDO since fiscal 1993 has completed the fundamental development research in fiscal 1998, and the planned achievements were verified (large energy saving, reduction of NOx emission, and down-sizing). Upon the result, the introduction field test project has started in fiscal 1998 for three years until fiscal 2000. The number of research items adopted in fiscal 1998 was 58, and those in fiscal 1999 was 51, which are progressing smoothly at the present. Reduction in CO2 emission of 50,000 tons was demonstrated as the achievement in fiscal 1998, and NOx emission realized the regulation value or lower in cities wherein each operator is executing the project. Several cases of down-sizing were also reported. In the proliferation promoting project in fiscal 1998, activities were made mainly to the subject project related business entities in relation with the development achievements and general technologies for the high-performance furnace. In fiscal 1999, communication transmission was continued by using information tools on introduction of the achievements and technologies. Attempts will be made on promoting the proliferation of the field test project in the future through a number of technology lecture meetings performed by specialists. (NEDO)

FY 1999 project on the development of new industry support type international standards. Standardization of a method to calculate recycling rates of automobile products; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Jidosha seihin no recycle ritsu no santei hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose not only of solving the environmental problem but also of making effective use of resources and contributing to the appropriate treatment in the stage of the used resource, study was conducted of the standardization of a method to calculate recycle rates of automobile products. The FY 1999 results were summarized. In this fiscal year, to give definition of the recycle potentiality and thermal recycle, the following were proceeded with: trial evaluation of recycle potentiality, survey of the actual state of recycling of rubber/plastic parts, study of the requirements to realize the recycle potentiality, study of the requirements to realize the thermal recycle, and approaches to the international standardization. As to the trial evaluation of the recycle potentiality, tests to dismantle automobiles were made to assess the dismantlement, separation and recognition. The requirements to realize the recycle potentiality were studied. It was found out that few non-metallic materials are not recycled in the present situation. The paper studied what the requirements to realize the recycle potentiality and thermal recycle should be like basically since there is no recognition internationally unified. (NEDO)

FY 1999 project on the development of new industry support type international standards. Standardization of evaluation method of the genetic testing system (Separate volume); 1999 nendo shinki sangyo shiengata kokusai hyojunka kaihatsu jigyo seika hokokusho. Idenshi kensa system no hyoka hoho no hyojunka (bessatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The separate volume included the proceedings of the re-consignee joint meeting on the standardization of evaluation method of the genetic testing system, the proceedings/data of the meeting of the committee of the standardization of evaluation method of the genetic testing system, etc. The data of the meeting are about a plan to execute the standardization of evaluation method of the genetic testing system, standardization of forms for reporting the results of the genetic test, a trial guideline for standardization of the genetic testing, standardization of evaluation method of the genetic testing system, etc. Moreover, the volume included 11 literature papers overseas on the above-mentioned themes, 'reports on the surveys in Europe and the U.S. on the standardization of evaluation method of the genetic testing system,' etc. (NEDO)

Achievement report for fiscal 1999 (edition B) on auxiliary New Sunshine Project. Development of coal hydrogasification technology (Research by using experimental device); 1999 nendo New Sunshine keikaku hojo jigyo seika hokokusho (B ban). Sekitan suiso tenka gaska gijutsu kaihatsu - Jikken sochi ni yoru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective of using practically the coal hydrogasification technology (the ARCH process), developmental research has been performed on important elementary technologies using different experimental devices. This paper summarizes the achievements in fiscal 1999. In the research by using a small testing apparatus, the Taiheiyo coal was used to have performed demonstration operation on the replacement natural maximized case, the heat efficiency maximized case, and the BTX maximized case. As a result, the three cases were found nearly as anticipated in the simulation, whereas the replacement natural gas maximized case has achieved the targeted whole coal conversion rate of 60% or more. However, the BTX maximized case presented a value lower than the targeted BTX yield of 12%. In the developmental research on the injector, the injector having been fabricated for the hot model test was given another combustion test, where the focal temperature of 1,200 degree C or higher was derived. The hot model test has verified the non-agglomeration performance of coal by using as parameters the focal temperatures, coal cross sectional area loads, coal types, and injectors. It was verified that the Taiheiyo and Shin Mu coals do not agglomerate excessively. (NEDO)

Fiscal 2000 regional consortium research and development project - regional new technology creation research and development. Development of bio-recycling technology for bio-wastes; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki shingijutsu soshutsu kenkyu kaihatsu seika hokokusho. Seibutsukei haikibutsu no bio recycle gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are exerted to develop a closed brewing system for 'shochu (a Japanese distilled liquor)' and vinegar and a non-combustion type thermal recycling system based on the methane fermentation of farm animal's excretion and sludge. Activities are conducted in the three fields of (1) the development of a zero emission shochu and vinegar brewing process, (2) development of a non-combustion type thermal recycling method, and (3) a commercialization plan. Studied in field (1) are the brewing of 'shochu' by a new process (kaeshi-shikomi), preparation of vinegar out of the lees of 'shochu' brewing, evaluation of the physiological activity of vinegar and 'shochu' lees, cost efficiency evaluation of zero emission 'shochu' and vinegar brewing processes, and the like. In field (2), the methane fermentation conditions for garbage, sludge, and farm animals' excretion are studied, and a non-combustion type thermal recycling process and the like are evaluated for cost efficiency. In field (3), marketability is studied for vinegar made by fermentation, actualities of the recycling of bio-wastes and energy recovery therefrom are examined, and marketability is studied for regional distributed power generation. (NEDO)

Fiscal 1999 technical research report. Development project on prompt-effect international standards for developing new industry (Comprehensive survey and research concerning promotion of international standardization); 1999 nendo shinki sangyo ikusei sokkogata kokusai hyojun kaihatsu jigyo seika hokokusho. Kokusai hyojunka suishin ni kakawaru sogo chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For encouraging the promotion of international standardization involving the six subjects of advanced technology taken up under the above-named project, wide-range investigations are conducted into measures for international standardization, the activities of international standardizing agencies and organizations, and the approaches of European and American business corporations to this issue. Technical literature and material are studied in Japan, and interviews are held overseas with responsible persons at organizations and corporations engaged in this task. At Standards Development Organization (SDO) of America, verification tests are under way for early development into international standards of technical standards it has so far developed independently. For the strategical utilization of intellectual property incorporated into its technical standards, SDO accepts that the best policy is to win approvals from patent proprietors at the early stage of standardization process by presenting them with conditions about patent implementation. In Europe and America, for the enhancement of their competitive power in the international theater, governments and civil sectors cooperate with each other for the establishment of international standards and, in business corporations, the management takes the initiative in coping with the issue with an understanding that there are business opportunities in international standardization. (NEDO)

Fiscal 1999 survey report on basic feasibility concerning model project for energy conservation in fiber dyeing and processing industry in Thailand; 1999 nendo Tai ni okeru sen'i senshoku kako sangyo no sho energy ka model jigyo ni kakawaru kihonteki jisshi kanosei chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A feasibility study was conducted for the implementation of the optimum model project in the fiber dyeing and processing industry in Thailand. This paper describes the results of fiscal 1999. Seventy percent of about 400 companies are those heavily consuming energy, while small-scale businesses having a production capacity of less than one million yards/month take the sixty percent of the industry. Their energy conserving measures are behind. Measures against ground subsidence and drainage cost these companies greatly. Trade competition with China and others is being intensified. Although designated under the Energy Saving Promotion Act, the plants are not enjoying the privilege. Needed for the energy saving measures are grasp of the current situation such as energy consumption status, thorough operation management, improvement of energy efficiency in the present production facilities, renewal/additional installation of production equipment, and implementation of developmental energy saving measures. As energy conservation measures are deemed adaptable to the industry if the investment recovery period is two years or less, diagnostic analysis was made on six plants, with diffusion of the result examined. The total energy consumption of the industry was estimated to be reducible by 35% through high-recovery-rate measures such as improvement of boilers, recovery of exhaust heat, control of energy consumption rate, and introduction of dyeing machines having low liquor ratio. (NEDO)

FY 1999 project on the development of new industry support type international standards. Standardization of digital image processing in household digital electronic devices; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kateiyo digital denshi kiki ni okeru digital gazo shori no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

As a framework of the processing of intellectual properties concerning the mobile videophone use coding system, MPEG-4, the paper took up the Intellectual Property Management and Protection (IPMP) framework, discussed a proposal for the standardization aiming at expanding IPMP functions, and summed up the FY 1999 results. In the activities of MPEG-4PF project in this fiscal year, four of the tools from Japan were extracted as candidates of the powerful tool which belongs to 'Simple and Core' of MPEG-4Visual and profile of MPEG-4Audio, and the international standardization was promoted. Especially, attention was paid to the mobile, promotion was made as a tool effective for heightening error resistance, and all the proposals were adopted. Further, attention was paid to the security field, and a proposal was made for IPMP expansion. The expansion makes up defects of the IPMP system which had already been proposed as a candidate for standardization. For the intensive discussion for this, a special work team was set up, and a special meeting was held at Tokyo University. (NEDO)

FY 1999 project on the development of new industry support type international standards. Standardization of a production process system (development of STEP standards); 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Seisan process system no hyojunka (STEP kiban kikaku no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The R and D were carried out of the standards of assembly models in design-production process and machining process data models for production preparation, and the FY 1999 results were summarized. Integrated AAM is a reference model to make relations with AP clear, and therefore, study was made with much higher accuracy. As to resource models to express product models which make change in design possible, studied were measures for changes in shape/dimension of parts, measures for changes related to connection in assembly, etc. As to resource models required to express the process of changes from design models to production models, arrangement was made of characteristics of the shape of design models and characteristics of production process models, and study was made of models to express the seamless work from design to processing. Study was also made of the method of conversion among design models and production preparation models. The results obtained were reported as N830 and N448 of ISOTC184/SC4/WG3. (NEDO)

Fiscal 2000 survey report on rationalization project for international energy conservation. Preparation of master plan for rational energy consumption (Shanxi Province, China); 2000 nendo kokuasi energy shiyo gorika kiban seibi jigyo chosa hokokusho. Goriteki energy shiyo no tame no master plan sakusei (Chugoku Shanxi sho)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A comprehensive master plan for Shanxi Province was prepared jointly with China for the purpose of promoting rational use of energy and realizing an environmentally harmonious demand/supply structure of energy. This paper describes the fiscal 2000 results. The first phase refers to the surmounting of environmental problems incident to the use of coal and the restoration of regional economy. As countermeasures against air pollution in Taiyuan City, environmental measures were propagated such as simplified flue-gas desulfurization in thermal power plants, energy conservation in coke dry quenching, etc., and desulfurization of coke oven gas. Bio-briquette effective against smoke and soot pollution was carried out, as was general rubbish treatment (e.g., compost and coal/rubbish mixed combustion power generation). Promoted, by the opening of a clean coal center, were sulfur content reduction, coal briquette method, market expansion for CWM, etc. Producing city gas out of coal mine methane gas was also among the ideas considered. With the aim of attaining a Shanxi Province zero emission program, incentives are essential and, for this purpose, support by the national government is desirable including subsidies for investment, low-interest loans, tax deductions/exemptions, and yen-denominated loans from Japan. The second phase is intended for harmony with culture/science/nature, control of global warming and advanced utilization of coal. (NEDO)

Fiscal 2000 regional consortium research and development project - regional new technology creation research and development. Development of bio-recycling technology for bio-wastes; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki shingijutsu soshutsu kenkyu kaihatsu seika hokokusho. Seibutsukei haikibutsu no bio recycle gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are exerted to develop a closed brewing system for 'shochu (a Japanese distilled liquor)' and vinegar and a non-combustion type thermal recycling system based on the methane fermentation of farm animal's excretion and sludge. Activities are conducted in the three fields of (1) the development of a zero emission shochu and vinegar brewing process, (2) development of a non-combustion type thermal recycling method, and (3) a commercialization plan. Studied in field (1) are the brewing of 'shochu' by a new process (kaeshi-shikomi), preparation of vinegar out of the lees of 'shochu' brewing, evaluation of the physiological activity of vinegar and 'shochu' lees, cost efficiency evaluation of zero emission 'shochu' and vinegar brewing processes, and the like. In field (2), the methane fermentation conditions for garbage, sludge, and farm animals' excretion are studied, and a non-combustion type thermal recycling process and the like are evaluated for cost efficiency. In field (3), marketability is studied for vinegar made by fermentation, actualities of the recycling of bio-wastes and energy recovery therefrom are examined, and marketability is studied for regional distributed power generation. (NEDO)

Fiscal 1998 R and D project on industrial technology. Development report on use technology of bioresources such as bioconsortia (Development of analysis technology of bioconsortia); 1998 nendo sangyo gijutsu kenkyu kaihatsu jigyo. Fukugo seibutsukeinado seibutsu shigen riyo gijutsu kaihatsu (fukugo seibutsukei kaiseki gijutsu no kaihatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

For use of advanced functions of bioconsortia (complex microorganisms composed of more than 2 microorganisms with certain specific function), this project analyzes specific functions of specific organisms and the interaction between the specific functions, and develops isolation and incubation technologies of component organisms. In fiscal 1998, to promote this project, the meetings were held frequently in National Institute of Bioscience and human Technology. Study was made on production of useful substances and useful degradation functions in association with bioconsortia. The result showed that microorganisms coexisting with nematode produced physiologically active substances exhibiting antimicrobial activities to tubercle bacillus, MRSA and others, microorganisms coexisting in eggs of some insects produced substances having antiviral activities and activities against pathogenic bacteria in a plant, and microorganisms growing in some plants or mycorrhiza organisms produced insecticidal substances or growing-promoting substance. The basic understanding was obtained on cooperative actions of bioconsortia to bioremediation and degradation of organic substances. (NEDO)

Achievement report for fiscal 1999 on auxiliary New Sunshine Project. Development of coal hydrogasification technology (Survey and research on its social acceptability); 1999 nendo New Sunshine keikaku hojo jigyo seika hokokusho. Sekitan suiso tenka gaska gijutsu kaihatsu - Shakai tekigo sei ni kansuru chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to evaluate feasibility of practical use and economy of the coal hydrogasification technology (the ARCH process), survey and research have been performed. This paper summarizes the achievements in fiscal 1999. In the survey on the social acceptability, survey has been made on the future trend in the demand and supply and the price of LNG, LPG, and coal for hydrogasification. As a result, it was discovered that the price of LNG imported into Japan is determined as if linked with the crude oil price, and Saudi Arabia is the price leader of the LPG price. With respect to the survey on the possibility of international cooperation, surveys were conducted on the prospects of the long-term demand and supply in China, natural gas resources, and the demand and supply thereof. The feasibility study has estimated the product gas manufacturing cost after the process has been improved. In the trial calculation on the three-mode cost, it was discovered that, although the profit from byproducts is great, the BTX maximized mode causes the manufacturing cost to be higher by as much as 2 to 3 yen per Nm{sup 3} than that of other modes because of higher unit consumption in raw materials and higher construction cost. (NEDO)

FY 1999 project on the development of new industry support type international standards. Standardization of evaluation method of the genetic testing system (Separate volume); 1999 nendo shinki sangyo shiengata kokusai hyojunka kaihatsu jigyo seika hokokusho. Idenshi kensa system no hyoka hoho no hyojunka (bessatsu)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The separate volume included the proceedings of the re-consignee joint meeting on the standardization of evaluation method of the genetic testing system, the proceedings/data of the meeting of the committee of the standardization of evaluation method of the genetic testing system, etc. The data of the meeting are about a plan to execute the standardization of evaluation method of the genetic testing system, standardization of forms for reporting the results of the genetic test, a trial guideline for standardization of the genetic testing, standardization of evaluation method of the genetic testing system, etc. Moreover, the volume included 11 literature papers overseas on the above-mentioned themes, 'reports on the surveys in Europe and the U.S. on the standardization of evaluation method of the genetic testing system,' etc. (NEDO)

FY 2001 study report on the evaluation/analysis of the data collected in the field test project on the photovoltaic power generation for public facilities, etc.; 2001 nendo kenkyu seika hokokusho. Kokyo shisetsu you taiyoko hatsuden field test jigyo ni okeru shushu data hyoka kaiseki

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-03-01

As a field test project on the photovoltaic power generation, collection/analysis/evaluation of the operational data were made about photovoltaic power systems installed at 73 places in FY 2001. As to the analysis of deterioration with age and yearly changes of the system, analysis was made of operation hours of the equivalent system, system output coefficient and inverter performance efficiency in FY 1999, FY 2000 and FY 2001, and it was confirmed that there was few deterioration with age. Relating to the evaluation of reliability of the system, evaluation was made for the record of failures of photovoltaic power systems at 73 places, and the results were not very good as follows: average failure cycle: 1.06 y/system; average failure repair period: 14.9 d/system; rough opportunity loss electric energy: 81,548 kWh/y x 73 sites. Concerning the analysis of economical efficiency, the system cost decreased year by year to 1,102,000 yen/kW in FY 1997, and the power generation cost became 91.8 yen/kWh. The fund recovery year was 35.3 years, assuming the following: unit price of selling electricity: 15 yen/kWh, durable years: 20 years, and public subsidiary rate: 1/2. (NEDO)

Project in fiscal 2000 of developing international standards for supporting new industries. Standardization of method for evaluating characteristics measurement for micromachine materials; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Micro machine yo zairyo no tokusei keisoku hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Targeting the international standardization of the method for evaluating properties measurement for micro-machine materials, R and D has been performed on measurement and evaluation of mechanical properties of different thin film materials with a thickness of about 10 {mu}m or less and a width of 100 {mu}m or less. This paper summarizes the achievements in fiscal 2000. The current fiscal year has executed tensile tests of thin film materials for micro-machines, and surveys on technological trends related to the standardization thereof inside and outside the country. A working process was developed to manufacture test pieces of the thin film materials including mono-crystalline silicon for the purpose of executing the round robin test. Prototype test pieces were fabricated. The round robin test was performed by using these test pieces, wherein improvements were given on the test pieces, structure of the testing machine, the distortion measuring method, and the test piece mounting method. Furthermore, discussions were given on the film forming conditions and the heat treatment conditions with regard to mainly the thin titanium film made by using the sputtering process and thin nickel film made by using the plating process. The IEC/TC47/WG4 committee has announced to propose this evaluation technology as the future international standard. (NEDO)

FY 2000 Study report. Feasibility study on model project for effective utilization of sensible heat of off gas from hot stoves at blast furnaces in India; 2000 nendo Indo ni okeru koro netsufuro hai gas kennetsu yuko riyo model jigyo jisshi kanosei chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The feasibility study was conducted on a model project in India for the energy saving effect and reduction of the greenhouse gas emissions by introducing blast furnace hot stove waste heat recovery systems in steelworks. The blast furnaces studied are Blast Furnace G at Jamshedpur Steelworks of TISCO, the largest private steel maker in India, and No.7 Blast Furnace at Bhilai Steelworks of state-operated Steel Authority of India Ltd. (SAIL). The study results indicate that the annual energy-saving effects of 8,255 and 8,190 tons as heavy oil, and annual CO2 emission reduction of 25,543 and 25,342 tons are expected in the TISCO and SAIL blast furnaces, respectively, in the case of increasing blast temperature and reducing blast furnace fuel coke (increased iron production possible). The model project is applicable to both blast furnaces. There are a total of 46 blast furnaces in India in which the heat recovery systems can be introduced. The nation-wide annual energy saving and CO2 abatement would reach 126,202 tons as heavy oil and 390,501 tons, when all of these blast furnaces could be provided with the heat recovery systems. (NEDO)

Project in fiscal 2000 of developing international standards for supporting new industries. Standardization of communication interface for open robots in production system; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Seisan system nado ni okeru open robot yo tsushin interface no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

In order to realize the open use between robot controllers and personal computers on the communication level, R and D has been performed on the standard API required for structuring the applications to use robot information on the personal computers. A draft of the international standard was prepared. This paper summarizes the achievements in fiscal 2000. The current fiscal year has executed improvements on the standard API software, as well as the demonstration tests. The following achievements were obtained: problems in practical use based on the demonstration tests of RAO ver. 0.5 were extracted and rectified; the standard API (Ver0.9) given additional functions including file transfer was developed; the specifications for the standard API (Ver1.0) were compiled based on the result of discussions on the major application functions; as a result of the demonstration test on reliability of the standard API (Ver0.9), performances were verified when the API is connected under different structural and using conditions; and a resolution was made at the ISO/TC184/SC2 international conference that 'continuation is encouraged on the present R and D expected as a proposal for the new work items'. (NEDO)

Fiscal 2000 regional consortium research and development project - regional new technology creation research and development. Massive rapid identification of gene functions; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki shingijutsu soshutsu kenkyu kaihatsu seika hokokusho. Idenshi kino no tairyo jinsoku dotei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are exerted to develop a system for massive and rapid identification of unknown genes through the utilization of techniques based on the unusual membrane fusion characteristics of HVJ (hemagglutinating virus of Japan), which enables the introduction of genes efficiently and uniformly into cultured cells and living organs (development into a kit). Activities are conducted in the three fields of (1) the development of a method for introducing genes using an HVJ envelop vector, (2) a survey of kit marketing and cold storage facilities in the selling and distribution of the kit, and (3) a comprehensive survey. In the field of (1), studies are conducted for the establishment of methods for HVJ envelop vector production and refining, the establishment of an optimized method for encapsulating genes into the HVJ envelop vector, and the introduction of genes into cultured central neurons using the HVJ envelop vector system. A refining method has been established, which comprises the inoculation of HVJ into eggs, 4-day culture, egg cutting, liquid sampling (chorioallantoic liquid), inactivation (addition of alkylating agent), filtration, enrichment (ultrafiltration), and an anion exchange chromatogram. (NEDO)

Research cooperation promoting project in fiscal 1998. Research cooperation related to developing mine resources extraction and treatment technologies of environment harmonizing and high efficiency type; 1998 nendo kenkyu kyoryoku suishin jigyo. Kankyo chowagata kokoritsu kobutsu shigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In order to realize more effective utilization of non-ferrous metal resources, joint research cooperation is made with the Republic of Kazakhstan. It is intended that valuable metals (gold, silver, copper, rare metals, and others) contained at large quantity in ore scraps generated in association with mine operation be extracted and recovered efficiently paying considerations to the environment. The treatment process consists of the following conception: raw materials such as ore scraps are leached by sulfuric acid and microorganisms to separate and recover gold and silver; the leach liquor containing valuable metals is extracted by using solvent and recovered of copper and rare metals via an electrolytic process; and the waste water is treated and discharged. Fiscal 1998 has performed studies on the wet treatment system at the site and in Japan, the gold and silver treatment, and the waste water treatment by using samples collected from the site in fiscal 1996. Based on the results of these fundamental studies, a pilot plant was built, and all of the facility fabrication was completed in fiscal 1998. Part of the facilities has been transported to the site. To drive the project forward effectively, materials and items of equipment required for the joint research were procured and transported to the country, and at the same time Kazakhstanian researchers were received in Japan for training. (NEDO)

FY 1999 project on the development of new industry support type international standards. Standardization of a testing/evaluation method of biological use fine ceramics; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Seitaiyo fine ceramics no shiken hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of standardizing/international standardizing an evaluation method of the characteristics required for biological use fine ceramics, and the FY 1999 results were summed up. In the study of characteristics of biological use fine ceramic materials, it was confirmed that zirconia ceramics are more excellent than alumina ceramics in static strength, repeated loads and fatigue properties in the atmospheric air at room temperature. In the study of the evaluation method of biological affinity, the standardization of the simulated body liquid preparation process was studied, and the simulated body liquid was prepared. To evaluate the bioactivity of biological use fine ceramics without making animal experiments, the simulated body liquid in which the ion concentration was made exactly equal to that of human being was prepared using 2-hydroxyethyl-1-piperazinyl ethane sulfonic acid as buffer. There were seen no changes in ion concentration for four weeks at longest as long as this liquid is kept in airtight container at temperature of 36.5 degrees C or below. The present situation of the standardization of bioceramics was surveyed. (NEDO)

FY 1997 evaluation/analysis by site of the data collected in the field test project for photovoltaic power generation for public facilities. 3/3; Kokyo shisetsunadoyo taiyoko hatsuden field test jigyo ni okeru shushu data hyoka kaiseki kaku site betsu (1997 nendo). 3/3

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-07-01

The data were collected on field tests of the photovoltaic power generation. The items of measurement are horizontal insolation intensity, inclined insolation intensity, effective inclined insolation intensity, average temperature, array electric energy, system electric energy, load electric energy, system supply load, back flow electric energy, interconnected protective movement, disconnection hour, system operating hour, independent operation load, independent supply load, equivalent array operation, equivalent system operation, array output coefficient, system output coefficient, system utilization rate, system power generation efficiency, INV effective efficiency, INV load factor, etc. The number of places for measurement is 27 including the following: Environmental Science Research Institute, Utatsu-cho Municipal Office, Ginga-gakuin Junior High School, New Energy Business Coop, Nisshin Techno Center, Shikoku Medicom Co., Miyosawa Kinoko-en, Takasaki City Welfare Vocational School, Madama Junior High School, Hitoo Junior High School, Koshien-gakuin Junior/Senior High School, Sansei Technical Research Development Center, Mitsui Greenland, DHI Mach head office/plant, Nabeya Ueno Water Purification Plant, Hoo Senior High School, National Agricultural Resource Research Center, etc. (NEDO)

Fiscal 2000 project for development of international standards for supporting novel industries. Standardization for enhanced interoperability between optical disk systems; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Hikari disk system no sogo un'yosei kakuho no tame no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development was carried out for the enhancement of logical format-based interoperability between optical disk systems for the purpose of presenting propositions for international standards. That is, UDF (universal disk format) defined by OSTA (Optical Storage Technology Association) was taken up against the volume/file structure defined by ISO/IEC13346, and efforts were exerted to substantiate environments for its compatibility test and to develop specifications to achieve such enhanced interoperability. In this fiscal year, specifications were drafted for application program interfaces for the UDF-based file system and UDF security augmentation. These would be presented to IEC (International Electrotechnical Commission) and OSTA, respectively. Their Japanese versions were submitted to the Ministry of Economy, Trade and Industry of Japan, for publication as standard-related information. Maintenance of UAF (universal accessible file) system-compliance test tools were accomplished in response to user requirements and to the updating of UDF-compliance test disk specification. (NEDO)

Achievement report for fiscal 1998 (edition B) on auxiliary New Sunshine Project. Development of coal hydrogasification technology (Research by using experimental device); 1998 nendo New Sunshine keikaku hojo jigyo seika hokokusho (B ban). Sekitan suiso tenka gaska gijutsu kaihatsu - Jikken sochi ni yoru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

With an objective of using practically the coal hydrogasification technology (the ARCH process), developmental research has been performed on important elementary technologies using different experimental devices. This paper summarizes the achievements in fiscal 1998. In the research by using a small testing apparatus, the Taiheiyo coal was used to have derived hydrogasification data (distribution and yield of the reaction products) in case of having changed the reaction pressure, temperature rising rate, and H{sub 2}/caoal ratio, and to verify the possibility of increasing the BTX yield by installing a temperature zone in two steps. In the developmental research on the injector, a combustion test and a coal feeding test were performed on the injector having been designed and fabricated in the previous fiscal year to verify the basic performance and evaluate the heat resistance and durability. With respect to the hot model test, a test installation was completed with the injector mounted to conduct the trial operation and test. In addition, development was conducted on the coal temperature rise simulation as the second phase of developing the simulation of mixing of coal with high-temperature hydrogen and temperature rise. (NEDO)

Fiscal 1999 achievement report. Venture seed pickup type international cooperative research project (Development of ultrahigh-speed terabyte optical disk storage device); 1999 nendo venture seeds hakkutsugata kokusai kyodo kenkyu jigyo seika hokokusho - venture seeds No.7. Chokosoku terabyte hikari disk kioku sochi no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Efforts are made to submit a concrete, industrialization-capable proposition for a huge-volume high-rate data storage device to be connected directly to the optical fiber communication network. The terabyte optical disk storage device is based on the patented technologies owned by some organizations participating in the project, and embodies a 1-terabyte memory and a 1-Gbps data transfer rate in a CD-size disk with CD/DVD compatibility not affected. The road to a novel, huge-volume, ultrahigh-speed data storage device was open when the basic principle of collinear-polarization digital volume holography was successfully confirmed. A new optical disk medium was fabricated for recording digital volume holograms, and a success was attained in retrieving records on a terabyte optical disk evaluation system. A novel spatial light modulator was successfully fabricated using the magnetooptic effect. This will enable improvement on transfer rates in digital volume hologram retrieval devices and introduction of such devices into optical communication in the field of information technology. (NEDO)

FY 1998 evaluation/analysis by site of the data collected in the field test project for photovoltaic power generation for public facilities. 4/4; 1998 nendo kokyo shisetsu nadoyo taiyoko hatsuden field test jigyo ni okeru shushu data hyoka kaiseki kaku site betsu. 4/4

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

The data items are horizontal insolation intensity, inclined insolation intensity, effective inclined insolation intensity (each unit: kWh/m{sup 2}), average temperature, array power energy, system power energy, system consumption power, load power energy, system supply load, and back flow power energy (each unit: kWh). Besides, the number of interconnected protective movement, disconnection hour (minute), system operating hour (minute), independent operating load, independent supply load (each unit: kWh), equivalent array operating hour, equivalent system operating hour, array/system output coefficient, system utilization rate/power generation rate, INV effective efficiency, and INV load factor. The objects of field tests are government office (joint office building, etc.), school (college, high school, elementary school, etc.), the Shinkansen Kyoto Station, health/welfare facilities (health facilities for the elderly, welfare center, etc.), hospital, industrial experimental station, training facilities (exhibition training facilities, etc.), broadcasting facilities, etc. (NEDO)

Fiscal 2000 achievement report on the venture business assisting type regional consortium - Minor business creation base type. Development of touch panel display operated by micro-Peltier device; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Micro Peltier soshi ni yoru shokkaku display no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The project aims to develop a small, light, and inexpensive touch panel display that enables visually handicapped people to transmit information by use of their manual sensation. Information from computers or the like is exhibited on the display in arrays of hillocks and dents. For improvement on display resolution and for cost reduction, efforts are made (1) to employ micro-Peltier devices for the simplification of the hillock-dent display mechanism and for the realization of a high resolution tactile display and (2) to establish a technology for manufacturing low-cost micro-Peltier devices. In the tactile display to be developed, the hillocks and dents are formed using gas-filled tiny balloons. The balloons are 2-dimensionally arranged, with the gas therein to be expanded and contracted via micro-Peltier devices. Difference between hillock-dent arrays and changes therein with the passage of time provide information. The gas in the balloons is inflated and contracted through the operation of micro-Peltier devices. In concrete terms, efforts were made to develop (1) a prototype hillock-dent display, (2) a technology for manufacturing high-performance low-cost micro-Peltier devices, and (3) a software program for computers to drive tactile displays. (NEDO)

FY 1999 Report on the technical results. Research and development project for creation of the quick-effect type international standards (Standardization in the field of safety of machinery); 1999 nendo sokkogata kokusai hyojun sosei kenkyu kaihatsu jigyo seika hokokusho. Kikai anzensei ni kakawaru hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

It is necessary to standardize the concepts and terminology of safety, design principles, protection and technology for evaluation of safety over a wide range including designs and specifications, in order to secure safety of the users. The international standardization has been promoted, based on the European voluntary standards EN. It is necessary for Japan to propose the international standards reflecting the industrial environments of Japan, in order to keep and expand her international competitiveness. Those technologies developed for the above purposes include the safety-related ones based on the Japanese electronic technologies, electronized operation-controlling technologies with dynamic fail safe signal processing, DC power supply circuit with a failure-sensing circuit, opto-ultrasonic hybrid type personal sensing device and pressure-sensitive mat sensor, emergency stop devices having no electrical contact to eliminate the contact fusing risk, and video camera system which facilitates emergency stop action of machinery. These results are submitted to the related technical committees of ISO or IEC. A total of 46 items of the international standard proposal drafts related to IEC/TC44 are also submitted. (NEDO)

FY 1999 project on the development of new industry support type international standards. Standardization for high-interoperability of optical disk systems; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Hikari disk system no sogo un'yosei kakuho no tame no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The R and D were conducted on the standardization for interoperability of optical disk system, and the FY 1999 results were summarized. In the study, for the volume/file structure specified by ISO/IEC 13346, the development of standards was made for interoperation of the UDF specified by OSTA. In this fiscal year, to avoid the problem on non-interchangeability of UDF which actually exists, enhancement of functions of a test tool for UDF interchangeability was tried. Namely, development was carried out of UDF interchangeability test tool, UAF related standards, and UAF related standards assessment system. Especially, it was formally announced that UDF security enhancement of UAF related standards will be included in UDF2.x in the OSTA conference held at the end of FY 1999. Also, a draft on the standard information was drawn up domestically. The standards including API are expected to be established as standards through activities in the next fiscal year. (NEDO)

Fiscal 2000 achievement report on project for research and development of intelligent infrastructure creation and utilization technologies. Research and development of reference materials for polymers; 2000 nendo chiteki kiban sose riyo gijutsu kenkyu kaihatsu jigyo seika hokokusho. Kobunshi ni kansuru hyojun busshitsu no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

As one of the efforts to establish national reference materials at an accelerated pace in a concentrated manner, a comprehensive survey was conducted on reference materials for polymers, and research and research was conducted for the development of such. In the comprehensive survey, investigations were made into the actual use of reference materials for polymers and their management at private-sector enterprises and public research institutes in Japan and at research bodies in the U.S. and Canada. In the development of reference materials for polymers, a procedure was contrived for synthesizing monodisperse oligostyrene specimens, polymerization was carried out using an improved synthetic method, and molecular weight distribution was analyzed. Using a homogeneous oligostyrene reference material for calibration, the mean molecular weight of an oligostyrene reference material was accurately evaluated by size-excluded chromatography. In the case of a specimen with its mean molecular weight not more than 1,000, the result exhibited excellent agreement with what supercritical fluid chromatography indicated. In the development of reference materials for characteristics evaluation, this in relation to methods for evaluating thermomechanical characteristics of plastics, efforts were made to develop reference materials for evaluating dynamic viscosity/elasticity of solid plastics. (NEDO)

Fiscal 1999 technical research report. Research and development project on prompt-effect international standards creation (Standardization of gene amplification and analysis methods for genetic screening); 1999 nendo shinki sangyo ikusei sokkogata kokusai hyojunka kaihatsu jigyo seika hokokusho. Idenshi kensayo idenshi zofuku kaiseki hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the promotion of Japan's proposition for international standardization, PCR (polymerase chain reaction) Comprehensive Research Committee, Technical Promotion Committee, and Japan Bioindustry Association organized a 5-member overseas research team and dispatched the team to Europe and America where they held research interviews at government organizations and business corporations engaged in standardization promotion. The aims were to disclose trends of PCR method standardization and standardization in general in biotechnology. The team visited British Standards Institution, Association Francaise de Normalisation, German Institute for Standardization, Food and Drug Administration of America, American Society for Testing and Materials, PE Biosystem, Bio-Rad Laboratories, and Roche Molecular Systems. The objects of standardization at issue included techniques, tools, devices, and reagents to be used. It is found that in Europe and America there are standardization plans under deliberation for PCR-aided techniques, not for PCR itself, and that some are now approaching completion as national or local standards. It is also learned that in every standardizing organization there is a person responsible for each TC (technical committee) of CEN (Committee European pour Normalisation). (NEDO)

FY 1999 project on the development of new industry support type international standards. Standards development of chemical analysis and non-destructive inspection methods for pure titanium metals; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Junchitan no shiken hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

To propose it to ISOTC79 and ISOTC135, study was conducted for standardization of chemical analysis method and non-destructive inspection method for industrial use pure titanium. As the chemical analysis method, the inductively coupled plasma atomic emission spectrometry which has good detection limit was developed, and at the same time, the standardization of spark and/or glow discharged atomic emission spectrometry was developed. As the non-destructive inspection method, developmental study on the following was carried out: surface defect inspection method of pure titanium metals by laser scanning inspection system or CCD camera; internal defect inspection of pure titanium sheet and coil by plate wave ultrasonic inspection method; internal defect inspection of pure titanium bar by eddy current method; inspection of very small leakage of pressurized fluid through defects in pure titanium pipe and tube by pressure differential testing method. As a result of the study, standards of system performance and tolerance were determined in analysis of Pd, Si, Al, Cu, Mo, Zr, Nb, Ta and Y. Further, analytical conditions and application ranges of the spark discharged atomic emission spectrometry were made definite in terms of 19 elements including Mn, Fe, Ni, Cr, Sn, Pb, Si, Al, V, Cu, Mo, Zr, Nb, Ta, Co, B, Y, C and W. (NEDO)

Research report for fiscal 1998 on the basic research for energy consumption efficiency improvement in developing countries. Joint research for oil consumption efficiency improvement. Indonesia; 1998 nendo hatten tojokoku energy shohi koritsuka kiso chosa nado jigyo sekiyu shohi koritsuka kyoryoku chosa jigyochosa hokokusho. Indonesia

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

On-site researches are conducted to study the possibility of a model business using energy-saving and environment preservation technologies of Japan and Indonesia. At textile plants, the management of heat and water in the dyeing and finishing processes is found inadequate, with great quantities of heat left uncared-for in medium- and low-temperature wastewater. An energy-saving proposition is submitted in which solar energy and absorption-type refrigerators are combined. Instrumentation and management also require improvement. At nitrogenous and phosphatic fertilizer plants, the energy consumption rate is found aggravated by degradation of facilities, and continued research and further analysis are necessary before working out energy-saving policies for them. At urea fertilizer plants, though it is not easy to modernize the manufacturing processes, energy-saving and environment preserving efforts are under way within the bounds of capability. Their energy consumption rate is high because of frequent shut-downs. It is necessary to detect an anomaly at its early stage and to introduce backup systems for the elimination of erroneous operations. Operating conditions need to be analyzed for validity. At melamine manufacturing plants, process drainage is allowed into the river without any treatment contaminating the water with products of melamine hydrolysis. Short-term and long-term solutions are suggested. (NEDO)

Fiscal 2000 achievement report on the venture business assisting type regional consortium - Minor business creation base type. Commercialization of human monoclonal antibody as investigational reagent; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Hitogata monoclonal kotai no kenkyuyo shiyaku to shite no seihinka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Technical seeds of in vitro immunization technologies for human peripheral lymphocytes and technologies for human cell fusion, both developed by Kita-Kyushu National College of Technology, are used, and human monoclonal antibodies are prepared easy to connect to tumor markers, allergens, and microbes. The project aims further to develop a technology for small-scale high-density production of such antibodies and to supply them as human monoclonal antibody reagents meeting the needs of bio-researchers in the fields of medicine, pharmacy, biology, agriculture, or the like. A human fusion partner cell strain SK-729-1 clone is obtained, which is high in ability to produce antibodies. Since the obtained cell is culturable in a serumless medium, a fusion cell strain prepared using the said cell strain is also culturable in a serumless medium. Hence: advanced refining now available for human monoclonal antibodies. Nine types of antibodies are acquired. Furthermore, it is made possible to predict the antibody reaction and the antibody amount in a simplified way. Containers for antibody preservation are screened, and a container is selected in a freezing/thawing test, capable of preserving 90% or more of antibodies. A high-density culture that uses the hollow fiber cartridge is now feasible. (NEDO)

FY 1999 project on the development of new industry support type international standards. Standardization of a measuring method of fuel consumption of hybrid electric vehicles; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Hybrid denki jidosha no nenpi sokutei hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of proposing a measuring method of fuel consumption of hybrid electric vehicle (HEV) to ISO and internationally standardizing it, test/study were made. The FY 1999 results were summarized. In this fiscal year, the following were conducted using one new vehicle in addition to the two HEVs used in the previous fiscal year: assessment of generative energy at braking, and verification of the results obtained in FY 1998 such as changes in the remaining battery capacity before/after the test. Further, study was made on 'the concretely described contents of each element of the standards' and 'the method to correct changes in battery capacity and improvement in measuring accuracy.' Moreover, the items to be considered at the time of measuring current were made clear. Based on these studies, the making of a draft on the standards was finished. In addition, the measurement by overseas mode was also made, and it was confirmed that this is an effective measuring method also for overseas mode. In the investigational study, standards/papers overseas were surveyed. Exchanges of opinion on the technical background, etc. were also made with persons who are making the same studies overseas for mutual understanding. (NEDO)

Research report of FY 1997 on the environmentally acceptable coal utilization system feasibility survey. Clean coal technology model project seminar held in Thailand; 1997 nendo seika hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (Tai ni okeru clean coal technology model jigyo seminar no kaisai)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-02-01

To reduce SOx with coal utilization, the desulfurization seminar diffusing the demonstration project of simplified desulfurizer introduction was held at the site in Thailand. The purpose is to reduce the environmental pollutants and contribute to the effective utilization of energy with coal utilization in Thailand. Invitation letters were sent to users of coal and heavy oil boilers through the Department of Factories, Ministry of Industry, Thailand, to call participation in the seminar. Inspection of the desulfurizer introduced in the factory of Thai Union Paper Public was included in the seminar for diffusing the project. The inspection site is in the demonstration project site of simplified desulfurizer introduction. There were a lot of participants from Thai users and from Japan. The seminar included the presentations from NEDO, JETRO, FTI, and MOSTE, introduction of general technology for processes of ENAA desulfurizer, introduction of demonstration unit plan by IHI, and introduction of operation of demonstration unit by TUP. 31 figs., 6 tabs.

FY 1999 project on the development of new industry support type international standards. Standardization for high-interoperability of optical disk systems; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Hikari disk system no sogo un'yosei kakuho no tame no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The R and D were conducted on the standardization for interoperability of optical disk system, and the FY 1999 results were summarized. In the study, for the volume/file structure specified by ISO/IEC 13346, the development of standards was made for interoperation of the UDF specified by OSTA. In this fiscal year, to avoid the problem on non-interchangeability of UDF which actually exists, enhancement of functions of a test tool for UDF interchangeability was tried. Namely, development was carried out of UDF interchangeability test tool, UAF related standards, and UAF related standards assessment system. Especially, it was formally announced that UDF security enhancement of UAF related standards will be included in UDF2.x in the OSTA conference held at the end of FY 1999. Also, a draft on the standard information was drawn up domestically. The standards including API are expected to be established as standards through activities in the next fiscal year. (NEDO)

FY 1999 project on the development of new industry support type international standards. Standardization for securing mutual connection among informative household electric appliances; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Joho kaden kikikan no sogo setsuzokusei kakuho no tame no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The R and D were conducted with the aim of the international standardization for securing mutual connection among informative household electric appliances, and the FY 1999 results were summarized. In FY 1999, the following were conducted: trial manufacture (for mass production) and evaluation of wide band POF (plastic optical fiber), trial manufacture and evaluation of home use small connector, and trial manufacture and evaluation of optical transceiver module. Various data required for the targeted standardization (transmission band: S400 or more, transmission distance: 100m) were obtained. In the next fiscal year, tests to demonstrate validity/reliability of the data are conducted so that the standards to be accepted as an international standard can be established. In the study of strategies of international standardization, the contents of the standards proposed were discussed, and activities of IEC/TC100 (multi-media) and the related TC were investigated. Early in the next fiscal year, the TC to be proposed is fixed, and international proposing activities are started such as the introduction of the standardization for this R and D to the organizations and persons concerned overseas. (NEDO)

Fiscal 1999 technical achievement report. Research and development project on the quickly effective international standards creation (Standardization of safety of light emitting diode or the like); 1999 nendo sokkogata kokusai hyojun sosei kenkyu kaihatsu jigyo seika hokokusho. Hakko diode nado no anzensei ni kansuru hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Since radiation of a laser diode (LD) is quite different from that of a light emitting diode (LED), evaluating their safety under one and the same standard (criterion) is questionable. The International Electrotechnical Commission (IEC), however, treats them in the same way. For the remedy of such contradiction and for the clarification of difference between the two devices in terms of radiation characteristics, they were quantitatively measured for spatial coherence and further measured for coherence dependency of their beam diameters. Well-supported threshold levels were prepared and biological tests were conducted for proposing a revision of the LED safety standard (IEC). As for the safety of equipment with built-in infrared devices, a measurement method was prepared as IEC61913 and devices are already at the CVD (chemical vapor deposition) stage. The result will be placed before the IEC/TC76 committee for deliberation of IEC60825-1 revision. Furthermore, to establish alignment between IEC and ISO (International Standardization Organization) in terms of laser-aided measurement which is the foundation for such committee deliberation, an ISO/IEC international joint group was created, and a technical recommendation was compiled and presented to the two standardizing organizations. (NEDO)

FY 1999 project on the development of new industry support type international standards. Standardization of digital image processing in household digital electronic devices; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kateiyo digital denshi kiki ni okeru digital gazo shori no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

As a framework of the processing of intellectual properties concerning the mobile videophone use coding system, MPEG-4, the paper took up the Intellectual Property Management and Protection (IPMP) framework, discussed a proposal for the standardization aiming at expanding IPMP functions, and summed up the FY 1999 results. In the activities of MPEG-4PF project in this fiscal year, four of the tools from Japan were extracted as candidates of the powerful tool which belongs to 'Simple and Core' of MPEG-4Visual and profile of MPEG-4Audio, and the international standardization was promoted. Especially, attention was paid to the mobile, promotion was made as a tool effective for heightening error resistance, and all the proposals were adopted. Further, attention was paid to the security field, and a proposal was made for IPMP expansion. The expansion makes up defects of the IPMP system which had already been proposed as a candidate for standardization. For the intensive discussion for this, a special work team was set up, and a special meeting was held at Tokyo University. (NEDO)

Fiscal 1999 technical research report. Research and development project on prompt-effect international standards creation (Standardization of gene amplification and analysis methods for genetic screening); 1999 nendo shinki sangyo ikusei sokkogata kokusai hyojunka kaihatsu jigyo seika hokokusho. Idenshi kensayo idenshi zofuku kaiseki hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the promotion of Japan's proposition for international standardization, PCR (polymerase chain reaction) Comprehensive Research Committee, Technical Promotion Committee, and Japan Bioindustry Association organized a 5-member overseas research team and dispatched the team to Europe and America where they held research interviews at government organizations and business corporations engaged in standardization promotion. The aims were to disclose trends of PCR method standardization and standardization in general in biotechnology. The team visited British Standards Institution, Association Francaise de Normalisation, German Institute for Standardization, Food and Drug Administration of America, American Society for Testing and Materials, PE Biosystem, Bio-Rad Laboratories, and Roche Molecular Systems. The objects of standardization at issue included techniques, tools, devices, and reagents to be used. It is found that in Europe and America there are standardization plans under deliberation for PCR-aided techniques, not for PCR itself, and that some are now approaching completion as national or local standards. It is also learned that in every standardizing organization there is a person responsible for each TC (technical committee) of CEN (Committee European pour Normalisation). (NEDO)

Fiscal 2000 report of research on the analysis and evaluation on data collected in project of field test of photovoltaic power generation for public and other facilities; 2000 nendo kokyo shisetsunadoyo taiyoko hatsuden field test jigyo ni okeru shushu data hyoka kaiseki kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of promoting photovoltaic power generation, analysis and evaluation were conducted on the data of the project of the field test in public facilities for example. This paper describes the fiscal 2000 results. The equivalent array operation time was 2.98 h/day and, by multiplying it by the output of the standard test condition, a generated output was obtained. The system generating efficiency was 0.102 while the inverter energy efficiency was 0.917 on the average. The average array performance ratio was 0.778 and the system performance ratio was 0.714. The analysis on cost effectiveness of the installed systems has an important bearing upon the future introduction, promotion and development. The power generating cost (the annual cost was calculated as the sum of the capital cost, the direct cost, and the administrative expenses) decreased as the installation year progressed, with the average at the sites installed in fiscal 1997 at 93 yen/kWh. The system cost (calculated by dividing the construction cost by the array capacity) also decreased as the installation year became more recent. The annual maintenance cost showed a wide range from 500 yen to 30,000 yen/kW. Answers from the sites that the systems were running smoothly were 38 to 45%, while those that trouble occurrence was frequent were 2.4% on the generating systems and 12.9% on the measuring systems. (NEDO)

Achievement report for fiscal 1997 (edition B) on auxiliary New Sunshine Project. Development of coal hydrogasification technology (Research by using experimental device); 1997 nendo New Sunshine keikaku hojo jigyo seika hokokusho (B ban). Sekitan suiso tenka gaska gijutsu kaihatsu - Jikken sochi ni yoru kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

With an objective of using practically the coal hydrogasification technology (the ARCH process), developmental research has been performed. This paper summarizes the achievements in fiscal 1997. In the research by using a small testing device, the Taiheiyo coal was used to have derived hydrogasification data (distribution and yield of the reaction products) in case of having changed the temperature, residential time and H{sub 2}/caoal ratio at a pressure of 7.0 MPa. In the developmental research on the injector, a test to verify mixing performance was performed by simulating the coal/hydrogen with gas/gas and coal/gas at normal temperature and pressure. Furthermore, discussions were given on the heat conduction analysis and cooling structure, whereas an injector was designed and fabricated. With respect to the hot model test to verify the performance of the injector, detailed design and partial fabrication of the test device were carried out. In addition, development was conducted on the coal/gas system mixing simulation to simulate the states of dispersion and mixing of the coal as the first phase of developing the mixing and temperature rise simulation. (NEDO)

FY 1999 project on the development of new industry support type international standards. Standardization of test/evaluation methods of telecommunication use fine ceramics; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Tsushin kikiyo fine ceramics no shiken hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

As to high frequency/ultra-high frequency band use fine ceramics, the R and D were conducted with the aim of establishing the evaluation method of electric characteristics such as dielectric constants and dielectric losses, and at standardizing and internationally standardizing the principle of the measuring method, preparation method of equipment and test pieces, measuring procedures, etc. The FY 1999 results were summed up. As to the measuring method of electric characteristics, enhancement of measuring accuracy was made for the millimeter wave coaxial exciting cavity resonator method and the Fabry Perot method. Further, field survey was made of the developmental trend of the measuring method in Europe and the U.S. Concerning measuring use standard test pieces, candidate materials were trially manufactured, and the shape/dimension of a part of the candidate materials were determined. As to surface basic properties, effects of surface shape and convex/concave faces of test pieces on characteristic evaluation were studied, and it was made clear that convex/concave faces were greatly influential. In the technical committee, how to proceed with the development was discussed in the first meeting, and evaluation methods and candidate standard substances were selected in the second meeting. (NEDO)

FY 1997 evaluation/analysis by site of the data collected in the field test project for photovoltaic power generation for public facilities. 1/3; Kokyo shisetsunadoyo taiyoko hatsuden field test jigyo ni okeru shushu data hyoka kaiseki kaku site betsu (1997 nendo). 1/3

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The data on field tests of the photovoltaic power generation were collected. The items for survey were as follows: horizontal insolation intensity, inclined insolation intensity, effective inclined insolation intensity, average temperature, array electric energy, system electric energy, load electric energy, system supply load, back flow electric energy, interconnected protective movement, disconnection hour, system operation hour, independent operation load, independent supply load, equivalent array operation, equivalent system operation, array output coefficient, system output coefficient, system utilization rate, system charging efficiency, INV effective efficiency, INV load factor, etc. The number of the places for survey is 37 including the following: Hikarigaoka Park of Sakata City, Koiwai Plant of Koiwai Dairy Product Co., Kameoka Ayumi Nursely School, Ichinoseki I-DOME, Okano Park, Kuriyama Park Health Sports Center, Mejiro University, Tokyo Hikarigaoka Sports Facilities, Regional Community Center, Yokohama Tobu Joint Purchase Center, Taemi-so Nursing Care Center for the Elderly, Uemichi School Meal Providing Center, Okayama Prefectural Office, Oita Prefectural Agricultural Research Center, Kanagawa Industrial Technology Research Center Institute, etc. (NEDO)

FY 2000 Immediate-effect type project for research and development for international standards supporting information technology industries. Comprehensive study on promotion of international standardization; 2000 nendo joho sangyo shien sokkogata kokusai hyojun kaihatsu jigyo seika hokokusho. Kokusai hyojunka suishin ni kakawaru sogo chosa kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The information technology and international standardization are studied for the elementary information technology, mechanical safety areas and electronic trading, aimed at achieving the international standards in a short time for the information industrial sector, which shows rapid technological development. The program for the elementary information technology includes development/standardization of the testing/evaluation methods for transparent electroconductive films for notebook computers, liquid crystal monitors or the like, specifically for the mechanical and physical properties. The program for mechanical safety areas includes definition of the closed space type mechanical safety monitoring techniques and use of safety-confirmation type sensors for the techniques, and standardization of the requirements of the protectors for use of the safety-confirmation type sensors, among others. The program for the electronic trading includes standardization of the electronic catalogues of the instrumentation devices, dictionaries of the instrumentation devices and device-screening processes. The other efforts include development of the applications and system infrastructure functions, construction of the demonstration test systems, and demonstration tests. (NEDO)

FY 1999 research report on the evaluation/analysis of the data collected in the field test project for the photovoltaic power system for public facility use; 1999 nendo kokyo shisetsu nadoyo taiyoko hatsuden field test jigyo ni okeru shushu data hyoka kaiseki kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

In this research, the photovoltaic power system is experimentally installed at various facilities (public facilities such as public hall, school and museum), and operated on a long term basis under the actual loads. Various kinds of data are collected/analyzed and used as the data useful for the full-scale introduction and spread. The photovoltaic power generation field test project for public facilities using the photovoltaic power system was started in FY 1992 by NEDO. Systems at 116 sites started operation by FY 1996, and in FY 1997 systems were installed at a total of 70 sites. The paper outlined the project and described the results of the collection/analyses of the operational data obtained at 145 sites where systems were installed from FY 1995 to FY 1997. The term of analysis in FY 1999 was made from April 1999 to December 1999, being different from usual, to avoid the Y2K problem on data collecting software, measuring use personal computer, etc. Further, since there are no sites where no systems were newly installed in and after FY 1998, there are no analyses of economical efficiency in and after FY 1999. The paper indicated a list of all the sites with system installation in FY 1995-1997 including the main items. (NEDO)

Energy supply/demand structure development survey project / comprehensive survey on energy supply/demand development. FY1997 survey on techniques for pyroelectric power generation systems; Energy jukyu kozo kodoka chosa jigyo / energy jukyu kodoka sogo chosa. 1997 nendo shoden hatsuden system no gijutsu chosa seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-05-01

Pyroelectric conversion systems were surveyed as the techniques for effective utilization of low-temperature waste heat sources. Described herein are the principle of pyroelectric power generation, including pyroelectric phenomenon, origin of pyroelectricity in polymers, and pyroelectric polymers and copolymers; utilization of the pyroelectric phenomenon, including hysteresis of pyroelectric materials, general pyroelectric conversion principle, pyroelectric conversion cycle, analysis of power output by an Olsen cycle, comparison with a steam engine, and power outputting methods; pyroelectric conversion systems, including heat regeneration method, plate type pyroelectric conversion devices using the heat regeneration method, and voltage controlling methods; and pyroelectric conversion outputting, including calculations of power output and loss, conduction-caused loss, pumping loss, and pyroelectric converter efficiency. Other items described herein include conceptual designs of 1 and 100 kW pyroelectric converters for utilization of waste heat, and current status of pyroelectric converter development at CANMET Energy Technology Center. (NEDO)

Project to aid development of an oil substituting fuel manufacturing technology in fiscal 1998. Report on the result of developing a technology to make cable covering materials into fuel; 1998 nendo sekiyu daitai nenryo seizo gijutsu kaihatsu hojo jigyo. Densen hifukuzai nenryoka gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

Research and development have been carried out with an objective to re-utilize waste cable covering materials as oil substituting energy. The research has been performed on behavior of chlorine and lead being substances that impede making the cable covering materials into fuel, development of a technology to remove chlorine, lead and copper, and pelletizing properties for fuel making. In the study of behavior of chlorine and lead, the following matters were made clear: dechlorination reaction completes within 30 minutes if pyrolysis temperature is higher than 300 degrees C; the more the amount of filler CaCO3 in test samples, the less the dechlorination amount; and secular deterioration does not affect the dechlorination amount. A technology has been developed successfully to remove the substances that hinder making the cover materials into fuel, achieving the target values of copper at 0.2% or less, lead at 0.3% or less, and chlorine at 5% or less. In developing the pelletizing technology that puts the cover materials into raw materials for blast furnaces, dechlorination rate of 90% was achieved by mixing coke/PVC at a ratio of 1/1 and dechlorinating it by using a rotary kiln. It was verified that the product is free of problems in particle size as the blast furnace raw material. (NEDO)

FY 1999 cooperation program - Comprehensive research cooperation in environmental technology. Research cooperation in toxic/hazardous waste management in the Laguna de Bay region; 1999 nendo kenkyu kyoryoku jigyo. Kankyo gijutsu sogo kenkyu kyoryoku - Raguna ko chiiki ni okeru yudoku yugai haikibutsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of establishing preventive measures for water contamination in the Laguna de Bay region, the Philippines, where the water contamination is in progress and the eutrophication is feared, a research cooperation project was carried out on the water quality contamination monitoring technology (measuring method/analysis method/prediction method). In the survey of the state of generation of toxic/hazardous waste, the following were grasped based on the existing data: amount of use of toxic/hazardous substances in factories, state of generation of waste, situation of the processing/disposal, etc. In the detailed survey of the situation of pollution in the Laguna de Bay region, specimens of water quality and bottom material were collected from the lake and rivers thereinto, and qualitative/quantitative analysis of contaminants was made using atomic absorption spectrophotometer and gaschromatograph mass spectrometer. As to the evaluation of pollutant sources and control method, the paper conducted the introduction of measures generally taken against pollutant sources, study of a method to grasp the behavior of contaminants by the environmental assessment method for the closed water area, etc. The training was also conducted for researchers/engineers widely in charge of management of toxic/hazardous waste in the Philippines. (NEDO)

Project in fiscal 2000 of developing international standards for supporting new industries. Standardization of thermal environment for creating comfortable living space; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kaitekina seikatsu kukan no sozo no tame no onnetsu kankyo no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective of proposing to ISO a thermal environment evaluation method, development has been performed on an evaluation technology to evaluate comfort and discomfort in non-constant and non-uniform thermal environment, and research has been carried out on structuring an evaluation standard. This paper summarizes the achievements in fiscal 2000. In developing the evaluation technology by using a 'human body thermal model' it was verified that the 'human body thermal model' being the achievement of the project to develop the human sensitivity measurement applied technology is effective as a method to evaluate non-uniform thermal environment, as a result of the experimental verification of the human testees. With regard to the effects on human body of thermal transient based on the testee experiment, such basic findings were derived that the thermal transient affects the psychological reaction even after movement, and that thermal sensitivity of aged persons of both sexes, and young generation shows greater positional difference in peripheral sections than in the trunk sections. The major standard being the object of this research is ISO 7730, for which discussions were given on the revision draft for the floor heating standard and the transient standard, the evaluation method using a human body model, and the evaluation method using a thermal mannequin as the new standards. (NEDO)

FY 1999 project on the development of new industry support type international standards. Standardization of evaluation testing method of thermal properties of polymer materials; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kobunshi zairyo no netsutokusei hyoka shiken hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of proposing it to ISO, the R and D were conducted of a new evaluation method of thermal properties of polymer materials. The FY 1999 results were summarized. In this fiscal year, the development of the ac Joule heating equipment was proceeded with based on the study at the technical committee, and the measuring device was installed. In the comparative measurement with conventional methods, study was proceeded with of the laser flash method, AC calorimetry method and specific heat measurement. In the technical survey, the developmental state of the ac method, especially, was examined as a testing method of thermal properties of polymer materials. It is in the stage of the basic research by keyword selection, and the search for literature is to be made in full scale. As to the needs in the industrial circle, as a result of the questionnaire survey made, it was found out that there were a wide variety of the needs for general-purpose/functional film materials, forming materials, composite materials, coating, adhesives, cohesive materials, etc. Further, as the application field, construction materials, agriculture, food, packaging, etc. were cited in addition to the magnetic recording in electric/electronic relations, sensor insulation, OA equipment, wiring board, etc. (NEDO)

FY 2000 Research and development project for creation of the standards. Standardization of information-providing technologies for establishing human/machine interfaces; 2000 nendo kijun sosei kenkyu kaihatsu jigyo seika hokokusho. Hito to kikai no interface kochiku no tame no joho teikyo gijutsu ni kansuru hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This survey/test/research project is aimed at standardization of providing information smoothly while securing safety for various types of drivers by introducing advanced technologies into vehicles.The methods of evaluating priorities of 105 items of information for drivers, which are taken up by ISO, are followed to find that 5.90, 2.05 and 0.11 items are selected for the alarm, route guiding and general information systems, respectively. These results are in agreement with the related literature survey results. The test results of the visual/auditory displays corresponding to the priority information types indicate that the adequate alarm displays are 'red/50nt/0.2 seconds, 30% frequency/6.0 degrees' for the visual sensation, and '80dB/2.0KHz+1.5 harmonics/0.2 seconds, 70% frequency' for the auditory sensation. The study on information volume and information recognizing time indicates that the symbol pattern is better than the letter pattern for the simultaneous display of up to 2 items learned beforehand. The others studied include alarm designs and management of two or more alarms. (NEDO)

Achievement report for fiscal 1981 on Sunshine Program survey and research. Joint projects on solar energy between Japan and Australia, etc. (Japan-France technological cooperation on solar energy); 1981 nendo Nichigo nado taiyo energy gijutsu kyoryoku jigyo seika hokokusho. Nichifutsu taiyo energy gijutsu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

A curved-surface thermal power system just before completion is visited, located on the island of Corsica. Light is collected by a curved-surface mirror in which narrow flat-surface mirrors with their length matching the linear collector width are attached amphitheater-wise to a curved-surface foundation built of concrete, and a linear collector performs tracking along the focal line. Exchange of information and comparative study will be required concerning this system. As for passive use of heat, a flat-plate collector has reached a level of practical application at homes in the low-temperature domain. Sites related to long-term basic research and seawater desalination are also visited. As for collector in the high-temperature domain, a THEK (Thermo-Helio-Electricity Kilowatt) system which is a spherical mirror collector is on the initial stage of planning. It is important to compare various types of curved-surface systems for their merits and demerits. As for the production of solar cells for photovoltaic power generation, it is monopolized by the Photowatt Corporation, with most of the products to be exported for use as independent power sources. As for future development, the casting technique will be industrialized at the end of 1983, the ribbon type will come next, and the amorphous material will be farther in the future. The task is how to enhance technical cooperation in the future. (NEDO)

FY1995 research on humanoid; 1995 nendo humanoid kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The future robot must be a sensor-complex with high intelligence and flexible mechanical body. The purpose of the project is to improve the basic technologies by making a prototype of the human-like robot to work with human using various communication channels such as voice, facial expressions, and motion of the head, eyes, arms and legs. The following basic technologies are successfully developed and two humanoid robots were built as the total systems. They can perform some physical works communicating with human. Moreover these robots were connected to ISDN network for the experiments of tele-robotics. 1. a environment and human face understanding using vision and audition. 2. a speech conversation under the ordinary room environment. 3. a human machine communication using gesticulations. 4. a flexible human-like robot head, arms and hands. 5. a biped walking using the dynamic balance control. (NEDO)

International joint research of medical and walfare appliances; Iryo fukushi kiki kokusai kyodo kenkyu jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

To further elevate the medical level and to actively enhance Japan`s contribution to the world in its effort to properly meet the task of advancing longevity of men common to all the advanced countries, investigations were made to study how international joint research should be conducted in the field of medical and welfare appliances. Candidate projects in international joint research and investigations up to fiscal 1993 were arranged, and explanation was made about the strategic and long-term research and development projects (started in fiscal 1995) about medical and welfare appliances undertaken by the Ministry of Trade and Industry of Japan. The two are quite similar to each other, the Ministry of Trade and Industry program comprising six projects that are micropores collection of blood/microdose analysis, high precision three dimensional image assisted diagnosis, less invasive surgery, artificial organs, care assisting intelligent equipment, and welfare equipment for care at home, centering about which international joint research should be propelled. Visits were made to the scenes of research and development of advanced medical and welfare appliances in the U.S. and Canada and their actual state was studied in search for possible joint researches. Further, research and development institutions in Europe were visited and information was exchanged. 25 figs., 15 tabs.

17th Symposium of NEDO projects. Geothermal subcommittee; Chinetsu bunkakai. Dai 17 kai jigyo hokokukai

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-09-01

Described herein are the reports presented to the geothermal subcommittee. The NEDO's Geothermal Research Department is developing the technologies for accurately predicting the reservoir changes in the future by the geothermal development promotion investigations for distributed conditions of geothermal resources and related environmental impacts, and also by clarifying the hydrogic characteristics of the fracture systems which form the reservoirs. The department is also implementing the projects for investigating/ researching possibilities of resources distribution conditions and utilization for eventual commercialization of the deep underground geothermal resources, and also investigating utilization of small- to medium-sized geothermal binary power generation systems for effective utilization of unutilized geothermal energy. The geothermal technology development group is developing the technologies for the binary cycle power generation plants which effectively utilize unutilized medium- to high-temperature geothermal water for power generation, and also the technologies for collecting conditions at the bottom of a geothermal well being excavated in real time to improve efficiency and precision of the excavation. The other technologies being developed include those for excavation and production essential for development of power generation systems using high-temperature rocks and deep underground geothermal resources, the former being expected to contribute to expanded utilization of geothermal resources and the latter to increased geothermal power generation capacity. (NEDO)

17th Symposium of NEDO projects. Geothermal subcommittee; Chinetsu bunkakai. Dai 17 kai jigyo hokokukai

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-09-01

Described herein are the reports presented to the geothermal subcommittee. The NEDO's Geothermal Research Department is developing the technologies for accurately predicting the reservoir changes in the future by the geothermal development promotion investigations for distributed conditions of geothermal resources and related environmental impacts, and also by clarifying the hydrogic characteristics of the fracture systems which form the reservoirs. The department is also implementing the projects for investigating/ researching possibilities of resources distribution conditions and utilization for eventual commercialization of the deep underground geothermal resources, and also investigating utilization of small- to medium-sized geothermal binary power generation systems for effective utilization of unutilized geothermal energy. The geothermal technology development group is developing the technologies for the binary cycle power generation plants which effectively utilize unutilized medium- to high-temperature geothermal water for power generation, and also the technologies for collecting conditions at the bottom of a geothermal well being excavated in real time to improve efficiency and precision of the excavation. The other technologies being developed include those for excavation and production essential for development of power generation systems using high-temperature rocks and deep underground geothermal resources, the former being expected to contribute to expanded utilization of geothermal resources and the latter to increased geothermal power generation capacity. (NEDO)

Natural gas distribution system for Peninsular Malaysia. Malaysia ni okeru toshi gas jigyo no sosetsu

Energy Technology Data Exchange (ETDEWEB)

Ohashi, T [Tokyo Gas Co. Ltd., Tokyo (Japan)

1993-03-30

Tokyo Gas Co., Ltd. established in 1992 Gas Malaysia Sdn. Bhd, a joint venture company with investments from the Malaysia side, and begun full-fledged activities for supplying natural gas in Peninsular Malaysia. This paper explains the summary of the project. With a background of affluent resources including natural gas reserve of 1.9 trillion m[sup 3] as of 1992, Malaysia is promoting various projects to diversify and refine local energy consumption patterns and improve petroleum exporting capacity. The said joint venture project is one of the international bids executed by the national petroleum company, Petronas, in which Tokyo Gas Co., Ltd. and Mitsui and Co., Ltd. were selected as their partner. The company business includes supply and sales of petroleum, as well as construction of pipelines to support the former activities. Engineers have been either stationed or sent to the country as technical cooperation including necessary technical transfer. This project is highly significant in terms of contributing to growth of economy in both countries and to solving global environmental problems. 6 figs.

FY2000 report on the survey results of medical/engineering cooperative research project, additional research on {sup 13}C-MRS for non-invasion type brain metabolism measurement; 2000 nendo igaku kogaku renkeigata kenkyu jigyo mushinshuteki no taisha keisokuyo {sup 13}C-MRS sochi ni kakawaru tsuka kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

The basic data are collected by the experiments, in order to optimize the {sup 13}C-MRS analyzer for non-invasion type brain metabolism measurement. The tests are conducted for normal aged volunteers and volunteer patients of, e.g., dementia as the subjects. Each subject is orally dosed with glucose marked with {sup 13}C at the 1-site, and the metabolized {sup 13}C glucose signals from two points in the back of the head are observed as the MR spectra for a total of 3 hours. The time-series data of the {sup 13}C glutamic acid and glutamine signals are analyzed, to determine metabolism speed of the TCA circuits, among others, which provides important information for understanding the brain cell functions. It is 0.33{mu}mol/g/minute as the average of the 5 subjects of normal aged volunteers, which is on a level with that of the young volunteers. On the other hand, it is 0.26{mu}mol/g/minute as the average of the 4 subjects of volunteer patients of dementia, although there is no difference of statistical significance between these values. These results, therefore, suggest that the patients of dementia tend to have deteriorated brain metabolism than the healthy persons. (NEDO)

Report on the FY 1999 research cooperation follow-up project on the development of manufacturing technology supported by advanced and integrated information system through cooperation; 1999 nendo kan'i sosagata denshi sekkei seisan shien system no kaihatsu ni kansuru kenkyu kyoryoku follow up jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

In FY 1999, the follow-up project was conducted on the development of manufacturing technology supported by advanced and integrated information system through cooperation (MATIC). The project included the grasp of the state of activity, announcement of the achievement, field survey, etc. of China, Indonesia, Malaysia, Singapore and Thailand. China carried out the system development and demonstrative tests in the fiber/apparel field, trying to spread the MATIC system. Indonesia is planning to spread the use of electronic catalog of automotive parts/electronic parts toward small/medium companies through internet. Malaysia was in charge of the development in the field of home electric appliances and demonstrative tests. They use the results so as to meet the demand in the domestic industry, aiming at spreading it in the country. Singapore uses the electronic catalog system to make it apply to the informatization project of the country. Thailand is making efforts for the spread of the MATIC results through the prototype model. (NEDO)

Fiscal 1996 research report on the PV power generation field test project for public facilities. Evaluation and analysis of collected data for every site (1/2); 1996 nendo kokyo shisetsu nadoyo taiyoko hatsuden field test jigyo ni okeru shushu data hyoka kaiseki. Kaku site betsu (1/2)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

As a part of the PV power generation field test project, this report summarizes the monthly collected data for every site in fiscal 1996. The test sites include various public facilities such as park, school, university, museum, Shinkansen platform, laboratory, technical center, training building, local governmental hotel, health athletic center, community center, joint purchase center, consumers' cooperative (CO-OP), school meals provision center, prefectural office building, police station garage, water purification plant, general disaster prevention center, and health center. Collected data items are as follows: total solar irradiation (kWh/m{sup 2}), average air temperature, array power, system power, load power, power system supply load, reverse power flow, self supply load (kWh for every item), system disinterconnection time (min), system operation time (min), equivalent array/system operation time, array/system performance ratio, system use factor, system generation efficiency, effective inverter efficiency, and inverter load factor. (NEDO)

Fiscal 1998 research achievement report. Project for developing key technologies for electronic devices (Projection X-ray exposure process technology and active reflective device structure technology); 1998 nendo denshi device kiban gijutsu kaihatsu jigyo seika hokokusho. Shukusho X sen roko process gijutsu to active hansha kozogata keisei gijutsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-05-01

Studies were conducted for the development of technologies of the very advanced level relating to an ultrafine machining process and high-performance reflector type liquid crystal display structure formation. Studied in the research and development of projection X-ray exposure process technology were multi-layer film formation, absorbing body film formation, absorbing body machining, multi-layer film mask defect evaluation, and cleaning for defect reduction. As the result, multi-layer film formation by Helicon sputtering and formation and machining of film with Ta acting as absorbing body therein were carried out, and it was found by actual exposure experiments that there were excellent X-ray reflectivity and absorbing body contrast. Furthermore, a study was made of cleaning using dummy foreign matters, and 100% removal of dummy foreign matters was achieved across a range up to the 70nm level. Studied in the development of active reflective device structure technology were the addition of an electrical control function to the reflector, addition of an unreflected rays absorbing function, production of a bias stabilized device for the practical application of a memory function, and the development of materials for the fabrication of the said devices. (NEDO)

Achievement report in fiscal 1999 on commissioned research project. 'Model project for facilities to effectively utilize wastes from industrial complexes in Thailand' Project for 1999 Volume 1; 1999 nendo seika hokokusho. Tai ni okeru kogyo danchi sangyo haikibutsu yuko riyo setsubi moderu jigyo - 1

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective to reuse industrial wastes and effectively utilize them as a petroleum replacing energy resource, and attempt to reduce consumption of fossil fuel in Thailand where increase in discharge of industrial wastes is estimated, a model project for facilities to effectively utilize wastes from industrial complexes has been carried out. This paper reports the achievements in fiscal 1999. Specifically, the project calls for incineration in fluidized bed incinerators of industrial wastes discharged from factories in industrial complexes possessed by the Industrial Estate Authority of Thailand (IEAT), recovery of waste heat from waste heat recovering boilers to generate process steam, which is supplied to the factories in the complexes. The current fiscal year, which is the first current year of the project, has put into order the operations shared by Japan and Thailand, compiled the various procedures and schedules into the form of appendices to the agreement, and executed signing of the agreement. Thereafter, the Japanese side has carried out decision on the specifications of the facilities, the basic designs, the detailed designs of facilities to be arranged by Japan, and the fabrication of some of the devices according to the descriptions of the agreement appendices. The volume 1 summarizes the agreement appendices, and the specifications of the main devices. (NEDO)

FY 2000 Development of international standard supporting new industries. Standardization of the test method for performance evaluation for polymer products under critical environment; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kakoku kankyoka ni okeru kobunshi seihin no seino hyoka shiken hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This project is aimed at development of the testing methods which can adequately predict resistance of polymer products to weather in various areas of largely different environmental conditions. Described herein are the FY 2000 results of the outdoor exposure tests, and the tests in which the samples are exposed to light from a laboratory source and to a solar light-concentrating test unit. The FY 2000 project include the exposure of the samples directly to the outdoor conditions and glass-filtered light, which are continued from the previous year; solar light-concentrating type exposure tests conducted in Arizona, USA, started in this year; and reproduction tests for the exposure to a xenon lamp light, review of short exposure time areas and spectral degradation tests, among others. The program for evaluating the reference materials includes measurement of cumulative property changes of 4 types of plastic and 10 types of rubber materials by the exposure tests. The tests of resistance of plastics to weather have been exposing the samples, stabilized and not stabilized, for 16 months. For the reference candidate samples, the data of exposure for 1 month are collected 16 times. The tests of resistance of the rubber materials to weather reveal that each sample is deteriorated by hardening and deterioration proceeds with time. (NEDO)

Fiscal 1999 achievement report on the venture business assisting type regional consortium - Minor business creation base type. Development of environmental protection oriented technology for effectively utilizing waste paper; 1999 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Kankyo hozengata no koshi no yuko riyo gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The effort aims to use low grade waste paper out of various grades of waste paper, whose recovery does not make good progress, as a raw material for the development of value-added, commercially competitive products and to contribute to the enhancement of waste paper recovery. A dry pulverization method less polluting the environment and not requiring a drying process is established, and types of waste paper and optimum conditions for their pulverization are made clear. A molding system using a steam injection method capable of atmospheric pressure control is established, and this enables the molding of pulverized waste paper not only into flat boards but also into corrugated boards. It is found that water contained in the waste paper alone produces a result similar to that expected from steam injection. A partitioning board is produced from waste paper, and it is found to be near the conventional product in terms of noise absorption. Old newspaper and corrugated cardboard are pulverized and an air filter is developed, which is similar to the conventional product in terms of operating efficiency and life. Waste paper is carbonized, and then charcoal with more pores than the conventional charcoal is produced. The porous charcoal is found to be usable in vegetable beds. (NEDO)

Fiscal 2000 achievement report on the venture business assisting type regional consortium - Core industry creation type. Research and development of polisher robot system using intelligent force control; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Intelligent ryoku seigyo wo mochiita kenma robot system no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The effort aims to automatize the manufacture of wooden furniture by robotizing the polishing work in the field of wooden furniture manufacturing, making use of the seeds provided by intelligent force control technologies. The intelligent force control technologies ('Delicate control of force for the open architecture type industrial robot' and 'Method for target orbit generation not requiring joystick teaching') of Saga University and the interior laboratory of Fukuoka Prefectural Industrial Research Institute are evolved and applied, and are integrated with the 3-dimensional object modelling technology developed by the mechanical and electronic laboratory, Fukuoka Prefectural Industrial Research Institute, and the CAD (computer aided design) data conversion technology developed by ASA Systems Inc. The result was a polisher robot system experimentally fabricated to satisfy the need of an automated polishing process in the wooden furniture manufacturing industry. The robot was tested, and achieved a surface coarseness level of 5{mu}m or less. As for the manufacturing rate, it attained a rate of approximately 100mm/s which was two times higher than the rate to be expected from a skilled worker. (NEDO)

Fiscal 1999 technical achievement report. Development project on prompt-effect international standards for developing new industry (Standardization of gene amplification and analysis methods for genetic screening); 1999 nendo shinki sangyo ikusei sokkogata kokusai hyojunka kaihatsu jigyo seika hokokusho. Idenshi kensayo idenshi zofuku kaiseki hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

There is a move in Europe and America to establish their own standards for the polymerase chain reaction (PCR) technique although it is a technique essential to biotechnology, and it is feared that such will restrain Japan's activities. In its effort to counter the move, Japan is exerting its own endeavors, hoping that it will profit from international standardization of criteria for the PCR technique. The Japanese effort aims at establishing international standards by unifying measuring procedures in the PCR technique and by enhancing the general-purpose feature of the data involved. In concrete terms, items available on the market, such as test and research equipment, reagents, and electronic instruments for use in measurement, are compared with each other in terms of performance, and basic specifications necessary for standardization and basic data on quality are collected. The effort involves, in more concrete terms, the measurement of thermal cycler temperature distribution, the evaluation of heat-resistant DNA (deoxyribonucleic acid) polymerase temperature sensitivity and accuracy, and the evaluation of performance of CCD (charge coupled device) camera systems and Polaroid camera systems to be used for the evaluation of PCR products. (NEDO)

Fiscal 2000 survey report on Asia/Pacific Regional Environment Problems Researcher Exchange Promotion Projects. Construction of Environmental Technology Research Network in the Asia/Pacific Region; 2000 nendo Asia Taiheiyo chiiki kankyo mondai kenkyusha koryu sokushin jigyo hokokusho. Asia/Taiheiyo chiiki kankyo gijutsu kenkyu kaihatsu network kochiku chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of developing and popularizing environment conservation technologies in the Asia/Pacific region, activities were conducted for Environmental Technology Research Network in the Asia/Pacific Area (ETERNET-APR). In this fiscal year, under the motto of Expansion of International Collaborative Researches on Environmental Technology, a 7th international workshop was held in Yokkaichi City, Mie Prefecture, with the attendance of approximately 60 people in Japan and from abroad. Researchers from overseas, in addition, attended a 10-day training program at the National Institute for Resources and Development and others in preparation for the embodiment of international collaborative research. A survey was conducted overseas for the promotion of database utilization and registration and for grasping the problems intrinsic to the respective research institutes and problems to occur at every stage of development. People's Republic of China was visited, where a miniscale workshop was held, study tours were made, and opinions were exchanged. It was actually felt, at the places that were visited, that ETERNET-APR was certainly in function in various fields. (NEDO)

Fiscal 2000 achievement report. Venture business assisting type regional consortium - Minor business creation base type (Development of aluminum alloy casting system using aluminum titanate ceramic member); 2000 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Chitansan aluminium ceramics buzai wo shiyoshita aluminium gokin chuzo system no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

An automatic liquid metal charging system driven by a linear induction type electromagnetic pump is developed, with its members to be in contact with liquid aluminum alloy being constituted of aluminum titanate ceramics not to be wetted by liquid aluminum alloy and highly resistant to thermal impact. Technologies for casting aluminum titanate ceramic members in plaster molds, CIP (cold isostatic pressing) molding, and burning were established. The mechanism of wettability of liquid aluminum alloy on aluminum titanate ceramic members was elucidated, and an aluminum titanate ceramic member with a dense spinel layer formed thereon in situ was developed for improvement on non-wettability. The developed member remained non-wettable more than six times longer than conventional members. A special electronic counter mechanism was developed by installing in a conduit an aluminum titanate ceramic made impeller whose revolution was converted into electric signals for the measurement of the amount of charged liquid. A non-asbestos polycrystalline alumina-silica fiber was selected as the insulator for the melting/holding furnace, which enabled 30% energy conservation as compared with the conventional type. (NEDO)

Achievement report in fiscal 1999 on commissioned research project. 'Model project for facilities to effectively utilize wastes from industrial complexes in Thailand' Project for 1999 Volume 3; 1999 nendo seika hokokusho. Tai ni okeru kogyo danchi sangyo haikibutsu yuko riyo setsubi moderu jigyo - 3

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective to reuse industrial wastes and effectively utilize them as a petroleum replacing energy resource, and attempt to reduce consumption of fossil fuel in Thailand where increase in discharge of industrial wastes is estimated, a model project for facilities to effectively utilize wastes from industrial complexes has been carried out. This paper reports the achievements in fiscal 1999. Specifically, the project calls for incineration in fluidized bed incinerators of industrial wastes discharged from factories in industrial complexes possessed by the Industrial Estate Authority of Thailand (IEAT), recovery of waste heat from waste heat recovering boilers to generate process steam, which is supplied to the factories in the complexes. The current fiscal year, which is the first current year of the project, has put into order the operations shared by Japan and Thailand, compiled the various procedures and schedules into the form of appendices to the agreement, and executed signing of the agreement. Thereafter, the Japanese side has carried out decision on the specifications of the facilities, the basic designs, the detailed designs of facilities to be arranged by Japan, and the fabrication of some of the devices according to the descriptions of the agreement appendices. The volume 3 summarizes the inspection reports other than those included in the Volume 2. (NEDO)

Fiscal 2000 operation report. Fiscal 2000 model project for promoting advanced utilization of coal (Survey on data control system for advanced utilization of coal in Japan); 2000 nendo sekitan kodo riyo shuishin moderu jigyo gyomu hokokusho. Nihon no sekitan kodo riyo ni kakawaru data kanri system chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the purpose of contributing to the drafting of, for example, measures for securing coal resources for Japan and strategies for developing coal utilization technologies from the standpoint of the world climate of the coal supply/demand in the future, database was built concerning coal information such as coal-related supply/demand trend, technological development and utilization status in Japan and foreign countries, with the results of fiscal 2000 reported. In the preparation of related applications, a jump function in the case of pages unregistered with related subjects was added to the coal information retrieval system completed last year, as were a subdividing function of retrieval conditions and a link function to pages of a technical term dictionary. In the arrangement of the database classified by the fields, programs were prepared on 14 tables primarily in relation to supply and demand, with the collection, processing and registration of the data performed. In addition, in order to deal with the clarification of the patent licensing of GIF related technologies, there was developed a graph display program using a general-purpose language, Java. (NEDO)

FY 2001 report on the new energy vision of the Ishigaki City area. Survey for working out 'the project for the introduction of biomass energy in the central urban area of Ishigaki City'; 2001 nendo Ishigaki shi chiiki shin energy vision sakutei tou jigyo hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2002-02-01

Study was made of potentialities of the project of 'an energy supply system for biomass energy using business-derived raw refuse' indicated in 'the new energy vision of Ishigaki City, Okinawa Prefecture.' The amount of the recovered business-derived raw refuse was set at 5.6t at the minimum as against the discharged amount of 8t, and it was calculated that the amount of the biogas generated from the high temperature methane fermentation would be 757.7 m{sup 3}/d. The amount of the suppliable energy calculated from the above was 1,102.4 kWh/d in gas engine. Further, as to the energy demand, supposing the energy demand in large-scale hot bath facilities using salt as a resource of the area, it was calculated that the energy demand would be approximately 1MWh/d altogether with that in the biogas plant. As a result of the study of profitability of the project, the following was found out: it takes 25 years to recover the invested capital in the case of carrying out the biogas plant project alone and 18 years to recover it in the case of carrying out the hot bath facility project alone. In the case of carrying out both projects as one, it takes 18 years to recover the invested capital, the same as in the case of carrying out the hot bath facility project alone, but a great shortage from 6 years to 3 years is shown of the period required to get out of the cumulative deficit. (NEDO)

FY1998 survey on IEA international cooperation project on demonstration and survey of new load leveling methods (participation in the IEA/DSM task VI); 1998 nendo fuka heijunka shinshuho jissho chosa IEA kokusai kyoryoku jigyo 'IEA/DSM task 6 eno sanka ni tsuite' chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

It is intended to participate in the IEA international cooperation project related to DSA, exchange items of information, and promote demonstration and survey of new load leveling methods. The existing and newly proposed DSM mechanisms as the achievement of the previous tasks were put into order. The arena of information exchange and discussions was prepared through use of the Internet homepage for the IEA/DSM implementation agreement. Necessary official policies were also made available. Points of precautions when the mechanisms of other countries are used in Japan: the key to the success depends on social or cultural situations that work as the base; therefore, comparisons and analyses are necessary on such elements as customers as the object, energy projects and governments; compatibility of the situation and pattern of the demand side with the DSM technologies governs the reasonability thereof; the types of the mechanisms are narrowed down by size of the customer division, consumption pattern, electric power quality and safety, and needs on the flexibility; proliferation levels of the DSM technologies determine the appropriate mechanisms; and how the DSM is conceived against the final consumption is governed by the conception by both of the customers and the government. (NEDO)

Fiscal 1998 R and D project on global environmental industrial technology. R and D result report on environment- friendly production technology (advanced chemical synthesis reactor); 1998 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo. Kankyo chowagata seisan gijutsu (kokino kagaku gosei bio reactor) kenkyu kaihatsu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

For high-efficiency production of substances by bioreactor, study was made on a bio-control mechanism as its elementary technology. On the study of breeding technology by expression control, the structure design of a control region and development of new expression vectors had been finished, and study was made on breeding of high-efficiency recombinant production cells by using candidate expression vectors. On the study of breeding technology by multi-stage enzyme reaction control, the enzyme gene of a system synthesizing cysteine from glycerol was searched, and hydroxypyruvaldehyde hydrogenase gene was isolated as substance production model. Cysteine production Escherichia coli combined with serineacetyl transferase gene was also prepared. In addition, study started on cloning of hydroxyacetone oxidase gene. On development of reactor system technology, for conversion of serine to cysteine, study was made on optimization of a reaction condition by theory of enzyme reaction rate. (NEDO)

FY 2000 report on the project on the researcher dispatch type international joint research survey. Survey of the internationalization of research on the effective utilization technology for energy resources; 2000 nendo kenkyusha hakengata kokusai kyodo kenkyu chosa jigyo hokokusho. Energy shigen yukoriyo gijutsu kenkyu kokusaika chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

As to themes of the research survey which contribute to upgrading/diversification of the effective utilization of energy resources and are important in increasing cooperative relations with overseas countries, survey research was conducted by dispatching investigators. Relating to long-life Si solar cells, research survey was made on the reduction in deterioration of solar cell. Concerning the hydrogen carbonless energy system, the economical efficiency of a natural energy/hydrogen combined system was studied for all areas of Aomori prefecture. About the development of the multiple chamber type artificial pancreas for patients with serious diabetes, study using model dogs was investigated. As to the processing of PVC waste, the mechano-chemical method was discussed in the U.S. The paper further surveyed the following: PDE application to the aerospace field, joint developmental study of the reuse type space transport system by Japan and Russia, treatment/recycling of the electric/electronic equipment waste including toxic substances, technology of the manufacture of nano-particles and evaluation of optical characteristics of nano-structures, etc. (NEDO)

FY 1997 report on the verification survey of new mechanisms for load leveling. IEA`s international collaboration `Participation of Japan in IEA/DSM Task VI`; 1997 nendo chosa hokokusho (fuka heijunka shinshuho jissho chosa). IEA kokusai kyoryoku jigyo `IEA/DSM task IV eno sanka ni tsuite`

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

Current electricity markets in Europe and the USA are drastically changing due to the introduction of competition principle and the reconsideration of business systems. Are also changing the activities and their forms of DSM (demand side management) for load leveling which has been conventionally conducted by electricity companies for the efficient operation of facilities. Task IV and Task VI aim at developing new mechanisms to promote DSM in the changing electricity markets as well as disseminating and communicating information on the new mechanism. Japan participates in Sub-task IV/6 and 7 and Task VI. Activities for developing new mechanisms are divided into Phase 1 and Phase 2. The Phase 1 includes review of existing mechanisms and preliminary development and evaluation of new mechanisms. The Phase 2 includes the detailed development of new mechanisms and evaluation criteria, communication and information about mechanisms, and identification of the public policy implications which would follow a decision by the responsible authorities to implement each of various DSM mechanisms. The time frame of Phase 1 is between February 1996 and March 1997, and that of Phase 2 is between January 1997 and December 1999. 2 figs., 4 tabs.

Fiscal 1999 technical achievement report. Development project on international standards for supporting new industry (Standardization of method for evaluating physical properties of new glass at high temperatures); 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. New glass koon bussei no hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

In the manufacture and processing of high quality glass to be used with electronic devices and displays, values representing its physical properties at high temperatures, such as viscosity, density, cubical expansion coefficient, and surface tension are necessary. Studies were conducted about techniques for evaluating physical values of such high temperature molten materials, and efforts were under way to develop the research results into international standards. Techniques for measuring physical values of high temperature molten soda ash based glass were improved for higher precision, and techniques for evaluating physical values of high temperature molten borosilicate glass were studied. Delegates were sent to International Commission on Glass (ICG) and technical committee TC18 for joining discussion, decision was made that researchers participate in robin tests on molten glass thermal conductivity, density, and cubical expansion coefficient, and pertinent activities were launched. (NEDO)

Fiscal 2000 information collection/analysis project on basic research for coal resource exploitation. Research on technology of low-concentration methane gas recovery from underground coal mine; 2000 nendo sekitan shigen kaihatsu kiso chosa joho shushu kaiseki jigyo. Konaikutsu tanko ni okeru teinodo methane kaishu gijutsu chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Technical trends were surveyed concerning the recovery and the use as fuel of low-concentration methane gas or the like contained in the air ventilated out of coal mines. Methane gas recovery technologies include high-temperature incinerators and catalytic incinerators designed to collect heat, method of conversion of methane to CO2 using microbes named methanotrophs, and adsorption methods using activated charcoal, zeolite, or the like. Among technologies that have reached a practical level in the utilization of mine methane gas, there are the temperature regenerative flow-reversal reactor (TFRR) and the catalytic flow-reversal reactor (CFRR) utilizing high-temperature oxidation reaction. TFRR has been reported effective by MEGTEC System after a 6-month operational test of a 3.0m{sup 3}/s plant at a British coal mine. Test and research are over with CFRR, which is now ready for a commercial scale verification test. Recovery by adsorption, though worth further research efforts, is economically away from commercialization at the present stage, and wants more studies of adsorbents, etc. (NEDO)

FY 1998 Report on development of technologies for commercialization of photovoltaic power systems. International co-operative project (Information collected for IEA Solar Heating and Cooling Programme); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu kokusai kyoryoku jigyo. IEA taiyo reidanbo kyuto program ni kansuru joho shushu

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

The IEA/ Solar Heating and Cooling Programme (SHCP) committee members were dispatched to the IEA/SHCP Executive Committee and Expert Meetings, to collect information, present the reports and hold the discussions, among others. Described herein are the results. The third Expert Meeting of the IEA/SHCP Task 23 prepared the document covering the examples of solar energy use in large buildings and distributed them in Subtask A, and proposed and discussed the comprehensive performance evaluation methods and simulation-based design tools in Subtask C. The second workshop of the IEA/SHCP Task 25 discussed evaluation of the current technologies for solar assisted air conditioning, design of the solar assisted cooling systems, economic evaluation and market researches, investigations of cooling system hardware, and development of simulation programs and design tools. The examples of solar cooling are mostly found in Japan, and European countries are conducting experiments and field tests, because of lack of commercial grade freezers. (NEDO)

Fiscal 1997 research report on the PV power generation field test project for public facilities. Evaluation and analysis of collected data for every site (2/3); 1997 nendo kokyo shisetsu nadoyo taiyoko hatsuden field test jigyo ni okeru shushu data hyoka kaiseki. Kaku site betsu (2/3)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

As a part of the PV power generation field test project, this report summarizes the monthly collected data for every site in fiscal 1996. Collected data items are as follows: horizontal/total/effective solar irradiation (kWh/m{sup 2}), average air temperature, array power, system power, load power, power system supply load, reverse power flow (kWh for every item), power system protective operation frequency, system disinterconnection time (min), system operation time (min), self-operation load, self-supply load, equivalent array/system operation time, array/system performance ratio, system use factor, system generation efficiency, effective inverter efficiency, and inverter load factor. The test sites include various public facilities such as doctor's office, newspaper office, general building for public corporations, primary school, hot water pool, health center, public hall, town/ward office, water purification plant, consumers' cooperative (CO-OP), university, high school, technical center, training center, nursery school, kindergarten, and nursing home for the aged. (NEDO)

Fiscal 1999 achievement report on the venture business assisting type regional consortium - Minor business creation base type. Development of simplified extraction/purification method for highly purified large-size plasmids; 1999 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Kanbenka kojundo ogata plasmid chushutsu seiseiho no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The project aims to develop biotechnological industries in Okinawa Prefecture by embodying a method for obtaining large-size plasmids in a short time at low cost without a special apparatus, for which efforts were made to develop and commercialize a kit comprising an eluate from plasmid cells and a set of columns and eluate for purification. Under this project, University of the Ryukyus well experienced in the handling of plasmid DNAs and Advanced Medical Biological Science Institute jointly developed a 'simplified extraction/purification method for highly purified large-size plasmids.' The developed techniques or methods are described below. A concentration method was developed not using centrifugal operation for escherichia coli cultured in a closed mass culture device. A buffer exchange method in a closed system was developed, continuous from escherichia coli concentration to elution. A column assisted DNA purification method consuming but a short time was established. With these combined, the development is now complete of the technology and device for plasmid DNA elution from escherichia coli by an uninterrupted operation in a completely closed system. (NEDO)

FY 1999 Report on the technical results. Research and development project for quick-effect type international standards for creating new industries (Standardization of the wireless IC tags for logistics management); 1999 nendo sokkogata kokusai hyojun sosei kenkyu kaihatsu jigyo seika hokokusho. Butsuryuyo musen IC tag no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Spread/expansion of the radio frequency identification (RFID) system application technologies needs the international standards. In order to internationally promote spread/expansion of the RFID system application technologies, Japan has established the examination promotion organization with the participation of the advanced Japanese makers in development of the RFID technologies, representative application users of the distribution logistics and RFID technology standardization deliberative council. The elementary and application RFID technologies are studied and developed, and the results are demonstrated. The organization plans to propose the application requirement profile (ARP) specification drafts to WD (WI/18001) of the ARP, currently deliberated by ISO/IEC JTC1/SC31/WG4/ARP of International Standardization Organization. The organization also plans to submit the Air Interface specification drafts with frequencies of 125kHz and 2.54GHz to the WD (WI/18000) of JTC1/SC31/WG4/SG3. (NEDO)

Report on the results of the FY 1999 study on the standardization of the measuring/database method for data on human body shape characteristics; 1999 nendo shinki sangyo ikusei sokkogata kokusai hyojun kaihatsu jigyo. Shintai keitai tokusei data no keisoku database ka shuho ni kakawaru hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The purpose of the present project is to conduct studies on three-dimensional human body measurement; the method of describing measurement results; the method of developing a database using measurement data; and the method of statistical data processing. Results of these studies are to be used to establish an international standard on three-dimensional human shape data. In the course of the project, the state of relevant studies conducted outside Japan was investigated. As a result, it has been found that studies on the method of processing three-dimensional human body shape data are being promoted independently by different research institutes. At present, it is impossible to build up a consensus on the method among these institutes. Additionally, standardizing the method may stifle the creativity of researchers. We have therefore decided to exclude the standardization of body shape data processing method from the scope of the project. Our conclusion is that the standard proposed in the project should be based on the human body shape data format, obtained through a study on the method of describing three-dimensional body shape data. And it should provide for a data format for three-dimensional human body measurement, which can store all data required for product of space design (e.g. data on human body sizes, landmarks and texture). According to our plan, this standard will be proposed in the form of a technical report, since it is yet too early to se out establishing the standard as an international standard. (NEDO)

FY 1999 project on the development of new industry support type international standards. Standardization of methods to measure/evaluate characteristics of micro-machine use materials; 1999 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Micro machine yo zairyo no tokusei keisoku hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Study was conducted with the aim of developing the standard tensile test method which enables the measurement/evaluation of mechanical properties of various kinds of thin film materials with thickness of 10{mu}m or below and width of 100{mu}m or below and of making it a draft for the international standards. The FY 1999 results were summarized. As to the Round Robin Test, Si test pieces were so fabricated by bulk micro-machining that comparisons in testing method can easily be made. Concerning the test machine, the measurement of deformation and strain of test pieces at the time of tensile test was made possible with the introduction of an optical microscope with interferometer and CCD camera for image processing. The measurement was also made possible of Young' modulus of polycrystal Si films of test pieces different in length. Relating to the optimization of standard test pieces, basic tests were carried out on the analysis of gradients of sputter thin films/the trend of grain formation state, measurement of residual stress of Ni plated films, etc. In the survey of the adaptability to standardization, it was found out that industrial circles in Europe and the U.S. are not interested in the standardization which produces no direct profits. (NEDO)

Project in fiscal 2000 of developing international standards for supporting new industries. Standardization of method for evaluating mechanical stress of composite structures for aerospace use; 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Koku uchuyo sentan fukugozai no kyodo hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

R and D has been performed on methods to repair composite structures used in aerospace application, and on stress evaluation on repaired portions, targeting at establishment of international standardization. This paper summarizes the achievements in fiscal 2000. The current fiscal year has executed surveys on repair methods, selection of the repair methods, evaluation on the repairing processes, and compression strength evaluation on test samples given repairs. The method for repairing the sandwich-structure composite members was selected as a result surveys and discussions on published literatures. For the evaluation test on the repairing processes, specific repairing processes were established with reference to the result of surveys on the repair methods, which were applied to test samples having been given damages. In addition, discussions were given also on non-destructive inspection methods for sandwich panels. Regarding the strength test for repaired portions, a compression strength test was performed on test samples repaired by using adhesive after having been given damages, wherein data related to compression strength were obtained. Furthermore, a system was developed to analyze the scarf-like adhesive-repaired potions by using the two-dimensional finite element method model. (NEDO)

FY 2000 report on the results of the supplementary project for the development of energy utilization rationalization technology. Leading study for the development of high efficiency thermoelectric converter; 2000 nendo energy shiyo gorika gijutsu kaihatsu hojo jigyo seika hokokusho. Kokoritsu netsuden henkan soshi kaihatsu sendo kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-05-01

For the purpose of energy conservation and environmental protection by effective utilization of unused waste heat, the R and D of thermoelectric conversion technology were conducted, and the FY 2000 results were summed up. In the investigative study of thermoelectric converting materials, evaluation was made of the materials having a possibility of achieving the target with the element efficiency of 6% and the assumed use temperature domain of 120-330 degrees C. The result of the study indicated that the number of new materials which were made public was increasing, but there were no materials that have evidently practical applicability. In the investigative study of element manufacturing technology, trial manufacture of element was made in which the investigative results were integrated into the existing 50W element manufacturing technology, and a target of 70W was achieved. In the investigative study of the thermoelectric conversion system for industrial and commercial/residential use, field survey and questionnaire survey were conducted for three fields of iron works, chemical plant and garbage disposal plant. As a result, it was found that there was a large amount of waste heat. By the study of the system conceptional design, it was found out that the output of 40-50kW can be obtained in the system structure suitable for the source of waste heat of iron works, etc. (NEDO)

Achievement report in fiscal 1999 on commissioned research project. 'Model project for facilities to effectively utilize wastes from industrial complexes in Thailand' Project for 1999 Volume 2; 1999 nendo seika hokokusho. Tai ni okeru kogyo danchi sangyo haikibutsu yuko riyo setsubi moderu jigyo - 2

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With an objective to reuse industrial wastes and effectively utilize them as a petroleum replacing energy resource, and attempt to reduce consumption of fossil fuel in Thailand where increase in discharge of industrial wastes is estimated, a model project for facilities to effectively utilize wastes from industrial complexes has been carried out. This paper reports the achievements in fiscal 1999. Specifically, the project calls for incineration in fluidized bed incinerators of industrial wastes discharged from factories in industrial complexes possessed by the Industrial Estate Authority of Thailand (IEAT), recovery of waste heat from waste heat recovering boilers to generate process steam, which is supplied to the factories in the complexes. The current fiscal year, which is the first current year of the project, has put into order the operations shared by Japan and Thailand, compiled the various procedures and schedules into the form of appendices to the agreement, and executed signing of the agreement. Thereafter, the Japanese side has carried out decision on the specifications of the facilities, the basic designs, the detailed designs of facilities to be arranged by Japan, and the fabrication of some of the devices according to the descriptions of the agreement appendices. The volume 2 summarizes the inspection reports in the referential materials. (NEDO)

Fiscal 1999 technical achievement report. Research and development project on prompt-effect international standards creation (Standardization of test and evaluation of superhigh-precision toothed gear); 1999 nendo shinki sangyo ikusei sokkogata kokusai hyojun kaihatsu jigyo seika hokokusho. Choseimitsu haguruma no seidono shiken hyoka hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

In ISO1328 that covers specifications on precision of toothed gears, gears are graded according to the magnitude of error, but there is no system established for guaranteeing measured error values for accuracy. Activities are conducted for realizing such a guarantee, for establishing methods for testing and evaluating gear precision measuring devices, and for working out international standards for them. It is decided that the current status be investigated and then a concrete method be proposed as an international standard centering about gear precision measuring digital devices which will stay important in the future. A digital measuring device enhanced in precision is constructed by way of trial, and then it is proved that the newly fabricated device works effectively in the calibration of gear precision measuring devices in general use. Thanks to this process, basic data are collected about the measurement of gear precision using a gear precision measuring digital device, and this enables the preparation of a draft of criteria for international standardization. (NEDO)

FY 1999 Evaluation and analysis of the data collected by the field test project for photovoltaic power generation in public facilities. By site (1/3); 1999 nendo kokyo shisetsu nadoyo taiyoko hatsuden field test jigyo ni okeru shushu data hyoka kaiseki. 1/3. Kaku site betsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

Described herein are the results of evaluation and analysis of the data (management nos.701 to 814) collected by the field test project for photovoltaic power generation in a total of 45 facilities, mainly public. Each system is operated for 30 to 31 days every month. A total of 23 items of the data described below are recorded every day, and totaled up, averaged and evaluated for effectiveness at the end of the month: solar radiation on a horizontal, sloped and effective sloped plane, average air temperature, array electric energy, system electric energy, system power consumption, load electric energy, load for supplying power to a network, electric energy of reversed flow, linkage protection actions, linkage parallel off time, system operation time, self-sustaining load, load of voluntary supply, equivalent array operation, equivalent system operation, array output coefficient, system output coefficient, system utilization, system power generation efficiency, INV effective efficiency, and INV load factor. (NEDO)

Fiscal 1999 technical achievement report. Development project on prompt-effect international standards for developing new industry (Standardization of gene amplification and analysis methods for genetic screening); 1999 nendo shinki sangyo ikusei sokkogata kokusai hyojunka kaihatsu jigyo seika hokokusho. Idenshi kensayo idenshi zofuku kaiseki hoho no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

There is a move in Europe and America to establish their own standards for the polymerase chain reaction (PCR) technique although it is a technique essential to biotechnology, and it is feared that such will restrain Japan's activities. In its effort to counter the move, Japan is exerting its own endeavors, hoping that it will profit from international standardization of criteria for the PCR technique. The Japanese effort aims at establishing international standards by unifying measuring procedures in the PCR technique and by enhancing the general-purpose feature of the data involved. In concrete terms, items available on the market, such as test and research equipment, reagents, and electronic instruments for use in measurement, are compared with each other in terms of performance, and basic specifications necessary for standardization and basic data on quality are collected. The effort involves, in more concrete terms, the measurement of thermal cycler temperature distribution, the evaluation of heat-resistant DNA (deoxyribonucleic acid) polymerase temperature sensitivity and accuracy, and the evaluation of performance of CCD (charge coupled device) camera systems and Polaroid camera systems to be used for the evaluation of PCR products. (NEDO)

Report of FY 1997 on the international cooperation project. Survey of globalization of the effective energy resource utilization technology (development of high-accuracy acceleration measurement system); 1997 nendo kokusai kenkyu kyoryoku jigyo. Energy shigen yuko riyo gijutsu kenkyu kokusaika chosa (koseido kasokudo keisoku system no kaihatsu chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This report describes effectiveness of a system for measuring the acceleration and force in high accuracy by combining a laser interference meter and a vibration stand. A possibility of pressure sensitive paper to the impact force measurement in the collision examination is also described. The results obtained in FY 1997 are as follows. For the investigation of calibration system of acceleration and force sensor, one-dimensional interferometer system has been developed, which is standardized in ISO5347 accelerometer calibration. Thus, an interference fringe processing software has been made. Moreover, construction of a three-dimensional interferometer system has been started. For the characterization evaluation of pressure sensitive papers, it was succeeded in obtaining an elasticity wave pulse maximum about 1 msec by adopting the flight body made of resin. As a result, evaluation of the force sensor in the frequency area has become possible. To calculate the displacement of a body structural material in the collision experiment, an acceleration sensor has been made for trial purposes. For the international research cooperation, the working plan of a joint research with US Texas Christian University has been concluded. 11 refs., 73 figs., 23 tabs.

Achievement report for fiscal 1983 on Sunshine Program-entrusted survey and research. Cooperative project between Japan and Australia, etc., on solar energy technology (Cooperation between Japan and France on solar energy technology); 1983 nendo Nichigonado taiyo energy gijutsu kyoryoku jigyo seika hokokusho. Nichifutsu taiyo energy gijutsu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

1984-03-01

This paper reports a survey on solar heat utilization technologies conducted in fiscal 1983 in accordance with a scientific cooperation agreement signed by the Japanese Government and the French Government. The survey was carried out by two employees with the solar technology development office of the New Energy and Industrial Technology Development Organization who were dispatched to France on a tour in the period March 13-24. Concerning the 'French Photovoltaic Program 1982-1986,' knowledge on the goal of the program, long-term research and development, and budgetary matters were obtained at the AFME (French Energy Management Agency) head office and its branches. Relations of AFME with EC (European Community) projects were clarified. The photovoltaic power system (50kW) of Nice Airport is one of the EC projects, and was built thanks to financial aids by EC and AFME. The power system is now in service as a power source for electronic equipment in the airport management building and for taxi lights installed on the ground. The CGE (Compagnie General d'Electricite) central laboratory and the Rhone Poulenc Specialites Chimique were visited, when information on the research and development of a ribbon crystal pulling process and solar-grade silicon was acquired. (NEDO)

Summarized report on research cooperation promotion project in fiscal 2000. Research cooperation on developing high-efficiency mineral resource extracting and processing technology of environment harmonizing type; 2000 nendo kenkyu kyoryoku suishin jigyo sokatsu hokokusho. Kankyo chowagata kokoritsu kobutsushigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A joint research with the Republic of Kazakhstan has been carried out on developing a technology to extract and recover efficiently the valuable metals (copper, gold, silver and others) contained in ore wastes in large quantity produced in association with mine operation, with considerations given to the environment. This paper summarizes the achievements in fiscal 2000. The joint research has performed site survey for existence of ore wastes in the Republic of Kazakhstan, domestic research for discussing the disposal systems, design, fabrication, installation, adjustment and operation of a pilot plant. Process researches included ore flotation test, leaching test on Zhezkent ore wastes in chemical leaching and low-grade Nikolayevska ores, Cu leaching acceleration effect in bacteria leaching, utilization of activated carbon, fundamental test on solvent extraction, reverse extraction test, test using iron oxidizing bacteria in waste water treatment, Fe{sup 2}+ oxidation in waste water due to waste water bacteria concentrated by diatomaceous earth, Au and Ag leaching test, and column leaching test. This paper summarizes the results thereof. (NEDO)

Fiscal 1999 achievement report on the venture business assisting type regional consortium - Minor business creation base type. Development of simplified extraction/purification method for highly purified large-size plasmids; 1999 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. Kanbenka kojundo ogata plasmid chushutsu seiseiho no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The project aims to develop biotechnological industries in Okinawa Prefecture by embodying a method for obtaining large-size plasmids in a short time at low cost without a special apparatus, for which efforts were made to develop and commercialize a kit comprising an eluate from plasmid cells and a set of columns and eluate for purification. Under this project, University of the Ryukyus well experienced in the handling of plasmid DNAs and Advanced Medical Biological Science Institute jointly developed a 'simplified extraction/purification method for highly purified large-size plasmids.' The developed techniques or methods are described below. A concentration method was developed not using centrifugal operation for escherichia coli cultured in a closed mass culture device. A buffer exchange method in a closed system was developed, continuous from escherichia coli concentration to elution. A column assisted DNA purification method consuming but a short time was established. With these combined, the development is now complete of the technology and device for plasmid DNA elution from escherichia coli by an uninterrupted operation in a completely closed system. (NEDO)

FY 2000 Project of developing international standards for supporting new industries. Standardization of the marine environment analyzers (Analyzers for measuring CO2 in ocean); 2000 nendo shinki sangyo shiengata kokusai hyojun kaihatsu jigyo seika hokokusho. Kaiyo kankyo keisoku kiki (kaiyo CO2 sokutei kanren kikirui) no hyojunka

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Described herein are the FY 2000 results of the research and development of analyzers and analytical procedures necessary for evaluating CO2 abatement effects and fixed quantities in ocean, for proposing the international standards. The program for studying the analytical procedures makes a literature survey mainly on papers and also on patent publications, to collect the data related to this project and establish the database. The program for measuring CO2 in deep ocean studies a suspension type CO2 profiler with a liquid-liquid leveler and develops a small-size, high-precision device serviceable at a depth of 3,000m, around 1m in length and 40kg in weight. The program for flux meters tests various commercial sensors, to obtain the design requirements for the sensor of improved functions to withstand splashes and rolling/pitching. The program for CO2 flux measurement methods study aims at the eddy correlation method, which is the most direct procedure involving limited number of assumptions, after having investigated various procedures, to improve precision of the sensor. (NEDO)

FY 2000 report on the results of the project for measures for rationalization of the international energy utilization - the model project for the heightening of efficiency of the international energy consumption. 2/2. Model project for facilities for effective utilization of by-producing exhaust gases from chemical plant, etc.; 2000 nendo kokusai energy shohi koritsuka tou moderu jigyo seika hokokusho. Kagaku kojo fukusei haigasu tou yuko riyo setsubi moderu jigyo (2/2)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of contributing to the reduction in the energy consumption in China and the stable energy supply in Japan by heightening efficiency of the energy utilization in the petrochemical industry which is an industry of much energy consumption in China, a model project for facilities for effective utilization of by-producing gases from chemical plant, etc. was carried out, and the FY 2000 results were reported. Concretely, the combustion incinerator and combustion exhaust gas recovery facilities for waste water and gas were to be installed at acrylonitrile plant of petrochemical plant in China to recover the combustion exhaust gas as process gas used in plant for effective utilization. In this fiscal year, the detailed design and supply of electric instrumentation equipment and manufacture of boiler facilities were carried out according to the basic design made in the previous fiscal year. Further, the equipment manufactured in the previous year and this fiscal year were transported and inspected. The paper also reviewed drawings of the design of the facilities for part of which China takes responsibility. The separate volume (2/2) included drawings of valve, fire detector, orifice, thermocouple, motor control equipment, etc. (NEDO)

FY 2000 report on the results of the project for measures for rationalization of the international energy utilization - the model project for the heightening of efficiency of the international energy consumption. 1/2. Model project for facilities for effective utilization of by-producing exhaust gases from chemical plant, etc.; 2000 nendo kokusai energy shohi koritsuka tou moderu jigyo seika hokokusho. Kagaku kojo fukusei haigasu tou yuko riyo setsubi moderu jigyo (1/2)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of contributing to the reduction in the energy consumption in China and the stable energy supply in Japan by heightening efficiency of the energy utilization in the petrochemical industry which is an industry of much energy consumption in China, a model project for facilities for effective utilization of by-producing gases from chemical plant, etc. was carried out, and the FY 2000 results were reported. Concretely, the combustion incinerator and combustion exhaust gas recovery facilities for waste water and gas were to be installed at acrylonitrile plant of petrochemical plant in China to recover the combustion exhaust gas as process gas used in plant for effective utilization. The plant at installation site has been run since 1995, having a production capacity of 50,000-60,000 tons. In this fiscal year, the detailed design and supply of electric instrumentation equipment and manufacture of boiler facilities were carried out according to the basic design made in the previous fiscal year. Further, the equipment manufactured in the previous year and this fiscal year were transported and inspected. The paper also reviewed drawings of the design of the facilities for part of which China takes responsibility. (NEDO)

FY1995 evolvable hardware chip; 1995 nendo shinkasuru hardware chip

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This project aims at the development of 'Evolvable Hardware' (EHW) which can adapt its hardware structure to the environment to attain better hardware performance, under the control of genetic algorithms. EHW is a key technology to explore the new application area requiring real-time performance and on-line adaptation. 1. Development of EHW-LSI for function level hardware evolution, which includes 15 DSPs in one chip. 2. Application of the EHW to the practical industrial applications such as data compression, ATM control, digital mobile communication. 3. Two patents : (1) the architecture and the processing method for programmable EHW-LSI. (2) The method of data compression for loss-less data, using EHW. 4. The first international conference for evolvable hardware was held by authors: Intl. Conf. on Evolvable Systems (ICES96). It was determined at ICES96 that ICES will be held every two years between Japan and Europe. So the new society has been established by us. (NEDO)

Electrical properties of smectites; Smectite nendo kobutsu no denkiteki bussei

Energy Technology Data Exchange (ETDEWEB)

Takakura, S; Nishizawa, O; Aoki, M [Geological Survey of Japan, Tsukuba (Japan); Kozake, K [University of Tsukuba, Tsukuba (Japan)

1997-05-27

With an objective to evaluate effects of clayish minerals in the electric and electromagnetic exploration methods, resistivities were measured on samples which have adjusted contents of clayish minerals. Samples were prepared for an experiment by mixing 300 g of glass beads having a diameter of about 1 mm, 200 g of aqueous solutions, and 3 to 90 g of smectites. The aqueous solutions used KCL, NaCL and CaCL2 at concentrations of 0.1 to 0.001 mol/L. The result of the experiment may be summarized as follows: among the three kinds of smectites, KN-1 has the greatest effect to reduce the resistivity; the resistivity decreases when the smectite amount is increased except when the concentration of the solution is high; this phenomenon is thought to be caused by increase in the region of an electrically doubled layer which has higher ion concentration; change in the resistivity increases when the solution concentration is low, and decreases when the concentration is high; and in the case of the solution concentration being 0.1 mol/L, the resistivity increases with increase in the smectite content. 5 refs., 7 figs., 1 tab.

FY1995 evolvable hardware chip; 1995 nendo shinkasuru hardware chip

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This project aims at the development of 'Evolvable Hardware' (EHW) which can adapt its hardware structure to the environment to attain better hardware performance, under the control of genetic algorithms. EHW is a key technology to explore the new application area requiring real-time performance and on-line adaptation. 1. Development of EHW-LSI for function level hardware evolution, which includes 15 DSPs in one chip. 2. Application of the EHW to the practical industrial applications such as data compression, ATM control, digital mobile communication. 3. Two patents : (1) the architecture and the processing method for programmable EHW-LSI. (2) The method of data compression for loss-less data, using EHW. 4. The first international conference for evolvable hardware was held by authors: Intl. Conf. on Evolvable Systems (ICES96). It was determined at ICES96 that ICES will be held every two years between Japan and Europe. So the new society has been established by us. (NEDO)

FY 1985-1992 summarized report on the R and D of photoreactive materials; 1985 nendo kara 1992 nendo hikari hanno zairyo kenkyu kaihatsu sokatsu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-12-01

For the purpose of establishing the basement technology relating to photoreactive materials which make remarkably higher density and larger capacity of the information recording possible, the following were made for photochromic materials and PHB materials: elucidation of the photoreaction mechanism, development of materials, development of material processing/structure technology and development of evaluation technology. The target is to establish the technology of the multiplex recording which is applicable to the super-high density recording in relation to PHB materials/organic photochromic materials which have potentiality of photon-mode recording. PHB materials were developed which have potentiality of 600 wavelength multiple recording and 5 electric field multiple recording in 4.2K and 9 wavelength multiple recording in 77K. Photochromic materials were developed which have high sensitivity and preservation stability and have potentiality of 10 wavelength multiple recording at room temperature. A new photo-recording method was found out by which the orientation of liquid crystal is photo-controlled and potentiality of the multiple polarization was shown. Moreover, the fabrication was successfully made of PHB materials and photochromic materials which make non-destructive readout operation of more than 10{sup 4} times possible. (NEDO)

FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D field. Third year report. R and D of a working material processing eco system using powder mold-releasing lubricant; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu bun'ya. Funtai rigata junkatsuzai wo mochiita sokeizai kako eco system no kenkyu kaihatsu (dai 3 nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of constructing the industry of processing low cost/low environmental load working materials, the development was proceeded with of a block die type powder mold-releasing system. Studies were made in the following 6 fields: 1) optimization/commercialization of new adhesion/flow methods; 2) optimization/commercialization of new powder mold-releasing lubricant; 3) demonstrative experiment and optimization of an eco die cast system; 4) optimization of a powder mold-releasing forging system; 5) application test on the actual mold-releasing lubricant reduction type system; 6) comprehensive investigational study. In 1), studied were a method to integrate the profile of supply pressure of powder conveying air flow and the basic information on adhesion behavior into the practical process, and optimization of powder supply method and supply device control sequence. In 2), the development was made of a sleeve use high thermal insulation type powder mold-releasing lubricant (composed mostly of Al(OH){sub 3}, graphite and wax). This powder mold-releasing lubricant remarkably improved forging ability of the ultra-thin material with 0.4mm thickness and materials with complex shapes and markedly decreased fracture chills. (NEDO)

FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D field. First year report. Development of the production technology of clean hydrogen, etc. by direct methane reforming method; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu bun'ya. Methane chokusetsu kaishitsuho ni yoru clean suiso nado no seizo gijutsu kaihatsu (dai 1 nendo) seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

The development was proceeded with of the hydrogen production method using the zeolite-base methane dehydrogenation cyclization catalyst with the specific porous structure. In this production method, there is no emission of process CO2, and hydrogen can be produced by supply of energy of 1/10 of that in the conventional technology. In FY 2000, the following were conducted: 1) conceptual design of a demonstrative experiment plant; 2) development of catalyst processing technology; 3) development of element technology such as improvement of catalyst performance. In 1), design/specifications for demonstrative experiment use plant were fixed by design estimation and process analysis using the mid-term fluidized bed experiment device. It was decided that the mid-term fluidized bed experiment device will be constructed to evaluate the methane reforming performance of catalyst and that the reaction tower should be the stationary fluidized bed type. In 2), a catalyst activity experimental device 100 times as large as the laboratory was fabricated to evaluate the catalyst performance. By optimization of reaction conditions and preparation of the catalyst composition, the targeted catalyst system was obtained. (NEDO)

Global environmental problems in the electric industry. Denki jigyo ni okeru chikyu kankyo mondai ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Sugi, T [Tokyo Electric Power Co., Inc. (Japan)

1992-09-30

Since the electric industry has grappled with a prevention of the environmental pollution such as the air pollution and water contamination as a forerunner in case of construction and operation of the power facilities, and at the same time has conducted actively the environmental conservation countermeasures, it has consequently achieved the environmental conservation level as a top level in the world. On the other hand, as for the emission quantity of CO2 relating to the earth warming, the power field occupies about one fourth of total Japan. Therefore the electric industry should aim at the electric energy supply considering the influence on the environment, such as the power supply structure to restrain CO2 emission as less as possible, higher efficiency of equipments, higher efficiency of energy utilization by using the unused energy and so forth. In addition to it, the consumer side should aim at the social structure with a recycle type such as saving resources and saving energy, and aim at changeover of life style. It is hoped to conduct the overall measure including the items mentioned above. In this report, the recent trend of earth enviromental problems, grappling with the environmental problems as a forerunner such as the prevention measure of air pollution in the thermal power plant, etc., and the correspondence to the earth warming problems are outlined. 11 refs., 9 figs., 3 tabs.

Fiscal 1995 survey report on the environmentally friendly type coal utilization system joint demonstration project. Water-saving coal preparation system joint demonstration project; Kankyo chowagata sekitan riyo system kyodo jissho jigyo. Shosuigata sentan system kyodo jissho jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This project makes demonstration of clean coal technology (CCT) in China and preparation for the base of its spread, controlled environmental pollution due to the coal use by the countries concerned, and contributes to stably secure energy of Japan. The paper made analog operation in the 1960s-1970s, supported by Russia and Poland, introduced two computer systems for operational control and quality control, densimeter, level meter, flow meter and analyzer to coal preparation plants having problems on productivity and quality control, made the optimum operational diagnosis for the plants, and at the same time, demonstrated the comprehensive rehabilitation type system by which water saving, high quality and high effectiveness are obtained. Various types of sensors such as rapid ash meter, scale and densitometer and computers are introduced to coal preparation plants which were recently constructed in China, have jig or heavy liquid cyclone as main preparation equipment and conducts operational control. There, the central control system was demonstrated in which various information collected in the central operation room and in-site equipment is combined by network for high-grade data processing and water saving is achieved. 50 figs., 11 tabs.

Research program for environmentally-friendly coal utilization system. Follow-up project for simplified desulfurizers (Weifang Chemical Industry Works); Kankyo chowagata sekitan riyo system donyu shien jigyo. Kan`i datsuryu setsubi ni kakawaru follow up jigyo (Weifang kakosho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

To suppress the emission of environmental pollutants from coal utilization in China and to contribute to stable security of Japan`s energy, demonstration of clean coal technology and consolidation of diffusion base to be introduced into China have been promoted. Demonstration program for diffusing simplified desulfurizers has been promoted. For accelerating the achievement, experts of desulfurizers were delegated to Weifang Chemical Industry Works, to support the program. Exhaust gas is introduced from boiler via water spray dust remover, suction fan and centralized stack into absorption tower of the simplified wet-type desulfurizer. In the ascending process, the exhaust gas contacts with absorbent, to remove SO2 and dust. The absorbent is blasted up through the spray nozzle. The absorbent is oxidized by the air into sulfate ion in the liquid chamber at the lower part of tower, and neutralized by hydrated lime to form gypsum. Through the continuous operation for two years, understandings were remarkably increased. However, good treatment of the tax system is required for further diffusion. Though there are no problems for ordinary start and stop, emergency operation is insufficient. There are some problems in the maintenance due to the delay of finding failures. 16 figs., 1 tab.

Basic investigation project for energy consumption efficiency improvement in developing countries. Invitation of engineers from developing countries (Vietnam, Philippines, and India); Hatten tojokoku energy shohi koritsuka kiso chosa nado jigyo. Hatten tojokoku gijutsusha shohei jigyo (Betonamu, Philippines, Indo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The International Center of Environmental Technology Transfer has invited seven engineers from Vietnam, eight from Philippines and two from India for human resource education project for environmental preservation in developing countries. Those who were invited are administrative officials and engineers who work at administrative agents, research institutes and corporations related to energy conservation and environment preservation. In this invitation program, lecturers were invited from governmental offices, universities and corporations according to their expertise fields to carry out lectures and site training. With respect to energy conservation, lectures were given on a `summary of energy saving methods` by a lecturer invited from the Chubu Governmental Department of Trade and Industry, and on an `introduction to new energies` by Prof. Shimizu at the Engineering Faculty of the Mie University. Both lecturers emphasized the necessity of energy conservation, and importance of new energies as clean energies. The trainees showed strong interest when they visited a `cement factory` and a `coal burning thermal power plant` as the key industries. Their experience would be reflected strongly on guiding operations of factories in their own countries. 56 figs., 15 tabs.