WorldWideScience

Sample records for neg pumping strip

  1. NEG pumps can go to the extremes

    CERN Multimedia

    Manini, Paolo

    2004-01-01

    Non-evaporable getters are highly reactive materials, generally made of zirconium or titanium; NEG pumps are efficient and clean sinks for molecules and they regularly achieve pressures as low as 10¯11, or even 10¯13 mbar (½ page)

  2. A Strip-Type Microthrottle Pump: Modeling, Design and Fabrication

    Directory of Open Access Journals (Sweden)

    Dejan Križaj

    2013-03-01

    Full Text Available A novel design for a strip-type microthrottle pump with a rectangular actuator geometry is proposed, with more efficient chip surface consumption compared to existing micropumps with circular actuators. Due to the complex structure and operation of the proposed device, determination of detailed structural parameters is essential. Therefore, we developed an advanced, fully coupled 3D electro-fluid-solid mechanics simulation model in COMSOL that includes fluid inertial effects and a hyperelastic model for PDMS and no-slip boundary condition in fluid-wall interface. Numerical simulation resulted in accurate virtual prototyping of the proposed device only after inclusion of all mentioned effects. Here, we provide analysis of device operation at various frequencies which describes the basic pumping effects, role of excitation amplitude and backpressure and provides optimization of critical design parameters such as optimal position and height of the microthrottles. Micropump prototypes were then fabricated and characterized. Measured characteristics proved expected micropump operation, achieving maximal flow-rate 0.43 mL·min−1 and maximal backpressure 12.4 kPa at 300 V excitation. Good agreement between simulation and measurements on fabricated devices confirmed the correctness of the developed simulation model.

  3. Non evaporable getter (NEG) technology: A powerful tool for UHV-XHV systems

    Science.gov (United States)

    Maccallini, Enrico; Siviero, Fabrizio; Bonucci, Antonio; Conte, Andrea; Srivastava, Peeyush; Paolo, Manini

    2012-06-01

    Ultra and Extreme High Vacuum (UHV and XHV respectively) levels are needed in several vacuum-related applications for wide pressure and time range. The Non Evaporable Getter (NEG) technology is one of the most important examples to get XHV/UHV condition in the vacuum systems. In fact the high reactivity of the getter materials towards active gases in a wide temperature range (from room temperature to several hundreds of °C) allows removing very efficiently active gases such as H2, H2O, CO2, CO, N2, and so on. When declining, the pumping speed of NEG can be easily restored, by reactivating the getter material with a thermal process ("reactivation"). In this framework, SAES Getters S.p.A. has a long expertise in producing NEG pumps (and more in general NEG technology) which can provide vacuum conditions from the low to the ultra high level. An overall overview of NEG pump technology will be given in this paper considering 1) the involved mechanisms for gas adsorption into the NEG material, 2) operational conditions of NEG pumps and 3) example of applications which demonstrate the benefits of NEG pumps use in XHV/UHV systems. Future perspectives for NEG pumps in UHV/XHV applications will be also given.

  4. NEG-shift, Licensing, and Repair Strategies

    DEFF Research Database (Denmark)

    Christensen, Ken Ramshøj

    2008-01-01

    I entertain the idea that the cross-linguistic variation in the licensing of NEG-shift, the movement of negative objects to spec-NegP, can be accounted for by a few representational constraints that are not directly related to case licensing or feature checking, and which potentially conflict wit...

  5. NEG-shift, Licensing, and Repair Strategies

    DEFF Research Database (Denmark)

    Christensen, Ken Ramshøj

    2008-01-01

    I entertain the idea that the cross-linguistic variation in the licensing of NEG-shift, the movement of negative objects to spec-NegP, can be accounted for by a few representational constraints that are not directly related to case licensing or feature checking, and which potentially conflict wit...

  6. Status of NEG Coating at ESRF

    CERN Document Server

    Hahn, Michael

    2005-01-01

    The ESRF non-evaporable getter (NEG) coating facility is in operation since two years now. A large part of the insertion device straight sections of the electron storage ring has been equipped with in-house coated 5m long aluminum vacuum chambers with an inner vertical aperture of 8 mm. Operational experience with different coating parameters leading to different film thicknesses will be given and compared to bremsstrahlung data. The paper deals also with improvements of the coating production and chamber preparation, and describes some aspects of NEG coating data acquisition, visualization, and remote control. The R&D program leading to a more powerful DC solenoidal coating tool to further improve the NEG coating production throughput and quality aspects is also discussed.

  7. 33 CFR 157.128 - Stripping system.

    Science.gov (United States)

    2010-07-01

    ... of the following devices for stripping oil from each cargo tank: (1) A positive displacement pump. (2) A self-priming centrifugal pump. (3) An eductor (4) Any other device accepted by the Commandant. (d... positive displacement pump or a self-priming centrifugal pump, the stripping system must have the...

  8. The Acquisition of Neg-V and V-Neg Order in Embedded Clauses in Swedish: A Microparametric Approach

    Science.gov (United States)

    Waldmann, Christian

    2014-01-01

    This article examines the acquisition of embedded verb placement in Swedish children, focusing on Neg-V and V-Neg order. It is proposed that a principle of economy of movement creates an overuse of V-Neg order in embedded clauses and that the low frequency of the target-consistent Neg-V order in child-directed speech obstructs children from…

  9. Redox magnetohydrodynamics enhancement of stripping voltammetry of lead(II), cadmium(II) and zinc(II) ions using 1,4-benzoquinone as an alternative pumping species.

    Science.gov (United States)

    Ensafi, Ali A; Nazari, Z; Fritsch, I

    2012-01-21

    Differential pulse anodic stripping voltammetry (DPASV) coupled with redox-magnetohydrodynamics (MHD) is used to enhance the anodic stripping voltammetry (ASV) response using a mercury thin film-glassy carbon electrode. The sensitivity increased to at least a factor of two (at 1.2 T) and is facilitated by using 20.0 mmol L(-1) 1,4-benzoquinone as an alternative pumping species to enhance ASV by redox-MHD. The MHD force formed by the cross-product of ion flux with magnetic field induces solution convection during the deposition step, enhancing mass transport of the analytes to the electrode surface and increasing their preconcentrated quantity in the mercury thin film. Therefore, larger ASV peaks and improved sensitivities are obtained, compared with analyses performed without a magnet. The influence of pH, 1,4-benzoquinone concentration, accumulation potential, and time are also investigated. Detection limits of 0.05, 0.09 and 2.2 ng mL(-1) Cd(II), Pb(II) and Zn(II) were established with an accumulation time of 65 s. The method is used for the analysis of Cd(II), Pb(II) and Zn(II) in different water samples, certified reference materials, and saliva samples with satisfactory results.

  10. PUMPS

    Science.gov (United States)

    Thornton, J.D.

    1959-03-24

    A pump is described for conveving liquids, particure it is not advisable he apparatus. The to be submerged in the liquid to be pumped, a conduit extending from the high-velocity nozzle of the injector,and means for applying a pulsating prcesure to the surface of the liquid in the conduit, whereby the surface oscillates between positions in the conduit. During the positive half- cycle of an applied pulse liquid is forced through the high velocity nozzle or jet of the injector and operates in the manner of the well known water injector and pumps liquid from the main intake to the outlet of the injector. During the negative half-cycle of the pulse liquid flows in reverse through the jet but no reverse pumping action takes place.

  11. New continuous air pumping technique to improve clinical outcomes of descemet-stripping automated endothelial keratoplasty in asian patients with previous ahmed glaucoma valve implantation.

    Directory of Open Access Journals (Sweden)

    Chang-Min Liang

    Full Text Available BACKGROUND: To evaluate the outcomes of Descemet-stripping automated endothelial keratoplasty (DSAEK with the use of continuous air pumping technique in Asian eyes with previous Ahmed glaucoma valve implantation. METHODS: The DSAEK procedure was modified in that complete air retention of the anterior chamber was maintained for 10 min using continuous air pumping at 30 mm Hg. The primary outcome measurement was graft survival, and postoperative clinical features including, rate of graft detachment, endothelial cell count, intraocular pressure (IOP, surgical time and cup/disc ratio were also recorded. RESULTS: A total of 13 eyes of 13 patients which underwent modified DSAEK and 6 eyes of 6 patients which underwent conventional DSAEK were included. There was a significant difference in graft survival curves between two groups (P = 0.029; the 1-year graft survival rates were estimated as 100% and 66.7% for patients with modified DSAEK and those with traditional DSAEK, respectively. The rate of graft detachment were 0% and 33.3% for the modified DSAEK and conventional DSAEK groups, respectively (P = 0.088. The significantly lowered surgical time for air tamponade was noted in the modified DSAEK group compared to that in the conventional DSAEK group [median (IQR: 10.0 (10.0, 10.0 min vs. 24.5 (22.0, 27.0 min; P<0.001] Postoperatively, patients in the modified DSAEK group had significantly lower IOP as compared to the conventional DSAEK group [12.0 (11.0, 15.0 mm Hg vs. 16.0 (15.0, 18.0 mm Hg; P = 0.047]. Modified DSAEK patients had higher endothelial cell counts as compared to conventional DSAEK patients [2148.0 (1964.0, 2218.0 vs. 1529.0 (713.0, 2014.0], but the difference did not reach statistical significance (P = 0.072. CONCLUSIONS: New continuous air pumping technique in DSAEK can be performed safely and effectively in patients with prior GDDs placement who have corneal failure.

  12. Low-cost, high-performance nonevaporable getter pumps using nonevaporable getter pills

    Energy Technology Data Exchange (ETDEWEB)

    Kodama, Hiraku; Ohno, Shinya; Tanaka, Masatoshi [Faculty of Engineering, Yokohama National University, 79-5 Tokiwadai, Hodogaya-ku, Yokohama 240-8501 (Japan); Tanaka, Masato; Okudaira, Koji K. [Faculty of Engineering, Chiba University, 1-33 Yayoi-cho, Inage-ku 263-8522 (Japan); Mase, Kazuhiko, E-mail: mase@post.kek.jp; Kikuchi, Takashi [Institute of Materials Structure Science, KEK, 1-1 Oho, Tsukuba 305-0801 (Japan)

    2016-09-15

    Nonevaporable getter (NEG) pumps are widely used for maintaining a clean ultrahigh vacuum (UHV) of ≤10{sup −8 }Pa because of their high pumping speeds for hydrogen (H{sub 2}) and active gases in the UHV region. In addition, they are oil free, evaporation free, sputtering free, sublimation free, magnetic field free, vibration free, economical, compact, lightweight, and energy saving. In the present paper, the authors report a new NEG pump which is composed of commercial 60 NEG pills (ϕ10 × 3 mm; 70 wt. % Zr, 24.6 wt. % V, and 5.4 wt. % Fe), titanium parts, a DN 40 conflat flange, and a tantalum heater. The NEG pills are vertically and radially aligned around the heater to maximize the effective area for pumping. After activation at 400 °C for 30 min, the pumping speeds of the NEG pump were measured with the orifice method. Pumping speeds of 140–130, 200–140, 190–130, and 35–17 l/s were estimated for H{sub 2}, CO, CO{sub 2}, and N{sub 2} gasses, respectively, in a pumped-quantity range of 0.01–0.1 Pa l. Since the NEG pump is composed of a heating unit and a NEG module, the pumping speeds can be improved by increasing the number of NEG modules. These NEG pumps are favorable alternatives to sputtering ion pumps or titanium sublimation pumps.

  13. "AB neg AB"格式之再探

    Institute of Scientific and Technical Information of China (English)

    马凤霞

    2009-01-01

    "AB neg AB"格式松散,变化形式多样.正因如此,研究界关于这一格式的争论很多,还有很多悬而未决的问题.本文主要就以下两个问题作一些探索性研究:一、"A neg AB"格式的规范性问题;二、"AB negAB"格式中AB与各类词的相容性问题.

  14. Trabalho, Lazer e Turismo de Negócios

    Directory of Open Access Journals (Sweden)

    Jorge Marques

    2012-12-01

    Full Text Available As viagens motivadas pelos negócios e profissões referem-se a uma das mais antigas formas de viajar, tendo a sua evolução ocorrido ao longo dos tempos à medida que as sociedades se foram transformando económica e socialmente. Hoje em dia, não só falamos de viagens de negócios como também de Turismo de Negócios que, para muitos destinos, representa um importante setor económico. Com este trabalho pretende-se fazer uma breve análise à evolução dos conceitos de trabalho, lazer e viagens de negócios ao longo dos últimos séculos, de modo a melhor compreendermos este fenómeno relativamente recente.

  15. Development of NEG Coating for RHIC Experimental Beamtubes

    CERN Document Server

    Weiss, Daniel; Hseuh Hsiao Chaun; Todd, Robert J

    2005-01-01

    As RHIC beam intensity increases beyond original scope, pressure rises in some regions have been observed. The luminosity limiting pressure rises are associated with electron multi-pacting, electron stimulated desorption and beam induced desorption. Non-Evaporable Getter (NEG) coated beampipes have been proven effective to suppress pressure rise in synchrotron radiation facilities. Standard beampipes have been NEG coated by a vendor and added to many RHIC UHV regions. BNL is developing a cylindrical magnetron sputtering system to NEG coat special beryllium beampipes installed in RHIC experimental regions. It features a hollow, liquid cooled cathode producing power density of 500W/m and deposition rate of 5000 Angstrom/hr on 7.5cm OD beampipe. The cathode, a titanium tube partially covered with zirconium and vanadium ribbons, is oriented for horizontal coating of 4m long chambers. Ribbons and magnets are arranged to provide uniform sputtering distribution and deposited NEG composition. Vacuum performance of NE...

  16. slice of LEP beamtube with getter strip

    CERN Multimedia

    1989-01-01

    A section of the LEP beam pipe. This is the chamber in which LEP's counter-rotating electron and positron beams travel. It is made of lead-clad aluminium. The beams circulate in the oval cross-section part of the chamber. In the rectangular cross-section part, LEP's innovative getter-strip vacuum pump is installed. After heating to purify the surface of the getter, the strip acts like molecular sticky tape, trapping any stray molecules left behind after the accelerator's traditional vacuum pumps have done their job.

  17. The Strip Module

    DEFF Research Database (Denmark)

    Pedersen, Tommy

    1996-01-01

    -ship code available at the department. It will be structured as a general preprocessor mainly to determine the hydrodynamic mass and damping. A strip processor including three different theories: A linear frequency domain strip theory, a quadratic strip theory and a nonlinear time domain strip theory...

  18. “AB neg AB”格式之再探

    Institute of Scientific and Technical Information of China (English)

    马凤霞

    2009-01-01

    “AB neg AB”格式松散,变化形式多样。正因如此,研究界关于这一格式的争论很多,还有很多悬而未决的问题。本文主要就以下两个问题作一些探索性研究:一、“A neg AB”格式的规范性问题;二、“AB neg AB”格式中AB与各类词的相容性问题。

  19. Panorama dos modelos de negócios emerg entes da tv digital aberta

    OpenAIRE

    Felippe Souza de Lima; Danilo Leme Bressan; Francisco Rolfsen Belda; Gisleine Fátima Durigan; Matheus Monteiro de Lima

    2015-01-01

    O presente artigo tem como objetivo descrever modelos de negócios emergentes aplicados àTV digital aberta. A partir de uma pesquisa exploratória, o trabalho apresenta a atual realidadeda televisão aberta e seus modelos de negócios. Posteriormente, é feito um mapeamentopanorâmico buscando, assim, novas oportunidades de geração de receitas em negócio decomunicação audiovisual, considerando novos recursos tecnológicos que foramproporcionados pela digitalização da televisão aberta. Por fim, são a...

  20. Approximate strip exchanging.

    Science.gov (United States)

    Roy, Swapnoneel; Thakur, Ashok Kumar

    2008-01-01

    Genome rearrangements have been modelled by a variety of primitives such as reversals, transpositions, block moves and block interchanges. We consider such a genome rearrangement primitive Strip Exchanges. Given a permutation, the challenge is to sort it by using minimum number of strip exchanges. A strip exchanging move interchanges the positions of two chosen strips so that they merge with other strips. The strip exchange problem is to sort a permutation using minimum number of strip exchanges. We present here the first non-trivial 2-approximation algorithm to this problem. We also observe that sorting by strip-exchanges is fixed-parameter-tractable. Lastly we discuss the application of strip exchanges in a different area Optical Character Recognition (OCR) with an example.

  1. Panorama dos modelos de negócios emerg entes da tv digital aberta

    Directory of Open Access Journals (Sweden)

    Felippe Souza de Lima

    2015-12-01

    Full Text Available O presente artigo tem como objetivo descrever modelos de negócios emergentes aplicados àTV digital aberta. A partir de uma pesquisa exploratória, o trabalho apresenta a atual realidadeda televisão aberta e seus modelos de negócios. Posteriormente, é feito um mapeamentopanorâmico buscando, assim, novas oportunidades de geração de receitas em negócio decomunicação audiovisual, considerando novos recursos tecnológicos que foramproporcionados pela digitalização da televisão aberta. Por fim, são apresentados casos,demonstrando maneiras adotadas por emissoras televisivas para gerar conteúdo adicionalmultiplataforma e desdobramentos estratégicos desenvolvidos para captar receitas por meiodestes modelos de negócios emergentes.

  2. The Strip Module

    DEFF Research Database (Denmark)

    Pedersen, Tommy

    1996-01-01

    When the behaviour of a ship in waves is to be predicted it is convenient to have a tool which includes different approaches to the problem.The aim of this project is to develop such a tool named the strip theory module. The strip theory module will consist of submodules dependent on the I......-ship code available at the department. It will be structured as a general preprocessor mainly to determine the hydrodynamic mass and damping. A strip processor including three different theories: A linear frequency domain strip theory, a quadratic strip theory and a nonlinear time domain strip theory...

  3. The water crisis in the gaza strip: prospects for resolution.

    Science.gov (United States)

    Weinthal, E; Vengosh, A; Marei, A; Kloppmann, W

    2005-01-01

    Israel and the Palestinian Authority share the southern Mediterranean coastal aquifer. Long-term overexploitation in the Gaza Strip has resulted in a decreasing water table, accompanied by the degradation of its water quality. Due to high levels of salinity and nitrate and boron pollution, most of the ground water is inadequate for both domestic and agricultural consumption. The rapid rate of population growth in the Gaza Strip and dependence upon ground water as a single water source present a serious challenge for future political stability and economic development. Here, we integrate the results of geochemical studies and numerical modeling to postulate different management scenarios for joint management between Israel and the Palestinian Authority. The chemical and isotopic data show that most of the salinity phenomena in the Gaza Strip are derived from the natural flow of saline ground water from Israel toward the Gaza Strip. As a result, the southern coastal aquifer does not resemble a classic "upstream-downstream" dispute because Israel's pumping of the saline ground water reduces the salinization rates of ground water in the Gaza Strip. Simulation of different pumping scenarios using a monolayer, hydrodynamic, two-dimensional model (MARTHE) confirms the hypothesis that increasing pumping along the Gaza Strip border combined with a moderate reduction of pumping within the Gaza Strip would improve ground water quality within the Gaza Strip. We find that pumping the saline ground water for a source of reverse-osmosis desalination and then supplying the desalinated water to the Gaza Strip should be an essential component of a future joint management strategy between Israel and the Palestinian Authority.

  4. Varicose vein stripping

    Science.gov (United States)

    ... vein stripping; Venous reflux - vein stripping; Venous ulcer - veins Images Circulatory system References American Family Physician. Management of varicose veins. www.aafp.org/afp/2008/1201/p1289.html . ...

  5. M-Business: Negócios, Tecnologias e Estratégias

    Directory of Open Access Journals (Sweden)

    Luiz Claudio Gonçalves

    2013-12-01

    Full Text Available As tecnologias de comunicação sem fio (wireless, irreversivelmente estão surgindo nos atuais ambientes de negócios. Facilidades como ubiqüidade e amigabilidade no uso fazem a sua aceitação ser praticamente imediata para usuários, desenvolvedores e profissionais de modelagem de negócios. Essas tecnologias despontam como a solução operacional, econômica e estratégica do século XXI e, segundo as previsões dos institutos de pesquisa, o volume de negócios gerados epas mesmas serão sensivelmente expressivos. Desse modo, o presente artigo, por meio de uma pesquisa bibliográfica e um estudo de caso busca apresentar e avaliar os impactos do m-business nas operações das empresas modernas

  6. High frequency electromagnetic characterization of NEG properties for the CLIC damping rings

    CERN Document Server

    Koukovini-Platia, E; Zannini, C

    2014-01-01

    Coating materials will be used in the CLIC damping rings (DR) to suppress two-stream effects. In particular, NEG coating is necessary to suppress fast beam ion instabilities in the electron damping ring (EDR). The electromagnetic (EM) characterization of the material properties up to high frequencies is required for the impedance modeling of the CLIC DR components. The EM properties for frequencies of few GHz are determined with the waveguide method, based on a combination of experimental measurements of the complex transmission coefficient S21 and CST 3D EM simulations. The results obtained from a NEG-coated copper (Cu) waveguide are presented in this paper.

  7. Anatomy Comic Strips

    Science.gov (United States)

    Park, Jin Seo; Kim, Dae Hyun; Chung, Min Suk

    2011-01-01

    Comics are powerful visual messages that convey immediate visceral meaning in ways that conventional texts often cannot. This article's authors created comic strips to teach anatomy more interestingly and effectively. Four-frame comic strips were conceptualized from a set of anatomy-related humorous stories gathered from the authors' collective…

  8. Science Comic Strips

    Science.gov (United States)

    Kim, Dae Hyun; Jang, Hae Gwon; Shin, Dong Sun; Kim, Sun-Ja; Yoo, Chang Young; Chung, Min Suk

    2012-01-01

    Science comic strips entitled Dr. Scifun were planned to promote science jobs and studies among professionals (scientists, graduate and undergraduate students) and children. To this end, the authors collected intriguing science stories as the basis of scenarios, and drew four-cut comic strips, first on paper and subsequently as computer files.…

  9. Anatomy Comic Strips

    Science.gov (United States)

    Park, Jin Seo; Kim, Dae Hyun; Chung, Min Suk

    2011-01-01

    Comics are powerful visual messages that convey immediate visceral meaning in ways that conventional texts often cannot. This article's authors created comic strips to teach anatomy more interestingly and effectively. Four-frame comic strips were conceptualized from a set of anatomy-related humorous stories gathered from the authors' collective…

  10. ALICE silicon strip module

    CERN Multimedia

    Maximilien Brice

    2006-01-01

    This small silicon detector strip will be inserted into the inner tracking system (ITS) on the ALICE detector at CERN. This detector relies on state-of-the-art particle tracking techniques. These double-sided silicon strip modules have been designed to be as lightweight and delicate as possible as the ITS will eventually contain five square metres of these devices.

  11. Sociologia qualitativa e interazionismo simbolico: recenti sviluppi negli U.S.A.

    Directory of Open Access Journals (Sweden)

    Giuseppe Toscano

    2007-03-01

    Full Text Available Nel corso di due seminari realizzati nell’ambito del progetto Cofin “La ricerca qualitativa: teorie, metodi ed applicazioni”, tenuti rispettivamente a Roma e a Catania, il professor Fontana ha fornito un quadro generale sui recenti sviluppi dell’Interazionismo simbolico negli Stati Uniti.

  12. Formulation development of novel in situ nanoemulgel (NEG) of ketoprofen for the treatment of periodontitis.

    Science.gov (United States)

    Srivastava, M; Kohli, K; Ali, M

    2016-01-01

    The aim of the present study was to formulate and evaluate in situ gelling syringeable nanoemulgels (NEGs) of ketoprofen for periodontal delivery. Application of 3-factor 3-level design was employed using the Box-Behnken experimental design for the optimization of nanoemulsion using three independent variables such as percent concentration (v/v) of oil (X1), S mix (mixture of surfactant and cosurfactant) (X2) and water (X3); while the particle size (nm) (Y1), polydispersity index (Y2) and zeta potential (mV) (Y3) were used as dependent variables. The NEG was evaluated based on their drug content, pH measurement, mucoadhesion on the goat buccal mucosa, syringeability and inverted sol-gel transition temperature. The drug release data were analyzed for curve fitting based on the Korsmeyer-Peppas law, and the n-values of optimized A5 and A8 formulations were found 0.3721 and 0.3932, respectively, confirmed that both the formulations followed pseudo Fickian diffusion (n < 0.43). The formulation A8 with the optimal drug release was identified as the best NEG formulation. Results of rheological, mucoadhesion and syringeability studies showed the suitability of desired sol-gel property for periodontal drug delivery. The Herschel-Bulkley model was the best fit model to explain the flow behavior of optimized formulation. Using the HET-CAM method, significantly lower in vitro toxicity was indicated the suitability of developed NEG for intra-pocket delivery.

  13. Stripping with dry ice

    Science.gov (United States)

    Malavallon, Olivier

    1995-04-01

    Mechanical-type stripping using dry ice (solid CO2) consists in blasting particles of dry ice onto the painted surface. This surface can be used alone or in duplex according to type of substrate to be treated. According to operating conditions, three physical mechanisms may be involved when blasting dry ice particles onto a paint system: thermal shock, differential thermal contraction, and mechanical shock. The blast nozzle, nozzle travel speed, blast angle, stripping distance, and compressed air pressure and media flow rate influence the stripping quality and the uniformity and efficiency obtained.

  14. Inovação do modelo de negócio: um estudo de caso no IPT

    OpenAIRE

    Rubim, Fábio de Rezende

    2010-01-01

    O trabalho discute a inovação de Modelo de Negócio nas organizações. Um Modelo de Negócio é a maneira como uma empresa organiza seus recursos, competências e relacionamentos, de forma a criar valor para seus clientes. No ambiente atual de dinamismo e competitividade crescentes, passa a ser fundamental que as empresas desenvolvam Modelos de Negócio inovadores, para poderem se diferenciar de seus concorrentes, e criarem vantagens competitivas duradouras. Empresas como Dell, Amazon, Wal...

  15. Use of non evaporable getter pumps to ensure long term performances of high quantum efficiency photocathodes

    Energy Technology Data Exchange (ETDEWEB)

    Sertore, Daniele, E-mail: daniele.sertore@mi.infn.it; Michelato, Paolo; Monaco, Laura [Istituto Nazionale di Fisica Nucleare Sez. Milano – LASA, Via Fratelli Cervi 201, I-20090 Segrate (Italy); Manini, Paolo; Siviero, Fabrizio [SAES Getters S.p.A., Viale Italia 77, 20020 Lainate (Italy)

    2014-05-15

    High quantum efficiency photocathodes are routinely used as laser triggered emitters in the advanced high brightness electron sources based on radio frequency guns. The sensitivity of “semiconductor” type photocathodes to vacuum levels and gas composition requires special care during preparation and handling. This paper will discuss the results obtained using a novel pumping approach based on coupling a 20 l s{sup −1} sputter ion getter pump with a CapaciTorr® D100 non evaporable getter (NEG) pump. A pressure of 8⋅10{sup −8} Pa was achieved using only a sputter ion pump after a 6 day bake-out. With the addition of a NEG pump, a pressure of 2⋅10{sup −9} Pa was achieved after a 2 day bake-out. These pressure values were maintained without power due to the ability of the NEG to pump gases by chemical reaction. Long term monitoring of cathodes quantum efficiencies was also carried out at different photon wavelengths for more than two years, showing no degradation of the photoemissive film properties.

  16. Contrato preliminar: eficácia nos negócios jurídicos complexos

    OpenAIRE

    Alem, Fabio Pedro

    2010-01-01

    A proposta desta dissertação é analisar criticamente o contrato preliminar nos negócios jurídicos complexos, com destaque para os graus de obrigatoriedade ou os níveis de predeterminação do conteúdo do contrato definitivo (fraco, médio e forte) e as consequências práticas do contrato preliminar nos negócios complexos. O ponto de partida do trabalho é a análise histórica e evolutiva da aplicação do contrato preliminar, seguida por uma apresentação de suas características f...

  17. Plano de negócios Monsaluz, Sociedade Agrícola Lda.

    OpenAIRE

    Rente, José Eduardo Lopes

    2014-01-01

    Este trabalho de projeto tem como finalidade a elaboração de um plano de negócios, para reconversão de uma empresa agrícola no Alentejo, com um investimento na produção de ovinos de aptidão leiteira. O presente trabalho de projeto é apresentado metodologicamente através de um plano de negócio, que se pretende constitua um guia de apoio á tomada de decisão na implantação e controlo desse projeto. Com base na caracterização e análise da situação atual da empresa, na análise do...

  18. Employee Identification with Corporate Values within the Danish Windmill Company NEG Micon

    DEFF Research Database (Denmark)

    Andersen, Mona Agerholm

    2008-01-01

    This paper presents the findings of a holistic study of the communication processes during a corporate value implementation within the Danish windmill company NEG Micon. This implies firstly a study of the different processes of management's formulation, construction and communication of the valu...... statement and secondly, how the employees receive the values. The paper illuminates the potential problems that may occur during such a process and offer recommendations for future value implementation efforts in organisations....

  19. Flow and heat transfer in compact offset strip fin surfaces

    Institute of Scientific and Technical Information of China (English)

    Junqi DONG; Jiangping CHEN; Zhijiu CHEN

    2008-01-01

    Experimental studies of air-side heat transfer and pressure drop characteristics of offset strip fins and flat tube heat exchangers were performed. A series of tests were conducted for 9 heat exchangers with different fin space, fin height, fin strip length and flow length, at a constant tube-side water flow rate of 2.5 m3/h. The char-acteristics of the heat transfer and pressure drop of differ-ent fin space, fin height and fin length were analyzed and compared. The curves of the heat transfer coefficients vs. The pumping power per unit frontal area were then plot-ted. Moreover, the enhanced heat transfer mechanism of offset strip fins was analyzed using field synergy theory. The results showed that fin length and flow length have more obviously effect on the thermal hydraulic character-istics of offset strip fins.

  20. micro strip gas chamber

    CERN Multimedia

    1998-01-01

    About 16 000 Micro Strip Gas Chambers like this one will be used in the CMS tracking detector. They will measure the tracks of charged particles to a hundredth of a millimetre precision in the region near the collision point where the density of particles is very high. Each chamber is filled with a gas mixture of argon and dimethyl ether. Charged particles passing through ionise the gas, knocking out electrons which are collected on the aluminium strips visible under the microscope. Such detectors are being used in radiography. They give higher resolution imaging and reduce the required dose of radiation.

  1. [Post-stripping telangiectasis].

    Science.gov (United States)

    Hutinel, B; Maraval, M

    1985-01-01

    These telangiectasia appear between one and six months after the operation, especially in cases of capillary fragility. The most common localizations are the antero-internal and external sides of the thighs and knees. Unnecessary strippings, of continent saphenous veins, are the most frequent cause of these. Their prevention consists of the least possible traumatising stripping, using a fine stripper, a very rigorous post-operative support, and the wearing of light varicose stockings or tights for between one and three months. The treatment using microsclerosis, often delicate, should not be undertaken before six months.

  2. Centrifugal pumps

    CERN Document Server

    Anderson, HH

    1981-01-01

    Centrifugal Pumps describes the whole range of the centrifugal pump (mixed flow and axial flow pumps are dealt with more briefly), with emphasis on the development of the boiler feed pump. Organized into 46 chapters, this book discusses the general hydrodynamic principles, performance, dimensions, type number, flow, and efficiency of centrifugal pumps. This text also explains the pumps performance; entry conditions and cavitation; speed and dimensions for a given duty; and losses. Some chapters further describe centrifugal pump mechanical design, installation, monitoring, and maintenance. The

  3. Pumping life

    DEFF Research Database (Denmark)

    Sitsel, Oleg; Dach, Ingrid; Hoffmann, Robert Daniel

    2012-01-01

    of membrane proteins: P-type ATPase pumps. This article takes the reader on a tour from Aarhus to Copenhagen, from bacteria to plants and humans, and from ions over protein structures to diseases caused by malfunctioning pump proteins. The magazine Nature once titled work published from PUMPKIN ‘Pumping ions......’. Here we illustrate that the pumping of ions means nothing less than the pumping of life....

  4. ALICE Silicon Strip Detector

    CERN Multimedia

    Nooren, G

    2013-01-01

    The Silicon Strip Detector (SSD) constitutes the two outermost layers of the Inner Tracking System (ITS) of the ALICE Experiment. The SSD plays a crucial role in the tracking of the particles produced in the collisions connecting the tracks from the external detectors (Time Projection Chamber) to the ITS. The SSD also contributes to the particle identification through the measurement of their energy loss.

  5. Escopo de projeto para criação de um Plano de Negócios

    Directory of Open Access Journals (Sweden)

    Armando Terribili Filho

    2014-04-01

    Full Text Available No Brasil, 27% das empresas criadas encerrem suas atividades no primeiro ano de existência, e 58% delas até o final do quinto ano. Assim, os objetivos do artigo são: apresentar a composição de um Plano de Negócios por meio da EAP (Estrutura Analítica de Projetos utilizando o padrão do Guia PMBOK® (Project Management Body of Knowledge, e discutir se a criação de um Plano de Negócios aumentaria a probabilidade de sucesso de uma nova empresa. A metodologia utilizada foi composta de três etapas: revisão bibliográfica, definição dos entregáveis de um projeto para criação de um novo negócio e análise das principais razões para o encerramento de uma empresa em seus primeiros anos de existência. Os resultados apontaram que a existência de um Plano de Negócios não é sinônimo de sucesso, mas, certamente aumenta a probabilidade disto acontecer, pois a maioria das causas identificadas teria sido suprida pela elaboração de um Plano de Negócios.

  6. Magnetocaloric pump

    Science.gov (United States)

    Brown, G. V.

    1973-01-01

    Very cold liquids and gases such as helium, neon, and nitrogen can be pumped by using magnetocaloric effect. Adiabatic magnetization and demagnetization are used to alternately heat and cool slug of pumped fluid contained in closed chamber.

  7. Parabolic Strip Telescope

    CERN Document Server

    Chadzitaskos, Goce

    2013-01-01

    We present a proposal of a new type of telescopes using a rotating parabolic strip as the primary mirror. It is the most principal modification of the design of telescopes from the times of Galileo and Newton. In order to demonstrate the basic idea, the image of an artificial constellation observed by this kind of telescope was reconstructed using the techniques described in this article. As a working model of this new telescope, we have used an assembly of the primary mirror---a strip of acrylic glass parabolic mirror 40 cm long and 10 cm wid shaped as a parabolic cylinder of focal length 1 m---and an artificial constellation, a set of 5 apertures in a distance of 5 m illuminated from behind. In order to reconstruct the image, we made a series of snaps, each after a rotation of the constellation by 15 degrees. Using Matlab we reconstructed the image of the artificial constellation.

  8. Heat pumps

    CERN Document Server

    Macmichael, DBA

    1988-01-01

    A fully revised and extended account of the design, manufacture and use of heat pumps in both industrial and domestic applications. Topics covered include a detailed description of the various heat pump cycles, the components of a heat pump system - drive, compressor, heat exchangers etc., and the more practical considerations to be taken into account in their selection.

  9. Transcriptional Analysis of Acinetobacter sp. neg1 Capable of Degrading Ochratoxin A

    Science.gov (United States)

    Liuzzi, Vania C.; Fanelli, Francesca; Tristezza, Mariana; Haidukowski, Miriam; Picardi, Ernesto; Manzari, Caterina; Lionetti, Claudia; Grieco, Francesco; Logrieco, Antonio F.; Thon, Michael R.; Pesole, Graziano; Mulè, Giuseppina

    2017-01-01

    Ochratoxin A (OTA) is a nephrotoxic and potentially carcinogenic mycotoxin produced by several species of Aspergillus and Penicillium, contaminating grapes, wine and a variety of food products. We recently isolated from OTA contaminated soil vineyard a novel free-living strain of Acinetobacter sp. neg1, ITEM 17016, able to degrade OTA into the non-toxic catabolic product ochratoxin α. Biochemical studies suggested that the degradation reaction proceeds via peptide bond hydrolysis with phenylalanine (Phe) release. In order to identify genes responsible for OTA degradation we performed a differential gene expression analysis of ITEM 17016 grown in the presence or absence of the toxin. Among the differentially expressed genes, six peptidases up-regulated at 6 h were identified. The degrading activity of the carboxypeptidase PJ_1540 was confirmed in vitro in a heterologous system. The enrichment analysis for Gene Ontology terms confirmed that OTA degradation proceeds through peptidase activities and revealed the over-representation of pathways related to Phe catabolism. These results indicate that Phe may represent an energy source for this Acinetobacter sp. neg1 strain and that OTA degrading reaction triggers the modulation of further catabolic activities. PMID:28119679

  10. A Internet das Coisas e o Big Data inovando os negócios

    Directory of Open Access Journals (Sweden)

    Dalma de Oliveira Santos

    2016-10-01

    Full Text Available A Internet das Coisas e o Big Data permitem que grandes volumes de dados sejam analisados, verificados e transformados em informações organizadas para as empresas. Essas informações são utilizadas para que as empresas possam tomar as melhores decisões, apoiando o surgimento de novas perspectivas e, assim, possibilitando que novos impactos transformem a maneira de criar e expandir os negócios. O uso dessas ferramentas cresceu nos últimos anos e existem previsões de crescimento ainda maiores para os próximos anos, inovando o tratamento de dados no cotidiano das empresas fazendo com que os negócios sofram impactos em seus paradigmas. Empresas e usuários precisam se preocupar com as consequências dessa nova maneira de tratamento de dados. O objetivo desse artigo é tratar os aspectos que modificam a forma de trabalho, o uso em empresas e de usuários com o advento da conectividade entre objetos: máquinas com máquinas e pessoas com objetos e máquinas. Além de se propor a analisar as vantagens, as desvantagens e os riscos do uso dessas tecnologias.

  11. Heat pumps

    CERN Document Server

    Brodowicz, Kazimierz; Wyszynski, M L; Wyszynski

    2013-01-01

    Heat pumps and related technology are in widespread use in industrial processes and installations. This book presents a unified, comprehensive and systematic treatment of the design and operation of both compression and sorption heat pumps. Heat pump thermodynamics, the choice of working fluid and the characteristics of low temperature heat sources and their application to heat pumps are covered in detail.Economic aspects are discussed and the extensive use of the exergy concept in evaluating performance of heat pumps is a unique feature of the book. The thermodynamic and chemical properties o

  12. Derivazioni, ripetizione, manipolazione: note sulla recezione implicita di Vilfredo Pareto negli Stati Uniti

    Directory of Open Access Journals (Sweden)

    Angela Maria Zocchi

    2017-08-01

    Full Text Available Parlare di Pareto, oggi, significa occuparsi di un classico della sociologia che è stato oggetto di una ricezione/recezione discontinua, non solo in Europa ma anche, forse soprattutto, in America. Se negli anni Venti James Harvey Robinson scriveva che la teoria dei residui e delle derivazioni di Pareto si poteva annoverare tra le grandi scoperte scientifiche, è anche vero che la figura di Pareto ha suscitato riserve e perplessità, e che i suoi meriti «furono riconosciuti soltanto dieci anni dopo la sua morte, e per di più in America» (Coser [1977] 1983, p. 582, in particolare ad Harvard (Femia, Marshall 2012. Si pensi ad esempio a Parsons, che negli anni Trenta, ne La struttura dell’azione sociale, richiama ampiamente Pareto (Parsons [1937] 1968, o anche a Merton, il quale, sebbene non sia stato mai molto attratto dalle analisi paretiane (cfr. Coser 1975, p. 96; Coser [1977] 1983, p. 585, nell’intervista rilasciata ad Anna Di Lellio ha ricordato il grande interesse con il quale seguì i seminari di Henderson su Pareto (cfr. Di Lellio 1985, p. 17. E in effetti, negli anni Trenta gli Stati Uniti sono stati estremamente recettivi nei confronti dell’opera di Pareto. Successivamente, però, questo interesse si è fortemente ridimensionato, per poi riaccendersi negli anni Cinquanta e Sessanta, non solo in America ma anche in Europa, come testimoniato, fra l’altro, dall’attenzione riservata a Pareto da Raymond Aron ([1967] 1989. Una ricezione/recezione discontinua, quindi, che ha caratterizzato anche i decenni successivi e il nuovo millennio (cfr. Federici 1991, 1999, 2016, con studi che hanno cercato di rispondere anche a un inquietante interrogativo (cfr. Cirillo 1983; Femia e Marshall 2012: se Pareto fosse vissuto più a lungo, si sarebbe opposto al fascismo? Ciò premesso, partendo dalla distinzione tra ricezione e recezione, il paper intende strutturare una riflessione sulla recezione di Pareto negli Stati Uniti. Non mi soffermer

  13. H- Beam Stripping Loss at Background Partial Pressure of Ar

    Institute of Scientific and Technical Information of China (English)

    Hu Chundong; Wang Shaohu; Hu Liqun

    2005-01-01

    It has been observed that H- current could be improved by adding Ar to H2 plasma.But due to a slower pumping speed for Ar with the existing pumping scheme, the tank pressure will increase quickly during the length of a beam pulse. Since H- stripping loss depends on the tank pressure and gas species, part of the H- beam can be converted to H0 and then H0 can be converted into H+ with background H2 and Ar gas thickness. Therefore, the H- beam current,measured by a Faraday cup, situated at a distance L from GG (ground grid), will decrease because it will be converted into a H+ current. This gives a ratio of the Faraday cup net current to the H- beam current before stripping at background partial pressure of Ar.

  14. Spray Rolling Aluminum Strip

    Energy Technology Data Exchange (ETDEWEB)

    Lavernia, E.J.; Delplanque, J-P; McHugh, K.M.

    2006-05-10

    Spray forming is a competitive low-cost alternative to ingot metallurgy for manufacturing ferrous and non-ferrous alloy shapes. It produces materials with a reduced number of processing steps, while maintaining materials properties, with the possibility of near-net-shape manufacturing. However, there are several hurdles to large-scale commercial adoption of spray forming: 1) ensuring strip is consistently flat, 2) eliminating porosity, particularly at the deposit/substrate interface, and 3) improving material yield. Through this program, a new strip/sheet casting process, termed spray rolling, has been developed, which is an innovative manufacturing technique to produce aluminum net-shape products. Spray rolling combines the benefits of twin-roll casting and conventional spray forming, showing a promising potential to overcome the above hurdles associated with spray forming. Spray rolling requires less energy and generates less scrap than conventional processes and, consequently, enables the development of materials with lower environmental impacts in both processing and final products. Spray Rolling was developed as a collaborative project between the University of California-Davis, the Colorado School of Mines, the Idaho National Engineering and Environmental Laboratory, and an industry team. The following objectives of this project were achieved: (1) Demonstration of the feasibility of the spray rolling process at the bench-scale level and evaluation of the materials properties of spray rolled aluminum strip alloys; and (2) Demonstration of 2X scalability of the process and documentation of technical hurdles to further scale up and initiate technology transfer to industry for eventual commercialization of the process.

  15. Comércio eletrônico, modelos de negócios e a dinâmica organizacional : caso Cisco

    OpenAIRE

    Rufino, Mônica Soares

    2010-01-01

    Trata dos modelos de negócio que as empresas adotam para implantar o comércio eletrônico e obter vantagens competitivas. Aborda as características dos modelos de negócio, assim como, as estratégias e a dinâmica organizacional inerentes ao processo.

  16. Comércio eletrônico, modelos de negócios e a dinâmica organizacional : caso Cisco

    OpenAIRE

    Rufino, Mônica Soares

    2010-01-01

    Trata dos modelos de negócio que as empresas adotam para implantar o comércio eletrônico e obter vantagens competitivas. Aborda as características dos modelos de negócio, assim como, as estratégias e a dinâmica organizacional inerentes ao processo.

  17. Book review. Procedure cliniche e terapeutiche negli animali esotici. Marta Avanzi

    Directory of Open Access Journals (Sweden)

    Manuel Graziani

    2014-12-01

    Full Text Available Negli ultimi anni è in costante aumento il numero degli animali da compagnia, con la diretta conseguenza che negli ambulatori veterinari arrivano sempre più pet diversi dal cane e dal gatto. Per dare loro cure di qualità non è sufficiente conoscere soltanto la fisiologia e la patologia ma c'è bisogno di saper maneggiare correttamente questi animali non convenzionali, oltre che conoscere le procedure per arrivare a una diagnosi e quindi ad una terapia appropriata. Procedure cliniche e terapeutiche negli animali esotici di Marta Avanzi risponde al bisogno di conoscenza in un settore in cui la formazione accademica è ancora scarsa, a fronte di un aumento della richiesta di cure da parte dei proprietari. Come scrive l'autrice nella prefazione: "Non sempre il professionista ha la possibilità di seguire un periodo di tirocinio pratico presso colleghi più esperti e spesso è la mancanza di esperienza che scoraggia il neofita ad ampliare il range di specie a cui dedicarsi. Il libro nasce proprio dall'esigenza di colmare questa lacuna, rispondendo al bisogno crescente di formazione nel campo della cura e del trattamento degli animali esotici da compagnia". Il manuale della dott.ssa Avanzi illustra con chiarezza le procedure diagnostiche, anestesiologiche, terapeutiche indispensabili per la pratica clinica. Per questo è rivolto principalmente ai medici veterinari che si occupano degli animali esotici da compagnia quali furetti, conigli, roditori, uccelli e rettili, di cui vengono illustrate le tecniche fondamentali per maneggiarli e contenerli con competenza e sicurezza. Il volume, pubblicato nel grande formato 19,5x26,5 cm, contiene più di mille fotografie a colori, comprese quelle delle attrezzature specifiche per i vari casi. Un'iconografia ricchissima che ha la funzione di descrivere passo dopo passo le manovre e le procedure per trattare questi particolari pazienti. I capitoli sono 14 e descrivono circa 150 procedure, dalla dermatologia all

  18. Centrifugal pumps

    CERN Document Server

    Gülich, Johann Friedrich

    2014-01-01

    This book gives an unparalleled, up-to-date, in-depth treatment of all kinds of flow phenomena encountered in centrifugal pumps including the complex interactions of fluid flow with vibrations and wear of materials. The scope includes all aspects of hydraulic design, 3D-flow phenomena and partload operation, cavitation, numerical flow calculations, hydraulic forces, pressure pulsations, noise, pump vibrations (notably bearing housing vibration diagnostics and remedies), pipe vibrations, pump characteristics and pump operation, design of intake structures, the effects of highly viscous flows, pumping of gas-liquid mixtures, hydraulic transport of solids, fatigue damage to impellers or diffusers, material selection under the aspects of fatigue, corrosion, erosion-corrosion or hydro-abrasive wear, pump selection, and hydraulic quality criteria. As a novelty, the 3rd ed. brings a fully analytical design method for radial impellers, which eliminates the arbitrary choices inherent to former design procedures. The d...

  19. Strip shape control capability of hot wide strip rolling mills

    Institute of Scientific and Technical Information of China (English)

    Renzhong Wang; Quan Yang; Anrui He; Jian Shao; Haitao Bian

    2008-01-01

    The elasticity deformation of rolls was analyzed by means of two-dimensional f'mite element method (FEM) with vari-able thickness. Three typical mills were used as objects for analysis. A thorough study was done on the control capabilities of these mills on the strip shape. Then the strip shape control capabilities of the three mills was compared synthetically.

  20. Administrando o Negócio Através de Estratégias Ambientais

    Directory of Open Access Journals (Sweden)

    Silvia Maria Malaman

    2008-07-01

    Full Text Available A relação entre lucro e preservação do meio ambiente só pode ser definida quando se estabelece vínculo entre estratégias ambientais e continuidade do negócio. Para tanto, a empresa deve definir, conforme sua política ambiental, quais são os impactos ambientais relacionados à suas atividades e produtos e qual é a respectiva influência na gestão do negócio, através de metodologia sistemática para identificar as oportunidades de melhoria da produtividade e imagem da empresa. Só então, estratégias devem ser definidas para que a legislação ambiental vigente seja atendida e atividades voluntárias de preservação ambiental sejam implementadas. A referência empírica assumida para o desenvolvimento deste trabalho é a aplicação bem sucedida de estratégia ambiental na administração do negócio em uma indústria química, de forma a manter a organização adequada às exigências legais e incentivar a conscientização ecológica nos colaboradores responsáveis pelas atividades produtivas geradoras de poluentes. A metodologia utilizada foi a análise documental e entrevistas com executivos da organização. Concluiu-se que a organização cumpre sua Política Ambiental através de ações efetivas de proteção ao meio ambiente e ao negócio. Palavras-chave: estratégia ambiental, gerenciamento ambiental Abstract The relationship between profit and preservation of the environment can only be defined when the organization settles down entail between environmental strategies and continuity of the business. For so much, the company should define, according to its environmental politics, which are the environmental impacts related to its activities and products and which are the respective influence in the administration of the business, through systematic methodology to identify the opportunities of improvement of the productivity and image of the company. Only then, strategies should be defined so that the effective

  1. PosNeg opinion: Una herramienta para gestionar comentarios de la Web

    Directory of Open Access Journals (Sweden)

    Mario Amores

    2015-01-01

    Full Text Available One of the primary tasks of opinion mining is the classification of the polarity of the opinion, that consists in determining whether the opinion is positive or negative with respect to the entity to which it is referring. This work seeks design a general scheme consists in five stages that enable the polarity detection of opinions in an unsupervised manner. The five considered stages are: token identification, lexical disambiguation, get all meanings of each word, classify each token in positive or negative, and evaluate the opinion. PosNeg Opinion detects the polarity of the opinions in Spanish language. The proposed system showed good performance in classifying the polarity of 200 opinions from discussion forums Yahoo.es, yielding an accuracy of 0.965 and a precision of 0.970.

  2. Unionismo fiorentino negli anni Venti. L’Associazione Cristiana dei Giovani di Firenze

    Directory of Open Access Journals (Sweden)

    Letizia Pagliai

    2013-02-01

    Full Text Available Scarni sono i riferimenti storiografici sulla sezione fiorentina dell’Associazione Cristiana dei Giovani (ACDG, il corrispettivo italiano della Young Men’s Christian Association (YMCA, costituita dopo la Grande Guerra da quel Giovanni Battista Giorgini (1898-1971, noto piuttosto come talento imprenditoriale della ‘moda italiana’ negli anni del Miracolo economico. Sotto la presidenza di Giorgini (1924-1933, di formazione religiosa valdese, la sezione fiorentina dell’ACDG divenne punto di riferimento di tutta l’organizzazione italiana. Questo contributo, attraverso documenti esemplificativi, segue alcune fondamentali tappe e aspetti della vita dell’Associazione fino al 1931, quando il governo fascista ne intimò drasticamente lo scioglimento con ordinanza prefettizia.

  3. Francisco Ferreira Saturnino Braga: negócios e fortuna em Campos dos Goytacazes

    Directory of Open Access Journals (Sweden)

    Walter Luiz Carneiro de Mattos Pereira

    2012-12-01

    Full Text Available O artigo pretende investir no estudo da dinâmica da economia em Campos dos Goytacazes, Rio de Janeiro, nas duas décadas que antecedem a abolição da escravatura no Brasil, a partir dos negócios e da fortuna de Francisco Ferreira Saturnino Braga, proprietário de terras, escravos, usineiro, industrial, concessionário de ferrovias e banqueiro, figura-chave para se perceberem as transformações ocorridas em uma área de produção açucareira voltada para o mercado interno. As singularidades e particularidades obtidas pela observação em escala reduzida podem revelar a possibilidade de perceber uma articulação mais ampla com as estruturas de uma economia de mercado.

  4. The distribution of micro zooplankton in the lagoon environments; La distribuzione del microzooplancton negli ambienti lagunari

    Energy Technology Data Exchange (ETDEWEB)

    Grenni, P.; Creo, C. [ENEA, Centro Ricerche Casaccia, Rome (Italy). Dipt. Ambiente

    1998-07-01

    The aim of this work is to verify the possible use of micro zooplankton as a biological indicator in aquatic environments. In particular, studies carried out in lagoon environments are reported, relatively to the Venice lagoon and the Pontine coastal lakes (Italy). New methodologies to assess the micro plankton component are developed and tested, particularly the concentration and count steps. The use of the same methodologies to assess nano plankton component, as biological indicator. are reported. [Italian] Nel presente lavoro viene analizzata la possibilita' di utilizzare il microzooplancton quale indicatore biologico negli ambienti acquatici (mmarini, acquadulcicoli, salmastri). In particolare, vengono riportati gli studi effettuati dall'ENEA (National Agency for New Technology, Energy and the Environment) su tale componente in ambienti lagunari, con riferimento alla laguna di Venezia e alle lagune pontine.

  5. Evaluation for NegFry Potato Late Blight Forecasting Model%NegFry马铃薯晚疫病预测预报模型的评价

    Institute of Scientific and Technical Information of China (English)

    闵凡祥; 郭梅; 高云飞; 吕典秋; 王晓丹; 胡林双; 杨帅

    2013-01-01

      本研究主要应用丹麦NegFry马铃薯晚疫病预测预报模型,以不喷药和每7 d喷药作对照,采用感病品种‘Favorita’和中抗品种‘克新18’进行田间试验,对马铃薯晚疫病进行预测和防治。感病品种不喷药处理(CK1)、感病品种每7 d施药处理(FW)、感病品种测报处理(FN)、中抗品种不喷药处理(CK2)、中抗品种每7 d施药处理(KW)和中抗品种测报处理(KN)的AUDPC值分别为12.73、0.12、0.17、0.12、0.074和0.034,通过邓肯多重极差法(LSR法)进行比较, CK1与FW, FN, CK2, KW, KN 5个处理差异显著,其余各处理之间差异不显著。说明采用测报处理,每7 d施药处理和采用抗病品种能够达到同等防治效果。对于感病品种,测报处理与每7 d施药处理相比减少杀菌剂使用次数2次,每667 m2降低成本70元,与每7 d施药处理相比每667 m2增收27元。对于抗病品种,测报处理与每7 d施药处理相比减少杀菌剂使用次数5次,每667 m2降低成本160元,与每7 d施药处理相比每667 m2增收213元。所以,通过丹麦NegFry预测预报模型,可以准确得出施药时间,既降低生产成本,又有效防控马铃薯晚疫病,同时又提高马铃薯产量和质量。%The potato late blight forecasting model is an efficient tool to deal with this problem. The purpose of this study was to apply NegFry forecasting model for the control of late blight in Heilongjiang Province, with no application and application of fungicides weekly as controls and using susceptible variety 'Favorita' and moderately resistant variety 'Kexin 18' as tested plant materials. Area under Disease Progress Curve (AUDPC) of CK1 (susceptible variety with no fungicide application), FW (susceptible variety with fungicide application weekly), FN (susceptible variety with fungicide application based on Negfry model), CK2 (resistant variety with no fungicide

  6. Ferroelectric Pump

    Science.gov (United States)

    Jalink, Antony, Jr. (Inventor); Hellbaum, Richard F. (Inventor); Rohrbach, Wayne W. (Inventor)

    2000-01-01

    A ferroelectric pump has one or more variable volume pumping chambers internal to a housing. Each chamber has at least one wall comprising a dome shaped internally prestressed ferroelectric actuator having a curvature and a dome height that varies with an electric voltage applied between an inside and outside surface of the actuator. A pumped medium flows into and out of each pumping chamber in response to displacement of the ferroelectric actuator. The ferroelectric actuator is mounted within each wall and isolates each ferroelectric actuator from the pumped medium, supplies a path for voltage to be applied to each ferroelectric actuator, and provides for positive containment of each ferroelectric actuator while allowing displacement of the entirety of each ferroelectric actuator in response to the applied voltage.

  7. Analysis/design of strip reinforced random composites (strip hybrids)

    Science.gov (United States)

    Chamis, C. C.; Sinclair, J. H.

    1978-01-01

    Advanced analysis methods and composite mechanics were applied to a strip-reinforced random composite square panel with fixed ends to illustrate the use of these methods for the a priori assessment of the composite panel when subjected to complex loading conditions. The panel was assumed to be of E-glass random composite. The strips were assumed to be of three advanced unidirectional composites to cover a range of low, intermediate, and high modulus stiffness. The panels were assumed to be subjected to complex loadings to assess their adequacy as load-carrying members in auto body, aircraft engine nacelle and windmill blade applications. The results show that strip hybrid panels can be several times more structurally efficient than the random composite base materials. Some of the results are presented in graphical form and procedures are described for use of these graphs as guides for preliminary design of strip hybrids.

  8. Analysis/design of strip reinforced random composites /strip hybrids/

    Science.gov (United States)

    Chamis, C. C.; Sinclair, J. H.

    1978-01-01

    Results are described which were obtained by applying advanced analysis methods and composite mechanics to a strip-reinforced random composite square panel with fixed ends. This was done in order to illustrate the use of these methods for the apriori assessment of the composite panel when subjected to complex loading conditions. The panel was assumed to be of E-Glass/Random Composite. The strips were assumed to be of three advanced unidirectional composites to cover a range of low, intermediate, and high modulus stiffness. The panels were assumed to be subjected to complex loadings to assess their adequacy as load-carrying members in auto body, aircraft engine nacelle, and windmill blade applications. The results show that strip hybrid panels can be several times more structurally efficient than the random composite base materials. Some of the results are presented in graphical form and procedures are described for use of these graphs as guides for preliminary design of strip hybrids.

  9. Aptasensors Based on Stripping Voltammetry

    Directory of Open Access Journals (Sweden)

    Wenjing Qi

    2016-07-01

    Full Text Available Aptasensors based on stripping voltammetry exhibit several advantages, such as high sensitivity and multi-target detection from stripping voltammetric technology, and high selectivity from the specific binding of apamers with targets. This review comprehensively discusses the recent accomplishments in signal amplification strategies based on nanomaterials, such as metal nanoparticles, semiconductor nanoparticles, and nanocomposite materials, which are detected by stripping voltammetry after suitable dissolution. Focus will be put in discussing multiple amplification strategies that are widely applied in aptasensors for small biomolecules, proteins, disease markers, and cancer cells.

  10. Penis Pump

    Science.gov (United States)

    ... claim that they can be used to increase penis size, but there's no evidence that they work for ... circumstances, using a penis pump might help your penis maintain its natural size and shape after prostate surgery or if you ...

  11. Microtube strip heat exchanger

    Science.gov (United States)

    Doty, F. D.

    1991-04-01

    During the last quarter, Doty Scientific, Inc. (DSI) continued to make progress on the microtube strip (MTS) heat exchangers. The team has begun a heat exchanger stress analysis; however, they have been concentrating the bulk of their analytical energies on a computational fluid dynmaics (CFD) model to determine the location and magnitude of shell-side flow maldistribution which decreases heat exchanger effectiveness. DSI received 120 fineblanked tubestrips from Southern Fineblanking (SFB) for manufacturing process development. Both SFB and NIST provided inspection reports of the tubestrips. DSI completed the tooling required to encapsulate a tube array and press tubestrips on the array. Pressing the tubestrips on tube arrays showed design deficiencies both in the tubestrip design and the tooling design. DSI has a number of revisions in process to correct these deficiencies. The research effort has identified a more economical fusible alloy for encapsulating the tube array, and determined the parameters required to successfully encapsulate the tube array with the new alloy. A more compact MTS heat exchanger bank was designed.

  12. Magnetic stripping studies for SPL

    CERN Document Server

    Posocco, P; CERN. Geneva. BE Department

    2010-01-01

    Magnetic stripping of H- can seriously enhance the beam losses along the SPL machine. These losses depend on the beam energy, on the beam transverse distribution and on the intensity of the magnetic field. For radioprotection issues the losses must be limited to 1 W/m. In this paper we will concentrate on the stripping phenomena inside the quadrupole magnets with the aim of defining the quadrupole range for the design phase of SPL.

  13. Improved lower bound for online strip packing

    NARCIS (Netherlands)

    Harren, Rolf; Kern, Walter

    2012-01-01

    In the two-dimensional strip packing problem a number of rectangles have to be packed without rotation or overlap into a strip such that the height of the strip used is minimal. The width of the rectangles is bounded by 1 and the strip has width 1 and infinite height. We study the online version of

  14. The Dark Side of the Moebius Strip.

    Science.gov (United States)

    Schwarz, Gideon E.

    1990-01-01

    Discussed are various models proposed for the Moebius strip. Included are a discussion of a smooth flat model and two smooth flat algebraic models, some results concerning the shortest Moebius strip, the Moebius strip of least elastic energy, and some observations on real-world Moebius strips. (KR)

  15. Negócios jurídicos processuais: análise dos provimentos judiciais como atos negociais.

    OpenAIRE

    Nogueira, Pedro Henrique Pedrosa

    2011-01-01

    A tese investiga o problema da existência dos negócios jurídicos processuais no direito brasileiro. Busca-se examinar o tema à luz da noção de fato jurídico, construída no plano da Teoria Geral do Direito, para então, após examinar algumas classificações dos fatos processuais, indagar da sua aplicabilidade ao processo civil brasileiro. Ao fim, conclui-se pela existência de negócios processuais, realizados pelas partes e pelo juiz, quando emite certos provimentos para cuja prática a ordem jurí...

  16. Modelo de negócios: constructo real ou metáfora de estratégia?

    Directory of Open Access Journals (Sweden)

    Luiz Antonio Joia

    Full Text Available Este artigo analisa a discussão sobre os termos "modelo de negócios" e "estratégia", e seu principal objetivo é verificar se esses conceitos são distintos ou não. A maioria dos estudos até agora realizados defendem a tese de que sejam diferentes. O objetivo deste artigo é testar a veracidade dessa hipótese. Para isso, são comparadas abordagens consolidadas de estratégia, como a da escola de posicionamento e a visão baseada em recursos (resource-based view-RBV, com as definições de vários autores para o termo "modelo de negócios". Usando-se análise interpretativa de viés hermenêutico, conclui-se que os constructos não são totalmente diferentes, i.e., que existe sobreposição e nível de similaridade entre Estratégia e Modelo de Negócio. Da mesma forma, verifica-se que modelo de negócios é um instrumento dinâmico e sistêmico para várias abordagens de estratégia. Isso possibilita entrelaçá-las numa única definição, aumentando o potencial dessas abordagens para explicar e orientar o processo estratégico real das organizações.

  17. Francisco Ferreira Saturnino Braga: negócios e fortuna em Campos dos Goytacazes

    Directory of Open Access Journals (Sweden)

    Walter Luiz Carneiro de Mattos Pereira

    2012-12-01

    Full Text Available O artigo pretende investir no estudo da dinâmica da economia em Campos dos Goytacazes, Rio de Janeiro, nas duas décadas que antecedem a abolição da escravatura no Brasil, a partir dos negócios e da fortuna de Francisco Ferreira Saturnino Braga, proprietário de terras, escravos, usineiro, industrial, concessionário de ferrovias e banqueiro, figura-chave para se perceberem as transformações ocorridas em uma área de produção açucareira voltada para o mercado interno. As singularidades e particularidades obtidas pela observação em escala reduzida podem revelar a possibilidade de perceber uma articulação mais ampla com as estruturas de uma economia de mercado.The article intends to invest in the study of the dynamics of the economy in Campos dos Goytacazes, Rio de Janeiro, in the two decades preceding the abolition of slavery in Brazil, from the business and fortune of Francisco Ferreira Saturnino Braga, owner of land, slaves, mill owner, industrial, railroad dealer and banker, a key figure to understand the changes occurred in an area of the sugar production directs to the domestic market. The singularities and particularities obtained by observation in small scale may reveal the possibility of perceiving a broader articulation with the structures of a market economy.

  18. Food bike Rosa Mel: viabilidade do empreendimento por meio de Plano de Negócio

    Directory of Open Access Journals (Sweden)

    Danielle de Oliveira Barutti

    2016-02-01

    Full Text Available Este artigo objetiva propor a criação de um comércio itinerante de doces caseiros comercializando pão de mel, nos sabores brigadeiro, doce de leite e coco, trufas tradicionais, alfajor, café e água na modalidade Food Bike, na cidade de São Paulo. A modalidade Food Bike é o tipo de comércio itinerante em que se vendem comidas e bebidas, tendo como suporte uma bicicleta e não havendo necessidade de muito espaço para sua instalação. Utiliza-se como metodologia de análise, plano de negócio e pesquisa qualitativa exploratória para verificar o perfil do comércio itinerante e analisar o consumidor desse serviço. Foi concluído que este tipo de empreendimento é inovador, atraente, de baixo custo inicial, rentável e com taxa de retorno em torno de onze meses.

  19. 非蒸散型吸气剂泵在真空计量中的应用研究%Applications of Non-Evaporable Getter Pump in Vacuum Metrology

    Institute of Scientific and Technical Information of China (English)

    李得天; 成永军

    2011-01-01

    The non-evaporable getter (NEG) pump was, for the first time, applied to vacuum metrology, including the ultrahigh vacuum(UHV) standards,the extreme high vacuum XHV standard,and the static expansion vacuum standard.The preliminary results show that the NEG vacuum pump is capable of pumping the extremely high vacuum system down to 10- 10 Pa,and reducing the calibration lower limit of the static expansion vacuum system down to 10-7 Pa,respectively,at room temperature. The discussions focused on the operating principle of the NEG pump in vacuum metrology, and the feasibility of using the inert gases and the NEG pump to reduce the lower limit of the gas micro-flow rate,measured in the constant conductance method, below 10- 13 Pa· cm3/s.%本文简要阐述了非蒸散型吸气剂(NEG)泵的吸气机理,着重介绍了NEG泵在超高/极高真空标准、静态膨胀法真空标准等真空计量标准中的最新应用结果.结果表明:利用NEG泵在室温下获得了10-10mPa的XHV;利用NEG泵将超高/极高真空标准校准下限延伸到了10-10Pa量级;利用NEG泵将静态膨胀法真空标准的校准下限延伸到了10-7Pa量级.最后还对用NEG泵延伸固定流导法微流量标准测量下限的可行性进行了分析.

  20. LEP vacuum chamber, prototype

    CERN Multimedia

    CERN PhotoLab

    1983-01-01

    Final prototype for the LEP vacuum chamber, see 8305170 for more details. Here we see the strips of the NEG pump, providing "distributed pumping". The strips are made from a Zr-Ti-Fe alloy. By passing an electrical current, they were heated to 700 deg C.

  1. Pumps; Pumpen

    Energy Technology Data Exchange (ETDEWEB)

    Bauer, H. [Gesellschaft fuer Praktische Energiekunde e.V., Muenchen (Germany). Forschungsstelle fuer Energiewirtschaft; Hellriegel, E. [Gesellschaft fuer Praktische Energiekunde e.V., Muenchen (Germany). Forschungsstelle fuer Energiewirtschaft; Pfitzner, G. [Gesellschaft fuer Praktische Energiekunde e.V., Muenchen (Germany). Forschungsstelle fuer Energiewirtschaft

    1994-11-01

    The technical features of commercial pump types are described with regard to their technical, energy-related and economic parameters, and characteristic data are presented in the form of data sheets. This is to provide a basis for a comparative assessment of different technologies and technical variants. The chapter `System specifications` describes the various fields of application of pumps and the resulting specific requirements. The design and function of the different pump types are described in `Technical description`. `System and plant description dscribes the design and adaptation of pumps, i.e. the adaptation of the plant data to the system requirements. `Data compilation` provides a survey of the types and systematics of the compiled data as well as a decision aid for selecting the pumps best suited to the various applications. The `Data sheet` section describes the structure and handling of the data sheets as well as the data contained therein. The data sheets are contained in the apapendix of this report. The section `General analysis` compares typical technical, energy-related and economic characteristics of the different pump types. This is to enable a rough comparison of pump types and to facilitate decisions. The chapter `Example` illustrates the use of the data sheets by means of a selected example. (orig./GL) [Deutsch] Die vorliegende Arbeit hat zum Ziel, Technik seriengefertigter und marktgaengiger Pumpen in typisierter Form hinsichtlich ihrer technischen, energetischen und wirtschaftlichen Parameter zu beschreiben und ihre charakteristischen Kennwerte in Datenblaettern abzubilden. Damit wird ein grundlegendes Instrument fuer die vergleichende Beurteilung unterschiedlicher Techniken bzw. Technikvarianten hinsichtlich energetischer und wirtschaftlicher Kriterien geschaffen. Im Abschnitt `Systemanforderungen` erfolgt die Beschreibung der einzelnen Anwendungsbereiche fuer Pumpen mit den speziellen daraus resultierenden Anforderungen. Der Aufbau und

  2. Large tuning of birefringence in two strip silicon waveguides via optomechanical motion.

    Science.gov (United States)

    Ma, Jing; Povinelli, Michelle L

    2009-09-28

    We present an optomechanical method to tune phase and group birefringence in parallel silicon strip waveguides. We first calculate the deformation of suspended, parallel strip waveguides due to optical forces. We optimize the frequency and polarization of the pump light to obtain a 9 nm deformation for an optical power of 20 mW. Widely tunable phase and group birefringence can be achieved by varying the pump power, with maximum values of 0.026 and 0.13, respectively. The giant phase birefringence allows linear to circular polarization conversion within 30 microm for a pump power of 67 mW. The group birefringence gives a tunable differential group delay of 6fs between orthogonal polarizations. We also evaluate the tuning performance of waveguides with different cross sections.

  3. Restitution of enamel after interdental stripping.

    Science.gov (United States)

    Lundgren, T; Milleding, P; Mohlin, B; Nannmark, U

    1993-01-01

    This paper studies the effect of interdental stripping on the enamel surface and evaluates methods to restitute the treated surface. Extracted teeth mounted in a semielastic material were subjected to stripping by different kinds of steel strips. The treated enamel surfaces were then polished in several different ways. The effects were studied by SEM and profilometry. It was concluded that the coarsest strips produced irregularities of such a magnitude that polishing had very limited effect. Polishing starting with coarse polishing strips followed by gradually finer gave the best result. An increase in number of strokes and use of all grades of polishing strips slightly improved the result.

  4. Types of Breast Pumps

    Science.gov (United States)

    ... Devices Consumer Products Breast Pumps Types of Breast Pumps Share Tweet Linkedin Pin it More sharing options ... used for feeding a baby. Types of Breast Pumps There are three basic types of breast pumps: ...

  5. Neg·V优势到V·Neg优势——朝鲜语两种否定标记竞争导致的语法现象分析

    Institute of Scientific and Technical Information of China (English)

    白莲花

    2012-01-01

    Although negative constructions Neg V and V Neg coexist in the Korean language, the negative constructions have, from a diachronic perspective, undergone an evolvement from the dominance of the Neg V construction to the dominance of V Neg construction, resulting from the competition between the markers of two negative constructions. The shift of dominant negative constructions in the Korean language is triggered by an internal motive, which explains the synchronic linguistic feature.%朝鲜语否定结构中Neg·V和V·Neg并存。历时上经历的从Neg·V优势到V·Neg优势的演化,是两种否定标记相互竞争的结果。朝鲜语否定结构演变过程中蕴含的内在动因,可以解释共时的语言现象。

  6. Estratégia empresarial e modos de busca de novos negócios - uma análise das estratégias de busca de novos negócios em empresas brasileiras

    OpenAIRE

    Vasconcelos,Flávio Carvalho de

    2003-01-01

    O objetivo deste trabalho é a investigação de como as empresas brasileiras, no contexto nacional, empreendem a busca de novas oportunidades de negócios, identificando quais os fatores que mais claramente influenciam este comportamento. Este trabalho se estruturou a partir da operacionalização do modelo de modelo de busca estratégica e interpretação ambiental proposto por Richard Daft e Karl Weick em 1984. Foram para tanto realizadas análises estatísticas e teóricas a partir de uma pesquisa em...

  7. Hardy spaces for the strip

    Science.gov (United States)

    Bakan, Andrew; Kaijser, Sten

    2007-09-01

    In this paper we shall study Hardy spaces of analytic functions in a strip . Our main result is on one hand an intrinsic characterization of the spaces and on the second that polynomials are dense. We also present an orthogonal (in ) basis of polynomials.

  8. Intraply Hybrid Composites Would Contain Control Strips

    Science.gov (United States)

    Chamis, Christos C.; Shiao, Chi-Yu

    1996-01-01

    "Smart" structural components with sensors and/or actuators distributed throughout their volumes made of intraply hybrid composite materials, according to proposal. Strips of hybrid control material interspersed with strips of ordinary (passive) composite material in some layers, providing distributed control capability. For example, near and far edges of plate bent upward by commanding bottom control strips to expand and simultaneously commanding upper control strips to contract.

  9. Implicazioni della regolazione dei mercati dei derivati sulle materie prime negli USA e nell’Unione Europea

    Directory of Open Access Journals (Sweden)

    Jayati Ghosh

    2011-12-01

    Full Text Available Implicazioni della regolazione dei mercati dei derivati sulle materie prime negli USA e nell’Unione EuropeaAbstract: The argument for effective financial regulation to curb financial activity and associated volatility in primary commodity markets is now more compelling than ever, in the context of the renewed increase in food prices. However, as in much other financial regulation, the devil is in the detail. This paper considers recent patterns in global food markets and discusses some of the implications of recent moves to regulate financial activity in commodity futures markets in the US and the EU. Specific regulatory issues are considered and alternative strategies are considered.

  10. Turismo de Negócios. Convention & Visitors Bureau na Região Centro de Portugal

    OpenAIRE

    Marques, Jorge Humberto Soares

    2014-01-01

    Tese de doutoramento em Turismo, Lazer e Cultura, apresentada ao Departamento de Geografia da Faculdade de Letras da Universidade de Coimbra Para além do alojamento, dos espaços para reuniões, das acessibilidades e das organizações locais de apoio (como é o caso dos Convention & Visitors Bureaux) representarem uma grande importância no momento de escolha do local para realizar ou assistir a uma conferência ou outro evento de negócios, também a atratividade do destino, relacionada com as at...

  11. Sucesso, mídia de negócios e a cultura do management no Brasil

    OpenAIRE

    Cristiana Trindade Ituassu; Maria José Tonelli

    2014-01-01

    A lógica das modernas práticas de gestão ultrapassou a esfera econômica e disseminou-se como modelo de conduta para outras esferas da vida social, em um processo denominado management ou cultura do management, intensamente difundido após a Segunda Guerra Mundial. Ao se expandir para países em desenvolvimento, argumentamos que esse processo trouxe, entre outros valores, modelos de sucesso que se propagaram a partir da mídia de negócios. A mídia, entendida como comunicação de massa, possibilita...

  12. Using Comic Strips in Language Classes

    Science.gov (United States)

    Csabay, Noémi

    2006-01-01

    The author believes that using comic strips in language-learning classes has three main benefits. First, comic strips motivate younger learners. Second, they provide a context and logically connected sentences to help language learning. Third, their visual information is helpful for comprehension. The author argues that comic strips can be used in…

  13. Human Non-Hematopoietic CD271pos/CD140alow/neg Bone Marrow Stroma Cells Fulfill Stringent Stem Cell Criteria in Serial Transplantations

    Science.gov (United States)

    Ghazanfari, Roshanak; Li, Hongzhe; Zacharaki, Dimitra; Lim, Hooi Ching

    2016-01-01

    Human bone marrow contains a population of non-hematopoietic stromal stem/progenitor cells (BMSCs), which play a central role for bone marrow stroma and the hematopoietic microenvironment. However, the precise characteristics and potential stem cell properties of defined BMSC populations have not yet been thoroughly investigated. Using standard adherent colony-forming unit fibroblast (CFU-F) assays, we have previously shown that BMSCs were highly enriched in the nonhematopoietic CD271pos/CD140alow/neg fraction of normal adult human bone marrow. In this study, we demonstrate that prospectively isolated CD271pos/CD140alow/neg BMSCs expressed high levels of hematopoiesis supporting genes and signature mesenchymal and multipotency genes on a single cell basis. Furthermore, CD271pos/CD140alow/neg BMSCs gave rise to non-adherent sphere colonies (mesenspheres) with typical surface marker profile and trilineage in vitro differentiation potential. Importantly, serial transplantations of CD271pos/CD140alow/neg BMSC-derived mesenspheres (single cell and bulk) into immunodeficient NOD scid gamma (NSG) mice showed increased mesensphere numbers and full differentiation potential after both primary and secondary transplantations. In contrast, BMSC self-renewal potential decreased under standard adherent culture conditions. These data therefore indicate that CD271pos/CD140alow/neg BMSCs represent a population of primary stem cells with MSC phenotype and sphere-forming capacity that fulfill stringent functional stem cell criteria in vivo in a serial transplantation setting. PMID:27527928

  14. Fast variation method for elastic strip calculation.

    Science.gov (United States)

    Biryukov, Sergey V

    2002-05-01

    A new, fast, variation method (FVM) for determining an elastic strip response to stresses arbitrarily distributed on the flat side of the strip is proposed. The remaining surface of the strip may have an arbitrary form, and it is free of stresses. The FVM, as well as the well-known finite element method (FEM), starts with the variational principle. However, it does not use the meshing of the strip. A comparison of FVM results with the exact analytical solution in the special case of shear stresses and a rectangular strip demonstrates an excellent agreement.

  15. Negócios portugueses no Rio de Janeiro: um estudo sobre o Banco Português do Brasil (1918 a 1938

    Directory of Open Access Journals (Sweden)

    Teresa Cristina de Novaes Marques

    2011-12-01

    Full Text Available Este estudo explora a rede de negócios formada a partir do Banco Português do Brasil, constituído no Rio de Janeiro por integrantes da comunidade de imigrantes portugueses residentes na cidade. As atividades do banco são observadas por 20 anos, período no qual a economia da cidade sofreu expressivas mudanças, pois os negócios de importação, articulados em torno do porto, deram lugar a investimentos voltados para o mercado interno. O estudo explora, também, as conexões entre grupos empresariais do Rio de Janeiro e de Lisboa, buscando mostrar a importância do capital levantado em empreendimentos no Brasil para a sustentação de negócios em Portugal.

  16. A importância do conhecimento organizacional para o processo de inovação no modelo de negócio

    Directory of Open Access Journals (Sweden)

    Heron Jader Trierveiler

    2015-01-01

    Full Text Available O presente trabalho explora a relação entre conhecimento organizacional e inovação no modelo de negócio. Mais precisamente, sugere que as organizações que decidem inovar em seus modelos de negócio podem se beneficiar se considerarem o conhecimento que armazenam em seus repositórios como um insumo importante para o processo de inovação. Um mapeamento bibliométrico permitiu que os autores identificassem os artigos mais relevantes que tratam dos dois temas centrais da pesquisa. Como resultado da análise desses trabalhos, são listados e detalhados seis fatores que potencializam as chances de sucesso das iniciativas de inovação no modelo de negócio. Não por coincidência, cinco deles têm relação direta com o conhecimento organizacional. 

  17. Identifying and addressing unmet clinical needs in Ph-neg classical myeloproliferative neoplasms: a consensus-based SIE, SIES, GITMO position paper.

    Science.gov (United States)

    Barosi, Giovanni; Vannucchi, Alessandro M; De Stefano, Valerio; Pane, Fabrizio; Passamonti, Francesco; Rambaldi, Alessandro; Saglio, Giuseppe; Barbui, Tiziano; Tura, Sante

    2014-02-01

    This article presents the results of group discussion among experts from SIE, SIES and GITMO societies aimed at highlighting unmet challenges in the management of Ph-neg myeloproliferative neoplasms (MPNs). The issues analyzed were: diagnosis of prefibrotic myelofibrosis; diagnosis of Ph-neg MPNs in the setting of splanchnic vein thrombosis (SVT); management of low-risk PV and low-risk ET patients with JAK2V617F mutation; molecular biomarkers in the prognostic evaluation of myelofibrosis (MF); ruxolitinib therapy in low-risk MF; therapy in patients with SVT-associated Ph-neg MPN; indications of splenectomy in MF. For each of these issues, proposals for advancement in clinical research were addressed.

  18. Fatores relevantes de competitividade no negócio de consultoria de tecnologia da informação

    Directory of Open Access Journals (Sweden)

    Antonio Carlos Calicchio

    Full Text Available Resumo Este artigo identifica como as empresas de consultoria de tecnologia da informação (TI utilizam seus recursos e capacidades na busca pela vantagem competitiva, sob a abordagem da Visão Baseada em Recursos (VBR. A pesquisa foi do tipo exploratório e de natureza descritiva, tendo-se adotado o método qualitativo, com entrevistas em profundidade orientadas por um roteiro padrão com perguntas abertas. Foram entrevistados sete executivos da alta gestão de empresas de consultoria de TI classificadas entre as Top 10 deste segmento. Para a análise e interpretação dos dados, foi aplicada a Análise de Conteúdo, com o apoio de uma planilha para gerar as categorias da análise. Como resultado, foi identificado que as empresas que participaram da pesquisa utilizam-se do conhecimento dos seus recursos humanos e do relacionamento com os clientes, como componentes cruciais de suas estratégias de negócios. Esses recursos e capacidades são estrategicamente utilizados, aproveitando o vínculo estabelecido com o cliente na busca de novas oportunidades de negócios, de maneira a criar uma barreira às ameaças de novos entrantes.

  19. Antenna structure with distributed strip

    Science.gov (United States)

    Rodenbeck, Christopher T.

    2008-03-18

    An antenna comprises electrical conductors arranged to form a radiating element including a folded line configuration and a distributed strip configuration, where the radiating element is in proximity to a ground conductor. The folded line and the distributed strip can be electrically interconnected and substantially coplanar. The ground conductor can be spaced from, and coplanar to, the radiating element, or can alternatively lie in a plane set at an angle to the radiating element. Embodiments of the antenna include conductor patterns formed on a printed wiring board, having a ground plane, spacedly adjacent to and coplanar with the radiating element. Other embodiments of the antenna comprise a ground plane and radiating element on opposed sides of a printed wiring board. Other embodiments of the antenna comprise conductors that can be arranged as free standing "foils". Other embodiments include antennas that are encapsulated into a package containing the antenna.

  20. Pump characteristics and applications

    CERN Document Server

    Volk, Michael

    2013-01-01

    Providing a wealth of information on pumps and pump systems, Pump Characteristics and Applications, Third Edition details how pump equipment is selected, sized, operated, maintained, and repaired. The book identifies the key components of pumps and pump accessories, introduces the basics of pump and system hydraulics as well as more advanced hydraulic topics, and details various pump types, as well as special materials on seals, motors, variable frequency drives, and other pump-related subjects. It uses example problems throughout the text, reinforcing the practical application of the formulae

  1. A gestão dos clubes de futebol como clube empresa : estratégias de negócio

    OpenAIRE

    2000-01-01

    O esporte e, principalmente, o futebol, como negócio, tem evoluído muito nos últimos tempos. A indústria do esporte movimenta, anualmente, US$ 250 bilhões no mundo. No Brasil, o negócio do esporte está em fase de grande crescimento: somente o futebol movimenta US$ 2 bilhões anuais, representando 0,01% do PIB. Portanto, este campo de atividade vem estabelecendo fortes ligações com a atividade empresarial. A consulta à literatura, porém, mostra que, até agora, pouco está sendo realizado em dire...

  2. Integração da área de negócio de retalho do grupo Riopele no Data Warehouse corporativo

    OpenAIRE

    Matos, Pedro Miguel Carvalho

    2015-01-01

    Dissertação de mestrado integrado em Engenharia e Gestão de Sistemas de Informação O Grupo Riopele pretende dar continuidade ao crescimento organizacional verificado nos últimos anos, para isso precisa de compreender o negócio de retalho existente no seio do Grupo. A área retalhista do Grupo Riopele produz e possui informações e dados relevantes para o negócio, mas que não estão a ser integradas no Data Warehouse (DW) corporativo. Com recurso a tecnologias de Business Intellige...

  3. Gerenciamento de processos de negócio em biblioteca pública

    Directory of Open Access Journals (Sweden)

    Thatiane Aparecida de Lima Giviani

    2015-09-01

    Full Text Available Este trabalho traz um estudo da Divisão de Tratamento Técnico da Informação do Sistema Integrado de Bibliotecas do Município de São Carlos (SIBI/SC. O objetivo é mapear os processos do setor de processamento técnico do material bibliográfico do sistema, desde sua aquisição até sua disponibilização para o usuário. Para isto, fez uso da modelagem de processos de negócios.  A metodologia empregada foi a pesquisa-ação e bibliográfica. Como resultado do mapeamento foram identificados pontos críticos e propostas soluções, visando a melhoria dos serviços prestados no Sistema Integrado de Bibliotecas do Município de São Carlos. Abstract: This paper presents a study from Division of Information Technical Treatment belonging to the Library Integrated System of São Carlos City (SIBI-SC. Technical Treatment is responsible for receiving works, classification and indexing, tipping, availability on the collection and inventory of all library materials of system integrators libraries. The aim is to map the processes from division of technical treatment of the system, since its acquisition to its availability to the user. For such, the study applied the business process modeling approach. The methodological procedures used in the research include action research and bibliographic research. The result of mapping identified critical points for which solutions were proposed, aiming to improve the services provided by the system. Keywords: Library. BPM. Business processes management. Public management. Process integration. Process mapping. Resumen: En este trabajo se presenta un estudio de la División de Tratamiento Técnico de Información del Sistema Integrado de Biblioteca en São Carlos / SP (SIBI-SC. Tratamiento Técnico se encarga de recibir las obras, la clasificación y la indexación, la propina, disponible en los activos e inventario de todos los materiales de la biblioteca de las bibliotecas integradores de sistemas. El

  4. Laser Stripping via a Broad Stark State for a High-Intensity Proton Ring

    CERN Document Server

    Yamane, I; Takayama, K; Yamane, Isao; Suzuki, Toshikazu; Takayama, Ken

    2002-01-01

    A new type of charge-exchange injection scheme for high-intensity proton rings that use a laser beam and an undulator magnet is proposed. The elementary stripping process is resonant photoionization via a broad Stark state formed by the Stark effect at an energy level near the peak of the potential barrier. The method used to estimate the parameters of the necessary laser beam and magnetic field is described. As an application to an actual accelerator, a laser stripping system using a high-finesse Fabry-Perot resonator and an undulator is proposed. An estimation of the photon loss due to the pumping-up of H$^0$ atoms, tunability of the system and the emittance growth due to stripping in the undulator magnet is also given.

  5. LMFBR with booster pump in pumping loop

    Science.gov (United States)

    Rubinstein, H.J.

    1975-10-14

    A loop coolant circulation system is described for a liquid metal fast breeder reactor (LMFBR) utilizing a low head, high specific speed booster pump in the hot leg of the coolant loop with the main pump located in the cold leg of the loop, thereby providing the advantages of operating the main pump in the hot leg with the reliability of cold leg pump operation.

  6. Heat pump technology

    CERN Document Server

    Von Cube, Hans Ludwig; Goodall, E G A

    2013-01-01

    Heat Pump Technology discusses the history, underlying concepts, usage, and advancements in the use of heat pumps. The book covers topics such as the applications and types of heat pumps; thermodynamic principles involved in heat pumps such as internal energy, enthalpy, and exergy; and natural heat sources and energy storage. Also discussed are topics such as the importance of the heat pump in the energy industry; heat pump designs and systems; the development of heat pumps over time; and examples of practical everyday uses of heat pumps. The text is recommended for those who would like to kno

  7. Buffer strips in composites at elevated temperature

    Science.gov (United States)

    Bigelow, C. A.

    1983-01-01

    The composite material 'buffer strip' concept is presently investigated at elevated temperatures for the case of graphite/polyimide buffer strip panels using a (45/0/45/90)2S layup, where the buffer strip material was 0-deg S-glass/polyimide. Each panel was loaded in tension until it failed, and radiographs and crack opening displacements were recorded during the tests to determine fracture onset, fracture arrest, and the extent of damage in the buffer strip after crack arrest. At 177 + or - 3 C, the buffer strips increased the panel strength by at least 40 percent in comparison with panels without buffer strips. Compared to similar panels tested at room temperature, those tested at elevated temperature had lower residual strengths, but higher failure strains.

  8. Stripping, Sex, and Popular Culture

    OpenAIRE

    Roach, Catherine M.

    2007-01-01

    At the heart of Stripping, Sex, and Popular Culture lies a very personal story, of author Catherine Roach's response to the decision of her life-long best friend to become an exotic dancer. Catherine and Marie grew up together in Canada and moved to the USA to enroll in PhD programs at prestigious universities. For various reasons, Marie left her program and instead chose to work as a stripper. The author, at first troubled and yet fascinated by her friend's decision, follows Marie's journey ...

  9. 3D silicon strip detectors

    Energy Technology Data Exchange (ETDEWEB)

    Parzefall, Ulrich [Physikalisches Institut, Universitaet Freiburg, Hermann-Herder-Str. 3, D-79104 Freiburg (Germany)], E-mail: ulrich.parzefall@physik.uni-freiburg.de; Bates, Richard [University of Glasgow, Department of Physics and Astronomy, Glasgow G12 8QQ (United Kingdom); Boscardin, Maurizio [FBK-irst, Center for Materials and Microsystems, via Sommarive 18, 38050 Povo di Trento (Italy); Dalla Betta, Gian-Franco [INFN and Universita' di Trento, via Sommarive 14, 38050 Povo di Trento (Italy); Eckert, Simon [Physikalisches Institut, Universitaet Freiburg, Hermann-Herder-Str. 3, D-79104 Freiburg (Germany); Eklund, Lars; Fleta, Celeste [University of Glasgow, Department of Physics and Astronomy, Glasgow G12 8QQ (United Kingdom); Jakobs, Karl; Kuehn, Susanne [Physikalisches Institut, Universitaet Freiburg, Hermann-Herder-Str. 3, D-79104 Freiburg (Germany); Lozano, Manuel [Instituto de Microelectronica de Barcelona, IMB-CNM, CSIC, Barcelona (Spain); Pahn, Gregor [Physikalisches Institut, Universitaet Freiburg, Hermann-Herder-Str. 3, D-79104 Freiburg (Germany); Parkes, Chris [University of Glasgow, Department of Physics and Astronomy, Glasgow G12 8QQ (United Kingdom); Pellegrini, Giulio [Instituto de Microelectronica de Barcelona, IMB-CNM, CSIC, Barcelona (Spain); Pennicard, David [University of Glasgow, Department of Physics and Astronomy, Glasgow G12 8QQ (United Kingdom); Piemonte, Claudio; Ronchin, Sabina [FBK-irst, Center for Materials and Microsystems, via Sommarive 18, 38050 Povo di Trento (Italy); Szumlak, Tomasz [University of Glasgow, Department of Physics and Astronomy, Glasgow G12 8QQ (United Kingdom); Zoboli, Andrea [INFN and Universita' di Trento, via Sommarive 14, 38050 Povo di Trento (Italy); Zorzi, Nicola [FBK-irst, Center for Materials and Microsystems, via Sommarive 18, 38050 Povo di Trento (Italy)

    2009-06-01

    While the Large Hadron Collider (LHC) at CERN has started operation in autumn 2008, plans for a luminosity upgrade to the Super-LHC (sLHC) have already been developed for several years. This projected luminosity increase by an order of magnitude gives rise to a challenging radiation environment for tracking detectors at the LHC experiments. Significant improvements in radiation hardness are required with respect to the LHC. Using a strawman layout for the new tracker of the ATLAS experiment as an example, silicon strip detectors (SSDs) with short strips of 2-3 cm length are foreseen to cover the region from 28 to 60 cm distance to the beam. These SSD will be exposed to radiation levels up to 10{sup 15}N{sub eq}/cm{sup 2}, which makes radiation resistance a major concern for the upgraded ATLAS tracker. Several approaches to increasing the radiation hardness of silicon detectors exist. In this article, it is proposed to combine the radiation hard 3D-design originally conceived for pixel-style applications with the benefits of the established planar technology for strip detectors by using SSDs that have regularly spaced doped columns extending into the silicon bulk under the detector strips. The first 3D SSDs to become available for testing were made in the Single Type Column (STC) design, a technological simplification of the original 3D design. With such 3D SSDs, a small number of prototype sLHC detector modules with LHC-speed front-end electronics as used in the semiconductor tracking systems of present LHC experiments were built. Modules were tested before and after irradiation to fluences of 10{sup 15}N{sub eq}/cm{sup 2}. The tests were performed with three systems: a highly focused IR-laser with 5{mu}m spot size to make position-resolved scans of the charge collection efficiency, an Sr{sup 90}{beta}-source set-up to measure the signal levels for a minimum ionizing particle (MIP), and a beam test with 180 GeV pions at CERN. This article gives a brief overview of

  10. Dry vacuum pumps

    Science.gov (United States)

    Sibuet, R.

    2008-05-01

    For decades and for ultimate pressure below 1 mbar, oil-sealed Rotary Vane Pumps have been the most popular solution for a wide range of vacuum applications. In the late 80ies, Semiconductor Industry has initiated the development of the first dry roughing pumps. Today SC applications are only using dry pumps and dry pumping packages. Since that time, pumps manufacturers have developed dry vacuum pumps technologies in order to make them attractive for other applications. The trend to replace lubricated pumps by dry pumps is now spreading over many other market segments. For the Semiconductor Industry, it has been quite easy to understand the benefits of dry pumps, in terms of Cost of Ownership, process contamination and up-time. In this paper, Technology of Dry pumps, its application in R&D/industries, merits over conventional pumps and future growth scope will be discussed.

  11. Sviluppo e validazione di un antigene-capture ELISA basato su anticorpi monoclonali specifici per Listeria monocytogenes negli alimenti

    Directory of Open Access Journals (Sweden)

    Rossella Lelli

    2011-09-01

    Full Text Available È stato standardizzato e validato un dosaggio immunoenzimatico capture ELISA per l’identificazione di Listeria monocytogenes negli alimenti. Il dosaggio è stato messo a punto analizzando campioni di prodotti carnei, ittici e lattiero-caseari, pasta di semola e di farina di grano. Il metodo è risultato specifico al 100% per Listeria spp., con limite di rivelazione di 6,6 × 10(3 cfu/ml. Il metodo L. monocytogenes capture ELISA è stato confrontato con il metodo ufficiale ISO 11290-1:1996 per l’isolamento e l’identificazione di L. monocytogenes in matrici alimentari ottenendo un indice di concordanza significativo. Il dosaggio è stato validato in base alle indicazioni della norma ISO 16140:2003 relativamente ai metodi di analisi qualitativi. Il dosaggio è risultato accurato, specifico, sensibile, selettivo, riproducibile e rapido da eseguire, consentendo nello screening degli alimenti la riduzione di tempi e costi dell’indagine microbiologica.

  12. Optimizing the Stripping Procedure for LHCb

    CERN Document Server

    Richardson, Rachel

    2017-01-01

    The LHCb experiment faces a major challenge from the large amounts of data received while the LHC is running. The ability to sort this information in a useful manner is important for working groups to perform physics analyses. Both hardware and software triggers are used to decrease the data rate and then the stripping process is used to sort the data into streams and further into stripping lines. This project studies the hundreds of stripping lines to look for overlaps between them in order to make the stripping process more efficient.

  13. Gerando Modelo de Negócio: a pré-incubação como ambiente experimental

    Directory of Open Access Journals (Sweden)

    Anderson Paiva Cruz

    2016-04-01

    Full Text Available Este estudo visa contribuir para a construção de um modelo de monitoramento e avaliação que possibilite um melhor acompanhamento das empresas na fase de pré-incubação em uma incubadora de base tecnológica da Universidade Federal do Rio Grande do Norte (UFRN. O modelo de monitoramento e avaliação foi estruturado de acordo com o programa definido para a pré-incubação da incubadora. Na etapa de pré-incubação a incubadora tem a função de apoiar empreendedores a transformarem ideias inovadoras em negócios rentáveis e, para isso, oferece cursos e mentorias sobre Business Model Generation (BMG; Design Thinking Startup Enxuta; Estratégia do Oceano Azul; Métricas e Indicadores; e Pitch. A forma de acompanhamento dos empreendedores concilia os conceitos apresentados nos módulos do curso com as etapas de construção do BMG, desenvolvimento do protótipo e validação do negócio proposto pelos empreendedores. Metodologicamente, trata-se de uma pesquisa exploratória, com abordagem qualitativa, sendo utilizada a Pesquisa-ação para o modelo de acompanhamento das empresas e definição dos módulos do curso.A definição de um modelo padrão para acompanhamento e avaliação das empresas pré-incubadas permitiu um acompanhamento mais preciso do estágio de desenvolvimento da empresa e possibilitou que a incubadora pudesse cumprir seu papel de forma mais eficiente.

  14. Solidification Structure of Low Carbon Steel Strips with Different Phosphorus Contents Produced by Strip Casting

    Institute of Scientific and Technical Information of China (English)

    Na LI; Zhenyu LIU; Yiqing QIU; Zhaosen LIN; Xianghua LIU; Guodong WANG

    2006-01-01

    In the present paper, low carbon steel strips with different phosphorus contents were produced using a twin roll strip casting process. The solidification structure was studied and its features were analyzed in detail. It was found that the strips possessed a fine microstructure compared with the mould cast steels. With increasing phosphorus content more ferrite has been formed with finer grains.

  15. LINAC 3 experiment: This experiment is used to study some scenarios of the future LEIR (low-energy ion ring) vacuum design.

    CERN Multimedia

    Maximilien Brice

    2002-01-01

    Photo 1 316LN stainless steel sheet 0.7 m thick sheet metal, with water-jet cut holes; before (sheet metal) and after rolling (tube). Photo 2 316LN stainless steel tube with water-jet cut holes. Photo 3 Inner tube is fitted with NEG (non-evaporable getter) strips, creating a kind of total NEG pump. Photo 4 Inner tube is fitted with NEG (non-evaporable getter) strips, creating a kind of total NEG pump. Photo 5 Same tubes but compiled on top of each other. Photo 6 The stack of tubes is put into a vacuum chamber that will be used in the LINAC 3 experiment during summer 2002 (lead-ion beam will be used for this experiment). The holes allow all-round pumping, i.e. close to the vacuum chamber walls.

  16. Centrifugal pump handbook

    CERN Document Server

    Pumps, Sulzer

    2010-01-01

    This long-awaited new edition is the complete reference for engineers and designers working on pump design and development or using centrifugal pumps in the field. This authoritative guide has been developed with access to the technical expertise of the leading centrifugal pump developer, Sulzer Pumps. In addition to providing the most comprehensive centrifugal pump theory and design reference with detailed material on cavitation, erosion, selection of materials, rotor vibration behavior and forces acting on pumps, the handbook also covers key pumping applications topics and operational

  17. Hardy inequalities in strips on ruled surfaces

    Directory of Open Access Journals (Sweden)

    2006-01-01

    Full Text Available We consider the Dirichlet Laplacian in infinite two-dimensional strips defined as uniform tubular neighbourhoods of curves on ruled surfaces. We show that the negative Gauss curvature of the ambient surface gives rise to a Hardy inequality and we use this to prove certain stability of spectrum in the case of asymptotically straight strips about mildly perturbed geodesics.

  18. Tactual Strip Maps as Navigational Aids.

    Science.gov (United States)

    Golledge, R. G.

    1991-01-01

    This article reviews the history and use of tactual maps by blind and visually impaired travelers. It discusses textual patterns, symbols, and graphics; differences between conventional geographic-cartographic maps and strip maps used as navigational aids; and current advances, including disposable, quick-to-produce, and easy-to-update strip maps.…

  19. Water problems in Gaza Strip,Palestine

    Institute of Scientific and Technical Information of China (English)

    Ismail ALGHALBAN

    2001-01-01

    The only source for water in Gaza strip, southern Palestine, is the groundwater aquifer. The Pliocene - Pleistocene aquifer has two serious problems: quantity and quality. This study is an attempt to identify the problems and to suggest solutions for water problems in Gaza strip. In addition, some rules for rehabilitation of the aquifers were suggested.

  20. 7 CFR 29.6041 - Strips.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Strips. 29.6041 Section 29.6041 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... INSPECTION Standards Definitions § 29.6041 Strips. The sides of a tobacco leaf from which the stem has...

  1. Outgassing measurement of an LHC collimator and estimation for the NEG performances

    CERN Document Server

    Kamiya, Junichiro; Jimenez, J M; Bregliozzi, G

    2011-01-01

    The outgassing rate of the collimators in the Large Hadron Collider (LHC) at CERN has an important role for the life-time of the Non-Evaporable Getter (NEC), and an accurate analysis allows the definition of future activities, like NEC vacuum activation. For these reasons, both, total outgassing rate and gas composition of a secondary collimator have been measured in the laboratory. The outgassing rate decreases by about two orders of magnitude by after bake-out and moreover, repeated bake-out further reduced the outgassing rate. The gas transmission through the NEC coated beam pipes and the resulting pressure distributions near the collimator were also measured in a dedicated setup. It is found that the main gas component after just 2 m of NEC coated beam pipe is CH(4) due to the extreme pumping speed of NEC for the other gases. Large amount of outgassing for H(2) and carbon related molecules are released when moving the collimator jaws. It is found that the NEC is very effective even in such case with large...

  2. Alternative backing up pump for turbomolecular pumps

    Science.gov (United States)

    Myneni, Ganapati Rao

    2003-04-22

    As an alternative to the use of a mechanical backing pump in the application of wide range turbomolecular pumps in ultra-high and extra high vacuum applications, palladium oxide is used to convert hydrogen present in the evacuation stream and related volumes to water with the water then being cryo-pumped to a low pressure of below about 1.e.sup.-3 Torr at 150.degree. K. Cryo-pumping is achieved using a low cost Kleemenco cycle cryocooler, a somewhat more expensive thermoelectric cooler, a Venturi cooler or a similar device to achieve the required minimization of hydrogen partial pressure.

  3. Circuit realization microwave antennas-oscillator on strip antennas

    OpenAIRE

    Golynskyy, V. D.; Prudyus, I. N.

    2009-01-01

    Showing special feature of development circuitries microwave transistors antennasoscillator on strip dielectric-resonator-antennas. Showing circuitries and technical characteristics of developed microwave antennasoscillator on strip.

  4. Large electromagnetic pumps. [LMFBR

    Energy Technology Data Exchange (ETDEWEB)

    Kilman, G.B.

    1976-01-01

    The development of large electromagnetic pumps for the liquid metal heat transfer systems of fission reactors has progressed for a number of years. Such pumps are now planned for fusion reactors and solar plants as well. The Einstein-Szilard (annular) pump has been selected as the preferred configuration. Some of the reasons that electromagnetic pumps may be preferred over mechanical pumps and why the annular configuration was selected are discussed. A detailed electromagnetic analysis of the annular pump, based on slug flow, is presented. The analysis is then used to explore the implications of large size and power on considerations of electromagnetic skin effect, geometric skin effect and the cylindrical geometry.

  5. Transfusion and blood donation in comic strips.

    Science.gov (United States)

    Lefrère, Jean-Jacques; Danic, Bruno

    2013-07-01

    The representation of blood transfusion and donation of blood in the comic strip has never been studied. The comic strip, which is a relatively recent art, emerged in the 19th century before becoming a mass medium during the 20th century. We have sought, by calling on collectors and using the resources of Internet, comic strips devoted, wholly or in part, to the themes of transfusion and blood donation. We present some of them here in chronologic order, indicating the title, country of origin, year of publication, and names of authors. The theme of the superhero using transfusion to transmit his virtues or his powers is repeated throughout the 20th century in North American comic strips. More recently, comic strips have been conceived from the outset with a promotional aim. They perpetuate positive images and are directed toward a young readership, wielding humor to reduce the fear of venipuncture. Few comic strips denounce the abuse of the commercialization of products derived from the human body. The image of transfusion and blood donation given by the comic strips is not to be underestimated because their readership is primarily children, some of whom will become blood donors. Furthermore, if some readers are transfused during their lives, the impact of a memory more or less conscious of these childhood readings may resurface, both in hopes and in fears.

  6. A Strip Cell in Pyroelectric Devices

    Directory of Open Access Journals (Sweden)

    An-Shen Siao

    2016-03-01

    Full Text Available The pyroelectric effect affords the opportunity to convert temporal temperature fluctuations into usable electrical energy in order to develop abundantly available waste heat. A strip pyroelectric cell, used to enhance temperature variation rates by lateral temperature gradients and to reduce cell capacitance to further promote the induced voltage, is described as a means of improving pyroelectric energy transformation. A precision dicing saw was successfully applied in fabricating the pyroelectric cell with a strip form. The strip pyroelectric cell with a high-narrow cross section is able to greatly absorb thermal energy via the side walls of the strips, thereby inducing lateral temperature gradients and increasing temperature variation rates in a thicker pyroelectric cell. Both simulation and experimentation show that the strip pyroelectric cell improves the electrical outputs of pyroelectric cells and enhances the efficiency of pyroelectric harvesters. The strip-type pyroelectric cell has a larger temperature variation when compared to the trenched electrode and the original type, by about 1.9 and 2.4 times, respectively. The measured electrical output of the strip type demonstrates a conspicuous increase in stored energy as compared to the trenched electrode and the original type, by of about 15.6 and 19.8 times, respectively.

  7. High energy H- ion transport and stripping

    Energy Technology Data Exchange (ETDEWEB)

    Chou, W.; /Fermilab

    2005-05-01

    During the Proton Driver design study based on an 8 GeV superconducting RF H{sup -} linac, a major concern is the feasibility of transport and injection of high energy H{sup -} ions because the energy of H{sup -} beam would be an order of magnitude higher than the existing ones. This paper will focus on two key technical issues: (1) stripping losses during transport (including stripping by blackbody radiation, magnetic field and residual gases); (2) stripping efficiency of carbon foil during injection.

  8. THE DEVELOPMENT OF FCC STRIPPING TECHNOLOGY

    Institute of Scientific and Technical Information of China (English)

    ZHANGZhen-qian

    2003-01-01

    This article briefly describes the major patents domestic and the abroad,and the current situation and achievements of FCC stripping technology in China.The develping trend of FCC stripping technology is presented,including further developments of FCC stripper to improve unit performance,combination of the stripper and pre-stripper within disengager to from a complete high-efficiency FCC stripping system.In addition to high efficiency,simple structure and easiness of installation and maintenance for a new FCC stripper are all of consideration.

  9. Saving Energy Through Advanced Power Strips (Poster)

    Energy Technology Data Exchange (ETDEWEB)

    Christensen, D.

    2013-10-01

    Advanced Power Strips (APS) look just like ordinary power strips, except that they have built-in features that are designed to reduce the amount of energy used by many consumer electronics. There are several different types of APSs on the market, but they all operate on the same basic principle of shutting off the supply power to devices that are not in use. By replacing your standard power strip with an APS, you can signifcantly cut the amount of electricity used by your home office and entertainment center devices, and save money on your electric bill. This illustration summarizes the different options.

  10. Pump element for a tube pump

    DEFF Research Database (Denmark)

    2011-01-01

    The invention relates to a tube pump comprising a tube and a pump element inserted in the tube, where the pump element comprises a rod element and a first and a second non-return valve member positioned a distance apart on the rod element. The valve members are oriented in the same direction rela...... to a part of the tube. The invention further relates to a method for creating a flow of a fluid within an at least partly flexible tube by means of a pump element as mentioned above.......The invention relates to a tube pump comprising a tube and a pump element inserted in the tube, where the pump element comprises a rod element and a first and a second non-return valve member positioned a distance apart on the rod element. The valve members are oriented in the same direction...... portion acts to alternately close and open the valve members thereby generating a fluid flow through the tube. The invention further relates to a pump element comprising at least two non-return valve members connected by a rod element, and for insertion in an at least partly flexible tube in such tube...

  11. TLR5 signaling stimulates the innate production of IL-17 and IL-22 by CD3negCD127+ immune cells in spleen and mucosa1

    Science.gov (United States)

    Van Maele, Laurye; Carnoy, Christophe; Cayet, Delphine; Songhet, Pascal; Dumoutier, Laure; Ferrero, Isabel; Janot, Laure; Erard, François; Bertout, Julie; Leger, Hélène; Sebbane, Florent; Benecke, Arndt; Renauld, Jean-Christophe; Hardt, Wolf-Dietrich; Ryffel, Bernhard; Sirard, Jean-Claude

    2010-01-01

    In adaptive immunity, T helper-17 lymphocytes produce the IL-17 and IL-22 cytokines that stimulate mucosal antimicrobial defenses and tissue repair. Here, we observed that the TLR5 agonist flagellin induced swift and transient transcription genes encoding IL-17 and IL-22 in lymphoid, gut and lung tissues. This innate response also temporarily enhanced the expression of genes associated with the antimicrobial Th17 signature. The source of the Th17-related cytokines was identified as novel populations of CD3negCD127+ immune cells among which CD4-expressing cells resembling lymphoid tissue inducer cells. We also demonstrated that dendritic cells are essential for expression of Th17-related cytokines and so for stimulation of innate cells. These data define that TLR-induced activation of CD3negCD127+ cells and production of Th17-related cytokines may be crucial for the early defenses against pathogen invasion of host tissues. PMID:20566828

  12. Modelos de negócios para periódicos científicos eletrônicos de acesso aberto.

    OpenAIRE

    Katiúcia Araujo Gumeiro

    2011-01-01

    Trata-se de uma pesquisa que estuda o uso de modelos de negócios no contexto da publicação de periódicos científicos eletrônicos de acesso aberto, em que as diferenças disciplinares são consideradas, especificamente quanto às seguintes questões: velocidades de publicação exigidas, financiamentos e particularidades que envolvem a edição de um periódico científico. Tem como objetivo elaborar um modelo que permita identificar os elementos necessários para configurar um modelo de negócios adequad...

  13. O Paradigma Pós-Moderno Do Negócio Jurídico E A Necessidade De Uma Nova Concepção Na Contemporaneidade

    Directory of Open Access Journals (Sweden)

    Ana Claudia Corrêa Zuin Mattos do Amaral

    2017-07-01

    Full Text Available A objetivo desta pesquisa consiste na demonstração de que se faz necessária a superação dos paradigmas clássico e moderno do negócio jurídico na contemporaneidade, sobretudo em razão da infinidade de novas situações jurídicas apresentadas pelo mundo atual, notadamente no campo da tecnologia e da biomedicina, de modo que o direito não tem conseguido mais abarcar a real definição de negócio jurídico, que, por sua vez, não mais possui conotação apenas patrimonial. O método empregado será o dedutivo.

  14. Proton pump inhibitors

    Science.gov (United States)

    Proton pump inhibitors (PPIs) are medicines that work by reducing the amount of stomach acid made by ... Proton pump inhibitors are used to: Relieve symptoms of acid reflux, or gastroesophageal reflux disease (GERD). This ...

  15. 缩短1620t/dCO_2气提尿素工艺熔融尿液泵倒运时间%Shortening Transport Time of Melting Urea Liquid Pump in 1620T/D Carbon Dioxide Gas Stripping Urea Process

    Institute of Scientific and Technical Information of China (English)

    肖锡骏

    2012-01-01

    From the daily maintenance of production, through a simple technical improvement, the problem of evaporation system to transport device needed to stop melt urea pump was solved. Through transporting melt urea pump online, the transportation time was shortened, evaporation circulating long time was uret was reduced, consumption of steam and CO2 was decreased, with improved quality pass, reduced production cost. avoided, generation of bi- of product and percent of%从日常生产维护出发,通过技术改造解决了装置需停蒸发系统才能倒运熔融尿液泵的难题,通过在线倒运熔融尿液泵,缩短了倒运时间,避免了蒸发长时间打循环,减少成品缩二脲的生成,降低了蒸汽耗量和CO2耗量,提高了产品质量合格率,降低了生产成本。

  16. Entendendo a Pegada da VBR nos Estudos em Negócios Internacionais: os Últimos Vinte Anos de Pesquisa

    Directory of Open Access Journals (Sweden)

    Manuel Aníbal Silva Portugal Vasconcelos Ferreira

    2014-01-01

    Full Text Available A pesquisa em Negócios Internacionais (IB – International Business evoluiu substancialmente ao longo das últimas quatro década s, incorporando novas questões e contribuições teóricas. Durante as últimas duas déc adas, a Visão Baseada em Recursos (RBV - Resource-Based View conquistou a preferência de vários pesquisadores em negócios internacionais e se tornou gradualmente uma das per spectivas teóricas dominantes para estudar decisões e operações de IB. O artigo de 199 1 “ Firm resources and sustained competitive advantage” ( “ Recursos internos e vantagem competitiva sustentada ” de Jay Barney é reconhecido como uma contribuição fundamen tal para a Visão Baseada em Recursos (RBV. Neste artigo avaliamos a influência da RBV, guiados pelo artigo de Jay Barney (1991, sobre pesquisa em negócios internaci onais ao longo de um período de vinte anos, de 1991 a 2010. Neste estudo bibliométrico do s artigos publicados no periódico líder para a pesquisa em negócios internacionais – o Journal of International Business Studies (JIBS – conduzimos análises de citações e de cocit ações, das redes de coautoria e aprofundamos a análise dos tópicos-chave de pesquis a. Além de entender a pesquisa existente, também contribuímos para identificar per spectivas para pesquisa futura.

  17. Inapproximability of maximal strip recovery

    CERN Document Server

    Jiang, Minghui

    2009-01-01

    In comparative genomic, the first step of sequence analysis is usually to decompose two or more genomes into syntenic blocks that are segments of homologous chromosomes. For the reliable recovery of syntenic blocks, noise and ambiguities in the genomic maps need to be removed first. Maximal Strip Recovery (MSR) is an optimization problem proposed by Zheng, Zhu, and Sankoff for reliably recovering syntenic blocks from genomic maps in the midst of noise and ambiguities. Given $d$ genomic maps as sequences of gene markers, the objective of \\msr{d} is to find $d$ subsequences, one subsequence of each genomic map, such that the total length of syntenic blocks in these subsequences is maximized. For any constant $d \\ge 2$, a polynomial-time 2d-approximation for \\msr{d} was previously known. In this paper, we show that for any $d \\ge 2$, \\msr{d} is APX-hard, even for the most basic version of the problem in which all gene markers are distinct and appear in positive orientation in each genomic map. Moreover, we provi...

  18. A video strip chart program

    Energy Technology Data Exchange (ETDEWEB)

    Jones, N.L. [Oak Ridge National Lab., TN (United States). Accelerator-Based Atomic Physics

    1994-12-31

    A strip chart recorder has been utilized for trend analysis of the Oak Ridge National Laboratory EN tandem since 1987. At the EN, the author could not afford the nice eight channel thermal pen recorder that was used at the 25 URC. He had to suffice with two channel fiber tip or capillary pen type recorders retrieved from salvage and maintained with parts from other salvaged recorders. After cycling through several machines that eventually became completely unserviceable, a search for a new thermal recorder was begun. As much as he hates to write computer code, he decided to try his hand at getting an old data acquisition unit, that had been retrieved several years ago from salvage, to meet his needs. A BASIC language compiler was used because time was not available to learn a more advanced language. While attempting to increase acquisition and scroll speed on the 6 MHz 80286 that the code was first developed on, it became apparent that scrolling only the first small portion of the screen at high speed and then averaging that region and histogramming the average provided both the speed necessary for capturing fairly short duration events, and a trend record without use of back scrolling and disk storage routines. This turned out to be quite sufficient.

  19. Folga Organizacional em Unidades de Negócios de Empresa Descentralizada na Percepção dos Controllers

    Directory of Open Access Journals (Sweden)

    Ilse Maria Beuren

    2013-05-01

    Full Text Available O estudo objetiva examinar determinantes da folga organizacional em unidades de negócios (UN de empresa descentralizada na percepção dos controllers. Pesquisa descritiva, com abordagem qualitativa, foi realizada por meio de um estudo de caso em cinco UN de empresa multinacional do setor de embalagens. Entrevista estruturada foi realizada com os controllers da UN do Brasil e de quatro UN dos Estados Unidos, pautada no instrumento de pesquisa de Indjejikian e Matejka (2006. Na análise de conteúdo das respostas constata-se a existência de folga organizacional em maior ou menor proporção no alcance das metas orçamentárias; nas informações disponibilizadas sob o enfoque da assimetria entre o gerente geral da unidade e o controller corporativo; na autoridade das decisões relativas à gestão de pessoas e de mudanças nas técnicas e procedimentos contábeis; e na autonomia das UN. Conclui-se que os quatro determinantes da folga organizacional identificados na pesquisa de Indjejikian e Matejka (2006 também possuem relativa presença nas UN da empresa pesquisada, o que justifica ampliar o estudo para outras empresas e de futuras pesquisas explorar motivações para a folga organizacional e de novos determinantes.

  20. I sistemi biometrici lo sviluppo dei mercati negli Usa, UE e nel mondo. La normativa frena quello italiano

    Directory of Open Access Journals (Sweden)

    Franco Zucchetti

    2007-04-01

    Full Text Available Negli ultimi anni il settore biometrico sta compiendo, a livello mondiale, importanti passi in avanti soprattutto in termini di sviluppo e di diffusione. Questo trend positivo riguarda il mondo anglosassone e, in particolare, la realtà statunitense dove i sistemi biometrici vengono utilizzati, nelle più svariate situazioni, sia come controllo della sicurezza fisica delle persone, sia come terminali per l’autorizzazione all’accesso. La stessa diffusione non è riscontrabile nella maggior parte dei Paesi europei e in Italia dove raffrontiamo una realtà assai atipica nella quale la biometria fa un gran parlare di sé ma, in concreto, viene utilizzata con molta difficoltà. Tuttavia, un punto di contatto tra tutti gli attori europei ed extraeuropei può essere individuato nello sviluppo del settore relativo al riconoscimento biometrico applicato ai passaporti ed alle carte di identità. Il processo di globalizzazione ha generato, infatti, grandi masse di individui in continuo e costante movimento da un Paese all’altro e, contestualmente, ha prodotto una crescente domanda di sicurezza soprattutto nei confronti della minaccia terroristica. Appare chiaro, quindi, come l’identificazione certa delle persone diventi una necessità e debba presentare tecnologie simili per essere utilizzate ovunque.

  1. Analysis of the impact of studies published by Internext - Revista Eletrônica de Negócios Internacionais

    Directory of Open Access Journals (Sweden)

    Carlos Luis González-Valiente

    2015-08-01

    Full Text Available This is a citation analysis of the journal InternexT-Revista Eletrônica de Negócios Internacionais to determine the impact caused by studies published from 2006 to 2013. The software Publish or Perish (PoP was used, which retrieves articles and citations from the Google Scholar database. Among the indicators applied were: distribution of authors per article, citations per year, citation versus self-citation, citable journals versus non-citable documents, citation of the journal versus uncited documents, co-word analysis and h-index. 131 articles were obtained with a total of 153 citations received until June 2014. The articles tend to have multiple authors and an upward trend in citations was detected. The levels of self-citation were very low and most of the citing sources are Brazilian journals. There were more uncited than cited articles and those published during the first years (2006-2008 caused a larger impact.  The most cited articles are related to the topics of internationalization theory and strategy, transaction analysis and corporative governance. The h-index according to PoP is 6 and the g-index is 9.

  2. Pump for Saturated Liquids

    Science.gov (United States)

    Elliott, D. G.

    1986-01-01

    Boiling liquids pumped by device based on proven components. Expanding saturated liquid in nozzle and diverting its phases along separate paths in liquid/vapor separator raises pressure of liquid. Liquid cooled in process. Pump makes it unnecessary to pressurize cryogenic liquids in order to pump them. Problems of introducing noncondensable pressurizing gas avoided.

  3. Modelo de Negócio: Uma Abordagem Evolutiva no Setor de SVA sob a Ótica do Método Canvas.

    Directory of Open Access Journals (Sweden)

    Fábio Luiz Zandoval Bonazzi

    2015-11-01

    Full Text Available Este estudo objetivou analisar e descrever o modelo de negócios da empresa Movile e sua forma de criação e captura de valor. Trata-se de uma pesquisa qualitativa com foco empírico, baseada em um estudo de caso único realizado por meio de entrevista, análise documental e observações indiretas da empresa. O estudo permitiu analisar a concepção do modelo de negócio atual da empresa com base em todo em seu processo evolutivo delineado pelas alterações vivenciadas pelo segmento de serviço de valor agregado – SVA na última década, além de inferir sobre sua participação na cadeia de valor no setor de telecomunicações e descrever as nove dimensões de seu modelo de acordo com o Business Model Canvas – BMC (OSTERWALDER E PIGNEUR, 2010. Como contribuição teórica destaca-se a aproximação de antigos autores como Penrose (2006 e Chandler Jr. (2000 com o tema modelo de negócio, bem como o dinamismo que os mesmos puderam fornecer à ferramenta CANVAS, essencialmente caracterizada como um método estático, a partir da discussão do processo evolutivo organizacional.

  4. Plaque accumulations caused by interdental stripping.

    Science.gov (United States)

    Radlanski, R J; Jäger, A; Schwestka, R; Bertzbach, F

    1988-11-01

    Human enamel surfaces were stripped with orthodontic grinding and finishing materials, and evaluated with the scanning electron microscope (SEM). Even under in vitro conditions with the finest finishing strips, it was not possible to produce an enamel surface free of the furrows that result from the initial abrasion caused by the coarse strip. Enamel surfaces stripped gradually from coarse to superfine were left in the mouths of patients for 12 weeks and evaluated with the SEM. The edges of the furrows were found to be smoother but the furrows remained wide and deep enough to facilitate more plaque accumulations than those on untreated surfaces. The use of dental floss did not result in prevention of plaque accumulations along the bottom of the furrows.

  5. Finite element modeling of corneal strip extensometry

    CSIR Research Space (South Africa)

    Botha, N

    2012-12-01

    Full Text Available numerically modelled in several studies, this study focusses on accurately modelling the strip extensiometry test. Two methods were considered to simulate the experimental conditions namely, a single phase and a two phase method. A finite element model...

  6. Use of Mini-Sprinklers to Strip Trichloroethylene and Tetrachloroethylene from Contaminated Ground Water.

    Energy Technology Data Exchange (ETDEWEB)

    Brerisford, Yvette, C.; Bush, Parshall, B.; Blake, John, I.; Bayer, Cassandra L.

    2003-01-01

    Berisford, Y.C., P.B. Bush, J.I. Blake, and C.L. Bayer. 2003. Use of mini-sprinklers to strip trichloroethylene and tetrachloroethylene from contaminated ground water. J. Env. Qual. 32:801-815. Three low-volume mini-sprinklers were tested for their efficacy to strip trichloroethylene (TCE) and tetrachloroethylene (PCE) from water. Deionized water spiked with TCE and PCE was pumped through a mini-sprinkler supported on top of a 1.8-m-tall. Water was collected in collection vessels at 0.61 and 1.22 m above the ground on support columns that were spaced at 0.61-m intervals from the riser base, and samples were composited per height and distance from the riser. Overall, air-stripping reduced dissolved concentrations of TCE and PCE by 99.1 to 100 and 96.9 to 100%, respectively. Mini-sprinklers offer the advantages of (i) easy setup in series that can be used on practically any terrain; (ii) operation over a long period of time that does not threaten aquifer depletion; (iii) use in small or confined aquifers in which the capacity is too low to support large irrigation or pumping systems; and (iv) use in forests in which the small, low-impact droplets of the mini-sprinklers do not damage bark and in which trees can help manage (via evapotransporation) excess waste water.

  7. Strip Casting of High Performance Structural Alloys

    Institute of Scientific and Technical Information of China (English)

    S S Park; J G Lee; Nack J Kim

    2004-01-01

    There exists a great need for the development of high performance alloys due to increasing demands for energy conservation and environmental protection. Application of strip casting shows a strong potential for the improvement of properties of existing alloys and also for the development of novel alloy systems with superior properties. The present paper reviews our Center's activities in the development of high performance alloys by strip casting. Examples include (1) Al alloys, (2) wrought Mg alloys, and (3) bulk metallic glass (BMG) alloys.

  8. Speed Control and Coiling Temperature Control of Strip

    Institute of Scientific and Technical Information of China (English)

    CAI Xiao-hui; ZHANG Dian-hua; WANG Guo-dong; LIU Xiang-hua; FAN Lei

    2004-01-01

    Considering the strip speed during controlled laminar cooling on Baosteel 1580 hot strip mill in China, the influence of strip speed fluctuation on coiling temperature control for the tail and "neck" of the strip was analyzed. The optimization strategies were put forward and proved effective in operation.

  9. Excess Production Capacity Squeezes Profits of Brass Strip Enterprises

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    <正>Between 2003 and 2006,under the backdrop of rapid growth of domestic demand for brass strip and soaring copper price,brass strip manufacturers made a fortune.And brass strip manufacturers mushroomed in Zhejiang,Anhui and Jiangsu.Large brass strip manufacturers

  10. Process development of thin strip steel casting

    Energy Technology Data Exchange (ETDEWEB)

    Sussman, R.C.; Williams, R.S.

    1990-12-01

    An important new frontier is being opened in steel processing with the emergence of thin strip casting. Casting steel directly to thin strip has enormous benefits in energy savings by potentially eliminating the need for hot reduction in a hot strip mill. This has been the driving force for numerous current research efforts into the direct strip casting of steel. The US Department of Energy initiated a program to evaluate the development of thin strip casting in the steel industry. In earlier phases of this program, planar flow casting on an experimental caster was studied by a team of engineers from Westinghouse Electric corporation and Armco Inc. A subsequent research program was designed as a fundamental and developmental study of both planar and melt overflow casting processes. This study was arranged as several separate and distinct tasks which were often completed by different teams of researchers. An early task was to design and build a water model to study fluid flow through different designs of planar flow casting nozzles. Another important task was mathematically modeling of melt overflow casting process. A mathematical solidification model for the formation of the strip in the melt overflow process was written. A study of the material and conditioning of casting substrates was made on the small wheel caster using the melt overflow casting process. This report discusses work on the development of thin steel casting.

  11. Process development of thin strip steel casting

    Energy Technology Data Exchange (ETDEWEB)

    Sussman, R.C.; Williams, R.S.

    1990-12-01

    An important new frontier is being opened in steel processing with the emergence of thin strip casting. Casting steel directly to thin strip has enormous benefits in energy savings by potentially eliminating the need for hot reduction in a hot strip mill. This has been the driving force for numerous current research efforts into the direct strip casting of steel. The US Department of Energy initiated a program to evaluate the development of thin strip casting in the steel industry. In earlier phases of this program, planar flow casting on an experimental caster was studied by a team of engineers from Westinghouse Electric corporation and Armco Inc. A subsequent research program was designed as a fundamental and developmental study of both planar and melt overflow casting processes. This study was arranged as several separate and distinct tasks which were often completed by different teams of researchers. An early task was to design and build a water model to study fluid flow through different designs of planar flow casting nozzles. Another important task was mathematically modeling of melt overflow casting process. A mathematical solidification model for the formation of the strip in the melt overflow process was written. A study of the material and conditioning of casting substrates was made on the small wheel caster using the melt overflow casting process. This report discusses work on the development of thin steel casting.

  12. Nonuniform electro-osmotic flow on charged strips and its use in particle trapping.

    Science.gov (United States)

    Liu, Shui-Jin; Hwang, Shyh-Hong; Wei, Hsien-Hung

    2008-12-02

    In this article, we investigate theoretically electro-osmotic flow set up by charged strips on an otherwise uncharged surface. Starting with a single-strip problem we demonstrate that for simple polynomial surface charge distributions several basic solutions can be derived in closed forms constituted by the analogous idea-flow solutions, which provide a more lucid way of revealing the flow features. These solutions reveal two types of flow topology: simple draining-in/pumping-out streaming and a pair of microvortices for symmetric and antisymmetric surface charge distributions, respectively. For an arbitrary surface charge distribution, more complicated flow structures can be found by the superposition of these basic solutions. We further extend the analysis to two uniformly charged strips and show how the flow characteristics vary with the strips' dimensions and surface zeta potentials. The far-field velocity behavior is also asymptotically identified and indicates that the hydrodynamic nature of the flow is typically long-range. An application to particle trapping with electro-osmotic vortices is also investigated theoretically for the first time. We show that in collaboration with short-range attraction effects the trapping can be facilitated by symmetric vortices with a converging stagnation point, but not by asymmetric vortices.

  13. Novel photoresist stripping technology using steam-water mixture*

    Institute of Scientific and Technical Information of China (English)

    Wang Lei; Hui Yu; Gao Chaoqun; Jing Yupeng

    2011-01-01

    A novel wet vapor photoresist stripping technology is developed as an alternative to dry plasma ashing and wet stripping. Experiments using this technology to strip hard baked SU-8 photoresist, aurum and chromium film are carried out. Then the images of stripping results are shown and the mechanism is analyzed and discussed.The most striking result of this experiment is that the spraying mixture of steam and water droplets can strip photoresist and even metal film with ease.

  14. Depletive stripping chronopotentiometry : a major step forward in electrochemical stripping techniques for metal ion speciation analysis

    NARCIS (Netherlands)

    Town, R.M.; Leeuwen, van H.P.

    2004-01-01

    A comparative evaluation of the utility of the various modes of stripping chronopotentiometry (SCP) for trace metal speciation analysis is presented in the broad context of stripping voltammetric techniques. The remarkable fundamental advantages of depletive SCP at scanned deposition potential (SSCP

  15. Predictive validity of measures of comorbidity in older community dwellers: the Insufficienza Cardiaca negli Anziani Residenti a Dicomano Study.

    Science.gov (United States)

    Di Bari, Mauro; Virgillo, Adriana; Matteuzzi, Daniela; Inzitari, Marco; Mazzaglia, Giampiero; Pozzi, Claudia; Geppetti, Pierangelo; Masotti, Giulio; Marchionni, Niccolò; Pini, Riccardo

    2006-02-01

    To compare the ability of five measures of comorbidity to predict mortality and incident disability in basic activities of daily living (BADLs) in unselected older persons. An assessment of the data obtained from the Insufficienza Cardiaca negli Anziani Residenti a Dicomano (ICARe Dicomano) Study, a longitudinal epidemiological survey on heart failure in older people. Dicomano, a small, rural town near Florence, Italy. The entire population aged 65 and older living in Dicomano, Italy, was enrolled in the ICARe Dicomano Study. At baseline (1995), comorbidity was quantified in 688 participants, based on clinical diagnoses, using disease count (DC), Charlson Comorbidity Index (CCI), Index of Co-Existent Diseases (ICED), and Geriatric Index of Comorbidity (GIC), or on drug use, using Chronic Disease Score (CDS). Incident ADL disability was assessed in 1999 and vital status in 2004. Mortality increased with the severity of comorbidity, with hazard ratios around 2 when comparing the highest and the lowest quartiles of DC, CCI, and ICED in Cox regressions adjusted for age, sex, and physical and cognitive performance. Prediction of mortality with GIC and CDS was only borderline significant. All measures predicted incident ADL disability; the strongest risk gradient (hazard ratio = 8.2 between the highest and lowest quartiles) was observed with ICED. Physical and, to a minor extent, cognitive performance added significantly to predicting mortality and incident BADL disability. All the measures of comorbidity predicted death and BADL disability in older community dwellers. DC, CCI, and ICED performed better than GIC and CDS. Physical performance measures are strong, independent contributors to the prediction of these outcomes.

  16. Práticas do CMMI® como regras de negócio CMMI® practices as business rules

    Directory of Open Access Journals (Sweden)

    Gisele P. Morgado

    2007-08-01

    Full Text Available A busca pela qualidade de software leva à adoção de boas práticas no processo do desenvolvimento de software, como as práticas especificadas pelo modelo de maturidade do CMMI. A implantação do CMMI, entretanto, constitui um processo penoso e demorado. Além disso, a qualidade deste processo afeta diretamente os resultados obtidos. Este artigo explora a possibilidade de formalização das práticas do CMMI através do seu mapeamento para Regras de Negócio. A viabilidade desta proposta é estudada através do mapeamento da parte do CMMI relativa à área Gerência de Requisitos. As vantagens desta abordagem encontram-se tanto no aumento da qualidade do processo de certificação/auditoria do CMMI, quanto na melhoria da qualidade do sistema de informação que apóia o processo de desenvolvimento de software.The search for software quality results in the adoption of best practices in the software development process, such as the practices specified by the CMMI maturity model. However, the CMMI implementation constitutes a difficult and slow process. Besides, the quality of such a process directly affects the results obtained. This article explores the possibility of formalizing the CMMI practices via their mapping into Business Rules. This proposal viability was studied through the mapping of the CMMI part that concerns the Requirements Management area. This approach implies in an improvement of the CMMI certification/audit process and of the information system that supports the software development process.

  17. Attivitá fisica extra-scolastica negli adolescenti: il ruolo dello stato socio-economico delle famiglie

    Directory of Open Access Journals (Sweden)

    G. Capelli

    2003-05-01

    Full Text Available

    Obiettivi: l’associazione fra stato socio-economico (SES ed attività fisica è poco indagata. Obiettivo del presente studio è quello di valutare la relazione tra attività fisica extra-scolastica di adolescenti scolarizzati e lo SES della famiglia di provenienza.

    Metodi: l’indagine ha previsto la somministrazione nel corso dell’anno scolastico 2002-2003 di un apposito questionario anonimo autocompilato, già validato in uno studio pilota, ad un campione di studenti delle scuole medie inferiori del Lazio (province di Roma, Frosinone e Latina.

    Risultati: hanno partecipato allo studio 1486 studenti di cui 756 maschi (50.9% e 730 femmine (49.1%. L’età dei partecipanti varia fra gli 11 ed i 15 anni (età mediana 12 anni. Il 72.7% degli studenti dichiara di svolgere attività fisica al di fuori della scuola. Il livello di istruzione dei genitori e la loro attività lavorativa sembrano avere un peso notevole sui determinanti dell’attività fisica negli studenti. Infatti, svolgono prevalentemente attività fisica extra-scolastica i figli di genitori manager/libero professionisti (OR = 3.29 e con un elevato livello educativo (OR = 10.38 per i figli di genitori laureati.

    Conclusioni: i risultati confermano quanto la situazione socio-economica delle famiglie sia in netta relazione con l’attività fisico-sportiva dei giovani. Tali risultati potranno essere utili per gli operatori scolastici e gli amministratori nell’ispirare e realizzare azioni volte a diminuire il divario esistente fra i giovani che hanno le possibilità economiche e svolgono attività sportiva extra-scolastica e quelli che, invece, appartenendo a famiglie svantaggiate, hanno minore accesso a tali attività.

  18. Effect of Load Distribution on Strip Crown in Hot Strip Rolling

    Institute of Scientific and Technical Information of China (English)

    Hongshuang DI; Jianzhong XU; Dianyao GONG; Xianghua LIU; Guodong WANG; Xiaoming HE; Liying BA

    2004-01-01

    In order to establish precision model, a software to calculate the strip crown of four-high hot rolling mill was developed by using affecting function method according to the strip crown calculation theory. The effect of work roll diameter, unit width rolling load, roll bending force, work roll crown, initial strip crown and reduction, etc, on load distribution effect rate was simulated by using the software. The results show that the load distribution effect rate increases with the increase of strip width, work roll diameter, unit width rolling load, roll bending force, work roll crown, initial strip crown and reduction. Based on the simulation results, base value of load distribution effect rate and fitting coefficients of six power polynomial of load distribution effect rate modification coefficient were determined considering all of the above parameters. A simplified mathematical model for calculating load distribution effect rate was established.

  19. Anodic stripping voltammetry of silver nanoparticles: aggregation leads to incomplete stripping.

    Science.gov (United States)

    Cloake, Samantha J; Toh, Her Shuang; Lee, Patricia T; Salter, Chris; Johnston, Colin; Compton, Richard G

    2015-02-01

    The influence of nanoparticle aggregation on anodic stripping voltammetry is reported. Dopamine-capped silver nanoparticles were chosen as a model system, and melamine was used to induce aggregation in the nanoparticles. Through the anodic stripping of the silver nanoparticles that were aggregated to different extents, it was found that the peak area of the oxidative signal corresponding to the stripping of silver to silver(I) ions decreases with increasing aggregation. Aggregation causes incomplete stripping of the silver nanoparticles. Two possible mechanisms of 'partial oxidation' and 'inactivation' of the nanoparticles are proposed to account for this finding. Aggregation effects must be considered when anodic stripping voltammetry is used for nanoparticle detection and quantification. Hence, drop casting, which is known to lead to aggregation, is not encouraged for preparing electrodes for analytical purposes.

  20. Development of floating strip micromegas detectors

    Energy Technology Data Exchange (ETDEWEB)

    Bortfeldt, Jonathan

    2014-04-28

    Micromegas are high-rate capable, high-resolution micro-pattern gaseous detectors. Square meter sized resistive strip Micromegas are foreseen as replacement of the currently used precision tracking detectors in the Small Wheel, which is part of the forward region of the ATLAS muon spectrometer. The replacement is necessary to ensure tracking and triggering performance of the muon spectrometer after the luminosity increase of the Large Hadron Collider beyond its design value of 10{sup 34} cm{sup -2}s{sup -1} around 2020. In this thesis a novel discharge tolerant floating strip Micromegas detector is presented and described. By individually powering copper anode strips, the effects of a discharge are confined to a small region of the detector. This reduces the impact of discharges on the efficiency by three orders of magnitude, compared to a standard Micromegas. The physics of the detector is studied and discussed in detail. Several detectors are developed: A 6.4 x 6.4 cm{sup 2} floating strip Micromegas with exchangeable SMD capacitors and resistors allows for an optimization of the floating strip principle. The discharge behavior is investigated on this device in depth. The microscopic structure of discharges is quantitatively explained by a detailed detector simulation. A 48 x 50 cm{sup 2} floating strip Micromegas is studied in high energy pion beams. Its homogeneity with respect to pulse height, efficiency and spatial resolution is investigated. The good performance in high-rate background environments is demonstrated in cosmic muon tracking measurements with a 6.4 x 6.4 cm{sup 2} floating strip Micromegas under lateral irradiation with 550 kHz 20 MeV proton beams. A floating strip Micromegas doublet with low material budget is developed for ion tracking without limitations from multiple scattering in imaging applications during medical ion therapy. Highly efficient tracking of 20 MeV protons at particle rates of 550 kHz is possible. The reconstruction of the

  1. Area specific stripping factors for AGS. A method for extracting stripping factors from survey data

    Energy Technology Data Exchange (ETDEWEB)

    Aage, H.K.; Korsbech, U. [Technical Univ. of Denmark (Denmark)

    2006-04-15

    In order to use Airborne Gamma-ray Spectrometry (AGS) for contamination mapping, for source search etc. one must to be able to eliminate the contribution to the spectra from natural radioactivity. This in general is done by a stripping technique. The parameters for performing a stripping have until recently been measured by recording gamma spectra at special calibration sites (pads). This may be cumbersome and the parameters may not be correct when used at low gamma energies for environmental spectra. During 2000-2001 DTU tested with success a new technique for Carborne Gamma-ray Spectrometry (CGS) where the spectra from the surveyed area (or from a similar area) were used for calculating the stripping parameters. It was possible to calculate usable stripping ratios for a number of low energy windows - and weak source signals not detectable by other means were discovered with the ASS technique. In this report it is shown that the ASS technique also works for AGS data, and it has been used for recent Danish AGS tests with point sources. (Check of calibration of AGS parameters.) By using the ASS technique with the Boden data (Barents Rescue) an exercise source was detected that has not been detected by any of the teams during the exercise. The ASS technique therefore seems to be better for search for radiation anomalies than any other method known presently. The experiences also tell that although the stripping can be performed correctly at any altitude there is a variation of the stripping parameters with altitude that has not yet been quite understood. However, even with the oddly variations the stripping worked as expected. It was also observed that one might calculate a single common set of usable stripping factors for all altitudes from the entire data set i.e. some average a, b and c values. When those stripping factors were used the stripping technique still worked well. (au)

  2. Modeling of continuous strip production by rheocasting

    Science.gov (United States)

    Matsumiya, T.; Flemings, M. C.

    1981-03-01

    A process was experimentally and mathematically modeled for continuous and direct production of metal strip from its molten state by the use of Rheocasting. The process comprises 1) continuous production of a Rheocast semisolid alloy, and 2) direct shaping of the semisolid into strip. Sn-15 pct Pb was used as the modeling alloy. Crack formation and surface quality of the strip produced depend on fraction solid and deformation force. Continuous, sound strip could be obtained with good surface quality when fraction solid was between 0.50 and 0.70 and deformation force did not exceed a given maximum. Sheet thickness depends on deformation force, fraction solid, rotor rate of Rheocaster and production line speed. At constant deformation force, sheet thickness increases as fraction solid increases, rotor rate decreases and line speed is reduced. Sheet thickness is larger in the center than in the edge, but the difference is reduced by applying edgers. Some segregation of lead toward the edges is observed, and the segregation increases as amount of deformation is increased. A mathematical model for heat flow, solidification and deformation was constructed. The model predicts the point of completion of solidification in the strip and sheet thickness as a function of deformation force and line speed. Calculations are in good agreement with experimental results.

  3. Modeling of continuous strip production by rheocasting

    Energy Technology Data Exchange (ETDEWEB)

    Matsumiya, T.; Flemings, M.C.

    1981-03-01

    A process was experimentally and mathematically modeled for continuous and direct production of metal strip from its molten state by the use of Rheocasting. The process comprises 1) continuous production of a Rheocast semisolid alloy, and 2) direct shaping of the semisolid into strip. Sn-15 pct Pb was used as the modeling alloy. Crack formation and surface quality of the strip produced depend on fraction solid and deformation force. Continuous, sound strip could be obtained with good surface quality when fraction solid was between 0.50 and 0.70 and deformation force did not exceed a given maximum. Sheet thickness depends on deformation force, fraction solid, rotor rate of Rheocaster and production line speed. At constant deformation force, sheet thickness increases as fraction solid increases, rotor rate decreases and line speed is reduced. Sheet thickness is larger in the center than in the edge, but the difference is reduced by applying edgers. Some segregation of lead toward the edges is observed, ad the segregation increases as amount of deformation is increased. A mathematical model for heat flow, solidification and deformation was constructed. The model predicts the point of completion of solidification in the strip and sheet thickness as a function of deformation force and line speed. Calculations are in good agreement with experimental results.

  4. Beam stripping extraction from the VINCY cyclotron

    Directory of Open Access Journals (Sweden)

    Ristić-Đurović Jasna L.

    2006-01-01

    Full Text Available The extraction system of a cyclotron guides an ion beam from a spiral acceleration orbit, through an extraction trajectory, into a high energy transport line. The two methods commonly used to direct an ion into the extraction path are deflection, by the electric field of an electrostatic deflector, and ion stripping, by a thin carbon foil. Compared to the electrostatic deflector system, the stripping extraction provides a fast and easy change of the extracted ion energy and is easier to manufacture operate, and maintain. However, the extraction trajectory and dynamics of an ion beam after stripping are highly dependant on the ion energy and specific charge. Thus, when a multipurpose machine such as the VINCY Cyclotron is concerned, it is far from easy to deliver a variety of ion beams into the same high energy transport line and at the same time preserve a reasonable compactness of the extraction system. The front side stripping extraction system of the VINCY Cyclotron provides high (~70 MeV and mid (~30 MeV energy protons, as well as a number of heavy ions in broad energy ranges. The back side stripping extraction system extracts low energy protons (~18 MeV and enables their simultaneous use with high energy protons at the front side of the machine.

  5. Effect of Initial Crown on Shape of Hot Rolled Strip

    Institute of Scientific and Technical Information of China (English)

    HU Yu; GONG Dian-yao; JIANG Zheng-yi; XU Jian-zhong; ZHANG Dian-hua; LIU Xiang-hua

    2009-01-01

    Based on the influence coefficient method, the effect of entry strip crown on the shape of hot rolled strip was analyzed using the software of roll elastic deformation simulation. According to the practical condition of a domestic hot roiled strip plant, the unit strip crown change from the first stand to the last stand was calculated when the entry crown of hot strip varies. The calculated result shows that the entry strip crown does not significantly affect the target strip crown at the exit of the last finishing stand in respect to a fixed strip shape control reference (such as bending force). The calculation was analyzed, and the research is helpful in modeling strip shape setup and shape control.

  6. Dynamic emergence of the mesenchymal CD44(pos)CD24(neg/low) phenotype in HER2-gene amplified breast cancer cells with de novo resistance to trastuzumab (Herceptin).

    Science.gov (United States)

    Oliveras-Ferraros, Cristina; Vazquez-Martin, Alejandro; Martin-Castillo, Begoña; Cufí, Silvia; Del Barco, Sonia; Lopez-Bonet, Eugeni; Brunet, Joan; Menendez, Javier A

    2010-06-18

    Evidence is mounting that the occurrence of the CD44(pos)/CD24(neg/low) cell population, which contains potential breast cancer (BC) stem cells, could explain BC clinical resistance to HER2-targeted therapies. We investigated whether de novo refractoriness to the anti-HER2 monoclonal antibody trastuzumab (Tzb; Herceptin) may relate to the dynamic regulation of the mesenchymal CD44(pos)/CD24(neg/low) phenotype in HER2-positive BC. We observed that the subpopulation of Tzb-refractory JIMT-1 BC cells exhibiting CD44(pos)/CD24(neg/low)-surface markers switched with time. Low-passage JIMT-1 cell cultures were found to spontaneously contain approximately 10% of cells bearing the CD44(pos)/CD24(neg/low) immunophenotype. Late-passage (>60) JIMT-1 cultures accumulated approximately 80% of CD44(pos)/CD24(neg/low) cells and closely resembled the CD44(pos)/CD24(neg/low)-enriched ( approximately 85%) cell population constitutively occurring in HER2-negative MDA-MB-231 mesenchymal BC cells. Dynamic expression of mesenchymal markers was not limited to CD44/CD24 because high-passages of JIMT-1 cells exhibited also reduced expression of the HER2 protein and over-secretion of pro-invasive/metastatic chemokines and metalloproteases. Accordingly, late-passage JIMT-1 cells displayed an exacerbated migratogenic phenotype in plastic, collagen, and fibronectin substrates. Intrinsic genetic plasticity to efficiently drive the emergence of the CD44(pos)/CD24(neg/low) mesenchymal phenotype may account for de novo resistance to HER2 targeting therapies in basal-like BC carrying HER2 gene amplification.

  7. A Perspective on Reagent Diversity and Non-covalent Binding of Reactive Carbonyl Species (RCS and Effector Reagents in Non-enzymatic Glycation (NEG: Mechanistic Considerations and Implications for Future Research

    Directory of Open Access Journals (Sweden)

    Kenneth J. Rodnick

    2017-06-01

    Full Text Available This perspective focuses on illustrating the underappreciated connections between reactive carbonyl species (RCS, initial binding in the nonenzymatic glycation (NEG process, and nonenzymatic covalent protein modification (here termed NECPM. While glucose is the central species involved in NEG, recent studies indicate that the initially-bound glucose species in the NEG of human hemoglobin (HbA and human serum albumin (HSA are non-RCS ring-closed isomers. The ring-opened glucose, an RCS structure that reacts in the NEG process, is most likely generated from previously-bound ring-closed isomers undergoing concerted acid/base reactions while bound to protein. The generation of the glucose RCS can involve concomitantly-bound physiological species (e.g., inorganic phosphate, water, etc.; here termed effector reagents. Extant NEG schemes do not account for these recent findings. In addition, effector reagent reactions with glucose in the serum and erythrocyte cytosol can generate RCS (e.g., glyoxal, glyceraldehyde, etc.. Recent research has shown that these RCS covalently modify proteins in vivo via NECPM mechanisms. A general scheme that reflects both the reagent and mechanistic diversity that can lead to NEG and NECPM is presented here. A perspective that accounts for the relationships between RCS, NEG, and NECPM can facilitate the understanding of site selectivity, may help explain overall glycation rates, and may have implications for the clinical assessment/control of diabetes mellitus. In view of this perspective, concentrations of ribose, fructose, Pi, bicarbonate, counter ions, and the resulting RCS generated within intracellular and extracellular compartments may be of importance and of clinical relevance. Future research is also proposed.

  8. Detection of pump degradation

    Energy Technology Data Exchange (ETDEWEB)

    Greene, R.H.; Casada, D.A.; Ayers, C.W. [and others

    1995-08-01

    This Phase II Nuclear Plant Aging Research study examines the methods of detecting pump degradation that are currently employed in domestic and overseas nuclear facilities. This report evaluates the criteria mandated by required pump testing at U.S. nuclear power plants and compares them to those features characteristic of state-of-the-art diagnostic programs and practices currently implemented by other major industries. Since the working condition of the pump driver is crucial to pump operability, a brief review of new applications of motor diagnostics is provided that highlights recent developments in this technology. The routine collection and analysis of spectral data is superior to all other technologies in its ability to accurately detect numerous types and causes of pump degradation. Existing ASME Code testing criteria do not require the evaluation of pump vibration spectra but instead overall vibration amplitude. The mechanical information discernible from vibration amplitude analysis is limited, and several cases of pump failure were not detected in their early stages by vibration monitoring. Since spectral analysis can provide a wealth of pertinent information concerning the mechanical condition of rotating machinery, its incorporation into ASME testing criteria could merit a relaxation in the monthly-to-quarterly testing schedules that seek to verify and assure pump operability. Pump drivers are not included in the current battery of testing. Operational problems thought to be caused by pump degradation were found to be the result of motor degradation. Recent advances in nonintrusive monitoring techniques have made motor diagnostics a viable technology for assessing motor operability. Motor current/power analysis can detect rotor bar degradation and ascertain ranges of hydraulically unstable operation for a particular pump and motor set. The concept of using motor current or power fluctuations as an indicator of pump hydraulic load stability is presented.

  9. Ram pressure stripping of tilted galaxies

    CERN Document Server

    Jachym, P; Palous, J; Combes, F

    2009-01-01

    Ram pressure stripping of galaxies in clusters can yield gas deficient disks. Previous numerical simulations based on various approaches suggested that, except for near edge-on disk orientations, the amount of stripping depends very little on the inclination angle. Following our previous study of face-on stripping, we extend the set of parameters with the disk tilt angle and explore in detail the effects of the ram pressure on the interstellar content (ISM) of tilted galaxies that orbit in various environments of clusters, with compact or extended distributions of the intra-cluster medium (ICM). We further study how results of numerical simulations could be estimated analytically. A grid of numerical simulations with varying parameters is produced using the tree/SPH code GADGET with a modified method for calculating the ISM-ICM interaction. These SPH calculations extend the set of existing results obtained from different codes using various numerical techniques. The simulations confirm the general trend of le...

  10. Asset Stripping in a Mature Market Economy

    DEFF Research Database (Denmark)

    Klarskov Jeppesen, Kim; Møller, Ulrik Gorm

    2011-01-01

    indicates that asset stripping may take place in mature market economies to the extent that perpetrators are able to circumvent the corporate governance system by giving lawyers, public accountants and banks incentives to act less critically towards dubious business transactions. Research limitations......Purpose – The purpose of this paper is to document a Danish fraud scheme, in which a large number of limited companies were stripped of their assets leaving them with nothing but tax debt, eventually causing the Danish Tax and Customs Administration to lose large sums. Furthermore, the purpose...... is to analyse why the asset-stripping schemes occurred in a mature market economy with a strong corporate governance system and a low level of corruption. Design/methodology/approach – The research is conducted as a longitudinal single case study based on documentary research. Findings – The Danish case...

  11. Detection of pump degradation

    Energy Technology Data Exchange (ETDEWEB)

    Casada, D. [Oak Ridge National Lab., TN (United States)

    1995-04-01

    There are a variety of stressors that can affect the operation of centrifugal pumps. Although these general stressors are active in essentially all centrifugal pumps, the stressor level and the extent of wear and degradation can vary greatly. Parameters that affect the extent of stressor activity are manifold. In order to assure the long-term operational readiness of a pump, it is important to both understand the nature and magnitude of the specific degradation mechanisms and to monitor the performance of the pump. The most commonly applied method of monitoring the condition of not only pumps, but rotating machinery in general, is vibration analysis. Periodic or continuous special vibration analysis is a cornerstone of most pump monitoring programs. In the nuclear industry, non-spectral vibration monitoring of safety-related pumps is performed in accordance with the ASME code. Pump head and flow rate are also monitored, per code requirements. Although vibration analysis has dominated the condition monitoring field for many years, there are other measures that have been historically used to help understand pump condition; advances in historically applied technologies and developing technologies offer improved monitoring capabilities. The capabilities of several technologies (including vibration analysis, dynamic pressure analysis, and motor power analysis) to detect the presence and magnitude of both stressors and resultant degradation are discussed.

  12. Optically pumped atoms

    CERN Document Server

    Happer, William; Walker, Thad

    2010-01-01

    Covering the most important knowledge on optical pumping of atoms, this ready reference is backed by numerous examples of modelling computation for optical pumped systems. The authors show for the first time that modern scientific computing software makes it practical to analyze the full, multilevel system of optically pumped atoms. To make the discussion less abstract, the authors have illustrated key points with sections of MATLAB codes. To make most effective use of contemporary mathematical software, it is especially useful to analyze optical pumping situations in the Liouville spa

  13. Champagne Heat Pump

    Science.gov (United States)

    Jones, Jack A.

    2004-01-01

    The term champagne heat pump denotes a developmental heat pump that exploits a cycle of absorption and desorption of carbon dioxide in an alcohol or other organic liquid. Whereas most heat pumps in common use in the United States are energized by mechanical compression, the champagne heat pump is energized by heating. The concept of heat pumps based on other absorption cycles energized by heat has been understood for years, but some of these heat pumps are outlawed in many areas because of the potential hazards posed by leakage of working fluids. For example, in the case of the water/ammonia cycle, there are potential hazards of toxicity and flammability. The organic-liquid/carbon dioxide absorption/desorption cycle of the champagne heat pump is similar to the water/ammonia cycle, but carbon dioxide is nontoxic and environmentally benign, and one can choose an alcohol or other organic liquid that is also relatively nontoxic and environmentally benign. Two candidate nonalcohol organic liquids are isobutyl acetate and amyl acetate. Although alcohols and many other organic liquids are flammable, they present little or no flammability hazard in the champagne heat pump because only the nonflammable carbon dioxide component of the refrigerant mixture is circulated to the evaporator and condenser heat exchangers, which are the only components of the heat pump in direct contact with air in habitable spaces.

  14. Resonance wave pumping: wave mass transport pumping

    Science.gov (United States)

    Carmigniani, Remi; Violeau, Damien; Gharib, Morteza

    2016-11-01

    It has been previously reported that pinching at intrinsic resonance frequencies a valveless pump (or Liebau pump) results in a strong pulsating flow. A free-surface version of the Liebau pump is presented. The experiment consists of a closed tank with a submerged plate separating the water into a free-surface and a recirculation section connected through two openings at each end of the tank. A paddle is placed at an off-centre position at the free-surface and controlled in a heaving motion with different frequencies and amplitudes. Near certain frequencies identified as resonance frequencies through a linear potential theory analysis, the system behaves like a pump. Particle Image Velocimetry (PIV) is performed in the near free surface region and compared with simulations using Volume of Fluid (VOF) method. The mean eulerian mass flux field (ρ) is extracted. It is observed that the flow is located in the vicinity of the surface layer suggesting Stokes Drift (or Wave Mass Transport) is the source of the pumping. A model is developped to extend the linear potential theory to the second order to take into account these observations. The authors would like to acknowledge the Gordon and Betty Moore Foundation for their generous support.

  15. Rapid diagnosis of meningitis using reagent strips

    Directory of Open Access Journals (Sweden)

    Parmar Ramesh

    2004-02-01

    Full Text Available OBJECTIVES: Identification of causative agent with estimation of cerebrospinal fluid (CSF glucose, protein, cells is necessary for accurate diagnosis of meningitis. Unfortunately, even these facilities are not available in many areas. Reagent strips that measure glucose and protein in blood and urine can serve this task but have been used with varying results in the past. This study was carried out to evaluate the utility and efficacy of Combur 10 strips in the diagnosis of meningitis. DESIGN, SETTINGS AND METHODS: A prospective clinical single blinded study of 63 children suspected to have meningitis undergoing CSF analysis. Each CSF sample was divided in to two and was utilised for reagent strip analysis in addition to standard laboratory evaluation and a correlation analysis were made. Statistical Method used: Results were analysed using standard statistical tests. Accuracy of the reagent strips as a screening tool was established using Godyn′s test. RESULTS: The sensitivity, specificity of the reagent strips for the diagnosis of meningitis was 97.14%, 96.42%. The sensitivity, specificity for tuberculous meningitis and bacterial meningitis were 100%, and 96.55%. That for the aseptic meningitis was 70% and 96.55%. Accuracy for the diagnosis of meningitis as a whole, bacterial meningitis, tuberculous meningitis, and aseptic meningitis were 96.78%, 98.2%, 98.27% and 83.0% respectively. CONCLUSION: Combur10 strips thus can be used for the rapid CSF analysis and screening with good accuracy. In situations where facilities of routine laboratory testing are not available this can be of an immense help.

  16. Lubrication in strip cold rolling process

    Institute of Scientific and Technical Information of China (English)

    Jianlin Sun; Yonglin Kang; Tianguo Xiao; Jianze Wang

    2004-01-01

    A lubrication model was developed for explaining how to form an oil film in the deformation zone, predicting the film thickness and determining the characteristics of lubrication in the strip rolling process, combined with the knowledge of hydrodythicknesses in the strip cold rolling. Results from the experiment and calculation show that the oil film forming in hydrodynamic lubrication is up to the bit angle and a higher rolling speed or a higher rolling oil viscosity. The mechanism of mechanical entrainment always affects the film thickness that increases with the rolling oil viscosity increasing or the reduction rate decreasing in rolling.

  17. Potential profile in a conducting polymer strip

    DEFF Research Database (Denmark)

    Bay, Lasse; West, Keld; Vlachopoulos, Nikolaos

    2002-01-01

    and complicate measurements on free-standing films. A model of the potential profile in a free-standing strip is derived. It is found that the active length (the length with a given potential change) of the polymer will scale as square root (d sigma /i/sub d/). (d is the thickness, sigma the conductivity...... of the film, and i/sub d/ the diffusion limited current density for oxygen reduction). The active length is typically of the order of millimeters. The model is compared with measurements on a strip of polypyrrole doped with dodecylbenzene sulfonate...

  18. Validation of the Hot Strip Mill Model

    Energy Technology Data Exchange (ETDEWEB)

    Richard Shulkosky; David Rosberg; Jerrud Chapman

    2005-03-30

    The Hot Strip Mill Model (HSMM) is an off-line, PC based software originally developed by the University of British Columbia (UBC) and the National Institute of Standards and Technology (NIST) under the AISI/DOE Advanced Process Control Program. The HSMM was developed to predict the temperatures, deformations, microstructure evolution and mechanical properties of steel strip or plate rolled in a hot mill. INTEG process group inc. undertook the current task of enhancing and validating the technology. With the support of 5 North American steel producers, INTEG process group tested and validated the model using actual operating data from the steel plants and enhanced the model to improve prediction results.

  19. Multi-twist optical Mobius strips

    CERN Document Server

    Freund, Isaac

    2009-01-01

    Circularly polarized Gauss-Laguerre GL(0,0) and GL(0,1) laser beams that cross at their waists at a small angle are shown to generate a quasi-paraxial field that contains an axial line of circular polarization, a C line, surrounded by polarization ellipses whose major and minor axes generate multi-twist Mobius strips with twist numbers that increase with distance from the C point. These Mobius strips are interpreted in terms of Berry's phase for parallel transport of the ellipse axes around the C point.

  20. Wokker. Notes on a Surrealist comic strip

    Directory of Open Access Journals (Sweden)

    Roger Sabin

    2012-05-01

    Full Text Available This essay explores the creation and development of a British comic strip, Wokker (1971-1999, and its connections with the surrealist movement. Although the strip is remarkable for its content and formalist properties, it remains obscure both because of its publishing circumstances, and because it does not fit easily into a history of comics. Rather it can be argued that its conceptual roots can be traced to the artistic ferment that happened in Paris in the 1920s (with Breton as a key reference point, and that it represents a very English, and late-flowering, example of the surrealist idea.

  1. Stage- vs. Channel-strip Metaphor

    DEFF Research Database (Denmark)

    Gelineck, Steven; Korsgaard, Dannie Michael; Büchert, Morten

    2015-01-01

    This study compares the stage metaphor and the channel strip metaphor in terms of performance. Traditionally, music mixing consoles employ a channels strip control metaphor for adjusting parameters such as volume and panning of each track. An alternative control metaphor, the so-called stage...... metaphor lets the user adjust volume and panning by positioning tracks relative to a virtual listening position. In this study test participants are given the task to adjust volume and panning of one channel (in mixes consisting of three channels) in order to replicate a series of simple pre-rendered mixes...

  2. Demanding pump power; Krevende pumpekraft

    Energy Technology Data Exchange (ETDEWEB)

    Lie, Oeyvind

    2011-07-01

    The potential for pump power in Norway is huge, but it is difficult to exploit it. Norway has some pumping plants, but these are built for seasonal pumping (pumping up to the magazine in the summer, and production in the winter). Pump power plants for short periods do not exist in Norway. (AG)

  3. Processo de inclusão digital como indutor de estratégia para a sustentabilidade dos negócios

    Directory of Open Access Journals (Sweden)

    Silvia Gattai

    2007-06-01

    Full Text Available As estratégias empresariais têm como principal função garantir a sustentabilidade das organizações, o que depende, entre outros fatores, a médio e longo prazos, da existência de mercados que sejam capazes economicamente de absorver seus produtos. Por outro lado, a concentração de riqueza em pequenos grupos econômicos e o aumento da pobreza em muitos países geram riscos para a perpetuidade dos negócios. As empresas, nesse contexto, necessitam de estratégias que considerem o desenvolvimento estrutural dos países onde atuam, e essa compreensão passa pelo entendimento de sua participação na governança das cidades nas quais possuem suas unidades de negócios, condição fundamental nesse processo. Tal visão é necessária para o desenvolvimento do meio no qual a empresa se insere e, conseqüentemente, à sustentabilidade do negócio. O objetivo deste artigo é buscar compreender o papel de processo de desenvolvimento social, promovido pela empresa, como indutor de estratégias empresariais sustentáveis. Nesse sentido, o artigo aborda os conceitos de prospecção de cenários, ações estratégicas, desenvolvimento empresarial e a agregação de valor social ao ambiente no qual as organizações estão inseridas. A título de exemplificação, relata projeto de inclusão digital envolvendo cadeia de distribuição de empresa cimenteira brasileira de grande porte e o analisa à luz dos conceitos acima referenciados.

  4. Changes in natural Foxp3(+Treg but not mucosally-imprinted CD62L(negCD38(+Foxp3(+Treg in the circulation of celiac disease patients.

    Directory of Open Access Journals (Sweden)

    Marieke A van Leeuwen

    Full Text Available BACKGROUND: Celiac disease (CD is an intestinal inflammation driven by gluten-reactive CD4(+ T cells. Due to lack of selective markers it has not been determined whether defects in inducible regulatory T cell (Treg differentiation are associated with CD. This is of importance as changes in numbers of induced Treg could be indicative of defects in mucosal tolerance development in CD. Recently, we have shown that, after encounter of retinoic acid during differentiation, circulating gut-imprinted T cells express CD62L(negCD38(+. Using this new phenotype, we now determined whether alterations occur in the frequency of natural CD62L(+Foxp3(+ Treg or mucosally-imprinted CD62L(negCD38(+Foxp3(+ Treg in peripheral blood of CD patients. In particular, we compared pediatric CD, aiming to select for disease at onset, with adult CD. METHODS: Cell surface markers, intracellular Foxp3 and Helios were determined by flow cytometry. Foxp3 expression was also detected by immunohistochemistry in duodenal tissue of CD patients. RESULTS: In children, the percentages of peripheral blood CD4(+Foxp3(+ Treg were comparable between CD patients and healthy age-matched controls. Differentiation between natural and mucosally-imprinted Treg on the basis of CD62L and CD38 did not uncover differences in Foxp3. In adult patients on gluten-free diet and in refractory CD increased percentages of circulating natural CD62L(+Foxp3(+ Treg, but normal mucosally-imprinted CD62L(negCD38(+Foxp3(+ Treg frequencies were observed. CONCLUSIONS: Our data exclude that significant numeric deficiency of mucosally-imprinted or natural Foxp3(+ Treg explains exuberant effector responses in CD. Changes in natural Foxp3(+ Treg occur in a subset of adult patients on a gluten-free diet and in refractory CD patients.

  5. Pump element for a tube pump

    DEFF Research Database (Denmark)

    2011-01-01

    relative to the rod element so as to allow for a fluid flow in the tube through the first valve member, along the rod element, and through the second valve member. The tube comprises an at least partly flexible tube portion between the valve members such that a repeated deformation of the flexible tube...... portion acts to alternately close and open the valve members thereby generating a fluid flow through the tube. The invention further relates to a pump element comprising at least two non-return valve members connected by a rod element, and for insertion in an at least partly flexible tube in such tube...... pump as mentioned above, thereby acting to generate a fluid flow through the tube upon repeated deformation of the tube between the two valve members. The pump element may comprise a connecting part for coupling to another tube and may comprise a sealing part establishing a fluid tight connection...

  6. Reflexão sobre a missão desafiadora do constructo marca-país na área de negócios internacionais

    OpenAIRE

    Fabiana Gondim Mariutti

    2015-01-01

    A importância de uma marca-país promovida estrategicamente é um dos propósitos fundamentais em negócios internacionais. Cada nação tenta transmitir seus atributos internacionalmente - não apenas seus produtos e serviços, mas também a sua imagem geral. Além disso, pesquisas sobre o construto de marca-país estão sendo realizadas continuamente em institutos governamentais e ambientes acadêmicos e corporativos. As nações precisam se promover estrategicamente se desejam serem percebidas. Baseada n...

  7. Uma investigação sobre os tipos de confiança e seu desenvolvimento em negócios “business to business”

    OpenAIRE

    2007-01-01

    A confiança tem se mostrado muito importante nas relações entre os canais de negócios business-to-business. Quando presente, a confiança favorece relacionamentos de longo prazo, reduz riscos e encoraja maiores investimentos entre as partes. A confiança é um conceito extremamente complexo e muda de faceta de acordo com a evolução do relacionamento. Entender a complexidade deste conceito bem como a forma como ela se desenvolve é de fundamental importância para a definição das estratégias de mar...

  8. Gestão de continuidade de negócios aplicada no ensino presencial mediado por recursos tecnológicos.

    OpenAIRE

    Diana Maria da Câmara Gorayeb

    2012-01-01

    Este trabalho propõe diretrizes de Gestão de Continuidade de Negócios (GCN) para a tecnologia de Ensino Presencial Mediado por Recursos Tecnológicos (EPMRT), que conta, para a realização de suas atividades acadêmicas, com um sistema complexo para transmissão de aulas e exige um grande esforço para o controle das suas operações e das respostas coordenadas diante de erros, falhas e defeitos, ou quaisquer incidentes que resultem na interrupção das suas atividades. A manutenção deste ambiente tec...

  9. Gerenciamento de projetos em negócios baseados em projetos: uma proposta integrada das dimensões operacional, organizacional e estratégica

    OpenAIRE

    Jefferson Leandro Anselmo

    2009-01-01

    A emergência do gerenciamento de projetos é uma resposta às exigências impostas pelo ambiente empresarial atual. Além de instrumento operacional para a adaptação e evolução organizacional, o gerenciamento de projetos exerce importante papel estratégico, principalmente em empresas cujo negócio tem por base a comercialização de projetos. Os modelos e a literatura sobre as especificidades do gerenciamento de projeto, nesse contexto, são, entretanto, relativamente recentes e pouco extensos. Este ...

  10. Indagine sullo stato sierologico per epatite B e C negli operatori ecologici della cittá di Messina

    Directory of Open Access Journals (Sweden)

    R. Squeri

    2003-05-01

    Full Text Available

    La resistenza del virus dell’epatite B nell’ambiente esterno, rende alcune categorie di lavoratori, fra cui gli operatori ecologici, particolarmente a rischio di venire a contatto con il virus, da qui l’importanza della prevenzione, soprattutto tramite la vaccinazione, in ambienti non sanitari nei quali la cultura rischio biologico è spesso poco valida.

    Nel periodo compreso tra marzo e maggio 2003, abbiamo condotto un’indagine volta a valutare il profilo sierologico riguardo i virus dell’epatite B e C in questa categoria di lavoratori. In seguito abbiamo consultato gli archivi cartacei dell’Ufficio Vaccinazioni dell’AUSL 5, prendendo in considerazione la percentuale di soggetti che si sono sottoposti alla vaccinazione contro l’epatite B, il numero di dosi di vaccino praticate e l’anno della vaccinazione. L’indagine ha coinvolto un campione di 327 operatori ecologici (OE di età compresa tra 24 e 65 anni di cui 288 addetti alle mansioni di spazzamento e raccolta, 26 ad inceneritori, e 13 alle discariche. I dati sierologici hanno evidenziato che degli OE, 190 (58,81% sono risultati negativi per tutti i markers dell’epatite B e C, 58 (18,12% positivi per HbsAb, 31 (9,48% per HbsAb e HbcAb, 13 (3,97% per HbsAg HbcAb e HBeAb, 24 (7,5% per HbsAb, HbcAb e HbeAb, 7 (2,18% per HbcAb e HbeAb, 4 (0,94% per HbcAb ed infine 8 (2,44% per HCV Ab. La consultazione dei registri vaccinazione ha evidenziato che solo il 40,97% degli operatori aveva effettuato, negli anni 1994 - 2002, la vaccinazione contro l’epatite B di questi, l’11,94% ha ricevuto solo una dose, il 14,93% 2 dosi, mentre il 73,13% 3 dosi di vaccino. In quest’ultimi il 52,04% non ha evidenziato la sieroconversione per l’avvenuta vaccinazione. Sulla base dei risultati ottenuti sono stati organizzati incontri per sensibilizzare gli operatori ecologici alla pratica vaccinale contro l’epatite B estendendo l’iniziativa ai datori di lavoro.

  11. A Shocking New Pump

    Science.gov (United States)

    2000-01-01

    Hydro Dynamics, Inc. received a technical helping hand from NASA that made their Hydrosonic Pump (HPump) a reality. Marshall engineers resolved a bearing problem in the rotor of the pump and recommended new bearings, housings and mounting hardware as a solution. The resulting HPump is able to heat liquids with greater energy efficiency using shock waves to generate heat.

  12. Water Treatment Technology - Pumps.

    Science.gov (United States)

    Ross-Harrington, Melinda; Kincaid, G. David

    One of twelve water treatment technology units, this student manual on pumps provides instructional materials for three competencies. (The twelve units are designed for a continuing education training course for public water supply operators.) The competencies focus on the following areas: types of pumps in plant and distribution systems, pump…

  13. Comparative evaluation of scanned stripping techniques: SSCP vs. SSV

    NARCIS (Netherlands)

    Town, R.M.; Leeuwen, van H.P.

    2006-01-01

    The characteristic features of scanned deposition potential curves constructed from stripping chronopotentiometry (SSCP) and various modes of stripping voltammetry (SSV) are critically evaluated. The strengths and weaknesses of each method for identification of metal ion speciation features and susc

  14. Topics in Chemical Instrumentation: CII. Automated Anodic Stripping Voltammetry.

    Science.gov (United States)

    Stock, John T.; Ewing, Galen W., Ed.

    1980-01-01

    Presents details of anodic stripping analysis (ASV) in college chemistry laboratory experiments. Provides block diagrams of the analyzer system, circuitry and power supplies of the automated stripping analyzer, and instructions for implementing microcomputer control of the ASV. (CS)

  15. Review of magnetohydrodynamic pump applications

    National Research Council Canada - National Science Library

    Al-Habahbeh, O.M; Al-Saqqa, M; Safi, M; Abo Khater, T

    2016-01-01

    Magneto-hydrodynamic (MHD) principle is an important interdisciplinary field. One of the most important applications of this effect is pumping of materials that are hard to pump using conventional pumps...

  16. Propulsion by Helical Strips in Circular Channels

    Science.gov (United States)

    Yesilyurt, Serhat; Demir, Ebru

    2016-11-01

    Progress in manufacturing techniques avails the production of artificial micro swimmers (AMS) in various shapes and sizes. There are numerous studies on the generation of efficient locomotion by means of helical tails with circular cross-sections. This work focuses on locomotion with helical strips in circular channels. A CFD model is used to analyze the effects of geometric parameters and the radius of the channel on swimming velocity of infinite helical-strips in circular channels. Results show that there is an optimum wavelength that depends on thickness to channel radius ratio, suggesting that these parameters need to be optimized simultaneously. With constant torque, thinner strips swim faster, whereas under constant angular velocity application, thicker strips (in radial direction) prevail. As width approaches the wavelength, velocity decreases under both conditions, unless a magnetically coated tail is simulated, for which width has an optimum value. Increasing channel radius to helix amplitude ratio increases the velocity up to a maximum and after a slight drop, saturation occurs as bulk swimming conditions are approached.

  17. Nanoscale Test Strips for Multiplexed Blood Analysis

    Science.gov (United States)

    Chan, Eugene

    2015-01-01

    A critical component of the DNA Medicine Institute's Reusable Handheld Electrolyte and Lab Technology for Humans (rHEALTH) sensor are nanoscale test strips, or nanostrips, that enable multiplexed blood analysis. Nanostrips are conceptually similar to the standard urinalysis test strip, but the strips are shrunk down a billionfold to the microscale. Each nanostrip can have several sensor pads that fluoresce in response to different targets in a sample. The strips carry identification tags that permit differentiation of a specific panel from hundreds of other nanostrip panels during a single measurement session. In Phase I of the project, the company fabricated, tested, and demonstrated functional parathyroid hormone and vitamin D nanostrips for bone metabolism, and thrombin aptamer and immunoglobulin G antibody nanostrips. In Phase II, numerous nanostrips were developed to address key space flight-based medical needs: assessment of bone metabolism, immune response, cardiac status, liver metabolism, and lipid profiles. This unique approach holds genuine promise for space-based portable biodiagnostics and for point-of-care (POC) health monitoring and diagnostics here on Earth.

  18. Comic Strips to Accompany Science Museum Exhibits

    Science.gov (United States)

    Chung, Beom Sun; Park, Eun-mi; Kim, Sang-Hee; Cho, Sook-kyoung; Chung, Min Suk

    2016-01-01

    Science museums make the effort to create exhibits with amusing explanations. However, existing explanation signs with lengthy text are not appealing, and as such, visitors do not pay attention to them. In contrast, conspicuous comic strips composed of simple drawings and humors can attract science museum visitors. This study attempted to reveal…

  19. Improved Lower Bound for Online Strip Packing

    NARCIS (Netherlands)

    Harren, Rolf; Kern, Walter

    We study the online strip packing problem and derive an improved lower bound of Ͽ ≥ 2.589... for the competitive ratio of this problem. The construction is based on modified “Brown-Baker-Katseff sequences‿ (Brown et al. in Acta Inform. 18:207–225, 1982) using only two types of rectangles. In

  20. Polymer Inclusion Membranes with Strip Dispersion

    Directory of Open Access Journals (Sweden)

    Yueh-Hsien Li

    2017-06-01

    Full Text Available The present work investigated the permeation of indium ions through a polymer inclusion membrane (PIM, prepared with cellulose triacetate (CTA as the base polymer, tris(2-butoxyethyl phosphate (TBEP as the plasticizer and di-(2-ethylhexylphosphoric acid (D2EHPA as the extractant. With 5 M HCl aqueous solution as the strip solution, we observed an initial indium permeability of 2.4 × 10−4 m/min. However, the permeability decreases with time, dropping to about 3.4 × 10−5 m/min after 200 min of operation. Evidence was obtained showing that hydrolysis of CTA occurred, causing a dramatic decrease in the feed pH (protons transported from strip to feed solutions and a loss of extractant and plasticizer from the membrane, and then leading to the loss of indium permeability. To alleviate the problem of hydrolysis, we proposed an operation scheme called polymer inclusion membranes with strip dispersion: dispersing the strip solution in extractant-containing oil and then bringing the dispersion to contact with the polymer membrane. Since the strong acid was dispersed in oil, the membrane did not directly contact the strong acid at all times, and membrane hydrolysis was thus alleviated and the loss of indium permeability was effectively prevented. With the proposed scheme, a stable indium permeability of 2.5 × 10−4 m/min was obtained during the whole time period of the permeation experiment.

  1. Inadvertent femoral artery "stripping": surgical management.

    Science.gov (United States)

    Liddicoat, J E; Bekassy, S M; Daniell, M B; De Bakey, M E

    1975-02-01

    Following "vein stripping" for varicosities, two patients were referred to our service for evaluation of arterial insufficiency of the lower extremities. Both patients had had surgical interruption of the femoral arterial system which required reconstruction. This paper emphasizes the importance of understanding surgical anatomy and presents the techniques of successful surgical management of both cases.

  2. ME1/1 Cathode Strip Chambers

    CERN Document Server

    Erchov, Yu V; Kamenev, Alexey; Karjavin, Vladimir; Khabarov, Serguei; Moissenz, P V; Moissenz, K P; Movchan, Sergey; Perelygin, Victor; Vassiliev, S E; Zarubin, Anatoli; Tchekhovski, V A

    2008-01-01

    The 76 innermost ME1/1 cathode strip chambers (CSC) of the CMS Experiment were designed and produced in Dubna. The chambers have been installed in the detector and commissioning has been completed. This paper describes the design of the CSCs, their main mechanical parameters and read-out electronics, and the results of tests with cosmic-ray muons.

  3. Cardiac Muscle Studies with Rat Ventricular Strips

    Science.gov (United States)

    Whitten, Bert K.; Faleschini, Richard J.

    1977-01-01

    Details undergraduate physiology laboratory experiments that demonstrate mechanical properties of cardiac muscle, using strips from the ventricle of a rat heart. Includes procedures for obtaining length-tension curves, demonstrating the role of calcium in excitation-contraction coupling, and showing effects of several cardiovascular drugs…

  4. Anodic Stripping Voltammetry: An Instrumental Analysis Experiment.

    Science.gov (United States)

    Wang, Joseph

    1983-01-01

    Describes an experiment designed to acquaint students with the theory and applications of anodic stripping voltammetry (ASV) as well as such ASV problems as contamination associated with trace analysis. The experimental procedure, instrumentation, and materials discussed are designed to minimize cost and keep procedures as simple as possible. (JM)

  5. Hardness of approximation for strip packing

    DEFF Research Database (Denmark)

    Adamaszek, Anna Maria; Kociumaka, Tomasz; Pilipczuk, Marcin

    2017-01-01

    [SODA 2016] have recently proposed a (1.4 + ϵ)-approximation algorithm for this variant, thus showing that strip packing with polynomially bounded data can be approximated better than when exponentially large values are allowed in the input. Their result has subsequently been improved to a (4/3 + ϵ...

  6. Refuges, flower strips, biodiversity and agronomic interest.

    Science.gov (United States)

    Roy, Grégory; Wateau, Karine; Legrand, Mickaël; Oste, Sandrine

    2008-01-01

    Several arthropods are natural predators of pests, and they are able to reduce and control their population development. FREDON Nord Pas-de-Calais (Federation Regionate de Defense contre les Organismes Nuisibles = Regional Federation for Pest Control) has begun for a long time to form farmers to the recognition of beneficial arthropods and to show them their usefulness. These beneficial insects or arachnids are present everywhere, in orchards and even in fields which are areas relatively poor in biodiversity. Adults feed in the flower strips instead larvae and some adults feed on preys such as aphids or caterpillars. Most of the time, beneficial insects can regulate pest but sometimes, in agricultural area, they can't make it early enough and efficiently. Their action begin too late and there biodiversity and number are too low. It's possible to enhance their action by manipulating the ecological infrastructures, like sewing flower strips or installing refuges. Flower strips increase the density of natural enemies and make them be present earlier in the field in order to control pests. Refuges permit beneficial's to spend winter on the spot. So they're able to be active and to grow in number earlier. From 2004 to 2007, on the one hand, FREDON Nord Pas-de-Calais has developed a research program. Its purpose was to inventory practices and also tools and means available and to judge the advisability of using such or such beneficial refuge in orchards. On the second hand, it studied the impact in orchard of refuges on population of beneficial's and the difference there were between manufactured refuges and homemade refuges. Interesting prospects were obtained with some of them. Otherwise, since 2003, FREDON has studied flower strips influence on beneficial population and their impact on pest control. In cabbage fields, results of trials have shown that flower strips lead to a reduction of aphid number under acceptable economic level, up to 50 meters from flower strips

  7. Dual Strip-Excited Dielectric Resonator Antenna with Parasitic Strips for Radiation Pattern Reconfigurability

    Directory of Open Access Journals (Sweden)

    M. Kamran Saleem

    2014-01-01

    Full Text Available A novel pattern reconfigurable antenna concept utilizing rectangular dielectric resonator antenna (DRA placed over dielectric substrate backed by a ground plane is presented. A dual strip excitation scheme is utilized and both excitation strips are connected together by means of a 50 Ω microstrip feed network placed over the substrate. The four vertical metallic parasitic strips are placed at corner of DRA each having a corresponding ground pad to provide a short/open circuit between the parasitic strip and antenna ground plane, through which a shift of 90° in antenna radiation pattern in elevation plane is achieved. A fractional bandwidth of approximately 40% at center frequency of 1.6 GHz is achieved. The DRA peak realized gain in whole frequency band of operation is found to be above 4 dB. The antenna configuration along with simulation and measured results are presented.

  8. Strip reduction testing of lubricants developed during ENFORM project

    DEFF Research Database (Denmark)

    Gazvoda, S.; Andreasen, Jan Lasson; Olsson, David Dam

    Strip reduction testing of lubricants developed during ENFORM project. Experiments were conducted with the strip reduction test [1] in order to classify experimental lubricants, developed during concerned project. One reference lubricant was used during testing.......Strip reduction testing of lubricants developed during ENFORM project. Experiments were conducted with the strip reduction test [1] in order to classify experimental lubricants, developed during concerned project. One reference lubricant was used during testing....

  9. Pumping machinery theory and practice

    CERN Document Server

    Badr, Hassan M

    2014-01-01

    Pumping Machinery Theory and Practice comprehensively covers the theoretical foundation and applications of pumping machinery. Key features: Covers characteristics of centrifugal pumps, axial flow pumps and displacement pumpsConsiders pumping machinery performance and operational-type problemsCovers advanced topics in pumping machinery including multiphase flow principles, and two and three-phase flow pumping systemsCovers different methods of flow rate control and relevance to machine efficiency and energy consumptionCovers different methods of flow rate control and relevance to machine effi

  10. TOMOGRAPHIC MEASUREMENT OF LONGITUDINAL EMITTANCE GROWTH DUE TO STRIPPING FOILS.

    Energy Technology Data Exchange (ETDEWEB)

    MONTAG, C.; AHRENS, L.; THIEBERGER, P.

    2005-05-16

    During beam acceleration in the Brookhaven accelerator complex, heavy ions are stripped of their electrons in several steps. Depending on the properties of the stripping foils, this process results in an increased energy spread and longitudinal emittance growth. A tomographic phase space reconstruction technique has been applied to measure the associated emittance growth for different stripping foil materials.

  11. A Gestão do Negócio Turístico apoiado na capacitação profissional e na qualidade do atendimento ao cliente

    Directory of Open Access Journals (Sweden)

    Liliane Azevedo Santaella

    2013-07-01

    Full Text Available O negócio turístico é um dos maiores geradores de benefícios para o País e para as comunidades locais, como podemos ver por meio da história. Porém, para que o este negócio agregue valor as pessoas, as organizações e as comunidades necessitam alinhar-se às características e necessidades do contexto atual. O século XXI acena para uma sociedade baseada no conhecimento, com pessoas treinadas e capacitadas para tomadas de decisões, isto é, com competências que agreguem valor ao negócio.

  12. Segmento do Turismo de Negócios para as Agências de Viagem: Perfil de Clientes Corporativos de Fortaleza e Região Metropolitana

    Directory of Open Access Journals (Sweden)

    Keila Cristina Nicolau Mota

    2011-09-01

    Full Text Available O turismo de negócios vem se expandindo no mercado, contribuindo para a geração de emprego e renda, movimentando a economia. Com a globalização, os avanços da tecnologia, além das facilidades de transporte e comunicação, o turismo corporativo tem se tornado expressivo e tem exigido uma maior atenção, no sentido de promover um serviço condizente com as necessidades contemporâneas. Os clientes corporativos das agências de viagem apresentam características próprias e exigem profissionais capacitados. O presente artigo objetiva analisar empresas de Fortaleza e Região Metropolitana que são clientes de agências de viagem. Por meio de uma pesquisa de campo que identificou as principais características e tendências do setor nos meses de maio e junho de 2010, relacionando aspectos típicos do turismo de negócios. O mercado de viagens destes clientes tem contribuído para o desenvolvimento do setor, porém carece de agências que trabalhem a gestão de viagens de forma mais especializada.

  13. Contribuição da Abordagem System Dynamics na Compreensão da Competitividade de Clusters de Negócios

    Directory of Open Access Journals (Sweden)

    André Alarcon de Almeida Prado

    2013-12-01

    Full Text Available O presente trabalho teve como objetivo a constituição de um modelamento exploratório da operação de clusters de negócios por meio da abordagem System Dynamics, considerando, como fatores intervenientes do processo, os fundamentos da performance competitiva de clusters, proposto por Zaccarelli, Telles, Siqueira, Boaventura e Donaire (2008. Por meio da estruturação, segundo a metodologia system dynamics, da interação dos efeitos sistêmicos, responsáveis pelo estágio competitivo desses arranjos inter-organizacionais, segundo os autores, foram desenvolvidos diagramas causais para cada fundamento. Como principais resultados, o mapeamento das interações dinâmicas ofereceu uma nova perspectiva teórica e gerencial sobre operação e competitividade de clusters de negócios. DOI:10.5585/riae.v12i4.2011

  14. Indicadores de Sustentabilidade em Simulações de Negócios: uma proposição no contexto do jogo de empresas SEE

    Directory of Open Access Journals (Sweden)

    Paulo da Costa Lopes

    2010-02-01

    Full Text Available O artigo foi desenvolvido com o objetivo de propor a inserção de indicadores de sustentabilidade em simulações de negócios. Para tanto, foi realizada uma pesquisa básica, qualitativa, descritiva, bibliográfica e documental. Foi elaborado um levantamento teórico-metodológico sobre jogos de empresas e sustentabilidade, foi introduzida a Global Reporting Initiative (GRI como promotora de um padrão de comunicação global em ações empresariais sustentáveis, e apresentou-se o jogo de empresas SEE (Simulador de Estratégia Empresarial. Este artigo, entre outros propósitos, intenciona identificar, pela realidade dos relatórios sustentáveis brasileiros, estruturados segundo as diretrizes da GRI, e publicados em 2008, quais os indicadores – EC1, EN3, HR6, LA1, PR5 e SO1 – mais reportados por essas empresas. Esses são os indicadores de sustentabilidade propostos para serem inseridos em uma ambiência de simulações de negócios amparada pelo jogo de empresas SEE.

  15. «A Monstrous Regiment of Women»: nascite mostruose come stigma del dissenso religioso delle donne negli anni delle guerre civili inglesi (1642-1652

    Directory of Open Access Journals (Sweden)

    Luca Baratta

    2016-04-01

    Full Text Available Il presente lavoro prende in esame quattro resoconti di nascite di esseri umani con malformazioni congenite pubblicati a Londra tra il 1642 e 1652. Messi in circolazione dalla stampa nel frastagliato quadro del conflitto tra Carlo I e il Parlamento, e più nello specifico negli anni in cui non si era ancora del tutto spenta la polemica sulla chiesa riformata, i quattro pamphlet sono accomunati dalla medesima lettura della nascita mostruosa, vista come esito di una qualche forma di dissenso religioso da parte delle madri protagoniste. La colpevolizzazione delle donne non era un fenomeno nuovo: già nei decenni precedenti alle guerre civili, le narrazioni di nascite mostruose avevano frequentemente messo in luce negativa le donne, spesso attraverso il sillogismo per cui la nascita di un figlio deforme dichiarava una colpa segreta della genitrice. La novità dei documenti che raccontarono le cosiddette monstrous births negli anni 1642-1652 fu di appuntare il proprio stigma su una colpa materna che non era più di tipo sessuale, o più in generale morale: la propaganda religiosa e politica strumentalizzò i parti di bambini deformi, interpretandoli come punizioni divine per il dissenso religioso manifestato dalle loro madri.

  16. Bird community response to filter strips in Maryland

    Science.gov (United States)

    Blank, P.J.; Dively, G.P.; Gill, D.E.; Rewa, C.A.

    2011-01-01

    Filter strips are strips of herbaceous vegetation planted along agricultural field margins adjacent to streams or wetlands and are designed to intercept sediment, nutrients, and agrichemicals. Roughly 16,000 ha of filter strips have been established in Maryland through the United States Department of Agriculture's Conservation Reserve Enhancement Program. Filter strips often represent the only uncultivated herbaceous areas on farmland in Maryland and therefore may be important habitat for early-successional bird species. Most filter strips in Maryland are planted to either native warm-season grasses or cool-season grasses and range in width from 10.7 m to 91.4 m. From 2004 to 2007 we studied the breeding and wintering bird communities in filter strips adjacent to wooded edges and non-buffered field edges and the effect that grass type and width of filter strips had on bird community composition. We used 5 bird community metrics (total bird density, species richness, scrub-shrub bird density, grassland bird density, and total avian conservation value), species-specific densities, nest densities, and nest survival estimates to assess the habitat value of filter strips for birds. Breeding and wintering bird community metrics were greater in filter strips than in non-buffered field edges but did not differ between cool-season and warm-season grass filter strips. Most breeding bird community metrics were negatively related to the percent cover of orchardgrass (Dactylis glomerata) in ???1 yr. Breeding bird density was greater in narrow (60 m) filter strips. Our results suggest that narrow filter strips adjacent to wooded edges can provide habitat for many bird species but that wide filter strips provide better habitat for grassland birds, particularly obligate grassland species. If bird conservation is an objective, avoid planting orchardgrass in filter strips and reduce or eliminate orchardgrass from filter strips through management practices. Copyright ?? 2011 The

  17. Improving Thin Strip Profile Using Work Roll Cross and Work Roll Shifting Methods in Cold Strip Rolling

    Directory of Open Access Journals (Sweden)

    Hasan Tibar

    2017-01-01

    Full Text Available The optimization of rolling parameters in order to achieve better strip shape and to reduce rolling force is a challenge in rolling practice. In this paper, thin strip asymmetrical rolling of aluminum at various speed ratios under lubricated condition has been investigated at various combinations of work rolls cross (WRC angles and work rolls shifting (WRS values. The effects of strip width, reduction, and rolling speed on strip shape taking WRC and WRS into consideration are discussed. Results show that strip profile improves significantly when the WRC angle is increased from 0° to 1°, with an associated reduction in rolling force. Increasing WRS value from 0 to 8 mm improves the strip profile as well but not as significantly as when WRC angle is increased. No significant improvement was found in strip shape when the strip width was increased. At higher reduction, the strip shape was improved; a decrease in the rolling force was also observed. A higher speed ratio was found to be effective only at a higher WRC angle. The effect of lubrication on the strip profile was significant. Results indicate that an optimum combination of WRC, WRS, reduction, width, and speed ratio under lubricated conditions can ensure an improved exit strip profile, reduce rolling force, and obtain a better quality strip.

  18. Um Sistema Especialista Probabilístico para o Apoio a Análise de Planos de Negócios de Empresas de Base Tecnológica

    Directory of Open Access Journals (Sweden)

    Jordan Pauleski Juliani

    2005-12-01

    Full Text Available Este artigo apresenta uma proposta de desenvolvimento de um sistema especialista probabilístico como forma de apoiar a análise dos planos de negócio de empresas de tecnologia, por parte dos consultores especializados, estruturados para fim de ingresso em análise de planos de negócio, como forma de julgar novos projetos de empresas, gerando como resultado para as incubadoras um alto risco de não apoiar projetos com real potencial de desenvolvimento, desestimulando o empreendedorismo e prejudicando a economia local.

  19. Mecanismos de coordenação em redes de pequenos negócios supermercadistas no estado de São Paulo: formalidade, informalidade e coesão relacional

    OpenAIRE

    Luciano Mitidieri Bento Garcia; Luiz Fernando de Oriani Paulillo

    2014-01-01

    Alguns supermercadistas de pequeno porte têm procurado enfrentar o maior poder de mercado dos grandes grupos do setor mediante ações cooperativas que se desenvolvem nas chamadas centrais de negócio. De acordo com as perspectivas teóricas representadas pelo neoinstitucionalismo e pela abordagem de redes, especialmente quanto à sua perspectiva relacional, as centrais de negócio de pequenos supermercadistas podem ser definidas como redes cooperativas horizontais, cuja eficácia está associada aos...

  20. Modelagem de processos de negócios na implementação de ERPs nacionais em PMEs Business processes modeling in the implementation of national ERPs within SMEs

    OpenAIRE

    Fernanda Pereira Carneiro da Silva; Néocles Alves Pereira

    2006-01-01

    Este artigo apresenta evidências encontradas em uma pesquisa que teve como objetivo investigar a contribuição do uso da Modelagem dos Processos dos Negócios (MPN) na implementação do Enterprise Resource Planning (ERP) em pequenas e médias empresas (PMEs). Foi observado, nos principais fornecedores nacionais deste sistema, o uso da MPN, verificando sua influência na integração dos processos internos dos negócios de seus clientes. Para esta investigação buscaram-se as informações nos fornecedor...

  1. Do mainframe à nuvem: inovações, estrutura industrial e modelos de negócios nas tecnologias da informação e da comunicação

    OpenAIRE

    Paulo Bastos Tigre; Vitor Branco Noronha

    2013-01-01

    Inovações radicais nas tecnologias da informação e da comunicação (TIC) abrem oportunidades para o desenvolvimento de novos modelos de negócios que, quando bem-sucedidos, acabam por alterar a própria estrutura da indústria global. A partir da revisão de mudanças estruturais ocorridas nas TIC nas últimas cinco décadas, neste artigo analisam-se a relação entre novas tecnologias, o surgimento de empresas consideradas paradigmas e seus respectivos modelos de negócios visando contribuir para o pro...

  2. Modelo conceitual de decisões no estágio de criação de um negócio: base para construção de um simulador para jogos de empresas

    OpenAIRE

    2009-01-01

    O estudo teve como objetivo desenvolver um modelo conceitual para jogo de empresas que reúne as principais decisões de um empreendedor no estágio de criação de um negócio. As decisões, identificadas na literatura de empreendedorismo que foca o processo de criação de negócios, foram modeladas pelo método do diagrama de influências e confirmadas com especialistas norte-americanos e brasileiros no tema. O modelo conceitual resultante, aqui proposto para a criação de um simulador, foi comparado a...

  3. Shape Setup System for 1700 Hot Strip Mill

    Institute of Scientific and Technical Information of China (English)

    GUO Zhong-feng; XU Jian-zhong; LI Chang-sheng; LIU Xiang-hua

    2007-01-01

    Shape setup (SSU) system is the core technology for hot strip mill (HSM). A precise SSU system was used to improve the strip quality for HSM. The function of SSU, setup, and feedback was introduced. The main mathematical models of roll gap profile and longitudinal strain difference are set up. Strip profile allocation strategy was researched according to the SSU system of a domestic 1 700 mm HSM. The SSU system was put into practical use and the measurement results showed that strip flatness variation and strip profile variation could be controlled in target scope.

  4. The Formation and Evolution of Stripped Dark Matter Halos

    Science.gov (United States)

    Zhu, Jessica; Tuan, Austin Zong; Lee, Christoph; Primack, Joel R.

    2016-01-01

    We implement a model to describe the density profiles of stripped dark matter halos. Our model generalizes the Navarro-Frenk-White (NFW) distribution to allow for more flexibility in the slope of the outer halo. We find that the density distributions of stripped halos tend to have outer slopes steeper than assumed by the NFW distribution. We also examine the relationship between severity of stripping and halo shape, spin parameter and concentration, and find that highly stripped halos are more spheroidal, have lower spin parameters, and have higher concentrations compared to less stripped halos.

  5. Nuclear-pumped lasers

    CERN Document Server

    Prelas, Mark

    2016-01-01

    This book focuses on Nuclear-Pumped Laser (NPL) technology and provides the reader with a fundamental understanding of NPLs, a review of research in the field, and exploration of large scale NPL system design and applications. Early chapters look at the fundamental properties of lasers, nuclear-pumping and nuclear reactions that may be used as drivers for nuclear-pumped lasers. The book goes on to explore the efficient transport of energy from the ionizing radiation to the laser medium and then the operational characteristics of existing nuclear-pumped lasers. Models based on Mathematica, explanations and a tutorial all assist the reader’s understanding of this technology. Later chapters consider the integration of the various systems involved in NPLs and the ways in which they can be used, including beyond the military agenda. As readers will discover, there are significant humanitarian applications for high energy/power lasers, such as deflecting asteroids, space propulsion, power transmission and mining....

  6. Absorption heat pump system

    Science.gov (United States)

    Grossman, G.

    1982-06-16

    The efficiency of an absorption heat pump system is improved by conducting liquid from a second stage evaporator thereof to an auxiliary heat exchanger positioned downstream of a primary heat exchanger in the desorber of the system.

  7. High Voltage Charge Pump

    KAUST Repository

    Emira, Ahmed A.

    2014-10-09

    Various embodiments of a high voltage charge pump are described. One embodiment is a charge pump circuit that comprises a plurality of switching stages each including a clock input, a clock input inverse, a clock output, and a clock output inverse. The circuit further comprises a plurality of pumping capacitors, wherein one or more pumping capacitors are coupled to a corresponding switching stage. The circuit also comprises a maximum selection circuit coupled to a last switching stage among the plurality of switching stages, the maximum selection circuit configured to filter noise on the output clock and the output clock inverse of the last switching stage, the maximum selection circuit further configured to generate a DC output voltage based on the output clock and the output clock inverse of the last switching stage.

  8. Regenerative Hydride Heat Pump

    Science.gov (United States)

    Jones, Jack A.

    1992-01-01

    Hydride heat pump features regenerative heating and single circulation loop. Counterflow heat exchangers accommodate different temperatures of FeTi and LaNi4.7Al0.3 subloops. Heating scheme increases efficiency.

  9. Underground pumped hydroelectric storage

    Science.gov (United States)

    Allen, R. D.; Doherty, T. J.; Kannberg, L. D.

    1984-07-01

    Underground pumped hydroelectric energy storage was conceived as a modification of surface pumped storage to eliminate dependence upon fortuitous topography, provide higher hydraulic heads, and reduce environmental concerns. A UPHS plant offers substantial savings in investment cost over coal-fired cycling plants and savings in system production costs over gas turbines. Potential location near load centers lowers transmission costs and line losses. Environmental impact is less than that for a coal-fired cycling plant. The inherent benefits include those of all pumped storage (i.e., rapid load response, emergency capacity, improvement in efficiency as pumps improve, and capacity for voltage regulation). A UPHS plant would be powered by either a coal-fired or nuclear baseload plant. The economic capacity of a UPHS plant would be in the range of 1000 to 3000 MW. This storage level is compatible with the load-velocity requirements of a greater metropolitan area with population of 1 million or more.

  10. Chiral brownian heat pump.

    Science.gov (United States)

    van den Broek, M; Van den Broeck, C

    2008-04-04

    We present the exact analysis of a chiral Brownian motor and heat pump. Optimization of the construction predicts, for a nanoscale device, frequencies of the order of kHz and cooling rates of the order of femtojoule per second.

  11. Chiral Brownian heat pump

    OpenAIRE

    Van Den Broek, Martijn; Van Den Broeck, Christian

    2007-01-01

    We present the exact analysis of a chiral Brownian motor and heat pump. Optimization of the construction predicts, for a nanoscale device, frequencies of the order of kHz and cooling rates of the order of femtojoule per second.

  12. Regenerative Hydride Heat Pump

    Science.gov (United States)

    Jones, Jack A.

    1992-01-01

    Hydride heat pump features regenerative heating and single circulation loop. Counterflow heat exchangers accommodate different temperatures of FeTi and LaNi4.7Al0.3 subloops. Heating scheme increases efficiency.

  13. Mechanics of Thin Strip Steering in Hot Rolling

    Science.gov (United States)

    Jiang, Zhengyi; Tieu, Kiet A.

    2004-06-01

    The hot rolling of thin strip can result in several problems in hot rolling, for instance, the control of strip steering, strip shape and flatness and surface roughness etc. Therefore, the hot rolling of thin strip brings out a requirement of innovative technologies such as the extended control of shape and flatness, steering control and reduction of load by roll gap lubrication. In this paper, the authors focus on the analysis of thin strip snaking movement, as well as solve the related problems such as the shape and flatness due to a larger reduction applied when the strip is thinner. A finite element method was used to simulate this nonsymmetricity rolling considering the non-uniform reduction along the strip width. The calculated spread is compared with the measured values obtained from the rolling mill in laboratory and the friction effect is also discussed.

  14. Antenna with distributed strip and integrated electronic components

    Science.gov (United States)

    Rodenbeck, Christopher T.; Payne, Jason A.; Ottesen, Cory W.

    2008-08-05

    An antenna comprises electrical conductors arranged to form a radiating element including a folded line configuration and a distributed strip configuration, where the radiating element can be in proximity to a ground conductor and/or arranged as a dipole. Embodiments of the antenna include conductor patterns formed on a printed wiring board, having a ground plane, spacedly adjacent to and coplanar with the radiating element. An antenna can comprise a distributed strip patterned on a printed wiring board, integrated with electronic components mounted on top of or below the distributed strip, and substantially within the extents of the distributed strip. Mounting of electronic components on top of or below the distributed strip has little effect on the performance of the antenna, and allows for realizing the combination of the antenna and integrated components in a compact form. An embodiment of the invention comprises an antenna including a distributed strip, integrated with a battery mounted on the distributed strip.

  15. Remotely Adjustable Hydraulic Pump

    Science.gov (United States)

    Kouns, H. H.; Gardner, L. D.

    1987-01-01

    Outlet pressure adjusted to match varying loads. Electrohydraulic servo has positioned sleeve in leftmost position, adjusting outlet pressure to maximum value. Sleeve in equilibrium position, with control land covering control port. For lowest pressure setting, sleeve shifted toward right by increased pressure on sleeve shoulder from servovalve. Pump used in aircraft and robots, where hydraulic actuators repeatedly turned on and off, changing pump load frequently and over wide range.

  16. Velocity selective optical pumping

    OpenAIRE

    Aminoff, C. G.; Pinard, M.

    1982-01-01

    We consider optical pumping with a quasi monochromatic tunable light beam, in the low intensity limit where a rate equation regime is obtained The velocity selective optical pumping (V.S.O.P.) introduces a correlation between atomic velocity and internal variables in the ground (or metastable) state. The aim of this article is to evaluate these atomic observables (orientation, alignment, population) as a function of velocity, using a phenomenological description of the relaxation effect of co...

  17. Lunar Base Heat Pump

    Science.gov (United States)

    Walker, D.; Fischbach, D.; Tetreault, R.

    1996-01-01

    The objective of this project was to investigate the feasibility of constructing a heat pump suitable for use as a heat rejection device in applications such as a lunar base. In this situation, direct heat rejection through the use of radiators is not possible at a temperature suitable for lde support systems. Initial analysis of a heat pump of this type called for a temperature lift of approximately 378 deg. K, which is considerably higher than is commonly called for in HVAC and refrigeration applications where heat pumps are most often employed. Also because of the variation of the rejection temperature (from 100 to 381 deg. K), extreme flexibility in the configuration and operation of the heat pump is required. A three-stage compression cycle using a refrigerant such as CFC-11 or HCFC-123 was formulated with operation possible with one, two or three stages of compression. Also, to meet the redundancy requirements, compression was divided up over multiple compressors in each stage. A control scheme was devised that allowed these multiple compressors to be operated as required so that the heat pump could perform with variable heat loads and rejection conditions. A prototype heat pump was designed and constructed to investigate the key elements of the high-lift heat pump concept. Control software was written and implemented in the prototype to allow fully automatic operation. The heat pump was capable of operation over a wide range of rejection temperatures and cooling loads, while maintaining cooling water temperature well within the required specification of 40 deg. C +/- 1.7 deg. C. This performance was verified through testing.

  18. PRESUPPOSITIONS AND IMPLICATURES IN COMIC STRIPS

    Directory of Open Access Journals (Sweden)

    Ienneke Indra Dewi

    2008-05-01

    Full Text Available Article aimed to find out the role of presuppositions, implicatures, as well as to see the maxims violated or flouted in the comic strips i.e. to whether there is a miscommunication among the characters in the comic strips. Data were taken from the three comics, those are Peanuts, Andy, and Tintin, and were analysed based on the pattern that the sender made a presupposition before transferring information and the receiver would try to get the implied message. The results show that presuppositions and implicatures are much influenced by the background knowledge. The more the speaker and hearer know each other’s background, the better presuppositions and implicatures they make and finally, the less miscommunication occurred.

  19. Operation of a Batch Stripping Distillation Column

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A stripping batch distillation column is preferred when the amount of the light component in the feed is small and the products are to be recovered at high purity. The operation modes of a batch stripping are believed to be the same as those of a rectifier. However, the control system of a stripper is different. In this paper, we explore three different control methods with Hysys (Hyprotech Ltd. 1997) for a batch stripper. The main difference is the control scheme for reboiler liquid level: (a) controlled by reflux flow; (b) controlled by reboiler heat duty; (c) controlled by bottom product flow. The main characteristics of operating a batch stripper with different control scheme are presented in this paper. Guidelines are provided for the startup of a batch stripper, the effects of somecontrol tuning parameters on the column performance are discussed.

  20. L-strip proximity fed ga

    Directory of Open Access Journals (Sweden)

    Ashish Singh

    2014-03-01

    Full Text Available In this article, the analysis of dualband L-strip fed compact semi-circular disk microstrip patch antenna has been presented using circuit theory concept. The antenna parameters such as return loss, VSWR and radiation pattern are calculated. The effect of geometric dimensions of the proposed antenna such as length of vertical and horizontal portion of L-strip is investigated. It is found that antenna resonate at two distinct modes i.e. 1.3 GHz and 6.13 GHz for lower and upper resonance frequencies respectively. The bandwidth of the proposed antenna at lower resonance frequency is 6.61% (simulated and 10.64% (theoretical whereas at upper resonance frequency, it is 6.02% (simulated and 9.06 % (theoretical. The theoretical results are compared with IE3D simulation results as well as experimental results and they are in close agreement.

  1. Frequency dependent magnetization of superconductor strip

    Energy Technology Data Exchange (ETDEWEB)

    Thakur, Kailash Prasad [Landcare Research, Palmerston North (New Zealand); Raj, Ashish [Computer Science in Radiology, Weill Medical College, Cornell University, NY (United States); Brandt, Ernst Helmut [Max-Planck-Institut fuer Metallforschung, POB 800665, D-70506 Stuttgart (Germany); Sastry, Pamidi V P S S, E-mail: thakurk@landcareresearch.co.nz, E-mail: asr2004@med.cornell.edu, E-mail: ehb@mf.mpg.de, E-mail: pamidi@caps.fsu.edu [Center for Advanced Power Systems, Florida State University, Tallahassee, FL 32310 (United States)

    2011-04-15

    The frequency dependence of magnetic ac loss of thin superconductor strip subjected to an ac magnetic field perpendicular to the surface of the strip is investigated by incorporating a flux creep model into the critical state model of Brandt and Indenbom. It is found that the reduced ac loss exhibits a maximum value at a frequency f{sub m}, which is a rapidly varying function of the applied ac magnetic field. At low magnetic field, f{sub m} becomes zero, and ac loss decreases with frequency as a power law ({approx}f{sup -2/n}). Whereas at high magnetic field f{sub m} becomes infinite and ac loss increases with frequency, still following the power law ({approx}f{sup 1/n}). The analytical results are substantiated with experimental data and the results of a 2D finite element simulation.

  2. The Extent of the Stop Coannihilation Strip

    CERN Document Server

    Ellis, John; Zheng, Jiaming

    2014-01-01

    Many supersymmetric models such as the CMSSM feature a strip in parameter space where the lightest neutralino \\chi is identified as the lightest supersymmetric particle (LSP), the lighter stop squark \\tilde t_1 is the next-to-lightest supersymmetric particle (NLSP), and the relic \\chi cold dark matter density is brought into the range allowed by astrophysics and cosmology by coannihilation with the lighter stop squark \\tilde t_1 NLSP. We calculate the stop coannihilation strip in the CMSSM, incorporating Sommerfeld enhancement effects, and explore the relevant phenomenological constraints and phenomenological signatures. In particular, we show that the \\tilde t_1 may weigh several TeV, and its lifetime may be in the nanosecond range, features that are more general than the specific CMSSM scenarios that we study in this paper.

  3. Coiling Temperature Control in Hot Strip Mill

    Science.gov (United States)

    Imanari, Hiroyuki; Fujiyama, Hiroaki

    Coiling temperature is one of the most significant factors in products of hot strip mill to determine material properties such as strength, toughness of steel, so it is very important to achieve accurate coiling temperature control (CTC). Usually there are a few pyrometers on the run out table in hot strip mill, therefore temperature model and its adapting system have large influences on the accuracy of CTC. Also unscheduled change of rolling speed has a bad effect to keep coiling temperature as its target. Newly developed CTC system is able to get very accurate coiling temperature against uncertain factors and disturbances by adopting easily identified temperature model, learning method and dynamic set up function. The features of the CTC system are discussed with actual data, and the effectiveness of the system is shown by actual control results.

  4. ITCS Test Strip Development and Certification

    Science.gov (United States)

    Carrigan, Caitlin; Adam, Niklas; Pickering, Karen; Gazda, Daniel; Piowaty, Hailey

    2011-01-01

    Internal coolant loops used for International Space Station thermal control must be periodically monitored for system health, including pH, biocide levels and any indication of ammonia. The presence of ammonia, possible via a microleak in the interface between the internal and external thermal control systems, could be a danger to the crew. The Internal Thermal Control System (ITCS) Sampling Kit uses test strips as a colorimetric indicator of pH and concentrations of biocide and free ammonia. This paper describes the challenges in designing an ammonia colorimetric indicator in a variable pH environment, as well as lessons learned, ultimately resulting in a robust test strip to indicate a hazardous ammonia leak.

  5. BIOMATERIALS FOR ROTARY BLOOD PUMPS

    NARCIS (Netherlands)

    VANOEVEREN, W

    1995-01-01

    Rotary blood pumps are used for cardiac assist and cardiopulmonary support since mechanical blood damage is less than with conventional roller pumps. The high shear rate in the rotary pump and the reduced anticoagulation of the patient during prolonged pumping enforces high demands on the biocompati

  6. Pumping a playground swing.

    Science.gov (United States)

    Post, Auke A; de Groot, Gert; Daffertshofer, Andreas; Beek, Peter J

    2007-04-01

    In mechanical studies of pumping a playground swing, two methods of energy insertion have been identified: parametric pumping and driven oscillation. While parametric pumping involves the systematic raising and lowering of the swinger's center of mass (CM) along the swing's radial axis (rope), driven oscillation may be conceived as rotation of the CM around a pivot point at a fixed distance to the point of suspension. We examined the relative contributions of those two methods of energy insertion by inviting 18 participants to pump a swing from standstill and by measuring and analyzing the swing-swinger system (defined by eight markers) in the sagittal plane. Overall, driven oscillation was found to play a major role and parametric pumping a subordinate role, although the relative contribution of driven oscillation decreased as swinging amplitude increased, whereas that of parametric pumping increased slightly. Principal component analysis revealed that the coordination pattern of the swing-swinger system was largely determined (up to 95%) by the swing's motion, while correlation analysis revealed that (within the remaining 5% of variance) trunk and leg rotations were strongly coupled.

  7. A Spinning Particle in a Mobius Strip

    CERN Document Server

    Nieto, J A

    2011-01-01

    We develop the classical and quantum theory of a spinning particle moving in a Mobius strip. We first propose a Lagrangian for such a system and then we proceed to quantize the system via the constraint Hamiltonian system formalism. Our results may be of particular interest in several physical scenarios, including solid state physics and optics. In fact, the present work may shed some new light on the recent discoveries on condensed matter concerning topological insulators.

  8. Hot Strip Laminar Cooling Control Model

    Institute of Scientific and Technical Information of China (English)

    WANG Jun; WANG Guo-dong; LIU Xiang-hua

    2004-01-01

    The control model of laminar cooling system for hot strip, including air-cooling model, water-cooling model, temperature distribution model along thickness direction, feedforward control model, feedback control model and self-learning model, was introduced. PID arithmetic and Smith predictor controller were applied to feedback control. The sample of model parameter classification was given. The calculation process was shown by flow chart. The model has been proved to be simple, effective and of high precision.

  9. Mastering Interproximal Stripping: With Innovations in Slenderization

    OpenAIRE

    Sharma, Narendra Shriram; Shrivastav, Sunita S; Hazarey, Pushpa V

    2012-01-01

    ABSTRACT Crowding and irregularity remain a consistent problem for children. Management of space problems continues to play an important role in a dental practice. It also represents an area of major interaction between the primary provider and the specialists. Proximal stripping is routinely carried out to avoid extraction in borderline cases where space discrepancy is less and in cases where there is a discrepancy between the mesio- distal width of maxillary and mandibular teeth to satisfy ...

  10. Development of Silicon Multi-strip Detector

    Institute of Scientific and Technical Information of China (English)

    TanJilian; JinGenming; WangHongwei; YuanXiaohua; DuanLiming; LiSonglin; LuZiwei; XuHushan; NingBaojun; TianDayu; WangWei; ZhangLu

    2003-01-01

    Position sensitive detector is very important for nuclear physics experiment. There several techniques can be used to fabricate position sensitive detector, for example, Si-surface barrier method, diffusion method, ion implantation and planar process etc. Among all the techniques mentioned above planar process is the best one. We have developed batch of position sensitive detector -- silicon multi-strip detector by using planar process.

  11. Multitwist optical Möbius strips.

    Science.gov (United States)

    Freund, Isaac

    2010-01-15

    Circularly polarized Gauss-Laguerre GL00 and GL01 laser beams that cross at their waists at a small angle are shown to generate a quasi-paraxial field that contains a line of circular polarization, a C line, surrounded by polarization ellipses whose major and minor axes generate multitwist Möbius strips with twist numbers that increase with the distance from the C point.

  12. Sustainable Water and Energy in Gaza Strip

    Science.gov (United States)

    Hamdan, L.; Zarei, M.; Chianelli, R.; Gardner, E.

    2007-12-01

    Shortage of fresh water is a common problem in different areas of the world including the Middle East. Desalination of seawater and brackish water is the cheapest way to obtain fresh water in many regions. This research focuses on the situation in Gaza Strip where there is a severe shortage in the energy and water supply. The depletion of fresh water supplies and lack of wastewater treatments result in environmental problems. A solar powered cogeneration plant producing water and energy is proposed to be a suitable solution for Gaza Strip. Solar energy, using Concentrating Solar thermal Power (CSP) technologies, is used to produce electricity by a steam cycle power plant. Then the steam is directed to a desalination plant where it is used to heat the seawater to obtain freshwater. The main objective of this research is to outline a solution for the water problems in Gaza Strip, which includes a cogeneration (power and water) solar powered plant. The research includes four specific objectives: 1- an environmental and economic comparison between solar and fossil fuel energies; 2- technical details for the cogeneration plant; 3- cost and funding, 4- the benefits.

  13. High-Rate Capable Floating Strip Micromegas

    CERN Document Server

    Bortfeldt, Jonathan; Biebel, Otmar; Danger, Helge; Flierl, Bernhard; Hertenberger, Ralf; Lösel, Philipp; Moll, Samuel; Parodi, Katia; Rinaldi, Ilaria; Ruschke, Alexander; Zibell, André

    2015-01-01

    We report on the optimization of discharge insensitive floating strip Micromegas (MICRO-MEsh GASeous) detectors, fit for use in high-energy muon spectrometers. The suitability of these detectors for particle tracking is shown in high-background environments and at very high particle fluxes up to 60MHz/cm$^2$. Measurement and simulation of the microscopic discharge behavior have demonstrated the excellent discharge tolerance. A floating strip Micromegas with an active area of 48cm$\\times$50cm with 1920 copper anode strips exhibits in 120GeV pion beams a spatial resolution of 50$\\mu$m at detection efficiencies above 95%. Pulse height, spatial resolution and detection efficiency are homogeneous over the detector. Reconstruction of particle track inclination in a single detector plane is discussed, optimum angular resolutions below $5^\\circ$ are observed. Systematic deviations of this $\\mu$TPC-method are fully understood. The reconstruction capabilities for minimum ionizing muons are investigated in a 6.4cm$\\time...

  14. Wakes of ram pressure stripped disc galaxies

    CERN Document Server

    Roediger, E; Hoeft, M

    2006-01-01

    Spiral galaxies that move through the intracluster medium lose a substantial amount of their gas discs due to ram pressure stripping. The recent observations of NGC 4388 by Oosterloo & van Gorkom 2005 reveal a tail of stripped gas of ~ 100 kpc behind the source galaxy. We present first 3D hydrodynamical simulations of the evolution of such ram pressure stripped tails. We find that if the ICM wind does not vary significantly over a period of a few 100 Myr, subsonic galaxies produce a tail with regular features similar to a von-Karman vortex street. In this case, the tail widens systematically by about 45 kpc per 100 kpc distance behind the source galaxy. The widening rate is independent of the galaxy's inclination for a large range of inclinations. For supersonic galaxies, the tail is more irregular than for subsonic ones. The tail observed for NGC 4388 is narrower than the tails in our simulations. Reasons for this difference may be additional physical processes such as heat conduction or viscosity. In ad...

  15. Anodic stripping voltammetry enhancement by redox magnetohydrodynamics.

    Science.gov (United States)

    Clark, Emily A; Fritsch, Ingrid

    2004-04-15

    The effect of an external magnetic field on linear scan anodic stripping voltammetry (ASV) in solutions of 10(-6)-10(-7) M concentrations of lead, cadmium, and copper at mercury films on glassy carbon electrodes has been investigated. A high concentration of Hg(2+) was added to the analyte solution to induce a large cathodic current during the deposition step. Therefore, a large Lorentz force from the net flux of charge through the magnetic field resulted in convection due to magnetohydrodynamics. The faster delivery of analytes to the mercury film electrode during deposition caused an increase in the anodic stripping peaks. The effect of varying Hg(2+) concentrations (0-60 mM) and magnetic field strengths (0-1.77 T) on the enhancement of the stripping peaks was investigated. Enhancements as large as 129% for peak currents and 167% for peak areas were observed. An enhancement of approximately 100% was observed when 60 mM Fe(3+) replaced high concentrations of Hg(2+). This method of convection exhibits promise for small-volume ASV analysis with possible improved limits of detection and decreased preconcentration times.

  16. Inflation and deflation timing of the AutoCAT 2 WAVE intra-aortic balloon pump using the autoPilot mode in a clinical setting.

    Science.gov (United States)

    Bakker, E W M; Visser, K; van der Wal, A; Kuiper, M A; Koopmans, M; Breedveld, R

    2012-09-01

    The primary goal of this observational clinical study was to register the occurrence of incorrect inflation and deflation timing of an intra-aortic balloon pump in autoPilot mode. The secondary goal was to identify possible causes of incorrect timing. During IABP assistance of 60 patients, every four hours a strip was printed with the IABP frequency set to 1:2. Strips were examined for timing discrepancies beyond 40 ms from the dicrotic notch (inflation) and the end of the diastolic phase (deflation). In this way, 320 printed strips were examined. A total of 52 strips (16%) showed incorrect timing. On 24 of these strips, the incorrect timing was called incidental, as it showed on only one or a few beats. The other 28 cases of erroneous timing were called consistent, as more than 50% of the beats on the strip showed incorrect timing. We observed arrhythmia in 69% of all cases of incorrect timing. When timing was correct, arrhythmia was found on 13 (5%) of 268 strips. A poor quality electrocardiograph (ECG) signal showed on 37% of all strips with incorrect timing and 11% of all strips with proper timing. We conclude that inflation and deflation timing of the IABP is not always correct when using the autoPilot mode. The quality of the ECG input signal and the occurrence of arrhythmia appear to be related to erroneous timing. Switching from autoPilot mode to operator mode may not always prevent incorrect timing.

  17. Thermally Actuated Hydraulic Pumps

    Science.gov (United States)

    Jones, Jack; Ross, Ronald; Chao, Yi

    2008-01-01

    Thermally actuated hydraulic pumps have been proposed for diverse applications in which direct electrical or mechanical actuation is undesirable and the relative slowness of thermal actuation can be tolerated. The proposed pumps would not contain any sliding (wearing) parts in their compressors and, hence, could have long operational lifetimes. The basic principle of a pump according to the proposal is to utilize the thermal expansion and contraction of a wax or other phase-change material in contact with a hydraulic fluid in a rigid chamber. Heating the chamber and its contents from below to above the melting temperature of the phase-change material would cause the material to expand significantly, thus causing a substantial increase in hydraulic pressure and/or a substantial displacement of hydraulic fluid out of the chamber. Similarly, cooling the chamber and its contents from above to below the melting temperature of the phase-change material would cause the material to contract significantly, thus causing a substantial decrease in hydraulic pressure and/or a substantial displacement of hydraulic fluid into the chamber. The displacement of the hydraulic fluid could be used to drive a piston. The figure illustrates a simple example of a hydraulic jack driven by a thermally actuated hydraulic pump. The pump chamber would be a cylinder containing encapsulated wax pellets and containing radial fins to facilitate transfer of heat to and from the wax. The plastic encapsulation would serve as an oil/wax barrier and the remaining interior space could be filled with hydraulic oil. A filter would retain the encapsulated wax particles in the pump chamber while allowing the hydraulic oil to flow into and out of the chamber. In one important class of potential applications, thermally actuated hydraulic pumps, exploiting vertical ocean temperature gradients for heating and cooling as needed, would be used to vary hydraulic pressures to control buoyancy in undersea research

  18. A Opinião dos Turistas de Negócios sobre a Imagem da Cidade de São Paulo

    Directory of Open Access Journals (Sweden)

    Luis Noriega Vera

    2010-07-01

    Full Text Available Resumo O artigo apresenta a análise descritiva dos principais resultados obtidos em pesquisa de campo realizada entre a segunda quinzena de junho e primeira de julho do ano de 2006 nos dois aeroportos da cidade de São Paulo. A pesquisa teve como público alvo os turistas de negócios que visitam a cidade. A amostra foi escolhida intencionalmente e o critério de estratificação foi o local de residência permanente dos turistas. O principal objetivo da pesquisa foi aprimorar o entendimento sobre a avaliação da imagem de um destino turístico. Foi proposto um modelo conceitual a partir do referencial teórico sobre comportamento do consumidor existente nas áreas de turismo e marketing. Os resultados apontam que o perfil dos turistas é consistente com estudos anteriores e a imagem da cidade consolidada como destino de negócios. Em adição é destacada a qualidade dos serviços consumidos, a satisfação e a intenção do turista de retornar e indicar o destino a parentes e amigos. Palavras-chave: destino turístico; turista de negócios; avaliação de imagem; qualidade; lealdade. Abstract This article presents the descriptive analysis of the main results of a survey held from June 15th through July 15th 2006 in the two São Paulo City airports. The survey targeted business tourists visiting the city. It was used an intentional sample and the stratification parameter was tourists’ place of permanent residence. The main objective was to enhance the knowledge on tourism destination image evaluation. A conceptual model was proposed based on tourism and marketing literature consumer behavior theoretical background. The results obtained pointed out that tourist profile are consistent with prior studies and the consolidated city image as a business destination. It is also highlighted its service quality, satisfaction and tourist’s intention to return or indicate the destination to relatives and friends. Keywords: tourism

  19. LEP Vacuum Chamber

    CERN Multimedia

    1983-01-01

    This is a cut-out of a LEP vacuum chamber for dipole magnets showing the beam channel and the pumping channel with the getter (NEG) strip and its insulating supports. A water pipe connected to the cooling channel can also be seen at the back.The lead radiation shield lining is also shown. See also 8305563X.

  20. Electronic Unit Pump Test Bench Development and Pump Properties Research

    Institute of Scientific and Technical Information of China (English)

    LIU Bo-lan; HUANG Ying; ZHANG Fu-jun; ZHAO Chang-lu

    2006-01-01

    A unit pump test bench is developed on an in-line pump test platform. The bench is composed of pump adapting assembly, fuel supply subsystem, lubricating subsystem and a control unit. A crank angle domain injection control method is given out and the control accuracy can be 0.1° crank degree. The bench can test bot h mechanical unit pump and electronic unit pump. A test model-PLD12 electronic unit pump is tested. Full pump delivery map and some influence factors test is d one. Experimental results show that the injection quantity is linear with the de livery angle. The quantity change rate is 15% when fuel temperature increases 30℃. The delivery quantity per cycle increases 30mg at 28V drive voltage. T he average delivery difference for two same type pumps is 5%. Test results show that the bench can be used for unit pump verification.

  1. Effect of boron on hot strips of low carbon steel produced by compact strip production

    Institute of Scientific and Technical Information of China (English)

    Hao Yu; Yonglin Kang

    2008-01-01

    The effect of boron on hot strips of low carbon steel produced by compact strip production (CSP) to reduce the strength to a certain degree was investigated, which is quite different from that of high-strength low alloy steel. The mechanical properties and microstructural evolution of the hot strip were studied using optical microscopy and tensile tests. By means of an electrolytic disso- lution technique and Thermo-Cal calculation, the precipitates containing boron were analyzed and detected. From the electron back- scattered diffraction analysis, it can be deciphered whether the microstructure has recrystallized or not. Furthermore, the effect of boron segregation on the recrystallization or non-recrystallization conditions can be distinguished. The segregation behavior of boron was investigated in boron-containing steel. The nonequilibrium segregation of boron during processing was discussed on the basis of the forming complexes with vacancies that migrate to the boundaries prior to annihilation, which was confirmed by the subsequent cold rolling with annealing experiments.

  2. Modelagem de processos de negócios na implementação de ERPs nacionais em PMEs Business processes modeling in the implementation of national ERPs within SMEs

    National Research Council Canada - National Science Library

    Fernanda Pereira Carneiro da Silva; Néocles Alves Pereira

    2006-01-01

    ... implementação para otimizar a integração dos processos internos dos negócios.This article presents evidences found in a research whose objective was to investigate the contribution of using business processes modeling (BPM...

  3. Photo-dynamics of the lyophilized photo-activated adenylate cyclase NgPAC2 from the amoeboflagellate Naegleria gruberi NEG-M strain

    Science.gov (United States)

    Penzkofer, A.; Tanwar, M.; Veetil, S. K.; Kateriya, S.; Stierl, M.; Hegemann, P.

    2013-09-01

    The absorption and emission spectroscopic behavior of lyophilized photo-activated adenylate cyclase NgPAC2 from the amoeboflagellate Naegleria gruberi NEG-M strain consisting of a BLUF domain (BLUF = Blue Light sensor Using Flavin) and a cyclase homology domain was studied in the dark, during blue-light exposure and after blue-light exposure at a temperature of 4 °C. The BLUF domain photo-cycle dynamics observed for snap-frozen NgPAC2 was lost by lyophilization (no signaling state formation with flavin absorption red-shift). Instead, blue-light photo-excitation of lyophilized NgPAC2 caused sterically restricted Tyr-Tyr cross-linking (o,o‧-ditysosine formation) and partial flavin cofactor reduction.

  4. Uma análise do ambiente de negócios da indústria bancária comercial

    Directory of Open Access Journals (Sweden)

    Lauro M. Tachibana

    2004-01-01

    Full Text Available A indústria bancária comercial brasileira passou por razoáveis modificações nos últimos anos, devido ao fim da hiperinflação, à entrada dos bancos estrangeiros, às privatizações e a outros fatores. Mesmo com esse cenário, os bancos comerciais mantiveram alta rentabilidade em decorrência de um quadro de altas taxas de juros e da capacidade e flexibilidade para se adaptarem ao ambiente macroeconômico. Este trabalho tem por objetivo fazer uma análise prospectiva do ambiente de negócios da indústria bancária comercial, considerando o cenário macroeconômico para os próximos anos.

  5. Plano de negócio : empresa no setor da restauração e animação

    OpenAIRE

    2015-01-01

    Mestrado em Ciências Empresariais O presente trabalho vem no seguimento do Trabalho Final de Mestrado do curso de Ciências Empresariais do ISEG. O seu principal objetivo é a elaboração de um plano de negócios no setor da restauração e animação, e a avaliação do mesmo a nível técnico, económico e financeiro. Numa primeira fase, foi efetuada uma análise contextual à envolvente onde a empresa proposta se insere e, em seguida, analisado o setor onde esta se inclui. Posteriormente, realizou...

  6. Congruências entre posicionamentos estratégicos e redes de negócios: estudo de caso de uma subsidiária brasileira

    Directory of Open Access Journals (Sweden)

    Márcio Roberto Moran

    2012-03-01

    Full Text Available Na pesquisa exploratória aqui relatada, realizada em 2009 e guiada por uma extensa revisão bibliográfica e pelo emprego do método de estudo de caso, busca-se identificar congruências entre o posicionamento estratégico adotado pela subsidiária brasileira de uma corporação multinacional e o tipo de rede de negócios por ela integrada. Apoiando-se em dois modelos específicos da literatura acadêmica sobre os temas mencionados (posicionamento estratégico e redes, as conclusões dessa investigação sugerem que as Redes Verticais de Demanda e Fornecimento (MOLLER e RAJALA, 2007 são adequadas para operacionalizar o posicionamento definido como Melhor Produto no Modelo Delta (HAX e WILDE II, 1999; 2001.

  7. Elaboração do mapa de recursos: processo de apoio ao planejamento de um novo negócio de internet

    Directory of Open Access Journals (Sweden)

    Josué Vitor de Medeiros Júnior

    2015-10-01

    Full Text Available O artigo tem como objetivo apresentar a aplicação de um método de elaboração do Mapa de Recursos para apoiar o planejamento de um novo negócio baseado na internet a partir da percepção do seu empreendedor. O mapa de recursos resultante é uma representação visual das inter-relações entre os recursos estratégicos, assim caracterizados em função dos pressupostos teóricos da Visão Baseada em Recursos (VBR, bem como da Dinâmica de Sistemas, que caracteriza tais representações por enlaces de feedback, fluxos e acumulações, responsáveis por comportamentos de aspectos sistêmicos como o desempenho organizacional. Em relação a metodologia, a pesquisa se caracteriza como exploratória descritiva, subtipo estudo de caso e para a coleta de dados foram utilizados questionários e entrevistas com o empreendedor responsável pelo negócio. O método da elaboração do mapa ocorreu em algumas etapas como levantamento e seleção dos recursos estratégicos da empresa, definição dos fluxos de acúmulo dos recursos e os relacionamentos entre eles, identificação das políticas de desenvolvimento dos recursos, incorporação de variáveis financeiras e identificação das capacidades responsáveis pelo desenvolvimento do negócio. Como resultados da pesquisa, obteve-se a identificação e classificação dos recursos estratégicos da organização e como esses recursos se inter-relacionam e impactam no seu desempenho. A originalidade do trabalho se justifica pela construção do mapa de recursos em uma empresa nascente, auxiliando o empreendedor a identificar e explorar os recursos estratégicos iniciais e como a tomada de decisão por parte do empreendedor pode impactar no desempenho da empresa. Como contribuição, o processo de elaboração do mapa, através de uma representação visual não linear dos recursos estratégicos, a partir do modelo mental do empreendedor, mostrou-se como um processo de aprendizado e reflexão sobre

  8. Heat driven pulse pump

    Science.gov (United States)

    Benner, Steve M (Inventor); Martins, Mario S. (Inventor)

    2000-01-01

    A heat driven pulse pump includes a chamber having an inlet port, an outlet port, two check valves, a wick, and a heater. The chamber may include a plurality of grooves inside wall of the chamber. When heated within the chamber, a liquid to be pumped vaporizes and creates pressure head that expels the liquid through the outlet port. As liquid separating means, the wick, disposed within the chamber, is to allow, when saturated with the liquid, the passage of only liquid being forced by the pressure head in the chamber, preventing the vapor from exiting from the chamber through the outlet port. A plurality of grooves along the inside surface wall of the chamber can sustain the liquid, which is amount enough to produce vapor for the pressure head in the chamber. With only two simple moving parts, two check valves, the heat driven pulse pump can effectively function over the long lifetimes without maintenance or replacement. For continuous flow of the liquid to be pumped a plurality of pumps may be connected in parallel.

  9. Uranium stripping from tributyl phosphate by urea solutions

    Science.gov (United States)

    Skripchenko, S. Yu.; Titova, S. M.; Smirnov, A. L.; Rychkov, V. N.

    2016-09-01

    The process of uranium stripping from tri-n-butyl phosphate in kerosene by urea solutions was investigated at the volume ratio of the organic and aqueous phases of (1-10) : 1 in the temperature range of 20-60 °C. The stripping of uranium from a loaded organic phase increased with increasing urea content in the solution and with increasing temperature. Maximum recovery of uranium from tributyl phosphate was obtained using a solution that contained 8-12 mol/l of urea. The application of a urea solution for uranium stripping resulted in the strip product solution containing 200-240 g/L of uranium. The process of uranium stripping by dilute nitric acid was also investigated. Results of uranium stripping by the two methods are compared and discussed.

  10. Pulsed differential pumping system

    Energy Technology Data Exchange (ETDEWEB)

    Antipov, G.N.; Bagautdinov, F.A.; Rybalov, S.V.

    1985-06-01

    A pulsed differential pumping system is described for extracting an electron beam from a shaping region at a pressure of 10/sup -5/ torr into a volume with a pressure of 10-100 torr. A fast valve is used with appropriate geometrical parameters to reduce the length of the outlet channel considerable while increasing its diameter. Test results are given. The pumping system has two sections which communicate one with the other and with the volume at the elevated pressure which is produced by gasdynamic nozzles.

  11. Heat pump planning handbook

    CERN Document Server

    Bonin, Jürgen

    2015-01-01

    The Heat Pump Planning Handbook contains practical information and guidance on the design, planning and selection of heat pump systems, allowing engineers, designers, architects and construction specialists to compare a number of different systems and options. Including detailed descriptions of components and their functions and reflecting the current state of technology this guide contains sample tasks and solutions as well as new model calculations and planning evaluations. Also economic factors and alternative energy sources are covered, which are essential at a time of rising heat costs. T

  12. Sorption product heat pump

    Energy Technology Data Exchange (ETDEWEB)

    Antonini, G.; Francois, O.; Gendarme, J.P.; Guilleminot, J.J.; Meunier, F.

    1988-07-15

    A continuous operating, and thus with enhanced performance, heat pump is presented. In this heat pump, the heat transfer between the hot source and the output system or network is realized through a solid adsorbent-refrigerant couple having endothermal desorption properties and exothermal adsorption or absorption properties. The sorption products are carried in a closed cycle movement between the two parts of the reactor. Each side of the reactor is assuming always the same function and the thermal inertia have to be overcome only when starting the reactor.

  13. Regenerative adsorbent heat pump

    Science.gov (United States)

    Jones, Jack A. (Inventor)

    1991-01-01

    A regenerative adsorbent heat pump process and system is provided which can regenerate a high percentage of the sensible heat of the system and at least a portion of the heat of adsorption. A series of at least four compressors containing an adsorbent is provided. A large amount of heat is transferred from compressor to compressor so that heat is regenerated. The process and system are useful for air conditioning rooms, providing room heat in the winter or for hot water heating throughout the year, and, in general, for pumping heat from a lower temperature to a higher temperature.

  14. Geothermal Heat Pump Performance

    Energy Technology Data Exchange (ETDEWEB)

    Boyd, Tonya L.; Lienau, Paul J.

    1995-01-01

    Geothermal heat pump systems are a promising new energy technology that has shown rapid increase in usage over the past ten years in the United States. These systems offer substantial benefits to customers and utilities in energy (kWh) and demand (kW) savings. The purpose of this study was to determine what existing monitored data was available mainly from electric utilities on heat pump performance, energy savings and demand reduction for residential, school, and commercial building applications. Information was developed on the status of electric utility marketing programs, barriers to market penetration, incentive programs, and benefits.

  15. Geothermal heat pump performance

    Energy Technology Data Exchange (ETDEWEB)

    Boyd, Tonya L.; Lienau, Paul J.

    1995-01-01

    Geothermal heat pump systems are a promising new energy technology that has shown rapid increase in usage over the past ten years in the United States. These systems offer substantial benefits to customers and utilities in energy (kWh) and demand (kW) savings. The purpose of this study was to determine what existing monitored data was available mainly from electric utilities on heat pump performance, energy savings and demand reduction for residential, school, and commercial building applications. Information was developed on the status of electric utility marketing programs, barriers to market penetration, incentive programs, and benefits.

  16. Molecular heat pump.

    Science.gov (United States)

    Segal, Dvira; Nitzan, Abraham

    2006-02-01

    We propose a molecular device that pumps heat against a thermal gradient. The system consists of a molecular element connecting two thermal reservoirs that are characterized by different spectral properties. The pumping action is achieved by applying an external force that periodically modulates molecular levels. This modulation affects periodic oscillations of the internal temperature of the molecule and the strength of its coupling to each reservoir resulting in a net heat flow in the desired direction. The heat flow is examined in the slow and fast modulation limits and for different modulation wave forms, thus making it possible to optimize the device performance.

  17. High pressure water jet cutting and stripping

    Science.gov (United States)

    Hoppe, David T.; Babai, Majid K.

    1991-01-01

    High pressure water cutting techniques have a wide range of applications to the American space effort. Hydroblasting techniques are commonly used during the refurbishment of the reusable solid rocket motors. The process can be controlled to strip a thermal protective ablator without incurring any damage to the painted surface underneath by using a variation of possible parameters. Hydroblasting is a technique which is easily automated. Automation removes personnel from the hostile environment of the high pressure water. Computer controlled robots can perform the same task in a fraction of the time that would be required by manual operation.

  18. Fermilab silicon strip readout chip for BTev

    Energy Technology Data Exchange (ETDEWEB)

    Yarema, Raymond; Hoff, Jim; Mekkaoui, Abderrezak; Manghisoni, Massimo; Re, Valerio; Angeleri, Valentina; Manfredi, Pier Francesco; Ratti, Lodovico; Speziali, Valeria; /Fermilab /Bergamo U. /INFN, Pavia /Pavia U.

    2005-05-01

    A chip has been developed for reading out the silicon strip detectors in the new BTeV colliding beam experiment at Fermilab. The chip has been designed in a 0.25 {micro}m CMOS technology for high radiation tolerance. Numerous programmable features have been added to the chip, such as setup for operation at different beam crossing intervals. A full size chip has been fabricated and successfully tested. The design philosophy, circuit features, and test results are presented in this paper.

  19. Intelligent Control on Hot Strip Coiling Temperature

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    A new intelligent control scheme for hot strip coiling temperature is presented. In this scheme, the prediction model of finishing temperature and the presetting model of main cooling zone are establish based on BP neural network, the feed-forward open-loop control model of main cooling zone is constructed based on T-S fuzzy neural network, a new improved structure of T-S fuzzy neural network is developed, and the feedback close-loop control model of precision cooling zone is obtained based on fuzzy control. The effectiveness of the proposed scheme has been demonstrated by computer simulation with a satisfactory result.

  20. Gas Stripping in the Simulated Pegasus Galaxy

    Science.gov (United States)

    Mercado, Francisco Javier; Samaniego, Alejandro; Wheeler, Coral; Bullock, James

    2017-01-01

    We utilize the hydrodynamic simulation code GIZMO to construct a non-cosmological idealized dwarf galaxy built to match the parameters of the observed Pegasus dwarf galaxy. This simulated galaxy will be used in a series of tests in which we will implement different methods of removing the dwarf’s gas in order to emulate the ram pressure stripping mechanism encountered by dwarf galaxies as they fall into more massive companion galaxies. These scenarios will be analyzed in order to determine the role that the removal of gas plays in rotational vs. dispersion support (Vrot/σ) of our galaxy.

  1. Beam Test Results for MSGC's with Thick Metal Strips.

    CERN Document Server

    Beaumont, W; Bernier, K; Bouhali, O; Boulogne, I; Daubie, Evelyne; De Troy, J G; Delentdecker, G; Devroede, O; Gregoire,,; Iacopi, F; Udo, Fred; Van Doninck, W K; Van Dyck, C; Van Lancker, L; Van der Velde, C; Verbeure, F; Zhukov, V

    1999-01-01

    Micro Strip Gas Counters with robust gold strips have been developed at IMEC, the Interuniversity Microelectronics Center at Leuven, in Belgium. The electroless plating technology was used, allowing to achieve a strip thickness of up to 1.6 mu m on 10 X 10 cm**2 substrates. Results on signal to noise ratio, spark rate, resulting damages and detector occupancy are presented for counters exposed to various intensities of heavily ionizing particles.

  2. Study on Production of Rubber Sealing Strips with Steel Bones

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Rubber sealing strips with steel bones are used in car manufacturing that produced in large quantities. Cutting processes, such as milling and punching, are needed when the strips are produced. Accuracy, smoothness and flatness of the machined surface have to be guaranteed in the cutting process; moreover, deformation of the steel bone and peeling-off of the rubber must be avoided. Therefore cutting action of rubber/steel strips differs from that of rubber or metal workpiece separately. In this paper, milli...

  3. Time domain non linear strip theory for ship motions

    OpenAIRE

    Fan, Y.T.; Wilson, P. A.

    2004-01-01

    A new implementation of strip theory is proposed based on the strip theory by Salvesen, et al. [1] and early work by Westlake and Wilson [2]. Compared with traditional strip theory, the main difference is that the calculation is carried out in the time domain. This makes it possible to cope with relatively large-amplitude motions and non-constant forward speed problems. At each time step, the exact underwater sections are extracted; the velocity potential is required to satisfyt...

  4. Factors Influencing Bonding Strength of Laminated Bamboo Strips Lumber

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    Factors influencing bonding strength of laminated bamboo strips lumber (LBSL) were investigated in this paper. In order to find an optimized technology, this paper investigated how the thickness of bamboo strips, the assembly orientation of bamboo curtain, the type of adhesives, as well as coupling agent treatment of bamboo curtain affected the bonding strength. The following conclusions were drawn: 1)The thinner the thickness of the bamboo strips, the bigger the bonding strength of LBSL; 2) The assembly or...

  5. Terminal Strip Facilitates Printed-Circuit Board Changes

    Science.gov (United States)

    Pinto, E. A.; Mcosker, C. E.

    1983-01-01

    Laminanted copper and polyimide terminal strip makes it easy to modify printed-circuit (PC) board, after board has been fabricated. When epoxied over conductors or insulating portion of PC board, strip provides series of solder-coated copper conductor pads to which integrated-circuit leads are soldered for functional changes. Terminal strips accommodate leads on dual inline IC package or as staggered single or multiple leads on planar mounted flatpacks.

  6. Space Vehicle Heat Shield Having Edgewise Strips of Ablative Material

    Science.gov (United States)

    Blosser, Max L. (Inventor); Poteet, Carl C. (Inventor); Bouslog, Stan A. (Inventor)

    2015-01-01

    A heat shield for a space vehicle comprises a plurality of phenolic impregnated carbon ablator (PICA) blocks secured to a surface of the space vehicle and arranged in a pattern with gaps therebetween. The heat shield further comprises a plurality of PICA strips disposed in the gaps between the PICA blocks. The PICA strips are mounted edgewise, such that the structural orientation of the PICA strips is substantially perpendicular to the structural orientation of the PICA blocks.

  7. Clad strip casting by a twin roll caster

    OpenAIRE

    T. Haga; Nakamura, R; S. Kumai; H. Watari

    2009-01-01

    Purpose: Of this paper is to realize the casting of the clad strip by only one process. Therefore, the investigation of the ability of the casting of the clad strip by a vertical type twin roll caster was operated. The aim of the use of the twin roll caster to make clad strip was in the reduction of the production-energy of the clad strip.Design/methodology/approach: Used in the present study was a vertical type twin roll caster with the scriber. The scriber was used to prevent the mixture of...

  8. Three-Dimensional Model for Strip Hot Rolling

    Institute of Scientific and Technical Information of China (English)

    ZHANG Guo-min; XIAO Hong; WANG Chun-hua

    2006-01-01

    A three-dimensional model for strip hot rolling was developed, in which the plastic deformation of strip, the thermal crown of rolls, roll deflection and flattening were calculated by rigid-plastic finite element method, finite difference method, influential function method and elastic finite element method respectively. The roll wear was taken into consideration. The model can provide detailed information such as rolling pressure distribution, contact pressure distribution between backup rolls and work rolls, deflection and flattening of work rolls, lateral distribution of strip thickness, and lateral distribution of front and back tensions. The finish rolling on a 1 450 mm hot strip mill was simulated.

  9. Stripped elliptical galaxies as probes of ICM physics: I. Tails, wakes, and flow patterns in and around stripped ellipticals

    CERN Document Server

    Roediger, E; Nulsen, P E J; Forman, W R; Machacek, M; Randall, S; Jones, C; Churazov, E; Kokotanekova, R

    2014-01-01

    (abridged) Elliptical cluster galaxies are successively stripped of their gaseous atmospheres due to their motion through the ICM. The stripped galactic gas forms a 'tail' in the galaxy's wake. Deep X-ray observations reveal the fine-structure of the gas tail and of the interface between galactic gas and ICM. This fine-structure depends on dynamic conditions (galaxy potential, initial gas contents, orbit in the host cluster), stripping stage (early infall, pre-/post-pericenter passage), and on the still ill-constrained ICM plasma properties (thermal conductivity, viscosity, magnetic field structure). In a series of papers, we aim at disentangling dynamic and plasma effects in order to use observed stripped ellipticals as probes of the ICM plasma properties. This first paper determines flow phases and flow patterns of successive gas stripping by means of hydrodynamical simulations. During quasi-steady stripping, the flow of ICM around the remnant atmosphere is similar to the flow around solid bodies, including...

  10. Cold Climate Heat Pumps Using Tandem Compressors

    Energy Technology Data Exchange (ETDEWEB)

    Shen, Bo [ORNL; Abdelaziz, Omar [ORNL; Rice, C Keith [ORNL; Baxter, Van D [ORNL

    2016-01-01

    In cold climate zones, e.g. ASHRAE climate regions IV and V, conventional electric air-source heat pumps (ASHP) do not work well, due to high compressor discharge temperatures, large pressure ratios and inadequate heating capacities at low ambient temperatures. Consequently, significant use of auxiliary strip heating is required to meet the building heating load. We introduce innovative ASHP technologies as part of continuing efforts to eliminate auxiliary strip heat use and maximize heating COP with acceptable cost-effectiveness and reliability. These innovative ASHP were developed using tandem compressors, which are capable of augmenting heating capacity at low temperatures and maintain superior part-load operation efficiency at moderate temperatures. Two options of tandem compressors were studied; the first employs two identical, single-speed compressors, and the second employs two identical, vapor-injection compressors. The investigations were based on system modeling and laboratory evaluation. Both designs have successfully met the performance criteria. Laboratory evaluation showed that the tandem, single-speed compressor ASHP system is able to achieve heating COP = 4.2 at 47 F (8.3 C), COP = 2.9 at 17 F (-8.3 C), and 76% rated capacity and COP = 1.9 at -13 F (-25 C). This yields a HSPF = 11.0 (per AHRI 210/240). The tandem, vapor-injection ASHP is able to reach heating COP = 4.4 at 47 F, COP = 3.1 at 17 F, and 88% rated capacity and COP = 2.0 at -13 F. This yields a HSPF = 12.0. The system modeling and further laboratory evaluation are presented in the paper.

  11. Pressurized Vessel Slurry Pumping

    Energy Technology Data Exchange (ETDEWEB)

    Pound, C.R.

    2001-09-17

    This report summarizes testing of an alternate ''pressurized vessel slurry pumping'' apparatus. The principle is similar to rural domestic water systems and ''acid eggs'' used in chemical laboratories in that material is extruded by displacement with compressed air.

  12. Microfluidic "blinking" bubble pump

    NARCIS (Netherlands)

    Yin, Zhizhong; Prosperetti, Andrea

    2005-01-01

    The paper reports data obtained on a simple micropump, suitable for electrolytes, based on the periodic growth and collapse of a single vapor bubble in a microchannel. With a channel diameter of the order of 100 µm, pumping rates of several tens of µl/min and pressure differences of several kPa are

  13. Cold Climate Heat Pump

    Science.gov (United States)

    2013-08-01

    12. Data set 7 – energy consumption of heat pump and furnace ................................ 22 Figure 13. Experimentally adjusted TRNSYS model...minute SCF standard cubic feet SEER seasonal energy efficiency ratio SH superheated TMY Typical Meteorological Year TRNSYS Transient Systems...Simulation Program ( TRNSYS ), to generate an experimentally adjusted, simulation heating seasonal performance. 6.4.1 Simulation Results The TRNSYS model

  14. The Osmotic Pump

    Science.gov (United States)

    Levenspiel, Octave; de Nevers, Noel

    1974-01-01

    Describes the principle involved in an osmotic pump used to extract fresh water from the oceans and in an osmotic power plant used to generate electricity. Although shown to be thermodynamically feasible, the osmotic principle is not likely to be used commerically for these purposes in the near future. (JR)

  15. Therapeutic surfactant-stripped frozen micelles

    Science.gov (United States)

    Zhang, Yumiao; Song, Wentao; Geng, Jumin; Chitgupi, Upendra; Unsal, Hande; Federizon, Jasmin; Rzayev, Javid; Sukumaran, Dinesh K.; Alexandridis, Paschalis; Lovell, Jonathan F.

    2016-05-01

    Injectable hydrophobic drugs are typically dissolved in surfactants and non-aqueous solvents which can induce negative side-effects. Alternatives like `top-down' fine milling of excipient-free injectable drug suspensions are not yet clinically viable and `bottom-up' self-assembled delivery systems usually substitute one solubilizing excipient for another, bringing new issues to consider. Here, we show that Pluronic (Poloxamer) block copolymers are amenable to low-temperature processing to strip away all free and loosely bound surfactant, leaving behind concentrated, kinetically frozen drug micelles containing minimal solubilizing excipient. This approach was validated for phylloquinone, cyclosporine, testosterone undecanoate, cabazitaxel and seven other bioactive molecules, achieving sizes between 45 and 160 nm and drug to solubilizer molar ratios 2-3 orders of magnitude higher than current formulations. Hypertonic saline or co-loaded cargo was found to prevent aggregation in some cases. Use of surfactant-stripped micelles avoided potential risks associated with other injectable formulations. Mechanistic insights are elucidated and therapeutic dose responses are demonstrated.

  16. SKULL-STRIPPING WITH DEFORMABLE ORGANISMS.

    Science.gov (United States)

    Prasad, Gautam; Joshi, Anand A; Thompson, Paul M; Toga, Arthur W; Shattuck, David W; Terzopoulos, Demetri

    2011-01-01

    Segmenting brain from non-brain tissue within magnetic resonance (MR) images of the human head, also known as skull-stripping, is a critical processing step in the analysis of neuroimaging data. Though many algorithms have been developed to address this problem, challenges remain. In this paper, we apply the "deformable organism" framework to the skull-stripping problem. Within this framework, deformable models are equipped with higher-level control mechanisms based on the principles of artificial life, including sensing, reactive behavior, knowledge representation, and proactive planning. Our new deformable organisms are governed by a high-level plan aimed at the fully-automated segmentation of various parts of the head in MR imagery, and they are able to cooperate in computing a robust and accurate segmentation. We applied our segmentation approach to a test set of human MRI data using manual delineations of the data as a reference "gold standard." We compare these results with results from three widely used methods using set-similarity metrics.

  17. Optimization of compound gear pump

    Institute of Scientific and Technical Information of China (English)

    栾振辉

    2002-01-01

    This paper introduces the performances of compound gear pump. Based on the target of having the smallest mass per unit volume, the paper established a mathematical model of optimization, and obtained the results of optimization of the pump.

  18. RSES heat pump technician certification

    Energy Technology Data Exchange (ETDEWEB)

    Zeiner, J.

    1996-06-01

    In 1987 the National Heat Pump certification test was developed by the Refrigeration Service Engineers Society (RSES), and in 1994, the program was more specifically named Heat Pump Service Technician Certification. This report describes the benefits of certification.

  19. Orbital Liquid Oxygen Pump Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This proposed work will develop a pump, which is based on two novel and unique design features. The first feature is a lobed pumping mechanism which operates with...

  20. Stream Surface Strip Element Method and Simulation of Three-Dimensional Deformation of Continuous Hot Rolled Strip

    Institute of Scientific and Technical Information of China (English)

    LIU Hong-min; WANG Ying-rui

    2004-01-01

    A new method, the stream surface strip element method, for simulating the three-dimensional deformation of plate and strip rolling process was proposed. The rolling deformation zone was divided into a number of stream surface (curved surface) strip elements along metal flow traces, and the stream surface strip elements were mapped into the corresponding plane strip elements for analysis and computation. The longitudinal distributions of the lateral displacement and the altitudinal displacement of metal were respectively constructed to be a quartic curve and a quadratic curve, of which the lateral distributions were expressed as the third-power spline function, and the altitudinal distributions were fitted in the quadratic curve. From the flow theory of plastic mechanics, the mathematical models of the three-dimensional deformations and stresses of the deformation zone were constructed. Compared with the streamline strip element method proposed by the first author of this paper, the stream surface strip element method takes into account the uneven distributions of stresses and deformations along altitudinal direction, and realizes the precise three-dimensional analysis and computation. The simulation example of continuous hot rolled strip indicates that the method and the model accord with facts and provide a new reliable engineering-computation method for the three-dimensional mechanics simulation of plate and strip rolling process.

  1. VIRTUAL FUEL-PUMP DESIGN

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Some concepts of virtual product are discussed. The key technologies of virtual fuel-pump development are in detail analysed, which include virtual fuel-pump product modeling, intelligent simulation, distributed design environment, and virtual assembly. The virtual fuel-pump development prototype system considers requirement analysis, concept design, injection preferment analysis, detailed design, and assembly analysis.

  2. Small Scroll Pump for Cryogenic Liquids Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The innovation is a compact, reliable, light weight, electrically driven pump capable of pumping cryogenic liquids, based on scroll pump technology. This pump will...

  3. Improving pumping system efficiency at coal plants

    Energy Technology Data Exchange (ETDEWEB)

    Livoti, W.C.; McCandless, S.; Poltorak, R. [Baldor Electric Co. (United States)

    2009-03-15

    The industry must employ ultramodern technologies when building or upgrading power plant pumping systems thereby using fuels more efficiently. The article discusses the uses and efficiencies of positive displacement pumps, centrifugal pumps and multiple screw pumps. 1 ref., 4 figs.

  4. Pumping characteristics of roots blower pumps for light element gases

    Energy Technology Data Exchange (ETDEWEB)

    Hiroki, Seiji; Abe, Tetsuya; Tanzawa, Sadamitsu; Nakamura, Jun-ichi; Ohbayashi, Tetsuro [Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan). Naka Fusion Research Establishment

    2002-07-01

    The pumping speed and compression ratio of the two-stage roots blower pumping system were measured for light element gases (H{sub 2}, D{sub 2} and He) and for N{sub 2}, in order to assess validity of the ITER torus roughing system as an ITER R and D task (T234). The pumping system of an Edwards EH1200 (nominal pumping speed of 1200 m{sup 3}/s), two EH250s (ibid. 250 m{sup 3}/s) and a backing pump (ibid. 100 m{sup 3}/s) in series connection was tested under PNEUROP standards. The maximum pumping speeds of the two-stage system for D{sub 2} and N{sub 2} were 1200 and 1300 m{sup 3}/h, respectively at 60 Hz, which satisfied the nominal pumping speed. These experimental data support the design validity of the ITER torus roughing system. (author)

  5. Metal films with imprinted nanostructures by template stripping

    DEFF Research Database (Denmark)

    Eriksen, René Lynge; Pors, Anders; Dreier, Jes

    We present a novel template stripping procedure for fabricating metal films with imprinted nanostructures. The basic idea is to deposit a gold film onto a nano-structured substrate and subsequently strip the film from the substrate surface thereby revealing imprinted nanostructures in the film...... result is a thin gold film with imprinted nano-cavities....

  6. Modeling of Strip Heating Process in Vertical Continuous Annealing Furnace

    Institute of Scientific and Technical Information of China (English)

    WAN Fei; WANG Yong-qin; QIN Shu-ren

    2012-01-01

    The mechanism for heat transfer of radiation is usually adopted to heat strip in vertical continuous annealing furnace. The rate of heat transfer among strip and other objects can be hugely affected by the parameters of strip speed, geometry factors and radiating characteristic of surfaces of strip, radiating tubes and walls of furnace. A model including all parameters is proposed for calculating the heat transfer coefficient, predicting the strip tempera- ture and boundary temperature of strip through analyzing these parameters. The boundary temperature is a important datum and different from average arithmetic value of temperature of strip and temperature in furnace. Also, the model can be used to analyze the relation for temperature of strip and heat transfer coefficient, total heat transfer quantity and heating time. The model is built by using the radiating heat transfer rate, the Newtonrs law of cooling, and lumped system analysis. The results of calculation are compared to the data from production line. The comparisons indicate that the model can well predict the heating process. The model is already applied for process control in pro- duction line. Also, this research will provide a new method for analyzing the radiation heat transfer.

  7. A strip array for spoligotyping of Mycobacterium tuberculosis complex isolates.

    Science.gov (United States)

    Tu, Yiling; Zeng, Xiaohong; Li, Hui; Zheng, Rongrong; Xu, Ye; Li, Qingge

    2016-03-01

    A novel strip array was developed for a nine-spacer spoligotyping scheme of Mycobacterium tuberculosis complex (MTBC). The new method was evaluated using 211 MTBC isolates and the results were fully concordant with the traditional spoligotyping approach. The strip array proved to be rapid and convenient for spoligotyping of MTBC.

  8. Status Quo of China’s Aluminum Sheet & Strip Industry

    Institute of Scientific and Technical Information of China (English)

    2013-01-01

    <正>Aluminum sheet & strip products are one of the major product varieties in the aluminum processing industry, they also provide indis-pensable basic materials for the development of national economy. In recent years, driven by rapid economic growth, China’s investment in aluminum sheet & strip industry continued to

  9. Using Comic Strips as a Book Report Alternative

    Science.gov (United States)

    Reading Teacher, 2012

    2012-01-01

    Comic strips are great to share with parents, younger students, and peers. This article presents an activity where students use a six-paneled comic strip to summarize a story. This activity allows for multiple interpretations and enhances comprehension by drawing attention to story elements.

  10. Using Comic Strips as a Book Report Alternative

    Science.gov (United States)

    Reading Teacher, 2012

    2012-01-01

    Comic strips are great to share with parents, younger students, and peers. This article presents an activity where students use a six-paneled comic strip to summarize a story. This activity allows for multiple interpretations and enhances comprehension by drawing attention to story elements.

  11. Young tourists visiting strip clubs and paying for sex

    DEFF Research Database (Denmark)

    Hesse, Morten; Tutenges, Sébastien

    2011-01-01

    Little is known about young adults’ use of strip clubs and prostitution during their holidays abroad. This study examined this issue with a sample of 1125 Danish tourists between the ages of 16 and 34, and sought data about the frequency with which they paid for sex and attended strip clubs while...

  12. Fabrication of chitosan-magnetite nanocomposite strip for chromium removal

    Science.gov (United States)

    Sureshkumar, Vaishnavi; Kiruba Daniel, S. C. G.; Ruckmani, K.; Sivakumar, M.

    2016-02-01

    Environmental pollution caused by heavy metals is a serious threat. In the present work, removal of chromium was carried out using chitosan-magnetite nanocomposite strip. Magnetite nanoparticles (Fe3O4) were synthesized using chemical co-precipitation method at 80 °C. The nanoparticles were characterized using UV-visible spectroscopy, fourier transform infrared spectroscopy, X-ray diffraction spectrometer, atomic force microscope, dynamic light scattering and vibrating sample magnetometer, which confirm the size, shape, crystalline nature and magnetic behaviour of nanoparticles. Atomic force microscope revealed that the particle size was 15-30 nm and spherical in shape. The magnetite nanoparticles were mixed with chitosan solution to form hybrid nanocomposite. Chitosan strip was casted with and without nanoparticle. The affinity of hybrid nanocomposite for chromium was studied using K2Cr2O7 (potassium dichromate) solution as the heavy metal solution containing Cr(VI) ions. Adsorption tests were carried out using chitosan strip and hybrid nanocomposite strip at different time intervals. Amount of chromium adsorbed by chitosan strip and chitosan-magnetite nanocomposite strip from aqueous solution was evaluated using UV-visible spectroscopy. The results confirm that the heavy metal removal efficiency of chitosan-magnetite nanocomposite strip is 92.33 %, which is higher when compared to chitosan strip, which is 29.39 %.

  13. Determination of residual stresses in roll compacted titanium strips

    CSIR Research Space (South Africa)

    Mothosi, KL

    2017-01-01

    Full Text Available induced during roll compaction of titanium strips were measured for strips of different densities. The different densities were achieved by rolling two different particle size (100 and 325 mesh) titanium powders varying the roll gap (0.1, 0.3 and 0.5 mm...

  14. Tape Stripping Technique for Stratum Corneum Protein Analysis

    DEFF Research Database (Denmark)

    Clausen, Maja-Lisa; Slotved, H.-C.; Krogfelt, Karen Angeliki

    2016-01-01

    The aim of this study was to investigate the amount of protein in stratum corneum in atopic dermatitis (AD) patients and healthy controls, using tape stripping technique. Furthermore, to compare two different methods for protein assessment. Tape stripping was performed in AD patients and healthy ...

  15. SHINE Vacuum Pump Test Verification

    Energy Technology Data Exchange (ETDEWEB)

    Morgan, Gregg A; Peters, Brent

    2013-09-30

    Normetex pumps used world-wide for tritium service are no longer available. DOE and other researchers worldwide have spent significant funds characterizing this pump. Identification of alternate pumps is required for performance and compatibility with tritium gas. Many of the pumps that could be used to meet the functional performance requirements (e.g. pressure and flow conditions) of the Normetex pump have features that include the use of polymers or oils and greases that are not directly compatible with tritium service. This study assembles a test system to determine the flow characteristics for candidate alternate pumps. These tests are critical to the movement of tritium through the SHINE Tritium Purification System (TPS). The purpose of the pump testing is two-fold: (1) obtain baseline vacuum pump characteristics for an alternate (i.e. ''Normetex replacement'') pump intended for use in tritium service; and (2) verify that low pressure hydrogen gas can be transported over distances up to 300 feet by the candidate pumps. Flow rates and nominal system pressures have been identified for the SHINE Mo-99 production process Tritium Purification System (TPS). To minimize the line sizes for the transfer of low pressure tritium from the Neutron Driver Accelerator System (NDAS) to the primary processing systems in the TPS, a ''booster'' pump has been located near the accelerator in the design. A series of pump tests were performed at various configurations using hydrogen gas (no tritium) to ensure that this concept is practical and maintains adequate flow rates and required pressures. This report summarizes the results of the tests that have been performed using various pump configurations. The current design of the Tritium Purification System requires the ''booster'' pump to discharge to or to be backed by another vacuum pump. Since Normetex pumps are no longer manufactured, a commercially available Edwards

  16. 14 CFR 23.991 - Fuel pumps.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel pumps. 23.991 Section 23.991... § 23.991 Fuel pumps. (a) Main pumps. For main pumps, the following apply: (1) For reciprocating engine installations having fuel pumps to supply fuel to the engine, at least one pump for each engine must be...

  17. Sensemaking e o Desenvolvimento de Redes de Relacionamentos de Negócios no Contexto das Empresas de Base Tecnológica

    Directory of Open Access Journals (Sweden)

    Ricardo Sérgio Gomes Vieira

    2012-06-01

    Full Text Available Nas últimas três décadas, questões relativas ao papel e à importância das redes sociais de negócio têm surgido como foco de amplo e acalorado debate entre acadêmicos e profissionais da Administração. Apesar da existência de diversos arcabouços conceituais ligados à Network Theory, o modelo Ator-Atividades-Recursos (AAR desenvolvido pelo IMP-Group tem sido amplamente utilizado numa variedade de contextos organizacionais. Neste artigo, utilizamos o AAR para investigar como oportunidades de negócios são identificadas por dirigentes de empresas de base tecnológica. Nesta pesquisa de natureza qualitativa, básica e de caráter exploratório-descritivo, foram realizadas entrevistas em profundidade. A análise de conteúdo foi adotada como método para interpretar os dados coletados pelas entrevistas. O principal resultado aponta para uma dinâmica coletiva desenvolvida nas redes de relacionamentos de negócios. Além disso, observam-se a importância e o papel do sensemaking em tal atividade. Em linhas gerais, o sensemaking é o processo pelo qual as pessoas geram sentido de suas experiências. Reflexões teóricas sobre os achados são discutidas e implicações para a academia e a prática organizacional, bem como indicações para futuras pesquisas são consideradas. ----- Sensemaking and Business Relationships Network Development in the Context of High-Tech Firms ----- ABSTRACT ----- In the last three decades, issues concerning the role and influence of business social networks have sprung up as the main focus of debate amongst academics and professionals from the Business Area. Although there have been many theoretical backgrounds bounded to Network Theory, the Actor-Activities-Resources model (AAR model developed by IMP-Group has been mostly adopted in a wide array of organizational contexts. Bearing this in mind, the AAR model was used to investigate how business opportunities are identifi ed by the CEOs of High-Tech Firms

  18. Evaluation of anatomy comic strips for further production and applications.

    Science.gov (United States)

    Shin, Dong Sun; Kim, Dae Hyun; Park, Jin Seo; Jang, Hae Gwon; Chung, Min Suk

    2013-09-01

    The corresponding author of the study has been sketching comic strips to explain anatomy in a humorous manner. All the anatomy comic strips, including those in Korean (650 episodes) and English (451 episodes), can be viewed on the homepage (http://anatomy.co.kr). Such comic strips were created with the aim of assisting medical students. However, their impact was unknown, and therefore, we surveyed the students' responses. We noted that anatomy grades were better in the students who read the comic strips. The comics helped the trainees chat with individuals with and without a medical background. The authors also considered comments on the problems with the comic strips and attempted to find solutions. The episodes are being currently used and further produced for educational purposes. To support this effort, the readers' valuable opinions will be continuously collected and assessed.

  19. Evaluation of anatomy comic strips for further production and applications

    Science.gov (United States)

    Shin, Dong Sun; Kim, Dae Hyun; Park, Jin Seo; Jang, Hae Gwon

    2013-01-01

    The corresponding author of the study has been sketching comic strips to explain anatomy in a humorous manner. All the anatomy comic strips, including those in Korean (650 episodes) and English (451 episodes), can be viewed on the homepage (http://anatomy.co.kr). Such comic strips were created with the aim of assisting medical students. However, their impact was unknown, and therefore, we surveyed the students' responses. We noted that anatomy grades were better in the students who read the comic strips. The comics helped the trainees chat with individuals with and without a medical background. The authors also considered comments on the problems with the comic strips and attempted to find solutions. The episodes are being currently used and further produced for educational purposes. To support this effort, the readers' valuable opinions will be continuously collected and assessed. PMID:24179697

  20. Flux avalanches in Nb superconducting shifted strip arrays

    Science.gov (United States)

    Tsuchiya, Y.; Mawatari, Y.; Ibuka, J.; Tada, S.; Pyon, S.; Nagasawa, S.; Hidaka, M.; Maezawa, M.; Tamegai, T.

    2013-09-01

    Flux penetrations into three-dimensional Nb superconducting strip arrays, where two layers of strip arrays are stacked by shifting a half period, are studied using a magneto-optical imaging method. Flux avalanches are observed when the overlap between the top and bottom layers is large even if the width of each strip is well below the threshold value. In addition, anomalous linear avalanches perpendicular to the strip are observed in the shifted strip array when the overlap is very large and the thickness of the superconductor is greater than the penetration depth. We discuss possible origins for the flux avalanches, including linear ones, by considering flux penetration calculated by the Campbell method assuming the Bean model.

  1. Nonlinear optical model for strip plasmonic waveguides

    DEFF Research Database (Denmark)

    Lysenko, Oleg; Bache, Morten; Lavrinenko, Andrei

    2016-01-01

    This paper presents a theoretical model of nonlinear optical properties for strip plasmonic waveguides. The particular waveguides geometry that we investigate contains a gold core, adhesion layers, and silicon dioxide cladding. It is shown that the third-order susceptibility of the gold core...... significantly depends on the layer thickness and has the dominant contribution to the effective third-order susceptibility of the long-range plasmon polariton mode. This results in two nonlinear optical effects in plasmonic waveguides, which we experimentally observed and reported in [Opt. Lett. 41, 317 (2016......)]. The first effect is the nonlinear power saturation of the plasmonic mode, and the second effect is the spectral broadening of the plasmonic mode. Both nonlinear plasmonic effects can be used for practical applications and their appropriate model will be important for further developments in communication...

  2. Synchronization of the CMS Cathode Strip Chambers

    CERN Document Server

    Raknessa, G; Wang, D

    2007-01-01

    The synchronization of the trigger and data acquisition systems for the Cathode Strip Chambers (CSCs) in the Compact Muon Solenoid (CMS) detector at CERN is described. The CSC trigger system is designed to trigger CMS on muons with high efficiency (~99% per chamber) and is able to accurately identify its 25ns proton bunch crossing. To date, asynchronous cosmic ray data have been used to define the protocol and to refine timing algorithms, allowing synchronization to be realized within and between chambers to within ±10 ns. Final synchronization of the CSCs requires timing parameters to be accurate to 2 ns. This goal will be readily achieved from the cosmic ray baseline using data taken with the synchronous beam structure of the Large Hadron Collider.

  3. Digital autoradiography using silicon strip detectors

    Energy Technology Data Exchange (ETDEWEB)

    Overdick, M.

    1998-05-01

    Spatially resolving radiation detection systems operating in real time can be used to acquire autoradiographic images. An overview over alternatives to traditional autoradiography is given and the special features of these filmless methods are discussed. On this basis the design of a system for digital autoradiography using silicon strip detectors is presented. Special emphasis is put on the physical background of the detection process in the semiconductor and on the self-triggering read-out technique. The practical performance of the system is analyzed with respect to energy and spatial resolution. This analysis is complemented by case studies from cell biology (especially electrophoresis), botany and mineralogy. Also the results from a time-resolved autoradiographic experiment are presented. (orig.) 80 refs.

  4. [Obstetrical handbook in comic strip form].

    Science.gov (United States)

    1998-04-01

    An obstetric handbook was created in comic strip form in cooperation with the Ministry of Health in the region of Segou, Mali, for training of traditional midwives living far from community health centers. The drawings illustrate pregnancies at risk that the midwife should be able to identify in order to advise women to stay near the health facility before onset of labor. Drawings indicate pregnancies that are at risk because of the following: small stature, limping as a result of polio or sciatic paralysis, high parity, prior cesarean delivery, heart disease, overly large uterus, or prior stillbirth. Serious complications requiring referral to a health service are also illustrated and include severe anemia, genital bleeding, and signs of toxemia and edema. The midwife should accompany the woman during transport.

  5. Determination of chitosan by cathodic stripping voltammetry.

    Science.gov (United States)

    Lu, Guanghan; Wang, Lirong; Wang, Ruixia; Zeng, Yan; Huang, Xi

    2006-04-01

    A sensitive method for the determination of chitosan (CTS) by cathodic stripping voltammetry is presented. The method exploits a pair of oxidation-reduction peaks of CTS at -0.62 V (vs. SCE) and -0.54 V (vs. SCE), and an enhancement of the peak current of CTS observed in a 0.05 mol l(-1) potassium hydrogenphthalate buffer solution (pH 2.5). The peak current is linear with the concentration of CTS from 5.0 x 10(-7) to 1.5 x 10(-5) g ml(-1), and the detection limit is 1.0 x 10(-7) g ml(-1). We studied the characteristics and the mechanism of the electrode reaction, which proved that this process was diffusion controlled. This method was applied to determine the content of CTS in real samples with satisfactory results.

  6. Optical fiber cable chemical stripping fixture

    Science.gov (United States)

    Kolasinski, John R. (Inventor); Coleman, Alexander M. (Inventor)

    1995-01-01

    An elongated fixture handle member is connected to a fixture body member with both members having interconnecting longitudinal central axial bores for the passage of an optical cable therethrough. The axial bore of the fixture body member, however, terminates in a shoulder stop for the outer end of a jacket of the optical cable covering both an optical fiber and a coating therefor, with an axial bore of reduced diameter continuing from the shoulder stop forward for a predetermined desired length to the outer end of the fixture body member. A subsequent insertion of the fixture body member including the above optical fiber elements into a chemical stripping solution results in a softening of the exposed external coating thereat which permits easy removal thereof from the optical fiber while leaving a desired length coated fiber intact within the fixture body member.

  7. Pocket pumped image analysis

    Energy Technology Data Exchange (ETDEWEB)

    Kotov, I.V., E-mail: kotov@bnl.gov [Brookhaven National Laboratory, Upton, NY 11973 (United States); O' Connor, P. [Brookhaven National Laboratory, Upton, NY 11973 (United States); Murray, N. [Centre for Electronic Imaging, Open University, Milton Keynes, MK7 6AA (United Kingdom)

    2015-07-01

    The pocket pumping technique is used to detect small electron trap sites. These traps, if present, degrade CCD charge transfer efficiency. To reveal traps in the active area, a CCD is illuminated with a flat field and, before image is read out, accumulated charges are moved back and forth number of times in parallel direction. As charges are moved over a trap, an electron is removed from the original pocket and re-emitted in the following pocket. As process repeats one pocket gets depleted and the neighboring pocket gets excess of charges. As a result a “dipole” signal appears on the otherwise flat background level. The amplitude of the dipole signal depends on the trap pumping efficiency. This paper is focused on trap identification technique and particularly on new methods developed for this purpose. The sensor with bad segments was deliberately chosen for algorithms development and to demonstrate sensitivity and power of new methods in uncovering sensor defects.

  8. Wavy tube heat pumping

    Energy Technology Data Exchange (ETDEWEB)

    Haldeman, C. W.

    1985-12-03

    A PVC conduit about 4'' in diameter and a little more than 40 feet long is adapted for being seated in a hole in the earth and surrounds a coaxial copper tube along its length that carries Freon between a heat pump and a distributor at the bottom. A number of wavy conducting tubes located between the central conducting tube and the wall of the conduit interconnect the distributor with a Freon distributor at the top arranged for connection to the heat pump. The wavy conducting tubing is made by passing straight soft copper tubing between a pair of like opposed meshing gears each having four convex points in space quadrature separated by four convex recesses with the radius of curvature of each point slightly less than that of each concave recess.

  9. Advanced heat pump cycle

    Energy Technology Data Exchange (ETDEWEB)

    Groll, E.A.; Radermacher, R.

    1993-07-01

    The desorption and absorption process of a vapor compression heat pump with a solution circuit (VCHSC) proceeds at gliding temperature intervals, which can be adjusted over a wide range. In case that the gliding temperature intervals in the desorber and the absorber overlap, a modification of the VCHSC employing a desorber/absorber heat exchange (DAHX) can be introduced, which results in an extreme reduction of the pressure ratio. Although the DAHX-cycle has features of a two-stage cycle, it still requires only one solution pump, one separator and one compressor. Such a cycle for the working pair ammonia/water is built in the Energy Laboratory of the Center for Environmental Energy Engineering at the University of Maryland. The experimental results obtained with the research plant are discussed and compared to those calculated with a simulation program. The possible temperature lift between heat source and heat sink depending on the achievable COP are presented.

  10. Inertial microfluidic pump

    Science.gov (United States)

    Kornilovitch, Pavel; Govyadinov, Alexander; Markel, David; Torniainen, Erik

    2015-11-01

    The inertial pump is powered by a microheater positioned near one end of a fluidic microchannel. As the microheater explosively boils the surrounding fluid, a vapor bubble expands and then collapses asymmetrically, resulting in net flow. Such devices become an effective means of transporting fluids at microscale. They have no moving parts and can be manufactured in large numbers using standard batch fabrication processes. In this presentation, physical principles behind pump operation are described, in particular the role of reservoirs in dissipating mechanical momentum and the expansion-collapse asymmetry. An effective one-dimensional dynamic model is formulated and solved. The model is compared with full three-dimensional CFD simulations and available experimental data. Potential applications of inertial micropumps are described.

  11. Technology assessment heat pumps

    Energy Technology Data Exchange (ETDEWEB)

    Rudolph, R.; Purper, G. (Battelle-Institut e.V., Frankfurt am Main (Germany, F.R.))

    Technology assessment for an increased application of heat pumps is carried out in four areas: Effects in the economics area, i.e. effects on the economic goals which are defined in the Stability Law, on the goals of the power supply policy which result from the energy programme and its projections, and on the economic structure as a whole. The whole range of social problems concerning the use of heat pumps, i.e. the questions which social groups are affected, how they react, and what consequences are they expected to have on energy conservation as an object of social policy. Consequences in the governmental and administrative sectors, i.e. effects on legislation, administration and government budgets. Effects on the ecological systems; of prime interest in this context are the utilisation of environmental energy, changes in the heat balance, and emmission of pollutants.

  12. Reflexão sobre a missão desafiadora do constructo marca-país na área de negócios internacionais

    Directory of Open Access Journals (Sweden)

    Fabiana Gondim Mariutti

    2015-12-01

    Full Text Available A importância de uma marca-país promovida estrategicamente é um dos propósitos fundamentais em negócios internacionais. Cada nação tenta transmitir seus atributos internacionalmente - não apenas seus produtos e serviços, mas também a sua imagem geral. Além disso, pesquisas sobre o construto de marca-país estão sendo realizadas continuamente em institutos governamentais e ambientes acadêmicos e corporativos. As nações precisam se promover estrategicamente se desejam serem percebidas. Baseada nesta premissa, o objetivo desta reflexão teórica é abordar este constructo para delinear o desenvolvimento desta linha de pesquisa e propor um arcabouço teórica para pesquisas futuras. Este artigo também colabora para a compreensão da missão desafiadora do constructo marca-país, cujas estratégias podem ser aplicadas na prática e na teoria da disciplina. Este estudo conceptual complementa o estado-da-arte sobre as complexidades do construto de marca-país através da compreensão das filosofias-chave sobre o tema depois de traçar a sua evolução. A combinação de resultados ofereceu suporte para a elaboração de um quadro conceptual relacionado com as principais complexidades do construto de marca-país, os quais são os seguintes: natureza multifacetada; variedade de muitos grupos de stakeholders; envolvimento do governo; oportunidades interdisciplinares e multidisciplinares e potenciais modelos para marca-país. Assim, o artigo considera que as estratégias dinâmicas e funcionais de branding para uma marca-país proporcionam autenticidade às nações no cenário internacional de negócios e ao fazê-lo - esta missão desafiadora da marca-país beneficia a economia e o comércio internacional; desenvolve as relações diplomáticas e os avanços de pesquisa sobre marketing internacional; fomenta programas de intercâmbios acadêmicos e de ensino; por fim, avança na sustentabilidade nacional e global.

  13. Um negócio da China: o discurso do guānxì nas articulações no âmbito organizacional

    Directory of Open Access Journals (Sweden)

    Osíris Luís da Cunha Fernandes

    Full Text Available Este estudo explora o guānxì como discurso organizacional vigente na cultura de negócios nas organizações chinesas a partir da lógica da equivalência e da lógica da diferença propostas por Ernesto Laclau e Chantal Mouffe. O guānxì consiste em um relacionamento interpessoal e na criação de conhecimento colaborativo que envolve um saber tácito, orientado para o futuro, complexo que opera em contexto específico. Em uma perspectiva pós-estruturalista aplicada às organizações, utilizamos a análise de discurso como método que permite pôr em prática o papel da linguagem na condição de eixo de compreensão de processos sociais, como acontece com o guānxì. Analisamos 3 entrevistas em profundidade realizadas com chief executive officers (CEOs chineses e 32 reportagens relacionadas à prática do guānxì em organizações do setor terciário, publicadas em 2 dos maiores diários digitais da China. Com isso, nosso objetivo foi identificar a forma como esse fenômeno tem sido apropriado como discurso no âmbito organizacional a partir da lógica da equivalência e da lógica da diferença. Constatamos que as organizações chinesas utilizam o guānxì para obterem acesso preferencial a atores estratégicos que têm informações e recursos demandados nos processos negociais, com vista a obterem vantagens competitivas. Por outro lado, o sucesso dos negócios envolvendo essas organizações depende de uma identificação mútua entre seus líderes, baseada na confiança e credibilidade estabelecidas nas articulações.

  14. A importância da inovação para a gestão integrada do negócio e sua competitividade

    Directory of Open Access Journals (Sweden)

    Gilberto Bacarim

    2009-01-01

    Full Text Available A inovação é a prática da idéia, fruto da criatividade. As experiências de empresas reconhecidamente inovadoras são lições importantes sobre a contribuição da inovação para a gestão do negócio: a liberdade de pensar e agir com responsabilidade dentro de equipes multidisciplinares trabalhando em projetos com horizontes de retorno de curto, médio e longo prazos e capazes de aliar, de forma competente, experiência e visão. Dentro de uma perspectiva histórica, as empresas têm descoberto que não faz sentido disputas internas em torno de projetos. Esses, na sua essência, devem trazer uma contribuição mercadológica para o negócio, em termos de produto, distribuição, comunicação com o mercado ou serviços. Devem refletir a inovação contínua, agregando valor e melhorando o grau de competitividade da empresa no mercado. Palavras-chave: inovação, marketing integrado, empresas inovadoras. Abstract Innovation is the practice of an idea produced by creativity. The experience of companies aknowledged as innovators are important lessons on the contribution of innovation for business management: the freedom to think and act with responsibility within multi-disciplinary teams working with short, medium and long term projects putting side by side, in a competent way, experience and vision. From a historical perspective, companies have discovered that internal issues about projects make no sense, These must give a marketing contribution to the business either in terms of product, distribution, communication or services. They must reflect the continuous innovation, adding value and increasing the degree of competitiveness of the company in the market. Key words: innovation, integrated marketing, innovating companies.

  15. Photo-dynamics of the BLUF domain containing soluble adenylate cyclase (nPAC) from the amoeboflagellate Naegleria gruberi NEG-M strain

    Energy Technology Data Exchange (ETDEWEB)

    Penzkofer, A., E-mail: alfons.penzkofer@physik.uni-regensburg.de [Fakultaet fuer Physik, Universitaet Regensburg, Universitaetsstrasse 31, D-93053 Regensburg (Germany); Stierl, M.; Hegemann, P. [Institut fuer Biologie/Experimentelle Biophysik, Humboldt Universitaet zu Berlin, Invalidenstrasse 42, D-10115 Berlin (Germany); Kateriya, Suneel [Department of Biochemistry, University of Delhi South Campus, Benito Juarez Road, New Delhi 110021 (India)

    2011-08-25

    Graphical abstract: The photoactivated adenylyl cyclase (nPAC) from Naegleria gruberi was expressed heterologously in Escherichia coli and its photo-cycling dynamics was studied by optical absorption and fluorescence spectroscopy. Highlights: {yields} Photo-activated adenylyl cyclase (nPAC) from Naegleria gruberi NEG-M was expressed. {yields} Photodynamics of BLUF domain in BLUF sensor - cyclase actuator protein was studied. {yields} Photo-excitation caused BLUF photo-cycling and permanent protein re-conformation. {yields} Re-conformed protein enabled photo-induced flavin reduction by proton transfer. {yields} Fluorescence of flavin in dark- and light-adapted state of nPAC was characterized. - Abstract: The amoeboflagellate Naegleria gruberi NEG-M comprises a BLUF (blue light sensor using flavin) regulated adenylate cyclase (nPAC). The nPAC gene was expressed heterologously in Escherichia coli and the photo-dynamics of the nPAC protein was studied by optical absorption and fluorescence spectroscopy. Blue-light exposure of nPAC caused a typical BLUF-type photo-cycle behavior (spectral absorption red-shift, fluorescence quenching, absorption and fluorescence recovery in the dark). Additionally, time-delayed reversible photo-induced one-electron reduction of fully oxidized flavin (Fl{sub ox}) to semi-reduced flavin (FlH{sup {center_dot}}) occurred. Furthermore, photo-excitation of FlH{sup {center_dot}} caused irreversible electron transfer to fully reduced anionic flavin (FlH{sup -}). A photo-induced electron transfer from Tyr or Trp to flavin (Tyr{sup {center_dot}+}-Fl{sup {center_dot}-} or Trp{sup {center_dot}+}-Fl{sup {center_dot}-} radical ion-pair formation) is thought to cause H-bond restructuring responsible for BLUF-type photo-cycling and permanent protein re-conformation enabling photo-induced flavin reduction by proton transfer. Some photo-degradation of Fl{sub ox} to lumichrome was observed. A model of the photo-dynamics of nPAC is developed.

  16. Streptococcus pneumoniae carriage in the Gaza strip.

    Directory of Open Access Journals (Sweden)

    Gili Regev-Yochay

    Full Text Available BACKGROUND: Pneumococcal infections cause major morbidity and mortality in developing countries. We report the epidemiology of S. pneumoniae carriage in a developing region, the Gaza strip, and evaluate the theoretical coverage of carriage strains by pneumococcal conjugate vaccines (PCVs. METHODOLOGY: In 2009 we conducted a cross-sectional survey of S. pneumoniae carriage in healthy children and their parents, living throughout the Gaza strip. Data were collected and nasopharyngeal swabs were obtained. Antibiotic susceptibilities were determined by Vitek-2 and serotypes by the Quellung reaction. PRINCIPAL FINDINGS: S. pneumoniae carriage was detected in 189/379 (50% of children and 30/376 (8% of parents. Carriage prevalence was highest in children <6 months of age (63%. Significant predictors for child carriage were number of household members and DCC attendance. The proportion of pediatric and adults isolates with serotypes included in PCV7 were 32% and 20% respectively, and 46% and 33% in PCV13 respectively. The most prominent non-vaccine serotypes (NVT were 35B, 15B/C and 23B. Penicillin-nonsusceptible strains were carried by 70% of carriers, penicillin-resistant strains (PRSP by 13% and Multi-drug-resistant (MDR by 30%. Of all PRSP isolates 54% belonged to serotypes included in PCV7 and 71% in the PCV13. Similarly, 59% and 73% of MDR-SP isolates, would theoretically be covered by PCV7 and PCV13, respectively. CONCLUSIONS: This study demonstrates that, PCV13-included strains were carried by 46% and 33% of pediatric and adult subjects respectively. In the absence of definitive data regarding the virulence of the NVT strains, it is difficult to predict the effect of PCVs on IPD in this region.

  17. Hydrodynamics of Pumps

    OpenAIRE

    Brennen, Christopher Earls

    1994-01-01

    The subject of this monograph is the fluid dynamics of liquid turbomachines, particularly pumps. Rather than attempt a general treatise on turbomachines, we shall focus attention on those special problems and design issues associated with the flow of liquid through a rotating machine. There are two characteristics of a liquid that lead to these special problems, and cause a significantly different set of concerns than would occur in, say, a gas turbine. These are the potential for cavitation ...

  18. Pioneering Heat Pump Project

    Energy Technology Data Exchange (ETDEWEB)

    Aschliman, Dave [Indiana Inst. of Technology, Inc., Fort Wayne, IN (United States); Lubbehusen, Mike [Indiana Inst. of Technology, Inc., Fort Wayne, IN (United States)

    2015-06-30

    This project was initiated at a time when ground coupled heat pump systems in this region were limited in size and quantity. There were economic pressures with costs for natural gas and electric utilities that had many organizations considering ground coupled heat pumps; The research has added to the understanding of how ground temperatures fluctuate seasonally and how this affects the performance and operation of the heat pumps. This was done by using a series of temperature sensors buried within the middle of one of the vertical bore fields with sensors located at various depths below grade. Trending of the data showed that there is a lag in ground temperature with respect to air temperatures in the shoulder months, however as full cooling and heating season arrives, the heat rejection and heat extraction from the ground has a significant effect on the ground temps; Additionally it is better understood that while a large community geothermal bore field serving multiple buildings does provide a convenient central plant to use, it introduces complexity of not being able to easily model and predict how each building will contribute to the loads in real time. Additional controllers and programming were added to provide more insight into this real time load profile and allow for intelligent shedding of load via a dry cooler during cool nights in lieu of rejecting to the ground loop. This serves as a means to ‘condition’ the ground loop and mitigate thermal creep of the field, as is typically observed; and It has been observed when compared to traditional heating and cooling equipment, there is still a cost premium to use ground source heat pumps that is driven mostly by the cost for vertical bore holes. Horizontal loop systems are less costly to install, but do not perform as well in this climate zone for heating mode

  19. Positive displacement rotary pump

    Science.gov (United States)

    Moody, Paul E.

    1994-04-01

    An eccentric drive rotates inside a ring that is hinged to a plate and an elastomeric curtain is wrapped around the ring and across an articulated plate. The curtain moves along a cylindrical wall inside the pump cavity to move fluid from an inlet to an outlet end of the chamber. Two or more chambers can be coupled in series or in parallel with one another.

  20. Nonazeotropic Heat Pump

    Science.gov (United States)

    Ealker, David H.; Deming, Glenn

    1991-01-01

    Heat pump collects heat from water circulating in heat-rejection loop, raises temperature of collected heat, and transfers collected heat to water in separate pipe. Includes sealed motor/compressor with cooling coils, evaporator, and condenser, all mounted in outer housing. Gradients of temperature in evaporator and condenser increase heat-transfer efficiency of vapor-compression cycle. Intended to recover relatively-low-temperature waste heat and use it to make hot water.

  1. Nonazeotropic Heat Pump

    Science.gov (United States)

    Ealker, David H.; Deming, Glenn

    1991-01-01

    Heat pump collects heat from water circulating in heat-rejection loop, raises temperature of collected heat, and transfers collected heat to water in separate pipe. Includes sealed motor/compressor with cooling coils, evaporator, and condenser, all mounted in outer housing. Gradients of temperature in evaporator and condenser increase heat-transfer efficiency of vapor-compression cycle. Intended to recover relatively-low-temperature waste heat and use it to make hot water.

  2. Introduction to Pump Rotordynamics

    Science.gov (United States)

    2006-11-01

    RTO-EN-AVT-143 9 - 1 Introduction to Pump Rotordynamics Luis San Andrés Mast-Childs Tribology Professor Turbomachinery Laboratory Texas A... rotordynamics of turbomachinery, excessive vibration and instability. The acceptable performance of a turbomachine depends on the adequate design and operation...on rotordynamics . The basic equations for the modeling of linear rotor-bearing systems are given along with an example for the rotordynamics of a

  3. Application of WLS strips for position determination in Strip PET tomograph based on plastic scintillators

    CERN Document Server

    Smyrski, J; Bednarski, T; Białas, P; Czerwiński, E; Kapłon, Ł; Kochanowski, A; Korcyl, G; Kowal, J; Kowalski, P; Kozik, T; Krzemień, W; Molenda, M; Niedźwiecki, Sz; Pałka, M; Pawlik, M; Raczyński, L; Rudy, Z; Salabura, P; Sharma, N G; Silarski, M; Słomski, A; Strzelecki, A; Wiślicki, W; Zieliński, M; Zoń, N

    2013-01-01

    A method of determination of a gamma quantum absorption point in a plastic scintillator block using a matrix of wavelength-shifting (WLS) strips is proposed. Application of this method for improvement of position resolution in newly proposed PET detectors based on plastic scintillators is presented. The method enables to reduce parallax errors in reconstruction of images which occurs in the presently used Positron Emission Tomography scanners.

  4. Electrocentrifugal pumping; Bombeo electrocentrifugo

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez Perez, Guillermo; Medellin Otero, Hector [Instituto Mexicano del Peroleo (Mexico)

    1996-07-01

    The exploitation of isolated oil deposits, in losing their own energy, enter a phase of secondary recovery. One of the technologies of new development in Mexico is the one of electrocentrifugal pumping , which consists of introducing the motor-pump as an integral part of the production pipe down to the well bottom and pumping directly up to central complexes, from where it is sent inland. In the present paper is intended to explain what this type of secondary recovery consists of. [Spanish] La explotacion de yacimientos aislados de petroleo, al perder su energia propia, entran en una fase de recuperacion secundaria. Una de las tecnologias de nuevo desarrollo en Mexico es la de bombeo electrocentrifugo, la cual consiste en introducir la motobomba como parte integral de la tuberia de produccion hasta el fondo del pozo y bombearlo directamente hasta los complejos centrales, de donde se envia a tierra. En el presente trabajo se pretende explicar en que consiste este tipo de recuperacion secundaria.

  5. Stirling Engine Heat Pump

    Science.gov (United States)

    Kagawa, Noboru

    Recent advances in the feasibility studies related to the Stirling engines and Stirling engine heat pumps which have been considered attractive due to their promising role in helping to solve the global environmental and energy problems,are reviewed. This article begins to describe the brief history of the Stirling engines and theoretical thermodynamic analysis of the Stirling cycle in order to understand several advantages on the Stirling engine. Furthermore,they could throw light on our question why the dream engines had not been promoted to practical applications during two hundred years. The present review shows that the Stirling engines with several unique advantages including 30 to 40% thermal efficiency and preferable exhaust characteristics,had been designed and constructed by recent tackling for the development of the advanced automobile and other applications using them. Based on the current state of art,it is being provided to push the Stirling engines combined with heat pumps based on the reversed Rankine cycle to the market. At present,however, many problems, especially for the durability, cost, and delicate engine parts must be enforced to solve. In addition,there are some possibilities which can increase the attractiveness of the Stirling engines and heat pumps. The review closes with suggestions for further research.

  6. A Magnetically Coupled Cryogenic Pump

    Science.gov (United States)

    Hatfield, Walter; Jumper, Kevin

    2011-01-01

    Historically, cryogenic pumps used for propellant loading at Kennedy Space Center (KSC) and other NASA Centers have a bellows mechanical seal and oil bath ball bearings, both of which can be problematic and require high maintenance. Because of the extremely low temperatures, the mechanical seals are made of special materials and design, have wearing surfaces, are subject to improper installation, and commonly are a potential leak path. The ball bearings are non-precision bearings [ABEC-1 (Annular Bearing Engineering Council)] and are lubricated using LOX compatible oil. This oil is compatible with the propellant to prevent explosions, but does not have good lubricating properties. Due to the poor lubricity, it has been a goal of the KSC cryogenics community for the last 15 years to develop a magnetically coupled pump, which would eliminate these two potential issues. A number of projects have been attempted, but none of the pumps was a success. An off-the-shelf magnetically coupled pump (typically used with corrosive fluids) was procured that has been used for hypergolic service at KSC. The KSC Cryogenics Test Lab (CTL) operated the pump in cryogenic LN2 as received to determine a baseline for modifications required. The pump bushing, bearings, and thrust rings failed, and the pump would not flow liquid (this is a typical failure mode that was experienced in the previous attempts). Using the knowledge gained over the years designing and building cryogenic pumps, the CTL determined alternative materials that would be suitable for use under the pump design conditions. The CTL procured alternative materials for the bearings (bronze, aluminum bronze, and glass filled PTFE) and machined new bearing bushings, sleeves, and thrust rings. The designed clearances among the bushings, sleeves, thrust rings, case, and case cover were altered once again using experience gained from previous cryogenic pump rebuilds and designs. The alternative material parts were assembled into

  7. O professor de inglês para negócios: reflexos de uma identidade em construção = The business english teacher: reflexes of an identity under construction

    Directory of Open Access Journals (Sweden)

    Sa, Elisa Mattos de

    2011-01-01

    Full Text Available Este artigo tem como principal objetivo refletir sobre a identidade do professor de inglês para negócios, considerando-se a identidade como um processo construído pelas relações que os sujeitos estabelecem entre si em situações de interação social (Moita Lopes, 2003; Hall, 2000; Rajagopalan, 1998, pela linguagem, lugar onde o ser humano se constitui como sujeito e constrói sua realidade (Bakhtin, 1981. Pensado qualitativamente, este trabalho apresenta excertos de uma entrevista semi-estruturada baseada no modelo de Bereckzky (2009, nos quais pode-se perceber reflexos identitários de um professor de inglês para negócios, identidade essa negociada e renegociada nas relações que o professor estabelece com seus alunos e suas práticas de ensino

  8. Teoria do caos e gestão da informação: uma integração na complexidade dos negócios e dos sistemas de informação

    Directory of Open Access Journals (Sweden)

    Luiz Henrique Cardoso

    Full Text Available É abordado o planejamento de sistemas de informação, em seu aspecto teórico, sob a ótica da Teoria do Caos e da Complexidade. Descreve as características dos sistemas físicos, a visão da ciência como sistema fechado e a visão da ciência como sistema aberto. Discute ainda a gestão da informação, tanto frente à complexidade dos sistemas de informação, quanto em suas correlações com o mundo dos negócios, enfatizando a necessidade do profissional da informação de estar apto para planejar o seu trabalho diante do cenário complexo dos negócios.

  9. New Concept of Cultivation Using Limited Strip-Tillage with Strip Shallow Irrigation

    Directory of Open Access Journals (Sweden)

    Yazid Ismi Intara

    2014-04-01

    Full Text Available Normal 0 false false false IN X-NONE X-NONE Dry land is one of land resources which potentially used for food crop cultivation, especially in the areas which have light to medium technical obstacles. The development of technology to improve soil quality in marginal lands to be productive lands is still widely open for agricultural development in Indonesia. Rooting medium quality can be improved by changing soil tillage method and observing the proper crop irrigation technology. It can be the solution for crop cultivation in clay loam soil. This study aimed to obtain water movement model in a minimally-tilled clay soil with strip shallow irrigation. The concept is limited soil-tillage with strip shallow irrigation method, water supply technique, and crop water requirement. Method used in this study includes developing water movement model (software development in a minimally-tilled clay soil with subsurface irrigation. In the final stages, research also conducted water movement analysis testing apparatus in the laboratory, field validation of the subsurface irrigation performance, and cultivation technique testing to chili pepper growth (Capsicum annuumL.. The development of water movement simulation on a limited strip-tillage with subsurface irrigation uses the concept to quantify the amount of water in the soil. The analysis of movement pattern was demonstrated on contour patterns. It showed that the wetting process can reach depth zone – 5 cm to the rooting zone. It was an important discovery on the development of minimum stripe tillage soil with subsurface irrigation. Specifically, it can be concluded that: the result of fitting by eyes to diffusivity graphic and water content obtained the required parameter values for soil physical properties. It was then simulated on horizontal water movement model on a minimum strip-tillage with strip shallow irrigation /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso

  10. Supercritical waste oxidation pump investigation

    Energy Technology Data Exchange (ETDEWEB)

    Thurston, G.; Garcia, K.

    1993-02-01

    This report investigates the pumping techniques and pumping equipment that would be appropriate for a 5,000 gallon per day supercritical water oxidation waste disposal facility. The pumps must boost water, waste, and additives from atmospheric pressure to approximately 27.6 MPa (4,000 psia). The required flow ranges from 10 gpm to less than 0.1 gpm. For the higher flows, many commercial piston pumps are available. These pumps have packing and check-valves that will require periodic maintenance; probably at 2 to 6 month intervals. Several commercial diaphragm pumps were also discovered that could pump the higher flow rates. Diaphragm pumps have the advantage of not requiring dynamic seals. For the lower flows associated with the waste and additive materials, commercial diaphragm pumps. are available. Difficult to pump materials that are sticky, radioactive, or contain solids, could be injected with an accumulator using an inert gas as the driving mechanism. The information presented in this report serves as a spring board for trade studies and the development of equipment specifications.

  11. Implicazioni della regolazione dei mercati dei derivati sulle materie prime negli USA e nell’Unione Europea ((Implications of regulating commodity derivatives markets in the USA and EU

    Directory of Open Access Journals (Sweden)

    Jayati Ghosh

    2012-01-01

    Full Text Available The argument for effective financial regulation to curb financial activity and associated volatility in primary commodity markets is now more compelling than ever, in the context of the renewed increase in food prices. However, as in much other financial regulation, the devil is in the detail. This paper considers recent patterns in global food markets and discusses some of the implications of recent moves to regulate financial activity in commodity futures markets in the US and the EU. Specific regulatory issues are considered and alternative strategies are considered.   L'argomento per un efficace regolamentazione finanziaria per frenare l'attività finanziaria e la volatilità associata nei mercati delle materie primarie è ora più avvincente che mai, nel contesto del nuovo aumento dei prezzi alimentari. Tuttavia, come in gran parte degli altri regolamenti finanziari, il diavolo si nasconde nei dettagli. Questo lavoro considera i recenti modelli nei mercati alimentari mondiali e discute come alcune delle implicazioni di mosse recenti regolano l'attività finanziaria nei futuri mercati di materie prime negli Stati Uniti e l'Unione europea. Specifici problemi di regolamentazione e strategie alternative sono considerati.  JEL Codes: F02, F14, G18, N50Keywords: Finance, Commodities, Food

  12. A crise dos negócios do diamante e as respostas dos homens de fortuna no Alto Jequitinhonha, décadas de 1870-1890

    Directory of Open Access Journals (Sweden)

    Marcos Lobato Martins

    2008-09-01

    Full Text Available Este trabalho aborda a crise da mineração em Diamantina no período 1870-1890 e os impactos que ela gerou sobre os negócios dos grandes mineradores e negociantes de diamante. A ênfase recai sobre a trajetória regional da indústria de lapidação, que representou tentativa de agregar valor às gemas extraídas nas lavras do Alto Jequitinhonha. Também são analisados os investimentos que os homens de fortuna fizeram em firmas comerciais e industriais (principalmente fábricas de tecidos e os projetos de desenvolvimento regional elaborados por empresários diamantinenses neste período. O trabalho utiliza fontes locais diversas como inventários, processos de falências, contratos, jornais, discursos e panfletos políticos.This paper examines the mining crisis in Diamantina between 1870 and 1890 and the consequences it produced on the great miners and diamond dealer's business. It enphazises the regional trajectory of the lapidary industry, that represented an attempt to aggregate value to the gemstones mined in the Upper-Jequitinhonha. The paper also analyses the investments carried out by the businessmen in commercial and industrial partnerships (especially fabric factories, as well as the regional development projects fostered by Diamantina's entrepreneurs in the period. This paper utilizes several local sources like inventories, liquidations processes, contracts, newspapers, political speeches and political pamphlets.

  13. Photo-dynamics of the lyophilized photo-activated adenylate cyclase NgPAC2 from the amoeboflagellate Naegleria gruberi NEG-M strain

    Energy Technology Data Exchange (ETDEWEB)

    Penzkofer, A., E-mail: alfons.penzkofer@physik.uni-regensburg.de [Fakultät für Physik, Universität Regensburg, Universitätsstrasse 31, D-93053 Regensburg (Germany); Tanwar, M.; Veetil, S.K.; Kateriya, S. [Department of Biochemistry, University of Delhi South Campus, Benito Juarez Road, New Delhi 110021 (India); Stierl, M.; Hegemann, P. [Institut für Biologie/Experimentelle Biophysik, Humboldt Universität zu Berlin, Invalidenstrasse 42, D-10115 Berlin (Germany)

    2013-09-23

    Highlights: • Lyophilizing of NgPAC2 from Naegleria gruberi caused loss of BLUF domain activity. • Photo-induced tyrosine to flavin electron transfer in lyophilized NgPAC2. • Photo-induced Tyr–Tyr cross-linking to o,o′-dityrosine in lyophilized NgPAC2. • Photo-induced partial flavin cofactor reduction in lyophilized NgPAC2. • Two NgPAC2 conformations with fast and slow photo-induced electron transfer. - Abstract: The absorption and emission spectroscopic behavior of lyophilized photo-activated adenylate cyclase NgPAC2 from the amoeboflagellate Naegleria gruberi NEG-M strain consisting of a BLUF domain (BLUF = Blue Light sensor Using Flavin) and a cyclase homology domain was studied in the dark, during blue-light exposure and after blue-light exposure at a temperature of 4 °C. The BLUF domain photo-cycle dynamics observed for snap-frozen NgPAC2 was lost by lyophilization (no signaling state formation with flavin absorption red-shift). Instead, blue-light photo-excitation of lyophilized NgPAC2 caused sterically restricted Tyr–Tyr cross-linking (o,o′-ditysosine formation) and partial flavin cofactor reduction.

  14. A superação do paradigma clássico do negócio jurídico: liberalismo e republicanismo

    Directory of Open Access Journals (Sweden)

    Marcos Antônio Striquer Soares

    2017-03-01

    Full Text Available Tenta-se resolver em qual modelo de liberdade, republicana ou liberal, o direito contratual brasileiro se baseia. Utilizou-se o método de revisão literária, pautado na construção teórico-científica fazendo um recorte no modelo filosófico da liberdade e no direito contratual pátrio. Para melhor compreensão, o artigo trabalha com a superação do paradigma do negócio jurídico clássico pelo moderno. No terceiro capítulo o artigo analisa cada paradigma fazendo uma ligação da concepção clássica e moderna com a liberal e republicana de liberdade. Assim, ficou evidenciado que o direito contratual do ordenamento jurídico brasileiro possuía como fundamento no paradigma clássico uma visão liberal de liberdade, porém com a superação do paradigma clássico pelo moderno percebe-se que é possível justificar a tutela dos direitos estatuídos pela Constituição Federal e absorvidos pelo direito civil brasileiro na perspectiva liberal tanto quanto na republicana, conforme demonstrado no trabalho.

  15. Modification of pure oxygen absorption equipment for concurrent stripping of carbon dioxide

    Science.gov (United States)

    Watten, B.J.; Sibrell, P.L.; Montgomery, G.A.; Tsukuda, S.M.

    2004-01-01

    The high solubility of carbon dioxide precludes significant desorption within commercial oxygen absorption equipment. This operating characteristic of the equipment limits its application in recirculating water culture systems despite its ability to significantly increase allowable fish loading rates (kg/(L min)). Carbon dioxide (DC) is typically removed by air stripping. This process requires a significant energy input for forced air movement, air heating in cold climates and water pumping. We developed a modification for a spray tower that provides for carbon dioxide desorption as well as oxygen absorption. Elimination of the air-stripping step reduces pumping costs while allowing dissolved nitrogen to drop below saturation concentrations. This latter response provides for an improvement in oxygen absorption efficiency within the spray tower. DC desorption is achieved by directing head-space gases from the spray tower (O2, N2, CO2) through a sealed packed tower scrubber receiving a 2 N NaOH solution. Carbon dioxide is selectively removed from the gas stream, by chemical reaction, forming the product Na 2CO3. Scrubber off-gas, lean with regard to carbon dioxide but still rich with oxygen, is redirected through the spray tower for further stripping of DC and absorption of oxygen. Make-up NaOH is metered into the scrubbing solution sump on an as needed basis as directed by a feedback control loop programmed to maintain a scrubbing solution pH of 11.4-11.8. The spent NaOH solution is collected, then regenerated for reuse, in a batch process that requires relatively inexpensive hydrated lime (Ca(OH)2). A by-product of the regeneration step is an alkaline filter cake, which may have use in bio-solids stabilization. Given the enhanced gas transfer rates possible with chemical reaction, the required NaOH solution flow rate through the scrubber represents a fraction of the spray tower water flow rate. Further, isolation of the water being treated from the atmosphere (1

  16. Direct pumping of four levels lasing materials

    Science.gov (United States)

    Goldring, Sharone; Lavi, Raphael; Tal, Alon; Jackel, Steven M.; Lebiush, Eyal; Tzuk, Yitshak; Azoulay, Ehud

    2003-06-01

    Heat generation and laser performance were studied in Nd:YAG oscillators pumped with a Ti:Sapphire laser in two regimes: band pumping at 802nm and direct pumping at 885nm. Slope efficiencies of 52% and 57%, when pumped at 802nm and 885nm, were obtained, respectively. Heat per unit laser output was found to be 27% lower when pumped at 885nm (direct pumping regime) as compared to traditional band pumping around 808nm.

  17. Water Modeling of Twin-Roll Strip Casting

    Institute of Scientific and Technical Information of China (English)

    WANG Bo; ZHANG Jie-yu; FAN Jun-fei; ZHAO Shun-li; FANG Yuan; AN Sheng-li

    2006-01-01

    Twin-roll strip casting is regarded as a prospective technology of near net shape continuous casting. The fluid flow field and level fluctuation in the pool have a strong influence not only on composition and temperature homogeneity of pool, but also on the strip quality. A 1∶1 water model of a twin-roll strip caster was set up based on the criteria of Froude number and Reynold number similarity. The level fluctuation was measured. The influence of pool depth, casting speed and feeding system configuration on level fluctuation in the pool was studied. The experimental results provided a basis for the optimization of feeding system and process parameters.

  18. Improvement of Prediction Method for Strip Coiling Temperature

    Institute of Scientific and Technical Information of China (English)

    YU Qing-bo; WANG Zhao-dong; WANG Zhe-ying; LIU Xiang-hua; WANG Guo-dong

    2003-01-01

    In order to improve the control precision of strip coiling temperature for hot strip mill, the BP neural network was combined with mathematical model to calculate convective heat-transfer coefficient of laminar flow cooling. The off-line calculated results indicate that the standard deviation of coiling temperature prediction is reduced by 22.84 % with the convective heat-transfer coefficient calculated by BP neural network. The prospects of this method for on-line application are bright. This method is more helpful to increasing the control precision of coiling temperature for hot strip steel.

  19. Roll caster for the three-layer clad-strip

    OpenAIRE

    Nakamura, R; T. Yamabayashi; T. Haga; S. Kumai; H. Watari

    2010-01-01

    Purpose: of this paper is to show the characteristics of two kinds of roll casters for three-layer clad strip of aluminium alloys. Moreover, the characteristics of these twin roll casters were compeered with the early type of roll casters for clad strip.Design/methodology/approach: Design was tried to attain the fabrication of the roll casters to cast the three-layers-clad-strip. One caster was an unequal diameter roll caster equipped with a scraper. The scraper was adopted to prevent the mix...

  20. Element Tracking Strategies for Hot Strip Laminar Cooling Control

    Institute of Scientific and Technical Information of China (English)

    HAN Bin; ZHANG Zhong-ping; LIU Xiang-hua; WANG Guo-dong

    2005-01-01

    Feedforward control is the core to control function in the cooling process of hot strip. One of the most important tasks in feedforward control is to determine the arrival time of the strip at various locations on the runout table for effective control. Based on the principles of element tracking and tracking strategies for variable rolling speed and constant rolling speed, a simple diagonal tracking method for an existing hot strip mill was proposed and tested. The test results show that the proposed strategies are effective for improving tracking control.

  1. New technology for the production of magnesium strips and sheets

    Directory of Open Access Journals (Sweden)

    R. Kawalla

    2008-07-01

    Full Text Available A new production technology for magnesium strip, based on twin-roll-casting and strip rolling was developed in Freiberg Germany. By means of this economic method it is possible to produce strips in deep drawing quality with good forming properties in order to satisfy the request for low cost Mg sheets in the automotive and electronic industry. Both, coils as single sheets, were manufactured and rolled to a thickness of 1mm(0,5 mm. The technology of the new process and the properties of the twin-roll-casted material and the final sheets are presented.

  2. Proper Sizing of Circulation Pumps

    DEFF Research Database (Denmark)

    Tommerup, Henrik M.; Nørgaard, Jørgen

    2007-01-01

    , but the results can be applied to Europe in general. Despite the small sample of houses involved in the test, 15 houses, some rather safe conclusions can be drawn from the results, which showed that newly developed pumps with power consumption around 5-8 W, can perform the task of circulating the water...... sufficiently to keep the houses satisfactorily warm during the heating season of the test. The old replaced pumps used 5-10 times more power. In Europe alone, a gradual replacement of the present vastly oversized pumps with such small but sufficient pumps can save the construction of 17 large power plants...... as well as their pollution during operation. Policy measures are proposed of how to ensure that in the future only such energy saving pumps are installed. Furthermore, on the basis of the historic experiences with circulation pumps some con¬clusions are drawn on how to investigate, develop and market new...

  3. Research on synchronous gear pump

    Institute of Scientific and Technical Information of China (English)

    LUAN Zhen-hui

    2010-01-01

    Based on a comprehensive analysis of the structure and existing problems of the gear pump, provided a structure principle of a synchronous gear pump. The discussions focused on the working principle, construction features and finite element analysis of the hydraulic gear. The research indicates that the new pump has such advantages as lower noise, better distributed flow and a high work pressure, and it can be widely used in hydraulic systems.

  4. Centrifugal pumps and allied machinery

    CERN Document Server

    Anderson, HH

    1994-01-01

    This book will be of vital interest to all engineers and designers concerned with centrifugal pumps and turbines. Including statistical information derived from 20000 pumps and 700 turbines with capacities of 5gpm to 5000000gpm, this book offers the widest range and scope of information currently available. Statistical analyses suggest practical methods of increasing pump performance and provide valuable data for new design aspects.

  5. Process Simulation Analysis of HF Stripping

    Directory of Open Access Journals (Sweden)

    Thaer A. Abdulla

    2013-05-01

    Full Text Available    HYSYS process simulator is used for the analysis of existing HF stripping column in LAB plant (Arab Detergent Company, Baiji-Iraq. Simulated column performance and profiles curves are constructed. The variables considered are the thermodynamic model option, bottom temperature, feed temperature, and column profiles for the temperature, vapor flow rate, liquid flow rate and composition. The five thermodynamic models options used (Margules, UNIQUAC, van laar, Antoine, and Zudkevitch-Joffee, affecting the results within (0.1-58% variation for the most cases.        The simulated results show that about 4% of paraffin (C10 & C11 presents at the top stream, which may cause a problem in the LAB production plant. The major variations were noticed for the total top vapor flow rate with bottom temperature and with feed composition. The column profiles maintain fairly constants from tray 5 to tray 18. The study gives evidence about a successful simulation with HYSYS because the results correspond with the real plant operation data.

  6. Profile of a science comic strip author

    CERN Multimedia

    Anaïs Schaeffer

    2014-01-01

    After studying visual arts, Lison Bernet worked as a lock keeper, waitress, grape picker, farm labourer and chef before finally returning to her first love: drawing. Today a scientific illustrator, Lison is the author of the cartoon strip "La BD du LHC", which she draws every month for LHC France (by CNRS/IN2P3 and CEA/Irfu, see here).   © Lison Bernet. Lison’s career path might seem somewhat chaotic, but it is a reflection of the artist herself: original and passionate. “I never do anything by half measures. When I got into cooking for example [Lison took a chef training course for adults], I became completely wrapped up in it. I even went as far as cooking roasts during my lunch hour, just for practice…” says Lison. On completing the course, Lison got a job as a chef on a canal boat. And it was then that she got the drawing bug again. “I started keeping an illustrated travel diary,” she says. &ldquo...

  7. Field measurement of the interactions between heat pumps and attic duct systems in residential buildings

    Energy Technology Data Exchange (ETDEWEB)

    Modera, M.P.; Jump, D.A. [Lawrence Berkeley Lab., CA (United States). Energy and Environment Div.

    1994-11-01

    Research efforts to improve residential heat-pump performance have tended to focus on laboratory and theoretical studies of the machine itself, with some limited field research having been focused on in-situ performance and installation issues. One issue that has received surprisingly little attention is the interaction between the heat pump and the duct system to which it is connected. This paper presents the results of a field study that addresses this interaction. Field performance measurements before and after sealing and insulating the duct systems were made on three heat pumps. From the pre-retrofit data it was found that reductions in heat-pump capacity due to low outdoor temperatures and/or coil frosting are accompanied by lower duct-system energy delivery efficiencies. The conduction loss reductions, and thus the delivery temperature improvements, due to adding duct insulation were found to vary widely depending on the length of the particular duct section, the thermal mass of that duct section, and the cycling characteristics of the heat-pump. In addition, it was found that the use of strip-heat back-up decreased after the retrofits, and that heat-pump cycling increased dramatically after the retrofits, which respectively increase and decrease savings due to the retrofits. Finally, normalized energy use for the three systems which were operated consistently pre- and post-retrofit showed an average reduction of 19% after retrofit, which corresponds to a chance in overall distribution-system efficiency of 24%.

  8. Theoretical Prediction of the Pumping Performance of Dry Pumps (Taking the Scroll Pump and the Screw Pump by Way of Example)

    Science.gov (United States)

    Sawada, Tadashi; Ohbayashi, Tetsuro

    Since almost all commercially provided dry pumps are of the positive displacement type, the leak flow through clearance between displacement chambers in the pump is a dominant factor which determines pumping performance. Prediction methods for the pumping performance of dry pumps are explained by comparing it to the scroll pump and the screw pump. The scroll pump has long clearances, but the screw pump has relatively short ones, and the volume of the chambers reduces from the inlet toward the outlet in the scroll pump, but that in the screw pump is kept constant throughout the pumping process. Such a structural difference produces a small difference in the way of treating leak flow. These two methods can be applied to the other dry pumps requiring only minor modification.

  9. Non-Oriented Fe-Si Thin Strip Produced from Grain Oriented Fe-Si Strip by CSR

    Institute of Scientific and Technical Information of China (English)

    YE He-zhou; QI Ke-min; GAO Xiu-hua; QIU Chun-lin; LIU En

    2004-01-01

    The grain oriented silicon strip was rolled by cross shear rolling (CSR) and then annealed to manufacture non-oriented thin silicon strip of high quality. The recrystallization of rolled grain-oriented silicon steel into non-oriented silicon steel was studied. For this purpose, CSR is better than conventional rolling, and the higher the mismatched speed rate is, the better the properties of the non-oriented thin silicon strip are. The optimum annealing schedule is heating at 1 000 ℃ for 1 h in pure hydrogen atmosphere added with H2S of 0.001 0 %.

  10. Lasers with nuclear pumping

    CERN Document Server

    Melnikov, S P; Sizov, A N; Miley, George H

    2015-01-01

    This book covers the history of lasers with nuclear pumping (Nuclear Pumped Lasers, NPLs). This book showcases the most important results and stages of NPL development in The Russian Federal Nuclear Center (VNIIEF) as well as other Russian and international laboratories, including laboratories in the United States. The basic science and technology behind NPLs along with potential applications are covered throughout the book. As such, this book: ·         Contains a historical overview of the extensive information developed over the past 40 years of work on NPLs ·         Covers the most important results and stages of NPL development, not just in the Russian Federal Nuclear Center, VNIIEF, but also in other laboratories in Russia, the United States , and some other scattered international laboratories ·         Systematizes the fragmented information accumulated over these years of very active research and development As the first comprehensive discussion of NPLs, students, research...

  11. The terrestrial silica pump.

    Directory of Open Access Journals (Sweden)

    Joanna C Carey

    Full Text Available Silicon (Si cycling controls atmospheric CO(2 concentrations and thus, the global climate, through three well-recognized means: chemical weathering of mineral silicates, occlusion of carbon (C to soil phytoliths, and the oceanic biological Si pump. In the latter, oceanic diatoms directly sequester 25.8 Gton C yr(-1, accounting for 43% of the total oceanic net primary production (NPP. However, another important link between C and Si cycling remains largely ignored, specifically the role of Si in terrestrial NPP. Here we show that 55% of terrestrial NPP (33 Gton C yr(-1 is due to active Si-accumulating vegetation, on par with the amount of C sequestered annually via marine diatoms. Our results suggest that similar to oceanic diatoms, the biological Si cycle of land plants also controls atmospheric CO(2 levels. In addition, we provide the first estimates of Si fixed in terrestrial vegetation by major global biome type, highlighting the ecosystems of most dynamic Si fixation. Projected global land use change will convert forests to agricultural lands, increasing the fixation of Si by land plants, and the magnitude of the terrestrial Si pump.

  12. Diode-pumped laser with improved pumping system

    Science.gov (United States)

    Chang, Jim J.

    2004-03-09

    A laser wherein pump radiation from laser diodes is delivered to a pump chamber and into the lasing medium by quasi-three-dimensional compound parabolic concentrator light channels. The light channels have reflective side walls with a curved surface and reflective end walls with a curved surface. A flow tube between the lasing medium and the light channel has a roughened surface.

  13. Stability of flow over axisymmetric bodies with porous suction strips

    Science.gov (United States)

    Nayfeh, A. H.; Reed, H. L.

    1982-01-01

    Linear triple deck, closed form solutions for mean-flow quantities are developed for axisymmetric incompressible flow past a body with porous strips. The solutions account for upstream influence and are linear superpositions of the flow past the body without suction plus the perturbations due to the suction strips. Flow past the suctionless body is calculated using the Transition Analysis Program System, and a simple linear optimization scheme to determine number, spacing, and mass flow rate through the strips on an axisymmetric body is developed using the linear, triple-deck, closed-form solutions. The theory is demonstrated by predicting optimal strip distributions, and the effect of various adverse pressure-gradient situations on stability is studied.

  14. SIMULATION OF THE TWIN ROLL STAINLESS STRIP CASTING PROCESS

    Institute of Scientific and Technical Information of China (English)

    Y.C. Miao; X.M. Zhang; G.D. Wang; H.S. Di; X.H. Liu

    2001-01-01

    The position of the solidification completed temperature of twin roll stainless strip casting process is very important to the quality of the casting strip. In order to control this position, the solidification completed temperature should be known at first.The present paper first simulated dendritic microsegregation under conditions of twin roll stainless strip casting, and got the relationship between the temperature and solid fraction of the mush zone. The temperatures such as ZDT (equal to the solidification completed temperature) and LIT (liquid impenetrable temperature), et al., also were obtained. Then by using the turbulent model, the flow and thermal fields of the pool of the twin roll stainless strip casting, and the speed and temperature fields of different casting speeds were given and also explained. The results are coincident with the experimental result. Combined with the results of these two simulations. the appropriated casting speed was found.

  15. Feasibility and energetic evaluation of air stripping for bioethanol production.

    Science.gov (United States)

    Schläfle, Sandra; Senn, Thomas; Gschwind, Peter; Kohlus, Reinhard

    2017-05-01

    Stripping of mashes with air as stripping gas and low ethanol contents between 3 and 5wt% was investigated in terms of its suitability for continuous bioethanol production. Experiments in a Blenke cascade system were carried out and the results were compared with values obtained from theoretical vapour-liquid-equilibrium calculations. The whole stripping process was energetically evaluated by a simulation in ChemCAD and compared to conventional distillation. Therefore several parameters such as temperature, air volume flow and initial ethanol load of the mash were varied. Air stripping was found to be a suitable separation method for bioethanol from mashes with low concentrations. However, energetic aspects have to be considered, when developing a new process.

  16. Diagnosis of Spontaneous Bacterial Peritonitis in Children by Reagent Strips

    Directory of Open Access Journals (Sweden)

    Fatemeh Farahmand

    2013-02-01

    Full Text Available This study was aimed to evaluate the efficacy of dipstick tests (leukocyte esterase and nitrite in diagnosis of spontaneous bacterial peritonitis (SBP in cirrhotic patients. Forty six children with ascites hospitalized between 2009 and 2010 in Children Medical Center were enrolled in this study. Reagent strip assays for leukocyte esterase and nitrite were performed on ascetic fluid and the results were compared to manual cell counting and ascitic fluid culture. SBP was defined as having a polymorphonuclear ascites count of ≥ 250/mm3. Twenty children were female and twenty six were male with mean age of 3±3.9 years. The sensitivity specificity, positive and negative predictive values of the leukocyte esterase reagent strips were all 100%. The sensitivity, specificity, positive and negative predictive value of the nitrite reagent strip test were 100%, 97%, 90% and 100% respectively. Leukocyte esterase reagent strips may provide a rapid, bedside diagnostic test for the diagnosis of SBP.

  17. Results of Laboratory Testing of Advanced Power Strips: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Earle, L.; Sparn, B.

    2012-08-01

    This paper describes the results of a laboratory investigation to evaluate the technical performance of advanced power strip (APS) devices when subjected to a range of home entertainment center and home office usage scenarios.

  18. Slow-plasmon resonant nano-strip antennas

    DEFF Research Database (Denmark)

    Søndergaard, Thomas; Beermann, Jonas; Boltasseva, Alexandra

    2008-01-01

    Resonant scattering by gold nanostrip antennas due to constructive interference of counterpropagating slow surface plasmon polaritons SPPs is analyzed, including the quasistatic limit of ultrasmall antennas, and experimentally demonstrated. The phase of slow SPP reflection by strip ends is found...

  19. Nanoscale Test Strips for Multiplexed Blood Analysis Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The goal of our nanoscale test strips, or nanostrips, is to provide rapid, low-cost, powerful multiplexed analyses in a diminutive form so that whole body health...

  20. Installation of some Cathode Strip Chambers on March 2004

    CERN Multimedia

    Richard Breedon

    2004-01-01

    Installation on the Disk of some Cathode Strip Chambers, type ME3/1, produced in the US. The installation has been performed on March 2004 at the CMS experimental site SX5 (P5) in Cessy, neighbouring France.

  1. The New Silicon Strip Detectors for the CMS Tracker Upgrade

    CERN Document Server

    Dragicevic, Marko

    2010-01-01

    The first introductory part of the thesis describes the concept of the CMS experiment. The tasks of the various detector systems and their technical implementations in CMS are explained. To facilitate the understanding of the basic principles of silicon strip sensors, the subsequent chapter discusses the fundamentals in semiconductor technology, with particular emphasis on silicon. The necessary process steps to manufacture strip sensors in a so-called planar process are described in detail. Furthermore, the effects of irradiation on silicon strip sensors are discussed. To conclude the introductory part of the thesis, the design of the silicon strip sensors of the CMS Tracker are described in detail. The choice of the substrate material and the complex geometry of the sensors are reviewed and the quality assurance procedures for the production of the sensors are presented. Furthermore the design of the detector modules are described. The main part of this thesis starts with a discussion on the demands on the ...

  2. 33 CFR 157.126 - Pumps.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Pumps. 157.126 Section 157.126... Washing (COW) System on Tank Vessels Design, Equipment, and Installation § 157.126 Pumps. (a) Crude oil must be supplied to the COW machines by COW system pumps or cargo pumps. (b) The pumps under...

  3. Design of Pumps for Water Hydraulic Systems

    DEFF Research Database (Denmark)

    Klit, Peder; Olsen, Stefan; Bech, Thomas Nørgaard

    1999-01-01

    This paper considers the development of two pumps for water hydraulic applications. The pumps are based on two different working principles: The Vane-type pump and the Gear-type pump. Emphasis is put on the considerations that should be made to account for water as the hydraulic fluid.......KEYWORDS: water, pump, design, vane, gear....

  4. About Variable Speed Heating and Cooling Pumps

    OpenAIRE

    Cătălin Popovici; Jan Ignat

    2009-01-01

    The present work has the purpose of underlying the advantages of variable speed heating and cooling pumps use for the perspective of general and particular pumping costs and efficiency. The study approaches comparisons between constant flow pumps and variable flow pumps in different given situations and comparatively analyses the pumping costs.

  5. 46 CFR 119.520 - Bilge pumps.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Bilge pumps. 119.520 Section 119.520 Shipping COAST... Ballast Systems § 119.520 Bilge pumps. (a) Each vessel must be provided with bilge pumps in accordance... have a portable hand bilge pump that must be: (1) Capable of pumping water, but not...

  6. 46 CFR 154.1135 - Pumps.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Pumps. 154.1135 Section 154.1135 Shipping COAST GUARD... Pumps. (a) Water to the water spray system must be supplied by: (1) A pump that is only for the use of the system; (2) A fire pump; or (3) A pump specially approved by the Commandant (CG-522)....

  7. Heat-Powered Pump for Liquid Metals

    Science.gov (United States)

    Campana, R. J.

    1986-01-01

    Proposed thermoelectromagnetic pump for liquid metal powered by waste heat; needs no battery, generator, or other external energy source. Pump turns part of heat in liquid metal into pumping energy. In combination with primary pump or on its own, thermoelectric pump circulates coolant between reactor and radiator. As long as there is decay heat to be removed, unit performs function.

  8. Heat-Powered Pump for Liquid Metals

    Science.gov (United States)

    Campana, R. J.

    1986-01-01

    Proposed thermoelectromagnetic pump for liquid metal powered by waste heat; needs no battery, generator, or other external energy source. Pump turns part of heat in liquid metal into pumping energy. In combination with primary pump or on its own, thermoelectric pump circulates coolant between reactor and radiator. As long as there is decay heat to be removed, unit performs function.

  9. Pumps in wearable ultrafiltration devices: pumps in wuf devices.

    Science.gov (United States)

    Armignacco, Paolo; Garzotto, Francesco; Bellini, Corrado; Neri, Mauro; Lorenzin, Anna; Sartori, Marco; Ronco, Claudio

    2015-01-01

    The wearable artificial kidney (WAK) is a device that is supposed to operate like a real kidney, which permits prolonged, frequent, and continuous dialysis treatments for patients with end-stage renal disease (ESRD). Its functioning is mainly related to its pumping system, as well as to its dialysate-generating and alarm/shutoff ones. A pump is defined as a device that moves fluids by mechanical action. In such a context, blood pumps pull blood from the access side of the dialysis catheter and return the blood at the same rate of flow. The main aim of this paper is to review the current literature on blood pumps, describing the way they have been functioning thus far and how they are being engineered, giving details about the most important parameters that define their quality, thus allowing the production of a radar comparative graph, and listing ideal pumps' features.

  10. Development of Cooling Process Control Technique in Hot Strip Mill

    Institute of Scientific and Technical Information of China (English)

    HAN Bin; LIU Xiang-hua; WANG Guo-dong; SHE Guang-fu

    2005-01-01

    In order to ensure required mechanical properties of steel strip, various innovations in the cooling process control on the run-out table of a hot strip mill were actively promoted. The recent progress of process mathematical model and the new cooling strategy and equipment were discussed. The computer control system of high performance was introduced. The development trend in cooling process control was given.

  11. High speed twin roll casting of 6061 alloy strips

    OpenAIRE

    T. Haga; Sakaguchi, H.; H. Watari; S. Kumai

    2008-01-01

    Purpose: of this paper is to clear the possibility of high speed roll casting of thin strips of two aluminum alloys:6061 and recycled 6061. Mechanical properties of the roll cast 6061 and recycled 6061 strips were investigated inthe frame of this purpose.Design/methodology/approach: Methods used in the present study were high speed twin roll caster and lowtemperature casting. These methods were used to realize rapid solidification and increase the casting speed.Findings: are that 6061 and rec...

  12. A CAD model for the inductive strip in finline

    OpenAIRE

    Knorr, Jeffrey B.

    1988-01-01

    This report describes a CAD compatible circuit model for an inductive strip centered in f inline with W/b=E r2 =1 . The circuit model is shown to predict, strip scattering coefficients which agree closly with those measured experimentally in X-band. By application of the scaling principle the model is generalized for use with any waveguide size over the normal frequency range for the dominant TE 10 mode. Prepared for: Naval Postgraduate School Monterey, CA http://archive.o...

  13. The Strip: Las Vegas and the Symbolic Destruction of Spectacle

    OpenAIRE

    Al, Stefan Johannes

    2010-01-01

    Over the past 70 years, various actors have dramatically reconfigured the Las Vegas Strip in many forms. I claim that behind the Strip's "reinventions" lies a process of symbolic destruction. Since resorts distinguish themselves symbolically, each new round of capital accumulation relies on the destruction of symbolic capital of existing resorts. A new resort either ups the language within a paradigm, or causes a paradigm shift, which devalues the previous resorts even further. This is why, i...

  14. Laser pulse modulation instabilities in partially stripped plasma

    Institute of Scientific and Technical Information of China (English)

    Hu Qiang-Lin; Liu Shi-Bing; Jiang Yi-Jian

    2005-01-01

    The laser pulse modulation instabilities in partially stripped plasma were discussed based on the phase and group velocities of the laser pulse and the two processes that modulation instabilities excited. The excitation condition and growth rate of the modulation instability were obtained. It was found that the positive chirp and competition between normal and abnormal dispersions play important roles in the modulation instability. In the partially stripped plasma,the increased positive chirp enhances the modulation instability, and the dispersion competition reduces it.

  15. The development of drift-strip detectors based on CdZnTe

    DEFF Research Database (Denmark)

    Gostilo, V.; Budtz-Jørgensen, Carl; Kuvvetli, Irfan

    2002-01-01

    The design and technological development of a CdZnTe drift strip detector is described. The device is based on a monocrystal of dimensions 10 x 10 x 3 mm(3) and has a pitch of 200 mum and a strip width of 100 mum. The strip length is 9.5 mm. The distribution of the leakage currents of the strips...

  16. O Processo de Criação de Novos Negócios em Turismo: Estudo de Casos Múltiplos em Agências de Viagens em Curitiba, Paraná

    Directory of Open Access Journals (Sweden)

    Rivanda Meira Teixeira

    2012-08-01

    Full Text Available

    Resumo

    O objetivo deste estudo foi analisar o processo de criação de negócios, identificando os estágios de iniciação, preparação, start up e consolidação em quatro agências de viagens localizadas em Curitiba, Paraná.  Foi adotado o modelo teórico de referência de quatro estágios de Borges, Simard e Filion (2005. O método de pesquisa utilizado foi o estudo de caso múltiplo, e as evidências foram coletadas através de entrevistas pessoais semiestruturadas com os empreendedores. Observou-se que os negócios iniciaram informalmente e que os empreendedores não possuíam informações sobre o setor. No estágio da preparação do negócio, constatou-se que, apesar do apoio gratuito oferecido pelo SEBRAE, os empresários iniciam seus empreendimentos sem realizar o plano de negócios. A consolidação do negócio foi o estágio mais difícil para todos os empreendedores, pois tiveram de lidar com problemas de sazonalidade e dificuldade de gerenciar o fluxo de caixa entre os períodos de alta e baixa estação.  Além disso, os empreendedores apontam grande dificuldade em conciliar a vida pessoal e o negócio. No entanto, apesar das dificuldades enfrentadas, afirmaram que a atividade empresarial é compensadora, em função do retorno financeiro e da satisfação pessoal.

    Palavras-Chave: empreendedorismo; turismo; processo empreendedor; criação de negócios; agências de viagens.Preliminary Design and Evaluation of Portable Electronic Flight Progress Strips

    Science.gov (United States)

    Doble, Nathan A.; Hansman, R. John

    2002-01-01

    There has been growing interest in using electronic alternatives to the paper Flight Progress Strip (FPS) for air traffic control. However, most research has been centered on radar-based control environments, and has not considered the unique operational needs of the airport air traffic control tower. Based on an analysis of the human factors issues for control tower Decision Support Tool (DST) interfaces, a requirement has been identified for an interaction mechanism which replicates the advantages of the paper FPS (e.g., head-up operation, portability) but also enables input and output with DSTs. An approach has been developed which uses a Portable Electronic FPS that has attributes of both a paper strip and an electronic strip. The prototype flight strip system uses Personal Digital Assistants (PDAs) to replace individual paper strips in addition to a central management interface which is displayed on a desktop computer. Each PDA is connected to the management interface via a wireless local area network. The Portable Electronic FPSs replicate the core functionality of paper flight strips and have additional features which provide a heads-up interface to a DST. A departure DST is used as a motivating example. The central management interface is used for aircraft scheduling and sequencing and provides an overview of airport departure operations. This paper will present the design of the Portable Electronic FPS system as well as preliminary evaluation results.

  17. Acrylamide content and color development in fried potato strips

    DEFF Research Database (Denmark)

    Pedreschi, F.; Kaack, K.; Granby, Kit

    2006-01-01

    Acrylamide formation and changes in color of fried potato strips was investigated in relation to frying temperature and three treatments before frying. Potato strips (0.8 x 0.8 x 5 cm) of Bintje variety were fried at 150, 170 and 190 degrees C until reaching moisture contents of similar to 40 g...... and 45 min; 90 degrees C for 3 and 10 min); (iii) immersed in a citric acid solution of 10 g/L for an hour; (iv) immersed in a sodium pyrophosphate solution of 10 g/L for an hour. Acrylamide content and color was determined in the potato strips after frying. Immersed strips in water for 120 min showed...... a reduction of acrylamide formation of 33%, 21% and 27% at 150, 170 and 190 T, respectively, when they were compared against the control. Potato strips blanched at 50 T for 80 min had the lowest acrylamide content when compared against strips blanched at different conditions and fried at the same temperature...

  18. Efficient ozone, sulfate, and ammonium free resist stripping process

    Science.gov (United States)

    Dattilo, Davide; Dietze, Uwe

    2014-07-01

    In recent years, photomask resist strip and cleaning technology development was substantially driven by the industry's need to prevent surface haze formation through the elimination of sulfuric acid and ammonium hydroxide from these processes. As a result, conventional SPM (H2SO4 + H2O2) was replaced with Ozone water (DIO3) for resist stripping and organic removal to eliminate chemical haze formation [1, 2]. However, it has been shown that DIO3 basted strip and clean process causes oxidative degradation of photomask materials [3, 4]. Such material damage can affect optical properties of funcitional mask layers, causeing CD line-width, phase, transmission and reflection changes, adversely affecting image transfer during the Lithography process. To overcome Ozone induced surface damage, SUSS MicroTec successfully developed a highly efficient strip process, where photolysis of DIO3 is leading to highly reactive hydroxyl radical formation, as the main contribution to hydrocarbon removal without surface damage [5]. This technology has been further extended to a final clean process, which is utilizing pure DI water for residual organic material removal during final clean [6]. Recently, SUS MicroTec did also successfully release strip and clean processes which completely remove NH4OH, eliminating any chemicals known today to induce haze [7]. In this paper we show the benefits of these new technologies for highly efficient sulfate and ammonium free stripping and cleaning processes.

  19. Development of a thin steel strip casting process. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Williams, R.S.

    1994-04-01

    This is a comprehensive effort to develop direct strip casting to the point where a pilot scale program for casting carbon steel strip could be initiated. All important aspects of the technology were being investigated, however the program was terminated early due to a change in the business strategy of the primary contractor, Armco Inc. (focus to be directed at specialty steels, not low carbon steel). At termination, the project was on target on all milestones and under budget. Major part was casting of strip at the experiment casting facility. A new caster, capable of producing direct cast strip of up to 12 in. wide in heats of 1000 and 3000 lb, was used. A total of 81 1000-1200 lb heats were cast as well as one test heat of 3000 lb. Most produced strip of from 0.016 to 0.085 in. thick. Process reliability was excellent for short casting times; quality was generally poor from modern hot strip mill standards, but the practices necessary for good surface quality were identified.

  1. Carreira e sucesso em uma revista de negócios: uma análise à luz da quantofrenia gerencialista [doi: 10.21529/RECADM.2015004

    Directory of Open Access Journals (Sweden)

    Carmem Ligia Iochins Grisci

    2015-01-01

    Full Text Available À luz do conceito de quantofrenia gerencialista (Gaulejac, 2007 tomado em sua relação com o estilo de vida característico da sociedade líquido-moderna (Bauman, 2009, o presente estudo indagou: como uma revista popular de negócios vem apresentando as noções de carreira e sucesso ao longo dos últimos anos? E objetivou destacar e analisar as noções de carreira e de sucesso apresentadas por uma revista popular de negócios. Elegeu-se a revista Você S/A para o estudo por considerar-se que ela atua na divulgação e legitimação da lógica gerencialista que contempla a quantofrenia. A coleta de dados privilegiou as chamadas de capa de suas 156 edições publicadas em treze anos (1998-2011. A técnica de análise de conteúdo evidenciou o uso de números e o modo explícito ou latente de apresentação das categorias carreira e sucesso. Os números apontaram dicas, lições, atitudes, ideias e ações que, na arena das escolhas plurais, orientam o estilo de vida (Giddens, 2002. A intensificação do uso de números com destaque evidenciou a quantofrenia relacionada às categorias carreira e sucesso. Prescritiva dos modos de ser e agir para a obtenção de sucesso profissional, a quantofrenia se mostrou implicada ao estilo de vida demandado pelo trabalho.  Palavras-chave Sociedade líquido-moderna; Quantofrenia; Carreira; Sucesso; Estilos de vida.     CAREER AND SUCCESS IN A BUSINESS MAGAZINE: ANALYSIS THROUGH A QUANTOPHRENIAN MANAGEMENT PERSPECTIVE   Abstract This study used the concept of quantophrenia (Gaulejac, 2007 in the liquid-modern society (Bauman, 2009 to investigate how a popular business magazine has presented concepts regarding career and success over the last several years. The study sought to highlight and analyze the concepts of career and success presented by a popular business magazine. Therefore, the magazineVocê S/A was selected because it operates to divulge and provide legitimacy for the management rationale that

  2. Carreira, família e a dialógica do assujeitamento: o discurso vigente em uma revista popular de negócios

    Directory of Open Access Journals (Sweden)

    Andrea Poleto Oltramari

    Full Text Available Há uma série de pesquisas acadêmicas sobre assuntos relacionados à gestão em mídias populares de negócios que possibilitam uma visão do modelo de gestão disseminado na atualidade. O objetivo deste artigo é compreender, por meio do estudo da discursividade em nível verbal e não verbal, como tal modelo gerencial, no que concerne às relações entre carreira e família, revela-se na revista Você S/A. A abordagem teórica do modelo gerencialista é de Vicent de Gaulejac, para quem os princípios da vida são substituídos por princípios interiorizados pela lógica da organização, tornando o sujeito pronto a tudo para ter sucesso. A sustentação metodológica é construída com base nos pressupostos da semiologia barthesiana, por intermédio de três categorias a priori: discurso, estereótipo e mito. Elas estão organizadas em uma disposição que contempla a discursividade, transitando dos seus aspectos mais concretos para os mais abstratos, com a finalidade de facilitar a leitura do nosso objeto. Os resultados indicam que a principal oferta feita ao leitor manifesta-se por meio de uma série de receituários no que concerne à solução dos dilemas relativos à família e/ou carreira, cuja decisão de prioridade, de um lado, fica a cargo do empregado, e do outro, já está predeterminada pela condição de seu assujeitamento.

  3. Mesangiogenic Progenitor Cells Derived from One Novel CD64brightCD31brightCD14neg Population in Human Adult Bone Marrow

    Science.gov (United States)

    Barachini, Serena; Montali, Marina; Carnicelli, Vittoria; Fazzi, Rita; Parchi, Paolo; Petrini, Mario

    2016-01-01

    Mesenchymal stromal cells (MSCs) have been the object of extensive research for decades, due to their intrinsic clinical value. Nonetheless, the unambiguous identification of a unique in vivo MSC progenitor is still lacking, and the hypothesis that these multipotent cells could possibly arise from different in vivo precursors has been gaining consensus in the last years. We identified a novel multipotent cell population in human adult bone marrow that we first named Mesodermal Progenitor Cells (MPCs) for the ability to differentiate toward the mesenchymal lineage, while still retaining angiogenic potential. Despite extensive characterization, MPCs positioning within the differentiation pathway and whether they can be ascribed as possible distinctive progenitor of the MSC lineage is still unclear. In this study, we describe the ex vivo isolation of one novel bone marrow subpopulation (Pop#8) with the ability to generate MPCs. Multicolor flow cytometry in combination with either fluorescence-activated cell sorting or magnetic-activated cell sorting were applied to characterize Pop#8 as CD64brightCD31brightCD14neg. We defined Pop#8 properties in culture, including the potential of Pop#8-derived MPCs to differentiate into MSCs. Gene expression data were suggestive of Pop#8 in vivo involvement in hematopoietic stem cell niche constitution/maintenance. Pop#8 resulted over three logs more frequent than other putative MSC progenitors, corroborating the idea that most of the controversies regarding culture-expanded MSCs could be the consequence of different culture conditions that select or promote particular subpopulations of precursors. PMID:26975798

  4. Absorption and fluorescence characteristics of photo-activated adenylate cyclase nano-clusters from the amoeboflagellate Naegleria gruberi NEG-M strain

    Energy Technology Data Exchange (ETDEWEB)

    Penzkofer, A., E-mail: alfons.penzkofer@physik.uni-regensburg.de [Fakultaet fuer Physik, Universitaet Regensburg, Universitaetsstrasse 31, D-93053 Regensburg (Germany); Stierl, M.; Hegemann, P. [Institut fuer Biologie/Experimentelle Biophysik, Humboldt Universitaet zu Berlin, Invalidenstrasse 42, D-10115 Berlin (Germany); Kateriya, S. [Department of Biochemistry, University of Delhi South Campus, Benito Juarez Road, New Delhi 110021 (India)

    2012-01-02

    Graphical abstract: Protein color center emissions were observed in the wavelength range from 340 nm to 900 nm from nano-clusters of the photo-activated adenylate cyclase (nPAC) from the amoeboflagellate Naegleria gruberi. Highlights: Black-Right-Pointing-Pointer Adenylyl cyclase nPAC in aqueous pH 7.5 buffer dissolved only to nano-clusters. Black-Right-Pointing-Pointer Nano-cluster size was determined by light attenuation (scattering) measurements. Black-Right-Pointing-Pointer The size of the nano-clusters was growing by coalescing during observation period. Black-Right-Pointing-Pointer In nPAC nano-clusters color centers were present in emission range of 360-900 nm. Black-Right-Pointing-Pointer The nPAC color center emission is compared with fluorescent protein emission. - Abstract: The spectroscopic characteristics of BLUF (BLUF = sensor of blue light using flavin) domain containing soluble adenylate cyclase (nPAC = Naegleria photo-activated cyclase) samples from the amoeboflagellate Naegleria gruberi NEG-M strain is studied at room temperature. The absorption and fluorescence spectroscopic development in the dark was investigated over two weeks. Attenuation coefficient spectra, fluorescence quantum distributions, fluorescence quantum yields, and fluorescence excitation distributions were measured. Thawing of frozen nPAC samples gave solutions with varying protein nano-cluster size and varying flavin, tyrosine, tryptophan, and protein color-center emission. Protein color-center emission was observed in the wavelength range of 360-900 nm with narrow emission bands of small Stokes shift and broad emission bands of large Stokes shift. The emission spectra evolved in time with protein nano-cluster aging.

  5. Representações do corpo em uma revista de negócios Body representations in a popular business magazine

    Directory of Open Access Journals (Sweden)

    Cláudia Sirangelo Eccel

    2010-08-01

    Full Text Available O presente artigo resulta de uma pesquisa exploratória que procurou analisar como uma revista de negócios representa o corpo através do que veicula em suas reportagens. As representações encontradas foram categorizadas em dois grupos - gênero e estilo - analisados de acordo com referenciais teóricos sobre o trabalho e o corpo na contemporaneidade. Foi possível identificar que a representação dos corpos na revista passa por uma homogeneização dos estilos de vida no meio executivo. Verificaram-se ainda elementos relativos às prescrições quanto à normalização e adaptação dos corpos a um dado modelo de sucesso profissional que ultrapassa as maneiras de trabalhar e invade a subjetividade dos indivíduos. Além disso, a análise permitiu um olhar sobre o corpo construído e significado de acordo com as exigências da atual sociedade de consumo.This article results from an exploratory study that aimed to analyze how a business magazine represents the body in its reporting. The body representations found were categorized into two groups - gender and style - analyzed in accordance with theoretical references about work and body in the contemporary. Considering the results, it was possible to identify that the body representations in the journal goes through a homogenization of executive's lifestyles. There was also information regarding requirements for standardization and adaptation of the bodies to a particular model of professional success that goes beyond the ways of working and invades the individual's subjectivity. Furthermore, the analysis allowed a glimpse into the body as being built and signified according to the demands of today's consumer society.

  6. Constant-Pressure Hydraulic Pump

    Science.gov (United States)

    Galloway, C. W.

    1982-01-01

    Constant output pressure in gas-driven hydraulic pump would be assured in new design for gas-to-hydraulic power converter. With a force-multiplying ring attached to gas piston, expanding gas would apply constant force on hydraulic piston even though gas pressure drops. As a result, pressure of hydraulic fluid remains steady, and power output of the pump does not vary.

  7. [Treatment by external insulin pump].

    Science.gov (United States)

    Clavel, Sylvaine

    2010-12-01

    Since the recent recommendations by the French speaking association for research on diabetes and metabolic illnesses (Alfediam), treatment by insulin pump has found itself in competition with basal-bolus, a procedure using similar injections of insulin which has become a benchmark treatment. The latest Alfediam guidelines focus on defining ways of treating diabetics with an external insulin pump.

  8. High Temperature Thermoacoustic Heat Pump

    Energy Technology Data Exchange (ETDEWEB)

    Tijani, H.; Spoelstra, S. [ECN Biomass and Energy Efficiency, Petten (Netherlands)

    2012-07-15

    Thermoacoustic technology can provide new types of heat pumps that can be deployed in different applications. Thermoacoustic heat pumps can for example be applied in dwellings to generate cooling or heating. Typically, space and water heating makes up about 60% of domestic and office energy consumption. The application of heat pumps can contribute to achieve energy savings and environmental benefits by reducing CO2 and NOx emissions. This paper presents the study of a laboratory scale thermoacoustic-Stirling heat pump operating between 10C and 80C which can be applied in domestics and offices. The heat pump is driven by a thermoacoustic-Stirling engine. The experimental results show that the heat pump pumps 250 W of heat at 60C at a drive ratio of 3.6 % and 200 W at 80C at a drive ratio of 3.5 %. The performance for both cases is about 40% of the Carnot performance. The design, construction, and performance measurements of the heat pump will be presented and discussed.

  9. Ion-Pumping Microbial Rhodopsins

    Directory of Open Access Journals (Sweden)

    Hideki eKandori

    2015-09-01

    Full Text Available Rhodopsins are light-sensing proteins used in optogenetics. The word rhodopsin originates from the Greek words rhodo and opsis, indicating rose and sight, respectively. Although the classical meaning of rhodopsin is the red-colored pigment in our eyes, the modern meaning of rhodopsin encompasses photoactive proteins containing a retinal chromophore in animals and microbes. Animal and microbial rhodopsins possess 11-cis and all-trans retinal, respectively, to capture light in seven transmembrane α-helices, and photoisomerizations into all-trans and 13-cis forms, respectively, initiate each function. Ion-transporting proteins can be found in microbial rhodopsins, such as light-gated channels and light-driven pumps, which are the main tools in optogenetics. Light-driven pumps, such as archaeal H+ pump bacteriorhodopsin (BR and Cl- pump halorhodopsin (HR, were discovered in the 1970s, and their mechanism has been extensively studied. On the other hand, different kinds of H+ and Cl- pumps have been found in marine bacteria, such as proteorhodopsin (PR and Fulvimarina pelagi rhodopsin (FR, respectively. In addition, a light-driven Na+ pump was found, Krokinobacter eikastus rhodopsin 2 (KR2. These light-driven ion-pumping microbial rhodopsins are classified as DTD, TSA, DTE, NTQ and NDQ rhodopsins for BR, HR, PR, FR and KR2, respectively. Recent understanding of ion-pumping microbial rhodopsins is reviewed in this paper.

  10. Microstructure and Eutectic Carbide Morphology of the High Speed Steel Strips Produced by Twin Roll Strip Casting Process

    Institute of Scientific and Technical Information of China (English)

    Hongshuang DI; Xiaoming ZHANG; Guodong WANG; Xianghua LIU

    2003-01-01

    The M2 high-speed steel strip was produced by using the laboratory scale twin roll strip caster. The microstructureand eutectic carbide morphology of thus produced products were observed and analyzed, and the comparison ofthose with conventional products was carried out. The effects of the processing parameters such as the meltingtemperature, the pouring temperature, rolling speed and separating force on the microstructure and eutectic carbidemorphology and their distribution were analyzed. The spheroidizing process of the strips in the annealing process wasinvestigated. The relations between the growth and spheroidizing of the eutectic carbide and the annealing technologywere obtained, and the mechanism of the twin roll strip casting process improving the eutectic carbide spheroidizingwas discussed. The theoretical instruction for determining the subsequent treatment process was provided.

  11. Hydrological heterogeneity in agricultural riparian buffer strips

    Science.gov (United States)

    Hénault-Ethier, Louise; Larocque, Marie; Perron, Rachel; Wiseman, Natalie; Labrecque, Michel

    2017-03-01

    Riparian buffer strips (RBS) may protect surface water and groundwater in agricultural settings, although their effectiveness, observed in field-scale studies, may not extend to a watershed scale. Hydrologically-controlled leaching plots have often shown RBS to be effective at buffering nutrients and pesticides, but uncontrolled field studies have sometimes suggested limited effectiveness. The limited RBS effectiveness may be explained by the spatiotemporal hydrological heterogeneity near non-irrigated fields. This hypothesis was tested in conventional corn and soy fields in the St. Lawrence Lowlands of southern Quebec (Canada), where spring melt brings heavy and rapid runoff, while summer months are hot and dry. One field with a mineral soil (Saint-Roch-de-l'Achigan) and another with an organic-rich soil (Boisbriand) were equipped with passive runoff collectors, suction cup lysimeters, and piezometers placed before and after a 3 m-wide RBS, and monitored from 2011 to 2014. Soil topography of the RBS was mapped to a 1 cm vertical precision and a 50 cm sampling grid. On average, surface runoff intersects the RBS perpendicularly, but is subject to substantial local heterogeneity. Groundwater saturates the root zones, but flows little at the time of snowmelt. Groundwater flow is not consistently perpendicular to the RBS, and may reverse, flowing from stream to field under low water flow regimes with stream-aquifer connectivity, thus affecting RBS effectiveness calculations. Groundwater flow direction can be influenced by stratigraphy, local soil hydraulic properties, and historical modification of the agricultural stream beds. Understanding the spatiotemporal heterogeneity of surface and groundwater flows is essential to correctly assess the effectiveness of RBS in intercepting agro-chemical pollution. The implicit assumption that water flows across vegetated RBS, from the field to the stream, should always be verified.

  12. Insulin pump therapy in pregnancy.

    Science.gov (United States)

    Kesavadev, Jothydev

    2016-09-01

    Control of blood glucose during pregnancy is difficult because of wide variations, ongoing hormonal changes and mood swings. The need for multiple injections, pain at the injection site, regular monitoring and skillful handling of the syringes/pen further makes insulin therapy inconvenient. Insulin pump is gaining popularity in pregnancy because it mimics the insulin delivery of a healthy human pancreas. Multiple guidelines have also recommended the use of insulin pump in pregnancy to maintain the glycaemic control. The pump can release small doses of insulin continuously (basal), or a bolus dose close to mealtime to control the spike in blood glucose after a meal and the newer devices can shut down insulin delivery before the occurrence of hypoglycaemia. Pump insulin of choice is rapid acting analogue insulin. This review underscores the role of insulin pump in pregnancy, their usage, advantages and disadvantages in the light of existing literature and clinic experience.

  13. A data pump for communication

    Science.gov (United States)

    Kang, Myong H.; Moskowitz, Ira S.

    1995-09-01

    As computer systems become more open and interconnected, the need for reliable and secure communication also increases. In this paper, we introduce a communication device, the Pump, that balances the requirements of reliability and security. The Pump provides acknowledgements (ACK's) to the message source to insure reliability. These ACK's are also used to regulate the source to prevent the Pump's buffer from becoming/staying full. This is desirable because once the buffer is filled there exists a huge covert communication channel. The Pump controls the input rate from the source by attempting to slave the input rate to the service rate through the randomized ACK back to the source. An analysis of the covert channel is also presented. The purpose of the covert channel analysis is to provide guidelines for the designer of the Pump to choose appropriate design parameters (e.g., size of buffer) dependent upon the analysis presented in this paper and system requirements.

  14. A Low-Profile Dual-Band Micro-strip Antenna Having Open-Circuited Strip-line-Stub

    OpenAIRE

    長谷川, 孝明; 羽石, 操

    1986-01-01

    Copyright notice. c1986 IEICE All rights reserved. "A Low-Profile Dual-Band Micro-strip Antenna Having Open-Circuited Strip-line-Stub"Misao HANEISHI, Hidekazu SUGA, Takaaki HASEGAWA.The Transactions of the Institute of Electronics and Communication Engineers of Japan. Section E, English, 1986. Vol. E69 No.11 pp. 1165-1166 許諾No.07RB0055.

  15. Peltier heat pumps. Peltiervaermepumpar

    Energy Technology Data Exchange (ETDEWEB)

    Torstensson, H. (Studsvik Energy, Nykoeping (SE))

    1990-06-01

    Todays Peltier devices in heat pump applications gives a low coeffificent of performance. A temperature difference of 40 deg C results in a COP-value of approx. 1.3. Peltier devices are manufactured of alloys composed of heavy elements like tellurium, selenium, bismuth and antimony. These elements thermoelectrical properties, figure of merit are decisive to the performance of the Peltier devices. An upper limit for the figure of merit, ZT, is said to be 2, which at {Delta}T=40 deg C would yield a COP of 2.0 as a maximum. Organic compounds have been investigated with regard to the electric conductivity. Thin film technique have been used for Peltier devices in micro-scale. There are no large-scale applications. The method does not give enhanced termoelectrical properties, but more rational and cheaper manufacturing. (author) (47 refs., 26 figs.).

  16. Self pumping magnetic cooling

    Science.gov (United States)

    Chaudhary, V.; Wang, Z.; Ray, A.; Sridhar, I.; Ramanujan, R. V.

    2017-01-01

    Efficient thermal management and heat recovery devices are of high technological significance for innovative energy conservation solutions. We describe a study of a self-pumping magnetic cooling device, which does not require external energy input, employing Mn-Zn ferrite nanoparticles suspended in water. The device performance depends strongly on magnetic field strength, nanoparticle content in the fluid and heat load temperature. Cooling (ΔT) by ~20 °C and ~28 °C was achieved by the application of 0.3 T magnetic field when the initial temperature of the heat load was 64 °C and 87 °C, respectively. These experiments results were in good agreement with simulations performed with COMSOL Multiphysics. Our system is a self-regulating device; as the heat load increases, the magnetization of the ferrofluid decreases; leading to an increase in the fluid velocity and consequently, faster heat transfer from the heat source to the heat sink.

  17. PLT rotating pumped limiter

    Energy Technology Data Exchange (ETDEWEB)

    Cohen, S.A.; Budny, R.V.; Corso, V.; Boychuck, J.; Grisham, L.; Heifetz, D.; Hosea, J.; Luyber, S.; Loprest, P.; Manos, D.

    1984-07-01

    A limiter with a specially contoured front face and the ability to rotate during tokamak discharges has been installed in a PLT pump duct. These features have been selected to handle the unique particle removal and heat load requirements of ICRF heating and lower-hybrid current-drive experiments. The limiter has been conditioned and commissioned in an ion-beam test stand by irradiation with 1 MW power, 200 ms duration beams of 40 keV hydrogen ions. Operation in PLT during ohmic discharges has proven the ability of the limiter to reduce localized heating caused by energetic electron bombardment and to remove about 2% of the ions lost to the PLT walls and limiters.

  18. Electric fluid pump

    Science.gov (United States)

    Van Dam, Jeremy Daniel; Turnquist, Norman Arnold; Raminosoa, Tsarafidy; Shah, Manoj Ramprasad; Shen, Xiaochun

    2015-09-29

    An electric machine is presented. The electric machine includes a hollow rotor; and a stator disposed within the hollow rotor, the stator defining a flow channel. The hollow rotor includes a first end portion defining a fluid inlet, a second end portion defining a fluid outlet; the fluid inlet, the fluid outlet, and the flow channel of the stator being configured to allow passage of a fluid from the fluid inlet to the fluid outlet via the flow channel; and wherein the hollow rotor is characterized by a largest cross-sectional area of hollow rotor, and wherein the flow channel is characterized by a smallest cross-sectional area of the flow channel, wherein the smallest cross-sectional area of the flow channel is at least about 25% of the largest cross-sectional area of the hollow rotor. An electric fluid pump and a power generation system are also presented.

  19. Heat pumps in industry. Pt. 2: Applications

    Energy Technology Data Exchange (ETDEWEB)

    Lazzarin, R.M. [Padova Univ., Vicenza (Italy). Ist. di Ingegneria Gestionale

    1995-04-01

    A selection of applications of heat pumps in industry is described, reporting plant lay-outs and performances. The selection includes compression heat pumps at different temperatures, vapour recompression systems, absorption heat pumps and heat transformers. (author)

  20. Control Strategies of Asymmetric Strip Shape in Six-High Cold Rolling Mill%Control Strategies of Asymmetric Strip Shape in Six-High Cold Rolling Mill

    Institute of Scientific and Technical Information of China (English)

    ZHANG Yun; YANG Quan; WANG Xiao-chen

    2011-01-01

    It is a complicated problem for cold-rolled strip to improve asymmetric strip shape in strip production. A roll system and strip coupled model of six-high cold rolling mill was established with finite element method to estimate the effect of intermediate roll shifting, tilting, symmetric and asymmetric bending technologies on strip profile. To reduce asymmetric defects of strip shape as much as possible, some control strategies were proposed, including tilting and asymmetric bending of intermediate roll and work roll. The combinations of these three control strategies can effectively eliminate asymmetric strip shape defects. Finally, the closed-loop control model of asymmetric flat- ness at the last stand was given, and the flatness control system with the function of asymmetric strip shape control was also designed for cold tandem mill.

  1. Automatic Control of Water Pumping Stations

    Institute of Scientific and Technical Information of China (English)

    Muhannad Alrheeh; JIANG Zhengfeng

    2006-01-01

    Automatic Control of pumps is an interesting proposal to operate water pumping stations among many kinds of water pumping stations according to their functions.In this paper, our pumping station is being used for water supply system. This paper is to introduce the idea of pump controller and the important factors that must be considering when we want to design automatic control system of water pumping stations. Then the automatic control circuit with the function of all components will be introduced.

  2. Microstructural Characterization of Novel Ni-Containing Nd-Fe-B Strips by Strip Casting

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The characteristics of novel Nd-Fe(Ni, Co, Al)-B microstructure prepared by strip casting technique were studied. The novel microstructure was observed using scanning electron microscope (SEM) and transmission electron microscope (TEM). Along the direction of heat flow, there are two kinds of different microstructures. Close to the wheel side, there is a thick layer containing many polygonal Nd2Fe14B grains. Near the free surface side, however, there are relative uniform platelike Nd2Fe14B grains whose growth direction is not completely the direction of the heat flow during solidification. The formation of the novel microstructure is presumed to be the contribution of the special temperature field and Ni component.

  3. Pumping of titanium sapphire laser

    Science.gov (United States)

    Jelínková, H.; Vaněk, P.; Valach, P.; Hamal, K.; Kubelka, J.; Škoda, V.; Jelínek, M.

    1993-02-01

    Two methods of Ti:Sapphire pumping for the generation of tunable laser radiation in the visible region were studied. For coherent pumping, the radiation of the second harmonic of a Nd:YAP laser was used and a maximum output energy of E out=4.5 mJ was reached from the Ti:Sapphire laser. For noncoherent pumping, two different lengths of flashlamp pulses were used and a maximum of E out=300 mJ was obtained. Preliminary estimations of the wavelength range of tunability were made.

  4. Industrial heat pump assessment study

    Science.gov (United States)

    Chappell, R. N.; Priebe, S. J.; Wilfert, G. L.

    1989-03-01

    This report summarizes preliminary studies that assess the potential of industrial heat pumps for reduction of process heating requirements in industries receiving power from the Bonneville Power Administration (BPA). This project was initiated at the request of BPA to determine the potential of industrial heat pumps in BPA's service area. Working from known heat pump principles and from a list of BPA's industrial customers, the authors estimated the fuel savings potential for six industries. Findings indicate that the pulp and paper industry would yield the greatest fuel savings and increased electrical consumption. Assessments presented in this report represent a cooperative effort between The Idaho National Engineering Laboratory (INEL), and Battelle-Northwest Laboratories.

  5. Heat pumps for the home

    CERN Document Server

    Cantor, John

    2013-01-01

    In recent years, heat pumps have emerged as a promising new form of technology with a relatively low environmental impact. Moreover, they have presented householders with an opportunity to reduce their heating bills. Heat pumps can heat a building by 'pumping' heat from either the ground or the air outside: an intriguing process which utilizes principles that are somewhat analogous to those employed in the domestic refrigerator. Armed with the practical information contained in these pages, homeowners will have the necessary knowledge to take advantage of this potentially low-carbon t

  6. Stripped Elliptical Galaxies as Probes of ICM Physics: I. Tails, Wakes, and Flow Patterns in and Around Stripped Ellipticals

    Science.gov (United States)

    Roediger, E.; Kraft, R. P.; Nulsen, P. E. J.; Forman, W. R.; Machacek, M.; Randall, S.; Jones, C.; Churazov, E.; Kokotanekova, R.

    2015-06-01

    Elliptical cluster galaxies are progressively stripped of their atmospheres due to their motion through the intracluster medium (ICM). Deep X-ray observations reveal the fine-structure of the galaxy’s remnant atmosphere and its gas tail and wake. This fine-structure depends on dynamic conditions (galaxy potential, initial gas contents, orbit through the host cluster), orbital stage (early infall, pre-/post-pericenter passage), and ICM plasma properties (thermal conductivity, viscosity, magnetic field structure). We aim to disentangle dynamic and plasma effects in order to use stripped ellipticals as probes of ICM plasma properties. This first paper of a series investigates the hydrodynamics of progressive gas stripping by means of inviscid hydrodynamical simulations. We distinguish a long-lasting initial relaxation phase and a quasi-steady stripping phase. During quasi-steady stripping, the ICM flow around the remnant atmosphere resembles the flow around solid bodies, including a “deadwater” region in the near wake. Gas is stripped from the remnant atmosphere predominantly at its sides via Kelvin-Helmholtz instabilities. The downstream atmosphere is largely shielded from the ICM wind and thus shaped into a tail. Observationally, both this “remnant tail” and the stripped gas in the wake can appear as a “tail”, but only in the wake can galactic gas mix with the ambient ICM. While the qualitative results are generic, the simulations presented here are tailored to the Virgo elliptical galaxy M89 (NGC 4552) for the most direct comparison to observations. Papers II and III of this series describe the effect of viscosity and compare to Chandra and XMM-Newton observations, respectively.

  7. STRIPPED ELLIPTICAL GALAXIES AS PROBES OF ICM PHYSICS. I. TAILS, WAKES, AND FLOW PATTERNS IN AND AROUND STRIPPED ELLIPTICALS

    Energy Technology Data Exchange (ETDEWEB)

    Roediger, E. [Hamburger Sternwarte, Universität Hamburg, Gojensbergsweg 112, D-21029 Hamburg (Germany); Kraft, R. P.; Nulsen, P. E. J.; Forman, W. R.; Machacek, M.; Randall, S.; Jones, C. [Harvard/Smithsonian Center for Astrophysics, 60 Garden Street MS-4, Cambridge, MA 02138 (United States); Churazov, E. [MPI für Astrophysik, Karl-Schwarzschild-Str. 1, Garching, D-85741 (Germany); Kokotanekova, R., E-mail: eroediger@hs.uni-hamburg.de [AstroMundus Master Programme, University of Innsbruck, Technikerstr. 25/8, 6020 Innsbruck (Austria)

    2015-06-10

    Elliptical cluster galaxies are progressively stripped of their atmospheres due to their motion through the intracluster medium (ICM). Deep X-ray observations reveal the fine-structure of the galaxy’s remnant atmosphere and its gas tail and wake. This fine-structure depends on dynamic conditions (galaxy potential, initial gas contents, orbit through the host cluster), orbital stage (early infall, pre-/post-pericenter passage), and ICM plasma properties (thermal conductivity, viscosity, magnetic field structure). We aim to disentangle dynamic and plasma effects in order to use stripped ellipticals as probes of ICM plasma properties. This first paper of a series investigates the hydrodynamics of progressive gas stripping by means of inviscid hydrodynamical simulations. We distinguish a long-lasting initial relaxation phase and a quasi-steady stripping phase. During quasi-steady stripping, the ICM flow around the remnant atmosphere resembles the flow around solid bodies, including a “deadwater” region in the near wake. Gas is stripped from the remnant atmosphere predominantly at its sides via Kelvin–Helmholtz instabilities. The downstream atmosphere is largely shielded from the ICM wind and thus shaped into a tail. Observationally, both this “remnant tail” and the stripped gas in the wake can appear as a “tail”, but only in the wake can galactic gas mix with the ambient ICM. While the qualitative results are generic, the simulations presented here are tailored to the Virgo elliptical galaxy M89 (NGC 4552) for the most direct comparison to observations. Papers II and III of this series describe the effect of viscosity and compare to Chandra and XMM-Newton observations, respectively.

  8. Summary of the LLNL gasoline spill demonstration - dynamic underground stripping project

    Energy Technology Data Exchange (ETDEWEB)

    Newmark, R.L.; Aines, R.D.

    1995-04-03

    Underground spills of volatile hydrocarbons (solvents or fuels) can be difficult to clean up when the hydrocarbons are present both above and below the water table and are found in relatively impermeable clays. Years of groundwater pumping may not completely remove the contamination. Researchers at Lawrence Livermore National Laboratory (LLNL) and the College of Engineering at the University of California at Berkeley (UCB) have collaborated to develop a technique called Dynamic Underground Stripping to remove localized underground spills in a relatively short time. The U.S. Department of Energy`s Office of Environmental Restoration and Waste Management has sponsored a full-scale demonstration of this technique at the LLNL gasoline spill site. When highly concentrated contamination is found above the standing water table, vacuum extraction has been very effective at both removing the contaminant and enhancing biological remediation through the addition of oxygen. Below the water table, however, these advantages cannot be obtained. For such sites where the contamination is too deep for excavation, there are currently no widely applicable cleanup methods. Dynamic Underground Stripping removes separate-phase organic contaminants below the water table by heating the subsurface above the boiling point of water, and then removing both contaminant and water by vacuum extraction. The high temperatures both convert the organic to vapor and enhance other removal paths by increasing diffusion and eliminating sorption. Because this method uses rapid, high-energy techniques in cleaning the soil, it requires an integrated system of underground monitoring and imaging methods to control and evaluate the process in real time.

  9. Nanozyme-strip for rapid local diagnosis of Ebola.

    Science.gov (United States)

    Duan, Demin; Fan, Kelong; Zhang, Dexi; Tan, Shuguang; Liang, Mifang; Liu, Yang; Zhang, Jianlin; Zhang, Panhe; Liu, Wei; Qiu, Xiangguo; Kobinger, Gary P; Gao, George Fu; Yan, Xiyun

    2015-12-15

    Ebola continues to rage in West Africa. In the absence of an approved vaccine or treatment, the priority in controlling this epidemic is to promptly identify and isolate infected individuals. To this end, a rapid, highly sensitive, and easy-to-use test for Ebola diagnosis is urgently needed. Here, by using Fe3O4 magnetic nanoparticle (MNP) as a nanozyme probe, we developed a MNP-based immunochromatographic strip (Nanozyme-strip), which detects the glycoprotein of Ebola virus (EBOV) as low as 1 ng/mL, which is 100-fold more sensitive than the standard strip method. The sensitivity of the Nanozyme-strip for EBOV detection and diagnostic accuracy for New Bunyavirus clinical samples is comparable with ELISA, but is much faster (within 30 min) and simpler (without need of specialist facilities). The results demonstrate that the Nanozyme-strip test can rapidly and sensitively detect EBOV, providing a valuable simple screening tool for diagnosis of infection in Ebola-stricken areas.

  10. Prototype indicator strip for tank ammunition. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Bates, B.; Griest, W.

    1993-10-31

    Combustible nitrocellulose ordnance casings offer advantages of: light weight, low cost, low detectability, and quick cycling of rounds by immediate disposal. However, mechanical strength is degraded with time by the action of humidity and nitroester diffusion through the casing to adhesives. The primary development effort of this study is a means to detect nitroester migration to the crucial skive joint which binds an assortment of warhead choices to propellant casings. This work has developed a prototype colorimetric indicator strip which, when applied in a field environment, produces a purple tint proportional to casing nitroester concentration, and inversely proportional to remaining adhesive joint strength. This work addressed the three steps in indicator strip use: (1) A suggested protocol for indicator strip preparation was developed. Various coatings, support reagents, and backings were examined resulting in a choice of polyethylene tape coating over separate AB- and C-impregnated cellulose punches. Various methods of punch creation and impregnation were tried resulting in stirred aqueous solutions and suspensions of AB and C, respectively. (2) Suggested protocols for indicator strip application to lab backings and field casings were developed. After chemical stripper was applied to the alumina-polyurethane paint on casings, C and AB punches were stacked and double-tape sealed. (3) A means for indicator strip monitoring was developed. From known time of indicator reaction, casing humidity, and indicator color, a means for field concentration determination was determined. Lab time-lapse photography was used to calibrate the indicator at a single level of humidity.

  11. Calculation and Analysis of Temperature Distribution in Hot Rolling Strip

    Directory of Open Access Journals (Sweden)

    Kaixiang Peng

    2013-07-01

    Full Text Available Modern steel grades require constant and reproducible production conditions both in the hot strip mill and in the cooling section to achieve constant material properties along the entire strip length and from strip to strip. Calculation of the temperature in final rolling process always utilizes factors such as the work piece's inner organizational structure, plastic deformation, and it's variations of properties and so on, also as well as the physical parameters such as gauge, shape, etc. In this paper, a finite element model is constructed for the temperature field in a rolling process. The temperature field of strip steel is modeled with a 3-D finite element analysis (FEA structure, simultaneously considering the distribution of the work roll temperature. Then the distribution of field is simulated numerically. From the model, the temperature contours can be obtained by analysis of the temperature distribution of contact area. At the same time, the distribution of temperature in any position at any time can be acquired. These efforts provide the reliable parameters for the later finishing temperature and shape control.  

  12. VTT's micron-scale silicon rib+strip waveguide platform

    Science.gov (United States)

    Aalto, Timo; Harjanne, Mikko; Cherchi, Matteo

    2016-05-01

    Silicon rib waveguides enable single-mode (SM) operation even with the combination of multi-micron core dimensions and high refractive index contrast. In such large waveguides the optical mode field is almost completely confined inside the Si core, which leads to small propagation losses and small polarization dependency. The unique SM condition of the rib waveguide also enables the use of an ultra-wide wavelength range, for example from 1.2 to <1.7 μm, without sacrificing either SM operation or low propagation loss. This makes micron-scale Si waveguides particularly well-suited for spectroscopy and extensive wavelength division multiplexing. However, rib waveguides require large bending radii, which lead to large circuit sizes. There are two solutions for this. So-called Euler bends in Si strip waveguides enable low-loss bends down to 1 μm bending radius with less than 0.1 dB/90° loss for both polarizations. Another alternative is a total-internal reflection mirror that can have loss as low as 0.1 dB for both polarizations in either strip or rib waveguides. The excitation of higher order modes in large strip waveguides is avoided by using adiabatic rib-strip converters and low-loss components. With rib and strip waveguides it is possible to reach a unique combination of low loss, extremely small footprint, small polarization dependency, ultra-wide bandwidth and tolerance to high optical powers.

  13. Unidades estratégicas de negócios: uma ferramenta para gestão competitiva de empresas Strategic business units: a tool for the competitive management

    Directory of Open Access Journals (Sweden)

    José Paulo Alves Fusco

    1997-04-01

    Full Text Available Este artigo tem por objetivo discutir e apresentar algumas considerações acerca das vantagens e implicações da utilização do conceito de UEN - Unidade Estratégica de Negócios, na gestão de empresas, de modo geral. O artigo discute algumas relações que devem ser esclarecidas antes da plena adoção do conceito. Baseado na literatura e na experiência do autor em consultoria em empresas, o artigo propõe uma abordagem metodológica para permitir que gerentes possam definir, analisar e compreender os efeitos da utilização do conceito de UEN - Unidade Estratégica de Negócios, considerando as dimensões competitivas ou Fatores Críticos de Sucesso típicos e intrínsecos da natureza de cada negócio.This paper is an attempt to discuss and present some considerations concerning the advantages and relationships involving the adoption of the SBU - Strategic Business Unit concepts and business management in a broad sense. The paper discusses some aspects which must be clarified before a full adoption of the concepts. Based on the literature and the author's experience in business consultancy, the paper suggests a methodological approach which aims to help managers to define, analyse and understand the effects of the adoption of the SBU concepts, considering the typical competitive dimensions (critical success factors involved in any kind of business.

  14. Modelagem de processos de negócios na implementação de ERPs nacionais em PMEs Business processes modeling in the implementation of national ERPs within SMEs

    Directory of Open Access Journals (Sweden)

    Fernanda Pereira Carneiro da Silva

    2006-08-01

    Full Text Available Este artigo apresenta evidências encontradas em uma pesquisa que teve como objetivo investigar a contribuição do uso da Modelagem dos Processos dos Negócios (MPN na implementação do Enterprise Resource Planning (ERP em pequenas e médias empresas (PMEs. Foi observado, nos principais fornecedores nacionais deste sistema, o uso da MPN, verificando sua influência na integração dos processos internos dos negócios de seus clientes. Para esta investigação buscaram-se as informações nos fornecedores nacionais de sistema ERP e seus clientes, mediante questionários específicos. Esta pesquisa possibilitou obter informações reais das principais características de implementação nas PMEs, destacando-se como a MPN contribui efetivamente na implementação para otimizar a integração dos processos internos dos negócios.This article presents evidences found in a research whose objective was to investigate the contribution of using business processes modeling (BPM in the implementation of Enterprise Resource Planning (ERP in small and middle companies (SMEs. The use of the BPM and assessment of its influence for the integration of the internal business processes of their customers, was also observed in the main national ERP system suppliers. To carry out this research, information was obtained by means of specific questionnaires answered by the national ERP system suppliers and their customers. This research allowed to obtain actual data about the main implementation characteristics within the SMEs, showing how the BPM effectively contributes for the implementation and better integration of the internal business processes.

  15. Modelo de Negócio: As Operações de uma Distribuidora de Combustíveis no Complexo Industrial Portuário de Suape/PE

    Directory of Open Access Journals (Sweden)

    Davi Lucas Arruda de Araújo

    2017-04-01

    Full Text Available O objetivo principal desta pesquisa consiste em identificar as dimensões do modelo de negócios utilizando o Canvas Business Model, da empresa ALFA Combustíveis no Complexo Industrial Portuário de Suape/PE. O estudo é de natureza exploratória e foi desenvolvido mediante uma pesquisa de campo qualitativa. A coleta de dados ocorreu por meio de entrevistas semiestruturadas considerando como sujeitos de pesquisa profissionais desta distribuidora que atuam na base de operações do complexo de Suape/PE. E no tratamento, interpretação e análise dos resultados acerca dos dados coletados foi utilizada a técnica de categorização baseado em (Flores, 1994. Os resultados revelam que a empresa, no que diz respeito a oferta de valor, desenvolve ações para melhoria da eficiência na prestação do serviço. No que tange a infraestrutura, pessoas com expertise, atividades bem alinhadas e política de custos bem definidas são necessárias para o desenvolvimento deste tipo de negócio. E, no que se refere aos clientes, a segmentação em postos revendedores, o desenvolvimento de softwares que auxiliam no relacionamento com os clientes, projetos de entrega de produtos em tempo hábil e delimitação das fontes de receitas em função das atividades que são executadas na base configuram o modelo de negócio de uma distribuidora de combustíveis.

  16. Perspectivas do alinhamento estratégico entre negócios e tecnologia da informação em pequenas empresas de software do porto digital: um prisma de divergentes facetas

    Directory of Open Access Journals (Sweden)

    Maria Conceição Melo Silva

    2010-08-01

    Full Text Available Este estudo procurou analisar as perspectivas do alinhamento estratégico entre estratégia de negócios e tecnologia da informação nas pequenas empresas de software do Porto Digital e justifica-se pela carência de estudos similares, uma vez que, na maior parte dos casos, apenas geram corpo teórico estudos relacionados às práticas de alinhamento estratégico para grandes empresas. De fato, o alinhamento estratégico entre negócio e tecnologia da informação é um dos temas que mais tem sido discutido na academia, devido ao interesse de aproximação da área de negócios com a área de tecnologia da informação (TI, para um maior desempenho das empresas no cenário competitivo, mas recursivamente tem se voltado a corporações de maior porte. A pesquisa caracterizou-se como exploratória e descritiva e se deu por meio da estratégia de estudo de casos múltiplos, empregando a técnica de análise de conteúdo, além de uma análise interpretativa dos achados, a partir dos níveis e critérios do modelo de maturidade do alinhamento estratégico de Luftman (2000. Os resultados constataram a potencialidade da TI como condutora do alinhamento estratégico, assim como destacaram diferentes facetas do alinhamento estratégico nas empresas estudadas, fato que estimula novas oportunidades de pesquisas.

  17. The use of water as a high temperature heat pump fluid at the Auchroisk distillery, Scotland

    Energy Technology Data Exchange (ETDEWEB)

    Castle, T. [EA Technology Ltd., Chester (United Kingdom)

    1995-12-01

    The first steam heat pump for distillation in the UK was installed in a malt whisky distillery in 1987. Novel aspects of the system are modifications to the batch process to enable continuous and efficient operation of the heat pump across a number of stills, the use of steam in a closed cycle and compression of the steam by a twin-screw compressor. The heat pump is incorporated into the distillery steam distribution system operating in parallel with the existing boiler, allowing complete flexibility of operation. The installation demonstrates the large primary energy savings that can be achieved by the optimisation of integrated heat pumps in batch processes. The principle and much of the system design could be applied to continuous distillation processes and to other batch operations such as drying, steam stripping and solvent recovery. In this paper a steam heat pump is described which has been installed in the Auchroisk malt whisky distillery of International Distillers and Vintners Ltd (IDV). It is a result of a four year R and D programme at EA Technology Ltd. 7 figs., 3 refs.

  18. Um framework de elaboração de persona empresa para suporte na análise de valor de negócio na aplicação em sistemas de redes sociais

    OpenAIRE

    Nobrega, Carlos Lenine de Oliveira

    2011-01-01

    Este trabalho apresenta um estudo realizado para conhecimento dos usuários de perfis de redes sociais criados no twitter, envolvidos nas questões de trânsito e meio ambiente. Tal conhecimento permite manter o sucesso contínuo da rede, pois possibilita direcionar o perfil da rede para os interesses de seus usuários, gerando oportunidades para a realização de negócios. As técnicas de conhecimento dos usuários usadas foram o uso de um framework de elaboração de Personas, aplicação de question...

  19. Cadeia de valor de megaeventos: um estudo de caso de uma feira de negócios agropecuários

    Directory of Open Access Journals (Sweden)

    Fabrício Silva Barbosa

    2015-01-01

    Full Text Available O turismo de eventos definitivamente consolidou-se como uma das ramificações do turismo que mais favorecem o desenvolvimento econômico das localidades onde se realizam. No Brasil, a prática de megaeventos impulsiona o segmento e alavanca o setor de serviços que atua na localidade. Contudo, para que atendam às expectativas de seus organizadores, alguns processos necessitam ser introduzidos de forma adequada. A cadeia de valor aparece como uma ferramenta indispensável nas suas realizações. Este artigo teve como objetivo analisar a Feira de Negócios Agropecuários da Fronteira Oeste – Fenaoeste, realizada em São Borja/RS - Brasil, tomando como base a cadeia de valor porteriana com uma adaptação das suas atividades primárias e secundárias com as lentes de serviços. De caráter qualitativo e exploratório, o trabalho teve como método um estudo de caso. Com base nas entrevistas com os especialistas e na literatura da área, apresentam-se pontos e questões estratégicos para a competitividade de megaeventos, em que os aspectos ligados à tecnologia de informações e ao envolvimento dos clientes internos e externos têm intensas influências. Para melhoria das atividades na busca de vantagens competitivas, sugere-se um uso mais intenso de tecnologia de informações principalmente no pós-evento, em que existe maior necessidade da interação humana com os clientes, que são coprodutores, para obtenção de conhecimento sobre estas partes interessadas. Para tanto, deve-se coordenar os aspectos de intangibilidade, perecibilidade e simultaneidade com atenção em pontos como treinamentos, divulgação do evento, riscos de contratação, sistemas de gestão e terceirização dos funcionários (com cuidado aos estratégicos para promover produtos essenciais dos eventos: qualidade de serviços, experiência do cliente e show. A universidade pode ajudar neste desenvolvimento. Ainda que esta pesquisa não seja de caráter conclusivo, s

  20. Method for controlling powertrain pumps

    Science.gov (United States)

    Sime, Karl Andrew; Spohn, Brian L; Demirovic, Besim; Martini, Ryan D; Miller, Jean Marie

    2013-10-22

    A method of controlling a pump supplying a fluid to a transmission includes sensing a requested power and an excess power for a powertrain. The requested power substantially meets the needs of the powertrain, while the excess power is not part of the requested power. The method includes sensing a triggering condition in response to the ability to convert the excess power into heat in the transmission, and determining that an operating temperature of the transmission is below a maximum. The method also includes determining a calibrated baseline and a dissipation command for the pump. The calibrated baseline command is configured to supply the fluid based upon the requested power, and the dissipation command is configured to supply additional fluid and consume the excess power with the pump. The method operates the pump at a combined command, which is equal to the calibrated baseline command plus the dissipation command.

  1. High Performance Space Pump Project

    Data.gov (United States)

    National Aeronautics and Space Administration — PDT is proposing a High Performance Space Pump based upon an innovative design using several technologies. The design will use a two-stage impeller, high temperature...

  2. Heat pumps at the maltings

    Energy Technology Data Exchange (ETDEWEB)

    1987-11-01

    Heat pumps have halved the energy costs of producing finished malt at two of the country's maltsters. The fuel-fired kilning processes described are now performed by heat pumps with considerable energy and production benefits at the maltings of J.P. Simpson and Co. (Alnwick) Ltd, in Tivetshall St Margaret, Norfolk, and of Munton and Fison Plc of Stowmarket, Suffolk. The heat pump system installed at the Station Malting of J.P. Simpson was devised by the Electricity Council Research Centre at Capenhurst near Chester. Energy cost benefits of Pound 6,000 a month are being realised at Simpsons, but there is the added benefit that the system has been designed to provide conditioned air to the germination cycle to ensure that the correct temperature is maintained throughout the year. At the Cedars factory of Munton and Fison, heat pumps were used on a trial basis for plant micropropagation and for a fish farming unit.

  3. Magnetic heat pump flow director

    Science.gov (United States)

    Howard, Frank S. (Inventor)

    1995-01-01

    A fluid flow director is disclosed. The director comprises a handle body and combed-teeth extending from one side of the body. The body can be formed of a clear plastic such as acrylic. The director can be used with heat exchangers such as a magnetic heat pump and can minimize the undesired mixing of fluid flows. The types of heat exchangers can encompass both heat pumps and refrigerators. The director can adjust the fluid flow of liquid or gas along desired flow directions. A method of applying the flow director within a magnetic heat pump application is also disclosed where the comb-teeth portions of the director are inserted into the fluid flow paths of the heat pump.

  4. Transverse pumped laser amplifier architecture

    Science.gov (United States)

    Bayramian, Andrew James; Manes, Kenneth; Deri, Robert; Erlandson, Al; Caird, John; Spaeth, Mary

    2013-07-09

    An optical gain architecture includes a pump source and a pump aperture. The architecture also includes a gain region including a gain element operable to amplify light at a laser wavelength. The gain region is characterized by a first side intersecting an optical path, a second side opposing the first side, a third side adjacent the first and second sides, and a fourth side opposing the third side. The architecture further includes a dichroic section disposed between the pump aperture and the first side of the gain region. The dichroic section is characterized by low reflectance at a pump wavelength and high reflectance at the laser wavelength. The architecture additionally includes a first cladding section proximate to the third side of the gain region and a second cladding section proximate to the fourth side of the gain region.

  5. Performance studies of the CMS Strip Tracker before installation

    Energy Technology Data Exchange (ETDEWEB)

    Adam, W.; et al.

    2009-06-01

    In March 2007 the assembly of the Silicon Strip Tracker was completed at the Tracker Integration Facility at CERN. Nearly 15% of the detector was instrumented using cables, fiber optics, power supplies, and electronics intended for the operation at the LHC. A local chiller was used to circulate the coolant for low temperature operation. In order to understand the efficiency and alignment of the strip tracker modules, a cosmic ray trigger was implemented. From March through July 4.5 million triggers were recorded. This period, referred to as the Sector Test, provided practical experience with the operation of the Tracker, especially safety, data acquisition, power, and cooling systems. This paper describes the performance of the strip system during the Sector Test, which consisted of five distinct periods defined by the coolant temperature. Significant emphasis is placed on comparisons between the data and results from Monte Carlo studies.

  6. Efficiency measurements for 3D silicon strip detectors

    Energy Technology Data Exchange (ETDEWEB)

    Parzefall, Ulrich, E-mail: ulrich.parzefall@physik.uni-freiburg.d [Physikalisches Institut, Universitaet Freiburg, Hermann-Herder-Str. 3, D-79104 Freiburg (Germany); Dalla Betta, Gian-Franco [INFN Trento and Universita di Trento, via Sommarive 14, 38050 Povo di Trento (Italy); Boscardin, Maurizio [FBK-irst, Center for Materials and Microsystems, via Sommarive 18, 38050 Povo di Trento (Italy); Eckert, Simon [Physikalisches Institut, Universitaet Freiburg, Hermann-Herder-Str. 3, D-79104 Freiburg (Germany); Eklund, Lars; Fleta, Celeste [University of Glasgow, Department of Physics and Astronomy, Glasgow G12 8QQ (United Kingdom); Jakobs, Karl; Koehler, Michael; Kuehn, Susanne; Pahn, Gregor [Physikalisches Institut, Universitaet Freiburg, Hermann-Herder-Str. 3, D-79104 Freiburg (Germany); Parkes, Chris; Pennicard, David [University of Glasgow, Department of Physics and Astronomy, Glasgow G12 8QQ (United Kingdom); Ronchin, Sabina [FBK-irst, Center for Materials and Microsystems, via Sommarive 18, 38050 Povo di Trento (Italy); Zoboli, Andrea [INFN Trento and Universita di Trento, via Sommarive 14, 38050 Povo di Trento (Italy); Zorzi, Nicola [FBK-irst, Center for Materials and Microsystems, via Sommarive 18, 38050 Povo di Trento (Italy)

    2010-11-01

    Silicon strip detectors are widely used as part of the inner tracking layers in particle physics experiments. For applications at the luminosity upgrade of the Large Hadron Collider (LHC), the sLHC, silicon detectors with extreme radiation hardness are required. The 3D detector design, where electrodes are processed from underneath the strips into the silicon bulk material, provides a way to enhance the radiation tolerance of standard planar silicon strip detectors. Detectors with several innovative 3D designs that constitute a simpler and more cost-effective processing than the 3D design initially proposed were connected to read-out electronics from LHC experiments and subsequently tested. Results on the amount of charge collected, the noise and the uniformity of charge collection are given.

  7. Analytical possibilities of microelectrode use for stripping voltammetry

    Energy Technology Data Exchange (ETDEWEB)

    Matysik, F.M. (Leipzig Univ. (Germany). Dept. of Chemistry); Glaeser, P. (Leipzig Univ. (Germany). Dept. of Chemistry); Werner, G. (Leipzig Univ. (Germany). Dept. of Chemistry)

    1994-07-01

    The analytical utility of microelectrodes for stripping voltammetry is discussed from several points of view. The application of microelectrodes for microanalysis is demonstrated using a novel capillary flow injection system. Heavy metals at [mu]g l[sup -1] concentrations have been determined in [mu]l-samples. The influence of electrode size and convection during the deposition period of anodic stripping voltammetry on the reproducibility of trace metal determination was studied for various types of electrodes. In the case of mercury film microelectrodes, the precision can be improved if the accumulation of the analyte is performed under quiescent conditions. Practical examples of stripping voltammetry with microelectrodes such as copper determination in whisky and trace metal measurements in drinking water are given. (orig.)

  8. Development, prototyping and characterization of double sided silicon strip detectors

    Science.gov (United States)

    Topkar, Anita; Singh, Arvind; Aggarwal, Bharti; Kumar, Amit; Kumar, Arvind; Murali Krishna, L. V.; Das, D.

    2016-10-01

    Double sided DC-coupled silicon strip detectors with geometry of 65 mm×65 mm have been developed in India for nuclear physics experiments. The detectors have 64 P+ strips on the front side and 64 N+ strips on the backside with a pitch of 0.9 mm. These detectors were fabricated using a twelve mask layer process involving double sided wafer processing technology. Semiconductor process and device simulations were carried out in order to theoretically estimate the impact of important design and process parameters on the breakdown voltage of detectors. The performance of the first lot of prototype detectors has been studied using static characterization tests and using an alpha source. The characterization results demonstrate that the detectors have low leakage currents and good uniformity over the detector area of about 40 cm2. Overview of the detector design, fabrication process, simulation results and initial characterization results of the detectors are presented in this paper.

  9. A Hybrid Algorithm for Strip Packing Problem with Rotation Constraint

    Directory of Open Access Journals (Sweden)

    Chen Huan

    2016-01-01

    Full Text Available Strip packing is a well-known NP-hard problem and it was widely applied in engineering fields. This paper considers a two-dimensional orthogonal strip packing problem. Until now some exact algorithm and mainly heuristics were proposed for two-dimensional orthogonal strip packing problem. While this paper proposes a two-stage hybrid algorithm for it. In the first stage, a heuristic algorithm based on layering idea is developed to construct a solution. In the second stage, a great deluge algorithm is used to further search a better solution. Computational results on several classes of benchmark problems have revealed that the hybrid algorithm improves the results of layer-heuristic, and can compete with other heuristics from the literature.

  10. Nonlinear Vibration Analysis of Moving Strip with Inertial Boundary Condition

    Directory of Open Access Journals (Sweden)

    Chong-yi Gao

    2015-01-01

    Full Text Available According to the movement mechanism of strip and rollers in tandem mill, the strip between two stands was simplified to axially moving Euler beam and the rollers were simplified to the inertial component on the fixed axis rotation, namely, inertial boundary. Nonlinear vibration mechanical model of Euler beam with inertial boundary conditions was established. The transverse and longitudinal motion equations were derived based on Hamilton’s principle. Kantorovich averaging method was employed to discretize the motion equations and the inertial boundary equations, and the solutions were obtained using the modified iteration method. Depending on numerical calculation, the amplitude-frequency responses of Euler beam were determined. The axial velocity, tension, and rotational inertia have strong influences on the vibration characteristics. The results would provide an important theoretical reference to control and analyze the vertical vibration of moving strip in continuous rolling process.

  11. Performance studies of the CMS Strip Tracker before installation

    CERN Document Server

    Adam, Wolfgang; Dragicevic, Marko; Friedl, Markus; Fruhwirth, R; Hansel, S; Hrubec, Josef; Krammer, Manfred; Oberegger, Margit; Pernicka, Manfred; Schmid, Siegfried; Stark, Roland; Steininger, Helmut; Uhl, Dieter; Waltenberger, Wolfgang; Widl, Edmund; Van Mechelen, Pierre; Cardaci, Marco; Beaumont, Willem; de Langhe, Eric; de Wolf, Eddi A; Delmeire, Evelyne; Hashemi, Majid; Bouhali, Othmane; Charaf, Otman; Clerbaux, Barbara; Dewulf, Jean-Paul; Elgammal, Sherif; Hammad, Gregory Habib; de Lentdecker, Gilles; Marage, Pierre Edouard; Vander Velde, Catherine; Vanlaer, Pascal; Wickens, John; Adler, Volker; Devroede, Olivier; De Weirdt, Stijn; D'Hondt, Jorgen; Goorens, Robert; Heyninck, Jan; Maes, Joris; Mozer, Matthias Ulrich; Tavernier, Stefaan; Van Lancker, Luc; Van Mulders, Petra; Villella, Ilaria; Wastiels, C; Bonnet, Jean-Luc; Bruno, Giacomo; De Callatay, Bernard; Florins, Benoit; Giammanco, Andrea; Gregoire, Ghislain; Keutgen, Thomas; Kcira, Dorian; Lemaitre, Vincent; Michotte, Daniel; Militaru, Otilia; Piotrzkowski, Krzysztof; Quertermont, L; Roberfroid, Vincent; Rouby, Xavier; Teyssier, Daniel; Daubie, Evelyne; Anttila, Erkki; Czellar, Sandor; Engstrom, Pauli; Harkonen, J; Karimaki, V; Kostesmaa, J; Kuronen, Auli; Lampen, Tapio; Linden, Tomas; Luukka, Panja-Riina; Maenpaa, T; Michal, Sebastien; Tuominen, Eija; Tuominiemi, Jorma; Ageron, Michel; Baulieu, Guillaume; Bonnevaux, Alain; Boudoul, Gaelle; Chabanat, Eric; Chabert, Eric Christian; Chierici, Roberto; Contardo, Didier; Della Negra, Rodolphe; Dupasquier, Thierry; Gelin, Georges; Giraud, Noël; Guillot, Gérard; Estre, Nicolas; Haroutunian, Roger; Lumb, Nicholas; Perries, Stephane; Schirra, Florent; Trocme, Benjamin; Vanzetto, Sylvain; Agram, Jean-Laurent; Blaes, Reiner; Drouhin, Frédéric; Ernenwein, Jean-Pierre; Fontaine, Jean-Charles; Berst, Jean-Daniel; Brom, Jean-Marie; Didierjean, Francois; Goerlach, Ulrich; Graehling, Philippe; Gross, Laurent; Hosselet, J; Juillot, Pierre; Lounis, Abdenour; Maazouzi, Chaker; Olivetto, Christian; Strub, Roger; Van Hove, Pierre; Anagnostou, Georgios; Brauer, Richard; Esser, Hans; Feld, Lutz; Karpinski, Waclaw; Klein, Katja; Kukulies, Christoph; Olzem, Jan; Ostapchuk, Andrey; Pandoulas, Demetrios; Pierschel, Gerhard; Raupach, Frank; Schael, Stefan; Schwering, Georg; Sprenger, Daniel; Thomas, Maarten; Weber, Markus; Wittmer, Bruno; Wlochal, Michael; Beissel, Franz; Bock, E; Flugge, G; Gillissen, C; Hermanns, Thomas; Heydhausen, Dirk; Jahn, Dieter; Kaussen, Gordon; Linn, Alexander; Perchalla, Lars; Poettgens, Michael; Pooth, Oliver; Stahl, Achim; Zoeller, Marc Henning; Buhmann, Peter; Butz, Erik; Flucke, Gero; Hamdorf, Richard Helmut; Hauk, Johannes; Klanner, Robert; Pein, Uwe; Schleper, Peter; Steinbruck, G; Blum, P; De Boer, Wim; Dierlamm, Alexander; Dirkes, Guido; Fahrer, Manuel; Frey, Martin; Furgeri, Alexander; Hartmann, Frank; Heier, Stefan; Hoffmann, Karl-Heinz; Kaminski, Jochen; Ledermann, Bernhard; Liamsuwan, Thiansin; Muller, S; Muller, Th; Schilling, Frank-Peter; Simonis, Hans-Jürgen; Steck, Pia; Zhukov, Valery; Cariola, P; De Robertis, Giuseppe; Ferorelli, Raffaele; Fiore, Luigi; Preda, M; Sala, Giuliano; Silvestris, Lucia; Tempesta, Paolo; Zito, Giuseppe; Creanza, Donato; De Filippis, Nicola; De Palma, Mauro; Giordano, Domenico; Maggi, Giorgio; Manna, Norman; My, Salvatore; Selvaggi, Giovanna; Albergo, Sebastiano; Chiorboli, Massimiliano; Costa, Salvatore; Galanti, Mario; Giudice, Nunzio; Guardone, Nunzio; Noto, Francesco; Potenza, Renato; Saizu, Mirela Angela; Sparti, V; Sutera, Concetta; Tricomi, Alessia; Tuve, Cristina; Brianzi, Mirko; Civinini, Carlo; Maletta, Fernando; Manolescu, Florentina; Meschini, Marco; Paoletti, Simone; Sguazzoni, Giacomo; Broccolo, B; Ciulli, Vitaliano; D'Alessandro, Raffaello; Focardi, Ettore; Frosali, Simone; Genta, Chiara; Landi, Gregorio; Lenzi, Piergiulio; Macchiolo, Anna; Magini, Nicolo; Parrini, Giuliano; Scarlini, Enrico; Cerati, Giuseppe Benedetto; Azzi, Patrizia; Bacchetta, Nicola; Candelori, Andrea; Dorigo, Tommaso; Kaminsky, A; Karaevski, S; Khomenkov, Volodymyr; Reznikov, Sergey; Tessaro, Mario; Bisello, Dario; De Mattia, Marco; Giubilato, Piero; Loreti, Maurizio; Mattiazzo, Serena; Nigro, Massimo; Paccagnella, Alessandro; Pantano, Devis; Pozzobon, Nicola; Tosi, Mia; Bilei, Gian Mario; Checcucci, Bruno; Fano, Livio; Servoli, Leonello; Ambroglini, Filippo; Babucci, Ezio; Benedetti, Daniele; Biasini, Maurizio; Caponeri, Benedetta; Covarelli, Roberto; Giorgi, Marco; Lariccia, Paolo; Mantovani, Giancarlo; Marcantonini, Marta; Postolache, Vasile; Santocchia, Attilio; Spiga, Daniele; Bagliesi, Giuseppe; Balestri, Gabriele; Berretta, Luca; Bianucci, S; Boccali, Tommaso; Bosi, Filippo; Bracci, Fabrizio; Castaldi, Rino; Ceccanti, Marco; Cecchi, Roberto; Cerri, Claudio; Cucoanes, Andi Sebastian; Dell'Orso, Roberto; Dobur, Didar; Dutta, Suchandra; Giassi, Alessandro; Giusti, Simone; Kartashov, Dmitry; Kraan, Aafke; Lomtadze, Teimuraz; Lungu, George-Adrian; Magazzu, Guido; Mammini, Paolo; Mariani, Filippo; Martinelli, Giovanni; Moggi, Andrea; Palla, Fabrizio; Palmonari, Francesco; Petragnani, Giulio; Profeti, Alessandro; Raffaelli, Fabrizio; Rizzi, Domenico; Sanguinetti, Giulio; Sarkar, Subir; Sentenac, Daniel; Serban, Alin Titus; Slav, Adrian; Soldani, A; Spagnolo, Paolo; Tenchini, Roberto; Tolaini, Sergio; Venturi, Andrea; Verdini, Piero Giorgio; Vos, Marcel; Zaccarelli, Luciano; Avanzini, Carlo; Basti, Andrea; Benucci, Leonardo; Bocci, Andrea; Cazzola, Ugo; Fiori, Francesco; Linari, Stefano; Massa, Maurizio; Messineo, Alberto; Segneri, Gabriele; Tonelli, Guido; Azzurri, Paolo; Bernardini, Jacopo; Borrello, Laura; Calzolari, Federico; Foa, Lorenzo; Gennai, Simone; Ligabue, Franco; Petrucciani, Giovanni; Rizzi, Andrea; Yang, Zong-Chang; Benotto, Franco; Demaria, Natale; Dumitrache, Floarea; Farano, R; Borgia, Maria Assunta; Castello, Roberto; Costa, Marco; Migliore, Ernesto; Romero, Alessandra; Abbaneo, Duccio; Abbas, M; Ahmed, Ijaz; Akhtar, I; Albert, Eric; Bloch, Christoph; Breuker, Horst; Butt, Shahid Aleem; Buchmuller, Oliver; Cattai, Ariella; Delaere, Christophe; Delattre, Michel; Edera, Laura Maria; Engstrom, Pauli; Eppard, Michael; Gateau, Maryline; Gill, Karl; Giolo-Nicollerat, Anne-Sylvie; Grabit, Robert; Honma, Alan; Huhtinen, Mika; Kloukinas, Kostas; Kortesmaa, Jarmo; Kottelat, Luc-Joseph; Kuronen, Auli; Leonardo, Nuno; Ljuslin, Christer; Mannelli, Marcello; Masetti, Lorenzo; Marchioro, Alessandro; Mersi, Stefano; Michal, Sebastien; Mirabito, Laurent; Muffat-Joly, Jeannine; Onnela, Antti; Paillard, Christian; Pal, Imre; Pernot, Jean-Francois; Petagna, Paolo; Petit, Patrick; Piccut, C; Pioppi, Michele; Postema, Hans; Ranieri, Riccardo; Ricci, Daniel; Rolandi, Gigi; Ronga, Frederic Jean; Sigaud, Christophe; Syed, A; Siegrist, Patrice; Tropea, Paola; Troska, Jan; Tsirou, Andromachi; Vander Donckt, Muriel; Vasey, François; Alagoz, Enver; Amsler, Claude; Chiochia, Vincenzo; Regenfus, Christian; Robmann, Peter; Rochet, Jacky; Rommerskirchen, Tanja; Schmidt, Alexander; Steiner, Stefan; Wilke, Lotte; Church, Ivan; Cole, Joanne; Coughlan, John A; Gay, Arnaud; Taghavi, S; Tomalin, Ian R; Bainbridge, Robert; Cripps, Nicholas; Fulcher, Jonathan; Hall, Geoffrey; Noy, Matthew; Pesaresi, Mark; Radicci, Valeria; Raymond, David Mark; Sharp, Peter; Stoye, Markus; Wingham, Matthew; Zorba, Osman; Goitom, Israel; Hobson, Peter R; Reid, Ivan; Teodorescu, Liliana; Hanson, Gail; Jeng, Geng-Yuan; Liu, Haidong; Pasztor, Gabriella; Satpathy, Asish; Stringer, Robert; Mangano, Boris; Affolder, K; Affolder, T; Allen, Andrea; Barge, Derek; Burke, Samuel; Callahan, D; Campagnari, Claudio; Crook, A; D'Alfonso, Mariarosaria; Dietch, J; Garberson, Jeffrey; Hale, David; Incandela, H; Incandela, Joe; Jaditz, Stephen; Kalavase, Puneeth; Kreyer, Steven Lawrence; Kyre, Susanne; Lamb, James; Mc Guinness, C; Mills, C; Nguyen, Harold; Nikolic, Milan; Lowette, Steven; Rebassoo, Finn; Ribnik, Jacob; Richman, Jeffrey; Rubinstein, Noah; Sanhueza, S; Shah, Yousaf Syed; Simms, L; Staszak, D; Stoner, J; Stuart, David; Swain, Sanjay Kumar; Vlimant, Jean-Roch; White, Dean; Ulmer, Keith; Wagner, Stephen Robert; Bagby, Linda; Bhat, Pushpalatha C; Burkett, Kevin; Cihangir, Selcuk; Gutsche, Oliver; Jensen, Hans; Johnson, Mark; Luzhetskiy, Nikolay; Mason, David; Miao, Ting; Moccia, Stefano; Noeding, Carsten; Ronzhin, Anatoly; Skup, Ewa; Spalding, William J; Spiegel, Leonard; Tkaczyk, Slawek; Yumiceva, Francisco; Zatserklyaniy, Andriy; Zerev, E; Anghel, Ioana Maria; Bazterra, Victor Eduardo; Gerber, Cecilia Elena; Khalatian, S; Shabalina, Elizaveta; Baringer, Philip; Bean, Alice; Chen, Jie; Hinchey, Carl Louis; Martin, Christophe; Moulik, Tania; Robinson, Richard; Gritsan, Andrei; Lae, Chung Khim; Tran, Nhan Viet; Everaerts, Pieter; Hahn, Kristan Allan; Harris, Philip; Nahn, Steve; Rudolph, Matthew; Sung, Kevin; Betchart, Burton; Demina, Regina; Gotra, Yury; Korjenevski, Sergey; Miner, Daniel Carl; Orbaker, Douglas; Christofek, Leonard; Hooper, Ryan; Landsberg, Greg; Nguyen, Duong; Narain, Meenakshi; Speer, Thomas; Tsang, Ka Vang

    2009-01-01

    In March 2007 the assembly of the Silicon Strip Tracker was completed at the Tracker Integration Facility at CERN. Nearly 15% of the detector was instrumented using cables, fiber optics, power supplies, and electronics intended for the operation at the LHC. A local chiller was used to circulate the coolant for low temperature operation. In order to understand the efficiency and alignment of the strip tracker modules, a cosmic ray trigger was implemented. From March through July 4.5 million triggers were recorded. This period, referred to as the Sector Test, provided practical experience with the operation of the Tracker, especially safety, data acquisition, power, and cooling systems. This paper describes the performance of the strip system during the Sector Test, which consisted of five distinct periods defined by the coolant temperature. Significant emphasis is placed on comparisons between the data and results from Monte Carlo studies.

  12. Fast image retargeting based on strip dividing and resizing

    Institute of Scientific and Technical Information of China (English)

    Shungang Hua; Honglei Wei; Tieming Su

    2014-01-01

    Based on image strip dividing, an effective and fast image retargeting algorithm is proposed for resizing images. First, we construct the image energy map using gradient magnitude of the pixels and calculate the accumulated energy of each column, dividing the image into several strips by integrating similar energy columns. The reduced amount of dimension is decided in inverse proportion to the average energy for each strip. Then we retar-get the image combining scaling with cropping in terms of each strip’s reduced ratio. Experiment results show that the proposed algorithm is capable of implementing fast image retargeting and preserving both the local structures and the global visual effect of the image.

  13. Thermoviscoelastic dynamic response for a composite material thin narrow strip

    Energy Technology Data Exchange (ETDEWEB)

    Dai, Hong Liang; Qi, Li-Li; Liu, Hai-Bo [Hunan University, Changsha (China)

    2015-02-15

    Based on von Karman nonlinear strain-displacement relationships and classical thin plate theory, a list of nonlinear dynamic equilibrium equations for a viscoelastic composite material thin narrow strip under thermal and mechanic loads are deduced. According to the material constitutive relationship and the relaxation modulus in the form of the Prony series, combing with the Newmark method and the Newton-cotes integration method, a new numerical algorithm for direct solving the whole problem in the time domain is established. By applying this numerical algorithm, the viscoelastic composite material thin narrow strip as the research subject is analyzed systematically, and its rich dynamical behaviors are revealed comprehensively. To verify the accuracy of the present work, a comparison is made with previously published results. Finally, the viscoelastic composite material thin narrow strip under harmonic excitation load and impact load are discussed in detail, and many valuable thermoviscoelastic dynamic characteristics are revealed.

  14. Manganese detection in marine sediments: anodic vs. cathodic stripping voltammetry.

    Science.gov (United States)

    Banks, Craig E; Kruusma, Jaanus; Moore, Ryan R; Tomcík, Peter; Peters, Judith; Davis, James; Komorsky-Lovrić, Sebojka; Compton, Richard G

    2005-01-30

    Three different electroanalytical techniques for the detection of manganese in marine sediments are evaluated. The anodic stripping voltammetry of manganese at an in situ bismuth-film-modified boron-doped diamond electrode and cathodic stripping voltammetry at a carbon paste electrode are shown to lack the required sensitivity and reproducibility whereas cathodic stripping voltammetry at a bare boron-doped diamond electrode is shown to be reliable and selective with a limit of detection, from applying a 60s accumulation period of 7.4 x 10(-7)M and a sensitivity of 0.24AM(-1). The method was used to evaluate the manganese content of marine sediments taken from Sibenik, Croatia.

  15. Pump control system for windmills

    Science.gov (United States)

    Avery, Don E.

    1983-01-01

    A windmill control system having lever means, for varying length of stroke of the pump piston, and a control means, responsive to the velocity of the wind to operate the lever means to vary the length of stroke and hence the effective displacement of the pump in accordance with available wind energy, with the control means having a sensing member separate from the windmill disposed in the wind and displaceable thereby in accordance with wind velocity.

  16. Diode-pumped dye laser

    Science.gov (United States)

    Burdukova, O. A.; Gorbunkov, M. V.; Petukhov, V. A.; Semenov, M. A.

    2016-10-01

    This letter reports diode pumping for dye lasers. We offer a pulsed dye laser with an astigmatism-compensated three-mirror cavity and side pumping by blue laser diodes with 200 ns pulse duration. Eight dyes were tested. Four dyes provided a slope efficiency of more than 10% and the highest slope efficiency (18%) was obtained for laser dye Coumarin 540A in benzyl alcohol.

  17. Optical Pumping of Molecular Gases

    Science.gov (United States)

    1976-04-01

    in Hg, excimer system. IV. OPTICALLY PUMPED Na Ř The details of our optical pumping studies of Na2 are presented in Appendix I. The study showed that...inversitot In IM -Second set of linesn have. tentatively been Identified ats D asid A btuu~t-sa A-band tratsitiwts termiuiatitig, oilt*n 3,4,5 for J0 TO HELIUM

  18. 33 CFR 183.524 - Fuel pumps.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Fuel pumps. 183.524 Section 183... SAFETY BOATS AND ASSOCIATED EQUIPMENT Fuel Systems Equipment Standards § 183.524 Fuel pumps. (a) Each diaphragm pump must not leak fuel from the pump if the primary diaphragm fails. (b) Each...

  19. 14 CFR 29.991 - Fuel pumps.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel pumps. 29.991 Section 29.991... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Powerplant Fuel System Components § 29.991 Fuel pumps. (a) Compliance with § 29.955 must not be jeopardized by failure of— (1) Any one pump except pumps that...

  20. 46 CFR 181.300 - Fire pumps.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Fire pumps. 181.300 Section 181.300 Shipping COAST GUARD... EQUIPMENT Fire Main System § 181.300 Fire pumps. (a) A self priming, power driven fire pump must be..., the minimum capacity of the fire pump must be 189 liters (50 gallons) per minute at a pressure of...

  1. 14 CFR 27.991 - Fuel pumps.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel pumps. 27.991 Section 27.991... STANDARDS: NORMAL CATEGORY ROTORCRAFT Powerplant Fuel System Components § 27.991 Fuel pumps. Compliance with § 27.955 may not be jeopardized by failure of— (a) Any one pump except pumps that are approved...

  2. 46 CFR 182.520 - Bilge pumps.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Bilge pumps. 182.520 Section 182.520 Shipping COAST...) MACHINERY INSTALLATION Bilge and Ballast Systems § 182.520 Bilge pumps. (a) A vessel must be provided with bilge pumps in accordance with Table 182.520(a). A second power pump is an acceptable alternative to...

  3. 46 CFR 105.20-10 - Pumps.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Pumps. 105.20-10 Section 105.20-10 Shipping COAST GUARD... DISPENSING PETROLEUM PRODUCTS Specific Requirements-Cargo Tanks § 105.20-10 Pumps. (a) Pumps for cargo... discharge side of pump if the pressure under shutoff conditions exceeds 60 pounds. When a relief valve...

  4. 14 CFR 25.991 - Fuel pumps.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Fuel pumps. 25.991 Section 25.991... STANDARDS: TRANSPORT CATEGORY AIRPLANES Powerplant Fuel System Components § 25.991 Fuel pumps. (a) Main pumps. Each fuel pump required for proper engine operation, or required to meet the fuel...

  5. 46 CFR 118.300 - Fire pumps.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Fire pumps. 118.300 Section 118.300 Shipping COAST GUARD... Fire pumps. (a) A self priming, power driven fire pump must be installed on each vessel. (b) On a..., the fire pump must be capable of delivering a single hose stream from the highest hydrant, through...

  6. 46 CFR 169.559 - Fire pumps.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Fire pumps. 169.559 Section 169.559 Shipping COAST GUARD... Firefighting Equipment Firefighting Equipment § 169.559 Fire pumps. (a) Each sailing school vessel must be equipped with fire pumps as required in Table 169.559(a). Table 169.559(a)—Fire Pumps Length Exposed...

  7. METHOD FOR OPTIMIZING THE ENERGY OF PUMPS

    NARCIS (Netherlands)

    Skovmose Kallesøe, Carsten; De Persis, Claudio

    2013-01-01

    The device for energy-optimization on operation of several centrifugal pumps controlled in rotational speed, in a hydraulic installation, begins firstly with determining which pumps as pilot pumps are assigned directly to a consumer and which pumps are hydraulically connected in series upstream of t

  8. Method for optimising the energy of pumps

    NARCIS (Netherlands)

    Skovmose Kallesøe, Carsten; De Persis, Claudio

    2011-01-01

    The method involves determining whether pumps (pu1, pu5) are directly assigned to loads (v1, v3) as pilot pumps (pu2, pu3) and hydraulically connected upstream of the pilot pumps. The upstream pumps are controlled with variable speed for energy optimization. Energy optimization circuits are selected

  9. Distillation and Air Stripping Designs for the Lunar Surface

    Science.gov (United States)

    Boul, Peter J.; Lange, Kevin E.; Conger, Bruce; Anderson, Molly

    2009-01-01

    Air stripping and distillation are two different gravity-based methods, which may be applied to the purification of wastewater on the lunar base. These gravity-based solutions to water processing are robust physical separation techniques, which may be advantageous to many other techniques for their simplicity in design and operation. The two techniques can be used in conjunction with each other to obtain high purity water. The components and feed compositions for modeling waste water streams are presented in conjunction with the Aspen property system for traditional stage distillation models and air stripping models. While the individual components for each of the waste streams will vary naturally within certain bounds, an analog model for waste water processing is suggested based on typical concentration ranges for these components. Target purity levels for the for recycled water are determined for each individual component based on NASA s required maximum contaminant levels for potable water Distillation processes are modeled separately and in tandem with air stripping to demonstrate the potential effectiveness and utility of these methods in recycling wastewater on the Moon. Optimum parameters such as reflux ratio, feed stage location, and processing rates are determined with respect to the power consumption of the process. Multistage distillation is evaluated for components in wastewater to determine the minimum number of stages necessary for each of 65 components in humidity condensate and urine wastewater mixed streams. Components of the wastewater streams are ranked by Henry s Law Constant and the suitability of air stripping in the purification of wastewater in terms of component removal is evaluated. Scaling factors for distillation and air stripping columns are presented to account for the difference in the lunar gravitation environment. Commercially available distillation and air stripping units which are considered suitable for Exploration Life Support

  10. High speed twin roll caste for aluminum alloy thin strip

    Directory of Open Access Journals (Sweden)

    T. Haga

    2007-09-01

    Full Text Available Purpose: In the present study, effectiveness of a high-speed twin roll caster for recycling aluminum alloy was investigated.Design/methodology/approach: The effects of the high-speed twin roll caster on alleviating the deterioration of mechanical properties by impurities were investigated. Properties of the cast strip were investigated by metalography, a tension test, and a bending test.Findings: A vertical type twin roll caster for strip casting of aluminum alloys was devised. The strip, which was thinner than 3 mm, could be cast at speeds higher than 60 m/min. Features of the twin roll casters are as below. Copper rolls were used and lubricant was not used in order to increase the casting speed. A casting nozzle was used to set the solidification length precisely. Heat transfer between melt and the roll was improved by hydrostatic pressure of the melt. Separating force was very small in order to prevent sticking of the strip to the roll. Low superheat casting was carried out in order to improve microstructure of the strip. In the present study, effectiveness of a high-speed and high-cooling rate twin roll caster of the present study for recycling aluminum alloy was investigated. Fe was added as impurity to 6063 and A356. The roll caster of the present study was useful to decrease the influence of impurity of Fe.Research limitations/implications: A high-speed twin roll caster of vertical type was designed and assembled to cast aluminum alloy thin strip.Originality/value: The results demonstrate that the high-speed twin roll caster can improve the deterioration by impurities.

  11. Silicon strip detector qualification for the CMS experiment

    Energy Technology Data Exchange (ETDEWEB)

    Kaussen, Gordon

    2008-10-06

    To provide the best spatial resolution for the particle trajectory reconstruction and a very fast readout, the inner tracking system of CMS is build up of silicon detectors with a pixel tracker in the center surrounded by a strip tracker. The silicon strip tracker consists of so-called modules representing the smallest detection unit of the tracking device. These modules are mounted on higher-level structures called shells in the tracker inner barrel (TIB), rods in the tracker outer barrel (TOB), disks in the tracker inner disks (TID) and petals in the tracker end caps (TEC). The performance of the participating two shells of the TIB, four rods of the TOB and two petals of the TEC (representing about 1% of the final strip tracker) could be studied in different magnetic fields over a period of approximately two month using cosmic muon signals. The last test before inserting the tracker in the CMS experiment was the Tracker Slice Test performed in spring/summer 2007 at the Tracker Integration Facility (TIF) at CERN after installing all subdetectors in the tracker support tube. Approximately 25% of the strip tracker +z side was powered and read out using a cosmic ray trigger built up of scintillation counters. In total, about 5 million muon events were recorded under various operating conditions. These events together with results from commissioning runs were used to study the detector response like cluster charges, signal-to-noise ratios and single strip noise behaviour as well as to identify faulty channels which turned out to be in the order of a few per mille. The performance of the silicon strip tracker during these different construction stages is discussed in this thesis with a special emphasis on the tracker end caps. (orig.)

  12. Distillation and Air Stripping Designs for the Lunar Surface

    Science.gov (United States)

    Boul, Peter J.; Lange, Kevin E.; Conger, Bruce; Anderson, Molly

    2009-01-01

    Air stripping and distillation are two different gravity-based methods, which may be applied to the purification of wastewater on the lunar base. These gravity-based solutions to water processing are robust physical separation techniques, which may be advantageous to many other techniques for their simplicity in design and operation. The two techniques can be used in conjunction with each other to obtain high purity water. The components and feed compositions for modeling waste water streams are presented in conjunction with the Aspen property system for traditional stage distillation models and air stripping models. While the individual components for each of the waste streams will vary naturally within certain bounds, an analog model for waste water processing is suggested based on typical concentration ranges for these components. Target purity levels for the for recycled water are determined for each individual component based on NASA s required maximum contaminant levels for potable water Distillation processes are modeled separately and in tandem with air stripping to demonstrate the potential effectiveness and utility of these methods in recycling wastewater on the Moon. Optimum parameters such as reflux ratio, feed stage location, and processing rates are determined with respect to the power consumption of the process. Multistage distillation is evaluated for components in wastewater to determine the minimum number of stages necessary for each of 65 components in humidity condensate and urine wastewater mixed streams. Components of the wastewater streams are ranked by Henry s Law Constant and the suitability of air stripping in the purification of wastewater in terms of component removal is evaluated. Scaling factors for distillation and air stripping columns are presented to account for the difference in the lunar gravitation environment. Commercially available distillation and air stripping units which are considered suitable for Exploration Life Support

  13. A visual strip sensor for determination of iron

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, Sanjukta A., E-mail: sanjuktaak301@gmail.com [Analytical Chemistry Division, BARC, Trombay, Mumbai 400085 (India); Thakur, Neha; Parab, Harshala J.; Pandey, Shailaja P. [Analytical Chemistry Division, BARC, Trombay, Mumbai 400085 (India); Shinde, Rakesh N.; Pandey, Ashok K. [Radiochemistry Division, BARC, Trombay, Mumbai 400085 (India); Kumar, Sangita D.; Reddy, A.V.R. [Analytical Chemistry Division, BARC, Trombay, Mumbai 400085 (India)

    2014-12-03

    Highlights: • A visual strip sensor for on-site detection of iron has been developed and made. • The sensor is easy to synthesize, portable and recyclable with shelf life >1 year. • Visual detection limit for iron using the present sensor is 50 ng mL{sup −1}. • Visual strip sensor was applied to ground water and fruit juices. - Abstract: A visual strip has been developed for sensing iron in different aqueous samples like natural water and fruit juices. The sensor has been synthesized by UV-radiation induced graft polymerization of acrylamide monomer in microporous poly(propylene) base. For physical immobilization of iron selective reagent, the in situ polymerization of acrylamide has been carried out in the presence of 1,10-phenanthroline. The loaded strip on interaction with Fe(II) in aqueous solution turned into orange red color and the intensity of the color was found to be directly proportional to the amount of Fe(II) in the aqueous sample. The minimal sensor response with naked eye was found for 50 ng mL{sup −1} of Fe in 15 min of interaction. However, as low as 20 ng mL{sup −1} Fe could be quantified using a spectrophotometer. The detection limit calculated using the 3s/S criteria, where ‘s’ is the standard deviation of the absorbance of blank reagent loaded strip and ‘S’ is the slope of the linear calibration plot, was 1.0 ng mL{sup −1}. The strip was applied to measure Fe in a variety of samples such as ground water and fruit juices.

  14. Electron beam pumped semiconductor laser

    Science.gov (United States)

    Hug, William F. (Inventor); Reid, Ray D. (Inventor)

    2009-01-01

    Electron-beam-pumped semiconductor ultra-violet optical sources (ESUVOSs) are disclosed that use ballistic electron pumped wide bandgap semiconductor materials. The sources may produce incoherent radiation and take the form of electron-beam-pumped light emitting triodes (ELETs). The sources may produce coherent radiation and take the form of electron-beam-pumped laser triodes (ELTs). The ELTs may take the form of electron-beam-pumped vertical cavity surface emitting lasers (EVCSEL) or edge emitting electron-beam-pumped lasers (EEELs). The semiconductor medium may take the form of an aluminum gallium nitride alloy that has a mole fraction of aluminum selected to give a desired emission wavelength, diamond, or diamond-like carbon (DLC). The sources may be produced from discrete components that are assembled after their individual formation or they may be produced using batch MEMS-type or semiconductor-type processing techniques to build them up in a whole or partial monolithic manner, or combination thereof.

  15. Study on increasing calculation precision and convergence speed of streamline strip element method

    Institute of Scientific and Technical Information of China (English)

    彭艳; 刘宏民

    2004-01-01

    The calculation precision and convergence speed of streamline strip element method are increased by using the method whose initial value of the exit lateral displacement is determined with strip element variation method, and the accurate tension lateral distribution model is adopted based on the original third power spline function streamline strip element method. The basic theory of the strip element method is developed. The calculated results by the improved streamline strip element method and the original streamline strip element method are compared with the measured results, showing that the calculated results of the improved method are in good agreement with the measured results.

  16. Jarvik 2000 pump technology and miniaturization.

    Science.gov (United States)

    Jarvik, Robert

    2014-01-01

    Blood-pump miniaturization has made amazing progress, reducing the pump diameter to one-tenth of the size of previous positive displacement pumps. In particular, axial-flow-pump technology allows tiny pumps running at high speeds to deliver from 2 to 10 L/min. A review of the background inventions of the Jarvik 2000 technology is presented, together with the reason that making pumps smaller than demanded by the particular application for which they are designed is counterproductive. Pump miniaturization is nearing its practical limit. The optimization of performance and patient outcomes should remain our primary design goal.

  17. Development of thermochromic strips as a water pasteurization indicator

    Institute of Scientific and Technical Information of China (English)

    Ishtiaq A. Qazi; M. Ali Awan; M. Anwar Baig

    2003-01-01

    Boiling of water, for purification, commonly practiced in the world, has many problems associated with it like danger of scalding,scaling in the vessels, removal of useful minerals and blandness of taste etc. Water can be made safe for drinking simply by heating at 65℃ for 6 minutes. A colour indicating strip was developed which changes colour from red to purple at 67℃. Use of this strip can help in pasteurizing water without the above problems and with considerable energy saving.

  18. Stability of flow over plates with porous suction strips

    Science.gov (United States)

    Reed, H. L.; Nayfeh, A. H.

    1981-01-01

    This paper addresses the stability of two-dimensional, incompressible boundary-layer flow over plates with suction through porous strips. The mean flow is calculated using linearized triple-deck, closed-form solutions. The stability results of the triple-deck theory are shown to be in good agreement with those of the interacting boundary layers. Then different configurations of number, spacing, and mass flow rate through such porous strips are analyzed and compared with nonsimilar uniform-suction stability results from the point of view of applicability to laminar flow control.

  19. High speed twin roll casting of 6016 strip

    OpenAIRE

    Haga, T.; Ikawa, M; H.Watari; S. Kumai

    2006-01-01

    Purpose: of this paper is to clear the possibility of high speed roll casting of thin aluminum alloy strip. 6016aluminum alloy is used for sheet metal of the automobile. Therefore, casting of 6016 was tried in this study.Castability and characteristics of roll cast 6016 strip were investigated.Design/methodology/approach: was a high speed twin roll caster. The high speed twin roll caster was designedto overcome the low castability of the twin roll caster.Findings: are as below. The 6016 could...

  20. High resolution cross strip anodes for photon counting detectors

    Science.gov (United States)

    Siegmund, O. H. W.; Tremsin, A. S.; Vallerga, J. V.; Abiad, R.; Hull, J.

    2003-05-01

    A new photon counting, imaging readout for microchannel plate sensors, the cross strip (XS) anode, has been investigated. Charge centroiding of signals detected on two orthogonal layers of sense strip sets are used to derive photon locations. The XS anode spatial resolution (<3 μm FWHM) exceeds the spatial resolution of most direct charge sensing anodes, and does so at low gain (<2×10 6). The image linearity and fidelity are high enough to resolve and map 7 μm MCP pores, offering new possibilities for astronomical and other applications.

  1. The Las Vegas Strip as a Genuinely Invented Global Landscape

    Directory of Open Access Journals (Sweden)

    Daniel Ortega

    2004-12-01

    Full Text Available Las Vegas, Nevada, is typically recognised as a place via a single urban gesture, that gesture being Las Vegas Boulevard, which is more commonly referred to as "The Strip". In constructing a thesis around the theme, "Here or There? Interconnections between the Global and the Local", one cannot ignore the invitation to discuss globalisation and its effects on a particular local fabric. For the purpose of this text, globalisation can be thought of as what Carmona et al describe as an intricate series of events leading to the world "becoming increasingly interconnected, with centralised decision making exploiting economies of scale and standardisation" (2003: 101. The centralised decision-making process for The Strip is evident in the strategy to develop individually themed casino resorts along Las Vegas Boulevard that respond to a competitive economy, thus creating a newly standardised landscape. If we also understand that globalisation can be thought of as the development of an interconnected world where economic, political and cultural boundaries can be easily crossed, this work can begin to define how the Las Vegas Strip is a genuinely invented global landscape. This paper addresses the "here-ness" as well as the "there-ness" of The Strip, while offering a dialectical framework for establishing a meaning of place by having 'there' placed 'here'. By employing semiological interpretations of real landscapes from around the globe (for example, Venturi et al, 1972, The Strip becomes a newly invented landscape of "simulations" (Baudrillard, 1988. As such, The Strip acts as a narrative that forms a unique place, opening the door to questions of authenticity and identity. This paper concludes by focusing on the question of "Here or There?" as an appropriate deviation from the assumed role that the post-modern landscape of the Las Vegas Strip plays. This work is intended to be a point of departure from the frequent criticism of the Las Vegas Strip as

  2. A plane mirror experiment inspired by a comic strip

    Science.gov (United States)

    Lúcio Prados Ribeiro, Jair

    2016-01-01

    A comic strip about a plane mirror was used in a high school optics test, and it was perceived that a large portion of the students believed that the mirror should be larger than the object so the virtual image could be entirely visible. Inspired on the comic strip, an experimental demonstration with flat mirrors was developed, in order to readdress this topic learning. Students were encouraged to create their own investigation of the phenomenon with a simple instrumental apparatus and also suggest different experimental approaches.

  3. Application of Adaptive Threading Technique to Hot Strip Mill

    Institute of Scientific and Technical Information of China (English)

    DING Jing-guo; HU Xian-lei; JIAO Jing-min; SHE Guang-fu; LIU Xiang-hua

    2008-01-01

    Thickness deviation of hot strip rolling needs to be strictly controlled in the computer system.An adaptive threading technique was researched,in which the measured data from threaded stands were used to predict thickness and material hardness errors,to modify the setup for the remaining unthreaded stands.After the adaptive threading model was used online on the hot strip mill of the Panzhihua Iron and Steel Group Co Ltd,the thickness deviation was decreased obviously.The hit rate of thickness control of different steel grades increases.

  4. Beam test of CSES silicon strip detector module

    Science.gov (United States)

    Zhang, Da-Li; Lu, Hong; Wang, Huan-Yu; Li, Xin-Qiao; Xu, Yan-Bing; An, Zheng-Hua; Yu, Xiao-xia; Wang, Hui; Shi, Feng; Wang, Ping; Zhao, Xiao-Yun

    2017-05-01

    The silicon-strip tracker of the China Seismo-Electromagnetic Satellite (CSES) consists of two double-sided silicon strip detectors (DSSDs) which provide incident particle tracking information. A low-noise analog ASIC VA140 was used in this study for DSSD signal readout. A beam test on the DSSD module was performed at the Beijing Test Beam Facility of the Beijing Electron Positron Collider (BEPC) using a 400-800 MeV/c proton beam. The pedestal analysis results, RMSE noise, gain correction, and intensity distribution of incident particles of the DSSD module are presented. Supported by the XXX Civil Space Programme

  5. Optical Möbius strips and twisted ribbon cloaks.

    Science.gov (United States)

    Freund, Isaac

    2014-02-15

    Optical Möbius strips that surround points of circular polarization, C points, in a generic three-dimensional optical field are cloaked by lines of twisted ribbons attached to the C points. When cloaking occurs, the observable signed twist index that counts the number of half-twists (one or three), and also measures the handedness (right or left), of a generic Möbius strip is determined by the twisted ribbon cloaks. Although some cloaks can be detached, they can never all be removed.

  6. Simulated Performance of a Strip-Based Upgraded VELO

    CERN Document Server

    Bird, T; Coutinho, R; Eklund, L; Ferro-Luzzi, M; Hutchcroft, D; Hynds, D; Latham, T; Schindler, H

    2014-01-01

    In order to evaluate the expected performance of an upgraded Vertex Locator based on silicon-strip sensors, two different sensor layouts and two different thermo-mechanical module designs were implemented in the LHCb simulation framework. In this note, the digitisation, clustering and track reconstruction algorithms are described, and the simulated performance, at beam conditions corresponding to instantaneous luminosities of 1 and 2$\\times 10^{33} cm^{−2}s^{−1}$, is compared to that of the current Vertex Locator. Results are presented on the material budget, strip and cluster occupancies, tracking efficiencies as well as on primary vertex, impact parameter and decay time resolutions.

  7. Beam test of CSES silicon strip detector module

    CERN Document Server

    Zhang, Da-Li; Wang, Huan-Yu; Li, Xin-Qiao; Xu, Yan-Bing; An, heng-Hua; Yu, Xiao-xia; Wang, Hui; Shi, Feng; Wang, Ping; Zhao, Xiao-Yun

    2016-01-01

    The silicon-strip tracker of China Seismo-Electromagnetic Satellite (CSES) consists of two double-sided silicon strip detectors (DSSD). It provides the tracking information of incident particles. The low-noise analog ASIC VA140 was used for signal readout of DSSD. A beam test of the DSSD module was performed in the Beijing test beam Facility of the Beijing Electron Positron Collider (BEPC) using proton beam of 400~800MeV/c. Results on pedestal analysis, RMSE noise, gain correction and reconstruction of incident position of DSSD module are presented.

  8. Ultra-stripped supernovae and double neutron star systems

    CERN Document Server

    Tauris, Thomas

    2015-01-01

    The evolution of close-orbit progenitor binaries of double neutron star (DNS) systems leads to supernova (SN) explosions of ultra-stripped stars. The amount of SN ejecta mass is very limited from such, more or less, naked metal cores with envelope masses of only 0.01-0.2 Msun. The combination of little SN ejecta mass and the associated possibility of small NS kicks is quite important for the characteristics of the resulting DNS systems left behind. Here, we discuss theoretical predictions for DNS systems, based on Case BB Roche-lobe overflow prior to ultra-stripped SNe, and briefly compare with observations.

  9. Anatomic and radiologic correlations in spontaneous hematomas of the rectus abdomninis muscles; Correlazioni anatomo-radiologiche negli ematomi spontanei dei muscoli retti dell'addome

    Energy Technology Data Exchange (ETDEWEB)

    Cavagna, E.; Carubia, G.; Schiavon, F. [Ospedale di S. Martino, Unita' Operativa Autonoma di Radiologia, Belluno (Italy)

    2000-06-01

    findings and explains the reason why most hematomas are found in the lower third of the muscle. The diagnosis, whether clinical or based on imaging findings, needs accurate pathoanatomic knowledge of the anterior abdominal wall. Once the diagnosis has been confirmed (by US or CT) patients should be treated conservatively as those that are operated are at risk of developing complications, mainly hemorrhagic. [Italian] Gli ematomi spontanei dei muscoli retti dell'addome sono frequenti ma talvolta misconosciuti nei pazienti con diatesi emorragiche, in terapia anticoagulante, negli emodializzati, negli anziani. La localizzazione di gran lunga piu' frequente e' nei quadranti inferiori dell'addome. Scopo del presente lavoro - partendo dalla descrizione della peculiare anatomia della parete addominale, in particolare della linea arcuata o semicircolare di Douglas - e' di interpretarne il motivo correlando i quadri anatomici con i rilievi TC. Il muscolo retto dell'addome e' compreso fra le aponevrosi dei muscoli obliqui e trasverso che formano la cosiddetta guaina del retto. Tale disposizione si riscontra dall'arcata costale fino a meta' distanza fra l'ombelico e la sinfisi publica, ove la lamina posteriore della guaina del retto termina con un margine ricurvo, detto linea semicircolare di Douglas. Al di sotto di questa linea le aponevrosi dei tre muscoli passano davanti al retto che si ritrova separato dal peritoneo solo per l'interposizione della fascia trasversale, sottile strato connettivale interposto tra il retto e il tessuto adiposo preperitoneale. Nella regione addominale inferiore l'arteria epigrastrica inferiore e i suoi rami perforanti, decorrendo liberi nel cellulare lasso preperitoneale possono, rompendosi, provocare un vasto ematoma. Dal 1995 al 1999 sono stati osservati 11 casi di ematoma spontaneo dei muscoli retti dell'addome: tutti i pazienti sono giunti allo studio ecografico per la rapida

  10. Comparison of solar powered water pumping systems which use diaphragm pumps

    Science.gov (United States)

    Four solar photovoltaic (PV) powered diaphragm pumps were tested at different simulated pumping depths at the USDA-ARS Conservation and Production Research Laboratory near Bushland, Texas. Two of the pumps were designed for intermediate pumping depths (30 to 70 meters), and the other two pumps were...

  11. Measure Guideline. Replacing Single-Speed Pool Pumps with Variable Speed Pumps for Energy Savings

    Energy Technology Data Exchange (ETDEWEB)

    Hunt, A. [Building Media and the Building America Retrofit Alliance (BARA), Wilmington, DE (United States); Easley, S. [Building Media and the Building America Retrofit Alliance (BARA), Wilmington, DE (United States)

    2012-05-01

    This measure guideline evaluates potential energy savings by replacing traditional single-speed pool pumps with variable speed pool pumps, and provides a basic cost comparison between continued uses of traditional pumps verses new pumps. A simple step-by-step process for inspecting the pool area and installing a new pool pump follows.

  12. Measure Guideline: Replacing Single-Speed Pool Pumps with Variable Speed Pumps for Energy Savings

    Energy Technology Data Exchange (ETDEWEB)

    Hunt, A.; Easley, S.

    2012-05-01

    The report evaluates potential energy savings by replacing traditional single-speed pool pumps with variable speed pool pumps, and provide a basic cost comparison between continued uses of traditional pumps verses new pumps. A simple step-by-step process for inspecting the pool area and installing a new pool pump follows.

  13. A novel strip energy splitting algorithm for the fine granular readout of a scintillator strip electromagnetic calorimeter

    Energy Technology Data Exchange (ETDEWEB)

    Kotera, Katsushige, E-mail: coterra@azusa.shinshu-u.ac.jp [Department of Physics, Shinshu University, 3-1-1 Asahi, Matsumoto, Nagano 390-8621 (Japan); Jeans, Daniel [Department of Physics, Graduate School of Science, The University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-0033 (Japan); Miyamoto, Akiya [High Energy Accelerator Research Organization (KEK), 1-1 Oho, Tsukuba, Ibaraki 305-0801 (Japan); Takeshita, Tohru [Department of Physics, Shinshu University, 3-1-1 Asahi, Matsumoto, Nagano 390-8621 (Japan)

    2015-07-21

    We describe an algorithm which has been developed to extract fine granularity information from an electromagnetic calorimeter (ECAL) with strip-based readout. Such a calorimeter, based on scintillator strips, is being developed to apply particle flow reconstruction to future experiments in high energy physics. The application of this algorithm to 100 GeV hadronic jets in an ECAL with 45×5 mm{sup 2} transverse segmentation improves the energy resolution from 3.6% to 3.0%, to be compared to the resolution of 2.9% achieved by an ECAL with 5×5 mm{sup 2} segmentation. The performance can be further improved by the use of 10×10 mm{sup 2} tile-shaped layers interspersed between strip layers.

  14. Experimental Realization of a Quantum Spin Pump

    DEFF Research Database (Denmark)

    Watson, Susan; Potok, R.; M. Marcus, C.;

    2003-01-01

    We demonstrate the operation of a quantum spin pump based on cyclic radio-frequency excitation of a GaAs quantum dot, including the ability to pump pure spin without pumping charge. The device takes advantage of bidirectional mesoscopic fluctuations of pumped current, made spin......-dependent by the application of an in-plane Zeeman field. Spin currents are measured by placing the pump in a focusing geometry with a spin-selective collector....

  15. Do mainframe à nuvem: inovações, estrutura industrial e modelos de negócios nas tecnologias da informação e da comunicação

    Directory of Open Access Journals (Sweden)

    Paulo Bastos Tigre

    2013-03-01

    Full Text Available Inovações radicais nas tecnologias da informação e da comunicação (TIC abrem oportunidades para o desenvolvimento de novos modelos de negócios que, quando bem-sucedidos, acabam por alterar a própria estrutura da indústria global. A partir da revisão de mudanças estruturais ocorridas nas TIC nas últimas cinco décadas, neste artigo analisam-se a relação entre novas tecnologias, o surgimento de empresas consideradas paradigmas e seus respectivos modelos de negócios visando contribuir para o processo de formulação de estratégias empresariais e políticas públicas. O caso da empresa Google, responsável pela última onda de inovações radicais no setor, é analisado com base na recente literatura sobre a economia da informação visando exemplificar o impacto das mudanças tecnológicas no padrão de competição da indústria.

  16. Numerical modelling of micro-plasto-hydrodynamic lubrication in plane strip drawing

    DEFF Research Database (Denmark)

    Carretta, Y.; Bech, Jakob Ilsted; Legrand, N.

    2017-01-01

    methodology is validated by comparison to experimental measurements conducted in plane strip drawing. The effect of physical parameters like the drawing speed, the die angle and the strip thickness reduction is investigated. The numerical results show good agreement with experiments....

  17. Computerized Decision Support Improves Medication Review Effectiveness : An Experiment Evaluating the STRIP Assistant's Usability

    NARCIS (Netherlands)

    Meulendijk, Michiel C; Spruit, Marco R; Drenth-van Maanen, A Clara; Numans, Mattijs E; Brinkkemper, Sjaak; Jansen, Paul A F; Knol, Wilma

    BACKGROUND: Polypharmacy poses threats to patients' health. The Systematic Tool to Reduce Inappropriate Prescribing (STRIP) is a drug optimization process for conducting medication reviews in primary care. To effectively and efficiently incorporate this method into daily practice, the STRIP

  18. Computerized decision support improves medication review effectiveness: an experiment evaluating the STRIP Assistant’s usability

    NARCIS (Netherlands)

    Meulendijk, M.; Spruit, M.|info:eu-repo/dai/nl/297391879; Drenth-van Maanen, C.; Numans, M.; Brinkkemper, S.|info:eu-repo/dai/nl/07500707X; Jansen, P.; Knol, W

    2015-01-01

    Background Polypharmacy poses threats to patients’ health. The Systematic Tool to Reduce Inappropriate Prescribing (STRIP) is a drug optimization process for conducting medication reviews in primary care. To effectively and efficiently incorporate this method into daily practice, the STRIP

  19. Hardness of celluloid strip-finished or polished composite surfaces with time

    OpenAIRE

    Park, S. H.; KREJCI,Ivo; Lutz, F

    2000-01-01

    An in-vitro study revealed that a celluloid strip-finished composite surface discolored more than the polished composite surface. Thus, the celluloid strip-finished composite surface may not cure enough compared with the polished composite surface.

  20. Gas Loss by Ram Pressure Stripping and Internal Feedback From Low Mass Milky Way Satellites

    CERN Document Server

    Emerick, Andrew; Grcevich, Jana; Gatto, Andrea

    2016-01-01

    The evolution of dwarf satellites of the Milky Way is affected by the combination of ram pressure and tidal stripping, and internal feedback from massive stars. We investigate gas loss processes in the smallest satellites of the Milky Way using three-dimensional, high resolution, idealized wind tunnel simulations, accounting for gas loss through both ram pressure stripping and expulsion by supernova feedback. Using initial conditions appropriate for a dwarf galaxy like Leo T, we investigate whether or not environmental gas stripping and internal feedback can quench these low mass galaxies on the expected timescales, shorter than 2 Gyr. We find that supernova feedback contributes negligibly to the stripping rate for these low star formation rate galaxies. However, we also find that ram pressure stripping is less efficient than expected in the stripping scenarios we consider. Our work suggests that, although ram pressure stripping can eventually completely strip these galaxies, other physics is likely at play t...