Use of NDE and FM for the assessment of remaining life of steam turbines

International Nuclear Information System (INIS)

Alley, T.; Stone, R.

1988-01-01

Catastrophic failures of rotating turbine components, such as the Gallatin rotor burst in 1974 and the shrunk-on disk rupture at Hinkley Point in 1969, alerted the utility industry to the failure potential of these components. Such failures can cause severe financial loss; endanger personnel; and, in nuclear plants, damage safety related equipment. To adequately predict the remaining life of a turbine rotor requires accurate information about component flaws, material properties, future operating loads, relevant failure mechanisms, and an approach to combine this information to make an assessment of remaining life. EPRI has supported the development of improved ultrasonic test equipment for use from the rotor bore (bore-sonic examination) and a fracture mechanics based life assessment code called SAFER (Stress and Fracture Evaluation of Rotors). The EPRI NDE Center has supported the transfer of this technology to industry. This presentation deals with the NDE Center's transfer of the NDE and life assessment technology to industry and discusses a particular application by Duke Power Company at their Allen Plant, Unit 1 to extend the operating life of an IP/LP turbine. (author)

Steam generator tubing NDE performance

International Nuclear Information System (INIS)

Henry, G.; Welty, C.S. Jr.

1997-01-01

Steam generator (SG) non-destructive examination (NDE) is a fundamental element in the broader SG in-service inspection (ISI) process, a cornerstone in the management of PWR steam generators. Based on objective performance measures (tube leak forced outages and SG-related capacity factor loss), ISI performance has shown a continually improving trend over the years. Performance of the NDE element is a function of the fundamental capability of the technique, and the ability of the analysis portion of the process in field implementation of the technique. The technology continues to improve in several areas, e.g. system sensitivity, data collection rates, probe/coil design, and data analysis software. With these improvements comes the attendant requirement for qualification of the technique on the damage form(s) to which it will be applied, and for training and qualification of the data analysis element of the ISI process on the field implementation of the technique. The introduction of data transfer via fiber optic line allows for remote data acquisition and analysis, thus improving the efficiency of analysis for a limited pool of data analysts. This paper provides an overview of the current status of SG NDE, and identifies several important issues to be addressed

Composite Stress Rupture NDE Research and Development Project (Kevlar[R] and Carbon)

Science.gov (United States)

Saulsberry, Regor

2010-01-01

The objective was to develop and demonstrate nondestructive evaluation (NDE) techniques capable of assessing stress rupture related strength degradation for carbon composite pressure vessels, either in a structural health monitoring (SHM) or periodic inspection mode.

Nuclear Technology. Course 26: Nondestructive Examination (NDE) Techniques I. Module 26-5, Fundamentals of Radiography.

Science.gov (United States)

Groseclose, Richard

This fifth in a series of seven modules for a course titled Nondestructive Examination (NDE) Techniques I explains the radiographic process, from radiation source selection to equipment and specimen selection and arrangement, and film processing. The module follows a typical format that includes the following sections: (1) introduction, (2) module…

Nuclear Technology. Course 32: Nondestructive Examination (NDE) Techniques II. Module 32-4, Operation of Magnetic Particle Test Equipment.

Science.gov (United States)

Groseclose, Richard

This fourth in a series of six modules for a course titled Nondestructive Examination (NDE) Techniques II describes the specific technique variables and options which are available to the test technician, provides instructions for selecting and operating the appropriate test equipment, describes physical criteria for detectable discontinuities,…

Integration of fracture mechanics and NDE

International Nuclear Information System (INIS)

Njo, D.H.; McDonald, N.R.; Nichols, R.W.

1991-01-01

This paper addresses issues concerning the effective assessment of the structural integrity of safety related components, principally the primary system, in operating nuclear power plants. The failure mode of greatest safety concern is fracture and this is usually assessed by fracture mechanics (FM) procedures. These require the choice and application of an appropriate analytical method based on a knowledge of the materials, loading and environmental conditions, and characteristics of such defects as have been identified by non destructive examination (NDE). The paper focuses on capabilities and limitations of the NDE procedures, FM methods and other input information which must be taken into account in practical circumstances as well as some problems encountered. It concludes that an integral approach requiring mutual understanding, dialogue and cooperation among the materials, FM and NDE experts is essential for effective and reliable structural integrity assessments

NDE training activities at the EPRI NDE Center

International Nuclear Information System (INIS)

Pherigo, G.L.

1988-01-01

The three principal categories of training activity at the EPRI NDE Center are in-service inspection (ISI) training, technical skills training, and human resource development. The ISI training category, which addresses recently developed NDE technologies that are ready for field application, is divided into two areas. One area provides ongoing training and qualification service to boiling water reactor (BWR) utilities in accordance with the Coordination Plan for NRC/EPRI/BWROG Training and Qualification Activities of NDE Personnel. This plan specifically addresses the detection and sizing of intergranular stress corrosion cracking (IGSCC). The second area includes training activities for other recently developed NDE technologies. Courses in this area include weld overlay examination and advanced eddy current data analysis. The technical skills training is developed and offered to support the basic NDE technology needs of the utilities, with emphasis on utility applications. These programs are provided in direct response to generic or specific needs identified by the utility NDE community. The human resource development activities are focused on long-term utility needs through awareness programs for high schools, technical schools, and universities. These training programs are described

NDE and SHM Simulation for CFRP Composites

Science.gov (United States)

Leckey, Cara A. C.; Parker, F. Raymond

2014-01-01

Ultrasound-based nondestructive evaluation (NDE) is a common technique for damage detection in composite materials. There is a need for advanced NDE that goes beyond damage detection to damage quantification and characterization in order to enable data driven prognostics. The damage types that exist in carbon fiber-reinforced polymer (CFRP) composites include microcracking and delaminations, and can be initiated and grown via impact forces (due to ground vehicles, tool drops, bird strikes, etc), fatigue, and extreme environmental changes. X-ray microfocus computed tomography data, among other methods, have shown that these damage types often result in voids/discontinuities of a complex volumetric shape. The specific damage geometry and location within ply layers affect damage growth. Realistic threedimensional NDE and structural health monitoring (SHM) simulations can aid in the development and optimization of damage quantification and characterization techniques. This paper is an overview of ongoing work towards realistic NDE and SHM simulation tools for composites, and also discusses NASA's need for such simulation tools in aeronautics and spaceflight. The paper describes the development and implementation of a custom ultrasound simulation tool that is used to model ultrasonic wave interaction with realistic 3-dimensional damage in CFRP composites. The custom code uses elastodynamic finite integration technique and is parallelized to run efficiently on computing cluster or multicore machines.

Piping inspection activities at the EPRI NDE Center

International Nuclear Information System (INIS)

Ammirato, F.V.

1988-01-01

Intergranular stress corrosion cracking (IGSCC) in the primary system of boiling water reactors (BWRs) has been a major reliability issue in recent years. BWR pipe cracking was first reported in 1974 with a low percentage of only small-diameter lines affected. However, with increased plant operating time, the number of reported cracking incidents has risen significantly and in 1982 and 1983 included the large-diameter recirculation lines. With the advent of cracking in large-diameter piping, innovative repair remedies were developed, such as weld overlay for repair (WOR). Although these remedies are effective in extending the service life of piping, they also present challenging NDE problems. The EPRI program for improving piping examination has aimed at systematically resolving the difficulties by optimizing techniques and procedures as well as by developing field-qualified automated examination equipment. The EPRI NDE Center's role has been the evaluation and transfer of the technology necessary to address the current piping examination problems of the nuclear utility industry. These activities normally include the following: technology assessment and improvement; validation through demonstrations and field trials; technology transfer reports, workshops, training, and qualification testing; and acquisition of relevant samples. The activities of the NDE Center are discussed

NDE performance demonstration in the US nuclear power industry - applications, costs, lessons learned, and connection to NDE reliability

International Nuclear Information System (INIS)

Ammirato, F.

1997-01-01

Periodic inservice inspection (ISI) of nuclear power plant components is performed in the United States to satisfy legal commitments and to provide plant owners with reliable information for managing degradation. Performance demonstration provides credible evidence that ISI will fulfill its objectives. This paper examines the technical requirements for inspection and discusses how these technical needs are used to develop effective performance demonstration applications. NDE reliability is discussed with particular reference to its role in structural integrity assessments and its connection with performance demonstration. It is shown that the role of NDE reliability can range from very small to critical depending on the particular application and must be considered carefully in design of inspection techniques and performance demonstration programs used to qualify the inspection. Finally, the costs, benefits, and problems associated with performance demonstration are reviewed along with lessons learned from more than 15 years of performance demonstration experience in the US. (orig.)

Combining NDE and fracture mechanics by artifical intelligence expert systems techniques

International Nuclear Information System (INIS)

Mucciardi, A.N.; Riccardella, P.C.

1986-01-01

This paper reports on the development of a PC-based expert system for non-destructive evaluation. Software tools from the expert systems subfield of artificial intelligence are being used to combine both NDE and fracture mechanics algorithms into one, unified package. The system incorporates elements of computer-enhanced ultrasonic signal processing, featuring artificial intelligence learning capability, state-of-the-art fracture mechanics analytical tools, and all relevant metallurgical and design data necessary to emulate the decisions of the panel(s) of experts typically involved in generating and dispositioning NDE data

Assessment of the TRINO reactor pressure vessel integrity: theoretical analysis and NDE

Energy Technology Data Exchange (ETDEWEB)

Milella, P P; Pini, A [ENEA, Rome (Italy)

1988-12-31

This document presents the method used for the capability assessment of the Trino reactor pressure vessel. The vessel integrity assessment is divided into the following parts: transients evaluation and selection, fluence estimate for the projected end of life of the vessel, characterization of unirradiated and irradiated materials, thermal and stress analysis, fracture mechanics analysis and eventually fracture input to Non Destructive Examination (NDE). For each part, results are provided. (TEC).

The middle ground of the NDE R and D spectrum

International Nuclear Information System (INIS)

Burte, H.M.; Chimenti, D.E.; Thompson, D.O.; Thompson, R.B.

1983-01-01

This keynote talk attempts to call attention to the interdisciplinary nature of NDE (nondestructive evaluation) science and technology and introduce some approaches for fostering R and D in such a situation. The objectives of DARPA, the Air Force core program for developing a science base for NDE are described. Finally, several exploratory development programs are investigated. The needs addressed by NDE include performance demands, safety, conservation, productivity with quality, and minimization of life cycle costs. The science base for electromagnetic techniques includes eddy-current flaw interactions, inversion techniques, and probe figures-of-merit. The problem of inspection reliability is addressed, and an accept-reject methodology schematicized. A methodology for approaching the middle ground of the NDE R and D spectrum is outlined. Finally, future possibilities such as the characterization of flaws in ceramics, transducer understanding, new electromagnetic probes, and thermal wave imaging are also discussed

Re-inventing NDE as science — How student ideas will help adapt NDE to the new ecosystem of science and technology

Science.gov (United States)

Meyendorf, Norbert

2018-04-01

Industry 4.0 stands for the fourth industrial revolution that is ongoing at present. Industry 4.0 is a terminology generally used in Europe to characterize the integration of production and communication technologies, the so called "smart factory". Lowering costs and efficient in-time production will be possible for low numbers of unique parts, for example by additive manufacturing (3D printing). A significant aspect is also quality and maintainability of these sometimes unique structures and components. NDE has to follow these trends, but introduce the capability of cyber systems into the inspection and maintenance processes. The author initiated in his NDE introductory class student projects where small groups of students had to identify everyday problems that can be solved by NDE techniques and suggest technical solutions based on today's technology. The results where exiting. After discussing the ecosystem and the present situation of NDE as a science, several of these ideas were presented. Let us listen to the ideas and needs of the young generation to re-invent NDE!

Steam generator inspection activities at the EPRI NDE Center

International Nuclear Information System (INIS)

Krzywosz, K.

1988-01-01

Various types of corrosion and mechanical damage continue to affect the availability of both recirculating and once-through steam generators. Both the tube bundle and its supporting structure are affected. Intergranular attack and stress corrosion cracking (SCC) are the corrosion-assisted tube-wall damage mechanisms of most concern at this time. Fatigue cracking and fretting at antivibration bars are currently the mechanical damage forms causing most concern. Improved NDE equipment and techniques are providing better detection and characterization of adverse conditions within the steam generators and doing it at an earlier stage. This allows timely corrective action. To maintain the projected life expectancy of existing and new steam generators, remedial measures have been implemented. These measures include shot- or roto-peening, U-bend stress relief, chemical cleaning of secondary side, and sleeving of tubes. The improved NDE technology will also be instrumental in monitoring and assessing the effectiveness of the remedial measures. The revision of guidance documents for steam generator in-service inspection (ISI) is providing more relevant information to support this complex operation. A multitasked project is described that includes evaluation of steam generator tube NDE technology, transfer of this technology to utilities, and rapid response utility assistance

Proceedings of the NEA workshop on development priorities for NDE of concrete structures in nuclear plants

International Nuclear Information System (INIS)

1998-01-01

The first session's objectives of this conference were to identify the perspectives of national regulators and plant operators on what is required of NDE. The second session objectives were to provide opportunity for NDE practitioners to share experience and views on the status of development of key NDE techniques: tomographic imaging for investigation of concrete structures, four examples of modern NDE techniques applied to the investigation of nuclear and non-nuclear concrete structures and a vision of future improvements, investigating concrete structures by 3D Radar imaging and imaging using mechanical impact, synopsis NDT of concrete using ultrasonics and radar. The third session objectives were to prioritise development of NDE techniques for safety related concrete structures in nuclear installations: key conclusions from earlier sessions, proposed priorities and next steps

Neutron radiography and other NDE tests of main rotor helicopter blades

International Nuclear Information System (INIS)

Beer, F.C. de; Coetzer, M.; Fendeis, D.; Silva, A. da Costa E

2004-01-01

A few nondestructive examination (NDE) techniques are extensively being used worldwide to investigate aircraft structures for all types of defects. The detection of corrosion and delaminations, which are believed to be the major initiators of defects leading to aircraft structural failures, are addressed by various NDE techniques. In a combined investigation by means of visual inspection, X-ray radiography and shearography on helicopter main rotor blades, neutron radiography (NRad) at SAFARI-1 research reactor operated by Necsa, was performed to introduce this form of NDE testing to the South African aviation industry to be evaluated for applicability. The results of the shearography, visual inspection and NRad techniques are compared in this paper. The main features and advantages of neutron radiography, within the framework of these investigations, will be highlighted

NDE of Possible Service-Induced PWSCC in Control Rod Drive Mechanism Housings Removed from Service

International Nuclear Information System (INIS)

Cumblidge, Stephen E.; Doctor, Steven R.; Schuster, George J.; Harris, Robert V.; Crawford, Susan L.

2006-01-01

Studies being conducted at the Pacific Northwest National Laboratory (PNNL) in Richland, Washington are being performed to assess the effectiveness of nondestructive examination (NDE) techniques on removed-from-service control rod drive mechanism (CRDM) nozzles and the associated J-groove attachment welds. This work is being performed to provide information to the United States Nuclear Regulatory Commission (US NRC) on the effectiveness of NDE techniques such as ultrasonic testing (UT), eddy current testing (ET), and visual testing (VT) as related to the in-service inspection of CRDM nozzles and J-groove weldments, and to enhance the knowledge base of primary water stress corrosion cracking (PWSCC) through destructive characterization of the CRDM assemblies. The basic NDE measurements follow standard industry techniques for conducting in-service inspections of CRDM nozzles and the crown of the J-groove welds and buttering. In addition, laboratory-based NDE methods were employed to conduct inspections of the CRDM assemblies, with particular emphasis on the J-groove weld and buttering. This paper describes the NDE measurements that were employed on the two CRDMs to detect and characterize the indications and the analysis of these indications. The two CRDM assemblies were removed from service from the North Anna 2 vessel head, including the CRDM nozzle, the J-groove weld, buttering, and a portion of the ferritic head material. One nozzle contains suspected PWSCC, based on in-service inspection data; the second contains evidence suggesting through-wall leakage, although this was unconfirmed. A destructive test plan is being developed to directly characterize the indications found using nondestructive testing. The results of this destructive testing will be included when the destructive testing is completed.

Nondestructive Examination (NDE) Detection and Characterization of Degradation Precursors, Technical Progress Report for FY 2012

Energy Technology Data Exchange (ETDEWEB)

Ramuhalli, P.; Meyer, R.M.; Fricke, J.M.; Prowant, M.S.; Coble, J.B.; Griffin, J.W.; Pitman, S.G.; Dahl, M.E.; Kafentzis, T.A.; Roosendaal, T.J.

2012-09-01

The overall objective of this project was to investigate the effectiveness of nondestructive examination (NDE) technology in detecting material degradation precursors by initiating and growing cracks in selected materials and using NDE methods to measure crack precursors prior to the onset of cracking. Nuclear reactor components are subject to stresses over time that are not precisely known and that make the life expectancy of components difficult to determine. To prevent future issues with the operation of these plants because of unforeseen failure of components, NDE technology is needed that can be used to identify and quantify precursors to macroscopic degradation of materials. Some of the NDE methods being researched as possible solutions to the precursor detection problem are magnetic Barkhausen noise, nonlinear ultrasonics, acoustic emission, eddy current measurements, and guided wave technology. In FY12, the objective was to complete preliminary assessment of advanced NDE techniques for sensitivity to degradation precursors, using prototypical degradation mechanisms in laboratory-scale measurements. This present document reports on the deliverable that meets the following milestone: M3LW-12OR0402143 – Report detailing an initial demonstration on samples from the crack-initiation tests will be provided (demonstrating acceleration of the work).

Preview of the NASA NNWG NDE Sample Preparation Handbook

Science.gov (United States)

2010-01-01

This viewgraph presents a step-by-step how-to fabrication documentation of every kind of sample that is fabricated for MSFC by UA Huntsville, including photos and illustrations. The tabulation of what kind of samples are being fabricated for what NDE method, detailed instructions/documentation of the inclusion/creation of defects, detailed specifications for materials, processes, and equipment, case histories and/or experiences with the different fabrication methods and defect inclusion techniques, discussion of pitfalls and difficulties associated with sample fabrication and defect inclusion techniques, and a discussion of why certain fabrication techniques are needed as related to the specific NDE methods are included in this presentation.

NDE for the 21st century: industry 4.0 requires NDE 4.0 (Conference Presentation)

Science.gov (United States)

Meyendorf, Norbert G.

2017-04-01

Industry 4.0 stands for the fourth industrial revolution that is ongoing at present. Industry 4.0 is a terminology preferred used in Europe to characterize the integration of production and communication technologies, the so called "smart factory". The first industrial revolution was the mechanization of work. The second was mass production and the assembly line. While the third revolution was the computer integrated manufacturing. Industry 4.0 encompasses the complete networking of all industrial areas. Lowering costs and efficient in-time production will be possible also for low numbers of very unique parts for example by additive manufacturing (3D printing). A significant aspect is also quality and maintainability of these sometimes unique structures and components. NDE has to follow these trends, not only by adapting NDE techniques to the new technologies, but also introducing the capability of cyber systems into the inspection and maintenance processes. The requirements and challenges for this new technological area will be discussed. Chances for applications of new technologies and systems for NDE will be demonstrated online.

Invariance algorithms for processing NDE signals

Science.gov (United States)

Mandayam, Shreekanth; Udpa, Lalita; Udpa, Satish S.; Lord, William

1996-11-01

Signals that are obtained in a variety of nondestructive evaluation (NDE) processes capture information not only about the characteristics of the flaw, but also reflect variations in the specimen's material properties. Such signal changes may be viewed as anomalies that could obscure defect related information. An example of this situation occurs during in-line inspection of gas transmission pipelines. The magnetic flux leakage (MFL) method is used to conduct noninvasive measurements of the integrity of the pipe-wall. The MFL signals contain information both about the permeability of the pipe-wall and the dimensions of the flaw. Similar operational effects can be found in other NDE processes. This paper presents algorithms to render NDE signals invariant to selected test parameters, while retaining defect related information. Wavelet transform based neural network techniques are employed to develop the invariance algorithms. The invariance transformation is shown to be a necessary pre-processing step for subsequent defect characterization and visualization schemes. Results demonstrating the successful application of the method are presented.

Assessment of NDE for key indicators of aging cables in nuclear power plants - Interim status

Science.gov (United States)

Glass, S. W.; Ramuhalli, P.; Fifield, L. S.; Prowant, M. S.; Dib, G.; Tedeschi, J. R.; Suter, J. D.; Jones, A. M.; Good, M. S.; Pardini, A. F.; Hartman, T. S.

2016-02-01

by the U.S. Nuclear Regulatory Commission, the U.S. Department of Energy, and industry (represented by the Electric Power Research Institute), an assessment of cable NDE methods was commissioned. Technologies include both bulk electrical measurements (Tan δ, time domain reflectometry, frequency domain reflectometry (FDR), partial discharge, and other techniques) and local insulation measurement (indenter, dynamic mechanical analysis interdigital capacitance, infrared spectral measurement, etc.). This aging cable NDE program update reviews the full range of techniques but focuses on the most interesting test approaches that have a chance to be deployed in-situ, particularly including Tan δ, FDR, and ultrasound methods that have been reviewed most completely in this progress period.

Evaluation and improvement in nondestructive examination (NDE) reliability for in-service inspection of light water reactors

International Nuclear Information System (INIS)

Deffenbaugh, J.D.; Good, M.S.; Green, E.R.; Heasler, P.G.; Simonen, F.A.; Spanner, J.C.; Taylor, T.T.

1988-01-01

The evaluation and improvement of NDE Reliability for In-service Inspection (ISI) of Light Water Reactors (NDE Reliability) Program at Pacific Northwest Laboratory (PNL) was established to determine the reliability of current ISI techniques and to develop recommendations that will ensure a suitably high inspection reliability. The objectives of this NRC program are to: determine the reliability of ultrasonic ISI performed on commercial light-water reactor (LWR) primary systems; determine the impact of NDE unreliability on system safety and determine the level of inspection reliability required to ensure a suitably low failure probability using probabilistic fracture mechanics analysis; evaluate the degree of reliability improvement that could be achieved using improved and advanced NDE technique; and recommend revisions to ASME Code, Section XI, and Regulatory Requirements, based on material properties, service conditions, and NDE uncertainties, that will ensure suitably low failure probabilities. The program consists of three basic tasks: a Piping task, a Pressure Vessel task, and an Evaluation and Improvement in NDE Reliability task. The major efforts were concentrated in the Piping task and the Evaluation and Improvement in NDE Reliability task

Nondestructive examination (NDE) Reliability for Inservice Inspection of Light Water Reactors

International Nuclear Information System (INIS)

Doctor, S.R.; Good, M.S.; Heasler, P.G.; Hockey, R.L.; Simonen, F.A.; Spanner, J.C.; Taylor, T.T.; Vo, T.V.

1992-07-01

The Evaluation and Improvement of NDE reliability for Inservice Inspection of Light Water Reactors (NDE Reliability) Program at the Pacific Northwest Laboratory was established by the Nuclear Regulatory Commission to determine the reliability of current inservice inspection (ISI) techniques and to develop recommendations that will ensure a suitably high inspection reliability. The objectives of this program include determining the reliability of ISI performed on the primary systems of commercial light-water reactors (LWRs); using probabilistic fracture mechanics analysis to determine the impact of NDE unreliability on system safety; and evaluating reliability improvements that can be achieved with improved and advanced technology. A final objective is to formulate recommended revisions to the Regulatory and ASME Code requirements, based on material properties, service conditions, and NDE uncertainties

Iowa State University's undergraduate minor, online graduate certificate and resource center in NDE

Science.gov (United States)

Bowler, Nicola; Larson, Brian F.; Gray, Joseph N.

2014-02-01

Nondestructive evaluation is a `niche' subject that is not yet offered as an undergraduate or graduate major in the United States. The undergraduate minor in NDE offered within the College of Engineering at Iowa State University (ISU) provides a unique opportunity for undergraduate aspiring engineers to obtain a qualification in the multi-disciplinary subject of NDE. The minor requires 16 credits of course work within which a core course and laboratory in NDE are compulsory. The industrial sponsors of Iowa State's Center for Nondestructive Evaluation, and others, strongly support the NDE minor and actively recruit students from this pool. Since 2007 the program has graduated 10 students per year and enrollment is rising. In 2011, ISU's College of Engineering established an online graduate certificate in NDE, accessible not only to campus-based students but also to practicing engineers via the web. The certificate teaches the fundamentals of three major NDE techniques; eddy-current, ultrasonic and X-ray methods. This paper describes the structure of these programs and plans for development of an online, coursework-only, Master of Engineering in NDE and thesis-based Master of Science degrees in NDE.

AMES, NESC and ENIQ: European networks in the field of structural integrity involving NDE and inspection effectiveness assessment

International Nuclear Information System (INIS)

Crutzen, S.; Hurst, R.; Debarberis, L.; Lemaitre, P.; Eriksen, B.

1999-01-01

Three European networks on structural integrity aspects of ageing nuclear components are presently managed by the Institute for Advanced Materials of the Joint Research Centre of the European Commission: AMES (Ageing Materials Evaluation and Studies), ENIQ (European Network for Inspection Qualification) and NESC (Network for Evaluating Steel Components). All three networks involve actions, which aim at the effectiveness and reliability assessment of NDE techniques and of inspection procedures: Either for materials damage detection and characterisation or for defect detection and evaluation. This paper is describing very generally the objectives of the three networks and is then concentrating on the results obtained in ENIQ, which are relevant with ISI and regulatory issues. (orig./DGE)

Nonlinear Wave Mixing Technique for Nondestructive Assessment of Infrastructure Materials

Science.gov (United States)

Ju, Taeho

To operate safely, structures and components need to be inspected or monitored either periodically or in real time for potential failure. For this purpose, ultrasonic nondestructive evaluation (NDE) techniques have been used extensively. Most of these ultrasonic NDE techniques utilize only the linear behavior of the ultrasound. These linear techniques are effective in detecting discontinuities in materials such as cracks, voids, interfaces, inclusions, etc. However, in many engineering materials, it is the accumulation of microdamage that leads to degradation and eventual failure of a component. Unfortunately, it is difficult for linear ultrasonic NDE techniques to characterize or quantify such damage. On the other hand, the acoustic nonlinearity parameter (ANLP) of a material is often positively correlated with such damage in a material. Thus, nonlinear ultrasonic NDE methods have been used in recently years to characterize cumulative damage such as fatigue in metallic materials, aging in polymeric materials, and degradation of cement-based materials due to chemical reactions. In this thesis, we focus on developing a suit of novel nonlinear ultrasonic NDE techniques based on the interactions of nonlinear ultrasonic waves, namely wave mixing. First, a noncollinear wave mixing technique is developed to detect localized damage in a homogeneous material by using a pair of noncollinear a longitudinal wave (L-wave) and a shear wave (S-wave). This pair of incident waves make it possible to conduct NDE from a single side of the component, a condition that is often encountered in practical applications. The proposed noncollinear wave mixing technique is verified experimentally by carrying out measurements on aluminum alloy (AA 6061) samples. Numerical simulations using the Finite Element Method (FEM) are also conducted to further demonstrate the potential of the proposed technique to detect localized damage in structural components. Second, the aforementioned nonlinear

A Destructive Validation of NDE Responses of Service-Induced PWSCC Found in North Anna 2 Control Rod Drive Nozzle 31

International Nuclear Information System (INIS)

Cumblidge, Stephen E.; Doctor, Steven R.; Schuster, George J.; Harris, Robert V.; Crawford, Susan L.; Seffens, Rob J.; Toloczko, Mychailo B.; Bruemmer, Stephen M.; Moyer, C.

2009-01-01

Studies conducted at the Pacific Northwest National Laboratory (PNNL) in Richland, Washington focused on assessing the effectiveness of nondestructive examination (NDE) techniques for inspecting control rod drive mechanism (CRDM) nozzles and J-groove weldments. The primary objective of this work is to provide information to the United States Nuclear Regulatory Commission (NRC) on the effectiveness of NDE methods as related to the in-service inspection of CRDM nozzles and J-groove weldments, and to enhance the knowledge base of primary water stress corrosion cracking (PWSCC) through destructive characterization of the CRDM assemblies.

Volume imaging NDE and serial sectioning of carbon fiber composites

Science.gov (United States)

Hakim, Issa; Schumacher, David; Sundar, Veeraraghavan; Donaldson, Steven; Creuz, Aline; Schneider, Rainer; Keller, Juergen; Browning, Charles; May, Daniel; Ras, Mohamad Abo; Meyendorf, Norbert

2018-04-01

A composite material is a combination of two or more materials with very different mechanical, thermal and electrical properties. The various forms of composite materials, due to their high material properties, are widely used as structural materials in the aviation, space, marine, automobile, and sports industries. However, some defects like voids, delamination, or inhomogeneous fiber distribution that form during the fabricating processes of composites can seriously affect the mechanical properties of the composite material. In this study, several imaging NDE techniques such as: thermography, high frequency eddy current, ultrasonic, x-ray radiography, x-ray laminography, and high resolution x-ray CT were conducted to characterize the microstructure of carbon fiber composites. Then, a 3D analysis was implemented by the destructive technique of serial sectioning for the same sample tested by the NDE methods. To better analyze the results of this work and extract a clear volume image for all features and defects contained in the composite material, an intensive comparison was conducted among hundreds of 3D-NDE and multi serial sections' scan images showing the microstructure variation.

Eddy current NDE performance demonstrations using simulation tools

International Nuclear Information System (INIS)

Maurice, L.; Costan, V.; Guillot, E.; Thomas, P.

2013-01-01

To carry out performance demonstrations of the Eddy-Current NDE processes applied on French nuclear power plants, EDF studies the possibility of using simulation tools as an alternative to measurements on steam generator tube mocks-up. This paper focuses on the strategy led by EDF to assess and use code C armel3D and Civa, on the case of Eddy-Current NDE on wears problem which may appear in the U-shape region of steam generator tubes due to the rubbing of anti-vibration bars.

Nondestructive examination (NDE) reliability for inservice inspection of light water reactors

International Nuclear Information System (INIS)

Doctor, S.R.; Deffenbaugh, J.D.; Good, M.S.; Green, E.R.; Heasler, P.G.; Simonen, F.A.; Spanner, J.C.; Taylor, T.T.

1989-10-01

The Evaluation and Improvement of NDE Reliability for Inservice Inspection of Light Water Reactors (NDE Reliability) Program at the Pacific Northwest Laboratory was established by the Nuclear Regulatory Commission to determine the reliability of current inservice inspection (ISI) techniques and to develop recommendations that will ensure a suitably high inspection reliability. The objectives of this program include determining the reliability of ISI performed on the primary systems of commercial light-water reactors (LWRs); using probabilistic fracture mechanics analysis to determine the impact of NDE unreliability on system safety; and evaluating reliability improvement that can be achieved with improved and advanced technology. A final objective is to formulate recommended revisions to ASME Code and Regulatory requirements based on material properties, service conditions, and NDE capabilities and uncertainties. The program scope is limited to ISI of the primary systems including the piping, vessel, and other inspected components. This is a progress report covering the programmatic work from October 1987 through March 1988. 21 refs., 28 figs., 2 tabs

Nondestructive examination (NDE) reliability for inservice inspection of light waters reactors

International Nuclear Information System (INIS)

Doctor, S.R.; Deffenbaugh, J.D.; Good, M.S.; Green, E.R.; Heasler, P.G.; Simonen, F.A.; Spanner, J.C.; Taylor, T.T.

1989-11-01

Evaluation and Improvement of NDE Reliability for Inservice Inspection of Light Water Reactors (NDE Reliability) Program at the Pacific Northwest Laboratory was established by the Nuclear Regulatory Commission to determine the reliability of current inservice inspection (ISI) techniques and to develop recommendations that will ensure a suitably high inspection reliability. The objectives of this program include determining the reliability of ISI performed on the primary systems of commercial light-water reactors (LWRs); using probabilistic fracture mechanics analysis to determine the impact of NDE unreliability on system safety; and evaluating reliability improvements that can be achieved with improved and advanced technology. A final objective is to formulate recommended revisions to ASME Code and Regulatory requirements, based on material properties, service conditions, and NDE uncertainties. The program scope is limited to ISI of the primary systems including the piping, vessel, and other inspected components. This is a progress report covering the programmatic work from April 1988 through September 1988. 33 refs., 70 figs., 12 tabs

Nondestructive Examination (NDE) Reliability for Inservice Inspection of Light Water Reactors

International Nuclear Information System (INIS)

Doctor, S.R.; Diaz, A.A.; Friley, J.R.

1993-09-01

The Evaluation and Improvement of NDE Reliability for Inservice Inspection of Light Water Reactors (NDE Reliability) Program at the Pacific Northwest Laboratory was established by the Nuclear Regulatory Commission to determine the reliability of current inservice inspection (ISI) techniques and to develop recommendations that will ensure a suitably high inspection reliability. The objectives of this program include determining the reliability of ISI performed on the primary systems of commercial light-water reactors (LWRs); using probabilistic fracture mechanics analysis to determine the impact of NDE unreliability on system safety; and evaluating reliability improvements that can be achieved with improved and advanced technology. A final objective is to formulate recommended revisions to ASME Code and Regulatory requirements, based on material properties, service conditions, and NDE uncertainties. The program scope is limited to ISI of the primary systems including the piping, vessel, and other components inspected in accordance with Section XI of the ASME Code. This is a progress report covering the programmatic work from October 1991 through March 1992

Transportation of hydrogen in pipelines: interaction of NDE and material requirements

International Nuclear Information System (INIS)

Thompson, R.B.; Thompson, A.W.; Thompson, D.O.

1976-01-01

The role of nondestructive evaluation (NDE) of materials used in H pipelines and storage facilities is examined. NDE techniques are available which detect critical flaws in today's natural gas lines, and which should have some success in hydrogen lines made of resistant materials. However, the critical flaws in a hydrogen line which is built of a steel whose toughness is significantly reduced in hydrogen, or which contains low-toughness defects such as weld hard spots, would be extremely difficult to detect with today's instrumentation. That instrumentation is designed to test efficiently long lengths of line with minimum disruption of service. Technology is available that would be capable of the more detailed inspection required for the smaller defects. However, the equipment might be expensive and time-consuming to operate, and these costs must be included in the overall assessment of a system using existing lines without embrittlement protection. In addition, it is evident that strong motivation exists to construct new facilities from steels with improved resistance to hydrogen

Technical Letter Report - Preliminary Assessment of NDE Methods on Inspection of HDPE Butt Fusion Piping Joints for Lack of Fusion

International Nuclear Information System (INIS)

Crawford, Susan L.; Cumblidge, Stephen E.; Doctor, Steven R.; Hall, Thomas E.; Anderson, Michael T.

2008-01-01

The U.S. Nuclear Regulatory Commission (NRC) has a multi-year program at the Pacific Northwest National Laboratory (PNNL) to provide engineering studies and assessments of issues related to the use of nondestructive evaluation (NDE) methods for the reliable inspection of nuclear power plant components. As part of this program, there is a subtask 2D that was set up to address an assessment of issues related to the NDE of high density polyethylene (HDPE) butt fusion joints. This work is being driven by the nuclear industry wanting to employ HDPE materials in nuclear power plant systems. This being a new material for use in nuclear applications, there are a number of issues related to its use and potential problems that may evolve. The industry is pursuing ASME Code Case N-755 entitled 'Use of Polyethylene (PE) Plastic Pipe for Section III, Division 1, Construction and Section XI Repair/Replacement Activities' that contains the requirements for nuclear power plant applications of HDPE. This Code Case requires that inspections be performed after the fusion joint is made by visually examining the bead that is formed and conducting a pressure test of the joint. These tests are only effective in general if gross through-wall flaws exist in the fusion joint. The NRC wants to know whether a volumetric inspection can be conducted on the fusion joint that will reliably detect lack-of-fusion conditions that may be produced during joint fusing. The NRC has requested that the work that PNNL is conducting be provided to assist them in resolving this inspection issue of whether effective volumetric NDE can be conducted to detect lack of fusion (LOF) in the butt HDPE joints. PNNL had 24 HDPE pipe specimens manufactured of 3408 material to contain LOF conditions that could be used to assess the effectiveness of NDE in detecting the LOF. Basic ultrasonic material properties were measured and used to guide the use of phased arrays and time-of-flight diffraction (TOFD) work that was

Reliably detectable flaw size for NDE methods that use calibration

Science.gov (United States)

Koshti, Ajay M.

2017-04-01

Probability of detection (POD) analysis is used in assessing reliably detectable flaw size in nondestructive evaluation (NDE). MIL-HDBK-1823 and associated mh18232 POD software gives most common methods of POD analysis. In this paper, POD analysis is applied to an NDE method, such as eddy current testing, where calibration is used. NDE calibration standards have known size artificial flaws such as electro-discharge machined (EDM) notches and flat bottom hole (FBH) reflectors which are used to set instrument sensitivity for detection of real flaws. Real flaws such as cracks and crack-like flaws are desired to be detected using these NDE methods. A reliably detectable crack size is required for safe life analysis of fracture critical parts. Therefore, it is important to correlate signal responses from real flaws with signal responses form artificial flaws used in calibration process to determine reliably detectable flaw size.

NDE for Ablative Thermal Protection Systems, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — This program addresses the need for non-destructive evaluation (NDE) methods for quality assessment and defect evaluation of thermal protection systems (TPS),...

Assessment of NDE Methods on Inspection of HDPE Butt Fusion Piping Joints for Lack of Fusion with Validation from Mechanical Testing

International Nuclear Information System (INIS)

Anderson, Michael T.; Cinson, Anthony D.; Crawford, Susan L.; Doctor, Steven R.; Moran, Traci L.; Watts, Michael W.

2010-01-01

Studies at the Pacific Northwest National Laboratory (PNNL) in Richland, Washington, are being conducted to evaluate nondestructive examinations (NDE) coupled with mechanical testing of butt fusion joints in high-density polyethylene (HDPE) pipe for assessing lack of fusion. The work provides information to the U.S. Nuclear Regulatory Commission (NRC) on the effectiveness of volumetric inspection techniques of HDPE butt fusion joints in Section III, Division 1, Class 3, buried piping systems in nuclear power plants. This paper describes results from preliminary assessments using ultrasonic and microwave nondestructive techniques and mechanical testing with the high-speed tensile impact test and the side-bend test for determining joint integrity. A series of butt joints were fabricated in 3408, 12-in. IPS DR-11 HDPE material by varying the fusion parameters to create good joints and joints containing a range of lack-of-fusion conditions. Six of these butt joints were volumetrically examined with time-of-flight diffraction (TOFD), phased-array (PA) ultrasound, and the Evisive microwave system. The outer-diameter weld beads were removed for the microwave inspection. In two of the four pipes, both the outer and inner weld beads were removed and the pipe joints re-evaluated. The pipes were sectioned and the joints destructively evaluated with the side-bend test by cutting portions of the fusion joint into slices that were planed and bent. The last step in this limited study will be to correlate the fusion parameters, nondestructive, and destructive evaluation results to validate the effectiveness of what each NDE technology detects and what each does not detect. The results of the correlation will be used in identifying any future work that is needed.

NDE for Ablative Thermal Protection Systems, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — This program addresses the need for non-destructive evaluation (NDE) methods for quality assessment and defect evaluation of thermal protection systems (TPS). Novel...

NDE reliability and SAFT-UT final development

International Nuclear Information System (INIS)

Doctor, S.R.; Deffenbaugh, J.D.; Good, M.S.; Green, E.R.; Heasler, P.G.; Reid, L.D.; Simonen, F.A.; Spanner, J.C.; Taylor, T.T.; Vo, T.V.

1990-01-01

The Evaluation and Improvement of NDE Reliability for Inservice Inspection of Light Water Reactors (NDE Reliability) program at the Pacific Northwest Laboratory (PNL) was established by the US Nuclear Regulatory Commission (NRC) to determine the reliability of current inservice inspection (ISI) techniques and to develop recommendations that will ensure a suitably high inspection reliability. This is a progress report covering the programmatic work from October 1987 through September 1988. The program for Validation and Technology Transfer for SAFT-UT is designed to accomplish the final step of moving research results into beneficial application. Accomplishments for FY88 in Synthetic Aperture Focusing of Ultrasonic Test data (SAFT-UT) under this program are discussed in this paper. The information is treated under the copies of Code Activities, Field Validation, and Seminars. (orig.)

Nondestructive Examination (NDE) Reliability for Inservice Inspection of Light Water Reactors

International Nuclear Information System (INIS)

Doctor, S.R.; Diaz, A.A.; Friley, J.R.; Good, M.S.; Greenwood, M.S.; Heasler, P.G.; Hockey, R.L.; Kurtz, R.J.; Simonen, F.A.; Spanner, J.C.; Taylor, T.T.; Vo, T.V.

1992-07-01

The Evaluation and Improvement of NDE Reliability for Inservice Inspection of Light Water Reactors (NDE Reliability) Program at the Pacific Northwest Laboratory was established by the Nuclear Regulatory Commission to determine the reliability of current inservice inspection (ISI) techniques and to develop recommendations that will ensure a suitably high inspection reliability. The objectives of this program include determining the reliability of ISI performed on the primary systems of commercial light-water reactors (LWR's); using probabilistic fracture mechanics analysis to determine the impact of NDE unreliability on system safety; and evaluating reliability improvements that can be achieved with improved and advanced technology. A final objective is to formulate recommended revisions to the Regulatory and ASME Code requirements, based on material properties, service conditions, and NDE uncertainties. The program scope is limited to ISI of the primary systems including the piping, vessel, and other components inspected in accordance with Section XI of the ASME Code. This is a progress report covering the programmatic work from April 1991 through September 1991

Nondestructive Examination (NDE) Reliability for Inservice Inspection of Light Water Reactors

International Nuclear Information System (INIS)

Doctor, S.R.; Diaz, A.A.; Friley, J.R.; Greenwood, M.S.; Heasler, P.G.; Kurtz, R.J.; Simonen, F.A.; Spanner, J.C.; Vo, T.V.

1993-11-01

The Evaluation and Improvement of NDE Reliability for Inservice inspection of Light Water Reactors (NDE Reliability) Program at the Pacific Northwest Laboratory was established by the Nuclear Regulatory Commission to determine the reliability of current inservice inspection (ISI) techniques and to develop recommendations that will ensure a suitably high inspection reliability. The objectives of this program include determining the reliability of ISI performed on the primary systems of commercial light-water reactors (LWRs);using probabilistic fracture mechanics analysis to determine the impact of NDE unreliability on system safety; and evaluating reliability improvements that can be achieved with improved and advanced technology. A final objective is to formulate recommended revisions to the Regulatory and ASME Code requirements, based on material properties, service conditions, and NDE uncertainties. The program scope is limited to ISI of the primary systems including the piping, vessel and other components inspected in accordance with Section XI of the ASME Code. This is a programs report covering the programmatic work from April 1992 through September 1992

Nondestructive examination (NDE) reliability for inservice inspection of light water reactors

International Nuclear Information System (INIS)

Doctor, S.R.; Good, M.S.; Green, E.R.; Heasler, P.G.; Simonen, F.A.; Spanner, J.C.; Taylor, T.T.; Vo, T.V.

1991-08-01

The Evaluation and Improvement of NDE Reliability for Inservice Inspection of Light Water Reactors (NDE Reliability) Program at the Pacific Northwest Laboratory was established by the Nuclear Regulatory Commission to determine the reliability of current inservice inspection (ISI) techniques and to develop recommendations that will ensure a suitably high inspection reliability. The objectives of this program include determining the reliability of ISI performed on the primary systems of commercial light-water reactors (LWRs); using probabilistic fracture mechanics analysis to determine the impact of NDE unreliability on system safety; and evaluating reliability improvements that can be achieved with improved and advanced technology. A final objective is to formulate recommended revisions to ASME Code and Regulatory requirements, based on material properties, service conditions, and NDE uncertainties. The program scope is limited to ISI of the primary systems including the piping, vessel, and other components inspected in accordance with Section 6 of the ASME Code. This is a progress report covering the pro grammatic work from April 1989 through September 1989. 12 refs., 4 figs. 5 tabs

The role of small business in innovative NDE

International Nuclear Information System (INIS)

Berger, H.

1983-01-01

Small business is a strong element in the economy in terms of employment, new jobs and the introduction of new products and services. In NDE, small companies have introduced new ideas, products and techniques, making these available for improved inspection. Given more opportunity, small business can be an even stronger factor in NDE technology transfer. This opportunity might be provided in the form of: Greater assistance and encouragement from large organizations who do not plan to move forward on developments within their own laboratories; Greater recognition for people who display the innovative, entrepreneurial spirit needed to start new ventures; and More opportunities in R and D - either in direct contract support or in a subcontractor role in which the small business innovative spirit is encouraged

NDE and plant life extension

International Nuclear Information System (INIS)

Liu, S.N.; Ammirato, F.V.; Nottingham, L.D.

1991-01-01

Component life extension is the process of making run-repair-replace decisions for plant components and includes a thorough analysis of the capability of the component to perform throughout the projected lifetime. For many critical plant components, nondestructive evaluation (NDE) is essential in determining whether the component can be operated safely and economically in the extended life period and to help utilities determine safe and economic inspection intervals. NDE technology is required for not only detecting defects that could grow to a size of concern during extended lifetimes, but also will be called upon to measure and monitor accumulating material degradation that strongly affects component reliability. This paper discusses the role of NDE in life extension by reviewing three examples--a reactor pressure vessel, steam turbine-generator rotors, and generator retaining rings. In each example, the contribution of NDE to life extension decisions is described. (author)

NDE training activities at the EPRI NDE center

International Nuclear Information System (INIS)

Anon.

1987-01-01

The need for an industry-wide qualification for NDE personnel is becoming more evident in both in-service inspection and technical skills training. ASME Section XI requirements for the qualification and certification of visual, ultrasonic, and eddy current examines is one of the major areas being supported by training at the Center. The other major thrust is in response to the Boiling Water Reactor Owners Group and its recognition of the importance of the UT operator's accurately detecting, discriminating, and sizing intergranular stress corrosion cracks (IGSCC) in piping, and inspecting weld overlay repairs of these cracked pipes. In addition, the pressurized water reactor (PWR) utilities have recognized the importance of improved eddy current data analysis of steam generator tubing. The overall intent of the Center's training is to meet the most critical utility needs with quality training that can be used by the trainee's employer as a part of its certification of that individual. To do this, the Center has organized and activated a carefully maintained documentation and records system built around the Continuing Education Unit (CEU). To address the problem of the small supply of entry-level NDE personnel available to the utilities, the Center has developed, through its Human Resource Development, academic and utility co-op programs to generate guidelines and NDE teaching materials for high schools, technical schools, and universities

Robot-arm-based mobile HTS SQUID system for NDE of structures

Energy Technology Data Exchange (ETDEWEB)

Yotsugi, K; Hatsukade, Y; Tanaka, S [Department of Ecological Engineering, Toyohashi University of Technology, 1-1 Hibarigaoka, Tenpaku-cho, Toyohashi, Aichi 441-8580 (Japan)], E-mail: hatukade@eco.tut.ac.jp

2008-02-01

A robot-arm-based mobile HTS SQUID system was developed for NDE of fixed targets. To realize the system, active magnetic shielding technique using fluxgate as reference sensor for ambient field was applied to a cryocooler-based HTS SQUID gradiometer that was mounted on commercial robot-arm. In this technique, ambient field noise and pulse noise of 550 nT from robot were measured by the fluxgate near the SQUID, and then the fluxgate output was negatively fed back to generate compensation field around the SQUID and fluxgate. The noise from robot was reduced by a factor of about 20 and the shielding technique enabled the HTS SQUID to move in unshielded environment by the robot-arm without flux-trapping or unlocking at 10 mm/s. System noise measurement and inspection of hidden cracks in multi-layer composite-metal structure were demonstrated using the mobile SQUID-NDE system.

Evaluation of computer-based NDE techniques and regional support of inspection activities

International Nuclear Information System (INIS)

Taylor, T.T.; Kurtz, R.J.; Heasler, P.G.; Doctor, S.R.

1991-01-01

This paper describes the technical progress during fiscal year 1990 for the program entitled 'Evaluation of Computer-Based nondestructive evaluation (NDE) Techniques and Regional Support of Inspection Activities.' Highlights of the technical progress include: development of a seminar to provide basic knowledge required to review and evaluate computer-based systems; review of a typical computer-based field procedure to determine compliance with applicable codes, ambiguities in procedure guidance, and overall effectiveness and utility; design and fabrication of a series of three test blocks for NRC staff use for training or audit of UT systems; technical assistance in reviewing (1) San Onofre ten year reactor pressure vessel inservice inspection activities and (2) the capability of a proposed phased array inspection of the feedwater nozzle at Oyster Creek; completion of design calculations to determine the feasibility and significance of various sizes of mockup assemblies that could be used to evaluate the effectiveness of eddy current examinations performed on steam generators; and discussion of initial mockup design features and methods for fabricating flaws in steam generator tubes

NDE Big Data Framework, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — NDE data has become "Big Data", and is overwhelming the abilities of NDE technicians and commercially available tools to deal with it. In the current state of the...

NDE of ceramic insulator blanks by radiography

International Nuclear Information System (INIS)

Sarvanan, S.; Venkatraman, B.; Jayakumar, T.; Baldev Raj

1996-01-01

The production of ceramic insulators in electrical industry involves a number of steps, one of which is the green blank. The defects such as voids and crack can be present in the extruded green blank. One of the best non-destructive evaluation (NDE) technique radiography. This paper deals with the development of methodology based on theoretical modeling for the examination of ceramics by high sensitivity radiography. (author)

An Integrated NDE and FEM Characterization of Composite Rotors

Science.gov (United States)

Abdul-Aziz, Ali; Baaklini, George Y.; Trudell, Jeffrey J.

2000-01-01

A structural assessment by integrating finite-element methods (FEM) and a nondestructive evaluation (NDE) of two flywheel rotor assemblies is presented. Composite rotor A is pancake like with a solid hub design, and composite rotor B is cylindrical with a hollow hub design. Detailed analyses under combined centrifugal and interference-fit loading are performed. Two- and three-dimensional stress analyses and two-dimensional fracture mechanics analyses are conducted. A comparison of the structural analysis results obtained with those extracted via NDE findings is reported. Contact effects due to press-fit conditions are evaluated. Stress results generated from the finite-element analyses were corroborated with the analytical solution. Cracks due to rotational loading up to 49 000 rpm for rotor A and 34 000 rpm for rotor B were successfully imaged with NDE and predicted with FEM and fracture mechanics analyses. A procedure that extends current structural analysis to a life prediction tool is also defined.

Benchmarking of Computational Models for NDE and SHM of Composites

Science.gov (United States)

Wheeler, Kevin; Leckey, Cara; Hafiychuk, Vasyl; Juarez, Peter; Timucin, Dogan; Schuet, Stefan; Hafiychuk, Halyna

2016-01-01

Ultrasonic wave phenomena constitute the leading physical mechanism for nondestructive evaluation (NDE) and structural health monitoring (SHM) of solid composite materials such as carbon-fiber-reinforced polymer (CFRP) laminates. Computational models of ultrasonic guided-wave excitation, propagation, scattering, and detection in quasi-isotropic laminates can be extremely valuable in designing practically realizable NDE and SHM hardware and software with desired accuracy, reliability, efficiency, and coverage. This paper presents comparisons of guided-wave simulations for CFRP composites implemented using three different simulation codes: two commercial finite-element analysis packages, COMSOL and ABAQUS, and a custom code implementing the Elastodynamic Finite Integration Technique (EFIT). Comparisons are also made to experimental laser Doppler vibrometry data and theoretical dispersion curves.

Neutron radiography and other NDE tests of main rotor helicopter blades

CSIR Research Space (South Africa)

De Beer, FC

2004-10-01

Full Text Available leading to aircraft structural failures, are addressed by various NDE techniques. In a combined investigation by means of visual inspection, X-ray radiography and shearography on helicopter main rotor blades, neutron radiography (NRad) at SAFARI-1 research...

Training activities at the EPRI NDE Center

International Nuclear Information System (INIS)

Pherigo, G.

1986-01-01

The Electric Power Research Institute (EPRI), through its Nondestructive Examination (NDE) Center in Charlotte, North Carolina, has identified two specific categories of NDE training to best serve the industry's need for enhanced personnel qualification programs. These categories include in-service inspection (ISI) training and technical skills training. The ISI training provides operator training in new NDE technology areas that are ready for field application. The technical skills training is developed as part of a long-range plan to support all basic NDE methods typical to the electric power industry. The need for specific training and better documentation of NDE personnel qualifications is becoming more evident. ASME Section XI requirements for the qualification and certification of visual examiners and the recognition by the US Nuclear Regulatory Commission (NRC) of the importance of the ultrasonic (UT) operator in finding intergranular stress corrosion cracking (IGSCC) are two of the major issues being addressed by the training task of the EPRI NDE Center. The overall intent of the center's training is to meet the most critical utility needs with quality training that can be used by the trainee's employer as a part of their certification of that individual. To do this, the center has organized and activated a carefully maintained documentation and records systems built around the continuing education unit

Evaluation and improvement in nondestructive examination (NDE) reliability for inservice inspection of light water reactors

International Nuclear Information System (INIS)

Doctor, S.R.; Deffenbaugh, J.D.; Good, M.S.; Green, E.R.; Heasler, P.G.; Simonen, F.A.; Spanner, J.C.; Taylor, T.T.

1988-01-01

The Evaluation and Improvement of NDE Reliability for Inservice Inspection of Light Water Reactors (NDE Reliability) program at the Pacific Northwest Laboratory was established by the NRC to determine the reliability of current inservice inspection (ISI) techniques and to develop recommendations that will ensure a suitably high inspection reliability. The objectives of this program include determining the reliability of ISI performed on the primary systems of commercial light-water reactors (LWRs); using probabilistic fracture mechanics analysis to determine the impact of NDE unreliability on system safety; and evaluating reliability improvements that can be achieved with improved and advanced technology. A final objective is to formulate recommended revisions to ASME Code and Regulatory requirements, based on material properties, service conditions and NDE uncertainties. The program scope is limited to ISI of the primary systems including the piping, vessel, and other inspected components. This is a progress report covering the programmatic work from October 1986 through September 1987. (author)

Evaluation and improvement in nondestructive examination (NDE) reliability for inservice inspection of light water reactors

International Nuclear Information System (INIS)

Doctor, S.R.; Deffenbaugh, J.D.; Good, M.S.; Green, E.R.; Heasler, P.G.; Simonen, F.A.; Spanner, J.C.; Taylor, T.T.

1988-01-01

The Evaluation and Improvement of NDE Reliability for Inservice Inspection of Light Water Reactor (NDE Reliability) program at the Pacific Northwest Laboratory was established by the NRC to determine the reliability of current inservice inspection (ISI) techniques and to develop recommendations that will ensure a suitably high inspection reliability. The objectives of this program include determining the reliability of ISI performed on the primary systems of commercial light-water reactors (LWRs); using probabilistic fracture mechanics analysis to determine the impact of NDE unreliability on system safety; and evaluating reliability improvements that can be achieved with improved and advanced technology. A final objective is to formulate recommended revisions to ASME Code and Regulatory requirements, based on material properties, service conditions, and NDE uncertainties. The program scope is limited to ISI of the primary systems including the piping, vessel, and other inspected components. This is a progress report covering the programmatic work from October 1986 through September 1987

NDE fo Sizewell B

International Nuclear Information System (INIS)

Baborovsky, V.M.; Whittle, M.J.

1988-01-01

A key feature of the safety case for Sizewell B is the extensive NDE proposed for all primary circuit components whose failure must be demonstrated to be incredible. These incredibility of failure components include the reactor pressure vessel, the pressurizer, steam generator shells and reactor coolant pump casings. All of them are to be inspected by repeated, independent inspections using diverse techniques to ensure the highest reliability. The inspections themselves are checked by an independent inspection validation center. This paper reviews the progress made in implementing the above proposals. A number of components have already been inspected, other inspections are imminent. The work has required major technical and administrative innovations and these are described

Through the looking glass: The future for NDE?

Science.gov (United States)

Bond, Leonard J.

2014-02-01

Nondestructive testing (NDT) is a mature industry, with global equipment sales fast moving towards 2B. per year. The use of conventional NDT will grow in developing countries and in developed countries the challenges will include those associated with maintaining aging infrastructure. For some systems the future will move to structural health monitoring (SHM) and for others into integration of online measurements in manufacturing. Nondestructive Evaluation (NDE) is a multi-disciplinary area of endeavor that has its origins in materials science and NDT. It seeks to provide an adequate science base for NDT to become a quantitative science. It was seen to be necessary to better detect, size and type defects, improve the reliability of inspection, and probability of detection (POD). There is particular interest in estimating the potential defects could have on performance or potential for loss of structural integrity, under various loading or stressor conditions, and ultimately implement risk-based reliability assessments. NDE must be seen more as a part of the wide field of engineering, as an interdisciplinary endeavor, that brings together the expertise of materials science and metrology, together with the underlying physics for inspection methods, as well as statistics, computers, robotics and software. The adoption of advanced manufacturing, will require new metrology tools and methods to provide data for assessing new materials including powder metals, as used in additive manufacturing, and various composites. The lessons from the past proceedings of this conference series include that the problems faced today are harder than was expected during the first decade of quantitative NDE research. Even with new types of transducers and much improved A/D and powerful computers new approaches and more basic measurement physics being understood, new insights are needed to provide the data needed to solve many real-world NDE problems, to understand and measure early

Quantitative ultrasonic coda wave (diffuse field) NDE of carbon-fiber reinforced polymer plates

Science.gov (United States)

Livings, Richard A.

The increasing presence and applications of composite materials in aerospace structures precipitates the need for improved Nondestructive Evaluation (NDE) techniques to move from simple damage detection to damage diagnosis and structural prognosis. Structural Health Monitoring (SHM) with advanced ultrasonic (UT) inspection methods can potentially address these issues. Ultrasonic coda wave NDE is one of the advanced methods currently under investigation. Coda wave NDE has been applied to concrete and metallic specimens to assess damage with some success, but currently the method is not fully mature or ready to be applied for SHM. Additionally, the damage diagnosis capabilities and limitations of coda wave NDE applied to fibrous composite materials have not been widely addressed in literature. The central objective of this work, therefore, is to develop a quantitative foundation for the use of coda wave NDE for the inspection and evaluation of fibrous composite materials. Coda waves are defined as the superposition of late arriving wave modes that have been scattered or reflected multiple times. This results in long, complex signals where individual wave modes cannot be discriminated. One method of interpreting the changes in such signals caused by the introduction or growth of damage is to isolate and quantify the difference between baseline and damage signals. Several differential signal features are used in this work to quantify changes in the coda waves which can then be correlated to damage size and growth. Experimental results show that coda wave differential features are effective in detecting drilled through-holes as small as 0.4 mm in a 50x100x6 mm plate and discriminating between increasing hole diameter and increasing number of holes. The differential features are also shown to have an underlying basis function that is dependent on the hole volume and can be scaled by a material dependent coefficient to estimate the feature amplitude and size holes. The

An Assessment of NDE Capability and Materials Characterization for Complex Additive Manufacturing Aerospace Components

Data.gov (United States)

National Aeronautics and Space Administration — This multi-center activity investigates the correlation between nondestructive evaluation (NDE), mechanical testing, microstructure, and additive manufacturing (AM)...

Fault-Tolerant NDE Data Reduction Framework, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — A distributed fault tolerant nondestructive evaluation (NDE) data reduction framework is proposed in which large NDE datasets are mapped to thousands to millions of...

NDE measurements for understanding of performance: A few case studies on engineering components, human health and cultural heritage

Science.gov (United States)

Raj, Baldev; Venkatraman, B.

2013-01-01

Life cycle management involves a seamless integration of materials, design, analysis, production, manufacturing, and degradation plus, a wide variety of disciplines relating to surveillance and characterisation with adequate feedback and control. Science and technology of non-destructive evaluation (NDE) links all these domains and disciplines together in a seamless and robust manner. A number of research programs on NDE science and technology have evolved during the last four decades world over including the one at Indira Gandhi Centre for Atomic Research, Kalpakkam, initiated and nurtured by the first author. Many engineering and technology challenges pertaining to fast spectrum reactors have been successfully solved by this Centre through development of innovative sensors, procedures and coupled with strong basic science and modeling approaches. These technologies have also been selectively applied in gaining insights of human health and cultural heritage. This paper highlights some of the innovative NDE sensors and techniques developed in the field of electromagnetic NDE and their successful applications. A few interesting case studies pertaining to NDE in heritage and healthcare using acoustic and thermal methods are also presented.

IVA Ultrasonic and Eddy Current NDE for ISS

Data.gov (United States)

National Aeronautics and Space Administration — The project intends to develop a combined Ultrasonic and Eddy Current nondestructive evaluation (NDE) instrument for IVA use on ISS. A suite of IVA and EVA NDE...

Toward automated interpretation of integrated information: Managing "big data" for NDE

Science.gov (United States)

Gregory, Elizabeth; Lesthaeghe, Tyler; Holland, Stephen

2015-03-01

Large scale automation of NDE processes is rapidly maturing, thanks to recent improvements in robotics and the rapid growth of computer power over the last twenty years. It is fairly straightforward to automate NDE data collection itself, but the process of NDE remains largely manual. We will discuss three threads of technological needs that must be addressed before we are able to perform automated NDE. Spatial context, the first thread, means that each NDE measurement taken is accompanied by metadata that locates the measurement with respect to the 3D physical geometry of the specimen. In this way, the geometry of the specimen acts as a database key. Data context, the second thread, means that we record why the data was taken and how it was measured in addition to the NDE data itself. We will present our software tool that helps users interact with data in context, Databrowse. Condition estimation, the third thread, is maintaining the best possible knowledge of the condition (serviceability, degradation, etc.) of an object or part. In the NDE context, we can prospectively use Bayes' Theorem to integrate the data from each new NDE measurement with prior knowledge. These tools, combined with robotic measurements and automated defect analysis, will provide the information needed to make high-level life predictions and focus NDE measurements where they are needed most.

The EPRI NDE center after five years

International Nuclear Information System (INIS)

Dau, G.J.; Nemzek, T.A.

1985-01-01

In 1979, the Electric Power Research Institute (EPRI) established a Nondestructive Evaluation (NDE) Center. The purpose of the Center is to provide the electric utility industry with a dedicated NDE development and field-use-qualification capability. Later, the scope of activities at the NDE Center was expanded. Beginning in 1980, the BWR Owners Group (IGSCC) provided funding necessary to operate the BWR Pipe Remedy Demonstration and Training Facility. In 1984, the Maintenance Equipment Applications Center was established by EPRI. Both functions are co-located within the NDE Center. All three functions share common objectives of providing the electric utility industry with a capability dedicated to assuring reduction to practice of new or improved technology, proof testing, qualification for field use, and obtaining code and regulatory acceptance of qualified methods and training. The purpose of this paper is to describe typical activities of the Center and some of the benefits that have accrued. The next section describes the Center organization, operation, and facility, while the remaining sections discuss the technology transfer thrust and benefits

Assessment of NDE Technologies for Detection and Characterization of Stress Corrosion Cracking in LWRs

Energy Technology Data Exchange (ETDEWEB)

Meyer, Ryan M.; Ramuhalli, Pradeep; Toloczko, Mychailo B.; Bond, Leonard J.; Montgomery, Robert O.

2012-12-31

Stress corrosion cracking (SCC) in light water reactors (LWRs) has been a persistent form of degradation in the nuclear industry. Examples of SCC can be found for a range of materials in boiling and pressurized water reactor environments, including carbon steels, stainless steels, and nickel-base stainless alloys. The evolution of SCC is often characterized by a long initiation stage followed by a phase of more rapid crack growth to failure. This provides a relatively short window of opportunity to detect the start of observable SCC, and it is conceivable that SCC could progress from initiation to failure between subsequent examinations when managed by applying periodic in-service inspection techniques. Implementation of advanced aging management paradigms in the current fleet of LWRs will require adaptation of existing measurement technologies and development of new technologies to perform on-line measurements during reactor operation to ensure timely detection of material degradation and to support the implementation of advanced diagnostics and prognostics. This paper considers several non-destructive examination (NDE) technologies with known sensitivity to detection of indicators for SCC initiation and/or propagation, and assesses these technologies with respect to their ability to detect and accurately characterize the significance of an SCC flaw. Potential strategies to improve SCC inspection or monitoring performance are offered to benefit management of SCC degradation in LWRs.

Assessment of NDE technologies for detection and characterization of stress corrosion cracking in LWRs

International Nuclear Information System (INIS)

Meyer, R.M.; Ramuhalli, P.; Toloczko, M.B.; Bond, L.J.; Montgomery, R.O.

2012-01-01

Stress corrosion cracking (SCC) in light water reactors (LWRs) has been a persistent form of degradation in the nuclear industry. Examples of SCC can be found for a range of materials in boiling and pressurized water reactor environments, including carbon steels, stainless steels, and nickel-base alloys. The evolution of SCC is often characterized by a long initiation stage followed by a phase of more rapid crack growth to failure. This provides a relatively short window of opportunity to detect the start of observable SCC, and it is conceivable that SCC could progress from initiation to failure between subsequent examinations when managed by applying periodic in-service inspection techniques. Implementation of advanced aging management paradigms in the current fleet of LWRs will require adaptation of existing measurement technologies and development of new technologies to perform on-line measurements during reactor operation to ensure timely detection of material degradation and to support the implementation of advanced diagnostics and prognostics. This paper considers several non-destructive examination (NDE) technologies with known sensitivity to detection of indicators for SCC initiation and/or propagation, and assesses these technologies with respect to their ability to detect and accurately characterize the significance of an SCC flaw. Potential strategies to improve SCC inspection or monitoring performance are offered to benefit management of SCC degradation in LWRs. (author)

NDE for Characterizing Oxidation Damage in Reinforced Carbon-Carbon

Science.gov (United States)

Roth, Don J.; Rauser, Richard W.; Jacobson, nathan S.; Wincheski, Russell A.; Walker, James L.; Cosgriff, Laura A.

2009-01-01

In this study, coated reinforced carbon-carbon (RCC) samples of similar structure and composition as that from the NASA space shuttle orbiter s thermal protection system were fabricated with slots in their coating simulating craze cracks. These specimens were used to study oxidation damage detection and characterization using NDE methods. These specimens were heat treated in air at 1143 and 1200 C to create cavities in the carbon substrate underneath the coating as oxygen reacted with the carbon and resulted in its consumption. The cavities varied in diameter from approximately 1 to 3 mm. Single-sided NDE methods were used since they might be practical for on-wing inspection, while x-ray micro-computed tomography (CT) was used to measure cavity sizes in order to validate oxidation models under development for carbon-carbon materials. An RCC sample having a naturally-cracked coating and subsequent oxidation damage was also studied with x-ray micro-CT. This effort is a follow-on study to one that characterized NDE methods for assessing oxidation damage in an RCC sample with drilled holes in the coating. The results of that study are briefly reviewed in this article as well. Additionally, a short discussion on the future role of simulation to aid in these studies is provided.

Pressure tube replication techniques using the advanced NDE system

International Nuclear Information System (INIS)

Isherwood, A.; Jarron, D.; Travers, J.; Hanley, K.

2006-01-01

Periodic and in-service inspections of fuel channels are essential for the proper assessment of the structural integrity of these vital components. The arrival of new delivery devices for fuel channel inspections has driven new tooling for gathering and analyzing NDE data. The Advanced Non-Destructive Examination (ANDE) Replication System has been designed to compliment the ANDE Inspection System by providing a two plate replica system. These plates deliver a compound that makes a positive 3D mould of known ID flaws to gather information for flaw assessment. The two plate system, and the ability to retrieve and recharge the moulds in the reactor vault allows for gathering defect information with minimal critical path time. The ANDE Replication System was built on the foundation of CIGAR experience by a solid design team familiar with 3D CAD and manufacturing techniques. The tooling and controls went through a series of integration stages in the laboratory and then later with the Universal Delivery Machine (UDM) before being used on reactor starting in 2003. Once the inspection phase of an outage has been completed, the analysis team provides a list of flaw candidates that require 'root radius' information to complete the flaw assessment. This is a measure of how sharp the corners are in the defect. This data is used as part of the stress calculation that ultimately determines how many shutdown cycles that the reactor can have before that flaw must be re-inspected. The inspection tool is then swapped out of the delivery machine in the reactor vault using the versatile connectorized umbilical. The replication tool is loaded on the machine, charged with replica compound on each of the two plates, and then sent to the target channel(s). On channel, the operators use the same console as the ANDE Inspection System, but have a separate control system with a graphical display of the tool that shows its position in the channel with respect to the E-face. The axial and

Qualification of NDE personnel in the nuclear industry

International Nuclear Information System (INIS)

Epps, T.N.

1984-01-01

There has been evidence of ineffective programs for certifying nondestructive examination (NDE) personnel who conduct periodic inservice examinations in nuclear power plants under ASME Section XI Code requirements. This was brought to the attention of a group from the electric utility industry, the Electric Power Research Institute (EPRI), some NDE consultants and representatives from the American Society of Mechanical Engineers (ASME) by the Nuclear Regulatory Commission (NRC) in a May, 1982 meeting in Bethesda, Maryland. One problem pointed out by the NRC was the lack of a clear definition of qualification requirements for certification of NDE personnel who conduct ASME Section XI Inservice Inspection work in nuclear power plants. The NRC requested that the nuclear industry resolve this problem by formulating definitive qualification requirements for personnel certification that could be made an industry requirement. In June, 1982 the EPRI NDE Subcommittee held a general meeting for utility representatives to discuss the results of the May, 1982 meeting to develop a plan for industry response to the issue. The consensus was that an Ad Hoc Committee of utility representatives be convened to develop a document outlining qualification requirements for vertification of NDE personnel. The Ad Hoc Committee was formally convened on September 29, 1982

Global NDE Best Practice for Technology Improvement, Outage Management, Foreign Material Exclusion and Dose Control

International Nuclear Information System (INIS)

Glass, S. W.; Mohr, F.

2010-01-01

Non Destructive Examination (NDE) is a critical element of both Boiling Water and Pressurized Water Reactor outages. Frequently this includes critical path activity so both the utility and the inspection vendor are under intense pressure to perform the work quickly. Concurrent with AREVA's new global organization of NDE resources, AREVA NDE SOLUTIONS, efforts have intensified for global application of lessons learned and best practices. These best practices include new developments as well as continuous improvements to well established tools and NDE techniques. Advancements range from steam generator robots, advanced steam generator deposit characterization sensors and method, new phased array approaches for PWR and BWR reactor vessel examination, new sensors and approaches for RPV head examinations, plus advanced internals examination robots and methods. In addition to specialized tools and techniques, best practice includes numerous management innovations. AREVA's multi-disciplined integrated nuclear worker strategy helps to minimize the total number of personnel deployed to multi-task outages. Specific design and on-site practice has been implemented to minimize or eliminate foreign material from the reactor system and vigorous pursuit of dose management practices keeps our nuclear worker dose as low as reasonably achievable. The industry is moving to much more conservative nuclear worker dose limits. While this is proving to be an issue with many vendors, AREVA has had an internal policy of <2R since 2006. Globalizing the organization also helps AREVA manage peaks and unplanned emergency inspections from an enlarged pool of globally qualified inspection personnel and tools. (Author)

Transverse vibration technique to identify deteriorated wood floor systems

Science.gov (United States)

R.J. Ross; X. Wang; M.O. Hunt; L.A. Soltis

2002-01-01

The Forest Products Laboratory, USDA Forest Service, has been developing nondestructive evaluation (NDE) techniques to identify degradation of wood in structures and the performance characteristics that remain in the structure. This work has focused on using dynamic testing techniques, particularly stress wave and ultrasonic transmission NDE techniques for both...

Evaluation and improvement in nondestructive examination (NDE) reliability for inservice inspection of light water reactors

International Nuclear Information System (INIS)

Doctor, S.R.; Andersen, E.S.; Bowey, R.E.; Diaz, A.A.; Good, M.S.; Heasler, P.G.; Hockey, R.L.; Simonen, F.A.; Spanner, J.C.; Taylor, T.T.; Vo, T.V.

1991-01-01

This program is intended to establish the effectiveness, reliability and adequacy of inservice inspection of reactor pressure vessels and primary piping systems and the impact of ISI reliability on system integrity. The objectives of the program include: (a) determine the effectiveness and reliability of ultrasonic inservice inspection (ISI) performed on commercial, light water reactor pressure vessels and piping; (b) recommend Code changes to the inspection procedures to improve the reliability of ISI; (c) using fracture mechanics analysis, determine the impact of NDE unreliability on system safety and determine the level of inspection reliability required to assure a suitably low failure probability; (d) evaluate the degree of reliability improvement which could be achieved using improved NDE techniques; and (e) based on importance of component to safety, material properties, service conditions, and NDE uncertainties, formulate improved inservice inspection criteria (including sampling plan, frequency, and reliability of inspection) for revisions to ASME Section XI and regulatory requirements needed to assure suitably low failure probabilities

Comparison of normal and phase stepping shearographic NDE

Science.gov (United States)

Andhee, A.; Gryzagoridis, J.; Findeis, D.

2005-05-01

The paper presents results of non-destructive testing of composite main rotor helicopter blade calibration specimens using the laser based optical NDE technique known as Shearography. The tests were performed initially using the already well established near real-time non-destructive technique of Shearography, with the specimens perturbed during testing for a few seconds using the hot air from a domestic hair dryer. Subsequent to modification of the shearing device utilized in the shearographic setup, phase stepping of one of the sheared images to be captured by the CCD camera was enabled and identical tests were performed on the composite main rotor helicopter blade specimens. Considerable enhancement of the images manifesting or depicting the defects on the specimens is noted suggesting that phase stepping is a desirable enhancement technique to the traditional Shearographic setup.

NDE Acoustic Microscopy Research Laboratory

Data.gov (United States)

Federal Laboratory Consortium — The purpose is to develop advanced, more effective high-resolution micro-NDE materials characterization methods using scanning acoustic microscopy. The laboratory's...

Status of integration of small computers into NDE systems

International Nuclear Information System (INIS)

Dau, G.J.; Behravesh, M.M.

1988-01-01

Introduction of computers in nondestructive evaluations (NDE) has enabled data acquisition devices to provide a more thorough and complete coverage in the scanning process, and has aided human inspectors in their data analysis and decision making efforts. The price and size/weight of small computers, coupled with recent increases in processing and storage capacity, have made small personal computers (PC's) the most viable platform for NDE equipment. Several NDE systems using minicomputers and newer PC-based systems, capable of automatic data acquisition, and knowledge-based analysis of the test data, have been field tested in the nuclear power plant environment and are currently available through commercial sources. While computers have been in common use for several NDE methods during the last few years, their greatest impact, however, has been on ultrasonic testing. This paper discusses the evolution of small computers and their integration into the ultrasonic testing process

Considerations for ultrasonic testing application for on-orbit NDE

Science.gov (United States)

Koshti, Ajay M.

2015-04-01

The paper addresses some on-orbit nondestructive evaluation (NDE) needs of NASA for International Space Station (ISS). The presentation gives NDE requirements for inspecting suspect damage due to micro-meteoroids and orbital debris (MMOD) impact on the pressure wall of the ISS. This inspection is meant to be conducted from inside of the ISS module. The metallic wall of the module has a fixed wall thickness but also has integral orthogrid ribs for reinforcement. Typically, a single MMOD hit causes localized damage in a small area causing loss of material similar to pitting corrosion, but cracks may be present too. The impact may cause bulging of the wall. Results of the ultrasonic and eddy current demonstration scans on test samples are provided. The ultrasonic technique uses shear wave scans to interrogate the localized damage area from the surrounding undamaged area. The scanning protocol results in multiple scans, each with multiple "vee" paths. A superimposition and mosaic of the three-dimensional ultrasonic data from individual scans is desired to create C-scan images of the damage. This is a new data reduction process which is not currently implemented in state-of-art ultrasonic instruments. Results of ultrasonic scans on the simulated MMOD damage test plates are provided. The individual C-scans are superimposed manually creating mosaic of the inspection. The resulting image is compared with visibly detected damage boundaries, X-ray images, and localized ultrasonic and eddy current scans for locating crack tips to assess effectiveness of the ultrasonic scanning. The paper also discusses developments needed in improving ergonomics of the ultrasonic testing for on-orbit applications.

Trends in NDE science and technology: proceedings of the fourteenth world conference on NDT. V. 1

International Nuclear Information System (INIS)

Krishnadas Nair, C.G.; Baldev Raj; Murthy, C.R.L.; Jayakumar, T.

1996-01-01

The multi volume proceedings of the 14th World Conference on Nondestructive Testing (NDT) cover the applications of Nondestructive Evaluation (NDE) in a wide range of industries, viz. aerospace, chemical, defence, manufacturing, nuclear etc. and for different materials. The major topics covered under it are NDE in nuclear industry, NDE of tubes and bars, non destructive evaluation of composites, NDE of concrete, non destructive evaluation of stresses, NDE of defects, condition monitoring, vibration monitoring, life prediction and NDE for medical applications. Papers relevant to INIS from this volume are indexed separately

Trends in NDE science and technology: proceedings of the fourteenth world conference on NDT. V. 3

International Nuclear Information System (INIS)

Krishnadas Nair, C.G.; Baldev Raj; Murthy, C.R.L.; Jayakumar, T.

1996-01-01

The multi volume proceedings of the 14th World Conference on Nondestructive Testing (NDT) cover the applications of Non destructive Evaluation (NDE) in a wide range of industries, viz. aerospace, chemical, defence, manufacturing, nuclear etc. and for different materials. The major topics covered under it are NDE in nuclear industry, NDE of tubes and bars, non destructive evaluation of composites, NDE of concrete, non destructive evaluation of stresses, NDE of defects, condition monitoring, vibration monitoring, life prediction and NDE for medical applications. Papers relevant to INIS from this volume are indexed separately

Trends in NDE science and technology: proceedings of the fourteenth world conference on NDT. V. 2

International Nuclear Information System (INIS)

Krishnadas Nair, C.G.; Baldev Raj; Murthy, C.R.L.; Jayakumar, T.

1996-01-01

The multi volume proceedings of the 14th World Conference on Nondestructive Testing (NDT) cover the applications of Nondestructive Evaluation (NDE) in a wide range of industries, viz. aerospace, chemical, defence, manufacturing, nuclear etc. and for different materials. The major topics covered under it are NDE in nuclear industry, NDE of tubes and bars, non destructive evaluation of composites, NDE of concrete, non destructive evaluation of stresses, NDE of defects, condition monitoring, vibration monitoring, life prediction and NDE for medical applications. Papers relevant to INIS from this volume are indexed separately

Trends in NDE science and technology: proceedings of the fourteenth world conference on NDT. V. 4

International Nuclear Information System (INIS)

Krishnadas Nair, C.G.; Baldev Raj; Murthy, C.R.L.; Jayakumar, T.

1996-01-01

The multi volume proceedings of the 14th World Conference on Nondestructive Testing (NDT) cover the applications of Nondestructive Evaluation (NDE) in a wide range of industries, viz. aerospace, chemical, defence, manufacturing, nuclear etc. and for different materials. The major topics covered under it are NDE in nuclear industry, NDE of tubes and bars, non destructive evaluation of composites, NDE of concrete, non destructive evaluation of stresses, NDE of defects, condition monitoring, vibration monitoring, life prediction and NDE for medical applications. Papers relevant to INIS from this volume are indexed separately

Trends in NDE science and technology: proceedings of the fourteenth world conference on NDT V. 5

International Nuclear Information System (INIS)

Krishnadas Nair, C.J.; Baldev Raj; Murthy, C.R.L.; Jayakumar, T.

1996-01-01

The multi volume proceedings of the 14th World Conference on Nondestructive Testing (NDT) cover the applications of Nondestructive Evaluation (NDE) in a wide range of industries, viz. aerospace, chemical, defence, manufacturing, nuclear etc. and for different materials. The major topics covered under it are NDE in nuclear industry, NDE of tubes and bars, non destructive evaluation of composites, NDE of concrete, non destructive evaluation of stresses, NDE of defects, condition monitoring, vibration monitoring, life prediction and NDE for medical applications. Papers relevant to INIS from this volume are indexed separately

The state-of-the Art of the Established Conventional and Advanced NDE-Techniques and Procedures for Defect Detection and Sizing - Part D: application of ultrasonic techniques for the inspection of austenitic components

International Nuclear Information System (INIS)

Edelmann, X.

1997-01-01

Ultrasonic examination of austenitic welds is possible in many cases but special techniques have often to be applied. The 'Handbook on the Ultrasonic Examination of Austenitic Welds' of the International Institute of Welding gives advice how to devise procedures for the detection, location and evaluation of ultrasonic indications of weld defects. In most circumstances it is necessary to use angled longitudinal wave probes. Austenitic weld examination is more complex and more expensive than ferritic weld examination. Detection and characterization of intergranular stress corrosion cracking has been improved by special qualification programs of the EPRI NDE Center. Dissimilar Metal welds are difficult to examine. Techniques have been developed for detection of circumferential and axial defects. Cast stainless steel structures are in general still extremely difficult to examine as a recent round robin test of the PISC program has shown. Mechanized examination with adequate data acquisition processing and presentation techniques enables better interpretation of examination results. (author)

Frontiers in NDE research nearing maturity for exploitation to ensure structural integrity of pressure retaining components

International Nuclear Information System (INIS)

Raj, Baldev; Mukhopadhyay, C.K.; Jayakumar, T.

2006-01-01

In this paper, research and developmental efforts that demonstrate high sensitivity detection and characterization of defects and assessment of microstructural degradation, residual stresses and fatigue damage in materials using different non-destructive evaluation (NDE) techniques, have been discussed. Applications of eddy current techniques for quantitative defect characterization and for generalized applications, and remote field eddy current technique for inspection of steam generator and heat exchanger tubes have been discussed. Advanced ultrasonic methods such as time of flight diffraction, synthetic aperture focusing technique, phased array and signal processing for detection, characterization and imaging of defects have been discussed. Applications of ultrasonics and magnetic Barkhausen emission techniques for characterization of microstructures and residual stresses have been discussed. Applications of acoustic emission and infrared thermography techniques for weld quality evaluation of critical nuclear components as part of intelligent processing of materials (IPM) work have been discussed. Application of acoustic emission technique for integrity assessment of pressurized components has been discussed. Development of a software called assets and infrastructure management system (AIMS), for storing and retrieving information for various materials, components and systems, has also been highlighted. The techniques and applications discussed are result of systematic and innovative R and D efforts in the multidisciplinary areas of physics, materials, instrumentation, sensors and softwares for providing solutions to various challenging problems

Terahertz NDE application for corrosion detection and evaluation under Shuttle tiles

Science.gov (United States)

Anastasi, Robert F.; Madaras, Eric I.; Seebo, Jeffrey P.; Smith, Stephen W.; Lomness, Janice K.; Hintze, Paul E.; Kammerer, Catherine C.; Winfree, William P.; Russell, Richard W.

2007-04-01

Pulsed Terahertz NDE is being examined as a method to inspect for possible corrosion under Space Shuttle Tiles. Other methods such as ultrasonics, infrared, eddy current and microwave technologies have demonstrable shortcomings for tile NDE. This work applies Terahertz NDE, in the frequency range between 50 GHz and 1 THz, for the inspection of manufactured corrosion samples. The samples consist of induced corrosion spots that range in diameter (2.54 to 15.2 mm) and depth (0.036 to 0.787 mm) in an aluminum substrate material covered with tiles. Results of these measurements are presented for known corrosion flaws both covered and uncovered and for blind tests with unknown corrosion flaws covered with attached tiles. The Terahertz NDE system is shown to detect all artificially manufactured corrosion regions under a Shuttle tile with a depth greater than 0.13 mm.

Nondestructive techniques for characterizing mechanical properties of structural materials: An overview

Science.gov (United States)

Vary, A.; Klima, S. J.

1985-01-01

An overview of nondestructive evaluation (NDE) is presented to indicate the availability and application potentials of techniques for quantitative characterization of the mechanical properties of structural materials. The purpose is to review NDE techniques that go beyond the usual emphasis on flaw detection and characterization. Discussed are current and emerging NDE techniques that can verify and monitor entrinsic properties (e.g., tensile, shear, and yield strengths; fracture toughness, hardness, ductility; elastic moduli) and underlying microstructural and morphological factors. Most of the techniques described are, at present, neither widely applied nor widely accepted in commerce and industry because they are still emerging from the laboratory. The limitations of the techniques may be overcome by advances in applications research and instrumentation technology and perhaps by accommodations for their use in the design of structural parts.

Evaluation of pipe weld NDE indications

International Nuclear Information System (INIS)

Brasse, M.

2007-01-01

This paper discusses the evaluation of non-destructive examination (NDE) indications in pipe welds. The evaluation procedure is described in a practical engineer's view and examples are also given. (author)

Proceedings: 20th Steam Generator NDE Workshop: Orlando, Florida, July 9-11, 2001

International Nuclear Information System (INIS)

2003-01-01

The 2001 workshop took place in Orlando, Florida, from July 9 to 11, 2001. It covered one full day and two half-days of presentations. Attendees included representatives from domestic and overseas nuclear utilities, NSSS vendors, NDE service and equipment organizations, research laboratories, and regulatory bodies. This annual workshop serves as a forum for NDE specialists to gather and discuss current steam generator NDE issues and means for their resolution

Rocket center Peenemünde — Personal memories

Science.gov (United States)

Dannenberg, Konrad; Stuhlinger, Ernst

Von Braun built his first rockets as a young teenager. At 14, he started making plans for rockets for human travel to the Moon and Mars. The German Army began a rocket program in 1929. Two years later, Colonel (later General) Becker contacted von Braun who experimented with rockets in Berlin, gave him a contract in 1932, and, jointly with the Air Force, in 1936 built the rocket center Peenemünde where von Braun and his team developed the A-4 (V-2) rocket under Army auspices, while the Air Force developed the V-1 (buzz bomb), wire-guided bombs, and rocket planes. Albert Speer, impressed by the work of the rocketeers, allowed a modest growth of the Peenemünde project; this brought Dannenberg to the von Braun team in 1940. Hitler did not believe in rockets; he ignored the A-4 project until 1942 when he began to support it, expecting that it could turn the fortunes of war for him. He drastically increased the Peenemünde work force and allowed the transfer of soldiers from the front to Peenemünde; that was when Stuhlinger, in 1943, came to Peenemünde as a Pfc.-Ph.D. Later that year, Himmler wrenched the authority over A-4 production out of the Army's hands, put it under his command, and forced production of the immature rocket at Mittelwerk, and its military deployment against targets in France, Belgium, and England. Throughout the development of the A-4 rocket, von Braun was the undisputed leader of the project. Although still immature by the end of the war, the A-4 had proceeded to a status which made it the first successful long-range precision rocket, the prototype for a large number of military rockets built by numerous nations after the war, and for space rockets that launched satellites and traveled to the Moon and the planets.

The role of NDE in maintaining and extending the life cycle of engineering components

International Nuclear Information System (INIS)

Doctor, S.R.

1997-01-01

A successful life cycle of engineering components begins during the design to select the best materials for a given application, designing for economical maintenance, and accommodating NDE inspections. NDE in the nuclear industry is part of the defense in depth to insure structural integrity of components. High reliability NDE is needed to reliably detect and accurately characterize the failure modes that have occurred in nuclear components. The move toward risk-informed inservice inspection programs focusses the NDE on the most safety significant components. The use of performance demonstration testing is leading to improved inservice inspections through screening out ineffective procedure/equipment/personnel. (orig.)

Nuclear Technology. Course 32: Nondestructive Examination (NDE) II. Module 32-3, Fundamentals of Magnetic Particle Testing.

Science.gov (United States)

Groseclose, Richard

This third in a series of six modules for a course titled Nondestructive Examination (NDE) Techniques II explains the principles of magnets and magnetic fields and how they are applied in magnetic particle testing, describes the theory and methods of magnetizing test specimens, describes the test equipment used, discusses the principles and…

An overview of the NDE Center - The first decade

International Nuclear Information System (INIS)

Dau, G.J.

1990-01-01

The EPRI NDE Center was established in 1979 to provide the electrical utility industry with a dedicated NDE capability. The Center's role was defined as providing a bridge to transfer the research and development results generated by EPRI R and D programs (as well as other funding agencies) into qualified equipment and procedures in the shortest possible time. The mission is pursued through three distinct thrusts: technology transfer, training, and resource development. Technology transfer is usually accomplished by a combination of equipment and procedure evaluations and demonstrations. Specific training programs are developed to meet the specific needs of the utility industry. One feature of these programs is the reliance on realistic samples during the training programs. Resource development is oriented toward encouraging more people to pursue NDE as a career. This thrust is implemented by working with interested educational institutions to develop appropriate materials. Work in this project divides naturally into technology and training areas. NDE technology work is focused on improving the inspections applied to heat exchangers, piping, steam turbines, and heavy-section components such as the reactor pressure vessel. Training activities involve the provision of formal courses when a large number of people must become proficient in an improved technology. More details on each of these areas are given in sections that immediately follow

Micro- and nano-NDE systems for aircraft: great things in small packages

Science.gov (United States)

Malas, James C.; Kropas-Hughes, Claudia V.; Blackshire, James L.; Moran, Thomas; Peeler, Deborah; Frazier, W. G.; Parker, Danny

2003-07-01

Recent advancements in small, microscopic NDE sensor technologies will revolutionize how aircraft maintenance is done, and will significantly improve the reliability and airworthiness of current and future aircraft systems. A variety of micro/nano systems and concepts are being developed that will enable whole new capabilities for detecting and tracking structural integrity damage. For aging aircraft systems, the impact of micro-NDE sensor technologies will be felt immediately, with dramatic reductions in labor for maintenance, and extended useable life of critical components being two of the primary benefits. For the fleet management of future aircraft systems, a comprehensive evaluation and tracking of vehicle health throughout its entire life cycle will be needed. Indeed, micro/nano NDE systems will be instrumental in realizing this futuristic vision. Several major challenges will need to be addressed, however, before micro- and nano-NDE systems can effectively be implemented, and this will require interdisciplinary research approaches, and a systematic engineering integration of the new technologies into real systems. Future research will need to emphasize systems engineering approaches for designing materials and structures with in-situ inspection and prognostic capabilities. Recent advances in 1) embedded / add-on micro-sensors, 2) computer modeling of nondestructive evaluation responses, and 3) wireless communications are important steps toward this goal, and will ultimately provide previously unimagined opportunities for realizing whole new integrated vehicle health monitoring capabilities. The future use of micro/nano NDE technologies as vehicle health monitoring tools will have profound implications, and will provide a revolutionary way of doing NDE in the near and distant future.

An NDE Approach for Characterizing Quality Problems in Polymer Matrix Composites

Science.gov (United States)

Roth, Don J.; Baaklini, George Y.; Sutter, James K.; Bodis, James R.; Leonhardt, Todd A.; Crane, Elizabeth A.

1994-01-01

Polymer matrix composite (PMC) materials are periodically identified appearing optically uniform but containing a higher than normal level of global nonuniformity as indicated from preliminary ultrasonic scanning. One such panel was thoroughly examined by nondestructive (NDE) and destructive methods to quantitatively characterize the nonuniformity. The NDE analysis of the panel was complicated by the fact that the panel was not uniformly thick. Mapping of ultrasonic velocity across a region of the panel in conjunction with an error analysis was necessary to (1) characterize properly the porosity gradient that was discovered during destructive analyses and (2) account for the thickness variation effects. Based on this study, a plan for future NDE characterization of PMC's is presented to the PMC community.

Inspection of copper canisters for spent nuclear fuel by means of ultrasound. NDE of friction stir welds, nonlinear acoustics, ultrasonic imaging

Energy Technology Data Exchange (ETDEWEB)

Stepinski, Tadeusz (ed.); Lingvall, Fredrik; Wennerstroem, Erik; Ping Wu [Uppsala Univ., Dept. of Materials Science (Sweden). Signals and Systems

2004-01-01

This report contains results concerning advanced ultrasound for the inspection of copper canisters for spent nuclear fuel obtained at Signals and Systems, Uppsala University in years 2002/2003. After a short introduction a review of the NDE techniques that have been applied to the assessment of friction stir welds (FSW) is presented. The review is based on the results reported by the specialists from the USA, mostly from the aerospace industry. A separate chapter is devoted to the extended experimental and theoretical research concerning potential of nonlinear waves in NDE applications. Further studies concerning nonlinear propagation of acoustic and elastic waves (classical nonlinearity) are reported. Also a preliminary investigation of the nonlinear ultrasonic detection of contacts and interfaces (non-classical nonlinearity) is included. Report on the continuation of previous work concerning computer simulation of nonlinear propagations of ultrasonic beams in water and in immersed solids is also presented. Finally, results of an investigation concerning a new method of synthetic aperture imaging (SAI) and its comparison to the traditional phased array (PA) imaging and to the synthetic aperture focusing technique (SAFT) are presented. A new spatial-temporal filtering method is presented that is a generalization of the previously proposed filter. Spatial resolution of the proposed method is investigated and compared experimentally to that of classical SAFT and PA imaging. Performance of the proposed method for flat targets is also investigated.

Inspection of copper canisters for spent nuclear fuel by means of ultrasound. NDE of friction stir welds, nonlinear acoustics, ultrasonic imaging

International Nuclear Information System (INIS)

Stepinski, Tadeusz; Lingvall, Fredrik; Wennerstroem, Erik; Ping Wu

2004-01-01

This report contains results concerning advanced ultrasound for the inspection of copper canisters for spent nuclear fuel obtained at Signals and Systems, Uppsala University in years 2002/2003. After a short introduction a review of the NDE techniques that have been applied to the assessment of friction stir welds (FSW) is presented. The review is based on the results reported by the specialists from the USA, mostly from the aerospace industry. A separate chapter is devoted to the extended experimental and theoretical research concerning potential of nonlinear waves in NDE applications. Further studies concerning nonlinear propagation of acoustic and elastic waves (classical nonlinearity) are reported. Also a preliminary investigation of the nonlinear ultrasonic detection of contacts and interfaces (non-classical nonlinearity) is included. Report on the continuation of previous work concerning computer simulation of nonlinear propagations of ultrasonic beams in water and in immersed solids is also presented. Finally, results of an investigation concerning a new method of synthetic aperture imaging (SAI) and its comparison to the traditional phased array (PA) imaging and to the synthetic aperture focusing technique (SAFT) are presented. A new spatial-temporal filtering method is presented that is a generalization of the previously proposed filter. Spatial resolution of the proposed method is investigated and compared experimentally to that of classical SAFT and PA imaging. Performance of the proposed method for flat targets is also investigated

Automated NDE Flaw Mapping System, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — NASA's Aircraft Aging and Durability Project (AADP) aims to ensure the safety of both commercial and military aviation aircraft. Non-destructive evaluation (NDE)...

NDE reliability and probability of detection (POD) evolution and paradigm shift

Energy Technology Data Exchange (ETDEWEB)

Singh, Surendra [NDE Engineering, Materials and Process Engineering, Honeywell Aerospace, Phoenix, AZ 85034 (United States)

2014-02-18

The subject of NDE Reliability and POD has gone through multiple phases since its humble beginning in the late 1960s. This was followed by several programs including the important one nicknamed “Have Cracks – Will Travel” or in short “Have Cracks” by Lockheed Georgia Company for US Air Force during 1974–1978. This and other studies ultimately led to a series of developments in the field of reliability and POD starting from the introduction of fracture mechanics and Damaged Tolerant Design (DTD) to statistical framework by Bernes and Hovey in 1981 for POD estimation to MIL-STD HDBK 1823 (1999) and 1823A (2009). During the last decade, various groups and researchers have further studied the reliability and POD using Model Assisted POD (MAPOD), Simulation Assisted POD (SAPOD), and applying Bayesian Statistics. All and each of these developments had one objective, i.e., improving accuracy of life prediction in components that to a large extent depends on the reliability and capability of NDE methods. Therefore, it is essential to have a reliable detection and sizing of large flaws in components. Currently, POD is used for studying reliability and capability of NDE methods, though POD data offers no absolute truth regarding NDE reliability, i.e., system capability, effects of flaw morphology, and quantifying the human factors. Furthermore, reliability and POD have been reported alike in meaning but POD is not NDE reliability. POD is a subset of the reliability that consists of six phases: 1) samples selection using DOE, 2) NDE equipment setup and calibration, 3) System Measurement Evaluation (SME) including Gage Repeatability and Reproducibility (Gage R and R) and Analysis Of Variance (ANOVA), 4) NDE system capability and electronic and physical saturation, 5) acquiring and fitting data to a model, and data analysis, and 6) POD estimation. This paper provides an overview of all major POD milestones for the last several decades and discuss rationale for using

Automated NDE Flaw Mapping System, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — The prevailing approach to non-destructive evaluation (NDE) of aircraft components is to set an inspection schedule based on what is generally known about the...

Three-dimensional NDE of VHTR core components via simulation-based testing. Final report

International Nuclear Information System (INIS)

Guzina, Bojan; Kunerth, Dennis

2014-01-01

A next generation, simulation-driven-and-enabled testing platform is developed for the 3D detection and characterization of defects and damage in nuclear graphite and composite structures in Very High Temperature Reactors (VHTRs). The proposed work addresses the critical need for the development of high-fidelity Non-Destructive Examination (NDE) technologies for as-manufactured and replaceable in-service VHTR components. Centered around the novel use of elastic (sonic and ultrasonic) waves, this project deploys a robust, non-iterative inverse solution for the 3D defect reconstruction together with a non-contact, laser-based approach to the measurement of experimental waveforms in VHTR core components. In particular, this research (1) deploys three-dimensional Scanning Laser Doppler Vibrometry (3D SLDV) as a means to accurately and remotely measure 3D displacement waveforms over the accessible surface of a VHTR core component excited by mechanical vibratory source; (2) implements a powerful new inverse technique, based on the concept of Topological Sensitivity (TS), for non-iterative elastic waveform tomography of internal defects - that permits robust 3D detection, reconstruction and characterization of discrete damage (e.g. holes and fractures) in nuclear graphite from limited-aperture NDE measurements; (3) implements state-of-the art computational (finite element) model that caters for accurately simulating elastic wave propagation in 3D blocks of nuclear graphite; (4) integrates the SLDV testing methodology with the TS imaging algorithm into a non-contact, high-fidelity NDE platform for the 3D reconstruction and characterization of defects and damage in VHTR core components; and (5) applies the proposed methodology to VHTR core component samples (both two- and three-dimensional) with a priori induced, discrete damage in the form of holes and fractures. Overall, the newly established SLDV-TS testing platform represents a next-generation NDE tool that surpasses

Three-dimensional NDE of VHTR core components via simulation-based testing. Final report

Energy Technology Data Exchange (ETDEWEB)

Guzina, Bojan [Univ. of Minnesota, Minneapolis, MN (United States); Kunerth, Dennis [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2014-09-30

A next generation, simulation-driven-and-enabled testing platform is developed for the 3D detection and characterization of defects and damage in nuclear graphite and composite structures in Very High Temperature Reactors (VHTRs). The proposed work addresses the critical need for the development of high-fidelity Non-Destructive Examination (NDE) technologies for as-manufactured and replaceable in-service VHTR components. Centered around the novel use of elastic (sonic and ultrasonic) waves, this project deploys a robust, non-iterative inverse solution for the 3D defect reconstruction together with a non-contact, laser-based approach to the measurement of experimental waveforms in VHTR core components. In particular, this research (1) deploys three-dimensional Scanning Laser Doppler Vibrometry (3D SLDV) as a means to accurately and remotely measure 3D displacement waveforms over the accessible surface of a VHTR core component excited by mechanical vibratory source; (2) implements a powerful new inverse technique, based on the concept of Topological Sensitivity (TS), for non-iterative elastic waveform tomography of internal defects - that permits robust 3D detection, reconstruction and characterization of discrete damage (e.g. holes and fractures) in nuclear graphite from limited-aperture NDE measurements; (3) implements state-of-the art computational (finite element) model that caters for accurately simulating elastic wave propagation in 3D blocks of nuclear graphite; (4) integrates the SLDV testing methodology with the TS imaging algorithm into a non-contact, high-fidelity NDE platform for the 3D reconstruction and characterization of defects and damage in VHTR core components; and (5) applies the proposed methodology to VHTR core component samples (both two- and three-dimensional) with a priori induced, discrete damage in the form of holes and fractures. Overall, the newly established SLDV-TS testing platform represents a next-generation NDE tool that surpasses

DISC1, PDE4B, and NDE1 at the centrosome and synapse

International Nuclear Information System (INIS)

Bradshaw, Nicholas J.; Ogawa, Fumiaki; Antolin-Fontes, Beatriz; Chubb, Jennifer E.; Carlyle, Becky C.; Christie, Sheila; Claessens, Antoine; Porteous, David J.; Millar, J. Kirsty

2008-01-01

Disrupted-In-Schizophrenia 1 (DISC1) is a risk factor for schizophrenia and other major mental illnesses. Its protein binding partners include the Nuclear Distribution Factor E Homologs (NDE1 and NDEL1), LIS1, and phosphodiesterases 4B and 4D (PDE4B and PDE4D). We demonstrate that NDE1, NDEL1 and LIS1, together with their binding partner dynein, associate with DISC1, PDE4B and PDE4D within the cell, and provide evidence that this complex is present at the centrosome. LIS1 and NDEL1 have been previously suggested to be synaptic, and we now demonstrate localisation of DISC1, NDE1, and PDE4B at synapses in cultured neurons. NDE1 is phosphorylated by cAMP-dependant Protein Kinase A (PKA), whose activity is, in turn, regulated by the cAMP hydrolysis activity of phosphodiesterases, including PDE4. We propose that DISC1 acts as an assembly scaffold for all of these proteins and that the NDE1/NDEL1/LIS1/dynein complex is modulated by cAMP levels via PKA and PDE4.

NDE research at NASA Langley Research Center

International Nuclear Information System (INIS)

Heyman, J.S.

1989-01-01

The Nondestructive Measurement Science Branch at NASA Langley is the Agency's lead Center for NDE research. The focus of the laboratory is to improve the science base for NDE, evolve a more quantitative, interpretable technology to insure safety and reliability, and transfer that technology to the commercial sector. To address the broad needs of the Agency, the program has developed expertise in many areas, some of which are in ultrasonics, nonlinear acoustics, nano and microstructure characterization, thermal NDE, x-ray tomography, optical fiber sensors, magnetic probing, process monitoring sensors, and image/signal processing. The authors laboratory has recently dedicated its new 20,000 square foot research facility bringing the lab space to 30,000 square feet. The new facility includes a high bay for the x-ray CAT scanner, a revolutionary new concept in materials measurement. The CAT scanner is called QUEST, for quantitative experimental stress tomography lab. This system combines for the first time a microfocus x-ray source and detector with a fatigue load frame. Three dimensional imaging of density/geometry of the tested sample is thus possible during tension/compression loading. This system provides the first 3-D view of crack initiation, crack growth, phase transformation, bonded surface failure, creep-all with a density sensitivity of 0.1% and a resolution of about 25 microns (detectability of about 1 micron)

NDE Technology Development Program for Non-Visual Volumetric Inspection Technology; Sensor Effectiveness Testing Report

Energy Technology Data Exchange (ETDEWEB)

Moran, Traci L. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Larche, Michael R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Denslow, Kayte M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Glass, Samuel W. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2017-08-31

The Pacific Northwest National Laboratory (PNNL) located in Richland, Washington, hosted and administered Sensor Effectiveness Testing that allowed four different participants to demonstrate the NDE volumetric inspection technologies that were previously demonstrated during the Technology Screening session. This document provides a Sensor Effectiveness Testing report for the final part of Phase I of a three-phase NDE Technology Development Program designed to identify and mature a system or set of non-visual volumetric NDE technologies for Hanford DST primary liner bottom inspection. Phase I of the program will baseline the performance of current or emerging non-visual volumetric NDE technologies for their ability to detect and characterize primary liner bottom flaws, and identify candidate technologies for adaptation and maturation for Phase II of the program.

Development of a Remotely Operated NDE System for Inspection of Hanford's Double Shell Waste Tank Knuckle Regions

International Nuclear Information System (INIS)

Pardini, Allan F; Alzheimer, James M; Crawford, Susan L; Diaz, Aaron A; Gervais, Kevin L; Harris, Robert V; Riechers, Douglas M; Samuel, Todd J; Schuster, George J; Tucker, Joseph C

2001-01-01

This report documents work performed at the PNNL in FY01 to support development of a Remotely Operated NDE (RONDE) system capable of inspecting the knuckle region of Hanford's DSTs. The development effort utilized commercial off-the-shelf (COTS) technology wherever possible and provided a transport and scanning device for implementing the SAFT and T-SAFT techniques

Standard compliance - NDE performance demonstration/inspection in the CANDU industry

International Nuclear Information System (INIS)

Choi, E.

2011-01-01

CANDU nuclear power plants are operated in 3 provinces in Canada for electric power generation. A table in the paper will show the built and operating plants in Ontario, Quebec, New Brunswick and overseas. The regulator for nuclear power in Canada is the Canadian Nuclear Safety Commission (CNSC). The CNSC holds the plant licensees accountable for compliance to CSA N285.4 for periodic inspections. The Standard basically specifies the 'what, when, where, how, how much and how frequently' NDE is to be done on pressure retaining systems and components in CANDU nuclear power plants. In inspection methods, the Standard specifies they must be non-destructive. The NDE methods were grouped into visual, dimensional, surface, volumetric and integrative. The Standard also specifies that the licensees are responsible for the performance demonstration (PD) of the adequacy of the procedures and the proficiency of the personnel. This paper describes the Standard's requirement in NDE qualification and presents a joint project participated by Canadian and overseas CANDU owners. The sub-project for NDE included providing evidence and technical justification on the adequacy of the procedures and the proficiency of the personnel. The paper describes the qualification methodology followed by the participants. This will be followed by how the participants produced Inspection Specification, tools and procedures, personnel training and qualification programs, test and qualification samples, independent peer reviews and Technical Justification. (author)

Final report on the development of a disturbanceless NDE compact cooling device; Abschlussbericht zur Entwicklung einer stoerarmen maschinellen NDE-Kompaktkuehlung

Energy Technology Data Exchange (ETDEWEB)

Kaiser, G.

2002-08-13

The project comprised the following aspects: 1. Development of a disturbance-free, mechanized compact cooling system for a NDE measuring system on the basis of a commercial SL200-10 split stirling cooling system of AEG Infrarotmodule GmbH, Heilbronn; 2. Support of the development work at the HTSL/Hall magnetometer of Friedrich-Schiller University, Jena; 3. Measurements of HTSL/Hall magnetometer samples and thermal characterisation. [German] Im Rahmen dieses Vorhabens wurden die folgenden Aufgabenstellungen behandelt: 1. Entwicklung einer stoerarmen, maschinellen Kompaktkuehlung fuer ein NDE-Messsystem auf der Basis eines kommerziellen Split-Stirlingkuehlers SL200-10 der Firma AEG Infrarotmodule GmbH, Heilbronn, 2. Unterstuetzung der Entwicklungsarbeiten am HTSL/Hall-Magnetometer, die bei der Friedrich-Schiller-Universitaet in Jena durchgefuehrt wurden, 3. Messungen an HTSL/Hall-Magnetometer-Proben zu deren thermischer Charakterisierung. (orig.)

Evaluation of creep-fatigue crack growth for large-scale FBR reactor vessel and NDE assessment

Energy Technology Data Exchange (ETDEWEB)

Joo, Young Sang; Kim, Jong Bum; Kim, Seok Hun; Yoo, Bong

2001-03-01

Creep fatigue crack growth contributes to the failure of FRB reactor vessels in high temperature condition. In the design stage of reactor vessel, crack growth evaluation is very important to ensure the structural safety and setup the in-service inspection strategy. In this study, creep-fatigue crack growth evaluation has been performed for the semi-elliptical surface cracks subjected to thermal loading. The thermal stress analysis of a large-scale FBR reactor vessel has been carried out for the load conditions. The distributions of axial, radial, hoop, and Von Mises stresses were obtained for the loading conditions. At the maximum point of the axial and hoop stress, the longitudinal and circumferential surface cracks (i.e. PTS crack, NDE short crack and shallow long crack) were postulated. Using the maximum and minimum values of stresses, the creep-fatigue crack growth of the proposed cracks was simulated. The crack growth rate of circumferential cracks becomes greater than that of longitudinal cracks. The total crack growth of the largest PTS crack is very small after 427 cycles. The structural integrity of a large-scale reactor can be maintained for the plant life. The crack depth growth of the shallow long crack is faster than that of the NDE short crack. In the ISI of the large-scale FBR reactor vessel, the ultrasonic inspection is beneficial to detect the shallow circumferential cracks.

An ultrasonic technique for predicting tensile strength of southern pine lumber

Science.gov (United States)

D. Rajeshwar; D.A. Bender; D.E. Bray; K.A. McDonald

1997-01-01

The goal of this research was to develop nondestructive evaluation (NDE) technology to enhance mechanical stress rating of lumber. An ultrasonic NDE technique was developed that is sensitive to grain angle and edge knots in lumber - two primary determinants of lumber strength. The presence of edge knots increased the acoustic wave travel time and selectively...

40-in. OMS Kevlar(Registered Trademark) COPV S/N 007 Stress Rupture Test NDE

Science.gov (United States)

Saulsberry, Regor; Greene, Nate; Forth, Scott; Leifeste, Mark; Gallus, Tim; Yoder, Tommy; Keddy, Chris; Mandaras, Eric; Wincheski, Buzz; Williams, Philip;

Feasibility study on infrared electro-thermal NDE of stainless steel

International Nuclear Information System (INIS)

Green, D.R.; Hassberger, J.A.

1975-11-01

Electro-thermal examination, a branch of thermal testing (TT), is a promising method being developed for NDE of stainless steel welds. This report describes the first phase of development; i.e., preliminary demonstration and laboratory evaluation of the method's sensitivity to notches in Type 304 stainless steel plate specimens. It also includes a description of the basic principles, together with a description of the hardware and experimental results showing that electrical discharge machined notches down to 0.16 cm (0.06 in.) long x 0.08 cm (0.03 in.) deep were detected. A qualitative technique for interpreting the test results to determine whether defects are at the surface or deeper within the material is demonstrated

NDE of stresses in thick-walled components by ultrasonic methods

International Nuclear Information System (INIS)

Goebbels, K.; Pitsch, H.; Schneider, E.; Nowack, H.

1985-01-01

The possibilty of measuring stresses - especially residual stresses - by ultrasonic methods has been presented at the 4th and 5th International Conference on NDE in Nuclear Industry. This contribution now presents results of several applications to thick walled components such as turbines and generators for power plants. The measurement technique using linearly polarized shear waves allows one to characterize the homogeneitry of the residual stress situation along and around cylindrically shaped components. Some important results show that the stress distribution integrated over the cross section of the component has not followed in any case the simple relations derived by stress analysts. Conclusions referring to the stress situation inside the components are discussed

Nondestructive Testing Technique to Quantify Deterioration from Marine Borer Attack in Sitka Spruce and Western Hemlock Logs: Observations from a Pilot Test

Science.gov (United States)

Robert Ross; John W. Forsman; John R. Erickson; Allen M. Brackley

2014-01-01

Stress-wave nondestructive evaluation (NDE) techniques are used widely in the forest products industry—from the grading of wood veneer to inspection of timber structures. Inspection professionals frequently use stress-wave NDE techniques to locate internal voids and decayed or deteriorated areas in large timbers. Although these techniques have proven useful, little...

NASA DOE POD NDE Capabilities Data Book

Science.gov (United States)

Generazio, Edward R.

2015-01-01

This data book contains the Directed Design of Experiments for Validating Probability of Detection (POD) Capability of NDE Systems (DOEPOD) analyses of the nondestructive inspection data presented in the NTIAC, Nondestructive Evaluation (NDE) Capabilities Data Book, 3rd ed., NTIAC DB-97-02. DOEPOD is designed as a decision support system to validate inspection system, personnel, and protocol demonstrating 0.90 POD with 95% confidence at critical flaw sizes, a90/95. The test methodology used in DOEPOD is based on the field of statistical sequential analysis founded by Abraham Wald. Sequential analysis is a method of statistical inference whose characteristic feature is that the number of observations required by the procedure is not determined in advance of the experiment. The decision to terminate the experiment depends, at each stage, on the results of the observations previously made. A merit of the sequential method, as applied to testing statistical hypotheses, is that test procedures can be constructed which require, on average, a substantially smaller number of observations than equally reliable test procedures based on a predetermined number of observations.

Use of computerized data acquisition system to auralize NDE data for improved inspection capability

International Nuclear Information System (INIS)

Light, Glenn M.; Holt, Amos E.; Polk, Kent D.; Clayton, William T.

2004-01-01

Southwest Research Institute has developed computer-aided technology for converting electronic signals generated by conventional nondestructive evaluation (NDE) equipment (i.e., ultrasonic, eddy current, and acoustic emission) into audible information so that the inspector can make use of both the conventional NDE signals (which are often confusing) and the audible information to make a flaw/nonflaw decision. One objective of this work was to develop a computerized data acquisition system that could collect ultrasonic data, perform time dilation of the ultrasonic data, and help develop algorithms. The aural technology has been applied to composite impact damage, composite delamination detection, and corrosion detection. In addition, the aural technology was used to detect and discriminate intergranular stress corrosion cracking. Examples of application of aural NDE technology are described. (author)

Swept frequency acoustic interferometry technique for chemical weapons verification and monitoring

Energy Technology Data Exchange (ETDEWEB)

Sinha, D.N.; Anthony, B.W.; Lizon, D.C.

1995-03-01

Nondestructive evaluation (NDE) techniques are important for rapid on-site verification and monitoring of chemical munitions, such as artillery shells and bulk containers. Present NDE techniques provide only limited characterizations of such munitions. This paper describes the development of a novel noninvasive technique, swept-frequency acoustic interferometry (SFAI), that significantly enhances the capability of munitions characterizations. The SFAI technique allows very accurate and simultaneous determination of sound velocity and attenuation of chemical agents over a large frequency range inside artillery shells, in addition to determining agent density. The frequency-dependent sound velocity and attenuation can, in principle, provide molecular relaxation properties of the chemical agent. The same instrument also enables a direct fill-level measurement in bulk containers. Industrial and other applications of this general-purpose technique are also discussed.

NDE of stainless steel and on-line leak monitoring of LWRs. Annual report, October 1983-September 1984

International Nuclear Information System (INIS)

Kupperman, D.S.; Claytor, T.N.; Prine, D.W.

1985-04-01

The application of ultrasonic velocity and attenuation measurements to characterize the microstructure of structural materials is discussed. Results of a workshop on NDE of stainless steel pipes with weld overlays are presented. No currently available, single leak-detection method for reactor cooling systems combines optimal leakage detection sensitivity, leak-locating ability, and leakage measurement accuracy. Current practice with regard to leak detection has been reviewed and assessed for 74 operating plants, including both BWRs and PWRs. Seven cracks, including three field-induced IGSCC specimens and two thermal-fatigue cracks, have been installed in the acoustic leak detection (ALD) facility at ANL. Cross-correlation techniques to improve leak location capabilities have been successfully demonstrated on the laboratory pipe run by use of 375-kHz transducers on waveguides and an electronically simulated leak signal. Preliminary leak detection and location tests have also been run at ANL with a breadboard ALD system. In addition to ALD experiments, laboratory tests have been carried out to help assess the effectiveness of moisture-sensitive tape

Ultrasonic NDE Simulation for Composite Manufacturing Defects

Science.gov (United States)

Leckey, Cara A. C.; Juarez, Peter D.

2016-01-01

The increased use of composites in aerospace components is expected to continue into the future. The large scale use of composites in aerospace necessitates the development of composite-appropriate nondestructive evaluation (NDE) methods to quantitatively characterize defects in as-manufactured parts and damage incurred during or post manufacturing. Ultrasonic techniques are one of the most common approaches for defect/damage detection in composite materials. One key technical challenge area included in NASA's Advanced Composite's Project is to develop optimized rapid inspection methods for composite materials. Common manufacturing defects in carbon fiber reinforced polymer (CFRP) composites include fiber waviness (in-plane and out-of-plane), porosity, and disbonds; among others. This paper is an overview of ongoing work to develop ultrasonic wavefield based methods for characterizing manufacturing waviness defects. The paper describes the development and implementation of a custom ultrasound simulation tool that is used to model ultrasonic wave interaction with in-plane fiber waviness (also known as marcelling). Wavefield data processing methods are applied to the simulation data to explore possible routes for quantitative defect characterization.

Additive Manufacturing (AM) Activities and Non-Destructive Evaluation (NDE) at GSFC

Science.gov (United States)

Jones, Justin S.

2017-01-01

NASA personnel will be meeting with a delegation from the Japan Aerospace Exploration Agency (JAXA) Office of Safety and Mission Assurance (OSMA) at Langley Research Center on 2217 through 3217. The purpose of the meeting is a technical interchange between NASA and JAXA to discuss Non-Destructive Evaluation (NDE) of Additive Manufacturing (AM) parts and the HALT process (relates to accelerated life testing). The visitors will be a small group of Japanese citizens. Goddard Space Flight Center (GSFC) has been asked to participate in the meeting, either in person or via teleconference. This presentation covers NDE efforts at GSFC and provides a cursory overview of AM and lab capabilities.

Review of Micro/Nano Nondestructive Evaluation Technique (II): Measurement of Acoustic Properties

International Nuclear Information System (INIS)

Kim, Chung Seok; Park, Ik Keun

2012-01-01

The present paper reviews the micro and nano nondestructive evaluation(NDE) technique that is possible to investigate the surface and measure the acoustic properties. The technical theory, features and applications of the ultrasonic atomic force microscopy(UAFM) and scanning acoustic microscopy(SAM) are illustrated. Especially, these technologies are possible to evaluate the mechanical properties in micro/nano structure and surface through the measurement of acoustic properties in addition to the observation of surface and subsurface. Consequently, it is thought that technique developments and applications of these micro/nano NDE in advanced industrial parts together with present nondestructive industry are widely possible hereafter.

NASA OSMA NDE Program Additive Manufacturing Foundational Effort

Science.gov (United States)

Waller, Jess; Walker, James; Burke, Eric; Wells, Douglas; Nichols, Charles

2016-01-01

NASA is providing key leadership in an international effort linking NASA and non-NASA resources to speed adoption of additive manufacturing (AM) to meet NASA's mission goals. Participants include industry, NASA's space partners, other government agencies, standards organizations and academia. Nondestructive Evaluation (NDE) is identified as a universal need for all aspects of additive manufacturing.

NDE of Damage in Aircraft Flight Control Surfaces

International Nuclear Information System (INIS)

Hsu, David K.; Barnard, Daniel J.; Dayal, Vinay

2007-01-01

Flight control surfaces on an aircraft, such as ailerons, flaps, spoilers and rudders, are typically adhesively bonded composite or aluminum honeycomb sandwich structures. These components can suffer from damage caused by hail stone, runway debris, or dropped tools during maintenance. On composites, low velocity impact damages can escape visual inspection, whereas on aluminum honeycomb sandwich, budding failure of the honeycomb core may or may not be accompanied by a disbond. This paper reports a study of the damage morphology in such structures and the NDE methods for detecting and characterizing them. Impact damages or overload failures in composite sandwiches with Nomex or fiberglass core tend to be a fracture or crinkle or the honeycomb cell wall located a distance below the facesheet-to-core bondline. The damage in aluminum honeycomb is usually a buckling failure, propagating from the top skin downward. The NDE methods used in this work for mapping out these damages were: air-coupled ultrasonic scan, and imaging by computer aided tap tester. Representative results obtained from the field will be shown

Printed Ultra-High Temperature NDE Sensors for Complex Structures, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — This Phase I SBIR proposal will address the use of innovative additive manufacturing technologies applicable to Non-Destructive Evaluation (NDE) and Structural...

Application of Automated NDE Data Evaluation to Missile and Aircraft Systems

National Research Council Canada - National Science Library

Hildreth, Joseph

1996-01-01

... from the inspection of solid rocket motors during fabrication. The computerized system, called the Automated NDE Data Evaluation System or ANDES, was developed under contract to Martin Marietta...

Novel Ultra-Miniature Flexible Videoscope for On-Orbit NDE, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Conventional videoscopes for NDE suffer many shortcomings, including large diameter, limited flexibility, inadequate image quality, high cost and lack of 3D imaging...

NDE and fracture mechanics evaluation of bottom-head weld indications in a BWR reactor pressure vessel

Energy Technology Data Exchange (ETDEWEB)

Brickstad, B [Swedish Plant Inspectorate, Stockholm (Sweden)

1988-12-31

This document deals with the Non Destructive Examination (NDE) and the fracture mechanics evaluation of bottom head welds in a BWR. The NDE equipment is presented, together with the geometry of evaluated flaw regions. After the fracture mechanics evaluation, it appeared that the plant results fulfilled the usual conditions, and the plant was allowed to operate one more year. (TEC).

Quantitative NDE of Composite Structures at NASA

Science.gov (United States)

Cramer, K. Elliott; Leckey, Cara A. C.; Howell, Patricia A.; Johnston, Patrick H.; Burke, Eric R.; Zalameda, Joseph N.; Winfree, William P.; Seebo, Jeffery P.

2015-01-01

The use of composite materials continues to increase in the aerospace community due to the potential benefits of reduced weight, increased strength, and manufacturability. Ongoing work at NASA involves the use of the large-scale composite structures for spacecraft (payload shrouds, cryotanks, crew modules, etc). NASA is also working to enable the use and certification of composites in aircraft structures through the Advanced Composites Project (ACP). The rapid, in situ characterization of a wide range of the composite materials and structures has become a critical concern for the industry. In many applications it is necessary to monitor changes in these materials over a long time. The quantitative characterization of composite defects such as fiber waviness, reduced bond strength, delamination damage, and microcracking are of particular interest. The research approaches of NASA's Nondestructive Evaluation Sciences Branch include investigation of conventional, guided wave, and phase sensitive ultrasonic methods, infrared thermography and x-ray computed tomography techniques. The use of simulation tools for optimizing and developing these methods is also an active area of research. This paper will focus on current research activities related to large area NDE for rapidly characterizing aerospace composites.

¿Dónde vamos con los Entornos Personales de Aprendizaje?

OpenAIRE

Attwell, Graham

2013-01-01

Para citar: Attwel, G. (2013). ¿Dónde vamos con los Entornos Personales de Aprendizaje? En L. Castañeda y J. Adell (Eds.), Entornos Personales de Aprendizaje: Claves para el ecosistema educativo en red (pp. 189-192). Alcoy: Marfil.

Cold spray NDE for porosity and other process anomalies

Science.gov (United States)

Glass, S. W.; Larche, M. R.; Prowant, M. S.; Suter, J. D.; Lareau, J. P.; Jiang, X.; Ross, K. A.

2018-04-01

This paper describes a technology review of nondestructive evaluation (NDE) methods that can be applied to cold spray coatings. Cold spray is a process for depositing metal powder at high velocity so that it bonds to the substrate metal without significant heating that would be likely to cause additional residual tensile stresses. Coatings in the range from millimeters to centimeters are possible at relatively high deposition rates. Cold spray coatings that may be used for hydroelectric components that are subject to erosion, corrosion, wear, and cavitation damage are of interest. The topic of cold spray NDE is treated generally, however, but may be considered applicable to virtually any cold spray application except where there are constraints of the hydroelectric component application that bear special consideration. Optical profilometry, eddy current, ultrasound, and hardness tests are shown for one set of good, fair, and poor nickel-chrome (NiCr) on 304 stainless steel (304SS) cold spray samples to demonstrate inspection possibilities. The primary indicator of cold spray quality is the cold spray porosity that is most directly measured with witness-sample destructive examinations (DE)—mostly photo-micrographs. These DE-generated porosity values are correlated with optical profilometry, eddy current, ultrasound, and hardness test NDE methods to infer the porosity and other information of interest. These parameters of interest primarily include: • Porosity primarily caused by improper process conditions (temperature, gas velocity, spray standoff, spray angle, powder size, condition, surface cleanliness, surface oxide, etc.) • Presence/absence of the cold spray coating including possible over-sprayed voids • Coating thicknessOptical profilometry measurements of surface roughness trended with porosity plus, if compared with a reference measurement or reference drawing, would provide information on the coating thickness. Ultrasound could provide similar

Mobile HTS-SQUID NDE system with robot arm and active shielding using fluxgate

Energy Technology Data Exchange (ETDEWEB)

Hatsukade, Y. [Department of Ecological Engineering, Toyohashi University of Technology, 1-1 Hibarigaoka, Tempaku-cho, Toyohashi, Aichi 441-8580 (Japan)], E-mail: hatukade@eco.tut.ac.jp; Yotsugi, K.; Tanaka, S. [Department of Ecological Engineering, Toyohashi University of Technology, 1-1 Hibarigaoka, Tempaku-cho, Toyohashi, Aichi 441-8580 (Japan)

2008-09-15

A robot-arm-based mobile HTS-SQUID NDE system was developed for inspection of advanced structures such as hydrogen fuel cell tanks. In order to realize stable operation of HTS-SQUID exposed in Earth's field and robot arm's noise without flux trapping, flux jumping and unlocking during motion, a new active magnetic shielding (AMS) technique using fluxgate was introduced. The high sensitive fluxgate, which could measure magnetic field of up to several 10 {mu}T, was mounted near an HTS-SQUID gradiometer on the robot arm to measure the ambient noise and feed back its output to a compensation coil, which surrounded both SQUID and fluxgate to cancel the ambient noise around them. The AMS technique successfully enabled the HTS-SQUID gradiometer to be moved at 10 mm/s by the robot arm in unshielded environment without flux trapping, jumping and unlocking. Detection of hidden slots in multi-layer composite-metal structures imitating the fuel cell tank was demonstrated.

Position-controlled data acquisition embedded system for magnetic NDE of bridge stay cables.

Science.gov (United States)

Maldonado-Lopez, Rocio; Christen, Rouven

2011-01-01

This work presents a custom-tailored sensing and data acquisition embedded system, designed to be integrated in a new magnetic NDE inspection device under development at Empa, a device intended for routine testing of large diameter bridge stay cables. The data acquisition (DAQ) system fulfills the speed and resolution requirements of the application and is able to continuously capture and store up to 2 GB of data at a sampling rate of 27 kS/s, with 12-bit resolution. This paper describes the DAQ system in detail, including both hardware and software implementation, as well as the key design challenges and the techniques employed to meet the specifications. Experimental results showing the performance of the system are also presented.

Computer Aided Feature Extraction, Classification and Acceptance Processing of Digital NDE Data

National Research Council Canada - National Science Library

Hildreth, Joseph

1996-01-01

... from the inspection of solid rocket motors during fabrication. The computerized system, called the Automated NDE Data Evaluation System or ANDES, was developed under contract to Martin Marietta, now Lockheed Martin...

Primary water stress corrosion cracks in nickel alloy dissimilar metal welds: Detection and sizing using established and emerging nondestructive examination techniques

International Nuclear Information System (INIS)

Braatz, B.G.; Doctor, S.R.; Cumblidge, S.E.; Prokofiev, I.G.

2012-01-01

The U.S. Nuclear Regulatory Commission has established the Program to Assess the Reliability of Emerging Nondestructive Techniques (PARENT) as a follow-on to the international cooperative Program for the Inspection of Nickel Alloy Components (PINC). The goal of PINC was to evaluate the capabilities of various nondestructive evaluation (NDE) techniques to detect and characterize surface-breaking primary water stress corrosion cracks in dissimilar-metal welds (DMW) in bottom-mounted instrumentation (BMI) penetrations and small-bore (∼400-mm diameter) piping components. A series of international blind round-robin tests were conducted by commercial and university inspection teams. Results from these tests showed that a combination of conventional and phased-array ultrasound techniques provided the highest performance for flaw detection and depth sizing in dissimilar metal piping welds. The effective detection of flaws in BMIs by eddy current and ultrasound shows that it may be possible to reliably inspect these components in the field. The goal of PARENT is to continue the work begun in PINC and apply the lessons learned to a series of open and blind international round-robin tests that will be conducted on a new set of piping components including large-bore (∼900-mm diameter) DMWs, small-bore DMWs, and BMIs. Open round-robin testing will engage universities and industry worldwide to investigate the reliability of emerging NDE techniques to detect and accurately size flaws having a wide range of lengths, depths, orientations, and locations. Blind round-robin testing will invite testing organizations worldwide, whose inspectors and procedures are certified by the standards for the nuclear industry in their respective countries, to investigate the ability of established NDE techniques to detect and size flaws whose characteristics range from easy to very difficult to detect and size. This paper presents highlights of PINC and reports on the plans and progress for

Primary Water Stress Corrosion Cracks in Nickel Alloy Dissimilar Metal Welds: Detection and Sizing Using Established and Emerging Nondestructive Examination Techniques

Energy Technology Data Exchange (ETDEWEB)

Braatz, Brett G.; Cumblidge, Stephen E.; Doctor, Steven R.; Prokofiev, Iouri

2012-12-31

The U.S. Nuclear Regulatory Commission has established the Program to Assess the Reliability of Emerging Nondestructive Techniques (PARENT) as a follow-on to the international cooperative Program for the Inspection of Nickel Alloy Components (PINC). The goal of PINC was to evaluate the capabilities of various nondestructive evaluation (NDE) techniques to detect and characterize surface-breaking primary water stress corrosion cracks in dissimilar-metal welds (DMW) in bottom-mounted instrumentation (BMI) penetrations and small-bore (≈400-mm diameter) piping components. A series of international blind round-robin tests were conducted by commercial and university inspection teams. Results from these tests showed that a combination of conventional and phased-array ultrasound techniques provided the highest performance for flaw detection and depth sizing in dissimilar metal piping welds. The effective detection of flaws in BMIs by eddy current and ultrasound shows that it may be possible to reliably inspect these components in the field. The goal of PARENT is to continue the work begun in PINC and apply the lessons learned to a series of open and blind international round-robin tests that will be conducted on a new set of piping components including large-bore (≈900-mm diameter) DMWs, small-bore DMWs, and BMIs. Open round-robin testing will engage universities and industry worldwide to investigate the reliability of emerging NDE techniques to detect and accurately size flaws having a wide range of lengths, depths, orientations, and locations. Blind round-robin testing will invite testing organizations worldwide, whose inspectors and procedures are certified by the standards for the nuclear industry in their respective countries, to investigate the ability of established NDE techniques to detect and size flaws whose characteristics range from easy to very difficult to detect and size. This paper presents highlights of PINC and reports on the plans and progress for

An interaction between NDE1 and high birth weight increases schizophrenia susceptibility.

Science.gov (United States)

Wegelius, Asko; Pankakoski, Maiju; Tomppo, Liisa; Lehto, Ulriika; Lönnqvist, Jouko; Suvisaari, Jaana; Paunio, Tiina; Hennah, William

2015-12-15

Pre- and perinatal environmental factors have been shown to increase schizophrenia risk particularly when combined with genetic liability. The investigation of specific gene environment interactions in the etiology of psychiatric disorders has gained momentum. We used multivariate GEE regression modeling to investigate the interaction between genes of the DISC1 pathway and birth weight, in relation to schizophrenia susceptibility in a Finnish schizophrenia family cohort. The study sample consisted of 457 subjects with both genotype and birth weight information. Gender and place of birth were adjusted for in the models. We found a significant interaction between birth weight and two NDE1 markers in relation to increased schizophrenia risk: a four SNP haplotype spanning NDE1 (b=1.26, SE=0.5, p=0.012) and one of its constituent SNPs rs4781678 (b=1.33, SE=0.51, p=0.010). Specifically, high birth weight (>4000g) was associated with increased schizophrenia risk among subjects homozygous for the previously identified risk alleles. The study was based on a family study sample with high genetic loading for schizophrenia and thus our findings cannot directly be generalized as representing the general population. Our results suggest that the functions mediated by NDE1 during the early stages of neurodevelopment are susceptible to the additional disruptive effects of pre- and perinatal environmental factors associated with high birth weight, augmenting schizophrenia susceptibility. Copyright © 2015 The Authors. Published by Elsevier Ireland Ltd.. All rights reserved.

Development of non-destructive examination techniques for CFC-metal joints in annular geometry and their application to the manufacturing of plasma-facing components

International Nuclear Information System (INIS)

Di Pietro, E.; Visca, E.; Orsini, A.; Sacchetti, M.; Borruto, T.M.R.; Varone, P.; Vesprini, R.

1995-01-01

The design of plasma-facing components for ITER, as for any of the envisaged next-step machines, relies heavily on the use of brazed junctions to couple armour materials to the heat sink and cooling tubes. Moreover, the typical number of brazed components and the envisaged effects of local overheating due to failure in a single brazed junction stress the importance of having a set of NDE techniques developed that can ensure the flawless quality of the joint. The qualification and application of two NDE techniques (ultrasonic and thermographic analysis) for inspection of CFC-to-metal joints is described with particular regard to the annular geometry typical of macroblock/monoblock solutions for divertor high-heat-flux components. The results of the eddy current inspection are not reported. The development has been focused specifically on the joint between carbon-fiber composite and TZM molybdenum alloy; techniques for the production of reference defect samples have been devised and a set of reference defect samples produced. The comparative results of the NDE inspections are reported and discussed, also on the basis of the destructive examination of the samples. The nature and size of relevant and detectable defects are discussed together with hints for a possible NDE strategy for divertor high-heat-flux components

Development of composite calibration standard for quantitative NDE by ultrasound and thermography

Science.gov (United States)

Dayal, Vinay; Benedict, Zach G.; Bhatnagar, Nishtha; Harper, Adam G.

2018-04-01

Inspection of aircraft components for damage utilizing ultrasonic Non-Destructive Evaluation (NDE) is a time intensive endeavor. Additional time spent during aircraft inspections translates to added cost to the company performing them, and as such, reducing this expenditure is of great importance. There is also great variance in the calibration samples from one entity to another due to a lack of a common calibration set. By characterizing damage types, we can condense the required calibration sets and reduce the time required to perform calibration while also providing procedures for the fabrication of these standard sets. We present here our effort to fabricate composite samples with known defects and quantify the size and location of defects, such as delaminations, and impact damage. Ultrasonic and Thermographic images are digitally enhanced to accurately measure the damage size. Ultrasonic NDE is compared with thermography.

Investigation of a Novel NDE Method for Monitoring Thermomechanical Damage and Microstructure Evolution in Ferritic-Martensitic Steels for Generation IV Nuclear Energy Systems

Energy Technology Data Exchange (ETDEWEB)

Nagy, Peter

2013-09-30

The main goal of the proposed project is the development of validated nondestructive evaluation (NDE) techniques for in situ monitoring of ferritic-martensitic steels like Grade 91 9Cr-1Mo, which are candidate materials for Generation IV nuclear energy structural components operating at temperatures up to ~650{degree}C and for steam-generator tubing for sodium-cooled fast reactors. Full assessment of thermomechanical damage requires a clear separation between thermally activated microstructural evolution and creep damage caused by simultaneous mechanical stress. Creep damage can be classified as "negligible" creep without significant plastic strain and "ordinary" creep of the primary, secondary, and tertiary kind that is accompanied by significant plastic deformation and/or cavity nucleation and growth. Under negligible creep conditions of interest in this project, minimal or no plastic strain occurs, and the accumulation of creep damage does not significantly reduce the fatigue life of a structural component so that low-temperature design rules, such as the ASME Section III, Subsection NB, can be applied with confidence. The proposed research project will utilize a multifaceted approach in which the feasibility of electrical conductivity and thermo-electric monitoring methods is researched and coupled with detailed post-thermal/creep exposure characterization of microstructural changes and damage processes using state-of-the-art electron microscopy techniques, with the aim of establishing the most effective nondestructive materials evaluation technique for particular degradation modes in high-temperature alloys that are candidates for use in the Next Generation Nuclear Plant (NGNP) as well as providing the necessary mechanism-based underpinnings for relating the two. Only techniques suitable for practical application in situ will be considered. As the project evolves and results accumulate, we will also study the use of this technique for monitoring other GEN IV

Entering the Era of "Super" NDE Instruments, Followed by Progressive Miniaturization, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — An ideal NDE data acquisition and analysis tool would be a versatile and precise device capable of providing support for a large number of inspections using numerous...

The NDE1 genomic locus can affect treatment of psychiatric illness through gene expression changes related to microRNA-484.

Science.gov (United States)

Bradshaw, Nicholas J; Ukkola-Vuoti, Liisa; Pankakoski, Maiju; Zheutlin, Amanda B; Ortega-Alonso, Alfredo; Torniainen-Holm, Minna; Sinha, Vishal; Therman, Sebastian; Paunio, Tiina; Suvisaari, Jaana; Lönnqvist, Jouko; Cannon, Tyrone D; Haukka, Jari; Hennah, William

2017-11-01

Genetic studies of familial schizophrenia in Finland have observed significant associations with a group of biologically related genes, DISC1 , NDE1 , NDEL1 , PDE4B and PDE4D , the 'DISC1 network'. Here, we use gene expression and psychoactive medication use data to study their biological consequences and potential treatment implications. Gene expression levels were determined in 64 individuals from 18 families, while prescription medication information has been collected over a 10-year period for 931 affected individuals. We demonstrate that the NDE1 SNP rs2242549 associates with significant changes in gene expression for 2908 probes (2542 genes), of which 794 probes (719 genes) were replicable. A significant number of the genes altered were predicted targets of microRNA-484 ( p = 3.0 × 10 -8 ), located on a non-coding exon of NDE1 Variants within the NDE1 locus also displayed significant genotype by gender interaction to early cessation of psychoactive medications metabolized by CYP2C19. Furthermore, we demonstrate that miR-484 can affect the expression of CYP2C19 in a cell culture system. Thus, variation at the NDE1 locus may alter risk of mental illness, in part through modification of miR-484, and such modification alters treatment response to specific psychoactive medications, leading to the potential for use of this locus in targeting treatment. © 2017 The Authors.

NDE methods for determining the materials properties of silicon carbide plates

Science.gov (United States)

Kenderian, Shant; Kim, Yong; Johnson, Eric; Palusinski, Iwona A.

2009-08-01

Two types of SiC plates, differing in their manufacturing processes, were interrogated using a variety of NDE techniques. The task of evaluating the materials properties of these plates was a challenge due to their non-uniform thickness. Ultrasound was used to estimate the Young's Modulus and calculate the thickness profile and Poisson's Ratio of the plates. The Young's Modulus profile plots were consistent with the thickness profile plots, indicating that the technique was highly influenced by the non-uniform thickness of the plates. The Poisson's Ratio is calculated from the longitudinal and shear wave velocities. Because the thickness is cancelled out, the result is dependent only on the time of flight of the two wave modes, which can be measured accurately. X-Ray was used to determine if any density variations were present in the plates. None were detected suggesting that the varying time of flight of the acoustic wave is attributed only to variations in the elastic constants and thickness profiles of the plates. Eddy Current was used to plot the conductivity profile. Surprisingly, the conductivity profile of one type of plates varied over a wide range rarely seen in other materials. The other type revealed a uniform conductivity profile.

Limitations of the Neurological Evolutional Exam (ENE) as a motor assessment for first graders.

Science.gov (United States)

Caçola, Priscila M; Bobbio, Tatiana G; Arias, Amabile V; Gonçalves, Vanda G; Gabbard, Carl

2010-01-01

many clinicians and researchers in Brazil consider the Neurological Developmental Exam (NDE), a valid and reliable assessment for Brazilian school-aged children. However, since its inception, several tests have emerged that, according to some researchers, provide more in-depth evaluation of motor ability and go beyond the detection of general motor status (soft neurological signs). to highlight the limitations of the NDE as a motor skill assessment for first graders. thirty-five children were compared on seven selected items of the NDE, seven of the Bruininks-Oseretsky Test (BOT), and seven of the Visual-Motor Integration test (VMI). Participants received a "pass" or "fail" score for each item, as prescribed by the respective test manual. chi-square and ANOVA results indicated that the vast majority of children (74%) passed the NDE items, whereas values for the other tests were 29% (BOT) and 20% (VMI). Analysis of specific categories (e.g. visual, fine, and gross motor coordination) revealed a similar outcome. our data suggest that while the NDE may be a valid and reliable test for the detection of general motor status, its use as a diagnostic/remedial tool for identifying motor ability is questionable. One of our recommendations is the consideration of a revised NDE in light of the current needs of clinicians and researchers.

The use of fracture mechanics for the evaluation of NDE flaw acceptance standards

Energy Technology Data Exchange (ETDEWEB)

Alicino, A; Capurro, E; Ansaldo, Sp; Corvi, A [Ansaldo SpA, Genoa (Italy)

1988-12-31

This document deals with the use of fracture mechanics criteria to evaluate the Non Destructive Examination (NDE) flaw acceptance standards. The communication discusses the general schemes and the guidelines of the activity carried out. (TEC).

Application of X-ray NDE in treating with chemical weapons abandoned by Japan

International Nuclear Information System (INIS)

Wang Bairong; Zhang Guohua; Jiang Yishan

2006-01-01

According as need of treating with CW abandoned by Japan, this paper designs a X-ray NDE system for chemical weapons. It consist of X-ray shooting unit, control and identification unit and some assistant equipment. (authors)

Untersuchungen zur Anwendbarkeit eines integrierten Nachweissystems für Penicillin-Rückstände in Kuhmilch und Ziegenmilch

OpenAIRE

Kress, Claudia

2010-01-01

In der vorliegenden Arbeit wurde die Anwendbarkeit eines integrierten Nachweissystems für Penicillin-Rückstände in Kuhmilch und Ziegenmilch überprüft. Der zweite Schwerpunkt dieser Arbeit lag auf der Hemmstoffbelastung von Ziegenmilch, d.h. es sollte ein Überblick über die Belastung der in Hessen produzierten Ziegenmilch mit Penicillin-Rückständen gewonnen werden. Die „Kernmethode“ des integrierten Nachweissystems für Penicillin-Rückstände in Kuhmilch und Ziegenmilch ist ein...

A circular aperture array for ultrasonic tomography and quantitative NDE

Energy Technology Data Exchange (ETDEWEB)

Nielsen, S A

1998-08-01

The main topics of this thesis are ultrasonic tomography and ultrasonic determination of elastic stiffness constants. Both issues are based on a synthetic array with transducer elements distributed uniformly along a circular aperture, i.e., a circular aperture array. The issues are treated both theoretically and experimentally by broadband pulse techniques. Ultrasonic tomography, UCT, from a circular aperture is a relatively new imaging technique in Non-destructive Evaluation (NDE) to acquire cross sectional images in bulk materials. A filtered back-projection algorithm is used to reconstruct images in four different experiments and results of attenuation, velocity and reflection tomograms in Plexiglas of AlSi-alloy cylinders are presented. Two kinds of ultrasonic tomography are introduced: bistatic and monostatic imaging. Both techniques are verified experimentally by Plexiglas cylinders. Different reconstruction artifacts are discussed and theoretical resolution constraints are discussed for various configurations of the circular aperture array. The monostatic technique is used in volumetric imaging. In the experimental verification artificial and real discontinuities in a cylindrical AlSi-alloy are compared with similar discontinuities in a Plexiglas specimen. Finally, some limitations to UCT are discussed. The circular aperture array is used to determine five independent elastic stiffness constants of a unidirectional glass/PET (Poly Ethylene Teraphtalate) laminate. Energy flux propagation and attenuation of ultrasonic waves are considered and velocity surfaces are calculated for different planes of interest. Relations between elastic stiffness constants and engineering constants (i.e., Young`s moduli, shear moduli and Poisson`s ratios) are discussed for an orthotropic composite. Six micromechanical theories are reviewed, and expressions predicting the elastic engineering constants are evaluated. The micromechanical predicted elastic stiffness constants for the

Evaluation of Advanced Signal Processing Techniques to Improve Detection and Identification of Embedded Defects

Energy Technology Data Exchange (ETDEWEB)

Clayton, Dwight A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Santos-Villalobos, Hector J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Baba, Justin S. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2016-09-01

By the end of 1996, 109 Nuclear Power Plants were operating in the United States, producing 22% of the Nation’s electricity [1]. At present, more than two thirds of these power plants are more than 40 years old. The purpose of the U.S. Department of Energy Office of Nuclear Energy’s Light Water Reactor Sustainability (LWRS) Program is to develop technologies and other solutions that can improve the reliability, sustain the safety, and extend the operating lifetimes of nuclear power plants (NPPs) beyond 60 years [2]. The most important safety structures in an NPP are constructed of concrete. The structures generally do not allow for destructive evaluation and access is limited to one side of the concrete element. Therefore, there is a need for techniques and technologies that can assess the internal health of complex, reinforced concrete structures nondestructively. Previously, we documented the challenges associated with Non-Destructive Evaluation (NDE) of thick, reinforced concrete sections and prioritized conceptual designs of specimens that could be fabricated to represent NPP concrete structures [3]. Consequently, a 7 feet tall, by 7 feet wide, by 3 feet and 4-inch-thick concrete specimen was constructed with 2.257-inch-and 1-inch-diameter rebar every 6 to 12 inches. In addition, defects were embedded the specimen to assess the performance of existing and future NDE techniques. The defects were designed to give a mix of realistic and controlled defects for assessment of the necessary measures needed to overcome the challenges with more heavily reinforced concrete structures. Information on the embedded defects is documented in [4]. We also documented the superiority of Frequency Banded Decomposition (FBD) Synthetic Aperture Focusing Technique (SAFT) over conventional SAFT when probing defects under deep concrete cover. Improvements include seeing an intensity corresponding to a defect that is either not visible at all in regular, full frequency content SAFT

Nondestructive Examination of Possible PWSCC in Control Rod Drive Mechanism Housings

International Nuclear Information System (INIS)

Doctor, Steven R.; Cumblidge, Stephen E.; Schuster, George J.; Harris, Rob V.; Crawford, Susan L.

2007-01-01

Studies being conducted at the Pacific Northwest National Laboratory (PNNL) in Richland, Washington are focused on assessing the effectiveness of nondestructive examination (NDE) techniques for inspecting control rod drive mechanism (CRDM) nozzles and J-groove weldments. The primary objective of this work is to provide information to the United States Nuclear Regulatory Commission (US NRC) on the effectiveness of NDE methods as related to the in-service inspection of CRDM nozzles and J-groove weldments, and to enhance the knowledge base of primary water stress corrosion cracking (PWSCC) through destructive characterization of the CRDM assemblies. In describing two CRDM assemblies removed from service, decontaminated, and then used in a series of NDE measurements, this paper will address the following questions: (1) What did each technique detect? (2) What did each technique miss? and (3) How accurately did each technique characterize the detected flaws? Two CRDM assemblies including the CRDM nozzle, the J-groove weld, buttering, and a portion of the ferritic head material were selected for this study. One contained suspected PWSCC, based on in-service inspection data and through-wall leakage; the other contained evidence suggesting through-wall leakage, but this was unconfirmed. The selected NDE measurements follow standard industry techniques for conducting in-service inspections of CRDM nozzles and the crown of the J-groove welds and buttering. In addition, laboratory based NDE methods were employed to conduct inspections of the CRDM assemblies, with particular emphasis on inspecting the J-groove weld and buttering. This paper will also describe the NDE methods used and discuss the NDE results. Future work will involve using the results from these NDE studies to guide the development of a destructive characterization plan to reveal the crack morphology and a comparison of the degradation found by the destructive evaluation with the recorded NDE responses

A robust approach to optimal matched filter design in ultrasonic non-destructive evaluation (NDE)

Science.gov (United States)

Li, Minghui; Hayward, Gordon

2017-02-01

The matched filter was demonstrated to be a powerful yet efficient technique to enhance defect detection and imaging in ultrasonic non-destructive evaluation (NDE) of coarse grain materials, provided that the filter was properly designed and optimized. In the literature, in order to accurately approximate the defect echoes, the design utilized the real excitation signals, which made it time consuming and less straightforward to implement in practice. In this paper, we present a more robust and flexible approach to optimal matched filter design using the simulated excitation signals, and the control parameters are chosen and optimized based on the real scenario of array transducer, transmitter-receiver system response, and the test sample, as a result, the filter response is optimized and depends on the material characteristics. Experiments on industrial samples are conducted and the results confirm the great benefits of the method.

The application of X-ray NDE in treating with chemical weapons abandoned by Japan

International Nuclear Information System (INIS)

Wang Bairong; Jiang Yishan; Zhang Guohua

2003-01-01

According as need of treating with CW abandoned by Japan, this paper designs a X-ray NDE system for chemical weapons, it consist of X-ray shooting unit, control and identification unit and some assistant equipments

Shearography: An alternative method of NDE for analysis of corrosion in petroleum pipeline

International Nuclear Information System (INIS)

Mohd Yusnisyam Yusof; Wan Saffiey Wan Abdullah

2009-01-01

This paper discusses the use of shearography as an alternative method of NDE for analysis of corrosion in petroleum pipeline. Shearography reveals direct information about defect induced stress which utilized the laser wave front pattern on the inspected object. In this study, the laser shearography technique was used to measure the derivative displacement of 7 mm thickness carbon steel pipe wall surface with simulated corrosion area at internal wall. The wave front pattern of internal wall corrosion in petroleum pipeline will be constructed to 3D image profiles in order to measure the severity and magnitude of material deformation. The process may involve of optical phase stepping procedure and the image processing algorithm for wrapped and unwrapped phase image at the deformation area. The unwrapped phase image can be meshed plot which finally lead to 3D image profiles. The phase stepping procedure in this analysis was selected by utilizing four phase stepping procedure using piezoelectric transducer (PZT) attached with optical mirror. (author)

Siserände suundumused 20. sajandil = Trends of internal migration during the 20th century and at the beginning of the 21st century / Alis Tammur

Index Scriptorium Estoniae

Tammur, Alis

2008-01-01

Siserände suundadest Eestis alates 1920ndatest aastatest kuni 2007. aastani. Kaart: Linnadesse tulnud endise alalise elukoha järgi, 1922-1934. Graafik: Siserände vanusjaotus. Tabel: Linnade ja maa-asulate vahelised rändesuunad 2000-2007

AMERİKA BİRLEŞİK DEVLETLERİ’NDE DEVLETİN YENİDEN YAPILANDIRILMASINA YÖNELİK UYGULAMALAR (Clinton-Al Gore Girişimi: 1993-2001)

OpenAIRE

Aktan, Coşkun Can

2018-01-01

ABD’nde devletin yeniden yapılandırılması çalışmaları William Clinton’un başkanlığı döneminde Başkan Yardımcılığı görevini yürüten Al Gore öncülüğünde yürütülmüştür. ABD’nde bu amaçla National Performance Review adlı bir de yeniden yapılandırma laboratuvarı kurulmuştur. Bu kurum daha sonra National Partnership for Reinventing Government adını almıştır. Bu çalışmada 1993-2001 yılları arasında ABD’nde devletin yeniden yapılandırılmasına yönelik uygulamalar incelenmektedir....

Light Water Reactor Sustainability (LWRS) Program – Non-Destructive Evaluation (NDE) R&D Roadmap for Determining Remaining Useful Life of Aging Cables in Nuclear Power Plants

Energy Technology Data Exchange (ETDEWEB)

Simmons, K.L.; Ramuhali, P.; Brenchley, D.L.; Coble, J.B.; Hashemian, H.M.; Konnick, R.; Ray, S.

2012-09-01

Executive Summary [partial] The purpose of the non-destructive evaluation (NDE) R&D Roadmap for Cables is to support the Materials Aging and Degradation (MAaD) R&D pathway. A workshop was held to gather subject matter experts to develop the NDE R&D Roadmap for Cables. The focus of the workshop was to identify the technical gaps in detecting aging cables and predicting their remaining life expectancy. The workshop was held in Knoxville, Tennessee, on July 30, 2012, at Analysis and Measurement Services Corporation (AMS) headquarters. The workshop was attended by 30 experts in materials, electrical engineering, and NDE instrumentation development from the U.S. Nuclear Regulatory Commission (NRC), U.S. Department of Energy (DOE) National Laboratories (Oak Ridge National Laboratory, Pacific Northwest National Laboratory, Argonne National Laboratory, and Idaho National Engineering Laboratory), universities, commercial NDE service vendors and cable manufacturers, and the Electric Power Research Institute (EPRI).

Graphics processing unit based computation for NDE applications

Science.gov (United States)

Nahas, C. A.; Rajagopal, Prabhu; Balasubramaniam, Krishnan; Krishnamurthy, C. V.

2012-05-01

Advances in parallel processing in recent years are helping to improve the cost of numerical simulation. Breakthroughs in Graphical Processing Unit (GPU) based computation now offer the prospect of further drastic improvements. The introduction of 'compute unified device architecture' (CUDA) by NVIDIA (the global technology company based in Santa Clara, California, USA) has made programming GPUs for general purpose computing accessible to the average programmer. Here we use CUDA to develop parallel finite difference schemes as applicable to two problems of interest to NDE community, namely heat diffusion and elastic wave propagation. The implementations are for two-dimensions. Performance improvement of the GPU implementation against serial CPU implementation is then discussed.

NOAA JPSS Visible Infrared Imaging Radiometer Suite (VIIRS) Vegetation Health and Drought Products (VHDP) from NDE

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The VIIRS Vegetation Health and Drought Products (VHDP) from NDE algorithm provides weekly estimates of the Vegetation Condition Index (VCI), Temperature Condition...

Alternative Assessment Techniques.

Science.gov (United States)

Lowenthal, Barbara

1988-01-01

Maintaining the precision necessary for administering norm referenced tests can be a problem for the special education teacher who is trained to assist the student. Criterion-referenced tests, observations, and interviews are presented as effective alternative assessment techniques. (JDD)

Explorer-II: Wireless Self-Powered Visual and NDE Robotic Inspection System for Live Gas Distribution Mains

Energy Technology Data Exchange (ETDEWEB)

Carnegie Mellon University

2008-09-30

-pressure environments, and is safely deployable using proper evacuating/purging techniques for operation in the potentially explosive natural gas environment. The test-setting and environment for safety-certification of the X-II robot platform and the launch and recovery procedures, is shown. Field-trials were successfully carried out in a live steel pipeline in Northwestern Pennsylvania. The robot was launched and recovered multiple times, travelling thousands of feet and communicating in real time with video and command-and-control (C&C) data under remote operator control from a laptop, with NDE sensor-data streaming to a second computer for storage, display and post-processing. Representative images of the activities and systems used in the week-long field-trial are shown. CMU also evaluated the ability of the X-II design to be able to integrate an MFL sensor, by adding additional drive-/battery-/steering- and support-modules to extend the X-II train.

NOAA JPSS Visible Infrared Imaging Radiometer Suite (VIIRS) Smoothed Normalized Difference Vegetation Index (NDVI) from NDE

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Visible Infrared Imaging Radiometer Suite (VIIRS) Smoothed Normalized Difference Vegetation Index (NDVI) from NDE is a weekly product derived from the VIIRS...

Development priorities for non-destructive examination of concrete structures in nuclear plant

International Nuclear Information System (INIS)

1998-01-01

The objective of this report is to provide a basis for assessing development priorities for NDE of safety related concrete structures in nuclear plants, taking account of both the benefit and the cost of potential developments in NDE techniques. An OECD/NEA Workshop which considered the requirements for NDE of safety related concrete structures was held in the UK on 12 November 97. NDE techniques have the potential to satisfy at least some of the needs of the nuclear industry. NDE techniques have been used successfully on a variety of reinforced and post-tensioned concrete structures, notably highway and reservoir structures. However, there is limited experience of their use to evaluate typical nuclear safety related structures having thick sections, steel liners or access to one side only. There is a general lack of confidence in the techniques because there is very little independent advice on their applicability, capability, accuracy and reliability. The information obtained by techniques such as RADAR, ultrasonics, stress wave and radiography appears qualitative rather than quantitative and there is concern that NDE procedures lack the necessary qualification to permit their use on safety critical structures. There is no authoritative international guidance or standard for NDE of concrete structures. NDE of concrete structures is often based upon equipment developed for other materials and technologies, eg. examination of steel, evaluation of ground conditions. Other industries are developing equipment specifically for civil engineering applications and at the recent OECD workshop a number of relevant national and European programmes were identified. The nuclear industry maintain its awareness of developments and should seek to influence the development of equipment. The quantification of the capabilities of NDE techniques is seen as a priority area for development. The provision of authoritative documentation in the form of reports and Standards is desirable

Peatused teekonnal läände : [luuletused] / James Wright ; tõlk. Jüri Talvet

Index Scriptorium Estoniae

Wright, James

2008-01-01

Sisu: Peatused teekonnal läände ; Kaks kassiahastust ; Kaubamaja kassa juures ; Vastuseks kuuldusele et vanim lõbumaja Wheelingis, Lääne-Virginias, on kinni pandud ; Hiline november põllul ; Sappho järgi mugandatud moraaliluuletus ; Sajandi ood ; Jah, aga. Elu- ja loomeloolisi andmeid autori kohta lk. 535

Bitlis Etnografya Müzesi'nde Bulunan Geleneksel Giysiler

OpenAIRE

Sökmen, Sultan

2016-01-01

Bu çalışmada, Bitlis Etnografya Müzesi'nde sergilenmekte olan geleneksel giysilerin kumaş, renk, süsleme ve teknik özelliklerinin tanıtımı amaçlanmıştır. Bu amaç doğrultusunda ilgili makamlardan yazılı izin alınarak müze vitrinlerinde sergilenmekte olan ve depolarda koruma altına alınan giysilerin fotoğrafları çekilmiş, gerekli ölçümleri yapılarak teknik özellikleri belirlenmiş, hammadde ve süsleme özellikleri incelenmiştir. Müzede bulunan geleneksel giysi örnekleri yeterince zengin olma...

Advanced Inspection and Repair Welding Techniques for SCC Countermeasures

International Nuclear Information System (INIS)

Takagi, T.; Nishimoto, K.; Uchimoto, T.

2012-01-01

Feasibility studies of advanced inspection and repair welding techniques were conducted in the framework of the Nuclear and Industry Safety Agency of Japan (NISA) project on the enhancement of ageing management and maintenance of NPPs. In this paper, features of NDE methods investigated in the projects, main results of research activities and prospect of nickel based alloy weld inspection are discussed. We also make a review for the integrity and reliability evaluation techniques for repair welding of ageing plants which were intensively investigated in view of regulatory criteria, in NISA project. (author)

Suur põgenemine 1944 : eestlaste lahkumine läände ning selle mõjud / Peep Pillak

Index Scriptorium Estoniae

Pillak, Peep, 1957-

2005-01-01

Välis-Eesti uuringute keskuse ja Rootsi Eesti saatkonna korraldatud teaduskonverensist (Tartu, 22. okt. 2004), kus arutluse all oli 1944. a. suur põgenemine läände ja selle mõjud tänasesse päeva

Data combination of infrared thermography images and lock-in thermography images for NDE of plasma facing components

International Nuclear Information System (INIS)

Moysan, J.; Gueudre, C.; Corneloup, G.; Durocher, A.

2006-01-01

A pioneering activity has been developed by CEA and the European industry in the field of actively cooled high heat flux plasma facing components (PFC) from the very beginning of Tore Supra project. These components have been developed in order to enable a large power exhaust capability. The goal of this study is to improve the Non Destructive Evaluation (NDE) of these components. The difficulty encountered is the evaluation of the junction between a carbon and a metallic substrate. This was even more difficult when complex designs have to be implemented. A first NDE solution was based on the so called SATIR test. The method is based on infrared measurements of tile surface temperatures during a thermal transient produced by hot/cold water flowing in the heat sink cooling channel. In order to improve the definition of acceptance rules for the PFCs, a second NDE method based on Lock-in Thermography is developed. In this work we present how we can combine the two resulting images in order to accept or to reject a component. This prospective study allows improving the experimental setup and the definition of acceptance criteria. The experimental study was conducted on trial components for the Wendelstein 7X stellarator. The conclusions will also influence future non destructive projects dedicated to the ITER project. (orig.)

In-Situ NDE Characterization of Kevlar and Carbon Composite Micromechanics for Improved COPV Health Monitoring

Science.gov (United States)

Waller, Jess M.; Saulsberry, Regor L.

2009-01-01

This project is a subtask of a multi-center project to advance the state-of-the-art by developing NDE techniques that are capable of evaluating stress rupture (SR) degradation in Kevlar/epoxy (K/Ep) composite overwrapped pressure vessels (COPVs), and damage progression in carbon/epoxy (C/Ep) COPVs. In this subtask, acoustic emission (AE) data acquired during intermittent load hold tensile testing of K/Ep and C/Ep composite tow materials-of-construction used in COPV fabrication were analyzed to monitor progressive damage during the approach to tensile failure. Insight into the progressive damage of composite tow was gained by monitoring AE event rate, energy, source location, and frequency. Source location based on arrival time data was used to discern between significant AE attributable to microstructural damage and spurious AE attributable to background and grip noise. One of the significant findings was the observation of increasing violation of the Kaiser effect (Felicity ratio < 1.0) with damage accumulation.

Detection of creep damage in a nickel base superalloy using NDE techniques

International Nuclear Information System (INIS)

Carreon, H.; Mora, B.; Barrera, G.

2009-10-01

Due to elevated temperatures, excessive stresses and severed corrosion conditions, turbine engine components are subject to creep processes that limit the components life such as a turbine bucket. The failure mechanism of a turbine bucket is related primarily to creep and corrosion and secondarily to thermal fatigue. As a result, it is desirable to assess the current conditions of such turbine component. This study uses the eddy current nondestructive evaluation technique in an effort to monitor the creep damage in a nickel base super-alloy, turbine bucket after service. The experimental results show an important electrical conductivity variation in eddy current images on the creep damage zone of nickel base super-alloy samples cut from a turbine bucket. Thermoelectric power measurements were also conducted in order to obtain a direct correlation between the presence of material changes due to creep damage and the electrical conductivity measurements. This research work shows an alternative non-destructive method in order to detect creep damage in a nickel base super-alloy turbine bucket. (Author)

Ultrasonic system for NDE of fruits and vegetables

International Nuclear Information System (INIS)

Jhang, Kyung Young; Jung, Gyoo Hong; Kim, Man Soo

1999-01-01

The nondestructive internal quality evaluation of agricultural products has been strongly required from the needs for individual inspection. In recent, ultrasonic wave has been considered as a solution for this problem. This study is to construct the ultrasonic inspection system for fruits and vegetables on the basis of pre-knowledge that general frequency band(higher than 100 kHz) ultrasonic waves do not transmitted well due to severe attenuation. Our system includes ultrasonic pulser and receiver, transducers(50 kHz), acoustic hem, pneumatic controller and signal processing units (PC). In order to confirm the performance, several samples (apple, pear, persimmon, kiwi fruit, potato and radish) were tested, and the results showed sufficient possibility to apply to NDE of fruits and vegetables.

Advanced defect detection algorithm using clustering in ultrasonic NDE

Science.gov (United States)

Gongzhang, Rui; Gachagan, Anthony

2016-02-01

A range of materials used in industry exhibit scattering properties which limits ultrasonic NDE. Many algorithms have been proposed to enhance defect detection ability, such as the well-known Split Spectrum Processing (SSP) technique. Scattering noise usually cannot be fully removed and the remaining noise can be easily confused with real feature signals, hence becoming artefacts during the image interpretation stage. This paper presents an advanced algorithm to further reduce the influence of artefacts remaining in A-scan data after processing using a conventional defect detection algorithm. The raw A-scan data can be acquired from either traditional single transducer or phased array configurations. The proposed algorithm uses the concept of unsupervised machine learning to cluster segmental defect signals from pre-processed A-scans into different classes. The distinction and similarity between each class and the ensemble of randomly selected noise segments can be observed by applying a classification algorithm. Each class will then be labelled as `legitimate reflector' or `artefacts' based on this observation and the expected probability of defection (PoD) and probability of false alarm (PFA) determined. To facilitate data collection and validate the proposed algorithm, a 5MHz linear array transducer is used to collect A-scans from both austenitic steel and Inconel samples. Each pulse-echo A-scan is pre-processed using SSP and the subsequent application of the proposed clustering algorithm has provided an additional reduction to PFA while maintaining PoD for both samples compared with SSP results alone.

Application of advanced surface and volumetric NDE methods to the detection of cracks in critical regions of turbine blades

International Nuclear Information System (INIS)

Porter, J.P.

1990-01-01

Advanced NDE inspection techniques capable of detecting small, yet potentially dangerous cracks in turbine blade tenons, blade tie-wire through-holes, trailing edges, and blade root attachment ends have been devised and developed and are now being applied successfully in the field replacing conventional, less-sensitive methods commonly used for crack detection in these blade elements. Under-shroud lateral cracks in tenons are detected ultrasonically by highangle refracted pulse-echo shear wave and 0-degree pitch-catch longitudinal wave methods. Trailing-edge blade cracks and surface-connected cracks in root attachment ends are detected by high frequency eddy current techniques, typically applied remotely using ports in the turbine housing to gain access to the parts under inspection. Cracks emanating from tie-wire holes in blade upper ends are detected by eddy current inspection, which has been found to be a far more effective methods than either magnetic particle or ultrasonic testing for this application. Root attachment ends of side entry blades are inspected volumetrically by ultrasonics, using proprietary coupling techniques that allow examination of heretofore uninspectable regions of blade attachment hooks, known regions of crack initiation. Techniques developed for this collection of applications are described, and the results of actual field inspections are presented and discussed

A Study on the Guided Wave Mode Conversion using Self-calibrating Technique

International Nuclear Information System (INIS)

Park, Jung Chul; Cho, Youn Ho

2000-01-01

The guided wave mode conversion phenomena were investigated for the NDE of a plate-like structure with thickness variation. The ratios of reflection and transmission (R/T) were measured via the self-calibrating procedure which allows us to obtain experimental guided wave data in a more reliable way regardless of the coupling uncertainty between transducer and specimen. The results on R/T could be used to determine the thickness reduction of the structure. It was shown that not only the incident modes but also the converted ones need to be considered in the self-calibrating guided wave inspection to extract a reasonable correlation between experimental data and the thickness variation. Through this study, the potential of guided wave inspection as a quantitative NDE technique was explored based on the combined concept of self-calibration and multi-mode conversion in guided wave scattering problems

The use of fracture mechanics methodologies for NDT results evaluation and comparison

International Nuclear Information System (INIS)

Reale, S.

1995-01-01

In the general frame of analysing the interactions amongst the information from non destructive evaluation (NDE) and the methodologies to assess the integrity of a defective structure (such as fracture mechanics), the aim of the paper is to analyse and compare, in terms of indices related to safety margins, NDE results from round robin testing trials to acheive assessments of capabilities and limitations.A structural integrity/fracture mechanics approach for evaluating and comparing results from non destructive techniques is presented. Safety factors can be associated to flaws detected and characterized by inspections (estimated flaws) and to flaws actually present (reference flaws). The mismatch between safety factors associated to estimated flaws and safety factors associated to reference flaws can be used to assess capabilities and limitations of procedures and techniques in use for inspections.As an example, to show how the above procedure is applied and its potential as a method of data evaluation and comparison, the NDE results produced by the PISC (project for the inspection of steel components) activity have been considered. (orig.)

Strukturwandel, Verbandsabstinenz, Tarifflucht : zur Lage der Unternehmen und Arbeitgeberverbände im ostdeutschen verarbeitenden Gewerbe

OpenAIRE

Ettl, Wilfried; Heikenroth, André

1996-01-01

"Im Kontext der am Start der ostdeutschen Transformation vorgenommenen wirtschaftspolitischen Richtungsentscheidungen erwies sich die flächentarifvertragliche Normierung von Arbeits- und Entlohnungsbedingungen für die Arbeitgeberverbände als organisationspolitisch dysfunktional, weil sie der Differenzierung betriebswirtschaftlicher Kostenbedingungen und Interessenlagen im rasanten Strukturwandel nicht gerecht werden konnte. Anhand der Ergebnisse einer Befragung ostdeutscher ...

Multi-Wave and Hybrid Imaging Techniques: A New Direction for Nondestructive Testing and Structural Health Monitoring

Directory of Open Access Journals (Sweden)

Yuhua Cheng

2013-11-01

Full Text Available In this article, the state-of-the-art multi-wave and hybrid imaging techniques in the field of nondestructive evaluation and structural health monitoring were comprehensively reviewed. A new direction for assessment and health monitoring of various structures by capitalizing the advantages of those imaging methods was discussed. Although sharing similar system configurations, the imaging physics and principles of multi-wave phenomena and hybrid imaging methods are inherently different. After a brief introduction of nondestructive evaluation (NDE , structure health monitoring (SHM and their related challenges, several recent advances that have significantly extended imaging methods from laboratory development into practical applications were summarized, followed by conclusions and discussion on future directions.

The complementary roles of fracture mechanics and non-destructive examination in the safety assessment of components

International Nuclear Information System (INIS)

1988-01-01

This document presents the various speeches of the workshop of the Committee on Safety of Nuclear Installations (CSNI) that took place in Wuerenligen, Switzerland, in October 1988. The speeches deal with the roles of Non-Destructive Examination (NDE) and Fracture Mechanics (FM) in the safety assessment of reactor components, such as pressure vessels. Some calibration standards and reference values of defects are presented, and several NDE and FM methods for the assessment of components are described. Separate abstracts were prepared for all the papers in this volume. (TEC)

The complementary roles of fracture mechanics and non-destructive examination in the safety assessment of components

Energy Technology Data Exchange (ETDEWEB)

NONE

1988-12-31

This document presents the various speeches of the workshop of the Committee on Safety of Nuclear Installations (CSNI) that took place in Wuerenligen, Switzerland, in October 1988. The speeches deal with the roles of Non-Destructive Examination (NDE) and Fracture Mechanics (FM) in the safety assessment of reactor components, such as pressure vessels. Some calibration standards and reference values of defects are presented, and several NDE and FM methods for the assessment of components are described. Separate abstracts were prepared for all the papers in this volume. (TEC).

Applications of CIVA NDE 10 on Eddy Current Modeling

International Nuclear Information System (INIS)

Nurul Ain Ahmad Latif; Ilham Mukhriz Zainal Abidin; AABdul Razak Hamzah

2011-01-01

CIVA NDE 10 is the simulation software and used as the platform to develop the models dedicated to Eddy Current testing (ET). It has various application in semi analytical modeling approaches. The focus of this paper is to simulate the signals response on the 40 % external groove of the Inconel 600 heat exchanger tubes with outside diameter of 22.22 mm. The inspection were simulated using 17 mm outside diameter differential probe with 100 kHz and 500 kHZ testing frequency. All the simulation results were validated using the experimental results integrated in the CIVA software. The configurations of the probe and tube consisting the flaw show the good agreement between the experimental and the simulated data. (author)

Performance demonstration testing at the EPRI NDE center for intergranular stress corrosion cracking in BWR piping

International Nuclear Information System (INIS)

Pherigo, G.

1986-01-01

Intergranular stress corrosion cracking (IGSCC) has become a significant concern for the commercial electric utility industry during the past four years. As the IGSCC problem manifested itself, the Nuclear Regulatory Commission (NRC) responded by issuing Inspection and Enforcement (I and E) Bulletin 82-03 which required that ultrasonic inspection procedures be demonstrated on service- removed samples. The ability to reliably detect and discriminate IGSCC was recognized by the industry as a very difficult task, at best. Concurrent with the NRC bulletin, state-of-the-art yet practical techniques for the detection and discrimination of IGSCC had to be developed, demonstrated, and transferred to the field in a relatively short time. With the release of I and E Bulletin 83-02, procedures as well as personnel had to be qualified on service-removed samples. This paper reports how the EPRI Nondestructive Evaluation (NDE) Center developed the necessary technology and a formal training and qualification program to meet these needs on behalf of the industry

Üniversitelerde Hizmet Kalitesinin Servqual Analizi İle Ölçülmesi: Celal Bayar Üniversite’nde Bir Uygulama

OpenAIRE

GERŞİL, Mustafa; GÜVEN, Hüseyin

2018-01-01

Üniversiteler eğitim sistemiüzerinde stratejik öneme sahiptir. Hizmet kalitesini iyileştirme vegeliştirmenin ilk aşaması, hizmet kalitesinin ölçümüdür. Örgütler, sunmuşoldukları hizmetin kalitesi hakkında ne kadar fazla doğru ve güvenilirbilgilere sahip olursa, kalitenin daha yüksek düzeylere çıkarılması noktasındadaha etkin olabilirler. Bu çalışma, Celal Bayar Üniversitesi'nde hizmet kalitesininölçümünde SERVQUAL yöntemini kullanarak, öğrencilerin beklentilerini vealgılarını beş boyutta...

Directed Design of Experiments for Validating Probability of Detection Capability of NDE Systems (DOEPOD)

Science.gov (United States)

Generazio, Edward R.

2015-01-01

Directed Design of Experiments for Validating Probability of Detection Capability of NDE Systems (DOEPOD) Manual v.1.2 The capability of an inspection system is established by applications of various methodologies to determine the probability of detection (POD). One accepted metric of an adequate inspection system is that there is 95% confidence that the POD is greater than 90% (90/95 POD). Design of experiments for validating probability of detection capability of nondestructive evaluation (NDE) systems (DOEPOD) is a methodology that is implemented via software to serve as a diagnostic tool providing detailed analysis of POD test data, guidance on establishing data distribution requirements, and resolving test issues. DOEPOD demands utilization of observance of occurrences. The DOEPOD capability has been developed to provide an efficient and accurate methodology that yields observed POD and confidence bounds for both Hit-Miss or signal amplitude testing. DOEPOD does not assume prescribed POD logarithmic or similar functions with assumed adequacy over a wide range of flaw sizes and inspection system technologies, so that multi-parameter curve fitting or model optimization approaches to generate a POD curve are not required. DOEPOD applications for supporting inspector qualifications is included.

Classroom Assessment Techniques: A Literature Review

Science.gov (United States)

DiCarlo, Kristen; Cooper, Lori

2014-01-01

Effective classroom assessment techniques are directly linked to course objectives and proposed outcomes. Results within formative and summative assessments have been studied in the online learning environment as educators seek to meet objectives with respect to student success in the non-traditional setting. Online classroom assessment techniques…

Role of research in non-destructive evaluation for nuclear technology

International Nuclear Information System (INIS)

Jayakumar, T.; Rao, B.P.C.; Raj, Baldev

2010-01-01

This paper presents the role of research in non-destructive evaluation (NDE) of microstructures and mechanical properties in materials, assessment of manufacturing quality and early detection of in-service damage in nuclear components and structures. A few applications and case studies are discussed based on the results of systematic research and developmental activities pursued in different NDE techniques at the authors' laboratory for three different types of Indian nuclear reactors. (author)

Nondestructive Evaluation and Monitoring Results from COPV Accelerated Stress Rupture Testing, NASA White Sands Test Facility (WSTF)

Science.gov (United States)

Saulsberry Regor

2010-01-01

Develop and demonstrate NDE techniques for real-time characterization of CPVs and, where possible, identification of NDE capable of assessing stress rupture related strength degradation and/or making vessel life predictions (structural health monitoring or periodic inspection modes). Secondary: Provide the COPV user and materials community with quality carbon/epoxy (C/Ep) COPV stress rupture progression rate data. Aid in modeling, manufacturing, and application of COPVs for NASA spacecraft.

Qualification of non-destructive examination for belgian nuclear reactor pressure vessel inspection

International Nuclear Information System (INIS)

Couplet, D.; Francoise, T.

2001-01-01

In Service Inspection (ISI) participates to the assessment of Nuclear Reactor Pressure Vessel Integrity. The performance of Non Destructive Examination (NDE) techniques must be demonstrated according to predefined objectives. The qualification process is essential to trust the reliability of the information provided by NDE. In Belgian Nuclear Power Plants, the qualification was conducted through a collaboration between the vendor and a technical group from the Electricity Utility. The important facts of this qualification will be presented: - the detailed definition of the inspection and qualifications objectives, based on a combination of the ASME code and the European Methodology for Qualification; - the systematic verification of the NDE performance and limitations, for each ISI objective, through an adequate combination of tests on blocks and technical justification; - the continuous improvement of the NDE procedure; - the feedback and the lessons learnt from site experience; - the necessary multi-disciplinary approach (NDE, degradation mechanisms, structural integrity)

Precision Learning Assessment: An Alternative to Traditional Assessment Techniques.

Science.gov (United States)

Caltagirone, Paul J.; Glover, Christopher E.

1985-01-01

A continuous and curriculum-based assessment method, Precision Learning Assessment (PLA), which integrates precision teaching and norm-referenced techniques, was applied to a math computation curriculum for 214 third graders. The resulting districtwide learning curves defining average annual progress through the computation curriculum provided…

Reliability and comparison of acromion assessment techniques on x-ray and magnetic resonance imaging (reliability of acromion assessment techniques)

International Nuclear Information System (INIS)

Viskontas, D.G.; MacDermid, J.C.; Drosdowech, D.S.; Garvin, G.J.; Romano, W.M.; Faber, K.J.

2005-01-01

To determine the reliability and correlation of plain radiography and magnetic resonance imaging (MRI) in the assessment of acromion morphology. Materials and Methods: Acromion morphology was assessed using the lateral acromion angle (LAA) and the acromion-humeral interval (AHI). Thirty patients who had x-rays and MRI for impingement syndrome were included. Six blinded observers assessed the acromion morphology subjectively and objectively. Results: Neither acromion assessment technique demonstrated a positive correlation (kappa and intraclass coefficient 0.55) when measured objectively by experienced observers. Conclusion: The LAA and the AHI are both reliable acromion assessment techniques on X-ray and MRI when measured objectively and by experienced observers. (author)

European-American workshop: Determination of reliability and validation methods on NDE. Proceedings

International Nuclear Information System (INIS)

1997-01-01

The invited papers focused on the following issues: 1. The different technical and scientific approaches to the problem of how to guarantees or demonstrate the reliability of NDE: a. Application of established prescriptive standards, b. Probabilities of Detection (PDO) and False Alarm (PFA) from blind trials, c. POD and PFA from signal statistics, d. Modeling, e. ''Technical Justification''; 2. The dissimilar validation/qualification concepts used in different industries in Europe and North America: a. Nuclear Power Generation, b. Aerospace Industry, c. Offcshore Industry and d. Service Companies

Light Water Reactor Sustainability (LWRS) Program – Non-Destructive Evaluation (NDE) R&D Roadmap for Determining Remaining Useful Life of Aging Cables in Nuclear Power Plants

Energy Technology Data Exchange (ETDEWEB)

Simmons, Kevin L.; Ramuhalli, Pradeep; Brenchley, David L.; Coble, Jamie B.; Hashemian, Hash; Konnik, Robert; Ray, Sheila

2012-09-14

The purpose of the non-destructive evaluation (NDE) R&D Roadmap for Cables is to support the Materials Aging and Degradation (MAaD) R&D pathway. The focus of the workshop was to identify the technical gaps in detecting aging cables and predicting their remaining life expectancy. The workshop was held in Knoxville, Tennessee, on July 30, 2012, at Analysis and Measurement Services Corporation (AMS) headquarters. The workshop was attended by 30 experts in materials, electrical engineering, U.S. Nuclear Regulatory Commission (NRC), U.S. Department of Energy (DOE) National Laboratories (Oak Ridge National Laboratory, Pacific Northwest National Laboratory, Argonne National Laboratory, and Idaho National Engineering Laboratory), NDE instrumentation development, universities, commercial NDE services and cable manufacturers, and Electric Power Research Institute (EPRI). The motivation for the R&D roadmap comes from the need to address the aging management of in-containment cables at nuclear power plants (NPPs).

An Advanced Ultrasonic Imaging System using Time-Reversal MUSIC Technique for Rapid Inspection of Ultra Large, Complex Composite Structures, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — NASA seeks advanced Nondestructive Evaluation (NDE) sensor systems with advanced processing and displays to provide reliable assessments of the location and severity...

Prospects on the application of HTS SQUID magnetometry to nondestructive evaluation (NDE)

Science.gov (United States)

Weinstock, H.

1993-04-01

In light of recent advances in the fabrication of low-noise HTS SQUIDs, a review is presented on the use of LTS SQUID magnetometry for nondestructive evaluation (NDE). Examples are given on applications relating to defects in steel, subsurface cracks in aircraft frames, and voids in non-metallic structures. HTS SQUIDs may make a significant difference in the acceptance of these applications because sensing coils will be closer to a sample under test, there will be greater instrument portability and the problem of bringing liquid helium to remote locations will be eliminated.

Applications of ultrasonic phased array technique during fabrication of nuclear tubing and other components for the Indian nuclear power program

International Nuclear Information System (INIS)

Kapoor, K.

2015-01-01

Ultrasonic phased array technique has been applied in fabrication of nuclear fuel and structural at NFC. The integrity of the nuclear fuel and structural components is most crucial as they are exposed to severe environment during operation leading to rapid degradation of its properties during its lifecycle. Nuclear Fuel Complex has mandate for the fabrication of the nuclear fuel and core structurals for Indian PHWRs/BWR, sub-assemblies for the PFBR and steam generator tubing for PFBR and PHWRs which are the most critical materials for the Indian Nuclear Power program. NDE during fabrication of these materials is thus most crucial as it provides the confidence to the designer for safe operation during its lifetime. Many of these techniques have to be developed in-house to meet unique requirements of high sensitivity, resolution and shape of the components. Some of the advancements in the NDE during the fabrication include use of ultrasonic phased array which is detailed in this paper

Safety assessment of primary system components at the USNRC

Energy Technology Data Exchange (ETDEWEB)

Serpan, C Z; Chen, C Y; Taboada, A

1988-12-31

This document deals with the safety assessment in nuclear reactor components at the USNRC. The USNRC regulations and requirements concerning nuclear reactor design and operations are presented, together with guides and standards which describe how the actions should be implemented. The safety assessment relies on fracture analysis and Non Destructive Examination (NDE). (TEC).

Statistical reliability assessment of UT round-robin test data for piping welds

International Nuclear Information System (INIS)

Kim, H.M.; Park, I.K.; Park, U.S.; Park, Y.W.; Kang, S.C.; Lee, J.H.

2004-01-01

Ultrasonic NDE is one of important technologies in the life-time maintenance of nuclear power plant. Ultrasonic inspection system is consisted of the operator, equipment and procedure. The reliability of ultrasonic inspection system is affected by its ability. The performance demonstration round robin was conducted to quantify the capability of ultrasonic inspection for in-service. Several teams employed procedures that met or exceeded with ASME sec. XI code requirements detected the piping of nuclear power plant with various cracks to evaluate the capability of detection and sizing. In this paper, the statistical reliability assessment of ultrasonic nondestructive inspection data using probability of detection (POD) is presented. The result of POD using logistic model was useful to the reliability assessment for the NDE hit or miss data. (orig.)

Review of NRC-funded programs on NDE at Pacific Northwest Laboratory

International Nuclear Information System (INIS)

Doctor, S.R.

1983-04-01

There are currently four major NDT related programs in progress at PNL which are funded by the US Nuclear Regulatory Commission. These programs are Integration of NDE and Fracture Mechanics Program, Development of a Real-Time SAFT-UT System for the Inservice Inspection of LWRs, Acoustic Emission - Flaw Relationships for Inservice Monitoring of Nuclear Reactor Pressure Boundaries, and Steam Generator Integrity Program/Steam Generator Group Project. This paper will discuss and present an overview of each program and highlight the more significant accomplishments obtained to date. All of these programs have been funded for several years and are scheduled for completion in 1985 or 1986

Nondestructive Evaluation of Thick Concrete Using Advanced Signal Processing Techniques

Energy Technology Data Exchange (ETDEWEB)

Clayton, Dwight A [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Barker, Alan M [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Santos-Villalobos, Hector J [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Albright, Austin P [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hoegh, Kyle [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Khazanovich, Lev [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-09-01

The purpose of the U.S. Department of Energy Office of Nuclear Energy’s Light Water Reactor Sustainability (LWRS) Program is to develop technologies and other solutions that can improve the reliability, sustain the safety, and extend the operating lifetimes of nuclear power plants (NPPs) beyond 60 years [1]. Since many important safety structures in an NPP are constructed of concrete, inspection techniques must be developed and tested to evaluate the internal condition. In-service containment structures generally do not allow for the destructive measures necessary to validate the accuracy of these inspection techniques. This creates a need for comparative testing of the various nondestructive evaluation (NDE) measurement techniques on concrete specimens with known material properties, voids, internal microstructure flaws, and reinforcement locations.

¿Cómo y dónde evalúa el cerebro las consecuencias de nuestras decisiones?

Directory of Open Access Journals (Sweden)

José L. Pardo-Vázquez

2010-02-01

Full Text Available Para aprender de la experiencia y ajustar nuestro comportamiento necesitamos evaluar las consecuencias de nuestra conducta. ¿Cómo y dónde tiene lugar esta evaluación en el cerebro? Recientemente hemos descrito que la información necesaria para alcanzar una decisión y evaluar sus consecuencias está representada en la corteza premotora ventral.

Materials science research for sodium cooled fast reactors

Indian Academy of Sciences (India)

Administrator

puter simulation and modeling, manufacturing, repair and in-service inspection. ... production of fuel for nuclear reactors. ... reactor design are being carefully analysed with the aim ...... vanced NDE techniques for assessment of manufactured.

RUSÇUK VE ÇEVRESİNDE CEREHORLAR (1694-1698)

OpenAIRE

Çolak, Kamil

2018-01-01

Osmanlı Devleti’nde ücret karşılığı geçici olarak geri hizmetlerde kullanılan askerlere cerehor adı verilmiştir. Cerehorlar genellikle kale tamiri, yol, köprü, gemi, tabya inşası, maden ocakları, bataklık temizleme, siper kazma, gemilerde kürek çekme gibi işlerde çalıştırılmışlardır. Bu arada devlete ait bazı işlerin yapılması durumunda cerehorluktan muaf olunabilmiştir. Rusçuk şehri Tuna Nehri kıyısında yer aldığından buradan temin edilen cerehorlar büyük ölçüde gemilerde kürek çekmişlerdir....

Automatic identification of corrosion damage using image processing techniques

Energy Technology Data Exchange (ETDEWEB)

Bento, Mariana P.; Ramalho, Geraldo L.B.; Medeiros, Fatima N.S. de; Ribeiro, Elvis S. [Universidade Federal do Ceara (UFC), Fortaleza, CE (Brazil); Medeiros, Luiz C.L. [Petroleo Brasileiro S.A. (PETROBRAS), Rio de Janeiro, RJ (Brazil)

2009-07-01

This paper proposes a Nondestructive Evaluation (NDE) method for atmospheric corrosion detection on metallic surfaces using digital images. In this study, the uniform corrosion is characterized by texture attributes extracted from co-occurrence matrix and the Self Organizing Mapping (SOM) clustering algorithm. We present a technique for automatic inspection of oil and gas storage tanks and pipelines of petrochemical industries without disturbing their properties and performance. Experimental results are promising and encourage the possibility of using this methodology in designing trustful and robust early failure detection systems. (author)

NDE of stainless steel and on-line leak monitoring of LWRs. Annual report, October 1984-September 1985. Volume 2

International Nuclear Information System (INIS)

Kupperman, D.S.; Claytor, T.N.; Mathieson, T.; Prine, D.W.

1986-02-01

This progress report summarizes work performed by the Argonne National Laboratory and GARD, Inc. (Division of Chamberlain Mfg. Corp.) as subcontractor on NDE of stainless steel and on-line leak monitoring of LWRs during the 12 months from October 1984 to September 1985. 15 refs., 36 figs

Välismaalaste seaduses sätestatud töö- ja ettevõtlusrände regulatsiooni väärkasutamine Eestis ja äriseadustiku muudatuste mõju töö- ja ettevõtlusrände regulatsiooni väärkasutamisele : [magistritöö] / Laura Sofia Annus ; Tartu Üliko

Index Scriptorium Estoniae

Annus, Laura Sofia

2012-01-01

Välismaalase mõistest ja tähtajalise elamisloa regulatsioonist, ettevõtte asutamise regulatsioonist, töö- ja ettevõtlusrände regulatsiooni mitte-eesmärgipärasest kasutamisest ja lahendustest selle peatamiseks

KRISENZUSTÄNDE UND ANWENDUNG VON ZWANGSMASSNAHMEN IN DER PSYCHIATRIE

Directory of Open Access Journals (Sweden)

Vesna Šendula Jengić

2017-01-01

Full Text Available In der Arbeit wird über die Phänomene der Aggressivität und Gewalt bei Menschen diskutiert, wobei man besonderen Wert auf die Personen mit seelischen Störungen legt. Krisenzustände und Gewaltverhalten gibt es nicht nur in der Psychiatrie. Es kann immer zu einem solchem Zustand und Verhalten kommen und jeder kann unter bestimmten Umständen sowohl Opfer als auch Täter sein. Multikausalität und Komplexität sowie auch individuelle Umstände und situationsbezogene Faktoren, welche zum Gewaltverhalten führen können, haben nur geringen Prognosekraft. Statistische Indikatoren andererseits können falsch positive und falsch negative Ergebnisse verbergen, wobei ein Fehler in der Einschätzung das Risiko zum Erscheinen eines Verhaltens drastisch erhöhen oder zum unrechtfertigten Entziehung der Freiheit führen kann. Zwangsmaβnahmen in der Psychiatrie sind nur ausnahmsweise anzuwenden, und zwar, wenn ein gefährliches Verhalten direkt das Leben und die Gesundheit einer Person oder einer Umgebung gefährdet. Darüber hinaus ist die Dauer von Zwangsmaβnahmen auch beschränkt. Die Gesetzesregulative, insbesondere das Gesetz über den Schutz von Personen mit seelischen Störungen (Amtsblatt der Republik Kroatien Nr. 76/2014 und die Ordnung über die Arten und die Weise der Anwendung von Zwangsmaβnahmen gegenüber den Personen mit schwierigen seelischen Störungen (Amtsblatt der Republik Kroatien Nr. 16/2015, dient als zusätzlicher Schutz der Rechte dieser Patientengruppe und schreibt die Arten und die Weise der Anwendung von Zwangsmaβnahmen sowie auch die Vorgehensweise. Zusätzliche Richtlinien und Vorgehensstrategien wurden auch von den Gesellschaften für Psychiatrie gegeben. In der Arbeit wird betont, dass bessere Bedingungen, Infrastruktur und Arbeitskräfte sowie auch ständige Entwicklung und Bewertung der Arbeitsqualität in der Psychiatrie erforderlich sind. Abschlieβend werden Standards und ethische Fragen in Betracht gezogen, wie

Electromagnetic characterization of white spruce at different moisture contents using synthetic aperture radar imaging

Science.gov (United States)

Ingemi, Christopher M.; Owusu Twumasi, Jones; Yu, Tzuyang

2018-03-01

Detection and quantification of moisture content inside wood (timber) is key to ensuring safety and reliability of timber structures. Moisture inside wood attracts insects and fosters the development of fungi to attack the timber, causing significant damages and reducing the load bearing capacity during their design life. The use of non-destructive evaluation (NDE) techniques (e.g., microwave/radar, ultrasonic, stress wave, and X-ray) for condition assessment of timber structures is a good choice. NDE techniques provide information about the level of deterioration and material properties of timber structures without obstructing their functionality. In this study, microwave/radar NDE technique was selected for the characterization of wood at different moisture contents. A 12 in-by-3.5 in-by-1.5 in. white spruce specimen (picea glauca) was imaged at different moisture contents using a 10 GHz synthetic aperture radar (SAR) sensor inside an anechoic chamber. The presence of moisture was found to increase the SAR image amplitude as expected. Additionally, integrated SAR amplitude was found beneficial in modeling the moisture content inside the wood specimen.

A comparative evaluation of five human reliability assessment techniques

International Nuclear Information System (INIS)

Kirwan, B.

1988-01-01

A field experiment was undertaken to evaluate the accuracy, usefulness, and resources requirements of five human reliability quantification techniques (Techniques for Human Error Rate Prediction (THERP); Paired Comparisons, Human Error Assessment and Reduction Technique (HEART), Success Liklihood Index Method (SLIM)-Multi Attribute Utility Decomposition (MAUD), and Absolute Probability Judgement). This was achieved by assessing technique predictions against a set of known human error probabilities, and by comparing their predictions on a set of five realistic Probabilisitc Risk Assessment (PRA) human error. On a combined measure of accuracy THERP and Absolute Probability Judgement performed best, whilst HEART showed indications of accuracy and was lower in resources usage than other techniques. HEART and THERP both appear to benefit from using trained assessors in order to obtain the best results. SLIM and Paired Comparisons require further research on achieving a robust calibration relationship between their scale values and absolute probabilities. (author)

Assessment Techniques in the Second-Cycle Studies

Directory of Open Access Journals (Sweden)

Jurgita Kerevičienė

2011-06-01

Full Text Available Assessment and evaluation are among the essential functions performed by an educator. What is more, they are closely related to the communication of the teaching process efficiency in terms of verification of learner and educator expectations, determination of learning and teaching quality achievement, and generalization of educational activities. The present study aims at the analysis of assessment techniques applied in the master degree linguistic studies. Initially, a brief theoretical overview of both formal and informal assessment me- thods is provided, with the focus on their distinctive features and ways of application in the light of Bloom’s taxonomy and Dublin description representing the competence requirements set for the gain of definite skills. Further, the results of the survey (conducted at Kaunas Faculty of Humanities, Vilnius University are described. Finally, the eligible assessment techniques serving the purpose of efficient educational process in the second-cycle study process are identified.

Enhancing the capabilities of eddy current techniques for non-destructive evaluation of austenitic stainless steels

International Nuclear Information System (INIS)

Rao, B.P.C.; Thirunavukkarasu, S.; Sasi, B.; Jayakumar, T.; Baldev Raj

2010-01-01

Eddy current non-destructive evaluation (NDE) techniques find many applications during fabrication and in-service inspection of components made of stainless steel. In recent years, concurrent developments in electromagnetic field detection sensors such as giant magneto-resistive (GMR), giant-magneto impedance (GMI) and SQUIDs sensors, computers, microelectronics, and incorporating advanced signal and image processing techniques, have paved the way for enhancing the capabilities of existing eddy current (EC) techniques for examination of austenitic stainless steel (SS) plates, tubes and other geometries and several innovative methodologies have been developed. This paper highlights a few such applications in EC testing to austenitic stainless steel components used in fast reactors. (author)

Development of acoustic model-based iterative reconstruction technique for thick-concrete imaging

Science.gov (United States)

Almansouri, Hani; Clayton, Dwight; Kisner, Roger; Polsky, Yarom; Bouman, Charles; Santos-Villalobos, Hector

2016-02-01

Ultrasound signals have been used extensively for non-destructive evaluation (NDE). However, typical reconstruction techniques, such as the synthetic aperture focusing technique (SAFT), are limited to quasi-homogenous thin media. New ultrasonic systems and reconstruction algorithms are in need for one-sided NDE of non-homogenous thick objects. An application example space is imaging of reinforced concrete structures for commercial nuclear power plants (NPPs). These structures provide important foundation, support, shielding, and containment functions. Identification and management of aging and degradation of concrete structures is fundamental to the proposed long-term operation of NPPs. Another example is geothermal and oil/gas production wells. These multi-layered structures are composed of steel, cement, and several types of soil and rocks. Ultrasound systems with greater penetration range and image quality will allow for better monitoring of the well's health and prediction of high-pressure hydraulic fracturing of the rock. These application challenges need to be addressed with an integrated imaging approach, where the application, hardware, and reconstruction software are highly integrated and optimized. Therefore, we are developing an ultrasonic system with Model-Based Iterative Reconstruction (MBIR) as the image reconstruction backbone. As the first implementation of MBIR for ultrasonic signals, this paper document the first implementation of the algorithm and show reconstruction results for synthetically generated data.1

Development of Acoustic Model-Based Iterative Reconstruction Technique for Thick-Concrete Imaging

Energy Technology Data Exchange (ETDEWEB)

Almansouri, Hani [Purdue University; Clayton, Dwight A [ORNL; Kisner, Roger A [ORNL; Polsky, Yarom [ORNL; Bouman, Charlie [Purdue University; Santos-Villalobos, Hector J [ORNL

2016-01-01

Ultrasound signals have been used extensively for non-destructive evaluation (NDE). However, typical reconstruction techniques, such as the synthetic aperture focusing technique (SAFT), are limited to quasi-homogenous thin media. New ultrasonic systems and reconstruction algorithms are in need for one-sided NDE of non-homogenous thick objects. An application example space is imaging of reinforced concrete structures for commercial nuclear power plants (NPPs). These structures provide important foundation, support, shielding, and containment functions. Identification and management of aging and degradation of concrete structures is fundamental to the proposed long-term operation of NPPs. Another example is geothermal and oil/gas production wells. These multi-layered structures are composed of steel, cement, and several types of soil and rocks. Ultrasound systems with greater penetration range and image quality will allow for better monitoring of the well's health and prediction of high-pressure hydraulic fracturing of the rock. These application challenges need to be addressed with an integrated imaging approach, where the application, hardware, and reconstruction software are highly integrated and optimized. Therefore, we are developing an ultrasonic system with Model-Based Iterative Reconstruction (MBIR) as the image reconstruction backbone. As the first implementation of MBIR for ultrasonic signals, this paper document the first implementation of the algorithm and show reconstruction results for synthetically generated data.

Development of Acoustic Model-Based Iterative Reconstruction Technique for Thick-Concrete Imaging

Energy Technology Data Exchange (ETDEWEB)

Almansouri, Hani [Purdue University; Clayton, Dwight A [ORNL; Kisner, Roger A [ORNL; Polsky, Yarom [ORNL; Bouman, Charlie [Purdue University; Santos-Villalobos, Hector J [ORNL

2015-01-01

Ultrasound signals have been used extensively for non-destructive evaluation (NDE). However, typical reconstruction techniques, such as the synthetic aperture focusing technique (SAFT), are limited to quasi-homogenous thin media. New ultrasonic systems and reconstruction algorithms are in need for one-sided NDE of non-homogenous thick objects. An application example space is imaging of reinforced concrete structures for commercial nuclear power plants (NPPs). These structures provide important foundation, support, shielding, and containment functions. Identification and management of aging and degradation of concrete structures is fundamental to the proposed long-term operation of NPPs. Another example is geothermal and oil/gas production wells. These multi-layered structures are composed of steel, cement, and several types of soil and rocks. Ultrasound systems with greater penetration range and image quality will allow for better monitoring of the well s health and prediction of high-pressure hydraulic fracturing of the rock. These application challenges need to be addressed with an integrated imaging approach, where the application, hardware, and reconstruction software are highly integrated and optimized. Therefore, we are developing an ultrasonic system with Model-Based Iterative Reconstruction (MBIR) as the image reconstruction backbone. As the first implementation of MBIR for ultrasonic signals, this paper document the first implementation of the algorithm and show reconstruction results for synthetically generated data.

Effectiveness of teachers' training in assessment techniques: participants' perception.

Science.gov (United States)

Baral, N; Gautam, A; Lamsal, M; Paudel, B H; Lal Das, B K; Aryal, M

2011-01-01

Medical education has experienced a rapidly changing scenario especially during the past three decades. Teachers training programs have emerged in recent years as a more in depth and comprehensive mechanisms for strengthening instructional skills and formulating assessment techniques among faculty members. The present study was carried out with the aim of assessing effectiveness of teacher training workshop on assessment techniques at B.P. Koirala Institute of Health sciences (BPKIHS), Dharan, Nepal. Methods: In this prospective questionnaire based study, the 26 entry level teachers were enrolled. They were requested to fill the questionnaire before and after the workshop on the assessment techniques at BPKIHS, Dharan. Twenty six teachers majority of whom were entry level teachers comprising of medical, dental, nursing and allied sciences participated in pre- and post test analysis on the various components of written and oral examinations. A two and half days long training was conducted having 9 hours of teaching interactive sessions, 6 hours of group exercises, daily evaluation and 3 hours of presentation by participants. There was high degree of agreement with most topics of the assessment training. There was a significant gain in knowledge (p training being informative and learned new things about assessment. More practice session with longer duration with invited resource persons were also suggested for an effective session. Thereis an immense opportunity for a better and comprehensive training in evaluation techniques in medical education..

Incorporation of composite defects from ultrasonic NDE into CAD and FE models

Science.gov (United States)

Bingol, Onur Rauf; Schiefelbein, Bryan; Grandin, Robert J.; Holland, Stephen D.; Krishnamurthy, Adarsh

2017-02-01

Fiber-reinforced composites are widely used in aerospace industry due to their combined properties of high strength and low weight. However, owing to their complex structure, it is difficult to assess the impact of manufacturing defects and service damage on their residual life. While, ultrasonic testing (UT) is the preferred NDE method to identify the presence of defects in composites, there are no reasonable ways to model the damage and evaluate the structural integrity of composites. We have developed an automated framework to incorporate flaws and known composite damage automatically into a finite element analysis (FEA) model of composites, ultimately aiding in accessing the residual life of composites and make informed decisions regarding repairs. The framework can be used to generate a layer-by-layer 3D structural CAD model of the composite laminates replicating their manufacturing process. Outlines of structural defects, such as delaminations, are automatically detected from UT of the laminate and are incorporated into the CAD model between the appropriate layers. In addition, the framework allows for direct structural analysis of the resulting 3D CAD models with defects by automatically applying the appropriate boundary conditions. In this paper, we show a working proof-of-concept for the composite model builder with capabilities of incorporating delaminations between laminate layers and automatically preparing the CAD model for structural analysis using a FEA software.

Bulk ultrasonic NDE of metallic components at high temperature using magnetostrictive transducers

Science.gov (United States)

Ashish, Antony Jacob; Rajagopal, Prabhu; Balasubramaniam, Krishnan; Kumar, Anish; Rao, B. Purnachandra; Jayakumar, Tammana

2017-02-01

Online ultrasonic NDE at high-temperature is of much interest to the power, process and automotive industries in view of possible savings in downtime. This paper describes a novel approach to developing ultrasonic transducers capable of high-temperature in-situ operation using the principle of magnetostriction. Preliminary design from previous research by the authors [1] is extended for operation at 1 MHz, and at elevated temperatures by amorphous metallic strips as the magnetostrictive core. Ultrasonic signals in pulse-echo mode are experimentally obtained from the ultrasonic transducer thus developed, in a simulated high-temperature environment of 350 °C for 10 hours. Advantages and challenges for practical deployment of this approach are discussed.

Objective techniques for psychological assessment

Science.gov (United States)

Wortz, E.; Hendrickson, W.; Ross, T.

1973-01-01

A literature review and a pilot study are used to develop psychological assessment techniques for determining objectively the major aspects of the psychological state of an astronaut. Relationships between various performance and psychophysiological variables and between those aspects of attention necessary to engage successfully in various functions are considered in developing a paradigm to be used for collecting data in manned isolation chamber experiments.

Multi-intelligence critical rating assessment of fusion techniques (MiCRAFT)

Science.gov (United States)

Blasch, Erik

2015-06-01

Assessment of multi-intelligence fusion techniques includes credibility of algorithm performance, quality of results against mission needs, and usability in a work-domain context. Situation awareness (SAW) brings together low-level information fusion (tracking and identification), high-level information fusion (threat and scenario-based assessment), and information fusion level 5 user refinement (physical, cognitive, and information tasks). To measure SAW, we discuss the SAGAT (Situational Awareness Global Assessment Technique) technique for a multi-intelligence fusion (MIF) system assessment that focuses on the advantages of MIF against single intelligence sources. Building on the NASA TLX (Task Load Index), SAGAT probes, SART (Situational Awareness Rating Technique) questionnaires, and CDM (Critical Decision Method) decision points; we highlight these tools for use in a Multi-Intelligence Critical Rating Assessment of Fusion Techniques (MiCRAFT). The focus is to measure user refinement of a situation over the information fusion quality of service (QoS) metrics: timeliness, accuracy, confidence, workload (cost), and attention (throughput). A key component of any user analysis includes correlation, association, and summarization of data; so we also seek measures of product quality and QuEST of information. Building a notion of product quality from multi-intelligence tools is typically subjective which needs to be aligned with objective machine metrics.

Non-destructive and destructive examination of the retired North Anna 2 Reactor Pressure Vessel Head

International Nuclear Information System (INIS)

Ahluwalia, Kawaljit; Barnes, Robert; Rao, Gutti; Cattant, Francois; Peat, Noel

2006-09-01

Stress corrosion cracking of Alloy 600 and nickel-based weld materials has been the single biggest challenge facing the PWR industry. A fundamental and thorough knowledge was needed to properly explain this phenomenon and develop appropriate mitigation strategies. Non Destructive Examination (NDE) of the North Anna Unit 2 Reactor Vessel Head (RVH) during the 2002 fall outage identified widespread crack indications in the Alloy 600 CRDM penetrations and associated Alloy 182 and 82 J-groove attachment welds. When the Utility decided to replace the RVH, a rare opportunity was provided to the industry to undertake in-depth studies of representative defective CRDM penetrations from a retired RVH. Accordingly, the Materials Reliability Program, undertook a two-phase program on the retired North Anna 2 Alloy 600 RVH. The first phase involved selection and removal of six penetrations from the RVH and penetration decontamination, replication and laboratory NDE. The second phase consisted of a detailed destructive examination of penetration number 54. This paper provides a summary of work undertaken during this program. Criteria for selection of penetrations for removal and procedures used in removal of the penetrations are described. Extreme care was undertaken in decontamination of the penetrations to facilitate laboratory NDE. Penetration number 54 was then subjected to destructive examination to establish a correlation between NDE findings (from both field and laboratory inspections) and actual flaws. Additional objectives of the destructive examination included mechanistic assessment of defect formation and investigation of the annulus environment and wastage characterization. Data obtained from these studies is invaluable in validating safety assessment statements by developing the correlation between field NDE and actual defects. In addition, information gathered from non-destructive and destructive examinations is used to assess accuracy of the NDE techniques

SAKARYA İLİNDE 17 AGUSTOS 1999 DEPREMiNDE HASAR GÖREN Y APlLAR ÜZERİNE BİR ARAŞTIRMA

Directory of Open Access Journals (Sweden)

Fatih İLÇİ

2003-08-01

Full Text Available Doğal afetler aras ı nda , yapılara en büyük zararı depremler venniş ti r. Bunun için, her an deprem olacakmış gibi h az ı r olun ınalıdır. Ya p ı yapma fikri( daha y e ni ohışına aşan1asında i ken , inşaat sektörü ile ilgili tünı meslek grupları s ürekli bir ko o rd in asy on n ç i nde çalışnıalıdır. Bu ko ordi ne l i çalışnıa neticesinde; 17 Ağustos 1999 d epremini n türrı ol ums uz sonuçlan iyi bir şekilde anl aşılıp, dcpreme karşı nas ı l dayanıklı yapı yapabili rim. Fikri benimsenmelidir.

Elastic wave scattering methods: assessments and suggestions

International Nuclear Information System (INIS)

Gubernatis, J.E.

1985-01-01

The author was asked by the meeting organizers to review and assess the developments over the past ten or so years in elastic wave scattering methods and to suggest areas of future research opportunities. He highlights the developments, focusing on what he feels were distinct steps forward in our theoretical understanding of how elastic waves interact with flaws. For references and illustrative figures, he decided to use as his principal source the proceedings of the various annual Reviews of Progress in Quantitative Nondestructive Evaluation (NDE). These meetings have been the main forum not only for presenting results of theoretical research but also for demonstrating the relevance of the theoretical research for the design and interpretation of experiment. In his opinion a quantitative NDE is possible only if this relevance exists, and his major objective is to discuss and illustrate the degree to which relevance has developed

Assessing the accuracy of remote sensing techniques in vegetation ...

African Journals Online (AJOL)

Assessing the accuracy of remote sensing techniques in vegetation fractions estimation. ... This study aimed at exploring different remote sensing (RS) techniques for quantitatively measuring vegetation and bare soil ... HOW TO USE AJOL.

Towards ABET accreditation for a SWE program: alternative student assessment techniques

International Nuclear Information System (INIS)

Alghamdi, A.; Nasir, M.; Alnafjan, K.

2011-01-01

This paper describes assessment techniques utilized for assessing undergraduate students studying in a software engineering program. The purpose behind this work is to get the program accredited by the Accreditation Board of Engineering and Technology (ABET). Therefore, a number of applied direct and indirect assessment techniques are described. These techniques are implemented towards the end of the semester to assess the extent to which the student and course outcomes are satisfied. Consequently, results are obtained and analyzed and various learning issues are eventually identified. Finally, the paper provides suggestions for improvement in course delivery as well as learning mechanism. (author)

Advanced methods in NDE using machine learning approaches

Science.gov (United States)

Wunderlich, Christian; Tschöpe, Constanze; Duckhorn, Frank

2018-04-01

Machine learning (ML) methods and algorithms have been applied recently with great success in quality control and predictive maintenance. Its goal to build new and/or leverage existing algorithms to learn from training data and give accurate predictions, or to find patterns, particularly with new and unseen similar data, fits perfectly to Non-Destructive Evaluation. The advantages of ML in NDE are obvious in such tasks as pattern recognition in acoustic signals or automated processing of images from X-ray, Ultrasonics or optical methods. Fraunhofer IKTS is using machine learning algorithms in acoustic signal analysis. The approach had been applied to such a variety of tasks in quality assessment. The principal approach is based on acoustic signal processing with a primary and secondary analysis step followed by a cognitive system to create model data. Already in the second analysis steps unsupervised learning algorithms as principal component analysis are used to simplify data structures. In the cognitive part of the software further unsupervised and supervised learning algorithms will be trained. Later the sensor signals from unknown samples can be recognized and classified automatically by the algorithms trained before. Recently the IKTS team was able to transfer the software for signal processing and pattern recognition to a small printed circuit board (PCB). Still, algorithms will be trained on an ordinary PC; however, trained algorithms run on the Digital Signal Processor and the FPGA chip. The identical approach will be used for pattern recognition in image analysis of OCT pictures. Some key requirements have to be fulfilled, however. A sufficiently large set of training data, a high signal-to-noise ratio, and an optimized and exact fixation of components are required. The automated testing can be done subsequently by the machine. By integrating the test data of many components along the value chain further optimization including lifetime and durability

Modelling NDE pulse-echo inspection of misorientated planar rough defects using an elastic finite element method

Energy Technology Data Exchange (ETDEWEB)

Pettit, J. R.; Lowe, M. J. S. [UK Research Centre for NDE, Imperial College London, Exhibition Road, London, SW7 2AZ (United Kingdom); Walker, A. E. [Rolls-Royce Nuclear, PO BOX 2000, Derby, DE21 7XX (United Kingdom)

2015-03-31

Pulse-echo ultrasonic NDE examination of large pressure vessel forgings is a design and construction code requirement in the power generation industry. Such inspections aim to size and characterise potential defects that may have formed during the forging process. Typically these defects have a range of orientations and surface roughnesses which can greatly affect ultrasonic wave scattering behaviour. Ultrasonic modelling techniques can provide insight into defect response and therefore aid in characterisation. However, analytical approaches to solving these scattering problems can become inaccurate, especially when applied to increasingly complex defect geometries. To overcome these limitations a elastic Finite Element (FE) method has been developed to simulate pulse-echo inspections of embedded planar defects. The FE model comprises a significantly reduced spatial domain allowing for a Monte-Carlo based approach to consider multiple realisations of defect orientation and surface roughness. The results confirm that defects aligned perpendicular to the path of beam propagation attenuate ultrasonic signals according to the level of surface roughness. However, for defects orientated away from this plane, surface roughness can increase the magnitude of the scattered component propagating back along the path of the incident beam. This study therefore highlights instances where defect roughness increases the magnitude of ultrasonic scattered signals, as opposed to attenuation which is more often assumed.

X-ray simulation for structural integrity for aerospace components - A case study

Science.gov (United States)

Singh, Surendra; Gray, Joseph

2016-02-01

The use of Integrated Computational Materials Engineering (ICME) has rapidly evolved from an emerging technology to the industry standards in Materials, Manufacturing, Chemical, Civil, and Aerospace engineering. Despite this the recognition of the ICME merits has been somewhat lacking within NDE community. This is due in part to the makeup of NDE practitioners. They are a very diverse but regimented group. More than 80% of NDE experts are trained and certified as NDT Level 3's and auditors in order to perform their daily inspection jobs. These jobs involve detection of attribute of interest, which may be a defect or condition or both, in a material. These jobs are performed in strict compliance with procedures that have been developed over many years by trial-and-error with minimal understanding of the underlying physics and interplay between the NDE methods setup parameters. It is not in the nature of these trained Level 3's experts to look for alternate or out-of-the box, solutions. Instead, they follow the procedures for compliance as required by regulatory agencies. This approach is time-consuming, subjective, and is treated as a bottleneck in today's manufacturing environments. As such, there is a need for new NDE tools that provide rapid, high quality solutions for studying structural and dimensional integrity in parts at a reduced cost. NDE simulations offer such options by a shortening NDE technique development-time, attaining a new level in the scientific understanding of physics of interactions between interrogating energy and materials, and reducing costs. In this paper, we apply NDE simulation (XRSIM as an example) for simulating X-Ray techniques for studying aerospace components. These results show that NDE simulations help: 1) significantly shorten NDE technique development-time, 2) assist in training NDE experts, by facilitating the understanding of the underlying physics, and 3) improve both capability and reliability of NDE methods in terms of

Risk assessment techniques for civil aviation security

Energy Technology Data Exchange (ETDEWEB)

Tamasi, Galileo, E-mail: g.tamasi@enac.rupa.i [Ente Nazionale per l' Aviazione Civile-Direzione Progetti, Studi e Ricerche, Via di Villa Ricotti, 42, 00161 Roma (Italy); Demichela, Micaela, E-mail: micaela.demichela@polito.i [SAfeR-Centro Studi su Sicurezza, Affidabilita e Rischi, Dipartimento di Scienza dei Materiali e Ingegneria Chimica, Politecnico di Torino, Corso Duca degli Abruzzi, 24, 10129 Torino (Italy)

2011-08-15

Following the 9/11 terrorists attacks in New York a strong economical effort was made to improve and adapt aviation security, both in infrastructures as in airplanes. National and international guidelines were promptly developed with the objective of creating a security management system able to supervise the identification of risks and the definition and optimization of control measures. Risk assessment techniques are thus crucial in the above process, since an incorrect risk identification and quantification can strongly affect both the security level as the investments needed to reach it. The paper proposes a set of methodologies to qualitatively and quantitatively assess the risk in the security of civil aviation and the risk assessment process based on the threats, criticality and vulnerabilities concepts, highlighting their correlation in determining the level of risk. RAMS techniques are applied to the airport security system in order to analyze the protection equipment for critical facilities located in air-side, allowing also the estimation of the importance of the security improving measures vs. their effectiveness.

Risk assessment techniques for civil aviation security

International Nuclear Information System (INIS)

Tamasi, Galileo; Demichela, Micaela

2011-01-01

Following the 9/11 terrorists attacks in New York a strong economical effort was made to improve and adapt aviation security, both in infrastructures as in airplanes. National and international guidelines were promptly developed with the objective of creating a security management system able to supervise the identification of risks and the definition and optimization of control measures. Risk assessment techniques are thus crucial in the above process, since an incorrect risk identification and quantification can strongly affect both the security level as the investments needed to reach it. The paper proposes a set of methodologies to qualitatively and quantitatively assess the risk in the security of civil aviation and the risk assessment process based on the threats, criticality and vulnerabilities concepts, highlighting their correlation in determining the level of risk. RAMS techniques are applied to the airport security system in order to analyze the protection equipment for critical facilities located in air-side, allowing also the estimation of the importance of the security improving measures vs. their effectiveness.

BİLGİ YÖNETİMİNDE BİLGİ DÖNÜŞTÜRME VE SECI MODELİ : HİZMET SEKTÖRÜNDE BİR ALAN ARAŞTIRMASI

OpenAIRE

Zaim, Halil; Seçgin, Gökhan

2012-01-01

Bu çalışmanın temel amacı, bir bilgi dönüştürme modeli olan SECI Modelinin açıklanması ve modeli oluşturan dört alt boyutun bilgi yönetimi performansı üzerindeki etkisini ortaya koymaktır. Bu çalışma kapsamında gerçekleştirilen araştırma, hizmet sektöründe faaliyet gösteren sekiz farklı firmada çalışanlar arasından seçilen örneklem ile gerçekleştirilmiştir. Bu araştırma kapsamında SECI Modeli'nin alt boyutlarını ve çalışanların bilgi yönetimi performans algılarını ölçen iki fark...

Specificity and sensitivity assessment of selected nasal provocation testing techniques

Directory of Open Access Journals (Sweden)

Edyta Krzych-Fałta

2016-12-01

Full Text Available Introduction: Nasal provocation testing involves an allergen-specific local reaction of the nasal mucosa to the administered allergen. Aim: To determine the most objective nasal occlusion assessment technique that could be used in nasal provocation testing. Material and methods : A total of 60 subjects, including 30 patients diagnosed with allergy to common environmental allergens and 30 healthy subjects were enrolled into the study. The method used in the study was a nasal provocation test with an allergen, with a standard dose of a control solution and an allergen (5,000 SBU/ml administered using a calibrated atomizer into both nostrils at room temperature. Early-phase nasal mucosa response in the early phase of the allergic reaction was assessed via acoustic rhinometry, optical rhinometry, nitric oxide in nasal air, and tryptase levels in the nasal lavage fluid. Results : In estimating the homogeneity of the average values, the Levene’s test was used and receiver operating characteristic curves were plotted for all the methods used for assessing the nasal provocation test with an allergen. Statistically significant results were defined for p < 0.05. Of all the objective assessment techniques, the most sensitive and characteristic ones were the optical rhinometry techniques (specificity = 1, sensitivity = 1, AUC = 1, PPV = 1, NPV = 1. Conclusions : The techniques used showed significant differences between the group of patients with allergic rhinitis and the control group. Of all the objective assessment techniques, those most sensitive and characteristic were the optical rhinometry.

Coping with uncertainty in environmental impact assessments: Open techniques

Energy Technology Data Exchange (ETDEWEB)

Cardenas, Ibsen C., E-mail: c.cardenas@utwente.nl [IceBridge Research Institutea, Universiteit Twente, P.O. Box 217, 7500 AE Enschede (Netherlands); Halman, Johannes I.M., E-mail: J.I.M.Halman@utwente.nl [Universiteit Twente, P.O. Box 217, 7500 AE Enschede (Netherlands)

2016-09-15

Uncertainty is virtually unavoidable in environmental impact assessments (EIAs). From the literature related to treating and managing uncertainty, we have identified specific techniques for coping with uncertainty in EIAs. Here, we have focused on basic steps in the decision-making process that take place within an EIA setting. More specifically, we have identified uncertainties involved in each decision-making step and discussed the extent to which these can be treated and managed in the context of an activity or project that may have environmental impacts. To further demonstrate the relevance of the techniques identified, we have examined the extent to which the EIA guidelines currently used in Colombia consider and provide guidance on managing the uncertainty involved in these assessments. Some points that should be considered in order to provide greater robustness in impact assessments in Colombia have been identified. These include the management of stakeholder values, the systematic generation of project options, and their associated impacts as well as the associated management actions, and the evaluation of uncertainties and assumptions. We believe that the relevant and specific techniques reported here can be a reference for future evaluations of other EIA guidelines in different countries. - Highlights: • uncertainty is unavoidable in environmental impact assessments, EIAs; • we have identified some open techniques to EIAs for treating and managing uncertainty in these assessments; • points for improvement that should be considered in order to provide greater robustness in EIAs in Colombia have been identified; • the paper provides substantiated a reference for possible examinations of EIAs guidelines in other countries.

Coping with uncertainty in environmental impact assessments: Open techniques

International Nuclear Information System (INIS)

Cardenas, Ibsen C.; Halman, Johannes I.M.

2016-01-01

Uncertainty is virtually unavoidable in environmental impact assessments (EIAs). From the literature related to treating and managing uncertainty, we have identified specific techniques for coping with uncertainty in EIAs. Here, we have focused on basic steps in the decision-making process that take place within an EIA setting. More specifically, we have identified uncertainties involved in each decision-making step and discussed the extent to which these can be treated and managed in the context of an activity or project that may have environmental impacts. To further demonstrate the relevance of the techniques identified, we have examined the extent to which the EIA guidelines currently used in Colombia consider and provide guidance on managing the uncertainty involved in these assessments. Some points that should be considered in order to provide greater robustness in impact assessments in Colombia have been identified. These include the management of stakeholder values, the systematic generation of project options, and their associated impacts as well as the associated management actions, and the evaluation of uncertainties and assumptions. We believe that the relevant and specific techniques reported here can be a reference for future evaluations of other EIA guidelines in different countries. - Highlights: • uncertainty is unavoidable in environmental impact assessments, EIAs; • we have identified some open techniques to EIAs for treating and managing uncertainty in these assessments; • points for improvement that should be considered in order to provide greater robustness in EIAs in Colombia have been identified; • the paper provides substantiated a reference for possible examinations of EIAs guidelines in other countries.

Operation of the EPRI nondestructive evaluation center: 1985 annual report

International Nuclear Information System (INIS)

Nemzek, T.A.; Stone, R.M.; Ammirato, F.V.; Becker, F.L.; Krzywosz, K.; Pherigo, G.L.; Wilson, G.H. III.

1986-08-01

This report describes the Electric Power Research Institute (EPRI) Nuclear Division funded nondestructive evaluation (NDE) project activities carried out at the EPRI NDE Center in 1985. The continuing objective of the Center is transfer of research and development results funded by EPRI and other related projects to useful field application. This is being accomplished by qualification and refinement of equipment and techniques, training under realistic conditions, and encouragement of greater involvement of the academic community in NDE education. Significant assistance has been provided to the nuclear utility industry under this project in the form of improved, field-ready equipment and procedures; critically needed assessments of inspection method capability; demonstrations of effectiveness of examination methods; rapid response for critical, short-term problems; and training for specific utility industry needs. This effort has specifically addressed steam generator, piping, steam turbine, and heavy section inspection problems

PERAKENDECİLİK SEKTÖRÜNDE DİNAMİK FİYATLANDIRMA: GENİŞ BİR LİTERATÜR TARAMASI-DYNAMIC PRICING IN RETAILING INDUSTRY: A WIDE LITERATURE SURVEY

Directory of Open Access Journals (Sweden)

Murat Taha BİLİŞİK

2012-07-01

Full Text Available Bu çalışmada, perakendecilik sektöründe dinamik fiyatlandırma uygulamaları ve bu konuda yapılmış geçmiş çalışmaları kapsayan geniş bir literatür taraması ele alınmıştır. Çünkü, günümüz gelişen rekabet koşullarında taleplerin hızla değiştiği gibi fiyatlandırma politikalarının da değişkenlik göstermesi gerektiği saptanmıştır. Bu bağlamda, perakendecilik sektöründe dinamik fiyatlandırma ile ilgili literatürde yer alan çalışmalarda kullanılan yöntemler detaylı bir biçimde incelenmiş ve çeşitli özelliklerine göre sınıflandırmaya tabi tutulmuştur. Sonuç kısmında ise; literatürdeki çalışmalarda rastlanan eksikliklere ve gelecek çalışmalar için fiyat optimizasyonu hesaplamalarında göz önüne alınması gereken durumlara değinilmiştir.- In this study, dynamic pricing applications in retailing and past publications in the literature about this subject have been taken into consideration. The crucial factor making us involved in this study is both the rapid change in demand structures and also the pricing policies over time. By this mean, mathematical solution techniques in the literature used to solve dynamic pricing problems in retailing industry have been analyzed deeply and categorized according to different specialties. In the last section, lacks of mathematical solution techniques and important attributes to be taken into computations have been proposed in order to make better and more accurate price optimizations in future studies.

Chapter 8: Acoustic Assessment of Wood Quality in Trees and Logs

Science.gov (United States)

Xiping Wang; Peter Carter

2015-01-01

Assessing the quality of raw wood materials has become a crucial issue in the operational value chain as forestry and the wood processing industry are increasingly under economic pressure to maximize extracted value. A significant effort has been devoted toward developing robust nondestructive evaluation (NDE) technologies capable of predicting the intrinsic wood...

Assessment of Crack Detection in Heavy-Walled Cast Stainless Steel Piping Welds Using Advanced Low-Frequency Ultrasonic Methods

Energy Technology Data Exchange (ETDEWEB)

Anderson, Michael T.; Crawford, Susan L.; Cumblidge, Stephen E.; Denslow, Kayte M.; Diaz, Aaron A.; Doctor, Steven R.

2007-03-01

Studies conducted at the Pacific Northwest National Laboratory in Richland, Washington, have focused on assessing the effectiveness and reliability of novel approaches to nondestructive examination (NDE) for inspecting coarse-grained, cast stainless steel reactor components. The primary objective of this work is to provide information to the U.S. Nuclear Regulatory Commission on the effectiveness and reliability of advanced NDE methods as related to the inservice inspection of safety-related components in pressurized water reactors (PWRs). This report provides progress, recent developments, and results from an assessment of low frequency ultrasonic testing (UT) for detection of inside surface-breaking cracks in cast stainless steel reactor piping weldments as applied from the outside surface of the components. Vintage centrifugally cast stainless steel piping segments were examined to assess the capability of low-frequency UT to adequately penetrate challenging microstructures and determine acoustic propagation limitations or conditions that may interfere with reliable flaw detection. In addition, welded specimens containing mechanical and thermal fatigue cracks were examined. The specimens were fabricated using vintage centrifugally cast and statically cast stainless steel materials, which are typical of configurations installed in PWR primary coolant circuits. Ultrasonic studies on the vintage centrifugally cast stainless steel piping segments were conducted with a 400-kHz synthetic aperture focusing technique and phased array technology applied at 500 kHz, 750 kHz, and 1.0 MHz. Flaw detection and characterization on the welded specimens was performed with the phased array method operating at the frequencies stated above. This report documents the methodologies used and provides results from laboratory studies to assess baseline material noise, crack detection, and length-sizing capability for low-frequency UT in cast stainless steel piping.

Unusual capabilities and new programs

International Nuclear Information System (INIS)

Janney, D.H.

1981-01-01

A multipurpose NDE laboratory develops many techniques for special purposes. Without an intentional effort to relate these techniques to problems of the nuclear weapons community we pass by opportunities for valuable interchanges. Several solutions to weapons problems are described. Out of these descriptions better NDE techniques will emerge for use in examination of weapons and weapon components

Analytical nondestructive evaluation for materials characterization

International Nuclear Information System (INIS)

Raj, Baldev

1993-01-01

Science and technology of nondestructive testing and evaluation has contributed immensely to the safety and productivity of industrial plants. In recent years, nondestructive evaluation (NDE) has emerged as a frontline research area of equal if not greater technological relevance, for materials characterization as well. A comprehensive range of techniques from qualitative nondestructive testing for quality control of engineering products and materials to quantitative NDE for materials characterization is being used by the engineering industry and materials researchers, for better understanding of the manufacturing practices and materials behaviour. Quantitative NDE is considered essential for ensuring fitness for purpose at the start of the life in case the component has been designed using fracture mechanics parameters. Quantitative NDE is also vital for assessing degradation of material during service. Moreover, quantitative NDE enables characterization of dynamics of certain phenomenon (not achievable by destructive test methodologies) leading to better understanding of the performance of materials in relation to unavoidable defects in the materials. As the next logical step, the need for an analytical approach to NDE is felt. The need and motivation for such an approach is addressed and the means to achieve this objective are identified. It is argued that analytical NDE is essential to meet the challenges of characterization, intelligent processing of materials and life prediction of components and plants. These requirements are of significant importance in the context of recent developments in materials engineering, and for enhancing the competitive advantage of Indian engineering industry in the international market. (author). 9 refs., 3 figs

Classroom Assessment Techniques

Science.gov (United States)

Narayanan, M.

2003-12-01

and the learner should be carefully observed and monitored. Forrest says that Student Portfolios, which document learning in more detail, seldom reveal how teaching contributes to students' progress. Cerbin further indicates that a course portfolio is essentially, a like a manuscript of scholarly work in progress. In this example, it is a work that explains what, how, and why students learn or do not learn in a course. In this paper, the author reports on a dozen techniques that could perhaps be used to document assessment of student learning. References : Cerbin, W. (1993). Fostering a culture of teaching as scholarship. The Teaching Professor, 7(3), 1-2. Edgerton, R., Hutchings, P., & Quinlan, P. (1991). The teaching portfolio: Capturing the scholarship in teaching. Washington, DC: American Association for Higher Education. Forrest, A. (1990). Time will tell: Portfolio-assisted assessment of general education. Washington, DC: American Association for Higher Education. Linn, R., Baker, E., & Dunbar, S. (1991). Complex, Performance-based Assessment: Expectations and Validation Criteria. Educational Researcher, 20 (8), 15-21. Narayanan, M. (2003). Assessment in Higher Education: Partnerships in Learning. Paper presented at the 23rd Annual Lilly Conference on College Teaching, Miami University, Oxford, OH. Seldin, P. (1991). The teaching portfolio. Bolton, MA: Anker. Young, C. O., Sr., & Young, L. H. (1999). Assessing Learning in Interactive Courses. Journal on Excellence in College Teaching, 10 (1), 63-76.

Clinton, Diana, ¿dónde se metieron los periódicos serios?

Directory of Open Access Journals (Sweden)

Lic. Francisco Javier Acuña Arias

1999-01-01

Full Text Available Uno dividió toda la vida los periódicos en dos clases: los amarillistas y los demás. Los demás eran los "serios", es decir, los que uno leía. Pero a raíz del reciente escándalo de Bill Clinton y la cobertura de la muerte aparatosa de Diana de Gales, cabe preguntarse dónde se metieron los periódicos serios. Revistas tan circunspectas como Time y diarios tan reposados como The New York Times se lanzaron a ver quién era más estrepitoso. Total, lo de Clinton no pasó de ser un chisme de pasillo agrandado a crisis de estado por circunstancias picantes.

SLIM-MAUD - a computer based technique for human reliability assessment

International Nuclear Information System (INIS)

Embrey, D.E.

1985-01-01

The Success Likelihood Index Methodology (SLIM) is a widely applicable technique which can be used to assess human error probabilities in both proceduralized and cognitive tasks (i.e. those involving decision making, problem solving, etc.). It assumes that expert assessors are able to evaluate the relative importance (or weights) of different factors called Performance Shaping Factors (PSFs), in determining the likelihood of error for the situations being assessed. Typical PSFs are the extent to which good procedures are available, operators are adequately trained, the man-machine interface is well designed, etc. If numerical ratings are made of the PSFs for the specific tasks being evaluated, these can be combined with the weights to give a numerical index, called the Success Likelihood Index (SLI). The SLI represents, in numerical form, the overall assessment of the experts of the likelihood of task success. The SLI can be subsequently transformed to a corresponding human error probability (HEP) estimate. The latest form of the SLIM technique is implemented using a microcomputer based system called MAUD (Multi-Attribute Utility Decomposition), the resulting technique being called SLIM-MAUD. A detailed description of the SLIM-MAUD technique and case studies of applications are available. An illustrative example of the application of SLIM-MAUD in probabilistic risk assessment is given

A review of nondestructive examination technology for polyethylene pipe in nuclear power plant

Science.gov (United States)

Zheng, Jinyang; Zhang, Yue; Hou, Dongsheng; Qin, Yinkang; Guo, Weican; Zhang, Chuck; Shi, Jianfeng

2018-05-01

Polyethylene (PE) pipe, particularly high-density polyethylene (HDPE) pipe, has been successfully utilized to transport cooling water for both non-safety- and safety-related applications in nuclear power plant (NPP). Though ASME Code Case N755, which is the first code case related to NPP HDPE pipe, requires a thorough nondestructive examination (NDE) of HDPE joints. However, no executable regulations presently exist because of the lack of a feasible NDE technique for HDPE pipe in NPP. This work presents a review of current developments in NDE technology for both HDPE pipe in NPP with a diameter of less than 400 mm and that of a larger size. For the former category, phased array ultrasonic technique is proven effective for inspecting typical defects in HDPE pipe, and is thus used in Chinese national standards GB/T 29460 and GB/T 29461. A defect-recognition technique is developed based on pattern recognition, and a safety assessment principle is summarized from the database of destructive testing. On the other hand, recent research and practical studies reveal that in current ultrasonic-inspection technology, the absence of effective ultrasonic inspection for large size was lack of consideration of the viscoelasticity effect of PE on acoustic wave propagation in current ultrasonic inspection technology. Furthermore, main technical problems were analyzed in the paper to achieve an effective ultrasonic test method in accordance to the safety and efficiency requirements of related regulations and standards. Finally, the development trend and challenges of NDE test technology for HDPE in NPP are discussed.

Development of Metallic Sensory Alloys

Science.gov (United States)

Wallace Terryl A.; Newman, John A.; Horne, Michael R.; Messick, Peter L.

2010-01-01

Existing nondestructive evaluation (NDE) technologies are inherently limited by the physical response of the structural material being inspected and are therefore not generally effective at the identification of small discontinuities, making the detection of incipient damage extremely difficult. One innovative solution to this problem is to enhance or complement the NDE signature of structural materials to dramatically improve the ability of existing NDE tools to detect damage. To address this need, a multifunctional metallic material has been developed that can be used in structural applications. The material is processed to contain second phase sensory particles that significantly improve the NDE response, enhancing the ability of conventional NDE techniques to detect incipient damage both during and after flight. Ferromagnetic shape-memory alloys (FSMAs) are an ideal material for these sensory particles as they undergo a uniform and repeatable change in both magnetic properties and crystallographic structure (martensitic transformation) when subjected to strain and/or temperature changes which can be detected using conventional NDE techniques. In this study, the use of a ferromagnetic shape memory alloy (FSMA) as the sensory particles was investigated.

Evaluation of examination techniques for ferritic stainless steel feedwater heater tubing

International Nuclear Information System (INIS)

Nugent, M.J.; Catapano, M.C.

1995-01-01

Ferritic stainless steel has been finding increased application in utility plant feedwater heaters due to good strength and corrosion resistance and absence of potential copper contamination of feedwater system. Ferritic stainless steel is highly magnetic and is generally not inspectable using conventional eddy current testing techniques. A variety of techniques have been developed for inspection of this tubing material used in typical heat exchanger applications. Through a project funded by the Empire State Electric Energy Research Corporation (ESEERCO), the evaluation of data generated by four present state of the art NDE testing techniques were evaluated on a controlled mock-up of the heater tubing with service related defects. The primary objective was to determine the strengths and limitations of each method. The testing of two in service feedwater heaters at the Consolidated Edison Company of New York, Inc. (Con Edison's) Arthur Kill Generating Station also allowed further evaluations based on actual field conditions

Risk-assessment techniques and the reactor licensing process

International Nuclear Information System (INIS)

Levine, S.

1979-01-01

A brief description of the Reactor Safety Study (WASH-1400), concentrating on the engineering aspects of the contribution to reactor accident risks is followed by some comments on how we have applied the insights and techniques developed in this study to prepare a program to improve the safety of nuclear power plants. Some new work we are just beginning on the application of risk-assessment techniques to stablize the reactor licensing process is also discussed

Advanced NDE (ANDE) and its application for pressure tube inspections in OPG reactors

Energy Technology Data Exchange (ETDEWEB)

Jarron, D.; Trelinski, M.; Kretz, S. [Ontario Power Generation, Ajax, Ontario (Canada)]. E-mail: don.jarron@opg.com; mike.trelinski@opg.com; steve.kretz@opg.com

2006-07-01

Periodic and in-service inspections of CANDU fuel channels are essential for the proper assessment of the structural integrity of these vital components. The arrival of new delivery devices for fuel channel inspections (Universal Delivery Machine) has driven new methods for gathering and analyzing NDE data. The Advanced Non-Destructive Examination (ANDE) system has been designed and field implemented as a high speed data acquisition system to meet the requirements of the CSA N285.4 code. It was built from the solid foundation of CIGAR experience and uses cutting edge hardware and software to attain high speed data collection enabling relatively quick inspection of a large number of fuel channels. The capabilities of the ANDE inspection system include: Surface and volumetric inspection of pressure tube by ultrasonics; Flaw characterization by ultrasonics; Pressure tube diameter measurements; Pressure tube thickness measurements; Garter Spring location by Eddy Current; Garter Spring location by ultrasonics; Pressure tube sag measurement. In addition to the above, selected flaws/areas of a pressure tube can be replicated using a two plate ANDE replica tool. At the heart of the inspection system is a set of twelve ultrasonic probes positioned in such a way that the inspected areas are examined from various angles and directions and by various ultrasonic wave modes (shear and longitudinal). High frequency ultrasound used for the examinations allows for reliable detection of small flaws. Separate sensors have been installed on the inspection head for Garter Spring location and sag measurements. (author)

Doppler ultrasound imaging techniques for assessment of synovial inflammation

Directory of Open Access Journals (Sweden)

Filippucci E

2013-09-01

Full Text Available Emilio Filippucci,1 Fausto Salaffi,1 Marina Carotti,2 Walter Grassi1 1Rheumatology Department, Polytechnic University of the Marche, Ancona, Italy; 2Department of Radiology, Polytechnic University of the Marche, Ancona, Italy Abstract: Ultrasound is an evolving technique, and the rapid progress made in ultrasound technology over the past ten years has dramatically increased its range of applications in rheumatology. One of the most exciting advances is the use of Doppler ultrasound imaging in the assessment of blood flow abnormalities at the synovial tissue level in patients with chronic inflammatory arthritis. This review describes the Doppler techniques available and their main applications in patients with inflammatory arthritis, discusses the evidence supporting their use, and outlines the latest advances in hardware and software. Spectral, color, and power Doppler allow sensitive assessment of vascular abnormalities at the synovial tissue level. Use of contrast agents enhances visualization of the small synovial vessels using color or power Doppler ultrasound and allows for accurate characterization of the rheumatoid pannus. Doppler techniques represent a unique method for assessment of synovial inflammation, showing blood flow characteristics in real time. They are safe, noninvasive, cost-effective, and have high sensitivity in revealing and monitoring synovitis. However, several questions still need to be answered. In the near future, the Doppler techniques described here, together with upcoming hardware and software facilities, will be investigated further and a consensus will be reached on their feasibility and appropriate use in daily rheumatologic practice. Keywords: power and color Doppler techniques, ultrasound, contrast media, synovitis, rheumatoid arthritis

Application of the actor model to large scale NDE data analysis

Science.gov (United States)

Coughlin, Chris

2018-03-01

The Actor model of concurrent computation discretizes a problem into a series of independent units or actors that interact only through the exchange of messages. Without direct coupling between individual components, an Actor-based system is inherently concurrent and fault-tolerant. These traits lend themselves to so-called "Big Data" applications in which the volume of data to analyze requires a distributed multi-system design. For a practical demonstration of the Actor computational model, a system was developed to assist with the automated analysis of Nondestructive Evaluation (NDE) datasets using the open source Myriad Data Reduction Framework. A machine learning model trained to detect damage in two-dimensional slices of C-Scan data was deployed in a streaming data processing pipeline. To demonstrate the flexibility of the Actor model, the pipeline was deployed on a local system and re-deployed as a distributed system without recompiling, reconfiguring, or restarting the running application.

The Environmental Assessment Technique: An Empirical Study.

Science.gov (United States)

Overall, Jesse U., IV

The purpose of the study was to investigate the effectiveness of Alexander Astin's Environmental Assessment Technique (EAT) in describing the environmental press at a large public university, California State University at Los Angeles. Results indicate that EAT is a very economical method for broadly describing aspects of a university's…

Evaluation and improvement of nondestructive evaluation reliability for inservice inspection of light water reactors

International Nuclear Information System (INIS)

Bates, D.J.; Deffenbaugh, J.D.; Good, M.S.; Heasler, P.G.; Mart, G.A.; Simonen, F.A.; Spanner, J.C.; Taylor, T.T.; Van Fleet, L.G.

1987-01-01

The Evaluation and Improvement of NDE Reliability for Inservice Inspection (ISI) of Light Water Reactors (NDE Reliability) Program at Pacific Northwest Laboratory (PNL) was established to determine the reliability of current ISI techniques and to develop recommendations that will ensure a suitably high inspection reliability. The objectives of this NRC program are to: determine the reliability of ultrasonic ISI performed on commercial light-water reactor (LWR) primary systems, using probabilistic fracture mechanics analysis, determine the impact of NDE unreliability on system safety and determine the level of inspection reliability required to ensure a suitably low failure probability, evaluate the degree of reliability improvement that could be achieved using improved and advanced NDE techniques, based on material properties, service conditions, and NDE uncertainties, recommend revisions to ASME Code, Section XI, and Regulatory Requirements that will ensure suitably low failure probabilities. The scope of this program is limited to ISI of primary systems; the results and recommendations may also be applicable to Class II piping systems

Detecting decay in wood components

Science.gov (United States)

R.J. Ross; X. Wang; B.K. Brashaw

2005-01-01

This chapter presents a summary of the Wood and Timber Condition Assessment Manual. It focuses on current inspection techniques for decay detection and provides guidelines on the use of various non-destructive evaluation (NDE) methods in locating and defining areas of deterioration in timber bridge components and other civil structures.

Application of fisheries management techniques to assessing impacts: task I report

International Nuclear Information System (INIS)

McKenzie, D.H.; Baker, K.S.; Fickeisen, D.H.; Metzger, R.M.; Skalski, J.R.

1979-03-01

Task I efforts examined the available fisheries management techniques and assessed their potential application in a confirmatory monitoring program. The objective of such monitoring programs is to confirm that the prediction of an insignificant impact (usually made in the FES) was correct. Fisheries resource managers have developed several tools for assessing the fish population response to stress (exploitation) and they were thought potentially useful for detecting nuclear power plant impacts. Techniques in three categories were examined; catch removal, population dynamics, and nondestructive censuses, and the report contains their description, examples of application, advantages, and disadvantages. The techniques applied at nuclear power plant sites were examined in detail to provide information on implementation and variability of specific approaches. The most suitable techniques to incorporate into a monitoring program confirming no impact appear to be those based on Catch Per Unity Effort (CPUE) and hydroacoustic data. In some specific cases, age and growth studies and indirect census techniques may be beneficial. Recommendations for task II efforts to incorporate these techniques into monitoring program designs are presented. These include development of guidelines for; (1) designing and implementing a data collection program; (2) interpreting these data and assessing the occurrence of impact, and (3) establishment of the monitoring program's ability to detect changes in the affected populations

Expertise, Domains, and the Consensual Assessment Technique

Science.gov (United States)

Kaufman, James C.; Baer, John; Cole, Jason C.

2009-01-01

The Consensual Assessment Technique (CAT) argues that the most valid judgments of the creativity are those of the combined opinions of experts in the field. Yet who exactly qualifies as an expert to evaluate a creative product such as a short story? This study examines both novice and expert judgments of student short fiction. Results indicate a…

Marktkonstitution und Regulierung der unabhängigen Film- und Fernsehproduktion : Staat, Verbände und Gewerkschaften im deutsch-britischen Vergleich

OpenAIRE

Elbing, Sabine; Voelzkow, Helmut

2006-01-01

"In einem internationalen Vergleich von Deutschland und Großbritannien wird untersucht, welche Beiträge die staatliche Politik und die Wirtschafts- und Sozialpartner (Wirtschafts- und Arbeitgeberverbände sowie Gewerkschaften) zur Förderung der unabhängigen Film- und Fernsehproduktion leisten. Es wird gezeigt, dass die britische Medienpolitik die Position der unabhängigen Film- und Fernsehproduktion gegenüber den Fernsehsendern gestärkt hat. In Deutschland hat die Medienpolitik darauf verzicht...

Acoustic assessment of wood quality of raw forest materials : a path to increased profitability

Science.gov (United States)

Xiping Wang; Peter Carter; Robert J. Ross; Brian K. Brashaw

2007-01-01

Assessment of the quality of raw wood materials has become a crucial issue in the operational value chain as forestry and the wood processing industry are increasingly under economic pressure to maximize extracted value. A significant effort has been devoted toward developing robust nondestructive evaluation (NDE) technologies capable of predicting the intrinsic wood...

Assessment of hand blood flow: a modified technique

International Nuclear Information System (INIS)

Kirsh, J.C.; Tepperman, P.S.

1985-01-01

A blood flow artifact has been identified with the conventional bolus-injection technique in radionuclide studies of hand disorders. The artifact, consisting of increased blood flow on the injected side, was demonstrated in 22 of 25 subjects. Using a modified injection technique to allow time for local blood flow to return to the basal state, the artifact could be eliminated in 19 of 23 additional subjects. Use of this simple protocol should help avoid misinterpretation of blood flow asymmetry in the assessment of hand disorders

The verification tests of residual radioactivity measurement and assessment techniques for buildings and soils

International Nuclear Information System (INIS)

Onozawa, T.; Ishikura, T.; Yoshimura, Yukio; Nakazawa, M.; Makino, S.; Urayama, K.; Kawasaki, S.

1996-01-01

According to the standard procedure for decommissioning a commercial nuclear power plant (CNPP) in Japan, controlled areas will be released for unrestricted use before the dismantling of a reactor building. If manual survey and sampling techniques were applied to measurement for unrestricted release on and in the extensive surface of the building, much time and much specialized labor would be required to assess the appropriateness of the releasing. Therefore the authors selected the following three techniques for demonstrating reliability and applicability of the techniques for CNPPs: (1) technique of assessing radioactive concentration distribution on the surface of buildings (ADB); (2) technique of assessing radioactive permeation distribution in the concrete structure of buildings (APB); (3) technique of assessing radioactive concentration distribution in soil (ADS). These tests include the techniques of measuring and assessing very low radioactive concentration distribution on the extensive surfaces of buildings and the soil surrounding of a plant with automatic devices. Technical investigation and preliminary study of the verification tests were started in 1990. In the study, preconditions were clarified for each technique and the performance requirements were set up. Moreover, simulation models have been constructed for several feasible measurement method to assess their performance in terms of both measurement test and simulation analysis. Fundamental tests have been under way using small-scale apparatuses since 1994

Objective techniques for psychological assessment, phase 2. [techniques for measuring human performance during space flight stress

Science.gov (United States)

Wortz, E. C.; Saur, A. J.; Nowlis, D. P.; Kendall, M. P.

1974-01-01

Results are presented of an initial experiment in a research program designed to develop objective techniques for psychological assessment of individuals and groups participating in long-duration space flights. Specifically examined is the rationale for utilizing measures of attention as an objective assessment technique. Subjects participating in the experiment performed various tasks (eg, playing matrix games which appeared on a display screen along with auditory stimuli). The psychophysiological reactions of the subjects were measured and are given. Previous research of various performance and psychophysiological methods of measuring attention is also discussed. The experiment design (independent and dependent variables) and apparatus (computers and display devices) are described and shown. Conclusions and recommendations are presented.

Risk assessment techniques with applicability in marine engineering

Science.gov (United States)

Rudenko, E.; Panaitescu, F. V.; Panaitescu, M.

2015-11-01

Nowadays risk management is a carefully planned process. The task of risk management is organically woven into the general problem of increasing the efficiency of business. Passive attitude to risk and awareness of its existence are replaced by active management techniques. Risk assessment is one of the most important stages of risk management, since for risk management it is necessary first to analyze and evaluate risk. There are many definitions of this notion but in general case risk assessment refers to the systematic process of identifying the factors and types of risk and their quantitative assessment, i.e. risk analysis methodology combines mutually complementary quantitative and qualitative approaches. Purpose of the work: In this paper we will consider as risk assessment technique Fault Tree analysis (FTA). The objectives are: understand purpose of FTA, understand and apply rules of Boolean algebra, analyse a simple system using FTA, FTA advantages and disadvantages. Research and methodology: The main purpose is to help identify potential causes of system failures before the failures actually occur. We can evaluate the probability of the Top event.The steps of this analize are: the system's examination from Top to Down, the use of symbols to represent events, the use of mathematical tools for critical areas, the use of Fault tree logic diagrams to identify the cause of the Top event. Results: In the finally of study it will be obtained: critical areas, Fault tree logical diagrams and the probability of the Top event. These results can be used for the risk assessment analyses.

Processing and Probability Analysis of Pulsed Terahertz NDE of Corrosion under Shuttle Tile Data

Science.gov (United States)

Anastasi, Robert F.; Madaras, Eric I.; Seebo, Jeffrey P.; Ely, Thomas M.

2009-01-01

This paper examines data processing and probability analysis of pulsed terahertz NDE scans of corrosion defects under a Shuttle tile. Pulsed terahertz data collected from an aluminum plate with fabricated corrosion defects and covered with a Shuttle tile is presented. The corrosion defects imaged were fabricated by electrochemically etching areas of various diameter and depth in the plate. In this work, the aluminum plate echo signal is located in the terahertz time-of-flight data and a threshold is applied to produce a binary image of sample features. Feature location and area are examined and identified as corrosion through comparison with the known defect layout. The results are tabulated with hit, miss, or false call information for a probability of detection analysis that is used to identify an optimal processing threshold.

Review of progress in quantitative nondestructive evaluation. Volume 8A and Volume 8B

International Nuclear Information System (INIS)

Thompson, D.O.; Chimenti, D.E.

1989-01-01

Volume 8 contains the edited papers presented at the 1988 Review of Progress in Quantitative Nondestructive Evaluation meeting. The 288 papers discuss such topics as fundamental techniques as acoustic testing, eddy current testing, and x-ray radiography; advanced techniques using x-ray computed tomography and laser ultrasonics; interpretive signal and image processing using expert systems and adaptive analysis; NDE probes and sensors and NDE systems and instrumentation; materials process control and inspection reliability including human factors. Materials discussed range from electronic circuit materials, coatings, adhesive bonds, smart structures, composite materials, welded joints, ferrous materials, and steels and alloys. Stress, texture, structural and fracture properties of materials are characterized using various NDE techniques. Applications to reactor, aircraft, and space vehicle components are investigated

Miniaturized hand held microwave interference scanning system for NDE of dielectric armor and armor systems

International Nuclear Information System (INIS)

Schmidt, Karl F.; Little, Jack R.; Ellingson, William A.; Meitzler, Thomas J.; Green, William

2011-01-01

Inspection of ceramic-based armor has advanced through development of a microwave-based, portable, non-contact NDE system. Recently, this system was miniaturized and made wireless for maximum utility in field applications. The electronic components and functionality of the laboratory system are retained, with alternative means of position input for creation of scan images. Validation of the detection capability was recently demonstrated using specially fabricated surrogates and ballistic impact-damaged specimens. The microwave data results have been compared to data from laboratory-based microwave interferometry systems and digital x-ray imaging. The microwave interference scanning has been shown to reliably detect cracks, laminar features and material property variations. The authors present details of the system operation, descriptions of the test samples used and recent results obtained.

Photogrammetric analysis of concrete specimens and structures for condition assessment

Science.gov (United States)

D'Amico, Nicolas; Yu, Tzuyang

2016-04-01

Deterioration of civil infrastructure in America demands routine inspection and maintenance to avoid catastrophic failures from occurring. Among many other non-destructive evaluations (NDE), photogrammetry is an accessible and realistic approach used for non-destructive evaluation (NDE) of a civil infrastructure systems. The objective of this paper is to explore the capabilities of photogrammetry for locating, sizing, and analyzing the remaining capacity of a specimen or system using point cloud data. Geometric interpretations, composed from up to 70 photographs are analyzed as a mesh or point cloud models. In this case study, concrete, which exhibits a large amount of surface texture features, was thoroughly examined. These evaluative techniques discussed were applied to concrete cylinder models as well as portions of civil infrastructure including buildings, retaining walls, and bridge abutments. In this paper, the aim is to demonstrate the basic analytical functionality of photogrammetry, as well as its applicability to in-situ civil infrastructure systems. In concrete specimens defect length and location can be evaluated in a fully defined model (one with the maximum amount of correctly acquired photographs) with less than 2% error. Error was found to be inversely proportional to the number of acceptable photographs acquired, remaining significantly under 10% error for any model with enough data to render. Furthermore, volumetric stress evaluations were applied using a cross sectional evaluation technique to locate the critical area, and determine the severity of damages. Finally, findings and the accuracy of the results are discussed.

Assessment of attention and different feedback techniques on ...

African Journals Online (AJOL)

Assessment of attention and different feedback techniques on psychomotor skill learninb and retention. JO Adeogun, IA Oyewuni. Abstract. No Abstract. Full Text: EMAIL FULL TEXT EMAIL FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT · http://dx.doi.org/10.4314/ajpherd.v11i4.46288 · AJOL African ...

Combining heuristic and statistical techniques in landslide hazard assessments

Science.gov (United States)

Cepeda, Jose; Schwendtner, Barbara; Quan, Byron; Nadim, Farrokh; Diaz, Manuel; Molina, Giovanni

2014-05-01

As a contribution to the Global Assessment Report 2013 - GAR2013, coordinated by the United Nations International Strategy for Disaster Reduction - UNISDR, a drill-down exercise for landslide hazard assessment was carried out by entering the results of both heuristic and statistical techniques into a new but simple combination rule. The data available for this evaluation included landslide inventories, both historical and event-based. In addition to the application of a heuristic method used in the previous editions of GAR, the availability of inventories motivated the use of statistical methods. The heuristic technique is largely based on the Mora & Vahrson method, which estimates hazard as the product of susceptibility and triggering factors, where classes are weighted based on expert judgment and experience. Two statistical methods were also applied: the landslide index method, which estimates weights of the classes for the susceptibility and triggering factors based on the evidence provided by the density of landslides in each class of the factors; and the weights of evidence method, which extends the previous technique to include both positive and negative evidence of landslide occurrence in the estimation of weights for the classes. One key aspect during the hazard evaluation was the decision on the methodology to be chosen for the final assessment. Instead of opting for a single methodology, it was decided to combine the results of the three implemented techniques using a combination rule based on a normalization of the results of each method. The hazard evaluation was performed for both earthquake- and rainfall-induced landslides. The country chosen for the drill-down exercise was El Salvador. The results indicate that highest hazard levels are concentrated along the central volcanic chain and at the centre of the northern mountains.

Safety assessment of cast steel valve housing using NDE- and FM-methods

Energy Technology Data Exchange (ETDEWEB)

Blauel, J G; Hodulak, L [Fraunhofer-Institut fuer Werkstoffmechanik, Freiburg im Breisgau (Germany)

1988-12-31

This document presents some results concerning the safety assessment of cast steel valve housing. This risk assessment is performed through the Non Destructive Examination and Fracture Mechanics methods. (TEC).

Integration of nondestructive examination reliability and fracture mechanics

International Nuclear Information System (INIS)

Doctor, S.R.; Bates, D.J.; Charlot, L.A.

1985-01-01

The primary pressure boundaries (pressure vessels and piping) of nuclear power plants are in-service inspected (ISI) according to the rules of ASME Boiler and Pressure Vessel Code, Section XI. Ultrasonic techniques are normally used for these inspections, which are periodically performed on a sampling of welds. The Integration of Nondestructive Examination (NDE) Reliability and Fracture Mechanics (FM) Program at Pacific Northwest Laboratory was established to determine the reliability of current ISI techniques and to develop recommendations that will ensure a suitably high inspection reliability. The objectives of this NRC program are to: 1) determine the reliability of ultrasonic ISI performed on commercial light-water reactor primary systems; 2) using probabilistic FM analysis, determine the impact of NDE unreliability on system safety and determine the level of inspection reliability required to ensure a suitably low failure probability; 3) evaluate the degree of reliability improvement that could be achieved using improved and advanced NDE techniques; and 4) based on material properties, service conditions, and NDE uncertainties, formulate recommended revisions to ASME Code, Section XI, and Regulatory Requirements needed to ensure suitably low failure probabilities

Application of Isotope Techniques for Assessing Nutrient Dynamics in River Basins

International Nuclear Information System (INIS)

2013-05-01

Nutrients are necessary for the growth and survival of animals, plants and other organisms. However, industrial, agricultural and urban development has dramatically increased nutrient levels in river systems, including nitrogen and phosphorus containing substances, degrading water quality, causing acidification and eutrophication and affecting aquatic ecosystems. Nutrient assessment and management in river systems has been an important part of water resource management for the past few decades, but the provision of appropriate and effective nutrient assessment and management continues to be a challenge for water resource managers and policy makers. Difficulties in assessment and management are due in part to the fact that nutrients in rivers may originate from a variety of sources, take numerous pathways and transform into other substances. This publication presents the application of isotope techniques as a powerful tool for evaluating the sources, pathways, transformation, and fate of nutrients in river systems, focusing on nitrogen, phosphorus and carbon containing substances. Eleven researchers using various isotope techniques for different aspects of nutrient studies and two IAEA officers met in a technical meeting and discussed a publication that could assist water resource managers in dealing with nutrient assessment and management issues in river systems. These researchers also recognized the need for careful consideration in selecting appropriate isotope techniques in view of not only technical, but also financial, human resources and logistical capabilities, among others. These contributors are listed as major authors in the later pages of this document. This publication aims at serving water resource managers as a guidebook on the application of isotope techniques in nutrient assessment and management, but it is also expected to be of practical aid for other interested and concerned individuals and organization.

Application of Isotope Techniques for Assessing Nutrient Dynamics in River Basins

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-05-15

Nutrients are necessary for the growth and survival of animals, plants and other organisms. However, industrial, agricultural and urban development has dramatically increased nutrient levels in river systems, including nitrogen and phosphorus containing substances, degrading water quality, causing acidification and eutrophication and affecting aquatic ecosystems. Nutrient assessment and management in river systems has been an important part of water resource management for the past few decades, but the provision of appropriate and effective nutrient assessment and management continues to be a challenge for water resource managers and policy makers. Difficulties in assessment and management are due in part to the fact that nutrients in rivers may originate from a variety of sources, take numerous pathways and transform into other substances. This publication presents the application of isotope techniques as a powerful tool for evaluating the sources, pathways, transformation, and fate of nutrients in river systems, focusing on nitrogen, phosphorus and carbon containing substances. Eleven researchers using various isotope techniques for different aspects of nutrient studies and two IAEA officers met in a technical meeting and discussed a publication that could assist water resource managers in dealing with nutrient assessment and management issues in river systems. These researchers also recognized the need for careful consideration in selecting appropriate isotope techniques in view of not only technical, but also financial, human resources and logistical capabilities, among others. These contributors are listed as major authors in the later pages of this document. This publication aims at serving water resource managers as a guidebook on the application of isotope techniques in nutrient assessment and management, but it is also expected to be of practical aid for other interested and concerned individuals and organization.

Assessment of heterogeneous geological environment using geostatistical techniques

International Nuclear Information System (INIS)

Toida, Masaru; Suyama, Yasuhiro; Shiogama, Yukihiro; Atsumi, Hiroyuki; Abe, Yasunori; Furuichi, Mitsuaki

2003-02-01

'Geoscientific' research at Tono are developing site investigation and assessment techniques in geological environment. One of their important themes is to establish rational methodology to reduce uncertainties associated with the understanding of geological environment, which often exhibits significant heterogeneity. Purpose of this study is to identify and evaluate uncertainties associated with the understanding of geological environment. Because it is useful to guide designing effective site investigation techniques to reduce the uncertainty. For this, a methodology of the uncertainty analysis concerning the heterogeneous geological environment has been developed. In this report the methodology has also been tested through an exercise attempted in Tono area to demonstrate its applicability. This report summarizes as follows: 1) The exercise shows that the methodology considered 'variability' and 'ignorance' can demonstrate its applicability at three-dimensional case. 2) The exercise shows that the methodology can identity and evaluate uncertainties concerning ground water flow associated with performance assessment. 3) Based on sensitivity analyses, it is possible for the methodology to support designs of the following stage investigations to reduce the uncertainties efficiently. (author)

[Research progress and development trend of quantitative assessment techniques for urban thermal environment.

Science.gov (United States)

Sun, Tie Gang; Xiao, Rong Bo; Cai, Yun Nan; Wang, Yao Wu; Wu, Chang Guang

2016-08-01

Quantitative assessment of urban thermal environment has become a focus for urban climate and environmental science since the concept of urban heat island has been proposed. With the continual development of space information and computer simulation technology, substantial progresses have been made on quantitative assessment techniques and methods of urban thermal environment. The quantitative assessment techniques have been developed to dynamics simulation and forecast of thermal environment at various scales based on statistical analysis of thermal environment on urban-scale using the historical data of weather stations. This study reviewed the development progress of ground meteorological observation, thermal infrared remote sensing and numerical simulation. Moreover, the potential advantages and disadvantages, applicability and the development trends of these techniques were also summarized, aiming to add fundamental knowledge of understanding the urban thermal environment assessment and optimization.

NDE during precision manufacturing of pressure components in nuclear reactors

International Nuclear Information System (INIS)

Raj, Baldev; Venkataram, B.; Chellapandi, P.

2010-01-01

Energy is the critical enabler for all social and economic developments and growth of civilization. For a nation to be energy secure, it should have a balanced and healthy energy basket with a varied mix of energy sources in right proportions depending on the resources of the country. It is now a well realized fact that nuclear energy is an inevitable option that should be present in energy basket of nuclear mature countries. This is due the fact that nuclear power has proved to be (a) capable of generating electricity safely on a large-scale with price stability over long periods of time satisfying a modern economy's significant demand for electricity that must be available round-the-clock; and (b) it is environmentally benign and provides a clean energy source with minimum of green house gas emissions. Internationally, about I 696 electricity is derived from nuclear power. In the Indian context, the contribution from nuclear power currently is about 3%, which needs to be enhanced by 4 fold by 2030 and 10 fold by 2050 if India is to sustain its current gross domestic product. NDE intertwined with materials, manufacturing technology and total life cycle management are crucial to safe and economic nuclear power.

Rotordynamic Analysis and Feasibility Study of a Disk Spin Test Facility for Rotor Health Monitoring

Science.gov (United States)

Sawicki, Jerzy T.

2005-01-01

Recently, National Aeronautics and Space Administration (NASA) initiated a program to achieve the significant improvement in aviation safety. One of the technical challenges is the design and development of accelerated experiments that mimic critical damage cases encountered in engine components. The Nondestructive Evaluation (NDE) Group at the NASA Glenn Research Center (GRC) is currently addressing the goal concerning propulsion health management and the development of propulsion system specific technologies intended to detect potential failures prior to catastrophe. For this goal the unique disk spin simulation system was assembled at NASA GRC, which allows testing of rotors with the spinning speeds up to 10K RPM, and at the elevated temperature environment reaching 540 C (1000 F). It is anticipated that the facility can be employed for detection of Low Cycle Fatigue disk cracking and further High Cycle Fatigue blade vibration. The controlled crack growth studies at room and elevated temperatures can be conducted on the turbine wheels, and various NDE techniques can be integrated and assessed as in-situ damage monitoring tools. Critical rotating parts in advanced gas turbine engines such as turbine disks frequently operate at high temperature and stress for long periods of time. The integrity of these parts must be proven by non-destructive evaluation (NDE) during various machining steps ranging from forging blank to finished shape, and also during the systematic overhaul inspections. Conventional NDE methods, however, have unacceptable limits. Some of these techniques are time-consuming and inconvenient for service aircraft testing. Almost all of these techniques require that the vicinity of the damage is known in advance. These experimental techniques can provide only local information and no indication of the structural strength at a component and/or system level. The shortcomings of currently available NDE methods lead to the requirement of new damage

Coping with uncertainty in environmental impact assessments: Open techniques

NARCIS (Netherlands)

Chivatá Cárdenas, Ibsen; Halman, Johannes I.M.

2016-01-01

Uncertainty is virtually unavoidable in environmental impact assessments (EIAs). From the literature related to treating and managing uncertainty, we have identified specific techniques for coping with uncertainty in EIAs. Here, we have focused on basic steps in the decision-making process that take

Acoustic Techniques for Structural Health Monitoring

Science.gov (United States)

Frankenstein, B.; Augustin, J.; Hentschel, D.; Schubert, F.; Köhler, B.; Meyendorf, N.

2008-02-01

Future safety and maintenance strategies for industrial components and vehicles are based on combinations of monitoring systems that are permanently attached to or embedded in the structure, and periodic inspections. The latter belongs to conventional nondestructive evaluation (NDE) and can be enhanced or partially replaced by structural health monitoring systems. However, the main benefit of this technology for the future will consist of systems that can be differently designed based on improved safety philosophies, including continuous monitoring. This approach will increase the efficiency of inspection procedures at reduced inspection times. The Fraunhofer IZFP Dresden Branch has developed network nodes, miniaturized transmitter and receiver systems for active and passive acoustical techniques and sensor systems that can be attached to or embedded into components or structures. These systems have been used to demonstrate intelligent sensor networks for the monitoring of aerospace structures, railway systems, wind energy generators, piping system and other components. Material discontinuities and flaws have been detected and monitored during full scale fatigue testing. This paper will discuss opportunities and future trends in nondestructive evaluation and health monitoring based on new sensor principles and advanced microelectronics. It will outline various application examples of monitoring systems based on acoustic techniques and will indicate further needs for research and development.

Techniques for Liquid Rocket Combustion Spontaneous Stability and Rough Combustion Assessments

Science.gov (United States)

Kenny, R. J.; Giacomoni, C.; Casiano, M. J.; Fischbach, S. R.

2016-01-01

This work presents techniques for liquid rocket engine combustion stability assessments with respect to spontaneous stability and rough combustion. Techniques covering empirical parameter extraction, which were established in prior works, are applied for three additional programs: the F-1 Gas Generator (F1GG) component test program, the RS-84 preburner component test program, and the Marshall Integrated Test Rig (MITR) program. Stability assessment parameters from these programs are compared against prior established spontaneous stability metrics and updates are identified. Also, a procedure for comparing measured with predicted mode shapes is presented, based on an extension of the Modal Assurance Criterion (MAC).

Applications of field portable computers to NDE of nuclear power plant steam turbine/generator rotors, discs, and retaining rings

International Nuclear Information System (INIS)

Reinhart, E.R.; Leon-Salamanca, T.

2004-01-01

The new generation of compact, powerful portable computers have been incorporated into a number of nondestructive evaluation (NDE) systems used to inspect critical areas of the steam turbine and generator units of nuclear power plants. Due to the complex geometry of turbine rotors, generator rotors, retaining rings, and shrunk-on turbine discs, the computers are needed to rapidly calculate the optimum position of an ultrasonic transducer or eddy current probe in order to detect defects at several critical areas. Examples where computers have been used to overcome problems in nondestructive evaluation include; analysis of large numbers of closely spaced near-bore ultrasonic reflectors to determine their potential for link-up in turbine and generator rotor bores, distinguishing ultrasonic crack signals from other reflectors such as the shrink-fit form reflector detected during ultrasonic scanning of shrunk-on generator retaining rings, and detection and recording of eddy current and ultrasonic signals from defects that could be missed by data acquisition systems with inadequate response. The computers are also used to control scanners to insure total inspection coverage. To facilitate the use of data from detected discontinuities in conjunction with stress and fracture mechanics analysis programs, the computers provide presentations of flaws in color and in three dimensions. The field computers have been instrumental in allowing the inspectors to develop on-site reports that enable the owner/operator to rapidly make run/repair/replace decisions. Examples of recent experiences using field portable computers in NDE systems will be presented along with anticipated future developments. (author)

Classification Technique for Ultrasonic Weld Inspection Signals using a Neural Network based on 2-dimensional fourier Transform and Principle Component Analysis

International Nuclear Information System (INIS)

Kim, Jae Joon

2004-01-01

Neural network-based signal classification systems are increasingly used in the analysis of large volumes of data obtained in NDE applications. Ultrasonic inspection methods on the other hand are commonly used in the nondestructive evaluation of welds to detect flaws. An important characteristic of ultrasonic inspection is the ability to identify the type of discontinuity that gives rise to a peculiar signal. Standard techniques rely on differences in individual A-scans to classify the signals. This paper proposes an ultrasonic signal classification technique based on the information tying in the neighboring signals. The approach is based on a 2-dimensional Fourier transform and the principal component analysis to generate a reduced dimensional feature vector for classification. Results of applying the technique to data obtained from the inspection of actual steel welds are presented

Las aplicaciones interactivas multimedia en España: ¿hacia dónde evoluciona el mercado?

Directory of Open Access Journals (Sweden)

Lic. Nati Ramajo Hernández

1998-01-01

Full Text Available El despegue del sector multimedia en nuestro país (entendiendo como tal las aplicaciones interactivas multimedia ha sido espectacular en los últimos tiempos. El número de títulos publicados en CD-ROM, al igual que el número de productores, ha aumentado considerablemente. Pero, ¿cómo es esa nueva industria?, ¿qué productos ofrece?, ¿hacia dónde evoluciona el mercado? El presente trabajo pretende hacer un repaso a la breve historia de las aplicaciones interactivas multimedia en España hasta llegar al momento actual, analizando por el camino la tipología de los productos y concluyendo con los nuevos formatos que están cambiando el mercado.

NDE Conference on Civil Engineering : a joint conference of the 7th Structural Materials Technology Conference (SMT) and the 6th International Symposium on Nondestructive Testing in Civil Engineering (NDT-CE)

Science.gov (United States)

2007-01-01

The 2006 NDE conference on Civil Engineering was held in St. Louis, MO on August 14 18, 2006. The conference combined the 7th Structural Materials Technology Conference (SMT) along with the 6th International Symposium on Nondestructive Testing in...

An Assessment of Nondestructive Evaluation Capability for Complex Additive Manufacturing Aerospace Components

Science.gov (United States)

Walker, James; Beshears, Ron; Lambert, Dennis; Tilson, William

2016-01-01

The primary focus of this work is to investigate some of the fundamental relationships between processing, mechanical testing, materials characterization, and NDE for additively manufactured (AM) components using the powder bed fusion direct melt laser sintered process. The goal is to understand the criticality of defects unique to the AM process and then how conventional nondestructive evaluation methods as well as some of the more non-traditional methods such as computed tomography, are effected by the AM material. Specific defects including cracking, porosity and partially/unfused powder will be addressed. Besides line-of-site NDE, as appropriate these inspection capabilities will be put into the context of complex AM geometries where hidden features obscure, or inhibit traditional NDE methods.

A novel optical investigation technique for railroad track inspection and assessment

Science.gov (United States)

Sabato, Alessandro; Beale, Christopher H.; Niezrecki, Christopher

2017-04-01

Track failures due to cross tie degradation or loss in ballast support may result in a number of problems ranging from simple service interruptions to derailments. Structural Health Monitoring (SHM) of railway track is important for safety reasons and to reduce downtime and maintenance costs. For this reason, novel and cost-effective track inspection technologies for assessing tracks' health are currently insufficient and needed. Advancements achieved in recent years in cameras technology, optical sensors, and image-processing algorithms have made machine vision, Structure from Motion (SfM), and three-dimensional (3D) Digital Image Correlation (DIC) systems extremely appealing techniques for extracting structural deformations and geometry profiles. Therefore, optically based, non-contact measurement techniques may be used for assessing surface defects, rail and tie deflection profiles, and ballast condition. In this study, the design of two camera-based measurement systems is proposed for crossties-ballast condition assessment and track examination purposes. The first one consists of four pairs of cameras installed on the underside of a rail car to detect the induced deformation and displacement on the whole length of the track's cross tie using 3D DIC measurement techniques. The second consists of another set of cameras using SfM techniques for obtaining a 3D rendering of the infrastructure from a series of two-dimensional (2D) images to evaluate the state of the track qualitatively. The feasibility of the proposed optical systems is evaluated through extensive laboratory tests, demonstrating their ability to measure parameters of interest (e.g. crosstie's full-field displacement, vertical deflection, shape, etc.) for assessment and SHM of railroad track.

ASSESSMENT OF CABLE AGING USING CONDITION MONITORING TECHNIQUES

International Nuclear Information System (INIS)

GROVE, E.; LOFARO, R.; SOO, P.; VILLARAN, M.; HSU, F.

2000-01-01

Electric cables in nuclear power plants suffer degradation during service as a result of the thermal and radiation environments in which they are installed. Instrumentation and control cables are one type of cable that provide an important role in reactor safety. Should the polymeric cable insulation material become embrittled and cracked during service, or during a loss-of-coolant-accident (LOCA) and when steam and high radiation conditions are anticipated, failure could occur and prevent the cables from fulfilling their intended safety function(s). A research program is being conducted at Brookhaven National Laboratory to evaluate condition monitoring (CM) techniques for estimating the amount of cable degradation experienced during in-plant service. The objectives of this program are to assess the ability of the cables to perform under a simulated LOCA without losing their ability to function effectively, and to identify CM techniques which may be used to determine the effective lifetime of cables. The cable insulation materials tested include ethylene propylene rubber (EPR) and cross-linked polyethylene (XLPE). Accelerated aging (thermal and radiation) to the equivalent of 40 years of service was performed, followed by exposure to simulated LOCA conditions. The effectiveness of chemical, electrical, and mechanical condition monitoring techniques are being evaluated. Results indicate that several of these methods can detect changes in material parameters with increasing age. However, each has its limitations, and a combination of methods may provide an effective means for trending cable degradation in order to assess the remaining life of cables

Fiber Bragg Gratings, IT Techniques and Strain Gauge Validation for Strain Calculation on Aged Metal Specimens

Directory of Open Access Journals (Sweden)

Ander Montero

2011-01-01

Full Text Available This paper studies the feasibility of calculating strains in aged F114 steel specimens with Fiber Bragg Grating (FBG sensors and infrared thermography (IT techniques. Two specimens have been conditioned under extreme temperature and relative humidity conditions making comparative tests of stress before and after aging using different adhesives. Moreover, a comparison has been made with IT techniques and conventional methods for calculating stresses in F114 steel. Implementation of Structural Health Monitoring techniques on real aircraft during their life cycle requires a study of the behaviour of FBG sensors and their wiring under real conditions, before using them for a long time. To simulate aging, specimens were stored in a climate chamber at 70 °C and 90% RH for 60 days. This study is framed within the Structural Health Monitoring (SHM and Non Destructuve Evaluation (NDE research lines, integrated into the avionics area maintained by the Aeronautical Technologies Centre (CTA and the University of the Basque Country (UPV/EHU.

Assessing a new gene expression analysis technique for radiation biodosimetry applications

Energy Technology Data Exchange (ETDEWEB)

Manning, Grainne; Kabacik, Sylwia; Finnon, Paul; Paillier, Francois; Bouffler, Simon [Cancer Genetics and Cytogenetics, Biological Effects Department, Centre for Radiation, Chemical and Environmental Hazards, Health Protection Agency, Chilton, Didcot, Oxfordshire OX11 ORQ (United Kingdom); Badie, Christophe, E-mail: christophe.badie@hpa.org.uk [Cancer Genetics and Cytogenetics, Biological Effects Department, Centre for Radiation, Chemical and Environmental Hazards, Health Protection Agency, Chilton, Didcot, Oxfordshire OX11 ORQ (United Kingdom)

2011-09-15

The response to any radiation accident or incident involving actual or potential ionising radiation exposure requires accurate and rapid assessment of the doses received by individuals. The techniques available today for biodosimetry purposes are not fully adapted to rapid high-throughput measurements of exposures in large numbers of individuals. A recently emerging technique is based on gene expression analysis, as there are a number of genes which are radiation responsive in a dose-dependent manner. The present work aimed to assess a new technique which allows the detection of the level of expression of up to 800 genes without need of enzymatic reactions. In order to do so, human peripheral blood was exposed ex vivo to a range of x-ray doses from 5 mGy to 4 Gy of x-rays and the transcriptional expression of five radiation-responsive genes PHPT1, PUMA, CCNG1, DDB2 and MDM2 was studied by both the nCounter Digital Analyzer and Multiplex Quantitative Real-Time Polymerase Chain Reaction (MQRT-PCR) as the benchmark technology. Results from both techniques showed good correlation for all genes with R{sup 2} values ranging between 0.8160 and 0.9754. The reproducibility of the nCounter Digital Analyzer was also assessed in independent biological replicates and proved to be good. Although the slopes of the correlation of results obtained by the techniques suggest that MQRT-PCR is more sensitive than the nCounter Digital Analyzer, the nCounter Digital Analyzer provides sensitive and reliable data on modifications in gene expression in human blood exposed to radiation without enzymatic amplification of RNA prior to analysis.

Evaluation of Ultrasonic and Thermal Nondestructive Evaluation for the Characterization of Aging Degradation in Braided Composite Materials

Science.gov (United States)

Martin, Richard E.

2010-01-01

This paper examines the ability of traditional nondestructive evaluation (NDE) techniques to measure the degradation of braided polymer composite materials subjected to thermal-humidity cycling to simulate aging. A series of braided composite coupons were examined using immersion ultrasonic and pulsed thermography techniques in the as received condition. These same specimens were then examined following extended thermal-humidity cycling. Results of this examination did not show a significant change in the resulting (NDE) signals.

Radiographic testing at Lawrence Livermore National Laboratory

International Nuclear Information System (INIS)

Bossi, R.H.

1982-01-01

Radiographic testing is a nondestructive inspection technique which uses penetrating radiation. The Nondestructive Evaluation (NDE) Section at Lawrence Livermore National Laboratory has a broad spectrum of equipment and techniques for radiographic testing. These resources include low-energy vacuum systems, low- and mid-energy cabinet and cell radiographic systems, high-energy linear accelerators, portable x-ray machines and radioisotopes for radiographic inspections. For diagnostic testing the NDE Section also has real-time and flash radiographic equipment

Advanced Marketing Core Curriculum. Test Items and Assessment Techniques.

Science.gov (United States)

Smith, Clifton L.; And Others

This document contains duties and tasks, multiple-choice test items, and other assessment techniques for Missouri's advanced marketing core curriculum. The core curriculum begins with a list of 13 suggested textbook resources. Next, nine duties with their associated tasks are given. Under each task appears one or more citations to appropriate…

Assessment of Effective Prestressed Force of Nuclear Containment Building using SI Technique

Energy Technology Data Exchange (ETDEWEB)

Lee, H. P.; Jang, J. B.; Hwang, K. M.; Song, Y. C. [Korea Electric Power Research Institute, Daejeon (Korea, Republic of)

2010-10-15

Bonded tendons have been used in reactor buildings of heavy water reactors and the light water reactors of some nuclear power plants operating in Korea. The assessment of prestressed forces on those bonded tendons is becoming an important issue in assuring their continuous operation beyond their design life. In order to assess the effective prestressed force on the bonded tendon, indirect assessment techniques have been applying to the test beams which were manufactured on construction time. Therefore, this research mainly forced to establish the assessment methodology to measure directly the effective prestressed force on the bonded tendon of containment buildings using System Identification (SI) technique. To accomplish this purpose, simple SI method was proposed and adapted three dimensional finite element analysis of the 1:4 scale prestressed concrete containment vessel (PCCV) tested by Sandia National Laboratory in 2000

Assessment of biological leaf tissue using biospeckle laser imaging technique

Science.gov (United States)

Ansari, M. Z.; Mujeeb, A.; Nirala, A. K.

2018-06-01

We report on the application of an optical imaging technique, the biospeckle laser, as a potential tool to assess biological and medicinal plant leaves. The biospeckle laser technique is a non-invasive and non-destructive optical technique used to investigate biological objects. Just after their removal from plants, the torn leaves were used for biospeckle laser imaging. Quantitative evaluation of the biospeckle data using the inertia moment (IM) of the time history speckle pattern, showed that the IM can be utilized to provide a biospeckle signature to the plant leaves. It showed that leaves from different plants can have their own characteristic IM values. We further investigated the infected regions of the leaves that display a relatively lower biospeckle activity than the healthy tissue. It was easy to discriminate between the infected and healthy regions of the leaf tissue. The biospeckle technique can successfully be implemented as a potential tool for the taxonomy of quality leaves. Furthermore, the technique can help boost the quality of ayurvedic medicines.

Boat sampling technique for assessment of ageing of components

International Nuclear Information System (INIS)

Kumar, Kundan; Shyam, T.V.; Kayal, J.N.; Rupani, B.B.

2006-01-01

Boat sampling technique (BST) is a surface sampling technique, which has been developed for obtaining, in-situ, metal samples from the surface of an operating component without affecting its operating service life. The BST is non-destructive in nature and the sample is obtained without plastic deformation or without thermal degradation of the parent material. The shape and size of the sample depends upon the shape of the cutter and the surface geometry of the parent material. Miniature test specimens are generated from the sample and the specimens are subjected to various tests, viz. Metallurgical Evaluation, Metallographic Evaluation, Micro-hardness Evaluation, sensitisation test, small punch test etc. to confirm the integrity and assessment of safe operating life of the component. This paper highlights design objective of boat sampling technique, description of sampling module, sampling cutter and its performance evaluation, cutting process, boat samples, operational sequence of sampling module, qualification of sampling module, qualification of sampling technique, qualification of scooped region of the parent material, sample retrieval system, inspection, testing and examination to be carried out on the boat samples and scooped region. (author)

Interest and limitations of projective techniques in the assessment of personality disorders.

Science.gov (United States)

Petot, J M

2000-06-01

Assessing personality disorders (PD) remains a difficult task because of persistent problems linked to concurrent validity of existing instruments, which are all structured interviews or self-report inventories. It has been advocated that indirect methods, projective techniques in particular, can strengthen PD assessment methods. The thematic apperception test (TAT) may be a significant adjuvant method of PD assessment.

Use of Formative Classroom Assessment Techniques in a Project Management Course

Science.gov (United States)

Purcell, Bernice M.

2014-01-01

Formative assessment is considered to be an evaluation technique that informs the instructor of the level of student learning, giving evidence when it may be necessary for the instructor to make a change in delivery based upon the results. Several theories of formative assessment exist, all which propound the importance of feedback to the student.…

Air Quality Assessment Using Interpolation Technique

Directory of Open Access Journals (Sweden)

Awkash Kumar

2016-07-01

Full Text Available Air pollution is increasing rapidly in almost all cities around the world due to increase in population. Mumbai city in India is one of the mega cities where air quality is deteriorating at a very rapid rate. Air quality monitoring stations have been installed in the city to regulate air pollution control strategies to reduce the air pollution level. In this paper, air quality assessment has been carried out over the sample region using interpolation techniques. The technique Inverse Distance Weighting (IDW of Geographical Information System (GIS has been used to perform interpolation with the help of concentration data on air quality at three locations of Mumbai for the year 2008. The classification was done for the spatial and temporal variation in air quality levels for Mumbai region. The seasonal and annual variations of air quality levels for SO2, NOx and SPM (Suspended Particulate Matter have been focused in this study. Results show that SPM concentration always exceeded the permissible limit of National Ambient Air Quality Standard. Also, seasonal trends of pollutant SPM was low in monsoon due rain fall. The finding of this study will help to formulate control strategies for rational management of air pollution and can be used for many other regions.

Assessing Dental Hygienists' Communication Techniques for Use with Low Oral Health Literacy Patients.

Science.gov (United States)

Flynn, Priscilla; Acharya, Amit; Schwei, Kelsey; VanWormer, Jeffrey; Skrzypcak, Kaitlyn

2016-06-01

This primary aim of this study was to assess communication techniques used with low oral health literacy patients by dental hygienists in rural Wisconsin dental clinics. A secondary aim was to determine the utility of the survey instrument used in this study. A mixed methods study consisting of a cross-sectional survey, immediately followed by focus groups, was conducted among dental hygienists in the Marshfield Clinic (Wisconsin) service area. The survey quantified the routine use of 18 communication techniques previously shown to be effective with low oral health literacy patients. Linear regression was used to analyze the association between routine use of each communication technique and several indicator variables, including geographic practice region, oral health literacy familiarity, communication skills training and demographic indicators. Qualitative analyses included code mapping to the 18 communication techniques identified in the survey, and generating new codes based on discussion content. On average, the 38 study participants routinely used 6.3 communication techniques. Dental hygienists who used an oral health literacy assessment tool reported using significantly more communication techniques compared to those who did not use an oral health literacy assessment tool. Focus group results differed from survey responses as few dental hygienists stated familiarity with the term "oral health literacy." Motivational interviewing techniques and using an integrated electronic medical-dental record were additional communication techniques identified as useful with low oral health literacy patients. Dental hygienists in this study routinely used approximately one-third of the communication techniques recommended for low oral health literacy patients supporting the need for training on this topic. Based on focus group results, the survey used in this study warrants modification and psychometric testing prior to further use. Copyright © 2016 The American Dental

Durability Analysis and Experimental Validation of Environmental Barrier Coating (EBC Performance Using Combined Digital Image Correlation and NDE

Directory of Open Access Journals (Sweden)

Ali Abdul-Aziz

2016-12-01

Full Text Available To understand the failure mechanism or to predict the spallation life of environmental barrier coatings (EBC on fiber reinforced ceramic matrix composites, the fracture strength of EBC and the process of the crack growth in EBC layers need to be experimentally determined under standard or simulated engine operating conditions. The current work considers a multi layered barium strontium aluminum silicate (BSAS-based EBC-coated, melt infiltrated silicon carbide fiber reinforced silicon carbide matrix composite (MI SiC/SiC specimen that was tensile tested at room temperature. Numerous tests were performed under tensile loading conditions, and the specimen was loaded until failure under pre-determined stress levels. The specimen was examined with optical microscopy, scanning electron microscopy (SEM, computed tomography (CT scan, and digital image correlation (DIC camera. Observation from the computed tomography scanning, the SEM, and the optical microscopy did not offer conclusive information concerning the cracks that spawned during the tests. However, inspection with the DIC camera offered some indication that cracks had developed and allowed their detection and the location of their initiation site. Thus, this study provides detailed discussion of the results obtained from the experimental investigation and the nondestructive evaluation (NDE, and it also includes assessment of the stress response predicted by analytical modeling and their impact on EBC durability and crack growth formation under complex loading settings.

Final Assessment of Manual Ultrasonic Examinations Applied to Detect Flaws in Primary System Dissimilar Metal Welds at North Anna Power Station

Energy Technology Data Exchange (ETDEWEB)

Anderson, Michael T.; Diaz, Aaron A.; Cinson, Anthony D.; Crawford, Susan L.; Prowant, Matthew S.; Doctor, Steven R.

2014-03-24

PNNL conducted a technical assessment of the NDE issues and protocols that led to missed detections of several axially oriented flaws in a steam generator primary inlet dissimilar metal weld at North Anna Power Station, Unit 1 (NAPS-1). This particular component design exhibits a significant outside-diameter (OD) taper that is not included as a blind performance demonstration mock-up within the industry’s Performance Demonstration Initiative, administered by EPRI. For this reason, the licensee engaged EPRI to assist in the development of a technical justification to support the basis for a site-specific qualification. The service-induced flaws at NAPS-1 were eventually detected as a result of OD surface machining in preparation for a full structural weld overlay. The machining operation uncovered the existence of two through-wall flaws, based on the observance of primary water leaking from the dissimilar metal weld. A total of five axially oriented flaws were detected in varied locations around the weld circumference. The field volumetric examination that was conducted at NAPS-1 was a non-encoded, real-time manual ultrasonic examination. PNNL conducted both an initial assessment, and subsequently, a more rigorous technical evaluation (reported here), which has identified an array of NDE issues that may have led to the subject missed detections. These evaluations were performed through technical reviews and discussions with NRC staff, EPRI NDE Center personnel, industry and ISI vendor personnel, and ultrasonic transducer manufacturers, and laboratory tests, to better understand the underlying issues at North Anna.

Heuristic Enhancement of Magneto-Optical Images for NDE

Science.gov (United States)

Cacciola, Matteo; Megali, Giuseppe; Pellicanò, Diego; Calcagno, Salvatore; Versaci, Mario; Morabito, FrancescoCarlo

2010-12-01

The quality of measurements in nondestructive testing and evaluation plays a key role in assessing the reliability of different inspection techniques. Each different technique, like the magneto-optic imaging here treated, is affected by some special types of noise which are related to the specific device used for their acquisition. Therefore, the design of even more accurate image processing is often required by relevant applications, for instance, in implementing integrated solutions for flaw detection and characterization. The aim of this paper is to propose a preprocessing procedure based on independent component analysis (ICA) to ease the detection of rivets and/or flaws in the specimens under test. A comparison of the proposed approach with some other advanced image processing methodologies used for denoising magneto-optic images (MOIs) is carried out, in order to show advantages and weakness of ICA in improving the accuracy and performance of the rivets/flaw detection.

25 years of NDE in fabrication of zirconium alloy mill products and nuclear fuel in the Nuclear Fuel Complex

International Nuclear Information System (INIS)

Mistry, R.K.; Laxminarayana, B.; Srivastava, R.K.

1996-01-01

Failure of nuclear fuel is highly undesirable from both economic and operational aspects. Hence all the components require rigorous QC and inspection checks. NDT plays a major role in assuring the quality of the products both at final and intermediate stages. This paper gives an overall review of NDT methods employed in achieving the integrity of nuclear products. The NDE procedures followed in NFC are visual inspection, radiography, penetrant testing, eddy current testing, ultrasonic testing and helium leak testing. NFC's quality assurance programme is organised to achieve the desired objectives by carrying out in process and final inspection at all critical steps of fabrication. (author)

Material property relationships for pipeline steels and the potential for application of NDE

Science.gov (United States)

Smart, Lucinda; Bond, Leonard J.

2016-02-01

The oil and gas industry in the USA has an extensive infrastructure of pipelines, 70% of which were installed prior to 1980, and almost half were installed during the 1950s and 1960s. Ideally the mechanical properties (i.e. yield strength, tensile strength, transition temperature, and fracture toughness) of a steel pipe must be known in order to respond to detected defects in an appropriate manner. Neither current in-ditch methods nor the ILI inspection data have yet determined and map the desired mechanical properties with adequate confidence. In the quest to obtain the mechanical properties of a steel pipe using a nondestructive method, it is important to understand that there are many inter-related variables. This paper reports a literature review and an analysis of a sample set of data. There is promise for correlating the results of NDE measurement modalities to the information required to develop relationships between those measurements and the mechanical measurements desired for pipelines to ensure proper response to defects which are of significant threat.

Reliability and criterion validity of an observation protocol for working technique assessments in cash register work.

Science.gov (United States)

Palm, Peter; Josephson, Malin; Mathiassen, Svend Erik; Kjellberg, Katarina

2016-06-01

We evaluated the intra- and inter-observer reliability and criterion validity of an observation protocol, developed in an iterative process involving practicing ergonomists, for assessment of working technique during cash register work for the purpose of preventing upper extremity symptoms. Two ergonomists independently assessed 17 15-min videos of cash register work on two occasions each, as a basis for examining reliability. Criterion validity was assessed by comparing these assessments with meticulous video-based analyses by researchers. Intra-observer reliability was acceptable (i.e. proportional agreement >0.7 and kappa >0.4) for 10/10 questions. Inter-observer reliability was acceptable for only 3/10 questions. An acceptable inter-observer reliability combined with an acceptable criterion validity was obtained only for one working technique aspect, 'Quality of movements'. Thus, major elements of the cashiers' working technique could not be assessed with an acceptable accuracy from short periods of observations by one observer, such as often desired by practitioners. Practitioner Summary: We examined an observation protocol for assessing working technique in cash register work. It was feasible in use, but inter-observer reliability and criterion validity were generally not acceptable when working technique aspects were assessed from short periods of work. We recommend the protocol to be used for educational purposes only.

Nondestructive evaluation of oriented strand board exposed to decay fungi.

Science.gov (United States)

Barbara L. Illman; Vina W. Yang; Robert J. Ross; William J. Nelson

2002-01-01

Stress wave nondestructive evaluation (NDE) technologies are being used in our laboratory to evaluate the performance properties of engineered wood. These techniques have proven useful in the inspection of timber structures to locate internal voids and decayed or deteriorated areas in large timbers. But no information exists concerning NDE and important properties of...

Real-time radiography, digital radiography, and computed tomography for nonintrusive waste drum characterization

International Nuclear Information System (INIS)

Martz, H.E.; Schneberk, D.J.; Roberson, G.P.

1994-07-01

We are investigating and developing the application of x-ray nondestructive evaluation (NDE) and gamma-ray nondestructive assay (NDA) methods to nonintrusively characterize 208-liter (55-gallon) mixed waste drums. Mixed wastes contain both hazardous and radioactive materials. We are investigating the use of x-ray NDE methods to verify the content of documented waste drums and determine if they can be used to identify hazardous and nonconforming materials. These NDE methods are also being used to help waste certification and hazardous waste management personnel at LLNL to verify/confirm and/or determine the contents of waste. The gamma-ray NDA method is used to identify the intrinsic radioactive source(s) and to accurately quantify its strength. The NDA method may also be able to identify some hazardous materials such as heavy metals. Also, we are exploring techniques to combine both NDE and NDA data sets to yield the maximum information from these nonintrusive, waste-drum characterization methods. In this paper, we report an our x-ray NDE R ampersand D activities, while our gamma-ray NDA activities are reported elsewhere in the proceedings. We have developed a data, acquisition scanner for x-ray NDE real-time radiography (RTR), as well as digital radiography transmission computed tomography (TCT) along with associated computational techniques for image reconstruction, analysis, and display. We are using this scanner and real-waste drums at Lawrence Livermore National Laboratory (LLNL). In this paper, we discuss some issues associated with x-ray imaging, describe the design construction of an inexpensive NDE drum scanner, provide representative DR and TCT results of both mock- and real-waste drums, and end with a summary of our efforts and future directions. The results of these scans reveal that RTR, DR, and CT imaging techniques can be used in concert to provide valuable information about the interior of low-level-, transuranic-, and mock-waste drums without

Slurry steam generator program and baseline eddy current examination

International Nuclear Information System (INIS)

Clark, R.A.; Doctor, P.G.

1985-01-01

The Steam Generator Group Project was initiated in January 1982 with formation of consortium including NRC, EPRI, Japanese, French, and Italian participants. The project utilizes a retired-from-service nuclear steam generator established in a specially designed facility which houses the unit in its normal vertical operating position. The most important objectives deal with validation of nondestructive examination (NDE) techniques used to characterize steam generators during service. This research generator offers the first opportunity to characterize a statistically significant number of service-induced defects nondestructively followed by destructive metallographic confirmation. The project seeks to establish the reliability of defect detection and the accuracy of sizing defects via current state-of-the-art NDE. Other service degraded tubes will be burst tested to establish remaining service integrity. The integrity information and NDE reliability results will serve as inputs to establish a model for steam generator in-service inspections, and provide a data base for evaluation of tube plugging criteria. In addition to NDE validation goals, the project will use the service degraded generator as a specimen for demonstration/proof testing of repair and maintenance techniques, including chemical cleaning/decontamination technologies. In addition to the efforts associated with NDE, a multitude of other project tasks have continued through 1984, and results are presented

Surry steam generator program and baseline eddy current examination

International Nuclear Information System (INIS)

Clark, R.A.; Doctor, P.G.

1985-01-01

The Steam Generator Group Project was initiated in January 1982 with formation of consortium including NRC, EPRI, Japanese, French, and Italian participants. The project utilizes a retired-from-service nuclear steam generator established in a specially designed facility which houses the unit in its normal vertical operating position. The most important objectives deal with validation of nondestructive examination (NDE) techniques used to characterize steam generators during service. This research generator offers the first opportunity to characterize a statistically significant number of service-induced defects nondestructively followed by destructive metallographic confirmation. The project seeks to establish the reliability of defect detection and the accuracy of sizing defects via current state-of-the-art NDE. Other service degraded tubes will be burst tested to establish remaining service integrity. The integrity information and NDE reliability results will serve as inputs to establish a model for steam generator in-service inspections, and provide a data base for evaluation of tube plugging criteria. In addition to NDE validation goals, the project will use the service degraded generator as a specimen for demonstration/proof testing of repair and maintenance techniques, including chemical cleaning/decontamination technologies. In addition to the efforts associated with NDE, a multitude of other project tasks have continued through 1984, and results are presented

Advanced structural integrity assessment procedures. Working material

International Nuclear Information System (INIS)

1994-01-01

The purpose of the meeting was to provide an international forum for discussion on recent results in research and utility practice in the field of methodology for the structural integrity assessment of components including relevant non-codified procedures. The scope of the meeting included deterministic and probabilistic approaches. The papers covered the following topics: Leak-before-break concepts; non-destructive examination (NDE) and surveillance results; statistical evaluation of non-destructive examination data; pressurized thermal shock evaluation; fatigue effects (including vibration); and verification qualification. The meeting was attended by 32 specialists from 8 countries. Refs, figs and tabs

A new scintigraphic technique for assessment of right atrial function

International Nuclear Information System (INIS)

Marmor, A.; Biello, D.R.; Sampathkumaran, K.S.; Geltman, E.M.; Siegel, B.A.; Roberts, R.

1981-01-01

Gated radionuclide imaging with 99 mTc-labeled red blood cells was employed to assess changes in right atrial (RA) volume in 17 subjects. Studies were repeated within two hours in five of 12 normal subjects and at two and ten days after infarction in five patients. Time-activity curves were generated for the RA and right ventricle (RV) from variable regions of interest defined by automatic edge detection. The RA time-activity curve exhibited four phases: filling, early emptying, equilibration, and late emptying. Repeated measurements of RA early emptying rates correlated closely in normals (r . 0.93). Early RA emptying and RV filling rates corresponded closely (r . 0.89). In four patients with infarction, the RA emptying rate was slowed on the first study but had normalized by 10 days. In a patient with inferior infarction and suspected RV infarction, the RA emptying rate was depressed and remained so for 10 days. Thus, relative changes in right atrial volume can be assessed reproducibly by a radionuclide technique, which is relatively independent of geometric assumptions. This technique offers great promise as a method to assess atrial function in health and disease

Choice and complexation of techniques and tools for assessment of NPP I and C systems safety

International Nuclear Information System (INIS)

Illiashenko, Oleg; Babeshko, Eugene

2011-01-01

There are a lot of techniques to analyze and assess reliability and safety of NPP Instrumentation and Control (I and C) systems (e.g. FMEA - Failure Modes and Effects Analysis and its modifications, FTA - Fault Tree Analysis, HAZOP - Hazard and Operability Analysis, RBD - Reliability Block Diagram, Markov Models, etc.) and quantity of tools based on these techniques is constantly increasing. Known ways of safety assessment, as well as problems of their choice and complexation are analyzed. Objective of the paper is the development of general 'technique of techniques choosing' and tool for support of such technique. The following criteria are used for analysis and comparison and their features are described: compliance to normative documents; experience of application in industry; methods used for assessment of system NPP I and C safety; tool architecture/framework; reporting; vendor support, etc. Comparative analysis results of existing T and T - Tools and Techniques for safety analysis are presented in matrix form ('Tools-Criterion') with example. Features of complexation of different safety assessment techniques (FMECA, FTA, RBD, Markov Models) are described. The proposed technique is implemented as special tool for decision-making. The proposed technique was used for development of RPC Radiy company standard CS 66. This guide contains requirements and procedures of FMECA analysis of developed and produced NPP I and C systems based on RADIY platform. (author)

Development of the Italian Version of the Near-Death Experience Scale

Directory of Open Access Journals (Sweden)

Francesca Pistoia

2018-02-01

Full Text Available Near-death experiences (NDEs have been defined as any conscious perceptual experience occurring in individuals pronounced clinically dead or who came very close to physical death. They are frequently reported by patients surviving a critical injury and, intriguingly, they show common features across different populations. The tool traditionally used to assess NDEs is the NDE Scale, which is available in the original English version. The aim of this study was to develop the Italian version of the NDE Scale and to assess its reliability in a specific clinical setting. A process of translation of the original scale was performed in different stages in order to obtain a fully comprehensible and accurate Italian translation. Later, the scale was administered to a convenience sample of patients who had experienced a condition of coma and were, at the time of assessment, fully conscious and able to provide information as requested by the scale. Inter-rater and test–retest reliability, assessed by the weighted Cohen’s kappa (Kw, were estimated. A convenience sample of 20 subjects [mean age ± standard deviation (SD 51.6 ± 17.1, median time from injury 3.5 months, interquartile range (IQR 2–10] was included in the study. Inter-rater [Kw 0.77 (95% CI 0.67–0.87] and test–retest reliability [Kw 0.96 (95% CI 0.91–1.00] showed good to excellent values for the total scores of the Italian NDE Scale and for subanalyses of each single cluster of the scale. An Italian Version of the NDE Scale is now available to investigate the frequency of NDE, the causes for NDE heterogeneity across different life-threatening conditions, and the possible neural mechanisms underlying NDE phenomenology.

Performance and non-destructive evaluation methods of airborne radome and stealth structures

Science.gov (United States)

Panwar, Ravi; Ryul Lee, Jung

2018-06-01

In the past few years, great effort has been devoted to the fabrication of highly efficient, broadband radome and stealth (R&S) structures for distinct control, guidance, surveillance and communication applications for airborne platforms. The evaluation of non-planar aircraft R&S structures in terms of their electromagnetic performance and structural damage is still a very challenging task. In this article, distinct measurement techniques are discussed for the electromagnetic performance and non-destructive evaluation (NDE) of R&S structures. This paper deals with an overview of the transmission line method and free space measurement based microwave measurement techniques for the electromagnetic performance evaluation of R&S structures. In addition, various conventional as well as advanced methods, such as millimetre and terahertz wave based imaging techniques with great potential for NDE of load bearing R&S structures, are also discussed in detail. A glimpse of in situ NDE techniques with corresponding experimental setup for R&S structures is also presented. The basic concepts, measurement ranges and their instrumentation, measurement method of different R&S structures and some miscellaneous topics are discussed in detail. Some of the challenges and issues pertaining to the measurement of curved R&S structures are also presented. This study also lists various mathematical models and analytical techniques for the electromagnetic performance evaluation and NDE of R&S structures. The research directions described in this study may be of interest to the scientific community in the aerospace sectors.

Interdisciplinary seminar on nondestructive testing and fracture mechanics. Lectures

International Nuclear Information System (INIS)

1998-01-01

The proceedings volume contains 17 lectures presented at a DGZfP seminar held in Berlin/Germany, 2-3 November 1998. Fracture mechanics data are of interest with respect to determining maximum permissible limits for non-destructive materials evaluation, and as quantitative NDE test results indicating existing materials flaws in a system component, delivering information for assessement of remaining service life and safety risks. The topics of lectures are: Quality concepts for welded joints; NDE for service life assessment of engine components, shown for evaluation of engine pales and disks; NDE and crack detection at pressurized gas cylinders; fracture mechanics requirements for NDE in nuclear installations, discussion of practical examples (T. Seidenkranz); failure of off-shore constructions seen in the light of a novel fracture mechanics technical code. (orig./CB) [de

Reliability Assessment of Wind Farm Electrical System Based on a Probability Transfer Technique

Directory of Open Access Journals (Sweden)

Hejun Yang

2018-03-01

Full Text Available The electrical system of a wind farm has a significant influence on the wind farm reliability and electrical energy yield. The disconnect switch installed in an electrical system cannot only improve the operating flexibility, but also enhance the reliability for a wind farm. Therefore, this paper develops a probabilistic transfer technique for integrating the electrical topology structure, the isolation operation of disconnect switch, and stochastic failure of electrical equipment into the reliability assessment of wind farm electrical system. Firstly, as the traditional two-state reliability model of electrical equipment cannot consider the isolation operation, so the paper develops a three-state reliability model to replace the two-state model for incorporating the isolation operation. In addition, a proportion apportion technique is presented to evaluate the state probability. Secondly, this paper develops a probabilistic transfer technique based on the thoughts that through transfer the unreliability of electrical system to the energy transmission interruption of wind turbine generators (WTGs. Finally, some novel indices for describing the reliability of wind farm electrical system are designed, and the variance coefficient of the designed indices is used as a convergence criterion to determine the termination of the assessment process. The proposed technique is applied to the reliability assessment of a wind farm with the different topologies. The simulation results show that the proposed techniques are effective in practical applications.

An image processing technique for the radiographic assessment of vertebral derangements

Energy Technology Data Exchange (ETDEWEB)

Breen, A.C. (Anglo-European Coll. of Chiropractic, Bournemouth (UK)); Allen, R. (Southampton Univ. (UK). Dept. of Mechanical Engineering); Morris, A. (Odstock Hospital, Salisbury (UK). Dept. of Radiology)

1989-01-01

A technique for measuring inter-vertebral motion by the digitization and processing of intensifier images is described. The technique reduces the time and X-ray dosage currently required to make such assessments. The errors associated with computing kinematic indices at increments of coronal plane rotations in the lumbar spine have been calculated using a calibration model designed to produce a facsimile of in vivo conditions in terms of image quality and geometric distortion. (author).

BELIEFS AND PRACTICES OF QASHQAI TURKS WITHIN THE CIRCLE OF BIRTH KAŞKAY TÜRKLERİNDE DOĞUM ÇEVRESİNDE GELİŞEN İNANÇ VE PRATİKLER

Directory of Open Access Journals (Sweden)

Mehmet KARAASLAN

2011-09-01

Full Text Available In this study, which deals with the birth traditions of The Qashqai, and beliefs and practices in this aspect, the data gained through approximately two-month studies in the field of Iran are used. During the field of study, based on the use of techniques such as participated observation and question and answer, Qashqai people, both have urban live and haven’t plucked their ties with nomadism in appropriately with their current social tissues, have been discussed with. These rituals and beliefs formed within the frame of birth are examined through the perspectives such as their functions, whether they have an equivalent in the ancient Turkish culture or not and their comparison of aspects similar to the other communities of the world of the Turks. Kaşkayların doğum gelenekleri ve bu çerçevedeki inanç ve pratiklerinin ele alındığı bu çalışmada İran sahasında yaklaşık iki ay süresince yapılmış olan saha çalışmasında elde edilen veriler kullanılmıştır. Katılımlı gözlem ve soru cevap gibi tekniklerin kullanılması sureti ile yapılan saha çalışması sırasında Kaşkayların şu anki sosyal dokusuna uygun olarak hem uzun süredir şehir hayatı yaşayan hem göçerlikle bağlantılarını tam olarak koparmamış Kaşkaylarla görüşülmüştür. Doğum çevresinde teşekkül etmiş bu ritüel ve inançlar; işlevleri, kadim Türk kültüründe bir karşılıklarının olup olmadığı ve Türk dünyasının diğer toplulukları ile benzeyen yönlerinin mukayesesi gibi bakış açılarıyla irdelenmiştir.

Inspection of copper canisters for spent nuclear fuel by means of ultrasound. Ultrasonic imaging of EB weld, theory of harmonic imaging of welds, NDE of cast iron

International Nuclear Information System (INIS)

Stepinski, T.; Lingvall, F.; Ping Wu

2001-07-01

presented. The calculated results show how the harmonics evolve as the plane wave propagates. It should be noted that the work presented here is at its preliminary stage, the goal of the present and future work is to build a simulating tool for material harmonic imaging technology. The theory of phase conjugation is presented and different methods of wave phase conjugation (WPC) are reviewed and characterized in the third chapter. The ability of WPC to self-adaptive focus ultrasonic waves in inhomogeneous media makes it interesting in the application to the inspection of as EB welds. The WPC can be performed either in time or frequency domain. Time domain method, known as time reversal mirrors is reviewed in some detail with focus on its applications to NDT. Frequency domain techniques use nonlinear piezoelectric or magnetic materials. The choice of magneto-acoustic phase conjugation, performed in nonlinear magnetic ceramics as a candidate for the feasibility demonstration is motivated. Details of the preliminary experiment with high frequency NDE application (10 MHz) are presented. NDE methods suitable for the characterization of cast iron are reviewed in the fourth chapter. Two groups of methods that could be used in an industrial environment, those based on ultrasound and on eddy current measurement are presented in some detail. The review is focused on sensing the interaction of elastic waves with the microstructure of cast iron. It is explained how three different features of ultrasound, the sound velocity, the attenuation and the backscattering, can be used for the characterization

Inspection of copper canisters for spent nuclear fuel by means of ultrasound. Ultrasonic imaging of EB weld, theory of harmonic imaging of welds, NDE of cast iron

Energy Technology Data Exchange (ETDEWEB)

Stepinski, T.; Lingvall, F.; Ping Wu [Uppsala Univ. (Sweden). Dept. of Materials Science

2001-07-01

presented. The calculated results show how the harmonics evolve as the plane wave propagates. It should be noted that the work presented here is at its preliminary stage, the goal of the present and future work is to build a simulating tool for material harmonic imaging technology. The theory of phase conjugation is presented and different methods of wave phase conjugation (WPC) are reviewed and characterized in the third chapter. The ability of WPC to self-adaptive focus ultrasonic waves in inhomogeneous media makes it interesting in the application to the inspection of as EB welds. The WPC can be performed either in time or frequency domain. Time domain method, known as time reversal mirrors is reviewed in some detail with focus on its applications to NDT. Frequency domain techniques use nonlinear piezoelectric or magnetic materials. The choice of magneto-acoustic phase conjugation, performed in nonlinear magnetic ceramics as a candidate for the feasibility demonstration is motivated. Details of the preliminary experiment with high frequency NDE application (10 MHz) are presented. NDE methods suitable for the characterization of cast iron are reviewed in the fourth chapter. Two groups of methods that could be used in an industrial environment, those based on ultrasound and on eddy current measurement are presented in some detail. The review is focused on sensing the interaction of elastic waves with the microstructure of cast iron. It is explained how three different features of ultrasound, the sound velocity, the attenuation and the backscattering, can be used for the characterization.

Developing and Implementing an Assessment Technique to Measure Linked Concepts

Science.gov (United States)

Ye, Li; Oueini, Razanne; Lewis, Scott E.

2015-01-01

The links students make among chemistry content is considered essential for a robust, enduring understanding in multiple learning theories. This article describes the development and implementation of an assessment technique, termed a Measure of Linked Concepts, designed to inform instructors on students' understanding of linking content…

Development of ultrasonic testing DSP inspection technique for class 1 system piping in nuclear power plants

International Nuclear Information System (INIS)

Ku, Kil Mo; Lee, Ik Whan; Jeong, Hyun Kyu; Park, Moon Ho; Heo, Hyung; Kong, Un Sik

1996-01-01

The purpose of this study is to explore the utilization of new constant-Q SSP in ultrasonic NDE. Various engineering problems are reviewed, and suggestions for implementation of the technique are provided. The filters of new Constant-Q SSP centered on frequency points, and normalized type of the filtered signals was not nromalized. The new Constant-Q SSP uses the frequency-dependant response of the interfering coherent noise produced by unresolvable scatters in the resolution range cell of a transducer. It is implemented by splitting the frequency spectrum of the received signal with gaussian bandpass filters. The principles of the SSP and the various optimization algorithms are recalled, and the conventional decomposition method for the SSP was presented

Development of ultrasonic testing DSP inspection technique for class 1 system piping in nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Ku, Kil Mo; Lee, Ik Whan; Jeong, Hyun Kyu; Park, Moon Ho; Heo, Hyung; Kong, Un Sik [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1996-01-01

The purpose of this study is to explore the utilization of new constant-Q SSP in ultrasonic NDE. Various engineering problems are reviewed, and suggestions for implementation of the technique are provided. The filters of new Constant-Q SSP centered on frequency points, and normalized type of the filtered signals was not nromalized. The new Constant-Q SSP uses the frequency-dependant response of the interfering coherent noise produced by unresolvable scatters in the resolution range cell of a transducer. It is implemented by splitting the frequency spectrum of the received signal with gaussian bandpass filters. The principles of the SSP and the various optimization algorithms are recalled, and the conventional decomposition method for the SSP was presented.

Nuclear medicine techniques in the assessment of alkaptonuria.

Science.gov (United States)

Vinjamuri, Sobhan; Ramesh, Chandakacharla N; Jarvis, Jonathan; Gallagher, Jim A; Ranganath, Lakshminarayana L

2011-10-01

Alkaptonuria is a rare autosomal recessive disorder due to a lack of the enzyme homogentisate dioxygenase, leading to ochronosis, a process of accumulation of a melanin-like polymer of homogentisic acid in cartilage and other collagenous structures. Patients develop severe osteoarthropathy that resembles osteoarthritis. Although the diagnosis of alkaptonuria is not particularly challenging in view of the blue-black discolouration of visible connective tissue and the presence of homogentisic acid in urine, the natural history of alkaptonuria remains poorly understood. Patients would benefit immensely from an objective assessment of their disease status and from a clearer understanding of the pathophysiology and associated physical changes. Isotope bone scans, which are commonly used to identify the extent of involvement of bones in cancerous processes, have also been increasingly used for characterizing the extent of arthropathy in conditions such as osteoarthritis and rheumatoid arthritis. Semiquantitative scores based on the extent of involvement of joints have been used to describe the involvement of large joints in the context of symptomatic treatment for osteoarthritis. A similar semiquantitative isotope bone scan score depending on the involvement of the number of large joints in patients with alkaptonuria can be formulated and validated in a suitable cohort of patients. Bone densitometry measurement using dual-energy X-ray absorptiometry scanning is an internationally accepted tool to assess the risk and extent of osteoporosis, and is increasingly used to assess the additional fracture risk in patients with arthropathy. We believe that, currently, nuclear medicine techniques can provide useful information, which can be incorporated into disease severity scores for alkaptonuria. Once the biological basis for alkaptonuria is better understood, it is feasible that nuclear medicine techniques of even greater sensitivity and specificity can be developed, thereby

Strategic approaches and assessment techniques-Potential for knowledge brokerage towards sustainability

International Nuclear Information System (INIS)

Sheate, William R.; Partidario, Maria Rosario

2010-01-01

The role of science in policy and decision-making has been an issue of intensive debate over the past decade. The concept of knowledge brokerage has been developing in this context contemplating issues of communication, interaction, sharing of knowledge, contribution to common understandings, as well as to effective and efficient action. For environmental and sustainability policy and decision-making the discussion has addressed more the essence of the issue rather than the techniques that can be used to enable knowledge brokerage. This paper aims to contribute to covering this apparent gap in current discussion by selecting and examining empirical cases from Portugal and the United Kingdom that can help to explore how certain environmental and sustainability assessment approaches can contribute, if well applied, to strengthen the science-policy link. The cases show that strategic assessment approaches and techniques have the potential to promote knowledge brokerage, but a conscious effort will be required to design in genuine opportunities to facilitate knowledge exchange and transfer as part of assessment processes.

Neurophysiology and new techniques to assess esophageal sensory function: an update.

Science.gov (United States)

Brock, Christina; McCallum, Richard W; Gyawali, C Prakash; Farmer, Adam D; Frøkjaer, Jens Brøndum; McMahon, Barry P; Drewes, Asbjørn Mohr

2016-09-01

This review aims to discuss the neurophysiology of the esophagus and new methods to assess esophageal nociception. Pain and other symptoms can be caused by diseases in the mucosa or muscular or sphincter dysfunction, together with abnormal pain processing, either in the peripheral or central nervous systems. Therefore, we present new techniques in the assessment of esophageal function and the potential role of the mucosal barrier in the generation and propagation of pain. We discuss the assessment and role of esophageal sphincters in nociception, as well as imaging and electrophysiological techniques, with examples of their use in understanding the sensory system following noxious stimuli to the esophagus. Additionally, we discuss the mechanisms behind functional diseases of the esophagus. We conclude that the new methods have identified many of the mechanisms behind malfunction of the mucosa, disturbances of muscular and sphincter functions, and the central response to different stimuli. Taken together, this has increased our understanding of esophageal disorders and may lead to new treatment modalities. © 2016 New York Academy of Sciences.

A relative quantitative assessment of myocardial perfusion by first-pass technique: animal study

Science.gov (United States)

Chen, Jun; Zhang, Zhang; Yu, Xuefang; Zhou, Kenneth J.

2015-03-01

The purpose of this study is to quantitatively assess the myocardial perfusion by first-pass technique in swine model. Numerous techniques based on the analysis of Computed Tomography (CT) Hounsfield Unit (HU) density have emerged. Although these methods proposed to be able to assess haemodynamically significant coronary artery stenosis, their limitations are noticed. There are still needs to develop some new techniques. Experiments were performed upon five (5) closed-chest swine. Balloon catheters were placed into the coronary artery to simulate different degrees of luminal stenosis. Myocardial Blood Flow (MBF) was measured using color microsphere technique. Fractional Flow Reserve (FFR) was measured using pressure wire. CT examinations were performed twice during First-pass phase under adenosine-stress condition. CT HU Density (HUDCT) and CT HU Density Ratio (HUDRCT) were calculated using the acquired CT images. Our study presents that HUDRCT shows a good (y=0.07245+0.09963x, r2=0.898) correlation with MBF and FFR. In receiver operating characteristic (ROC) curve analyses, HUDRCT provides excellent diagnostic performance for the detection of significant ischemia during adenosine-stress as defined by FFR indicated by the value of Area Under the Curve (AUC) of 0.927. HUDRCT has the potential to be developed as a useful indicator of quantitative assessment of myocardial perfusion.

Crack-depth effects in the cylindrically guided wave technique for bolt and pump-shaft inspections

International Nuclear Information System (INIS)

Tsai, Y.M.; Liu, S.N.; Light, G.M.

1991-01-01

Nuclear power plants have experienced the failures of bolts and pump shafts. The industry is concerned about nondestructive evaluation (NDE) techniques that can be applied to these components. The cylindrically guided wave technique (CGWT) has been developed to detect the simulated circumferential defects in long bolts and studs. The ultrasonic CGWT employs the zero-degree longitudinal waves constrained to travel within the boundary of the components with cylindrical shape during inspection. When longitudinal waves are guided to travel along a cylinder, and impinge onto a circumferential defect, the waves are scattered at the crack on the cylinder surface. In this work, the wave scattering at the circumferential crack on a long cylinder is investigated. The transfer factor of the scattered waves is calculated for a wide range of frequency spectra. The scattered waveform at a distance away from a crack is calculated. The effect that crack depth exerts to the waveform in CGWT is shown. CGWT signals, waveform calculation and so on are reported. (K.I.)

Fundamental and assessment of concrete structure monitoring by using acoustic emission technique testing: A review

Science.gov (United States)

Desa, M. S. M.; Ibrahim, M. H. W.; Shahidan, S.; Ghadzali, N. S.; Misri, Z.

2018-04-01

Acoustic emission (AE) technique is one of the non-destructive (NDT) testing, where it can be used to determine the damage of concrete structures such as crack, corrosion, stability, sensitivity, as structure monitoring and energy formed within cracking opening growth in the concrete structure. This article gives a comprehensive review of the acoustic emission (AE) technique testing due to its application in concrete structure for structural health monitoring (SHM). Assessment of AE technique used for structural are reviewed to give the perception of its structural engineering such as dam, bridge and building, where the previous research has been reviewed based on AE application. The assessment of AE technique focusing on basic fundamental of parametric and signal waveform analysis during analysis process and its capability in structural monitoring. Moreover, the assessment and application of AE due to its function have been summarized and highlighted for future references

Reliability of System Identification Techniques to Assess Standing Balance in Healthy Elderly.

Directory of Open Access Journals (Sweden)

Jantsje H Pasma

Full Text Available System identification techniques have the potential to assess the contribution of the underlying systems involved in standing balance by applying well-known disturbances. We investigated the reliability of standing balance parameters obtained with multivariate closed loop system identification techniques.In twelve healthy elderly balance tests were performed twice a day during three days. Body sway was measured during two minutes of standing with eyes closed and the Balance test Room (BalRoom was used to apply four disturbances simultaneously: two sensory disturbances, to the proprioceptive and the visual system, and two mechanical disturbances applied at the leg and trunk segment. Using system identification techniques, sensitivity functions of the sensory disturbances and the neuromuscular controller were estimated. Based on the generalizability theory (G theory, systematic errors and sources of variability were assessed using linear mixed models and reliability was assessed by computing indexes of dependability (ID, standard error of measurement (SEM and minimal detectable change (MDC.A systematic error was found between the first and second trial in the sensitivity functions. No systematic error was found in the neuromuscular controller and body sway. The reliability of 15 of 25 parameters and body sway were moderate to excellent when the results of two trials on three days were averaged. To reach an excellent reliability on one day in 7 out of 25 parameters, it was predicted that at least seven trials must be averaged.This study shows that system identification techniques are a promising method to assess the underlying systems involved in standing balance in elderly. However, most of the parameters do not appear to be reliable unless a large number of trials are collected across multiple days. To reach an excellent reliability in one third of the parameters, a training session for participants is needed and at least seven trials of two

Reviewing effectiveness of ankle assessment techniques for use in robot-assisted therapy.

Science.gov (United States)

Zhang, Mingming; Davies, T Claire; Zhang, Yanxin; Xie, Shane

2014-01-01

This article provides a comprehensive review of studies that investigated ankle assessment techniques to better understand those that can be used in the real-time monitoring of rehabilitation progress for implementation in conjunction with robot-assisted therapy. Seventy-six publications published between January 1980 and August 2013 were selected based on eight databases. They were divided into two main categories (16 qualitative and 60 quantitative studies): 13 goniometer studies, 18 dynamometer studies, and 29 studies about innovative techniques. A total of 465 subjects participated in the 29 quantitative studies of innovative measurement techniques that may potentially be integrated in a real-time monitoring device, of which 19 studies included less than 10 participants. Results show that qualitative ankle assessment methods are not suitable for real-time monitoring in robot-assisted therapy, though they are reliable for certain patients, while the quantitative methods show great potential. The majority of quantitative techniques are reliable in measuring ankle kinematics and kinetics but are usually available only for use in the sagittal plane. Limited studies determine kinematics and kinetics in all three planes (sagittal, transverse, and frontal) where motions of the ankle joint and the subtalar joint actually occur.

Assessment and evaluation of ceramic filter cleaning techniques: Task Order 19

Energy Technology Data Exchange (ETDEWEB)

Chen, H.; Zaharchuk, R.; Harbaugh, L.B.; Klett, M.

1994-10-01

The objective of this study was to assess and evaluate the effectiveness, appropriateness and economics of ceramic barrier filter cleaning techniques used for high-temperature and high-pressure particulate filtration. Three potential filter cleaning techniques were evaluated. These techniques include, conventional on-line pulse driven reverse gas filter cleaning, off-line reverse gas filter cleaning and a novel rapid pulse driven filter cleaning. These three ceramic filter cleaning techniques are either presently employed, or being considered for use, in the filtration of coal derived gas streams (combustion or gasification) under high-temperature high-pressure conditions. This study was divided into six subtasks: first principle analysis of ceramic barrier filter cleaning mechanisms; operational values for parameters identified with the filter cleaning mechanisms; evaluation and identification of potential ceramic filter cleaning techniques; development of conceptual designs for ceramic barrier filter systems and ceramic barrier filter cleaning systems for two DOE specified power plants; evaluation of ceramic barrier filter system cleaning techniques; and final report and presentation. Within individual sections of this report critical design and operational issues were evaluated and key findings were identified.

Stable Isotope Technique to Assess Intake of Human Milk in Breastfed Infants

International Nuclear Information System (INIS)

2014-01-01

This publication was developed by an international group of experts as an integral part of the IAEA’s efforts to contribute to the transfer of technology and knowledge in nutrition. Its aim is to assist Member States in their efforts to combat malnutrition by facilitating the use of relevant nuclear techniques. The stable (non-radioactive) isotope technique has been developed to assess intake of human milk in breastfed infants. The practical application of the stable isotope technique, based on analysis of deuterium by Fourier transform infrared spectrometry (FTIR), is presented in this book

[Hand hygiene technique assessment using electronic equipment in 26 Hungarian healthcare institutions].

Science.gov (United States)

Lehotsky, Ákos; Morvai, Júlia; Szilágyi, László; Bánsághi, Száva; Benkó, Alíz; Haidegger, Tamás

2017-07-01

Hand hygiene is probably the most effective tool of nosocomial infection prevention, however, proper feedback and control is needed to develop the individual hand hygiene practice. Assessing the efficiency of modern education tools, and digital demonstration and verification equipment during their wide-range deployment. 1269 healthcare workers took part in a training organized by our team. The training included the assessment of the participants' hand hygiene technique to identify the most often missed areas. The hand hygiene technique was examined by a digital device. 33% of the participants disinfected their hands incorrectly. The most often missed sites are the fingertips (33% on the left hand, 37% on the right hand) and the thumbs (42% on the left hand, 32% on the right hand). The feedback has a fundamental role in the development of the hand hygiene technique. With the usage of electronic devices feedback can be provided efficiently and simply. Orv Hetil. 2017; 158(29): 1143-1148.

Nonlinear ultrasonic stimulated thermography for damage assessment in isotropic fatigued structures

Science.gov (United States)

Fierro, Gian Piero Malfense; Calla', Danielle; Ginzburg, Dmitri; Ciampa, Francesco; Meo, Michele

2017-09-01

Traditional non-destructive evaluation (NDE) and structural health monitoring (SHM) systems are used to analyse that a structure is free of any harmful damage. However, these techniques still lack sensitivity to detect the presence of material micro-flaws in the form of fatigue damage and often require time-consuming procedures and expensive equipment. This research work presents a novel "nonlinear ultrasonic stimulated thermography" (NUST) method able to overcome some of the limitations of traditional linear ultrasonic/thermography NDE-SHM systems and to provide a reliable, rapid and cost effective estimation of fatigue damage in isotropic materials. Such a hybrid imaging approach combines the high sensitivity of nonlinear acoustic/ultrasonic techniques to detect micro-damage, with local defect frequency selection and infrared imaging. When exciting structures with an optimised frequency, nonlinear elastic waves are observed and higher frictional work at the fatigue damaged area is generated due to clapping and rubbing of the crack faces. This results in heat at cracked location that can be measured using an infrared camera. A Laser Vibrometer (LV) was used to evaluate the extent that individual frequency components contribute to the heating of the damage region by quantifying the out-of-plane velocity associated with the fundamental and second order harmonic responses. It was experimentally demonstrated the relationship between a nonlinear ultrasound parameter (βratio) of the material nonlinear response to the actual temperature rises near the crack. These results demonstrated that heat generation at damaged regions could be amplified by exciting at frequencies that provide nonlinear responses, thus improving the imaging of material damage and the reliability of NUST in a quick and reproducible manner.

A new technique for assessing fish passage survival at hydro power stations

International Nuclear Information System (INIS)

Heisey, P.G.; Mathur, D.; D'Allesandro, L.

1993-01-01

The HI-Z Turb'N Tag recovery method is presented as a new technique that has been successfully used at ten hydropower stations to determine turbine or spillway passage survival of fish. According to this technique, fish are tagged with the Turb'N Tag, which is pear-shaped, made of inflatable latex, and ca 35 mm long and 13 mm wide. The tag is designed to inflate after passage through the turbine, where it then floats the fish to the surface where it can be easily spotted and netted. One tag is sufficient to retrieve fish less than 18 cm long, while three tags may be needed for fish longer than 30 cm. In tests, fish were recovered in under 10 minutes from the tailrace after being tagged and released into a turbine. The tag allowed over 90% recovery of fish in most tests. The technique had minimal effect on the well-being of both hardy and sensitive species and provided an opportunity to examine recovered fish for injuries and retain them up to 72 h to assess possible delayed effects. The technique overcomes most of the logistical problems associated with conventional methods (netting, radio telemetry, mass mark-recapture) to determine turbine passage survival. The technique can also be used to assess effects of spill and fish bypass structures. 9 refs., 2 figs., 1 tab

Fractal dimension analysis for robust ultrasonic non-destructive evaluation (NDE) of coarse grained materials

Science.gov (United States)

Li, Minghui; Hayward, Gordon

2018-04-01

Over the recent decades, there has been a growing demand on reliable and robust non-destructive evaluation (NDE) of structures and components made from coarse grained materials such as alloys, stainless steels, carbon-reinforced composites and concrete; however, when inspected using ultrasound, the flaw echoes are usually contaminated by high-level, time-invariant, and correlated grain noise originating from the microstructure and grain boundaries, leading to pretty low signal-to-noise ratio (SNR) and the flaw information being obscured or completely hidden by the grain noise. In this paper, the fractal dimension analysis of the A-scan echoes is investigated as a measure of complexity of the time series to distinguish the echoes originating from the real defects and the grain noise, and then the normalized fractal dimension coefficients are applied to the amplitudes as the weighting factor to enhance the SNR and defect detection. Experiments on industrial samples of the mild steel and the stainless steel are conducted and the results confirm the great benefits of the method.

A comparison of techniques for assessing farmland bumblebee populations.

Science.gov (United States)

Wood, T J; Holland, J M; Goulson, D

2015-04-01

Agri-environment schemes have been implemented across the European Union in order to reverse declines in farmland biodiversity. To assess the impact of these schemes for bumblebees, accurate measures of their populations are required. Here, we compared bumblebee population estimates on 16 farms using three commonly used techniques: standardised line transects, coloured pan traps and molecular estimates of nest abundance. There was no significant correlation between the estimates obtained by the three techniques, suggesting that each technique captured a different aspect of local bumblebee population size and distribution in the landscape. Bumblebee abundance as observed on the transects was positively influenced by the number of flowers present on the transect. The number of bumblebees caught in pan traps was positively influenced by the density of flowers surrounding the trapping location and negatively influenced by wider landscape heterogeneity. Molecular estimates of the number of nests of Bombus terrestris and B. hortorum were positively associated with the proportion of the landscape covered in oilseed rape and field beans. Both direct survey techniques are strongly affected by floral abundance immediately around the survey site, potentially leading to misleading results if attempting to infer overall abundance in an area or on a farm. In contrast, whilst the molecular method suffers from an inability to detect sister pairs at low sample sizes, it appears to be unaffected by the abundance of forage and thus is the preferred survey technique.

Perceptions of Teachers towards Assessment Techniques at Secondary Level Private School of Karachi

Directory of Open Access Journals (Sweden)

Henna Fatemah

2015-12-01

Full Text Available This paper sets out to explore the perceptions of teachers towards assessment techniques at a secondary level private school of Karachi. This was conjectured on the basis of the circumstances of parallel boards in the education system of Pakistan and its effectiveness within the context with respect to the curriculum. This was gauged in line with the forms and techniques of assessment corresponding with the curriculum. A qualitative research design based on interviews was chosen for this study. Purposive sampling was used to select the teachers from a school. The findings of the study revealed that the General Certificate of Secondary Education (GCSE is best suited to assess students’ knowledge and skills and the teachers viewed that in order for students to be accomplished in this board, the ways of assessment must take a more meaningful measure of evaluating student’s progress

Comparison between manual and automated techniques for assessment of data from dynamic antral scintigraphy

International Nuclear Information System (INIS)

Misiara, Gustavo P.; Troncon, Luiz E.A.; Secaf, Marie; Moraes, Eder R.

2008-01-01

This work aimed at determining whether data from dynamic antral scintigraphy (DAS) yielded by a simple, manual technique are as accurate as those generated by a conventional automated technique (fast Fourier transform) for assessing gastric contractility. Seventy-one stretches (4 min) of 'activity versus time' curves obtained by DAS from 10 healthy volunteers and 11 functional dyspepsia patients, after ingesting a liquid meal (320 ml, 437 kcal) labeled with technetium-99m ( 99m Tc)-phytate, were independently analyzed by manual and automated techniques. Data obtained by both techniques for the frequency of antral contractions were similar. Contraction amplitude determined by the manual technique was significantly higher than that estimated by the automated method, in both patients and controls. The contraction frequency 30 min post-meal was significantly lower in patients than in controls, which was correctly shown by both techniques. A manual technique using ordinary resources of the gamma camera workstation, despite yielding higher figures for the amplitude of gastric contractions, is as accurate as the conventional automated technique of DAS analysis. These findings may favor a more intensive use of DAS coupled to gastric emptying studies, which would provide a more comprehensive assessment of gastric motor function in disease. (author)

Nondestructive characterization of low-level transuranic waste

International Nuclear Information System (INIS)

Barna, B.A.; Reinhardt, W.W.

1981-10-01

The use of nondestructive evaluation (NDE) methods is proposed for characterization of transuranic (TRU) waste stored at the Radioactive Waste Management Complex. These NDE methods include real-time x-ray radiography, real-time neutron radiography, x-ray and neutron computed tomography, thermal imaging, container weighing, visual examination, and acoustic measurements. An integrated NDE system is proposed for characterization and certification of TRU waste destined for eventual shipment to the Waste Isolation Pilot Plant in New Mexico. Methods for automating both the classification waste and control of a complete nondestructive evaluation/nondestructive assay system are presented. Feasibility testing of the different NDE methods, including real-time x-ray radiography, and development of automated waste classification techniques are covered as part of a five year effort designed to yield a production waste characterization system

Evolution of a seismic risk assessment technique

International Nuclear Information System (INIS)

Wells, J.E.; Cummings, G.E.

1985-01-01

To assist the NRC in its licensing evaluation role the Seismic Safety Margins Research Program (SSMRP) was started at LLNL in 1978. Its goal was to develop tools and data bases to evaluate the probability of earthquake caused radioactive releases from commercial nuclear power plants. The methodology was finalized in 1982 and a seismic risk assessment of the Zion Nuclear Power Plant was finished in 1983. Work continues on the study of the LaSalle Boiling Water Reactor. This paper will discuss some of the effects of the assumptions made during development of the systems analysis techniques used in SSMRP in light of the results obtained on studies to date. 5 refs

Martin Mayman's early memories technique: bridging the gap between personality assessment and psychotherapy.

Science.gov (United States)

Fowler, J C; Hilsenroth, M J; Handler, L

2000-08-01

In this article, we describe Martin Mayman's approach to early childhood memories as a projective technique, beginning with his scientific interest in learning theory, coupled with his interest in ego psychology and object relations theory. We describe Mayman's contributions to the use of the early memories technique to inform the psychotherapy process, tying assessment closely to psychotherapy and making assessment more useful in treatment. In this article, we describe a representative sample of research studies that demonstrate the reliability and validity of early memories, followed by case examples in which the early memories informed the therapy process, including issues of transference and countertransference.

Viscoelastic assessment of anal canal function using acoustic reflectometry: a clinically useful technique.

Science.gov (United States)

Mitchell, Peter J; Klarskov, Niels; Telford, Karen J; Hosker, Gordon L; Lose, Gunnar; Kiff, Edward S

2012-02-01

Anal acoustic reflectometry is a new reproducible technique that allows a viscoelastic assessment of anal canal function. Five new variables reflecting anal canal function are measured: the opening and closing pressure, opening and closing elastance, and hysteresis. The aim of this study was to assess whether the parameters measured in anal acoustic reflectometry are clinically valid between continent and fecally incontinent subjects. This was an age- and sex-matched study of continent and incontinent women. The study was conducted at a university teaching hospital. One hundred women (50 with fecal incontinence and 50 with normal bowel control) were included in the study. Subjects were age matched to within 5 years. Parameters measured with anal acoustic reflectometry and manometry were compared between incontinent and continent groups using a paired t test. Diagnostic accuracy was assessed by the use of receiver operator characteristic curves. Four of the 5 anal acoustic reflectometry parameters at rest were significantly different between continent and incontinent women (eg, opening pressure in fecally incontinent subjects was 31.6 vs 51.5 cm H2O in continent subjects, p = 0.0001). Both anal acoustic reflectometry parameters of squeeze opening pressure and squeeze opening elastance were significantly reduced in the incontinent women compared with continent women (50 vs 99.1 cm H2O, p = 0.0001 and 1.48 vs 1.83 cm H2O/mm, p = 0.012). In terms of diagnostic accuracy, opening pressure at rest measured by reflectometry was significantly superior in discriminating between continent and incontinent women in comparison with resting pressure measured with manometry (p = 0.009). Anal acoustic reflectometry is a new, clinically valid technique in the assessment of continent and incontinent subjects. This technique, which assesses the response of the anal canal to distension and relaxation, provides a detailed viscoelastic assessment of anal canal function. This technique

Endüstriyel İşletmelerde Franchising Model Önerisi: Hazır Beton Sektöründe Bir Uygulama

Directory of Open Access Journals (Sweden)

İpek Kazançoğlu

2016-12-01

Full Text Available Endüstriyel pazarda faaliyet gösteren firmaların daha hızlı büyüyerek, yeni pazarlara açılmasında franchising sistemi bir yeni bir satış, dağıtım kanalı olarak değerlendirilmektedir. Bu araştırmada amaç,  hazır beton sektöründe faaliyet gösteren bir firmanın franchising sistemini bir iş modeli olarak benimseme kararında dikkat etmesi gereken unsurları ve karşılaşılan zorlukları incelemektedir. Örnek olay çalışması olarak ele alınan çalışmada,  BATIBETON A.Ş. firmasının yedi yöneticiyle BATIBETON markasının franchising uygulamalarına ilişkin görüşlerini öğrenmek amacıyla derinlemesine görüşmeler yapılmıştır. Bu görüşmeler sonucunda, franchising sisteminin hazır beton sektöründe bir model önerisi olarak uygulanıp/uygulanmayacağı değerlendirilmiştir. Yapılan görüşmelerden elde edilen bulguların diğer endüstriyel işletmeler içinde geliştirilebilecek bir franchising iş modeli kararında etkili olabilecek faktörlerin anlaşılması yönünden uygulamaya katkı sağlayacağı düşünülmektedir.

Täter- und Opfergeschichten. Schuld in Alois Hotschnigs Prosawerken «Aus», «Leonardos Hände» und «Ludwigs Zimmer»

Directory of Open Access Journals (Sweden)

Friederike Gösweiner

2014-05-01

Full Text Available The assumption this article is based on is that guilt is perhaps the most important theme in Alois Hotschnig’s writing. This article therefore aims at analyzing Hotschnig’s focus on the theme of guilt in his novels. Three examples of Hotschnig’s prose work serve as case studies: his debut Aus, and the two novels Leonardos Hände, and Ludwigs Zimmer. Since guilt seems to be a very important topic in the Austrian literary tradition, this article also tries to establish whether and how Hotschnig takes up this grand Austrian tradition of writing about guilt.

Educational ultrasound nondestructive testing laboratory.

Science.gov (United States)

Genis, Vladimir; Zagorski, Michael

2008-09-01

The ultrasound nondestructive evaluation (NDE) of materials course was developed for applied engineering technology students at Drexel University's Goodwin College of Professional Studies. This three-credit, hands-on laboratory course consists of two parts: the first part with an emphasis on the foundations of NDE, and the second part during which ultrasound NDE techniques are utilized in the evaluation of parts and materials. NDE applications are presented and applied through real-life problems, including calibration and use of the latest ultrasonic testing instrumentation. The students learn engineering and physical principles of measurements of sound velocity in different materials, attenuation coefficients, material thickness, and location and dimensions of discontinuities in various materials, such as holes, cracks, and flaws. The work in the laboratory enhances the fundamentals taught during classroom sessions. This course will ultimately result in improvements in the educational process ["The greater expectations," national panel report, http://www.greaterexpectations.org (last viewed February, 2008); R. M. Felder and R. Brent "The intellectual development of Science and Engineering Students. Part 2: Teaching to promote growth," J. Eng. Educ. 93, 279-291 (2004)] since industry is becoming increasingly reliant on the effective application of NDE technology and the demand on NDE specialists is increasing. NDE curriculum was designed to fulfill levels I and II NDE in theory and training requirements, according to American Society for Nondestructive Testing, OH, Recommended Practice No. SNT-TC-1A (2006).

Life-assessment technique for nuclear power plant cables

International Nuclear Information System (INIS)

Bartonicek, B.; Hnat, V.; Placek, V.

1998-01-01

The condition of polymer-based cable material can be best characterized by measuring elongation at break of its insulating materials. However, it is not often possible to take sufficiently large samples for measurement with the tensile testing machine. The problem has been conveniently solved by utilizing differential scanning calorimetry technique. From the tested cable, several microsamples are taken and the oxidation induction time (OIT) is determined. For each cable which is subject to the assessment of the lifetime, the correlation of OIT with elongation at break and the correlation of elongation at break with the cable service time has to be performed. A reliable assessment of the cable lifetime depends on accuracy of these correlations. Consequently, synergistic effects well known at this time - dose rate effects and effects resulting from the different sequence of applying radiation and elevated temperature must be taken into account

Comparing and assessing different measurement techniques for mercury in coal systhesis gas

Energy Technology Data Exchange (ETDEWEB)

Maxwell, D.P.; Richardson, C.F. [Radian Corporation, Austin, TX (United States)

1995-11-01

Three mercury measurement techniques were performed on synthesis gas streams before and after an amine-based sulfur removal system. The syngas was sampled using (1) gas impingers containing a nitric acid-hydrogen peroxide solution, (2) coconut-based charcoal sorbent, and (3) an on-line atomic absorption spectrophotometer equipped with a gold amalgamation trap and cold vapor cell. Various impinger solutions were applied upstream of the gold amalgamation trap to remove hydrogen sulfide and isolate oxidized and elemental species of mercury. The results from these three techniques are compared to provide an assessment of these measurement techniques in reducing gas atmospheres.

Study to define NDE research for inspection of stainless steels

International Nuclear Information System (INIS)

Reinhart, E.R.

1978-08-01

After the boiling water reactor (BWR) stress corrosion cracking incidents on 4- and 10-inch stainless steel piping, the Electric Power Research Institute (EPRI) organized a round-robin ultrasonic examination of piping removed from service (TPS-75-609). Five inspection teams participated in this program, using both a standard procedure and the individual team procedure. The original intent was to section the piping after the program to evaluate the effectiveness of state-of-the-art ultrasonics in finding stress corrosion cracking. The sectioning was delayed, however, to allow research and development (R and D) groups time to perform basic measurements aimed at determining optimum search unit and instrument characteristics for the ultrasonic examination of stainless steel piping and to study the applicability of various advanced inspection methods. This additional effort was funded as part of an EPRI technical planning study (TPS-75-620), A Study to Define NDE Research for Inspection of Stainless Steels. Inspection methods evaluated in this study included (1) processing of manual scan data using a miniature programmable calculator (Aerojet Nuclear); (2) investigation into the performance characteristics of three experimental ultrasonic transducers (Battelle-Columbus Laboratories); (3) analysis of fundamental ultrasonic response data from intergranular stress corrosion cracks in stainless steels (Southwest Research Institute); and (4) a feasibility study of advanced signal processing and pattern recognition for analyzing flaws in stainless steel piping (Ultrasonics International). The results of the studies compiled in the report have indicated the direction for future research and development and have formed the basis for the recently initiated EPRI Research Project 892, Ultrasonic System Optimization

Using Low-Frequency Phased Arrays to Detect Cracks in Cast Austenitic Piping Components

International Nuclear Information System (INIS)

Anderson, Michael T.; Cumblidge, Stephen E.; Doctor, Steven R.

2005-01-01

As part of a multi-year program funded by the United States Nuclear Regulatory Commission (US NRC) to address NDE reliability of inservice inspection (ISI) programs, recent studies conducted at the Pacific Northwest National Laboratory (PNNL) in Richland, Washington, have focused on assessing novel NDE approaches for the inspection of coarse-grained, cast stainless steel reactor components. The primary objective of this work is to provide information to the US NRC on the utility, effectiveness and reliability of ultrasonic testing (UT) and eddy current testing (ET) inspection techniques as related to the ISI of primary piping components in pressurized water reactors (PWRs). This paper describes progress, recent developments and early results from an assessment of a portion of this work relating to the ultrasonic low frequency phased array inspection technique. Westinghouse Owner's Group (WOG) cast stainless steel pipe segments with thermal and mechanical fatigue cracks, PNNL samples containing thermal fatigue cracks and several blank vintage specimens having very coarse grains that are representative of early centrifugally cast piping installed in PWRs, are being used for assessing the inspection method. The phased array approach was implemented using an R/D Tech Tomoscan III system operating at 1.0 MHz and 500 kHz, providing composite volumetric images of the samples. Several dual, transmit-receive, custom designed low-frequency arrays are employed in laboratory trials. Results from laboratory studies for assessing detection of thermal and mechanical fatigue cracks in cast stainless steel piping welds are discussed

TECHNIQUE OF AN ASSESSMENT OF COMPETITIVENESS OF THE ENTERPRISES OF THE FURNITURE INDUSTRY

Directory of Open Access Journals (Sweden)

Vitaliy A. Zhigarev

2015-01-01

Full Text Available The purpose of this article is the description of an author’s technique of an assessment of competitiveness of the enterprises of the furniture industry which mainobjective is the economic assessment ofproduction efficiency of production of thefurniture enterprise, an assessment ofthe intra firm making production efficiencyof furniture, identification of the factors influencing overall performance of thefurniture enterprise.

Assessment and comparison of the effects of two techniques on hamstring flexibility

Directory of Open Access Journals (Sweden)

Marcelo Tavella Navega

Full Text Available Introduction There are several stretching techniques that help increase flexibility, however, there are still questions regarding which method leads to the most effective gains. Objectives To assess and compare the effects of two stretching techniques, namely proprioceptive neuromuscular facilitation (PNF and static stretching on the flexibility of hamstring muscles of young women. Methods The study sample consisted of 45 young women, mean age 20.45 (± 1.66,assigned to one of three groups: static stretching group (SSG, n = 15, proprioceptive neuromuscular facilitation group (PNFG, n = 15 and control group (CG, n = 15. Both SSG and PNFG carried out three weekly stretching sessions over a four-week period. The sit and reach and popliteal angle tests were used at the beginning and end of the intervention. Normally distributed data were analyzed using Student’s t-test, whereas data with non-normal distribution were analyzed using the Wilcoxon test, to compare initial and end measurements for each technique. Finally, we used the Mann-Whitney U test to compare both techniques with each other. A significance level of 5% (p < 0.05 was adopted. Results There was a significant increase in hamstring flexibility when analyzing the assessments and reassessments of both stretching protocols. Conclusions Both techniques were effective in increasing hamstring flexibility and there were no significant differences to indicate which one is better in increasing the flexibility of this muscle group.

Using ecosystem modelling techniques in exposure assessments of radionuclides - an overview

International Nuclear Information System (INIS)

Kumblad, L.

2005-01-01

The risk to humans from potential releases from nuclear facilities is evaluated in safety assessments. Essential components of these assessments are exposure models, which estimate the transport of radionuclides in the environment, the uptake in biota, and transfer to humans. Recently, there has been a growing concern for radiological protection of the whole environment, not only humans, and a first attempt has been to employ model approaches based on stylized environments and transfer functions to biota based exclusively on bioconcentration factors (BCF). They are generally of a non-mechanistic nature and involve no knowledge of the actual processes involved, which is a severe limitation when assessing real ecosystems. in this paper, the possibility of using an ecological modelling approach as a complement or an alternative to the use of BCF-based models is discussed. The paper gives an overview of ecological and ecosystem modelling and examples of studies where ecosystem models have been used in association to ecological risk assessment studies for other pollutants than radionuclides. It also discusses the potential to use this technique in exposure assessments of radionuclides with a few examples from the safety assessment work performed by the Swedish nuclear fuel and waste management company (SKB). Finally there is a comparison of the characteristics of ecosystem models and traditionally exposure models for radionuclides used to estimate the radionuclide exposure of biota. The evaluation of ecosystem models already applied in safety assessments has shown that the ecosystem approach is possible to use to assess exposure to biota, and that it can handle many of the modelling problems identified related to BCF-models. The findings in this paper suggest that both national and international assessment frameworks for protection of the environment from ionising radiation would benefit from striving to adopt methodologies based on ecologically sound principles and

Russian Language Development Assessment as a Standardized Technique for Assessing Communicative Function in Children Aged 3–9 Years

Directory of Open Access Journals (Sweden)

Prikhoda N.A.,

2016-10-01

Full Text Available The article describes the Russian Language Development Assessment, a standardized individual diagnostic tool for children aged from 3 to 9 that helps to assess the following components of a child’s communicative function: passive vocabulary, expressive vocabulary, knowledge of semantic constructs with logical, temporal and spatial relations, passive perception and active use of syntactic and morphological features of words in a sentence, active and passive phonological awareness, active and passive knowledge of syntactic structures and categories. The article provides descriptions of content and diagnostic procedures for all 7 subtests included in the assessment (Passive Vocabulary, Active Vocabulary, Linguistic Operators, Sentence structure, Word Structure, Phonology, Sentence Repetition. Basing on the data collected in the study that involved 86 first- graders of a Moscow school, the article analyzes the internal consistency and construct validity of each subtest of the technique. It concludes that the Russian Language Development Assessment technique can be of much use both in terms of diagnostic purposes and in supporting children with ASD taking into account the lack of standardized tools for language and speech development assessment in Russian and the importance of this measure in general.

WASTE PACKAGE OPERATIONS FY99 CLOSURE METHODS REPORT

Energy Technology Data Exchange (ETDEWEB)

M. C. Knapp

1999-09-23

The waste package (WP) closure weld development task is part of a larger engineering development program to develop waste package designs. The purpose of the larger waste package engineering development program is to develop nuclear waste package fabrication and closure methods that the Nuclear Regulatory Commission will find acceptable and will license for disposal of spent nuclear fuel (SNF), non-fuel components, and vitrified high-level waste within a Monitored Geologic Repository (MGR). Within the WP closure development program are several major development tasks, which, in turn, are divided into subtasks. The major tasks include: WP fabrication development, WP closure weld development, nondestructive examination (NDE) development, and remote in-service inspection development. The purpose of this report is to present the objectives, technical information, and work scope relating to the WP closure weld development.and NDE tasks and subtasks and to report results of the closure weld and NDE development programs for fiscal year 1999 (FY-99). The objective of the FY-99 WP closure weld development task was to develop requirements for closure weld surface and volumetric NDE performance demonstrations, investigate alternative NDE inspection techniques, and develop specifications for welding, NDE, and handling system integration. In addition, objectives included fabricating several flat plate mock-ups that could be used for NDE development, stress relief peening, corrosion testing, and residual stress testing.

WASTE PACKAGE OPERATIONS FY-99 CLOSURE METHODS REPORT

International Nuclear Information System (INIS)

M. C. Knapp

1999-01-01

The waste package (WP) closure weld development task is part of a larger engineering development program to develop waste package designs. The purpose of the larger waste package engineering development program is to develop nuclear waste package fabrication and closure methods that the Nuclear Regulatory Commission will find acceptable and will license for disposal of spent nuclear fuel (SNF), non-fuel components, and vitrified high-level waste within a Monitored Geologic Repository (MGR). Within the WP closure development program are several major development tasks, which, in turn, are divided into subtasks. The major tasks include: WP fabrication development, WP closure weld development, nondestructive examination (NDE) development, and remote in-service inspection development. The purpose of this report is to present the objectives, technical information, and work scope relating to the WP closure weld development.and NDE tasks and subtasks and to report results of the closure weld and NDE development programs for fiscal year 1999 (FY-99). The objective of the FY-99 WP closure weld development task was to develop requirements for closure weld surface and volumetric NDE performance demonstrations, investigate alternative NDE inspection techniques, and develop specifications for welding, NDE, and handling system integration. In addition, objectives included fabricating several flat plate mock-ups that could be used for NDE development, stress relief peening, corrosion testing, and residual stress testing

The Effect of Learning Based on Technology Model and Assessment Technique toward Thermodynamic Learning Achievement

Science.gov (United States)

Makahinda, T.

2018-02-01

The purpose of this research is to find out the effect of learning model based on technology and assessment technique toward thermodynamic achievement by controlling students intelligence. This research is an experimental research. The sample is taken through cluster random sampling with the total respondent of 80 students. The result of the research shows that the result of learning of thermodynamics of students who taught the learning model of environmental utilization is higher than the learning result of student thermodynamics taught by simulation animation, after controlling student intelligence. There is influence of student interaction, and the subject between models of technology-based learning with assessment technique to student learning result of Thermodynamics, after controlling student intelligence. Based on the finding in the lecture then should be used a thermodynamic model of the learning environment with the use of project assessment technique.

Near-Death Experiences in a Multi-religious Hospital Population in Sri Lanka.

Science.gov (United States)

Chandradasa, Miyuru; Wijesinghe, Chamara; Kuruppuarachchi, K A L A; Perera, Mahendra

2017-07-01

Near-death experiences (NDEs) are a wide range of experiences that occur in association with impending death. There are no published studies on NDEs in general hospital populations, and studies have been mainly conducted on critically ill patients. We assessed the prevalence of NDEs and its associations in a multi-religious population in a general hospital in Sri Lanka. A randomised sample of patients admitted to the Colombo North Teaching Hospital was assessed using the Greyson NDE scale and clinical assessment. Out of total 826 participants, NDEs were described by 3%. Compared to the NDE-negative participants, the NDE-positive group had a significantly higher mean for age and a ratio of men. Women reported deeper NDEs. Patients of theistic religions (Christianity, Islam and Hinduism) reported significantly more NDEs compared to patients from the non-theistic religious group (Buddhism). NDE-positive patient group had significantly higher reporting of a feeling 'that they are about to die', the presence of loss of consciousness and a higher percentage of internal medical patients. This is the first time that NDEs are assessed in a general hospital population and NDEs being reported from Sri Lanka. We also note for the first time that persons with theistic religious beliefs reported more NDEs than those with non-theistic religious beliefs. Medical professionals need to be aware of these phenomena to be able to give an empathic hearing to patients who have NDE.

Application of NDE methods to green ceramics: initial results

International Nuclear Information System (INIS)

Kupperman, D.S.; Karplus, H.B.; Poeppel, R.B.; Ellingson, W.A.; Berger, H.; Robbins, C.; Fuller, E.

1983-01-01

The effectiveness of microradiography, ultrasonic methods, unclear magnetic resonance, and neutron radiography was assessed for the nondestructive evaluation of green (unfired) ceramics. The application of microradiography to ceramics is reviewed, and preliminary experiments with a commercial microradiography unit are described. Conventional ultrasonic techniques are difficult to apply to flaw detection green ceramics because of the high attenuation, fragility, and couplant-absorbing properties of these materials. However, velocity, attenuation, and spectral data were obtained with pressure-coupled transducers and provided useful informaion related to density variations and the presence of agglomerates. Nuclear magnetic resonance (NMR) imaging techniques and neutron radiography were considered for detection of anomalies in the distribution of porosity. With NMR, areas of high porosity might be detected after the samples are doped with water. In the case of neutron radiography, although imaging the binder distribution throughout the sample may not be feasible because of the low overall concentration of binder, regions of high binder concentration (thus high porosity) should be detectable

The state-of-the-art of the established conventional and advanced NDE-techniques and procedures for defect detection and sizing

International Nuclear Information System (INIS)

Crutzen, S.; Edelmann, X.

1988-01-01

This document presents several non-destructive ultrasonic techniques used for the inspection of various welds. Some probes are described and acoustic holography is presented as well as the time-of-flight diffraction (TOFD) technique. The three phases of the Programme for the Inspection of Steel Components (PISC) are described and results of each phase are presented. Eventually, problems related to the examination of austenitic welds are described. Special techniques for the ultrasonic examination of these welds are then presented. (TEC)

The state-of-the-art of the established conventional and advanced NDE-techniques and procedures for defect detection and sizing

Energy Technology Data Exchange (ETDEWEB)

Crutzen, S; Edelmann, X

1988-12-31

This document presents several non-destructive ultrasonic techniques used for the inspection of various welds. Some probes are described and acoustic holography is presented as well as the time-of-flight diffraction (TOFD) technique. The three phases of the Programme for the Inspection of Steel Components (PISC) are described and results of each phase are presented. Eventually, problems related to the examination of austenitic welds are described. Special techniques for the ultrasonic examination of these welds are then presented. (TEC). 24 refs.

assessment of environmental impacts in comfortable furniture production process using life cycle assessment (LCA technique

Directory of Open Access Journals (Sweden)

hejhar abbasi

2016-12-01

Full Text Available Furniture industry releases annually a large amount of volatile organic compound to the environment due to the use of adhesives, textiles, paints and coating materials. There are some different methods to measure the load of pollutions and the environmental impacts. Life cycle assessment (LCA is one of the best techniques. LCA is a technique in which all environmental impacts related to a product assessed all over its life cycle, from cradle to grave, and ultimately can be used to improve the production process and to prevent unsuitable environmental impacts. In summary, it can be concluded that the use of this technique is the basis for sustainable development and improving social, economic, and environmental indices. This study focused on the collecting of a comprehensive life cycle inventory data for comfortable furniture in two different production processes (B1 and B2 located in Tehran province, and analyzed the environmental impacts during the production process as gate to gate investigation. The results revealed that emissions in production process B1 were higher than that of production process B2. The reason for this is that basic operations such as sawing and frame assembling along with final operation have been done in the same unit for case B1. Textile production and usage, and polyurethane foam were identified as the main hotspots, respectively. Moreover, the results showed that comfortable furniture production process has the highest effects on ecosystem quality, human health, and resources (fossil fuels and mines, respectively.

Inverse kinetics technique for reactor shutdown measurement: an experimental assessment. [AGR

Energy Technology Data Exchange (ETDEWEB)

Lewis, T. A.; McDonald, D.

1975-09-15

It is proposed to use the Inverse Kinetics Technique to measure the subcritical reactivity as a function of time during the testing of the nitrogen injection systems on AGRs. A description is given of an experimental assessment of the technique by investigating known transients created by control rod movements on a small experimental reactor, (2m high, 1m radius). Spatial effects were observed close to the moving rods but otherwise derived reactivities were independent of detector position and agreed well with the existing calibrations. This prompted the suggestion that data from installed reactor instrumentation could be used to calibrate CAGR control rods.

Post flooding damage assessment of earth dams and historical reservoirs using non-invasive geophysical techniques

Science.gov (United States)

Sentenac, Philippe; Benes, Vojtech; Budinsky, Vladimir; Keenan, Helen; Baron, Ron

2017-11-01

This paper describes the use of four geophysical techniques to map the structural integrity of historical earth reservoir embankments which are susceptible to natural decay with time. The four techniques that were used to assess the post flood damage were 1. A fast scanning technique using a dipole electromagnetic profile apparatus (GEM2), 2. Electrical Resistivity Tomography (ERT) in order to obtain a high resolution image of the shape of the damaged/seepage zone, 3. Self-Potential surveys were carried out to relate the detected seepage evolution and change of the water displacement inside the embankment, 4. The washed zone in the areas with piping was characterised with microgravimetry. The four geophysical techniques used were evaluated against the case studies of two reservoirs in South Bohemia, Czech Republic. A risk approach based on the Geophysical results was undertaken for the reservoir embankments. The four techniques together enabled a comprehensive non-invasive assessment whereby remedial action could be recommended where required. Conclusions were also drawn on the efficiency of the techniques to be applied for embankments with wood structures.

The Application of Isotope Techniques in Nutrient Assessment and Management in Riverine Systems. Present and Future

Energy Technology Data Exchange (ETDEWEB)

Ito, M.; Newman, B. D. [International Atomic Energy Agency, Isotope Hydrology Section, Vienna (Austria); Hadwen, W. L. [Australian Rivers Institute, Griffith School of Environment, Griffith University - Nathan Campus, Brisbane, Queensland (Australia); Rogers, K. [National Isotope Center, GNS Science, Lower Hutt (New Zealand); Mayer, B. [Department of Geoscience, University of Calgary, Calgary, Alberta (Canada); Hein, T. [Wasser Cluster Lunz, Interuniversitary Center for Aquatic Research, Lunz-See, and University of Natural Resources and Applied Life Sciences, Institute of Hydrobiology and Aquatic Ecosystem Management, Vienna (Austria); Stellato, L. [Centre for Isotopic Research on Cultural and Environmental Heritage (CIRCE), Seconda Universita degli Studi di Napoli, Caserta (Italy); Ohte, N. [Graduate School of Agricultural and Life Sciences, University of Tokyo, Tokyo (Japan); Mclaughlin, K. [Southern California Coastal Water Research Project, Costa Mesa, California (United States)

2013-05-15

A variety of sources contribute to nutrients in rivers and nutrients may subsequently take various pathways and undergo different transformation processes. We first review representative types of isotopes and the roles of isotope techniques that have been or could be used for nutrient assessment and management. We then present technical, financial and logistical matters to be considered in selecting appropriate isotope techniques for nutrient assessment and management. Lastly we propose several approaches on the application of isotope techniques to make more effective the studies and management of nutrients in rivers in the near future. (author)

Monitoring tensile damage evolution in Nextel 312/BlackglasTM composites

International Nuclear Information System (INIS)

Kim, Jeongguk; Liaw, Peter K.

2005-01-01

Tensile damage evolution was monitored with the aid of nondestructive evaluation (NDE) techniques. Several NDE methods, such as ultrasonic testing (UT), infrared (IR) thermography, and acoustic emission (AE) techniques, were employed to analyze damage evolution during tensile testing of Nextel 312/Blackglas TM composites. Prior to tensile testing, UT was used to characterize the initial defect distribution of the samples. During tensile testing, AE sensors and an IR camera were used for in situ monitoring of the progressive damage of the samples. AE provided the amounts of damage evolution in terms of the AE intensity and/or energy, and the IR camera was used to obtain the temperature changes during the test. Microstructural characterization using scanning electron microscopy (SEM) was performed to investigate the fracture mechanisms and modes of Nextel 312/Blackglas TM samples. Moreover, SEM characterization was used to document failure behavior, and to show comparable results with NDE signatures

A Quantitative Needs Assessment Technique for Cross-Cultural Work Adjustment Training.

Science.gov (United States)

Selmer, Lyn

2000-01-01

A study of 67 Swedish expatriate bosses and 104 local Hong Kong middle managers tested a quantitative needs assessment technique measuring work values. Two-thirds of middle managers' work values were not correctly estimated by their bosses, especially instrumental values (pay, benefits, security, working hours and conditions), indicating a need…

The selection of probabilistic safety assessment techniques for non-reactor nuclear facilities

International Nuclear Information System (INIS)

Vail, J.

1992-01-01

Historically, the probabilistic safety assessment (PSA) methodology of choice is the well known event tree/fault tree inductive technique. For reactor facilities is has stood the test of time. Some non-reactor nuclear facilities have found inductive methodologies difficult to apply. The stand-alone fault tree deductive technique has been used effectively to analyze risk in nuclear chemical processing facilities and waste handling facilities. The selection between the two choices suggest benefits from use of the deductive method for non-reactor facilities

Criteria for assessing the quality of signal processing techniques for acoustic leak detection

International Nuclear Information System (INIS)

Prabhakar, R.; Singh, O.P.

1990-01-01

In this paper the criteria used in the first IAEA coordinated research programme to assess the quality of signal processing techniques for sodium boiling noise detection are highlighted. Signal processing techniques, using new features sensitive to boiling and a new approach for achieving higher reliability of detection, which were developed at Indira Gandhi Centre for Atomic Research are also presented. 10 refs, 3 figs, 2 tabs

Performance assessment techniques for groundwater recovery and treatment systems

Energy Technology Data Exchange (ETDEWEB)

Kirkpatrick, G.L. [Environmental Resources Management, Inc., Exton, PA (United States)

1993-03-01

Groundwater recovery and treatment (pump and treat systems) continue to be the most commonly selected remedial technology for groundwater restoration and protection programs at hazardous waste sites and RCRA facilities nationwide. Implementing a typical groundwater recovery and treatment system includes the initial assessment of groundwater quality, characterizing aquifer hydrodynamics, recovery system design, system installation, testing, permitting, and operation and maintenance. This paper focuses on methods used to assess the long-term efficiency of a pump and treat system. Regulatory agencies and industry alike are sensitive to the need for accurate assessment of the performance and success of groundwater recovery systems for contaminant plume abatement and aquifer restoration. Several assessment methods are available to measure the long-term performance of a groundwater recovery system. This paper presents six assessment techniques: degree of compliance with regulatory agency agreement (Consent Order of Record of Decision), hydraulic demonstration of system performance, contaminant mass recovery calculation, system design and performance comparison, statistical evaluation of groundwater quality and preferably, integration of the assessment methods. Applying specific recovery system assessment methods depends upon the type, amount, and quality of data available. Use of an integrated approach is encouraged to evaluate the success of a groundwater recovery and treatment system. The methods presented in this paper are for engineers and corporate management to use when discussing the effectiveness of groundwater remediation systems with their environmental consultant. In addition, an independent (third party) system evaluation is recommended to be sure that a recovery system operates efficiently and with minimum expense.

Reliability of system identification techniques to assess standing balance in healthy elderly

NARCIS (Netherlands)

Pasma, Jantsje H.; Engelhart, Denise; Maier, Andrea B.; Aarts, Ronald G.K.M.; Van Gerven, Joop M.A.; Arendzen, J. Hans; Schouten, Alfred C.; Meskers, Carel G.M.; Van Kooij, Herman Der

2016-01-01

Objectives System identification techniques have the potential to assess the contribution of the underlying systems involved in standing balance by applying well-known disturbances. We investigated the reliability of standing balance parameters obtained with multivariate closed loop system

Reliability of System Identification Techniques to Assess Standing Balance in Healthy Elderly

NARCIS (Netherlands)

Pasma, J.H.; Engelhart, D.; Maier, A.B.; Aarts, R.G.K.M.; Van Gerven, J.M.A.; Arendzen, J.H.; Schouten, A.C.; Meskers, C.G.M.; Van der Kooij, H.

2016-01-01

Objectives System identification techniques have the potential to assess the contribution of the underlying systems involved in standing balance by applying well-known disturbances. We investigated the reliability of standing balance parameters obtained with multivariate closed loop system

Nondestructive materials characterization with applications to aerospace materials

CERN Document Server

Nagy, Peter; Rokhlin, Stanislav

2004-01-01

With an emphasis on aircraft materials, this book describes techniques for the material characterization to detect and quantify degradation processes such as corrosion and fatigue. It introduces readers to these techniques based on x-ray, ultrasonic, optical and thermal principles and demonstrates the potential of the techniques for a wide variety of applications concerning aircraft materials, especially aluminum and titanium alloys. The advantages and disadvantages of various techniques are evaluated. An introductory chapter describes the typical degradation mechanisms that must be considered and the microstructure features that have to be detected by NDE methods. Finally, some approaches for making lifetime predictions are discussed. It is suitable as a textbook in special training courses in advanced NDE and aircraft materials characterization.

KARS İLİNDE ÖRGÜN EĞİTİMİN GELİŞİMİ VE MEVCUT DURUMU

OpenAIRE

DEMİR, MUCİP

2016-01-01

Doğu Anadolu Bölgesinin Kars Erzurum bölümünde yer alan Kars İli ortalama irtifası 2000 metre civarında olan ve birçok yeri volkanik materyallerle örtülü Kars Platosu üzerinde bulunmaktadır. Mevcut topografik koşulların etkisiyle sert karasal iklimin görüldüğü ilde başta nüfus olmak üzere diğer beşeri faaliyetler bu coğrafik faktörlerin yoğun etkisiyle şekillenmektedir. İlde halen 300.000 civarında bulunan nüfus il dışına doğru meydana gelen göçlerle azalış eğilimi göstermektedir.373 ilkokul,...

Systematic comparative and sensitivity analyses of additive and outranking techniques for supporting impact significance assessments

International Nuclear Information System (INIS)

Cloquell-Ballester, Vicente-Agustin; Monterde-Diaz, Rafael; Cloquell-Ballester, Victor-Andres; Santamarina-Siurana, Maria-Cristina

2007-01-01

Assessing the significance of environmental impacts is one of the most important and all together difficult processes of Environmental Impact Assessment. This is largely due to the multicriteria nature of the problem. To date, decision techniques used in the process suffer from two drawbacks, namely the problem of compensation and the problem of identification of the 'exact boundary' between sub-ranges. This article discusses these issues and proposes a methodology for determining the significance of environmental impacts based on comparative and sensitivity analyses using the Electre TRI technique. An application of the methodology for the environmental assessment of a Power Plant project within the Valencian Region (Spain) is presented, and its performance evaluated. It is concluded that contrary to other techniques, Electre TRI automatically identifies those cases where allocation of significance categories is most difficult and, when combined with sensitivity analysis, offers greatest robustness in the face of variation in weights of the significance attributes. Likewise, this research demonstrates the efficacy of systematic comparison between Electre TRI and sum-based techniques, in the solution of assignment problems. The proposed methodology can therefore be regarded as a successful aid to the decision-maker, who will ultimately take the final decision

Fabrication and comparison of PMN-PT single crystal, PZT and PZT-based 1-3 composite ultrasonic transducers for NDE applications.

Science.gov (United States)

Kim, Ki-Bok; Hsu, David K; Ahn, Bongyoung; Kim, Young-Gil; Barnard, Daniel J

2010-08-01

This paper describes fabrication and comparison of PMN-PT single crystal, PZT, and PZT-based 1-3 composite ultrasonic transducers for NDE applications. As a front matching layer between test material (Austenite stainless steel, SUS316) and piezoelectric materials, alumina ceramics was selected. The appropriate acoustic impedance of the backing materials for each transducer was determined based on the results of KLM model simulation. Prototype ultrasonic transducers with the center frequencies of approximately 2.25 and 5MHz for contact measurement were fabricated and compared to each other. The PMN-PT single crystal ultrasonic transducer shows considerably improved performance in sensitivity over the PZT and PZT-based 1-3 composite ultrasonic transducers. Copyright (c) 2010 Elsevier B.V. All rights reserved.

Test plan for suitability assessment of five overcoring stress measurement techniques

International Nuclear Information System (INIS)

Gregory, E.C.; Rundle, T.A.; McCabe, W.M.; Kim, K.

1982-08-01

Tests are to be conducted at the Near-Surface Test Facility (NSTF) to assess the suitability of five overcoring techniques for in situ stress determination in a jointed basalt. The overcoring methods to be investigated use the following instrumentation to measure strain relief by overcoring a pilot borehole: USBM borehole deformation gage, CSIRO hollow inclusion stress cell, cast epoxy inclusion, the Lulea triaxial strain cell and the ''doorstopper'' biaxial strain cell. The tests are to provide data regarding the state of stress below the NSTF. This information is to be used in the evaluation of each method of overcoring. During the course of field testing, an attempt is to be made to adapt conventional overcoring techniques and analytical methods to the basalt medium. If overcoring stress determination in basalt is shown suitable, then additional studies will be identified to further adapt a technique for use at depth. In addition to the five overcoring techniques to be tested at the NSTF, stress measurements by Hydrofracturing are to be conducted to provide data for direct comparison with overcoring results. 16 refs., 18 figs

Assessment of MODIS On-Orbit Calibration Using a Deep Convective Cloud Technique

Science.gov (United States)

Mu, Qiaozhen; Wu, Aisheng; Chang, Tiejun; Angal, Amit; Link, Daniel; Xiong, Xiaoxiong; Doelling, David R.; Bhatt, Rajendra

2016-01-01

The MODerate Resolution Imaging Spectroradiometer (MODIS) sensors onboard Terra and Aqua satellites are calibrated on-orbit with a solar diffuser (SD) for the reflective solar bands (RSB). The MODIS sensors are operating beyond their designed lifetime and hence present a major challenge to maintain the calibration accuracy. The degradation of the onboard SD is tracked by a solar diffuser stability monitor (SDSM) over a wavelength range from 0.41 to 0.94 micrometers. Therefore, any degradation of the SD beyond 0.94 micrometers cannot be captured by the SDSM. The uncharacterized degradation at wavelengths beyond this limit could adversely affect the Level 1B (L1B) product. To reduce the calibration uncertainties caused by the SD degradation, invariant Earth-scene targets are used to monitor and calibrate the MODIS L1B product. The use of deep convective clouds (DCCs) is one such method and particularly significant for the short-wave infrared (SWIR) bands in assessing their long-term calibration stability. In this study, we use the DCC technique to assess the performance of the Terra and Aqua MODIS Collection-6 L1B for RSB 1 3- 7, and 26, with spectral coverage from 0.47 to 2.13 micrometers. Results show relatively stable trends in Terra and Aqua MODIS reflectance for most bands. Careful attention needs to be paid to Aqua band 1, Terra bands 3 and 26 as their trends are larger than 1% during the study time period. We check the feasibility of using the DCC technique to assess the stability in MODIS bands 17-19. The assessment test on response versus scan angle (RVS) calibration shows substantial trend difference for Aqua band 1between different angles of incidence (AOIs). The DCC technique can be used to improve the RVS calibration in the future.

Characteristics of an HTS-SQUID gradiometer with ramp-edge Josephson junctions and its application on robot-based 3D-mobile compact SQUID NDE system

Energy Technology Data Exchange (ETDEWEB)

Hatsukade, Y., E-mail: hatukade@ens.tut.ac.jp [Toyohashi University of Technology, 1-1 Hibarigaoka, Tempaku-cho, Toyohashi, Aichi 441-8580 (Japan); Hayashi, K.; Shinyama, Y.; Kobayashi, Y. [Toyohashi University of Technology, 1-1 Hibarigaoka, Tempaku-cho, Toyohashi, Aichi 441-8580 (Japan); Adachi, S.; Tanabe, K. [International Superconductivity Technology Center/Superconductivity Research Laboratory, 10-13, Shinonome 1-chome, Koto-ku, Tokyo 135-0062 (Japan); Tanaka, S. [Toyohashi University of Technology, 1-1 Hibarigaoka, Tempaku-cho, Toyohashi, Aichi 441-8580 (Japan)

2011-11-15

We investigated behavior of HTS-dc-SQUID gradiometers with ramp-edge Josephson junctions (JJs) in ac and dc magnetic fields. In the both fields, the gradiometers show higher durability against entry of flux vortices than SQUIDs with bicrystal JJs. A robot-based SQUID NDE system utilizing the gradiometer was developed in an unshielded environment. Detectability of the system to detect non-through cracks in double-layer structures was demonstrated. A new excitation coil was applied to detect cracks that oriented vertical and parallel to the baseline of the gradiometer. In this paper, we investigated detailed behavior of novel HTS-dc-SQUID gradiometers with ramp-edge Josephson junctions (JJs) in both an ac magnetic field and a dc magnetic field. In the both fields, the novel gradiometers shows the superior performance to the conventional YBa{sub 2}Cu{sub 3}O{sub 7-x} (YBCO) HTS-dc-SQUID gradiometer and a bare HTS-dc-SQUID ring with bicrystal JJs concerning durability against entry and hopping of flux vortices, probably due to their differential pickup coils without a grain boundary and multilayer structure of the ramp-edge JJs. A robot-based compact HTS-SQUID NDE system utilizing the novel gradiometer was reviewed, and detectability of the system to detect non-through cracks in a carbon fiber reinforced plastic (CFRP)/Al double-layer structure was demonstrated. A new excitation coil in which the supplied currents flowed in the orthogonal directions was applied to detect cracks that oriented vertical and parallel to the baseline of the gradiometer.

Formative Assessment and the Intuitive Incorporation of Research-Based Instruction Techniques

Science.gov (United States)

Kuiper, Paula; VanOeffelen, Rachel; Veldkamp, Simon; Bokma, Isaac; Breems, Luke; Fynewever, Herb

2015-01-01

Using Max Weber's theory of ideal types, the authors classify the formative assessment techniques used by 12 college instructors. Their data reveal two pairs of opposing preferences: (1) highly preplanned vs. highly emergent and (2) focused on individual students vs. focused on the class as a whole. Using interview data, they illustrate how each…

Reality of near-death-experience memories: Evidence from a psychodynamic and electrophysiological integrated study

Directory of Open Access Journals (Sweden)

Arianna ePalmieri

2014-06-01

Full Text Available The nature of near-death experiences (NDEs is largely unknown but recent evidence suggests the intriguing possibility that NDEs may refer to actually perceived, and stored, experiences (although not necessarily in relation to the external physical world. We adopted an integrated approach involving a hypnosis-based clinical protocol to improve recall and decrease memory inaccuracy together with Electroencephalography (EEG recording in order to investigate the characteristics of NDE memories and their neural markers compared to memories of both real and imagined events. We included 10 participants with NDEs, defined by the Greyson NDE scale, and 10 control subjects without NDE. Memories were assessed using the Memory Characteristics Questionnaire.Our hypnosis-based protocol increased the amount of details in the recall of all kind of memories considered (NDE, real, and imagined events. Findings showed that NDE memories were similar to real memories in terms of detail richness, self-referential, and emotional information. Moreover, NDE memories were significantly different from memories of imagined events. The pattern of EEG results indicated that real memories recall was positively associated with two memory-related frequency bands, i.e., high alpha and gamma. NDE memories were linked with theta band, a well-known marker of episodic memory. The recall of NDE memories was also related to delta band, which indexes processes such as the recollection of the past, as well as trance states, hallucinations, and other related portals to transpersonal experience. It is notable that the EEG pattern of correlations for NDE memories recall differed from the pattern for memories of imagined events. In conclusion, our findings suggest that, at a phenomenological level, NDE memories cannot be considered equivalent to imagined memories, and at a neural level, NDE memories are stored as episodic memories of events experienced in a peculiar state of consciousness.

Ultrasonic techniques for quality assessment of ITER Divertor plasma facing component

International Nuclear Information System (INIS)

Martinez-Ona, Rafael; Garcia, Monica; Medrano, Mercedes

2009-01-01

The divertor is one of the most challenging components of ITER machine. Its plasma facing components contain thousands of joints that should be assessed to demonstrate their integrity during the required lifetime. Ultrasonic (US) techniques have been developed to study the capability of defect detection and to control the quality and degradation of these interfaces after the manufacturing process. Three types of joints made of carbon fibre composite to copper alloy, tungsten to copper alloy, and copper-to-copper alloy with two types of configurations have been studied. More than 100 samples representing these configurations and containing implanted flaws of different sizes have been examined. US techniques developed are detailed and results of validation samples examination before and after high heat flux (HHF) tests are presented. The results show that for W monoblocks the US technique is able to detect, locate and size the degradations in the two sample joints; for CFC monoblocks, the US technique is also able to detect, locate and size the calibrated defects in the two joints before the HHF, however after the HHF test the technique is not able to reliably detect defects in the CFC/Cu joint; finally, for the W flat tiles the US technique is able to detect, locate and size the calibrated defects in the two joints before HHF test, nevertheless defect location and sizing are more difficult after the HHF test.

Uncertainty in safety : new techniques for the assessment and optimisation of safety in process industry

NARCIS (Netherlands)

Rouvroye, J.L.; Nieuwenhuizen, J.K.; Brombacher, A.C.; Stavrianidis, P.; Spiker, R.Th.E.; Pyatt, D.W.

1995-01-01

At this moment there is no standardised method for the assessment for safety in the process industry. Many companies and institutes use qualitative techniques for safety analysis while other companies and institutes use quantitative techniques. The authors of this paper will compare different

Alzheimer's Disease Assessment: A Review and Illustrations Focusing on Item Response Theory Techniques.

Science.gov (United States)

Balsis, Steve; Choudhury, Tabina K; Geraci, Lisa; Benge, Jared F; Patrick, Christopher J

2018-04-01

Alzheimer's disease (AD) affects neurological, cognitive, and behavioral processes. Thus, to accurately assess this disease, researchers and clinicians need to combine and incorporate data across these domains. This presents not only distinct methodological and statistical challenges but also unique opportunities for the development and advancement of psychometric techniques. In this article, we describe relatively recent research using item response theory (IRT) that has been used to make progress in assessing the disease across its various symptomatic and pathological manifestations. We focus on applications of IRT to improve scoring, test development (including cross-validation and adaptation), and linking and calibration. We conclude by describing potential future multidimensional applications of IRT techniques that may improve the precision with which AD is measured.

Available techniques for objective assessment of upper airway narrowing in snoring and sleep apnea

DEFF Research Database (Denmark)

Faber, Christian; Grymer, Luisa

2003-01-01

positive airway pressure during sleep, fluoroscopy, CT scanning, MR scanning, manometry, and acoustic reflections. Data from different studies using various methods suggest that different patients have different patterns of narrowing or collapse of the pharynx. No reference standard exists...... option for different patients. This article lists criteria that must be used to assess the available techniques for diagnosis of obstruction level in snoring and OSAHS. The advantages and limitations of each diagnostic technique are summarized, with emphasis on the acoustic reflectometry technique....

Assessment of dye distribution in sensitized solar cells by microprobe techniques

Energy Technology Data Exchange (ETDEWEB)

Barreiros, M.A., E-mail: alexandra.barreiros@lneg.pt [Laboratório Nacional de Energia e Geologia, LEN/UES, Estrada do Paço do Lumiar, 22, 1649-038 Lisboa (Portugal); Corregidor, V. [IPFN, Instituto Superior Técnico, Universidade de Lisboa, E.N. 10, 2686-953 Sacavém (Portugal); Alves, L.C. [C2TN, Campus Tecnológico e Nuclear, Instituto Superior Técnico, Universidade de Lisboa, E.N. 10, 2686-953 Sacavém (Portugal); Guimarães, F. [Laboratório Nacional de Energia e Geologia, LGM/UCTM, Rua da Amieira, Apartado 1089, 4466-901 S. Mamede de Infesta (Portugal); Mascarenhas, J.; Torres, E.; Brites, M.J. [Laboratório Nacional de Energia e Geologia, LEN/UES, Estrada do Paço do Lumiar, 22, 1649-038 Lisboa (Portugal)

2015-04-01

Dye sensitized solar cells (DSCs) have received considerable attention once this technology offers economic and environmental advantages over conventional photovoltaic (PV) devices. The PV performance of a DSC relies on the characteristics of its photoanode, which typically consists of a nanocrystalline porous TiO{sub 2} film, enabled with a large adsorptive surface area. Dye molecules that capture photons from light during device operation are attached to the film nanoparticles. The effective loading of the dye in the TiO{sub 2} electrode is of paramount relevance for controlling and optimizing solar cell parameters. Relatively few methods are known today for quantitative evaluation of the total dye adsorbed on the film. In this context, microprobe techniques come out as suitable tools to evaluate the dye surface distribution and depth profile in sensitized films. Electron Probe Microanalysis (EPMA) and Ion Beam Analytical (IBA) techniques using a micro-ion beam were used to quantify and to study the distribution of the Ru organometallic dye in TiO{sub 2} films, making use of the different penetration depth and beam sizes of each technique. Different 1D nanostructured TiO{sub 2} films were prepared, morphologically characterized by SEM, sensitized and analyzed by the referred techniques. Dye load evaluation in different TiO{sub 2} films by three different techniques (PIXE, RBS and EPMA/WDS) provided similar results of Ru/Ti mass fraction ratio. Moreover, it was possible to assess dye surface distribution and its depth profile, by means of Ru signal, and to visualize the dye distribution in sample cross-section through X-ray mapping by EPMA/EDS. PIXE maps of Ru and Ti indicated an homogeneous surface distribution. The assessment of Ru depth profile by RBS showed that some films have homogeneous Ru depth distribution while others present different Ru concentration in the top layer (2 μm thickness). These results are consistent with the EPMA/EDS maps obtained.

The development and use of parametric sampling techniques for probabilistic risk assessment

International Nuclear Information System (INIS)

Dalrymple, G.J.; Broyd, T.W.

1987-01-01

In order to enable evaluation to be made of proposals for the underground disposal of low and intermediate level radioactive wastes in the United Kingdom, the Department of the Environment (DoE) research programme includes development of computer-based methods for use in a multistage assessment process. To test the adequacy of the various methods of data acquisitions and radiological assessment a mock assessment exercise is currently being conducted by the department. This paper outlines the proposed methodology which provides for the use of probabilistic modelling based upon the Atomic Energy of Canada Ltd SYVAC variability analysis approach using new models (SYVAC 'A') and data appropriate to UK conditions for a deep horizontal tunnel repository concept. This chapter describes the choice of a suitable technique for the sampling of data input to the SYVAC 'A' model and techniques for analysing the predictions of dose and risk made by the model. The sensitivity of the model predictions (risk and dose to man) to the input parameters was compared for four different methods. All four methods identified the same geological parameters as the most important. (author)

Assessment of endocrine disorders of the hypothalamic-pituitary axis by nuclear medicine techniques

International Nuclear Information System (INIS)

Schmidt, M.; Theissen, P.; Dietlein, M.; Schicha, H.; Jackenhoevel, F.; Krone, W.

2002-01-01

The following article reviews nuclear medicine techniques which can be used for assessment of endocrine disorders of the hypothalamic-pituitary axis. For planar and SPECT imaging somatostatin-receptor- and dopamine-D2-receptor-scintigraphy are the most widely distributed techniques. These nuclear medicine techniques may be indicated in selected cases to answer differential diagnostic problems. They can be helpful to search for presence and localization of receptor positive tissue. Furthermore they can detect metastasis in the rare cases of a pituitary carcinoma. Scintigraphy with Gallium-67 is suitable for further diagnostic evaluation in suspected hypophysitis. Other SPECT radiopharmaca do not have relevant clinical significance. F-18-FDG as PET radiopharmacon is not ideal because obvious pituitary adenomas could not be visualized. Other PET radiopharmaca including C-11-methionine, C-11-tyrosine, F-18-fluoroethylspiperone, C-11-methylspiperone, and C-11-raclopride are available in specialized centers only. Overall indications for nuclear medicine in studies for the assessment of endocrine disorders of the hypothalamic-pituitary-axis are rare. Original studies often report only about a small number of patients. According to the authors' opinion the relevance of nuclear medicine in studies of clinically important endocrinologic fields, e. g. localization of small ACTH-producing pituitary adenomas, tumor localization in ectopic ACTH syndrome, localization of recurrent pituitary tissue, assessment of small incidentalomas, can not be definitely given yet. (orig.) [de

Waste inspection tomography (WIT)

Energy Technology Data Exchange (ETDEWEB)

Bernardi, R.T. [Bio-Imaging Research, Inc., Lincolnshire, IL (United States)

1995-10-01

Waste Inspection Tomography (WIT) provides mobile semi-trailer mounted nondestructive examination (NDE) and assay (NDA) for nuclear waste drum characterization. WIT uses various computed tomography (CT) methods for both NDE and NDA of nuclear waste drums. Low level waste (LLW), transuranic (TRU), and mixed radioactive waste can be inspected and characterized without opening the drums. With externally transmitted x-ray NDE techniques, WIT has the ability to identify high density waste materials like heavy metals, define drum contents in two- and three-dimensional space, quantify free liquid volumes through density and x-ray attenuation coefficient discrimination, and measure drum wall thickness. With waste emitting gamma-ray NDA techniques, WIT can locate gamma emitting radioactive sources in two- and three-dimensional space, identify gamma emitting, isotopic species, identify the external activity levels of emitting gamma-ray sources, correct for waste matrix attenuation, provide internal activity approximations, and provide the data needed for waste classification as LLW or TRU.

Computed tomography of human joints and radioactive waste drums

International Nuclear Information System (INIS)

Martz, Harry E.; Roberson, G. Patrick; Hollerbach, Karin; Logan, Clinton M.; Ashby, Elaine; Bernardi, Richard

1999-01-01

X- and gamma-ray imaging techniques in nondestructive evaluation (NDE) and assay (NDA) have seen increasing use in an array of industrial, environmental, military, and medical applications. Much of this growth in recent years is attributed to the rapid development of computed tomography (CT) and the use of NDE throughout the life-cycle of a product. Two diverse examples of CT are discussed, 1.) Our computational approach to normal joint kinematics and prosthetic joint analysis offers an opportunity to evaluate and improve prosthetic human joint replacements before they are manufactured or surgically implanted. Computed tomography data from scanned joints are segmented, resulting in the identification of bone and other tissues of interest, with emphasis on the articular surfaces. 2.) We are developing NDE and NDA techniques to analyze closed waste drums accurately and quantitatively. Active and passive computed tomography (A and PCT) is a comprehensive and accurate gamma-ray NDA method that can identify all detectable radioisotopes present in a container and measure their radioactivity

Waste inspection tomography (WIT)

International Nuclear Information System (INIS)

Bernardi, R.T.

1995-01-01

Waste Inspection Tomography (WIT) provides mobile semi-trailer mounted nondestructive examination (NDE) and assay (NDA) for nuclear waste drum characterization. WIT uses various computed tomography (CT) methods for both NDE and NDA of nuclear waste drums. Low level waste (LLW), transuranic (TRU), and mixed radioactive waste can be inspected and characterized without opening the drums. With externally transmitted x-ray NDE techniques, WIT has the ability to identify high density waste materials like heavy metals, define drum contents in two- and three-dimensional space, quantify free liquid volumes through density and x-ray attenuation coefficient discrimination, and measure drum wall thickness. With waste emitting gamma-ray NDA techniques, WIT can locate gamma emitting radioactive sources in two- and three-dimensional space, identify gamma emitting, isotopic species, identify the external activity levels of emitting gamma-ray sources, correct for waste matrix attenuation, provide internal activity approximations, and provide the data needed for waste classification as LLW or TRU

Tree Simulation Techniques for Integrated Safety Assessment

International Nuclear Information System (INIS)

Melendez Asensio, E.; Izquierdo Rocha, J.M.; Sanchez Perez, M.; Hortal Reymundo, J.; Perez Mulas, A.

1999-01-01

techniques are: (a) An unifying theory that should (i) establish the relationship among different approaches and, in particular, be able to demonstrate the standard safety assessment approach as a particular case, (ii) identify implicit assumptions in present practice and (iii) establish a sound scientific reference for an ideal treatment in order to judge the relative importance of implicit and explicit assumptions. In addition, the theoretical developments help to identify the type of applications where the new developments will be a necessary requirement. (b) The capability for simulation of trees. By this we mean the techniques required to be able to efficiently simulate all branches. Historically algorithms able to do this were already implemented in earlier pioneering work for discrete number of branches while stochastic branching requires Montecarlo techniques. (c) The capability to incorporate new types of branching, particularly operator actions. This paper shortly reviews these aspects and justifies in that frame our particular development, denoted here as Integrated Safety Assessment methodology. In this method, the dynamics of the event is followed by transient simulation in tree form, building a Setpoint or Deterministic Dynamic Event Tree (DDET). When a setpoint that should trigger the actuation of a protection is crossed, the tree is opened in branches corresponding to different functioning states of the protection device and each branch followed by the engineering simulator. One of these states is the nominal state, which, in the PSAs, is Associated to the success criterion of the system

Korean round-robin result for new international program to assess the reliability of emerging nondestructive techniques

Energy Technology Data Exchange (ETDEWEB)

Kim, Kyung Cho; Kim, Jin Gyum; Kang, Sung Sik; Jhung, Myung Jo [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

2017-04-15

The Korea Institute of Nuclear Safety, as a representative organization of Korea, in February 2012 participated in an international Program to Assess the Reliability of Emerging Nondestructive Techniques initiated by the U.S. Nuclear Regulatory Commission. The goal of the Program to Assess the Reliability of Emerging Nondestructive Techniques is to investigate the performance of emerging and prospective novel nondestructive techniques to find flaws in nickel-alloy welds and base materials. In this article, Korean round-robin test results were evaluated with respect to the test blocks and various nondestructive examination techniques. The test blocks were prepared to simulate large-bore dissimilar metal welds, small-bore dissimilar metal welds, and bottom-mounted instrumentation penetration welds in nuclear power plants. Also, lessons learned from the Korean round-robin test were summarized and discussed.

A Preliminary Investigation of General and Technique-specific Assessments for the Evaluation of Laparoscopic Technical Skills.

Science.gov (United States)

Vergis, Ashley; Steigerwald, Sarah

2017-10-07

Background  Both general and technique-specific assessments of technical skill have been validated in surgical education. The purpose of this study was to assess the correlation between the objective structured assessment of technical skills (OSATS) and the global operative assessment of laparoscopic skills (GOALS) rating scales using a high-fidelity porcine laparoscopic cholecystectomy model. Methods Post-graduate year-one general surgery and urology residents (n=14) performed a live laparoscopic porcine cholecystectomy. Trained surgeons rated their performance using OSATS and GOALS assessment scales. Results Pearson's correlation coefficient between OSATS and GOALS was 0.96 for overall scores. It ranged from 0.78 - 0.89 for domains that overlapped between the two scales. Conclusion There is a very high correlation between OSATS and GOALS. This implies that they likely measure similar constructs and that either may be used for summative-type assessments of trainee skill. However, further investigation is needed to determine if technique-specific assessments may provide more useful feedback in formative evaluation.

RAIN VOLLEY APPLICATIONS IN UŞAK AND ITS SURROUNDINGS (EXAMLE OF TAKMAK VILLAGE UŞAK VE ÇEVRESİNDE YAĞMUR YAĞDIRMA UYGULAMALARI (TAKMAK KÖYÜ ÖRNEĞİ

Directory of Open Access Journals (Sweden)

Sami KILIÇ

2011-01-01

Full Text Available Every society whose livelyhood is based on agriculture and livestock has developed a kind of belief and application around its culture so as to resolve drought, and people have applied these methods till present time and they stil continue them. In societies, for the rain volley applications, some terms of magic of the rain and prayer of rain have been used. Although there are some magical applications among them, this pratice is generally called as the prayer of rain in Turkish culture.As the livelihood of the people in Takmak village, Eşme, a town of Uşak is based on agriculture and livestock, some practices are held during the drought seasons. The subject of the article is based on description and analysis of the techniques of the rain volley applications today in Takmak village. That’s why, important phenomenons of description data applications of the rain volley applications in Takmak village gained with participant observation and detailed interview technques will be evaluated in terms of History of Religions and the history of the rain volley applications in this village will be put forward with their religious origins. Geçim kaynağı tarım ve hayvancılığa dayanan her toplum, kuraklığı gidermek amacıyla kendi kültürü çevresinde birtakım inanış ve uygulamalar geliştirmiş, bunları geçmişten günümüze kadar uygulamış, halen de uygulamaya devam etmektedir. Toplumlarda, yağmur yağdırma uygulamaları için yağmur büyüsü ve yağmur duası terimleri kullanılmaktadır. Türk kültüründe ise bu işlemlere, içerisinde birtakım büyüsel ve sihirsel uygulamalar bulundurmakla birlikte, genel olarak yağmur duası denilmektedir.Uşak ili Eşme ilçesine bağlı olan Takmak köyünde halkın geçim kaynağı genel olarak tarım ve hayvancılık olması sebebiyle, mevsimin kurak gittiği dönemlerde, yağmur yağdırmak için birtakım pratikler yapılmaktadır. Makalenin konusunu, günümüzde Takmak köyünde

Application of fisheries management techniques to assessing impacts: task I report. [Assessment of chemical, radiological, and thermal impacts of nuclear power plants on fish populations

Energy Technology Data Exchange (ETDEWEB)

McKenzie, D.H.; Baker, K.S.; Fickeisen, D.H.; Metzger, R.M.; Skalski, J.R.

1979-03-01

Task I efforts examined the available fisheries management techniques and assessed their potential application in a confirmatory monitoring program. The objective of such monitoring programs is to confirm that the prediction of an insignificant impact (usually made in the FES) was correct. Fisheries resource managers have developed several tools for assessing the fish population response to stress (exploitation) and they were thought potentially useful for detecting nuclear power plant impacts. Techniques in three categories were examined; catch removal, population dynamics, and nondestructive censuses, and the report contains their description, examples of application, advantages, and disadvantages. The techniques applied at nuclear power plant sites were examined in detail to provide information on implementation and variability of specific approaches. The most suitable techniques to incorporate into a monitoring program confirming no impact appear to be those based on Catch Per Unity Effort (CPUE) and hydroacoustic data. In some specific cases, age and growth studies and indirect census techniques may be beneficial. Recommendations for task II efforts to incorporate these techniques into monitoring program designs are presented. These include development of guidelines for; (1) designing and implementing a data collection program; (2) interpreting these data and assessing the occurrence of impact, and (3) establishment of the monitoring program's ability to detect changes in the affected populations.

Tiit Kask, Aldur Vunk (Hrsg.): Reis (nõukogude) läände / Journey to the [Soviet] west. Kuurortlinn Pärnu 1940-88. Artiklite kogumik / Resort town of Pärnu 1940-88. Collection of articles, Pärnu: Pärnu Linnavalitsus 2009, 121 S., 97 Abb. / Andr

Index Scriptorium Estoniae

Fülberth, Andreas

2011-01-01

Raamatuarvustus: Reis (nõukogude) läände : kuurortlinn Pärnu 1940-88 : artiklite kogumik = Journey to the [Soviet] West : resort town of Pärnu during 1940-88 : collection of articles. Pärnu, 2009

Development of nondestructive evaluation methods for ceramic coatings

International Nuclear Information System (INIS)

Ellingson, W. A.; Deemer, C.; Sun, J. G.; Erdman, S.; Muliere, D.; Wheeler, B.

2002-01-01

Various nondestructive evaluation (NDE) technologies are being developed to study the use of ceramic coatings on components in the hot-gas path of advanced low-emission gas-fired turbines. The types of ceramic coatings include thermal barrier coatings (TBCs) and environmental barrier coatings (EBCs). TBCs are under development for vanes, blades, and combustor liners to allow hotter gas-path temperatures, and EBCs are under development to reduce environmental damage to high-temperature components made of ceramic matrix composites. The NDE methods will be used to (a) provide data to assess the reliability of new coating application processes, (b) identify defective components that could cause unscheduled outages, (c) track growth rates of defects during component use in engines, and (d) allow rational judgment for replace/repair/re-use decisions regarding components. Advances in TBC application, both electron beam-physical vapor deposition (EB-PVD) and air plasma spraying (APS), are allowing higher temperatures in the hot-gas path. However, as TBCs become ''prime reliant,'' their condition at scheduled or unscheduled outages must be known. NDE methods are under development to assess the condition of the TBC for pre-spall conditions. EB-PVD test samples with up to 70 thermal cycles have been studied by a newly developed method involving polarized laser back-scatter NDE. Results suggest a correlation between the NDE laser data and the TBC/bond-coat topography. This finding is important because several theories directed toward understanding the pre-spall condition suggest that the topography in the thermally grown oxide layer changes significantly as a function of the number of thermal cycles. Tests have also been conducted with this NDE method on APS TBCs. Results suggest that the pre-spall condition is detected for these coatings. One-sided, high-speed thermal imaging also has shown promise for NDE of APS coatings. Testing of SiC/SiC composites for combustor liners

A study on hybrid split-spectrum processing technique for enhanced reliability in ultrasonic signal analysis

International Nuclear Information System (INIS)

Huh, Hyung; Koo, Kil Mo; Cheong, Yong Moo; Kim, G. J.

1995-01-01

Many signal-processing techniques have been found to be useful in ultrasonic and nondestructive evaluation. Among the most popular techniques are signal averaging, spatial compounding, matched filters, and homomorphic processing. One of the significant new process is split-spectrum processing(SSP), which can be equally useful in signal-to-noise ratio(SNR) improvement and grain characterization in several engineering materials. The purpose of this paper is to explore the utility of SSP in ultrasonic NDE. A wide variety of engineering problems are reviewed and suggestions for implementation of the technique are provided. SSP uses the frequency-dependent response of the interfering coherent noise produced by unresolvable scatters in the resolution range cell of a transducer. It is implemented by splitting the Sequency spectrum of the received signal by using Gaussian bandpass filters. The theoretical basis for the potential of SSP for grain characterization in SUS 304 material is discussed, and some experimental-evidence for the feasibility of the approach is presented. Results of SNR enhancement in signals obtained from real four samples of SUS 304. The influence of various processing parameters on the performance of the processing technique is also discussed. The minimization algorithm. which provides an excellent SNR enhancement when used either in conjunction with other SSP algorithms like polarity-check or by itself, is also presented.

A Study on Hybrid Split-Spectrum Processing Technique for Enhanced Reliability in Ultrasonic Signal Analysis

International Nuclear Information System (INIS)

Huh, H.; Koo, K. M.; Kim, G. J.

1996-01-01

Many signal-processing techniques have been found to be useful in ultrasonic and nondestructive evaluation. Among the most popular techniques are signal averaging, spatial compounding, matched filters and homomorphic processing. One of the significant new process is split-spectrum processing(SSP), which can be equally useful in signal-to-noise ratio(SNR) improvement and grain characterization in several specimens. The purpose of this paper is to explore the utility of SSP in ultrasonic NDE. A wide variety of engineering problems are reviewed, and suggestions for implementation of the technique are provided. SSP uses the frequency-dependent response of the interfering coherent noise produced by unresolvable scatters in the resolution range cell of a transducer. It is implemented by splitting the frequency spectrum of the received signal by using gaussian bandpass filter. The theoretical basis for the potential of SSP for grain characterization in SUS 304 material is discussed, and some experimental evidence for the feasibility of the approach is presented. Results of SNR enhancement in signals obtained from real four samples of SUS 304. The influence of various processing parameters on the performance of the processing technique is also discussed. The minimization algorithm, which provides an excellent SNR enhancement when used either in conjunction with other SSP algorithms like polarity-check or by itself, is also presented

Multicriteria-based decision aiding technique for assessing energy policy elements-demonstration to a case in Bangladesh

International Nuclear Information System (INIS)

Rahman, Md. Mizanur; Paatero, Jukka V.; Lahdelma, Risto; Wahid, Mazlan A.

2016-01-01

Highlights: • A multicriteria technique for assessing energy policy elements has been proposed. • Energy policy elements have been examined based on assigned criteria. • This assessment gives results which are representative of all stakeholders. • Policy elements which are chosen by this method promote sustainability. - Abstract: The adverse environmental consequences and diminishing trend of fossil fuel reserves indicate a serious need for vibrant and judicious energy policy. Energy policy involves a number of stakeholders, and needs to incorporate the interests and requirements of all the key stakeholder groups. This paper presents a methodological technique to assist with formulating, evaluating, and promoting the energy policy of a country in a transparent and representative way with clear scientific justifications and balanced assessments. The multicriteria decision analysis approach has been a widely used technique for evaluating different alternatives based on the interests of a multitude of stakeholders, and goals. This paper utilizes the SMAA (Stochastic Multicriteria Acceptability Analysis) tool, which can evaluate different alternatives by incorporating multiple criteria, in order to examine the preferences of different policy elements. We further extend this technique by incorporating the LEAP model (Long-range Energy Alternatives Planning system) to assess the emission impacts of different policy elements. We demonstrate the application of this evaluation technique by an analysis of four hypothetical policy elements namely Business-as usual (BAU), Renewables (REN), Renewable-biomass only (REN-b), and Energy conservation and efficient technologies (ECET). These are applied to the case of sharing fuel sources for power generation for the Bangladesh power sector. We found that the REN-b and REN policy elements were the best and second best alternatives with 41% and 32% acceptability respectively. This technique gives transparent information for

Roadmap for Nondestructive Evaluation of Reactor Pressure Vessel Research and Development by the Light Water Reactor Sustainability Program

Energy Technology Data Exchange (ETDEWEB)

Smith, Cyrus M [ORNL; Nanstad, Randy K [ORNL; Clayton, Dwight A [ORNL; Matlack, Katie [Georgia Institute of Technology; Ramuhalli, Pradeep [Pacific Northwest National Laboratory (PNNL); Light, Glenn [Southwest Research Institute, San Antonio

2012-09-01

The Department of Energy s (DOE) Light Water Reactor Sustainability (LWRS) Program is a five year effort which works to develop the fundamental scientific basis to understand, predict, and measure changes in materials and systems, structure, and components as they age in environments associated with continued long-term operations of existing commercial nuclear power reactors. This year, the Materials Aging and Degradation (MAaD) Pathway of this program has placed emphasis on emerging Non-Destructive Evaluation (NDE) methods which support these objectives. DOE funded Research and Development (R&D) on emerging NDE techniques to support commercial nuclear reactor sustainability is expected to begin next year. This summer, the MAaD Pathway invited subject matter experts to participate in a series of workshops which developed the basis for the research plan of these DOE R&D NDE activities. This document presents the results of one of these workshops which are the DOE LWRS NDE R&D Roadmap for Reactor Pressure Vessels (RPV). These workshops made a substantial effort to coordinate the DOE NDE R&D with that already underway or planned by the Electric Power Research Institute (EPRI) and the Nuclear Regulatory Commission (NRC) through their representation at these workshops.

Model assessment using a multi-metric ranking technique

Science.gov (United States)

Fitzpatrick, P. J.; Lau, Y.; Alaka, G.; Marks, F.

2017-12-01

Validation comparisons of multiple models presents challenges when skill levels are similar, especially in regimes dominated by the climatological mean. Assessing skill separation will require advanced validation metrics and identifying adeptness in extreme events, but maintain simplicity for management decisions. Flexibility for operations is also an asset. This work postulates a weighted tally and consolidation technique which ranks results by multiple types of metrics. Variables include absolute error, bias, acceptable absolute error percentages, outlier metrics, model efficiency, Pearson correlation, Kendall's Tau, reliability Index, multiplicative gross error, and root mean squared differences. Other metrics, such as root mean square difference and rank correlation were also explored, but removed when the information was discovered to be generally duplicative to other metrics. While equal weights are applied, weights could be altered depending for preferred metrics. Two examples are shown comparing ocean models' currents and tropical cyclone products, including experimental products. The importance of using magnitude and direction for tropical cyclone track forecasts instead of distance, along-track, and cross-track are discussed. Tropical cyclone intensity and structure prediction are also assessed. Vector correlations are not included in the ranking process, but found useful in an independent context, and will be briefly reported.

The development of an audit technique to assess the quality of safety barrier management

International Nuclear Information System (INIS)

Guldenmund, Frank; Hale, Andrew; Goossens, Louis; Betten, Jeroen; Duijm, Nijs Jan

2006-01-01

This paper describes the development of a management model to control barriers devised to prevent major hazard scenarios. Additionally, an audit technique is explained that assesses the quality of such a management system. The final purpose of the audit technique is to quantify those aspects of the management system that have a direct impact on the reliability and effectiveness of the barriers and, hence, the probability of the scenarios involved. First, an outline of the management model is given and its elements are explained. Then, the development of the audit technique is described. Because the audit technique uses actual major hazard scenarios and barriers within these as its focus, the technique achieves a concreteness and clarity that many other techniques often lack. However, this strength is also its limitation, since the full safety management system is not covered with the technique. Finally, some preliminary experiences obtained from several test sites are compiled and discussed

The development of an audit technique to assess the quality of safety barrier management

Energy Technology Data Exchange (ETDEWEB)

Guldenmund, Frank [Safety Science Group, Delft University of Technology (Netherlands)]. E-mail: f.w.guldenmund@tbm.tudelft.nl; Hale, Andrew [Safety Science Group, Delft University of Technology (Netherlands); Goossens, Louis [Safety Science Group, Delft University of Technology (Netherlands); Betten, Jeroen [Safety Science Group, Delft University of Technology (Netherlands); Duijm, Nijs Jan [Riso National Laboratory (Denmark)

2006-03-31

This paper describes the development of a management model to control barriers devised to prevent major hazard scenarios. Additionally, an audit technique is explained that assesses the quality of such a management system. The final purpose of the audit technique is to quantify those aspects of the management system that have a direct impact on the reliability and effectiveness of the barriers and, hence, the probability of the scenarios involved. First, an outline of the management model is given and its elements are explained. Then, the development of the audit technique is described. Because the audit technique uses actual major hazard scenarios and barriers within these as its focus, the technique achieves a concreteness and clarity that many other techniques often lack. However, this strength is also its limitation, since the full safety management system is not covered with the technique. Finally, some preliminary experiences obtained from several test sites are compiled and discussed.

Feasibility, Reproducibility, and Agreement between Different Speckle Tracking Echocardiographic Techniques for the Assessment of Longitudinal Deformation

Directory of Open Access Journals (Sweden)

Sergio Buccheri

2013-01-01

Full Text Available Background. Left ventricular (LV longitudinal deformation can be assessed with new echocardiographic techniques like triplane echocardiography (3PE and four-dimensional echocardiography (4DE. We aimed to assess the feasibility, reproducibility, and agreement between these different speckle-tracking techniques for the assessment of longitudinal deformation. Methods. 101 consecutive subjects underwent echocardiographic examination. 2D cine loops from the apical views, a triplane view, and an LV 4D full volume were acquired in all subjects. LV longitudinal strain was obtained for each imaging modality. Results. 2DE analysis of LV strain was feasible in 90/101 subjects, 3PE strain in 89/101, and 4DE strain in 90/101. The mean value of 2DE and 3PE longitudinal strains was significantly higher with respect to 4DE. The relationship between 2DE and 3PE derived strains (r=0.782 was significantly higher (z=3.72, P<0.001 than that between 2DE and 4DE (r=0.429 and that between 3PE and 4DE (r=0.510; z=3.09, P=0.001. The mean bias between 2DE and 4DE strains was -6.61±7.31% while -6.42±6.81% between 3PE and 4DE strains; the bias between 2DE and 3PE strain was of 0.21±4.16%. Intraobserver and interobserver variabilities were acceptable among the techniques. Conclusions. Echocardiographic techniques for the assessment of longitudinal deformation are not interchangeable, and further studies are needed to assess specific reference values.

Captions, Consistency, Creativity, and the Consensual Assessment Technique: New Evidence of Reliability

Science.gov (United States)

Kaufman, James C.; Lee, Joohyun; Baer, John; Lee, Soonmook

2007-01-01

The consensual assessment technique (CAT) is a measurement tool for creativity research in which appropriate experts evaluate creative products [Amabile, T. M. (1996). "Creativity in context: Update to the social psychology of creativity." Boulder, CO: Westview]. However, the CAT is hampered by the time-consuming nature of the products (asking…

Technology development on the assessment of structural integrity of nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Seo, Jeong Moon; Choun, Y. S.; Choi, I. K. and others

1999-04-01

Nuclear power plants in Korea show drop off in their performance and safety margin as the age of plants increase. The reevaluation of Kori-1 Unit on its performance and safety for life extension is expected in the near future. However, technologies and information related are insufficient to quantitatively estimate them. The final goal of this study is to develop the basic testing and evaluation techniques related with structural integrity of important nuclear equipment and structures. A part of the study includes development of equipment qualification technique. To ensure the structural integrity of structures, systems, and equipment in nuclear power plants, the following 5 research tasks were performed in the first year. - Analysis of dynamic characteristics of reactor internals - Analysis of engineering characteristics of instrumental earthquakes recorded in Korea - Analysis of ultimate pressure capacity and failure mode of containments building - Development of advanced NDE techniques using ultrasonic resonance scattering - Development of equipment qualification technique against vibration aging. These technologies developed in this study can be used to ensure the structural safety of operational nuclear power plants, and for the long-term life management. (author)

Electrical-Based Diagnostic Techniques for Assessing Insulation Condition in Aged Transformers

Directory of Open Access Journals (Sweden)

Issouf Fofana

2016-08-01

Full Text Available The condition of the internal cellulosic paper and oil insulation are of concern for the performance of power transformers. Over the years, a number of methods have been developed to diagnose and monitor the degradation/aging of the transformer internal insulation system. Some of this degradation/aging can be assessed from electrical responses. Currently there are a variety of electrical-based diagnostic techniques available for insulation condition monitoring of power transformers. In most cases, the electrical signals being monitored are due to mechanical or electric changes caused by physical changes in resistivity, inductance or capacitance, moisture, contamination or aging by-products in the insulation. This paper presents a description of commonly used and modern electrical-based diagnostic techniques along with their interpretation schemes.

Comparative study of electromechanical impedance and Lamb wave techniques for fatigue crack detection and monitoring in metallic structures

Science.gov (United States)

Lim, Say Ian; Liu, Yu; Soh, Chee Kiong

2012-04-01

Fatigue cracks often initiate at the weld toes of welded steel connections. Usually, these cracks cannot be identified by the naked eyes. Existing identification methods like dye-penetration test and alternating current potential drop (ACPD) may be useful for detecting fatigue cracks at the weld toes. To apply these non-destructive evaluation (NDE) techniques, the potential sites have to be accessible during inspection. Therefore, there is a need to explore other detection and monitoring techniques for fatigue cracks especially when their locations are inaccessible or cost of access is uneconomical. Electro-mechanical Impedance (EMI) and Lamb wave techniques are two fast growing techniques in the Structural Health Monitoring (SHM) community. These techniques use piezoelectric ceramics (PZT) for actuation and sensing. Since the monitoring site is only needed to be accessed once for the instrumentation of the transducers, remote monitoring is made possible. The permanent locations of these transducers also translate to having consistent measurement for monitoring. The main focus of this study is to conduct a comparative investigation on the effectiveness and efficiency of the EMI technique and the Lamb wave technique for successful fatigue crack identification and monitoring of welded steel connections using piezoelectric transducers. A laboratory-sized non-load carrying fillet weld specimen is used in this study. The specimen is subjected to cyclic tensile load and data for both techniques are acquired at stipulated intervals. It can be concluded that the EMI technique is sensitive to the crack initiation phase while the Lamb wave technique correlates well with the crack propagation phase.

Near-death experiences in non-life-threatening events and coma of different etiologies

Directory of Open Access Journals (Sweden)

Vanessa eCharland-Verville

2014-05-01

Full Text Available Background: Near death experiences (NDEs are increasingly being reported as a clearly identifiable physiological and psychological reality of clinical significance. However, the definition and causes of the phenomenon as well as the identification of NDE experiencers is still a matter of debate. To date, the most widely used standardized tool to identify and characterize NDEs in research is the Greyson NDE Scale. Using this scale, retrospective and prospective studies have been trying to estimate their incidence in various populations but few studies have tackled to associate the experiences’ intensity and content related to etiology. Methods: This retrospective investigation assessed the most frequently recounted features of self-reported NDEs after a non-life-threatening event (i.e., NDE-like experience or after a pathological coma (i.e., classical NDEs and according to the etiology of the acute brain insult. We also compared our retrospectively acquired data in anoxic coma with historical data from the published literature on prospective post-anoxic studies using the Greyson NDE Scale. Results: From our 190 reports who met the criteria for NDE (i.e., NDE scale total score Conclusions: It appears that real NDEs after coma of different etiologies are similar to NDE-like experiences occurring after non-life threatening events. Subjects reporting NDEs retrospectively tend to have experienced a different content compared to the prospective experiencers

ANDERS: future of concrete bridge deck evaluation and rehabilitation

Science.gov (United States)

Gucunski, Nenad; Moon, Franklin

2011-04-01

The Automated Nondestructive Evaluation and Rehabilitation System (ANDERS) aims to provide a uniquely comprehensive tool that will transform the manner in which bridge decks are assessed and rehabilitated. It is going to be achieved through: 1) much higher evaluation detail and comprehensiveness of detection at an early stage deterioration, 2) comprehensive condition and structural assessment at all stages of deterioration, and 3) integrated assessment and rehabilitation that will be minimally invasive, rapid and cost effective. ANDERS is composed of four systems. that merge novel imaging and NDE techniques, together with novel intervention approaches to arrest the deterioration processes. These technologies are incorporated within a series of human-operated and robotic vehicles. To perform assessments, ANDERS will be equipped with two complimentary nondestructive approaches. The first, Multi-Modal Nondestructive Evaluation (MM-NDE) System aims to identify and characterize localized deterioration with a high degree of resolution. The second, Global Structural Assessment (GSA) System aims to capture global structural characteristics and identify any appreciable effects of deterioration on a bridge structure. Output from these two approaches will be merged through a novel Automated Structural Identification (Auto St-Id) approach that will construct, calibrate, and utilize simulation models to assess overall structural vulnerability and capacity. These three systems comprise the assessment suite of ANDERS and will directly inform the Nondestructive Rehabilitation (NDR) System. The NDR System leverages robotics for the precision and rapid delivery of novel materials capable of halting the early-stage deterioration identified.

Road traffic air and noise pollution exposure assessment - A review of tools and techniques.

Science.gov (United States)

Khan, Jibran; Ketzel, Matthias; Kakosimos, Konstantinos; Sørensen, Mette; Jensen, Steen Solvang

2018-09-01

Road traffic induces air and noise pollution in urban environments having negative impacts on human health. Thus, estimating exposure to road traffic air and noise pollution (hereafter, air and noise pollution) is important in order to improve the understanding of human health outcomes in epidemiological studies. The aims of this review are (i) to summarize current practices of modelling and exposure assessment techniques for road traffic air and noise pollution (ii) to highlight the potential of existing tools and techniques for their combined exposure assessment for air and noise together with associated challenges, research gaps and priorities. The study reviews literature about air and noise pollution from urban road traffic, including other relevant characteristics such as the employed dispersion models, Geographic Information System (GIS)-based tool, spatial scale of exposure assessment, study location, sample size, type of traffic data and building geometry information. Deterministic modelling is the most frequently used assessment technique for both air and noise pollution of short-term and long-term exposure. We observed a larger variety among air pollution models as compared to the applied noise models. Correlations between air and noise pollution vary significantly (0.05-0.74) and are affected by several parameters such as traffic attributes, building attributes and meteorology etc. Buildings act as screens for the dispersion of pollution, but the reduction effect is much larger for noise than for air pollution. While, meteorology has a greater influence on air pollution levels as compared to noise, although also important for noise pollution. There is a significant potential for developing a standard tool to assess combined exposure of traffic related air and noise pollution to facilitate health related studies. GIS, due to its geographic nature, is well established and has a significant capability to simultaneously address both exposures. Copyright �

Assessment of multi-version NPP I and C systems safety. Metric-based approach, technique and tool

International Nuclear Information System (INIS)

Kharchenko, Vyacheslav; Volkovoy, Andrey; Bakhmach, Eugenii; Siora, Alexander; Duzhyi, Vyacheslav

2011-01-01

The challenges related to problem of assessment of actual diversity level and evaluation of diversity-oriented NPP I and C systems safety are analyzed. There are risks of inaccurate assessment and problems of insufficient decreasing probability of CCFs. CCF probability of safety-critical systems may be essentially decreased due to application of several different types of diversity (multi-diversity). Different diversity types of FPGA-based NPP I and C systems, general approach and stages of diversity and safety assessment as a whole are described. Objectives of the report are: (a) analysis of the challenges caused by use of diversity approach in NPP I and C systems in context of FPGA and other modern technologies application; (b) development of multi-version NPP I and C systems assessment technique and tool based on check-list and metric-oriented approach; (c) case-study of the technique: assessment of multi-version FPGA-based NPP I and C developed by use of Radiy TM Platform. (author)

Towards Intelligent Interpretation of Low Strain Pile Integrity Testing Results Using Machine Learning Techniques.

Science.gov (United States)

Cui, De-Mi; Yan, Weizhong; Wang, Xiao-Quan; Lu, Lie-Min

2017-10-25

Low strain pile integrity testing (LSPIT), due to its simplicity and low cost, is one of the most popular NDE methods used in pile foundation construction. While performing LSPIT in the field is generally quite simple and quick, determining the integrity of the test piles by analyzing and interpreting the test signals (reflectograms) is still a manual process performed by experienced experts only. For foundation construction sites where the number of piles to be tested is large, it may take days before the expert can complete interpreting all of the piles and delivering the integrity assessment report. Techniques that can automate test signal interpretation, thus shortening the LSPIT's turnaround time, are of great business value and are in great need. Motivated by this need, in this paper, we develop a computer-aided reflectogram interpretation (CARI) methodology that can interpret a large number of LSPIT signals quickly and consistently. The methodology, built on advanced signal processing and machine learning technologies, can be used to assist the experts in performing both qualitative and quantitative interpretation of LSPIT signals. Specifically, the methodology can ease experts' interpretation burden by screening all test piles quickly and identifying a small number of suspected piles for experts to perform manual, in-depth interpretation. We demonstrate the methodology's effectiveness using the LSPIT signals collected from a number of real-world pile construction sites. The proposed methodology can potentially enhance LSPIT and make it even more efficient and effective in quality control of deep foundation construction.

Nondestructive analysis of irradiated fuels

International Nuclear Information System (INIS)

Dudey, N.D.; Frick, D.C.

1977-01-01

The principal nondestructive examination techniques presently used to assess the physical integrity of reactor fuels and cladding materials include gamma-scanning, profilometry, eddy current, visual inspection, rod-to-rod spacing, and neutron radiography. LWR fuels are generally examined during annual refueling outages, and are conducted underwater in the spent fuel pool. FBR fuels are primarily examined in hot cells after fuel discharge. Although the NDE techniques are identical, LWR fuel examinations emphasize tests to demonstrate adherence to technical specification and reliable fuel performance; whereas, FBR fuel examinations emphasize aspects more related to the relative performance of different types of fuel and cladding materials subjected to variable irradiation conditions

Life Cycle Assessments of Manure Management Techniques for the Baltic Sea Regions

DEFF Research Database (Denmark)

Hamelin, Lorie; Baky, A; Cano-Bernal, J

The report summarizes the key results of the consequential life cycle assessments (LCAs) carried out for a variety of manure management techniques over the Baltic Sea Regions (BSR). For all manure management technologies assessed, the environmental impacts (in terms of potential to global warming......, acidification of aquatic & terrestrial systems as well as phosphorus and nitrogen enrichment) are evaluated along the whole “manure management chain”, quantified and compared to the applying reference manure management system. The LCA results presented in this report cover 4 main manure types (dairy cow slurry....... Assessed separation technologies include concentration technologies, state-of-the-art decanter centrifuge and source-separation technologies. The energy production technologies addressed consist of thermal gasification, incineration and anaerobic digestion (for which a myriad of carbon co...

Fatigue Life Assessment of Structures Using Electro-Mechanical Impedance Technique

International Nuclear Information System (INIS)

Bhalla, S

2012-01-01

This paper describes a new experimental approach for fatigue life assessment of structures based on the equivalent stiffness determined by surface bonded piezo-impedance transducers through the electro-mechanical impedance (EMI) technique. The remaining life of the component (in terms of the cycles of loading that can be sustained) is non-dimensionally correlated with the equivalent identified stiffness. The proposed approach circumvents the determination of the absolute stiffness of the joint and employs the admittance signature of the surface-bonded piezo-transducers directly. The second part of the paper briefly describes the recent advances made in the field of impedance based structural health monitoring (SHM) in terms of low-cost hardware system and improved damage diagnosis through the integration of global dynamic and EMI techniques using the same set of piezo-sensors. Other recent applications such as bio-sensors and traffic sensors pioneered at the Smart Structures and Dynamics Laboratory (SSDL) are also briefly covered.

Determining Remaining Useful Life of Aging Cables in Nuclear Power Plants – Interim Study FY13

Energy Technology Data Exchange (ETDEWEB)

Simmons, Kevin L.; Fifield, Leonard S.; Westman, Matthew P.; Ramuhalli, Pradeep; Pardini, Allan F.; Tedeschi, Jonathan R.; Jones, Anthony M.

2013-09-27

The most important criterion for cable performance is its ability to withstand a design-basis accident. With nearly 1000 km of power, control, instrumentation, and other cables typically found in an NPP, it would be a significant undertaking to inspect all of the cables. Degradation of the cable jacket, electrical insulation, and other cable components is a key issue that is likely to affect the ability of the currently installed cables to operate safely and reliably for another 20 to 40 years beyond the initial operating life. The development of one or more nondestructive evaluation (NDE) techniques and supporting models that could assist in determining the remaining life expectancy of cables or their current degradation state would be of significant interest. The ability to nondestructively determine material and electrical properties of cable jackets and insulation without disturbing the cables or connections has been deemed essential. Currently, the only technique accepted by industry to measure cable elasticity (the gold standard for determining cable insulation degradation) is the indentation measurement. All other NDE techniques are used to find flaws in the cable and do not provide information to determine the current health or life expectancy. There is no single NDE technique that can satisfy all of the requirements needed for making a life-expectancy determination, but a wide range of methods have been evaluated for use in NPPs as part of a continuous evaluation program. The commonly used methods are indentation and visual inspection, but these are only suitable for easily accessible cables. Several NDE methodologies using electrical techniques are in use today for flaw detection but there are none that can predict the life of a cable. There are, however, several physical and chemical ptoperty changes in cable insulation as a result of thermal and radiation damage. In principle, these properties may be targets for advanced NDE methods to provide early

Determining Remaining Useful Life of Aging Cables in Nuclear Power Plants - Interim Study FY13

International Nuclear Information System (INIS)

Simmons, Kevin L.; Fifield, Leonard S.; Westman, Matthew P.; Ramuhalli, Pradeep; Pardini, Allan F.; Tedeschi, Jonathan R.; Jones, Anthony M.

2013-01-01

The most important criterion for cable performance is its ability to withstand a design-basis accident. With nearly 1000 km of power, control, instrumentation, and other cables typically found in an NPP, it would be a significant undertaking to inspect all of the cables. Degradation of the cable jacket, electrical insulation, and other cable components is a key issue that is likely to affect the ability of the currently installed cables to operate safely and reliably for another 20 to 40 years beyond the initial operating life. The development of one or more nondestructive evaluation (NDE) techniques and supporting models that could assist in determining the remaining life expectancy of cables or their current degradation state would be of significant interest. The ability to nondestructively determine material and electrical properties of cable jackets and insulation without disturbing the cables or connections has been deemed essential. Currently, the only technique accepted by industry to measure cable elasticity (the gold standard for determining cable insulation degradation) is the indentation measurement. All other NDE techniques are used to find flaws in the cable and do not provide information to determine the current health or life expectancy. There is no single NDE technique that can satisfy all of the requirements needed for making a life-expectancy determination, but a wide range of methods have been evaluated for use in NPPs as part of a continuous evaluation program. The commonly used methods are indentation and visual inspection, but these are only suitable for easily accessible cables. Several NDE methodologies using electrical techniques are in use today for flaw detection but there are none that can predict the life of a cable. There are, however, several physical and chemical ptoperty changes in cable insulation as a result of thermal and radiation damage. In principle, these properties may be targets for advanced NDE methods to provide early

Assessment techniques for a learning-centered curriculum: evaluation design for adventures in supercomputing

Energy Technology Data Exchange (ETDEWEB)

Helland, B. [Ames Lab., IA (United States); Summers, B.G. [Oak Ridge National Lab., TN (United States)

1996-09-01

As the classroom paradigm shifts from being teacher-centered to being learner-centered, student assessments are evolving from typical paper and pencil testing to other methods of evaluation. Students should be probed for understanding, reasoning, and critical thinking abilities rather than their ability to return memorized facts. The assessment of the Department of Energy`s pilot program, Adventures in Supercomputing (AiS), offers one example of assessment techniques developed for learner-centered curricula. This assessment has employed a variety of methods to collect student data. Methods of assessment used were traditional testing, performance testing, interviews, short questionnaires via email, and student presentations of projects. The data obtained from these sources have been analyzed by a professional assessment team at the Center for Children and Technology. The results have been used to improve the AiS curriculum and establish the quality of the overall AiS program. This paper will discuss the various methods of assessment used and the results.

Time-Domain Terahertz Computed Axial Tomography NDE System

Science.gov (United States)

Zimdars, David

2012-01-01

NASA has identified the need for advanced non-destructive evaluation (NDE) methods to characterize aging and durability in aircraft materials to improve the safety of the nation's airline fleet. 3D THz tomography can play a major role in detection and characterization of flaws and degradation in aircraft materials, including Kevlar-based composites and Kevlar and Zylon fabric covers for soft-shell fan containment where aging and durability issues are critical. A prototype computed tomography (CT) time-domain (TD) THz imaging system has been used to generate 3D images of several test objects including a TUFI tile (a thermal protection system tile used on the Space Shuttle and possibly the Orion or similar capsules). This TUFI tile had simulated impact damage that was located and the depth of damage determined. The CT motion control gan try was designed and constructed, and then integrated with a T-Ray 4000 control unit and motion controller to create a complete CT TD-THz imaging system prototype. A data collection software script was developed that takes multiple z-axis slices in sequence and saves the data for batch processing. The data collection software was integrated with the ability to batch process the slice data with the CT TD-THz image reconstruction software. The time required to take a single CT slice was decreased from six minutes to approximately one minute by replacing the 320 ps, 100-Hz waveform acquisition system with an 80 ps, 1,000-Hz waveform acquisition system. The TD-THZ computed tomography system was built from pre-existing commercial off-the-shelf subsystems. A CT motion control gantry was constructed from COTS components that can handle larger samples. The motion control gantry allows inspection of sample sizes of up to approximately one cubic foot (.0.03 cubic meters). The system reduced to practice a CT-TDTHz system incorporating a COTS 80- ps/l-kHz waveform scanner. The incorporation of this scanner in the system allows acquisition of 3D

Low Frequency Phased Array Application for Crack Detection in Cast Austenitic Piping

International Nuclear Information System (INIS)

Anderson, Michael T.; Cumblidge, Stephen E.; Doctor, Steven R.

2006-01-01

As part of a multi-year program funded by the United States Nuclear Regulatory Commission (US NRC) to address nondestructive examination (NDE) reliability of inservice inspection (ISI) programs, studies conducted at the Pacific Northwest National Laboratory (PNNL) in Richland, Washington, have focused on assessing novel NDE approaches for the inspection of coarse-grained, cast stainless steel reactor components. The primary objective of this work is to provide information to the US NRC on the utility, effectiveness and reliability of ultrasonic testing (UT) as related to the ISI of primary piping components in US commercial nuclear power plants. This paper describes progress, recent developments and results from an assessment of a portion of the work relating to the ultrasonic low frequency phased array inspection technique. Westinghouse Owner's Group (WOG) cast stainless steel pipe segments with thermal and mechanical fatigue cracks, PNNL samples containing thermal fatigue cracks and several blank vintage specimens having very coarse grains that are representative of early centrifugally cast piping installed in PWRs, were used for assessing the inspection method. The phased array approach was implemented using an R/D Tech Tomoscan III system operating at 1.0 MHz and 500 kHz, providing composite volumetric images of the samples. Several dual, transmit-receive, custom designed low-frequency arrays were employed in laboratory trials. Results from laboratory studies for assessing detection, localization and length sizing effectiveness are discussed.

Assessing Morphological and Physiological Properties of Forest Species Using High Throughput Plant Phenotyping and Imaging Techniques

Science.gov (United States)

Mazis, A.; Hiller, J.; Morgan, P.; Awada, T.; Stoerger, V.

2017-12-01

High throughput plant phenotyping is increasingly being used to assess morphological and biophysical traits of economically important crops in agriculture. In this study, the potential application of this technique in natural resources management, through the characterization of woody plants regeneration, establishment, growth, and responses to water and nutrient manipulations was assessed. Two woody species were selected for this study, Quercus prinoides and Quercus bicolor. Seeds were collected from trees growing at the edge of their natural distribution in Nebraska and Missouri, USA. Seeds were germinated in the greenhouse and transferred to the Nebraska Innovation Campus Lemnatec3D High Throughput facility at the University of Nebraska-Lincoln. Seedlings subjected to water and N manipulations, were imaged twice or three times a week using four cameras (Visible, Fluorescence, Infrared and Hyperspectral), throughout the growing season. Traditional leaf to plant levels ecophysiological measurements were concurrently acquired to assess the relationship between these two techniques. These include gas exchange (LI 6400 and LI 6800, LICOR Inc., Lincoln NE), chlorophyll content, optical characteristics (Ocean Optics USB200), water and osmotic potentials, leaf area and weight and carbon isotope ratio. In the presentation, we highlight results on the potential use of high throughput plant phenotyping techniques to assess the morphology and physiology of woody species including responses to water availability and nutrient manipulation, and its broader application under field conditions and natural resources management. Also, we explore the different capabilities imaging provides us for modeling the plant physiological and morphological growth and how it can complement the current techniques

Innovative technique for assessment of groundwater quality

International Nuclear Information System (INIS)

Ahmad, N.; Ahmad, M.; Sajjad, M.I.

2001-07-01

Groundwater quality of a part of Chaj Doab has been assessed with innovative techniques which are not reported in literature. The concept of triangular coordinates is modified by multi-rectangular ones for the classification of major cations and anions analysed in the ground water. A Multi-Rectangular Diagram (MRD) has been developed with the combination of rectangular coordinates by virtue of which milli-equivalent per liter percentages (meq/1%) of major cations and anions could be classified into different categories more efficiently as compared to classical trilinear diagrams. Both Piper diagram and MRD are used for the assessment of 259 data sets analysed from ground water of Chaj Doab area, Pakistan. The differentiated ground water types with MRD in the study area are calcium bicarbonate, magnesium bicarbonate, sodium bicarbonate and sodium sulfate. Sodium bicarbonate type emerges as the most abundant type of ground water in the study area. A map showing spatial variation of groundwater quality has been constructed with the help of MRD. This map shows that, in the vicinity of rivers Chenab and Jhelum, calcium bicarbonate type of waters occur while the central area is mainly covered by sodium bicarbonate dominant waters. Groundwaters near the upper Jhelum canal are dominant in sodium sulfate. An important relation between calcium and sodium is proposed which explains the movement history of groundwater in the aquifer. Hydrogeochemical processes have been evaluated with new methods. Ion exchange between calcium and sodium, precipitation of calcium bicarbonate and dissolution of rock forming minerals are the major delineated hydrogeochemical processes. (author)

Arthroscopic Latarjet Techniques: Graft and Fixation Positioning Assessed With 2-Dimensional Computed Tomography Is Not Equivalent With Standard Open Technique.

Science.gov (United States)

Neyton, Lionel; Barth, Johannes; Nourissat, Geoffroy; Métais, Pierre; Boileau, Pascal; Walch, Gilles; Lafosse, Laurent

2018-05-19

To analyze graft and fixation (screw and EndoButton) positioning after the arthroscopic Latarjet technique with 2-dimensional computed tomography (CT) and to compare it with the open technique. We performed a retrospective multicenter study (March 2013 to June 2014). The inclusion criteria included patients with recurrent anterior instability treated with the Latarjet procedure. The exclusion criterion was the absence of a postoperative CT scan. The positions of the hardware, the positions of the grafts in the axial and sagittal planes, and the dispersion of values (variability) were compared. The study included 208 patients (79 treated with open technique, 87 treated with arthroscopic Latarjet technique with screw fixation [arthro-screw], and 42 treated with arthroscopic Latarjet technique with EndoButton fixation [arthro-EndoButton]). The angulation of the screws was different in the open group versus the arthro-screw group (superior, 10.3° ± 0.7° vs 16.9° ± 1.0° [P open inferior screws (P = .003). In the axial plane (level of equator), the arthroscopic techniques resulted in lateral positions (arthro-screw, 1.5 ± 0.3 mm lateral [P open technique (0.9 ± 0.2 mm medial). At the level of 25% of the glenoid height, the arthroscopic techniques resulted in lateral positions (arthro-screw, 0.3 ± 0.3 mm lateral [P open technique (1.0 ± 0.2 mm medial). Higher variability was observed in the arthro-screw group. In the sagittal plane, the arthro-screw technique resulted in higher positions (55% ± 3% of graft below equator) and the arthro-EndoButton technique resulted in lower positions (82% ± 3%, P open technique (71% ± 2%). Variability was not different. This study shows that the position of the fixation devices and position of the bone graft with the arthroscopic techniques are statistically significantly different from those with the open technique with 2-dimensional CT assessment. In the sagittal plane, the arthro-screw technique provides the highest

In-Space Inspection Technologies Vision

Science.gov (United States)

Studor, George

2012-01-01

Purpose: Assess In-Space NDE technologies and needs - current & future spacecraft. Discover & build on needs, R&D & NDE products in other industries and agencies. Stimulate partnerships in & outside NASA to move technologies forward cooperatively. Facilitate group discussion on challenges and opportunities of mutual benefit. Focus Areas: Miniaturized 3D Penetrating Imagers Controllable Snake-arm Inspection systems Miniature Free-flying Micro-satellite Inspectors

Standard Guide for Acousto-Ultrasonic Assessment of Composites, Laminates, and Bonded Joints

CERN Document Server

American Society for Testing and Materials. Philadelphia

2007-01-01

1.1 This guide explains the rationale and basic technology for the acousto-ultrasonic (AU) method. Guidelines are given for nondestructive evaluation (NDE) of flaws and physical characteristics that influence the mechanical properties and relative strength of composite structures (for example, filament-wound pressure vessels), adhesive bonds (for example, joints between metal plates), and interlaminar and fiber/matrix bonds in man-made composites and natural composites (for example, wood products). 1.2 This guide covers technical details and rules that must be observed to ensure reliable and reproducible quantitative AU assessments of laminates, composites, and bonded structures. The underlying principles, prototype apparatus, instrumentation, standardization, examination methods, and data analysis for such assessments are covered. Limitations of the AU method and guidelines for taking advantage of its capabilities are cited. 1.3 The objective of AU is to assess subtle flaws and associated strength variations...

Progress in evaluation and improvement in nondestructive examination reliability for inservice inspection of Light Water Reactors (LWRs) and characterize fabrication flaws in reactor pressure vessels

International Nuclear Information System (INIS)

Doctor, S.R.; Bowey, R.E.; Good, M.S.; Friley, J.R.; Kurtz, R.J.; Simonen, F.A.; Taylor, T.T.; Heasler, P.G.; Andersen, E.S.; Diaz, A.A.; Greenwood, M.S.; Hockey, R.L.; Schuster, G.J.; Spanner, J.C.; Vo, T.V.

1991-10-01

This paper is a review of the work conducted under two programs. One (NDE Reliability Program) is a multi-year program addressing the reliability of nondestructive evaluation (NDE) for the inservice inspection (ISI) of light water reactor components. This program examines the reliability of current NDE, the effectiveness of evolving technologies, and provides assessments and recommendations to ensure that the NDE is applied at the right time, in the right place with sufficient effectiveness that defects of importance to structural integrity will be reliably detected and accurately characterized. The second program (Characterizing Fabrication Flaws in Reactor Pressure Vessels) is assembling a data base to quantify the distribution of fabrication flaws that exist in US nuclear reactor pressure vessels with respect to density, size, type, and location. These programs will be discussed as two separate sections in this report. 4 refs., 7 figs

The effect of manufacturing conditions on discontinuity population and fatigue fracture behavior in carbon/epoxy composites

Science.gov (United States)

Hakim, Issa; Laquai, Rene; Walter, David; Mueller, Bernd; Graja, Paul; Meyendorf, Norbert; Donaldson, Steven

2017-02-01

Carbon fiber composites have been increasingly used in aerospace, military, sports, automotive and other fields due to their excellent properties, including high specific strength, high specific modulus, corrosion resistance, fatigue resistance, and low thermal expansion coefficient. Interlaminar fracture is a serious failure mode leading to a loss in composite stiffness and strength. Discontinuities formed during manufacturing process degrade the fatigue life and interlaminar fracture resistance of the composite. In his study, three approaches were implemented and their results were correlated to quantify discontinuities effecting static and fatigue interlaminar fracture behavior of carbon fiber composites. Samples were fabricated by hand layup vacuum bagging manufacturing process under three different vacuum levels, indicated High (-686 mmHg), Moderate (-330 mmHg) and Poor (0 mmHg). Discontinuity content was quantified through-thickness by destructive and nondestructive techniques. Eight different NDE methods were conducted including imaging NDE methods: X-Ray laminography, ultrasonic, high frequency eddy current, pulse thermography, pulse phase thermography and lock-in-thermography, and averaging NDE techniques: X-Ray refraction and thermal conductivity measurements. Samples were subsequently destructively serial sectioned through-thickness into several layers. Both static and fatigue interlaminar fracture behavior under Mode I were conducted. The results of several imaging NDE methods revealed the trend in percentages of discontinuity. However, the results of averaging NDE methods showed a clear correlation since they gave specific values of discontinuity through-thickness. Serial sectioning exposed the composite's internal structure and provided a very clear idea about the type, shape, size, distribution and location of most discontinuities included. The results of mechanical testing showed that discontinuities lead to a decrease in Mode I static interlaminar

Teaching and Assessment of High-Velocity, Low-Amplitude Techniques for the Spine in Predoctoral Medical Education.

Science.gov (United States)

Channell, Millicent King

2016-09-01

Although national didactic criteria have been set for predoctoral education and assessment in osteopathic manipulative treatment, there is no criterion standard for teaching methods and assessments of osteopathic manipulative treatment competence in colleges of osteopathic medicine. This issue is more pressing with the creation of the single graduate medical education accreditation system by the American Osteopathic Association and Accreditation Council for Graduate Medical Education, which introduced the creation of "osteopathic recognition" for residencies that want to incorporate osteopathic principles and practice into their programs. Residencies with osteopathic recognition may include both osteopathic and allopathic graduates. Increased standardization at the predoctoral level, however, is recommended as osteopathic principles and practice training applications are expanded. The objectives of this article are to review the standards for teaching osteopathic medical students high-velocity, low-amplitude (HVLA) techniques for the spine; to review and discuss the methods used to assess medical students' proficiency in using HVLA; and to propose baseline standards for teaching and assessing HVLA techniques among medical students.

Nondestructive examinations performance demonstration standpoint of the BCCN (Nuclear Construction Inspection Office)

International Nuclear Information System (INIS)

Deschamps, J.; Novat, J.

1994-01-01

The part played by in service non-destructive examinations (NDE) in the safety assessment of French nuclear power plants has developed considerably since startup of the first PWR unit 15 years ago. In 15 years of operation and continued plant construction, defects came to light, revealed either by a non-destructive examination or a leak occurring in operation or during hydrostatic test. It is consequently necessary to operate reactors affected by defects already detected or liable to develop according to a known mechanism. This practice is only acceptable if it can be proved that the defects will remain harmless in all situations. This implies that they can be detected without fail beyond a certain threshold, that they can be characterized and that their propensity to develop can be measured. In some cases, only NDE data can justify the continued operation of a reactor. Maximum guarantees as to the performances and reliability of these examinations are consequently indispensable, since plant safety conclusions will be based on their results. This paper discusses: the advantages of an NDE performance demonstration program; practical assessments role; and NDE performance demonstration stages

Review of progress in quantitative nondestructive evaluation

CERN Document Server

Chimenti, Dale

1999-01-01

This series provides a comprehensive review of the latest research results in quantitative nondestructive evaluation (NDE). Leading investigators working in government agencies, major industries, and universities present a broad spectrum of work extending from basic research to early engineering applications. An international assembly of noted authorities in NDE thoroughly cover such topics as: elastic waves, guided waves, and eddy-current detection, inversion, and modeling; radiography and computed tomography, thermal techniques, and acoustic emission; laser ultrasonics, optical methods, and microwaves; signal processing and image analysis and reconstruction, with an emphasis on interpretation for defect detection; and NDE sensors and fields, both ultrasonic and electromagnetic; engineered materials and composites, bonded joints, pipes, tubing, and biomedical materials; linear and nonlinear properties, ultrasonic backscatter and microstructure, coatings and layers, residual stress and texture, and constructi...

A cross-sectional observational study to assess inhaler technique in Saudi hospitalized patients with asthma and chronic obstructive pulmonary disease

Science.gov (United States)

Ammari, Maha Al; Sultana, Khizra; Yunus, Faisal; Ghobain, Mohammed Al; Halwan, Shatha M. Al

2016-01-01

Objectives: To assess the proportion of critical errors committed while demonstrating the inhaler technique in hospitalized patients diagnosed with asthma and chronic obstructive pulmonary disease (COPD). Methods: This cross-sectional observational study was conducted in 47 asthmatic and COPD patients using inhaler devices. The study took place at King Abdulaziz Medical City, Riyadh, Saudi Arabia between September and December 2013. Two pharmacists independently assessed inhaler technique with a validated checklist. Results: Seventy percent of patients made at least one critical error while demonstrating their inhaler technique, and the mean number of critical errors per patient was 1.6. Most patients used metered dose inhaler (MDI), and 73% of MDI users and 92% of dry powder inhaler users committed at least one critical error. Conclusion: Inhaler technique in hospitalized Saudi patients was inadequate. Health care professionals should understand the importance of reassessing and educating patients on a regular basis for inhaler technique, recommend the use of a spacer when needed, and regularly assess and update their own inhaler technique skills. PMID:27146622

A Bio-Inspired Herbal Tea Flavour Assessment Technique

Directory of Open Access Journals (Sweden)

Nur Zawatil Isqi Zakaria

2014-07-01

Full Text Available Herbal-based products are becoming a widespread production trend among manufacturers for the domestic and international markets. As the production increases to meet the market demand, it is very crucial for the manufacturer to ensure that their products have met specific criteria and fulfil the intended quality determined by the quality controller. One famous herbal-based product is herbal tea. This paper investigates bio-inspired flavour assessments in a data fusion framework involving an e-nose and e-tongue. The objectives are to attain good classification of different types and brands of herbal tea, classification of different flavour masking effects and finally classification of different concentrations of herbal tea. Two data fusion levels were employed in this research, low level data fusion and intermediate level data fusion. Four classification approaches; LDA, SVM, KNN and PNN were examined in search of the best classifier to achieve the research objectives. In order to evaluate the classifiers’ performance, an error estimator based on k-fold cross validation and leave-one-out were applied. Classification based on GC-MS TIC data was also included as a comparison to the classification performance using fusion approaches. Generally, KNN outperformed the other classification techniques for the three flavour assessments in the low level data fusion and intermediate level data fusion. However, the classification results based on GC-MS TIC data are varied.

Assessment of tumors of the lung apex by imaging techniques

International Nuclear Information System (INIS)

Rueda, J.; Serrano, F.; Pain, M.I.; Rodriguez, F.

1996-01-01

The purpose of this study was to analyze the value of MR in the preoperative staging of tumors of the lung apex and detection of local invasion of adjacent structures to determine its influence on the therapeutic approach. We obtained plain X-ray images in two planes, as well as CT and Mr images, in 12 patients with Pan coast tumor in whom there was surgical (n=8) or clinical (n=4) evidence of invasion. The objective was to assess local infiltration of brain stem and chest wall soft tissue, enveloping of the subclavian artery, substantial involvement of the brachial plexus and destruction of the vertebral body. In our series, MR was superior to the other imaging techniques in predicting the involvement of the structures surrounding the tumor. In conclusion, MR should be performed in a patient diagnosed by plain radiography as having an apical tumors to assess local tumor extension, while CT should be done to detect mediastinal lymph node involvement and distant metastases. 19 refs

Biomechanical Effect of Margin Convergence Techniques: Quantitative Assessment of Supraspinatus Muscle Stiffness.

Directory of Open Access Journals (Sweden)

Taku Hatta

Full Text Available Although the margin convergence (MC technique has been recognized as an option for rotator cuff repair, little is known about the biomechanical effect on repaired rotator cuff muscle, especially after supplemented footprint repair. The purpose of this study was to assess the passive stiffness changes of the supraspinatus (SSP muscle after MC techniques using shear wave elastography (SWE. A 30 × 40-mm U-shaped rotator cuff tear was created in 8 cadaveric shoulders. Each specimen was repaired with 6 types of MC technique (1-, 2-, 3-suture MC with/without footprint repair, in a random order at 30° glenohumeral abduction. Passive stiffness of four anatomical regions in the SSP muscle was measured based on an established SWE method. Data were obtained from the SSP muscle at 0° abduction under 8 different conditions: intact (before making a tear, torn, and postoperative conditions with 6 techniques. MC techniques using 1-, or 2-suture combined with footprint repair showed significantly higher stiffness values than the intact condition. Passive stiffness of the SSP muscle was highest after a 1-suture MC with footprint repair for all regions when compared among all repair procedures. There was no significant difference between the intact condition and a 3-suture MC with footprint repair. MC techniques with single stitch and subsequent footprint repair may have adverse effects on muscle properties and tensile loading on repair, increasing the risk of retear of repairs. Adding more MC stitches could reverse these adverse effects.

Assessment of ground-based monitoring techniques applied to landslide investigations

Science.gov (United States)

Uhlemann, S.; Smith, A.; Chambers, J.; Dixon, N.; Dijkstra, T.; Haslam, E.; Meldrum, P.; Merritt, A.; Gunn, D.; Mackay, J.

2016-01-01

A landslide complex in the Whitby Mudstone Formation at Hollin Hill, North Yorkshire, UK is periodically re-activated in response to rainfall-induced pore-water pressure fluctuations. This paper compares long-term measurements (i.e., 2009-2014) obtained from a combination of monitoring techniques that have been employed together for the first time on an active landslide. The results highlight the relative performance of the different techniques, and can provide guidance for researchers and practitioners for selecting and installing appropriate monitoring techniques to assess unstable slopes. Particular attention is given to the spatial and temporal resolutions offered by the different approaches that include: Real Time Kinematic-GPS (RTK-GPS) monitoring of a ground surface marker array, conventional inclinometers, Shape Acceleration Arrays (SAA), tilt meters, active waveguides with Acoustic Emission (AE) monitoring, and piezometers. High spatial resolution information has allowed locating areas of stability and instability across a large slope. This has enabled identification of areas where further monitoring efforts should be focused. High temporal resolution information allowed the capture of 'S'-shaped slope displacement-time behaviour (i.e. phases of slope acceleration, deceleration and stability) in response to elevations in pore-water pressures. This study shows that a well-balanced suite of monitoring techniques that provides high temporal and spatial resolutions on both measurement and slope scale is necessary to fully understand failure and movement mechanisms of slopes. In the case of the Hollin Hill landslide it enabled detailed interpretation of the geomorphological processes governing landslide activity. It highlights the benefit of regularly surveying a network of GPS markers to determine areas for installation of movement monitoring techniques that offer higher resolution both temporally and spatially. The small sensitivity of tilt meter measurements

Comparison of Risk Assessment Using HAZOP and ETBA Techniques: Case Study of a Gasoline Refinery Unit in Iran

Directory of Open Access Journals (Sweden)

Shirazeh Arghami

2015-12-01

Full Text Available Background: Prevention of accidents—a crucial requirement in oil industries—involves hazard recognition, risk assessment, and corrective actions. The purpose of this study was to compare the ETBA and HAZOP techniques for risk assessment in a gasoline refinery unit. Methods: In this case study, data were collected using process flow diagram, walking–talking through method, piping and instrumentation diagram, and direct observations. Worksheets for both techniques were filled on the basis of the risk assessment matrix MIL-STD-882E. Results: The HAZOP method identified 44 deviations attributable to 118 causes. In addition, 11.37% of the identified hazards were associated with unacceptable risk, and 36.36%, with unfavorable risk. The ETBA method detected 10 groups of energy (24 subgroups; 33 hazards were detected, 10.62% of which were associated with unacceptable risk. Conclusion: HAZOP proved to be the more powerful technique for the prediction and identification of hazards. However, ETBA detected certain hazards that were not identifiable using HAZOP. Therefore, a combination of these two methods is desirable for the assessment of hazard risk in process industries.

Plant-Damage Assessment Technique for Evaluating Military Vehicular Impacts to Vegetation in the Mojave Desert; TOPICAL

International Nuclear Information System (INIS)

D. J. Hansen; W. K. Ostler

2001-01-01

A new plant damage assessment technique was developed by plant ecologists from Bechtel Nevada at the U.S. Department of Energy's National Security Administration Nevada Operations Office and funded by the Strategic Environmental Research and Development Program Project CS-1131 in cooperation with the U.S. Army's National Training Center (NTC) at Fort Irwin, California. The technique establishes linear transects the width of vehicle tracts from evidence of vehicle tracks in the soil (usually during a prior training rotation period of 30 days or since the last rain or wind storm), and measures vegetation within the tracks to determine the area of plant parts being run over, the percent of the impacted parts damaged, and the percent of impacted parts expected to recover. It documents prior-damage classes based on estimated of damage that plants have apparently experienced previously (as assessed from field indicators of damage such as plant shape and height). The technique was used to evaluate different vehicle types (rubber-tire wheels vs. tracks) in six area at the NTC with different soils and training intensity levels. The technique provides tabular data that can be sorted and queried to show a variety of trends related to military vehicular impacts. The technique also appears suitable for assessing other non-military off-road traffic impacts. Findings report: (1) differences in plant sensitivity of different vehicular impacts, (2) plant cover and density by species and training area, (3) the degree to which wheels have less impact than tracks, and (4) the mean percent survival is inversely proportional to the degree of prior damage received by the vegetation (i.e., plants previously impacted have lower survival than plants not previously impacted)

Fatigue life estimation of a 1D aluminum beam under mode-I loading using the electromechanical impedance technique

International Nuclear Information System (INIS)

Lim, Yee Yan; Soh, Chee Kiong

2011-01-01

Structures in service are often subjected to fatigue loads. Cracks would develop and lead to failure if left unnoticed after a large number of cyclic loadings. Monitoring the process of fatigue crack propagation as well as estimating the remaining useful life of a structure is thus essential to prevent catastrophe while minimizing earlier-than-required replacement. The advent of smart materials such as piezo-impedance transducers (lead zirconate titanate, PZT) has ushered in a new era of structural health monitoring (SHM) based on non-destructive evaluation (NDE). This paper presents a series of investigative studies to evaluate the feasibility of fatigue crack monitoring and estimation of remaining useful life using the electromechanical impedance (EMI) technique employing a PZT transducer. Experimental tests were conducted to study the ability of the EMI technique in monitoring fatigue crack in 1D lab-sized aluminum beams. The experimental results prove that the EMI technique is very sensitive to fatigue crack propagation. A proof-of-concept semi-analytical damage model for fatigue life estimation has been developed by incorporating the linear elastic fracture mechanics (LEFM) theory into the finite element (FE) model. The prediction of the model matches closely with the experiment, suggesting the possibility of replacing costly experiments in future

Fatigue life estimation of a 1D aluminum beam under mode-I loading using the electromechanical impedance technique

Science.gov (United States)

Lim, Yee Yan; Kiong Soh, Chee

2011-12-01

Structures in service are often subjected to fatigue loads. Cracks would develop and lead to failure if left unnoticed after a large number of cyclic loadings. Monitoring the process of fatigue crack propagation as well as estimating the remaining useful life of a structure is thus essential to prevent catastrophe while minimizing earlier-than-required replacement. The advent of smart materials such as piezo-impedance transducers (lead zirconate titanate, PZT) has ushered in a new era of structural health monitoring (SHM) based on non-destructive evaluation (NDE). This paper presents a series of investigative studies to evaluate the feasibility of fatigue crack monitoring and estimation of remaining useful life using the electromechanical impedance (EMI) technique employing a PZT transducer. Experimental tests were conducted to study the ability of the EMI technique in monitoring fatigue crack in 1D lab-sized aluminum beams. The experimental results prove that the EMI technique is very sensitive to fatigue crack propagation. A proof-of-concept semi-analytical damage model for fatigue life estimation has been developed by incorporating the linear elastic fracture mechanics (LEFM) theory into the finite element (FE) model. The prediction of the model matches closely with the experiment, suggesting the possibility of replacing costly experiments in future.

Thick Concrete Specimen Construction, Testing, and Preliminary Analysis

Energy Technology Data Exchange (ETDEWEB)

Clayton, Dwight A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hoegh, Kyle [Univ. of Minnesota, Minneapolis, MN (United States); Khazanovich, Lev [Univ. of Minnesota, Minneapolis, MN (United States)

2015-03-01

The purpose of the U.S. Department of Energy Office of Nuclear Energy’s Light Water Reactor Sustainability (LWRS) Program is to develop technologies and other solutions that can improve the reliability, sustain the safety, and extend the operating lifetimes of nuclear power plants (NPPs) beyond 60 years. Since many important safety structures in an NPP are constructed of concrete, inspection techniques must be developed and tested to evaluate the internal condition. In-service containment structures generally do not allow for the destructive measures necessary to validate the accuracy of these inspection techniques. This creates a need for comparative testing of the various nondestructive evaluation (NDE) measurement techniques on concrete specimens with known material properties, voids, internal microstructure flaws, and reinforcement locations. A preliminary report detailed some of the challenges associated with thick reinforced concrete sections and prioritized conceptual designs of specimens that could be fabricated to represent NPP concrete structures for using in NDE evaluation comparisons. This led to the construction of the concrete specimen presented in this report, which has sufficient reinforcement density and cross-sectional size to represent an NPP containment wall. Details on how a suitably thick concrete specimen was constructed are presented, including the construction materials, final nominal design schematic, as well as formwork and rigging required to safely meet the desired dimensions of the concrete structure. The report also details the type and methods of forming the concrete specimen as well as information on how the rebar and simulated defects were embedded. Details on how the resulting specimen was transported, safely anchored, and marked to allow access for systematic comparative NDE testing of defects in a representative NPP containment wall concrete specimen are also given. Data collection using the MIRA Ultrasonic NDE equipment and

Non invasive blood flow assessment in diabetic foot ulcer using laser speckle contrast imaging technique

Science.gov (United States)

Jayanthy, A. K.; Sujatha, N.; Reddy, M. Ramasubba; Narayanamoorthy, V. B.

2014-03-01

Measuring microcirculatory tissue blood perfusion is of interest for both clinicians and researchers in a wide range of applications and can provide essential information of the progress of treatment of certain diseases which causes either an increased or decreased blood flow. Diabetic ulcer associated with alterations in tissue blood flow is the most common cause of non-traumatic lower extremity amputations. A technique which can detect the onset of ulcer and provide essential information on the progress of the treatment of ulcer would be of great help to the clinicians. A noninvasive, noncontact and whole field laser speckle contrast imaging (LSCI) technique has been described in this paper which is used to assess the changes in blood flow in diabetic ulcer affected areas of the foot. The blood flow assessment at the wound site can provide critical information on the efficiency and progress of the treatment given to the diabetic ulcer subjects. The technique may also potentially fulfill a significant need in diabetic foot ulcer screening and management.

Comparison of radiocarbon techniques for the assessment of biobase content in fuels

International Nuclear Information System (INIS)

Culp, Randy; Cherkinsky, Alex; Ravi Prasad, G.V.

2014-01-01

A comparison was made between various radiocarbon measurement techniques for the purpose of quantifying each methods capability for the proper apportionment of biobase-derived additives to gasoline. Measurement techniques include (1) direct liquid scintillation counting, (2) carbon dioxide absorption followed by liquid scintillation counting, (3) conversion to benzene followed by liquid scintillation counting and (4) accelerator mass spectrometry. In addition, stable isotope ratios of carbon and hydrogen were determined to assist in the authentication of a fuels source with regard to petrochemical or biobase origin is required for the confirmation of minimum anti-knock components, consumer awareness and proper assessment for regulatory taxation. Accelerator mass spectrometry was found to be the most precise technique followed by conversion of fuel to benzene with liquid scintillation counting and direct counting by liquid scintillation counting. Finally, liquid scintillation counting of absorbed carbon dioxide was found to be the least precise and should not be used for this analysis. The high to low precisions correlate with the high to low cost of equipment and support required by each of these methods except for direct liquid scintillation counting. Therefore, laboratories interested in developing capability to perform such authentication can use this data to consider the economics of the optimum technique to use for radiocarbon measurement

Lichen techniques of pollution assessment

Energy Technology Data Exchange (ETDEWEB)

O' Hare, G

1973-01-01

Available techniques for determining air pollution by sulfur dioxide using lichens are described. An application of these methods - species distributions, zone mapping and analyses of total sulfur content - in the west central Scotland area, is briefly reported.

Nonlinear analysis techniques for use in the assessment of high-level waste tank structures

International Nuclear Information System (INIS)

Moore, C.J.; Julyk, L.J.; Fox, G.L.; Dyrness, A.D.

1991-01-01

Reinforced concrete in combination with a steel liner has had a wide application to structures containing hazardous material. The buried double-shell waste storage tanks at the US Department of Energy's Hanford Site use this construction method. The generation and potential ignition of combustible gases within the primary tank is postulated to develop beyond-design-basis internal pressure and possible impact loading. The scope of this paper includes the illustration of analysis techniques for the assessment of these beyond-design-basis loadings. The analysis techniques include the coupling of the gas dynamics with the structural response, the treatment of reinforced concrete in regimes of inelastic behavior, and the treatment of geometric nonlinearities. The techniques and software tools presented provide a powerful nonlinear analysis capability for storage tanks

Histologic assessment of biliary obstruction with different percutaneous endoluminal techniques

Directory of Open Access Journals (Sweden)

Guido Giampiero

2004-08-01

Full Text Available Abstract Background Despite the sophisticated cross sectional image techniques currently available, a number of biliary stenosis or obstructions remain of an uncertain nature. In these pathological conditions, an "intrinsic" parietal alteration is the cause of biliary obstruction and it is very difficult to differentiate benign from malignant lesions using cross-sectional imaging procedures alone. We evaluated the efficacy of different endoluminal techniques to achieve a definitive pathological diagnosis in these situations. Methods Eighty patients underwent brushing, and or biopsy of the biliary tree through an existing transhepatic biliary drainage route. A subcoort of 12 patients needed balloon-dilatation of the bile duct and the material covering the balloon surface was also sent for pathological examination (balloon surface sampling. Pathological results were compared with surgical findings or with long-term clinical and instrumental follow-ups. Success rates, sensitivity, specificity, accuracy, confidential intervals, positive predictive value and negative predictive value of the three percutaneous techniques in differentiating benign from malignant disease were assessed. The agreement coefficient of biopsy and brushing with final diagnosis was calculated using the Cohen's "K" value. Results Fifty-six patients had malignant strictures confirmed by surgery, histology, and by clinical follow-ups. Success rates of brushing, balloon surface sampling, and biopsy were 90.7, 100, and 100%, respectively. The comparative efficacy of brushing, balloon-surface sampling, and biopsy resulted as follows: sensitivity of 47.8, 87.5, and 92.1%, respectively; specificity of 100% for all the techniques; accuracy of 69.2, 91.7 and 93.6%, Positive Predictive Value of 100% for all the procedures and Negative Predictive Value of 55, 80, and 75%, respectively. Conclusions Percutaneous endoluminal biopsy is more accurate and sensitive than percutaneous bile duct

Book Review Who lives where. Habitability conditions of the population living in the great Andalusian cities / Reseña Del Libro Quién vive dónde. Las condiciones de habitabilidad de la población que vive en las grandes ciudades andaluzas

Directory of Open Access Journals (Sweden)

Diego Sánchez González

2016-09-01

Full Text Available Book Review Who lives where. Habitability conditions of the population living in the great Andalusian cities Reseña Del Libro Quién vive dónde. Las condiciones de habitabilidad de la población que vive en las grandes ciudades andaluzas

Assessment of Liver Remnant Using ICG Clearance Intraoperatively during Vascular Exclusion: Early Experience with the ALIIVE Technique

Directory of Open Access Journals (Sweden)

Lawrence Lau

2015-01-01

Full Text Available Background. The most significant risk following major hepatectomy is postoperative liver insufficiency. Current preoperative assessment of the future liver remnant relies upon assumptions which may not be valid in the setting of advanced resection strategies. This paper reports the feasibility of the ALIIVE technique which assesses the liver remnant with ICG clearance intraoperatively during vascular exclusion. Methods. 10 patients undergoing planned major liver resection (hemihepatectomy or greater were recruited. Routine preoperative assessment included CT and standardized volumetry. ICG clearance was measured noninvasively using a finger spectrophotometer at various time points including following parenchymal transection during inflow and outflow occlusion before vascular division, the ALIIVE step. Results. There were one case of mortality and three cases of posthepatectomy liver failure. The patient who died had the lowest ALIIVE ICG clearance (7.1%/min versus 14.4 ± 4.9. Routine preoperative CT and standardized volumetry did not predict outcome. Discussion/Conclusion. The novel ALIIVE technique is feasible and assesses actual future liver remnant function before the point of no return during major hepatectomy. This technique may be useful as a check step to offer a margin of safety to prevent posthepatectomy liver failure and death. Further confirmatory studies are required to determine a safety cutoff level.

Assessing performance of flaw characterization methods through uncertainty propagation

Science.gov (United States)

Miorelli, R.; Le Bourdais, F.; Artusi, X.

2018-04-01

In this work, we assess the inversion performance in terms of crack characterization and localization based on synthetic signals associated to ultrasonic and eddy current physics. More precisely, two different standard iterative inversion algorithms are used to minimize the discrepancy between measurements (i.e., the tested data) and simulations. Furthermore, in order to speed up the computational time and get rid of the computational burden often associated to iterative inversion algorithms, we replace the standard forward solver by a suitable metamodel fit on a database built offline. In a second step, we assess the inversion performance by adding uncertainties on a subset of the database parameters and then, through the metamodel, we propagate these uncertainties within the inversion procedure. The fast propagation of uncertainties enables efficiently evaluating the impact due to the lack of knowledge on some parameters employed to describe the inspection scenarios, which is a situation commonly encountered in the industrial NDE context.

Incorporating organizational factors into Probabilistic Risk Assessment (PRA) of complex socio-technical systems: A hybrid technique formalization

International Nuclear Information System (INIS)

Mohaghegh, Zahra; Kazemi, Reza; Mosleh, Ali

2009-01-01

This paper is a result of a research with the primary purpose of extending Probabilistic Risk Assessment (PRA) modeling frameworks to include the effects of organizational factors as the deeper, more fundamental causes of accidents and incidents. There have been significant improvements in the sophistication of quantitative methods of safety and risk assessment, but the progress on techniques most suitable for organizational safety risk frameworks has been limited. The focus of this paper is on the choice of 'representational schemes' and 'techniques.' A methodology for selecting appropriate candidate techniques and their integration in the form of a 'hybrid' approach is proposed. Then an example is given through an integration of System Dynamics (SD), Bayesian Belief Network (BBN), Event Sequence Diagram (ESD), and Fault Tree (FT) in order to demonstrate the feasibility and value of hybrid techniques. The proposed hybrid approach integrates deterministic and probabilistic modeling perspectives, and provides a flexible risk management tool for complex socio-technical systems. An application of the hybrid technique is provided in the aviation safety domain, focusing on airline maintenance systems. The example demonstrates how the hybrid method can be used to analyze the dynamic effects of organizational factors on system risk

Condition Assessment of Kevlar Composite Materials Using Raman Spectroscopy

Science.gov (United States)

Washer, Glenn; Brooks, Thomas; Saulsberry, Regor

2007-01-01

This viewgraph presentation includes the following main concepts. Goal: To evaluate Raman spectroscopy as a potential NDE tool for the detection of stress rupture in Kevlar. Objective: Test a series of strand samples that have been aged under various conditions and evaluate differences and trends in the Raman response. Hypothesis: Reduction in strength associated with stress rupture may manifest from changes in the polymer at a molecular level. If so, than these changes may effect the vibrational characteristics of the material, and consequently the Raman spectra produced from the material. Problem Statement: Kevlar composite over-wrapped pressure vessels (COPVs) on the space shuttles are greater than 25 years old. Stress rupture phenomena is not well understood for COPVs. Other COPVs are planned for hydrogen-fueled vehicles using Carbon composite material. Raman spectroscopy is being explored as an non-destructive evaluation (NDE) technique to predict the onset of stress rupture in Kevlar composite materials. Test aged Kevlar strands to discover trends in the Raman response. Strength reduction in Kevlar polymer will manifest itself on the Raman spectra. Conclusions: Raman spectroscopy has shown relative changes in the intensity and FWHM of the 1613 cm(exp -1) peak. Reduction in relative intensity for creep, fleet leader, and SIM specimens compared to the virgin strands. Increase in FWHM has been observed for the creep and fleet leader specimens compared to the virgin strands. Changes in the Raman spectra may result from redistributing loads within the material due to the disruption of hydrogen bonding between crystallites or defects in the crystallites from aging the Kevlar strands. Peak shifting has not been observed to date. Analysis is ongoing. Stress measurements may provide a tool in the short term.

Isotope-based immunological techniques. Their use in assessment of immune competence and the study of immune responses to pathogens

International Nuclear Information System (INIS)

Duffus, W.P.H.

1984-01-01

The influence of isotope-based techniques on both assessment of immune competence and immune response to pathogens is discussed. Immunodeficiencies acquired as a result of factors like malnutrition and concomitant disease can severely affect not only attempts to intensify and improve production but also successful immune response against important vaccines such as rinderpest and foot-and-mouth disease. Isotope-based techniques, with their accuracy, speed and small sample volume, are ideally suited for assessing immunocompetence. One of the main drawbacks remains antigen purity, an area where research should now be concentrated. Lymphocyte transformation is widely used to assess cell-mediated immuno-competence but techniques to assess biological functions such as phagocytosis and cell-mediated cytotoxicity could more usefully reflect immune status. These latter techniques utilize isotopes such as 3 H, 14 C, 32 P and 125 I. Investigation of specific cell-mediated immune response often requires a labelled target. Suitable isotopes such as 51 Cr, 99 Tcsup(m), 75 Se and 3 H are compared for their capacity to label both mammalian and parasite targets. Suggestions are made on a number of areas of research that might usefully be encouraged and supported in order to improve applied veterinary immunology in tropical countries. (author)

High-throughput tri-colour flow cytometry technique to assess Plasmodium falciparum parasitaemia in bioassays

DEFF Research Database (Denmark)

Tiendrebeogo, Regis W; Adu, Bright; Singh, Susheel K

2014-01-01

BACKGROUND: Unbiased flow cytometry-based methods have become the technique of choice in many laboratories for high-throughput, accurate assessments of malaria parasites in bioassays. A method to quantify live parasites based on mitotracker red CMXRos was recently described but consistent...... distinction of early ring stages of Plasmodium falciparum from uninfected red blood cells (uRBC) remains a challenge. METHODS: Here, a high-throughput, three-parameter (tri-colour) flow cytometry technique based on mitotracker red dye, the nucleic acid dye coriphosphine O (CPO) and the leucocyte marker CD45...... for enumerating live parasites in bioassays was developed. The technique was applied to estimate the specific growth inhibition index (SGI) in the antibody-dependent cellular inhibition (ADCI) assay and compared to parasite quantification by microscopy and mitotracker red staining. The Bland-Altman analysis...

Ultrasonic velocity measurements- a potential sensor for intelligent processing of austenitic stainless steels

International Nuclear Information System (INIS)

Venkadesan, S.; Palanichamy, P.; Vasudevan, M.; Baldev Raj

1996-01-01

Development of sensors based on Non-Destructive Evaluation (NDE) techniques for on-line sensing of microstructure and properties requires a thorough knowledge on the relation between the sensing mechanism/measurement of an NDE technique and the microstructure. As a first step towards developing an on-line sensor for studying the dynamic microstructural changes during processing of austenitic stainless steels, ultrasonic velocity measurements have been carried out to study the microstructural changes after processing. Velocity measurements could follow the progress of annealing starting from recovery, onset and completion of recrystallization, sense the differences in the microstructure obtained after hot deformation and estimate the grain size. This paper brings out the relation between the sensing method based on ultrasonic velocity measurements and the microstructure in austenitic stainless steel. (author)

SIIA: a knowledge-based assistant for the SAFT ultrasonic inspection system(a)

International Nuclear Information System (INIS)

Melton, R.B.; Doctor, S.R.; Taylor, T.T.; Badalamente, R.V.

1987-01-01

SIIA(b) is a knowledge-based system designed to assist in making the operation of the Synthetic Aperture Focussing Technique (SAFT) Ultrasonic Inspection System more reliable and efficient. This paper reports on their effort to develop a prototype version of SIIA to demonstrate the feasibility of using knowledge-based systems in nondestructive evaluation (NDE). The first section of the paper describes the structure of the problem and their conceptual design of the knowledge-based system. The next section describes the current state of the prototype SIIA system and relates some of their experiences in developing the system. The final section discusses their plans for future development of SIIA and the implications of this type of system for other NDE techniques and applications

Nondestructive Evaluation of the J-2X Direct Metal Laser Sintered Gas Generator Discharge Duct

Science.gov (United States)

Esther, Elizabeth A.; Beshears, Ronald D.; Lash, Rhonda K.

2012-01-01

The J-2X program at NASA's Marshall Space Flight Center (MSFC) procured a direct metal laser sintered (DMLS) gas generator discharge duct from Pratt & Whitney Rocketdyne and Morris Technologies for a test program that would evaluate the material properties and durability of the duct in an engine-like environment. DMLS technology was pursued as a manufacturing alternative to traditional techniques, which used off nominal practices to manufacture the gas generator duct's 180 degree turn geometry. MSFC's Nondestructive Evaluation (NDE) Team performed radiographic, ultrasonic, computed tomographic, and fluorescent penetrant examinations of the duct. Results from the NDE examinations reveal some shallow porosity but no major defects in the as-manufactured material. NDE examinations were also performed after hot-fire testing the gas generator duct and yielded similar results pre and post-test and showed no flaw growth or development.

Research and Teaching: Assessment of Graduate Teaching Assistants Enrolled in a Teaching Techniques Course

Science.gov (United States)

Zehnder, Caralyn

2016-01-01

At the authors' public liberal arts institution, biology masters students are required to enroll in BIOL 5050: Teaching Techniques. Course topics include designing effective lectures, assessment, classroom management, diversity in the classroom, and active learning strategies. The impact of this type of training on graduate students' attitudes and…

Mode of Delivery: A Classroom Assessment Technique Comparison between Verbal and Non-Verbal Communication

Science.gov (United States)