WorldWideScience

Sample records for natural input modal

  1. Load Estimation from Natural input Modal Analysis

    DEFF Research Database (Denmark)

    Aenlle, Manuel López; Brincker, Rune; Canteli, Alfonso Fernández

    2005-01-01

    One application of Natural Input Modal Analysis consists in estimating the unknown load acting on structures such as wind loads, wave loads, traffic loads, etc. In this paper, a procedure to determine loading from a truncated modal model, as well as the results of an experimental testing programme...... estimation. In the experimental program a small structure subjected to vibration was used to estimate the loading from the measurements and the experimental modal space. The modal parameters were estimated by Natural Input Modal Analysis and the scaling factors of the mode shapes obtained by the mass change...

  2. Determination of Stress Histories in Structures by Natural Input Modal Analysis

    DEFF Research Database (Denmark)

    Hjelm, Henrik P.; Brincker, Rune; Graugaard-Jensen, Jesper

    2005-01-01

    In this paper it is shown that stress histories can be estimated with high accuracy by integrating measured accelerations to obtain displacement and then performing a modal decomposition of the so estimated displacements. The relation between the modal coordinate and the stress in an arbitrary....... It is shown that the so estimated stress histories can replace strain gauge measurements in many cases, and it allows for an accurate estimation of fatigue damage....

  3. Modality of Input and Vocabulary Acquisition

    Directory of Open Access Journals (Sweden)

    Tetyana Sydorenko

    2010-06-01

    Full Text Available This study examines the effect of input modality (video, audio, and captions, i.e., on-screen text in the same language as audio on (a the learning of written and aural word forms, (b overall vocabulary gains, (c attention to input, and (d vocabulary learning strategies of beginning L2 learners. Twenty-six second-semester learners of Russian participated in this study. Group one (N = 8 saw video with audio and captions (VAC; group two (N = 9 saw video with audio (VA; group three (N = 9 saw video with captions (VC. All participants completed written and aural vocabulary tests and a final questionnaire.The results indicate that groups with captions (VAC and VC scored higher on written than on aural recognition of word forms, while the reverse applied to the VA group. The VAC group learned more word meanings than the VA group. Results from the questionnaire suggest that learners paid most attention to captions, followed by video and audio, and acquired most words by associating them with visual images. Pedagogical implications of this study are that captioned video tends to aid recognition of written word forms and the learning of word meaning, while non-captioned video tends to improve listening comprehension as it facilitates recognition of aural word forms.

  4. Modal Parameter Identification from Responses of General Unknown Random Inputs

    DEFF Research Database (Denmark)

    Ibrahim, S. R.; Asmussen, J. C.; Brincker, Rune

    1996-01-01

    Modal parameter identification from ambient responses due to a general unknown random inputs is investigated. Existing identification techniques which are based on assumptions of white noise and or stationary random inputs are utilized even though the inputs conditions are not satisfied....... This is accomplished via adding. In cascade. A force cascade conversion to the structures system under consideration. The input to the force conversion system is white noise and the output of which is the actual force(s) applied to the structure. The white noise input(s) and the structures responses are then used...

  5. Central Cross-Talk in Task Switching : Evidence from Manipulating Input-Output Modality Compatibility

    Science.gov (United States)

    Stephan, Denise Nadine; Koch, Iring

    2010-01-01

    Two experiments examined the role of compatibility of input and output (I-O) modality mappings in task switching. We define I-O modality compatibility in terms of similarity of stimulus modality and modality of response-related sensory consequences. Experiment 1 included switching between 2 compatible tasks (auditory-vocal vs. visual-manual) and…

  6. Competition and convergence between auditory and cross-modal visual inputs to primary auditory cortical areas

    Science.gov (United States)

    Mao, Yu-Ting; Hua, Tian-Miao

    2011-01-01

    Sensory neocortex is capable of considerable plasticity after sensory deprivation or damage to input pathways, especially early in development. Although plasticity can often be restorative, sometimes novel, ectopic inputs invade the affected cortical area. Invading inputs from other sensory modalities may compromise the original function or even take over, imposing a new function and preventing recovery. Using ferrets whose retinal axons were rerouted into auditory thalamus at birth, we were able to examine the effect of varying the degree of ectopic, cross-modal input on reorganization of developing auditory cortex. In particular, we assayed whether the invading visual inputs and the existing auditory inputs competed for or shared postsynaptic targets and whether the convergence of input modalities would induce multisensory processing. We demonstrate that although the cross-modal inputs create new visual neurons in auditory cortex, some auditory processing remains. The degree of damage to auditory input to the medial geniculate nucleus was directly related to the proportion of visual neurons in auditory cortex, suggesting that the visual and residual auditory inputs compete for cortical territory. Visual neurons were not segregated from auditory neurons but shared target space even on individual target cells, substantially increasing the proportion of multisensory neurons. Thus spatial convergence of visual and auditory input modalities may be sufficient to expand multisensory representations. Together these findings argue that early, patterned visual activity does not drive segregation of visual and auditory afferents and suggest that auditory function might be compromised by converging visual inputs. These results indicate possible ways in which multisensory cortical areas may form during development and evolution. They also suggest that rehabilitative strategies designed to promote recovery of function after sensory deprivation or damage need to take into

  7. Short-Term Memory in Mathematics-Proficient and Mathematics-Disabled Students as a Function of Input-Modality/Output-Modality Pairings.

    Science.gov (United States)

    Webster, Raymond E.

    1980-01-01

    A significant two-way input modality by output modality interaction suggested that short term memory capacity among the groups differed as a function of the modality used to present the items in combination with the output response required. (Author/CL)

  8. Modality

    DEFF Research Database (Denmark)

    Klinge, Alex; Müller, Henrik Høeg

    Modality: Studies in Form and Function reflects the diversity of theoretical frameworks and the heterogeneity of linguistic phenomena under the general heading of modality. Researchers in the fields of logic, philosophy and linguistics have for many years been pondering the elusive nature...... of modality and grappled with ways of capturing it. The 11 studies included here cover the span from contributions that seek to clarify controversial theoretical constructs to studies which take an empirical approach to linguistic categories and cross-linguistic typological issues. The key concepts addressed...

  9. Overview of multi-input frequency domain modal testing methods with an emphasis on sine testing

    Science.gov (United States)

    Rost, Robert W.; Brown, David L.

    1988-01-01

    An overview of the current state of the art multiple-input, multiple-output modal testing technology is discussed. A very brief review of the current time domain methods is given. A detailed review of frequency and spatial domain methods is presented with an emphasis on sine testing.

  10. Modeling recognition memory using the similarity structure of natural input

    NARCIS (Netherlands)

    Lacroix, J.P.W.; Murre, J.M.J.; Postma, E.O.; van den Herik, H.J.

    2006-01-01

    The natural input memory (NIM) model is a new model for recognition memory that operates on natural visual input. A biologically informed perceptual preprocessing method takes local samples (eye fixations) from a natural image and translates these into a feature-vector representation. During

  11. Modeling Recognition Memory Using the Similarity Structure of Natural Input

    Science.gov (United States)

    Lacroix, Joyca P. W.; Murre, Jaap M. J.; Postma, Eric O.; van den Herik, H. Jaap

    2006-01-01

    The natural input memory (NAM) model is a new model for recognition memory that operates on natural visual input. A biologically informed perceptual preprocessing method takes local samples (eye fixations) from a natural image and translates these into a feature-vector representation. During recognition, the model compares incoming preprocessed…

  12. On the Nature of the Input in Optimality Theory

    DEFF Research Database (Denmark)

    Heck, Fabian; Müller, Gereon; Vogel, Ralf

    2002-01-01

    The input has two main functions in optimality theory (Prince and Smolensky 1993). First, the input defines the candidate set, in other words it determines which output candidates compete for optimality, and which do not. Second, the input is referred to by faithfulness constraints that prohibit...... output candidates from deviating from specifications in the input. Whereas there is general agreement concerning the relevance of the input in phonology, the nature of the input in syntax is notoriously unclear. In this article, we show that the input should not be taken to define syntactic candidate...... and syntax is due to a basic, irreducible difference between these two components of grammar: Syntax is an information preserving system, phonology is not....

  13. Naturalizing aesthetics: brain areas for aesthetic appraisal across sensory modalities.

    Science.gov (United States)

    Brown, Steven; Gao, Xiaoqing; Tisdelle, Loren; Eickhoff, Simon B; Liotti, Mario

    2011-09-01

    We present here the most comprehensive analysis to date of neuroaesthetic processing by reporting the results of voxel-based meta-analyses of 93 neuroimaging studies of positive-valence aesthetic appraisal across four sensory modalities. The results demonstrate that the most concordant area of activation across all four modalities is the right anterior insula, an area typically associated with visceral perception, especially of negative valence (disgust, pain, etc.). We argue that aesthetic processing is, at its core, the appraisal of the valence of perceived objects. This appraisal is in no way limited to artworks but is instead applicable to all types of perceived objects. Therefore, one way to naturalize aesthetics is to argue that such a system evolved first for the appraisal of objects of survival advantage, such as food sources, and was later co-opted in humans for the experience of artworks for the satisfaction of social needs. Copyright © 2011 Elsevier Inc. All rights reserved.

  14. The functional upregulation of piriform cortex is associated with cross-modal plasticity in loss of whisker tactile inputs.

    Directory of Open Access Journals (Sweden)

    Bing Ye

    Full Text Available Cross-modal plasticity is characterized as the hypersensitivity of remaining modalities after a sensory function is lost in rodents, which ensures their awareness to environmental changes. Cellular and molecular mechanisms underlying cross-modal sensory plasticity remain unclear. We aim to study the role of different types of neurons in cross-modal plasticity.In addition to behavioral tasks in mice, whole-cell recordings at the excitatory and inhibitory neurons, and their two-photon imaging, were conducted in piriform cortex. We produced a mouse model of cross-modal sensory plasticity that olfactory function was upregulated by trimming whiskers to deprive their sensory inputs. In the meantime of olfactory hypersensitivity, pyramidal neurons and excitatory synapses were functionally upregulated, as well as GABAergic cells and inhibitory synapses were downregulated in piriform cortex from the mice of cross-modal sensory plasticity, compared with controls. A crosswire connection between barrel cortex and piriform cortex was established in cross-modal plasticity.An upregulation of pyramidal neurons and a downregulation of GABAergic neurons strengthen the activities of neuronal networks in piriform cortex, which may be responsible for olfactory hypersensitivity after a loss of whisker tactile input. This finding provides the clues for developing therapeutic strategies to promote sensory recovery and substitution.

  15. Age-Related Interference between the Selection of Input-Output Modality Mappings and Postural Control—a Pilot Study

    Science.gov (United States)

    Stelzel, Christine; Schauenburg, Gesche; Rapp, Michael A.; Heinzel, Stephan; Granacher, Urs

    2017-01-01

    Age-related decline in executive functions and postural control due to degenerative processes in the central nervous system have been related to increased fall-risk in old age. Many studies have shown cognitive-postural dual-task interference in old adults, but research on the role of specific executive functions in this context has just begun. In this study, we addressed the question whether postural control is impaired depending on the coordination of concurrent response-selection processes related to the compatibility of input and output modality mappings as compared to impairments related to working-memory load in the comparison of cognitive dual and single tasks. Specifically, we measured total center of pressure (CoP) displacements in healthy female participants aged 19–30 and 66–84 years while they performed different versions of a spatial one-back working memory task during semi-tandem stance on an unstable surface (i.e., balance pad) while standing on a force plate. The specific working-memory tasks comprised: (i) modality compatible single tasks (i.e., visual-manual or auditory-vocal tasks), (ii) modality compatible dual tasks (i.e., visual-manual and auditory-vocal tasks), (iii) modality incompatible single tasks (i.e., visual-vocal or auditory-manual tasks), and (iv) modality incompatible dual tasks (i.e., visual-vocal and auditory-manual tasks). In addition, participants performed the same tasks while sitting. As expected from previous research, old adults showed generally impaired performance under high working-memory load (i.e., dual vs. single one-back task). In addition, modality compatibility affected one-back performance in dual-task but not in single-task conditions with strikingly pronounced impairments in old adults. Notably, the modality incompatible dual task also resulted in a selective increase in total CoP displacements compared to the modality compatible dual task in the old but not in the young participants. These results suggest

  16. Distinct cortical areas for names of numbers and body parts independent of language and input modality.

    Science.gov (United States)

    Le Clec'H, G; Dehaene, S; Cohen, L; Mehler, J; Dupoux, E; Poline, J B; Lehéricy, S; van de Moortele, P F; Le Bihan, D

    2000-10-01

    Some models of word comprehension postulate that the processing of words presented in different modalities and languages ultimately converges toward common cerebral systems associated with semantic-level processing and that the localization of these systems may vary with the category of semantic knowledge being accessed. We used functional magnetic resonance imaging to investigate this hypothesis with two categories of words, numerals, and body parts, for which the existence of distinct category-specific areas is debated in neuropsychology. Across two experiments, one with a blocked design and the other with an event-related design, a reproducible set of left-hemispheric parietal and prefrontal areas showed greater activation during the manipulation of topographical knowledge about body parts and a right-hemispheric parietal network during the manipulation of numerical quantities. These results complement the existing neuropsychological and brain-imaging literature by suggesting that within the extensive network of bilateral parietal regions active during both number and body-part processing, a subset shows category-specific responses independent of the language and modality of presentation. Copyright 2000 Academic Press.

  17. Priming within and across modalities: exploring the nature of rCBF increases and decreases.

    Science.gov (United States)

    Badgaiyan, R D; Schacter, D L; Alpert, N M

    2001-02-01

    Neuroimaging studies suggest that within-modality priming is associated with reduced regional cerebral blood flow (rCBF) in the extrastriate area, whereas cross-modality priming is associated with increased rCBF in prefrontal cortex. To characterize the nature of rCBF changes in within- and cross-modality priming, we conducted two neuroimaging experiments using positron emission tomography (PET). In experiment 1, rCBF changes in within-modality auditory priming on a word stem completion task were observed under same- and different-voice conditions. Both conditions were associated with decreased rCBF in extrastriate cortex. In the different-voice condition there were additional rCBF changes in the middle temporal gyrus and prefrontal cortex. Results suggest that the extrastriate involvement in within-modality priming is sensitive to a change in sensory modality of target stimuli between study and test, but not to a change in the feature of a stimulus within the same modality. In experiment 2, we studied cross-modality priming on a visual stem completion test after encoding under full- and divided-attention conditions. Increased rCBF in the anterior prefrontal cortex was observed in the full- but not in the divided-attention condition. Because explicit retrieval is compromised after encoding under the divided-attention condition, prefrontal involvement in cross-modality priming indicates recruitment of an aspect of explicit retrieval mechanism. The aspect of explicit retrieval that is most likely to be involved in cross-modality priming is the familiarity effect. Copyright 2001 Academic Press.

  18. Multi-parameters sensitivity analysis of natural vibration modal for steel arch bridge

    Directory of Open Access Journals (Sweden)

    WANG Ying

    2014-02-01

    Full Text Available Because of the vehicle loads and environmental factors,the behaviors of bridge structure in service is becoming deterioration.The modal parameters are important indexes of structure,so sensitivity analysis of natural vibration is an important way to evaluate the behavior of bridge structure.In this paper,using the finite element software Ansys,calculation model of a steel arch bridge was built,and the natural vibration modals were obtained.In order to compare the different sensitivity of material parameters which may affect the natural vibration modal,5 factors were chosen to perform the calculation.The results indicated that different 5 factors had different sensitivity.The leading factor was elastic modulus of arch rib,and the elastic modulus of suspender had little effect to the sensitivity.Another argument was the opposite sensitivity effect happened between the elastic modulus and density of the material.

  19. Music and the Nature: Input of the Czech Composers

    Science.gov (United States)

    Nemec, Vaclav; Nemcova, Lidmila

    2014-05-01

    Extraordinary occasions for art of any kind - music, creative graphic and plastic arts, literature (classic, modern incl. science fiction), theatre, cinema, etc. - exist to harmonise individual personal interests with those of the humanity well-being and of the Nature and also to cultivate individual spirituality and the appropriate values. Arts can be applied as irreplaceable means for making any human being better, for improving his sense for solidarity and for increasing his ethical sensibility. An interest for the art should be cultivated already since the childhood. - How much of inspiration for numerous composers all over the world has been given by the Nature, how much of inspiration for people who by listening to such a music are increasing nobility of their behaviour as well as their friendly approach to the Nature. - Many classical music works have been written with a strong inspiration by the Nature itself from the past until today. The actual Year of the Czech Music gives the possibility to present the most famous Czech composers inspired by the Nature (selected examples only): Bedřich Smetana (1824 - 1884): At the sea shore - a concert etude for piano inspired by his stay in Göteborg (Sweden); Vltava (Moldau) - a symphonic poem from the cycle "My country" inspired by the river crossing Bohemia from the South to Prague; From the Bohemian woods and meadows - another symphonic poem from the same cycle. Antonín Dvořák (1841 - 1904): V přírodě (In the Nature) - a work for orchestra Leoš Janáček (1854 - 1928): Příhody li\\vsky Bystrou\\vsky (The Cunning Little Vixen) - an opera situated mostly in a forest. Josef Bohuslav Foerster (1859-1951): Velké širé rodné lány (Big large native fields) - a choir for men singers inspired by the nature in the region where the composer as a boy from Prague was visiting his grand-father. Vítězslav Novák (1870 - 1949): In Tatra mountains - a symphonic poem expressing the author's passion for the famous

  20. Load Estimation from Modal Parameters

    DEFF Research Database (Denmark)

    Aenlle, Manuel López; Brincker, Rune; Fernández, Pelayo Fernández

    2007-01-01

    In Natural Input Modal Analysis the modal parameters are estimated just from the responses while the loading is not recorded. However, engineers are sometimes interested in knowing some features of the loading acting on a structure. In this paper, a procedure to determine the loading from a FRF m...

  1. Interactive natural language acquisition in a multi-modal recurrent neural architecture

    Science.gov (United States)

    Heinrich, Stefan; Wermter, Stefan

    2018-01-01

    For the complex human brain that enables us to communicate in natural language, we gathered good understandings of principles underlying language acquisition and processing, knowledge about sociocultural conditions, and insights into activity patterns in the brain. However, we were not yet able to understand the behavioural and mechanistic characteristics for natural language and how mechanisms in the brain allow to acquire and process language. In bridging the insights from behavioural psychology and neuroscience, the goal of this paper is to contribute a computational understanding of appropriate characteristics that favour language acquisition. Accordingly, we provide concepts and refinements in cognitive modelling regarding principles and mechanisms in the brain and propose a neurocognitively plausible model for embodied language acquisition from real-world interaction of a humanoid robot with its environment. In particular, the architecture consists of a continuous time recurrent neural network, where parts have different leakage characteristics and thus operate on multiple timescales for every modality and the association of the higher level nodes of all modalities into cell assemblies. The model is capable of learning language production grounded in both, temporal dynamic somatosensation and vision, and features hierarchical concept abstraction, concept decomposition, multi-modal integration, and self-organisation of latent representations.

  2. Holographic Raman tweezers controlled by multi-modal natural user interface

    International Nuclear Information System (INIS)

    Tomori, Zoltán; Keša, Peter; Nikorovič, Matej; Valušová, Eva; Antalík, Marián; Kaňka, Jan; Jákl, Petr; Šerý, Mojmír; Bernatová, Silvie; Zemánek, Pavel

    2016-01-01

    Holographic optical tweezers provide a contactless way to trap and manipulate several microobjects independently in space using focused laser beams. Although the methods of fast and efficient generation of optical traps are well developed, their user friendly control still lags behind. Even though several attempts have appeared recently to exploit touch tablets, 2D cameras, or Kinect game consoles, they have not yet reached the level of natural human interface. Here we demonstrate a multi-modalnatural user interface’ approach that combines finger and gaze tracking with gesture and speech recognition. This allows us to select objects with an operator’s gaze and voice, to trap the objects and control their positions via tracking of finger movement in space and to run semi-automatic procedures such as acquisition of Raman spectra from preselected objects. This approach takes advantage of the power of human processing of images together with smooth control of human fingertips and downscales these skills to control remotely the motion of microobjects at microscale in a natural way for the human operator. (paper)

  3. Natural cycles and agricultural inputs: a farm gate Ecological Footprint analysis

    Science.gov (United States)

    Passeri, Nicolo; Blasi, Emanuele; Borucke, Michael; Galli, Alessandro; Franco, Silvio

    2014-05-01

    Land suitability for different crops depends on soil, water and climate conditions, as well as farmers' cultivation choices. Moreover, the use of agricultural inputs affects the natural cycles of crops and impacts their production. By assessing the ecological performance of farms as influenced by crop types, cultivation choices and land suitability one can therefore evaluate the effectiveness of agricultural practices and governance's options. Ecological Footprint accounts can be used to measure such ecological performance. These accounts track human demand for natural resources and ecological services and compare this demand with nature ability to regenerate these resource and services. This regenerative capacity is called biocapacity. Both demand (Footprint) and supply (biocapacity) are expressed in global hectares. Farming different from most other human activities, not only uses natural resources, but also enhances or erodes ecological supply. It therefore affects all factors that determine both Footprint and biocapacity. Climate, farmers' skills and choices (fertilizers, pesticides, machines) determine crop productivity, and to what extent crops preserve or compromise soils. The aim of this work is to evaluate how farmer's choices affect resources overexploitation. The study analysed how the use of inputs influences natural cycles within farm boundaries. This result from a pilot case study will show how particular farming practices affect both the farm's biocapacity and Ecological Footprint. Such analysis is relevant for informing involved stakeholders, namely the farmers on more sustainable agricultural practices and the policy makers on more suitable agricultural policies.

  4. An investigation of developmental changes in interpretation and construction of graphic AAC symbol sequences through systematic combination of input and output modalities.

    Science.gov (United States)

    Trudeau, Natacha; Sutton, Ann; Morford, Jill P

    2014-09-01

    While research on spoken language has a long tradition of studying and contrasting language production and comprehension, the study of graphic symbol communication has focused more on production than comprehension. As a result, the relationships between the ability to construct and to interpret graphic symbol sequences are not well understood. This study explored the use of graphic symbol sequences in children without disabilities aged 3;0 to 6;11 (years; months) (n=111). Children took part in nine tasks that systematically varied input and output modalities (speech, action, and graphic symbols). Results show that in 3- and 4-year-olds, attributing meaning to a sequence of symbols was particularly difficult even when the children knew the meaning of each symbol in the sequence. Similarly, while even 3- and 4-year-olds could produce a graphic symbol sequence following a model, transposing a spoken sentence into a graphic sequence was more difficult for them. Representing an action with graphic symbols was difficult even for 5-year-olds. Finally, the ability to comprehend graphic-symbol sequences preceded the ability to produce them. These developmental patterns, as well as memory-related variables, should be taken into account in choosing intervention strategies with young children who use AAC.

  5. Natural and anthropogenic hydrocarbon inputs to sediments of Patos Lagoon Estuary, Brazil.

    Science.gov (United States)

    Medeiros, Patricia Matheus; Bícego, Márcia Caruso; Castelao, Renato Menezes; Del Rosso, Clarissa; Fillmann, Gilberto; Zamboni, Ademilson Josemar

    2005-01-01

    The Patos Lagoon Estuary, southern Brazil, is an area of environmental interest not only because of tourism, but also because of the presence of the second major port of Brazil, with the related industrial and shipping activities. Thus, potential hydrocarbon pollution was examined in this study. Sediment samples were collected at 10 sites in the estuary, extracted, and analyzed by GC-FID and GC-MS for composition and concentration of the following organic geochemical markers: normal and isoprenoid alkanes, petroleum biomarkers, linear alkylbenzenes (LABs), and polycyclic aromatic hydrocarbons (PAHs). The total concentrations varied from 1.1 to 129.6 microg g(-1) for aliphatic hydrocarbons, from 17.8 to 4510.6 ng g(-1) for petroleum biomarkers, from 3.2 to 1601.9 ng g(-1) for LABs, and from 37.7 to 11,779.9 ng g(-1) for PAHs. Natural hydrocarbons were mainly derived from planktonic inputs due to a usual development of blooms in the estuary. Terrestrial plant wax compounds prevailed at sites located far from Rio Grande City and subject to stronger currents. Anthropogenic hydrocarbons are related to combustion/pyrolysis processes of fossil fuel, release of unburned oil products and domestic/industrial waste outfalls. Anthropogenic hydrocarbon inputs were more apparent at sites associated with industrial discharges (petroleum distributor and refinery), shipping activities (dry docking), and sewage outfalls (sewage). The overall concentrations of anthropogenic hydrocarbons revealed moderate to high hydrocarbon pollution in the study area.

  6. Modal Logics with Counting

    Science.gov (United States)

    Areces, Carlos; Hoffmann, Guillaume; Denis, Alexandre

    We present a modal language that includes explicit operators to count the number of elements that a model might include in the extension of a formula, and we discuss how this logic has been previously investigated under different guises. We show that the language is related to graded modalities and to hybrid logics. We illustrate a possible application of the language to the treatment of plural objects and queries in natural language. We investigate the expressive power of this logic via bisimulations, discuss the complexity of its satisfiability problem, define a new reasoning task that retrieves the cardinality bound of the extension of a given input formula, and provide an algorithm to solve it.

  7. Meditations on Metaphysical Modality

    OpenAIRE

    Willis, Edmund Lindsay James

    2011-01-01

    Although metaphysical modality has been much discussed and exploited by philosophers, its precise nature is often left unanalysed and obscure. This dissertation marks an attempt to understand it better. After examining modality in general, the specific topic is introduced through consideration of the views of Kripke and Lewis. Comparisons are then made with logical, scientific and conceptual modalities. Finally, it is argued that metaphysical modality is that variety of modality which is alet...

  8. Phosphorus cycling in natural and low input soil/plant systems: the role of soil microorganisms

    Science.gov (United States)

    Tamburini, F.; Bünemann, E. K.; Oberson, A.; Bernasconi, S. M.; Frossard, E.

    2011-12-01

    was faster in the P-free treatment. Laboratory incubation also showed a more rapid P uptake by microbial biomass in the NK than in the NPK treatment (37% and 6% of added 33P recovered in microbial P after 100 minutes in NK and NPK, respectively). The seasonal microbial P flux in both treatments was 1.5-4 times larger than the annual plant P uptake. In field studies carried out on highly weathered low P soils in Colombia, the comparison between grass-legume and grass-only pastures showed that the presence of legumes had an impact on the overall biological activity. In fact, microbial biomass and phosphatase activity were significantly larger in grass-legume pastures than in the legume-free experiments. Larger release of Pi from the organic P pool improved P availability to plants and pointed at a modified C:N:P stoichiometry along pathways of the nutrient cycle in the soil/plant system. All these data are evidence of a highly dynamic microbial P pool, which controls Pi concentration and, hence, availability for plants in natural and low input agricultural ecosystems.

  9. Three-dimensional imaging of flat natural and cultural heritage objects by a Compton scattering modality

    Science.gov (United States)

    Guerrero Prado, Patricio; Nguyen, Mai K.; Dumas, Laurent; Cohen, Serge X.

    2017-01-01

    Characterization and interpretation of flat ancient material objects, such as those found in archaeology, paleoenvironments, paleontology, and cultural heritage, have remained a challenging task to perform by means of conventional x-ray tomography methods due to their anisotropic morphology and flattened geometry. To overcome the limitations of the mentioned methodologies for such samples, an imaging modality based on Compton scattering is proposed in this work. Classical x-ray tomography treats Compton scattering data as noise in the image formation process, while in Compton scattering tomography the conditions are set such that Compton data become the principal image contrasting agent. Under these conditions, we are able, first, to avoid relative rotations between the sample and the imaging setup, and second, to obtain three-dimensional data even when the object is supported by a dense material by exploiting backscattered photons. Mathematically this problem is addressed by means of a conical Radon transform and its inversion. The image formation process and object reconstruction model are presented. The feasibility of this methodology is supported by numerical simulations.

  10. Hydrologic connectivity to streams increases nitrogen and phosphorus inputs and cycling in soils of created and natural floodplain wetlands

    Science.gov (United States)

    Wolf, Kristin L.; Noe, Gregory; Ahn, Changwoo

    2013-01-01

    Greater connectivity to stream surface water may result in greater inputs of allochthonous nutrients that could stimulate internal nitrogen (N) and phosphorus (P) cycling in natural, restored, and created riparian wetlands. This study investigated the effects of hydrologic connectivity to stream water on soil nutrient fluxes in plots (n = 20) located among four created and two natural freshwater wetlands of varying hydrology in the Piedmont physiographic province of Virginia. Surface water was slightly deeper; hydrologic inputs of sediment, sediment-N, and ammonium were greater; and soil net ammonification, N mineralization, and N turnover were greater in plots with stream water classified as their primary water source compared with plots with precipitation or groundwater as their primary water source. Soil water-filled pore space, inputs of nitrate, and soil net nitrification, P mineralization, and denitrification enzyme activity (DEA) were similar among plots. Soil ammonification, N mineralization, and N turnover rates increased with the loading rate of ammonium to the soil surface. Phosphorus mineralization and ammonification also increased with sedimentation and sediment-N loading rate. Nitrification flux and DEA were positively associated in these wetlands. In conclusion, hydrologic connectivity to stream water increased allochthonous inputs that stimulated soil N and P cycling and that likely led to greater retention of sediment and nutrients in created and natural wetlands. Our findings suggest that wetland creation and restoration projects should be designed to allow connectivity with stream water if the goal is to optimize the function of water quality improvement in a watershed.

  11. NIF Periscope Wall Modal Study Comparison of Results for 2 FEA Models with 2 Modal Tests

    International Nuclear Information System (INIS)

    Eli, M W; Gerhard, M A; Lee, C L; Sommer, S C; Woehrle, T G

    2000-01-01

    This report summarizes experimentally and numerically determined modal properties for one of the reinforced concrete end walls of the NIF Periscope Support Structure in Laser Bay 1. Two methods were used to determine these modal properties: (1) Computational finite-element analyses (modal extraction process); and (2) Experimental modal analysis based on measured test data. This report also includes experimentally determined modal properties for a prototype LM3/Polarizer line-replaceable unit (LRU) and a prototype PEPC LRU. Two important parameters, used during the design phase, are validated through testing [ref 1]. These parameters are the natural frequencies and modal damping (of the system in question) for the first several global modes of vibration. Experimental modal testing provides these modal values, along with the corresponding mode shapes. Another important parameter, the input excitation (expected during normal operation of the NIF laser system) [ref 1], can be verified by performing a series of ambient vibration measurements in the vicinity of the particular system (or subsystem) of interest. The topic of ambient input excitation will be covered in a separate report. Due to the large mass of the Periscope Pedestal, it is difficult to excite the entire series of Periscope Pedestal Walls all at once. It was decided that the experimental modal tests would be performed on just one Periscope End Wall in Laser Bay 1. Experimental modal properties for the Periscope End Wall have been used to validate and update the FE analyses. Results from the analyses and modal tests support the conclusion that the Periscope Pedestal will not exceed the stability budget, which is described in reference 1. The results of the modal tests for the Periscope End Wall in Laser Bay 1 have provided examples of modal properties that can be derived from future modal tests of the entire Periscope Assembly (excluding the LRU's). This next series of larger modal tests can be performed

  12. Natural frequencies, modeshapes and modal interactions for strings vibrating against an obstacle: Relevance to Sitar and Veena

    Science.gov (United States)

    Mandal, A. K.; Wahi, P.

    2015-03-01

    We study the vibration characteristics of a string with a smooth unilateral obstacle placed at one of the ends similar to the strings in musical instruments like sitar and veena. In particular, we explore the correlation between the string vibrations and some unique sound characteristics of these instruments like less inharmonicity in the frequencies, a large number of overtones and the presence of both frequency and amplitude modulations. At the obstacle, we have a moving boundary due to the wrapping of the string and an appropriate scaling of the spatial variable leads to a fixed boundary at the cost of introducing nonlinearity in the governing equation. Reduced order system of equations has been obtained by assuming a functional form for the string displacement which satisfies all the boundary conditions and gives the free length of the string in terms of the modal coordinates. To study the natural frequencies and mode-shapes, the nonlinear governing equation is linearized about the static configuration. The natural frequencies have been found to be harmonic and they depend on the shape of the obstacle through the effective free length of the string. Expressions have been obtained for the time-varying mode-shapes as well as the variation of the nodal points. Modal interactions due to coupling have been studied which show the appearance of higher overtones as well as amplitude modulations in our theoretical model akin to the experimental observations. All the obtained results have been verified with an alternate formulation based on the assumed mode method with polynomial shape functions.

  13. The perceptual nature of the cross-modal priming effect: arguments in favor of a sensory-based conception of memory.

    Science.gov (United States)

    Vallet, Guillaume; Brunel, Lionel; Versace, Rémy

    2010-01-01

    The aim of this study was to demonstrate that the cross-modal priming effect is perceptual and therefore consistent with the idea that knowledge is modality dependent. We used a two-way cross-modal priming paradigm in two experiments. These experiments were constructed on the basis of a two-phase priming paradigm. In the study phase of Experiment 1, participants had to categorize auditory primes as "animal" or "artifact". In the test phase, they had to perform the same categorization task with visual targets which corresponded either to the auditory primes presented in the study phase (old items) or to new stimuli (new items). To demonstrate the perceptual nature of the cross-modal priming effect, half of the auditory primes were presented with a visual mask (old-masked items). In the second experiment, the visual stimuli were used as primes and the auditory stimuli as targets, and half of the visual primes were presented with an auditory mask (a white noise). We hypothesized that if the cross-modal priming effect results from an activation of modality-specific representations, then the mask should interfere with the priming effect. In both experiments, the results corroborated our predictions. In addition, we observed a cross-modal priming effect from pictures to sounds in a long-term paradigm for the first time.

  14. Hydrologic connectivity to streams increases nitrogen and phosphorus inputs and cycling in soils of created and natural floodplain wetlands.

    Science.gov (United States)

    Wolf, Kristin L; Noe, Gregory B; Ahn, Changwoo

    2013-07-01

    Greater connectivity to stream surface water may result in greater inputs of allochthonous nutrients that could stimulate internal nitrogen (N) and phosphorus (P) cycling in natural, restored, and created riparian wetlands. This study investigated the effects of hydrologic connectivity to stream water on soil nutrient fluxes in plots ( = 20) located among four created and two natural freshwater wetlands of varying hydrology in the Piedmont physiographic province of Virginia. Surface water was slightly deeper; hydrologic inputs of sediment, sediment-N, and ammonium were greater; and soil net ammonification, N mineralization, and N turnover were greater in plots with stream water classified as their primary water source compared with plots with precipitation or groundwater as their primary water source. Soil water-filled pore space, inputs of nitrate, and soil net nitrification, P mineralization, and denitrification enzyme activity (DEA) were similar among plots. Soil ammonification, N mineralization, and N turnover rates increased with the loading rate of ammonium to the soil surface. Phosphorus mineralization and ammonification also increased with sedimentation and sediment-N loading rate. Nitrification flux and DEA were positively associated in these wetlands. In conclusion, hydrologic connectivity to stream water increased allochthonous inputs that stimulated soil N and P cycling and that likely led to greater retention of sediment and nutrients in created and natural wetlands. Our findings suggest that wetland creation and restoration projects should be designed to allow connectivity with stream water if the goal is to optimize the function of water quality improvement in a watershed. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

  15. A simple technique for obtaining future climate data inputs for natural resource models

    Science.gov (United States)

    Those conducting impact studies using natural resource models need to be able to quickly and easily obtain downscaled future climate data from multiple models, scenarios, and timescales for multiple locations. This paper describes a method of quickly obtaining future climate data over a wide range o...

  16. Selecting the Best Mobile Information Service with Natural Language User Input

    Science.gov (United States)

    Feng, Qiangze; Qi, Hongwei; Fukushima, Toshikazu

    Information services accessed via mobile phones provide information directly relevant to subscribers’ daily lives and are an area of dynamic market growth worldwide. Although many information services are currently offered by mobile operators, many of the existing solutions require a unique gateway for each service, and it is inconvenient for users to have to remember a large number of such gateways. Furthermore, the Short Message Service (SMS) is very popular in China and Chinese users would prefer to access these services in natural language via SMS. This chapter describes a Natural Language Based Service Selection System (NL3S) for use with a large number of mobile information services. The system can accept user queries in natural language and navigate it to the required service. Since it is difficult for existing methods to achieve high accuracy and high coverage and anticipate which other services a user might want to query, the NL3S is developed based on a Multi-service Ontology (MO) and Multi-service Query Language (MQL). The MO and MQL provide semantic and linguistic knowledge, respectively, to facilitate service selection for a user query and to provide adaptive service recommendations. Experiments show that the NL3S can achieve 75-95% accuracies and 85-95% satisfactions for processing various styles of natural language queries. A trial involving navigation of 30 different mobile services shows that the NL3S can provide a viable commercial solution for mobile operators.

  17. Modeling imbalanced economic recovery following a natural disaster using input-output analysis.

    Science.gov (United States)

    Li, Jun; Crawford-Brown, Douglas; Syddall, Mark; Guan, Dabo

    2013-10-01

    Input-output analysis is frequently used in studies of large-scale weather-related (e.g., Hurricanes and flooding) disruption of a regional economy. The economy after a sudden catastrophe shows a multitude of imbalances with respect to demand and production and may take months or years to recover. However, there is no consensus about how the economy recovers. This article presents a theoretical route map for imbalanced economic recovery called dynamic inequalities. Subsequently, it is applied to a hypothetical postdisaster economic scenario of flooding in London around the year 2020 to assess the influence of future shocks to a regional economy and suggest adaptation measures. Economic projections are produced by a macro econometric model and used as baseline conditions. The results suggest that London's economy would recover over approximately 70 months by applying a proportional rationing scheme under the assumption of initial 50% labor loss (with full recovery in six months), 40% initial loss to service sectors, and 10-30% initial loss to other sectors. The results also suggest that imbalance will be the norm during the postdisaster period of economic recovery even though balance may occur temporarily. Model sensitivity analysis suggests that a proportional rationing scheme may be an effective strategy to apply during postdisaster economic reconstruction, and that policies in transportation recovery and in health care are essential for effective postdisaster economic recovery. © 2013 Society for Risk Analysis.

  18. Influence of input data on airflow network accuracy in residential buildings with natural wind- and stack-driven ventilation

    Institute of Scientific and Technical Information of China (English)

    Krzysztof Arendt; Marek Krzaczek; Jacek Tejchman

    2017-01-01

    The airflow network (AFN) modeling approach provides an attractive balance between the accuracy and computational demand for naturally ventilated buildings. Its accuracy depends on input parameters such as wind pressure and opening discharge coefficients. In most cases, these parameters are obtained from secondary sources which are solely representative for very simplified buildings, i.e. for buildings without facade details. Although studies comparing wind pressure coefficients or discharge coefficients from different sources exist, the knowledge regarding the effect of input data on AFN is still poor. In this paper, the influence of wind pressure data on the accuracy of a coupled AFN-BES model for a real building with natural wind- and stack-driven ventilation was analyzed. The results of 8 computation cases with different wind pressure data from secondary sources were compared with the measured data. Both the indoor temperatures and the airflow were taken into account. The outcomes indicated that the source of wind pressure data had a significant influence on the model performance.

  19. Toward predicate approaches to modality

    CERN Document Server

    Stern, Johannes

    2016-01-01

    In this volume, the author investigates and argues for, a particular answer to the question: What is the right way to logically analyze modalities from natural language within formal languages? The answer is: by formalizing modal expressions in terms of predicates. But, as in the case of truth, the most intuitive modal principles lead to paradox once the modal notions are conceived as predicates. The book discusses the philosophical interpretation of these modal paradoxes and argues that any satisfactory approach to modality will have to face the paradoxes independently of the grammatical category of the modal notion. By systematizing modal principles with respect to their joint consistency and inconsistency, Stern provides an overview of the options and limitations of the predicate approach to modality that may serve as a useful starting point for future work on predicate approaches to modality. Stern also develops a general strategy for constructing philosophically attractive theories of modal notions conce...

  20. Assessment of multiple sources of anthropogenic and natural chemical inputs to a morphologically complex basin, Lake Mead, USA

    Science.gov (United States)

    Rosen, Michael R.; Van Metre, P.C.

    2010-01-01

    Lakes with complex morphologies and with different geologic and land-use characteristics in their sub-watersheds could have large differences in natural and anthropogenic chemical inputs to sub-basins in the lake. Lake Mead in southern Nevada and northern Arizona, USA, is one such lake. To assess variations in chemical histories from 1935 to 1998 for major sub-basins of Lake Mead, four sediment cores were taken from three different parts of the reservoir (two from Las Vegas Bay and one from the Overton Arm and Virgin Basin) and analyzed for major and trace elements, radionuclides, and organic compounds. As expected, anthropogenic contaminant inputs are greatest to Las Vegas Bay reflecting inputs from the Las Vegas urban area, although concentrations are low compared to sediment quality guidelines and to other USA lakes. One exception to this pattern was higher Hg in the Virgin Basin core. The Virgin Basin core is located in the main body of the lake (Colorado River channel) and is influenced by the hydrology of the Colorado River, which changed greatly with completion of Glen Canyon Dam upstream in 1963. Major and trace elements in the core show pronounced shifts in the early 1960s and, in many cases, gradually return to concentrations more typical of pre-1960s by the 1980s and 1990s, after the filling of Lake Powell. The Overton Arm is the sub-basin least effected by anthropogenic contaminant inputs but has a complex 137Cs profile with a series of large peaks and valleys over the middle of the core, possibly reflecting fallout from nuclear tests in the 1950s at the Nevada Test Site. The 137Cs profile suggests a much greater sedimentation rate during testing which we hypothesize results from greatly increased dust fall on the lake and Virgin and Muddy River watersheds. The severe drought in the southwestern USA during the 1950s might also have played a role in variations in sedimentation rate in all of the cores. ?? 2009.

  1. Historical and Paleo Events as an input for Seismic And Associated Natural Hazard Assessment of Javakheti highland (South Georgia)

    Science.gov (United States)

    Elashvili, M.; Javakhishvili, Z.; Godoladze, T.; Karakhanyan, A.; Sukhishvili, L.; Nikolaeva, E.; Sokhadze, G.; Avanesyan, M.

    2012-12-01

    of historical earthquakes of 1899 and 1089, as well as Archaeo-Seismological site along the Javakheti seismic fault will be presented. History on Natural Disasters in the region can be complemented by Bertakana Paleo-Landslide, to be discussed separately as one of the mega events in the Area. The mentioned events are considered as an important input for Seismic Hazard Assessment of Javakheti Region.

  2. Response Modality Variations Affect Determinations of Children's Learning Styles.

    Science.gov (United States)

    Janowitz, Jeffrey M.

    The Swassing-Barbe Modality Index (SBMI) uses visual, auditory, and tactile inputs, but only reconstructed output, to measure children's modality strengths. In this experiment, the SBMI's three input modalities were crossed with two output modalities (spoken and drawn) in addition to the reconstructed standard to result in nine treatment…

  3. Evaluating natural and anthropogenic trace element inputs along an alpine to urban gradient in the Provo River, Utah, USA

    International Nuclear Information System (INIS)

    Carling, Gregory T.; Tingey, David G.; Fernandez, Diego P.; Nelson, Stephen T.; Aanderud, Zachary T.; Goodsell, Timothy H.; Chapman, Tucker R.

    2015-01-01

    Numerous natural and anthropogenic processes in a watershed produce the geochemical composition of a river, which can be altered over time by snowmelt and rainfall events and by built infrastructure (i.e., dams and diversions). Trace element concentrations coupled with isotopic ratios offer valuable insights to disentangle the effects of these processes on water quality. In this study, we measured a suite of 40+ trace and major elements (including As, Cd, Ce, Cr, Cs, Fe, La, Li, Mo, Pb, Rb, Sb, Se, Sr, Ti, Tl, U, and Zn), Sr isotopes ("8"7Sr/"8"6Sr), and stable isotopes of H and O (δD and δ"1"8O) to investigate natural and anthropogenic processes impacting the Provo River in northern Utah, USA. The river starts as a pristine mountain stream and passes through agricultural and urban areas, with two major reservoirs and several major diversions to and from the river. We sampled the entire 120 km length of the Provo River at 13 locations from the Uinta Mountains to Utah Valley, as well as two important tributaries, across the range of hydrologic conditions from low flow to snowmelt runoff during the 2013 water year. We also sampled the furthest downstream site in the Utah Valley urban area during a major flood event. Trace element concentrations indicate that a variety of factors potentially influence Provo River chemistry, including inputs from weathering of carbonate/siliciclastic rocks (Sr) and black shales (Se and U), geothermal groundwater (As, Cs, Li, and Rb), soil erosion during snowmelt runoff (Ce, Cr, Fe, La, Pb, and Ti), legacy mining operations (Mo, Sb, and Tl), and urban runoff (Cr, Pb, and Zn). Although specific elements overlap between different groups, the combination of different elements together with isotopic measurements and streamflow observations may act as diagnostic tools to identify sources. "8"7Sr/"8"6Sr ratios indicate a strong influence of siliciclastic bedrock in the headwaters with values exceeding 0.714 and carbonate bedrock in the

  4. On the functional vs. lexical nature of restructuring heads: evidence for a fine-grained classification of restructuring modals

    Directory of Open Access Journals (Sweden)

    Irene Balza

    2012-05-01

    Full Text Available This paper examines in detail the thematic and syntactic properties of a set of (non-restructuring structures in Germanic, Romance and Basque. Based on the comparison of these structures, I propose a fine-grained classification of (non-restructuring constructions that include Functional Restructuring, Semi-Lexical Restructuring, Lexical Restructuring and Non-Restructuring constructions. The four types involve complements of different underlying structures (VPs, vPs or even as large as NegP/TPs. The results of the analysis argue against Cinque’s (2005 hypothesis that all restructuring verbs are exclusively functional, and contradicts Wurmbrand’s (1999 claim that, within the mixed class of restructuring verbs, modals must be raising verbs.

  5. Modal Based Fatigue Monitoring of Steel Structures

    DEFF Research Database (Denmark)

    Graugaard-Jensen, J.; Brincker, Rune; Hjelm, H. P.

    2005-01-01

    In this paper it is shown how the accumulated fatigue in steel structures can be estimated with high accuracy by continuously measuring the accelerations in a few points of the structure. First step is to obtain a good estimate of the mode shapes by performing a natural input modal analysis. The so...... by applying the mode shapes of the calibrated Finite Element model and strains are obtained using the shape functions for the actual elements. The technique has been applied on a model frame structure in the laboratory and on a wind loaded lattice pylon structure. In both cases the estimated stresses has been...

  6. Modal identification of composite structures using Eigen realization method

    International Nuclear Information System (INIS)

    Hamidzadeh, H.R.; Afolabi, D.

    1996-01-01

    Experimental modal analysis has proved to be a useful tool to determine the vibration response of complex composite structures. An accurate method for extracting modal parameters of these type of structures are presented. The method used experimental impulse response of the system as input and provides natural frequencies and damping ratios of a dynamic system. The employed theories are Eigen Realization and Impulse Response methods. The adopted method is superior to other available methods in time and frequency domains. The presented method is proven to provide robustness with respect to measured noise

  7. Dust – A geology-orientated attempt to reappraise the natural components, amounts, inputs to sediment, and importance for correlation purposes

    Czech Academy of Sciences Publication Activity Database

    Hladil, Jindřich; Čejchan, Petr; Bábek, O.; Koptíková, Leona; Navrátil, Tomáš; Kubínová, Petra

    2010-01-01

    Roč. 13, č. 4 (2010), s. 367-384 ISSN 1374-8505 R&D Projects: GA AV ČR IAAX00130702 Institutional research plan: CEZ:AV0Z30130516 Keywords : natural dust * particulare matter * aerosol * sedimentary background * sedimentary inputs * dust teleconnection * limestones * iron contents * Holocene Subject RIV: DB - Geology ; Mineralogy Impact factor: 0.645, year: 2010 http://popups.ulg.ac.be/Geol/docannexe.php?id=3104

  8. Conceptual design study on very small long-life gas cooled fast reactor using metallic natural Uranium-Zr as fuel cycle input

    International Nuclear Information System (INIS)

    Monado, F.; Permana, S.

    2013-01-01

    Full-text: A conceptual design study of very small 350 MWth Gas-cooled Fast Reactors with Helium coolant has been performed. In this study Modified CANDLE burn-up scheme was implemented to create small and long life fast reactors with natural Uranium as fuel cycle input. Such system can utilize natural Uranium resources efficiently without the necessity of enrichment plant or reprocessing plant. The core with metallic fuel based was subdivided into 10 regions with the same volume. The fresh Natural Uranium is initially put in region-1, after one cycle of 10 years of burn-up it is shifted to region-2 and the each region-1 is filled by fresh Natural Uranium fuel. This concept is basically applied to all axial regions. The reactor discharge burn-up is 31.8 % HM. From the neutronic point of view, this design is in compliance with good performance. (author)

  9. Conceptual design study on very small long-life gas cooled fast reactor using metallic natural Uranium-Zr as fuel cycle input

    International Nuclear Information System (INIS)

    Monado, Fiber; Ariani, Menik; Su'ud, Zaki; Waris, Abdul; Basar, Khairul; Permana, Sidik; Aziz, Ferhat; Sekimoto, Hiroshi

    2014-01-01

    A conceptual design study of very small 350 MWth Gas-cooled Fast Reactors with Helium coolant has been performed. In this study Modified CANDLE burn-up scheme was implemented to create small and long life fast reactors with natural Uranium as fuel cycle input. Such system can utilize natural Uranium resources efficiently without the necessity of enrichment plant or reprocessing plant. The core with metallic fuel based was subdivided into 10 regions with the same volume. The fresh Natural Uranium is initially put in region-1, after one cycle of 10 years of burn-up it is shifted to region-2 and the each region-1 is filled by fresh Natural Uranium fuel. This concept is basically applied to all axial regions. The reactor discharge burn-up is 31.8% HM. From the neutronic point of view, this design is in compliance with good performance

  10. Observations on sediment sources in the Lower Athabasca River basin: implications of natural hydrocarbons inputs from oil sands deposits

    International Nuclear Information System (INIS)

    Conly, F.M.

    1999-01-01

    Government, industry and public concern exists over the environmental consequences of the development of the oil sand deposits in the McMurray Formation in the lower Athabasca River basin, Alberta. The impact of this development is unclear and is undergoing investigation. Investigations to date have focussed on the nature of the effluent produced by the extraction industry and its effect on biotic systems, and on the spatial distribution of hydrocarbon contaminants associated with deposited fluvial sediments. Natural hydrocarbon outcrops may be responsible for observed biomarker responses in areas not exposed to industrial effluent. Given this source of hydrocarbons and doubt concerning its environmental impact, it is difficult to ascertain the impact of oil extraction activities within a fluvial system. A study was conducted to determine the nature and extent of natural hydrocarbon releases within the context of the sediment regime of the lower Athabasca River basin. A description is included of observations from the field and a context is set up for assessing sediment-bound hydrocarbon contaminants in the lower Athabasca River basin. Abstract only included

  11. Key natural analogue input required to build a safety case for direct disposal of spent nuclear fuel in Japan

    Energy Technology Data Exchange (ETDEWEB)

    McKinley, I.G.; Hardie, S.M.L.; Klein, E. [MCM Consulting, Baden-Dättwil (Switzerland); Kawamura, H. [Obayashi Corporation, Nuclear Facilities Division, Tokyo (Japan); Beattie, T.M. [MCM Consulting, Bristol (United Kingdom)

    2015-06-15

    Natural analogues have been previously used to support the safety case for direct disposal of spent nuclear fuel, but the focus of such work was very dependent on the key barriers of specific national disposal concepts. Investigations of the feasibility of such disposal in Japan are at an early stage but, nevertheless, it is clear that building a robust safety case will be very challenging and would benefit from focused support from natural analogue studies—both in terms of developing/testing required models and, as importantly, presenting safety arguments to a wide range of stakeholders. This paper identifies key analogues that support both longevity and spread of failure times of massive steel overpacks, the effectiveness of buffering of radiolytic oxidants and the chemical and physical mechanisms retarding release of radionuclides from the engineered barriers. It is concluded that, for countries like Japan where performance needs to be assessed as realistically as possible, natural analogues can complement the existing laboratory and theoretical knowledge base and contribute towards development of a robust safety case. (authors)

  12. Input Calibration and Validation of RELAP5 Against CIRCUS-IV Single Channel Tests on Natural Circulation Two-Phase Flow Instability

    Directory of Open Access Journals (Sweden)

    Viet-Anh Phung

    2015-01-01

    Full Text Available RELAP5 is a system thermal-hydraulic code that is used to perform safety analysis on nuclear reactors. Since the code is based on steady state, two-phase flow regime maps, there is a concern that RELAP5 may provide significant errors for rapid transient conditions. In this work, the capability of RELAP5 code to predict the oscillatory behavior of a natural circulation driven, two-phase flow at low pressure is investigated. The simulations are compared with a series of experiments that were performed in the CIRCUS-IV facility at the Delft University of Technology. For this purpose, we developed a procedure for calibration of the input and code validation. The procedure employs (i multiple parameters measured in different regimes, (ii independent consideration of the subsections of the loop, and (iii assessment of importance of the uncertain input parameters. We found that predicted system parameters are less sensitive to variations of the uncertain input and boundary conditions in high frequency oscillations regime. It is shown that calculation results overlap experimental values, except for the high frequency oscillations regime where the maximum inlet flow rate was overestimated. This finding agrees with the idea that steady state, two-phase flow regime maps might be one of the possible reasons for the discrepancy in case of rapid transients in two-phase systems.

  13. Use of Pb and Sr isotopes as tracers of anthropogenic and natural inputs in rain waters and rivers of the Paris basin

    International Nuclear Information System (INIS)

    Roy, St.

    1996-06-01

    The isotopic composition of Pb and Sr, measured in the soluble phase of rain waters and rivers are used to determine and quantify the anthropogenic inputs and the weathering rates in the Seine basin. Atmospheric lead from rain waters is exclusively anthropogenic and is derived from gasoline and industrial emissions. These rain waters transfer lead, and certain other heavy metals, into the Seine, where the anthropogenic signal perturbs the natural geochemical cycle of these metals. This transfer to the river occurs principally in the city of Paris, in contrast, in the catchment area upstream of Paris, these elements are mainly trapped in soils, rather than transferred to the river. The anthropogenic inputs comprise three-quarters of the total transport of these metals by the Seine. In the river, lead transport is due to adsorption process occurring within the suspended load. Thus, soluble lead concentrations are linked to the river flow and the intensity of mechanical erosion. After correction for atmospheric and anthropogenic inputs, it is possible to estimate the silicate weathering rate for the Seine basin. This estimate is close to that obtained for large plain rivers, such as the Congo or Amazon, indicating that chemical erosion is linked to tectonic processes rather than climatic conditions. (author)

  14. Comparative study for axial and radial shuffling scheme effect on the performance of Pb-Bi cooled fast reactors with natural uranium as fuel cycle input

    International Nuclear Information System (INIS)

    Zaki Suud; Indah Rosidah; Maryam Afifah; Ferhat Aziz; Sekimoto, H.

    2013-01-01

    Full text:Comparative study for the Design of Pb-Bi cooled fast reactors with natural uranium as fuel cycle input using special radial shuffling strategy and axial direction modified CANDLE burn-up scheme has been performed. The reactors utilizes UN-PuN as fuel, Eutectic Pb-Bi as coolant, and can be operated without refueling for 10 years in each batch. Reactor design optimization is performed to utilize natural uranium as fuel cycle input. This reactor subdivided into 6-10 regions with equal volume in radial directions. The natural uranium is initially put in region 1, and after one cycle of 10 years of burn-up it is shifted to region 2 and the region 1 is filled by fresh natural uranium fuel. This concept is basically applied to all regions. The calculation has been done by using SRAC-Citation system code and JENDL-3.2 library. The effective multiplication factor change increases monotonously during 10 years reactor operation time. There is significant power distribution change in the central part of the core during the BOC and the EOC in the radial shuffling system. It is larger than that in the case of modified CANDLE case which use axial direction burning region move. The burn-up level of fuel is slowly grows during the first 15 years but then grow faster in the rest of burn-up history. This pattern is a little bit different from the case of modified CANDLE burn-up scheme in Axial direction in which the slow growing burn-up period is relatively longer almost half of the burn-up history. (author)

  15. Quantifying and managing uncertainty in operational modal analysis

    Science.gov (United States)

    Au, Siu-Kui; Brownjohn, James M. W.; Mottershead, John E.

    2018-03-01

    Operational modal analysis aims at identifying the modal properties (natural frequency, damping, etc.) of a structure using only the (output) vibration response measured under ambient conditions. Highly economical and feasible, it is becoming a common practice in full-scale vibration testing. In the absence of (input) loading information, however, the modal properties have significantly higher uncertainty than their counterparts identified from free or forced vibration (known input) tests. Mastering the relationship between identification uncertainty and test configuration is of great interest to both scientists and engineers, e.g., for achievable precision limits and test planning/budgeting. Addressing this challenge beyond the current state-of-the-art that are mostly concerned with identification algorithms, this work obtains closed form analytical expressions for the identification uncertainty (variance) of modal parameters that fundamentally explains the effect of test configuration. Collectively referred as 'uncertainty laws', these expressions are asymptotically correct for well-separated modes, small damping and long data; and are applicable under non-asymptotic situations. They provide a scientific basis for planning and standardization of ambient vibration tests, where factors such as channel noise, sensor number and location can be quantitatively accounted for. The work is reported comprehensively with verification through synthetic and experimental data (laboratory and field), scientific implications and practical guidelines for planning ambient vibration tests.

  16. The role of natural resource and environmental economics in determining the trade-offs in consumption and production of energy inputs: The case of biomass energy crops

    Energy Technology Data Exchange (ETDEWEB)

    Downing, M.; Graham, R.L.

    1993-12-31

    Natural resource economics issues deal with flows and funds of renewable and nonrenewable resources over time. These issues include topics concerned with management of fisheries, forests, mineral, energy resources, the extinction of species and the irreversibility of development over time. Environmental economics issues deal with regulation of polluting activities and the valuation of environmental amenities. In this study we outline a framework for studying both natural resource and environmental economics issues for any renewable or nonrenewable resource. Valuation from both the cost and benefit sides are addressed as they relate to the valuation of environmental programs or policies. By using this top-down approach to analyze and determine the costs and benefits of using renewable or nonrenewable resources, policy-makers on the global, national and local scales may be better informed as to the probable nonmarket and market ramifications of their natural resource and environmental policy decisions. This general framework for analysis is then focused to address biomass energy crops and their usage as inputs to energy production. As with any energy technology, a complete analysis must include an examination of the entire fuel cycle; specifically both production and consumption sides. From a production standpoint, market valuation issues such as crop management techniques, inputs to production, and community economics issues must be addressed as well as nonmarket valuation issues such as soil erosion, ground water effects and carbon sequestration. On the consumption side, market valuation considerations such as energy fuel efficiency and quality, cost of conversion and employment of labor are important factors while the critical nonmarket valuation factors are ambient air visibility, greenhouse gas release, and disposal of the by-products of conversion and combustion.

  17. The role of natural resource and environmental economics in determining the trade-offs in consumption and production of energy inputs: The case of biomass energy crops

    International Nuclear Information System (INIS)

    Downing , M.; Graham, R.L.

    1993-01-01

    Natural resource economics issues deal with flows and funds of renewable and nonrenewable resources over time. These issues include topics concerned with management of fisheries, forests, mineral, energy resources, the extinction of species and the irreversibility of development over time. Environmental economics issues deal with regulation of polluting activities and the valuation of environmental amenities. In this study we outline a framework for studying both natural resource and environmental economics issues for any renewable or nonrenewable resource. Valuation from both the cost and benefit sides are addressed as they relate to the valuation of environmental programs or policies. By using this top-down approach to analyze and determine the costs and benefits of using renewable or nonrenewable resources, policy-makers on the global, national and local scales may be better informed as to the probable nonmarket and market ramifications of their natural resource and environmental policy decisions. The general framework for analysis is then focused to address biomass energy crops and their usage as inputs to energy production. As with any energy technology, a complete analysis must include an examination of the entire fuel cycle; specifically both production and consumption sides. From a production standpoint, market valuation issues such as crop management techniques, inputs to production, and community economics issues must be addressed as well as nonmarket valuation issues such as soil erosion, ground water effects and carbon sequestration. On the consumption side, market valuation considerations such as energy fuel efficiency and quality, cost of conversion and employment of labor are important factors while the critical nonmarket valuation factors are ambient air visibility, greenhouse gas release, and disposal of the by-products of conversion and combustion

  18. Experimental modal analysis

    Energy Technology Data Exchange (ETDEWEB)

    Ibsen, Lars Bo; Liingaard, M.

    2006-12-15

    This technical report concerns the basic theory and principles for experimental modal analysis. The sections within the report are: Output-only modal analysis software, general digital analysis, basics of structural dynamics and modal analysis and system identification. (au)

  19. The study of capability natural uranium as fuel cycle input for long life gas cooled fast reactors with helium as coolant

    Energy Technology Data Exchange (ETDEWEB)

    Ariani, Menik, E-mail: menikariani@gmail.com; Satya, Octavianus Cakra; Monado, Fiber [Department of Physics, Faculty of Mathematics and Natural Sciences, Sriwijaya University, jl Palembang-Prabumulih km 32 Indralaya OganIlir, South of Sumatera (Indonesia); Su’ud, Zaki [Nuclear and Biophysics Research Division, Faculty of Mathematics and Natural Sciences, Bandung Institute of Technology, jlGanesha 10, Bandung (Indonesia); Sekimoto, Hiroshi [CRINES, Tokyo Institute of Technology, 2-12-11N1-17 Ookayama, Meguro-Ku, Tokyo (Japan)

    2016-03-11

    The objective of the present research is to assess the feasibility design of small long-life Gas Cooled Fast Reactor with helium as coolant. GCFR included in the Generation-IV reactor systems are being developed to provide sustainable energy resources that meet future energy demand in a reliable, safe, and proliferation-resistant manner. This reactor can be operated without enrichment and reprocessing forever, once it starts. To obtain the capability of consuming natural uranium as fuel cycle input modified CANDLE burn-up scheme was adopted in this system with different core design. This study has compared the core with three designs of core reactors with the same thermal power 600 MWth. The fuel composition each design was arranged by divided core into several parts of equal volume axially i.e. 6, 8 and 10 parts related to material burn-up history. The fresh natural uranium is initially put in region 1, after one cycle of 10 years of burn-up it is shifted to region 2 and the region 1 is filled by fresh natural uranium fuel. This concept is basically applied to all regions, i.e. shifted the core of the region (i) into region (i+1) region after the end of 10 years burn-up cycle. The calculation results shows that for the burn-up strategy on “Region-8” and “Region-10” core designs, after the reactors start-up the operation furthermore they only needs natural uranium supply to the next life operation until one period of refueling (10 years).

  20. Operational Modal Analysis of Rotating Machinery

    DEFF Research Database (Denmark)

    Gres, Szymon; Andersen, Palle; Damkilde, Lars

    2019-01-01

    and deploys an orthogonal projection of the latter onto the raw measurements to remove the harmonic part of the signal. The new technique is a part of an semi-automated framework for OMA of structures contaminated with harmonics, whose flow is presented in this paper. The merit of the framework is discussed......Harmonic excitation of structures caused by rotating equipment is a problem faced by many engineers in the field of Operational Modal Analysis (OMA). Several methods to discard the influence of harmonic inputs over systems natural responses has been proposed in the literature and implemented...... in various software solutions. This paper recalls some of the most used techniques and uses a new time domain method for removing harmonics from measurements. Deployed method does not rely on filtering, statistical detection nor on non-linear fitting. Instead, it predicts the harmonic part of the time series...

  1. Operational Modal Analysis Tutorial

    DEFF Research Database (Denmark)

    Brincker, Rune; Andersen, Palle

    of modal parameters of practical interest - including the mode shape scaling factor - with a high degree of accuracy. It is also argued that the operational technology offers the user a number of advantages over traditional modal testing. The operational modal technology allows the user to perform a modal......In this paper the basic principles in operational modal testing and analysis are presented and discussed. A brief review of the techniques for operational modal testing and identification is presented, and it is argued, that there is now a wide range of techniques for effective identification...

  2. Multilayer modal actuator-based piezoelectric transformers.

    Science.gov (United States)

    Huang, Yao-Tien; Wu, Wen-Jong; Wang, Yen-Chieh; Lee, Chih-Kung

    2007-02-01

    An innovative, multilayer piezoelectric transformer equipped with a full modal filtering input electrode is reported herein. This modal-shaped electrode, based on the orthogonal property of structural vibration modes, is characterized by full modal filtering to ensure that only the desired vibration mode is excited during operation. The newly developed piezoelectric transformer is comprised of three layers: a multilayered input layer, an insulation layer, and a single output layer. The electrode shape of the input layer is derived from its structural vibration modal shape, which takes advantage of the orthogonal property of the vibration modes to achieve a full modal filtering effect. The insulation layer possesses two functions: first, to couple the mechanical vibration energy between the input and output, and second, to provide electrical insulation between the two layers. To meet the two functions, a low temperature, co-fired ceramic (LTCC) was used to provide the high mechanical rigidity and high electrical insulation. It can be shown that this newly developed piezoelectric transformer has the advantage of possessing a more efficient energy transfer and a wider optimal working frequency range when compared to traditional piezoelectric transformers. A multilayer piezoelectric, transformer-based inverter applicable for use in LCD monitors or portable displays is presented as well.

  3. Linear contextual modal type theory

    DEFF Research Database (Denmark)

    Schack-Nielsen, Anders; Schürmann, Carsten

    Abstract. When one implements a logical framework based on linear type theory, for example the Celf system [?], one is immediately con- fronted with questions about their equational theory and how to deal with logic variables. In this paper, we propose linear contextual modal type theory that gives...... a mathematical account of the nature of logic variables. Our type theory is conservative over intuitionistic contextual modal type theory proposed by Nanevski, Pfenning, and Pientka. Our main contributions include a mechanically checked proof of soundness and a working implementation....

  4. Vibration analysis of the piping system using the modal analysis method, 1

    International Nuclear Information System (INIS)

    Fujikawa, Takeshi; Kurohashi, Michiya; Inoue, Yoshio

    1975-01-01

    Modal analysis method was developed for the vibration analysis of piping system in nuclear or chemical plants, with finite element theory, and verified by sinusoidal vibration method. The natural vibration equation for pipings was derived with stiffness, attenuation and mass matrices, and eigenvalues are obtained with usual method, then the forced vibration equation for pipings was derived with the same manner, and the special solutions are given by modal method from the eigenvalues of the natural vibration equation. Three simple piping models (one, two and three dimensional) were made, and the natural vibration frequency was measured with forced input from an electrical dynamic shaker and a sound speaker. The experimental values of natural vibration frequency showed good agreement with the results by the analytical method. Therefore the theoretical approach for piping system vibration was proved to be valid. (Iwase, T.)

  5. Modal Logics and Definability

    OpenAIRE

    Kuusisto, Antti

    2013-01-01

    In recent years, research into the mathematical foundations of modal logic has become increasingly popular. One of the main reasons for this is the fact that modal logic seems to adapt well to the requirements of a wide range of different fields of application. This paper is a summary of some of the author’s contributions to the understanding of modal definability theory.

  6. The Modal Dimension

    Directory of Open Access Journals (Sweden)

    Giluano Torrengo

    2018-05-01

    Full Text Available Space and time are two obvious candidates as dimensions of reality. Yet, are they the only two dimensions of reality? Famously, David Lewis maintained the doctrine of ―modal realism‖, the thesis that possible worlds exist and are entities as concrete as the actual world that we live in. In this paper, I will explore the idea that modality can be construed as a dimension along with space and time. However, although Lewis‘ modal realism is the main source of inspiration for this construal of modality, I will argue that something else is required for having a modal dimension.

  7. Modal Identification of A Tested Steel Frame using Linear ARX Model Structure

    Directory of Open Access Journals (Sweden)

    Yavuz Kaya

    2009-07-01

    Full Text Available This study contains the identification of modal dynamic properties of a 3-story large-scale steel test frame structure through shaking table measurements. Shaking table test is carried out to estimate the modal properties of the test frame such as natural frequencies, damping ratios and mode shapes. Among many different model structures, ARX (Auto Recursive Exogenous model structure is used for modal identification of the frame structure system. The unknown parameters in the obtained ARX model structure are estimated by Least-Square method by minimizing the AIC criteria with the help of a program coded in advanced computing software MATLAB®. The adopted model structure is then tested out in time domain to verify the validity of the model with the selected model parameters. Then the modal characteristics of test frame and the story stiffness are estimated using the white noise shakings. An attempt is done to determine the change of modal characteristics and the story stiffness of test frame according to the velocity, which the test frame structure experienced during the shaking schedule and also during the input shaking of El Centro 1940 NS. Results shows that there is an increase in damping ratio and a decrease in both story stiffness and natural frequency for all modes when the damage forms at cementitious device and the test frame structure itself during the shaking schedule.

  8. Advances in Modal Logic

    DEFF Research Database (Denmark)

    Modal logic is a subject with ancient roots in the western logical tradition. Up until the last few generations, it was pursued mainly as a branch of philosophy. But in recent years, the subject has taken new directions with connections to topics in computer science and mathematics. This volume...... is the proceedings of the conference of record in its fi eld, Advances in Modal Logic. Its contributions are state-of-the-art papers. The topics include decidability and complexity results for specifi c modal logics, proof theory of modal logic, logics for reasoning about time and space, provability logic, dynamic...... epistemic logic, and the logic of evidence....

  9. Modal Identification from Ambient Responses using Frequency Domain Decomposition

    DEFF Research Database (Denmark)

    Brincker, Rune; Zhang, L.; Andersen, P.

    2000-01-01

    In this paper a new frequency domain technique is introduced for the modal identification from ambient responses, ie. in the case where the modal parameters must be estimated without knowing the input exciting the system. By its user friendliness the technique is closely related to the classical ...

  10. Modal Identification from Ambient Responses Using Frequency Domain Decomposition

    DEFF Research Database (Denmark)

    Brincker, Rune; Zhang, Lingmi; Andersen, Palle

    2000-01-01

    In this paper a new frequency domain technique is introduced for the modal identification from ambient responses, i.e. in the case where the modal parameters must be estimated without knowing the input exciting the system. By its user friendliness the technique is closely related to the classical...

  11. Modal logics are coalgebraic

    NARCIS (Netherlands)

    Cirstea, C.; Kurz, A.; Pattinson, D.; Schröder, L.; Venema, Y.

    2011-01-01

    Applications of modal logics are abundant in computer science, and a large number of structurally different modal logics have been successfully employed in a diverse spectrum of application contexts. Coalgebraic semantics, on the other hand, provides a uniform and encompassing view on the large

  12. The contribution to the modal analysis using an infrared camera

    Directory of Open Access Journals (Sweden)

    Dekys Vladimír

    2018-01-01

    Full Text Available The paper deals with modal analysis using an infrared camera. The test objects were excited by the modal exciter with narrowband noise and the response was registered as a frame sequence by the high speed infrared camera FLIR SC7500. The resonant frequencies and the modal shapes were determined from the infrared spectrum recordings. Lock-in technology has also been used. The experimental results were compared with calculated natural frequencies and modal shapes.

  13. Cross-modal versus within-modal recall: differences in behavioral and brain responses.

    Science.gov (United States)

    Butler, Andrew J; James, Karin H

    2011-10-31

    Although human experience is multisensory in nature, previous research has focused predominantly on memory for unisensory as opposed to multisensory information. In this work, we sought to investigate behavioral and neural differences between the cued recall of cross-modal audiovisual associations versus within-modal visual or auditory associations. Participants were presented with cue-target associations comprised of pairs of nonsense objects, pairs of nonsense sounds, objects paired with sounds, and sounds paired with objects. Subsequently, they were required to recall the modality of the target given the cue while behavioral accuracy, reaction time, and blood oxygenation level dependent (BOLD) activation were measured. Successful within-modal recall was associated with modality-specific reactivation in primary perceptual regions, and was more accurate than cross-modal retrieval. When auditory targets were correctly or incorrectly recalled using a cross-modal visual cue, there was re-activation in auditory association cortex, and recall of information from cross-modal associations activated the hippocampus to a greater degree than within-modal associations. Findings support theories that propose an overlap between regions active during perception and memory, and show that behavioral and neural differences exist between within- and cross-modal associations. Overall the current study highlights the importance of the role of multisensory information in memory. Copyright © 2011 Elsevier B.V. All rights reserved.

  14. Vocabulary acquisition in aphasia: Modality can matter.

    Science.gov (United States)

    Tuomiranta, Leena; Grönroos, Ann-Mari; Martin, Nadine; Laine, Matti

    2014-11-01

    The present case study investigated modality-specific aspects of novel word acquisition in aphasia. It was prompted by recent aphasia case studies indicating great interindividual variability in the ability to learn and maintain novel words in aphasia. Moreover, two previous case studies revealed a striking effect of input modality by showing effective word learning and re-learning via visual input only (Kohen, Sola, Tuomiranta, Laine, & Martin, 2012; Tuomiranta et al., 2014). The present participant TS with chronic nonfluent aphasia and post-semantic anomia was administered novel word-referent learning tasks. In the first experiment, the learning phase included simultaneous phonological and orthographic input, while the follow-up was probed separately for spoken and written responses. In the second experiment, we studied the effect of four different input and output modality combinations on her ability to learn to name the novel items. In the first experiment, TS's spoken naming performance during the learning phase was just within the range of healthy controls. Maintenance declined and remained outside that range during the whole 6-month follow-up. However, TS maintained the learned words better in written than in spoken naming throughout the follow-up, and in written naming, her maintenance stayed within the control's range up to 8 weeks post-training. The second experiment indicated that the best learning outcome was achieved with orthographic input. Orthographic input combined with orthographic output resulted in fast and accurate learning of the novel words. Interestingly, TS's test profile was opposite to her learning profile, as she repeated better than she read aloud in the linguistic background assessment. The results from the present case highlight the importance of multiple learning channels for word acquisition in individuals with aphasia. Probing the functionality of different input and output channels for learning may also prove valuable in tailoring

  15. A 500 year sediment lake record of anthropogenic and natural inputs to Windermere (English Lake District) using double-spike lead isotopes, radiochronology, and sediment microanalysis.

    Science.gov (United States)

    Miller, Helen; Croudace, Ian W; Bull, Jonathan M; Cotterill, Carol J; Dix, Justin K; Taylor, Rex N

    2014-07-01

    A high-resolution record of pollution is preserved in recent sediments from Windermere, the largest lake in the English Lake District. Data derived from X-ray core scanning (validated against wavelength dispersive X-ray fluorescence), radiochronological techniques ((210)Pb and (137)Cs) and ultrahigh precision, double-spike mass spectrometry for lead isotopes are combined to decipher the anthropogenic inputs to the lake. The sediment record suggests that while most element concentrations have been stable, there has been a significant increase in lead, zinc, and copper concentrations since the 1930s. Lead isotope down-core variations identify three major contributory sources of anthropogenic (industrial) lead, comprising gasoline lead, coal combustion lead (most likely source is coal-fired steam ships), and lead derived from Carboniferous Pb-Zn mineralization (mining activities). Periods of metal workings do not correlate with peaks in heavy metals due to the trapping efficiency of up-system lakes in the catchment. Heavy metal increases could be due to flood-induced metal inwash after the cessation of mining and the weathering of bedrock in the catchment. The combination of sediment analysis techniques used provides new insights into the pollutant depositional history of Windermere and could be similarly applied to other lake systems to determine the timing and scale of anthropogenic inputs.

  16. Rhesus monkeys see who they hear: spontaneous cross-modal memory for familiar conspecifics.

    Directory of Open Access Journals (Sweden)

    Ikuma Adachi

    Full Text Available Rhesus monkeys gather much of their knowledge of the social world through visual input and may preferentially represent this knowledge in the visual modality. Recognition of familiar faces is clearly advantageous, and the flexibility and utility of primate social memory would be greatly enhanced if visual memories could be accessed cross-modally either by visual or auditory stimulation. Such cross-modal access to visual memory would facilitate flexible retrieval of the knowledge necessary for adaptive social behavior. We tested whether rhesus monkeys have cross-modal access to visual memory for familiar conspecifics using a delayed matching-to-sample procedure. Monkeys learned visual matching of video clips of familiar individuals to photographs of those individuals, and generalized performance to novel videos. In crossmodal probe trials, coo-calls were played during the memory interval. The calls were either from the monkey just seen in the sample video clip or from a different familiar monkey. Even though the monkeys were trained exclusively in visual matching, the calls influenced choice by causing an increase in the proportion of errors to the picture of the monkey whose voice was heard on incongruent trials. This result demonstrates spontaneous cross-modal recognition. It also shows that viewing videos of familiar monkeys activates naturally formed memories of real monkeys, validating the use of video stimuli in studies of social cognition in monkeys.

  17. Normal modal preferential consequence

    CSIR Research Space (South Africa)

    Britz, K

    2012-12-01

    Full Text Available beyond the basic (propositional) KLM postulates, thereby making use of the additional expressivity provided by modal logic. In particular, we show that the additional constraints we impose on the preferential semantics ensure that the rule...

  18. Identification of anthropogenic and natural inputs of sulfate and chloride into the karstic ground water of Guiyang, SW China: combined delta37Cl and delta34S approach.

    Science.gov (United States)

    Liu, Cong-Qiang; Lang, Yun-Chao; Satake, Hiroshi; Wu, Jiahong; Li, Si-Liang

    2008-08-01

    Because of active exchange between surface and groundwater of a karstic hydrological system, the groundwater of Guiyang, the capital city of Guizhou Province, southwest China, has been seriously polluted by anthropogenic inputs of NO3-, SO4(2-), Cl-, and Na+. In this work, delta37Cl of chloride and delta34S variations of sulfate in the karstic surface/groundwater system were studied, with a main focus to identify contaminant sources, including their origins. The surface, ground, rain, and sewage water studied showed variable delta37Cl and delta34S values, in the range of -4.1 to +2.0 per thousand, and -20.4 to +20.9 per thousand for delta37Cl and delta34S (SO4(2-)), respectively. The rainwater samples yielded the lowest delta37Cl values among those observed to date for aerosols and rainwater. Chloride in the Guiyang area rain waters emanated from anthropogenic sources rather than being of marine origin, probably derived from HCl (g) emitted by coal combustion. By plotting 1/SO4(2-) vs delta34S and 1/Cl- vs delta37Cl, respectively, we were able to identify some clusters of data, which were assigned as atmospheric deposition (acid rain component), discharge from municipal sewage, paleo-brine components in clastic sedimentary rocks, dissolution of gypsum mainly in dolomite, oxidation of sulfide minerals in coal-containing clastic rocks, and possibly degradation of chlorine-containing organic matter. We conclude that human activities give a significant input of sulfate and chloride ions, as well as other contaminants, into the studied groundwater system through enhanced atmospheric deposition and municipal sewage, and that multiple isotopic tracers constitute a powerful tool to ascertain geochemical characteristics and origin of complex contaminants in groundwater.

  19. MRTouch: Adding Touch Input to Head-Mounted Mixed Reality.

    Science.gov (United States)

    Xiao, Robert; Schwarz, Julia; Throm, Nick; Wilson, Andrew D; Benko, Hrvoje

    2018-04-01

    We present MRTouch, a novel multitouch input solution for head-mounted mixed reality systems. Our system enables users to reach out and directly manipulate virtual interfaces affixed to surfaces in their environment, as though they were touchscreens. Touch input offers precise, tactile and comfortable user input, and naturally complements existing popular modalities, such as voice and hand gesture. Our research prototype combines both depth and infrared camera streams together with real-time detection and tracking of surface planes to enable robust finger-tracking even when both the hand and head are in motion. Our technique is implemented on a commercial Microsoft HoloLens without requiring any additional hardware nor any user or environmental calibration. Through our performance evaluation, we demonstrate high input accuracy with an average positional error of 5.4 mm and 95% button size of 16 mm, across 17 participants, 2 surface orientations and 4 surface materials. Finally, we demonstrate the potential of our technique to enable on-world touch interactions through 5 example applications.

  20. Material input of nuclear fuel

    International Nuclear Information System (INIS)

    Rissanen, S.; Tarjanne, R.

    2001-01-01

    The Material Input (MI) of nuclear fuel, expressed in terms of the total amount of natural material needed for manufacturing a product, is examined. The suitability of the MI method for assessing the environmental impacts of fuels is also discussed. Material input is expressed as a Material Input Coefficient (MIC), equalling to the total mass of natural material divided by the mass of the completed product. The material input coefficient is, however, only an intermediate result, which should not be used as such for the comparison of different fuels, because the energy contents of nuclear fuel is about 100 000-fold compared to the energy contents of fossil fuels. As a final result, the material input is expressed in proportion to the amount of generated electricity, which is called MIPS (Material Input Per Service unit). Material input is a simplified and commensurable indicator for the use of natural material, but because it does not take into account the harmfulness of materials or the way how the residual material is processed, it does not alone express the amount of environmental impacts. The examination of the mere amount does not differentiate between for example coal, natural gas or waste rock containing usually just sand. Natural gas is, however, substantially more harmful for the ecosystem than sand. Therefore, other methods should also be used to consider the environmental load of a product. The material input coefficient of nuclear fuel is calculated using data from different types of mines. The calculations are made among other things by using the data of an open pit mine (Key Lake, Canada), an underground mine (McArthur River, Canada) and a by-product mine (Olympic Dam, Australia). Furthermore, the coefficient is calculated for nuclear fuel corresponding to the nuclear fuel supply of Teollisuuden Voima (TVO) company in 2001. Because there is some uncertainty in the initial data, the inaccuracy of the final results can be even 20-50 per cent. The value

  1. Uncertainty in particle number modal analysis during transient operation of compressed natural gas, diesel, and trap-equipped diesel transit buses.

    Science.gov (United States)

    Holmén, Britt A; Qu, Yingge

    2004-04-15

    The relationships between transient vehicle operation and ultrafine particle emissions are not well-known, especially for low-emission alternative bus technologies such as compressed natural gas (CNG) and diesel buses equipped with particulate filters/traps (TRAP). In this study, real-time particle number concentrations measured on a nominal 5 s average basis using an electrical low pressure impactor (ELPI) for these two bus technologies are compared to that of a baseline catalyst-equipped diesel bus operated on ultralow sulfur fuel (BASE) using dynamometer testing. Particle emissions were consistently 2 orders of magnitude lower for the CNG and TRAP compared to BASE on all driving cycles. Time-resolved total particle numbers were examined in terms of sampling factors identified as affecting the ability of ELPI to quantify the particulate matter number emissions for low-emitting vehicles such as CNG and TRAP as a function of vehicle driving mode. Key factors were instrument sensitivity and dilution ratio, alignment of particle and vehicle operating data, sampling train background particles, and cycle-to-cycle variability due to vehicle, engine, after-treatment, or driver behavior. In-cycle variability on the central business district (CBD) cycle was highest for the TRAP configuration, but this could not be attributed to the ELPI sensitivity issues observed for TRAP-IDLE measurements. Elevated TRAP emissions coincided with low exhaust temperature, suggesting on-road real-world particulate filter performance can be evaluated by monitoring exhaust temperature. Nonunique particle emission maps indicate that measures other than vehicle speed and acceleration are necessary to model disaggregated real-time particle emissions. Further testing on a wide variety of test cycles is needed to evaluate the relative importance of the time history of vehicle operation and the hysteresis of the sampling train/dilution tunnel on ultrafine particle emissions. Future studies should

  2. Quantifying the value of investing in distributed natural gas and renewable electricity systems as complements: Applications of discounted cash flow and real options analysis with stochastic inputs

    International Nuclear Information System (INIS)

    Pless, Jacquelyn; Arent, Douglas J.; Logan, Jeffrey; Cochran, Jaquelin; Zinaman, Owen

    2016-01-01

    One energy policy objective in the United States is to promote the adoption of technologies that provide consumers with stable, secure, and clean energy. Recent work provides anecdotal evidence of natural gas (NG) and renewable electricity (RE) synergies in the power sector, however few studies quantify the value of investing in NG and RE systems together as complements. This paper uses discounted cash flow analysis and real options analysis to value hybrid NG-RE systems in distributed applications, focusing on residential and commercial projects assumed to be located in the states of New York and Texas. Technology performance and operational risk profiles are modeled at the hourly level to capture variable RE output and NG prices are modeled stochastically as geometric Ornstein-Uhlenbeck (OU) stochastic processes to capture NG price uncertainty. The findings consistently suggest that NG-RE hybrid distributed systems are more favorable investments in the applications studied relative to their single-technology alternatives when incentives for renewables are available. In some cases, NG-only systems are the favorable investments. Understanding the value of investing in NG-RE hybrid systems provides insights into one avenue towards reducing greenhouse gas emissions, given the important role of NG and RE in the power sector. - Highlights: • Natural gas and renewable electricity can be viewed as complements. • We model hybrid natural gas and renewable electricity systems at the hourly level. • We incorporate variable renewable power output and uncertain natural gas prices. • Hybrid natural gas and renewable electricity systems can be valuable investments.

  3. The modal study

    International Nuclear Information System (INIS)

    Cook, J.R.

    1988-01-01

    The term ''Modal Study'' refers to a research program conducted for the Nuclear Regulatory Commission (NRC) on the level of protection provided by NRC-certified packages during the shipment of spent nuclear fuel form U.S. power reactors. The objective of the study was to examine the response of the packages to actual highway and railway accident conditions. The Modal Study results show that NRC-certified spent fuel casks would perform their safety functions under severe, actual accident conditions. The study also explains how NRC's cask design conditions, which are expressed in engineering terms, relate to actual accident conditions, with which the public is more familiar. The Modal Study, along with other transportation studies, physical testing of casks, and the spent fuel shipment safety record confirm the view that casks provide a high level of public safety during spent fuel transport

  4. Input or intimacy

    Directory of Open Access Journals (Sweden)

    Judit Navracsics

    2014-01-01

    Full Text Available According to the critical period hypothesis, the earlier the acquisition of a second language starts, the better. Owing to the plasticity of the brain, up until a certain age a second language can be acquired successfully according to this view. Early second language learners are commonly said to have an advantage over later ones especially in phonetic/phonological acquisition. Native-like pronunciation is said to be most likely to be achieved by young learners. However, there is evidence of accentfree speech in second languages learnt after puberty as well. Occasionally, on the other hand, a nonnative accent may appear even in early second (or third language acquisition. Cross-linguistic influences are natural in multilingual development, and we would expect the dominant language to have an impact on the weaker one(s. The dominant language is usually the one that provides the largest amount of input for the child. But is it always the amount that counts? Perhaps sometimes other factors, such as emotions, ome into play? In this paper, data obtained from an EnglishPersian-Hungarian trilingual pair of siblings (under age 4 and 3 respectively is analyzed, with a special focus on cross-linguistic influences at the phonetic/phonological levels. It will be shown that beyond the amount of input there are more important factors that trigger interference in multilingual development.

  5. Parametric modal transition systems

    DEFF Research Database (Denmark)

    Beneš, Nikola; Křetínský, Jan; Larsen, Kim Guldstrand

    2011-01-01

    Modal transition systems (MTS) is a well-studied specification formalism of reactive systems supporting a step-wise refinement methodology. Despite its many advantages, the formalism as well as its currently known extensions are incapable of expressing some practically needed aspects in the refin......Modal transition systems (MTS) is a well-studied specification formalism of reactive systems supporting a step-wise refinement methodology. Despite its many advantages, the formalism as well as its currently known extensions are incapable of expressing some practically needed aspects...

  6. Access to Research Inputs

    DEFF Research Database (Denmark)

    Czarnitzki, Dirk; Grimpe, Christoph; Pellens, Maikel

    2015-01-01

    The viability of modern open science norms and practices depends on public disclosure of new knowledge, methods, and materials. However, increasing industry funding of research can restrict the dissemination of results and materials. We show, through a survey sample of 837 German scientists in life...... sciences, natural sciences, engineering, and social sciences, that scientists who receive industry funding are twice as likely to deny requests for research inputs as those who do not. Receiving external funding in general does not affect denying others access. Scientists who receive external funding...... of any kind are, however, 50 % more likely to be denied access to research materials by others, but this is not affected by being funded specifically by industry...

  7. Access to Research Inputs

    DEFF Research Database (Denmark)

    Czarnitzki, Dirk; Grimpe, Christoph; Pellens, Maikel

    The viability of modern open science norms and practices depend on public disclosure of new knowledge, methods, and materials. However, increasing industry funding of research can restrict the dissemination of results and materials. We show, through a survey sample of 837 German scientists in life...... sciences, natural sciences, engineering, and social sciences, that scientists who receive industry funding are twice as likely to deny requests for research inputs as those who do not. Receiving external funding in general does not affect denying others access. Scientists who receive external funding...... of any kind are, however, 50% more likely to be denied access to research materials by others, but this is not affected by being funded specifically by industry....

  8. Tense, aspect, and modality

    NARCIS (Netherlands)

    Pfau, R.; Steinbach, M.; Woll, B.; Pfau, R.; Steinbach, M.; Woll, B.

    2012-01-01

    Cross-linguistically, the grammatical categories tense, aspect, and modality - when they are overtly expressed - are generally realized by free morphemes (such as adverbials and auxiliaries) or by bound inflectional markers. The discussion in this chapter will make clear that this generalization

  9. A Modality Called 'Negation'

    NARCIS (Netherlands)

    Berto, F.

    2015-01-01

    I propose a comprehensive account of negation as a modal operator, vindicating a moderate logical pluralism. Negation is taken as a quantifier on worlds, restricted by an accessibility relation encoding the basic concept of compatibility. This latter captures the core meaning of the operator. While

  10. GIS-based approach for optimal siting and sizing of renewables considering techno-environmental constraints and the stochastic nature of meteorological inputs

    Science.gov (United States)

    Daskalou, Olympia; Karanastasi, Maria; Markonis, Yannis; Dimitriadis, Panayiotis; Koukouvinos, Antonis; Efstratiadis, Andreas; Koutsoyiannis, Demetris

    2016-04-01

    Following the legislative EU targets and taking advantage of its high renewable energy potential, Greece can obtain significant benefits from developing its water, solar and wind energy resources. In this context we present a GIS-based methodology for the optimal sizing and siting of solar and wind energy systems at the regional scale, which is tested in the Prefecture of Thessaly. First, we assess the wind and solar potential, taking into account the stochastic nature of the associated meteorological processes (i.e. wind speed and solar radiation, respectively), which is essential component for both planning (i.e., type selection and sizing of photovoltaic panels and wind turbines) and management purposes (i.e., real-time operation of the system). For the optimal siting, we assess the efficiency and economic performance of the energy system, also accounting for a number of constraints, associated with topographic limitations (e.g., terrain slope, proximity to road and electricity grid network, etc.), the environmental legislation and other land use constraints. Based on this analysis, we investigate favorable alternatives using technical, environmental as well as financial criteria. The final outcome is GIS maps that depict the available energy potential and the optimal layout for photovoltaic panels and wind turbines over the study area. We also consider a hypothetical scenario of future development of the study area, in which we assume the combined operation of the above renewables with major hydroelectric dams and pumped-storage facilities, thus providing a unique hybrid renewable system, extended at the regional scale.

  11. A refined Frequency Domain Decomposition tool for structural modal monitoring in earthquake engineering

    Science.gov (United States)

    Pioldi, Fabio; Rizzi, Egidio

    2017-07-01

    Output-only structural identification is developed by a refined Frequency Domain Decomposition ( rFDD) approach, towards assessing current modal properties of heavy-damped buildings (in terms of identification challenge), under strong ground motions. Structural responses from earthquake excitations are taken as input signals for the identification algorithm. A new dedicated computational procedure, based on coupled Chebyshev Type II bandpass filters, is outlined for the effective estimation of natural frequencies, mode shapes and modal damping ratios. The identification technique is also coupled with a Gabor Wavelet Transform, resulting in an effective and self-contained time-frequency analysis framework. Simulated response signals generated by shear-type frames (with variable structural features) are used as a necessary validation condition. In this context use is made of a complete set of seismic records taken from the FEMA P695 database, i.e. all 44 "Far-Field" (22 NS, 22 WE) earthquake signals. The modal estimates are statistically compared to their target values, proving the accuracy of the developed algorithm in providing prompt and accurate estimates of all current strong ground motion modal parameters. At this stage, such analysis tool may be employed for convenient application in the realm of Earthquake Engineering, towards potential Structural Health Monitoring and damage detection purposes.

  12. TART input manual

    International Nuclear Information System (INIS)

    Kimlinger, J.R.; Plechaty, E.F.

    1982-01-01

    The TART code is a Monte Carlo neutron/photon transport code that is only on the CRAY computer. All the input cards for the TART code are listed, and definitions for all input parameters are given. The execution and limitations of the code are described, and input for two sample problems are given

  13. Constructions, pragmatics and modality

    Directory of Open Access Journals (Sweden)

    Antonio Fortin

    2013-05-01

    Full Text Available This paper rejects the commonplace view that the semantics of certain modal deverbal adjectives (MDAs, which have traditionally been assumed to be non-compositional, require complex lexical or syntactic encoding (cf. e.g. Riehemann 1994 and 1998, Booij 2007 and 2010a. Instead, it shows that productive MDA formation is semantically compositional, and that the prima facie idiosyncratic meanings are, in fact, conversational implicatures.

  14. Does Modality Matter? The Effects of Reading, Listening, and Dual Modality on Comprehension

    Directory of Open Access Journals (Sweden)

    Beth A. Rogowsky

    2016-09-01

    Full Text Available With advancing technology, there is increasing interest in differences between listening versus reading comprehension or doing both simultaneously. Ninety-one participants were randomly assigned to one of three groups that received the same instructional material (the preface and a chapter from a non-fiction book, but each in a different input modality (digital audiobook, e-text, dual modality. After completing the material, participants took the same comprehension test in written form to establish both immediate comprehension (Time 1 and 2-week retention (Time 2. No statistically significant differences were found for any analyses pertaining to effects of the three different instructional conditions on comprehension at Time 1 or Time 2. Additional analyses showed that both males and females in each condition recalled an equal amount of information, regardless of whether they listened to an audiobook, read from an electronic tablet, or both listened and read simultaneously (dual modality.

  15. Modal Testing of Seven Shuttle Cargo Elements for Space Station

    Science.gov (United States)

    Kappus, Kathy O.; Driskill, Timothy C.; Parks, Russel A.; Patterson, Alan (Technical Monitor)

    2001-01-01

    From December 1996 to May 2001, the Modal and Control Dynamics Team at NASA's Marshall Space Flight Center (MSFC) conducted modal tests on seven large elements of the International Space Station. Each of these elements has been or will be launched as a Space Shuttle payload for transport to the International Space Station (ISS). Like other Shuttle payloads, modal testing of these elements was required for verification of the finite element models used in coupled loads analyses for launch and landing. The seven modal tests included three modules - Node, Laboratory, and Airlock, and four truss segments - P6, P3/P4, S1/P1, and P5. Each element was installed and tested in the Shuttle Payload Modal Test Bed at MSFC. This unique facility can accommodate any Shuttle cargo element for modal test qualification. Flexure assemblies were utilized at each Shuttle-to-payload interface to simulate a constrained boundary in the load carrying degrees of freedom. For each element, multiple-input, multiple-output burst random modal testing was the primary approach with controlled input sine sweeps for linearity assessments. The accelerometer channel counts ranged from 252 channels to 1251 channels. An overview of these tests, as well as some lessons learned, will be provided in this paper.

  16. Preferential reasoning for modal logics

    CSIR Research Space (South Africa)

    Britz, K

    2011-11-01

    Full Text Available Modal logic is the foundation for a versatile and well-established class of knowledge representation formalisms in artificial intelligence. Enriching modal logics with non-monotonic reasoning capabilities such as preferential reasoning as developed...

  17. On the use of Kripke modality in language theory

    DEFF Research Database (Denmark)

    Nielsen, Karsten Hvidtfelt

    2006-01-01

    The article shows how the formal modal technique known as 'Kripke-Modality' can be used as a descriptive tool in language theory. My use is motivated by a version of the well-known liar's paradox: anyone claiming natural language to be semantically undecidable may only on pain on inconsistency...

  18. Applied modal analysis of wind turbine blades

    DEFF Research Database (Denmark)

    Pedersen, H.B.; Kristensen, O.J.D.

    2003-01-01

    In this project modal analysis has been used to determine the natural frequencies, damping and the mode shapes for wind turbine blades. Different methods to measure the position and adjust the direction of the measuring points are discussed. Differentequipment for mounting the accelerometers...... is investigated by repeated measurement on the same wind turbine blade. Furthermore the flexibility of the test set-up is investigated, by use ofaccelerometers mounted on the flexible adapter plate during the measurement campaign. One experimental campaign investigated the results obtained from a loaded...... and unloaded wind turbine blade. During this campaign the modal analysis are performed on ablade mounted in a horizontal and a vertical position respectively. Finally the results obtained from modal analysis carried out on a wind turbine blade are compared with results obtained from the Stig Øyes blade_EV1...

  19. Input-output supervisor

    International Nuclear Information System (INIS)

    Dupuy, R.

    1970-01-01

    The input-output supervisor is the program which monitors the flow of informations between core storage and peripheral equipments of a computer. This work is composed of three parts: 1 - Study of a generalized input-output supervisor. With sample modifications it looks like most of input-output supervisors which are running now on computers. 2 - Application of this theory on a magnetic drum. 3 - Hardware requirement for time-sharing. (author) [fr

  20. Advances of operational modal identification

    International Nuclear Information System (INIS)

    Zhang, L.

    2001-01-01

    Operational modal analysis has shown many advantages compared to the traditional one. In this paper, the development of ambient modal identification in time domain is summarized. The mathematical models for modal identification have been presented as unified framework for time domain (TD) System realization algorithms, such as polyrefence (PRCE), extended Ibrahim time domain (EITD) and eigensystem realization algorithm (ERA), etc., and recently developed Stochastic subspace technique (SST). The latest technique named as frequency domain decomposition (FDD) is introduced for operational modal identification, which has many advantages as a frequency domain (FD) technique. Applications of the operational modal analysis in civil and mechanical engineering have shown the success and accuracy of the advanced operational modal identification algorithms- FDD and SST techniques. The major issues of TD and FD operational modal identification are also discussed. (author)

  1. On modal cross-coupling in the asymptotic modal limit

    Science.gov (United States)

    Culver, Dean; Dowell, Earl

    2018-03-01

    The conditions under which significant modal cross-coupling occurs in dynamical systems responding to high-frequency, broadband forcing that excites many modes is studied. The modal overlap factor plays a key role in the analysis of these systems as the modal density (the ratio of number of modes to the frequency bandwidth) becomes large. The modal overlap factor is effectively the ratio of the width of a resonant peak (the damping ratio times the resonant frequency) to the average frequency interval between resonant peaks (or rather, the inverse of the modal density). It is shown that this parameter largely determines whether substantial modal cross-coupling occurs in a given system's response. Here, two prototypical systems are considered. The first is a simple rectangular plate whose significant modal cross-coupling is the exception rather than the norm. The second is a pair of rectangular plates attached at a point where significant modal cross-coupling is more likely to occur. We show that, for certain cases of modal density and damping, non-negligible cross coupling occurs in both systems. Under similar circumstances, the constraint force between the two plates in the latter system becomes broadband. The implications of this for using Asymptotic Modal Analysis (AMA) in multi-component systems are discussed.

  2. SSYST-3. Input description

    International Nuclear Information System (INIS)

    Meyder, R.

    1983-12-01

    The code system SSYST-3 is designed to analyse the thermal and mechanical behaviour of a fuel rod during a LOCA. The report contains a complete input-list for all modules and several tested inputs for a LOCA analysis. (orig.)

  3. MDS MIC Catalog Inputs

    Science.gov (United States)

    Johnson-Throop, Kathy A.; Vowell, C. W.; Smith, Byron; Darcy, Jeannette

    2006-01-01

    This viewgraph presentation reviews the inputs to the MDS Medical Information Communique (MIC) catalog. The purpose of the group is to provide input for updating the MDS MIC Catalog and to request that MMOP assign Action Item to other working groups and FSs to support the MITWG Process for developing MIC-DDs.

  4. Word Spelling Assessment Using ICT: The Effect of Presentation Modality

    Science.gov (United States)

    Sarris, Menelaos; Panagiotakopoulos, Chris

    2010-01-01

    Up-to-date spelling process was assessed using typical spelling-to-dictation tasks, where children's performance was evaluated mainly in terms of spelling error scores. In the present work a simple graphical computer interface is reported, aiming to investigate the effects of input modality (e.g. visual and verbal) in word spelling. The software…

  5. Operational Modal Analysis of the Cablestayed Footbridge

    Directory of Open Access Journals (Sweden)

    Kortiš Ján

    2017-12-01

    Full Text Available Modern architecture leads to design subtle bridge structures that are more sensitive to increased dynamic loading than the massive ones. This phenomenon can be especially observed on lightweight steel structures such as suspended footbridges. As a result, it is necessary to know precisely its dynamic characteristics, such as natural frequencies, natural shapes and damping of construction. This information can be used for further analysis such as damage detection, system identification, health monitoring, etc. or also for the design of new types of construction. For this purpose, classical modal analysis using trigger load or harmonic vibration exciter in combination with acceleration sensors is used in practice. However, there are many situations where it is not possible to stop the traffic or operation of the bridge. The article presents an experimental measurement of the dynamic parameters of the structure at the operating load using the operational modal analysis.

  6. Operational Modal Analysis of the Cablestayed Footbridge

    Science.gov (United States)

    Kortiš, Ján; Daniel, Ľuboš; Farbák, Matúš; Maliar, Lukáš; Škarupa, Milan

    2017-12-01

    Modern architecture leads to design subtle bridge structures that are more sensitive to increased dynamic loading than the massive ones. This phenomenon can be especially observed on lightweight steel structures such as suspended footbridges. As a result, it is necessary to know precisely its dynamic characteristics, such as natural frequencies, natural shapes and damping of construction. This information can be used for further analysis such as damage detection, system identification, health monitoring, etc. or also for the design of new types of construction. For this purpose, classical modal analysis using trigger load or harmonic vibration exciter in combination with acceleration sensors is used in practice. However, there are many situations where it is not possible to stop the traffic or operation of the bridge. The article presents an experimental measurement of the dynamic parameters of the structure at the operating load using the operational modal analysis.

  7. PLEXOS Input Data Generator

    Energy Technology Data Exchange (ETDEWEB)

    2017-02-01

    The PLEXOS Input Data Generator (PIDG) is a tool that enables PLEXOS users to better version their data, automate data processing, collaborate in developing inputs, and transfer data between different production cost modeling and other power systems analysis software. PIDG can process data that is in a generalized format from multiple input sources, including CSV files, PostgreSQL databases, and PSS/E .raw files and write it to an Excel file that can be imported into PLEXOS with only limited manual intervention.

  8. ColloInputGenerator

    DEFF Research Database (Denmark)

    2013-01-01

    This is a very simple program to help you put together input files for use in Gries' (2007) R-based collostruction analysis program. It basically puts together a text file with a frequency list of lexemes in the construction and inserts a column where you can add the corpus frequencies. It requires...... it as input for basic collexeme collostructional analysis (Stefanowitsch & Gries 2003) in Gries' (2007) program. ColloInputGenerator is, in its current state, based on programming commands introduced in Gries (2009). Projected updates: Generation of complete work-ready frequency lists....

  9. Input description for BIOPATH

    International Nuclear Information System (INIS)

    Marklund, J.E.; Bergstroem, U.; Edlund, O.

    1980-01-01

    The computer program BIOPATH describes the flow of radioactivity within a given ecosystem after a postulated release of radioactive material and the resulting dose for specified population groups. The present report accounts for the input data necessary to run BIOPATH. The report also contains descriptions of possible control cards and an input example as well as a short summary of the basic theory.(author)

  10. Input and execution

    International Nuclear Information System (INIS)

    Carr, S.; Lane, G.; Rowling, G.

    1986-11-01

    This document describes the input procedures, input data files and operating instructions for the SYVAC A/C 1.03 computer program. SYVAC A/C 1.03 simulates the groundwater mediated movement of radionuclides from underground facilities for the disposal of low and intermediate level wastes to the accessible environment, and provides an estimate of the subsequent radiological risk to man. (author)

  11. Gestures and multimodal input

    OpenAIRE

    Keates, Simeon; Robinson, Peter

    1999-01-01

    For users with motion impairments, the standard keyboard and mouse arrangement for computer access often presents problems. Other approaches have to be adopted to overcome this. In this paper, we will describe the development of a prototype multimodal input system based on two gestural input channels. Results from extensive user trials of this system are presented. These trials showed that the physical and cognitive loads on the user can quickly become excessive and detrimental to the interac...

  12. natural

    Directory of Open Access Journals (Sweden)

    Elías Gómez Macías

    2006-01-01

    Full Text Available Partiendo de óxido de magnesio comercial se preparó una suspensión acuosa, la cual se secó y calcinó para conferirle estabilidad térmica. El material, tanto fresco como usado, se caracterizó mediante DRX, área superficial BET y SEM-EPMA. El catalizador mostró una matriz de MgO tipo periclasa con CaO en la superficie. Las pruebas de actividad catalítica se efectuaron en lecho fijo empacado con partículas obtenidas mediante prensado, trituración y clasificación del material. El flujo de reactivos consistió en mezclas gas natural-aire por debajo del límite inferior de inflamabilidad. Para diferentes flujos y temperaturas de entrada de la mezcla reactiva, se midieron las concentraciones de CH4, CO2 y CO en los gases de combustión con un analizador de gases tipo infrarrojo no dispersivo (NDIR. Para alcanzar conversión total de metano se requirió aumentar la temperatura de entrada al lecho a medida que se incrementó el flujo de gases reaccionantes. Los resultados obtenidos permiten desarrollar un sistema de combustión catalítica de bajo costo con un material térmicamente estable, que promueva la alta eficiencia en la combustión de gas natural y elimine los problemas de estabilidad, seguridad y de impacto ambiental negativo inherentes a los procesos de combustión térmica convencional.

  13. Metaphysical Modality, Modality of Predicate and the Theory of

    Directory of Open Access Journals (Sweden)

    l nabavi

    2010-05-01

    This paper discusses the historical overview of the metaphysical modality firstly and then shows that the theory of "Decisive Necessity” is true and justified in a model of modal logic with equivalent accessibility relation and homogeneous possible world view (fixed domain.

  14. Identification and integration of sensory modalities: Neural basis and relation to consciousness

    NARCIS (Netherlands)

    Pennartz, C.M.A.

    2009-01-01

    A key question in studying consciousness is how neural operations in the brain can identify streams of sensory input as belonging to distinct modalities, which contributes to the representation of qualitatively different experiences. The basis for identification of modalities is proposed to be

  15. Applying Cognitive Linguistics to Instructed L2 Learning: The English Modals

    Science.gov (United States)

    Tyler, Andrea; Mueller, Charles M.; Ho, Vu

    2010-01-01

    This paper reports the results of a quasi-experimental effects-of-instruction study examining the efficacy of applying a Cognitive Linguistic (CL) approach to L2 learning of the semantics of English modals. In spite of their frequency in typical input, modal verbs present L2 learners with difficulties, party due to their inherent…

  16. Modal Identification of Output-Only Systems using Frequency Domain Decomposition

    DEFF Research Database (Denmark)

    Brincker, Rune; Zhang, L.; Andersen, P.

    2000-01-01

    In this paper a new frequency domain technique is introduced for the modal identification from ambient responses, ie. in the case where the modal parameters must be estimated without knowing the input exciting the system. By its user friendliness the technique is closely related to the classical ...

  17. On Modal Refinement and Consistency

    DEFF Research Database (Denmark)

    Nyman, Ulrik; Larsen, Kim Guldstrand; Wasowski, Andrzej

    2007-01-01

    Almost 20 years after the original conception, we revisit several fundamental question about modal transition systems. First, we demonstrate the incompleteness of the standard modal refinement using a counterexample due to Hüttel. Deciding any refinement, complete with respect to the standard...

  18. Krull dimension in modal logic

    NARCIS (Netherlands)

    Bezhanishvili, G.; Bezhanishvili, N.; Lucero-Bryan, J.; van Mill, J.

    2017-01-01

    We develop the theory of Krull dimension for S4-algebras and Heyting algebras. This leads to the concept of modal Krull dimension for topological spaces. We compare modal Krull dimension to other well-known dimension functions, and show that it can detect differences between topological spaces that

  19. Modal Logics for Cryptographic Processes

    DEFF Research Database (Denmark)

    Frendrup, U.; Huttel, Hans; Jensen, N. J.

    2002-01-01

    We present three modal logics for the spi-calculus and show that they capture strong versions of the environment sensitive bisimulation introduced by Boreale et al. Our logics differ from conventional modal logics for process calculi in that they allow us to describe the knowledge of an attacker ...

  20. Evidentiality, Epistemic Modality, and Epistemic Status

    Directory of Open Access Journals (Sweden)

    Rezeda Dilshatovna Shakirova

    2016-09-01

    Full Text Available The article discusses the interaction of evidentiality categories, typical of many Turkic, Finno-Ugric, Samoyed, certain Slavic, and other languages with the categories of epistemic modality, which is widely represented particularly in Germanic languages. The methodological framework of this study consists of the general philosophic, general scientific and private levels. The general philosophic methodology is based on the analytic philosophy, under the linguistic trend of which the language study was carried out to solve philosophic problems. The general scientific methodological bases of the study are related to the principle of identifying similarities and differences of the categories analyzed and the systematicity of description, whereas the descriptive method and techniques thereof are used primarily as the private-linguistic methods. In contrast to evidentiality, indicating the source of information, the epistemic modality marks different level of the information reliability. In the modern German language, the categories studied have a zone of intersection in terms of community within the means of expression, to which modal words and modal verbs as well as the verb scheinen can be primarily related. However, in the modern German language, there is no question of the category of evidentiality in the plane, within which it is currently being studied basing on the material of those languages, to the fragment of the grammatical system of which it is primarily inherent. As a rule, the semantics of evidentiality in these languages provides no information on the degree of reliability of the source of knowledge. To overcome the contradiction of such nature, this work suggests paying attention to the category of epistemic status of an utterance, the semantic structure of which is wider than evidentiality and epistemic modality and includes the level of reliability of the source of knowledge along with the designation thereof. In today's German

  1. Fast modal decomposition for optical fibers using digital holography.

    Science.gov (United States)

    Lyu, Meng; Lin, Zhiquan; Li, Guowei; Situ, Guohai

    2017-07-26

    Eigenmode decomposition of the light field at the output end of optical fibers can provide fundamental insights into the nature of electromagnetic-wave propagation through the fibers. Here we present a fast and complete modal decomposition technique for step-index optical fibers. The proposed technique employs digital holography to measure the light field at the output end of the multimode optical fiber, and utilizes the modal orthonormal property of the basis modes to calculate the modal coefficients of each mode. Optical experiments were carried out to demonstrate the proposed decomposition technique, showing that this approach is fast, accurate and cost-effective.

  2. Dual modality densitometry

    International Nuclear Information System (INIS)

    Tjugum, Stein-Arild

    2003-01-01

    Different measurement principles and design issues for gamma-ray densitometry for pipe flow are investigated. The dual modality densitometry (DMD) principle for salinity measurement and flow regime identification by multibeam densitometry are tested and verified. The measurement principles are implemented in a compact instrument design with low energy source and compact detectors. The DMD principle is experimentally verified for 3 inch and 2 inch pipes. These measurements are done on homogenous brine/gas mixtures. Both salinity independent GVF measurements and salinity measurements are obtained. The standard deviation of the salinity measurements are about 2 percent. This measurement inaccuracy is mainly caused by inhomogeneity in the liquid/gas distribution, and measurements are thus sensitive to changes in the flow regime. Models for the generation of scattered radiation are developed, and these have been used in the data-analysis and for producing special sensitivity maps for the generation of scattered radiation. The models are a useful tool for further development of the DMD principle. The work on multibeam gamma-ray densitometry has shown that flow regimes can be identified with as few as two detectors. This is verified in the flow-loop tests. Unambiguous flow regime identification will often require that the multibeam measurements are combined with other flow measurements. With a higher number of detectors more detailed information is found, and from the 9-beam measurements with the University of Bergen (UoB) gamma-ray tomography different flow regimes could clearly be identified from time series plots of the data. A laboratory prototype compact gamma-ray densitometer, the MiniGamma, has been built up and tested. Both the DMD measurement principle and the multibeam arrangement for flow regime identification are implemented in the instrument, and are successfully tested. The detector-types tested are CdZnTe semiconductor detectors, a miniature scintillation

  3. A Causal Theory of Modality

    Directory of Open Access Journals (Sweden)

    José Tomás Alvarado

    2009-08-01

    Full Text Available This work presents a causal conception of metaphysical modality in which a state of affairs is metaphysically possible if and only if it can be caused (in the past, the present or the future by current entities. The conception is contrasted with what is called the “combinatorial” conception of modality, in which everything can co-exist with anything else. This work explains how the notion of ‘causality’ should be construed in the causal theory, what difference exists between modalities thus defined from nomological modality, how accessibility relations between possible worlds should be interpreted, and what is the relation between the causal conception and the necessity of origin.

  4. Kajian Eksperimental Parameter Modal Bangunan Dua Lantai dengan Metode Modal Analisis

    Directory of Open Access Journals (Sweden)

    Islahuddin Islahuddin

    2016-12-01

    transformedin a FRF graph. FRF will then be processed in order to get structure mode shape. From the shape mode, analysis of themachine damage by looking at save amplitude value may be done. The purpose of this research is analyzing thedynamic character of vibration behavior on the structure model of two floor building. The testing is carried out byimplementing excitation force by using impact hammer. Accelerometer is used to measure structure vibrate signal. Theposition of accelerometer is variety for every eight different testing area. Meanwhile, the position of excitation force isthe same for all area of testing. This research applied experimental analysis modal method in order to identify dynamiccharacteristic of the structure model of two floor building. The aims of analysis modal technique are getting the modalparameter such as frequency, damping ratio, and mode shapes. The result of this research is the first natural frequencyon the maximum amplitude is the same of 2,313 Hz. While, for the second natural frequency on the maximum amplitudeis different on area 3 and area 7. This happened as the effect of the differences of excitation force in the testing area.Keywords: Dynamic characteristic, experimental modal analysis, natural frequency, FRF

  5. Cross-modal perceptual load: the impact of modality and individual differences.

    Science.gov (United States)

    Sandhu, Rajwant; Dyson, Benjamin James

    2016-05-01

    Visual distractor processing tends to be more pronounced when the perceptual load (PL) of a task is low compared to when it is high [perpetual load theory (PLT); Lavie in J Exp Psychol Hum Percept Perform 21(3):451-468, 1995]. While PLT is well established in the visual domain, application to cross-modal processing has produced mixed results, and the current study was designed in an attempt to improve previous methodologies. First, we assessed PLT using response competition, a typical metric from the uni-modal domain. Second, we looked at the impact of auditory load on visual distractors, and of visual load on auditory distractors, within the same individual. Third, we compared individual uni- and cross-modal selective attention abilities, by correlating performance with the visual Attentional Network Test (ANT). Fourth, we obtained a measure of the relative processing efficiency between vision and audition, to investigate whether processing ease influences the extent of distractor processing. Although distractor processing was evident during both attend auditory and attend visual conditions, we found that PL did not modulate processing of either visual or auditory distractors. We also found support for a correlation between the uni-modal (visual) ANT and our cross-modal task but only when the distractors were visual. Finally, although auditory processing was more impacted by visual distractors, our measure of processing efficiency only accounted for this asymmetry in the auditory high-load condition. The results are discussed with respect to the continued debate regarding the shared or separate nature of processing resources across modalities.

  6. Distinctiveness and Bidirectional Effects in Input Enhancement for Vocabulary Learning

    Science.gov (United States)

    Barcroft, Joe

    2003-01-01

    This study examined input enhancement and second language (L2) vocabulary learning while exploring the role of "distinctiveness," the degree to which an item in the input diverges from the form in which other items in the input are presented, with regard to the nature and direction of the effects of enhancement. In this study,…

  7. A Modal Description of Multiport Antennas

    Directory of Open Access Journals (Sweden)

    Jonathan J. Lynch

    2011-01-01

    Full Text Available This paper presents a modal description of multiport antennas that leads directly to a rigorous network representation and simple quadratic expressions for gain, efficiency, and effective area. The analysis shows that the transmitting and receiving properties of an element antenna array are exactly described by a 2×2 element scattering matrix together with a set of orthonormal mode functions and accounts for effects such as mutual coupling, scattering, reflection, and losses. The approach is quite general, only requiring that the antenna be finite and reciprocal. The scattering network description simplifies accounting of power flow while retaining a close connection to the physical antenna characteristics. The orthonormal mode functions provide a complete basis for radiated and received fields, facilitating beamforming. The theory provides rigorous definitions of input-output signals and links them to the underlying electromagnetics in a straightforward manner.

  8. Applied modal analysis of wind turbine blades

    Energy Technology Data Exchange (ETDEWEB)

    Broen Pedersen, H.; Dahl Kristensen, O.J.

    2003-02-01

    In this project modal analysis has been used to determine the natural frequencies, damping and the mode shapes for wind turbine blades. Different methods to measure the position and adjust the direction of the measuring points are discussed. Different equipment for mounting the accelerometers are investigated and the most suitable are chosen. Different excitation techniques are tried during experimental campaigns. After a discussion the pendulum hammer were chosen, and a new improved hammer was manufactured. Some measurement errors are investigated. The ability to repeat the measured results is investigated by repeated measurement on the same wind turbine blade. Furthermore the flexibility of the test set-up is investigated, by use of accelerometers mounted on the flexible adapter plate during the measurement campaign. One experimental campaign investigated the results obtained from a loaded and unloaded wind turbine blade. During this campaign the modal analysis are performed on a blade mounted in a horizontal and a vertical position respectively. Finally the results obtained from modal analysis carried out on a wind turbine blade are compared with results obtained from the Stig Oeyes blade{sub E}V1 program. (au)

  9. Identification of anthropogenic and natural inputs of sulfate into a karstic coastal groundwater system in northeast China: evidence from major ions, δ13CDIC and δ34SSO4

    Science.gov (United States)

    Han, Dongmei; Song, Xianfang; Currell, Matthew J.

    2016-05-01

    The hydrogeochemical processes controlling groundwater evolution in the Daweijia area of Dalian, northeast China, were characterised using hydrochemistry and isotopes of carbon and sulfur (δ13CDIC and δ34SSO4). The aim was to distinguish anthropogenic impacts as distinct from natural processes, with a particular focus on sulfate, which is found at elevated levels (range: 54.4 to 368.8 mg L-1; mean: 174.4 mg L-1) in fresh and brackish groundwater. The current investigation reveals minor seawater intrusion impact (not exceeding 5 % of the overall solute load), in contrast with extensive impacts observed in 1982 during the height of intensive abstraction. This indicates that measures to restrict groundwater abstraction have been effective. However, hydrochemical facies analysis shows that the groundwater remains in a state of ongoing hydrochemical evolution (towards Ca-Cl type water) and quality degradation (increasing nitrate and sulfate concentrations). The wide range of NO3 concentrations (74.7-579 mg L-1) in the Quaternary aquifer indicates considerable input of fertilisers and/or leakage from septic systems. Both δ13C (-14.5 to -5.9 permil) and δ34SSO4 (+5.4 to +13.1 permil) values in groundwater show increasing trends along groundwater flow paths. While carbonate minerals may contribute to increasing δ13CDIC and δ34SSO4 values in deep karstic groundwater, high loads of agricultural fertilisers reaching the aquifer via irrigation return flow are likely the main source of the dissolved sulfate in Quaternary groundwater, as shown by distinctive isotopic ratios and a lack of evidence for other sources in the major ion chemistry. According to isotope mass balance calculations, the fertiliser contribution to overall sulfate has reached an average of 62.1 % in the Quaternary aquifer, which has a strong hydraulic connection to the underlying carbonate aquifer. The results point to an alarming level of impact from the local intensive agriculture on the groundwater

  10. CM-2 Environmental/Modal Testing of SPACEHAB Racks

    Science.gov (United States)

    McNelis, Mark E.; Goodnight, Thomas W.

    2001-01-01

    Combined environmental/modal vibration testing has been implemented at the NASA Glenn Research Center's Structural Dynamics Laboratory. The benefits of combined vibration testing are that it facilitates test article modal characterization and vibration qualification testing. The Combustion Module-2 (CM-2) is a space experiment that will launch on shuttle mission STS-107 in the SPACEHAB Research Double Module. The CM-2 flight hardware is integrated into a SPACEHAB single and double rack. CM-2 rack-level combined vibration testing was recently completed on a shaker table to characterize the structure's modal response and verify the random vibration response. Control accelerometers and limit force gauges, located between the fixture and rack interface, were used to verify the input excitation. Results of the testing were used to verify the loads and environments for flight on the shuttles.

  11. HDR flood-water storage-tank modal vibration tests

    International Nuclear Information System (INIS)

    Gorman, V.W.; Thinnes, G.L.

    1983-01-01

    Modal vibration tests were conducted by EG and G Idaho on two vessels located at West Germany's Heissdampfreaktor (HDR) facility which is 25 kilometers east of Frankfurt. The tests were performed during May and June 1982 for the US Nuclear Regulatory Commission (NRC) as part of their cooperative effort with Kernforschungszentrum Karlsruhe (KfK) of West Germany. The primary purpose for performing this task was to determine modal properties (frequencies, mode shapes and associated damping ratios) in order to eventually provide guidelines for standards development by the NRC in modeling similar vessels. One of the vessels tested was a flood water storage tank (FWST) for empty, half full and full water conditions. The FWST was excited randomly with an electromagnetic shaker and by impulsive hammer blows. Excitation or input forces together with measured vessel responses were processed by a digital modal analyzer and stored on magnetic disks for subsequent evaluation

  12. Modal analysis of wind turbine blades

    Energy Technology Data Exchange (ETDEWEB)

    Larsen, G.C.; Hansen, M.H.; Baumgart, A.; Carlen, I.

    2002-02-01

    The modal analysis technique has been used to identify essential dynamic properties of wind turbine blades like natural frequencies, damping characteristics and mode shapes. Different experimental procedures have been considered, and the most appropriate of these has been selected. Although the comparison is based on measurements on a LM 19 m blade, the recommendations given are believed to be valid for other wind turbine blades as well. The reliability of the selected experimental analysis has been quantified by estimating the unsystematic variations in the experimental findings. Satisfactory results have been obtained for natural frequencies, damping characteristics and for the dominating deflection direction of the investigated mode shapes. For the secondary deflection directions, the observed experimental uncertainty may be considerable - especially for the torsional deflection. The experimental analysis of the LM 19 m blade has been compared with results from a state-of-the-art FE-modeling of the same blade. For some of the higher modes substantial discrepancies between the natural frequencies originating from the FE-modeling and the modal analysis, respectively, are observed. In general the qualitative features of measured and computed modes shapes are in good agreement. However, for the secondary deflection directions, substantial deviations in the absolute values may occur (when normalizing with respect to the primary deflection direction). Finally, suggestions of potential future improvements of the experimental procedure are discussed. (au)

  13. Radioactive inputs to the North Sea and the Channel

    International Nuclear Information System (INIS)

    1984-01-01

    The subject is covered in sections: introduction (radioactivity; radioisotopes; discharges from nuclear establishments); data sources (statutory requirements); sources of liquid radioactive waste (figure showing location of principal sources of radioactive discharges; tables listing principal discharges by activity and by nature of radioisotope); Central Electricity Generating Board nuclear power stations; research and industrial establishments; Ministy of Defence establishments; other UK inputs of radioactive waste; total inputs to the North Sea and the Channel (direct inputs; river inputs; adjacent sea areas); conclusions. (U.K.)

  14. Preemptive analgesia I: physiological pathways and pharmacological modalities.

    LENUS (Irish Health Repository)

    Kelly, D J

    2012-02-03

    PURPOSE: This two-part review summarizes the current knowledge of physiological mechanisms, pharmacological modalities and controversial issues surrounding preemptive analgesia. SOURCE: Articles from 1966 to present were obtained from the MEDLINE databases. Search terms included: analgesia, preemptive; neurotransmitters; pain, postoperative; hyperalgesia; sensitization, central nervous system; pathways, nociception; anesthetic techniques; analgesics, agents. Principal findings: The physiological basis of preemptive analgesia is complex and involves modification of the pain pathways. The pharmacological modalities available may modify the physiological responses at various levels. Effective preemptive analgesic techniques require multi-modal interception of nociceptive input, increasing threshold for nociception, and blocking or decreasing nociceptor receptor activation. Although the literature is controversial regarding the effectiveness of preemptive analgesia, some general recommendations can be helpful in guiding clinical care. Regional anesthesia induced prior to surgical trauma and continued well into the postoperative period is effective in attenuating peripheral and central sensitization. Pharmacologic agents such as NSAIDs (non-steroidal anti-inflammatory drugs) opioids, and NMDA (N-methyl-D-aspartate) - and alpha-2-receptor antagonists, especially when used in combination, act synergistically to decrease postoperative pain. CONCLUSION: The variable patient characteristics and timing of preemptive analgesia in relation to surgical noxious input requires individualization of the technique(s) chosen. Multi-modal analgesic techniques appear most effective.

  15. FLUTAN input specifications

    International Nuclear Information System (INIS)

    Borgwaldt, H.; Baumann, W.; Willerding, G.

    1991-05-01

    FLUTAN is a highly vectorized computer code for 3-D fluiddynamic and thermal-hydraulic analyses in cartesian and cylinder coordinates. It is related to the family of COMMIX codes originally developed at Argonne National Laboratory, USA. To a large extent, FLUTAN relies on basic concepts and structures imported from COMMIX-1B and COMMIX-2 which were made available to KfK in the frame of cooperation contracts in the fast reactor safety field. While on the one hand not all features of the original COMMIX versions have been implemented in FLUTAN, the code on the other hand includes some essential innovative options like CRESOR solution algorithm, general 3-dimensional rebalacing scheme for solving the pressure equation, and LECUSSO-QUICK-FRAM techniques suitable for reducing 'numerical diffusion' in both the enthalphy and momentum equations. This report provides users with detailed input instructions, presents formulations of the various model options, and explains by means of comprehensive sample input, how to use the code. (orig.) [de

  16. GARFEM input deck description

    Energy Technology Data Exchange (ETDEWEB)

    Zdunek, A.; Soederberg, M. (Aeronautical Research Inst. of Sweden, Bromma (Sweden))

    1989-01-01

    The input card deck for the finite element program GARFEM version 3.2 is described in this manual. The program includes, but is not limited to, capabilities to handle the following problems: * Linear bar and beam element structures, * Geometrically non-linear problems (bar and beam), both static and transient dynamic analysis, * Transient response dynamics from a catalog of time varying external forcing function types or input function tables, * Eigenvalue solution (modes and frequencies), * Multi point constraints (MPC) for the modelling of mechanisms and e.g. rigid links. The MPC definition is used only in the geometrically linearized sense, * Beams with disjunct shear axis and neutral axis, * Beams with rigid offset. An interface exist that connects GARFEM with the program GAROS. GAROS is a program for aeroelastic analysis of rotating structures. Since this interface was developed GARFEM now serves as a preprocessor program in place of NASTRAN which was formerly used. Documentation of the methods applied in GARFEM exists but is so far limited to the capacities in existence before the GAROS interface was developed.

  17. Input Shaping to Reduce Solar Array Structural Vibrations

    Science.gov (United States)

    Doherty, Michael J.; Tolson, Robert J.

    1998-01-01

    Structural vibrations induced by actuators can be minimized using input shaping. Input shaping is a feedforward method in which actuator commands are convolved with shaping functions to yield a shaped set of commands. These commands are designed to perform the maneuver while minimizing the residual structural vibration. In this report, input shaping is extended to stepper motor actuators. As a demonstration, an input-shaping technique based on pole-zero cancellation was used to modify the Solar Array Drive Assembly (SADA) actuator commands for the Lewis satellite. A series of impulses were calculated as the ideal SADA output for vibration control. These impulses were then discretized for use by the SADA stepper motor actuator and simulated actuator outputs were used to calculate the structural response. The effectiveness of input shaping is limited by the accuracy of the knowledge of the modal frequencies. Assuming perfect knowledge resulted in significant vibration reduction. Errors of 10% in the modal frequencies caused notably higher levels of vibration. Controller robustness was improved by incorporating additional zeros in the shaping function. The additional zeros did not require increased performance from the actuator. Despite the identification errors, the resulting feedforward controller reduced residual vibrations to the level of the exactly modeled input shaper and well below the baseline cases. These results could be easily applied to many other vibration-sensitive applications involving stepper motor actuators.

  18. Letter position coding across modalities: the case of Braille readers.

    Directory of Open Access Journals (Sweden)

    Manuel Perea

    Full Text Available The question of how the brain encodes letter position in written words has attracted increasing attention in recent years. A number of models have recently been proposed to accommodate the fact that transposed-letter stimuli like jugde or caniso are perceptually very close to their base words.Here we examined how letter position coding is attained in the tactile modality via Braille reading. The idea is that Braille word recognition may provide more serial processing than the visual modality, and this may produce differences in the input coding schemes employed to encode letters in written words. To that end, we conducted a lexical decision experiment with adult Braille readers in which the pseudowords were created by transposing/replacing two letters.We found a word-frequency effect for words. In addition, unlike parallel experiments in the visual modality, we failed to find any clear signs of transposed-letter confusability effects. This dissociation highlights the differences between modalities.The present data argue against models of letter position coding that assume that transposed-letter effects (in the visual modality occur at a relatively late, abstract locus.

  19. Letter position coding across modalities: the case of Braille readers.

    Science.gov (United States)

    Perea, Manuel; García-Chamorro, Cristina; Martín-Suesta, Miguel; Gómez, Pablo

    2012-01-01

    The question of how the brain encodes letter position in written words has attracted increasing attention in recent years. A number of models have recently been proposed to accommodate the fact that transposed-letter stimuli like jugde or caniso are perceptually very close to their base words. Here we examined how letter position coding is attained in the tactile modality via Braille reading. The idea is that Braille word recognition may provide more serial processing than the visual modality, and this may produce differences in the input coding schemes employed to encode letters in written words. To that end, we conducted a lexical decision experiment with adult Braille readers in which the pseudowords were created by transposing/replacing two letters. We found a word-frequency effect for words. In addition, unlike parallel experiments in the visual modality, we failed to find any clear signs of transposed-letter confusability effects. This dissociation highlights the differences between modalities. The present data argue against models of letter position coding that assume that transposed-letter effects (in the visual modality) occur at a relatively late, abstract locus.

  20. Dual ant colony operational modal analysis parameter estimation method

    Science.gov (United States)

    Sitarz, Piotr; Powałka, Bartosz

    2018-01-01

    Operational Modal Analysis (OMA) is a common technique used to examine the dynamic properties of a system. Contrary to experimental modal analysis, the input signal is generated in object ambient environment. Operational modal analysis mainly aims at determining the number of pole pairs and at estimating modal parameters. Many methods are used for parameter identification. Some methods operate in time while others in frequency domain. The former use correlation functions, the latter - spectral density functions. However, while some methods require the user to select poles from a stabilisation diagram, others try to automate the selection process. Dual ant colony operational modal analysis parameter estimation method (DAC-OMA) presents a new approach to the problem, avoiding issues involved in the stabilisation diagram. The presented algorithm is fully automated. It uses deterministic methods to define the interval of estimated parameters, thus reducing the problem to optimisation task which is conducted with dedicated software based on ant colony optimisation algorithm. The combination of deterministic methods restricting parameter intervals and artificial intelligence yields very good results, also for closely spaced modes and significantly varied mode shapes within one measurement point.

  1. Modalities in homotopy type theory

    DEFF Research Database (Denmark)

    Rijke, Egbert; Shulman, Michael; Spitters, Bas

    2017-01-01

    Univalent homotopy type theory (HoTT) may be seen as a language for the category of ∞-groupoids. It is being developed as a new foundation for mathematics and as an internal language for (elementary) higher toposes. We develop the theory of factorization systems, reflective subuniverses......, and modalities in homotopy type theory, including their construction using a "localization" higher inductive type. This produces in particular the (n-connected, n-truncated) factorization system as well as internal presentations of subtoposes, through lex modalities. We also develop the semantics...

  2. GAROS input deck description

    Energy Technology Data Exchange (ETDEWEB)

    Vollan, A.; Soederberg, M. (Aeronautical Research Inst. of Sweden, Bromma (Sweden))

    1989-01-01

    This report describes the input for the programs GAROS1 and GAROS2, version 5.8 and later, February 1988. The GAROS system, developed by Arne Vollan, Omega GmbH, is used for the analysis of the mechanical and aeroelastic properties for general rotating systems. It has been specially designed to meet the requirements of aeroelastic stability and dynamic response of horizontal axis wind energy converters. Some of the special characteristics are: * The rotor may have one or more blades. * The blades may be rigidly attached to the hub, or they may be fully articulated. * The full elastic properties of the blades, the hub, the machine house and the tower are taken into account. * With the same basic model, a number of different analyses can be performed: Snap-shot analysis, Floquet method, transient response analysis, frequency response analysis etc.

  3. Verification of experimental modal modeling using HDR (Heissdampfreaktor) dynamic test data

    International Nuclear Information System (INIS)

    Srinivasan, M.G.; Kot, C.A.; Hsieh, B.J.

    1983-01-01

    Experimental modal modeling involves the determination of the modal parameters of the model of a structure from recorded input-output data from dynamic tests. Though commercial modal analysis algorithms are being widely used in many industries their ability to identify a set of reliable modal parameters of an as-built nuclear power plant structure has not been systematically verified. This paper describes the effort to verify MODAL-PLUS, a widely used modal analysis code, using recorded data from the dynamic tests performed on the reactor building of the Heissdampfreaktor, situated near Frankfurt, Federal Republic of Germany. In the series of dynamic tests on HDR in 1979, the reactor building was subjected to forced vibrations from different types and levels of dynamic excitations. Two sets of HDR containment building input-output data were chosen for MODAL-PLUS analyses. To reduce the influence of nonlinear behavior on the results, these sets were chosen so that the levels of excitation are relatively low and about the same in the two sets. The attempted verification was only partially successful in that only one modal model, with a limited range of validity, could be synthesized and in that the goodness of fit could be verified only in this limited range

  4. The modal logic of forcing

    NARCIS (Netherlands)

    Hamkins, J.D.; Löwe, B.

    2008-01-01

    A set theoretical assertion psi is forceable or possible, written lozenge psi, if psi holds in some forcing extension, and necessary, written square psi, if psi holds in all forcing extensions. In this forcing interpretation of modal logic, we establish that if ZFC is consistent, then the

  5. Direct calculation of modal contributions to thermal conductivity via Green–Kubo modal analysis

    International Nuclear Information System (INIS)

    Lv, Wei; Henry, Asegun

    2016-01-01

    We derived a new method for direct calculation of the modal contributions to thermal conductivity, which is termed Green–Kubo modal analysis (GKMA). The GKMA method combines the lattice dynamics formalism with the Green–Kubo formula for thermal conductivity, such that the thermal conductivity becomes a direct summation of modal contributions, where one need not define the phonon velocity. As a result, the GKMA method can be applied to any material/group of atoms, where the atoms vibrate around stable equilibrium positions, which includes non-stoichiometric compounds, random alloys, amorphous materials and even rigid molecules. By using molecular dynamics simulations to obtain the time history of each mode’s contribution to the heat current, one naturally includes anharmonicity to full order and can obtain insight into the interactions between different modes through the cross-correlations. As an example, we applied the GMKA method to crystalline and amorphous silicon. The modal contributions at each frequency result from the analysis and thereby allow one to apply a quantum correction to the mode heat capacity to determine the temperature dependence of thermal conductivity. The predicted temperature dependent thermal conductivity for amorphous silicon shows the best agreement with experiments to date. The GKMA method provides new insight into the nature of phonon transport, as it casts the problem in terms of mode–mode correlation instead of scattering, and provides a general unified formalism that can be used to understand phonon–phonon interactions in essentially any class of materials or structures where the atoms vibrate around stable equilibrium sites. (paper)

  6. Modeling and generating input processes

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, M.E.

    1987-01-01

    This tutorial paper provides information relevant to the selection and generation of stochastic inputs to simulation studies. The primary area considered is multivariate but much of the philosophy at least is relevant to univariate inputs as well. 14 refs.

  7. Reprocessing input data validation

    International Nuclear Information System (INIS)

    Persiani, P.J.; Bucher, R.G.; Pond, R.B.; Cornella, R.J.

    1990-01-01

    The Isotope Correlation Technique (ICT), in conjunction with the gravimetric (Pu/U ratio) method for mass determination, provides an independent verification of the input accountancy at the dissolver or accountancy stage of the reprocessing plant. The Isotope Correlation Technique has been applied to many classes of domestic and international reactor systems (light-water, heavy-water, graphite, and liquid-metal) operating in a variety of modes (power, research, production, and breeder), and for a variety of reprocessing fuel cycle management strategies. Analysis of reprocessing operations data based on isotopic correlations derived for assemblies in a PWR environment and fuel management scheme, yielded differences between the measurement-derived and ICT-derived plutonium mass determinations of (-0.02 ± 0.23)% for the measured U-235 and (+0.50 ± 0.31)% for the measured Pu-239, for a core campaign. The ICT analyses has been implemented for the plutonium isotopics in a depleted uranium assembly in a heavy-water, enriched uranium system and for the uranium isotopes in the fuel assemblies in light-water, highly-enriched systems. 7 refs., 5 figs., 4 tabs

  8. Adding Pluggable and Personalized Natural Control Capabilities to Existing Applications

    Science.gov (United States)

    Lamberti, Fabrizio; Sanna, Andrea; Carlevaris, Gilles; Demartini, Claudio

    2015-01-01

    Advancements in input device and sensor technologies led to the evolution of the traditional human-machine interaction paradigm based on the mouse and keyboard. Touch-, gesture- and voice-based interfaces are integrated today in a variety of applications running on consumer devices (e.g., gaming consoles and smartphones). However, to allow existing applications running on desktop computers to utilize natural interaction, significant re-design and re-coding efforts may be required. In this paper, a framework designed to transparently add multi-modal interaction capabilities to applications to which users are accustomed is presented. Experimental observations confirmed the effectiveness of the proposed framework and led to a classification of those applications that could benefit more from the availability of natural interaction modalities. PMID:25635410

  9. Utilizing Multi-Modal Literacies in Middle Grades Science

    Science.gov (United States)

    Saurino, Dan; Ogletree, Tamra; Saurino, Penelope

    2010-01-01

    The nature of literacy is changing. Increased student use of computer-mediated, digital, and visual communication spans our understanding of adolescent multi-modal capabilities that reach beyond the traditional conventions of linear speech and written text in the science curriculum. Advancing technology opens doors to learning that involve…

  10. Does it really matter whether students' contributions are spoken versus typed in an intelligent tutoring system with natural language?

    Science.gov (United States)

    D'Mello, Sidney K; Dowell, Nia; Graesser, Arthur

    2011-03-01

    There is the question of whether learning differs when students speak versus type their responses when interacting with intelligent tutoring systems with natural language dialogues. Theoretical bases exist for three contrasting hypotheses. The speech facilitation hypothesis predicts that spoken input will increase learning, whereas the text facilitation hypothesis predicts typed input will be superior. The modality equivalence hypothesis claims that learning gains will be equivalent. Previous experiments that tested these hypotheses were confounded by automated speech recognition systems with substantial error rates that were detected by learners. We addressed this concern in two experiments via a Wizard of Oz procedure, where a human intercepted the learner's speech and transcribed the utterances before submitting them to the tutor. The overall pattern of the results supported the following conclusions: (1) learning gains associated with spoken and typed input were on par and quantitatively higher than a no-intervention control, (2) participants' evaluations of the session were not influenced by modality, and (3) there were no modality effects associated with differences in prior knowledge and typing proficiency. Although the results generally support the modality equivalence hypothesis, highly motivated learners reported lower cognitive load and demonstrated increased learning when typing compared with speaking. We discuss the implications of our findings for intelligent tutoring systems that can support typed and spoken input.

  11. Quantum supports and modal logic

    International Nuclear Information System (INIS)

    Svetlichny, G.

    1986-01-01

    Recently Foulis, Piron, and Randall introduced a new interpretation of empirical and quantum logics which substitute for the notion of a probabilistic weight a combinatorial notion called a support. The informal use of the notion of ''possible outcomes of experiments'' suggests that this interpretation can be related to corresponding formal notions as treated by modal logic. The purpose of this paper is to prove that in fact supports are in one-to-one correspondence with the sets of possibly true elementary propositions in Kripke models of a set of modal formulas associated to the empirical or quantum logic. This hopefully provides a sufficiently detailed link between the two rather distinct logical systems to shed useful light on both

  12. Modal abstractions of concurrent behavior

    DEFF Research Database (Denmark)

    Nielson, Flemming; Nanz, Sebastian; Nielson, Hanne Riis

    2011-01-01

    We present an effective algorithm for the automatic construction of finite modal transition systems as abstractions of potentially infinite concurrent processes. Modal transition systems are recognized as valuable abstractions for model checking because they allow for the validation as well...... as refutation of safety and liveness properties. However, the algorithmic construction of finite abstractions from potentially infinite concurrent processes is a missing link that prevents their more widespread usage for model checking of concurrent systems. Our algorithm is a worklist algorithm using concepts...... from abstract interpretation and operating upon mappings from sets to intervals in order to express simultaneous over- and underapprox-imations of the multisets of process actions available in a particular state. We obtain a finite abstraction that is 3-valued in both states and transitions...

  13. A modal specification theory for components with data

    DEFF Research Database (Denmark)

    Bauer, Sebastian S.; Larsen, Kim G.; Legay, Axel

    2014-01-01

    of transitions allows for developing a unique approach for both logical and structural compositions, and eases the step-wise refine- ment process for building implementations. We propose Modal Specifications with Data (MSDs), the first modal specification theory with explicit representation of data. Our new...... theory includes the most commonly seen ingredients of a specification the- ory; that is parallel composition, conjunction and quotient. As MSDs are by nature potentially infinite-state systems, we propose symbolic representations based on effec- tive predicates. Our theory serves as a new abstraction...

  14. Connecting Biology to Electronics: Molecular Communication via Redox Modality.

    Science.gov (United States)

    Liu, Yi; Li, Jinyang; Tschirhart, Tanya; Terrell, Jessica L; Kim, Eunkyoung; Tsao, Chen-Yu; Kelly, Deanna L; Bentley, William E; Payne, Gregory F

    2017-12-01

    Biology and electronics are both expert at for accessing, analyzing, and responding to information. Biology uses ions, small molecules, and macromolecules to receive, analyze, store, and transmit information, whereas electronic devices receive input in the form of electromagnetic radiation, process the information using electrons, and then transmit output as electromagnetic waves. Generating the capabilities to connect biology-electronic modalities offers exciting opportunities to shape the future of biosensors, point-of-care medicine, and wearable/implantable devices. Redox reactions offer unique opportunities for bio-device communication that spans the molecular modalities of biology and electrical modality of devices. Here, an approach to search for redox information through an interactive electrochemical probing that is analogous to sonar is adopted. The capabilities of this approach to access global chemical information as well as information of specific redox-active chemical entities are illustrated using recent examples. An example of the use of synthetic biology to recognize external molecular information, process this information through intracellular signal transduction pathways, and generate output responses that can be detected by electrical modalities is also provided. Finally, exciting results in the use of redox reactions to actuate biology are provided to illustrate that synthetic biology offers the potential to guide biological response through electrical cues. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  15. Training Modalities to Increase Sensorimotor Adaptability

    Science.gov (United States)

    Bloomberg, J. J.; Mulavara, A. P.; Peters, B. T.; Brady, R.; Audas, C.; Cohen, H. S.

    2009-01-01

    During the acute phase of adaptation to novel gravitational environments, sensorimotor disturbances have the potential to disrupt the ability of astronauts to perform required mission tasks. The goal of our current series of studies is develop a sensorimotor adaptability (SA) training program designed to facilitate recovery of functional capabilities when astronauts transition to different gravitational environments. The project has conducted a series of studies investigating the efficacy of treadmill training combined with a variety of sensory challenges (incongruent visual input, support surface instability) designed to increase adaptability. SA training using a treadmill combined with exposure to altered visual input was effective in producing increased adaptability in a more complex over-ground ambulatory task on an obstacle course. This confirms that for a complex task like walking, treadmill training contains enough of the critical features of overground walking to be an effective training modality. SA training can be optimized by using a periodized training schedule. Test sessions that each contain short-duration exposures to multiple perturbation stimuli allows subjects to acquire a greater ability to rapidly reorganize appropriate response strategies when encountering a novel sensory environment. Using a treadmill mounted on top of a six degree-of-freedom motion base platform we investigated locomotor training responses produced by subjects introduced to a dynamic walking surface combined with alterations in visual flow. Subjects who received this training had improved locomotor performance and faster reaction times when exposed to the novel sensory stimuli compared to control subjects. Results also demonstrate that individual sensory biases (i.e. increased visual dependency) can predict adaptive responses to novel sensory environments suggesting that individual training prescription can be developed to enhance adaptability. These data indicate that SA

  16. A modal characterization of Peirce algebras

    NARCIS (Netherlands)

    M. de Rijke (Maarten)

    1995-01-01

    textabstractPeirce algebras combine sets, relations and various operations linking the two in a unifying setting.This note offers a modal perspective on Peirce algebras.It uses modal logic to characterize the full Peirce algebras.

  17. Combined modalities: chemotherapy/radiotherapy. Meeting summary

    International Nuclear Information System (INIS)

    Phillips, T.L.

    1979-01-01

    The effects of combined modalities, the standardization of terminology, the mechanisms of chemotherapeutic interactions with radiation and responses of normal and tumor systems are summarized from information presented at the Conference on Combined Modalities

  18. Tailoring distributed modal sensors for in-plane modal filtering

    International Nuclear Information System (INIS)

    Donoso, A; Bellido, J C

    2009-01-01

    In this note we deal with finding the shape of distributed piezoelectric modal sensors for isolating the in-plane mode shapes of plates. The problem is treated by an optimization approach, in which a binary function is used to model the design variable: the polarization profile of the piezoelectric layer. The numerical procedure proposed here allows us to find polarization profiles which take on two values only, i.e. either positive or negative polarization, that make it possible to isolate particular vibration modes in the frequency domain. (technical note)

  19. Bimodal extinction without cross-modal extinction.

    OpenAIRE

    Inhoff, A W; Rafal, R D; Posner, M J

    1992-01-01

    Three patients with unilateral neurological injury were clinically examined. All showed consistent unilateral extinction in the tactile and visual modalities on simultaneous intramodal stimulation. There was virtually no evidence for cross-modal extinction, however, so that contralateral stimulation of one modality would have extinguished perception of ipsilateral stimuli in the other modality. It is concluded that the attentional system controlling the encoding of tactile and visual stimuli ...

  20. Modular sequent calculi for classical modal logics

    NARCIS (Netherlands)

    Gilbert, David; Maffezioli, Paolo

    This paper develops sequent calculi for several classical modal logics. Utilizing a polymodal translation of the standard modal language, we are able to establish a base system for the minimal classical modal logic E from which we generate extensions (to include M, C, and N) in a modular manner. Our

  1. Completeness for flat modal fixpoint logics

    NARCIS (Netherlands)

    Santocanale, L.; Venema, Y.

    2010-01-01

    This paper exhibits a general and uniform method to prove axiomatic completeness for certain modal fixpoint logics. Given a set Γ of modal formulas of the form γ(x,p1,…,pn), where x occurs only positively in γ, we obtain the flat modal fixpoint language L♯(Γ) by adding to the language of polymodal

  2. Modal Processor Effects Inspired by Hammond Tonewheel Organs

    Directory of Open Access Journals (Sweden)

    Kurt James Werner

    2016-06-01

    Full Text Available In this design study, we introduce a novel class of digital audio effects that extend the recently introduced modal processor approach to artificial reverberation and effects processing. These pitch and distortion processing effects mimic the design and sonics of a classic additive-synthesis-based electromechanical musical instrument, the Hammond tonewheel organ. As a reverb effect, the modal processor simulates a room response as the sum of resonant filter responses. This architecture provides precise, interactive control over the frequency, damping, and complex amplitude of each mode. Into this framework, we introduce two types of processing effects: pitch effects inspired by the Hammond organ’s equal tempered “tonewheels”, “drawbar” tone controls, vibrato/chorus circuit, and distortion effects inspired by the pseudo-sinusoidal shape of its tonewheels and electromagnetic pickup distortion. The result is an effects processor that imprints the Hammond organ’s sonics onto any audio input.

  3. STRATEGIC AND ECONOMIC MODALITY OF ENVIRONMENTAL DIPLOMACY

    Directory of Open Access Journals (Sweden)

    А. Bokhan

    2018-01-01

    Full Text Available Modern development of humanity and its well-being is measured by the parameters of progressive achievements, global resonance and ecological warnings. XXI century, forming a new architecture of the world economy, which requires countries to resource diversification, market innovation and modification of the concept of leadership in combinatorial forms of competition and confrontation, consolidation and partnership. The dialogue of civilizations always contains contradictions and demonstrates the relative stability of communities in terms of ecological risk. International politicians are calling for the approval of constructivism economic activities on the basis of environmental diplomacy. Purpose. Determination of activation modality stratagem environmental diplomacy in the context of consolidating the areas of international economic relations, globalization challenges and opportunities. Result. New aspirations of humankind radically change the idea of naturalness and safety of its habitat, increase the importance of information and technological attributes of activity, cause the reactionary nature of the scale of the economic confrontation. Pause economic and technological expansionism unrealistic, but to channel the energy in a more environmental expansionism direction is necessary. Great hopes are placed on the active forms of diplomacy based on multi-level mobility of its subjects and ecological factors strengthen countries stratification. Traditionally, diplomacy is synchronized with the negotiation process, which are presented to the interests and intentions, tactics and strategy of the leaders of the political and business elite of the world. The development of environmental analysis diplomacy takes place under the pressure of massive information flows, multinational business interests and ideology of the hybrid wars. Environmental diplomacy is able to set the modality (way hypothetical implementation, realistic, pragmatic and forward

  4. Linear Subspace Ranking Hashing for Cross-Modal Retrieval.

    Science.gov (United States)

    Li, Kai; Qi, Guo-Jun; Ye, Jun; Hua, Kien A

    2017-09-01

    Hashing has attracted a great deal of research in recent years due to its effectiveness for the retrieval and indexing of large-scale high-dimensional multimedia data. In this paper, we propose a novel ranking-based hashing framework that maps data from different modalities into a common Hamming space where the cross-modal similarity can be measured using Hamming distance. Unlike existing cross-modal hashing algorithms where the learned hash functions are binary space partitioning functions, such as the sign and threshold function, the proposed hashing scheme takes advantage of a new class of hash functions closely related to rank correlation measures which are known to be scale-invariant, numerically stable, and highly nonlinear. Specifically, we jointly learn two groups of linear subspaces, one for each modality, so that features' ranking orders in different linear subspaces maximally preserve the cross-modal similarities. We show that the ranking-based hash function has a natural probabilistic approximation which transforms the original highly discontinuous optimization problem into one that can be efficiently solved using simple gradient descent algorithms. The proposed hashing framework is also flexible in the sense that the optimization procedures are not tied up to any specific form of loss function, which is typical for existing cross-modal hashing methods, but rather we can flexibly accommodate different loss functions with minimal changes to the learning steps. We demonstrate through extensive experiments on four widely-used real-world multimodal datasets that the proposed cross-modal hashing method can achieve competitive performance against several state-of-the-arts with only moderate training and testing time.

  5. Modal Structures in flow past a cylinder

    Science.gov (United States)

    Murshed, Mohammad

    2017-11-01

    With the advent of data, there have been opportunities to apply formalism to detect patterns or simple relations. For instance, a phenomenon can be defined through a partial differential equation which may not be very useful right away, whereas a formula for the evolution of a primary variable may be interpreted quite easily. Having access to data is not enough to move on since doing advanced linear algebra can put strain on the way computations are being done. A canonical problem in the field of aerodynamics is the transient flow past a cylinder where the viscosity can be adjusted to set the Reynolds number (Re). We observe the effect of the critical Re on the certain modes of behavior in time scale. A 2D-velocity field works as an input to analyze the modal structure of the flow using the Proper Orthogonal Decomposition and Koopman Mode/Dynamic Mode Decomposition. This will enable prediction of the solution further in time (taking into account the dependence on Re) and help us evaluate and discuss the associated error in the mechanism.

  6. Physical modalities in chronic pain management.

    Science.gov (United States)

    Rakel, Barbara; Barr, John O

    2003-09-01

    The following conclusions can be made based on review of the evidence: There is limited but positive evidence that select physical modalities are effective in managing chronic pain associated with specific conditions experienced by adults and older individuals. Overall, studies have provided the most support for the modality of therapeutic exercise. Different physical modalities have similar magnitudes of effects on chronic pain. Therefore, selection of the most appropriate physical modality may depend on the desired functional outcome for the patient, the underlying impairment, and the patient's preference or prior experience with the modality. Certain patient characteristics may decrease the effectiveness of physical modalities, as has been seen with TENS. These characteristics include depression, high trait anxiety, a powerful others locus of control, obesity, narcotic use, and neuroticism. The effect on pain by various modalities is generally strongest in the short-term period immediately after the intervention series, but effects can last as long as 1 year after treatment (e.g., with massage). Most research has tested the effect of physical modalities on chronic low back pain and knee OA. The effectiveness of physical modalities for other chronic pain conditions needs to be evaluated more completely. Older and younger adults often experience similar effects on their perception of pain from treatment with physical modalities. Therefore, use of these modalities for chronic pain in older adults is appropriate, but special precautions need to be taken. Practitioners applying physical modalities need formal training that includes the risks and precautions for these modalities. If practitioners lack formal training in the use of physical modalities, or if modality use is not within their scope of practice, it is important to consult with and refer patients to members of the team who have this specialized training. Use of a multidisciplinary approach to chronic pain

  7. Limitations of modal analysis of damped structures

    International Nuclear Information System (INIS)

    Krapf, K.G.; Woelfel, H.

    1983-01-01

    Quite recently discrete spring-damper elements are increasingly used for the low-tuned supports of nuclear power-plant buildings and equipment (reactor building, turbine-fundaments etc.) to reduce the vibration response due to the dynamic load cases earthquake and airplane crash. Because of this development, it is to be investigated whether the usual modal analysis method is applicable within the design process or should be changed respectively replaced in special cases. The paper contributes to this discussion by demonstrating and valuing the discrepancies in the different ways for the implementation of damping. Different methods for uncoupling (energy weighting, reduction to Rayleigh-damping) are compared with the solution of the coupled equations of motion. In particular vertical vibrations of a spring-damper-supported building on foundation (including ground springs) are examined using a two-degree-of-freedom-system. The results of coupled and (by force) uncoupled methods are interpreted concerning free vibration by comparison of the damping of natural vibrations, natural frequencies and natural mode shapes. The effect on the forced vibrations is shown by floor response spectra to an earthquake accelerogram. (orig./HP)

  8. Noise elimination algorithm for modal analysis

    Energy Technology Data Exchange (ETDEWEB)

    Bao, X. X., E-mail: baoxingxian@upc.edu.cn [Department of Naval Architecture and Ocean Engineering, China University of Petroleum (East China), Qingdao 266580 (China); Li, C. L. [Key Laboratory of Marine Geology and Environment, Institute of Oceanology, Chinese Academy of Sciences, Qingdao 266071 (China); Xiong, C. B. [The First Institute of Oceanography, State Oceanic Administration, Qingdao 266061 (China)

    2015-07-27

    Modal analysis is an ongoing interdisciplinary physical issue. Modal parameters estimation is applied to determine the dynamic characteristics of structures under vibration excitation. Modal analysis is more challenging for the measured vibration response signals are contaminated with noise. This study develops a mathematical algorithm of structured low rank approximation combined with the complex exponential method to estimate the modal parameters. Physical experiments using a steel cantilever beam with ten accelerometers mounted, excited by an impulse load, demonstrate that this method can significantly eliminate noise from measured signals and accurately identify the modal frequencies and damping ratios. This study provides a fundamental mechanism of noise elimination using structured low rank approximation in physical fields.

  9. Modality and Task Switching Interactions using Bi-Modal and Bivalent Stimuli

    Science.gov (United States)

    Sandhu, Rajwant; Dyson, Benjamin J.

    2013-01-01

    Investigations of concurrent task and modality switching effects have to date been studied under conditions of uni-modal stimulus presentation. As such, it is difficult to directly compare resultant task and modality switching effects, as the stimuli afford both tasks on each trial, but only one modality. The current study investigated task and…

  10. The modal surface interpolation method for damage localization

    Science.gov (United States)

    Pina Limongelli, Maria

    2017-05-01

    The Interpolation Method (IM) has been previously proposed and successfully applied for damage localization in plate like structures. The method is based on the detection of localized reductions of smoothness in the Operational Deformed Shapes (ODSs) of the structure. The IM can be applied to any type of structure provided the ODSs are estimated accurately in the original and in the damaged configurations. If the latter circumstance fails to occur, for example when the structure is subjected to an unknown input(s) or if the structural responses are strongly corrupted by noise, both false and missing alarms occur when the IM is applied to localize a concentrated damage. In order to overcome these drawbacks a modification of the method is herein investigated. An ODS is the deformed shape of a structure subjected to a harmonic excitation: at resonances the ODS are dominated by the relevant mode shapes. The effect of noise at resonance is usually lower with respect to other frequency values hence the relevant ODS are estimated with higher reliability. Several methods have been proposed to reliably estimate modal shapes in case of unknown input. These two circumstances can be exploited to improve the reliability of the IM. In order to reduce or eliminate the drawbacks related to the estimation of the ODSs in case of noisy signals, in this paper is investigated a modified version of the method based on a damage feature calculated considering the interpolation error relevant only to the modal shapes and not to all the operational shapes in the significant frequency range. Herein will be reported the comparison between the results of the IM in its actual version (with the interpolation error calculated summing up the contributions of all the operational shapes) and in the new proposed version (with the estimation of the interpolation error limited to the modal shapes).

  11. Enhanced Input in LCTL Pedagogy

    Directory of Open Access Journals (Sweden)

    Marilyn S. Manley

    2009-08-01

    Full Text Available Language materials for the more-commonly-taught languages (MCTLs often include visual input enhancement (Sharwood Smith 1991, 1993 which makes use of typographical cues like bolding and underlining to enhance the saliency of targeted forms. For a variety of reasons, this paper argues that the use of enhanced input, both visual and oral, is especially important as a tool for the lesscommonly-taught languages (LCTLs. As there continues to be a scarcity of teaching resources for the LCTLs, individual teachers must take it upon themselves to incorporate enhanced input into their own self-made materials. Specific examples of how to incorporate both visual and oral enhanced input into language teaching are drawn from the author’s own experiences teaching Cuzco Quechua. Additionally, survey results are presented from the author’s Fall 2010 semester Cuzco Quechua language students, supporting the use of both visual and oral enhanced input.

  12. Enhanced Input in LCTL Pedagogy

    Directory of Open Access Journals (Sweden)

    Marilyn S. Manley

    2010-08-01

    Full Text Available Language materials for the more-commonly-taught languages (MCTLs often include visual input enhancement (Sharwood Smith 1991, 1993 which makes use of typographical cues like bolding and underlining to enhance the saliency of targeted forms. For a variety of reasons, this paper argues that the use of enhanced input, both visual and oral, is especially important as a tool for the lesscommonly-taught languages (LCTLs. As there continues to be a scarcity of teaching resources for the LCTLs, individual teachers must take it upon themselves to incorporate enhanced input into their own self-made materials. Specific examples of how to incorporate both visual and oral enhanced input into language teaching are drawn from the author’s own experiences teaching Cuzco Quechua. Additionally, survey results are presented from the author’s Fall 2010 semester Cuzco Quechua language students, supporting the use of both visual and oral enhanced input.

  13. Multi-modal locomotion: from animal to application

    International Nuclear Information System (INIS)

    Lock, R J; Burgess, S C; Vaidyanathan, R

    2014-01-01

    The majority of robotic vehicles that can be found today are bound to operations within a single media (i.e. land, air or water). This is very rarely the case when considering locomotive capabilities in natural systems. Utility for small robots often reflects the exact same problem domain as small animals, hence providing numerous avenues for biological inspiration. This paper begins to investigate the various modes of locomotion adopted by different genus groups in multiple media as an initial attempt to determine the compromise in ability adopted by the animals when achieving multi-modal locomotion. A review of current biologically inspired multi-modal robots is also presented. The primary aim of this research is to lay the foundation for a generation of vehicles capable of multi-modal locomotion, allowing ambulatory abilities in more than one media, surpassing current capabilities. By identifying and understanding when natural systems use specific locomotion mechanisms, when they opt for disparate mechanisms for each mode of locomotion rather than using a synergized singular mechanism, and how this affects their capability in each medium, similar combinations can be used as inspiration for future multi-modal biologically inspired robotic platforms. (topical review)

  14. Examination of Successful Modal Analysis Techniques Used for Bladed-Disk Assemblies

    National Research Council Canada - National Science Library

    Orsagh, R

    2002-01-01

    Modal testing of bladed-disk assemblies in turbomachines is used to identify the critical natural frequencies and mode shape information used for avoiding the per-rev resonant conditions that cause high cycle fatigue (HCF...

  15. Predicting wind-induced vibrations of high-rise buildings using unsteady CFD and modal analysis

    KAUST Repository

    Zhang, Yue; Habashi, Wagdi G (Ed); Khurram, Rooh Ul Amin

    2015-01-01

    This paper investigates the wind-induced vibration of the CAARC standard tall building model, via unsteady Computational Fluid Dynamics (CFD) and a structural modal analysis. In this numerical procedure, the natural unsteady wind in the atmospheric

  16. Integration of auditory and tactile inputs in musical meter perception.

    Science.gov (United States)

    Huang, Juan; Gamble, Darik; Sarnlertsophon, Kristine; Wang, Xiaoqin; Hsiao, Steven

    2013-01-01

    Musicians often say that they not only hear but also "feel" music. To explore the contribution of tactile information to "feeling" music, we investigated the degree that auditory and tactile inputs are integrated in humans performing a musical meter-recognition task. Subjects discriminated between two types of sequences, "duple" (march-like rhythms) and "triple" (waltz-like rhythms), presented in three conditions: (1) unimodal inputs (auditory or tactile alone); (2) various combinations of bimodal inputs, where sequences were distributed between the auditory and tactile channels such that a single channel did not produce coherent meter percepts; and (3) bimodal inputs where the two channels contained congruent or incongruent meter cues. We first show that meter is perceived similarly well (70-85 %) when tactile or auditory cues are presented alone. We next show in the bimodal experiments that auditory and tactile cues are integrated to produce coherent meter percepts. Performance is high (70-90 %) when all of the metrically important notes are assigned to one channel and is reduced to 60 % when half of these notes are assigned to one channel. When the important notes are presented simultaneously to both channels, congruent cues enhance meter recognition (90 %). Performance dropped dramatically when subjects were presented with incongruent auditory cues (10 %), as opposed to incongruent tactile cues (60 %), demonstrating that auditory input dominates meter perception. These observations support the notion that meter perception is a cross-modal percept with tactile inputs underlying the perception of "feeling" music.

  17. Experimental Modal Test of the Laboratory Model of Steel Truss Structure

    Directory of Open Access Journals (Sweden)

    Kortiš Ján

    2016-12-01

    Full Text Available The experimental modal analysis is often used to validate the accuracy of dynamic numerical models. It is also a good tool to obtain valuable information about current condition of the structures that could help to determine residual lifetime. The quality of modal testing results is highly dependent on the proper estimation of the natural frequencies from the frequency response function. This article presents the experimental modal test of the laboratory steel structure in which the natural frequencies and mode shapes are determined.

  18. Modality-Constrained Statistical Learning of Tactile, Visual, and Auditory Sequences

    Science.gov (United States)

    Conway, Christopher M.; Christiansen, Morten H.

    2005-01-01

    The authors investigated the extent to which touch, vision, and audition mediate the processing of statistical regularities within sequential input. Few researchers have conducted rigorous comparisons across sensory modalities; in particular, the sense of touch has been virtually ignored. The current data reveal not only commonalities but also…

  19. Phasing Out a Polluting Input

    OpenAIRE

    Eriksson, Clas

    2015-01-01

    This paper explores economic policies related to the potential conflict between economic growth and the environment. It applies a model with directed technological change and focuses on the case with low elasticity of substitution between clean and dirty inputs in production. New technology is substituted for the polluting input, which results in a gradual decline in pollution along the optimal long-run growth path. In contrast to some recent work, the era of pollution and environmental polic...

  20. A modal analysis of flexible aircraft dynamics with handling qualities implications

    Science.gov (United States)

    Schmidt, D. K.

    1983-01-01

    A multivariable modal analysis technique is presented for evaluating flexible aircraft dynamics, focusing on meaningful vehicle responses to pilot inputs and atmospheric turbulence. Although modal analysis is the tool, vehicle time response is emphasized, and the analysis is performed on the linear, time-domain vehicle model. In evaluating previously obtained experimental pitch tracking data for a family of vehicle dynamic models, it is shown that flexible aeroelastic effects can significantly affect pitch attitude handling qualities. Consideration of the eigenvalues alone, of both rigid-body and aeroelastic modes, does not explain the simulation results. Modal analysis revealed, however, that although the lowest aeroelastic mode frequency was still three times greater than the short-period frequency, the rigid-body attitude response was dominated by this aeroelastic mode. This dominance was defined in terms of the relative magnitudes of the modal residues in selected vehicle responses.

  1. Wood-gas / natural-gas combined-cycle power station for Switzerland - Potential and estimation of financial viability; Holzgas/Erdgas-Kombikraftwerk fuer die Schweiz: Potenzial und Wirtschaftlichkeitsabschaetzung. Input-Papier fuer die Stromangebots-Perspektiven 2035 des Bundesamts fuer Energie

    Energy Technology Data Exchange (ETDEWEB)

    Nussbaumer, T.

    2005-07-01

    This paper was produced as an input to the Swiss Confederation's 'Electricity Perspectives 2035' study made by the Swiss Federal Office of Energy (SFOE). A concept for the combined use of wood and natural gas in a combined-cycle power station is presented. The gasification of wood to provide fuel for the gas turbines and waste-heat boilers of such power stations is proposed as an alternative to just burning wood to provide heat for steam generators. Figures are quoted on the quantities of biomass and wood usable for energy applications in Switzerland. The energetic and financial efficiencies of wood-powered generation of heat and electricity are examined, as are the investments necessary and the costs incurred. Comparisons are presented between wood from forests, sawmill-wastes, scrap wood and natural gas as fuels.

  2. Input preshaping with frequency domain information for flexible-link manipulator control

    Science.gov (United States)

    Tzes, Anthony; Englehart, Matthew J.; Yurkovich, Stephen

    1989-01-01

    The application of an input preshaping scheme to flexible manipulators is considered. The resulting control corresponds to a feedforward term that convolves in real-time the desired reference input with a sequence of impulses and produces a vibration free output. The robustness of the algorithm with respect to injected disturbances and modal frequency variations is not satisfactory and can be improved by convolving the input with a longer sequence of impulses. The incorporation of the preshaping scheme to a closed-loop plant, using acceleration feedback, offers satisfactory disturbance rejection due to feedback and cancellation of the flexible mode effects due to the preshaping. A frequency domain identification scheme is used to estimate the modal frequencies on-line and subsequently update the spacing between the impulses. The combined adaptive input preshaping scheme provides the fastest possible slew that results in a vibration free output.

  3. Modal Testing of the NPSAT1 Engineering Development Unit

    Science.gov (United States)

    2012-07-01

    erkläre ich, dass die vorliegende Master Arbeit von mir selbstständig und nur unter Verwendung der angegebenen Quellen und Hilfsmittel angefertigt...logarithmic scale . As 5 Figure 2 shows, natural frequencies are indicated by large values of the first CMIF (peaks), and multiple modes can be detected by...structure’s behavior. Ewins even states, “that no large- scale modal test should be permitted to proceed until some preliminary SDOF analyses have

  4. Condition Monitoring Of Operating Pipelines With Operational Modal Analysis Application

    OpenAIRE

    Mironov Aleksey; Doronkin Pavel; Priklonsky Aleksander; Kabashkin Igor

    2015-01-01

    In the petroleum, natural gas and petrochemical industries, great attention is being paid to safety, reliability and maintainability of equipment. There are a number of technologies to monitor, control, and maintain gas, oil, water, and sewer pipelines. The paper focuses on operational modal analysis (OMA) application for condition monitoring of operating pipelines. Special focus is on the topicality of OMA for definition of the dynamic features of the pipeline (frequencies and mode shapes) i...

  5. Experienced Sensory Modalities in Dream Recall

    OpenAIRE

    岡田, 斉

    2000-01-01

    The purpose of the present study is to survey the frequency of visual, auditory, kinaesthetic, cutaneous, organic, gustatory, and olfactory experience in dream recall. A total of 1267 undergraduate students completed a dream recall frequency questionnaire, which contained a question about dream recall frequency and about recall frequency of seven sensory modalities. Results showed that seven sensory modalities were divided into two groups; normally perceived sensory modalities in dreaming, wh...

  6. Multi-modal vibration amplitudes of taut inclined cables due to direct and/or parametric excitation

    Science.gov (United States)

    Macdonald, J. H. G.

    2016-02-01

    Cables are often prone to potentially damaging large amplitude vibrations. The dynamic excitation may be from external loading or motion of the cable ends, the latter including direct excitation, normally from components of end motion transverse to the cable, and parametric excitation induced by axial components of end motion causing dynamic tension variations. Geometric nonlinearity can be important, causing stiffening behaviour and nonlinear modal coupling. Previous analyses of the vibrations, often neglecting sag, have generally dealt with direct and parametric excitation separately or have reverted to numerical solutions of the responses. Here a nonlinear cable model is adopted, applicable to taut cables such as on cable-stayed bridges, that allows for cable inclination, small sag (such that the vibration modes are similar to those of a taut string), multiple modes in both planes and end motion and/or external forcing close to any natural frequency. Based on the method of scaling and averaging it is found that, for sinusoidal inputs and positive damping, non-zero steady state responses can only occur in the modes in each plane with natural frequencies close to the excitation frequency and those with natural frequencies close to half this frequency. Analytical solutions, in the form of non-dimensional polynomial equations, are derived for the steady state vibration amplitudes in up to three modes simultaneously: the directly excited mode, the corresponding nonlinearly coupled mode in the orthogonal plane and a parametrically excited mode with half the natural frequency. The stability of the solutions is also identified. The outputs of the equations are consistent with previous results, where available. Example results from the analytical solutions are presented for a typical inclined bridge cable subject to vertical excitation of the lower end, and they are validated by numerical integration of the equations of motion and against some previous experimental

  7. Modality-Driven Classification and Visualization of Ensemble Variance

    Energy Technology Data Exchange (ETDEWEB)

    Bensema, Kevin; Gosink, Luke; Obermaier, Harald; Joy, Kenneth I.

    2016-10-01

    Advances in computational power now enable domain scientists to address conceptual and parametric uncertainty by running simulations multiple times in order to sufficiently sample the uncertain input space. While this approach helps address conceptual and parametric uncertainties, the ensemble datasets produced by this technique present a special challenge to visualization researchers as the ensemble dataset records a distribution of possible values for each location in the domain. Contemporary visualization approaches that rely solely on summary statistics (e.g., mean and variance) cannot convey the detailed information encoded in ensemble distributions that are paramount to ensemble analysis; summary statistics provide no information about modality classification and modality persistence. To address this problem, we propose a novel technique that classifies high-variance locations based on the modality of the distribution of ensemble predictions. Additionally, we develop a set of confidence metrics to inform the end-user of the quality of fit between the distribution at a given location and its assigned class. We apply a similar method to time-varying ensembles to illustrate the relationship between peak variance and bimodal or multimodal behavior. These classification schemes enable a deeper understanding of the behavior of the ensemble members by distinguishing between distributions that can be described by a single tendency and distributions which reflect divergent trends in the ensemble.

  8. Cross-modal processing in auditory and visual working memory.

    Science.gov (United States)

    Suchan, Boris; Linnewerth, Britta; Köster, Odo; Daum, Irene; Schmid, Gebhard

    2006-02-01

    This study aimed to further explore processing of auditory and visual stimuli in working memory. Smith and Jonides (1997) [Smith, E.E., Jonides, J., 1997. Working memory: A view from neuroimaging. Cogn. Psychol. 33, 5-42] described a modified working memory model in which visual input is automatically transformed into a phonological code. To study this process, auditory and the corresponding visual stimuli were presented in a variant of the 2-back task which involved changes from the auditory to the visual modality and vice versa. Brain activation patterns underlying visual and auditory processing as well as transformation mechanisms were analyzed. Results yielded a significant activation in the left primary auditory cortex associated with transformation of visual into auditory information which reflects the matching and recoding of a stored item and its modality. This finding yields empirical evidence for a transformation of visual input into a phonological code, with the auditory cortex as the neural correlate of the recoding process in working memory.

  9. Model validity and frequency band selection in operational modal analysis

    Science.gov (United States)

    Au, Siu-Kui

    2016-12-01

    Experimental modal analysis aims at identifying the modal properties (e.g., natural frequencies, damping ratios, mode shapes) of a structure using vibration measurements. Two basic questions are encountered when operating in the frequency domain: Is there a mode near a particular frequency? If so, how much spectral data near the frequency can be included for modal identification without incurring significant modeling error? For data with high signal-to-noise (s/n) ratios these questions can be addressed using empirical tools such as singular value spectrum. Otherwise they are generally open and can be challenging, e.g., for modes with low s/n ratios or close modes. In this work these questions are addressed using a Bayesian approach. The focus is on operational modal analysis, i.e., with 'output-only' ambient data, where identification uncertainty and modeling error can be significant and their control is most demanding. The approach leads to 'evidence ratios' quantifying the relative plausibility of competing sets of modeling assumptions. The latter involves modeling the 'what-if-not' situation, which is non-trivial but is resolved by systematic consideration of alternative models and using maximum entropy principle. Synthetic and field data are considered to investigate the behavior of evidence ratios and how they should be interpreted in practical applications.

  10. Cross-modal individual recognition in wild African lions.

    Science.gov (United States)

    Gilfillan, Geoffrey; Vitale, Jessica; McNutt, John Weldon; McComb, Karen

    2016-08-01

    Individual recognition is considered to have been fundamental in the evolution of complex social systems and is thought to be a widespread ability throughout the animal kingdom. Although robust evidence for individual recognition remains limited, recent experimental paradigms that examine cross-modal processing have demonstrated individual recognition in a range of captive non-human animals. It is now highly relevant to test whether cross-modal individual recognition exists within wild populations and thus examine how it is employed during natural social interactions. We address this question by testing audio-visual cross-modal individual recognition in wild African lions (Panthera leo) using an expectancy-violation paradigm. When presented with a scenario where the playback of a loud-call (roaring) broadcast from behind a visual block is incongruent with the conspecific previously seen there, subjects responded more strongly than during the congruent scenario where the call and individual matched. These findings suggest that lions are capable of audio-visual cross-modal individual recognition and provide a useful method for studying this ability in wild populations. © 2016 The Author(s).

  11. Modal characteristics and fatigue strength of compressor blades

    International Nuclear Information System (INIS)

    Kim, Kyung Kook; Lee, Young Shin

    2014-01-01

    High-cycle fatigue (HCF) has been identified as one of the primary causes of gas turbine engine failure. The modal characteristics and endurance strength of a 5 MW gas turbine engine blade developed by Doosan Heavy Industries and Construction Co., Ltd. in HCF fracture were verified through analysis and tests to determine the reliability of the compressor blade. A compressor blade design procedure that considers HCF life was performed in the following order: airfoil and blade profile design, modal analysis, stress distribution test, stress endurance limit test, and fatigue life verification. This study analyzed the Campbell diagram and estimated resonance risk on the basis of the natural frequency analysis and modal test of the compressor blade to guarantee safe and operational reliability. In addition, the maximum stress point of the compressor blade was determined through stress distribution analysis and test. The bonding point of the strain gage was determined by using fatigue test. Stress endurance limit test was performed based on the results of these tests. This research compared and verified the modal characteristics and endurance strengths of the compressor blades to prevent HCF fracture, which is among the major causes of gas turbine engine damage. A fatigue life design procedure of compressor blades was established. The 5 MW class gas turbine compressor blade is well designed in terms of resonance stability and fatigue endurance limit.

  12. Modal characteristics and fatigue strength of compressor blades

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Kyung Kook [Doosan Heavy Industries and Construction, Changwon (Korea, Republic of); Lee, Young Shin [Chungnam National University, Daejeon (Korea, Republic of)

    2014-04-15

    High-cycle fatigue (HCF) has been identified as one of the primary causes of gas turbine engine failure. The modal characteristics and endurance strength of a 5 MW gas turbine engine blade developed by Doosan Heavy Industries and Construction Co., Ltd. in HCF fracture were verified through analysis and tests to determine the reliability of the compressor blade. A compressor blade design procedure that considers HCF life was performed in the following order: airfoil and blade profile design, modal analysis, stress distribution test, stress endurance limit test, and fatigue life verification. This study analyzed the Campbell diagram and estimated resonance risk on the basis of the natural frequency analysis and modal test of the compressor blade to guarantee safe and operational reliability. In addition, the maximum stress point of the compressor blade was determined through stress distribution analysis and test. The bonding point of the strain gage was determined by using fatigue test. Stress endurance limit test was performed based on the results of these tests. This research compared and verified the modal characteristics and endurance strengths of the compressor blades to prevent HCF fracture, which is among the major causes of gas turbine engine damage. A fatigue life design procedure of compressor blades was established. The 5 MW class gas turbine compressor blade is well designed in terms of resonance stability and fatigue endurance limit.

  13. Modalities of hemodialysis: Quality improvement

    Directory of Open Access Journals (Sweden)

    Ayman Karkar

    2012-01-01

    Full Text Available Hemodialysis (HD treatment had, over many years, improved the survival rate of patients with end-stage renal disease. However, standard or conventional HD prescription is far from being optimal in replacing the function of normal kidneys. Its unphysiologic clearance pattern and inability to remove all types and sizes of uremic toxins results in inter- and intra-dialysis complications and an unacceptably high rate of cardiovascular morbidity and mortality. Efficiency of HD can be improved by increasing blood and dialysate flow rates, dialyzer size and surface area and duration and frequency of dialysis sessions. Home HD, where short daily or long slow nocturnal HD sessions can conveniently be performed, provides an excellent option for quality of life improvement and reduction in morbidity and mortality. Recent innovations in the specifications of HD machines and improvement in dialysis membranes characteristics and water treatment technology paved the way for achieving quality HD. These advancements have resulted in efficient implementation of adsorption, diffusion and/or convection principles using adsorption HD, hemofiltration, hemodiafiltration (HDF and online HDF modalities in order to achieve optimum HD. Implementation of these innovations resulted in better quality care achievements in clinical practice and reduction in morbidity and mortality rates among HD patients.

  14. A study on identification of nonlinear structure by experimental modal analysis

    International Nuclear Information System (INIS)

    Sone, Akira; Suzuki, Kohei; Nakamura, Hajime.

    1990-01-01

    In this paper, identification techniques based on the experimental modal analysis for the equivalent modal parameters of nonlinear structures are examined from a practical viewpoint. First, using a simple cantilever model with gap or friction at the supported end, the gain characteristics of transfer function are evaluated through the sinusoidal sweep test and random wave test. Second, the equivalent modal parameters such as natural frequency and damping ratio are estimated by two types of identification techniques: ARMA (autoregressive/moving average) model fitting and curve fitting with iterative calculations. From the comparison of the response of the model obtained by the random excitation test and numerical calculation using the equivalent modal parameters, it has been clarified that the ARMA model fitting can be applied to linearized modal parameter identification for nonlinear structures. (author)

  15. Sensor placement optimization for structural modal identification of flexible structures using genetic algorithm

    International Nuclear Information System (INIS)

    Jung, B. K.; Cho, J. R.; Jeong, W. B.

    2015-01-01

    The position of vibration sensors influences the modal identification quality of flexible structures for a given number of sensors, and the quality of modal identification is usually estimated in terms of correlation between the natural modes using the modal assurance criterion (MAC). The sensor placement optimization is characterized by the fact that the design variables are not continuous but discrete, implying that the conventional sensitivity-driven optimization methods are not applicable. In this context, this paper presents the application of genetic algorithm to the sensor placement optimization for improving the modal identification quality of flexible structures. A discrete-type optimization problem using genetic algorithm is formulated by defining the sensor positions and the MAC as the design variables and the objective function, respectively. The proposed GA-based evolutionary optimization method is validated through the numerical experiment with a rectangular plate, and its excellence is verified from the comparison with the cases using different modal correlation measures.

  16. Cross-modal decoupling in temporal attention.

    Science.gov (United States)

    Mühlberg, Stefanie; Oriolo, Giovanni; Soto-Faraco, Salvador

    2014-06-01

    Prior studies have repeatedly reported behavioural benefits to events occurring at attended, compared to unattended, points in time. It has been suggested that, as for spatial orienting, temporal orienting of attention spreads across sensory modalities in a synergistic fashion. However, the consequences of cross-modal temporal orienting of attention remain poorly understood. One challenge is that the passage of time leads to an increase in event predictability throughout a trial, thus making it difficult to interpret possible effects (or lack thereof). Here we used a design that avoids complete temporal predictability to investigate whether attending to a sensory modality (vision or touch) at a point in time confers beneficial access to events in the other, non-attended, sensory modality (touch or vision, respectively). In contrast to previous studies and to what happens with spatial attention, we found that events in one (unattended) modality do not automatically benefit from happening at the time point when another modality is expected. Instead, it seems that attention can be deployed in time with relative independence for different sensory modalities. Based on these findings, we argue that temporal orienting of attention can be cross-modally decoupled in order to flexibly react according to the environmental demands, and that the efficiency of this selective decoupling unfolds in time. © 2014 Federation of European Neuroscience Societies and John Wiley & Sons Ltd.

  17. History of Civil Engineering Modal Analysis

    DEFF Research Database (Denmark)

    Brincker, Rune

    2008-01-01

    techniques are available for civil engineering modal analysis. The testing of civil structures defers from the traditional modal testing in the sense, that very often it is difficult, or sometimes impossible, to artificially excite a large civil engineering structure. Also, many times, even though...

  18. Three-valued logics in modal logic

    NARCIS (Netherlands)

    Kooi, Barteld; Tamminga, Allard

    2013-01-01

    Every truth-functional three-valued propositional logic can be conservatively translated into the modal logic S5. We prove this claim constructively in two steps. First, we define a Translation Manual that converts any propositional formula of any three-valued logic into a modal formula. Second, we

  19. The Wigner distribution function in modal characterisation

    CSIR Research Space (South Africa)

    Mredlana, Prince

    2016-07-01

    Full Text Available function in modal characterisation P. MREDLANA1, D. NAIDOO1, C MAFUSIRE2, T. KRUGER2, A. DUDLEY1,3, A. FORBES1,3 1CSIR National Laser Centre, PO BOX 395, Pretoria 0001, South Africa. 2Department of Physics, Faculty of Natural and Agricultural..., the Wigner distribution of 𝑓 𝑥 is an integral of the correlation function 𝑓 𝑥 + 1 2 𝑥′ 𝑓 ∗ 𝑥 + 1 2 𝑥′ represented as: 𝑊𝑓 𝑥, 𝑒 = 𝑓 𝑥 + 1 2 𝑥′ 𝑓 ∗ 𝑥 + 1 2 𝑥′ 𝑒−𝑖𝑒𝑥′𝑑ð...

  20. World Input-Output Network.

    Directory of Open Access Journals (Sweden)

    Federica Cerina

    Full Text Available Production systems, traditionally analyzed as almost independent national systems, are increasingly connected on a global scale. Only recently becoming available, the World Input-Output Database (WIOD is one of the first efforts to construct the global multi-regional input-output (GMRIO tables. By viewing the world input-output system as an interdependent network where the nodes are the individual industries in different economies and the edges are the monetary goods flows between industries, we analyze respectively the global, regional, and local network properties of the so-called world input-output network (WION and document its evolution over time. At global level, we find that the industries are highly but asymmetrically connected, which implies that micro shocks can lead to macro fluctuations. At regional level, we find that the world production is still operated nationally or at most regionally as the communities detected are either individual economies or geographically well defined regions. Finally, at local level, for each industry we compare the network-based measures with the traditional methods of backward linkages. We find that the network-based measures such as PageRank centrality and community coreness measure can give valuable insights into identifying the key industries.

  1. Parameter setting and input reduction

    NARCIS (Netherlands)

    Evers, A.; van Kampen, N.J.|info:eu-repo/dai/nl/126439737

    2008-01-01

    The language acquisition procedure identifies certain properties of the target grammar before others. The evidence from the input is processed in a stepwise order. Section 1 equates that order and its typical effects with an order of parameter setting. The question is how the acquisition procedure

  2. Constituency Input into Budget Management.

    Science.gov (United States)

    Miller, Norman E.

    1995-01-01

    Presents techniques for ensuring constituency involvement in district- and site-level budget management. Outlines four models for securing constituent input and focuses on strategies to orchestrate the more complex model for staff and community participation. Two figures are included. (LMI)

  3. Remote input/output station

    CERN Multimedia

    1972-01-01

    A general view of the remote input/output station installed in building 112 (ISR) and used for submitting jobs to the CDC 6500 and 6600. The card reader on the left and the line printer on the right are operated by programmers on a self-service basis.

  4. Lithium inputs to subduction zones

    NARCIS (Netherlands)

    Bouman, C.; Elliott, T.R.; Vroon, P.Z.

    2004-01-01

    We have studied the sedimentary and basaltic inputs of lithium to subduction zones. Various sediments from DSDP and ODP drill cores in front of the Mariana, South Sandwich, Banda, East Sunda and Lesser Antilles island arcs have been analysed and show highly variable Li contents and δ

  5. Sensory Synergy as Environmental Input Integration

    Directory of Open Access Journals (Sweden)

    Fady eAlnajjar

    2015-01-01

    Full Text Available The development of a method to feed proper environmental inputs back to the central nervous system (CNS remains one of the challenges in achieving natural movement when part of the body is replaced with an artificial device. Muscle synergies are widely accepted as a biologically plausible interpretation of the neural dynamics between the CNS and the muscular system. Yet the sensorineural dynamics of environmental feedback to the CNS has not been investigated in detail. In this study, we address this issue by exploring the concept of sensory synergy. In contrast to muscle synergy, we hypothesize that sensory synergy plays an essential role in integrating the overall environmental inputs to provide low-dimensional information to the CNS. We assume that sensor synergy and muscle synergy communicate using these low-dimensional signals. To examine our hypothesis, we conducted posture control experiments involving lateral disturbance with 9 healthy participants. Proprioceptive information represented by the changes on muscle lengths were estimated by using the musculoskeletal model analysis software SIMM. Changes on muscles lengths were then used to compute sensory synergies. The experimental results indicate that the environmental inputs were translated into the two dimensional signals and used to move the upper limb to the desired position immediately after the lateral disturbance. Participants who showed high skill in posture control were found to be likely to have a strong correlation between sensory and muscle signaling as well as high coordination between the utilized sensory synergies. These results suggest the importance of integrating environmental inputs into suitable low-dimensional signals before providing them to the CNS. This mechanism should be essential when designing the prosthesis’ sensory system to make the controller simpler

  6. Sensory synergy as environmental input integration.

    Science.gov (United States)

    Alnajjar, Fady; Itkonen, Matti; Berenz, Vincent; Tournier, Maxime; Nagai, Chikara; Shimoda, Shingo

    2014-01-01

    The development of a method to feed proper environmental inputs back to the central nervous system (CNS) remains one of the challenges in achieving natural movement when part of the body is replaced with an artificial device. Muscle synergies are widely accepted as a biologically plausible interpretation of the neural dynamics between the CNS and the muscular system. Yet the sensorineural dynamics of environmental feedback to the CNS has not been investigated in detail. In this study, we address this issue by exploring the concept of sensory synergy. In contrast to muscle synergy, we hypothesize that sensory synergy plays an essential role in integrating the overall environmental inputs to provide low-dimensional information to the CNS. We assume that sensor synergy and muscle synergy communicate using these low-dimensional signals. To examine our hypothesis, we conducted posture control experiments involving lateral disturbance with nine healthy participants. Proprioceptive information represented by the changes on muscle lengths were estimated by using the musculoskeletal model analysis software SIMM. Changes on muscles lengths were then used to compute sensory synergies. The experimental results indicate that the environmental inputs were translated into the two dimensional signals and used to move the upper limb to the desired position immediately after the lateral disturbance. Participants who showed high skill in posture control were found to be likely to have a strong correlation between sensory and muscle signaling as well as high coordination between the utilized sensory synergies. These results suggest the importance of integrating environmental inputs into suitable low-dimensional signals before providing them to the CNS. This mechanism should be essential when designing the prosthesis' sensory system to make the controller simpler.

  7. The rapid distraction of attentional resources toward the source of incongruent stimulus input during multisensory conflict.

    Science.gov (United States)

    Donohue, Sarah E; Todisco, Alexandra E; Woldorff, Marty G

    2013-04-01

    Neuroimaging work on multisensory conflict suggests that the relevant modality receives enhanced processing in the face of incongruency. However, the degree of stimulus processing in the irrelevant modality and the temporal cascade of the attentional modulations in either the relevant or irrelevant modalities are unknown. Here, we employed an audiovisual conflict paradigm with a sensory probe in the task-irrelevant modality (vision) to gauge the attentional allocation to that modality. ERPs were recorded as participants attended to and discriminated spoken auditory letters while ignoring simultaneous bilateral visual letter stimuli that were either fully congruent, fully incongruent, or partially incongruent (one side incongruent, one congruent) with the auditory stimulation. Half of the audiovisual letter stimuli were followed 500-700 msec later by a bilateral visual probe stimulus. As expected, ERPs to the audiovisual stimuli showed an incongruency ERP effect (fully incongruent versus fully congruent) of an enhanced, centrally distributed, negative-polarity wave starting ∼250 msec. More critically here, the sensory ERP components to the visual probes were larger when they followed fully incongruent versus fully congruent multisensory stimuli, with these enhancements greatest on fully incongruent trials with the slowest RTs. In addition, on the slowest-response partially incongruent trials, the P2 sensory component to the visual probes was larger contralateral to the preceding incongruent visual stimulus. These data suggest that, in response to conflicting multisensory stimulus input, the initial cognitive effect is a capture of attention by the incongruent irrelevant-modality input, pulling neural processing resources toward that modality, resulting in rapid enhancement, rather than rapid suppression, of that input.

  8. Investigating gaze-controlled input in a cognitive selection test

    OpenAIRE

    Gayraud, Katja; Hasse, Catrin; Eißfeldt, Hinnerk; Pannasch, Sebastian

    2017-01-01

    In the field of aviation, there is a growing interest in developing more natural forms of interaction between operators and systems to enhance safety and efficiency. These efforts also include eye gaze as an input channel for human-machine interaction. The present study investigates the application of gaze-controlled input in a cognitive selection test called Eye Movement Conflict Detection Test. The test enables eye movements to be studied as an indicator for psychological test performance a...

  9. Modal analysis of a stiffened toroidal shell sector

    International Nuclear Information System (INIS)

    Cerreta, R.; Di Pietro, E.; Pizzuto, A.

    1987-01-01

    This paper presents the results of the modal analysis of a sector of the toroidal vacuum vessel of a new experimental machine for research in the field of controlled thermonuclear fusion (FTU - Frascati Tokamak Upgrade). The vacuum vessel, one of the most critical components of the experimental device, consist of 12 stainless steel toroidal sectors, and it is designed to withstand pulsed electromagnetic loads during operation. Results of the modal analysis of the stiffened toroidal shell sector are compared and discussed with regard to the experimental data. Theoretical eigenvalues and eigenvectors have been predicted by means of ABAQUS finite element code. Experimental analysis has been carried out on a full scale model and natural frequencies have been measured. Satisfactory agreement between experimental and theoretical eigenvalues has been found

  10. Conceptual structure within and between modalities

    Directory of Open Access Journals (Sweden)

    Katia eDilkina

    2013-01-01

    Full Text Available Current views of semantic memory share the assumption that conceptual representations are based on multi-modal experience, which activates distinct modality-specific brain regions. This proposition is widely accepted, yet little is known about how each modality contributes to conceptual knowledge and how the structure of this contribution varies across these multiple information sources. We used verbal feature lists, features from drawings and verbal co-occurrence statistics from latent semantic analysis to examine the informational structure in four domains of knowledge: perceptual, functional, encyclopedic and verbal. The goals of the analysis were three-fold: (1 to assess the structure within individual modalities; (2 to compare structures between modalities; and (3 to assess the degree to which concepts organize categorically or randomly.Our results indicated significant and unique structure in all four modalities: perceptually, concepts organize based on prominent features such as shape, size, color and parts; functionally, they group based on use and interaction; encyclopedically, they arrange based on commonality in location or behavior; and verbally, they group associatively or relationally. Visual/perceptual knowledge gives rise to the strongest hierarchical organization and is closest to classic taxonomic structure. Information is organized somewhat similarly in the perceptual and encyclopedic domains, which differs significantly from the structure in the functional and verbal domains. Notably, the verbal modality has the most unique organization, which is not at all categorical but also not random. The idiosyncrasy and complexity of conceptual structure across modalities begs the question of how all of these modality-specific experiences are fused together into coherent, multi-faceted yet unified concepts. Accordingly, both methodological and theoretical implications of the present findings are discussed.

  11. Extending Modal Transition Systems with Structured Labels

    DEFF Research Database (Denmark)

    Bauer, Sebastian S.; Juhl, Line; Larsen, Kim Guldstrand

    2012-01-01

    We introduce a novel formalism of label-structured modal transition systems that combines the classical may/must modalities on transitions with structured labels that represent quantitative aspects of the model. On the one hand, the specification formalism is general enough to include models like...... weighted modal transition systems and allows the system developers to employ more complex label refinement than in the previously studied theories. On the other hand, the formalism maintains the desirable properties required by any specification theory supporting compositional reasoning. In particular, we...

  12. Modeling of Temperature Effect on Modal Frequency of Concrete Beam Based on Field Monitoring Data

    Directory of Open Access Journals (Sweden)

    Wenchen Shan

    2018-01-01

    Full Text Available Temperature variation has been widely demonstrated to produce significant effect on modal frequencies that even exceed the effect of actual damage. In order to eliminate the temperature effect on modal frequency, an effective method is to construct quantitative models which accurately predict the modal frequency corresponding to temperature variation. In this paper, principal component analysis (PCA is conducted on the temperatures taken from all embedded thermocouples for extracting input parameters of regression models. Three regression-based numerical models using multiple linear regression (MLR, back-propagation neural network (BPNN, and support vector regression (SVR techniques are constructed to capture the relationships between modal frequencies and temperature distributions from measurements of a concrete beam during a period of forty days of monitoring. A comparison with respect to the performance of various optimally configured regression models has been performed on measurement data. Results indicate that the SVR exhibits a better reproduction and prediction capability than BPNN and MLR models for predicting the modal frequencies with respect to nonuniformly distributed temperatures. It is succeeded that temperature effects on modal frequencies can be effectively eliminated based on the optimally formulated SVR model.

  13. Using Response Surface Methods to Correlate the Modal Test of an Inflatable Test Article

    Science.gov (United States)

    Gupta, Anju

    2013-01-01

    This paper presents a practical application of response surface methods (RSM) to correlate a finite element model of a structural modal test. The test article is a quasi-cylindrical inflatable structure which primarily consists of a fabric weave, with an internal bladder and metallic bulkheads on either end. To mitigate model size, the fabric weave was simplified by representing it with shell elements. The task at hand is to represent the material behavior of the weave. The success of the model correlation is measured by comparing the four major modal frequencies of the analysis model to the four major modal frequencies of the test article. Given that only individual strap material properties were provided and material properties of the overall weave were not available, defining the material properties of the finite element model became very complex. First it was necessary to determine which material properties (modulus of elasticity in the hoop and longitudinal directions, shear modulus, Poisson's ratio, etc.) affected the modal frequencies. Then a Latin Hypercube of the parameter space was created to form an efficiently distributed finite case set. Each case was then analyzed with the results input into RSM. In the resulting response surface it was possible to see how each material parameter affected the modal frequencies of the analysis model. If the modal frequencies of the analysis model and its corresponding parameters match the test with acceptable accuracy, it can be said that the model correlation is successful.

  14. Impact of anthropogenic activities and natural inputs on ...

    African Journals Online (AJOL)

    The surface sediments and sea water interactions were studied in five different sites along the Egyptian Red Sea coast. There are commutative and correlative relations between these constituents, therefore, any alterations occur in the sediments and sea water will be directly reflected on the marine environment. Sixty-five ...

  15. Investigation of Apple Vibration Characteristics Using Finite Element Modal Analysis

    Directory of Open Access Journals (Sweden)

    R Mirzaei

    2013-02-01

    Full Text Available The most important quality indicator of fruits is the flesh firmness which is well correlated to their young’s modulus. In this research variation of vibration characteristics (shape modes, natural frequency of apple due to change of material characteristics (density, young's models, Poisson ratio and apple volume was investigated using Finite Element simulation. An image processing technique was used to obtain an unsymmetrical and non-spherical geometric model of apple. The exact three-dimensional shape of the fruit was created by determining the coordinates of apple surface and forming uneven rotational curvatures. Modal analysis with no boundary constraints has been applied. The first 20 Eigen frequencies and the corresponding mode shape were determined. Six rigid body modes possess zero resonant frequency which is related to the degree of freedom of a rigid body in space indicated the validity of finite element model. The modal analysis results showed that resonant frequency increased by increasing young's modulus of the fruit, while it decreased by increasing apple density. First mode torsion has a mean resonant frequency of 584 Hz. Variations of natural frequency due to change in young's modulus, density, and Poisson ratio were 80%, 11% and 4%, respectively. Coefficient of variation of resonant frequency in response to changing young's modulus was 2-3 times of that of density which shows the greatest effect of young modulus changes on natural frequency of fruits. Consequently with determination of fruits' natural frequency, their young modulus and firmness can be estimated.

  16. Input measurements in reprocessing plants

    International Nuclear Information System (INIS)

    Trincherini, P.R.; Facchetti, S.

    1980-01-01

    The aim of this work is to give a review of the methods and the problems encountered in measurements in 'input accountability tanks' of irradiated fuel treatment plants. This study was prompted by the conviction that more and more precise techniques and methods should be at the service of safeguards organizations and that ever greater efforts should be directed towards promoting knowledge of them among operators and all those general area of interest includes the nuclear fuel cycle. The overall intent is to show the necessity of selecting methods which produce measurements which are not only more precise but are absolutely reliable both for routine plant operation and for safety checks in the input area. A description and a critical evaluation of the most common physical and chemical methods are provided, together with an estimate of the precision and accuracy obtained in real operating conditions

  17. Experimental and Computational Modal Analyses for Launch Vehicle Models considering Liquid Propellant and Flange Joints

    Directory of Open Access Journals (Sweden)

    Chang-Hoon Sim

    2018-01-01

    Full Text Available In this research, modal tests and analyses are performed for a simplified and scaled first-stage model of a space launch vehicle using liquid propellant. This study aims to establish finite element modeling techniques for computational modal analyses by considering the liquid propellant and flange joints of launch vehicles. The modal tests measure the natural frequencies and mode shapes in the first and second lateral bending modes. As the liquid filling ratio increases, the measured frequencies decrease. In addition, as the number of flange joints increases, the measured natural frequencies increase. Computational modal analyses using the finite element method are conducted. The liquid is modeled by the virtual mass method, and the flange joints are modeled using one-dimensional spring elements along with the node-to-node connection. Comparison of the modal test results and predicted natural frequencies shows good or moderate agreement. The correlation between the modal tests and analyses establishes finite element modeling techniques for modeling the liquid propellant and flange joints of space launch vehicles.

  18. The modality effect and echoic persistence.

    Science.gov (United States)

    Watkins, O C; Watkins, M J

    1980-09-01

    The modality effect refers to the higher level of recall of the last few items of a list when presentation is auditory as opposed to visual. It is usually attributed to echoic memory. The effect may be sharply reduced by an ostensibly irrelevant auditory item appended to the end of the list. Previous research suggests that this "suffix effect" arises only when the suffix item occurs within 2 sec of the last list item. This finding strengthens the widely held assumption that echoic information decays within 2 sec, and has led to the assumption that if echoic information is to be useful in serial recall it must first be encoded into a more durable modality-independent form. Both assumptions conflict with the research reported here. The first two experiments demonstrate substantial suffix effects with suffix delays of 2 and 4 sec, indicating that echoic information lasts at least 4 sec. This finding implies that echoic information may aid recall directly, an implication that was supported in Experiments 3 and 4. In Experiment 3 serial recall was interrupted with a brief distractor task. The modality effect was smaller when this task was auditory than when it was visual, suggesting that echoic information was still available immediately prior to recency recall. In Experiment 4 list presentation was broken by a 4-sec pause; the modalities of the list halves were combined factorially. Interest focused on the recency positions of the first half. A modality effect was found at these positions when the second half was visual but not when it was auditory. This is contrary to the hypothesis that echoic information is encoded before recall, but is consistent with the hypothesis that echoic information is encoded before recall, but is consistent with the alternative hypothesis that echoic information is used directly at recall. The final two experiments concern the modality effect found when a delay is interpolated between list presentation and recall. Experiment 5 showed that

  19. DICOM versus HL7 for modality interfacing

    OpenAIRE

    Oosterwijk, Herman

    1998-01-01

    Digital modalities such as CT, MRI, Ultrasound and Computerized Radiography systems, generating softcopy images to be used by a Picture Archiving and Communication System (PACS), need to identify the images properly in order to retrieve and manage them. In many cases, a technologist re-enters patient demographic and study related information at the modality, even although it is usually already present somewhere in the hospital Information System (IS). In order to achieve a higher level of eff...

  20. Models of galaxies - The modal approach

    International Nuclear Information System (INIS)

    Lin, C.C.; Lowe, S.A.

    1990-01-01

    The general viability of the modal approach to the spiral structure in normal spirals and the barlike structure in certain barred spirals is discussed. The usefulness of the modal approach in the construction of models of such galaxies is examined, emphasizing the adoption of a model appropriate to observational data for both the spiral structure of a galaxy and its basic mass distribution. 44 refs

  1. Eigenvectors phase correction in inverse modal problem

    Science.gov (United States)

    Qiao, Guandong; Rahmatalla, Salam

    2017-12-01

    The solution of the inverse modal problem for the spatial parameters of mechanical and structural systems is heavily dependent on the quality of the modal parameters obtained from the experiments. While experimental and environmental noises will always exist during modal testing, the resulting modal parameters are expected to be corrupted with different levels of noise. A novel methodology is presented in this work to mitigate the errors in the eigenvectors when solving the inverse modal problem for the spatial parameters. The phases of the eigenvector component were utilized as design variables within an optimization problem that minimizes the difference between the calculated and experimental transfer functions. The equation of motion in terms of the modal and spatial parameters was used as a constraint in the optimization problem. Constraints that reserve the positive and semi-positive definiteness and the inter-connectivity of the spatial matrices were implemented using semi-definite programming. Numerical examples utilizing noisy eigenvectors with augmented Gaussian white noise of 1%, 5%, and 10% were used to demonstrate the efficacy of the proposed method. The results showed that the proposed method is superior when compared with a known method in the literature.

  2. Applications of the Automated SMAC Modal Parameter Extraction Package

    International Nuclear Information System (INIS)

    MAYES, RANDALL L.; DORRELL, LARRY R.; KLENKE, SCOTT E.

    1999-01-01

    An algorithm known as SMAC (Synthesize Modes And Correlate), based on principles of modal filtering, has been in development for a few years. The new capabilities of the automated version are demonstrated on test data from a complex shell/payload system. Examples of extractions from impact and shaker data are shown. The automated algorithm extracts 30 to 50 modes in the bandwidth from each column of the frequency response function matrix. Examples of the synthesized Mode Indicator Functions (MIFs) compared with the actual MIFs show the accuracy of the technique. A data set for one input and 170 accelerometer outputs can typically be reduced in an hour. Application to a test with some complex modes is also demonstrated

  3. Design of optical fibres with advanced modal control properties

    DEFF Research Database (Denmark)

    Muliar, Olena

    this goal, an interferometric-based fibre characterisation technique, known as a cross-correlated (C 2 ) imaging, was explored. An alternative modal reconstruction approach by 2D Fourier transform was presented, that allowed to extract intensity and phase distributions of the fibre mode from a single...... interferogram, acquired by a camera at a specific time delay. Aforementioned reconstruction technique was implemented for a flexible C 2 imaging, which was realised by an application of a tunable and highly flexible light source. Current configuration of the C 2 set-up gave an opportunity to investigate...... an influence of a spectral shape and bandwidth on a temporal resolution of the method and to form the input spectrum according to experimental requirements of the fibre design. A demonstration of the flexible C 2 imaging was performed by a characterisation of a step-index fibre (SMF28) and a distributed mode...

  4. Knowledge Engineering Aspects of Affective Bi-Modal Educational Applications

    Science.gov (United States)

    Alepis, Efthymios; Virvou, Maria; Kabassi, Katerina

    This paper analyses the knowledge and software engineering aspects of educational applications that provide affective bi-modal human-computer interaction. For this purpose, a system that provides affective interaction based on evidence from two different modes has been developed. More specifically, the system's inferences about students' emotions are based on user input evidence from the keyboard and the microphone. Evidence from these two modes is combined by a user modelling component that incorporates user stereotypes as well as a multi criteria decision making theory. The mechanism that integrates the inferences from the two modes has been based on the results of two empirical studies that were conducted in the context of knowledge engineering of the system. The evaluation of the developed system showed significant improvements in the recognition of the emotional states of users.

  5. Design and optimization of a modal- independent linear ultrasonic motor.

    Science.gov (United States)

    Zhou, Shengli; Yao, Zhiyuan

    2014-03-01

    To simplify the design of the linear ultrasonic motor (LUSM) and improve its output performance, a method of modal decoupling for LUSMs is proposed in this paper. The specific embodiment of this method is decoupling of the traditional LUSM stator's complex vibration into two simple vibrations, with each vibration implemented by one vibrator. Because the two vibrators are designed independently, their frequencies can be tuned independently and frequency consistency is easy to achieve. Thus, the method can simplify the design of the LUSM. Based on this method, a prototype modal- independent LUSM is designed and fabricated. The motor reaches its maximum thrust force of 47 N, maximum unloaded speed of 0.43 m/s, and maximum power of 7.85 W at applied voltage of 200 Vpp. The motor's structure is then optimized by controlling the difference between the two vibrators' resonance frequencies to reach larger output speed, thrust, and power. The optimized results show that when the frequency difference is 73 Hz, the output force, speed, and power reach their maximum values. At the input voltage of 200 Vpp, the motor reaches its maximum thrust force of 64.2 N, maximum unloaded speed of 0.76 m/s, maximum power of 17.4 W, maximum thrust-weight ratio of 23.7, and maximum efficiency of 39.6%.

  6. Mechanics of inter-modal tunneling in nonlinear waveguides

    Science.gov (United States)

    Jiao, Weijian; Gonella, Stefano

    2018-02-01

    In this article, we investigate the mechanics of nonlinearly induced inter-modal energy tunneling between flexurally-dominated and axially-dominated modes in phononic waveguides. Special attention is devoted to elucidating the role played by the coupling between axial and flexural degrees of freedom in the determination of the available mode hopping conditions and the associated mechanisms of deformation. Waveguides offer an ideal test bed to investigate the mechanics of nonlinear energy tunneling, due to the fact that they naturally feature, even at low frequencies, families of modes (flexural and axial) that are intrinsically characterized by extreme complementarity. Moreover, thanks to their geometric simplicity, their behavior can be explained by resorting to intuitive structural mechanics models that effectively capture the dichotomy and interplay between flexural and axial mechanisms. After having delineated the fundamental mechanics of flexural-to-axial hopping using the benchmark example of a homogeneous structure, we adapt the analysis to the case of periodic waveguides, in which the complex dispersive behavior due to periodicity results in additional richness of mode hopping mechanisms. We finally extend the analysis to periodic waveguides with internal resonators, in which the availability of locally-resonant bandgaps implies the possibility to activate the resonators even at relatively low frequencies, thus increasing the degree of modal complementarity that is available in the acoustic range. In this context, inter-modal tunneling provides an unprecedented mechanism to transfer conspicuous packets of energy to the resonating microstructure.

  7. Mixed-Modality Stimulation to Evoke Two Modalities Simultaneously in One Channel for Electrocutaneous Sensory Feedback.

    Science.gov (United States)

    Choi, Kyunghwan; Kim, Pyungkang; Kim, Kyung-Soo; Kim, Soohyun

    2017-12-01

    One of the long-standing challenges in upper limb prosthetics is restoring the sensory feedback that is missing due to amputation. Two approaches have previously been presented to provide various types of sensory information to users, namely, multi-modality sensory feedback and using an array of single-modality stimulators. However, the feedback systems used in these approaches were too bulky to be embedded in prosthesis sockets. In this paper, we propose an electrocutaneous sensory feedback method that is capable of conveying two modalities simultaneously with only one electrode. The stimulation method, which we call mixed-modality stimulation, utilizes the phenomenon in which the superposition of two electric pulse trains of different frequencies is able to evoke two different modalities (i.e., pressure and tapping) at the same time. We conducted psychophysical experiments in which healthy subjects were required to recognize the intensity of pressure or the frequency of tapping from mixed-modality or two-channel stimulations. The results demonstrated that the subjects were able to discriminate the features of the two modalities in one electrode during mixed-modality stimulation and that the accuracies of successful recognitions (mean ± standard deviation) for the two feedback variables were 84.3 ± 7% for mixed-modality stimulation and 89.5 ± 6% for two-channel dual-modality stimulation, showing no statistically significant difference. Therefore, mixed-modality stimulation is an attractive method for modulating two modalities independently with only one electrode, and it could be used for implementing a compact sensory feedback system that is able to provide two different types of sensory information from prosthetics.

  8. Recurrent activity in higher order, modality non-specific brain regions

    DEFF Research Database (Denmark)

    Lou, Hans Olav Christensen; Joensson, Morten; Biermann-Ruben, Katja

    2011-01-01

    It has been proposed that the workings of the brain are mainly intrinsically generated recurrent neuronal activity, with sensory inputs as modifiers of such activity in both sensory and higher order modality non-specific regions. This is supported by the demonstration of recurrent neuronal activity...... in the visual system as a response to visual stimulation. In contrast recurrent activity has never been demonstrated before in higher order modality non-specific regions. Using magneto-encephalography and Granger causality analysis, we tested in a paralimbic network the hypothesis that stimulation may enhance...... causal recurrent interaction between higher-order, modality non-specific regions. The network includes anterior cingulate/medial prefrontal and posterior cingulate/medial parietal cortices together with pulvinar thalami, a network known to be effective in autobiographic memory retrieval and self...

  9. Modal analysis of pre and post impacted nano composite laminates

    Directory of Open Access Journals (Sweden)

    R. Velmurugan

    Full Text Available Modal analysis is carried out on pre and post impacted nano composite laminates. The laminates are prepared using 3, 5 and 8 layers of 610gsm glass woven roving mats(WRM with epoxy resin and montmorillonite(MMT clay content is varied from 1% to 5%. Impulse hammer technique is used to find natural frequency and damping factor of laminates. Medium velocity impact tests are conducted by using a gas gun. The vibration responses of natural frequency and damping factor are obtained and are studied for laminates with all edges clamped boundary conditions. Results show considerable improvement in natural frequency and damping factor due to nano clay addition. It is also seen that the nano clay controls the delamination due to impact loading.

  10. Metaphysical Modality, Modality of Predicate and the Theory of "Decisive Necessity”

    Directory of Open Access Journals (Sweden)

    L. Nabavi

    2010-01-01

    Full Text Available Aristotle in the Organon (1949: 9,30 a ,15-19 explicitly states that in a categorical syllogism when the minor premise is absolute (without modality operator and the major is necessary, the conclusion will be necessary too. This Aristotle's view has been the source of many conflicts and disputes in the history of logic. The famous logicians and historians of logic in the twentieth century as "Nicholas Rescher" and "Becker" believe that Aristotle's view is justifiable and defensible (at least compared to the first figure only if, the modality of major premise is considered as the property of predicate (modality de re. Today, we know very well that the modality of predicate is closely linked to Metaphysical and philosophical Modality. “Shihab al-Din al- Suhrawardi” in the theory of "Decisive (Battateh Necessity” by accepting this base, explicitly states that, in the beginning, the modality must be mentioned as a part of the predicate and then the modality of relation or copula is summarized and reduced to necessity. The modern formalization of the most important part of this theory is as follows: ("x (àAx É à Bx º ("x □ (àAx É à BxThis paper discusses the historical overview of the metaphysical modality firstly and then shows that the theory of "Decisive Necessity” is true and justified in a model of modal logic with equivalent accessibility relation and homogeneous possible world view (fixed domain.

  11. Modality-specific effects on crosstalk in task switching: evidence from modality compatibility using bimodal stimulation.

    Science.gov (United States)

    Stephan, Denise Nadine; Koch, Iring

    2016-11-01

    The present study was aimed at examining modality-specific influences in task switching. To this end, participants switched either between modality compatible tasks (auditory-vocal and visual-manual) or incompatible spatial discrimination tasks (auditory-manual and visual-vocal). In addition, auditory and visual stimuli were presented simultaneously (i.e., bimodally) in each trial, so that selective attention was required to process the task-relevant stimulus. The inclusion of bimodal stimuli enabled us to assess congruence effects as a converging measure of increased between-task interference. The tasks followed a pre-instructed sequence of double alternations (AABB), so that no explicit task cues were required. The results show that switching between two modality incompatible tasks increases both switch costs and congruence effects compared to switching between two modality compatible tasks. The finding of increased congruence effects in modality incompatible tasks supports our explanation in terms of ideomotor "backward" linkages between anticipated response effects and the stimuli that called for this response in the first place. According to this generalized ideomotor idea, the modality match between response effects and stimuli would prime selection of a response in the compatible modality. This priming would cause increased difficulties to ignore the competing stimulus and hence increases the congruence effect. Moreover, performance would be hindered when switching between modality incompatible tasks and facilitated when switching between modality compatible tasks.

  12. Neural Mechanisms Underlying Cross-Modal Phonetic Encoding.

    Science.gov (United States)

    Shahin, Antoine J; Backer, Kristina C; Rosenblum, Lawrence D; Kerlin, Jess R

    2018-02-14

    Audiovisual (AV) integration is essential for speech comprehension, especially in adverse listening situations. Divergent, but not mutually exclusive, theories have been proposed to explain the neural mechanisms underlying AV integration. One theory advocates that this process occurs via interactions between the auditory and visual cortices, as opposed to fusion of AV percepts in a multisensory integrator. Building upon this idea, we proposed that AV integration in spoken language reflects visually induced weighting of phonetic representations at the auditory cortex. EEG was recorded while male and female human subjects watched and listened to videos of a speaker uttering consonant vowel (CV) syllables /ba/ and /fa/, presented in Auditory-only, AV congruent or incongruent contexts. Subjects reported whether they heard /ba/ or /fa/. We hypothesized that vision alters phonetic encoding by dynamically weighting which phonetic representation in the auditory cortex is strengthened or weakened. That is, when subjects are presented with visual /fa/ and acoustic /ba/ and hear /fa/ ( illusion-fa ), the visual input strengthens the weighting of the phone /f/ representation. When subjects are presented with visual /ba/ and acoustic /fa/ and hear /ba/ ( illusion-ba ), the visual input weakens the weighting of the phone /f/ representation. Indeed, we found an enlarged N1 auditory evoked potential when subjects perceived illusion-ba , and a reduced N1 when they perceived illusion-fa , mirroring the N1 behavior for /ba/ and /fa/ in Auditory-only settings. These effects were especially pronounced in individuals with more robust illusory perception. These findings provide evidence that visual speech modifies phonetic encoding at the auditory cortex. SIGNIFICANCE STATEMENT The current study presents evidence that audiovisual integration in spoken language occurs when one modality (vision) acts on representations of a second modality (audition). Using the McGurk illusion, we show

  13. Different patterns of modality dominance across development.

    Science.gov (United States)

    Barnhart, Wesley R; Rivera, Samuel; Robinson, Christopher W

    2018-01-01

    The present study sought to better understand how children, young adults, and older adults attend and respond to multisensory information. In Experiment 1, young adults were presented with two spoken words, two pictures, or two word-picture pairings and they had to determine if the two stimuli/pairings were exactly the same or different. Pairing the words and pictures together slowed down visual but not auditory response times and delayed the latency of first fixations, both of which are consistent with a proposed mechanism underlying auditory dominance. Experiment 2 examined the development of modality dominance in children, young adults, and older adults. Cross-modal presentation attenuated visual accuracy and slowed down visual response times in children, whereas older adults showed the opposite pattern, with cross-modal presentation attenuating auditory accuracy and slowing down auditory response times. Cross-modal presentation also delayed first fixations in children and young adults. Mechanisms underlying modality dominance and multisensory processing are discussed. Copyright © 2017 Elsevier B.V. All rights reserved.

  14. The metaphysics of quantum mechanics: Modal interpretations

    Science.gov (United States)

    Gluck, Stuart Murray

    2004-11-01

    This dissertation begins with the argument that a preferred way of doing metaphysics is through philosophy of physics. An understanding of quantum physics is vital to answering questions such as: What counts as an individual object in physical ontology? Is the universe fundamentally indeterministic? Are indiscernibles identical? This study explores how the various modal interpretations of quantum mechanics answer these sorts of questions; modal accounts are one of the two classes of interpretations along with so-called collapse accounts. This study suggests a new alternative within the class of modal views that yields a more plausible ontology, one in which the Principle of the Identity of Indisceribles is necessarily true. Next, it shows that modal interpretations can consistently deny that the universe must be fundamentally indeterministic so long as they accept certain other metaphysical commitments: either a perfect initial distribution of states in the universe or some form of primitive dispositional properties. Finally, the study sketches out a future research project for modal interpretations based on developing quantified quantum logic.

  15. Stochastic weather inputs for improved urban water demand forecasting: application of nonlinear input variable selection and machine learning methods

    Science.gov (United States)

    Quilty, J.; Adamowski, J. F.

    2015-12-01

    Urban water supply systems are often stressed during seasonal outdoor water use as water demands related to the climate are variable in nature making it difficult to optimize the operation of the water supply system. Urban water demand forecasts (UWD) failing to include meteorological conditions as inputs to the forecast model may produce poor forecasts as they cannot account for the increase/decrease in demand related to meteorological conditions. Meteorological records stochastically simulated into the future can be used as inputs to data-driven UWD forecasts generally resulting in improved forecast accuracy. This study aims to produce data-driven UWD forecasts for two different Canadian water utilities (Montreal and Victoria) using machine learning methods by first selecting historical UWD and meteorological records derived from a stochastic weather generator using nonlinear input variable selection. The nonlinear input variable selection methods considered in this work are derived from the concept of conditional mutual information, a nonlinear dependency measure based on (multivariate) probability density functions and accounts for relevancy, conditional relevancy, and redundancy from a potential set of input variables. The results of our study indicate that stochastic weather inputs can improve UWD forecast accuracy for the two sites considered in this work. Nonlinear input variable selection is suggested as a means to identify which meteorological conditions should be utilized in the forecast.

  16. Input Variability Facilitates Unguided Subcategory Learning in Adults

    Science.gov (United States)

    Eidsvåg, Sunniva Sørhus; Austad, Margit; Plante, Elena; Asbjørnsen, Arve E.

    2015-01-01

    Purpose: This experiment investigated whether input variability would affect initial learning of noun gender subcategories in an unfamiliar, natural language (Russian), as it is known to assist learning of other grammatical forms. Method: Forty adults (20 men, 20 women) were familiarized with examples of masculine and feminine Russian words. Half…

  17. Limiting labor input is an overall prerequisite for sustainability

    DEFF Research Database (Denmark)

    Nørgaard, Jørgen

    2006-01-01

    The purpose of the paper is to show by a simple, aggregate, descriptive model, how the importance of labor input to the production sector has to be revised in a future aiming at sustainable development. Despite substantial technological potentials for more eco-efficient utilization of nature...

  18. Cross-modal links among vision, audition, and touch in complex environments.

    Science.gov (United States)

    Ferris, Thomas K; Sarter, Nadine B

    2008-02-01

    This study sought to determine whether performance effects of cross-modal spatial links that were observed in earlier laboratory studies scale to more complex environments and need to be considered in multimodal interface design. It also revisits the unresolved issue of cross-modal cuing asymmetries. Previous laboratory studies employing simple cues, tasks, and/or targets have demonstrated that the efficiency of processing visual, auditory, and tactile stimuli is affected by the modality, lateralization, and timing of surrounding cues. Very few studies have investigated these cross-modal constraints in the context of more complex environments to determine whether they scale and how complexity affects the nature of cross-modal cuing asymmetries. Amicroworld simulation of battlefield operations with a complex task set and meaningful visual, auditory, and tactile stimuli was used to investigate cuing effects for all cross-modal pairings. Significant asymmetric performance effects of cross-modal spatial links were observed. Auditory cues shortened response latencies for collocated visual targets but visual cues did not do the same for collocated auditory targets. Responses to contralateral (rather than ipsilateral) targets were faster for tactually cued auditory targets and each visual-tactile cue-target combination, suggesting an inhibition-of-return effect. The spatial relationships between multimodal cues and targets significantly affect target response times in complex environments. The performance effects of cross-modal links and the observed cross-modal cuing asymmetries need to be examined in more detail and considered in future interface design. The findings from this study have implications for the design of multimodal and adaptive interfaces and for supporting attention management in complex, data-rich domains.

  19. Automated Modal Parameter Estimation for Operational Modal Analysis of Large Systems

    DEFF Research Database (Denmark)

    Andersen, Palle; Brincker, Rune; Goursat, Maurice

    2007-01-01

    In this paper the problems of doing automatic modal parameter extraction and how to account for large number of data to process are considered. Two different approaches for obtaining the modal parameters automatically using OMA are presented: The Frequency Domain Decomposition (FDD) technique and...

  20. Affirmation Modality in Bulgarian, Macedonian and Serbian

    Directory of Open Access Journals (Sweden)

    Marcin Grygiel

    2015-06-01

    Full Text Available Affirmation Modality in Bulgarian, Macedonian and Serbian In the case of affirmation modality the speakers transform their utterances by stressing or attributing a positive value as an additional component added to the semantic structure of a proposition. This type of affirmative polarization is triggered in opposition to negation or hypothetically negative contexts. The goal of the present paper is twofold: on the one hand to compare and contrast affirmative periphrastic constructions in Bulgarian, Macedonian and Serbian and, on the other hand, to ascertain what these constructions reveal regarding the organization of grammatical categories in general and the status of affirmation modality as a coherent and homogenous category with a linguistic validity.

  1. Complete proof systems for weighted modal logic

    DEFF Research Database (Denmark)

    Larsen, Kim G.; Mardare, Radu

    2014-01-01

    (WML) is a multi-modal logic that expresses qualitative and quantitative properties of WTSs. While WML has been studied in various contexts and for various application domains, no proof system has been developed for it. In this paper we solve this open problem and propose both weak-complete and strong......The weighted transition systems (WTS) considered in this paper are transition systems having both states and transitions labeled with real numbers: the state labels denote quantitative resources, while the transition labels denote costs of transitions in terms of resources. Weighted Modal Logic....... This work emphasizes a series of similarities between WML and the probabilistic/stochastic modal logics for Markov processes and Harsanyi type spaces, such as the use of particular infinitary rules to guarantee the strong-completeness....

  2. Comparison of particle-radiation-therapy modalities

    International Nuclear Information System (INIS)

    Fairchild, R.G.; Bond, V.P.

    1981-01-01

    The characteristics of dose distribution, beam alignment, and radiobiological advantages accorded to high LET radiation were reviewed and compared for various particle beam radiotherapeutic modalities (neutron, Auger electrons, p, π - , He, C, Ne, and Ar ions). Merit factors were evaluated on the basis of effective dose to tumor relative to normal tissue, linear energy transfer (LET), and dose localization, at depths of 1, 4, and 10 cm. In general, it was found that neutron capture therapy using an epithermal neutron beam provided the best merit factors available for depths up to 8 cm. The position of fast neutron therapy on the Merit Factor Tables was consistently lower than that of other particle modalities, and above only 60 Co. The largest body of clinical data exists for fast neutron therapy; results are considered by some to be encouraging. It then follows that if benefits with fast neutron therapy are real, additional gains are within reach with other modalities

  3. Tumour Debulking for Esophageal Cancer - Thermal Modalities

    Directory of Open Access Journals (Sweden)

    David Fleischer

    1992-01-01

    Full Text Available Esophageal cancer usually is discovered at a late stage and curative therapy seldom is possible. The prognosis is poor and most therapy is palliative. Endoscopic therapy commonly is employed; two common treatments involve thermal modalities. The Nd:YAG laser has been employed for 10 years and is effective in relieving obstruction in approximately 90% of cases. Re-ohstruction usually occurs in two to three months and repeat treatment may be necessary. Limitations to laser use include the fact that equipment is expensive and there are technical restrictions. An alternative thermal modality is the bipolar coagulation tumour probe which employs bipolar electrocoagulation. It is less expensive and, if the tumour is circumferential, tends to be easier to use. (It should not be used if the cancer is noncircumferential. The advantages and limitations of each modality are addressed.

  4. Complex harmonic modal analysis of rotor systems

    International Nuclear Information System (INIS)

    Han, Dong Ju

    2015-01-01

    Complex harmonic analysis for rotor systems has been proposed from the strict complex modal analysis based upon Floquet theory. In this process the harmonic balance method is adopted, effectively associated with conventional eigenvalue analysis. Also, the harmonic coefficients equivalent to dFRFs in harmonic mode has been derived in practice. The modes are classified from identifying the modal characteristics, and the adaptation of harmonic balance method has been proven by comparing the results of the stability analyses from Floque theory and the eigen analysis. The modal features of each critical speed are depicted in quantitatively and qualitatively by showing that the strengths of each component of the harmonic coefficients are estimated from the order of magnitude analysis according to their harmonic patterns. This effectiveness has been verified by comparing with the numerical solutions

  5. Free-free and fixed base modal survey tests of the Space Station Common Module Prototype

    Science.gov (United States)

    Driskill, T. C.; Anderson, J. B.; Coleman, A. D.

    1992-01-01

    This paper describes the testing aspects and the problems encountered during the free-free and fixed base modal surveys completed on the original Space Station Common Module Prototype (CMP). The CMP is a 40-ft long by 14.5-ft diameter 'waffle-grid' cylinder built by the Boeing Company and housed at the Marshall Space Flight Center (MSFC) near Huntsville, AL. The CMP modal survey tests were conducted at MSFC by the Dynamics Test Branch. The free-free modal survey tests (June '90 to Sept. '90) included interface verification tests (IFVT), often referred to as impedance measurements, mass-additive testing and linearity studies. The fixed base modal survey tests (Feb. '91 to April '91), including linearity studies, were conducted in a fixture designed to constrain the CMP in 7 total degrees-of-freedom at five trunnion interfaces (two primary, two secondary, and the keel). The fixture also incorporated an airbag off-load system designed to alleviate the non-linear effects of friction in the primary and secondary trunnion interfaces. Numerous test configurations were performed with the objective of providing a modal data base for evaluating the various testing methodologies to verify dynamic finite element models used for input to coupled load analysis.

  6. Artificial Vision, New Visual Modalities and Neuroadaptation

    Directory of Open Access Journals (Sweden)

    Hilmi Or

    2012-01-01

    Full Text Available To study the descriptions from which artificial vision derives, to explore the new visual modalities resulting from eye surgeries and diseases, and to gain awareness of the use of machine vision systems for both enhancement of visual perception and better understanding of neuroadaptation. Science could not define until today what vision is. However, some optical-based systems and definitions have been established considering some factors for the formation of seeing. The best known system includes Gabor filter and Gabor patch which work on edge perception, describing the visual perception in the best known way. These systems are used today in industry and technology of machines, robots and computers to provide their "seeing". These definitions are used beyond the machinery in humans for neuroadaptation in new visual modalities after some eye surgeries or to improve the quality of some already known visual modalities. Beside this, “the blindsight” -which was not known to exist until 35 years ago - can be stimulated with visual exercises. Gabor system is a description of visual perception definable in machine vision as well as in human visual perception. This system is used today in robotic vision. There are new visual modalities which arise after some eye surgeries or with the use of some visual optical devices. Also, blindsight is a different visual modality starting to be defined even though the exact etiology is not known. In all the new visual modalities, new vision stimulating therapies using the Gabor systems can be applied. (Turk J Oph thal mol 2012; 42: 61-5

  7. Chemical sensors are hybrid-input memristors

    Science.gov (United States)

    Sysoev, V. I.; Arkhipov, V. E.; Okotrub, A. V.; Pershin, Y. V.

    2018-04-01

    Memristors are two-terminal electronic devices whose resistance depends on the history of input signal (voltage or current). Here we demonstrate that the chemical gas sensors can be considered as memristors with a generalized (hybrid) input, namely, with the input consisting of the voltage, analyte concentrations and applied temperature. The concept of hybrid-input memristors is demonstrated experimentally using a single-walled carbon nanotubes chemical sensor. It is shown that with respect to the hybrid input, the sensor exhibits some features common with memristors such as the hysteretic input-output characteristics. This different perspective on chemical gas sensors may open new possibilities for smart sensor applications.

  8. Sensory modality specificity of neural activity related to memory in visual cortex.

    Science.gov (United States)

    Gibson, J R; Maunsell, J H

    1997-09-01

    Previous studies have shown that when monkeys perform a delayed match-to-sample (DMS) task, some neurons in inferotemporal visual cortex are activated selectively during the delay period when the animal must remember particular visual stimuli. This selective delay activity may be involved in short-term memory. It does not depend on visual stimulation: both auditory and tactile stimuli can trigger selective delay activity in inferotemporal cortex when animals expect to respond to visual stimuli in a DMS task. We have examined the overall modality specificity of delay period activity using a variety of auditory/visual cross-modal and unimodal DMS tasks. The cross-modal DMS tasks involved making specific long-term memory associations between visual and auditory stimuli, whereas the unimodal DMS tasks were standard identity matching tasks. Delay activity existed in auditory/visual cross-modal DMS tasks whether the animal anticipated responding to visual or auditory stimuli. No evidence of selective delay period activation was seen in a purely auditory DMS task. Delay-selective cells were relatively common in one animal where they constituted up to 53% neurons tested with a given task. This was only the case for up to 9% of cells in a second animal. In the first animal, a specific long-term memory representation for learned cross-modal associations was observed in delay activity, indicating that this type of representation need not be purely visual. Furthermore, in this same animal, delay activity in one cross-modal task, an auditory-to-visual task, predicted correct and incorrect responses. These results suggest that neurons in inferotemporal cortex contribute to abstract memory representations that can be activated by input from other sensory modalities, but these representations are specific to visual behaviors.

  9. Established rheumatoid arthritis - new imaging modalities

    DEFF Research Database (Denmark)

    McQueen, Fiona M; Østergaard, Mikkel

    2007-01-01

    in real-time and facilitates diagnostic and therapeutic interventions such as joint aspiration and injection. Exciting experimental modalities are also being developed with the potential to provide not just morphological but functional imaging. Techniques such as positron emission tomography (PET......) and high-resolution computerized tomography. Erosions are very clearly depicted using these modalities and MRI also allows imaging of soft tissues with assessment of joint inflammation. High-resolution ultrasound is a convenient clinical technique for the assessment of erosions, synovitis and tenosynovitis...

  10. Nonoperative modalities to treat symptomatic cervical spondylosis.

    LENUS (Irish Health Repository)

    Hirpara, Kieran Michael

    2012-01-01

    Cervical spondylosis is a common and disabling condition. It is generally felt that the initial management should be nonoperative, and these modalities include physiotherapy, analgesia and selective nerve root injections. Surgery should be reserved for moderate to severe myelopathy patients who have failed a period of conservative treatment and patients whose symptoms are not adequately controlled by nonoperative means. A review of the literature supporting various modalities of conservative management is presented, and it is concluded that although effective, nonoperative treatment is labour intensive, requiring regular review and careful selection of medications and physical therapy on a case by case basis.

  11. Dorsal and ventral streams across sensory modalities

    Institute of Scientific and Technical Information of China (English)

    Anna Sedda; Federica Scarpina

    2012-01-01

    In this review,we describe the current models of dorsal and ventral streams in vision,audition and touch.Available theories take their first steps from the model of Milner and Goodale,which was developed to explain how human actions can be efficiently carried out using visual information.Since then,similar concepts have also been applied to other sensory modalities.We propose that advances in the knowledge of brain functioning can be achieved through models explaining action and perception patterns independently from sensory modalities.

  12. Combined modality treatment with radiotherapy and chemotherapy

    International Nuclear Information System (INIS)

    Tannock, I.F.; Toronto Univ., ON

    1989-01-01

    The present paper discusses some of the methodological issues which can confound the interpretation of clinical trials of combined modality treatment. It reviews some of the larger randomized trials which have evaluated combined modality treatment in cancers of the head and neck, lung, gastrointestinal tract and bladder. It concludes that adequate trials have yet to be performed in many of thses sites, but that at present, evidence for long-term benefit from adjunctivechemotherapy is meagre. Finally, it suggests some possible mechanisms which might heve limited the benefit of chemotherapy when added to radiation treatment. (Author). 87 refs.; 4 figs.; 4 tabs

  13. The Modality-Match Effect in Recognition Memory

    Science.gov (United States)

    Mulligan, Neil W.; Osborn, Katherine

    2009-01-01

    The modality-match effect in recognition refers to superior memory for words presented in the same modality at study and test. Prior research on this effect is ambiguous and inconsistent. The present study demonstrates that the modality-match effect is found when modality is rendered salient at either encoding or retrieval. Specifically, in…

  14. Condition Monitoring Of Operating Pipelines With Operational Modal Analysis Application

    Directory of Open Access Journals (Sweden)

    Mironov Aleksey

    2015-12-01

    Full Text Available In the petroleum, natural gas and petrochemical industries, great attention is being paid to safety, reliability and maintainability of equipment. There are a number of technologies to monitor, control, and maintain gas, oil, water, and sewer pipelines. The paper focuses on operational modal analysis (OMA application for condition monitoring of operating pipelines. Special focus is on the topicality of OMA for definition of the dynamic features of the pipeline (frequencies and mode shapes in operation. The research was conducted using two operating laboratory models imitated a part of the operating pipeline. The results of finite-element modeling, identification of pipe natural modes and its modification under the influence of virtual failure are discussed. The work considers the results of experimental research of dynamic behavior of the operating pipe models using one of OMA techniques and comparing dynamic properties with the modeled data. The study results demonstrate sensitivity of modal shape parameters to modification of operating pipeline technical state. Two strategies of pipeline repair – with continuously condition-based monitoring with proposed technology and without such monitoring, was discussed. Markov chain reliability models for each strategy were analyzed and reliability improvement factor for proposed technology of monitoring in compare with traditional one was evaluated. It is resumed about ability of operating pipeline condition monitoring by measuring dynamic deformations of the operating pipe and OMA techniques application for dynamic properties extraction.

  15. MPLM On-Orbit Interface Dynamic Flexibility Modal Test

    Science.gov (United States)

    Bookout, Paul S.; Rodriguez, Pedro I.; Tinson, Ian; Fleming, Paolo

    2001-01-01

    Now that the International Space Station (ISS) is being constructed, payload developers have to not only verify the Shuttle-to-payload interface, but also the interfaces their payload will have with the ISS. The Multi Purpose Logistic Module (MPLM) being designed and built by Alenia Spazio in Torino, Italy is one such payload. The MPLM is the primary carrier for the ISS Payload Racks, Re-supply Stowage Racks, and the Resupply Stowage Platforms to re-supply the ISS with food, water, experiments, maintenance equipment and etc. During the development of the MPLM there was no requirement for verification of the on-orbit interfaces with the ISS. When this oversight was discovered, all the dynamic test stands had already been disassembled. A method was needed that would not require an extensive testing stand and could be completed in a short amount of time. The residual flexibility testing technique was chosen. The residual flexibility modal testing method consists of measuring the free-free natural frequencies and mode shapes along with the interface frequency response functions (FRF's). Analytically, the residual flexibility method has been investigated in detail by, MacNeal, Martinez, Carne, and Miller, and Rubin, but has not been implemented extensively for model correlation due to difficulties in data acquisition. In recent years improvement of data acquisition equipment has made possible the implementation of the residual flexibility method as in Admire, Tinker, and Ivey, and Klosterman and Lemon. The residual flexibility modal testing technique is applicable to a structure with distinct points (DOF) of contact with its environment, such as the MPLM-to-Station interface through the Common Berthing Mechanism (CBM). The CBM is bolted to a flange on the forward cone of the MPLM. During the fixed base test (to verify Shuttle interfaces) some data was gathered on the forward cone panels. Even though there was some data on the forward cones, an additional modal test was

  16. Modal-Based Design Improvement of a Butterfly Valve Disc

    Directory of Open Access Journals (Sweden)

    Marius Draghiciu

    2017-11-01

    Full Text Available The dynamic behaviour control of a butterfly valve is important because, when one of the valve disc natural frequency is close to the frequency of vortex shedding, which appears when the valve is fully open or partially closed, resonance may appear and vibration with significant amplitudes is generated. This paper presents an example by how the design of a butterfly valve disc can be improved by using a modal analysis performed by means of the finite element method. For this purpose, the research reveals the way in which the natural frequencies of the disc can be modified by applying stiffening ribs or changing the dimensions, respective the position of these ribs.

  17. Repositioning Recitation Input in College English Teaching

    Science.gov (United States)

    Xu, Qing

    2009-01-01

    This paper tries to discuss how recitation input helps overcome the negative influences on the basis of second language acquisition theory and confirms the important role that recitation input plays in improving college students' oral and written English.

  18. Refinement Checking on Parametric Modal Transition Systems

    DEFF Research Database (Denmark)

    Benes, Nikola; Kretínsky, Jan; Larsen, Kim Guldstrand

    2015-01-01

    Modal transition systems (MTS) is a well-studied specification formalism of reactive systems supporting a step-wise refinement methodology. Despite its many advantages, the formalism as well as its currently known extensions are incapable of expressing some practically needed aspects in the refin...

  19. Dynamic analysis of pipings by Modal Synthesis

    International Nuclear Information System (INIS)

    Augusto, O.B.; Mattar Neto, M.

    1986-01-01

    A Modal Synthesis method, the component modes, and its implementation as a post-processor of finite element program is presented. Examples of calculations of stationary and transient vibrations for monitoring pipelines of nuclear power plants are analysed. (M.C.K.) [pt

  20. Established rheumatoid arthritis - new imaging modalities

    DEFF Research Database (Denmark)

    McQueen, Fiona M; Østergaard, Mikkel

    2007-01-01

    New imaging modalities are assuming an increasingly important role in the investigation and management of rheumatoid arthritis. It is now possible to obtain information about all tissues within the joint in three dimensions using tomographic techniques such as magnetic resonance imaging (MRI...

  1. Nanomaterials Toxicity and Cell Death Modalities

    Directory of Open Access Journals (Sweden)

    Daniela De Stefano

    2012-01-01

    Full Text Available In the last decade, the nanotechnology advancement has developed a plethora of novel and intriguing nanomaterial application in many sectors, including research and medicine. However, many risks have been highlighted in their use, particularly related to their unexpected toxicity in vitro and in vivo experimental models. This paper proposes an overview concerning the cell death modalities induced by the major nanomaterials.

  2. Dual-Modality Breast Tomosynthesis1

    OpenAIRE

    Williams, Mark B.; Judy, Patricia G.; Gunn, Spencer; Majewski, Stanislaw

    2010-01-01

    Pilot clinical evaluation of this dual-modality tomosynthesis system suggests that it is a feasible and accurate method with which to detect and diagnose breast cancer and that specificity and positive predictive value can be improved by adding molecular breast imaging tomosynthesis to x-ray tomosynthesis.

  3. Sensor Placement for Modal Parameter Subset Estimation

    DEFF Research Database (Denmark)

    Ulriksen, Martin Dalgaard; Bernal, Dionisio; Damkilde, Lars

    2016-01-01

    The present paper proposes an approach for deciding on sensor placements in the context of modal parameter estimation from vibration measurements. The approach is based on placing sensors, of which the amount is determined a priori, such that the minimum Fisher information that the frequency resp...

  4. Learning Modalities--Should They Be Considered?

    Science.gov (United States)

    Jones, John Paul

    The author summarizes and reviews seven research studies which seek to determine the role of individual modal preference as related to learning to read. The seven studies are by Bateman (1968); Robinson (1968); Jones (1970); Bruininks (1968); Cripe (1966); de Hirsh, Jansky, and Langford (1966); and Bursuk (1971). Of these studies, only Bursuk…

  5. The Fourier modal method for aperiodic structures

    NARCIS (Netherlands)

    Pisarenco, M.; Maubach, J.M.L.; Setija, I.D.; Mattheij, R.M.M.

    2010-01-01

    This paper extends the area of application of the Fourier modal method from periodic structures to non-periodic ones illuminated under arbitrary angles. This is achieved by placing perfectly matched layers at the lateral boundaries and reformulating the problem in terms of a contrast field.

  6. Current diagnostic modalities for vulnerable plaque detection

    NARCIS (Netherlands)

    J.A. Schaar (Johannes); F. Mastik (Frits); E.S. Regar (Eveline); C.A. den Uil (Corstiaan); F.J.H. Gijsen (Frank); J.J. Wentzel (Jolanda); P.W.J.C. Serruys (Patrick); A.F.W. van der Steen (Ton)

    2007-01-01

    textabstractRupture of vulnerable plaques is the main cause of acute coronary syndrome and myocardial infarction. Identification of vulnerable plaques is therefore essential to enable the development of treatment modalities to stabilize such plaques. Several diagnostic methods are currently tested

  7. Computing modal dispersion characteristics of radially Asymmetric ...

    African Journals Online (AJOL)

    We developed a matrix theory that applies to with non-circular/circular but concentric layers fibers. And we compute the dispersion characteristics of radially unconventional fiber, known as Asymmetric Bragg fiber. An attempt has been made to determine how the modal characteristics change as circular Bragg fiber is ...

  8. Does frequency count? Parental input and the acquisition of vocabulary.

    Science.gov (United States)

    Goodman, Judith C; Dale, Philip S; Li, Ping

    2008-08-01

    Studies examining factors that influence when words are learned typically investigate one lexical category or a small set of words. We provide the first evaluation of the relation between input frequency and age of acquisition for a large sample of words. The MacArthur-Bates Communicative Development Inventory provides norming data on age of acquisition for 562 individual words collected from the parents of children aged 0 ; 8 to 2 ; 6. The CHILDES database provides estimates of frequency with which parents use these words with their children (age: 0 ; 7-7 ; 5; mean age: 36 months). For production, across all words higher parental frequency is associated with later acquisition. Within lexical categories, however, higher frequency is related to earlier acquisition. For comprehension, parental frequency correlates significantly with the age of acquisition only for common nouns. Frequency effects change with development. Thus, frequency impacts vocabulary acquisition in a complex interaction with category, modality and developmental stage.

  9. Textual Enhancement of Input: Issues and Possibilities

    Science.gov (United States)

    Han, ZhaoHong; Park, Eun Sung; Combs, Charles

    2008-01-01

    The input enhancement hypothesis proposed by Sharwood Smith (1991, 1993) has stimulated considerable research over the last 15 years. This article reviews the research on textual enhancement of input (TE), an area where the majority of input enhancement studies have aggregated. Methodological idiosyncrasies are the norm of this body of research.…

  10. 7 CFR 3430.607 - Stakeholder input.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 15 2010-01-01 2010-01-01 false Stakeholder input. 3430.607 Section 3430.607 Agriculture Regulations of the Department of Agriculture (Continued) COOPERATIVE STATE RESEARCH, EDUCATION... § 3430.607 Stakeholder input. CSREES shall seek and obtain stakeholder input through a variety of forums...

  11. 7 CFR 3430.15 - Stakeholder input.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 15 2010-01-01 2010-01-01 false Stakeholder input. 3430.15 Section 3430.15... Stakeholder input. Section 103(c)(2) of the Agricultural Research, Extension, and Education Reform Act of 1998... RFAs for competitive programs. CSREES will provide instructions for submission of stakeholder input in...

  12. PENGARUH GOOD CORPORATE GOVERNANCE, KINERJA KEUANGAN, MODAL INTELEKTUAL TERHADAP PENGUNGKAPAN MODAL INTELEKTUAL

    Directory of Open Access Journals (Sweden)

    Gilang Anies Saendy

    2015-10-01

    Full Text Available Dampak perkembangan globalisasi membutuhkan informasi lebih lanjut, terutama informasi tentang modal intelektual perusahaan. Tapi, dalam kondisi nyata informasi modal intelektual masih rendah, yakni sekitar 27-35%. Objek penelitian ini adalah perbankan yang terdapat dalam direktori Pasar Modal Indonesia (ICMD 2010-2013. Jumlah populasi adalah 36 perbankan dan 17 sampel dengan menggunakan purposive sampling. Metode yang digunakan adalah analisis jalur. Hasil penelitian ini menunjukkan bahwa tidak pengaruh antara pelaksanaan GCG untuk pengungkapan modal intelektual dan kinerja keuangan. Selain itu, ada pengaruh positif antara kinerja modal intelektual terhadap kinerja keuangan dan kinerja keuangan untuk pengungkapan modal intelektual. Selanjutnya, hasil penelitian menunjukkan bahwa tidak efek mediasi melalui kinerja keuangan perusahaan antara implementasi GCG dalam pengungkapan modal intelektual. Hasilnya juga mengatakan ada efek mediasi antara pelaksanaan GCG untuk pengungkapan modal intelektual pikir kinerja modal intelektual. The development due to the increase of globalization gives impact to the need of having more information. One of them is the need to have information on company’s intellectual capital. But, in real condition, intellectual capital information is still low. It is about 27-35%. The objects of this research are banks organized in Indonesian Capital Market Directory (ICMD from 2010-2013. Total populations were 36 banks, and finally 17 samples were selected by using purposive sampling. The method used is path analysis. The results of this research show that there is no influence between GCG’s implementation on intellectual capital disclosure and financial performance. However, there are  positive influences of intellectual capital performance on the financial performance, and financial performance on the disclosure of intellectual capital. Besides, this research said that there is no effect of mediation through the company

  13. Audiovisual synchrony enhances BOLD responses in a brain network including multisensory STS while also enhancing target-detection performance for both modalities

    Science.gov (United States)

    Marchant, Jennifer L; Ruff, Christian C; Driver, Jon

    2012-01-01

    The brain seeks to combine related inputs from different senses (e.g., hearing and vision), via multisensory integration. Temporal information can indicate whether stimuli in different senses are related or not. A recent human fMRI study (Noesselt et al. [2007]: J Neurosci 27:11431–11441) used auditory and visual trains of beeps and flashes with erratic timing, manipulating whether auditory and visual trains were synchronous or unrelated in temporal pattern. A region of superior temporal sulcus (STS) showed higher BOLD signal for the synchronous condition. But this could not be related to performance, and it remained unclear if the erratic, unpredictable nature of the stimulus trains was important. Here we compared synchronous audiovisual trains to asynchronous trains, while using a behavioral task requiring detection of higher-intensity target events in either modality. We further varied whether the stimulus trains had predictable temporal pattern or not. Synchrony (versus lag) between auditory and visual trains enhanced behavioral sensitivity (d') to intensity targets in either modality, regardless of predictable versus unpredictable patterning. The analogous contrast in fMRI revealed BOLD increases in several brain areas, including the left STS region reported by Noesselt et al. [2007: J Neurosci 27:11431–11441]. The synchrony effect on BOLD here correlated with the subject-by-subject impact on performance. Predictability of temporal pattern did not affect target detection performance or STS activity, but did lead to an interaction with audiovisual synchrony for BOLD in inferior parietal cortex. PMID:21953980

  14. Unitary input DEA model to identify beef cattle production systems typologies

    Directory of Open Access Journals (Sweden)

    Eliane Gonçalves Gomes

    2012-08-01

    Full Text Available The cow-calf beef production sector in Brazil has a wide variety of operating systems. This suggests the identification and the characterization of homogeneous regions of production, with consequent implementation of actions to achieve its sustainability. In this paper we attempted to measure the performance of 21 livestock modal production systems, in their cow-calf phase. We measured the performance of these systems, considering husbandry and production variables. The proposed approach is based on data envelopment analysis (DEA. We used unitary input DEA model, with apparent input orientation, together with the efficiency measurements generated by the inverted DEA frontier. We identified five modal production systems typologies, using the isoefficiency layers approach. The results showed that the knowledge and the processes management are the most important factors for improving the efficiency of beef cattle production systems.

  15. Conflict when making decisions about dialysis modality.

    Science.gov (United States)

    Chen, Nien-Hsin; Lin, Yu-Ping; Liang, Shu-Yuan; Tung, Heng-Hsin; Tsay, Shiow-Luan; Wang, Tsae-Jyy

    2018-01-01

    To explore decisional conflict and its influencing factors on choosing dialysis modality in patients with end-stage renal diseases. The influencing factors investigated include demographics, predialysis education, dialysis knowledge, decision self-efficacy and social support. Making dialysis modality decisions can be challenging for patients with end-stage renal diseases; there are pros and cons to both haemodialysis and peritoneal dialysis. Patients are often uncertain as to which one will be the best alternative for them. This decisional conflict increases the likelihood of making a decision that is not based on the patient's values or preferences and may result in undesirable postdecisional consequences. Addressing factors predisposing patients to decisional conflict helps to facilitate informed decision-making and then to improve healthcare quality. A predictive correlational cross-sectional study design was used. Seventy patients were recruited from the outpatient dialysis clinics of two general hospitals in Taiwan. Data were collected with study questionnaires, including questions on demographics, dialysis modality and predialysis education, the Dialysis Knowledge Scale, the Decision Self-Efficacy scale, the Social Support Scale, and the Decisional Conflict Scale. The mean score on the Decisional Conflict Scale was 29.26 (SD = 22.18). Decision self-efficacy, dialysis modality, predialysis education, professional support and dialysis knowledge together explained 76.4% of the variance in decisional conflict. Individuals who had lower decision self-efficacy, did not receive predialysis education on both haemodialysis and peritoneal dialysis, had lower dialysis knowledge and perceived lower professional support reported higher decisional conflict on choosing dialysis modality. When providing decisional support to predialysis stage patients, practitioners need to increase patients' decision self-efficacy, provide both haemodialysis and peritoneal dialysis

  16. Learning normalized inputs for iterative estimation in medical image segmentation.

    Science.gov (United States)

    Drozdzal, Michal; Chartrand, Gabriel; Vorontsov, Eugene; Shakeri, Mahsa; Di Jorio, Lisa; Tang, An; Romero, Adriana; Bengio, Yoshua; Pal, Chris; Kadoury, Samuel

    2018-02-01

    In this paper, we introduce a simple, yet powerful pipeline for medical image segmentation that combines Fully Convolutional Networks (FCNs) with Fully Convolutional Residual Networks (FC-ResNets). We propose and examine a design that takes particular advantage of recent advances in the understanding of both Convolutional Neural Networks as well as ResNets. Our approach focuses upon the importance of a trainable pre-processing when using FC-ResNets and we show that a low-capacity FCN model can serve as a pre-processor to normalize medical input data. In our image segmentation pipeline, we use FCNs to obtain normalized images, which are then iteratively refined by means of a FC-ResNet to generate a segmentation prediction. As in other fully convolutional approaches, our pipeline can be used off-the-shelf on different image modalities. We show that using this pipeline, we exhibit state-of-the-art performance on the challenging Electron Microscopy benchmark, when compared to other 2D methods. We improve segmentation results on CT images of liver lesions, when contrasting with standard FCN methods. Moreover, when applying our 2D pipeline on a challenging 3D MRI prostate segmentation challenge we reach results that are competitive even when compared to 3D methods. The obtained results illustrate the strong potential and versatility of the pipeline by achieving accurate segmentations on a variety of image modalities and different anatomical regions. Copyright © 2017 Elsevier B.V. All rights reserved.

  17. Innovations for Natural Resource Management

    Indian Academy of Sciences (India)

    First page Back Continue Last page Graphics. Improving input use efficiency and sustainable management of natural resource endowments - a continuous challenge. Improving input use efficiency and sustainable management of natural resource endowments - a continuous challenge. Innovations have focused on ...

  18. Turn customer input into innovation.

    Science.gov (United States)

    Ulwick, Anthony W

    2002-01-01

    It's difficult to find a company these days that doesn't strive to be customer-driven. Too bad, then, that most companies go about the process of listening to customers all wrong--so wrong, in fact, that they undermine innovation and, ultimately, the bottom line. What usually happens is this: Companies ask their customers what they want. Customers offer solutions in the form of products or services. Companies then deliver these tangibles, and customers just don't buy. The reason is simple--customers aren't expert or informed enough to come up with solutions. That's what your R&D team is for. Rather, customers should be asked only for outcomes--what they want a new product or service to do for them. The form the solutions take should be up to you, and you alone. Using Cordis Corporation as an example, this article describes, in fine detail, a series of effective steps for capturing, analyzing, and utilizing customer input. First come indepth interviews, in which a moderator works with customers to deconstruct a process or activity in order to unearth "desired outcomes." Addressing participants' comments one at a time, the moderator rephrases them to be both unambiguous and measurable. Once the interviews are complete, researchers then compile a comprehensive list of outcomes that participants rank in order of importance and degree to which they are satisfied by existing products. Finally, using a simple mathematical formula called the "opportunity calculation," researchers can learn the relative attractiveness of key opportunity areas. These data can be used to uncover opportunities for product development, to properly segment markets, and to conduct competitive analysis.

  19. PREVIMER : Meteorological inputs and outputs

    Science.gov (United States)

    Ravenel, H.; Lecornu, F.; Kerléguer, L.

    2009-09-01

    PREVIMER is a pre-operational system aiming to provide a wide range of users, from private individuals to professionals, with short-term forecasts about the coastal environment along the French coastlines bordering the English Channel, the Atlantic Ocean, and the Mediterranean Sea. Observation data and digital modelling tools first provide 48-hour (probably 96-hour by summer 2009) forecasts of sea states, currents, sea water levels and temperatures. The follow-up of an increasing number of biological parameters will, in time, complete this overview of coastal environment. Working in partnership with the French Naval Hydrographic and Oceanographic Service (Service Hydrographique et Océanographique de la Marine, SHOM), the French National Weather Service (Météo-France), the French public science and technology research institute (Institut de Recherche pour le Développement, IRD), the European Institute of Marine Studies (Institut Universitaire Européen de la Mer, IUEM) and many others, IFREMER (the French public institute fo marine research) is supplying the technologies needed to ensure this pertinent information, available daily on Internet at http://www.previmer.org, and stored at the Operational Coastal Oceanographic Data Centre. Since 2006, PREVIMER publishes the results of demonstrators assigned to limited geographic areas and to specific applications. This system remains experimental. The following topics are covered : Hydrodynamic circulation, sea states, follow-up of passive tracers, conservative or non-conservative (specifically of microbiological origin), biogeochemical state, primary production. Lastly, PREVIMER provides researchers and R&D departments with modelling tools and access to the database, in which the observation data and the modelling results are stored, to undertake environmental studies on new sites. The communication will focus on meteorological inputs to and outputs from PREVIMER. It will draw the lessons from almost 3 years during

  20. Correlation Results for a Mass Loaded Vehicle Panel Test Article Finite Element Models and Modal Survey Tests

    Science.gov (United States)

    Maasha, Rumaasha; Towner, Robert L.

    2012-01-01

    High-fidelity Finite Element Models (FEMs) were developed to support a recent test program at Marshall Space Flight Center (MSFC). The FEMs correspond to test articles used for a series of acoustic tests. Modal survey tests were used to validate the FEMs for five acoustic tests (a bare panel and four different mass-loaded panel configurations). An additional modal survey test was performed on the empty test fixture (orthogrid panel mounting fixture, between the reverb and anechoic chambers). Modal survey tests were used to test-validate the dynamic characteristics of FEMs used for acoustic test excitation. Modal survey testing and subsequent model correlation has validated the natural frequencies and mode shapes of the FEMs. The modal survey test results provide a basis for the analysis models used for acoustic loading response test and analysis comparisons

  1. Altered Cross-Modal Processing in the Primary Auditory Cortex of Congenitally Deaf Adults: A Visual-Somatosensory fMRI Study with a Double-Flash Illusion

    OpenAIRE

    Karns, Christina M.; Dow, Mark W.; Neville, Helen J.

    2012-01-01

    The developing brain responds to the environment by using statistical correlations in input to guide functional and structural changes—that is, the brain displays neuroplasticity. Experience shapes brain development throughout life, but neuroplasticity is variable from one brain system to another. How does the early loss of a sensory modality affect this complex process? We examined cross-modal neuroplasticity in anatomically defined subregions of Heschl's gyrus, the site of human primary aud...

  2. Supervised Cross-Modal Factor Analysis for Multiple Modal Data Classification

    KAUST Repository

    Wang, Jingbin

    2015-10-09

    In this paper we study the problem of learning from multiple modal data for purpose of document classification. In this problem, each document is composed two different modals of data, i.e., An image and a text. Cross-modal factor analysis (CFA) has been proposed to project the two different modals of data to a shared data space, so that the classification of a image or a text can be performed directly in this space. A disadvantage of CFA is that it has ignored the supervision information. In this paper, we improve CFA by incorporating the supervision information to represent and classify both image and text modals of documents. We project both image and text data to a shared data space by factor analysis, and then train a class label predictor in the shared space to use the class label information. The factor analysis parameter and the predictor parameter are learned jointly by solving one single objective function. With this objective function, we minimize the distance between the projections of image and text of the same document, and the classification error of the projection measured by hinge loss function. The objective function is optimized by an alternate optimization strategy in an iterative algorithm. Experiments in two different multiple modal document data sets show the advantage of the proposed algorithm over other CFA methods.

  3. Modal Testing of Mechanical Structures subject to Operational Excitation Forces

    DEFF Research Database (Denmark)

    Møller, N.; Brincker, Rune; Herlufsen, H.

    2001-01-01

    Operational Modal Analysis also known as Output Only Modal Analysis has in the recent years been used for extracting modal parameters of civil engineering structures and is now becoming popular for mechanical structures. The advantage of the method is that no artificial excitation need to be appl......Operational Modal Analysis also known as Output Only Modal Analysis has in the recent years been used for extracting modal parameters of civil engineering structures and is now becoming popular for mechanical structures. The advantage of the method is that no artificial excitation need...

  4. Model Design of Piezoelectric Micromachined Modal Gyroscope

    Directory of Open Access Journals (Sweden)

    Xiaojun Hu

    2011-01-01

    Full Text Available This paper reports a novel kind of solid-state microgyroscope, which is called piezoelectric micromachined modal gyroscope (PMMG. PMMG has large stiffness and robust resistance to shake and strike because there is no evident mass-spring component in its structure. This work focused on quantitative optimization of the gyroscope, which is still blank for such gyroscope. The modal analysis by the finite element method (FEM was firstly conducted. A set of quantitative indicators were developed to optimize the operation mode. By FEM, the harmonic analysis was conducted to find the way to efficiently actuate the operational mode needed. The optimal configuration of driving electrodes was obtained. At last, the Coriolis analysis was conducted to show the relation between angular velocity and differential output voltage by the Coriolis force under working condition. The results obtained in this paper provide theoretical basis for realizing this novel kind of micromachined gyroscope.

  5. Modality shift effects mimic multisensory interactions

    DEFF Research Database (Denmark)

    Gondan, Matthias; Vorberg, D.; Greenlee, M.W.

    2007-01-01

    be avoided using an additional tactile stimulus (T) and evaluating the ERP difference (T + TAV) - (TA + TV). A second possible confound is the modality shift effect (MSE): for example, the auditory N1 is increased if an auditory stimulus follows a visual stimulus, whereas it is smaller if the modality......A frequent approach to study interactions of the auditory and the visual system is to measure event-related potentials (ERPs) to auditory, visual, and auditory-visual stimuli (A, V, AV). A nonzero result of the AV - (A + V) comparison indicates that the sensory systems interact at a specific...... processing stage. Two possible biases weaken the conclusions drawn by this approach: first, subtracting two ERPs from one requires that A, V, and AV do not share any common activity. We have shown before (Gondan and Röder in Brain Res 1073-1074:389-397, 2006) that the problem of common activity can...

  6. Kinetic Study of Curcumin on Modal Fabric

    Directory of Open Access Journals (Sweden)

    Abu Naser Md. Ahsanul Haque

    2018-03-01

    Full Text Available A kinetic study of curcumin on modal fabric was carried out using an initial dye concentration of 1 g/L at three different temperatures, 70 °C, 85 °C and 100 °C, at pH 7 and an material to liquor ratio of 1:20. Pseudo first-order and pseudo second-order kinetics were applied, and it was found that the adsorption kinetics of curcumin on modal fabric matched the pseudo second-order kinetic model. The activation energy was found to be equal to 71.14 kJ/mol, while the enthalpy and entropy of activation were 68.16 kJ/mol and –66.02 J/molK respectively.

  7. MOSFET dosimetry on modern radiation oncology modalities

    International Nuclear Information System (INIS)

    Rosenfeld, A.B.

    2002-01-01

    The development of MOSFET dosimetry is presented with an emphasis on the development of a scanning MOSFET dosimetry system for modern radiation oncology modalities. Fundamental aspects of MOSFETs in relation to their use as dosemeters are briefly discussed. The performance of MOSFET dosemeters in conformal radiotherapy, hadron therapy, intensity-modulated radiotherapy and microbeam radiation therapy is compared with other dosimetric techniques. In particular the application of MOSFET dosemeters in the characterisation and quality assurance of the steep dose gradients associated with the penumbra of some modern radiation oncology modalities is investigated. A new in vivo, on-line, scanning MOSFET read out system is also presented. The system has the ability to read out multiple MOSFET dosemeters with excellent spatial resolution and temperature stability and minimal slow border trapping effects. (author)

  8. The life trajectories modality of oral history

    Directory of Open Access Journals (Sweden)

    Rita de Cássia Gonçalves

    2007-05-01

    Full Text Available This article seeks to explore the potential of qualitative research. It presents the life trajectory modality of the oral history method, to discuss the possibility of its utilization in scientific research in the Social Work profession. The epistemological foundations of oral history are discussed to establish its scientific character. The life trajectories modality is presented as a historic and social construction that utilizes different interview techniques to give voice to previously invisible subjects, indicating the principal phases of the methodological procedures used in this approach. The conclusions highlight the importance of the construction of this model and its projection as a research proposal that implies a process of understanding and analyzing the social universes that are contextualized and interconnected, considering the realities of the life trajectories of the subjects studied.

  9. Deception Detection, Transmission, & Modality in Age & Sex

    Directory of Open Access Journals (Sweden)

    Charlotte Dorothy Sweeney

    2014-06-01

    Full Text Available This study is the first to create and use spontaneous (i.e. unrehearsed pro-social lies in an ecological setting. Creation of the stimuli involved fifty-one older adult and forty-four college student senders who lied authentically in that their lies were spontaneous in the service of protecting a research assistant. In the main study, seventy-seven older adult and eighty-four college raters attempted to detect lies in the older adult and college senders in three modalities: audio, visual, and audiovisual. Raters of both age groups were best at detecting lies in the audiovisual and worst in the visual modalities. Overall, college students were better detectors than older adults. There was an age-matching effect for college students but not for older adults. Older adult males were the hardest to detect. The older the adult was the worse the ability to detect deception.

  10. Breast Cancer Screening, Mammography, and Other Modalities.

    Science.gov (United States)

    Fiorica, James V

    2016-12-01

    This article is an overview of the modalities available for breast cancer screening. The modalities discussed include digital mammography, digital breast tomosynthesis, breast ultrasonography, magnetic resonance imaging, and clinical breast examination. There is a review of pertinent randomized controlled trials, studies and meta-analyses which contributed to the evolution of screening guidelines. Ultimately, 5 major medical organizations formulated the current screening guidelines in the United States. The lack of consensus in these guidelines represents an ongoing controversy about the optimal timing and method for breast cancer screening in women. For mammography screening, the Breast Imaging Reporting and Data System lexicon is explained which corresponds with recommended clinical management. The presentation and discussion of the data in this article are designed to help the clinician individualize breast cancer screening for each patient.

  11. Focused labeled proof systems for modal logic

    OpenAIRE

    Miller , Dale; Volpe , Marco

    2015-01-01

    International audience; Focused proofs are sequent calculus proofs that group inference rules into alternating positive and negative phases. These phases can then be used to define macro-level inference rules from Gentzen's original and tiny introduction and structural rules. We show here that the inference rules of labeled proof systems for modal logics can similarly be described as pairs of such phases within the LKF focused proof system for first-order classical logic. We consider the syst...

  12. A Transgenic Tri-Modality Reporter Mouse

    OpenAIRE

    Yan, Xinrui; Ray, Pritha; Paulmurugan, Ramasamy; Tong, Ricky; Gong, Yongquan; Sathirachinda, Ataya; Wu, Joseph C.; Gambhir, Sanjiv S.

    2013-01-01

    Transgenic mouse with a stably integrated reporter gene(s) can be a valuable resource for obtaining uniformly labeled stem cells, tissues, and organs for various applications. We have generated a transgenic mouse model that ubiquitously expresses a tri-fusion reporter gene (fluc2-tdTomato-ttk) driven by a constitutive chicken β-actin promoter. This "Tri-Modality Reporter Mouse" system allows one to isolate most cells from this donor mouse and image them for bioluminescent (fluc2), fluorescent...

  13. Treatment modalities of palatal impacted canines

    OpenAIRE

    Dimova, Cena; Papakoca, Kiro; Ristoska, Sonja; Kovacevska, Ivona

    2012-01-01

    Introduction: The orthodontic treatment of impacted maxillary canine remains a challenge to today’s clinicians. The treatment of this clinical entity usually involves surgical exposure of the impacted tooth, followed by orthodontic traction to guide and align it into the dental arch. The impacted palatal canine requires a combination of both treatment modalities: orthodontic management and oral surgical treatment. Two types of approach are commonly used: simple exposure, or exposure with brac...

  14. Multi modal child-to-child interaction

    DEFF Research Database (Denmark)

    Fisker, Tine Basse

    In this presentation the interaction and relation of three boys is analyzed using multi modal analysis. The analysis clearly, and surprisingly demonstrates that the boys interact via different modes and that they are able to handle several interaction partners at the same time. They co......-construct interaction in rather complex and unexpected ways using verbal as well as non-verbal modes in interaction....

  15. A method for experimental modal separation

    Science.gov (United States)

    Hallauer, W. L., Jr.

    1977-01-01

    A method is described for the numerical simulation of multiple-shaker modal survey testing using simulated experimental data to optimize the shaker force-amplitude distribution for the purpose of isolating individual modes of vibration. Inertia, damping, stiffness, and model data are stored on magnetic disks, available by direct access to the interactive FORTRAN programs which perform all computations required by this relative force amplitude distribution method.

  16. Modality-specificity of Selective Attention Networks

    OpenAIRE

    Stewart, Hannah J.; Amitay, Sygal

    2015-01-01

    Objective: To establish the modality specificity and generality of selective attention networks. Method: Forty-eight young adults completed a battery of four auditory and visual selective attention tests based upon the Attention Network framework: the visual and auditory Attention Network Tests (vANT, aANT), the Test of Everyday Attention (TEA), and the Test of Attention in Listening (TAiL). These provided independent measures for auditory and visual alerting, orienting, and conflict resoluti...

  17. Non-modal analysis in plasmas

    International Nuclear Information System (INIS)

    Mahajan, S.M.; Rogava, A.D.; Berezhiani, V.

    1996-01-01

    The techniques of non-modal analysis are applied to investigate the time evolution of a variety of plasma flows with velocity shear. It is shown that large transient amplifications may result for appropriate initial perturbations. The role of this amplification in determining the nonlinear dynamics of these systems (when all the normal modes are stable) is discussed. Examples are taken from Laboratory, astrophysical and cosmic plasmas

  18. Imaging Breast Density: Established and Emerging Modalities

    Directory of Open Access Journals (Sweden)

    Jeon-Hor Chen

    2015-12-01

    Full Text Available Mammographic density has been proven as an independent risk factor for breast cancer. Women with dense breast tissue visible on a mammogram have a much higher cancer risk than women with little density. A great research effort has been devoted to incorporate breast density into risk prediction models to better estimate each individual’s cancer risk. In recent years, the passage of breast density notification legislation in many states in USA requires that every mammography report should provide information regarding the patient’s breast density. Accurate definition and measurement of breast density are thus important, which may allow all the potential clinical applications of breast density to be implemented. Because the two-dimensional mammography-based measurement is subject to tissue overlapping and thus not able to provide volumetric information, there is an urgent need to develop reliable quantitative measurements of breast density. Various new imaging technologies are being developed. Among these new modalities, volumetric mammographic density methods and three-dimensional magnetic resonance imaging are the most well studied. Besides, emerging modalities, including different x-ray–based, optical imaging, and ultrasound-based methods, have also been investigated. All these modalities may either overcome some fundamental problems related to mammographic density or provide additional density and/or compositional information. The present review article aimed to summarize the current established and emerging imaging techniques for the measurement of breast density and the evidence of the clinical use of these density methods from the literature.

  19. Quantitative multi-modal NDT data analysis

    International Nuclear Information System (INIS)

    Heideklang, René; Shokouhi, Parisa

    2014-01-01

    A single NDT technique is often not adequate to provide assessments about the integrity of test objects with the required coverage or accuracy. In such situations, it is often resorted to multi-modal testing, where complementary and overlapping information from different NDT techniques are combined for a more comprehensive evaluation. Multi-modal material and defect characterization is an interesting task which involves several diverse fields of research, including signal and image processing, statistics and data mining. The fusion of different modalities may improve quantitative nondestructive evaluation by effectively exploiting the augmented set of multi-sensor information about the material. It is the redundant information in particular, whose quantification is expected to lead to increased reliability and robustness of the inspection results. There are different systematic approaches to data fusion, each with its specific advantages and drawbacks. In our contribution, these will be discussed in the context of nondestructive materials testing. A practical study adopting a high-level scheme for the fusion of Eddy Current, GMR and Thermography measurements on a reference metallic specimen with built-in grooves will be presented. Results show that fusion is able to outperform the best single sensor regarding detection specificity, while retaining the same level of sensitivity

  20. TESS Lens-Bezel Assembly Modal Testing

    Science.gov (United States)

    Dilworth, Brandon J.; Karlicek, Alexandra

    2017-01-01

    The Transiting Exoplanet Survey Satellite (TESS) program, led by the Kavli Institute for Astrophysics and Space Research at the Massachusetts Institute of Technology (MIT) will be the first-ever spaceborne all-sky transit survey. MIT Lincoln Laboratory is responsible for the cameras, including the lens assemblies, detector assemblies, lens hoods, and camera mounts. TESS is scheduled to be launched in August of 2017 with the primary goal to detect small planets with bright host starts in the solar neighborhood, so that detailed characterizations of the planets and their atmospheres can be performed. The TESS payload consists of four identical cameras and a data handling unit. Each camera consists of a lens assembly with seven optical elements and a detector assembly with four charge-coupled devices (CCDs) including their associated electronics. The optical prescription requires that several of the lenses are in close proximity to a neighboring element. A finite element model (FEM) was developed to estimate the relative deflections between each lens-bezel assembly under launch loads to predict that there are adequate clearances preventing the lenses from making contact. Modal tests using non-contact response measurements were conducted to experimentally estimate the modal parameters of the lens-bezel assembly, and used to validate the initial FEM assumptions. Key Words Non-contact measurements, modal analysis, model validation

  1. Input filter compensation for switching regulators

    Science.gov (United States)

    Lee, F. C.; Kelkar, S. S.

    1982-01-01

    The problems caused by the interaction between the input filter, output filter, and the control loop are discussed. The input filter design is made more complicated because of the need to avoid performance degradation and also stay within the weight and loss limitations. Conventional input filter design techniques are then dicussed. The concept of pole zero cancellation is reviewed; this concept is the basis for an approach to control the peaking of the output impedance of the input filter and thus mitigate some of the problems caused by the input filter. The proposed approach for control of the peaking of the output impedance of the input filter is to use a feedforward loop working in conjunction with feedback loops, thus forming a total state control scheme. The design of the feedforward loop for a buck regulator is described. A possible implementation of the feedforward loop design is suggested.

  2. Organic and Low-Input Dairy Farming: Avenues to Enhance Sustainability and Competitiveness in the EU

    OpenAIRE

    Scollan, Nigel; Padel, Susanne; Halberg, Niels; Hermansen, J.E.; Nicholas, Pip; Rinne, Marketta; Zanoli, Raffaele; Zollitsch, Werner; Lauwers, Ludwig

    2017-01-01

    Whether farming strategies built on continuing input intensification or relying on integrated natural resource management are more sustainable and competitive is at the core of the agricultural development debate. The five-year (2011–16) Sustainable Organic and Low Input Dairying (SOLID) project, funded by the European Commission, involved 25 partners across 10 European countries and was designed to support innovation in European organic and low-input dairy farming. Results show that such sys...

  3. Completely automated modal analysis procedure based on the combination of different OMA methods

    Science.gov (United States)

    Ripamonti, Francesco; Bussini, Alberto; Resta, Ferruccio

    2018-03-01

    In this work a completely automated output-only Modal Analysis procedure is presented and all its benefits are listed. Based on the merging of different Operational Modal Analysis methods and a statistical approach, the identification process has been improved becoming more robust and giving as results only the real natural frequencies, damping ratios and mode shapes of the system. The effect of the temperature can be taken into account as well, leading to the creation of a better tool for automated Structural Health Monitoring. The algorithm has been developed and tested on a numerical model of a scaled three-story steel building present in the laboratories of Politecnico di Milano.

  4. Automated modal tracking and fatigue assessment of a wind turbine based on continuous dynamic monitoring

    Directory of Open Access Journals (Sweden)

    Oliveira Gustavo

    2015-01-01

    Full Text Available The paper describes the implementation of a dynamic monitoring system at a 2.0 MW onshore wind turbine. The system is composed by two components aiming at the structural integrity and fatigue assessment. The first component enables the continuous tracking of modal characteristics of the wind turbine (natural frequency values, modal damping ratios and mode shapes in order to detect abnormal deviations of these properties, which may be caused by the occurrence of structural damage. On the other hand, the second component allows the estimation of the remaining fatigue lifetime of the structure based on the analysis of the measured cycles of structural vibration.

  5. Unilateral deafness in children affects development of multi-modal modulation and default mode networks

    Directory of Open Access Journals (Sweden)

    Vincent eSchmithorst

    2014-03-01

    Full Text Available Monaural auditory input due to congenital or acquired unilateral hearing loss (UHL may have neurobiological effects on the developing brain. Using fMRI, we investigated the effect of UHL on the development of functional brain networks used for cross-modal processing. Children ages 7-12 with moderate or greater unilateral hearing loss of sensorineural origin (UHL-SN; N = 21 and normal-hearing controls (N = 23 performed an fMRI-compatible adaptation of the Token Test involving listening to a sentence such as touched the small green circle and the large blue square and simultaneously viewing an arrow touching colored shapes on a video. Children with right or severe-to-profound UHL-SN displayed smaller activation in a region encompassing the right inferior temporal, middle temporal, and middle occipital gyrus (BA 19/37/39, evidencing differences due to monaural hearing in cross-modal modulation of the visual processing pathway. Children with UHL-SN displayed increased activation in the left posterior superior temporal gyrus, likely the result either of more effortful low-level processing of auditory stimuli or differences in cross-modal modulation of the auditory processing pathway. Additionally, children with UHL-SN displayed reduced deactivation of anterior and posterior regions of the default mode network. Results suggest that monaural hearing affects the development of brain networks related to cross-modal sensory processing and the regulation of the default network during processing of spoken language.

  6. Automated Modal Parameter Estimation of Civil Engineering Structures

    DEFF Research Database (Denmark)

    Andersen, Palle; Brincker, Rune; Goursat, Maurice

    In this paper the problems of doing automatic modal parameter extraction of ambient excited civil engineering structures is considered. Two different approaches for obtaining the modal parameters automatically are presented: The Frequency Domain Decomposition (FDD) technique and a correlation...

  7. On the Relationship Between Input and Interaction Psycholinguistic, Cognitive, and Ecological Perspectives in SLA

    Directory of Open Access Journals (Sweden)

    Parisa Daftarifard

    2010-09-01

    Full Text Available Input is one of the most important elements in the process of second language acquisition (SLA. As Gass (1997 points out, second language learning simply cannot take place without input of some sort. Since then, specific issues have been actively debated in SLA on the nature of input and input processing, such as the amount of input that is necessary for language acquisition, various attributes of input and how they may facilitate or hinder acquisition, and instructional method that may enhance input. In this paper, four hypotheses and paradigms of input processing have been described. It is delineated that although the three paradigms of triggering, input hypothesis, and interaction hypothesis have been widely used and accepted, they lack the ability to account for the dynamic nature of language. Affordance, on the other hand, can account for such a nature of language.
    Therefore, affordance replaces fixed-eye vision by mobile-eye vision; an active learner establishes relationships with and within the environment. The learner can directly perceive and act on the ambient language without having to route everything through a pre-existing mental apparatus of schemata and representation, while this is not true in the fixed-code theory. In the fixed-eye theory of communication it is assumed that ready-made messages are coded at one end, transmitted,
    and then decoded in identical form at the other end. We need in its place a constructivist theory of message construction and interpretation.

  8. Comparison of sine dwell and broadband methods for modal testing

    Science.gov (United States)

    Chen, Jay-Chung

    1989-01-01

    The objectives of modal tests for large complex spacecraft structural systems are outlined. The comparison criteria for the modal test methods, namely, the broadband excitation and the sine dwell methods, are established. Using the Galileo spacecraft modal test and the Centaur G Prime upper stage vehicle modal test as examples, the relative advantage or disadvantage of each method is examined. The usefulness or shortcomings of the methods are given from a practical engineering viewpoint.

  9. On sine dwell or broadband methods for modal testing

    Science.gov (United States)

    Chen, Jay-Chung; Wada, Ben K.

    1987-01-01

    For large, complex spacecraft structural systems, the objectives of the modal test are outlined. Based on these objectives, the comparison criteria for the modal test methods, namely, the broadband excitation and the sine dwell methods are established. Using the Galileo spacecraft modal test and the Centaur G Prime upper stage vehicle modal test as examples, the relative advantages or disadvantages of each method are examined. The usefulness or shortcoming of the methods are given from a practicing engineer's view point.

  10. Converging modalities ground abstract categories: the case of politics.

    Science.gov (United States)

    Farias, Ana Rita; Garrido, Margarida V; Semin, Gün R

    2013-01-01

    Three studies are reported examining the grounding of abstract concepts across two modalities (visual and auditory) and their symbolic representation. A comparison of the outcomes across these studies reveals that the symbolic representation of political concepts and their visual and auditory modalities is convergent. In other words, the spatial relationships between specific instances of the political categories are highly overlapping across the symbolic, visual and auditory modalities. These findings suggest that abstract categories display redundancy across modal and amodal representations, and are multimodal.

  11. The modality effect of ego depletion: Auditory task modality reduces ego depletion.

    Science.gov (United States)

    Li, Qiong; Wang, Zhenhong

    2016-08-01

    An initial act of self-control that impairs subsequent acts of self-control is called ego depletion. The ego depletion phenomenon has been observed consistently. The modality effect refers to the effect of the presentation modality on the processing of stimuli. The modality effect was also robustly found in a large body of research. However, no study to date has examined the modality effects of ego depletion. This issue was addressed in the current study. In Experiment 1, after all participants completed a handgrip task, one group's participants completed a visual attention regulation task and the other group's participants completed an auditory attention regulation task, and then all participants again completed a handgrip task. The ego depletion phenomenon was observed in both the visual and the auditory attention regulation task. Moreover, participants who completed the visual task performed worse on the handgrip task than participants who completed the auditory task, which indicated that there was high ego depletion in the visual task condition. In Experiment 2, participants completed an initial task that either did or did not deplete self-control resources, and then they completed a second visual or auditory attention control task. The results indicated that depleted participants performed better on the auditory attention control task than the visual attention control task. These findings suggest that altering task modality may reduce ego depletion. © 2016 Scandinavian Psychological Associations and John Wiley & Sons Ltd.

  12. Evidence for a supra-modal representation of emotion from cross-modal adaptation.

    Science.gov (United States)

    Pye, Annie; Bestelmeyer, Patricia E G

    2015-01-01

    Successful social interaction hinges on accurate perception of emotional signals. These signals are typically conveyed multi-modally by the face and voice. Previous research has demonstrated uni-modal contrastive aftereffects for emotionally expressive faces or voices. Here we were interested in whether these aftereffects transfer across modality as theoretical models predict. We show that adaptation to facial expressions elicits significant auditory aftereffects. Adaptation to angry facial expressions caused ambiguous vocal stimuli drawn from an anger-fear morphed continuum to be perceived as less angry and more fearful relative to adaptation to fearful faces. In a second experiment, we demonstrate that these aftereffects are not dependent on learned face-voice congruence, i.e. adaptation to one facial identity transferred to an unmatched voice identity. Taken together, our findings provide support for a supra-modal representation of emotion and suggest further that identity and emotion may be processed independently from one another, at least at the supra-modal level of the processing hierarchy. Copyright © 2014 Elsevier B.V. All rights reserved.

  13. Fuzzy Reasoning Based on First-Order Modal Logic,

    NARCIS (Netherlands)

    Zhang, Xiaoru; Zhang, Z.; Sui, Y.; Huang, Z.

    2008-01-01

    As an extension of traditional modal logics, this paper proposes a fuzzy first-order modal logic based on believable degree, and gives out a description of the fuzzy first-order modal logic based on constant domain semantics. In order to make the reasoning procedure between the fuzzy assertions

  14. The Perceptual Basis of the Modality Effect in Multimedia Learning

    Science.gov (United States)

    Rummer, Ralf; Schweppe, Judith; Furstenberg, Anne; Scheiter, Katharina; Zindler, Antje

    2011-01-01

    Various studies have demonstrated an advantage of auditory over visual text modality when learning with texts and pictures. To explain this modality effect, two complementary assumptions are proposed by cognitive theories of multimedia learning: first, the visuospatial load hypothesis, which explains the modality effect in terms of visuospatial…

  15. Modality effects in implicit artificial grammar learning: An EEG study.

    Science.gov (United States)

    Silva, Susana; Folia, Vasiliki; Inácio, Filomena; Castro, São Luís; Petersson, Karl Magnus

    2018-05-15

    Recently, it has been proposed that sequence learning engages a combination of modality-specific operating networks and modality-independent computational principles. In the present study, we compared the behavioural and EEG outcomes of implicit artificial grammar learning in the visual vs. auditory modality. We controlled for the influence of surface characteristics of sequences (Associative Chunk Strength), thus focusing on the strictly structural aspects of sequence learning, and we adapted the paradigms to compensate for known frailties of the visual modality compared to audition (temporal presentation, fast presentation rate). The behavioural outcomes were similar across modalities. Favouring the idea of modality-specificity, ERPs in response to grammar violations differed in topography and latency (earlier and more anterior component in the visual modality), and ERPs in response to surface features emerged only in the auditory modality. In favour of modality-independence, we observed three common functional properties in the late ERPs of the two grammars: both were free of interactions between structural and surface influences, both were more extended in a grammaticality classification test than in a preference classification test, and both correlated positively and strongly with theta event-related-synchronization during baseline testing. Our findings support the idea of modality-specificity combined with modality-independence, and suggest that memory for visual vs. auditory sequences may largely contribute to cross-modal differences. Copyright © 2018 Elsevier B.V. All rights reserved.

  16. 40 CFR 1033.520 - Alternative ramped modal cycles.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Alternative ramped modal cycles. 1033... cycles. (a) Locomotive testing over a ramped modal cycle is intended to improve measurement accuracy at... locomotive notch settings. Ramped modal cycles combine multiple test modes of a discrete-mode steady-state...

  17. Analytical and experimental comparisons of modal properties of a flood water storage tank

    International Nuclear Information System (INIS)

    Thinnes, G.L.; Dooley, W.T.; Gorman, V.W.

    1986-01-01

    Comparisons of measured frequencies, mode shapes, and damping from experimental modal testing and analytical predictions have been performed on a vertically standing 90,000 liter flood water storage tank. The purpose of the study was to compare the accuracy of analytical calculations with experimentally obtained data. The need for this comparison arises because safety assessments of the integrity of such vessels are normally based upon analyses which have not usually been validated by experiments. The tank was excited using random input from an electromagnetic shaker. Data reduction was performed using frequency response functions. Analyses, including modal analysis calculations, were performed on the tank for three water level conditions using finite element methods. Results of the analyses are presented, comparisons to test data are shown, and conclusions and recommendations are made as a result of these studies. 5 refs., 8 figs., 2 tabs

  18. Modal Analysis of In-Wheel Motor-Driven Electric Vehicle Based on Bond Graph Theory

    Directory of Open Access Journals (Sweden)

    Di Tan

    2017-01-01

    Full Text Available A half-car vibration model of an electric vehicle driven by rear in-wheel motors was developed using bond graph theory and the modular modeling method. Based on the bond graph model, modal analysis was carried out to study the vibration characteristics of the electric vehicle. To verify the effectiveness of the established model, the results were compared to ones computed on the ground of modal analysis and Newton equations. The comparison shows that the vibration model of the electric vehicle based on bond graph theory not only is able to better compute the natural frequency but also can easily determine the deformation mode, momentum mode, and other isomorphism modes and describe the dynamic characteristics of an electric vehicle driven by in-wheel motors more comprehensively than other modal analysis methods.

  19. Ambient modal testing of a double-arch dam: the experimental campaign and model updating

    International Nuclear Information System (INIS)

    García-Palacios, Jaime H.; Soria, José M.; Díaz, Iván M.; Tirado-Andrés, Francisco

    2016-01-01

    A finite element model updating of a double-curvature-arch dam (La Tajera, Spain) is carried out hereof using the modal parameters obtained from an operational modal analysis. That is, the system modal dampings, natural frequencies and mode shapes have been identified using output-only identification techniques under environmental loads (wind, vehicles). A finite element model of the dam-reservoir-foundation system was initially created. Then, a testing campaing was then carried out from the most significant test points using high-sensitivity accelerometers wirelessly synchronized. Afterwards, the model updating of the initial model was done using a Monte Carlo based approach in order to match it to the recorded dynamic behaviour. The updated model may be used within a structural health monitoring system for damage detection or, for instance, for the analysis of the seismic response of the arch dam- reservoir-foundation coupled system. (paper)

  20. Nonlinear model order reduction for flexible multibody dynamics: a modal derivatives approach

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Long, E-mail: L.Wu-1@tudelft.nl [Delft University of Technology, Faculty of Mechanical, Maritime and Materials Engineering (Netherlands); Tiso, Paolo, E-mail: ptiso@ethz.ch [ETH Zürich, Institute for Mechanical Systems (Switzerland)

    2016-04-15

    An effective reduction technique is presented for flexible multibody systems, for which the elastic deflection could not be considered small. We consider here the planar beam systems undergoing large elastic rotations, in the floating frame description. The proposed method enriches the classical linear reduction basis with modal derivatives stemming from the derivative of the eigenvalue problem. Furthermore, the Craig–Bampton method is applied to couple the different reduced components. Based on the linear projection, the configuration-dependent internal force can be expressed as cubic polynomials in the reduced coordinates. Coefficients of these polynomials can be precomputed for efficient runtime evaluation. The numerical results show that the modal derivatives are essential for the correct approximation of the nonlinear elastic deflection with respect to the body reference. The proposed reduction method constitutes a natural and effective extension of the classical linear modal reduction in the floating frame.

  1. Challenges for Preclinical Investigations of Human Biofield Modalities

    Science.gov (United States)

    Gronowicz, Gloria; Bengston, William

    2015-01-01

    Preclinical models for studying the effects of the human biofield have great potential to advance our understanding of human biofield modalities, which include external qigong, Johrei, Reiki, therapeutic touch, healing touch, polarity therapy, pranic healing, and other practices. A short history of Western biofield studies using preclinical models is presented and demonstrates numerous and consistent examples of human biofields significantly affecting biological systems both in vitro and in vivo. Methodological issues arising from these studies and practical solutions in experimental design are presented. Important questions still left unanswered with preclinical models include variable reproducibility, dosing, intentionality of the practitioner, best preclinical systems, and mechanisms. Input from the biofield practitioners in the experimental design is critical to improving experimental outcomes; however, the development of standard criteria for uniformity of practice and for inclusion of multiple practitioners is needed. Research in human biofield studies involving preclinical models promises a better understanding of the mechanisms underlying the efficacy of biofield therapies and will be important in guiding clinical protocols and integrating treatments with conventional medical therapies. PMID:26665042

  2. A pain in the bud? Implications of cross-modal sensitivity for pain experience.

    Science.gov (United States)

    Perkins, Monica; de Bruyne, Marien; Giummarra, Melita J

    2016-11-01

    There is growing evidence that enhanced sensitivity to painful clinical procedures and chronic pain are related to greater sensitivity to other sensory inputs, such as bitter taste. We examined cross-modal sensitivities in two studies. Study 1 assessed associations between bitter taste sensitivity, pain tolerance, and fear of pain in 48 healthy young adults. Participants were classified as non-tasters, tasters and super-tasters using a bitter taste test (6-n-propythiouracil; PROP). The latter group had significantly higher fear of pain (Fear of Pain Questionnaire) than tasters (p=.036, effect size r = .48). There was only a trend for an association between bitter taste intensity ratings and intensity of pain at the point of pain tolerance in a cold pressor test (p=.04). In Study 2, 40 healthy young adults completed the Adolescent/Adult Sensory Profile before rating intensity and unpleasantness of innocuous (33 °C), moderate (41 °C), and high intensity (44 °C) thermal pain stimulations. The sensory-sensitivity subscale was positively correlated with both intensity and unpleasantness ratings. Canonical correlation showed that only sensitivity to audition and touch (not taste/smell) were associated with intensity of moderate and high (not innocuous) thermal stimuli. Together these findings suggest that there are cross-modal associations predominantly between sensitivity to exteroceptive inputs (i.e., taste, touch, sound) and the affective dimensions of pain, including noxious heat and intolerable cold pain, in healthy adults. These cross-modal sensitivities may arise due to greater psychological aversion to salient sensations, or from shared neural circuitry for processing disparate sensory modalities.

  3. READDATA: a FORTRAN 77 codeword input package

    International Nuclear Information System (INIS)

    Lander, P.A.

    1983-07-01

    A new codeword input package has been produced as a result of the incompatibility between different dialects of FORTRAN, especially when character variables are passed as parameters. This report is for those who wish to use a codeword input package with FORTRAN 77. The package, called ''Readdata'', attempts to combine the best features of its predecessors such as BINPUT and pseudo-BINPUT. (author)

  4. CREATING INPUT TABLES FROM WAPDEG FOR RIP

    International Nuclear Information System (INIS)

    K.G. Mon

    1998-01-01

    The purpose of this calculation is to create tables for input into RIP ver. 5.18 (Integrated Probabilistic Simulator for Environmental Systems) from WAPDEG ver. 3.06 (Waste Package Degradation) output. This calculation details the creation of the RIP input tables for TSPA-VA REV.00

  5. Wave energy input into the Ekman layer

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    This paper is concerned with the wave energy input into the Ekman layer, based on 3 observational facts that surface waves could significantly affect the profile of the Ekman layer. Under the assumption of constant vertical diffusivity, the analytical form of wave energy input into the Ekman layer is derived. Analysis of the energy balance shows that the energy input to the Ekman layer through the wind stress and the interaction of the Stokes-drift with planetary vorticity can be divided into two kinds. One is the wind energy input, and the other is the wave energy input which is dependent on wind speed, wave characteristics and the wind direction relative to the wave direction. Estimates of wave energy input show that wave energy input can be up to 10% in high-latitude and high-wind speed areas and higher than 20% in the Antarctic Circumpolar Current, compared with the wind energy input into the classical Ekman layer. Results of this paper are of significance to the study of wave-induced large scale effects.

  6. Input Enhancement and L2 Question Formation.

    Science.gov (United States)

    White, Lydia; And Others

    1991-01-01

    Investigated the extent to which form-focused instruction and corrective feedback (i.e., "input enhancement"), provided within a primarily communicative program, contribute to learners' accuracy in question formation. Study results are interpreted as evidence that input enhancement can bring about genuine changes in learners' interlanguage…

  7. Using experimental modal analysis to assess the behaviour of timber elements

    Science.gov (United States)

    Kouroussis, Georges; Fekih, Lassaad Ben; Descamps, Thierry

    2018-03-01

    Timber frameworks are one of the most important and widespread types of structures. Their configurations and joints are usually complex and require a high level of craftsmanship to assemble. In the field of restoration, a good understanding of the structural behaviour is necessary and is often based on assessment techniques dedicated to wood characterisation. This paper presents the use of experimental modal analysis for finite element updating. To do this, several timber beams in a free supported condition were analysed in order to extract their bending natural characteristics (frequency, damping and mode shapes). Corresponding ABAQUS finite element models were derived which included the effects of local defects (holes, cracks and wood nodes), moisture and structural decay. To achieve the modal updating, additional simulations were performed in order to study the sensitivity of the mechanical parameters. With the intent to estimate their mechanical properties, a procedure of modal updating was carried out in MatLab with a Python script. This was created to extract the modal information from the ABAQUS modal analysis results to be compared with the experimental results. The updating was based on a minimum of unconstrained multivariable function using a derivative-free method. The objective function was selected from the conventional comparison tools (absolute or relative frequency difference, and/or modal assurance criterion). This testing technique was used to determine the dynamic mechanical properties of timber beams, such as the anisotropic Young's Moduli and damping ratio. To verify the modulus, a series of static 4-point bending tests and STS04 classifications were conducted. The results also revealed that local defects have a negligible influence on natural frequencies. The results demonstrate that this assessment tool offers an effective method to obtain the mechanical properties of timber elements, especially when on-site and non-destructive techniques are

  8. Perception of Scenes in Different Sensory Modalities: A Result of Modal Completion.

    Science.gov (United States)

    Gruber, Ronald R; Block, Richard A

    2017-01-01

    Dynamic perception includes amodal and modal completion, along with apparent movement. It fills temporal gaps for single objects. In 2 experiments, using 6 stimulus presentation conditions involving 3 sensory modalities, participants experienced 8-10 sequential stimuli (200 ms each) with interstimulus intervals (ISIs) of 0.25-7.0 s. Experiments focused on spatiotemporal completion (walking), featural completion (object changing), auditory, completion (falling bomb), and haptic changes (insect crawling). After each trial, participants judged whether they experienced the process of "happening " or whether they simply knew that the process must have occurred. The phenomenon was frequency independent, being reported at short ISIs but not at long ISIs. The phenomenon involves dynamic modal completion and possibly also conceptual processes.

  9. Modality-specificity of Selective Attention Networks.

    Science.gov (United States)

    Stewart, Hannah J; Amitay, Sygal

    2015-01-01

    To establish the modality specificity and generality of selective attention networks. Forty-eight young adults completed a battery of four auditory and visual selective attention tests based upon the Attention Network framework: the visual and auditory Attention Network Tests (vANT, aANT), the Test of Everyday Attention (TEA), and the Test of Attention in Listening (TAiL). These provided independent measures for auditory and visual alerting, orienting, and conflict resolution networks. The measures were subjected to an exploratory factor analysis to assess underlying attention constructs. The analysis yielded a four-component solution. The first component comprised of a range of measures from the TEA and was labeled "general attention." The third component was labeled "auditory attention," as it only contained measures from the TAiL using pitch as the attended stimulus feature. The second and fourth components were labeled as "spatial orienting" and "spatial conflict," respectively-they were comprised of orienting and conflict resolution measures from the vANT, aANT, and TAiL attend-location task-all tasks based upon spatial judgments (e.g., the direction of a target arrow or sound location). These results do not support our a-priori hypothesis that attention networks are either modality specific or supramodal. Auditory attention separated into selectively attending to spatial and non-spatial features, with the auditory spatial attention loading onto the same factor as visual spatial attention, suggesting spatial attention is supramodal. However, since our study did not include a non-spatial measure of visual attention, further research will be required to ascertain whether non-spatial attention is modality-specific.

  10. Modality-specificity of selective attention networks

    Directory of Open Access Journals (Sweden)

    Hannah Jamieson Stewart

    2015-11-01

    Full Text Available Objective: To establish the modality specificity and generality of selective attention networks. Method: Forty-eight young adults completed a battery of four auditory and visual selective attention tests based upon the Attention Network framework: the visual and auditory Attention Network Tests (vANT, aANT, the Test of Everyday Attention (TEA, and the Test of Attention in Listening (TAiL. These provided independent measures for auditory and visual alerting, orienting, and conflict resolution networks. The measures were subjected to an exploratory factor analysis to assess underlying attention constructs. Results: The analysis yielded a four-component solution. The first component comprised of a range of measures from the TEA and was labeled ‘general attention’. The third component was labeled ‘auditory attention’, as it only contained measures from the TAiL using pitch as the attended stimulus feature. The second and fourth components were labeled as ‘spatial orienting’ and ‘spatial conflict’, respectively – they were comprised of orienting and conflict resolution measures from the vANT, aANT and TAiL attend-location task – all tasks based upon spatial judgments (e.g., the direction of a target arrow or sound location. Conclusions: These results do not support our a-priori hypothesis that attention networks are either modality specific or supramodal. Auditory attention separated into selectively attending to spatial and non-spatial features, with the auditory spatial attention loading onto the same factor as visual spatial attention, suggesting spatial attention is supramodal. However, since our study did not include a non-spatial measure of visual attention, further research will be required to ascertain whether non-spatial attention is modality-specific.

  11. Water as an Independent Taste Modality

    Directory of Open Access Journals (Sweden)

    Andrew M Rosen

    2010-10-01

    Full Text Available To qualify as a basic taste quality or modality, defined as a group of chemicals that taste alike, three empirical benchmarks have commonly been used. The first is that a candidate group of tastants must have a dedicated transduction mechanism in the peripheral nervous system. The second is that the tastants evoke physiological responses in dedicated afferent taste nerves innervating the oropharyngeal cavity. Last, the taste stimuli evoke activity in central gustatory neurons, some of which may respond only to that group of tastants. Here we argue that water may also be an independent taste modality. This argument is based on the identification of a water dedicated transduction mechanism in the peripheral nervous system, water responsive fibers of the peripheral taste nerves and the observation of water responsive neurons in all gustatory regions within the central nervous system. We have described electrophysiological responses from single neurons in nucleus of the solitary tract (NTS and parabrachial nucleus of the pons (PbN, respectively the first two central relay nuclei in the rodent brainstem, to water presented as a taste stimulus in anesthetized rats. Responses to water were in some cases as robust as responses to other taste qualities and sometimes occurred in the absence of responses to other tastants. Both excitatory and inhibitory responses were observed. Also, the temporal features of the water response resembled those of other taste responses. We argue that water may constitute an independent taste modality that is processed by dedicated neural channels at all levels of the gustatory neuraxis. Water-dedicated neurons in the brainstem may constitute key elements in the regulatory system for fluid in the body, i.e. thirst, and as part of the swallowing reflex circuitry.

  12. Man versus machine: the preferred modality.

    Science.gov (United States)

    Sanko, Jill; Shekhter, Ilya; Rosen, Lisa; Arheart, Kristopher; Birnbach, David

    2012-12-01

    When learning objectives do not specifically dictate the use of one simulation modality over another, we sought to answer the question of which modality is preferred. We also assessed the impact of debriefing, and the frequency of participants asserting their leadership, as well as self-reported comfort and competence, and the ability to generate differential diagnoses when either a standardised patient (SP) or high-technology simulator (HTS) was used. One hundred and forty medical students participated in a simulation-based activity focusing on teamwork, task delegation, role clarity and effective communication. Two similar clinical scenarios were presented, and either an HTS or an SP was used. Following each scenario, participants were surveyed on the realism of the simulation and the patient, and also on their self-assessed comfort and competence. They were also asked to indicate which role they played, to list possible differential diagnoses for the case and, following the second scenario, which modality they preferred. The surveys indicated that 91 per cent (127) of students preferred the SP. The perceived realism of the simulation was higher for the second scenario than for the first. Scenarios with an SP were found to be significantly more realistic than the scenarios where the HTS was used. Comfort and competence scores were higher following the second scenario. No differences in the ability of participants to generate a list of differentials were found, and nearly twice as many participants reported taking the leadership role during their second simulation. We have found low and high technology to have similar effectiveness for achieving learning objectives and for the demonstration of skills; however, students clearly preferred the SPs. © Blackwell Publishing Ltd 2012.

  13. Modal Identification in an Automotive Multi-Component System Using HS 3D-DIC

    Directory of Open Access Journals (Sweden)

    Ángel Jesús Molina-Viedma

    2018-02-01

    Full Text Available The modal characterization of automotive lighting systems becomes difficult using sensors due to the light weight of the elements which compose the component as well as the intricate access to allocate them. In experimental modal analysis, high speed 3D digital image correlation (HS 3D-DIC is attracting the attention since it provides full-field contactless measurements of 3D displacements as main advantage over other techniques. Different methodologies have been published that perform modal identification, i.e., natural frequencies, damping ratios, and mode shapes using the full-field information. In this work, experimental modal analysis has been performed in a multi-component automotive lighting system using HS 3D-DIC. Base motion excitation was applied to simulate operating conditions. A recently validated methodology has been employed for modal identification using transmissibility functions, i.e., the transfer functions from base motion tests. Results make it possible to identify local and global behavior of the different elements of injected polymeric and metallic materials.

  14. Modal Identification in an Automotive Multi-Component System Using HS 3D-DIC

    Science.gov (United States)

    López-Alba, Elías; Felipe-Sesé, Luis; Díaz, Francisco A.

    2018-01-01

    The modal characterization of automotive lighting systems becomes difficult using sensors due to the light weight of the elements which compose the component as well as the intricate access to allocate them. In experimental modal analysis, high speed 3D digital image correlation (HS 3D-DIC) is attracting the attention since it provides full-field contactless measurements of 3D displacements as main advantage over other techniques. Different methodologies have been published that perform modal identification, i.e., natural frequencies, damping ratios, and mode shapes using the full-field information. In this work, experimental modal analysis has been performed in a multi-component automotive lighting system using HS 3D-DIC. Base motion excitation was applied to simulate operating conditions. A recently validated methodology has been employed for modal identification using transmissibility functions, i.e., the transfer functions from base motion tests. Results make it possible to identify local and global behavior of the different elements of injected polymeric and metallic materials. PMID:29401725

  15. Modal Identification in an Automotive Multi-Component System Using HS 3D-DIC.

    Science.gov (United States)

    Molina-Viedma, Ángel Jesús; López-Alba, Elías; Felipe-Sesé, Luis; Díaz, Francisco A

    2018-02-05

    The modal characterization of automotive lighting systems becomes difficult using sensors due to the light weight of the elements which compose the component as well as the intricate access to allocate them. In experimental modal analysis, high speed 3D digital image correlation (HS 3D-DIC) is attracting the attention since it provides full-field contactless measurements of 3D displacements as main advantage over other techniques. Different methodologies have been published that perform modal identification, i.e., natural frequencies, damping ratios, and mode shapes using the full-field information. In this work, experimental modal analysis has been performed in a multi-component automotive lighting system using HS 3D-DIC. Base motion excitation was applied to simulate operating conditions. A recently validated methodology has been employed for modal identification using transmissibility functions, i.e., the transfer functions from base motion tests. Results make it possible to identify local and global behavior of the different elements of injected polymeric and metallic materials.

  16. A Modal Logic for Termgraph Rewriting

    OpenAIRE

    Balbiani, Ph.; Echahed, R.; Herzig, A.

    2010-01-01

    We propose a modal logic tailored to describe graph transformations and discuss some of its properties. We focus on a particular class of graphs called termgraphs. They are first-order terms augmented with sharing and cycles. Termgraphs allow one to describe classical data-structures (possibly with pointers) such as doubly-linked lists, circular lists etc. We show how the proposed logic can faithfully describe (i) termgraphs as well as (ii) the application of a termgraph rewrite rule (i.e. ma...

  17. Modal decomposition without a priori scale information

    CSIR Research Space (South Africa)

    Schulze, C

    2012-12-01

    Full Text Available , and A. Friberg, ?Transverse laser mode structure determination from spatial coherence measurements: Experimental results,? Appl. Phys. B. 49, 409?414 (1989). 4. A. Cutolo, T. Isernia, I. Izzo, R. Pierri, and L. Zeni, ?Transverse mode analysis of a... laser beam by near-and far-field intensity measurements,? Appl. Opt. 34, 7974?7978 (1995). 5. M. Santarsiero, F. Gori, R. Borghi, and G. Guattari, ?Evaluation of the modal structure of light beams composed of incoherent mixtures of hermite...

  18. On Determinism in Modal Transition Systems

    DEFF Research Database (Denmark)

    Benes, Nikola; Kretinsky, Jan; Larsen, Kim Guldstrand

    2009-01-01

    Modal transition systems (MTS) is a formalism which extends the classical notion of labelled transition systems by introducing transitions of two types: must transitions that have to be present in any implementation of the MTS and may transitions that are allowed but not required. The MTS framewo....... In the present article, we provide a comprehensive account of the MTS framework in the deterministic setting. We study a number of problems previously considered on MTS and point out to what extend we can expect better results under the restriction of determinism....

  19. Shoulder distention arthrography as a treatment modality

    International Nuclear Information System (INIS)

    Kang, Heung Sik; Park, Chan Sup; Kim, Jin Ho; Kim, Sang Bum

    1987-01-01

    18 patients with painful stiff shoulder joint were underwent shoulder distension arthrography as a treatment modality, followed by physical therapy. Range of motion of shoulder joint was evaluated at 1 week and 4 weeks after arthrography. The results were as follows; 1. Arthrographic findings were decreased volume of joint cavity, obliteration of axillary recess, small subscapularis bursa, serrated capsular margin and non-filling of biceps tendon sheath. In 3 cases, rotator cuff tear was found. 2. Range of motion of shoulder joint was improved after distension arthrography. 3. In 3 patients have rotator cuff tear, range of motion was not improved

  20. Development of Hardware Dual Modality Tomography System

    Directory of Open Access Journals (Sweden)

    R. M. Zain

    2009-06-01

    Full Text Available The paper describes the hardware development and performance of the Dual Modality Tomography (DMT system. DMT consists of optical and capacitance sensors. The optical sensors consist of 16 LEDs and 16 photodiodes. The Electrical Capacitance Tomography (ECT electrode design use eight electrode plates as the detecting sensor. The digital timing and the control unit have been developing in order to control the light projection of optical emitters, switching the capacitance electrodes and to synchronize the operation of data acquisition. As a result, the developed system is able to provide a maximum 529 set data per second received from the signal conditioning circuit to the computer.

  1. Diagnostic Approach in Impotence and Imaging Modalities

    Directory of Open Access Journals (Sweden)

    Medih Celiktas

    2015-06-01

    Full Text Available Penile erection results from a complex interplay between central nerveus system and local factors. Several aspects of these interactions have been the subject of many reviews. Nocturnal penile tumescence (NPT monitoring is the best single non-invasive examination to differentiate organic from psychogenic impotence. Angiography and pharmaco-cevernosometry are accepted as gold standard modalities in the assesment of vasculojenic impotence. Recently color Doppler sonography made the detection of vessels easier and the correction of the Doppler angle more accurate, resulting in more rapid and accurate acquisition of data. [Cukurova Med J 2015; 40(2.000: 208-211

  2. Statistical identification of effective input variables

    International Nuclear Information System (INIS)

    Vaurio, J.K.

    1982-09-01

    A statistical sensitivity analysis procedure has been developed for ranking the input data of large computer codes in the order of sensitivity-importance. The method is economical for large codes with many input variables, since it uses a relatively small number of computer runs. No prior judgemental elimination of input variables is needed. The sceening method is based on stagewise correlation and extensive regression analysis of output values calculated with selected input value combinations. The regression process deals with multivariate nonlinear functions, and statistical tests are also available for identifying input variables that contribute to threshold effects, i.e., discontinuities in the output variables. A computer code SCREEN has been developed for implementing the screening techniques. The efficiency has been demonstrated by several examples and applied to a fast reactor safety analysis code (Venus-II). However, the methods and the coding are general and not limited to such applications

  3. Gestural Communication With Accelerometer-Based Input Devices and Tactile Displays

    Science.gov (United States)

    2008-12-01

    and natural terrain obstructions, or concealment often impede visual communication attempts. To overcome some of these issues, “daisy-chaining” or...the intended recipients. Moreover, visual communication demands a focus on the visual modality possibly distracting a receiving soldier’s visual

  4. Modal Testing of Mechanical Structures Subject to Operational Excitation Forces

    DEFF Research Database (Denmark)

    Møller, N.; Brincker, Rune; Herlufsen, H.

    2000-01-01

    to the Operational Modal Analysis. For Operational Modal Analysis two different estimation techniques are used: a non-parametric technique based on Frequency Domain Decomposition (FDD), and a parametric technique working on the raw data in time domain, a data driven Stochastic Subspace Identification (SSI) algorithm......Operational Modal Analysis also known as Output Only Modal Analysis has in the recent years been used for extracting modal parameters of civil engineering structures and is now becoming popular for mechanical structures. The advantage of the method is that no artificial excitation need...

  5. Measuring Input Thresholds on an Existing Board

    Science.gov (United States)

    Kuperman, Igor; Gutrich, Daniel G.; Berkun, Andrew C.

    2011-01-01

    A critical PECL (positive emitter-coupled logic) interface to Xilinx interface needed to be changed on an existing flight board. The new Xilinx input interface used a CMOS (complementary metal-oxide semiconductor) type of input, and the driver could meet its thresholds typically, but not in worst-case, according to the data sheet. The previous interface had been based on comparison with an external reference, but the CMOS input is based on comparison with an internal divider from the power supply. A way to measure what the exact input threshold was for this device for 64 inputs on a flight board was needed. The measurement technique allowed an accurate measurement of the voltage required to switch a Xilinx input from high to low for each of the 64 lines, while only probing two of them. Directly driving an external voltage was considered too risky, and tests done on any other unit could not be used to qualify the flight board. The two lines directly probed gave an absolute voltage threshold calibration, while data collected on the remaining 62 lines without probing gave relative measurements that could be used to identify any outliers. The PECL interface was forced to a long-period square wave by driving a saturated square wave into the ADC (analog to digital converter). The active pull-down circuit was turned off, causing each line to rise rapidly and fall slowly according to the input s weak pull-down circuitry. The fall time shows up as a change in the pulse width of the signal ready by the Xilinx. This change in pulse width is a function of capacitance, pulldown current, and input threshold. Capacitance was known from the different trace lengths, plus a gate input capacitance, which is the same for all inputs. The pull-down current is the same for all inputs including the two that are probed directly. The data was combined, and the Excel solver tool was used to find input thresholds for the 62 lines. This was repeated over different supply voltages and

  6. Emerging Biometric Modalities: Challenges and Opportunities

    Science.gov (United States)

    Gafurov, Davrondzhon

    Recent advances in sensor technology and wide spread use of various electronics (computers, PDA, mobile phones etc.) provide new opportunities for capturing and analyses of novel physiological and behavioural traits of human beings for biometric authentication. This paper presents an overview of several such types of human characteristics that have been proposed as alternatives to traditional types of biometrics. We refer to these characteristics as emerging biometrics. We survey various types of emerging modalities and techniques, and discuss their pros and cons. Emerging biometrics faces several limitations and challenges which include subject population coverage (focusing mostly on adults); unavailability of benchmark databases; little research with respect to vulnerability/robustness against attacks; and some privacy concerns they may arise. In addition, recognition performance of emerging modalities are generally less accurate compared to the traditional biometrics. Despite all of these emerging biometrics posses their own benefits and advantages compared to traditional biometrics which makes them still attractive for research. First of all, emerging biometrics can always serve as a complementary source for identity information; they can be suitable in applications where traditional biometrics are difficult or impossible to adapt such as continuous or periodic re-verification of the user's identity etc.

  7. Approximate modal analysis using Fourier decomposition

    International Nuclear Information System (INIS)

    Kozar, Ivica; Jericevic, Zeljko; Pecak, Tatjana

    2010-01-01

    The paper presents a novel numerical approach for approximate solution of eigenvalue problem and investigates its suitability for modal analysis of structures with special attention on plate structures. The approach is based on Fourier transformation of the matrix equation into frequency domain and subsequent removal of potentially less significant frequencies. The procedure results in a much reduced problem that is used in eigenvalue calculation. After calculation eigenvectors are expanded and transformed back into time domain. The principles are presented in Jericevic [1]. Fourier transform can be formulated in a way that some parts of the matrix that should not be approximated are not transformed but are fully preserved. In this paper we present formulation that preserves central or edge parts of the matrix and compare it with the formulation that performs transform on the whole matrix. Numerical experiments on transformed structural dynamic matrices describe quality of the approximations obtained in modal analysis of structures. On the basis of the numerical experiments, from the three approaches to matrix reduction one is recommended.

  8. Pathogenesis and treatment modalities of localized scleroderma.

    Science.gov (United States)

    Valančienė, Greta; Jasaitienė, Daiva; Valiukevičienė, Skaidra

    2010-01-01

    Localized scleroderma is a chronic inflammatory disease primarily of the dermis and subcutaneous fat that ultimately leads to a scar-like sclerosis of connective tissue. The disorder manifests as various plaques of different shape and size with signs of skin inflammation, sclerosis, and atrophy. This is a relatively rare inflammatory disease characterized by a chronic course, unknown etiology, and insufficiently clear pathogenesis. Many factors may influence its appearance: trauma, genetic factors, disorders of the immune system or hormone metabolism, viral infections, toxic substances or pharmaceutical agents, neurogenic factors, and Borrelia burgdorferi infection. Various therapeutic modalities are being used for the treatment of localized scleroderma. There is no precise treatment scheme for this disease. A majority of patients can be successfully treated with topical pharmaceutical agents and phototherapy, but some of them with progressive, disseminated, and causing disability localized scleroderma are in need of systemic treatment. The aim of this article is not only to dispute about the clinical and morphological characteristics of localized scleroderma, but also to present the newest generalized data about the possible origin, pathogenesis, and treatment modalities of this disease.

  9. Wearable sensors: modalities, challenges, and prospects.

    Science.gov (United States)

    Heikenfeld, J; Jajack, A; Rogers, J; Gutruf, P; Tian, L; Pan, T; Li, R; Khine, M; Kim, J; Wang, J; Kim, J

    2018-01-16

    Wearable sensors have recently seen a large increase in both research and commercialization. However, success in wearable sensors has been a mix of both progress and setbacks. Most of commercial progress has been in smart adaptation of existing mechanical, electrical and optical methods of measuring the body. This adaptation has involved innovations in how to miniaturize sensing technologies, how to make them conformal and flexible, and in the development of companion software that increases the value of the measured data. However, chemical sensing modalities have experienced greater challenges in commercial adoption, especially for non-invasive chemical sensors. There have also been significant challenges in making significant fundamental improvements to existing mechanical, electrical, and optical sensing modalities, especially in improving their specificity of detection. Many of these challenges can be understood by appreciating the body's surface (skin) as more of an information barrier than as an information source. With a deeper understanding of the fundamental challenges faced for wearable sensors and of the state-of-the-art for wearable sensor technology, the roadmap becomes clearer for creating the next generation of innovations and breakthroughs.

  10. Timescale- and Sensory Modality-Dependency of the Central Tendency of Time Perception.

    Science.gov (United States)

    Murai, Yuki; Yotsumoto, Yuko

    2016-01-01

    When individuals are asked to reproduce intervals of stimuli that are intermixedly presented at various times, longer intervals are often underestimated and shorter intervals overestimated. This phenomenon may be attributed to the central tendency of time perception, and suggests that our brain optimally encodes a stimulus interval based on current stimulus input and prior knowledge of the distribution of stimulus intervals. Two distinct systems are thought to be recruited in the perception of sub- and supra-second intervals. Sub-second timing is subject to local sensory processing, whereas supra-second timing depends on more centralized mechanisms. To clarify the factors that influence time perception, the present study investigated how both sensory modality and timescale affect the central tendency. In Experiment 1, participants were asked to reproduce sub- or supra-second intervals, defined by visual or auditory stimuli. In the sub-second range, the magnitude of the central tendency was significantly larger for visual intervals compared to auditory intervals, while visual and auditory intervals exhibited a correlated and comparable central tendency in the supra-second range. In Experiment 2, the ability to discriminate sub-second intervals in the reproduction task was controlled across modalities by using an interval discrimination task. Even when the ability to discriminate intervals was controlled, visual intervals exhibited a larger central tendency than auditory intervals in the sub-second range. In addition, the magnitude of the central tendency for visual and auditory sub-second intervals was significantly correlated. These results suggest that a common modality-independent mechanism is responsible for the supra-second central tendency, and that both the modality-dependent and modality-independent components of the timing system contribute to the central tendency in the sub-second range.

  11. Timescale- and Sensory Modality-Dependency of the Central Tendency of Time Perception.

    Directory of Open Access Journals (Sweden)

    Yuki Murai

    Full Text Available When individuals are asked to reproduce intervals of stimuli that are intermixedly presented at various times, longer intervals are often underestimated and shorter intervals overestimated. This phenomenon may be attributed to the central tendency of time perception, and suggests that our brain optimally encodes a stimulus interval based on current stimulus input and prior knowledge of the distribution of stimulus intervals. Two distinct systems are thought to be recruited in the perception of sub- and supra-second intervals. Sub-second timing is subject to local sensory processing, whereas supra-second timing depends on more centralized mechanisms. To clarify the factors that influence time perception, the present study investigated how both sensory modality and timescale affect the central tendency. In Experiment 1, participants were asked to reproduce sub- or supra-second intervals, defined by visual or auditory stimuli. In the sub-second range, the magnitude of the central tendency was significantly larger for visual intervals compared to auditory intervals, while visual and auditory intervals exhibited a correlated and comparable central tendency in the supra-second range. In Experiment 2, the ability to discriminate sub-second intervals in the reproduction task was controlled across modalities by using an interval discrimination task. Even when the ability to discriminate intervals was controlled, visual intervals exhibited a larger central tendency than auditory intervals in the sub-second range. In addition, the magnitude of the central tendency for visual and auditory sub-second intervals was significantly correlated. These results suggest that a common modality-independent mechanism is responsible for the supra-second central tendency, and that both the modality-dependent and modality-independent components of the timing system contribute to the central tendency in the sub-second range.

  12. Simulation of Single Reed Instruments Oscillations Based on Modal Decomposition of Bore and Reed Dynamics

    OpenAIRE

    Silva, Fabrice; Debut, Vincent; Kergomard, Jean; Vergez, Christophe; Deblevid, Aude; Guillemain, Philippe

    2007-01-01

    This paper investigates the sound production in a system made of a bore coupled with a reed valve. Extending previous work (Debut, 2004), the input impedance of the bore is projected on the modes of the air column. The acoustic pressure is therefore calculated as the sum of modal components. The airrrflow blown into the bore is modulated by reed motion, assuming the reed to be a single degree of freedom oscillator. Calculation of self-sustained oscillations controlled by time-varyi...

  13. MARS code manual volume II: input requirements

    International Nuclear Information System (INIS)

    Chung, Bub Dong; Kim, Kyung Doo; Bae, Sung Won; Jeong, Jae Jun; Lee, Seung Wook; Hwang, Moon Kyu

    2010-02-01

    Korea Advanced Energy Research Institute (KAERI) conceived and started the development of MARS code with the main objective of producing a state-of-the-art realistic thermal hydraulic systems analysis code with multi-dimensional analysis capability. MARS achieves this objective by very tightly integrating the one dimensional RELAP5/MOD3 with the multi-dimensional COBRA-TF codes. The method of integration of the two codes is based on the dynamic link library techniques, and the system pressure equation matrices of both codes are implicitly integrated and solved simultaneously. In addition, the Equation-Of-State (EOS) for the light water was unified by replacing the EOS of COBRA-TF by that of the RELAP5. This input manual provides a complete list of input required to run MARS. The manual is divided largely into two parts, namely, the one-dimensional part and the multi-dimensional part. The inputs for auxiliary parts such as minor edit requests and graph formatting inputs are shared by the two parts and as such mixed input is possible. The overall structure of the input is modeled on the structure of the RELAP5 and as such the layout of the manual is very similar to that of the RELAP. This similitude to RELAP5 input is intentional as this input scheme will allow minimum modification between the inputs of RELAP5 and MARS3.1. MARS3.1 development team would like to express its appreciation to the RELAP5 Development Team and the USNRC for making this manual possible

  14. Total dose induced increase in input offset voltage in JFET input operational amplifiers

    International Nuclear Information System (INIS)

    Pease, R.L.; Krieg, J.; Gehlhausen, M.; Black, J.

    1999-01-01

    Four different types of commercial JFET input operational amplifiers were irradiated with ionizing radiation under a variety of test conditions. All experienced significant increases in input offset voltage (Vos). Microprobe measurement of the electrical characteristics of the de-coupled input JFETs demonstrates that the increase in Vos is a result of the mismatch of the degraded JFETs. (authors)

  15. Does the Modality Effect Exist? And if so, Which Modality Effect?

    Science.gov (United States)

    Reinwein, Joachim

    2012-01-01

    The modality effect is a central issue in multimedia learning [see Mayer (Cambridge University Press, 2005a), for a review]. Sweller's Cognitive Load Theory (CLT), for example, presumes that an illustrated text is better understood when presented visually rather than orally. The predictive power of CLT lies in how it links in to Baddeley's (1986)…

  16. Supervised Cross-Modal Factor Analysis for Multiple Modal Data Classification

    KAUST Repository

    Wang, Jingbin; Zhou, Yihua; Duan, Kanghong; Wang, Jim Jing-Yan; Bensmail, Halima

    2015-01-01

    . In this paper, we improve CFA by incorporating the supervision information to represent and classify both image and text modals of documents. We project both image and text data to a shared data space by factor analysis, and then train a class label predictor

  17. A Modal Approach to Compact MIMO Antenna Design

    Science.gov (United States)

    Yang, Binbin

    MIMO (Multiple-Input Multiple-Output) technology offers new possibilities for wireless communication through transmission over multiple spatial channels, and enables linear increases in spectral efficiency as the number of the transmitting and receiving antennas increases. However, the physical implementation of such systems in compact devices encounters many physical constraints mainly from the design of multi-antennas. First, an antenna's bandwidth decreases dramatically as its electrical size reduces, a fact known as antenna Q limit; secondly, multiple antennas closely spaced tend to couple with each other, undermining MIMO performance. Though different MIMO antenna designs have been proposed in the literature, there is still a lack of a systematic design methodology and knowledge of performance limits. In this dissertation, we employ characteristic mode theory (CMT) as a powerful tool for MIMO antenna analysis and design. CMT allows us to examine each physical mode of the antenna aperture, and to access its many physical parameters without even exciting the antenna. For the first time, we propose efficient circuit models for MIMO antennas of arbitrary geometry using this modal decomposition technique. Those circuit models demonstrate the powerful physical insight of CMT for MIMO antenna modeling, and simplify MIMO antenna design problem to just the design of specific antenna structural modes and a modal feed network, making possible the separate design of antenna aperture and feeds. We therefore develop a feed-independent shape synthesis technique for optimization of broadband multi-mode apertures. Combining the shape synthesis and circuit modeling techniques for MIMO antennas, we propose a shape-first feed-next design methodology for MIMO antennas, and designed and fabricated two planar MIMO antennas, each occupying an aperture much smaller than the regular size of lambda/2 x lambda/2. Facilitated by the newly developed source formulation for antenna stored

  18. Modal analysis by holographic interferometry of a turbine blade for aircraft engines

    Science.gov (United States)

    Caponero, Michele A.; De Angelis, Alberto; Filetti, V. R.; Gammella, S.

    1994-11-01

    Within the planning stage devoted to realize an innovative turbine for an aircraft engine, an experimental prototype has been made. Several measurements have been carried out to experimentally verify the expected structural and dynamic features of such a prototype. Expected properties were worked out by finite elements method, using the well-known Nastran software package. Natural frequencies and vibration modes of the designed prototype were computed assuming the turbine being in both `dynamic condition' (rotating turbine at running speed and temperature), and in `static condition' (still turbine at room temperature). We present the experimental modal analysis carried out by time average holographic interferometry, being the prototype in `static condition;' results show the modal behavior of the prototype. Experimental and computed modal features are compared to evaluate the reliability of the finite elements model of the turbine used for computation by the Nastran package; reliability of the finite elements model must be checked to validate results computed assuming the turbine blade is in hostile environments, such as `dynamic condition,' which could hardly be tested by experimental measurements. A piezoelectric transducer was used to excite the turbine blade by sine variable pressure. To better estimate the natural vibration modes, two holographic interferograms have been made for each identified natural frequency, being the sensitivity vector directions of the two interferograms perpendicular to each other. The first ten lower natural frequencies and vibration modes of the blade have been analyzed; experimental and computed results are compared and discussed. Experimental and computed values of natural frequencies are in good agrement between each other. Several differences are present between experimental and computed modal patterns; a possible cause of such discrepancies is identified in wrong structural constraints imposed at nodes of the finite elements

  19. Automatic vibration mode selection and excitation; combining modal filtering with autoresonance

    Science.gov (United States)

    Davis, Solomon; Bucher, Izhak

    2018-02-01

    Autoresonance is a well-known nonlinear feedback method used for automatically exciting a system at its natural frequency. Though highly effective in exciting single degree of freedom systems, in its simplest form it lacks a mechanism for choosing the mode of excitation when more than one is present. In this case a single mode will be automatically excited, but this mode cannot be chosen or changed. In this paper a new method for automatically exciting a general second-order system at any desired natural frequency using Autoresonance is proposed. The article begins by deriving a concise expression for the frequency of the limit cycle induced by an Autoresonance feedback loop enclosed on the system. The expression is based on modal decomposition, and provides valuable insight into the behavior of a system controlled in this way. With this expression, a method for selecting and exciting a desired mode naturally follows by combining Autoresonance with Modal Filtering. By taking various linear combinations of the sensor signals, by orthogonality one can "filter out" all the unwanted modes effectively. The desired mode's natural frequency is then automatically reflected in the limit cycle. In experiment the technique has proven extremely robust, even if the amplitude of the desired mode is significantly smaller than the others and the modal filters are greatly inaccurate.

  20. Comparison of the Time Domain Windows Specified in the ISO 18431 Standards Used to Estimate Modal Parameters in Steel Plates

    Directory of Open Access Journals (Sweden)

    Jhonatan Camacho-Navarro

    2016-01-01

    Full Text Available The procedures used to estimate structural modal parameters as natural frequency, damping ratios, and mode shapes are generally based on frequency methods. However, methods of time-frequency analysis are highly sensible to the parameters used to calculate the discrete Fourier transform: windowing, resolution, and preprocessing. Thus, the uncertainty of the modal parameters is increased if a proper parameter selection is not considered. In this work, the influence of three different time domain windows functions (Hanning, flat-top, and rectangular used to estimate modal parameters are discussed in the framework of ISO 18431 standard. Experimental results are conducted over an AISI 1020 steel plate, which is excited by means of a hammer element. Vibration response is acquired by using acceleration records according to the ISO 7626-5 reference guides. The results are compared with a theoretical method and it is obtained that the flat-top window is the best function for experimental modal analysis.

  1. Input-output rearrangement of isolated converters

    DEFF Research Database (Denmark)

    Madsen, Mickey Pierre; Kovacevic, Milovan; Mønster, Jakob Døllner

    2015-01-01

    This paper presents a new way of rearranging the input and output of isolated converters. The new arrangement posses several advantages, as increased voltage range, higher power handling capabilities, reduced voltage stress and improved efficiency, for applications where galvanic isolation...

  2. Multiple Input - Multiple Output (MIMO) SAR

    Data.gov (United States)

    National Aeronautics and Space Administration — This effort will research and implement advanced Multiple-Input Multiple-Output (MIMO) Synthetic Aperture Radar (SAR) techniques which have the potential to improve...

  3. Outsourcing, public Input provision and policy cooperation

    OpenAIRE

    Aronsson, Thomas; Koskela, Erkki

    2009-01-01

    This paper concerns public input provision as an instrument for redistribution under international outsourcing by using a model-economy comprising two countries, North and South, where firms in the North may outsource part of their low-skilled labor intensive production to the South. We consider two interrelated issues: (i) the incentives for each country to modify the provision of public input goods in response to international outsourcing, and (ii) whether international outsourcing justifie...

  4. Pressure ulcers: Current understanding and newer modalities of treatment

    Directory of Open Access Journals (Sweden)

    Surajit Bhattacharya

    2015-01-01

    Full Text Available This article reviews the mechanism, symptoms, causes, severity, diagnosis, prevention and present recommendations for surgical as well as non-surgical management of pressure ulcers. Particular focus has been placed on the current understandings and the newer modalities for the treatment of pressure ulcers. The paper also covers the role of nutrition and pressure-release devices such as cushions and mattresses as a part of the treatment algorithm for preventing and quick healing process of these wounds. Pressure ulcers develop primarily from pressure and shear; are progressive in nature and most frequently found in bedridden, chair bound or immobile people. They often develop in people who have been hospitalised for a long time generally for a different problem and increase the overall time as well as cost of hospitalisation that have detrimental effects on patient′s quality of life. Loss of sensation compounds the problem manifold, and failure of reactive hyperaemia cycle of the pressure prone area remains the most important aetiopathology. Pressure ulcers are largely preventable in nature, and their management depends on their severity. The available literature about severity of pressure ulcers, their classification and medical care protocols have been described in this paper. The present treatment options include various approaches of cleaning the wound, debridement, optimised dressings, role of antibiotics and reconstructive surgery. The newer treatment options such as negative pressure wound therapy, hyperbaric oxygen therapy, cell therapy have been discussed, and the advantages and disadvantages of current and newer methods have also been described.

  5. Pressure ulcers: Current understanding and newer modalities of treatment

    Science.gov (United States)

    Bhattacharya, Surajit; Mishra, R. K.

    2015-01-01

    This article reviews the mechanism, symptoms, causes, severity, diagnosis, prevention and present recommendations for surgical as well as non-surgical management of pressure ulcers. Particular focus has been placed on the current understandings and the newer modalities for the treatment of pressure ulcers. The paper also covers the role of nutrition and pressure-release devices such as cushions and mattresses as a part of the treatment algorithm for preventing and quick healing process of these wounds. Pressure ulcers develop primarily from pressure and shear; are progressive in nature and most frequently found in bedridden, chair bound or immobile people. They often develop in people who have been hospitalised for a long time generally for a different problem and increase the overall time as well as cost of hospitalisation that have detrimental effects on patient's quality of life. Loss of sensation compounds the problem manifold, and failure of reactive hyperaemia cycle of the pressure prone area remains the most important aetiopathology. Pressure ulcers are largely preventable in nature, and their management depends on their severity. The available literature about severity of pressure ulcers, their classification and medical care protocols have been described in this paper. The present treatment options include various approaches of cleaning the wound, debridement, optimised dressings, role of antibiotics and reconstructive surgery. The newer treatment options such as negative pressure wound therapy, hyperbaric oxygen therapy, cell therapy have been discussed, and the advantages and disadvantages of current and newer methods have also been described. PMID:25991879

  6. Generic MIDI devices as new input for specialized software

    Directory of Open Access Journals (Sweden)

    Marcin Badurowicz

    2016-12-01

    Full Text Available There are plenty of sublime devices, including input devices, for all kinds of specialists working with computers available on the market. Furthermore, the more specific solutions are needed, the more expensive and complicated they are. At the time when many people prefer to try as many things as possible before selecting the specific learning paths, both high price and high entry threshold, can appear as blockers. In the paper, there are selected some hardware and software solutions for facilitating the work of the professionals , who expect more analog-like interfaces and more natural ways to control computers presented. Additionally, the authors describe original software and hardware solution that allows the use of wide range MIDI devices as custom input devices. The concept of the software made is being presented, as well as some results of initial interaction of different kind of professionals and the proposed solution software and hardware.

  7. Model reduction of nonlinear systems subject to input disturbances

    KAUST Repository

    Ndoye, Ibrahima

    2017-07-10

    The method of convex optimization is used as a tool for model reduction of a class of nonlinear systems in the presence of disturbances. It is shown that under some conditions the nonlinear disturbed system can be approximated by a reduced order nonlinear system with similar disturbance-output properties to the original plant. The proposed model reduction strategy preserves the nonlinearity and the input disturbance nature of the model. It guarantees a sufficiently small error between the outputs of the original and the reduced-order systems, and also maintains the properties of input-to-state stability. The matrices of the reduced order system are given in terms of a set of linear matrix inequalities (LMIs). The paper concludes with a demonstration of the proposed approach on model reduction of a nonlinear electronic circuit with additive disturbances.

  8. Treatment modalities for patients with gambling disorder.

    Science.gov (United States)

    Choi, Sam-Wook; Shin, Young-Chul; Kim, Dai-Jin; Choi, Jung-Seok; Kim, Seohee; Kim, Seung-Hyun; Youn, HyunChul

    2017-01-01

    Gambling disorder (GD) is defined as persistent and recurrent problematic gambling behavior leading to clinically significant impairment or distress. The prevalence of GD has been shown to be 1.2-7.1% in the general population. GD can severely impact on personal and vocational wellbeing as well as lead to financial problems, and has been known to be difficult to treat. This review describes the available pharmacotherapy/psychosocial treatments for GD patients, and summarizes data on the effectiveness of these GD treatments. This review refers to newly as well as previously published studies and guidelines. The description of pharmacotherapy mainly focuses on opioid receptor antagonists, selective serotonin reuptake inhibitors, and mood stabilizers. Psychosocial treatments/strategies mainly include cognitive behavioral therapy, motivational interviewing, and Gamblers Anonymous. We also introduce relatively novel treatment modalities. This review can help clinicians to decide treatment plans for their GD patients. In addition, it can be used as a reference for designing future research.

  9. [Physical treatment modalities for chronic leg ulcers].

    Science.gov (United States)

    Dissemond, J

    2010-05-01

    An increasing numbers of physical treatment options are available for chronic leg ulcer. In this review article, compression therapy, therapeutic ultrasound, negative pressure therapy, extracorporeal shock wave therapy, electrostimulation therapy, electromagnetic therapy, photodynamic therapy, water-filtered infrared-A-radiation and hydrotherapy are discussed in terms of their practical applications and the underlying evidence. With the exception of compression therapy for most of these treatments, good scientific data are not available. However this is a widespread problem in the treatment of chronic wounds. Nevertheless, several of the described methods such as negative pressure therapy represent one of the gold standards in practical treatment of patients with chronic leg ulcers. Although the use of physical treatment modalities may improve healing in patients with chronic leg ulcers, the diagnosis and treatment of the underlying causes are essential for long-lasting success.

  10. MR microscopy as a research modality

    International Nuclear Information System (INIS)

    Kang, Heung Sik; Kim, Seung Hyup; Han, Man Chung; Lee, Sang Hoon; Lee, Yoon Seong; Yi, Jung Han; Cho, Zang Hee

    1988-01-01

    A combination of high gradient (0.46mT/cm) and small radiofrequency coils (8cm diameter) was used to obtain images with effective thickness of 2.0mm and pixel dimensions as small as 196 μ in the live chick embryo and surgically resected human femoral head with avascular necrosis. The signal-to-noise ratio was sufficient to allow identification of major anatomical structures of live chick embryo and delineation of osteonecrotic segment in femoral head. The changes of signal intensity in necrotic femoral head was well correlated with histopathologic findings. MR microscopy is considered as a good research modality in the field of embryology, teratology and MR tissue characterization

  11. Forms of Address as Discrete Modal Operators

    Directory of Open Access Journals (Sweden)

    Wojciech Paweł Sosnowski

    2016-12-01

    Full Text Available Forms of Address as Discrete Modal Operators The category of expressions of politeness includes, among others, forms of address. Forms of address express honorification. Honorification can be defined as a special type of meaning that consists of information about the social and interpersonal relations between the speaker and the addressee, the speaker and the hearer, and the speaker and the protagonist of the predication. As far as their place in the syntactic structure is concerned, forms of address can either be integrated with the other elements of a predication or not. However, they are always part of a predication’s semantic structure. Moreover, forms of address convey the speaker’s attitude to the meaning of the predicate that they want to convey, which consequently means that forms of address also carry a modal element. Modality can be defined as a situation in which an individual is in a particular mental state, i.e. exhibits some kind of attitude to a situation or a type of situations. Forms of address can be categorised as modal operators conveying imperatives, requests, suppositions, etc. The term "operator" can be used for a unit of language when it changes the semantic structure of the predication. My research on honorification is mainly based on contemporary corpora, both monolingual and multilingual. In the present study, I analyse forms of address which carry imperative and optative meanings.   Formy adresatywne jako dyskretne operatory modalne W obrębie wyrażeń realizujących funkcje grzecznościowe znajduje się grupa form adresatywnych. Są one częścią kategorii honoryfikatywności rozumianej jako szczególny rodzaj znaczenia zawartego w treści wypowiedzi, informację o towarzysko-społecznej relacji między nadawcą a odbiorcą, nadawcą a słuchaczem oraz nadawcą a bohaterem wypowiedzi. Gramatycznie formy adresatywne mogą być zarówno zintegrowane, jak i niezintegrowane syntaktycznie z resztą wypowiedzi, ale

  12. Exploring prayer as a spiritual modality.

    Science.gov (United States)

    Farah, Jennifer; McColl, Mary Ann

    2008-02-01

    What does it mean to focus on the spiritual in occupational therapy? What interventions would qualify as spiritual modalities? This paper attempts to define the boundaries of what may be considered legitimate uses of spirituality in occupational therapy by using the example of prayer. The purpose of this paper was to provide an in-depth analysis of the use of prayer in practice. Medical and allied health journals were searched using the terms spirituality, spirit, religion, and prayer. Identified articles were synthesized to identify potential advantages and disadvantages of using prayer in therapy. Prayer can be considered an appropriate occupational therapy intervention so long as four questions can be answered positively. To answer these questions, guidelines are provided that will lead the therapist through a decision making process to determine the appropriateness of incorporating prayer into any clinical situation.

  13. MR microscopy as a research modality

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Heung Sik; Kim, Seung Hyup; Han, Man Chung; Lee, Sang Hoon; Lee, Yoon Seong [College of Medicine, Seoul National University, Seoul (Korea, Republic of); Yi, Jung Han; Cho, Zang Hee [Korea Advanced insititute of Science, Taejon (Korea, Republic of)

    1988-02-15

    A combination of high gradient (0.46mT/cm) and small radiofrequency coils (8cm diameter) was used to obtain images with effective thickness of 2.0mm and pixel dimensions as small as 196 {mu} in the live chick embryo and surgically resected human femoral head with avascular necrosis. The signal-to-noise ratio was sufficient to allow identification of major anatomical structures of live chick embryo and delineation of osteonecrotic segment in femoral head. The changes of signal intensity in necrotic femoral head was well correlated with histopathologic findings. MR microscopy is considered as a good research modality in the field of embryology, teratology and MR tissue characterization.

  14. The elementary fusion modalities of osteoclasts

    DEFF Research Database (Denmark)

    Søe, Kent; Hobolt-Pedersen, Anne Sofie; Delaisse, Jean Marie

    2015-01-01

    , are not known for the osteoclast. Here we show that osteoclast fusion partners are characterized by differences in mobility, nuclearity, and differentiation level. Our demonstration was based on time-laps videos of human osteoclast preparations from three donors where 656 fusion events were analyzed. Fusions......The last step of the osteoclast differentiation process is cell fusion. Most efforts to understand the fusion mechanism have focused on the identification of molecules involved in the fusion process. Surprisingly, the basic fusion modalities, which are well known for fusion of other cell types...... between a mobile and an immobile partner were most frequent (62%), while fusion between two mobile (26%) or two immobile partners (12%) was less frequent (p fusion partner contained more nuclei than the mobile one (p

  15. STRUKTUR MODAL DAN MODAL KERJA PT XYZ SERTA PENGARUHNYA TERHADAP KINERJA PERUSAHAAN

    Directory of Open Access Journals (Sweden)

    Untung Setiono

    2017-01-01

    Full Text Available n 2012, the electronic payment system transactions reached IDR 104.830 trillion or increase 46,52% from the previous year.  PT. XYZ is the  pioneer in the electronic payment system Indonesia  and still one of the leading companies in electronic payment system interbank, through ATM (Automatic Teller Machine and EDC (Electronic Data Capture in Indonesia.  In 2012 the company spent USD 3,4 million on software tandem from a foreign vendor.  Therefore it is important to study (1 policy on the modal structure of the company, (2 the working capital policy of the company, (3 the monetary performance relationship of the company based on the 2 policies.  The method used to analyze the data is multiple linear regression analysis; this method is used to calculate the relationship between the structure variable of the capital and working capital.  The result is; 1 the structure policy on the capital of the company is in accordance with the Pecking Order theory where the company uses their own capital before applying the long term debt to the others, 2 the inefficient policy on the company’s working capital is because most of the active asset is in monthly deposit bonds and even extended  the active debt, 3 the relationship between short term debt and liquidity ratio is negative while the total debt (short and long term has a positive correlation with the solvability/leverage ratio of the company.  The research recommends the management to decrease the active asset and uses it for long term investment not only for timed deposit.Keywords:  ATM, EDC, capital structure, financial performance     AbstrakVoulme transaksi dalam menggunakan sistem pembayaran elektronis pada tahun 2012 mencapai Rp104.830 triliun atau meningkat sekitar 46,52% dari tahun sebelumnya. PT XYZ adalah salah satu perusahaan pionir dalam sistem bidang pembayaran elektronis di Indonesia dan tetap menjadi pemain utama dalam sistem pembayaran elektronis antar bank, ATM

  16. The effect of response modality on immediate serial recall in dementia of the Alzheimer type.

    Science.gov (United States)

    Macé, Anne-Laure; Ergis, Anne-Marie; Caza, Nicole

    2012-09-01

    Contrary to traditional models of verbal short-term memory (STM), psycholinguistic accounts assume that temporary retention of verbal materials is an intrinsic property of word processing. Therefore, memory performance will depend on the nature of the STM tasks, which vary according to the linguistic representations they engage. The aim of this study was to explore the effect of response modality on verbal STM performance in individuals with dementia of the Alzheimer Type (DAT), and its relationship with the patients' word-processing deficits. Twenty individuals with mild DAT and 20 controls were tested on an immediate serial recall (ISR) task using the same items across two response modalities (oral and picture pointing) and completed a detailed language assessment. When scoring of ISR performance was based on item memory regardless of item order, a response modality effect was found for all participants, indicating that they recalled more items with picture pointing than with oral response. However, this effect was less marked in patients than in controls, resulting in an interaction. Interestingly, when recall of both item and order was considered, results indicated similar performance between response modalities in controls, whereas performance was worse for pointing than for oral response in patients. Picture-naming performance was also reduced in patients relative to controls. However, in the word-to-picture matching task, a similar pattern of responses was found between groups for incorrectly named pictures of the same items. The finding of a response modality effect in item memory for all participants is compatible with the assumption that semantic influences are greater in picture pointing than in oral response, as predicted by psycholinguistic models. Furthermore, patients' performance was modulated by their word-processing deficits, showing a reduced advantage relative to controls. Overall, the response modality effect observed in this study for item

  17. Accelerometer-based estimation and modal velocity feedback vibration control of a stress-ribbon bridge with pneumatic muscles

    Science.gov (United States)

    Liu, Xiaohan; Schauer, Thomas; Goldack, Arndt; Bleicher, Achim; Schlaich, Mike

    2016-09-01

    Lightweight footbridges are very elegant but also prone to vibration. By employing active vibration control, smart footbridges could accomplish not only the architectural concept but also the required serviceability and comfort. Inertial sensors such as accelerometers allow the estimation of nodal velocities and displacements. A Kalman filter together with a band-limited multiple Fourier linear combiner (BMFLC) is applied to enable a drift-free estimation of these signals for the quasi-periodic motion under pedestrian excitation without extra information from other kinds of auxiliary sensors. The modal velocities of the structure are determined by using a second Kalman filter with the known applied actuator forces as inputs and the estimated nodal displacement and velocities as measurements. The obtained multi-modal velocities are then used for feedback control. An ultra-lightweight stress-ribbon footbridge built in the Peter-Behrens- Halle at the Technische Universitat Berlin served as the research object. Using two inertial sensors in optimal points we can estimate the dominant modal characteristics of this bridge. Real-time implementation and evaluation results of the proposed estimator will be presented in comparison to signals derived from classical displacement encoders. The real-time estimated modal velocities were applied in a multi-modal velocity feedback vibration control scheme with lightweight pneumatic muscle actuators. Experimental results demonstrate the feasibility of using inertial sensors for active vibration control of lightweight footbridges.

  18. Accelerometer-based estimation and modal velocity feedback vibration control of a stress-ribbon bridge with pneumatic muscles

    International Nuclear Information System (INIS)

    Liu, Xiaohan; Goldack, Arndt; Schlaich, Mike; Schauer, Thomas; Bleicher, Achim

    2016-01-01

    Lightweight footbridges are very elegant but also prone to vibration. By employing active vibration control, smart footbridges could accomplish not only the architectural concept but also the required serviceability and comfort. Inertial sensors such as accelerometers allow the estimation of nodal velocities and displacements. A Kalman filter together with a band-limited multiple Fourier linear combiner (BMFLC) is applied to enable a drift-free estimation of these signals for the quasi-periodic motion under pedestrian excitation without extra information from other kinds of auxiliary sensors. The modal velocities of the structure are determined by using a second Kalman filter with the known applied actuator forces as inputs and the estimated nodal displacement and velocities as measurements. The obtained multi-modal velocities are then used for feedback control. An ultra-lightweight stress-ribbon footbridge built in the Peter-Behrens- Halle at the Technische Universitat Berlin served as the research object. Using two inertial sensors in optimal points we can estimate the dominant modal characteristics of this bridge. Real-time implementation and evaluation results of the proposed estimator will be presented in comparison to signals derived from classical displacement encoders. The real-time estimated modal velocities were applied in a multi-modal velocity feedback vibration control scheme with lightweight pneumatic muscle actuators. Experimental results demonstrate the feasibility of using inertial sensors for active vibration control of lightweight footbridges. (paper)

  19. Modality-specific processing precedes amodal linguistic processing during L2 sign language acquisition: A longitudinal study.

    Science.gov (United States)

    Williams, Joshua T; Darcy, Isabelle; Newman, Sharlene D

    2016-02-01

    The present study tracked activation pattern differences in response to sign language processing by late hearing second language learners of American Sign Language. Learners were scanned before the start of their language courses. They were scanned again after their first semester of instruction and their second, for a total of 10 months of instruction. The study aimed to characterize modality-specific to modality-general processing throughout the acquisition of sign language. Results indicated that before the acquisition of sign language, neural substrates related to modality-specific processing were present. After approximately 45 h of instruction, the learners transitioned into processing signs on a phonological basis (e.g., supramarginal gyrus, putamen). After one more semester of input, learners transitioned once more to a lexico-semantic processing stage (e.g., left inferior frontal gyrus) at which language control mechanisms (e.g., left caudate, cingulate gyrus) were activated. During these transitional steps right hemispheric recruitment was observed, with increasing left-lateralization, which is similar to other native signers and L2 learners of spoken language; however, specialization for sign language processing with activation in the inferior parietal lobule (i.e., angular gyrus), even for late learners, was observed. As such, the present study is the first to track L2 acquisition of sign language learners in order to characterize modality-independent and modality-specific mechanisms for bilingual language processing. Copyright © 2015 Elsevier Ltd. All rights reserved.

  20. Aeroelastic modal dynamics of wind turbines including anisotropic effects

    DEFF Research Database (Denmark)

    Skjoldan, Peter Fisker

    frequency is thus identified as the dominant frequency in the response of a pure excitation of the mode observed in the inertial frame. A modal analysis tool based directly on the complex aeroelastic wind turbine code BHawC is presented. It uses the Coleman approach in isotropic conditions......Several methods for aeroelastic modal analysis of a rotating wind turbine are developed and used to analyse the modal dynamics of two simplified models and a complex model in isotropic and anisotropic conditions. The Coleman transformation is used to enable extraction of the modal frequencies...... of Floquet analysis or Hill's method which do not provide a unique reference frame for observing the modal frequency, to which any multiple of the rotor speed can be added. This indeterminacy is resolved by requiring that the periodic mode shape be as constant as possible in the inertial frame. The modal...

  1. Effects of auditory and visual modalities in recall of words.

    Science.gov (United States)

    Gadzella, B M; Whitehead, D A

    1975-02-01

    Ten experimental conditions were used to study the effects of auditory and visual (printed words, uncolored and colored pictures) modalities and their various combinations with college students. A recall paradigm was employed in which subjects responded in a written test. Analysis of data showed the auditory modality was superior to visual (pictures) ones but was not significantly different from visual (printed words) modality. In visual modalities, printed words were superior to colored pictures. Generally, conditions with multiple modes of representation of stimuli were significantly higher than for conditions with single modes. Multiple modalities, consisting of two or three modes, did not differ significantly from each other. It was concluded that any two modalities of the stimuli presented simultaneously were just as effective as three in recall of stimulus words.

  2. Integrating Conceptual Knowledge Within and Across Representational Modalities

    OpenAIRE

    McNorgan, Chris; Reid, Jackie; McRae, Ken

    2010-01-01

    Research suggests that concepts are distributed across brain regions specialized for processing information from different sensorimotor modalities. Multimodal semantic models fall into one of two broad classes differentiated by the assumed hierarchy of convergence zones over which information is integrated. In shallow models, communication within- and between-modality is accomplished using either direct connectivity, or a central semantic hub. In deep models, modalities are connected via casc...

  3. First-order modal logic theorem proving and standard PROLOG

    OpenAIRE

    Nonnengart, A.

    1992-01-01

    Many attempts have been started to combine logic programming and modal logics. Most of them however, do not use classical PROLOG, but extend the PROLOG idea in order to cope with modal logic formulae directly. These approaches have the disadvantage that for each logic new logic programming systems are to be developed and the knowledge and experience gathered from PROLOG can hardly be utilized. Modal logics based on Kripke-style relational semantics, however, allow a direct translation from mo...

  4. Modalization in the Political Column of Tempo Magazine

    OpenAIRE

    Rahmah, Maria Betti Sinaga and

    2017-01-01

    The study focuses on analyzing the use of modalization in the Political Column of Tempo Magazine. The objectives were to find out the type of modalization and to describe the use of modalization in the Political Column of Tempo magazine. The data were taken from Political Column of Tempo magazine published in June and July 2017. The source of data was Political Column in Tempo magazine. The data analysis applied descriptive qualitative research. There were 135 clauses which contained Modaliza...

  5. Multi-modal RGB–Depth–Thermal Human Body Segmentation

    DEFF Research Database (Denmark)

    Palmero, Cristina; Clapés, Albert; Bahnsen, Chris

    2016-01-01

    This work addresses the problem of human body segmentation from multi-modal visual cues as a first stage of automatic human behavior analysis. We propose a novel RGB-Depth-Thermal dataset along with a multi-modal seg- mentation baseline. The several modalities are registered us- ing a calibration...... to other state-of-the-art meth- ods, obtaining an overlap above 75% on the novel dataset when compared to the manually annotated ground-truth of human segmentations....

  6. Modal nudging in nonlinear elasticity: Tailoring the elastic post-buckling behaviour of engineering structures

    Science.gov (United States)

    Cox, B. S.; Groh, R. M. J.; Avitabile, D.; Pirrera, A.

    2018-07-01

    The buckling and post-buckling behaviour of slender structures is increasingly being harnessed for smart functionalities. Equally, the post-buckling regime of many traditional engineering structures is not being used for design and may therefore harbour latent load-bearing capacity for further structural efficiency. Both applications can benefit from a robust means of modifying and controlling the post-buckling behaviour for a specific purpose. To this end, we introduce a structural design paradigm termed modal nudging, which can be used to tailor the post-buckling response of slender engineering structures without any significant increase in mass. Modal nudging uses deformation modes of stable post-buckled equilibria to perturb the undeformed baseline geometry of the structure imperceptibly, thereby favouring the seeded post-buckling response over potential alternatives. The benefits of this technique are enhanced control over the post-buckling behaviour, such as modal differentiation for smart structures that use snap-buckling for shape adaptation, or alternatively, increased load-carrying capacity, increased compliance or a shift from imperfection sensitivity to imperfection insensitivity. Although these concepts are, in theory, of general applicability, we concentrate here on planar frame structures analysed using the nonlinear finite element method and numerical continuation procedures. Using these computational techniques, we show that planar frame structures may exhibit isolated regions of stable equilibria in otherwise unstable post-buckling regimes, or indeed stable equilibria entirely disconnected from the natural structural response. In both cases, the load-carrying capacity of these isolated stable equilibria is greater than the natural structural response of the frames. Using the concept of modal nudging it is possible to "nudge" the frames onto these equilibrium paths of greater load-carrying capacity. Due to the scale invariance of modal nudging

  7. Residual Shuffling Convolutional Neural Networks for Deep Semantic Image Segmentation Using Multi-Modal Data

    Science.gov (United States)

    Chen, K.; Weinmann, M.; Gao, X.; Yan, M.; Hinz, S.; Jutzi, B.; Weinmann, M.

    2018-05-01

    In this paper, we address the deep semantic segmentation of aerial imagery based on multi-modal data. Given multi-modal data composed of true orthophotos and the corresponding Digital Surface Models (DSMs), we extract a variety of hand-crafted radiometric and geometric features which are provided separately and in different combinations as input to a modern deep learning framework. The latter is represented by a Residual Shuffling Convolutional Neural Network (RSCNN) combining the characteristics of a Residual Network with the advantages of atrous convolution and a shuffling operator to achieve a dense semantic labeling. Via performance evaluation on a benchmark dataset, we analyze the value of different feature sets for the semantic segmentation task. The derived results reveal that the use of radiometric features yields better classification results than the use of geometric features for the considered dataset. Furthermore, the consideration of data on both modalities leads to an improvement of the classification results. However, the derived results also indicate that the use of all defined features is less favorable than the use of selected features. Consequently, data representations derived via feature extraction and feature selection techniques still provide a gain if used as the basis for deep semantic segmentation.

  8. Evaluation of modal properties of cabinet type instrument of nuclear power plant

    International Nuclear Information System (INIS)

    Cho, Y. H.; Park, H. K.; Cho, S. K.

    1999-01-01

    The seismic qualification of safety-related equipment is usually achieved through analysis and testing. Analysis method is preferably adopted for structurally simple equipments which are easy to be mathematically modeled. However, even for relatively complex equipments, analysis method is occasionlly used for computing the input motion or supporting information for the component test followed. Electrical cabinet is a typical example for which analysis method is combinedly used with test to get modal properties of the enclosing cabinet structure. In this paper, with respect to a typical cabinet-type structure(instrumentation cabinet of nuclear power plant) a comparative study has been performed between three different state-of-the-art modeling techniques: lumped mass model, frame model, and FEM modal. From the study results, it has been found that the modal properties of the cabinet-type structure in the elastic behavior range can be reasonably computed through any type of modeling techniques in the practice with slight modification of model properties to get better accuracy. However, it needs additional modeling techniques to get reasonable results up to nonlinear range

  9. Nuclear waste shipping container response to severe accident conditions, A brief critique of the modal study

    International Nuclear Information System (INIS)

    Audin, L.

    1990-12-01

    The Modal Study (NUREG/CR-4829) attempts to upgrade the analysis of spent nuclear fuel transportation accidents, and to verify the validity of the present regulatory scheme of cask performance standards as a means to minimize risk. While an improvement over many prior efforts in this area (such as NUREG-0170), it unfortunately fails to create a realistic simulation either of a shipping cask, the severe conditions to which it could be subjected, or the potential damage to the spent fuel cargo during an accident. There are too many deficiencies in its analysis to allow acceptance of its results for the presumed cask design, and many pending changes in new containers, cargoes and shipping patterns will limit applicability of the Modal Study to future shipments. In essence, the Modal Study is a good start, but is too simplistic, incomplete, outdated and open to serious question to be used as the basis for any present-day environmental or risk assessment of spent fuel transportation. It needs to be redone, with peer review during its production and experimental verification of its assumptions, before it has any relevance to the shipments planned to Yucca Mountain. Finally, it must be expanded into a full risk assessment by inputing its radiological release fractions and probabilities into a valid dispersal simulation to properly determine the impact of its results. 51 refs

  10. Feeling music: integration of auditory and tactile inputs in musical meter perception.

    Science.gov (United States)

    Huang, Juan; Gamble, Darik; Sarnlertsophon, Kristine; Wang, Xiaoqin; Hsiao, Steven

    2012-01-01

    Musicians often say that they not only hear, but also "feel" music. To explore the contribution of tactile information in "feeling" musical rhythm, we investigated the degree that auditory and tactile inputs are integrated in humans performing a musical meter recognition task. Subjects discriminated between two types of sequences, 'duple' (march-like rhythms) and 'triple' (waltz-like rhythms) presented in three conditions: 1) Unimodal inputs (auditory or tactile alone), 2) Various combinations of bimodal inputs, where sequences were distributed between the auditory and tactile channels such that a single channel did not produce coherent meter percepts, and 3) Simultaneously presented bimodal inputs where the two channels contained congruent or incongruent meter cues. We first show that meter is perceived similarly well (70%-85%) when tactile or auditory cues are presented alone. We next show in the bimodal experiments that auditory and tactile cues are integrated to produce coherent meter percepts. Performance is high (70%-90%) when all of the metrically important notes are assigned to one channel and is reduced to 60% when half of these notes are assigned to one channel. When the important notes are presented simultaneously to both channels, congruent cues enhance meter recognition (90%). Performance drops dramatically when subjects were presented with incongruent auditory cues (10%), as opposed to incongruent tactile cues (60%), demonstrating that auditory input dominates meter perception. We believe that these results are the first demonstration of cross-modal sensory grouping between any two senses.

  11. Converging modalities ground abstract categories: the case of politics.

    Directory of Open Access Journals (Sweden)

    Ana Rita Farias

    Full Text Available Three studies are reported examining the grounding of abstract concepts across two modalities (visual and auditory and their symbolic representation. A comparison of the outcomes across these studies reveals that the symbolic representation of political concepts and their visual and auditory modalities is convergent. In other words, the spatial relationships between specific instances of the political categories are highly overlapping across the symbolic, visual and auditory modalities. These findings suggest that abstract categories display redundancy across modal and amodal representations, and are multimodal.

  12. Multimodal Image Alignment via Linear Mapping between Feature Modalities.

    Science.gov (United States)

    Jiang, Yanyun; Zheng, Yuanjie; Hou, Sujuan; Chang, Yuchou; Gee, James

    2017-01-01

    We propose a novel landmark matching based method for aligning multimodal images, which is accomplished uniquely by resolving a linear mapping between different feature modalities. This linear mapping results in a new measurement on similarity of images captured from different modalities. In addition, our method simultaneously solves this linear mapping and the landmark correspondences by minimizing a convex quadratic function. Our method can estimate complex image relationship between different modalities and nonlinear nonrigid spatial transformations even in the presence of heavy noise, as shown in our experiments carried out by using a variety of image modalities.

  13. On the Force Drop Off Phenomenon in Shaker Testing in Experimental Modal Analysis

    Directory of Open Access Journals (Sweden)

    Paulo Sergio Varoto

    2002-01-01

    Full Text Available The Electrodynamic Vibration Exciter (shakers has been one of the most employed excitation sources in modal tests. The shaker is an electromechanical device that provides a mechanical motion due to the input signal sent to its coil. Despite being widely used, it is well known that the shaker interacts with the structure under test. In particular, when the structure passes through a given resonance, the force delivered by the shaker abruptly decreases, causing the so called drop off phenomenon. This paper aims to study this force drop off phenomenon in the single shaker modal testing. Analytical models are developed to help in understanding the physical principles involved in the interaction between the shaker and the structure under test. Experimental analyses are performed using different shakers as well as excitation signals, in order to evaluate the effects of the input signal, as well as the power amplifier operational modes, on the structure dynamics. Preliminary tests revealed that significant distortions might occur during vibration tests using shakers and these distortions significantly affect the determination of the structure response.

  14. Modal analysis of main steam line piping under high energy line break condition

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Tae-Jin; Kim, Seung Hyun; Je, Sang-Yun; Chang, Yoon-Suk [Kyung Hee University, Yongin (Korea, Republic of)

    2016-10-15

    If HELB (High Energy Line Break) occurs in NPPs (Nuclear Power Plants), not only environmental effect like release of radioactive material but also secondary structural defects should be considered. Jet impingement phenomenon caused by sudden pipe rupture may lead to severe damage on neighboring safe-related components and other structure. Lots of studies have been conducted to assess dynamic behaviors of the SG and MSL piping while pipe whip restraints and jet impingement shields are taken into account during design stage. Arroyo et al. performed modal analyses of a simple square component to examine the jet impingement phenomenon. Also, structural characteristics were predicted to assure structural integrity against the HELB. In this study, we examined dynamic characteristics of SG and MSL piping in a typical 1000MWe NPP. Simulation was performed by using two commercial computational softwares. In particular, modal analyses were conducted to determine mode shapes and natural frequencies of the structure and maximum displacements. The data obtain from each software were compared and observation was discussed in relation to the jet impingement phenomenon. In this research, modal analyses on the SG and MSL piping were carried out to get natural frequencies, vibration mode shapes and maximum displacements. Thereby, the following key finding was observed. (1) Maximum displacement was calculated at the top of SG outlet nozzle with y-directional bending at the third mode. (2) The differences between two models were respectively 7% in natural frequencies and less than 1% in maximum displacements.

  15. Six axis force feedback input device

    Science.gov (United States)

    Ohm, Timothy (Inventor)

    1998-01-01

    The present invention is a low friction, low inertia, six-axis force feedback input device comprising an arm with double-jointed, tendon-driven revolute joints, a decoupled tendon-driven wrist, and a base with encoders and motors. The input device functions as a master robot manipulator of a microsurgical teleoperated robot system including a slave robot manipulator coupled to an amplifier chassis, which is coupled to a control chassis, which is coupled to a workstation with a graphical user interface. The amplifier chassis is coupled to the motors of the master robot manipulator and the control chassis is coupled to the encoders of the master robot manipulator. A force feedback can be applied to the input device and can be generated from the slave robot to enable a user to operate the slave robot via the input device without physically viewing the slave robot. Also, the force feedback can be generated from the workstation to represent fictitious forces to constrain the input device's control of the slave robot to be within imaginary predetermined boundaries.

  16. Characterization of industrial process waste heat and input heat streams

    Energy Technology Data Exchange (ETDEWEB)

    Wilfert, G.L.; Huber, H.B.; Dodge, R.E.; Garrett-Price, B.A.; Fassbender, L.L.; Griffin, E.A.; Brown, D.R.; Moore, N.L.

    1984-05-01

    The nature and extent of industrial waste heat associated with the manufacturing sector of the US economy are identified. Industry energy information is reviewed and the energy content in waste heat streams emanating from 108 energy-intensive industrial processes is estimated. Generic types of process equipment are identified and the energy content in gaseous, liquid, and steam waste streams emanating from this equipment is evaluated. Matchups between the energy content of waste heat streams and candidate uses are identified. The resultant matrix identifies 256 source/sink (waste heat/candidate input heat) temperature combinations. (MHR)

  17. Computer Generated Inputs for NMIS Processor Verification

    International Nuclear Information System (INIS)

    J. A. Mullens; J. E. Breeding; J. A. McEvers; R. W. Wysor; L. G. Chiang; J. R. Lenarduzzi; J. T. Mihalczo; J. K. Mattingly

    2001-01-01

    Proper operation of the Nuclear Identification Materials System (NMIS) processor can be verified using computer-generated inputs [BIST (Built-In-Self-Test)] at the digital inputs. Preselected sequences of input pulses to all channels with known correlation functions are compared to the output of the processor. These types of verifications have been utilized in NMIS type correlation processors at the Oak Ridge National Laboratory since 1984. The use of this test confirmed a malfunction in a NMIS processor at the All-Russian Scientific Research Institute of Experimental Physics (VNIIEF) in 1998. The NMIS processor boards were returned to the U.S. for repair and subsequently used in NMIS passive and active measurements with Pu at VNIIEF in 1999

  18. Harmonize input selection for sediment transport prediction

    Science.gov (United States)

    Afan, Haitham Abdulmohsin; Keshtegar, Behrooz; Mohtar, Wan Hanna Melini Wan; El-Shafie, Ahmed

    2017-09-01

    In this paper, three modeling approaches using a Neural Network (NN), Response Surface Method (RSM) and response surface method basis Global Harmony Search (GHS) are applied to predict the daily time series suspended sediment load. Generally, the input variables for forecasting the suspended sediment load are manually selected based on the maximum correlations of input variables in the modeling approaches based on NN and RSM. The RSM is improved to select the input variables by using the errors terms of training data based on the GHS, namely as response surface method and global harmony search (RSM-GHS) modeling method. The second-order polynomial function with cross terms is applied to calibrate the time series suspended sediment load with three, four and five input variables in the proposed RSM-GHS. The linear, square and cross corrections of twenty input variables of antecedent values of suspended sediment load and water discharge are investigated to achieve the best predictions of the RSM based on the GHS method. The performances of the NN, RSM and proposed RSM-GHS including both accuracy and simplicity are compared through several comparative predicted and error statistics. The results illustrated that the proposed RSM-GHS is as uncomplicated as the RSM but performed better, where fewer errors and better correlation was observed (R = 0.95, MAE = 18.09 (ton/day), RMSE = 25.16 (ton/day)) compared to the ANN (R = 0.91, MAE = 20.17 (ton/day), RMSE = 33.09 (ton/day)) and RSM (R = 0.91, MAE = 20.06 (ton/day), RMSE = 31.92 (ton/day)) for all types of input variables.

  19. Shaped input distributions for structural damage localization

    DEFF Research Database (Denmark)

    Ulriksen, Martin Dalgaard; Bernal, Dionisio; Damkilde, Lars

    2018-01-01

    localization method is cast that operates on the premise of shaping inputs—whose spatial distribution is fixed—by use of a model, such that these inputs, in one structural subdomain at a time, suppress certain steady-state vibration quantities (depending on the type of damage one seeks to interrogate for......). Accordingly, damage is localized when the vibration signature induced by the shaped inputs in the damaged state corresponds to that in the reference state, hereby implying that the approach does not point directly to damage. Instead, it operates with interrogation based on postulated damage patterns...

  20. A parallel input composite transimpedance amplifier

    Science.gov (United States)

    Kim, D. J.; Kim, C.

    2018-01-01

    A new approach to high performance current to voltage preamplifier design is presented. The design using multiple operational amplifiers (op-amps) has a parasitic capacitance compensation network and a composite amplifier topology for fast, precision, and low noise performance. The input stage consisting of a parallel linked JFET op-amps and a high-speed bipolar junction transistor (BJT) gain stage driving the output in the composite amplifier topology, cooperating with the capacitance compensation feedback network, ensures wide bandwidth stability in the presence of input capacitance above 40 nF. The design is ideal for any two-probe measurement, including high impedance transport and scanning tunneling microscopy measurements.

  1. Nuclear reaction inputs based on effective interactions

    Energy Technology Data Exchange (ETDEWEB)

    Hilaire, S.; Peru, S.; Dubray, N.; Dupuis, M.; Bauge, E. [CEA, DAM, DIF, Arpajon (France); Goriely, S. [Universite Libre de Bruxelles, Institut d' Astronomie et d' Astrophysique, CP-226, Brussels (Belgium)

    2016-11-15

    Extensive nuclear structure studies have been performed for decades using effective interactions as sole input. They have shown a remarkable ability to describe rather accurately many types of nuclear properties. In the early 2000 s, a major effort has been engaged to produce nuclear reaction input data out of the Gogny interaction, in order to challenge its quality also with respect to nuclear reaction observables. The status of this project, well advanced today thanks to the use of modern computers as well as modern nuclear reaction codes, is reviewed and future developments are discussed. (orig.)

  2. Simulation of a Multidimensional Input Quantum Perceptron

    Science.gov (United States)

    Yamamoto, Alexandre Y.; Sundqvist, Kyle M.; Li, Peng; Harris, H. Rusty

    2018-06-01

    In this work, we demonstrate the improved data separation capabilities of the Multidimensional Input Quantum Perceptron (MDIQP), a fundamental cell for the construction of more complex Quantum Artificial Neural Networks (QANNs). This is done by using input controlled alterations of ancillary qubits in combination with phase estimation and learning algorithms. The MDIQP is capable of processing quantum information and classifying multidimensional data that may not be linearly separable, extending the capabilities of the classical perceptron. With this powerful component, we get much closer to the achievement of a feedforward multilayer QANN, which would be able to represent and classify arbitrary sets of data (both quantum and classical).

  3. Hypoxic conditioning as a new therapeutic modality

    Directory of Open Access Journals (Sweden)

    Samuel eVerges

    2015-06-01

    Full Text Available Preconditioning refers to a procedure by which a single noxious stimulus below the threshold of damage is applied to the tissue in order to increase resistance to the same or even different noxious stimuli given above the threshold of damage. Hypoxic preconditioning relies on complex and active defenses that organisms have developed to counter the adverse consequences of oxygen deprivation. The protection it confers against ischemic attack for instance as well as the underlying biological mechanisms have been extensively investigated in animal models. Based on these data, hypoxic conditioning (consisting in recurrent exposure to hypoxia has been suggested a potential non-pharmacological therapeutic intervention to enhance some physiological functions in individuals in whom acute or chronic pathological events are anticipated or existing. In addition to healthy subjects, some benefits have been reported in patients with cardiovascular and pulmonary diseases as well as in overweight and obese individuals. Hypoxic conditioning consisting in sessions of intermittent exposure to moderate hypoxia repeated over several weeks may induce hematological, vascular, metabolic and neurological effects. This review addresses the existing evidence regarding the use of hypoxic conditioning as a potential therapeutic modality and emphasizes on many remaining issues to clarify and future researches to be performed in the field.

  4. A Comparison of Passion and Teaching Modality

    Directory of Open Access Journals (Sweden)

    Scott Greenberger

    2016-01-01

    Full Text Available Research exists that applies the dualistic model of passion to face-to-face teaching, but no research has applied this model to online instruction. Distance education theories imply a need to discover factors contributing to online faculty motivation to engage students. Although there has been extensive exploration of intrinsic and extrinsic motivation to teach online, factors contributing to consistent and optimal teaching behavior has received less attention. There is evidence that the passion construct is independent of both intrinsic and extrinsic motivation. A stratified random sample of online and face-to-face faculty (n = 92 were surveyed using the Passion Scale. The results showed that 95 percent of the sampled online faculty self-identified as passionate for their online instruction. In the between-groups analysis, there were no significant differences in the variables of passion orientation, harmonious passion, and obsessive passion by modality. This research provides a basis for future research of passion in online instruction. In addition, this study adds another dimension for research within distance education theory, providing increased evidence for what motivates online instructors to consistently and effectively engage students.

  5. Helioseismology in a bottle: modal acoustic velocimetry

    International Nuclear Information System (INIS)

    Triana, Santiago Andrés; Zimmerman, Daniel S; Lathrop, Daniel P; Nataf, Henri-Claude; Thorette, Aurélien; Lekic, Vedran

    2014-01-01

    Measurement of the differential rotation of the Sun's interior is one of the great achievements of helioseismology, providing important constraints for stellar physics. The technique relies on observing and analyzing rotationally-induced splittings of p-modes in the star. Here, we demonstrate the first use of the technique in a laboratory setting. We apply it in a spherical cavity with a spinning central core (spherical-Couette flow) to determine the mean azimuthal velocity of the air filling the cavity. We excite a number of acoustic resonances (analogous to p-modes in the Sun) using a speaker and record the response with an array of small microphones on the outer sphere. Many observed acoustic modes show rotationally-induced splittings, which allow us to perform an inversion to determine the air's azimuthal velocity as a function of both radius and latitude. We validate the method by comparing the velocity field obtained through inversion against the velocity profile measured with a calibrated hot film anemometer. This modal acoustic velocimetry technique has great potential for laboratory setups involving rotating fluids in axisymmetric cavities. It will be useful especially in liquid metals where direct optical methods are unsuitable and ultrasonic techniques very challenging at best. (paper)

  6. Imaging modalities of abdominal tumors in children

    International Nuclear Information System (INIS)

    Reither, M.

    1993-01-01

    Further technological progress in cross-sectional imaging modalities, accumuting experience with increasingly refined hardware and software and accumulating specific contrast media allow new algorithms for the assessment of abdominal tumors in children. However, ultrasound remains the diagnostic method of choice: Conventional roentgenology with or without contrast media is decreasing, but often reveals further differential diagnostic details. MRI is becoming more prominent and is often performed immediately after ultrasound. The inauguration of gradient echo sequences and consequent shorter examination times combined with the elimination of pulsation and motion artefacts extends the diagnostic spectrum of the upper and middle abdomen. The application of oral or rectal contrast agents for imaging of the GI tract ameliorates the differentiation of pathologic processes. Recently volumetric CT/ultrafast CT has been gaining in importance for abdominal examinations in the pediatric age group. CT especially is helpful if there are bony structures in the region being examined. CT, however, involves ionizing radiation and timely administration of oral and intravenous contrast material. Moreover, as pediatric radiologists, we must strongly withstand tendencies to perform CT more often because it is less expensive, rather than avoiding ionizing radiation by using MRI. (orig.) [de

  7. Taste of Fat: A Sixth Taste Modality?

    Science.gov (United States)

    Besnard, Philippe; Passilly-Degrace, Patricia; Khan, Naim A

    2016-01-01

    An attraction for palatable foods rich in lipids is shared by rodents and humans. Over the last decade, the mechanisms responsible for this specific eating behavior have been actively studied, and compelling evidence implicates a taste component in the orosensory detection of dietary lipids [i.e., long-chain fatty acids (LCFA)], in addition to textural, olfactory, and postingestive cues. The interactions between LCFA and specific receptors in taste bud cells (TBC) elicit physiological changes that affect both food intake and digestive functions. After a short overview of the gustatory pathway, this review brings together the key findings consistent with the existence of a sixth taste modality devoted to the perception of lipids. The main steps leading to this new paradigm (i.e., chemoreception of LCFA in TBC, cell signaling cascade, transfer of lipid signals throughout the gustatory nervous pathway, and their physiological consequences) will be critically analyzed. The limitations to this concept will also be discussed in the light of our current knowledge of the sense of taste. Finally, we will analyze the recent literature on obesity-related dysfunctions in the orosensory detection of lipids ("fatty" taste?), in relation to the overconsumption of fat-rich foods and the associated health risks. Copyright © 2016 the American Physiological Society.

  8. Therapeutic modalities for cow's milk allergy.

    Science.gov (United States)

    Seidman, Ernest G; Singer, Sanford

    2003-06-01

    To discuss current therapeutic modalities for cow's milk allergy and its prevention. The sources of data include original clinical studies carried out at Ste. Justine Hospital, as well as a systematic search of the published English and French language scientific literature restricted to human subjects using computerized searches (National Public Library of Medicine, Cochrane Database Systems Review) from 1997 to 2002. Search terms for article retrieval included food allergy, milk allergy, therapy, and prevention. The therapy of food allergies depends upon an accurate diagnosis, which remains a challenge in non--IgE-mediated cases. Dietary exclusion remains the mainstay of therapy, with medications reserved for exceptional patients. Preliminary evidence suggests that pancreatic enzyme supplementation may be of benefit for cases with multiple food allergies and severe eczema. Hydrolysate formula use is currently recommended for dietary allergy prevention in infants at an increased risk when maternal milk is insufficient or unavailable. The use of partially hydrolyzed formulas to prevent allergic disorders, including atopic dermatitis, is supported by clinical studies, but cannot be used in the already sensitized, milk-allergic child. Probiotics show enormous potential in preventing food allergic disorders as well.

  9. Spatial aspects of combined modality radiotherapy

    International Nuclear Information System (INIS)

    Bodey, Rachel K.; Evans, Phil M.; Flux, Glenn D.

    2005-01-01

    Background and purpose: A combined modality radiotherapy (CMRT) incorporates both external beam radiotherapy (EBT) and targeted radionuclide therapy (TRT) components. The spatial aspects of this combination were explored by utilising intensity modulated radiotherapy (IMRT) to provide a non-uniform EBT dose distribution. Patients and methods: Three methods of prescribing the required non-uniform distribution of EBT dose are described, based on both physical and biological criteria according to the distribution of TRT uptake. The results and consequences of these prescriptions are explored by application to three examples of patient data. Results: The planning procedure adopted allowed IMRT plans to be produced that met the prescription requirements. However, when the treatment was planned as a CMRT, compared with the use of EBT alone, more satisfactory target doses could be achieved with lower doses to normal tissues. The effects of errors in EBT delivery and in the functional data were found to cause a non-uniform prescription to tend towards the uniform case. Conclusions: The methods and results are relevant for more general biological treatment planning, in which IMRT may be used to produce dose distributions prescribed according to tumour function. The effects of delivery and dose calculation errors can have a significant impact on how such treatments should be planned

  10. On the Multi-Modal Object Tracking and Image Fusion Using Unsupervised Deep Learning Methodologies

    Science.gov (United States)

    LaHaye, N.; Ott, J.; Garay, M. J.; El-Askary, H. M.; Linstead, E.

    2017-12-01

    The number of different modalities of remote-sensors has been on the rise, resulting in large datasets with different complexity levels. Such complex datasets can provide valuable information separately, yet there is a bigger value in having a comprehensive view of them combined. As such, hidden information can be deduced through applying data mining techniques on the fused data. The curse of dimensionality of such fused data, due to the potentially vast dimension space, hinders our ability to have deep understanding of them. This is because each dataset requires a user to have instrument-specific and dataset-specific knowledge for optimum and meaningful usage. Once a user decides to use multiple datasets together, deeper understanding of translating and combining these datasets in a correct and effective manner is needed. Although there exists data centric techniques, generic automated methodologies that can potentially solve this problem completely don't exist. Here we are developing a system that aims to gain a detailed understanding of different data modalities. Such system will provide an analysis environment that gives the user useful feedback and can aid in research tasks. In our current work, we show the initial outputs our system implementation that leverages unsupervised deep learning techniques so not to burden the user with the task of labeling input data, while still allowing for a detailed machine understanding of the data. Our goal is to be able to track objects, like cloud systems or aerosols, across different image-like data-modalities. The proposed system is flexible, scalable and robust to understand complex likenesses within multi-modal data in a similar spatio-temporal range, and also to be able to co-register and fuse these images when needed.

  11. Imagining Nature during Music Listening

    DEFF Research Database (Denmark)

    Bonde, Lars Ole; Beck, Bolette Daniels

    2018-01-01

    Nature, its delights and horrors, its creatures, its challenges and affordances play an underrated role in receptive music therapy, especially Guided Imagery and Music (GIM). In general, people from Western cultures are challenged in their mostly recreational relationship with nature, while ancient...... and traditional cultures worship nature as a place of holiness and wholeness. In GIM, a client or a group listens to music in a relaxed state and multi-modal imagery is evoked and supported by the music. The imagery is shared with the guide/therapist. This chapter will focus on ‘nature imagery’ in GIM through...... a primarily qualitative, exploratory study....

  12. Modal behavior of a reduced scale pump-turbine impeller. Part 1: Experiments

    International Nuclear Information System (INIS)

    Escaler, X; Huetter, J K; Egusquiza, E; Farhat, M; Avellan, F

    2010-01-01

    An experimental investigation has been carried out to quantify the effects of surrounding fluid on the modal behavior of a reduced scale pump-turbine impeller. The modal properties of the fluid-structure system have been obtained by Experimental Modal Analysis (EMA) with the impeller suspended in air and inside a water reservoir. The impeller has been excited with an instrumented hammer and the response has been measured by means of miniature accelerometers. The Frequency Response Functions (FRF's) have been obtained from a large number of impacting positions in order to ensure the identification of the main mode shapes. As a result, the main modes of vibration have been well characterized both in air and in water in terms of natural frequency, damping ratio and mode shape. The first mode is the 2 Nodal Diameter (ND), the second one is the 0ND and the following ones are the 3ND coupled with the 1ND. The visual observation of the animated mode shapes and the level of the Modal Assurance Criterion (MAC) have permitted to correlate the homologous modes of vibration of the fluid-structure system in air and in water. From this comparison the added mass effect on the natural frequencies and the fluid effect on the damping ratios have been quantified for the most significant modes. With the surrounding water, the natural frequencies decrease in average by 10%. On the other hand, the damping ratios increase in average by 0.5%. In any case, the damping ratio appears to decrease with the frequency value of the mode.

  13. Free Modal Algebras Revisited: The Step-by-Step Method

    NARCIS (Netherlands)

    Bezhanishvili, N.; Ghilardi, Silvio; Jibladze, Mamuka

    2012-01-01

    We review the step-by-step method of constructing finitely generated free modal algebras. First we discuss the global step-by-step method, which works well for rank one modal logics. Next we refine the global step-by-step method to obtain the local step-by-step method, which is applicable beyond

  14. Polynomial modal analysis of lamellar diffraction gratings in conical mounting.

    Science.gov (United States)

    Randriamihaja, Manjakavola Honore; Granet, Gérard; Edee, Kofi; Raniriharinosy, Karyl

    2016-09-01

    An efficient numerical modal method for modeling a lamellar grating in conical mounting is presented. Within each region of the grating, the electromagnetic field is expanded onto Legendre polynomials, which allows us to enforce in an exact manner the boundary conditions that determine the eigensolutions. Our code is successfully validated by comparison with results obtained with the analytical modal method.

  15. The Logic and Semantics of Modal Propositions in Juan Caramuel

    Czech Academy of Sciences Publication Activity Database

    Dvořák, Petr

    19/43/, - (2005), s. 105-115. ISBN 80-7007-236-9. ISSN 0231-5955 Institutional research plan: CEZ:AV0Z90090514 Keywords : Juan Caramuel y Lobkowicz * modal logic * modalities * late scholasticism Subject RIV: AA - Philosophy ; Religion

  16. The effect of preference modality on self-control

    NARCIS (Netherlands)

    Klesse, Anne-Kathrin; Levav, J.; Goukens, C.

    2015-01-01

    The marketplace affords consumers various modalities to express their preferences (e.g., by pressing a button on a vending machine or making an oral request at a restaurant). In this paper, we compare speaking to manual preference expression modalities (button pressing, writing, and taking) and

  17. Screen Fingerprints as a Novel Modality for Active Authentication

    Science.gov (United States)

    2014-03-01

    Screen fingerprint is the new cyber biometric modality that we have proposed to measure and analyze active authentication. The screen finger ...as a new biometric modality for active authentication. Such a fingerprint is acquired by taking a screen recording of the computer being used and...extracting discriminative visual feature from the recording. 15. SUBJECT TERMS Active authentication, screen fingerprints, biometrics 16. SECURITY

  18. Creating Pretence and Sharing Friendship: Modal Expressions in Children's Play

    Science.gov (United States)

    Hoyte, Frances; Torr, Jane; Degotardi, Sheila

    2015-01-01

    Friendships and play provide children with opportunities for mutual engagement, which both require and facilitate children's language use. Modality is a semantic system in the language associated with children's learning. One way in which modality is realised is through linguistic expressions which allow speakers to moderate the degree of…

  19. Uncertainty of Modal Parameters Estimated by ARMA Models

    DEFF Research Database (Denmark)

    Jensen, Jakob Laigaard; Brincker, Rune; Rytter, Anders

    In this paper the uncertainties of identified modal parameters such as eigenfrequencies and damping ratios are assessed. From the measured response of dynamic excited structures the modal parameters may be identified and provide important structural knowledge. However the uncertainty of the param...

  20. Constraint programming for modelling and solving modal satisfiability

    NARCIS (Netherlands)

    Brand, S.; Gennari, R.; de Rijke, M.

    2003-01-01

    We explore to what extent and how efficiently constraint programmingcan be used in the context of automated reasoning for modal logics. We encode modal satisfiability problems as constraint satisfactionproblems with non-boolean domains, together with suitable constraints.Experiments show that the

  1. A compositional proof system for the modal μ-calculus

    DEFF Research Database (Denmark)

    Andersen, Henrik Reif; Stirling, C.; Winskel,, G.

    1994-01-01

    We present a proof system for determining satisfaction between processes in a fairly general process algebra and assertions of the modal μ-calculus. The proof system is compositional in the structure of processes. It extends earlier work on compositional reasoning within the modal μ-calculus and ...

  2. Encoding Modality Can Affect Memory Accuracy via Retrieval Orientation

    Science.gov (United States)

    Pierce, Benton H.; Gallo, David A.

    2011-01-01

    Research indicates that false memory is lower following visual than auditory study, potentially because visual information is more distinctive. In the present study we tested the extent to which retrieval orientation can cause a modality effect on memory accuracy. Participants studied unrelated words in different modalities, followed by criterial…

  3. Education Solutions for Child Poverty: New Modalities from New Zealand

    Science.gov (United States)

    Airini

    2015-01-01

    This article describes education solutions to child poverty. Through a focus on New Zealand, the article explores the meaning of child poverty, children's perspectives on child poverty and solutions, and modalities in citizenship, social and economics education to help address child poverty. Four modalities are proposed: centre our work in…

  4. A controls engineering approach for analyzing airplane input-output characteristics

    Science.gov (United States)

    Arbuckle, P. Douglas

    1991-01-01

    An engineering approach for analyzing airplane control and output characteristics is presented. State-space matrix equations describing the linear perturbation dynamics are transformed from physical coordinates into scaled coordinates. The scaling is accomplished by applying various transformations to the system to employ prior engineering knowledge of the airplane physics. Two different analysis techniques are then explained. Modal analysis techniques calculate the influence of each system input on each fundamental mode of motion and the distribution of each mode among the system outputs. The optimal steady state response technique computes the blending of steady state control inputs that optimize the steady state response of selected system outputs. Analysis of an example airplane model is presented to demonstrate the described engineering approach.

  5. Static Structural and Modal Analysis of Gas Turbine Blade

    Science.gov (United States)

    Ranjan Kumar, Ravi; Pandey, K. M., Prof.

    2017-08-01

    Gas turbine is one of the most versatile items of turbo machinery nowadays. It is used in different modes such as power generation, oil and gas, process plants, aviation, domestic and related small industries. This paper is based on the problems concerning blade profile selection, material selection and turbine rotor blade vibration that seriously impact the induced stress-deformation and structural functioning of developmental gas turbine engine. In this paper for generating specific power by rotating blade at specific RPM, blade profile and material has been decided by static structural analysis. Gas turbine rotating blade RPM is decided by Modal Analysis so that the natural frequency of blade should not match with the excitation frequency. For the above blade profile has been modeled in SOLIDWORKS and analysis has been done in ANSYS WORKBENCH 14. Existing NACA6409 profile has been selected as base model and then it is modified by bending it through 72.5° and 145°. Hence these three different blade profiles have been analyzed for three different materials viz. Super Alloy X, Nimonic 80A and Inconel 625 at three different speed viz. 20000, 40000 and 60000RPM. It is found that NACA6409 with 72.5° bent gives best result for all material at all speed. Among all the material Inconel 625 gives best result. Hence Blade of Inconel 625 having 72.5° bent profile is the best combination for all RPM.

  6. Breast US as primary imaging modality for diagnosing gynecomastia.

    Science.gov (United States)

    Telegrafo, M; Introna, T; Coi, L; Cornacchia, I; Rella, L; Stabile Ianora, A A; Angelelli, G; Moschetta, M

    2016-01-01

    To assess the role of breast US in diagnosing and classifying gynecomastia as the primary imaging modality and to compare US findings and classification system with the mammographic ones. 48 patients suspected of having gynecomastia underwent mammography and US. Two radiologists in consensus retrospectively evaluated mammograms and sonograms. Both US and mammographic images were evaluated categorizing gynecomastia into non-mass, nodular and flame shaped patterns. The two category assignations were compared in order to find any difference. The reference standard for both the classification systems was represented by the cytological examination in 18 out of 44 cases (41%) and the six-month US follow-up in the remaining cases. The US examination revealed pseudo-gynecomastia in 4/48 (8%) and true gynecomastia in the remaining 44 (92%). Gynecomastia was bilateral in 25/44 cases (57%) and unilateral in the remaining 19 (43%). The cases of true gynecomastia included non mass shape in 26/44 cases (59%), nodular shape in 12 (27%) and flame shape in 6 (14%). The mammographic examination revealed the same results as compared with US findings. 18/44 (41%) patients affected by nodular or dendritic gynecomastia underwent cytological examination confirming the presence of glandular tissue and the benign nature of the clinical condition. US could be proposed as the primary imaging tool for diagnosing and classifying gynecomastia, avoiding unnecessary Xray examinations or invasive procedures in case of diffuse gynecomastia. In case of nodular or dendritic patterns, biopsy remains mandatory for a definitive diagnosis.

  7. 7 CFR 3430.907 - Stakeholder input.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 15 2010-01-01 2010-01-01 false Stakeholder input. 3430.907 Section 3430.907 Agriculture Regulations of the Department of Agriculture (Continued) COOPERATIVE STATE RESEARCH, EDUCATION, AND EXTENSION SERVICE, DEPARTMENT OF AGRICULTURE COMPETITIVE AND NONCOMPETITIVE NON-FORMULA FEDERAL...

  8. Input and Intake in Language Acquisition

    Science.gov (United States)

    Gagliardi, Ann C.

    2012-01-01

    This dissertation presents an approach for a productive way forward in the study of language acquisition, sealing the rift between claims of an innate linguistic hypothesis space and powerful domain general statistical inference. This approach breaks language acquisition into its component parts, distinguishing the input in the environment from…

  9. A summary of WIMSD4 input option

    International Nuclear Information System (INIS)

    Halsall, M.J.

    1980-07-01

    A description is given of all the available input data options in the ICL 4/70 and IBM 370 versions of WIMSD4, with little more than a reference where there is already adequate documentation but with rather more detail where no such documentation exists. (author)

  10. Representations of space based on haptic input

    NARCIS (Netherlands)

    Zuidhoek, S.

    2005-01-01

    The present thesis focused on the representations of grasping space based on haptic input. We aimed at identifying their characteristics, and the underlying neurocognitive processes and mechanisms. To this end, we studied the systematic distortions in performance on several orientation perception

  11. Hydrogen Generation Rate Model Calculation Input Data

    International Nuclear Information System (INIS)

    KUFAHL, M.A.

    2000-01-01

    This report documents the procedures and techniques utilized in the collection and analysis of analyte input data values in support of the flammable gas hazard safety analyses. This document represents the analyses of data current at the time of its writing and does not account for data available since then

  12. Disaggregated seismic hazard and the elastic input energy spectrum: An approach to design earthquake selection

    Science.gov (United States)

    Chapman, Martin Colby

    1998-12-01

    The design earthquake selection problem is fundamentally probabilistic. Disaggregation of a probabilistic model of the seismic hazard offers a rational and objective approach that can identify the most likely earthquake scenario(s) contributing to hazard. An ensemble of time series can be selected on the basis of the modal earthquakes derived from the disaggregation. This gives a useful time-domain realization of the seismic hazard, to the extent that a single motion parameter captures the important time-domain characteristics. A possible limitation to this approach arises because most currently available motion prediction models for peak ground motion or oscillator response are essentially independent of duration, and modal events derived using the peak motions for the analysis may not represent the optimal characterization of the hazard. The elastic input energy spectrum is an alternative to the elastic response spectrum for these types of analyses. The input energy combines the elements of amplitude and duration into a single parameter description of the ground motion that can be readily incorporated into standard probabilistic seismic hazard analysis methodology. This use of the elastic input energy spectrum is examined. Regression analysis is performed using strong motion data from Western North America and consistent data processing procedures for both the absolute input energy equivalent velocity, (Vsbea), and the elastic pseudo-relative velocity response (PSV) in the frequency range 0.5 to 10 Hz. The results show that the two parameters can be successfully fit with identical functional forms. The dependence of Vsbea and PSV upon (NEHRP) site classification is virtually identical. The variance of Vsbea is uniformly less than that of PSV, indicating that Vsbea can be predicted with slightly less uncertainty as a function of magnitude, distance and site classification. The effects of site class are important at frequencies less than a few Hertz. The regression

  13. Leaders’ receptivity to subordinates’ creative input: the role of achievement goals and composition of creative input

    NARCIS (Netherlands)

    Sijbom, R.B.L.; Janssen, O.; van Yperen, N.W.

    2015-01-01

    We identified leaders’ achievement goals and composition of creative input as important factors that can clarify when and why leaders are receptive to, and supportive of, subordinates’ creative input. As hypothesized, in two experimental studies, we found that relative to mastery goal leaders,

  14. Deep Convolutional Neural Networks for Multi-Modality Isointense Infant Brain Image Segmentation

    Science.gov (United States)

    Zhang, Wenlu; Li, Rongjian; Deng, Houtao; Wang, Li; Lin, Weili; Ji, Shuiwang; Shen, Dinggang

    2015-01-01

    The segmentation of infant brain tissue images into white matter (WM), gray matter (GM), and cerebrospinal fluid (CSF) plays an important role in studying early brain development in health and disease. In the isointense stage (approximately 6–8 months of age), WM and GM exhibit similar levels of intensity in both T1 and T2 MR images, making the tissue segmentation very challenging. Only a small number of existing methods have been designed for tissue segmentation in this isointense stage; however, they only used a single T1 or T2 images, or the combination of T1 and T2 images. In this paper, we propose to use deep convolutional neural networks (CNNs) for segmenting isointense stage brain tissues using multi-modality MR images. CNNs are a type of deep models in which trainable filters and local neighborhood pooling operations are applied alternatingly on the raw input images, resulting in a hierarchy of increasingly complex features. Specifically, we used multimodality information from T1, T2, and fractional anisotropy (FA) images as inputs and then generated the segmentation maps as outputs. The multiple intermediate layers applied convolution, pooling, normalization, and other operations to capture the highly nonlinear mappings between inputs and outputs. We compared the performance of our approach with that of the commonly used segmentation methods on a set of manually segmented isointense stage brain images. Results showed that our proposed model significantly outperformed prior methods on infant brain tissue segmentation. In addition, our results indicated that integration of multi-modality images led to significant performance improvement. PMID:25562829

  15. Influence of lithotripsy modalities on complication rate

    Directory of Open Access Journals (Sweden)

    Radulović Slobodan

    2009-01-01

    Full Text Available Introduction. Localization of ureteric stones and difference in disintegration success are the most important factors in determining the first treatment approach for ureteric stones. Objective. The aim of our study was to evaluate the difference in complication rate between different ureteric stone lithotripsy modalities. Methods. Two hundred sixty patients with ureteric stones were analyzed in a prospective bicentric study that lasted 1 year. The patients were divided into two groups: I - 120 patients who underwent ESWL (extracorporeal shockwave lithotripsy treatment and II - 140 patients who were treated endoscopically with ballistic lithotripsy. Results. Ureteroscopic lithotripsy of all pelvic and iliac stones was significantly more successful comparing to ESWL, while lumbar ureteric stone treatment with ureteroscopic lithotripsy was not significantly more successful than ESWL, except for lumbar stones larger than 100mm2 that were significantly better treated endoscopically. In the I group complications after lithotripsy were recorded in 64 (59.3% and in the II group in 58 (42.0% patients, meaning that complications were statistically significantly more frequent in the I than in the II group. In the II group complications were significantly more often recorded after treatment of proximal comparing to ureteric stones of other localizations, while in the I group complications were significantly more often detected after treatment of impacted stones than in the II group. Conclusion. Being significantly successful comparing to ESWL, ureteric stone treatment with ureteroscopic lithotripsy should be considered as the first therapeutic option for all, especially impacted stones located in the iliac and pelvic ureteric portion. In spite of absent statistical difference in the success rate, ESWL should be chosen as the first treatment option in all cases of lumbar ureteric stones due to lower complication rate except for stones larger than 100mm2 that

  16. Tritium Records to Trace Stratospheric Moisture Inputs in Antarctica

    Science.gov (United States)

    Fourré, E.; Landais, A.; Cauquoin, A.; Jean-Baptiste, P.; Lipenkov, V.; Petit, J.-R.

    2018-03-01

    Better assessing the dynamic of stratosphere-troposphere exchange is a key point to improve our understanding of the climate dynamic in the East Antarctica Plateau, a region where stratospheric inputs are expected to be important. Although tritium (3H or T), a nuclide naturally produced mainly in the stratosphere and rapidly entering the water cycle as HTO, seems a first-rate tracer to study these processes, tritium data are very sparse in this region. We present the first high-resolution measurements of tritium concentration over the last 50 years in three snow pits drilled at the Vostok station. Natural variability of the tritium records reveals two prominent frequencies, one at about 10 years (to be related to the solar Schwabe cycles) and the other one at a shorter periodicity: despite dating uncertainty at this short scale, a good correlation is observed between 3H and Na+ and an anticorrelation between 3H and δ18O measured on an individual pit. The outputs from the LMDZ Atmospheric General Circulation Model including stable water isotopes and tritium show the same 3H-δ18O anticorrelation and allow further investigation on the associated mechanism. At the interannual scale, the modeled 3H variability matches well with the Southern Annular Mode index. At the seasonal scale, we show that modeled stratospheric tritium inputs in the troposphere are favored in winter cold and dry conditions.

  17. Dynamics of a Stage Structured Pest Control Model in a Polluted Environment with Pulse Pollution Input

    OpenAIRE

    Liu, Bing; Xu, Ling; Kang, Baolin

    2013-01-01

    By using pollution model and impulsive delay differential equation, we formulate a pest control model with stage structure for natural enemy in a polluted environment by introducing a constant periodic pollutant input and killing pest at different fixed moments and investigate the dynamics of such a system. We assume only that the natural enemies are affected by pollution, and we choose the method to kill the pest without harming natural enemies. Sufficient conditions for global attractivity ...

  18. Cross-modal Association between Auditory and Visuospatial Information in Mandarin Tone Perception in Noise by Native and Non-native Perceivers

    Directory of Open Access Journals (Sweden)

    Beverly Hannah

    2017-12-01

    Full Text Available Speech perception involves multiple input modalities. Research has indicated that perceivers establish cross-modal associations between auditory and visuospatial events to aid perception. Such intermodal relations can be particularly beneficial for speech development and learning, where infants and non-native perceivers need additional resources to acquire and process new sounds. This study examines how facial articulatory cues and co-speech hand gestures mimicking pitch contours in space affect non-native Mandarin tone perception. Native English as well as Mandarin perceivers identified tones embedded in noise with either congruent or incongruent Auditory-Facial (AF and Auditory-FacialGestural (AFG inputs. Native Mandarin results showed the expected ceiling-level performance in the congruent AF and AFG conditions. In the incongruent conditions, while AF identification was primarily auditory-based, AFG identification was partially based on gestures, demonstrating the use of gestures as valid cues in tone identification. The English perceivers’ performance was poor in the congruent AF condition, but improved significantly in AFG. While the incongruent AF identification showed some reliance on facial information, incongruent AFG identification relied more on gestural than auditory-facial information. These results indicate positive effects of facial and especially gestural input on non-native tone perception, suggesting that cross-modal (visuospatial resources can be recruited to aid auditory perception when phonetic demands are high. The current findings may inform patterns of tone acquisition and development, suggesting how multi-modal speech enhancement principles may be applied to facilitate speech learning.

  19. Modality independence of order coding in working memory: Evidence from cross-modal order interference at recall.

    Science.gov (United States)

    Vandierendonck, André

    2016-01-01

    Working memory researchers do not agree on whether order in serial recall is encoded by dedicated modality-specific systems or by a more general modality-independent system. Although previous research supports the existence of autonomous modality-specific systems, it has been shown that serial recognition memory is prone to cross-modal order interference by concurrent tasks. The present study used a serial recall task, which was performed in a single-task condition and in a dual-task condition with an embedded memory task in the retention interval. The modality of the serial task was either verbal or visuospatial, and the embedded tasks were in the other modality and required either serial or item recall. Care was taken to avoid modality overlaps during presentation and recall. In Experiment 1, visuospatial but not verbal serial recall was more impaired when the embedded task was an order than when it was an item task. Using a more difficult verbal serial recall task, verbal serial recall was also more impaired by another order recall task in Experiment 2. These findings are consistent with the hypothesis of modality-independent order coding. The implications for views on short-term recall and the multicomponent view of working memory are discussed.

  20. Uni-, bi- and tri-modal warning signals: effects of temporal parameters and sensory modality on perceived urgency

    NARCIS (Netherlands)

    van Erp, Johannes Bernardus Fransiscus; Toet, Alexander; Janssen, Joris B.

    Multi-sensory warnings can potentially enhance risk communication. Hereto we investigated how temporal signal parameters affect perceived urgency within and across modalities. In an experiment, 78 observers rated the perceived urgency of uni-, bi-, and/or tri-modal stimuli as function of 25

  1. Uni-, bi- and tri-modal warning signals : Effects of temporal parameters and sensory modality on perceived urgency

    NARCIS (Netherlands)

    Erp, J.B.F. van; Toet, A.; Janssen, J.B.

    2015-01-01

    Multi-sensory warnings can potentially enhance risk communication. Hereto we investigated how temporal signal parameters affect perceived urgency within and across modalities. In an experiment, 78 observers rated the perceived urgency of uni-, bi-, and/or tri-modal stimuli as function of 25

  2. Using Learning Modalities to Celebrate Intelligence.

    Science.gov (United States)

    Samples, Bob

    1992-01-01

    Jerome Bruner identified three major ways of knowing: iconic, enactive, and symbolic. Schooling has been dominantly framed in the symbolic, and intelligence and achievement were measured in this realm. Gregory Bateson, concerned with mind-nature separation, differentiated between the map (a human-made abstraction) and the territory (the natural…

  3. Modal Characterization of a Piezoelectric Shaker Table

    Science.gov (United States)

    2015-06-01

    actuated shaker tables are often used for high frequency fatigue testing. Since natural frequencies can appear in the operating range of these...course of this thesis effort. I would also like to thank Dr. Tommy George and all of the helpful people in the Turbine Engine Fatigue Facility at the...4 Figure 2. Perovskite Crystal Structure of PZT Ceramics ................................................... 5 Figure 3

  4. A new procedure of modal parameter estimation for high-speed digital image correlation

    Science.gov (United States)

    Huňady, Róbert; Hagara, Martin

    2017-09-01

    The paper deals with the use of 3D digital image correlation in determining modal parameters of mechanical systems. It is a non-contact optical method, which for the measurement of full-field spatial displacements and strains of bodies uses precise digital cameras with high image resolution. Most often this method is utilized for testing of components or determination of material properties of various specimens. In the case of using high-speed cameras for measurement, the correlation system is capable of capturing various dynamic behaviors, including vibration. This enables the potential use of the mentioned method in experimental modal analysis. For that purpose, the authors proposed a measuring chain for the correlation system Q-450 and developed a software application called DICMAN 3D, which allows the direct use of this system in the area of modal testing. The created application provides the post-processing of measured data and the estimation of modal parameters. It has its own graphical user interface, in which several algorithms for the determination of natural frequencies, mode shapes and damping of particular modes of vibration are implemented. The paper describes the basic principle of the new estimation procedure which is crucial in the light of post-processing. Since the FRF matrix resulting from the measurement is usually relatively large, the estimation of modal parameters directly from the FRF matrix may be time-consuming and may occupy a large part of computer memory. The procedure implemented in DICMAN 3D provides a significant reduction in memory requirements and computational time while achieving a high accuracy of modal parameters. Its computational efficiency is particularly evident when the FRF matrix consists of thousands of measurement DOFs. The functionality of the created software application is presented on a practical example in which the modal parameters of a composite plate excited by an impact hammer were determined. For the

  5. Natural asynchronies in audiovisual communication signals regulate neuronal multisensory interactions in voice-sensitive cortex.

    Science.gov (United States)

    Perrodin, Catherine; Kayser, Christoph; Logothetis, Nikos K; Petkov, Christopher I

    2015-01-06

    When social animals communicate, the onset of informative content in one modality varies considerably relative to the other, such as when visual orofacial movements precede a vocalization. These naturally occurring asynchronies do not disrupt intelligibility or perceptual coherence. However, they occur on time scales where they likely affect integrative neuronal activity in ways that have remained unclear, especially for hierarchically downstream regions in which neurons exhibit temporally imprecise but highly selective responses to communication signals. To address this, we exploited naturally occurring face- and voice-onset asynchronies in primate vocalizations. Using these as stimuli we recorded cortical oscillations and neuronal spiking responses from functional MRI (fMRI)-localized voice-sensitive cortex in the anterior temporal lobe of macaques. We show that the onset of the visual face stimulus resets the phase of low-frequency oscillations, and that the face-voice asynchrony affects the prominence of two key types of neuronal multisensory responses: enhancement or suppression. Our findings show a three-way association between temporal delays in audiovisual communication signals, phase-resetting of ongoing oscillations, and the sign of multisensory responses. The results reveal how natural onset asynchronies in cross-sensory inputs regulate network oscillations and neuronal excitability in the voice-sensitive cortex of macaques, a suggested animal model for human voice areas. These findings also advance predictions on the impact of multisensory input on neuronal processes in face areas and other brain regions.

  6. Higher order visual input to the mushroom bodies in the bee, Bombus impatiens.

    Science.gov (United States)

    Paulk, Angelique C; Gronenberg, Wulfila

    2008-11-01

    To produce appropriate behaviors based on biologically relevant associations, sensory pathways conveying different modalities are integrated by higher-order central brain structures, such as insect mushroom bodies. To address this function of sensory integration, we characterized the structure and response of optic lobe (OL) neurons projecting to the calyces of the mushroom bodies in bees. Bees are well known for their visual learning and memory capabilities and their brains possess major direct visual input from the optic lobes to the mushroom bodies. To functionally characterize these visual inputs to the mushroom bodies, we recorded intracellularly from neurons in bumblebees (Apidae: Bombus impatiens) and a single neuron in a honeybee (Apidae: Apis mellifera) while presenting color and motion stimuli. All of the mushroom body input neurons were color sensitive while a subset was motion sensitive. Additionally, most of the mushroom body input neurons would respond to the first, but not to subsequent, presentations of repeated stimuli. In general, the medulla or lobula neurons projecting to the calyx signaled specific chromatic, temporal, and motion features of the visual world to the mushroom bodies, which included sensory information required for the biologically relevant associations bees form during foraging tasks.

  7. Modal Arguments against Physicalism in View of Scientific Findings Concerning Pain

    Directory of Open Access Journals (Sweden)

    Maja Malec

    2017-10-01

    Full Text Available I analyse Kripke's modal argument against the mind-brain identity theories. Specifically, he argues against the identity between pain and C-fibres simulation by pointing out the difference between this identity claim and the theoretical identifications, such as 'Water is H2O' and 'Lightning is a motion of electric charges'. Kripke's argument relies on the assumption that the experience of pains is a simple and homogenous phenomenon, but scientific research shows that it is in fact a quite complex one. We can distinguish at least three components: sensory-discriminative, motivational-affective and cognitive. This discovery makes it possible to reject Kripke's argument, but it also uncovers a major flaw that is common to all modal arguments against physicalism. They proclaim to answer the fundamental question about the nature of our world by relying on our powers of imagination and without having the relevant factual knowledge.

  8. Operational modal analysis and wavelet transformation for damage identification in wind turbine blades

    DEFF Research Database (Denmark)

    Ulriksen, Martin Dalgaard; Tcherniak, Dmitri; Kirkegaard, Poul Henning

    2014-01-01

    The presented study demonstrates an application of a previously proposed modal and wavelet analysis-based damage identification method to a wind turbine blade. A trailing edge debonding was introduced to a SSP 34m blade mounted on a test rig. Operational modal analysis (OMA) was conducted to obtain...... are captured in the CWT by significantly magnified transform coefficients, thus providing combined damage detection, localization, and size assessment. It was found that due to the nature of the proposed method, the value of the identification results highly depends on the number of employed measurement points....... Since only a limited number of measurement points were utilized in the experiments, valid damage identification can only be obtained when employing high-frequency modes....

  9. Evaluation of freeze-thaw durability of pervious concrete by use of operational modal analysis

    DEFF Research Database (Denmark)

    Lund, M.S.M.; Hansen, K. K.; Brincker, R.

    2018-01-01

    It is well-known that laboratory testing of pervious concrete's freeze-thaw performance is too harsh and does not agree well with field observations. The most commonly used laboratory freeze-thaw test method for pervious concrete is similar to that used for conventional concrete even though...... the void structure of the two materials is completely different. In the present study, a new freeze-thaw test method for pervious concrete is suggested and tested on one baseline mix, with three different contents of entrained air. The evaluation of freeze-thaw damage on pervious concrete beams...... was evaluated from the decrease in mass and from operational modal analysis which provides an accurate determination of the change in natural frequencies with freeze-thaw exposure. Operational modal analysis was also used to determine the Young's modulus, shear modulus, and Poisson's ratio of the pervious...

  10. Variation of Modal Characteristics of Electrical Cabinet According to the Excitation Level in Impact Hammer Test

    International Nuclear Information System (INIS)

    Cho, Sung Gook; So, Gi Hwan; Kim, Doo Kie

    2010-01-01

    There are many electrical cabinets in nuclear power plants. Safety-related equipment is typically seismic qualified before installation. Seismic qualification of equipment is possible when identifying the accurate dynamic characteristics of the equipment. According to the nature of the cabinet, the dynamic characteristics of the electrical cabinet vary nonlinearly with excitation level. This study analyzed the nonlinear variation of the dynamic properties of an actual cabinet. For the purpose of this study, a seismic monitoring system cabinet was selected as a specimen. The impact hammer tests were conducted to identify a variation of the dynamic characteristics of the specimen by increasing the impulse level. Modal identification technique was used to extract the modal properties of the cabinet from the measurements

  11. Sub-threshold cross-modal sensory interaction in the thalamus: lemniscal auditory response in the medial geniculate nucleus is modulated by somatosensory stimulation.

    Science.gov (United States)

    Donishi, T; Kimura, A; Imbe, H; Yokoi, I; Kaneoke, Y

    2011-02-03

    Recent studies have highlighted cross-modal sensory modulations in the primary sensory areas in the cortex, suggesting that cross-modal sensory interactions occur at early stages in the hierarchy of sensory processing. Multi-modal sensory inputs from non-lemniscal thalamic nuclei and cortical inputs from the secondary sensory and association areas are considered responsible for the modulations. On the other hand, there is little evidence of cross-sensory modal sensitivities in lemniscal thalamic nuclei. In the present study, we were interested in a possibility that somatosensory stimulation may affect auditory response in the ventral division (MGV) of the medial geniculate nucleus (MG), a lemniscal thalamic nucleus that is considered to be dedicated to auditory uni-modal processing. Experiments were performed on anesthetized rats. Transcutaneous electrical stimulation of the hindpaw, which is thought to evoke nociception and seems unrelated to auditory processing, modulated unit discharges in response to auditory stimulation (noise bursts). The modulation was observed in the MGV and non-lemniscal auditory thalamic nuclei such as the dorsal and medial divisions of the MG. The major effect of somatosensory stimulation was suppression. The most robust suppression was induced by electrical stimuli given simultaneously with noise bursts or preceding noise bursts by 10 to 20 ms. The results indicate that the lemniscal (MGV) and non-lemniscal auditory nuclei are subject to somatosensory influence. In everyday experience intense somatosensory stimuli such as pain interrupt our ongoing hearing or interfere with clear recognition of sound. The modulation of lemniscal auditory response by somatosensory stimulation may underlie such cross-modal disturbance of auditory perception as a form of cross-modal switching of attention. Copyright © 2011 IBRO. Published by Elsevier Ltd. All rights reserved.

  12. Simulating Marine New Particle Formation and Growth Using the M7 Modal Aerosol Dynamics Modal

    Directory of Open Access Journals (Sweden)

    Ciaran Monahan

    2010-01-01

    Full Text Available A modal atmospheric aerosol model (M7 is evaluated in terms of predicting marine new particle formation and growth. Simulations were carried out for three different nucleation schemes involving (1 kinetic self-nucleation of OIO (2 nucleation via OIO activation by H2SO4 and (3 nucleation via OIO activation by H2SO4 plus condensation of a low-volatility organic vapour. Peak OIO and H2SO4 vapour concentrations were both limited to 6×106 molecules cm-3 at noontime while the peak organic vapour concentration was limited to 12×106 molecules cm-3. All simulations produced significant concentrations of new particles in the Aitken mode. From a base case particle concentration of 222 cm-3 at radii >15 nm, increases in concentrations to 366 cm-3 were predicted from the OIO-OIO case, 722 cm-3 for the OIO-H2SO4 case, and 1584 cm-3 for the OIO-H2SO4 case with additional condensing organic vapours. The results indicate that open ocean new particle production is feasible for clean conditions; however, new particle production becomes most significant when an additional condensable organic vapour is available to grow the newly formed particles to larger sizes. Comparison to sectional model for a typical case study demonstrated good agreement and the validity of using the modal model.

  13. Verifying different-modality properties for concepts produces switching costs.

    Science.gov (United States)

    Pecher, Diane; Zeelenberg, René; Barsalou, Lawrence W

    2003-03-01

    According to perceptual symbol systems, sensorimotor simulations underlie the representation of concepts. It follows that sensorimotor phenomena should arise in conceptual processing. Previous studies have shown that switching from one modality to another during perceptual processing incurs a processing cost. If perceptual simulation underlies conceptual processing, then verifying the properties of concepts should exhibit a switching cost as well. For example, verifying a property in the auditory modality (e.g., BLENDER-loud) should be slower after verifying a property in a different modality (e.g., CRANBERRIES-tart) than after verifying a property in the same modality (e.g., LEAVES-rustling). Only words were presented to subjects, and there were no instructions to use imagery. Nevertheless, switching modalities incurred a cost, analogous to the cost of switching modalities in perception. A second experiment showed that this effect was not due to associative priming between properties in the same modality. These results support the hypothesis that perceptual simulation underlies conceptual processing.

  14. Analysis of modal frequency optimization of railway vehicle car body

    Directory of Open Access Journals (Sweden)

    Wenjing Sun

    2016-04-01

    Full Text Available High structural modal frequencies of car body are beneficial as they ensure better vibration control and enhance ride quality of railway vehicles. Modal sensitivity optimization and elastic suspension parameters used in the design of equipment beneath the chassis of the car body are proposed in order to improve the modal frequencies of car bodies under service conditions. Modal sensitivity optimization is based on sensitivity analysis theory which considers the thickness of the body frame at various positions as variables in order to achieve optimization. Equipment suspension design analyzes the influence of suspension parameters on the modal frequencies of the car body through the use of an equipment-car body coupled model. Results indicate that both methods can effectively improve the modal parameters of the car body. Modal sensitivity optimization increases vertical bending frequency from 9.70 to 10.60 Hz, while optimization of elastic suspension parameters increases the vertical bending frequency to 10.51 Hz. The suspension design can be used without alteration to the structure of the car body while ensuring better ride quality.

  15. Do efficiency scores depend on input mix?

    DEFF Research Database (Denmark)

    Asmild, Mette; Hougaard, Jens Leth; Kronborg, Dorte

    2013-01-01

    In this paper we examine the possibility of using the standard Kruskal-Wallis (KW) rank test in order to evaluate whether the distribution of efficiency scores resulting from Data Envelopment Analysis (DEA) is independent of the input (or output) mix of the observations. Since the DEA frontier...... is estimated, many standard assumptions for evaluating the KW test statistic are violated. Therefore, we propose to explore its statistical properties by the use of simulation studies. The simulations are performed conditional on the observed input mixes. The method, unlike existing approaches...... the assumption of mix independence is rejected the implication is that it, for example, is impossible to determine whether machine intensive project are more or less efficient than labor intensive projects....

  16. Application of computer voice input/output

    International Nuclear Information System (INIS)

    Ford, W.; Shirk, D.G.

    1981-01-01

    The advent of microprocessors and other large-scale integration (LSI) circuits is making voice input and output for computers and instruments practical; specialized LSI chips for speech processing are appearing on the market. Voice can be used to input data or to issue instrument commands; this allows the operator to engage in other tasks, move about, and to use standard data entry systems. Voice synthesizers can generate audible, easily understood instructions. Using voice characteristics, a control system can verify speaker identity for security purposes. Two simple voice-controlled systems have been designed at Los Alamos for nuclear safeguards applicaations. Each can easily be expanded as time allows. The first system is for instrument control that accepts voice commands and issues audible operator prompts. The second system is for access control. The speaker's voice is used to verify his identity and to actuate external devices

  17. Spatial Analysis of Case-Mix and Dialysis Modality Associations.

    Science.gov (United States)

    Phirtskhalaishvili, Tamar; Bayer, Florian; Edet, Stephane; Bongiovanni, Isabelle; Hogan, Julien; Couchoud, Cécile

    2016-01-01

    ♦ Health-care systems must attempt to provide appropriate, high-quality, and economically sustainable care that meets the needs and choices of patients with end-stage renal disease (ESRD). France offers 9 different modalities of dialysis, each characterized by dialysis technique, the extent of professional assistance, and the treatment site. The aim of this study was 1) to describe the various dialysis modalities in France and the patient characteristics associated with each of them, and 2) to analyze their regional patterns to identify possible unexpected associations between case-mixes and dialysis modalities. ♦ The clinical characteristics of the 37,421 adult patients treated by dialysis were described according to their treatment modality. Agglomerative hierarchical cluster analysis was used to aggregate the regions into clusters according to their use of these modalities and the characteristics of their patients. ♦ The gradient of patient characteristics was similar from home hemodialyis (HD) to in-center HD and from non-assisted automated peritoneal dialysis (APD) to assisted continuous ambulatory peritoneal dialysis (CAPD). Analyzing their spatial distribution, we found differences in the patient case-mix on dialysis across regions but also differences in the health-care provided for them. The classification of the regions into 6 different clusters allowed us to detect some unexpected associations between case-mixes and treatment modalities. ♦ The 9 modalities of treatment available make it theoretically possible to adapt treatment to patients' clinical characteristics and abilities. However, although we found an overall appropriate association of dialysis modalities to the case-mix, major inter-region heterogeneity and the low rate of peritoneal dialysis (PD) and home HD suggest that factors besides patients' clinical conditions impact the choice of dialysis modality. The French organization should now be evaluated in terms of patients' quality of

  18. Material model of pelvic bone based on modal analysis: a study on the composite bone.

    Science.gov (United States)

    Henyš, Petr; Čapek, Lukáš

    2017-02-01

    Digital models based on finite element (FE) analysis are widely used in orthopaedics to predict the stress or strain in the bone due to bone-implant interaction. The usability of the model depends strongly on the bone material description. The material model that is most commonly used is based on a constant Young's modulus or on the apparent density of bone obtained from computer tomography (CT) data. The Young's modulus of bone is described in many experimental works with large variations in the results. The concept of measuring and validating the material model of the pelvic bone based on modal analysis is introduced in this pilot study. The modal frequencies, damping, and shapes of the composite bone were measured precisely by an impact hammer at 239 points. An FE model was built using the data pertaining to the geometry and apparent density obtained from the CT of the composite bone. The isotropic homogeneous Young's modulus and Poisson's ratio of the cortical and trabecular bone were estimated from the optimisation procedure including Gaussian statistical properties. The performance of the updated model was investigated through the sensitivity analysis of the natural frequencies with respect to the material parameters. The maximal error between the numerical and experimental natural frequencies of the bone reached 1.74 % in the first modal shape. Finally, the optimised parameters were matched with the data sheets of the composite bone. The maximal difference between the calibrated material properties and that obtained from the data sheet was 34 %. The optimisation scheme of the FE model based on the modal analysis data provides extremely useful calibration of the FE models with the uncertainty bounds and without the influence of the boundary conditions.

  19. PREP-45, Input Preparation for CITATION-2

    International Nuclear Information System (INIS)

    Ramalho Carlos, C.A.

    1995-01-01

    1 - Description of program or function: A Fortran program has been created, which saves much effort in preparing sections 004 (intervals in the coordinates) and 005 (zone numbers) of the input data file for the multigroup theory code CITATION (version CITATION-2, NESC0387/09), particularly when a thin complicated mesh is used. 2 - Method of solution: A domain is defined for CITATION calculations through specifying its sub-domains (e.g. graphite, lead, beryllium, water and fuel sub-domains) in a compact and simple way. An independent and previous geometrical specification is made of the various types of elements which are envisaged to constitute the contents of the reactor core grid positions. Then the load table for the configuration is input and scanned throughout, thus enabling the geometric mesh description to be produced (section 004). Also the zone placement (section 005) is achieved by means of element description subroutines for the different types of element (which may require appropriate but simple changes in the actual cases). The output of PREP45 is directly obtained in a format which is compatible with CITATION-2 input. 3 - Restrictions on the complexity of the problem: Only rectangular two-dimensional Cartesian coordinates are considered. A maximum of 12 sub-domains in the x direction (18 in the y direction) and up to 8 distinct element types are considered in this version. Other limitations exist which can nevertheless be overcome with simple changes in the source program

  20. Molecular structure input on the web

    Directory of Open Access Journals (Sweden)

    Ertl Peter

    2010-02-01

    Full Text Available Abstract A molecule editor, that is program for input and editing of molecules, is an indispensable part of every cheminformatics or molecular processing system. This review focuses on a special type of molecule editors, namely those that are used for molecule structure input on the web. Scientific computing is now moving more and more in the direction of web services and cloud computing, with servers scattered all around the Internet. Thus a web browser has become the universal scientific user interface, and a tool to edit molecules directly within the web browser is essential. The review covers a history of web-based structure input, starting with simple text entry boxes and early molecule editors based on clickable maps, before moving to the current situation dominated by Java applets. One typical example - the popular JME Molecule Editor - will be described in more detail. Modern Ajax server-side molecule editors are also presented. And finally, the possible future direction of web-based molecule editing, based on technologies like JavaScript and Flash, is discussed.

  1. Look Who's Talking: Speech Style and Social Context in Language Input to Infants Are Linked to Concurrent and Future Speech Development

    Science.gov (United States)

    Ramírez-Esparza, Nairán; García-Sierra, Adrián; Kuhl, Patricia K.

    2014-01-01

    Language input is necessary for language learning, yet little is known about whether, in natural environments, the speech style and social context of language input to children impacts language development. In the present study we investigated the relationship between language input and language development, examining both the style of parental…

  2. A Logical Approach to Modal Verbs 3. “Must”

    Directory of Open Access Journals (Sweden)

    Imre Attila

    2017-12-01

    Full Text Available The article aims at a logical approach to discussing must, organized around the core meaning of necessity, split into epistemic (logical necessity and deontic necessity (obligation. After discussing must as a central modal auxiliary, we present various meanings of must, relying on authoritative sources published for international (English, Hungarian, and Romanian students. Possible issues of teaching must are also dealt with, supported by data from a popular TV series containing modal verbs. The conclusion discusses the importance and relativity of a number of occurrences, trying to offer a possible teaching option for modals stemming from practice.

  3. Modal Ring Method for the Scattering of Electromagnetic Waves

    Science.gov (United States)

    Baumeister, Kenneth J.; Kreider, Kevin L.

    1993-01-01

    The modal ring method for electromagnetic scattering from perfectly electric conducting (PEC) symmetrical bodies is presented. The scattering body is represented by a line of finite elements (triangular) on its outer surface. The infinite computational region surrounding the body is represented analytically by an eigenfunction expansion. The modal ring method effectively reduces the two dimensional scattering problem to a one-dimensional problem similar to the method of moments. The modal element method is capable of handling very high frequency scattering because it has a highly banded solution matrix.

  4. Modal noise impact in radio over fiber multimode fiber links.

    Science.gov (United States)

    Gasulla, I; Capmany, J

    2008-01-07

    A novel analysis is given on the statistics of modal noise for a graded-index multimode fiber (MMF) link excited by an analog intensity modulated laser diode. We present the speckle contrast as a function of the power spectrum of the modulated source and the transfer function of the MMF which behaves as an imperfect transversal microwave photonic filter. The theoretical results confirm that the modal noise is directly connected with the coherence properties of the optical source and show that the performance of high-frequency Radio Over Fiber (ROF) transmission through MMF links for short and middle reach distances is not substantially degraded by modal noise.

  5. An operational modal analysis method in frequency and spatial domain

    Science.gov (United States)

    Wang, Tong; Zhang, Lingmi; Tamura, Yukio

    2005-12-01

    A frequency and spatial domain decomposition method (FSDD) for operational modal analysis (OMA) is presented in this paper, which is an extension of the complex mode indicator function (CMIF) method for experimental modal analysis (EMA). The theoretical background of the FSDD method is clarified. Singular value decomposition is adopted to separate the signal space from the noise space. Finally, an enhanced power spectrum density (PSD) is proposed to obtain more accurate modal parameters by curve fitting in the frequency domain. Moreover, a simulation case and an application case are used to validate this method.

  6. Treatment modalities for hyperpigmented skin lesions: A brief overview

    Directory of Open Access Journals (Sweden)

    Yan Teng Khoo

    2016-07-01

    Full Text Available Skin hyperpigmentation involves a broad range of skin conditions, including epidermal pigmented lesions, dermal pigmented lesions, and mixed pigmented lesions. Treatment includes various modalities such as brightening cream, chemical peeling, and laser therapy. Responses to various treatment modalities can be quite varied depending on the type of treatment and the degree of pigmentation. Sometimes a lesion can lighten or even partially disappear, while other lesions may recur. This paper provides a brief overview of treatment modalities available for hyperpigmented skin lesions including the importance of photoprotection, various types of brightening creams, suitable types of chemical peels, specific laser therapies targeted for skin hyperpigmentation, and surgery.

  7. Damage detection in concrete precast slabs: a quick assessment through modal tests

    Directory of Open Access Journals (Sweden)

    Leal Pimentel Roberto

    2015-01-01

    Full Text Available The use of modal tests for detecting damage in reinforced concrete precast slabs is evaluated. A set of eight slabs were tested, each belonging to flats constructed for residential use. Two groups of slabs were identified and, in each group, both cracked and uncracked slabs were found. This made it possible to compare the responses of the slabs when subjected to modal tests. The tests were carried out employing an instrumented hammer and heel drops as excitation sources. Responses were measured using an accelerometer. The lowest natural frequencies of the slabs could be identified and after filtering the results, plots indicating the variation of the lowest natural frequency versus the number of cycles of free decay were obtained for each slab. Such a plot is of more general use than the value of the natural frequency by itself, as it does not depend on slab configuration. It was observed that the cracked slabs presented a similar pattern of variation of the natural frequencies throughout the decay, being distinctive from the pattern observed for their uncracked counterparts. This provided evidence that a quick assessment of the structural condition of such slabs through the use of the tests were feasible.

  8. PERANAN INVESTASI PENANAMAN MODAL DALAM NEGRI (PMDN DAN PENANAMAN MODAL ASING (PMA DALAM PENYERAPAN TENAGA KERJA DI KABUPATEN SIAK

    Directory of Open Access Journals (Sweden)

    Muhammad Thamrin

    2016-10-01

    Full Text Available Abstrak: Siak yang kita kenal sebagai salah satu daerah potensi sumber daya alam yang dimilikinya dan juga dikenal sebagai salah satu tujuan wisata di Provinsi Riau. pembangunan ekonomi Siak berdasarkan kebutuhan sumber daya alam dan sumber daya manusia yang potensial, dan karena itu potensi ini perlu dikelola dan dimanfaatkan karena dapat membuat kontribusi besar untuk negara untuk menarik investasi serta menciptakan lapangan kerja. investasi mereka akan mendorong terciptanya barang modal baru yang akan menyerap faktor produksi baru yang menciptakan lapangan kerja kerjabaru atau pekerjaan yang akan menyerap tenaga kerja, yang pada gilirannya akan mengurangi pengangguran.               Berdasarkan apa yang telah dijelaskan, penyidik permasalahandalam pokok merumuskan penelitian ini adalah, Barapa besar adalah peran investasi domestik dan asing untuk menyerap permintaan tenaga kerja di Siak. Setelah semua data yang diperlukan dikumpulkan, diproses, dan kemudian dianalisis menggunakan metode deskriptif berdasarkan teori, model dan berbagai pendapat para ahli yang sudah berlaku umum sesuai dengan masalah yang dibahas.               Hasil penelitian menunjukkan Siak merupakan salah satu daerah potensi sumber daya alam, potensi terbesar Kabupaten Siak adalah pertanian dan perkebunan, Foreign Direct Investment (FDI yang terjadi selama lima tahun terakhir sebesar Rp 7.508.886.293.818, - atau 43, 40% yang terutama terlibat sektor industri, ada dua (2 perusahaan yang berinvestasi besar, yaitu PT. Indah Kiat Pulp & Paper Tbk dan PT. Pindo Deli Pulp & Paper Mills mampu menyerap tenaga kerja sebanya 22 168 orang atau 13,41%. Penanaman Modal Dalam Negeri (PMDN dalam lima tahun terakhir sebesar Rp 9.839.746.586.566, - atau 56,60%, yang bergerak di sektor pertanian dan perkebunan sektor manufaktur mampu menyediakan lapangan kerja bagi 143 172 orang atau 86,59%.  Abstract: Siak we know as one of the potential of its natural

  9. Categorical Inputs, Sensitivity Analysis, Optimization and Importance Tempering with tgp Version 2, an R Package for Treed Gaussian Process Models

    Directory of Open Access Journals (Sweden)

    Robert B. Gramacy

    2010-02-01

    Full Text Available This document describes the new features in version 2.x of the tgp package for R, implementing treed Gaussian process (GP models. The topics covered include methods for dealing with categorical inputs and excluding inputs from the tree or GP part of the model; fully Bayesian sensitivity analysis for inputs/covariates; sequential optimization of black-box functions; and a new Monte Carlo method for inference in multi-modal posterior distributions that combines simulated tempering and importance sampling. These additions extend the functionality of tgp across all models in the hierarchy: from Bayesian linear models, to classification and regression trees (CART, to treed Gaussian processes with jumps to the limiting linear model. It is assumed that the reader is familiar with the baseline functionality of the package, outlined in the first vignette (Gramacy 2007.

  10. Dynamic behaviour studies of a vertical axis wind turbine blade using Operational Modal Analysis (OMA) and Experimental Modal Analysis (EMA)

    DEFF Research Database (Denmark)

    Najafi, Nadia; Schmidt Paulsen, Uwe; Belloni, F.

    2014-01-01

    Dynamic behavior of a modified blade fitted onto a small 1 kW vertical-axis wind turbine is studied by two different approaches: Classical modal analysis (EMA) is carried out to validate the results of Operational Modal Analysis (OMA). In traditional modal analysis (EMA) one axis accelerometers...... it is excited by random and wind forces. The cameras are programmed in LabView to take pictures at the same time with 180 fps and store them on a high speed hard disk. The output deflection will be investigated in frequency domain by peak picking method, and then AR (Autoregressive) model is applied to describe...

  11. Stimulus Modality and Smoking Behavior: Moderating Role of Implicit Attitudes.

    Science.gov (United States)

    Ezeh, Valentine C; Mefoh, Philip

    2015-07-20

    This study investigated whether stimulus modality influences smoking behavior among smokers in South Eastern Nigeria and also whether implicit attitudes moderate the relationship between stimulus modality and smoking behavior. 60 undergraduate students of University of Nigeria, Nsukka were used. Participants were individually administered the IAT task as a measure of implicit attitude toward smoking and randomly assigned into either image condition that paired images of cigarette with aversive images of potential health consequences or text condition that paired images of cigarette with aversive texts of potential health consequences. A one- predictor and one-moderator binary logistic analysis indicates that stimulus modality significantly predicts smoking behavior (p = smoke with greater probability than the text condition. The interaction between stimulus modality and IAT scores was also significant (p = attitudes towards smoking. The finding shows the urgent need to introduce the use of aversive images of potential health consequences on cigarette packs in Nigeria.

  12. Statistical approach for uncertainty quantification of experimental modal model parameters

    DEFF Research Database (Denmark)

    Luczak, M.; Peeters, B.; Kahsin, M.

    2014-01-01

    Composite materials are widely used in manufacture of aerospace and wind energy structural components. These load carrying structures are subjected to dynamic time-varying loading conditions. Robust structural dynamics identification procedure impose tight constraints on the quality of modal models...... represent different complexity levels ranging from coupon, through sub-component up to fully assembled aerospace and wind energy structural components made of composite materials. The proposed method is demonstrated on two application cases of a small and large wind turbine blade........ This paper aims at a systematic approach for uncertainty quantification of the parameters of the modal models estimated from experimentally obtained data. Statistical analysis of modal parameters is implemented to derive an assessment of the entire modal model uncertainty measure. Investigated structures...

  13. Multi-Modal Intelligent Traffic Signal Systems GPS

    Data.gov (United States)

    Department of Transportation — Data were collected during the Multi-Modal Intelligent Transportation Signal Systems (MMITSS) study. MMITSS is a next-generation traffic signal system that seeks to...

  14. Modal interval analysis new tools for numerical information

    CERN Document Server

    Sainz, Miguel A; Calm, Remei; Herrero, Pau; Jorba, Lambert; Vehi, Josep

    2014-01-01

    This book presents an innovative new approach to interval analysis. Modal Interval Analysis (MIA) is an attempt to go beyond the limitations of classic intervals in terms of their structural, algebraic and logical features. The starting point of MIA is quite simple: It consists in defining a modal interval that attaches a quantifier to a classical interval and in introducing the basic relation of inclusion between modal intervals by means of the inclusion of the sets of predicates they accept. This modal approach introduces interval extensions of the real continuous functions, identifies equivalences between logical formulas and interval inclusions, and provides the semantic theorems that justify these equivalences, along with guidelines for arriving at these inclusions. Applications of these equivalences in different areas illustrate the obtained results. The book also presents a new interval object: marks, which aspire to be a new form of numerical treatment of errors in measurements and computations.

  15. Mixing Categories and Modal Logics in the Quantum Setting

    Science.gov (United States)

    Cinà, Giovanni

    The study of the foundations of Quantum Mechanics, especially after the advent of Quantum Computation and Information, has benefited from the application of category-theoretic tools and modal logics to the analysis of Quantum processes: we witness a wealth of theoretical frameworks casted in either of the two languages. This paper explores the interplay of the two formalisms in the peculiar context of Quantum Theory. After a review of some influential abstract frameworks, we show how different modal logic frames can be extracted from the category of finite dimensional Hilbert spaces, connecting the Categorical Quantum Mechanics approach to some modal logics that have been proposed for Quantum Computing. We then apply a general version of the same technique to two other categorical frameworks, the `topos approach' of Doering and Isham and the sheaf-theoretic work on contextuality by Abramsky and Brandenburger, suggesting how some key features can be expressed with modal languages.

  16. Modal and Mixed Specifications: Key Decision Problems and their Complexities

    DEFF Research Database (Denmark)

    Antonik, Adam; Huth, Michael; Larsen, Kim Guldstrand

    2010-01-01

    , and whether all implementations of one specification are implementations of another one. For each of these decision problems we investigate the worst-case computational complexity for the modal and mixed case. We show that the first decision problem is EXPTIME-complete for modal as well as for mixed......Modal and mixed transition systems are specification formalisms that allow mixing of over- and under-approximation. We discuss three fundamental decision problems for such specifications: whether a set of specifications has a common implementation, whether a sole specification has an implementation...... specifications. We prove that the second decision problem is EXPTIME-complete for mixed specifications (while it is known to be trivial for modal ones). The third decision problem is furthermore demonstrated to be EXPTIME-complete for mixed specifications....

  17. Cross-modal project prioritization : a TPCB peer exchange.

    Science.gov (United States)

    2015-05-01

    This report highlights key recommendations and best practices identified at the peer exchange on Cross-Modal Project Prioritization, held on December 16 and 17, 2014, in Raleigh, North Carolina. This event was sponsored by the Transportation Planning...

  18. Multi-Modal Traveler Information System - Gateway Functional Requirements

    Science.gov (United States)

    1997-11-17

    The Multi-Modal Traveler Information System (MMTIS) project involves a large number of Intelligent Transportation System (ITS) related tasks. It involves research of all ITS initiatives in the Gary-Chicago-Milwaukee (GCM) Corridor which are currently...

  19. Modal functions. Properties and application for simulation of subject regions

    International Nuclear Information System (INIS)

    Rudkevich, A.V.

    1988-01-01

    New type of information structures for simulation of undefined information in information retrieval systems is suggested. Main properties of modal functions have been proved. Algorithm of their applications for data retrieval is presented. 9 refs

  20. The measurement of the modal strain fields using digital shearography

    Directory of Open Access Journals (Sweden)

    Gomes J.M.

    2010-06-01

    Full Text Available This work presents a Michelson shearography interferometer configuration associated with stroboscopic double illumination technique for the measurement of modal rotation fields and their strain fields on a clamped circular aluminium plate. The speckle pattern is frozen by the synchronization between the LASER illumination and the modal vibration of the object. The quantitative evaluation is performed for each digital shearogram using a time modulation technique. The setup of double illumination LASER with out-of-plane opposite sensitivity allows the two phase maps measurement of the modal spatial gradient. The modal rotation and strain fields are extracted by the combination of this two digital phase maps. Image processing techniques are applied on the phase maps to obtain full-field measurements using a dedicated post-processing algorithm. Finally, is presented a comparison between the experimental measurement and the numerical solution.

  1. Modality dependency of familiarity ratings of Japanese words.

    Science.gov (United States)

    Amano, S; Kondo, T; Kakehi, K

    1995-07-01

    Familiarity ratings for a large number of aurally and visually presented Japanese words wer measured for 11 subjects, in order to investigate the modality dependency of familiarity. The correlation coefficient between auditory and visual ratings was .808, which is lower than that observed for English words, suggesting that a substantial portion of the mental lexicon is modality dependent. It was shown that the modality dependency is greater for low-familiarity words than it is for medium- or high-familiarity words. This difference between the low- and the medium- or high-familiarity words has a relationship to orthography. That is, the dependency is larger in words consisting only of kanji, which may have multiple pronunciations and usually represent meaning, than it is in words consisting only of hiragana or katakana, which have a single pronunciation and usually do not represent meaning. These results indicate that the idiosyncratic characteristics of Japanese orthography contribute to the modality dependency.

  2. Cross-modal illusory conjunctions between vision and touch.

    Science.gov (United States)

    Cinel, Caterina; Humphreys, Glyn W; Poli, Riccardo

    2002-10-01

    Cross-modal illusory conjunctions (ICs) happen when, under conditions of divided attention, felt textures are reported as being seen or vice versa. Experiments provided evidence for these errors, demonstrated that ICs are more frequent if tactile and visual stimuli are in the same hemispace, and showed that ICs still occur under forced-choice conditions but do not occur when attention to the felt texture is increased. Cross-modal ICs were also found in a patient with parietal damage even with relatively long presentations of visual stimuli. The data are consistent with there being cross-modal integration of sensory information, with the modality of origin sometimes being misattributed when attention is constrained. The empirical conclusions from the experiments are supported by formal models.

  3. Sistemas multi–modales de profundidad restringida Multi-modal systems of restricted depth

    Directory of Open Access Journals (Sweden)

    Manuel Sierra A.

    2008-12-01

    Full Text Available Se presentan como extensiones del cálculo proposicional clásico, la jerarquíade sistemas deductivos SMM–n con n > 1. SMM–n es el sistema multi–modalde profundidad–n. El sistema SMM–1 es el cálculo proposicional clásico. Elsistema SMM–(n + 1 puede ser visto como el resultado de aplicar la regla denecesariedad, asociada a los razonadores con suficiente capacidad de razona-miento, una vez a los teoremas del sistema SMM–n. El sistema SMM resultade la reunión de los sistemas de la jerarquía, y puede ser visto como el sis-tema de lógica multi–modal Km con restricciones. Los sistemas SMM–n soncaracterizados con una semántica al estilo Kripke, en la cual, la longitud delas cadenas de mundos posibles se encuentra restringida.They are presented as extensions of the classical propositional logic, the hierarchy of deductive systems SMM–n with n > 1. SMM–n is the multi–modal system of depth–n. The system SMM–1 is the classical propositional logic. The system SMM–(n + 1 it can be seen as the result of applying the necesariedad rule, associated to the reasoners with enough reasoning capacity, once to the theorems of the system SMM–n. The system SMM is of the union of the systems of the hierarchy, and it can be seen as the system of logic multimodal Km with restrictions. The systems SMM–n are characterized with a semantics to the style Kripke, in the one which, the longitude of the chains of possible worlds is restricted.

  4. Non linear structures seismic analysis by modal synthesis

    International Nuclear Information System (INIS)

    Aita, S.; Brochard, D.; Guilbaud, D.; Gibert, R.J.

    1987-01-01

    The structures submitted to a seismic excitation, may present a great amplitude response which induces a non linear behaviour. These non linearities have an important influence on the response of the structure. Even in this case (local shocks) the modal synthesis method remains attractive. In this paper we will present the way of taking into account, a local non linearity (shock between structures) in the seismic response of structures, by using the modal synthesis method [fr

  5. Mobile Education: Towards Affective Bi-modal Interaction for Adaptivity

    Directory of Open Access Journals (Sweden)

    Efthymios Alepis

    2009-04-01

    Full Text Available One important field where mobile technology can make significant contributions is education. However one criticism in mobile education is that students receive impersonal teaching. Affective computing may give a solution to this problem. In this paper we describe an affective bi-modal educational system for mobile devices. In our research we describe a novel approach of combining information from two modalities namely the keyboard and the microphone through a multi-criteria decision making theory.

  6. Dual-Modality Prostate Imaging with PET and Transrectal Ultrasound

    Science.gov (United States)

    2011-09-01

    Downloaded on April 07,2010 at 23:12:26 UTC from IEEE Xplore . Restrictions apply. HUBER et al.: MULTI-MODALITY PHANTOM DEVELOPMENT 2723 As soon as...allow Authorized licensed use limited to: Lawrence Berkeley National Laboratory. Downloaded on April 07,2010 at 23:12:26 UTC from IEEE Xplore ...April 07,2010 at 23:12:26 UTC from IEEE Xplore . Restrictions apply. HUBER et al.: MULTI-MODALITY PHANTOM DEVELOPMENT 2725 Fig. 3. Reconstructed

  7. Optimization of modal filters based on arrays of piezoelectric sensors

    International Nuclear Information System (INIS)

    Pagani, Carlos C Jr; Trindade, Marcelo A

    2009-01-01

    Modal filters may be obtained by a properly designed weighted sum of the output signals of an array of sensors distributed on the host structure. Although several research groups have been interested in techniques for designing and implementing modal filters based on a given array of sensors, the effect of the array topology on the effectiveness of the modal filter has received much less attention. In particular, it is known that some parameters, such as size, shape and location of a sensor, are very important in determining the observability of a vibration mode. Hence, this paper presents a methodology for the topological optimization of an array of sensors in order to maximize the effectiveness of a set of selected modal filters. This is done using a genetic algorithm optimization technique for the selection of 12 piezoceramic sensors from an array of 36 piezoceramic sensors regularly distributed on an aluminum plate, which maximize the filtering performance, over a given frequency range, of a set of modal filters, each one aiming to isolate one of the first vibration modes. The vectors of the weighting coefficients for each modal filter are evaluated using QR decomposition of the complex frequency response function matrix. Results show that the array topology is not very important for lower frequencies but it greatly affects the filter effectiveness for higher frequencies. Therefore, it is possible to improve the effectiveness and frequency range of a set of modal filters by optimizing the topology of an array of sensors. Indeed, using 12 properly located piezoceramic sensors bonded on an aluminum plate it is shown that the frequency range of a set of modal filters may be enlarged by 25–50%

  8. Multi-Modality Registration And Fusion Of Medical Image Data

    International Nuclear Information System (INIS)

    Kassak, P.; Vencko, D.; Cerovsky, I.

    2008-01-01

    Digitalisation of health care providing facilities allows US to maximize the usage of digital data from one patient obtained by various modalities. Complex view on to the problem can be achieved from the site of morphology as well as functionality. Multi-modal registration and fusion of medical image data is one of the examples that provides improved insight and allows more precise approach and treatment. (author)

  9. Modal data for the BARC challenge problem Test Report

    Energy Technology Data Exchange (ETDEWEB)

    Rohe, Daniel Peter [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2018-01-22

    Modal testing was performed on the uncut BARC structure as a whole and broken into its two sub-assemblies. The structure was placed on soft foam during the test. Excitation was provided with a small modal hammer attached to an actuator. Responses were measured using a 3D Scanning Laser Doppler Vibrometer. Data, shapes, and geometry from this test can be downloaded in Universal File Format from the Sandia Connect SharePoint site.

  10. Distributed Graphs for Solving Co-modal Transport Problems

    OpenAIRE

    Karama , Jeribi; Hinda , Mejri; Hayfa , Zgaya; Slim , Hammadi

    2011-01-01

    International audience; The paper presents a new approach based on a special distributed graphs in order to solve co-modal transport problems. The co-modal transport system consists on combining different transport modes effectively in terms of economic, environmental, service and financial efficiency, etc. However, the problem is that these systems must deal with different distributed information sources stored in different locations and provided by different public and private companies. In...

  11. Importance of modal cross-correlations on wind loaded structures

    OpenAIRE

    Denoël, Vincent; Degée, Hervé; De Ville De Goyet, Vincent

    2006-01-01

    In civil engineering applications the dynamic analysis of large structure is often performed in a modal space. This method is known to offer an interesting decrease of the number of degrees of freedom as well as a decomposition of the structure’s response in “uncoupled” components. Even if the response in each mode can be computed independently from the responses in the other ones, in the context of stochastic loading, the coherence of these modal responses must be accounted fo...

  12. On Some Syntactic Properties of the Modalized Heyting Calculus

    OpenAIRE

    Muravitsky, Alexei

    2016-01-01

    We show that the modalized Heyting calculus introduced by Leo Esakia admits a normal axiomatization. Then, we prove that the inference rules $\\square\\alpha/\\alpha$ and $\\square\\alpha\\rightarrow\\alpha/\\alpha$ are admissible in this calculus. Finally, we show that this calculus and intuitionistic propositional calculus are assertorically equipollent, which leads to a variant of limited separation property for the modalized Heyting calculus.

  13. Dynamic Modal Analysis of Vertical Machining Centre Components

    OpenAIRE

    Anayet U. Patwari; Waleed F. Faris; A. K. M. Nurul Amin; S. K. Loh

    2009-01-01

    The paper presents a systematic procedure and details of the use of experimental and analytical modal analysis technique for structural dynamic evaluation processes of a vertical machining centre. The main results deal with assessment of the mode shape of the different components of the vertical machining centre. The simplified experimental modal analysis of different components of milling machine was carried out. This model of the different machine tool's structure is made by design software...

  14. Updating Stiffness and Hysteretic Damping Matrices Using Measured Modal Data

    Directory of Open Access Journals (Sweden)

    Jiashang Jiang

    2018-01-01

    Full Text Available A new direct method for the finite element (FE matrix updating problem in a hysteretic (or material damping model based on measured incomplete vibration modal data is presented. With this method, the optimally approximated stiffness and hysteretic damping matrices can be easily constructed. The physical connectivity of the original model is preserved and the measured modal data are embedded in the updated model. The numerical results show that the proposed method works well.

  15. Updating Stiffness and Hysteretic Damping Matrices Using Measured Modal Data

    OpenAIRE

    Jiashang Jiang; Yongxin Yuan

    2018-01-01

    A new direct method for the finite element (FE) matrix updating problem in a hysteretic (or material) damping model based on measured incomplete vibration modal data is presented. With this method, the optimally approximated stiffness and hysteretic damping matrices can be easily constructed. The physical connectivity of the original model is preserved and the measured modal data are embedded in the updated model. The numerical results show that the proposed method works well.

  16. Many-dimensional modal logics theory and applications

    CERN Document Server

    Gabbay, D M; Wolter, F; Zakharyaschev, M

    2003-01-01

    Modal logics, originally conceived in philosophy, have recently found many applications in computer science, artificial intelligence, the foundations of mathematics, linguistics and other disciplines. Celebrated for their good computational behaviour, modal logics are used as effective formalisms for talking about time, space, knowledge, beliefs, actions, obligations, provability, etc. However, the nice computational properties can drastically change if we combine some of these formalisms into a many-dimensional system, say, to reason about knowledge bases developing in time or moving objects.

  17. Hyperpolarized 129Xe MRI: A viable functional lung imaging modality?

    International Nuclear Information System (INIS)

    Patz, Samuel; Hersman, F. William; Muradian, Iga; Hrovat, Mirko I.; Ruset, Iulian C.; Ketel, Stephen; Jacobson, Francine; Topulos, George P.; Hatabu, Hiroto; Butler, James P.

    2007-01-01

    The majority of researchers investigating hyperpolarized gas MRI as a candidate functional lung imaging modality have used 3 He as their imaging agent of choice rather than 129 Xe. This preference has been predominantly due to, 3 He providing stronger signals due to higher levels of polarization and higher gyromagnetic ratio, as well as its being easily available to more researchers due to availability of polarizers (USA) or ease of gas transport (Europe). Most researchers agree, however, that hyperpolarized 129 Xe will ultimately emerge as the imaging agent of choice due to its unlimited supply in nature and its falling cost. Our recent polarizer technology delivers vast improvements in hyperpolarized 129 Xe output. Using this polarizer, we have demonstrated the unique property of xenon to measure alveolar surface area noninvasively. In this article, we describe our human protocols and their safety, and our results for the measurement of the partial pressure of pulmonary oxygen (pO 2 ) by observation of 129 Xe signal decay. We note that the measurement of pO 2 by observation of 129 Xe signal decay is more complex than that for 3 He because of an additional signal loss mechanism due to interphase diffusion of 129 Xe from alveolar gas spaces to septal tissue. This results in measurements of an equivalent pO 2 that accounts for both traditional T 1 decay from pO 2 and that from interphase diffusion. We also provide an update on new technological advancements that form the foundation for an improved compact design polarizer as well as improvements that provide another order-of-magnitude scale-up in xenon polarizer output

  18. Modality-Specific Axonal Regeneration: Towards selective regenerative neural interfaces

    Directory of Open Access Journals (Sweden)

    Parisa eLotfi

    2011-10-01

    Full Text Available Regenerative peripheral nerve interfaces have been proposed as viable alternatives for the natural control of robotic prosthetic devices. However, sensory and motor axons at the neural interface are of mixed submodality types, which difficult the specific recording from motor axons and the eliciting of precise sensory modalities through selective stimulation. Here we evaluated the possibility of using type-specific neurotrophins to preferentially entice the regeneration of defined axonal populations from transected peripheral nerves into separate compartments. Segregation of mixed sensory fibers from dorsal root ganglion neurons was evaluated in vitro by compartmentalized diffusion delivery of nerve growth factor (NGF and neurotrophin-3 (NT-3, to preferentially entice the growth of TrkA+ nociceptive and TrkC+ proprioceptive subsets of sensory neurons, respectively. The average axon length in the NGF channel increased 2.5 fold compared to that in saline or NT-3, whereas the number of branches increased 3 fold in the NT-3 channels. These results were confirmed using a 3-D Y-shaped in vitro assay showing that the arm containing NGF was able to entice a 5-fold increase in axonal length of unbranched fibers. To address if such segregation can be enticed in vivo, a Y-shaped tubing was used to allow regeneration of the transected adult rat sciatic nerve into separate compartments filled with either NFG or NT-3. A significant increase in the number of CGRP+ pain fibers were attracted towards the sural nerve, while N-52+ large diameter axons were observed in the tibial and NT-3 compartments. This study demonstrates the guided enrichment of sensory axons in specific regenerative chambers, and supports the notion that neurotrophic factors can be used to segregate sensory and perhaps motor axons in separate peripheral interfaces.

  19. Therapeutic modalities to combat leishmaniasis, a review

    Directory of Open Access Journals (Sweden)

    Hamid Iqbal

    2016-01-01

    Full Text Available Leishmaniasis is an emerging dermal disorder that causes high morbidity and mortality levels with a wide spectrum of clinical complications. Current situation of chemotherapeutic options with some attempts at immunotherapy has remained a dilemma for the treatment of leishmaniasis. Primary precautionary measure which relies on the managed control of the host and sandfly bite prevention is difficult to establish, as the transmission of the disease is manifested by various Leishmania species. Secondary and tertiary prevention is dependent on the medical assistance using clinical guidelines and adequate therapy. However, long course of duration and resistant nature of drugs with pronounced side effects often lead to reduction or cessation of treatment. The aim of this article is to view the current status of chemotherapeutic agents used against leishmaniasis; a review of natural plant extracts exhibiting antileishmanial activities in vitro or in vivo alone or in combination with recommended drugs seeming to validate their use in folk medicine, topical applications of ointments currently used to develop new compounds under trial, substantial efforts in vaccine development and insights about immunoregulation along with the recommendations and guidelines for future perspectives.

  20. Spiral CT and optimization of the modalities of the iodinated intravenous contrast material: Experimental studies in human pathology

    International Nuclear Information System (INIS)

    Bonaldi, V.

    1998-01-01

    Spiral (or helical) CT represents the most recent improvement in the field of computed assisted tomography (CAT scan). The capabilities of this new imaging modality are much superior to these of conventional CT scanning; then result from the rapid acquisition and from the volumetric nature of the derived data set. The short time of data acquisition had made mandatory the revision of protocols for intravenous administration of iodinated contrast material. By the means of several studies, carried out on pathologic and healthy patients, we have attempted to improve knowledge in factors influencing CT attenuation values after injection of contrast material, in the aim of improving contrast administration performed during spiral CT scanning. Anatomical landmarks that we have studied till now have been liver, the pancreas, the kidney and the cervical spine. In addition, a paired based methodology has been used. The volumetric set of data derived from spiral CT scanning leads to optimal post-processing tasks, the most interesting being related to cine-display and multiplanar reformatting; both modalities have been evaluated, about the pancreas and the musculo-skeletal system respectively. Conversely, this new modality, as for other imaging modalities, is responsible for additional costs derived from restless increase in the number of images to be dealt with and from the occurrence of new tasks (in post-processing particularly). The place of spiral CT in diagnostic strategies among other modern imaging modalities should be assessed, especially with respect to Magnetic Resonance Imaging (MRI). (author)