WorldWideScience

Sample records for naoh aqueous solutions

  1. Hydrogen production by sodium borohydride in NaOH aqueous solution

    Science.gov (United States)

    Wang, Q.; Zhang, L. F.; Zhao, Z. G.

    2018-01-01

    The kinetics of hydrolysis reaction of NaBH4 in NaOH aqueous solution is studied. The influence of pH of the NaOH aqueous solution on the rate of hydrogen production and the hydrogen production efficiency are studied for the hydrolysis reaction of NaBH4. The results show that the activation energy of hydrolysis reaction of NaBH4 increased with the increase of the initial pH of NaOH aqueous solution.With the increasing of the initial pH of NaOH aqueous solution, the rate of hydrogen production and hydrogen production efficiency of NaBH4 hydrolysis decrease.

  2. Dissolution of B-doped S1(100) layers in NaOH aqueous solutions

    International Nuclear Information System (INIS)

    Akhter, P.; Baig, A.; Mufti, A.

    1988-12-01

    NaOH solution has been used to study the dissolution rates of boron doped Sl(100) wafers as a function of solution normality (0.02 N to 15 N) and temperature in the range of 30 deg. C to boiling point. For a dissolution at boiling point, two distinctive ranges of solution normalities have been observed. For N ≤ 4.5, the dissolution rate increases logarithmically and is defect dependent. For higher values of N ≥ 4.5 normal, the dissolution rate becomes a linear function of normality and reaction is defect dependent. The reaction activation energy has been measured equal to 0.65 +- 0.03 eV. (author). 7 refs, 5 figs

  3. Characterization of Ti6Al7Nb alloy foams surface treated in aqueous NaOH and CaCl2 solutions.

    Science.gov (United States)

    Bütev, Ezgi; Esen, Ziya; Bor, Şakir

    2016-07-01

    Ti6Al7Nb alloy foams having 53-73% porosity were manufactured via evaporation of magnesium space holders. A bioactive 1µm thick sodium hydrogel titanate layer, NaxH2-xTiyO2y+1, formed after 5M NaOH treatment, was converted to crystalline sodium titanate, Na2TiyO2y+1, as a result of post-heat treatment. On the other hand, subsequent CaCl2 treatment of NaOH treated specimens induced calcium titanate formation. However, heat treatment of NaOH-CaCl2 treated specimens led to the loss of calcium and disappearance of the titanate phase. All of the aforementioned surface treatments reduced yield strengths due to the oxidation of the cell walls of the foams, while elastic moduli remained mostly unchanged. Accordingly, equiaxed dimples seen on the fracture surfaces of as-manufactured foams turned into relatively flat and featureless fracture surfaces after surface treatments. On the other hand, Ca- and Na-rich coating preserved their mechanical stabilities and did not spall during fracture. The relation between mechanical properties of foams and macro-porosity fraction were found to obey a power law. The foams with 63 and 73% porosity met the desired biocompatibility requirements with fully open pore structures and elastic moduli similar to that of bone. In vitro tests conducted in simulated body fluid (SBF) showed that NaOH-heat treated surfaces exhibit the highest bioactivity and allow the formation of Ca-P rich phases having Ca/P ratio of 1.3 to form within 5 days. Although Ca-P rich phases formed only after 15 days on NaOH-CaCl2 treated specimens, the Ca/P ratio was closer to that of apatite found in bone. Copyright © 2016 Elsevier Ltd. All rights reserved.

  4. Raman spectra from very concentrated aqueous NaOH and from wet and dry, solid, and anhydrous molten, LiOH, NaOH, and KOH.

    Science.gov (United States)

    Walrafen, George E; Douglas, Rudolph T W

    2006-03-21

    High-temperature, high-pressure Raman spectra were obtained from aqueous NaOH solutions up to 2NaOHH2O, with X(NaOH)=0.667 at 480 K. The spectra corresponding to the highest compositions, X(NaOH)> or =0.5, are dominated by H3O2-. An IR xi-function dispersion curve for aqueous NaOH, at 473 K and 1 kbar, calculated from the data of Franck and Charuel indicates that the OH- ion forms H3O2- by preferential H bonding with nonhydrogen-bonded OH groups. Raman spectra from wet to anhydrous, solid LiOH, NaOH, and KOH yield sharp, symmetric OH- stretching peaks at 3664, 3633, and 3596 cm(-1), respectively, plus water-related, i.e., H3O2-, peaks near LiOH, 3562 cm(-1), NaOH, 3596 cm(-1), and, KOH, 3500 cm(-1). Absence of H3O2- peaks from the solid assures that the corresponding melt is anhydrous. Raman spectra from the anhydrous melts yield OH- stretching peak frequencies: LiOH, 3614+/-4 cm(-1), 873 K; NaOH, 3610+/-2 cm(-1), 975 K; and, KOH, 3607+/-2 cm(-1), 773 K, but low-frequency asymmetry due to ion-pair interactions is present which is centered near 3550 cm(-1). The ion-pair-related asymmetry corresponds to the sole IR maximum near 3550 cm(-1) from anhydrous molten NaOH, at 623 K. Bose-Einstein correction of published low-frequency Raman data from molten LiOH revealed an acoustic phonon, near 205 cm(-1), related to restricted translation of OH- versus Li+, and an optical phonon, at 625 cm(-1) and tau approximately 0.05 ps, due to protonic precession and/or pendular motion. Strong H bonding between water and the O atom of OH- forms H3O2-, but the proton of OH- does not bond with H significantly. Large Raman bandwidths (aqueous solutions) are explained in terms of inhomogeneous broadening due to proton transfer in a double well. Vibrational assignments are presented for H3O2-.

  5. Solubility of flue gas components in NaOH based scrubber solutions

    Energy Technology Data Exchange (ETDEWEB)

    Sandelin, K; Backman, R

    1997-11-01

    The work reported here is a thermodynamic study on the solubility of flue gas components in aqueous solutions containing sodium salts. The result of the work is an equilibrium model. The model presented here includes sodium hydroxide and sodium salts that makes it possible to study simultaneous absorption of flue gas components in alkaline scrubber solutions. The model is applied on the absorption of a flue gas into a NaOH scrubber solution. The calculations show that it is possible to simultaneously absorb sulfur dioxide, sulfuric acid, and ammonia without carbon dioxide co-absorption. The calculations also show that gaseous NO and N{sub 2}O cannot be scrubbed unless they are oxidized to nitrate or reduced to ammonia. (author) SIHTI 2 Research Programme. 59 refs.

  6. Cation incorporation into zirconium oxide in LiOH, NaOH, and KOH solutions

    International Nuclear Information System (INIS)

    Jeong, Y.H.; Kim, K.H.; Baek, J.H.

    1999-01-01

    To investigate the cation incorporation into zirconium oxide, SIMS analysis was performed on the specimens prepared to have an equal oxide thickness in LiOH, NaOH, and KOH solutions. Even though they have an equal oxide thickness in LiOH, NaOH, and KOH solutions, the penetration depth of cation into the oxide decreased with an increase in the ionic radius of cation. The cation is considered to control the corrosion in alkali hydroxide solutions and its effect is dependent on the concentration of alkali and the oxide thickness. The slight enhancement of the corrosion rate at a low concentration is thought to be caused by cation incorporation into oxide, while the significant acceleration at a high concentration is due to the transformation of oxide microstructures that would be also induced by cation incorporation into oxide. (orig.)

  7. Effect of grain size on corrosion of nanocrystalline copper in NaOH solution

    International Nuclear Information System (INIS)

    Luo Wei; Xu Yimin; Wang Qiming; Shi Peizhen; Yan Mi

    2010-01-01

    Research highlights: → Coppers display an active-passive-transpassive behaviour with duplex passive film. → Grain size variation has little effect on the overall corrosion behaviour of Cu. → Little effect on corrosion may be due to duplex passivation in NaOH solution. → Bulk nanocrystalline Cu show bamboo-like flake corrosion structure. - Abstract: Effect of grain size on corrosion of bulk nanocrystalline copper was investigated using potentiodynamic polarization measurements in 0.1 M NaOH solution. Bulk nanocrystalline copper was prepared by inert gas condensation and in situ warm compress (IGCWC) method. The grain sizes of all bulk nanocrystalline samples were determined to be 48, 68 and 92 nm using X-ray diffraction (XRD). Results showed that bulk coppers displayed an active-passive-transpassive behaviour with duplex passive films. From polycrystalline to nanocrystalline, grain size variation showed little effect on the overall corrosion resistance of copper samples.

  8. Aqueous polyethylene oxide solutions

    International Nuclear Information System (INIS)

    Breen, J.

    1987-01-01

    A number of aspects concerning the reorientation of polymer, water and ion hydration complexes have been studied in aqueous solution of polyethylene oxide (PEO). The polymer dynamics are investigated by 1 H-PEO and 13 C-PEO nuclear relaxation experiments. 162 refs.; 30 figs.; 19 tabs

  9. 40 CFR 796.1050 - Absorption in aqueous solution: Ultraviolet/visible spectra.

    Science.gov (United States)

    2010-07-01

    ... applied to measure the absorption spectra. (b) Method—(1)(i) Introduction, purpose, scope, relevance... volume of HCl or NaOH in aqueous solution ([HCl], [NaOH]=1 mol/L). (4) In theory, all chemical species...) Katelaar, J.A.A., Photoelectric Spectrometry Group Bulletin, 8, (Cambridge, 1955). (3) Chemical Rubber...

  10. Semiconducting properties of oxide films formed onto an Nb electrode in NaOH solutions

    Directory of Open Access Journals (Sweden)

    VLADIMIR D. JOVIC

    2008-03-01

    Full Text Available In this paper, the results of the potentiostatic formation of homogeneous and heterogeneous, nano-crystalline passive films of Nb2O5 onto an Nb electrode in NaOH solutions of different concentrations at potentials lower than 3.0 V vs. SCE are presented. The semiconducting properties of such films were investigated by EIS measurements. After fitting the EIS results by appropriate equivalent circuits, the space charge capacitance (Csc and space charge resistance (Rsc of these films were determined. The donor density (Nsc, flat band potential (Efb and thickness of the space charge layer (dsc for such oxide films were determined from the corresponding Mott–Schottky (M–S plots. It is shown that all oxide films were n-type semiconductors in a certain potential range.

  11. The effects of H2SO4 and NaOH solutions on irradiated sawdust for ethanol production

    International Nuclear Information System (INIS)

    Lina, M.R.; Susiana; Siagian, E.G.

    1988-01-01

    The research of gamma irradiated sawdust, which were added H2SO4 and NaOH solutions on fermentation process for ethanol production was investigated. Irradiation doses used were : 0 and 200 kGy, while H2SO4 and NaOH solutions had concentrations of 0,1 and 2% (v/v) and (b/v), with a ratio of sawdust weight and solution volume = 1:3. Fine powder of sawdust with a mesh of 60, was hydrolysed by enzyme (cellulase), S.cerevisiae was a yeast used for fermentation process and fermentation time was 4 hours. From the experimental results showed that irradiation doses up to 200 kGy, could increase the ethanol concentration from sawdust fermentation signivicantly (P= . Irradiation treatment, addition of the solutions and its interaction could not influence the total carbohydrate before and after fermentation. (author). 9 refs, 2 figs, 6 tabs

  12. A quick method for maintaining the molarity of NaOH solution during continuous etching of CR-39

    International Nuclear Information System (INIS)

    Khan, E.U.; Husaini, S.N.; Malik, F.; Sajid, M.; Karim, S.; Qureshi, I.E.

    2002-01-01

    A series of experiments have been performed to investigate the physio-chemical changes that occurred in the 6 M NaOH solution after etching CR-39 (Pershore and Homalite) detectors, each for 3, 6, 9, 12 and 15 h. Various physical parameters like concentration, electrical conductivity (EC) and density of the solutions have been measured after each etching interval. Results have been discussed in the light of stoichiometrical equation for the interaction of CR-39 with NaOH. It is found that the concentration, EC and the density of the solution, in which CR-39 has been etched, increase linearly with respect to the etching time. The inter-relationship of EC-concentration and density-concentration suggest that the concentration of the etchant can be maintained at certain desired value by adjusting the corresponding value of EC or density, measured through non-destructive and quick methods

  13. 2010 Water & Aqueous Solutions

    Energy Technology Data Exchange (ETDEWEB)

    Dor Ben-Amotz

    2010-08-13

    Water covers more than two thirds of the surface of the Earth and about the same fraction of water forms the total mass of a human body. Since the early days of our civilization water has also been in the focus of technological developments, starting from converting it to wine to more modern achievements. The meeting will focus on recent advances in experimental, theoretical, and computational understanding of the behavior of the most important and fascinating liquid in a variety of situations and applications. The emphasis will be less on water properties per se than on water as a medium in which fundamental dynamic and reactive processes take place. In the following sessions, speakers will discuss the latest breakthroughs in unraveling these processes at the molecular level: Water in Solutions; Water in Motion I and II; Water in Biology I and II; Water in the Environment I and II; Water in Confined Geometries and Water in Discussion (keynote lecture and poster winners presentations).

  14. Promotion of hydrogen entry into iron from NaOH solution by iron-oxygen species

    International Nuclear Information System (INIS)

    Flis-Kabulska, I.; Flis, J.; Zakroczymski, T.

    2007-01-01

    This study was carried out to explain reasons of the enhanced hydrogen entry into iron at low polarisations. Hydrogen permeation rate (HPR) through a 35-μm thick iron membrane was studied with the electrochemical technique in 0.1 M NaOH at 25 o C. A rotating split-ring disk electrode was used to detect soluble Fe(II) species. Enhanced hydrogen entry (HPR peaks) was observed at low cathodic and low anodic polarisations during voltammetric cycling, and also during galvanostatic anodic polarisation applied after cathodic charging. HPR peaks occurred at potentials from about -1.2 to -0.9 V (NHE) which were more cathodic than the potentials of thermodynamic stability of Fe(OH) 2 or Fe 3 O 4 , and of the formation of soluble Fe(II) species. It has been suggested that the enhanced hydrogen entry is associated with the presence of FeOH ad . In this species oxygen is bound with hydrogen (oxo-hydride), hence it can be supposed that the mechanism of its promoting effect can be similar to that of hydrides of other elements of the VIb group

  15. Electrochemical impedance spectroscopy investigation on indium tin oxide films under cathodic polarization in NaOH solution

    International Nuclear Information System (INIS)

    Gao, Wenjiao; Cao, Si; Yang, Yanze; Wang, Hao; Li, Jin; Jiang, Yiming

    2012-01-01

    The electrochemical corrosion behaviors of indium tin oxide (ITO) films under the cathodic polarization in 0.1 M NaOH solution were investigated by electrochemical impedance spectroscopy. The as-received and the cathodically polarized ITO films were characterized by scanning electron microscopy, energy dispersive X-ray spectroscopy and X-ray diffraction for morphological, compositional and structural studies. The results showed that ITO films underwent a corrosion process during the cathodic polarization and the main component of the corrosion products was body-centered cubic indium. The electrochemical impedance parameters were related to the effect of the cathodic polarization on the ITO specimens. The capacitance of ITO specimens increased, while the charge transfer resistance and the inductance decreased with the increase of the polarization time. The proposed mechanism indicated that the corrosion products (metallic indium) were firstly formed during the cathodic polarization and then absorbed on the surface of the ITO film. As the surface was gradually covered by indium particles, the corrosion process was suppressed. - Highlights: ► Cathodic polarization of indium tin oxide (ITO) in 0.1 M NaOH. ► Cathodic polarization studied with electrochemical impedance spectroscopy. ► ITO underwent a corrosion attack during cathodic polarization, indium was observed. ► Electrochemical parameters of ITO were obtained using equivalent electrical circuit. ► A corrosion mechanism is proposed.

  16. Simultaneous absorption of SO2 and NO from flue gas with KMnO4/NaOH solutions

    International Nuclear Information System (INIS)

    Chu, H.; Chien, T.W.; Li, S.Y.

    2001-01-01

    The wet scrubbing combined SO x /NO x removal system is an advanced air pollution control device. This study attempts to understand the absorption kinetics in the system. The absorption of diluted SO 2 and simultaneous absorption of diluted SO 2 and NO, as occurs in flue gases, in a stirred tank reactor with KMnO 4 /NaOH solutions were carried out at 50C. The liquid-side and gas-side mass transfer coefficients of the system were determined. The results indicate that the absorption of SO 2 is close to completely gas-film controlled where the NaOH concentration is greater than 0.1 M or the KMnO 4 concentration is greater than 0.05 M. The increasing gas flow rate has a positive effect on the absorption rate of SO 2 . The existence of O 2 has no significant effect on the absorption rate of SO 2 . Adding SO 2 would decrease the absorption rate of NO; however, the addition of NO has no effect on the absorption rate of SO 2

  17. Lanthanide complexation in aqueous solutions

    International Nuclear Information System (INIS)

    Choppin, G.R.

    1984-01-01

    The lanthanide elements form an extended series of cations with the same charge, slightly varying radii and useful magnetic and spectroscopic properties. Their use in technology is growing rapidly as their properties are more fully explored. The lanthanides also offer scientists valuable and often unique probes for investigating a variety of chemical and physical phenomena. This review has attempted to call attention to these latter uses without trying to provide a thorough discussion of all the relevant literature. Hopefully, awareness of the more interesting facets of present studies of lanthanide complexes in aqueous solution will spur even more advances in the use of these elements. (Auth.)

  18. Radiolysis of Aqueous Toluene Solutions

    Energy Technology Data Exchange (ETDEWEB)

    Christensen, H C; Gustafson, R

    1971-04-15

    Aqueous toluene solutions have been irradiated with Co gamma-rays. In unbuffered solutions the various cresol isomers are formed in a total yield of 0.45, 0.87 and 0.94 molecules/100 eV absorbed energy in argon-, N{sub 2}O- and air - saturated solutions, respectively. The yields are reduced in acid (pH 3) solutions (G = 0.14, 0.14 and 0.52, respectively) but the reduction is compensated by the formation of 1,2-di-phenylethane in yields of 0.49 and 1.60 in argon- and N{sub 2}O-saturated solutions, respectively. Benzyl radicals are formed through an acid catalysed water elimination reaction from the initially formed hydroxymethylcyclohexadienyl radical. Phenyltolylmethanes, dimethylbiphenyls and partly reduced dimers are also formed during the radiolysis. Hydrogen is formed in the same yield as the molecular yield, g(H{sub 2}). Xylene isomers and benzene are formed in trace quantities. The most remarkable effects of the addition of Fe(III) ions to deaerated acid toluene solutions are the formation of benzyl alcohol and benzaldehyde and an increase in the yield of 1,2-diphenylethane

  19. Radiolysis of Aqueous Toluene Solutions

    International Nuclear Information System (INIS)

    Christensen, H.C.; Gustafson, R.

    1971-04-01

    Aqueous toluene solutions have been irradiated with Co γ-rays. In unbuffered solutions the various cresol isomers are formed in a total yield of 0.45, 0.87 and 0.94 molecules/100 eV absorbed energy in argon-, N 2 O- and air - saturated solutions, respectively. The yields are reduced in acid (pH 3) solutions (G 0.14, 0.14 and 0.52, respectively) but the reduction is compensated by the formation of 1,2-di-phenylethane in yields of 0.49 and 1.60 in argon- and N 2 O-saturated solutions, respectively. Benzyl radicals are formed through an acid catalysed water elimination reaction from the initially formed hydroxymethylcyclohexadienyl radical. Phenyltolylmethanes, dimethylbiphenyls and partly reduced dimers are also formed during the radiolysis. Hydrogen is formed in the same yield as the molecular yield, g(H 2 ). Xylene isomers and benzene are formed in trace quantities. The most remarkable effects of the addition of Fe(III) ions to deaerated acid toluene solutions are the formation of benzyl alcohol and benzaldehyde and an increase in the yield of 1,2-diphenylethane

  20. Synthesis of C60(OH)18-20 in aqueous alkaline solution under O2-atmosphere

    International Nuclear Information System (INIS)

    Alves, Gustavo Catao; Ladeira, Luiz Orlando; Righi, Ariete; Krambrock, Klaus; Pinheiro, Mauricio Veloso B.; Calado, Hallen Daniel; Gil, Rossimiriam Pereira de Freitas

    2006-01-01

    In this work we report on an alternative synthesis of water-soluble fullerenes known as fullerols, aiming for biomedical applications. The synthesis is based on a process in which polyethylene glycol (PEG400) is used as phase-transfer catalyst between fullerene/benzene and aqueous NaOH solutions. The polyhydroxylation of the fullerenes occurs in the NaOH solution under a continuous flow of O 2 to enhance the reaction yield. The resulting compound was characterized with infrared spectroscopy, nuclear magnetic resonance, thermo-gravimetric analysis and optical absorption. The formation of C 60 (OH) 18-20 in high yields was confirmed. (author)

  1. Solidification of radioactive aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Aikawa, Hideaki; Kato, Kiyoshi; Wadachi, Yoshiki

    1970-09-07

    A process for solidifying a radioactive waste solution is provided, using as a solidifying agent a mixture of calcined gypsum and burnt vermiculite. The quantity ratio of the mixture is preferred to be 1:1 by volume. The quantity of impregnation is 1/2 of the volume of the total quantity of the solidifying agent. In embodiments, 10 liters of plutonium waste solution was mixed with a mixture of 1:1 calcined gypsum and burnt vermiculite contained in a 20-liter cylindrical steel container lined with asphalt. The plutonium waste solution from the laboratory was neutralized with a caustic soda aqueous solution to prevent explosion due to the nitration of organic compounds. The neutralization is not always necessary. A market available dental gypsum was calcined at 400 to 500/sup 0/C and a vermiculite from Illinois was burnt at 1,100/sup 0/C to prepare the agents. The time required for the impregnation with 10 liters of plutonium solution was four minutes. After impregnation, the temperature rose to 40/sup 0/C within 30 minutes to one hour. Next, it was cooled to room temperature by standing for 3-4 hours. Solidification time was about 1 hour. The Japan Atomic Energy Research Insitute had treated and disposed about 1,000 tons of plutonium waste by this process as of August 19, 1970.

  2. Improved diffusivity of NaOH solution in autohydrolyzed poplar sapwood chips for chemi-mechanical pulp production.

    Science.gov (United States)

    Zhang, Honglei; Hou, Qingxi; Liu, Wei; Yue, Zhen; Jiang, Xiaoya; Ma, Xixi

    2018-07-01

    This work investigated the changes in the physical structure of autohydrolyzed poplar sapwood chips and the effect on the subsequent alkali liquor diffusion properties for chemi-mechanical pulping (CMP). An alkali impregnation process was conducted by using the autohydrolyzed poplar sapwood with different levels of autohydrolysis intensity. The results showed that the volume porosity, water constraint capacity, and saturated water absorption of the autohydrolyzed poplar sapwood chips increased. Also, the effective capillary cross-sectional area (ECCSA) in the radial direction and the diffusion coefficients of NaOH solution in both the radial and axial directions all increased. Autohydrolysis pretreatment enhanced the alkali liquor diffusion properties in poplar sapwood chips, and the diffusion coefficient was increased more greatly in the radial direction than that in the axial direction. Copyright © 2018 Elsevier Ltd. All rights reserved.

  3. Radiolysis of Aqueous Benzene Solutions

    Energy Technology Data Exchange (ETDEWEB)

    Christensen, H

    1964-05-15

    Aerated and deaerated aqueous solutions of benzene have been irradiated with {sup 60}Co {gamma}-rays. The products of radiolysis in deaerated, unbuffered or acid, solutions were phenol, biphenyl, hydrogen and in acid solutions also hydrogen peroxide with the following yields: G(phenol) = 0. 37 (0. 37), G(biphenyl) = 1.3 (1.7), G(H{sub 2}) = 0.44 (0. 43) and G(H{sub 2}O{sub 2}) = 0 (0.60), the figures in brackets giving the results for acid solutions. The results are shown to agree with the conclusion that k(e{sup -}{sub aq} + H{sub 2}O{sub 2}) >> k(H + H{sub 2}O{sub 2}). Furthermore, the results indicate that a competition takes place between the reactions: 2 C{sub 6}H{sub 6}OH {center_dot} -> dimer -> biphenyl. C{sub 6}H{sub 7} {center_dot} + C{sub 6}H{sub 6}OH {center_dot} -> dimer -> biphenyl. The yields in aerated, unbuffered or acid, solutions were: G(phenol) = 2.1 (2.3), G(biphenyl) = 0 (0), and G(H{sub 2}O{sub 2}) = 2.2 (3.1), the figures in brackets being valid for acid solutions. The ratio k(H + C{sub 6}H{sub 6})/k(H + O{sub 2}) was 1.4x10{sup -2}. The results indicate that peroxides, or more probably hydroperoxides, take part in the reactions. After the addition of Fe{sup 2+} or Fe{sup 3+} to aerated acid solutions G(phenol) was increased to 6.6 and 3.4 respectively. Oxygen was consumed more rapidly in the presence of Fe. Reaction mechanisms are discussed.

  4. Corrosion characteristics and oxide microstructures of Zircaloy-4 in aqueous alkali hydroxide solutions

    International Nuclear Information System (INIS)

    Jeong, Y.H.; Baek, J.H.; Kim, S.J.; Kim, H.G.

    1999-01-01

    The corrosion characteristics of Zircaloy-4 have been investigated in various aqueous solutions of LiOH, NaOH, KOH, RbOH and CsOH with equimolar M + and OH - at 350 C. The characterization of the oxides was performed using transmission electron microscope (TEM) and scanning electron microscope (SEM) on the samples which were prepared to have an equal oxide thickness in pre-transition and post-transition regimes. At a low concentration (4.3 mmol) of aqueous alkali hydroxide solutions, the corrosion rates decrease gradually as the ionic radius of cation increases. At a high concentration (32.5 mmol), the corrosion rate increases significantly in LiOH solution and slightly in NaOH solution, but in the other hydroxide solutions such as KOH, RbOH and CsOH, the corrosion rate is not accelerated. Even if the specimens have an equal oxide thickness in LiOH, NaOH and KOH solutions, the oxide microstructure formed in the LiOH solution is quite different from those formed in the NaOH or the KOH solutions. In the LiOH solution, the oxides grown in the pre-transition regime as well as in the post-transition regime have an equiaxed structure including many pores and open grain boundaries. The oxides grown in the NaOH solution have a protective columnar structure in the pre-transition regime but an equiaxed structure in the post-transition regime. On the other hand, in the KOH solution, the columnar structure is maintained from its pre-transition regime to the post-transition regime. On the basis of the above results, it can be suggested that the cation incorporation into zirconium oxide would control the oxide microstructure, the oxide growth mechanism at the metal-oxide interface and the corrosion rate in alkali hydroxide solutions. (orig.)

  5. ISOCHORIC HEAT CAPACITY OF 1% AQUEOUS SOLUTION OF MAGNESIUM CHLORIDE

    Directory of Open Access Journals (Sweden)

    V. I. Dvoryanchikov

    2016-01-01

    Full Text Available Aim. The aim is to conduct an experimental study of isochoric heat capacity of 1% aqueous solution of magnesium chloride along the phase boundary curve.Method. In order to determine the isochoric heat capacity at the phase boundary curve we used the adiabatic calorimeter of KH. I. Amirkhanov.Results. Results of the study of the isochoric heat capacity depending on the temperature are given in tables and figures; the findings are compared with those of other researchers. When evaluating a complex system, we ought not to evaluate its effectiveness on the basis of only one criterion, even a very important, in this case must take into account the requirements of the technical, economic, environmental and of other natures.Conclusions. When solving optimization problems of efficiency in geothermal energy it is necessary to take into account the fact of the temperature dependence of the heat and density. The temperature dependence of the density and heat capacity in the calculations significantly affect the value of the efficiency criterion to be taken into account, otherwise the calculation error can be up to 20%. The data obtained from the isochoric heat capacity of aqueous solutions of magnesium chloride is compared with the data for water and aqueous solutions of NaCl and NaOH, obtained previously, which may be represented as a model of geothermal and sea water.

  6. Effect of small addition of Mn on the passivation of Zn in 0.1 M NaOH solution

    International Nuclear Information System (INIS)

    Shang Xiuling; Zhang Bo; Han Enhou; Ke Wei

    2011-01-01

    The passivation of pure Zn (99.995 wt%) and Zn-0.4Mn (0.4 wt% Mn) alloy in a deaerated 0.1 M NaOH solution (pH 12.9) was investigated by electrochemical measurements, X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). The potentiodynamic polarization and electrochemical impedance measurements show that addition of 0.4 wt% Mn can decrease the passive current density of Zn in the passive region. XPS surface analysis indicates that there is approximately 1.0-2.0 at% Mn 2+ being incorporated into the passive film on Zn-0.4Mn alloy with Mn content being higher in the outer layers. Mott-Schottky analysis shows that the incorporated Mn can decrease concentration of defects in the film. AFM observations disclose that Mn can decrease the grain size of the film. The mechanism by which Mn additions improve the passivity of Zn is that the incorporated Mn can inhibit ions transportation in the film and inhibit its growth. Meanwhile, Mn can also promote the nucleation of Zn oxides and decrease film porosity.

  7. Passivation kinetics of Mg-Nd-Gd-Zn-Zr (EV31A and Mg-Y-Nd-Gd-Zr (WE43C in NaOH solutions

    Directory of Open Access Journals (Sweden)

    Jakraphan Ninlachart

    2017-09-01

    Full Text Available Passivation kinetics of two Mg-RE alloys, such as Mg-Nd-Gd-Zn-Zr (EV31A, and Mg-Y-Nd-Gd-Zr (WE43C were investigated in two different heat treated conditions (solution treated and overaged in 0.01 - 1.0 M NaOH solutions under potentiostatic conditions. Negative reaction order was observed in dilute NaOH which transitioned to positive values as the passivation time increased and in the 1 M NaOH as well. The passive layers showed platelet morphology and the size of the platelets decreased with increase in the NaOH concentration. The hydrogen evolution reaction (HER kinetics was not improved on the passive layer covered surface of the Mg-RE alloys in contrast to the improvements reported on the hydroxide covered pure magnesium. The electrochemical impedance increased with increase in the NaOH concentration in the solution treated condition of both Mg-RE alloys, whereas the overaged EV31A alloy showed a reverse trend. The passive layer of EV31A showed almost 100% higher charge carrier density than the film formed on the WE43C in the overaged condition. A better passivation behavior was observed in the solution treated condition than that in the overaged condition which could be attributed to the uniform distribution of the RE elements in the solution treated specimens. The WE43C alloy revealed better corrosion resistance in the alkaline solution than the EV31A alloy.

  8. Thermodynamic properties of potassium chloride aqueous solutions

    Science.gov (United States)

    Zezin, Denis; Driesner, Thomas

    2017-04-01

    Potassium chloride is a ubiquitous salt in natural fluids, being the second most abundant dissolved salt in many geological aqueous solutions after sodium chloride. It is a simple solute and strong electrolyte easily dissociating in water, however the thermodynamic properties of KCl aqueous solutions were never correlated with sufficient accuracy for a wide range of physicochemical conditions. In this communication we propose a set of parameters for a Pitzer-type model which allows calculation of all necessary thermodynamic properties of KCl solution, namely excess Gibbs free energy and derived activity coefficient, apparent molar enthalpy, heat capacity and volume, as well as osmotic coefficient and activity of water in solutions. The system KCl-water is one of the best studied aqueous systems containing electrolytes. Although extensive experimental data were collected for thermodynamic properties of these solutions over the years, the accurate volumetric data became available only recently, thus making possible a complete thermodynamic formulation including a pressure dependence of excess Gibbs free energy and derived properties of the KCl-water liquids. Our proposed model is intended for calculation of major thermodynamic properties of KCl aqueous solutions at temperatures ranging from freezing point of a solution to 623 K, pressures ranging from saturated water vapor up to 150 MPa, and concentrations up to the salt saturation. This parameterized model will be further implemented in geochemical software packages and can facilitate the calculation of aqueous equilibrium for reactive transport codes.

  9. EXTRACTION OF URANYL NITRATE FROM AQUEOUS SOLUTIONS

    Science.gov (United States)

    Furman, N.H.; Mundy, R.J.

    1957-12-10

    An improvement in the process is described for extracting aqueous uranyl nitrate solutions with an organic solvent such as ether. It has been found that the organic phase will extract a larger quantity of uranyl nitrate if the aqueous phase contains in addition to the uranyl nitrate, a quantity of some other soluble nitrate to act as a salting out agent. Mentioned as suitable are the nitrates of lithium, calcium, zinc, bivalent copper, and trivalent iron.

  10. Diffusion of aqueous solutions of ionic, zwitterionic, and polar solutes

    Science.gov (United States)

    Teng, Xiaojing; Huang, Qi; Dharmawardhana, Chamila Chathuranga; Ichiye, Toshiko

    2018-06-01

    The properties of aqueous solutions of ionic, zwitterionic, and polar solutes are of interest to many fields. For instance, one of the many anomalous properties of aqueous solutions is the behavior of water diffusion in different monovalent salt solutions. In addition, solutes can affect the stabilities of macromolecules such as proteins in aqueous solution. Here, the diffusivities of aqueous solutions of sodium chloride, potassium chloride, tri-methylamine oxide (TMAO), urea, and TMAO-urea are examined in molecular dynamics simulations. The decrease in the diffusivity of water with the concentration of simple ions and urea can be described by a simple model in which the water molecules hydrogen bonded to the solutes are considered to diffuse at the same rate as the solutes, while the remainder of the water molecules are considered to be bulk and diffuse at almost the same rate as pure water. On the other hand, the decrease in the diffusivity of water with the concentration of TMAO is apparently affected by a decrease in the diffusion rate of the bulk water molecules in addition to the decrease due to the water molecules hydrogen bonded to TMAO. In other words, TMAO enhances the viscosity of water, while urea barely affects it. Overall, this separation of water molecules into those that are hydrogen bonded to solute and those that are bulk can provide a useful means of understanding the short- and long-range effects of solutes on water.

  11. Diffusion coefficients of paracetamol in aqueous solutions

    International Nuclear Information System (INIS)

    Ribeiro, Ana C.F.; Barros, Marisa C.F.; Veríssimo, Luís M.P.; Santos, Cecilia I.A.V.; Cabral, Ana M.T.D.P.V.; Gaspar, Gualter D.; Esteso, Miguel A.

    2012-01-01

    Highlights: ► Mutual diffusion coefficients of paracetamol in aqueous dilute solutions. ► Influence of the thermodynamic factors on the variation of their mutual diffusion coefficients. ► Estimation of the mutual limiting diffusion coefficients of the molecular, D m 0 , and ionized forms, D ± 0 , of this drug. - Abstract: Binary mutual diffusion coefficients measured by the Taylor dispersion method, for aqueous solutions of paracetamol (PA) at concentrations from (0.001 to 0.050) mol·dm −3 at T = 298.15 K, are reported. From the Nernst–Hartley equation and our experimental results, the limiting diffusion coefficient of this drug and its thermodynamic factors are estimated, thereby contributing in this way to a better understanding of the structure of such systems and of their thermodynamic behaviour in aqueous solution at different concentrations.

  12. Aqueous Solution Chemistry of Plutonium

    Energy Technology Data Exchange (ETDEWEB)

    Clark, David L. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2014-01-28

    Things I have learned working with plutonium: Chemistry of plutonium is complex; Redox equilibria make Pu solution chemistry particularly challenging in the absence of complexing ligands; Understanding this behavior is key to successful Pu chemistry experiments; There is no suitable chemical analog for plutonium.

  13. Investigation on the Effect of Green Inhibitors for Corrosion Protection of Mild Steel in 1 M NaOH Solution

    Directory of Open Access Journals (Sweden)

    Premjith Jayakumar Ramakrishnan

    2014-01-01

    Full Text Available Alkaline corrosion is one of the main issues faced by the industries. The main chemicals abundantly used in industries are NaOH, H3PO4, HCl, and H2SO4. Corrosion control of metals has technical, economical, environmental, and aesthetical importance. The use of inhibitors is one of the best options to protect metals and alloys against corrosion. The corrosion protection of mild steel in 1 M NaOH solution by mix of Henna/Zeolite powder was studied at different temperatures by weight loss technique. Adsorption, activation, and statistical studies were addressed in this work. Adsorption studies showed that inhibitor adsorbed on metal surface according to Langmuir isotherm. Surface studies were performed by using UV-spectra and SEM. The adsorption of inhibitor on the steel surface was found to obey Langmuir’s adsorption isotherm. The inhibition efficiency increased with increasing concentration of the inhibitor in NaOH medium. Inhibition mechanism is deduced from the concentration and temperature dependence of the inhibition efficiency, Langmuir’s adsorption isotherm, SEM, and UV spectroscopic results.

  14. Molybdenum: the element and aqueous solution chemistry

    International Nuclear Information System (INIS)

    Sykes, A.G.

    1987-01-01

    This chapter on the chemistry of the coordination compounds of molybdenum concentrates on the element itself, its recovery from ores and its use in the manufacture of steels. Most of the chapter is devoted to the aqueous solution chemistry of molybdenum in oxidation states II, III and IV. (UK)

  15. Aqueous solutions/nuclear glasses interactions

    International Nuclear Information System (INIS)

    Delage, F.; Advocat, T.; Vernaz, E.; Crovisier, J.L.

    1991-01-01

    Interactions results of the borosilicate glass used in radioactive wastes confinement and aqueous solutions at various temperature and PH show that for the glass components: - the release rate evolution follows an Arrhenius law, - in acid PH, there is a selective dissolution, - in basic PH, there is a stoechiometric dissolution [fr

  16. Aqueous solutions of ionic liquids: microscopic assembly

    NARCIS (Netherlands)

    Vicent-Luna, J.M.; Dubbeldam, D.; Gómez-Álvarez, P.; Calero, S.

    2016-01-01

    Aqueous solutions of ionic liquids are of special interest, due to the distinctive properties of ionic liquids, in particular, their amphiphilic character. A better understanding of the structure-property relationships of such systems is hence desirable. One of the crucial molecular-level

  17. Pulse radiolysis of anthraquinone dye aqueous solution

    International Nuclear Information System (INIS)

    Perkowski, J.; Gebicki, J.L.; Lubis, R.; Mayer, J.

    1988-01-01

    Pulse radiolysis of argon flushed aqueous solutions of 10 -5 -10 -4 mol dm -3 anthraquinone dye (C.I. Acid Blue 62) gives rise to the transients originated from the reactions of e - aq , OH and H. The rate constants of these reactions are determined. (author)

  18. Production of Plutonium Metal from Aqueous Solutions

    Energy Technology Data Exchange (ETDEWEB)

    Orth, D.A.

    2003-01-16

    The primary separation of plutonium from irradiated uranium by the Purex solvent extraction process at the Savannah River Plant produces a dilute plutonium solution containing residual fission products and uranium. A cation exchange process is used for concentration and further decontamination of the plutonium, as the first step in the final preparation of metal. This paper discusses the production of plutonium metal from the aqueous solutions.

  19. Influence of 8-hydroxyquinoline addition on the corrosion behavior of commercial Al and Al-HO411 alloys in NaOH aqueous media

    International Nuclear Information System (INIS)

    Soliman, H.N.

    2011-01-01

    Highlights: → The corrosion of commercial Al alloy is higher than that of Al-HO411 alloy. → The inhibition efficiency increases with the increasing of 8-hydroxyquinoline (8HQ) concentration. → The inhibition efficiencies of Al-HO411 samples are higher than those of commercial Al. → The 8HQ is promising candidate to be added to the coating systems as active anti-corrosive component for corrosion protection of both alloys. - Abstract: The effect of 8-hydroxyquinoline (8HQ) on the corrosion inhibition of commercial Al and Al-HO411 alloys has been investigated in NaOH solutions. Results showed that the inhibition efficiency was increased with increasing concentration of 8HQ. Al-HO411 alloy exhibited higher corrosion resistance and inhibition efficiency than the commercial Al. Examination of both samples was studied by means of optical microscope as well as energy-dispersive X-ray spectrometer. The crystallographic structure of both samples was analyzed by means of X-ray diffractometry. It was observed that protective films are formed on the surfaces that play an essential role in the corrosion inhibition of the alloys under investigation.

  20. Silicon content design of CrSiN films for good anti-corrosion and anti-wear performances in NaOH solution

    Science.gov (United States)

    Wang, Haixin; Ye, Yuwei; Wang, Chunting; Zhang, Guangan; Liu, Wei

    2018-06-01

    The CrSiN films with different silicon contents were fabricated by medium frequency magnetron sputtering. The 304L stainless steel and Si (1 0 0) wafer were used for substrate specimens. Film plasticity, corrosion and tribological behaviors in 0.1 M NaOH solution were systematically investigated. Results show that the plasticity of CrN film could be improved by the addition of silicon. During the corrosion test, with the increase of silicon content, the corrosion current density exhibited a descending trend and impedance presented a rising trend. The COF and wear rate of as-prepared CrSiN film initially decreased and then increased as the silicon content increased. The CrSiN film with 12.7 at.% Si exhibited the lowest COF of 0.04 and a wear rate of 6.746  ×  10‑8 mm3 Nm‑1 in 0.1 M NaOH solution.

  1. Response of CR-39 to 0.9–2.5 MeV protons for KOH and NaOH etching solutions

    Energy Technology Data Exchange (ETDEWEB)

    Bahrami, F. [Department of Medical Radiation Engineering, Shiraz University, Shiraz (Iran, Islamic Republic of); Mianji, F., E-mail: fmianji@aeoi.org.ir [Nuclear Science & Technology Research Institute, Tehran (Iran, Islamic Republic of); Iran Nuclear Regulatory Authority, Tehran (Iran, Islamic Republic of); Faghihi, R. [Department of Medical Radiation Engineering, Shiraz University, Shiraz (Iran, Islamic Republic of); Taheri, M. [Iran Nuclear Regulatory Authority, Tehran (Iran, Islamic Republic of); Ansarinejad, A. [Nuclear Science & Technology Research Institute, Tehran (Iran, Islamic Republic of)

    2016-03-21

    In some circumstances passive detecting methods are the only or preferable measuring approaches. For instance, defining particles' energy profile inside the objects being irradiated with heavy ions and measuring fluence of neutrons or heavy particles in space missions are the cases covered by these methods. In this paper the ability of polyallyl diglycol carbonate (PADC) track detector (commercially known as CR-39) for passive spectrometry of proton particles is studied. Furthermore, the effect of KOH and NaOH as commonly used chemical etching solutions on the response of the detector is investigated. The experiments were carried out with protons in the energy range of 0.94–2.5 MeV generated by a Van de Graaff accelerator. Then, the exposed track dosimeters were etched in the two aforementioned etchants through similar procedure with the same normality of 6.25 N and the same temperature of 85 °C. Formation of the tracks was precisely investigated and the track diameters were recorded following every etching step for each solution using a multistage etching process. The results showed that the proposed method can be efficiently used for the spectrometry of protons over a wider dynamic range and with a reasonable accuracy. Moreover, NaOH and KOH outperformed each other over different regions of the proton energy range. The detection efficiency of both etchants was approximately 100%.

  2. Response of CR-39 to 0.9-2.5 MeV protons for KOH and NaOH etching solutions

    Science.gov (United States)

    Bahrami, F.; Mianji, F.; Faghihi, R.; Taheri, M.; Ansarinejad, A.

    2016-03-01

    In some circumstances passive detecting methods are the only or preferable measuring approaches. For instance, defining particles' energy profile inside the objects being irradiated with heavy ions and measuring fluence of neutrons or heavy particles in space missions are the cases covered by these methods. In this paper the ability of polyallyl diglycol carbonate (PADC) track detector (commercially known as CR-39) for passive spectrometry of proton particles is studied. Furthermore, the effect of KOH and NaOH as commonly used chemical etching solutions on the response of the detector is investigated. The experiments were carried out with protons in the energy range of 0.94-2.5 MeV generated by a Van de Graaff accelerator. Then, the exposed track dosimeters were etched in the two aforementioned etchants through similar procedure with the same normality of 6.25 N and the same temperature of 85 °C. Formation of the tracks was precisely investigated and the track diameters were recorded following every etching step for each solution using a multistage etching process. The results showed that the proposed method can be efficiently used for the spectrometry of protons over a wider dynamic range and with a reasonable accuracy. Moreover, NaOH and KOH outperformed each other over different regions of the proton energy range. The detection efficiency of both etchants was approximately 100%.

  3. Removal of radium from aqueous sulphate solutions

    International Nuclear Information System (INIS)

    Weir, D.R.; Masters, J.T.; Neven, M.

    1983-01-01

    Radium is often present in ores and an aqueous solution associated with the ore may consequently contain dissolved radium. It is frequently necessary to remove radium from such solutions to reduce the total radium content to a prescribed low level before the solution can be returned to the environment. The present invention is based on the discovery that the total radium content can be reduced to a satisfactory level within a reasonable time by adding a soluble barium salt to a radium-containing sulphate solution which also contains dissolved magnesium at a pH not greater than about 0 to precipitate radium as barium radium sulphate, raising the pH to at least 11 to precipitate an insoluble magnesium compound which collects the barium radium sulphate precipitate, and separating substantially all of the precipitates from the solution

  4. Uranyl fluoride luminescence in acidic aqueous solutions

    International Nuclear Information System (INIS)

    Beitz, J.V.; Williams, C.W.

    1996-01-01

    Luminescence emission spectra and decay rates are reported for uranyl species in acidic aqueous solutions containing HF or added NaF. The longest luminescence lifetime, 0.269 ± 0.006 ms, was observed from uranyl in 1 M HF + 1 M HClO 4 at 296 K and decreased with increasing temperature. Based on a luminescence dynamics model that assumes equilibrium among electronically excited uranyl fluoride species and free fluoride ion, this long lived uranyl luminescence in aqueous solution is attributed primarily to UO 2 F 2 . Studies on the effect of added LiNO 3 or Na 2 WO 4 ·2H 2 O showed relatively weak quenching of uranyl fluoride luminescence which suggests that high sensitivity determination of the UF 6 content of WF 6 gas should be feasible via uranyl luminescence analysis of hydrolyzed gas samples of impure WF 6

  5. Zeolites as alcohol adsorbents from aqueous solutions

    Directory of Open Access Journals (Sweden)

    Cekova Blagica

    2006-01-01

    Full Text Available The potential usage of zeolites as adsorbents for the removal of organic molecules from water was investigated in a series of experiments with aqueous solutions of lower alcohols. This could represent a simple solution to the problem of cleaning up industrial wastewater as well as recovering valuable chemicals at relatively low costs. Adsorption isotherms of the Langmuir type were applied, and calculations showed that the amount of propanol adsorbed on silicalite corresponded to approximately 70% of the pore volume. The adsorption process is simple, and recovery of the more concentrated products is easily done by heat treatment and/or at lowered pressures. Adsorption experiments with aqueous acetone showed that silicalite had approximately the same adsorption capacity for acetone as for n-propanol. Heats of adsorption were determined calorimetrically.

  6. Volumetric properties of itaconic acid aqueous solutions

    International Nuclear Information System (INIS)

    Nisenbaum, Alexander; Apelblat, Alexander; Manzurola, Emanuel

    2012-01-01

    Highlights: ► Densities of itaconic acid aqueous solutions in a wide range of concentrations and temperatures. ► The apparent molar volumes and the cubic expansion coefficients. ► The derivatives of isobaric heat capacities with respect to pressure. ► Changes in the structure of water when itaconic acid is dissolved. - Abstract: Densities of itaconic acid aqueous solutions were measured at 5 K intervals from T = (278.15 to 343.15) K. From the determined densities, the apparent molar volumes, the cubic expansion coefficients and the second derivatives of volume with respect to temperature which are interrelated with the derivatives of isobaric heat capacities with respect to pressure were evaluated. These derivatives were qualitatively correlated with the changes in the structure of water when itaconic acid is dissolved in it.

  7. The effectiveness of sodium hydroxide (NaOH) and sodium carbonate (Na2CO3) on the impurities removal of saturated salt solution

    Science.gov (United States)

    Pujiastuti, C.; Ngatilah, Y.; Sumada, K.; Muljani, S.

    2018-01-01

    Increasing the quality of salt can be done through various methods such as washing (hydro-extraction), re-crystallization, ion exchange methods and others. In the process of salt quality improvement by re-crystallization method where salt product diluted with water to form saturated solution and re-crystallized through heating process. The quality of the salt produced is influenced by the quality of the dissolved salt and the crystallization mechanism applied. In this research is proposed a concept that before the saturated salt solution is recrystallized added a chemical for removal of the impurities such as magnesium ion (Mg), calcium (Ca), potassium (K) and sulfate (SO4) is contained in a saturated salt solution. The chemical reagents that used are sodium hydroxide (NaOH) 2 N and sodium carbonate (Na2CO3) 2 N. This research aims to study effectiveness of sodium hydroxide and sodium carbonate on the impurities removal of magnesium (Mg), calcium (Ca), potassium (K) and sulfate (SO4). The results showed that the addition of sodium hydroxide solution can be decreased the impurity ions of magnesium (Mg) 95.2%, calcium ion (Ca) 45%, while the addition of sodium carbonate solution can decreased magnesium ion (Mg) 66.67% and calcium ion (Ca) 77.5%, but both types of materials are not degradable sulfate ions (SO4). The sodium hydroxide solution more effective to decrease magnesium ion than sodium carbonate solution, and the sodium carbonate solution more effective to decrease calcium ion than sodium hydroxide solution.

  8. Spinning of Fibers from Aqueous Solutions

    Science.gov (United States)

    2003-08-01

    recombinant silk product BioSteel . Publications, patents and presentations 1. Arcidiacono, S., et al., Purification and characterization of recombinant...ABSTRACT Previous funding supporting this research focused primarily on development of the aqueous-based method for processing silk into spin solutions. Much...of this effort consisted of production of recombinant silk protein in bacterial and yeast expression systems. In spite of the small quantities

  9. Aqueous solution dispersement of carbon nanotubes

    Science.gov (United States)

    Kim, Jae-Woo (Inventor); Park, Cheol (Inventor); Choi, Sang H. (Inventor); Lillehei, Peter T. (Inventor); Harrison, Joycelyn S. (Inventor)

    2011-01-01

    Carbon nanotubes (CNTs) are dispersed in an aqueous buffer solution consisting of at least 50 weight percent water and a remainder weight percent that includes a buffer material. The buffer material has a molecular structure defined by a first end, a second end, and a middle disposed between the first and second ends. The first end is a cyclic ring with nitrogen and oxygen heteroatomes, the middle is a hydrophobic alkyl chain, and the second end is a charged group.

  10. Photolysis of imidacloprid in aqueous solution

    International Nuclear Information System (INIS)

    Moza, P.N.; Hustert, K.; Feicht, E.; Kettrup, A.

    1998-01-01

    The photolysis of the insecticide imidacloprid in aqueous solution has been examined. Irradiation at 290 nm resulted in 90 % substrate transformation in 4 h. The degradation approximately followed first order kinetics; the rate constant is 1.6 × 10 −4 s −1 and half-life 1.2 h. 6-Chloronicotinaldehyde, N-methylnicotinacidamide, 1-(6-chloronicotinyl)imidazolidone and 6-chloro-3-pyridyl-methylethylendiamine were the main photoproducts identified by CG-MS analysis. (author)

  11. Radiolysis of anthraquinone dyes in aqueous solutions

    International Nuclear Information System (INIS)

    Vysotskaya, N.A.; Bortun, L.N.; Ogurtsov, N.A.; Migdalovich, E.A.; Revina, A.A.; Volodko, V.V.; AN SSSR, Moscow. Inst. Ehlektrokhimii)

    1986-01-01

    The commercial anthraquinone dyes (Dark Blue, Light Blue, Green) in aqueous solutions were shown to be decoloured and degrade under the action of ionizing radiation. The degree of decolouration and degradation of aromatic rings was found to increase in presence of oxygen. Hydroxyl radicals were shown to play the key role in the degradation of the dyes under irradiation. The radiolysis intermediate products were studied using the pulse radiolysis technique. (author)

  12. Pitting corrosion of zirconium in aqueous solution

    International Nuclear Information System (INIS)

    El Shayeb, H.A.; Abd El Wahab, F.M.; Abd Elk Meguid, E.A.

    1994-01-01

    The open circuit potentials of the Zr electrode are followed as a function of time in various aqueous solutions till attainment of steady state values.The results are discussed on the basis of oxide film thickening and repair. Pitting corrosion of Zr was examined in chloride solutions using the potentiodynamic technique. The effect of some inorganic and organic additives was also investigated for inhibiting the pitting corrosion of Zr and the relative performance is presented and discussed. (author). 21 refs., 6 figs., 1 tab

  13. Sound velocity in potassium hydroxide aqueous solution

    International Nuclear Information System (INIS)

    Tsapuryan, Kh.D.; Aleksandrov, A.A.; Kochetkov, A.I.

    1992-01-01

    Measurements of ultrasonic velocities in potassium hydroxide aqueous solutions are carried out within the frames of studies on improvement of water chemistry in NPP cooling systems. Method of echo pulses superposition with acoustic path length of 41.447 mm is used for measurements. The measurements are performed at 2.6 MHz frequency. Complex temperature dependence of ultrasonic velocity is determined. Ultrasonic velocity dependence on pressure is close to linear one. The formula for calculation of thermodynamic properties of the studied solutions on the basis of experimental data obtained is proposed

  14. OPTICAL PROPERTIES OF CARBAMIDE AQUEOUS SOLUTIONS

    Directory of Open Access Journals (Sweden)

    E. V. Avramenko

    2016-03-01

    Full Text Available Subject of Research. The paper presents the results of measurements of refractometric properties (refractive index n, its temperature factor dn/dt and the ultraviolet spectral absorption in carbonic acid diamide aqueous solutions (carbamide depending on solid residue mass fraction md = 0-50 % and on temperaturet = 10-70 °C.Method of Research. Laboratory methods ofliquid-phase medium refractometry and ultraviolet spectrophotometry were applied for the research. We carried out computational modeling of electronic states spectrum for the carbonic acid diamide molecule and theoretical calculation of the fundamental electronic absorption of the molecule in the ultraviolet wavelenght region.Main Results. We have established that the solution concentration md has a nonlinear character and may be represented by the quadratic polynomial with the error Δn= ± 0,0005. We have shown the refractive indexdependence on temperature n(t changes in linear fashion att = 10-70 °C.At that, the inclination of lines n(t increases at the increase of md; so, the temperature factor dn/dt may be approximated by the quadratic polynomial. Transmission spectra of solutions in the spectral region λ= 225-760 nm have no special features except for the sharp edge in the short-wavelength region; the fundamental electronic absorptionis responsible for it. We have established that dispersion dependences of the refraction index n(λ;md in aqueous solutions of carbamide at λ= 360-760 nm and at md = 0-50 % may be calculated with the satisfactory error without additional adjustable parameters from the ultraviolet absorption data in terms of the one-dimentional oscillator Lorentz model.PracticalRelevance. Representedmeasurements of carbonic acid diamide aqueous solutions optical properties may be applied for the adjustment and calibration of commercial refractometers at processing lines of the AdBlue reagent manufacture for the selective catalytic reduction (SCR of motor transport

  15. Thermodynamic properties of aqueous solutions with citrate ions. Compressibility studies in aqueous solutions of citric acid

    International Nuclear Information System (INIS)

    Apelblat, Alexander; Korin, Eli; Manzurola, Emanuel

    2013-01-01

    Highlights: • Over a wide range of concentrations and temperatures sound velocities were measured in aqueous solutions of citric acid. • Compressibility properties of citric acid solutions are thermodynamically characterized. • Changes in the structure of water when citric acid is dissolved are discussed. -- Abstract: Sound velocities in aqueous solutions of citric acid were measured from 15 °C to 50 °C in 5 °C intervals, within the 0.1 mol · kg −1 to 5.0 mol · kg −1 concentration range. These sound velocities served to evaluate the isentropic and isothermal compressibilities, the apparent molar compressibilities, the isochoric thermal pressure coefficients, changes of the cubic expansion coefficients with pressure at constant temperature, the changes of heat capacities with volume and hydration numbers of citric acid in aqueous solutions

  16. Effects of Radiosterilization on Sealed Aqueous Solutions

    International Nuclear Information System (INIS)

    Pandula, E.L.; Farkas, E.; Rácz, I.

    1967-01-01

    For aqueous solutions sensitive to heat,and in connection with the use of plastic ampoules, the need for applying radiosterilization is growing. Studying the possibilities of radiosterilization, experiments were made with the following: 0.1% atropine, 1.0% morphine, and 2% lidocain in aqueous solutions. The aim of the work was to establish whether the active ingredients of the injections suffer decomposition or not, to study the factors influencing the degradation and, furthermore, to make attempts to prevent decomposition. The samples were irradiated by 420 Ci 60 Co γ-radiation source. The applied doses were 1 to 2.5 Mrad, with a 10 4 to 2.5 x 10 5 rad/h dose intensity. After irradiation the change in colour, pH-value, concentration and UV-spectra were studied. Changes of the last three types were found. Studying the factors influencing decomposition it has been found that the degree of degradation was increased by the increase of radiation dose, increase of concentration, decrease of dose intensity, and increase of oxygen content in the atmosphere over the solution. Attempts were made to prevent degradation. Solutions were prepared with sulphite, ascorbic acid, and AET, and some measure of success was achieved, especially with the sulphite addition. (author)

  17. Inhibition of stress corrosion cracking of alloy 600 in 10% NaOH solutions with and with lead oxide at 315 C

    International Nuclear Information System (INIS)

    Hur, D.H.; Kim, J.S.; Baek, J.S.; Kim, J.G.

    2002-01-01

    Alloy 600 steam generator tube materials have experienced various degradations by corrosion such as stress corrosion cracking (SCC) on the inner and outer diameter surface of tube, intergranular attack and pitting, and by mechanical damage such as fretting-wear and fatigue. These tube degradations not only increase the costs for tube inspection, maintenance and repair but also reduce the operation safety and the efficiency of plants. Therefore, the methodologies have been extensively developed to mitigate them. The addition of inhibitors to the coolant is a feasible method to mitigate tube degradations in operating plants. In this paper, a new inhibitor is proposed to mitigate the secondary side stress corrosion cracking of alloy 600 tubes. The effect of inhibitors on the electrochemical behavior and the stress corrosion cracking resistance of alloy 600 was evaluated in 10% sodium hydroxide solution with and without lead oxide at 315 C. The specimens of a C-ring type for stress corrosion cracking test were polarized at 150 mV above the corrosion potential for 120 hours without and with inhibitors such as titanium oxide, titanium boride, cerium boride. The chemical compositions of the films formed on the crack tip in the C-ring specimens were analyzed using a scanning Auger electron spectroscopy. The cerium boride, the most effective inhibitors, was observed to decrease the crack propagation rate more than a factor of three compared with that obtained in pure 10% NaOH solution. Furthermore, no SCC was observed in lead contaminated 10% NaOH solution by the addition of the cerium boride. (authors)

  18. Influence of silicate ions on the formation of goethite from green rust in aqueous solution

    International Nuclear Information System (INIS)

    Kwon, Sang-Koo; Kimijima, Ken'ichi; Kanie, Kiyoshi; Suzuki, Shigeru; Muramatsu, Atsushi; Saito, Masatoshi; Shinoda, Kozo; Waseda, Yoshio

    2007-01-01

    We investigated the influence of silicate ions on the formation of goethite converted from hydroxysulphate green rust, which was synthesized by neutralizing mixed solution of Fe 2 (SO 4 ) 3 and FeSO 4 with NaOH solution, by O 2 in an aqueous solution. The pH and oxidation-reduction potential of the suspension and the Fe and Si concentrations in supernatant solutions were analyzed. X-ray diffraction results for the solid particles formed during the conversion were consistent with the results of the solution analyses. The results indicated that silicate ions suppressed the conversion from green rust to α-FeOOH and distorted the linkages of FeO 6 octahedral units in the α-FeOOH structure

  19. Uranium in aqueous solutions by colorimetry

    International Nuclear Information System (INIS)

    Anon.

    1981-01-01

    The method covers the quantitative determination of uranium in known volumes of aqueous solutions that contain radioactive nuclides. These solutions arise from processing of irradiated nuclear fuel and from laboratory studies on irradiated uranium. The method is applicable to solutions containing a minimum of 30 μg of uranium per sample although as little as 0.5 μg can be detected but with lower precision. Highest precision is obtained with 50 to 75 μg of uranium in the test sample. Dilutions must be made at concentrations above 750 μg/ml. The method includes a discussion of photometers and photometric practice, apparatus, reagents, cell matching, preparation of standard curves, calibration by the method of internal standards, procedure, calculation, and precision

  20. NIR spectroscopic properties of aqueous acids solutions.

    Science.gov (United States)

    Omar, Ahmad Fairuz; Atan, Hanafi; Matjafri, Mohd Zubir

    2012-06-15

    Acid content is one of the important quality attributes in determining the maturity index of agricultural product, particularly fruits. Despite the fact that much research on the measurement of acidity in fruits through non-destructive spectroscopy analysis at NIR wavelengths between 700 to 1,000 nm has been conducted, the same response towards individual acids is not well known. This paper presents NIR spectroscopy analysis on aqueous citric, tartaric, malic and oxalic solutions through quantitative analysis by selecting a set of wavelengths that can best be used to measure the pH of the solutions. The aquaphotomics study of the acid solutions has generated R² above 0.9 for the measurement of all acids. The most important wavelengths for pH are located at 918-925 nm and 990-996 nm, while at 975 nm for water.

  1. Radiation-induced nitration of organic compounds in aqueous solutions

    International Nuclear Information System (INIS)

    Ershov, B.G.; Gordeev, A.V.; Bykov, G.L.; Moisy, P.

    2012-01-01

    Radiolysis in aqueous nitrate and acetic acid solutions and nitrate/nitric acid and phenol was studied. The radiolysis of these solutes occurs with circle NO 2 radical, which is the active nitrating agent. Accumulation of nitromethane and nitrite was determined during γ-irradiation of aqueous solutions containing acetic and nitrate solutions. Irradiation of aqueous phenol-nitrate/nitric acid solutions results in the formation of 2- and 4-nitrophenols.

  2. Radiation-induced nitration of organic compounds in aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Ershov, B.G.; Gordeev, A.V.; Bykov, G.L. [Russian Academy of Sciences, Moscow (Russian Federation). Frumkin Inst. of Physical Chemistry and Electrochemistry; Moisy, P. [CEA, Bagnols sur Ceze (France). Nuclear Energy Div.

    2012-07-01

    Radiolysis in aqueous nitrate and acetic acid solutions and nitrate/nitric acid and phenol was studied. The radiolysis of these solutes occurs with {sup circle} NO{sup 2} radical, which is the active nitrating agent. Accumulation of nitromethane and nitrite was determined during {gamma}-irradiation of aqueous solutions containing acetic and nitrate solutions. Irradiation of aqueous phenol-nitrate/nitric acid solutions results in the formation of 2- and 4-nitrophenols.

  3. Improvement of corrosion resistance in NaOH solution and glass forming ability of as-cast Mg-based bulk metallic glasses by microalloying

    Directory of Open Access Journals (Sweden)

    Peng Hao

    2011-02-01

    Full Text Available The influences of the addition of Ag on the glass forming ability (GFA and corrosion behavior were investigated in the Mg-Ni-based alloy system by X-ray diffraction (XRD and electrochemical polarization in 0.1 mol/L NaOH solution. Results shows that the GFA of the Mg-Ni-based BMGs can be improved dramatically by the addition of an appropriate amount of Ag; and the addition element Ag can improve the corrosion resistance of Mg-Ni-based bulk metallic glass. The large difference in atomic size and large negative mixing enthalpy in alloy system can contribute to the high GFA. The addition element Ag improves the forming speed and the stability of the passive film, which is helpful to decrease the passivation current density and to improve the corrosion resistance of Mg-Ni-based bulk metallic glass.

  4. Radiosensitization of thymidine in deaerated aqueous solution

    International Nuclear Information System (INIS)

    Berger, Maurice.

    1982-09-01

    This work investigates the mode of action of various radiosensitizing agents on the radio-induced degradation of thymidine in deaerated aqueous solution. A special effort was devoted to the separation of addition products formed by one of these substances (a stable nitroxide radical: TAN) with the radio-induced neutral radicals of thymidine. The complex mixture of different diastereoisomers resulting from the covalent addition of the TAN molecule on the thymidine carbons C (5) or C (6) was resolved by HPLC. The structural determination of these adducts (absolute configuration) was achieved by various spectroscopic techniques and specific chemical syntheses. A conformational study has been undertaken [fr

  5. 21 CFR 524.1200b - Kanamycin ophthalmic aqueous solution.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Kanamycin ophthalmic aqueous solution. 524.1200b... (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS OPHTHALMIC AND TOPICAL DOSAGE FORM NEW ANIMAL DRUGS § 524.1200b Kanamycin ophthalmic aqueous solution. (a) Specifications. The drug, which is in an aqueous...

  6. Peroxide coordination of tellurium in aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Mikhaylov, Alexey A.; Medvedev, Alexander G. [Kurnakov Institute of General and Inorganic Chemistry, Russian Academy of Sciences, Moscow (Russian Federation); The Casali Center of Applied Chemistry, The Institute of Chemistry, The Hebrew University of Jerusalem (Israel); Churakov, Andrei V.; Grishanov, Dmitry A.; Prikhodchenko, Petr V. [Kurnakov Institute of General and Inorganic Chemistry, Russian Academy of Sciences, Moscow (Russian Federation); Lev, Ovadia [The Casali Center of Applied Chemistry, The Institute of Chemistry, The Hebrew University of Jerusalem (Israel)

    2016-02-15

    Tellurium-peroxo complexes in aqueous solutions have never been reported. In this work, ammonium peroxotellurates (NH{sub 4}){sub 4}Te{sub 2}(μ-OO){sub 2}(μ-O)O{sub 4}(OH){sub 2} (1) and (NH{sub 4}){sub 5}Te{sub 2}(μ-OO){sub 2}(μ-O)O{sub 5}(OH).1.28 H{sub 2}O.0.72 H{sub 2}O{sub 2} (2) were isolated from 5 % hydrogen peroxide aqueous solutions of ammonium tellurate and characterized by single-crystal and powder X-ray diffraction analysis, by Raman spectroscopy and thermal analysis. The crystal structure of 1 comprises ammonium cations and a symmetric binuclear peroxotellurate anion [Te{sub 2}(μ-OO){sub 2}(μ-O)O{sub 4}(OH){sub 2}]{sup 4-}. The structure of 2 consists of an unsymmetrical [Te{sub 2}(μ-OO){sub 2}(μ-O)O{sub 5}(OH)]{sup 5-} anion, ammonium cations, hydrogen peroxide, and water. Peroxotellurate anions in both 1 and 2 contain a binuclear Te{sub 2}(μ-OO){sub 2}(μ-O) fragment with one μ-oxo- and two μ-peroxo bridging groups. {sup 125}Te NMR spectroscopic analysis shows that the peroxo bridged bitellurate anions are the dominant species in solution, with 3-40 %wt H{sub 2}O{sub 2} and for pH values above 9. DFT calculations of the peroxotellurate anion confirm its higher thermodynamic stability compared with those of the oxotellurate analogues. This is the first direct evidence for tellurium-peroxide coordination in any aqueous system and the first report of inorganic tellurium-peroxo complexes. General features common to all reported p-block element peroxides could be discerned by the characterization of aqueous and crystalline peroxotellurates. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  7. Principles of interactions in non-aqueous electrolyte solutions

    NARCIS (Netherlands)

    Lyklema, J.

    2013-01-01

    In this paper a review is presented on the molecular interactions in non-aqueous media of low dielectric permittivity. Qualitative and quantitative distinctions with aqueous solutions are emphasized. The reviewed themes include dispersion forces, dissociation and association equilibria,

  8. Efficient removal of Cd2+ from aqueous solutions using by-product of biodiesel production

    International Nuclear Information System (INIS)

    Ribeiro, Rita F.L.; Soares, Vitor C.; Costa, Letícia M.; Nascentes, Clésia C.

    2012-01-01

    Highlights: ► Sorbents were prepared from radish cake, a waste from biodiesel production. ► The chemical treatments used were simple, low-cost and enhanced the Cd 2+ sorption. ► The cadmium sorption process was evaluated by Freundlich and Langmuir models. ► Chemically treated radish cake is an excellent alternative for removal of Cd 2+ . ► Desorption studies demonstrated that the sorbent–metal interaction is reversible. - Abstract: In this study, chemically modified radish cake, a by-product of biodiesel production, was used to remove Cd 2+ from aqueous solutions. The chemical modification was carried out by treating the radish cake with citric acid (CRC), NaOH (NRC) or the combination of citric acid and NaOH (CNRC). The sorbents were characterized by elemental analysis, surface area analysis, infrared spectroscopy (FTIR), potentiometric titration (PT), scanning electron microscopy–energy dispersive spectroscopy (SEM–EDS), and thermogravimetric analysis (TGA). The effect of the chemical treatment and contact time on cadmium sorption was evaluated. The equilibrium data were analyzed using Freundlich and Langmuir models. The maximum sorption capacity obtained by the Langmuir isotherm was 58.5 mg/g and 64.10 mg/g for the CRC, and CNRC sorbents, respectively. Complete desorption of Cd 2+ was achieved using 0.1 mol/L HNO 3 . The results obtained demonstrate that chemically modified radish cake has potential as a sorbent for Cd 2+ removal from aqueous solutions.

  9. Catalyzed reduction of nitrate in aqueous solutions

    International Nuclear Information System (INIS)

    Haas, P.A.

    1994-08-01

    Sodium nitrate and other nitrate salts in wastes is a major source of difficulty for permanent disposal. Reduction of nitrate using aluminum metal has been demonstrated, but NH 3 , hydrazine, or organic compounds containing oxygen would be advantageous for reduction of nitrate in sodium nitrate solutions. Objective of this seed money study was to determine minimum conditions for reduction. Proposed procedure was batchwise heating of aqueous solutions in closed vessels with monitoring of temperatures and pressures. A simple, convenient apparatus and procedure were demonstrated for observing formation of gaseous products and collecting samples for analyses. The test conditions were 250 degree C and 1000 psi max. Any useful reduction of sodium nitrate to sodium hydroxide as the primary product was not found. The nitrate present at pHs 3 or NH 4 NO 3 is easily decomposed, and the effect of nitromethane at these low pHs was confirmed. When acetic acid or formic acid was added, 21 to 56% of the nitrate in sodium nitrate solutions was reduced by methanol or formaldehyde. With hydrazine and acetic acid, 73 % of the nitrate was decomposed to convert NaNO 3 to sodium acetate. With hydrazine and formic acid, 36% of the nitrate was decomposed. If these products are more acceptable for final disposal than sodium nitrate, the reagents are cheap and the conversion conditions would be practical for easy use. Ammonium acetate or formate salts did not significantly reduce nitrate in sodium nitrate solutions

  10. The reactivity of the electron formed in the radiolysis of aerated alkaline aqueous solutions containing tetracycline hydrochloride, at 77 Ksup(+)

    International Nuclear Information System (INIS)

    Guedes, S.M.L.; Vasconcellos, M.B.A.

    1986-01-01

    The radiolysis of tetracycline hydrochloride dissolved in aerated alkaline aqueous solutions containing 0.1, 0.5 and 1M NaOH at 77 K, followed by ESR is reported. The rate constants for the reactions between the electron and physical or chemical traps which are present in these solutions are calculated. The reactivity of electrons that are formed in the radiolysis of water decreases in the following proportions: physical traps: chemical traps: molecules of water (4.8x10sup(14) : 6.5x10sup(8) : 1.0). The electrons react preferentially with the solute instead of the solvent. (author)

  11. Determination of the solubility of Np(IV), Pu(III) - (VI),Am(III) - (VI), and Te(IV), (V) hydroxo compounds in 0.5 - 14 M NaOH solutions

    Energy Technology Data Exchange (ETDEWEB)

    Delegard, C.H.

    1996-09-24

    The solubilities of Am(III), Np(IV), Pu(IV), Tc(IV), Np(V), Pu(V), Am(V), and Tc(V) hydroxo compounds were studied in 0.5 to 14 M NaOH solutions at 25{+-}2 {degrees}C. The effects of fluoride, phosphate, carbonate, oxalate, and some other organic complexing agents on the solubilities of Np(IV), Pu(IV), and TC(IV) hydroxides were investigated at 1.0 and 4.0 M NAOH. Some predictions were made on the dissolved (I.V) and (V) species present in alkali solutions.

  12. Radiolysis of paracetamol in dilute aqueous solution

    International Nuclear Information System (INIS)

    Szabó, László; Tóth, Tünde; Homlok, Renáta; Takács, Erzsébet; Wojnárovits, László

    2012-01-01

    Using radiolytic experiments hydroxyl radical (main reactant in advanced oxidation processes) was shown to effectively destroy paracetamol molecules. The basic reaction is attachment to the ring. The hydroxy-cyclohexadienyl radical produced in the further reactions may transform to hydroxylated paracetamol derivatives or to quinone type molecules and acetamide. The initial efficiency of aromatic ring destruction in the absence of dissolved O 2 is c.a. 10%. The efficiency is 2–3 times higher in the presence of O 2 due to its reaction with intermediate hydroxy-cyclohexadienyl radical and the subsequent ring destruction reactions through peroxi radical. Upon irradiation the toxicity of solutions at low doses increases with the dose and then at higher doses it decreases. This is due to formation of compounds with higher toxicity than paracetamol (e.g. acetamide, hidroquinone). These products, however, are highly sensitive to irradiation and degrade easily. - Highlights: ► Paracetamol is easily degraded in aqueous solution by low dose irradiation. ► Main degradation products are hydroxylated molecules, acetamide and hydroquinone. ► Toxicity of solutions goes through a maximum as a function of dose.

  13. Radiolysis of paracetamol in dilute aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Szabo, Laszlo [Institute of Isotopes, Hungarian Academy of Sciences, Budapest (Hungary); Budapest University of Technology and Economics, Budapest (Hungary); Toth, Tuende [Budapest University of Technology and Economics, Budapest (Hungary); Homlok, Renata [Institute of Isotopes, Hungarian Academy of Sciences, Budapest (Hungary); Takacs, Erzsebet [Institute of Isotopes, Hungarian Academy of Sciences, Budapest (Hungary); Wojnarovits, Laszlo [Institute of Isotopes, Hungarian Academy of Sciences, Budapest (Hungary)

    2012-09-15

    Using radiolytic experiments hydroxyl radical (main reactant in advanced oxidation processes) was shown to effectively destroy paracetamol molecules. The basic reaction is attachment to the ring. The hydroxy-cyclohexadienyl radical produced in the further reactions may transform to hydroxylated paracetamol derivatives or to quinone type molecules and acetamide. The initial efficiency of aromatic ring destruction in the absence of dissolved O{sub 2} is c.a. 10%. The efficiency is 2-3 times higher in the presence of O{sub 2} due to its reaction with intermediate hydroxy-cyclohexadienyl radical and the subsequent ring destruction reactions through peroxi radical. Upon irradiation the toxicity of solutions at low doses increases with the dose and then at higher doses it decreases. This is due to formation of compounds with higher toxicity than paracetamol (e.g. acetamide, hidroquinone). These products, however, are highly sensitive to irradiation and degrade easily. - Highlights: Black-Right-Pointing-Pointer Paracetamol is easily degraded in aqueous solution by low dose irradiation. Black-Right-Pointing-Pointer Main degradation products are hydroxylated molecules, acetamide and hydroquinone. Black-Right-Pointing-Pointer Toxicity of solutions goes through a maximum as a function of dose.

  14. Formation and disappearance of superoxide radicals in aqueous solutions

    International Nuclear Information System (INIS)

    Allen, A.O.; Bielski, B.H.J.

    1980-01-01

    A literature review of superoxide radicals in aqueous solutions is presented covering the following: history; methods of formation of aqueous HO 2 /HO 2 - by radiolysis and photolysis, electrolysis, mixing nonaqueous solutions into water, chemical reactions, enzymatic generation of O 2 - , and photosensitization; and properties of HO 2 /O 2 - in aqueous solution, which cover spontaneous dismutation rates, pk and absorption spectra, catalyzed dismutation, thermodynamics and the so-called Haber-Weiss Reaction

  15. Effect of potential on the corrosion fatigue crack propagation of inconel 600 in 50% NaOH solution at 850C

    International Nuclear Information System (INIS)

    Misawa, Toshihei; Sugawara, Hideo; Harada, Tadashi

    1979-01-01

    A study has been made of corrosion fatigue crack growth for Inconel 600 solution-annealed at 1100 0 C for 0.5 h in 85 0 C 50% NaOH solution with a frequency of 1.1 cycle per minute. The effect of potential on the corrosion fatigue crack growth rate (da/dN) as a function of ΔK was examined and the fracture surfaces were observed. The results obtained are as follows: (1) The crack growth rate and the cracking mode were affected by the applied potentials in the anodic polarization curve. The value of da/dN was arranged in the following order of the observed potentials: secondary passive region > corrosion potential > primary active region > primary passive region. (2) Intergranular cracking took place at a secondary passive potential (-0.04 V vs SCE) which gave a maximum crack growth rate. Transgranular cracking with fatigue striations occurred at the other potentials. (3) The variation in current with the alternating loading was observed at the potentials where transgranular cracking occurred, whereas no appreciable correlation between current and cyclic loading was shown at a potential of -0.04 V where the intergranular mode cracking occurred. (4) It is pointed out to be helpful in studying the influence of applied potential on the accelerated rate of cracking at the crack tip by the ''crack-tip opening displacement'' estimated from the stress intensity, as the major mechanical condition. (author)

  16. Study of the radiolysis of tetracycline hidrochloride in aerated aqueous solutions

    International Nuclear Information System (INIS)

    Guedes, S.M.L.; Vasconcellos, M.B.A.

    1983-01-01

    The radiolysis of tetracycline hydrochloride (TC) was studied in neutral, acid and alkaline aerated solutions, by electron spin resonance spectroscopy at 77K. The paramagnetic species observed are: H.; OH.; HO 2 .; e - trapped and impurity radical. The reaction mechanism shows that the solute reacts with the solvent before the radiolysis and produces H + ions, as a consequence of the ionization of tricarbonylmethane group. The H + ions react with the e - from the radiolysis of water and produce HO 2 in the presence of O 2 . The interaction of TC with the alkaline solvent favours the interaction between gamma rays and solute. The products formed in the interaction of solute with the solvent before the radiolysis, as a consenquence of the ionization of TC, according to the pH of the solution, are of fundamental importance in the interaction of gamma rays with the solute. A crude estimate of the average distance that the e - is able to travel through solvent molecules before its capture by the solute was obtained in these 0.1N, 0.5N and 1.0N NaOH aqueous solutions. Until [TC] - travels more in solutions that contain less [NaOH]. In higher [TC] the e - travels through 680 solvent molecules. In order to explain the selective capture of the e3- by solute molecules, a simple model is suggested based on the existence of channel walls of solvent molecules where the electrical atraction betwwed Na + and e - influences the collision frequency and the energy loss. (Author) [pt

  17. Pulse radiolysis of bilirubin in aqueous solution

    International Nuclear Information System (INIS)

    Barber, D.J.W.; Richards, J.T.

    1977-01-01

    A pulse radiolysis study of bilirubin, the breakdown product of heme, has been made. In aqueous solution at pH 12, short-lived transient spectra have been obtained for reaction of bilirubin with e/sub aq//sup -/ and OH. Bimolecular rate constants for these reactions have been measured, namely, k/sub BR+e/sub aq//sup -/ equals 9.5 x 10 9 M -1 sec -1 and k/sub BR+OH/ equals 3.45 x 10 9 M -1 sec -1 , and the spectrum of a long-lived product resulting from decay of the bilirubin-OH adduct has been obtained. In addition, solute destruction by OH has been investigated in detail. The transient absorption spectrum for reduction of bilirubin with the H atom at neutral pH has been measured. By measuring the rate of reaction with e/sub aq//sup -/ in the presence of bovine serum albumin (BSA), the mode of binding of bilirubin to this biologically important compound has been studied

  18. Flotation separation of PET from a PET, PVC and PS mixture by the hydrofilization of the PET surface in NaOH solutions

    Directory of Open Access Journals (Sweden)

    Ľubica Kozáková

    2005-11-01

    Full Text Available Recycling is the most effective method of waste minimization created by the human activity. The idea of waste re-use as a result of environmental, social and economical factors is becoming very relevant in the last decades. The portion of plastics in the municipal waste is growing year by year as also is its use in the wrapping industry. A condition for recycling technologies is the input of highly pure plastics (without undesirable admixtures suitable for recycling. Various separation technologies can be used which provide separation of particular components of plastic waste and contaminants. Flotation is one of the separation methods used especially for the ore beneficiation but recently is widely also used for the separation of various types of waste. Plastics, which are not possible to be separated by gravitational methods (because they have almost the same density, PET from beverage bottles, PVC from bottles and foils and PS from beverage beakers, were studied. By changing the surface properties of PET from naturally hydrophobic to hydrophilic by the adjustment in a NaOH solution, PET with the recovery of up to 99 % in the non-foamy product and with the product purity of up to 98 % was acquired by the flotation.

  19. Acetic acid extraction from aqueous solutions using fatty acids

    NARCIS (Netherlands)

    IJmker, H.M.; Gramblicka, M.; Kersten, Sascha R.A.; van der Ham, Aloysius G.J.; Schuur, Boelo

    2014-01-01

    A major challenge for production of acetic acid via bio-based routes is cost-effective concentration and purification of the acetic acid from the aqueous solutions, for which liquid–liquid extraction is a possible method. A main challenge in extraction of acetic acid from dilute aqueous solutions is

  20. Estabilidade da sílica biogênica extraída de capim Jaraguá (Hyparrhenia rufa em solução de NaOH Stability of biogenic silica extract of Jaraguá grass (Hyparrhenia rufa in NaOH solution

    Directory of Open Access Journals (Sweden)

    Liovando M. Costa

    2010-01-01

    Full Text Available Biogenic silica is used to describe compounds of hydrated silica (SiO2.nH2O, with specific shapes and sizes, deposited in plants. The chemical composition of biogenic silica and its stability in Jaraguá grass was studied in increasing concentration of NaOH. The analytical results demonstrated high concentration of Si, Al, Fe, Mg, P and low of Cu, Cd and Zn in the phytoliths composition. The silica bodies stability in NaOH solution with increasing concentration was different among the shapes and sizes. Silicified stomata and silicified plant tissues were dissolved along with the dumbbells because they are the less stable forms of biogenic silica.

  1. Pulse radiolysis study of aqueous cyanamide solutions

    International Nuclear Information System (INIS)

    Draganic, I.G.; Draganic, Z.D.; Sehested, K.

    1978-01-01

    The radiolysis of oxygen-free, aqueous solutions of cyanamide was studied by fast kinetic spectrophotometry. Computer simulation of the reaction mechanisms was used to evaluate the experimental data. Four different species are identified: (1) the radical anion (NH 2 CN) - absorbing light in the UV with lambda/sub max/ 240 = 1500 M -1 cm -1 ; the disappearance is a second-order process with 2k = 1.3 x 10 9 M -1 s -1 ; (2) the hydrogen adduct, NH 2 C(H) double bond N (or NH 2 C double bond NH), with lambda/sub max/ 300 nm and epsilon 300 = 150 M -1 cm -1 decaying by second-order kinetics with 2k = 3.1 x 10 9 M -1 s -1 ; (3) the hydroxyl radical preferentially adds to the cyano group, NH 2 C(OH) double bond N (or NH 2 C double bond NOH). This species rearranges in the submicrosecond scale to NH 2 C ( double bond O) NH (lambda/sub max/ 325 nm and epsilon/sub 325 = 1900 M -1 cm -1 ) and disappears by a second-order process with 2k = 6.3 x 10 9 M -1 s -1 . (4) It is estimated that about 10% of OH radicals attack the substituent group and by H abstraction produce the NHCN radical (lambda/sub max/ 370 nm and epsilon 370 = 1800 M -1 cm -1 ); it disappears by a pseudo-first-order process attributed to a hydrolysis reaction. At increasing acidities, protonation of this radical takes place, NHCN + H + → + NH 2 CN; the protonated form decays faster and absorbs more strongly. In a cyanamide solution containing S 2 O 8 2- , the SO - 4 . radicals react with cyanamide, k = 1 x 10 8 M -1 s -1 , producing + NH 2 CN radicals. The dependence of the optical density at 325 nm on the dose rate and solute concentration are quantitatively consistent with the assumption that the OH radicals react with the NH 2 C(=O)NH species with k = 4 x 10 9 M -1 s -1

  2. Study on corrosion of carbon steel in DEA aqueous solutions

    Science.gov (United States)

    Yang, Jun Han; Xie, Jia Lin; Zhang, Li

    2018-02-01

    Corrosion of carbon steel in the CO2 capture process using diethanolamine (DEA) aqueous solutions was investigated. The effects of the mass concentrations of DEA, solution temperature and CO2 loading on the corrosion rate of carbon steel were demonstrated. The experimental results provided comprehensive information on the appropriate concentration range of DEA aqueous solutions under which low corrosion of carbon steel can be achieved.

  3. Reverse osmosis separation of radium from dilute aqueous solutions

    International Nuclear Information System (INIS)

    Subramanian, K.S.; Sastri, V.S.

    1980-01-01

    Porous cellulose acetate membranes obtained from Osmonics Inc. were characterized in terms of pure water permeability constant, solute transport parameter, and mass transfer coefficient with aqueous sodium chloride solution as the reference system. Reverse osmosis separation behavior of radium-226 as nitrate, chloride, and sulfate salts was studied. Reverse osmosis method of removing radium-226 from aqueous solutions has been compared with other methods, and it has been shown to be one of the best methods for alleviating radium contamination problems

  4. Thermophysical Properties of Aqueous Solutions Used as Secondary Working Fluids

    OpenAIRE

    Melinder, Åke

    2007-01-01

    Secondary working fluids (secondary refrigerants, heat transfer fluids, antifreezes, brines) have long been used in various indirect re-frigeration and heat pump systems. Aqueous solutions (water solu-tions) have long been used as single phase (liquid only) secondary working fluids for cooling in supermarkets, ice rinks, heat recovery systems, heat pumps and other applications. However, aqueous solutions are increasingly used also for freezers in supermarkets and other applications in low tem...

  5. Radiolysis of aqueous solutions of insulin. [. gamma. rays

    Energy Technology Data Exchange (ETDEWEB)

    Foitik, A [Ceskoslovenska Akademie Ved, Prague. Ustav Fyzikalni Chemie a Elektrochemie J. Heyrovskeho; Kopoldova, J [Ceskoslovenska Akademie Ved, Prague. Isotopova Laborator Biologickych Ustavu

    1976-08-01

    The effect of ionizing radiation on diluted aqueous solutions of insulin is analyzed. The rate of decrease in its level (the loss of polarographic activity) is described by a first-order kinetic equation. The results lead to the concept of a direct effect on macromolecules in 'excited volumes'. The amount of inactivated molecules (i.e., the yield) in this volume is proportional to the solute concentration. In diluted aqueous solutions indirect radiation effects also take place. The paper evaluates these effects.

  6. Heavy metal removal from aqueous solutions by sorption using ...

    African Journals Online (AJOL)

    Heavy metal removal from aqueous solutions by sorption using natural clays from Burkina Faso. ... The high alkaline pH in one of the samples is attributable to the presence of ... The point of zero charge (pHpzc) values of the clays, as determined by ... significant contributions to the removal of metal ions in aqueous systems.

  7. Reactions of alkylnitrosoureas in aqueous solution

    International Nuclear Information System (INIS)

    Snyder, J.K.; Stock, L.M.

    1980-01-01

    The acid- and base-catalyzed decompositions of N-methyl-,N,N'-dimethyl-, and N,N',N'-trimethyl-N-nitrosourea in aqueous solution have been studied. Below pH 2, the N-methyl compound undergoes both denitrosation and hydrolysis to yield methylurea, nitrous acid, methylamine, nitrogen, and carbon dioxide. The acid-catalyzed denitrosation and hydrolysis of the trimethylnitrosourea are somewhat more rapid than the corresponding reactions of N-methyl-N-nitrosourea. The solvent isotope effect, k/sub H 2 O//k/sub D 2 O/ = 1.3, and the absence of chloride ion catalysis suggest that the denitrosation reaction proceeds by a rate-determining proton transfer which is followed by the rapid loss of the nitroso group. The results for the hydrolysis reaction are compatible with a formulation in which a hydrate of the nitrosourea is protonated in a rate-determining step to form a tetrahedral intermediate which subsequently decomposes to yield methyldiazonium hydroxide and a carbamic acid derivative. The base-catalyzed reactions of the mono, di-, and trimethylnitrosoureas are first order in hydroxide ion over a broad pH range. The hydrolysis of N-methyl-N-nitrosourea yields methanol and derivatives of carbamic acid. Salt effects on the reaction rate are negligible except for the influence of lithium ion. The rate constants for the hydrolysis of the mono- and dimethyl compounds depend upon the buffer concentrationat pH 9.5. The rate constants for the hydrolysis of the trimethyl compound also depend upon the buffer concentration, but a limiting value is not achieved. The solvent isotope effect for the base-catalyzed reaction, the exchange reaction of water- 18 O with the carbonyl group of the urea, and the fact that N-methyl-N-nitrosourea is hydrolyzed about 2.2 x 10 4 times more rapidly than N,N',N'-trimethyl-N-nitrosourea suggest that the hydrolysis occurs by a mechanism in which a tetrahedral intermediate is formed

  8. Cast iron deterioration with time in various aqueous salt solutions

    Indian Academy of Sciences (India)

    Unknown

    various aqueous salt solutions have been carried out using total immersion test ... circuit potential, Icorr, Tafel slopes, corrosion rate, have been calculated by standard methods. ..... Rao B V S 1980 in Maintenance for reliability (Bombay: Media.

  9. Biosorptive removal of cobalt (II) ions from aqueous solution by ...

    African Journals Online (AJOL)

    hope&shola

    2010-11-29

    Nov 29, 2010 ... chemical reaction, decay, adsorption and biodegradation. The presence of ... sted coffee (Dakiky et al., 2002), waste tea (Ahluwalia and Goyal, 2005) ..... green removal from aqueous solution by citric acid modified rice straw.

  10. Removal of boron from aqueous solution using cryptocrystalline magnesite

    CSIR Research Space (South Africa)

    Masindi, Vhahangwele

    2016-05-01

    Full Text Available of Water Reuse and Desalination Removal of boron from aqueous solution using cryptocrystalline magnesite Vhahangwele Masindi and Mugera W. Gitari Abstract The present study aimed to evaluate the efficiency of using cryptocrystalline magnesite...

  11. Separation of cesium from aqueous solutions using alkylated tetraaryl borates

    International Nuclear Information System (INIS)

    Feldmaier, F.

    1991-01-01

    The water solubility of cesium tetraaryl borates was lowered by introducing hydrophobic aliphatic side chains into corresponding acid-resistant fluorosubstituted tetraaryl borates. This improved cesium spearability both in precipitation and in extraction from aqueous solutions. (orig.) [de

  12. (CI 42053) from an aqueous solution using Azadirachta indica leaf

    African Journals Online (AJOL)

    STORAGESEVER

    2008-11-05

    Nov 5, 2008 ... ... 42053) from an aqueous solution using Azadirachta indica leaf powder as a low- ... and biodegradable effective adsorbents. They were ob- tained from ... pesticide. The trees are also known as an air purifier. The medicinal.

  13. Detection of the electronic structure of iron-(iii)-oxo oligomers forming in aqueous solutions.

    Science.gov (United States)

    Seidel, Robert; Kraffert, Katrin; Kabelitz, Anke; Pohl, Marvin N; Kraehnert, Ralph; Emmerling, Franziska; Winter, Bernd

    2017-12-13

    The nature of the small iron-oxo oligomers in iron-(iii) aqueous solutions has a determining effect on the chemical processes that govern the formation of nanoparticles in aqueous phase. Here we report on a liquid-jet photoelectron-spectroscopy experiment for the investigation of the electronic structure of the occurring iron-oxo oligomers in FeCl 3 aqueous solutions. The only iron species in the as-prepared 0.75 M solution are Fe 3+ monomers. Addition of NaOH initiates Fe 3+ hydrolysis which is followed by the formation of iron-oxo oligomers. At small enough NaOH concentrations, corresponding to approximately [OH]/[Fe] = 0.2-0.25 ratio, the iron oligomers can be stabilized for several hours without engaging in further aggregation. Here, we apply a combination of non-resonant as well as iron 2p and oxygen 1s resonant photoelectron spectroscopy from a liquid microjet to detect the electronic structure of the occurring species. Specifically, the oxygen 1s partial electron yield X-ray absorption (PEY-XA) spectra are found to exhibit a peak well below the onset of liquid water and OH - (aq) absorption. The iron 2p absorption gives rise to signal centered between the main absorption bands typical for aqueous Fe 3+ . Absorption bands in both PEY-XA spectra are found to correlate with an enhanced photoelectron peak near 20 eV binding energy, which demonstrates the sensitivity of resonant photoelectron (RPE) spectroscopy to mixing between iron and ligand orbitals. These various signals from the iron-oxo oligomers exhibit maximum intensity at [OH]/[Fe] = 0.25 ratio. For the same ratio, we observe changes in the pH as well as in complementary Raman spectra, which can be assigned to the transition from monomeric to oligomeric species. At approximately [OH]/[Fe] = 0.3 we begin to observe particles larger than 1 nm in radius, detected by small-angle X-ray scattering.

  14. Surface tension and related thermodynamic quantities of aqueous electrolyte solutions

    CERN Document Server

    Matubayasi, Norihiro

    2013-01-01

    Surface tension provides a thermodynamic avenue for analyzing systems in equilibrium and formulating phenomenological explanations for the behavior of constituent molecules in the surface region. While there are extensive experimental observations and established ideas regarding desorption of ions from the surfaces of aqueous salt solutions, a more successful discussion of the theory has recently emerged, which allows the quantitative calculation of the distribution of ions in the surface region. Surface Tension and Related Thermodynamic Quantities of Aqueous Electrolyte Solutions provides a d

  15. γ-Irradiation-induced radiolysis of inulin in aqueous solutions

    International Nuclear Information System (INIS)

    Tsyba, I.A.; Revina, A.A.; Shostenko, A.G.

    1997-01-01

    Radiochemical transformations of inulin in aqueous solutions, in air, in the presence of inert gases, helium, nitrogen and in nitrous oxide exposed to various doses of 60 Co γ-irradiation were investigated. It was shown that interactions in inulin with OH radicals are principally responsible for radiolytic decomposition of inulin. The data on radiolysis of more simple model systems were used to make available decomposition spectra of γ-irradiated aerated aqueous solution of inulin. 9 refs., 6 figs

  16. Adsorption of lead from aqueous solutions by poly (methyl methacrylate)

    International Nuclear Information System (INIS)

    Din, M.; Hussain, R.

    1992-01-01

    The adsorption capability of commercially manufactured poly (methyl methacrylate) for lead in aqueous medium has been investigated. Percent adsorption and distribution coefficient values have been determined in relation to the shaking time, amount of adsorbent, pH effects and concentration of lead in the solution. The experimental results are compatible with Freundlich type of adsorption behavior. It is discernible from the experimental results that poly (methyl methacrylate) can be used for the removal of lead from slightly acidic aqueous solutions. (author)

  17. EXTRACTION OF MONOAZO DYES BY HYDROPHILIC EXTRACTANTS FROM AQUEOUS SOLUTIONS

    Directory of Open Access Journals (Sweden)

    Y. I. Korenman

    2012-01-01

    Full Text Available The extraction of mono azo dyes E102, E122, E110, E124, E129 from aqueous solutions with hydrophilic solvents (alcohols, esters, ketones and polymers (poly-N-vinylamides, polyethylene glycol was studied. The main regularities of extraction are established. The distribution coefficients and degree of extraction of dyes was estimate. The influence of the nature of solvents and polymers on the extraction of dyes from aqueous solutions are established.

  18. Thermodynamic properties of aqueous hydroxyurea solutions

    International Nuclear Information System (INIS)

    Kumar, Shekhar; Sinha, Pranay Kumar; Kamachi Mudali, U.; Natarajan, R.

    2011-01-01

    Hydroxyurea is a novel reductant for uranium-plutonium separation in PUREX process. Little information on its thermophysical properties is available in published literature. In this work, its contributions to aqueous density, apparent molal volume, vapour pressure and thermodynamic water activity values, derived from in-house experiments, are reported. (author)

  19. Photolysis of Periodate and Periodic Acid in Aqueous Solution

    DEFF Research Database (Denmark)

    Sehested, Knud; Kläning, U. K.

    1978-01-01

    The photochemistry of periodate and periodic acid in aqueous solution was studied (i) by quantum yield measurements at low light intensity (ii) by flash photolysis, and (iii) by photolysis of glassy samples at 77 K. The photochemical studies were supplemented with pulse radiolysis studies...... of aqueous periodate solutions and with kinetic studies using stopped-flow technique. In strongly alkaline solution the photodecomposition of periodate proceeds via formation of O– and IVI. At pH solution O3 P is formed in a small...

  20. Knudsen thermogravimetry approach to the thermodynamics of aqueous solutions

    International Nuclear Information System (INIS)

    Schiraldi, Alberto; Signorelli, Marco; Fessas, Dimitrios

    2013-01-01

    Highlights: ► Knudsen cells were designed to replace standard TG pans for desorption experiments. ► The Knudsen effusion data allow determination of water activity of aqueous solutions. ► This methods can replace the traditional isopiestic approach for aqueous solutions. ► The Gibbs–Duhem relationship was used to fit the experimental data. -- Abstract: The use of isothermal TGA with Knudsen-like cells allows determination of the thermodynamic activity of water, a W . The typical experiment implies a slow dehydration of the aqueous solution at constant temperature in dynamic vacuum conditions. The method is alternative to the classical isopiestic approach and offers the advantage of a continuous record on increasing the solute concentration. These data can be directly treated according to the classical thermodynamic relationships drawn from the Gibbs–Duhem expression to evaluate the activity and osmotic coefficient of the aqueous solutions of electrolytes and non-electrolytes, and, in the case of electrolytes, allow determination of solubility of the solute. Discrepancies with respect to the literature data are observed when the viscosity of the systems becomes too high, as in the case of sugars with a very large solubility. Such a mismatch may however be accounted for either slowing the dehydration rate with use of a narrower Knudsen orifice, or correcting the experimental a W with a calibration curve. The same approach can be applied to non-aqueous solutions

  1. Gold nanoparticles prepared by electro-exploding wire technique in aqueous solutions

    Science.gov (United States)

    Kumar, Lalit; Kapoor, Akanksha; Meghwal, Mayank; Annapoorni, S.

    2016-05-01

    This article presents an effective approach for the synthesis of Au nanoparticles via an environmentally benevolent electro-exploding wire (EEW) technique. In this process, Au nanoparticles evolve through the plasma generated from the parent Au metal. Compared to other typical chemical methods, electro-exploding wire technique is a simple and economical technique which normally operates in water or organic liquids under ambient conditions. Efficient size control was achieved using different aqueous medium like (1mM) NaCl, deionized water and aqueous solution of sodium hydroxide (NaOH, pH 9.5) using identical electro-exploding conditions. The gold nanoparticles exhibited the UV-vis absorption spectrum with a maximum absorption band at 530 nm, similar to that of gold nanoparticles chemically prepared in a solution. The mechanism of size variation of Au nanoparticles is also proposed. The results obtained help to develop methodologies for the control of EEW based nanoparticle growth and the functionalization of nanoparticle surfaces by specific interactions.

  2. Neptunium carbonato complexes in aqueous solution: an electrochemical, spectroscopic, and quantum chemical study.

    Science.gov (United States)

    Ikeda-Ohno, Atsushi; Tsushima, Satoru; Takao, Koichiro; Rossberg, André; Funke, Harald; Scheinost, Andreas C; Bernhard, Gert; Yaita, Tsuyoshi; Hennig, Christoph

    2009-12-21

    The electrochemical behavior and complex structure of Np carbonato complexes, which are of major concern for the geological disposal of radioactive wastes, have been investigated in aqueous Na(2)CO(3) and Na(2)CO(3)/NaOH solutions at different oxidation states by using cyclic voltammetry, X-ray absorption spectroscopy, and density functional theory calculations. The end-member complexes of penta- and hexavalent Np in 1.5 M Na(2)CO(3) with pH = 11.7 have been determined as a transdioxo neptunyl tricarbonato complex, [NpO(2)(CO(3))(3)](n-) (n = 5 for Np(V), and 4 for Np(VI)). Hence, the electrochemical reaction of the Np(V/VI) redox couple merely results in the shortening/lengthening of bond distances mainly because of the change of the cationic charge of Np, without any structural rearrangement. This explains the observed reversible-like feature on their cyclic voltammograms. In contrast, the electrochemical oxidation of Np(V) in a highly basic carbonate solution of 2.0 M Na(2)CO(3)/1.0 M NaOH (pH > 13) yielded a stable heptavalent Np complex of [Np(VII)O(4)(OH)(2)](3-), indicating that the oxidation reaction from Np(V) to Np(VII) in the carbonate solution involves a drastic structural rearrangement from the transdioxo configuration to a square-planar-tetraoxo configuration, as well as exchanging the coordinating anions from carbonate ions (CO(3)(2-)) to hydroxide ions (OH(-)).

  3. Utilization of fermentation waste (Corynebacterium glutamicum) for biosorption of Reactive Black 5 from aqueous solution

    International Nuclear Information System (INIS)

    Vijayaraghavan, K.; Yun, Yeoung-Sang

    2007-01-01

    A fermentation waste, Corynebacterium glutamicum, was successfully employed as a biosorbent for Reactive Black 5 (RB5) from aqueous solution. This paper initially studied the effect of pretreatment on the biosorption capacity of C. glutamicum toward RB5, using several chemical agents, such as HCl, H 2 SO 4 , HNO 3 , NaOH, Na 2 CO 3 , CaCl 2 and NaCl. Among these reagents, 0.1 M HNO 3 gave the maximum enhancement of the RB5 uptake, exhibiting 195 mg/g at pH 1 with an initial RB5 concentration of 500 mg/l. The solution pH and temperature were found to affect the biosorption capacity, and the biosorption isotherms derived at different pHs and temperatures revealed that a low pH (pH 1) and high temperature (35 deg. C) favored biosorption. The biosorption isotherm was well represented using three-parameter models (Redlich-Peterson and Sips) compared to two-parameter models (Langmuir and Freundlich models). As a result, high correlation coefficients and low average percentage error values were observed for three-parameter models. A maximum RB5 uptake of 419 mg/g was obtained at pH 1 and a temperature of 35 deg. C, according to the Langmuir model. The kinetics of the biosorption process with different initial concentrations (500-2000 mg/l) was also monitored, and the data were analyzed using pseudo-first and pseudo-second order models, with the latter describing the data well. Various thermodynamic parameters, such as ΔG o , ΔH o and ΔS o , were calculated, indicating that the present system was a spontaneous and endothermic process. The use of a 0.1 M NaOH solution successfully desorbed almost all the dye molecules from dye-loaded C. glutamicum biomass at different solid-to-liquid ratios examined

  4. Sonolysis of chlorinated compounds in aqueous solution.

    Science.gov (United States)

    Lim, Myung Hee; Kim, Seung Hyun; Kim, Young Uk; Khim, Jeehyeong

    2007-02-01

    To examine the reaction rates of sonochemical degradation of aqueous phase carbon tetrachloride, trichloroethylene and 1,2,3-trichloropropane at various temperatures, power intensities, and saturating gases, the batch tests were carried out. The degradations of chlorinated hydrocarbons were analyzed as pseudo first order reactions and their reaction rate constants were in the range of 10(-1)-10(-3)/min. The reaction was fast at the low temperature with higher power intensity. Also, the reaction went fast with the saturating gas with high specific heat ratio, high solubility and low thermal conductivity. The main mechanism of destruction of chemicals was believed the thermal combustion in the bubble.

  5. Investigation of ionizing radiation effect on albumin aqueous solutions

    International Nuclear Information System (INIS)

    Sizikov, A.M.; Adeeva, L.N.; Ogryzkova, I.F.

    1986-01-01

    Gamma radiation effect on 0.1-0.5%-albumin aqueous solutions has been investigated; variations of viscosity and optical density of solutions at pH medium different values and completeness of protein separation owing to radiation coagulation have been determined. It is shown that due to radiation coagulation it is possible to quantitatively separate albumin from irradiated aqueous solutions. The albumin coagulation is caused by OH radicals the action of which on albumin macromolecules results in destruction of intramolecular bonds and albumin conformation transformations

  6. Acidities of Water and Methanol in Aqueous Solution and DMSO

    Science.gov (United States)

    Gao, Daqing

    2009-01-01

    The relative acidities of water and methanol have been a nagging issue. In gas phase, methanol is more acidic than water by 36.0 kJ/mol; however, in aqueous solution, the acidities of methanol and water are almost identical. The acidity of an acid in solution is determined by both the intrinsic gas-phase ionization Gibbs energy and the solvent…

  7. Radiation-induced nitration of organic compounds in aqueous solutions

    International Nuclear Information System (INIS)

    Ershov, B.G.; Gordeev, A.V.; Bykov, G.L.

    2009-01-01

    Radiation-induced nitration of organic compounds in aqueous solutions was studied. It was found that γ-irradiation of solutions containing acetic and nitric acid and/or their salts gives nitromethane. Dependences of the product yield on the absorbed dose and the contents of components were established. The mechanism of radiation nitration involving radicals is discussed. (author)

  8. The separation of uranium ions by natural and modified diatomite from aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Sprynskyy, Myroslav, E-mail: sprynsky@yahoo.com [Department of Environmental Chemistry and Bioanalytics, Faculty of Chemistry, Nicolaus Copernicus University, 7 Gagarina Str., 87-100 Torun (Poland); Kovalchuk, Iryna [Department of Environmental Chemistry and Bioanalytics, Faculty of Chemistry, Nicolaus Copernicus University, 7 Gagarina Str., 87-100 Torun (Poland); Institute of Adsorption and Problem of Endoecology, National Academy of Sciences of Ukraine, 13 General Naumov Str., 03164 Kyiv (Ukraine); Buszewski, Boguslaw [Department of Environmental Chemistry and Bioanalytics, Faculty of Chemistry, Nicolaus Copernicus University, 7 Gagarina Str., 87-100 Torun (Poland)

    2010-09-15

    In this work the natural and the surfactant modified diatomite has been tested for ability to remove uranium ions from aqueous solutions. Such controlling factors of the adsorption process as initial uranium concentration, pH, contact time and ionic strength have been investigated. Effect of ionic strength of solution has been examined using the solutions of NaCl, Na{sub 2}CO{sub 3} and K{sub 2}SO{sub 4}. The pseudo-first order and the pseudo-second order models have been used to analyze the adsorption kinetic results, whereas the Langmuir and the Freundlich isotherms have been used to the equilibrium adsorption data. The effects of the adsorbent modification as well as uranium adsorption on the diatomite surface have been studied using X-ray powder diffraction, scanning electron microscopy and FTIR spectroscopy. The maximum adsorption capacities of the natural and the modified diatomite towards uranium were 25.63 {mu}mol/g and 667.40 {mu}mol/g, respectively. The desorptive solutions of HCl, NaOH, Na{sub 2}CO{sub 3}, K{sub 2}SO{sub 4}, CaCO{sub 3}, humic acid, cool and hot water have been tested to recover uranium from the adsorbent. The highest values of uranium desorption (86%) have been reached using 0.1 M HCl.

  9. The separation of uranium ions by natural and modified diatomite from aqueous solution.

    Science.gov (United States)

    Sprynskyy, Myroslav; Kovalchuk, Iryna; Buszewski, Bogusław

    2010-09-15

    In this work the natural and the surfactant modified diatomite has been tested for ability to remove uranium ions from aqueous solutions. Such controlling factors of the adsorption process as initial uranium concentration, pH, contact time and ionic strength have been investigated. Effect of ionic strength of solution has been examined using the solutions of NaCl, Na(2)CO(3) and K(2)SO(4). The pseudo-first order and the pseudo-second order models have been used to analyze the adsorption kinetic results, whereas the Langmuir and the Freundlich isotherms have been used to the equilibrium adsorption data. The effects of the adsorbent modification as well as uranium adsorption on the diatomite surface have been studied using X-ray powder diffraction, scanning electron microscopy and FTIR spectroscopy. The maximum adsorption capacities of the natural and the modified diatomite towards uranium were 25.63 micromol/g and 667.40 micromol/g, respectively. The desorptive solutions of HCl, NaOH, Na(2)CO(3), K(2)SO(4), CaCO(3), humic acid, cool and hot water have been tested to recover uranium from the adsorbent. The highest values of uranium desorption (86%) have been reached using 0.1M HCl. Copyright 2010 Elsevier B.V. All rights reserved.

  10. Structure of water and the thermodynamics of aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Nemethy, G.

    1970-10-26

    This report represents the summary of a series of lectures held at the Istituto Superiore di Sanita, Laboratori di Fisica, from 18 September to 26 October 1970. The topics discussed were: Intermolecular forces, the individual water molecule and the hydrogen bond, the structures of the solid phases of water, experimental information on the strucuture of liquid water, theoretical models of water structure, experimental properties and theoretical models of aqueous solutions of nonpolar solutes, polar solutes, and electrolytes, the conformational stability of biological macromolecules.

  11. Flotation separation of hafnium(IV) from aqueous solutions

    International Nuclear Information System (INIS)

    Downey, D.M.; Narick, C.N.; Cohen, T.A.

    1985-01-01

    A simple, rapid method for the separation of hafnium from aqueous solutions was investigated using sup(175+181)Hf tracer. Cationic hafnium complex ions were floated from dilute acid solutions with sodium lauryl sulfate (SLS) and anionic hafnium complexes were floated from basic and oxalic acid solutions with hexadecyltrimethyl ammonium bromide (HTMAB). The conditions necessary for quantitative recovery of the metal and mechanisms of flotation are described. (author)

  12. Flotation separation of hafnium(IV) from aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Downey, D.M.; Narick, C.N.; Cohen, T.A.

    1985-09-01

    A simple, rapid method for the separation of hafnium from aqueous solutions was investigated using sup(175 + 181)Hf tracer. Cationic hafnium complex ions were floated from dilute acid solutions with sodium lauryl sulfate (SLS) and anionic hafnium complexes were floated from basic and oxalic acid solutions with hexadecyltrimethyl ammonium bromide (HTMAB). The conditions necessary for quantitative recovery of the metal and mechanisms of flotation are described. (author). 21 refs.; 5 figs.

  13. Vibrational and orientational dynamics of water in aqueous hydroxide solutions.

    Science.gov (United States)

    Hunger, Johannes; Liu, Liyuan; Tielrooij, Klaas-Jan; Bonn, Mischa; Bakker, Huib

    2011-09-28

    We report the vibrational and orientational dynamics of water molecules in isotopically diluted NaOH and NaOD solutions using polarization-resolved femtosecond vibrational spectroscopy and terahertz time-domain dielectric relaxation measurements. We observe a speed-up of the vibrational relaxation of the O-D stretching vibration of HDO molecules outside the first hydration shell of OH(-) from 1.7 ± 0.2 ps for neat water to 1.0 ± 0.2 ps for a solution of 5 M NaOH in HDO:H(2)O. For the O-H vibration of HDO molecules outside the first hydration shell of OD(-), we observe a similar speed-up from 750 ± 50 fs to 600 ± 50 fs for a solution of 6 M NaOD in HDO:D(2)O. The acceleration of the decay is assigned to fluctuations in the energy levels of the HDO molecules due to charge transfer events and charge fluctuations. The reorientation dynamics of water molecules outside the first hydration shell are observed to show the same time constant of 2.5 ± 0.2 ps as in bulk liquid water, indicating that there is no long range effect of the hydroxide ion on the hydrogen-bond structure of liquid water. The terahertz dielectric relaxation experiments show that the transfer of the hydroxide ion through liquid water involves the simultaneous motion of ~7 surrounding water molecules, considerably less than previously reported for the proton. © 2011 American Institute of Physics

  14. Self-aggregation of liquids from biomass in aqueous solution

    International Nuclear Information System (INIS)

    Lomba, Laura; Giner, Beatriz; Zuriaga, Estefanía; Moya, Juana; Lafuente, Carlos

    2013-01-01

    Highlights: • Aggregation behaviour of liquids from biomass in aqueous solution has been studied. • Standard Gibbs free energies of aggregation have been calculated. • Solubility in water of these compounds has been determined. • Critical aggregation concentration decreases as the solubility in water does. -- Abstract: Aggregation of several chemicals from biomass: furfural derived compounds (furfural, 5-methylfurfural, furfuryl alcohol and tetrahydrofurfuryl alcohol), lactate derived compounds (methyl lactate, ethyl lactate and butyl lactate), acrylate derived compound (methyl acrylate) and levulinate compounds (methyl levulinate, ethyl levulinate and butyl levulinate) in aqueous solution has been characterised at T = 298.15 K through density, ρ, speed of sound, u, and isentropic compressibilities, κ S , measurements. In addition the standard Gibbs free energies of aggregation have been also calculated. Furthermore, in order to deepen insight the behaviour of these chemicals in aqueous solution, the solubility of these compounds has been measured at T = 298.15 K

  15. Study of free acidity determinations in aqueous solution

    International Nuclear Information System (INIS)

    Kergreis, A.

    1966-04-01

    The object of this work is the study of the principal methods which can be applied to the measurement of 'free' acidity. In the first part, we define the various types of acidity which can exist in aqueous solution; then, after having studied some hydrolysis reactions, we compare the value of the neutralisation pH of the hydrated cation and that of the precipitation of the hydroxide. In the second part we have started to study the determination of the acidity of an aqueous solution. After having rapidly considered the 'total' acidity determination, we deal with the problem of the 'free' acidity titration. We have considered in particular certain methods: extrapolation of the equivalent point, colorimetric titrations with or without a complexing agent, and finally the use of ion-exchange resins with mixed aqueous and solvent solutions. (author) [fr

  16. Decomposition kinetics of aminoborane in aqueous solutions

    International Nuclear Information System (INIS)

    Shvets, I.B.; Erusalimchik, I.G.

    1984-01-01

    Kinetics of aminoborane hydrolysis has been studied using the method of polarization galvanostatical curves on a platinum electrode in buffer solutions at pH 3; 5; 7. The supposition that the reaction of aminoborane hydrolysis is the reaction of the first order by aminoborane is proved. The rate constant of aminoborane decomposition in the solution with pH 5 is equal to: K=2.5x10 -5 s -1 and with pH 3 it equals K=1.12x10 -4 s -1

  17. Photodegradation of emamectin benzoate in aqueous solutions

    International Nuclear Information System (INIS)

    Mushtaq, M.; Chukwudebe, A.C.; Wrzesinski, C.; Allen, L.R.S.; Luffer-Atlas, D.; Arison, B.H.

    1998-01-01

    The half-life of [ 14 C]4'-deoxy-4'-(epi-methylamino)avermectin B1a (MAB1a) benzoate (1 ppm) photodegradation in buffer (pH 7), natural pond water, and sensitized buffer (1% acetone in pH 7 buffer) determined at Three Bridges, NJ (latitude approximately 40 degrees N) during the fall season under natural sunlight was 22, 7, and 1 days, respectively. The half-life of [ 14 C]MAB1a benzoate (10-12 ppm) photodegradation in buffer (pH 7) containing 1% (v/v) acetonitrile, ethanol, or acetone as cosolvent under continuous exposure with a xenon lamp was 64.5, 8.5, or 0.5 days, respectively. The photoisomer 8,9-Z-MAB1a, 8a-hydroxy-MAB1a, and unknown polar residues were found in light-exposed samples of MAB1a in buffer and natural pond water. In light-exposed sensitized buffer samples, 8a-oxo-MAB1a and MAB1a-10,11-14,15-diepoxide were additional products. Very polar residues found in the organic and aqueous phases after extraction increased with time, and their formation followed the order sensitized buffer natural pond water buffer. (author)

  18. Photochemical properties of Ysub(t) base in aqueous solution

    International Nuclear Information System (INIS)

    Paszyc, S.; Rafalska, M.

    1979-01-01

    Photoreactivity of Ysub(t) base (I) has been studied in aqueous solution (pH-6) saturated with oxygen. Two photoproducts (II,III), resulting from irradiation at lambda = 253.7 nm and lambda >= 290 nm were isolated and their structures determined. The quantum yield for Ysub(t) base disappearance (rho dis) is 0.002 (lambda = 313 nm). It was shown that dye- sensitised photo-oxidation of Ysub(t) base in aqueous solution occurs according to a Type I mechanism as well as with participation of singlet state oxygen. Quantum yields, fluorescence decay times and phosphorescence of Ysub(t) base have also been determined. (author)

  19. Predicting accurate absolute binding energies in aqueous solution

    DEFF Research Database (Denmark)

    Jensen, Jan Halborg

    2015-01-01

    Recent predictions of absolute binding free energies of host-guest complexes in aqueous solution using electronic structure theory have been encouraging for some systems, while other systems remain problematic. In this paper I summarize some of the many factors that could easily contribute 1-3 kcal......-represented by continuum models. While I focus on binding free energies in aqueous solution the approach also applies (with minor adjustments) to any free energy difference such as conformational or reaction free energy differences or activation free energies in any solvent....

  20. Radiation chemistry of aqueous solutions of acetonitrile and propionitrile

    International Nuclear Information System (INIS)

    Shushtarian, M.J.

    1975-01-01

    The radiation chemistry of water and aqueous solutions is a branch of radiation chemistry dealing with chemical changes in water and aqueous solutions induced by high energy radiations. High energy radiations of interest in radiation chemistry are short-wave electromagnetic radiations (X- and γ-rays) and fast charged particles (α- and β-particles, electrons, deuterons and fission fragments). The energy of the particles and photons bringing about chemical reactions in the field of modern radiation chemistry is much higher than that of photons causing photochemical reactions

  1. Removal of Phenol in Aqueous Solution Using Kaolin Mineral Clay

    International Nuclear Information System (INIS)

    Sayed, M.S.

    2008-01-01

    Kaolin clay were tested for phenol removal as toxic liquid waste from aqueous waste water. Several experimental conditions such as weight and particle size of clay were investigated to study batch kinetic techniques, also the ph and concentration of the phenol solution were carried out. The stability of the Langmuir adsorption model of the equilibrium data were studied for phenol sorbent clay system. Infrared spectra, thermogravimetric and differential thermal analysis techniques were used to characterize the behavior of kaolin clay and kaolin clay saturated with phenol. The results obtained showed that kaolin clay could be used successfully as an efficient sorbent material to remove phenol from aqueous solution

  2. Antimony removal from aqueous solutions using Zirconium hydroxide

    International Nuclear Information System (INIS)

    Petrescu, D.; Velciu, L.; Bucur, C.

    2016-01-01

    In this paper it is presented an experimental test for non-radioactive antimony removal from aqueous solutions using zirconium hydroxide powder. Also, it was studied how the temperature and pH influences antimony adsorption onto zirconium hydroxide surface. After the adsorption, solutions were filtered on Cellulose Mixed Ester Membrane with 0.2 μm pore size to remove the zirconium powder and then the aqueous solutions were sent to Inductively Coupled Plasma Optic Emission Spectrometry (ICP-OES) for quantitative analysis of Sb. Zirconium hydroxide powders were examined by optical microscopy. For the solutions that were tested at pH 4.5 and 10.2 the antimony concentration dropped below the detection limit of ICP-OES device, proof of antimony adsorption on zirconium hydroxide. Also, for the other tested solutions which had pH=12 the antimony concentration reduced with 77% and 80%. The temperature had no influence upon adsorption mechanism. (authors)

  3. Synthesis of C{sub 60}(OH){sub 18-20} in aqueous alkaline solution under O{sub 2}-atmosphere

    Energy Technology Data Exchange (ETDEWEB)

    Alves, Gustavo Catao; Ladeira, Luiz Orlando; Righi, Ariete; Krambrock, Klaus; Pinheiro, Mauricio Veloso B. [Minas Gerais Univ., Belo Horizonte, MG (Brazil). Dept. de Fisica; Calado, Hallen Daniel; Gil, Rossimiriam Pereira de Freitas [Minas Gerais Univ., Belo Horizonte, MG (Brazil). Dept. de Quimica]. E-mail: gustavo.catao@terra.com.br

    2006-09-15

    In this work we report on an alternative synthesis of water-soluble fullerenes known as fullerols, aiming for biomedical applications. The synthesis is based on a process in which polyethylene glycol (PEG400) is used as phase-transfer catalyst between fullerene/benzene and aqueous NaOH solutions. The polyhydroxylation of the fullerenes occurs in the NaOH solution under a continuous flow of O{sub 2} to enhance the reaction yield. The resulting compound was characterized with infrared spectroscopy, nuclear magnetic resonance, thermo-gravimetric analysis and optical absorption. The formation of C{sub 60}(OH){sub 18-20} in high yields was confirmed. (author)

  4. Glasslike behavior in aqueous electrolyte solutions.

    Science.gov (United States)

    Turton, David A; Hunger, Johannes; Hefter, Glenn; Buchner, Richard; Wynne, Klaas

    2008-04-28

    When salts are added to water, generally the viscosity increases, suggesting that the ions increase the strength of the water's hydrogen-bond network. However, infrared pump-probe measurements on electrolyte solutions have found that ions have no influence on the rotational dynamics of water molecules, implying no enhancement or breakdown of the hydrogen-bond network. Here, we report optical Kerr effect and dielectric relaxation spectroscopic measurements, which have enabled us to separate the effects of rotational and transitional motions of the water molecules. These data show that electrolyte solutions behave like a supercooled liquid approaching a glass transition in which rotational and translational molecular motions are decoupled. It is now possible to understand previously conflicting viscosity data, nuclear magnetic resonance relaxation, and ultrafast infrared spectroscopy in a single unified picture.

  5. Contact nuclei formation in aqueous dextrose solutions

    Science.gov (United States)

    Cerreta, Michael K.; Berglund, Kris A.

    1990-06-01

    A laser Raman microprobe was used in situ to observe the growth of alpha dextrose monohydrate on alpha anhydrous dextrose crystals. The Raman spectra indicate growth of the monohydrate below 28.1°C, but the presence of only the anhydrous form above 40.5°C. Contact nucleation experiments with parent anhydrous crystals yielded only monohydrate nuclei below 28.1°C, while contacts in solutions between 34.5 and 41.0°C produced both crystalline forms, and contacts in solutions above 43.5°C produced only anhydrous nuclei. The inability of the monohydrate to grow on anhydrous crystals in the same solution that forms the two crystalline phases with a single contact precludes a simple attrition mechanism of nuclei formation. For the same reason, the hypothetical mechanism involving parent crystal stabilization of pre-crystalline clusters, allowing the clusters to grow into nuclei, is also contradicted. A third, mechanism, which may be a combination of the two, is believed to apply.

  6. Equilibrium studies on aqueous polyvanadate solutions

    International Nuclear Information System (INIS)

    Tytko, K.H.; Mehmke, J.

    1983-01-01

    A reaction scheme for the hydrolysis of the vanadate ion VO 4 3 - in aqueous media derived from theoretical investigations on the formation mechanisms and structures of polymetalate ions has been tested by means of the potentiometric data (z, log c/sub OH - /, C/sub V(V)/) for the polyvanadate system given by Ingri and Brito. Whereas the set of species proposed by these authors only produced an agreement factor σ/sub Z/ = 0.0091, our model realizes σ/sub Z/ = 0.0071 at a level of the random errors of σ/sub Z/ = 0.0064 and leads to a rather more well-balanced deviation diagram δZ(Z). We thus see for the first time a self-contained and detailed picture of the polyvanadate system free of contradictions: The monomeric, tetrahedral vanadate ions polymerize on protonation at first forming an unbroken sequence of chains of VO 4 tetrahedra sharing corners as far as ring closure of the chains, mainly formation of the tetrameric ring, is possible. The driving forces for polymerization are the condensation of water molecules (an entropy effect) and the formation of π-bonds in the V-O-V bridges (strengthening of the bondings), both of them reaching a maximum in rings. The smallest possible, the trimeric ring does not occur because of unfavourable (to small) angles in the V-O-V bridges; the pentameric ring is handicapped for statistical reasons (meeting of the ends of the chain, law of mass action and others). All the species occur according to their basicity as determined mainly by the charge number and by the number of the terminal oxygen atoms in unprotonated, mono- and diprotonated form (chains) or only in unprotonated form (rings). On stronger protonation, as is well known, the V 10 O 28 6 - ion and its protonated forms as well as the VO 2+ ion composed of VO 6 octahedra appear. (author)

  7. Preliminary study on lithium-salt aqueous solution blanket

    International Nuclear Information System (INIS)

    Yoshida, Hiroshi; Naruse, Yuji; Yamaoka, Mitsuaki; Ohara, Atsushi; Ono, Kiyoshi; Kobayashi, Shigetada.

    1992-06-01

    Aqueous solution blanket using lithium salts such as LiNO 3 and LiOH have been studied in the US-TIBER program and ITER conceptual design activity. In the JAERI/LANL collaboration program for the joint operation of TSTA (Tritium Systems Test Assembly), preliminary design work of blanket tritium system for lithium ceramic blanket, aqueous solution blanket and liquid metal blanket, have been performed to investigate technical feasibility of tritium demonstration tests using the TSTA. Detail study of the aqueous solution blanket concept have not been performed in the Japanese fusion program, so that this study was carried out to investigate features of its concept and to evaluated its technical problems. The following are the major items studied in the present work: (i) Neutronics of tritium breeding ratio and shielding performance Lithium concentration, Li-60 enrichment, beryllium or lead, composition of structural material/beryllium/solution, heavy water, different lithium-salts (ii) Physicochemical properties of salts Solubility, corrosion characteristics and compatibility with structural materials, radiolysis (iii) Estimation of radiolysis in ITER aqueous solution blanket. (author)

  8. Chemical denitration of aqueous nitrate solutions

    International Nuclear Information System (INIS)

    Burrill, K.A.

    1987-11-01

    The Plant for Active Waste Liquids (PAWL) at CRNL will immobilize in glass the fission products in waste from Mo-99 production. The nitrate ions in the waste can be destroyed by heating, but also by chemical reaction with formic acid (HCOOH). Since chemical denitration has several advantages over thermal denitration it was studied in the course of vitrification process development. Two free radical mechanisms are examined here to explain kinetic data on chemical denitration of nitric acid solutions with formic acid. One mechanism is applicable at > 1 mol/L HNO 3 and involves the formate radical (HCOO . ). The second mechanism holds at 3 and involves the hyponitrous radical (HNO . ). Mass balances for various species were written based on the law of mass action applied to the equations describing the reaction mechanism. Analytical and numerical solutions were obtained and compared. Literature data on batch denitration were used to determine some of the rate constants while others were set arbitrarily. Observed stoichiometry and trends in reactant concentrations are predicted accurately for batch data. There are no literature data to compare with the prediction of negligible induction time

  9. γ-radiation induced tetracycline removal in an aqueous solution

    International Nuclear Information System (INIS)

    Zhou Fei; Guo Zhaobing; Zhang Chaozhi; Lin Mingyue; Wu Menglong; Zhao Yongfu

    2012-01-01

    Degradation effect of tetracycline (TC) by γ-radiation was investigated in an aqueous solution. The effects of initial concentrations of TC, pH values, combining with H 2 O 2 or CH 3 OH on degradation of TC were studied. Results showed that TC can be effectively degradated by γ-irradiation in an aqueous solution. Degradation of TC could be remarkably improved both in acid solution and alkaline solution, especially when pH value was 9.0. In addition, H 2 O 2 could gently promote degradation of TC induced by γ-radiation. While, CH 3 OH markedly restrained degradation of TC induced by γ-radiation. The degradation mechanism of TC was supposed by results of quantum chemical calculations and LC-MS. Results proved that degradation of TC induced by γ-radiation was mainly ascribed to · OH oxidation. (authors)

  10. Radiolysis of paracetamol in dilute aqueous solution

    Science.gov (United States)

    Szabó, László; Tóth, Tünde; Homlok, Renáta; Takács, Erzsébet; Wojnárovits, László

    2012-09-01

    Using radiolytic experiments hydroxyl radical (main reactant in advanced oxidation processes) was shown to effectively destroy paracetamol molecules. The basic reaction is attachment to the ring. The hydroxy-cyclohexadienyl radical produced in the further reactions may transform to hydroxylated paracetamol derivatives or to quinone type molecules and acetamide. The initial efficiency of aromatic ring destruction in the absence of dissolved O2 is c.a. 10%. The efficiency is 2-3 times higher in the presence of O2 due to its reaction with intermediate hydroxy-cyclohexadienyl radical and the subsequent ring destruction reactions through peroxi radical. Upon irradiation the toxicity of solutions at low doses increases with the dose and then at higher doses it decreases. This is due to formation of compounds with higher toxicity than paracetamol (e.g. acetamide, hidroquinone). These products, however, are highly sensitive to irradiation and degrade easily.

  11. Heterogeneous primary nucleation of ice in water and aqueous solutions

    NARCIS (Netherlands)

    Thijssen, H.A.C.; Vorstman, M.A.G.; Roels, J.A.

    1968-01-01

    The effect of the volume of the liquid sample, the degree of turbulence in the liquid, and the rate of cooling upon the probability of nucleation has been studied for water and aqueous solutions. Nucleation rates were measured for droplets nearly instantaneously cooled to a predetermined

  12. The coacervation of aqueous solutions of tetraalkylammonium halides

    International Nuclear Information System (INIS)

    Mugnier de Trobriand, Anne.

    1979-09-01

    The coacervation of aqueous solutions of tatraalkylammonium halides in the presence of not of inorganic halides and acids has been studied, considering thermodynamic and spectroscopic aspects. The importance of dispersion forces as well as forces resulting from hydrophobic hydration has been assessed. The analogy between these systems and anionic ion exchange resins has been shown especially for Uranium VI extraction [fr

  13. Ion from Aqueous Solution using Magnetite, Activated Carbon

    African Journals Online (AJOL)

    ADOWIE PERE

    Thermodynamic studies on Adsorption of lead (II) Ion from Aqueous Solution using. Magnetite ... process industries and agricultural activities, which tends to ... osmosis. These processes are however, not economically feasible for small scale industries .... Freundlich coefficient. ..... from binary component system, Beni-suef.

  14. from an aqueous solution using Azadirachta indica leaf powder

    African Journals Online (AJOL)

    Azadirachta indica (neem) leaf powder was used as an adsorbent for the removal of textile dye from aqueous solution. The adsorption of dye on A. indica was found to be dependent on contact time, dye concentration and amount of adsorbent. Spectrophotometric technique was used for the measurement of concentration of ...

  15. Removal of phosphate and nitrate from aqueous solution using ...

    African Journals Online (AJOL)

    The aim of the present study was the removal of phosphate and nitrate by sodium alginate seagrass (Cymodocea rotundata) beads from aqueous solutions. The adsorption characteristics of phosphate and nitrate on the seagrass beads were optimized under different operational parameters like adsorbent dosage, initial ...

  16. Adsorption of methylene blue from aqueous solution on the surface ...

    African Journals Online (AJOL)

    Adsorption of dye methylene blue from aqueous solution on the surface of sheep wool and cotton fibers was accomplished under the optimize conditions of temperature, concentration, pH, stay time duration and quantity of adsorbent. Spectrometric technique was used for the measurements of concentration of dye before ...

  17. Removal of Hexavalent Chromium from Aqueous Solutions using ...

    African Journals Online (AJOL)

    The hexavalent chromium exists in aquatic media as water soluble complex anions and persist. These are concentrated in industrial waste water especially from the tannery industries and release of effluents from industries adversely affects the environment. The removal of heavy metals from aqueous solutions is carried ...

  18. The biosorption of cadmium and lead ions from aqueous Solution ...

    African Journals Online (AJOL)

    The biosorption potentiality of Musa paradisiaca stalk at removing cadmium and lead ions from aqueous solution was investigated. The biosorption experiment was carried out as a function of contact time, initial pH, initial metal ion concentration and biosorbent dose. Adsorption equilibria were obtained from batch ...

  19. Biosorptive removal of cobalt (II) ions from aqueous solution by ...

    African Journals Online (AJOL)

    The objective of this study was to investigate the possibility of using Amaranthus hybridus L. stalk as an alternative to high cost commercial adsorbent materials for the removal of Co (II) from aqueous solution. The experiment was carried out by batch method at 33°C. The influence of pH, contact time and initial metal ion ...

  20. Pulse radiolysis of pyridine and methylpyridines in aqueous solutions

    DEFF Research Database (Denmark)

    Solar, S.; Getoff, N.; Sehested, K.

    1993-01-01

    The radicals formed from pyridine, 3-methylpyridine, 3,5-dimethylpyridine, 2,6-dimethylpyridine and 2,4,6-trimethylpyridine by attack of H, e(aq)-, OH and O.- in aqueous solutions were investigated by pulse radiolysis in the pH-range 1-13.8. The UV-vis. absorption spectra as well as the formation...

  1. Removal of phosphate and nitrate from aqueous solution using ...

    African Journals Online (AJOL)

    sunny t

    water, 3.5 g of NaCl were dissolved to obtain 3.5 g/l salinity final solution. When the ... The nitrate adsorption was highly pH dependent, which affects the ... adsorption mechanism that the optimum pH for phosphate removal by .... Biosorption of copper(ii) from aqueous ... Accumulation and detoxification of toxic elements by ...

  2. NMR study of thermoresponsive block copolymer in aqueous solution

    Czech Academy of Sciences Publication Activity Database

    Spěváček, Jiří; Konefal, Rafal; Čadová, Eva

    2016-01-01

    Roč. 217, č. 12 (2016), s. 1370-1375 ISSN 1022-1352 R&D Projects: GA ČR(CZ) GA15-13853S Institutional support: RVO:61389013 Keywords : aqueous solutions * NMR * NOESY Subject RIV: CD - Macromolecular Chemistry Impact factor: 2.500, year: 2016

  3. DETERMINATION OF CHLORHEXIDINE IN SALIVA AND IN AQUEOUS-SOLUTIONS

    NARCIS (Netherlands)

    de Vries, J.; Ruben, J; Arends, J.

    1991-01-01

    A new method is presented for the determination of chlorhexidine in centrifuged saliva and in aqueous solutions by means of fluorescence spectroscopy. The method relies on complex formation between chlorhexidine and eosin. The fluorescence value of the chlorhexidine-eosin system decreases with

  4. Degradation of Para-Phenylenediamine in Aqueous Solution by ...

    African Journals Online (AJOL)

    In this research Photo-Fenton Oxidation of Para-Phenylenediamine (PPD) in aqueous solution by UV/Fenton's reagent (Fe2+ and H2O2) was investigated. ... lower concentration of Phenylenediamines and UV-C assisted photo-Fenton showed that the photo-Fenton process was very effective than the normal Fenton process ...

  5. Equilibrium Sorption Studies of Hg (II) Ions from Aqueous Solution ...

    African Journals Online (AJOL)

    The potential of swamp arum (Lasimorpha senegalensis) seeds as a low-cost adsorbent for the removal of Hg (II) ions from aqueous solution was investigated in this study. The influence of initial metal concentration on the percent adsorption of Hg (II) ions onto powdered swamp arum seeds was studied in a batch system ...

  6. Kinetics of absorption of carbon dioxide in aqueous ammonia solutions

    NARCIS (Netherlands)

    Derks, P. W. J.; Versteeg, G. F.

    2009-01-01

    In the present work the absorption of carbon dioxide into aqueous ammonia solutions has been studied in a stirred cell reactor, at low temperatures and ammonia concentrations ranging from 0.1 to about 7 kmol m-3. The absorption experiments were carried out at conditions where the so-called pseudo

  7. Transitions in aqueous solutions of sucrose at subzero temperatures

    Czech Academy of Sciences Publication Activity Database

    Sikora, Antonín; Dupanov, V. O.; Kratochvíl, Jaroslav; Zámečník, J.

    2007-01-01

    Roč. 46, č. 1 (2007), s. 71-85 ISSN 0022-2348 R&D Projects: GA ČR(CZ) GA522/04/0384 Institutional research plan: CEZ:AV0Z40500505 Keywords : aqueous sucrose solutions * subzero temperature * glass transitions Subject RIV: BJ - Thermodynamics Impact factor: 0.809, year: 2007

  8. Densities concentrations of aqueous of uranyl nitrate solutions

    International Nuclear Information System (INIS)

    Rodrigo Otero, A.; Rodriguez Hernandez, B.; Fernandez Rodriguez, L.

    1966-01-01

    The ratio density-concentration of aqueous uranyl nitrate solutions expressed as U 3 O 8 grams/liter, U grams/liter and hexahydrate uranyl nitrate weight percent at different temperatures, are established. Experimental values are graphically correlated and compared whit some published data. (Author) 2 refs

  9. Accurate Description of Calcium Solvation in Concentrated Aqueous Solutions

    Czech Academy of Sciences Publication Activity Database

    Kohagen, Miriam; Mason, Philip E.; Jungwirth, Pavel

    2014-01-01

    Roč. 118, č. 28 (2014), s. 7902-7909 ISSN 1520-6106 R&D Projects: GA ČR GBP208/12/G016; GA MŠk LH12001 Institutional support: RVO:61388963 Keywords : calcium chloride * aqueous solution * molecular dynamics * neutron scattering Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 3.302, year: 2014

  10. Arsenic (III Adsorption Using Palladium Nanoparticles from Aqueous Solution

    Directory of Open Access Journals (Sweden)

    Farzaneh Arsiya

    2017-07-01

    Full Text Available The presence of Arsenic in drinking water is the greatest threat to health effects especially in water. The purpose of this study is application of green palladium nanoparticles for removal of trivalent Arsenic from aqueous solutions and also the impact of some factors such as retention time, pH, concentration of palladium nanoparticles and Arsenic concentrations was studied. The values for Arsenic removal from aqueous solutions were measured by furnace atomic adsorption spectrometry (Conter AA700. In the study, Langmuir and Freundlich isotherm models and pseudo-second order kinetic model were studied. The results of  optimization is shown that 0.5 g of nanoparticles can removed %99.8 of Arsenic with initial concentration of  0.5 g/l, in 5 minutes at pH=4. Langmuir model, Freundlich model (R2=0.94 and pseudo-second order kinetic model (R2=0.99 shown high correlation for removing of Arsenic from aqueous solutions. It was found, palladium nanoparticles can be used as an efficient method to remove Arsenic from aqueous solutions in a short time.

  11. Analysis and modeling of alkali halide aqueous solutions

    DEFF Research Database (Denmark)

    Kim, Sun Hyung; Anantpinijwatna, Amata; Kang, Jeong Won

    2016-01-01

    on calculations for various electrolyte properties of alkali halide aqueous solutions such as mean ionic activity coefficients, osmotic coefficients, and salt solubilities. The model covers highly nonideal electrolyte systems such as lithium chloride, lithium bromide and lithium iodide, that is, systems...

  12. Examination of rheological properties of aqueous solutions of sodium caseinate

    OpenAIRE

    Jolanta Gawałek; Piotr Wesołowski

    2012-01-01

    Application of sodium caseinate as a functional additive in manufacturing processes requires production of its concentrated aqueous solutions which, in industrial conditions, presents a number of difficulties. In order to develop an effective and optimal industrial process of mixing – manufacturing a concentrated solution of sodium caseinate, it is essential to know rheological properties in a definite range of concentrations changing in the course of the dissolving process. The materia...

  13. Assembly of DNA Architectures in a Non-Aqueous Solution

    Directory of Open Access Journals (Sweden)

    Thomas J. Proctor

    2012-08-01

    Full Text Available In the present work, the procedures for the creation of self-assembled DNA nanostructures in aqueous and non-aqueous media are described. DNA-Surfactant complex formation renders the DNA soluble in organic solvents offering an exciting way to bridge the transition of DNA origami materials electronics applications. The DNA retains its structural features, and these unique geometries provide an interesting candidate for future electronics and nanofabrication applications with potential for new properties. The DNA architectures were first assembled under aqueous conditions, and then characterized in solution (using circular dichroism (CD spectroscopy and on the surface (using atomic force microscopy (AFM. Following aqueous assembly, the DNA nanostructures were transitioned to a non-aqueous environment, where butanol was chosen for optical compatibility and thermal properties. The retention of DNA hierarchical structure and thermal stability in non-aqueous conditions were confirmed via CD spectroscopy. The formation and characterization of these higher order DNA-surfactant complexes is described in this paper.

  14. Electrostatic interactions in aqueous solutions of polyelectrolyte

    International Nuclear Information System (INIS)

    Belloni, Luc

    1982-01-01

    In this study, the structure, equilibrium and transport properties of poly-electrolytes solutions are reported. These dissymmetric systems are studied in the context of a primitive model (Charged hard spheres and rods in a solvent continuum). The first phenomenon studied is the strong electrostatic attractive interaction of counterions on the poly-ion surface. The model used considers the poly-ions on a matrix and the different concentrations are calculated using the P.B. equation. Auto-diffusion coefficients obtained give a good description of experimental slowing down of the counterions. The model allows a correlation between the theoretical limits represented by Bjerrum's and Manning's models and gives a physical significance to the concept of condensation. In the second part, the complete structure is calculated using only slightly restrictive H.N.C. approximation. This theory enables all the pair correlation functions to be calculated as well as thermodynamic data and structure factors. The last part of this study treats transport phenomena. Quasi-elastic light scattering gives information on the autocorrelation function of the scattered light intensity. Analysis using cumulants leads to an effective diffusion coefficient which is theoretically related to the structure factor and the hydrodynamic interactions. A crude approximation of the last contribution allows to fit the experimental data. (author) [fr

  15. Block copolymer membranes for aqueous solution applications

    KAUST Repository

    Nunes, Suzana Pereira

    2016-03-22

    Block copolymers are known for their intricate morphology. We review the state of the art of block copolymer membranes and discuss perspectives in this field. The main focus is on pore morphology tuning with a short introduction on non-porous membranes. The two main strategies for pore formation in block copolymer membranes are (i) film casting and selective block sacrifice and (ii) self-assembly and non-solvent induced phase separation (SNIPS). Different fundamental aspects involved in the manufacture of block copolymer membranes are considered, including factors affecting the equilibrium morphology in solid films, self-assembly of copolymer in solutions and macrophase separation by solvent-non-solvent exchange. Different mechanisms are proposed for different depths of the SNIPS membrane. Block copolymer membranes can be prepared with much narrower pore size distribution than homopolymer membranes. Open questions and indications of what we consider the next development steps are finally discussed. They include the synthesis and application of new copolymers and specific functionalization, adding characteristics to respond to stimuli and chemical environment, polymerization-induced phase separation, and the manufacture of organic-inorganic hybrids.

  16. Phytoremediation of Heavy Metals in Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    Felix Aibuedefe AISIEN

    2010-12-01

    Full Text Available One of the major environmental problems is the pollution of water and soil by toxic heavy metals. This study investigated the phytoremediation potential of water hyacinth, for the removal of cadmium (Cd, lead (Pb and zinc (Zn. Water hyacinths were cultured in bore-hole water, supplemented with 5mg/l of Zn and Pb and 1mg/l of Cd at pH 4.5, 6.8 and 8.5. The plants were separately harvested each week for six weeks. The results showed that removal of these metals from solution was fast especially in the first two weeks, after which it became gradual till saturation point was reached. The accumulation of Cd and Zn in leaves and roots increased with increase in pH. The highest accumulation was in the roots with metal concentration of 4870mg/kg, 4150mg/kg and 710mg/kg for Zn, Pb and Cd respectively at pH 8.5. The maximum values of bioconcentration factor (BCF for Zn, Pb and Cd were 1674, 1531 and 1479 respectively, suggesting that water hyacinth was good accumulator of Zn, Pb and Cd, and could be used to treat industrial wastewater contaminated with heavy metals such as Zn, Pb and Cd.

  17. Protein aggregation in aqueous casein solution

    International Nuclear Information System (INIS)

    Yousri, R.M.

    1980-01-01

    From the vast amount of research efforts dealing with various aspects of radiation effects on foods and food components (11, 18, 5, 12, 19, 8, 9, 6, 13, 15, 17, 20), it is apparent up to now that much remains to be studied in depth, much may have to be added or corrected about radiation-induced physico-chemical changes in foods. A great many reactions that take place when foodstuffs are subjected to ionizing radiation are still not fully understood. The better understanding of some of the radiation-induced changes in pure proteins as such or in mixture with other food constituents could yield much data which could be meaningfully extrapolated to intact foods and consequently could help to improve the assessment of the wholesomeness of irradiated foods. It was the purpose of our investigations to elucidate some of the changes in the chemical structure of a pure protein (casein), irradiated as such or which added carbohydrate and/or lipid. The effect of subsequent storage of the irradiated solutions has been also examined. The formation of protein aggregates was studied by gel filtration technique. The application of thin-layer gel filtration, its speed and adaptability to very small samples facilitated the measurements of the extent of aggregation which occurred in protein molecules after irradiation. (orig.) [de

  18. Block copolymer membranes for aqueous solution applications

    KAUST Repository

    Nunes, Suzana Pereira

    2016-01-01

    Block copolymers are known for their intricate morphology. We review the state of the art of block copolymer membranes and discuss perspectives in this field. The main focus is on pore morphology tuning with a short introduction on non-porous membranes. The two main strategies for pore formation in block copolymer membranes are (i) film casting and selective block sacrifice and (ii) self-assembly and non-solvent induced phase separation (SNIPS). Different fundamental aspects involved in the manufacture of block copolymer membranes are considered, including factors affecting the equilibrium morphology in solid films, self-assembly of copolymer in solutions and macrophase separation by solvent-non-solvent exchange. Different mechanisms are proposed for different depths of the SNIPS membrane. Block copolymer membranes can be prepared with much narrower pore size distribution than homopolymer membranes. Open questions and indications of what we consider the next development steps are finally discussed. They include the synthesis and application of new copolymers and specific functionalization, adding characteristics to respond to stimuli and chemical environment, polymerization-induced phase separation, and the manufacture of organic-inorganic hybrids.

  19. AUSTRALIAN PINE CONES-BASED ACTIVATED CARBON FOR ADSORPTION OF COPPER IN AQUEOUS SOLUTION

    Directory of Open Access Journals (Sweden)

    MUSLIM A.

    2017-02-01

    Full Text Available The Australian Pine cones (APCs was utilised as adsorbent material by physical and chemical activation for the adsorption Cu(II in aqueous solution. FTIR and SEM analysis were conducted to obtain the active site and to characterise the surface morphology of the APCs activated carbon (APCs AC prepared through pyrolysis at 1073.15 K and alkaline activation of NaOH. The independent variables effect such as contact time, Cu(II initial concentration and the activator ratio in the ranges of 0-150 min, 84.88-370.21 mg/l and 0.2-0.6 (NaOH:APCs AC, respectively on the Cu(II adsorption capacity were investigated in the APCs activated carbon-solution (APCs ACS system with 1 g the APCs AC in 100 mL Cu(II aqueous solution with magnetic stirring at 75 rpm, room temperature of 298.15 K (± 2 K, 1 atm and pH 5 (±0.25. As the results, Cu(II adsorption capacity dramatically increased with increasing contact time and Cu(II initial concentration. The optimal Cu(II adsorption capacity of 26.71 mg/g was obtained in the APCs ACS system with 120-min contact time, 340.81 m/l initial Cu(II and 0.6 activator ratio. The kinetics study showed the Cu(II adsorption kinetics followed the pseudo-second-order kinetics with 27.03 mg/g of adsorption capacity, 0.09 g/mg.min of rate constant and 0.985-R2. In addition, the Cu(II adsorption isotherm followed the Langmuir model with 12.82 mg/g of the mono-layer adsorption capacity, 42.93 l/g of the over-all adsorption capacity and 0.954-R2.

  20. Experimental measurements of U60 nanocluster stability in aqueous solution

    Science.gov (United States)

    Flynn, Shannon L.; Szymanowski, Jennifer E. S.; Gao, Yunyi; Liu, Tianbo; Burns, Peter C.; Fein, Jeremy B.

    2015-05-01

    In this study, the aqueous behavior of isolated U60 nanoclusters (K16Li25[UO2(O2)OH]60)-19 was studied under several pH conditions and nanocluster concentrations to determine if the nanoclusters exhibit solid phase buffering behavior or if they exhibit behavior more like aqueous complexes. U60 is a cage cluster consisting of 60 (UO2)(O2)2(OH)2 uranyl polyhedral which share OH and O2 groups with their neighboring uranyl polyhedral, resulting in negatively charged cage clusters whose charge is at least partially offset by K+ and Li+ in the aqueous phase. Batch experiments to monitor nanocluster stability were conducted for 16 days at pH 7.5, 8.0 and 8.5 at nanocluster suspension concentrations of 1.4, 2.8 and 6.0 g/L. The aqueous concentrations of U, Li, and K, determined after 10 kDa molecular weight filtration, achieved steady-state with the nanoclusters within 24 h. The steady-state aqueous U, Li, and K concentrations were independent of solution pH, however they increased with increasing nanocluster concentration, indicating that the nanoclusters do not buffer the aqueous activities as a bulk solid phase would, but exhibit behavior that is more characteristic of dissolved aqueous complexes. The ion activity product (I.A.P.) value was calculated using two approaches: (1) treating the nanoclusters as a solid phase with an activity of one, and (2) treating the nanoclusters as aqueous complexes with a non-unit activity equal to their concentration in solution. The I.A.P. values that were calculated with non-unit activity for the nanoclusters exhibited significantly less variation as a function of nanocluster concentration compared to the I.A.P. values calculated with a nanocluster activity of one. The results yield a calculated log dissociation constant for the U60 nanoclusters of 9.2 + 0.2/-0.3 (1σ). Our findings provide a better understanding of the thermodynamic stability and behavior of U60 nanoclusters in aqueous systems, and can be used to estimate the

  1. Removal of Pb2+ from aqueous solutions by a high-efficiency resin

    International Nuclear Information System (INIS)

    Guo, Hao; Ren, Yongzheng; Sun, Xueliang; Xu, Yadi; Li, Xuemei; Zhang, Tiancheng; Kang, Jianxiong; Liu, Dongqi

    2013-01-01

    The removal of Pb 2+ from aqueous solution by 732 cation-exchange resin in sodium type (732-CR) has been studied in batch experiments at varying pH (2.0–8.0), Pb 2+ concentration (50–200 mg/L), contact time (5–300 min), temperature (288–308 K) and resin dose (0.125–0.75 g/L). The experimental data show that the ion-exchange process was dependent on pH and temperature, the optimal exchange capacity was found at pH 4.0, and higher temperature was beneficial to lead sorption. Kinetic data indicate that the ion-exchange process followed a pseudo-first order model. The equilibrium exchange capacity could be reached at approximately 4 h, and the maximum sorption capacity of Pb 2+ at pH 4.0 was 396.8 mg/g resin. The equilibrium data were evaluated with Langmuir and Freundlich model, and were best fitted with Langmuir model. The thermodynamic parameters for removal of Pb 2+ indicate that the reaction was spontaneous and endothermic. Additionally, column tests were conducted by using both synthetic solution and effluents from lead battery industry. The regeneration of resin was performed for two sorption-regeneration cycles by 1 M NaOH, and the results show that effective regeneration was achieved by this method.

  2. Separation of compounds with multiple -OH groups from dilute aqueous solutions via complexation with organoboronate

    Energy Technology Data Exchange (ETDEWEB)

    Chow, Tina Kuo Fung [Univ. of California, Berkeley, CA (United States)

    1992-05-01

    The complexing extractant agent investigated in this work is 3-nitrophenylboronic acid (NPBA) in its anionic form (NPB). NPBA and Aliquat 336 (quaternary amine) is dissolved in 2-ethyl-l-hexanol, and the extractant is contacted with aq. NaOH. Solutes investigated were 1,2-propanediol, glycerol, fructose, sorbitol and lactic acid. Batch extraction experiments were performed at 25°C. Partition coefficients, distribution ratios and loadings are reported for varying concentrations of solute and NPB. All solutes complexed with NPB-, with all complexes containing only one NPB- per complex. The 1:1 complexation constants for the solutes glycerol, fructose and sorbitol follow trends similar to complexation with B(OH)4- (aq.), i.e. the complexation constants increase with increasing number of -OH groups available for complexation. Assumption of 1:1 complex is not valid for 1, 2-propanediol, which showed overloading (more than one mole of solute complexed to one mole NPB-) at higher concentrations. The -OH group on the NPB- which is left uncomplexed after one solute molecule had bound to the other two -OH groups may be responsible for the overloading. Overloading is also observed in extraction of tactic acid, but through a different mechanism. It was found that TOMA+ can extract lactic acid to an extent comparable to the uptake of lactic acid by NPB-. The complexation is probably through formation of an acid-base ion pair. Losses of NPBA into the aqueous phase could lead to problems, poor economics in industrial separation processes. One way of overcoming this problem would be to incorporate the NPBA onto a solid support.

  3. Radiation resistance of organic azo dyes in aqueous solutions

    International Nuclear Information System (INIS)

    Khabarov, V.N.; Kozlov, L.L.

    1987-01-01

    The resistance to the action of the ionizing radiation of aqueous and aqueous-alcoholic solutions of organic mono- and diazo dyes was studied. The radiation chemical yield of decolorization of the dye, determined from the kinetic decolorization curves served as a quantitative criterion of the radiation resistance. The influence of pH, addition of ethanol, hydroquinone, thiourea, glucose and oxygen on the radiation resistance of the azo dyes was studied. An attempt was made to relate the efficiency of radiation decolorization to the chemical nature of the dye

  4. Degradation of alachlor in aqueous solution by using hydrodynamic cavitation.

    Science.gov (United States)

    Wang, Xikui; Zhang, Yong

    2009-01-15

    The degradation of alachlor aqueous solution by using hydrodynamic cavitation was systematically investigated. It was found that alachlor in aqueous solution can be deomposed with swirling jet-induced cavitation. The degradation can be described by a pseudo-first-order kinetics and the degradation rate was found to be 4.90x10(-2)min(-1). The effects of operating parameters such as fluid pressure, solution temperature, initial concentration of alachlor and medium pH on the degradation rates of alachlor were also discussed. The results showed that the degradation rates of alachlor increased with increasing pressure and decreased with increasing initial concentration. An optimum temperature of 40 degrees C existed for the degradation rate of alachlor and the degradation rate was also found to be slightly depend on medium pH. Many degradation products formed during the process, and some of them were qualitatively identified by GC-MS.

  5. Complex chemistry of Np(V) in aqueous solutions

    International Nuclear Information System (INIS)

    Inoue, Yasushi

    1989-01-01

    Despite the importance of Np(V) in both the nuclear chemical engineering and the actinoid chemistry, little work has been performed on the complex chemistry of Np(V) in aqueous solutions, since Np(V) reacts less readily with various ligands. The author has directed his effort to understand the chemical behavior of Np(V) in aqueous solutions, especially the determination of the stability constants of Np(V) complexes with various ligands. A part of the results obtained so far is presented in the following order. (1) The synergistic extraction of Np(V) as a method for studying the complex chemistry of Np(V): TTA-MTOA(methyltrioctylammonium chloride), TTA-phen and TTA-TOPO. (2) The determination of the stability constants of Np(V) complexes with 22 organic- and 5 inorganic ligands by means of the solvent extraction. (3) The distribution of the chemical species of Np(V) in solutions under various conditions

  6. Molecular mechanism of the viscosity of aqueous glucose solutions

    Science.gov (United States)

    Bulavin, L. A.; Zabashta, Yu. F.; Khlopov, A. M.; Khorol'skii, A. V.

    2017-01-01

    Experimental relations are obtained for the viscosity of aqueous glucose solutions in the temperature range of 10-80°C and concentration range 0.01-2.5%. It is found that the concentration dependence of fluidity is linear when the concentration is higher than a certain value and varies at different temperatures. The existence of such a dependence indicates that the mobilities of solvent and solute molecules are independent of the concentration of solutions. This assumption is used to construct a theoretical model, in which the structure of an aqueous glucose solution is presented as a combination of two weakly interacting networks formed by hydrogen bonds between water molecules and between glucose molecules. Theoretical relations are obtained using this model of network solution structure for the concentration and temperature dependence of solution viscosity. Experimental data are used to calculate the activation energies for water ( U w = 3.0 × 10-20 J) and glucose molecules ( U g = 2.8 × 10-20 J). It is shown that the viscosity of a solution in such a network structure is governed by the Brownian motion of solitons along the chains of hydrogen bonds. The weak interaction between networks results in the contributions to solution fluidity made by the motion of solitons in both of them being almost independent.

  7. A novel rate of the reaction between NaOH with CO2 at low temperature in spray dryer

    Directory of Open Access Journals (Sweden)

    Yadollah Tavan

    2017-03-01

    Full Text Available Carbon dioxide (CO2 is an influential greenhouse gas that has a significant impact on global warming partly. Nowadays, many techniques are available to control and remove CO2 in different chemical processes. Since the spray dryer has high removal efficiency rate, a laboratory-scale spray dryer is used to absorb carbon dioxide from air in aqueous solution of NaOH. In the present study, the impact of NaOH concentration, operating temperature and nozzle diameter on removal efficiency of CO2 is explored through experimental study. Moreover, the reaction kinetic of NaOH with CO2 is studied over the temperature range of 50–100 °C in a laboratory-scale spray dryer absorber. In the present contribution, a simple reaction rate equation is proposed that shows the lowest deviation from the experimental data with error less than 2%.

  8. Unusual radiolytic behavior of neptunium ions in aqueous bicarbonate solutions

    International Nuclear Information System (INIS)

    Shilov, V.P.; Gogolev, A.V.; Pikaev, A.K.

    2000-01-01

    Behavior of neptunium ions in carbonate and bicarbonate aqueous solutions saturated with air, oxygen or argon during gamma radiation ( 60 Co) by doses up to 3 kGy at dose rates 10 and 25 Gy/min was studied by the method of spectrophotometry. It is shown that in neptunium (5) bicarbonate solution nearly complete (95%) neptunium ion oxidation occurs under the effect of radiation, whereas no oxidation is observed in carbonate solution. Radiation-chemical yield of neptunium (5) oxidation and stationary concentration of neptunium (6) ions depend on concentration of bicarbonate-ions. Explanation to the results obtained is made from the viewpoint of potential radiolytic reactions [ru

  9. Adsorption of phosphate from aqueous solutions and sewage using zirconium loaded okara (ZLO): Fixed-bed column study

    International Nuclear Information System (INIS)

    Nguyen, T.A.H.; Ngo, H.H.; Guo, W.S.; Pham, T.Q.; Li, F.M.; Nguyen, T.V.; Bui, X.T.

    2015-01-01

    This study explores the potential of removing phosphorus from aqueous solutions and sewage by Zr(IV)-loaded okara (ZLO) in the fixed-bed column. Soybean residue (okara) was impregnated with 0.25 M Zr(IV) solution to prepare active binding sites for phosphate. The effect of several factors, including flow rate, bed height, initial phosphorus concentration, pH and adsorbent particle size on the performance of ZLO was examined. The maximum dynamic adsorption capacity of ZLO for phosphorus was estimated to be 16.43 mg/g. Breakthrough curve modeling indicated that Adams–Bohart model and Thomas model fitted the experimental data better than Yoon–Nelson model. After treatment with ZLO packed bed column, the effluent could meet the discharge standard for phosphorus in Australia. Successful desorption and regeneration were achieved with 0.2 NaOH and 0.1 HCl, respectively. The results prove that ZLO can be used as a promising phosphorus adsorbent in the dynamic adsorption system. - Highlights: • Dynamic adsorption of P from water and wastewater by Zr(IV)-loaded okara was tested. • Effects of column design parameters on the adsorption performance were investigated. • The dynamic adsorption capacity of Zr(IV)-loaded okara for P was reasonably high. • The spent column was effectively regenerated with 0.2 M NaOH followed by 0.1 M HCl. • Zr(IV)-loaded okara column was efficient in eliminating P from municipal sewage

  10. Adsorption of phosphate from aqueous solutions and sewage using zirconium loaded okara (ZLO): Fixed-bed column study

    Energy Technology Data Exchange (ETDEWEB)

    Nguyen, T.A.H. [Centre for Technology in Water and Wastewater, School of Civil and Environmental Engineering, University of Technology, Sydney (UTS), 15 Broadway, Ultimo, NSW 2007 (Australia); Ngo, H.H., E-mail: ngohuuhao121@gmail.com [Centre for Technology in Water and Wastewater, School of Civil and Environmental Engineering, University of Technology, Sydney (UTS), 15 Broadway, Ultimo, NSW 2007 (Australia); Guo, W.S. [Centre for Technology in Water and Wastewater, School of Civil and Environmental Engineering, University of Technology, Sydney (UTS), 15 Broadway, Ultimo, NSW 2007 (Australia); Pham, T.Q. [Faculty of Geography, University of Science, Vietnam National University, Hanoi (Viet Nam); Li, F.M. [College of Environmental Science and Engineering, Ocean University of China, Qingdao 266100 (China); Nguyen, T.V. [Centre for Technology in Water and Wastewater, School of Civil and Environmental Engineering, University of Technology, Sydney (UTS), 15 Broadway, Ultimo, NSW 2007 (Australia); Bui, X.T. [Environmental Engineering and Management Research Group, Ton Duc Thang University, Ho Chi Minh City (Viet Nam); Faculty of Environment and Natural Resources, Ho Chi Minh City University of Technology-Vietnam National University, Ho Chi Minh City (Viet Nam)

    2015-08-01

    This study explores the potential of removing phosphorus from aqueous solutions and sewage by Zr(IV)-loaded okara (ZLO) in the fixed-bed column. Soybean residue (okara) was impregnated with 0.25 M Zr(IV) solution to prepare active binding sites for phosphate. The effect of several factors, including flow rate, bed height, initial phosphorus concentration, pH and adsorbent particle size on the performance of ZLO was examined. The maximum dynamic adsorption capacity of ZLO for phosphorus was estimated to be 16.43 mg/g. Breakthrough curve modeling indicated that Adams–Bohart model and Thomas model fitted the experimental data better than Yoon–Nelson model. After treatment with ZLO packed bed column, the effluent could meet the discharge standard for phosphorus in Australia. Successful desorption and regeneration were achieved with 0.2 NaOH and 0.1 HCl, respectively. The results prove that ZLO can be used as a promising phosphorus adsorbent in the dynamic adsorption system. - Highlights: • Dynamic adsorption of P from water and wastewater by Zr(IV)-loaded okara was tested. • Effects of column design parameters on the adsorption performance were investigated. • The dynamic adsorption capacity of Zr(IV)-loaded okara for P was reasonably high. • The spent column was effectively regenerated with 0.2 M NaOH followed by 0.1 M HCl. • Zr(IV)-loaded okara column was efficient in eliminating P from municipal sewage.

  11. A novel method of non-violent dissolution of sodium metal in a concentrated aqueous solution of Epsom salt

    International Nuclear Information System (INIS)

    Lakshmanan, A.R.; Prasad, M.V.R.; Ponraju, D.; Krishnan, H.

    2004-01-01

    A new technique of non-violent and fast dissolution of sodium metal in a concentrated aqueous solution of Epsom salt (MgSO 4 .7H 2 O) at room temperature (RT) has been developed. The dissolution process is mildly exothermic but could be carried out even in a glass beaker in air under swift stirring condition. The reaction products consist of mixed salts of MgSO 4 and Na 2 SO 4 as well as Mg(OH) 2 which are only mildly alkaline and hence are non-corrosive and non-hazardous unlike NaOH. A 50 mL solution having Epsom salt concentration of 2 M was found to give the optimal composition for disposal of 1 g of sodium. Supersaturated (>2.7 M), as well as dilute (<1.1 M) solutions, however, cause violent reactions and hence should be avoided. Repeated sodium dissolution in Epsom solution produced a solid waste of 4.7 g per g of sodium dissolved which is comparable with the waste (4 g) produced in 8 M NaOH solution. A 1.4 M Epsom solution sprayed with a high-pressure jet cleaner at RT in air easily removed the sodium blocked inside a metal pipe made of mild steel. The above jet also dissolved peacefully residual sodium collected on the metal tray after a sodium fire experiment. No sodium fire or explosion was observed during this campaign. The Epsom solution spray effectively neutralized the minor quantity of sodium aerosol produced during this campaign. This novel technique would hence be quite useful for draining sodium from fast breeder reactor components and bulk processing of sodium as well as for sodium fire fighting

  12. Water Evaporation from Acoustically Levitated Aqueous Solution Droplets.

    Science.gov (United States)

    Combe, Nicole A; Donaldson, D James

    2017-09-28

    We present a systematic study of the effect of solutes on the evaporation rate of acoustically levitated aqueous solution droplets by suspending individual droplets in a zero-relative humidity environment and measuring their size as a function of time. The ratios of the early time evaporation rates of six simple salts (NaCl, NaBr, NaNO 3 , KCl, MgCl 2 , CaCl 2 ) and malonic acid to that of water are in excellent agreement with predictions made by modifying the Maxwell equation to include the time-dependent water activity of the evaporating aqueous salt solution droplets. However, the early time evaporation rates of three ammonium salt solutions (NH 4 Cl, NH 4 NO 3 , (NH 4 ) 2 SO 4 ) are not significantly different from the evaporation rate of pure water. This finding is in accord with a previous report that ammonium sulfate does not depress the evaporation rate of its solutions, despite reducing its water vapor pressure, perhaps due to specific surface effects. At longer evaporation times, as the droplets approach crystallization, all but one (MgCl 2 ) of the solution evaporation rates are well described by the modified Maxwell equation.

  13. Pulse Radiolysis of Adrenaline in Acid Aqueous Solutions

    DEFF Research Database (Denmark)

    Gohn, M.; Getoff, N.; Bjergbakke, Erling

    1976-01-01

    Pulse radiolysis of adrenaline in acid aqueous solutions (pH 1–3) was carried out. The rate constants for the reactions of adrenaline with H and OH were determined: k(H + adr.) = (0·9±0·1) × 109 dm3 mol−1s−1; k(OH + adr.) = (1·65±0·15) × 1010 dm3 mol−1s−1. The H-adduct of adrenaline has two λmax...

  14. Gelatin behaviour in dilute aqueous solution : designing a nanoparticulate formulation

    OpenAIRE

    Farrugia, Claude; Groves, Michael J.

    1999-01-01

    Although it has been claimed that nanoparticles can be produced from gelatin, a naturally occurring polypeptide, the commercial conversion of animal collagen to gelatin results in a heterogeneous product with a wide molecular-weight range. This is probably responsible for the widely observed variation in the experimental conditions required for nanoparticle formation. In this study, 0.2% w/v aqueous B225 gelatin solutions were incubated under various conditions of time, temperature, pH an...

  15. Plasma induced degradation of benzidine in aqueous solution

    International Nuclear Information System (INIS)

    Gao Jinzhang; Gai Ke; Yang Wu; Dong Yanjie

    2003-01-01

    The degradation of benzidine in aqueous solution by the low temperature plasma was examined. The results showed that the concentration of medium and the value of pH have an appreciable effect on the degradation of benzidine. What is more important is that iron ions acting as a catalyst play an important role in this reaction. For exploring the degradation mechanism of benzidine, some of the intermediate products were recorded by HPLC (high performance liquid chromatography)

  16. Volumetric studies of some amino acids in binary aqueous solutions ...

    Indian Academy of Sciences (India)

    Unknown

    0 values of glycine, L-alanine, and L-valine in aqueous MgCl2⋅6H2O solutions at. 298⋅15 K in order to describe the temperature dependence behaviour of partial molar quantities. Group contributions to partial molar volumes have been determined for the amino acids. The trends of transfer volumes (∆Vφ. 0) have been ...

  17. Tyrosine-sensitized photodimerization of thymine in aqueous solution

    International Nuclear Information System (INIS)

    Kaneko, M.; Matsuyama, A.; Nagata, C.

    1978-01-01

    Photodimerization of thymine in aqueous solution in the presence of tyrosine was studied with monochromatic UV irradiation. The total dimer formation was sensitized in the presence of tyrosine. The action spectrum of sensitized total dimer formation has a peak near 280 nm corresponding to the absorption maximum of tyrosine. Triplet quenchers reduced the sensitization substantially. It seems probable that tyrosine-sensitized photodimerization of thymine occurred via triplet-triplet energy transfer from tyrosine to thymine. (author)

  18. Luminescence properties of tetravalent uranium in aqueous solution

    International Nuclear Information System (INIS)

    Kirishima, A.; Kimura, T.; Nagaishi, R.; Tochiyama, O.

    2004-01-01

    The luminescence spectra of U 4+ in aqueous solutions were observed in the UV-VIS region at ambient and liquid nitrogen temperatures. The excitation spectrum indicates that the luminescence is arising from the deexcitation of a 5f electron at the 1 S 0 level and no other emissions of U 4+ in aqueous solutions were detected for other f-f transitions. All the luminescence peaks were assigned to the transitions from 1 S 0 to lower 5f levels. To estimate the luminescence lifetime, luminescence decay curves were measured using time-resolved laser-induced fluorescence spectroscopy. At room temperature, the decay curve indicated that the lifetime was shorter than 20 ns. On the other hand, the frozen sample of U 4+ in aqueous solution at liquid nitrogen temperature showed the same emission spectrum as at room temperature and its lifetime was 149 ns in H 2 O system and 198 ns in D 2 O system. The longer lifetime at liquid nitrogen temperature made it possible to measure the spectrum of U 4+ at the concentration as low as 10 -6 M. The difference in the anion species (ClO 4 - , Cl - , SO 4 2- ) affected the structure of the emission spectrum to some extent. (orig.)

  19. Dermal absorption of a dilute aqueous solution of malathion

    Directory of Open Access Journals (Sweden)

    Scharf John

    2008-01-01

    Full Text Available Malathion is an organophosphate pesticide commonly used on field crops, fruit trees, livestock, agriculture, and for mosquito and medfly control. Aerial applications can result in solubilized malathion in swimming pools and other recreational waters that may come into contact with human skin. To evaluate the human skin absorption of malathion for the assessment of risk associated with human exposures to aqueous solutions, human volunteers were selected and exposed to aqueous solutions of malathion. Participants submerged their arms and hands in twenty liters of dilute malathion solution in either a stagnant or stirred state. The "disappearance method" was applied by measuring malathion concentrations in the water before and after human exposure for various periods of time. No measurable skin absorption was detected in 42% of the participants; the remaining 58% of participants measured minimal absorbed doses of malathion. Analyzing these results through the Hazard Index model for recreational swimmer and bather exposure levels typically measured in contaminated swimming pools and surface waters after bait application indicated that these exposures are an order of magnitude less than a minimal dose known to result in a measurable change in acetylcholinesterase activity. It is concluded that exposure to aqueous malathion in recreational waters following aerial bait applications is not appreciably absorbed, does not result in an effective dose, and therefore is not a public health hazard.

  20. Dissolution of lignin in green urea aqueous solution

    Science.gov (United States)

    Wang, Jingyu; Li, Ying; Qiu, Xueqing; Liu, Di; Yang, Dongjie; Liu, Weifeng; Qian, Yong

    2017-12-01

    The dissolution problem is the main obstacle for the value-added modification and depolymerization of industrial lignin. Here, a green urea aqueous solution for complete dissolution of various lignin is presented and the dissolution mechanism is analyzed by AFM, DLS and NMR. The results show that the molecular interaction of lignin decreases from 32.3 mN/m in pure water to 11.3 mN/m in urea aqueous solution. The immobility of 1H NMR spectra and the shift of 17O NMR spectra of urea in different lignin/urea solutions indicate that the oxygen of carbonyl in urea and the hydrogen of hydroxyl in lignin form new hydrogen bonds and break the original hydrogen bonds among lignin molecules. The shift of 1H NMR spectra of lignin and the decrease of interactions in model compound polystyrene indicate that urea also breaks the π-π interactions between aromatic rings of lignin. Lignin dissolved in urea aqueous has good antioxidant activity and it can scavenge at least 63% free radicals in 16 min.

  1. Removal of fluoride ions from aqueous solution by waste mud

    International Nuclear Information System (INIS)

    Kemer, Baris; Ozdes, Duygu; Gundogdu, Ali; Bulut, Volkan N.; Duran, Celal; Soylak, Mustafa

    2009-01-01

    The present study was carried out to assess the ability of original waste mud (o-WM) and different types of activated waste mud which are acid-activated (a-WM) and precipitated waste mud (p-WM), in order to remove excess of fluoride from aqueous solution by using batch technique. The p-WM exhibited greater performance than the others. Adsorption studies were conducted as a function of pH, contact time, initial fluoride concentration, adsorbent concentration, temperature, etc. Studies were also performed to understand the effect of some co-existing ions present in aqueous solutions. Adsorption process was found to be almost independent of pH for all types of waste mud. Among the kinetic models tested for p-WM, pseudo-second-order model fitted the kinetic data well with a perfect correlation coefficient value of 1.00. It was found that the adequate time for the adsorption equilibrium of fluoride was only 1 h. Thermodynamic parameters including the Gibbs free energy (ΔG o ), enthalpy (ΔH o ), and entropy (ΔS o ) revealed that adsorption of fluoride ions on the p-WM was feasible, spontaneous and endothermic in the temperature range of 0-40 deg. C. Experimental data showed a good fit with the Langmuir and Freundlich adsorption isotherm models. Results of this study demonstrated the effectiveness and feasibility of WM for removal of fluoride ions from aqueous solution.

  2. Removal of fluoride ions from aqueous solution by waste mud

    Energy Technology Data Exchange (ETDEWEB)

    Kemer, Baris; Ozdes, Duygu; Gundogdu, Ali; Bulut, Volkan N.; Duran, Celal [Karadeniz Technical University, Faculty of Arts and Sciences, Department of Chemistry, 61080 Trabzon (Turkey); Soylak, Mustafa, E-mail: soylak@erciyes.edu.tr [Erciyes University, Faculty of Arts and Sciences, Department of Chemistry, 38039 Kayseri (Turkey)

    2009-09-15

    The present study was carried out to assess the ability of original waste mud (o-WM) and different types of activated waste mud which are acid-activated (a-WM) and precipitated waste mud (p-WM), in order to remove excess of fluoride from aqueous solution by using batch technique. The p-WM exhibited greater performance than the others. Adsorption studies were conducted as a function of pH, contact time, initial fluoride concentration, adsorbent concentration, temperature, etc. Studies were also performed to understand the effect of some co-existing ions present in aqueous solutions. Adsorption process was found to be almost independent of pH for all types of waste mud. Among the kinetic models tested for p-WM, pseudo-second-order model fitted the kinetic data well with a perfect correlation coefficient value of 1.00. It was found that the adequate time for the adsorption equilibrium of fluoride was only 1 h. Thermodynamic parameters including the Gibbs free energy ({Delta}G{sup o}), enthalpy ({Delta}H{sup o}), and entropy ({Delta}S{sup o}) revealed that adsorption of fluoride ions on the p-WM was feasible, spontaneous and endothermic in the temperature range of 0-40 deg. C. Experimental data showed a good fit with the Langmuir and Freundlich adsorption isotherm models. Results of this study demonstrated the effectiveness and feasibility of WM for removal of fluoride ions from aqueous solution.

  3. Ultrafast dynamics of hydrogen bond exchange in aqueous ionic solutions.

    Science.gov (United States)

    Park, Sungnam; Odelius, Michael; Gaffney, Kelly J

    2009-06-04

    The structural and dynamical properties of aqueous ionic solutions influence a wide range of natural and biological processes. In these solutions, water has the opportunity to form hydrogen bonds with other water molecules and anions. Knowing the time scale with which these configurations interconvert represents a key factor to understanding the influence of molecular scale heterogeneity on chemical events in aqueous ionic solutions. We have used ultrafast IR spectroscopy and Car-Parrinello molecular dynamics (CPMD) simulations to investigate the hydrogen bond (H-bond) structural dynamics in aqueous 6 M sodium perchlorate (NaClO4) solution. We have measured the H-bond exchange dynamics between spectrally distinct water-water and water-anion H-bond configurations with 2DIR spectroscopy and the orientational relaxation dynamics of water molecules in different H-bond configurations with polarization-selective IR pump-probe experiments. The experimental H-bond exchange time correlates strongly with the experimental orientational relaxation time of water molecules. This agrees with prior observations in water and aqueous halide solutions, and has been interpreted within the context of an orientational jump model for the H-bond exchange. The CPMD simulations performed on aqueous 6 M NaClO4 solution clearly demonstrate that water molecules organize into two radially and angularly distinct structural subshells within the first solvation shell of the perchlorate anion, with one subshell possessing the majority of the water molecules that donate H-bonds to perchlorate anions and the other subshell possessing predominantly water molecules that donate two H-bonds to other water molecules. Due to the high ionic concentration used in the simulations, essentially all water molecules reside in the first ionic solvation shells. The CPMD simulations also demonstrate that the molecular exchange between these two structurally distinct subshells proceeds more slowly than the H

  4. Removal of Copper (II Ions in Aqueous Solutions by Sorption onto Alkali Activated Fly Ash

    Directory of Open Access Journals (Sweden)

    Darmayanti Lita

    2018-01-01

    Full Text Available Fly ash is a particulate material produced from coal combustion power plants with major components are silica, alumina, iron oxide, calcium oxide, magnesium oxide, and carbon which are ideal for metal adsorbents. The potential use of fly ash in the wastewater treatment process is obvious because it can be obtained cheaply in large quatities and it can be used as an adsorbent. However, fly ash still shows lower adsorption capacity unless it is activated. In this study, fly ash activated by NaOH 14 M and KOH 14 M solutions. The batch experiments were carried out to study the sorption of copper ions from aqueous on alkali activated fly ash. The influence of initial concentration and contact time were examined at constant pH and dose of adsorbent. The sorption capacity of copper ions increased with the initial concentration and contact time. The sorption capacities followed the order Na1>Ka1>FA. The adsorption isotherm model exhibited that the Langmuir model is very suitable with copper ions adsorption onto fly ash and alkali activated fly ash. Kinetic study shows that adsorption of copper ions onto FA, Na1, and Ka1 follows the pseudo second-order kinetics.

  5. Mg-doped nano ferrihydrite - A new adsorbent for fluoride removal from aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Mohapatra, M., E-mail: mamatamohapatra@yahoo.com [Institute of Minerals and Materials Technology, Bhubaneswar 751 013, Orissa (India); Hariprasad, D.; Mohapatra, L.; Anand, S.; Mishra, B.K. [Institute of Minerals and Materials Technology, Bhubaneswar 751 013, Orissa (India)

    2012-03-01

    The present study evaluates synthesized Mg-doped nano ferrihydrite powder as an adsorbent for F{sup -} removal from aqueous solutions. High surface area Mg-doped ferrihydrite was prepared by co-precipitation method under controlled conditions. Samples were prepared by varying Mg content in the range of 0.39-1.12%. Preliminary test work revealed that under similar conditions, with the increase in Mg content from 0.39 to 0.98% in doped ferrihydrite, % F{sup -} adsorption increased from 66 to 91%. Hence this sample was characterized by XRD, TEM, SAED and TG-DTA. Batch adsorption experiments were carried out by varying contact time (30-480 min), initial pH (1.0-10), initial fluoride concentration (10-150 mg/L), adsorbent dose (0.5-4 g/L), temperature (20-45 Degree-Sign C) and Cl{sup -} or SO{sub 4}{sup 2-} concentrations (nil to 50 mg/L). The results showed 0.98% Mg-doped ferrihydrite to be an excellent fluoride adsorbent giving maximum adsorption capacity of 64 mg/g. The time data fitted well to pseudo second order kinetic model. The isothermal data followed Langmuir model. Thermodynamic parameters confirmed the adsorption process to be spontaneous and endothermic. 89% of fluoride could be desorbed from loaded sample using 1 M NaOH.

  6. Removal of ammonium from aqueous solutions using alkali-modified biochars

    Directory of Open Access Journals (Sweden)

    Zhigang Liu

    2016-10-01

    Full Text Available Biochars converted from agricultural residuals can effectively remove ammonium from water. This work further improved the sorption ability of biochars to aqueous ammonium through alkali modification. Three modified biochars were prepared from agricultural residuals pre-treated with NaOH solution through low-temperature (300 °C slow pyrolysis. The modified biochars effectively removed ammonium ions from water under various conditions with relatively fast adsorption kinetics (reached equilibrium within 10 h and extremely high adsorption capacity (>200 mg/g. The Langmuir maximum capacity of the three modified biochars were between 313.9 and 518.9 mg/g, higher than many other ammonium adsorbents. Although the sorption of ammonium onto the modified biochar was affected by pH and temperature, it was high under all of the tested conditions. Findings from this work indicated that alkali-modified biochars can be used as an alternative adsorbent for the removal of ammonium from wastewater.

  7. Removal of Cr6 + and Ni2+ from aqueous solution using bagasse and fly ash.

    Science.gov (United States)

    Rao, M; Parwate, A V; Bhole, A G

    2002-01-01

    Raw bagasse and fly ash, the waste generated in sugar mills and boilers respectively have been used as low-cost potential adsorbents. Raw bagasse was pretreated with 0.1N NaOH followed by 0.1N CH3COOH before its application. These low-cost adsorbents were used for the removal of chromium and nickel from an aqueous solution. The kinetics of adsorption and extent of adsorption at equilibrium are dependent on the physical and chemical characteristics of the adsorbent, adsorbate and experimental system. The effect of hydrogen ion concentration, contact time, sorbent dose, initial concentrations of adsorbate and adsorbent and particle size on the uptake of chromium and nickel were studied in batch experiments. The Sorption data has been correlated with Langmuir, Freundlich and Bhattacharya and Venkobachar adsorption models. The efficiencies of adsorbent materials for the removal of Cr(VI) and Ni(II) were found to be between 56.2 and 96.2% and 83.6 and 100%, respectively. These results were obtained at the optimized conditions of pH, contact time, sorbent dose, sorbate concentration of 100 mg/l and with the variation of adsorbent particles size between 0.075 and 4.75 mm. The order of selectivity is powdered activated carbon > bagasse > fly ash for Cr(VI) removal and powdered activated carbon > fly ash > bagasse for Ni(II) removal.

  8. Conductivity and electrochemical stability of concentrated aqueous choline chloride solutions

    Science.gov (United States)

    Grishina, E. P.; Kudryakova, N. O.

    2017-10-01

    The conductivity and electrochemical stability of choline chloride (ChCl) solutions with water contents ranging from 20 to 39 wt % are studied. Exposing ChCl to moist ambient air yields a highly concentrated aqueous solution that, as an electrolyte, exhibits the properties and variations in conductivity with temperature and concentration characteristic of other similar systems. Its electrochemical stability window, determined by cyclic voltammetry, is comparable to that of ChCl-based deep eutectic solvents (DESs). Products of the electrolysis of ChCl‒H2O mixtures seem to be less toxic than those of Reline, Ethaline, and Maline.

  9. WHATIF-AQ, Geochem Speciation and Saturation of Aqueous Solution

    International Nuclear Information System (INIS)

    Nielsen, Ole John; Jensen, Bror Skytte

    1988-01-01

    1 - Description of program or function: WHATIF-AQ is part of a family of programs for calculations of geochemistry in the near-field of radioactive waste with temperature gradients. The program calculates speciation and saturation indices for an aqueous solution at temperatures in the range 0 - 125 degrees C. The chemical equilibrium is determined by solving a set of nonlinear equations consisting of the equilibrium constant and mass balance constraints. 2 - Method of solution: The set of equations is solved using a generalized Newton-Raphson technique

  10. Oxidation of ammonium sulfite in aqueous solutions using ozone technology

    Science.gov (United States)

    Li, Yue; Shang, Kefeng; Lu, Na; Li, Jie; Wu, Yan

    2013-03-01

    How to deal with unstable ammonium sulfite, the byproduct of flue gas desulfuration by ammonia absorption methods, has been a difficult problem in recent years. Oxidation of ammonium sulfite in aqueous solutions using ozone produced by a surface discharge system was investigated in the paper. The oxidation efficiency of ammonium sulfite by ozone and traditional air aeration were compared, and the factors including ozone concentration, gas flow rate, initial concentration of ammonium sulfite solution and reaction temperature were discussed. The results show that the oxidation efficiency of ammonium sulfite by ozone technology reached nearly 100% under the optimum conditions, which had a significant increase compared with that by air aeration.

  11. Recovery of Ionic Liquids from aqueous solution by Nanofiltration

    OpenAIRE

    Fernández Dámaso, José Francisco

    2011-01-01

    The T-SAR methodology was combined with membrane characterization methods. An application of the combined approach was demonstrated with two commercial nanofiltration membranes and it was possible to successfully predict their performance for the recovery of ionic liquids from aqueous solution. Using model solutions of Pyr16 (CF3SO2)2N, it could be evidenced the formation of a new phase of ionic liquid during the concentration process. In this case, 66% of the ionic liquid was separated and t...

  12. [Extraction of lambda-cyhalothrin from aqueous dioxan solutions].

    Science.gov (United States)

    Shormanov, V K; Chigareva, E N; Belousova, O V

    2011-01-01

    The results of extraction of lambda-cigalotrin from dioxan aqueous solutions by hydrophobic organic solvents are presented. It is shown that the degree of extraction depends on the nature of the extractant, the water to dioxan ratio, and saturation of the water-dioxan layer with the electrolyte. The highest efficiency of lambda-cigalotrin extraction was achieved using chlorophorm as a solvent under desalination conditions. The extraction factor was calculated necessary to obtain the desired amount of lambda-cigalotrin from the water-dioxan solution (4:1) with the help of the extractants being used.

  13. The blue complexes of U in aqueous solutions

    International Nuclear Information System (INIS)

    Musikas, C.

    1976-01-01

    Mixed-valence uranium complexes were synthesized. Hydrolysis of hexavalent U leads to anionic species soluble in aqueous solutions when the UO 2 ++ ions are neutralized by tetraalkylammonium hydroxides. These complexes are polynuclear and the size and interatomic distances found for the polyanions are those of macromolecules. By hydrazine of these complexes, solutions were obtained and their absorption spectra studied. The spectra of U(VI) and U(V) ions are observed, together with new bands attributable to a charge transfer. It may be concluded that the blue complexes of uranium are type II composite-valence complexes for which the delocalization coefficient α can be calculated [fr

  14. Some reactions of oxidizing radicals with enzymes in aqueous solution

    International Nuclear Information System (INIS)

    Cundall, R.B.; Bisby, R.H.; Hoe, S.T.; Sims, H.E.; Anderson, R.F.

    1979-01-01

    A range of oxidizing radicals including some inorganic radical anions and the superoxide radical, can be generated by radiolysis of aqueous solutions. These radicals are more selective in their reactions with amino acids than the hydroxyl radical. Factors controlling the apparent reactivity of radical anions with proteins, such as free radical equilibria and ion-binding, are described. The superoxide radical inactivates papain by reaction with the cysteine residue. This reaction has been studied in solutions subjected to radiations of varying linear energy transfer. (Auth.)

  15. Free radicals generated by radiolysis of aqueous solutions

    International Nuclear Information System (INIS)

    Schwarz, H.A.

    1981-01-01

    The free radicals produced in the radiolysis of aqueous solutions span the range of redox potentials from -2.9 to +2.65 volts. The identity and nature of these radicals were discussed. Most of the discussion was results obtained with low LET radiation sources ( 60 Co gamma radiation or electron accelerators). Water radiolysis provides the synthesis of many radicals and radical ions in aqueous solution. The primary radicals, e/sub aq/ - H, OH, are well characterized. The radical population can be made to be 90% pure OH (or O - ) if N 2 O solutions are irradiated, the remaining 10% being H atoms. 55% of the radicals can be converted to H atoms in acid solution or in neutral phosphate solutions(e/sub aq/ - reacts with H 2 PO 4- to produce H). The remaining 45% (OH radicals) are difficult to convert to H by reaction with H 2 , due to the slow rate of the reaction. About 100 atmospheres of H 2 are required to do the conversion in less than 10 - 6 sec. 3 figures, 3 tables. (DP)

  16. Biosorption of mercury from aqueous solutions using highly characterised peats

    Directory of Open Access Journals (Sweden)

    A.M. Rizzuti

    2015-02-01

    Full Text Available This research investigated the biosorption of mercury from aqueous solutions by six highly characterised peats. Samples of the peats were tested both in unaltered condition and after being treated with hydrochloric acid (HCl to free up any occupied exchange sites. Other variables tested were sample dose, contact time, mixing temperature, and the concentration and pH of the mercury solution. Desorption studies were also performed, and tests were done to determine whether the peats could be re-used for mercury biosorption. The results indicate that all six peat types biosorb mercury from aqueous solutions extremely well (92−100 % removal and that their mercury removal capacities are not significantly affected by manipulation of the various factors tested. The factor that had the greatest impact on the mercury removal capacities of the peats was the pH of the mercury solution. The optimal mercury solution pH for mercury removal was in the range 5−7 for four of the peats and in the range 2−3 for the other two. The desorption results indicate that it may be possible to recover up to 41 % of the removed mercury. All of the peat types tested can be repeatedly re-used for additional mercury biosorption cycles. Hence, their disposal should not become a hazardous waste problem.

  17. Adsorption of nicotine on different zeolite types, from aqueous solutions

    Directory of Open Access Journals (Sweden)

    Stošić Dušan K.

    2007-01-01

    Full Text Available The plant alkaloid, nicotine, is a strongly toxic heterocyclic compound: the lethal dose for an adult human being (40-60 mg is importantly lower in comparison with the other known poisons such as arsenic or strychni­ne. Cigarettes represent "the most toxic and addictive form of nicotine". Besides the negative effects of nicotine on public health produced by self-administration, recently another potentially very dangerous effect has been recognized: because of its miscibility with water, nicotine can be found in industrial wastewaters, and consequently, in groundwater. Therefore, the problem of nicotine removal from aqueous solutions has became an interesting topic. In this work, the removal of nicotine has been probed by adsorption on solid materials. Adsorption of nicotine on different zeolites (clinoptilolite, ZSM-5 and β zeolite and on activated carbon was investigated from aqueous solutions, at 298 K. The obtained results are presented as adsorption isotherms: the amount of adsorbed nicotine as a function of equilibrium concentration. These data were obtained from the residual amount of nicotine in the aqueous phase, by the use of UV spectroscopy. The highest amounts of adsorbed nicotine was found for activated carbon and p zeolite (~ mmol·g-1. The attempt to modify the adsorption properties of ZSM-5 zeolite has been also done: ZSM-5 was modified by ion-exchange with VIII group metal (Cu2+ and Fe3+. In addition, the adsorption of nicotine on ZSM-5 zeolite with different Si/Al ratios has been done. It has been noticed that ion-exchange did not improve the adsorption possibilities, while the adsorption was importantly lower in the case of higher silicon content in ZMS-5 structure. 13C NMR spectra were collected for suspensions formed of solid adsorbent and aqueous solution of nicotine; in this way, the part of nicotine molecule which is most probably connected with the adsorbent was recognized.

  18. Hydrate phase equilibria of CO2+N2+aqueous solution of THF, TBAB or TBAF system

    DEFF Research Database (Denmark)

    Sfaxi, Imen Ben Attouche; Durand, Isabelle; Lugo, Rafael

    2014-01-01

    We report hydrate dissociation conditions of CO2 (15 and 30mol%)+N2 (85 and 70mol%) in the presence of aqueous solutions of THF, TBAB or TBAF. The concentrations of TBAB and TBAF in the aqueous solutions are 5wt% and 9wt% while THF concentration in aqueous solution is 3mol%. Two different experim...

  19. Pulse radiolysis studies of iron(I) in aqueous solutions

    International Nuclear Information System (INIS)

    Nenadovic, M.T.; Micic, O.I.; Muk, A.A.

    1980-01-01

    The absorption spectrum and decay kinetics of the products of the reactions of iron(II) ions with hydrated electrons and hydrogen atoms have been studied in aqueous solution using pulse-radiolysis techniques. Iron(I) is formed by reaction with hydrated electrons and its absorption spectrum is reported and discussed. The formation of molecular hydrogen by reaction of Fe + with water is suppressed by other solutes present in the solutions. In acidic solutions containing [SO 4 ] 2- , the intermediates formed in the reaction with H atoms decay by a first-order process and produce molecular hydrogen, but the rate of their decay does not depend only on the oxonium ion concentration but also on intermolecular rearrangement in the [FeSO 4 -H] complex. (author)

  20. Efficient removal of Cd{sup 2+} from aqueous solutions using by-product of biodiesel production

    Energy Technology Data Exchange (ETDEWEB)

    Ribeiro, Rita F.L., E-mail: ritaflavia@gmail.com [Departamento de Quimica, Instituto de Ciencias Exatas, Universidade Federal de Minas Gerais, Belo Horizonte, MG (Brazil); Soares, Vitor C., E-mail: vcelios@gmail.com [Departamento de Quimica, Instituto de Ciencias Exatas, Universidade Federal de Minas Gerais, Belo Horizonte, MG (Brazil); Costa, Leticia M., E-mail: leticia@qui.ufmg.br [Departamento de Quimica, Instituto de Ciencias Exatas, Universidade Federal de Minas Gerais, Belo Horizonte, MG (Brazil); Nascentes, Clesia C., E-mail: clesia@qui.ufmg.br [Departamento de Quimica, Instituto de Ciencias Exatas, Universidade Federal de Minas Gerais, Belo Horizonte, MG (Brazil)

    2012-10-30

    Highlights: Black-Right-Pointing-Pointer Sorbents were prepared from radish cake, a waste from biodiesel production. Black-Right-Pointing-Pointer The chemical treatments used were simple, low-cost and enhanced the Cd{sup 2+} sorption. Black-Right-Pointing-Pointer The cadmium sorption process was evaluated by Freundlich and Langmuir models. Black-Right-Pointing-Pointer Chemically treated radish cake is an excellent alternative for removal of Cd{sup 2+}. Black-Right-Pointing-Pointer Desorption studies demonstrated that the sorbent-metal interaction is reversible. - Abstract: In this study, chemically modified radish cake, a by-product of biodiesel production, was used to remove Cd{sup 2+} from aqueous solutions. The chemical modification was carried out by treating the radish cake with citric acid (CRC), NaOH (NRC) or the combination of citric acid and NaOH (CNRC). The sorbents were characterized by elemental analysis, surface area analysis, infrared spectroscopy (FTIR), potentiometric titration (PT), scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS), and thermogravimetric analysis (TGA). The effect of the chemical treatment and contact time on cadmium sorption was evaluated. The equilibrium data were analyzed using Freundlich and Langmuir models. The maximum sorption capacity obtained by the Langmuir isotherm was 58.5 mg/g and 64.10 mg/g for the CRC, and CNRC sorbents, respectively. Complete desorption of Cd{sup 2+} was achieved using 0.1 mol/L HNO{sub 3}. The results obtained demonstrate that chemically modified radish cake has potential as a sorbent for Cd{sup 2+} removal from aqueous solutions.

  1. Chemical metallization of KMPR photoresist polymer in aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Zeb, Gul [MiQro Innovation Collaborative Centre (C2MI), 45, boul. de l' Aéroport, Bromont, QC, J2L 1S8 (Canada); Mining & Materials Engineering, McGill University, 3610,University Street, Montreal, QC, H3A 0C5 (Canada); Duong, Xuan Truong [Department of Mechanical Engineering, Ecole polytechnique de Montréal, Montréal, QC, H3C 3T5 (Canada); Thai Nguyen University of Technology, 3-2 Street, Thai Nguyen City (Viet Nam); Vu, Ngoc Pi; Phan, Quang The; Nguyen, Duc Tuong; Ly, Viet Anh [Thai Nguyen University of Technology, 3-2 Street, Thai Nguyen City (Viet Nam); Salimy, Siamak [ePeer Review LLC, 145 Pine Haven Shores Rd, Suite 1000-X, Shelburne, VT 05482 (United States); Le, Xuan Tuan, E-mail: xuantuan.le@teledyne.com [MiQro Innovation Collaborative Centre (C2MI), 45, boul. de l' Aéroport, Bromont, QC, J2L 1S8 (Canada); Thai Nguyen University of Technology, 3-2 Street, Thai Nguyen City (Viet Nam)

    2017-06-15

    Highlights: • Electroless deposition of Ni-B film on KMPR photoresist polymer insulator with excellent adhesion has been achieved. • This metallization has been carried out in aqueous solutions at low temperature. • Polyamine palladium complexes grafts serve as seeds for the electroless plating on KMPR. • This electroless metallization process is simple, industrially feasible, chromium-free and environment-friendly. - Abstract: While conventional methods for preparing thin films of metals and metallic alloys on insulating substrates in the field of microelectromechanical systems (MEMS) include vapor deposition techniques, we demonstrate here that electroless deposition can be considered as an alternate efficient approach to metallize the surface of insulating substrates, such as KMPR epoxy photoresist polymer. In comparison with the physical and chemical vapor deposition methods, which are well-established for metallization of photoresist polymers, our electroless nickel plating requires only immersing the substrates into aqueous solutions in open air at low temperatures. Thin films of nickel alloy have been deposited electrolessly on KMPR surface, through a cost-effective and environmental chromium-free process, mediated through direct grafting of amine palladium complexes in aqueous medium. This covalent organic coating provides excellent adhesion between KMPR and the nickel film and allows better control of the palladium catalyst content. Covalent grafting and characterization of the deposited nickel film have been carried out by means of Fourier-transform infrared spectroscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy techniques.

  2. Opto-electrochemical spectroscopy of metals in aqueous solutions

    International Nuclear Information System (INIS)

    Habib, K.

    2016-01-01

    In the present investigation, holographic interferometry was utilized for the first time to determine the rate change of the electrical resistance of aluminium samples during the initial stage of anodisation processes in aqueous solution. In fact, because the resistance values in this investigation were obtained by holographic interferometry, electromagnetic method rather than electronic method, the abrupt rate change of the resistance was called electrical resistance–emission spectroscopy. The anodisation process of the aluminium samples was carried out by electrochemical impedance spectroscopy (EIS) in different sulphuric acid concentrations (1.0%–2.5% H 2 SO 4 ) at room temperature. In the meantime, the real time holographic interferometry was used to determine the difference between the electrical resistance of two subsequent values, dR, as a function of the elapsed time of the EIS experiment for the aluminium samples in 1.0%, 1.5%, 2.0%, and 2.5% H 2 SO 4 solutions. The electrical resistance–emission spectra of the present investigation represent a detailed picture of not only the rate change of the electrical resistance throughout the anodisation processes but also the spectra represent the rate change of the growth of the oxide films on the aluminium samples in different solutions. As a result, a new spectrometer was developed based on the combination of the holographic interferometry and electrochemical impedance spectroscopy for studying in situ the electrochemical behavior of metals in aqueous solutions.

  3. Synthesis of sub-millimeter calcite from aqueous solution

    Science.gov (United States)

    Reimi, M. A.; Morrison, J. M.; Burns, P. C.

    2011-12-01

    A novel aqueous synthesis that leads to the formation of calcite (CaCO3) crystals, up to 500μm in diameter, will be used to facilitate the study of contaminant transport in aqueous environmental systems. Existing processes tend to be complicated and often yield nanometer-sized or amorphous CaCO3. The synthesis method presented here, which involves slow mixing of concentrated solutions of CaCl2 ¬and (NH4)2CO3, produces single crystals of rhombohedral calcite in 2 to 4 days. Variations on the experimental method, including changes in pH and solution concentration, were explored to optimize the synthesis. Scanning Electron Microscope images show the differences in size and purity observed when the crystals are grown at pH values ranging from 2 to 6. The crystals grown from solutions of pH 2 were large (up to 500 micrometers in diameter) with minimal polycrystalline calcium carbonate, while crystals grown from solutions with pH values beyond 4 were smaller (up to 100 micrometers in diameter) with significant polycrystalline calcium carbonate. The synthesis method, materials characterization, and use in future actinide contaminant studies will be discussed.

  4. Aqueous solution of basic fuchsin as food irradiation dosimeter

    International Nuclear Information System (INIS)

    Khan, H.M.; Naz, S.

    2006-01-01

    Dosimetric characterization of aqueous solution of basic fuchsin has been studied spectrophotometrically for the possible application in the low-dose food irradiation dosimetry. Absorption spectra of unirradiated and irradiated solutions were determined and decrease in the absorption with the radiation dose was noted down. Radiation-induced bleaching of the dye was measured at wavelengths of maximum absorption λ max (540nm) as well as 510, 460 and 400 nm wavelengths. At all these wavelengths, the decrease in the absorbance of the dosimeter was linear with respect to the absorbed dose from 0.05 to 0.6 kGy. The stability of dosimetric solution during the post-irradiation storage in the dark at room temperature showed that after initial bleaching during first eight days, the response was almost stable for about 34 days. The effect of different light and temperature conditions also showed that the response gradually decreased during the storage period of 34 days, which shows that the basic fuchsin dye is photosensitive as well as thermally sensitive. The possibility of using aqueous solution of basic fuchsin as food irradiation dosimeter will be discussed. (authors)

  5. Graph Theory and Ion and Molecular Aggregation in Aqueous Solutions

    Science.gov (United States)

    Choi, Jun-Ho; Lee, Hochan; Choi, Hyung Ran; Cho, Minhaeng

    2018-04-01

    In molecular and cellular biology, dissolved ions and molecules have decisive effects on chemical and biological reactions, conformational stabilities, and functions of small to large biomolecules. Despite major efforts, the current state of understanding of the effects of specific ions, osmolytes, and bioprotecting sugars on the structure and dynamics of water H-bonding networks and proteins is not yet satisfactory. Recently, to gain deeper insight into this subject, we studied various aggregation processes of ions and molecules in high-concentration salt, osmolyte, and sugar solutions with time-resolved vibrational spectroscopy and molecular dynamics simulation methods. It turns out that ions (or solute molecules) have a strong propensity to self-assemble into large and polydisperse aggregates that affect both local and long-range water H-bonding structures. In particular, we have shown that graph-theoretical approaches can be used to elucidate morphological characteristics of large aggregates in various aqueous salt, osmolyte, and sugar solutions. When ion and molecular aggregates in such aqueous solutions are treated as graphs, a variety of graph-theoretical properties, such as graph spectrum, degree distribution, clustering coefficient, minimum path length, and graph entropy, can be directly calculated by considering an ensemble of configurations taken from molecular dynamics trajectories. Here we show percolating behavior exhibited by ion and molecular aggregates upon increase in solute concentration in high solute concentrations and discuss compelling evidence of the isomorphic relation between percolation transitions of ion and molecular aggregates and water H-bonding networks. We anticipate that the combination of graph theory and molecular dynamics simulation methods will be of exceptional use in achieving a deeper understanding of the fundamental physical chemistry of dissolution and in describing the interplay between the self-aggregation of solute

  6. Graph Theory and Ion and Molecular Aggregation in Aqueous Solutions.

    Science.gov (United States)

    Choi, Jun-Ho; Lee, Hochan; Choi, Hyung Ran; Cho, Minhaeng

    2018-04-20

    In molecular and cellular biology, dissolved ions and molecules have decisive effects on chemical and biological reactions, conformational stabilities, and functions of small to large biomolecules. Despite major efforts, the current state of understanding of the effects of specific ions, osmolytes, and bioprotecting sugars on the structure and dynamics of water H-bonding networks and proteins is not yet satisfactory. Recently, to gain deeper insight into this subject, we studied various aggregation processes of ions and molecules in high-concentration salt, osmolyte, and sugar solutions with time-resolved vibrational spectroscopy and molecular dynamics simulation methods. It turns out that ions (or solute molecules) have a strong propensity to self-assemble into large and polydisperse aggregates that affect both local and long-range water H-bonding structures. In particular, we have shown that graph-theoretical approaches can be used to elucidate morphological characteristics of large aggregates in various aqueous salt, osmolyte, and sugar solutions. When ion and molecular aggregates in such aqueous solutions are treated as graphs, a variety of graph-theoretical properties, such as graph spectrum, degree distribution, clustering coefficient, minimum path length, and graph entropy, can be directly calculated by considering an ensemble of configurations taken from molecular dynamics trajectories. Here we show percolating behavior exhibited by ion and molecular aggregates upon increase in solute concentration in high solute concentrations and discuss compelling evidence of the isomorphic relation between percolation transitions of ion and molecular aggregates and water H-bonding networks. We anticipate that the combination of graph theory and molecular dynamics simulation methods will be of exceptional use in achieving a deeper understanding of the fundamental physical chemistry of dissolution and in describing the interplay between the self-aggregation of solute

  7. Radiation dechlorination of PCE in aqueous solutions under various conditions

    International Nuclear Information System (INIS)

    Mucka, V.; Lizalova, B.; Pospisil, M.; Silber, R.; Polakova, D.

    2002-01-01

    Complete text of publication follows. Radiation technology of water purification from chlorinated compounds seems to be one of the promising method (Getoff, 1996), analogously as it was shown (Mueka et al., 2000) with radiation degradation of polychlorinated biphenyls (PCBs). A systematic study of dechlorination of tetrachloroethylene (PCE) in aqueous solutions (initial concentrations ranging from 9.2 x 10 -6 to 2.5 x 10 -4 mol dm -3 ), initiated by γ-rays of 60 Co or by accelerated electrons (EB, 4.5 MeV) in presence of various modifiers (atmospheric oxygen, N 2 O-oxide, HCO 3 - - and NO 3 - - ions as well as various pH-values), was the aim of this paper. The studies showed that both actual concentration c of PCE and radiation yield G(Cl - ) decreased rapidly with increasing dose up to the dose of 2 kGy and the degree of dechlorination raised sharply in this dose-interval. The dechlorination was slightly promoted by atmospheric oxygen. Similarly, a promotion effect was detected in the case of the PCE-solutions saturated, prior to their irradiation, with the N 2 O-oxide. On the other hand, a presence of NO 3 - - or HCO 3 - -ions in irradiated samples led to an inhibiting effect. The inhibiting effect increased markedly with increasing concentration of both at above-mentioned ions up to the concentration of about 100 mg dm -3 . A pronounced inhibition of γ-radiation dechlorination of PCE was observed in alkaline aqueous solutions. The results obtained in this paper support the idea that the radiation dechlorination of PCE in aqueous solutions proceeds via an oxidative mechanism in which the γ-irradiation was found to be more effective than the EB-irradiation

  8. Physical chemistry of the interface between oxide and aqueous solution

    International Nuclear Information System (INIS)

    Jolivet, J.P.

    1997-01-01

    The behavior and properties of small oxide particles in aqueous suspension are dominated by the physico-chemistry of their surface. It is electrostatically charged and strongly solvated. The origin of the surface charge is discussed through the MUSIC model [Hiemstra 1996], allowing to estimate the acid-base behavior of surface oxygen atoms. The stability of aqueous dispersions of particles is analysed following the DLVO model, with a special attention on the hydration layers allowing the peptization of flocs. Different adsorption mechanisms of metal cations are presented in terms of coordination chemistry (outer- and inner-sphere complexes) emphasizing the coordinating ability of the surface towards metal complexes in solution. The anion adsorption is also studied in relation with some interesting consequences on spinel iron oxide nano-particles. (author)

  9. Actinide removal from aqueous solution with activated magnetite

    International Nuclear Information System (INIS)

    Kochen, R.L.; Thomas, R.L.

    1987-01-01

    An actinide aqueous waste treatment process using activated magnetite has been developed at Rocky Flats. The use and effectiveness of various magnetites in lowering actinide concentrations in aqueous solution are described. Experiments indicate that magnetite particle size and pretreatment (activation of the magnetite surface with hydroxyl ions greatly influence the effective use of magnetite as an actinide adsorbent. With respect to actinide removal, Ba(OH) 2 -activated magnetite was more effective over a broader pH range than was NaOH-activated magnetite. About 50% less Ba(OH) 2 -activated magnetite was required to lower plutonium concentration from 10 -4 to 10 -8 g/l. 7 refs., 8 tabs

  10. Mutual diffusion of sodium hyaluranate in aqueous solutions

    International Nuclear Information System (INIS)

    Veríssimo, Luís M.P.; Valada, Teresa I.C.; Sobral, Abilio J.F.N.; Azevedo, Eduarda E.F.G.; Azevedo, Maria L.G.; Ribeiro, Ana C.F.

    2014-01-01

    Highlights: • Binary diffusion coefficients for the systems containing sodium hyaluronate. • Influence of the aggregation on diffusion of the sodium hyaluronate in the aqueous media. • Estimation of the thermodynamic and mobility factors from mutual diffusion. -- Abstract: The Taylor dispersion technique has been used for measuring mutual diffusion coefficients of sodium hyaluronate in aqueous solutions at T = 298.15 K, and concentrations ranging from (0.00 to 0.50) g · dm −3 . The results are interpreted on the basis of Nernst, and Onsager and Fuoss theoretical equations. From the diffusion coefficient at infinitesimal concentration, the limiting ionic conductivity and the tracer diffusion coefficient of hyaluronate ion were estimated. These studies have been complemented by molecular mechanics calculations

  11. Equilibrium modeling of removal of drimarine yello HG-3GL dye from aqueous solutions by low cost agricultural waste

    International Nuclear Information System (INIS)

    Bhatti, S.N.H.N.; Sadaf, S.; Sadaf, S.; Farrukh, Z.; Noreen, S.

    2014-01-01

    Pollution control is one of the leading issues of society today. The present study was designed to remove the Drimarine Yellow HF-3GL dye from aqueous solutions through biosorption. Sugarcane bagasse was used as biosorbent in native, acetic acid treated and immobilized form. Batch study was conducted to optimize different system variables like pH of solution, medium temperature, biosorbent concentration, initial dye concentration and contact time. Maximum dye removal was observed at pH 2, biosorbent dose of 0.05 g/50 mL and 40 degree C temperature. The equilibrium was achieved in 45-90 min. Different kinetic and equilibrium models were applied to the experimental results. The biosorption kinetic data was found to follow the pseudo second order kinetic model. Freundlich adsorption isotherm model showed a better fitness to the equilibrium data. The value of Gibbs free energy revealed that biosorption of Drimarine Yellow HF-3GL dye by native and pretreated sugarcane bagasse was a spontaneous process. Presence of salt and heavy metal ions in aqueous solution enhanced the biosorption capacity while presence of surfactants decreased the biosorption potential of biosorbent. Dye was desorbed by 1M NaOH solution. Fixed bed column study of Drimarine Yellow HF-3GL was carried out to optimize different parameters like bed height, flow rate and initial dye concentration. It was observed that biosorption capacity increases with increase in initial dye concentration and bed height but decreases with the increase in flow rate. The data of column study was explained very well by BDST model. FT-IR analysis confirmed the involvement of various functional groups, mainly hydroxyl, carboxyl and amine groups. The results proved that sugarcane bagasse waste biomass can be used as a favorable biosorbent for the removal of dyes from aqueous solutions. (author)

  12. Adsorption of anionic dyes from aqueous solutions onto coal fly ash and zeolite synthesized from coal fly ash

    International Nuclear Information System (INIS)

    Carvalho, Terezinha Elizabeth Mendes de

    2010-01-01

    Coal fly ash, a waste generated in coal-fired electric power plant, was used to synthesize zeolite by hydrothermal treatment with NaOH solution. The fly ash (CL-2) and this synthesized zeolite (ZM-2) that was characterized as hydroxy-sodalite were used as adsorbents for anionic dyes indigo carmine (IC), and reactive orange 16 (RO16) from aqueous solutions. Effects of contact time, initial dye concentration, pH, adsorbent mass, and temperature were evaluated in the adsorption processes. The kinetics studies indicated that the adsorption followed the pseudo-second order kinetics and that surface adsorption and intraparticle diffusion were involved in the adsorption mechanism. The thermodynamics parameters demonstrated that the adsorption was spontaneous for all adsorption processes. The enthalpy data confirmed the endothermic nature for all adsorption processes except for IC/ZM-2 system which was exothermic. The entropy data showed an increased disorder at the solid/solution interface during the adsorption for all systems except for IC/ZM-2 whose negative entropy value indicated a decreased disorder at the interface. The adsorption isotherms were closely fitted to the Langmuir linear equation. The maximum adsorption capacities were 1.48 mg/g for the IC/CL-2 system; 1.13 mg/g for IC/ZM-2; 0.96 mg/g for RO16/CL-2, and 1.14 mg/g for RO16/ZM-2 at room temperature. The desorption study carried out with water, with acid aqueous solutions, and with an alkali aqueous solution showed to be inefficient both for recovering the dyes and regenerating the adsorbents. (author)

  13. Process for disposal of aqueous solutions containing radioactive isotopes

    Science.gov (United States)

    Colombo, Peter; Neilson, Jr., Robert M.; Becker, Walter W.

    1979-01-01

    A process for disposing of radioactive aqueous waste solutions whereby the waste solution is utilized as the water of hydration to hydrate densified powdered portland cement in a leakproof container; said waste solution being dispersed without mechanical inter-mixing in situ in said bulk cement, thereafter the hydrated cement body is impregnated with a mixture of a monomer and polymerization catalyst to form polymer throughout the cement body. The entire process being carried out while maintaining the temperature of the components during the process at a temperature below 99.degree. C. The container containing the solid polymer-impregnated body is thereafter stored at a radioactive waste storage dump such as an underground storage dump.

  14. Determination of Ga in aqueous uranium solution by EDXRF

    International Nuclear Information System (INIS)

    Natarajan, V.; Purohit, P.J.; Goyal, Neelam; Seshagiri, T.K.; Godbole, S.V.; Manchanda, V.K.

    2009-01-01

    A method has been developed using EDXRF technique for the determination of gallium in aqueous solution using a set of solution standards in the concentration range 20-5000 μg/ml. When this method was applied to U containing solutions, the estimated values were found to be lower due to matrix effects. Hence the method was modified in order to determine gallium in the presence of uranium using lower tube current and another set of standards with U concentration at 100 mg/ml. The method was applicable for the estimation of Ga from 50 μg/ml to 5mg/ml (i.e.0.05-5% Ga in U). Three synthetic samples were analysed by the present methods in order to evaluate the method for its reliability and reproducibility. (author)

  15. Rapid structural analysis of nanomaterials in aqueous solutions

    Science.gov (United States)

    Ryuzaki, Sou; Tsutsui, Makusu; He, Yuhui; Yokota, Kazumichi; Arima, Akihide; Morikawa, Takanori; Taniguchi, Masateru; Kawai, Tomoji

    2017-04-01

    Rapid structural analysis of nanoscale matter in a liquid environment represents innovative technologies that reveal the identities and functions of biologically important molecules. However, there is currently no method with high spatio-temporal resolution that can scan individual particles in solutions to gain structural information. Here we report the development of a nanopore platform realizing quantitative structural analysis for suspended nanomaterials in solutions with a high z-axis and xy-plane spatial resolution of 35.8 ± 1.1 and 12 nm, respectively. We used a low thickness-to-diameter aspect ratio pore architecture for achieving cross sectional areas of analyte (i.e. tomograms). Combining this with multiphysics simulation methods to translate ionic current data into tomograms, we demonstrated rapid structural analysis of single polystyrene (Pst) beads and single dumbbell-like Pst beads in aqueous solutions.

  16. Process for disposal of aqueous solutions containing radioactive isotopes

    International Nuclear Information System (INIS)

    Colombo, P.; Neilson, R.M. Jr.; Becker, W.W.

    1979-01-01

    A process for disposing of radioactive aqueous waste solutions whereby the waste solution is utilized as the water of hydration to hydrate densified powdered portland cement in a leakproof container; said waste solution being dispersed without mechanical inter-mixing in situ in said bulk cement, thereafter the hydrated cement body is impregnated with a mixture of a monomer and polymerization catalyst to form polymer throughout the cement body. The entire process being carried out while maintaining the temperature of the components during the process at a temperature below 99 0 C. The container containing the solid polymer-impregnated body is thereafter stored at a radioactive waste storage dump such as an underground storage dump

  17. Use of magnesium-aluminium and zinc-aluminium hydroxycompounds as adsorbents of uranium ions in aqueous solutions

    International Nuclear Information System (INIS)

    Maki, Toshio

    1981-01-01

    It was found that precipitates formed by adding NaOH solution to the mixed solutions of MgSO 4 and Al 2 (SO 4 ) 3 with Mg/Al molar ratios of 2 to 4 and to the mixed solution of ZnSO 4 and Al 2 (SO 4 ) 3 with Zn/Al molar ratio of 2, respectively, can be used as efficient adsorbents of [UO 2 (CO 3 ) 3 ] 4- ions in aqueous alkaline carbonate solutions. The ideal structural formulas of the precipitates formed from the mixed Mg-Al solution with Mg/Al ratio of 2.0 and the mixed Zn-Al solution with Zn/Al ratio of 2.0 were estimated to be [Mg 4 Al 2 (OH) 12 ] 2+ [SO 4 .3H 2 O] 2- and [Zn 4 Al 2 (OH) 12 ] 2+ [SO 4 .3H 2 O] 2- , respectively. It has been shown that 0.1 g of the Mg-Al and Zn-Al double hydroxysulphate powders (particle size 70 - 170 μ uptake >97% of the U(VI) ions from 50 ml of an aqueous alkaline carbonate solution containing 100 ppm of U(VI) within 2 h at room temperature. The rates of adsorption of [UO 2 (CO 3 ) 3 ] 4- ions for the Mg-Al and Zn-Al double hydroxysulphate powders were both about 2 times that for the hydrous Ti(IV) oxide powders. Five weight percent sodium bicarbonate solution was found to be effective for the desorption of [UO 2 (CO 3 ) 3 ] 4- ions from the double hydroxysulphate powders. Adsorption capacity of the double hydroxysulphates was discussed in relation to their structure. (author)

  18. Preparation of fluorescent polyaniline nanoparticles in aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Alves, Kleber G. B. [Universidade Federal de Pernambuco, Departamento de Engenharia Mecanica (Brazil); Melo, Etelino F. de [Universidade Federal de Pernambuco, Departamento de Quimica Fundamental (Brazil); Andrade, Cesar A. S. [Universidade Federal de Pernambuco, Departamento de Bioquimica (Brazil); Melo, Celso P. de, E-mail: celso@df.ufpe.br [Universidade Federal de Pernambuco, Departamento de Fisica (Brazil)

    2013-01-15

    We report the synthesis of stable polyaniline nanoparticles (PANI{sub N}Ps) based on the chemical oxidative polymerization of aniline in aqueous solutions of surfactants. Surfactants of three different types-cationic (dodecyltrimethylammonium bromide-DTAB), anionic (sodium dodecyl sulfate-SDS), and non-ionic (Triton X-405-TX-405)-were used. The resulting PANI{sub N}Ps{sub s}urfactant samples were characterized through UV-Vis, fluorescence and Fourier transform infrared spectroscopies, and scanning electronic microscopy (SEM). We have verified that the color of the PANI{sub N}Ps{sub s}urfactant dispersions is affected by a change in the pH of the solution. The PANI-NPs{sub s}urfactant colloidal suspensions in aqueous solution present a surprising high fluorescence quantum yield value (ranging from 1.9 Multiplication-Sign 10{sup -3} to 6.9 Multiplication-Sign 10{sup -3}) that can be controlled as a function of the pH, a fact that we associate to the corresponding protonation degree of the PANI polymeric chains. We suggest that these fluorescent nanocomposites can find important technological applications in different areas such as organic light emitting devices, biosensors, and pigments for coatings.

  19. Removing Phosphorus from Aqueous Solutions Using Lanthanum Modified Pine Needles.

    Directory of Open Access Journals (Sweden)

    Xianze Wang

    Full Text Available The renewable pine needles was used as an adsorbent to remove phosphorus from aqueous solutions. Using batch experiments, pine needles pretreated with alkali-isopropanol (AI failed to effectively remove phosphorus, while pine needles modified with lanthanum hydroxide (LH showed relatively high removal efficiency. LH pine needles were effective at a wide pH ranges, with the highest removal efficiency reaching approximately 85% at a pH of 3. The removal efficiency was kept above 65% using 10 mg/L phosphorus solutions at desired pH values. There was no apparent significant competitive behavior between co-existing anions of sulfate, nitrate, and chloride (SO4(2-, NO3(- and Cl(-; however, CO3(2- exhibited increased interfering behavior as concentrations increased. An intraparticle diffusion model showed that the adsorption process occurred in three phases, suggesting that a boundary layer adsorption phenomena slightly affected the adsorption process, and that intraparticle diffusion was dominant. The adsorption process was thermodynamically unfavorable and non-spontaneous; temperature increases improved phosphorus removal. Total organic carbon (TOC assays indicated that chemical modification reduced the release of soluble organic compounds from 135.6 mg/L to 7.76 mg/L. This new information about adsorption performances provides valuable information, and can inform future technological applications designed to remove phosphorus from aqueous solutions.

  20. Preferential adsorption of uranium ions in aqueous solutions by polymers

    International Nuclear Information System (INIS)

    Sakuragi, Masako; Ichimura, Kunihiro; Fujishige, Shoei; Kato, Masao

    1981-01-01

    Amidoxime fiber and triazine fiber were prepared by chemical modification of commercially available polyacrylonitril fiber. It was found that the Amidoxime fiber is efficient to adsorb uranium ions in the artificial sea water. The efficiency of the preferential adsorption decreases by treatment the material with an acid-or an alkaline-solution. The triazine fiber adsorbs uranium ions only in aqueous solutions of such uranyl acetate, in the absence of other ions. In the artificial sea water, it adsorbs other ions instead of uranium. The preferential adsorption of uranium ions was further investigated with a series of polystyrenesulfonamides. Among the polystyrene derivatives, those having carboxyl groups, derived from imino diacetic acid (PSt-Imi), β-alanine (PSt-Ala), glycine (PSt-Gly), and sarcosine (PSt-Sar) were qualified for further discussion. However, it was found that the amount of adsorption of uranium ions by PSt-Imi decreases with increasing the volume of the artificial sea water and/or the duration of the treatment. Taking into account the facts, the preferential adsorption of uranium ions by PSt-Imi in aqueous solution was discussed in detail. (author)

  1. The radiolytic reduction of mercuric chloride in aqueous sugar solutions

    International Nuclear Information System (INIS)

    Johnston, F.J.

    1991-01-01

    The reduction of HgCl 2 has been measured in Co-60 γ-irradiated aqueous glucose, fructose and sucrose solutions. G-values for reduction, G(R), are substantially greater than 6 molecules per 100 eV in all systems from 1% by weight sugar to greater than 50%. Chain reduction occurs in glucose and fructose solutions with maximum G(R) values of 18-20 molecules per 100 eV occurring at 24% (1.0 M) sugar. The results are consistent with a mechanism in which HgCl radicals react with the organic solute to produce chain propagating free radicals. A dose rate independence of the chain length, after a brief ''induction'' period, is explained in terms of a chain termination by the incorporation of HgCl in growing Hg 2 Cl 2 particles. Reduction of Ag(I) and Cu(II) in aqueous sucrose and fructose systems took place with G(R) < 6 indicating the absence of reaction chains in these cases. (author)

  2. Removal of Cholera Toxin from Aqueous Solution by Probiotic Bacteria

    Directory of Open Access Journals (Sweden)

    Jussi A. O. Meriluoto

    2012-06-01

    Full Text Available Cholera remains a serious health problem, especially in developing countries where basic hygiene standards are not met. The symptoms of cholera are caused by cholera toxin, an enterotoxin, which is produced by the bacterium Vibrio cholerae. We have recently shown that human probiotic bacteria are capable of removing cyanobacterial toxins from aqueous solutions. In the present study we investigate the ability of the human probiotic bacteria, Lactobacillus rhamnosus strain GG (ATCC 53103 and Bifidobacterium longum 46 (DSM 14583, to remove cholera toxin from solution in vitro. Lactobacillus rhamnosus strain GG and Bifidobacterium longum 46 were able to remove 68% and 59% of cholera toxin from aqueous solutions during 18 h of incubation at 37 °C, respectively. The effect was dependent on bacterial concentration and L. rhamnosus GG was more effective at lower bacterial concentrations. No significant effect on cholera toxin concentration was observed when nonviable bacteria or bacterial supernatant was used.

  3. Preparation of fluorescent polyaniline nanoparticles in aqueous solutions

    International Nuclear Information System (INIS)

    Alves, Kleber G. B.; Melo, Etelino F. de; Andrade, César A. S.; Melo, Celso P. de

    2013-01-01

    We report the synthesis of stable polyaniline nanoparticles (PANI N Ps) based on the chemical oxidative polymerization of aniline in aqueous solutions of surfactants. Surfactants of three different types—cationic (dodecyltrimethylammonium bromide—DTAB), anionic (sodium dodecyl sulfate—SDS), and non-ionic (Triton X-405–TX-405)—were used. The resulting PANI N Ps s urfactant samples were characterized through UV–Vis, fluorescence and Fourier transform infrared spectroscopies, and scanning electronic microscopy (SEM). We have verified that the color of the PANI N Ps s urfactant dispersions is affected by a change in the pH of the solution. The PANI-NPs s urfactant colloidal suspensions in aqueous solution present a surprising high fluorescence quantum yield value (ranging from 1.9 × 10 −3 to 6.9 × 10 −3 ) that can be controlled as a function of the pH, a fact that we associate to the corresponding protonation degree of the PANI polymeric chains. We suggest that these fluorescent nanocomposites can find important technological applications in different areas such as organic light emitting devices, biosensors, and pigments for coatings.

  4. NMR studies of proton exchange kinetics in aqueous formaldehyde solutions.

    Science.gov (United States)

    Rivlin, Michal; Eliav, Uzi; Navon, Gil

    2014-05-01

    Aqueous solutions of formaldehyde, formalin, are commonly used for tissue fixation and preservation. Treatment with formalin is known to shorten the tissue transverse relaxation time T2. Part of this shortening is due to the effect of formalin on the water T2. In the present work we show that the shortening of water T2 is a result of proton exchange between water and the major constituent of aqueous solutions of formaldehyde, methylene glycol. We report the observation of the signal of the hydroxyl protons of methylene glycol at 2ppm to high frequency of the water signal that can be seen at low temperatures and at pH range of 6.0±1.5 and, at conditions where it cannot be observed by the single pulse experiment, it can be detected indirectly through the water signal by the chemical exchange saturation transfer (CEST) experiment. The above finding made it possible to obtain the exchange rate between the hydroxyl protons of the methylene glycol and water in aqueous formaldehyde solutions, either using the dispersion of the spin-lattice relaxation rate in the rotating frame (1/T1ρ) or, at the slow exchange regime, from the line width hydroxyl protons of methylene glycol. The exchange rate was ∼10(4)s(-1) at pH 7.4 and 37°C, the activation energy, 50.2kJ/mol and its pH dependence at 1.1°C was fitted to: k (s(-1))=520+6.5×10(7)[H(+)]+3.0×10(9)[OH(-)]. Copyright © 2014. Published by Elsevier Inc.

  5. Characterization of aqueous silver nitrate solutions for leakage tests

    Directory of Open Access Journals (Sweden)

    José Ferreira Costa

    2011-06-01

    Full Text Available OBJECTIVE: To determine the pH over a period of 168 h and the ionic silver content in various concentrations and post-preparation times of aqueous silver nitrate solutions. Also, the possible effects of these factors on microleakage test in adhesive/resin restorations in primary and permanent teeth were evaluated. MATERIAL AND METHODS: A digital pHmeter was used for measuring the pH of the solutions prepared with three types of water (purified, deionized or distilled and three brands of silver nitrate salt (Merck, Synth or Cennabras at 0, 1, 2, 24, 48, 72, 96 and 168 h after preparation, and storage in transparent or dark bottles. Ionic silver was assayed according to the post-preparation times (2, 24, 48, 72, 96, 168 h and concentrations (1, 5, 25, 50% of solutions by atomic emission spectrometry. For each sample of each condition, three readings were obtained for calculating the mean value. Class V cavities were prepared with enamel margins on primary and permanent teeth and restored with the adhesive systems OptiBond FL or OptiBond SOLO Plus SE and the composite resin Filtek Z-250. After nail polish coverage, the permanent teeth were immersed in 25% or 50% AgNO3 solution and the primary teeth in 5% or 50% AgNO3 solutions for microleakage evaluation. ANOVA and the Tukey's test were used for data analyses (α=5%. RESULTS: The mean pH of the solutions ranged from neutral to alkaline (7.9±2.2 to 11.8±0.9. Mean ionic silver content differed depending on the concentration of the solution (4.75±0.5 to 293±15.3 ppm. In the microleakage test, significant difference was only observed for the adhesive system factor (p=0.000. CONCLUSIONS: Under the tested experimental conditions and based on the obtained results, it may be concluded that the aqueous AgNO3 solutions: have neutral/alkaline pH and service life of up to 168 h; the level of ionic silver is proportional to the concentration of the solution; even at 5% concentration, the solutions were

  6. Sonochemical Degradation Kinetics of Methyl Violet in Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    Wei Lin Guo

    2003-01-01

    Full Text Available The sonochemical degradation in aqueous solution of methyl violet, chosen as a model of a basic dye, was studied. The ultrasonic degradation kinetics in water were found to be first-order and the degradation rate coefficient is 1.35×10-2 min-1 (R= 0.9934, n=8 at 20±1°C. The influence of the initial concentrations, reaction temperature and the pH of medium on the ultrasonic decomposition of methyl violet were also investigated.

  7. Thermal decomposition studies of aqueous and nitric solutions of hydroxyurea

    International Nuclear Information System (INIS)

    Shekhar Kumar; Pranay Kumar Sinha; Kamachi Mudali, U.; Natarajan, R.

    2012-01-01

    Hydroxyurea and its derivatives are important nonsalt forming reductants in partitioning of uranium and plutonium in the nuclear fuel reprocessing operations. There is no experimental data available in open literature describing pressurization due to the thermal decomposition of aqueous and nitric solutions of hydroxyurea at elevated temperatures. Authors studied thermal decomposition of hydroxyurea-nitric acid system and resultant pressurization at various concentrations of nitric acid in an adiabatic calorimeter in closed-vent conditions. During these experiments, pressurization was observed. In this paper, results of these experiments have been discussed. (author)

  8. Volumetric and calorimetric properties of aqueous ionene solutions.

    Science.gov (United States)

    Lukšič, Miha; Hribar-Lee, Barbara

    2017-02-01

    The volumetric (partial and apparent molar volumes) and calorimetric properties (apparent heat capacities) of aqueous cationic polyelectrolyte solutions - ionenes - were studied using the oscillating tube densitometer and differential scanning calorimeter. The polyion's charge density and the counterion properties were considered as variables. The special attention was put to evaluate the contribution of electrostatic and hydrophobic effects to the properties studied. The contribution of the CH 2 group of the polyion's backbone to molar volumes and heat capacities was estimated. Synergistic effect between polyion and counterions was found.

  9. Micellar effects on positronium lifetime in aqueous SDS solutions

    International Nuclear Information System (INIS)

    Vass, Sz.; Kajcsos, Zs.; Molnar, B.; Stergiopoulos, Ch.

    1981-09-01

    Positron lifetime measurements have been performed in aqueous SDS (Sodium Dodecyl Sulphate) solutions. The lifetime distributions measured by fast-slow coincidence technique have been found to be influenced by surfactant concentration, which varied in the range of 1.25x10 -3 - 3.2x10 -1 mol/dm 3 (i.e. 2.27x10 -5 - 5.82x10 -3 mole fractions). The lifetime of the long living component connected to positronium formation and decay increases with increasing surfactant concentration. Lifetime data suggest that a direct positronium-micelle electron-exchange reaction leading to pick-off annihilation is contraindicated. (author)

  10. The characterization methods for colloids in aqueous solutions

    International Nuclear Information System (INIS)

    Vuorinen, U.; Kumpulainen, H.

    1993-11-01

    This literature review deals with characterization methods for colloids in aqueous solutions and in groundwater. The basis for the review has been the needs of nuclear waste disposal studies and methods applicable in such studies. The methods considered include non-destructive laserspectroscopic methods (e.g. TRLFS, LPAS, PALS), several separation methods (e.g. ultrafiltration, dialysis, electrophoresis, field-flow-fractionation) and also some surface analytical methods, as well as some other methods giving additional information on formation and migration properties of colloids. (au.) (71 refs., 13 figs., 3 tabs.)

  11. Effect of γ-radiation on hypophosphite in aqueous solution

    International Nuclear Information System (INIS)

    Dedgaonkar, V.G.; Mahajan, C.T.

    1982-01-01

    Exposure to γ-radiation of aqueous solutions of hypophosphite ions at neutral pH showed the formation of phosphite and phosphate ions. The G[P(III)] value (=4.1) was independent of P(I) concentration over the range 0.25-100 mM. Beyond a critical dose which was concentration dependent, the G[P(V)] value increased sharply from 0.1 to 3.5. A mechanism is envisaged to explain the P(I)→P(III)→P(V) transformations. (author)

  12. Photoluminescence of hydrophilic silicon nanocrystals in aqueous solutions

    International Nuclear Information System (INIS)

    Prtljaga, Nikola; D'Amato, Elvira; Pitanti, Alessandro; Guider, Romain; Froner, Elena; Larcheri, Silvia; Scarpa, Marina; Pavesi, Lorenzo

    2011-01-01

    Stable aqueous solutions of undecylenic-acid-grafted silicon nanocrystals (Si-nc) were prepared. The time evolution of the photoluminescence properties of these hydrophilic silicon nanocrystals has been followed on different timescales (hours and days). On a short timescale (hours), Si-nc tend to agglomerate while the PL lineshape and intensity are stable. Agglomeration can be reduced by using suitable surfactants. On a long timescale (days), oxidation of Si-nc occurs even in the presence of surfactants. These two observations render Si-nc very useful as a labeling agent for biosensing.

  13. Photoluminescence of hydrophilic silicon nanocrystals in aqueous solutions

    Science.gov (United States)

    Prtljaga, Nikola; D'Amato, Elvira; Pitanti, Alessandro; Guider, Romain; Froner, Elena; Larcheri, Silvia; Scarpa, Marina; Pavesi, Lorenzo

    2011-05-01

    Stable aqueous solutions of undecylenic-acid-grafted silicon nanocrystals (Si-nc) were prepared. The time evolution of the photoluminescence properties of these hydrophilic silicon nanocrystals has been followed on different timescales (hours and days). On a short timescale (hours), Si-nc tend to agglomerate while the PL lineshape and intensity are stable. Agglomeration can be reduced by using suitable surfactants. On a long timescale (days), oxidation of Si-nc occurs even in the presence of surfactants. These two observations render Si-nc very useful as a labeling agent for biosensing.

  14. Photoluminescence of hydrophilic silicon nanocrystals in aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Prtljaga, Nikola; D' Amato, Elvira; Pitanti, Alessandro; Guider, Romain; Froner, Elena; Larcheri, Silvia; Scarpa, Marina; Pavesi, Lorenzo, E-mail: nikolap@science.unitn.it [Department of Physics, University of Trento, Via Sommarive 14, I-38123 Trento (Italy)

    2011-05-27

    Stable aqueous solutions of undecylenic-acid-grafted silicon nanocrystals (Si-nc) were prepared. The time evolution of the photoluminescence properties of these hydrophilic silicon nanocrystals has been followed on different timescales (hours and days). On a short timescale (hours), Si-nc tend to agglomerate while the PL lineshape and intensity are stable. Agglomeration can be reduced by using suitable surfactants. On a long timescale (days), oxidation of Si-nc occurs even in the presence of surfactants. These two observations render Si-nc very useful as a labeling agent for biosensing.

  15. Fluorescence of aqueous solutions of commercial humic products

    Science.gov (United States)

    Gosteva, O. Yu.; Izosimov, A. A.; Patsaeva, S. V.; Yuzhakov, V. I.; Yakimenko, O. S.

    2012-01-01

    We have studied the spectral luminescence characteristics of aqueous solutions of humic products obtained from different raw material sources, and their behavior as the excitation wavelength increases from 270 nm to 355 nm. We have identified differences in the spectral properties of industrial humic products from coalified materials, lignin-containing organic waste, and humic products from plant raw material (peat, sapropel, vermicompost). We have shown that humic products from plant raw material have spectral properties closer to those for humic substances in natural water or soil than humic products from coalified materials.

  16. Radiolysis of human gastric glycopolypeptides in aqueous solution

    International Nuclear Information System (INIS)

    Nagrani, S.; Bisby, R.H.

    1986-01-01

    The degradation of human gastric glycopolypeptides by hydroxyl radicals formed in irradiated N 2 0-saturated aqueous solution has been investigated. Gel exclusion chromatography shows the formation of lower molecular weight degradation products after irradiation and the appearance of unsaturated carbonyl-containing products which absorb in the ultra-violet. The radiation-induced destruction of individual monosaccharides in three human glycopolypeptides having different oligosaccharide chains has been measured. The results indicate that the structure of the oligosaccharide chain determines the extent of destruction of each type of monosaccharide present. (author)

  17. Volumetric properties of aqueous solutions of glutaric acid

    Energy Technology Data Exchange (ETDEWEB)

    Ben-Hamo, Meyrav [Department of Chemical Engineering, Ben Gurion University of the Negev, P.O. Box 653, Beer Sheva 84105 (Israel); Apelblat, Alexander [Department of Chemical Engineering, Ben Gurion University of the Negev, P.O. Box 653, Beer Sheva 84105 (Israel)]. E-mail: apelblat@bgu.ac.il; Manzurola, Emanuel [Department of Chemical Engineering, Ben Gurion University of the Negev, P.O. Box 653, Beer Sheva 84105 (Israel)

    2007-07-15

    Densities of aqueous solutions with molalities up to 6 mol . kg{sup -1} were determined at 5 K temperature intervals, from T = 288.15 K to T = 333.15 K. Densities served to evaluate the apparent molar volumes, V {sub 2,{phi}}(m, T), the cubic expansion coefficients, {alpha}(m, T), and the changes of isobaric heat capacities with respect to pressure, ({partial_derivative}C {sub P}/{partial_derivative}P) {sub T,m}. They were qualitatively correlated with the changes in the structure of water when glutaric acid is dissolved in it.

  18. Volumetric properties of aqueous solutions of glutaric acid

    International Nuclear Information System (INIS)

    Ben-Hamo, Meyrav; Apelblat, Alexander; Manzurola, Emanuel

    2007-01-01

    Densities of aqueous solutions with molalities up to 6 mol . kg -1 were determined at 5 K temperature intervals, from T = 288.15 K to T = 333.15 K. Densities served to evaluate the apparent molar volumes, V 2,φ (m, T), the cubic expansion coefficients, α(m, T), and the changes of isobaric heat capacities with respect to pressure, (∂C P /∂P) T,m . They were qualitatively correlated with the changes in the structure of water when glutaric acid is dissolved in it

  19. Radiolysis of phenol in aqueous solution at elevated temperatures

    International Nuclear Information System (INIS)

    Miyazaki, Toyoaki; Katsumura, Yosuke; Lin Mingzhang; Muroya, Yusa; Kudo, Hisaaki; Taguchi, Mitsumasa; Asano, Masaharu; Yoshida, Masaru

    2006-01-01

    γ-Radiolysis and pulse radiolysis of phenol in aqueous solution up to supercritical condition have been carried out. G-values of phenol consumption and product formation have been determined. While dihydroxybenzenes were major products at room temperature, multi-ring compounds and benzene were formed above 300 deg. C. This indicates reaction mechanism was changed above 300 deg. C, where phenoxyl radical plays a predominant role. This is supported by the observation of phenoxyl radical in pulse radiolysis. In supercritical water, the G-values increased with decrease of density

  20. Interaction of indium trichloride with calcium carbonate in aqueous solutions

    International Nuclear Information System (INIS)

    Kochetkova, N.V.; Toptygina, G.M.; Soklakova, O.V.; Evdokimov, V.I.

    1991-01-01

    Interaction of indium trichloride with calcium carbonate in aqueous solutions was studied, using methods of potentiometry, isothermal solubility and physicochemical computer simulating. The Gibb's energy value for crystal indium trihydroxide formation was calculated on the basis of experimental data on In(OH) 3 solubility. The value obtained was used for estimating equilibrium composition of InCl 3 -HCl-CaCO 3 -CO 2 -H 2 O system at a temperature of 25 deg C and carbon dioxide partial pressure of 0.05 to 1 at

  1. Removal of Methyl Red from Aqueous Solution by Adsorption on Treated Banana Pseudo stem Fibers Using Response Surface Method (RSM)

    International Nuclear Information System (INIS)

    Zaida Rahayu Yet; Mohd Zulkhairi Abdul Rahim

    2014-01-01

    The effect of adsorbent dose, pH and contact times on the removal of Methyl Red (MR) from aqueous solution by using agriculture waste (NaOH treated banana pseudo stem fibers) were studied. The influence of these parameters on the removal of Methyl Red was examined by using a response surface method (RSM). The experiment was conducted by combining three parameters: adsorbent dose (500-1500 mg/L), pH (2-8) dan contact time (5-75 minutes ). The Box-Behnken Design (BBD) in Response Surface Methodology (RSM) by Design Expert Version 8.0.4 (Stat Ease, USA) was used for designing the experiments. Results showed that the optimum conditions for removal of Methyl Red from an aqueous solution (100 mg/L) were as follows: adsorbent dose (1417.70 mg/L), pH (2.08) and contact time (42.94 minutes) with the value of a coefficient of determination, R2 is 98.98 %. Meanwhile, the second-order polynomial equation indicates that pH and contact times mostly affect the removal of Methyl Red. (author)

  2. γ-radiolysis of aqueous and aqueous-ethanol solutions of cobalt(3) cyanide complexes

    International Nuclear Information System (INIS)

    Kutsaev, V.G.; Potapov, I.A.; Rozenkevich, M.B.; Sakharovskij, Yu.A.; Bulgakova, G.P.; Zagorets, P.A.

    1984-01-01

    The method of stationary γ-radiolysis has been used to investigate Na 3 [Co 3 (CN) 6 ] and K 2 [Co 3 (CN) 5 H 2 O] reduction in aqueous solutions in the presence of NaCN, KCN, KCl and C 2 H 5 OH additions. [Co 2 (CN) 5 ] 3- ion is shown to be the product of reduction. Radiation-chemical yield increases in the presence of alkali metal cyanides and large quantities (10-20 vol.%) of C 2 H 5 OH. Energy consumption for radiation-chemical reduction of Co 3 cyanide complexes is 50 times lower than for photochemical one

  3. Neutron studies of paramagnetic fullerenols’ assembly in aqueous solutions

    Science.gov (United States)

    Lebedev, V. T.; Szhogina, A. A.; Suyasova, M. V.

    2018-03-01

    Recent results on structural studies of aqueous solutions of water-soluble derivatives of endofullerenes encapsulating 4f- and 3d-elements have been presented. Neutron small angle scattering experiments allowed recognize subtle features of fullerenols assembly as dependent on chemical nature (atomic number) of interior atom, pH-factor and temperature of solutions. It was observed a fractal-type fullerenols’ ordering at the scale of correlation radii ∼ 10-20 nm when molecules with iron atoms are integrated into branched structures at low concentrations (C ≤ 1 % wt.) and organized into globular aggregates at higher amounts (C > 1 % wt.). On the other hand, for Lanthanides captured in carbon cages the supramolecular structures are mostly globular and have larger gyration radii ∼ 30 nm. They demonstrated a good stability in acidic (pH ∼ 3) and neutral (pH ∼ 7) media that is important for forthcoming medical applications.

  4. Radiation chemistry of amino acids and peptides in aqueous solutions

    International Nuclear Information System (INIS)

    Simic, M.G.

    1978-01-01

    Radiation chemistry relevant to radiation preservation of high protein foods is reviewed. Some conclusions concerning the chemistry of irradiated amino acids, peptides, and proteins have been derived from product analysis of γ-irradiated solutions while the main mechanistic considerations result from the chemistry and kinetics of free radical intermediates observed by pulse radiolysis. The precursors of chemistry in not too concentrated solutions ( - , OH, and H. Their reactivity with molecules and their preference for characteristic groups within the molecule are discussed. The reviewed reactions of the model systems are accountable for a variety of radiolytic products found in irradiated foods. From detailed understanding of radiation chemistry in aqueous and frozen systems formation of many classes of compounds can be predicted or entirely eliminated in order to corroborate and extend the conclusions reached from the animal feeding experiments concerning the formation of toxic, mutagenic, and carcinogenic compounds and/or reduction of the nutritional value of foods

  5. Molecular-dynamics simulations of urea nucleation from aqueous solution.

    Science.gov (United States)

    Salvalaglio, Matteo; Perego, Claudio; Giberti, Federico; Mazzotti, Marco; Parrinello, Michele

    2015-01-06

    Despite its ubiquitous character and relevance in many branches of science and engineering, nucleation from solution remains elusive. In this framework, molecular simulations represent a powerful tool to provide insight into nucleation at the molecular scale. In this work, we combine theory and molecular simulations to describe urea nucleation from aqueous solution. Taking advantage of well-tempered metadynamics, we compute the free-energy change associated to the phase transition. We find that such a free-energy profile is characterized by significant finite-size effects that can, however, be accounted for. The description of the nucleation process emerging from our analysis differs from classical nucleation theory. Nucleation of crystal-like clusters is in fact preceded by large concentration fluctuations, indicating a predominant two-step process, whereby embryonic crystal nuclei emerge from dense, disordered urea clusters. Furthermore, in the early stages of nucleation, two different polymorphs are seen to compete.

  6. Molecular-dynamics simulations of urea nucleation from aqueous solution

    Science.gov (United States)

    Salvalaglio, Matteo; Perego, Claudio; Giberti, Federico; Mazzotti, Marco; Parrinello, Michele

    2015-01-01

    Despite its ubiquitous character and relevance in many branches of science and engineering, nucleation from solution remains elusive. In this framework, molecular simulations represent a powerful tool to provide insight into nucleation at the molecular scale. In this work, we combine theory and molecular simulations to describe urea nucleation from aqueous solution. Taking advantage of well-tempered metadynamics, we compute the free-energy change associated to the phase transition. We find that such a free-energy profile is characterized by significant finite-size effects that can, however, be accounted for. The description of the nucleation process emerging from our analysis differs from classical nucleation theory. Nucleation of crystal-like clusters is in fact preceded by large concentration fluctuations, indicating a predominant two-step process, whereby embryonic crystal nuclei emerge from dense, disordered urea clusters. Furthermore, in the early stages of nucleation, two different polymorphs are seen to compete. PMID:25492932

  7. Influence of coal properties on mercury uptake from aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Lakatos, J.; Brown, S.D.; Snape, C.E. [Miskolc University, Miskolc-Egyetemvaros (Hungary). Research Inst. of Applied Chemistry

    1999-10-01

    The uptake of mercury (II) from aqueous solution by a range of coals has been studied and the results have been compared to those for a number of other sorbents, including commercial active carbons and cation-exchange resins. At pH 5 in a buffer medium, the capacities for mercury removal of the low-rank coals and the oxidized bituminous coals investigated are comparable to those of the other sorbents tested. For the lignites investigated, a high content of organic sulfur does not markedly affect the capacity for mercury uptake in relatively neutral and low chloride media, owing to redox reactions being the most likely mechanism involved. However, in highly acidic solutions, the capacities for mercury uptake are considerably greater for the high-sulfur coals investigated than for their low-sulfur counterparts due to chelation being the major sorption process involved. 36 refs., 4 figs., 7 tabs.

  8. The pulse radiolysis of aqueous solutions of simple RCN compounds

    International Nuclear Information System (INIS)

    Draganic, I.G.; Draganic, Z.D.; Markovic, V.M.

    1976-01-01

    Fast kinetic spectrophotometry was used to study the absorption spectra of short-living intermediates produced by reactions of RCN molecules with H, esub(aq) - and OH. The spectra were obtained on the microsecond time scale after an electron pulse from a Febetron 707 accelerator in aqueous solutions of the following compounds: hydrocyanic acid, acetonitrile, propionitrile, malononitrile and succinonitrile. It has been found that all intermediates absorb in the U.V. range (lamba 9 dm 3 mol -1 s -1 . In the presence of an efficient scavenger for hydroxyl radicals, the same transient spectra were registered in acid and neutral solutions suggesting that the protonations of esub(aq) - adducts of these RCN molecules were complete within a submicrosecond time interval. (author)

  9. Ionizing radiation induced degradation of salicylic acid in aqueous solution

    Science.gov (United States)

    Albarrán, Guadalupe; Mendoza, Edith

    2018-06-01

    The radiation-induced degradation of salicylic acid (SA-) in aqueous solutions (1.0 and 0.1 mmol dm-3) saturated with N2O or air or without oxygen were studied. Irradiation was carried out using a cobalt-60 source. With a 1 mmol dm-3 solution saturated with N2O a seemingly total degradation occurred at about 18 kGy, although small quantities of 2,3-dihydroxybenzoic acid, catechol and 2,5-dihydroxybenzoic acid were present at that dose at concentrations of 67, 22 and 6 μmol dm-3 respectively. Under air and when free oxygen, the three radiolytic products were present at 18.54 kGy while SA- was destroyed only to 90% and 62%, respectively. In the case of 0.1 mmol dm-3 SA- solutions, the acid was degraded at 3.5 kGy if the solution contained N2O, at 5.8 kGy in air and at 7 kGy without oxygen. The concentration of the radiolytic products increased with increasing dose and after a maximum they decreased. The oxidation was followed by measuring the chemical oxygen demand; the slopes were 0.48 and 0.11, 0.21 and 0.07, 0.15 and 0.03 mmol dm-3 kGy-1 for 1.0 and 0.10 mmol dm-3 solutions saturated with N2O or air or without oxygen, respectively.

  10. Radiation crosslinking of methylcellulose and hydroxyethylcellulose in concentrated aqueous solutions

    International Nuclear Information System (INIS)

    Wach, Radoslaw A.; Mitomo, Hiroshi; Nagasawa, Naotsugu; Yoshii, Fumio

    2003-01-01

    The effects of ionizing radiation on aqueous solutions of cellulose ethers, methylcellulose (MC) and hydroxyethylcellulose (HEC) were investigated. The well-established knowledge states that cellulose and its derivatives belong to degrading type of polymers. However, in our study intermolecular crosslinking initiated by gamma rays or electron beam leaded to the formation of insoluble gel. This is an opposite effect of irradiation to the degradation. Paste-like form of the initial specimen, i.e. concentration 20-30%, when water plasticizes the bulk of polymer; and a high dose rate were favorable for hydrogel formation. Gel fraction up to 60% and 70% was obtained from solutions of HEC and MC, respectively. Produced hydrogels swell markedly in aqueous media by imbibing and holding the solvent. Radiation parameters of irradiation, such as yields of degradation and crosslinking and the gelation dose, were evaluated by sol-gel analysis on the basis of Charlesby-Rosiak equation. Despite of the crosslinked structure, obtained hydrogels can be included into the group of biodegradable materials. They undergo decomposition by the action of cellulase enzyme or microorganisms from compost

  11. Solar photo-Fenton mineralization of antipyrine in aqueous solution.

    Science.gov (United States)

    Durán, A; Monteagudo, J M; Sanmartín, I; Carrasco, A

    2013-11-30

    The mineralization of an aqueous solution of antipyrine (C11H12N2O), an emerging contaminant, using a solar photocatalytic oxidation process assisted with ferrioxalate was evaluated in a compound parabolic collector (CPC) pilot plant. Under the selected operating conditions ([H2O2] = 250 ppm, [Fe] = 14 ppm, pH = 2.7, and [(COOH)2·2H2O] = 80 ppm), 60% of TOC is removed just 5 min after treating an aqueous solution containing 50 ppm of antipyrine. The addition of oxalic acid up to a maximum concentration of 80 ppm significantly increases the mineralization rate during the first 15 min of the reaction. The synergism between the solar and dark H2O2/ferrioxalate process was quantified at 79%, calculated from the pseudo first-order mineralization rate constants. The operational costs due to the consumption of electrical energy, reagents and catalysts were calculated from the optimal conditions and compared with a novel sono-photocatalytic process using artificial UV-light. The results showed that the ferrioxalate-assisted solar photo-Fenton process was economically feasible, being able to achieve up to 60% mineralization with a total cost of 4.5 cent €/g TOC removed (1.1 €/m(3)). Copyright © 2013 Elsevier Ltd. All rights reserved.

  12. Complex formation in aqueous trimethylamine-N-oxide (TMAO) solutions.

    Science.gov (United States)

    Hunger, Johannes; Tielrooij, Klaas-Jan; Buchner, Richard; Bonn, Mischa; Bakker, Huib J

    2012-04-26

    We study aqueous solutions of the amphiphilic osmolyte trimethylamine-N-oxide (TMAO) using broadband dielectric spectroscopy and femtosecond mid-infrared spectroscopy. Both experiments provide strong evidence for distinctively slower rotation dynamics for water molecules interacting with the hydrophobic part of the TMAO molecules. Further, water is found to interact more strongly at the hydrophilic site of the TMAO molecules: we find evidence for the formation of stable, TMAO·2H2O and/or TMAO·3H2O complexes. While this coordination structure seems obvious, the lifetime of these complexes is found to be extraordinarily long (>50 ps). The existence of these long-lived complexes leads to pronounced parallel dipole correlations between water and TMAO, reflected in enhanced amplitudes in the dielectric spectra. The strong interaction between water and TMAO also results in a red-shifted band for the O-D stretching vibration of HDO molecules in an isotopically diluted aqueous TMAO solution. This O-D stretching vibration has a vibrational lifetime of 670 fs, which is significantly shorter than the lifetime of the O-D stretch vibration of bulk-like HDO molecules, presumably due to efficient coupling to vibrational modes of TMAO. The rotational dynamics of these O-D groups are slowed down dramatically, and are limited by the rotation of the whole complex, while the O-D vector oriented away from TMAO probably shows an accelerated reorientation.

  13. Chemical dosimetry by UV spectrophotometry of aqueous ascorbic acid solutions

    International Nuclear Information System (INIS)

    Alian, A.; El-Assay, N.B.; Abdel-Rehim, F.; Amin, N.E.; McLaughlin, W.L.; Roushdy, H.

    1984-01-01

    The decrease in the ultraviolet absorption of aqueous solutions of ascorbic acid brought about by large doses of gamma radiation has been investigated as a means of developing a new chemical dosimeter. Because of spontaneous ring opening under various conditions after dissolution in water, some additives were examined as possible stabilizers against such denaturing of aqueous ascorbic acid. At an ascorbic acid concentration of 10 -4 M, either 1 to 2% glycine or 0.2 M NaCl was found to be a good stabilizer. A mechanism of radiation chemistry has been proposed based on hydroxyl radical and hydroxyl adduct intermediates, leading to dehydroascorbic acid through the ascorbate complex. The optimum dosimeter solution covers an absorbed dose range approx. 50 to 350 Gy, when measured at 264 nm wavelength. The G-values for dehydroascorbic acid production were determined to be 2.94 +- 0.33 and 2.43 +- 0.11 (100 eV) -1 , with glycine and NaCl used respectively as stabilizers. (author)

  14. Radiolysis of titanium potassium oxalate in aqueous solution. [. gamma. rays

    Energy Technology Data Exchange (ETDEWEB)

    Bundo, Y; Ono, I [Industrial Research Inst. of Kanagawa Prefecture, Yokohama (Japan); Ogawa, T

    1975-01-01

    The dissolution state of titanium potassium oxalate in aqueous solution is different according to the pH. The yellowish brown titanium complex produced by the reaction of titanium potassium oxalate and hydrogen peroxide seems to be different in its structure according to the pH. Considering these points, gamma-ray irradiation was carried out on the sample by dissolving titanium potassium oxalate in purified water under the conditions of oxygen saturation and nitrogen saturation, and the relation between irradiation dose and the production of titanium complex was determined. On the basis of the experimental result, the mechanism of forming hydrogen peroxide was presumed. The radiation source used was 2,000 Ci of /sup 60/Co. For photometric analysis, a 139 type photoelectric spectrophotometer of Hitachi Ltd. was used. From the experimental results, in neutral water, titanium potassium oxalate exists in the state that two oxalic acid ions are coordinated to titanyl ion, while in case of the pH lowered by the addition of sulfuric acid, it can exist in the state that one oxalic acid ion is coordinated to titanyl ion. The yield of hydrogen peroxide produced by irradiating titanium potassium oxalate aqueous solution with gamma-ray is the sum of the molecular product from water and the radiolysis product from titanium potassium oxalate.

  15. Preparation of metallic nanoparticles by irradiation in starch aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Nemţanu, Monica R., E-mail: monica.nemtanu@inflpr.ro; Braşoveanu, Mirela, E-mail: monica.nemtanu@inflpr.ro; Iacob, Nicuşor, E-mail: monica.nemtanu@inflpr.ro [National Institute for Lasers, Plasma and Radiation Physics, Electron Accelerators Laboratory, 409 Atomiştilor St., PO Box MG-36, 077125, Bucharest-Măgurele (Romania)

    2014-11-24

    Colloidal silver nanoparticles (AgNPs) were synthesized in a single step by electron beam irradiation reduction of silver ions in aqueous solution containing starch. The nanoparticles were characterized by spectrophotocolorimetry and compared with those obtained by chemical (thermal) reduction method. The results showed that the smaller sizes of AgNPs were prepared with higher yields as the irradiation dose increased. The broadening of particle size distribution occurred by increasing of irradiation dose and dose rate. Chromatic parameters such as b* (yellow-blue coordinate), C* (chroma) and ΔE{sub ab} (total color difference) could characterize the nanoparticles with respect of their concentration. Hue angle h{sup o} was correlated to the particle size distribution. Experimental data of the irradiated samples were also subjected to factor analysis using principal component extraction and varimax rotation in order to reveal the relation between dependent variables and independent variables and to reduce their number. The radiation-based method provided silver nanoparticles with higher concentration and narrower size distribution than those produced by chemical reduction method. Therefore, the electron beam irradiation is effective for preparation of silver nanoparticles using starch aqueous solution as dispersion medium.

  16. Dimethoate and atrazine retention from aqueous solution by nanofiltration membranes.

    Science.gov (United States)

    Ahmad, A L; Tan, L S; Shukor, S R Abd

    2008-02-28

    In order to produce sufficient food supply for the ever-increasing human population, pesticides usage is indispensable in the agriculture sector to control crop losses. However, the effect of pesticides on the environment is very complex as undesirable transfers occur continually among different environmental sections. This eventually leads to contamination of drinking water source especially for rivers located near active agriculture practices. This paper studied the application of nanofiltration membrane in the removal of dimethoate and atrazine in aqueous solution. Dimethoate was selected as the subject of study since it is being listed as one of the pesticides in guidelines for drinking water by World Health Organization. Nevertheless, data on effectiveness of dimethoate rejection using membranes has not been found so far. Meanwhile, atrazine is classified as one of the most commonly used pesticides in Malaysia. Separation was done using a small batch-type membrane separation cell with integrated magnetic stirrer while concentration of dimethoate and atrazine in aqueous solution was analyzed using high performance liquid chromatography (HPLC). Four nanofiltration membranes NF90, NF200, NF270 and DK were tested for their respective performance to separate dimethoate and atrazine. Of all four membranes, NF90 showed the best performance in retention of dimethoate and atrazine in water.

  17. The radiation chemistry of aqueous sodium terephthalate solutions

    International Nuclear Information System (INIS)

    Matthews, R.W.

    1980-04-01

    The radiation chemistry of cobalt-60 gamma-irradiated aqueous sodium terephthalate solutions has been studied. In aerated 4 x 10 -4 M sodium hydroxide solutions, the main products are hydroxyterephthalate (HTA) (G = 0.99 +- 0.01), carbonate (G = 1.31 +- 0.08), and peroxides (G = 2.84 +- 0.04). The HTA and carbonate species are both formed as a result of hydroxyl radical attack and account for approximately 90 per cent of hydroxyl radical reactions. Oxygen needs to be present for efficient conversion of the terephthalate-OH radical adduct to HTA and oxygenation increases G(HTA) above the aerated solution value. G(HTA) is unaffected by changes in terephthalate concentration between 1 x 10 -4 M and 1 x 10 -2 M in sodium hydroxide solutions at pH 10. Decreasing the solution pH does however affect G(HTA). In phosphate buffered solutions pH 6.85, G(HTA) is 0.93 +- 0.01 and lower values are obtained with further decrease in solution pH. The lowering of the G(HTA) value is attributed to recombination reactions between the terephthalate-OH radical products and reducing radical products. Experimental evidence supporting the recombination postulate was obtained from the measurement of a parallel decrease in the peroxide yield and the observation of a dose rate effect on G(HTA). Competition kinetic studies with the added solutes carbonate and bicarbonate gave the rate ratios k (OH + TA 2- ) : k(OH + CO 3 2- ) : k(OH + HCO 3 - ) = 1 : 0.105 : 0.0036

  18. Adsorption of Chromium from Aqueous Solution Using Polyaniline

    Directory of Open Access Journals (Sweden)

    Majid Riahi Samani

    2011-10-01

    Full Text Available New group of polymers have been synthesized that are conductive of electricity so they are called conducting polymers. One of the most conducting polymers is "polyaniline". In the present study, polyaniline was synthesized by oxidizing aniline monomer under strongly acidic conditions using potassium iodate as an initiator of oxidative polymerization. Synthesized polyaniline as a powder used as an adsorbent to remove chromium from aqueous solution. Experiments were conducted in batch mode with variables such as amount of polyaniline, chromium solution pH and adsorbtion isotherms. Due to presence of Cr (III in solution after using polyaniline, removal mechanism is the combination of surface adsorption and reduction. It seems that polyaniline reduces the Cr(VI to Cr(III and adsorbs the Cr(III and a part of remaining  Cr(VI. It is well known that nitrogen atom in compounds of amine derivative makes co-ordinate bond with positive charge of metals due to the presence of electron in sp3 orbital of nitrogen. The majority of total chromium removal  occurred at 30minute for polyaniline  and the optimum  time for  hexavalent chromium  removal was about 5 min. Polyaniline has the maximum total cheomiume removal at pH, 3-9. The maximum hexavalent chromium removal occurred at acidic pH for polyanilines. The equilibrium adsorption data for polyaniline fitted both Freundlich’s and Langmuir’s isotherms. This research shows that polyaniline can be used as an adsorbent  for removal chromium from aqueous solution.

  19. Method of precipitating uranium from an aqueous solution and/or sediment

    Science.gov (United States)

    Tokunaga, Tetsu K; Kim, Yongman; Wan, Jiamin

    2013-08-20

    A method for precipitating uranium from an aqueous solution and/or sediment comprising uranium and/or vanadium is presented. The method includes precipitating uranium as a uranyl vanadate through mixing an aqueous solution and/or sediment comprising uranium and/or vanadium and a solution comprising a monovalent or divalent cation to form the corresponding cation uranyl vanadate precipitate. The method also provides a pathway for extraction of uranium and vanadium from an aqueous solution and/or sediment.

  20. Morphology evaluation of ZrO2 dip coating on mild steel and its corrosion performance in NaOH solution

    Science.gov (United States)

    Anwar, M. A.; Kurniawan, T.; Asmara, Y. P.; Harun, W. S. W.; Oumar, A. N.; Nandyanto, A. B. D.

    2017-10-01

    In this work, the morphology of ZrO2 thin film from dip coating process on mild steel has been investigated. Mild steel was dip-coated on solution made of zirconium butoxide as a precursor, ethanol as solvent, acetylacetone as chelating agent and water for hydrolysis. Number of dipping was adjusted at 3, 5 and 7 times. The dipped sample then annealed at 350°C for two hours by adjusting the heating rate at 1°C/min respectively. The optical microscope showed that micro-cracks were observed on the surface of the coating with its concentration reduced as dipping sequence increased. The XRD result showed that annealing process can produce polycrystalline tetragonal-ZrO2. Meanwhile, SEM image showed that the thicknesses of the ZrO2 coatings were in between 400-600 nm. The corrosion resistance of uncoated and coated substrates was studied by polarization test through potentio-dynamic polarization curve at 1mV/s immersed in with 3.5% NaCl. The coating efficiency was improved as the number of layer dip coated increased, which showed improvement in corrosion protection.

  1. Quenching characteristics of bathocuproinedisulfonic acid, disodium salt in aqueous solution and copper sulfate plating solution

    Science.gov (United States)

    Koga, Toshiaki; Hirakawa, Chieko; Takeshita, Michinori; Terasaki, Nao

    2018-04-01

    Bathocuproinedisulfonic acid, disodium salt (BCS) is generally used to detect Cu(I) through a color reaction. We newly found BCS fluorescence in the visible blue region in an aqueous solution. However, the fluorescence mechanism of BCS is not well known, so we should investigate its fundamental information. We confirmed that the characteristics of fluorescence are highly dependent on the molecular concentration and solvent properties. In particular, owing to the presence of the copper compound, the fluorescence intensity extremely decreases. By fluorescence quenching, we observed that a copper compound concentration of 10-6 mol/L or less could easily be measured in an aqueous solution. We also observed BCS fluorescence in copper sulfate plating solution and the possibility of detecting monovalent copper by fluorescence reabsorption.

  2. Removal of chromium and nickel ions from aqueous solution by ...

    African Journals Online (AJOL)

    The study investigated the adsorption of Cr(VI) and Ni(II) on modified coconut husk (low cost adsorbent) for the remediation of Cr(VI) and Ni(II) from some synthetic industrial waste effluents. The coconut husk was modified by mixing with 0.1 M NaOH and HCl respectively. The effects of varying adsorbent loading, hydrogen ...

  3. The movement of solutes through aqueous fissures in porous rock

    International Nuclear Information System (INIS)

    Glueckauf, E.

    1980-06-01

    A mathematical treatment has been given for the movement of materials dissolved in water flowing through narrow fissures of a micro-porous substrate. As there is no water flow in these micro-pores, equilibrium between the aqueous solution and the micro-porous substrate proceeds only by diffusion, with the result that there arises a gross disequilibrium. Two major effects arise: first, the hold-up in the substrate - even when there is no adsorption taking place - is orders of magnitude larger than on non-porous substrate, and increases even further, if adsorption takes place. Secondly, dispersion caused by non-equilibrium is also orders of magnitude greater than dispersion arising from convection effects of the water flow in interconnecting fissures. As a result, the solutes arrive very much later at the end of the underground fissures, and in concentrations which are very much lower than have been calculated in previous modelling experiments. The significance of these effects is discussed in detail, and this can be helpful in the selection of sites for underground disposal of radioactive waste. It is now quite feasible to specify sites with conditions, where even solutes with minimal adsorption would not return to the surface within a million years, and where solutes of moderately strong adsorption would be effectively immobile. (author)

  4. Radiation induced degradation of xanthan gum in aqueous solution

    Science.gov (United States)

    Hayrabolulu, Hande; Demeter, Maria; Cutrubinis, Mihalis; Güven, Olgun; Şen, Murat

    2018-03-01

    In our previous study, we have investigated the effect of gamma rays on xanthan gum in the solid state and it was determined that dose rate was an important factor effecting the radiation degradation of xanthan gum. In the present study, in order to provide a better understanding of how ionizing radiation effect xanthan gum, we have investigated the effects of ionizing radiation on aqueous solutions of xanthan at various concentrations (0.5-4%). Xanthan solutions were irradiated with gamma rays in air, at ambient temperature, at different dose rates (0.1-3.3-7.0 kGy/h) and doses (2.5-50 kGy). Change in their molecular weights was followed by size exclusion chromatography (SEC). Chain scission yield (G(S)), and degradation rate constants (k) were calculated. It was determined that, solution concentration was a factor effecting the degradation chemical yield and degradation rate of xanthan gum. Chain scission reactions were more effective for lower solution concentrations.

  5. Corrosion control of vanadium in aqueous solutions by amino acids

    International Nuclear Information System (INIS)

    El-Rabiee, M.M.; Helal, N.H.; El-Hafez, Gh.M. Abd; Badawy, W.A.

    2008-01-01

    The electrochemical behavior of vanadium in amino acid free and amino acid containing aqueous solutions of different pH was studied using open-circuit potential measurements, polarization techniques and electrochemical impedance spectroscopy (EIS). The corrosion current density, i corr , the corrosion potential, E corr and the corrosion resistance, R corr , were calculated. A group of amino acids, namely, glycine, alanine, valine, histidine, glutamic and cysteine has been investigated as environmentally safe inhibitors. The effect of Cl - on the corrosion inhibition efficiency especially in acid solutions was investigated. In neutral and basic solutions, the presence of amino acids increases the corrosion resistance of the metal. The electrochemical behavior of V before and after the corrosion inhibition process has shown that some amino acids like glutamic acid and histidine have promising corrosion inhibition efficiency at low concentration (≅25 mM). The inhibition efficiency (η) was found to depend on the structure of the amino acid and the constituents of the corrosive medium. The corrosion inhibition process is based on the adsorption of the amino acid molecules on the metal surface and the adsorption process follows the Freundlich isotherm. The adsorption free energy for valine on V in acidic solutions was found to be -9.4 kJ/mol which reveals strong physical adsorption of the amino acid molecules on the vanadium surface

  6. On the state of phosphomolybdenovanadic heteropolyblue in aqueous solutions

    International Nuclear Information System (INIS)

    Kuznetsova, L.I.; Yurchenko, Eh.N.; Maksimovskaya, R.I.; Kirik, N.P.; Matveev, K.I.

    1977-01-01

    The effect has been investigated of pH solution on the state of the phosphomolybdenovanadic heteropolyblues of the 12. series, containing n=1,2,3,6 atoms of vanadium (6). It has been shown that the free VO 2+ intrusion into the sphere of heteropolyanions takes place alongside with pH increasing from 1 to 3. At the some time the rate of oxidation of the heteropolyblue solutions by oxygen and the optical density of solutions increase too. The dissociation constants of the heteropolyblue molecule in acid medium increase with increasing of the quantity of vanadium atoms. It has been shown that stability of heteropolyblue in relation to molybdenum decreases with increasing of its quantity in the heteropolyblue molecule. Using precipitation of the heteropolyanions by the cation of tetraethyl ammonium, it has been shown that heteropolyanions can consist of 1,2,3 and 6 atoms of V(6). The state of heteropolyblues in an aqueous solution is characterized by electron absorption spectra

  7. Coupled jump rotational dynamics in aqueous nitrate solutions.

    Science.gov (United States)

    Banerjee, Puja; Yashonath, Subramanian; Bagchi, Biman

    2016-12-21

    A nitrate ion (NO 3 - ) with its trigonal planar geometry and charges distributed among nitrogen and oxygen atoms can couple to the extensive hydrogen bond network of water to give rise to unique dynamical characteristics. We carry out detailed atomistic simulations and theoretical analyses to investigate these aspects and report certain interesting findings. We find that the nitrate ions in aqueous potassium nitrate solution exhibit large amplitude rotational jump motions that are coupled to the hydrogen bond rearrangement dynamics of the surrounding water molecules. The jump motion of nitrate ions bears certain similarities to the Laage-Hynes mechanism of rotational jump motions of tagged water molecules in neat liquid water. We perform a detailed atomic-level investigation of hydrogen bond rearrangement dynamics of water in aqueous KNO 3 solution to unearth two distinct mechanisms of hydrogen bond exchange that are instrumental to promote these jump motions of nitrate ions. As observed in an earlier study by Xie et al., in the first mechanism, after breaking a hydrogen bond with nitrate ion, water forms a new hydrogen bond with a water molecule, whereas the second mechanism involves just a switching of hydrogen bond between the two oxygen atoms of the same nitrate ion (W. J. Xie et al., J. Chem. Phys. 143, 224504 (2015)). The magnitude as well as nature of the reorientational jump of nitrate ion for the two mechanisms is different. In the first mechanism, nitrate ion predominantly undergoes out-of-plane rotation, while in the second mechanism, in-plane reorientation of NO 3 - is favourable. These have been deduced by computing the torque on the nitrate ion during the hydrogen bond switching event. We have defined and computed the time correlation function for coupled reorientational jump of nitrate and water and obtained the associated relaxation time which is also different for the two mechanisms. These results provide insight into the relation between the

  8. Pulse Radiolysis of Aqueous Solutions of Aniline and Substituted Anilines

    Energy Technology Data Exchange (ETDEWEB)

    Christensen, H C

    1971-07-01

    The primary reactions of hydrated electrons, hydrogen atoms and hydroxyl radicals with aniline and the aniline cation in aqueous solutions have been studied by the technique of pulse radiolysis and by determination of end products after y-radiolysis. Hydrogen atoms and hydrated electrons react with aniline under formation of the cyclohexadienyl type radical with absorption maximum at 355 nm and an extinction coefficient of 4100/M/cm. A similar radical formed by reaction of hydrogen atoms with the aniline cation has its absorption maximum at 31 0 nm and an extinction coefficient of 3200/M/cm. Hydrogen atoms react with the acid and neutral forms of aniline with rate constants of (1.3 +- 0.2 ) x 109/M/s and (2.9 +- 0.7) x 109/M/s, respectively. OH radicals react with aniline with a rate constant of (1.4 +- 0.3) x 1010/M/s under formation of the cyclohexadienyl radical with absorption maximum at 355 nm and the anilino radical with absorption maxima at 300 and 400 nm. The cyclohexadienyl radical decayed in a first order process with a rate constant of 1.4 x 105/s by elimination of NH{sub 3}, whereas the anilino radical disappeared in a second order reaction under formation of hydrazobenzene. O- radicals react with aniline at pH 13.3 with a rate constant of (3.1 +- 0.6) x 109 under formation of anilino radicals. The reaction of OH radicals with the aniline cation produced the anilino radical cation with a rate constant of (4.8 +- 0.8) x 109 . The absorption maximum was placed at 415 nm, The cyclohexadienyl type radical with absorption maximum at 350 nm was also found in aqueous solutions of 2-amino-1,3-dimethylbenzene but was not formed in solutions of N,N' -dimethylaniline

  9. Pulse Radiolysis of Aqueous Solutions of Aniline and Substituted Anilines

    International Nuclear Information System (INIS)

    Christensen, H.C.

    1971-01-01

    The primary reactions of hydrated electrons, hydrogen atoms and hydroxyl radicals with aniline and the aniline cation in aqueous solutions have been studied by the technique of pulse radiolysis and by determination of end products after y-radiolysis. Hydrogen atoms and hydrated electrons react with aniline under formation of the cyclohexadienyl type radical with absorption maximum at 355 nm and an extinction coefficient of 4100/M/cm. A similar radical formed by reaction of hydrogen atoms with the aniline cation has its absorption maximum at 31 0 nm and an extinction coefficient of 3200/M/cm. Hydrogen atoms react with the acid and neutral forms of aniline with rate constants of (1.3 ± 0.2 ) x 10 9 /M/s and (2.9 ± 0.7) x 10 9 /M/s, respectively. OH radicals react with aniline with a rate constant of (1.4 ± 0.3) x 10 10 /M/s under formation of the cyclohexadienyl radical with absorption maximum at 355 nm and the anilino radical with absorption maxima at 300 and 400 nm. The cyclohexadienyl radical decayed in a first order process with a rate constant of 1.4 x 10 5 /s by elimination of NH 3 , whereas the anilino radical disappeared in a second order reaction under formation of hydrazobenzene. O - radicals react with aniline at pH 13.3 with a rate constant of (3.1 ± 0.6) x 10 9 under formation of anilino radicals. The reaction of OH radicals with the aniline cation produced the anilino radical cation with a rate constant of (4.8 ± 0.8) x 10 9 . The absorption maximum was placed at 415 nm, The cyclohexadienyl type radical with absorption maximum at 350 nm was also found in aqueous solutions of 2-amino-1,3-dimethylbenzene but was not formed in solutions of N,N' -dimethylaniline

  10. LASERS, ACTIVE MEDIA: The aqueous-polyelectrolyte dye solution as an active laser medium

    Science.gov (United States)

    Akimov, A. I.; Saletskii, A. M.

    2000-11-01

    The spectral, luminescent, and lasing properties of aqueous solutions of a cationic dye rhodamine 6G with additions of anion polyelectrolytes — polyacrylic and polymethacrylic acids — are studied. It is found that the energy and spectral properties of lasing of these solutions depend on the ratio of concentrations of polyelectrolyte and molecules. It is also found that the lasing parameters of aqueous-polyelectrolyte dye solutions can be controlled by changing the structure of the molecular system. The variation in the structure of aqueous-polyelectrolyte dye solutions of rhodamine 6G resulted in an almost five-fold increase in the lasing efficiency compared to that in aqueous dye solutions.

  11. Forced Spreading of Aqueous Solutions on Zwitterionic Sulfobetaine Surfaces for Rapid Evaporation and Solute Separation.

    Science.gov (United States)

    Wu, Cyuan-Jhang; Singh, Vickramjeet; Sheng, Yu-Jane; Tsao, Heng-Kwong

    2017-08-01

    Solute separation of aqueous mixtures is mainly dominated by water vaporization. The evaporation rate of an aqueous drop grows with increasing the liquid-gas interfacial area. The spontaneous spreading behavior of a water droplet on a total wetting surface provides huge liquid-gas interfacial area per unit volume; however, it is halted by the self-pinning phenomenon upon addition of nonvolatile solutes. In this work, it is shown that the solute-induced self-pinning can be overcome by gravity, leading to anisotropic spreading much faster than isotropic spreading. The evaporation rate of anisotropic spreading on a zwitterionic sulfobetaine surface is 25 times larger as that on a poly(methyl methacrylate) surface. Dramatic enhancement of evaporation is demonstrated by simultaneous formation of fog atop liquid film. During anisotropic spreading, the solutes are quickly precipitated out within 30 s, showing the rapid solute-water separation. After repeated spreading process for the dye-containing solution, the mean concentration of the collection is doubled, revealing the concentration efficiency as high as 100%. Gravity-enhanced spreading on total wetting surfaces at room temperature is easy to scale-up with less energy consumption, and thus it has great potentials for the applications of solute separation and concentration.

  12. Iron(III) citrate speciation in aqueous solution.

    Science.gov (United States)

    Silva, Andre M N; Kong, XiaoLe; Parkin, Mark C; Cammack, Richard; Hider, Robert C

    2009-10-28

    Citrate is an iron chelator and it has been shown to be the major iron ligand in the xylem sap of plants. Furthermore, citrate has been demonstrated to be an important ligand for the non-transferrin bound iron (NTBI) pool occurring in the plasma of individuals suffering from iron-overload. However, ferric citrate chemistry is complicated and a definitive description of its aqueous speciation at neutral pH remains elusive. X-Ray crystallography data indicates that the alcohol function of citrate (Cit4-) is involved in Fe(III) coordination and that deprotonation of this functional group occurs upon complex formation. The inability to include this deprotonation in the affinity constant calculations has been a major source of divergence between various reports of iron(III)-citrate affinity constants. However the recent determination of the alcoholic pKa of citric acid (H4Cit) renders the reassessment of the ferric citrate system possible. The aqueous speciation of ferric citrate has been investigated by mass spectrometry and EPR spectroscopy. It was observed that the most relevant species are a monoiron dicitrate species and dinuclear and trinuclear oligomeric complexes, the relative concentration of which depends on the solution pH value and the iron : citric acid molar ratio. Spectrophotometric titration was utilized for affinity constant determination and the formation constant for the biologically relevant [Fe(Cit)2]5- is reported for the first time.

  13. Arsenic Removal from Aqueous Solutions by Salvadora persica Stem Ash

    Directory of Open Access Journals (Sweden)

    Ferdos Kord Mostafapour

    2013-01-01

    Full Text Available Arsenic is a naturally occurring metalloid, which is widely distributed in nature and is regarded as the largest mass poisoning in history. In the present study, the adsorption potential of Salvadora persica (S. persica stem ash in a batch system for the removal of As(V from aqueous solutions was investigated. Isotherm studies were carried out to evaluate the effect of contact time (20–240 min, pH (2–11, initial arsenic concentration (50–500 μg/L, and adsorbent dose on sorption efficiency. Maximum removal efficiency of 98.33% and 99.32% was obtained at pH 6, adsorbent dosage 3.5 g/L, initial As(V concentration 500 μg/L, and contact time 80 and 60 min for S. persica stem ash at 300 °C and 500 °C, respectively. Also, the adsorption equilibriums were analyzed by the Langmuir and Freundlich isotherm models. Such equilibriums showed that the adsorption data was well fitted with the Freundlich isotherm model for S. persica stem ash at both 300 °C and 500 °C (R2=0.8983 and 0.9274, resp.. According to achieved results, it was defined that S. persica stem ash can be used effectively for As(V removal from the aqueous environment.

  14. Chemical metallization of KMPR photoresist polymer in aqueous solutions

    Science.gov (United States)

    Zeb, Gul; Duong, Xuan Truong; Vu, Ngoc Pi; Phan, Quang The; Nguyen, Duc Tuong; Ly, Viet Anh; Salimy, Siamak; Le, Xuan Tuan

    2017-06-01

    While conventional methods for preparing thin films of metals and metallic alloys on insulating substrates in the field of microelectromechanical systems (MEMS) include vapor deposition techniques, we demonstrate here that electroless deposition can be considered as an alternate efficient approach to metallize the surface of insulating substrates, such as KMPR epoxy photoresist polymer. In comparison with the physical and chemical vapor deposition methods, which are well-established for metallization of photoresist polymers, our electroless nickel plating requires only immersing the substrates into aqueous solutions in open air at low temperatures. Thin films of nickel alloy have been deposited electrolessly on KMPR surface, through a cost-effective and environmental chromium-free process, mediated through direct grafting of amine palladium complexes in aqueous medium. This covalent organic coating provides excellent adhesion between KMPR and the nickel film and allows better control of the palladium catalyst content. Covalent grafting and characterization of the deposited nickel film have been carried out by means of Fourier-transform infrared spectroscopy, scanning electron microscopy, energy-dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy techniques.

  15. Osmotic potential calculations of inorganic and organic aqueous solutions over wide solute concentration levels and temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Cochrane, T. T., E-mail: agteca@hotmail.com [AGTECA S.A., 230 Oceanbeach Road, Mount Maunganui, Tauranga 3116 (New Zealand); Cochrane, T. A., E-mail: tom.cochrane@canterbury.ac.nz [Department of Civil and Natural Resources Engineering, University of Canterbury, Private Bag 4800, Christchurch 8140 (New Zealand)

    2016-01-15

    Purpose: To demonstrate that the authors’ new “aqueous solution vs pure water” equation to calculate osmotic potential may be used to calculate the osmotic potentials of inorganic and organic aqueous solutions over wide ranges of solute concentrations and temperatures. Currently, the osmotic potentials of solutions used for medical purposes are calculated from equations based on the thermodynamics of the gas laws which are only accurate at low temperature and solute concentration levels. Some solutions used in medicine may need their osmotic potentials calculated more accurately to take into account solute concentrations and temperatures. Methods: The authors experimented with their new equation for calculating the osmotic potentials of inorganic and organic aqueous solutions up to and beyond body temperatures by adjusting three of its factors; (a) the volume property of pure water, (b) the number of “free” water molecules per unit volume of solution, “N{sub f},” and (c) the “t” factor expressing the cooperative structural relaxation time of pure water at given temperatures. Adequate information on the volume property of pure water at different temperatures is available in the literature. However, as little information on the relative densities of inorganic and organic solutions, respectively, at varying temperatures needed to calculate N{sub f} was available, provisional equations were formulated to approximate values. Those values together with tentative t values for different temperatures chosen from values calculated by different workers were substituted into the authors’ equation to demonstrate how osmotic potentials could be estimated over temperatures up to and beyond bodily temperatures. Results: The provisional equations formulated to calculate N{sub f}, the number of free water molecules per unit volume of inorganic and organic solute solutions, respectively, over wide concentration ranges compared well with the calculations of N{sub f

  16. Osmotic potential calculations of inorganic and organic aqueous solutions over wide solute concentration levels and temperatures

    International Nuclear Information System (INIS)

    Cochrane, T. T.; Cochrane, T. A.

    2016-01-01

    Purpose: To demonstrate that the authors’ new “aqueous solution vs pure water” equation to calculate osmotic potential may be used to calculate the osmotic potentials of inorganic and organic aqueous solutions over wide ranges of solute concentrations and temperatures. Currently, the osmotic potentials of solutions used for medical purposes are calculated from equations based on the thermodynamics of the gas laws which are only accurate at low temperature and solute concentration levels. Some solutions used in medicine may need their osmotic potentials calculated more accurately to take into account solute concentrations and temperatures. Methods: The authors experimented with their new equation for calculating the osmotic potentials of inorganic and organic aqueous solutions up to and beyond body temperatures by adjusting three of its factors; (a) the volume property of pure water, (b) the number of “free” water molecules per unit volume of solution, “N f ,” and (c) the “t” factor expressing the cooperative structural relaxation time of pure water at given temperatures. Adequate information on the volume property of pure water at different temperatures is available in the literature. However, as little information on the relative densities of inorganic and organic solutions, respectively, at varying temperatures needed to calculate N f was available, provisional equations were formulated to approximate values. Those values together with tentative t values for different temperatures chosen from values calculated by different workers were substituted into the authors’ equation to demonstrate how osmotic potentials could be estimated over temperatures up to and beyond bodily temperatures. Results: The provisional equations formulated to calculate N f , the number of free water molecules per unit volume of inorganic and organic solute solutions, respectively, over wide concentration ranges compared well with the calculations of N f using recorded

  17. Radiolysis of Aqueous Benzene Solutions at higher temperatures

    International Nuclear Information System (INIS)

    Christensen, H.

    1964-07-01

    Aqueous solutions of benzene have been irradiated with Co γ-rays with doses of up to 2.3 Mrad in the temperature region 100 - 200 C. At 100 C a linear relationship between the phenol concentration and the absorbed dose was obtained, but at 150 C and at higher temperatures the rate of the phenol formation increased significantly after an initial constant period. With higher doses the rate decreased again, falling almost to zero at 200 C after a dose of 2.2 Mrad. The G value of phenol in the initial linear period increased from 2.8 at 100 C to 8.0 at 200 C. The reaction mechanism is discussed and reactions constituting a chain reaction are suggested. The result of the addition of iron ions and of a few inorganic oxides to the system is presented and briefly discussed

  18. Radiation-induced degradation of 4-chloroaniline in aqueous solution

    International Nuclear Information System (INIS)

    Sanchez, M.; Wolfger, H.; Getoff, N.

    2002-01-01

    The radiation-induced decomposition of 4-chloroaniline (4-ClA) was studied under steady-state conditions using aqueous solutions saturated with air, pure oxygen, N 2 O, argon and argon in the presence of t-Butanol. Using HPLC-method, the initial G-values of the substrate degradation as well as of a number of radiolytic products were determined. The formation of aminophenols, chlorophenols, aniline and phenol in addition to chloride, ammonia, formaldehyde and mixture of aldehydes as well as carboxylic acids was studied as a function of absorbed dose. Based on the experimental data, probable reaction mechanisms for the degradation of 4-ClA by γ-rays and the formation of the identified products are presented

  19. Paracetamol degradation in aqueous solution by non-thermal plasma

    Science.gov (United States)

    Baloul, Yasmine; Aubry, Olivier; Rabat, Hervé; Colas, Cyril; Maunit, Benoît; Hong, Dunpin

    2017-08-01

    This study deals with paracetamol degradation in water using a non-thermal plasma (NTP) created by a dielectric barrier discharge (DBD). The effects of the NTP operating conditions on the degradation were studied, showing that the treatment efficiency of the process was highly dependent on the electrical parameters and working gas composition in the reactor containing the aqueous solution. A conversion rate higher than 99% was reached with an energy yield of 12 g/kWh. High resolution mass spectrometry (HRMS) measurements showed that the main species produced in water during the process were nitrogen compounds, carboxylic acids and aromatic compounds. Contribution to the topical issue "The 15th International Symposium on High Pressure Low Temperature Plasma Chemistry (HAKONE XV)", edited by Nicolas Gherardi and Tomáš Hoder

  20. Partial molar volume of anionic polyelectrolytes in aqueous solution.

    Science.gov (United States)

    Salamanca, Constain; Contreras, Martín; Gamboa, Consuelo

    2007-05-15

    In this work the partial molar volumes (V) of different anionic polyelectrolytes and hydrophobically modified polyelectrolytes (PHM) were measured. Polymers like polymaleic acid-co-styrene, polymaleic acid-co-1-olefin, polymaleic acid-co-vinyl-2-pyrrolidone, and polyacrylic acid (abbreviated as MAS-n, PA-n-K2, AMVP, and PAA, respectively) were employed. These materials were investigated by density measurements in highly dilute aqueous solutions. The molar volume results allow us to discuss the effect of the carboxylic groups and the contributions from the comonomeric principal chain. The PAA presents the smaller V, while the largest V value was for AMVP. The V of PHM shows a linear relationship with the number of methylene groups in the lateral chain. It is found that the magnitude of the contribution per methylene group decreases as the hydrophobic character of the environment increases.

  1. Radiation-induced degradation of chlorophenols in aqueous solution

    International Nuclear Information System (INIS)

    Hu Jun; Wang Jianlong

    2005-01-01

    Radiation processing is a promising technology for applications in environmental protection, which includes wastewater treatment, micro-polluted drinking water treatment and the treatment of industrial wastewater containing various toxic and nonbiodegradable pollutants, municipal sewage and sludge disinfection, and flue gas desulfuration, etc. The paper reviews manly the recent progresses in radiolysis of chlorinated phenols in aqueous solution. Advantages and existing problems of the method in this particular application ar discussed. Mechanisms of radiation-induced degradation of chlorophenols, and the factors affecting the degradation efficiency, are discussed, too. It is concluded that combined approaches, such ozone oxidation and other methods, are of great help to the radiation processing application, in terms of lowering down the dose and increasing the efficient of pollutant removal. (authors)

  2. Pulse radiolysis of Triton X-100 aqueous solution

    International Nuclear Information System (INIS)

    Perkowski, J.; Mayer, J.

    1990-01-01

    Pulse radiolysis of deaerated aqueous solutions of 4 · 10 -5 -2.4 · 10 -3 mol · dm -3 Triton X-100 gives rise to a transient species originating from the reactions of OH radicals and H atoms. The rate constants of these reactions were found to be 8.8 · 10 9 mol -1 · dm 3 · s -1 and 1.25 · 10 9 mol -1 · dm 3 · s -1 , respectively, for Triton X-100 concentrations below CMC. The corresponding transient species were found to decay according to second order kinetics. The mechanism of the reactions, including concentration effects is discussed. (author) 18 refs.; 3 figs

  3. Photo-degradation behaviour of roseoflavin in some aqueous solutions

    International Nuclear Information System (INIS)

    Tyagi, A.; Penzkofer, A.; Mathes, T.; Hegemann, P.

    2010-01-01

    An absorption and emission spectroscopic characterization of roseoflavin (8-dimethylamino-8-demethyl-riboflavin, RoF) in aqueous solutions was carried out. The studies were concentrated on roseoflavin in pH 8 phosphate buffer. Absorption cross-section spectra, fluorescence excitation spectra, fluorescence quantum distributions, fluorescence quantum yields and fluorescence lifetimes were determined. The fluorescence of RoF is quenched by photo-induced intra-molecular charge-transfer at room temperature. The photo-degradation of RoF in un-buffered water, in Tris-HCl buffer, and in phosphate buffer was studied. Phosphate buffer and to a smaller extent Tris buffer catalyse the RoF photo-degradation. Photo-excitation of the primary photoproduct, 8-methylamino-riboflavin (8-MNH-RF), enhanced the RoF degradation by triplet 8-MNH-RF - singlet RoF excitation transfer with subsequent triplet-state RoF degradation.

  4. Photo-degradation behaviour of roseoflavin in some aqueous solutions

    Science.gov (United States)

    Tyagi, A.; Penzkofer, A.; Mathes, T.; Hegemann, P.

    2010-03-01

    An absorption and emission spectroscopic characterization of roseoflavin (8-dimethylamino-8-demethyl-riboflavin, RoF) in aqueous solutions was carried out. The studies were concentrated on roseoflavin in pH 8 phosphate buffer. Absorption cross-section spectra, fluorescence excitation spectra, fluorescence quantum distributions, fluorescence quantum yields and fluorescence lifetimes were determined. The fluorescence of RoF is quenched by photo-induced intra-molecular charge-transfer at room temperature. The photo-degradation of RoF in un-buffered water, in Tris-HCl buffer, and in phosphate buffer was studied. Phosphate buffer and to a smaller extent Tris buffer catalyse the RoF photo-degradation. Photo-excitation of the primary photoproduct, 8-methylamino-riboflavin (8-MNH-RF), enhanced the RoF degradation by triplet 8-MNH-RF - singlet RoF excitation transfer with subsequent triplet-state RoF degradation.

  5. Degradation of malachite green in aqueous solution by Fenton process.

    Science.gov (United States)

    Hameed, B H; Lee, T W

    2009-05-30

    In this study, advanced oxidation process utilizing Fenton's reagent was investigated for degradation of malachite green (MG). The effects of different reaction parameters such as the initial MG concentration, initial pH, the initial hydrogen peroxide concentration, the initial ferrous concentration and the reaction temperature on the oxidative degradation of MG have been investigated. The optimal reacting conditions were experimentally found to be pH 3.40, initial hydrogen peroxide concentration=0.50mM and initial ferrous concentration=0.10mM for initial MG concentration of 20mg/L at 30 degrees C. Under optimal conditions, 99.25% degradation efficiency of dye in aqueous solution was achieved after 60 min of reaction.

  6. Conformation of poly(γ-glutamic acid) in aqueous solution.

    Science.gov (United States)

    Muroga, Yoshio; Nakaya, Asami; Inoue, Atsuki; Itoh, Daiki; Abiru, Masaya; Wada, Kaori; Takada, Masako; Ikake, Hiroki; Shimizu, Shigeru

    2016-04-01

    Local conformation and overall conformation of poly(γ-DL-glutamic acid) (PγDLGA) and poly(γ-L-glutamic acid) (PγLGA) in aqueous solution was studied as a function of degree of ionization ε by (1) H-NMR, circular dichroism, and potentiometric titration. It was clarified that their local conformation is represented by random coil over an entire ε range and their overall conformation is represented by expanded random-coil in a range of ε > ε(*) , where ε(*) is about 0.3, 0.35, 0.45, and 0.5 for added-salt concentration of 0.02M, 0.05M, 0.1M, and 0.2M, respectively. In a range of ε acidic media. © 2015 Wiley Periodicals, Inc.

  7. Photo-degradation behaviour of roseoflavin in some aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Tyagi, A. [Institut II - Experimentelle und Angewandte Physik, Universitaet Regensburg, Universitaetsstrasse 31, D-93053 Regensburg (Germany); Penzkofer, A., E-mail: alfons.penzkofer@physik.uni-regensburg.de [Institut II - Experimentelle und Angewandte Physik, Universitaet Regensburg, Universitaetsstrasse 31, D-93053 Regensburg (Germany); Mathes, T.; Hegemann, P. [Institut fuer Biologie/Experimentelle Biophysik, Humboldt Universitaet zu Berlin, Invalidenstrasse 42, D-10115 Berlin (Germany)

    2010-03-24

    An absorption and emission spectroscopic characterization of roseoflavin (8-dimethylamino-8-demethyl-riboflavin, RoF) in aqueous solutions was carried out. The studies were concentrated on roseoflavin in pH 8 phosphate buffer. Absorption cross-section spectra, fluorescence excitation spectra, fluorescence quantum distributions, fluorescence quantum yields and fluorescence lifetimes were determined. The fluorescence of RoF is quenched by photo-induced intra-molecular charge-transfer at room temperature. The photo-degradation of RoF in un-buffered water, in Tris-HCl buffer, and in phosphate buffer was studied. Phosphate buffer and to a smaller extent Tris buffer catalyse the RoF photo-degradation. Photo-excitation of the primary photoproduct, 8-methylamino-riboflavin (8-MNH-RF), enhanced the RoF degradation by triplet 8-MNH-RF - singlet RoF excitation transfer with subsequent triplet-state RoF degradation.

  8. Radiolysis of Aqueous Benzene Solutions at higher temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Christensen, H

    1964-07-15

    Aqueous solutions of benzene have been irradiated with Co {gamma}-rays with doses of up to 2.3 Mrad in the temperature region 100 - 200 C. At 100 C a linear relationship between the phenol concentration and the absorbed dose was obtained, but at 150 C and at higher temperatures the rate of the phenol formation increased significantly after an initial constant period. With higher doses the rate decreased again, falling almost to zero at 200 C after a dose of 2.2 Mrad. The G value of phenol in the initial linear period increased from 2.8 at 100 C to 8.0 at 200 C. The reaction mechanism is discussed and reactions constituting a chain reaction are suggested. The result of the addition of iron ions and of a few inorganic oxides to the system is presented and briefly discussed.

  9. Infrared spectroscopy for monitoring gas hydrates in aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Dobbs, G.T.; Luzinova, Y.; Mizaikoff, B. [Georgia Inst. of Technology, Atlanta, GA (United States). School of Chemistry and Biochemistry; Raichlin, Y.; Katzir, A. [Tel-Aviv Univ., Tel-Aviv (Israel). Shool of Physics and Astronomy

    2008-07-01

    This paper introduced the first principles for monitoring gas hydrate formation and dissociation in aqueous solution by evaluating state-responsive infrared (IR) absorption features of water with fiberoptic evanescent field spectroscopy. A first order linear functional relationship was also derived according to Lambert Beer's law in order to quantify the percentage gas hydrate within the volume of water probed via the evanescent field. In addition, spectroscopic studies evaluating seafloor sediments collected from a gas hydrate site in the Gulf of Mexico revealed minimal spectral interferences from sediment matrix components. As such, evanescent field sensing strategies were established as a promising perspective for monitoring the dynamics of gas hydrates in oceanic environments. 21 refs., 5 figs.

  10. Ionic conductivity in aqueous solutions: deuterium isotope effect

    International Nuclear Information System (INIS)

    Samanta, Alok; Ghosh, Swapan K.

    1997-01-01

    A simple theoretical investigation of the calculation of ionic conductivity in aqueous solution is presented. The dipolar hard sphere model for the solvent which has been successful elsewhere has been employed here and it has been possible to reproduce the experimental results quite accurately for both water and heavy water using only two parameters. In a more detailed theoretical approach one should employ better models for water with proper account of its vibrations, liberations and also hydrogen bonding. It is also of interest to study the temperature effect and the concentration dependence of the conductivity. The time-dependent friction can also be calculated from the present formalism and be used for the study of isotope effect in proton transfer reactions or other aspects of chemical dynamics

  11. Effect of gamma irradiation on viscosity of aqueous solutions of some natural polymers

    International Nuclear Information System (INIS)

    Nguyen Tan Man; Truong Thi Hanh; Le Quang Luan; Le Hai; Nguyen Quoc Hien

    2000-01-01

    Effect of gamma irradiation on viscosity of aqueous solution of alginate and carbon xylmethyl cellulose (CMC) irradiated in solid state has been carried out. the viscosity of aqueous solution of alginate and CMC decreased remarkably with increasing dose and the viscosity of 2% solution of above polymers irradiated at 50 kGy was about 100 times lower than the original one. (author)

  12. Behaviors of nitrato complexes of nitrosylruthenium in aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Sugimoto, S [Radia Industry Co. Ltd., Takasaki (Japan)

    1979-11-01

    Nitrato nitrosylruthenium complexes (RuNO(NO/sub 3/)sub(x)(H/sub 2/O)sub(5-x))sup((3-x)+) readily dissociate in aqueous solutions with decrease in pH and increase in electrical conductivity of the solutions. This study aimed to elucidate the behaviours of dissociation of the complexes with time. The change in the amount of undissociated complexes was determined with time. The results indicated that the dissociation was a multi-order reaction involving both protolysis and hydrolysis. The protolysis completed in relatively short period within (several tens of minutes), but it depended on the concentration of the complexes in the solution. The completion of the protolysis and the formation of the resulting dissociation products were observed by absorption spectrometry. The dissociation products, which were assumed as aquohydroxy complexes, underwent the successive step-wise dissociation for a prolonged period as revealed by pH measurements. The rate constants involved in the step-wise dissociation, process were obtained. The degree of dissociation and dissociation constant of the complexes were measured by conductometry.

  13. Behaviors of nitrato complexes of nitrosylruthenium in aqueous solutions

    International Nuclear Information System (INIS)

    Sugimoto, Senichi

    1979-01-01

    Nitrato nitrosylruthenium complexes [RuNO(NO 3 )sub(x)(H 2 O)sub(5-x)]sup((3-x)+) readily dissociate in aqueous solutions with decrease in pH and increase in electrical conductivity of the solutions. This study aimed to elucidate the behaviours of dissociation of the complexes with time. The change in the amount of undissociated complexes was determined with time. The results indicated that the dissociation was a multi-order reaction involving both protolysis and hydrolysis. The protolysis completed in relatively short period within (several tens of minutes), but it depended on the concentration of the complexes in the solution. The completion of the protolysis and the formation of the resulting dissociation products were observed by absorption spectrometry. The dissociation products, which were assumed as aquohydroxy complexes, underwent the successive step-wise dissociation for a prolonged period as revealed by pH measurements. The rate constants involved in the step-wise dissociation, process were obtained. The degree of dissociation and dissociation constant of the complexes were measured by conductometry. (author)

  14. Radiation-induced reduction of ditetrazolium salt in aqueous solutions

    International Nuclear Information System (INIS)

    Sadeghi, Ali; Chaychian, Mahnaz; Al-Sheikhly, Mohamad; McLaughlin, W.L.

    2002-01-01

    Color formation in aqueous solutions of the ditetrazolium salt blue tetrazolium (BT 2+ ) in the absence or presence of oxygen is a complex radiation chemical reaction. The final stable product is the poorly soluble diformazan violet to blue pigment having a broad spectral absorption band (λ max =552 nm). The reaction of BT 2+ with the hydrated electron proceeds by rapid reduction of BT 2+ followed by protonation at the nitrogen closest to the unsubstituted phenyl group, via the two intermediate tetrazolinyl radicals shared by the ditetrazole ring nitrogens. The effect of solution pH, N 2 O saturation, and the presence of the reducing agent dextrose are examined. The system serves as a radiochromic sensor and a dosimeter of ionizing radiations. Solutions of 5 mmol l -1 BT 2+ at pH 7.3 serve as dosimeters over an absorbed-dose range of approximately 0.2-6 kGy (dearated, with a range of 1-8 mmol l -1 dextrose) and of about 1-15 kGy (aerated, with 0.1 mol l -1 sodium formate and 5 mmol l -1 dextrose)

  15. Gamma-radiolysis of some glycoproteins in dilute aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Nagrani, S

    1981-01-01

    A study has been made of the radiation-induced damage of some glycoproteins in dilute aqueous solutions. By use of specific radical scavengers, the roles of the individual free radicals, formed by ..gamma..-radiolysis, in causing damage has been assessed. The most effective radical in causing damage to human and porcine glycopolypeptide is the OH radical. The structure of the different blood group glycopolypeptides determines the sensitivity towards the free radical attack. The glycopolypeptide shows depolymerization and a characteristic absorption at approximately 270 nm due to the formation of additional products on irradiation. Chemical changes of the irradiated glycopolypeptide solutions revealed significant damage to the oligosaccharide chain and the polypeptide core of the glycopolypeptide. The radiation-induced inactivation of another glycoprotein, external yeast invertase, due to different radical species at pH 7.0 decreases in the following order: ea-barq > OH radical > (SCN) radical/sub 2//sup -/ > Br radical/sub 2//sup -/. The structure of this enzyme, accounts for the mechanism of enzyme inactivation and the relative damage of carbohydrate and amino acid residues. The irradiated enzyme solutions show significant changes in their electrophoretic behaviour on cellogel electrophoresis due to the formation of radiolysis products, which also show characteristic absorption maxima at approximately 275 nm. (author).

  16. Neutron dosimetry using aqueous solutions of lithium acetate

    International Nuclear Information System (INIS)

    Rakovan, L.J.

    1996-01-01

    A thermal neutron dosimetry system using the 6 Li(n,α) 3 H reaction and liquid scintillation counting of tritium was developed. Lithium acetate was chosen to supply the 6 Li in the aqueous dosimetry solutions. Neutron irradiations were completed using The Ohio State University Research Reactor. After two sets of samples were irradiated, variables in the system such as the mass of lithium acetate in the solutions and the counting window of the liquid scintillation counter used to analyze the sample were chosen. The system was evaluated by completing two sets of 23 minute irradiations with the reactor at 500 kW, 50 kW, 5 kW, and one irradiation at 500 W. The samples irradiated at 500 W were below the threshold of the system, and could not be used. Prompt analysis was essential due to loss of detectable emissions in the dosimetry solutions over time. The thermal neutron fluences calculated with the data from the samples were compared to the fluences determined from gold wire irradiations. The fluence values differed at most by 6%. The fluence values calculated from the samples were consistently less than those determined from the gold wires

  17. Molecular dynamics simulation studies of caffeine aggregation in aqueous solution.

    Science.gov (United States)

    Tavagnacco, Letizia; Schnupf, Udo; Mason, Philip E; Saboungi, Marie-Louise; Cesàro, Attilio; Brady, John W

    2011-09-22

    Molecular dynamics simulations were carried out on a system of eight independent caffeine molecules in a periodic box of water at 300 K, representing a solution near the solubility limit for caffeine at room temperature, using a newly developed CHARMM-type force field for caffeine in water. Simulations were also conducted for single caffeine molecules in water using two different water models (TIP3P and TIP4P). Water was found to structure in a complex fashion around the planar caffeine molecules, which was not sensitive to the water model used. As expected, extensive aggregation of the caffeine molecules was observed, with the molecules stacking their flat faces against one another like coins, with their methylene groups staggered to avoid steric clashes. A dynamic equilibrum was observed between large n-mers, including stacks with all eight solute molecules, and smaller clusters, with the calculated osmotic coefficient being in acceptable agreement with the experimental value. The insensitivity of the results to water model and the congruence with experimental thermodynamic data suggest that the observed stacking interactions are a realistic representation of the actual association mechanism in aqueous caffeine solutions.

  18. Hydrophobicity and thermodynamic response for aqueous solutions of amphiphiles

    Science.gov (United States)

    Zemánková, Katerina; Troncoso, Jacobo; Cerdeiriña, Claudio A.; Romaní, Luis; Anisimov, Mikhail A.

    2016-06-01

    The anomalous behavior of aqueous solutions of amphiphiles in the water-rich region is analyzed via a phenomenological approach that utilizes the isobaric heat capacity Cp as an experimental probe. We report extensive data for solutions of 14 amphiphiles as a function of temperature at atmospheric pressure. Beyond that, Cp data but also isobaric thermal expansivities and isothermal compressibilities for three solutions of tert-butanol as a function of both temperature and pressure are presented. Results rule out the possibility that the observed phenomenology is associated with the anomalous thermodynamics of pure water. Indeed, our Cp data, quantitatively consistent with recent spectroscopic analyses, suggest that water-mediated interactions between the nonpolar parts of amphiphiles are at the origin of anomalies, with the effects of such "hydrophobic aggregation" being observed at mole fractions as small as 0.01. Physicochemical details like the size, the electronic charge distribution and the geometry of amphiphile molecules as well as third-order derivatives of the Gibbs energy and the associated Koga lines support the above claims while they further contribute to characterizing the role of hydrophobicity in these phenomena. Progress with a view to gain a deeper, more concrete understanding remains.

  19. Aqueous solution of basic fuchsin as food irradiation dosimeter

    International Nuclear Information System (INIS)

    Khan, H.M.; Naz, S.

    2007-01-01

    Dosimetric characterization of aqueous solution of basic fuchsin was studied spectrophotometrically for possible application in the low-dose food irradiation dosimetry. Absorption spectra of unirradiated and irradiated solutions were determined and the decrease in absorbance with the dose was noted down. Radiation-induced bleaching of the dye was measured at wavelengths of maximum absorption λ max (540nm) as well as 510nm and 460 nm. At all these wavelengths, the decrease in absorbance of the dosimeter was linear with respect to the absorbed dose from 50 Gy to 600 Gy. The stability of dosimetric solution during post-irradiation storage in the dark at room temperature showed that after initial bleaching during first ten to twenty days, the response was almost stable for about 34 days. The study on the effect of different light and temperature conditions also showed that the response gradually decreased during the storage period of 34 days, which shows that basic fuchsin dye is photosensitive as well as thermally sensitive. (authors)

  20. Interaction of gypsum with lead in aqueous solutions

    International Nuclear Information System (INIS)

    Astilleros, J.M.; Godelitsas, A.; Rodriguez-Blanco, J.D.; Fernandez-Diaz, L.; Prieto, M.; Lagoyannis, A.; Harissopulos, S.

    2010-01-01

    Sorption processes on mineral surfaces are a critical factor in controlling the distribution and accumulation of potentially harmful metals in the environment. This work investigates the effectiveness of gypsum (CaSO 4 .2H 2 O) to sequester Pb. The interaction of gypsum fragments with Pb-bearing solutions (10, 100 and 1000 mg/L) was monitored by performing macroscopic batch-type experiments conducted at room temperature. The aqueous phase composition was periodically determined by Atomic Absorption Spectrometry (AAS), Ion Chromatography (IC) and Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES). Regardless of the [Pb aq ] initial , a [Pb aq ] final aq ] initial ≥ 100 mg/L and significantly slower (t > 1 week) for [Pb aq ] initial = 10 mg/L. Speciation calculations revealed that after a long time of interaction (1 month), all the solutions reached equilibrium with respect to both gypsum and anglesite. For [Pb aq ] initial ≥ 100 mg/L, sorption takes place mainly via the rapid dissolution of gypsum and the simultaneous formation of anglesite both on the gypsum surface and in the bulk solution. In the case of [Pb aq ] initial = 10 mg/L, no anglesite precipitation was observed, but surface spectroscopy (proton Rutherford Backscattering Spectroscopy, p-RBS) confirmed the formation of Pb-bearing surface layers on the (0 1 0) gypsum surface in this case also. This study shows that the surface of gypsum can play an important role in the attenuation of Pb in contaminated waters.

  1. Supercharging Protein Complexes from Aqueous Solution Disrupts their Native Conformations

    Science.gov (United States)

    Sterling, Harry J.; Kintzer, Alexander F.; Feld, Geoffrey K.; Cassou, Catherine A.; Krantz, Bryan A.; Williams, Evan R.

    2012-02-01

    The effects of aqueous solution supercharging on the solution- and gas-phase structures of two protein complexes were investigated using traveling-wave ion mobility-mass spectrometry (TWIMS-MS). Low initial concentrations of m-nitrobenzyl alcohol ( m-NBA) in the electrospray ionization (ESI) solution can effectively increase the charge of concanavalin A dimers and tetramers, but at higher m-NBA concentrations, the increases in charge are accompanied by solution-phase dissociation of the dimers and up to a ~22% increase in the collision cross section (CCS) of the tetramers. With just 0.8% m-NBA added to the ESI solution of a ~630 kDa anthrax toxin octamer complex, the average charge is increased by only ~4% compared with the "native" complex, but it is sufficiently destabilized so that extensive gas-phase fragmentation occurs in the relatively high pressure regions of the TWIMS device. Anthrax toxin complexes exist in either a prechannel or a transmembrane channel state. With m-NBA, the prechannel state of the complex has the same CCS/charge ratio in the gas phase as the transmembrane channel state of the same complex formed without m-NBA, yet undergoes extensive dissociation, indicating that destabilization from supercharging occurs in the ESI droplet prior to ion formation and is not a result of Coulombic destabilization in the gas phase as a result of higher charging. These results demonstrate that the supercharging of large protein complexes is the result of conformational changes induced by the reagents in the ESI droplets, where enrichment of the supercharging reagent during droplet evaporation occurs.

  2. Spontaneous vesicle phase formation by pseudogemini surfactants in aqueous solutions.

    Science.gov (United States)

    Sun, Nan; Shi, Lijuan; Lu, Fei; Xie, Shuting; Zheng, Liqiang

    2014-08-14

    The phase behavior of a kind of pseudogemini surfactant in aqueous solutions, formed by the mixture of sodium dodecyl benzene sulfonate (SDBS) and butane-1,4-bis (methylimidazolium bromide) ([mim-C4-mim]Br2) or butane-1,4-bis(methylpyrrolidinium bromide) ([mpy-C4-mpy]Br2) in a molar ratio of 2 : 1, is reported in the present work. When [mim-C4-mim]Br2 or [mpy-C4-mpy]Br2 is mixed with SDBS in aqueous solutions, one cationic [mim-C4-mim]Br2 or [mpy-C4-mpy]Br2 molecule "bridges" two SDBS molecules by noncovalent interactions (e.g. electrostatic, π-π stacking, and σ-π interactions), behaving like a pseudogemini surfactant. Vesicles can be formed by this kind of pseudogemini surfactant, determined by freeze-fracture transmission electron microscopy (FF-TEM) or cryogenic-transmission electron microscopy (cryo-TEM) and dynamic light scattering (DLS). The mixed system of sodium dodecyl sulfate (SDS) with [mim-C4-mim]Br2 or [mpy-C4-mpy]Br2 was also constructed, and only micelles were observed. We infer that a pseudogemini surfactant is formed under the synergic effect of electrostatic, π-π stacking, and σ-π interactions in the SDBS/[mim-C4-mim]Br2/H2O system, while electrostatic attraction and hydrophobic interactions may provide the directional force for vesicle formation in the SDBS/[mpy-C4-mpy]Br2/H2O system.

  3. Thermodynamics of dilute aqueous solutions of imidazolium based ionic liquids

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Tejwant [Salt and Marine Chemicals Division, Central Salt and Marine Chemicals Research Institute, Council of Scientific and Industrial Research (CSIR), G.B. Marg, Bhavnagar 364002 (India); Kumar, Arvind, E-mail: arvind@csmcri.or [Salt and Marine Chemicals Division, Central Salt and Marine Chemicals Research Institute, Council of Scientific and Industrial Research (CSIR), G.B. Marg, Bhavnagar 364002 (India)

    2011-06-15

    Research highlights: The thermodynamic behaviour of aqueous imidazolium ILs has been investigated. Volumetric and ultrasonic results indicated the hydrophobic hydration of ILs. Viscometric studies revealed studied ionic liquids as water-structure makers. Hydration number increased with increase in alkyl chain length of the cation. - Abstract: Experimental measurements of density {rho}, speed of sound u, and viscosity {eta} of aqueous solutions of various 1-alkyl-3-methylimidazolium based ionic liquid (IL) solutions have been performed in dilute concentration regime at 298.15 K to get insight into hydration behaviour of ILs. The investigated ILs are based on 1-alkyl-3-methylimidazolium cation, [C{sub n}mim] having [BF{sub 4}]{sup -}, [Cl]{sup -}, [C{sub 1}OSO{sub 3}]{sup -}, and [C{sub 8}OSO{sub 3}]{sup -} as anions where n = 4 or 8. Several thermodynamic parameters like apparent molar volume {phi}{sub V}, isentropic compressibility {beta}{sub s}, and viscosity B-coefficients have been derived from experimental data. Limiting value of apparent molar volume has been discussed in terms of intrinsic molar volume (V{sub int}) molar electrostriction volume (V{sub elec}), molar disordered (V{sub dis}), and cage volume (V{sub cage}). Viscosity B-coefficients have been used to quantify the kosmotropic or chaotropic nature of ILs. Hydration number of ILs obtained using elctrostriction volume, isentropic compressibility, viscosity, and differential scanning calorimetry have been found to be comparative within the experimental error. The hydrophobic hydration has found to play an important role in hydration of ILs as compared to hydration due to hydrogen bonding and electrostriction. Limiting molar properties, hydration numbers, and B-coefficients have been discussed in terms of alkyl chain length of cation or nature of anion.

  4. Thermodynamics of dilute aqueous solutions of imidazolium based ionic liquids

    International Nuclear Information System (INIS)

    Singh, Tejwant; Kumar, Arvind

    2011-01-01

    Research highlights: → The thermodynamic behaviour of aqueous imidazolium ILs has been investigated. → Volumetric and ultrasonic results indicated the hydrophobic hydration of ILs. → Viscometric studies revealed studied ionic liquids as water-structure makers. → Hydration number increased with increase in alkyl chain length of the cation. - Abstract: Experimental measurements of density ρ, speed of sound u, and viscosity η of aqueous solutions of various 1-alkyl-3-methylimidazolium based ionic liquid (IL) solutions have been performed in dilute concentration regime at 298.15 K to get insight into hydration behaviour of ILs. The investigated ILs are based on 1-alkyl-3-methylimidazolium cation, [C n mim] having [BF 4 ] - , [Cl] - , [C 1 OSO 3 ] - , and [C 8 OSO 3 ] - as anions where n = 4 or 8. Several thermodynamic parameters like apparent molar volume φ V , isentropic compressibility β s , and viscosity B-coefficients have been derived from experimental data. Limiting value of apparent molar volume has been discussed in terms of intrinsic molar volume (V int ) molar electrostriction volume (V elec ), molar disordered (V dis ), and cage volume (V cage ). Viscosity B-coefficients have been used to quantify the kosmotropic or chaotropic nature of ILs. Hydration number of ILs obtained using elctrostriction volume, isentropic compressibility, viscosity, and differential scanning calorimetry have been found to be comparative within the experimental error. The hydrophobic hydration has found to play an important role in hydration of ILs as compared to hydration due to hydrogen bonding and electrostriction. Limiting molar properties, hydration numbers, and B-coefficients have been discussed in terms of alkyl chain length of cation or nature of anion.

  5. Humic acid removal from aqueous solutions by peroxielectrocoagulation process

    Directory of Open Access Journals (Sweden)

    Ahmad Reza Yazdanbakhsh

    2015-06-01

    Full Text Available Background: Natural organic matter is the cause of many problems associated with water treatment such as the presence of disinfection by-products (DBPs and membrane fouling during water filtration. In this study, the performance of the peroxi-electrocoagulation process (PEP was investigated for the removal of humic acids (HAs from aqueous solutions. Methods: PEP was carried out for the removal of HA using a plexiglas reactor with a volume of 2 L and fitted with iron electrodes and a direct current supply (DC. Samples were taken at various amounts of pH (2-4, current density (1 and 2A/cm2, hydrogen peroxide (50-150 mg/L and reaction time (5-20 minutes and then filtered to remove sludge formed during reaction. Finally, the HA concentration was measured by UV absorbance at 254 nm (UV254. Results: Results indicated that increasing the concentration of H2O2 from 50 to 150 mg/L increased HA removal efficiency from 83% to 94.5%. The highest removal efficiency was observed at pH 3.0; by increasing the pH to the alkaline range, the efficiency of the process was reduced. It was found that HA removal efficiency was high in current density 1A/cm2. Increasing current density up to 1 A cm-2 caused a decrease in removal efficiency. Results of this study showed that under the optimum operating range for the process ([current density] = 1A/cm2, [hydrogen peroxide concentration] = 150 mg/L, [reaction time]= 20 minutes and [pH]= 3.0, HA removal efficiency reached 98%. Conclusion: It can be concluded that PEP has the potential to be utilized for cost-effective removal of HA from aqueous solutions.

  6. Process for the recovery of alkali metal salts from aqueous solutions thereof

    International Nuclear Information System (INIS)

    Vitner, J.

    1984-01-01

    In an integrated process for the recovery of alkakli metal phenates and carboxylates from aqueous solutions thereof, the aqueous solution is spray dried and the drying gas stream is contacted with an aqueous alkali metal salt solution which dissolves the particles of the alkali metal salt that were entrained in the drying gas stream. The salt-free inert gas stream is then dried, heated, and returned to the spray dryer

  7. Orientational order and dynamics of water in bulk and in aqueous solutions of uranyl ions

    International Nuclear Information System (INIS)

    Chopra, Manish; Choudhury, Niharendu

    2014-01-01

    Molecular dynamics simulations in canonical ensemble of aqueous solutions of uranyl nitrate and bulk water at ambient condition have been carried out to investigate orientational order and dynamics of water. The orientational distributions of water around a central water molecule in bulk water and around a uranyl ion in an aqueous uranyl solution have been calculated. Orientational dynamics of water in bulk and in aqueous uranyl nitrate solution have also been analysed. (author)

  8. Influence aqueous solutions on the mechanical behavior of argillaceous rocks

    International Nuclear Information System (INIS)

    Wakim, J.

    2005-12-01

    The hydration of the shale with an aqueous solution induces a swelling deformation which plays an important role in the behaviour of the structures excavated in this type of grounds. This deformation is marked by a three-dimensional and anisotropic character and involves several mechanisms like adsorption, osmosis or capillarity. Several researches were dedicated to swelling and were often much debated due to the complexity of the implied phenomena. The goal of this thesis is therefore to contribute to a better understanding of shale swelling when the rock is confined and hydrated with an aqueous solution. The main part of the work accomplished was related to the Lorraine shale and to the Tournemire shale. To characterize swelling and to identify the main governing parameters, it was necessary to start the issue with an experimental approach. Many apparatus were then developed to carry out tests under various conditions of swelling. In order to facilitate the interpretation of the tests and thereafter the modelling of the behaviour, the experimental procedure adopted consisted of studying first the mechanical aspect and then the chemical aspect of swelling. In the mechanical part, swelling was studied by imposing on the sample a mechanical loading while maintaining during the tests the same aqueous solution. The principal parameters which were studied are the effect of the lateral conditions on axial swelling (impeded strain or constant stress) as well as the influence of the axial stress on radial swelling. The anisotropy of swelling was studied by carrying out, for different orientations of the sample, tests of free swelling, impeded swelling and uniaxial swelling. These various mechanical tests allowed to study the three-dimensional anisotropic swelling in all the conditions and to select the most appropriate test to be used in the second phase of the research. The precise analysis performed to explain the mechanisms behind the swelling of an argillaceous rock

  9. Measurement of bulk etch rates for poly-allyl-diglycol carbonate (PADC) and cellulose nitrate in a broad range of concentration and temperature of NaOH etching solution

    International Nuclear Information System (INIS)

    Hermsdorf, D.; Hunger, M.; Starke, S.; Weickert, F.

    2007-01-01

    In the present work the dependence of the bulk etch rate v B for solid state nuclear track detectors (SSNTD) on the concentration c and the temperature T of the NaOH etching solution has been studied for material types PADC and cellulose nitrate. As commonly applied exponents of PADC and cellulose nitrate material, the commercial products CR-39 and LR-115 were investigated. The concentration and temperature have been varied in the ranges 0.5moll -1 -1 and 313 -1 and T between 313 and 333K for cellulose nitrate, respectively. The application of a simple Arrhenius-law of chemical reactions fails in the interpretation of the dependence on the concentration. A constant activation energy cannot describe the behaviour of v B (c,T) over the whole range of concentration. To understand the deviation, more qualified models treating the superposition of chemical and physical processes including reaction kinetics and material transport phenomena by diffusion have to be developed and tested

  10. Removal of phenol from aqueous solution using polymer inclusion membrane based on mixture of CTA and CA

    Science.gov (United States)

    Benosmane, Nadjib; Boutemeur, Baya; Hamdi, Safouane M.; Hamdi, Maamar

    2018-03-01

    Nowadays, there are increasingly stringent regulations requiring more and more treatment of industrial effluents to generate product waters which could be easily reused or disposed of to the environment without any harmful effects. In the present work, the removal of phenol from aqueous solution across polymer inclusion membrane (PIM), based on mixture of cellulose triacetate and cellulose acetate as support (75/25%), calix[4]resorcinarene derivative as a carrier and 2-nitrophenyl octyl ether (2-NPOE) as plasticizer was investigated. The experimental part of this investigation involved the influence of carrier nature, plasticizer concentration, pH phases, and phenol initial concentration on the removal efficiency of phenol from synthetic wastewater. A PIM containing 0.1 g (of mixture polymer), (0.15 g/g mixture of polymer) of carrier and (0.03 ml/g mixture of polymer) of 2-NPOE provided the highest percentage of phenol removal efficiency over a 6-day transport; the removal was found to be about 95%, indeed the removal was found to be highly dependent of pH phases. The feed solution in these transport experiments was at pH 2, while the stripping solution contained 0.20 M NaOH. This study claims that the PIM with a mixture of cellulose derivatives can be used effectively to remove phenols from wastewaters.

  11. Determination of Optimal Temperature for Biosorption of Heavy Metal Mixture from Aqueous Solution by Pretreated Biomass of Aspergillus niger

    Directory of Open Access Journals (Sweden)

    Javad Yousefi

    2012-01-01

    Full Text Available Biosorption is a novel technology that uses dead and inactive biomass for removal of heavy metals from aqueous solution. Some parameters such as temperature, contact time, solution pH, initial metal concentration, biosorbent dose and also agitating speed of solution and biosorbent mixing can affect the amount of metal sorption by biosorbent. The aim of this study was to investigate the effects of different treatments of temperatures (25, 35, 45 and 55oC on biosorption of metals mixture in order to determine optimal temperature for more metals removal from aqueous solution. This study uses dead and pretreated biomass of Aspergillus niger with 0.5N NaOH for removal of Zn(II, Co(II and Cd(II. In all temperature treatments and in the case of all of heavy metals, maximum amount of metal sorption and concentration decrease was occurred in first 5 minutes and achieved to equilibrium after 20 minute. The percent of metals sorption show growth trend with temperature increase. Between 4 experimental treatments, 55oC treatment was shown maximum sorption and 25oC was shown minimum sorption amount. The percent of Cr(II sorption was increase from 28.5% in 25oC to 44.7% in 55oC. Also, this increase was from 40% to 58% for Cd(II and from 37.7% to 65.6% for Zn(II. About 60% of increase in sorption by A. niger was due to increase in temperature. Therefore the amount of metals sorption can be increase, only with temperature increase and without any biomass addition.

  12. Removal of Ni(II), Zn(II) and Pb(II) ions from single metal aqueous solution using rice husk-based activated carbon

    Energy Technology Data Exchange (ETDEWEB)

    Taha, Mohd F., E-mail: faisalt@petronas.com.my; Shaharun, Maizatul S. [Fundamental and Applied Sciences Department, Universiti Teknologi PETRONAS, Bandar Seri Iskandar, 31750, Perak Darul Ridzuan (Malaysia); Shuib, Anis Suhaila, E-mail: anisuha@petronas.com.my; Borhan, Azry [Chemical Engineering Department, Universiti Teknologi PETRONAS, Bandar Seri Iskandar, 31750, Perak Darul Ridzuan (Malaysia)

    2014-10-24

    An attempt was made to investigate the potential of rice husk-based activated carbon as an alternative low-cost adsorbent for the removal of Ni(II), Zn(II) and Pb(II) ions from single aqueous solution. Rice husk-based activated carbon was prepared via treatment of rice husk with NaOH followed by the carbonization process at 400°C for 2 hours. Three samples, i.e. raw rice husk, rice husk treated with NaOH and rice husk-based activated carbon, were analyzed for their morphological characteristics using field-emission scanning electron microscope/energy dispersive X-ray (FESEM/EDX). These samples were also analyzed for their carbon, hydrogen, nitrogen, oxygen and silica contents using CHN elemental analyzer and FESEM/EDX. The porous properties of rice husk-based activated carbon were determined by Brunauer-Emmett-Teller (BET) surface area analyzer, and its surface area and pore volume were 255 m{sup 2}/g and 0.17 cm{sup 2}/g, respectively. The adsorption studies for the removal of Ni(II), Zn(II) and Pb(II) ions from single metal aqueous solution were carried out at a fixed initial concentration of metal ion (150 ppm) with variation amount of adsorbent (rice husk-based activated carbon) as a function of varied contact time at room temperature. The concentration of each metal ion was analyzed using atomic absorption spectrophotometer (AAS). The results obtained from adsorption studies indicate the potential of rice husk as an economically promising precursor for the preparation of activated carbon for removal of Ni(II), Zn(II) and Pb(II) ions from single aqueous solution. Isotherm and kinetic model analyses suggested that the experimental data of adsorption studies fitted well with Langmuir, Freundlich and second-order kinetic models.

  13. Adsorption of cesium on cement mortar from aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Volchek, Konstantin, E-mail: konstantin.volchek@ec.gc.ca [Emergencies Science and Technology Section, Environment Canada, 335 River Road, Ottawa, Ontario, Canada K1A 0H3 (Canada); Miah, Muhammed Yusuf [Emergencies Science and Technology Section, Environment Canada, 335 River Road, Ottawa, Ontario, Canada K1A 0H3 (Canada); Department of Applied Chemistry and Chemical Technology, Noakhali Science and Technology University (Bangladesh); Kuang, Wenxing; DeMaleki, Zack [Emergencies Science and Technology Section, Environment Canada, 335 River Road, Ottawa, Ontario, Canada K1A 0H3 (Canada); Tezel, F. Handan [Department of Chemical and Biological Engineering, University of Ottawa, 161 Louis-Pasteur, Ottawa, Ontario, Canada K1N 6N5 (Canada)

    2011-10-30

    Highlights: {yields} The adsorption of cesium on cement mortar was investigated in a range of temperatures and cesium concentrations. {yields} The pseudo-second order kinetic model produced a good fit with the experimental kinetic data. {yields} Equilibrium test results correlated well with the Freundlich isotherm adsorption model. {yields} The interaction between cesium ions and cement mortar was dominated by chemical adsorption. - Abstract: The adsorption of cesium on cement mortar from aqueous solutions was studied in series of bench-scale tests. The effects of cesium concentration, temperature and contact time on process kinetics and equilibrium were evaluated. Experiments were carried out in a range of initial cesium concentrations from 0.0103 to 10.88 mg L{sup -1} and temperatures from 278 to 313 K using coupons of cement mortar immersed in the solutions. Non-radioactive cesium chloride was used as a surrogate of the radioactive {sup 137}Cs. Solution samples were taken after set periods of time and analyzed by inductively coupled plasma mass spectroscopy. Depending on the initial cesium concentration, its equilibrium concentration in solution ranged from 0.0069 to 8.837 mg L{sup -1} while the respective surface concentration on coupons varied from 0.0395 to 22.34 {mu}g cm{sup -2}. Equilibrium test results correlated well with the Freundlich isotherm model for the entire test duration. Test results revealed that an increase in temperature resulted in an increase in adsorption rate and a decrease in equilibrium cesium surface concentration. Among several kinetic models considered, the pseudo-second order reaction model was found to be the best to describe the kinetic test results in the studied range of concentrations. The adsorption activation energy determined from Arrhenius equation was found to be approximately 55.9 kJ mol{sup -1} suggesting that chemisorption was the prevalent mechanism of interaction between cesium ions and cement mortar.

  14. Radiation degradation of Congo Red in aqueous solution

    International Nuclear Information System (INIS)

    Ma Hongjuan; Wang Min; Yang Ruiyuan; Wang Wenfeng; Shen Zhongqun; Yao Side

    2006-01-01

    About one-half of the dyes used in textile industry are azo dyes, and as a consequence a lot of azo dyes are released into the environment with industrial wastewater. Because of complex structures of the dyes, biological, physical and chemical treatments of dye effluents are inefficient. In this study, radiation degradation of Congo Red in aqueous solutions was investigated in different reaction systems. Both pulsed radiolysis and laser flash photolysis experiments were carried out for better understandings of degradation mechanisms involved in the treatments. Congo Red solutions saturated by air, N 2 O, O 2 , N 2 O or N 2 and added with tert-butanol were irradiated to 0-14.8 kGy. The absorption spectra, degradation efficiency, TOC (total organic carbon) removal and pH changes of the solutions were investigated. The main radiolytic products from Congo Red samples irradiated in steady-state were determined by HPLC-MS. And probable reaction mechanisms were proposed. Effects of primary species from water radiolysis, such as e aq - , . OH and . O 2 . /HO 2 . on the degradation behavior of the dye were discussed. Below 5 kGy in γ-rays irradiation, the bleaching efficiency of Congo Red was (N 2 +tert-butanol) >O 2 >air>N 2 O>N 2 . Complete degradation of Congo Red was observed at 4.0, 5.5 and 10.2 kGy irradiation of the aqueous solutions saturated by N 2 with tert-butanol added, O 2 and N 2 O, respectively. With just oxidative or reductive species, highly conjugated part of Congo Red molecules could be destroyed. While oxidative species produced from water radiolysis could oxidize the Congo Red more effectively, making the dye to break into fatty acids and CO 2 finally. In the solution saturated with N 2 and air, the primary active species were both of oxidative and reductive and the highly conjugated part of Congo Red molecules could not be destroyed completely up to 14.8 kGy of γ-ray irradiation. It was more difficult to achieve high TOC removal in comparison with

  15. The effect of gamma irradiation on rice protein aqueous solution

    Science.gov (United States)

    Baccaro, Stefania; Bal, Oya; Cemmi, Alessia; Di Sarcina, Ilaria

    2018-05-01

    The use of proteins as natural biopolymers are sensibly increasing in several application fields such as food industry, packaging and environment protection. In particular, rice proteins (RP) present good nutritional, hypoallergenic and healthful properties very interesting for human consumption. Since ionizing radiation can be successfully applied on protein containing systems involved in different industrial processes, this work aims to determine the effect of gamma radiation on 5 wt%-7.5 wt% RP aqueous solutions in a wide range of absorbed doses up to around 40 kGy. The changes of RP secondary and tertiary structures and their chemical composition were followed by UV-VIS absorbance spectroscopy, luminescence analysis and pH measurements. The experimental data showed the occurrence of the unfolding of RP chains with the increase of the absorbed dose and the formation of new molecules, due to the reaction among tryptophane and tyrosine amino acids and the radical species induced by gamma radiation. The results are also confirmed by the modification of the pH values measured for the irradiated solutions.

  16. Photo-induced degradation of some flavins in aqueous solution

    International Nuclear Information System (INIS)

    Holzer, W.; Shirdel, J.; Zirak, P.; Penzkofer, A.; Hegemann, P.; Deutzmann, R.; Hochmuth, E.

    2005-01-01

    The blue-light induced photo-degradation of FMN, FAD, riboflavin, lumiflavin, and lumichrome in aqueous solution at pH 8 is studied by measurement of absorption coefficient spectral changes due to continuous excitation at 428 nm. The quantum yields of photo-degradation determined are φ D (riboflavin, pH 8) ∼ 7.8 x 10 -3 , φ D (FMN, pH 5.6) ∼ 7.3 x 10 -3 , φ D (FMN, pH 8) ∼ 4.6 x 10 -3 , φ D (FAD, pH 8) ∼ 3.7 x 10 -4 , φ D (lumichrome, pH 8) ∼ 1.8 x 10 -4 , and φ D (lumiflavin, pH 8) approx. 1.1 x 10 -5 . In a mass-spectroscopic analysis, the photo-products of FMN dissolved in water (solution pH is 5.6) were identified to be lumichrome and the lumiflavin derivatives dihydroxymethyllumiflavin, formyllumiflavin, and lumiflavin-hydroxy-acetaldehyde. An absorption and emission spectroscopic characterisation of the primary photoproducts of FMN at pH 8 is carried out

  17. Degradation of diuron in aqueous solution by dielectric barrier discharge

    Energy Technology Data Exchange (ETDEWEB)

    Feng Jingwei [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment Nanjing University, Nanjing 210093 (China); Zheng Zheng [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment Nanjing University, Nanjing 210093 (China)], E-mail: zzheng@nju.edu.cn; Sun Yabing; Luan Jingfei; Wang Zhen; Wang Lianhong; Feng Jianfang [State Key Laboratory of Pollution Control and Resource Reuse, School of the Environment Nanjing University, Nanjing 210093 (China)

    2008-06-15

    Degradation of diuron in aqueous solution was conducted in a dielectric barrier discharge (DBD) reactor and the proposed degradation mechanism was investigated in detail. The factors that affect the degradation of diuron were examined. The degradation efficiency of diuron and the removal of total organic carbon (TOC) increased with increasing input power, and the degradation of diuron by DBD fitted first-order kinetics. Both strong acidic and alkaline solution conditions could improve diuron degradation efficiency and TOC removal rate. Degradation of diuron could be accelerated or inhibited in the presence of H{sub 2}O{sub 2} depending on the dosage. The degradation efficiency increased dramatically with adding Fe{sup 2+}. The removal of TOC and the amount of the detected Cl{sup -}, NO{sub 3}{sup -} and NH{sub 4}{sup +} were increased in the presence of Fe{sup 2+}. The concentrations of oxalic and acetic acids were almost the same in the absence and presence of Fe{sup 2+}, but high concentration of formic acid was accumulated in the presence of Fe{sup 2+}. The main degradation pathway of diuron by DBD involved a series of dechlorination-hydroxylation, dealkylation and oxidative opening of the aromatic ring processes.

  18. Metal ion removal from aqueous solution using physic seed hull.

    Science.gov (United States)

    Mohammad, Masita; Maitra, Saikat; Ahmad, Naveed; Bustam, Azmi; Sen, T K; Dutta, Binay K

    2010-07-15

    The potential of physic seed hull (PSH), Jantropha curcas L. as an adsorbent for the removal of Cd(2+) and Zn(2+) metal ions from aqueous solution has been investigated. It has been found that the amount of adsorption for both Cd(2+) and Zn(2+) increased with the increase in initial metal ions concentration, contact time, temperature, adsorbent dosage and the solution pH (in acidic range), but decreased with the increase in the particle size of the adsorbent. The adsorption process for both metal ions on PSH consists of three stages-a rapid initial adsorption followed by a period of slower uptake of metal ions and virtually no uptake at the final stage. The kinetics of metal ions adsorption on PSH followed a pseudo-second-order model. The adsorption equilibrium data were fitted in the three adsorption isotherms-Freundlich, Langmuir and Dubinin-Radushkevich isotherms. The data best fit in the Langmuir isotherm indication monolayer chemisorption of the metal ions. The adsorption capacity of PSH for both Zn(2+) and Cd(2+) was found to be comparable with other available adsorbents. About 36-47% of the adsorbed metal could be leached out of the loaded PSH using 0.1M HCl as the eluting medium. 2010 Elsevier B.V. All rights reserved.

  19. Processes for working-up an aqueous fluosilicic acid solution

    Directory of Open Access Journals (Sweden)

    Alpha O. Toure

    2012-11-01

    Full Text Available Aqueous fluosilicic acid solutions were once considered to be only adverse by-products of phosphoric acid production, which required treatment to prevent ecosystem destruction when discharged into the sea. However, a range of chemicals can be generated by the transformation of this industrial waste product. Through experiments undertaken in the laboratory, we have shown the possibility of caustic soda production. Volumetric analysis showed caustic soda to be present as a 6%– 7%solution with yields of about 70% – 80%by weight. Two processes were investigated for the caustification of sodium fluoride, using different precipitates: sodium chloride and ethanol and are described by modelling caustification curves. The activation energies of precipitation determined by semi-empirical correlations showed that precipitation by ethanol (EA = 933.536 J/mol was more successful than precipitation by sodium chloride (EA = 7452.405 J/mol. Analyses performed on the precipitates highlighted compositions that are essential and useful constituents in the cement industry.

  20. Thermodynamics of aqueous solutions containing poly (N-isopropylacrylamide)

    Energy Technology Data Exchange (ETDEWEB)

    Poschlad, K. [Technical University of Berlin, Chair of Thermodynamics TK 7, Strasse des 17, Juni 135, 10623 Berlin (Germany); Enders, S., E-mail: sabine.enders@tu-berlin.d [Technical University of Berlin, Chair of Thermodynamics TK 7, Strasse des 17, Juni 135, 10623 Berlin (Germany)

    2011-03-15

    Hydrogels undergo reversible and discontinuous volume changes in response to variation of solution conditions such as solvent composition, temperature, salt concentration, and pH. In this contribution we focus our attention on the experimental and theoretical investigation of these swelling equilibria of aqueous cross-linked poly (N-isopropylacrylamide) solutions as well as on the connected demixing behavior of the linear polymer dissolved in water. For the experimental study of the (liquid + liquid) equilibrium an alternative method based on refractive index measurements is suggested. In order to calculate the swelling behavior a model combining an expression for the Gibbs free energy of mixing with an expression for the elastic network is applied. As a model for the Gibbs free energy of mixing the UNIQUAC-approach and the Koningsveld-Kleintjens model are used. For the elastic network contribution again two different theories, namely the phantom network theory and the affine network theory, were applied. Whereas the type of network theory has only a small influence on the calculation results, the Gibbs free energy of mixing has a large impact. Using the UNIQUAC-approach the swelling equilibria can be correlated close to the experimental data, however, this model predicts a homogeneous mixture for linear polymer chains in water. In contrast to this situation the Koningsveld-Kleintjens model does a good job in calculating the swelling equilibria as well as the demixing curve, however, the adjustable parameter must be changed slightly.

  1. Removal of Nitrate From Aqueous Solution Using Rice Chaff

    Directory of Open Access Journals (Sweden)

    Dehghani

    2015-09-01

    Full Text Available Background Nitrate is largely dissolved in the surface and ground water, due to its high solubility. Continual uptake of nitrite through drinking water can lead to problems and diseases (such as blue baby for humans, especially children. Objectives The aim of this study was to develop a new and inexpensive method for the removal of nitrate from water. In this regard, the possibility of using chaff for removal of nitrate from aqueous solutions was studied and the optimum operating conditions of nitrate removal was determined. Materials and Methods This is a cross-sectional study conducted in laboratory scale. The UV spectrophotometer at a wavelength of maximum absorbance (220 nm was used to determine the nitrate concentration. The effect of pH, amount of chaff, temperature, and contact time were investigated. Results The result of this study revealed that chaff as an absorbent could remove nitrate from solutions, and the efficiency of adsorption increased as contact time increased from 5 to 30 minutes, amount of chaff increased from 1 to 3 g, temperature increased in a range of 300 - 400°C and the amount of pH decreased from 10 to 3. The maximum adsorption rate was around pH 3 (53.14%. Conclusions It was shown that the removal efficiency of nitrate was directly proportional to the amount of chaff, temperature, and contact time but inversely to the pH. This study showed that nitrate removal by chaff is a promising technique.

  2. Photo-induced degradation of some flavins in aqueous solution

    Science.gov (United States)

    Holzer, W.; Shirdel, J.; Zirak, P.; Penzkofer, A.; Hegemann, P.; Deutzmann, R.; Hochmuth, E.

    2005-01-01

    The blue-light induced photo-degradation of FMN, FAD, riboflavin, lumiflavin, and lumichrome in aqueous solution at pH 8 is studied by measurement of absorption coefficient spectral changes due to continuous excitation at 428 nm. The quantum yields of photo-degradation determined are ϕD(riboflavin, pH 8) ≈ 7.8 × 10 -3, ϕD(FMN, pH 5.6) ≈ 7.3 × 10 -3, ϕD(FMN, pH 8) ≈ 4.6 × 10 -3, ϕD(FAD, pH 8) ≈ 3.7 × 10 -4, ϕD(lumichrome, pH 8) ≈ 1.8 × 10 -4, and ϕD(lumiflavin, pH 8) ⩽ 1.1 × 10 -5. In a mass-spectroscopic analysis, the photo-products of FMN dissolved in water (solution pH is 5.6) were identified to be lumichrome and the lumiflavin derivatives dihydroxymethyllumiflavin, formyllumiflavin, and lumiflavin-hydroxy-acetaldehyde. An absorption and emission spectroscopic characterisation of the primary photoproducts of FMN at pH 8 is carried out.

  3. Photo-induced degradation of some flavins in aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Holzer, W. [Institut II-Experimentelle und Angewandte Physik, Universitaet Regensburg, Universitaetsstrasse 31, D-93053 Regensburg (Germany); Shirdel, J. [Institut II-Experimentelle und Angewandte Physik, Universitaet Regensburg, Universitaetsstrasse 31, D-93053 Regensburg (Germany); Zirak, P. [Institut II-Experimentelle und Angewandte Physik, Universitaet Regensburg, Universitaetsstrasse 31, D-93053 Regensburg (Germany); Penzkofer, A. [Institut II-Experimentelle und Angewandte Physik, Universitaet Regensburg, Universitaetsstrasse 31, D-93053 Regensburg (Germany)]. E-mail: alfons.penzkofer@physik.uni-regensburg.de; Hegemann, P. [Institut fuer Biochemie I, Universitaet Regensburg, Universitaetsstrasse 31, D-93053 Regensburg (Germany); Deutzmann, R. [Institut fuer Biochemie I, Universitaet Regensburg, Universitaetsstrasse 31, D-93053 Regensburg (Germany); Hochmuth, E. [Institut fuer Biochemie I, Universitaet Regensburg, Universitaetsstrasse 31, D-93053 Regensburg (Germany)

    2005-01-10

    The blue-light induced photo-degradation of FMN, FAD, riboflavin, lumiflavin, and lumichrome in aqueous solution at pH 8 is studied by measurement of absorption coefficient spectral changes due to continuous excitation at 428 nm. The quantum yields of photo-degradation determined are {phi}{sub D}(riboflavin, pH 8) {approx} 7.8 x 10{sup -3}, {phi}{sub D}(FMN, pH 5.6) {approx} 7.3 x 10{sup -3}, {phi}{sub D}(FMN, pH 8) {approx} 4.6 x 10{sup -3}, {phi}{sub D}(FAD, pH 8) {approx} 3.7 x 10{sup -4}, {phi}{sub D}(lumichrome, pH 8) {approx} 1.8 x 10{sup -4}, and {phi}{sub D}(lumiflavin, pH 8) approx. 1.1 x 10{sup -5}. In a mass-spectroscopic analysis, the photo-products of FMN dissolved in water (solution pH is 5.6) were identified to be lumichrome and the lumiflavin derivatives dihydroxymethyllumiflavin, formyllumiflavin, and lumiflavin-hydroxy-acetaldehyde. An absorption and emission spectroscopic characterisation of the primary photoproducts of FMN at pH 8 is carried out.

  4. Electrodialysis potential for fractionation of multicomponent aqueous solutions

    Directory of Open Access Journals (Sweden)

    Grzegorzek Martyna

    2017-01-01

    Full Text Available The paper aimed at the evaluation of the batch electrodialysis (ED run in the course of treatment and desalination of various aqueous mixtures containing both mineral (sodium fluoride, sodium chloride and organic substances (dyes or humic acids. The commercial ED stack (PCCell Bed equipped with standard anion-exchange and cation-exchange membranes or monovalent selective anion-exchange membranes was used. The ED experiments were performed at a constant current density (1.56 or 1.72 mA/cm2. The mechanism of ion migration as well as membrane deposition for variable solution composition and various membrane types was analyzed The calculated mass balance and electrical energy demand for each ED run were helpful in evaluating the membrane fouling intensity. It was found that the presence of organic substances in the treated solution had a minor impact on energy consumption, but rather strongly affected chloride flux. The extent of organics deposition was significantly lower for monovalent selective anion-exchange membranes than for classic anion-exchange membranes.

  5. CHROMIUM (III ADSORPTION FROM AQUEOUS SOLUTION BY Rhizophora apiculata TANNINS

    Directory of Open Access Journals (Sweden)

    C. W. Oo

    2010-06-01

    Full Text Available Adsorption of Cr3+ from aqueous solution by Rhizophora apiculata tannins was investigated in batch shaking experiments. Tannins extracted from R. apiculata mangrove barks was chemically modified with formaldehyde in the basic solution of sodium hydroxide. The performance of the produced adsorbent on the adsorption of Cr3+ was evaluated based on the effect of several parameters like initial pH, adsorbent dosage, initial Cr3+ concentration and contact time. Equilibrium adsorption data was analyzed by Langmuir, Freundlich, Sips and Dubinin-Raduskhevich (D-R isotherms. The fitness of the isotherms to the experimental data was determined by non-linear regression analysis. Adsorption capacity calculated from Langmuir isotherm was found to be 10.14 mg Cr3+/g of adsorbent at optimum adsorption pH of 4.5. Mean energy of adsorption with the value of 10.35 kJ/mol indicated that adsorption Cr3+ on Rhizophora apiculata tannins followed ion-exchange reaction. Kinetic study showed that the adsorption process followed the pseudo second-order kinetic model.   Keywords:  Rhizophora apiculata, tannins, isotherms, kinetic, chromium.

  6. Gamma Radiolysis Studies of Aqueous Solution of Brilliant Green Dye

    Directory of Open Access Journals (Sweden)

    D. V. Parwate

    2011-01-01

    Full Text Available The effect of γ–radiation on colour intensity of aqueous solution of Brilliant Green has been investigated at two different concentrations. The degradation of Brilliant Green (BG has also been investigated in presence of suspended ZnO, by adding different amounts of ZnO. Simultaneously the conductance and pH of each solution system were measured before and after γ-irradiation. All the γ–irradiations were performed at a dose rate of 0.60 kGyhr-1 in GC-900. The maximum dose required for the complete degradation of the dye was found to be 0.39 kGy. G(-dye values were found to decrease with increase in gamma dose and were in the range 4.26 - 12.81. The conductance (7.6 - 25.3 μS and pH values increased marginally with dose for both the concentrations. The rate of decolouration was found to be high at lower doses and the efficiency of dye removal was higher at low concentration of the dye. This may be attributed to the presence of reaction by-products from the destruction of parent compound build up and compete for reaction intermediate species. The rate of reaction and rate constants were calculated and it was found that the degradation reaction follows first order kinetics. It was found that the decolouration percentage was more in dye systems in absence of ZnO.

  7. Electrodialysis potential for fractionation of multicomponent aqueous solutions

    Science.gov (United States)

    Grzegorzek, Martyna; Majewska-Nowak, Katarzyna

    2017-11-01

    The paper aimed at the evaluation of the batch electrodialysis (ED) run in the course of treatment and desalination of various aqueous mixtures containing both mineral (sodium fluoride, sodium chloride) and organic substances (dyes or humic acids). The commercial ED stack (PCCell Bed) equipped with standard anion-exchange and cation-exchange membranes or monovalent selective anion-exchange membranes was used. The ED experiments were performed at a constant current density (1.56 or 1.72 mA/cm2). The mechanism of ion migration as well as membrane deposition for variable solution composition and various membrane types was analyzed The calculated mass balance and electrical energy demand for each ED run were helpful in evaluating the membrane fouling intensity. It was found that the presence of organic substances in the treated solution had a minor impact on energy consumption, but rather strongly affected chloride flux. The extent of organics deposition was significantly lower for monovalent selective anion-exchange membranes than for classic anion-exchange membranes.

  8. Hydroxyl radical induced degradation of salicylates in aerated aqueous solution

    International Nuclear Information System (INIS)

    Szabó, László; Tóth, Tünde; Homlok, Renáta; Rácz, Gergely; Takács, Erzsébet; Wojnárovits, László

    2014-01-01

    Ionizing radiation induced degradation of acetylsalicylic acid, its hydrolysis product salicylic acid and a salicylic acid derivative 5-sulpho-salicylic acid, was investigated in dilute aqueous solutions by UV–vis spectrophotometry, HPLC separation and diode-array or MS/MS detection, chemical oxygen demand, total organic carbon content and by Vibrio fischeri toxicity measurements. Hydroxyl radicals were shown to degrade these molecules readily, and first degradation products were hydroxylated derivatives in all cases. Due to the by-products, among them hydrogen peroxide, the toxicity first increased and then decreased with the absorbed dose. With prolonged irradiation complete mineralization was achieved. - Highlights: • In OH induced reactions of salicylates first products are hydroxylated derivatives. • With prolonged irradiation dihydroxy derivatives also form. • In aerated solutions the one-electron oxidant OH induces 3–4 oxidations. • Toxicity first increases and then decreases with dose mainly due to H 2 O 2 formation. • The toxicity in tap water is smaller than in pure water

  9. Interaction of gypsum with lead in aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Astilleros, J.M., E-mail: jmastill@geo.ucm.es [Dpto. Cristalografia y Mineralogia, Universidad Complutense de Madrid, Jose Antonio Novais, 2, E-28040 Madrid (Spain); Godelitsas, A. [Department of Mineralogy and Petrology, Faculty of Geology and Geoenvironment, University of Athens, Panepistimioupoli Zographou, 15784 Athens (Greece); Rodriguez-Blanco, J.D. [School of Earth and Environments, Faculty of Environment, University of Leeds, Leeds LS2 9JT (United Kingdom); Fernandez-Diaz, L. [Dpto. Cristalografia y Mineralogia, Universidad Complutense de Madrid, Jose Antonio Novais, 2, E-28040 Madrid (Spain); Prieto, M. [Dpto. de Geologia, Universidad de Oviedo, E-30005 Oviedo (Spain); Lagoyannis, A.; Harissopulos, S. [Tandem Accelerator Laboratory, Institute of Nuclear Physics, NCSR ' Demokritos' , GR-15310 Attiki (Greece)

    2010-07-15

    Sorption processes on mineral surfaces are a critical factor in controlling the distribution and accumulation of potentially harmful metals in the environment. This work investigates the effectiveness of gypsum (CaSO{sub 4}.2H{sub 2}O) to sequester Pb. The interaction of gypsum fragments with Pb-bearing solutions (10, 100 and 1000 mg/L) was monitored by performing macroscopic batch-type experiments conducted at room temperature. The aqueous phase composition was periodically determined by Atomic Absorption Spectrometry (AAS), Ion Chromatography (IC) and Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES). Regardless of the [Pb{sub aq}]{sub initial}, a [Pb{sub aq}]{sub final} < 4 mg/L was always reached. The uptake process was fast (t < 1 h) for [Pb{sub aq}]{sub initial} {>=} 100 mg/L and significantly slower (t > 1 week) for [Pb{sub aq}]{sub initial} = 10 mg/L. Speciation calculations revealed that after a long time of interaction (1 month), all the solutions reached equilibrium with respect to both gypsum and anglesite. For [Pb{sub aq}]{sub initial} {>=} 100 mg/L, sorption takes place mainly via the rapid dissolution of gypsum and the simultaneous formation of anglesite both on the gypsum surface and in the bulk solution. In the case of [Pb{sub aq}]{sub initial} = 10 mg/L, no anglesite precipitation was observed, but surface spectroscopy (proton Rutherford Backscattering Spectroscopy, p-RBS) confirmed the formation of Pb-bearing surface layers on the (0 1 0) gypsum surface in this case also. This study shows that the surface of gypsum can play an important role in the attenuation of Pb in contaminated waters.

  10. The reducibility of sulphuric acid and sulphate in aqueous solution

    International Nuclear Information System (INIS)

    Grauer, R.

    1991-07-01

    In connection with the Swedish project for final storage of spent fuel elements it was necessary to assess whether dissolved sulphate can corrode the copper canister. A simple reaction between copper and sulphate is thermodynamically impossible, but copper can react to give copper sulphide if an additional electron donor such as iron(II) is available. The problem was extended to the more general question of the reducibility of sulphur(VI) in dilute aqueous solution. Chemical reduction of sulphate does not take place in dilute solution at temperatures below 100 o C. In experiments on the reduction of sulphates under hydrothermal conditions a reaction only takes place at temperatures above 275-300 o C. The oxidising action of sulphuric acid on metals becomes perceptible only at acid concentrations over 45-50%. In experiments on the cathodic reduction of 74% sulphuric acid the formation of hydrogen sulphide and elementary sulphur starts, depending on the current density, at 50-130 o C, and polarographic measurements suggest that the reducible species is not the hydrogen sulphate ion but molecular sulphuric acid. The resistance of copper to oxygen-free sulphuric acid up to a concentration of 60% is well-known. Numerous processes in industrial electrochemistry take place in sulphuric acid or sulphate electrolytes. The reversible metal/metal-sulphate electrodes of lead and cadmium are unstable relative to the corresponding metal sulphides. Nevertheless the reversible lead sulphate electrode does not fail from sulphide formation. All these facts confirm that sulphur(VI) in dilute solution is completely inert towards chemical reducing agents and also to cathodic reduction. Thus corrosion of copper by sulphate under final-storage conditions and in the absence of sulphate reducing bacteria can be almost certainly be ruled out. (author) 5 figs., 85 refs

  11. Degradation of di-2-ethylhexyl phthalate in aqueous solution by advanced oxidation process

    Directory of Open Access Journals (Sweden)

    Maryam Zarean

    2015-01-01

    Conclusion: It could be found that the UV/O3 process is a method for DEHP degradation in aqueous solution and may be recommended as a supplement with other processes for treatment of solutions containing low DEHP concentrations.

  12. Symbiodinium isolation by NaOH treatment.

    Science.gov (United States)

    Zamoum, Thamilla; Furla, Paola

    2012-11-15

    The presence of photosynthetic zooxanthellae (dinoflagellates) in the tissue of many cnidarians is the main reason for their ecological success (i.e. coral reefs). It could also be the main cause of their demise, as the worldwide bleaching of reef-building coral is nothing less than the breakdown of this symbiotic association. The stability of this relationship is the principal marker for the biomonitoring of cnidarian health. We have therefore developed a new, simple method to isolate zooxanthellae in a few steps using NaOH solution. The protocol was validated in three symbiotic cnidarian species: a sea anemone, a gorgonian and a coral. Our method allows the isolation of intact and viable zooxanthellae with better yields than classic methods, especially for species with a calcareous skeleton. Moreover, the isolated zooxanthellae were free of host nucleic contaminants, facilitating subsequent specific molecular analyses.

  13. A thermodynamic model for aqueous solutions of liquid-like density

    Energy Technology Data Exchange (ETDEWEB)

    Pitzer, K.S.

    1987-06-01

    The paper describes a model for the prediction of the thermodynamic properties of multicomponent aqueous solutions and discusses its applications. The model was initially developed for solutions near room temperature, but has been found to be applicable to aqueous systems up to 300/sup 0/C or slightly higher. A liquid-like density and relatively small compressibility are assumed. A typical application is the prediction of the equilibrium between an aqueous phase (brine) and one or more solid phases (minerals). (ACR)

  14. XPS study of the passive layers formed on lead in aqueous nitrate solutions

    International Nuclear Information System (INIS)

    Uchida, Miho; Okuwaki, Akitsugu

    1997-01-01

    The analysis of the lead surface immersed in aqueous nitrate solutions by X-ray photoelectron spectroscopy (XPS) shows the formation of passive oxide layer containing nitrogen compound. The oxide layer formed on the lead surface in aqueous ammonium nitrate solution was hydrolyzed and cracked. (author)

  15. Adsorption of Cu 2+ , As 3+ and Cd 2+ ions from aqueous solution ...

    African Journals Online (AJOL)

    The adsorption of Cu2+, Cd2+ and As3+ ions on eggshell from aqueous solution was studied under batch conditions at 30, 40, 50 and 60oC and concentrations of 10, 20, 30, 60 and 80 mg/l. The partition coefficient for the ions between aqueous solution and chicken eggshell increased with time and with increase in the ...

  16. Highly efficient fluoride adsorption from aqueous solution by nepheline prepared from kaolinite through alkali-hydrothermal process.

    Science.gov (United States)

    Wang, Hao; Feng, Qiming; Liu, Kun; Li, Zishun; Tang, Xuekun; Li, Guangze

    2017-07-01

    A direct alkali-hydrothermal induced transformation process was adopted to prepare nepheline from raw kaolinite (shortened form RK in this paper) and NaOH solution in this paper. Structure and morphology characterizations of the synthetic product showed that the nepheline possessed high degree of crystallinity and uniform surface morphology. Specific surface area of nepheline is 18 m 2 /g, with a point of zero charge at around pH 5.0-5.5. The fluoride (F - ions) adsorption by the synthetic nepheline (shortened form SN in this paper) from aqueous solution was also investigated under different experimental conditions. The adsorption process well matched the Langmuir isotherm model with an amazing maximum adsorption capacity of 183 mg/g at 323 K. The thermodynamic parameters (ΔG 0 , ΔH 0 , and ΔS 0 ) for adsorption on SN were also determined from the temperature dependence. The adsorption capacities of fluoride on SN increased with increasing of temperature and initial concentration. Initial pH value also had influence on adsorption process. Adsorption of fluoride was rapidly increased in 5-60 min and thereafter increased slowly to reach the equilibrium in about 90-180 min under all conditions. The adsorption followed a pseudo-second order rate law. Copyright © 2017 Elsevier Ltd. All rights reserved.

  17. Adsorption study of selenium ions from aqueous solutions using MgO nanosheets synthesized by ultrasonic method

    Energy Technology Data Exchange (ETDEWEB)

    Cui, Wenwen; Li, Ping; Wang, Zheming; Zheng, Shili; Zhang, Yi

    2018-01-01

    tMgO nanosheets with thickness ranges of 3–10 molecule layers and high specific area (166.44 m2g-1)were successfully fabricated by an ultrasound-assisted exfoliation method and used as adsorbent forthe removal of both selenite (Se(IV)) and selenate (Se(VI)) from aqueous solutions. The resulting MgOnanosheets displayed high maximum adsorption capacities of 103.52 and 10.28 mg g-1for Se(IV) andSe(VI), respectively. ATR-FTIR and XPS spectroscopic results suggested that both Se(IV) and Se(VI) formedinner-sphere surface complexes on MgO nanosheets under the present experimental conditions. Fur-thermore, high adsorption capacity for Se(IV/VI) in the presence of coexistent anions (SO42-, PO43-, Cl-,and F-) and efficient regeneratability of adsorbent by NaOH solution were observed in the competitiveadsorption and regeneration steps. The simple one-step synthesis process of MgO nanosheets and highadsorption capacities offer a promising method for Se(IV/VI) removal in water treatment.

  18. Separation of compounds with multiple -OH groups from dilute aqueous solutions via complexation with organoboronate. [1,2-propanediol

    Energy Technology Data Exchange (ETDEWEB)

    Chow, Tina Kuo Fung.

    1992-05-01

    The complexing extractant agent investigated in this work is 3-nitrophenylboronic acid (NPBA) in its anionic form (NPB). NPBA and Aliquat 336 (quaternary amine) is dissolved in 2-ethyl-l-hexanol, and the extractant is contacted with aq. NaOH. Solutes investigated were 1,2-propanediol, glycerol, fructose, sorbitol and lactic acid. Batch extraction experiments were performed at 25{degree}C. Partition coefficients, distribution ratios and loadings are reported for varying concentrations of solute and NPB. All solutes complexed with NPB{sup {minus}}, with all complexes containing only one NPB{sup {minus}} per complex. The 1:1 complexation constants for the solutes glycerol, fructose and sorbitol follow trends similar to complexation with B(OH){sub 4}{sup {minus}} (aq.), i.e. the complexation constants increase with increasing number of {minus}OH groups available for complexation. Assumption of 1:1 complex is not valid for 1, 2-propanediol, which showed overloading (more than one mole of solute complexed to one mole NPB{sup {minus}}) at higher concentrations. The {minus}OH group on the NPB{sup {minus}} which is left uncomplexed after one solute molecule had bound to the other two {minus}OH groups may be responsible for the overloading. Overloading is also observed in extraction of tactic acid, but through a different mechanism. It was found that TOMA{sup +} can extract lactic acid to an extent comparable to the uptake of lactic acid by NPB{sup {minus}}. The complexation is probably through formation of an acid-base ion pair. Losses of NPBA into the aqueous phase could lead to problems, poor economics in industrial separation processes. One way of overcoming this problem would be to incorporate the NPBA onto a solid support.

  19. Influence of density on radiation-chemical yield of molecular hydrogen formed at radiolysis of aqueous solution of NaOH

    International Nuclear Information System (INIS)

    Jafarov, Y.D.; Hajiyeva, S.R.; Ramazanova, N.K.; Aliyev, S.M.; Alasgarov, A.M.

    2014-01-01

    Full text : In atom and nuclear energy the specialists knowledge about radiation-chemical yield of the initial products formed under the influence of ionizing rays on water is of great importance from the point of security. The radiation-chemical yields of molecular hydrogen have been defined according to the graph and the obtained results

  20. Speciation analysis on Eu(3) in aqueous solution using laser-induced breakdown spectroscopy

    International Nuclear Information System (INIS)

    Hotokezaka, H.; Tanaka, S.; Nagasaki, S.

    2001-01-01

    Investigation of the chemical behaviour of lanthanides and actinides in the geosphere is important for the safety assessment of high-level radioactive waste disposal. However, determination of speciation for lanthanides and actinides is difficult, because it is too hard to distinguish between metal ion and colloidal metal in aqueous solution. Laser-induced breakdown spectroscopy (LIBS) can detect both ions and microparticles of metals in aqueous solution, especially, high sensitive to microparticles. In this study, we analysed Eu(III) ion and Eu 2 O 3 particle in aqueous solution by LIBS, and measured the hydrolysis behaviour of Eu(III) in aqueous solution. Furthermore, we tried to detect the plasma emission of Eu(III) ions sorbed on TiO 2 particles, and also tried to observe the adsorption behaviour of Eu(III) ions onto TiO 2 particles in aqueous solution. (authors)

  1. Morphology control of brushite prepared by aqueous solution synthesis

    Directory of Open Access Journals (Sweden)

    T. Toshima

    2014-03-01

    Full Text Available Dicalcium phosphate dihydrate (DCPD, CaHPO4·2H2O, also known as brushite, is one of the important bioceramics due to not only diseases factors such as kidney stone and plaque formation but also purpose as fluoride insolubilization material. It is used medicinally to supply calcium, and is of interest for its unique properties in biological and pathological mineralization. It is important to control the crystal morphology of brushite since its chemical reactivity depends strongly on its surface properties; thus, its morphology is a key issue for its applications as a functional material or precursor for other bioceramics. Here, we report the effects of the initial pH and the Ca and phosphate ion concentrations on the morphology of DCPD particles during aqueous solution synthesis. Crystal morphologies were analyzed by scanning electron microscopy and X-ray diffraction. The morphology phase diagram of DCPD crystallization revealed that increasing the initial pH and/or ion concentration transformed DCPD morphology from petal-like into plate-like structures.

  2. Methylene blue adsorption from aqueous solution by dehydrated peanut hull

    Energy Technology Data Exchange (ETDEWEB)

    Ozer, Dursun [Department of Chemical Engineering, Firat University, 23279 Elazig (Turkey); Dursun, Guelbeyi [Department of Chemical Engineering, Firat University, 23279 Elazig (Turkey)]. E-mail: gdursun@firat.edu.tr; Ozer, Ahmet [Department of Chemical Engineering, Firat University, 23279 Elazig (Turkey)

    2007-06-01

    Dyes are colour organic compounds which can colorize the other substances. These substances usually presents in the effluent water of many industries, such as textiles, leather, paper, printing and cosmetics. To observe the potential feasibility of removing colour, peanut hull as an agricultural by-product was dehydrated with sulphuric acid (DPH) and used for adsorption of methylene blue (MB) from aqueous solution. The effects of various parameters such as initial methylene blue concentrations, temperatures and particle sizes were examined and optimal experimental conditions were determined. Adsorption data were well described by the Langmuir model, although they could be modelled by the Freundlich model as well. The adsorption process followed the pseudo-second order kinetic model. The mass transfer model as intraparticle diffusion was applied to the experimental data to examine the mechanisms of rate controlling step. It was found that at the higher initial MB concentration, intraparticle diffusion is becoming significant controlling step. The thermodynamic constants of the adsorption process were also evaluated by using the Langmuir constants related to the equilibrium of adsorption at different temperatures. The results in this study indicated that dehydrated peanut hull was a good adsorbent for removing methylene blue.

  3. Nitroimidazoles adsorption on activated carbon cloth from aqueous solution.

    Science.gov (United States)

    Ocampo-Pérez, R; Orellana-Garcia, F; Sánchez-Polo, M; Rivera-Utrilla, J; Velo-Gala, I; López-Ramón, M V; Alvarez-Merino, M A

    2013-07-01

    The objective of this study was to analyze the equilibrium and adsorption kinetics of nitroimidazoles on activated carbon cloth (ACC), determining the main interactions responsible for the adsorption process and the diffusion mechanism of these compounds on this material. The influence of the different operational variables, such as ionic strength, pH, temperature, and type of water (ultrapure, surface, and waste), was also studied. The results obtained show that the ACC has a high capacity to adsorb nitroimidazoles in aqueous solution. Electrostatic interactions play an important role at pHpH values. Modifications of the ACC with NH3, K2S2O8, and O3 demonstrated that its surface chemistry plays a predominant role in nitroimidazole adsorption on this material. The adsorption capacity of ACC is considerably high in surface waters and reduced in urban wastewater, due to the levels of alkalinity and dissolved organic matter present in the different types of water. Finally, the results of applying kinetic models revealed that the global adsorption rate of dimetridazole and metronidazole is controlled by intraparticle diffusion. Copyright © 2013 Elsevier Inc. All rights reserved.

  4. Activated carbons employed to remove ionic liquids from aqueous solutions

    International Nuclear Information System (INIS)

    Hassan, S.; Farooq, A.; Ahmad, M.A.; Irfan, N.; Tufail, M.

    2011-01-01

    Imidazolium and pyridinium based ionic liquids (ILs) have been separated from aqueous solutions by adsorption using a raw Chinese activated carbon (CAC), a bleached Chinese activated carbon (BAC) and an acid treated Chinese activated carbon (AAC) as adsorbent. Adsorption isotherms data of ionic liquids on activated carbons has been obtained. The influence of both cations and anions was analyzed by studying three different ILs. The role of surface chemistry of the adsorbent was also examined using activated carbons modified by oxidative treatments. The BET surface area of activated carbons was measured by nitrogen adsorption. The results of this work indicate that activated carbon is an attractive adsorbent to remove ionic liquids from water streams. It has also been demonstrated that the adsorption of hydrophilic ionic liquids can be improved by modifying the amount and nature of oxygen groups on the activated carbon surface specially by increasing basic groups. The adsorption data for isotherms was studied at acidic, neutral and basic pH values. (author)

  5. The Interaction of Sorbitol with Caffeine in Aqueous Solution.

    Science.gov (United States)

    Tavagnacco, Letizia; Brady, John W; Cesàro, Attilio

    2013-09-01

    Molecular dynamics simulations were carried out on a system of caffeine interacting with the sugar alcohol sorbitol. The system examined had a caffeine concentration 0.083 m and a sugar concentration 1.08 m. The trajectories of all molecules in the system were collected over a period of 80 ns and analyzed to determine whether there is any tendency for sorbitol to bind to caffeine, and if so, by what mechanism. The results show that the sorbitol molecules have an affinity for the caffeine molecules and that the binding occurred by the interaction of the aliphatic hydrophobic protons of the sugar with the caffeine face. This intermolecular association via face-to-face stacking, as suggested by simulation studies, is similar to that found for sucrose and for D-glucose, which overwhelmingly exists in the pyranose ring chair form in aqueous solution, as well as for caffeine-caffeine association. The sorbitol molecules, however, exist as relatively extended chains and are, therefore, topologically quite different from the sugars sucrose and glucose. The comparison of the average conformation of sorbitol molecules bound to caffeine with that of molecules in the free state shows a substantial similarity.

  6. Radical-induced dephosphorylation of fructose phosphates in aqueous solution

    International Nuclear Information System (INIS)

    Zegota, H.; Sonntag, C. von

    1981-01-01

    Oxygen free N 2 O-saturated aqueous solutions of D-fructose-1-phosphate and D-fructose-6-phosphate were γ-irradiated. Inorganic phosphate and phosphate free sugars (containing four to six carbon atoms) were identified and their G-values measured. D-Fructose-1-phosphate yields (G-values in parentheses) inorganic phosphate (1.6), hexos-2-ulose (0.12), 6-deoxy-2,5-hexodiulose (0.16), tetrulose (0.05) and 3-deoxytetrulose (0.15). D-Fructose-6-phosphate yields inorganic phosphate (1.7), hexos-5-ulose (0.1), 6-deoxy-2,5-hexodiulose (0.36), 3-deoxy-2,5-hexodiulose and 2-deoxyhexos-5-ulose (together 0.18). On treatment with alkaline phosphatase further deoxy sugars were recognized and in fructose-1-phosphate G(6-deoxy-2,5-hexodiulose) was increased to a G-value of 0.4. Dephosphorylation is considered to occur mainly after OH attack at C-5 and C-1 in fructose-1-phosphate and at C-5 and C-6 in fructose-6-phosphate. Reaction mechanisms are discussed. (orig.)

  7. Photo-induced reduction of flavin mononucleotide in aqueous solutions

    International Nuclear Information System (INIS)

    Song, S.-H.; Dick, B.; Penzkofer, A.

    2007-01-01

    The photo-induced reduction of flavin mononucleotide (FMN) in aqueous solutions is studied by absorption spectra measurement under aerobic and anaerobic conditions. Samples without exogenous reducing agent and with the exogenous reducing agents ethylene-diamine-tetraacetic acid (EDTA) and dithiothreitol (DTT) are investigated. Under anaerobic conditions the photo-induced reduction with and without reducing agents is irreversible. Under aerobic conditions the photo-reduction without added reducing agent is small compared to the photo-degradation, and the photo-reduction of FMN by the reducing agents is reversible (re-oxidation in the dark). During photo-excitation of FMN the dissolved oxygen is consumed by singlet oxygen formation and subsequent chemical reaction. After light switch-off slow re-oxidation (slow absorption recovery) occurs due to air in-diffusion from surface. EDTA degradation by FMN excitation leads to oxygen scavenging. The quantum efficiencies of photo-reduction under aerobic and anaerobic conditions are determined. The re-oxidation of reduced FMN under aerobic conditions and due to air injection is investigated

  8. Observation of electron-transfer-mediated decay in aqueous solution

    Science.gov (United States)

    Unger, Isaak; Seidel, Robert; Thürmer, Stephan; Pohl, Marvin N.; Aziz, Emad F.; Cederbaum, Lorenz S.; Muchová, Eva; Slavíček, Petr; Winter, Bernd; Kryzhevoi, Nikolai V.

    2017-07-01

    Photoionization is at the heart of X-ray photoelectron spectroscopy (XPS), which gives access to important information on a sample's local chemical environment. Local and non-local electronic decay after photoionization—in which the refilling of core holes results in electron emission from either the initially ionized species or a neighbour, respectively—have been well studied. However, electron-transfer-mediated decay (ETMD), which involves the refilling of a core hole by an electron from a neighbouring species, has not yet been observed in condensed phase. Here we report the experimental observation of ETMD in an aqueous LiCl solution by detecting characteristic secondary low-energy electrons using liquid-microjet soft XPS. Experimental results are interpreted using molecular dynamics and high-level ab initio calculations. We show that both solvent molecules and counterions participate in the ETMD processes, and different ion associations have distinctive spectral fingerprints. Furthermore, ETMD spectra are sensitive to coordination numbers, ion-solvent distances and solvent arrangement.

  9. Radiolytic studies of the cumyloxyl radical in aqueous solutions

    International Nuclear Information System (INIS)

    Neta, P.; Dizdaroglu, M.; Simic, M.G.

    1984-01-01

    Formation and reactions of the cumyloxyl radical in aqueous solutions were studied by steady-state and pulse radiolytic techniques. Cumene hydroperoxide reacts with esub(aq)sup(-) (k = 4.4x10 9 M -1 s -1 ) to yield the cumyloxyl radical. The spectrum recorded after the pulse indicates formation of a species absorbing at 250 nm. This product was identified as acetophenone, which is formed by the fragmentation of the cumyloxyl radical. By comparison of the pseudo-first-order rates of esub(aq)sup(-) decay at 600 nm with the rate of production of acetophenone at 245 nm at increasing concentrations of cumene hydroperoxide, it was possible to derive a rate constant of 1.0x10 7 s -1 for the cleavage of cumyloxyl to acetophenone and methyl radical. This value is higher than that measured previously in organic solvents (1x10 6 s -1 ), as expected. HPLC analysis of the radiation products acetophenone and cumyl alcohol permitted determination of rate constants for hydrogen abstraction by the cumyloxyl radical, in competition with the fragmentation. The rate constants for H abstraction from i-PrOH, EtOH, and MeOH by CmO were found to be 9.9x10 6 , 3.8x10 6 , and 8.5x10 5 M -1 s -1 , respectively

  10. THERMODYNAMICS OF ETHANOLAMMONIUM CATIONES DISSOCIATION IN AQUEOUS SOLUTIONS

    Directory of Open Access Journals (Sweden)

    R. E. Khoma

    2017-03-01

    Full Text Available The literature data on the thermodynamics of ethanolamines onium cations dissociation have been systematized and generalized. The correlation between these cations dissociation thermodynamic functions (DH and DS and physicochemical properties (Tmp., Tbp, Pp, lgPow et al. has been revealed. There was a correlation between lipophilicity determined experimentally and calculated by QSAR. For monoethanolammonium, diethanolammonium, and their N-methyl and N-ethyl derivatives it was found dissociation thermodynamic functions to depend on bases lgPow. Acid-base dissociation of TRIS and triethanolamine onium cations does not correspond to said relationship because TRIS (primary amine, TEA (tertiary amine act differently on aqueous solutions of SO2. TEA, unlike MEA, DEA and MMEA, has a salting out effect towards sulfur dioxide because of competing hydration that promotes sulfite «onium» salts hydrolysis. TRIS promotes S(IV → S(VI sulphooxidation, in contrast to another ethanolamines. Enthalpy–enthropy compensation with isothermodynamic temperature 303 K has been recorded. The revealed correlations may be useful in developing of procedures for air sanitary cleaning from acidic gases; chemisorbents immobilized for gas and ion exchange chromatography; potentiometric methods for fluorocomplex acids determinations. The use of monoethanolamine is most promising to obtain chemisorbents because the thermodynamic functions of its onium cation acid-base dissociation are least dependent on temperature compared to other etanolammonium cations.

  11. Sonochemical degradation of organophosphorus pesticide in dilute aqueous solutions

    Institute of Scientific and Technical Information of China (English)

    Robina Farooq; FENG Kai-lin; S. F. Shaukat; HUANG Jian-jun

    2003-01-01

    Ultrasonic irradiation was found to accelerate the rate of hydrolysis of omethoate in aqueous solution over the pH range of 2-12. Process parameters studied include pH, steady-state temperature, concentration, and the type of gases. Greater than 96% hydrolysis was observed in 30 minutes through this process and the rate of destruction increased with the help of more soluble and low thermal inert gas. So with Krypton, omethoate was found to undergo rapid destruction as compared with Argon. In the presence of ultrasound, the observed first-order rate of hydrolysis of omethoate is found to be independent of pH. The formation of transient supercritical water(SCW) appears to be an important factor in the acceleration of chemical reactions in the presence of ultrasound. A detailed chemical reaction mechanism for omethoate destruction in water was formulated. Experimental results and theoretical kinetic mechanism demonstrated that the most of the omethoate undergo destruction inside the cavitating holes. A very less effect of temperature on the degradation of omethoate within a temperature range of 20-70℃ proves that a small quantity of omethoate undergoes secondary destruction in the bulk liquid.

  12. The photochemistry of neptunium in aqueous perchloric acid solutions

    International Nuclear Information System (INIS)

    Friedman, H.A.; Toth, L.M.; Osborne, M.M.

    1979-01-01

    The photochemistry of neptunium ions in aqueous perchloric acid has been investigated using 254 and 300 nm UV radiation. In the absence of other reagents, Np(IV) and (V) oxidized to Np(VI), in a stepwise fashion, with individual quantum efficiencies for each step that vary from 0.02 to 0.004. Decreasing acid concentration favors the Np(IV) → Np(V) reaction whereas it hinders the Np(V) → Np(VI) photo-oxidation. When ethanol, acetaldehyde and other mild reducing agents are added to neptunium-perchloric acid solutions which are then photolyzed, the Np species are reduced to Np(III) in a stepwise fashion with individual quantum efficiencies that vary from 0.07 to 0.006. The overall photoredox reactions of neptunium are subject to competing secondary product reactions that become significant as the photolysis products accumulate. Absorption spectrophotometry was used to monitor the changes in Np oxidation states and reference spectra of the various Np oxidation states are given for 1.0 N HClO 4 . The Np species have absorption bands in the 300 to 1320 nm region that obey Beer's law only when they were properly resolved. (author)

  13. Degradation of thymine in aqueous solution containing 3HHO

    International Nuclear Information System (INIS)

    Yamamoto, Osamu; Fuji, Izumi

    1985-01-01

    Thymine aqueous solutions were prepared at a concentration of 5 x 10 -4 M (contained 14 C-thymine and buffered at pH 7.0) and were irradiated with 60 Co gamma-rays and 3 H beta-rays from 3 HHO, in the presence of N 2 , O 2 , N 2 O or t-BuOH-N 2 . Thin-layer chromatography was carried out bidimensionally and autoradiography was performed. Considerable difference in the dose-yield curves was observed between beta-irradiation and gamma-irradiation. Oxygen enhancement ratio, 1.35 and 1.06 at a dose of 1.5 x 10 3 Gy, were obtained by gamma-rays and by beta-rays, respectively, for thymine degradation. Oxygen effect on product formation was very low in beta-irradiation. The yield of 5-hydroxy-5-methylbarbituric acid + 5-hydroxy-5-methylhydantoin was much higher in beta-irradiation than in gamma-irradiation under N 2 and N 2 O. These results lead to the conclusion that in beta-irradiation there could be a progression of oxidation of materials with some species differed from OH radicals. (author)

  14. Degradation of adenine in aqueous solution containing 3HHO

    International Nuclear Information System (INIS)

    Yamamoto, Osamu; Fuji, Izumi

    1986-01-01

    Aqueous adenine solutions of 5 x 10 -4 M (containing 14 C-adenine and buffered pH 7.0) were irradiated with 60 Co gamma-rays and 3 H beta-rays from tritiated water in the presence of N 2 , O 2 , N 2 O or t-BuOH-N 2 . Thin-layer chromatography (TLC) was carried out bidimensionally for separation of the radiolytically produced products and autoradiography was performed. Considerable differences were observed in the dose-yield curves for the decomposition of adenine and for the product formation between gamma- and beta-radiolyses. As for the degradation yield, oxygen enhancement ratios, 3.19 in gamma-irradiation and 1.08 in beta-irradiation, were obtained at a dose of 3.0 x 10 3 Gy. Similar products were produced both under N 2 and O 2 , but there were found a specific reaction of t-butanol radical with adenine, the high yield of hypoxanthine under N 2 O, and the higher degradation of the TLC origin-fixed products in beta-irradiation. The present results on adenine suggest, as reported previously for thymine, that a specific oxidative species is produced from water in beta-radiolysis but not in gamma-radiolysis. (author)

  15. Structure and dynamics of aqueous solution of uranyl ions

    International Nuclear Information System (INIS)

    Chopra, Manish; Choudhury, Niharendu

    2014-01-01

    The present work describes a molecular dynamics simulation study of structure and dynamics of aqueous solution of uranyl ions in water. Structural properties of the system in terms of radial distribution functions and dynamical characteristics as obtained through velocity autocorrelation function and mean square displacements have been analyzed. The results for radial distribution functions show the oxygen of water to form the first solvation shell at 2.4 Å around the uranium atom, whereas the hydrogen atoms of water are distributed around the uranium atom with the major peak at around 3.0 Å. Analyses of transport behaviors of ions and water through MSD indicates that the diffusion of the uranyl ion is much less as compared to that of the water molecules. It is also observed that the dynamical behavior of water molecules gets modified due to the presence of uranyl ion. The effect of increase in concentration of uranyl ions on the structure and dynamics of water molecules is also studied

  16. Photochemistry and exciplex of the uranyl ion in aqueous solution

    International Nuclear Information System (INIS)

    Marcantonatos, M.D.

    1980-01-01

    The effects of acidity, temperature, self-quenching and H-donor concentration on the luminescent state of the aqua-uranyl(VI) ion have been studied in aqueous acidic nitrate and perchlorate solution. The detailed results cannot be explained by any single simple mechanism such as radiative, non-radiative or spontaneous collisional quenching, or irreversible hydrogen abstraction from water. Quantitative analysis of the results shows a far more complex mechanism, involving the adiabatic formation of the species *UO 2 H 2+ and *U 2 O 4 H 4+ , as already proposed by the author. This mechanism is supported by state and m.o. correlations. The abstraction of hydrogen from water is shown to take place by H atom transfer in a *uranyl-water complex intermediate, rather than by attack of H + on the fully occupied πsub(u) orbitals of uranium(V) in a well-defined uranyl water complex with strong charge transfer character. A qualitative description of the exciplex *U 2 O 4 H 4+ is shown to be possible in a v.b. formalism and the origin of its radiative properties is discussed on this basis. (author)

  17. Cadmium Removal from Aqueous Solutions by Ground Pine Cone

    Directory of Open Access Journals (Sweden)

    H Izanloo, S Nasseri

    2005-01-01

    Full Text Available A study on the removal of cadmium ions from aqueous solutions by pine cone was conducted in batch conditions. Kinetic data and equilibrium removal isotherms were obtained. The influence of different experimental parameters such as contact time, initial concentration of cadmium, pine cone mass and particle size, and temperature on the kinetics of cadmium removal was studied. Results showed that the main parameters that played an important role in removal phenomenon were initial cadmium concentration, particle size and pine cone mass. The necessary time to reach equilibrium was between 4 and 7 hours based on the initial concentration of cadmium. The capacity of cadmium adsorption at equilibrium increased with the decrease of pine cone particle size. The capacity of cadmium adsorption at equilibrium by pine cone increased with the quantity of pine cone introduced (1–4 g/L. Temperature in the range of 20-30°C showed a restricted effect on the removal kinetics (13.56 mg/g at 20°C and a low capacity of adsorption about 11.48 mg/g at 30°C. The process followed pseudo second-order kinetics. The cadmium uptake of pine cone was quantitatively evaluated using adsorption isotherms. Results indicated that the Langmuir model gave a better fit to the experimental data in comparison with the Freundlich equation.

  18. Pulse radiolysis of adrenaline in acid aqueous solutions

    International Nuclear Information System (INIS)

    Gohn, M.; Getoff, N.; Bjergbakke, E.

    1976-01-01

    Pulse radiolysis of adrenaline in acid aqueous solutions (pH 1 to 3) was carried out. The rate constants for the reactions of adrenaline with H and 0H were determined: k(H + adr.) = (0.9 +- 0.1) x 10 9 dm 3 mol -1 s -1 ; k(0H + adr.) = (1.65 +- 0.15) x 10 10 dm 3 mol -1 s -1 . The H-adduct of adrenaline has two lambdasub(max), at 280 and 355 nm, with epsilon 280 = 420 m 2 mol -1 and epsilon 355 = 390 m 2 mol -1 , which disappears according to a first order reaction, k 1 = 1.4 x 10 3 s -1 . The spectra formed by 0H attack was assigned to the corresponding benzoxy radical with absorption maxima at 285 and 365 nm and epsilon 285 = 620 m 2 mol -1 and epsilon 365 = 105 m 2 mol -1 . Due to the overlapping of the intermediates, no decay kinetics could be obtained. (author)

  19. Flash photolysis of chlorine dioxide in aqueous solution

    International Nuclear Information System (INIS)

    Mialocq, Jean-Claude

    1972-01-01

    The primary process when aqueous solutions of chlorine dioxide are flash photo-lysed by light with a wave length greater than 270 nm is: OClO → hν ClO ( 2 Π) + O ( 3 P). The photochemical decomposition is characterized by the formation of small quantities of O ( 3 P) atoms and of equal amounts of chlorine atoms and molecular oxygen, the latter originating in the reaction: ClOO → Cl + O 2 . The isomer ClOO is formed by the germinate recombination of ClO and O, a process which is twice as important as diffusion of the fragments into the mass of the solution and one which represents 30 per cent of the decomposition of the chlorine dioxide. Under our experimental conditions, the lifetime of the ClOO is less than one microsecond. Chlorine atoms are precursors of Cl 2 O 2 , whose UV absorption spectrum has been determined, and which is formed by the reactions: Cl + OClO → Cl 2 O 2 ; Cl + Cl - → Cl 2- ; Cl 2- + OClO → Cl 2 O 2 + Cl - k = (1,0 ±0,1) 10 9 M -1 s -1 . Cl 2 O 2 disappears by a first-order process which leads to the formation of the ions Cl - and ClO 3 - . Competition between the reactions: O ( 3 P) + O 2 → O 3 ; O ( 3 P) + OClO → ClO 3 . ( k OClO + O)/( k O 2 + O) = 1.85±0.25 has been studied and the molar extinction coefficient of ClO 3 determined at its absorption maximum (255 nm): ε 255 nm = (920 ± 90) M -1 cm -1 . (author) [fr

  20. Pulse radiolysis of butyl acrylate in aqueous solution

    International Nuclear Information System (INIS)

    Kujawa, P.; Ulanski, P.; Rosiak, J.M.; Mohid, N.; Zaman, K.; Manshol, W.

    1998-01-01

    The pulse radiolysis of n-butyl acrylate (nBA) in aqueous solution was studied. The rate constant of the reaction of nBA with hydroxyl radicals was calculated as 1.5x10 10 dm 3 mol -1 s -1 . The absorption spectrum of the OH · -nBA adduct appeared to have a broad maximum at 300 nm. This spectrum was attributed to the α-carbon centred radicals. It decayed with the first-order rate constant k=1.5x10 4 s -1 (pH 10.8). The rate constant of the nBA reaction with hydrated electrons was determined as k=1.6x10 10 dm 3 mol -1 s -1 . The spectrum of H · -nBA adduct was similar to that recorded for OH · adduct. It decayed with first-order kinetics at k=1.0x10 4 s -1 . Spectra of the electron adduct were characterised by the band with a maximum at 285 nm (pH 10.0) or at 280 nm (pH 4.0) with ε=10500 dm 3 mol -1 cm -1 . In acidic solution, radical anion formed upon addition of hydrated electrons to the nBA molecule, undergoes fast, reversible protonation. The decay of the reversibly protonated electron adduct was a second-order process at k=2.5x10 9 dm 3 mol -1 s -1 . This reaction took place at the carbonyl oxygen. Slow, irreversible protonation of the electron adduct at high pH takes place at the β-carbon atom at k=2.9x10 4 s -1

  1. Glycine phases formed from frozen aqueous solutions: Revisited

    Energy Technology Data Exchange (ETDEWEB)

    Surovtsev, N. V. [Institute of Automation and Electrometry, Siberian Branch of Russian Academy of Sciences, Novosibirsk 630090 (Russian Federation); Novosibirsk State University, Novosibirsk 630090 (Russian Federation); Adichtchev, S. V.; Malinovsky, V. K. [Institute of Automation and Electrometry, Siberian Branch of Russian Academy of Sciences, Novosibirsk 630090 (Russian Federation); Ogienko, A. G.; Manakov, A. Yu. [Novosibirsk State University, Novosibirsk 630090 (Russian Federation); Nikolaev Institute of Inorganic Chemistry, Siberian Branch of Russian Academy of Sciences, Novosibirsk 630090 (Russian Federation); Drebushchak, V. A. [Novosibirsk State University, Novosibirsk 630090 (Russian Federation); Institute of Geology and Mineralogy, Siberian Branch of Russian Academy of Sciences, Novosibirsk 630090 (Russian Federation); Ancharov, A. I.; Boldyreva, E. V. [Novosibirsk State University, Novosibirsk 630090 (Russian Federation); Institute of Solid Chemistry and Mechanochemistry, Siberian Branch of Russian Academy of Sciences, Novosibirsk 630090 (Russian Federation); Yunoshev, A. S. [Novosibirsk State University, Novosibirsk 630090 (Russian Federation); Lavrentiev Institute of Hydrodynamics, Siberian Branch of Russian Academy of Sciences, Novosibirsk 630090 (Russian Federation)

    2012-08-14

    Glycine phases formed when aqueous solutions were frozen and subsequently heated under different conditions were studied by Raman scattering, x-ray diffraction, and differential scanning calorimetry (DSC) techniques. Crystallization of ice I{sub h} was observed in all the cases. On cooling at the rates of 0.5 K/min and 5 K/min, glassy glycine was formed as an intermediate phase which lived about 1 min or less only, and then transformed into {beta}-polymorph of glycine. Quench cooling of glycine solutions (15% w/w) in liquid nitrogen resulted in the formation of a mixture of crystalline water ice I{sub h} and a glassy glycine, which could be preserved at cryogenic temperatures (80 K) for an indefinitely long time. This mixture remained also quite stable for some time after heating above the cryogenic temperature. Subsequent heating under various conditions resulted in the transformation of the glycine glass into an unknown crystalline phase (glycine 'X-phase') at 209-216 K, which at 218-226 K transformed into {beta}-polymorph of glycine. The 'X-phase' was characterized by Raman spectroscopy; it could be obtained in noticeable amounts using a special preparation technique and tentatively characterized by x-ray powder diffraction (P2, a= 6.648 A, b= 25.867 A, c= 5.610 A, {beta}= 113.12 Masculine-Ordinal-Indicator ); the formation of 'X-phase' from the glycine glassy phase and its transformation into {beta}-polymorph were followed by DSC. Raman scattering technique with its power for unambiguous identification of the crystalline and glassy polymorphs without limitation on the crystallite size helped us to follow the phase transformations during quenching, heating, and annealing. The experimental findings are considered in relation to the problem of control of glycine polymorphism on crystallization.

  2. Removal mechanism of phosphate from aqueous solution by fly ash.

    Science.gov (United States)

    Lu, S G; Bai, S Q; Zhu, L; Shan, H D

    2009-01-15

    This work studied the effectiveness of fly ash in removing phosphate from aqueous solution and its related removal mechanism. The adsorption and precipitation of phosphate by fly ash were investigated separately in order to evaluate their role in the removal of phosphate. Results showed that the removal of phosphate by fly ash was rapid. The removal percentage of phosphate in the first 5min reached 68-96% of the maximum removal of phosphate by fly ash. The removal processes of phosphate by fly ash included a fast and large removal representing precipitation, then a slower and longer removal due to adsorption. The adsorption of phosphate on fly ash could be described well by Freundlich isotherm equation. The pH and Ca2+ concentration of fly ash suspension were decreased with the addition of phosphate, which suggests that calcium phosphate precipitation is a major mechanism of the phosphate removal. Comparison of the relative contribution of the adsorption and precipitation to the total removal of phosphate by fly ash showed that the adsorption accounted for 30-34% of the total removal of phosphate, depending on the content of CaO in fly ash. XRD patterns of the fly ash before and after phosphate adsorption revealed that phosphate salt (CaHPO4 x 2H2O) was formed in the adsorption process. Therefore, the removal of phosphate by fly ash can be attributed to the formation of phosphate precipitation as a brushite and the adsorption on hydroxylated oxides. The results suggested that the use of fly ash could be a promising solution to the removal of phosphate in the wastewater treatment and pollution control.

  3. Glycine phases formed from frozen aqueous solutions: Revisited

    Science.gov (United States)

    Surovtsev, N. V.; Adichtchev, S. V.; Malinovsky, V. K.; Ogienko, A. G.; Drebushchak, V. A.; Manakov, A. Yu.; Ancharov, A. I.; Yunoshev, A. S.; Boldyreva, E. V.

    2012-08-01

    Glycine phases formed when aqueous solutions were frozen and subsequently heated under different conditions were studied by Raman scattering, x-ray diffraction, and differential scanning calorimetry (DSC) techniques. Crystallization of ice Ih was observed in all the cases. On cooling at the rates of 0.5 K/min and 5 K/min, glassy glycine was formed as an intermediate phase which lived about 1 min or less only, and then transformed into β-polymorph of glycine. Quench cooling of glycine solutions (15% w/w) in liquid nitrogen resulted in the formation of a mixture of crystalline water ice Ih and a glassy glycine, which could be preserved at cryogenic temperatures (80 K) for an indefinitely long time. This mixture remained also quite stable for some time after heating above the cryogenic temperature. Subsequent heating under various conditions resulted in the transformation of the glycine glass into an unknown crystalline phase (glycine "X-phase") at 209-216 K, which at 218-226 K transformed into β-polymorph of glycine. The "X-phase" was characterized by Raman spectroscopy; it could be obtained in noticeable amounts using a special preparation technique and tentatively characterized by x-ray powder diffraction (P2, a = 6.648 Å, b = 25.867 Å, c = 5.610 Å, β = 113.12°); the formation of "X-phase" from the glycine glassy phase and its transformation into β-polymorph were followed by DSC. Raman scattering technique with its power for unambiguous identification of the crystalline and glassy polymorphs without limitation on the crystallite size helped us to follow the phase transformations during quenching, heating, and annealing. The experimental findings are considered in relation to the problem of control of glycine polymorphism on crystallization.

  4. Investigation of the removal of chromium (VI by Nanocomposites Chitosan-tragacanth solution from aqueous solution

    Directory of Open Access Journals (Sweden)

    Adel Almasi Nahnaji

    2016-03-01

    Full Text Available Background: The aim of this study was to investigate the removal of chromium (VI by Nanocomposites Chitosan-tragacanth solution from aqueous solution. Methods: In this study, chitosan-tragacanth nanocomposites were synthesized and analyzed by electron microscopy (SEM, (TEM and Fourier transform spectroscopy (FT-IR for the size and shape of the surface. The nano-composite of chitosan-tragacanth, for the adsorption of chromium (VI in aqueous solution was used as adsorbent. Results: The optimum conditions with multiple experiments to enhance the absorption were evaluated. The highest absorption of Cr (VI was occurred in the adsorbent dosage of 0.2 g, 8 ppm concentration of chromium ions, the pH=6 and also retention time of 50 min; in 298 ˚K temperature. After determining optimal conditions of adsorption, isotherms equations and study and thermodynamic parameters were applied. Adsorption process of chromium (VI on nano-composite chitosan - Tragacanth was conformed with Temkin isotherm. Conclusion: The thermodynamic parameters such as standard Gibbs free energy changes, changes in enthalpy and entropy changes in the standard showed that the adsorption process of Cr (VI is spontaneous and heating, and kinetics studies of models Lagergren, Ho , Alovich and intraparticle is used, the results show that the adsorption kinetics follows the pseudo-second order.

  5. DETERMINING PARAMETERS OF THE DIELECTRIC FUNCTION OF A SUBSTANCE IN AQUEOUS SOLUTION BY SELF-REFERENCED REFLECTION THZ SPECTROSCOPY

    DEFF Research Database (Denmark)

    2008-01-01

    Method and apparatus for determining dielectric function of liquid solutions and thereby concentrations of substances in aqueous solution or the volatile/non-volatile nature of the liquid by self-referenced reflection THz spectroscopy. Having the aqueous solution in any container with a window al....... The invention is particularly useful for determining alcohol (ethanol) content in aqueous solution containing other substances and particles....

  6. Radiation chemistry of aqueous solutions of hydrazine at elevated temperatures: Pt. 2. Solutions containing oxygen

    International Nuclear Information System (INIS)

    Buxton, G.V.; Stuart, C.R.

    1997-01-01

    Here, we investigate the effects of oxygen on the radiation chemistry of hydrazine at elevated temperatures. The chemistry of this system is important to reactor coolant chemistry, particularly under start-up conditions when hydrazine is added to suppress corrosion which would otherwise be caused by the ingress of oxygen. The radiation chemistry of aqueous solutions of hydrazine has been investigated previously in the presence of oxygen by Ershov et al., but only at room temperature. In those experiments, both steady-state γ-radiolysis and pulse radiolysis were used to deduce the mechanism of decomposition of hydrazine in the presence of oxygen. (author)

  7. Nanoscale Stress-Corrosion of Geomaterials in Aqueous Solutions

    Science.gov (United States)

    Criscenti, L. J.; Rimsza, J. M.; Matteo, E. N.; Jones, R. E.

    2017-12-01

    Predicting subcritical crack propagation in low-permeability geo-materials is an unsolved problem crucial to assessing shale caprocks at CO2 sequestration sites, and controlling fracturing for gas and oil extraction. Experiments indicate that chemical reactions at fluid-material interfaces play a major role in subcritical crack growth by weakening the material and altering crack nucleation and growth rates. However, understanding subsurface fracture has been hindered by a lack of understanding of the mechanisms relating chemical environment to mechanical outcome, and a lack of capability directly linking atomistic insight to macroscale observables. We are using both molecular simulation and experiment to develop an atomistic-level understanding of the chemical-mechanical coupling that controls subcritical crack propagation. We are investigating fracture of isotropic silica glass in different environments (air, distilled water, and Na+-rich solutions) and will extend our research to include clay minerals in shales. Molecular simulations are performed with ReaxFF, a reactive force field that allows for explicit modeling of bond breaking and formation processes during crack propagation. A coarse-graining method produces calculated fracture toughness values from the atomistic data. We are performing double cleavage drilled compression (DCDC) experiments in aqueous environmental chambers and monitoring crack propagation with either a confocal or atomic force microscope. Our results show that silica fracture toughness decreases as the environment changes from air to distilled water to Na+-rich solutions. These results suggest that our newly developed computational and experimental techniques can be used to investigate the impact of fluid composition on crack growth in geo-materials and that we will be able to use these methods to understand coupled chemo-mechanical processes and predict crack propagation in shale minerals. Sandia National Laboratories is a multimission

  8. Products of radiation removal of lead from aqueous solutions

    International Nuclear Information System (INIS)

    Drtinova, Barbora; Pospisil, Milan

    2008-01-01

    Full text: Some metal ions, including Pb 2+ can be gradually reduced by primary reducing products of water radiolysis (solvated electrons e aq - and H radicals) to insoluble, easily separable metals. Conditions of water remediation using irradiation with accelerated electrons were studied. The solutions with initial concentration 100 mg/L of Pb(II) (originally nitrate) containing OH radical scavengers were irradiated under intensive agitation in sealed thin-glass ampoules by accelerated electrons (4.5 MeV) from a linear accelerator. Doses ranging from 0.5 to 60 kGy (dose rate of 0.5 kGy/s) determined by an alanine dosimeter were applied. Subsequent process of centrifugation (5000 revs per minute) was used for the separation of product- finely dispersed particles. The changes in metal concentration were determined with error ± 3% by means of atomic absorption spectroscopy with flame atomization. The solid products formed after the irradiation were analyzed by both thermogravimetry and differential thermal analysis. For the pre-irradiated systems were carried out calculations by using PHREEQC in order to determinate the speciation. Without addition of an OH radical scavenger the radiation-induced removal of lead did not occur. The influence of potassium formate HCOOK (1x10 -3 - 4x10 -2 mol/L) and 10% isopropanol as typical OH radical scavengers was individually studied. The lead can be completely removed from aqueous solutions (pH about 5-6) containing 1x10 - :2 mol/L of HCOOK already at the dose of 2.5 kGy. With increasing concentration of HCOOK (1x10 -3 - 4x10 -2 mol/L) increases the amount of Pb(HCOO) + form in the solution before irradiation. The radiation product is metallic lead at low concentration of HCOOK to PbCO 3 at higher concentration of the OH radical scavenger. In the system with isopropanol dominates the form Pb 2+ and the product of radiation reduction is then metallic lead

  9. Removal of anionic dyes (Reactive Black 5 and Congo Red) from aqueous solutions using Banana Peel Powder as an adsorbent.

    Science.gov (United States)

    Munagapati, Venkata Subbaiah; Yarramuthi, Vijaya; Kim, Yeji; Lee, Kwon Min; Kim, Dong-Su

    2018-02-01

    The adsorption characteristics of Reactive Black 5 (RB5) and Cong Red (CR) onto Banana Peel Powder (BPP) from aqueous solution were investigated as a function of pH, contact time, initial dye concentration and temperature. The BPP was characterized by Fourier Transform Infrared Spectroscopy (FTIR) and Scanning Electron Microscopy (SEM) analysis. FTIR results revealed that hydroxyl (-OH), amine (-NH) and carboxyl (-C˭O) functional groups present on the surface of BPP. The SEM results show that BPP has an irregular and porous surface morphology which is adequate for dye adsorption. The equilibrium data were analyzed using Langmuir and Freundlich isotherm models. Experimental results were best represented by the Langmuir isotherm model. The adjustments of models were confirmed by the Chi-square (χ 2 ) test and the correlation coefficients (R 2 ). The maximum monolayer adsorption capacities of RB5 and CR on BPP calculated from Langmuir isotherm model were 49.2 and 164.6mg/g at pH 3.0 and 298K. Experimental data were also tested in terms of adsorption kinetics using pseudo-first-order and pseudo-second-order kinetic models. The results showed that the adsorption processes of both RB5 and CR followed well pseudo-second-order kinetic models. The calculated thermodynamic parameters ΔG°, ΔH° and ΔS° showed that the adsorption of RB5 and CR onto BPP was feasible, spontaneous and endothermic in the temperature range 298-318K. The RB5 and CR were desorbed from BPP using 0.1M NaOH. The recovery for both anionic dyes was found to be higher than 90%. Based on these it can be concluded that BPP can be used as an effective, low cost, and eco-friendly adsorbent for CR removal than RB5 from aqueous solution. Copyright © 2017 Elsevier Inc. All rights reserved.

  10. Densities and apparent molar volumes of atmospherically important electrolyte solutions. 1. The solutes H2SO4, HNO3, HCl, Na2SO4, NaNO3, NaCl, (NH4)2SO4, NH4NO3, and NH4Cl from 0 to 50 °C, including extrapolations to very low temperature and to the pure liquid state, and NaHSO4, NaOH, and NH3 at 25 °C.

    Science.gov (United States)

    Clegg, S L; Wexler, A S

    2011-04-21

    Calculations of the size and density of atmospheric aerosols are complicated by the fact that they can exist at concentrations highly supersaturated with respect to dissolved salts and supercooled with respect to ice. Densities and apparent molar volumes of solutes in aqueous solutions containing the solutes H(2)SO(4), HNO(3), HCl, Na(2)SO(4), NaNO(3), NaCl, (NH(4))(2)SO(4), NH(4)NO(3), and NH(4)Cl have been critically evaluated and represented using fitted equations from 0 to 50 °C or greater and from infinite dilution to concentrations saturated or supersaturated with respect to the dissolved salts. Using extrapolated densities of high-temperature solutions and melts, the relationship between density and concentration is extended to the hypothetical pure liquid solutes. Above a given reference concentration of a few mol kg(-1), it is observed that density increases almost linearly with decreasing temperature, and comparisons with available data below 0 °C suggest that the fitted equations for density can be extrapolated to very low temperatures. As concentration is decreased below the reference concentration, the variation of density with temperature tends to that of water (which decreases as temperature is reduced below 3.98 °C). In this region below the reference concentration, and below 0 °C, densities are calculated using extrapolated apparent molar volumes which are constrained to agree at the reference concentrations with an equation for the directly fitted density. Calculated volume properties agree well with available data at low temperatures, for both concentrated and dilute solutions. Comparisons are made with literature data for temperatures of maximum density. Apparent molar volumes at infinite dilution are consistent, on a single ion basis, to better than ±0.1 cm(3) mol(-1) from 0 to 50 °C. Volume properties of aqueous NaHSO(4), NaOH, and NH(3) have also been evaluated, at 25 °C only. In part 2 of this work (ref 1 ) an ion interaction (Pitzer

  11. The use of CH3OH additive to NaOH for etching alpha particle tracks in a CR-39 plastic nuclear track detector

    International Nuclear Information System (INIS)

    Ashry, A.H.; Abdalla, A.M.; Rammah, Y.S.; Eisa, M.; Ashraf, O.

    2014-01-01

    Fast detection of alpha particles in CR-39 detectors was investigated using a new chemical etchant. 252 Cf and 241 Am sources were used for irradiating samples of CR-39 SSNTDs with fission fragments and alpha particles in air at normal temperature and pressure. A series of experimental chemical etching are carried out using new etching solution (8 ml of 10N NaOH+1 ml CH 3 OH) at 60 °C to detect alpha particle in short time in CR-39 detectors. Suitable analyzing software has been used to analyze experimental data. From fission and alpha track diameters, the value of bulk etching rate is equal to 2.73 μm/h. Both the sensitivity and etching efficiency were found to vary with the amount of methanol in the etching solution. Pure NaOH was used as a control to compare with the result from etching in NaOH with different concentrations of CH 3 OH. The etching efficiency is determined and compared with conventional aqueous solution of 6.25N NaOH at 70 °C for etching time equals 5 h. In this study, the obtained etching efficiency shows a considerable agreement with the previous work. - Highlights: • The value of bulk etching rate is equal to 2.73 μm/h. • Fast detection of alpha particles in CR-39 detectors. • Samples of CR-39 have been irradiated with fission fragments. • Etching efficiency was determined

  12. Biosorption of chromium (VI) from aqueous solutions and ANN modelling.

    Science.gov (United States)

    Nag, Soma; Mondal, Abhijit; Bar, Nirjhar; Das, Sudip Kumar

    2017-08-01

    The use of sustainable, green and biodegradable natural wastes for Cr(VI) detoxification from the contaminated wastewater is considered as a challenging issue. The present research is aimed to assess the effectiveness of seven different natural biomaterials, such as jackfruit leaf, mango leaf, onion peel, garlic peel, bamboo leaf, acid treated rubber leaf and coconut shell powder, for Cr(VI) eradication from aqueous solution by biosorption process. Characterizations were conducted using SEM, BET and FTIR spectroscopy. The effects of operating parameters, viz., pH, initial Cr(VI) ion concentration, adsorbent dosages, contact time and temperature on metal removal efficiency, were studied. The biosorption mechanism was described by the pseudo-second-order model and Langmuir isotherm model. The biosorption process was exothermic, spontaneous and chemical (except garlic peel) in nature. The sequence of adsorption capacity was mango leaf > jackfruit leaf > acid treated rubber leaf > onion peel > bamboo leaf > garlic peel > coconut shell with maximum Langmuir adsorption capacity of 35.7 mg g -1 for mango leaf. The treated effluent can be reused. Desorption study suggested effective reuse of the adsorbents up to three cycles, and safe disposal method of the used adsorbents suggested biodegradability and sustainability of the process by reapplication of the spent adsorbent and ultimately leading towards zero wastages. The performances of the adsorbents were verified with wastewater from electroplating industry. The scale-up study reported for industrial applications. ANN modelling using multilayer perception with gradient descent (GD) and Levenberg-Marquart (LM) algorithm had been successfully used for prediction of Cr(VI) removal efficiency. The study explores the undiscovered potential of the natural waste materials for sustainable existence of small and medium sector industries, especially in the third world countries by protecting the environment by eco-innovation.

  13. Ion-exchange concentration of inorganic anions from aqueous solution

    Directory of Open Access Journals (Sweden)

    L. P. Bondareva

    2016-01-01

    Full Text Available Monitoring of natural waters in the present time - consuming process, the accuracy of which is influenced by many factors: the composition of water, the presence of impurities and "interfering" components. The water sample preparation process includes the step of concentration and separation of ions determined. The most versatile, efficient, and frequently used method is the concentration of inorganic anions from aqueous solutions by ion exchanger, which can optimize the composition of water to the optimal for identification and quantitative determination of anions. The characteristics of sorption chloride, nitrate and sulfate ions of basic anion exchange resin AВ-17 and Purolite A430 were compared in the article. The constants of protolysis of ion exchangers both AB 17 and Purolite A430 are the same and equal 0.037 ± 0,002. The value of total capacity (POE Purolite A430 was 4.3 mmol/g, AB 17 – 3.4 mmol/g. The studied ion exchangers have the same type of ionic groups – quaternary ammonium, but their number and denotes differ. The number of quaternary ammonium groups is higher in Purolite A430, respectively the number of absorbed anions of these ion exchanger is higher. The values of dynamic exchange capacity (DOE of ion exchanger Purolite A430 is higher than these values of AB-17 and equal to 1.48 ± 0.03 mmol / dm3 for chloride ion, 1.50 ± 0.03 mmol / dm3 for nitrate ion, 1.62 ± 0.03 mmol / dm3 for sulfate ion. The values of the POE and DOE of anion-exchange resins Purolite A430 and AV-17 and the characteristics of the individual sorption of chloride, nitrate, sulfate ions showed an advantage of the Purolite for the concentrationing of anions. It is found that times of anions sorption from triple-anion solutions by Purolite A430 are significantly different for different anions, and these times are close for anion-exchanger AV-17. It proves the possibility of quantitative separation and concentration by anion-exchanger Purolite A430.

  14. Method for Non-Invasive Determination of Chemical Properties of Aqueous Solutions

    Science.gov (United States)

    Todd, Paul W. (Inventor); Jones, Alan (Inventor); Thomas, Nathan A. (Inventor)

    2016-01-01

    A method for non-invasively determining a chemical property of an aqueous solution is provided. The method provides the steps of providing a colored solute having a light absorbance spectrum and transmitting light through the colored solute at two different wavelengths. The method further provides the steps of measuring light absorbance of the colored solute at the two different transmitted light wavelengths, and comparing the light absorbance of the colored solute at the two different wavelengths to determine a chemical property of an aqueous solution.

  15. Kinetics of the decomposition and the estimation of the stability of 10% aqueous and non-aqueous hydrogen peroxide solutions

    Directory of Open Access Journals (Sweden)

    Zun Maria

    2014-12-01

    Full Text Available In this study, the stability of 10% hydrogen peroxide aqueous and non-aqueous solutions with the addition of 6% (w/w of urea was evaluated. The solutions were stored at 20°C, 30°C and 40°C, and the decomposition of hydrogen peroxide proceeded according to first-order kinetics. With the addition of the urea in the solutions, the decomposition rate constant increased and the activation energy decreased. The temperature of storage also affected the decomposition of substance, however, 10% hydrogen peroxide solutions prepared in PEG-300, and stabilized with the addition of 6% (w/w of urea had the best constancy.

  16. Adsorption behaviors of trivalent actinides and lanthanides on pyridine resin in lithium chloride aqueous solution

    International Nuclear Information System (INIS)

    Tatsuya Suzuki

    2013-01-01

    The adsorption behaviors of trivalent actinides and lanthanides on pyridine resin in lithium chloride aqueous solution were investigated. The adsorbed amounts of lanthanides and the degree of mutual separation of lanthanides increased with an increase in the concentration of lithium chloride in aqueous solution. The group separation of the trivalent actinides and lanthanides was observed. This separation phenomenon is similar in a hydrochloric acid solution. However, the adsorption behavior of lanthanides in lithium chloride is different from their behavior in a hydrochloric acid solution. This fact shows that the adsorption mechanisms of lanthanides in a lithium chloride aqueous solution and in a hydrochloric acid solution are different; the adsorption mechanisms are attributed to the ion exchange in a hydrochloric acid solution, and to the complex formation with pyridine group in a lithium chloride solution. (author)

  17. REMOVAL OF LEAD(II) IONS FROM AQUEOUS SOLUTIONS ...

    African Journals Online (AJOL)

    Preferred Customer

    lung cancer, convulsion and even death if ingested at elevated levels. ... osmosis have been used for removing heavy metal ions from aqueous media [4-6]. ... organic molecules and silica surface functions, (ii) chlorination of the silica surface ...

  18. Kinetics and Thermodynamics of Sorption of 4-Nitrophenol on Activated Kaolinitic Clay and Jatropha Curcas Activated Carbon from Aqueous Solution

    Directory of Open Access Journals (Sweden)

    Samsudeen Olanrewaju Azeez

    2016-06-01

    Full Text Available Adsorption behaviour of 4-nitrophenol (4-NP on activated kaolinitic clay and Jatropha curcas activated carbon was investigated. The kaolinitic clay and Jatropha curcas were activated with 1 M HNO3 and 0.5 M NaOH respectively and were characterized by XRF, XRD, BET, SEM and FTIR techniques. The effects of processing parameters, such as initial 4-NP concentration, temperature, pH, contact time and adsorbent dosage on the adsorption process were investigated. The results obtained showed that Jatropha curcas activated carbon exhibited higher performance than activated kaolinitic clay for the removal of 4-nitrophenol from aqueous solution. Langmuir, Freundlich, Temkin and Dubinin-Radushkevich models were used to describe the adsorption isotherms. The adsorption data were best fitted with Freundlich model. The experimental data of the two adsorbate-adsorbent systems fitted very well with the pseudo-second order kinetic model with r2 values of 0.999 respectively. Adsorption thermodynamic parameters were also estimated. The results revealed that the adsorption of 4-nitrophenol onto both adsorbents were exothermic processes and spontaneous for Jatropha curcas activated carbon but non spontaneous for activated kaolinitic clay.

  19. Kinetics and thermodynamics of sorption of 4-nitrophenol on activated kaolinitic clay and jatropha curcas activated carbon from aqueous solution

    International Nuclear Information System (INIS)

    Azeez, S.O.; Adekola, F.A.

    2016-01-01

    Adsorption behaviour of 4-nitrophenol (4-NP) on activated kaolinitic clay and Jatropha curcas activated carbon was investigated. The kaolinitic clay and Jatropha curcas were activated with 1 M HNO/sub 3/ and 0.5 M NaOH respectively and were characterized by XRF, XRD, BET, SEM and FTIR techniques. The effects of processing parameters, such as initial 4-NP concentration, temperature, pH, contact time and adsorbent dosage on the adsorption process were investigated. The results obtained showed that Jatropha curcas activated carbon exhibited higher performance than activated kaolinitic clay for the removal of 4-nitrophenol from aqueous solution. Langmuir, Freundlich, Temkin and Dubinin-Radushkevich models were used to describe the adsorption isotherms. The adsorption data were best fitted with Freundlich model. The experimental data of the two adsorbate-adsorbent systems fitted very well with the pseudosecond order kinetic model with r2 values of 0.999 respectively. Adsorption thermodynamic parameters were also estimated. The results revealed that the adsorption of 4-nitrophenol onto both adsorbents were exothermic processes and spontaneous for Jatropha curcas activated carbon but non spontaneous for activated kaolinitic clay. (author)

  20. Effective adsorption and collection of cesium from aqueous solution using graphene oxide grown on porous alumina

    Science.gov (United States)

    Entani, Shiro; Honda, Mitsunori; Shimoyama, Iwao; Li, Songtian; Naramoto, Hiroshi; Yaita, Tsuyoshi; Sakai, Seiji

    2018-04-01

    Graphene oxide (GO) with a large surface area was synthesized by the direct growth of GO on porous alumina using chemical vapor deposition to study the Cs adsorption mechanism in aqueous solutions. Electronic structure analysis employing in situ near-edge X-ray absorption fine structure spectroscopy and X-ray photoelectron spectroscopy measurements clarifies the Cs atoms bond via oxygen functional groups on GO in the aqueous solution. The Cs adsorption capacity was found to be as high as 650-850 mg g-1, which indicates that the GO/porous alumina acts as an effective adsorbent with high adsorption efficiency for radioactive nuclides in aqueous solutions.

  1. Theoretical calculations of the thermodynamic stability of ionic substitutions in hydroxyapatite under an aqueous solution environment

    International Nuclear Information System (INIS)

    Matsunaga, Katsuyuki; Murata, Hidenobu; Shitara, Kazuki

    2010-01-01

    Defect formation energies in materials generally depend on chemical potentials determined by a chemical equilibrium condition. In particular, an aqueous solution environment is important for biomaterials such as hydroxyapatite studied here. Therefore, a methodology to obtain ionic chemical potentials under chemical equilibrium between solid and aqueous solution was introduced, and was applied to substitutional divalent cations formed via ion exchange with Ca 2+ in hydroxyapatite. The calculated ranking of the stability of substitutional cations in HAp was in good agreement with the experimentally observed trend. The present theoretical approach would be useful to explore the thermodynamic stability of defects in materials subjected to an aqueous solution environment.

  2. Cane molasses and NaOH teated bagacillo diets for lambs | Chicco ...

    African Journals Online (AJOL)

    Cane molasses and NaOH teated bagacillo diets for lambs. C.F. Chicco, G Garcia, C Fernandez, C.R. Prays. Abstract. The eftect of alkali-treated bag acillo in diets varying in proportion of bagacillo and mollasses was studied in lambs. The bagacillo was treated with a concentration solution of NaOH in a horizontald rum-type ...

  3. Stability of Medium-Bridged Twisted Amides in Aqueous Solutions

    Science.gov (United States)

    Szostak, Michal; Yao, Lei; Aubé, Jeffrey

    2012-01-01

    “Twisted” amides containing non-standard dihedral angles are typically hypersensitive to hydrolysis, a feature that has stringently limited their utility in water. We have synthesized a series of bridged lactams that contain a twisted amide linkage but which exhibit enhanced stability in aqueous environments. Many of these compounds were extracted unchanged from aqueous mixtures ranging from the strongly basic to the strongly acidic. NMR experiments showed that tricyclic lactams undergo reversible hydrolysis at extreme pH ranges, but that a number of compounds in this structure class are indefinitely stable under physiologically relevant pH conditions; one bicyclic example was additionally water-soluble. We examined the effect of structure on the reversibility of amide bond hydrolysis, which we attributed to the transannular nature of the amino acid analogs. These data suggest that medium-bridged lactams of these types should provide useful platforms for studying the behavior of twisted amides in aqueous systems. PMID:19178141

  4. Biosorption of Fe (II) and Cd (II) ions from aqueous solution using a ...

    African Journals Online (AJOL)

    ADOWIE PERE

    Biosorption of Fe (II) and Cd (II) ions from aqueous solution using a low cost ... human activities in the environment poses a lot of risk ... ion exchange or reverse osmosis, electrochemical treatment ..... is the adsorption coefficient, n indicates the.

  5. Quantitative Method for the Detection of Triethyl Phosphate in Aqueous Solutions

    National Research Council Canada - National Science Library

    Bagalawis, Rosa

    2003-01-01

    ...) at the parts per million level in aqueous solution. TEP was used as a chemical agent simulant to evaluate the penetration characteristics of clothing, gloves, boots and items of personal equipment...

  6. Study of colloidal properties of natural and Al-pillared smectite and removal of copper ions from an aqueous solution.

    Science.gov (United States)

    Sartor, Lucas Resmini; de Azevedo, Antonio Carlos; Andrade, Gabriel Ramatis Pugliese

    2015-01-01

    In this study, an Al-pillared smectite was synthesized and changes in its colloidal properties were investigated. The pillaring solution was prepared by mixing 0.4 mol L(-1) NaOH and 0.2 mol L(-1) AlCl3.6H2O solutions. Intercalated clays were heated to obtain the pillared clay, and X-ray diffractometry (XRD), X-ray fluorescence (XRF), Fourier transform infrared (FTIR) spectroscopy and N2 sorption/desorption isotherms analysis were done to characterize the changes in clay properties. Moreover, adsorption experiments were carried out in order to evaluate the capacity of the pillared clays to remove Cu2+ from an aqueous solution and to characterize the interaction between adsorbent and adsorbate. The results indicate that the natural clay has a basal spacing of 1.26 nm, whereas the pillared clays reached 1.78 nm (500°C) and 1.80 nm (350°C) after calcination. XRF analysis revealed an increase in the Al3+ in the pillared clay as compared to the natural clay. The surface area and pore volume (micro and mesoporous) were higher for the pillared clays. Experimental data from the adsorption experiment were fit to Langmuir and Freundlich and Temkin adsorption models, and the former one was the best fit (highest r2 value) for all the clays and lower standard deviation (Δg%) for the natural clay. On the other hand, the Temkin model exhibited Δg% value lower for the pillared clays. Thermodynamics parameters demonstrate that the Cu2+ adsorption process is spontaneous for all the clays, but with higher values for the pillared materials. In addition, application of the Dubinin-Radushkevich model revealed that the bond between the metal and the clay are weak, characterizing a physisorption.

  7. On mechanism of chlorophos radiation-chemical decomposition in aqueous solutions

    International Nuclear Information System (INIS)

    Danilin, D.I.; Shubin, V.N.

    1992-01-01

    Quantitative indices of chlorophos decomposition in a aqueous solution and in solutions with a number of additions are studied. Chlorine ions and substances containing the carbonyl group are found among the products of gamma-irradiation of low-concentration chlorophos solutions. The data supporting the running of radiation destructive reactions of reduction nature rather than oxidation type, are presented

  8. Adsorption of Remazol Black 5 from aqueous solution by the templated crosslinked-chitosans

    International Nuclear Information System (INIS)

    Chen, Arh-Hwang; Huang, Yao-Yi

    2010-01-01

    The templated crosslinked-chitosan microparticles prepared using the imprinting method with the Remazol Black5 (RB5) dye as a template, epichlorohydrin (ECH) as a crosslinker, and sodium hydroxide (NaOH) solution used for the microparticle formation showed the highest adsorption capacity for the RB5 dye compared with those that used other methods with or without a template, three crosslinkers, and two microparticle formations. The results showed that the adsorption of the RB5 dye on the microparticles was affected by the microparticle size, the initial dye concentration, the initial pH value, as well as the temperature. Both kinetics and thermodynamic parameters of the adsorption process were estimated. These data indicated an exothermic spontaneous adsorption process that kinetically followed the second-order adsorption process. Equilibrium experiments fitted well the Langmuir isotherm model, and the maximum monolayer adsorption capacity for the RB5 dye was 2941 mg/g. The competition study showed that the adsorption of the RB5 dye on the microparticles in the mixture solution was much less affected by the existence of the 3R dye than the other way around. Furthermore, the microparticles could be regenerated through the desorption of the dye in pH 10.0 of NaOH solution and could be reused to adsorb the dye again.

  9. Stabilizers of edaravone aqueous solution and their action mechanisms. 2. Glutathione

    OpenAIRE

    Tanaka, Masahiko; Motomiya, Satsuki; Fujisawa, Akio; Yamamoto, Yorihiro

    2017-01-01

    Edaravone (3-methyl-1-phenyl-2-pyrazolin-5-one) has garnered attention since its approval for amyotrophic lateral sclerosis in Japan (2015) and the United States (2017). Edaravone is administered intravenously, and as such, is distributed in the form of an aqueous solution. However, aqueous solutions of edaravone are very unstable because they present as edaravone anions, which become edaravone radicals when the anion donates an electron to free radicals including oxygen. In this study, gluta...

  10. Stabilizers of edaravone aqueous solution and their action mechanisms. 1. Sodium bisulfite

    OpenAIRE

    Tanaka, Masahiko; Sugimura, Natsuhiko; Fujisawa, Akio; Yamamoto, Yorihiro

    2017-01-01

    Edaravone (3-methyl-1-phenyl-2-pyrazolin-5-one) has been used as a free radical scavenging drug for the treatment of acute ischemic stroke in Japan since 2001. Edaravone is given to patients intravenously; therefore, it is distributed in the form of an aqueous solution. However, aqueous solutions of edaravone are very unstable because it is present as edaravone anion, which is capable of transferring an electron to free radicals including oxygen, and becomes edaravone radical. We observed the...

  11. Separation of Co2+ present in aqueous solution on calcium carbonate

    International Nuclear Information System (INIS)

    Garcia A, E.; Granados C, F.

    2008-01-01

    The CaCO 3 was synthesized by precipitation method and characterized using SEM, EDS, TGA and IR. It was studied the adsorption behavior of Co 2+ present in aqueous solution on the synthesized material by experiments batch type at room temperature. Was found that removal of cobalt ions was greater than 40% indicating that this material can be used to remove Co 2+ present in aqueous solution. (Author)

  12. Electrocoagulation-Adsorption to Remove Anionic and Cationic Dyes from Aqueous Solution by PV-Energy

    OpenAIRE

    Castañeda-Díaz, J.; Pavón-Silva, T.; Gutiérrez-Segura, E.; Colín-Cruz, A.

    2017-01-01

    The cationic dye malachite green (MG) and the anionic dye Remazol yellow (RY) were removed from aqueous solutions using electrocoagulation-adsorption processes. Batch and continuous electrocoagulation procedures were performed and compared. Carbonaceous materials obtained from industrial sewage sludge and commercial activated carbons were used to adsorb dyes from aqueous solutions in column systems with a 96–98% removal efficiency. The continuous electrocoagulation-adsorption system was more ...

  13. Theoretical approach to the destruction or sterilization of drugs in aqueous solution

    International Nuclear Information System (INIS)

    Slegers, Catherine; Tilquin, Bernard

    2005-01-01

    Two novel applications in the radiation processing of aqueous solutions of drugs are the sterilization of injectable drugs and the decontamination of hospital wastewaters by ionizing radiation. The parameters influencing the destruction of the drug in aqueous solutions are studied with a computer simulation program. This theoretical approach has revealed that the dose rate is the most important parameter that can be easily varied in order to optimize the destruction or the protection of the drug

  14. Electronic structure tautomerism, and mechanism of H-D exchange in imidazole aqueous solutions

    International Nuclear Information System (INIS)

    Borisov, Yu.A.; Vorob'eva, N.P.; Abronin, I.A.; Kolomiets, A.F.

    1988-01-01

    The imidazole electronic structure in a gaseous phase is studied taking into account the influence of solvation effects in aqueous solutions. Possible mechanisms of tautomeric transformations and H-D exchange reactions with water molecules are discussed. Using the quantum chemistry methods, it is shown that the intramolecular mechanism of imidazole isomerization in the gaseous phase and the aqueous solution is unprofitable, and the intermolecular mechanism can proceed through the stage of protonated and carbene form formation

  15. Study of the physicochemical properties of the interface between titanium dioxide and various aqueous solutions

    International Nuclear Information System (INIS)

    Mazilier, C.

    1988-01-01

    The aim of this work is the study of ion exchange capacity of titanium dioxide in view of high temperature water purification and radioactive effluent processing because of its resistance to heat and radiations. Titanium dioxide is obtained by alkaline hydrolysis of an aqueous solution of Ti (IV) and is characterized by analytical physical chemistry methods. Interface between Ti0 2 and simple aqueous solutions (electrolytes) is more particularly studied by potentiometry [fr

  16. Supercooling of aqueous dimethylsulfoxide solution at normal and high pressures: Evidence for the coexistence of phase-separated aqueous dimethylsulfoxide solutions of different water structures

    Science.gov (United States)

    Kanno, H.; Kajiwara, K.; Miyata, K.

    2010-05-01

    Supercooling behavior of aqueous dimethylsulfoxide (DMSO) solution was investigated as a function of DMSO concentration and at high pressures. A linear relationship was observed for TH (homogeneous ice nucleation temperature) and Tm (melting temperature) for the supercooling of aqueous DMSO solution at normal pressure. Analysis of the DTA (differential thermal analysis) traces for homogeneous ice crystallization in the bottom region of the TH curve for a DMSO solution of R =20 (R: moles of water/moles of DMSO) at high pressures supported the contention that the second critical point (SCP) of liquid water should exist at Pc2=˜200 MPa and at Tc2pressure of SCP, Tc2: temperature of SCP). The presence of two TH peaks for DMSO solutions (R =15, 12, and 10) suggests that phase separation occurs in aqueous DMSO solution (R ≤15) at high pressures and low temperatures (pressure dependence of the two TH curves for DMSO solutions of R =10 and 12 indicates that the two phase-separated components in the DMSO solution of R =10 have different liquid water structures [LDL-like and HDL-like structures (LDL: low-density liquid water, HDL: high-density liquid water)] in the pressure range of 120-230 MPa.

  17. Characterization of trehalose aqueous solutions by neutron spin echo

    Energy Technology Data Exchange (ETDEWEB)

    Branca, C.; Faraone, A.; Magazu' , S.; Maisano, G.; Mangione, A. [Dipartimento di Fisica and INFM, Universita di Messina, PO Box 55, 98166 Messina (Italy); Pappas, C.; Triolo, A. [Hahn-Meitner-Institut, BENSC (NI), Glienicker Strasse, 14109 Berlin (Germany)

    2002-07-01

    The present work reports neutron spin-echo (NSE) results on aqueous mixtures of trehalose, a naturally occurring disaccharide of glucose, which shows an extraordinary bioprotective effectiveness against dehydration and freezing. The aim of the work is to furnish new results on the dynamics of the trehalose/water system on the nano- and picosecond scales. (orig.)

  18. Characterization of trehalose aqueous solutions by neutron spin echo

    CERN Document Server

    Branca, C; Magazù, S; Maisano, G; Mangione, A; Pappas, C; Triolo, A

    2002-01-01

    The present work reports neutron spin-echo (NSE) results on aqueous mixtures of trehalose, a naturally occurring disaccharide of glucose, which shows an extraordinary bioprotective effectiveness against dehydration and freezing. The aim of the work is to furnish new results on the dynamics of the trehalose/water system on the nano- and picosecond scales. (orig.)

  19. Determination of 90Sr from aqueous solutions using SPE extraction

    International Nuclear Information System (INIS)

    Dulanska, S.; Rajec, P.; Matel, L.

    2008-01-01

    Solid Phase Extraction (SPE) is widely used technique for the isolation and concentration of analytes from liquid samples to achieve increased sensitivity in the analytical process. Three commercial sorbents produced by three different manufacturers were tested. 3M Empore TM Strontium Rad Disks, Sr resin and AnaLig Sr-01 were used to efficiently isolate strontium from aqueous samples. (authors)

  20. [Enhancement effect of double-beam laser processed aqueous solution on ICP emission spectrum].

    Science.gov (United States)

    Chen, Jin-zhong; Xu, Li-jing; Su, Hong-xin; Li, Xu; Wang, Shu-fang

    2015-01-01

    In order to change the physical properties of aqueous solution and improve the radiation intensity of the ICP emission spectrum, the effects of different laser power density and irradiation time on the surface tension and viscosity of aqueous solution were investigated by using near infrared laser at 976 nm and CO2 laser at 10. 6 µm to irradiate aqueous solution orthogonally, then the enhancement of ICP spectral intensity with processed solution was discussed. The results showed that the surface tension and viscosity of aqueous solution reduced by 42. 13% and 14. 03% compared with the untreated, and the atomization efficiency increased by 51.26% at the laser power density 0. 265 7 W . cm-2 of 976 nm and 0. 206 9 W . cm-2 of CO2 laser with 40 min irradiation time. With the optimized aqueous solution introduced into the ICP source, the spectral line intensity of sample elements As, Cd, Cr, Hg and Pb was enhanced by 46.29%, 94. 65%, 30. 76%, 33.07% and 94. 58% compared to the untreated aqueous solution, while the signal-to-background ratio increased by 43. 84%, 85. 35%, 28. 71%, 34. 37% and 90. 91%, respectively. Plasma temperature and electron density also increased by 5. 94% and 1. 18% respectively. It is obvious that the method of double-beam laser orthogonal irradiation on solution can reduce the surface tension and viscosity of aqueous solution significantly, and raise the radiationintensity of ICP source, and will provide a better condition for detecting the trace heavy metal elements in water samples.

  1. Interaction between bacteriophage and pyrophyllite clay in aqueous solution

    Science.gov (United States)

    Park, Jeong-Ann; Kim, Jae-Hyun; Kang, Jin-Kyu; Son, Jeong-Woo; Yi, In-Geol; Kim, Song-Bae

    2014-05-01

    Viral contamination results in a degradation in drinking water quality and a threat to public health. Toprovide safe drinking water, water treatment alternatives using various adsorbents and filter media such as activated carbon, bituminous coal, quartz sand and clay have been considered. Pyrophyllite is a 2:1 clay mineral having dioctahedral layer structure with octahedrally coordinated Al ion sheets between two sheets of SiO4 tetrahedra. It is a hydrous aluminosilicate clay with the chemical composition AlSi2O5(OH). Pyrophyllite has recently been investigated as a potential low-cost and environmental friendly adsorbent for removing various contaminants. The aim of this study was to investigate the removal of the bacteriophage MS2 from aqueous solution using pyrophyllite. Batch experiments were conducted to examine the MS2 sorption to pyrophyllite. The influence of fluoride, a groundwater contaminant, on the removal of MS2 was also observed. Batch results demonstrated that pyrophyllite was effective in MS2 removal. The percent removal increased from 5.26% to 99.99% (= 4.0 log removal) as the pyrophyllite concentrations increased from 0.2 to 20 g/L. More than 99% of MS2 could be removed with a pyrophyllite concentration of ≥ 4 g/L. The sorption of MS2 to pyrophyllite was rapid. Within 15 min, approximately 99.98% (= 3.7 log removal) of MS2 was attained. More than 4.0 log removal was achieved after 180 min. The experimental data were analyzed with the pseudo first-order and pseudo second-order kinetic models. The correlation coefficient showed that pseudo second-order model was better than pseudo first-order model at describing the kinetic data. The amount of MS2 removed at equilibrium was determined to be 1.43 × 108 pfu/g from the pseudo second-order model. The experimental data were also analyzed with the Freundlich and Langmuir isotherm models. The correlation coefficients showed that the Langmuir model was more suitable than the Freundlich model for MS2

  2. Aqueous solutions of acidic ionic liquids for enhanced stability of polyoxometalate-carbon supercapacitor electrodes

    Science.gov (United States)

    Hu, Chenchen; Zhao, Enbo; Nitta, Naoki; Magasinski, Alexandre; Berdichevsky, Gene; Yushin, Gleb

    2016-09-01

    Nanocomposites based on polyoxometalates (POMs) nanoconfined in microporous carbons have been synthesized and used as electrodes for supercapacitors. The addition of the pseudocapacitance from highly reversible redox reaction of POMs to the electric double-layer capacitance of carbon lead to an increase in specific capacitance of ∼90% at 1 mV s-1. However, high solubility of POM in traditional aqueous electrolytes leads to rapid capacity fading. Here we demonstrate that the use of aqueous solutions of protic ionic liquids (P-IL) as electrolyte instead of aqueous sulfuric acid solutions offers an opportunity to significantly improve POM cycling stability. Virtually no degradation in capacitance was observed in POM-based positive electrode after 10,000 cycles in an asymmetric capacitor with P-IL aqueous electrolyte. As such, POM-based carbon composites may now present a viable solution for enhancing energy density of electrical double layer capacitors (EDLC) based on pure carbon electrodes.

  3. Aqueous-Containing Precursor Solutions for Efficient Perovskite Solar Cells.

    Science.gov (United States)

    Liu, Dianyi; Traverse, Christopher J; Chen, Pei; Elinski, Mark; Yang, Chenchen; Wang, Lili; Young, Margaret; Lunt, Richard R

    2018-01-01

    Perovskite semiconductors have emerged as competitive candidates for photovoltaic applications due to their exceptional optoelectronic properties. However, the impact of moisture instability on perovskite films is still a key challenge for perovskite devices. While substantial effort is focused on preventing moisture interaction during the fabrication process, it is demonstrated that low moisture sensitivity, enhanced crystallization, and high performance can actually be achieved by exposure to high water content (up to 25 vol%) during fabrication with an aqueous-containing perovskite precursor. The perovskite solar cells fabricated by this aqueous method show good reproducibility of high efficiency with average power conversion efficiency (PCE) of 18.7% and champion PCE of 20.1% under solar simulation. This study shows that water-perovskite interactions do not necessarily negatively impact the perovskite film preparation process even at the highest efficiencies and that exposure to high contents of water can actually enable humidity tolerance during fabrication in air.

  4. The synthesis of nucleotide in the aqueous solution induced by low energy ions

    International Nuclear Information System (INIS)

    Shi Huaibin; Shao Chunlin; Wang Xiangqin; Yu Zengliang

    2000-08-01

    A new apparatus was designed to induce reactions in aqueous solution by introducing low energy ions into the aqueous solution, this apparatus overcome the defaults of the old ones which demanded vacuum and made it possible to study the action among solutions, it also expanded the ion implantation biology. The role of low energy ions was introduced into the study of the origin of life, primitive earth conditions were imitated to study prior-life synthesis of nucleotide by introducing low energy ions into aqueous solution, low energy N + was implanted into adenine supersaturation solution including D-ribose and NH 4 H 2 PO 4 , it was confirmed that 5'-AMP was gained by HPLC analysis of the products. In comparison with other methods in this field, this one is simpler and nearer to the primitive earth conditions, thus it provided a new try for the studying of the origin of life

  5. The kinetics of dye formation by pulse radiolysis of pararosaniline cyanide in aqueous or organic solution

    International Nuclear Information System (INIS)

    McLaughlin, W.L.; Holcman, J.; Sehested, K.; Kosanic, M.M.

    1979-11-01

    The radiation-induced conversion of the leucocyanide of pararosaniline dye to the highly colored salt-isomer of the dye in acidic aqueous solution (wavelength of maximum absorption lambda sub(max)=540 nm) or polar organic solution (lambda sub(max)=550 nm), takes place in two separate processes. The first is very fast (within 3 s -1 to 10 6 s -1 , as the acidity or concentration of an oxidizing agent increases. In oxygen-free acidic aqueous or organic solutions (argon saturated) there is an unstable transient species (lambdasub(max)=380 nm). When using O 2 or N 2 O-saturated aqueous or organic solution, there is no intermediate absorption band at 380 nm, but the slow process of dye formation at 540 or 550 nm is still sequential to the initial fast process having somewhat faster kinetics than in Ar-saturated solution. (author)

  6. Recoil halogen reactions in liquid and frozen aqueous solutions of biomolecules

    International Nuclear Information System (INIS)

    Arsenault, L.J.; Blotcky, A.J.; Firouzbakht, M.L.; Rack, E.P.; Nebraska Univ., Omaha

    1982-01-01

    Reactions of recoil 38 Cl, 80 Br and 128 I have been studied in crystalline systems of 5-halouracil, 5-halo-2'-deoxyuridine and 5-halouridine as well as liquid and frozen aqueous solutions of these halogenated biomolecules. In all systems expect crystalline 5-iuodouracil the major product was the radio-labelled halide ion. There was no evidence for other halogen inorganic species. The major labelled organic product was the parent molecule. A recoil atom tracer technique was developed to acquire site information of the biomolecule solutes in the liquid and frozen aqueous systems. For all liquid and frozen aqueous systems, the halogenated biomolecules tended to aggregate. For liquid systems, the tendency for aggregation diminished as the solute concentration approached zero, where the probable state of the solute approached a monomolecular dispersion. Unlike the liquid state, the frozen ice lattice demonstated a ''caging effect'' for the solute aggregates which resulted in constant product yields over the whole concentration range. (orig.)

  7. Removal of heavy metals from aqueous solution by using mango ...

    African Journals Online (AJOL)

    user

    2011-03-14

    Mar 14, 2011 ... exchange, reverse osmosis and solvent extraction (Rich and Cherry, 1987). ... the solution chemistry of the metals, the activity of the functional groups in the .... and Zn2+ from synthetic solutions in single and binary metal solutions. ... coefficient of determination are 0.9449 and 0.9643 for. Langmiur and ...

  8. NDMA Formation during Chlorination and Chloramination of Aqueous Diuron Solutions

    OpenAIRE

    Young, Thomas M

    2008-01-01

    Formation of the potent carcinogen N-nitrosodimethylamine (NDMA) during chlorine disinfection of water containing secondary amines is now generally acknowledged. The phenylurea herbicide diuron is one of the most widely used herbicides in California, has been frequently detected in California’s water sources with a transient nature of appearance, and has a structure that suggests it might be an NDMA precursor. This study sought to quantify the potential for NDMA formation from aqueous diuron ...

  9. Treatment of infectious skin defects or ulcers with electrolyzed strong acid aqueous solution.

    Science.gov (United States)

    Sekiya, S; Ohmori, K; Harii, K

    1997-01-01

    A chronic ulcer with an infection such as methicillin-resistant Staphylococcus aureus is hard to heal. Plastic and reconstructive surgeons often encounter such chronic ulcers that are resistant to surgical or various conservative treatments. We applied conservative treatment using an electrolyzed strong acid aqueous solution and obtained satisfactory results. The lesion was washed with the solution or soaked in a bowl of the solution for approximately 20 min twice a day. Fresh electrolyzed strong acid aqueous solution is unstable and should be stored in a cool, dark site in a sealed bottle. It should be used within a week after it has been produced. Here we report on 15 cases of infectious ulcers that were treated by electrolyzed strong acid aqueous solution. Of these cases, 7 patients were healed, 3 were granulated, and in 5, infection subsided. In most cases the lesion became less reddish and less edematous. Discharge or foul odor from the lesion was decreased. Electrolyzed strong acid aqueous solution was especially effective for treating a chronic refractory ulcer combined with diabetes melitus or peripheral circulatory insufficiency. This clinically applied therapy of electrolyzed strong acid aqueous solution was found to be effective so that this new therapeutic technique for ulcer treatment can now be conveniently utilized.

  10. Cd(II) removal from aqueous solution by adsorption on α-ketoglutaric acid-modified magnetic chitosan

    International Nuclear Information System (INIS)

    Yang, Guide; Tang, Lin; Lei, Xiaoxia; Zeng, Guangming; Cai, Ye; Wei, Xue; Zhou, Yaoyu; Li, Sisi; Fang, Yan; Zhang, Yi

    2014-01-01

    The present study developed an α-ketoglutaric acid-modified magnetic chitosan (α-KA-Fe 3 O 4 /CS) for highly efficient adsorption of Cd(II) from aqueous solution. Several techniques, including transmission electron microscopy (TEM), Fourier transform infrared (FTIR) and vibrating sample magnetometer (VSM), were applied to characterize the adsorbent. Batch tests were conducted to investigate the Cd(II) adsorption performance of α-KA-Fe 3 O 4 /CS. The maximum adsorption efficiency of Cd(II) appeared at pH 6.0 with the value of 93%. The adsorption amount was large and even reached 201.2 mg/g with the initial Cd(II) concentration of 1000 mg/L. The adsorption equilibrium was reached within 30 min and commendably described by pseudo-second-order model, and Langmuir model fitted the adsorption isotherm better. Furthermore, thermodynamic parameters, free energy (ΔG), enthalpy (ΔH) and entropy (ΔS) of Cd(II) adsorption were also calculated and showed that the overall adsorption process was endothermic and spontaneous in nature because of positive ΔH values and negative ΔG values, respectively. Moreover, the Cd(II)-loaded α-KA-Fe 3 O 4 /CS could be regenerated by 0.02 mol/L NaOH solution, and the cadmium removal capacity could still be kept around 89% in the sixth cycle. All the results indicated that α-KA-Fe 3 O 4 /CS was a promising adsorbent in environment pollution cleanup.

  11. Removal of Cr(VI) from aqueous solution by flocculant with the capacity of reduction and chelation

    International Nuclear Information System (INIS)

    Wang, Gang; Chang, Qing; Han, Xiaoting; Zhang, Mingyue

    2013-01-01

    Highlights: ► We report a novel flocculant with the properties of reduction and chelation for Cr. ► The removal of Cr(VI) by the flocculant depends highly on pH value. ► Some coexisting ions inhibit Cr (VI) removal, but promote total Cr removal. ► Cr and turbidity can be removed simultaneously in the treated wastewater. ► The interaction mechanism is investigated by FTIR and SEM. -- Abstract: A novel agent polyethyleneimine-sodium xanthogenate (PEX) with the multifunction of reduction, chelation, flocculation and precipitation was synthesized by using polyethyleneimine (PEI), carbon disulfide (CS 2 ), and sodium hydroxide (NaOH). The effects of different important parameters, such as pH value, initial Cr(VI) concentration, coexisting ions and turbidity etc., on the removal of chromium from aqueous solution by PEX were investigated in flocculation experiments. The experiments results demonstrated that PEX could efficiently remove Cr(VI) and total Cr (Cr(VI) + Cr(III)) in strongly acidic media. It was proved that the presence of coexisting ions (Na + , Ca 2+ , F − , Cl − , and SO 4 2− ) in the solution had a little influence on the removal of chromium. Furthermore, it was conformed that Cr(VI) ions and turbidity could be simultaneously removed when water samples contained both Cr(VI) ions and turbidity. Finally, the mechanism of interaction between chromium and PEX was further confirmed by Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The results reveal that dithiocarboxylic acid groups on PEX macromolecule play a major role in Cr(VI) reduction and Cr(III) chelation, and the flocs formation is attributed to the interparticle bridging mechanism of PEX

  12. X-ray Studies of Regenerated Cellulose Fibers Wet Spun from Cotton Linter Pulp in NaOH/Thiourea Aqueous Solutions

    Energy Technology Data Exchange (ETDEWEB)

    Chen,X.; Burger, C.; Fang, D.; Ruan, D.; Zhang, L.; Hsiao, B.; Chu, B.

    2006-01-01

    Regenerated cellulose fibers were fabricated by dissolution of cotton linter pulp in NaOH (9.5 wt%) and thiourea (4.5 wt%) aqueous solution followed by wet-spinning and multi-roller drawing. The multi-roller drawing process involved three stages: coagulation (I), coagulation (II) and post-treatment (III). The crystalline structure and morphology of regenerated cellulose fiber was investigated by synchrotron wide-angle X-ray diffraction (WAXD) and small-angle X-ray scattering (SAXS) techniques. Results indicated that only the cellulose II crystal structure was found in regenerated cellulose fibers, proving that the cellulose crystals were completely transformed from cellulose I to II structure during spinning from NaOH/thiourea aqueous solution. The crystallinity, orientation and crystal size at each stage were determined from the WAXD analysis. Drawing of cellulose fibers in the coagulation (II) bath (H{sub 2}SO{sub 4}/H{sub 2}O) was found to generate higher orientation and crystallinity than drawing in the post-treatment (III). Although the post-treatment process also increased crystal orientation, it led to a decrease in crystallinity with notable reduction in the anisotropic fraction. Compared with commercial rayon fibers fabricated by the viscose process, the regenerated cellulose fibers exhibited higher crystallinity but lower crystal orientation. SAXS results revealed a clear scattering maximum along the meridian direction in all regenerated cellulose fibers, indicating the formation of lamellar structure during spinning.

  13. Fabrication of Lead-Free Bi0.5Na0.5TiO3 Thin Films by Aqueous Chemical Solution Deposition

    Directory of Open Access Journals (Sweden)

    Mads Christensen

    2017-02-01

    Full Text Available Piezoelectric ceramics are widely used in actuator applications, and currently the vast majority of these devices are based on Pb ( Zr , Ti O 3 , which constitutes environmental and health hazards due to the toxicity of lead. One of the most promising lead-free material systems for actuators is based on Bi 0 . 5 Na 0 . 5 TiO 3 (BNT, and here we report on successful fabrication of BNT thin films by aqueous chemical solution deposition. The precursor solution used in the synthesis is based on bismuth citrate stabilized by ethanolamine, NaOH , and a Ti-citrate prepared from titanium tetraisopropoxide and citric acid. BNT thin films were deposited on SrTiO 3 and platinized silicon substrates by spin-coating, and the films were pyrolized and annealed by rapid thermal processing. The BNT perovskite phase formed after calcination at 500 °C in air. The deposited thin films were single phase according to X-ray diffraction, and the microstructures of the films shown by electron microscopy were homogeneous and dense. Decomposition of the gel was thoroughly investigated, and the conditions resulting in phase pure materials were identified. This new aqueous deposition route is low cost, robust, and suitable for development of BNT based thin film for actuator applications.

  14. Surface micro-dissolve method of imparting self-cleaning property to cotton fabrics in NaOH/urea aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Fan, Tao; Hu, Ruimin; Zhao, Zhenyun [College of Textile & Garment, Southwest University, 400716, Chongqing (China); Liu, Yiping [College of Textile & Garment, Southwest University, 400716, Chongqing (China); Chongqing Engineering Research Center of Biomaterial Fiber and Modern Textile, 400716, Chongqing (China); Lu, Ming, E-mail: lumingswu@163.com [College of Textile & Garment, Southwest University, 400716, Chongqing (China); Chongqing Engineering Research Center of Biomaterial Fiber and Modern Textile, 400716, Chongqing (China)

    2017-04-01

    Highlights: • A novel micro-dissolved process was carried out to embedding commercial titanium dioxide nanoparticles into cotton fabric with NaOH/urea aqueous solution. • X-ray diffraction pattern of modified fabrics shown that the cellulose structure of modified fabrics had not changed. • Modified cotton fabrics demonstrated favourable photocatalytic self-cleaning performance while tensile strength and whiteness of treated fabrics also expressed an increasement slightly. - Abstract: A simple and economical micro-dissolved process of embedding titanium dioxide (TiO{sub 2}) nanoparticles into surface zone of cotton fabrics was developed. TiO{sub 2} was coated on cotton fabrics in 7% wt NaOH/12% wt urea aqueous solution at low temperature. Photocatalytic efficiency of cotton fabrics treated with TiO{sub 2} nanoparticles was studied upon measuring the photocatalytic decoloration of Rhodamine B (RhB) under ultraviolet irradiation. Self-cleaning property of cotton fabric coated with TiO{sub 2} was evaluated with color depth of samples (K/S value). The treated fabrics were characterized using scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), Fourier transform infrared spectroscopy (FITR), tensile strength, stiffness and whiteness. The results indicated, TiO{sub 2} nanoparticles could be embedded on the surface layer of cotton fabrics throuth surface micro-dissolve method. Treated cotton fabrics possessed distinct photocatalytic efficiency and self-cleaning properties. Tensile strength and whiteness of modified cotton fabrics appeared moderately increasement.

  15. Comparative analysis of the effect of pretreating aspen wood with aqueous and aqueous-organic solutions of sulfuric and nitric acid on its reactivity during enzymatic hydrolysis

    DEFF Research Database (Denmark)

    Dotsenko, Gleb; Osipov, D. O.; Zorov, I. N.

    2016-01-01

    The effect of aspen wood pretreatment methods with the use of both aqueous solutions of sulfuric and nitric acids and aqueous-organic solutions (ethanol, butanol) of sulfuric acid (organosolv) on the limiting degree of conversion of this type of raw material into simple sugars during enzymatic...

  16. Cow bones char as a green sorbent for fluorides removal from aqueous solutions: batch and fixed-bed studies.

    Science.gov (United States)

    Nigri, Elbert M; Cechinel, Maria Alice P; Mayer, Diego A; Mazur, Luciana P; Loureiro, José M; Rocha, Sônia D F; Vilar, Vítor J P

    2017-01-01

    Cow bone char was investigated as sorbent for the defluoridation of aqueous solutions. The cow bone char was characterized in terms of its morphology, chemical composition, and functional groups present on the bone char surface using different analytical techniques: SEM, EDS, N 2 -BET method, and FTIR. Batch equilibrium studies were performed for the bone chars prepared using different procedures. The highest sorption capacities for fluoride were obtained for the acid washed (q = 6.2 ± 0.5 mg/g) and Al-doped (q = 6.4 ± 0.3 mg/g) bone chars. Langmuir and Freundlich models fitted well the equilibrium sorption data. Fluoride removal rate in batch system is fast in the first 5 h, decreasing after this time until achieving equilibrium due to pore diffusion. The presence of carbonate and bicarbonate ions in the aqueous solution contributes to a decrease of the fluoride sorption capacity of the bone char by 79 and 31 %, respectively. Regeneration of the F-loaded bone char using 0.5 M NaOH solution leads to a sorption capacity for fluoride of 3.1 mg/g in the second loading cycle. Fluoride breakthrough curve obtained in a fixed-bed column presents an asymmetrical S-shaped form, with a slow approach of C/C 0  → 1.0 due to pore diffusion phenomena. Considering the guideline value for drinking water of 1.5 mg F - /L, as recommended by World Health Organization, the service cycle for fluoride removal was of 71.0 h ([F - ] feed  ∼ 9 mg/L; flow rate = 1 mL/min; m sorbent  = 12.6 g). A mass transfer model considering the pore diffusion was able to satisfactorily describe the experimental data obtained in batch and continuous systems.

  17. The immiscible aqueous solutions of alkyl phosphates. Study for the purpose of uranium extraction from phosphoric acid solutions

    International Nuclear Information System (INIS)

    Mauborgne, Bernard

    1979-01-01

    Systems of immiscible aqueous solutions composed by a phase rich in mineral salt and by another phase almost totally containing an organic salt, have been studied for years, with quaternary ammonium salts with an organic cation. The objective of this research is to study systems symmetric to the previous ones, i.e. with organic anions such as alkyl phosphates, and then to try to understand mechanisms of extraction of metals in these environments. Based on properties of immiscible aqueous solutions, an original three-phase process of liquid-liquid extraction has been developed, and is used to separate uranium in phosphoric acids with better performance than the existing industrial processes [fr

  18. Measuring the density and viscosity of H2S-loaded aqueous methyldiethanolamine solution

    International Nuclear Information System (INIS)

    Shokouhi, Mohammad; Ahmadi, Reza

    2016-01-01

    Highlights: • Measurement solubility of H 2 S in 46.78 mass% MDEA aqueous solutions. • Measurement density of H 2 S loaded of MDEA aqueous solution. • Measurement viscosity of H 2 S loaded of MDEA aqueous solution. • Correlation of the density and viscosity of H 2 S loaded of MDEA aqueous solution using modified setchenow equation. - Abstract: The density and viscosity of H 2 S-loaded aqueous 46.78 mass% methyldiethanolamine solution were experimentally measured accompanied with the solubility of H 2 S at temperatures (313.15, 328.15 and 343.15) K, pressures from vapor pressure of fresh solution up to 1.0 MPa and loadings up to 1.00 mol of H 2 S per 1 mol of amine. All experimental trials have been carried out using the new setup developed in our laboratory. It was observed that both density and viscosity of mixtures decrease by increasing temperature and density increase by increasing acid gas solubility (loading) by about 4.7%, whereas viscosity has a complicated behavior with H 2 S solubility. Viscosity decreases by increasing acid gas solubility (loading) at 313.15 K by about 20.6% and at 328.15 K by about 15.0%, but it is comparable at 343.15 K in terms of H 2 S solubility. Finally, the experimental density and viscosity data correlated using Modified Setchenow equation.

  19. Oscillometric and conductometric analysis of aqueous and organic dosimeter solutions

    DEFF Research Database (Denmark)

    Kovacs, A.; Slezsak, I.; McLaughlin, W.L.

    1995-01-01

    Conductometric and oscillometric evaluation methods have earlier been developed to determine absorbed dose in the ethanol-monochlorobenzene dosimeter solution. Recent investigations on the same solution as well as on alanine solutions included the study of the possible use of different type ''con...... of the applicable concentration of the alanine solute and the dose (1 to 50 kGy) and dose-rate range using both electron (2.6 mu s at 13 mu A to 4 mu s at 1.0 A pulse length and beam current) and gamma radiation (0.13 to 30 kGy h(-1))....

  20. Pulse radiolysis of pyridinecarboxylic acids in aqueous solution

    DEFF Research Database (Denmark)

    Solar, S.; Getoff, N.; Sehested, K.

    1991-01-01

    The reactivity of OH, e(aq)- and H radicals towards aqueous carboxypyridines: picolinic acid (2-pyridinecarboxylic acid), PA; isonicotinic acid (4-pyridinecarboxylic acid), i-NA; 2,6-pyridinedicarboxylic acid, 2,6-PDCA; and 3,5-pyridinedicarboxylic acid, 3,5-PDCA was investigated in the pH-range 1...... radical are: 20% for PA, 75% for i-NA, 60% for 2,6-PDCA and 25% for 3,5-PDCA (a yield of 50% has been found earlier for nicotinic acid, NA)....

  1. A thermodynamic study of glucose and related oligomers in aqueous solution: Vapor pressures and enthalpies of mixing

    DEFF Research Database (Denmark)

    Cooke, S.A.; Jonsdottir, Svava Osk; Westh, Peter

    2002-01-01

    Vapor pressures above aqueous solutions of glucose and maltose at both 298.06 K and 317.99 K and vapor pressures above aqueous solutions of cellobiose, maltotriose, maltotetraose, and maltopentaose at 317.99 K have been measured. The excess enthalpies have been recorded for all of the above-menti...... in aqueous solution. This so-called transference principle is found to be of interest in furthering the discussion concerning the applicability of lattice-based models for solution theory....

  2. Relation Between the Adsorbed Quantity and the Immersion Enthalpy in Catechol Aqueous Solutions on Activated Carbons

    OpenAIRE

    Moreno-Piraj?n, Juan Carlos; Blanco, Diego; Giraldo, Liliana

    2011-01-01

    An activated carbon, CarbochemTM—PS230, was modified by chemical and thermal treatment in flow of H2, in order to evaluate the influence of the activated carbon chemical characteristics in the adsorption of the catechol. The catechol adsorption in aqueous solution was studied along with the effect of the pH solution in the adsorption process of modified activated carbons and the variation of immersion enthalpy of activated carbons in the aqueous solutions of catechol. The interaction solid-so...

  3. An introduction to radiation induced degradation of biological molecules in aqueous solutions

    International Nuclear Information System (INIS)

    Lal, Manohar

    1991-01-01

    Radiation chemistry of aqueous systems is the chemistry of H, OH, e aq - , H 3 O + and H 2 O * formed when a solute in aqueous solutions is exposed to ionising radiation. The pulse radiolysis technique has helped in the production, the detection and understanding of the reactions of primary species with solutes. A great deal of data on radiation biochemical studies e.g. degradation of DNA, its constituents and their protection, radiation protection and sensitisation, generation of superoxide ion and their reactions has already been reported but a great deal still needs to be done for the understanding of radiation biology. (author). 12 refs

  4. Sorption Potentials of Waste Tyre for Some Heavy Metals (Pb Cd in Aqueous Solution

    Directory of Open Access Journals (Sweden)

    Austin Kanayo ASIAGWU

    2009-07-01

    Full Text Available An investigation into the adsorption potential of activated and inactivated waste tyre powders for some heavy metals (Pb2+ and Cd2+ in their aqueous solution has been studied. The result indicated that inactivated waste tyre is a good non-conventional adsorbent for the removal of Cd from aqueous solution. A total of 93.3% of Cadmium contents was removed. The inactivated waste type proved a good adsorbent for the removal of Pb2+ 5g of 500mm activated tyre removed over 86.66% of Pb2+ from solution.

  5. Aqueous solutions of proline and NaCl studied by differential scanning calorimetry at subzero temperatures

    DEFF Research Database (Denmark)

    Rasmussen, Peter Have; Jørgensen, Bo; Nielsen, Jette

    1997-01-01

    The hydration properties of proline are studied by differential scanning calorimetry (DSC) in aqueous solutions during freezing to -60 degrees C and subsequent heating to +20 degrees C. The concentration of proline in the freeze concentrated solution was estimated to approximately 50 wt% (w/w) in...... plants and insects living under water stress conditions is discussed. (C) 1997 Elsevier Science B.V....

  6. KINETICS OF THE HYDROXYPROPYLATION OF POTATO STARCH IN AQUEOUS-SOLUTION

    NARCIS (Netherlands)

    LAMMERS, G; STAMHUIS, EJ; BEENACKERS, AACM

    Kinetic results are presented for the hydroxypropylation of Potato starch with methyloxirane in aqueous solution. Reaction temperatures were varied from 303 to 362 K. Sodium hydroxide was used as a catalyst. The overall conversion rate of methyloxirane in alkaline starch solution is determined by

  7. Adsorption of Pb(II) ions from aqueous solution using lignin from ...

    African Journals Online (AJOL)

    The adsorption of lead(II) ions from aqueous solution onto alkali lignin extracted from Hagenia abyssinica was investigated by electrochemical methods. The effect of solution pH, lignin dosage and contact time were investigated at room temperature in a batch system. Adsorption equilibrium was approached within 80 min.

  8. Biosorption of nickel (II) ions from aqueous solutions by tapioca peel ...

    African Journals Online (AJOL)

    Tapioca peel, waste from native tapioca starch industry in Thailand, was used for the biosorption of nickel from aqueous solution. The experimental parameter focuses on the influence of contact time, solution pH, initial concentration and temperature using batch experiments. The results indicated that the biosorption ...

  9. Chemical systems in aqueous solutions for using in the holographic ionizing radiation

    International Nuclear Information System (INIS)

    Nicolau-Rebigan, S.

    1979-01-01

    Some types of chemical systems in aqueous solutions for utilization as active media in holographic ionizing radiation dosimeter are presented. One discussed some advantages of the holographic dosimeter comparatively with another existing types. It is outlined the advantages of using aqueousss solutions as active media in holographic dosimeter. (author)

  10. Ultrafast X-ray absorption study of longitudinal-transverse phonon coupling in electrolyte aqueous solution

    DEFF Research Database (Denmark)

    Jiao, Yishuo; Adams, Bernhard W.; Dohn, Asmus Ougaard

    2017-01-01

    Ultrafast X-ray absorption spectroscopy is applied to study the conversion of longitudinal to transverse phonons in aqueous solution. Permanganate solutes serve as X-ray probe molecules that permit the measurement of the conversion of 13.5 GHz, longitudinal phonons to 27 GHz, transverse phonons...

  11. Volumetric and viscometric studies of some drugs in aqueous solutions at different temperatures

    International Nuclear Information System (INIS)

    Dhondge, Sudhakar S.; Zodape, Sangesh P.; Parwate, Dilip V.

    2012-01-01

    Highlights: ► Study of aqueous solutions of biologically important compounds has been reported. ► MH is used for treating type II diabetes, RH is in treatment of peptic ulcer and TH is used to treat severe pain. ► All the compounds act as structure makers by volumetric studies. ► MH and RH act as weak structure breakers and TH acts as a weak structure maker by viscometric studies. - Abstract: Density and viscosity measurements are reported for aqueous solutions of the drugs like Metformin hydrochloride (MH), Ranitidine hydrochloride (RH) and Tramadol hydrochloride (TH) at different temperatures T = (288.15, 298.15, and 308.15) K within the concentration range (0 to 0.15) mol · kg −1 . The density and viscosity data are used to obtain apparent molar volume of solute (φ V ) and relative viscosity (η r ) of aqueous solutions at different temperatures. The limiting apparent molar volume of solute (φ V 0 ), limiting apparent molar expansivity (φ E 0 ), thermal expansion coefficient (α ∗ ), hydration number (n h ), Jones–Dole equation viscosity A and B coefficients, experimental slope (S V ) at different temperatures, and temperature coefficient of Bi.e.(dB/dT) at T = 298.15 K were also obtained. The results obtained have been interpreted in terms of solute–solvent and solute–solute interactions and structure making/breaking ability of solute in the aqueous solution.

  12. The use of Algerian clay materials for the sorption of heavy metals from aqueous solutions

    International Nuclear Information System (INIS)

    Dib, S.; Boufatit, M.

    2009-01-01

    The present study investigates the adsorption of Pb 2 +, Cu 2 + and Ni 2 + onto Algerian bentonite clay from aqueous solutions at different initial concentration of metal ions, amount of clay, solution pH, shaking time at room temperature. The uptake of Pb 2 +, Cu 2 +, Cu 2 + and Ni 2 + was dependent on increasing pH of the medium. (Author)

  13. Rapid synthesis of CdSe nanocrystals in aqueous solution at room ...

    Indian Academy of Sciences (India)

    Administrator

    Water-soluble thioglycolic acid-capped CdSe nanocrystals (NCs) were prepared in aqueous solu- tion at room temperature. We investigated the ... NCs dispersed in buffer solution (pH = 4⋅0). FTIR spectra were recorded on a ... the theory of acid-base equilibrium, the initial pH value of original solution determines the ...

  14. Comparison of cytotoxicity in vitro and irritation in vivo for aqueous and oily solutions of surfactants.

    Science.gov (United States)

    Czajkowska-Kośnik, Anna; Wolska, Eliza; Chorążewicz, Juliusz; Sznitowska, Małgorzata

    2015-01-01

    The in vivo model on rabbit eyes and the in vitro cytotoxicity on fibroblasts were used to compare irritation effect of aqueous and oily (Miglyol 812) solutions of surfactants. Tween 20, Tween 80 and Cremophor EL were tested in different concentrations (0.1, 1 or 5%) and the in vitro test demonstrated that surfactants in oil are less cytotoxic than in aqueous solutions. In the in vivo study, the aqueous solutions of surfactants were characterized as non-irritant while small changes in conjunctiva were observed after application the oily solutions of surfactants and the preparations were classified as slightly irritant, however this effect was similar when Miglyol was applied alone. In conclusion, it is reported that the MTT assay does not correlate well with the Draize scores.

  15. Solubility and viscosity for CO_2 capture process using MEA promoted DEAE aqueous solution

    International Nuclear Information System (INIS)

    Fu, Dong; Wang, LeMeng; Zhang, Pan; Mi, ChenLu

    2016-01-01

    Highlights: • Solubility of CO_2 in MEA promoted DEAE aqueous solution was measured. • Mass fraction and temperature dependences of solubility were illustrated. • Viscosities of carbonated MEA–DEAE solutions were measured and calculated. • Temperature, mass fraction and CO_2 loading dependences of viscosity were illustrated. - Abstract: The saturated solubility of CO_2 in monoethanolamine (MEA) promoted 2-diethylaminoethanol (DEAE) aqueous solution was investigated at temperatures ranging from (303.2 to 323.2) K. The mass fraction and temperature dependences of the saturated solubility and CO_2 loading are illustrated. The viscosities of both CO_2-unloaded and CO_2-loaded DEAE–MEA aqueous solutions were measured and then calculated by using the Weiland equation. The effects of temperature, mass fraction and CO_2 loading on viscosities are demonstrated.

  16. Effect of temperature on the behavior of surface properties of alcohols in aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Romero, Carmen M. [Facultad de Ciencias, Universidad Nacional de Colombia, Bogota (Colombia)], E-mail: cmromeroi@unal.edu.co; Jimenez, Eulogio [Facultade de Ciencias, Universidade da Coruna (Spain); Suarez, Felipe [Facultad de Ciencias, Universidad Nacional de Colombia, Bogota (Colombia)

    2009-04-15

    The influence of temperature on the behavior of surface properties of aqueous solutions has often been used to obtain information about solute structural effects on water. In this work, we present experimental results for surface tension of aqueous solutions of n-pentanol, n-hexanol, n-heptanol, and n-octanol at T = (283.15, 288.15, 293.15, 298.15, 303.15, and 308.15) K at several concentrations. The results were used to evaluate the limiting experimental slopes of surface tension with respect to mole fraction and the hydrophobicity constant of the Connors model at each temperature. The thermodynamic behavior of aqueous alcohol solutions is discussed in terms of the effect of the hydrocarbon chain on water structure. The temperature dependence of the limiting slopes of surface tension with respect to mole fraction, as well as the hydrophobicity constant derived from surface measurements, is interpreted in terms of alcohol hydration.

  17. Effect of temperature on the behavior of surface properties of alcohols in aqueous solution

    International Nuclear Information System (INIS)

    Romero, Carmen M.; Jimenez, Eulogio; Suarez, Felipe

    2009-01-01

    The influence of temperature on the behavior of surface properties of aqueous solutions has often been used to obtain information about solute structural effects on water. In this work, we present experimental results for surface tension of aqueous solutions of n-pentanol, n-hexanol, n-heptanol, and n-octanol at T = (283.15, 288.15, 293.15, 298.15, 303.15, and 308.15) K at several concentrations. The results were used to evaluate the limiting experimental slopes of surface tension with respect to mole fraction and the hydrophobicity constant of the Connors model at each temperature. The thermodynamic behavior of aqueous alcohol solutions is discussed in terms of the effect of the hydrocarbon chain on water structure. The temperature dependence of the limiting slopes of surface tension with respect to mole fraction, as well as the hydrophobicity constant derived from surface measurements, is interpreted in terms of alcohol hydration

  18. The kinetics of anodic dissolution of rhenium in aqueous electrolyte solutions

    International Nuclear Information System (INIS)

    Atanasyants, A.G.; Kornienko, V.A.

    1986-01-01

    The kinetics of anodic rhenium dissolution was investigated by means of potentiodynamic and potentiostatic polarization curves recorded at temperature from 293 to 333 K in different media (NaOH, KOH, NaCl, NaBr, HCl, H 2 SO 4 ) using the rotating disc technique. It is shown that the kinetics of anodic rhenium dissolution and effective activation energy depend not only on the composition and pH value of the solutions but also on the structure of the dissolving rhenium surface. The investigation of the anodic behaviour of the rhenium monocrystal revealed the existence of anisotropy of the monocrystal electrochemical properties. The experimental results point to an important role of adsorption processes in anodic rhenium dissolution. Rhenium dissolution proceeds with formation of intermediate surface adsorption complexes between the metal and the components of the solution

  19. Reaction paths and equilibrium end-points in solid-solution aqueous-solution systems

    Science.gov (United States)

    Glynn, P.D.; Reardon, E.J.; Plummer, Niel; Busenberg, E.

    1990-01-01

    Equations are presented describing equilibrium in binary solid-solution aqueous-solution (SSAS) systems after a dissolution, precipitation, or recrystallization process, as a function of the composition and relative proportion of the initial phases. Equilibrium phase diagrams incorporating the concept of stoichiometric saturation are used to interpret possible reaction paths and to demonstrate relations between stoichiometric saturation, primary saturation, and thermodynamic equilibrium states. The concept of stoichiometric saturation is found useful in interpreting and putting limits on dissolution pathways, but there currently is no basis for possible application of this concept to the prediction and/ or understanding of precipitation processes. Previously published dissolution experiments for (Ba, Sr)SO4 and (Sr, Ca)C??O3orth. solids are interpreted using equilibrium phase diagrams. These studies show that stoichiometric saturation can control, or at least influence, initial congruent dissolution pathways. The results for (Sr, Ca)CO3orth. solids reveal that stoichiometric saturation can also control the initial stages of incongruent dissolution, despite the intrinsic instability of some of the initial solids. In contrast, recrystallisation experiments in the highly soluble KCl-KBr-H2O system demonstrate equilibrium. The excess free energy of mixing calculated for K(Cl, Br) solids is closely modeled by the relation GE = ??KBr??KClRT[a0 + a1(2??KBr-1)], where a0 is 1.40 ?? 0.02, a1, is -0.08 ?? 0.03 at 25??C, and ??KBr and ??KCl are the mole fractions of KBr and KCl in the solids. The phase diagram constructed using this fit reveals an alyotropic maximum located at ??KBr = 0.676 and at a total solubility product, ???? = [K+]([Cl-] + [Br-]) = 15.35. ?? 1990.

  20. Status of determining transuranic nuclides speciation in aqueous solution with laser spectrometry

    International Nuclear Information System (INIS)

    Wang Bo; Liu Dejun; Yao Jun; Chen Xi; Long Haoqi; Zeng Jishu; Su Xiguang; Fan Xianhua

    2007-01-01

    The knowledge about speciation of transuranic nuclides in aqueous solution is a basis for understanding the chemical and migration behavior of transuranic nuclides in aqueous solution. The speciation of transuranic nuclides with trace concentration is complicated in near neutral aqueous solutions, including change of oxidation state, complexation and colloid generation, etc. The concentrations of transuranium in near neutral aqueous solution usually below the sensitivity range of method such as conventional absorption spectroscopy. The radioactive analysis method has a very low detection limits for radionuclides, however, it wouldn' t allow the direct measurement of the transuranic species. In contrast with these methods, laser spectroscopy is an ideal method with high sensitivity, and non-contact and non-destructive for determining the speciation of transuranic nuclides. This paper summarizes the status and application of LIPAS (Laser-induced Photoacoustic Spectrometry), LIBD (Laser-induced Breakdown Detection) and TRLFS (Time-resolved Laser Fluorescence Spectrometry) to determine the speciation of transuranic nuclides with trace concentration in aqueous solutions. (authors)

  1. Thermodynamic behavior of erythritol in aqueous solutions and in gelatine gels and its quantification

    International Nuclear Information System (INIS)

    Tyapkova, Oxana; Bader-Mittermaier, Stephanie; Schweiggert-Weisz, Ute

    2013-01-01

    Highlights: • Differential scanning calorimetry as a method to determine erythritol crystallization. • Determination of crystallization using solution enthalpy. • Erythritol crystallization influenced by area of air–water-interfaces. • DSC method is applicable for both aqueous solutions and gels. • Adaption of DSC method to other, more complex food matrices is possible. - Abstract: As crystallization of erythritol can cause a sandy mouth-feel in sugar-free products, strategies to avoid crystallization or adaption of food formulation should be elucidated. However, until now erythritol crystallization was only quantified in aqueous solutions, but not in model food systems. Differential scanning calorimetry (DSC) is a simple method for the quantification of phase transition in various systems. However, no methods for the quantification of crystallization from aqueous systems based on DSC have been published until now. In the present study DSC was found to be suitable for the quantification of crystallization using supersaturated aqueous solutions of erythritol and erythritol containing gelatine gels for the first time. The developed method was validated by comparing the crystallization values determined by gravimetric measurement of erythritol crystals and the values obtained by DSC. No significant differences (p < 0.05) have been obtained between the results of the two methods if an appropriate design of measurements was applied. Additionally, the method was adapted to gelatine gels to elucidate the transferability to model food systems. Hence, the method is suitable for quantification of the amount of erythritol crystals present in aqueous solutions and gels, respectively

  2. Process for plutonium rextraction in aqueous solution from an organic solvent, especially for uranium plutonium partition

    International Nuclear Information System (INIS)

    Germain, M.; Gillet, B.; Pasquiou, J.Y.

    1989-01-01

    The organic solvent containing plutonium is contacted with an aqueous solution of a uranous salt, for instance uranous nitrate, and a hydroxylamine salt, for instance the nitrate. In these conditions uranous nitrate is a reducing agent of Pu III and hydroxylamine nitrate stabilizes Pu III and U IV in the aqueous phase. Performances are similar to these of the U IV-hydrazine nitrate without interference of hydrazine nitrate degradation products [fr

  3. Photoproduction of hydroxyl radicals in aqueous solution with algae under high-pressure mercury lamp.

    Science.gov (United States)

    Liu, Xianli; Wu, Feng; Deng, Nansheng

    2004-01-01

    Photoproduction of hydroxyl radicals (*OH) could be induced in aqueous solution with algae (Nitzschia hantzschiana, etc.) and (or not) Fe3+ under high-pressure mercury lamp with an exposure time of 4 h. *OH was determined by HPLC using benzene as a probe. The photoproduction of *OH increased with increasing algae concentration. Fe3+ could enhance the photoproduction of *OH in aqueous solution with algae. The results showed that the photoproduction of *OH in algal solution with Fe3+ was greater than that in algal solution without Fe3+. The light intensity and pH affected the photoproduction of *OH in aqueous solution with algae with/without Fe3+. The photoproduction of *OH in aqueous solution with algae and Fe3+ under 250 W was greater than that under 125 W HPML. The photoproduction of *OH in algal solution (pH ranged from 4.0 to 7.0) with (or not) Fe3+ at pH 4 was the greatest.

  4. Fluoride removal from aqueous solution by pumice: case study on ...

    African Journals Online (AJOL)

    EJIRO

    conditions, the fluoride removal efficiency from Kuhbonan water by 2.8 mg/L fluoride was 74.64%. Eventually ... industrial wastewater containing fluoride is a key ..... solution using silica ceramic: Adsorption kinetics and equilibrium studies.

  5. Enthalpic characteristics of interactions occurring between an ascorbic acid and some saccharides in aqueous solutions

    International Nuclear Information System (INIS)

    Terekhova, Irina V.; Kulikov, Oleg V.; Titova, Elena S.

    2004-01-01

    The enthalpies of solution of mono- and disaccharides were measured in water and aqueous ascorbic acid solutions at 298.15 K using a calorimeter of solution. Enthalpies of transfer of saccharides from water to aqueous ascorbic acid solutions were derived, and enthalpic coefficients of pair interaction h xy were calculated according to MacMillan-Mayer theory. Interactions of ascorbic acid with D-fructose and sucrose are energetically favorable and characterized by negative h xy coefficients while h xy for the interactions occurring between ascorbic acid and α-D glucose, D-galactose and maltose are positive. The obtained results are interpreted in terms of the influence of structure and solvation of solutes on the thermodynamic parameters of their interaction in solutions

  6. The use of erbium fiber laser relaxation frequency for sensing refractive index and solute concentration of aqueous solutions

    International Nuclear Information System (INIS)

    Arellano-Sotelo, H; Barmenkov, Yu O; Kir'yanov, A V

    2008-01-01

    We report a novel-principle fiber-laser intra-cavity sensor for measuring refractive index and solute concentration of aqueous solutions. The sensor operation is based on a variation of the laser oscillation relaxation frequency (the measured parameter), sensitive to the intra-cavity loss change. The sensor capacity is demonstrated on the example of measurements of sugar concentration in water. A modeling of the sensor operation is presented, allowing its performance optimization

  7. Estimation of stability constants of metal monoacidocomplexes in aqueous solutions (1:2) of electrolytes

    International Nuclear Information System (INIS)

    Ryazanov, M.A.

    1992-01-01

    On the basis of the concept of the model of isoactive solutions it is shown that osmosis pressure of aqueous solutions (1:2) of electrolytes is well described by the Van-der-Vaals model for ideal associated gas. Stabilisty constants were calculated using osmosis mole parts of interacting particles as a concentrational scale. Stability constants in the scale of osmosis mole parts are equal to thermodynamic contstants, rated for an infinitely diluted solution

  8. On the attenuation of X-rays and gamma-rays for aqueous solutions of salts

    CERN Document Server

    Teli, M T

    1998-01-01

    Disparities in the linear attenuation coefficients of X-rays and gamma rays for aqueous solutions of soluble salts arising from the nonequality of volume of the solution with the sum of volumes of its components are analysed and the mixture rule is reformulated. The disparities are illustrated for NaCl solution for concentrations c=0 to 1 gm/cm sup 3 which indicates that the mixture rule of Teli et al. works well within generally acceptable limits.

  9. Adsorption of Procion Blue MX-R dye from aqueous solutions by lignin chemically modified with aluminium and manganese

    International Nuclear Information System (INIS)

    Adebayo, Matthew A.; Prola, Lizie D.T.; Lima, Eder C.; Puchana-Rosero, M.J.; Cataluña, Renato; Saucier, Caroline; Umpierres, Cibele S.; Vaghetti, Julio C.P.; Silva, Leandro G. da; Ruggiero, Reinaldo

    2014-01-01

    Graphical abstract: - Highlights: • Complexes of carboxy-methylated lignin with Al and Mn were used as adsorbents. • The optimum adsorption conditions were achieved at pH 2 and 298 K. • Maximum adsorption capacities are 73.52 mg g −1 (CML-Al) and 55.16 mg g −1 (CML-Mn). • CML-Al could remove ca. 95.83% of dye-contaminated industrial effluents. • CML-Al and CML-Mn are effective for treatment of simulated dye-house effluents. - Abstract: A macromolecule, CML, was obtained by purifying and carboxy-methylating the lignin generated from acid hydrolysis of sugarcane bagasse during bioethanol production from biomass. The CMLs complexed with Al 3+ (CML-Al) and Mn 2+ (CML-Mn) were utilised for the removal of a textile dye, Procion Blue MX-R (PB), from aqueous solutions. CML-Al and CML-Mn were characterised using Fourier transform infrared spectroscopy (FTIR), scanning differential calorimetry (SDC), scanning electron microscopy (SEM) and pH PZC . The established optimum pH and contact time were 2.0 and 5 h, respectively. The kinetic and equilibrium data fit into the general order kinetic model and Liu isotherm model, respectively. The CML-Al and CML-Mn have respective values of maximum adsorption capacities of 73.52 and 55.16 mg g −1 at 298 K. Four cycles of adsorption/desorption experiments were performed attaining regenerations of up to 98.33% (CML-Al) and 98.08% (CML-Mn) from dye-loaded adsorbents, using 50% acetone + 50% of 0.05 mol L −1 NaOH. The CML-Al removed ca. 93.97% while CML-Mn removed ca. 75.91% of simulated dye house effluents

  10. Adsorption of Procion Blue MX-R dye from aqueous solutions by lignin chemically modified with aluminium and manganese

    Energy Technology Data Exchange (ETDEWEB)

    Adebayo, Matthew A. [Institute of Chemistry, Federal University of Rio Grande do Sul (UFRGS), Av. Bento Gonçalves 9500, Postal Box 15003, 91501-970 Porto Alegre, RS (Brazil); Department of Chemical Sciences, Ajayi Crowther University, PMB 1066 Oyo, Oyo State (Nigeria); Prola, Lizie D.T. [Institute of Chemistry, Federal University of Rio Grande do Sul (UFRGS), Av. Bento Gonçalves 9500, Postal Box 15003, 91501-970 Porto Alegre, RS (Brazil); Lima, Eder C., E-mail: eder.lima@ufrgs.br [Institute of Chemistry, Federal University of Rio Grande do Sul (UFRGS), Av. Bento Gonçalves 9500, Postal Box 15003, 91501-970 Porto Alegre, RS (Brazil); Puchana-Rosero, M.J.; Cataluña, Renato; Saucier, Caroline; Umpierres, Cibele S.; Vaghetti, Julio C.P. [Institute of Chemistry, Federal University of Rio Grande do Sul (UFRGS), Av. Bento Gonçalves 9500, Postal Box 15003, 91501-970 Porto Alegre, RS (Brazil); Silva, Leandro G. da; Ruggiero, Reinaldo [Institute of Chemistry, Federal University of Uberlândia (UFU), AV. João Naves de Ávila 2121 block 1D—Campus Santa Mônica, 38400-902 Uberlândia, MG (Brazil)

    2014-03-01

    Graphical abstract: - Highlights: • Complexes of carboxy-methylated lignin with Al and Mn were used as adsorbents. • The optimum adsorption conditions were achieved at pH 2 and 298 K. • Maximum adsorption capacities are 73.52 mg g{sup −1} (CML-Al) and 55.16 mg g{sup −1} (CML-Mn). • CML-Al could remove ca. 95.83% of dye-contaminated industrial effluents. • CML-Al and CML-Mn are effective for treatment of simulated dye-house effluents. - Abstract: A macromolecule, CML, was obtained by purifying and carboxy-methylating the lignin generated from acid hydrolysis of sugarcane bagasse during bioethanol production from biomass. The CMLs complexed with Al{sup 3+} (CML-Al) and Mn{sup 2+} (CML-Mn) were utilised for the removal of a textile dye, Procion Blue MX-R (PB), from aqueous solutions. CML-Al and CML-Mn were characterised using Fourier transform infrared spectroscopy (FTIR), scanning differential calorimetry (SDC), scanning electron microscopy (SEM) and pH{sub PZC}. The established optimum pH and contact time were 2.0 and 5 h, respectively. The kinetic and equilibrium data fit into the general order kinetic model and Liu isotherm model, respectively. The CML-Al and CML-Mn have respective values of maximum adsorption capacities of 73.52 and 55.16 mg g{sup −1} at 298 K. Four cycles of adsorption/desorption experiments were performed attaining regenerations of up to 98.33% (CML-Al) and 98.08% (CML-Mn) from dye-loaded adsorbents, using 50% acetone + 50% of 0.05 mol L{sup −1} NaOH. The CML-Al removed ca. 93.97% while CML-Mn removed ca. 75.91% of simulated dye house effluents.

  11. Adsorption of Polycyclic Aromatic Hydrocarbons (PAHS from Aqueous Solutions on Different Sorbents

    Directory of Open Access Journals (Sweden)

    Smol Marzena

    2014-12-01

    Full Text Available This paper presents the results of the possibility and effectiveness of PAHs removal from a model aqueous solution, during the sorption on the selected sorbents. Six PAHs (naphthalene, acenaphthylene, acenaphthene, fluorene, phenanthrene, anthracene listed by EPA for the analysis in the environmental samples were determined. Model aqueous solution was prepared with RESTEK 610 mix PAHs standard. After the sorption process, decrease in the concentration of individual hydrocarbons was observed. The removal percentage was dependent on the type of sorbent (quartz sand, mineral sorbent, activated carbon. The highest efficiency (98.1% was observed for activated carbon.. The results shows that the sorption processes can be used in aqueous solutions treatment procedures.

  12. Sorption of ochratoxin A from aqueous solutions using β-cyclodextrin-polyurethane polymer.

    Science.gov (United States)

    Appell, Michael; Jackson, Michael A

    2012-02-01

    The ability of a cyclodextrin-polyurethane polymer to remove ochratoxin A from aqueous solutions was examined by batch rebinding assays. The results from the aqueous binding studies were fit to two parameter models to gain insight into the interaction of ochratoxin A with the nanosponge material. The ochratoxin A sorption data fit well to the heterogeneous Freundlich isotherm model. The polymer was less effective at binding ochratoxin A in high pH buffer (9.5) under conditions where ochratoxin A exists predominantly in the dianionic state. Batch rebinding assays in red wine indicate the polymer is able to remove significant levels of ochratoxin A from spiked solutions between 1-10 μg·L(-1). These results suggest cyclodextrin nanosponge materials are suitable to reduce levels of ochratoxin A from spiked aqueous solutions and red wine samples.

  13. Fluoresence quenching of riboflavin in aqueous solution by methionin and cystein

    International Nuclear Information System (INIS)

    Droessler, P.; Holzer, W.; Penzkofer, A.; Hegemann, P.

    2003-01-01

    The fluorescence quantum distributions, fluorescence quantum yields, and fluorescence lifetimes of riboflavin in methanol, DMSO, water, and aqueous solutions of the sulphur atom containing amino acids methionin and cystein have been determined. In methanol, DMSO, and water (pH=4-8) only dynamic fluorescence reduction due to intersystem crossing and internal conversion is observed. In aqueous methionin solutions of pH=5.25-9 a pH independent static and dynamic fluorescence quenching occurs probably due to riboflavin anion-methionin cation pair formation. In aqueous cystein solutions (pH range from 4.15 to 9) the fluorescence quenching increases with rising pH due to cystein thiolate formation. The cystein thiol form present at low pH does not react with neutral riboflavin. Cystein thiolate present at high pH seems to react with neutral riboflavin causing riboflavin deprotonation (anion formation) by cystein thiolate reduction to the cystein thiol form

  14. Application of Activated Carbon for Removal of Arsenic Ions from Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    R. Ansari

    2007-01-01

    Full Text Available The activated carbon (AC was used for removal of As(III and As(V ions from aqueous solutions. Sorption experiments were conducted using both batch and column systems. The effect of some important parameters on sorption of these by AC was studied. It was found that among the different factors affecting sorption capacity and efficiency in removal of arsenic from aqueous solutions, the effect of pH and the oxidation state were the most prominent. The optimum pH values for removal of As(III and As(V from aqueous solutions using AC was found 12 and 3 respectively. Impregnation of AC with sulphur contain organic dyes, it is possible to improve As(III uptake considerably.

  15. Density Fluctuation in Aqueous Solutions and Molecular Origin of Salting-Out Effect for CO2

    International Nuclear Information System (INIS)

    Ho, Tuan Anh; Ilgen, Anastasia

    2017-01-01

    Using molecular dynamics simulation, we studied the density fluctuations and cavity formation probabilities in aqueous solutions and their effect on the hydration of CO 2 . With increasing salt concentration, we report an increased probability of observing a larger than the average number of species in the probe volume. Our energetic analyses indicate that the van der Waals and electrostatic interactions between CO 2 and aqueous solutions become more favorable with increasing salt concentration, favoring the solubility of CO 2 (salting in). However, due to the decreasing number of cavities forming when salt concentration is increased, the solubility of CO 2 decreases. The formation of cavities was found to be the primary control on the dissolution of gas, and is responsible for the observed CO 2 salting-out effect. Finally, our results provide the fundamental understanding of the density fluctuation in aqueous solutions and the molecular origin of the salting-out effect for real gas.

  16. Physicochemical analysis of cryocrystallization processes of aqueous solutions of yttrium, barium, copper nitrates and their mixtures

    International Nuclear Information System (INIS)

    Kulakov, A.B.; Mozhaev, A.P.; Tesker, A.M.; Churagulov, B.R.

    1992-01-01

    Products of fast hardening of aqueous solutions of different concentration of yttrium, barium copper nitrates and their mixtures including mixture of three nitrates with molar ratio equal to 1:2:3 used for synthesis of YBa 2 Cu 3 O 7-x HTSC by cryochemical technique, in liquid nitrogen, are studied using low-temperature, differential thermal and X-ray phase analyses. Aqueous solutions of barium, copper, yttrium nitrates are shown to belong to three different classes which differ in behaviour at fast cooling and subsequent slow heating. Cryogranulate at YBa 2 Cu 2 O 7-x synthesis using cryochemical technique represents mixture of X-ray amorphous Ba(NO 3 ) 2 , crystalline Cu(NO 3 ) 2 ·6H 2 O and ice, as well as, supercooled aqueous solution of yttrium and copper nitrates

  17. Removal of radium from aqueous solutions using adsorbent produced from coconut coir pith

    International Nuclear Information System (INIS)

    Zalina Laili; Muhamat Omar; Mohd Zaidi Ibrahim; Esther Phillip; Mohd Abdul Wahab Yusof; Hassan, A.

    2008-08-01

    A study was conducted to evaluate the potential use of the coconut coir pith as an adsorbent for the removal of radium from aqueous solutions. Experiments to establish adsorptions as a function of pH and contact time were carried out. The results showed that radium adsorption are dependent upon pH and contact time of coconut coir pith with aqueous solutions. 70-80% of radium were adsorbed in the neutral to alkaline pH range. The amount of radium adsorbed also increased with contact time, reaching an optimum after 250 min. Thus, it can be concluded that the coconut coir pith has the potential to be used as an adsorbent in radium removal from aqueous solutions. (Author)

  18. Radiolysis of aqueous solution of plutonium; Radiolyse des solutions aqueuses de plutonium

    Energy Technology Data Exchange (ETDEWEB)

    Pages nee Flon, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1960-07-01

    This study is concerned first with the effects of gamma rays on plutonium aqueous solutions at various valency states, in presence of sulfuric, perchloric, nitric and hydrochloric acids. The main feature is the reduction of Pu VI into Pu V, followed by dismutation from V to IV and VI. For sulfuric and perchloric acid solutions (0,2 N) the following process is given: radiolysis of water produces OH, H{sub 2}O{sub 2}, H and H{sub 2}. H and H{sub 2}O{sub 2} reduce Pu VI while Pu V is oxidised by OH radicals. However the reaction of hydrogen peroxide is slow and leads to an after effect. A parallel study of the action of H{sub 2}O{sub 2} has given a confirmation. Spectrophotometric measurements were carried out on disappearance of Pu VI and formation of Pu IV and it was possible to make determination of G{sub H{sub 2}}{sub O{sub 2}} = 0,8 and G{sub H} - G{sub OH} = 0,8. G{sub H{sub 2}} = 0,41 was measured by gas analysis. The calculation of G{sub {sup -}}{sub H{sub 2}}{sub O} gave 4,35. The re-oxidation of Pu V is dependant on the concentration of sulfate ions. In perchloric acid solution reduction goes on to Pu Ill. Cl{sup -} and NO{sub 3}{sup -} ions inhibit the reduction and even suppress it. The effect of alpha particles both from plutonium and from polonium is very similar to the effect of hydrogen peroxyde. Induction time were observed mainly in presence of HSO{sub 4}{sup -}, depending on the accumulation of H{sub 2}O{sub 2} and (or) of plutonium peroxide. At low acidities, Pu IV peroxide seems to lead to polymer forms. In the more simple cases (H{sub 2}SO{sub 4} and HClO{sub 4} 0,2N), the following yields were found: G (equivalent reduced) = 3.2, G{sub H{sub 2}}{sub O{sub 2}} = 1.35, G{sub H{sub 2}} = 1.6 and G{sub H} - G{sub OH} = 0.1, assuming G{sub HO{sub 2}} = 0.2; and the usual hypothesis on radiolysis of water by alpha particles. Radiation induced oxidation of Pu III into Pu IV was also observed in H{sub 2}SO{sub 4} and HNO{sub 3} aqueous solutions, and

  19. Resorcinol adsorption from aqueous solution over activated carbon

    International Nuclear Information System (INIS)

    Blanco, Diego A; Giraldo, Liliana; Moreno, Juan C

    2007-01-01

    In this paper, the adsorption behavior of Resorcinol a monohydroxylated phenol, poorly acid to 298 K, over activated carbon is analyzed by studying the solution's pH influence and the surface reduction in the adsorption process. To do this, an activated carbon of lignocellulose origin and a reduced activated carbon was used. The interaction solid solution is characterized by the analyses of adsorption in the isotherms to 298 K and pH values of 7. 00, 9.00 and 11.00 for a period of 48 hours. The capacity adsorption of activated carbons increases when the solution's pH decreases and the retained amount increases in the reduced coal to the pH of maximum adsorption.

  20. Radiolysis of Reactive AZO Dyes in Aqueous Solution

    International Nuclear Information System (INIS)

    Bagyo, Agustin NM; Winarti-Andayani; Hendig-Winarno; Ermin-Katrin; Soebianto, Yanti S

    2004-01-01

    The effects of radiation on aerated reactive dye solutions i.e Cibacron Violet, Cibacron Orange and Cibacron Yellow solutions have been studied. Parameters analysis were the change of pH after radiation, the change of absorption, degradation products and effects of pH on the radiolysis. The uv-vis absorption of solutions were observed before and after irradiation. pH variation was done from pHs 3, 5, 7, 9 and 12. Irradiation was done at doses of 0, 2, 4, 6, 8 and 10 kGy with dose rate of 5 kGy/h and was determined by a Fricke dosimeter. HPLC with UV detector was used to analyze the degradation products. Oxalic acid was the main degradation product and small amount of succinic acid was also detected. (author)

  1. Corrosion fatigue behavior of high strength brass in aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Hamada, A.S.; Kassem, M.A.; Ramadan, R.M.; El-Zeky, M.A. [Suez Canal Univ., Dept. of Metallurgy and Materials Engineering (Egypt)

    2000-07-01

    Corrosion fatigue behavior of British Standard high strength brass, CZ 127 has been studied in various environments, 3.5%NaC1 solution and 3.5%NaC1 containing 1000ppm ammonia by applying the reverse bending technique, strain-controlled cyclic, at 67 cycles/min. Characteristics of the produced alloy were studied using differential thermal analysis with applying its results in heat treating of the alloy; metallographic examinations; hardness measurements; X-ray; and electrochemical behavior of the unstressed alloy. CZ 127 was fatigued at three different conditions, solution treated, peak aged, and over aged at a fixed strain amplitude, 0.03 5. Solution treated alloy gave the best fatigue properties in all environments tested among the other materials. Results of the alloy studied were compared with that obtained of 70/30 {alpha}-brass. Fracture surface of the fatigued alloy was examined using optical microscope and scanning electron microscope equipped with EDX. (author)

  2. Corrosion fatigue behavior of high strength brass in aqueous solutions

    International Nuclear Information System (INIS)

    Hamada, A.S.; Kassem, M.A.; Ramadan, R.M.; El-Zeky, M.A.

    2000-01-01

    Corrosion fatigue behavior of British Standard high strength brass, CZ 127 has been studied in various environments, 3.5%NaC1 solution and 3.5%NaC1 containing 1000ppm ammonia by applying the reverse bending technique, strain-controlled cyclic, at 67 cycles/min. Characteristics of the produced alloy were studied using differential thermal analysis with applying its results in heat treating of the alloy; metallographic examinations; hardness measurements; X-ray; and electrochemical behavior of the unstressed alloy. CZ 127 was fatigued at three different conditions, solution treated, peak aged, and over aged at a fixed strain amplitude, 0.03 5. Solution treated alloy gave the best fatigue properties in all environments tested among the other materials. Results of the alloy studied were compared with that obtained of 70/30 α-brass. Fracture surface of the fatigued alloy was examined using optical microscope and scanning electron microscope equipped with EDX. (author)

  3. Investigation of complexing of trivalent lanthanoids in aqueous nitrate solutions

    International Nuclear Information System (INIS)

    Kopyrin, A.A.; Proyaev, V.V.; Edinakova, V.

    1985-01-01

    Complexing of trivalent lanthanoids (Ce, Eu) with nitrate-ions in concentrated solutions of lithium and sodium nitrates has been studied in a wide range of ionic forces (1.0-7.0), using the extractional, densimetric and solubility methods. Nitrate complexes registered by the extraction and solubility methods mainly are of second sphere character. During rare earth extraction from concentrated nitrate solutions in the range of nitrate-ion concentrations <= 5 mol/l second sphere neutral nitrate complexes take part in distribution, at higher values of nitrate-ion concentration formation of intrasphere monoligand complexes of lanthanoids should be taken into account

  4. Electrogenerated chemiluminescence induced by sequential hot electron and hole injection into aqueous electrolyte solution

    Energy Technology Data Exchange (ETDEWEB)

    Salminen, Kalle; Kuosmanen, Päivi; Pusa, Matti [Aalto University, Department of Chemistry, Laboratory of Analytical Chemistry, P.O. Box 16100, FI-00076 Aalto (Finland); Kulmala, Oskari [University of Helsinki, Department of Physics, P.O. Box 64, FI-00014 (Finland); Håkansson, Markus [Aalto University, Department of Chemistry, Laboratory of Analytical Chemistry, P.O. Box 16100, FI-00076 Aalto (Finland); Kulmala, Sakari, E-mail: sakari.kulmala@aalto.fi [Aalto University, Department of Chemistry, Laboratory of Analytical Chemistry, P.O. Box 16100, FI-00076 Aalto (Finland)

    2016-03-17

    Hole injection into aqueous electrolyte solution is proposed to occur when oxide-coated aluminum electrode is anodically pulse-polarized by a voltage pulse train containing sufficiently high-voltage anodic pulses. The effects of anodic pulses are studied by using an aromatic Tb(III) chelate as a probe known to produce intensive hot electron-induced electrochemiluminescence (HECL) with plain cathodic pulses and preoxidized electrodes. The presently studied system allows injection of hot electrons and holes successively into aqueous electrolyte solutions and can be utilized in detecting electrochemiluminescent labels in fully aqueous solutions, and actually, the system is suggested to be quite close to a pulse radiolysis system providing hydrated electrons and hydroxyl radicals as the primary radicals in aqueous solution without the problems and hazards of ionizing radiation. The analytical power of the present excitation waveforms are that they allow detection of electrochemiluminescent labels at very low detection limits in bioaffinity assays such as in immunoassays or DNA probe assays. The two important properties of the present waveforms are: (i) they provide in situ oxidation of the electrode surface resulting in the desired oxide film thickness and (ii) they can provide one-electron oxidants for the system by hole injection either via F- and F{sup +}-center band of the oxide or by direct hole injection to valence band of water at highly anodic pulse amplitudes. - Highlights: • Hot electrons injected into aqueous electrolyte solution. • Generation of hydrated electrons. • Hole injection into aqueous electrolyte solution. • Generation of hydroxyl radicals.

  5. Selected specific rates of reactions of transients from water in aqueous solution. Hydrated electron, supplemental data. [Reactions with transients from water, with inorganic solutes, and with solutes

    Energy Technology Data Exchange (ETDEWEB)

    Ross, A.B.

    1975-06-01

    A compilation of rates of reactions of hydrated electrons with other transients and with organic and inorganic solutes in aqueous solution appeared in NSRDS-NBS 43, and covered the literature up to early 1971. This supplement includes additional rates which have been published through July 1973.

  6. Copper complexation by tannic acid in aqueous solution

    NARCIS (Netherlands)

    Kraal, P.; Jansen, B.; Nierop, K.G.J.; Verstraten, J.M.

    2006-01-01

    The speciation of titrated copper in a dissolved tannic acid (TA) solution with an initial concentration of 4 mmol organic carbon ((OC)/l was investigated in a nine-step titration experiment (Cu/oC molar ratio = 0.0030-0.0567). We differentiated between soluble and insoluble Cu species by 0.45 mu m

  7. In Vitro Antioxidant Activity of Chitosan Aqueous Solution: Effect of ...

    African Journals Online (AJOL)

    ... (CS-TPP) and chitosan ethylenediaminetetraacetic acid (CS-EDTA) solution were determined employing various established in vitro system such as superoxide and hydroxyl radicals scavenging, metal ion chelating and reducing power. Their chemical structures were characterized by nuclear magnetic resonance (NMR) ...

  8. Preparation, assay and certification of aqueous ethanol reference solutions

    CSIR Research Space (South Africa)

    Archer, M

    2007-04-01

    Full Text Available with traceability to the SI. Ethanol solutions in the concentration range 10 mg/100 g to 20 g/100 g are prepared gravimetrically by mixing ethanol and reagent quality water. To verify the concentration of the ethanol it is oxidized to acetic acid with potassium...

  9. Spectroscopic study on the stability of morin in aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Bark, Ki Min [Dept. of Chemical Education and Research Institute of Life Science, Gyeongsang National University, Chinju (Korea, Republic of); Im, Seo Eun; Seo, Jung Ja; Park, Ok Hyun; Park, Hyoung Ryun [Dept. of Chemistry, Chonnam National University, Gwangju (Korea, Republic of); Park, Chul Ho [Dept. of Cosmetic Science, Nambu University, Gwangju (Korea, Republic of)

    2015-02-15

    Morin (3,2,4,5,7-pentahydroxyflavone) is a flavonol conjugated to a resorcinol moiety at the C-2 position, different from many other flavonoids. The UV–vis spectrum of morin in neat water reveals two major absorption bands with maxima at 265 and 387 nm. The substance is stable in acidic solution and neat water. However, its absorption maximum at 387 nm continuously shifts to longer wavelengths and new peaks appeared at wavelengths of 312 nm with increasing pH of the solution. The shape of the absorption spectrum of morin depends on the storage time at a given pH, indicating the occurrence of other successive chemical reactions. The fluorescence spectroscopic results also prove that new conjugated double bonds are formed in the deaerated basic solution at the initial state and decompose with time. This behavior indicates that morin is very unstable, and therefore its decomposition occurs by a sequence of multistep reactions in basic solution. Probable reaction pathways for the reaction are suggested based on the spectroscopic results.

  10. Adsorption of Rhodamine B Dye from Aqueous Solution on Irvingia ...

    African Journals Online (AJOL)

    NICOLAAS

    second-order kinetics model was observed to fit the adsorption data. Solution pH ... usually released containing various dyes and heavy metals.1 In particular ...... B.S. Ogunsina, O.A. Koya and O.O. Adeosun, Deformation and frac- ture of dika ...

  11. Gamma radiolysis of aqueous solution of ascorbic acid

    International Nuclear Information System (INIS)

    Loyola V, V.M.; Azamer B, J.A.; Laviada C, A.; Luna V, P.

    1977-01-01

    A preliminary study of the gamma radiolysis of a 1.13 x 10 -4 Maqueous solution of ascorbic acid is presented. It was found that dehydroascorbic acid was the principal product at doses of about 75 Krad. An increase in the dehydroascorbic acid concentration rangins from 5 to 40% was obtained, these values depend mainly on the initial ascorbic acid concentration. (author)

  12. Sorption of europium by Haro river sand in aqueous solution

    International Nuclear Information System (INIS)

    Syed Moosa Hasany; Syed Javaid Khurshid

    1997-01-01

    The sorption of Eu(III) on Haro river sand has been investigated. Influences include composition of the sorptive medium, the concentration of sorbent and sorbate, and shaking time. Haro river sand can be exploited for the preconcentration and removal of europium from very dilute solutions, for the decontamination and treatment of radioactive waste water and effluents from nuclear installations. (Author)

  13. Preparation and Evaluation of Adsorbents from Coal and Irvingia gabonensis Seed Shell for the Removal of Cd(II and Pb(II Ions from Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    Mercy A. Ezeokonkwo

    2018-01-01

    Full Text Available Cd(II and Pb(II ions removal using adsorbents prepared from sub-bituminous coal, lignite, and a blend of coal and Irvingia gabonensis seed shells was investigated. Fourier transform infrared, scanning electron microscope and X-ray fluorescence analyses implicated hydroxyl, carbonyl, Al2O3, and SiO2 as being responsible for attaching the metal ions on the porous adsorbents. The optimum adsorption of carbonized lignite for the uptake of Cd(II and Pb(II ions from aqueous media were 80.93 and 87.85%, respectively. Batch adsorption was done by effect of adsorbent dosage, pH, contact time, temperature, particle size, and initial concentration. Equilibrium for the removal of Pb(II and Cd(II was established within 100 and 120 min respectively. Blending the lignite-derived adsorbent with I. gabonensis seed shell improved the performance significantly. More improvement was observed on modification of the blend using NaOH and H3PO4. Pb(II was preferentially adsorbed than Cd(II in all cases. Adsorption of Cd(II and Pb(II ions followed Langmuir isotherm. The adsorption kinetics was best described by pseudo-second order model. The potential for using a blend of coal and agricultural byproduct (I. gabonensis seed shell was found a viable alternative for removal of toxic heavy metals from aqueous solutions.

  14. Effective Microporosity for Enhanced Adsorption Capacity of Cr (VI) from Dilute Aqueous Solution: Isotherm and Kinetics

    OpenAIRE

    Lloyd Mukosha; Maurice S. Onyango; Aoyi Ochieng; John Siame

    2017-01-01

    The adsorbent pore structure significant to enhanced adsorption capacity of Cr (VI) from dilute aqueous solution is evaluated. As reference, low-cost micro-mesoporous activated carbon (AC) of high basicity, mesoporosity centred about 2.4 nm, and effective microporosity centred about 0.9 nm was tested for removal of Cr (VI) from dilute aqueous solution in batch mode. At pH 2 the low-cost AC exhibited highly improved Langmuir Cr (VI) capacity of 115 mg/g which was competitive to high performanc...

  15. Extraction of rare earth metals (3) from aqueous solutions containing thorium and uranyl nitrates

    International Nuclear Information System (INIS)

    Pyartman, A.K.; Kopyrin, A.A.; Berinskij, A.E.; Keskinov, V.A.

    2000-01-01

    Isotherms of extraction of rare earth metals (3) from aqueous solutions containing thorium and uranyl nitrates by solutions of tributylphosphate (TBP) and diisooctylmethylphosphonate (DIOMP) in kerosene at 298.15 Deg C and pH 1 are presented. Equations for description of interphase distribution of components of the systems considered are suggested. These equations describe distribution of components adequately in the systems of thorium nitrate (uranyl nitrate) - rare earth nitrates - (TBP, DIOMP) in the case of wide variation of phase compositions. Dependences of separation factors on composition of aqueous phase are considered [ru

  16. Uranium removal from acidic aqueous solutions by Saccharomyces cerevisiae, Debaryomyces hansenii, Kluyveromyces marxianus and Candida colliculosa

    International Nuclear Information System (INIS)

    Sarri, S.; Misaelides, P.; Papanikolaou, M.; Zamboulis, D.

    2009-01-01

    The sorption of uranium from acidic aqueous solutions (pH 4.5, C init = 10 to 1000 mg U/L) by Saccharomyces cerevisiae, Debaryomyces hansenii, Kluyveromyces marxianus and Candida colliculosa was investigated using a batch technique. The U-sorption onto Saccharomyces cerevisiae and Debaryomyces hansenii followed a Langmuir, while that onto Kluyveromyces marxianus and Candida colliculosa a Freundlich isotherm. The results demonstrated that all investigated biomasses could effectively remove uranium from acidic aqueous solutions. From all sorbents, Saccharomyces cerevisiae appeared to be the most effective with a maximum sorption capacity of 127.7 mg U/g dry biomass. (author)

  17. Ab initio molecular dynamics simulation of aqueous solution of nitric oxide in different formal oxidation states

    Science.gov (United States)

    Venâncio, Mateus F.; Rocha, Willian R.

    2015-10-01

    Ab initio molecular dynamics simulations were used to investigate the early chemical events involved in the dynamics of nitric oxide (NOrad), nitrosonium cation (NO+) and nitroxide anion (NO-) in aqueous solution. The NO+ ion is very reactive in aqueous solution having a lifetime of ∼4 × 10-13 s, which is shorter than the value of 3 × 10-10 s predicted experimentally. The NO+ reacts generating the nitrous acid as an intermediate and the NO2- ion as the final product. The dynamics of NOrad revealed the reversibly formation of a transient anion radical species HONOrad -.

  18. Pinning of phase separation of aqueous solution of hydroxypropylmethylcellulose by gelation

    Science.gov (United States)

    Kita, Rio; Kaku, Takeshi; Kubota, Kenji; Dobashi, Toshiaki

    1999-08-01

    Opalescence of the aqueous solution of hydroxypropylmethylcellulose (HPMC) induced by heating has been studied in terms of the phase diagram and the phase separation dynamics. The cloud point curve and the sol-to-gel transition curve intersected with each other at about 55 °C. Just above the cloud-point curve at which the spinodal curve has its minimum, a ring-like scattering pattern appeared corresponding to the spinodal decomposition. Temporal growth of the scattering function in the course of phase separation was studied by a time-resolved light scattering technique. The gelation pinned the phase separation (spinodal decomposition) of the aqueous HPMC solution.

  19. Effect of pH on the corrosion behaviour of SUS321 in the ammonia aqueous solution

    International Nuclear Information System (INIS)

    Park, Sang Yoon; Jeong, Y. H.; Baek, J. H.; Choi, B. K.; Lee, M. H.; Choi, B. S.; Yoon, J. H.; Lee, D. J.

    2003-02-01

    The corrosion characteristics of SUS321 for pressure vessel of SMART in pure water, ammonia aqueous solutions of pH 8.5 ∼ 11.5 at 300 .deg. C were evaluated by using static autoclaves. SUS321 specimen in the high temperature ammonia aqueous solution has weight gain or loss by the 4 reactions. And it depends on the refreshing period of the aqueous solution. So additional experiments by recirculating loop system were required to evaluate the corrosion behaviour of SUS321 in the ammonia aqueous solution

  20. Electrochemical reactions of uranyl(VI) complexes in aqueous solution, non-aqueous solvents, and ionic liquids

    International Nuclear Information System (INIS)

    Ikeda, Yasuhisa

    2006-01-01

    Author's recent experimental results on the chemistry of U(V) in aqueous solution, non-aqueous solvents, and ionic solvents by cyclic voltametry are described. The U(V) was produced by electrochemical reduction of uranyl U(VI) ions or complexes such as carbonates, DMF(N, N-dimethylformamide), DMSO(dimethylsulfoxide), acetylacetonato, and other organic polydental ligands. The produced U(V) complexes were studied by spectrophotometry using optical-transmission thin-layer electrode. The U(V) complexes in non-aqueous solvents were found to be rather stable, they undergo ligand-dissociation reaction but not disproportionation reaction. The structure and electronic spectra as well as IR spectra of the complexes were studied. The present method was further developed to study the behavior of U(V) complexes in ionic liquids as molten salts, e.g., alkaline metals chlorides. Thus, the present research contributes to understanding the chemistry of 5fl system. Application to such nuclear technology as spent fuel reprocessing is discussed. (S. Ohno)

  1. Simultaneous Extraction, Enrichment and Removal of Dyes from Aqueous Solutions Using a Magnetic Aqueous Micellar Two-Phase System

    Directory of Open Access Journals (Sweden)

    Shuanggen Wu

    2017-12-01

    Full Text Available The magnetic aqueous micellar two-phase system (MAMTPS has the advantages combined of magnetic solid phase extraction (MSPE and aqueous micellar two-phase system (AMTPS. Thus, MAMTPS based on Fe3O4 magnetic nanoparticles (MNPs and a nonionic surfactant Triton X-114 (TX-114 was developed for the extraction, enrichment and removal of three dyes (Congo red, methyl blue, and methyl violet from aqueous solutions in this study. The MNPs Fe3O4@NH2 was screened as the optimal MNPs benefiting the extraction. Then, the influencing factors of MNPs amount, TX-114 concentration, vibration time, and extraction temperature were investigated in detail. The results showed that the extraction efficiencies of three dyes almost reached 100% using MAMTPS under the optimal conditions; MAMTPS had higher extraction ability than the individual MSPE or AMTPS. Thus, MAMTPS had the advantages of simple operation, high extraction ability, easy recycling of MNPs, and short phase-separation time, which showspotential for use in the extraction and analysis of contaminants from water samples.

  2. Formation of the second organic phase during uranyl nitrate extraction from aqueous solution by 30% tributylphosphate solution in paraffin

    International Nuclear Information System (INIS)

    Yhrkin, V.G.

    1996-01-01

    For extraction systems aqueous solution of uranyl nitrate-30% solution of tributylphosphate in individual paraffins from C 13 to C 17 the influence of the second organic phase of uranyl nitrate concentration in aqueous and organic phases, the length of hydrocarbon chain of paraffin hydrocarbon and temperature from 25 to 50 deg C on formation conditions has been defected. A special method of achieving the conditions of organic phase stratification from three-phase region, involving definition of equilibrium phases composition by density and refractive index, has been elaborated for more precise definition of organic phase homogeneity region. It has been revealed that without addition of nitric acid to uranyl nitrate solution the organic phase homogeneity limits can be achieved solely on paraffins C 15 , C 16 and C 17 and only under conditions similar to equeous phase saturation in terms of uranyl nitrate. 16 refs., 2 figs

  3. Np(V) carbonates in solid state and aqueous solution

    International Nuclear Information System (INIS)

    Meinrath, G.

    1994-01-01

    The solubility of NaNpO 2 CO 3 (s) in 0.1M perchlorate solution at 25 deg C in equilibrium with 1.0% CO 2 /N 2 atmosphere has been investigated as a function of pH/lg [CO 3 2- ]. The solid phase was found hexagonal with a=1008.1±0.3 pm and c=991.1±0.2 pm. A solubility product of lg Ksp(NaNpO 2 CO 3 ) = -10.22±0.02 and a formation constant of the first Np(V) carbonato species of lg β 01 = 4.52±0.02 was evaluated. For the dicarbonato species an upper limit of lg lg β 02 2 partial pressure gave evidence that carbonato species are prevailing in solutions at both 1% and 0.03% CO 2 partial pressures. (author) 26 refs.; 4 figs.; 3 tabs

  4. Degradation of aqueous phenol solutions by coaxial DBD reactor

    Science.gov (United States)

    Dojcinovic, B. P.; Manojlovic, D.; Roglic, G. M.; Obradovic, B. M.; Kuraica, M. M.; Puric, J.

    2008-07-01

    Solutions of 2-chlorophenol, 4-chlorophenol and 2,6-dichlorophenol in bidistilled and water from the river Danube were treated in plasma reactor. In this reactor, based on coaxial dielectric barrier discharge at atmospheric pressure, plasma is formed over a thin layer of treated water. After one pass through the reactor, starting chlorophenols concentration of 20 mg/l was diminished up to 95 %. Kinetics of the chlorophenols degradation was monitored by High Pressure Liquid Chromatography method (HPLC).

  5. Chemical behaviour of plutonium in aqueous chloride solutions

    International Nuclear Information System (INIS)

    Bueppelmann, K.; Kim, J.I.

    1988-06-01

    The chemical behaviour of Plutonium has been investigated in concentrated NaCl solutions in the neutral pH range. The α-radiation induced radiolysis reactions oxidize the Cl - -ion to Cl 2 , HClO, ClO - and other species, which produce a strongly oxidizing medium. Under these conditions the Pu ions of lower oxidation states are readily oxidized to Pu(VI), which then undergo depending on the pH of the solution, various chemical reactions to produce PuO 2 Cl n , PuO 2 (ClO) m or PuO 2 (OH) x species. In addition to primary radiolysis reactions taking place in NaCl solutions, the reactions leading to the PuO 2 (Cl) n and PuO 2 (ClO) m species have been characterized and quantified systematically by spectroscopic and thermodynamic evaluation. The redox and complexation reactions of Pu ions under varying NaCl concentration, specific α-activity and pH are discussed. (orig.) [de

  6. Removal of Pb(II) ions from aqueous solution by a waste mud from copper mine industry: equilibrium, kinetic and thermodynamic study.

    Science.gov (United States)

    Ozdes, Duygu; Gundogdu, Ali; Kemer, Baris; Duran, Celal; Senturk, Hasan Basri; Soylak, Mustafa

    2009-07-30

    The objective of this study was to assess the adsorption potential of a waste mud (WM) for the removal of lead (Pb(II)) ions from aqueous solutions. The WM was activated with NaOH in order to increase its adsorption capacity. Adsorption studies were conducted in a batch system as a function of solution pH, contact time, initial Pb(II) concentration, activated-waste mud (a-WM) concentration, temperature, etc. Optimum pH was specified as 4.0. The adsorption kinetic studies indicated that the overall adsorption process was best described by pseudo-second-order kinetics. The equilibrium adsorption capacity of a-WM was obtained by using Langmuir and Freundlich isotherm models and both models fitted well. Adsorption capacity for Pb(II) was found to be 24.4 mg g(-1) for 10 g L(-1) of a-WM concentration. Thermodynamic parameters including the Gibbs free energy (Delta G degrees), enthalpy (Delta H degrees), and entropy (DeltaS degrees) indicated that the adsorption of Pb(II) ions on the a-WM was feasible, spontaneous and endothermic, at temperature range of 0-40 degrees C. Desorption studies were carried out successfully with diluted HCl solutions. The results indicate that a-WM can be used as an effective and no-cost adsorbent for the treatment of industrial wastewaters contaminated with Pb(II) ions.

  7. Removal of Pb(II) ions from aqueous solution by a waste mud from copper mine industry: Equilibrium, kinetic and thermodynamic study

    International Nuclear Information System (INIS)

    Ozdes, Duygu; Gundogdu, Ali; Kemer, Baris; Duran, Celal; Senturk, Hasan Basri; Soylak, Mustafa

    2009-01-01

    The objective of this study was to assess the adsorption potential of a waste mud (WM) for the removal of lead (Pb(II)) ions from aqueous solutions. The WM was activated with NaOH in order to increase its adsorption capacity. Adsorption studies were conducted in a batch system as a function of solution pH, contact time, initial Pb(II) concentration, activated-waste mud (a-WM) concentration, temperature, etc. Optimum pH was specified as 4.0. The adsorption kinetic studies indicated that the overall adsorption process was best described by pseudo-second-order kinetics. The equilibrium adsorption capacity of a-WM was obtained by using Langmuir and Freundlich isotherm models and both models fitted well. Adsorption capacity for Pb(II) was found to be 24.4 mg g -1 for 10 g L -1 of a-WM concentration. Thermodynamic parameters including the Gibbs free energy (ΔG o ), enthalpy (ΔH o ), and entropy (ΔS o ) indicated that the adsorption of Pb(II) ions on the a-WM was feasible, spontaneous and endothermic, at temperature range of 0-40 o C. Desorption studies were carried out successfully with diluted HCl solutions. The results indicate that a-WM can be used as an effective and no-cost adsorbent for the treatment of industrial wastewaters contaminated with Pb(II) ions.

  8. Removal of Pb(II) ions from aqueous solution by a waste mud from copper mine industry: Equilibrium, kinetic and thermodynamic study

    Energy Technology Data Exchange (ETDEWEB)

    Ozdes, Duygu; Gundogdu, Ali; Kemer, Baris; Duran, Celal; Senturk, Hasan Basri [Department of Chemistry, Karadeniz Technical University, Faculty of Arts and Sciences, 61080 Trabzon (Turkey); Soylak, Mustafa, E-mail: soylak@erciyes.edu.tr [Department of Chemistry, Erciyes University, Faculty of Arts and Sciences, 38039 Kayseri (Turkey)

    2009-07-30

    The objective of this study was to assess the adsorption potential of a waste mud (WM) for the removal of lead (Pb(II)) ions from aqueous solutions. The WM was activated with NaOH in order to increase its adsorption capacity. Adsorption studies were conducted in a batch system as a function of solution pH, contact time, initial Pb(II) concentration, activated-waste mud (a-WM) concentration, temperature, etc. Optimum pH was specified as 4.0. The adsorption kinetic studies indicated that the overall adsorption process was best described by pseudo-second-order kinetics. The equilibrium adsorption capacity of a-WM was obtained by using Langmuir and Freundlich isotherm models and both models fitted well. Adsorption capacity for Pb(II) was found to be 24.4 mg g{sup -1} for 10 g L{sup -1} of a-WM concentration. Thermodynamic parameters including the Gibbs free energy ({Delta}G{sup o}), enthalpy ({Delta}H{sup o}), and entropy ({Delta}S{sup o}) indicated that the adsorption of Pb(II) ions on the a-WM was feasible, spontaneous and endothermic, at temperature range of 0-40 {sup o}C. Desorption studies were carried out successfully with diluted HCl solutions. The results indicate that a-WM can be used as an effective and no-cost adsorbent for the treatment of industrial wastewaters contaminated with Pb(II) ions.

  9. Interaction between tetracycline and smectite in aqueous solution.

    Science.gov (United States)

    Li, Zhaohui; Chang, Po-Hsiang; Jean, Jiin-Shuh; Jiang, Wei-Teh; Wang, Chih-Jen

    2010-01-15

    The fate and transport of commonly used antibiotics in soil and groundwater have attracted renewed studies due to increased sensitivities of analytical instruments and thus frequent detections of these compounds even in treated wastewater. Smectite, an important soil component, has large surface area and high cation exchange capacity, while tetracycline (TC) can exist in different forms and charges under different pH conditions. Thus, the interaction between smectite and TC in aqueous systems is of great importance. This research focused on elucidating the mechanisms of TC uptake by smectite, in terms of TC adsorption, cation desorption, and pH changes associated with TC adsorption by smectite and intercalation in smectite. TC adsorption onto smectite was a relatively fast process even though most of the adsorption sites were in the interlayer position involved in intercalation as confirmed by the expansion of d(001) spacing. The TC adsorption capacity was equivalent to 0.74-1.11 times the cation exchange capacity for three of the four smectite minerals studied. Accompanying TC adsorption was simultaneous adsorption of H(+), resulting in protonation of TC on the dimethylamine group. At higher TC input concentrations further adsorption of H(+) resulted in the ratio of H(+) adsorbed to TC adsorbed greater than one, suggesting that additionally adsorbed H(+) could serve as counterions to partially offset the negative charges on the tricarbonyl or phenolic diketone functional groups. The positive correlations between cations desorbed and TC adsorbed, as well as TC adsorbed and H(+) adsorbed, provided a first time evidence to confirm cation exchange as the main mechanism of TC uptake, even under neutral pH conditions.

  10. Influence of particles on sonochemical reactions in aqueous solutions.

    Science.gov (United States)

    Keck, A; Gilbert, E; Köster, R

    2002-05-01

    Numerous publications deal with the possible application of ultrasound for elimination of organic pollutants as a tool for water pollution abatement. Most of the experiments were performed in pure water under laboratory conditions. For developing technologies that hold promise it is necessary to investigate the effect of ultrasound in natural systems or waste water where particulate matter could play an important role. In this paper the influence of quartz particles (2-25 microm) on the chemical effects of ultrasound in aqueous system using a high power ultrasound generator (68-1028 kHz, 100 W, reactor volume 500 ml) is reported. In pure water in dependence on particle size, concentration and frequency the formation rate of hydrogen peroxide under Ar/O2 (4:1) shows a maximum using 206 kHz in presence of 3-5 microm quartz particles (4-8 g/l). Under these conditions the yield of peroxide is higher than without quartz. Additionally under N2/O2 (4:1) besides hydrogen peroxide the formation of nitrite/nitrate was measured. Compared to pure water quartz particle depressed the formation of nitrite/nitrate up to 10-fold but not the formation of H2O2. According to the results of H2O2 formation the elimination of organic compounds by sonolysis (206 kHz) and the influence of quartz particles were investigated. As organic compounds salicylic acid, 2-chlorobenzoic acid and p-toluenesulfonic acid were used. The influence of quartz on the oxidation of organic compounds (206 kHz) is similar to that on the formation of H2O2.

  11. Photoionization of rhodamine dyes adsorbed at the aqueous solution surfaces investigated by synchrotron radiation

    International Nuclear Information System (INIS)

    Seno, Koichiro; Ishioka, Toshio; Harata, Akira; Hatano, Yoshihiko

    2002-01-01

    Photoionization spectroscopy using synchrotron radiation as a photon source was applied to the aqueous solution surfaces of rhodamine B (RhB), rhodamine 6G (Rh6G), and rhodamine 101 (Rh101) with their concentration of 0-100 μmol dm -3 . Synchrotron radiation was irradiated upon the solution surface between two electrodes in the photon energy range of 4-7 eV, and photoionization current was measured by a pico-ammeter. The photocurrent for each of the rhodamine aqueous solution surface showed an increase with the photon energy above a threshold photon energy. The photoionization threshold of RhB at the aqueous solution surface was 5.6 eV, which was smaller than that in the gas phase. The intensity of photoionization current of Rh6G was smaller than that of RhB or Rh101. Photoionization processes and the state of Rhodamine dye molecules at the aqueous solution surface were discussed in connection with results of surface tension measurements. (author)

  12. Nuclear magnetic relaxation in aqueous praseodymium and europium solutions

    International Nuclear Information System (INIS)

    Lopez, J.L.; Diaz, D.

    1991-01-01

    A general theory for the relaxation of the nuclear spin in paramagnetic complexes where the electronic spin is within a slow-movement regime was presented by Benetis et al. and applied to d-group elements (Ni 2+ , Co 2+ ). This paper show the possibility to apply such formalism to f-group elements and it was developed for S=3(Eu 3+ ). A group of magnitudes characterizing the microstructure and dynamics of these solutions is reported with the approximations used. The dispersion of the nuclear magnetic relaxation (NMRD) for the proton of the variable field was also assessed which had a similar behaviour to what was experimentally reported

  13. Degradation of BTEX in aqueous solution by hydrodynamic cavitation

    Energy Technology Data Exchange (ETDEWEB)

    Braeutigam, P.; Wu, Z.-L.; Stark, A.; Ondruschka, B. [Institute for Technical Chemistry and Environmental Chemistry, Friedrich Schiller University, Jena (Germany)

    2009-05-15

    A self-made low-pressure device (up to 100 psi) for hydrodynamic cavitation was tested with the reaction of BTEX (benzene, toluene, ethylbenzene, and xylenes) in water. Experimental parameters, such as inlet pressure, solution temperature, and concentration of the chosen substrates, as well as the effect of different restrictions were investigated. The energy efficiency of the process was measured in comparison to two acoustic cavitation systems (24 and 850 kHz). The products of the BTEX degradation were identified and a pyrolytic degradation pathway is concluded. (Abstract Copyright [2009], Wiley Periodicals, Inc.)

  14. Molecular Dynamics Simulation Studies of Caffeine Aggregation in Aqueous Solution

    OpenAIRE

    Tavagnacco, Letizia; Schnupf, Udo; Mason, Philip E.; Saboungi, Marie-Louise; Cesàro, Attilio; Brady, John W.

    2011-01-01

    Molecular dynamics simulations were carried out on a system of eight independent caffeine molecules in a periodic box of water at 300 K, representing a solution near the solubility limit for caffeine at room temperature, using a newly-developed CHARMM-type force field for caffeine in water. Simulations were also conducted for single caffeine molecules in water using two different water models (TIP3P and TIP4P). Water was found to structure in a complex fashion around the planar caffeine molec...

  15. Removal of heavy metals from aqueous solution by Carrot residues

    International Nuclear Information System (INIS)

    Eslamzadeh, T.; Nasernejad, B.; Bonakdar Pour, B.; Zamani, A.; Esmaail-Beygi, M.

    2004-01-01

    The removal of Copper(II), Zinc(II), and Chromium (III) from wastewater by carrot residues was investigated to evaluate cation exchange capacity. The effects of solution P H and co-ions were studied in batch experiments. Adsorption equilibria were initially rapidly established, and then decreased markedly after 10 min. Column experiments were carried out in a glass column filled with carrot residues to evaluate the metal removal capacity. The influences of the feed concentration and feed rate were also studied in order to compare the dynamic capacity for metal binding in different feed concentrations

  16. Radiolysis of dilute aqueous solutions of cesium iodide

    International Nuclear Information System (INIS)

    Gorbovitskaya, T.I.; Galinkin, D.L.; Kants, L.K.; Tiliks, Yu.E.; Kotelkin, I.M.; Luzanova, L.M.

    1993-01-01

    Study of physical-chemical processes in the NPP containment by severe accident is carried out. Radiolysis of reactor cooling water containing iodine and cesium radionuclides penetrated therein in the course of accident is considered as of such processes. Role of ionizing radiation in the process of formation and release of ecologically hazardous volatile forms of radioiodine from reactor water into environment is studied. Experiments on radiolysis of CsI diluted water solutions are carried out. The data obtained were used for clarification of radiolysis mechanism for iodine-containing water system, enabling forecast of iodine behaviour in the course of the accident. 5 refs., 4 figs., 1 tab

  17. Relation between the adsorbed quantity and the immersion enthalpy in catechol aqueous solutions on activated carbons.

    Science.gov (United States)

    Moreno-Piraján, Juan Carlos; Blanco, Diego; Giraldo, Liliana

    2012-01-01

    An activated carbon, Carbochem(TM)-PS230, was modified by chemical and thermal treatment in flow of H(2), in order to evaluate the influence of the activated carbon chemical characteristics in the adsorption of the catechol. The catechol adsorption in aqueous solution was studied along with the effect of the pH solution in the adsorption process of modified activated carbons and the variation of immersion enthalpy of activated carbons in the aqueous solutions of catechol. The interaction solid-solution is characterized by adsorption isotherms analysis, at 298 K and pH 7, 9 and 11 in order to evaluate the adsorption value above and below that of the catechol pK(a). The adsorption capacity of carbons increases when the solution pH decreases. The retained amount increases slightly in the reduced carbon to maximum adsorption pH and diminishes in the oxidized carbon. Similar conclusions are obtained from the immersion enthalpies, whose values increase with the solute quantity retained. In granular activated carbon (CAG), the immersion enthalpies obtained are between 21.5 and 45.7 J·g(-1) for catechol aqueous solutions in a range of 20 at 1500 mg·L(-1).

  18. Relation Between the Adsorbed Quantity and the Immersion Enthalpy in Catechol Aqueous Solutions on Activated Carbons

    Directory of Open Access Journals (Sweden)

    Liliana Giraldo

    2011-12-01

    Full Text Available An activated carbon, CarbochemTM—PS230, was modified by chemical and thermal treatment in flow of H2, in order to evaluate the influence of the activated carbon chemical characteristics in the adsorption of the catechol. The catechol adsorption in aqueous solution was studied along with the effect of the pH solution in the adsorption process of modified activated carbons and the variation of immersion enthalpy of activated carbons in the aqueous solutions of catechol. The interaction solid-solution is characterized by adsorption isotherms analysis, at 298 K and pH 7, 9 and 11 in order to evaluate the adsorption value above and below that of the catechol pKa. The adsorption capacity of carbons increases when the solution pH decreases. The retained amount increases slightly in the reduced carbon to maximum adsorption pH and diminishes in the oxidized carbon. Similar conclusions are obtained from the immersion enthalpies, whose values increase with the solute quantity retained. In granular activated carbon (CAG, the immersion enthalpies obtained are between 21.5 and 45.7 J·g−1 for catechol aqueous solutions in a range of 20 at 1500 mg·L−1.

  19. Interaction between lactose and cadmium chloride in aqueous solutions as seen by diffusion coefficients measurements

    International Nuclear Information System (INIS)

    Verissimo, Luis M.P.; Gomes, Joselaine C.S.; Romero, Carmen; Esteso, Miguel A.; Sobral, Abilio J.F.N.; Ribeiro, Ana C.F.

    2013-01-01

    Highlights: ► Diffusion coefficients of aqueous systems containing lactose and cadmium chloride. ► Influence of the lactose on the diffusion of cadmium chloride. ► Interactions between Cd 2+ and lactose. -- Abstract: Diffusion coefficients of an aqueous system containing cadmium chloride 0.100 mol · dm −3 and lactose at different concentrations at 25 °C have been measured, using a conductimetric cell and an automatic apparatus to follow diffusion. The cell relies on an open-ended capillary method and a conductimetric technique is used to follow the diffusion process by measuring the resistance of a solution inside the capillaries, at recorded times. From these results and by ab initio calculations, it was possible to obtain a better understanding of the effect of lactose on transport of cadmium chloride in aqueous solutions

  20. Adsorption of gold (III) from aqueous solutions on bagasse ash

    International Nuclear Information System (INIS)

    Hussain, G.; Khan, M.A.

    2011-01-01

    To assess the potential of cheap biomass materials for the recovery of gold from industrial, and electroplating waste water effluents, adsorption of gold (III) from dilute solutions of hydrochloric acid on bagasse ash has been studied under various experimental conditions by using batch technique. Percentage extraction of gold (III) on bagasse ash was determined from its distribution coefficients as a function of contact time, pH, adsorbent, adsorbate concentrations, and temperature. The uptake of gold (III) by bagasse ash is time, pH, metal concentration, amount of adsorbate, and temperature dependent. Adsorption data have been interpreted in terms of Langmuir, and the Freundlich equations. Thermodynamic parameters for the adsorption of gold (III) on bagasse ash have been determined at three different temperatures. The positive value of heat of adsorption; delta H 44.52 kJ/mol shows that the adsorption of gold (III) on bagasse ash is endothermic where as the negative value of delta G = -0.5303 kJ/mol at 318 K shows the spontaneity of the process. Delta G becomes more negative with increase in temperature which shows that the adsorption is more favorable at higher temperatures. Under the optimal adsorption conditions the adsorption capacity of gold is 0.70 mg /g of the adsorbent out of which 0.65 mg of gold gets desorbed with 0.1 % thiourea solution. (author)