Numerical tsunami simulations in the western Pacific Ocean and East China Sea from hypothetical M 9 earthquakes along the Nankai trough

Science.gov (United States)

Harada, Tomoya; Satake, Kenji; Furumura, Takashi

2017-04-01

We carried out tsunami numerical simulations in the western Pacific Ocean and East China Sea in order to examine the behavior of massive tsunami outside Japan from the hypothetical M 9 tsunami source models along the Nankai Trough proposed by the Cabinet Office of Japanese government (2012). The distribution of MTHs (maximum tsunami heights for 24 h after the earthquakes) on the east coast of China, the east coast of the Philippine Islands, and north coast of the New Guinea Island show peaks with approximately 1.0-1.7 m，4.0-7.0 m，4.0-5.0 m, respectively. They are significantly higher than that from the 1707 Ho'ei earthquake (M 8.7), the largest earthquake along the Nankai trough in recent Japanese history. Moreover, the MTH distributions vary with the location of the huge slip(s) in the tsunami source models although the three coasts are far from the Nankai trough. Huge slip(s) in the Nankai segment mainly contributes to the MTHs, while huge slip(s) or splay faulting in the Tokai segment hardly affects the MTHs. The tsunami source model was developed for responding to the unexpected occurrence of the 2011 Tohoku Earthquake, with 11 models along the Nanakai trough, and simulated MTHs along the Pacific coasts of the western Japan from these models exceed 10 m, with a maximum height of 34.4 m. Tsunami propagation was computed by the finite-difference method of the non-liner long-wave equations with the Corioli's force and bottom friction (Satake, 1995) in the area of 115-155 ° E and 8° S-40° N. Because water depth of the East China Sea is shallower than 200 m, the tsunami propagation is likely to be affected by the ocean bottom fiction. The 30 arc-seconds gridded bathymetry data provided by the General Bathymetric Chart of the Oceans (GEBCO-2014) are used. For long propagation of tsunami we simulated tsunamis for 24 hours after the earthquakes. This study was supported by the"New disaster mitigation research project on Mega thrust earthquakes around Nankai

Characterizing structures on borehole images and logging data of the Nankai trough accretionary prism: new insights

Science.gov (United States)

Jurado, Maria Jose

2016-04-01

IODP has extensively used the D/V Chikyu to drill the Kumano portion of the Nankai Trough, including two well sites within the Kumano Basin. IODP Expeditions 338 and 348 drilled deep into the inner accretionary prism south of the Kii Peninsula collecting a suite of LWD data, including natural gamma ray, electrical resistivity logs and borehole images, suitable to characterize structures (fractures and faults) inside the accretionary prism. Structural interpretation and analysis of logging-while-drilling data in the deep inner prism revealed intense deformation of a generally homogenous lithology characterized by bedding that dips steeply (60-90°) to the NW, intersected by faults and fractures. Multiple phases of deformation are characterized. IODP Expedition borehole images and LWD data acquired in the last decade in previous and results of NantroSEIZE IODP Expeditions (314, 319) were also analyzed to investigate the internal geometries and structures of the Nankai Trough accretionary prism. This study focused mainly on the characterization of the different types of structures and their specific position within the accretionary prism structures. New structural constraints and methodologies as well as a new approach to the characterization of study of active structures inside the prism will be presented.

Prominent reflector beneath around the segmentation boundary between Tonankai-Nankai earthquake area

Science.gov (United States)

Nakanishi, A.; Shimomura, N.; Fujie, G.; Kodaira, S.; Obana, K.; Takahashi, T.; Yamamoto, Y.; Yamashita, M.; Takahashi, N.; Kaneda, Y.; Mochizuki, K.; Kato, A.; Iidaka, T.; Kurashimo, E.; Shinohara, M.; Takeda, T.; Shiomi, K.

2013-12-01

In the Nankai Trough subduction seismogenic zone, the Nankai and Tonankai earthquakes had often occurred simultaneously, and caused a great event. In most cases, first break of such large events of Nankai Trough usually begins from southwest off the Kii Peninsula so far. The idea of split Philippine Sea plate between the Kii Peninsula and the Shikoku Island, which explains seismicity, tectonic background, receiver function image and historical plate motion, was previously suggested. Moreover, between the Kii Peninsula and the Shikoku Island, there is a gap of deep low-frequency events observed in the belt-like zone along the strike of the subducting Philippine Sea plate. In 2010 and 2011, we conducted the large-scale high-resolution wide-angle and reflection (MCS) seismic study, and long-term observation from off Shikoku and Kii Peninsula. Marine active source seismic data have been acquired along grid two-dimensional profiles having the total length of ~800km/year. A three-dimensional seismic tomography using active and passive seismic data observed both land and ocean bottom stations have been also performed. From those data, we found a possible prominent reflector imaged in the offshore side in the Kii channel at the depth of ~18km. The velocity just beneath the reflector cannot be determined due to the lack of ray paths. Based of the amplitude information, we interpret the reflector as the forearc Moho based on the velocity gap (from ~6.4km/s to ~7.4km/s). However, the reflector is shallower than the forearc Moho of other area along the Nankai Trough. Similar reflectors are recognized along other seismic profiles around the Kii channel. In this presentation, we will show the result of structure analysis to understand the peculiar structure including the prominent reflector around the Kii channel. Relation between the structure and the existence of the segmentation of the Nankai megathrust earthquake or seismic gap of the deep low-frequency events will be also

Deep seismic transect across the Tonankai earthquake area obtained from the onshore- offshore wide-angle seismic study

Science.gov (United States)

Nakanishi, A.; Obana, K.; Kodaira, S.; Miura, S.; Fujie, G.; Ito, A.; Sato, T.; Park, J.; Kaneda, Y.; Ito, K.; Iwasaki, T.

2008-12-01

In the Nankai Trough subduction seismogenic zone, M8-class great earthquake area can be divided into three segments; they are source regions of the Nankai, Tonankai and presumed Tokai earthquakes. The Nankai and Tonankai earthquakes had often occurred simultaneously, and caused a great event. Hypocenters of these great earthquakes were usually located off the cape Shiono, Kii Peninsula, and the rupture propagated westwards and eastwards, respectively. To obtain the deep structure of the down-dip limit of around the Nankai Trough seismogenic zone, the segment boundary and first break area off the Kii Peninsula, the onshore-offshore wide-angle seismic studies was conducted in the western and eastern part of the Kii Peninsula and their offshore area in 2004 and 2006, respectively. The result of the seismic study in 2004 is mainly shown here. Structural images along the onshore and offshore profiles have already been separately obtained. In this study, an onshore-offshore integrated image of the western part of the Kii Peninsula, ~400km in a total length, is obtained from first arrival tomography and traveltime mapping of reflection phases by combining dataset of 13 land explosions, 2269 land stations, 36 OBSs and 1806 offshore airgun shots. The subduction angle of the Philippine Sea plate (PSP) gradually increases landward up to ~20-25 degree. Beneath the onshore part, the subducting PSP is estimated at ~5km shallower than that previously derived from seismicity. Low frequency earthquakes (identified and picked by Japan Meteorological Agency) are relocated around the plate interface of the subducting PSP by using the deep seismic transect obtained in this study. The offshore research is part of 'Structure research on plate dynamics of the presumed rupture zone of the Tonankai-Nankai Earthquakes' funded by Ministry of Education, Culture, Sports, Science and Technology (MEXT). The onshore research carried by the Kyoto University is part of 'Special Project for

Dense Ocean Floor Network for Earthquakes and Tsunamis; DONET/ DONET2, Part2 -Development and data application for the mega thrust earthquakes around the Nankai trough-

Science.gov (United States)

Kaneda, Y.; Kawaguchi, K.; Araki, E.; Matsumoto, H.; Nakamura, T.; Nakano, M.; Kamiya, S.; Ariyoshi, K.; Baba, T.; Ohori, M.; Hori, T.; Takahashi, N.; Kaneko, S.; Donet Research; Development Group

2010-12-01

Yoshiyuki Kaneda Katsuyoshi Kawaguchi*, Eiichiro Araki*, Shou Kaneko*, Hiroyuki Matsumoto*, Takeshi Nakamura*, Masaru Nakano*, Shinichirou Kamiya*, Keisuke Ariyoshi*, Toshitaka Baba*, Michihiro Ohori*, Narumi Takakahashi*, and Takane Hori** * Earthquake and Tsunami Research Project for Disaster Prevention, Leading Project , Japan Agency for Marine-Earth Science and Technology (JAMSTEC) **Institute for Research on Earth Evolution, Japan Agency for Marine-Earth Science and Technology (JAMSTEC) DONET (Dense Ocean Floor Network for Earthquakes and Tsunamis) is the real time monitoring system of the Tonankai seismogenic zones around the Nankai trough southwestern Japan. We were starting to develop DONET to perform real time monitoring of crustal activities over there and the advanced early warning system. DONET will provide important and useful data to understand the Nankai trough maga thrust earthquake seismogenic zones and to improve the accuracy of the earthquake recurrence cycle simulation. Details of DONET concept are as follows. 1) Redundancy, Extendable function and advanced maintenance system using the looped cable system, junction boxes and the ROV/AUV. DONET has 20 observatories and incorporated in a double land stations concept. Also, we are developed ROV for the 10km cable extensions and heavy weight operations. 2) Multi kinds of sensors to observe broad band phenomena such as long period tremors, very low frequency earthquakes and strong motions of mega thrust earthquakes over M8: Therefore, sensors such as a broadband seismometer, an accelerometer, a hydrophone, a precise pressure gauge, a differential pressure gauge and a thermometer are equipped with each observatory in DONET. 3) For speedy detections, evaluations and notifications of earthquakes and tsunamis: DONET system will be deployed around the Tonankai seismogenic zone. 4) Provide data of ocean floor crustal deformations derived from pressure sensors: Simultaneously, the development of data

Amplification of tsunami heights by delayed rupture of great earthquakes along the Nankai trough

Science.gov (United States)

Imai, K.; Satake, K.; Furumura, T.

2010-04-01

We investigated the effect of delayed rupture of great earthquakes along the Nankai trough on tsunami heights on the Japanese coast. As the tsunami source, we used a model of the 1707 Hoei earthquake, which consists of four segments: Tokai, Tonankai, and two Nankai segments. We first searched for the worst case, in terms of coastal tsunami heights, of rupture delay time on each segment, on the basis of superposition principle for the linear long wave theory. When the rupture starts on the Tonankai segment, followed by rupture on the Tokai segment 21 min later, as well as the eastern and western Nankai segments 15 and 28 min later, respectively, the average coastal tsunami height becomes the largest. To quantify the tsunami amplification, we compared the coastal tsunami heights from the delayed rupture with those from the simultaneous rupture model. Along the coasts of the sea of Hyu'uga and in the Bungo Channel, the tsunami heights become significantly amplified (>1.4 times larger) relative to the simultaneous rupture. Along the coasts of Tosa Bay and in the Kii Channel, the tsunami heights become amplified about 1.2 times. Along the coasts of the sea of Kumano and Ise Bay, and the western Enshu coast, the tsunami heights become slightly smaller for the delayed rupture. Along the eastern Enshu coast, the coast of Suruga Bay, and the west coast of Sagami Bay, the tsunami heights become amplified about 1.1 times.

Temperature Limit of the Deep Subseafloor Biosphere in the Nankai Trough Subduction Zone off Cape Muroto (IODP T-Limit Expedition 370)

Science.gov (United States)

Morono, Y.; Hauer, V. B.; Inagaki, F.; Kubo, Y.; Maeda, L.; Scientists, E.

2017-12-01

Expedition 370 of the International Ocean Discovery Program (IODP) aimed to explore the limits of life in the deep subseafloor biosphere at a location where elevated heat flow lets temperature increase with sediment depth beyond the known maximum of microbial life ( 120°C) at 1.2 km below the seafloor. Such conditions are met in the protothrust zone of the Nankai Trough off Cape Muroto, Japan, where Site C0023 was established in the vicinity of ODP Sites 808 and 1174 at a water depth of 4776 m using the drilling vessel DV Chikyu. Hole C0023A was cored down to a total depth of 1180 meters below seafloor, offshore sampling and research was combined with simultaneous shore-based investigations at the Kochi Core Center (KCC), and long-term temperature observations were started (Heuer et al., 2017). The primary scientific objectives of Expedition 370 are (a) to detect and investigate the presence or absence of life and biological processes at the biotic-abiotic transition of the deep subseafloor with unprecedented analytical sensitivity and precision; (b) to comprehensively study the factors that control biomass, activity, and diversity of microbial communities; and (c) to elucidate if continuous or episodic flow of fluids containing thermogenic and/or geogenic nutrients and energy substrates support subseafloor microbial communities in the Nankai Trough accretionary complex (Hinrichs et al., 2016). This contribution will highlight the scientific approach of our field-work and preliminary expedition results by shipboard and shorebased activities. Hinrichs K-U, Inagaki F, Heuer VB, Kinoshita M, Morono Y, Kubo Y (2016) Expedition 370 Scientific Prospectus: T-Limit of the Deep Biosphere off Muroto (T-Limit). International Ocean Discovery Program. http://dx.doi.org/10.14379/iodp.sp.370.2016 Heuer VB, Inagaki F, Morono Y, Kubo Y, Maeda L, the Expedition 370 Scientists (2017) Expedition 370 Preliminary Report: Temperature Limit of the Deep Biosphere off Muroto. International

Tsunami Scenarios Based on Interseismic Models Along the Nankai Trough, Japan, From Seafloor and Onshore Geodesy

Science.gov (United States)

Watanabe, Shun-ichi; Bock, Yehuda; Melgar, Diego; Tadokoro, Keiichi

2018-03-01

The recent availability of Global Positioning System-Acoustic seafloor geodetic observations enables us to resolve the spatial distribution of the slip deficit rate near the Nankai trough, southwestern Japan. Considering a tectonic block model and the transient deformation due to the major earthquakes in this area, the slip deficit rate between the two relevant blocks can be estimated. In this study, we remove the time-dependent postseismic deformation of the 2004 southeastern off the Kii Peninsula earthquakes (MJMA 7.1, 7.4), which had led to the underestimation of the slip deficit rate in earlier studies. We model the postearthquake viscoelastic relaxation using the 3D finite element model with bi-viscous Burgers rheology, as well as the afterslip on the finite faults. The corrected Global Positioning System-Acoustic and land-based Global Navigation Satellite Systems data are aligned to the existing tectonic model and used to estimate the slip deficit rate on the plate boundary. We then calculate the coseismic displacements and tsunami wave propagation with the simple assumption that a hundred years of constant slip deficit accumulation was released instantaneously. To evaluate the influence of uncertainties in the plate interface geometry on a tsunami model for the Nankai trough, we investigated two different geometries and performed checkerboard inversion simulations. Although the two models indicate roughly similar results, the peak height of the tsunami wave and its arrival time at several points are significantly different in terms of the expected hazard.

Numerical experiment on tsunami deposit distribution process by using tsunami sediment transport model in historical tsunami event of megathrust Nankai trough earthquake

Science.gov (United States)

Imai, K.; Sugawara, D.; Takahashi, T.

2017-12-01

A large flow caused by tsunami transports sediments from beach and forms tsunami deposits in land and coastal lakes. A tsunami deposit has been found in their undisturbed on coastal lakes especially. Okamura & Matsuoka (2012) found some tsunami deposits in the field survey of coastal lakes facing to the Nankai trough, and tsunami deposits due to the past eight Nankai Trough megathrust earthquakes they identified. The environment in coastal lakes is stably calm and suitable for tsunami deposits preservation compared to other topographical conditions such as plains. Therefore, there is a possibility that the recurrence interval of megathrust earthquakes and tsunamis will be discussed with high resolution. In addition, it has been pointed out that small events that cannot be detected in plains could be separated finely (Sawai, 2012). Various aspects of past tsunami is expected to be elucidated, in consideration of topographical conditions of coastal lakes by using the relationship between the erosion-and-sedimentation process of the lake bottom and the external force of tsunami. In this research, numerical examination based on tsunami sediment transport model (Takahashi et al., 1999) was carried out on the site Ryujin-ike pond of Ohita, Japan where tsunami deposit was identified, and deposit migration analysis was conducted on the tsunami deposit distribution process of historical Nankai Trough earthquakes. Furthermore, examination of tsunami source conditions is possibly investigated by comparison studies of the observed data and the computation of tsunami deposit distribution. It is difficult to clarify details of tsunami source from indistinct information of paleogeographical conditions. However, this result shows that it can be used as a constraint condition of the tsunami source scale by combining tsunami deposit distribution in lakes with computation data.

Regional distribution of volcaniclastic layer and its implication for segmentation of the Nankai seismogenic zone

Science.gov (United States)

Sasaki, T.; Lim, J.; Higashi, M.; Park, J.

2010-12-01

The Nankai Trough is known as one of the best-suited convergent plate margins for studying accretionary prism growth as well as subduction zone earthquakes. Along the Nankai accretionary margin off southwest Japan, the Shikoku Basin which formed 26-15 Ma as backarc spreading in the Philippine Sea Plate is being subducted about 4 cm/year to the northwest. The Deep Sea Drilling Project (DSDP) and Ocean Drilling Program (ODP) penetrated the Nankai accretionary prism and the incoming sedimentary section along the Ashizuri and Muroto transects, off Shikoku Island. Also, Integrated Ocean Drilling Program (IODP), which represented just one part of a multi-stage project known as the Nankai Trough Seismogenic Zone Experiment (NanTroSEIZE) has been conducting drilling cruises now. IODP Expedition 322 in 2009, the coring was carried out at two drilling sites on the northern part of the Shikoku Basin in the subducting Philippine Sea plate. One of the major achievements of Expedition 322 is a discovery of late Miocene (10.2-7.6 Ma) tuffaceous and volcaniclastic sandstone layer (Underwood et al., IODP Prel. Rept. 322, 2009) that has not been previously recognized in the Nankai Trough. Based on age and volcanic sand content analysis, these volcaniclastic layers were unique to the Shikoku Basin off Kii Peninsula. The closest source of this volcanic layer was supposed to be the Izu-Bonin arc. Subducted sediments ultimately affect subduction zone geochemistry, thermal structure, and seismogenesis. High porosity of the volcaniclastic sandstone layer suggests the transportation of fluid to the subduction zone, it might affect the initiation and evolution of the decollement zone or plate boundary fault in the Nankai Trough. We interpreted single channel and multichannel seismic reflection profiles that have been acquired in the Nankai Trough margin by Japan Agency for Marine-Earth Science and Technology (JAMSTEC) since the year of 1997. We tried to map the major seismic layers such as

Heat Flow Variation along the Nankai Trough Floor Correlated with the Structure of the Shikoku Basin Oceanic Crust

Science.gov (United States)

Yamano, M.; Kawada, Y.; Gao, X.

2016-12-01

Surface heat flow observed on the floor of the Nankai Trough, near the trench axis, is highly variable and does not well correspond to the seafloor age of the incoming Philippine Sea plate (Shikoku Basin). Recent detailed measurements between 133.5°E and 137°E revealed that heat flow on the trough floor significantly varies along the trough. The most conspicuous variation is found around 136°E. Heat flow is extremely high and variable between 135°E and 136°E, much higher than the value estimated from the age. On the east of 136°E, heat flow gradually decreases eastward over 50 km to the value nearly consistent with the age with no appreciable scatter. Elevated heat flow on the trough floor can be attributed to vigorous fluid circulation in a permeable layer (aquifer) in the subducted oceanic crust, which efficiently transports heat upward along the plate interface (Spinelli and Wang, 2008). The heat flow variation around 136°E may therefore arise from variation in the permeability structure of the crustal aquifer. A probable cause of the heterogeneity in the aquifer permeability is a structure boundary in the incoming Shikoku Basin, the boundary between the younger part on the west formed by spreading in NE-SW direction and the older part on the east formed by E-W spreading. It is located around 136°E, about the same place as the heat flow distribution boundary. A possible additional source of variation in the permeability structure is the geometry of the subducted Philippine Sea plate. A prominent bend in the subducted plate between 135°E and 136°E, which corresponds to the high heat flow area on the trough floor, may have fractured the oceanic crust and enhanced the aquifer permeability. We evaluated the influence of variations in the aquifer permeability on the thermal structure through 3D numerical modelling using a high thermal-conductivity proxy for heat transport by fluid flow. A sharp along-strike change in the permeability of the subducted

Hydro-bio-geomechanical properties of hydrate-bearing sediments from Nankai Trough

Science.gov (United States)

Santamarina, J.C.; Dai, Shifeng; Terzariol, M.; Jang, Jeonghwan; Waite, William F.; Winters, William J.; Nagao, J.; Yoneda, J.; Konno, Y.; Fujii, T.; Suzuki, K.

2015-01-01

Natural hydrate-bearing sediments from the Nankai Trough, offshore Japan, were studied using the Pressure Core Characterization Tools (PCCTs) to obtain geomechanical, hydrological, electrical, and biological properties under in situ pressure, temperature, and restored effective stress conditions. Measurement results, combined with index-property data and analytical physics-based models, provide unique insight into hydrate-bearing sediments in situ. Tested cores contain some silty-sands, but are predominantly sandy- and clayey-silts. Hydrate saturations Sh range from 0.15 to 0.74, with significant concentrations in the silty-sands. Wave velocity and flexible-wall permeameter measurements on never-depressurized pressure-core sediments suggest hydrates in the coarser-grained zones, the silty-sands where Sh exceeds 0.4, contribute to soil-skeletal stability and are load-bearing. In the sandy- and clayey-silts, where Sh < 0.4, the state of effective stress and stress history are significant factors determining sediment stiffness. Controlled depressurization tests show that hydrate dissociation occurs too quickly to maintain thermodynamic equilibrium, and pressure–temperature conditions track the hydrate stability boundary in pure-water, rather than that in seawater, in spite of both the in situ pore water and the water used to maintain specimen pore pressure prior to dissociation being saline. Hydrate dissociation accompanied with fines migration caused up to 2.4% vertical strain contraction. The first-ever direct shear measurements on never-depressurized pressure-core specimens show hydrate-bearing sediments have higher sediment strength and peak friction angle than post-dissociation sediments, but the residual friction angle remains the same in both cases. Permeability measurements made before and after hydrate dissociation demonstrate that water permeability increases after dissociation, but the gain is limited by the transition from hydrate saturation

Risk factors of methane hydrate resource development in the concentrated zones distributed in the eastern Nankai Trough

Science.gov (United States)

Yamamoto, K.; Nagakubo, S.

2009-04-01

Some environmental and safety concerns on the offshore methane hydrate development have been raised, but the ground of such allegations are sometime not fully reasonable. The risks of methane hydrate resource development to environment and safety should be discussed upon methane hydrate occurrences condition, the production methods, and the designs of production system, under comprehensively scientific manners. In the Phase 1 of the Methane Hydrate Exploitation Program in Japan (FY2001-2008), the Research Consortium for Methane Hydrate Resources in Japan (MH21 Research Consortium) found methane hydrate concentrated zones in the eastern Nankai Trough that are potential prospects for resource development. The concentrated zones are consisted of turbidite-derived sandy sediments and hydrate crystals in pore spaces of sand grains (pore-filling type structure). The MH21 Research Consortium proposed the depressurization method as prime technique due to its efficiency of gas production in such concentrated zones, and has tried to develop conceptual designs of production systems based on the information of existing devices and facilities. Under the condition and circumstances described above, the authors tried to extract and evaluate some risk factors concerning methane hydrate development using depressurization in the area. Leakage of methane gas, that is less harmful substance to ecosystem than heavier hydrocarbons, from production system can be one possible risk. However, in the case of gas production through wellbore, even if catastrophic damages happen in the subsea production system during gas production, the leakages do not continue because the borehole could be filled by seawater and depressurization is stopped immediately. Another possible risk is a leakage of produced gas through seafloor. If methane hydrate production makes high pressure or temperature zones in sediments, the risk should be considered. However, depressurization method makes opposite condition

Preparing for the Future Nankai Trough Tsunami: A Data Assimilation and Inversion Analysis From Various Observational Systems

Science.gov (United States)

Mulia, Iyan E.; Inazu, Daisuke; Waseda, Takuji; Gusman, Aditya Riadi

2017-10-01

The future Nankai Trough tsunami is one of the imminent threats to the Japanese coastal communities that could potentially cause a catastrophic event. As a part of the countermeasure efforts for such an occurrence, this study analyzes the efficacy of combining tsunami data assimilation (DA) and waveform inversion (WI). The DA is used to continuously refine a wavefield model whereas the WI is used to estimate the tsunami source. We consider a future scenario of the Nankai Trough tsunami recorded at various observational systems, including ocean bottom pressure (OBP) gauges, global positioning system (GPS) buoys, and ship height positioning data. Since most of the OBP gauges are located inside the source region, the recorded tsunami signals exhibit significant offsets from surface measurements due to coseismic seafloor deformation effects. Such biased data are not applicable to the standard DA, but can be taken into account in the WI. On the other hand, the use of WI for the ship data may not be practical because a considerably large precomputed tsunami database is needed to cope with the spontaneous ship locations. The DA is more suitable for such an observational system as it can be executed sequentially in time and does not require precomputed scenarios. Therefore, the combined approach of DA and WI allows us to concurrently make use of all observational resources. Additionally, we introduce a bias correction scheme for the OBP data to improve the accuracy, and an adaptive thinning of observations to determine the efficient number of observations.

Sedimentological Properties of Natural Gas Hydrates-Bearing Sands in the Nankai Trough and Mallik Areas

Science.gov (United States)

Uchida, T.; Tsuji, T.; Waseda, A.

2009-12-01

The Nankai Trough parallels the Japanese Island, where extensive BSRs have been interpreted from seismic reflection records. High resolution seismic surveys have definitely indicated gas hydrate distributions, and drilling the MITI Nankai Trough wells in 2000 and the METI Tokai-oki to Kumano-nada wells in 2004 have revealed subsurface gas hydrate in the eastern part of Nankai Trough. In 1998 and 2002 Mallik wells were drilled at Mackenzie Delta in the Canadian Arctic that also clarified the characteristics of gas hydrate-dominant sandy layers at depths from 890 to 1110 m beneath the permafrost zone. During the field operations, the LWD and wire-line well log data were continuously obtained and plenty of gas hydrate-bearing sand cores were recovered. Subsequence sedimentological and geochemical analyses performed on those core samples revealed the crucial geologic controls on the formation and preservation of natural gas hydrate in sediments. Pore-space gas hydrates reside in sandy sediments mostly filling intergranular porosity. Pore waters chloride anomalies, core temperature depression and core observations on visible gas hydrates confirm the presence of pore-space gas hydrates within moderate to thick sandy layers, typically 10 cm to a meter thick. Sediment porosities and pore-size distributions were obtained by mercury porosimetry, which indicate that porosities of gas hydrate-bearing sandy strata are approximately 45 %. According to grain size distribution curves, gas hydrate is dominant in fine- to very fine-grained sandy strata. Gas hydrate saturations are typically up to 80 % in pore volume throughout most of the hydrate-dominant sandy layers, which are estimated by well log analyses as well as pore water chloride anomalies. It is necessary for investigating subsurface fluid flow behaviors to evaluate both porosity and permeability of gas hydrate-bearing sandy sediments, and the measurements of water permeability for them indicated that highly saturated

Evidence for chaotic fault interactions in the seismicity of the San Andreas fault and Nankai trough

Science.gov (United States)

Huang, Jie; Turcotte, D. L.

1990-01-01

The dynamical behavior introduced by fault interactions is examined here using a simple spring-loaded, slider-block model with velocity-weakening friction. The model consists of two slider blocks coupled to each other and to a constant-velocity driver by elastic springs. For an asymmetric system in which the frictional forces on the two blocks are not equal, the solutions exhibit chaotic behavior. The system's behavior over a range of parameter values seems to be generally analogous to that of weakly coupled segments of an active fault. Similarities between the model simulations and observed patterns of seismicity on the south central San Andreas fault in California and in the Nankai trough along the coast of southwestern Japan.

Paleographical, Bathymetric and Numerical Investigations for a Tsunami Possibly Caused by Submarine Mass Failure in the Nankai Trough, Japan

Science.gov (United States)

Baba, T.; Ashi, J.; Kanamatsu, T.; Imai, K.; Yamashita, K.

2017-12-01

"SHINCHO-KI" is an ancient document that records tsunami damages caused by the 1512 Eisho earthquake, the 1605 Keicho earthquake, the 1707 Hoei earthquake and the 1854 Ansei-Nankai earthquake in Shishikui, where is located along the coast of the southeastern part of Shikoku, facing to the Nankai trough. According to SHINCHO-KI, 3700 people were dead in Shishikui by the tsunami during the 1512 Eisho earthquake. However, no evidence was found for the occurrence of the 1512 Eisho earthquake except for SHINCHO-KI, while the other earthquakes were recorded in many ancient documents in the southwestern Japan. To investigate the source mechanism of the 1512 Eisho earthquake, we carefully read a bathymetric chart and found a scarp with a height of about 400 m and a width of about 6000 m at a position about 24 km offshore in the southeastern direction from Shishikui. We also carried out a survey by using a deep-towed sub-bottom profiler (SBP) on ROV NSS during the R/V Hakuho-maru KH-16-5 cruise. The result shows detailed structures possibly caused by a recent landslide. The vertical displacement of the strata was measured to be about 50 m. By considering these results, we simulated the 1512 Eisho tsunami generated by a submarine mass failure. The topographic data in Shishikui which is needed in the calculation was made from the present data. But we removed the artificial structures such as wave breakers and altered coastlines by referring to old map images. In the numerical simulation, the initial sea surface deformation was obtained by the method proposed by Watts et al. (2005), and the tsunami propagation was calculated by solving the nonlinear shallow water equations with dispersive (Boussinesq) term on a finite difference scheme. We solved the advection terms by using the third-order upwind difference to avoid artificial viscosity. The numerical simulation estimated the maximum tsunami height of about 6m and moderate inundation on land in Shishikui by the 1512 Eisho

Estimation of interplate coupling along Nankai trough considering the block motion model based on onland GNSS and seafloor GPS/A observation data using MCMC method

Science.gov (United States)

Kimura, H.; Ito, T.; Tadokoro, K.

2017-12-01

Introduction In southwest Japan, Philippine sea plate is subducting under the overriding plate such as Amurian plate, and mega interplate earthquakes has occurred at about 100 years interval. There is no occurrence of mega interplate earthquakes in southwest Japan, although it has passed about 70 years since the last mega interplate earthquakes: 1944 and 1946 along Nankai trough, meaning that the strain has been accumulated at plate interface. Therefore, it is essential to reveal the interplate coupling more precisely for predicting or understanding the mechanism of next occurring mega interplate earthquake. Recently, seafloor geodetic observation revealed the detailed interplate coupling distribution in expected source region of Nankai trough earthquake (e.g., Yokota et al. [2016]). In this study, we estimated interplate coupling in southwest Japan, considering block motion model and using seafloor geodetic observation data as well as onland GNSS observation data, based on Markov Chain Monte Carlo (MCMC) method. Method Observed crustal deformation is assumed that sum of rigid block motion and elastic deformation due to coupling at block boundaries. We modeled this relationship as a non-linear inverse problem that the unknown parameters are Euler pole of each block and coupling at each subfault, and solved them simultaneously based on MCMC method. Input data we used in this study are 863 onland GNSS observation data and 24 seafloor GPS/A observation data. We made some block division models based on the map of active fault tracing and selected the best model based on Akaike's Information Criterion (AIC): that is consist of 12 blocks. Result We find that the interplate coupling along Nankai trough has heterogeneous spatial distribution, strong at the depth of 0 to 20km at off Tokai region, and 0 to 30km at off Shikoku region. Moreover, we find that observed crustal deformation at off Tokai region is well explained by elastic deformation due to subducting Izu Micro

Biogenic Methane Generation Potential in the Eastern Nankai Trough, Japan: Effect of Reaction Temperature and Total Organic Carbon

Science.gov (United States)

Aung, T. T.; Fujii, T.; Amo, M.; Suzuki, K.

2017-12-01

Understanding potential of methane flux from the Pleistocene fore-arc basin filled turbiditic sedimentary formation along the eastern Nankai Trough is important in the quantitative assessment of gas hydrate resources. We considered generated methane could exist in sedimentary basin in the forms of three major components, and those are methane in methane hydrate, free gas and methane dissolved in water. Generation of biomethane strongly depends on microbe activity and microbes in turn survive in diverse range of temperature, salinity and pH. This study aims to understand effect of reaction temperature and total organic carbon on generation of biomethane and its components. Biomarker analysis and cultural experiment results of the core samples from the eastern Nankai Trough reveal that methane generation rate gets peak at various temperature ranging12.5°to 35°. Simulation study of biomethane generation was made using commercial basin scale simulator, PetroMod, with different reaction temperature and total organic carbon to predict how these effect on generation of biomethane. Reaction model is set by Gaussian distribution with constant hydrogen index and standard deviation of 1. Series of simulation cases with peak reaction temperature ranging 12.5°to 35° and total organic carbon of 0.6% to 3% were conducted and analyzed. Simulation results show that linear decrease in generation potential while increasing reaction temperature. But decreasing amount becomes larger in the model with higher total organic carbon. At higher reaction temperatures, >30°, extremely low generation potential was found. This is due to the fact that the source formation modeled is less than 1 km in thickness and most of formation do not reach temperature more than 30°. In terms of the components, methane in methane hydrate and free methane increase with increasing TOC. Drastic increase in free methane was observed in the model with 3% of TOC. Methane amount dissolved in water shows almost

LWD lithostratigraphy, physical properties and correlations across tectonic domains at the NanTroSEIZE drilling transect, Nankai Trough subduction zone, Japan

Science.gov (United States)

Tudge, J.; Webb, S. I.; Tobin, H. J.

2013-12-01

Since 2007 the Nankai Trough Seismogenic Zone Experiment (NanTroSEIZE) has drilled a total of 15 sites across the Nankai Trough subduction zone, including two sites on the incoming sediments of the Philippine Sea plate (PSP). Logging-while-drilling (LWD) data was acquired at 11 of these sites encompassing the forearc Kumano Basin, upper accretionary prism, toe region and input sites. Each of these tectonic domains is investigated for changes in physical properties and LWD characteristics, and this work fully integrates a large data set acquired over multiple years and IODP expeditions, most recently Expedition 338. Using the available logging-while-drilling data, primarily consisting of gamma ray, resistivity and sonic velocity, a log-based lithostratigraphy is developed at each site and integrated with the core, across the entire NanTroSEIZE transect. In addition to simple LWD characterization, the use of Iterative Non-hierarchical Cluster Analysis (INCA) on the sites with the full suite of LWD data clearly differentiates the unaltered forearc and slope basin sediments from the deformed sediments of the accretionary prism, suggesting the LWD is susceptible to the subtle changes in the physical properties between the tectonic domains. This differentiation is used to guide the development of tectonic-domain specific physical properties relationships. One of the most important physical property relationships between is the p-wave velocity and porosity. To fully characterize the character and properties of each tectonic domain we develop new velocity-porosity relationships for each domain found across the NanTroSEIZE transect. This allows the porosity of each domain to be characterized on the seismic scale and the resulting implications for porosity and pore pressure estimates across the plate interface fault zone.

Velocity-porosity relationships for slope apron and accreted sediments in the Nankai Trough Seismogenic Zone Experiment, Integrated Ocean Drilling Program Expedition 315 Site C0001

Science.gov (United States)

Hashimoto, Y.; Tobin, H. J.; Knuth, M.

2010-12-01

In this study, we focused on the porosity and compressional wave velocity of marine sediments to examine the physical properties of the slope apron and the accreted sediments. This approach allows us to identify characteristic variations between sediments being deposited onto the active prism and those deposited on the oceanic plate and then carried into the prism during subduction. For this purpose we conducted ultrasonic compressional wave velocity measurements on the obtained core samples with pore pressure control. Site C0001 in the Nankai Trough Seismogenic Zone Experiment transect of the Integrated Ocean Drilling Program is located in the hanging wall of the midslope megasplay thrust fault in the Nankai subduction zone offshore of the Kii peninsula (SW Japan), penetrating an unconformity at ˜200 m depth between slope apron sediments and the underlying accreted sediments. We used samples from Site C0001. Compressional wave velocity from laboratory measurements ranges from ˜1.6 to ˜2.0 km/s at hydrostatic pore pressure conditions estimated from sample depth. The compressional wave velocity-porosity relationship for the slope apron sediments shows a slope almost parallel to the slope for global empirical relationships. In contrast, the velocity-porosity relationship for the accreted sediments shows a slightly steeper slope than that of the slope apron sediments at 0.55 of porosity. This higher slope in the velocity-porosity relationship is found to be characteristic of the accreted sediments. Textural analysis was also conducted to examine the relationship between microstructural texture and acoustic properties. Images from micro-X-ray CT indicated a homogeneous and well-sorted distribution of small pores both in shallow and in deeper sections. Other mechanisms such as lithology, clay fraction, and abnormal fluid pressure were found to be insufficient to explain the higher velocity for accreted sediments. The higher slope in velocity-porosity relationship for

Interaction of Structure and Physical Properties in Accretionary Wedges: Examples from the Cascadia and Nankai Trough Subduction Zones

Science.gov (United States)

Webb, Susanna I.

Subduction zones are capable of producing large, megathrust earthquakes that are sometimes tsunamigenic. Structure and physical properties in the accretionary wedge play a role in how far rupture can propagate and how the wedge deforms coseismically. In this dissertation, I use seismic reflection data and velocity models from the Cascadia subduction zone and logging data from the Nankai Trough, Japan, to interpret structure, link structure to the broader wedge deformation history, and investigate the material properties at depth. I present a full structural interpretation of newly acquired seismic reflection data in the central Cascadia margin, which is characterized by dominantly landward vergent faulting in the outer wedge, a very low wedge taper angle, and a broad, lightly deformed lower slope terrace. Two decollements are active: an upper decollement within the sedimentary section, and a basal decollement at the sediment-basement interface. These interpretations help delineate the spatial extent of decollements and suggest that supra-wedge sedimentation may influence the development of the wedge, including the formation of the lower slope terrace and out of sequence fault activity. I use velocity models from central Cascadia to estimate excess pore fluid pressure and overpressure ratio at depth, which do not exceed 5 MPa and 0.15, respectively. No excess pore pressure is documented in the underthrust sediment section, but modest overpressure is likely present in the incoming sediment section and the footwalls of thrust sheets. The analysis of pore pressure shows that (1) if the base of the wedge is weak, it is due to mechanical properties of the sediments or a relatively thin underthrust layer and (2) the Cascadia wedge is relatively well-drained, and thus potentially strong, which can lead to a low wedge taper angle. In the Nankai Trough, Japan, I reprocessed sonic log data to obtain P-wave and S-wave velocity values and estimate elastic moduli. The logs

Distribution of dehalogenation activity in subseafloor sediments of the Nankai Trough subduction zone.

Science.gov (United States)

Futagami, Taiki; Morono, Yuki; Terada, Takeshi; Kaksonen, Anna H; Inagaki, Fumio

2013-04-19

Halogenated organic matter buried in marine subsurface sediment may serve as a source of electron acceptors for anaerobic respiration of subseafloor microbes. Detection of a diverse array of reductive dehalogenase-homologous (rdhA) genes suggests that subseafloor organohalide-respiring microbial communities may play significant ecological roles in the biogeochemical carbon and halogen cycle in the subseafloor biosphere. We report here the spatial distribution of dehalogenation activity in the Nankai Trough plate-subduction zone of the northwest Pacific off the Kii Peninsula of Japan. Incubation experiments with slurries of sediment collected at various depths and locations showed that degradation of several organohalides tested only occurred in the shallow sedimentary basin, down to 4.7 metres below the seafloor, despite detection of rdhA in the deeper sediments. We studied the phylogenetic diversity of the metabolically active microbes in positive enrichment cultures by extracting RNA, and found that Desulfuromonadales bacteria predominate. In addition, for the isolation of genes involved in the dehalogenation reaction, we performed a substrate-induced gene expression screening on DNA extracted from the enrichment cultures. Diverse DNA fragments were obtained and some of them showed best BLAST hit to known organohalide respirers such as Dehalococcoides, whereas no functionally known dehalogenation-related genes such as rdhA were found, indicating the need to improve the molecular approach to assess functional genes for organohalide respiration.

Distribution and depth of bottom-simulating reflectors in the Nankai subduction margin

Science.gov (United States)

Ohde, Akihiro; Otsuka, Hironori; Kioka, Arata; Ashi, Juichiro

2018-04-01

Surface heat flow has been observed to be highly variable in the Nankai subduction margin. This study presents an investigation of local anomalies in surface heat flows on the undulating seafloor in the Nankai subduction margin. We estimate the heat flows from bottom-simulating reflectors (BSRs) marking the lower boundaries of the methane hydrate stability zone and evaluate topographic effects on heat flow via two-dimensional thermal modeling. BSRs have been used to estimate heat flows based on the known stability characteristics of methane hydrates under low-temperature and high-pressure conditions. First, we generate an extensive map of the distribution and subseafloor depths of the BSRs in the Nankai subduction margin. We confirm that BSRs exist at the toe of the accretionary prism and the trough floor of the offshore Tokai region, where BSRs had previously been thought to be absent. Second, we calculate the BSR-derived heat flow and evaluate the associated errors. We conclude that the total uncertainty of the BSR-derived heat flow should be within 25%, considering allowable ranges in the P-wave velocity, which influences the time-to-depth conversion of the BSR position in seismic images, the resultant geothermal gradient, and thermal resistance. Finally, we model a two-dimensional thermal structure by comparing the temperatures at the observed BSR depths with the calculated temperatures at the same depths. The thermal modeling reveals that most local variations in BSR depth over the undulating seafloor can be explained by topographic effects. Those areas that cannot be explained by topographic effects can be mainly attributed to advective fluid flow, regional rapid sedimentation, or erosion. Our spatial distribution of heat flow data provides indispensable basic data for numerical studies of subduction zone modeling to evaluate margin parallel age dependencies of subducting plates.[Figure not available: see fulltext.

Investigation of mechanical properties of hydrate-bearing pressure core sediments recovered from the Eastern Nankai Trough using transparent acrylic cell triaxial testing system (TACTT-system)

Science.gov (United States)

Yoneda, J.; Masui, A.; Konno, Y.; Jin, Y.; Kida, M.; Suzuki, K.; Nakatsuka, Y.; Tenma, N.; Nagao, J.

2014-12-01

Natural gas hydrate-bearing pressure core sediments have been sheared in compression using a newly developed Transparent Acrylic Cell Triaxial Testing (TACTT) system to investigate the geophysical and geomechanical behavior of sediments recovered from the deep seabed in the Eastern Nankai Trough, the first Japanese offshore production test region. The sediments were recovered by hybrid pressure core system (hybrid PCS) and pressure cores were cut by pressure core analysis tools (PCATs) on board. These pressure cores were transferred to the AIST Hokkaido centre and trimmed by pressure core non-destructive analysis tools (PNATs) for TACTT system which maintained the pressure and temperature conditions within the hydrate stability boundary, through the entire process of core handling from drilling to the end of laboratory testing. An image processing technique was used to capture the motion of sediment in a transparent acrylic cell, and digital photographs were obtained at every 0.1% of vertical strain during the test. Analysis of the optical images showed that sediments with 63% hydrate saturation exhibited brittle failure, although nonhydrate-bearing sediments exhibited ductile failure. In addition, the increase in shear strength with hydrate saturation increase of natural gas hydrate is in agreement with previous data from synthetic gas hydrate. This research was financially supported by the Research Consortium for Methane Hydrate Resources in Japan (MH21 Research Consortium) that carries out Japan's Methane Hydrate R&D Program by the Ministry of Economy, Trade and Industry (METI).

Shallow very-low-frequency earthquakes accompany slow slip events in the Nankai subduction zone.

Science.gov (United States)

Nakano, Masaru; Hori, Takane; Araki, Eiichiro; Kodaira, Shuichi; Ide, Satoshi

2018-03-14

Recent studies of slow earthquakes along plate boundaries have shown that tectonic tremor, low-frequency earthquakes, very-low-frequency events (VLFEs), and slow-slip events (SSEs) often accompany each other and appear to share common source faults. However, the source processes of slow events occurring in the shallow part of plate boundaries are not well known because seismic observations have been limited to land-based stations, which offer poor resolution beneath offshore plate boundaries. Here we use data obtained from seafloor observation networks in the Nankai trough, southwest of Japan, to investigate shallow VLFEs in detail. Coincident with the VLFE activity, signals indicative of shallow SSEs were detected by geodetic observations at seafloor borehole observatories in the same region. We find that the shallow VLFEs and SSEs share common source regions and almost identical time histories of moment release. We conclude that these slow events arise from the same fault slip and that VLFEs represent relatively high-frequency fluctuations of slip during SSEs.

Permeability of sediment cores from methane hydrate deposit in the Eastern Nankai Trough, Japan

Science.gov (United States)

Konno, Y.; Yoneda, J.; Egawa, K.; Ito, T.; Jin, Y.; Kida, M.; Suzuki, K.; Nakatsuka, Y.; Nagao, J.

2013-12-01

Effective and absolute permeability are key parameters for gas production from methane-hydrate-bearing sandy sediments. Effective and/or absolute permeability have been measured using methane-hydrate-bearing sandy cores and clayey and silty cores recovered from Daini Atsumi Knoll in the Eastern Nankai Trough during the 2012 JOGMEC/JAPEX Pressure coring operation. Liquid-nitrogen-immersed cores were prepared by rapid depressurization of pressure cores recovered by a pressure coring system referred to as the Hybrid PCS. Cores were shaped cylindrically on a lathe with spraying of liquid nitrogen to prevent hydrate dissociation. Permeability was measured by a flooding test or a pressure relaxation method under near in-situ pressure and temperature conditions. Measured effective permeability of hydrate-bearing sediments is less than tens of md, which are order of magnitude less than absolute permeability. Absolute permeability of clayey cores is approximately tens of μd, which would perform a sealing function as cap rocks. Permeability reduction due to a swelling effect was observed for a silty core during flooding test of pure water mimicking hydrate-dissociation-water. Swelling effect may cause production formation damage especially at a later stage of gas production from methane hydrate deposits. This study was financially supported by the Research Consortium for Methane Hydrate Resources in Japan (MH21 Research Consortium) that carries out Japan's Methane Hydrate R&D Program conducted by the Ministry of Economy, Trade and Industry (METI).

Gas Hydrate Petroleum System Modeling in western Nankai Trough Area

Science.gov (United States)

Tanaka, M.; Aung, T. T.; Fujii, T.; Wada, N.; Komatsu, Y.

2017-12-01

Since 2003, we have been conducting Gas Hydrate (GH) petroleum system models covering the eastern Nankai Trough, Japan, and results of resource potential from regional model shows good match with the value depicted from seismic and log data. In this year, we have applied this method to explore GH potential in study area. In our study area, GH prospects have been identified with aid of bottom simulating reflector (BSR) and presence of high velocity anomalies above the BSR interpreted based on 3D migration seismic and high density velocity cubes. In order to understand the pathway of biogenic methane from source to GH prospects 1D-2D-3D GH petroleum system models are built and investigated. This study comprises lower Miocene to Pleistocene, deep to shallow marine sedimentary successions of Pliocene and Pleistocene layers overlain the basement. The BSR were interpreted in Pliocene and Pleistocene layers. Based on 6 interpreted sequence boundaries from 3D migration seismic and velocity data, construction of a depth 3D framework model is made and distributed by a conceptual submarine fan depositional facies model derived from seismic facies analysis and referring existing geological report. 1D models are created to analyze lithology sensitivity to temperature and vitrinite data from an exploratory well drilled in the vicinity of study area. The PSM parameters are applied in 2D and 3D modeling and simulation. Existing report of the explanatory well reveals that thermogenic origin are considered to exist. For this reason, simulation scenarios including source formations for both biogenic and thermogenic reaction models are also investigated. Simulation results reveal lower boundary of GH saturation zone at pseudo wells has been simulated with sensitivity of a few tens of meters in comparing with interpreted BSR. From sensitivity analysis, simulated temperature was controlled by different peak generation temperature models and geochemical parameters. Progressive folding

Instrumented Pressure Testing Chamber (IPTC) Characterization of Methane Gas Hydrate-Bearing Pressure Cores Collected from the Methane Production Test Site in the Eastern Nankai Trough, Offshore Japan

Science.gov (United States)

Waite, W. F.; Santamarina, J. C.; Dai, S.; Winters, W. J.; Yoneda, J.; Konno, Y.; Nagao, J.; Suzuki, K.; Fujii, T.; Mason, D. H.; Bergeron, E.

2014-12-01

Pressure cores obtained at the Daini-Atsumi Knoll in the eastern Nankai Trough, the site of the methane hydrate production test completed by the Methane Hydrate Resources in Japan (MH21) project in March 2013, were recovered from ~300 meters beneath the sea floor at close to in situ pressure. Cores were subsequently stored at ~20 MPa and ~5°C, which maintained hydrate in the cores within stability conditions. Pressure core physical properties were measured at 10 MPa and ~6°C, also within the methane hydrate stability field, using the IPTC and other Pressure Core Characterization Tools (PCCTs). Discrete IPTC measurements were carried out in strata ranging from silty sands to clayey silts within the turbidite sequences recovered in the cores. As expected, hydrate saturations were greatest in more permeable coarser-grained layers. Key results include: 1) Where hydrate saturation exceeded 40% in sandy sediments, the gas hydrate binds sediment grains within the matrix. The pressure core analyses yielded nearly in situ mechanical properties despite the absence of effective stress in the IPTC. 2) In adjacent fine-grained sediment (hydrate saturation < 15%), hydrate did not significantly bind the sediment. IPTC results in these locations were consistent with the zero effective-stress limit of comparable measurements made in PCCT devices that are designed to restore the specimen's in situ effective stress. In sand-rich intervals with high gas hydrate saturations, the measured compressional and shear wave velocities suggest that hydrate acts as a homogeneously-distributed, load-bearing member of the bulk sediment. The sands with high gas hydrate saturations were prone to fracturing (brittle failure) during insertion of the cone penetrometer and electrical conductivity probes. Authors would like to express their sincere appreciation to MH21 and the Ministry of Economy, Trade and Industry for permitting this work to be disclosed at the 2014 Fall AGU meeting.

Impacts of tides on tsunami propagation due to potential Nankai Trough earthquakes in the Seto Inland Sea, Japan

Science.gov (United States)

Lee, Han Soo; Shimoyama, Tomohisa; Popinet, Stéphane

2015-10-01

The impacts of tides on extreme tsunami propagation due to potential Nankai Trough earthquakes in the Seto Inland Sea (SIS), Japan, are investigated through numerical experiments. Tsunami experiments are conducted based on five scenarios that consider tides at four different phases, such as flood, high, ebb, and low tides. The probes that were selected arbitrarily in the Bungo and Kii Channels show less significant effects of tides on tsunami heights and the arrival times of the first waves than those that experience large tidal ranges in inner basins and bays of the SIS. For instance, the maximum tsunami height and the arrival time at Toyomaesi differ by more than 0.5 m and nearly 1 h, respectively, depending on the tidal phase. The uncertainties defined in terms of calculated maximum tsunami heights due to tides illustrate that the calculated maximum tsunami heights in the inner SIS with standing tides have much larger uncertainties than those of two channels with propagating tides. Particularly in Harima Nada, the uncertainties due to the impacts of tides are greater than 50% of the tsunami heights without tidal interaction. The results recommend simulate tsunamis together with tides in shallow water environments to reduce the uncertainties involved with tsunami modeling and predictions for tsunami hazards preparedness. This article was corrected on 26 OCT 2015. See the end of the full text for details.

Paleothermal structure of the Nankai inner accretionary wedge estimated from vitrinite reflectance of cuttings

Science.gov (United States)

Fukuchi, Rina; Yamaguchi, Asuka; Yamamoto, Yuzuru; Ashi, Juichiro

2017-08-01

The paleothermal structure and tectonic evolution of an accretionary prism is basic information for understanding subduction zone seismogenesis. To evaluate the entire paleotemperature profile of the Integrated Ocean Drilling Program (IODP) Site C0002 located in the off-Kumano region of the Nankai Trough and penetrate the inner accretionary wedge down to 3058.5 m below the seafloor (mbsf), we performed a vitrinite reflectance analysis for cuttings and core samples during IODP expeditions 338 and 348: Nankai Trough seismogenic zone experiment. Although vitrinite reflectance values (Ro) tend to increase with depth, two reversals of these values suggested the existence of thrust fault zones with sufficient displacements to offset the paleothermal structure. The estimated maximum paleotemperatures are 42-70°C at 1200-1300 mbsf, 44-100°C at 1600-2400 mbsf, and 56-115°C at 2600-3000 mbsf, respectively. These temperatures roughly coincide with estimated modern temperatures; however, at a smaller scale, the reconstructed partial paleogeothermal gradient (˜60-150°C/km) recorded at the hanging- and footwall of the presumed thrust fault zone is higher than the modern geothermal gradient (˜30-40°C/km). This high paleogeothermal gradient was possibly obtained prior to subduction, reflecting the large heat flow of the young Philippine Sea Plate.

Defining Lithological Units by Cuttings, Core and Logging Data at Site C0009A in the Nankai Trough, Japan: IODP Expedition 319

Science.gov (United States)

Efimenko, N.; Schleicher, A. M.; Buchs, D. M.; Buret, C.; Kawabata, K.; Boutt, D. F.; Underwood, M.; Araki, E.; Byrne, T. B.; McNeill, L. C.; Saffer, D. M.; Eguchi, N. O.; Takahashi, K.; Toczko, S.; Scientists, E.

2009-12-01

The use of cuttings as an alternative or addition to core material is broadly debated in on-shore and off-shore drilling expeditions. Expedition 319 is the first IODP based Nankai Trough Seismogenic Zone Experiment (NanTroSEIZE) project using the riser-drilling method to collect cutting and core samples for scientific studies. One major scientific objective for this site was to characterise the lithology and deformation history of the Kumano forearc basin sediments and its underlying units through comparison of (i) cuttings, (ii) core, (iii) measurements while drilling, and (iv) wireline logging data. Cuttings were retrieved from each 5 m intervals from 703.9 to 1604 m, and cores were recovered from 1509.7 to 1593.9 m below sea floor. As core availability was limited, the study of cuttings was a crucial step in improving our understanding of their potential and limits for lithostratigraphical interpretations compared to core. Mineralogical and chemical analysis of cuttings and core, wireline logging data, and gamma ray data from MWD were available to define four lithostratigraphic units. These units are composed of mud and mudstone with coarser silty and sandy interbeds, and volcanic ash/tuff. Consistency between unit boundaries determined from cuttings and those determined from log data is good in terms of depth, with typical mismatches of less than 10m. Three significant problems affecting the preservation of cuttings were (1) mixing of cuttings as they travel from the drill face to the surface, (2) alteration of natural mineral and structure signatures, and (3) possible contamination from natural clay minerals with the polymer/bentonite drill mud. These difficulties can be overcome in part through the analysis of cuttings of similar sizes (1-4 mm), guided by the analyses of bulk cuttings. A more accurate quantitative characterisation of cuttings through the use of digital imaging might improve the description of lithofacies. Although the quality of cuttings is

An Optimal Design for Placements of Tsunami Observing Systems Around the Nankai Trough, Japan

Science.gov (United States)

Mulia, I. E.; Gusman, A. R.; Satake, K.

2017-12-01

Presently, there are numerous tsunami observing systems deployed in several major tsunamigenic regions throughout the world. However, documentations on how and where to optimally place such measurement devices are limited. This study presents a methodological approach to select the best and fewest observation points for the purpose of tsunami source characterizations, particularly in the form of fault slip distributions. We apply the method to design a new tsunami observation network around the Nankai Trough, Japan. In brief, our method can be divided into two stages: initialization and optimization. The initialization stage aims to identify favorable locations of observation points, as well as to determine the initial number of observations. These points are generated based on extrema of an empirical orthogonal function (EOF) spatial modes derived from 11 hypothetical tsunami events in the region. In order to further improve the accuracy, we apply an optimization algorithm called a mesh adaptive direct search (MADS) to remove redundant measurements from the initially generated points by the first stage. A combinatorial search by the MADS will improve the accuracy and reduce the number of observations simultaneously. The EOF analysis of the hypothetical tsunamis using first 2 leading modes with 4 extrema on each mode results in 30 observation points spread along the trench. This is obtained after replacing some clustered points within the radius of 30 km with only one representative. Furthermore, the MADS optimization can improve the accuracy of the EOF-generated points by approximately 10-20% with fewer observations (23 points). Finally, we compare our result with the existing observation points (68 stations) in the region. The result shows that the optimized design with fewer number of observations can produce better source characterizations with approximately 20-60% improvement of accuracies at all the 11 hypothetical cases. It should be note, however, that our

Geological evidence for Holocene earthquakes and tsunamis along the Nankai-Suruga Trough, Japan

Science.gov (United States)

Garrett, Ed; Fujiwara, Osamu; Garrett, Philip; Heyvaert, Vanessa M. A.; Shishikura, Masanobu; Yokoyama, Yusuke; Hubert-Ferrari, Aurélia; Brückner, Helmut; Nakamura, Atsunori; De Batist, Marc

2016-04-01

The Nankai-Suruga Trough, lying immediately south of Japan's densely populated and highly industrialised southern coastline, generates devastating great earthquakes (magnitude > 8). Intense shaking, crustal deformation and tsunami generation accompany these ruptures. Forecasting the hazards associated with future earthquakes along this >700 km long fault requires a comprehensive understanding of past fault behaviour. While the region benefits from a long and detailed historical record, palaeoseismology has the potential to provide a longer-term perspective and additional insights. Here, we summarise the current state of knowledge regarding geological evidence for past earthquakes and tsunamis, incorporating literature originally published in both Japanese and English. This evidence comes from a wide variety of sources, including uplifted marine terraces and biota, marine and lacustrine turbidites, liquefaction features, subsided marshes and tsunami deposits in coastal lakes and lowlands. We enhance available results with new age modelling approaches. While publications describe proposed evidence from > 70 sites, only a limited number provide compelling, well-dated evidence. The best available records allow us to map the most likely rupture zones of eleven earthquakes occurring during the historical period. Our spatiotemporal compilation suggests the AD 1707 earthquake ruptured almost the full length of the subduction zone and that earthquakes in AD 1361 and 684 were predecessors of similar magnitude. Intervening earthquakes were of lesser magnitude, highlighting variability in rupture mode. Recurrence intervals for ruptures of the a single seismic segment range from less than 100 to more than 450 years during the historical period. Over longer timescales, palaeoseismic evidence suggests intervals ranging from 100 to 700 years. However, these figures reflect thresholds of evidence creation and preservation as well as genuine recurrence intervals. At present, we have

Whole genome amplification approach reveals novel polyhydroxyalkanoate synthases (PhaCs) from Japan Trench and Nankai Trough seawater.

Science.gov (United States)

Foong, Choon Pin; Lau, Nyok-Sean; Deguchi, Shigeru; Toyofuku, Takashi; Taylor, Todd D; Sudesh, Kumar; Matsui, Minami

2014-12-24

Special features of the Japanese ocean include its ranges of latitude and depth. This study is the first to examine the diversity of Class I and II PHA synthases (PhaC) in DNA samples from pelagic seawater taken from the Japan Trench and Nankai Trough from a range of depths from 24 m to 5373 m. PhaC is the key enzyme in microorganisms that determines the types of monomer units that are polymerized into polyhydroxyalkanoate (PHA) and thus affects the physicochemical properties of this thermoplastic polymer. Complete putative PhaC sequences were determined via genome walking, and the activities of newly discovered PhaCs were evaluated in a heterologous host. A total of 76 putative phaC PCR fragments were amplified from the whole genome amplified seawater DNA. Of these 55 clones contained conserved PhaC domains and were classified into 20 genetic groups depending on their sequence similarity. Eleven genetic groups have undisclosed PhaC activity based on their distinct phylogenetic lineages from known PHA producers. Three complete DNA coding sequences were determined by IAN-PCR, and one PhaC was able to produce poly(3-hydroxybutyrate) in recombinant Cupriavidus necator PHB-4 (PHB-negative mutant). A new functional PhaC that has close identity to Marinobacter sp. was discovered in this study. Phylogenetic classification for all the phaC genes isolated from uncultured bacteria has revealed that seawater and other environmental resources harbor a great diversity of PhaCs with activities that have not yet been investigated. Functional evaluation of these in silico-based PhaCs via genome walking has provided new insights into the polymerizing ability of these enzymes.

The role of meltwater in high-latitude trough-mouth fan development : the Disko Trough-Mouth Fan, West Greenland.

OpenAIRE

Cofaigh, Colm Ó.; Hogan, Kelly A.; Jennings, Anne E.; Callard, S. Louise; Dowdeswell, Julian A.; Noormets, Riko; Evans, Jeff

2018-01-01

The Disko Trough-Mouth Fan (TMF) is a major submarine sediment fan located along the central west Greenland continental margin offshore of Disko Trough. The location of the TMF at the mouth of a prominent cross-shelf trough indicates that it is a product of repeated glacigenic sediment delivery from former fast-flowing outlets of the Greenland Ice Sheet, including an ancestral Jakobshavn Isbrae, which expanded to the shelf edge during successive glacial cycles. This study focuses on the upper...

Response to long-period seismic waves recorded by broadband seismometer and pore pressure sensor at IODP Site C0002, Nankai Trough

Science.gov (United States)

Kitada, K.; Araki, E.; Kimura, T.; Saffer, D. M.

2013-12-01

Long term in situ monitoring of seismic activity, slow slip event, and pore fluid behavior around mega earthquake zone is important for understanding the processes of earthquake generation and strain accumulation. In order to characterize the response to long-period seismic waves, we compared waveforms and hydroseismograms recorded by broadband seismometer and pore pressure transducers, respectively, which were installed at IODP Site C0002 in the Nankai Trough Kumano Basin. The borehole monitoring system sensor array at Site C0002 is designed to collect multiparameter observations covering a dynamic range of events, including local microearthquakes, low frequency earthquakes, and large-scale earthquakes similar to the Tonankai earthquake. The suite of sensors for the downhole portion of the observatory includes a broadband seismometer (CMG3TBD, Guralp Systems Ltd.) with sampling rate of 100Hz at the depth of 907mbsf, and four pressure ports connected to pressure gauges located at 948mbsf, 917mbsf, 766mbsf, and at the seafloor. The sampling rate of the data logger was set to 1Hz after successful connection to the DONET seafloor cable network for real-time monitoring on 24 Jan 2013. Since then, we processed 12 earthquakes between a moment magnitude of 6.5 to 8.3. In addition to the comparison of long-period surface waves waveform and pressure data, we compared the records with theoretical strain seismograms. The latter were calculated by normal mode summation using the earth model PREM of Dziewonski and Anderson (1981). A Butterworth bandpass filter was applied to the records with cut-off frequencies of 0.003 and 0.1 Hz. Our initial results indicate that the hydroseismograms correspond well with the vertical rather than the horizontal (radial and transverse) components in seismic data. The observed hydroseismogram have a good correlation with the predicted volumetric strain seismogram, especially for the Okhotsk (2013/05/24 14:17UT, Mw8.3, 632km depth), the Chishima

Anomalously high porosity in subduction inputs to the Nankai Trough (SW Japan) potentially caused by volcanic ash and pumice

Science.gov (United States)

Huepers, A.; Ikari, M.; Underwood, M.; Kopf, A.

2013-12-01

At convergent margins, the sedimentary section seaward of the trench on the subducting oceanic lithosphere provides the source material for accretionary prisms and eventually becomes the host rock of the plate boundary megathrust. The mechanical properties of the sediments seaward of the subduction zone have therefore a first order control on subduction zone forearc mechanics and hydrogeology. At the Nankai Trough (SW Japan) the majority of sediment approaching the subduction zone is clay-rich. Scientific drilling expeditions in the framework of the Ocean Drilling Program (ODP) and the Integrated Ocean Drilling Program (IODP) have revealed an anomalous zone of high porosity in a major lithologic unit known as the Upper Shikoku Basin facies (USB), which is associated with elevated volcanic ash content and high amounts of silica in the interstitial water. The existence of the high porosity zone has previously been associated with advanced silica cementation, driven by the dual diagenetic transition of opal-A to opal-CT, and opal-CT to quartz. However, temperature estimates from recent drilling expeditions offshore the Kii peninsula reveal different in situ temperatures at the proposed diagenetic boundary in the Shikoku Basin. Furthermore, laboratory measurements using core samples from the USB show that cohesive strength is not elevated in the high porosity zone, suggesting that a process other than cementation may be responsible. The USB sediment is characterized by abundant volcanic ash and pumice, therefore the high porosity zone in the USB may be closely linked to the mechanical behavior of this phase. We conducted consolidation tests in the range 0.1 to 8 MPa effective vertical stress on artificial ash-smectite and pumice-smectite mixtures, as well as intact and remolded natural samples from the IODP Sites C0011 and C0012 to investigate the role of the volcanic constituent on porosity loss with progressive burial. Our results show that both remolded and intact

The First D/V Chikyu IODP Operations: Successful Logging and Coring During NanTroSEIZE Stage 1 Expeditions

Directory of Open Access Journals (Sweden)

Moe Kyaw Thu

2008-07-01

Full Text Available The Nankai Trough Seismogenic Zone Experiment (NanTroSEIZE is a multi-expedition IODP drilling project aimed at drilling, coring, logging, and instrumenting the seismogenic zone of an active subduction margin , in a region thought to generate megathrust earthquakes of magnitude >8.0 on the moment-magnitude scale (Tobin and Kinoshita, 2006. The Nankai Trough, offshore of the Kii Peninsula, Honshu, Japan (Fig. 1 was chosen as the location for thisproject based on a number of scientific drilling proposals to IODP. These reviewed existing drilling data in the region, the long-term historical and recent record of great earthquakes, the social and societal relevance of the area, and the accessibility of the seismogenic zone to present drilling technology. The first stage of this multi-stage project was intended to accomplish a broad characterization of the shallow geology, geophysics, physical properties, heat flow, and fluid flow in a transect across the downgoing Philippine Sea Plate, the toe of the Nankai accretionary prism, the megasplay fault zone region on the continental slope, and the Kumano Basin that lies between the accretionary prism and the KiiPeninsula, on the continental shelf (Fig. 2.

Nankai Stress History and Implications for an Overpressured Decollement

Science.gov (United States)

Moran, K.; O'Regan, M.

2005-12-01

The Nankai Trough, formed from the subduction of the Shikoku Basin beneath the island arc of southwestern Japan, is a relatively young accretionary complex converging at a rate of ~4 cm/yr [Shipboard Scientific Party, 2001a]. The region was studied during the Deep Sea Drilling Project and on three Ocean Drilling Program (ODP) Legs-131, 190 and 196. Three sites visited during these Legs form a single cross-margin transect (dubbed the Muroto Transect) that traverses the leading edge of the Nankai accretionary prism, from seaward of the deformation front at Site 1173, to close to the deformation front (Site 1174), and landward to the first frontal thrust (Site 808). The decollement, which forms the major boundary between the converging plates, occurs within the Lower Shikoku Basin stratigraphic unit. The ODP sites were drilled and cored to depths below the decollement (Sites 808 and 1174) and the proto-decollement (Site 1173). Here we present consolidation test results [Moran et al., 1993] that are consistent with porosity-depth functions from core and log measurements for the Lower Shikoku Basin sediments, assuming that the decollement is an overpressured seal. At 1173, where a true decollement has not yet formed, moderate fluid overpressures occur that can be fully attributed to high turbiditic sedimentation rates. Forward modeling of this site into the deformation front over a period of ~300 ky shows that the present 1173 porosity-depth function matches the porosity-depth function at 1174. These results suggest that the young decollement on the Muroto Transect at the deformation front and landward is highly overpressured and forms a seal to sediments below that can be classically modeled as a one-dimensional consolidation system.

Report on Radiocarbon Analysis of Surface Sediments from the Fore-Arc Basin of Nankai Trough

National Research Council Canada - National Science Library

Pohlman, John

2004-01-01

.... Radiocarbon analysis of the total organic carbon (TOC) and total inorganic carbon (TIC) on 30 sediment samples from two multicores and six piston cores was performed to investigate the fate of methane carbon in sediment of the Nankal Trough...

Gas in Place Resource Assessment for Concentrated Hydrate Deposits in the Kumano Forearc Basin, Offshore Japan, from NanTroSEIZE and 3D Seismic Data

Science.gov (United States)

Taladay, K.; Boston, B.

2015-12-01

Natural gas hydrates (NGHs) are crystalline inclusion compounds that form within the pore spaces of marine sediments along continental margins worldwide. It has been proposed that these NGH deposits are the largest dynamic reservoir of organic carbon on this planet, yet global estimates for the amount of gas in place (GIP) range across several orders of magnitude. Thus there is a tremendous need for climate scientists and countries seeking energy security to better constrain the amount of GIP locked up in NGHs through the development of rigorous exploration strategies and standardized reservoir characterization methods. This research utilizes NanTroSEIZE drilling data from International Ocean Drilling Program (IODP) Sites C0002 and C0009 to constrain 3D seismic interpretations of the gas hydrate petroleum system in the Kumano Forearc Basin. We investigate the gas source, fluid migration mechanisms and pathways, and the 3D distribution of prospective HCZs. There is empirical and interpretive evidence that deeply sourced fluids charge concentrated NGH deposits just above the base of gas hydrate stability (BGHS) appearing in the seismic data as continuous bottoms simulating reflections (BSRs). These HCZs cover an area of 11 by 18 km, range in thickness between 10 - 80 m with an average thickness of 40 m, and are analogous to the confirmed HCZs at Daini Atsumi Knoll in the eastern Nankai Trough where the first offshore NGH production trial was conducted in 2013. For consistency, we calculated a volumetric GIP estimate using the same method employed by Japan Oil, Gas and Metals National Corporation (JOGMEC) to estimate GIP in the eastern Nankai Trough. Double BSRs are also common throughout the basin, and BGHS modeling along with drilling indicators for gas hydrates beneath the primary BSRs provides compelling evidence that the double BSRs reflect a BGHS for structure-II methane-ethane hydrates beneath a structure-I methane hydrate phase boundary. Additional drilling

Characterization of structures of the Nankai Trough accretionary prism from integrated analyses of LWD log response, resistivity images and clay mineralogy of cuttings: Expedition 338 Site C0002

Science.gov (United States)

Jurado, Maria Jose; Schleicher, Anja

2014-05-01

The objective of our research is a detailed characterization of structures on the basis of LWD oriented images and logs,and clay mineralogy of cuttings from Hole C0002F of the Nankai Trough accretionary prism. Our results show an integrated interpretation of structures derived from borehole images, petrophysical characterization on LWD logs and cuttings mineralogy. The geometry of the structure intersected at Hole C0002F has been characterized by the interpretation of oriented borehole resistivity images acquired during IODP Expedition 338. The characterization of structural features, faults and fracture zones is based on a detailed post-cruise interpretation of bedding and fractures on borehole images and also on the analysis of Logging While Drilling (LWD) log response (gamma radioactivity, resistivity and sonic logs). The interpretation and complete characterization of structures (fractures, fracture zones, fault zones, folds) was achieved after detailed shorebased reprocessing of resistivity images, which allowed to enhance bedding and fracture's imaging for geometry and orientation interpretation. In order to characterize distinctive petrophysical properties based on LWD log response, it could be compared with compositional changes derived from cuttings analyses. Cuttings analyses were used to calibrate and to characterize log response and to verify interpretations in terms of changes in composition and texture at fractures and fault zones defined on borehole images. Cuttings were taken routinely every 5 m during Expedition 338, indicating a clay-dominated lithology of silty claystone with interbeds of weakly consolidated, fine sandstones. The main mineralogical components are clay minerals, quartz, feldspar and calcite. Selected cuttings were taken from areas of interest as defined on LWD logs and images. The clay mineralogy was investigated on the LWD) data allowed us to characterize structural, petrophysical and mineralogical properties at fracture and

Near-trench slip potential of megaquakes evaluated from fault properties and conditions

Science.gov (United States)

Hirono, Tetsuro; Tsuda, Kenichi; Tanikawa, Wataru; Ampuero, Jean-Paul; Shibazaki, Bunichiro; Kinoshita, Masataka; Mori, James J.

2016-01-01

Near-trench slip during large megathrust earthquakes (megaquakes) is an important factor in the generation of destructive tsunamis. We proposed a new approach to assessing the near-trench slip potential quantitatively by integrating laboratory-derived properties of fault materials and simulations of fault weakening and rupture propagation. Although the permeability of the sandy Nankai Trough materials are higher than that of the clayey materials from the Japan Trench, dynamic weakening by thermally pressurized fluid is greater at the Nankai Trough owing to higher friction, although initially overpressured fluid at the Nankai Trough restrains the fault weakening. Dynamic rupture simulations reproduced the large slip near the trench observed in the 2011 Tohoku-oki earthquake and predicted the possibility of a large slip of over 30 m for the impending megaquake at the Nankai Trough. Our integrative approach is applicable globally to subduction zones as a novel tool for the prediction of extreme tsunami-producing near-trench slip. PMID:27321861

Aeolian sand transport over complex intertidal bar-trough beach topography

Science.gov (United States)

Anthony, Edward J.; Ruz, Marie-Hélène; Vanhée, Stéphane

2009-04-01

Aeolian sand transport on macrotidal beaches with complex intertidal bar-trough topography (ridge-and-runnel beaches) was assessed from experiments in northern France that involved measurements of wind speed, saltation, surface moisture contents, and rates of sand trapping across surveyed portions of the upper beach profile. Beaches exhibiting intertidal bars and troughs are much more complex, topographically, than simple reflective or dissipative beaches. Furthermore, the intertidal bar-trough morphology commonly exhibits strong cross-shore variations in the moisture contents of the beach surface and in patterns of bedform development. The results of four 30-minute experiments, conducted along topographically surveyed portions of the upper beach-dune toe profile, show that troughs act as extremely efficient sand interceptors, because of their permanently saturated state, which also inhibits sand mobilisation. Troughs, thus, limit or segment the dry fetch during conditions of intermittent saltation. Flow lines, inferred from the wind profiles, suggest that complex interactions at the boundary layer are generated by the bar-trough topography. Troughs systematically appear to be characterised by air expansion, while bar faces generate ramp wind acceleration for onshore winds, and sometimes immediate downwind deceleration for offshore winds. These effects may also contribute to cross-shore variations in the rates of sand trapping. Finally, a simple conceptual model of effective fetch development, integrating the effects of the spring-neap tidal range and of gross bar-trough morphological variability over time, is proposed for bar-trough beaches. The model highlights the key theme of fetch segmentation induced by cross-shore differentiation in the moisture contents of the beach surface hinged on the complex topography of multiple bars and troughs.

Evidence and mechanism of Hurricane Fran-Induced ocean cooling in the Charleston Trough

Science.gov (United States)

Xie, Lian; Pietrafesa, L. J.; Bohm, E.; Zhang, C.; Li, X.

Evidence of enhanced sea surface cooling during and following the passage of Hurricane Fran in September 1996 over an oceanic depression located on the ocean margin offshore of Charleston, South Carolina (referred to as the Charleston Trough), [Pietrafesa, 1983] is documented. Approximately 4C° of sea surface temperature (SST) reduction within the Charleston Trough following the passage of Hurricane Fran was estimated based on SST imagery from Advanced Very High Resolution Radiometer (AVHRR) on the NOAA-14 polar orbiting satellite. Simulations using a three-dimensional coastal ocean model indicate that the largest SST reduction occurred within the Charleston Trough. This SST reduction can be explained by oceanic mixing due to storm-induced internal inertia-gravity waves.

Rapid sedimentation and overpressure in shallow sediments of the Bering Trough, offshore southern Alaska

Science.gov (United States)

Daigle, Hugh; Worthington, Lindsay L.; Gulick, Sean P. S.; Van Avendonk, Harm J. A.

2017-04-01

Pore pressures in sediments at convergent margins play an important role in driving chemical fluxes and controlling deformation styles and localization. In the Bering Trough offshore Southern Alaska, extreme sedimentation rates over the last 140 kyr as a result of glacial advance/retreats on the continental shelf have resulted in elevated pore fluid pressures in slope sediments overlying the Pamplona Zone fold and thrust belt, the accretionary wedge resulting from subduction of the Yakutat microplate beneath the North American Plate. Based on laboratory experiments and downhole logs acquired at Integrated Ocean Drilling Program Site U1421, we predict that the overpressure in the slope sediments may be as high as 92% of the lithostatic stress. Results of one-dimensional numerical modeling accounting for changes in sedimentation rate over the last 130 kyr predicted overpressures that are consistent with our estimates, suggesting that the overpressure is a direct result of the rapid sedimentation experienced on the Bering shelf and slope. Comparisons with other convergent margins indicate that such rapid sedimentation and high overpressure are anomalous in sediments overlying accretionary wedges. We hypothesize that the shallow overpressure on the Bering shelf/slope has fundamentally altered the deformation style within the Pamplona Zone by suppressing development of faults and may inhibit seismicity by focusing faulting elsewhere or causing deformation on existing faults to be aseismic. These consequences are probably long-lived as it may take several million years for the excess pressure to dissipate.

Structural factors controlling inter-plate coupling and earthquake rupture process

Science.gov (United States)

Kodaira, S.

2007-05-01

Recent availability of a large number of ocean bottom seismographs (OBSs), a large volume of air-gun array and a long streamer cable for academics provide several new findings of lithospheric scale structures in subduction seismogenic zones. JAMSTEC has acquired long-offset seismic data using a super-densely deploy OBS (i.e. 1 - 5 km spacing OBSs along 100 - 500 km long profiles) in the Nankai seismogeinc zone, SW. Japan, since 1999. Long-offset multichannel seismic (MCS) data by a two-ship experiment, as well as conventional 2D MCS data, have been also acquired at a part of the profiles. Some of those profiles have been designed as combined onshore - offshore profiles for imaging a land-ocean transition zone. One of the most striking findings is an image of several scales of subducted seamounts/ridges in the Nankai trough seismogenic zone. We detected the subducted seamount/ridges, which are 50 - 100 km wide, distributing from near trough axis to ~ 40 km deep beneath the Japanese island. From a point of seismogenic process, an important aspect is that those structures are strongly correlated with slip zones of magnitude 8-class earthquakes, i.e.; subducted seamounts/ridge control the rupture propagations. Moreover, the most recent seismic study crossing the segmentation boundary between M=8 class earthquakes detected a high seismic velocity body forming a strongly coupled patch at the segmentation boundary. The numerical simulation incorporating all those structures explained the historic rupture patterns, and shows the occurrence of a giant earthquake along the entire Nankai trough, a distance of over 600 km long (Mw=8.7). The growth processes of a rupture revealed from the simulation are; 1) prior to the giant earthquake, a small slow event (or earthquake) occurs near the segmentation boundary, 2) this accelerates a very slow slip (slower than the plate convergent rate), at the strong patch, which reduces a degree of coupling, 3) then a rupture easily propagates

Preliminary study on tsunami vulnerability assessment in south coast of Korean Peninsula

International Nuclear Information System (INIS)

Min, Byung Il; Suh, Kyung Suk; Lee, Gyumin; Jun, Kyoung Soo

2015-01-01

The potential impact on the coast by the Nankai trough earthquake has been reviewed in 2003 by the Japanese government. However, the magnitude-9.0 earthquake that occurred in March 2011, the Japanese government has decided to re-evaluation the event and extensive studies revealed that the occurrence of a magnitude-9.0 earthquake in the Nankai Trough. In this revealed result, the tsunami waves have been estimated approximately 50% bigger than previous results. A simulation of the tsunami that would be caused by an earthquake in the Nankai Trough was conducted to determine the effect on the Korean coast. The tsunami waves are simulated to propagate southeastward, diffract clockwise south of Kyushu and head for Cheju Island and the southern coast of Korea. The detailed coastal structures are not included in this research because the computational cost. Further simulation studies are underway to take into account coastal structure

Preliminary study on tsunami vulnerability assessment in south coast of Korean Peninsula

Energy Technology Data Exchange (ETDEWEB)

Min, Byung Il; Suh, Kyung Suk [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Lee, Gyumin; Jun, Kyoung Soo [Sungkyunkwan University, Suwon (Korea, Republic of)

2015-05-15

The potential impact on the coast by the Nankai trough earthquake has been reviewed in 2003 by the Japanese government. However, the magnitude-9.0 earthquake that occurred in March 2011, the Japanese government has decided to re-evaluation the event and extensive studies revealed that the occurrence of a magnitude-9.0 earthquake in the Nankai Trough. In this revealed result, the tsunami waves have been estimated approximately 50% bigger than previous results. A simulation of the tsunami that would be caused by an earthquake in the Nankai Trough was conducted to determine the effect on the Korean coast. The tsunami waves are simulated to propagate southeastward, diffract clockwise south of Kyushu and head for Cheju Island and the southern coast of Korea. The detailed coastal structures are not included in this research because the computational cost. Further simulation studies are underway to take into account coastal structure.

Real-time drilling mud gas monitoring for qualitative evaluation of hydrocarbon gas composition during deep sea drilling in the Nankai Trough Kumano Basin.

Science.gov (United States)

Hammerschmidt, Sebastian B; Wiersberg, Thomas; Heuer, Verena B; Wendt, Jenny; Erzinger, Jörg; Kopf, Achim

2014-01-01

Integrated Ocean Drilling Program Expedition 338 was the second scientific expedition with D/V Chikyu during which riser drilling was conducted as part of the Nankai Trough Seismogenic Zone Experiment. Riser drilling enabled sampling and real-time monitoring of drilling mud gas with an onboard scientific drilling mud gas monitoring system ("SciGas"). A second, independent system was provided by Geoservices, a commercial mud logging service. Both systems allowed the determination of (non-) hydrocarbon gas, while the SciGas system also monitored the methane carbon isotope ratio (δ(13)CCH4). The hydrocarbon gas composition was predominated by methane (> 1%), while ethane and propane were up to two orders of magnitude lower. δ(13)CCH4 values suggested an onset of thermogenic gas not earlier than 1600 meter below seafloor. This study aims on evaluating the onboard data and subsequent geological interpretations by conducting shorebased analyses of drilling mud gas samples. During shipboard monitoring of drilling mud gas the SciGas and Geoservices systems recorded up to 8.64% and 16.4% methane, respectively. Ethane and propane concentrations reached up to 0.03 and 0.013%, respectively, in the SciGas system, but 0.09% and 0.23% in the Geoservices data. Shorebased analyses of discrete samples by gas chromatography showed a gas composition with ~0.01 to 1.04% methane, 2 - 18 ppmv ethane, and 2 - 4 ppmv propane. Quadruple mass spectrometry yielded similar results for methane (0.04 to 4.98%). With δD values between -171‰ and -164‰, the stable hydrogen isotopic composition of methane showed little downhole variability. Although the two independent mud gas monitoring systems and shorebased analysis of discrete gas sample yielded different absolute concentrations they all agree well with respect to downhole variations of hydrocarbon gases. The data point to predominantly biogenic methane sources but suggest some contribution from thermogenic sources at depth, probably due

Distribution of shallow very low frequency earthquakes in the eastern Nankai trough influenced by a subducted oceanic ridge: Results from cluster analysis applied to ocean bottom seismographs

Science.gov (United States)

To, A.; Obana, K.; Araki, E.

2016-12-01

The activity of very low frequency earthquakes (VLFEs) in the shallow accretionary prism of the eastern Nankai trough has been observed frequently in the past. In this study, we investigated the distribution of VLFEs that occurred in October 2015, which were recorded by an array of broadband ocean bottom seismometers (BBOBSs) of DONET1 network. The size of the network is much wider (>80 km) compared to previous BBOBS networks that were used for close-in observations of VLFEs; therefore the new dataset provides a broader overview of the VLFE distribution of this region. We first located the detected events using conventional methods such as the envelope correlation method. However, the results seemed to be largely scattered due to noise and the effect of 3D structures that could not be properly handled. Then, we introduced hierarchal clustering analysis, based on measured travel time patterns among stations obtained for each event. The analyses enabled the assessment of relative locations among events. Finally, the locations of event-clusters were estimated, instead of individual events, so that the obtained locations seemed less scattered. The obtained results indicate that the VLFE distribution is strongly influenced by a subducted ridge (Park et al., 2003) that exists beneath the northeastern side of the DONET1 network. Though the VLFEs are distributed from an area near the outer ridge toward the trench axis in the region with a smooth plate boundary, they are clustered at a shallow depth near the outer ridge in the region of the rough plate boundary. The VLFEs are clustered on the landward side of the peak of the subducted ridge; this could be explained by an elevated pore pressure in the region caused by the low-permeability oceanic ridge that may clog the up-dip pathway of the fluid along the decollement zone. The along-strike variation of the stress state, inferred from the VLFE distribution, should be an important factor in assessing the strain release

Trough for piglets

DEFF Research Database (Denmark)

2006-01-01

A trough is disclosed for supplying piglets with mineral supplements in the suckling period. The trough is designed to awaken the piglets' curiosity and thus make them root in the bottom of the trough, where the mineral supplements are dispensed in form of a dry powder mixture, and thus reduce...

Submarine tectonic relief off Enshunada. Enshunadaoki no hendo chikei

Energy Technology Data Exchange (ETDEWEB)

Iwabuchi, Y; Sasahara, N; Hamamoto, F [Maritime Safety Agency, Tokyo (Japan); Yoshioka, S [10th Resional Maritime Safety Headquarters, Kagoshima (Japan); Kondo, T [Maritime Safety School, Kyoto (Japan)

1991-08-15

This paper reports on the results of investigations on the submarine relief structure off the Enshunada (a sea area which is on the south of the Tenryu River mouth and has about 50km east and west and about 100km north and south) using a bathymetric surveying ship equipped with a narrow multibeam echo sounder. The submarine relief structure of this sea area is clarified into the following topographical districts arranged north to south (each extends roughly in the northeast-southwest direction): the Enshu trough and Tenryu submarine canyon upper valley located in the center thereof, ridges represented by No.l and No.2 Tenryu knolls, the ridge and trough zone where minor ridges and troughes appear complicatedly and repeatedly, and the Nankai trough. The paper contains causes of formation of the Tenryu submarine canyon, the Ryuyo submarine canyon which is located in the northwestern slope of No.2 Tenryu knoll and has a distinct shape, oval-shaped domes scattered in the bottom of Nankai trough, etc. and also opinions on landslide topography seen in the ridge and trough zone. 13 refs., 5 figs., 1 tab.

Relationship between the Prediction Accuracy of Tsunami Inundation and Relative Distribution of Tsunami Source and Observation Arrays: A Case Study in Tokyo Bay

Science.gov (United States)

Takagawa, T.

2017-12-01

A rapid and precise tsunami forecast based on offshore monitoring is getting attention to reduce human losses due to devastating tsunami inundation. We developed a forecast method based on the combination of hierarchical Bayesian inversion with pre-computed database and rapid post-computing of tsunami inundation. The method was applied to Tokyo bay to evaluate the efficiency of observation arrays against three tsunamigenic earthquakes. One is a scenario earthquake at Nankai trough and the other two are historic ones of Genroku in 1703 and Enpo in 1677. In general, rich observation array near the tsunami source has an advantage in both accuracy and rapidness of tsunami forecast. To examine the effect of observation time length we used four types of data with the lengths of 5, 10, 20 and 45 minutes after the earthquake occurrences. Prediction accuracy of tsunami inundation was evaluated by the simulated tsunami inundation areas around Tokyo bay due to target earthquakes. The shortest time length of accurate prediction varied with target earthquakes. Here, accurate prediction means the simulated values fall within the 95% credible intervals of prediction. In Enpo earthquake case, 5-minutes observation is enough for accurate prediction for Tokyo bay, but 10-minutes and 45-minutes are needed in the case of Nankai trough and Genroku, respectively. The difference of the shortest time length for accurate prediction shows the strong relationship with the relative distance from the tsunami source and observation arrays. In the Enpo case, offshore tsunami observation points are densely distributed even in the source region. So, accurate prediction can be rapidly achieved within 5 minutes. This precise prediction is useful for early warnings. Even in the worst case of Genroku, where less observation points are available near the source, accurate prediction can be obtained within 45 minutes. This information can be useful to figure out the outline of the hazard in an early

Critically Tapered Wedges and Critical State Soil Mechanics: Porosity-based Pressure Prediction in the Nankai Accretionary Prism.

Science.gov (United States)

Flemings, P. B.; Saffer, D. M.

2016-12-01

We predict pore pressure from porosity measurements at ODP Sites 1174 and 808 in the Nankai Accretionary prism, offshore Japan. For a range of friction angles (5-30 degrees), we estimate that the pore pressure ratio (λ*) ranges from 0.5 to 0.8: the pore pressure supports 50% to 80% of the overburden. Higher friction angles result in higher pressures. For the majority of the scenarios, pressures within the prism parallel the lithostat and are greater than the pressures beneath it. Our results support previous qualitative interpretations at Nankai and elsewhere suggesting that lower porosity above the décollement than below reflects higher mean effective stress there. By coupling a critical state soil model (Modified Cam Clay), which describes porosity as a function of mean and deviator stress, with a stress model that considers the difference in stress states above and below the décollement, we quantitatively show that the prism porosities record significant overpressure despite their lower porosity. As the soil is consumed by the advancing prism, changes in both mean and shear stress drive overpressure generation. Even in the extreme case where only change in mean stress is considered (a vertical end cap model), significant overpressures are generated. The high pressures we predict require an effective friction coefficient (µb') at the décollement of 0.023-0.038. Assuming that the pore pressure at the décollement lies between the values we report for the wedge and the underthrusting sediments, these effective friction coefficients correspond to intrinsic friction coefficients of µb= 0.08-0.38 (f = 4.6 - 21°). These values are comparable to friction coefficients of 0.1-0.4 reported for clay-dominated fault zones in a wide range of settings. By coupling the critical wedge model with an appropriate constitutive model, we present a systematic approach to predict pressure in thrust systems.

Living microbial ecosystems within the active zone of catagenesis: Implications for feeding the deep biosphere

Science.gov (United States)

Horsfield, B.; Schenk, H. J.; Zink, K.; Ondrak, R.; Dieckmann, V.; Kallmeyer, J.; Mangelsdorf, K.; di Primio, R.; Wilkes, H.; Parkes, R. J.; Fry, J.; Cragg, B.

2006-06-01

Earth's largest reactive carbon pool, marine sedimentary organic matter, becomes increasingly recalcitrant during burial, making it almost inaccessible as a substrate for microorganisms, and thereby limiting metabolic activity in the deep biosphere. Because elevated temperature acting over geological time leads to the massive thermal breakdown of the organic matter into volatiles, including petroleum, the question arises whether microorganisms can directly utilize these maturation products as a substrate. While migrated thermogenic fluids are known to sustain microbial consortia in shallow sediments, an in situ coupling of abiotic generation and microbial utilization has not been demonstrated. Here we show, using a combination of basin modelling, kinetic modelling, geomicrobiology and biogeochemistry, that microorganisms inhabit the active generation zone in the Nankai Trough, offshore Japan. Three sites from ODP Leg 190 have been evaluated, namely 1173, 1174 and 1177, drilled in nearly undeformed Quaternary and Tertiary sedimentary sequences seaward of the Nankai Trough itself. Paleotemperatures were reconstructed based on subsidence profiles, compaction modelling, present-day heat flow, downhole temperature measurements and organic maturity parameters. Today's heat flow distribution can be considered mainly conductive, and is extremely high in places, reaching 180 mW/m 2. The kinetic parameters describing total hydrocarbon generation, determined by laboratory pyrolysis experiments, were utilized by the model in order to predict the timing of generation in time and space. The model predicts that the onset of present day generation lies between 300 and 500 m below sea floor (5100-5300 m below mean sea level), depending on well location. In the case of Site 1174, 5-10% conversion has taken place by a present day temperature of ca. 85 °C. Predictions were largely validated by on-site hydrocarbon gas measurements. Viable organisms in the same depth range have been

ON TECTONIC PROBLEMS OF THE OKINAWA TROUGH

Institute of Scientific and Technical Information of China (English)

无

2001-01-01

The Okinawa Trough is a very active tectonic zone at the margin of the Northwest Pacific and is typical of back-arc rifting at the young stage of tectonic evolution. Many scientists from Japan, China, Germany, France, the U.S.A. and Russia have done a lot of geologic and geophysical investigations there. It is well known that the Okinawa Trough is an active back-arc rift with extremely high heat flow, very strong hydrothermal circulation, strong volcanic and magmatic activity, frequent earthquakes, rapid subsidence and rifting, well-developed fault and central graben. But up to now, there are still some important tectonic problems about the Okinawa Trough that require clarification on some aspects such as the type of its crust, its forming time, its tectonic evolution, the distribution of its central grabens, the relationship between its high heat flow and tectonic activity. Based on the data obtained from seismic survey, geomagnetic and gravity measurements, submarine sampling and heat flow measurements in the last 15 years, the author discusses the following tectonic problems about the Okinawa Trough: (1) If the Okinawa Trough develops oceanic crust or not. (2) Is the South Okinawa Trough tectonically more active than the North Okinawa Trough with shallower water and few investigation data on it. (3) The formation time of the Okinawa Trough and its tectonic evolution. The Okinawa Trough has a very thin continental crust. Up to now, there is no evidence of oceanic crust in the Okinawa Trough. The North, Middle and South Okinawa Trough are all very strongly active areas. From 6 Ma B.P., the Okinawa Trough began to form. Since 2 Ma, the Okinawa Trough has been very active.

ON TECTONIC PROBLEMS OF THE OKINAWA TROUGH

Institute of Scientific and Technical Information of China (English)

李乃胜

2001-01-01

The Okinawa Trough is a very active tectonic zone at the margin of the Northwest Pacific and is typical of back-arc rifting at the young stage of tectonic evolution. Many scientists from Japan,China, Germany, France, the U. S.A. and Russia have done a lot of geologic and geophysical investigations there. It is well known that the Okinawa Trough is an active back-arc rift with extremely high heat flow, very strong hydrothermal circulation, strong volcanic and magmatic activity, frequent earthquakes,rapid subsidence and rifting, well-developed fault and central graben. But up to now, there are still some important tectonic problems about the Okinawa Trough that require clarification on some aspects such as the type of its crust, its forming time, its tectonic evolution, the distribution of its central grabens, the relationship between its high heat flow and tectonic activity. Based on the data obtained from seismic sur-vey, geomagnetic and gravity measurements, submarine sampling and heat flow measurements in the last 15 years, the author discusses the following tectonic problems about the Okinawa Trough: (1) If the Okinawa Trough develops oceanic crust or not. (2) Is the South Okinawa Trough tectonically more active than the North Okinawa Trough with shallower water and few investigation data on it. (3) The formation time of the Okinawa Trough and its tectonic evolution. The Okinawa Trough has a very thin continental crust. Up to now, there is no evidence of oceanic crust in the Okinawa Trough. The North, Middle and South Okinawa Trough are all very strongly active areas. From 6 Ma B.P. , the Okinawa Trough began to form. Since 2 Ma, the Okinawa Trough has been very active.

Great earthquakes and slow slip events along the Sagami trough and outline of the Kanto Asperity Project

Science.gov (United States)

Kobayashi, R.; Yamamoto, Y.; Sato, T.; Shishikura, M.; Ito, H.; Shinohara, M.; Kawamura, K.; Shibazaki, B.

2010-12-01

The Kanto region is one of the most densely populated urban areas in the world. Complicated plate configurations are due to T-T-T type triple junction, island arc-island arc collision zone, and very shallow angle between axis of the Sagami trough and subducting direction. Great earthquakes along the Sagami trough have repeatedly occurred. The 1703 Genroku and 1923 (Taisho) Kanto earthquakes caused severe damages in the Tokyo metropolitan area. Intriguingly slow slip events have also repeatedly occurred in an area adjacent to the asperities of the great earthquakes, off Boso peninsula (e.g., Ozawa et al 2007). In the cases of the Nankai and Cascadia subduction zones, slow slip events occur at deeper levels than the asperity, in a transition zone between the asperity and a region of steady slip. In contrast, slow slip events in the Kanto region have occurred at relatively shallow depths, at the same level as the asperity, raising the possibility of friction controlled by different conditions to those (temperature and pressure) encountered at Nankai and Cascadia. We focus on three different types of seismic events occurring repeatedly at the almost same depth of the seismogenic zone along the Sagami trough (5-20 km) (1) The 1923 M~7.9 Taisho earthquake, located in Sagami Bay. Maximum slip is about 6 m, the recurrence interval is 200-400 yr, and the coupling rate is 80-100% (“coupling rates” = “slip amounts during earthquakes or slow-slip events” / [“rate of motion of the Philippine Sea Plate” - “recurrence interval”]) . (2) The 1703 M~8.2 Genroku earthquake, located in Sagami Bay, but also extending to the southern part of Boso Peninsula. Maximum slip is 15-20 m, the recurrence interval is ~2000 yr, and the coupling rate at the southern part of the Boso Peninsula is 10-30%. (3) Boso slow-slip events, located southeast of Boso Peninsula. Maximum slip is 15-20 cm over ~10 days, the recurrence interval is 5-6 yr, and the coupling rate is 70

Regional circulation around Heard and McDonald Islands and through the Fawn Trough, central Kerguelen Plateau

Science.gov (United States)

van Wijk, Esmee M.; Rintoul, Stephen R.; Ronai, Belinda M.; Williams, Guy D.

2010-05-01

The fine-scale circulation around the Heard and McDonald Islands and through the Fawn Trough, Kerguelen Plateau, is described using data from three high-resolution CTD sections, Argo floats and satellite maps of chlorophyll a, sea surface temperature (SST) and absolute sea surface height (SSH). We confirm that the Polar Front (PF) is split into two branches over the Kerguelen Plateau, with the NPF crossing the north-eastern limits of our survey carrying 25 Sv to the southeast. The SPF was associated with a strong eastward-flowing jet carrying 12 Sv of baroclinic transport through the deepest part of Fawn Trough (relative to the bottom). As the section was terminated midway through the trough this estimate is very likely to be a lower bound for the total transport. We demonstrate that the SPF contributes to the Fawn Trough Current identified by previous studies. After exiting the Fawn Trough, the SPF crossed Chun Spur and continued as a strong north-westward flowing jet along the eastern flank of the Kerguelen Plateau before turning offshore between 50°S and 51.5°S. Measured bottom water temperatures suggest a deep water connection between the northern and southern parts of the eastern Kerguelen Plateau indicating that the deep western boundary current continues at least as far north as 50.5°S. Analysis of satellite altimetry derived SSH streamlines demonstrates a southward shift of both the northern and southern branches of the Polar Front from 1994 to 2004. In the direct vicinity of the Heard and McDonald islands, cool waters of southern origin flow along the Heard Island slope and through the Eastern Trough bringing cold Winter Water (WW) onto the plateau. Complex topography funnels flow through canyons, deepens the mixed layer and increases productivity, resulting in this area being the preferred foraging region for a number of satellite-tracked land-based predators.

Solar photovoltaic reflective trough collection structure

Science.gov (United States)

Anderson, Benjamin J.; Sweatt, William C.; Okandan, Murat; Nielson, Gregory N.

2015-11-19

A photovoltaic (PV) solar concentration structure having at least two troughs encapsulated in a rectangular parallelepiped optical plastic structure, with the troughs filled with an optical plastic material, the troughs each having a reflective internal surface and approximately parabolic geometry, and the troughs each including photovoltaic cells situated so that light impinging on the optical plastic material will be concentrated onto the photovoltaic cells. Multiple structures can be connected to provide a solar photovoltaic collection system that provides portable, efficient, low-cost electrical power.

Theoretical study of nuclear physics with strangeness at Nankai University

International Nuclear Information System (INIS)

Ning Pingzhi

2007-01-01

Theoretical study of nuclear physics with strangeness from the nuclear physics group at Nankai university is briefly introduced. Theoretical calculations on hyperon mean free paths in nuclear medium have been done. The other 4 topics in the area of strangeness nuclear physics are the effect of different baryon impurities in nucleus, the heavy flavored baryon hypernuclei, the eta-mesons in nuclear matter and the properties of kaonic nuclei. (authors)

Geophysical identification and geological Implications of the Southern Alaska Magnetic Trough

Science.gov (United States)

Saltus, R.W.; Hudson, T.L.; Wilson, Frederic H.

2003-01-01

The southern Alaska magnetic trough (SAMT) is one of the fundamental, crustal-scale, magnetic features of Alaska. It is readily recognized on 10 km upward-continued aeromagnetic maps of the state. The arcuate SAMT ranges from 30 to 100 km wide and extends in two separate segments along the southern Alaska margin for about 1200 km onshore (from near the Alaska/Canada border at about 60 degrees north latitude to the Bering Sea) and may continue an additional 500 km or more offshore (in the southern Bering Sea). The SAMT is bordered to the south by the southern Alaska magnetic high (SAMH) produced by strongly magnetic crust and to the north by a magnetically quiet zone that reflects weakly magnetic interior Alaska crust. Geophysically, the SAMT is more than just the north-side dipole low associated with the SAMH. Several modes of analysis, including examination of magnetic potential (pseudogravity) and profile modeling, indicate that the source of this magnetic trough is a discrete, crustal-scale body. Geologically, the western portion of the SAMT coincides to a large degree with collapsed Mesozoic Kahiltna flysch basin. This poster presents our geophysical evidence for the extent and geometry of this magnetic feature as well as initial geological synthesis and combined geologic/geophysical modeling to examine the implications of this feature for the broad scale tectonic framework of southern Alaska.

241-AZ-101 pump removal trough analysis

International Nuclear Information System (INIS)

Coverdell, B.L.

1995-01-01

As part of the current Hanford mission of environmental cleanup, various long length equipment must be removed from highly radioactive waste tanks. The removal of equipment will utilize portions of the Equipment Removal System for Project W320 (ERS-W320), specifically the 50 ton hydraulic trailer system. Because the ERS-W320 system was designed to accommodate much heavier equipment it is adequate to support the dead weight of the trough, carriage and related equipment for 241AZ101 pump removal project. However, the ERS-W320 components when combined with the trough and its' related components must also be analyzed for overturning due to wind loads. Two troughs were designed, one for the 20 in. diameter carriage and one for the 36 in. diameter carriage. A proposed 52 in. trough was not designed and, therefore is not included in this document. In order to fit in the ERS-W320 strongback the troughs were design with the same widths. Structurally, the only difference between the two troughs is that more material was removed from the stiffener plates on the 36 in trough. The reduction in stiffener plate material reduces the allowable load. Therefore, only the 36 in. trough was analyzed

Petroleum resources assessment of the Okinawa Trough

Energy Technology Data Exchange (ETDEWEB)

Oh, Jae Ho; Kwak, Young Hoon; Bong, Pil Yoon; Son, Jin Dam; Cheong, Tae Jin; Lee, Ho Young; Ryu, Byung Jae; Son, Byeong Kook; Hwang, In Gul; Kwon, Young Ihn; Lee, Yong Joo; Kim, Hag Ju; Yi, Sung Soog; Park, Kwan Soon; Park, Keun Pil; Shin, Chang Soo; Sunwoo, Don [Korea Inst. of Geology Mining and Materials, Taejon (Korea, Republic of)

1995-12-01

The hydrocarbon potential has been evaluated for the Tertiary strata in the northwestern margin of the Okinawa Trough on the basis of the pale-ontological, petrological, geochemical data from two wells (Nikkan 8-9 and JDZ 7-3), and geophysical data. Abundant marine micro-fossils such as foraminifera, calcareous nannofossils and dinocysts were yielded in the sedimentary section of the above wells. Abundant palynomorphs originated from nearby onshore are also encountered. Based on nannofossils, the bio-stratigraphic zones from NN12 (Amaurolithus tricorniculatus Zone) to NN19 (Pseudoemiliania lacunosa Zone) are established. The sedimentary sequences are divided by local unconformity into Lower and Upper Groups, the ages of which are Late Miocene and Pliocene to Pleistocene, respectively. According to the geochemical analysis results, it is hard to expect a source rock that can generate enough hydrocarbons necessary for migration in the drilled intervals. Even though the thermal maturity reached the oil generation zone in the penetrated intervals, the calculation by the program GENEX of BEICIP shows that the amount of the generated hydrocarbons is not enough for the migration. A good source rock may be expected in the depth deeper than 4300 m horizon. Analysis of over 3300 Line-km of multichannel seismic data integrated with 2 well data serves to detail the structural and stratigraphic evolution of the western margin of the Okinawa Trough, offshore southern part of Korea peninsula. The overall tectonic style is characterized by a series of half-Graben and tilted fault blocks bounded by listric faults. Tectonics of the rift phase have been established on the basis of structural and stratigraphic analyses of depositional sequences and their seismic expressions. The potential hydrocarbon traps associated with titled fault block, fault and roll-over structure exist. (author). 44 refs.

Fabrication of trough-shaped solar collectors

Science.gov (United States)

Schertz, William W.

1978-01-01

There is provided a radiant energy concentration and collection device formed of a one-piece thin-walled plastic substrate including a plurality of nonimaging troughs with certain metallized surfaces of the substrate serving as reflective side walls for each trough. The one-piece plastic substrate is provided with a seating surface at the bottom of each trough which conforms to the shape of an energy receiver to be seated therein.

Strike-slip faults offshore southern Taiwan: implications for the oblique arc-continent collision processes

Science.gov (United States)

Fuh, Shi-Chie; Liu, Char-Shine; Lundberg, Neil; Reed, Donald L.

1997-06-01

Taiwan is the site of present-day oblique arc-continent collision between the Luzon arc of the Philippine Sea plate and the Chinese continental margin. The major structural pattern revealed from marine geophysical studies in the area offshore southern Taiwan is that of a doubly-vergent orogenic belt, bounded by significant zones of thrusting on the west and east of the submarine accretionary wedge. Due to the oblique collision process, strike-slip faults could play an important role in this convergent domain. Topographic lineaments revealed from new digital bathymetry data and seismic reflection profiles confirm the existence of three sets of strike-slip faults in the collision-subduction zone offshore southern Taiwan: the N-S-trending left-lateral strike-slip faults within the Luzon volcanic arc, the NE-SW-trending right-lateral strike-slip faults across the accretionary wedge, and the NNE-SSW-trending left-lateral strike-slip faults lie in the frontal portion of the accretionary wedge. These strike-slip faults overprint pre-existing folds and thrusts and may convert into oblique thrusts or thrusts as the forearc blocks accrete to the mountain belt. A bookshelf rotation model is used to explain the observed geometrical relationships of these strike-slip fault systems. Based on this model, the counter-clockwise rotation of the forearc blocks in the area offshore southern Taiwan could have caused extrusion of the accretionary wedge material into the forearc basin. The originally continuous forearc basin is thus deformed into several closed and separate proto-collisional basins such as the Southern Longitudinal Trough and Taitung Trough. A tectonic evolution model which emphasizes on the development of various structures at different stages of the oblique arc-continent collision for the Taiwan mountain belt is proposed.

Movements of the mid-latitude ionospheric trough

International Nuclear Information System (INIS)

Rodger, A.S.; Pinnock, M.

1982-01-01

A new method for monitoring the position and movement of large ionospheric structures is described. The technique uses data from an ionosonde nominally operating at vertical incidence, but relies on there being present a significant gradient in electron concentration. The position and dynamics of the poleward edge of the mid-latitude trough over Halley Bay, Antarctica (L = 4.2) is investigated using this method. Analyses show that the trough moves rapidly equatorward over Halley Bay in the early evening hours, during geomagnetically active periods. For magnetically quiet periods, the trough is not observed till after midnight, when its equatorward motion is comparatively slow. These results showed marked differences from those predicted from published empirical relationships describing variations in trough position with time, particularly before midnight. Changes in the position of the plasma pause with time, determined from two theoretical models and from observations are compared with these results for the trough. Also, one case study is presented in which there is determination of the positions of both the trough and the plasmapause over a 7 h period. Similarities and differences in their relative positions and movements of the two features are identified and their possible causes are briefly discussed. (author)

Parabolic-trough technology roadmap: A pathway for sustained commercial development and deployment of parabolic-trough technology

International Nuclear Information System (INIS)

David Kearney; Hank Price

1999-01-01

Technology roadmapping is a needs-driven technology planning process to help identify, select, and develop technology alternatives to satisfy a set of market needs. The DOE's Office of Power Technologies' Concentrating Solar Power (CSP) Program recently sponsored a technology roadmapping workshop for parabolic trough technology. The workshop was attended by an impressive cross section of industry and research experts. The goals of the workshop were to evaluate the market potential for trough power projects, develop a better understanding of the current state of the technology, and to develop a conceptual plan for advancing the state of parabolic trough technology. This report documents and extends the roadmap that was conceptually developed during the workshop

Cold seeps and splay faults on Nankai margin

Science.gov (United States)

Henry, P.; Ashi, J.; Tsunogai, U.; Toki, T.; Kuramoto, S.; Kinoshita, M.; Lallemant, S. J.

2003-04-01

Cold seeps (bacterial mats, specific fauna, authigenic carbonates) are common on the Nankai margin and considered as evidence for seepage of methane bearing fluids. Camera and submersible surveys performed over the years have shown that cold seeps are generally associated with active faults. One question is whether part of the fluids expelled originate from the seismogenic zone and migrate along splay faults to the seafloor. The localisation of most cold seeps on the hanging wall of major thrusts may, however, be interpreted in various ways: (a) footwall compaction and diffuse flow (b) fluid channelling along the fault zone at depths and diffuse flow near the seafloor (c) erosion and channelling along permeable strata. In 2002, new observations and sampling were performed with submersible and ROV (1) on major thrusts along the boundary between the Kumano forearc basin domain and the accretionary wedge domain, (2) on a fault affecting the forearc (Kodaiba fault), (3) on mud volcanoes in the Kumano basin. In area (1) tsunami and seismic inversions indicate that the targeted thrusts are in the slip zone of the To-Nankai 1944 earthquakes. In this area, the largest seep zone, continuous over at least 2 km, coincides with the termination of a thrust trace, indicating local fluid channelling along the edge of the fault zone. Kodaiba fault is part of another splay fault system, which has both thrusting and strike-slip components and terminates westward into an en-echelon fold system. Strong seepage activity with abundant carbonates was found on a fold at the fault termination. One mud volcano, rooted in one of the en-echelon fold, has exceptionally high seepage activity compared with the others and thick carbonate crusts. These observations suggest that fluid expulsion along fault zones is most active at fault terminations and may be enhanced during fault initiation. Preliminary geochemical results indicate signatures differ between seep sites and suggests that the two

The study of the focal trough in panoramic radiograph

International Nuclear Information System (INIS)

Park, C. S.; Kim, H. P.

1982-01-01

In the study of the focal trough of panoramic radiograph, using the Moritta company Panex EC a series of 48 exposures were taken with the 6-18 brass pins placed in the holes of the plastic model plate, then evaluated by 4 observers. The author analyzed the focal trough defined by the sharpness criteria and calculated the vertical and horizontal magnification range in the corrected focal trough. The results were as follows; 1. Continuous focal trough was not defined in the anterior region using a very high degree of sharpness. 2. As degree of sharpness used in the analysis became less, focal trough was continuous in the anterior and posterior regions, symmetrized bilaterally, and the widths of the focal trough increased more in the posterior region. 3. As sharpness criteria were reduced, the percentage range of image magnification increased in both vertical and horizontal magnification, and especially the percentage range of horizontal magnification was greater than that of vertical magnification.

Delineation, Characterization and Assessment of Gas-hydrates: Examples from Indian Offshore

Science.gov (United States)

Sain, K.

2017-12-01

Successful test productions in McKenzie delta, Alaska, Nankai Trough and more recently in South China Sea have provided great hopes for production of gas-hydrates in near future, and boosted national programs of many countries including India. It has been imperative to map the prospective zones of gas-hydrates and evaluate their resource potential. Hence, we have adopted a systematic strategy for the delineation, characterization and quantification of gas-hydrates based on seismic traveltime tomography, full-waveform inversion, impedance inversion, attributes computation and rock-physical modeling. The bathymetry, seafloor temperature, total organic carbon content, sediment-thickness, rate of sedimentation, geothermal gradient imply that shallow sediments of Indian deep water are good hosts for occurrences of gas-hydrates. From the analysis of multi-channel seismic (MCS) data, we have identified the Krishna-Godavari (KG), Mahanadi and Andaman basins as prospective for gas-hydrates, and their presence has been validated by drilling and coring of Indian Expeditions-01 and -02. The MCS data also shows BSR-like features in the Cauvery, Kerala-Konkan and Saurashtra basins indicating that gas-hydrates cannot be ruled out from these basins also. We shall present several approaches that have been applied to field seismic and well-log data for the detection, characterization and quantification of gas-hydrates along the Indian margin.

The sedimentation rates in the Okinawa Trough during the Late Quaternary

Institute of Scientific and Technical Information of China (English)

无

2005-01-01

On the basis of accelerator mass spectrometer radiocarbon (AMS 14C) dating, sedimentation rates of 11 cores collected from the northern to southern Okinawa Trough are discussed. The sedimentation rates in the Okinawa Trough roughly range from 11 to 39 cm/ka, and the average is 23.0 cm/ka. China's continental matter is the main sediment source of the middle Okinawa Trough and has important contribution to the northern and southern Okinawa Trough. The sedimentation rates during the marine oxygen isotope (MIS)2 are uniformly higher than those during MIS 1 in the northern and middle Okinawa Trough while they are on the contrary in the southern Okinawa Trough. Sedimentation rates in the Okinawa Trough can be one of the proxies of sediment source and an indicator of cooling events.

Linear magnetic anomalies and tectonic development of the middle Okinawa Trough

Institute of Scientific and Technical Information of China (English)

无

2001-01-01

-By analyzing the magnetic anomalies, the linear magnetic anomalies in the middle Okinawa Trough are identified. It means that the crust along the spreading axis is broken, and new oceanic crust is formed. Geophysical data have revealed that a model of three extensive episodes occurs in the Okinawa Trough, which can be named as "doming episode" from the Middle to Late Miocene (Phase I), the episode from the Pliocence to Early Pleistocene (Phase Ⅱ ), and the recent "spreading episode" (Phase Ⅲ ). The magnetic anomalies in the middle Okinawa Trough are very similar to those found in the middle Red Sea, indicating that the Okinawa Trough is developing towards the "Red Sea stage". Similar to the Red Sea, there are a "main trough" and a "axial trough" in the Okinawa Trough.

Re-evaluation of temperature at the updip limit of locked portion of Nankai megasplay inferred from IODP Site C0002 temperature observatory

Science.gov (United States)

Sugihara, Takamitsu; Kinoshita, Masataka; Araki, Eichiro; Kimura, Toshinori; Kyo, Masanori; Namba, Yasuhiro; Kido, Yukari; Sanada, Yoshinori; Thu, Moe Kyaw

2014-12-01

In 2010, the first long-term borehole monitoring system was deployed at approximately 900 m below the sea floor (mbsf) and was assumed to be situated above the updip limit of the seismogenic zone in the Nankai Trough off Kumano (Site C0002). Four temperature records show that the effect of drilling diminished in less than 2 years. Based on in situ temperatures and thermal conductivities measured on core samples, the temperature measurements and heat flow at 900 mbsf are estimated to be 37.9°C and 56 ± 1 mW/m2, respectively. This heat flow value is in excellent agreement with that from the shallow borehole temperature corrected for rapid sedimentation in the Kumano Basin. We use these values in the present study to extrapolate the temperature below 900 mbsf for a megasplay fault at approximately 5,200 mbsf and a plate boundary fault at approximately 7,000 mbsf. To extrapolate the temperature downward, we use logging-while-drilling (LWD) bit resistivity data as a proxy for porosity and estimate thermal conductivity from this porosity using a geometrical mean model. The one-dimensional (1-D) thermal conduction model used for the extrapolation includes radioactive heat and frictional heat production at the plate boundary fault. The estimated temperature at the megasplay ranges from 132°C to 149°C, depending on the assumed thermal conductivity and radioactive heat production values. These values are significantly higher, by up to 40°C, than some of previous two-dimensional (2-D) numerical model predictions that can account for the high heat flow seaward of the deformation front, including a hydrothermal circulation within the subducted igneous oceanic crust. However, our results are in good agreement with those of the 2-D model, which does not include the advection cooling effect. The results imply that 2-D geometrical effects as well as the influence of the advective cooling may be critical and should be evaluated more quantitatively. Revision of 2-D simulation by

Distribution of very low frequency earthquakes in the Nankai accretionary prism influenced by a subducting-ridge

Science.gov (United States)

Toh, Akiko; Obana, Koichiro; Araki, Eiichiro

2018-01-01

We investigated the distribution of very low frequency earthquakes (VLFEs) that occurred in the shallow accretionary prism of the eastern Nankai trough during one week of VLFE activity in October 2015. They were recorded very close from the sources by an array of broadband ocean bottom seismometers (BBOBSs) equipped in Dense Oceanfloor Network system for Earthquakes and Tsunamis 1 (DONET1). The locations of VLFEs estimated using a conventional envelope correlation method appeared to have a large scatter, likely due to effects of 3D structures near the seafloor and/or sources that the method could not handle properly. Therefore, we assessed their relative locations by introducing a hierarchal clustering analysis based on patterns of relative peak times of envelopes within the array measured for each VLFE. The results suggest that, in the northeastern side of the network, all the detected VLFEs occur 30-40 km landward of the trench axis, near the intersection of a splay fault with the seafloor. Some likely occurred along the splay fault. On the other hand, many VLFEs occur closer to the trench axis in the southwestern side, likely along the plate boundary, and the VLFE activity in the shallow splay fault appears less intense, compared to the northeastern side. Although this could be a snap-shot of activity that becomes more uniform over longer-term, the obtained distribution can be reasonably explained by the change in shear stresses and pore pressures caused by a subducting-ridge below the northeastern side of DONET1. The change in stress state along the strike of the plate boundary, inferred from the obtained VLFE distribution, should be an important indicator of the strain release pattern and localised variations in the tsunamigenic potential of this region.

Technical Manual for the SAM Physical Trough Model

Energy Technology Data Exchange (ETDEWEB)

Wagner, M. J.; Gilman, P.

2011-06-01

NREL, in conjunction with Sandia National Lab and the U.S Department of Energy, developed the System Advisor Model (SAM) analysis tool for renewable energy system performance and economic analysis. This paper documents the technical background and engineering formulation for one of SAM's two parabolic trough system models in SAM. The Physical Trough model calculates performance relationships based on physical first principles where possible, allowing the modeler to predict electricity production for a wider range of component geometries than is possible in the Empirical Trough model. This document describes the major parabolic trough plant subsystems in detail including the solar field, power block, thermal storage, piping, auxiliary heating, and control systems. This model makes use of both existing subsystem performance modeling approaches, and new approaches developed specifically for SAM.

Vancomycin AUC/MIC and Corresponding Troughs in a Pediatric Population.

Science.gov (United States)

Kishk, Omayma A; Lardieri, Allison B; Heil, Emily L; Morgan, Jill A

2017-01-01

Adult guidelines suggest an area under the curve/minimum inhibitory concentration (AUC/MIC) > 400 corresponds to a vancomycin trough serum concentration of 15 to 20 mg/L for methicillin-resistant Staphylococcus aureus infections, but obtaining these troughs in children are difficult. The primary objective of this study was to assess the likelihood that 15 mg/kg of vancomycin every 6 hours in a child achieves an AUC/MIC > 400. This retrospective chart review included pediatric patients >2 months to AUCs were calculated four times using three pharmacokinetic methods. A total of 36 patients with 99 vancomycin trough serum concentrations were assessed. Baseline characteristics were similar between groups. For troughs in group 1 (n = 55), the probability of achieving an AUC/MIC > 400 ranged from 16.4% to 90.9% with a median trough concentration of 11.4 mg/L, while in group 2 (n = 44) the probability of achieving AUC/MIC > 400 ranged from 15.9% to 54.5% with mean trough concentration of 9.2 mg/L. The AUC/MICs were not similar between the different pharmacokinetic methods used; however, a trapezoidal equation (Method A) yielded the highest correlation coefficient (r 2 = 0.59). When dosing every 6 hours, an AUC/MIC of 400 correlated to a trough serum concentration of 11 mg/L. The probability of achieving an AUC/MIC > 400 using only a trough serum concentration and an MIC with patients receiving 15 mg/kg every 6 hours is variable based on the method used to calculate the AUC. An AUC/MIC of 400 in children correlated to a trough concentration of 11 mg/L using a trapezoidal Method to calculate AUC.

The F-region trough: seasonal morphology and relation to interplanetary magnetic field

Directory of Open Access Journals (Sweden)

M. Voiculescu

2006-03-01

Full Text Available We present here the results of a statistical study of the ionospheric trough observed in 2003 by means of satellite tomography. We focus on the seasonal morphology of the trough occurrence and investigate the trough latitude, width and the horizontal gradients at the edges, at different magnetic local times, as well as their relations to geomagnetic activity and the interplanetary magnetic field. A seasonal effect is noticed in the diurnal variation of the trough latitude, indicating that summer clearly differs from the other seasons. In winter the troughs seem to follow the solar terminator. The width of the trough has a diurnal variation and it depends on the season, as well. The broadest troughs are observed in winter and the narrowest ones in summer. A discontinuity in the diurnal variation of the trough latitude is observed before noon. It is suggested that this is an indication of a difference between the generation mechanisms of morningside and eveningside troughs. The density gradients at the edges have a complex dependence on the latitude of the trough and on geomagnetic activity. The photoionization and the auroral precipitation are competing in the formation of the trough walls at different magnetic local times. An important finding is that the interplanetary magnetic field plays a role in the occurrence of the trough at different levels of geomagnetic activity. This is probably associated with the topology of the polar cap convection pattern, which depends on the directions of the IMF components By and Bz.

The F-region trough: seasonal morphology and relation to interplanetary magnetic field

Directory of Open Access Journals (Sweden)

M. Voiculescu

2006-03-01

Full Text Available We present here the results of a statistical study of the ionospheric trough observed in 2003 by means of satellite tomography. We focus on the seasonal morphology of the trough occurrence and investigate the trough latitude, width and the horizontal gradients at the edges, at different magnetic local times, as well as their relations to geomagnetic activity and the interplanetary magnetic field. A seasonal effect is noticed in the diurnal variation of the trough latitude, indicating that summer clearly differs from the other seasons. In winter the troughs seem to follow the solar terminator. The width of the trough has a diurnal variation and it depends on the season, as well. The broadest troughs are observed in winter and the narrowest ones in summer. A discontinuity in the diurnal variation of the trough latitude is observed before noon. It is suggested that this is an indication of a difference between the generation mechanisms of morningside and eveningside troughs. The density gradients at the edges have a complex dependence on the latitude of the trough and on geomagnetic activity. The photoionization and the auroral precipitation are competing in the formation of the trough walls at different magnetic local times. An important finding is that the interplanetary magnetic field plays a role in the occurrence of the trough at different levels of geomagnetic activity. This is probably associated with the topology of the polar cap convection pattern, which depends on the directions of the IMF components B_y and B_z.

Accessing offshoring advantages

DEFF Research Database (Denmark)

Mykhaylenko, Alona; Motika, Agnes; Wæhrens, Brian Vejrum

2015-01-01

. Assuming that different levels of synergy may exist between particular offshoring strategic decisions (choosing offshore outsourcing or captive offshoring and the type of function) and different offshoring advantages, this work advocates that the actual fact of realization of certain offshoring advantages...

Mechanical behavior in the Nankai inner accretionary prism, IODP Site C0002

Science.gov (United States)

Valdez, R. D., II; Saffer, D. M.

2017-12-01

Understanding the processes that control seismogenesis and stress state at subduction zones requires knowledge of fault zone and sediment physical and mechanical properties. As part of the International Ocean Discovery Program (IODP) Nankai Trough Seismogenic Zone Experiment (NanTroSEIZE), Expedition 348 drilled into the Kumano forearc basin and underlying inner accretionary prism at Site C0002, located 35 km landward of the trench. One primary objective was to sample and characterize the mechanical behavior of the inner accretionary prism. Here we report on the frictional and unconfined compressive strength (UCS) of mudstone samples and a clay-rich shear zone recovered from 2182-2209 meters below sea floor (mbsf), determined from triaxial deformation tests at confining pressures from 1 to 7 MPa (UCS measurements on mudstones) and 36 MPa (strength of fault zone). Our results show that at a confining pressure of 1 MPa, the wall rock sediments fail at a peak differential stress of 9.1 MPa with a residual stress of 2.8 MPa. A clear peak and evolution to residual strength remains present at 7 MPa, and both the peak and residual strengths of the mudstones increases systematically with confining pressure. At a confining pressure of 36 MPa, the shear zone sediment yields at a differential stress of 25.2 MPa followed by strain-hardening to a maximum stress of 33.1 MPa. The shear zone is frictionally weaker than the surrounding mudstones, with a friction coefficient (μ) of 0.26-0.31, versus µ = 0.45 for the wall rock. The suite of tests defines a UCS for the mudstone of 7.9 MPa. Our friction data suggest that the inner wedge may be weaker than commonly assumed in applications of critical wedge theory to estimate the properties and conditions in accretionary prisms. One key implication is that for a given basal detachment friction coefficient, higher basal pore pressures (or lower wedge pore pressures) would be required to sustain observed taper angles. Additionally, the

Development of real time monitor system displaying seismic waveform data observed at seafloor seismic network, DONET, for disaster management information

Science.gov (United States)

Horikawa, H.; Takaesu, M.; Sueki, K.; Takahashi, N.; Sonoda, A.; Miura, S.; Tsuboi, S.

2014-12-01

Mega-thrust earthquakes are anticipated to occur in the Nankai Trough in southwest Japan. In the source areas, we have deployed seafloor seismic network, DONET (Dense Ocean-floor Network System for Earthquake and Tsunamis), in 2010 in order to monitor seismicity, crustal deformations, and tsunamis. DONET system consists of totally 20 stations, which is composed of six kinds of sensors, including strong-motion seismometers　and quartz pressure gauges. Those stations are densely distributed with an average spatial interval of 15-20 km and cover near the trench axis to coastal areas. Observed data are transferred to a land station through a fiber-optical cable and then to JAMSTEC (Japan Agency for Marine-Earth Science and Technology) data management center through a private network in real time. After 2011 off the Pacific coast of Tohoku Earthquake, each local government close to Nankai Trough try to plan disaster prevention scheme. JAMSTEC will disseminate DONET data combined with research accomplishment so that they will be widely recognized as important earthquake information. In order to open DONET data observed for research to local government, we have developed a web application system, REIS　(Real-time Earthquake Information System). REIS is providing seismic waveform data to some local governments close to Nankai Trough as a pilot study. As soon as operation of DONET is ready, REIS will start full-scale operation. REIS can display seismic waveform data of DONET in real-time, users can select strong motion and pressure data, and configure the options of trace view arrangement, time scale, and amplitude. In addition to real-time monitoring, REIS can display past seismic waveform data and show earthquake epicenters on the map. In this presentation, we briefly introduce DONET system and then show our web　application system. We also discuss our future plans for further developments of REIS.

Federal technology alert. Parabolic-trough solar water heating

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-04-01

Parabolic-trough solar water heating is a well-proven renewable energy technology with considerable potential for application at Federal facilities. For the US, parabolic-trough water-heating systems are most cost effective in the Southwest where direct solar radiation is high. Jails, hospitals, barracks, and other facilities that consistently use large volumes of hot water are particularly good candidates, as are facilities with central plants for district heating. As with any renewable energy or energy efficiency technology requiring significant initial capital investment, the primary condition that will make a parabolic-trough system economically viable is if it is replacing expensive conventional water heating. In combination with absorption cooling systems, parabolic-trough collectors can also be used for air-conditioning. Industrial Solar Technology (IST) of Golden, Colorado, is the sole current manufacturer of parabolic-trough solar water heating systems. IST has an Indefinite Delivery/Indefinite Quantity (IDIQ) contract with the Federal Energy Management Program (FEMP) of the US Department of Energy (DOE) to finance and install parabolic-trough solar water heating on an Energy Savings Performance Contract (ESPC) basis for any Federal facility that requests it and for which it proves viable. For an ESPC project, the facility does not pay for design, capital equipment, or installation. Instead, it pays only for guaranteed energy savings. Preparing and implementing delivery or task orders against the IDIQ is much simpler than the standard procurement process. This Federal Technology Alert (FTA) of the New Technology Demonstration Program is one of a series of guides to renewable energy and new energy-efficient technologies.

Acoustically damped metal oil trough for internal combustion engines. Schallgedaempfte Blech-Oelwanne fuer Brennkraftmaschinen

Energy Technology Data Exchange (ETDEWEB)

Kubis, H.

1991-03-28

The invention refers to an acoustically damped oil trough. As there are strict requirements for reducing the noise emission from internal combustion engines, according to the invention it is proposed that the oil trough should be surrounded by an outer trough, where the outer trough is made of plastic or sheet steel in one or more layers. To avoid noise bridges, the oil trough and outer trough are separated by elastomer elements. The outer trough achieves a reasonably priced increase in sound insulation. It is also possible to backfit an outer trough on engines.

Geochemical constraints on the temperature and timing of carbonate formation and lithification in the Nankai Trough, NanTroSEIZE transect

Science.gov (United States)

Sample, James C.; Torres, Marta E.; Fisher, Andrew; Hong, Wei-Li; Destrigneville, Christine; Defliese, William F.; Tripati, Aradhna E.

2017-02-01

Information about diagenetic processes and temperatures during burial of sediments entering the subduction zone is important for understanding changes in physical properties and seismic behavior during deformation. The geochemistry of authigenic carbonates from accretionary prisms can serve as proxies for conditions during carbonate cementation and resultant lithification. We report results from the Nankai accretionary prism recovered from Integrated Ocean Drilling Program (IODP) sites C0011 and C0012 and we document continued cementation of deep sediment sections prior to subduction. Elemental and isotope data provide evidence for complex mixing of different isotopic reservoirs in pore waters contributing to carbonate chemical signatures. Carbon stable isotope values exhibit a broad range (δ13CV-PDB = +0.1‰ to -22.5‰) that corresponds to different stages of cement formation during burial. Carbonate formation temperatures from carbonate-clumped isotope geochemistry range from 16 °C to 63 °C at Site C0011 and 8.7 °C to 68 °C at Site C0012. The correspondence between the clumped-isotope temperatures and extrapolations of measured in situ temperatures indicate the carbonate is continuing to form at present. Calculated water isotopic compositions are in some cases enriched in 18O relative to measured interstitial waters suggesting a component of inherited seawater or input from clay-bound water. Low oxygen isotope values and the observed Ba/Ca ratios are also consistent with carbonate cementation at depth. Strontium isotopes of interstitial waters (87Sr/86Sr of 0.7059-0.7069) and carbonates (87Sr/86Sr of 0.70715-0.70891) support formation of carbonates from a mixture of strontium reservoirs including current interstitial waters and relic seawater contemporaneous with deposition. Collectively our data reflect mixed sources of dissolved inorganic carbon and cations that include authigenic phases driven by organic carbon and volcanic alteration reactions

Ionospheric trough Model used for Telecommunication Purposes

International Nuclear Information System (INIS)

Rothkaehl, H.; Stanislawska, I.

1999-01-01

The mid-latitude trough is dynamical phenomena influenced the COST 251 area. Modelled parameters in COST 251 project are critically dependent on its location and magnitude. The particular importance to HF propagation assessments involving off-great-circle modes of incorporating a representation of the position of the trough is noted. ITU-R prediction maps (ITU-R, 1997) which are currently used in most international propagation assessments do not include this fact. (author)

Integration of Wave and Offshore Wind Energy in a European Offshore Grid

DEFF Research Database (Denmark)

Chozas, Julia Fernandez; Sørensen, H. C.; Korpås, M.

2010-01-01

of offshore renewable energy sources. According to this, the paper covers i) public and private initiatives for offshore transmission networks, ii) the synergies between the wave and the offshore wind energy sector within an offshore grid, iii) power transmission options for offshore generation and iv...

Parabolic Trough Collector Cost Update for the System Advisor Model (SAM)

Energy Technology Data Exchange (ETDEWEB)

Kurup, Parthiv [National Renewable Energy Lab. (NREL), Golden, CO (United States); Turchi, Craig S. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2015-11-01

This report updates the baseline cost for parabolic trough solar fields in the United States within NREL's System Advisor Model (SAM). SAM, available at no cost at https://sam.nrel.gov/, is a performance and financial model designed to facilitate decision making for people involved in the renewable energy industry. SAM is the primary tool used by NREL and the U.S. Department of Energy (DOE) for estimating the performance and cost of concentrating solar power (CSP) technologies and projects. The study performed a bottom-up build and cost estimate for two state-of-the-art parabolic trough designs -- the SkyTrough and the Ultimate Trough. The SkyTrough analysis estimated the potential installed cost for a solar field of 1500 SCAs as $170/m² +/- $6/m². The investigation found that SkyTrough installed costs were sensitive to factors such as raw aluminum alloy cost and production volume. For example, in the case of the SkyTrough, the installed cost would rise to nearly $210/m² if the aluminum alloy cost was $1.70/lb instead of $1.03/lb. Accordingly, one must be aware of fluctuations in the relevant commodities markets to track system cost over time. The estimated installed cost for the Ultimate Trough was only slightly higher at $178/m², which includes an assembly facility of $11.6 million amortized over the required production volume. Considering the size and overall cost of a 700 SCA Ultimate Trough solar field, two parallel production lines in a fully covered assembly facility, each with the specific torque box, module and mirror jigs, would be justified for a full CSP plant.

New Insight Into the Crustal Structure of the Continental Margin offshore NW Sabah/Borneo

Science.gov (United States)

Barckhausen, U.; Franke, D.; Behain, D.; Meyer, H.

2002-12-01

The continental margin offshore NW Sabah/Borneo (Malaysia) has been investigated with reflection and refraction seismics, magnetics, and gravity during the recent cruise BGR01-POPSCOMS. A total of 4000 km of geophysical profiles has been acquired, thereof 2900 km with reflection seismics. The focus of investigations was on the deep water areas. The margin looks like a typical accretionary margin and was presumably formed during the subduction of a proto South China Sea. Presently, no horizontal movements between the two plates are being observed. Like in major parts of the South China Sea, the area seaward of the Sabah Trough consists of extended continental lithosphere which is characterised by a pattern of rotated fault blocks and half grabens and a carbonate platform of Early Oligocene to Early Miocene age. We found evidence that the continental crust also underlies the Sabah Trough and the adjacent continental slope, a fact that raises many questions about the tectonic history and development of this margin. The tectonic pattern of the Dangerous Grounds' extended continental crust can be traced a long way landward of the Sabah Trough beneath the sedimentary succession of the upper plate. The magnetic anomalies which are dominated by the magnetic signatures of relatively young volcanic features also continue under the continental slope. The sedimentary rocks of the upper plate, in contrast, seem to generate hardly any magnetic anomalies. Based on the new data we propose the following scenario for the development of the NW Sabah continental margin: Seafloor spreading in the present South China Sea started at about 30 Ma in the Late Oligocene. The spreading process separated the Dangerous Grounds area from the SE Asian continent and ceased in late Early Miocene when the oceanic crust of the proto South China Sea was fully subducted in eastward direction along the Borneo-Palawan Trough. During Lower and/or Middle Miocene, Borneo rotated counterclockwise and was

Isotopic feature and uranium dating of the volcanic rocks in the Okinawa Trough

Institute of Scientific and Technical Information of China (English)

无

2006-01-01

Volcanic rocks from the northern and middle Okinawa Trough were dated by uranium-series dating method. Differential fractions using magnetic procedure were designed to separate samples. New report on the ages and isotopic data of rocks in the northern trough (especially black pumice) was discussed. Based on the uranium dates and Sr-Nd isotopic ratio, magmatic evolution process of the Okinawa Trough was noted. Firstly, there have been wide silicic volcanic activities in the Okinawa Trough from late Pleistocene to present, and the volcanic rocks can be divided into three subgroups. Secondly, magma generally came from PREMA source area under the Okinawa Trough. Magmatic evolution in the northern trough was similar to the middle, but different to the south. Finally, volcanic activities indicated that opening of the southern Okinawa Trough did not happen due to the collision between Luson Arc and Eurasian Plate until the early Pleistocene.

3D geometry of a plate boundary fault related to the 2016 Off-Mie earthquake in the Nankai subduction zone, Japan

Science.gov (United States)

Tsuji, Takeshi; Minato, Shohei; Kamei, Rie; Tsuru, Tetsuro; Kimura, Gaku

2017-11-01

We used recent seismic data and advanced techniques to investigate 3D fault geometry over the transition from the partially coupled to the fully coupled plate interface inboard of the Nankai Trough off the Kii Peninsula, Japan. We found that a gently dipping plate boundary décollement with a thick underthrust layer extends beneath the entire Kumano forearc basin. The 1 April 2016 Off-Mie earthquake (Mw6.0) and its aftershocks occurred, where the plate boundary décollement steps down close to the oceanic crust surface. This location also lies beneath the trenchward edge of an older accretionary prism (∼14 Ma) developed along the coast of the Kii peninsula. The strike of the 2016 rupture plane was similar to that of a formerly active splay fault system in the accretionary prism. Thus, the fault planes of the 2016 earthquake and its aftershocks were influenced by the geometry of the plate interface as well as splay faulting. The 2016 earthquake occurred within the rupture area of large interplate earthquakes such as the 1944 Tonankai earthquake (Mw8.1), although the 2016 rupture area was much smaller than that of the 1944 event. Whereas the hypocenter of the 2016 earthquake was around the underplating sequence beneath the younger accretionary prism (∼6 Ma), the 1944 great earthquake hypocenter was close to oceanic crust surface beneath the older accretionary prism. The variation of fault geometry and lithology may influence the degree of coupling along the plate interface, and such coupling variation could hinder slip propagation toward the deeper plate interface in the 2016 event.

Weak Lensing by Galaxy Troughs in DES Science Verification Data

Energy Technology Data Exchange (ETDEWEB)

Gruen, D. [Ludwig Maximilian Univ., Munich (Germany); Max Planck Inst. for Extraterrestrial Physics, Garching (Germany). et al.

2015-09-29

We measure the weak lensing shear around galaxy troughs, i.e. the radial alignment of background galaxies relative to underdensities in projections of the foreground galaxy field over a wide range of redshift in Science Verification data from the Dark Energy Survey. Our detection of the shear signal is highly significant (10σ–15σ for the smallest angular scales) for troughs with the redshift range z ϵ [0.2, 0.5] of the projected galaxy field and angular diameters of 10 arcmin…1°. These measurements probe the connection between the galaxy, matter density, and convergence fields. By assuming galaxies are biased tracers of the matter density with Poissonian noise, we find agreement of our measurements with predictions in a fiducial Λ cold dark matter model. Furthermore, the prediction for the lensing signal on large trough scales is virtually independent of the details of the underlying model for the connection of galaxies and matter. Our comparison of the shear around troughs with that around cylinders with large galaxy counts is consistent with a symmetry between galaxy and matter over- and underdensities. In addition, we measure the two-point angular correlation of troughs with galaxies which, in contrast to the lensing signal, is sensitive to galaxy bias on all scales. Finally, the lensing signal of troughs and their clustering with galaxies is therefore a promising probe of the statistical properties of matter underdensities and their connection to the galaxy field.

Two decades of spatiotemporal variations in subduction zone coupling offshore Japan

Science.gov (United States)

Loveless, John P.; Meade, Brendan J.

2016-02-01

Spatial patterns of interplate coupling on global subduction zones can be used to guide seismic hazard assessment, but estimates of coupling are often constrained using a limited temporal range of geodetic data. Here we analyze ∼19 years of geodetic observations from the GEONET network to assess time-dependent variations in the spatial distribution of coupling on the subduction zones offshore Japan. We divide the position time series into five, ∼3.75-year epochs each decomposed into best-fit velocity, annual periodic signals, coseismic offsets, and postseismic effects following seven major earthquakes. Nominally interseismic velocities are interpreted in terms of a combination of tectonic block motions and earthquake cycle activity. The duration of the inferred postseismic activity covaries with the linear velocity. To address this trade-off, we assume that the nominally interseismic velocity at each station varies minimally from epoch to epoch. This approach is distinct from prior time-series analysis across the earthquake cycle in that position data are not detrended using preseismic velocity, which inherently assumes that interseismic processes are spatially stable through time, but rather the best-fit velocity at each station may vary between epochs. These velocities reveal significant consistency since 1996 in the spatial distribution of coupling on the Nankai subduction zone, with variation limited primarily to the Tokai and Bungo Channel regions, where long-term slow slip events have occurred, and persistently coupled regions coincident with areas that slipped during historic great earthquakes. On the Sagami subduction zone south of Tokyo, we also estimate relatively stable coupling through time. On the Japan-Kuril Trench, we image significant coupling variations owing to effects of the 1994 MW = 7.7 Sanriku-oki, 2003 MW = 8.2 Tokachi-oki, and 2011 MW = 9.0 Tohoku-oki earthquakes. In particular, strong coupling becomes more spatially extensive following

Occupational health offshore

Energy Technology Data Exchange (ETDEWEB)

Crosbie, A.; Davies, F.

2002-07-01

The proceedings contain the 29 papers presented at the conference plus the opening address from the chair of the Health and Safety Commission. The papers in the first session were concerned with policy, strategy and leadership and included a perspective from the offshore industry advisory committee, details of a health planning tool for occupational health assurance and lessons from occupational health management in the offshore sector. The two sessions on the second day dealt with occupational health in the offshore design process and case studies involving physical, chemical and biological agents. Topics included the need to consider occupational health when designing offshore installations, the development of a human factors engineering strategy in petrochemical engineering projects, measuring occupational exposure to hazardous chemicals, implementation of the noise at work regulations, hand arm vibration syndrome and issues with potable water maintenance. The two sessions on the third day were concerned with human factors and psychological health, and well-being and fitness for duty. Topics covered included circadian adaption to shift change in offshore shift workers, managing stress in the offshore environment, the role of employee assistance programmes in organisational stress management, health care and first aid (the revised ACOP), well-being at work, the medical and physical fitness of offshore emergency response rescue team members, the impact of health surveillance and promotion of offshore accident rates, and the implication of safety and heath of the aging of the workforce ion the Norwegian offshore industry.

Offshoring Process

DEFF Research Database (Denmark)

Slepniov, Dmitrij; Sørensen, Brian Vejrum; Katayama, Hiroshi

2011-01-01

The purpose of this chapter is to contribute to the knowledge on how production offshoring and international operations management vary across cultural contexts. The chapter attempts to shed light on how companies approach the process of offshoring in different cultural contexts. In order...... of globalisation. Yet there are clear differences in how offshoring is conducted in Denmark and Japan. The main differences are outlined in a framework and explained employing cultural variables. The findings lead to a number of propositions suggesting that the process of offshoring is not simply a uniform...... technical-rational calculation of the most efficient organisation of activities across national borders, but it is rather specific to the parent companies’ national contexts....

Paleocene Pacific Plate reorganization mirrored in formation of the Suvarov Trough, Manihiki Plateau

Science.gov (United States)

Pietsch, Ricarda; Uenzelmann-Neben, Gabriele

2016-10-01

The Suvarov Trough is a graben structure that deviates from the Danger Islands Troughs within the Manihiki Plateau, a Large Igneous Province (LIP) located in the Central Pacific. New high-resolution seismic reflection data provide evidence that the graben formed in two phases during the Paleocene (65-45 Ma). In a first phase extension occurred in southwestward direction, pulling apart the northern part of the Suvarov Trough and a parallel trending unnamed trough. In a second phase a change of extensional force direction occurred from southwest to west-northwest, forming the southern part of the Suvarov Trough that extends onto the High Plateau. The formation of the Suvarov Trough is accompanied by a series of normal fault systems that apparently formed simultaneously. Comparing the seismic results to existing Pacific paleo strain reconstructions, the timing of increased strain and local deformation direction fits well to our findings. We thus suggest that the multiple strike directions of the Suvarov Trough represent an extensional structure that was caused by the major, stepwise Pacific Plate reorganization during the Paleocene.

Patient-reported non-adherence and immunosuppressant trough levels are associated with rejection after renal transplantation.

Science.gov (United States)

Scheel, Jennifer; Reber, Sandra; Stoessel, Lisa; Waldmann, Elisabeth; Jank, Sabine; Eckardt, Kai-Uwe; Grundmann, Franziska; Vitinius, Frank; de Zwaan, Martina; Bertram, Anna; Erim, Yesim

2017-03-29

Different measures of non-adherence to immunosuppressant (IS) medication have been found to be associated with rejection episodes after successful transplantation. The aim of the current study was to investigate whether graft rejection after renal transplantation is associated with patient-reported IS medication non-adherence and IS trough level variables (IS trough level variability and percentage of sub-therapeutic IS trough levels). Patient-reported non-adherence, IS trough level variability, percentage of sub-therapeutic IS trough levels, and acute biopsy-proven late allograft rejections were assessed in 267 adult renal transplant recipients who were ≥12 months post-transplantation. The rate of rejection was 13.5%. IS trough level variability, percentage of sub-therapeutic IS trough levels as well as patient-reported non-adherence were all significantly and positively associated with rejection, but not with each other. Logistic regression analyses revealed that only the percentage of sub-therapeutic IS trough levels and age at transplantation remained significantly associated with rejection. Particularly, the percentage of sub-therapeutic IS trough levels is associated with acute rejections after kidney transplantation whereas IS trough level variability and patient-reported non-adherence seem to be of subordinate importance. Patient-reported non-adherence and IS trough level variables were not correlated; thus, non-adherence should always be measured in a multi-methodological approach. Further research concerning the best combination of non-adherence measures is needed.

Offshore Investment Funds

Directory of Open Access Journals (Sweden)

Shang-Jin Wei

1999-12-01

Full Text Available Offshore investment funds are alleged to have engaged in trading behavior that is different from their onshore counterparts because they may be subject to less supervision and regulation. In particular, they may trade more intensely. They could also pursue more aggressively certain trading strategies such as positive feedback trading or herding that could contribute to a greater volatility in the market. Using a unique data set, this chapter compares the trading behavior in the Korean stock market between offshore investment funds with their onshore counterparts registered in the US and UK. There are a number of interesting findings. First, there is indeed evidence suggesting that the offshore funds trade more intensely than their onshore counterparts. Second, however, there is no evidence that the offshore funds engage in positive feedback trading. In contrast, there is strong evidence that the funds from the U.S. and U.K. do. Third, while offshore funds do herd, they do so far less than onshore funds in the U.S. or UK. Fourth, offshore funds hold less glamour stocks (e.g. stocks with high P/E in their portfolio than funds in the U.S. or U.K. do. Moreover, flight to glamour stocks during the in-crisis period is less evident in the case of offshore funds. In sum, offshore funds are no especially worrisome monsters.

Seasonal variation and solar activity dependence of the quiet-time ionospheric trough

Science.gov (United States)

Ishida, T.; Ogawa, Y.; Kadokura, A.; Hiraki, Y.; Häggström, I.

2014-08-01

We have conducted a statistical analysis of the ionospheric F region trough, focusing on its seasonal variation and solar activity dependence under geomagnetically quiet and moderate conditions, using plasma parameter data obtained via Common Program 3 observations performed by the European Incoherent Scatter (EISCAT) radar between 1982 and 2011. We have confirmed that there is a major difference in frictional heating between the high- and low-latitude sides of the EISCAT field of view (FOV) at ~73°0'N-60°5'N (geomagnetic latitude) at an altitude of 325 km, which is associated with trough formation. Our statistical results show that the high-latitude and midlatitude troughs occur on the high- and low-latitude sides of the FOV, respectively. Seasonal variations indicate that dissociative recombination accompanied by frictional heating is a main cause of trough formation in sunlit regions. During summer, therefore, the occurrence rate is maintained at 80-90% in the postmidnight high-latitude region owing to frictional heating by eastward return flow. Solar activity dependence on trough formation indicates that field-aligned currents modulate the occurrence rate of the trough during the winter and equinox seasons. In addition, the trough becomes deeper via dissociative recombination caused by an increased ion temperature with F10.7, at least in the equinox and summer seasons but not in winter.

Main ionospheric trough in the daytime sector studied on the basis of vertical sounding data

Energy Technology Data Exchange (ETDEWEB)

Benkova, N.P.; Kozlov, E.F.; Mozhaev, A.M.; Osipov, N.K.; Samorokin, N.I.

1980-09-01

Data for 1969-1973 are used to study the displacement of the main ionospheric trough during daytime magnetic storms. The depth of the trough and electron density gradients on the sides of the trough are determined. The trough is found to move in a southeasterly direction during daytime storms. The results agree with theoretical conclusions that explain the formation of the trough by the collective transport of ionospheric plasma in a sunward direction.

Gas Turbine/Solar Parabolic Trough Hybrid Designs: Preprint

Energy Technology Data Exchange (ETDEWEB)

Turchi, C. S.; Ma, Z.; Erbes, M.

2011-03-01

A strength of parabolic trough concentrating solar power (CSP) plants is the ability to provide reliable power by incorporating either thermal energy storage or backup heat from fossil fuels. Yet these benefits have not been fully realized because thermal energy storage remains expensive at trough operating temperatures and gas usage in CSP plants is less efficient than in dedicated combined cycle plants. For example, while a modern combined cycle plant can achieve an overall efficiency in excess of 55%; auxiliary heaters in a parabolic trough plant convert gas to electricity at below 40%. Thus, one can argue the more effective use of natural gas is in a combined cycle plant, not as backup to a CSP plant. Integrated solar combined cycle (ISCC) systems avoid this pitfall by injecting solar steam into the fossil power cycle; however, these designs are limited to about 10% total solar enhancement. Without reliable, cost-effective energy storage or backup power, renewable sources will struggle to achieve a high penetration in the electric grid. This paper describes a novel gas turbine / parabolic trough hybrid design that combines solar contribution of 57% and higher with gas heat rates that rival that for combined cycle natural gas plants. The design integrates proven solar and fossil technologies, thereby offering high reliability and low financial risk while promoting deployment of solar thermal power.

Whether and What to Offshore?

DEFF Research Database (Denmark)

Jensen, Peter Ørberg; Pedersen, Torben

In this article, we explore the idea that offshoring of services and technical work should be regarded as a dynamic process that evolves over time. Firms gradually move from offshoring of simple, standardized activities towards offshoring of advanced activities when they accumulate experience...... with offshoring, and this type of offshoring comes with an entirely different set of characteristics compared to traditional, cost-seeking offshoring. Based on a unique survey among the total population of firms in the eastern region of Denmark, we analyze some of the dynamics of this process through a model...... that incorporates two different aspects of the process of offshoring. First, we approach the question of whether to offshore and establish a baseline that investigates the determinants of firms’ participation—or lack thereof—in offshoring. Secondly, we approach the question of what to offshore and the subsequent...

Industrial opportunities - offshore

International Nuclear Information System (INIS)

Gerrits, D.J.

1998-01-01

Industrial opportunities available in the Canadian offshore petroleum industry are discussed. Oil has been produced offshore from Nova Scotia since 1992, and offshore from Newfoundland since 1997. Special needs that must be addressed in offshore operations in eastern Canada such as the cold North Atlantic environment, isolation, logistics, safety, and quality assurance, are examined. The most obvious opportunities lie with the designing, building and installing the facilities needed to extract oil and gas from beneath the sea floor and transport it to market. However, there are also opportunities in designing and fabricating clothing, customized food containers and other equipment for offshore needs. Short term opportunities also exist in the decommissioning of depleted production fields and their facilities. One of the greatest obstacles facing new entrants into the offshore oil and gas industry is the lack of a track record. To meet this challenge, the ability to seek out partners to pursue local and international opportunities through joint ventures, strategic alliances and technology sharing partnering arrangements is of great importance. It may be the difference between success and failure. 6 figs

Performance comparison of solar parabolic trough system with glass and film reflector

International Nuclear Information System (INIS)

Xu, Qian; Li, Longlong; Li, Huairui; Huang, Weidong; Li, Yongping

2014-01-01

Highlights: • Solar trough model should consider refractive surface error with glass reflector. • Solar trough system with glass mirror has less efficiency than that with film mirror. • Solar trough system has very low efficiency in a winter day at high latitude. - Abstract: This paper considers the refractive surface error transfer process to present an optical performance model of solar trough system as well as the reflective surface error. We validate the optical model through comparing the calculation results with the experimental data. The optimized design parameters are presented based on the maximization of the annual average net heat efficiency. The results show that maximum relative error of 20% for the optical efficiency may produce if the refractive surface error transfer process is ignored. It indicates that the refractive surface error should be considered in predicting the performance of the solar trough system especially for the glass reflector as well as the reflective surface error. We apply the model to compare the performance of solar parabolic trough system with vacuum tube receiver under two kinds of reflectors, which are glass mirror and film mirror. The results indicate that both parabolic trough systems with a vacuum tube receiver and a north–south axis tracking system are relatively inefficient in winter days, and the net energy output in the winter solstice is less than one sixth of the summer. The net heat efficiency of solar trough system with film mirror is 50% less than that of the system with the glass mirror at noon of the winter solstice and latitude 40 if the design and parameter of the two systems are the same. The results indicate that film reflector is more preferable than glass reflector especially in high latitude if they have the same optical property

From Offshoring to Backshoring

DEFF Research Database (Denmark)

Slepniov, Dmitrij; Madsen, Erik Skov

2015-01-01

The purpose of this paper is to examine the evolution of offshoring over time. The paper employs qualitative methodology and on the basis of two case studies of Danish companies, it develops a framework conceptualizing the stages of offshoring and highlights the factors driving the transition...... between these stages. The framework challenges the linear nature of offshoring and proposes the existence of ‘the pendulum effect’. The pendulum effect suggests that the modes of offshoring (i.e. captive and non-captive) and geographies of offshoring (i.e. home and abroad) are not static; rather...

Tsunami simulations of mega-thrust earthquakes in the Nankai–Tonankai Trough (Japan) based on stochastic rupture scenarios

KAUST Repository

Goda, Katsuichiro

2017-02-23

In this study, earthquake rupture models for future mega-thrust earthquakes in the Nankai–Tonankai subduction zone are developed by incorporating the main characteristics of inverted source models of the 2011 Tohoku earthquake. These scenario ruptures also account for key features of the national tsunami source model for the Nankai–Tonankai earthquake by the Central Disaster Management Council of the Japanese Government. The source models capture a wide range of realistic slip distributions and kinematic rupture processes, reflecting the current best understanding of what may happen due to a future mega-earthquake in the Nankai–Tonankai Trough, and therefore are useful for conducting probabilistic tsunami hazard and risk analysis. A large suite of scenario rupture models is then used to investigate the variability of tsunami effects in coastal areas, such as offshore tsunami wave heights and onshore inundation depths, due to realistic variations in source characteristics. Such investigations are particularly valuable for tsunami hazard mapping and evacuation planning in municipalities along the Nankai–Tonankai coast.

Too much or too little of R&D offshoring : The impact of captive offshoring and contract offshoring on innovation performance

NARCIS (Netherlands)

Steinberg, Philip; Procher, Vivien D.; Urbig, Diemo

2017-01-01

Innovating firms may acquire foreign knowledge and improve their innovation performance by offshoring their R&D activities to their own foreign affiliates (captive offshoring) as well as by contracting out their R&D to external foreign parties (contract offshoring). This study examines the impact of

Safety in offshore engineering an academic course covering safety in offshore wind

NARCIS (Netherlands)

Cerda Salzmann, D.J.

2011-01-01

Offshore projects are known for their challenging conditions, generally leading to high risks. Therefore no offshore project can go without a continuous and extensive assessment on safety issues. The Delft University of Technology is currently developing a course "Safety in Offshore Engineering"

Concurrent immunomodulator therapy is associated with higher adalimumab trough levels during scheduled maintenance therapy.

Science.gov (United States)

Bond, Ashley; Dodd, Susanna; Fisher, Gareth; Skouras, Thomas; Subramanian, Sreedhar

2017-02-01

Combination therapy with infliximab and immunomodulators is superior to monotherapy, resulting in better outcomes and higher trough levels of infliximab. The role of concurrent immunomodulatory therapy on adalimumab trough levels has not been adequately investigated. We evaluated the impact of concomitant immunomodulation on adalimumab trough levels in patients on scheduled maintenance therapy. We conducted a prospective observational, cross-sectional study of all inflammatory bowel disease patients on maintenance therapy who had adalimumab trough levels measured between January 2013 and January 2016. Drug level and anti-drug antibody measurements were performed on sera using a solid phase assay. Pairwise comparison of means was used to compare trough levels in patients with and without concomitant immune modulator therapy. In total, 79 patients were included. Twenty-three patients (29.1%) were on weekly dosing whereas 56 (70.9%) were on alternate weeks. Median adalimumab trough levels were comparable in patients with and without clinical remission (6.8 μg/ml (IQR 5.6-8.1) versus 6.7 μg/ml (IQR 3.9-8.1), respectively. Patients with an elevated faecal calprotectin >250 μg/g had lower adalimumab trough levels (median 6.7, IQR 3.9-8) compared to patients with faecal calprotectin <250 μg/g (median 7.7, IQR 6.1-8.1) though this did not achieve statistical significance (p = .062). Median adalimumab trough levels among patients on concurrent immunomodulators was 7.2 μg/ml (IQR 5.7-8.1) compared to those not on concurrent immunomodulator, 6.1 μg/ml (IQR 2.7-7.7, p = .0297). Adalimumab trough levels were significantly higher in patients on concurrent immunomodulators during maintenance therapy. There was a trend towards a lower adalimumab trough level in patients with elevated calprotectin.

Parabolic Trough Solar Power for Competitive U.S. Markets

International Nuclear Information System (INIS)

Price, Henry W.

1998-01-01

Nine parabolic trough power plants located in the California Mojave Desert represent the only commercial development of large-scale solar power plants to date. Although all nine plants continue to operate today, no new solar power plants have been completed since 1990. Over the last several years, the parabolic trough industry has focused much of its efforts on international market opportunities. Although the power market in developing countries appears to offer a number of opportunities for parabolic trough technologies due to high growth and the availability of special financial incentives for renewables, these markets are also plagued with many difficulties for developers. In recent years, there has been some renewed interest in the U.S. domestic power market as a result of an emerging green market and green pricing incentives. Unfortunately, many of these market opportunities and incentives focus on smaller, more modular technologies (such as photovoltaics or wind power), and as a result they tend to exclude or are of minimum long-term benefit to large-scale concentrating solar power technologies. This paper looks at what is necessary for large-scale parabolic trough solar power plants to compete with state-of-the-art fossil power technology in a competitive U.S. power market

Tracking local control of a parabolic trough collector

International Nuclear Information System (INIS)

Ajona, J.I.; Alberdi, J.; Gamero, E.; Blanco, J.

1992-01-01

In the local control, the sun position related to the trough collector is measured by two photo-resistors. The provided electronic signal is then compared with reference levels in order to get a set of B logical signals which form a byte. This byte and the commands issued by a programmable controller are connected to the inputs of o P.R.O.M. memory which is programmed with the logical equations of the control system. The memory output lines give the control command of the parabolic trough collector motor. (Author)

Offshore in depth

Energy Technology Data Exchange (ETDEWEB)

Ebdon, J F

1968-08-01

The world-wide scope of offshore areas is discussed. Offshore areas of the U.S. and the world are where one of the ''hottest'' hydrocarbon booms--drilling, production, and pipelining--are in action today. Most of the current activity in offshore exploration and drilling is crude oil directed. However, big non-associated natural gas finds have been made. Additionally, for every barrel of crude oil produced, either or both associated natural gas and dissolved natural gas are produced in some varying ratio as casinghead gas. Thus, with worldwide production of some 2.5-million bbl of crude oil per day from offshore areas of Free-World countries, there are vast volumes of casinghead natural gas produced, over and above that produced from non-associated natural gas wells to the seaward of land masses. If offshore gas of any classification is produced in commercial volumes close to onshore population centers, then the possibility of marketing is fairly good. If remote from population centers, it is usually flared or shut-in. The development of gas liquefaction and cryogenic tankers has started, but international ocean traffic in LNG is still in its infancy. Current offshore gas pipelines are described.

Mineralogy and geological significance of hydrothermal deposits from the Okinawa Trough

Science.gov (United States)

Zhang, Xia; Zhai, Shikui; Yu, Zenghui; Wang, Shujie; Cai, Zongwei

2018-04-01

The study of hydrothermal deposits in the Okinawa Trough can help us to uncover the hydrothermal mineralization characteristics in the back-arc basin during the early expanding stage. Mineralogy and geological significance of hydrothermal deposits from both the middle and southern trough are studied in this paper. First of all, using optical microscope to confirm the mineral compositions, characteristics of crystal shape, paragenetic relationship and minerals crystallization order. Then the minerals chemical composition were analyzed in virtue of electron microprobe. On these basis, the paragenetic sequence and the mineralization characteristics of the hydrothermal deposits were discussed. The results show that the hydrothermal deposit from the mid-Okinawa Trough belongs to Zn-Cu-rich type, consisting dominantly of sulfide minerals such as sphalerite, chalcopyrite, pyrite, etc. The minerals crystallization order is first generation pyrite(PyI)-sphalerite-chalcopyrite-galena-second generation pyrite(PyII)-amorphous silica. While the deposit from the southern Okinawa Trough is Ba-Zn-Pb-rich type mainly composing of barite, sphalerite, galena, etc. The minerals crystallization order is barite-pyrite-sphalerite-tetrahedrite-galena-chalcopyrite-amorphous silica. Hydrothermal fluid temperature in the mid-Okinawa Trough undergoes a process from high to low, which is high up to 350 °C in the early stage, but decreasing gradually with the evolution of hydrothermal fluid. On the contrary, the hydrothermal activity in the southern Okinawa Trough is low temperature dominated, but the mineralization environment is unstable and the fluid temperature changes drastically during the period of hydrothermal activity.

Offshore risk assessment

CERN Document Server

Vinnem, Jan-Erik

2014-01-01

  Offshore Risk Assessment was the first book to deal with quantified risk assessment (QRA) as applied specifically to offshore installations and operations. Risk assessment techniques have been used for more than three decades in the offshore oil and gas industry, and their use is set to expand increasingly as the industry moves into new areas and faces new challenges in older regions.   This updated and expanded third edition has been informed by a major R&D program on offshore risk assessment in Norway and summarizes research from 2006 to the present day. Rooted with a thorough discussion of risk metrics and risk analysis methodology,  subsequent chapters are devoted to analytical approaches to escalation, escape, evacuation and rescue analysis of safety and emergency systems.   Separate chapters analyze the main hazards of offshore structures: fire, explosion, collision, and falling objects as well as structural and marine hazards. Risk mitigation and control are discussed, as well as an illustrat...

Floor cooler for floor trough of a nuclear reactor

International Nuclear Information System (INIS)

Friedrich, H.J.

1985-01-01

Cooling pipes are situated below the floor trough of a BWR, which are connected to the annular distribution or collection pipes. The distribution and collection pipes are connected by parallel hairpin pipes with involute shape to the centre of the floor trough. These hairpin pipes are situated in a lower plane than the annular distribution pipe to the centre and in a higher plane from the centre to the outer annular collector pipe. (orig./HP) [de

Offshore wind energy developments

DEFF Research Database (Denmark)

Stolpe, Mathias; Buhl, Thomas; Sumer, B. Mutlu

2014-01-01

This chapter will give a brief overview of a few of the activities within offshore wind energy research, specifically 1) Support structure optimization, 2) Blade coatings for wind turbines; 3) Scour protection of foundations, 4) Offshore HVDC and 5) Offshore wind services....

Crustal and upper mantle velocity structure of the Salton Trough, southeast California

Science.gov (United States)

Parsons, T.; McCarthy, J.

1996-01-01

This paper presents data and modelling results from a crustal and upper mantle wide-angle seismic transect across the Salton Trough region in southeast California. The Salton Trough is a unique part of the Basin and Range province where mid-ocean ridge/transform spreading in the Gulf of California has evolved northward into the continent. In 1992, the U.S. Geological Survey (USGS) conducted the final leg of the Pacific to Arizona Crustal Experiment (PACE). Two perpendicular models of the crust and upper mantle were fit to wide-angle reflection and refraction travel times, seismic amplitudes, and Bouguer gravity anomalies. The first profile crossed the Salton Trough from the southwest to the northeast, and the second was a strike line that paralleled the Salton Sea along its western edge. We found thin crust (???21-22 km thick) beneath the axis of the Salton Trough (Imperial Valley) and locally thicker crust (???27 km) beneath the Chocolate Mountains to the northeast. We modelled a slight thinning of the crust further to the northeast beneath the Colorado River (???24 km) and subsequent thickening beneath the metamorphic core complex belt northeast of the Colorado River. There is a deep, apparently young basin (???5-6 km unmetamorphosed sediments) beneath the Imperial Valley and a shallower (???2-3 km) basin beneath the Colorado River. A regional 6.9-km/s layer (between ???15-km depth and the Moho) underlies the Salton Trough as well as the Chocolate Mountains where it pinches out at the Moho. This lower crustal layer is spatially associated with a low-velocity (7.6-7.7 km/s) upper mantle. We found that our crustal model is locally compatible with the previously suggested notion that the crust of the Salton Trough has formed almost entirely from magmatism in the lower crust and sedimentation in the upper crust. However, we observe an apparently magmatically emplaced lower crust to the northeast, outside of the Salton Trough, and propose that this layer in part

Chronostratigraphy and deposition rates in the Okinawa Trough region

Institute of Scientific and Technical Information of China (English)

李培英; 王永吉; 刘振夏

1999-01-01

Six representative cores from Okinawa Trough have been dated using AMS 14C, Standard 14C and ESR methods, and comparatively analysed. Systematic measurements of the oriented samples taken from the cores were conducted for obtaining their remnant magnetic polarity. With the aid of the dates obtained, particularly the AMS 14C ages of planktonic foraminiferal tests, two polarity events and two polar wanderings of the earth magnetic field have been defined. Calculations of the deposition rates for all the six core sites indicate rather high values in the trough plain, at least equivalent to those rates reported for the region of the East China Sea. They commonly range from 10 to 30 cm/ka, and even greater than 40 cm/ka in some localities. The deposition rate varied widely with topography and periods of time. In general, it is greater during the postglacial period than during the last glaciation. The chronostratigraphy in the Okinawa Trough region established through this study argues against the pr

Domestic R&D and Offshoring

DEFF Research Database (Denmark)

Junge, Martin; Sørensen, Anders

2017-01-01

survey and register data. No evidence is found for a lower probability of own R&D after offshoring takes place compared to before. Moreover, offshoring does not lead to lower R&D intensity in general. However, firms that offshore R&D activity have larger R&D intensity after offshoring has taken place...

Current trends in offshore technology

International Nuclear Information System (INIS)

Korsgaard, J.

1994-01-01

Although this is a technical symposium concerning advances in the technology of producing oil and gas offshore, a keynote address would not be complete without mentioning non-technical factors which are extremely important for the business of producing oil and gas offshore. These are political factors and economic factors. Offshore operations are an easy target for political forces that are opposed to marine operations involving the production and transfer of hydrocarbons. For example, the oil pollution act of 1990 was a reaction to the Exxon Valdez grounding in Alaska and this act has added significantly to the risk and cost of operating offshore. Another example of this is that it is becoming more and more difficult to dispose of produced water offshore. Producing oil and gas offshore is a business that competes with other energy sources such as coal and oil and gas from wells on land. The offshore oil can only compete with these other resources by providing the same product at a competitive price. Since offshore operations are inherently more costly than land operations, the offshore oil field or gas field must be significantly larger than a land field in order to be produced. Also the offshore oil field or gas field is more susceptible to environmental risks from weather. On a more positive note, there are technical developments which are taking place and have continuously taken place to make offshore oil and gas both more economic and safer to produce. These developments are briefly discussed

Offshoring and International Competitiveness

DEFF Research Database (Denmark)

Ørberg Jensen, Peter D.; Pedersen, Torben

2012-01-01

During the past decade, offshoring has become an established business practice. Yet it is still more common to offshore less advanced tasks compared with offshoring more advanced tasks, i.e., tasks closer to the core activities of the firm. The latter is a new phenomenon which raises many new iss...

Offshore Transmission Technology

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-10-15

The purpose of this document is to give an overview of offshore electricity transmission technologies. In particular this document is concerned with the use of High Voltage Direct Current (HVDC) systems and more specifically with the development of Voltage Source Converter (VSC) technology. This report outlines the current state of the main technology groups required for offshore HVDC transmission as well as giving examples of offshore projects (both current and future). Finally some indications of likely unit costs for HV assets are given.

Complex thrusting at the toe of the Nankai accretionary prism, NanTroSEIZE Kumano transect

Science.gov (United States)

Moore, G. F.; Park, J.; Kodaira, S.; Kaneda, Y.

2009-12-01

Seismic reflection data collected over the past 10 years by the Institute for Research on Earth Evolution (IFREE) of Japan Agency for Marine Earth Science and Technology (JAMSTEC) image a zone of complex thrusting at the toe of the Nankai accretionary prism south of Kii Peninsula, Honshu, Japan. The frontal part of the Nankai prism west of Shionomisaki Canyon (SC) at ~136° E, including the Muroto and Ashizuri Transects off Shikoku, is generally formed of imbricate thrusts with spacing of ~ 1-3 km that dip ~25-35° landward and sole into a prominent décollement. Out-of-sequence thrusts (OOSTs) are usually restricted to the landward margin of this imbricate thrust zone. East of SC, in the Kumano Transect area, the imbricate thrust zone is bounded on its seaward edge by a frontal thrust block that is ~5-6 km wide and consists of several OOSTs. The frontal thrust dips ~5-10° under this ~2-4 km thick block, emplacing this thrust sheet over the trench floor. The number and character of thrusts within the frontal thrust block vary laterally along strike. The 2006 Kumano 3D seismic data set images details of one segment of this complex frontal thrust block. Out-of-sequence faulting has led to underplating of several smaller thrust slices and movement along oblique ramps has led to a complex pattern of faulting that cannot be recognized in even closely-spaced 2D seismic lines. The frontal thrust block is further modified by subduction of seamounts and ridges that have caused large slumps of material from the block.

Outsourcing software development offshore making IT work

CERN Document Server

Gold, Tandy

2004-01-01

THE OFFSHORE IMPERATIVECrunching the Offshore Numbers: What the Financials PortendWelcome to the Definitive Guide on Offshore OutsourcingSetting the Stage: The Compelling Offshore StoryOffshore Outsourcing versus Traditional IT OutsourcingChallenges of Offshore OutsourcingChapter SummaryGetting Started in OffshoreExecutive Support and Communications: The Key to SuccessA Look at an Example of Enlightened Leadership: Handling Employee Impact at a Northeast Utilities CompanyWell-Planned and Executed Communications: A Critical Success Factor for Offshore Program InitiationEstablishing the Offshore

Offshore wind energy prospects

International Nuclear Information System (INIS)

Gaudiosi, Gaetano

1999-01-01

In last two years offshore wind energy is becoming a focal point of national and non national organisations particularly after the limitations of fossil fuel consumption, adopted by many developed countries after Kyoto conference at the end of 1997 on global climate change. North Europe is particularly interested in offshore for the limited land areas still available, due to the intensive use of its territory and its today high wind capacity. Really the total wind capacity in Europe could increase from the 1997 value of 4450 MW up to 40 000 MW within 2010, according the White Paper 1997 of the European Commission; a significant percentage (25%) could be sited offshore up to 10 000 MW, because of close saturation of the land sites at that time. World wind capacity could increase from the 1997 value of 7200 MW up to 60 000 MW within 2010 with a good percentage (20%) offshore 12 000 MW. In last seven years wind capacity in shallow water of coastal areas has reached 34 MW. Five wind farms are functioning in the internal seas of Netherlands, Denmark, Sweden; however such siting is mostly to be considered as semi-offshore condition. Wind farms in real offshore sites, open seas with waves and water depth over 10 m, are now proposed in North Sea at 10-20 km off the coasts of Netherlands, Denmark using large size wind turbine (1-2 MW). In 1997 an offshore proposal was supported in Netherlands by Greenpeace after the OWEMES '97 seminar, held in Italy on offshore wind in the spring 1997. A review is presented in the paper of European offshore wind programs with trends in technology, economics and siting effects. (Author)

Tear trough – Anatomy and treatment by autologous fat grafting

Directory of Open Access Journals (Sweden)

Chang Yung Chia

2016-07-01

Full Text Available Tear trough is the main irregularity at midface, of which treatment is difficult. There is no agreement in literature about its anatomy and best treatment. The author presented an anatomical study and personal autologous fat grafting technique for tear trough treatment. Anatomical dissections were done on two fresh cadavers to examine the skin, subcutaneous, muscle and bone layers, spaces, and attachments. Safety and efficacy were evaluated via retrospective analysis of the last 200 consecutive procedures performed by the author. Tear trough is caused by the abrupt transition of the palpebral orbicular oculi muscle (OOM (i.e., thin skin without subcutaneous fat compartment to the orbital OOM (i.e., thicker skin with malar fat compartment. The tear trough region is located at the OOM bony origin at the medial canthus where no specific ligament was found. The grafted fat volume stabilized at two or three months after the procedure, instead of six months as stated in literature, with excellent results and no severe complications. Tear trough is a personal characteristic, a natural anatomical depression caused by subcutaneous irregularity and can worsen with age. The lack of volume is not effectively corrected by surgeries and thus it must be filled. Fat grafting has several advantages over alloplastic fillers, although it may be more difficult. Fat graft is autologous and abundant, and tissue transplantation could enhance skin quality. Fat grafting is a simple, safe, and effective solution for adding extra volume to correct the deflation phenomenon of the midface aging process. There is no specific anatomical plane for volume injection; the fat graft must be evenly distributed in the deep and superficial plane for uniformity.

Optimized molten salt receivers for ultimate trough solar fields

Science.gov (United States)

Riffelmann, Klaus-J.; Richert, Timo; Kuckelkorn, Thomas

2016-05-01

Today parabolic trough collectors are the most successful concentrating solar power (CSP) technology. For the next development step new systems with increased operation temperature and new heat transfer fluids (HTF) are currently developed. Although the first power tower projects have successfully been realized, up to now there is no evidence of an all-dominant economic or technical advantage of power tower or parabolic trough. The development of parabolic trough technology towards higher performance and significant cost reduction have led to significant improvements in competitiveness. The use of molten salt instead of synthetic oil as heat transfer fluid will bring down the levelized costs of electricity (LCOE) even further while providing dispatchable energy with high capacity factors. FLABEG has developed the Ultimate TroughTM (UT) collector, jointly with sbp Sonne GmbH and supported by public funds. Due to its validated high optical accuracy, the collector is very suitable to operate efficiently at elevated temperatures up to 550 °C. SCHOTT will drive the key-innovations by introducing the 4th generation solar receiver that addresses the most significant performance and cost improvement measures. The new receivers have been completely redesigned to provide a product platform that is ready for high temperature operation up to 550 °C. Moreover distinct product features have been introduced to reduce costs and risks in solar field assembly and installation. The increased material and design challenges incurred with the high temperature operation have been reflected in sophisticated qualification and validation procedures.

Morphological evolution of Jinshan Trough in Hangzhou Bay (China) from 1960 to 2011

Science.gov (United States)

Liu, Yifei; Xia, Xiaoming; Chen, Shenliang; Jia, Jianjun; Cai, Tinglu

2017-11-01

An extensive system of tidal channels, starting with Jinshan Trough in the east, is located along the north shore of Hangzhou Bay, China. This contribution investigates the morphological evolution of Jinshan Trough by using 17 bathymetric charts from a series covering a period of 51 years from 1960 to 2011. Three stages of evolution during this period are distinguishable based on the morphology and annual mean volume data. The first stage (1960-1987) is characterized by extension of the trough; the second stage (1987-1996) is a relatively stable period with some adjustments in the trough morphology; the third stage (1996-2011) is marked by the processes of erosion and deposition in the beginning of the period and a subsequent slow erosion process. Spatio-temporal variability of the trough was evaluated by using empirical orthogonal function (EOF) analysis. The first eigenfunction indicates that erosion is the main evolution process and there exists three stages similar to those distinguished from volume variations. The second eigenfunction mainly reflects erosion and deposition in the northwest part of the trough located in the flood tidal current shadow area of the artificial headland in Jinshan. The third eigenfunction mainly reflects annual fluctuations of erosion and deposition in the side slope at the artificial headland in Jinshan. A particularly intense erosion process occurred between 1996 and 1998. The major effects on morphological evolution in Jinshan Trough from 1960 to 2011 were investigated and tentative conclusions were presented. Continuous coastal reclamations in Jinshan had the most pronounced effect on the morphological evolution during the first and the second stages. The storm surge had a pronounced effect on the evolution at the beginning of the third stage.

Assessing offshore wind potential

International Nuclear Information System (INIS)

Adelaja, Adesoji; McKeown, Charles; Calnin, Benjamin; Hailu, Yohannes

2012-01-01

Quantifying wind potential is a pivotal initial step in developing and articulating a state’s policies and strategies for offshore wind industry development. This is particularly important in the Great Lakes States where lessons from other offshore environments are not directly applicable. This paper presents the framework developed for conducting a preliminary assessment of offshore wind potential. Information on lake bathymetry and wind resources were combined in simulating alternative scenarios of technically feasible turbine construction depths and distance concerns by stakeholders. These yielded estimates of developable offshore wind areas and potential power generation. While concerns about the visibility of turbines from shore reduce the power that can be generated, engineering solutions that increase the depths at which turbines can be sited increase such potential power output. This paper discusses the costs associated with technical limitations on depth and the social costs related to public sentiments about distance from the shoreline, as well as the possible tradeoffs. The results point to a very large untapped energy resource in the Michigan’s Great Lakes, large enough to prompt policy action from the state government. - Highlights: ▶ We build a theoretical framework for modeling offshore wind power production. ▶ Illustration of the impact of technology and social limitations on offshore wind energy development. ▶ Geospatial modeling of the offshore wind potential of the Great Lakes.

Optical properties of V-trough concentrators

Energy Technology Data Exchange (ETDEWEB)

Fraidenraich, N. [Universidade Federal de Pernambuco, Recife, PE Brasil (Brazil); Almeida, G. J.

1991-07-01

A new approach to study the optical behavior of V-trough concentrators is developed, based on the use of three characteristic angles defining the appearance, disappearance and return to the outside space of the cavity of a reflection mode. The probability of occurrence of a given number of reflections for beam radiation is determined as a function of these angles and the optical efficiency calculated. It is shown that the optical efficiency can be approximated by a function of two parameters, the angular acceptance function, T, and the mean number of reflections, n, as T * p{sup n/T}. Deviations between exact and approximate optical efficiency increase as n increases or as p decreases. For troughs with C ≤ 2.5 the maximal error for beam radiation is 3.4% for p ≥ 0.8 (8.3% for p ≥ 0.7). For diffuse radiation the maximal error is less than 2% for configurations whose optical efficiency is above 0.6. A further simplification was introduced to obtain the optical efficiency for diffuse radiation, approximating T by an analytical expression and n by an empirical linear function of the inverse of the vertex angle. Results accurate up to 5% for p = 0.8, were obtained. Increasing the concentration ratio, C, from 1.5 to 2.5 for a vertex angle being one third of the acceptance angle, decreased the optical efficiency from 0.74 to 0.59, for p = 0.8. For a given C, the dependence of the optical efficiency on the vertex angle is rather weak, suggesting that large trough angles might be favoured by cost-benefit analysis. (author)

Wind energy in offshore grids

DEFF Research Database (Denmark)

Schröder, Sascha Thorsten

special characteristics of offshore grids. With an operational real options approach, it is furthermore illustrated how different support schemes and connections to additional countries affect the investment case of an offshore wind farm and the income of the transmission system operator. The investment...... and investment implications under different regulatory frameworks are a hitherto underrepresented research field. They are addressed by this thesis. Offshore grids between several countries combine the absorption of wind energy with international power trading. However, the inclusion into an offshore grid......This cumulative PhD thesis deals with wind integration in offshore grids from an economic point of view. It is composed of a generic part and eight papers. As the topic has mostly been analysed with a focus on topology and technical issues until now, market-operational questions in offshore grids...

The Hidden Costs of Offshoring

DEFF Research Database (Denmark)

Møller Larsen, Marcus; Manning, Stephan; Pedersen, Torben

2011-01-01

of offshoring. Specifically, we propose that hidden costs can be explained by the combination of increasing structural, operational and social complexity of offshoring activities. In addition, we suggest that firm orientation towards organizational design as part of an offshoring strategy and offshoring......This study seeks to explain hidden costs of offshoring, i.e. unexpected costs resulting from the relocation of business tasks and activities outside the home country. We develop a model that highlights the role of complexity, design orientation and experience in explaining hidden costs...... experience moderate the relationship between complexity and hidden costs negatively i.e. reduces the cost generating impact of complexity. We develop three hypotheses and test them on comprehensive data from the Offshoring Research Network (ORN). In general, we find support for our hypotheses. A key result...

Offshore Wind Energy Market Overview (Presentation)

Energy Technology Data Exchange (ETDEWEB)

Baring-Gould, I.

2013-07-01

This presentation describes the current international market conditions regarding offshore wind, including the breakdown of installation costs, how to reduce costs, and the physical siting considerations considered when planning offshore wind construction. The presentation offers several examples of international existing and planned offshore wind farm sites and compares existing international offshore resources with U.S. resources. The presentation covers future offshore wind trends and cites some challenges that the United States must overcome before it will be able to fully develop offshore wind sites.

Offshore investments-cui prodis? Schrodinger's cat in offshore financing: Both alive and dead

Directory of Open Access Journals (Sweden)

Stepuk Anna

2014-01-01

Full Text Available Trends of FDI in offshore tax havens were compared to efforts and efficiency of regulatory authorities to prevent money laundering. Based on available data it was stated that current position in offshore FDI stays alive and officially dead at the same time, keeping the balance of interests for the main stakeholders: corporations, authorities and financial institutes support further offshore investments. Analysis based on volumes of trade and financial transactions between offshore centers, developed and developing countries. As a result withdrawal of financial resources from the developing countries degrades social capital funding and supports corruption growth.

Analysis of Earthquake Source Spectra in Salton Trough

Science.gov (United States)

Chen, X.; Shearer, P. M.

2009-12-01

Previous studies of the source spectra of small earthquakes in southern California show that average Brune-type stress drops vary among different regions, with particularly low stress drops observed in the Salton Trough (Shearer et al., 2006). The Salton Trough marks the southern end of the San Andreas Fault and is prone to earthquake swarms, some of which are driven by aseismic creep events (Lohman and McGuire, 2007). In order to learn the stress state and understand the physical mechanisms of swarms and slow slip events, we analyze the source spectra of earthquakes in this region. We obtain Southern California Seismic Network (SCSN) waveforms for earthquakes from 1977 to 2009 archived at the Southern California Earthquake Center (SCEC) data center, which includes over 17,000 events. After resampling the data to a uniform 100 Hz sample rate, we compute spectra for both signal and noise windows for each seismogram, and select traces with a P-wave signal-to-noise ratio greater than 5 between 5 Hz and 15 Hz. Using selected displacement spectra, we isolate the source spectra from station terms and path effects using an empirical Green’s function approach. From the corrected source spectra, we compute corner frequencies and estimate moments and stress drops. Finally we analyze spatial and temporal variations in stress drop in the Salton Trough and compare them with studies of swarms and creep events to assess the evolution of faulting and stress in the region. References: Lohman, R. B., and J. J. McGuire (2007), Earthquake swarms driven by aseismic creep in the Salton Trough, California, J. Geophys. Res., 112, B04405, doi:10.1029/2006JB004596 Shearer, P. M., G. A. Prieto, and E. Hauksson (2006), Comprehensive analysis of earthquake source spectra in southern California, J. Geophys. Res., 111, B06303, doi:10.1029/2005JB003979.

Petrologic perspectives on tectonic evolution of a nascent basin (Okinawa Trough) behind Ryukyu Arc:A review

Institute of Scientific and Technical Information of China (English)

YAN Quanshu; SHI Xuefa

2014-01-01

Okinawa Trough is a back-arc, initial marginal sea basin, located behind the Ryukyu Arc-Trench System. The formation and evolution of the Okinawa Trough is intimately related to the subduction process of the Philippine Sea Plate beneath the Eurasian Plate since the late Miocene. The tectonic evolution of the trough is similar to other active back-arcs, such as the Mariana Trough and southern Lau Basin, all of which are experiencing the initial rifting and subsequent spreading process. This study reviews all petrologic and geochemical data of mafic volcanic lavas from the Okinawa Trough, Ryukyu Arc, and Philippine Sea Plate, combined with geophysical data to indicate the relationship between the subduction sources (input) and arc or back-arc magmas (output) in the Philippine Sea Plate-Ryukyu Arc-Okinawa Trough system (PROS). The results obtained showed that several components were variably involved in the petrogenesis of the Oki-nawa Trough lavas:sub-continental lithospheric mantle underlying the Eurasian Plate, Indian mid-oceanic ridge basalt (MORB)-type mantle, and Pacific MORB-type mantle. The addition of shallow aqueous fluids and deep hydrous melts from subducted components with the characteristics of Indian MORB-type mantle into the mantle source of lavas variably modifies the primitive mantle wedge beneath the Ryukyu and sub-continental lithospheric mantle (SCLM) beneath the Okinawa Trough. In the northeastern end of the trough and arc, instead of Indian MORB-type mantle, Pacific MORB-type mantle dominates the magma source. Along the strike of the Ryukyu Arc and Okinawa Trough, the systematic variations in trace element ratios and isotopic compositions reflect the first-order effect of variable subduction input on the magma source. In general, petrologic data, combined with geophysical data, imply that the Okinawa Trough is experiencing the“seafloor spreading”process in the southwest segment,“rift propagation”process in the middle seg-ment, and�

The Nova-Canton Trough and the Late Cretaceous evolution of the central Pacific

Science.gov (United States)

Joseph, Devorah; Taylor, Brain; Shor, Alexander N.; Yamazaki, Toshitsugu

Free-air gravity anomalies derived from satellite altimetry data show that the major Pacific fracture zones, from the Pau to Marquesas, are co-polar about an Euler pole located at 150.5°W, 34.6°S for the period preceding chron 33 and including a large portion of the Cretaceous Normal Superchron. They also show continuity of the Clipperton Fracture Zone through the Line Islands to the Nova-Canton ridge and trough; this Canton-Clipperton trend is co-polar to the same pole. Sidescan-sonar and bathymetry data in the Nova-Canton Trough region reveal N140°E-striking abyssal hill topography south of the N70°E-striking structures of the Nova-Canton Trough and crustal fabric striking normal to the trough (N160°E) to the north. We conclude that the Nova-Canton Trough is the Middle Cretaceous extension of the Clipperton Fracture Zone. We propose that the anomalous depths (7000-8400 m) of the trough between 167°30'-168°30'W are the result of a complex plate reorganization. Conjugate magnetic anomaly lineations M1-M3 in the Phoenix lineations between the Central Pacific Fracture Zone and the Phoenix Fracture Zone and the absence of lineations younger than anomaly M3 west of the Phoenix Fracture Zone suggest that spreading may have gradually ceased along the Pacific-Phoenix system from west to east. We infer that the remaining active segment of the Pacific-Phoenix spreading system after anomaly M1 time was the easternmost section of the Phoenix lineations. At ˜M0 time, the Pacific-Phoenix spreading axis stretched from lineated bathymetric depressions lying between 180°W and the Phoenix Islands to ˜168°W and included the western deep of the Nova-Canton Trough. We hypothesize that accretion terminated on the Pacific-Phoenix spreading axis shortly after M0 time and that the absence of an M0 isochron in the region between the eastern Phoenix lineations and the Nova-Canton Trough, or along the Nova-Canton Trough itself, may be due to a decrease in spreading rate prior to

Advanced photovoltaic-trough development

Energy Technology Data Exchange (ETDEWEB)

Spencer, R.; Yasuda, K.; Merson, B.

1982-04-01

The scope of the work on photvoltaic troughs includes analytical studies, hardware development, and component testing. Various aspects of the system have been optimized and improvements have been realized, particularly in the receiver and reflecting surface designs. An empirical system performance model has been developed that closely agrees with measured system performance. This in-depth study of single-axis reflecting linear focus photovoltaic concentrators will be very beneficial in the development of improved models for similar systems as well as other phtovoltaic concentrator designs.

Holocene tephra deposits in the northern Okinawa Trough

Institute of Scientific and Technical Information of China (English)

无

2006-01-01

The mineralogical and geochemical characteristics of sediments of Core CSH1, which was collected from the northern Okinawa Trough, indicate that large amounts of volcanic materials have deposited in the northern Okinawa Trough during the Holocene. On the basis of down-core variations in mineral and element contents of sediments, two layers in the uppermost section of Core CSH1 characterized by high quartz, Na2O, MnO, K2O, uranium contents and low contents of clay minerals, volatiles, Fe2O3, MgO, CaO and strontium, have been identified as the tephra deposits. Systematic grain-size measurements also suggest that sediments from the northern Okinawa Trough are made up of terrigenous materials and volcanic ashes with different proportion during the Holocene. The sediments of tephra layers in Core CSH1 show bi-modal patterns in grain-size distribution with modal grain-sizes of 74.3 and 7.81 μm,respectively. According to the radiocarbon dating on shells of zooplankton foraminifera, two tephra layers in Core CSH1, formed at 7 250 and 10 870 a BP (cal), approximately correspond to the K-Ah tephra [7 300 a BP (cal)] and the eruption of Kuju Volcano (12～10 ka BP), respectively.

Offshoring research directions

NARCIS (Netherlands)

Velthuijsen, Hugo

2012-01-01

Outsourcing and offshoring provide companies with ways to achieve their business objectives better or more cost effectively or despite a shortage of specific resources. From a research point of view, outsourcing and offshoring have mostly been studied as something that large companies do, not small

National Offshore Wind Energy Grid Interconnection Study

Energy Technology Data Exchange (ETDEWEB)

Daniel, John P. [ABB Inc; Liu, Shu [ABB Inc; Ibanez, Eduardo [National Renewable Energy Laboratory; Pennock, Ken [AWS Truepower; Reed, Greg [University of Pittsburgh; Hanes, Spencer [Duke Energy

2014-07-30

The National Offshore Wind Energy Grid Interconnection Study (NOWEGIS) considers the availability and potential impacts of interconnecting large amounts of offshore wind energy into the transmission system of the lower 48 contiguous United States. A total of 54GW of offshore wind was assumed to be the target for the analyses conducted. A variety of issues are considered including: the anticipated staging of offshore wind; the offshore wind resource availability; offshore wind energy power production profiles; offshore wind variability; present and potential technologies for collection and delivery of offshore wind energy to the onshore grid; potential impacts to existing utility systems most likely to receive large amounts of offshore wind; and regulatory influences on offshore wind development. The technologies considered the reliability of various high-voltage ac (HVAC) and high-voltage dc (HVDC) technology options and configurations. The utility system impacts of GW-scale integration of offshore wind are considered from an operational steady-state perspective and from a regional and national production cost perspective.

Offshore concrete structures; Estructuras Offshore (mar adentro) de Hormigon

Energy Technology Data Exchange (ETDEWEB)

Lamas Pardo, M.; Carral Couce, L. M.

2011-07-01

In the offshore industry there are two possible materials for the construction of the hull of a structure; the steel and concrete, with the first one widely used until now, as in the rest of the shipbuilding industry of merchant ships, warships, etc. Materials such as aluminum, GRP or timber areused in small units with lengths lower than 100 m, and in less adverse conditions than in the offshore industry. Nevertheless, some ships/barges have been built of concrete in the past, but have been rather isolated cases which have not changed the practice in the industry. In the First and Second World War were built by the scarcity of materials, while the series of barges by Alfred A. Yee was a rare exception. Other units were also made in concrete, but almost anecdotal. Still, the behaviour of these concrete structures, especially in terms of maintenance, has been excellent. Therefore, the fact that the concrete has not had an adequate reception so far in shipbuilding, does not mean that in will not be the material best suited for the offshore industry in the future. The extra displacement and associated fuel costs in concrete ships have been found prohibitive in the past. But the loss of mobility of a concrete hull in relation to a steel hull can be perfectly offset by the advantages offered by the concrete, as the shipping and offshore industry have very different priorities. One of the main differences in these priorities is in terms of maintenance and resistance to fatigue, precisely where the concrete performs better. ships can easily be dry docked for maintenance and repair, while in the offshore platforms these works have to be done in situ so maintenance and fatigue are crucial to them. Besides these, the concrete has other advantages according to findings of several studies. And although they are interested in the conclusions that the makes as they came from people in the concrete industry, the fact that in recent years concrete offshore unit shave been built

Offshore investments: Denmark shows the way

International Nuclear Information System (INIS)

Anon.

1998-01-01

This article presents an overview of the use of wind power in Denmark and discusses the tremendous growth in the manufacture of wind turbines since 1981 with Denmark holding some 60% of the worlds' wind turbine market. The move to offshore wind farms is explained in terms of the shortage of land and the quality of the offshore wind, and details of the Tuno Knob pilot offshore wind farm are given. Offshore wind power in Europe, the challenges to offshore operations, the costs involved, environmental effects of the use of offshore wind, and the growing amount of wind power capacity are discussed

Global offshore pipeline markets

International Nuclear Information System (INIS)

Knight, R.; Parsons, B.

2001-01-01

In this article, two experts forecast a recovery in the offshore pipeline market followed by accelerating growth. A number of clearly definable macro trends are affecting the world offshore oil and gas industry and will be of considerable significance to the offshore pipelines industry. The authors' view is of markets that show every chance of enjoying long-term growth prospects driven by the fundamentals of a continuing increase in demand for offshore oil and gas. The offshore industry however has a highly cyclical nature, due to the impact of variations in oil and gas prices and the differing state of maturity of individual regions. Therefore those companies that are able to offer the widest range of pipe types and diameters and methods of installation across the greatest range of geographic markets are likely to prosper most. Thus, this continues to be a market best suited to those able to operate on a global scale and make a corporate commitment measured in decades

Panorama 2012 - Offshore hydrocarbons

International Nuclear Information System (INIS)

Serbutoviez, Sylvain

2011-12-01

Technological progress is enabling production from offshore oil and gas fields at increasingly ambitious depths (3, 000 metres). Investment in offshore production is running at around $100 billion per year, accounting for one-fifth of all investment in oil exploration and development worldwide. However, the global economic crisis that broke at the end of 2008 and the accident involving the Macondo well temporarily disrupted the race to deep offshore technology. (author)

High-resolution records of thermocline in the Okinawa Trough since about 10000 aBP

Institute of Scientific and Technical Information of China (English)

无

2001-01-01

The present paper uses planktonic foraminifera and their stableisotopes to study the changes in the depth of thermocline (DOT) in the Okinawa Trough since the last 10000 a based on the analysis of Core B-3GC in the northern Okinawa Trough, together with that of the core in the southern Okinawa Trough. As results show, the thermocline was shallow before 6400 aBP, and deepened afterward, then became shallow again from 4000 to 2000 aBP. The DOT fluctuations display a positive correlation with those of sea surface temperature (SST). In addition, the changes in the northern Okinawa Trough are similar to those in the southern trough, implying a possible connection with the variation of the Kuroshio Current. The changes of SST and DOT suggest that the Kuroshio Current changed its intensity or main axis from 4000 to 2000 aBP and around about 6400 aBP respectively. Moreover, the changes of DOT from 8200 to 6400 aBP may indicate a gradual intensification of the Kuroshio Current.

New sidescan sonar and gravity evidence that the Nova-Canton Trough is a fracture zone

Science.gov (United States)

Joseph, Devorah; Taylor, Brian; Shor, Alexander N.

1992-05-01

A 1990 sidescan sonar survey in the eastern region of the Nova-Canton Trough mapped 138°-striking abyssal-hill fabric trending into 70°-striking trough structures. The location and angle of intersection of the abyssal hills with the eastern Nova-Canton Trough effectively disprove a spreading-center origin of this feature. Free-air gravity anomalies derived from satellite altimetry data show continuity, across the Line Islands, of the Nova-Canton Trough with the Clipperton Fracture Zone. The Canton-Clipperton trend is copolar, about a pole at 30°S, 152°W, with other coeval Pacific-Farallon fracture-zone segments, from the Pau to Marquesas fracture zones. This copolarity leads us to postulate a Pacific-Farallon spreading pattern for the magnetic quiet zone region north and east of the Manihiki Plateau, with the Nova-Canton Trough originating as a transform fault in this system.

Offshore industry: medical emergency response in the offshore oil and gas industry.

Science.gov (United States)

Ponsonby, Will; Mika, Frano; Irons, Greg

2009-08-01

The hunt for oil and gas has taken workers into new more distant locations including those offshore. The remoteness of the offshore platforms and vessels coupled with the potential risk of being cut off by bad weather presents particular challenges for medical emergency response (MER). Firstly to define the challenges for MER in terms of locations, population and epidemiology of injuries and illnesses in the offshore environment. Secondly to give examples of legal requirements and industry standards to manage MER. Thirdly to look at existing and emerging practice to manage these challenges. A review of published literature was supplemented with a summary of current practice in the industry. Medical professionals (medics) working offshore on installations and vessels are primarily responsible for the medical care of the workers. The medics have clinics with suitable medical equipment for managing emergencies as well as providing limited primary care. Some countries have legislation that stipulate minimum requirements. Where there is no national legislation, industry and company guidance is used to define the MER standards. Supervision of the offshore medics is often provided by doctors on shore via radio and phone links. These methods of communication are now being augmented with more sophisticated telemedicine solutions such as the Internet and live video links. These newer solutions allow for prompt high-quality care and provide the scope for a variety of new treatment options to be available for the offshore workforce.

Improvement Design of Parabolic Trough

Science.gov (United States)

Ihsan, S. I.; Safian, M. A. I. M.; Taufek, M. A. M.; Mohiuddin, A. K. M.

2017-03-01

The performance of parabolic trough solar collector (PTSC) has been evaluated using different heat transfer working fluids; namely water and SAE20 W50 engine oil. New and slightly improved PTSC was developed to run the experimental study. Under the meteorological conditions of Malaysia, authors found that PTSC can operate at a higher temperature than water collector but the performance efficiency of collector using engine oil is much lower than the water collector.

O+ trough zones in the polar cap ionosphere-magnetosphere coupling region

Science.gov (United States)

Horwitz, James; Zeng, Wen; Jaafari, Fajer

Regions of low-density troughs in O+ have been observed at 1 RE altitude in the polar cap ionosphere-magnetosphere region by the Thermal Ion Dynamics Experiment(TIDE) on the POLAR spacecraft. In this presentation, the UT Arlington Dynamic Fluid-Kinetic (DyFK) code is employed to investigate the formation of such O+ density troughs. We utilize convection paths of flux tubes in the high-latitude region as prescribed by an empirical convection model with solar wind inputs to track the evolution of ionospheric plasma transport and in particular O+ densities along these tubes with time/space. The flux tubes are subjected to auroral processes of precipitation and wave-driven ion heating when they pass through the auroral oval, which tends to elevate the plasma densities in these tubes. When the F-regions of such tubes traverse locations where the F-region is in darkness, recombination there causes the higher-altitude regions to drain and the densities to decline throughout. Owing to the varying effects of these processes, significant and low trough-like densities at higher altitudes developed along these flux tubes. The modeled densities near 6000 km altitudes will be compared with multiple POLAR passes featuring POLAR/TIDE-measured O+ densities for inside and outside of such trough regions.

Uncovering the Hidden Costs of Offshoring

DEFF Research Database (Denmark)

Larsen, Marcus M.; Manning, Stephan; Pedersen, Torben

2013-01-01

This study investigates estimation errors due to hidden costs—the costs of implementation that are neglected in strategic decision-making processes—in the context of services offshoring. Based on data from the Offshoring Research Network, we find that decision makers are more likely to make cost......-estimation errors given increasing configuration and task complexity in captive offshoring and offshore outsourcing, respectively. Moreover, we show that experience and a strong orientation toward organizational design in the offshoring strategy reduce the cost-estimation errors that follow from complexity. Our...

Methane accumulation and forming high saturations of methane hydrate in sandy sediments

Energy Technology Data Exchange (ETDEWEB)

Uchida, T.; Waseda, A. [JAPEX Research Center, Chiba (Japan); Fujii, T. [Japan Oil, Gas and Metals National Corp., Chiba (Japan). Upstream Technology Unit

2008-07-01

Methane supplies for marine gas hydrates are commonly attributed to the microbial conversion of organic materials. This study hypothesized that methane supplies were related to pore water flow behaviours and microscopic migration in intergranular pore systems. Sedimentology and geochemistry analyses were performed on sandy core samples taken from the Nankai trough and the Mallik gas hydrate test site in the Mackenzie Delta. The aim of the study was to determine the influence of geologic and sedimentolic controls on the formation and preservation of natural gas hydrates. Grain size distribution curves indicated that gas hydrate saturations of up to 80 per cent in pore volume occurred throughout the hydrate-dominant sand layers in the Nankai trough and Mallik areas. Water permeability measurements showed that the highly gas hydrate-saturated sands have a permeability of a few millidarcies. Pore-space gas hydrates occurred primarily in fine and medium-grained sands. Core temperature depression, core observations, and laboratory analyses of the hydrates confirmed the pore-spaces as intergranular pore fillings. Results of the study suggested that concentrations of gas hydrates may require a pore space large enough to occur within a host sediments, and that the distribution of porous and coarser-grained sandy sediments is an important factor in controlling the occurrence of gas hydrates. 11 refs., 4 figs.

Tidal influence on offshore wind fields and resource predictions[Efficient Development of Offshore Windfarms

Energy Technology Data Exchange (ETDEWEB)

Khan, D. [Entec UK Ltd., Doherty Innovation Centre, Penicuik (United Kingdom); Infield, D. [Loughborough Univ., Centre for Renewable Energy Systems Tecnology, Loughborough (United Kingdom)

2002-03-01

The rise and fall of the sea surface due to tides effectively moves an offshore wind turbine hub through the wind shear profile. This effect is quantified using measured data from 3 offshore UK sites. Statistical evidence of the influence of tide on mean wind speed and turbulence is presented. The implications of this effect for predicting offshore wind resource are outlined. (au)

Processes influencing differences in Arctic and Antarctic Trough Mouth Fan sedimentology

OpenAIRE

Gales, J; Hillenbrand, C-D; Larter, R; Laberg, J-S; Melles, M; Benetti, S; Passchier, S

2018-01-01

Trough Mouth Fans (TMFs) are sediment depocentres that form along high-latitude continental margins at the mouths of some cross-shelf troughs. They reflect the dynamics of past ice sheets over multiple glacial cycles and processes operating on (formerly) glaciated continental shelves and slopes, such as erosion, reworking, transport and deposition. The similarities and differences in TMF morphology and formation processes of the Arctic and Antarctic regions remain poorly constrained. Here, we...

Healthy offshore workforce? A qualitative study on offshore wind employees' occupational strain, health, and coping.

Science.gov (United States)

Mette, Janika; Velasco Garrido, Marcial; Harth, Volker; Preisser, Alexandra M; Mache, Stefanie

2018-01-23

Offshore work has been described as demanding and stressful. Despite this, evidence regarding the occupational strain, health, and coping behaviors of workers in the growing offshore wind industry in Germany is still limited. The purpose of our study was to explore offshore wind employees' perceptions of occupational strain and health, and to investigate their strategies for dealing with the demands of offshore work. We conducted 21 semi-structured telephone interviews with employees in the German offshore wind industry. The interviews were transcribed and analyzed in a deductive-inductive approach following Mayring's qualitative content analysis. Workers generally reported good mental and physical health. However, they also stated perceptions of stress at work, fatigue, difficulties detaching from work, and sleeping problems, all to varying extents. In addition, physical health impairment in relation to offshore work, e.g. musculoskeletal and gastrointestinal complaints, was documented. Employees described different strategies for coping with their job demands. The strategies comprised of both problem and emotion-focused approaches, and were classified as either work-related, health-related, or related to seeking social support. Our study is the first to investigate the occupational strain, health, and coping of workers in the expanding German offshore wind industry. The results offer new insights that can be utilized for future research in this field. In terms of practical implications, the findings suggest that measures should be carried out aimed at reducing occupational strain and health impairment among offshore wind workers. In addition, interventions should be initiated that foster offshore wind workers' health and empower them to further expand on effective coping strategies at their workplace.

Co-sourcing in software development offshoring

DEFF Research Database (Denmark)

Schlichter, Bjarne Rerup; Persson, John Stouby

2013-01-01

Software development projects are increasingly geographical distributed with offshoring, which introduce complex risks that can lead to project failure. Co-sourcing is a highly integrative and cohesive approach, seen successful, to software development offshoring. However, research of how co......-sourcing shapes the perception and alleviation of common offshoring risks is limited. We present a case study of how a certified CMMI-level 5 Danish software supplier approaches these risks in offshore co-sourcing. The paper explains how common offshoring risks are perceived and alleviated when adopting the co...

Design off-shore wind climate

Energy Technology Data Exchange (ETDEWEB)

Larsen, G C; Joergensen, H E [Risoe National Lab., Wind Energy and Atmospheric Physics Dept., Roskilde (Denmark)

1999-03-01

Specific recommendations of off-shore turbulence intensities, applicable for design purposes, are lacking in the present IEC-code. The present off-shore wind climate analysis presents the distribution of the turbulence standard deviation around the mean turbulence standard deviation, conditioned on the mean wind speed. Measured distributions, based on a huge amount of measuring data from two shallow water off-shore sites, are parameterized by fitting to a three parameter Weibull distribution. Combining a simple heuristic load model with the parameterized probability density functions of the turbulence standard deviations, an empirical off-shore design turbulence intensity is evaluated that in average yields the same fatigue damage as the distributed turbulence intensity. The proposed off-shore design turbulence intensity is, within the IEC code framework, applicable for extreme as well as for fatigue load determination. (au)

OFFSHORING FOR SUSTAINABLE VALUE MANAGEMENT

Directory of Open Access Journals (Sweden)

Thaddeus Oforegbunam Ebiringa

2014-05-01

Full Text Available This paper evaluates offshoring as a strategic value management initiative using Cadbury Nigeria Plc as a case study. Through offshoring risks associated with inventory holding are hedged. A comparative analysis of in-house and offshored cost profiles as well as critical risk factors that affect firm value are evaluated. The result shows that offshoring led to immediate costs saving, freeing of funds previously held in inventory for other working capital investments as well as profitability for vendors. However, aside financial benefits to partners, it leads to increased stakeholders awareness, shared values, partnerships, teamwork and risk mitigation. It therefore follows that for sustainability of financial benefits of offshoring, concerted effort must be made by partners to ensure that critical drivers of value management are not compromised.

Gas Turbine/Solar Parabolic Trough Hybrid Design Using Molten Salt Heat Transfer Fluid: Preprint

Energy Technology Data Exchange (ETDEWEB)

Turchi, C. S.; Ma, Z.

2011-08-01

Parabolic trough power plants can provide reliable power by incorporating either thermal energy storage (TES) or backup heat from fossil fuels. This paper describes a gas turbine / parabolic trough hybrid design that combines a solar contribution greater than 50% with gas heat rates that rival those of natural gas combined-cycle plants. Previous work illustrated benefits of integrating gas turbines with conventional oil heat-transfer-fluid (HTF) troughs running at 390?C. This work extends that analysis to examine the integration of gas turbines with salt-HTF troughs running at 450 degrees C and including TES. Using gas turbine waste heat to supplement the TES system provides greater operating flexibility while enhancing the efficiency of gas utilization. The analysis indicates that the hybrid plant design produces solar-derived electricity and gas-derived electricity at lower cost than either system operating alone.

Fault system and thermal regime in the vicinity of site NGHP-01-10, Krishna-Godavari basin, Bay of Bengal

Digital Repository Service at National Institute of Oceanography (India)

Dewangan, P.; Srirama, G.; Ramprasad, T.; Ramana, M.V.; Jaiswal, P.

driven (Milkov and Sassen, 2002). In structural accumulation gases are transported to the GHSZ through features such as faults and mud 3 volcanoes, e.g. northwestern Gulf of Mexico (Brooks et al., 1986; MacDonald et al., 1994; Milkov and Sassen, 2000... horizons, e.g., Blake ridge (Xu and Ruppel, 1999; Dickens et al., 1997), Gulf of Mexico minibasins (Milkov and Sassen, 2001; Pflaum et al., 1986), Nankai trough (Matsumoto et al., 2001), and Mallik (Dallimore et al., 1999). A combination of both...

Offshore oil and gas and offshore wind power - different in terms of safety.?; Offshore Oel and Gas und Offshore Wind - mit Sicherheit ''anders''.?

Energy Technology Data Exchange (ETDEWEB)

Weise, F.; Tatulinski, M. [DNV GL - Oil and Gas Germany, Hamburg (Germany)

2014-07-01

Safety standards in the oil and gas industry have risen to a high level over the past decades, driven in part by momentous accidents. Furthermore, an expanded framework has recently been defined through the new EU Offshore Safety Directive, which in Germany is still in the process of its transposition into national law. The installation of offshore wind farms in the North and Baltic Sea has within the shortest of time brought forth an entirely new branch of industry, most of whose players have no significant experience with offshore operations. One of the greatest challenges is the working environment, which is being approached in different ways by those involved. The supervisory authorities responsible are only just beginning to develop the competence required for their tasks, with the effect that regulations pertaining to onshore operations are often simply adopted as they are. This is in some cases impacting on the oil and gas industry, as is discussed in the present lecture. [German] Die Oel und Gas Industrie hat in den vergangen Jahrzehnten einen hohen Sicherheitsstandard entwickelt, teilweise getrieben durch signifikante Unfallereignisse. Aktuell wurde zudem mit der neuen EU-Offshore Richtlinie ein erweiterter Rahmen definiert, der sich in Deutschland noch in der gesetzgeberischen Umsetzung befindet. Durch die Installation von Offshore-Windparks in der Nord- und Ostsee ist innerhalb kuerzester Zeit zusaetzlich ein neuer Industriebereich entstanden, dessen Marktteilnehmer mehrheitlich nicht ueber signifikante Offshore-Erfahrung verfuegen. Insbesondere das Arbeitsumfeld stellt dabei eine Herausforderung dar, die von den Beteiligten unterschiedlich geloest wird. Ferner beginnen auch die verantwortlichen Aufsichtsbehoerden erst mit dem Aufbau entsprechender Kompetenzen, so dass vielfach auch Regelungen aus dem Onshore-Bereich uebertragen werden. Dies fuehrt teilweise zu Auswirkungen auf die Oel- und Gasindustrie, die im Rahmen dieses Vortrages diskutiert werden.

Dutch offshore suppliers in confident mood

International Nuclear Information System (INIS)

Beudel, M.

1998-01-01

A series of linked articles discusses the current state of the Netherland's offshore industry. Reduced taxes, and availability of exploration licenses has meant that explorers and producers are drawn to the small size, but frequent yield explorations on Holland's continental shelf. The excellent operation record of Rotterdam's Verolme Botlek yard; for repair and maintenance of offshore platforms and associated plant, is explored as the facility plans to diversify into newbuilding. The construction of an offshore basin designed for the hydrodynamic testing of offshore plant intended for deepwater use is described. The Netherlands maritime research institute (Marin) aims to stay at the forefront of offshore research and development with this new facility. Other articles cover pipe tensioning, new large linear winches and innovations in offshore drilling and production. (UK)

Numerical modeling of porosity waves in the Nankai accretionary wedge décollement, Japan: implications for aseismic slip

Science.gov (United States)

Joshi, Ajit; Appold, Martin S.

2017-01-01

Seismic and hydrologic observations of the Nankai accretionary wedge décollement, Japan, show that overpressures at depths greater than ˜2 km beneath the seafloor could have increased to near lithostatic values due to sediment compaction and diagenesis, clay dehydration, and shearing. The resultant high overpressures are hypothesized then to have migrated in rapid surges or pulses called `porosity waves' up the dip of the décollement. Such high velocities—much higher than expected Darcy fluxes—are possible for porosity waves if the porous media through which the waves travel are deformable enough for porosity and permeability to increase strongly with increasing fluid pressure. The present study aimed to test the hypothesis that porosity waves can travel at rates (kilometers per day) fast enough to cause aseismic slip in the Nankai décollement. The hypothesis was tested using a one-dimensional numerical solution to the fluid mass conservation equation for elastic porous media. Results show that porosity waves generated at depths of ˜2 km from overpressures in excess of lithostatic pressure can propagate at rates sufficient to account for aseismic slip along the décollement over a wide range of hydrogeological conditions. Sensitivity analysis showed porosity wave velocity to be strongly dependent on specific storage, fluid viscosity, and the permeability-depth gradient. Overpressure slightly less than lithostatic pressure could also produce porosity waves capable of traveling at velocities sufficient to cause aseismic slip, provided that hydrogeologic properties of the décollement are near the limits of their geologically reasonable ranges.

OUT Success Stories: Solar Trough Power Plants

Science.gov (United States)

Jones, J.

2000-08-01

The Solar Electric Generating System (SEGS) plants use parabolic-trough solar collectors to capture the sun's energy and convert it to heat. The SEGS plants range in capacity from 13.8 to 80 MW, and they were constructed to meet Southern California Edison Company's periods of peak power demand.

Frictional properties of the Nankai frontal thrust explain recurring shallow slow slip events

Science.gov (United States)

Saffer, D. M.; Ikari, M.; Kopf, A.; Roesner, A.

2017-12-01

Recent observations provide evidence for shallow slip reaching to the trench on subduction megathrusts, both in earthquakes and slow slip events (SSE). This is at odds with existing friction studies, which report primarily velocity-strengthening behavior (friction increases with slip velocity) for subduction fault material and synthetic analogs, which leads only to stable sliding. We report on direct shearing experiments on fault rocks from IODP Site C0007, which sampled the frontal thrust of the Nankai accretionary prism. This fault has been implicated in both coseimic slip and recurring SSE. We focus on material from 437.2 meters below seafloor, immediately above a localized shear zone near the base of the fault. In our experiments, a 25 mm diameter cylindrical specimen is loaded in an assembly of two steel plates. After application of normal stress (3, 10, or 17 MPa) and subsequent equilibration, the lower plate is driven at a constant velocity while the upper plate remains stationary; this configuration forces shear to localize between the two plates. After reaching a steady state residual friction coefficient (µss), we conducted velocity-stepping tests to measure the friction rate parameter (a-b), defined as the change in friction for a change in velocity: (a-b) = Δuss/ln(V/Vo), over a range of velocities from 0.1-100 µm s-1. We find that µss ranges from 0.26 to 0.32 and exhibits a slight decrease with normal stress. We observe velocity-weakening behavior at low normal stresses (3-10 MPa) and for low sliding velocities (30 µm s-1. At higher normal stress (17 MPa), we observe dominantly velocity-strengthening, consistent with previously reported measurements for 25 MPa normal stress. Our observation of rate weakening at slip rates matching those of SSE in the outer Nankai forearc provide a potential explanation for periodic strain accumulation and subsequent release during SSE near the trench. The observation of rate weakening behavior only at low normal

Offshoring R&D

DEFF Research Database (Denmark)

Hansen, Zaza Nadja Lee; Rasmussen, Lauge Baungaard

2010-01-01

Companies are increasingly offshoring R&D activities. Many firms, however, experience difficulties related to virtual teamwork across cultures and time zones. The research question is: How does increasing R&D offshoring impact transparency of communication structures and knowledge sharing? Using...... case studies from Danish multinational corporations with R&D activities in China, India or Eastern Europe this paper analyses the impact observed in these companies in regard to communication structures and knowledge sharing in management of offshored R&D activities. The findings show that companies...... attempt to increase transparency through formalisation of knowledge and clear communication structures. However, the influence of tacit knowledge, horizontal communication and culture seem largely overlooked. Therefore the authors suggest a context based approach to transparency accustomed...

Offshore Wind Energy Resource Assessment for Alaska

Energy Technology Data Exchange (ETDEWEB)

Doubrawa Moreira, Paula [National Renewable Energy Lab. (NREL), Golden, CO (United States); Scott, George N. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Musial, Walter D. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Kilcher, Levi F. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Draxl, Caroline [National Renewable Energy Lab. (NREL), Golden, CO (United States); Lantz, Eric J. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2018-01-02

This report quantifies Alaska's offshore wind resource capacity while focusing on its unique nature. It is a supplement to the existing U.S. Offshore Wind Resource Assessment, which evaluated the offshore wind resource for all other U.S. states. Together, these reports provide the foundation for the nation's offshore wind value proposition. Both studies were developed by the National Renewable Energy Laboratory. The analysis presented herein represents the first quantitative evidence of the offshore wind energy potential of Alaska. The technical offshore wind resource area in Alaska is larger than the technical offshore resource area of all other coastal U.S. states combined. Despite the abundant wind resource available, significant challenges inhibit large-scale offshore wind deployment in Alaska, such as the remoteness of the resource, its distance from load centers, and the wealth of land available for onshore wind development. Throughout this report, the energy landscape of Alaska is reviewed and a resource assessment analysis is performed in terms of gross and technical offshore capacity and energy potential.

The Relationship Between Vancomycin Trough Concentrations and AUC/MIC Ratios in Pediatric Patients: A Qualitative Systematic Review.

Science.gov (United States)

Tkachuk, Stacey; Collins, Kyle; Ensom, Mary H H

2018-04-01

In adults, the area under the concentration-time curve (AUC) divided by the minimum inhibitory concentration (MIC) is associated with better clinical and bacteriological response to vancomycin in patients with methicillin-resistant Staphylococcus aureus who achieve target AUC/MIC ≥ 400. This target is often extrapolated to pediatric patients despite the lack of similar evidence. The impracticalities of calculating the AUC in practice means vancomycin trough concentrations are used to predict the AUC/MIC. This review aimed to determine the relationship between vancomycin trough concentrations and AUC/MIC in pediatric patients. We searched the MEDLINE and Embase databases, the Cochrane Database of Systematic Reviews, and the Cochrane Central Register of Controlled Trials using the medical subject heading (MeSH) terms vancomycin and AUC and pediatric* or paediatric*. Articles were included if they were published in English and reported a relationship between vancomycin trough concentrations and AUC/MIC. Of 122 articles retrieved, 11 met the inclusion criteria. One trial reported a relationship between vancomycin trough concentrations, AUC/MIC, and clinical outcomes but was likely underpowered. Five studies found troughs 6-10 mg/l were sufficient to attain an AUC/MIC > 400 in most general hospitalized pediatric patients. One study in patients undergoing cardiothoracic surgery found a trough of 18.4 mg/l achieved an AUC/MIC > 400. Two oncology studies reported troughs ≥ 15 mg/l likely attained an AUC/MIC ≥ 400. In critical care patients: one study found a trough of 9 mg/l did not attain the AUC/MIC target; another found 7 mg/l corresponded to an AUC/MIC of 400. Potential vancomycin targets varied based on the population studied but, for general hospitalized pediatric patients, troughs of 6-10 mg/l are likely sufficient to achieve AUC/MIC ≥ 400. For MIC ≥ 2 mg/l, higher troughs are likely necessary to achieve an AUC/MIC ≥ 400. More

Proceedings of the ENDOW workshop 'Offshore wakes: Measurements and modelling[Efficient Development of Offshore Windfarms

Energy Technology Data Exchange (ETDEWEB)

Barthelmie, R.J. (ed.)

2002-03-01

The papers presented in these Proceedings are the result of a workshop held at Risoe National Laboratory on March 7 and 8 2002 entitled 'Offshore Wakes: Measurements and Modelling'. The Workshop was arranged to showcase results of the European Community supported project 'Efficient Development of Offshore Windfarms (ENDOW)' and featured a series of eight presentations discussing modelling of wakes and boundary layers, existing and new measurements from offshore wind farms and how these will be linked in a new design tool and applied at planned offshore wind farms. In addition seven invited presentations covered a range of relevant topics from analytical approaches to fatigue and extreme loads in wind turbine clusters, current wake modelling in WAsP, optimising power production at Arklow Bank, Particle Image Velocimetry study of a wind turbine wake in a yaw, offshore wind measurements in Massachusetts, accuracy of SODAR measurements for wind energy and tidal influence of offshore wind speeds and turbulence. (au)

Organizational Adaptation in Offshoring

DEFF Research Database (Denmark)

Geisler Asmussen, Christian; Møller Larsen, Marcus; Pedersen, Torben

2016-01-01

Offshoring offers managers the promise of substantial economic benefits, but also comes with the risk of increased complexity and coordination challenges. We argue that offshoring firms must accumulate architectural knowledge to keep the cost of coordination of the geographically separated activi...

Offshore wind development research.

Science.gov (United States)

2014-04-01

Offshore wind (OSW) development is a new undertaking in the US. This project is a response to : New Jerseys 2011 Energy Master Plan that envisions procuring 22.5% of the states power : originating from renewable sources by 2021. The Offshore Wi...

Offshore Fish Community: Ecological Interactions | Science ...

Science.gov (United States)

The offshore (>80 m) fish community of Lake Superior is made up of predominately native species. The most prominent species are deepwater sculpin, kiyi, cisco, siscowet lake trout, burbot, and the exotic sea lamprey. Bloater and shortjaw cisco are also found in the offshore zone. Bloater is abundant in the offshore zone but appears restricted to depths shallower than 150 m (Selgeby and Hoff 1996; Stockwell et al. 2010), although it occuppied greater depths several decades ago (Dryer 1966; Peck 1977). Shortjaw is relatively rare in the offshore zone (Hoff and Todd 2004; Gorman and Hoff 2009; Gorman and Todd 2007). Lake whitefish is also known to frequent bathymetric depths >100 m (Yule et al. 2008b). In this chapter, we develop a conceptual model of the offshore food web based on data collected during 2001-2005 and on inferences from species interactions known for the nearshore fish community. We then develop a framework for examination of energy and nutrient movements within the pelagic and benthic habitats of the offshore zone and across the offshore and nearshore zones. To document research results.

Full parabolic trough qualification from prototype to demonstration loop

Science.gov (United States)

Janotte, Nicole; Lüpfert, Eckhard; Pottler, Klaus; Schmitz, Mark

2017-06-01

On the example of the HelioTrough® collector development the full accompanying and supporting qualification program for large-scale parabolic trough collectors for solar thermal power plants is described from prototype to demonstration loop scale. In the evaluation process the actual state and the optimization potential are assessed. This includes the optical and geometrical performance determined by concentrator shape, deformation, assembly quality and local intercept factor values. Furthermore, its mechanical performance in terms of tracking accuracy and torsional stiffness and its thermal system performance on the basis of the overall thermal output and heat loss are evaluated. Demonstration loop tests deliver results of collector modules statistical slope deviation of 1.9 to 2.6 mrad, intercept factor above 98%, peak optical performance of 81.6% and heat loss coefficients from field tests. The benefit of such a closely monitored development lies in prompt feedback on strengths, weaknesses and potential improvements on the new product at any development stage from first module tests until demonstration loop evaluation. The product developer takes advantage of the achieved technical maturity, already before the implementation in a commercial power plant. The well-understood performance characteristics allow the reduction of safety margins making the new HelioTrough collector competitive from the start.

Offshore Wind Power Planning in Korea

DEFF Research Database (Denmark)

Seo, Chul Soo; Cha, Seung-Tae; Park, Sang Ho

2012-01-01

this possible, Korea has announced the National offshore power roadmap and is now in pursuit. However, large scale offshore wind farms can incur many problems, such as power quality problems, when connecting to a power system.[1][2] Thus, KEPCO is on the process of a research study to evaluate the effects...... that connecting offshore wind power generation to a power system has on the power system. This paper looks over offshore wind power planning in Korea and describes the development of impact assessment technology of offshore wind farms.......Wind power generation is globally recognized as the most universal and reliable form of renewable energy. Korea is currently depending mostly on coal and petroleum to generate electrical power and is now trying to replace them with renewable energy such as offshore wind power generation. To make...

Offshore system for integration of the wind energy; Sistema offshore para integracao de energia eolica

Energy Technology Data Exchange (ETDEWEB)

Decker, Jan de [3E, Brussels (Belgium); Tambke, Jens [Universidade de Oldemburg (Germany). ForWind; Voelker, J. [Dena - Agencia Alema de Energia (Germany); Michalowska-Knap, Katarzyna [Instituto de Energia Renovavel (Poland)

2010-09-15

The Offshore Grid project aims to analyze the conditions required for the development of an offshore transmission network to integrate renewable energy (wind) to the national electrical systems, securely and efficiently. Regulatory aspects, technical, economic and political are considered, that will help the various players in the industry to have a common view on the offshore power grids in Europe.

Use of deep seismic shooting to study graben-like troughs. [Urals

Energy Technology Data Exchange (ETDEWEB)

Makalovskiy, V.V.; Silayev, V.A.

1983-01-01

In the Southeast Perm Oblast, in the zone of articulation of the Russian platform and the Cisural trough, in order to study the structure of the graben-like troughs together with deep drilling, well seismic exploration is used by the method of deep seismic shooting (DSS). The DSS method developed by the Kamskiy department of the VNIGNI consists of blasting in the well shaft and recording of the elastic fluctuations on the Earth's surface. The use of the DSS made it possible to pinpoint structural details of the graben-like trough, and to clarify that this is in essence a zone of fracturing, where the lowered blocks alternated with elevated, and to establish the location and amplitude of the tectonic disorders. High geological information content, low labor intensity and rapidity of obtaining the results make it possible to recommend the DSS together with prospecting and exploratory drilling to study complexly constructed objects in order to reduce the number of unproductive wells.

Balanced Cross Section for Restoration of Tectonic Evolution in the Southwest Okinawa Trough

Institute of Scientific and Technical Information of China (English)

Wu Shiguo; Ni Xianglong; Guo Junhua

2007-01-01

On the basis of the multi-channel seismic data and the other data, using 2DMove software,the tectonic evolution in three seismic profiles was restored since Pliocene. The tectonic restoration results show that: (1) the initial active center lay in the west slope and then was transferred to east and south via trough center during the evolution process; (2) several main normal faults controlled the evolution of the southern Okinawa Trough; (3) since Late Pliocene, the southern Okinawa Trough has experienced two spreading stages. The early is depression in Early-Middle Pleistocene and the late is back-arc spreading in Late Pleistocene and Holocene, which is in primary oceanic crust spreading stage.

A New Coordinated Voltage Control Scheme for Offshore AC Grid of HVDC Connected Offshore Wind Power Plants

DEFF Research Database (Denmark)

Sakamuri, Jayachandra N.; Cutululis, Nicolaos Antonio; Rather, Zakir Hussain

2015-01-01

This paper proposes a coordinated voltage control scheme (CVCS) which enhances the voltage ride through (VRT) capability of an offshore AC grid comprised of a cluster of offshore wind power plants (WPP) connected through AC cables to the offshore voltage source converter based high voltage DC (VSC......-HVDC) converter station. Due to limited short circuit power contribution from power electronic interfaced variable speed wind generators and with the onshore main grid decoupled by the HVDC link, the offshore AC grid becomes more vulnerable to dynamic voltage events. Therefore, a short circuit fault...... in the offshore AC Grid is likely to have significant implications on the voltage of the offshore AC grid, hence on the power flow to the onshore mainland grid. The proposed CVCS integrates individual local reactive power control of wind turbines and of the HVDC converter with the secondary voltage controller...

Submarine Landslides and Mass-Transport Deposition in the Nankai fore-arc

Science.gov (United States)

Strasser, M.; Henry, P.; Kanamatsu, T.; Moe, K.; Moore, G. F.; IODP Expedition 333 Scientists

2011-12-01

Multiple lines of evidence exist for a range of sediment mass movement processes within the shallow megasplay fault zone (MSFZ) area and the adjacent slope basin in the outer fore-arc of the Nankai subduction zone, Japan. Diagnostic features observed in 3-D reflection seismic data and in cores from Integrated Ocean Drilling Program (IODP) Expedition 316 document a complex mass movement history spanning at least ˜2.87 million years. Various modes and scales of sediment remobilization can be related to the different morphotectonic settings in which they occurred and allow integration of knowledge on the spatial and temporal distribution of submarine landslides into a holistic reconstruction of the tectonostratigraphic evolution. New data from the most-recent Nankai IODP Expedition 333, which drilled and cored a Pleistocene-to-Holocene succession of the slope-basin seaward of the MSFZ, provides unprecedented details on submarine landslide processes occurring over the last Million year. The slope-basin represents the depocentre for downslope sediment transport and is characterized in 3-D reflection seismic data by several mass-transport deposits (MTDs), including an up to 180 m thick MTD. Here we present D/V Chikyu shipboard results and first post cruise results from Site C0018, including litho- bio- magneto- tephra- and stable isotope-stratigraphy, X-ray computed tomography analysis and physical properties data. Six MTDs were identified from visual core description and X-ray CT-scans. The thickest MTD is also the oldest (emplaced between 0.85 and 1.05 Ma) and it coincides with a lithological transition between a sandy turbidite sequence below, and ash-bearing hemipelagites comprising several MTDs above. Deformation styles within the MTD are heterogeneous: intervals of disturbed sediments are interbedded within intervals inferred to retain original, coherent bedding. In three occurrences the base of the MTD is defined by a shear zone within fine-grained sediments

Offshore concrete structures

International Nuclear Information System (INIS)

Lamas Pardo, M.; Carral Couce, L. M.

2011-01-01

In the offshore industry there are two possible materials for the construction of the hull of a structure; the steel and concrete, with the first one widely used until now, as in the rest of the shiphuidling industry of merchant ships, warships, etc. Materials such as aluminum, GRP or timber areused in small units with lengths lower than 100 m, and in less adverse conditions than in the offshore industry. Nevertheless, some ships/barges have been built of concrete in the past, but have been rather isolated cases which have not changed the practice in the industry. In the First and Second World War were built by the scarcity of materials, while the series of barges by Alfred A. Yee was a rare exception. Other units were also made in concrete, but almost anecdotal. Still, the behaviour of these concrete structures, especially in terms of maintenance, has been excellent. Therefore, the fact that the concrete has not had an adequate reception so far in shipbuilding, does not mean that in will not be the material best suited for the offshore industry in the future. The extra displacement and associated fuel costs in concrete ships have been found prohibitive in the past. But the loss of mobility of a concrete hull in relation to a steel hull can be perfectly offset by the advantages offered by the concrete, as the shipping and offshore industry have very different priorities. One of the main differences in these priorities is in terms of maintenance and resistance to fatigue, precisely where the concrete performs better. ships can easily be dry docked for maintenance and repair, while in the offshore platforms these works have to be done in situ so maintenance and fatigue are crucial to them. Besides these, the concrete has other advantages according to findings of several studies. And although they are interested in the conclusions that the makes as they came from people in the concrete industry, the fact that in recent years concrete offshore unit shave been built

Offshore Wind Market and Economic Analysis

Energy Technology Data Exchange (ETDEWEB)

Hamilton, Bruce Duncan [Navigant Consulting, Inc., Chicago, IL (United States)

2014-08-27

This report is the third annual assessment of the U.S. offshore wind market. It includes the following major sections: Section 1: key data on developments in the offshore wind technology sector and the global development of offshore wind projects, with a particular focus on progress in the United States; Section 2: analysis of policy developments at the federal and state levels that have been effective in advancing offshore wind deployment in the United States; Section 3: analysis of actual and projected economic impact, including regional development and job creation; Section 4: analysis of developments in relevant sectors of the economy with the potential to affect offshore wind deployment in the United States

Import, Offshoring and Wages

DEFF Research Database (Denmark)

Fosse, Henrik Barslund; Maitra, Madhura

Offshoring firms are found to pay higher average wages than purely domestic firms. We provide a unifying empirical approach by capturing the different channels through which offshoring may explain this wage difference: (i) due to change in the composition of workers (skill composition effect) (ii......) because all existing workers get higher pay (rent sharing effect). Using Danish worker-firm data we explain how much each channel contributes to higher wages. To estimate the causal effect of offshoring on wages we use China’s accession to the WTO in December 2001 - and the soon after boom in Chinese...

The economics of offshore wind

International Nuclear Information System (INIS)

Green, Richard; Vasilakos, Nicholas

2011-01-01

This paper presents an overview of the main issues associated with the economics of offshore wind. Investment in offshore wind systems has been growing rapidly throughout Europe, and the technology will be essential in meeting EU targets for renewable energy in 2020. Offshore wind suffers from high installation and connection costs, however, making government support essential. We review various support policies used in Europe, concluding that tender-based feed-in tariff schemes, as used in Denmark, may be best for providing adequate support while minimising developers' rents. It may prove economic to build an international offshore grid connecting wind farms belonging to different countries that are sited close to each other. (author)

The economics of offshore wind

Energy Technology Data Exchange (ETDEWEB)

Green, Richard; Vasilakos, Nicholas [Department of Economics, University of Birmingham, Birmingham B15 2TT (United Kingdom)

2011-02-15

This paper presents an overview of the main issues associated with the economics of offshore wind. Investment in offshore wind systems has been growing rapidly throughout Europe, and the technology will be essential in meeting EU targets for renewable energy in 2020. Offshore wind suffers from high installation and connection costs, however, making government support essential. We review various support policies used in Europe, concluding that tender-based feed-in tariff schemes, as used in Denmark, may be best for providing adequate support while minimising developers' rents. It may prove economic to build an international offshore grid connecting wind farms belonging to different countries that are sited close to each other. (author)

NREL Offshore Balance-of-System Model

Energy Technology Data Exchange (ETDEWEB)

Maness, Michael [National Renewable Energy Lab. (NREL), Golden, CO (United States); Maples, Benjamin [National Renewable Energy Lab. (NREL), Golden, CO (United States); Smith, Aaron [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2017-01-01

The U.S. Department of Energy (DOE) has investigated the potential for 20% of nationwide electricity demand to be generated from wind by 2030 and, more recently, 35% by 2050. Achieving this level of wind power generation may require the development and deployment of offshore wind technologies. DOE (2008) has indicated that reaching these 2030 and 2050 scenarios could result in approximately 10% and 20%, respectively, of wind energy generation to come from offshore resources. By the end of 2013, 6.5 gigawatts of offshore wind were installed globally. The first U.S. project, the Block Island Wind Farm off the coast of Rhode Island, has recently begun operations. One of the major reasons that offshore wind development in the United States is lagging behind global trends is the high capital expenditures required. An understanding of the costs and associated drivers of building a commercial-scale offshore wind plant in the United States will inform future research and help U.S. investors feel more confident in offshore wind development. In an effort to explain these costs, the National Renewable Energy Laboratory has developed the Offshore Balance-of-System model.

Offshore wind energy. An overview on the activities in Germany; Offshore-Windenergie. Ein Ueberblick ueber die Aktivitaeten in Deutschland

Energy Technology Data Exchange (ETDEWEB)

Worm, Anja [media consulta Deutschland GmbH, Berlin (Germany)

2013-02-15

The brochure under consideration provides an overview of the activities of offshore wind energy in Germany. The first offshore wind farms are built and generate more electricity than expected. The offshore wind farms serve as a field of learning for new technologies. The power of offshore wind farms opened new prospects for the economy. The northern Federal States of Germany as well as the traditional locations for mechanical engineering and steel production benefit from offshore wind energy.

Deep drivers of mesoscale circulation in the central Rockall Trough

Science.gov (United States)

Sherwin, T. J.; Alyenik, D.; Dumont, E.; Inall, M.

2014-11-01

Mesoscale variability in the central Rockall Trough between about 56 and 58° N has been investigated using a combination of ship-borne, underwater glider and gridded satellite altimeter measurements. Altimeter observations show that mesoscale features such as eddies and large scale circulation cells are ubiquitous phenomena. They have horizontal length scales of order 100 km with vertical scales of over 1000 m and are associated with mean current speeds (over the upper 1000 m) of 15 ± 7 cm s-1. Monthly area averaged surface Eddy Kinetic Energy (EKE) has substantial inter-annual variability, which at times can dominate a mean seasonal signal that varies from a maximum in May (74 cm2 s-2) to a minimum in October (52 cm2 s-2) and has increased gradually since 1992 at about 1.1 cm2 s-2 per year. A five month glider mission in the Trough showed that much of this energy comes from features that are located over 1000 m below the surface in the deep cold waters of the Trough (possibly from eddies associated the North Atlantic Current). The surface currents from altimeters had similar magnitude to the drift currents averaged over 1000 m from the glider in the stratified autumn, but were half the deep water speed during late winter. Although the mesoscale features move in an apparent random manner they may also be quasi-trapped by submarine topography such as seamounts. Occasionally anti-cyclonic and cyclonic cells combine to cause a coherent westward deflection of the European slope current that warms the Rockall side of the Trough. Such deflections contribute to the inter-annual variability in the observed temperature and salinity that are monitored in the upper 800 m of the Trough. By combining glider and altimeter measurements it is shown that altimeter measurements fail to observe a 15 cm s-1 northward flowing slope current on the eastern side and a small persistent southward current on the western side. There is much to be gained from the synergy between satellite

Danish offshore wind - Key environmental issues

International Nuclear Information System (INIS)

2006-11-01

Danish experience from the past 15 years shows that offshore wind farms, if placed right, can be engineered and operated without significant damage to the marine environment and vulnerable species. The comprehensive environmental monitoring programmes of Horns Rev Offshore Wind Farm and Nysted Offshore Wind Farm confirm that, under the rieght conditions, even big wind farms pose low risk to birds, mammals and fish, even though there will be changes in the living conditions of some species by an increase in habitat heterogeneity. The monitoring also shows that appropriate siting of offshore wind farms is an essential precondition for ensuring limited impact on nature and the environment, and that careful spatial planning is necessary to avoid damaging cumulative impacts. Due consideration to limiting the impacts on nature together with positive attitudes towards offshore wind farms in local communities and challenging energy policy objectives at national and international levels mean that prospects look bright for future offshore expansion. (au)

Offshore Outsourcing

DEFF Research Database (Denmark)

Petersen, Bent; Benito, Gabriel R. G.; Dovgan, Olesya

While the extant literature on offshore outsourcing deals with this operation mode in isolation, and typically with a focus on cost effects, we address the broader question of how companies choose and use outsourcing as part of foreign operation mode development and as a contributor to internatio...... that outsourcing can be used proactively to promote expanded international operations.......While the extant literature on offshore outsourcing deals with this operation mode in isolation, and typically with a focus on cost effects, we address the broader question of how companies choose and use outsourcing as part of foreign operation mode development and as a contributor...

Optical and mechanical tolerances in hybrid concentrated thermal-PV solar trough.

Science.gov (United States)

Diaz, Liliana Ruiz; Cocilovo, Byron; Miles, Alexander; Pan, Wei; Blanche, Pierre-Alexandre; Norwood, Robert A

2018-05-14

Hybrid thermal-PV solar trough collectors combine concentrated photovoltaics and concentrated solar power technology to harvest and store solar energy. In this work, the optical and mechanical requirements for optimal efficiency are analyzed using non-sequential ray tracing techniques. The results are used to generate opto-mechanical tolerances that can be compared to those of traditional solar collectors. We also explore ideas on how to relieve tracking tolerances for single-axis solar collectors. The objective is to establish a basis for tolerances required for the fabrication and manufacturing of hybrid solar trough collectors.

2016 Offshore Wind Market Report

Energy Technology Data Exchange (ETDEWEB)

Musial, Walter [National Renewable Energy Lab. (NREL), Golden, CO (United States); Beiter, Philipp [National Renewable Energy Lab. (NREL), Golden, CO (United States); Schwabe, Paul [National Renewable Energy Lab. (NREL), Golden, CO (United States); Tian, Tian [National Renewable Energy Lab. (NREL), Golden, CO (United States); Stehly, Tyler [National Renewable Energy Lab. (NREL), Golden, CO (United States); Spitsen, Paul [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2017-08-07

The 2016 Offshore Wind Technologies Market Report is intended to provide stakeholders with quantitative information about the offshore wind market, technology, and cost trends in the United States and worldwide.

Paleoceanographic records in the sedimentary cores from the middle Okinawa Trough

Institute of Scientific and Technical Information of China (English)

无

2003-01-01

Two gravity piston cores (Cores 155 and 180) involved in this study were collected from the middle Okinawa Trough. Stratigraphy of the two cores was divided and classified based on the features of planktonic foraminifera oxygen isotope changes together with depositional sequence, millennium-scale climatic event comparison, carbonate cycles and AMS14C dating. Some paleoclimatic information contained in sediments of these cores was extracted to discuss the paleoclimatic change rules and the short-time scale events presented in interglacial period. Analysis on the variation of oxygen isotope values in stage two shows that the middle part of the Okinawa Trough may have been affected by fresh water from the Yellow River and the Yangtze River during the Last Glacial Maximum (LGM). The oxygen isotope value oscillating ranges of the cores have verified that the marginal sea has an amplifying effect on climate changes. The Δ13c of benthic foraminifera Uvigerina was lighter in the glacial period than that in the interglacial period, which indicates that the Paleo-Kuroshio's main stream moved eastward and its influence area decreased. According to the temperature difference during the "YD" period existing in Core 180 and other data, we can reach the conclusion that the climatic changes in the middle Okinawa Trough area were controlled by global climatic changes, but some regional factors had also considerable influence on the climate changes. Some results in this paper support Fairbanks's point that the "YD" event was a brief stagnation of sea level rising during the global warming up procession. Moreover, the falling of sea level in the glacial period weakened the exchange between the bottom water of the Okinawa Trough and the deep water of the northwestern Pacific Ocean and resulted in low oxygen state of bottom water in this area. These procedures are the reasons for carbonate cycle in the Okinawa Trough area being consistent with the "Atlantic type " carbonate cycle.

Paleoceanographic records in the sedimentary cores from the middle Okinawa Trough

Institute of Scientific and Technical Information of China (English)

LIUYanguang; FUYunxia; DUDewen; MENGXianwei; LIANGRuicai; LITiegang; WUShiying

2003-01-01

Two gravity piston cores (Cores 155 and 180) involved in this study were collected from the middle Okinawa Trough. Stratigraphy of the two cores was divided and classified based on the features of planktonic foraminifera oxygen isotope changes together with depositional sequence,millennium-scale climatic event comparison, carbonate cycles and AMS14C dating. Some paleoclimatic information contained in sediments of these cores was extracted to discuss the paleoclimatic change rules and the short-time scale events presented in interglacial period. Analysis on the variation of oxygen isotope values in stage two shows that the middle part of the Okinawa Trough may have been affected by fresh water from the Yellow River and the Yangtze River during the Last Glacial Maximum (LGM). The oxygen isotope value oscillating ranges of the cores have verified that the marginal sea has an amplifying effect on climate changes.The δ13C of benthic foraminifera Uvigerina was lighter in the glacial period than that in the interglacial period, which indicates that the Paleo-Kuroshio's main stream moved eastward and its influence area decreased. According to the temperature difference during the “YD” period existing in Core 180 and other data, we can reach the conclusion that the climatic changes in the middle Okinawa Trough area were controlled by global climatic changes, but some regional factors had also considerable influence on the climatechanges. Some results in this paper support Fairbanks's point that the “YD” event was a brief stagnation of sea level rising during the global warming up procession. Moreover,the falling of sea level in the glacial period weakened the exchange between the bottom water of the Okinawa Trough and the deep water of the northwestern Pacific Ocean and resulted in low oxygen state of bottom water in this area.These procedures are the reasons for carbonate cycle in the Okinawa Trough area being consistent with the “Atlantic type”carbonate cycle.

CFD for wind and tidal offshore turbines

CERN Document Server

Montlaur, Adeline

2015-01-01

The book encompasses novel CFD techniques to compute offshore wind and tidal applications. Computational fluid dynamics (CFD) techniques are regarded as the main design tool to explore the new engineering challenges presented by offshore wind and tidal turbines for energy generation. The difficulty and costs of undertaking experimental tests in offshore environments have increased the interest in the field of CFD which is used to design appropriate turbines and blades, understand fluid flow physical phenomena associated with offshore environments, predict power production or characterise offshore environments, amongst other topics.

Energy from Offshore Wind: Preprint

Energy Technology Data Exchange (ETDEWEB)

Musial, W.; Butterfield, S.; Ram, B.

2006-02-01

This paper provides an overview of the nascent offshore wind energy industry including a status of the commercial offshore industry and the technologies that will be needed for full market development.

Utilizing offshore potentials for wind power generation; Nutzung der Offshore-Potentiale fuer die Windenergie

Energy Technology Data Exchange (ETDEWEB)

Hannemann, H. [Neptun Industrie GmbH, Rostock (Germany)

2000-07-01

The contribution discusses the importance of the offshore market and recommends measures to develop it. A turnkey offer is required for exports, which means that all organisations cooperating in the pilot project must prove their competence. The status of a pilot project in the Baltic Sea and the further plans for the park (20 systems, 40 MW, more than 10 km off the coast, water depth about 20 m) are reviewed. [German] Zur Erschliessung des Offshore - Marktes fuer Windenergieanlagen ist es erforderlich, die Technologie ''vor der eigenen Haustuer'' demonstrieren zu koennen. Nach einer Betrachtung der europaeischen Offshore - Windenergie - Potentiale und der davon moeglicherweise nutzbaren Anteile wird die Bedeutung des Offshore - Marktes deutlich. Besonders fuer die Hersteller ist der Offshore - Markt fuer den langfristigen Export von besonderer Bedeutung. Um den Export zu realisieren, ist ein Turnkey - Angebot erforderlich, so dass im Pilotprojekt alle an der gesamten Realisation beteiligten Organisationen ihre Kompetenz beweisen muessen und koennen. Der Stand eines Pilotprojektes in der Ostsee und die weitere Planung fuer den Park (20 Anlagen, 40 MW, >10 km Kuestenentfernung, ca. 20 m Wassertiefe) wird dargestellt. (orig.)

Modeling, Simulation and Performance Evaluation of Parabolic Trough

African Journals Online (AJOL)

Mekuannint

Mekuannint Mesfin and Abebayehu Assefa. Department of Mechanical Engineering. Addis Ababa University ... off design weather conditions as well. Keywords: Parabolic Trough Collector (PTC);. Heat Transfer ... of a conventional Rankine cycle power plant with solar fields that are used to increase the temperature of heat ...

Modeling, Simulation and Performance Evaluation of Parabolic Trough

African Journals Online (AJOL)

Mekuannint

Heat Transfer Fluid (HTF); TRNSYS power plant model; STEC library; Solar Advisor Model (SAM);. TRNSYS solar field model; Solar Electric. Generation System (SEGS). INTRODUCTION. Parabolic troughs are currently most used means of power generation option of solar sources. Solar electric generation systems (SEGs) ...

Optical analysis of a photovoltaic V-trough system installed in western India.

Science.gov (United States)

Maiti, Subarna; Sarmah, Nabin; Bapat, Pratap; Mallick, Tapas K

2012-12-20

The low concentrating photovoltaic (PV) system such as a 2× V-trough system can be a promising choice for enhancing the power output from conventional PV panels with the inclusion of thermal management. This system is more attractive when the reflectors are retrofitted to the stationary PV panels installed in a high aspect ratio in the north-south direction and are tracked 12 times a year manually according to preset angles, thus eliminating the need of diurnal expensive tracking. In the present analysis, a V-trough system facing exactly the south direction is considered, where the tilt angle of the PV panels' row is kept constant at 18.34°. The system is installed on the terrace of CSIR-Central Salt and Marine Chemicals Research Institute in Bhavnagar, Gujarat, India (21.47 N, 71.15 E). The dimension of the entire PV system is 9.64 m×0.55 m. The V-troughs made of anodized aluminum reflectors (70% specular reflectivity) had the same dimensions. An in-house developed; experimentally validated Monte Carlo ray-trace model was used to study the effect of the angular variation of the reflectors throughout a year for the present assembly. Results of the ray trace for the optimized angles showed the maximum simulated optical efficiency to be 85.9%. The spatial distribution of solar intensity over the 0.55 m dimension of the PV panel due to the V-trough reflectors was also studied for the optimized days in periods that included solstices and equinoxes. The measured solar intensity profiles with and without the V-trough system were used to calculate the actual optical efficiencies for several sunny days in the year, and results were validated with the simulated efficiencies within an average error limit of 10%.

The De Long Trough: a newly discovered glacial trough on the East Siberian continental margin

Directory of Open Access Journals (Sweden)

M. O'Regan

2017-09-01

Full Text Available Ice sheets extending over parts of the East Siberian continental shelf have been proposed for the last glacial period and during the larger Pleistocene glaciations. The sparse data available over this sector of the Arctic Ocean have left the timing, extent and even existence of these ice sheets largely unresolved. Here we present new geophysical mapping and sediment coring data from the East Siberian shelf and slope collected during the 2014 SWERUS-C3 expedition (SWERUS-C3: Swedish – Russian – US Arctic Ocean Investigation of Climate-Cryosphere-Carbon Interactions. The multibeam bathymetry and chirp sub-bottom profiles reveal a set of glacial landforms that include grounding zone formations along the outer continental shelf, seaward of which lies a  >  65 m thick sequence of glacio-genic debris flows. The glacial landforms are interpreted to lie at the seaward end of a glacial trough – the first to be reported on the East Siberian margin, here referred to as the De Long Trough because of its location due north of the De Long Islands. Stratigraphy and dating of sediment cores show that a drape of acoustically laminated sediments covering the glacial deposits is older than ∼ 50 cal kyr BP. This provides direct evidence for extensive glacial activity on the Siberian shelf that predates the Last Glacial Maximum and most likely occurred during the Saalian (Marine Isotope Stage (MIS 6.

Wind energy in offshore grids

Energy Technology Data Exchange (ETDEWEB)

Schroeder, S.T.

2013-01-15

This cumulative PhD thesis deals with wind integration in offshore grids from an economic point of view. It is composed of a generic part and eight papers. As the topic has mostly been analysed with a focus on topology and technical issues until now, market-operational questions in offshore grids and investment implications under different regulatory frameworks are a hitherto underrepresented research field. They are addressed by this thesis. Offshore grids between several countries combine the absorption of wind energy with international power trading. However, the inclusion into an offshore grid affects the economics of an offshore wind park. It is shown that the spot market income is lower if an offshore wind farm is placed in an interconnector and subject to nodal pricing instead of having a national affiliation. Moreover, congestion in the interconnector can prevent the wind farm from correcting its wind forecast errors in a specific onshore balancing group. An analytical approach with a transmission system operator and a wind farm as stakeholders illustrates resulting incentives for strategic behaviour. Depending on the regulatory regime, they may be inclined to announce more or less generation than expected at the closure of the day-ahead spot market. This can lead to a suboptimal utilisation of the infrastructure and associated socio-economic losses. These and possibly undesired reallocative effects between the parties can be avoided if the regulatory regime is adjusted to reflect special characteristics of offshore grids. With an operational real options approach, it is furthermore illustrated how different support schemes and connections to additional countries affect the investment case of an offshore wind farm and the income of the transmission system operator. The investment framework has also been addressed with a policy study about possible combinations of support schemes and international cooperation mechanisms between countries to achieve their

IS OFFSHORING AN INTERNATIONAL PROCESS

Directory of Open Access Journals (Sweden)

Paulo Roberto Gião

2012-01-01

Full Text Available This article proposes to analyze the applicability of transaction cost economics - TCE (Coase, 1937; Williamson, 1975, 1979 through its characteristic make-or-buy expression, considering the offshoring pace and emerging economy firms. The make-or-buy decision must be flexible enough to explain offshoring characteristics and developed and emerging economy firms scenarios. As secondary objectives, and to show the trail to the main purpose, two research questions were identified and discussed during the paper: Is offshoring process an international movement only from developed countries to emerging economies? Is the main reason of offshoring the looking for low-cost work / activities? To achieve the proposed objectives, the structure of this paper begins with a reasonable or acceptable definition of offshoring. Some reasons (or “the reason” for the process are also another important starting point. The majority of articles referee the idea that low-cost is the main reason for offshoring, and if it is correct, transaction cost economics seems to be a good basis for our analysis purpose and integrative intention. Also some literature connections between offshoring and TCE are presented and, naturally TCE is presented in highlights for understanding these connections. Ending this section, some different arguments based on newer researches are presented by some authors presenting another perspective as the main reason. After this theoretical approach, a scenario analysis and some discussions are presented based on all possible interactions among firm from developed (DC and emerging economies (EE and examples of international corporations are presented to clarify and improve the understanding of our research questions and to build new contributions to international business theory.

The Economic Geography of Offshoring

DEFF Research Database (Denmark)

Ørberg Jensen, Peter D.; Pedersen, Torben

2011-01-01

when distinguishing between standardized and advanced activities. Asia attracts as many advanced activities as Western Europe while North America attracts more advanced activities even in manufacturing. Central and Eastern Europe attract offshoring in manufacturing and IT, but the activities...... that are offshored to these regions are typically not advanced. One important theoretical implication of this study is that a more detailed understanding of the nature of offshored activities is needed, since such attributes appear to be an important determinant of location choice....

Seismic stratigraphic architecture of the Disko Bay trough-mouth fan system, West Greenland

Science.gov (United States)

Hofmann, Julia C.; Knutz, Paul C.

2015-04-01

Spatial and temporal changes of the Greenland Ice Sheet on the continental shelf bordering Baffin Bay remain poorly constrained. Then as now, fast-flowing ice streams and outlet glaciers have played a key role for the mass balance and stability of polar ice sheets. Despite their significance for Greenland Ice Sheet dynamics and evolution, our understanding of their long-term behaviour is limited. The central West Greenland margin is characterized by a broad continental shelf where a series of troughs extend from fjords to the shelf margin, acting as focal points for trough-mouth fan (TMF) accummulations. The sea-ward bulging morphology and abrupt shelf-break of these major depositional systems is generated by prograding depocentres that formed during glacial maxima when ice streams reached the shelf edge, delivering large amounts of subglacial sediment onto the continental slope (Ó Cofaigh et al., 2013). The aim of this study is to unravel the seismic stratigraphic architecture and depositional processes of the Disko Bay TMF, aerially the largest single sedimentary system in West Greenland, using 2D and 3D seismic reflection data, seabed bathymetry and stratigraphic information from exploration well Hellefisk-1. The south-west Disko Bay is intersected by a deep, narrow trough, Egedesminde Dyb, which extends towards the southwest and links to the shallower and broader cross-shelf Disko Trough (maximum water depths of > 1000 m and a trough length of c. 370 km). Another trough-like depression (trough length of c. 120 km) in the northern part of the TMF, indicating a previous position of the ice stream, can be distinguished on the seabed topographic map and the seismic images. The Disko Bay TMF itself extends from the shelf edge down to the abyssal plain (abyssal floor depths of 2000 m) of the southern Baffin Bay. Based on seismic stratigraphic configurations relating to reflection terminations, erosive patterns and seismic facies (Mitchum et al., 1977), the TMF

Offshore atomic power plants

International Nuclear Information System (INIS)

Anon.

1975-01-01

Various merits of offshore atomic power plants are illustrated, and their systems are assessed. The planning of the offshore atomic power plants in USA is reviewed, and the construction costs of the offshore plant in Japan were estimated. Air pollution problem may be solved by the offshore atomic power plants remarkably. Deep water at low temperature may be advantageously used as cooling water for condensers. Marine resources may be bred by building artificial habitats and by providing spring-up equipments. In the case of floating plants, the plant design can be standardized so that the construction costs may be reduced. The offshore plants can be classified into three systems, namely artificial island system, floating system and sea bottom-based system. The island system may be realized with the present level of civil engineering, but requires the development of technology for the resistance of base against earthquake and its calculation means. The floating system may be constructed with conventional power plant engineering and shipbuilding engineering, but the aseismatic stability of breakwater may be a problem to be solved. Deep water floating system and deep water submerging system are conceivable, but its realization may be difficult. The sea bottom-based system with large caissons can be realized by the present civil engineering, but the construction of the caissons, stability against earthquake and resistance to waves may be problems to be solved. The technical prediction and assessment of new plant sites for nuclear power plants have been reported by Science and Technology Agency in 1974. The construction costs of an offshore plant has been estimated by the Ministry of International Trade and Industry to be yen71,026/kW as of 1985. (Iwakiri, K.)

Offshoring and Changes in Firms’ Domestic Employment

DEFF Research Database (Denmark)

Timmermans, Bram; Østergaard, Christian Richter

difference on a set of employment characteristics, i.e. employment growth, growth in high skilled employees, and growth in employees with a background in science and engineering, by using a partial propensity score matching approach. The findings of the analyses show that there are clear differences between......In this paper, we investigate, by merging the Danish linked employer-employee database with a Danish offshoring survey, the difference in employment between offshoring and non-offshoring firms that are active in manufacturing industries and business services in Denmark. We measure the mean...... Danish offshoring and non-offshoring firms in how the employee composition changes over time. The change in employment composition differ considerably between manufacturing industries and business services and on whether firms offshore administrative and technical business functions or other types...

NEW OFFSHORE LOCATIONS IN THE EUROPEAN UNION

Directory of Open Access Journals (Sweden)

RADULESCU IRINA GABRIELA

2014-05-01

Full Text Available The offshore activity provides benefits for the host market and has positive effects on services, and on producers that use intermediate services. FDI in services has an important impact on the offshore activity, especially through transfer of technology. Many transnational companies have recognized the advantages of offshoring and the fact that it becomes a key globalization force. Recently, the Central European countries have become popular destinations among offshoring

Noise from offshore wind turbines

Energy Technology Data Exchange (ETDEWEB)

Soendergaard, B.; Plovsing, B.

2005-07-01

Noise assessment of wind turbines through calculations is based on sound power levels measured according to e.g. IEC 61400-11. With larger wind turbines and distances some of the calculation models give erroneous results. Noise propagation over water is different from propagation over land. For that reason it is important be able to make valid noise assessments for offshore wind farms. A suggestion for an offshore measurement method is described and a survey of models for noise propagation offshore has been made. (au)

Radiometric evidence of Middle Devonian inversion of the Hill End Trough, northeast Lachlan Fold Belt

International Nuclear Information System (INIS)

Pakham, G.H.

1999-01-01

The publication of a new geological time-scale by the Australian Geological Survey Organisation and radiometric dates from the Hill End goldfield have prompted the re-examination of the timing of deformation of the Hill End Trough to determine whether it occurred in Middle Devonian or Early Carboniferous time. Palaeontological evidence from the western trough margin and the Capertee High dates the end of deposition in the trough as late Emsian or early Eifelian (385-382 Ma). After a mid-Devonian hiatus of at least 15 million years, paralic sedimentation commenced on the Molong and Capertee Highs in late Frasnian or early Famennian time (367-363 Ma). No Upper Devonian sedimentary formations occur in the Hill End Trough. Structural relationships indicate that the oldest mineral veins at Hill End preceded cleavage formation in the deformed trough sedimentary rocks. Early vein muscovites have Middle Devonian 40 Ar/ 39 Ar dates of 380-370 Ma. Regional metamorphic biotites from Hill End have well constrained 40 Ar/ 39 Ar closing ages of 360-358 Ma (mid-Famennian). The metamorphic (thermal) maximum which outlasted penetrative deformation. is estimated here by modelling to have been about 370 Ma (latest Givetian). This clearly places the earlier main deformation in the Middle Devonian. Deformation probably began by terminating trough deposition in latest Emsian to early Eifelian time and ended in early Givetian time at about 375 Ma ago. Published pressure and temperature data from the Hill End goldfield suggest that deformation thickened the 6 km sediment column to around 11 km. The thermal model suggests there was post-deformation erosion of about 4km and little if any further erosion occurred during Late Devonian to Early Carboniferous time. The shortening accompanying the inversion of the northern Hill End Trough may have been taken up in the region to the south, both east and west of the Copperhannia Thrust, and east of the southern termination of the Capertee High

Some characteristics of offshore operations

Directory of Open Access Journals (Sweden)

Popov Đorđe

2011-01-01

Full Text Available Offshore operations are not on the margins of the world economy. They are an integral part of modern business practice. They have become one of the most important instruments in the contemporary globalized financial system. Offshore operations and tax havens are not only conduits for tax avoidance and evasion but belong more broadly to the world of finance, for the business of managing the monetary resources of an organization, country or individuals. Offshore business operating in tax havens is at the heart of a particular type of globalization that is characterized by a growing gap between the very rich and everyone else. Tax havens are financial conduits that, in exchange for a fee, use their one principal asset- their sovereignty to serve a nonresident constituency of accountants and lawyers, bankers and financiers, who bring a demand for offshore operations.

Learning Paths to Offshore Outsourcing

DEFF Research Database (Denmark)

Maskell, Peter; Pedersen, Torben; Petersen, Bent

A corporation’s offshore outsourcing may be seen as the result of a discrete, strategic decision taken in response to an increasing pressure from worldwide competition. However, empirical evidence of a representative cross-sector sample of international Danish firms indicates that offshore sourcing...... in low-cost countries is best described as a learning-by-doing process in which the offshore outsourcing of a corporation goes through a sequence of stages towards sourcing for innovation. Initially, a corporation’s outsourcing is driven by a desire for cost minimization. Over a period of time...... the outsourcing experience lessens the cognitive limitations of decision-makers as to the advantages that can be achieved through outsourcing in low-cost countries: the insourcer/vendor may not only offer cost advantages, but also quality improvement and innovation. The quality improvements that offshore...

Offshore Wind Turbine Foundation Design

OpenAIRE

Passon, Patrik; Branner, Kim; Larsen, Søren Ejling; Hvenekær Rasmussen, Jørgen

2015-01-01

Offshore vindenergi er i høj grad modnet i det seneste årti med en årligt installeret kapacitet på mere end1 GW. En vigtig faktor for den videre udvikling af offshore vindenergi i stor målestok, er en reduktion af de samlede udgifter til produceret energi. I betragtning af for eksempel faldet i olieprisen siden sommeren 2014 og dens fortsatte fald ind i 2015, er det endnu vigtigere at sænke omkostningerne til etablering af vedvarende energikilder såsom offshore vindenergi, for at nå frem til ...

Disaster mitigation science for Earthquakes and Tsunamis -For resilience society against natural disasters-

Science.gov (United States)

Kaneda, Y.; Takahashi, N.; Hori, T.; Kawaguchi, K.; Isouchi, C.; Fujisawa, K.

2017-12-01

Destructive natural disasters such as earthquakes and tsunamis have occurred frequently in the world. For instance, 2004 Sumatra Earthquake in Indonesia, 2008 Wenchuan Earthquake in China, 2010 Chile Earthquake and 2011 Tohoku Earthquake in Japan etc., these earthquakes generated very severe damages. For the reduction and mitigation of damages by destructive natural disasters, early detection of natural disasters and speedy and proper evacuations are indispensable. And hardware and software developments/preparations for reduction and mitigation of natural disasters are quite important. In Japan, DONET as the real time monitoring system on the ocean floor is developed and deployed around the Nankai trough seismogenic zone southwestern Japan. So, the early detection of earthquakes and tsunamis around the Nankai trough seismogenic zone will be expected by DONET. The integration of the real time data and advanced simulation researches will lead to reduce damages, however, in the resilience society, the resilience methods will be required after disasters. Actually, methods on restorations and revivals are necessary after natural disasters. We would like to propose natural disaster mitigation science for early detections, evacuations and restorations against destructive natural disasters. This means the resilience society. In natural disaster mitigation science, there are lots of research fields such as natural science, engineering, medical treatment, social science and literature/art etc. Especially, natural science, engineering and medical treatment are fundamental research fields for natural disaster mitigation, but social sciences such as sociology, geography and psychology etc. are very important research fields for restorations after natural disasters. Finally, to realize and progress disaster mitigation science, human resource cultivation is indispensable. We already carried out disaster mitigation science under `new disaster mitigation research project on Mega

Development of Offshore Wind Power Industry

Institute of Scientific and Technical Information of China (English)

Liu Xiao

2011-01-01

The offshore wind power development target as initially proposed in "The 12=Five-Year" on energy recourses development and renewable energy recourses currently under development is to reach 5m KW by 2015 and 30m KW by 2020. With the unfolding of offshore wind turbine planning from different areas, the curtain of offshore wind power development for our country's "The 12=Five-Year" has been opened.

Managing Risk Areas in Software Development Offshoring

DEFF Research Database (Denmark)

Persson, John Stouby; Schlichter, Bjarne Rerup

2015-01-01

Software companies are increasingly offshoring development to countries with high expertise at lower cost. Offshoring involves particular risk areas that if ignored increase the likelihood of failure. However, the offshoring client’s maturity level may influence the management of these risk areas...

The effects of meshed offshore grids on offshore wind investment – a real options analysis

DEFF Research Database (Denmark)

Schröder, Sascha Thorsten; Kitzing, Lena

2012-01-01

Offshore wind farms in future meshed offshore grids could be subject to different regulatory regimes. Feed-in tariffs would absorb market risk from wind farm operators, whereas price premium mechanisms leave operators exposed to market price signals. In this case, it plays a decisive role which...... price applies to a node in an offshore grid. The offshore node will either be integrated into any of the neighbouring markets, with access to the respective maximum price, or be subject to separate nodal pricing. We investigate the different regulatory regimes for connections to one to four countries...... based on a stochastic model capturing uncertainties in prices and line failures. The stochastic analysis shows that in case the wind park is granted access to the respective maximum price, there is a significant option value connected to the operational flexibility of accessing several markets: The wind...

The effects of meshed offshore grids on offshore wind investment – a real options analysis

DEFF Research Database (Denmark)

Schröder, Sascha Thorsten; Kitzing, Lena

2012-01-01

based on a stochastic model capturing uncertainties in prices and line failures. The stochastic analysis shows that in case the wind park is granted access to the respective maximum price, there is a significant option value connected to the operational flexibility of accessing several markets: The wind......Offshore wind farms in future meshed offshore grids could be subject to different regulatory regimes. Feed-in tariffs would absorb market risk from wind farm operators, whereas price premium mechanisms leave operators exposed to market price signals. In this case, it plays a decisive role which...... price applies to a node in an offshore grid. The offshore node will either be integrated into any of the neighbouring markets, with access to the respective maximum price, or be subject to separate nodal pricing. We investigate the different regulatory regimes for connections to one to four countries...

Wave Run-Up on Offshore Windturbine Foundations

DEFF Research Database (Denmark)

Frigaard, Peter; De Vos, Leen

2005-01-01

In the last decade, several offshore wind-farms are built and offshore wind energy promises to be a suitable alternative to provide green energy. However, there still are some engineering challenges in placing the wind turbine foundations offshore. For example, unexpected damage to boat landing...

China: an emerging offshore wind development hotspot. With a new assessment of China's offshore wind potential

Energy Technology Data Exchange (ETDEWEB)

Reinvang, Rasmus; Enslow, Rachel; Beaumont, Hubert

2010-08-15

This study provides new and more detailed estimates of the offshore wind energy resources in China, with particular focus on Southern China. The study points out that the offshore wind industry is ramping up in China with at least 11.9GW in the development pipeline per April 2010. The study estimates the offshore wind potential of China (excluding Taiwan) to 11,580TWh/year. The study proves estimates and wind energy resource maps per province. Fujian, Zhejiang and Hainan stand out with the highest offshore wind speeds in China while Guangdong also shows significant potential, with annual wind speed averages of 6.5-10.2m/s and an energy density range of 12-36GWh/km2. Even though current offshore wind development is mainly taking place in Fujian and Jiangsu, this study shows that the potential is likely even greater in other provinces. The study was developed by the Chinese Wind Energy Association (CWEA) and Sun Yat-sen University, and commissioned by WWF as part of a project funded by the Norwegian Agency of development Coopeartion (Norad). Methodology and constraints: The wind resource analysis improves upon previous studies in estimating the wind energy generation potential for offshore wind power in China, with available meteorological data adjusted for influence of typhoons. The study models how much energy offshore wind can produce along China's coast up to 100km from the shore by calculating the energy output of theoretical wind farms by applying the power curve of a 3MW turbine at a 100m hub height. In addition the study further expands by giving special consideration to the deep-sea offshore potential at +50m water depths. The study focuses particularly on the coastline from Shandong down to Hainan. The final results provide good indication of the offshore wind resource in China when comparing one area to the other. The report can therefore be used as a preliminary tool to identifying most interesting provinces and locations for offshore wind

Sr, Nd isotope geochemistry of volcanic rock series and its geological significance in the middle Okinawa Trough

Institute of Scientific and Technical Information of China (English)

无

2000-01-01

There exists extensive basic-acidic volcanic rock series in the middle section of the Okinawa Trough. Different types of these volcanic rocks have their own average strontium ratios of 0.704 749, 0.705 062, 0.708 771, 0.704 840 and 0.720 301 with average 143Nd/144Nd ratios of 0.512 820, 0.512 673, 0.512 413, 0.512 729 and 0.512 034. These ratios of Sr and Nd isotopes all fall on a theoretic hyperbolic curve of mixing between two end-members of MORB and rhyolitic magma. So we infer that these different kinds of volcanic rocks in the middle Okinawa Trough are the erupted product in different stages of formation and evolution of the trough crust. MORB magma, which had suffered assimilation, mixed with the early-formed crust-derived rhyolitic partial melt mass at different ratios; then, these mixed magma erupted and formed volcanic rock types of the trough. This study indicates that the Okinawa Trough is coming into a stage of submarine spreading from the stage of continental rift.

Sr, Nd isotope geochemistry of volcanic rock series and its geological significance in the middle Okinawa Trough

Institute of Scientific and Technical Information of China (English)

孟宪伟; 陈志华; 杜德文; 吴金龙

2000-01-01

There exists extensive basic-acidic volcanic rock series in the middle section of the Okinawa Trough. Different types of these volcanic rocks have their own average strontium ratios of 0.704749, 0.705062, 0.708771, 0.704840 and 0.720301 with average 143Nd/144Nd ratios of 0.512 820, 0.512 673, 0.512 413, 0.512 729 and 0.512 034. These ratios of Sr and Nd isotopes all fall on a theoretic hyperbolic curve of mixing between two end-members of MORE and rhyolitic magma. So we infer that these different kinds of volcanic rocks in the middle Okinawa Trough are the erupted product in different stages of formation and evolution of the trough crust. MORE magma, which had suffered assimilation, mixed with the early-formed crust-derived rhyolitic partial melt mass at different ratios; then, these mixed magma erupted and formed volcanic rock types of the trough. This study indicates that the Okinawa Trough is coming into a stage of submarine spreading from the stage of continental rift.

2016 Offshore Wind Technologies Market Report

Energy Technology Data Exchange (ETDEWEB)

Musial, Walter; Beiter, Philipp; Schwabe, Paul; Tian, Tian; Stehly, Tyler; Spitsen, Paul; Robertson, Amy; Gevorgian, Vahan

2017-08-08

The 2016 Offshore Wind Technologies Market Report was developed by the National Renewable Energy Laboratory (NREL) for the U.S. Department of Energy (DOE) and is intended to provide offshore wind policymakers, regulators, developers, researchers, engineers, financiers, and supply chain participants, with quantitative information about the offshore wind market, technology, and cost trends in the United States and worldwide. In particular, this report is intended to provide detailed information on the domestic offshore wind industry to provide context to help navigate technical and market barriers and opportunities. The scope of the report covers the status of the 111 operating offshore wind projects in the global fleet through December 31, 2016, and provides the status and analysis on a broader pipeline of 593 projects at some stage of development. In addition, this report provides a wider assessment of domestic developments and events through the second quarter of 2017 to provide a more up-to-date discussion of this dynamically evolving industry.

Benthic foraminiferal distribution in surface sediments along continental slope of the southern Okinawa Trough:dependance on water masses and food supply

Institute of Scientific and Technical Information of China (English)

向荣; 李铁刚; 杨作升; 阎军; 曹奇原

2003-01-01

Benthic foraminiferal analysis of 29 samples in surface sediments from the southern Oki-nawa Trough is carried out. The results indicate that benthic foraminiferal abundance decreases rapidlywith increasing water depth. Percentage frequencies of agglutinated foraminifera further confirm themodem shallow carbonate lysocline in the southern Okinawa Trough. From continental shelf edge to thebottom of Okinawa Trough, benthic foraminiferal fauna in the surface sediments can be divided into 5assemblages: (1) Continental shelf break assemblage, dominated by Cibicides pseudoungerianus, corre-sponds to subsurface water mass of the Kuroshio Current; (2) upper continental slope assemblage, domi-nated by Cassidulina carinata, Globocassidulina subglobosa, corresponds to intermediate water mass of the Kuroshio Current; (3) intermediate continental slope assemblage, dominated by Uvigerina hispi-da, corresponds to the Okinawa Trough deep water mass above the carbonate lysocline; (4) lower con-tinental slope- trough bottom assemblage, dominated by Pullenia bulloides, Epistominella exigua andCibicidoides hyalinus, corresponds to deep water mass of the Okinawa Trough; and (5) trough bottomagglutinated assemblage, dominated by Rhabdammina spp., Bathysiphon flavidus, corresponds tostrongly dissolved environment of the trough bottom. The benthic foraminiferal fauna in the southemOkinawa Trough are controlled jointly by water masses and food supply. Water temperature, oxygenconcentration and carbonate dissolution of the water masses are important controlling factors especiallyfor the continental shelf break and trough bottom assemblages. The food supply also plays an importantrole in these benthic foraminiferal assemblages along the westem slope of the Okinawa Trough. Both theabundance and the 5 assemblages of benthic foraminifera correspond well to the organic matter supplyalong the continental slope and a lateral transport of TSM (total suspended matter) and POC (particulateorganic

Geological records of marine environmental changes in the southern Okinawa Trough

Institute of Scientific and Technical Information of China (English)

无

2003-01-01

Indexes of sediment grain size, sedimentation rates, geochemical composition, heavy minerals, benthic foraminiferal fauna, indicator species of the Kuroshio Current, paleo-SST and carbonate dissolution of core E017 conformably suggest a great marine environmental change occurring at about 10.1-9.2 cal. kaBP in the southern Okinawa Trough, which may correspond to the strengthening of the Kuroshio Warm Current and re-entering the Okinawa Trough through the sea area off northeast Taiwan. The invasion of Kuroshio current has experienced a process of gradual strengthening and then weakening, and its intensity became more fluctuation during the last 5000 years. Compared to the transition of sediment grain size, geochemical composition and heavy minerals, the foraminiferal faunas show a 900-year lag, which may indicate that the invasion of Kuroshio Current and the consequent sea surface and deep-water environmental changes is a gradual process, and fauna has an obvious lag compared to environment altering. The carbonate dissolution of the Okinawa Trough has had an apparent strengthening since 9.2 cal. kaBP, and reached a maximum in the late 3000 years, which may be caused by the deep-water environmental changes due to the invasion of Kuroshio Current.

Slip rate on the San Diego trough fault zone, inner California Borderland, and the 1986 Oceanside earthquake swarm revisited

Science.gov (United States)

Ryan, Holly F.; Conrad, James E.; Paull, C.K.; McGann, Mary

2012-01-01

The San Diego trough fault zone (SDTFZ) is part of a 90-km-wide zone of faults within the inner California Borderland that accommodates motion between the Pacific and North American plates. Along with most faults offshore southern California, the slip rate and paleoseismic history of the SDTFZ are unknown. We present new seismic reflection data that show that the fault zone steps across a 5-km-wide stepover to continue for an additional 60 km north of its previously mapped extent. The 1986 Oceanside earthquake swarm is located within the 20-km-long restraining stepover. Farther north, at the latitude of Santa Catalina Island, the SDTFZ bends 20° to the west and may be linked via a complex zone of folds with the San Pedro basin fault zone (SPBFZ). In a cooperative program between the U.S. Geological Survey (USGS) and the Monterey Bay Aquarium Research Institute (MBARI), we measure and date the coseismic offset of a submarine channel that intersects the fault zone near the SDTFZ–SPBFZ junction. We estimate a horizontal slip rate of about 1:5 0:3 mm=yr over the past 12,270 yr.

Offshore Fish Community: Ecological Interactions

Science.gov (United States)

The offshore (>80 m) fish community of Lake Superior is made up of predominately native species. The most prominent species are deepwater sculpin, kiyi, cisco, siscowet lake trout, burbot, and the exotic sea lamprey. Bloater and shortjaw cisco are also found in the offshore zone...

Offshore wind power in Finland

Energy Technology Data Exchange (ETDEWEB)

Holttinen, H. [VTT Energy, Espoo (Finland)

1998-12-31

The objectives of the project were to estimate the technical offshore wind power potential of the Gulf of Bothnia, with cost assessments, to study icing conditions and ice loads, and to design a foundation suitable for the environmental conditions. The technical offshore potential from Vaasa to Tornio is huge, more than 40 TWh/a, although the cost of offshore wind power is still higher than on land. Wind turbines have not previously been designed for the icing conditions found in Gulf of Bothnia and the recommendations for load cases and siting of megawatt-class turbines are an important result of the project. (orig.)

Offshore Wind Energy Cost Modeling Installation and Decommissioning

CERN Document Server

Kaiser, Mark J

2012-01-01

Offshore wind energy is one of the most promising and fastest growing alternative energy sources in the world. Offshore Wind Energy Cost Modeling provides a methodological framework to assess installation and decommissioning costs, and using examples from the European experience, provides a broad review of existing processes and systems used in the offshore wind industry. Offshore Wind Energy Cost Modeling provides a step-by-step guide to modeling costs over four sections. These sections cover: ·Background and introductory material, ·Installation processes and vessel requirements, ·Installation cost estimation, and ·Decommissioning methods and cost estimation.  This self-contained and detailed treatment of the key principles in offshore wind development is supported throughout by visual aids and data tables. Offshore Wind Energy Cost Modeling is a key resource for anyone interested in the offshore wind industry, particularly those interested in the technical and economic aspects of installation and decom...

Offshore petroleum engineering task force report

International Nuclear Information System (INIS)

Ruelokke, M.

1999-05-01

The Offshore Petroleum Engineering Task Force was established in July 1998 in response to concerns about Newfoundland and Labrador's share of offshore petroleum engineering activity, with the aim of determining the current capability of the local sector, the demand for such companies and individuals until the year 2010, their capability to grow over that time-frame, and requirements in order to achieve that growth. The report summarizes the analysis undertaken by the Task Force as well as the conclusions it reached and associated recommendations. Section two provides an overview of the offshore engineering activity, including its origins, structure, and key success factors, and its also provides a profile of the industry, internationally, in Canada and in Newfoundland. Section three presents an analysis of the future demand for offshore engineering in Newfoundland until 2010, based on three development scenarios. Section four based on a Consulting Engineers of Newfoundland and Labrador (CENL) survey, establishes the present offshore engineering capacity and capabilities within the province. Section five examines current education and training programs and their ability to respond to future demands. Section six summarizes the conclusions of the analysis and presents recommendations designed to facilitate and promote the development of the local offshore engineering industry. 6 figs

Grid Integration of Offshore Wind | Wind | NREL

Science.gov (United States)

Grid Integration of Offshore Wind Grid Integration of Offshore Wind Much can be learned from the existing land-based integration research for handling the variability and uncertainty of the wind resource Arklow Bank offshore wind park consists of seven GE Wind 3.6-MW wind turbines. Integration and

Conference on offshore wind power in France and Germany

International Nuclear Information System (INIS)

Meyer, Ronny; Furois, Timothee; Nolte, Nico; Lanoe, Frederic; Lehmann-Matthaei, Bjoern; Ifflaender, Andree; Courcambeck, Alexandre; Giese, Norbert; Kavafyan, Philippe; Bjaert, Niels; Wagner, Andreas; Guillet, Jerome

2014-01-01

The French-German office for Renewable energies (OFAEnR) organised a conference on offshore wind power in France and Germany. In the framework of this French-German exchange of experience, about 120 participants exchanged views on the planning and authorisation procedures implemented in both countries and on the installation, connection to the grid and maintenance of offshore wind turbines. environmental impacts and usage conflicts linked with offshore wind farms exploitation were addressed as well. This document brings together the available presentations (slides) made during this event: 1 - Update: Offshore Wind In Germany (Ronny Meyer); 2 - Offshore wind development in France (Timothee Furois); 3 - The Licensing Procedure for Offshore Wind Farms in the German EEZ (Nico Nolte); 4 - Spatial Planning and Permitting in France: What leverage for more efficiency? (Frederic Lanoe); 5 - Results of 10 years environmental research on FINO-platforms (Bjoern Lehmann-Matthaei); 6 - Offshore Grid Connection - Status Quo and Overview (Andree Ifflaender); 7 - Grid connection of Offshore Wind in France: Situation, perspectives and recommendations (Alexandre Courcambeck); 8 - Controlling risks and warranting safety: Best practices for the installation, exploitation and maintenance of offshore wind turbines (Norbert Giese); 9 - Offshore wind Bremerhaven experience: An essential asset for the development of a complete Wind Offshore industry in France (Philippe Kavafyan); 10 - Standardizing and Cost Reduction -Lessons Learned from London Array (Niels Bjaert); 11 - Offshore Wind energy in Germany: System Benefits and Cost Reduction Potentials. Presentation of study results from prognos/fichtner and Fraunhofer-IWeS (Andreas Wagner); 12 - Offshore Wind energy financing - opportunities and risks (Jerome Guillet)

Denmark - supplier of competitive offshore wind solutions. Megavind's strategy for offshore wind research, development and demonstration

Energy Technology Data Exchange (ETDEWEB)

2010-12-15

In May 2006, the Danish Government presented a report on promoting environmentally effective technology and established a number of innovative partnerships. The partnerships intend to strengthen public-private cooperation between the state, industry, universities and venture capital to accelerate innovation for a number of green technologies. The partnership for wind energy is called Megavind. Megavind's strategy for offshore wind describes the offshore challenges and suggests research, development and demonstration (RD and D) priorities to enable offshore wind power become to competitive with other energy technologies. The strategy lists key recommendations as well as key thematic priorities and for each of these a number of RD and D priorities. Under each thematic priority references are made to the European Strategic Energy Technology plan (SET-plan), which prioritises offshore wind RD and D in Europe. (LN)

Humidification dehumidification desalination system using parabolic trough solar air collector

International Nuclear Information System (INIS)

Al-Sulaiman, Fahad A.; Zubair, M. Ifras; Atif, Maimoon; Gandhidasan, Palanichamy; Al-Dini, Salem A.; Antar, Mohamed A.

2015-01-01

This paper deals with a detailed thermodynamic analysis to assess the performance of an HDH system with an integrated parabolic trough solar collector (PTSC). The HDH system considered is an open air, open water, air heated system that uses a PTSC as an air heater. Two different configurations were considered of the HDH system. In the first configuration, the solar air heater was placed before the humidifier whereas in the second configuration the solar air heater was placed between the humidifier and the dehumidifier. The current study revealed that PTSCs are well suited for air heated HDH systems for high radiation location, such as Dhahran, Saudi Arabia. The comparison between the two HDH configurations demonstrates that the gained output ratio (GOR) of the first configuration is, on average, about 1.5 whereas for the second configuration the GOR increases up to an average value of 4.7. The study demonstrates that the HDH configuration with the air heater placed between the humidifier and the dehumidifier has a better performance and a higher productivity. - Highlights: • Thermodynamic analysis of an HDH system driven by a parabolic trough solar collector was conducted. • The first configuration reveals a GOR of 1.5 while the second configuration reveals a GOR of 4.7. • Effective heating of the HDH system was obtained through parabolic trough solar collector

The offshore benthic fish community

Science.gov (United States)

Lantry, Brian F.; Lantry, Jana R.; Weidel, Brian C.; Walsh, Maureen; Hoyle, James A.; Schaner, Teodore; Neave, Fraser B.; Keir, Michael

2014-01-01

Lake Ontario’s offshore benthic fish community includes primarily slimy sculpin, lake whitefish, rainbow smelt, lake trout, burbot, and sea lamprey. Of these, lake trout have been the focus of an international restoration effort for more than three decades (Elrod et al. 1995; Lantry and Lantry 2008). The deepwater sculpin and three species of deepwater ciscoes (Coregonus spp.) that were historically important in the offshore benthic zone became rare or were extirpated by the 1960s (Christie 1973; Owens et al. 2003; Lantry et al. 2007b; Roth et al. 2013). Ecosystem changes continue to influence the offshore benthic fish community, including the effects of dreissenid mussels, the near disappearance of burrowing amphipods (Diporeia spp.) (Dermott et al. 2005; Watkins et al. 2007), and the increased abundance and expanded geographic distribution of round goby (see Nearshore Fish Community chapter) (Lantry et al. 2007b). The fish-community objectives for the offshore benthic fish community, as described by Stewart et al. (1999), are:

IFREMER-ADEME colloquium 'Offshore renewable energies: offshore wind energy - sea currents and waves. Collection of abstracts

International Nuclear Information System (INIS)

2004-10-01

This document contains programme and abstracts of contributions presented during a colloquium. These contributions first addresses the context, and regulatory and economic aspects of offshore wind and sea energy: specificities related to the Public Maritime Domain for the implantation of offshore wind turbines, economy of sea energies within a perspective of de-carbonation of the world energy sector, case of offshore wind turbines and assessment of economic impacts of the implantation of sea renewable energy production units, financing stakes for offshore wind energy projects. A second set of contribution addresses the state-of -the-art and feedbacks for offshore wind energy installations. The third set addresses the assessment of resource potential, measurements, models and production prediction for offshore wind energy: case of French coasts, use of radar for remote sensing, wind climatology modelling, data acquisition for wind farm and data processing. The fourth set of contributions addresses the state-of-the-art, feedback, and R and D for sea current energy, while the fifth one addressed the same aspects for sea wave energy. Technology, installations, maintenance and storage in the field of wind energy are then addressed, and the last set deals with environmental and social-economical impacts of sea renewable energies

The onshore influence of offshore fresh groundwater

Science.gov (United States)

Knight, Andrew C.; Werner, Adrian D.; Morgan, Leanne K.

2018-06-01

Freshwater contained within the submarine extensions of coastal aquifers is increasingly proposed as a freshwater source for coastal communities. However, the extent to which offshore freshwater supports onshore pumping is currently unknown on a global scale. This study provides the first attempt to examine the likely prevalence of situations where offshore freshwater influences onshore salinities, considering various sites from around the world. The groundwater conditions in twenty-seven confined and semi-confined coastal aquifers with plausible connections to inferred or observed offshore freshwater are explored. The investigation uses available onshore salinities and groundwater levels, and offshore salinity knowledge, in combination with analytical modelling, to develop simplified conceptual models of the study sites. Seven different conceptual models are proposed based on the freshwater-saltwater extent and insights gained from analytical modelling. We consider both present-day and pre-development conditions in assessing potential modern contributions to offshore fresh groundwater. Conceptual models also include interpretations of whether offshore freshwater is a significant factor influencing onshore salinities and well pumping sustainability. The results indicate that onshore water levels have declined between pre-development and present-day conditions in fourteen of the fifteen regions for which pre-development data are available. Estimates of the associated steady-state freshwater extents show the potential for considerable offshore fresh groundwater losses accompanying these declines. Both present-day and pre-development heads are insufficient to account for the observed offshore freshwater in all cases where adequate data exist. This suggests that paleo-freshwater and/or aquifer heterogeneities contribute significantly to offshore freshwater extent. Present-day heads indicate that active seawater intrusion (SWI) will eventually impact onshore pumping

Developments in offshore technology. Entwicklungen in der Offshoretechnik

Energy Technology Data Exchange (ETDEWEB)

1981-01-01

This book contains the summarized lectures held on the 8th of October, 1981 within the first status Seminar 'Offshore technology' which was organized by the Federal Minstry for Research and Technology. Contents are divided into: 1. Offshore-natural gas liquefaction, conveying systems. Offshore-tanker charging with supercold liquiefied gases; development of LNG-offshore - convayance systems; 2.) Development of components and installations in offshore structures: mooving-measuring- and monitoring systems for the installation of the EPOS deck; underwater-piling with a hydraulic-pile hammer; cast steel nodes for offshore-structures (material, calculation, design); 3.) underwater tools: the underwater-working system SUPRA; test results and experience with the unmanned UW-instrument-carrier FUGE; development of a mobile diver assistance vehicle for inspection and maintenance duties; 4.) underwater-pipeline-technique: flexible offshore-pipeline/continuous production and assembly, pipeline assembly at sea according to the J-Method with flash-welding technique; construction and testing of UWAG I (underwater working device) for embedding cables and pipes in the ocean soil.

Understanding public responses to offshore wind power

International Nuclear Information System (INIS)

Haggett, Claire

2011-01-01

This paper is about understanding the role and importance of public responses to offshore wind power. It builds on a framework for understanding social acceptance and opposition to onshore turbines, and reviews the emerging research on offshore wind. While less is known about how people will respond to offshore than onshore wind, there is now an emerging body of research. From this literature, several common factors which influence responses have emerged and are discussed here: the (continued) role of visual impact; place attachment to the local area; lack of tangible benefits; relationships with developers and outsiders; and the role of the planning and decision-making systems. The paper argues that, as with onshore developments, the public should be included in decision-making about offshore wind farms, and that they have a key role which should not be underestimated. The paper concludes with some thoughts about the means to involve people and how effected communities might be effectively acknowledged, identified and engaged. - Research Highlights: →Comprehensive review of public responses to offshore wind literature. →Applies key lessons and analytic insights from onshore wind to offshore wind. →Emphasizes the role and importance of the public in the planning and implementation of offshore wind energy.

Global Production: The Case of Offshore Programming

DEFF Research Database (Denmark)

Nørbjerg, Jacob; Havn, Erling; Bansler, Jørgen P.

1997-01-01

of software is no exception.In this paper, we present a newly started research project on offshore program-ming, that is the practice of sending software development “offshore,” to India or other low wage areas. The project focuses on the organisation of offshore program-ming and, particularly, on the role...

Socio-economic Impacts—Offshore Activities/Energy

DEFF Research Database (Denmark)

Halsnæs, Kirsten; Drews, Martin; Clausen, Niels-Erik

2016-01-01

sector and renewable electricity generation—mainly from offshore wind—is increasing. Energy and offshore activities in the North Sea are critically vulnerable to climate change along the full supply chain. The major vulnerabilities for offshore installations like rigs, offshore wind energy and pipelines......, it is highly uncertain how much the future potential of other renewable energy sources such as wind, solar, terrestrial biomass, or emerging technologies like wave, tidal or marine biomass could be positively or negatively affected. Due to the different national energy supply mixes the vulnerability to climate......-related impacts will vary among North Sea countries. To ensure safe and reliable future operations comprehensive and systematic risk assessments are therefore needed which account for, for example, the high integration of power systems in the region....

Understanding the Compositional Variability of the Major Components of Hydrothermal Plumes in the Okinawa Trough

Directory of Open Access Journals (Sweden)

Zhigang Zeng

2018-01-01

Full Text Available Studies of the major components of hydrothermal plumes in seafloor hydrothermal fields are critical for an improved understanding of biogeochemical cycles and the large-scale distribution of elements in the submarine environment. The composition of major components in hydrothermal plume water column samples from 25 stations has been investigated in the middle and southern Okinawa Trough. The physical and chemical properties of hydrothermal plume water in the Okinawa Trough have been affected by input of the Kuroshio current, and its influence on hydrothermal plume water from the southern Okinawa Trough to the middle Okinawa Trough is reduced. The anomalous layers of seawater in the hydrothermal plume water columns have higher K+, Ca2+, Mn2+, B3+, Ca2+/SO42-, and Mn2+/Mg2+ ratios and higher optical anomalies than other layers. The Mg2+, SO42-, Mg2+/Ca2+, and SO42-/Mn2+ ratios of the anomalous layers are lower than other layers in the hydrothermal plume water columns and are consistent with concentrations in hydrothermal vent fluids in the Okinawa Trough. This suggests that the chemical variations of hydrothermal plumes in the Tangyin hydrothermal field, like other hydrothermal fields, result in the discharge of high K+, Ca2+, and B3+ and low Mg2+ and SO42- fluid. Furthermore, element ratios (e.g., Sr2+/Ca2+, Ca2+/Cl− in hydrothermal plume water columns were found to be similar to those in average seawater, indicating that Sr2+/Ca2+ and Ca2+/Cl− ratios of hydrothermal plumes might be useful proxies for chemical properties of seawater. The hydrothermal K+, Ca2+, Mn2+, and B3+ flux to seawater in the Okinawa Trough is about 2.62–873, 1.04–326, 1.30–76.4, and 0.293–34.7 × 106 kg per year, respectively. The heat flux is about 0.159–1,973 × 105 W, which means that roughly 0.0006% of ocean heat is supplied by seafloor hydrothermal plumes in the Okinawa Trough.

9 CFR 82.21 - Vehicles, cages, coops, containers, troughs, and other equipment used for infected poultry.

Science.gov (United States)

2010-01-01

..., troughs, and other equipment used for infected poultry. 82.21 Section 82.21 Animals and Animal Products... ANIMALS (INCLUDING POULTRY) AND ANIMAL PRODUCTS EXOTIC NEWCASTLE DIS- EASE (END) AND CHLAMYDIOSIS Chlamydiosis in Poultry § 82.21 Vehicles, cages, coops, containers, troughs, and other equipment used for...

Absorber Alignment Measurement Tool for Solar Parabolic Trough Collectors: Preprint

Energy Technology Data Exchange (ETDEWEB)

Stynes, J. K.; Ihas, B.

2012-04-01

As we pursue efforts to lower the capital and installation costs of parabolic trough solar collectors, it is essential to maintain high optical performance. While there are many optical tools available to measure the reflector slope errors of parabolic trough solar collectors, there are few tools to measure the absorber alignment. A new method is presented here to measure the absorber alignment in two dimensions to within 0.5 cm. The absorber alignment is measured using a digital camera and four photogrammetric targets. Physical contact with the receiver absorber or glass is not necessary. The alignment of the absorber is measured along its full length so that sagging of the absorber can be quantified with this technique. The resulting absorber alignment measurement provides critical information required to accurately determine the intercept factor of a collector.

Operational management of offshore energy assets

Science.gov (United States)

Kolios, A. J.; Martinez Luengo, M.

2016-02-01

Energy assets and especially those deployed offshore are subject to a variety of harsh operational and environmental conditions which lead to deterioration of their performance and structural capacity over time. The aim of reduction of CAPEX in new installations shifts focus to operational management to monitor and assess performance of critical assets ensuring their fitness for service throughout their service life and also to provide appropriate and effective information towards requalification or other end of life scenarios, optimizing the OPEX. Over the last decades, the offshore oil & gas industry has developed and applied various approaches in operational management of assets through Structural Health and Condition Monitoring (SHM/CM) systems which can be, at a certain level, transferable to offshore renewable installations. This paper aims to highlight the key differences between offshore oil & gas and renewable energy assets from a structural integrity and reliability perspective, provide a comprehensive overview of different approaches that are available and applicable, and distinguish the benefits of such systems in the efficient operation of offshore energy assets.

Fine Slicing of the Value Chain and Offshoring of Essential Activities

DEFF Research Database (Denmark)

Linares-Navarro, Esmeralda; Pedersen, Torben; Pla-Barber, José

2014-01-01

The offshoring of more advanced activities is increasing and a debate about the limits of offshoring has emerged. Companies are fine-slicing their value chains, and moving beyond the offshoring of peripheral and non-core activities to the offshoring of advanced and essential activities that are c......The offshoring of more advanced activities is increasing and a debate about the limits of offshoring has emerged. Companies are fine-slicing their value chains, and moving beyond the offshoring of peripheral and non-core activities to the offshoring of advanced and essential activities...... that companies are redefining their core activities and in this process, some essential activities previously viewed as core activities are being detached from the core, and they become more offshorable. The study uses a sample of 565 offshoring operations conducted by 263 multinational companies from 15...... European countries. A logistic regression was used to analyze the relationship between the activities offshored (non-core versus essential activities) and the offshoring mode implemented (captive offshoring versus offshore outsourcing). We find that essential activities are typically offshored using...

Comparative analyses of the bacterial community of hydrothermal deposits and seafloor sediments across Okinawa Trough

Science.gov (United States)

Wang, Long; Yu, Min; Liu, Yan; Liu, Jiwen; Wu, Yonghua; Li, Li; Liu, Jihua; Wang, Min; Zhang, Xiao-Hua

2018-04-01

As an ideal place to study back-arc basins and hydrothermal eco-system, Okinawa Trough has attracted the interests of scientists for decades. However, there are still no in-depth studies targeting the bacterial community of the seafloor sediments and hydrothermal deposits in Okinawa Trough. In the present study, we reported the bacterial community of the surface deposits of a newly found hydrothermal field in the southern Okinawa Trough, and the horizontal and vertical variation of bacterial communities in the sediments of the northern Okinawa Trough. The hydrothermal deposits had a relatively high 16S rRNA gene abundance but low bacterial richness and diversity. Epsilonproteobacteria and Bacteroidetes were predominant in hydrothermal deposits whereas Deltaproteobacteria, Gammaproteobacteria and Chloroflexi were abundant across all samples. The bacterial distribution in the seafloor of Okinawa Trough was significantly correlated to the content of total nitrogen, and had consistent relationship with total carbon. Gradual changes of sulfur-oxidizing bacteria were found with the distance away from hydrothermal fields, while the hydrothermal activity did not influence the distribution of the major clades of sulfate-reducing bacteria. Higher abundance of the sulfur cycle related genes (aprA and dsrB), and lower abundance of the bacterial ammonia-oxidizing related gene (amoA) were quantified in hydrothermal deposits. In addition, the present study also compared the inter-field variation of Epsilonproteobacteria among multi-types of hydrothermal vents, revealing that the proportion and diversity of this clade were quite various.

Pricing offshore wind power

International Nuclear Information System (INIS)

Levitt, Andrew C.; Kempton, Willett; Smith, Aaron P.; Musial, Walt; Firestone, Jeremy

2011-01-01

Offshore wind offers a very large clean power resource, but electricity from the first US offshore wind contracts is costlier than current regional wholesale electricity prices. To better understand the factors that drive these costs, we develop a pro-forma cash flow model to calculate two results: the levelized cost of energy, and the breakeven price required for financial viability. We then determine input values based on our analysis of capital markets and of 35 operating and planned projects in Europe, China, and the United States. The model is run for a range of inputs appropriate to US policies, electricity markets, and capital markets to assess how changes in policy incentives, project inputs, and financial structure affect the breakeven price of offshore wind power. The model and documentation are made publicly available. - Highlights: → We calculate the Breakeven Price (BP) required to deploy offshore wind plants. → We determine values for cost drivers and review incentives structures in the US. → We develop 3 scenarios using today's technology but varying in industry experience. → BP differs widely by Cost Scenario; relative policy effectiveness varies by stage. → The low-range BP is below regional market values in the Northeast United States.

A modelling study of the post-sunset formation of plasma temperature troughs in the equatorial topside ionosphere

International Nuclear Information System (INIS)

Bailey, G.J.; Moffett, R.J.; Simmons, P.A.; Footitt, R.J.

1986-01-01

Results of model calculations are used to study the post-sunset development of plasma temperature troughs along tubes of plasma at equatorial latitudes. The calculations show that for about 90 minutes after sunset the ion field-aligned velocities are directed poleward in both hemispheres even though the meridional neutral air wind blows from the summer hemisphere to the winter hemisphere. After about 90 minutes the ion field-aligned velocities become directed from the summer hemisphere to the winter hemisphere in both hemispheres. As time advances plasma temperature troughs are formed along the tubes of plasma. Initially the plasma temperature troughs increase in depth, but because in the calculations the tubes of plasma are taken to be moving towards the Earth, the plasma temperature troughs then decrease in depth. At sunspot maximum the plasma temperature troughs are deep and narrow in dip latitude; at sunspot minimum they are shallow and wide. It is shown that the ion field-aligned velocities and the depth of the plasma temperature troughs are extremely sensitive to the neutral atomic hydrogen concentration, especially when the topside ionosphere is dominated by O + . Indications are that the MSIS-83 sunspot maximum concentrations of neutral atomic hydrogen in the topside ionosphere at equatorial latitudes are too low by a factor of about 2. The neutral atomic hydrogen concentration determines whether the transequatorial O + flow is a subsonic ''breeze'' or a supersonic ''wind''

Offshore Supply Industry Dynamics

DEFF Research Database (Denmark)

Roslyng Olesen, Thomas

This report is part of the research project “The competitive challenges and strategic development possibilities for The Blue Denmark”, which was launched in 2014. The project is funded by the Danish Maritime Fund and carried out by researchers at CBS Maritime which is a Business in Society Platform...... with companies in the maritime sector. This report “Offshore Supply Industry Dynamics – Business strategies in the offshore supply industry” is the second report in mapping project D. It examines the markets and business strategies of various suppliers and furthermore presents an analysis of the challenges...... at Copenhagen Business School with a focus on value creation in the maritime industries. The project embraces various maritime segments from shipping and offshore to ports and suppliers. The research questions for the individual projects have been formulated by researchers at CBS Maritime in cooperation...

Offshore rectenna feasbility

Science.gov (United States)

Freeman, J. W.; Hervey, D.; Glaser, P.

1980-01-01

A preliminary study of the feasibility and cost of an offshore rectenna to serve the upper metropolitan east coast was performed. A candidate site at which to build a 5 GW rectenna was selected on the basis of proximity to load centers, avoidance of shipping lanes, sea floor terrain, and relocated conditions. Several types of support structures were selected for study based initially on the reference system rectenna concept of a wire mesh ground screen and dipoles each with its own rectifier and filter circuits. Possible secondary uses of an offshore rectenna were examined and are evaluated.

Gela offshore field

Energy Technology Data Exchange (ETDEWEB)

Pagliughi, G

1965-06-01

The field of Gela, off the southern shore of Sicily, is the only producing offshore field in the Mediterranean. It produces from Triassic dolimite limestones of 434-m thickness, water level at -3517 m. It is a water-drive reservoir producing 10/sup 0/F API oil and has 79 wells, some of them on shore. Most offshore wells are directional wells from shore; there are also 2 fixed platforms and a special mobile platform. The wells are on pump (stroke, 72 in.; capacity 200 tons per day). The crude goes directly to a combination refinery-petrochemical complex at Gela.

Offshore Energy Knowledge Exchange Workshop Report

Energy Technology Data Exchange (ETDEWEB)

none,

2012-04-12

A report detailing the presentations and topics discussed at the Offshore Energy Knowledge Exchange Workshop, an event designed to bring together offshore energy industry representatives to share information, best practices, and lessons learned.

Attitude and acceptance of offshore wind farms

DEFF Research Database (Denmark)

Ladenburg, Jacob; Möller, B.

2011-01-01

farms attributes on attitude towards offshore wind farms. The results point towards that the travel time and the attributes of the nearest offshore wind farm influence the attitude significantly. Travel time has mixed effects on the attitude, whilst offshore wind farms with many turbines generate more...... a novel contribution to this field. First of all, we give a thorough review of the studies that have analysed the relation between experience with wind turbines and attitude. In addition, we supplement the review by analysing the effect of travel distance to the nearest offshore wind farm and the wind...

The Capabilities of the Offshore Middlemen

DEFF Research Database (Denmark)

Mahnke, Volker; Wareham, Jonathan

preliminary theoretical justification for the emergence of offshore intermediaries; describe how and why they develop intermediation capabilities; and offer initial evidence substantiating their function and processes in intermediating transnational offshoring relationships in software development...

Environmental risk in the offshore industry

International Nuclear Information System (INIS)

Woods, I.T.; Shirley, D.; Bottelberghs, P.H.

1991-01-01

The subject of oil pollution of the sea by the offshore industry is topical as a result of recent incidents both in the U.K. and overseas. While these incidents have primarily involved crude carriers, it has led to pressure to quantify the risk to the environment from the offshore industry in general. In this paper a method for the assessment of the frequency and size of oil spills from offshore installations is presented. It relies on previously reported spills to determine spill size/frequency information for a range of offshore activities, such as transport by pipeline, drilling and processing. Modification factors are used so local conditions, such as the number of wells drilled, throughput and well depth, can be considered in the assessment of the oil spill risk from a particular installation

Strawberry Production in Soilless Substrate Troughs – Plant Growth

Science.gov (United States)

Soilless substrates made of peat moss, coconut coir, perlite, rockwool or bark are pathogen free and they have been used in strawberry production in Europe in troughs or containers. Open field strawberry production in soilless substrate is new to California growers. The objective of this study was t...

Noble gas and carbon isotopes in Mariana Trough basalt glasses

International Nuclear Information System (INIS)

Bernard, M.; Jambon, A.; Gamo, T.; Nishio, Y.; Sano, Y.

1998-01-01

Noble gas elemental and isotopic compositions have been measured as well as the abundance of C and its isotopic ratios in 11 glasses from submarine pillow basalts collected from the Mariana Trough. The 3 He/ 4 He ratios of 8.22 and 8.51 R atm of samples dredged from the central Mariana Trough (similar18N) agree well with that of the Mid-Ocean Ridge Basalt (MORB) glasses (8.4±0.3 R atm ), whereas a mean ratio of 8.06±0.35 R atm in samples from the northern Mariana Trough (similar20N) is slightly lower than those of MORB. One sample shows apparent excess of 20 Ne and 21 Ne relative to atmospheric Ne, suggesting incorporation of solar-type Ne in the magma source. There is a positive correlation between 3 He/ 4 He and 40 Ar/ 36 Ar ratios, which may be explained by mixing between MORB-type and atmospheric noble gases. Excess 129 Xe is observed in the sample which also shows 20 Ne and 21 Ne excesses. Observed δ 13 C values of similar20N samples vary from -3.76 per thousand to -2.80 per thousand, and appear higher than those of MORB, and the corresponding CO 2 / 3 He ratios are higher than those of MARA samples at similar18N, suggesting C contribution from the subducted slab. (Copyright (c) 1998 Elsevier Science B.V., Amsterdam. All rights reserved.)

10 CFR 150.7 - Persons in offshore waters not exempt.

Science.gov (United States)

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Persons in offshore waters not exempt. 150.7 Section 150.7... AGREEMENT STATES AND IN OFFSHORE WATERS UNDER SECTION 274 Continued Commission Regulatory Authority in Offshore Waters § 150.7 Persons in offshore waters not exempt. Persons in offshore waters are not exempt...

Detailed Physical Trough Model for NREL's Solar Advisor Model: Preprint

Energy Technology Data Exchange (ETDEWEB)

Wagner, M. J.; Blair, N.; Dobos, A.

2010-10-01

Solar Advisor Model (SAM) is a free software package made available by the National Renewable Energy Laboratory (NREL), Sandia National Laboratory, and the US Department of Energy. SAM contains hourly system performance and economic models for concentrating solar power (CSP) systems, photovoltaic, solar hot-water, and generic fuel-use technologies. Versions of SAM prior to 2010 included only the parabolic trough model based on Excelergy. This model uses top-level empirical performance curves to characterize plant behavior, and thus is limited in predictive capability for new technologies or component configurations. To address this and other functionality challenges, a new trough model; derived from physical first principles was commissioned to supplement the Excelergy-based empirical model. This new 'physical model' approaches the task of characterizing the performance of the whole parabolic trough plant by replacing empirical curve-fit relationships with more detailed calculations where practical. The resulting model matches the annual performance of the SAM empirical model (which has been previously verified with plant data) while maintaining run-times compatible with parametric analysis, adding additional flexibility in modeled system configurations, and providing more detailed performance calculations in the solar field, power block, piping, and storage subsystems.

Water-hydraulic power transmission for offshore wind farms

NARCIS (Netherlands)

Diepeveen, N.F.B.; Jarquin Laguna, A.; Kempenaar, A.S.

2012-01-01

The current state of the art of offshore wind turbine power transmission technology is expensive, heavy and maintenance intensive. The Delft Offshore Turbine project considers a radically new concept for power transmission in an offshore wind farm: using seawater as power transmission medium. For

Balancing vancomycin efficacy and nephrotoxicity: should we be aiming for trough or AUC/MIC?

Science.gov (United States)

Patel, Karisma; Crumby, Ashley S; Maples, Holly D

2015-04-01

Sixty years later, the question that still remains is how to appropriately utilize vancomycin in the pediatric population. The Infectious Diseases Society of America published guidelines in 2011 that provide guidance for dosing and monitoring of vancomycin in adults and pediatrics. However, goal vancomycin trough concentrations of 15-20 μg/mL for invasive infections caused by methicillin-resistant Staphylococcus aureus were based primarily on adult pharmacokinetic and pharmacodynamic data that achieved an area under the curve to minimum inhibitory concentration ratio (AUC/MIC) of ≥400. Recent pediatric literature shows that vancomycin trough concentrations needed to achieve the target AUC/MIC are different than the adult goal troughs cited in the guidelines. This paper addresses several thoughts, including the role of vancomycin AUC/MIC in dosing strategies and safety monitoring, consistency in laboratory reporting, and future directions for calculating AUC/MIC in pediatrics.

Offshore Wind Energy Systems Engineering Curriculum Development

Energy Technology Data Exchange (ETDEWEB)

McGowan, Jon G. [Univ. of Massachusetts, Amherst, MA (United States); Manwell, James F. [Univ. of Massachusetts, Amherst, MA (United States); Lackner, Matthew A. [Univ. of Massachusetts, Amherst, MA (United States)

2012-12-31

Utility-scale electricity produced from offshore wind farms has the potential to contribute significantly to the energy production of the United States. In order for the U.S. to rapidly develop these abundant resources, knowledgeable scientists and engineers with sound understanding of offshore wind energy systems are critical. This report summarizes the development of an upper-level engineering course in "Offshore Wind Energy Systems Engineering." This course is designed to provide students with a comprehensive knowledge of both the technical challenges of offshore wind energy and the practical regulatory, permitting, and planning aspects of developing offshore wind farms in the U.S. This course was offered on a pilot basis in 2011 at the University of Massachusetts and the National Renewable Energy Laboratory (NREL), TU Delft, and GL Garrad Hassan have reviewed its content. As summarized in this report, the course consists of 17 separate topic areas emphasizing appropriate engineering fundamentals as well as development, planning, and regulatory issues. In addition to the course summary, the report gives the details of a public Internet site where references and related course material can be obtained. This course will fill a pressing need for the education and training of the U.S. workforce in this critically important area. Fundamentally, this course will be unique due to two attributes: an emphasis on the engineering and technical aspects of offshore wind energy systems, and a focus on offshore wind energy issues specific to the United States.

Offshoring in textile industry

OpenAIRE

MONTÓN GARCÍA, JORGE

2015-01-01

[ EN] This project is about offshoring in the textile industry, focusing in the rights violated in this process, this concept can be defined as the moving of various operations of a company to another country for reasons such as lower labor costs or more favorable economic conditions in that other country. The project describes the evolution of offshoring, which started in 1960’s and has continued since then; it was characterized primarily by the transferring of factories from the develope...

Boundary Spanning in Offshored Information Systems Development Projects

Science.gov (United States)

Krishnan, Poornima

2010-01-01

Recent growth in offshore outsourcing of information systems (IS) services is accompanied by managing the offshore projects successfully. Much of the project failures can be attributed to geographic and organizational boundaries which create differences in culture, language, work patterns, and decision making processes among the offshore project…

Lake Michigan Offshore Wind Feasibility Assessment

Energy Technology Data Exchange (ETDEWEB)

Boezaart, Arnold [GVSU; Edmonson, James [GVSU; Standridge, Charles [GVSU; Pervez, Nahid [GVSU; Desai, Neel [University of Michigan; Williams, Bruce [University of Delaware; Clark, Aaron [GVSU; Zeitler, David [GVSU; Kendall, Scott [GVSU; Biddanda, Bopi [GVSU; Steinman, Alan [GVSU; Klatt, Brian [Michigan State University; Gehring, J. L. [Michigan State University; Walter, K. [Michigan State University; Nordman, Erik E. [GVSU

2014-06-30

The purpose of this project was to conduct the first comprehensive offshore wind assessment over Lake Michigan and to advance the body of knowledge needed to support future commercial wind energy development on the Great Lakes. The project involved evaluation and selection of emerging wind measurement technology and the permitting, installation and operation of the first mid-lake wind assessment meteorological (MET) facilities in Michigan’s Great Lakes. In addition, the project provided the first opportunity to deploy and field test floating LIDAR and Laser Wind Sensor (LWS) technology, and important research related equipment key to the sitting and permitting of future offshore wind energy development in accordance with public participation guidelines established by the Michigan Great Lakes Wind Council (GLOW). The project created opportunities for public dialogue and community education about offshore wind resource management and continued the dialogue to foster Great Lake wind resource utilization consistent with the focus of the GLOW Council. The technology proved to be effective, affordable, mobile, and the methods of data measurement accurate. The public benefited from a substantial increase in knowledge of the wind resources over Lake Michigan and gained insights about the potential environmental impacts of offshore wind turbine placements in the future. The unique first ever hub height wind resource assessment using LWS technology over water and development of related research data along with the permitting, sitting, and deployment of the WindSentinel MET buoy has captured public attention and has helped to increase awareness of the potential of future offshore wind energy development on the Great Lakes. Specifically, this project supported the acquisition and operation of a WindSentinel (WS) MET wind assessment buoy, and associated research for 549 days over multiple years at three locations on Lake Michigan. Four research objectives were defined for the

Offshore wind resources at Danish measurement sites

Energy Technology Data Exchange (ETDEWEB)

Barthelmie, R J; Courtney, M S; Lange, B; Nielsen, M; Sempreviva, A M [Risoe National Lab., Dept. of Wind Energy and Atmospheric Physics, Roskilde (Denmark); Svenson, J; Olsen, F [SEAS, Haslev (Denmark); Christensen, T [Elsamprojekt, Fredericia (Denmark)

1999-03-01

In order to characterise wind and turbulence characteristics at prospective offshore wind energy sites, meteorological observations from a number of purpose-built offshore monitoring sites have been analyzed and compared with long wind speed time series. New analyses have been conducted on the data sets focussing on meteorology, turbulence, extreme winds and wind and wave interactions. Relationships between wind speed, turbulence and fetch are highly complex. Minimum turbulence intensity offshore is associated with wind speeds of about 12 m/s. At lower wind speeds, stability effects are important while at higher winds speeds wind and wave interactions appear to dominate. On average, turbulence intensity offshore at 48 m height is approximately 0.08 if no coastal effects are present. However, the effect of the coastal discontinuity persists in wind speed and turbulence characteristics for considerable distances offshore. The majority of the adjustment of appears to occur within 20 km of the coast. (au)

Offshore Vendors’ Software Development Team Configurations

DEFF Research Database (Denmark)

Chakraborty, Suranjan; Sarker, Saonee; Rai, Sudhanshu

2012-01-01

This research uses configuration theory and data collected from a major IT vendor organization to examine primary configurations of distributed teams in a global off-shoring context. The study indicates that off-shoring vendor organizations typically deploy three different types of configurations...

46 CFR 15.520 - Mobile offshore drilling units.

Science.gov (United States)

2010-10-01

... 46 Shipping 1 2010-10-01 2010-10-01 false Mobile offshore drilling units. 15.520 Section 15.520... REQUIREMENTS Manning Requirements; Inspected Vessels § 15.520 Mobile offshore drilling units. (a) The requirements in this section for mobile offshore drilling units (MODUs) supplement other requirements in this...

EWeA Offshore 2013 - Side event: 'Offshore wind energy - Potentialities and industrial opportunities in France and in Germany. French-German cross perspectives

International Nuclear Information System (INIS)

Genachte, Anne-Benedicte; Kavafyan, Philippe; Wagner, Andreas; Bour, Gregoire

2013-01-01

At the EWEA Offshore 2013 exhibition, the French-German office for Renewable energies (OFAEnR) organised a side-conference on Offshore wind energy and its Potentialities and industrial opportunities in France and in Germany. In the framework of this French-German exchange of experience, about 50 participants exchanged views on the conditions for the development of a durable offshore wind energy industry both in France and in Germany. This document brings together the available presentations (slides) made during this event: 1 - Supporting industrial development of offshore wind in Europe (Anne-Benedicte Genachte); 2 - Offshore wind energy: the Bremerhaven experience. An asset for the deployment of a complete industrial field in France (Philippe Kavafyan); 3 - Status, Prospects and Challenges for Offshore Wind energy in Germany - incl. Legal Framework and Presentation of cost reduction study results (Andreas Wagner); 4 - Offshore grid connection in Germany - Challenges and recommendations (Gregoire Bour)

Impact of convection over the equatorial trough on the summer monsoon activity over India

Digital Repository Service at National Institute of Oceanography (India)

RameshKumar, M.R.; Shenoi, S.S.C.; Schulz, J.

. There have been studies (Cadet and Olory Togbe, 1981; Sadhuram and Sastry, 1987) on the role of Equatorial Trough (ET) as well as Southern Hemispheric Equatorial Trough (SHET) on the rainfall over central India. Most of these studies are related... the ET, WET and EET behave in a similar fashion during different monsoon and El Nino conditions ? c) What role do the synoptic systems play during the BM over the Indian subcontinent? 2. Data and Methodology The pentad precipitation data used...

The EU Offshore Safety Directive and its potential effects. Opportunity or handicap?; Die EU Offshore Safety Directive und ihre moeglichen Auswirkungen. Chance oder Handicap?

Energy Technology Data Exchange (ETDEWEB)

Schwiederowski, Claudia [RWE Dea AG, Hamburg (Germany)

2014-07-01

The purpose of the EU Offshore Safety Directive, which took effect on 18 July 2013, is to define minimum requirements for the prevention of severe accidents in connection with offshore crude oil or natural gas activities of any kind and the containment of the follow-on effects of such accidents. This is without question a logical consequence of the offshore incidents seen around the globe over the past decades. An interesting question in this context is for whom the EU Offshore Safety Directive has become an opportunity and for whom a handicap. [German] Ziel der am 18. Juli 2013 in Kraft getretenen EU Offshore Safety Direktive ist die Festlegung von Mindestanforderungen fuer die Verhinderung schwerer Unfaelle bei Offshore-Erdoel- bzw. - Erdgasaktivitaeten und die Begrenzung etwaiger Unfallfolgen. Nach den weltweiten Offshore- Ereignissen der vergangenen Jahrzehnte ist dies ohne Zweifel eine logische Entwicklung. Nun stellt sich die Frage: Fuer wen entwickelt sich die EU Offshore Safety Directive zur Chance, fuer wen zum Handicap?.

A comparison of the relative locations of the mid-latitude electron density trough and the scintillation boundary

International Nuclear Information System (INIS)

Tulunay, Y.K.; Demir, O.; Tauriainen, A.

1976-01-01

The mid-latitude electron density trough position and the scintillation boundary have been compared for magnetically quiet periods by using the data returned by Ariel 3 and Explorer 22 satellites. The scintillation boundary is found southward of the trough during daytime, but at night the positions are reversed. (author)

The offshorization of economy: the present realities

Directory of Open Access Journals (Sweden)

Maslak Olga

2017-01-01

Full Text Available In this article the essence and main types of offshore zones have been studied. It has been analyzed the main reasons for cooperation with the tax havens, established that the main reason of the Ukrainian economy offshorization is not only the desire of economic entities to optimize taxes, but also the desire to protect their assets from the negative impact of the crisis phenomena in the national economy during 2010-2016. The foreign experience of the anti-offshore regulation has been researched. It has been defined that the general anti-offshore regulation vector should be based on the principles of financial transparency, active cooperation with the international community, an optimal combination of instruments that restrict the capital outflows and the effective instruments that stimulate the business development in the country. It has been also established that the mechanism of deoffshorization should be aimed not only at elimination of the territories with the preferential taxation, but also at receiving benefits from their use on the basis of the existing financial infrastructure of the leading world offshore centers. The experience of China in attracting additional foreign investments, gaining wider access to financial resources through the cooperation with an offshore financial centre has been researched.

Offshoring and financial markets

Directory of Open Access Journals (Sweden)

Gianfranco Battisti

2014-06-01

Full Text Available The paper analyses the nature and extent of the offshore world, a grey area that is playing a major role in present-day economy. The main institutions moulding this peculiar environment are discussed: preferential tax regimes, tax havens and offshore financial centers. Their role in the globalised world is outlined after a scrutiny of the specialized literature, reports by non-governmental bodies and companies’ advertisings. Finally, we present a tentative reconstruction of its geographical organization, inclusive of cartographic representations of the main international networks.

31 CFR 587.406 - Offshore transactions.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Offshore transactions. 587.406 Section 587.406 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) OFFICE... MONTENEGRO) MILOSEVIC SANCTIONS REGULATIONS Interpretations § 587.406 Offshore transactions. The prohibitions...

Project alliancing in the offshore industry

NARCIS (Netherlands)

Halman, Johannes I.M.; Braks, B.F.M.

In this paper the shift towards new types of project organisation within the Offshore Industry is explained and discussed. Special focus is given to the organisational concept of Project Alliancing. The principles, structure and culture of a Project Alliance as applied within the Offshore Industry

Initial dose of vancomycin based on body weight and creatinine clearance to minimize inadequate trough levels in Japanese adults.

Science.gov (United States)

Maki, N; Ohkuchi, A; Tashiro, Y; Kim, M R; Le, M; Sakamoto, T; Matsubara, S; Hakamata, Y

2012-10-01

Our aims were to elucidate the factors that affected vancomycin (VCM) serum trough levels and to find the optimal initial dose based on creatinine clearance (CrCl) and body weight (BW) to minimize inadequate trough levels in a retrospective observational study among Japanese adults. One hundred and six inpatients, in whom VCM trough levels were measured after completing the third dosing, were consecutively recruited into our study in a tertiary hospital. We considered the frequency of initial VCM total daily dose, CrCl, and BW were independent risk factors of VCM trough levels. In patients with CrCl ≥30 and level of ≥20 mcg/mL, regardless of BW. In patients with CrCl ≥50 mL/min, 2 g/day yielded low frequencies of a trough level of initial total daily dose may be 1 g/day in patients with CrCl ≥30 and <50 mL/min regardless of BW and 2 g/day in patients weighing <55 kg with CrCl ≥50 mL/min among Japanese adults.

Screening Criteria and Considerations of Offshore Enhanced Oil Recovery

Directory of Open Access Journals (Sweden)

Pan-Sang Kang

2016-01-01

Full Text Available The application of enhanced oil recovery (EOR in offshore oil fields has received significant attention due to the potentially enormous amount of recoverable oil. However, EOR application offshore is in its very early stage due to conditions that are more complex than onshore oil fields, owing to the unique parameters present offshore. Therefore, successful EOR applications in offshore oil fields require different screening criteria than those for conventional onshore applications. A comprehensive database for onshore applications of EOR processes together with a limited offshore EOR application database are analyzed in this paper, and the important parameters for successful offshore application are incorporated into the new EOR screening criteria. In this paper, screening criteria to determine acceptable EOR processes for offshore fields, including hydrocarbon gas miscible, CO2 miscible, and polymer processes, are presented. Suggested screening criteria for these EOR processes comprise quantitative boundaries and qualitative considerations. Quantitative screening criteria are predominantly based on quantifiable data, such as oil and reservoir properties. Qualitative screening considerations mainly focus on the operational issues present offshore, including platform space constraints, limited disposal options, injectant availability, and flow assurance matters (including hydrate formation and difficulties in emulsion separation.

Energy Usage of Residents on Offshore Islands in Taiwan

Directory of Open Access Journals (Sweden)

Szu-Cheng Lu

2015-05-01

Full Text Available A field study was conducted through interviews on offshore islands in Taiwan to investigate the energy usage of local residents. A comparison of household appliance usage in mainland Taiwan with that on the offshore islands revealed that, overall, the most commonly used household appliances are steam cookers/rice cookers, water dispensers, and washing machines. For other household appliances, Levels 2 and 3 offshore isles have lower use penetration rates compared with those in mainland Taiwan and on Level 1 offshore isles, particularly for the use of computers. By contrast, the use penetration rate for chest freezers on Levels 2 and 3 offshore isles is high, and each household has one or more freezers on average. This appliance is not a commonly observed household product in mainland Taiwan or on Level 1 offshore isles. Furthermore, because of the government policy, every household on parts of Level 2 offshore isles and on all Level 3 offshore isles has a fixed monthly charge of electricity. The transportation of liquefied petroleum gas is also inconvenient, and the gas price is slightly higher, leading to the tendency of residents to consume excessive amounts of electrical energy, which does not correspond with the aim of the government to conserve energy and reduce carbon emissions; thus, the relevant authorities’ review and improvement on energy consumption on Levels 2 and 3 offshore isles are required.

Sensitivity analysis of floating offshore wind farms

International Nuclear Information System (INIS)

Castro-Santos, Laura; Diaz-Casas, Vicente

2015-01-01

Highlights: • Develop a sensitivity analysis of a floating offshore wind farm. • Influence on the life-cycle costs involved in a floating offshore wind farm. • Influence on IRR, NPV, pay-back period, LCOE and cost of power. • Important variables: distance, wind resource, electric tariff, etc. • It helps to investors to take decisions in the future. - Abstract: The future of offshore wind energy will be in deep waters. In this context, the main objective of the present paper is to develop a sensitivity analysis of a floating offshore wind farm. It will show how much the output variables can vary when the input variables are changing. For this purpose two different scenarios will be taken into account: the life-cycle costs involved in a floating offshore wind farm (cost of conception and definition, cost of design and development, cost of manufacturing, cost of installation, cost of exploitation and cost of dismantling) and the most important economic indexes in terms of economic feasibility of a floating offshore wind farm (internal rate of return, net present value, discounted pay-back period, levelized cost of energy and cost of power). Results indicate that the most important variables in economic terms are the number of wind turbines and the distance from farm to shore in the costs’ scenario, and the wind scale parameter and the electric tariff for the economic indexes. This study will help investors to take into account these variables in the development of floating offshore wind farms in the future

Offshore Aquaculture: I Know It When I See It

Directory of Open Access Journals (Sweden)

Halley E. Froehlich

2017-05-01

Full Text Available Offshore aquaculture is increasingly viewed as a mechanism to meet growing protein demand for seafood, while minimizing adverse consequences on the environment and other uses in the oceans. However, despite growing interest in offshore aquaculture, there appears to be no consensus as to what measures commonly define an offshore site or how effects of offshore aquaculture—relative to more nearshore practices—are assessed. This lack of agreement on what constitutes offshore aquaculture has the potential to convolute communication, create uncertainty in regulatory processes, and impede understanding of the ecological implications of offshore farming. To begin addressing these issues, we reviewed and analyzed biologically-focused primary and gray literature (Ntotal = 70 that categorize and quantify characteristics of offshore aquaculture from around the world. We found that many “offshore” descriptions are relatively close to shore (<3 nm and significantly shallower (minimum depth ≤30 m than may be assumed. We also uncovered an overall lack of consistent reporting of even the most common location-focused metrics (distance from shore, depth, current, a dearth of impact related studies (n = 17, and narrow scope of the studies themselves (i.e., 82% nutrient pollution. Of the finite subset of articles that investigated negative ecological impacts of offshore aquaculture, we found the probability of any measurable impact from an offshore farm appears to significantly decrease with distance from the farm (probability of measurable response at 90 m ± SE = 0.01 ± 0.03. Such general, but informative points of reference could be more robustly quantified with better systematic and standardized reporting of physical farm characteristics and a broader scope of ecological investigation into the effects of marine aquaculture. With offshore aquaculture still in its infancy, consistent metrics are needed for a comparable framework to guide sustainable

Investigation on the dynamic behaviour of a parabolic trough power plant during strongly cloudy days

International Nuclear Information System (INIS)

Al-Maliki, Wisam Abed Kattea; Alobaid, Falah; Starkloff, Ralf; Kez, Vitali; Epple, Bernd

2016-01-01

Highlights: • A detailed dynamic model of a parabolic trough solar thermal power plant is done. • Simulated results are compared to the experimental data from the real power plant. • Discrepancy between model result and real data is caused by operation strategy. • The model strategy increased the operating hours of power plant by around 2.5–3 h. - Abstract: The objective of this study is the development of a full scale dynamic model of a parabolic trough power plant with a thermal storage system, operated by the Actividades de Construcción y Servicios Group in Spain. The model includes solar field, thermal storage system and the power block and describes the heat transfer fluid and steam/water paths in detail. The parabolic trough power plant is modelled using Advanced Process Simulation Software (APROS). To validate the model, the numerical results are compared to the measured data, obtained from “Andasol II” during strongly cloudy periods in the summer days. The comparisons show a qualitative agreement between the dynamic simulation model and the measurements. The results confirm that the thermal storage enables the parabolic trough power plant to provide a constant power rate when the storage energy discharge is available, despite significant oscillations in the solar radiation.

Many play concepts seen over wide area in Erris, Slyne troughs off Ireland

International Nuclear Information System (INIS)

Murphy, N.J.; Croker, P.F.

1992-01-01

This paper reports that the Erris and Slyne troughs are underexplored Mesozoic sedimentary basins off Ireland's northwest coast. The Irish Minister for Energy announced on Apr. 19, 1991, a frontier acreage licensing round of 128 blocks covering 29,000 sq km in these basins and the adjacent Rockall trough. Closing date for the round is June 30, 1993, set to allow two seasons for the acquisition of new geophysical and geological data over the area. Ireland has recently announced a new petroleum taxation regime. Revised licensing terms, which will acknowledge the specific circumstances of frontier acreage, will be announced

Canadian East Coast offshore petroleum industry safe lifting practices respecting offshore pedestal cranes, offshore containers, loose gear, other lifting devices, and operational best practices : standard practices

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-11-15

This document was developed by a working group with representatives from the petroleum industry, the Offshore Petroleum Boards and Certifying Authorities. It outlines industry best practices for operators responsible for the management, planning and execution of offshore lifting operations. Its purpose is to assist in the interpretation of applicable legislation and standards. Considered within the practice are safe design requirements, manufacture, certification, testing, maintenance and inspection requirements for pedestal cranes, offshore containers, loose gear and lifting devices. Operational best practices for lifting operations are also included along with a section that identifies additional requirements for personnel lifting operations, including personnel transfers by crane and man-riding operations. 82 refs., 2 tabs., 4 figs., 3 appendices.

31 CFR 544.406 - Offshore transactions.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Offshore transactions. 544.406 Section 544.406 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) OFFICE... SANCTIONS REGULATIONS Interpretations § 544.406 Offshore transactions. The prohibitions in § 544.201 on...

31 CFR 593.406 - Offshore transactions.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Offshore transactions. 593.406 Section 593.406 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) OFFICE... SANCTIONS REGULATIONS Interpretations § 593.406 Offshore transactions. The prohibitions in § 593.201 on...

31 CFR 541.406 - Offshore transactions.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Offshore transactions. 541.406 Section 541.406 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) OFFICE... § 541.406 Offshore transactions. The prohibitions in § 541.201 on transactions involving blocked...

31 CFR 537.406 - Offshore transactions.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Offshore transactions. 537.406 Section 537.406 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) OFFICE... § 537.406 Offshore transactions. The prohibitions in § 537.201 on transactions involving blocked...

31 CFR 542.406 - Offshore transactions.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Offshore transactions. 542.406 Section 542.406 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) OFFICE... § 542.406 Offshore transactions. The prohibitions in § 542.201 on transactions involving blocked...

Spatial and temporal distribution of pore gas concentrations during mainstream large-scale trough composting in China.

Science.gov (United States)

Zeng, Jianfei; Shen, Xiuli; Sun, Xiaoxi; Liu, Ning; Han, Lujia; Huang, Guangqun

2018-05-01

With the advantages of high treatment capacity and low operational cost, large-scale trough composting has become one of the mainstream composting patterns in composting plants in China. This study measured concentrations of O 2 , CO 2 , CH 4 and NH 3 on-site to investigate the spatial and temporal distribution of pore gas concentrations during mainstream large-scale trough composting in China. The results showed that the temperature in the center of the pile was obviously higher than that in the side of the pile. Pore O 2 concentration rapidly decreased and maintained composting process during large-scale trough composting when the pile was naturally aerated, which will contribute to improving the current undesirable atmosphere environment in China. Copyright © 2018 Elsevier Ltd. All rights reserved.

Geochemical and isotopic characteristics of volcanic rocks from the northern East China Sea shelf margin and the Okinawa Trough

Institute of Scientific and Technical Information of China (English)

ZENG Zhigang; YU Shaoxiong; WANG Xiaoyuan; FU Yongtao; YIN Xuebo; ZHANG Guoliang; WANG Xiaomei; CHEN Shuai

2010-01-01

Volcanic rocks both from the northern East China Sea (NECS) shelf margin and the northern Okinawa Trough are subalkaline less aluminous,and lower in High Field Strength Elements (HFSE).These rocks are higher in Large Ion Lithophile Elements (LILE),thorium and uranium contents,positive lead anomalies,negative Nb-Ta anomalies,and enrichment in Light Rare Earth Elements (LREE).Basalts from the NECS shelf margin are akin to Indian Ocean Mid-Ocean Ridge Basalt (MORB),and rhyolites from the northern Okinawa Trough have the highest 207Pb/204Pb and 208Pb/204Pb ratios.The NECS shelf margin basalts have lower 87Sr/86Sr ratios,εNd and σ18O than the northern Okinawa Trough silicic rocks.According to 40K-40Ar isotopic ages of basalts from the NECS shelf margin,rifting of the Okinawa Trough may have been active since at least 3.65-3.86 Ma.The origin of the NECS shelf margin basalt can be explained by the interaction of melt derived from Indian Ocean MORB-like mantle with enriched subcontinental lithosphere.The basalts from both sides of the Okinawa Trough may have a similar origin during the initial rifting of the Okinawa Trough,and the formation of basaltic magmas closely relates to the thinning of continental crust.The source of the formation of the northern Okinawa Trough silicic rocks was different from that of the middle Okinawa Trough,which could have been generated by the interaction of basaltic melt with an enriched crustal component.From the Ryukyu island arc to East China,the Cenozoic basalts have apparently increasing trends of MgO contents and ratios of LREE to Heavy Rare Earth Elements (HREE),suggesting that the trace element variabilities of basalts may have been influenced by the subduction of the Philippine Sea plate,and that the effects of subduction of the Philippine Sea plate on the chemical composition of basaltic melts have had a decreasing effect from the Ryukyu island arc to East China.

Study on a Mid-Temperature Trough Solar Collector with Multisurface Concentration

Directory of Open Access Journals (Sweden)

Zhengliang Li

2015-01-01

Full Text Available A new trough solar concentrator which is composed of multiple reflection surfaces is developed in this paper. The concentrator was analyzed firstly by using optical software. The variation curves of the collecting efficiency affected by tracking error and the deviation angle were given out. It is found that the deviation tolerance for the collector tracking system is about 8 degrees when the receiver is a 90 mm flat. The trough solar concentrators were tested under real weather conditions. The experiment results indicate that, the new solar concentrator was validated to have relative good collecting efficiency, which can be more than 45 percent when it operated in more 145°C. It also has the characteristics of rdust, wind, and snow resistance and low tracking precision requirements.

Studies of sporadic E (Es) associated with the main ionospheric trough

International Nuclear Information System (INIS)

Rodger, A.S.; Morrell, C.; Dudeney, J.R.

1983-01-01

Sporadic E, or E(s) events under the main F region trough have been confirmed on the basis of ionograms from a vertical incidence ionosonde at Halley Bay, Antarctica. Analyses indicate that E(s) is frequently observable under both the equatorward and the poleward edges of the trough, as well as poleward of it. Before magnetic midnight, E(s) layers whose semithickness resembles those of the normal E layer are common, in contrast to layers seen after magnetic midnight which show the characteristics of thin E(s) layers. A possible explanation of the observed change in the E(s) layer characteristics at magnetic midnight is related to differences in the type and spectra of the precipitating particles. It is shown that the redistribution of ionization by the convection electric field may be important. 40 references

Viewing engineering offshoring in a network perspective

DEFF Research Database (Denmark)

Hansen, Zaza Nadja Lee; Zhang, Yufeng; Ahmed-Kristensen, Saeema

2013-01-01

of how to effectively manage engineering offshoring activities in a context of global engineering networks. The main research question, therefore, is: “Can offshoring of engineering tasks be explained and managed using the concept of Global Engineering Networks (GEN)?” Effective approaches to handling...... of large multinational corporations in Denmark were carried out. Data gathering was mainly documentary studies and interviews. The main data analysis approaches were coding (Strauss and Corbin) and pattern-matching (Yin). The dataset was analysed using the GEN framework suggested by Zhang et al. and Zhang...... by extending the GEN framework to address complications within engineering offshoring. This strengthens both academic fields, and will be able to help engineering managers to develop appropriate engineering network configurations for offshore engineering operations....

Managing Hidden Costs of Offshoring

DEFF Research Database (Denmark)

Larsen, Marcus M.; Pedersen, Torben

2014-01-01

This chapter investigates the concept of the ‘hidden costs’ of offshoring, i.e. unexpected offshoring costs exceeding the initially expected costs. Due to the highly undefined nature of these costs, we position our analysis towards the strategic responses of firms’ realisation of hidden costs....... In this regard, we argue that a major response to the hidden costs of offshoring is the identification and utilisation of strategic mechanisms in the organisational design to eventually achieving system integration in a globally dispersed and disaggregated organisation. This is heavily moderated by a learning......-by-doing process, where hidden costs motivate firms and their employees to search for new and better knowledge on how to successfully manage the organisation. We illustrate this thesis based on the case of the LEGO Group....

Offshore Wind Turbine Design

DEFF Research Database (Denmark)

Frandsen, Sten; Hansen, Erik Asp; Ibsen, Lars Bo

2006-01-01

Current offshore wind turbine design methods have matured to a 1st generation state, manifested in the draft of a possible standard, IEC 61400-3 (2005). It is now time to investigate the possibilities of improving existing methods. To do so in an efficient manner a clear identification of the most...... important uncertainty drivers specific for offshore wind turbine design loads is required. Describing the initial efforts in a Danish research project, the paper points to focal points for research and development. These are mainly: soil-structure interaction, improved modelling of wave loads from deep...

Efficient promotion of electricity production from offshore wind; Effiziente Foerderung der Stromerzeugung aus Offshore-Wind

Energy Technology Data Exchange (ETDEWEB)

Panzer, Christian; Auer, Hans; Lettner, Georg [Technische Univ. Wien (Austria). Energy Economics Group (EEG)

2014-03-15

Efficient promotion of electricity production from offshore wind stands in dynamic relationship with various influence factors, the most important of which are promotion instruments, topographic givens, regulation of grid connection, and supraregional market integration concepts. Using three case studies from different countries to highlight national differences in the promotion of offshore wind power plants the present analysis points out ways of improving the efficiency of promotion instruments.

Offshore wind potential evaluation and remote sensing imagery; Evaluation du potentiel eolien offshore et imagerie satellitale

Energy Technology Data Exchange (ETDEWEB)

Fichaux, N.

2003-12-15

Offshore wind energy may help to contribute to the respect of the Kyoto objectives by Europe. It is a key issue to struggle against global change. To sit the future offshore wind parks, it is necessary to accurately evaluate the spatial repartition of the wind potential. We demonstrate that the offshore wind potential shall be represented by maps of wind statistics. As remote sensing is a tool for measuring space physical phenomena, we evaluate its potentialities for mapping wind statistics. Space-borne scatterometers enables the obtention of wind statistics, but far from our areas of interest and at low spatial resolution. Synthetic Aperture Radar (SAR) enables the computation of high resolution wind maps over our areas of interest, but are unsuitable to compute wind statistics. We define the mathematical framework of a statistical method. That method enables to take advantage of both scatterometer and SAR to compute maps of wind statistics at high spatial resolution over the areas of interest. It enables remote sensing to be used operationally to map the offshore wind potential. (author)

31 CFR 543.406 - Offshore transactions.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Offshore transactions. 543.406 Section 543.406 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) OFFICE... Interpretations § 543.406 Offshore transactions. The prohibitions in § 543.201 on transactions or dealings...

31 CFR 597.406 - Offshore transactions.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Offshore transactions. 597.406 Section 597.406 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) OFFICE... REGULATIONS Interpretations § 597.406 Offshore transactions. The prohibitions contained in § 597.201 apply to...

31 CFR 547.406 - Offshore transactions.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Offshore transactions. 547.406 Section 547.406 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) OFFICE... REGULATIONS Interpretations § 547.406 Offshore transactions. The prohibitions in § 547.201 on transactions or...

31 CFR 548.406 - Offshore transactions.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Offshore transactions. 548.406 Section 548.406 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) OFFICE... § 548.406 Offshore transactions. The prohibitions in § 548.201 on transactions or dealings involving...

31 CFR 546.406 - Offshore transactions.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Offshore transactions. 546.406 Section 546.406 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) OFFICE... § 546.406 Offshore transactions. The prohibitions in § 546.201 on transactions or dealings involving...

31 CFR 588.406 - Offshore transactions.

Science.gov (United States)

2010-07-01

... 31 Money and Finance: Treasury 3 2010-07-01 2010-07-01 false Offshore transactions. 588.406 Section 588.406 Money and Finance: Treasury Regulations Relating to Money and Finance (Continued) OFFICE... Interpretations § 588.406 Offshore transactions. The prohibitions in § 588.201 on transactions involving blocked...

Offshore Outlook: the European Side Perspectives offshore : le point de vue européen

Directory of Open Access Journals (Sweden)

Delacour J.

2006-11-01

Full Text Available The offshore hydrocarbon potential of Europe was fully revealed during the 1970s by various major discoveries which, after the first oil shock in 1973 and in the light of the high energy consumption in this zone, were a major asset in the new equilibria that would be found between producing and consuming countries. The offshore potential of Europe is concentrated in two zones: the North Sea and the Mediterranean. The North Sea, with the particularly harsh operating conditions, has quickly given rise to what can today be qualified as a new engineering state-of-the-art. At the same time, developments in the Mediterranean have brought a demonstration of entirely original and profitable petroleum achievements. For the future and despite current economic uncertainties, the outlook for European offshore development remain particularly attractive, obviously with regard to oil, but also, and more and more so, from the standpoint of natural gas. Le potentiel offshore en hydrocarbures de l'Europe a été pleinement mis en évidence au cours des années 70 par un certain nombre de grandes découvertes qui constituaient, après le premier choc pétrolier de 1973, compte tenu des fortes consommations d'énergie dans cette zone, un atout majeur dans les nouveaux équilibres qui s'instauraient entre pays producteurs et pays consommateurs. Le potentiel offshore de l'Europe se concentre sur deux zones : la mer du Nord et la Méditerranée. La mer du Nord, avec des conditions d'exploitation particulièrement sévères, a donné rapidement naissance à ce que l'on peut, aujourd'hui, qualifier de nouvel art de l'ingénieur, tandis que les développements en Méditerranée apportaient la démonstration de réalisations pétrolières tout à fait originales et profitables. Pour le futur, et malgré les incertitudes économiques actuelles, les perspectives de développement de l'offshore européen restent particulièrement attractives, au niveau du pétrole �

Baltic 2 offshore wind farm. Challenges and solutions during design and erection of a 288 MW offshore wind power plant; Baltic 2 Offshore Windpark. Herausforderungen und Loesungen waehrend der Design- und Errichtungsphase eines 288 MW Offshore-Windkraftwerks

Energy Technology Data Exchange (ETDEWEB)

Stamatelopoulos, Georg-Nikolaus; Kansy, Stefan [EnBW Energie Baden-Wuerttemberg AG, Stuttgart (Germany); Hannibal, John Michael [Siemens AG, Hamburg (Germany). Wind Power and Renewables Div.; Frettloehr, Bjoern [EnBW Energie Baden-Wuerttemberg AG, Hamburg (Germany). Wind und Maritime Technik

2015-05-01

Offshore wind offers a great potential for reliable power supply with markedly less future costs. However, offshore also means special requirements related to transport and installation at sea. Even if these requirements alone are very stringent, they are not the only ones that apply. Meeting these challenges requires project organisation comparable to other major projects.

Gravity Anomalies Over The Gongola Arm, Upper Benue Trough ...

African Journals Online (AJOL)

A regional gravity survey of the Gongola Arm of the Benue trough was carried out with the aim of determining structures of interest. The results of the gravity interpretation showed that the area of study is characterized by negative Bouguer anomalies that trend in the NE-SW direction and range in value from -75 to -15 mGal ...

The Organizational Design of Offshoring

DEFF Research Database (Denmark)

Ørberg Jensen, Peter D.; Larsen, Marcus M.; Pedersen, Torben

2013-01-01

Offshoring can be defined as the relocation of organizational tasks and services to foreign locations. At the same time as the scale and scope of offshoring have reached unprecedented levels in recent years, firms have increasingly been exposed to the challenges relating to managing an organizati...... implies an organizational reconfiguration consisting of three stages: disintegration, relocation and reintegration. We discuss the implications of this perspective and outline a research agenda....

Denmark - supplier of competitive offshore wind solutions. Megavind's strategy for offshore wind research, development and demonstration

Energy Technology Data Exchange (ETDEWEB)

2010-12-15

In May 2006, the Danish Government presented a report on promoting environmentally effective technology and established a number of innovative partnerships. The partnerships intend to strengthen public-private cooperation between the state, industry, universities and venture capital to accelerate innovation for a number of green technologies. The partnership for wind energy is called Megavind. Megavind's strategy for offshore wind describes the offshore challenges and suggests research, development and demonstration (RD and D) priorities to enable offshore wind power become to competitive with other energy technologies. The strategy lists key recommendations as well as key thematic priorities and for each of these a number of RD and D priorities. Under each thematic priority references are made to the European Strategic Energy Technology plan (SET-plan), which prioritises offshore wind RD and D in Europe. (LN)

Assessing the impact of Hurricanes Irene and Sandy on the morphology and modern sediment thickness on the inner continental shelf offshore of Fire Island, New York

Science.gov (United States)

Schwab, William C.; Baldwin, Wayne E.; Denny, Jane F.

2016-01-15

This report documents the changes in seabed morphology and modern sediment thickness detected on the inner continental shelf offshore of Fire Island, New York, before and after Hurricanes Irene and Sandy made landfall. Comparison of acoustic backscatter imagery, seismic-reflection profiles, and bathymetry collected in 2011 and in 2014 show that sedimentary structures and depositional patterns moved alongshore to the southwest in water depths up to 30 meters during the 3-year period. The measured lateral offset distances range between about 1 and 450 meters with a mean of 20 meters. The mean distances computed indicate that change tended to decrease with increasing water depth. Comparison of isopach maps of modern sediment thickness show that a series of shoreface-attached sand ridges, which are the dominant sedimentary structures offshore of Fire Island, migrated toward the southwest because of erosion of the ridge crests and northeast-facing flanks as well as deposition on the southwest-facing flanks and in troughs between individual ridges. Statistics computed suggest that the modern sediment volume across the about 81 square kilometers of common sea floor mapped in both surveys decreased by 2.8 million cubic meters, which is a mean change of –0.03 meters, which is smaller than the resolution limit of the mapping systems used.

Offshoring in the Semiconductor Industry: Historical Perspectives

OpenAIRE

Brown, Clair; Linden, Greg

2005-01-01

Semiconductor design is a frequently-cited example of the new wave of offshoring and foreign-outsourcing of service sector jobs. It is certainly a concern to U.S. design engineers themselves. In addition to the current wave of white-collar outsourcing, the industry also has a rich experience with offshoring of manufacturing activity. Semiconductor companies were among the first to invest in offshore facilities to manufacture goods for imports back to the U.S. A brief review of these earlie...

The offshorization of economy: the present realities

OpenAIRE

Maslak Olga; Grishko Natalya; Hlazunova Olha; Vorobiova Kateryna

2017-01-01

In this article the essence and main types of offshore zones have been studied. It has been analyzed the main reasons for cooperation with the tax havens, established that the main reason of the Ukrainian economy offshorization is not only the desire of economic entities to optimize taxes, but also the desire to protect their assets from the negative impact of the crisis phenomena in the national economy during 2010-2016. The foreign experience of the anti-offshore regulation has been researc...

Switching overvoltages in offshore wind power grids

DEFF Research Database (Denmark)

Arana Aristi, Ivan

and cables are presented. In Chapter 4 results from time domain measurements and simulations of switching operations in offshore wind power grids are described. Specifically, switching operations on a single wind turbine, the collection grid, the export system and the external grid measured in several real...... offshore wind farms are shown together with simulation results. Switching operations in offshore wind power grids can be simulated with different electromagnetic transient programs. Different programs were used in the project and compared results are included in Chapter 4. Also in Chapter 4 different......Switching transients in wind turbines, the collection grid, the export system and the external grid in offshore wind farms, during normal or abnormal operation, are the most important phenomena when conducting insulation coordination studies. However, the recommended models and methods from...

Model and control scheme for recirculation mode direct steam generation parabolic trough solar power plants

International Nuclear Information System (INIS)

Guo, Su; Liu, Deyou; Chen, Xingying; Chu, Yinghao; Xu, Chang; Liu, Qunming; Zhou, Ling

2017-01-01

Highlights: •A nonlinear dynamic model of recirculation DSG parabolic trough is developed. •Collector row, water separator and spray attemperator are modeled, respectively. •The dynamic behaviors of the collector field are simulated and analyzed. •Transfer functions of water level and outlet fluid temperature are derived. •Multi-model switching generalized predictive control strategy is developed. -- Abstract: This work describes and evaluates a new nonlinear dynamic model, and a new generalized predictive control scheme for a collector field of direct steam generation parabolic troughs in recirculation mode. Modeling the dynamic behaviors of collector fields is essential to design, testing and validation of automatic control systems for direct steam generation parabolic troughs. However, the behaviors of two-phase heat transfer fluids impose challenges to simulating and developing process control schemes. In this work, a new nonlinear dynamic model is proposed, based on the nonlinear distributed parameter and the nonlinear lumped parameter methods. The proposed model is used to simulate and analyze the dynamic behaviors of the entire collector field for recirculation mode direct steam generation parabolic troughs under different weather conditions, without excessive computational costs. Based on the proposed model, transfer functions for both the water level of the separator and outlet steam temperatures are derived, and a new multi-model switching generalized predictive control scheme is developed for simulated control of the plant behaviors for a wide region of operational conditions. The proposed control scheme achieves excellent control performance and robustness for systems with long delay, large inertia and time-varying parameters, and efficiently solves the model mismatching problem in direct steam generation parabolic troughs. The performances of the model and control scheme are validated with design data from the project of Integration of Direct

Soil-Structure Interaction for Non-Slender, Large-Diameter Offshore Monopiles

DEFF Research Database (Denmark)

Sørensen, Søren Peder Hyldal

Offshore wind power is a domestic, sustainable and largely untapped energy resource. Today, the modern offshore wind turbine offers competitive production prices compared to other sources of renewable energy. Therefore, it is a key technology in breaking the dependence on fossil fuels...... and in achieving the energy and climate goals of the future. For offshore wind turbines, the costs of foundation typically constitute 20-30% of the total costs. Hence, improved methods for the design of foundations for offshore wind turbines can increase the competitiveness of offshore wind energy significantly....... The monopile foundation concept has been employed as the foundation for the majority of the currently installed offshore wind turbines. Therefore, this PhD thesis concerns the soil-pile interaction for non-slender, large-diameter offshore piles. A combination of numerical and physical modelling has been...

Modeling of a Parabolic Trough Solar Field for Acceptance Testing: A Case Study

Energy Technology Data Exchange (ETDEWEB)

Wagner, M. J.; Mehos, M. S.; Kearney, D. W.; McMahan, A. C.

2011-01-01

As deployment of parabolic trough concentrating solar power (CSP) systems ramps up, the need for reliable and robust performance acceptance test guidelines for the solar field is also amplified. Project owners and/or EPC contractors often require extensive solar field performance testing as part of the plant commissioning process in order to ensure that actual solar field performance satisfies both technical specifications and performance guaranties between the involved parties. Performance test code work is currently underway at the National Renewable Energy Laboratory (NREL) in collaboration with the SolarPACES Task-I activity, and within the ASME PTC-52 committee. One important aspect of acceptance testing is the selection of a robust technology performance model. NREL1 has developed a detailed parabolic trough performance model within the SAM software tool. This model is capable of predicting solar field, sub-system, and component performance. It has further been modified for this work to support calculation at subhourly time steps. This paper presents the methodology and results of a case study comparing actual performance data for a parabolic trough solar field to the predicted results using the modified SAM trough model. Due to data limitations, the methodology is applied to a single collector loop, though it applies to larger subfields and entire solar fields. Special consideration is provided for the model formulation, improvements to the model formulation based on comparison with the collected data, and uncertainty associated with the measured data. Additionally, this paper identifies modeling considerations that are of particular importance in the solar field acceptance testing process and uses the model to provide preliminary recommendations regarding acceptable steady-state testing conditions at the single-loop level.

Benthic foraminifera and bottom water evolution in the middle-southern Okinawa Trough during the last 18 ka

Institute of Scientific and Technical Information of China (English)

LI Tiegang; XIANG Rong; SUN Rongtao; CAO Qiyuan

2005-01-01

A piston sediment core E017 from the middle-southern Okinawa Trough was investigated. A preliminary study of the deep-water evolution since 18 cal. ka BP was performed based on the quantitative census data of benthic foraminiferal fauna, together with planktonic foraminiferal oxygen and carbon isotope, AMS14C dating, and the previous results achieved in the southern Okinawa Trough. The result shows that the benthic fauna was dominated by Bulimina aculeata (d'Orbigny), Uvigerina peregrina (Cushman), Hispid Uvigerina and Uvigerina dirupta (Todd) during the glaciation-deglaciation before 9.2 cal. ka BP, while Epistominella exigua (Brady), Pullenia bulloides (d'Orbigny), Cibicidoides hyalina (Hofker), Sphaeroidina bulloides (d'Orbigny) and Globocassidulina subglobosa (Brady) predominated the fauna in the post-glacial period after 9.2 cal. ka BP. The benthic foraminifera accumulation rate (BFAR), paleoproductivity estimates and benthic foraminiferal assemblage conformably indicate that surface water paleoproductivity and organic matter flux during the glaciation-deglaciation were higher than those of the post-glacial period in the middle-southern Okinawa Trough, and gradually enhanced from the southern to the central Okinawa Trough during the glaciation-deglaciation, which could be caused by the discrepancy of the terrigenous nutrients supply. High abundances of E. exigua, an indicator of pulsed organic matter input, after 9.2 cal. ka BP may indicate that the intensity of seasonally riverine pulsed flux during the post-glacial period was stronger than that of the glaciation-deglaciation period, and the seasonal influx in the central trough might be stronger than in the south. The temporal distributions of the typical species indicating bottom water oxygen content and ventilation condition show that the ventilation of the bottom water during the post-glacial period is more active than the glaciation-deglaciation, which reflects that the evolution of the intermediate and

Real-time dynamic analysis for complete loop of direct steam generation solar trough collector

International Nuclear Information System (INIS)

Guo, Su; Liu, Deyou; Chu, Yinghao; Chen, Xingying; Shen, Bingbing; Xu, Chang; Zhou, Ling; Wang, Pei

2016-01-01

Highlights: • A nonlinear distribution parameter dynamic model has been developed. • Real-time local heat transfer coefficient and friction coefficient are adopted. • The dynamic behavior of the solar trough collector loop are simulated. • High-frequency chattering of outlet fluid flow are analyzed and modeled. • Irradiance disturbance at subcooled water region generates larger influence. - Abstract: Direct steam generation is a potential approach to further reduce the levelized electricity cost of solar trough. Dynamic modeling of the collector loop is essential for operation and control of direct steam generation solar trough. However, the dynamic behavior of fluid based on direct steam generation is complex because of the two-phase flow in the pipeline. In this work, a nonlinear distribution parameter model has been developed to model the dynamic behaviors of direct steam generation parabolic trough collector loops under either full or partial solar irradiance disturbance. Compared with available dynamic model, the proposed model possesses two advantages: (1) real-time local values of heat transfer coefficient and friction resistance coefficient, and (2) considering of the complete loop of collectors, including subcooled water region, two-phase flow region and superheated steam region. The proposed model has shown superior performance, particularly in case of sensitivity study of fluid parameters when the pipe is partially shaded. The proposed model has been validated using experimental data from Solar Thermal Energy Laboratory of University of New South Wales, with an outlet fluid temperature relative error of only 1.91%. The validation results show that: (1) The proposed model successfully outperforms two reference models in predicting the behavior of direct steam generation solar trough. (2) The model theoretically predicts that, during solar irradiance disturbance, the discontinuities of fluid physical property parameters and the moving back and

Visual disamenities from off-shore wind farms in Denmark

DEFF Research Database (Denmark)

Ladenburg, Jacob; Dubgaard, Alex; Tranberg, Jesper

2006-01-01

Expansion of the off-shore wind power plays a significant role in the energy policies of many EU countries. However, off-shore wind farms create visual disamenities. These disamenities can be reduced by locating wind farms at larger distances from the coast – and accepting higher costs per k......Wh produced. Base on the choices among alternative wind farm outlays, the preferences for reducing visual disamenities of off-shore wind farms were elicited using the Choice Experiment Method. The results show a clear picture; the respondents in three independent samples are willing to pay for mowing future...... off-shore wind farms away from the shore to reduce the wind farms visibility. However, the results also denote that the preferences vary with regards to the experiences with visual disamenities of off-shore wind farms. The respondents Horns Revs sample, where the off-shore wind farm is located...

Offshore Resource Assessment and Design Conditions: A Data Requirements and Gaps Analysis for Offshore Renewable Energy Systems

Energy Technology Data Exchange (ETDEWEB)

Elliott, Dennis [National Renewable Energy Lab. (NREL), Golden, CO (United States); Frame, Caitlin [National Oceanic and Atmospheric Administration (NOAA), Washington, DC (United States); Gill, Carrie [National Oceanic and Atmospheric Administration (NOAA), Washington, DC (United States); Hanson, Howard [Florida Atlantic Univ., Boca Raton, FL (United States); Moriarty, Patrick [National Renewable Energy Lab. (NREL), Golden, CO (United States); Powell, Mark [National Oceanic and Atmospheric Administration (NOAA), Washington, DC (United States); Shaw, William J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wilczak, Jim [National Oceanic and Atmospheric Administration (NOAA), Washington, DC (United States); Wynne, Jason [Energetics, Columbia, MD (United States)

2012-03-01

The offshore renewable energy industry requires accurate meteorological and oceanographic (“metocean”) data for evaluating the energy potential, economic viability, and engineering requirements of offshore renewable energy projects. It is generally recognized that currently available metocean data, instrumentation, and models are not adequate to meet all of the stakeholder needs on a national scale. Conducting wind and wave resource assessments and establishing load design conditions requires both interagency collaboration as well as valuable input from experts in industry and academia. Under the Department of Energy and Department of Interior Memorandum of Understanding, the Resource Assessment and Design Condition initiative supports collaborative national efforts by adding to core atmospheric and marine science knowledge relevant to offshore energy development. Such efforts include a more thorough understanding and data collection of key metocean phenomena such as wind velocity and shear; low-level jets; ocean, tidal, and current velocities; wave characteristics; geotechnical data relating to surface and subsurface characteristics; seasonal and diurnal variations; and the interaction among these conditions. Figure 1 presents a graphical representation of some metocean phenomena that can impact offshore energy systems. This document outlines the metocean observations currently available; those that are not available; and those that require additional temporal-spatial coverage, resolution, or processing for offshore energy in an effort to gather agreed-upon, needed observations.

A GLANCE AT OFFSHORE WIND TURBINE FOUNDATION STRUCTURES

Directory of Open Access Journals (Sweden)

Jianhua Zhang

2016-06-01

Full Text Available Energy poverty and climate change are crucial issues we face in our societies. Offshore wind energy has been a reliable solution to both of these problems - solving our growing energy problems while reducing CO2 emission. Innovative foundation design is one of the setbacks faced by this industry. Designing and constructing a cost effective offshore wind farm is greatly hampered by technical and infrastructural challenges, especially in foundation structures. This paper provides a detailed overview of issues related to this problem, with the aim of eliminating the frequent misunderstandings which can arise among engineers and investors working in the offshore wind energy sector. It begins by investigating the latest data and recommendations regarding the design and deployment of various kinds of offshore wind turbine (OWT foundations. It provides a framework which enables us to study the different OWT foundations, including prototypes and their limitations. Various structural failure modes are highlighted and corrosion measures are presented. Moreover, various removal methods of support structures are put forward. Finally, this paper presents the setbacks preventing the spread of offshore wind energy and the future works for offshore wind energy applications.

Inversion tectonics of the benue trough | Mamah | Global Journal of ...

African Journals Online (AJOL)

Spreading was, however, arrested by the rotation of the hot spot plumes onto the shoulders of the trough such as unto the Cameroom volcanic line by a sequence of events including crustal thinning and doming, rifting and faulting, grabens and horst formation, volcanism and subsidence, imbricate sedimentation and ...

Modular Trough Power Plant Cycle and Systems Analysis

Energy Technology Data Exchange (ETDEWEB)

Price, H.; Hassani, V.

2002-01-01

This report summarizes an analysis to reduce the cost of power production from modular concentrating solar power plants through a relatively new and exciting concept that merges two mature technologies to produce distributed modular electric power in the range of 500 to 1,500 kWe. These are the organic Rankine cycle (ORC) power plant and the concentrating solar parabolic (CSP) trough technologies that have been developed independent of each other over many years.

Wind Tunnel Tests of Parabolic Trough Solar Collectors: March 2001--August 2003

Energy Technology Data Exchange (ETDEWEB)

Hosoya, N.; Peterka, J. A.; Gee, R. C.; Kearney, D.

2008-05-01

Conducted extensive wind-tunnel tests on parabolic trough solar collectors to determine practical wind loads applicable to structural design for stress and deformation, and local component design for concentrator reflectors.

Are Vancomycin Trough Concentrations of 15 to 20 mg/L Associated With Increased Attainment of an AUC/MIC ≥ 400 in Patients With Presumed MRSA Infection?

Science.gov (United States)

Hale, Cory M; Seabury, Robert W; Steele, Jeffrey M; Darko, William; Miller, Christopher D

2017-06-01

To determine whether there is an association between higher vancomycin trough concentrations and attainment of a calculated area under the concentration-time curve (AUC)/minimum inhibitory concentration (MIC) ≥400. A retrospective analysis was conducted among vancomycin-treated adult patients with a positive methicillin-resistant Staphylococcus aureus (MRSA) culture. Attainment of a calculated AUC/MIC ≥400 was compared between patients with troughs in the reference range of 15 to 20 mg/L and those with troughs in the following ranges: 20 mg/L. Nephrotoxicity was assessed as a secondary outcome based on corrected average vancomycin troughs over 10 days of treatment. Overall, 226 patients were reviewed and 100 included. Relative to troughs ≥10, patients with vancomycin troughs AUC/MIC ≥400 (odds ratio [OR] 0.27, 95% confidence interval [CI]: 0.01-0.75). No difference was found in the attainment of an AUC/MIC ≥400 in patients with troughs of 10 to 14.9 mg/L and >20 mg/L when compared to patients with troughs of 15 to 20 mg/L. The mean corrected average vancomycin trough was higher in patients developing nephrotoxicity compared to those who did not (19.5 vs 14.5 mg/L, P AUC/MIC target relative to troughs of 10 to 14.9 mg/L but may increase nephrotoxicity risk.

Offshore Supply Industry Dynamics

DEFF Research Database (Denmark)

Roslyng Olesen, Thomas

The value chains for offshore oil and gas and offshore wind are both basically driven by the demand for energy. This is heavily dependent on a number of factors including the price of various energy sources and the policy making of the states which influence legislation, indirect subsidies...... of services including includes legal advice, financing, insurance etc. The two value chains have a number of activities in common. Both include (1) a tender and concession phase where the energy company obtains the right to explore and produce energy from the authorities. (2) An exploration phase where...

The Offshore New European Wind Atlas

Science.gov (United States)

Karagali, I.; Hahmann, A. N.; Badger, M.; Hasager, C.; Mann, J.

2017-12-01

The New European Wind Atlas (NEWA) is a joint effort of research agencies from eight European countries, co-funded under the ERANET Plus Program. The project is structured around two areas of work: development of dynamical downscaling methodologies and measurement campaigns to validate these methodologies, leading to the creation and publication of a European wind atlas in electronic form. This atlas will contain an offshore component extending 100 km from the European coasts. To achieve this, mesoscale models along with various observational datasets are utilised. Scanning lidars located at the coastline were used to compare the coastal wind gradient reproduced by the meso-scale model. Currently, an experimental campaign is occurring in the Baltic Sea, with a lidar located in a commercial ship sailing from Germany to Lithuania, thus covering the entire span of the south Baltic basin. In addition, satellite wind retrievals from scatterometers and Synthetic Aperture Radar (SAR) instruments were used to generate mean wind field maps and validate offshore modelled wind fields and identify the optimal model set-up parameters.The aim of this study is to compare the initial outputs from the offshore wind atlas produced by the Weather & Research Forecasting (WRF) model, still in pre-operational phase, and the METOP-A/B Advanced Scatterometer (ASCAT) wind fields, reprocessed to stress equivalent winds at 10m. Different experiments were set-up to evaluate the model sensitivity for the various domains covered by the NEWA offshore atlas. ASCAT winds were utilised to assess the performance of the WRF offshore atlases. In addition, ASCAT winds were used to create an offshore atlas covering the years 2007 to 2016, capturing the signature of various spatial wind features, such as channelling and lee effects from complex coastal topographical elements.

Economic optimization of offshore wind farms

International Nuclear Information System (INIS)

Pauling, T.

1996-09-01

The study on the title subject continues the development of a cost model for offshore wind farms started at the Institute for Wind Energy (IW) in 1995, and applies it on different kinds of cost analyses. The model will be considered within the European research project 'Structural and Economic Optimization of Bottom-Mounted Offshore Wind Energy Converters' (Opti-OWECS, JOR3-CT95-0087) co-ordinated by the IW, where also the cost analyses and optimization will be extended. The conclusions of the investigations have already been presented at the European Union Wind Energy Conference '96 at Goeteborg, Sweden. In Chapter 1, a short overview of former offshore studies and projects is given, especially those dealing with cost analysis. Typical cost breakdowns of offshore and onshore wind farms are compared. Chapter 2 contains a brief description of the cost model in its present state. The recent improvements and extensions are documented in Chapter 3, and a validation by means of a recalculation of two former offshore studies is carried out in Chapter 4. In Chapter 5, four different offshore sites are compared with respect to the same farm size and an optimized farm design: Jade in the German part of the North Sea near Wilhelmshafen; Swansea Bay in the Bristol Channel at the British Atlantic Coast; Rostock at the German Baltic Coast, and IJmuiden in the Dutch part of the North Sea. In Chapter 6, a sensitivity study is carried out for a variety of site, design and economical parameters. The results of this project are summarized in Chapter 7, and an outlook is given in Chapter 8. The appendix contains among others a description of the SCOptiM2 code, where the model is implemented, as well as data obtained from the parameter studies and design optimizations. 30 figs., 8 tabs., 6 appendices, 40 refs

Offshore production flares: a PETROBRAS review

Energy Technology Data Exchange (ETDEWEB)

Pagot, Paulo R.; Burmann, Clovis P.; Araujo, Paulo Bento de; Motomura, Tsukasa [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)

2008-07-01

The purpose of the present work is to briefly present the offshore flare system technological evolution and the main design criteria for flare and its supporting structure. In order to perform the aimed task, this work was divided into two parts: the first part presents the technological evolution of the offshore production flares and the second one discusses the flare system designing criteria. The evolution of the technology associated to the offshore production flares is organized by the authors just dividing the history in four chronological phases. Each phase is defined by the predominant use of the, by the time, most up-to-date technological alternative and it will be described with the help of sketches, drawings, photographs, data and information about the platforms where such technologies were applied. The second part of the present work discusses the dimensional criteria, interesting aspects and flaws of the offshore flare systems in two different fields, which are: definition of the flare system capacity; and flow and thermal design of the flare system. (author)

Development opportunities for the UK offshore wind industry

International Nuclear Information System (INIS)

1999-01-01

This report summarises the results of a study investigating the UK's ability to compete for the construction of offshore wind farms. The European offshore wind farm market is examined, and the UK offshore construction equipment and wind farm construction methods are analysed, and recommendations for a purpose build or modified construction vessel are presented. The appendix gives UK construction companies addresses and contact names

Tsunami Numerical Simulation for Hypothetical Giant or Great Earthquakes along the Izu-Bonin Trench

Science.gov (United States)

Harada, T.; Ishibashi, K.; Satake, K.

2013-12-01

We performed tsunami numerical simulations from various giant/great fault models along the Izu-Bonin trench in order to see the behavior of tsunamis originated in this region and to examine the recurrence pattern of great interplate earthquakes along the Nankai trough off southwest Japan. As a result, large tsunami heights are expected in the Ryukyu Islands and on the Pacific coasts of Kyushu, Shikoku and western Honshu. The computed large tsunami heights support the hypothesis that the 1605 Keicho Nankai earthquake was not a tsunami earthquake along the Nankai trough but a giant or great earthquake along the Izu-Bonin trench (Ishibashi and Harada, 2013, SSJ Fall Meeting abstract). The Izu-Bonin subduction zone has been regarded as so-called 'Mariana-type subduction zone' where M>7 interplate earthquakes do not occur inherently. However, since several M>7 outer-rise earthquakes have occurred in this region and the largest slip of the 2011 Tohoku earthquake (M9.0) took place on the shallow plate interface where the strain accumulation had considered to be a little, a possibility of M>8.5 earthquakes in this region may not be negligible. The latest M 7.4 outer-rise earthquake off the Bonin Islands on Dec. 22, 2010 produced small tsunamis on the Pacific coast of Japan except for the Tohoku and Hokkaido districts and a zone of abnormal seismic intensity in the Kanto and Tohoku districts. Ishibashi and Harada (2013) proposed a working hypothesis that the 1605 Keicho earthquake which is considered a great tsunami earthquake along the Nankai trough was a giant/great earthquake along the Izu-Bonin trench based on the similarity of the distributions of ground shaking and tsunami of this event and the 2010 Bonin earthquake. In this study, in order to examine the behavior of tsunamis from giant/great earthquakes along the Izu-Bonin trench and check the Ishibashi and Harada's hypothesis, we performed tsunami numerical simulations from fault models along the Izu-Bonin trench

PRA-1 offshore platform start-up within seven days; Operacionalizacao da plataforma offshore PRA-1 em sete dias

Energy Technology Data Exchange (ETDEWEB)

Barbosa, Fernando; Mitidieri, Jorge; Faria, Jose Luis Coutinho de; Ribeiro, Juan Carlos; Moura, Mario Arthur [Construtora Norberto Oderbrecht S.A., Rio de Janeiro, RJ (Brazil)

2008-07-01

The technologic innovations are very hard features with regards to Offshore Engineering and Construction over the worldwide. The innovations only make sense since they are focus on the high productivity, safe job and cost reduction compared with the current technologies. Inside the scenario mentioned above is Construtora Norberto Odebrecht S.A. concept for the PRA-1 platform Engineering and Construction. Through a very advanced and innovation concept, it was defined as the Main Strategic Planning of the undertaking not use a temporary platform support (named in Brazil as 'Flotel') during the 'Hook-up', commissioning and star-up offshore phase. The success of the strategic made possible through the implementation of new engineering tools, and, besides this, through a very careful offshore planning focused on minimizing and make easier as much as possible the offshore activities. The planning can be basically spitted on the following parts: A- Onshore preparations (Assembly, Integration and Commissioning of the Utilities and Accommodation Modules) B- Offshore detailed planning of the critical activities concerning the start-up of the systems responsible for leaving the platform ready for 'live'. This operation was defined as 'seven days of platform live support' (main target of this paper). (author)

Indian offshore wind energy policy - lessons from Europe

Energy Technology Data Exchange (ETDEWEB)

Mani, S.; Dhingra, T. [Univ. of Petroleum and Energy Studies (UPES), Dehradun (India)

2012-07-01

Indian Economy is growing at 8% for the past few years and is expected to continue this momentum into the foreseeable future. To sustain this growth, power sector needs to build additional generation capacity at an unprecedented pace. However, continued dependence on fossil fuels (especially Coal and Oil) to power the growth of electricity generation capacity, is hardly sustainable in the long run. The reasons are well known - Environmental concerns, depleting fossil fuel resources, excessive dependency on Oil imports - that it hardly merits repetition. Renewable Energy source forms a miniscule portion (25 GW, {approx} 12%) of India's overall Energy consumption today (202 GW). The share of wind energy (17 GW) is 67% of the total renewable energy basket. But the contribution from offshore wind farms is non-existent, as all the wind energy generated in India is only through onshore Wind farms. India needs a policy framework to encourage the development of offshore wind farms. Several European countries, most notably the UK, Germany and Denmark, have effective offshore wind energy policies that have helped them to accelerate the growth of their offshore wind energy sector. This paper does an exhaustive study to identify the building blocks of a successful offshore wind energy policy initiative adopted by selected European countries, which can be leveraged by India to articulate its own offshore wind energy policy. This paper also suggests a model to predict the log-odds of growth of offshore wind energy sector in India. (Author)

Prospects of the French offshore wind power market

International Nuclear Information System (INIS)

Anon.

2011-12-01

This market study about the French offshore wind power industry presents: 1 - the bases of the offshore wind power market: wind turbine operation principle, foundations and scale change; 2 - business model of offshore wind power projects: logistical, technical and financial challenges, cost structure and profitability of projects (investment, power generation costs, incentive mechanisms), project development time; 3 - European and French regulatory framework: the energy/climate package, the French 'Grenelle de l'Environnement' commitments for the development of renewable energies; 4 - start up of the French offshore wind power market: the onshore wind power market looking for growth relaying, the lateness of the offshore market, outlines of the call for bids and of the first phase launching (schedule, selected sites and candidates), market development stakes and opportunities; 5 - offshore wind power overview in Europe - lessons for the French market prospects: status of the European market (installed power/country, projects in progress), European leaders of the market (analysis of the British, Danish and German markets successful takeoff), specificities of the French market (are all favourable conditions present?); 6 - takeoff of the French market - what opportunities on the overall value chain?: front-end of the industry (manufacturers and component suppliers: industry structure, competition, R and D, subcontractors in France), back-end of the industry (developers/operators: sector analysis, ambitions, alliances, competences), specific French know-how in offshore installation and connection of wind turbines (reconversion of harbour areas, re-positioning of shipbuilding industry). (J.S.)

Operation and maintenance of offshore wind farms

DEFF Research Database (Denmark)

Petersen, Kristian R.; Madsen, Erik Skov; Bilberg, Arne

The offshore wind industry is booming and larger, more efficient wind-turbines have constantly been introduced into the market. However, research within the field of the operation and maintenance (O&M) of offshore wind farms is limited as the field is still immature. In this paper, two current ma...... maintenance models - RCM and TPM - are discussed in this context. Furthermore, through a case study, the paper looks into Modularization and SSLP, as these concepts can be utilized to optimize maintenance. This is a new approach for the offshore wind industry....

Reliability evaluation for offshore wind farms

DEFF Research Database (Denmark)

Zhao, Menghua; Blåbjerg, Frede; Chen, Zhe

2005-01-01

In this paper, a new reliability index - Loss Of Generation Ratio Probability (LOGRP) is proposed for evaluating the reliability of an electrical system for offshore wind farms, which emphasizes the design of wind farms rather than the adequacy for specific load demand. A practical method...... to calculate LOGRP of offshore wind farms is proposed and evaluated....

A fair wind for the offshore

International Nuclear Information System (INIS)

Houot, G.

2009-01-01

The wind power future will take into account the sea. But to increase, the offshore channel must manage its organization and create a real cross-border cooperation. The author presents an economic analysis of the market with a special attention to the french sector. A map of the offshore sites in Europe is provided. (A.L.B.)

Offshore northern Europe, the challenges

International Nuclear Information System (INIS)

Bergseth, S.

1996-01-01

This paper relates to challenges of the offshore activity in the North Sea. It is appropriate to address these challenges in the context of generating values through efficient management of resources, markets, safety and technology, as the challenges lie therein. The petroleum industry is built to turn natural resources into market value, assuring broad benefits to stake holders and shareholders. In the following, the challenges facing the industry the industry offshore Northern Europe is examined on this background

Offshore wind farm repowering optimization

DEFF Research Database (Denmark)

Hou, Peng; Enevoldsen, Peter; Hu, Weihao

2017-01-01

is focused on optimization of offshore wind farm repowering, which is one option for the wind farm owner at end of life for the offshore wind farm. The LCoE is used as the evaluation index to identify whether it is economical to invest in such a way. In an optimized repowering strategy, different types...... of wind turbines are selected to replace the original wind turbines to reconstruct the wind farm, which is demonstrated to be better than the refurbishment approach which replaces the old wind turbines with the same type. The simulations performed in this research reveal that the reconstructed wind farm......, which consists of multiple types of wind turbine, has a smaller LCoE (10.43%) than the refurbishment approach, which shows the superiority of the proposed method. This research contributes an optimization tool to the wind industry, which consequently drives down the cost of energy produced by offshore...

Getting the most from offshoring

DEFF Research Database (Denmark)

Wæhrens, Brian Vejrum; Slepniov, Dmitrij; Johansen, John

2014-01-01

Tapping into global resources is supposed to improve performance and contribute to a firm’s competitive advantage. However, a high offshoring quota may also lead to erosion of the firm’s home base capabilities and have wider negative implications for both the home base site position and the firm...... as a whole. The purpose of this paper is to conceptualize this scenario and propose how its adverse impacts can be addressed. From previous studies we know that the roles and mandates of home based sites of offshoring companies are changing from broad scoped manufacturing towards innovation and network...... orchestration. On the basis of the findings from the survey, series of workshops and case studies of Danish companies presented in this paper, we seek to determine the longer term effects of offshoring for home based sites. We conceptualize the findings in a framework and close with discussing the need...

Physical properties of the Nankai inner accretionary prism at Site C0002, IODP Expedition 348

Science.gov (United States)

Kitamura, Manami; Kitajima, Hiroko; Henry, Pierre; Valdez, Robert; Josh, Matthew

2014-05-01

Integrated Ocean Drilling Program (IODP) Nankai Trough Seismogenic Zone Experiment (NanTroSEIZE) Expedition 348 focused on deepening the existing riser hole at Site C0002 to ~3000 meters below seafloor (mbsf) to access the deep interior of the Miocene inner accretionary prism. This unique tectonic environment, which has never before been sampled in situ by ocean drilling, was characterized through riser drilling, logging while drilling (LWD), mud gas monitoring and sampling, and cuttings and core analysis. Shipboard physical properties measurements including moisture and density (MAD), electrical conductivity, P-wave, natural gamma ray, and magnetic susceptibility measurements were performed mainly on cuttings samples from 870.5 to 3058.5 mbsf, but also on core samples from 2163 and 2204 mbsf. MAD measurements were conducted on seawater-washed cuttings ("bulk cuttings") in two size fractions of >4 mm and 1-4 mm from 870.5 to 3058.5 mbsf, and hand-picked intact cuttings from the >4 mm size fractions within 1222.5-3058.5 mbsf interval. The bulk cuttings show grain density of 2.68 g/cm3 and 2.72 g/cm3, bulk density of 1.9 g/cm3 to 2.2 g/cm3, and porosity of 50% to 32%. Compared to the values on bulk cuttings, the intact cuttings show almost the same grain density (2.66-2.70 g/cm3), but higher bulk density (2.05-2.41 g/cm3) and lower porosity (37-18%), respectively. The grain density agreement suggests that the measurements on both bulk cuttings and intact cuttings are of good quality, and the differences in porosity and density are real, but the values from the bulk cuttings are affected strongly by artifacts of the drilling process. Thus, the bulk density and porosity data on handpicked cuttings are better representative of formation properties. Combined with the MAD measurements on hand-picked intact cuttings and discrete core samples from previous expeditions, porosity generally decreases from ~60% to ~20% from the seafloor to 3000 mbsf at Site C0002. Electrical

Offshore: Economic Deterrent or Necessity

Directory of Open Access Journals (Sweden)

Igor B. Turuev

2014-01-01

Full Text Available The downside of investment's addition rate in Russia, lack of capital investments result from "poor investment attractiveness". As a result, the companies' financial imbalance together with high investments risks lead to capital outflow from the country by virtue of offshores. Along with negative aspects connected with "financial oases" many advantages are given to the business community: lessening of tax payments, monetary privacy and confidentiality of operations. Taking in consideration the above and also the existence of specific international agreements concerning the avoidance of double taxation and offshore zones, the banner of the latter appears to be quite difficult and would divest the global economy of an important segment of global economic growth. The author performed a SWOT analysis of the role and the importance of offshores in international economy. Tolerant coexistence of local and global economic interests seems to be achievable by implementing a distinct circumspect and complex plan of measures aimed at the raise of the investment attractiveness of a country, for which the creation of "Skolkovo" and new Institutes for market development would not be sufficient. Transparent and oriented on business stability and safety provision of monitor and regulatory system, data interflow, improvement of prudential control on financial markets operations - are parts of measures that have to be accomplished in order to solve and exclude the problems associated with offshores. But the author also appeals to not forgetting that besides the offshores exists a number of such issues directly related to the outflow of capital as lowering of inflationary pace, enlargement of direct investment flow-in, support of social peace, which have to be handled for the purposes of improvement of domestic investment climate of countries with developing economy.

A Combined Optical, Thermal and Electrical Performance Study of a V-Trough PV System—Experimental and Analytical Investigations

Directory of Open Access Journals (Sweden)

Haitham M. Bahaidarah

2015-04-01

Full Text Available The objective of this study was to achieve higher efficiency of a PV system while reducing of the cost of energy generation. Concentration photovoltaics was employed in the present case as it uses low cost reflectors to enhance the efficiency of the PV system and simultaneously reduces the cost of electricity generation. For this purpose a V-trough integrated with the PV system was employed for low concentration photovoltaic (LCPV. Since the electrical output of the concentrating PV system is significantly affected by the temperature of the PV cells, the motivation of the research also included studying the ability to actively cool PV cells to achieve the maximum benefit. The optical, thermal and electrical performance of the V-trough PV system was theoretically modeled and validated with experimental results. Optical modeling of V-trough was carried out to estimate the amount of enhanced absorbed radiation. Due to increase in the absorbed radiation the module temperature was also increased which was predicted by thermal model. Active cooling techniques were studied and the effect of cooling was analyzed on the performance of V-trough PV system. With absorbed radiation and module temperature as input parameters, electrical modeling was carried out and the maximum power was estimated. For the V-trough PV system, experiments were performed for validating the numerical models and very good agreement was found between the two.

International activities and experience in offshore wind power generation; Internationale Aktivitaeten und Erfahrungen im Bereich der Offshore-Windenergienutzung

Energy Technology Data Exchange (ETDEWEB)

Rehfeldt, K.; Gerdes, G.J.

2002-01-01

Current activities in the area of offshore wind energy are being made only in the European Community in the form of concrete plans or as projects. Denmark and Sweden began as pioneers in the setting up of offshore wind parks along their coast in the Baltic Sea. As a world-wide first, Denmark saw the practicality of offshore wind energy as a way of reducing the emission of CO{sub 2} and opening new doors in the wind energy branch. Essential is not to name the ambitious goals, but that at the designated suitable regions, pilot projects are implemented therefore initiating extensive research and development projects. Our European neighbours have shown us through their own experience what great potential and underlying dynamic offshore wind energy has. The development of projects can be given with confidence to private sector, if however the main consensus from promoters and environmentalists is desired, then in this instance the governmental participation as a guide would be desirable. (orig.)

Cascade system using both trough system and dish system for power generation

International Nuclear Information System (INIS)

Zhang, Cheng; Zhang, Yanping; Arauzo, Inmaculada; Gao, Wei; Zou, Chongzhe

2017-01-01

Highlights: • A novel solar cascade system using both trough and dish collectors is proposed. • Heat rejected by the Stirling engines is collected by the condensed water. • The directions to increase the efficiency improvement has been pointed out • Influence of flow type of heating/cooling fluids of Stirling engines is considered. - Abstract: This paper represents a novel solar thermal cascade system using both trough and dish systems for power generation. An effective structure using the condensed fluid of Rankine cycle to cool the Stirling engines to use the heat released by Stirling engines was proposed. The cascade system model with different fluid circuits was developed. The models of some important components of the system, such as dish collector, trough collector and Stirling engine array, are presented with detail explanation in this paper. Corresponding stand-alone systems were also developed for comparison. Simulations were conducted with the models to find out efficiency difference between cascade system and corresponding stand-alone systems. The directions to increase the efficiency difference were also considered. Results show that the cascade system can achieve a higher efficiency with a high solar irradiance (>550 W/m"2). The flow type of fluids between heating and cooling Stirling engine array is also required to concern on designing a cascade system with Stirling engine array.

Practicality and Performance of Daylight Trough in The Tropics: A Case Study

Directory of Open Access Journals (Sweden)

Gene-Harn Lim

2016-01-01

Full Text Available The field of office daylighting is vital for both energy efficiency practice and occupants’ visual comfort. With the emergence of green building in Malaysia, building designers are exploring avenues for energy efficiency design; one common strategy is daylighting. The majority literature reviews on daylighting are skewed towards temperate or developed countries, where sky luminous condition is different from that of the Tropics. Conventional daylighting system designs redirect daylight from the envelope or atrium openings, such as light shelves. Presumed to be the pioneer daylight trough in the Tropics, this paper presents the simulated and in-situ lighting level measurements prior to occupancy. This case study presents an as-built daylight trough design which is able to daylight the office space as deep as 6 meters sufficiently. It achieves a lighting power density 1.90W/m2 and saves 39.2% of lighting energy over conventional office lighting energy. Discussed further is the practicality of working with such a system, including cost implication, return on investment and contractual challenges in reaching a consensus on the design. The results reinforce that the effectiveness of daylighting design is very dependable on the sun path and obstacles surrounding the office tower. The RADIANCE simulation correlates well to field measurement results. Further investigation into the light trough, its lighting energy savings, users’ interaction, visual comfort, and glare is still ongoing.

Overall Optimization for Offshore Wind Farm Electrical System

DEFF Research Database (Denmark)

Hou, Peng; Hu, Weihao; Chen, Cong

2017-01-01

Based on particle swarm optimization (PSO), an optimization platform for offshore wind farm electrical system (OWFES) is proposed in this paper, where the main components of an offshore wind farm and key technical constraints are considered as input parameters. The offshore wind farm electrical...... system is optimized in accordance with initial investment by considering three aspects: the number and siting of offshore substations (OS), the cable connection layout of both collection system (CS) and transmission system (TS) as well as the selection of electrical components in terms of voltage level...... that save 3.01% total cost compared with the industrial layout, and can be a useful tool for OWFES design and evaluation....

Legal aspects of financing Canadian offshore oil and gas developments

International Nuclear Information System (INIS)

Green, J.M.; Hudec, A.J.

1992-01-01

A review is presented of the significant legal considerations involved in structuring, negotiating, and documenting commercial financing of a Canadian offshore oil and gas production facility. Emphasis is placed on the Hibernia Project in the Newfoundland offshore as an example, and more specifically the $450 million bank financing completed in November 1991. The legal framework governing offshore production financing in this case was complex, due to the project's location in international waters on the continental shelf. Complex intergovernmental arrangements have been implemented between Canada and Newfoundland to govern the offshore area and regulate the project. An agreement called the Atlantic Accord allowed the Canada Newfoundland Offshore Petroleum Board (CNOPB) to grant production licenses and to regulate offshore exploration and development, with matters relating to legislation, taxation, and royalties shared between the governments. Certain other acts were enacted or extended for application to the offshore area. The CNOPB administers a registry system for transfers and security interests in offshore licenses. Security interests including property are ensured by the Hibernia Act, which makes Newfoundland's existing security interest regime applicable to the offshore. The project owners are operating Hibernia as a joint venture, and the structure of project financing and inter-creditor arrangements is examined. The competing security interest of project lenders and non-defaulting participants is discussed, along with assignment of priorities on the security in case of default

Exploring Unconventional Hydrocarbons in the Makó Trough, Pannonian basin, Hungary: Results and Challenges

Science.gov (United States)

Horvath, Anita; Bada, Gabor; Szafian, Peter; Sztano, Orsolya; Law, Ben; Wallis, Rod

2010-05-01

The latest phase exploration in the Makó Trough, which commenced a few years ago, has focused on the utilization of unconventional hydrocarbons. Accumulations are regarded as "unconventional" when they cannot be produced economically except by means of some sort of stimulation, usually hydraulic fracturing. The model we have developed for the evaluation of the hydrocarbon potential indicates a significant gas accumulation in the area of the Makó Trough. The tally of the distinctive attributes of the hydrocarbon system and the combined analysis of the available geological data led to the conclusion that the Makó Trough represents an area of active basin-centered gas accumulation (BCGA), with very significant perspective reserves. In a BCGA, hydrocarbons do not accumulate conventionally, in structural or stratigraphic traps, but rather in cells. Due to the geological setting of the Makó Trough, the hydrocarbon cell here forms a relatively continuous zone marked by considerable internal lithological and petrophysical variability. The most prolific parts, called sweet spots, possess a reservoir potential higher than the average. The identification of these sweet spots constitutes one of the most important, and quite possibly the most challenging task of the entire exploration project. The hemipelagic Endrőd Formation, which acts as the source rock, contains organic-rich marls in a depth delimited by the 170-230 °C isotherms. These marls constitute the still active hydrocarbon "kitchen" of the BCGA in the Makó Trough. The top and bottom boundaries of the cell essentially coincide with the turbidites of the Szolnok Formation and the top of the pre-Neogene basement, respectively. In light of the fact that pressure, temperature, and maturity tests have produced rather similar results in a number of wells in the area, we have reason to believe that the extension of the Makó Trough's BCGA is of regional dimensions (>1000 km2). The thickness and lateral extension of

46 CFR 111.105-33 - Mobile offshore drilling units.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Mobile offshore drilling units. 111.105-33 Section 111... ELECTRIC SYSTEMS-GENERAL REQUIREMENTS Hazardous Locations § 111.105-33 Mobile offshore drilling units. (a) Applicability. This section applies to each mobile offshore drilling unit. (b) Definitions. As used in this...

Whether or Not to Prepare for Offshoring

DEFF Research Database (Denmark)

Møller Larsen, Marcus; Geisler Asmussen, Christian; Pedersen, Torben

2012-01-01

A consequence of offshoring is increased coordination costs. To counter this, firms can strive to identify a cost reducing organizational configuration either ex ante or ex post to the offshoring implementation. In this paper, we investigate the performance implications of these contrasting strat...

Dynamic analysis and design of offshore structures

CERN Document Server

Chandrasekaran, Srinivasan

2015-01-01

This book  attempts to provide readers with an overall idea of various types of offshore platform geometries. It covers the various environmental loads encountered by these structures, a detailed description of the fundamentals of structural dynamics in a class-room style, estimate of damping in offshore structures and their applications in the preliminary analysis and design. Basic concepts of structural dynamics are emphasized through simple illustrative examples and exercises. Design methodologies and guidelines, which are FORM based concepts are explained through a few applied example structures. Each chapter also has tutorials and exercises for self-learning. A dedicated chapter on stochastic dynamics will help the students to extend the basic concepts of structural dynamics to this advanced domain of research. Hydrodynamic response of offshore structures with perforated members is one of the recent research applications, which is found to be one of the effective manner of retrofitting offshore structur...

Second wind in the offshore wind industry

International Nuclear Information System (INIS)

Philippe, Edouard; Neyme, Eric; Deboos, Christophe; Villageois, Jean-Remy; Gouverneur, Philippe; Gerard, Bernard; Fournier, Eric; Petrus, Raymond; Lemarquis, David; Dener, Marc; Bivaud, Jean-Pierre; Lemaire, Etienne; Nielsen, Steffen; Lafon, Xavier; Lagandre, Pierre; Nadai, Alain; Pinot de Villechenon, Edouard; Westhues, Markus; Herpers, Frederick; Bisiaux, Christophe; Sperlich, Miriam; Bales, Vincent; Vandenbroeck, Jan; His, Stephane; Derrey, Thierry; Barakat, Georges; Dakyo, Brayima; Carme, Laurent; Petit, Frederic; Ytournel, Sophie; Westhues, Markus; Diller, Armin; Premont, Antoine de; Ruer, Jacques; Lanoe, Frederic; Declercq, Jan; Holmager, Morten; Fidelin, Daniel; Guillet, Jerome; Dudziak, Gregory; Lapierre, Anne; Couturier, Ludovic; Audineau, Jean-Pierre; Rouaix, Eric; De Roeck, Yann-Herve; Quesnel, Louis; Duguet, Benjamin

2011-06-01

After several keynote addresses, this publication contains contributions and Power Point presentations proposed during this conference on the development of offshore wind energy. The successive sessions addressed the following issues: the offshore mass production of electricity (examples of Denmark and Belgium, laying and protecting offshore cables), the space, economic and environmental planning (the Danish experience, the role of the Coastal area integrated management, importance of the public debate, so on), the logistics of port infrastructures (simulation tools, example of Bremerhaven, issues related to project management), innovation at the core of industrial strategies (high power wind turbines, the 6 MW Alstom turbine, chain value and innovation in offshore wind energy, the Vertiwing innovating project of a floating wind turbine, a bench test in Charleston, foundations, gravity base structures, the British experience, the Danish experience), the economic and organisational conditions for development, the validation and certification of technologies

Simulation of the parabolic trough solar energy generation system with Organic Rankine Cycle

International Nuclear Information System (INIS)

He, Ya-Ling; Mei, Dan-Hua; Tao, Wen-Quan; Yang, Wei-Wei; Liu, Huai-Liang

2012-01-01

Highlights: ► A parabolic trough solar power generation system with ORC is numerically simulated. ► The effects of key parameters on collector field and system performance are studied. ► Collector heat loss increases with small absorber and glass tube interlayer pressure. ► Heat collecting efficiency increases with initial increase of absorber HTO flow rate. ► Recommended thermal storage system volumes are different in year four typical days. -- Abstract: A model for a typical parabolic trough solar thermal power generation system with Organic Rankine Cycle (PT-SEGS–ORC) was built within the transient energy simulation package TRNSYS, which is formed by integrating several submodels for the trough collector system, the single-tank thermal storage system, the auxiliary power system and the heat-electricity conversion system. With this model, the effects of several key parameters, including the interlayer pressure between the absorber tube and the glass tube (p inter ), the flow rate of high temperature oil in the absorber tube (v), solar radiation intensity (I dn ) and incidence angle (θ), on the performance of the parabolic trough collector field based on the meteorological data of Xi’an city were examined. The study shows that the heat loss of the solar collector (q loss ) increases sharply with the increase in p inter at beginning and then reaches to an approximately constant value. The variation of heat collecting efficiency (η hc ) with v is quite similar to the variation of q loss with p inter . However, I dn and θ exhibit opposite effect on η hc . In addition, it is found that the optimal volume of the thermal storage system is sensitively dependent on the solar radiation intensity. The optimal volumes are 100, 150, 50, and 0 m 3 for spring equinox, summer solstice, autumnal equinox and winter solstice, respectively.

Morphotectonics of the central Muertos thrust belt and Muertos Trough (northeastern Caribbean)

Science.gov (United States)

Granja, Bruna J.L.; ten Brink, Uri S.; Carbó-Gorosabel, Andrés; Muñoz-Martín, A.; Gomez, Ballesteros M.

2009-01-01

Multibeam bathymetry data acquired during the 2005 Spanish R/V Hesp??rides cruise and reprocessed multichannel seismic profiles provide the basis for the analysis of the morphology and deformation in the central Muertos Trough and Muertos thrust belt. The Muertos Trough is an elongated basin developed where the Venezuelan Basin crust is thrusted under the Muertos fold-and-thrust belt. Structural variations along the Muertos Trough are suggested to be a consequence of the overburden of the asymmetrical thrust belt and by the variable nature of the Venezuelan Basin crust along the margin. The insular slope can be divided into three east-west trending slope provinces with high lateral variability which correspond to different accretion stages: 1) The lower slope is composed of an active sequence of imbricate thrust slices and closed fold axes, which form short and narrow accretionary ridges and elongated slope basins; 2) The middle slope shows a less active imbricate structure resulting in lower superficial deformation and bigger slope basins; 3) The upper slope comprises the talus region and extended terraces burying an island arc basement and an inactive imbricate structure. The talus region is characterized by a dense drainage network that transports turbidite flows from the islands and their surrounding carbonate platform areas to the slope basins and sometimes to the trough. In the survey area the accommodation of the ongoing east-west differential motion between the Hispaniola and the Puerto Rico-Virgin Islands blocks takes place by means of diffuse deformation. The asymmetrical development of the thrust belt is not related to the geological conditions in the foreland, but rather may be caused by variations in the geometry and movement of the backstop. The map-view curves of the thrust belt and the symmetry of the recesses suggest a main north-south convergence along the Muertos margin. The western end of the Investigator Fault Zone comprises a broad band of

Isotopic Characteristics and Age Dating of the Pumice in Okinawa Trough

Institute of Scientific and Technical Information of China (English)

陈丽蓉; 翟世奎; 申顺喜

1994-01-01

The data on the isotope compositions of rubidium,strontium and oxygen in the pumice ofOkinawa Trough are reported for the first time.The ages of the pumice were successfully dated with themethod of U-series disequilibrium.Then,the material source,crystallization evolution of magma and activi-ty cycles of volcanos are explored.Isotopic data show that pumice magma was originally from the mantle,but had undergone a full crystal-lization differentiation and had been contaminated to a fair extent by crust-derived materials before the mag-ma was erupted out of the sea floor.According to the dating results available so far,the earliest volcaniceruption in Okinawa Trough occurred about 70,000 a ago and the latest eruption was about 10,000 a B.P.During this period,there were three volcanic eruption cycles which were respectively corresponding to themiddle Late Pleistocene,the late Late Pleistocene and the Early Holocene.

Terminology Guideline for Classifying Offshore Wind Energy Resources

Energy Technology Data Exchange (ETDEWEB)

Beiter, Philipp [National Renewable Energy Lab. (NREL), Golden, CO (United States); Musial, Walt [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2016-09-01

The purpose of this guideline is to establish a clear and consistent vocabulary for conveying offshore wind resource potential and to interpret this vocabulary in terms that are familiar to the oil and gas (O&G) industry. This involves clarifying and refining existing definitions of offshore wind energy resource classes. The terminology developed in this guideline represents one of several possible sets of vocabulary that may differ with respect to their purpose, data availability, and comprehensiveness. It was customized to correspond with established offshore wind practices and existing renewable energy industry terminology (e.g. DOE 2013, Brown et al. 2015) while conforming to established fossil resource classification as best as possible. The developers of the guideline recognize the fundamental differences that exist between fossil and renewable energy resources with respect to availability, accessibility, lifetime, and quality. Any quantitative comparison between fossil and renewable energy resources, including offshore wind, is therefore limited. For instance, O&G resources are finite and there may be significant uncertainty associated with the amount of the resource. In contrast, aboveground renewable resources, such as offshore wind, do not generally deplete over time but can vary significantly subhourly, daily, seasonally, and annually. The intent of this guideline is to make these differences transparent and develop an offshore wind resource classification that conforms to established fossil resource classifications where possible. This guideline also provides methods to quantitatively compare certain offshore wind energy resources to O&G resource classes for specific applications. Finally, this guideline identifies areas where analogies to established O&G terminology may be inappropriate or subject to misinterpretation.

Dermal fillers for the treatment of tear trough deformity: A review of anatomy, treatment techniques, and their outcomes

Directory of Open Access Journals (Sweden)

Jaishree Sharad

2012-01-01

Full Text Available Tear trough deformity is a major concern in a lot of individuals seeking periorbital rejuvenation. A prominent tear trough deformity is characterised by a sunken appearance of the eye that results in the casting of a dark shadow over the lower eyelid, giving the patient a fatigued appearance despite adequate rest, and is refractory to attempts at cosmetic concealment. The tear trough deformity is a natural consequence of the anatomic attachments of the periorbital tissues. A variety of techniques have evolved to address this cosmetic issue. Traditional techniques relied on surgical excision of skin, muscle, and fat as well as chemical peels. Treatment is now tailored towards specific anatomic abnormalities and often employs multiple modalities including surgery, botulinum toxin, and replacement of volume. Various original research articles, text book publications and review articles were studied. Data specific to the historical aspect and anatomy of tear trough have been enumerated. Techniques of different authors were analysed and their results and complications have been summarised. The technique of the author has also been described here.

Soil-Structure Interaction For Nonslender, Large-Diameter Offshore Monopiles

DEFF Research Database (Denmark)

Sørensen, Søren Peder Hyldal

Strong political and industrial forces, especially in Northern Europe, support the development of new technologies as well as improvements of existing technologies within the field of renewable energy. Offshore wind power is a domestic, sustainable and largely untapped energy resource. Today......, the modern offshore wind turbine offers competitive production prices compared to other sources of renewable energy. Therefore, it is a key technology in breaking the dependence on fossil fuels and in achieving the energy and climate goals of the future. For offshore wind turbines, the costs of foundation...... typically constitutes 20-30 % of the total costs. Hence, improved methods for the design of foundations for offshore wind turbines can increase the competitiveness of offshore wind energy significantly. The monopile foundation concept has been employed as the foundation for the majority of the currently...

Optimized power generation in offshore wind parks

NARCIS (Netherlands)

Oliveira Filho, J. de; Papp, Z.

2011-01-01

Electricity generation on offshore wind parks has an increasing economic importance - the European Commission foresees that 12% of the wind energy will be produced on offshore installations by 2020, and this share is likely to increase further in the following years. However, the continuously

Offshore wind market outlook in Northern Europe

Energy Technology Data Exchange (ETDEWEB)

Pimenta de Miranda, Wilfried; Trulsson, Ola; Ekloef, Eva-Britt; Niemenen, Karel

2010-08-15

After more than 10 years of slow developments, the offshore wind market is now accelerating. Thanks to a sustained political drive from UK and Germany, the rest of Northern Europe is now following the path as offshore wind is being recognized as one of the key resources available to the EU to meet its renewable energy ambitions. Exposed to increasing technical issues, rising costs and the financial crisis, lessons learned are now being shared and integrated throughout Europe and appropriate regulatory and planning reforms are now being deployed to speed the deployment of offshore wind. (Author)

Major hazards onshore and offshore

International Nuclear Information System (INIS)

1992-01-01

This symposium continues the tradition of bringing together papers on a topic of current interest and importance in terms of process safety - in this case, Major Hazards Onshore and Offshore. Lord Cullen in his report on the Piper Alpha disaster has, in effect, suggested that the experience gained in the control of major hazards onshore during the 1980s should be applied to improve safety offshore during the 1990s. This major three-day symposium reviews what has been learned so far with regard to major hazards and considers its present and future applications both onshore and offshore. The topics covered in the programme are wide ranging and deal with all aspects of legislation, the application of regulations, techniques for evaluating hazards and prescribing safety measures in design, construction and operation, the importance of the human factors, and recent technical developments in protective measures, relief venting and predicting the consequences of fires and explosions. (author)

A framework for offshore vendor capability development

Science.gov (United States)

Yusuf Wibisono, Yogi; Govindaraju, Rajesri; Irianto, Dradjad; Sudirman, Iman

2016-02-01

Offshore outsourcing is a common practice conducted by companies, especially in developed countries, by relocating one or more their business processes to other companies abroad, especially in developing countries. This practice grows rapidly owing to the ease of accessing qualified vendors with a lower cost. Vendors in developing countries compete more intensely to acquire offshore projects. Indonesia is still below India, China, Malaysia as main global offshore destinations. Vendor capability is among other factors that contribute to the inability of Indonesian vendor in competing with other companies in the global market. Therefore, it is essential to study how to increase the vendor's capability in Indonesia, in the context of global offshore outsourcing. Previous studies on the vendor's capability mainly focus on capabilities without considering the dynamic of capabilities due to the environmental changes. In order to be able to compete with competitors and maintain the competitive advantage, it is necessary for vendors to develop their capabilities continuously. The purpose of this study is to develop a framework that describes offshore vendor capability development along the client-vendor relationship stages. The framework consists of three main components, i.e. the stages of client-vendor relationship, the success of each stage, and the capabilities of vendor at each stage.

ISM Approach to Model Offshore Outsourcing Risks

Directory of Open Access Journals (Sweden)

Sunand Kumar

2014-07-01

Full Text Available In an effort to achieve a competitive advantage via cost reductions and improved market responsiveness, organizations are increasingly employing offshore outsourcing as a major component of their supply chain strategies. But as evident from literature number of risks such as Political risk, Risk due to cultural differences, Compliance and regulatory risk, Opportunistic risk and Organization structural risk, which adversely affect the performance of offshore outsourcing in a supply chain network. This also leads to dissatisfaction among different stake holders. The main objective of this paper is to identify and understand the mutual interaction among various risks which affect the performance of offshore outsourcing.  To this effect, authors have identified various risks through extant review of literature.  From this information, an integrated model using interpretive structural modelling (ISM for risks affecting offshore outsourcing is developed and the structural relationships between these risks are modeled.  Further, MICMAC analysis is done to analyze the driving power and dependency of risks which shall be helpful to managers to identify and classify important criterions and to reveal the direct and indirect effects of each criterion on offshore outsourcing. Results show that political risk and risk due to cultural differences are act as strong drivers.

Geochemistry of trace elements and Sr- Nd isotopes of foraminifera shell from the Okinawa Trough

Institute of Scientific and Technical Information of China (English)

无

2001-01-01

Trace elemental associations and Sr - Nd isotopic compositions are of important to recognition of biogenic material from mixed marine sediments. The foraminifera shell from the Okinawa Trough strongly enrichesSr, P, Mn andBa, enriches Li, U, Th, Sc, Co, Cu, Pb, Zn, Cr, Rb, Y, Sb and light rare earth elements, slightly enriches V, Ga, Zr, Nb, Cd and middle rare earth elements,is short of Mo, In, Sn, Cs, Hf, Ta, W, Ti, Bi and heavy rare earth elements. The mechanism of elemental enrichment in forminifera is the concentrations of trace elements in sea water and selective absorption of trace elements during foraminifera living, as well as the geochemical affinity between major elements and trace elements. The REE (rare earth elements) partition pattern of foraminifera shell of the Okinawa Trough shows enrichment of middle rare earth elements with slightly negative Ce anomaly,which are different from those of foraminifera of the Pacific Ocean. The Sr, Nd isotopic ratios of the Okinawa Trough foraminifera are 0.709 769 and 0.512 162, respectively, which are different not only from those of oceanic water, but also from those of river water of China's Mainland, the former is slightly higher than those of oceanic water, but much lower than those of river water; the latter is slightly lower than those of oceanic water, but higher than those of river water, demonstrating that the Okinawa Trough sea water has been influenced by river water of China's Mainland.

Governance Models of R&D Offshoring: : Innovatoin Performance and Absorptive Capacity

NARCIS (Netherlands)

Steinberg, Philip; Procher, Vivien D.

2015-01-01

The globalization of business functions has led to an increase in offshoring of R&D. Firms’ offshoring models of R&D include captive offshoring (foreign R&D spending to affiliates) and offshore outsourcing (foreign R&D spending to external partners). For 2,421 R&D-active German enterprises we

Solar power satellite offshore rectenna study

Science.gov (United States)

1980-01-01

It was found that an offshore rectenna is feasible and cost competitive with land rectennas but that the type of rectenna which is suitable for offshore use is quite different from that specified in the present reference system. The result is a nonground plane design which minimizes the weight and greatly reduces the number of costly support towers. This preferred design is an antenna array consisting of individually encapsulated dipoles with reflectors supported on feed wires. Such a 5 GW rectenna could be built at a 50 m water depth site to withstand hurricane and icing conditions for a one time cost of 5.7 billion dollars. Subsequent units would be about 1/3 less expensive. The east coast site chosen for this study represents an extreme case of severe environmental conditions. More benign and more shallow water sites would result in lower costs. Secondary uses such as mariculture appear practical with only minor impact on the rectenna design. The potential advantages of an offshore rectenna, such as no land requirements, removal of microwave radiation from populated areas and minimal impact on the local geopolitics argue strongly that further investigation of the offshore rectenna should be vigorously pursued.

On purpose simulation model for molten salt CSP parabolic trough

Science.gov (United States)

Caranese, Carlo; Matino, Francesca; Maccari, Augusto

2017-06-01

The utilization of computer codes and simulation software is one of the fundamental aspects for the development of any kind of technology and, in particular, in CSP sector for researchers, energy institutions, EPC and others stakeholders. In that extent, several models for the simulation of CSP plant have been developed with different main objectives (dynamic simulation, productivity analysis, techno economic optimization, etc.), each of which has shown its own validity and suitability. Some of those models have been designed to study several plant configurations taking into account different CSP plant technologies (Parabolic trough, Linear Fresnel, Solar Tower or Dish) and different settings for the heat transfer fluid, the thermal storage systems and for the overall plant operating logic. Due to a lack of direct experience of Molten Salt Parabolic Trough (MSPT) commercial plant operation, most of the simulation tools do not foresee a suitable management of the thermal energy storage logic and of the solar field freeze protection system, but follow standard schemes. ASSALT, Ase Software for SALT csp plants, has been developed to improve MSPT plant's simulations, by exploiting the most correct operational strategies in order to provide more accurate technical and economical results. In particular, ASSALT applies MSPT specific control logics for the electric energy production and delivery strategy as well as the operation modes of the Solar Field in off-normal sunshine condition. With this approach, the estimated plant efficiency is increased and the electricity consumptions required for the plant operation and management is drastically reduced. Here we present a first comparative study on a real case 55 MWe Molten Salt Parabolic Trough CSP plant placed in the Tibetan highlands, using ASSALT and SAM (System Advisor Model), which is a commercially available simulation tool.

Numerical simulation of solar parabolic trough collector performance in the Algeria Saharan region

International Nuclear Information System (INIS)

Marif, Yacine; Benmoussa, Hocine; Bouguettaia, Hamza; Belhadj, Mohamed M.; Zerrouki, Moussa

2014-01-01

Highlights: • The parabolic trough collector performance is examined. • The finite difference method is proposed and validated. • Two fluids are considered water and TherminolVP-1™. - Abstract: In order to determine the optical and thermal performance of a solar parabolic trough collector under the climate conditions of Algerian Sahara, a computer program based on one dimensional implicit finite difference method with energy balance approach has been developed. The absorber pipe, glass envelope and fluid were divided into several segments and the partial derivation in the differential equations was replaced by the backward finite difference terms in each segment. Two fluids were considered, liquid water and TherminolVP-1™ synthetic oil. Furthermore, the intensity of the direct solar radiation was estimated by monthly average values of the atmospheric Linke turbidity factor for different tracking systems. According to the simulation findings, the one axis polar East–West and horizontal East–West tracking systems were most desirable for a parabolic trough collector throughout the whole year. In addition, it is found that the thermal efficiency was about 69.73–72.24%, which decreases with the high synthetic oil fluid temperatures and increases in the lower water temperature by 2%

The crustal structure along the Mbere trough in South Adamawa ...

African Journals Online (AJOL)

The Mbere Cretaceous trough is located in the southern part of the Adamawa province. A gravity interpretation based on data obtained from three NW-SE profiles on the residual anomaly map has been carried out using a 2.5D modelling program. Spectral analysis has been used to estimate the depth of geological ...

Overland conveyors. Cable or trough belt for 100 km transport haulage

Energy Technology Data Exchange (ETDEWEB)

Maton, A.E. [Maton Engineering Pty. Ltd., Orange Grove, WA (Australia)

2009-07-01

With the advances in belt conveyor technology today systems of 100 kilometres length are increasingly being considered. This article provides a comparison of two concepts for a 100 kilometre system of five 20 kilometre flights based on trough belt and cable belt technology. (orig.)

Modern earthquake engineering offshore and land-based structures

CERN Document Server

Jia, Junbo

2017-01-01

This book addresses applications of earthquake engineering for both offshore and land-based structures. It is self-contained as a reference work and covers a wide range of topics, including topics related to engineering seismology, geotechnical earthquake engineering, structural engineering, as well as special contents dedicated to design philosophy, determination of ground motions, shock waves, tsunamis, earthquake damage, seismic response of offshore and arctic structures, spatial varied ground motions, simplified and advanced seismic analysis methods, sudden subsidence of offshore platforms, tank liquid impacts during earthquakes, seismic resistance of non-structural elements, and various types of mitigation measures, etc. The target readership includes professionals in offshore and civil engineering, officials and regulators, as well as researchers and students in this field.

Site selection for offshore wind farms along the Indian coast

Digital Repository Service at National Institute of Oceanography (India)

ManiMurali, R.; Vidya, P.J.; Modi, P.; JayaKumar, S.

This study deals with locating the potential sites for offshore wind farms and also deals with feasibility of installing offshore wind farms through scientific examination of the requirements along the coast of India Offshore wind energy is almost...

Offshoring in the Semiconductor Industry: A Historical Perspective

OpenAIRE

Brown, Clair; Linden, Greg

2005-01-01

Semiconductor design is a frequently-cited example of the new wave of offshoring and foreign-outsourcing of service sector jobs. It is certainly a concern to U.S. design engineers themselves. In addition to the current wave of white-collar outsourcing, the industry also has a rich experience with offshoring of manufacturing activity. Semiconductor companies were among the first to invest in offshore facilities to manufacture goods for imports back to the U.S. A brief review of these...

Gaining Flexibility and Innovation through Offshore Outsourcing

Directory of Open Access Journals (Sweden)

Michela Pellicelli

2018-05-01

Full Text Available Recently, offshore outsourcing has become extremely important for companies that compete worldwide. In many industries, only companies that manage to be competitive globally can aspire to attain sustainable competitive advantages. Therefore, offshore outsourcing has become essential for many companies and recently has become more and more a vital part of the long-term strategies of the leading firms. The rapidly shifting conditions in the marketplace is forcing management to constantly review and defend its core competencies. Management is now confronted with a higher level of complexity and disruptions brought about in particular by the new waves of globalization and the irresistible march of technological changes. For these reasons, offshore outsourcing is transforming the functions of the traditional firms into a network of competencies. The tendency to offshore most of the productive and economic activities and processes can lead companies to transform themselves into virtual organizations, where all the functions could be outsourced through the formation of flexible networks and agile organizational structures.

Co-sourcing in software development offshoring

DEFF Research Database (Denmark)

Schlichter, Bjarne Rerup; Persson, John Stouby

2013-01-01

Software development projects are increasingly geographical distributed with offshoring, which introduce complex risks that can lead to project failure. Co-sourcing is a highly integrative and cohesive approach, seen successful, to software development offshoring. However, research of how co-sour......-taking by high attention to of the closely interrelated structure and technology components in terms of CMMI and the actors’ cohesion and integration in terms of Scrum....

Emergency response in the Newfoundland offshore industry

Energy Technology Data Exchange (ETDEWEB)

Dempsey, J. [Cormorant Ltd., St. John' s, NL (Canada)

2006-07-01

This presentation reviewed current offshore oil activities with respect to safety issues regarding year-round marine operations in a harsh environment. Considerable logistics support is required for all offshore activities, including seismic and geotechnical surveys; exploration and production drilling; well testing; subsea construction; on-site production; and, delivery to market. Response to an offshore emergency must address the urgency of the incident along with stakeholder concerns. This presentation described the different types of emergencies and addressed issues regarding contingency planning; preventative measures; response philosophy; response scope; response at site; emergency management; communications links; and, oil spill response. The following current operations were highlighted: ExxonMobil's production drilling from the gravity-based concrete platform at Hibernia; Petro-Canada's production drilling at the Terra Nova FPSO; Husky Energy's production drilling at White Rose; and Chevron Canada's exploration drilling at the Orphan Basin. It was noted that in an emergency situation, the focus is on the welfare of offshore personnel. On an average day, the total offshore population is in the order of 1000 workers, all registered in the Personnel Logistics System which is updated with the departure of every helicopter from St. John's, Newfoundland or from the offshore platform. It is possible to prepare for foreseeable emergency incidents such as fire, explosion or gas leaks; spills to the marine environment; structural damage or collisions; persons lost at sea; helicopter or support vessel accidents; vessel sinking; sabotage; serious injuries or loss of life; severe ice events; and, loss of well control. The establishment of permanent safety zones at the Hibernia, White Rose and Terra Nova production fields are among the preventative measures, along with standby vessels that provide a rescue service for offshore installations

Emergency response in the Newfoundland offshore industry

International Nuclear Information System (INIS)

Dempsey, J.

2006-01-01

This presentation reviewed current offshore oil activities with respect to safety issues regarding year-round marine operations in a harsh environment. Considerable logistics support is required for all offshore activities, including seismic and geotechnical surveys; exploration and production drilling; well testing; subsea construction; on-site production; and, delivery to market. Response to an offshore emergency must address the urgency of the incident along with stakeholder concerns. This presentation described the different types of emergencies and addressed issues regarding contingency planning; preventative measures; response philosophy; response scope; response at site; emergency management; communications links; and, oil spill response. The following current operations were highlighted: ExxonMobil's production drilling from the gravity-based concrete platform at Hibernia; Petro-Canada's production drilling at the Terra Nova FPSO; Husky Energy's production drilling at White Rose; and Chevron Canada's exploration drilling at the Orphan Basin. It was noted that in an emergency situation, the focus is on the welfare of offshore personnel. On an average day, the total offshore population is in the order of 1000 workers, all registered in the Personnel Logistics System which is updated with the departure of every helicopter from St. John's, Newfoundland or from the offshore platform. It is possible to prepare for foreseeable emergency incidents such as fire, explosion or gas leaks; spills to the marine environment; structural damage or collisions; persons lost at sea; helicopter or support vessel accidents; vessel sinking; sabotage; serious injuries or loss of life; severe ice events; and, loss of well control. The establishment of permanent safety zones at the Hibernia, White Rose and Terra Nova production fields are among the preventative measures, along with standby vessels that provide a rescue service for offshore installations. Supply vessels are also

Offshore wind farm Bockstigen - installation and operation experience

Energy Technology Data Exchange (ETDEWEB)

Lange, B [Risoe National Lab., Wind Energy and Atmospheric Physics Dept., Roskilde (Denmark); Aagaard, E; Andersen, P E; Moeller, A [Wind World af 1997 A/S, Noerresundby (Denmark); Niklasson, S; Wickman, A [Vindkompaniet, Degerhamn (Sweden)

1999-03-01

The first Swedish offshore wind farm Bockstigen is operating since March 1998 near the coast of Gotland. It was built as a demonstration project by the Swedish wind farm developer Vindkompaniet, the Danish wind turbine manufacturer Wind World and the British offshore construction company Seacore and partly funded under the EU-THERMIE program. Bockstigen is the fourth offshore wind farm world-wide. While at previous wind farms the main emphasis laid on the demonstration of the technical feasibility of offshore wind energy utilisation, Bockstigen was aimed at demonstrating its economic viability. A number of innovative concepts have been employed: Drilled monopile foundations were used to save costs. A new construction method has been applied making use of a jack-up barge. A new control system for the turbines and the whole wind farm was developed, which controls the maximum power output, the flicker and the reactive power consumption depending on online measurements of the actual grid state. These new developments have been implemented successfully. A substantial cost reduction compared to previous offshore projects could be achieved. (au)

Alignment method for parabolic trough solar concentrators

Science.gov (United States)

Diver, Richard B [Albuquerque, NM

2010-02-23

A Theoretical Overlay Photographic (TOP) alignment method uses the overlay of a theoretical projected image of a perfectly aligned concentrator on a photographic image of the concentrator to align the mirror facets of a parabolic trough solar concentrator. The alignment method is practical and straightforward, and inherently aligns the mirror facets to the receiver. When integrated with clinometer measurements for which gravity and mechanical drag effects have been accounted for and which are made in a manner and location consistent with the alignment method, all of the mirrors on a common drive can be aligned and optimized for any concentrator orientation.

The offshoring challenge strategic design and innovation for tomorrow’s organization

CERN Document Server

Bals, Lydia; Jensen, Peter; Larsen, Marcus

2013-01-01

The continuous search for efficiency gains and the goal of attaining a sustainable competitive advantage have steadily increased the volume of goods and services procured globally from third party vendors. In this context, named as “the next wave of globalization”, the offshoring phenomenon has stimulated research and political debates. With the rise of services offshoring, international value chain disaggregation for services has reached a formerly unknown scale. Also, it is increasingly complex transactions, requiring a higher degree of qualification, which are becoming subject to offshoring as well. The Offshoring Challenge: Strategic Design and Innovation for Tomorrow’s Organization features selected chapters by an international research community on the topic of offshoring. All potential business models from offshore outsourcing to third party providers are covered, from cooperative arrangements to internal organizational set-ups including captive offshore centers. Contributions have significant in...

2014-2015 Offshore Wind Technologies Market Report

Energy Technology Data Exchange (ETDEWEB)

Smith, Aaron

2015-11-18

This presentation provides an overview of progress toward offshore wind cost reduction in Europe and implications for the U.S. market. The presentation covers an overview of offshore wind developments, economic and performance trends, empirical evidence of LCOE reduction, and challenges and opportunities in the U.S. market.

Offshore wind energy potential in China

DEFF Research Database (Denmark)

Hong, Lixuan; Möller, Bernd

2011-01-01

and economic costs. However, the influence of tropical cyclone risks on these regions and detailed assessments at regional or local scale are worth of further discussions. Nevertheless, the models and results provide a foundation for a more comprehensive regional planning framework that would address......This paper investigates available offshore wind energy resources in China’s exclusive economic zone (EEZ) with the aid of a Geographical Information System (GIS), which allows the influence of technical, spatial and economic constraints on offshore wind resources being reflected in a continuous...... space. Geospatial supply curves and spatial distribution of levelised production cost (LPC) are developed, which provide information on the available potential of offshore wind energy at or below a given cost, and its corresponding geographical locations. The GIS-based models also reflect the impacts...

RBI Optimization of Offshore Wind Turbines

DEFF Research Database (Denmark)

Ramírez, José G. Rangel; Sørensen, John Dalsgaard

2009-01-01

methods for oil & gas installations, a framework for optimal inspection and maintenance planning of offshore wind turbines is presented. Special aspects for offshore wind turbines considered are the fatigue loading characteristics where usually the wind loading are dominating the wave loading, wake......Wind turbines for electricity production have increased significantly the last years both in production capability and size. This development is expected to continue also in the coming years. Offshore wind turbines with an electricity production of 5-10 MW are planned. Typically, the wind turbine...... support structure is a steel structure consisting of a tower and a monopile, tripod or jacket type foundation. This paper considers aspects of inspection and maintenance planning of fatigue prone details in jacket and tripod type of wind turbine support structures. Based on risk-based inspection planning...

Offshore Wind Power at Rough Sea

DEFF Research Database (Denmark)

Petersen, Kristian Rasmus; Madsen, Erik Skov; Bilberg, Arne

2013-01-01

This study compare the current operations and maintenance issues of one offshore wind park at very rough sea conditions and two onshore wind parks. Through a detailed data analysis and case studies this study identifies how improvements have been made in maintenance of large wind turbines. Howeve......, the study has also revealed the need for new maintenance models including a shift from breakdown and preventive maintenances and towards more predictive maintenance to reduce the cost of energy for offshore wind energy installations in the future.......This study compare the current operations and maintenance issues of one offshore wind park at very rough sea conditions and two onshore wind parks. Through a detailed data analysis and case studies this study identifies how improvements have been made in maintenance of large wind turbines. However...

Project alliancing in the offshore industry

International Nuclear Information System (INIS)

Halman, J.I.M.; Braks, B.F.M.

1999-01-01

In this paper the shift towards new types of project organisation within the offshore industry is explained and discussed. Special focus is given to the organisational concept of project alliancing. The principles, structure and culture of a project alliance as applied within the offshore industry are described. In the paper the organisational concept of project alliancing is discussed on its potential to reduce project costs and enhance profits, both for the operator (oil and gas company) as well as for participating contractors. A risk and reward mechanism developed to share project risks and rewards between allied parties is explained for an alliance case. Based upon an in-depth study carried out within a contractor company in the offshore industry the organisational and financial implications of project alliancing are presented. (author)

Medical status of the offshore population

Energy Technology Data Exchange (ETDEWEB)

Coleshaw, S.R.K.; Harris, R.A.

1998-06-01

The offshore workforce are generally considered to be a healthy occupational group due to regular medical screening, a degree of health surveillance, self-selection, and an increasing number of health promotion programmes being run both onshore and offshore. That said, factors such as the increasing age of the workforce, the often poor lifestyle and the sometimes difficult psychosocial environment remain areas of concern when considering the physical and mental well-being of the workforce. The medical status of offshore workers was investigated by surveying the information collected during the medical screening process, over a cross-section of the population assessed by an independent health service provider. Demographic information, medical history and the results of medical examination were entered into a relational database, to allow analysis and interrogation of the data. (UK)

Quantifying the hurricane catastrophe risk to offshore wind power.

Science.gov (United States)

Rose, Stephen; Jaramillo, Paulina; Small, Mitchell J; Apt, Jay

2013-12-01

The U.S. Department of Energy has estimated that over 50 GW of offshore wind power will be required for the United States to generate 20% of its electricity from wind. Developers are actively planning offshore wind farms along the U.S. Atlantic and Gulf coasts and several leases have been signed for offshore sites. These planned projects are in areas that are sometimes struck by hurricanes. We present a method to estimate the catastrophe risk to offshore wind power using simulated hurricanes. Using this method, we estimate the fraction of offshore wind power simultaneously offline and the cumulative damage in a region. In Texas, the most vulnerable region we studied, 10% of offshore wind power could be offline simultaneously because of hurricane damage with a 100-year return period and 6% could be destroyed in any 10-year period. We also estimate the risks to single wind farms in four representative locations; we find the risks are significant but lower than those estimated in previously published results. Much of the hurricane risk to offshore wind turbines can be mitigated by designing turbines for higher maximum wind speeds, ensuring that turbine nacelles can turn quickly to track the wind direction even when grid power is lost, and building in areas with lower risk. © 2013 Society for Risk Analysis.

Mercury Anomaly in the Okinawa Trough Sediments—An Indicator of Modern Seafloor Hydrothermal Activity

Institute of Scientific and Technical Information of China (English)

赵一阳; 鄢明才

1995-01-01

The Okinawa Trough is located between the shelf-sea area of the East China Sea and the deep-sea area of western Pacific Ocean.More than 60 chemical elements in the sediments from the shelf area of the East China Sea,the Okinawa Trough and western Pacific Ocean were determined by advanced techniques including neutron acti-vation analysis,X-ray fluorescence spectrometry,atomic fluorescence spectrometry and atomic absorption spectrometry.Quantitative comparisons of the element abundances of the sediments were made in terms of the enrichment coefficients(K) of the elements.K>1.5 indicates enrichment (K=1.5-2, weak enrichment;K=2-4,strong enrichment) and K>4,anomalous enrichment.The results show that the Okinawa Trough sediments are characterized by Hg anomaly and the enrichment of such elements as Au,Ag,Se,Te,Sb,Cd,Mn,Mo,etc.Detailed studies show that the excess Hg comes from hydrothermal solutions rather than from the continent,sea water ,marine organisms,cosmic dust or vol-canic rocks.Attributed to modern hydrothermal activities on the sea floor ,Hg anomaly can be used as a geochemical indicator of modern seafloor hydrothermal activity.

MONTI as continent catheterized stoma using serosal-lined trough "Ghoneim Abolenin" technique in ileocystoplasty

Directory of Open Access Journals (Sweden)

Mohammed T Sammour

2011-01-01

Full Text Available It is a great challenge to select and perform continent mechanism in a stoma for urinary reservoir. A new technique by combining MONTI ileal conduit with the serosal lined trough in order to achieve continent catheterizable stoma to the umbilicus as a part of augmentation ileocystoplasty. We applied serosal-lined trough as a continent mechanism with MONTI ileal tube in 12 years smart girl underwent ileocystoplasty for neuropathic bladder due to meylomeningocele in whom continence failed to be achieved by using Mitrofanoff with submucosal tunnel of the bladder as continent mechanism before, also the previous operation included left to right transuretero-ureterostomy, ureterocystoplasty and reimplantation of the right ureter. The patient became completely continent; she was able to do self-catheterization easily through the umbilical stoma using 16-French catheter and was able to wash the mucous easily. The capacity of the augmented bladder was 300ccs. She became independent from her mother and stopped using diapers, anticholinergic and antibiotics. Combining MONTI conduit with serosal-lined extramural valve trough (The Ghoneim technique is an effective continent technique and gives wider channel for catheterization and washing out the mucous.

The cost of integration of parabolic trough CSP plants in isolated Mediterranean power systems

International Nuclear Information System (INIS)

Poullikkas, Andreas; Hadjipaschalis, Ioannis; Kourtis, George

2010-01-01

In this work, a technical and economic analysis concerning the integration of parabolic trough concentrated solar power (CSP) technologies, with or without thermal storage capability, in an existing typical small isolated Mediterranean power generation system, in the absence of a feed-in tariff scheme, is carried out. In addition to the business as usual (BAU) scenario, five more scenarios are examined in the analysis in order to assess the electricity unit cost with the penetration of parabolic trough CSP plants of 50 MWe or 100 MWe, with or without thermal storage capability. Based on the input data and assumptions made, the simulations indicated that the scenario with the utilization of a single parabolic trough CSP plant (either 50 MWe or 100 MWe and with or without thermal storage capability) in combination with BAU will effect an insignificant change in the electricity unit cost of the generation system compared to the BAU scenario. In addition, a sensitivity analysis on natural gas price, showed that increasing fuel prices and the existence of thermal storage capability in the CSP plant make this scenario marginally more economically attractive compared to the BAU scenario. (author)

Altitude variation of the plasmapause signature in the main ionospheric trough

Czech Academy of Sciences Publication Activity Database

Grebowsky, J. M.; Benson, R. F.; Webb, P. A.; Truhlík, Vladimír; Bilitza, D.

2009-01-01

Roč. 71, č. 16 (2009), s. 1669-1676 ISSN 1364-6826 R&D Projects: GA AV ČR IAA300420603 Institutional research plan: CEZ:AV0Z30420517 Keywords : Plasmapause * Ionosphere * Midlatitude Trough Subject RIV: DG - Athmosphere Sciences, Meteorology Impact factor: 1.643, year: 2009

Basinal Structure Of Yola Arm Of The Upper Benue Trough Nigeria ...

African Journals Online (AJOL)

Aeromagnetic data interpretation of the Yola arm of the Upper Benue Trough has previously been carried out. However, no detail modeling of the Crustal Structures has been undertaken. Two composite reduced Aeromagnetic maps on a scale of 1:250,000 were digitized and processed using computer techniques.

Critical success factors for offshoring of enterprise resource planning (ERP implementations

Directory of Open Access Journals (Sweden)

Rajneesh Chauhan

2012-01-01

Full Text Available Background: In recent years, offshoring enterprise resource planning (ERP implementation has been an emerging trend in the field of offshoring information technology (IT. However, both ERP implementations and IT offshoring are fraught with risks, and when both ERP implementation and IT offshoring happen together, the risks become even more pronounced. Therefore, it is important to understand and identify the issues of ERP implementation in an offshoring situation. Objectives: The purpose of this paper is to highlight the key factors that enable successful offshoring ERP implementation from the client and the vendor perspective. Methods/Approach: The paper uses literature as a basis for identifying a critical success factor, data collected through semi-structured interviews with ERP managers at various levels of the subject organizations, and eventually their analysis. Results: The findings of the paper reveal that various factors are critical while implementing offshoring ERP. They include: offshoring partnership, project management, project team composition, people issues, communications and compliance of the onsite team composition. It is also noticed that ten factors are grouped into three categories: the client side, the vendor side, and both. Conclusions: Organizations are currently undertaking or considering the offshoring ERP implementation particularly from India. This paper will enable them to understand the possible challenges and areas of offshoring the ERP implementation program. The value and originality of the paper comes from the fact that up to now, ERP implementation in offshoring has not been comprehensively explored. This research provides a complete understanding of the critical success factors from the client, the vendor or both the client and the vendor perspective. It also enables researchers to analyse ili rethink ili review offshoring in different service areas.

The sharp peak-flat trough pattern and critical speculation

OpenAIRE

Roehner, B. M.; Sornette, D.

1998-01-01

We find empirically a characteristic sharp peak-flat trough pattern in a large set of commodity prices. We argue that the sharp peak structure reflects an endogenous inter-market organization, and that peaks may be seen as local ``singularities'' resulting from imitation and herding. These findings impose a novel stringent constraint on the construction of models. Intermittent amplification is not sufficient and nonlinear effects seem necessary to account for the observations.

How Offshore Outsourcing Affects Costs and Value Creation

DEFF Research Database (Denmark)

Brandl, Kristin; Mol, Michael J.

2012-01-01

Although academic and public interest in service offshoring has increased in recent years, research remains focused mainly on antecedents and benefits of activities, overlooking process aspects. For that reason, we take a process perspective when conceptualizing around offshore outsourcing...... affects costs and value creation in the respective stages. The reconceptualization enables us to provide a clearer and more fine-grained picture of the effects of offshoring and outsourcing decisions, thus helping to further develop our understanding of the reasoning to relocate services geographical...

DEVELOPMENT AND PRELIMINARY TESTING OF A PARABOLIC TROUGH SOLAR WATER HEATER

Directory of Open Access Journals (Sweden)

O. A. Lasode

2011-06-01

Full Text Available Solar energy is a high-temperature, high-energy radiant energy source, with tremendous advantages over other alternative energy sources. It is a reliable, robust renewable resource which is largely undeveloped. The design and fabrication of parabolic trough solar water heater for water heating was executed. The procedure employed includes the design, construction and testing stages. The equipment which is made up of the reflector surface (curved mirror, reflector support, absorber pipe and a stand was fabricated using locally sourced materials. The results obtained. compared favourably with other research works in the literature. It depicts that employing a suitable design, selection of time of heating and proper focusing of the reflected rays to the focal spot region, solar radiation can efficiently be utilized for water heating in a tropical environment. This work presents a parabolic trough solar water heater as a suitable renewable energy technology for reducing water-heating costs.

Coordinated control of wind power plants in offshore HVDC grids

DEFF Research Database (Denmark)

Sakamuri, Jayachandra N.

2017-01-01

power between different countries, and different synchronous areas. It is very likely that they will then be combined with offshore wind power plant (OWPP) connections in the North Sea, transforming it in a multi terminal DC (MTDC) grid and, therefore, in a fully meshed offshore DC grid in near future......During the recent years, there has been a significant penetration of offshore wind power into the power system and this trend is expected to continue in the future. The North Sea in Europe has higher potential for offshore wind power; therefore, the North Seas Countries' Offshore Grid initiative....... However, increased penetration of offshore wind power into the power system poses several challenges to its security. This thesis deals with two main research challenges, (1) Develop, and analyze the coordinated control strategies for AC voltage and reactive power control in the cluster of OWPPs connected...

The environmental impact from an offshore plant

International Nuclear Information System (INIS)

Larsson, A.-K.

1994-01-01

Wind measurements in different countries have shown the existence of a large energy potential in offshore winds. Taking into consideration the limited suitable area on land for wind power plants it is essential to know the environmental influence from and on an offshore plant. The first offshore wind power plant was built in Sweden in 1990 in order to examine the influence on birds, fish and fishing, shipping, public opinion, maintenance and the effects on foundation from waves and ice. So far, the programme shows that the birds try to avoid the plant by flying further away from it out over the sea. (Author)

Offshore Financial Centers in Global Capital Flow

Directory of Open Access Journals (Sweden)

Lutsyshyn Zoriana

2017-12-01

Full Text Available The article is dedicated to investigation of the place and role of offshore financial centers in financial globalization system, and of the reasons for using offshores in assets securitization mechanism. Numerous offshore and other preferential zones enabling to avoid the effective national and governmental tax regime are important attributes of global financial system and redistributive links of world financial flows. At present, around 70 countries and territories offer their offshore services for foreign capital, bank transactions, profitability from activities in financial markets proper. The global offshore business concentrates large amounts often having no relation to the country of origin, the so-called cosmopolitan capital (wandering. Although in the early 80's of the XXth century offshore companies were considered to control approximately 500 billion dollars, it was already in the early 90's that this amount doubled and was estimated as 1 trillion dollars. Today, from ⅓ to half of the world capital turnover goes through offshore business channels, and therefore, almost half of non-resident bank deposits are concentrated in world offshore centers. These are the world financial centers comprising international capital markets that provide for the accumulation and redistribution of world capital. From the process of reproduction (circulation of capital, the world financial centers plunge out the most homogeneous and mobile element — money, and freely manipulating with them, concentrate huge economic power in their hands. The role of world financial centers was also enhanced by the latest achievements in computer science, allowing execution of instant transactions and movement of huge amounts to any point of the world within the shortest possible time. The world financial centers consist not only of powerful banks and financial institutions operating on the international scene, but also have currency, stock and other exchanges as their

New Models for Maintenance of Offshore Wind Farms

DEFF Research Database (Denmark)

Petersen, Kristian R.

component that was causing a large amount of downtime were identified. Further analysis with the Reliability-Centred Maintenance concept helped determine the most appropriate maintenance strategy. In the final perspective, long-term strategic decisions were the focus. Asset Management and especially Asset...... Life-Cycle Management were studied using a case study. The case study analysis was used to generate strategies to help managers perform maintenance more proactively and to prepare the management of the offshore wind farm turbines for the future. Existing literature on Asset Life-Cycle Management has......Operations and maintenance (O&M) processes are important for keeping offshore wind turbines in operation. Costs related to such activities constitute approximately 30% of the lifetime cost of an offshore wind farm project. Currently, the offshore wind energy industry has shown a rapid increase...

Levels of Outsourcing and Offshoring

DEFF Research Database (Denmark)

Madsen, Erik Skov; Slepniov, Dmitrij

2011-01-01

The purpose of this paper is to examine the evolution of offshoring and outsourcing over time and highlight strategic considerations underpinning this process in companies. On the basis of four case studies of Danish and German industrial companies, this paper develops a holistic framework...... conceptualizing various levels of outsourcing and offshoring as well as factors driving the transition between these levels. The framework adds to better understanding of the process and challenges the linear nature of it and suggests that ‘backsourcing’ and repatriation of activities should receive more...

Offshore Outsourcing Induced by Domestic Providers

OpenAIRE

Yutian Chen; Pradeep Dubey; Debapriya Sen

2005-01-01

We show that offshore outsourcing can occur even when there are no economies of scale or cost advantages for the foreign firms. What drives the phenomenon is that domestic firms, by accepting orders for intermediate goods, incur the disadvantage of becoming Stackelberg followers in the ensuing competition to sell the final good. Thus they have incentive to quote high provider prices to ward off future competitors, compelling them to outsource offshore.

46 CFR 11.470 - Officer endorsements as offshore installation manager.

Science.gov (United States)

2010-10-01

... 46 Shipping 1 2010-10-01 2010-10-01 false Officer endorsements as offshore installation manager... Officer endorsements as offshore installation manager. (a) Officer endorsements as offshore installation manager (OIM) include: (1) OIM Unrestricted; (2) OIM Surface Units on Location; (3) OIM Surface Units...

Investigating the reasons of variability in Si IV and C IV broad absorption line troughs of quasars

Science.gov (United States)

Stathopoulos, Dimitrios; Lyratzi, Evangelia; Danezis, Emmanuel; Antoniou, Antonios; Tzimeas, Dimitrios

2017-09-01

In this paper we analyze the C IV and Si IV broad absorption troughs of two BALQSOs (J101056.69+355833.3, J114548.38+393746.6) to the individual components they consist of. By analyzing a BAL trough to its components we have the advantage to study the variations of the individual absorbing systems in the line of sight and not just the variations of the whole absorption trough or the variations of selected portions of BAL troughs exhibiting changes. We find that the velocity shifts and FWHMs (Full Width at Half Maximum) of the individual components do not vary between an interval of six years. All variable components show changes in the optical depths at line centers which are manifested as variations in the EW (Equivalent Width) of the components. In both BALQSOs, over corresponding velocities, Si IV has higher incidence of variability than C IV. From our analysis, evidence is in favour of different covering fractions between C IV and Si IV. Finally, although most of our results favour the crossing cloud scenario as the cause of variability, there is also strong piece of evidence indicating changing ionization as the source of variability. Thus, a mixed situation where both physical mechanisms contribute to BAL variability is the most possible scenario.

Conceptual Model of Offshore Wind Environmental Risk Evaluation System

Energy Technology Data Exchange (ETDEWEB)

Anderson, Richard M.; Copping, Andrea E.; Van Cleve, Frances B.; Unwin, Stephen D.; Hamilton, Erin L.

2010-06-01

In this report we describe the development of the Environmental Risk Evaluation System (ERES), a risk-informed analytical process for estimating the environmental risks associated with the construction and operation of offshore wind energy generation projects. The development of ERES for offshore wind is closely allied to a concurrent process undertaken to examine environmental effects of marine and hydrokinetic (MHK) energy generation, although specific risk-relevant attributes will differ between the MHK and offshore wind domains. During FY10, a conceptual design of ERES for offshore wind will be developed. The offshore wind ERES mockup described in this report will provide a preview of the functionality of a fully developed risk evaluation system that will use risk assessment techniques to determine priority stressors on aquatic organisms and environments from specific technology aspects, identify key uncertainties underlying high-risk issues, compile a wide-range of data types in an innovative and flexible data organizing scheme, and inform planning and decision processes with a transparent and technically robust decision-support tool. A fully functional version of ERES for offshore wind will be developed in a subsequent phase of the project.

Effects of Accretionary Prisms on 3-D Long-Period Ground Motion Simulations

Science.gov (United States)

Guo, Y.; Koketsu, K.; Miyake, H.

2014-12-01

The accretionary prism along the subduction zones such as the Middle America trench or the Nankai trough is considered as an important factor affecting the generation and propagation of long-period ground motions. In Japan, the great earthquake along the Nankai subduction zone which is expected to occur in the near future can generate large long-period ground motions in the metropolitan areas such as Osaka, Nagoya and Tokyo. To investigate the effect of accretionary prism on long-period ground motions, we performed simulations of long-period ground motions for the event (Mw 7.1) that occurred off the Kii peninsula, Japan, at 10:07 on 5 September 2004 (UTC). Our simulation model ranged from the Kinki region to the Kanto region, and included the Osaka, Nobi and Kanto basin. We calculated long-period ground motions for four types of 3-D velocity structure models: (a) model with the accretionary prism (reference model), (b) model where accretionary prism has different 3-D geometry from the reference model, (c) model with the accretionary prism whose velocity, density and Q-value are shifted, (d) model without the accretionary prism. We compared the waveforms calculated for these models and concluded that the accretionary prism along the Nankai subduction zone plays roles in reducing the amplitude of direct waves and extending the duration of coda waves. This is attributed to the trap effect of accretionary prism. Our simulation also suggested that, the edge geometry along the landward side of accretionary prism has major effects on the processes of generation and propagation of long-period ground motions.

Structural control of the Gagua "Wedge" Zone east of Taiwan Island on the southern Okinawa Trough

Institute of Scientific and Technical Information of China (English)

ZHENG; Yanpeng; LIU; Baohua; WU; Jinlong; LIANG; Ruicai; L

2005-01-01

Based on compositive analysis and interpretation of the observed and historical data, the geophysical field characters and structural properties of the Gagua "Wedge" Zone of the sea area east of Taiwan Island and the primary tectonic stress direction and its variabilities of backarc spreading in the southern Okinawa Trough are studied. It is concluded from the study results that the Gagua "Wedge" Zone is structurally consistent with the Gagua ridge and two fault basins on both sides of the Gagua ridge, and adjusts the moving direction and distance of the western Philippine Sea plate to make the northwestward motion of the plate on its east side change to the northward subduction of the plate on its west side so that the primary tectonic stress direction of the Okinawa Trough changed from NW-SE to nearly N-S, which provided the stress source for the Okinawa Trough to enter the second spreading stage.

Nearshore versus Offshore

DEFF Research Database (Denmark)

Klinge Jacobsen, Henrik; Hevia Koch, Pablo Alejandro; Wolter, Christoph

Currently there exist high expectations for the development of wind energy, particularly in Europe, out of whichoffshore wind turbine developments will be central as tools to achieve current energy targets. The question betweennearshore and (far)-offshore is particularly relevant, both because of...

Federal Offshore Statistics, 1993. Leasing, exploration, production, and revenue as of December 31, 1993

Energy Technology Data Exchange (ETDEWEB)

Francois, D.K.

1994-12-31

This document contains statistical data on the following: federal offshore lands; offshore leasing activity and status; offshore development activity; offshore production of crude oil and natural gas; federal offshore oil and natural gas sales volume and royalties; revenue from federal offshore leases; disbursement of federal offshore revenue; reserves and resource estimates of offshore oil and natural gas; oil pollution in US and international waters; and international activities and marine minerals. A glossary is included.

A novel floating offshore wind turbine concept

DEFF Research Database (Denmark)

Vita, Luca; Schmidt Paulsen, Uwe; Friis Pedersen, Troels

2009-01-01

This paper will present a novel concept of a floating offshore wind turbine. The new concept is intended for vertical-axis wind turbine technology. The main purpose is to increase simplicity and to reduce total costs of an installed offshore wind farm. The concept is intended for deep water...... and large size turbines....

Offshore Wind Power

DEFF Research Database (Denmark)

Negra, Nicola Barberis

reliability models, and a new model that accounts for all relevant factors that influence the evaluations is developed. According to this representation, some simulations are performed and both the points of view of the wind farm owner and the system operator are evaluated and compared. A sequential Monte...... Carlo simulation is used for these calculations: this method, in spite of an extended computation time, has shown flexibility in performing reliability studies, especially in case of wind generation, and a broad range of results which can be evaluated. The modelling is then extended to the entire power......The aim of the project is to investigate the influence of wind farms on the reliability of power systems. This task is particularly important for large offshore wind farms, because failure of a large wind farm might have significant influence on the balance of the power system, and because offshore...

A trough for improved SFG spectroscopy of lipid monolayers

Science.gov (United States)

Franz, Johannes; van Zadel, Marc-Jan; Weidner, Tobias

2017-05-01

Lipid monolayers are indispensable model systems for biological membranes. The main advantage over bilayer model systems is that the surface pressure within the layer can be directly and reliably controlled. The sensitive interplay between surface pressure and temperature determines the molecular order within a model membrane and consequently determines the membrane phase behavior. The lipid phase is of crucial importance for a range of membrane functions such as protein interactions and membrane permeability. A very reliable method to probe the structure of lipid monolayers is sum frequency generation (SFG) vibrational spectroscopy. Not only is SFG extremely surface sensitive but it can also directly access critical parameters such as lipid order and orientation, and it can provide valuable information about protein interactions along with interfacial hydration. However, recent studies have shown that temperature gradients caused by high power laser beams perturb the lipid layers and potentially obscure the spectroscopic results. Here we demonstrate how the local heating problem can be effectively reduced by spatially distributing the laser pulses on the sample surface using a translating Langmuir trough for SFG experiments at lipid monolayers. The efficiency of the trough is illustrated by the detection of enhanced molecular order due to reduced heat load.

Multi-parameter optimization design of parabolic trough solar receiver

International Nuclear Information System (INIS)

Guo, Jiangfeng; Huai, Xiulan

2016-01-01

Highlights: • The optimal condition can be obtained by multi-parameter optimization. • Exergy and thermal efficiencies are employed as objective function. • Exergy efficiency increases at the expense of heat losses. • The heat obtained by working fluid increases as thermal efficiency grows. - Abstract: The design parameters of parabolic trough solar receiver are interrelated and interact with one another, so the optimal performance of solar receiver cannot be obtained by the convectional single-parameter optimization. To overcome the shortcoming of single-parameter optimization, a multi-parameter optimization of parabolic trough solar receiver is employed based on genetic algorithm in the present work. When the thermal efficiency is taken as the objective function, the heat obtained by working fluid increases while the average temperature of working fluid and wall temperatures of solar receiver decrease. The average temperature of working fluid and the wall temperatures of solar receiver increase while the heat obtained by working fluid decreases generally by taking the exergy efficiency as an objective function. Assuming that the solar radiation intensity remains constant, the exergy obtained by working fluid increases by taking exergy efficiency as the objective function, which comes at the expense of heat losses of solar receiver.

Scour around Offshore Wind Turbine Foundations

DEFF Research Database (Denmark)

Petersen, Thor Ugelvig

Over the last decades several offshore wind farms have been installed and commissioned in the European waters. Typically the foundations of the wind turbines are protected against scour at the base by installing scour protection with rock dump. The Egmond aan Zee offshore wind farm located about 10...... the performance (stability) of the scour protection and to quantify the edge scour development at the circumference of the scour protection. The survey campaign showed considerable edge scour of up to 2.7 m, which was expected from design considerations. However, no clear information exists on the mechanisms...... causing the edge scour development around scour protections at offshore wind turbine foundations. The purpose of the present thesis is to investigate and explain the development of the edge scour in such applications, and describe the flow mechanism causing the scour. Furthermore, the dissertation also...

Cenozoic evolution of the Vietnamese coastal margin

Energy Technology Data Exchange (ETDEWEB)

Fyhn, M.B.W.; Nielsen, Lars Henrik; Boldreel, L.O. (Geological Survey of Denmark and Greenland, Copenhagen (DK))

2007-10-15

One of the main risk factors regarding petroleum exploration in the Vietnamese offshore basins is the presence of adequate source rock intervals. Onshore data from the ENRECA-1 core through the Song Ba Trough in central Vietnam show, however, that thick intervals of excellent oil- and gas-prone lacustrine mudstone and humic coals may develop even in small basins characterised by high sediment input. Although the Song Ba Trough is an order of magnitude smaller than the Vietnamese offshore basins, seismic data in the latter show apparent depositional similarities suggesting the presence of similar high-quality source rocks in the offshore basins. In addition, seismic facies analysis as well as oil and gas compositions indicate that other source rock types, such as Neogene fluvio-deltaic coals, carbonaceous shales and fore-reef marls are present in some of the basins and thus testify to the great petroleum potential of the Vietnamese margin. (LN)

Nearshore and offshore environmental effects monitoring at the Sable Offshore Energy project

International Nuclear Information System (INIS)

Hurley, G. V.

2000-01-01

A monitoring program to determine whether any temporary or permanent environmental perturbations may be attributable to the Sable offshore gas pipeline project as it approaches landfall at Goldboro through an outer bay is discussed, This nearshore region is an active fishing region for the residents of Goldboro, hence the concern about possible contamination. The monitoring project began with a baseline study, followed by monitoring the construction and the recovery period following construction, to ensure that any persistent changes to the nearshore aquatic environment were documented. The monitoring study included representatives of the fishing community to ensure that concerns are addressed early and on a continuing basis. At various phases of the project water properties,sediment modelling, the effects of construction on sea bottom conditions, benthic biota and cultivated mussels, water quality, phytoplankton, and resuspension of toxic cysts, terns and other seabirds were studied. Monitoring programs were also established for sea urchins and mussels, two important commercial species. Commercial-sized sea urchins showed a decrease of 60 per cent between 1998 and 1999 (i.e. the construction period). Recovery of sea urchin population in the immediate trench region will be the special focus of the post-construction monitoring phase. Mussel spat settlement and mussel tissue condition, lobster trapping, water properties, and bird behaviour showed no measurable changes during construction monitoring. In addition to these studies there is an ongoing offshore monitoring program in effect by Sable Offshore Energy Inc., put in place as a condition of approval of its Development Plan by the Canada-Nova Scotia Offshore Petroleum Board. This program monitors attributes such as water quality, suspended particulate matter in the benthic boundary layer, sediment quality, the benthic habitat and megafaunal community, shellfish body burden and taint, marine mammals and seabirds

Fair shares: a preliminary framework and case analyzing the ethics of offshoring.

Science.gov (United States)

Gordon, Cameron; Zimmerman, Alan

2010-06-01

Much has been written about the offshoring phenomenon from an economic efficiency perspective. Most authors have attempted to measure the net economic effects of the strategy and many purport to show that "in the long run" that benefits will outweigh the costs. There is also a relatively large literature on implementation which describes the best way to manage the offshoring process. But what is the morality of offshoring? What is its "rightness" or "wrongness?" Little analysis of the ethics of offshoring has been completed thus far. This paper develops a preliminary framework for analyzing the ethics of offshoring and then applies this framework to basic case study of offshoring in the U.S. The paper following discusses the definition of offshoring; shifts to the basic philosophical grounding of the ethical concepts; develops a template for conducting an ethics analysis of offshoring; applies this template using basic data for offshoring in the United States; and conducts a preliminary ethical analysis of the phenomenon in that country, using a form of utilitarianism as an analytical baseline. The paper concludes with suggestions for further research.

World offshore energy loss statistics

International Nuclear Information System (INIS)

Kaiser, Mark J.

2007-01-01

Offshore operations present a unique set of environmental conditions and adverse exposure not observed in a land environment taking place in a confined space in a hostile environment under the constant danger of catastrophe and loss. It is possible to engineer some risks to a very low threshold of probability, but losses and unforeseen events can never be entirely eliminated because of cost considerations, the human factor, and environmental uncertainty. Risk events occur infrequently but have the potential of generating large losses, as evident by the 2005 hurricane season in the Gulf of Mexico, which was the most destructive and costliest natural disaster in the history of offshore production. The purpose of this paper is to provide a statistical assessment of energy losses in offshore basins using the Willis Energy Loss database. A description of the loss categories and causes of property damage are provided, followed by a statistical assessment of damage and loss broken out by region, cause, and loss category for the time horizon 1970-2004. The impact of the 2004-2005 hurricane season in the Gulf of Mexico is summarized

Quantifying the hurricane risk to offshore wind turbines.

Science.gov (United States)

Rose, Stephen; Jaramillo, Paulina; Small, Mitchell J; Grossmann, Iris; Apt, Jay

2012-02-28

The U.S. Department of Energy has estimated that if the United States is to generate 20% of its electricity from wind, over 50 GW will be required from shallow offshore turbines. Hurricanes are a potential risk to these turbines. Turbine tower buckling has been observed in typhoons, but no offshore wind turbines have yet been built in the United States. We present a probabilistic model to estimate the number of turbines that would be destroyed by hurricanes in an offshore wind farm. We apply this model to estimate the risk to offshore wind farms in four representative locations in the Atlantic and Gulf Coastal waters of the United States. In the most vulnerable areas now being actively considered by developers, nearly half the turbines in a farm are likely to be destroyed in a 20-y period. Reasonable mitigation measures--increasing the design reference wind load, ensuring that the nacelle can be turned into rapidly changing winds, and building most wind plants in the areas with lower risk--can greatly enhance the probability that offshore wind can help to meet the United States' electricity needs.

Influence of the monsoon trough on air-sea interaction in the head of the Bay of Bengal during the southwest monsoon of 1990 (monsoon trough boundary layer experiment - 90)

Digital Repository Service at National Institute of Oceanography (India)

Sarma, Y.V.B.; Seetaramayya, P.; Murty, V.S.N.; Rao, D.P.

programme reveals considerable temporal variability in sea-level pressure, sea-surface temperature (SST) and the fluxes of heat and momentum at the air-sea interface. This variability is related closely to the north-south movement of the monsoon trough...

Unique ecological impacts associated with offshore floating nuclear power plants

International Nuclear Information System (INIS)

Adams, S.M.; McLean, R.B.

1979-01-01

The ecological impacts that could occur as a result of site construction and operation of an offshore floating nuclear power plant are identified by comparing the principal ecological features associated with offshore siting with those associated with the siting of onshore estuarine plants. In general, the ecological impacts of offshore nuclear plants should be relatively smaller than those of estuarine plants. Possible factors that could increase the relative impacts of offshore plants are high frequency of contact with schools of fish, siting near inlets to estuaries or other ecologically important areas, and the persistence of halogen residuals. Identifying the potential ecological impacts associated with the siting of offshore plants permits the development of various monitoring programs and measures to minimize these impacts

Synthetic seismograms in laterrally heterogeneous anelastic media: Modal summation for the case of offshore seismic sources (deep-sea trough)

International Nuclear Information System (INIS)

Alvarez, Leonardo; Romanelli, Fabio; Panza, Giuliano F.

2001-12-01

While waiting for the increment of strong motion data, especially for earthquake prone areas outside the United States and Japan, a very useful approach to perform immediate site specific seismic hazard assessment is the development and use of modelling tools. They are based, on one hand, on the theoretical knowledge of the physics of the seismic source and of wave propagation and, on the other hand, on the exploitation of the relatively rich database, already available, that can be used for the definition of the source and structural models. With these input data we model the ground motion using the mode-coupling approach for sharply varying laterally heterogeneous anelastic media, i.e. computing the coupling coefficients for the modes transmitted and reflected at the vertical interface, between two quarter spaces in welded contact. The formalism can be readily applied to any laterally heterogeneous structure by using a custom series of layered anelastic structures in welded contact at vertical interfaces. The case of seismic wave propagation in smooth varying laterally heterogeneous layered media, is solved with an approximation, equivalent to WKBJ method. The theoretical formulation that combines both WKBJ and the coupling coefficients approaches, is implemented in a computer program package. The computer code we have developed allows us to calculate synthetic seismograms for a wide range of laterally inhomogeneous layered anelastic media. As a case study we use an earthquake which occurred on December 16, 1999 (m b =4.8) beneath the Bartlett sea trough, south of Santiago de Cuba city, that was recorded by an accelerometer (SMA-100) placed in Rio Carpintero (RCC) station, at an epicentral distance of about 30 Km. The path travelled by the waves corresponds to a complex structure from undersea source to inland seismic station. A good fit between the observed transverse component (SH-waves) of acceleration and the corresponding synthetic signal is obtained for a

Floating offshore turbines

DEFF Research Database (Denmark)

Tande, John Olav Giæver; Merz, Karl; Schmidt Paulsen, Uwe

2014-01-01

metric of energy production per unit steel mass. Floating offshore wind turbines represent a promising technology. The successful operation of HyWind and WindFloat in full scale demonstrates a well advanced technology readiness level, where further development will go into refining the concepts, cost...

INORE: The International Network on Offshore Renewable Energy

International Nuclear Information System (INIS)

Martini, Michele; De Andrén, Andrés

2015-01-01

The International Network on Offshore Renewable Energy (INORE) is a non-profit organization run by volunteers. INORE was born to support early stage researchers in the offshore renewable energy field. Today, INORE has more than 1200 members from more than 70 different countries. The aim of this organization is to facilitate networking and information exchange between young researchers and professionals. This is achieved by arranging symposia, workshops, networking events and issuing scholarships. Three main knowledge areas are currently within INORE’s dedication: sea wave energy, tidal current energy and offshore wind energy.

Increased water contamination and grow-out Pekin duck mortality when raised with water troughs compared to pin-metered water lines using a United States management system

Science.gov (United States)

Schenk, A.; Porter, A. L.; Alenciks, E.; Frazier, K.; Best, A. A.; Fraley, S. M.; Fraley, G. S.

2016-01-01

Controversy has developed as to whether or not pin-metered water lines or water troughs are more appropriate for Pekin ducks. We hypothesized that water troughs would show improved duck body conditions and environmental quality compared to pin-metered water lines. To test this hypothesis, we housed ducks in 2 barns, one with water lines and one with water troughs. Water troughs were constructed to meet RSPCA guidelines for number and density of ducks and with recently described verandas. Ducks were divided into 4 pens per barn (n = 1,000 ducks/pen). The study was then repeated (n = 8 pens per water source) in a cross-over design so the barns each contained the opposite water source to the first experiment. We scored the ducks’ body condition using an established scoring rubric and analyzed using SAS Proc GLM-Mix as binomial data. Ducks housed with water troughs showed higher (thus worse condition; P duck mortality using a Student t test for both water sources each week. We found that the water troughs showed higher iron (P Ducks housed with water troughs used greater (P = 0.001) volumes of water compared to ducks housed with water lines. Ducks with water troughs also showed a greater percent (P = 0.008) mortality at all ages compared to ducks with water lines. These data suggest that water troughs may not be beneficial for duck welfare and could adversely impact both environment and duck or human health. PMID:26769272

Trajetórias tecnológicas no segmento offshore: ambiente e oportunidades Technological trajectories in the offshore segment: enviroment and opportunities

Directory of Open Access Journals (Sweden)

José Benedito Ortiz Neto

2008-08-01

Full Text Available Este artigo apresenta as diferentes trajetórias tecnológicas do segmento offshore na indústria petrolífera mundial considerando os seus principais aspectos e marcos constituintes. Mais especificamente, serão analisadas as trajetórias diferentes nas duas primeiras grandes províncias de petróleo do segmento offshore: o Golfo do México (EUA e o Mar do Norte (Europa. Junto com a Bacia de Campos (Brasil, são as mais produtivas e ricas do planeta e onde as três trajetórias tecnológicas foram desenvolvidas. Esse levantamento histórico é importante porque resgata os elementos que dão as bases do conhecimento tecnológico que permitiu à Petrobras, de forma inédita, iniciar as suas atividades offshore nas décadas de 1960-1970. Será visto aqui que a exploração offshore significou o surgimento de um novo paradigma tecnológico sustentado por três trajetórias.This article presents different technological trajectories concerning the offshore exploration segment in the world petroleum industry, considering their main aspects and components. More specifically, different trajectories will be analyzed in the first two largest crude oil territories: Gulf of Mexico (USA and Sea North (Europe. These, along with Bacia de Campos in Brazil, are the most productive and the richest regions in the planet and, therefore, where the three technological trajectories have been developed. This historic survey is important because it reveals the elements that provide the basis for technological knowledge, which allowed Petrobras to start its offshore activities in the 60s and 70s, via an original technology. The offshore exploration meant the emergence of a new technological paradigm supported by three trajectories.

De-offshorization as a Factor of Development of the National Economy

Directory of Open Access Journals (Sweden)

Galina S. Panova

2014-01-01

Full Text Available The article shows that the concept of "de-offshorization" is interpreted in the economic literature. On the one hand, de-offshorization is seen as a fight against offshore or tightening control over operations in offshore areas, and on the other as facilitating business environment and as a factor of development of the national economy. However, these approaches are not contrary to the understanding of the de-offshorization as a State policy aimed at improving the tax, legislative, enforcement and information sphere of activity of economic entities to reduce capital flight and repatriation. The analysis of the objectives and characteristics of the formation of offshore zones in the world and it is concluded that in general the offshore zone, favorable tax to optimize international economic cooperation, including trade and entrepreneurship. The article stresses that Russia currently has two approaches, the adherents of which have opposing views on combat offshore. Some consider that the need to impose a ban on business that manages the Russian business from foreign jurisdictions and prints there. Others are convinced that first of all it is necessary to improve the conditions for business in Russia, and then to demand the return of money. The authors offer a comprehensive solution to the problem of de-offshorization of the economy, which, in their view, should include not only economic, but also political, institutional, legal, fiscal and administrative components. In General, to ensure a stable, clear, transparent and objective rules of business in all sectors, to make the illegal withdrawal of capital/assets in offshore areas has a reputation and uneconomical. To this end, to take practical measures aimed at improving the transparency of the offshore business. In particular, the promising directions of the de-offshorization the Russian economy with international experience are defined: development and improvement of the financial, fiscal

Availability evaluation of offshore wind energy networks within the Dutch power system

NARCIS (Netherlands)

Tuinema, B.W.; Gibescu, M.; Kling, W.L.

2010-01-01

In the future, a large-scale expansion of offshore wind energy is expected in the Netherlands. For this large-scale expansion, a well-designed offshore network is needed. Different network configurations will lead to other availability of the offshore network and therefore also the offshore wind

The offshore trend: Structural changes in the wind power sector

International Nuclear Information System (INIS)

Markard, Jochen; Petersen, Regula

2009-01-01

In recent years, the wind power sector has begun to move offshore, i.e. to use space and good wind speeds on the open sea for large scale electricity generation. Offshore wind power, however, is not just technologically challenging but also a capital intensive and risky business that requires particular financial and organizational resources not all potential investors might have. We therefore address the question, what impact offshore wind power may have on ownership and organizational structures in the wind power sector. We compare on- and offshore wind park ownership in Denmark, the UK and Germany. The analysis shows that offshore wind power in all three countries is dominated by large firms, many of which are from the electricity sector. In Denmark and the UK, also investors from the gas and oil industry play an important role in the offshore wind business. This development represents a major shift for countries such as Germany and Denmark, in which the wind power sector has grown and matured on the basis of investments by individuals, farmers, cooperatives and independent project developers. The structural changes by which offshore wind power is accompanied have consequences for turbine manufacturers, project developers, investors, associations and policy makers in the field.

Upstream sediment input effects on experimental dune trough scour in sediment mixtures

NARCIS (Netherlands)

Kleinhans, M.G.

2005-01-01

Understanding causes of dune irregularity, especially dune trough scour, is important for the modeling of vertical sorting of sediment mixtures in morphological models of rivers with sediment mixtures. Sediment in dunes is generally sorted in a fining-upward manner, which affects the sediment

Offshore environmental aspects

NARCIS (Netherlands)

Lindeboom, H.J.; Degraer, S.

2016-01-01

The number of offshore wind farms (OWFs) is increasing rapidly, leading to questions about the cumulative environmental impact of such farms. The major impacts are caused by the noise produced in the building phase, the new hard substratum, the moving rotor blades, possible underwater noise in

Review report 2004. The Danish offshore wind farm demonstration project: Horns Rev and Nysted offshore wind farms. Environmental impact assessment and monitoring

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-10-15

The present review report presents the two wind farms Horns Rev and Nysted with regard to environmental characteristics and the results of the environmental studies carried out in connection with the Environmental Impact Assessment (EIA) and the baseline and monitoring programmes at the two sites. The descriptions of the programmes are based on extracts from the individual annual reports. Detailed information on method, programmes and conclusions can be found in these reports (see Appendix 1). This review report is divided into two parts. The first part contains a description of the potential environmental impacts of offshore wind farms and the potentially affected part of the environment. The second part includes a description of Horns Rev and Nysted Offshore Wind Farm and the environmental studies carried out here until the end of 2003. Appendix I is a list of the literature published on the studies carried out at Horns Rev and Nysted Offshore Wind Farm. Appendix II is a list of some of the literature relevant to the demonstration projects but not directly related to the projects. The offshore wind farm situated in the Roedsand area is officially denoted Nysted Offshore Wind Farm, and in the present report the denotation 'Nysted' will be used as well when referring to Nysted Offshore Wind Farm. The denotation Roedsand will be used when referring to the actual area Roedsand. (au)

Review report 2003. The Danish offshore wind farm demonstration project: Horns Rev and Nysted offshore wind farms. Environmental impact assessment and monitoring

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-09-15

The present review report presents the two wind farms Homs Rev and Nysted, with regard to environmental characteristics and the results of the environmental studies carried out in connection with the Environmental Impact Assessment (EIA) and the baseline and monitoring programmes at the two sites. The descriptions of the programmes are based on extracts from the individual annual reports. Detailed information on methods, programmes and conclusions can be found in these reports. This review report is divided into two parts. The first part contains a description of the potential environmentally impacts of offshore wind farms and the potentially affected part of the environment. The second part includes a description of Horns Rev and Nysted Offshore Wind Farm and the environmental studies carried out here until the end of 2003. Appendix I is a list of the literature published on the studies carried out at Hors Rev and Nysted Offshore Wind Farm. Appendix II is a list of some of the literature relevant to the demonstration projects but not directly related to the projects. The offshore wind farm situated at the bdsand area is officially denoted Nysted Offshore Wind Farm, and in the present report the denotation 'Nysted' will be used as well when referring to Nysted Offshore Wind Farm. The denotation Roedsand will be used when referring to the actual area Roedsand. (au)

Review report 2004. The Danish offshore wind farm demonstration project: Horns Rev and Nysted offshore wind farms. Environmental impact assessment and monitoring

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-10-15

The present review report presents the two wind farms Horns Rev and Nysted with regard to environmental characteristics and the results of the environmental studies carried out in connection with the Environmental Impact Assessment (EIA) and the baseline and monitoring programmes at the two sites. The descriptions of the programmes are based on extracts from the individual annual reports. Detailed information on method, programmes and conclusions can be found in these reports (see Appendix 1). This review report is divided into two parts. The first part contains a description of the potential environmental impacts of offshore wind farms and the potentially affected part of the environment. The second part includes a description of Horns Rev and Nysted Offshore Wind Farm and the environmental studies carried out here until the end of 2003. Appendix I is a list of the literature published on the studies carried out at Horns Rev and Nysted Offshore Wind Farm. Appendix II is a list of some of the literature relevant to the demonstration projects but not directly related to the projects. The offshore wind farm situated in the Roedsand area is officially denoted Nysted Offshore Wind Farm, and in the present report the denotation 'Nysted' will be used as well when referring to Nysted Offshore Wind Farm. The denotation Roedsand will be used when referring to the actual area Roedsand. (au)

U.S. Offshore Wind Manufacturing and Supply Chain Development

Energy Technology Data Exchange (ETDEWEB)

Hamilton, Bruce Duncan [Navigant Consulting, Inc.

2013-02-22

The objective of the report is to provide an assessment of the domestic supply chain and manufacturing infrastructure supporting the U.S. offshore wind market. The report provides baseline information and develops a strategy for future development of the supply chain required to support projected offshore wind deployment levels. A brief description of each of the key chapters includes: » Chapter 1: Offshore Wind Plant Costs and Anticipated Technology Advancements. Determines the cost breakdown of offshore wind plants and identifies technical trends and anticipated advancements in offshore wind manufacturing and construction. » Chapter 2: Potential Supply Chain Requirements and Opportunities. Provides an organized, analytical approach to identifying and bounding the uncertainties associated with a future U.S. offshore wind market. It projects potential component-level supply chain needs under three demand scenarios and identifies key supply chain challenges and opportunities facing the future U.S. market as well as current suppliers of the nation’s land-based wind market. » Chapter 3: Strategy for Future Development. Evaluates the gap or competitive advantage of adding manufacturing capacity in the U.S. vs. overseas, and evaluates examples of policies that have been successful . » Chapter 4: Pathways for Market Entry. Identifies technical and business pathways for market entry by potential suppliers of large-scale offshore turbine components and technical services. The report is intended for use by the following industry stakeholder groups: (a) Industry participants who seek baseline cost and supplier information for key component segments and the overall U.S. offshore wind market (Chapters 1 and 2). The component-level requirements and opportunities presented in Section 2.3 will be particularly useful in identifying market sizes, competition, and risks for the various component segments. (b) Federal, state, and local policymakers and economic development

Paleocene stratigraphic plays in Uruguay offshore

International Nuclear Information System (INIS)

Morales, E; Soto, M; Ferro, S; Tomasini, J; De Santa Ana, H; Conti, B.; Veroslavsky, G.

2012-01-01

The Uruguayan continental margin offshore evolution is represented by three large mega sequences: pre rift, rift and post rift, which are correlated with other South Atlantic basins. The tectonic and stratigraphic knowledge about the Uruguayan offshore evolution enable a hydrocarbon potential approximation . The mapping of the seismic depositional sequences are covered by deep basins. The methodology used identify the migration of Uruguayan side depo centers such as the stratigraphic plays group in particular a prospective Paleocene sequence

Offshoring and Job Stability : Evidence from Italian Manufacturing

NARCIS (Netherlands)

Lo Turco, A.; Maggioni, D.; Picchio, M.

2012-01-01

Abstract: We study the relationship between offshoring and job stability in Italy in the period 1995–2001 by using an administrative dataset on manufacturing workers. We find that the international fragmentation of production negatively affects job stability. Service offshoring and material

Tracking local control of a parabolic trough collector. Control local de Seguimiento cilindro parabolico ACE 20

Energy Technology Data Exchange (ETDEWEB)

Ajona Maeztu, J.I.; Alberdi Primicia, J.; Gamero Aranda, E.; Blanco, J.

1991-01-01

In the local control, the sun position related to the trough collector is measured by two photo-resistors. the provided electronic signal is then compared with reference levels in order to get a set of 8 logical signals which form a byte. This byte and the commands issued by a programmable controller are connected to the inputs of a P.R.O.M. memory which is programmed with the logical ecuations of the control system. the memory output lines give the control commands of the parabolic trough collector motor. (author)

Tracking local control of a parabolic trough collector; Control local de Seguimiento cilindro parabolico ACE 20

Energy Technology Data Exchange (ETDEWEB)

Ajona Maeztu, J.I.; Alberdi Primicia, J.; Gamero Aranda, E.; Blanco, J.

1991-12-31

In the local control, the sun position related to the trough collector is measured by two photo-resistors. the provided electronic signal is then compared with reference levels in order to get a set of 8 logical signals which form a byte. This byte and the commands issued by a programmable controller are connected to the inputs of a P.R.O.M. memory which is programmed with the logical ecuations of the control system. the memory output lines give the control commands of the parabolic trough collector motor. (author)

Tracking local control of a parabolic trough collector; Control local de seguimiento cilindro parabolico ACE20

Energy Technology Data Exchange (ETDEWEB)

Ajona, J I; Alberdi, J; Gamero, E; Blanco, J

1992-07-01

In the local control, the sun position related to the trough collector is measured by two photo-resistors. The provided electronic signal is then compared with reference levels in order to get a set of B logical signals which form a byte. This byte and the commands issued by a programmable controller are connected to the inputs of o P.R.O.M. memory which is programmed with the logical equations of the control system. The memory output lines give the control command of the parabolic trough collector motor. (Author)

A numerical analysis of the energy behavior of a parabolic trough ...

African Journals Online (AJOL)

The solar power is a clean and a durable energy; there are several techniques for using them. When necessary to elevated temperatures of heat transfer fluid, this energy must concentration. This paper presents the efficiencies study of a linear solar concentrator of a parabolic trough type. This study was conducted on the ...

Canadian offshore standards become world model

International Nuclear Information System (INIS)

Reid, W.

2000-01-01

Newfoundland's emerging offshore industry is becoming known not only for its frontier petroleum exploration and development expertise, but it is also gaining international recognition for making good use of its experience to provide advice to future developers on how to deal with multiple levels of governments and community groups, infrastructure development, adverse effects on the local environment, society and the economy. The companies active offshore-Newfoundland have acquired world-class expertise from working their offshore oil fields on the Grand Banks. There is a steady demand for that expertise for application in other regions, mostly from oil-industry personnel. Requests for sharing that experience have come from the United States, Norway and Australia, but also from within Canada, particularly from British Columbia. In British Columbia, coastal exploration has been going on since the early 1900s, with increasing concern for the impact of petroleum activity on the coastal environment, culminating with the imposition of a moratorium in 1959. Now, the British Columbia government is interested in learning about the procedures it should follow to reach a decision on whether to lift the moratorium in effect (on and off) since 1959. The interest in possible resumption of exploration and development activity is motivated by recent studies by the Geological Survey of Canada, which suggest a hydrocarbon potential five times greater than the Hibernia oil field off Newfoundland. An indication of this interest in opening up the west coast to offshore exploration is the recent seminar at Memorial University in St. John's. Speakers at the seminar presented an overview of the lessons learned from the east coast, the social and economic impacts of offshore oil and gas development and how such development might co-exist with British Columbia's marine ecosystem and fishery resources

Canada-Nova Scotia Offshore Petroleum Board annual report, 1992-1993

International Nuclear Information System (INIS)

1993-06-01

The Canada-Nova Scotia Offshore Petroleum Board was established as the agency responsible for the regulation of the hydrocarbon resources in the Nova Scotia offshore. The Board evaluates resource potential, administers petroleum exploration and production rights, approves offshore activities, and approves benefits and development plans. The main activities of the Board in 1992-1993 are summarized and financial statements are presented. Highlights include production of 572,300 m 3 of oil during the first production season of LASMO Nova Scotia Ltd.'s Cohasset development, the first commercial offshore oil production for Canada; four major resource evaluation projects in the Glenelg Field, the Laurentian sub-basin, the Fundy Rift Basin, and the Panuke Field; holding of discussions between Nova Scotia, Newfoundland, and Canada on the maritime boundary lines between respective offshore petroleum board jurisdictions, in the wake of a June 1992 determination of the disputed maritime boundary around St. Pierre et Miquelon; and amendments of certain safety-related legislation applicable to offshore operations. Employment benefits of the Cohasset project during 1992 totalled ca 470 Nova Scotians and 120 other Canadians. 3 tabs

Mid-Atlantic Offshore Wind Interconnection and Transmission (MAOWIT)

Energy Technology Data Exchange (ETDEWEB)

Kempton, Willett [Univ. of Delaware, Newark, DE (United States)

2016-04-05

This project has carried out a detailed analysis to evaluate the pros and cons of offshore transmission, a possible method to decrease balance-of-system costs and permitting time identified in the DOE Office Wind Strategic Plan (DOE, 2011). It also addresses questions regarding the adequacy of existing transmission infrastructure and the ability of existing generating resources to provide the necessary Ancillary Services (A/S) support (spinning and contingency reserves) in the ISO territory. This project has completed the tasks identified in the proposal: 1. Evaluation of the offshore wind resource off PJM, then examination of offshore wind penetrations consistent with U.S. Department of Energy’s (DOE) targets and with their assumed resource size (DOE, 2011). 2. Comparison of piecemeal radial connections to the Independent System Operator (ISO) with connections via a high-voltage direct current (HVDC) offshore network similar to a team partner. 3. High-resolution examination of power fluctuations at each node due to wind energy variability 4. Analysis of wind power production profiles over the Eastern offshore region of the regional ISO to assess the effectiveness of long-distance, North- South transmission for leveling offshore wind energy output 5. Analysis of how the third and fourth items affect the need for ISO grid upgrades, congestion management, and demand for Ancillary Services (A/S) 6. Analysis of actual historic 36-hr and 24-hr forecasts to solve the unit commitment problem and determine the optimal mix of generators given the need to respond to both wind variability and wind forecasting uncertainties.

Hydropower flexibility and transmission expansion to support integration of offshore wind

DEFF Research Database (Denmark)

Cutululis, Nicolaos Antonio; Farahmand, Hossein; Jaehnert, S.

2016-01-01

is one of the fast responding sources of electricity, thus power systems with considerable amounts of flexible hydro power can potentially offer easier integration of offshore wind power. The interaction between offshore wind and hydro power can be benefic, especially when looking at how the flexibility......In 2013, offshore wind grew over 50%. This increase, concentrated in a relatively small geographical area, can lead to an increased variability of the power produced by offshore wind. The variability is one of the key issues, along transmission, in integrating offshore wind power. Hydro power...... of hydro generation can match the variability of offshore wind, allowing for larger shares of variable generation to be integrated in the power systems without decreasing its stability. The analysis includes two interrelated models, a market model and a flow-based model. The results show that hydropower...

Theoretical Study of the Compound Parabolic Trough Solar Collector

OpenAIRE

Dr. Subhi S. Mahammed; Dr. Hameed J. Khalaf; Tadahmun A. Yassen

2012-01-01

Theoretical design of compound parabolic trough solar collector (CPC) without tracking is presented in this work. The thermal efficiency is obtained by using FORTRAN 90 program. The thermal efficiency is between (60-67)% at mass flow rate between (0.02-0.03) kg/s at concentration ratio of (3.8) without need to tracking system.The total and diffused radiation is calculated for Tikrit city by using theoretical equations. Good agreement between present work and the previous work.

76 FR 24504 - National Offshore Safety Advisory Committee

Science.gov (United States)

2011-05-02

... DEPARTMENT OF HOMELAND SECURITY [Docket No. USCG-2011-0183] National Offshore Safety Advisory... Committee Meeting. SUMMARY: The National Offshore Safety Advisory Committee (NOSAC) will meet on May 19... completed its business. ADDRESSES: The meeting will be held at Wyndham Riverfront Hotel, Bacchus room, 701...

Offshore wind investments – Realism about cost developments is necessary

International Nuclear Information System (INIS)

Schwanitz, Valeria Jana; Wierling, August

2016-01-01

Data available from the recent boom in European offshore wind investments contradict widely held expectations about a decline in costs per kW. Our review shows that scenario projections for investment costs are systematically flawed by over-optimistic assumptions. Contrasting offshore wind technology with onshore wind and nuclear power, we argue that offshore wind could be a candidate for negative learning since a trend towards more complex OWP (offshore wind parks) exists and uncertainty remains high. We estimate technical uncertainty and input cost uncertainty to calculate whether investments in offshore wind technology are profitable today. Applying a real option model to two reference plants using empirically derived parameter values, we allow for sunk cost and the possibility to abandon the investment. We find that for a large parameter range, investments are not profitable, even with substantial support such as feed-in tariffs under the German Energy Act. Therefore, policy incentives for building larger and more complex offshore wind parks bear a high risk to fail in their aim of bringing down investment costs. Policies that instead incentivize the optimization of offshore wind technology – in particular by increasing the load factor and material efficiency and bringing down decommissioning costs – are more sustainable. - Highlights: • We review offshore wind power investments. • Contrary to expectations costs increase. • It is unlikely to see a turn in the near future as complexity is growing. • We deploy an empirically based real option model. • Investments are not profitable across a large parameter range.

Revised guidance on reporting of offshore hydrocarbon releases

International Nuclear Information System (INIS)

1996-11-01

The application offshore of the Reporting of Injuries, Disease and Dangerous Occurrences Regulations 1995 (RIDDOR 1995) has resulted in a new statutory reporting form. The definitions in RIDDOR 95 covering offshore hydrocarbon releases have been slightly revised, making it necessary to revise the guidance on reporting of offshore hydrocarbon releases. RIDDOR 1995 does not affect the existing voluntary arrangements for completion of forms. The receipt of correctly completed forms is important to ensure good output data from the database, and the guidance contained in this document is therefore aimed at assisting completion of the voluntary form. (UK)

Five offshore wind farms by EDF, GDF Suez and Iberdrola. France; Vijf offshore windparken door EDF, GDF Suez en Iberdrola. Frankrijk

Energy Technology Data Exchange (ETDEWEB)

Polo-Leemreis, J. [TWA Netwerk, Paris (France)

2012-02-15

Five offshore wind farms are planned to be built off the Northwest coast of France. On 11 January 2012, three international consortia, led by the French businesses EDF EN (Energie Nouvelles), GDF Suez and the Spanish business Iberdrola, submitted their project proposals to this end. The French government highly values the contribution that offshore wind farms can make to the development of a new industrial sector. This would bring highly needed benefits to the French economy [Dutch] Voor de Noordwest-kust van Frankrijk moeten vijf offshore windparken komen. Op 11 januari 2012 hebben drie internationale consortia onder leiding van de Franse bedrijven EDF EN (Energies Nouvelles), GDF Suez en het Spaanse Iberdrola hun projectvoorstellen hiervoor ingediend. De Franse regering hecht veel waarde aan de bijdrage die offshore windparken kunnen leveren aan de ontwikkeling van een nieuwe industriele sector. De Franse economie zou dit goed kunnen gebruiken.

Offshore floating windmills

International Nuclear Information System (INIS)

1993-10-01

The aim was to produce a general survey of the profitability of establishing floating offshore wind turbine arrays and to compare this with the cost and profitability of constructing offshore arrays with fixed foundations and arrays located on land sites. Aspects of design in all cases are described, also into relation to the special demands placed on dimensioning in relation to the types of location and foundation. The costs of the offshore arrays are evaluated in relation to capacity under conditions in Danish waters. The advantage of floating arrays is that they can be placed far out to sea where they can not be seen from the coast and thus not be considered to spoil the marine view. But as the water gets deeper the cost of floating foundations rises. It was found that it would not be technologically profitable to establish floating arrays at a depth of less than 30 - 40 meters which means that only the outer Danish waters can be taken into consideration. For depths of up to 70 meters, individual floating bases are more expensive than fixed ones but would be cheaper if a number of windmills could share the same anchor. For depths of more than 70 meters floating foundations would be the cheapest. The cost is dependent on the depth and distance from the coast and also on wind conditions. The main conclusion is that currently the cost of establishing wind turbine arrays in deeper outer waters on floating foundations is comparable to that of arrays sited at inner waters on solid foundations placed on the sea bed. (AB) (20 refs.)

Trough Concentrations of Vancomycin in Patients Undergoing Extracorporeal Membrane Oxygenation.

Directory of Open Access Journals (Sweden)

So Jin Park

Full Text Available To investigate the appropriateness of the current vancomycin dosing strategy in adult patients with extracorporeal membrane oxygenation (ECMO, between March 2013 and November 2013, patients who were treated with vancomycin while on ECMO were enrolled. Control group consisted of 60 patients on vancomycin without ECMO, stayed in medical intensive care unit during the same study period and with the same exclusion criteria. Early trough levels were obtained within the fourth dosing, and maintenance levels were measured at steady state. A total of 20 patients were included in the analysis in ECMO group. Sixteen patients received an initial intravenous dose of 1.0 g vancomycin followed by 1.0 g every 12 hours. The non-steady state trough level of vancomycin after starting administration was subtherapeutic in 19 patients (95.00% in ECMO group as compared with 40 patients (66.67% in the control group (p = 0.013. Vancomycin clearance was 1.27±0.51 mL/min/kg, vancomycin clearance/creatinine clearance ratio was 0.90 ± 0.37, and elimination rate constant was 0.12 ± 0.04 h-1. Vancomycin dosingfrequency and total daily dose were significantly increased after clinical pharmacokinetic services of the pharmacist based on calculated pharmacokinetic parameters (from 2.10 ± 0.72 to 2.90 ± 0.97 times/day, p = 0.002 and from 32.54 ± 8.43 to 42.24 ± 14.62mg/kg, p = 0.014 in ECMO group in contrast with those (from 2.11 ± 0.69 to 2.37 ± 0.86 times/day, p = 0.071 and from 33.91 ± 11.85 to 31.61 ± 17.50 mg/kg, p = 0.350 in the control group.Although the elimination rate for vancomycin was similar with population parameter of non ECMO patients, the current dosing strategy of our institution for vancomycinin our ICU was not sufficient to achieve the target trough in the initial period in most patients receiving ECMO.

Offshore 2010. Final report; Offshore 2010. Sluttrapport

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

An overview of the accomplishments of the various projects that have received support from the Norwegian Research Council's program 'Offshore 2010'. The following projects are presented, some have English and some Norwegian project names: 'Critical parameters influencing inhibitor performance in multiphase flow', 'Development of the drilling optimization simulator (DDS) and a totally integrated drilling optimization system', 'Produksjonsoptimalisering og automatisk styring av broenner og roerledninger (PETRONICS)', 'Termisk isolerte undervannsroer for sikring av broenntransport over store avstander', 'Utvikling av magnetisk frekvensformer for styring av store subsea pumper paa havdyp ned mot 4000 meter', 'Flerfase stroemningsmaaler for permanent nedihulls installasjon', 'Hastighetsmaaling i flerfase stroemning ved passiv akustikk', 'Oil/water seperation offshore: optimized flow- and seperation behavior', 'Stroemningshastighet', 'A rock mechanics based reservoir simulation', 'MultiTool fase 2 - et flerbruksverktoey for nedihulls applikasjoner', 'Utvikling av undervanns olje-i-vann monitor for kontinuerlig maaling av lave oljekonsentrasjoner basert paa TR-LIFS', 'Subsea multipath ultrasonic liquid flow meter', 'Fluid characterization at elevated pressures and temperatures (Flucha II)'. The two main goals for the research program are 1. The development of new technology and competency in the field of downhole- and subsea processing and multiphase transportation, and 2. Innovation and commercialisation in small and medium sized companies (less than 100 employees). Some details on the financing and results are included (ml)

Present-day chaotic formations around the Japanese trenches: Comparison to the on land examples from the Shimanto and Miura-Boso, and from the Franciscan, Mineoka and Ankara

Science.gov (United States)

Ogawa, Yujiro; Kawamura, Kiichiro; Tsunogae, Toshiaki; Mori, Ryota; Chiba, Tae; Sasaki, Tomoyuki

2010-05-01

Four different types of chaotic formations were recognized by the submersible observation around the Japanese trenches, including the Nankai and Sagami troughs, Boso triple junction, Japan trench, and Izu-Bonin arc, and each type is summarized and discussed in view of comparison to the on land examples, such as from the Franciscan, Shimanto and Miura-Boso belts in the circum Pacifc margins, and the Ankara. The submarine geologies are present actual examples to give us a critical key to understanding the formation processes and emplacement mechanisms for the so-called mélange bodies, either sedimentary, tectonic or diapiric. Some are made of alternated beds of sandstone and mudstone that show broken or block-in-matrix fashion, in most cases in muddy matrix. These are commonly developed on the trench landward slope toe of the Nankai and Sagami troughs and Boso triple junction area as well as the Japan trench slope. One type is from the landward slope, but another type is from the oceanward slopes. The former type is in places calcareous cemented, probably caused by hydraulic fracturing by high pore pressure along the thrust fault and oxidized methane-made carbonate precipitation. They are seen on the feet of the thrust-dominated slope and to be compared to the so-called sedimentary mélanges due to the gravitational sliding, which occur because of tectonically induced steep slopes. Most of such thrusts are related to large subduction type earthquakes, and await for further critical consideration on to the relation to the asperity problem. Some of large scale gravitational collapses may be related to the seamount or ridge subduction to the trench, both in case of accretionary and non-accretionary type margins, the former is for the examples from the Nankai and Sagami troughs and the Boso triple junction, latter for the Japan trench. In all cases on land and under the sea in the trench landward slope, some calcareous breccias are associated with methane

Offshore Wind Turbines Situated in Areas with Strong Currents

DEFF Research Database (Denmark)

Jensen, Morten S.; Juul Larsen, Brian; Frigaard, Peter

Prediction of local scour caused by offshore wind turbine foundations using empirical formulae or numerical models.......Prediction of local scour caused by offshore wind turbine foundations using empirical formulae or numerical models....

Offshore wind resource estimation for wind energy

DEFF Research Database (Denmark)

Hasager, Charlotte Bay; Badger, Merete; Mouche, A.

2010-01-01

Satellite remote sensing from active and passive microwave instruments is used to estimate the offshore wind resource in the Northern European Seas in the EU-Norsewind project. The satellite data include 8 years of Envisat ASAR, 10 years of QuikSCAT, and 23 years of SSM/I. The satellite observati......Satellite remote sensing from active and passive microwave instruments is used to estimate the offshore wind resource in the Northern European Seas in the EU-Norsewind project. The satellite data include 8 years of Envisat ASAR, 10 years of QuikSCAT, and 23 years of SSM/I. The satellite...... observations are compared to selected offshore meteorological masts in the Baltic Sea and North Sea. The overall aim of the Norsewind project is a state-of-the-art wind atlas at 100 m height. The satellite winds are all valid at 10 m above sea level. Extrapolation to higher heights is a challenge. Mesoscale...... modeling of the winds at hub height will be compared to data from wind lidars observing at 100 m above sea level. Plans are also to compare mesoscale model results and satellite-based estimates of the offshore wind resource....

Offshore oil: Correctness of perspective

International Nuclear Information System (INIS)

Burns, R.F.

1993-01-01

Except for the Gulf of Mexico, the offshore oil industry has been virtually banned from the US Exclusive Economic Zone for ten years. The oil potential in Alaska's Arctic National Wildlife Refuge (ANWR) is also off limits. The Gulf of Mexico is the only place with prospects for future success and a number of companies both large and small are determined to move forward. The depressed price of oil does not encourage development but recently gas prices in the US have increased, making offshore gas development more feasible. Perhaps most significant is development and application of new technology and more intense management to make sure it works. The offshore oil companies and support industries have made significant technological advances, expending over and above the dollars paid in taxes, lease fees, and royalties. The ocean industries harbor a great reservoir of high technology knowledge. They have demonstrated the ability to successfully meet a vast array of challenges in exploring for, drilling, and producing oil and gas in extreme conditions. These facts beg the question as to the rational basis of each and every regulation and the ban on drilling

Conference on offshore wind energy in France and Germany: challenges of a promising segment

International Nuclear Information System (INIS)

Chrupek, Thierry; Falk, Thorsten; Hofmann, Stefanie; Gouverneur, Philippe; Le Visage, Christophe; Saint Martin, Gro de; Meyerjuergens, Tim; Dachicourt, Pierre-Georges; Hube, Wilfried