WorldWideScience

Sample records for n-rich plasma-polymerized ethylene

  1. Surface modification of poly(ethylene terephthalate) by plasma polymerization of poly(ethylene glycol).

    Science.gov (United States)

    Sakthi Kumar, D; Fujioka, Masayori; Asano, Kentaro; Shoji, Atsumu; Jayakrishnan, Athipettah; Yoshida, Yasuhiko

    2007-09-01

    Poly(ethylene glycol) (PEG) was 'polymerized' onto poly(ethylene terephthalate) (PET) surface by radio frequency (RF) plasma polymerization of PEG (average molecular weight 200 Da) at a monomer vapour partial pressure of 10 Pa. Thin films strongly adherent onto PET could be produced by this method. The modified surface was characterized by infra red (IR) spectroscopy, scanning electron microscopy (SEM), atomic force microscopy (AFM), cross-cut test, contact angle measurements and static platelet adhesion studies. The modified surface, believed to be extensively cross-linked, however showed all the chemical characteristics of PEG. The surface was found to be highly hydrophilic as evidenced by an interfacial free energy of about 0.7 dynes/cm. AFM studies showed that the surface of the modified PET became smooth by the plasma polymerized deposition. Static platelet adhesion studies using platelet rich plasma (PRP) showed considerably reduced adhesion of platelets onto the modified surface by SEM. Plasma 'polymerization' of a polymer such as PEG onto substrates may be a novel and interesting strategy to prepare PEG-like surfaces on a variety of substrates since the technique allows the formation of thin, pin-hole free, strongly adherent films on a variety of substrates.

  2. Pulsed Plasma Polymerization of Perfluorooctyl Ethylene for Transparent Hydrophobic Thin Coatings

    Science.gov (United States)

    Liu, Xiaojun; Wang, Lei; Hao, Jie; Chu, Liqiang

    2015-12-01

    Herein we report on the deposition of transparent hydrophobic thin coatings by radio frequency plasma polymerization (PP) of perfluorooctyl ethylene (PFOE) in both pulsed and continuous wave (CW) modes. The chemical compositions of the resulting PP-PFOE coatings were confirmed by means of Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS). The thicknesses and surface morphologies of the coatings were examined using surface plasmon resonance spectroscopy and atomic force microscopy. The surface wetting properties and optical transmittance were measured using a water contact angle goniometer and UV-vis spectroscopy. The FT-IR and XPS data showed that the PP-PFOE coatings deposited in the pulsed mode had a higher retention of CF2 groups compared to those from the CW mode. While the water contact angle of the freshly deposited PP-PFOE from the pulsed mode showed a decrease from 120 degrees to 111 degrees in the first two days, it then remained almost unchanged up to 45 days. The UV-vis data indicated that a PP-PFOE coating 30.6 nm thick had a light transmittance above 90% in the UV and visible ranges. The deposition rates under various plasma conditions are also discussed. supported by the Tianjin Research Program of Application Foundation and Advanced Technology, China (No. 12JCYBJC31700) and the Program for New Century Excellent Talents in University, China (No. NCET-12-1064)

  3. Blood compatibility of surface modified poly(ethylene terephthalate) (PET) by plasma polymerized acetobromo-alpha-D-glucose.

    Science.gov (United States)

    Kumar, D Sakthi; Nair, Baiju G; Varghese, Saino H; Nair, Remya; Hanajiri, T; Maekawa, T; Yoshida, Yasuhiko; John, Rajan K; Jayakrishnan, A

    2010-02-01

    Poly (ethylene terephthalate) (PET) was surface modified by plasma polymerization of acetobromo-alpha-D-glucose (ABG) at different radio frequency (RF) powers. Plasma polymerization was carried out by vaporizing ABG in the powder form by heating at 135 degrees C. Surface modification resulted in improved hydrophilicity and smoothness of the surface especially at low RF powers (30-50 W), but at high RF powers, the surface was found to be etched and the hydrophilicity decreased as evidenced by atomic force microscopy (AFM) and contact angle measurements. The plasma polymerized ABG film was found to be extensively cross-linked as evidenced by its insolubility in water. Infra red (IR) and X-ray photoelectron spectroscopy (XPS) were employed to characterize the plasma polymerized ABG films. IR studies revealed that at lower RF powers, polymerization was taking place mainly by breaking up of acetoxy group while retaining the ring structures to a major extent during the polymerization process whereas at high RF powers, the rupture of ring structures was indicated. XPS indicated a reduction in the percentage of oxygen in the polymers going from low to high RF powers suggestive of complete destruction of the acetoxy group at high RF powers. Cross-cut tests showed excellent adhesive properties of the plasma polymerized ABG films onto PET. Static platelet adhesion tests using platelet rich human plasma showed significantly reduced adhesion of platelets onto modified PET surface as evidenced by scanning electron microscopy. Polymerization of glucose and its derivatives using RF plasma has not been reported so far and the preliminary results reported in this study shows that this could be an interesting approach in the surface modification of biomaterials.

  4. Plasma polymerization of ethylene in an atmospheric pressure-pulsed discharge

    Science.gov (United States)

    Donohoe, K.; Wydeven, T.

    1979-01-01

    The polymerization of ethylene in an atmospheric pressure-pulsed discharge has been studied. Partial pressures of ethylene up to 4 kN/sq m were used with helium as a diluent. Deposition rates (on glass slides) were the same throughout the discharge volume over a wide range of operating conditions. These rates were in the 1-2 A/sec range. The films were clear, soft, and showed good adhesion to the glass substrates. Oligomers large enough to visibly scatter 637.8-nm light were observed in the gas phase under all conditions in which film deposition occurred. The experimental results suggest that Brownian diffusion of these oligomers was the rate-limiting step in the film deposition process.

  5. Characterization of plasma-polymerized 4-vinyl pyridine with silver nanoparticies on poly(ethylene terephthalate) film for anti-microbial properties

    DEFF Research Database (Denmark)

    Jiang, J.; Winther-Jensen, Bjørn; Kjær, Erik Michael

    2006-01-01

    4-vinyl pyridine was polymerized on poly(ethylene terephthalate) (PET) film by using lower energy pulsed AC plasma under low pressure in Ar atmosphere. The plasma polymerized coating was characterized by ATR Fourier transform infrared (FT-IR), scanning electron microscopy (SEM), field emission...... scanning electron microscopy (FE-SEM), atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). Different thicknesses Of poly(4-vinyl pyridine) coating under different plasma polymerization conditions were studied. Silver nanoparticles with diameter around 50nm deposit were precipitated...... on the poly(4-vinyl pyridine) coating by UV irradiation in Silver nitride water solution, in order to enhance the anti-microbial properties. Different kinds of modified PET films were tested for anti-microbial properties against yeast (Debaryomyces hansenii) by using microbiological analyser mu-4200...

  6. Direct fabrication of nanoscale bio-adhesive patterns by electron beam surface modification of plasma polymerized poly ethylene oxide-like coatings.

    Science.gov (United States)

    Brétagnol, Frédéric; Sirghi, Lucel; Mornet, Stéphane; Sasaki, Takao; Gilliland, Douglas; Colpo, Pascal; Rossi, Francois

    2008-03-26

    In this study we present a method to produce nanostructured surfaces containing bio-adhesive features inside a non bio-adhesive matrix. The strategy is based on the combination of low pressure plasma polymerization and electron beam lithography processes and allows the fabrication of the structured materials in just two steps without using any solvents. In a first step, a thin protein-and-cell-repelling coating (∼10 nm) is obtained by plasma polymerization of Di-glyme. Then, in a second step, the bio-adhesive properties of the layer are tuned by monitoring the concentration of ether bonds of the film by irradiating it locally by different irradiation doses with an electron beam. Time-of-flight secondary ion mass spectroscopy and atomic force microscopy analysis have been used to characterize the produced surfaces. Experiments with a model protein (bovine serum albumin) on the patterned surfaces show preferential adhesion to the irradiated regions, indicating the potential of this simple technique for the development of highly compacted sensitive bio-sensing devices.

  7. Plasma polymerization by Softplasma

    DEFF Research Database (Denmark)

    Jiang, J.; Wu, Zhenning; Benter, Maike

    2008-01-01

    In the late 19th century, the first depositions - known today as plasma polymers, were reported. In the last century, more and more research has been put into plasma polymers. Many different deposition systems have been developed. [1, 2] Shi F. F. broadly classified them into internal electrode......, external electrode, and electrodeless microwave or high frequency reactors. [3] Softplasma™ is an internal electrode plasma setup powered by low frequenc~ gower supply. It was developed in late 90s for surface treatment of silicone rubber. [ ]- 5] It is a low pressure, low electron density, 3D homogenous...... plasma. In this study, we are presenting the surface modification"pf polymers by plasma polymerization using Softplasma™. Softplasma™ can be used for two major types of polymerization: polymerization of vinyl monomers, where plasma acts as initiator; chemical vapour deposition, where plasma acts...

  8. Reverse-osmosis membranes by plasma polymerization

    Science.gov (United States)

    Hollahan, J. R.; Wydeven, T.

    1972-01-01

    Thin allyl amine polymer films were developed using plasma polymerization. Resulting dry composite membranes effectively reject sodium chloride during reverse osmosis. Films are 98% sodium chloride rejective, and 46% urea rejective.

  9. Novel polymer coatings based on plasma polymerized 2-methoxyethyl acrylate

    DEFF Research Database (Denmark)

    Wu, Zhenning; Jiang, Juan; Benter, Maike

    2008-01-01

    plasma system[4]. The system named SoftPlasma™ is equipped with unique three-phase pulsed AC voltage. Low energy plasma polymerization has almost no thermal load for sensitive polymer materials[5]. Plasma polymerized coatings are highly cross-linked, pin-hole free and provide hydrophilic or hydrophobic...... properties[4-6]. We have exploited these possibilities and prepared plasma polymerized 2-methoxyethyl acrylate (PPMEA) coatings on various polymer substrates. The PPMEA coatings were optimized using various plasma polymerization conditions and characterized by X-ray photoelectron spectroscopy......, Fouriertransform infrared spectroscopy, Atomic force spectroscopy and Water contact-angle measurements. The microstructures ofPPMEA coatings with different thicknesses were also studied. For practical applications in mind, the coating stability was tested in different media (air, water, acetone, phosphate...

  10. PLASMA POLYMERIZATION OF ACETYLENE/CO2/H2

    Institute of Scientific and Technical Information of China (English)

    ZHENG Ji; FANG Yuee; SHI Tianyi; SHOHEI INOUE

    1989-01-01

    A study has been made on the plasma polymerization of acetylene/CO2/H2 in a capacitively coupled RF plasma. The monomer mixture yielded a crosslinked film with light brown color. A kinetic study is reported for the plasma polymerization of acetylene/CO2/H2. The effects of discharge power level and reactor geometry on the rate of polymer formation are reported. The structure of the plasma polymer is investigated by IR study.

  11. Charge trapping in plasma-polymerized thin films

    Science.gov (United States)

    Klemberg-Sapieha, J. E.; Sapieha, S.; Wertheimer, M. R.; Yelon, A.

    1980-07-01

    The surface potential of freshly plasma-polymerized films of hexamethyldisiloxane was measured for film thicknesses ranging from about 0.1 to 1 micron. The films are found to be in an electret state under certain fabrication conditions. Experimental evidence is given which indicates that charge trapped during plasma polymerization is uniformly distributed across the sample thickness. It has been found that other electret properties such as the polarity of trapped charge, and the charge retention characteristics can also be controlled by an appropriate choice of polymerization conditions.

  12. Wettability, optical properties and molecular structure of plasma polymerized diethylene glycol dimethyl ether

    Energy Technology Data Exchange (ETDEWEB)

    Azevedo, T C A M; Algatti, M A; Mota, R P; Honda, R Y; Kayama, M E; Kostov, K G; Fernandes, R S [FEG-DFQ-UNESP, Av. Ariberto Pereira da Cunha 333, 12516-410 - Guaratingueta, SP (Brazil); Cruz, N C; Rangel, E C, E-mail: algatti@feg.unesp.b [UNESP, Avenida Tres de Marco, 511, 18087-180 Sorocaba, SP (Brazil)

    2009-05-01

    Modern industry has frequently employed ethylene glycol ethers as monomers in plasma polymerization process to produce different types of coatings. In this work we used a stainless steel plasma reactor to grow thin polymeric films from low pressure RF excited plasma of diethylene glycol dimethyl ether. Plasmas were generated at 5W RF power in the range of 16 Pa to 60 Pa. The molecular structure of plasma polymerized films and their optical properties were analyzed by Fourier Transform Infrared Spectroscopy (FTIR) and Ultraviolet-Visible Spectroscopy, respectively. The IR spectra show C-H stretching at 3000-2900 cm{sup -1}, C=O stretching at 1730-1650 cm{sup -1}, C-H bending at 1440-1380 cm{sup -1}, C-O and C-O-C stretching at 1200-1000 cm{sup -1}. The refraction index was around 1.5 and the optical gap calculated from absorption coefficient presented value near 3.8 eV. Water contact angle of the films ranged from 40 deg. to 35 deg. with corresponding surface energy from 66 to 73x10{sup -7} J. Because of its favorable optical and hydrophilic characteristics these films can be used in ophthalmic industries as glass lenses coatings.

  13. Characterization of Plasma Polymerized Hexamethyldisiloxane Films Prepared by Arc Discharge

    NARCIS (Netherlands)

    Lazauskas, A.; Baltrusaitis, Jonas; Grigaliunas, V.; Jucius, D; Guobiene, A.; Prosycevas, I.; Narmontas, P.

    2014-01-01

    Herein, we present a simple method for fabricating plasma polymerized hexamethyldisiloxane films (pp-HMDSO) possessing superhydrophobic characteristics via arc discharge. The pp-HMDSO films were deposited on a soda–lime–silica float glass using HMDSO monomer vapor as a precursor. A detailed surface

  14. PLASMA POLYMERIZED ORGANOSILANES AS A PROTECTIVE COATING ON METAL

    Institute of Scientific and Technical Information of China (English)

    SUN Qiushi; HOU Xiaohua

    1997-01-01

    Polymer-metal oxane bonds (M-O-Si) can be created in the form of tight networks by silane plasma polymerization directly on the metal (e.g. copper) substrates. In this paper the structure and properties of the plasma-deposited organosilane polymers, the corrosion performance of such coating system on copper substrates were investigated.

  15. PLASMA POLYMERIZATION OF HYDROPHILIC AND HYDROPHOBIC MONOMERS FOR SURFACE MODIFICATION OF NUCLE-MICROPOROUS MEMBRANE

    Institute of Scientific and Technical Information of China (English)

    LI Xuefen; LI Zhifen; CHEN Chuanfu; WU Wenhui

    1990-01-01

    Surface modification of nucle-microporous membrane by plasma polymerization of HEMA, NVP and D4 has been studied. The hydrophilicity of membranes was increased with increasing of plasma polymerization time of hydrophilic monomers HEMA and NVP. The flow rate of water through the membrane was increased remarkably after plasma polymerization of HEMA on it.

  16. Plasma polymerized allylamine coated quartz particles for humic acid removal.

    Science.gov (United States)

    Jarvis, Karyn L; Majewski, Peter

    2012-08-15

    Allylamine plasma polymerization has been used to modify the surface of quartz particles for humic acid removal via an inductively coupled rotating barrel plasma reactor. Plasma polymerized allylamine (ppAA) films were deposited at a power of 25 W, allylamine flow rate of 4.4 sccm and polymerization times of 5-60 min. The influence of polymerization time on surface chemistry was investigated via X-ray photoelectron spectroscopy (XPS), time of flight secondary ion mass spectrometry (ToF-SIMS) and electrokinetic analysis. Acid orange 7 adsorption/desorption quantified the number of surface amine groups. Humic acid removal via ppAA quartz particles was examined by varying pH, removal time, humic acid concentration, and particle mass. Increasing the polymerization time increased the concentration of amine groups on the ppAA quartz surface, thus also increasing the isoelectric point. ToF-SIMS demonstrated uniform distribution of amine groups across the particle surface. Greatest humic acid removal was observed at pH 5 due to electrostatic attraction. At higher pH values, for longer polymerization times, humic acid removal was also observed due to hydrogen bonding. Increasing the initial humic acid concentration increased the mass of humic acid removed, with longer polymerization times exhibiting the greatest increases. Plasma polymerization using a rotating plasma reactor has shown to be a successful method for modifying quartz particles for the removal of humic acid. Further development of the plasma polymerization process and investigation of additional contaminants will aid in the development of a low cost water treatment system.

  17. A plasma polymerization technique to overcome cerebrospinal fluid shunt infections.

    Science.gov (United States)

    Cökeliler, D; Caner, H; Zemek, J; Choukourov, A; Biederman, H; Mutlu, M

    2007-03-01

    Prosthetic devices, mainly shunts, are frequently used for temporary or permanent drainage of cerebrospinal fluid. The pathogenesis of shunt infection is a very important problem in modern medicine and generally this is characterized by staphylococcal adhesion to the cerebrospinal fluid shunt surfaces. In this paper, the prevention of the attachment of test microorganism Staphylococcus epidermidis on the cerebrospinal fluid shunt surfaces by 2-hydroxyethylmethacrylate (HEMA) precursor modification in the plasma polymerization system, is reported. Different plasma polymerization conditions (RF discharge power 10-20-30 W, exposure time 5-10-15 min) were employed during the surface modification. The surface chemistry and topology of unmodified and modified shunts was characterized by x-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and atomic force microscopy (AFM). Also, static contact angle measurements were performed to state the change of surface hydrophilicity. All samples were tested in vitro with Staphylococcus epidermidis. A plasma-polymerized HEMA film (PP HEMA) was found to be an alternative simple method to decrease the microorganism attachment and create bacterial anti-fouling surfaces. The attachment of the model microorganism Staphylococcus epidermidis on the shunt surface modified by PP HEMA at 20 W and 15 min was reduced 62.3% if compared to the unmodified control surface of the shunt.

  18. Antireflection coatings on plastics deposited by plasma polymerization process

    Indian Academy of Sciences (India)

    K M K Srivatsa; M Bera; A Basu; T K Bhattacharya

    2008-08-01

    Antireflection coatings (ARCs) are deposited on the surfaces of optical elements like spectacle lenses to increase light transmission and improve their performance. In the ophthalmic industry, plastic lenses are rapidly displacing glass lenses due to several advantageous features. However, the deposition of ARCs on plastic lenses is a challenging task, because the plastic surface needs treatment for adhesion improvement and surface hardening before depositing the ARC. This surface treatment is usually done in a multi-stage process—exposure to energetic radiations, followed by deposition of a carbonyl hard coating by spin or dip coating processes, UV curing, etc. However, this treatment can also be done by plasma processes. Moreover, the plasma polymerization process allows deposition of optical films at room temperature, essential for plastics. The energetic ions in plasma processes provide similar effects as in ion assisted physical deposition processes to produce hard coatings, without requiring sophisticated ion sources. The plasma polymerization process is more economical than ion-assisted physical vapour deposition processes as regards equipment and source materials and is more cost-effective, enabling the surface treatment and deposition of the ARC in the same deposition system in a single run by varying the system parameters at each step. Since published results of the plasma polymerization processes developed abroad are rather sketchy and the techniques are mostly veiled in commercial secrecy, innovative and indigenous plasma-based techniques have been developed in this work for depositing the complete ARCs on plastic substrates.

  19. A plasma polymerization technique to overcome cerebrospinal fluid shunt infections

    Energy Technology Data Exchange (ETDEWEB)

    Coekeliler, D [Plasma Aided Bioengineering and Biotechnology Research Laboratory, Engineering Faculty, Hacettepe University, 06532, Ankara (Turkey); Caner, H [Department of Neurosurgery, School of Medicine, Baskent University, 06610, Ankara (Turkey); Zemek, J [Institute of Physics, Academy of Sciences of the Czech Republic, Cukrovarnicka 10, 162 53, Prague, Czech Republic (Czech Republic); Choukourov, A [Department of Macromolecular Physics, Charles University, V Holesovickach 2, 18000 Prague (Czech Republic); Biederman, H [Department of Macromolecular Physics, Charles University, V Holesovickach 2, 18000 Prague (Czech Republic); Mutlu, M [Plasma Aided Bioengineering and Biotechnology Research Laboratory, Engineering Faculty, Hacettepe University, 06532, Ankara (Turkey)

    2007-03-01

    Prosthetic devices, mainly shunts, are frequently used for temporary or permanent drainage of cerebrospinal fluid. The pathogenesis of shunt infection is a very important problem in modern medicine and generally this is characterized by staphylococcal adhesion to the cerebrospinal fluid shunt surfaces. In this paper, the prevention of the attachment of test microorganism Staphylococcus epidermidis on the cerebrospinal fluid shunt surfaces by 2-hydroxyethylmethacrylate (HEMA) precursor modification in the plasma polymerization system, is reported. Different plasma polymerization conditions (RF discharge power 10-20-30 W, exposure time 5-10-15 min) were employed during the surface modification. The surface chemistry and topology of unmodified and modified shunts was characterized by x-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and atomic force microscopy (AFM). Also, static contact angle measurements were performed to state the change of surface hydrophilicity. All samples were tested in vitro with Staphylococcus epidermidis. A plasma-polymerized HEMA film (PP HEMA) was found to be an alternative simple method to decrease the microorganism attachment and create bacterial anti-fouling surfaces. The attachment of the model microorganism Staphylococcus epidermidis on the shunt surface modified by PP HEMA at 20 W and 15 min was reduced 62.3% if compared to the unmodified control surface of the shunt.

  20. Nanometer scale vacuum lithography using plasma polymerization and plasma etching

    CERN Document Server

    Kim, S O

    1998-01-01

    Thin films of plasma polymerization were fabricated through plasma polymerization of interelectrode capacitively coupled gas flow system. After delineating the pattern with an accelerating voltage of 30kV, ranging the dose of 1 approx 500 mu C/cm sup 2 , the pattern was developed with a dry type and formed by plasma etching. By analyzing the molecule structure using FT-IR ( Fourier Transform-Infrared Spectrometry), it was confirmed that the thin films of PPMST (Plasma Polymerized Methylmethacrylate+Styrene+Tetramethyltin) contained the functional radicals of the MST (Methylmethacrylate sub S tyrene+Tetramethyltin) monomer. The Thin films of PPMST had a highly cross-linked structure resulting in a higher molecule weight than the conventional resist. The deposition rate of the PPMST thin films was 230 approx 600 A/min as a function of 50 approx 200 W power and 200 approx 60 A/min as a function 0.1 approx 0.7 Torr pressure. The etching rate of the thin films of PPMST was 875 approx 3520 A/min as a function of 50...

  1. Composite plasma polymerized sulfonated polystyrene membrane for PEMFC

    Energy Technology Data Exchange (ETDEWEB)

    Nath, Bhabesh Kumar; Khan, Aziz; Chutia, Joyanti, E-mail: jchutiaiasst@gmail.com

    2015-10-15

    Highlights: • Methyl methane sulfonate (MMS) is used as the sulfonating agent. • The proton conductivity of the membrane is found to be 0.141 S cm{sup −1}. • Power density of fuel cell with styrene/MMS membrane is 0.5 W cm{sup −2}. • The membrane exhibits thermal stability up to 140 °C. - Abstract: This work presents the introduction of an organic compound methyl methane sulfonate (MMS) for the first time in fabrication of polystyrene based proton exchange membrane (PEM) by plasma polymerization process. The membrane is fabricated by co-polymerizing styrene and MMS in capacitively coupled continuous RF plasma. The chemical composition of the plasma polymerized polymer membrane is investigated using Fourier Transform Infrared Spectroscopy which reveals the formation of composite structure of styrene and MMS. The surface morphology studied using AFM and SEM depicts the effect of higher partial pressure of MMS on surface topography of the membrane. The proton transport property of the membrane studied using electrochemical impedance spectroscopy shows the achievement of maximum proton conductivity of 0.141 S cm{sup −1} which is comparable to Nafion 117 membrane. Fuel cell performance test of the synthesized membrane shows a maximum power density of 500 mW cm{sup −2} and current density of 0.62 A cm{sup −2} at 0.6 V.

  2. Plasma polymerized epoxide functional surfaces for DNA probe immobilization.

    Science.gov (United States)

    Chu, Li-Qiang; Knoll, Wolfgang; Förch, Renate

    2008-09-15

    The development of functional surfaces for the immobilization of DNA probe is crucial for a successful design of a DNA sensor. In this report, epoxide functional thin films were achieved simply by pulsed plasma polymerization (PP) of glycidyl methacrylate (GMA) at low duty cycle. The presence of epoxide groups in the resulting ppGMA films was confirmed by Fourier transform infrared spectroscopy. The ppGMA coatings were found to be resistant to the non-specific adsorption of DNA strands, while the epoxide groups obtained could react with amine-modified DNA probes in a mild basic environment without any activation steps. A DNA sensor was made, and was successfully employed to distinguish different DNA sequences with one base pair mismatch as seen by surface plasmon enhanced fluorescence spectroscopy (SPFS). The regeneration of the present DNA sensor was also discussed. This result suggests that surface modification with ppGMA films is very promising for the fabrication of various DNA sensors.

  3. Organic nanocones fabricated by atmospheric plasma polymerization for immobilizing bioprobes

    Energy Technology Data Exchange (ETDEWEB)

    Chen Guangliang; Chen Wenxing [Key Laboratory of Advanced Textile Materials and Manufacturing Technology, Ministry of Education, Zhejiang Sci-Tech University, Hangzhou 310018 (China); Chen Shihua; Zhou Mingyan [Department of Civil and Environmental Engineering, Rensselaer Polytechnic Institute, 110 8th Street, Troy, NY 12180 (United States); Yang Size [Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing 100080 (China)], E-mail: glchen@zstu.edu.cn

    2008-02-20

    Inspired by the formation process of natural thundershowers, we fabricated an organic nanocone matrix-like bamboo-shoot by using atmospheric plasma polymerization in the absence of any catalyst or template. The discharging characteristics affected the nanocone shape and distribution in an obvious way. The nanocones prepared by helium (He) plasma were about 120 nm in diameter and 80 nm high. The nanostructured surface acted as an adhesion layer immobilizing DNA probes for DNA hybridization assay. The density of NH{sub 2}-DNA probes prepared by He, argon (Ar) and nitrogen (N{sub 2}) plasma was confirmed by the dyed oligonucleotide and was found to be 3.2, 1.0 and 0.6 pM cm{sup -2}, respectively. Each nanocone prepared by helium plasma contains nearly 4 x 10{sup 2} amine groups.

  4. Hydrophobic plasma polymerized hexamethyldisilazane thin films: characterization and uses

    Directory of Open Access Journals (Sweden)

    Alexsander Tressino de Carvalho

    2006-03-01

    Full Text Available Hexametildisilazane (HMDS plasma polymerized thin films obtained using low frequency power supplies can be used to make adsorbent films and turn surfaces hydrophobic. The aim of this work was to verify the hydrophobicity and adsorption properties of HMDS thin films (with and without the addition of oxygen, resulting in double or single layer films obtained using an inductive reactor powered with a 13.56 MHz power supply. Single and double layer thin films were deposited on silicon for film characterization, polypropylene (PP for ultraviolet (UVA/UVC resistance tests, piezoelectric quartz crystal for adsorption tests. The double layer (intermixing of HMDS plasma polymerized films and HMDS plasma oxidized surfaces showed a non-continuous layer. The films showed good adhesion to all substrates. Infrared analysis showed the presence of CHn, SiCH3, SiNSi and SiCH2Si within the films. Contact angle measurements with water showed hydrophobic surfaces. UVA/UVC exposure of the films resulted in the presence of cross-linking on carbonic radicals and SiCH2Si formation, which resulted in a possible protection of PP against UVA/UVC for a duration of up to two weeks. Adsorption tests showed that all organic reactants were adsorbed but not water. Plasma etching (PE using O2 showed that even after 15 minutes of exposure the films do not change their hydrophobic characteristic but were oxidized. The results point out that HMDS films can be used: for ultraviolet protection of flexible organic substrates, such as PP, for sensor and/or preconcentrator development, due to their adsorption properties, and in spatial applications due to resistance for O2 attack in hostile conditions, such as plasma etching.

  5. Controlling the Plasma-Polymerization Process of N-Vinyl-2-pyrrolidone

    DEFF Research Database (Denmark)

    Norrman, Kion; Winther-Jensen, Bjørn

    2005-01-01

    N-vinyl-2-pyrrolidone was plasma-polymerized on glass substrates using a pulsed AC plasma. Pulsed AC plasma produces a chemical surface structure different from that produced by conventional RF plasma; this is ascribed to the different power regimes used. A high degree of control over the structure...... of the chemical surface was obtained using pulsed AC plasma, as shown by ToF-SIMS. It is demonstrated how the experimental conditions to some extent control the chemical structure of the plasma-polymerized film, e.g., film thickness, density of post-plasma-polymerized oligomeric chains, and the density of intact...

  6. Micro patterning of cell and protein non-adhesive plasma polymerized coatings for biochip applications

    DEFF Research Database (Denmark)

    Bouaidat, Salim; Berendsen, C.; Thomsen, P.;

    2004-01-01

    Micro scale patterning of bioactive surfaces is desirable for numerous biochip applications. Polyethyleneoxide-like (PEO-like) coating with non-fouling functionality has been deposited using low frequency AC plasma polymerization. The non-fouling properties of the coating were tested with human...... cells ( HeLa) and fluorescence labeled proteins (isothiocyanate-labeled bovine serum albumin, i.e. FITC-BSA). The PEO-like coatings were fabricated by plasma polymerization of 12-crown-4 (ppCrown) with plasma polymerized hexene (ppHexene) as adhesion layer. The coatings were micro patterned using...

  7. Characterization of Plasma-Polymerized Fused Polycyclic Compounds for Binding Conducting Polymers

    DEFF Research Database (Denmark)

    Winther-Jensen, Bjørn; Norrman, Kion; Kingshott, Peter

    2005-01-01

    An investigation is made of the plasma polymerization of fused polycyclic monomers containing a dioxy-ring that is fused to an aromatic ring. These molecules provide the basis for very efficient polymerization mechanisms in which only the dioxy-ring undergoes ring opening during the polymerization...... with the remaining part of the monomer remaining intact. XPS, ToF-SIMS, and IR are used to investigate the chemistry of the films produced by plasma polymerization of EDT, which contains a high content of the aromatic group. We find that the plasma-polymerized films of EDT contain intact thiophene groups...

  8. Surface modification of nanoporous alumina membranes by plasma polymerization.

    Science.gov (United States)

    Losic, Dusan; Cole, Martin A; Dollmann, Björn; Vasilev, Krasimir; Griesser, Hans J

    2008-06-18

    The deposition of plasma polymer coatings onto porous alumina (PA) membranes was investigated with the aim of adjusting the surface chemistry and the pore size of the membranes. PA membranes from commercial sources with a range of pore diameters (20, 100 and 200 nm) were used and modified by plasma polymerization using n-heptylamine (HA) monomer, which resulted in a chemically reactive polymer surface with amino groups. Heptylamine plasma polymer (HAPP) layers with a thickness less than the pore diameter do not span the pores but reduce their diameter. Accordingly, by adjusting the deposition time and thus the thickness of the plasma polymer coating, it is feasible to produce any desired pore diameter. The structural and chemical properties of modified membranes were studied by scanning electron microscopy (SEM), atomic force microscopy (AFM) and x-ray electron spectroscopy (XPS). The resultant PA membranes with specific surface chemistry and controlled pore size are applicable for molecular separation, cell culture, bioreactors, biosensing, drug delivery, and engineering complex composite membranes.

  9. Plasma-polymerized thiophene films for enhanced rubber steel bonding

    Science.gov (United States)

    Delattre, James L.; d'Agostino, Riccardo; Fracassi, Francesco

    2006-03-01

    Thin films of plasma-polymerized thiophene (PPTh) were deposited on cold-rolled steel substrates to improve adhesion to rubber compounds. PPTh films were characterized by X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy (FT-IR) and atomic force microscopy. The ratio of carbon-to-sulfur found in PPTh films is 4:1, suggesting the monomer structure is generally intact, which was supported by FT-IR absorptions characteristic of polymerized thiophene rings. However, some fragmentation did occur to give acetylenic and aliphatic groups. Steel-rubber adhesion measurements, performed in accordance with the ASTM 429-B peel test, strongly depended on cleaning and pretreatment methods as well as film thickness. Best results were obtained on polished steel samples that were cleaned with acid, pretreated with a hydrogen/argon plasma, then coated with 50 Å of PPTh film. These samples exhibited a peel force of 14.3 N/mm, which is comparable to that of polished brass control samples. Depth-profiling XPS analysis of the rubber-steel interface showed the existence of an iron sulfide layer which is likely responsible for the strong adhesion.

  10. Initial biocompatibility of plasma polymerized hexamethyldisiloxane films with different wettability

    Energy Technology Data Exchange (ETDEWEB)

    Krasteva, N A; Toromanov, G; Hristova, K T; Radeva, E I; Pecheva, E V; Dimitrova, R P; Altankov, G P; Pramatarova, L D, E-mail: nataly@bio21.bas.b

    2010-11-01

    Understanding the relationships between material surface properties, behaviour of adsorbed proteins and cellular responses is essential to design optimal material surfaces for tissue engineering. In this study we modify thin layers of plasma polymerized hexamethyldisiloxane (PPHMDS) by ammonia treatment in order to increase surface wettability and the corresponding biological response. The physico-chemical properties of the polymer films were characterized by contact angle (CA) measurements and Fourier Transform Infrared Spectroscopy (FTIR) analysis.Human umbilical vein endothelial cells (HUVEC) were used as model system for the initial biocompatibility studies following their behavior upon preadsorption of polymer films with three adhesive proteins: fibronectin (FN), fibrinogen (FG) and vitronectin (VN). Adhesive interaction of HUVEC was evaluated after 2 hours by analyzing the overall cell morphology, and the organization of focal adhesion contacts and actin cytoskeleton. We have found similar good cellular response on FN and FG coated polymer films, with better pronounced vinculin expression on FN samples while. Conversely, on VN coated surfaces the wettability influenced significantly initial celular interaction spreading. The results obtained suggested that ammonia plasma treatment can modulate the biological activity of the adsorbed protein s on PPHMDS surfaces and thus to influence the interaction with endothelial cells.

  11. Decreased Bacterial Attachment and Protein Adsorption to Coatings Produced by Low Enegy Plasma Polymerization

    DEFF Research Database (Denmark)

    Andersen, T.E.; Kingshott, Peter; Benter, M.

    with a surface less prone to the adsorption of biological matter. In the current study two different hydrophilic nanoscale coatings were produced by low energy plasma polymerization [3] and investigated· f()rl()w ... pr()tein adsorption and bacterial attachment properties. Methods were setup to enable...... and Methods: Coatings: Plasma polymerized poly(vinyl pyrrolidone) (PP-PVP), poly(2-methoxyethyl methacrylate) (PPPMEA) or an inorganic oxide (10) coating were applied onto medical grade silicon rubber sheets (Silopren LSR 2050, Momentive Performance Materials Inc.). Plasma polymerization chamber......-coated crystals were then treated with one of the plasma polymerized coatings. Adsorption of fibrinogen, human serum albumin or immunoglobulin G was measured using a QCM-D instrument [5] (model E4, Q-Sense AB, Vastra Frolunda, Sweden) using a solution of 50llg/1 protein in PBS buffer. Results and Discussion: Our...

  12. Surface modification by plasma polymerization: film deposition, tailoring of surface properties and biocompatibility

    OpenAIRE

    Os, van, J.

    2000-01-01

    The work described in this thesis concerns the surface modification of materials by thin film deposition in a plasma reactor. In particular, thin polymeric films bearing amine functionalities were synthesized by plasma polymerization of amino group containing monomers. In addition to the synthesis, attention was directed towards the characterization of these films, and the tailoring of their surface properties on a molecular level. Finally, the amino groups introduced by plasma polymerization...

  13. Comparative studies of chemically synthesized and RF plasma-polymerized poly(-toluidine)

    Indian Academy of Sciences (India)

    Shama Islam; G B V S Lakshmi; M Zulfequar; M Husain; Azher M Siddiqui

    2015-04-01

    Poly(-toluidine) (POT) polymer was synthesized by chemical method and RF plasma polymerization at a radio frequency (RF) power input of 15 W on ultrasonically cleaned glass and silicon wafer substrates. These samples were characterized by DC conductivity measurements, UV–visible, XRD and FTIR techniques. The DC-conductivity was measured at 410 K, which was found to increase by two orders of magnitude for thin film as compared to pellet samples. It has been observed that the activation energy increases for RF plasma-polymerized POT. Transmission and reflectance spectra were studied for measuring optical constants like absorption coefficient (), extinction coefficient (), optical band gap (g), Urbach energy (e), and refractive index (). From XRD studies, one can infer that the samples grown by both the methods are amorphous in nature. The results indicate that the structures of plasma-polymerized POT are rather different from polymers synthesized by conventional chemical methods, due to a higher degree of cross-linking and branching reactions in plasma polymerization. This makes them suitable for various electroactive devices. A higher and more stable conductivity can be obtained with RF plasma-polymerized POT which is much smoother and more uniform.

  14. Cold-atmospheric pressure plasma polymerization of acetylene on wood flour for improved wood plastics composites

    Science.gov (United States)

    Lekobou, William; Pedrow, Patrick; Englund, Karl; Laborie, Marie-Pierre

    2009-10-01

    Plastic composites have become a large class of construction material for exterior applications. One of the main disadvantages of wood plastic composites resides in the weak adhesion between the polar and hydrophilic surface of wood and the non-polar and hydrophobic polyolefin matrix, hindering the dispersion of the flour in the polymer matrix. To improve interfacial compatibility wood flour can be pretreated with environmentally friendly methods such as cold-atmospheric pressure plasma. The objective of this work is therefore to evaluate the potential of plasma polymerization of acetylene on wood flour to improve the compatibility with polyolefins. This presentation will describe the reactor design used to modify wood flour using acetylene plasma polymerization. The optimum conditions for plasma polymerization on wood particles will also be presented. Finally preliminary results on the wood flour surface properties and use in wood plastic composites will be discussed.

  15. TFE-PLASMA POLYMERIZED DERMAL SHEEP COLLAGEN FOR THE REPAIR OF ABDOMINAL-WALL DEFECTS

    NARCIS (Netherlands)

    VANDERLAAN, JS; LOPEZ, GP; VANWACHEM, PB; NIEUWENHUIS, P; RATNER, BD; BLEICHRODT, RP; SCHAKENRAAD, JM

    1991-01-01

    The aim of this study was to design and evaluate a degradable biomaterial for the repair of abdominal wall defects. Hexamethylenediisocyanate-tanned dermal sheep collagen (HDSC) was plasma-polymerized with tetrafluoroethylene (TFE) which resulted in a hydrophobic surface on the visceral side (TFE-HD

  16. Surface modification by allylamine plasma polymerization promotes osteogenic differentiation of human adipose-derived stem cells.

    Science.gov (United States)

    Liu, Xujie; Feng, Qingling; Bachhuka, Akash; Vasilev, Krasimir

    2014-06-25

    Tuning the material properties in order to control the cellular behavior is an important issue in tissue engineering. It is now well-established that the surface chemistry can affect cell adhesion, proliferation, and differentiation. In this study, plasma polymerization, which is an appealing method for surface modification, was employed to generate surfaces with different chemical compositions. Allylamine (AAm), acrylic acid (AAc), 1,7-octadiene (OD), and ethanol (ET) were used as precursors for plasma polymerization in order to generate thin films rich in amine (-NH2), carboxyl (-COOH), methyl (-CH3), and hydroxyl (-OH) functional groups, respectively. The surface chemistry was characterized by X-ray photoelectron spectroscopy (XPS), the wettability was determined by measuring the water contact angles (WCA) and the surface topography was imaged by atomic force microscopy (AFM). The effects of surface chemical compositions on the behavior of human adipose-derive stem cells (hASCs) were evaluated in vitro: Cell Count Kit-8 (CCK-8) analysis for cell proliferation, F-actin staining for cell morphology, alkaline phosphatase (ALP) activity analysis, and Alizarin Red S staining for osteogenic differentiation. The results show that AAm-based plasma-polymerized coatings can promote the attachment, spreading, and, in turn, proliferation of hASCs, as well as promote the osteogenic differentiation of hASCs, suggesting that plasma polymerization is an appealing method for the surface modification of scaffolds used in bone tissue engineering.

  17. Plasma Polymerization Surface Modification of Carbon Black and its Effect in Elastomers

    NARCIS (Netherlands)

    Mathew, T.; Datta, R.N.; Dierkes, W.K.; Talma, A.G.; Ooij, van W.J.; Noordermeer, J.W.M.

    2011-01-01

    Surface modification of carbon black by plasma polymerization was aimed to reduce its surface energy in order to compatibilize the filler with various elastomers. A fullerenic carbon black was used for the modification process. Thermogravimetric analysis, wetting behavior with liquids of known surfa

  18. Surface modification by plasma polymerization: film deposition, tailoring of surface properties and biocompatibility

    NARCIS (Netherlands)

    Os, van Menno Thomas

    2000-01-01

    The work described in this thesis concerns the surface modification of materials by thin film deposition in a plasma reactor. In particular, thin polymeric films bearing amine functionalities were synthesized by plasma polymerization of amino group containing monomers. In addition to the synthesis,

  19. Immobilization and controlled release of drug using plasma polymerized thin film

    Energy Technology Data Exchange (ETDEWEB)

    Myung, Sung-Woon [Department of Dental Materials, School of Dentistry, MRC Center, Chosun University, 309 Pilmun-daero, Dong-gu, Gwangju (Korea, Republic of); Jung, Sang-Chul [Department of Environmental Engineering, Sunchon National University, Sunchon 540-742 (Korea, Republic of); Kim, Byung-Hoon, E-mail: kim5055@chosun.ac.kr [Department of Dental Materials, School of Dentistry, MRC Center, Chosun University, 309 Pilmun-daero, Dong-gu, Gwangju (Korea, Republic of)

    2015-06-01

    In this study, plasma polymerization of acrylic acid was employed to immobilize drug and control its release. Doxorubicin (DOX) was immobilized covalently on the glass surface deposited with plasma polymerized acrylic acid (PPAAc) thin film containing the carboxylic group. At first, the PPAAc thin film was coated on a glass surface at a pressure of 1.33 Pa and radio frequency (RF) discharge power of 20 W for 10 min. DOX was immobilized on the PPAAc deposition in a two environment of phosphate buffer saline (PBS) and dimethyl sulfoxide (DMSO) solutions. The DOX immobilized surface was characterized by scanning electron microscope, atomic force microscope and attenuated total reflection Fourier transform infrared spectroscopy. The DOX molecules were more immobilized in PBS than DMSO solution. The different immobilization and release profiles of DOX result from the solubility of hydrophobic DOX in aqueous and organic solutions. Second, in order to control the release of the drug, PPAAc thin film was covered over DOX dispersed layer. Different thicknesses and cross-linked PPAAc thin films by adjusting deposition time and RF discharge power were covered on the DOX layer dispersed. PPAAc thin film coated DOX layer reduced the release rate of DOX. The thickness control of plasma deposition allows controlling the release rate of drug. - Highlights: • Doxorubicin was immobilized on the surface of plasma polymerized acrylic acid thin film. • Release profile of doxorubicin was affected by aqueous and organic solutions. • Plasma polymerized acrylic acid thin film can be used to achieve controlled release.

  20. Sulfonated polystyrene-type plasma-polymerized membranes for miniature direct methanol fuel cells

    Science.gov (United States)

    Roualdes, Stéphanie; Topala, Ionut; Mahdjoub, Habiba; Rouessac, Vincent; Sistat, Philippe; Durand, Jean

    Sulfonated polystyrene-type membranes were synthesized by plasma polymerization of a mixture of styrene and trifluoromethane sulfonic acid monomers in a low-frequency after-glow discharge plasma reactor. Such a deposition process enables the preservation of the monomers structure, which was confirmed by mass spectrometry analysis. The synthesized plasma-polymerized membranes are dense and uniform with a few microns thickness. Their structure determined by Fourier-transform infra-red spectroscopy and X-ray photoelectron spectroscopy is very rich in sulfonic acid groups (up to 5%) and stable up to 120 °C. Even if their intrinsic proton conductivity is low (10 -1 mS cm -1), directly related to their disorganized and highly cross-linked structure, plasma-polymerized membranes present a proton conduction ability similar to Nafion ® because of their low thickness. Due to their highly cross-linked structure, these membranes enable a reduction of the methanol crossover in a factor 10 by comparison with Nafion ®. Thus, the integration of plasma-polymerized films in miniaturized direct methanol fuel cells as proton-exchange membranes seems promising.

  1. Modification of surface properties of bell metal by radiofrequency plasma polymerization

    Science.gov (United States)

    Chutia, Joyanti; Choudhury, Arup Jyoti; Pal, Arup Ratan; Gogoi, Dolly

    2012-11-01

    Radiofrequency (RF) plasma polymerization is a convenient thin film deposition process as it facilitates the synthesis of polymer films with stable physico-chemical properties suitable for various applications in microelectronic, optical, and biomedical fields. The unique properties of these plasma polymerized films as compared to the conventional ones are strongly related to the proper adjustment of the external plasma discharge parameters and selection of suitable monomer. It is also important to study the fundamental chemistry of RF plasma polymerization process, so that one can successfully correlate the internal features of the discharge with the film properties and explore their possible technological applications. The possibility of using styrene-based plasma polymer (SPP) films on bell metal as protective coatings is explored in this work. Depositions of the films are carried out in RF Ar/styrene discharge at working pressure of 1.2 × 10-1 mbar and at the RF power range of 20 to 110 W. Optical emission spectroscopy (OES) is used to study the active species generated during plasma polymerization, while Fourier transform infrared (FT-IR) and X-ray photoelectron spectroscopy (XPS) are used to analyze the internal chemical structures of the films. The protective performances of the SPP films are attempted to correlate with the results obtained from OES, FT-IR, and XPS analyses.

  2. Enhancement of Fluorescence-Based Sandwich Immunoassay Using Multilayered Microplates Modified with Plasma-Polymerized Films

    Directory of Open Access Journals (Sweden)

    Kazuyoshi Yano

    2016-12-01

    Full Text Available A functional modification of the surface of a 96-well microplate coupled with a thin layer deposition technique is demonstrated for enhanced fluorescence-based sandwich immunoassays. The plasma polymerization technique enabling the deposition of organic thin films was employed for the modification of the well surface of a microplate. A silver layer and a plasma-polymerized film were consecutively deposited on the microplate as a metal mirror and the optical interference layer, respectively. When Cy3-labeled antibody was applied to the wells of the resulting multilayered microplate without any immobilization step, greatly enhanced fluorescence was observed compared with that obtained with the unmodified one. The same effect could be also exhibited for an immunoassay targeting antigen directly adsorbed on the multilayered microplate. Furthermore, a sandwich immunoassay for the detection of interleukin 2 (IL-2 was performed with the multilayered microplates, resulting in specific and 88-fold–enhanced fluorescence detection.

  3. Enhancement of proton conductivity of sulfonated polystyrene membrane prepared by plasma polymerization process

    Indian Academy of Sciences (India)

    Bhabesh Kumar Nath; Aziz Khan; Joyanti Chutia; Arup Ratan Pal; Heremba Bailung; Neelotpal Sen Sarma; Devasish Chowdhury; Nirab Chandra Adhikary

    2014-12-01

    This work reports the achievement of higher proton conductivity of polystyrene based proton exchange membrane synthesized in a continuous RF plasma polymerization process using two precursors, styrene (C8H8) and trifluoromethane sulfonic acid (CF3SO3H). The chemical composition of the developed membranes is investigated using Fourier transform infrared spectroscopy and energy dispersive spectroscopy. Scanning electron microscopy has been used for the study of surface morphology and thickness measurement of the membrane. The membranes deposited in the power range from 0.114 to 0.318 Wcm-2 exhibit a lot of variation in the properties like proton transport, water uptake, sulfonation rate, ion exchange capacity and thermal behaviour. The proton conductivity of the membranes is achieved up to 0.6 Scm-1, measured with the help of potentiostat/galvanostat. The thermogravimetric study of the plasma polymerized membrane shows the thermal stability up to 140 °C temperature.

  4. Surface Modification of Carbon Nanofibers and Graphene Platelets Mixtures by Plasma Polymerization of Propylene

    Directory of Open Access Journals (Sweden)

    Carlos Andrés Covarrubias-Gordillo

    2017-01-01

    Full Text Available Carbon nanofibers (CNFs, graphene platelets (GPs, and their mixtures were treated by plasma polymerization of propylene. The carbon nanoparticles (CNPs were previously sonicated in order to deagglomerate and increase the surface area. Untreated and plasma treated CNPs were analyzed by dynamic light scattering (DLS, transmission electron microscopy (TEM, Fourier transform infrared spectroscopy (FTIR, Raman spectroscopy, and thermogravimetric analysis (TGA. DLS analysis showed a significant reduction of average particle size, due to the sonication pretreatment. Plasma polymerized propylene was deposited on the CNPs surface; the total amount of polymerized propylene was from 4.68 to 6.58 wt-%. Raman spectroscopy indicates an increase in the sp3 hybridization of the treated samples, which suggest that the polymerized propylene is grafted onto the CNPs.

  5. Modulation of release kinetics by plasma polymerization of ampicillin-loaded β-TCP ceramics

    Science.gov (United States)

    Labay, C.; Buxadera-Palomero, J.; Avilés, M.; Canal, C.; Ginebra, M. P.

    2016-08-01

    Beta-tricalcium phosphate (β-TCP) bioceramics are employed in bone repair surgery. Their local implantation in bone defects puts them in the limelight as potential materials for local drug delivery. However, obtaining suitable release patterns fitting the required therapeutics is a challenge. Here, plasma polymerization of ampicillin-loaded β-TCP is studied for the design of a novel antibiotic delivery system. Polyethylene glycol-like (PEG-like) coating of β-TCP by low pressure plasma polymerization was performed using diglyme as precursor, and nanometric PEG-like layers were obtained by simple and double plasma polymerization processes. A significant increase in hydrophobicity, and the presence of plasma polymer was visible on the surface by SEM and quantified by XPS. As a main consequence of the plasma polymerisation, the release kinetics were successfully modified, avoiding burst release, and slowing down the initial rate of release leading to a 4.5 h delay in reaching the same antibiotic release percentage, whilst conservation of the activity of the antibiotic was simultaneously maintained. Thus, plasma polymerisation on the surface of bioceramics may be a good strategy to design controlled drug delivery matrices for local bone therapies.

  6. Application of plasma-polymerized films for isoelectric focusing of proteins in a capillary electrophoresis chip.

    Science.gov (United States)

    Tsai, Shuo-Wen; Loughran, Michael; Hiratsuka, Atsunori; Yano, Kazuyoshi; Karube, Isao

    2003-03-01

    The first use of plasma polymerization technique to modify the surface of a glass chip for capillary isoelectric focusing (cIEF) of different proteins is reported. The electrophoresis separation channel was machined in Tempax glass chips with length 70 mm, 300 microm width and 100 microm depth. Acetonitrile and hexamethyldisiloxane monomers were used for plasma polymerization. In each case 100 nm plasma polymer films were coated onto the chip surface to reduce protein wall adsorption and minimize the electroosmotic flow. Applied voltages of 1000 V, 2000 V and 3000 V were used to separate mixtures of cytochrome c (pI 9.6), hemoglobin (pI 7.0) and phycocyanin (pI 4.65). Reproducible isoelectric focusing of each pI marker protein was observed in different coated capillaries at increasing concentration 2.22-5 microg microL(-1). Modification of the glass capillary with hydrophobic HMDS plasma polymerized films enabled rapid cIEF within 3 min. The separation efficiency of cytochrome c and phycocyanin in both acrylamide and HMDS coated capillaries corresponded to a plate number of 19600 which compares favourably with capillary electrophoresis of neurotransmitters with amperometric detection.

  7. Amine Enrichment of Thin-Film Composite Membranes via Low Pressure Plasma Polymerization for Antimicrobial Adhesion.

    Science.gov (United States)

    Reis, Rackel; Dumée, Ludovic F; He, Li; She, Fenghua; Orbell, John D; Winther-Jensen, Bjorn; Duke, Mikel C

    2015-07-15

    Thin-film composite membranes, primarily based on poly(amide) (PA) semipermeable materials, are nowadays the dominant technology used in pressure driven water desalination systems. Despite offering superior water permeation and salt selectivity, their surface properties, such as their charge and roughness, cannot be extensively tuned due to the intrinsic fabrication process of the membranes by interfacial polymerization. The alteration of these properties would lead to a better control of the materials surface zeta potential, which is critical to finely tune selectivity and enhance the membrane materials stability when exposed to complex industrial waste streams. Low pressure plasma was employed to introduce amine functionalities onto the PA surface of commercially available thin-film composite (TFC) membranes. Morphological changes after plasma polymerization were analyzed by SEM and AFM, and average surface roughness decreased by 29%. Amine enrichment provided isoelectric point changes from pH 3.7 to 5.2 for 5 to 15 min of plasma polymerization time. Synchrotron FTIR mappings of the amine-modified surface indicated the addition of a discrete 60 nm film to the PA layer. Furthermore, metal affinity was confirmed by the enhanced binding of silver to the modified surface, supported by an increased antimicrobial functionality with demonstrable elimination of E. coli growth. Essential salt rejection was shown minimally compromised for faster polymerization processes. Plasma polymerization is therefore a viable route to producing functional amine enriched thin-film composite PA membrane surfaces.

  8. Atmospheric pressure plasma polymerization using double grounded electrodes with He/Ar mixture

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Dong Ha; Kim, Hyun-Jin; Park, Choon-Sang; Tae, Heung-Sik, E-mail: hstae@ee.knu.ac.kr [School of Electronics Engineering, College of IT Engineering, Kyungpook National University, Daegu, 702-701 (Korea, Republic of); Shin, Bhum Jae [Department of Electronics Engineering, Sejong University, Seoul 143-747 (Korea, Republic of); Seo, Jeong Hyun [Department of Electronics Engineering, Incheon National University, Incheon 406-772 (Korea, Republic of)

    2015-09-15

    In this study, we have proposed the double grounded atmospheric pressure plasma jet (2G-APPJ) device to individually control the plasmas in both fragmentation (or active) and recombination (or passive) regions with a mixture of He and Ar gases to deposit organic thin films on glass or Si substrates. Plasma polymerization of acetone has been successfully deposited using a highly energetic and high-density 2G-APPJ and confirmed by scanning electron microscopy (SEM). Plasma composition was measured by optical emission spectroscopy (OES). In addition to a large number of Ar and He spectra lines, we observed some spectra of C{sub 2} and CH species for fragmentation and N{sub 2} (second positive band) species for recombination. The experimental results confirm that the Ar gas is identified as a key factor for facilitating fragmentation of acetone, whereas the He gas helps the plume of plasma reach the substrate on the 2{sup nd} grounded electrode during the plasma polymerization process. The high quality plasma polymerized thin films and nanoparticles can be obtained by the proposed 2G-APPJ device using dual gases.

  9. Atmospheric pressure plasma polymerization using double grounded electrodes with He/Ar mixture

    Directory of Open Access Journals (Sweden)

    Dong Ha Kim

    2015-09-01

    Full Text Available In this study, we have proposed the double grounded atmospheric pressure plasma jet (2G-APPJ device to individually control the plasmas in both fragmentation (or active and recombination (or passive regions with a mixture of He and Ar gases to deposit organic thin films on glass or Si substrates. Plasma polymerization of acetone has been successfully deposited using a highly energetic and high-density 2G-APPJ and confirmed by scanning electron microscopy (SEM. Plasma composition was measured by optical emission spectroscopy (OES. In addition to a large number of Ar and He spectra lines, we observed some spectra of C2 and CH species for fragmentation and N2 (second positive band species for recombination. The experimental results confirm that the Ar gas is identified as a key factor for facilitating fragmentation of acetone, whereas the He gas helps the plume of plasma reach the substrate on the 2nd grounded electrode during the plasma polymerization process. The high quality plasma polymerized thin films and nanoparticles can be obtained by the proposed 2G-APPJ device using dual gases.

  10. High-Voltage Insulation Organic-Inorganic Nanocomposites by Plasma Polymerization

    Directory of Open Access Journals (Sweden)

    Wei Yan

    2014-01-01

    Full Text Available In organic-inorganic nanocomposites, interfacial regions are primarily influenced by the dispersion uniformity of nanoparticles and the strength of interfacial bonds between the nanoparticles and the polymer matrix. The insulating performance of organic-inorganic dielectric nanocomposites is highly influenced by the characteristics of interfacial regions. In this study, we prepare polyethylene oxide (PEO-like functional layers on silica nanoparticles through plasma polymerization. Epoxy resin/silica nanocomposites are subsequently synthesized with these plasma-polymerized nanoparticles. It is found that plasma at a low power (i.e., 10 W can significantly increase the concentration of C–O bonds on the surface of silica nanoparticles. This plasma polymerized thin layer can not only improve the dispersion uniformity by increasing the hydrophilicity of the nanoparticles, but also provide anchoring sites to enable the formation of covalent bonds between the organic and inorganic phases. Furthermore, electrical tests reveal improved electrical treeing resistance and decreased dielectric constant of the synthesized nanocomposites, while the dielectric loss of the nanocomposites remains unchanged as compared to the pure epoxy resin.

  11. Stable modification of PDMS surface properties by plasma polymerization: application to the formation of double emulsions in microfluidic systems.

    Science.gov (United States)

    Barbier, Valessa; Tatoulian, Michaël; Li, Hong; Arefi-Khonsari, Farzaneh; Ajdari, Armand; Tabeling, Patrick

    2006-06-06

    We describe a method based on plasma polymerization for the modification and control of the surface properties of poly(dimethylsiloxane) (PDMS) surfaces. By depositing plasma polymerized acrylic acid coatings on PDMS, we succeeded to fabricate stable (several days) hydrophilic and patterned hydrophobic/hydrophilic surfaces. We used this approach to generate direct and (for the first time in this material) double emulsions in PDMS microchannels.

  12. Comparative study of structural and optical properties of pulsed and RF plasma polymerized aniline films

    Energy Technology Data Exchange (ETDEWEB)

    Barman, Tapan; Pal, Arup R., E-mail: arpal@iasst.gov.in; Chutia, Joyanti

    2014-09-15

    Graphical abstract: - Highlights: • Pulse DC and RF plasma is used for synthesis of conducting polymer films. • Conjugated structure retention is better at optimum powers in both the processes. • Conjugated structure retention is better in case of RF plasma prepared films. • Band gap is lower in case of RF plasma prepared films at higher power. • Defect in pulse plasma prepared film is less than RF plasma prepared thin films. - Abstract: Plasma polymerization of aniline is carried out by means of continuous RF and pulsed DC glow discharge plasma in a common reactor at different applied powers. The discharge control variables are optimized for good quality film growth and the role of fragmentation of the molecular structure on the structural, optical, morphological and optophysical properties of the deposited plasma polymerized aniline (PPAni) layers is investigated. Retention of the conjugated structure is found to be prominent at optimum applied power to the plasma in both the continuous RF and pulsed DC polymerization techniques. Improvement in conjugated structure and chain length have been observed in both the continuous RF and pulse DC PPAni thin films with the increase in applied power to the plasma up to a certain limit of applied power when working pressure is fixed at 0.15 mbar. A decrease in optical bandgap with the increase in applied power to the plasma is observed in both the pulsed DC and RF PPAni thin films, but it is more significant in case of RF PPAni films. The plasma polymerized aniline thin films are found to emit photoluminescence due to band to band transition and defects generated in the structure.

  13. Preparation and properties of plasma-polymerized thiophene (PPT) conducting films

    Energy Technology Data Exchange (ETDEWEB)

    Sadhir, R.K. (Westinghouse Science and Tech. Center, Pittsburgh, PA (United States)); Schoch, K.F. Jr. (Westinghouse Science and Tech. Center, Pittsburgh, PA (United States))

    1993-01-15

    This paper presents, for the first time, conducting films of polythiophene prepared by plasma-polymerization. In this technique, ionized argon is the initiating species for the polymerization of thiophene in a region away from the high RF flux-density. These films displayed a conductivity of 1.8 x 10[sup -4] S cm[sup -1] after doping with iodine. The surface morphology of the films deposited away from the high RF flux-density region showed topology similar to the films prepared by electrochemical methods. The films deposited near the high RF flux-density region showed a platelet structure. (orig.)

  14. Synthesis of PPy-like Nanocrystallines by Oriented Plasma Polymerization at Atmospheric Pressure

    Institute of Scientific and Technical Information of China (English)

    FANG Xin-sheng; GUO Ying; XU Jin-zhou; ZHANG Jing

    2006-01-01

    Polymeric polypyrrole-like (PPy-like) nanocrystallines were fast synthesized through oriented plasma polymerization at atmospheric pressure and room temperature. The effects of discharge power on the nanocrystalline morphology were investigated. Larger power tends to produce longer nanocrystallines. 3 mm long nanowires were produced at the largest power in our experiment. TEM image and the sharp electronic diffraction spots in SAD suggest that the nanoparticles have a single crystal phase. The chemical structure of the nanocrystalline has been studied through FTIR, EDX etc. This novel polymerization method could have great applications in fabricating functional polymeric nanocrystallines.

  15. Hydrophobic coating of solid materials by plasma-polymerized thin film using tetrafluoroethylene

    Science.gov (United States)

    Hozumi, K.; Kitamura, K.; Kitade, T.

    1980-01-01

    Glass slides were coated with plasma-polymerized tetrafluoroethylene films of different thickness using the glow discharge technique in a tube-shaped chamber, and the plasma conditions, film growth rates, light permeability of the polymer films, and particle bond strength in the polymer films were studied. Ashed sections of mouse organs and ashed bacillus spores were also coated to give them hydrophobic treatment without damaging their shapes or appearance. The hydrophobic coating of the specimens was successful, and the fine ash patterns were strongly fixed onto the glass slides, making permanent preparations.

  16. Investigation of the Effect of Plasma Polymerized Siloxane Coating for Enzyme Immobilization and Microfluidic Device Conception

    Directory of Open Access Journals (Sweden)

    Kalim Belhacene

    2016-12-01

    Full Text Available This paper describes the impact of a physical immobilization methodology, using plasma polymerized 1,1,3,3, tetramethyldisiloxane, on the catalytic performance of β-galactosidase from Aspergillus oryzae in a microfluidic device. The β-galactosidase was immobilized by a polymer coating grown by Plasma Enhanced Chemical Vapor Deposition (PEVCD. Combined with a microchannel patterned in the silicone, a microreactor was obtained with which the diffusion through the plasma polymerized layer and the hydrolysis of a synthetic substrate, the resorufin-β-d-galactopyranoside, were studied. A study of the efficiency of the immobilization procedure was investigated after several uses and kinetic parameters of immobilized β-galactosidase were calculated and compared with those of soluble enzyme. Simulation and a modelling approach were also initiated to understand phenomena that influenced enzyme behavior in the physical immobilization method. Thus, the catalytic performances of immobilized enzymes were directly influenced by immobilization conditions and particularly by the diffusion behavior and availability of substrate molecules in the enzyme microenvironment.

  17. Synthesis and Characterization of Nanofibrous Polyaniline Thin Film Prepared by Novel Atmospheric Pressure Plasma Polymerization Technique

    Directory of Open Access Journals (Sweden)

    Choon-Sang Park

    2016-01-01

    Full Text Available This work presents a study on the preparation of plasma-polymerized aniline (pPANI nanofibers and nanoparticles by an intense plasma cloud type atmospheric pressure plasma jets (iPC-APPJ device with a single bundle of three glass tubes. The nano size polymer was obtained at a sinusoidal wave with a peak value of 8 kV and a frequency of 26 kHz under ambient air. Discharge currents, photo-sensor amplifier, and optical emission spectrometer (OES techniques were used to analyze the plasma produced from the iPC-APPJ device. Field emission scanning electron microscopy (FE-SEM, transmission electron microscopy (TEM, Fourier transform infrared spectroscopy (FT-IR, gas chromatography-mass spectrometry (GC-MS, and gel permeation chromatography (GPC techniques were used to analyze the pPANI. FE-SEM and TEM results show that pPANI has nanofibers, nanoparticles morphology, and polycrystalline characteristics. The FT-IR and GC-MS analysis show the characteristic polyaniline peaks with evidence that some quinone and benzene rings are broken by the discharge energy. GPC results show that pPANI has high molecular weight (Mw, about 533 kDa with 1.9 polydispersity index (PDI. This study contributes to a better understanding on the novel growth process and synthesis of uniform polyaniline nanofibers and nanoparticles with high molecular weights using the simple atmospheric pressure plasma polymerization technique.

  18. Antibacterial performance on plasma polymerized heptylamine films loaded with silver nanoparticles

    Science.gov (United States)

    Lin, Yu-Chun; Lin, Chia-Chun; Lin, Chih-Hao; Wang, Meng-Jiy

    2017-01-01

    The antibacterial performance of the plasma-polymerized (pp) heptylamine thin films loaded with silver nanoparticles was evaluated against the colonization of Escherichia coli and Staphylococcus aureus. The properties including the thickness and chemical composition of the as deposited HApp films were modulated by adjusting plasma parameters. The acquired results showed that the film thickness was controlled in the range of 20 to 400 nm by adjusting deposition time. The subsequent immersion of the HApp thin films in silver nitrate solutions result in the formation of amine-metal complexes, in which the silver nanoparticles were reduced directly on the matrices to form Ag@HApp. The reduction reaction of silver was facilitated by applying NaBH4 as a reducing agent. The results of physicochemical analyses including morphological analysis and ellipsometry revealed that the silver nanoparticles were successfully reduced on the HApp films, and the amount of reduced silver was closely associated which the thickness of the plasma-polymerized films, the concentration of applied metal ions solutions, and the time of immobilization. Regarding the antibacterial performance, the Ag@HApp films reduced by NaBH4 showed antibacterial abilities of 70.1 and 68.2% against E. coli and S. aureus, respectively.

  19. Plasma polymerization of acrylic acid onto polystyrene by cyclonic plasma at atmospheric pressure

    Science.gov (United States)

    Chang, Yi-Jan; Lin, Chin-Ho; Huang, Chun

    2016-01-01

    The cyclonic atmospheric-pressure plasma is developed for chamberless deposition of poly(acrylic acid) film from argon/acrylic acid mixtures. The photoemission plasma species in atmospheric-pressure plasma polymerization was identified by optical emission spectroscopy (OES). The OES diagnosis data and deposition results indicated that in glow discharge, the CH and C2 species resulted from low-energy electron-impact dissociation that creates deposition species, but the strong CO emission lines are related to nondeposition species. The acrylic acid flow rate is seen as the key factor affecting the film growth. The film surface analysis results indicate that a smooth, continuous, and uniform surface of poly(acrylic acid) films can be formed at a relatively low plasma power input. This study reveals the potential of chamberless film growth at atmospheric pressure for large-area deposition of poly(acrylic acid) films.

  20. Photostability of plasma polymerized γ-terpinene thin films for encapsulation of OPV

    Science.gov (United States)

    Bazaka, Kateryna; Ahmad, Jakaria; Oelgemöller, Michael; Uddin, Ashraf; Jacob, Mohan V.

    2017-03-01

    Optically transparent, smooth, defect-free, chemically inert and with good adhesion to a variety of substrates, plasma polymers from plant-derived secondary metabolites have been identified as promising encapsulating materials for organic electronics and photovoltaics. Here, we demonstrate that an encapsulating layer of plasma polymerized γ-terpinene reduces degradation-related loss in conversion efficiency in PCPDTBT:PC70BM solar cells under ambient operating conditions. The stability of γ-terpinene films was then investigated under extreme UV irradiation conditions as a function of deposition power. When exposed to ambient air, prolonged exposure to UV-A and UV-B light led to notable ageing of the polymer. Photooxidation was identified as the main mechanism of degradation, confirmed by significantly slower ageing when oxygen was restricted through the use of a quartz cover. Under unnatural high-energy UV-C irradiation, significant photochemical degradation and oxidation occurred even in an oxygen-poor environment.

  1. Photostability of plasma polymerized γ-terpinene thin films for encapsulation of OPV

    Science.gov (United States)

    Bazaka, Kateryna; Ahmad, Jakaria; Oelgemöller, Michael; Uddin, Ashraf; Jacob, Mohan V.

    2017-01-01

    Optically transparent, smooth, defect-free, chemically inert and with good adhesion to a variety of substrates, plasma polymers from plant-derived secondary metabolites have been identified as promising encapsulating materials for organic electronics and photovoltaics. Here, we demonstrate that an encapsulating layer of plasma polymerized γ-terpinene reduces degradation-related loss in conversion efficiency in PCPDTBT:PC70BM solar cells under ambient operating conditions. The stability of γ-terpinene films was then investigated under extreme UV irradiation conditions as a function of deposition power. When exposed to ambient air, prolonged exposure to UV–A and UV–B light led to notable ageing of the polymer. Photooxidation was identified as the main mechanism of degradation, confirmed by significantly slower ageing when oxygen was restricted through the use of a quartz cover. Under unnatural high-energy UV–C irradiation, significant photochemical degradation and oxidation occurred even in an oxygen-poor environment. PMID:28358138

  2. Investigation of Plasma Polymerized Maleic Anhydride Film in a Middle Frequency Dielectric Barrier Discharge

    Institute of Scientific and Technical Information of China (English)

    TANG Wenjie; CHEN Qiang; ZHANG Yuefei; GE Yuanjing

    2008-01-01

    Plasma polymerized maleic anhydride (MA) was carried out by using maleic anhydride supersaturated ethanol solution as a precursor in a dielectric barrier discharge (DBD). The film properties were characterized by water contact angle (WCA), Fourier transfer infrared (FTIR), X-ray photoelectron spectroscopy (XPS), atomic force microscope (AFM) analysis, and a thickness profilometer. The influence of the processing parameters on the film properties such as the power frequency, and polymerization zone was investigated. The results show that anhydride group incorporated into the growing films is favorable at the frequency of 80 kHz and working pressure of 50 Pa. The poly (maleic anhydride) film is uniform and compact at an average deposition rate of 8 nm/min.

  3. Deposition of plasma polymerized perfluoromethylene-dominated films showing oil-repellency

    Science.gov (United States)

    Chase, J. E.; Boerio, F. J.

    2003-05-01

    Plasma polymerized fluorocarbon films were deposited onto polyethylene (PE) substrates to increase oil-repellency of PE. Depositions were performed using the monomer, 1H,1H,2H-perfluoro-1-dodecene in a parallel-plate, radio frequency (rf) reactor, with variable continuous-wave power ranging from 2 to 160 W. The film deposition rate and morphology were strongly dependent on the applied rf power. Most importantly, the chemical structure of the deposited films was also altered, resulting in changes in contact angles of various liquids and the surface energy. Films deposited at low power were composed mainly of perfluoromethylene (CF2) species (up to 67.2%), as shown by x-ray photoelectron spectroscopy (XPS). With an increase in rf power, CF2 content in the film decreased as further fragmentation of the monomer occurred. For each deposition at varying rf powers, even at powers as low as 2 W, the C=C and C-H bonds in the monomer were dissociated by the plasma and not incorporated into the films, as shown by Fourier transform infrared spectroscopy. Oil-repellency, as shown by increased contact angles of hydrocarbon liquids, was found to increase as the amount of CF2 species increased in the film structure. A low critical surface energy (2.7 mJ/m2) was calculated for the film deposited with only 2 W of rf power. Adhesion of the plasma-polymerized films to the PE was also evaluated and found to be poor for films with a high concentration of CF2 species, where cohesive failure within the film occurred. However, adhesion increased as a function of rf power, where the film structure showed more cross-linking. There was a compromise between producing a film with high oleophobicity (oil-repellency) while maintaining adhesion of the film to PE, as some disruption of the CF2 chains in the films was necessary for cohesion through cross-linking.

  4. Plasma polymerization of acetylene onto silica: an approach to control the distribution of silica in single elastomers and immiscible blends

    NARCIS (Netherlands)

    Tiwari, M.; Noordermeer, J.W.M.; Ooij, W.J.; Dierkes, W.K.

    2008-01-01

    Surface modification of silica by acetylene plasma polymerization is applied in order to improve the dispersion in and compatibility with single rubbers and their blends. Silica, used as a reinforcing filler for elastomers, is coated with a polyacetylene (PA) film under vacuum conditions. Water pene

  5. Characterization and protein-adsorption behavior of deposited organic thin film onto titanium by plasma polymerization with hexamethyldisiloxane.

    Science.gov (United States)

    Hayakawa, Tohru; Yoshinari, Masao; Nemoto, Kimiya

    2004-01-01

    Plasma polymerized hexamethyldisiloxane (HMDSO) thin film was deposited onto titanium using a radio-frequency apparatus for the surface modification of titanium. A titanium disk was first polished using colloidal silica at pH=9.8. Plasma-polymerized HMDSO films were firmly attached to the titanium by heating the titanium to a temperature of approximately 250 degrees C. The thickness of the deposited film was 0.07-0.35mum after 10-60min of plasma polymerization. The contact angle with respect to double distilled water significantly increased after HMDSO coating. X-ray photoelectron spectroscopy revealed that the deposited thin film consisted of Si, C, and O atoms. No Ti peaks were observed on the deposited surface. The deposited HMDSO film was stable during 2-weeks immersion in phosphate buffer saline solution. Fourier transform reflection-absorption spectroscopy showed the formation of Si-H, Si-C, C-H, and Cz.dbnd6;O bonds in addition to Si-O-Si bonds. Quartz crystal microbalance-dissipation measurement demonstrated that the deposition of HMDSO thin films on titanium has a benefit for fibronectin adsorption at the early stage. In conclusion, plasma polymerization is a promising technique for the surface modification of titanium. HMDSO-coated titanium has potential application as a dental implant material.

  6. Impact of low-pressure glow-discharge-pulsed plasma polymerization on properties of polyaniline thin films

    Science.gov (United States)

    Jatratkar, Aviraj A.; Yadav, Jyotiprakash B.; Deshmukh, R. R.; Barshilia, Harish C.; Puri, Vijaya; Puri, R. K.

    2016-12-01

    This study reports on polyaniline thin films deposited on a glass substrate using a low-pressure glow-discharge-pulsed plasma polymerization method. The polyaniline thin film obtained by pulsed plasma polymerization has been successfully demonstrated as an optical waveguide with a transmission loss of 3.93 dB cm-1, and has the potential to be employed in integrated optics. An attempt has been made to investigate the effect of plasma OFF-time on the structural, optical as well as surface properties of polyaniline thin film. The plasma ON-time has been kept constant and the plasma OFF-time has been varied throughout the work. The plasma OFF-time strongly influenced the properties of the polyaniline thin film, and a nanostructured and compact surface was revealed in the morphological studies. The plasma OFF-time was found to enhance film thickness, roughness, refractive index and optical transmission loss, whereas it reduced the optical band gap of the polyaniline thin films. Retention in the aromatic structure was confirmed by FTIR results. Optical studies revealed a π-π* electronic transition at about 317 nm as well as the formation of a branched structure. As compared with continuous wave plasma, pulsed plasma polymerization shows better properties. Pulsed plasma polymerization reduced the roughness of the film from 1.2 nm to 0.42 nm and the optical transmission loss from 6.56 dB cm-1 to 3.39 dB cm-1.

  7. Comparative study of nanocomposites prepared by pulsed and dc sputtering combined with plasma polymerization suitable for photovoltaic device applications

    Energy Technology Data Exchange (ETDEWEB)

    Hussain, Amreen A. [Physical Sciences Division, Institute of Advanced Study in Science and Technology, Guwahati, Assam (India); Pal, Arup R., E-mail: arpal@iasst.gov.in [Physical Sciences Division, Institute of Advanced Study in Science and Technology, Guwahati, Assam (India); Kar, Rajib [Laser and Plasma Technology Division, Bhabha Atomic Research Center, Trombay, Mumbai (India); Bailung, Heremba; Chutia, Joyanti [Physical Sciences Division, Institute of Advanced Study in Science and Technology, Guwahati, Assam (India); Patil, Dinkar S. [Laser and Plasma Technology Division, Bhabha Atomic Research Center, Trombay, Mumbai (India)

    2014-12-15

    Plasma processing, a single step method for production of large area composite films, is employed to deposit plasma polymerized aniline-Titanium dioxide (PPani-TiO{sub 2}) nanocomposite thin films. The deposition of PPani-TiO{sub 2} nanocomposite films are made using reactive magnetron sputtering and plasma polymerization combined process. This study focuses on the direct comparison between continuous and pulsed dc magnetron sputtering techniques of titanium in combination with rf plasma polymerization of aniline. The deposited PPani-TiO{sub 2} nanocomposite films are characterized and discussed in terms of structural, morphological and optical properties. A self powered hybrid photodetector has been developed by plasma based process. The proposed method provides a new route where the self-assembly of molecules, that is, the spontaneous association of atomic or molecular building blocks under plasma environment, emerge as a successful strategy to form well-defined structural and morphological units of nanometer dimensions. - Highlights: • PPani-TiO{sub 2} nanocomposite by pulsed and dc sputtering with rf plasma polymerization. • In-situ and Ex-situ H{sub 2}SO{sub 4} doping in PPani-TiO{sub 2} nanocomposite. • PPani-TiO{sub 2} nanocomposite based self-powered-hybrid photodetector.

  8. Conductive Polymer Synthesis with Single-Crystallinity via a Novel Plasma Polymerization Technique for Gas Sensor Applications

    Directory of Open Access Journals (Sweden)

    Choon-Sang Park

    2016-09-01

    Full Text Available This study proposes a new nanostructured conductive polymer synthesis method that can grow the single-crystalline high-density plasma-polymerized nanoparticle structures by enhancing the sufficient nucleation and fragmentation of the pyrrole monomer using a novel atmospheric pressure plasma jet (APPJ technique. Transmission electron microscopy (TEM, Fourier transform infrared spectroscopy (FT-IR, X-ray photoelectron spectroscopy (XPS, and field emission scanning electron microscopy (FE-SEM results show that the plasma-polymerized pyrrole (pPPy nanoparticles have a fast deposition rate of 0.93 µm·min−1 under a room-temperature process and have single-crystalline characteristics with porous properties. In addition, the single-crystalline high-density pPPy nanoparticle structures were successfully synthesized on the glass, plastic, and interdigitated gas sensor electrode substrates using a novel plasma polymerization technique at room temperature. To check the suitability of the active layer for the fabrication of electrochemical toxic gas sensors, the resistance variations of the pPPy nanoparticles grown on the interdigitated gas sensor electrodes were examined by doping with iodine. As a result, the proposed APPJ device could obtain the high-density and ultra-fast single-crystalline pPPy thin films for various gas sensor applications. This work will contribute to the design of highly sensitive gas sensors adopting the novel plasma-polymerized conductive polymer as new active layer.

  9. On the optical and electrical properties of rf and a.c. plasma polymerized aniline thin films

    Indian Academy of Sciences (India)

    U S Sajeev; C Joseph Mathai; S Saravanan; Rajeev R Ashokan; S Venkatachalam; M R Anantharaman

    2006-04-01

    Polyaniline is a widely studied conducting polymer and is a useful material in its bulk and thin film form for many applications, because of its excellent optical and electrical properties. Pristine and iodine doped polyaniline thin films were prepared by a.c. and rf plasma polymerization techniques separately for the comparison of their optical and electrical properties. Doping of iodine was effected in situ. The structural properties of these films were evaluated by FTIR spectroscopy and the optical band gap was estimated from UV-vis-NIR measurements. Comparative studies on the structural, optical and electrical properties of a.c. and rf polymerization are presented here. It has been found that the optical band gap of the polyaniline thin films prepared by rf and a.c. plasma polymerization techniques differ considerably and the band gap is further reduced by in situ doping of iodine. The electrical conductivity measurements on these films show a higher value of electrical conductivity in the case of rf plasma polymerized thin films when compared to the a.c. plasma polymerized films. Also, it is found that the iodine doping enhanced conductivity of the polymer thin films considerably. The results are compared and correlated and have been explained with respect to the different structures adopted under these two preparation techniques.

  10. Characterization of Plasma-Polymerized 4-vinyl pyridine on Poly(Ethylene Terephthalate) film for anti-microbial properties

    DEFF Research Database (Denmark)

    Jiang, Juan; Winther-Jensen, Bjørn; Kjær, Erik Michael

    2005-01-01

    . The mechanical strength of the bond between the substrate and the surface layer has been tested by several methods, and the antibacterial effect of the surface layer with and without silver nano particles has been estimated by measuring electrical resistance as a function of time. The bacteria investigated were...... the bacteria E. coli as well as some other micro organisms relevant for one of the intended uses, food packaging....

  11. Characterization of Plasma-Polymerized 4-vinyl pyridine on Poly(Ethylene Terephthalate) film for anti-microbial properties

    DEFF Research Database (Denmark)

    Jiang, Juan; Winther-Jensen, Bjørn; Kjær, Erik Michael

    2005-01-01

    a linear relation between the polymerisation time and the thickness of the surface layer. To further strengthen the antibacterial function the poly-4-vinyl-pyridine surface layer can act as the base for including nano particles of silver precipitated from a salt solution due to ultraviolet radiation....... The mechanical strength of the bond between the substrate and the surface layer has been tested by several methods, and the antibacterial effect of the surface layer with and without silver nano particles has been estimated by measuring electrical resistance as a function of time. The bacteria investigated were......As an efficient way to create an anti-bacterial function on polymer surfaces, we have used plasma polymerisation to create a poly-4-vinyl-pyridine coating on the surface of a common polymer, PET, a polymerisation process that we have shown also works well on several other polymers. We have found...

  12. Controlled chemical and morphological surface modifications via pulsed plasma polymerizations: Synthesis of ultrahydrophobic surfaces

    Science.gov (United States)

    Qiu, Haibo

    The RF plasma polymerization of saturated linear and cyclic perfluoroalkane monomers and vinyl acetic acid were studied in this dissertation. Film chemical compositions, deposition rates, surface wettabilities and morphologies were characterized as functions of various plasma processing conditions. Large progressive changes in chemical compositions with sequential variations in plasma duty cycle were demonstrated in polymerization of both perfluoroalkane and vinyl acetic acid monomers. As anticipated, polymer films obtained from the perfluorocarbon monomers exhibited a general trend towards more linear structures with decreasing plasma duty cycles. However, completely unexpectedly, ultrahydrophobic films were obtained from some of these monomers under restricted duty cycle and power input conditions. SEM and XPS characterizations revealed that a rough, fibrous-like surface morphology is responsible for this ultrahydrophobicity, as opposed to unusual chemical compositions. The growth of the fibrous surface is believed to arise from nucleation and hillock-like growth patterns on selectively activated sites of the growing polymer film. Surface mobility of plasma generated reactive species apparently plays an important role in the growth of the fibrous ultrahydrophobic surfaces, as shown by substrate temperature studies. Additionally, the present study revealed a number of interesting new observations of significant differences in the chemical compositions and deposition rates of polymer films obtained from the diverse range of perfluorocarbon monomers employed in this work. The ultrahydrophobic fluorocarbon films discovered in this investigation were evaluated for use in several biomaterial applications. The results obtained show excellent marine antifouling properties for these surfaces, as documented in ocean testing experiments. These surfaces have also been shown to be useful in controlling protein and peptide surface adsorptions, as well as in the inflammatory

  13. The molecular structure of interfaces formed between plasma polymerized silica-like films and epoxy adhesives

    Science.gov (United States)

    Bengu, Basak

    The molecular structure of the interphase formed by curing a model adhesive system consisting of the diglycidyl ether of bisphenol-A (DGEBA) and dicyandiamide (DDA) against inorganic substrates, including mechanically polished aluminum, electrogalvanized steel (EGS) and plasma polymerized silica-like primer films, was determined using reflection--absorption infrared spectroscopy (RAIR) and X-ray photoelectron spectroscopy (XPS). RAIR analysis suggested that DGEBA/DDA mixtures created an interphase with a different molecular structure from the bulk of the adhesive when cured in contact with aluminum. The formation of this unique interphase was mainly due to interactions between DDA and the Al surface. XPS analysis indicated that aluminum ions exposed by heating the substrate surface were necessary for this interaction. DDA was found to adsorb onto the aluminum surface via the lone pair of electrons on the nitrogen atoms of the nitrile groups. A slight decrease in the nitrile stretching frequency indicated an additional back-bonding interaction between aluminum ions and the nitrile groups. Slight back donation of electrons from the metal to DDA resulted in a reduction product that led to the formation of the carbodiimide form of DDA. This specific reaction caused a decrease in the concentration of nitrile groups in the interphase and changed the network structure of the epoxy adhesive in the regions close to the oxide surface. The interaction of DDA with EGS surfaces followed a similar trend. However, the effects were much more pronounced with EGS and the path of the curing reaction and the network structure near the metal surface were strongly affected by EGS/DDA interactions. Two types of plasma polymerized silica-like films were prepared from hexamethyldisiloxane (HMDSO) monomer and oxygen by varying the gas compositions. One of the films was high and the other was low in hydroxyl content. XPS results showed that adjacent to the silica-like primer films, the

  14. Deposition of stable amine coating onto polycaprolactone nanofibers by low pressure cyclopropylamine plasma polymerization

    Energy Technology Data Exchange (ETDEWEB)

    Manakhov, Anton [Plasma Technologies, CEITEC — Central European Institute of Technology, Masaryk University, Kotlářská 2, Brno 61137 (Czech Republic); Nečas, David [Plasma Technologies, CEITEC — Central European Institute of Technology, Masaryk University, Kotlářská 2, Brno 61137 (Czech Republic); Department of Physical Electronics, Faculty of Science, Masaryk University, Kotlářská 2, Brno 61137 (Czech Republic); Čechal, Jan [CEITEC — Central European Institute of Technology, Brno University of Technology, Technická 3058/10, 616 00 Brno (Czech Republic); Pavliňák, David [Department of Physical Electronics, Faculty of Science, Masaryk University, Kotlářská 2, Brno 61137 (Czech Republic); Eliáš, Marek [Plasma Technologies, CEITEC — Central European Institute of Technology, Masaryk University, Kotlářská 2, Brno 61137 (Czech Republic); Department of Physical Electronics, Faculty of Science, Masaryk University, Kotlářská 2, Brno 61137 (Czech Republic); and others

    2015-04-30

    Amine-rich films are of high interest for the bio-applications including drug delivery and tissue engineering thanks to their high reactivity allowing the formation of the covalent linkages between biomolecules and a surface. However, the bio-applications of amine-rich films require their good stability in water which is often achieved at large expenses of the amine concentration. Recently, non-toxic cyclopropylamine (CPA) has been applied for the plasma polymerization of films bearing high NH{sub x} environment combined with the moderate thickness loss (20%) after water immersion for 48 h. In this work, the amine-rich film with the NH{sub x} concentration over 7 at.% was deposited on Si substrates and polycaprolactone nanofiber meshes by using CPA plasma polymerization (pulsed mode) in a vertically oriented stainless steel reactor. The substrates were placed at the radio frequency electrode and the ion bombardment caused by direct-current self-bias was suppressed by using high pressure of 50 Pa. Analysis of samples by scanning electron microscopy did not reveal any cracks in the deposited layer formed during a sample immersion in water. Fourier transform infrared (FTIR) spectroscopy and X-ray photoelectron spectroscopy (XPS) confirmed a slight oxidation of amine groups in water but the film still contained 5 at.% of NH{sub x} (according to the N1s XPS fitting) after the immersion. The rapid oxidation of amine groups was observed during the aging experiment carried out in air at room temperature because FTIR revealed an increase of amide peaks that increased progressively with aging time. However, this oxidation was significantly reduced if the plasma polymer was stored at − 20 °C. Since the films exhibit high amine concentration and very good water stability they have great potential for applications as biocompatible functional coatings. - Highlights: • Cyclopropylamine plasma polymers deposited on polycaprolactone nanofibers • Amine-rich films with high

  15. Grafting of molecularly imprinted polymer to porous polyethylene filtration membranes by plasma polymerization.

    Science.gov (United States)

    Cowieson, D; Piletska, E; Moczko, E; Piletsky, S

    2013-08-01

    An application of plasma-induced grafting of polyethylene membranes with a thin layer of molecularly imprinted polymer (MIP) was presented. High-density polyethylene (HDPE) membranes, "Vyon," were used as a substrate for plasma grafting modification. The herbicide atrazine, one of the most popular targets of the molecular imprinting, was chosen as a template. The parameters of the plasma treatment were optimized in order to achieve a good balance between polymerization and ablation processes. Modified HDPE membranes were characterized, and the presence of the grafted polymeric layer was confirmed based on the observed weight gain, pore size measurements, and infrared spectrometry. Since there was no significant change in the porosity of the modified membranes, it was assumed that only a thin layer of the polymer was introduced on the surface. The experiments on the re-binding of the template atrazine to the membranes modified with MIP and blank polymers were performed. HDPE membranes which were grafted with polymer using continuous plasma polymerization demonstrated the best result which was expressed in an imprinted factor equal to 3, suggesting that molecular imprinting was successfully achieved.

  16. Surface modification of SERS substrates with plasma-polymerized trimethylsilane nanocoating

    Science.gov (United States)

    Kim, Young Jo; Sun, Xin; Jones, John E.; Lin, Mengshi; Yu, Qingsong; Li, Hao

    2015-03-01

    Surface-enhanced Raman scattering (SERS) substrates were modified by depositing a nanometer-thick polymer coating on top of SERS-active surface. This thin hydrophobic nanocoating, achieved by low temperature plasma polymerization of trimethylsilane, was found to reduce surface energy of SERS substrate and in turn help relieve the analyte spreading on the surface of SERS substrates. Detection of melamine molecules with these surface-modified SERS substrates showed that this plasma nanocoating improved, not significantly though, SERS sensitivity in comparison with unmodified SERS substrates. It is believed that the increased hydrophobicity induced by this plasma nanocoating had two folds of beneficial effects on SERS sensitivity. First, the as-produced hydrophobic surface gave rise to preconcentration effect due to the reduced contact area between analyte molecules and the substrate surface. Second, the decreased surface energy of SERS substrates was helpful in placing analyte molecules in SERS hot spots. These two combined gains were deemed to outweigh the loss of SERS sensitivity caused by enlarged distance between metal surface and analyte molecules.

  17. Nanomechanical properties of advanced plasma polymerized coatings for mechanical data storage.

    Science.gov (United States)

    Tranchida, Davide; Pihan, Sascha A; Zhang, Yi; Schönherr, Holger; Berger, Rüdiger

    2011-04-07

    In this paper we report on the unprecedented deformation behavior of stratified ultrathin polymer films. The mechanical behavior of layered nanoscale films composed of 8-12 nm thin plasma polymerized hexamethyldisiloxane (ppHMDSO) films on a 70 nm thick film of polystyrene was unveiled by atomic force microscopy nanoindentation. In particular, we observed transitions from the deformation of a thin plate under point load to an elastic contact of a paraboloid of revolution, followed by an elastic-plastic contact for polystyrene and finally an elastic contact for silicon. The different deformation modes were identified on the basis of force-penetration data and atomic force microscopy images of residual indents. A clear threshold was observed for the onset of plastic deformation of the films at loads larger than 2 μN. The measured force curves are in agreement with an elastic and elastic-plastic contact mechanics model, taking the amount of deformation and the geometry of the layer that presumably contributed more to the overall deformation into account. This study shows that the complex deformation behavior of advanced soft matter systems with nanoscale dimensions can be successfully unraveled.

  18. Spectroscopic Study of Plasma Polymerized a-C:H Films Deposited by a Dielectric Barrier Discharge

    Directory of Open Access Journals (Sweden)

    Thejaswini Halethimmanahally Chandrashekaraiah

    2016-07-01

    Full Text Available Plasma polymerized a-C:H thin films have been deposited on Si (100 and aluminum coated glass substrates by a dielectric barrier discharge (DBD operated at medium pressure using C2Hm/Ar (m = 2, 4, 6 gas mixtures. The deposited films were characterized by Fourier transform infrared reflection absorption spectroscopy (FT-IRRAS, Raman spectroscopy, and ellipsometry. FT-IRRAS revealed the presence of sp3 and sp2 C–H stretching and C–H bending vibrations of bonds in the films. The presence of D and G bands was confirmed by Raman spectroscopy. Thin films obtained from C2H4/Ar and C2H6/Ar gas mixtures have ID/IG ratios of 0.45 and 0.3, respectively. The refractive indices were 2.8 and 3.1 for C2H4/Ar and C2H6/Ar films, respectively, at a photon energy of 2 eV.

  19. Varying stress of SiOsub>xsub>Csub>ysub> thin films deposited by plasma polymerization.

    Science.gov (United States)

    Liao, Wei-Bo; Chang, Ya-Chen; Jaing, Cheng-Chung; Cheng, Ching-Long; Lee, Cheng-Chung; Wei, Hung-Sen; Kuo, Chien-Cheng

    2017-02-01

    SiOsub>xsub>Csub>ysub> thin films were deposited by plasma polymerization. The stress of the deposited SiOsub>xsub>Csub>ysub> thin films can be modified by adjusting the beam current, the anode voltage, and the flow rate of hexamethyldisiloxane (HMDSO) gas and oxygen. Reducing the beam current or increasing the flow rate of HMDSO gas increased the linear/cage structure ratio and turned the stress of the SiOsub>xsub>Csub>ysub> thin films from compressive to tensile. The linear/cage structure ratio can be adjusted by changing the composite parameter, W[FM]sub>csub>/[FM]sub>msub>, to control the stress of the deposited plasma polymer films. Multilayers of TiOsub>2sub>/SiOsub>2sub>/TiOsub>2sub> were coated on a SiOsub>xsub>Csub>ysub> plasma polymer film herein, reducing their stress by 70% from 0.06 to 0.018 GPa. The refractive index is 1.55, and the absorption coefficient is less than 10-4 at 550 nm of the SiOsub>xsub>Csub>ysub> films. Superior optical performances of SiOsub>xsub>Csub>ysub> thin films make their use in optical thin films.

  20. Plasma-polymerized hexamethyldisilazane treated by nitrogen plasma immersion ion implantation technique

    Energy Technology Data Exchange (ETDEWEB)

    Honda, R Y; Mota, R P; Batocki, R G S; Santos, D C R; Nicoleti, T; Kostov, K G; Kayama, M E; Algatti, M A [Laboratorio de Plasma, Faculdade de Engenharia, UNESP, Av. Dr Ariberto Pereira da Cunha-333, 12516-410, Guaratingueta, SP (Brazil); Cruz, N C [Laboratorio de Plasmas Tecnologicos, Unidade Diferenciada, UNESP, Av. Tres de Marco-511, 18085-180, Sorocaba, SP (Brazil); Ruggiero, L, E-mail: honda@feg.unesp.b [Faculdade de Ciencias, UNESP, Av. Luis E. Carrijo Coube 14-1, 17033-360, Bauru, SP (Brazil)

    2009-05-01

    This paper describes the effect of nitrogen Plasma Immersion Ion Implantation (PIII) on chemical structure, refraction index and surface hardness of plasma-polymerized hexamethyldisilazane (PPHMDSN) thin films. Firstly, polymeric films were deposited at 13.56 MHz radiofrequency (RF) Plasma Enhanced Chemical Vapour Deposition (PECVD) and then, were treated by nitrogen PIII from 15 to 60 min. Fourier Transformed Infrared (FTIR) spectroscopy was employed to analyse the molecular structure of the samples, and it revealed that vibrations modes at 3350 cm{sup -1}, 2960 cm{sup -1}, 1650 cm{sup -1}, 1250 cm{sup -1} and 1050 cm{sup -1} were altered by nitrogen PIII. Visible-ultraviolet (vis-UV) spectroscopy was used to evaluate film refractive index and the results showed a slight increase from 1.6 to 1.8 following the implantation time. Nanoindentation revealed a surface hardness rise from 0.5 to 2.3 GPa as PIII treatment time increased. These results indicate nitrogen PIII is very promising in improving optical and mechanical properties of PPHMDSN films.

  1. Polyurethane coating with thin polymer films produced by plasma polymerization of diglyme

    Energy Technology Data Exchange (ETDEWEB)

    Ribeiro, M A; Ramos, A S; Manfredini, M I; Alves, H A; Ramos, E C T [UNIVAP, Sao Jose dos Campos, SP (Brazil); Honda, R Y; Kostov, K G; Lucena, E F; Mota, R P; Algatti, M A; Kayama, M E, E-mail: rmota@feg.unesp.b [FEG-DFQ-UNESP, Av. Ariberto Pereira da Cunha 333, 12516-410 - Guaratingueta, SP (Brazil)

    2009-05-01

    Aqueous-based polyurethane dispersions have been widely utilized as lubricants in textile, shoes, automotive, biomaterial and many other industries because they are less aggressive to surrounding environment. In this work thin films with different thickness were deposited on biocompatible polyurethane by plasma polymerization process using diethylene glycol dimethyl ether (Diglyme) as monomer. Molecular structure of the films was analyzed by Fourier Transform Infrared spectroscopy. The spectra exhibited absorption bands of O-H (3500-3200cm{sup -1}), C-H (3000-2900cm{sup -1}), C=O (1730-1650cm{sup -1}), C-O and C-O-C bonds at 1200-1600cm{sup -1}. The samples wettability was evaluated by measurements of contact angle using different liquids such as water, glycerol, poly-ethane and CMC. The polyurethane surface showed hydrophilic behavior after diglyme plasma-deposition with contact angle dropping from 85 deg. to 22 deg. Scanning Electron Microscopy revealed that diglyme films covered uniformly the polyurethane surfaces ensuring to it a biocompatible characteristic.

  2. Improvement of the water selectivity of ULTEM poly(ether imide) pervaporation films by an allylamine-plasma-polymerized layer

    OpenAIRE

    Kaba, Meriyam; Raklaoui, Nabil; Guimon, Marie Françoise; Mas, André

    2005-01-01

    International audience; The wettability and surface energy of extruded ULTEM poly(ether imide) films strongly increased (the water contact angle varied from 75 to 38° and the surface energy varied from 45.3 to 59.5 mJ m-2, respectively) with the deposition of an allylamine-plasma-polymerized layer and were characterized with X-ray photoelectron spectroscopy, scanning electron microscopy, and atomic force microscopy according to the experimental parameters. Pervaporation tests for dehydrating ...

  3. Hydrophobic Coatings on Cotton Obtained by in Situ Plasma Polymerization of a Fluorinated Monomer in Ethanol Solutions.

    Science.gov (United States)

    Molina, Ricardo; Teixidó, Josep Maria; Kan, Chi-Wai; Jovančić, Petar

    2017-02-15

    Plasma polymerization using hydrophobic monomers in the gas phase is a well-known technology to generate hydrophobic coatings. However, synthesis of functional hydrophobic coatings using plasma technology in liquids has not yet been accomplished. This work is consequently focused on polymerization of a liquid fluorinated monomer on cotton fabric initiated by atmospheric plasma in a dielectric barrier discharge configuration. Functional hydrophobic coatings on cotton were successfully achieved using in situ atmospheric plasma-initiated polymerization of fluorinated monomer dissolved in ethanol. Gravimetric measurements reveal that the amount of polymer deposited on cotton substrates can be modulated with the concentration of monomer in ethanol solution, and cross-linking reactions occur during plasma polymerization of a fluorinated monomer even without the presence of a cross-linking agent. FTIR and XPS analysis were used to study the chemical composition of hydrophobic coatings and to get insights into the physicochemical processes involved in plasma treatment. SEM analysis reveals that at high monomer concentration, coatings possess a three-dimensional pattern with a characteristic interconnected porous network structure. EDX analysis reveals that plasma polymerization of fluorinated monomers takes place preferentially at the surface of cotton fabric and negligible polymerization takes place inside the cotton fabric. Wetting time measurements confirm the hydrophobicity of cotton coatings obtained although equilibrium moisture content was slightly decreased. Additionally, the abrasion behavior and resistance to washing of plasma-coated cotton has been evaluated.

  4. Combinatorial plasma polymerization approach to produce thin films for testing cell proliferation.

    Science.gov (United States)

    Antonini, V; Torrengo, S; Marocchi, L; Minati, L; Dalla Serra, M; Bao, G; Speranza, G

    2014-01-01

    Plasma enhanced physical vapor depositions are extensively used to fabricate substrates for cell culture applications. One peculiarity of the plasma processes is the possibility to deposit thin films with reproducible chemical and physical properties. In the present work, a combinatorial plasma polymerization process was used to deposit thin carbon based films to promote cell adhesion, in the interest of testing cell proliferation as a function of the substrate chemical properties. Peculiarity of the combinatorial approach is the possibility to produce in just one deposition experiment, a set of surfaces of varying chemical moieties by changing the precursor composition. A full characterization of the chemical, physical and thermodynamic properties was performed for each set of the synthesized surfaces. X-ray photoelectron spectroscopy was used to measure the concentration of carboxyl, hydroxyl and amine functional groups on the substrate surfaces. A perfect linear trend between polar groups' density and precursors' concentration was found. Further analyses reveled that also contact angles and the correspondent surface energies of all deposited thin films are linearly dependent on the precursor concentration. To test the influence of the surface composition on the cell adhesion and proliferation, two cancer cell lines were utilized. The cell viability was assessed after 24 h and 48 h of cell culture. Experiments show that we are able to control the cell adhesion and proliferation by properly changing the thin film deposition conditions i.e. the concentration and the kind of chemical moiety on the substrate surface. The results also highlight that physical and chemical factors of biomaterial surface, including surface hydrophobicity and free energy, chemical composition, and topography, can altered cell attachment.

  5. Decreased material-activation of the complement system using low-energy plasma polymerized poly(vinyl pyrrolidone) coatings

    DEFF Research Database (Denmark)

    Andersen, T.E.; Kolmos, H.J.; Palarasah, Yaseelan

    2011-01-01

    surface. The ppVP surface is furthermore characterized physically and chemically using scanning electron microscopy (SEM), x-ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FTIR), which indicates preservation of chemical functionality by the applied plasma process. Overall, the pp......In the current study we investigate the activation of blood complement on medical device silicone rubber and present a plasma polymerized vinyl pyrrolidone (ppVP) coating which strongly decreases surface-activation of the blood complement system. We show that uncoated silicone and polystyrene...

  6. STUDIES ON THE PERMEABILITY OF PVC /EBBA OVERLAPPED ULTRATHIN COMPOSITE MEMBRANES MODIFIED BY PLASMA- POLYMERIZATION WITH FLUOROCARBON MONOMERS

    Institute of Scientific and Technical Information of China (English)

    FU Xiucheng; JIN Xigao; Tisato KAJIYAMA

    1989-01-01

    The PVC/EBBA ultrathin composite membranes with thickness of about 100 nm were prepared by spreading the solution on water surface. The overlapped composite membrane showed a characteristic aggregation structure in which the polymer matrix exists as a three-dimensional spongy network and the liquid crystal domains were observedThe surface modification for the overlapped membranes was carried out by means of plasma-polymerization with the monomers of fluorocarbon compounds. Both Arrhenius plots of permeability coefficients for oxygen (-Po2) in the membrane samples before and after modification showed significant increase in the vicinity of the TKN of EBBA.

  7. Modification of Polyester and Polyamide Fabrics by Different in Situ Plasma Polymerization Methods

    OpenAIRE

    ÖKTEM, T.; SEVENTEKİN, N.

    2000-01-01

    In order to increase the hydrophilicities, and therefore to impart soil resistance and to improve dyeability, poly(ethylene terephthalate) (PET) and polyamide (PAm) fabrics were treated in low-temperature plasmas. Five different modification types were applied. Fabrics were directly treated in acrylic acid, water, air, O2 and argon plasma. The plasma conditions (i.e., exposure time and discharge power) were changed to control the extent of plasma surface modification. Wettability, soil resist...

  8. Enzyme biosensor based on plasma-polymerized film-covered carbon nanotube layer grown directly on a flat substrate.

    Science.gov (United States)

    Muguruma, Hitoshi; Hoshino, Tatsuya; Matsui, Yasunori

    2011-07-01

    We report a novel approach to fabrication of an amperometric biosensor with an enzyme, a plasma-polymerized film (PPF), and carbon nanotubes (CNTs). The CNTs were grown directly on an island-patterned Co/Ti/Cr layer on a glass substrate by microwave plasma enhanced chemical vapor deposition. The as-grown CNTs were subsequently treated by nitrogen plasma, which changed the surface from hydrophobic to hydrophilic in order to obtain an electrochemical contact between the CNTs and enzymes. A glucose oxidase (GOx) enzyme was then adsorbed onto the CNT surface and directly treated with acetonitrile plasma to overcoat the GOx layer with a PPF. This fabrication process provides a robust design of CNT-based enzyme biosensor, because of all processes are dry except the procedure for enzyme immobilization. The main novelty of the present methodology lies in the PPF and/or plasma processes. The optimized glucose biosensor revealed a high sensitivity of 38 μA mM(-1) cm(-2), a broad linear dynamic range of 0.25-19 mM (correlation coefficient of 0.994), selectivity toward an interferent (ascorbic acid), and a fast response time of 7 s. The background current was much smaller in magnitude than the current due to 10 mM glucose response. The low limit of detection was 34 μM (S/N = 3). All results strongly suggest that a plasma-polymerized process can provide a new platform for CNT-based biosensor design.

  9. Surface functionalization of an osteoconductive filler by plasma polymerization of poly(ε-caprolactone) and poly(acrylic acid) films

    Science.gov (United States)

    Petisco-Ferrero, S.; Sánchez-Ilárduya, M. B.; Díez, A.; Martín, L.; Meaurio Arrate, E.; Sarasua, J. R.

    2016-11-01

    One of the major limitations found in the use of nanocomposites based on synthetic hydroxyapatite and polymeric matrix for bone-tissue regeneration lies in the poor interfacial adhesion between the inorganic filler and the polymer matrix. The integrity of the nanocomposite is severely compromised since, on the one hand, high surface fillers tend to form aggregates and on the other, there is no chemical bonding between these two different categories of materials. Thus, customized surface functionalization stands as an effective route to improve the interfacial behaviour between particles and polymeric matrices. Amongst the current state of development of coating technologies, the high film-chemistry controllability offered by plasma polymerization technology enhances the synthesis of polymeric films from virtually any starting organic monomer. In this sense, the work presented here provides strong evidences of surface functionalization achieved by plasma polymerization starting respectively from ε-caprolactone and acrylic acid monomers. The chemistry of the deposited films has been descriptively analysed by XPS demonstrating outstanding retention of monomer functionalities and FTIR spectra of the deposited films revealed a high resemblance to those obtained by conventional synthesis. Results provided thereof are expected to significantly contribute to improve the interfacial behaviour in terms of matrix-reinforcement compatibilization, of crucial importance for bone-tissue engineering applications.

  10. A study of Corrosion Protection of Aluminum Metal by Tetraethoxysilane Plasma Polymerized Coatings-Influence of Aluminum Surface Pretreatments-

    Institute of Scientific and Technical Information of China (English)

    YoshihiroMomose; TatsuyaYabuki

    2004-01-01

    The corrosion-protective performance of plasma-polymerized (PP) coatings on pretreated aluminum substrates has been investigated by cathodic polarization curve measurement. The surface composition and electronic properties of the pretreated and PP film coated metal surfaces were also characterized by XPS and the temperature-programmed photoelectron emission (TPPE). A PP coating was prepared on the pretreated surfaces by plasma polymerization of a mixture of tetraethoxysilane (TEOS) monomer vapor and oxygen using a 13.56MHz radiofrequency generator. The polarization curve of PP film coated samples was measured in NaC1 aqueous solution. The weight loss rate calculated from the value of the corrosion current of the curve was used to estimate the protective performance of the PP film coated samples. Argon plasma treatment of the metal surface gave much better corrosion-protective performance than pretreatments such as oxidation by heating in air and diamond scratching. The XPS analysis indicated that the silicon oxide assigned to SiO2 was formed on the PP film coated surface. The TPPE analysis revealed that the electron emission characteristics for the metal surfaces pretreated only were strongly influenced by the pretreatments, while all the PP film coated samples exhibited nearly the same electron emission trend with a much decreased intensity.

  11. A study of Corrosion Protection of Aluminum Metal by Tetraethoxysilane Plasma Polymerized Coatings -Influence of Aluminum Surface Pretreatments-

    Institute of Scientific and Technical Information of China (English)

    Yoshihiro Momose; Tatsuya Yabuki

    2004-01-01

    The corrosion-protective performance of plasma-polymerized (PP) coatings on pretreated aluminum substrates has been investigated by cathodic polarization curve measurement. The surface composition and electronic properties of the pretreated and PP film coated metal surfaces were also characterized by XPS and the temperature-programmed photoelectron emission (TPPE). A PP coating was prepared on the pretreated surfaces by plasma polymerization of a mixture of tetraethoxysilane (TEOS) monomer vapor and oxygen using a 13.56MHz radiofrequency generator. The polarization curve of PP film coated samples was measured in NaCl aqueous solution. The weight loss rate calculated from the value of the corrosion current of the curve was used to estimate the protective performance of the PP film coated samples. Argon plasma treatment of the metal surface gave much better corrosion-protective performance than pretreatments such as oxidation by heating in air and diamond scratching. The XPS analysis indicated that the silicon oxide assigned to SiO2 was formed on the PP film coated surface. The TPPE analysis revealed that the electron emission characteristics for the metal surfaces pretreated only were strongly influenced by the pretreatments, while all the PP film coated samples exhibited nearly the same electron emission trend with a much decreased intensity.

  12. Surface modification of blood-contacting biomaterials by plasma-polymerized superhydrophobic films using hexamethyldisiloxane and tetrafluoromethane as precursors

    Energy Technology Data Exchange (ETDEWEB)

    Hsiao, Chaio-Ru [Department of Materials Science and Engineering, Feng Chia University, No. 100, Wenhwa Rd., Seatwen District, Taichung City 40724, Taiwan (China); Lin, Cheng-Wei [Department of Dental Technology and Materials Science, Central Taiwan University of Science and Technology, No. 666, Buzih Rd., Beitun District, Taichung City 40601, Taiwan (China); Chou, Chia-Man, E-mail: cmchou@vghtc.gov.tw [Department of Surgery, Taichung Veterans General Hospital, No. 1650, Sec. 4, Taiwan Boulevard, Seatwen District, Taichung City 40705, Taiwan (China); Department of Medicine, National Yang-Ming University, No. 155, Sec. 2, Linong Street, Beitou District, Taipei City 11221, Taiwan (China); Chung, Chi-Jen, E-mail: cjchung@seed.net.tw [Department of Dental Technology and Materials Science, Central Taiwan University of Science and Technology, No. 666, Buzih Rd., Beitun District, Taichung City 40601, Taiwan (China); He, Ju-Liang [Department of Materials Science and Engineering, Feng Chia University, No. 100, Wenhwa Rd., Seatwen District, Taichung City 40724, Taiwan (China)

    2015-08-15

    Highlights: • Biomaterials modified by nanoparticle-containing plasma polymerized films. • A superhydrophoic film was obtained, and the properties of the coating were examined. • In vitro blood compatibility tests revealed neither platelet adhesion nor fibrinogen adsorption. • Surface modification technology of medical devices: non-cytotoxic and no blood clot formation. - Abstract: This paper proposes a plasma polymerization system that can be used to modify the surface of the widely used biomaterial, polyurethane (PU), by employing low-cost hexamethyldisiloxane (HMDSO) and tetrafluoromethane (CF{sub 4}) as precursors; this system features a pulsed-dc power supply. Plasma-polymerized HMDSO/CF{sub 4} (pp-HC) with coexisting micro- and nanoscale morphology was obtained as a superhydrophobic coating material by controlling the HMDSO/CF{sub 4} (f{sub H}) monomer flow ratio. The developed surface modification technology can be applied to medical devices, because it is non-cytotoxic and has favorable hemocompatibility, and no blood clots form when the device surface direct contacts. Experimental results reveal that the obtained pp-HC films contained SiO{sub x} nanoparticles randomly dispersed on the micron-scale three-dimensional network film surface. The −CF functional group, −CF{sub 2} bonding, and SiO{sub x} were detected on the film surface. The maximal water contact angle of the pp-HC coating was 161.2°, apparently attributable to the synergistic effect of the coexisting micro- and nanoscale surface morphology featuring a low surface-energy layer. The superhydrophobic and antifouling characteristics of the coating were retained even after it was rubbed 20 times with a steel wool tester. Results of in vitro cytotoxicity, fibrinogen adsorption, and platelet adhesion tests revealed favorable myoblast cell proliferation and the virtual absence of fibrinogen adsorption and platelet adhesion on the pp-HC coated specimens. These quantitative findings imply

  13. Plasma Polymerized Thin Films of Maleic Anhydride and 1,2-methylenedioxybenzene for Improving Adhesion to Carbon Surfaces

    DEFF Research Database (Denmark)

    Drews, Joanna Maria; Goutianos, Stergios; Kingshott, Peter

    2007-01-01

    Low power 2-phase AC plasma polymerization has been used to surface modify glassy carbon substrates that are used as an experimental model for carbon fibers in reinforced composites. In order to probe the role of carboxylic acid density on the interfacial adhesion strength a combination...... of different plasma powers and monomer compositions was used. Maleic anhydride (MAR) and 1,2-methylenedioxybenzene (MDOB) were plasma deposited separately and as mixtures to create layers with different surface compositions. In all cases the MAR was hydrolyzed to form carboxylic acid groups. Some carboxylic...... total veflectanc~ Fourier transform infrared spectroscopy. Atomic force microscopy was used to measure the thickness of the plasma films and to monitor the surface roughness for the different polymerization conditions. Finally, preliminary results of fracture energy measurements of the plasma modified...

  14. Surface modification of blood-contacting biomaterials by plasma-polymerized superhydrophobic films using hexamethyldisiloxane and tetrafluoromethane as precursors

    Science.gov (United States)

    Hsiao, Chaio-Ru; Lin, Cheng-Wei; Chou, Chia-Man; Chung, Chi-Jen; He, Ju-Liang

    2015-08-01

    This paper proposes a plasma polymerization system that can be used to modify the surface of the widely used biomaterial, polyurethane (PU), by employing low-cost hexamethyldisiloxane (HMDSO) and tetrafluoromethane (CF4) as precursors; this system features a pulsed-dc power supply. Plasma-polymerized HMDSO/CF4 (pp-HC) with coexisting micro- and nanoscale morphology was obtained as a superhydrophobic coating material by controlling the HMDSO/CF4 (fH) monomer flow ratio. The developed surface modification technology can be applied to medical devices, because it is non-cytotoxic and has favorable hemocompatibility, and no blood clots form when the device surface direct contacts. Experimental results reveal that the obtained pp-HC films contained SiOx nanoparticles randomly dispersed on the micron-scale three-dimensional network film surface. The sbnd CF functional group, sbnd CF2 bonding, and SiOx were detected on the film surface. The maximal water contact angle of the pp-HC coating was 161.2°, apparently attributable to the synergistic effect of the coexisting micro- and nanoscale surface morphology featuring a low surface-energy layer. The superhydrophobic and antifouling characteristics of the coating were retained even after it was rubbed 20 times with a steel wool tester. Results of in vitro cytotoxicity, fibrinogen adsorption, and platelet adhesion tests revealed favorable myoblast cell proliferation and the virtual absence of fibrinogen adsorption and platelet adhesion on the pp-HC coated specimens. These quantitative findings imply that the pp-HC coating can potentially prevent the formation of thrombi and provide an alternative means of modifying the surfaces of blood-contacting biomaterials.

  15. Understanding the charge carrier conduction mechanisms of plasma-polymerized 2-furaldehyde thin films via DC electrical studies

    Energy Technology Data Exchange (ETDEWEB)

    Kabir, Humayun, E-mail: HXK598@bham.ac.uk [Department of Physics, Jahangirnagar University, Savar, Dhaka 1342 (Bangladesh); School of Metallurgy and Materials, University of Birmingham, Edgbaston, Birmingham B15 2TT (United Kingdom); Bhuiyan, A.H. [Department of Physics, Bangladesh University of Engineering & Technology, Dhaka 1000 (Bangladesh); Rahman, M. Mahbubur [Department of Physics, Jahangirnagar University, Savar, Dhaka 1342 (Bangladesh); Surface Analysis and Materials Engineering Research Group, School of Engineering & Information Technology, Murdoch University, Perth, Western Australia 6150 (Australia)

    2016-06-30

    Monomer 2-furaldehyde (FDH) was deposited onto the glass substrates in optimum conditions via a glow discharge using a capacitively coupled parallel plate reactor to obtain plasma polymerized 2-furaldehyde (PPFDH) thin films of different thicknesses. In order to realize the carrier conduction mechanisms, the direct current density against applied voltage (J–V) characteristics of these films with different thicknesses were investigated at different temperatures (T) in the voltage region from 0.5 to 49 V in Al/PPFDH/Al sandwich configuration. The J–V characteristics at various temperatures follow a power law of the form J ∞ V{sup n}. In the low voltage region the values of n were recorded to be 0.80 ≤ n ≤ 1.12 and those in the high voltage region found to lie between 1.91 ≤ n ≤ 2.58, demonstrating the Ohmic conduction mechanism in the low voltage region and non-Ohmic conduction in the high voltage region. Theoretically calculated and experimental results of Schottky (β{sub s}) and Poole–Frenkel (β{sub PF}) coefficients display that the most probable conduction mechanism in PPFDH thin films is the Schottky type. Arrhenius plots of J vs. 1/T for an applied voltage of 5 V, the activation energies were 0.13 ± 0.02 and 0.50 ± 0.05 eV in the low and high temperature regions, respectively. However, for an applied voltage of 35 V, the activation energy values were found to be 0.11 ± 0.01 eV and 0.55 ± 0.02 eV, respectively in low and high temperature regions. - Highlights: • Plasma polymerized 2-furaldehyde films were synthesized via a glow discharge technique. • Uniformity of the surface of the PPDFH films was identified via SEM analysis. • Energy dispersive X-ray spectra show the presence of C, O, and substrate related elements. • The dominant conduction mechanism in the PPFDH films is of Schottky type. • Schottky type mechanism was also confirmed by the temperature dependence J–V studies.

  16. Preparation and characterization of ethylenediamine and cysteamine plasma polymerized films on piezoelectric quartz crystal surfaces for a biosensor

    Energy Technology Data Exchange (ETDEWEB)

    Mutlu, Selma [Department of Chemical Engineering, Hacettepe University, Beytepe Campus, 06800 Ankara (Turkey)], E-mail: smselma@hacettepe.edu.tr; Coekeliler, Dilek [Plasma Aided Bioengineering and Biotechnology Research Group(PABB), Faculty of Engineering, Hacettepe University, Beytepe Campus, 06800 Ankara (Turkey); Shard, Alex [Department of Engineering Materials, The University of Sheffield, Sir Robert Hadfield Building, Mappin Street, Sheffield, S1 3JD (United Kingdom); Goktas, Hilal [Physics Department, Canakkale Onsekiz Mart University, 17100 Canakkale (Turkey); Ozansoy, Berna [Department of Chemical Engineering, Hacettepe University, Beytepe Campus, 06800 Ankara (Turkey); Mutlu, Mehmet [Plasma Aided Bioengineering and Biotechnology Research Group(PABB), Faculty of Engineering, Hacettepe University, Beytepe Campus, 06800 Ankara (Turkey)

    2008-01-30

    This paper describes a method for the modification of quartz crystal surfaces to be used as a transducer in biosensors that allow recognition and quantification of certain biomolecules (antibodies, enzymes, proteins, etc). Quartz crystal sensors were modified by a plasma based electron beam generator in order to detect the level of the toxin histamine within biological liquids (blood, serum) and food (wine, cheese, fish etc.). Cysteamine and ethylenediamine were used as precursors in the plasma. After each modification step, the layers on the quartz crystal were characterized by frequency measurements. Modified surfaces were also characterized by contact angle, X-ray photoelectron spectroscopy and atomic force microscopy to determine the physical and chemical characteristics of the surfaces after each modification. Finally, the performance of the sensors were tested by the response to histamine via frequency shifts. The frequency shifts of the sensors prepared by plasma polymerization of ethylenediamine and cysteamine were approximately 3230 Hz and 5630 Hz, respectively, whereas the frequency change of the unmodified crystal surface was around 575 Hz.

  17. Influence of the radio-frequency power on the physical and optical properties of plasma polymerized cyclohexane thin films

    Energy Technology Data Exchange (ETDEWEB)

    Manaa, C., E-mail: chadlia.el.manaa@gmail.com [Laboratoire de Physique de la Matière Condensée, Université de Picardie Jules Verne, UFR des Sciences d' Amiens, 33 rue Saint Leu, 80039 Amiens CEDEX 2 (France); Laboratoire des Matériaux Avancés et Phénomènes Quantiques, Université de Tunis El-Manar, Faculté des Sciences de Tunis, Campus universitaire El-Manar, 1068 Tunis (Tunisia); Lejeune, M. [Laboratoire de Physique de la Matière Condensée, Université de Picardie Jules Verne, UFR des Sciences d' Amiens, 33 rue Saint Leu, 80039 Amiens CEDEX 2 (France); Kouki, F. [Laboratoire des Matériaux Avancés et Phénomènes Quantiques, Université de Tunis El-Manar, Faculté des Sciences de Tunis, Campus universitaire El-Manar, 1068 Tunis (Tunisia); Durand-Drouhin, O. [Laboratoire de Physique de la Matière Condensée, Université de Picardie Jules Verne, UFR des Sciences d' Amiens, 33 rue Saint Leu, 80039 Amiens CEDEX 2 (France); Bouchriha, H. [Laboratoire des Matériaux Avancés et Phénomènes Quantiques, Université de Tunis El-Manar, Faculté des Sciences de Tunis, Campus universitaire El-Manar, 1068 Tunis (Tunisia); and others

    2014-06-02

    We investigate in the present study the effects of the radio-frequency plasma power on the opto-electronical properties of the polymeric amorphous hydrogenated carbon thin films deposited at room temperature and different radio-frequency powers by plasma-enhanced chemical vapor deposition method using cyclohexane as precursor. A combination of U.V.–Visible and infrared transmission measurements is applied to characterize the bonding and electronic properties of these films. Some film properties namely surface roughness, contact angle, surface energy, and optical properties are found to be significantly influenced by the radio-frequency power. The changes in these properties are analyzed within the microstructural modifications occurring during growth. - Highlights: • Effects of the radio-frequency power on the optoelectronic properties of thin films • Elaboration of plasma polymerized thin films using cyclohexane as precursor gas • The use of U.V.–Visible-infrared transmission, and optical gap • Study of the surface topography of the films by using Atomic Force microscopy • The use of a capacitively coupled plasma enhanced chemical vapor deposition method.

  18. Wetting, Solubility and Chemical Characteristics of Plasma-Polymerized 1-Isopropyl-4-Methyl-1,4-Cyclohexadiene Thin Films

    Directory of Open Access Journals (Sweden)

    Jakaria Ahmad

    2014-07-01

    Full Text Available Investigations on the wetting, solubility and chemical composition of plasma polymer thin films provide an insight into the feasibility of implementing these polymeric materials in organic electronics, particularly where wet solution processing is involved. In this study, thin films were prepared from 1-isopropyl-4-methyl-1,4-cyclohexadiene (γ-Terpinene using radio frequency (RF plasma polymerization. FTIR showed the polymers to be structurally dissimilar to the original monomer and highly cross-linked, where the loss of original functional groups and the degree of cross-linking increased with deposition power. The polymer surfaces were hydrocarbon-rich, with oxygen present in the form of O–H and C=O functional groups. The oxygen content decreased with deposition power, with films becoming more hydrophobic and, thus, less wettable. The advancing and receding contact angles were investigated, and the water advancing contact angle was found to increase from 63.14° to 73.53° for thin films prepared with an RF power of 10 W to 75 W. The wetting envelopes for the surfaces were constructed to enable the prediction of the surfaces’ wettability for other solvents. The effect of roughness on the wetting behaviour of the films was insignificant. The polymers were determined to resist solubilization in solvents commonly used in the deposition of organic semiconducting layers, including chloroform and chlorobenzene, with higher stability observed in films fabricated at higher RF power.

  19. In vitro cell culture, platelet adhesion tests and in vivo implant tests of plasma-polymerized para-xylene films

    Energy Technology Data Exchange (ETDEWEB)

    Chou, Chia-Man [Department of Surgery, Taichung Veterans General Hospital, Taiwan, ROC (China); National Yang-Ming University, Taipei, Taiwan, ROC (China); Yeh, Chou-Ming, E-mail: cmchou4301@gmail.com [Taichung Hospital, Department of Health, Executive Yuan, Taiwan, ROC (China); Chung, Chi-Jen [Department of Dental Technology and Materials Science, Central Taiwan University of Science and Technology, Taiwan, ROC (China); He, Ju-Liang [Department of Materials Science and Engineering, Feng Chia University, Taiwan, ROC (China)

    2013-09-01

    Plasma-polymerized para-xylene (PPX) was developed in a previous study by adjusting the process parameters: pulse frequency of the power supply (ω{sub p}) and para-xylene monomer flow rate (f{sub p}). All the obtained PPX films exhibit an amorphous structure and present hydrophobicity (water contact angle ranging from 98.5° to 121.1°), higher film growth rate and good fibroblast cell proliferation. In this study, in vitro tests (fibroblast cell compatibility and platelet adhesion) and an in vivo animal study were performed by using PPX deposited industrial-grade silicone sheets (IGS) and compared with medical-grade silicone ones (MS), which were commonly manufactured into catheters or drainage tubes in clinical use. The results reveal that PPX deposited at high ω{sub p} or high f{sub p}, in comparison with MS, exhibit better cell proliferation and clearly shows less cell adhesion regardless of ω{sub p} and f{sub p}. PPX also exhibit a comparatively lower level of platelet adhesion than MS. In the animal study, PPX-coated IGS result in similar local tissue responses at 3, 7 and 28 days (short-term) and 84 days (long-term) after subcutaneous implantation the abdominal wall of rodents compared with respective responses to MS. These results suggest that PPX-coated industrial-grade silicone is one alternative to high cost medical-grade silicone.

  20. Humidity-independent conducting polyaniline films synthesized using advanced atmospheric pressure plasma polymerization with in-situ iodine doping

    Science.gov (United States)

    Park, Choon-Sang; Kim, Do Yeob; Kim, Dong Ha; Lee, Hyung-Kun; Shin, Bhum Jae; Tae, Heung-Sik

    2017-01-01

    This study reports on the synthesis and characterization of conducting polyaniline (PANI) thin films when using advanced atmospheric pressure plasma jets (APPJs). A simple method for synthesizing conducting polymers (CPs) with humidity-independent characteristics is introduced using advanced APPJs and an in-situ iodine doping method. In the case of ex-situ I2 doping, a humidity effect study showed that increasing the relative humidity produced significant changes in the electrical resistance (R) of the PANI, indicating strong humidity-dependent characteristics similar to conventional CPs. In contrast, in the case of in-situ I2 doping, the R and sensitivity of the PANI remained essentially unchanged when increasing the relative humidity, except for a very low sensitivity of 0.5% under 94% relative humidity. In addition, the R for the PANI with in-situ I2 doping showed no aging effect, while the R for the ex-situ-doped PANI increased dramatically over time. Thus, it is anticipated that the use of in-situ doping during plasma polymerization can be widely used to design stable and high-performance CPs with humidity-independent characteristics for a variety of applications.

  1. In vitro cell culture, platelet adhesion tests and in vivo implant tests of plasma-polymerized para-xylene films

    Science.gov (United States)

    Chou, Chia-Man; Yeh, Chou-Ming; Chung, Chi-Jen; He, Ju-Liang

    2013-09-01

    Plasma-polymerized para-xylene (PPX) was developed in a previous study by adjusting the process parameters: pulse frequency of the power supply (ωp) and para-xylene monomer flow rate (fp). All the obtained PPX films exhibit an amorphous structure and present hydrophobicity (water contact angle ranging from 98.5° to 121.1°), higher film growth rate and good fibroblast cell proliferation. In this study, in vitro tests (fibroblast cell compatibility and platelet adhesion) and an in vivo animal study were performed by using PPX deposited industrial-grade silicone sheets (IGS) and compared with medical-grade silicone ones (MS), which were commonly manufactured into catheters or drainage tubes in clinical use. The results reveal that PPX deposited at high ωp or high fp, in comparison with MS, exhibit better cell proliferation and clearly shows less cell adhesion regardless of ωp and fp. PPX also exhibit a comparatively lower level of platelet adhesion than MS. In the animal study, PPX-coated IGS result in similar local tissue responses at 3, 7 and 28 days (short-term) and 84 days (long-term) after subcutaneous implantation the abdominal wall of rodents compared with respective responses to MS. These results suggest that PPX-coated industrial-grade silicone is one alternative to high cost medical-grade silicone.

  2. Up-scaling the production of modified a-C:H coatings in the framework of plasma polymerization processes

    Science.gov (United States)

    Corbella, C.; Bialuch, I.; Kleinschmidt, M.; Bewilogua, K.

    2009-10-01

    Hydrogenated amorphous carbon (a-C:H) films with silicon and oxygen additions, which exhibit mechanical, tribological and wetting properties adequate for protective coating performance, have been synthesized at room temperature in a small- (0.1 m 3) and a large-scale (1 m 3) coaters by low-pressure Plasma-Activated Chemical Vapour Deposition (PACVD). Hence, a-C:H:Si and a-C:H:Si:O coatings were produced in atmospheres of tetramethylsilane (TMS) and hexamethyldisiloxane (HMDSO), respectively, excited either by radiofrequency (RF - small scale) or by pulsed-DC power (large scale). Argon was employed as a carrier gas to stabilize the glow discharge. Several series of 2-5 μm thick coatings have been prepared at different mass deposition rates, Rm, by varying total gas flow, F, and input power, W. Arrhenius-type plots of Rm/ F vs. ( W/ F) -1 show linear behaviours for both plasma reactors, as expected for plasma polymerization processes at moderated energies. The calculation of apparent activation energy, Ea, in each series permitted us to define the regimes of energy-deficient and monomer-deficient PACVD processes as a function of the key parameter W/ F. Moreover, surface properties of the modified a-C:H coatings, such as contact angle, abrasive wear rate and hardness, appear also correlated to this parameter. This work shows an efficient methodology to scale up PACVD processes from small, lab-scale plasma machines to industrial plants by the unique evaluation of macroscopic parameters of deposition.

  3. Properties of N-rich Silicon Nitride Film Deposited by Plasma-Enhanced Atomic Layer Deposition

    Science.gov (United States)

    Jhang, Pei-Ci; Lu, Chi-Pin; Shieh, Jung-Yu; Yang, Ling-Wu; Yang, Tahone; Chen, Kuang-Chao; Lu, Chih-Yuan

    2017-07-01

    An N-rich silicon nitride film, with a lower refractive index (RI) than the stoichiometric silicon nitride (RI = 2.01), was deposited by alternating the exposure of dichlorosilane (DCS, SiH2Cl2) and that of ammonia (NH3) in a plasma-enhanced atomic layer deposition (PEALD) process. In this process, the plasma ammonia was easily decomposed to reactive radicals by RF power activating so that the N-rich silicon nitride was easily formed by excited ammonia radicals. The growth kinetics of N-rich silicon nitride were examined at various deposition temperatures ranging from 400 °C to 630 °C; the activation energy (Ea) decreased as the deposition temperature decreased below 550 °C. N-rich silicon nitride film with a wide range of values of refractive index (RI) (RI = 1.86-2.00) was obtained by regulating the deposition temperature. At the optimal deposition temperature, the effects of RF power, NH3 flow rate and NH3 flow time were on the characteristics of the N-rich silicon nitride film were evaluated. The results thus reveal that the properties of the N-rich silicon nitride film that was formed by under plasma-enhanced atomic layer deposition (PEALD) are dominated by deposition temperature. In charge trap flash (CTF) study, an N-rich silicon nitride film was applied to MAONOS device as a charge-trapping layer. The films exhibit excellent electron trapping ability and favor a fresh cell data retention performance as the deposition temperature decreased.

  4. Plasma polymerization by Softplasma

    DEFF Research Database (Denmark)

    Jiang, J.; Wu, Zhenning; Benter, Maike

    2008-01-01

    as reactive splvent (as shown in Figure 1). 1] H. Biederman, in Plasma Polymer Films. (ed.) H. Biederman. Imperial College Press, Singapore, 13-24 ~OO~· '. , [2] R. d'Agostino et.a!. in Plasma Depd~itiqn, 'Treatment, and Etching ofPolymers. (ed.) R. d'Agostino, Academic Press, U.S. (1990). [3] F. F. Shi......In the late 19th century, the first depositions - known today as plasma polymers, were reported. In the last century, more and more research has been put into plasma polymers. Many different deposition systems have been developed. [1, 2] Shi F. F. broadly classified them into internal electrode......, external electrode, and electrodeless microwave or high frequency reactors. [3] Softplasma™ is an internal electrode plasma setup powered by low frequenc~ gower supply. It was developed in late 90s for surface treatment of silicone rubber. [ ]- 5] It is a low pressure, low electron density, 3D homogenous...

  5. Ethylene glycol blood test

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/article/003564.htm Ethylene glycol blood test To use the sharing features on ... enable JavaScript. This test measures the level of ethylene glycol in the blood. Ethylene glycol is a type ...

  6. Enhanced corrosion resistance and hemocompatibility of biomedical NiTi alloy by atmospheric-pressure plasma polymerized fluorine-rich coating

    Energy Technology Data Exchange (ETDEWEB)

    Li, Penghui; Li, Limin [Department of Physics and Materials Science, City University of Hong Kong, Tat Chee Avenue, Kowloon, Hong Kong (China); Wang, Wenhao [Department of Physics and Materials Science, City University of Hong Kong, Tat Chee Avenue, Kowloon, Hong Kong (China); Division of Spine Surgery, Department of Orthopaedics and Traumatology, Pokfulam, Hong Kong (China); Jin, Weihong [Department of Physics and Materials Science, City University of Hong Kong, Tat Chee Avenue, Kowloon, Hong Kong (China); Liu, Xiangmei [Department of Physics and Materials Science, City University of Hong Kong, Tat Chee Avenue, Kowloon, Hong Kong (China); Ministry of Education Key Laboratory for the Green Preparation and Application of Functional Materials, Hubei University, Wuhan, Hubei 430062 (China); Yeung, Kelvin W.K. [Division of Spine Surgery, Department of Orthopaedics and Traumatology, Pokfulam, Hong Kong (China); Chu, Paul K., E-mail: paul.chu@cityu.edu.hk [Department of Physics and Materials Science, City University of Hong Kong, Tat Chee Avenue, Kowloon, Hong Kong (China)

    2014-04-01

    Highlights: • Fluoropolymer is deposited on NiTi alloy via atmospheric-pressure plasma polymerization. • The corrosion resistance of NiTi alloy in SBF and DMEM is evidently improved. • The adsorption ratio of albumin to fibrinogen is increased on the coated surface. • The reduced platelet adhesion number indicates better in vitro hemocompatibility. - Abstract: To improve the corrosion resistance and hemocompatibility of biomedical NiTi alloy, hydrophobic polymer coatings are deposited by plasma polymerization in the presence of a fluorine-containing precursor using an atmospheric-pressure plasma jet. This process takes place at a low temperature in air and can be used to deposit fluoropolymer films using organic compounds that cannot be achieved by conventional polymerization techniques. The composition and chemical states of the polymer coatings are characterized by fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). The corrosion behavior of the coated and bare NiTi samples is assessed and compared by polarization tests and electrochemical impedance spectroscopy (EIS) in physiological solutions including simulated body fluids (SBF) and Dulbecco's Modified Eagle's medium (DMEM). The corrosion resistance of the coated NiTi alloy is evidently improved. Protein adsorption and platelet adhesion tests reveal that the adsorption ratio of albumin to fibrinogen is increased and the number of adherent platelets on the coating is greatly reduced. The plasma polymerized coating renders NiTi better in vitro hemocompatibility and is promising as a protective and hemocompatible coating on cardiovascular implants.

  7. Improved Bone Formation in Osteoporotic Rabbits with the Bone Morphogenetic Protein-2 (rhBMP-2 Coated Titanium Screws Which Were Coated By Using Plasma Polymerization Technique

    Directory of Open Access Journals (Sweden)

    Salih Gulsen

    2014-06-01

    Full Text Available Delaying of bone fusion in osteoporotic patients underwent spinal stabilization surgery leads to screw loosening, and this causes pseudoarticulation, mobility and fibrosis at vertebral segments. To prevent these complications, the screws coated with recombinant bone morphogenetic protein-2 (rhBMP-2 could be used. To verify this hypothesis, we coated 5 Titanium screws with rhBMP-2 using plasma polymerization method, and also used 10 uncoated screws for making comparison between coated and uncoated screws in different groups. And 15 skeletally mature white New Zealand female rabbits were assigned into three different groups: Group 1(N = 5: No osteoporosis induction and insertion of uncoated Titanium screw into right sacrum of each rabbit in group 1; group 2 (N = 5: Osteoporosis induction and insertion of uncoated Titanium screw into right sacrum of each rabbit in group 2; group 3 (N = 5 rhBMP-2 coated Titanium screw inserted into right sacrum of each rabbit in group 3. In summary, using of these coated screws provides new bone formation, but causes less fibrosis and less inflammation than uncoated screws at the interface between the coated screw and bone. Then the plasma polymerization technique provides controlled releasing of rhBMP-2 from the screw to the bone tissue in osteoporotic rabbits.

  8. Gallic acid tailoring surface functionalities of plasma-polymerized allylamine-coated 316L SS to selectively direct vascular endothelial and smooth muscle cell fate for enhanced endothelialization.

    Science.gov (United States)

    Yang, Zhilu; Xiong, Kaiqin; Qi, Pengkai; Yang, Ying; Tu, Qiufen; Wang, Jin; Huang, Nan

    2014-02-26

    The creation of a platform for enhanced vascular endothelia cell (VEC) growth while suppressing vascular smooth muscle cell (VSMC) proliferation offers possibility for advanced coatings of vascular stents. Gallic acid (GA), a chemically unique phenolic acid with important biological functions, presents benefits to the cardiovascular disease therapy because of its superior antioxidant effect and a selectivity to support the growth of ECs more than SMCs. In this study, GA was explored to tailor such a multifunctional stent surface combined with plasma polymerization technique. On the basis of the chemical coupling reaction, GA was bound to an amine-group-rich plasma-polymerized allylamine (PPAam) coating. The GA-functionalized PPAam (GA-PPAam) surface created a favorable microenvironment to obtain high ECs and SMCs selectivity. The GA-PPAam coating showed remarkable enhancement in the adhesion, viability, proliferation, migration, and release of nitric oxide (NO) of human umbilical vein endothelial cells (HUVECs). The GA-PPAam coating also resulted in remarkable inhibition effect on human umbilical artery smooth muscle cell (HUASMC) adhesion and proliferation. These striking findings may provide a guide for designing the new generation of multifunctional vascular devices.

  9. Surface Modification of Fillers and Curatives by Plasma Polymerization for Enhanced Performance of Single Rubbers and Dissimilar Rubber/Rubber Blends

    Science.gov (United States)

    Noordermeer, J. W. M.; Datta, R. N.; Dierkes, W. K.; Guo, R.; Mathew, T.; Talma, A. G.; Tiwari, M.; van Ooij, W.

    Plasma polymerization is a technique for modifying the surface characteristics of fillers and curatives for rubber from essentially polar to nonpolar. Acetylene, thiophene, and pyrrole are employed to modify silica and carbon black reinforcing fillers. Silica is easy to modify because its surface contains siloxane and silanol species. On carbon black, only a limited amount of plasma deposition takes place, due to its nonreactive nature. Oxidized gas blacks, with larger oxygen functionality, and particularly carbon black left over from fullerene production, show substantial plasma deposition. Also, carbon/silica dual-phase fillers react well because the silica content is reactive. Elemental sulfur, the well-known vulcanization agent for rubbers, can also be modified reasonably well.

  10. [Direct biosynthesis of ethylene].

    Science.gov (United States)

    Sun, Zhilan; Chen, Yifeng

    2013-10-01

    Ethylene is the most widely used petrochemical feedstock globally. The development of bio-ethylene is essential due to limited fossil fuels and rising oil prices. Bio-ethylene is produced primarily by the dehydration of ethanol, but can alternatively be directly produced from ethylene biosynthesis pathways in plants, algae, or microorganisms by using cheap and renewable substrates. This review addressed the biosynthesis of ethylene in plants and microorganisms, the characterization of key enzymes, genetic engineering strategies for ethylene biosynthesis in microorganisms, and evaluated its perspective and successful cases toward the industrial application. The direct production of bio-ethylene from a biological process in situ is promising to supplement and even replace the petrochemical ethylene production.

  11. Valence band hybridization in N-rich GaN1-xAsx alloys

    Energy Technology Data Exchange (ETDEWEB)

    Wu, J.; Walukiewicz, W.; Yu, K.M.; Denlinger, J.D.; Shan, W.; Ager III, J.W.; Kimura, A.; Tang, H.F.; Kuech, T.F.

    2004-05-04

    We have used photo-modulated transmission and optical absorption spectroscopies to measure the composition dependence of interband optical transitions in N-rich GaN{sub 1-x}As{sub x} alloys with x up to 0.06. The direct bandgap gradually decreases as x increases. In the dilute x limit, the observed band gap approaches 2.8 eV; this limiting value is attributed to a transition between the As localized level, which has been previously observed in As-doped GaN at 0.6 eV above the valence band maximum in As-doped GaN, and the conduction band minimum. The structure of the valence band of GaN{sub 1-x}As{sub x} is explained by the hybridization of the localized As states with the extended valence band states of GaN matrix. The hybridization is directly confirmed by soft x-ray emission experiments. To describe the electronic structure of the GaN{sub 1-x}As{sub x} alloys in the entire composition range a linear interpolation is used to combine the effects of valence band hybridization in N-rich alloys with conduction band anticrossing in As-rich alloys.

  12. The N-rich Mass Donor Star of the Microquasar LS 5039

    CERN Document Server

    McSwain, M V; Huang, W; Wiita, P J; Wingert, D W; Kaper, L

    2003-01-01

    We present an investigation of new optical and ultraviolet spectra of the mass donor star in the massive X-ray binary LS 5039. The optical band spectral line strengths indicate that the atmosphere is N-rich and C-poor, and we classify the stellar spectrum as type ON6.5 V((f)). The N-strong and C-weak pattern is also found in the stellar wind P Cygni lines of N V 1240 and C IV 1550. We suggest that the N-enrichment may result from internal mixing if the O-star was born as a rapid rotator, or the O-star may have accreted N-rich gas during a common envelope interaction with the progenitor of the supernova. We re-evaluated the orbital elements to find an orbital period of P=4.4267 +/- 0.0010 d. We compared the spectral line profiles with new non-LTE, line-blanketed model spectra, from which we derive an effective temperature T_eff = 37.5 +/- 1.7 kK, gravity log g = 4.0 +/- 0.1, and projected rotational velocity V sin i = 140 +/- 8 km/s. We fit the UV, optical, and IR flux distribution using a model spectrum and e...

  13. The covalent immobilization of heparin to pulsed-plasma polymeric allylamine films on 316L stainless steel and the resulting effects on hemocompatibility.

    Science.gov (United States)

    Yang, Zhilu; Wang, Jin; Luo, Rifang; Maitz, Manfred F; Jing, Fengjuan; Sun, Hong; Huang, Nan

    2010-03-01

    For an improved hemocompatibility of 316L stainless steel (SS), we develop a facile and effective approach to fabricating a pulsed-plasma polymeric allylamine (P-PPAm) film that possesses a high cross-linking degree and a high density of amine groups, which is used for subsequent bonding of heparin. The P-PPAm film as a stent coating shows good resistance to the deformation behavior of compression and expansion of a stent. Using deionized water as an aging medium, it is demonstrated that the heparin-immobilized P-PPAm (Hep-P-PPAm) surface has a good retention of heparin. The systematic in vitro hemocompatibility evaluation reveals lower platelet adhesion, platelet activation and fibrinogen activation on the Hep-P-PPAm surface, and the activated partial thromboplastin time prolongs for about 15 s compared with 316L SS. The P-PPAm surface significantly promotes adhesion and proliferation of endothelial cells (ECs). For the Hep-P-PPAm, although EC adhesion and proliferation is slightly suppressed initially, after cultivation for 3 days, the growth behavior of ECs is remarkably improved over 316L SS. In vivo results indicate that the Hep-P-PPAm surface successfully restrain thrombus formation by growing a homogeneous and intact shuttle-like endothelium on its surface. The Hep-P-PPAm modified 316L SS shows a promising application for vascular devices.

  14. Ethylene insensitive plants

    Science.gov (United States)

    Ecker, Joseph R.; Nehring, Ramlah; McGrath, Robert B.

    2007-05-22

    Nucleic acid and polypeptide sequences are described which relate to an EIN6 gene, a gene involved in the plant ethylene response. Plant transformation vectors and transgenic plants are described which display an altered ethylene-dependent phenotype due to altered expression of EIN6 in transformed plants.

  15. Ethylene, seed germination, and epinasty.

    Science.gov (United States)

    Stewart, E R; Freebairn, H T

    1969-07-01

    Ethylene activity in lettuce seed (Lactuca satina) germination and tomato (Lycopersicon esculentum) petiole epinasty has been characterized by using heat to inhibit ethylene synthesis. This procedure enabled a separation of the production of ethylene from the effect of ethylene. Ethylene was required in tomato petioles to produce the epinastic response and auxin was found to be active in producing epinasty through a stimulation of ethylene synthesis with the resulting ethylene being responsible for the epinasty. In the same manner, it was shown that gibberellic acid stimulated ethylene synthesis in lettuce seeds. The ethylene produced then in turn stimulated the seeds to germinate. It was hypothesized that ethylene was the intermediate which caused epinasty or seed germination. Auxin and gibberellin primarily induced their response by stimulating ethylene production.

  16. Study of the adhesive properties versus stability/aging of hernia repair meshes after deposition of RF activated plasma polymerized acrylic acid coating

    Energy Technology Data Exchange (ETDEWEB)

    Rivolo, Paola [Politecnico di Torino, Department of Applied Science and Technology, C.so Duca degli Abruzzi 24, 10129 Torino (Italy); Nisticò, Roberto, E-mail: roberto.nistico@unito.it [University of Torino, Department of Chemistry and NIS Centre, Via P. Giuria 7, 10125 Torino (Italy); Barone, Fabrizio [University of Torino, Department of Chemistry and NIS Centre, Via P. Giuria 7, 10125 Torino (Italy); Faga, Maria Giulia; Duraccio, Donatella [CNR-IMAMOTER, Strada delle Cacce 73, 10135 Torino (Italy); Martorana, Selanna [Herniamesh S.r.l., Via F.lli Meliga 1/C, 10034 Chivasso (Italy); Ricciardi, Serena [Politecnico di Torino, Department of Applied Science and Technology, C.so Duca degli Abruzzi 24, 10129 Torino (Italy); Magnacca, Giuliana [University of Torino, Department of Chemistry and NIS Centre, Via P. Giuria 7, 10125 Torino (Italy)

    2016-08-01

    In order to confer adhesive properties to commercial polypropylene (PP) meshes, a surface plasma-induced deposition of poly-(acrylic acid) (PPAA) is performed. Once biomaterials were functionalized, different post-deposition treatments (i.e. water washing and/or thermal treatments) were investigated with the aim of monitoring the coating degradation (and therefore the loss of adhesion) after 3 months of aging in both humid/oxidant (air) and inert (nitrogen) atmospheres. A wide physicochemical characterization was carried out in order to evaluate the functionalization effectiveness and the adhesive coating homogeneity by means of static water drop shape analysis and several spectroscopies (namely, FTIR, UV–Visible and X-ray Photoemission Spectroscopy). The modification of the adhesion properties after post-deposition treatments as well as aging under different storage atmospheres were investigated by means of Atomic Force Microscopy (AFM) used in Force/Distance (F/D) mode. This technique confirms itself as a powerful tool for unveiling the surface adhesion capacity as well as the homogeneity of the functional coatings along the fibers. Results obtained evidenced that post-deposition treatments are mandatory in order to remove all oligomers produced during the plasma-treatment, whereas aging tests evidenced that these devices can be simply stored in presence of air for at least three months without a meaningful degradation of the original properties. - Highlights: • Plasma polymerized surface functionalization of hernia-repair meshes was used to confer adhesive properties. • The stability of the adhesive coating was verified under different post-deposition conditions. • The use of AFM in F/D mode was selected to monitor the coating degradation.

  17. A Highly Energetic N-Rich Zeolite-Like Metal-Organic Framework with Excellent Air Stability and Insensitivity.

    Science.gov (United States)

    Qin, Jun-Sheng; Zhang, Ji-Chuan; Zhang, Min; Du, Dong-Ying; Li, Jing; Su, Zhong-Min; Wang, Yuan-Yuan; Pang, Si-Ping; Li, Sheng-Hua; Lan, Ya-Qian

    2015-12-01

    A stable N-rich aromatic ligand is employed to prepare energetic zeolite-like metal-organic frameworks. IFMC-1 shows excellent air stability, and the lowest sensitivity toward impact, friction, and electrostatic discharge and the highest predicted heat of detonation among the reported coordination polymers, and even commercial materials (such as trinitrotoluene (TNT)).

  18. Hydrophobicity attainment and wear resistance enhancement on glass substrates by atmospheric plasma-polymerization of mixtures of an aminosilane and a fluorocarbon

    Science.gov (United States)

    Múgica-Vidal, Rodolfo; Alba-Elías, Fernando; Sainz-García, Elisa; Pantoja-Ruiz, Mariola

    2015-08-01

    Mixtures of different proportions of two liquid precursors were subjected to plasma-polymerization by a non-thermal atmospheric jet plasma system in a search for a coating that achieves a hydrophobic character on a glass substrate and enhances its wear resistance. 1-Perfluorohexene (PFH) was chosen as a low-surface-energy precursor to promote a hydrophobic character. Aminopropyltriethoxysilane (APTES) was chosen for its contribution to the improvement of wear resistance by the formation of siloxane bonds. The objective of this work was to determine which of the precursors' mixtures that were tested provides the coating with the most balanced enhancement of both hydrophobicity and wear resistance, given that coatings deposited with fluorocarbon-based precursors such as PFH are usually low in resistance to wear and coatings deposited with APTES are generally hydrophilic. The coatings obtained were analyzed by Scanning Electron Microscopy (SEM), Atomic Force Microscopy (AFM), Fourier Transform Infra-Red (FTIR) spectroscopy, X-ray Photoelectron Spectroscopy (XPS), static Water Contact Angle (WCA) measurements, tribological ball-on-disc tests and contact profilometry. A relationship between the achievement of a hydrophobic character and the modifications to roughness and surface morphology and the incorporation of fluorocarbon groups in the surface chemistry was observed. Also, it was seen that the wear resistance was influenced by the SiOSi content of the coatings. In turn, the SiOSi content appears to be directly related to the percentage of APTES used in the mixture of precursors. The best conjunction of hydrophobicity and wear resistance in this work was found in the sample that was coated using a mixture of APTES and PFH in proportions of 75 and 25%, respectively. Its WCA (100.2 ± 7.5°) was the highest of all samples that were measured and more than three times that of the uncoated glass (31 ± 0.7°). This sample underwent a change from a hydrophilic to a

  19. Monocyte/macrophage and protein interactions with non-fouling plasma polymerized tetraglyme and chemically modified polystyrene surfaces: In vitro and in vivo studies

    Science.gov (United States)

    Shen, Mingchao

    2001-07-01

    Biomaterials become encapsulated by fibrous tissues after implantation in soft tissues. Monocytes and macrophages are believed to play important roles in this response. The hypothesis tested in this dissertation is that material surface chemistry determines the amount of adsorbed proteins, which mediate monocyte adhesion, activation, and the foreign body response. On chemically modified polystyrene surfaces, monocyte adhesion in vitro was promoted by preadsorbed fibrinogen, fibronectin, and IgG, and increased with increasing amount of adsorbed fibrinogen. Adsorbed proteins and material surface chemistry mediated monocyte activation. TNFalpha release, procoagulant activity, and multinucleated foreign body giant cell (FBGC) formation was at least two-fold higher on IgG than other protein adsorbed surfaces. Adsorbed IgG and fibrinogen triggered monocyte intracellular calcium changes. FBGC formation was the highest on the hydrophobic polystyrene surface. Materials that greatly reduce non-specific protein adsorption may reduce the foreign body response to implanted materials. Radio-frequency plasma polymerized tetraglyme (CH3O(CH2CH2O)4CH 3) surfaces contained PEO-like chemical species and reduced fibrinogen adsorption to less than 10 ng/cm2. Monocyte adhesion to tetraglyme in vitro was also greatly reduced. Monocyte adhesion correlated linearly to the amount of adsorbed fibrinogen on a series of tetraglyme surfaces deposited at different plasma powers. Multivariate analysis using partial least squares regression identified the key surface spectra variables from electron spectroscopy for chemical analysis (ESCA) and time of flight secondary ion mass spectrometry (ToF-SIMS) that contributed to the non-fouling properties of tetraglyme. However, leukocyte adhesion to surfaces implanted subcutaneously in mice for 1 or 28 days did not correlate with protein adsorption and was higher on tetraglyme than the FEP control. Fibrous encapsulation to tetraglyme implanted for 28 days

  20. Ejecta of Eta Carinae: What We Learn about N-Rich Chemistry

    Science.gov (United States)

    Gull, Theodore

    2006-01-01

    At least one member of the binary system, Eta Carinae, is in the late stages of CNO-cycle. At least ten solar masses of ejecta make up the Homunculus, a neutral bi-polar shell ejected in the 1840s and the Little Homunculus, an internal, ionized bi-polar shell ejected in the 1890s. HST/STIS and VLTAJVES high dispersion spectroscopy revealed absorptions of multiple elements and diatomic molecules in these shells, some, such as V II and Sr II have not been seen previously in the ISM. The skirt region between the bi-lobes includes the very bright Weigelt blobs, within 0.1 to 0.3" of the central source, and the more distant, unusual Strontium Filament, a neutral emission nebula photoexcited by Balmer continuum, but shielded by Fe II from Lyman radiation. The 600+ emission lines are due to metals usually tied up in dust, but underabundances of C and O prevent precipitation as oxides onto the dust grains. Indications are that Ti/Ni is 100X solar, likely due not to nuclear processing, but the very different photo-excitation environments coupled with N-rich, C-, O-poor chemistry. In the Homunculus, level populations of the molecules indicate 60K gas; the metal absorption lines, 760K; that of the Little Homunculus 6400K during the broad spectroscopic maximum, relaxing to 5000K for the few month long minimum. Lyman radiation, including both continuum and Lyman lines, is trapped across periastron. leading to temporary relaxation of the ejecta. These ejecta are a treasure trove of information on material thrown out of massive stars in the CNO-cycle, well before the helium burning phase. Curiously, spectra of three very recent SWIFT GRBs indicate the presence of warm, photoexcited ejecta in the vicinity of the protoGRBs, but obviously of very different abundances. However, the ejecta of Eta Carinae promise to be a nearby example of massive ejecta, the study of which should lead to increased insight of earlier, very distant massive stars.

  1. Free-carrier contribution to the optical response of N-rich Cu{sub 3}N thin films

    Energy Technology Data Exchange (ETDEWEB)

    Gordillo, N; Agullo-Lopez, F [Centro de Microanalisis de Materiales, Universidad Autonoma de Madrid 28049-Madrid (Spain); Gonzalez-Arrabal, R [Instituto de Microelectronica de Madrid CSIC C/ Isaac Newton, 8. Tres Cantos, 28760-Madrid (Spain); Alvarez-Herrero, A, E-mail: nuria.gordillo@uam.e [Laboratorio de Instrumentacion Espacial, INTA, Torrejon de Ardoz, 28850-Madrid (Spain)

    2009-08-21

    The influence of nitrogen excess on the optical response of N-rich Cu{sub 3}N films is reported. The optical spectra measured in the wavelength range from 0.30 to 20.00 {mu}m have been correlated with the elemental film composition which can be adjusted in the nitrogen atomic percentage (at%) range from 27 {+-} 2 up to 33 {+-} 2. The absorption spectra for the N-rich films are consistent with direct optical transitions corresponding to the stoichiometric semiconductor Cu{sub 3}N plus a free-carrier contribution that can be tuned in accordance with the N-excess. The data are consistent with the incorporation of the excess N in the lattice as an electron acceptor that generates free holes.

  2. DEVELOPMENT TREND OF ETHYLENE INDUSTRY

    Institute of Scientific and Technical Information of China (English)

    Song Ting

    2014-01-01

    The growth of world ethylene production and demand has been slowed down, but accelarated growth after 2015 is forecasted. Shale gas revolution has promoted the resurge of ethylene industry in North America and changed the investment pattern of world ethylene industry.Chinese ethylene industry has developed rapidly, facing not only opportunities for development but also outside pressure.The diversified pattern of Chinese ethylene industry has been formed , in which MTO has become an effective complement to the ethylene industry.While cracking raw material has become lighter and lighter worldwide, naphtha still dominates the ethylene raw material in China, leading to high cost of raw material.Aiming to reduce the cost and improve the competitiveness, this article introduces the progress of steam cracking technology for ethylene production from the aspects of low energy consumption , low cost, large capacity and long-term operation.

  3. AUXIN STIMULATION OF ETHYLENE EVOLUTION

    Science.gov (United States)

    mechanism of auxin action on the enhancement of ethylene production is the formation of enzymes involved in ethylene biogenesis....The stimulation of ethylene production by auxin was inhibited by actinomycin D and other inhibitors of protein synthesis. It is concluded that the

  4. Ethylene production by apple protoplasts.

    Science.gov (United States)

    Anderson, J D; Lieberman, M; Stewart, R N

    1979-05-01

    Freshly prepared protoplasts from apple tissue that produced ethylene were obtained. Ethylene production was inhibited by osmotic shock, 0.01% Triton X-100, and aminoethoxyvinyl glycine. Protoplasts as well as the ethylene system were not greatly affected by protease treatment.

  5. $\\gamma$- spectroscopy of n-rich $^{95,96}$Rb nuclei by the incomplete fusion reaction of $^{94}$Kr on $^{7}$Li: Introduction to HIE-ISOLDE studies of n-rich Sb and Tl isotopes with Sn and Hg radioactive beams.

    CERN Document Server

    Fornal, B; Bednarczyk, P; Cieplicka, N; Krolas, W; Maj, A; Leoni, S; Benzoni, G; Blasi, N; Bottoni, S; Bracco, A; Camera, F; Crespi, F; Million, B; Morales, A; Wieland, O; Rusek, K; Lunardi, S; Mengoni, D; Recchia, F; Ur, CA; Valiente-Dobon, J; de France, G; Clement, E; Elseviers, J; Flavigny, F; Huyse, M; Raabe, R; Sambi, S; Van Duppen, P; Sferrazza, M; Simpson, G; Georgiev, G; Sotty, C; Blazhev, A; German, R; Siebeck, B; Seidlitz, M; Reiter, P; Warr, N; Boenig, S; Ilieva, S; Kroell, T; Scheck, M; Thurauf, M; Gernhaeuser, R; Mucher, D; Janssens, R; Carpenter, MP; Zhu, S; Marginean, NM; Balabanski, D; Kowalska, M

    2012-01-01

    $\\gamma$- spectroscopy of n-rich $^{95,96}$Rb nuclei by the incomplete fusion reaction of $^{94}$Kr on $^{7}$Li: Introduction to HIE-ISOLDE studies of n-rich Sb and Tl isotopes with Sn and Hg radioactive beams.

  6. Ultrathin MoS2 sheets supported on N-rich carbon nitride nanospheres with enhanced lithium storage properties

    Science.gov (United States)

    Chenrayan, Senthil; Chandra, Kishore S.; Manickam, Sasidharan

    2017-07-01

    Deciphering the structural and volume changes occurring during electrode reactions in lithium-ion batteries is perhaps a boon for high energy density batteries. Here, we report the synthesis of 3D network of dichalcogenide molybdenum disulfide (MoS2) encapsulated over nitrogen rich graphitic carbon nitride nanosphere (g-C3N4) forming an interconnected and uniform g-C3N4/MoS2 scaffolds. The crystallinity, phase purity, morphological features and elemental composition were evaluated through XRD, FESEM, TEM, HRTEM, BET and XPS analyses. The electrochemical properties of N-rich g-C3N4/MoS2 scaffolds were investigated as potential anode materials for lithium-ion batteries. Electrochemical testing of the g-C3N4/MoS2 constructured electrode delivered reversible capacity of 857 mAh g-1at 0.1 C rate after fifty cycles and exhibited a high rate performance with reversible capacity of 383 mAh g-1 at 10 C rate (higher than theoretical capacity of graphite, 372 mAh g-1). The superior electrochemical property of g-C3N4/MoS2 is attributed to N-rich carbon support which favors better electronic conductivity, and affords more sites for Li+ ions. The nitrogen rich carbon nitride accommodates volume changes caused during repeated charge/discharges and maintains high structural integrity and specific capacity.

  7. Interstellar Antifreeze: Ethylene Glycol

    Science.gov (United States)

    Hollis, J. M.; Lovas, F. J.; Jewell, P. R.; Coudert, L. H.

    2002-01-01

    Interstellar ethylene glycol (HOCH2CH2,OH) has been detected in emission toward the Galactic center source Sagittarius B2(N-LMH) by means of several millimeter-wave rotational torsional transitions of its lowest energy conformer. The types and kinds of molecules found to date in interstellar clouds suggest a chemistry that favors aldehydes and their corresponding reduced alcohols-e.g., formaldehyde (H2CO)/methanol (CH3OH), acetaldehyde (CH3CHO)/ethanol (CH3CH2OH). Similarly, ethylene glycol is the reduced alcohol of glycolaldehyde (CH2OHCHO), which has also been detected toward Sgr B2(N-LMH). While there is no consensus as to how any such large complex molecules are formed in the interstellar clouds, atomic hydrogen (H) and carbon monoxide (CO) could form formaldehyde on grain surfaces, but such surface chemistry beyond that point is uncertain. However, laboratory experiments have shown that the gas-phase reaction of atomic hydrogen (H) and solid-phase CO at 10-20 K can produce formaldehyde and methanol and that alcohols and other complex molecules can be synthesized from cometary ice analogs when subject to ionizing radiation at 15 K. Thus, the presence of aldehyde/ reduced alcohol pairs in interstellar clouds implies that such molecules are a product of a low-temperature chemistry on grain surfaces or in grain ice mantles. This work suggests that aldehydes and their corresponding reduced alcohols provide unique observational constraints on the formation of complex interstellar molecules.

  8. Investigation of localization effect in GaN-rich InGaN alloys and modified band-tail model

    Indian Academy of Sciences (India)

    Chuan-Zhen Zhao; Bin Liu; De-Yi Fu; Hui Chen; Ming Li; Xiang-Qian Xiu; Zi-Li Xie; Shu-Lin Gu; You-Dou Zheng

    2013-08-01

    The temperature-dependent PL properties of GaN-rich InGa1−N alloys is investigated and -shaped temperature dependence is observed in all InGaN samples. It is found that the origin of localization effect in samples A and B are different from that in sample C. For samples A and B, In content fluctuations should be the origin of localization effect, while the localization effect can be attributed to In-rich clusters and metallic indium inclusions for sample C. In addition, the band-tail model is modified and the modified band-tail model is used to investigate the degree of localization effect in the three samples.

  9. Triazine containing N-rich microporous organic polymers for CO2 capture and unprecedented CO2/N2 selectivity

    Science.gov (United States)

    Bhunia, Subhajit; Bhanja, Piyali; Das, Sabuj Kanti; Sen, Tapas; Bhaumik, Asim

    2017-03-01

    Targeted synthesis of microporous adsorbents for CO2 capture and storage is very challenging in the context of remediation from green house gases. Herein we report two novel N-rich microporous networks SB-TRZ-CRZ and SB-TRZ-TPA by extensive incorporation of triazine containing tripodal moiety in the porous polymer framework. These materials showed excellent CO2 storage capacities: SB-TRZ-CRZ displayed the CO2 uptake capacity of 25.5 wt% upto 1 bar at 273 K and SB-TRZ-TPA gave that of 16 wt% under identical conditions. The substantial dipole quadruple interaction between network (polar triazine) and CO2 boosts the selectivity for CO2/N2. SB-TRZ-CRZ has this CO2/N2 selectivity ratio of 377, whereas for SB-TRZ-TPA it was 97. Compared to other porous polymers, these materials are very cost effective, scalable and very promising material for clean energy application and environmental issues.

  10. Chemical tagging with APOGEE: discovery of a large population of N-rich stars in the inner Galaxy

    Science.gov (United States)

    Schiavon, Ricardo P.; Zamora, Olga; Carrera, Ricardo; Lucatello, Sara; Robin, A. C.; Ness, Melissa; Martell, Sarah L.; Smith, Verne V.; García-Hernández, D. A.; Manchado, Arturo; Schönrich, Ralph; Bastian, Nate; Chiappini, Cristina; Shetrone, Matthew; Mackereth, J. Ted; Williams, Rob A.; Mészáros, Szabolcs; Allende Prieto, Carlos; Anders, Friedrich; Bizyaev, Dmitry; Beers, Timothy C.; Chojnowski, S. Drew; Cunha, Katia; Epstein, Courtney; Frinchaboy, Peter M.; García Pérez, Ana E.; Hearty, Fred R.; Holtzman, Jon A.; Johnson, Jennifer A.; Kinemuchi, Karen; Majewski, Steven R.; Muna, Demitri; Nidever, David L.; Nguyen, Duy Cuong; O'Connell, Robert W.; Oravetz, Daniel; Pan, Kaike; Pinsonneault, Marc; Schneider, Donald P.; Schultheis, Matthias; Simmons, Audrey; Skrutskie, Michael F.; Sobeck, Jennifer; Wilson, John C.; Zasowski, Gail

    2017-02-01

    Formation of globular clusters (GCs), the Galactic bulge, or galaxy bulges in general is an important unsolved problem in Galactic astronomy. Homogeneous infrared observations of large samples of stars belonging to GCs and the Galactic bulge field are one of the best ways to study these problems. We report the discovery by APOGEE (Apache Point Observatory Galactic Evolution Experiment) of a population of field stars in the inner Galaxy with abundances of N, C, and Al that are typically found in GC stars. The newly discovered stars have high [N/Fe], which is correlated with [Al/Fe] and anticorrelated with [C/Fe]. They are homogeneously distributed across, and kinematically indistinguishable from, other field stars within the same volume. Their metallicity distribution is seemingly unimodal, peaking at [Fe/H] ˜ -1, thus being in disagreement with that of the Galactic GC system. Our results can be understood in terms of different scenarios. N-rich stars could be former members of dissolved GCs, in which case the mass in destroyed GCs exceeds that of the surviving GC system by a factor of ˜8. In that scenario, the total mass contained in so-called `first-generation' stars cannot be larger than that in `second-generation' stars by more than a factor of ˜9 and was certainly smaller. Conversely, our results may imply the absence of a mandatory genetic link between `second-generation' stars and GCs. Last, but not least, N-rich stars could be the oldest stars in the Galaxy, the by-products of chemical enrichment by the first stellar generations formed in the heart of the Galaxy.

  11. Biochemical changes and GHG emissions during composting of lignocellulosic residues with different N-rich by-products.

    Science.gov (United States)

    Cayuela, Maria Luz; Sánchez-Monedero, Miguel Angel; Roig, Asunción; Sinicco, Tania; Mondini, Claudio

    2012-06-01

    Nitrogen availability plays a critical role in the biodegradation of organic matter during composting. Although the optimal initial C/N is known to be around 25-30, the chemical form in which N is present influences microbial activity and therefore degradation rate and gaseous losses. This study was conducted to evaluate the influence of N availability on the composting of a mixture of lignocellulosic materials. Three composting piles were made of a mixture of wheat straw and cotton waste, each pile containing different N-rich animal by-products. The evolution of the main physico-chemical parameters was monitored (temperature, pH, electrical conductivity, C/N, NH(4)(+), NO(3)(-), water soluble C and N) as well as the enzymatic activity related to the cycle of the main nutrients (β-glucosidase, protease, alkaline phosphatase and fluorescein diacetate hydrolysis). Additionally, fluxes of CO(2), CH(4) and N(2)O emitted from the composting piles were measured by the closed-chamber technique. Cumulative CO(2) emissions were fitted to five different kinetic models with biological significance to C mineralization data. The application of the different N-rich residues had a significant effect on the C and N dynamics during composting. However, most enzymatic activities followed similar patterns in the three piles. The major CO(2) fluxes were recorded during the thermophilic phase, showing a direct relationship with temperature peaks. No CH(4) fluxes were detected for any of the composting piles during the whole trial, whereas low N(2)O emissions were found at the early beginning and during the maturation stage.

  12. Ethylene oxide potential toxicity.

    Science.gov (United States)

    da Cunha Mendes, Gisela Cristina; da Silva Brandão, Teresa Ribeiro; Miranda Silva, Cristina Luisa

    2008-05-01

    The future of ethylene oxide (EO) sterilization has been questioned, owing to its associated toxicity. EO has been around for more than 60 years, mainly due to its recognized characteristics of reliability and effectiveness, coupled with the process flexibility, as well as its compatibility with most mechanical devices. Despite the well-known EO toxicity, the undesirable effects of medical devices' EO residues on the patient's health have not yet been well established. There are limitations related to the current risk-assessment studies. To overcome these drawbacks, demands on greater safety are increasing, which lead to improvements in sterilizers and aeration equipment, as well as the design of the processes. The paper under evaluation highlights risks related to EO sterilization of materials used during processing of stem cells for transplantation, but is an example of a study where the dose of the residues in the devices is not considered.

  13. Quantum Entropic Ambiguities: Ethylene

    CERN Document Server

    Balachandran, A P; Vaidya, S

    2013-01-01

    In a quantum system, there may be many density matrices associated with a state on an algebra of observables. For each density matrix, one can compute its entropy. These are in general different. Therefore one reaches the remarkable possibility that there may be many entropies for a given state [Private communication from R. Sorkin]. This ambiguity in entropy can often be traced to a gauge symmetry emergent from the non-trivial topological character of the configuration space of the underlying system. It can also happen in finite-dimensional matrix models. In the present work, we discuss this entropy ambiguity and its consequences for an ethylene molecule. This is a very simple and well-known system where these notions can be put to tests. Besides its intrinsic conceptual interest, the simplicity of this model can serve as an introduction to a similar discussion of systems such as coloured monopoles and the breaking of colour symmetry.

  14. Mortality among ethylene oxide workers.

    Science.gov (United States)

    Morgan, R W; Claxton, K W; Divine, B J; Kaplan, S D; Harris, V B

    1981-11-01

    Because of reports linking an increased risk of leukemia with exposure to ethylene oxide, a mortality study of workers with potential exposure to ethylene oxide at the Texaco Chemical Company Plant in Port Neches, Tex., was undertaken. A total of 767 males with potential exposure to ethylene oxide were identified. Forty-six deaths occurred in this cohort with 80 expected (standardized mortality ratio; SMR = 58). No deaths from leukemia were seen, nor were there any statistically significant excesses from any specific causes of death.

  15. Crystal structures of ethylene glycol and ethylene glycol monohydrate.

    Science.gov (United States)

    Fortes, A Dominic; Suard, Emmanuelle

    2011-12-21

    We have carried out a neutron powder diffraction study of deuterated ethylene glycol (1,2-ethanediol), and deuterated ethylene glycol monohydrate with the D2B high-resolution diffractometer at the Institut Laue-Langevin. Using these data, we have refined the complete structure, including all hydrogen atoms, of the anhydrous phase at 220 K. In addition, we have determined the structure of ethylene glycol monohydrate at 210 K using direct space methods. Anhydrous ethylene glycol crystallizes in space-group P2(1)2(1)2(1) with four formula units in a unit-cell of dimensions a = 5.0553(1) Å, b = 6.9627(1) Å, c = 9.2709(2) Å, and V = 326.319(8) Å(3) [ρ(calc)(deuterated) = 1386.26(3) kg m(-3)] at 220 K. Ethylene glycol monohydrate crystallizes in space-group P2(1)/c with four formula units in a unit-cell of dimensions a = 7.6858(3) Å, b = 7.2201(3) Å, c = 7.7356(4) Å, β = 92.868(3)°, and V = 428.73(2) Å(3) [ρ(calc)(deuterated) = 1365.40(7) kg m(-3)] at 210 K. Both the structures are characterized by the gauche conformation of the ethylene glycol molecule; however, the anhydrous phase contains the tGg' rotamer (or its mirror, g'Gt), whereas the monohydrate contains the gGg' rotamer. In the monohydrate, each water molecule is tetrahedrally coordinated, donating two hydrogen bonds to, and accepting two hydrogen bonds from the hydroxyl groups of neighboring ethylene glycol molecules. There are substantial differences in the degree of weak C-D···O hydrogen bonding between the two crystals, which calls into question the role of these interactions in determining the conformation of the ethylene glycol molecule.

  16. 46 CFR 154.1725 - Ethylene oxide.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Ethylene oxide. 154.1725 Section 154.1725 Shipping COAST....1725 Ethylene oxide. (a) A vessel carrying ethylene oxide must: (1) Have cargo piping, vent piping, and... space of an ethylene oxide cargo tank for a period of 30 days under the condition of paragraph (e) of...

  17. Quantitative analysis of surface amine groups on plasma-polymerized ethylenediamine films using UV-visible spectroscopy compared to chemical derivatization with FT-IR spectroscopy, XPS and TOF-SIMS

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jinmo [Department of Physics, Brain Korea 21 Physics Research Division and Institute of Basic Science, Sungkyunkwan University (SKKU), Suwon 440-746 (Korea, Republic of); Division of Advanced Technology, Korea Research Institute of Standards and Science (KRISS), Daejeon 305-600 (Korea, Republic of); Jung, Donggeun [Department of Physics, Brain Korea 21 Physics Research Division and Institute of Basic Science, Sungkyunkwan University (SKKU), Suwon 440-746 (Korea, Republic of); Park, Yongsup [Division of Advanced Technology, Korea Research Institute of Standards and Science (KRISS), Daejeon 305-600 (Korea, Republic of); Kim, Yongki [Department of Physics, Brain Korea 21 Physics Research Division and Institute of Basic Science, Sungkyunkwan University (SKKU), Suwon 440-746 (Korea, Republic of); Division of Advanced Technology, Korea Research Institute of Standards and Science (KRISS), Daejeon 305-600 (Korea, Republic of); Moon, Dae Won [Division of Advanced Technology, Korea Research Institute of Standards and Science (KRISS), Daejeon 305-600 (Korea, Republic of); Lee, Tae Geol [Division of Advanced Technology, Korea Research Institute of Standards and Science (KRISS), Daejeon 305-600 (Korea, Republic of)]. E-mail: tglee@kriss.re.kr

    2007-02-28

    A quantitative analysis of the surface density of amine groups on a plasma-polymerized ethylenediamine thin film deposited on a platinum surface using inductively coupled plasma chemical vapor deposition method is described. UV-visible spectroscopy together with a chemical derivatization technique using Fourier transform infrared (FT-IR) spectroscopy was used to obtain the quantitative information. Chemical tags of pentafluorobenzaldehyde were hybridized with the surface amine groups and were easily detected due to the characteristic absorption bands of C-F stretching, aromatic ring and C=N stretching vibrations in the reflection-absorption FT-IR spectra. The surface amine density was reproducibly controlled as a function of deposition plasma power and quantified using UV-visible spectroscopy. A good linear correlation was observed between the FT-IR intensities of the characteristic absorption bands and the surface amine densities, suggesting the possibility of using this chemical derivatization technique to quantify the surface densities of specific functional groups on an organic surface. Chemical derivatization was also used with X-ray photoelectron spectroscopy on the same samples, and the results were compared with those obtained from FT-IR and time-of-flight secondary ion mass spectrometry. Although each analysis technique has different probing depths from the surface, the three different data sets obtained from the chemical tags correlated well with each other since each analysis technique measured the chemical tags on the sample surface.

  18. Chemical tagging with APOGEE: Discovery of a large population of N-rich stars in the inner Galaxy

    CERN Document Server

    Schiavon, Ricardo P; Carrera, Ricardo; Lucatello, Sara; Robin, A C; Ness, Melissa; Martell, Sarah L; Smith, Verne V; Hernandez, D A Garcia; Manchado, Arturo; Schoenrich, Ralph; Bastian, Nate; Chiappini, Cristina; Shetrone, Matthew; Mackereth, J Ted; Williams, Rob A; Meszaros, Szabolcs; Prieto, Carlos Allende; Anders, Friedrich; Bizyaev, Dmitry; Beers, Timothy C; Chojnowski, S Drew; Cunha, Katia; Epstein, Courtney; Frinchaboy, Peter M; Perez, Ana E Garcia; Hearty, Fred R; Holtzman, Jon A; Johnson, Jennifer A; Kinemuchi, Karen; Majewski, Steven R; Muna, Demitri; Nidever, David L; Nguyen, Duy Cuong; O'Connell, Robert W; Oravetz, Daniel; Pan, Kaike; Pinsonneault, Marc; Schneider, Donald P; Schultheis, Matthias; Simmons, Audrey; Skrutskie, Michael F; Sobeck, Jennifer; Wilson, John C; Zasowski, Gail

    2016-01-01

    Formation of globular clusters (GCs), the Galactic bulge, or galaxy bulges in general, are important unsolved problems in Galactic astronomy. Homogeneous infrared observations of large samples of stars belonging to GCs and the Galactic bulge field are one of the best ways to study these problems. We report the discovery by APOGEE of a population of field stars in the inner Galaxy with abundances of N, C, and Al that are typically found in GC stars. The newly discovered stars have high [N/Fe], which is correlated with [Al/Fe] and anti-correlated with [C/Fe]. They are homogeneously distributed across, and kinematically indistinguishable from, other field stars in the same volume. Their metallicity distribution is seemingly unimodal, peaking at [Fe/H]~-1, thus being in disagreement with that of the Galactic GC system. Our results can be understood in terms of different scenarios. N-rich stars could be former members of dissolved GCs, in which case the mass in destroyed GCs exceeds that of the surviving GC system...

  19. NafionTM膜表面改性用等离子体聚合方法提高膜的阳离子选择性%Surface Modification of Ion Exchange Membrane(NafionTM) The Enhancement of Cation Selectivity by Plasma Polymerization Process

    Institute of Scientific and Technical Information of China (English)

    曾蓉; 朱鹤孙; 庞志成; 弋峰

    2001-01-01

    An ultra-thin anionic exchange layer containing —NH2 and —CONH2 was deposited on the surface of NafionTM membrane. This layer was deposited from ethylene and ammonia using a glow-discharge plasma polymerization technique. The SEM, ATR(attenuated total reflection) spectra and XPS(X-ray photoelectron spectroscopy) showed that the resulted plasma polymers containing —NH2 and —CONH2 was about 0.5 μm thick. The proton perm-selectivity of plasma-modified NafionTM membrane was expressed by tCu, the transference number of the Cu2+ ion through the membrane which was determined by using NafionTM membrane as the separator in a typical two-compartment cell(0.25 mol/L CuCl2-0.5mol/L HCl|plasma-modified NafionTM membrane|1 mol/L HCl). Pretreatment of the NafionTM membrane by oxygen sputtering enhanced the adhesion of plasma polymer onto its surface. The plasma-treated membrane exhibited a high perm-selectivity and its resistance in 1 mol/L HCl was only a little bit higher than NafionTM membrane(<0.5 Ω*cm2).%采用辉光放电等离子体聚合方法, 以C2H4和NH3为单体, 在NafionTM膜表面沉积一层含氨基及酰氨基的类聚乙烯阴离子交换膜, 提高了NafionTM膜对阳离子的选择性, 同时不显著增加膜电阻. 由SEM确定该等离子体聚合膜厚约0.5 μm, 用红外光谱及X光电子能谱表征膜结构. 采用四电极法测量膜电阻, 膜对质子的选择性由Cu2+的迁移数tCu表征, 用二室隔膜装置(0.25 mol/L CuCl2-0.5 mol/L HCl|等离子体处理膜|1 mol/L HCl)测量tCu. O2等离子体预处理NafionTM膜有利于沉积膜在NafionTM膜上的沉积并与NafionTM膜紧密结合. 经改性后的NafionTM膜电阻值仍然很小, 在1 mol/L HCl溶液中电阻小于0.5 Ω*cm2.

  20. Inhibition of ethylene production by rhizobitoxine

    Energy Technology Data Exchange (ETDEWEB)

    Owens, L.D.; Lieberman, M.; Kunishi, A.

    1970-01-01

    Rhizobitoxine, an inhibitor of methionine biosynthesis in Salmonella typhimurium, inhibited ethylene production about 75% in light-grown sorghum seedlings and in senescent apple tissue. Ethylene production stimulated by indoleacetic acid and kinetin in sorghum was similarly inhibited. With both apple and sorghum, the inhibition could only be partially relieved by additions of methionine. A methionine analogue, ..cap alpha..-keto-..gamma..-methylthiobutyric acid, which has been suggested as an intermediate between methionine and ethylene, had no effect on the inhibition. Incorporation of /sup 14/C from added methionine-/sup 14/C into ethylene was curtailed by rhizobitoxine to about the same extent as was ethylene production. These results suggest that rhizobitoxine interferes with ethylene biosynthesis by blocking the conversion of methionine to ethylene and not indirectly by inhibiting the biosynthesis of methionine. Ethylene production by Penicillium digitatum, a fungus which produces ethylene via pathways not utilizing methionine as a precursor, was not affected by rhizobitoxine. 16 references, 2 figures, 4 tables.

  1. RESIDUAL RISK ASSESSMENT: ETHYLENE OXIDE ...

    Science.gov (United States)

    This document describes the residual risk assessment for the Ethylene Oxide Commercial Sterilization source category. For stationary sources, section 112 (f) of the Clean Air Act requires EPA to assess risks to human health and the environment following implementation of technology-based control standards. If these technology-based control standards do not provide an ample margin of safety, then EPA is required to promulgate addtional standards. This document describes the methodology and results of the residual risk assessment performed for the Ethylene Oxide Commercial Sterilization source category. The results of this analyiss will assist EPA in determining whether a residual risk rule for this source category is appropriate.

  2. Colorometric detection of ethylene glycol vapor

    Science.gov (United States)

    Helm, C.; Mosier, B.; Verostko, C. E.

    1970-01-01

    Very low concentrations of ethylene glycol in air or other gases are detected by passing a sample through a glass tube with three partitioned compartments containing reagents which successively convert the ethylene glycol vapor into a colored compound.

  3. 49 CFR 173.323 - Ethylene oxide.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Ethylene oxide. 173.323 Section 173.323... SHIPMENTS AND PACKAGINGS Gases; Preparation and Packaging § 173.323 Ethylene oxide. (a) For packaging ethylene oxide in non-bulk packagings, silver mercury or any of its alloys or copper may not be used in any...

  4. Liquid ethylene-propylene copolymers

    Science.gov (United States)

    Rhein, R. A.; Ingham, J. D.; Humphrey, M. F.

    1975-01-01

    Oligomers are prepared by heating solid ethylene-propylene rubber in container that retains solid and permits liquid product to flow out as it is formed. Molecular weight and viscosity of liquids can be predetermined by process temperature. Copolymers have low viscosity for given molecular weight.

  5. ETHYLENE OXIDE-ETHYLENE TEREPHTHALATE SEGMENTED COPOLYMER SOLID ELECTROLYTE

    Institute of Scientific and Technical Information of China (English)

    LUO Xiaolie; WANG Chuanqing; WANG Haiqian; HU Keliang; MA Dezhu

    1994-01-01

    A series of ethylene oxide-ethylene terephthalate segmented copolymers (EOET) were synthesized and complexed with LiClO4 to form some new polymer electrolytes. The EOET-LiClO4 electrolytes exhibit not only high ionic conductivity, but also good mechanical strength and toughness. The EOET 3400-25-LiClO4 complex possesses the highest conductivity (4. 65 ×10-5s·cm-1)at room temperature when the ratio [Li+]/[EO] equals 1/16.The structures of these electrolytes were examined with FTIR analysis, X-ray diffraction and DSC thermograms, and the results of high ionic conductivity of the segmented copolymers were discussed.

  6. Responsive Plasma Polymerized Ultrathin Nanocomposite Films

    Science.gov (United States)

    2012-01-01

    al. Soft Matter 2008;4:1796e8. [2] Schmidt S, Motschman H, Hellweg T, von Klitzing R. Polymer 2008;49:749e56. [3] Julthongpiput D, Lin Y-H, Teng J...et al. Nat Mater 2010;9:101e13. [7] Xu W, Yin X, He G, Zhao J, Wang H. Soft Matter 2012;8:3105e11. [8] Luzinov I, Minko S, Tsukruk VV. Prog Polym Sci...Films 2006;515:2618e24. [35] Yagüe JL, Gleason KK. Soft Matter 2012;8:2890e4. [36] Cheng X, Canavan HE, Stein MJ, Hull JR, Kweskin SJ, Wagner MS, et al

  7. Drying poly(ethylene glycol)

    OpenAIRE

    sprotocols

    2015-01-01

    Authors: Lucas Kinard, Kurtis Kasper & Antonios Mikos ### Abstract This protocol describes the drying of poly(ethylene glycol) (PEG) by a simple 6 step procedure. One can implement this protocol using common lab glass and lab equipment. Water is removed from PEG by azeotropic distillation in toluene. The two components are mixed and toluene and water are distilled off by heating the solution to 170°C. This procedure can be implemented in ~2 h. ### Introduction In many ...

  8. Ethylene Glycol Metabolism by Pseudomonas putida

    OpenAIRE

    Mückschel, Björn; Simon, Oliver; Klebensberger, Janosch; Graf, Nadja; Rosche, Bettina; Altenbuchner, Josef; Pfannstiel, Jens; Huber, Armin; Hauer, Bernhard

    2012-01-01

    In this study, we investigated the metabolism of ethylene glycol in the Pseudomonas putida strains KT2440 and JM37 by employing growth and bioconversion experiments, directed mutagenesis, and proteome analysis. We found that strain JM37 grew rapidly with ethylene glycol as a sole source of carbon and energy, while strain KT2440 did not grow within 2 days of incubation under the same conditions. However, bioconversion experiments revealed metabolism of ethylene glycol by both strains, with the...

  9. Biocatalytic conversion of ethylene to ethylene oxide using an engineered toluene monooxygenase

    Energy Technology Data Exchange (ETDEWEB)

    Carlin, DA; Bertolani, SJ; Siegel, JB

    2015-01-01

    Mutants of toluene o-xylene monooxygenase are demonstrated to oxidize ethylene to ethylene oxide in vivo at yields of >99%. The best mutant increases ethylene oxidation activity by >5500-fold relative to the native enzyme. This is the first report of a recombinant enzyme capable of carrying out this industrially significant chemical conversion.

  10. Biocatalytic conversion of ethylene to ethylene oxide using an engineered toluene monooxygenase.

    Science.gov (United States)

    Carlin, D A; Bertolani, S J; Siegel, J B

    2015-02-11

    Mutants of toluene o-xylene monooxygenase are demonstrated to oxidize ethylene to ethylene oxide in vivo at yields of >99%. The best mutant increases ethylene oxidation activity by >5500-fold relative to the native enzyme. This is the first report of a recombinant enzyme capable of carrying out this industrially significant chemical conversion.

  11. Poly(ethylene oxide) functionalization

    Energy Technology Data Exchange (ETDEWEB)

    Pratt, Russell Clayton

    2014-04-08

    A simple procedure is provided by which the hydroxyl termini of poly(ethylene oxide) can be appended with functional groups to a useful extent by reaction and precipitation. The polymer is dissolved in warmed toluene, treated with an excess of organic base and somewhat less of an excess of a reactive acylating reagent, reacted for several hours, then precipitated in isopropanol so that the product can be isolated as a solid, and salt byproducts are washed away. This procedure enables functionalization of the polymer while not requiring laborious purification steps such as solvent-solvent extraction or dialysis to remove undesirable side products.

  12. $\\gamma$ -spectroscopy of n-rich $^{95,96}$Rb nuclei by the incomplete fusion reaction of $^{94}$Kr on $^{7}$Li

    CERN Multimedia

    We propose an experiment with MINIBALL coupled to T-REX to investigate n-rich $^{95,96}$Rb nuclei by the incomplete fusion reaction of $^{94}$Kr on $^{7}$Li. The nuclei of interest will be populated by transfer of a triton into $^{94}$Kr, forming the excited $^{97}$Rb nucleus, followed by the emission of an alpha particle, which will be detected in the Si telescopes of T-REX. The $^{97}$Rb product will evaporate 1 or 2 (with the highest probability) neutrons leading to $^{96}$Rb or $^{95}$Rb, respectively. The aim of the experiment is twofold: \\\\ i) to perform a $\\gamma$- spectroscopy study of $^{95,96}$Rb nuclei with N=58,59, the structure of which is of particular interest in investigating the transition towards stable deformation at N=60, \\\\ ii) to acquire experience in using incomplete fusion reactions with the weakly bound $^{7}$Li target, in order to perform, at a later stage with HIE-ISOLDE, similar measurements induced by n-rich radioactive beams of Sn and Hg, for which at least 5 MeV/nucleon are need...

  13. 29 CFR 1926.1147 - Ethylene oxide.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 8 2010-07-01 2010-07-01 false Ethylene oxide. 1926.1147 Section 1926.1147 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR... Ethylene oxide. Note: The requirements applicable to construction work under this section are identical to...

  14. 29 CFR 1915.1047 - Ethylene oxide.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 7 2010-07-01 2010-07-01 false Ethylene oxide. 1915.1047 Section 1915.1047 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR... § 1915.1047 Ethylene oxide. Note: The requirements applicable to shipyard employment under this section...

  15. Ethylene: A tiny molecule with great potential

    NARCIS (Netherlands)

    Woltering, E.J.; Vrije, de T.

    1995-01-01

    Ethylene (C2H4) is a gaseous plant hormone produced by higher and lower (green) plants and, when grown on appropriate substrates, also by fungi, yeasts and bacteria. Ethylene is involved in many developmental processes in plants and is biologically active in trace amounts (10-100 nl/l of air) that m

  16. Serum Calcium Concentration in Ethylene Glycol Poisoning.

    Science.gov (United States)

    Hodgman, Michael; Marraffa, Jeanna M; Wojcik, Susan; Grant, William

    2017-06-01

    The diagnosis of ethylene glycol intoxication can be challenging. Definitive testing for ethylene glycol is not readily available and clinical decisions are often based on clinical suspicion and the results of more readily available tests. One of these findings is hypocalcemia, presumable through complexation with the ethylene glycol metabolite oxalate. We performed a retrospective review of all patients admitted to a tertiary care hospital between 2005 and 2013 with laboratory confirmed ethylene glycol intoxication. Serum calcium on presentation was compared to blood gas pH on presentation as well as presentation serum bicarbonate. We did not find any relationship between calcium and serum pH either by linear regression or when dichotomized by pH ≥ or ethylene glycol poisoning, even in acidotic patients.

  17. Ethylene-dependent/ethylene-independent ABA regulation of tomato plants colonized by arbuscular mycorrhiza fungi.

    Science.gov (United States)

    Martín-Rodríguez, José Ángel; León-Morcillo, Rafael; Vierheilig, Horst; Ocampo, Juan Antonio; Ludwig-Müller, Jutta; García-Garrido, José Manuel

    2011-04-01

    We investigated the relationship between ABA and ethylene regulating the formation of the arbuscular mycorrhiza (AM) symbiosis in tomato (Solanum lycopersicum) plants and tried to define the specific roles played by each of these phytohormones in the mycorrhization process. We analysed the impact of ABA biosynthesis inhibition on mycorrhization by Glomus intraradices in transgenic tomato plants with an altered ethylene pathway. We also studied the effects on mycorrhization in sitiens plants treated with the aminoethoxyvinyl glycine hydrochloride (AVG) ethylene biosynthesis inhibitor and supplemented with ABA. In addition, the expression of plant and fungal genes involved in the mycorrhization process was studied. ABA biosynthesis inhibition qualitatively altered the parameters of mycorrhization in accordance with the plant's ethylene perception and ethylene biosynthesis abilities. Inhibition of ABA biosynthesis in wild-type plants negatively affected all the mycorrhization parameters studied, while tomato mutants impaired in ethylene synthesis only showed a reduced arbuscular abundance in mycorrhizal roots. Inhibition of ethylene synthesis in ABA-deficient sitiens plants increased the intensity of mycorrhiza development, while ABA application rescued arbuscule abundance in the root's mycorrhizal zones. The results of our study show an antagonistic interaction between ABA and ethylene, and different roles of each of the two hormones during AM formation. This suggests that a dual ethylene-dependent/ethylene-independent mechanism is involved in ABA regulation of AM formation. © 2011 The Authors. New Phytologist © 2011 New Phytologist Trust.

  18. Ethylene and flower longevity in Alstroemeria: relationship between tepal senescence, abscission and ethylene biosynthesis.

    Science.gov (United States)

    Wagstaff, Carol; Chanasut, Usawadee; Harren, Frans J M; Laarhoven, Luc-Jan; Thomas, Brian; Rogers, Hilary J; Stead, Anthony D

    2005-03-01

    Senescence of floral organs is broadly divided into two groups: those that exhibit sensitivity to exogenous ethylene and those that do not. Endogenous ethylene production from the former group is via a well-characterized biochemical pathway and is either due to developmental or pollination-induced senescence. Many flowers from the order Liliales are characterized as ethylene-insensitive since they do not appear to produce endogenous ethylene, or respond to exogenous ethylene treatments, however, the majority of cases studied are wilting flowers, rather than those where life is terminated by perianth abscission. The role of ethylene in the senescence and abscission of Alstroemeria peruviana cv. Rebecca and cv. Samora tepals was previously unclear, with silver treatments recommended for delaying leaf rather than flower senescence. In the present paper the effects of exogenous ethylene, 2-chloroethylphosphonic acid (CEPA) and silver thiosulphate (STS) treatments on tepal senescence and abscission have been investigated. Results indicate that sensitivity to ethylene develops several days after flower opening such that STS only has a limited ability to delay tepal abscission. Detachment force measurements indicate that cell separation events are initiated after anthesis. Endogenous ethylene production was measured using laser photoacoustics and showed that Alstroemeria senesce independently of ethylene production, but that an extremely small amount of ethylene (0.15 nl flower(-1) h(-1)) is produced immediately prior to abscission. Investigation of the expression of genes involved in ethylene biosysnthesis by semi-quantitative RT-PCR indicated that transcriptional regulation is likely to be at the level of ACC oxidase, and that the timing of ACC oxidase gene expression is coincident with development of sensitivity to exogenous ethylene.

  19. Excitonic localization in AlN-rich AlxGa1−xN/AlyGa1−yN multi-quantum-well grain boundaries

    KAUST Repository

    Ajia, Idris A.

    2014-09-22

    AlGaN/AlGaN multi-quantum-wells (MQW) with AlN-rich grains have been grown by metal organic chemical vapor deposition. The grains are observed to have strong excitonic localization characteristics that are affected by their sizes. The tendency to confine excitons progressively intensifies with increasing grain boundary area. Photoluminescence results indicate that the MQW have a dominant effect on the peak energy of the near-bandedge emission at temperatures below 150 K, with the localization properties of the grains becoming evident beyond 150 K. Cathodoluminescence maps reveal that the grain boundary has no effect on the peak intensities of the AlGaN/AlGaN samples.

  20. Ethylene glycol metabolism by Pseudomonas putida.

    Science.gov (United States)

    Mückschel, Björn; Simon, Oliver; Klebensberger, Janosch; Graf, Nadja; Rosche, Bettina; Altenbuchner, Josef; Pfannstiel, Jens; Huber, Armin; Hauer, Bernhard

    2012-12-01

    In this study, we investigated the metabolism of ethylene glycol in the Pseudomonas putida strains KT2440 and JM37 by employing growth and bioconversion experiments, directed mutagenesis, and proteome analysis. We found that strain JM37 grew rapidly with ethylene glycol as a sole source of carbon and energy, while strain KT2440 did not grow within 2 days of incubation under the same conditions. However, bioconversion experiments revealed metabolism of ethylene glycol by both strains, with the temporal accumulation of glycolic acid and glyoxylic acid for strain KT2440. This accumulation was further increased by targeted mutagenesis. The key enzymes and specific differences between the two strains were identified by comparative proteomics. In P. putida JM37, tartronate semialdehyde synthase (Gcl), malate synthase (GlcB), and isocitrate lyase (AceA) were found to be induced in the presence of ethylene glycol or glyoxylic acid. Under the same conditions, strain KT2440 showed induction of AceA only. Despite this difference, the two strains were found to use similar periplasmic dehydrogenases for the initial oxidation step of ethylene glycol, namely, the two redundant pyrroloquinoline quinone (PQQ)-dependent enzymes PedE and PedH. From these results we constructed a new pathway for the metabolism of ethylene glycol in P. putida. Furthermore, we conclude that Pseudomonas putida might serve as a useful platform from which to establish a whole-cell biocatalyst for the production of glyoxylic acid from ethylene glycol.

  1. Root formation in ethylene-insensitive plants.

    Science.gov (United States)

    Clark, D G; Gubrium, E K; Barrett, J E; Nell, T A; Klee, H J

    1999-09-01

    Experiments with ethylene-insensitive tomato (Lycopersicon esculentum) and petunia (Petunia x hybrida) plants were conducted to determine if normal or adventitious root formation is affected by ethylene insensitivity. Ethylene-insensitive Never ripe (NR) tomato plants produced more below-ground root mass but fewer above-ground adventitious roots than wild-type Pearson plants. Applied auxin (indole-3-butyric acid) increased adventitious root formation on vegetative stem cuttings of wild-type plants but had little or no effect on rooting of NR plants. Reduced adventitious root formation was also observed in ethylene-insensitive transgenic petunia plants. Applied 1-aminocyclopropane-1-carboxylic acid increased adventitious root formation on vegetative stem cuttings from NR and wild-type plants, but NR cuttings produced fewer adventitious roots than wild-type cuttings. These data suggest that the promotive effect of auxin on adventitious rooting is influenced by ethylene responsiveness. Seedling root growth of tomato in response to mechanical impedance was also influenced by ethylene sensitivity. Ninety-six percent of wild-type seedlings germinated and grown on sand for 7 d grew normal roots into the medium, whereas 47% of NR seedlings displayed elongated tap-roots, shortened hypocotyls, and did not penetrate the medium. These data indicate that ethylene has a critical role in various responses of roots to environmental stimuli.

  2. Synthesis, thermogravimetric study and crystal structure of an N-rich copper(II) compound with tren ligands and nitrate counter-anions

    Energy Technology Data Exchange (ETDEWEB)

    Pérez-Toro, Inmaculada; Domínguez-Martín, Alicia [Department of Inorganic Chemistry, Faculty of Pharmacy, University of Granada, 18071 Granada (Spain); Choquesillo-Lazarte, Duane [Laboratorio de Estudios Cristalográficos, IACT, CSIC-Universidad de Granada, Av. de las Palmeras 4, E-18100 Armilla, Granada (Spain); Vílchez-Rodríguez, Esther [Department of Inorganic Chemistry, Faculty of Pharmacy, University of Granada, 18071 Granada (Spain); Department of Inorganic Chemistry, Faculty of Pharmacy, University of Santiago de Compostela, 15782 Santiago de Compostela (Spain); Castiñeiras, Alfonso [Department of Inorganic Chemistry, Faculty of Pharmacy, University of Santiago de Compostela, 15782 Santiago de Compostela (Spain); Niclós-Gutiérrez, Juan, E-mail: jniclos@ugr.es [Department of Inorganic Chemistry, Faculty of Pharmacy, University of Granada, 18071 Granada (Spain)

    2014-10-10

    The N-rich salt [{Cu(tren)}{sub 3}(μ{sub 3}-tren)]{sub 2}(NO{sub 3}){sub 12}·3H{sub 2}O has been studied by XRD and by coupled TG and FT-IR spectroscopy of the evolved gases. After water loss, thermal decomposition of the nitrate ions and some tren ligands in the salt are overlapped. - Highlights: • A novel N-rich copper(II)-tren complex has been crystallized as a 3-hydrated nitrate salt. • Tren acts both as tripodal tetradentate and as μ{sub 3}-tren bridging ligand. • Copper(II) centers exhibit distorted trigonal bipyramidal coordination. • Coupled thermogravimetry and FT-IR spectra of evolved gases have been used. • Decomposition of nitrate anions and tren ligands occurs in an overlapped step. - Abstract: The compound [{Cu(tren)}{sub 3}(μ3-tren)]{sub 2}(NO{sub 3}){sub 12}·3H{sub 2}O has been synthesized, crystallized and characterized by single crystal X-ray diffraction, thermogravimetry (TG) coupled to FT-IR spectroscopy of the evolved gases, TG–differential scanning calorimetry (DSC) and electronic (diffuse reflectance) and FT-IR spectroscopies. The sample loses the crystallization water between room temperature and 200 °C. The decomposition of the salt begins with an overlapped decomposition of nitrate anions and some tren ligands where CO{sub 2}, H{sub 2}O, CO, NH{sub 3}, N{sub 2}O, NO and NO{sub 2} are evolved (205–235 °C). Then decomposition of additional tren ligands takes place (235–725 °C). Finally a non-pure CuO residue is obtained at 725 °C.

  3. 46 CFR 151.50-12 - Ethylene oxide.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Ethylene oxide. 151.50-12 Section 151.50-12 Shipping... BULK LIQUID HAZARDOUS MATERIAL CARGOES Special Requirements § 151.50-12 Ethylene oxide. (a)(1) Ethylene... otherwise provided for in paragraph (a)(3) of this section. (2) Ethylene oxide shall be loaded at a...

  4. 21 CFR 880.6860 - Ethylene oxide gas sterilizer.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Ethylene oxide gas sterilizer. 880.6860 Section... Miscellaneous Devices § 880.6860 Ethylene oxide gas sterilizer. (a) Identification. An ethylene gas sterilizer is a nonportable device intended for use by a health care provider that uses ethylene oxide (ETO) to...

  5. 21 CFR 172.770 - Ethylene oxide polymer.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ethylene oxide polymer. 172.770 Section 172.770... CONSUMPTION Other Specific Usage Additives § 172.770 Ethylene oxide polymer. The polymer of ethylene oxide may... conditions. (a) It is the polymer of ethylene oxide having a minimum viscosity of 1,500 centipoises in a 1...

  6. The role of ethylene perception in plant disease resistance

    NARCIS (Netherlands)

    Geraats, Bart Peter Johan

    2003-01-01

    Ethylene is a plant hormone that is involved in responses of the plant to various stress situations, such as pathogen attack. The role of ethylene in plant-pathogen interactions seems to be diverse. Exposure of plants to ethylene can induce disease resistance, but treatment with ethylene during

  7. Ethylene Glycol and Metabolite Concentrations in Fatal Ethylene Glycol Poisonings.

    Science.gov (United States)

    Viinamäki, Jenni; Sajantila, Antti; Ojanperä, Ilkka

    2015-01-01

    Ethylene glycol (EG) is used in antifreeze and other industrial products. It metabolizes to glycolic acid (GA) and oxalic acid (OX) that cause metabolic acidosis and are mainly responsible for the toxicity of EG. During 2010-2014, EG or GA was found in 25 postmortem cases in Finland. Of these cases, 21 were classified as fatal EG poisonings and 3 were classified as methanol (MeOH) poisonings. In this study, we report the concentrations of EG and GA in postmortem blood and urine samples of fatal EG or mixed MeOH/EG poisonings. In the fatal EG poisonings, the median EG and GA concentrations were 0.87 and 1.6 g/L in blood and 4.3 and 5.3 g/L in urine. The median urine-blood ratios were 3.8 and 3.1 for EG and GA. These results warrant the use of urine as a primary matrix for screening. In EG positive cases, the quantification of both EG and GA in blood is crucial as GA concentration appears to best indicate a fatal poisoning with an approximate threshold of 1.5 g/L. The measurement of urinary OX does not offer much additional value to toxic alcohol screening as it may originate from varying dietary conditions. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  8. Contamination control by use of ethylene oxide

    Science.gov (United States)

    Stroud, R. H.; Lyle, R. G.

    1972-01-01

    The uses of ethylene oxide as a decontaminating agent for planetary quarantine related applications are reported. Aspects discussed include: applications and limitations, chemical and physical properties, germicidal activity, methods of applications, and effects on personnel.

  9. Nitrous Oxide Ethane Ethylene Engine Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The Nitrous Oxide Ethane-Ethylene (NEE) engine is a proposed technology designed to provide spacecraft with non-toxic non-cryogenic high-performance propulsion. With...

  10. Inert Reassessment Document for Ethylene Glycol

    Science.gov (United States)

    Ethylene Glycol has many uses and are also used as antifreeze and deicers, as solvents, humectants, as chemical intermediates in the synthesis of other chemicals, and as components of many products such as brake fluids, lubricants, inks,and lacquers.

  11. Polymer coatings on plane and spherical surfaces obtained by plasma polymerization from trans-2-butene and hydrogen mixture; Depots de polymere sur surfaces planes et spheriques obtenus par polymerisation plasma a partir d`un melange de trans-2-butene et d`hydrogene

    Energy Technology Data Exchange (ETDEWEB)

    Benardais, A

    1997-10-21

    This study of a low frequency plasma polymerization process was undertaken to be used in manufacturing of targets used in laser-matter interaction experiments. In this system, whether the sample is placed in the discharge or outside of the discharge, hydrocarbon coatings from a gaseous mixture of hydrogen and trans-2-butene are obtain. This study consists of two parts. We first dealt with the understanding of plasma polymerization mechanisms in the reactor which resulted in a better process optimization. The study of gas flow in the reactor allowed us to determine the species repartition in the vessel. With experiments performed on the electrical behavior in the reactor we were able to define the discharge type. Then, species present in the plasma were analysed by emission spectroscopy and mass spectrometry and then reaction mechanisms were proposed. Attention was paid to the role of hydrogen which in fact acted as a reagent like trans-2-butene. We also worked on the process optimization in order to obtain a good working point which produces coatings which are as transparent as possible, contain only carbon and hydrogen (and the least amount of oxygen), have a smooth surface finish (mean square root of roughness < 50 nm) and retain their qualities overtime. After the reactor characterization, the study of the effects of different parameters (inner or post-discharge coatings, pressure, total gas flow, composition of the mixture of trans-2-butene and hydrogen, power, frequency, interelectrode distance) on deposition rate, roughness and chemical composition of coatings led to the finding of optimal deposition conditions. (author) 103 refs.

  12. Ethylene oxide and Acetaldehyde in hot cores

    CERN Document Server

    Occhiogrosso, A; Herbst, E; Viti, S; Ward, M D; Price, S D; Brown, W A

    2014-01-01

    [Abridged] Ethylene oxide and its isomer acetaldehyde are important complex organic molecules because of their potential role in the formation of amino acids. Despite the fact that acetaldehyde is ubiquitous in the interstellar medium, ethylene oxide has not yet been detected in cold sources. We aim to understand the chemistry of the formation and loss of ethylene oxide in hot and cold interstellar objects (i) by including in a revised gas-grain network some recent experimental results on grain surfaces and (ii) by comparison with the chemical behaviour of its isomer, acetaldehyde. We test the code for the case of a hot core. The model allows us to predict the gaseous and solid ethylene oxide abundances during a cooling-down phase prior to star formation and during the subsequent warm-up phase. We can therefore predict at what temperatures ethylene oxide forms on grain surfaces and at what temperature it starts to desorb into the gas phase. The model reproduces the observed gaseous abundances of ethylene oxid...

  13. Temperature Distribution in Ethylene Pyrolyzer

    Institute of Scientific and Technical Information of China (English)

    蓝兴英; 高金森; 徐春明

    2003-01-01

    Abstract A good understanding of the detailed temperature distribution in the furnace plays an important role in the implementation of operation optimization and design improvement of ethylene pyrolyzer. Numerical simulation of the turbulent flow, combustion and heat transfer was carried out to investigate the temperature distribution in industrial furnace. Inhomogeneities of the flue-gas temperature distribution were observed in X, Y, and Z direction of the furnace from the simulated results. Along the height of the furnace, the average flue-gas temperature increased initially and decreased afterward, and reached its peak at the height of 5m. The reactor tube skin temperature varied not only along the height of the furnace, but also around the circumference of the tube. The heat flux profiles from the furnace towards the reactor tubes followed the shape of the average flue-gas temperature profile. The heat flux of the inlet tubes was constantly higher than that of the outlet tubes at the same height in the furnace.

  14. Ethylene Controls Autophosphorylation of the Histidine Kinase Domain in Ethylene Receptor ETR1

    Institute of Scientific and Technical Information of China (English)

    Jan Voet-van-Vormizeele; Georg Groth

    2008-01-01

    Perception of the phytohormone ethylene is accomplished by a small family of integral membrane receptors.In Arabidopsis,five ethylene receptor proteins are known,including ethylene resistant 1 (ETR1).The hydrophobic aminoterminal domain of these receptors contains the ethylene-binding site while the carboxyl-terminal part consists of a histidine kinase domain and a response regulator domain,which are well known elements found in bacterial two-component signaling.The soluble membrane-extrinsic carboxyl-terminal part of the receptor,which is likely to play an important role in signal transduction,showed intrinsic kinase activity when expressed and purified on its own.However,a correlation between signal input and autokinase activity was not established in these studies,as receptors were missing the transmembrane amino-terminal sensor domain.Thus,it is still unclear whether autophosphorylation occurs in response to perception of the ethylene signal.Here,we report on autophosphorylation studies of purified full-length ETR1.Autokinase activity of the purified receptor is controlled by ethylene or by ethylene agonists like the π-acceptor compound cyanide.In fact,both signal molecules were able to completely turn off the intrinsic kinase activity.Furthermore,the observed inhibition of autophosphorylation in ETR1 by both molecules could be prevented when the ethylene antagonist 1-methyl-cyclopropene (MCP) was applied.

  15. Synthesis of N-rich microporous carbon materials from chitosan by alkali activation using Na{sub 2}CO{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Ilnicka, Anna; Lukaszewicz, Jerzy P., E-mail: jerzy_lukaszewicz@o2.pl

    2015-11-15

    Highlights: • The novel manufacturing procedure of nitrogen-rich carbon materials. • The biopolymer chitosan can be activated by sodium carbonate. • The effect of the addition of activator and the temperature of carbonization was investigated. • The N-rich carbon materials exhibit high specific surface area and microporous structure. - Abstract: The paper presents the first systematic study on the synthesis of nitrogen-rich nanoporous activated carbons by chitosan carbonization in the presence of a hard template (activator), i.e. Na{sub 2}CO{sub 3}. Carbonization process was carried out in the range of 600–900 °C under a flow of nitrogen. The effect of the addition of different volumes of activator and the temperature of carbonization on the development of specific surface area and pore structure (pore volume and median pore diameter) of the activated carbons was investigated. Additionally, the nitrogen content and nitrogen-containing surface species were determined by means of XPS and combustion elemental analysis. The nitrogen content was placed in the range of 2.4–13.1 wt.%. On the grounds of the low-temperature adsorption of nitrogen, it was found that obtained adsorption isotherms were of type-I, based on the IUPAC classification, which is typical for microporous materials.

  16. Compositional, structural and morphological modifications of N-rich Cu{sub 3}N films induced by irradiation with Cu ions at 42 MeV

    Energy Technology Data Exchange (ETDEWEB)

    Gordillo, N [Fundacion Parque CientIfico de Madrid, E-28049, Madrid (Spain); Rivera, A; Gonzalez-Arrabal, R [Instituto de Microelectronica de Madrid C/ Isaac Newton, 8. Tres Cantos, Madrid. E-28760 (Spain); Groetzschel, R; Munnik, F; Guettler, D [Forschungszentrum Dresden-Rossendorf, PO Box 10119, D-01314 Dresden (Germany); Crespillo, M L; Agullo-Lopez, F, E-mail: nuria.gordillo@uam.e [Centro de Microanalisis de Materiales, Universidad Autonoma de Madrid, E-28049, Madrid (Spain)

    2010-09-01

    N-rich Cu{sub 3}N films were irradiated with Cu at 42 MeV in the fluences range from 4 x 10{sup 11} to 1 x 10{sup 14} cm{sup -2}. The radiation-induced changes in the chemical composition, structural phases, surface morphology and optical properties have been characterized as a function of ion fluence, substrate temperature and angle of incidence of the incoming ion by means of ion-beam analysis (IBA), x-ray diffraction, atomic force microscopy, profilometry and Fourier transform infrared spectroscopy techniques. IBA methods reveal a very efficient sputtering of N whose yield (5 x 10{sup 3} atom/ion) is almost independent of substrate temperature (RT-300 {sup 0}C) but slightly depends on the incidence angle of the incoming ion. The Cu content remains essentially constant within the investigated fluence range. All data suggest an electronic mechanism to be responsible for the N depletion. The release of nitrogen and the formation of Cu{sub 2}O and metallic Cu are discussed on the basis of existing models.

  17. N-rich protein (NRP)-mediated cell death signaling: a new branch of the ER stress response with implications for plant biotechnology.

    Science.gov (United States)

    Reis, Pedro A B; Fontes, Elizabeth P B

    2012-06-01

    Upon disruption of ER homeostasis, plant cells activate at least two branches of the unfolded protein response (UPR) through IRE1-like and ATAF6-like transducers, resulting in the upregulation of ER-resident molecular chaperones and the activation of the ER-associated degradation protein system. Here, we discuss a new ER stress response pathway in plants that is associated with an osmotic stress response in transducing a cell death signal. Both ER and osmotic stress induce the expression of the novel transcription factor GmERD15, which binds and activates N-rich protein (NRP) promoters to induce NRP expression and cause the upregulation of GmNAC6, an effector of the cell death response. In contrast to this activation mechanism, the ER-resident molecular chaperone binding protein (BiP) attenuates the propagation of the cell death signal by modulating the expression and activity of components of the ER and osmotic stress-induced NRP-mediated cell death signaling. This interaction attenuates dehydration-induced cell death and promotes a better adaptation of BiP-overexpressing transgenic lines to drought.

  18. J-type Carbon Stars: A Dominant Source of 14N-rich Presolar SiC Grains of Type AB

    Science.gov (United States)

    Liu, Nan; Stephan, Thomas; Boehnke, Patrick; Nittler, Larry R.; O'D. Alexander, Conel M.; Wang, Jianhua; Davis, Andrew M.; Trappitsch, Reto; Pellin, Michael J.

    2017-07-01

    We report Mo isotopic data of 27 new presolar SiC grains, including 12 14N-rich AB (14N/15N > 440, AB2) and 15 mainstream (MS) grains, and their correlated Sr and Ba isotope ratios when available. Direct comparison of the data for the MS grains, which came from low-mass asymptotic giant branch (AGB) stars with large s-process isotope enhancements, with the AB2 grain data demonstrates that AB2 grains show near-solar isotopic compositions and lack s-process enhancements. The near-normal Sr, Mo, and Ba isotopic compositions of AB2 grains clearly exclude born-again AGB stars, where the intermediate neutron-capture process (i-process) takes place, as their stellar source. On the other hand, low-mass CO novae and early R- and J-type carbon stars show 13C and 14N excesses but no s-process enhancements and are thus potential stellar sources of AB2 grains. Because both early R-type carbon stars and CO novae are rare objects, the abundant J-type carbon stars (10%-15% of all carbon stars) are thus likely to be a dominant source of AB2 grains.

  19. Postharvest response of oranges of ethylene

    Energy Technology Data Exchange (ETDEWEB)

    Aharoni, Y.; Lattar, F.S.; Monselise, S.P.

    1969-01-01

    Since the effect of ethylene on the respiration rate of young unripe oranges has not yet been described, experiments were carried out to study the respiratory response of such fruits to ethylene. Oranges (Citrus sinensis (L.) Osbeck) of the Washington navel, Shamouti and Valencia varieties, growing on a sandy loam near Rehovot, Israel, were picked in June, July, September, December and January. Immediately after picking, they were weighed, placed in glass jars, and stored at 20/sup 0/. Each experiment comprised 12 jars, 4 for each variety. A constant stream (200 ml/min) of air containing 20 ppm of ethylene was run through the jars. The respiration rate was measured by the amount of CO/sub 2/ evolved by the fruits, and based on a fresh weight unit. The results show that in all 3 varieties, ethylene caused an immediate rise in respiration rate, at all stages of development tested, regardless of whether it was applied from the beginning of the test or after a certain period of storage in air. The pattern of response to ethylene of young unripe oranges (picked in June, July, and September) was therefore similar to that of ripe ones (picked in December and January).

  20. Catalytic dehydration of ethanol to ethylene

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Ying; Jin, Zhaosheng; Shen, Wei [SINOPEC Shanghai Research Institute of Petrochemical Technology, Shanghai (China)

    2011-07-01

    The different routes of ethylene production were briefly introduced and the advantage of ethanol to ethylene (ETE) route was explained. Followed by that, the upgraded catalyst applied in this route developed by SINOPEC Shanghai Research Institute of Petrochemical Technology (SRIPT) was introduced together with the development of the ethanol to ethylene process. The core technologies involved in this process development were discussed, such as isothermal fixed-bed reactor, water scrubber and alkaline wash column, two columns of low-temperature separation as well as process heat integration. Furthermore, the performance of one of ethanol industrial plants licensed by SRIPT was reviewed. It is as follows, conversion of ethanol reaches 99% while selectivity of ethylene is over 96% at the reaction temperature of 350{approx}450 C, the liquid hourly space velocity (LHSV)of 0.5{approx}1.0 h{sup -1} and atmosphere pressure. Meanwhile, the catalyst shows its life time of one year. This route is considered not only as an economical and practical process but also as an environmentfriendly path to ethylene production. (orig.)

  1. THE EFFECT OF ETHYLENE IN MAINTAINING QUALITY OF TOMATO SLICES

    Directory of Open Access Journals (Sweden)

    Darwin H. Pangaribuan

    2009-06-01

    Full Text Available Processes such as slicing tomato fruits disrupt the plant tissue so the products become more perishable compared with the intact fruit. Ethylene production is stimulated during the slicing of fresh cut tomato slices. Experiments were conducted to investigate if ethylene absorbent and exogenous ethylene influences the quality of tomato slices cv. ‘Revolution’ during storage at 5C. In the experiment of ethylene absorbent, experiment was laid out in a completely randomised design. The treatments were plus 10 g and minus ethylene absorbent (KMnO4; Purafil; 5C for 12 d. In the experiment of ethylene concentrations, experiment was laid out in a completely randomised design. The treatments were exogenous ethylene concentrations of 0 (control, 0.1, 1 or 10 L L–1 respectively (5C for 6 h. In both experiments, the treatments were replicated 5 fold. Results showed that ethylene absorbent resulted in reduced ethylene accumulation, and CO2 accumulation in enclosed containers, and firmer slices. Ethylene applied 2 days after slicing stimulated the rate of ethylene production, CO2 production, and produced softer slices during storage. Changes in soluble solids concentration and titratable acidity development were independent of ethylene effects. These experiments showed that ethylene produced by slicing or introduced exogenously had an undesirable effect of accelerating softening of tomato slices.

  2. APC implementation in Chandra Asri - ethylene plant

    Science.gov (United States)

    Sidiq, Mochamad; Mustofa, Ali

    2017-05-01

    Nowadays, the modern process plants are continuously improved for maximizing production, Optimization of the energy and raw material and reducing the risk. Due to many disturbances appearance between the process units, hence, the failure of one unit might have a bad effect on the overall productivity. Ethylene Plant have significant opportunities for using Advanced Process Control (APC) technologies to improve operation stability, push closer to quality or equipment limit, and improve the capability of process units to handle disturbances. APC implementation had considered a best answer for solving multivariable control problem. PT. Chandra Asri Petrochemical, Tbk (CAP) operates a large naphtha cracker complex at Cilegon, Indonesia. To optimize the plant operation and to enhance the benefit, Chandra Asri has been decided to implement Advance Process Control (APC) for ethylene plant. The APC implementation technology scopes at CAP are as follows: 1. Hot Section : Furnaces, Quench Tower 2. Cold Section : Demethanizer, Deethanizer, Acetylene Converter, Ethylene Fractionator, Depropanizer, Propylene Fractionator, Debutanizer

  3. The proton dynamics of ethylene glycol

    CERN Document Server

    Novikov, A G; Sobolev, O V

    2002-01-01

    The results of inelastic neutron scattering experiments on ethylene glycol at T=300 K, T=348 K and T=393 K by using the 'direct-geometry' double time-of-flight neutron-scattering spectrometer DIN-2PI (Frank Laboratory of Neutron Physics, JINR, Dubna) are presented. The quasi-elastic and inelastic components of the neutron scattering have been considered. The diffusion characteristics and generalized frequency distributions for protons of ethylene glycol molecules were obtained from the neutron-scattering spectra. (orig.)

  4. Sinopec Group: Expanding Its Ethylene Business

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    @@ Since its establishment in 1998, Sinopec Group, China's largest integrated energy chemical enterprise, has been sticking to the principle of'developing the petrochemical industry and building core businesses' and actively promoted the development of its ethylene business under the favorable conditions of opportunities and industrial status. In particular in recent years, the group helped China to be the second largest ethylene producing country in the world by the way of importing-learning and absorbing-integrating and innovation through giving more attention to technology innovation, developing its comprehensive advantages, promoting integration between refining and chemical processes.

  5. THE EFFECT OF ETHYLENE IN MAINTAINING QUALITY OF TOMATO SLICES

    OpenAIRE

    Darwin H. Pangaribuan1)

    2009-01-01

    Processes such as slicing tomato fruits disrupt the plant tissue so the products become more perishable compared with the intact fruit. Ethylene production is stimulated during the slicing of fresh cut tomato slices. Experiments were conducted to investigate if ethylene absorbent and exogenous ethylene influences the quality of tomato slices cv. ‘Revolution’ during storage at 5C. In the experiment of ethylene absorbent, experiment was laid out in a completely randomised design. The treat...

  6. Involvement of wound and climacteric ethylene in ripening avocado discs.

    Science.gov (United States)

    Starrett, D A; Laties, G G

    1991-10-01

    Avocado (Persea americana Mill. cv Hass) discs (3 mm thick) ripened in approximately 72 hours when maintained in a flow of moist air and resembled ripe fruit in texture and taste. Ethylene evolution by discs of early and midseason fruit was characterized by two distinct components, viz. wound ethylene, peaking at approximately 18 hours, and climacteric ethylene, rising to a peak at approximately 72 hours. A commensurate respiratory stimulation accompanied each ethylene peak. Aminoethoxyvinyl glycine (AVG) given consecutively, at once and at 24 hours following disc preparation, prevented wound and climacteric respiration peaks, virtually all ethylene production, and ripening. When AVG was administered for the first 24 hours only, respiratory stimulation and softening (ripening) were retarded by at least a day. When AVG was added solely after the first 24 hours, ripening proceeded as in untreated discs, although climacteric ethylene and respiration were diminished. Propylene given together with AVG led to ripening under all circumstances. 2,5-Norbornadiene given continuously stimulated wound ethylene production, and it inhibited climacteric ethylene evolution, the augmentation of ethylene-forming enzyme activity normally associated with climacteric ethylene, and ripening. 2,5-Norbornadiene given at 24 hours fully inhibited ripening. When intact fruit were pulsed with ethylene for 24 hours before discs were prepared therefrom, the respiration rate, ethylene-forming enzyme activity buildup, and rate of ethylene production were all subsequently enhanced. The evidence suggests that ethylene is involved in all phases of disc ripening. In this view, wound ethylene in discs accelerates events that normally take place over an extended period throughout the lag phase in intact fruit, and climacteric ethylene serves the same ripening function in discs and intact fruit alike.

  7. 40 CFR 180.151 - Ethylene oxide; tolerances for residues.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Ethylene oxide; tolerances for... § 180.151 Ethylene oxide; tolerances for residues. (a) General. (1) Tolerances are established for residues of the antimicrobial agent and insecticide ethylene oxide, when used as a postharvest fumigant in...

  8. 21 CFR 880.6100 - Ethylene oxide gas aerator cabinet.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Ethylene oxide gas aerator cabinet. 880.6100... Miscellaneous Devices § 880.6100 Ethylene oxide gas aerator cabinet. (a) Identification. An ethyene oxide gas... required to remove residual ethylene oxide (ETO) from wrapped medical devices that have undergone ETO...

  9. Growth Control by Ethylene: Adjusting Phenotypes to the Environment

    NARCIS (Netherlands)

    Pierik, R.; Sasidharan, R.; Voesenek, L.A.C.J.

    2007-01-01

    Plants phenotypically adjust to environmental challenges, and the gaseous plant hormone ethylene modulates many of these growth adjustments. Ethylene can be involved in environmentally induced growth inhibition as well as growth stimulation. Still, ethylene has long been considered a growth inhibito

  10. 21 CFR 177.1350 - Ethylene-vinyl acetate copolymers.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ethylene-vinyl acetate copolymers. 177.1350 Section... Basic Components of Single and Repeated Use Food Contact Surfaces § 177.1350 Ethylene-vinyl acetate copolymers. Ethylene-vinyl acetate copolymers may be safely used as articles or components of...

  11. POLYMERIZATION OF ETHYLENE METHYL PHOSPHATE IN THE PRESENCE OF SODIUM POLY(ETHYLENE GLYCOL)ATE

    Institute of Scientific and Technical Information of China (English)

    Jie Wen; Ren-xi Zhuo; Lu Wang

    1999-01-01

    Poly(ethylene methyl phosphate)-poly(ethylene glycol)-poly(ethylene methyl phosphate) triblock copolymers carrying hydroxyl group at both chain ends were synthesized with sodium poly(ethylene glycol)ate as initiator. The effects of the factors such as solvent, amount of the initiator and reaction time were investigated. The copolymers were characterized by IR, 1H-NMR, 1H{31p}-NMR, 13C-NMR, 31P{1H}-NMR, and DSC. High molecular weight of the copolymer and high yield of the polymerization were achieved within 3 min at 25℃. The polymerization process was studied by 31P{1H}-NMR and transesterification was found during longer polymerization time.

  12. Polymerization of ethylene oxide using yttrium isopropoxide

    NARCIS (Netherlands)

    Choi, Young K.; Stevels, W.M.; Ankone, Martinus J.K.; Dijkstra, Pieter J.; Kim, Sung W.; Feijen, Jan

    1996-01-01

    Well defined poly(ethylene oxide)s were prepared using yttrium isopropoxide as an initiator. End group analysis using 1H- and 13C NMR spectroscopy revealed that only polymers with isopropyl ether and hydroxyl end groups were produced. The molecular weight is controlled by the initial amount of

  13. Complete recovery after massive ethylene glycol ingestion.

    Science.gov (United States)

    Curtin, L; Kraner, J; Wine, H; Savitt, D; Abuelo, J G

    1992-06-01

    We treated a 64-year-old man who recovered completely from a massive antifreeze ingestion with ethylene glycol levels well above those of previously described survivors. Rapid and aggressive treatment of the patient with recognized methods, including hemodialysis, resulted in the favorable outcome.

  14. Occurrence of ethylene in anaerobic soil

    Energy Technology Data Exchange (ETDEWEB)

    Smith, K.A.; Restall, S.W.F.

    1971-01-01

    The production of ethylene and other hydrocarbon gases by soils under anaerobic conditions was measured by gas chromatography. Ethylene was the only hydrocarbon gas which occurred in physiologically significant concentrations; more than 20 ppm was found in several soils after 10 days at 20/sup 0/C. These concentrations were considerably higher than those which were known to cause severe reductions in the extension of root axes of some plant species. Experiments with sterilized and unsterilized soil indicated that ethylene was produced by enzyme activity and not by chemical action. The gas was found in soil when the oxygen concentration fell below 2%; total evolution was correlated with organic matter content, and was affected by drying and rewetting and by the growth of plant roots. The rate of production was increased by raising the temperature and by addition of glucose or peptone; high concentrations of nitrate depressed the rate, but sulfate and phosphate had little effect. It is concluded that ethylene may be a significant factor in causing injury to crop plants under waterlogged conditions and also in situations where anaerobic pockets occur within a mainly aerobic soil structure, provided that escape of the gas from the soil is impeded sufficiently to allow inhibitory concentrations to build up in the vicinity of plant roots. 31 references, 7 figures, 3 tables.

  15. Heat Bonding of Irradiated Ethylene Vinyl Acetate

    Science.gov (United States)

    Slack, D. H.

    1986-01-01

    Reliable method now available for joining parts of this difficult-tobond material. Heating fixture encircles ethylene vinyl acetate multiplesocket part, providing heat to it and to tubes inserted in it. Fixtures specially designed to match parts to be bonded. Tube-and-socket bonds made with this technique subjected to tensile tests. Bond strengths of 50 percent that of base material obtained consistently.

  16. Transcriptional regulation of the ethylene response factor LeERF2 in the expression of ethylene biosynthesis genes controls ethylene production in tomato and tobacco.

    Science.gov (United States)

    Zhang, Zhijin; Zhang, Haiwen; Quan, Ruidan; Wang, Xue-Chen; Huang, Rongfeng

    2009-05-01

    Fine-tuning of ethylene production plays an important role in developmental processes and in plant responses to stress, but very little is known about the regulation of ethylene response factor (ERF) proteins in ethylene biosynthesis genes and ethylene production. Identifying cis-acting elements and transcription factors that play a role in this process, therefore, is important. Previously, a tomato (Solanum lycopersicum [f. sp. Lycopersicon esculentum]) ERF protein, LeERF2, an allele of TERF2, was reported to confer ethylene triple response on plants. This paper reports the transcriptional modulation of LeERF2/TERF2 in ethylene biosynthesis in tomato and tobacco (Nicotiana tabacum). Using overexpressing and antisense LeERF2/TERF2 transgenic tomato, we found that LeERF2/TERF2 is an important regulator in the expression of ethylene biosynthesis genes and the production of ethylene. Expression analysis revealed that LeERF2/TERF2 is ethylene inducible, and ethylene production stimulated by ethylene was suppressed in antisense LeERF2/TERF2 transgenic tomato, indicating LeERF2/TERF2 to be a positive regulator in the feedback loop of ethylene induction. Further research showed that LeERF2/TERF2 conservatively modulates ethylene biosynthesis in tobacco and that such regulation in tobacco is associated with the elongation of the hypocotyl and insensitivity to abscisic acid and glucose during germination and seedling development. The effects on ethylene synthesis were similar to those of another ERF protein, TERF1, because TERF1 and LeERF2/TERF2 have overlapping roles in the transcriptional regulation of ethylene biosynthesis in tobacco. Biochemical analysis showed that LeERF2/TERF2 interacted with GCC box in the promoter of NtACS3 and with dehydration-responsive element in the promoter of LeACO3, resulting in transcriptional activation of the genes for ethylene biosynthesis in tomato and tobacco, which is a novel regulatory function of ERF proteins in plant ethylene

  17. Ethylene Inhibits Cell Proliferation of the Arabidopsis Root Meristem.

    Science.gov (United States)

    Street, Ian H; Aman, Sitwat; Zubo, Yan; Ramzan, Aleena; Wang, Xiaomin; Shakeel, Samina N; Kieber, Joseph J; Schaller, G Eric

    2015-09-01

    The root system of plants plays a critical role in plant growth and survival, with root growth being dependent on both cell proliferation and cell elongation. Multiple phytohormones interact to control root growth, including ethylene, which is primarily known for its role in controlling root cell elongation. We find that ethylene also negatively regulates cell proliferation at the root meristem of Arabidopsis (Arabidopsis thaliana). Genetic analysis indicates that the inhibition of cell proliferation involves two pathways operating downstream of the ethylene receptors. The major pathway is the canonical ethylene signal transduction pathway that incorporates CONSTITUTIVE TRIPLE RESPONSE1, ETHYLENE INSENSITIVE2, and the ETHYLENE INSENSITIVE3 family of transcription factors. The secondary pathway is a phosphorelay based on genetic analysis of receptor histidine kinase activity and mutants involving the type B response regulators. Analysis of ethylene-dependent gene expression and genetic analysis supports SHORT HYPOCOTYL2, a repressor of auxin signaling, as one mediator of the ethylene response and furthermore, indicates that SHORT HYPOCOTYL2 is a point of convergence for both ethylene and cytokinin in negatively regulating cell proliferation. Additional analysis indicates that ethylene signaling contributes but is not required for cytokinin to inhibit activity of the root meristem. These results identify key elements, along with points of cross talk with cytokinin and auxin, by which ethylene negatively regulates cell proliferation at the root apical meristem. © 2015 American Society of Plant Biologists. All Rights Reserved.

  18. Enzymatic hydrolysis of poly(ethylene furanoate).

    Science.gov (United States)

    Pellis, Alessandro; Haernvall, Karolina; Pichler, Christian M; Ghazaryan, Gagik; Breinbauer, Rolf; Guebitz, Georg M

    2016-10-10

    The urgency of producing new environmentally-friendly polyesters strongly enhanced the development of bio-based poly(ethylene furanoate) (PEF) as an alternative to plastics like poly(ethylene terephthalate) (PET) for applications that include food packaging, personal and home care containers and thermoforming equipment. In this study, PEF powders of various molecular weights (6, 10 and 40kDa) were synthetized and their susceptibility to enzymatic hydrolysis was investigated for the first time. According to LC/TOF-MS analysis, cutinase 1 from Thermobifida cellulosilytica liberated both 2,5-furandicarboxylic acid and oligomers of up to DP4. The enzyme preferentially hydrolyzed PEF with higher molecular weights but was active on all tested substrates. Mild enzymatic hydrolysis of PEF has a potential both for surface functionalization and monomers recycling. Copyright © 2016 Elsevier B.V. All rights reserved.

  19. Ethylene Oxide Gas Sterilization of Medical Devices.

    Science.gov (United States)

    Shintani, Hideharu

    2017-01-01

     Ethylene oxide gas is an agent in the sterilization of medical devices due to its effectiveness and compatibility with most materials. The advantages and disadvantages, as well as its recommended uses, are explored in this review article. The variables and their relevance on process optimization are described, the types of processing cycles are detailed and emphasis is given to the design and validation of the sterilization process.

  20. Fragrance material review on ethylene brassylate.

    Science.gov (United States)

    McGinty, D; Letizia, C S; Api, A M

    2011-12-01

    A toxicologic and dermatologic review of ethylene brassylate when used as a fragrance ingredient is presented. Ethylene brassylate is a member of the fragrance structural group macrocyclic lactone and lactide derivatives. The fragrance ingredient described herein is one of 12 structurally diverse C14, C15, and C16 compounds that include (7) saturated mono-and (2) saturated di-ester lactones and (3) unsaturated lactones. For the latter, the double bond is not adjacent to (in conjugation with) the ester group. This review contains a detailed summary of all available toxicology and dermatology papers that are related to ethylene brassylate and is not intended as a stand-alone document. Available data were evaluated, then summarized, and includes: physical properties; acute toxicity; skin irritation; skin sensitization; elicitation; phototoxicity; repeated dose; and genotoxicity data. A safety assessment of the entire macrocyclic lactone and lactide derivatives will be published simultaneously with this document. Please refer to Belsito et al. (2011) for an overall assessment of the safe use of this material and all macrocyclic lactone and lactide derivatives in fragrances. Belsito, D., Bickers, D., Bruze, M., Calow, P., Dagli, M., Fryer, A.D., Greim, H., Hanifin, J.H., Miyachi, Y., Saurat, J.H., Sipes, I.G., 2011. A toxicologic and dermatologic assessment of macrocylic lactone and lactide derivatives when used as fragrance ingredients. Copyright © 2011. Published by Elsevier Ltd.

  1. Fragrance material review on ethylene dodecanedioate.

    Science.gov (United States)

    McGinty, D; Letizia, C S; Api, A M

    2011-12-01

    A toxicologic and dermatologic review of ethylene dodecanedioate when used as a fragrance ingredient is presented. Ethylene dodecanedioate is a member of the fragrance structural group macrocyclic lactone and lactide derivatives. The fragrance ingredient described herein is one of 12 structurally diverse C14, C15, and C16 compounds that include (7) saturated mono- and (2) saturated di-ester lactones and (3) unsaturated lactones. For the latter, the double bond is not adjacent to (in conjugation with) the ester group. This review contains a detailed summary of all available toxicology and dermatology papers that are related to ethylene dodecanedioate and is not intended as a stand-alone document. Available data were evaluated, then summarized, and includes: physical properties; acute toxicity; skin irritation; mucous membrane (eye) irritation; skin sensitization; phototoxicity; repeated dose; and genotoxicity data. A safety assessment of the entire macrocyclic lactone and lactide derivatives will be published simultaneously with this document. Please refer to Belsito et al. (2011) for an overall assessment of the safe use of this material and all macrocyclic lactone and lactide derivatives in fragrances. Belsito, D., Bickers, D., Bruze, M., Calow, P., Dagli, M., Fryer, A.D., Greim, H., Hanifin, J.H., Miyachi, Y., Saurat, J.H., Sipes, I.G., 2011. A toxicologic and dermatologic assessment of macrocylic lactone and lactide derivatives when used as fragrance ingredients. Copyright © 2011. Published by Elsevier Ltd.

  2. ROLE OF ETHYLENE IN RESPONSES OF PLANTS TO NITROGEN AVAILABILITY

    Directory of Open Access Journals (Sweden)

    M Iqbal R Khan

    2015-10-01

    Full Text Available Ethylene is a plant hormone involved in several physiological processes and regulates the plant development during the whole life. Stressful conditions usually activate ethylene biosynthesis and signalling in plants. The availability of nutrients, shortage or excess, influences plant metabolism and ethylene plays an important role in plant adaptation under suboptimal conditions. Among the plant nutrients, the nitrogen (N is one the most important mineral element required for plant growth and development. The availability of N significantly influences plant metabolism, including ethylene biology. The interaction between ethylene and N affects several physiological process such as leaf gas exchanges, roots architecture, leaf, fruits and flowers development. Low plant N use efficiency leads to N loss and N deprivation, which affect ethylene biosynthesis and tissues sensitivity, inducing cell damage and ultimately lysis. Plants may respond differently to N availability balancing ethylene production through its signalling network. This review discusses the recent advances in the interaction between N availability and ethylene at whole plant and different organ levels, and explores how N availability induces ethylene biology and plant responses. Exogenously applied ethylene seems to cope the stress conditions and improves plant physiological performance. This can be explained considering the expression of ethylene biosynthesis and signalling genes under different N availability. A greater understanding of the regulation of N by means of ethylene modulation may help to increase N use efficiency and directly influence crop productivity under conditions of limited N availability, leading to positive effects on the environment. Moreover, efforts should be focused on the effect of N deficiency or excess in fruit trees, where ethylene can have detrimental effects especially during postharvest.

  3. Nitric oxide counters ethylene effects on ripening fruits.

    Science.gov (United States)

    Manjunatha, Girigowda; Gupta, Kapuganti J; Lokesh, Veeresh; Mur, Luis A J; Neelwarne, Bhagyalakshmi

    2012-04-01

    Ethylene plays a key role in promoting fruit ripening, so altering its biosynthesis/signaling could be an important means to delay this process. Nitric oxide (NO)-generated signals are now being shown to regulate ethylene pathways. NO signals have been shown to transcriptionally repress the expression of genes involved in ethylene biosynthesis enzymes and post-translationally modify methionine adenosyl transferase (MAT) activity through S-nitrosylation to reduce the availably of methyl groups required to produce ethylene. Additionally, NO cross-talks with plant hormones and other signal molecules and act to orchestrate the suppression of ethylene effects by modulating enzymes/proteins that are generally triggered by ethylene signaling at post-climacteric stage. Thus, medication of endogenous NO production is suggested as a strategy to postpone the climacteric stage of many tropical fruits.

  4. Experimental Study of Ethylene Combustion in a Scramjet Combustor

    Institute of Scientific and Technical Information of China (English)

    XIAO Yin-li; SONG Wen-yan; LE Jia-ling

    2008-01-01

    In this paper the ignition characteristics of gaseous ethylene hydrocarbon fuel is investigated in the supersonic clean airstreams experimental facility with a resistance heater. The generic cavity flame holder is used to create recirculation and promote the fuel/air mixing at the lower wall of the combustor. Three different injection concepts are considered in this research: (1) ethylene injection upstream of the cavity; (2) ethylene and hydrogen injection upstream of the cavity simultaneously; (3) ethylene injection preceded by pilot hydrogen injection. The pilot injection showed to be a supportive tool for holding the flame of the main normal ethylene fuel injection. Therefore, using pilot hydrogen injection and cavity configuration necessitates optimizing the combustor length to ensure the complete combustion and the full liberation of the chemical energy stored in the fuel before exiting the combustor. The present study proved the possibility of igniting the ethylene and maintaining its flame in the supersonic airstreams.

  5. Molecular interactions between ethylene and gibberellic acid pathways in plants

    OpenAIRE

    Rzewuski, Guillaume

    2004-01-01

    Flooding avoidance in deepwater rice is characterised by rapid growth of the youngest internode which allows the plant to keep part of its foliage above the surface of raising flood waters. The primary signal triggering internodal elongation is the phytohormone ethylene which accumulates as a result of increased ethylene biosynthesis and entrapment. Through unknown signalling components, ethylene increases the level of bioactive gibberellins (GA) and responsiveness of the tissue to GA. GA is ...

  6. Sorption interactions between ethylene glycol and carbon nanotubes

    Science.gov (United States)

    Butyrskaya, E. V.; Belyakova, N. V.; Nechaeva, L. S.; Shaposhnik, V. A.; Selemenev, V. F.

    2017-03-01

    The adsorption of ethylene glycol by carbon nanoparticles is studied. Carbon nanoparticles with the highest affinity to ethylene glycol are identified, and an adsorption isotherm is constructed. Based on quantum chemical calculations of the energies of interaction between the sorbate and nanotubes with (4,4) and (6,6) chirality, a change in mechanism is revealed upon the monomolecular adsorption of ethylene glycol on carbon nanotubes, and the adsorption isotherm is thus interpreted.

  7. Ethylene production with engineered Synechocystis sp PCC 6803 strains.

    Science.gov (United States)

    Veetil, Vinod Puthan; Angermayr, S Andreas; Hellingwerf, Klaas J

    2017-02-23

    Metabolic engineering and synthetic biology of cyanobacteria offer a promising sustainable alternative approach for fossil-based ethylene production, by using sunlight via oxygenic photosynthesis, to convert carbon dioxide directly into ethylene. Towards this, both well-studied cyanobacteria, i.e., Synechocystis sp PCC 6803 and Synechococcus elongatus PCC 7942, have been engineered to produce ethylene by introducing the ethylene-forming enzyme (Efe) from Pseudomonas syringae pv. phaseolicola PK2 (the Kudzu strain), which catalyzes the conversion of the ubiquitous tricarboxylic acid cycle intermediate 2-oxoglutarate into ethylene. This study focuses on Synechocystis sp PCC 6803 and shows stable ethylene production through the integration of a codon-optimized version of the efe gene under control of the Ptrc promoter and the core Shine-Dalgarno sequence (5'-AGGAGG-3') as the ribosome-binding site (RBS), at the slr0168 neutral site. We have increased ethylene production twofold by RBS screening and further investigated improving ethylene production from a single gene copy of efe, using multiple tandem promoters and by putting our best construct on an RSF1010-based broad-host-self-replicating plasmid, which has a higher copy number than the genome. Moreover, to raise the intracellular amounts of the key Efe substrate, 2-oxoglutarate, from which ethylene is formed, we constructed a glycogen-synthesis knockout mutant (ΔglgC) and introduced the ethylene biosynthetic pathway in it. Under nitrogen limiting conditions, the glycogen knockout strain has increased intracellular 2-oxoglutarate levels; however, surprisingly, ethylene production was lower in this strain than in the wild-type background. Making use of different RBS sequences, production of ethylene ranging over a 20-fold difference has been achieved. However, a further increase of production through multiple tandem promoters and a broad-host plasmid was not achieved speculating that the transcription strength and

  8. Defining sale ethylene for long term storage of tulip bulbs

    OpenAIRE

    Wild, de, H.P.J.; Peppelenbos, H.W.; Dijkstra, M.H.G.E.; Gude, H.

    2002-01-01

    The maximum ethylene level that can be permitted in storage rooms, without causing damage to tulip bulbs, is not exactly known. Therefore, a zero-tolerance for the presence of ethylene during storage of tulip bulbs is common practice. This results in excessive ventilation and coherent large energy costs. It is questioned whether this is always necessary. In different phases of the storage period the critical levels of ethylene were determined. Bulbs of eight economically important cultivars (...

  9. Genetic Basis of Ethylene Perception and Signal Transduction in Arabidopsis

    Institute of Scientific and Technical Information of China (English)

    Ziqiang Zhu; Hongwei Guo

    2008-01-01

    Ethylene is a simple gaseous hormone in plants. It plays important roles in plant development and stress tolerance. In the presence of ethylene treatment, all ethylene receptors are in an activated form, which can physically interact with CTR1 and consequently recruit CTR1 protein to endoplasmic reticulum membrane to activate it. Activated CTR1 suppresses the downstream signal transduction by an unknown mechanism. Upon binding to its receptors, ethylene will inactivate the receptor/CTR1 module and in turn alleviate their inhibitory effect on two positive regulators acting downstream of CTRI: EIN2 and EIN3. Genetic study reveals that EIN2 is an essential component in the ethylene signaling pathway but its biochemical function remains a mystery. EIN3 is a plant-specific transcription factor and its protein abundance in the nucleus is rapidly induced upon ethylene treatment. In the absence of ethylene signal, EIN3 protein is degraded by an SCF complex containing one of the two F-box proteins EBF1/EBF2 in a 26S proteasome-dependent manner. EIN3 can bind to the promoter sequences of a number of downstream components, such as ERFs, which in turn bind to a GCC box,a cis-element found in many ethylene-regulated defense genes. Ethylene has been shown to also regulate many other hormones' signaling pathways including auxin, abscisic acid and jasmonic acid, implying the existence of complicated signaling networks in the growth, development and defense responses of various plants.

  10. Chemical Genetic Dissection of Brassinosteroid-Ethylene Interaction

    Institute of Scientific and Technical Information of China (English)

    Joshua M.Gendron; Asif Haque; Nathan Gendron; Timothy Chang; Tadao Asami; Zhi-Yong Wang

    2008-01-01

    We undertook a chemical genetics screen to identify chemical inhibitors of brassinosteroid (BR) action.From a chemical library of 10,000 small molecules,one compound was found to inhibit hypocotyl length and activate the expression of a BR-repressed reporter gene (CPD::GUS) in Arabidopsis,and it was named brassinopride (BRP).These effects of BRP could be reversed by co-treatment with brassinolide,suggesting that BRP either directly or indirectly inhibits BR biosynthesis.Interestingly,the compound causes exaggerated apical hooks,similar to that caused by ethylene treatment.The BRP-induced apical hook phenotype can be blocked by a chemical inhibitor of ethylene perception or an ethylene-insensitive mutant,suggesting that,in addition to inhibiting BR,BRP activates ethylene response.Analysis of BRP analogs provided clues about structural features important for its effects on two separate targets in the BR and ethylene pathways.Analyses of the responses of various BR and ethylene mutants to BRP,ethylene,and BR treatments revealed modes of cross-talk between ethylene and BR in dark-grown seedlings.Our results suggest that active downstream BR signaling,but not BR synthesis or a BR gradient,is required for ethylene-induced apical hook formation.The BRP-related compounds can be useful tools for manipulating plant growth and studying hormone interactions.

  11. Ethylene regulates the susceptible response to pathogen infection in tomato.

    Science.gov (United States)

    Lund, S T; Stall, R E; Klee, H J

    1998-03-01

    Ethylene evolution occurs concomitantly with the progression of disease symptoms in response to many virulent pathogen infections in plants. A tomato mutant impaired in ethylene perception-Never ripe-exhibited a significant reduction in disease symptoms in comparison to the wild type after inoculations of both genotypes with virulent bacterial (Xanthomonas campestris pv vesicatoria and Pseudomonas syringae pv tomato) and fungal (Fusarium oxysporum f sp lycopersici) pathogens. Bacterial spot disease symptoms were also reduced in tomato genotypes impaired in ethylene synthesis (1-aminocyclopropane-1-carboxylic acid deaminase) and perception (14893), thereby corroborating a reducing effect for ethylene insensitivity on foliar disease development. The reduction in foliar disease symptoms in Never ripe plants was a specific effect of ethylene insensitivity and was not due to reductions in bacterial populations or decreased ethylene synthesis. PR-1B1 mRNA accumulation in response to X. c. vesicatoria infection was not affected by ethylene insensitivity, indicating that ethylene is not required for defense gene induction. Our findings suggest that broad tolerance of diverse vegetative diseases may be achieved via engineering of ethylene insensitivity in tomato.

  12. Gravitropism in higher plant shoots. I - A role for ethylene

    Science.gov (United States)

    Wheeler, Raymond M.; Salisbury, Frank B.

    1981-01-01

    Two inhibitors of ethylene synthesis, Co(2+) and aminoethoxyvinylglycine (AVG), and two inhibitors of ethylene action, Ag(+) and CO2, are shown to delay the gravitropic response of cocklebur (Xanthium strumarium L.), tomato (Lycopersicon esculentum Mill.), and castor bean (Ricinus communis L.) stems. Gentle shaking on a mechanical shaker does not inhibit the gravitropic response, but vigorous hand shaking for 120 seconds delays the response somewhat. AVG and Ag(+) further delay the response of mechanically stimulated plants. AVG retards the storage of bending energy but not of stimulus. In gravitropism, graviperception may first stimulate ethylene evolution, which may then influence bending directly, or responses involving ethylene could be more indirect.

  13. Controlled release of ethylene via polymeric films for food packaging

    Science.gov (United States)

    Pisano, Roberto; Bazzano, Marco; Capozzi, Luigi Carlo; Ferri, Ada; Sangermano, Marco

    2015-12-01

    In modern fruit supply chain a common method to trigger ripening is to keep fruits inside special chambers and initiate the ripening process through administration of ethylene. Ethylene is usually administered through cylinders with inadequate control of its final concentration in the chamber. The aim of this study is the development of a new technology to accurately regulate ethylene concentration in the atmosphere where fruits are preserved: a polymeric film, containing an inclusion complex of α-cyclodextrin with ethylene, was developed. The complex was prepared by molecular encapsulation which allows the entrapment of ethylene into the cavity of α-cyclodextrin. After encapsulation, ethylene can be gradually released from the inclusion complex and its release rate can be regulated by temperature and humidity. The inclusion complex was dispersed into a thin polymeric film produced by UV-curing. This method was used because is solvent-free and involves low operating temperature; both conditions are necessary to prevent rapid release of ethylene from the film. The polymeric films were characterized with respect to thermal behaviour, crystalline structure and kinetics of ethylene release, showing that can effectively control the release of ethylene within confined volume.

  14. The involvement of ethylene in regulation of Arabidopsis gravitropism

    Science.gov (United States)

    Li, Ning; Zhu, Lin

    Plant gravitropism is a directional response to gravity stimulus. This response involves a com-plex signaling network. Ethylene, a major plant hormone, has been found to modulate grav-itropism. The biosynthesis of ethylene is induced by the gravi-stimulus and the requirement for ethylene during gravitropism is tissue-dependent. While ethylene plays a modulating role in inflorescence stems, the light-grown hypocotyls of Arabidopsis requires ethylene to achieve a maximum gravicurvature. Because both inhibitory and stimulatory effects of ethylene on gravitropism have been overwhelmingly documented, there is a need to postulate a new theory to consolidate the apparently contradictory results. A dual-and-opposing effects (DOE) theory is therefore hypothesized to address how ethylene is involved in regulation of Arabidopsis grav-itropism, in which it is suggested that both stimulatory and inhibitory effects act on the same organ of a plant and co-exist at the same time in a mutually opposing manner. The final out-come of gravitropic response is determined by the dynamic display between the two opposing effects. A prolonged pretreatment of ethylene promotes the gravitropism in both inflorescence and light-grown hypocotyls, while a short ethylene pretreatment inhibits gravitropism. Gener-ally speaking, the inhibitory effect of ethylene is dominant over the expression of the stimula-tory effect in light-grown hypocotyls, whereas the stimulatory effect is dominant in inflorescence stem. Each effect is also positively correlated with concentrations of ethylene and in a time-dependent manner. The stimulatory effect occurs slowly but continues to react after the removal of ethylene, whereas the inhibitory effect takes place abruptly and diminishes shortly after its removal. Forward genetic screening based on the DOE phenotype of ethylene-treated Arabidop-sis has revealed a novel component in gravity signaling pathway: EGY1 (ethylene-dependent gravitropism-deficient and yellow

  15. [Decontamination of some spices by ethylene oxide. Development of 2-chloroethanol and ethylene glycol during the preservation].

    Science.gov (United States)

    Chaigneau, M; Muraz, B

    1993-01-01

    After the disinfection by ethylene oxide and storage by ethylene oxide in definite conditions of 16 spices (parsley, chervil, tarragone, chive, thyme, rosemary, coriander, nutmeg, mace, cinnamon, allspices, clove, pepper), the authors observed the fast loss of residual ethylene oxide and ethyleneglycol. On the contrary, the persistence of 2-chloroethanol was followed up for 6 months. They turn their attention to the toxicity of this compound to ensure the protection of customers.

  16. The effect of nitrate on ethylene biofiltration

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Sang-Hun, E-mail: lee323@alumni.purdue.edu [Department of Agricultural and Biological Engineering, Purdue University, 225 South University St., West Lafayette, 47907-2093 IN (United States); Li, Congna; Heber, Albert J. [Department of Agricultural and Biological Engineering, Purdue University, 225 South University St., West Lafayette, 47907-2093 IN (United States)

    2012-11-30

    Highlights: Black-Right-Pointing-Pointer Ethylene biofiltration strongly depends on nitrate concentrations and media types. Black-Right-Pointing-Pointer We examine reduced N supply can increase ethylene removals in biofilters. Black-Right-Pointing-Pointer Perlite medium is better for ethylene biofiltration than activated carbon medium. - Abstract: This study investigated the effects of filter media types and nitrate (NO{sub 3}{sup -}) concentrations in nutrient solutions on C{sub 2}H{sub 4} biofiltration. A new nutrient solution with zero NO{sub 3}{sup -} concentration was supplied to two perlite-bed biotrickling filters, two perlite-bed biofilters, and two GAC (Granular Activated Carbon)-bed biofilters, while the other with 2 g L{sup -1} of NO{sub 3}{sup -} was used for the other two GAC biofilters. All reactors underwent a total test duration of over 175 days with an EBRT (Empty Bed Residence Time) of 30 s, inlet gas flow rate of 7 L min{sup -1}, and inlet C{sub 2}H{sub 4} concentrations of 20-30 mg m{sup -3}. NO{sub 3}{sup -} concentration and media type significantly affected the C{sub 2}H{sub 4} removal efficiencies in all types of biofiltration. The perlite media with no NO{sub 3}{sup -} achieved C{sub 2}H{sub 4} removal efficiencies 10-50% higher than the others. A NO{sub 3}{sup -} concentration as high as 2 g L{sup -1} in the original nutrient solution may act as an inhibitor that suppresses the growth or activity of C{sub 2}H{sub 4} degraders. In addition, the perlite media resulted in higher C{sub 2}H{sub 4} removal efficiencies than GAC media, because the hydrophilic surface of the perlite leads to a higher moisture content and thus to favorable microbial growth.

  17. ADVANCED CONTROL FOR A ETHYLENE REACTOR

    Directory of Open Access Journals (Sweden)

    Dumitru POPESCU

    2017-06-01

    Full Text Available The main objective of this work is the design and implementation of control solutions for petrochemical processes, namely the control and optimization of a pyrolysis reactor, the key-installation in the petrochemical industry. We present the technological characteristics of this petrochemical process and some aspects about the proposed control system solution for the ethylene plant. Finally, an optimal operating point for the reactor is found, considering that the process has a nonlinear multi-variable structure. The results have been implemented on an assembly of pyrolysis reactors on a petrochemical platform from Romania.

  18. Ethylene production and peroxidase activity in aphid-infested barley.

    Science.gov (United States)

    Argandoña, V H; Chaman, M; Cardemil, L; Muñoz, O; Zúñiga, G E; Corcuera, L J

    2001-01-01

    The purpose of this work was to investigate whether ethylene is involved in the oxidative and defensive responses of barley to the aphids Schizaphis graminum (biotype C) and Rhopalophum padi. The effect of aphid infestation on ethylene production was measured in two barley cultivars (Frontera and Aramir) that differ in their susceptibility to aphids. Ethylene evolution was higher in plants infested for 16 hr than in plants infested for 4 hr in both cultivars. Under aphid infestation, the production of ethylene was higher in cv. Frontera than in Aramir, the more aphid susceptible cultivar. Ethylene production also increases with the degree of infestation. Maximum ethylene evolution was detected after 16 hr when plants were infested with 10 or more aphids. Comparing the two species of aphids, Schizaphis graminum induced more ethylene evolution than Rhopalosiphum padi. Infestation with S. graminum increased hydrogen peroxide content and total soluble peroxidase activity in cv. Frontera, with a maximum level of H2O2 observed after 20 min of infestation and the maximum in soluble peroxidase activity after 30 min of infestation. When noninfested barley seedlings from cv. Frontera were exposed to ethylene, an increase in hydrogen peroxide and in total peroxidase activity was detected at levels similar to those of infested plants from cv. Frontera. When noninfested plants were treated with 40 ppm of ethylene, the maximum levels of H2O2 and soluble peroxidase activity were at 10 and 40 min, respectively. Ethylene also increased the activity of both cell-wall-bound peroxidases types (ionically and covalently bound), comparable with infestation. These results suggest that ethylene is involved in the oxidative responses of barley plants induced by infestation.

  19. Hydrophilic poly(ethylene oxide)-aramide segmented block copolymers

    NARCIS (Netherlands)

    Araichimani, A.; ten Hoopen, Hermina W.M.; Gaymans, R.J.

    2009-01-01

    The present paper discusses block copolymers with segments of either poly(ethylene oxide), poly(propylene oxide), or mixtures of poly(ethylene oxide)/poly(propylene oxide) and monodisperse aramide segments. The length of the polyether segments as well as the concentration of polyethylene oxide was

  20. Evaluation of the Inhalation Carcinogenicity of Ethylene Oxide (Final Report)

    Science.gov (United States)

    EPA has finalized its Evaluation of the Inhalation Carcinogenicity of Ethylene Oxide. This assessment addresses the potential carcinogenicity from long-term inhalation exposure to ethylene oxide. Now final, this assessment updates the carcinogenicity information in EPA’s 1985 Hea...

  1. 21 CFR 177.1310 - Ethylene-acrylic acid copolymers.

    Science.gov (United States)

    2010-04-01

    ... (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) INDIRECT FOOD ADDITIVES: POLYMERS Substances for Use as... this section are not applicable to ethylene-acrylic acid copolymers used in food-packaging adhesives... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ethylene-acrylic acid copolymers. 177.1310...

  2. Price dynamics of crude oil and the regional ethylene markets

    Energy Technology Data Exchange (ETDEWEB)

    Masih, Mansur [Department of Finance and Economics, Center of Research Excellence in Renewable Energy, King Fahd University of Petroleum and Minerals, Dhahran (Saudi Arabia); Algahtani, Ibrahim [Department of Finance and Economics, King Fahd University of Petroleum and Minerals, Dhahran (Saudi Arabia); De Mello, Lurion [Faculty of Business and Economics, Macquarie University, Sydney (Australia)

    2010-11-15

    This paper is the first attempt to investigate: (1) is the crude oil (WTI) price significantly related to the regional ethylene prices in the Naphtha intensive ethylene markets of the Far East, North West Europe, and the Mediterranean? (2) What drives the regional ethylene prices? The paper is motivated by the recent and growing debate on the lead-lag relationship between crude oil and ethylene prices. Our findings, based on the long-run structural modelling approach of Pesaran and Shin, and subject to the limitations of the study, tend to suggest: (1) crude oil (WTI) price is cointegrated with the regional ethylene prices (2) our within-sample error-correction model results tend to indicate that although the ethylene prices in North West Europe and the Mediterranean were weakly endogenous, the Far East ethylene price was weakly exogenous both in the short and long term. These results are consistent, during most of the period under review (2000.1-2006.4) with the surge in demand for ethylene throughout the Far East, particularly in China and South Korea. However, during the post-sample forecast period as evidenced in our variance decompositions analysis, the emergence of WTI as a leading player as well, is consistent with the recent surge in WTI price (fuelled mainly, among others, by the strong hedging activities in the WTI futures/options and refining tightness) reflecting the growing importance of input cost in determining the dynamic interactions of input and product prices. (author)

  3. Defining sale ethylene for long term storage of tulip bulbs

    NARCIS (Netherlands)

    Wild, de H.P.J.; Peppelenbos, H.W.; Dijkstra, M.H.G.E.; Gude, H.

    2002-01-01

    The maximum ethylene level that can be permitted in storage rooms, without causing damage to tulip bulbs, is not exactly known. Therefore, a zero-tolerance for the presence of ethylene during storage of tulip bulbs is common practice. This results in excessive ventilation and coherent large energy

  4. Defining sale ethylene for long term storage of tulip bulbs

    NARCIS (Netherlands)

    Wild, de H.P.J.; Peppelenbos, H.W.; Dijkstra, M.H.G.E.; Gude, H.

    2002-01-01

    The maximum ethylene level that can be permitted in storage rooms, without causing damage to tulip bulbs, is not exactly known. Therefore, a zero-tolerance for the presence of ethylene during storage of tulip bulbs is common practice. This results in excessive ventilation and coherent large energy c

  5. Abscission of mango fruitlets as influenced by enhanced ethylene biosynthesis.

    Science.gov (United States)

    Nunez-Elisea, R; Davenport, T L

    1986-12-01

    Experiments were conducted on developing fruitlet explants of two mango (Mangifera indica L.) cultivars to establish the source and dynamics of ethylene production prior to and during fruitlet abscission. Abscission of all fruits in the samples occurred at approximately 86 and 74 hours postharvest in ;Keitt' and ;Tommy Atkins,' respectively. Increased abscission began 26 hours from harvest and was preceded by enhanced ethylene synthesis. Enhanced ethylene production initiated approximately 48 hours prior to abscission and increased to a maximum near the time of fruitlet abscission. The seed produced the highest amount of ethylene on a per gram fresh weight basis. The pericarp, however, was the main source of ethylene on an absolute basis, since it represented more than 85% of total fruitlet weight. Pedicels containing the abscission zone produced no detectable ethylene prior to or at the moment of abscission. Fumigation of ;Tommy Atkins' fruitlets with 1, 15, or 100 microliters per liter ethylene accelerated abscission by 24 to 36 hours in comparison with unfumigated controls. Diffusion of ethylene from distal fruitlet tissues to the abscission zone triggers the events leading to separation of the fruit from the tree.

  6. A model for the band gap energy of the N-rich GaN{sub 1-x}As{sub x} (0

    Energy Technology Data Exchange (ETDEWEB)

    Zhao Chuanzhen, E-mail: as3262001@yahoo.com.cn [School of Electronics and Information Engineering, Tianjin Polytechnic University Tianjin 300387 (China); Li Nana [School of Textiles, Tianjin Polytechnic University, Tianjin 300387 (China); Key Laboratory of Advanced Textile Composites, Ministry of Education of China, Tianjin 300387 (China); Wei Tong [College of Science, Civil Aviation University of China, Tianjin 300300 (China); Wang Shasha; Lu Keqing [School of Electronics and Information Engineering, Tianjin Polytechnic University Tianjin 300387 (China); Xie Zili [Jiangsu Provincial Key Laboratory of Advanced Photonic and Electronic Materials, Department of Electronic Science and Engineering, Nanjing University, Nanjing 210093 (China)

    2012-12-15

    In this paper, a model for the band gap energy of the N-rich GaNAs (0N-rich GaNAs, The parameters describing the variation of the CBM and the VBM in the N-rich GaNAs are obtained by fitting the experimental data. For the As-rich GaNAs, the parameters in the model are obtained by fitting the experimental data of the band gap energy. It is found that the band gap evolution of the N-rich energy is different from that of the As-rich band gap energy. The model may be used to calculate the band gap energy of other dilute group III-N-V nitrides.

  7. False hyperlactatemia in life-threatening ethylene glycol poisoning.

    Science.gov (United States)

    Riquier, T; Geri, G; Mongardon, N; Bourgogne, E; Pène, F

    2014-04-01

    Ethylene glycol poisoning is rare, but prompt diagnosis is crucial, in order to initiate specific treatments. Herein, we report the case of a patient who was admitted to ICU for coma and extreme metabolic acidosis with unexpected hyperlactatemia on initial ICU blood gas analyzer. Ethylene glycol poisoning was diagnosed, and hyperlactatemia was ruled out on a blood sample sent to the biochemistry department. Interference of blood gas analyzers lactate electrodes with metabolites of ethylene glycol were the source of this apparent hyperlactatemia. Symptoms gradually improved and false hyperlactatemia resolved after renal replacement therapy and fomepizole administration. Time course of ethylene glycol concentration showed similar evolution. After initial confirmation of ethylene glycol presence, this biological interference could thus be used as a surrogate of costly and highly specialised dosages. Copyright © 2014 Société française d’anesthésie et de réanimation (Sfar). Published by Elsevier SAS. All rights reserved.

  8. Understanding tantalum-catalyzed ethylene trimerization: When things go wrong

    KAUST Repository

    Chen, Yin

    2013-06-07

    Ethylene oligomerization to linear low-molecular-mass α-olefins is an open industrial challenge. Ta-based catalysts are promising systems, but the unclear understanding of their behavior prevents systematic advances in the field. We demonstrate here that a well-defined (î -SiO)3Ta III species is able to promote ethylene oligo-/polymerization without any cocatalyst, confirming that the active species in Ta systems corresponds to a TaIII species. DFT calculations on a series of Ta systems ranging from ethylene trimerization to ethylene polymerization catalysts highlight the key factors controlling their experimental behavior. Comparison of these Ta systems allows one to set general rules for the rational development of new ethylene Ta oligomerization catalysts. © 2013 American Chemical Society.

  9. Ethylene production throughout growth and development of plants

    Science.gov (United States)

    Wheeler, Raymond M.; Peterson, Barbara V.; Stutte, Gary W.

    2004-01-01

    Ethylene production by 10 or 20 m2 stands of wheat, soybean, lettuce, potato, and tomato was monitored throughout growth and development in an atmospherically closed plant chamber. Chamber ethylene levels varied among species and rose during periods of canopy expansion and rapid growth for all species. Following this, ethylene levels either declined during seed fill and maturation for wheat and soybean, or remained relatively constant for potato and tomato (during flowering and early fruit development). Lettuce plants were harvested during rapid growth and peak ethylene production. Chamber ethylene levels increased rapidly during tomato ripening, reaching concentrations about 10 times that measured during vegetative growth. The highest ethylene production rates during vegetative growth ranged from 1.6 to 2.5 nmol m-2 d-1 during rapid growth of lettuce and wheat stands, or about 0.3 to 0.5 nmol g-1 fresh weight per hour. Estimates of stand ethylene production during tomato ripening showed that rates reached 43 nmol m-2 d-1 in one study and 93 nmol m-2 d-1 in a second study with higher lighting, or about 50x that of the rate during vegetative growth of tomato. In a related test with potato, the photoperiod was extended from 12 to 24 hours (continuous light) at 58 days after planting (to increase tuber yield), but this change in the environment caused a sharp increase in ethylene production from the basal rate of 0.4 to 6.2 nmol m-2 d-1. Following this, the photoperiod was changed back to 12 h at 61 days and ethylene levels decreased. The results suggest three separate categories of ethylene production were observed with whole stands of plants: 1) production during rapid vegetative growth, 2) production during climacteric fruit ripening, and 3) production from environmental stress.

  10. Ethylene and rooting of mung bean cuttings. The role of auxin induced ethylene synthesis and phase-dependent effects

    NARCIS (Netherlands)

    Klerk, de G.J.M.; Hanecakova, J.

    2008-01-01

    We have re-examined the role of ethylene during rooting of mung bean cuttings. Cuttings were treated for 5 days with a low or a high concentration of NAA (naphthaleneacetic acid). During this 5 days period, we also applied STS (silverthiosulfate, an inhibitor of ethylene action) or ACC (1-aminocyclo

  11. Research tools: ethylene preparation. In: Chi-Kuang Wen editor. Ethylene in plants. Springer Netherlands. Springer Link

    Science.gov (United States)

    Ethylene is a plant hormone that regulates many aspects of plant growth and development, germination, fruit ripening, senescence, sex determination, abscission, defense, gravitropism, epinasty, and more. For experimental purposes, one needs to treat plant material with ethylene and its inhibitors t...

  12. Ethylene and rooting of mung bean cuttings. The role of auxin induced ethylene synthesis and phase-dependent effects

    NARCIS (Netherlands)

    Klerk, de G.J.M.; Hanecakova, J.

    2008-01-01

    We have re-examined the role of ethylene during rooting of mung bean cuttings. Cuttings were treated for 5 days with a low or a high concentration of NAA (naphthaleneacetic acid). During this 5 days period, we also applied STS (silverthiosulfate, an inhibitor of ethylene action) or ACC (1-aminocyclo

  13. Modeling the chemistry of plasma polymerization using mass spectrometry.

    Science.gov (United States)

    Ihrig, D F; Stockhaus, J; Scheide, F; Winkelhake, Oliver; Streuber, Oliver

    2003-04-01

    The goal of the project is a solvent free painting shop. The environmental technologies laboratory is developing processes of plasma etching and polymerization. Polymerized thin films are first-order corrosion protection and primer for painting. Using pure acetylene we get very nice thin films which were not bonded very well. By using air as bulk gas it is possible to polymerize, in an acetylene plasma, well bonded thin films which are stable first-order corrosion protections and good primers. UV/Vis spectroscopy shows nitrogen oxide radicals in the emission spectra of pure nitrogen and air. But nitrogen oxide is fully suppressed in the presence of acetylene. IR spectroscopy shows only C=O, CH(2) and CH(3) groups but no nitrogen species. With the aid of UV/Vis spectra and the chemistry of ozone formation it is possible to define reactive traps and steps, molecule depletion and processes of proton scavenging and proton loss. Using a numerical model it is possible to evaluate these processes and to calculate theoretical mass spectra. Adjustment of theoretical mass spectra to real measurements leads to specific channels of polymerization which are driven by radicals especially the acetyl radical. The estimated theoretical mass spectra show the specific channels of these chemical processes. It is possible to quantify these channels. This quantification represents the mass flow through this chemical system. With respect to these chemical processes it is possible to have an idea of pollutant production processes.

  14. Robust Plasma Polymerized-Titania/Silica Janus Microparticles

    Science.gov (United States)

    2010-04-29

    fluorescent, half- metal -decorated, and half-shelled structures were all demonstrated here as particular examples. Introduction Janus particles result from...for the selective reduction of metal nanoparticles, site-selective grafting, potential biological activity, and generating distinct optical response...of coatings providing for biological activities and biomineralization including Figure 4. AFM topography (left) and phase (right) of plasma coatings

  15. Characterization and properties of plasma polymerized 2-vinylpyridine

    Energy Technology Data Exchange (ETDEWEB)

    Bieg, K.W.; Ottesen, D.K.; Brower, K.L.

    1979-11-01

    The chemical structure, aging, thermal, and adhesive behavior of plasma-deposited 2-vinylpyridine has been investigated. The molecular structure of the plasma polymer is significantly different from the conventional, linear polymer and is strongly dependent on plasma reactor variables. Additional cyano, methyl, and olefinic groups were identified in the plasma polymer, and aromaticity retention was reduced at the more severe (low pressure, high rf power) reactor conditions studied. Post-deposition oxidation occurred, which followed approximately first order kinetics initially (..delta..E approx. 11.6 Kcal/mole, with approx. 25% conversion of aromatic rings to an aromatic ketone in 4.5 months at 23/sup 0/C). Oxidation was significantly reduced in vacuum, inert gas, and hydrogen atmospheres. Thermal weight loss began at relatively low temperatures and appeared to accompany an exothermic, irreversible cross-linking reaction which began at about 100/sup 0/C. Principle low temperature decomposition products were low molecular weight gases (primarily, CO/sub 2/) and 2-methylpyridine. A quantitative tensile-pull adhesion test was developed. Using this technique, the plasma polymer-aluminum cohesive bond strength was found to be 480 psi and was degraded at high humidity levels.

  16. Solid coatings deposited from liquid methyl methacrylate via Plasma Polymerization

    Science.gov (United States)

    Wurlitzer, Lisa; Maus-Friedrichs, Wolfgang; Dahle, Sebastian

    2016-09-01

    The polymerization of methyl methacrylate via plasma discharges is well known today. Usually, plasma-enhanced chemical vapor deposition (PECVD) is used to deposit polymer coatings. Solid coatings are formed out of the liquid phase from methyl methacrylate via dielectric barrier discharge. The formation of the coating proceeds in the gas and the liquid phase. To learn more about the reactions in the two phases, the coatings from MMA monomer will be compared to those from MMA resin. Finally, attenuated total reflection infrared spectroscopy, confocal laser scanning microscopy and X-ray photoelectron spectroscopy are employed to characterize the solid coatings. In conclusion, the plasma enhanced chemical solution deposition is compared to the classical thermal polymerization of MMA.

  17. Producing the Ethylene Signal: Regulation and Diversification of Ethylene Biosynthetic Enzymes.

    Science.gov (United States)

    Booker, Matthew A; DeLong, Alison

    2015-09-01

    Strictly controlled production of ethylene gas lies upstream of the signaling activities of this crucial regulator throughout the plant life cycle. Although the biosynthetic pathway is enzymatically simple, the regulatory circuits that modulate signal production are fine tuned to allow integration of responses to environmental and intrinsic cues. Recently identified posttranslational mechanisms that control ethylene production converge on one family of biosynthetic enzymes and overlay several independent reversible phosphorylation events and distinct mediators of ubiquitin-dependent protein degradation. Although the core pathway is conserved throughout seed plants, these posttranslational regulatory mechanisms may represent evolutionarily recent innovations. The evolutionary origins of the pathway and its regulators are not yet clear; outside the seed plants, numerous biochemical and phylogenetic questions remain to be addressed.

  18. Novel gaseous ethylene binding inhibitor prevents ethylene effects in potted flowering plants

    Energy Technology Data Exchange (ETDEWEB)

    Serek, M.; Reid, M.S. (Univ. of California, Davis, CA (United States). Dept. of Environmental Horticulture); Sisler, E.C. (North Carolina State Univ., Raleigh, NC (United States). Dept. of Biochemistry)

    1994-11-01

    A 6-hour fumigation of flowering Begonia xelatior hybrida Fotsch. Najada' and Rosa', B. xtuberhybrida Voss. Non-Stop', Kalanchoe blossfeldiana Poelln. Tropicana', and Rosa hybrida L. Victory Parade' plants with 1-MCP, (formerly designated as SIS-X), a gaseous nonreversible ethylene binding inhibitor, strongly inhibited exogenous ethylene effects such as bud and flower drop, leaf abscission, and accelerated flower senescence. The inhibitory effects of 1-MCP increased linearly with concentration, and at 20 nl-liter[sup [minus]1] this compound gave equal protection to that afforded by spraying the plants with a 0.5 STS mM solution. Chemical names used: 1-methylcyclopropene (1-MCP), silver thiosulfate (STS).

  19. Self-diffusion coefficients of hexamethylphosphoric triamide and ethylene glycol molecules in ethylene glycol solutions

    Science.gov (United States)

    Idiyatullin, Z. Sh.; Solonina, I. A.; Rodnikova, M. N.; Sirotkin, D. A.

    2017-08-01

    The self-diffusion coefficients of the molecules of hexamethylphosphoric triamide (HMPT) and ethylene glycol (EG) in ethylene glycol solutions in the concentration range 0-16 mol % HMPT and molecules of pure HMPT in the temperature range 30-60°C are measured by the spin-echo method on protons. Activation energies for the corresponding processes of self-diffusion were calculated. The obtained data are discussed in terms of solvophobic effects in the EG-HMPT system. The self-diffusion coefficient of pure HMPT was 0.344 × 10-5 cm2/s at 33.2°C, and the self-diffusion activation energy was 3.86 kcal/mol.

  20. Ethylene: Role in Fruit Abscission and Dehiscence Processes 12

    Science.gov (United States)

    Lipe, John A.; Morgan, Page W.

    1972-01-01

    Two peaks of ethylene production occur during the development of cotton fruitz (Gossypium hirsutum L.). These periods precede the occurrence of young fruit shedding and mature fruit dehiscence, both of which are abscission phenomena and the latter is generally assumed to be part of the total ripening process. Detailed study of the dehiscence process revealed that ethylene production of individual, attached cotton fruits goes through a rising, cyclic pattern which reaches a maximum prior to dehiscence. With detached pecan fruits (Carya illinoensis [Wang.] K. Koch), ethylene production measured on alternate days rose above 1 microliter per kilogram fresh weight per hour before dehiscence began and reached a peak several days prior to complete dehiscence. Ethylene production by cotton and pecan fruits was measured just prior to dehiscence and then the internal concentration of the gas near the center of the fruit was determined. From these data a ratio of production rate to internal concentration was determined which allowed calculation of the approximate ethylene concentration in the intact fruit prior to dehiscence and selection of appropriate levels to apply to fruits. Ethylene at 10 microliters per liter of air appears to saturate dehiscence of cotton, pecan, and okra (Hibiscus esculentus L.) fruits and the process is completed in 3 to 4 days. In all cases some hastening of dehiscence was observed with as little as 0.1 microliter of exogenous ethylene per liter of air. The time required for response to different levels of ethylene was determined and compared to the time course of ethylene production and dehiscence. We concluded that internal levels of ethylene rose to dehiscence-stimulating levels a sufficience time before dehiscence for the gas to have initiated the process. Since our data and calculations indicate that enough ethylene is made a sufficient time before dehiscence, to account for the process, we propose that ethylene is one of the regulators of

  1. Ethylene: role in fruit abscission and dehiscence processes.

    Science.gov (United States)

    Lipe, J A; Morgan, P W

    1972-12-01

    Two peaks of ethylene production occur during the development of cotton fruitz (Gossypium hirsutum L.). These periods precede the occurrence of young fruit shedding and mature fruit dehiscence, both of which are abscission phenomena and the latter is generally assumed to be part of the total ripening process. Detailed study of the dehiscence process revealed that ethylene production of individual, attached cotton fruits goes through a rising, cyclic pattern which reaches a maximum prior to dehiscence. With detached pecan fruits (Carya illinoensis [Wang.] K. Koch), ethylene production measured on alternate days rose above 1 microliter per kilogram fresh weight per hour before dehiscence began and reached a peak several days prior to complete dehiscence. Ethylene production by cotton and pecan fruits was measured just prior to dehiscence and then the internal concentration of the gas near the center of the fruit was determined. From these data a ratio of production rate to internal concentration was determined which allowed calculation of the approximate ethylene concentration in the intact fruit prior to dehiscence and selection of appropriate levels to apply to fruits. Ethylene at 10 microliters per liter of air appears to saturate dehiscence of cotton, pecan, and okra (Hibiscus esculentus L.) fruits and the process is completed in 3 to 4 days. In all cases some hastening of dehiscence was observed with as little as 0.1 microliter of exogenous ethylene per liter of air. The time required for response to different levels of ethylene was determined and compared to the time course of ethylene production and dehiscence. We concluded that internal levels of ethylene rose to dehiscence-stimulating levels a sufficience time before dehiscence for the gas to have initiated the process. Since our data and calculations indicate that enough ethylene is made a sufficient time before dehiscence, to account for the process, we propose that ethylene is one of the regulators of

  2. Radicidation as an alternative for ethylene oxide

    Energy Technology Data Exchange (ETDEWEB)

    Farkas, J. (Koezponti Elelmiszeripari Kutato Intezet, Budapest (Hungary))

    1985-01-01

    The application of ethylene oxide to sterilize dry foodstuff additions proved to be a source of danger both for the personnel of the food preservation industry and for the consumers due to the residue of some chemicals and toxic reaction products which can not be removed from the foodstuff. A more advantageous and less harmful alternative for the reduction of the number of germs is offered by using ionizing radiation. Based on a great number of references, the applicability and effectiveness of radicidation for the preservation of spices, dry vegetable powders, sugar, thickening materials, protein and enzyme products were confirmed. Regarding the economic aspects, this method can be compared with the traditional chemical treatment. Commercial licenses have been issued by the health organizations of 12 countries.

  3. CFD Simulation on Ethylene Furnace Reactor Tubes

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Different mathematical models for ethylene furnace reactor tubes were reviewed. On the basis of these models a new mathematical simulation approach for reactor tubes based on computational fluid dynamics (CFD) technique was presented. This approach took the flow, heat transfer, mass transfer and thermal cracking reactions in the reactor tubes into consideration. The coupled reactor model was solved with the SIMPLE algorithm. Some detailed information about the flow field, temperature field and concentration distribution in the reactor tubes was obtained, revealing the basic characteristics of the hydrodynamic phenomena and reaction behavior in the reactor tubes. The CFD approach provides the necessary information for conclusive decisions regarding the production optimization, the design and improvement of reactor tubes, and the new techniques implementation.

  4. Information theory and the ethylene genetic network.

    Science.gov (United States)

    González-García, José S; Díaz, José

    2011-10-01

    information content in the input message that the cell's genetic machinery is processing during a given time interval. Furthermore, combining Information Theory with the frequency response analysis of dynamical systems we can examine the cell's genetic response to input signals with varying frequencies, amplitude and form, in order to determine if the cell can distinguish between different regimes of information flow from the environment. In the particular case of the ethylene signaling pathway, the amount of information managed by the root cell of Arabidopsis can be correlated with the frequency of the input signal. The ethylene signaling pathway cuts off very low and very high frequencies, allowing a window of frequency response in which the nucleus reads the incoming message as a varying input. Outside of this window the nucleus reads the input message as an approximately non-varying one. This frequency response analysis is also useful to estimate the rate of information transfer during the transport of each new ERF1 molecule into the nucleus. Additionally, application of Information Theory to analysis of the flow of information in the ethylene signaling pathway provides a deeper insight in the form in which the transition between auxin and ethylene hormonal activity occurs during a circadian cycle. An ambitious goal for the future would be to use Information Theory as a theoretical foundation for a suitable model of the information flow that runs at each level and through all levels of biological organization.

  5. Production of ethanol from excess ethylene

    DEFF Research Database (Denmark)

    Kadhim, Adam S.; Carlsen, Kim B.; Bisgaard, Thomas

    2012-01-01

    will focus on the synthetic method, which employs direct hydration of ethylene. A conceptual process design of an ethyl alcohol producing plant is performed in a MSc-level course on Process Design at the Department of Chemical and Biochemical Engineering at DTU. In the designed process, 190 proof ethyl...... is obtained in tasks 1-2. A preliminary process flowsheet is obtained in task 3 using a modified Douglas hierarchical process synthesis method. The next tasks involves making design decisions and then further refining them in tasks 4-7 related to separation factors, reactor operating conditions, product...... with respect to heat integration and process optimization (tasks 10-11). In the final task-12, the environmental impact of the process design is evaluated together with some of the key sustainability measures. In addition to PRO/II, the following software is used: ICAS (for property prediction, analysis...

  6. Bacterial Modulation of Plant Ethylene Levels.

    Science.gov (United States)

    Gamalero, Elisa; Glick, Bernard R

    2015-09-01

    A focus on the mechanisms by which ACC deaminase-containing bacteria facilitate plant growth.Bacteria that produce the enzyme 1-aminocyclopropane-1-carboxylate (ACC) deaminase, when present either on the surface of plant roots (rhizospheric) or within plant tissues (endophytic), play an active role in modulating ethylene levels in plants. This enzyme activity facilitates plant growth especially in the presence of various environmental stresses. Thus, plant growth-promoting bacteria that express ACC deaminase activity protect plants from growth inhibition by flooding and anoxia, drought, high salt, the presence of fungal and bacterial pathogens, nematodes, and the presence of metals and organic contaminants. Bacteria that express ACC deaminase activity also decrease the rate of flower wilting, promote the rooting of cuttings, and facilitate the nodulation of legumes. Here, the mechanisms behind bacterial ACC deaminase facilitation of plant growth and development are discussed, and numerous examples of the use of bacteria with this activity are summarized.

  7. Plants having modified response to ethylene

    Science.gov (United States)

    Meyerowitz, E.M.; Chang, C.; Bleecker, A.B.

    1997-11-18

    The invention includes transformed plants having at least one cell transformed with a modified ETR nucleic acid. Such plants have a phenotype characterized by a decrease in the response of at least one transformed plant cell to ethylene as compared to a plant not containing the transformed plant cell. Tissue and/or temporal specificity for expression of the modified ETR nucleic acid is controlled by selecting appropriate expression regulation sequences to target the location and/or time of expression of the transformed nucleic acid. The plants are made by transforming at least one plant cell with an appropriate modified ETR nucleic acid, regenerating plants from one or more of the transformed plant cells and selecting at least one plant having the desired phenotype. 31 figs.

  8. Production of ethanol from excess ethylene

    DEFF Research Database (Denmark)

    Kadhim, Adam S.; Carlsen, Kim B.; Bisgaard, Thomas

    2012-01-01

    ) and ECON (cost and economic analysis). This design therefore covers all stages of conceptual design, starting from the consideration of qualitative aspects of the process flowsheet and preliminary calculations to detailed process simulations, equipment sizing, costing and an economic evaluation......Ethyl alcohol is one of the most important and used chemicals. Two common routes exist for the production: synthetic route typically based on petroleum feedstock and a fermentation route. The fermentation route comprises the majority of the produced ethyl alcohol. In this work, however, we...... will focus on the synthetic method, which employs direct hydration of ethylene. A conceptual process design of an ethyl alcohol producing plant is performed in a MSc-level course on Process Design at the Department of Chemical and Biochemical Engineering at DTU. In the designed process, 190 proof ethyl...

  9. Photothermal degradation of ethylene/vinylacetate copolymer

    Science.gov (United States)

    Liang, R. H.; Chung, S.; Clayton, A.; Di Stefano, S.; Oda, K.; Hong, S. D.; Gupta, A.

    1983-01-01

    Photothermal degradation studies were conducted on a 'stabilized' formulation of ethylene/vinyl acetate copolymer (EVA) in the temperature range 25-105 C under three different oxygen environments (in open air, with limited access to O2, and in a dark closed stagnant oven). These studies were performed in order to evaluate the utility of EVA as an encapsulation material for photovoltaic modules. Results showed that at low temperature (25 C), slow photooxidation of the polymer occurred via electronic energy transfer involving the UV absorber incorporated in the polymer. However, no changes in the physical properties of the bulk polymer were detected up to 1500 hours of irradiation. At elevated temperatures, leaching and evaporation of the additives occurred, which ultimately resulted in the chemical crosslinking of the copolymer and the formation of volatile photoproducts such as acetic acid.

  10. Information theory and the ethylene genetic network

    Science.gov (United States)

    González-García, José S

    2011-01-01

    information content in the input message that the cell's genetic machinery is processing during a given time interval. Furthermore, combining Information Theory with the frequency response analysis of dynamical systems we can examine the cell's genetic response to input signals with varying frequencies, amplitude and form, in order to determine if the cell can distinguish between different regimes of information flow from the environment. In the particular case of the ethylene signaling pathway, the amount of information managed by the root cell of Arabidopsis can be correlated with the frequency of the input signal. The ethylene signaling pathway cuts off very low and very high frequencies, allowing a window of frequency response in which the nucleus reads the incoming message as a varying input. Outside of this window the nucleus reads the input message as an approximately non-varying one. This frequency response analysis is also useful to estimate the rate of information transfer during the transport of each new ERF1 molecule into the nucleus. Additionally, application of Information Theory to analysis of the flow of information in the ethylene signaling pathway provides a deeper insight in the form in which the transition between auxin and ethylene hormonal activity occurs during a circadian cycle. An ambitious goal for the future would be to use Information Theory as a theoretical foundation for a suitable model of the information flow that runs at each level and through all levels of biological organization. PMID:21897127

  11. Occupational exposure to ethylene oxide and risk of lymphoma.

    Science.gov (United States)

    Kiran, Sibel; Cocco, Pierluigi; Mannetje, Andrea't; Satta, Giannina; D'Andrea, Ileana; Becker, Nikolaus; de Sanjosé, Silvia; Foretova, Lenka; Staines, Anthony; Kleefeld, Silke; Maynadié, Marc; Nieters, Alexandra; Brennan, Paul; Boffetta, Paolo

    2010-11-01

    Ethylene oxide, a high-volume commodity, is an established human carcinogen, although the relevant epidemiologic evidence is limited. We explored the association between occupational exposure to ethylene oxide and risk of lymphoma in a case-control study, including 2347 lymphoma cases first diagnosed in 1998-2004 and 2463 controls, from 6 European countries. The diagnosis of lymphoma was based on the 2001 World Health Organization Classification of lymphoma. Occupational exposure to ethylene oxide was retrospectively assessed by industrial hygienists and occupational physicians based on detailed self-reported information. We modeled risk of lymphoma with unconditional logistic regression analysis as a function of various exposure measures, adjusting for age, sex, and participating center. Thirty-one cases and 27 controls (1.2% of the total study population) were defined as ever having been exposed to ethylene oxide (odds ratio = 1.3 [95% confidence interval [CI] = 0.7-2.1]). Lymphoma risk showed a 4.3-fold increase associated with medium-high frequency of exposure to ethylene oxide (95% CI = 1.4-13). Among major subtypes, chronic lymphocytic leukemia was consistently associated with ethylene oxide exposure, related in a dose-response manner to probability, frequency, and duration of exposure, as well as to cumulative exposure and (less definitively) with exposure intensity. Our results add to the evidence that ethylene oxide is a human carcinogen.

  12. Ethylene Signaling Influences Light-Regulated Development in Pea.

    Science.gov (United States)

    Weller, James L; Foo, Eloise M; Hecht, Valérie; Ridge, Stephen; Vander Schoor, Jacqueline K; Reid, James B

    2015-09-01

    Plant responses to light involve a complex network of interactions among multiple plant hormones. In a screen for mutants showing altered photomorphogenesis under red light, we identified a mutant with dramatically enhanced leaf expansion and delayed petal senescence. We show that this mutant exhibits reduced sensitivity to ethylene and carries a nonsense mutation in the single pea (Pisum sativum) ortholog of the ethylene signaling gene ETHYLENE INSENSITIVE2 (EIN2). Consistent with this observation, the ein2 mutation rescues the previously described effects of ethylene overproduction in mature phytochrome-deficient plants. In seedlings, ein2 confers a marked increase in leaf expansion under monochromatic red, far-red, or blue light, and interaction with phytochromeA, phytochromeB, and long1 mutants confirms that ein2 enhances both phytochrome- and cryptochrome-dependent responses in a LONG1-dependent manner. In contrast, minimal effects of ein2 on seedling development in darkness or high-irradiance white light show that ethylene is not limiting for development under these conditions. These results indicate that ethylene signaling constrains leaf expansion during deetiolation in pea and provide further evidence that down-regulation of ethylene production may be an important component mechanism in the broader control of photomorphogenic development by phytochrome and cryptochrome.

  13. Ethylene oxide removal by sorption on aluminium oxide

    Directory of Open Access Journals (Sweden)

    Arsenijević Zorana Lj.

    2009-01-01

    Full Text Available The dynamics of ethylene oxide sorption and desorption on Al2O3 sorbent were investigated. The investigations of ethylene oxide sorption on Al2O3 show that significant sorption appeared above 125°C. The removal of sorbed ethylene oxide from Al2O3 was achieved by continuous increasing of the temperature up to 450°C in air stream. The analysis of desorbed products show that 90% of adsorbed ethylene oxide is converted to CO2 and the rest consists of the three derivatives of ethylene oxide. The exact composition of desorbed organic products will be determined in further investigation. The desorption temperature profiles point out the presence of two exothermic picks, as was confirmed by detection of CO2 and derivates of ethylene oxide at these temperatures. Investigation of textural characteristics and thermal stability of Al2O3 sorbent show that there are no changes of any characteristics of Al2O3 in sorption/desorption operating temperatures regimes. Only at 700°C the specific surface area of Al2O3 decreases of about 10%. This indicates that the investigated Al2O3 is convenient material for removal of ethylene oxide by sorption.

  14. Localization of the Ethylene-synthesizing System in Apple Tissue.

    Science.gov (United States)

    Mattoo, A K; Lieberman, M

    1977-11-01

    Apple (Malus sp.) slices gradually lost the ability to synthesize ethylene when incubated with a mixture of enzymes that digest cell walls. The released protoplasts did not produce ethylene. The release of protoplasts was faster from climacteric fruit slices than from preclimacteric tissue. In protoplast suspension culture, as new cell wall was deposited (as judged by the intensity of fluorescence of regenerating protoplasts stained with Calcofluor White and the incorporation of labeled myo-inositol into their ethanol-insoluble residue), ethylene synthesis was gradually regained. Restored ethylene synthesis reached a maximum after 80 hours in protoplasts from preclimacteric fruit and in 120 hours in those from climacteric tissue. Addition of methionine (1 mm) to the culture medium was essential for appreciable synthesis of ethylene; and this synthesis was inhibited by the aminoethoxy analogue of rhizobitoxine and by propyl gallate, inhibitors of ethylene synthesis in higher plants. We suggest that the ethylene-synthesizing enzyme system is highly structured in the apple cell and is localized in a cell wall-cell membrane complex.

  15. Shedding light on ethylene metabolism in higher plants

    Directory of Open Access Journals (Sweden)

    Maria Aurineide Rodrigues

    2014-12-01

    Full Text Available Ethylene metabolism in higher plants is regulated by a wide array of endogenous and environmental factors. During most physiological processes, ethylene levels are mainly determined by a strict control of the rate-limiting biosynthetic steps responsible for the production of 1-aminocyclopropane-1-carboxylic acid (ACC and its subsequent conversion to ethylene. Responsible for these reactions, the key enzymes ACC synthase and ACC oxidase are encoded by multigene families formed by members that can be differentially regulated at the transcription and post-translational levels by specific developmental and environmental signals. Among the wide variety of environmental cues controlling plant ethylene production, light quality, duration and intensity have consistently been demonstrated to influence the metabolism of this plant hormone in diverse plant tissues, organs and species. Although still not completely elucidated, the mechanisms underlying the interaction between light signal transduction and ethylene evolution appears to involve a complex network that includes central transcription factors connecting multiple signaling pathways, which can be reciprocally modulated by ethylene itself, other phytohormones, and specific light wavelengths. Accumulating evidence has indicated particular photoreceptors as essential mediators in light-induced signaling cascades affecting ethylene levels. Therefore, this review specifically focuses on discussing the current knowledge of the potential molecular mechanisms implicated in the light-induced responses affecting ethylene metabolism during the regulation of developmental and metabolic plant responses. Besides presenting the state of the art in this research field, some overlooked mechanisms and future directions to elucidate the exact nature of the light-ethylene interplay in higher plants will also be compiled and discussed.

  16. The molecular basis of ethylene signalling in Arabidopsis

    Science.gov (United States)

    Woeste, K.; Kieber, J. J.; Evans, M. L. (Principal Investigator)

    1998-01-01

    The simple gas ethylene profoundly influences plants at nearly every stage of growth and development. In the past ten years, the use of a genetic approach, based on the triple response phenotype, has been a powerful tool for investigating the molecular events that underlie these effects. Several fundamental elements of the pathway have been described: a receptor with homology to bacterial two-component histidine kinases (ETR1), elements of a MAP kinase cascade (CTR1) and a putative transcription factor (EIN3). Taken together, these elements can be assembled into a simple, linear model for ethylene signalling that accounts for most of the well-characterized ethylene mediated responses.

  17. Membrane-based gas separation of ethylene/ethylene oxide mixtures for product enrichment in microreactor technology.

    Science.gov (United States)

    Schiewe, B; Staudt-Bickel, C; Vuin, A; Wegner, G

    2001-04-17

    For the off-gas product separation in an ethylene oxide microreactor, new concepts need to be developed. Instead of using the technical process of low-temperature distillation, the performance of gas separation through a dense polymeric membrane was investigated. Different noncrosslinked and crosslinked 6FDA-based polyimides and copolyimides (6FDA=4,4'-hexafluoroisopropylidene diphthalic anhydride) were screened as potential membrane materials. The polymer structure of the membrane material was found to influence the solubility of ethylene oxide and ethylene. The introduction of polar substituents in the polymer backbone increases the solubility selectivity drastically. For permeation experiments in the same pressure range, a novel setup was developed using microstructured membrane supports. With this device, different polymer membranes were tested with respect to the pure gas permeability of ethylene oxide and ethylene as a function of the feed pressure, so that plasticisation effects could be discussed. For different polyimides and copolyimides, ideal ethylene oxide/ethylene selectivities between 3 and 4.5 were found combined with permeabilities between 1.8 and 80.8 barrer.

  18. Elimination of columnar microstructure in N-face InAlN, lattice-matched to GaN, grown by plasma-assisted molecular beam epitaxy in the N-rich regime

    Energy Technology Data Exchange (ETDEWEB)

    Ahmadi, Elaheh; Wienecke, Steven; Keller, Stacia; Mishra, Umesh K. [Department of Electrical and Computer Engineering, University of California, Santa Barbara, California 93106 (United States); Shivaraman, Ravi; Wu, Feng; Kaun, Stephen W.; Speck, James S. [Materials Department, University of California, Santa Barbara, California 93106 (United States)

    2014-02-17

    The microstructure of N-face InAlN layers, lattice-matched to GaN, was investigated by scanning transmission electron microscopy and atom probe tomography. These layers were grown by plasma-assisted molecular beam epitaxy (PAMBE) in the N-rich regime. Microstructural analysis shows an absence of the lateral composition modulation that was previously observed in InAlN films grown by PAMBE. A room temperature two-dimensional electron gas (2DEG) mobility of 1100 cm{sup 2}/V s and 2DEG sheet charge density of 1.9 × 10{sup 13} cm{sup −2} was measured for N-face GaN/AlN/GaN/InAlN high-electron-mobility transistors with lattice-matched InAlN back barriers.

  19. Identification of rice ethylene-response mutants and characterization of MHZ7/OsEIN2 in distinct ethylene response and yield trait regulation.

    Science.gov (United States)

    Ma, Biao; He, Si-Jie; Duan, Kai-Xuan; Yin, Cui-Cui; Chen, Hui; Yang, Chao; Xiong, Qing; Song, Qing-Xin; Lu, Xiang; Chen, Hao-Wei; Zhang, Wan-Ke; Lu, Tie-Gang; Chen, Shou-Yi; Zhang, Jin-Song

    2013-11-01

    Ethylene plays essential roles in adaptive growth of rice plants in water-saturating environment; however, ethylene signaling pathway in rice is largely unclear. In this study, we report identification and characterization of ethylene-response mutants based on the specific ethylene-response phenotypes of etiolated rice seedlings, including ethylene-inhibited root growth and ethylene-promoted coleoptile elongation, which is different from the ethylene triple-response phenotype in Arabidopsis. We establish an efficient system for screening and a set of rice mutants have been identified. Genetic analysis reveals that these mutants form eight complementation groups. All the mutants show insensitivity or reduced sensitivity to ethylene in root growth but exhibit differential responses in coleoptile growth. One mutant group mhz7 has insensitivity to ethylene in both root and coleoptile growth. We identified the corresponding gene by a map-based cloning method. MHZ7 encodes a membrane protein homologous to EIN2, a central component of ethylene signaling in Arabidopsis. Upon ethylene treatment, etiolated MHZ7-overexpressing seedlings exhibit enhanced coleoptile elongation, increased mesocotyl growth and extremely twisted short roots, featuring enhanced ethylene-response phenotypes in rice. Grain length was promoted in MHZ7-transgenic plants and 1000-grain weight was reduced in mhz7 mutants. Leaf senescent process was also affected by MHZ7 expression. Manipulation of ethylene signaling may improve adaptive growth and yield-related traits in rice.

  20. Ethylene decomposition at undercoordinated sites on Cu(410).

    Science.gov (United States)

    Kravchuk, Tatyana; Vattuone, Luca; Burkholder, Luke; Tysoe, Wilfred T; Rocca, Mario

    2008-09-24

    We demonstrate the selective, low-temperature chemistry of ethylene on the strongly undercoordinated sites of Cu(410) by investigating its adsorption by high-resolution electron energy loss spectroscopy (HREELS), X-ray photoelectron spectroscopy (XPS), and temperature-programmed desorption (TPD). After dosing ethylene at approximately 110 K, apart from the expected pi-bonded species adsorbed on terraces, di-sigma-bonded ethylene and carbon are formed at the step edges. The latter product results from the complete dehydrogenation of ethylene and blocks sites for further dissociation and/or di-sigma-adsorption. However, these processes can be restored merely by heating the sample to 900 K, by causing the carbon to diffuse into the bulk. The presented results support the relevance of copper-based catalysts for the steam reforming process.

  1. USE OF THERAPEUTIC PLASMAPHERESIS IN ETHYLENE DIBRO MIDE INTOXICATION

    Directory of Open Access Journals (Sweden)

    Dolly

    2013-02-01

    Full Text Available ABSTRACT: In view of high incidence of mortality with Ethylen e dibromide poisoning, a retrospective study was conducted, with objectives t o compare demographic, toxicological & clinical outcome in patients treated conservatively and those who underwent therapeutic plasmapheresis

  2. Copolymerization Kinetics of Ethylene Oxide and Propylene Oxide

    Institute of Scientific and Technical Information of China (English)

    尹红; 陈志荣

    2002-01-01

    The copolymerization kinetics of ethylene oxide and propylene oxide in an atomizing-circulation reactorunder semi-continuous operation is studied which is of great importance for molecular designation. The kineticparameters are obtained by numerical optimization of the kinetic model.

  3. Ethylene binding to Au/Cu alloy nanoparticles

    Science.gov (United States)

    Gammage, Michael D.; Stauffer, Shannon; Henkelman, Graeme; Becker, Michael F.; Keto, John W.; Kovar, Desiderio

    2016-11-01

    Weak chemisorption of ethylene has been shown to be an important characteristic in the use of metals for the separation of ethylene from ethane. Previously, density functional theory (DFT) has been used to predict the binding energies of various metals and alloys, with Ag having the lowest chemisorption energy amongst the metals and alloys studied. Here Au/Cu alloys are investigated by a combination of DFT calculations and experimental measurements. It is inferred from experiments that the binding energy between a Au/Cu alloy and ethylene is lower than to either of the pure metals, and DFT calculations confirm that this is the case when Au segregates to the particle surface. Implications of this work suggest that it may be possible to further tune the binding energy with ethylene by compositional and morphological control of films produced from Au-surface segregated alloys.

  4. A natural frameshift mutation in Campanula EIL2 correlates with ethylene insensitivity in flowers

    DEFF Research Database (Denmark)

    Jensen, Line; Hegelund, Josefine Nymark; Olsen, Andreas

    2016-01-01

    BACKGROUND: The phytohormone ethylene plays a central role in development and senescence of climacteric flowers. In ornamental plant production, ethylene sensitive plants are usually protected against negative effects of ethylene by application of chemical inhibitors. In Campanula, flowers...... are sensitive to even minute concentrations of ethylene. RESULTS: Monitoring flower longevity in three Campanula species revealed C. portenschlagiana (Cp) as ethylene sensitive, C. formanekiana (Cf) with intermediate sensitivity and C. medium (Cm) as ethylene insensitive. We identified key elements in ethylene...

  5. Links Between Ethylene and Sulfur Nutrition—A Regulatory Interplay or Just Metabolite Association?

    OpenAIRE

    Wawrzynska, Anna; Moniuszko, Grzegorz; Sirko, Agnieszka

    2015-01-01

    Multiple reports demonstrate associations between ethylene and sulfur metabolisms, however the details of these links have not yet been fully characterized; the links might be at the metabolic and the regulatory levels. First, sulfur-containing metabolite, methionine, is a precursor of ethylene and is a rate limiting metabolite for ethylene synthesis; the methionine cycle contributes to both sulfur and ethylene metabolism. On the other hand, ethylene is involved in the complex response networ...

  6. Ethylene epoxidation catalyzed by chlorine-promoted silver oxide

    Energy Technology Data Exchange (ETDEWEB)

    Ozbek, M O; Onal, I [Chemical Engineering Department, Middle East Technical University, 06531, Ankara (Turkey); Van Santen, R A, E-mail: r.a.v.santen@tue.nl [Chemical Engineering and Chemistry Department, Eindhoven University of Technology, 5600 MB, Eindhoven (Netherlands)

    2011-10-12

    It is demonstrated that, on a silver oxide surface, direct formation of ethylene oxide (EO) through the reaction between gas phase ethylene and surface oxygen is possible. The direct reaction channel produces EO selectively without competing with acetaldehyde (AA) formation. The oxometallacycle (OMC) forms on an oxygen vacant surface and reduces EO selectivity. Cl adsorption removes these surface vacant sites and hence prevents the formation of the OMC intermediate.

  7. Ethylene Emission of Apples Treated with 1-Methylcyclopropene During Storage

    Directory of Open Access Journals (Sweden)

    Melnyk Oleksandr

    2014-09-01

    Full Text Available The effect of post-harvest application of 1-methylcyclopropene (1-MCP on ethylene emission in early-winter apple (cv. ‘Calville’, winter (‘Gloster’, ‘Golden Delicious’ and ‘Jonagold’, and late-winter cultivars (‘Granny Smith’, ‘Idared’ and ‘Reinette Simirenko’ w as investigated. The fruits were picked at a commercial harvest time and half of them were treated with 1-MCP (‘SmartFresh™’ 0.068 gm-3 for 24 h at 5 °C. Then both groups of apples were placed in a common storage at the temperature of 2 °C. The intensity of fruit ethylene emission (rate of ethylene production was measured and 1 -MCP inhibition index was calculated. During storage, activity of ethylene emission by control apples of ‘Calville’ and ‘Golden Delicious’ showed typical climacteric pattern, while the intensity of ethylene emission of apples of other cultivars only increased gradually. The change of ethylene activity of early-winter apple cv. ‘Calville’ and winter cv. ‘Jonagold’, both treated with 1-MCP after harvest, had exponential character, especially actively increasing after 3 months of storage. At the same time ethylene emission of 1 -MCP treated fruits of other cultivars changed steadily to a low level and was effectively suppressed during the whole 6-month period of storage in normal atmosphere. The value of inhibition index of fruits treated by 1-MCP confirmed the consistent restoration of the ability to ethylene synthesis and thus to post-harvest ripening of some apples cultivars.

  8. Workers exposed to ethylene oxide: a follow up study.

    Science.gov (United States)

    Gardner, M J; Coggon, D; Pannett, B; Harris, E C

    1989-12-01

    A cohort study has been carried out of 2876 men and women with potential exposure to ethylene oxide. Subjects were identified from employment records at four companies that have produced or used ethylene oxide since the 1950s and at eight hospitals which have had ethylene oxide sterilising units since the 1960s. The cohort represents a substantial proportion of the British workforce with a history of occupational exposure to ethylene oxide. Industrial hygiene data were not available before 1977, but since then time weighted average exposures have been less than 5 ppm in almost all jobs and less than 1 ppm in many. Past exposures were probably somewhat higher. In contrast to some previous studies, no clear excess of leukaemia (three deaths observed, 2.09 expected) and no increase in stomach cancer (five deaths observed, 5.95 expected) were found. This discrepancy with earlier reports may be due in part to differences in levels of exposure. Total cancer mortality was similar to that expected from national and local death rates. Some specific cancers showed small excesses but their relevance to ethylene oxide exposure is doubtful. Again, contrary to some earlier reports, no excess of cardiovascular disease was found. This study does not exclude the possibility that ethylene oxide is a human carcinogen but suggests that any risk of cancer from currently permitted occupational exposures is small.

  9. Efficient use of Ethylene Oxide in Vinyl Sulphone Industry

    Directory of Open Access Journals (Sweden)

    Bhavi M. Pandya, Prof. Bharat H. Shah

    2013-04-01

    Full Text Available Vinyl sulphone production includes mainly 4 unit processes which are Chlorosulphonation, Reduction, Condensation, and Esterification. Vinyl sulphone is the highest export dye intermediate. Vinyl sulphone industry in India received a set back in the late nineties due to world competition and insistence on environmental regulations by the controlling authorities. Excess of ethylene oxide is used in condensation, Which is hazardous and it is used in excess as large quantity of Ethylene oxide is reacted with water as a side reaction forming glycols, and also ethylene oxide is soluble in water. So ethylene oxide is wasted in water and increases the volume of reactor. This paper describes to minimize the quantity of water which is causing excess use of ethylene oxide in condensation reaction. Before condensation reaction there are two unit processes Chlorosulphonation and reduction from which we try to limit the quantity of water, so that water coming to condensation reaction is minimized to reduce the side reaction of ethylene oxide and water.

  10. Ethylene Formation by Catalytic Dehydration of Ethanol with Industrial Considerations

    Directory of Open Access Journals (Sweden)

    Ho-Shing Wu

    2012-12-01

    Full Text Available Ethylene is the primary component in most plastics, making it economically valuable. It is produced primarily by steam-cracking of hydrocarbons, but can alternatively be produced by the dehydration of ethanol, which can be produced from fermentation processes using renewable substrates such as glucose, starch and others. Due to rising oil prices, researchers now look at alternative reactions to produce green ethylene, but the process is far from being as economically competitive as using fossil fuels. Many studies have investigated catalysts and new reaction engineering technologies to increase ethylene yield and to lower reaction temperature, in an effort to make the reaction applicable in industry and most cost-efficient. This paper presents various lab synthesized catalysts, reaction conditions, and reactor technologies that achieved high ethylene yield at reasonable reaction temperatures, and evaluates their practicality in industrial application in comparison with steam-cracking plants. The most promising were found to be a nanoscale catalyst HZSM-5 with 99.7% ethylene selectivity at 240 °C and 630 h lifespan, using a microreactor technology with mechanical vapor recompression, and algae-produced ethanol to make ethylene.

  11. KINETICS OF NON-ISOTHERMAL CRYSTALLIZATION OF POLY (ETHYLENE TEREPHTHALATE) MODIFIED BY POLY (ETHYLENE GLYCOL)

    Institute of Scientific and Technical Information of China (English)

    ZHANG Zhiying; WU Shizhen; DU Yinghua; CAO Zhenlin

    1991-01-01

    The non-isothermal crystallization kinetics of poly(ethylene terephthalate) (PET) modified by poly (ethlene glycol) (PEG) were determined by DSC. The dual linear regression method was used to evaluate the relationship between the reciprocal of t1/2 ( the half life of crystallization ) and the appropriate temperature variable. The parameters such as the activation energy (Ed) for transport,the equilibrium melting temperature (T0m),the nucleation parameter (ψ),the maximum crystallization temperature (Tc, max ) , and the kinetic crystallizability (G) for the copolyesters were obtained. The influence of the PEG content in PET chains on the parameters characterizing crystallization kinetics and crystallization thermodynamics was discussed.

  12. Biosynthesis of ethylene glycol in Escherichia coli.

    Science.gov (United States)

    Liu, Huaiwei; Ramos, Kristine Rose M; Valdehuesa, Kris Niño G; Nisola, Grace M; Lee, Won-Keun; Chung, Wook-Jin

    2013-04-01

    Ethylene glycol (EG) is an important platform chemical with steadily expanding global demand. Its commercial production is currently limited to fossil resources; no biosynthesis route has been delineated. Herein, a biosynthesis route for EG production from D-xylose is reported. This route consists of four steps: D-xylose → D-xylonate → 2-dehydro-3-deoxy-D-pentonate → glycoaldehyde → EG. Respective enzymes, D-xylose dehydrogenase, D-xylonate dehydratase, 2-dehydro-3-deoxy-D-pentonate aldolase, and glycoaldehyde reductase, were assembled. The route was implemented in a metabolically engineered Escherichia coli, in which the D-xylose → D-xylulose reaction was prevented by disrupting the D-xylose isomerase gene. The most efficient construct produced 11.7 g L(-1) of EG from 40.0 g L(-1) of D-xylose. Glycolate is a carbon-competing by-product during EG production in E. coli; blockage of glycoaldehyde → glycolate reaction was also performed by disrupting the gene encoding aldehyde dehydrogenase, but from this approach, EG productivity was not improved but rather led to D-xylonate accumulation. To channel more carbon flux towards EG than the glycolate pathway, further systematic metabolic engineering and fermentation optimization studies are still required to improve EG productivity.

  13. China's first home-made large ethylene unit put into operation in Daqing%China's first home-made large ethylene unit put into operation in Daqing

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    On October 5, the newly built 600kt/a ethylene unit at Daqing Petrochemical, a key part of the company's 1.2Mt/a ethylene expansion/upgrading project, turned out qualified products, indicating the successful industrialization of the packaged technology for China's first home-made large ethylene unit. This enables China to be independent from importing technologies for ethylene production which lasted for halfa century.

  14. Tuning ethylene gas adsorption via metal node modulation: Cu-MOF-74 for a high ethylene deliverable capacity.

    Science.gov (United States)

    Liao, Yijun; Zhang, Lin; Weston, Mitchell H; Morris, William; Hupp, Joseph T; Farha, Omar K

    2017-08-17

    M-MOF-74s were examined for potential applications in ethylene abatement and/or storage/delivery. Due to labile binding resulting from a Jahn-Teller distortion, Cu-MOF-74 exhibits a gradual initial uptake that, in turn, translates into the highest deliverable capacity among the MOFs examined (3.6 mmol g(-1)). In contrast, Co-MOF-74 is the most promising candidate for ethylene abatement due to the sharp uptake at low pressure.

  15. Coadsorption of ethylene and potassium on Pt(111). 1. Formation of a. pi. -bonded state of ethylene

    Energy Technology Data Exchange (ETDEWEB)

    Windham, R.G.; Bartram, M.E.; Koel, B.E.

    1988-05-19

    High resolution electron energy spectroscopy (HREELS), temperature-programmed desorption (TPD), and ultraviolet photoelectron spectroscopy (UPS) have been combined to study the effect of preadsorbed potassium on the adsorption of ethylene on the platinum(111) single-crystal surface. Addition of potassium increases the relative amount of reversible ethylene adsorption at 100 K/. Upon coadsorption with potassium, the authors also observe a new low-temperature ethylene desorption state at 150 K, with E/sub d/ = 5-9 kcal mol/sup -1/, which is about one-half the binding energy of ethylene adsorbed on clean Pt(111). The origin of this new desorption state is the formation of a weakly interacting ethylene species, which is only slightly distorted from the gas-phase hybridization, as determined primarily by vibrational spectroscopy. An explanation is given for these effects in which the increased charge density at the platinum surface due to coadsorbed potassium inhibits the strong sigma-donation of adsorbed ethylene to platinum and greatly reduces the chemisorption bond strength.

  16. Surface Plasmon Resonance Sensor Based on Ethylene Tetra-Fluoro-Ethylene Hollow Fiber

    Directory of Open Access Journals (Sweden)

    Pan Chen

    2015-11-01

    Full Text Available A new kind of hollow fiber surface plasmon resonance sensor (HF-SPRS based on the silver-coated ethylene tetra-fluoro-ethylene (ETFE hollow fiber (HF is presented. The ETFE HF-SPRS is fabricated, and its performance is investigated experimentally by measuring the transmission spectra of the sensor when filled by liquid sensed media with different refractive indices (RIs. Theoretical analysis based on the ray transmission model is also taken to evaluate the sensor. Because the RI of ETFE is much lower than that of fused silica (FSG, the ETFE HF-SPRS can extend the lower limit of the detection range of the early reported FSG HF-SPRS from 1.5 to 1.42 approximately. This could greatly enhance the application potential of HF-SPRS. Moreover, the joint use of both ETFE and FSG HF-SPRSs can cover a wide detection range from 1.42 to 1.69 approximately with high sensitivities larger than 1000 nm/RIU.

  17. Evaluation of workers exposed to ethylene glycol monomethyl ether and ethylene glycol monomethyl ether acetate.

    Science.gov (United States)

    Park, Jiyoung; Yoon, Chungsik; Byun, Hyaejeong; Kim, Yangho; Park, Donguk; Ha, Kwonchul; Lee, Sang man; Park, Sungki; Chung, Eunkyo

    2012-01-01

    Ethylene glycol monomethyl ether (EGME) and ethylene glycol monomethyl ether acetate (EGMEA) are widely used in industries as solvents for coatings, paint and ink, but exposure data are limited because they are minor components out of mixed solvents, as well as because of inconsistency in desorption solvent use. The objective of this study was to investigate the worker exposure profile of EGME and EGMEA. Our study investigated 27 workplaces from June to September 2008 and detected EGME and EGMEA in 20 and 13, respectively. Both personal and area sampling were conducted using a charcoal tube to collect EGME and EGMEA. Gas chromatography with a flame ionization detector was used to analyze these compounds after desorption using a mixture of methylene chloride and methanol. The arithmetic mean concentrations of EGME and EGMEA during periods of full work shifts were 2.59 ppm and 0.33 ppm, respectively. The exposure levels were lower than the Korean Ministry of Labor (MOL) OEL (5 ppm) but higher than the ACGIH TLV (0.1 ppm). In general, the working environments were poor and required much improvement, including the use of personal protective equipment. Only 50% of the workplaces had local exhaust ventilation systems in operation. The average capture velocity of the operating local exhaust ventilation systems was 0.27 m/s, which did not meet the legal requirement of 0.5 m/s. Educating workers to clearly understand the handling and use of hazardous chemicals and improving working conditions are strongly suggested.

  18. Peptides interfering with protein-protein interactions in the ethylene signaling pathway delay tomato fruit ripening

    Science.gov (United States)

    Bisson, Melanie M. A.; Kessenbrock, Mareike; Müller, Lena; Hofmann, Alexander; Schmitz, Florian; Cristescu, Simona M.; Groth, Georg

    2016-08-01

    The plant hormone ethylene is involved in the regulation of several processes with high importance for agricultural applications, e.g. ripening, aging and senescence. Previous work in our group has identified a small peptide (NOP-1) derived from the nuclear localization signal of the Arabidopsis ethylene regulator ETHYLENE INSENSITIVE-2 (EIN2) C-terminal part as efficient inhibitor of ethylene responses. Here, we show that NOP-1 is also able to efficiently disrupt EIN2-ETR1 complex formation in tomato, indicating that the NOP-1 inhibition mode is conserved across plant species. Surface application of NOP-1 on green tomato fruits delays ripening similar to known inhibitors of ethylene perception (MCP) and ethylene biosynthesis (AVG). Fruits treated with NOP-1 showed similar ethylene production as untreated controls underlining that NOP-1 blocks ethylene signaling by targeting an essential interaction in this pathway, while having no effect on ethylene biosynthesis.

  19. Auxin and ethylene induce flavonol accumulation through distinct transcriptional networks.

    Science.gov (United States)

    Lewis, Daniel R; Ramirez, Melissa V; Miller, Nathan D; Vallabhaneni, Prashanthi; Ray, W Keith; Helm, Richard F; Winkel, Brenda S J; Muday, Gloria K

    2011-05-01

    Auxin and ethylene are key regulators of plant growth and development, and thus the transcriptional networks that mediate responses to these hormones have been the subject of intense research. This study dissected the hormonal cross talk regulating the synthesis of flavonols and examined their impact on root growth and development. We analyzed the effects of auxin and an ethylene precursor on roots of wild-type and hormone-insensitive Arabidopsis (Arabidopsis thaliana) mutants at the transcript, protein, and metabolite levels at high spatial and temporal resolution. Indole-3-acetic acid (IAA) and 1-aminocyclopropane-1-carboxylic acid (ACC) differentially increased flavonol pathway transcripts and flavonol accumulation, altering the relative abundance of quercetin and kaempferol. The IAA, but not ACC, response is lost in the transport inhibitor response1 (tir1) auxin receptor mutant, while ACC responses, but not IAA responses, are lost in ethylene insensitive2 (ein2) and ethylene resistant1 (etr1) ethylene signaling mutants. A kinetic analysis identified increases in transcripts encoding the transcriptional regulators MYB12, Transparent Testa Glabra1, and Production of Anthocyanin Pigment after hormone treatments, which preceded increases in transcripts encoding flavonoid biosynthetic enzymes. In addition, myb12 mutants were insensitive to the effects of auxin and ethylene on flavonol metabolism. The equivalent phenotypes for transparent testa4 (tt4), which makes no flavonols, and tt7, which makes kaempferol but not quercetin, showed that quercetin derivatives are the inhibitors of basipetal root auxin transport, gravitropism, and elongation growth. Collectively, these experiments demonstrate that auxin and ethylene regulate flavonol biosynthesis through distinct signaling networks involving TIR1 and EIN2/ETR1, respectively, both of which converge on MYB12. This study also provides new evidence that quercetin is the flavonol that modulates basipetal auxin transport.

  20. Effects of Ethephon, Ethylene, and 2,4-Dichlorophenoxyacetic Acid on Asexual Embryogenesis in Vitro12

    Science.gov (United States)

    Tisserat, Brent; Murashige, Toshio

    1977-01-01

    Asexual embryogenesis in Daucus carota L. `Queen Anne's Lace' callus was suppressed by Ethephon, ethylene, and 2,4-dichlorophenoxyacetic acid (2,4-D). The Ethephon effect could be attributed to volatile and nonvolatile substances. The volatile component was probably entirely ethylene. Ethylene was liberated in the cultures in direct proportion to Ethephon added to the medium. Autoclaving of Ethephon caused a substantial decrease of measurable ethylene. Continuous exposure of callus to 5 μl/l ethylene depressed somatic cell embryogenesis, but not markedly. Depression of embryogenesis by 2,4-D was unrelated to ethylene evolution. PMID:16660109

  1. Massive ethylene glycol poisoning triggers osmotic demyelination syndrome.

    Science.gov (United States)

    Ahmed, Azeemuddin; Tschetter, Paul A; Krasowski, Matthew D; Engelman, Amy

    2014-03-01

    Ethylene glycol is a toxic organic solvent implicated in thousands of accidental and intentional poisonings each year. Osmotic demyelination syndrome (ODS) is traditionally known as a complication of the rapid correction of hyponatremia. Our aim was to describe how patients with ethylene glycol toxicity may be at risk for developing ODS in the absence of hyponatremia. A 64-year old female patient was comatose upon presentation and laboratory results revealed an anion gap of 39, a plasma sodium of 150 mEq/L, a plasma potassium of 3.5 mEq/L, an osmolal gap of 218, an arterial blood gas pH of 7.02, whole blood lactate of 32 mEq/L, no measurable blood ethanol, and a plasma ethylene glycol concentration of 1055.5 mg/dL. The patient was treated for ethylene glycol poisoning with fomepizole and hemodialysis. Despite having elevated serum sodium levels, the patient's hospital course was complicated by ODS. Rapid changes in serum osmolality from ethylene glycol toxicity or its subsequent treatment can cause ODS independent of serum sodium levels. Copyright © 2014 Elsevier Inc. All rights reserved.

  2. Novel and existing data for a future physiological toxicokinetic model of ethylene and its metabolite ethylene oxide in mouse, rat, and human.

    Science.gov (United States)

    Filser, Johannes Georg; Artati, Anna; Li, Qiang; Pütz, Christian; Semder, Brigitte; Klein, Dominik; Kessler, Winfried

    2015-11-05

    The olefin ethylene is a ubiquitously found gas. It originates predominantly from plants, combustion processes and industrial sources. In mammals, inhaled ethylene is metabolized by cytochrome P450-dependent monooxygenases, particularly by cytochrome P450 2E1, to ethylene oxide, an epoxide that directly alkylates proteins and DNA. Ethylene oxide was mutagenic in vitro and in vivo in insects and mammals and carcinogenic in rats and mice. A physiological toxicokinetic model is a most useful tool for estimating the ethylene oxide burden in ethylene-exposed rodents and humans. The only published physiological toxicokinetic model for ethylene and metabolically produced ethylene oxide is discussed. Additionally, existing data required for the development of a future model and for testing its predictive accuracy are reviewed and extended by new gas uptake studies with ethylene and ethylene oxide in B6C3F1 mice and with ethylene in F344 rats. Copyright © 2015 The Authors. Published by Elsevier Ireland Ltd.. All rights reserved.

  3. Properties of very n -rich He isotopes

    Energy Technology Data Exchange (ETDEWEB)

    Fomichev, A.S.; Golovkov, M.S.; Ter-Akopian, G.M.; Oganessian, Yu.Ts.; Gorshkov, V.A.; Krupko, S.A.; Rodin, A.M.; Sidorchuk, S.I.; Slepnev, R.S.; Stepantsov, S.V.; Chudoba, V. [JINR, Flerov Laboratory of Nuclear Reactions, Dubna (Russian Federation); Grigorenko, L.V. [JINR, Flerov Laboratory of Nuclear Reactions, Dubna (Russian Federation); RRC, The Kurchatov Institute, Moscow (Russian Federation); Wolski, R. [JINR, Flerov Laboratory of Nuclear Reactions, Dubna (Russian Federation); Henryk Niewodniczanski, Institute of Nuclear Physics PAS, Cracow (Poland); Korsheninnikov, A.A.; Kuzmin, E.A.; Nikolskii, E.Yu.; Novatskii, B.G.; Stepanov, D.N. [RRC, The Kurchatov Institute, Moscow (Russian Federation); Roussel-Chomaz, P. [GANIL, BP 5027, Caen Cedex 5 (France); Mittig, W. [GANIL, BP 5027, Caen Cedex 5 (France); NSCL Michigan State University, East Lansing, MI (United States); Pang, D. [JINR, Flerov Laboratory of Nuclear Reactions, Dubna (Russian Federation); GANIL, BP 5027, Caen Cedex 5 (France); Ninane, A. [University of Louvain, IPN and CRC, Louvain-la-Neuve (Belgium); Hanappe, F. [Universite Libre de Bruxelles, PNTPM, Bruxelles (Belgium); Stuttge, L. [IN2P3/Universite Louis Pasteur, Institut Pluridisciplinaire Hubert Curien, Strasbourg (France); Yukhimchuk, A.A.; Perevozchikov, V.V.; Vinogradov, Yu.I.; Grishechkin, S.K.; Zlatoustovskiy, S.V. [RNFC All-Russian Research, Institute of Experimental Physics, Sarov (Russian Federation)

    2009-12-15

    Low-energy spectra of the {sup 8,} {sup 10}He nuclei were investigated in the (t, p) -type reactions at small centre-of-mass angles using {proportional_to} 25 AMeV beams of {sup 6}He and {sup 8}He nuclei. The 0 {sup +} ground state (g.s.) of {sup 8}He and excited states, 2 {sup +} at 3.6-3.9MeV and (1 {sup +}) at 5.3-5.5MeV, were populated with cross-sections of 200, 100-250, and 90-125 {mu}b/sr, respectively. To account for a near-threshold anomaly observed in the {sup 8}He spectrum the population of a 1 {sup -} continuum (soft dipole excitation) was considered. The lowest-energy group of events in the {sup 10}He spectrum was observed at {proportional_to} 3 MeV with a cross-section of {proportional_to} 140 {mu}b/sr. This result is consistent with the previously reported observation of {sup 10}He providing a new g.s. position for {sup 10}He at about 3MeV. (orig.)

  4. Temporally Varying Ethylene Emission on Jupiter

    Science.gov (United States)

    Romani, Paul N.; Jennings, Donald E.; Bjoraker, Gordon L.; Sada, Pedro V.; McCabe. Geprge; Boyle, Robert J.

    2008-01-01

    Ethylene (C2H4) emission has been measured in the poles and equator of Jupiter. The 949 cm(sup -1) spectra were recorded with a high resolution spectrometer at the McMath-Pierce telescope at Kitt Peak in October-November 1998 and at the Infrared Telescope Facility at Mauna Kea in June 2000. C2H4 is an important product of methane chemistry in the outer planets. Knowledge of its abundance can help discriminate among the various proposed sets of CH4 photolysis branching ratios at Ly-alpha, and determine the relative importance of the reaction pathways that produce C2H2 and C2H6. In the equatorial region the C2H4 emission is weak, and we were only able to detect it at high air-mass, near the limb. We derive a peak equatorial molar abundance of C2H4 of 4.5 x 10(exp -7) - 1.7 x 10(exp -6) near 2.2 x 10(exp -3) mbar, with a total column of 5.7 x 10(exp 14) - 2.2 x 10(exp 15) molecules cm(exp -2) above 10 mbar depending upon choice of thermal profile. We observed enhanced C2H4 emission from the poles in the regions where auroras are seen in X-ray, UV, and near infrared images. In 2000 we measured a short-term change in the distribution of polar C2H4 emission; the emission in the north IR auroral "hot spot" decreased by a factor of three over a two-day interval. This transient its contribution peak at 5-10 microbar suggests that the polar e is primarily a thermal effect coupled with vertical transport. Comparing our observations from Kitt Peak and Mauna Kea shows that the C2H4 emission of the northern non-"hot spot" auroral regions did not change over the three-year period while that in the southern polar regions decreased.

  5. Assessment of a semi-quantitative screening method for diagnosis of ethylene glycol poisoning.

    Science.gov (United States)

    Sankaralingam, Arun; Thomas, Annette; James, David R; Wierzbicki, Anthony S

    2017-07-01

    Background Ethylene glycol poisoning remains a rare but important presentation to acute toxicology units. Guidelines recommended that ethylene glycol should be available as an 'urgent' test within 4 h, but these are difficult to deliver in practice. This study assessed a semi-quantitative enzymatic spectrophotometric assay for ethylene glycol compatible with automated platforms. Methods The ethylene glycol method was assessed in 21 samples from patients with an increased anion gap and metabolic acidosis not due to ethylene glycol ingestion, and seven samples known to contain ethylene glycol. All samples were analysed in random order in a blinded manner to their origin on a laboratory spectrophotometer. Results In this study, seven samples were known to contain ethylene glycol at concentrations >100 mg/L. The method correctly identified all seven samples as containing ethylene glycol. No false-positives were observed. Thirteen samples gave clear negative results. Ethylene glycol was present at ethylene glycol concentration against results obtained when the samples had been analysed using the quantitative method on an automated analyser showed a good correlation (R = 0.84) but with an apparent under-recovery. Conclusions A semi-quantitative assay for ethylene glycol was able to discriminate well between samples containing ethylene glycol and those with other causes of acidosis. It is a practical small-scale assay for rapid identification of cases of ethylene glycol poisoning.

  6. High selective ethane cracking to ethylene at Veba Oel plant

    Energy Technology Data Exchange (ETDEWEB)

    Sundaram, K.M. [ABB Lummus Crest, Bloomfield, NJ (United States); Albano, J.V. [ABB Lummus Crest, Bloomfield, NJ (United States); Goldmann, K. [Ruhr Oel GmbH, Muenchsmuenster (Germany)

    1995-03-01

    Thermal dehydrogenation is the only commercially feasible route to produce ethylene from ethane even today. Like many dehydrogenation reactions, this is also equilibrium limited under typical operating conditions. Factors such as feed impurities, operating conditions, reactor design and surface conditions influence the selectivity to ethylene. These are illustrated in the paper based on experimental data. Based on these results and through the use of rigorous kinetic models to describe the cracking furnace, a state of the art heater was built to crack ethane at Veba Oel. This furnace achieved high selectivity to ethylene ad long run lengths. The improvement in selectivity over conventional long residence time coils was significant and the deterioration of selectivity from start of run to end of run due to coke deposition in the new design was negligible. This heater also achieved long run lengths with high olefin contents in the ethane feed. (orig.)

  7. Structure and Mechanical Properties of Ethylene-butene Copolymers

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The crystallinity of ethylene-butene copolymers prepared by copolymerization of ethylene and butene in the presence of a new highly active catalyst was studied by means of DSC, WAXD and DMA. The results show that the melting temperature, the crystallinity and the crystallite size decreased with increasing the content of butene in the copolymers. The copolymers have a high degree of branching, the butene segments are mainly in the amorphous regions of the copolymers, while the polyethylene sequence forms crystal phase acting as crosslinking bondage between the molecules at room temperature. The ethylene-butene copolymers have a low modulus, a low stress and a high strain analogous to the stress-strain behavior of non-cross thermoplastic elastomer.

  8. COMPOSITIONAL HETEROGENEITY OF ETHYLENE OXIDE-BUTYLENE TEREPHTHALATE SEGMENTED COPOLYMER

    Institute of Scientific and Technical Information of China (English)

    De-zhu Ma; Dong-sheng Li; Ming-chuan Zhao; Mo-zhen Wang; Ran Ye; Xiao-lie Luo

    1999-01-01

    A series of ethylene oxide-butylene terephthalate (EOBT) segmented copolymers with different soft segment length and hard segment content were synthesized. The compositional heterogeneity was studied by solvent extraction. The results show that the compositional heterogeneity increases when soft segment length and hard segment content increase. The compositional heterogeneity is also reflected in the crystallization behavior and morphology of soft and hard segment in EOBT segmented copolymer. The more compositional heterogeneous the EOBT segmented copolymer is, the more different the morphology and the crystallization behavior between separated fractions. Compared with ethylene oxide-ethylene terephthalate (EOET) segmented copolymer, compositional heterogeneity in EOBT segmented copolymer is weaker. But the compositional heterogeneity in EOBT segmented copolymer with long soft segment and high hard segment content is still obvious.

  9. Transcriptional Regulation of the Ethylene Response Factor LeERF2 in the Expression of Ethylene Biosynthesis Genes Controls Ethylene Production in Tomato and Tobacco1[W][OA

    Science.gov (United States)

    Zhang, Zhijin; Zhang, Haiwen; Quan, Ruidan; Wang, Xue-Chen; Huang, Rongfeng

    2009-01-01

    Fine-tuning of ethylene production plays an important role in developmental processes and in plant responses to stress, but very little is known about the regulation of ethylene response factor (ERF) proteins in ethylene biosynthesis genes and ethylene production. Identifying cis-acting elements and transcription factors that play a role in this process, therefore, is important. Previously, a tomato (Solanum lycopersicum [f. sp. Lycopersicon esculentum]) ERF protein, LeERF2, an allele of TERF2, was reported to confer ethylene triple response on plants. This paper reports the transcriptional modulation of LeERF2/TERF2 in ethylene biosynthesis in tomato and tobacco (Nicotiana tabacum). Using overexpressing and antisense LeERF2/TERF2 transgenic tomato, we found that LeERF2/TERF2 is an important regulator in the expression of ethylene biosynthesis genes and the production of ethylene. Expression analysis revealed that LeERF2/TERF2 is ethylene inducible, and ethylene production stimulated by ethylene was suppressed in antisense LeERF2/TERF2 transgenic tomato, indicating LeERF2/TERF2 to be a positive regulator in the feedback loop of ethylene induction. Further research showed that LeERF2/TERF2 conservatively modulates ethylene biosynthesis in tobacco and that such regulation in tobacco is associated with the elongation of the hypocotyl and insensitivity to abscisic acid and glucose during germination and seedling development. The effects on ethylene synthesis were similar to those of another ERF protein, TERF1, because TERF1 and LeERF2/TERF2 have overlapping roles in the transcriptional regulation of ethylene biosynthesis in tobacco. Biochemical analysis showed that LeERF2/TERF2 interacted with GCC box in the promoter of NtACS3 and with dehydration-responsive element in the promoter of LeACO3, resulting in transcriptional activation of the genes for ethylene biosynthesis in tomato and tobacco, which is a novel regulatory function of ERF proteins in plant ethylene

  10. Rotational spectrum of the tetrafluoromethane-ethylene oxide

    Science.gov (United States)

    Gou, Qian; Feng, Gang; Evangelisti, Luca; Caminati, Walther

    2017-05-01

    The rotational spectrum of one conformer of the CF4-ethylene oxide complex has been measured by using a pulsed jet Fourier-transform microwave spectrometer. The observed conformer is stabilized by a CF3⋯O halogen bond, with a distance rC⋯O of ∼3.341 Å. No experimental evidence of the internal rotation of CF4 with respect to ethylene oxide has been observed, but it is expected to be almost free (V3 ∼ 14 cm-1 from ab initio calculations).

  11. [Tunable diode laser absorption spectroscopy system for trace ethylene detection].

    Science.gov (United States)

    Pan, Wei-Dong; Zhang, Jia-Wei; Dai, Jing-Min; Song, Kai

    2012-10-01

    Tunable diode laser absorption spectroscopy (TDLAS) was characterized by ultra-narrow line width laser and wavelength modulation, which makes it possible to scan a single absorption line. TDLAS has an advantage in trace gas analysis for its high resolution, high sensitivity and quick response. The 1 626.8 nm absorption line of ethylene was selected for detecting by analyzing its absorption line characteristic. The TDLAS system was developed with a white type multi-pass cell, combined with wavelength modulation and harmonic detection. Ethylene concentration ranges from 20 to 1 200 ppmv were tested using this system. The estimated detection limit of the system is 10 ppmv.

  12. Ethylene Control of Fruit Ripening: Revisiting the Complex Network of Transcriptional Regulation.

    Science.gov (United States)

    Liu, Mingchun; Pirrello, Julien; Chervin, Christian; Roustan, Jean-Paul; Bouzayen, Mondher

    2015-12-01

    The plant hormone ethylene plays a key role in climacteric fruit ripening. Studies on components of ethylene signaling have revealed a linear transduction pathway leading to the activation of ethylene response factors. However, the means by which ethylene selects the ripening-related genes and interacts with other signaling pathways to regulate the ripening process are still to be elucidated. Using tomato (Solanum lycopersicum) as a reference species, the present review aims to revisit the mechanisms by which ethylene regulates fruit ripening by taking advantage of new tools available to perform in silico studies at the genome-wide scale, leading to a global view on the expression pattern of ethylene biosynthesis and response genes throughout ripening. Overall, it provides new insights on the transcriptional network by which this hormone coordinates the ripening process and emphasizes the interplay between ethylene and ripening-associated developmental factors and the link between epigenetic regulation and ethylene during fruit ripening.

  13. Numerical Study on Laminar Burning Velocity and Flame Stability of Premixed Methane/Ethylene/Air Flames

    Institute of Scientific and Technical Information of China (English)

    陈珊珊; 蒋勇; 邱榕; 安江涛

    2012-01-01

    A numerical study on premixed methane/ethylene/air flames with various ethylene fractions and equivalence ratios was conducted at room temperature and atmospheric pressure. The effects of ethylene addition on laminar burning velocity, flame structure and flame stability under the condition of lean burning were investigated. The results show that the laminar burning velocity increases with ethylene fraction, especially at a large equivalence ratio. More ethylene addition gives rise to higher concentrations of H, O and OH radicals in the flame, which significantly promotes chemical reactions, and a linear correlation exists between the laminar burning velocity and the maximum H + OH concentration in the reaction zone. With the increase of ethylene fraction, the adiabatic flame temperature is raised, while the inner layer temperature becomes lower, contributing to the enhancement of combustion. Markstein length and Markstein number, representative of the flame stability, increase as more ethylene is added, indicating the tendency of flame stability to improve with ethylene addition.

  14. Syntheses of Poly(ethylene oxide) Macromonomers Carrying Tertiary Amine and Quaternary Ammonium End Groups

    National Research Council Canada - National Science Library

    Senyo, Takamichi; Atago, Yuji; Liang, Huanan; Shen, Renhua; Ito, Koichi

    2003-01-01

    p-Vinylbenzyl alcohol, partially alkoxidated with potassium naphthalene, was used successfully to initiate living polymerization of ethylene oxide to afford α-p-vinylbenzyl-ω-hydroxy poly(ethylene oxide) (PEO) macromonomers. The ω...

  15. Effect of Comonomer Ethylene on Plateau Modulus of Crystalline Ethylene-propylene Random Copolymer with Broad Molecular Weight Distribution

    Institute of Scientific and Technical Information of China (English)

    丁健; 徐日炜; 丁雪佳; 余鼎声

    2005-01-01

    Ethylene-propylene random copolymer with ultra-high molecular weight (UHPPR) and broad molecular weight distribution (MWD) was prepared with Ziegler-Natta catalyst. The viscoelastic behavior of UHPPR has been investigated by means of oscillatory rheometer at 180, 200 and 220℃. The loss modulus (G"""") curves of 180 and 200℃ present a pronounced maximum at 38.10 and 84.70r/s, respectively, For the first time, this makes it possible to directly determine the plateau modulus ( GN0 ) of crystalline ethylene-propylene random copolymer with broad MWD in a certain experimental temperature G""""(w) curve. The plateau modulus of UHPPR is 4.51×105 and 3.67×105 Paat 180 and 200℃ respectively, increasing with random incorporation of comonomer ethylene into the molecular chains and being independent of molecular weight.

  16. The tomato ethylene receptors NR and LeETR4 are negative regulators of ethylene response and exhibit functional compensation within a multigene family.

    Science.gov (United States)

    Tieman, D M; Taylor, M G; Ciardi, J A; Klee, H J

    2000-05-09

    The plant hormone ethylene is involved in many developmental processes, including fruit ripening, abscission, senescence, and leaf epinasty. Tomato contains a family of ethylene receptors, designated LeETR1, LeETR2, NR, LeETR4, and LeETR5, with homology to the Arabidopsis ETR1 ethylene receptor. Transgenic plants with reduced LeETR4 gene expression display multiple symptoms of extreme ethylene sensitivity, including severe epinasty, enhanced flower senescence, and accelerated fruit ripening. Therefore, LeETR4 is a negative regulator of ethylene responses. Reduced expression of this single gene affects multiple developmental processes in tomato, whereas in Arabidopsis multiple ethylene receptors must be inactivated to increase ethylene response. Transgenic lines with reduced NR mRNA levels exhibit normal ethylene sensitivity but elevated levels of LeETR4 mRNA, indicating a functional compensation of LeETR4 for reduced NR expression. Overexpression of NR in lines with lowered LeETR4 gene expression eliminates the ethylene-sensitive phenotype, indicating that despite marked differences in structure these ethylene receptors are functionally redundant.

  17. Maize and Arabidopsis ARGOS Proteins Interact with Ethylene Receptor Signaling Complex, Supporting a Regulatory Role for ARGOS in Ethylene Signal Transduction[OPEN

    Science.gov (United States)

    Shi, Jinrui; Wang, Hongyu; Habben, Jeffrey E.

    2016-01-01

    The phytohormone ethylene regulates plant growth and development as well as plant response to environmental cues. ARGOS genes reduce plant sensitivity to ethylene when overexpressed in transgenic Arabidopsis (Arabidopsis thaliana) and maize (Zea mays). A previous genetic study suggested that the endoplasmic reticulum and Golgi-localized maize ARGOS1 targets the ethylene signal transduction components at or upstream of CONSTITUTIVE TRIPLE RESPONSE1, but the mechanism of ARGOS modulating ethylene signaling is unknown. Here, we demonstrate in Arabidopsis that ZmARGOS1, as well as the Arabidopsis ARGOS homolog ORGAN SIZE RELATED1, physically interacts with Arabidopsis REVERSION-TO-ETHYLENE SENSITIVITY1 (RTE1), an ethylene receptor interacting protein that regulates the activity of ETHYLENE RESPONSE1. The protein-protein interaction was also detected with the yeast split-ubiquitin two-hybrid system. Using the same yeast assay, we found that maize RTE1 homolog REVERSION-TO-ETHYLENE SENSITIVITY1 LIKE4 (ZmRTL4) and ZmRTL2 also interact with maize and Arabidopsis ARGOS proteins. Like AtRTE1 in Arabidopsis, ZmRTL4 and ZmRTL2 reduce ethylene responses when overexpressed in maize, indicating a similar mechanism for ARGOS regulating ethylene signaling in maize. A polypeptide fragment derived from ZmARGOS8, consisting of a Pro-rich motif flanked by two transmembrane helices that are conserved among members of the ARGOS family, can interact with AtRTE1 and maize RTL proteins in Arabidopsis. The conserved domain is necessary and sufficient to reduce ethylene sensitivity in Arabidopsis and maize. Overall, these results suggest a physical association between ARGOS and the ethylene receptor signaling complex via AtRTE1 and maize RTL proteins, supporting a role for ARGOS in regulating ethylene perception and the early steps of signal transduction in Arabidopsis and maize. PMID:27268962

  18. 78 FR 24738 - Ethylene Oxide; Receipt of Application for Emergency Exemption, Solicitation of Public Comment

    Science.gov (United States)

    2013-04-26

    ... AGENCY Ethylene Oxide; Receipt of Application for Emergency Exemption, Solicitation of Public Comment... Service (APHIS) to use the pesticide ethylene oxide (CAS No. 75-21-8) to sterilize the interior surfaces... APHIS has requested the EPA Administrator to issue a quarantine exemption for the use of ethylene oxide...

  19. 46 CFR 154.1730 - Ethylene oxide: Loading and off loading.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Ethylene oxide: Loading and off loading. 154.1730... Operating Requirements § 154.1730 Ethylene oxide: Loading and off loading. (a) The master shall ensure that before ethylene oxide is loaded into a cargo tank: (1) The tank is thoroughly clean, dry, and free of...

  20. 21 CFR 172.808 - Copolymer condensates of ethylene oxide and propylene oxide.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Copolymer condensates of ethylene oxide and propylene oxide. 172.808 Section 172.808 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH... ethylene oxide and propylene oxide. Copolymer condensates of ethylene oxide and propylene oxide may be...

  1. 78 FR 46260 - Sorbitan Monooleate Ethylene Oxide Adduct; Exemption From the Requirement of a Tolerance

    Science.gov (United States)

    2013-07-31

    ... AGENCY 40 CFR Part 180 Sorbitan Monooleate Ethylene Oxide Adduct; Exemption From the Requirement of a... ethylene oxide adduct'' and as ``polysorbate 80'') when used as an inert ingredient in antimicrobial... residues of sorbitan monooleate ethylene oxide adduct. DATES: This regulation is effective July 31, 2013...

  2. 40 CFR 180.1040 - Ethylene glycol; exemption from the requirement of a tolerance.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Ethylene glycol; exemption from the... Exemptions From Tolerances § 180.1040 Ethylene glycol; exemption from the requirement of a tolerance. Ethylene glycol as a component of pesticide formulations is exempt from the requirement of a tolerance when...

  3. 21 CFR 177.1315 - Ethylene-1, 4-cyclohexylene dimethylene terephthalate copolymers.

    Science.gov (United States)

    2010-04-01

    ... production or added to impart desired physical or technical properties. (b) Specifications: Ethylene-1,4... ethylene glycol and 1 to 15 mole percent of 1,4-cyclohexane-di-methanol (70 percent trans isomer, 30... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ethylene-1, 4-cyclohexylene dimethylene...

  4. Genome Wide Identification and Expression Profiling of Ethylene Receptor Genes during Soybean Nodulation.

    Science.gov (United States)

    Wang, Youning; Yuan, Jinhong; Yang, Wei; Zhu, Lin; Su, Chao; Wang, Xiaodi; Wu, Haiyan; Sun, Zhengxi; Li, Xia

    2017-01-01

    It has long been known that the gaseous plant hormone ethylene plays a key role in nodulation in legumes. The perception of ethylene by a family of five membrane-localized receptors is necessary to trigger the ethylene signaling pathway, which regulates various biological responses in Arabidopsis. However, a systematic analysis of the ethylene receptors in leguminous plants and their roles in nodule development is lacking. In this study, we performed a characterization of ethylene receptor genes based on the latest Glycine max genome sequence and a public microarray database. Eleven ethylene receptor family genes were identified in soybean through homology searches, and they were divided into two subgroups. Exon-intron analysis showed that the gene structures are highly conserved within each group. Further analysis of their expression patterns showed that these ethylene receptor genes are differentially expressed in various soybean tissues and organs, including functional nodules. Notably, the ethylene receptor genes showed different responses to rhizobial infection and Nod factors, suggesting a possible role for ethylene receptors and ethylene signaling in rhizobia-host cell interactions and nodulation in soybean. Together, these data indicate the functional divergence of ethylene receptor genes in soybean, and that some of these receptors mediate nodulation, including rhizobial infection, nodule development, and nodule functionality. These findings provide a foundation for further elucidation of the molecular mechanism by which the ethylene signaling pathway regulates nodulation in soybean, as well as other legumes.

  5. 21 CFR 177.1360 - Ethylene-vinyl acetate-vinyl alcohol copolymers.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ethylene-vinyl acetate-vinyl alcohol copolymers... acetate-vinyl alcohol copolymers. Ethylene-vinyl acetate-vinyl alcohol copolymers (CAS Reg. No. 26221-27-2... accordance with the following prescribed conditions: (a) Ethylene-vinyl acetate-vinyl alcohol copolymers...

  6. Adverse health effects of ethylene oxide and occupational exposure limits.

    Science.gov (United States)

    Sheikh, K

    1984-01-01

    The proposed revision of the US standard for occupational exposure to ethylene oxide has recently been topical and controversial. Most of the recent experimental and epidemiological evidence of health effects, which provoked lowering the permissible exposure limit, appears to be unreliable and insufficient for risk assessment.

  7. Analysis of the complexation reaction between Ag+ and ethylene

    NARCIS (Netherlands)

    Nymeijer, Kitty; Visser, Tymen; Brilman, Wim; Wessling, Matthias

    2004-01-01

    In the present work the reversible, bimolecular (1,1) reaction between ethylene and Ag+ in concentrated AgNO3(aq) solutions is analyzed. Due to interactions between the positively charged Ag+ ions and the negatively charged NO3- ions, the silver nitrate is not completely dissociated and the actual f

  8. Enhanced Ionic Conductivity of Poly(Ethylene Imine) Phosphate

    DEFF Research Database (Denmark)

    Senadeera, G.K.R.; Careem, M.A.; Skaarup, Steen;

    1996-01-01

    The conductivity of mixtures of phosphoric acid with poly(ethylene imine) has been studied, and it was found that the conductivity of such mixtures with high acid content can be enhanced by the addition of highly dispersed silica (fumed silica). At the same time, silica addition increases the sti...

  9. Polyamine levels and tomato fruit development: possible interaction with ethylene.

    Science.gov (United States)

    Saftner, R A; Baldi, B G

    1990-02-01

    Fruits of tomato, Lycopersicon esculentum Mill. cv Liberty, ripen slowly and have a prolonged keeping quality. Ethylene production and the levels of polyamines in pericarp of cv Liberty, Pik Red, and Rutgers were measured in relation to fruit development. Depending on the stage of fruit development, Liberty produced between 16 and 38% of the ethylene produced by Pik Red and Rutgers. The polyamines putrescine, spermidine, and spermine were present in all cultivars. Cadaverine was detected only in Rutgers. Levels of putrescine and spermidine declined between the immature and mature green stages of development and prior to the onset of climacteric ethylene production. In Pik Red and Rutgers, the decline persisted, whereas in Liberty, the putrescine level increased during ripening. Ripe pericarp of Liberty contained about three and six times more free (unconjugated) polyamines than Pik Red and Rutgers, respectively. No pronounced changes in spermidine or cadaverine occurred during ripening. The increase in the free polyamine level in ripe pericarp of Liberty may account for the reduction of climacteric ethylene production, and prolonged storage life.

  10. SYNTHESIS OF NiO NANOPARTICLES IN ETHYLENE GLYCOL

    Institute of Scientific and Technical Information of China (English)

    Desheng Ai; Xiaming Dai; Qingfeng Li; Changsheng Deng; Shinhoo Kang

    2004-01-01

    NiO nanoparticles with well-dispersed property were prepared via a wet chemical method in ethylene glycol (EG) without soluble polymer as a protective agent. The mechanism of chemical process was proposed based on color change during the experiment. The dispersion function of EG was discussed.

  11. Proteomic Responses in Arabidopsis thaliana Seedlings Treated with Ethylene

    Science.gov (United States)

    Ethylene (ET) is a volatile plant growth hormone that most famously modulates fruit ripening, but it also controls plant growth, development and stress responses. In Arabidopsis thaliana, ET is perceived by receptors in the endoplasmic reticulum, and a signal is transduced through a protein kinase,...

  12. Direct Routes from Synthesis Gas to Ethylene Glycol.

    Science.gov (United States)

    Dombek, B. D.

    1986-01-01

    Discusses the synthesis of ethylene glycol from carbon monoxide and hydrogen using bimetallic catalysts. Although this technology has not been implemented, it illustrates two important future trends, namely, use of bimetallic catalysts and use of coal-derived carbon monoxide and hydrogen as a new feed stock. (JN)

  13. IRIS Toxicological Review of Ethylene Glycol Mono Butyl ...

    Science.gov (United States)

    EPA has finalized the Toxicological Review of Ethylene Glycol Mono Butyl Ether: in support of the Integrated Risk Information System (IRIS). Now final, this assessment may be used by EPA’s program and regional offices to inform decisions to protect human health. N/A

  14. Challenges in the diagnosis of ethylene glycol poisoning.

    Science.gov (United States)

    McQuade, David J; Dargan, Paul I; Wood, David M

    2014-03-01

    Ethylene glycol poisoning, while uncommon, is clinically significant due to the associated risk of severe morbidity or lethality and it continues to occur in many countries around the world. The clinical presentation of ethylene glycol toxicity, while classically described in three phases, varies widely and when combined with the range of differential diagnoses that must be considered makes diagnosis challenging. Early and accurate detection is important in these patients, however, as there is a need to start antidotal treatment early to prevent serious harm. In this article, we will review the literature and provide guidance regarding the diagnosis of ethylene glycol poisoning. While gas chromatography is the gold standard, the usefulness of this test is hampered by delays in access due to availability. Consequently, there are several surrogate markers that can give an indication of ethylene glycol exposure but these must be interpreted with caution and within the clinical context. An in-depth review of these tests, particularly the detection of a raised osmolar gap or an raised anion gap acidosis, will form the main focus of this article.

  15. Ethylene glycol emissions from on-road vehicles.

    Science.gov (United States)

    Wood, Ezra C; Knighton, W Berk; Fortner, Ed C; Herndon, Scott C; Onasch, Timothy B; Franklin, Jonathan P; Worsnop, Douglas R; Dallmann, Timothy R; Gentner, Drew R; Goldstein, Allen H; Harley, Robert A

    2015-03-17

    Ethylene glycol (HOCH2CH2OH), used as engine coolant for most on-road vehicles, is an intermediate volatility organic compound (IVOC) with a high Henry's law coefficient. We present measurements of ethylene glycol (EG) vapor in the Caldecott Tunnel near San Francisco, using a proton transfer reaction mass spectrometer (PTR-MS). Ethylene glycol was detected at mass-to-charge ratio 45, usually interpreted as solely coming from acetaldehyde. EG concentrations in bore 1 of the Caldecott Tunnel, which has a 4% uphill grade, were characterized by infrequent (approximately once per day) events with concentrations exceeding 10 times the average concentration, likely from vehicles with malfunctioning engine coolant systems. Limited measurements in tunnels near Houston and Boston are not conclusive regarding the presence of EG in sampled air. Previous PTR-MS measurements in urban areas may have overestimated acetaldehyde concentrations at times due to this interference by ethylene glycol. Estimates of EG emission rates from the Caldecott Tunnel data are unrealistically high, suggesting that the Caldecott data are not representative of emissions on a national or global scale. EG emissions are potentially important because they can lead to the formation of secondary organic aerosol following oxidation in the atmospheric aqueous phase.

  16. Glycolic acid production using ethylene glycol-oxidizing microorganisms.

    Science.gov (United States)

    Kataoka, M; Sasaki, M; Hidalgo, A R; Nakano, M; Shimizu, S

    2001-10-01

    Screening for microorganisms oxidizing ethylene glycol to glycolic acid was carried out. Among stock cultures, several yeasts and acetic acid bacteria showed high glycolic acid producing activity. Pichia naganishii AKU 4267 formed the highest concentration of glycolic acid, 35.3 g/l, from 10% (v/v) ethylene glycol (molar conversion yield, 26.0%). Among soil isolates, Rhodotorula sp. 3Pr-126, isolated using propylene glycol as a sole carbon source, formed the highest concentration of glycolic acid, 25.1 g/l, from 10% (v/v) ethylene glycol (molar conversion yield, 18.5%). Rhodotorula sp. 3Pr-126 showed higher activity toward 20% (v/v) ethylene glycol than P. naganishii AKU 4267. Optimization of the conditions for glycolic acid production was investigated using P. naganishii AKU 4267 and Rhodotorula sp. 3Pr-126. Under the optimized conditions, P. naganishii AKU 4267 and Rhodotorula sp. 3Pr-126 formed 105 and 110 g/l of glycolic acid (corrected molar conversion yields, 88.0 and 92.2%) during 120 h of reaction, respectively.

  17. RTE1, A Novel Regulator of Ethylene Receptor Function

    Energy Technology Data Exchange (ETDEWEB)

    Caren Chang (PI)

    2013-02-05

    RTE1 is a novel conserved gene found in both plants and animals. The main aims of this project were to: 1) examine Arabidopsis RTE1 function using genetic and cell biological analyses, and 2) determine whether the Arabidopsis RTH gene plays a role similar to that of RTE1 in ethylene signaling.

  18. Development of new photocatalysts for efficient removal of ethylene

    DEFF Research Database (Denmark)

    Nielsen, Morten Godtfred

    The aim of this thesis has been to remove ethylene/ethene (from here on called ethene because it is shortest) photocatalytically with the primary purpose of preventing fruit ripening during shipping. This has been achieved based on TiO2. The topic has been approached from different angles. The most...

  19. Flower development, reproduction and fruit ripening : the role of ethylene

    NARCIS (Netherlands)

    Martinis, Domenico de

    2006-01-01

    This thesis approaches the study of the role of ethylene in different aspects of plant reproduction; flower development, pollination, fruit ripening and spoilage. These different aspects have been studied at physiological, biochemical and molecular level. Chapter I, general introduction is divided i

  20. Optical properties, ethylene production and softening in mango fruits

    NARCIS (Netherlands)

    Eccher Zerbini, P.C.; Vanoli, M.; Rizzolo, A.; Grassi, M.; Meirelles de Azevedo Pementel, A.; Spinelli, L.; Torricelli, A.

    2015-01-01

    Firmness decay, chlorophyll breakdown and carotenoid accumulation, controlled by ethylene, are major ripening events in mango fruit. Pigment content and tissue structure affect the optical properties of the mesocarp, which can be measured nondestructively in the intact fruit by time-resolved reflect

  1. Direct Routes from Synthesis Gas to Ethylene Glycol.

    Science.gov (United States)

    Dombek, B. D.

    1986-01-01

    Discusses the synthesis of ethylene glycol from carbon monoxide and hydrogen using bimetallic catalysts. Although this technology has not been implemented, it illustrates two important future trends, namely, use of bimetallic catalysts and use of coal-derived carbon monoxide and hydrogen as a new feed stock. (JN)

  2. Inhibition of auxin-induced ethylene production by lycoricidinol

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Bin-G.; Lee, June-S.; Oh, Seung-Eun (Yonsei Univ., Seoul (Republic of Korea)); Horiuchi, Yuko; Imaseki, Hidemasa

    1984-03-01

    Lycoricidinol, a natural growth inhibitor isolated from bulbs of Lycoris radiata Herb. strongly suppressed auxin-induced ethylene production from the hypocotyl segments of etiolated mung bean (Vigna radiata Wilczek) seedlings. The inhibitor did not significantly inhibit ethylene formation from its immediate precursor, 1-aminocyclopropane-1-carboxylic acid (ACC), during short-term (up to 4h) incubation. The ACC content in tissue treated with IAA was reduced by lycoricidinol in close parallel with the inhibition of ethylene production. Examination of radioactive metabolites in tissues labeled with 3,4-/sup 14/C-methionine indicated that reduction of the ACC content was not due to any possible promotive effect of lycoricidinol on conjugation of ACC with malonate. Lycoricidinol showed no inhibitory effect on the activity of ACC synthase if applied in vitro, but it almost completely abolished the increase in the enzyme activity when applied in vivo during incubation of the tissue with IAA. Lycoricidinol also strongly inhibited incorporation of /sup 14/C-leucine into protein in the tissue. The suppression of the enzyme induction and, in turn, that of ethylene production by lycoricidinol were interpreted as being due to the inhibition of protein synthesis.

  3. Flower development, reproduction and fruit ripening : the role of ethylene

    NARCIS (Netherlands)

    Martinis, Domenico de

    2006-01-01

    This thesis approaches the study of the role of ethylene in different aspects of plant reproduction; flower development, pollination, fruit ripening and spoilage. These different aspects have been studied at physiological, biochemical and molecular level. Chapter I, general introduction is divided i

  4. Role of ethylene in the germination metabolism of ricinus communis

    Science.gov (United States)

    Cristescu, Simona; Dumitras, Dan C.; Godeanu, Adriana

    1999-03-01

    A CO2 laser-based photoacoustic method has been used to monitor the ethylene (C2H4) released by castor bean (Ricinus communis) seeds during germination. The relationship between the evolution of the C2H4 germinating seeds and the respiration intensity is presented.

  5. Ethylene Glycol Metabolism in the Acetogen Acetobacterium woodii.

    Science.gov (United States)

    Trifunović, Dragan; Schuchmann, Kai; Müller, Volker

    2016-01-19

    The acetogenic bacterium Acetobacterium woodii is able to grow by the oxidation of diols, such as 1,2-propanediol, 2,3-butanediol, or ethylene glycol. Recent analyses demonstrated fundamentally different ways for oxidation of 1,2-propanediol and 2,3-butanediol. Here, we analyzed the metabolism of ethylene glycol. Our data demonstrate that ethylene glycol is dehydrated to acetaldehyde, which is then disproportionated to ethanol and acetyl coenzyme A (acetyl-CoA). The latter is further converted to acetate, and this pathway is coupled to ATP formation by substrate-level phosphorylation. Apparently, the product ethanol is in part further oxidized and the reducing equivalents are recycled by reduction of CO2 to acetate in the Wood-Ljungdahl pathway. Biochemical data as well as the results of protein synthesis analysis are consistent with the hypothesis that the propane diol dehydratase (PduCDE) and CoA-dependent propionaldehyde dehydrogenase (PduP) proteins, encoded by the pdu gene cluster, also catalyze ethylene glycol dehydration to acetaldehyde and its CoA-dependent oxidation to acetyl-CoA. Moreover, genes encoding bacterial microcompartments as part of the pdu gene cluster are also expressed during growth on ethylene glycol, arguing for a dual function of the Pdu microcompartment system. Acetogenic bacteria are characterized by their ability to use CO2 as a terminal electron acceptor by a specific pathway, the Wood-Ljungdahl pathway, enabling in most acetogens chemolithoautotrophic growth with H2 and CO2. However, acetogens are very versatile and can use a wide variety of different substrates for growth. Here we report on the elucidation of the pathway for utilization of ethylene glycol by the model acetogen Acetobacterium woodii. This diol is degraded by dehydration to acetaldehyde followed by a disproportionation to acetate and ethanol. We present evidence that this pathway is catalyzed by the same enzyme system recently described for the utilization of 1

  6. Ethylene oxidation chemistry in a well-stirred reactor

    Energy Technology Data Exchange (ETDEWEB)

    Marinov, N. [Lawrence Livermore National Lab., CA (United States); Malte, P. [Univ. of Washington, Seattle, WA (United States). Dept. of Mechanical Engineering

    1994-09-01

    Ethylene is an important intermediate in the combustion of methane, larger aliphatic hydrocarbons, and aromatics. Detailed fuel-lean C{sub 2}H{sub 4}H{sub 2}O/air well-stirred reactor data by Thornton were used to analyze reported combustion chemistry mechanisms and the development of this study`s ethylene oxidation mechanism. The data set had been obtained for the temperature range 1,003 to 1,253 K and ethylene-oxygen equivalence ratio range 0.086 to 0.103, at atmospheric pressure. Mechanisms were derived from reaction sets of Westbrook and Pitz, and Dagaut, Cathonnet and Boettner. Examination of each reported mechanism indicated unusually large kinetic rates for the vinyl decomposition reaction were used in order to obtain agreement with the Thornton data set. An ethylene oxidation model was developed in order to address the mechanistic problems of the previous models. This study`s mechanism well simulated the overall rate of ethylene oxidation and concentration profiles of CO, CO{sub 2}, H{sub 2}, CH{sub 2}O, C{sub 2}H{sub 2}, CH{sub 3}OH, CH{sub 4}, and C{sub 2}H{sub 6}. Successful predictions by the model were dependent on a new high temperature vinyl oxidation reaction route, C{sub 2}H{sub 3} + O{sub 2} = CH{sub 2}CHO + O with a branching ratio of 1.19--1.21 at 1,053 K to 1.63--2.47 at 1,253 K. The branching ratio values were dependent upon the extent of fall-off for the C{sub 2}H{sub 3} + O{sub 2} = CH{sub 2}O + HCO reaction. 132 refs.

  7. The Effect of Ethylene and Propylene Pulses on Respiration, Ripening Advancement, Ethylene-Forming Enzyme, and 1-Aminocyclopropane-1-carboxylic Acid Synthase Activity in Avocado Fruit.

    Science.gov (United States)

    Starrett, D A; Laties, G G

    1991-03-01

    When early-season avocado fruit (Persea americana Mill. cv Hass) were treated with ethylene or propylene for 24 hours immediately on picking, the time to the onset of the respiratory climacteric, i.e. the lag period, remained unchanged compared with that in untreated fruit. When fruit were pulsed 24 hours after picking, on the other hand, the lag period was shortened. In both cases, however, a 24 hour ethylene or propylene pulse induced a transient increase in respiration, called the pulse-peak, unaccompanied by ethylene production (IL Eaks [1980] Am Soc Hortic Sci 105: 744-747). The pulse also caused a sharp rise in ethylene-forming enzyme activity in both cases, without any increase in the low level of 1-aminocyclopropane-1-carboxylic acid synthase activity. Thus, the shortening of the lag period by an ethylene pulse is not due to an effect of ethylene on either of the two key enzymes in ethylene biosynthesis. A comparison of two-dimensional polyacrylamide gel electrophoresis polypeptide profiles of in vitro translation products of poly(A(+)) mRNA from control and ethylene-pulsed fruit showed both up- and down-regulation in response to ethylene pulsing of a number of genes expressed during the ripening syndrome. It is proposed that the pulse-peak or its underlying events reflect an intrinsic element in the ripening process that in late-season or continuously ethylene-treated fruit may be subsumed in the overall climacteric response. A computerized system that allows continuous readout of multiple samples has established that the continued presentation of exogeneous ethylene or propylene to preclimacteric fruit elicits a dual respiration response comprising the merged pulse-peak and climacteric peak in series. The sequential removal of cores from a single fruit has proven an unsatisfactory sampling procedure inasmuch as coring induces wound ethylene, evokes a positive respiration response, and advances ripening.

  8. Modulation of ethylene responses by OsRTH1 overexpression reveals the biological significance of ethylene in rice seedling growth and development.

    Science.gov (United States)

    Zhang, Wei; Zhou, Xin; Wen, Chi-Kuang

    2012-06-01

    Overexpression of Arabidopsis Reversion-To-ethylene Sensitivity1 (RTE1) results in whole-plant ethylene insensitivity dependent on the ethylene receptor gene Ethylene Response1 (ETR1). However, overexpression of the tomato RTE1 homologue Green Ripe (GR) delays fruit ripening but does not confer whole-plant ethylene insensitivity. It was decided to investigate whether aspects of ethylene-induced growth and development of the monocotyledonous model plant rice could be modulated by rice RTE1 homologues (OsRTH genes). Results from a cross-species complementation test in Arabidopsis showed that OsRTH1 overexpression complemented the rte1-2 loss-of-function mutation and conferred whole-plant ethylene insensitivity in an ETR1-dependent manner. In contrast, OsRTH2 and OsRTH3 overexpression did not complement rte1-2 or confer ethylene insensitivity. In rice, OsRTH1 overexpression substantially prevented ethylene-induced alterations in growth and development, including leaf senescence, seedling leaf elongation and development, coleoptile elongation or curvature, and adventitious root development. Results of subcellular localizations of OsRTHs, each fused with the green fluorescent protein, in onion epidermal cells suggested that the three OsRTHs were predominantly localized to the Golgi. OsRTH1 may be an RTE1 orthologue of rice and modulate rice ethylene responses. The possible roles of auxins and gibberellins in the ethylene-induced alterations in growth were evaluated and the biological significance of ethylene in the early stage of rice seedling growth is discussed.

  9. Laser transmission welding of poly(ethylene terephthalate) and biodegradable poly(ethylene terephthalate) - Based blends

    Science.gov (United States)

    Gisario, Annamaria; Veniali, Francesco; Barletta, Massimiliano; Tagliaferri, Vincenzo; Vesco, Silvia

    2017-03-01

    Joining of Poly(Ethylene Terephthalate) PET and its biodegradable derivatives is of high relevance to ensure good productive rate, low cost and operational safety for fabrication of medical and electronic devices, sport equipments as well as for manufacturing of food and drug packaging solutions. In the present investigation, granules of PET and PETs modified by organic additives, which promote biodegradation of the polymeric chains, were prepared by extrusion compounding. The achieved granules were subsequently re-extruded to shape thin (330 μm) flat sheets. Substrates cut from these sheets were joined by Laser Transmission Welding (LTW) with a continuous wave High Power Diode Laser (cw-HPDL). First, based on a qualitative evaluation of the welded joints, the most suitable operational windows for PETs laser joining were identified. Second, characterization of the mechanical properties of the welded joints was performed by tensile tests. Accordingly, Young's modulus of PET and biodegradable PET blends was studied by Takayanagi's model and, based on the experimental results, a novel predicting analytical model derived from the mixture rule was developed. Lastly, material degradation of the polymeric joints was evaluated by FT-IR analysis, thus allowing to identify the main routes to thermal degradation of PET and, especially, of biodegradable PET blends during laser processing.

  10. in situ ring-opening polymerization of hydroxyapatite/poly(ethylene adipate)--(ethylene terephthalate) biomimetic composites

    Indian Academy of Sciences (India)

    Punnama Siriphannon; Pathavuth Monvisade

    2013-02-01

    Hydroxyapatite/poly(ethylene adipate)--poly(ethylene terephthalate) biomaterials (HAp/PEA--PET) have been prepared by ring opening polymerization (ROP) of cyclic oligo(ethylene adipate)--oligo(ethylene terephthalate) (C-OEA--C-OET) in the porous hydroxyapatite (HAp) scaffolds at 250 °C for 24 h under vacuum. The content of ROP-PEA--PET in the HAp/PEA--PET composite was about 20 wt% with the values of number average molecular weight ($\\bar{M}$n) and weight average molecular weight ($\\bar{M}$W) of 3380 and 7160 g/mol, respectively. Compressive strength and modulus of the HAp/PEA--PET composites were about 29 and 246 MPa, respectively. These mechanical properties were higher than those of the porous HAp templates and natural cancellous bone. In vitro bioactivity of the HAp/PEA--PET composites was studied by soaking in simulated body fluid (SBF) under the flowing system at the rate of 130 mL/day for 7, 14, 21 and 28 days. The formation of hydroxyapatite nanocrystals was observed on the composite surfaces through the consumption of calcium and phosphorus from the SBF solution, indicating the bioactivity of these HAp/PEA--PET composites. These results indicated the competency of HAp/PEA--PET composites for biomedical applications.

  11. Ethylene adsorption on regularly stepped copper surface: C 2H 4 on Cu(210)

    Science.gov (United States)

    Yamazaki, Daichi; Okada, Michio; Franco, Francisco C., Jr.; Kasai, Toshio

    2011-05-01

    Ethylene adsorption on regularly stepped Cu(210) surface was investigated with infrared reflection-adsorption spectroscopy and temperature programmed desorption. At 90 K, π-bonded ethylene was adsorbed on Cu(210) molecularly and all species were desorbed below 160 K. There were three types of π-bonded ethylene on the surface. Recent experimental studies have suggested that ethylene is dehydrogenated on Cu(410) due to the regular step [Kravchuk et al ., J. Phys. Chem. C, 113 (2009) 20881]. However, neither the formation of di-σ-bonded ethylene nor dehydrogenation occurred on Cu(210).

  12. Polyamines inhibit biosynthesis of ethylene in higher plant tissue and fruit protoplasts.

    Science.gov (United States)

    Apelbaum, A; Burgoon, A C; Anderson, J D; Lieberman, M

    1981-08-01

    Ethylene production in apple fruit and protoplasts and in leaf tissue was inhibited by spermidine or spermine. These polyamines, as well as putrescine, inhibited auxin-induced ethylene production and the conversion of methionine and 1-aminocyclopropane-1-carboxylic acid to ethylene. Polyamines were more effective as inhibitors of ethylene synthesis at the early, rather than at the late, stages of fruit ripening. Ca(2+) in the incubation medium reduced the inhibitory effect caused by the amines. A possible mode of action by which polyamines inhibit ethylene production is discussed.

  13. A genome-wide screen for ethylene-induced ethylene response factors (ERFs) in hybrid aspen stem identifies ERF genes that modify stem growth and wood properties.

    Science.gov (United States)

    Vahala, Jorma; Felten, Judith; Love, Jonathan; Gorzsás, András; Gerber, Lorenz; Lamminmäki, Airi; Kangasjärvi, Jaakko; Sundberg, Björn

    2013-10-01

    Ethylene Response Factors (ERFs) are a large family of transcription factors that mediate responses to ethylene. Ethylene affects many aspects of wood development and is involved in tension wood formation. Thus ERFs could be key players connecting ethylene action to wood development. We identified 170 gene models encoding ERFs in the Populus trichocarpa genome. The transcriptional responses of ERF genes to ethylene treatments were determined in stem tissues of hybrid aspen (Populus tremula × tremuloides) by qPCR. Selected ethylene-responsive ERFs were overexpressed in wood-forming tissues and characterized for growth and wood chemotypes by FT-IR. Fifty ERFs in Populus showed more than five-fold increased transcript accumulation in response to ethylene treatments. Twenty-six ERFs were selected for further analyses. A majority of these were induced during tension wood formation. Overexpression of ERFs 18, 21, 30, 85 and 139 in wood-forming tissues of hybrid aspen modified the wood chemotype. Moreover, overexpression of ERF139 caused a dwarf-phenotype with altered wood development, and overexpression of ERF18, 34 and 35 slightly increased stem diameter. We identified ethylene-induced ERFs that respond to tension wood formation, and modify wood formation when overexpressed. This provides support for their role in ethylene-mediated regulation of wood development.

  14. Thermal decomposition of ethylene oxide on Pd(111). Comparison of the pathways for the selective oxidation of ethylene and olefin metathesis

    Energy Technology Data Exchange (ETDEWEB)

    Lambert, R.M. (Univ. of Cambridge (United Kingdom)); Ormerod, R.M. (Univ. of Keele (United Kingdom)); Tysoe, W.T. (Univ. of Wisconsin, Milwaukee, WI (United States))

    1994-03-01

    The product distribution detected in the multimass temperature-programmed desorption of a saturated overlayer of ethylene oxide adsorbed on Pd(111) at [approximately] 180 K indicates that it decomposes to yield ethylene and acetaldehyde. These observations are interpreted by postulating that ethylene oxide reacts to form an oxymetallocycle. This is proposed to thermally decompose in a manner analogous to carbometallocycles that form during olefin metathesis catalysis by the reaction between an alkene and a surface carbene. Thus, the metallocycle can decompose to yield ethylene and deposit adsorbed atomic oxygen or undergo a [beta]-hydrogen transfer to form acetaldehyde. 25 refs., 2 figs., 1 tab.

  15. Links Between Ethylene and Sulfur Nutrition-A Regulatory Interplay or Just Metabolite Association?

    Science.gov (United States)

    Wawrzynska, Anna; Moniuszko, Grzegorz; Sirko, Agnieszka

    2015-01-01

    Multiple reports demonstrate associations between ethylene and sulfur metabolisms, however the details of these links have not yet been fully characterized; the links might be at the metabolic and the regulatory levels. First, sulfur-containing metabolite, methionine, is a precursor of ethylene and is a rate limiting metabolite for ethylene synthesis; the methionine cycle contributes to both sulfur and ethylene metabolism. On the other hand, ethylene is involved in the complex response networks to various stresses and it is known that S deficiency leads to photosynthesis and C metabolism disturbances that might be responsible for oxidative stress. In several plant species, ethylene increases during sulfur starvation and might serve signaling purposes to initiate the process of metabolism reprogramming during adjustment to sulfur deficit. An elevated level of ethylene might result from increased activity of enzymes involved in its synthesis. It has been demonstrated that the alleviation of cadmium stress in plants by application of S seems to be mediated by ethylene formation. On the other hand, the ethylene-insensitive Nicotiana attenuata plants are impaired in sulfur uptake, reduction and metabolism, and they invest their already limited S into methionine needed for synthesis of ethylene constitutively emitted in large amounts to the atmosphere. Regulatory links of EIN3 and SLIM1 (both from the same family of transcriptional factors) involved in the regulation of ethylene and sulfur pathway, respectively, is also quite probable as well as the reciprocal modulation of both pathways on the enzyme activity levels.

  16. Links Between Ethylene and Sulfur Nutrition—A Regulatory Interplay or Just Metabolite Association?

    Science.gov (United States)

    Wawrzynska, Anna; Moniuszko, Grzegorz; Sirko, Agnieszka

    2015-01-01

    Multiple reports demonstrate associations between ethylene and sulfur metabolisms, however the details of these links have not yet been fully characterized; the links might be at the metabolic and the regulatory levels. First, sulfur-containing metabolite, methionine, is a precursor of ethylene and is a rate limiting metabolite for ethylene synthesis; the methionine cycle contributes to both sulfur and ethylene metabolism. On the other hand, ethylene is involved in the complex response networks to various stresses and it is known that S deficiency leads to photosynthesis and C metabolism disturbances that might be responsible for oxidative stress. In several plant species, ethylene increases during sulfur starvation and might serve signaling purposes to initiate the process of metabolism reprogramming during adjustment to sulfur deficit. An elevated level of ethylene might result from increased activity of enzymes involved in its synthesis. It has been demonstrated that the alleviation of cadmium stress in plants by application of S seems to be mediated by ethylene formation. On the other hand, the ethylene-insensitive Nicotiana attenuata plants are impaired in sulfur uptake, reduction and metabolism, and they invest their already limited S into methionine needed for synthesis of ethylene constitutively emitted in large amounts to the atmosphere. Regulatory links of EIN3 and SLIM1 (both from the same family of transcriptional factors) involved in the regulation of ethylene and sulfur pathway, respectively, is also quite probable as well as the reciprocal modulation of both pathways on the enzyme activity levels. PMID:26648954

  17. Ethylene Production and Petiole Growth in Rumex Plants Induced by Soil Waterlogging

    Science.gov (United States)

    Voesenek, Laurentius A. C. J.; Harren, Frans J. M.; Bögemann, Gerald M.; Blom, Cornelius W. P. M.; Reuss, Jörg

    1990-01-01

    Petiole growth of Rumex acetosa L., Rumex crispus L., and Rumex palustris Sm. in response to soil waterlogging was studied in relation to production of the gaseous plant hormone ethylene. Ethylene production was monitored in a flow-through system and a recently developed laser driven photoacoustic detection system, which allowed ethylene measurements as low as 6 picoliters per liter. R. acetosa showed a two-fold increase in ethylene production correlated with a slight enhancement of the growth of the petiole that developed during the waterlogging treatment. Both R. crispus and R. palustris showed a strong petiole elongation of existing as well as newly formed petioles, which was correlated with a 20-fold increase in ethylene production after approximately 7 days. Increased rates of ethylene production in R. palustris were related to a strong increase in 1-aminocyclopropane-1-carboxylic acid (ACC) concentration and a slight, but detectable, increase in ethylene forming enzyme activity. In R. acetosa on the other hand, only a very small increase in ACC concentration was observed. Changes in ethylene production in Rumex are strongly correlated with variation in ACC content and ethylene forming enzyme activity. The interaction between ethylene production/internal concentration and ethylene sensitivity of the three Rumex species is discussed in relation to their field location in a flooding gradient and their differential resistance toward waterlogging and submergence. PMID:16667798

  18. Sites of ethylene production in the pollinated and unpollinated senescing carnation (Dianthus caryophyllus) inflorescence.

    Science.gov (United States)

    Nichols, R

    1977-01-01

    Production of endogenous ethylene from the styles, ovary and petals of pollinated and unpollinated flowers of Dianthus caryophyllus L. was measured. The rate of ethylene production of cut, unpollinated flowers aged in water at 18°C was low until the onset of petal wilting, when a rapid surge of ethylene occurred in all tissues. The flower ethylene production was evolved mostly from the styles and petals. The bases of petals from unpollinated, senescing flowers evolved ethylene faster and sometimes earlier than the upper parts. Treatment of cut flowers with propylene, an ethylene analogue, accelerated wilting of flower petals and promoted endogenous ethylene production in all flower tissues. Pollination of intact flowers also promoted endogenous ethylene production and caused accelerated petal wilting within 2-3 days from pollination. Although the data are consistent with the hypothesis that ethylene forms a link between pollination of the style and petal wilting, in the unpollinated flower the style and petals can evolve a surge of ethylene independently of each other, about the time when the petals irreversibly wilt. The results are discussed in relation to the role of ethylene in flower senescence.

  19. Dehydration and dehydrogenation of ethylene glycol on rutile TiO2(110).

    Science.gov (United States)

    Li, Zhenjun; Kay, Bruce D; Dohnálek, Zdenek

    2013-08-07

    The interactions of ethylene glycol with a partially reduced rutile TiO2(110) surface have been studied using temperature programmed desorption (TPD). The saturation coverage on surface Ti rows is determined to be 0.43 monolayer (ML), slightly less than one ethylene glycol per two Ti sites. Most of the adsorbed ethylene glycol (∼80%) undergoes further reactions to yield other products. Two major channels are observed, dehydration yielding ethylene and water and dehydrogenation yielding acetaldehyde and hydrogen. Hydrogen formation is rather surprising as it has not been observed previously on TiO2(110) from simple organic molecules. The coverage dependent yields of ethylene and acetaldehyde correlate well with those of water and hydrogen, respectively. Dehydration dominates at lower ethylene glycol coverages (ethylene glycol coverages (>0.2 ML). Our results suggest that the observed dehydration and dehydrogenation reactions proceed via different surface intermediates.

  20. Effect of the potassium permanganate during papaya fruit ripening: Ethylene production

    Science.gov (United States)

    Corrêa, S. F.; Filho, M. B.; da Silva, M. G.; Oliveira, J. G.; Aroucha, E. M. M.; Silva, R. F.; Pereira, M. G.; Vargas, H.

    2005-06-01

    The effect of potassium permanganate (KMnO4) on the ripening process of papaya fruits by monitoring the ethylene emission rates is reported. The ethylene emission was monitored by a photoacoustic spectrometer. Two experimental conditions were applied, being one of them just putting the fruit alone inside the sampling chamber and the second, modifying the atmosphere by the presence of KMnO4. The use of the ethylene absorber reduces the autocatalytic process of ethylene during papaya fruit ripening. For 20 g of KMnO4 the maximal intensity of the ethylene emission decreases by a factor two. Using the same amount of KMnO4, a reduction of about 2.2% in the concentration of ethylene for a mixture of 1ppmv of ethylene in synthetic air was observed.

  1. Differential expression of ethylene biosynthesis genes in drupelets and receptacle of raspberry (Rubus idaeus).

    Science.gov (United States)

    Fuentes, Lida; Monsalve, Liliam; Morales-Quintana, Luis; Valdenegro, Mónika; Martínez, Juan-Pablo; Defilippi, Bruno G; González-Agüero, Mauricio

    2015-05-01

    Red Raspberry (Rubus idaeus) is traditionally classified as non-climacteric, and the role of ethylene in fruit ripening is not clear. The available information indicates that the receptacle, a modified stem that supports the drupelets, is involved in ethylene production of ripe fruits. In this study, we report receptacle-related ethylene biosynthesis during the ripening of fruits of cv. Heritage. In addition, the expression pattern of ethylene biosynthesis transcripts was evaluated during the ripening process. The major transcript levels of 1-aminocyclopropane-1-carboxylic acid synthase (RiACS1) and 1-aminocyclopropane-1-carboxylic acid oxidase (RiACO1) were concomitant with ethylene production, increased total soluble solids (TSS) and decreased titratable acidity (TA) and fruit firmness. Moreover, ethylene biosynthesis and transcript levels of RiACS1 and RiACO1 were higher in the receptacle, sustaining the receptacle's role as a source of ethylene in regulating the ripening of raspberry.

  2. Molecular cloning and functional analysis of an ethylene receptor gene from sugarcane (Saccharum spp.) by hormone and environmental stresses

    Science.gov (United States)

    Ethylene receptor (ethylene response sensor, ERS) is the primary component involving in the ethylene biosynthesis and ethylene signal transduction pathway. In the present study, a GZ-ERS gene encoding ERS was cloned from a sugarcane cv. YL17 (Saccharum spp.) using RT-PCR and ligation-mediated PCR wi...

  3. Measurement of ethylene emission from Japanese red pine (Pinus densiflora) under field conditions in NOx-polluted areas.

    Science.gov (United States)

    Kume, A; Tsuboi, N; Nakatani, N; Nakane, K; Sakurai, N; Nakagawa, N; Sakugawa, H

    2001-01-01

    Emission of ethylene from the needles of Japanese red pine, Pinus densiflora, was measured in air-polluted areas in Hiroshima, Japan. We applied a suitable protocol to determine the rate of ethylene emission from the excised needles. The influence of excision of needles on ethylene emission was not detected during the first 4 h of incubation at 20 degrees C. Ethylene emissions were low in the unpolluted (clean) areas regardless of the altitude or season. The emission of stress ethylene increased with the atmospheric NO2 concentration, suggesting that atmospheric NOx or related substances induced the higher ethylene emission in the polluted areas (near urban and industrial areas). In all cases, 1-year-old needles emitted significantly larger amounts of ethylene than the current needles. Ethylene emission did not increase evenly in the polluted areas, but the frequency of trees emitting high ethylene increased. Therefore, threshold rates for the baseline ethylene emission were proposed.

  4. Hyperbranched PEG by random copolymerization of ethylene oxide and glycidol.

    Science.gov (United States)

    Wilms, Daniel; Schömer, Martina; Wurm, Frederik; Hermanns, M Iris; Kirkpatrick, C James; Frey, Holger

    2010-10-18

    The synthesis of hyperbranched poly(ethylene glycol) (hbPEG) in one step was realized by random copolymerization of ethylene oxide and glycidol, leading to a biocompatible, amorphous material with multiple hydroxyl functionalities. A series of copolymers with moderate polydispersity ($\\overline {M} _{{\\rm w}} /\\overline {M} _{{\\rm n}} $ < 1.8) was obtained with varying glycidol content (3-40 mol-%) and molecular weights up to 49 800 g mol(-1) . The randomly branched structure of the copolymers was confirmed by (1) H and (13) C NMR spectroscopy and thermal analysis (differential scanning calorimetry). MTS assay demonstrated low cell toxicity of the hyperbranched PEG, comparable to the highly established linear PEG.

  5. Ethylene, nitric oxide and haemoglobins in plant tolerance to flooding

    DEFF Research Database (Denmark)

    Mur, Luis A J; Gupta, Kapuganti J; Hebelstrup, Kim

    2015-01-01

    As much as 12% of the world's soils may suffer excess water so that flooding is a major limiting factor on crop production in many areas. Plants attempt to deal with submergence by forming root aerenchyma to facilitate oxygen diffusion from the shoot to the root, initiating a hyponastic response...... where petiole elongation facilitates access to atmospheric oxygen or initiating a bio-energetically conserving quiescence phase. Ethylene has well established roles in the initiation of programmed cell death (PCD) to form air-spaces in aerenchyma and in the hyponastic responses in petioles. The flooding......-tolerant species Rumex palustris and the model plant Arabidopsis thaliana have been extensively exploited to reveal some key molecular events. Our groups have recently demonstrated that nitric oxide (NO) triggers the biosynthesis of ethylene during stress and that NO plays key roles in PCD and the hyponastic...

  6. Conjugates of abscisic acid, brassinosteroids, ethylene, gibberellins, and jasmonates.

    Science.gov (United States)

    Piotrowska, Alicja; Bajguz, Andrzej

    2011-12-01

    Phytohormones, including auxins, abscisic acid, brassinosteroids, cytokinins, ethylene, gibberellins, and jasmonates, are involved in all aspects of plant growth, and developmental processes as well as environmental responses. However, our understanding of hormonal homeostasis is far from complete. Phytohormone conjugation is considered as a part of the mechanism to control cellular levels of these compounds. Active phytohormones are changed into multiple forms by acylation, esterification or glycosylation, for example. It seems that conjugated compounds could serve as pool of inactive phytohormones that can be converted to active forms by de-conjugation reactions. Some conjugates are thought to be temporary storage forms, from which free active hormones can be released after hydrolysis. It is also believed that conjugation serves functions, such as irreversible inactivation, transport, compartmentalization, and protection against degradation. The nature of abscisic acid, brassinosteroid, ethylene, gibberellin, and jasmonate conjugates is discussed.

  7. Epidemiological studies on ethylene oxide and cancer: an updating.

    Science.gov (United States)

    Hogstedt, L C

    1988-01-01

    In 1959, Dr Lars Ehrenberg and a coworker warned the Swedish authorities that ethylene oxide, a common chemical, constituted a potential cancer hazard. Twenty years later, the first epidemiological study and case reports were published indicating an increased cancer risk after occupational exposure to ethylene oxide. An updating of three small Swedish cohorts comprising 709 employees revealed 33 deaths from cancer whereas 20 were expected from national average rates. The excess was due mainly to an increased risk of stomach cancer in one production plant and an excess of blood and lymphatic malignancies in all three cohorts. The results are in accordance with the results of clastogenic, animal and short-term tests and support Professor Ehrenberg's hypothesis, formulated 28 years ago.

  8. Methanolysis of Poly(ethylene terephthalate) in Supercritical Phase

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The depolymerization of poly(ethylene terephthalate, PET) in supercritical methanol is studied using a stainless stirred autoclave at temperature of 255~260℃, pressure of 8.5~14.0 MPa, and methanol/PET weight ratio of 3~8. Under the optimal conditions, the PET is depolymerized completely to its monomers in 60 min. The main products of the reaction are dimethyl terephthalate and ethylene glycol. There are still some small amounts of byproducts, such as methyl-(2-hydroxyethyl) terephthalate, bis(hydroxyethyl) terephthalate, dimers and oligomers. Reversed-phase high performance liquid chrom- atography and gas chromatography are used to analyze solid products and liquid products respectively. The results of depolymerization show that the yield of dimethyl terephthalate and the degree of PET depolymerization are dependent on the reaction temperature, weight ratio of methanol to PET and reaction time. But the reaction pressure has little influence on the depolymerization as long as methanol is in supercritical state.

  9. A kinetic study of the electrochemical hydrogenation of ethylene

    Energy Technology Data Exchange (ETDEWEB)

    Sedighi, S. [Department of Chemical Engineering and Centre for Catalysis Research and Innovation, University of Ottawa, Ottawa, Ontario K1N 6N5 (Canada); Gardner, C.L., E-mail: cgardner88@sympatico.c [Department of Chemical Engineering and Centre for Catalysis Research and Innovation, University of Ottawa, Ottawa, Ontario K1N 6N5 (Canada)

    2010-02-01

    In this study, we have examined the kinetics of the electrochemical hydrogenation of ethylene in a PEM reactor. While in itself this reaction is of little industrial interest, this reaction can be looked upon as a model reaction for many of the important hydrogenation processes including the refining of heavy oils and the hydrogenation of vegetable oils. To study the electrochemical hydrogenation of ethylene, several experimental techniques have been used including polarization measurements, measurement of the composition of the exit gases and potential step, transient measurements. The results show that the hydrogenation reaction proceeds rapidly and essentially to completion. By fitting the experimental transient data to the results from a zero-dimensional mathematical model of the process, a set of kinetic parameters for the reactions has been obtained that give generally good agreement with the experimental results. It seems probable that similar experimental techniques could be used to study the electrochemical hydrogenation of other unsaturated organic molecules of more industrial significance.

  10. Polyamines in conventional and organic vegetables exposed to exogenous ethylene.

    Science.gov (United States)

    Rossetto, Maria Rosecler Miranda; Vianello, Fabio; Saeki, Margarida Juri; Lima, Giuseppina Pace Pereira

    2015-12-01

    Relationships between endogenous levels of polyamines by thin layer chromatography (TLC) and gas chromatography (GC), nitrate and response to the application of ethylene were established between organic and conventional vegetables (broccoli, collard greens, carrots and beets), both raw and cooked. Responses to ethylene showed that organic plants were less responsive to the growth regulator. The levels of free polyamines obtained by TLC were higher in organic vegetables. Organic broccoli showed higher levels of putrescine (Put), and cooking resulted in lowering the overall content of these amines. Conventional collard green showed the highest level of putrescine in the leaves compared with organic. Tubers of carrots and beets contain the highest levels of Put. These plants also contain high levels of spermine. GC analysis showed the highest polyamines contents compared with those obtained by TLC. Cooking process decreased putrescine and cadaverine content, both in conventionally and organically grown vegetables. Organic beets contain lower NO3(-) compared with its conventional counterpart.

  11. A bacterium that degrades and assimilates poly(ethylene terephthalate).

    Science.gov (United States)

    Yoshida, Shosuke; Hiraga, Kazumi; Takehana, Toshihiko; Taniguchi, Ikuo; Yamaji, Hironao; Maeda, Yasuhito; Toyohara, Kiyotsuna; Miyamoto, Kenji; Kimura, Yoshiharu; Oda, Kohei

    2016-03-11

    Poly(ethylene terephthalate) (PET) is used extensively worldwide in plastic products, and its accumulation in the environment has become a global concern. Because the ability to enzymatically degrade PET has been thought to be limited to a few fungal species, biodegradation is not yet a viable remediation or recycling strategy. By screening natural microbial communities exposed to PET in the environment, we isolated a novel bacterium, Ideonella sakaiensis 201-F6, that is able to use PET as its major energy and carbon source. When grown on PET, this strain produces two enzymes capable of hydrolyzing PET and the reaction intermediate, mono(2-hydroxyethyl) terephthalic acid. Both enzymes are required to enzymatically convert PET efficiently into its two environmentally benign monomers, terephthalic acid and ethylene glycol. Copyright © 2016, American Association for the Advancement of Science.

  12. Multimeric, Multifunctional Derivatives of Poly(ethylene glycol

    Directory of Open Access Journals (Sweden)

    Gian Maria Bonora

    2011-07-01

    Full Text Available This article reviews the use of multifunctional polymers founded on high-molecular weight poly(ethylene glycol (PEG. The design of new PEG derivatives assembled in a dendrimer-like multimeric fashion or bearing different functionalities on the same molecule is described. Their use as new drug delivery systems based on the conjugation of multiple copies or diversely active drugs on the same biocompatible support is illustrated.

  13. Fouling and Antifouling of Depetanizer in Ethylene Units

    Institute of Scientific and Technical Information of China (English)

    Dong Zhongjie; Li Yunlong; Fan Xuezhi; Hong Qingyao

    2002-01-01

    Factors affecting fouling of depentanizer in ethylene units wereexplored through study of thecomposition of pyrolysis gasoline, C5 distillate and fouling deposits from the depentanizer while takinginto consideration the processing parameters. A variety of antifouling measures, in particular the injec-tion of a special anti-fouling agent into the Cs gas phase pipeline and the C5 distillate reflux pipelinewere introduced. Commercial evaluation test of a multifunctional anti-fouling agent, the RIPP-1404anti-fouling agent, was also described.

  14. Removal of ethylene oxide from waste gases by absorption

    Directory of Open Access Journals (Sweden)

    Arsenijević Zorana Lj.

    2011-01-01

    Full Text Available Ethylene oxide (EtO is an organic compound, which is used as starting material in the production of polymers and as sterilizing agent for thermolabile materials. Although ethylene oxide is not common as an organic pollutant, its removal from numerous emission sources (e.g. ethylene oxide production plants or food and pharmaceutical sterilizing units is of the crucial importance because of its mutagenic, teratogenic and cancerogenic effect on human health. The objective of this paper is the experimental investigation of ethylene oxide (EtO absorption in diluted aqueous solution of sulfuric acid in order to evaluate the applicability of this procedure as well as to obtain project parameters for industrial plant realization. It was found that absorption is suitable as the fist step in the purification treatment of high EtO concentrations in the emission gases. According to the literature data, the basic parameter that defines the scrubber efficiency is the contact time, i.e. the ratio of packing height in scrubber and velocity of gas mixture. To investigate the characteristics of wet treatment in a broad range of contact time, part of experimental studies were conducted in the system with two and with three scrubbers in series. The obtained experimental results show that the high degree of EtO removal can be achieved (>98% when the contact time is sufficiently long (about 25 s. The process is effective until the concentration of formed glycol in the solution reaches value of about 20%. The process is safe and there is no danger of ignition and explosion of air and EtO mixture, although at the entrance to the scrubber EtO concentrations are significantly above the lower explosive limit.

  15. SURFACE TREATMENT OF POLY(ETHYLENE TEREPHTHALATE) FABRIC WITH POLYETHYLENEIMINE

    Institute of Scientific and Technical Information of China (English)

    O.J. ATEIZA; I. HOLME; J.E. McINTYRE

    1997-01-01

    A branched polyethyleneimine (BPEI) was applied to poly(ethylene terephthalate)(PET) fabric to improve its surface moisture absorption so that the fabric becomes less liable to retention of electrostatic charge. The durability of this treatment was assessed by washing and followed by measurement of charge development on the fabric. The treated samples showed improved surface wetting compared to the untreated. The results are consistent with attachment of the BPEI to the PET surface by a cross-linking mechanism.

  16. Ethylene oxidation in a well-stirred reactor

    Energy Technology Data Exchange (ETDEWEB)

    Marinov, N.M. [Lawrence Livermore National Lab., CA (United States); Malte, P.C. [Washington Univ., Seattle, WA (United States). Dept. of Mechanical Engineering

    1994-10-01

    The detailed ethylene oxidation data set of Thornton, obtained for a well-stirred reactor operated fuel-lean at atmospheric pressure and for temperatures of 1003K to 1253K, is used as a basis for the comparison of chemical kinetic mechanisms reported in the literature and for the development of a new ethylene oxidation mechanism. The mechanisms examined are those of Westbrook and Pitz and Dagaut et al. These mechanisms indicated that unusually large rates for the vinyl decomposition reaction are required to obtain agreement with the Thornton data set. A new ethylene oxidation mechanism is developed in order to overcome some of the drawbacks of the previous mechanisms. The new mechanism closely simulates the overall rate of loss of ethylene, and the concentation of CO, CO{sub 2}, H{sub 2}, CH{sub 2}O, C{sub 2}H{sub 2}, CH{sub 3}OH, CH{sub 4}, and C{sub 2}H{sub 6} measured for the stirred reactor. Predictions by this mechanism are dependent on a new high temperature vinyl oxidation route, C{sub 2}H{sub 3} + O{sub 2} = CH{sub 2}CHO + O with a k{sub C2H3+O2=CH2CHO+O}/k{sub C2H3+O2=CH2O+HCO} branching ratio of 1.20 at 1053K to 2.05 at 1253K. The branching ratio values were dependent upon the extent of fall-off for the C{sub 2}H{sub 3} + O{sub 2} = CH{sub 2}O + HCO reaction.

  17. Self-consistent-field analysis of the micellization of carboxy-modified poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) triblock copolymers

    NARCIS (Netherlands)

    Lauw, Y.; Leermakers, F.A.M.; Cohen Stuart, M.A.

    2006-01-01

    The micellization properties of carboxy-modified Pluronics P85 (poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (PEO-PPO-PEO) triblock copolymers) are investigated by means of a molecularly realistic self-consistent-field theory. We consider the, so-called, carboxylic acid

  18. Self-consistent-field analysis of the micellization of carboxy-modified poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) triblock copolymers

    NARCIS (Netherlands)

    Lauw, Y.; Leermakers, F.A.M.; Cohen Stuart, M.A.

    2006-01-01

    The micellization properties of carboxy-modified Pluronics P85 (poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) (PEO-PPO-PEO) triblock copolymers) are investigated by means of a molecularly realistic self-consistent-field theory. We consider the, so-called, carboxylic acid end-standi

  19. Ethylene and hydrogen peroxide are involved in brassinosteroid-induced salt tolerance in tomato

    Science.gov (United States)

    Zhu, Tong; Deng, Xingguang; Zhou, Xue; Zhu, Lisha; Zou, Lijuan; Li, Pengxu; Zhang, Dawei; Lin, Honghui

    2016-01-01

    Crosstalk between phytohormone pathways is essential in plant growth, development and stress responses. Brassinosteroids (BRs) and ethylene are both pivotal plant growth regulators, and the interaction between these two phytohormones in the tomato response to salt stress is still unclear. Here, we explored the mechanism by which BRs affect ethylene biosynthesis and signaling in tomato seedlings under salt stress. The activity of 1-aminocyclopropane-1-carboxylate synthase (ACS), an ethylene synthesis enzyme, and the ethylene signaling pathway were activated in plants pretreated with BRs. Scavenging of ethylene production or silencing of ethylene signaling components inhibited BR-induced salt tolerance and blocked BR-induced activities of several antioxidant enzymes. Previous studies have reported that BRs can induce plant tolerance to a variety of environmental stimuli by triggering the generation of H2O2 as a signaling molecule. We also found that H2O2 might be involved in the crosstalk between BRs and ethylene in the tomato response to salt stress. Simultaneously, BR-induced ethylene production was partially blocked by pretreated with a reactive oxygen species scavenger or synthesis inhibitor. These results strongly demonstrated that ethylene and H2O2 play important roles in BR-dependent induction of plant salt stress tolerance. Furthermore, we also investigated the relationship between BR signaling and ethylene signaling pathways in plant processes responding to salt stress. PMID:27739520

  20. Involvement of ethylene in sex expression and female flower development in watermelon (Citrullus lanatus).

    Science.gov (United States)

    Manzano, Susana; Martínez, Cecilia; García, Juan Manuel; Megías, Zoraida; Jamilena, Manuel

    2014-12-01

    Although it is known that ethylene has a masculinizing effect on watermelon, the specific role of this hormone in sex expression and flower development has not been analyzed in depth. By using different approaches the present work demonstrates that ethylene regulates differentially two sex-related developmental processes: sexual expression, i.e. the earliness and the number of female flowers per plant, and the development of individual floral buds. Ethylene production in the shoot apex as well as in male, female and bisexual flowers demonstrated that the female flower requires much more ethylene than the male one to develop, and that bisexual flowers result from a decrease in ethylene production in the female floral bud. The occurrence of bisexual flowers was found to be associated with elevated temperatures in the greenhouse, concomitantly with a reduction of ethylene production in the shoot apex. External treatments with ethephon and AVG, and the use of Cucurbita rootstocks with different ethylene production and sensitivity, confirmed that, as occurs in other cucurbit species, ethylene is required to arrest the development of stamens in the female flower. Nevertheless, in watermelon ethylene inhibits the transition from male to female flowering and reduces the number of pistillate flowers per plant, which runs contrary to findings in other cucurbit species. The use of Cucurbita rootstocks with elevated ethylene production delayed the production of female flowers but reduced the number of bisexual flowers, which is associated with a reduced fruit set and altered fruit shape.

  1. Interactions between ethylene, abscisic acid and cytokinin during germination and seedling establishment in Arabidopsis

    Indian Academy of Sciences (India)

    Veeraputhiran Subbiah; Karingu Janardhan Reddy

    2010-09-01

    In order to investigate the interaction of the plant hormones ethylene, abscisic acid (ABA) and cytokinin in seed germination and early seedling development, we studied germination in ethylene-related mutants of Arabidopsis. Mutations in the genes etr1 and ein2, which reduce ethylene responses, showed increased dormancy and a delay in germination in comparison with wild type. Mutations in etr1, ein2 and ein6 also resulted in increased sensitivity to ABA with respect to inhibition of germination. Conversely, mutations in ctr1 and eto3, which lead to an increased ethylene response and overproduction of ethylene, respectively, decreased sensitivity to ABA during germination. Increased ABA sensitivity was also effected in wild type seeds by the presence during germination of AgNO3, an inhibitor of ethylene action. The addition of the cytokinin N-6 benzyl adenine (BA) reversed the increased sensitivity of ethylene-resistant mutants to ABA. The action of cytokinin in reversing increased ABA sensitivity of ethylene-resistant mutants also suggests that at least part of the action of cytokinin in promoting germination is independent of its role in stimulating ethylene production. These observations further extend the evidence in support of interaction between ethylene, ABA and cytokinin signalling in controlling seed germination and early seedling development in Arabidopsis.

  2. Regulation of Senescence in Carnation (Dianthus caryophyllus) by Ethylene: Mode of Action.

    Science.gov (United States)

    Mayak, S; Vaadia, Y; Dilley, D R

    1977-04-01

    Carnation (Dianthus caryophyllus) flowers were exposed to 2 mul/l ethylene and examined at intervals to determine the time course of wilting, decrease in water uptake, and increase in ionic leakage in response to ethylene. A rapid decrease in water uptake was observed about 4 hours after initiating treatment with ethylene. This was followed by wilting (in-rolling of petals) about 2 hours later. Carbon dioxide inhibited the decline in water uptake and wilting and this is typical of most ethylene-induced responses. Ethylene did not affect closure of stomates. Ethylene enhanced ionic leakage, as measured by efflux of (36)Cl from the vacuole. This was judged to coincide with the decrease in water uptake. Gassing flowers with propylene initiated autocatalytic ethylene production within 2.4 hours. Since the increase in ethylene production by carnations preceded the increase in ionic leakage and the decline in water uptake by several hours, it is apparent that the change in ionic leakage does not lead to the initial increase in ethylene production as reported (Hanson and Kende 1975 Plant Physiol 55:663-669) in morning glory but may explain the autocatalytic phase of ethylene production.

  3. Differential expression of two novel members of the tomato ethylene-receptor family.

    Science.gov (United States)

    Tieman, D M; Klee, H J

    1999-05-01

    The phytohormone ethylene regulates many aspects of plant growth, development, and environmental responses. Much of the developmental regulation of ethylene responses in tomato (Lycopersicon esculentum) occurs at the level of hormone sensitivity. In an effort to understand the regulation of ethylene responses, we isolated and characterized tomato genes with sequence similarity to the Arabidopsis ETR1 (ethylene response 1) ethylene receptor. Previously, we isolated three genes that exhibit high similarity to ETR1 and to each other. Here we report the isolation of two additional genes, LeETR4 and LeETR5, that are only 42% and 40% identical to ETR1, respectively. Although the amino acids known to be involved in ethylene binding are conserved, LeETR5 lacks the histidine within the kinase domain that is predicted to be phosphorylated. This suggests that histidine kinase activity is not necessary for an ethylene response, because mutated forms of both LeETR4 and LeETR5 confer dominant ethylene insensitivity in transgenic Arabidopsis plants. Expression analysis indicates that LeETR4 accounts for most of the putative ethylene-receptor mRNA present in reproductive tissues, but, like LeETR5, it is less abundant in vegetative tissues. Taken together, ethylene perception in tomato is potentially quite complex, with at least five structurally divergent, putative receptor family members exhibiting significant variation in expression levels throughout development.

  4. Tomato FRUITFULL homologs regulate fruit ripening via ethylene biosynthesis.

    Science.gov (United States)

    Shima, Yoko; Fujisawa, Masaki; Kitagawa, Mamiko; Nakano, Toshitsugu; Kimbara, Junji; Nakamura, Nobutaka; Shiina, Takeo; Sugiyama, Junichi; Nakamura, Toshihide; Kasumi, Takafumi; Ito, Yasuhiro

    2014-01-01

    Certain MADS-box transcription factors play central roles in regulating fruit ripening. RIPENING INHIBITOR (RIN), a tomato MADS-domain protein, acts as a global regulator of ripening, affecting the climacteric rise of ethylene, pigmentation changes, and fruit softening. Previously, we showed that two MADS-domain proteins, the FRUITFULL homologs FUL1 and FUL2, form complexes with RIN. Here, we characterized the FUL1/FUL2 loss-of-function phenotype in co-suppressed plants. The transgenic plants produced ripening-defective fruits accumulating little or no lycopene. Unlike a previous study on FUL1/FUL2 suppressed tomatoes, our transgenic fruits showed very low levels of ethylene production, and this was associated with suppression of the genes for 1-aminocyclopropane-1-carboxylic acid synthase, a rate-limiting enzyme in ethylene synthesis. FUL1/FUL2 suppression also caused the fruit to soften in a manner independent of ripening, possibly due to reduced cuticle thickness in the peel of the suppressed tomatoes.

  5. Role of polyamines and ethylene as modulators of plant senescence

    Indian Academy of Sciences (India)

    S Pandey; S A Ranade; P K Nagar; Nikhil Kumar

    2000-09-01

    Under optimal conditions of growth, senescence, a terminal phase of development, sets in after a certain physiological age. It is a dynamic and closely regulated developmental process which involves an array of changes at both physiological and biochemical levels including gene expression. A large number of biotic and abiotic factors accelerate the process. Convincing evidence suggests the involvement of polyamines (PAs) and ethylene in this process. Although the biosynthetic pathways of both PAs and ethylene are interrelated, S-adenosylmethionine (SAM) being a common precursor, their physiological functions are distinct and at times antagonistic, particularly during leaf and flower senescence and also during fruit ripening. This provides an effective means for regulation of their biosynthesis and also to understand the mechanism by which the balance between the two can be established for manipulating the senescence process. The present article deals with current advances in the knowledge of the interrelationship between ethylene and PAs during senescence which may open up new vistas of investigation for the future.

  6. Controlling the reactivity of chlorinated ethylenes with flavin mononucleotide hydroquinone.

    Science.gov (United States)

    Ciptadjaya, Christopher G E; Guo, Wen; Angeli, Jayni M; Obare, Sherine O

    2009-03-01

    Reduction rate constants of the chlorinated ethylenes cis-1,2-dichloroethylene (cis-DCE), trichloroethylene (TCE), and tetrachloroethylene (PCE) reacted with flavin mononucleotide hydroquinone (FMNH2) under anoxic conditions were investigated. FMNH2 was produced in methanol solvent by the photoreduction of FMN. In aqueous solution, FMN was not fully reduced to FMNH2 but instead yielded the semiquinone radical FMNH*. However, when FMN was anchored to nanocrystalline TiO2, band gap irradiation resulted in electron transfer from the TiO2 conduction band to FMN, thus yielding FMNH2. The FMNH2 generated in aqueous solution on the TiO2 surface was a stronger reductant toward chlorinated ethylenes, relative to FMNH2 in solution. Furthermore, by combining the reactivity of the TiO2 conduction band electrons [TiO2(e-(CB)] with FMNH2, reduction rate constants for the chlorinated ethylenes increased by 2 orders of magnitude relative to FMNH2 alone. The results show how biological molecules such as FMNH2 could have significant effects toward the remediation of organic pollutants.

  7. Metal catalyzed ethylene epoxidation: A comparative density functional theory study

    Institute of Scientific and Technical Information of China (English)

    Ruipeng Ren; Yongkang Lü; Xianyong Pang; Guichang Wang

    2011-01-01

    Ethylene epoxidation on Ag(111), Pt(111), Rh(111) and Mo(100) has been studied by density functional theory (DFT) calculations. The results show that the adsorption energies of possible adsorbed species involved in the ethylene epoxidation increase in the order: Ag<Pt<Rh<Mo, and the activation energies of the formation of epoxide (EtO) and acetaldehyde (Ac) follow the same order. Moreover, it is found that the smallest difference in the activation energies between EtO formation and Ac formation is shown on Ag. These results indicate that the metallic Ag shows the highest between activity and selectivity for ethylene epoxidation among the studied metal surfaces. Perhaps, the stability of OMME intermediate is the crucial factor in controlling the activity and selectivity. And the stronger the binding of OMME, the lower the activity and selectivity are. In addition, the relationships between the reaction enthalpy and activation energy on these four metal surfaces are investigated,and it is found that such a correlation is only applied for OMME(a) → EtO(a) and OMME(a) → Ac(a), while invalid for the case of C2H4(a) +O(a) → OMME(a).

  8. Ethylene signalling affects susceptibility of tomatoes to Salmonella

    Science.gov (United States)

    Marvasi, Massimiliano; Noel, Jason T; George, Andrée S; Farias, Marcelo A; Jenkins, Keith T; Hochmuth, George; Xu, Yimin; Giovanonni, Jim J; Teplitski, Max

    2014-01-01

    Fresh fruits and vegetables are increasingly recognized as important reservoirs of human pathogens, and therefore, significant attention has been directed recently to understanding mechanisms of the interactions between plants and enterics, like Salmonella. A screen of tomato cultivars for their susceptibility to Salmonella revealed significant differences in the ability of this human pathogen to multiply within fruits; expression of the Salmonella genes (cysB, agfB, fadH) involved in the interactions with tomatoes depended on the tomato genotype and maturity stage. Proliferation of Salmonella was strongly reduced in the tomato mutants with defects in ethylene synthesis, perception and signal transduction. While mutation in the ripening-related ethylene receptor Nr resulted only in a modest reduction in Salmonella numbers within tomatoes, strong inhibition of the Salmonella proliferation was observed in rin and nor tomato mutants. RIN and NOR are regulators of ethylene synthesis and ripening. A commercial tomato variety heterozygous for rin was less susceptible to Salmonella under the greenhouse conditions but not when tested in the field over three production seasons. PMID:24888884

  9. Large Eddy Simulation of High-Speed, Premixed Ethylene Combustion

    Science.gov (United States)

    Ramesh, Kiran; Edwards, Jack R.; Chelliah, Harsha; Goyne, Christopher; McDaniel, James; Rockwell, Robert; Kirik, Justin; Cutler, Andrew; Danehy, Paul

    2015-01-01

    A large-eddy simulation / Reynolds-averaged Navier-Stokes (LES/RANS) methodology is used to simulate premixed ethylene-air combustion in a model scramjet designed for dual mode operation and equipped with a cavity for flameholding. A 22-species reduced mechanism for ethylene-air combustion is employed, and the calculations are performed on a mesh containing 93 million cells. Fuel plumes injected at the isolator entrance are processed by the isolator shock train, yielding a premixed fuel-air mixture at an equivalence ratio of 0.42 at the cavity entrance plane. A premixed flame is anchored within the cavity and propagates toward the opposite wall. Near complete combustion of ethylene is obtained. The combustor is highly dynamic, exhibiting a large-scale oscillation in global heat release and mass flow rate with a period of about 2.8 ms. Maximum heat release occurs when the flame front reaches its most downstream extent, as the flame surface area is larger. Minimum heat release is associated with flame propagation toward the cavity and occurs through a reduction in core flow velocity that is correlated with an upstream movement of the shock train. Reasonable agreement between simulation results and available wall pressure, particle image velocimetry, and OH-PLIF data is obtained, but it is not yet clear whether the system-level oscillations seen in the calculations are actually present in the experiment.

  10. Intermolecular potential energy surface and thermophysical properties of ethylene oxide

    Energy Technology Data Exchange (ETDEWEB)

    Crusius, Johann-Philipp, E-mail: johann-philipp.crusius@uni-rostock.de; Hassel, Egon [Lehrstuhl für Technische Thermodynamik, Universität Rostock, 18059 Rostock (Germany); Hellmann, Robert; Bich, Eckard [Institut für Chemie, Universität Rostock, 18059 Rostock (Germany)

    2014-10-28

    A six-dimensional potential energy hypersurface (PES) for two interacting rigid ethylene oxide (C{sub 2}H{sub 4}O) molecules was determined from high-level quantum-chemical ab initio calculations. The counterpoise-corrected supermolecular approach at the MP2 and CCSD(T) levels of theory was utilized to determine interaction energies for 10178 configurations of two molecules. An analytical site-site potential function with 19 sites per ethylene oxide molecule was fitted to the interaction energies and fine tuned to agree with data for the second acoustic virial coefficient from accurate speed of sound measurements. The PES was validated by computing the second virial coefficient, shear viscosity, and thermal conductivity. The values of these properties are substantiated by the best experimental data as they tend to fall within the uncertainty intervals and also obey the experimental temperature functions, except for viscosity, where experimental data are insufficient. Due to the lack of reliable data, especially for the transport properties, our calculated values are currently the most accurate estimates for these properties of ethylene oxide.

  11. Auxin, ethylene and light in gravitropic growth: new insights

    Science.gov (United States)

    Edelmann, Hg; Sabovljevic, A.; Njio, G.; Roth, U.

    The regulation mechanism of gravitropic differential plant growth is commonly divided into three sequential processes: the perception of the gravistimulus (generally attributed to amyloplast sedimentation), the transduction of the perceived signal (of which very little is known), and the adequate differential growth response (generally attributed to asymmetric auxin redistribution). The detailled mechanism is still unresolved and remains to be elucidated in significant parts. Employing 2D SDS-PAGE /Q-TOF amongst other methods and strategies we studied the effect of different auxins on gravitropism of coleoptiles and hypocotyls. We also analyzed the effects of light and ethylene (synthesis and perception) on gravitropic growth of primary shoots and roots and analyzed the protein pattern with respect to the observed physiological effects. In coleoptiles, under the applied experimental conditions the effect of 2,4-dichlorophenoxy acetic acid (2,4 D) on gravitropism differed from the effect of indolylacetic acid (IAA), which was similar to the one observed in sunflower hypocotyls. In roots, the relevance of ethylene for gravitropic differential growth and the capacity to evade mechanical barriers during horizontal gravistimulation was analyzed in detail. A special focus was addressed on the physiological significance of the root cap. We will show that the relevance of ethylene for gravitropism has hitherto been misjudged. Further new findings and their implications for the regulation mechanism of gravitropism will be presented and discussed. Kramer et al., (2003) J. Ex. Bot. 54, (393), 2723-2732 Edelmann, H.G., (2002) J. Ex. Bot. 53, (375), 1825-1828

  12. Ethylene biosynthetic genes are differentially expressed during carnation (Dianthus caryophyllus L.) flower senescence.

    Science.gov (United States)

    ten Have, A; Woltering, E J

    1997-05-01

    Ethylene production and expression patterns of an 1-aminocyclopropane-1-carboxylic acid (ACC) oxidase (CARAO1) and of two ACC synthase (EC 4.4.1.14) genes (CARACC3 and CARAS1) were studied in floral organs of cut carnation flowers (Dianthus caryophyllus L.) cv. White Sim. During the vase life and after treatment of fresh flowers with ethylene, production of ethylene and expression of ethylene biosynthetic genes first started in the ovary followed by the styles and the petals. ACC oxidase was expressed in all the floral organs whereas, during the vase life, tissue-specific expression of the two ACC synthase genes was observed. After treatment with a high ethylene concentration, tissue specificity of the two ACC synthase genes was lost and only a temporal difference in expression remained. In styles, poor correlation between ethylene production and ACC synthase (CARAS1) gene expression was observed suggesting that either activity is regulated at the translational level or that the CARAS1 gene product requires an additional factor for activity. Isolated petals showed no increase in ethylene production and expression of ethylene biosynthetic genes when excised from the flower before the increase in petal ethylene production (before day 7); showed rapid cessation of ethylene production and gene expression when excised during the early phase of petal ethylene production (day 7) and showed a pattern of ethylene production and gene expression similar to the pattern observed in the attached petals when isolated at day 8. The interorgan regulation of gene expression and ethylene as a signal molecule in flower senescence are discussed.

  13. Highly efficient synthesis of monodisperse poly(ethylene glycols) and derivatives through macrocyclization of oligo(ethylene glycols).

    Science.gov (United States)

    Zhang, Hua; Li, Xuefei; Shi, Qiuyan; Li, Yu; Xia, Guiquan; Chen, Long; Yang, Zhigang; Jiang, Zhong-Xing

    2015-03-16

    A macrocyclic sulfate (MCS)-based approach to monodisperse poly(ethylene glycols) (M-PEGs) and their monofunctionalized derivatives has been developed. Macrocyclization of oligo(ethylene glycols) (OEGs) provides MCS (up to a 62-membered macrocycle) as versatile precursors for a range of monofunctionalized M-PEGs. Through iterative nucleophilic ring-opening reactions of MCS without performing group protection and activation, a series of M-PEGs, including the unprecedented 64-mer (2850 Da), can be readily prepared. Synthetic simplicity coupled with versatility of this new strategy may pave the way for broader applications of M-PEGs. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. Selective surface modification of ethylene-vinyl acetate and ethylene polymer blend by UV–ozone treatment

    OpenAIRE

    Jofre-Reche, José Antonio; Martín-Martínez, José Miguel

    2013-01-01

    Ethylene-vinyl acetate (EVA) copolymers intended for sport sole manufacturing may contain noticeable amounts of polyethylene (LDPE) for improving abrasion resistance and decrease cost; however, this blend (EVA–PE) had low polarity and showed poor adhesion. In this study an effective environmentally friendly and fast surface treatment based on UV–ozone has been used to increase the wettability, polarity and roughness of EVA–PE material. Both the length of the UV–ozone treatment and the distanc...

  15. Ethylene, a Hormone at the Center-Stage of Nodulation.

    Science.gov (United States)

    Guinel, Frédérique C

    2015-01-01

    Nodulation is the result of a beneficial interaction between legumes and rhizobia. It is a sophisticated process leading to nutrient exchange between the two types of symbionts. In this association, within a nodule, the rhizobia, using energy provided as photosynthates, fix atmospheric nitrogen and convert it to ammonium which is available to the plant. Nodulation is recognized as an essential process in nitrogen cycling and legume crops are known to enrich agricultural soils in nitrogenous compounds. Furthermore, as they are rich in nitrogen, legumes are considered important as staple foods for humans and fodder for animals. To tightly control this association and keep it mutualistic, the plant uses several means, including hormones. The hormone ethylene has been known as a negative regulator of nodulation for almost four decades. Since then, much progress has been made in the understanding of both the ethylene signaling pathway and the nodulation process. Here I have taken a large view, using recently obtained knowledge, to describe in some detail the major stages of the process. I have not only reviewed the steps most commonly covered (the common signaling transduction pathway, and the epidermal and cortical programs), but I have also looked into steps less understood (the pre-infection step with the plant defense response, the bacterial release and the formation of the symbiosome, and nodule functioning and senescence). After a succinct review of the ethylene signaling pathway, I have used the knowledge obtained from nodulation- and ethylene-related mutants to paint a more complete picture of the role played by the hormone in nodule organogenesis, functioning, and senescence. It transpires that ethylene is at the center of this effective symbiosis. It has not only been involved in most of the steps leading to a mature nodule, but it has also been implicated in host immunity and nodule senescence. It is likely responsible for the activation of other hormonal

  16. Hydrogen sulfide alleviates postharvest ripening and senescence of banana by antagonizing the effect of ethylene.

    Science.gov (United States)

    Ge, Yun; Hu, Kang-Di; Wang, Sha-Sha; Hu, Lan-Ying; Chen, Xiao-Yan; Li, Yan-Hong; Yang, Ying; Yang, Feng; Zhang, Hua

    2017-01-01

    Accumulating evidence shows that hydrogen sulfide (H2S) acts as a multifunctional signaling molecule in plants, whereas the interaction between H2S and ethylene is still unclear. In the present study we investigated the role of H2S in ethylene-promoted banana ripening and senescence by the application of ethylene released from 1.0 g·L-1 ethephon solution or H2S with 1 mM sodium hydrosulfide (NaHS) as the donor or in combination. Fumigation with ethylene was found to accelerate banana ripening and H2S treatment effectively alleviated ethylene-induced banana peel yellowing and fruit softening in parallel with decreased activity of polygalacturonase (PG). Ethylene+H2S treatment also delayed the decreases in chlorophyll and total phenolics, and increased the accumulation of flavonoid, whereas decreased the contents of carotenoid, soluble protein in banana peel and reducing sugar in pulp compared with ethylene treatment alone. Besides, ethylene+H2S treatment suppressed the accumulation of superoxide radicals (·O2-), hydrogen peroxide (H2O2) and malondialdehyde (MDA) which accumulated highly in ethylene-treated banana peels. Furthermore H2S enhanced total antioxidant capacity in ethylene-treated banana peels with the 2,2'-azobis(3-ethylbenz-thiazoline-6-sulfonic acid (ABTS) assay. The result of quantitative real-time PCR showed that the combined treatment of ethylene with H2S down-regulated the expression of ethylene synthesis genes MaACS1, MaACS2 and MaACO1 and pectate lyase MaPL compared with ethylene treatment, while the expression of ethylene receptor genes MaETR, MaERS1 and MaERS2 was enhanced in combination treatment compared with ethylene alone. In all, it can be concluded that H2S alleviates banana fruit ripening and senescence by antagonizing the effect of ethylene through reduction of oxidative stress and inhibition of ethylene signaling pathway.

  17. Poly(ethylene glycol-poly(tetrahydrofuran-poly(ethylene glycol triblock copolymer : Synthesis, crystallization behavior and novel morphology

    Directory of Open Access Journals (Sweden)

    X. Q. Liao

    2013-05-01

    Full Text Available Poly(ethylene glycol-poly(tetrahydrofuran-poly(ethylene glycol (PEG-PTHF-PEG triblock copolymer was synthesized by ring-opening polymerization of ethylene oxide using sodium alcoholate of PTHF as the macroinitiator. Its crystallization behavior and formation mechanisms of different crystal structures were studied. The study showed that the molecular weight of PEG-PTHF-PEG exhibited a significant effect on its crystallization: that is, with the increase of the copolymer’s molecular weight, the crystallizability of PTHF blocks decreased gradually, which led to the transition of copolymer from crystalline-crystalline to crystalline-amorphous. By adjusting the total molecular weight of triblock copolymer, the crystallization process can be effectively controlled, and as a result, different spherulite structures were obtained. Particularly, when PTHF blocks became amorphous, novel double concentric spherulites were observed. The morphological structures were studied by differential scanning calorimetry (DSC, Fourier transform infrared spectroscopy (FTIR, scanning electron microscope (SEM, polarized optical microscopy (POM, and its crystalline process was investigated.

  18. Post harvest ripening of oil palm fruit is accelerated by application of exogenous ethylene

    Directory of Open Access Journals (Sweden)

    Narumol Nualwijit

    2014-06-01

    Full Text Available Experiments were conducted with fresh fully mature fruit bunches of Tenera variety oil-palm. Palm fruit bunches were exposed to 0, 250, 500 or 1000 mlL-1 ethylene for 24 hours. Each fruit bunch was evaluated in three separate sections: the bottom, the middle, and the top. The exogenous ethylene treatments significantly hastened palm fruit ripening, quantified by an increase in the fruit peel coloring that turns from black to reddish orange. Ethylene treatments also significantly eased detaching the fruit, by reducing the tension force required. Total oil contents of fruit increased with 1000 mlL-1 ethylene treatment. Free fatty acids (FFA in untreated palm fruit, especially in the bottom section, were at their highest levels 2 days after harvest, and the FFA levels were lowered by ethylene treatments. In summary, exogenous ethylene fumigation accelerated the ripening of oil palm fruit, increased oil yield, and decreased the FFA levels.

  19. Involvement of ethylene in the accumulation of esculeoside A during fruit ripening of tomato (Solanum lycopersicum).

    Science.gov (United States)

    Iijima, Yoko; Fujiwara, Yukio; Tokita, Takeaki; Ikeda, Tsuyoshi; Nohara, Toshihiro; Aoki, Koh; Shibata, Daisuke

    2009-04-22

    The composition of glycoalkaloids in tomato fruit changes with ripening. However, it has not been clarified whether the accumulation of glycoalkaloids is controlled by the ripening-inducing phytohormone, ethylene. Here, we report the effect of ethylene on the accumulation of tomato fruit glycoalkaloids. We investigated the effect of exogenously applied ethylene. In response to ethylene treatment, the content of alpha-tomatine decreased, whereas the content of esculeoside A increased. Next, we analyzed the fruits of ripening mutants, rin, nor, and Nr. In fruits of these mutant lines, the level of accumulation of esculeoside A decreased, whereas alpha-tomatine accumulated to higher levels than in wild-type fruit. These results demonstrated that the esculeoside A accumulation was associated with production and perception of ethylene. Additionally, the accumulation profiles of the intermediate metabolites of esculeoside A biosynthesis in ripening mutant fruits suggest that a glycosylation step in the putative pathway from alpha-tomatine to esculeoside A depends on ethylene.

  20. Commercial Application of CPP for Producing Ethylene and Propylene from Heavy Oil Feed

    Institute of Scientific and Technical Information of China (English)

    Hou Dianguo; Xie Chaogang; Wang Xieqing

    2003-01-01

    A new process named CPP (Catalytic Pyrolysis Process) for producing ethylene andpropylene from heavy oil feedstock has been developed. The catalyst CEP was specially designedfor this process, which has bi-functional catalytic activities for both carbonium ion reaction andfree radical reaction, so as to maximize the yields of ethylene and propylene. The commercial trialshowed that the yield of ethylene and propylene was 20.37% and 18.23% respectively inmaximum ethylene operation with Daqing AR as feedstock, and the yield of ethylene and propylenewas 9.77% and 24.60% respectively in maximum propylene operation by using the same feedstock.Compared with steam cracker, the feed cost of CPP is much lower for producing ethylene andpropylene.

  1. The effect of ethylene on root growth of Zea mays seedlings

    Science.gov (United States)

    Whalen, M. C.; Feldman, L. J.

    1988-01-01

    The control of primary root growth in Zea mays cv. Merit by ethylene was examined. At applied concentrations of ethylene equal to or greater than 0.1 microliter L-1, root elongation during 24 h was inhibited. The half-maximal response occurred at 0.6 microliter L-1 and the response saturated at 6 microliters L-1. Inhibition of elongation took place within 20 min. However, after ethylene was removed, elongation recovered to control values within 15 min. Root elongation was also inhibited by green light. The inhibition caused by a 24-h exposure to ethylene was restricted to the elongating region just behind the apex, with inhibition of cortical cell elongation being the primary contributor to the effect. Based on use of 2,5-norbornadiene, a gaseous competitive inhibitor of ethylene, it was concluded that endogenous ethylene normally inhibits root elongation.

  2. [The role of nitric oxide in ethylene-induced stomatal closure in Vicia faba L].

    Science.gov (United States)

    Li, Jie; Qiu, Li-Yan; Zhao, Fang-Gui; Hou, Li-Xia; Liu, Xin

    2007-08-01

    The effects of nitric oxide (NO) and ethylene on Vicia faba L. stomatal movement were studied. The results showed that NO donor SNP (sodium nitroprusside) 10 micromol/L and ethylene 0.04% could induce stomatal closure distinctly and they could promote stomatal closure when treated together. When treated with AVG (an inhibitor of ethylene synthesis), c-PTIO (a specific scavenger of NO) and NaN(3) (an inhibitor of NR), the effects of NO- and ethylene-induced stomatal closure were inhibited but the inhibitor of nitric oxide synthase (NOS) had little effect. We presumed that there was coordinative effect between NO and ethylene in regulation of stomatal closure; ethylene could induce stomatal closure by regulating the production of nitrate reductase (NR)-dependent NO.

  3. A new ethylene glycol-silane monolayer for highly-specific DNA detection on Silicon Chips

    OpenAIRE

    2010-01-01

    Monolayer thin films with ethylene-glycol function onto gold surfaces by using thiols have been extensively investigated. They have been proposed as precursors for applications to bio-detection, where their hydrophilic character improves both specificity and sensitivity. The aim of this letter is to characterize ethylene-glycol monolayer precursors formed onto silicon chips by using silanes. The importance of the ethylene-glycol function is demonstrated by comparing with the well known 3-Amin...

  4. NREL Produces Ethylene via Photosynthesis; Breakthrough Offers Cleaner Alternative for Transportation Fuels (Fact Sheet)

    Energy Technology Data Exchange (ETDEWEB)

    2013-08-01

    NREL scientists have demonstrated a way to produce ethylene through photosynthesis, a breakthrough that could lead to more environmentally friendly ways to produce a variety of materials, chemicals, and transportation fuels. The scientists introduced a gene into a cyanobacterium and demonstrated that the organism remains stable through at least four generations, producing ethylene gas that can be easily captured. In the laboratory, the organism, Synechocystis sp. PCC 6803, produced 720 milligrams of ethylene per liter each day.

  5. Epidemiologic support for ethylene oxide as a cancer-causing agent.

    Science.gov (United States)

    Hogstedt, C; Aringer, L; Gustavsson, A

    1986-03-28

    The mortality and incidence of cancer in three groups of workers with occupational exposure to ethylene oxide have been assessed. Eight cases of leukemia have occurred among 733 ethylene oxide-exposed workers compared with an expected 0.8 cases. Six cases of stomach cancer have been reported compared with 0.65 cases expected. These epidemiologic results provide support for an increased risk of malignancy in individuals with extended and intermittent exposure to low concentrations of ethylene oxide.

  6. Enzymatic Modification of Poly (ethylene terephthalate) Fiber with Lipase from Aspergillus oryzae

    Institute of Scientific and Technical Information of China (English)

    WANG Xiao-hua; LU Da-nian; SHAO Zhi-yu; HONG Feng

    2007-01-01

    Lipase preparation from Aspergiilus oryzae could act on ester bonds on the surface of poly (ethylene terephthalate) fibers and a possible hydrolytic product mono (2-hydroxyethyl) terephthalate was released. After the iipase modification, there were more carboxyl groups on the treated poly (ethylene terephthalate) fabric surface that resulted in binding with mote cationic dyes. Increased hydrophilicity and antistatic ability of poly (ethylene terephthalate) samples were found based on moisture regain, water contact angle and static half decay time.

  7. Ethylene responses in rice roots and coleoptiles are differentially regulated by a carotenoid isomerase-mediated abscisic acid pathway.

    Science.gov (United States)

    Yin, Cui-Cui; Ma, Biao; Collinge, Derek Phillip; Pogson, Barry James; He, Si-Jie; Xiong, Qing; Duan, Kai-Xuan; Chen, Hui; Yang, Chao; Lu, Xiang; Wang, Yi-Qin; Zhang, Wan-Ke; Chu, Cheng-Cai; Sun, Xiao-Hong; Fang, Shuang; Chu, Jin-Fang; Lu, Tie-Gang; Chen, Shou-Yi; Zhang, Jin-Song

    2015-04-01

    Ethylene and abscisic acid (ABA) act synergistically or antagonistically to regulate plant growth and development. ABA is derived from the carotenoid biosynthesis pathway. Here, we analyzed the interplay among ethylene, carotenoid biogenesis, and ABA in rice (Oryza sativa) using the rice ethylene response mutant mhz5, which displays a reduced ethylene response in roots but an enhanced ethylene response in coleoptiles. We found that MHZ5 encodes a carotenoid isomerase and that the mutation in mhz5 blocks carotenoid biosynthesis, reduces ABA accumulation, and promotes ethylene production in etiolated seedlings. ABA can largely rescue the ethylene response of the mhz5 mutant. Ethylene induces MHZ5 expression, the production of neoxanthin, an ABA biosynthesis precursor, and ABA accumulation in roots. MHZ5 overexpression results in enhanced ethylene sensitivity in roots and reduced ethylene sensitivity in coleoptiles. Mutation or overexpression of MHZ5 also alters the expression of ethylene-responsive genes. Genetic studies revealed that the MHZ5-mediated ABA pathway acts downstream of ethylene signaling to inhibit root growth. The MHZ5-mediated ABA pathway likely acts upstream but negatively regulates ethylene signaling to control coleoptile growth. Our study reveals novel interactions among ethylene, carotenogenesis, and ABA and provides insight into improvements in agronomic traits and adaptive growth through the manipulation of these pathways in rice.

  8. Further studies of auxin and ACC induced feminization in the cucumber plant using ethylene inhibitors

    Science.gov (United States)

    Takahashi, H.; Jaffe, M. J.

    1984-01-01

    The present study was designed to establish the role of an essential hormone controlling sex expression in cucumber. A potent anti-ethylene agent, AgNO3, completely inhibited pistillate flower formation caused by IAA, ACC or ethephon. Inhibitors of ethylene biosynthesis, AVG and CoCl2 also suppressed feminization due to exogenous IAA or ACC. Though AVG also suppressed ethephon-induced feminization, this may be due to the second effect of AVG rather than the effect on ACC biosynthesis. These results confirm that ethylene is a major factor regulating feminization and that exogenous auxin induces pistillate flower formation through its stimulation of ethylene production, rather than ACC production.

  9. Glass transition behavior of ternary disaccharide-ethylene glycol-water solutions

    Science.gov (United States)

    Yu, Tongxu; Zhao, Lishan; Wang, Qiang; Cao, Zexian

    2017-06-01

    Glass transition behavior of ternary disaccharide-ethylene glycol-water solutions, in reference to that of the binary combinations, has been investigated towards a better understanding of their cryoprotective ability. In water-deficient solutions, the disaccharides, including trehalose, sucrose and maltose, can associate with more than 100 ethylene glycol molecules to form amorphous complex, one order of magnitude larger than the corresponding hydration numbers. In water-rich solutions, a second glass transition emerges with increasing molar fraction of ethylene glycol, indicating the possible synergy of disaccharides and ethylene glycol in vitrification of the ternary aqueous solution.

  10. Current understanding on ethylene signaling in plants: the influence of nutrient availability.

    Science.gov (United States)

    Iqbal, Noushina; Trivellini, Alice; Masood, Asim; Ferrante, Antonio; Khan, Nafees A

    2013-12-01

    The plant hormone ethylene is involved in many physiological processes, including plant growth, development and senescence. Ethylene also plays a pivotal role in plant response or adaptation under biotic and abiotic stress conditions. In plants, ethylene production often enhances the tolerance to sub-optimal environmental conditions. This role is particularly important from both ecological and agricultural point of views. Among the abiotic stresses, the role of ethylene in plants under nutrient stress conditions has not been completely investigated. In literature few reports are available on the interaction among ethylene and macro- or micro-nutrients. However, the published works clearly demonstrated that several mineral nutrients largely affect ethylene biosynthesis and perception with a strong influence on plant physiology. The aim of this review is to revisit the old findings and recent advances of knowledge regarding the sub-optimal nutrient conditions on the effect of ethylene biosynthesis and perception in plants. The effect of deficiency or excess of the single macronutrient or micronutrient on the ethylene pathway and plant responses are reviewed and discussed. The synergistic and antagonist effect of the different mineral nutrients on ethylene plant responses is critically analyzed. Moreover, this review highlights the status of information between nutritional stresses and plant response, emphasizing the topics that should be further investigated. Copyright © 2013 Elsevier Masson SAS. All rights reserved.

  11. Inhibition of ethylene production by putrescine alleviates aluminium-induced root inhibition in wheat plants.

    Science.gov (United States)

    Yu, Yan; Jin, Chongwei; Sun, Chengliang; Wang, Jinghong; Ye, Yiquan; Zhou, Weiwei; Lu, Lingli; Lin, Xianyong

    2016-01-08

    Inhibition of root elongation is one of the most distinct symptoms of aluminium (Al) toxicity. Although putrescine (Put) has been identified as an important signaling molecule involved in Al tolerance, it is yet unknown how Put mitigates Al-induced root inhibition. Here, the possible mechanism was investigated by using two wheat genotypes differing in Al resistance: Al-tolerant Xi Aimai-1 and Al-sensitive Yangmai-5. Aluminium caused more root inhibition in Yangmai-5 and increased ethylene production at the root apices compared to Xi Aimai-1, whereas the effects were significantly reversed by ethylene biosynthesis inhibitors. The simultaneous exposure of wheat seedlings to Al and ethylene donor, ethephon, or ethylene biosynthesis precursor, 1-aminocyclopropane-1-carboxylic acid (ACC), increased ethylene production and aggravated root inhibition, which was more pronounced in Xi Aimai-1. In contrast, Put treatment decreased ethylene production and alleviated Al-induced root inhibition in both genotypes, and the effects were more conspicuous in Yangmai-5. Furthermore, our results indicated that Al-induced ethylene production was mediated by ACC synthase (ACS) and ACC oxidase, and that Put decreased ethylene production by inhibiting ACS. Altogether, these findings indicate that ethylene is involved in Al-induced root inhibition and this process could be alleviated by Put through inhibiting ACS activity.

  12. Health-hazard evaluation report HETA 83-335-1618, Kendall Company, Augusta, Georgia. [Ethylene oxide

    Energy Technology Data Exchange (ETDEWEB)

    Seligman, P.; Gorman, R.

    1985-08-01

    Environmental and breathing-zone samples were analyzed for ethylene oxide at the Kendall Company, Augusta, Georgia in August, 1983 and July and August, 1984. The evaluation was requested confidentially to investigate employee complaints of eye irritation and neurologic symptoms and concern over an excessive number of miscarriages. Physicians at the Medical College of Georgia had reported cases of peripheral neuropathy and cataracts related to ethylene-oxide exposure. Twenty-one employees were interviewed. Company medical records were reviewed. Ethylene-oxide concentrations ranged from nondetectable to 0.83 part per million (ppm). The OSHA standard for ethylene oxide is 1.00 ppm. Grab samples taken during sterilizer down/loading contained 0.3 to 25.0ppm ethylene oxide. Medical records confirmed three cases of neuropathy and four of cataracts. Headache, eye irritation, and fatigue were the most prominent symptoms reported. Many of these symptoms were resolved when ethylene oxide was removed from the alcohol wipes. Five of six miscarriages were not occupationally related. The authors conclude that cases of peripheral neuropathy and cataracts among ethylene-oxide sterilizer operators can be related to past exposures, which were higher. Recommendations include using engineering controls to reduce ethylene-oxide exposure further and complying with OSHA recommendations in monitoring employees exposed to action-level concentrations of 0.5ppm ethylene oxide.

  13. Response to Xanthomonas campestris pv. vesicatoria in tomato involves regulation of ethylene receptor gene expression.

    Science.gov (United States)

    Ciardi, J A; Tieman, D M; Lund, S T; Jones, J B; Stall, R E; Klee, H J

    2000-05-01

    Although ethylene regulates a wide range of defense-related genes, its role in plant defense varies greatly among different plant-microbe interactions. We compared ethylene's role in plant response to virulent and avirulent strains of Xanthomonas campestris pv. vesicatoria in tomato (Lycopersicon esculentum Mill.). The ethylene-insensitive Never ripe (Nr) mutant displays increased tolerance to the virulent strain, while maintaining resistance to the avirulent strain. Expression of the ethylene receptor genes NR and LeETR4 was induced by infection with both virulent and avirulent strains; however, the induction of LeETR4 expression by the avirulent strain was blocked in the Nr mutant. To determine whether ethylene receptor levels affect symptom development, transgenic plants overexpressing a wild-type NR cDNA were infected with virulent X. campestris pv. vesicatoria. Like the Nr mutant, the NR overexpressors displayed greatly reduced necrosis in response to this pathogen. NR overexpression also reduced ethylene sensitivity in seedlings and mature plants, indicating that, like LeETR4, this receptor is a negative regulator of ethylene response. Therefore, pathogen-induced increases in ethylene receptors may limit the spread of necrosis by reducing ethylene sensitivity.

  14. Uncoupling Auxin and Ethylene Effects in Transgenic Tobacco and Arabidopsis Plants.

    Science.gov (United States)

    Romano, CP; Cooper, ML; Klee, HJ

    1993-01-01

    Overproduction of auxin in transgenic plants also results in the overproduction of ethylene. Plants overproducing both auxin and ethylene display inhibition of stem elongation and growth, increased apical dominance, and leaf epinasty. To determine the relative roles of auxin and ethylene in these processes, transgenic tobacco and Arabidopsis plants expressing the auxin-overproducing tryptophan monooxygenase transgene were crossed to plants expressing an ethylene synthesis-inhibiting 1-aminocyclopropane-1-carboxylate deaminase transgene. Tobacco and Arabidopsis plants with elevated auxin and normal levels of ethylene were obtained by this strategy. Transgenic auxin-overproducing Arabidopsis plants were also crossed with the ethylene-insensitive ein1 and ein2 mutants. Analysis of these plants indicates that apical dominance and leaf epinasty are primarily controlled by auxin rather than ethylene. However, ethylene is partially responsible for the inhibition of stem elongation observed in auxin-overproducing tobacco. Finally, these data show that auxin overproduction can be effectively uncoupled from ethylene overproduction in transgenic plants to enable direct manipulation of plant morphology for agronomic and horticultural purposes. PMID:12271061

  15. Synthesis of amphiphilic diblock copolymer for surface modification of Ethylene-Norbornene copolymers

    DEFF Research Database (Denmark)

    Levinsen, Simon; Svendsen, Winnie Edith; Horsewell, Andy

    2014-01-01

    -norbornene copolymer TOPAS. Through matching of the radius of gyration for the model polymer and TOPAS the miscibility was achieved. The poly(ethylene-1-butene) polymer was synthesized from a hydrogenated anionic polymerized polybutadiene polymer. As hydrophilic block poly(ethylene oxide) was subsequently added also...... consisting of a bulk material compatible block and a hydrophilic block. To utilize the possibility of incorporating diblock copolymers into ethylenenorbornene copolymers, we have in this work developed a model poly(ethylene-1-butene) polymer compatible with the commercial available ethylene...

  16. Ethylene Removal by a Biofilter with Immobilized Bacteria

    Science.gov (United States)

    Elsgaard, Lars

    1998-01-01

    A biofilter which eliminated ethylene (C2H4) from the high parts-per-million range to levels near the limit for plant hormonal activity (0.01 to 0.1 ppm) was developed. Isolated ethylene-oxidizing bacteria were immobilized on peat-soil in a biofilter (687 cm3) and subjected to an atmospheric gas flow (73.3 ml min−1) with 2 or 117 ppm of C2H4. Ethylene was eliminated to a minimum level of 0.017 ppm after operation with 2.05 ppm of C2H4 for 16 days. Also, the inlet C2H4 concentration of 117 ppm was reduced to biofilter. The maximal C2H4 elimination capacity of the biofilter was 21 g of C2H4 m−3 day−1 during operation with 117 ppm of C2H4 in the inlet gas. However, for the first 0- to 5-cm segment of the biofilter, an elimination capacity of 146 g of C2H4 m−3 day−1 was calculated. Transition of the biofilter temperature from 21 to 10°C caused a 1.6-fold reduction in the C2H4 removal rate, which was reversed during operation for 18 days. Batch experiments with inoculated peat-soil demonstrated that C2H4 removal still occurred after storage at 2, 8, and 20°C for 2, 3, and 4 weeks. However, the C2H4 removal rate decreased with increasing storage time and was reduced by ca. 50% after storage for 2 weeks at all three temperatures. The biofilter could be a suitable tool for C2H4 removal in, e.g., horticultural storage facilities, since it (i) removed C2H4 to 0.017 ppm, (ii) had a good operational stability, and (iii) operated efficiently at 10°C. PMID:9797261

  17. Anaphylaxis to ethylene oxide - a rare and overlooked phenomenon?

    DEFF Research Database (Denmark)

    Bache, Søren; Petersen, J T; Garvey, L H

    2011-01-01

    Spina bifida patients have been reported to be at increased risk of anaphylactic reactions during general anaesthesia. Following a reaction, latex is often incriminated as spina bifida patients are known to have an increased incidence of latex allergy. Ethylene oxide (EO) has recently been...... the case of a spina bifida patient with a known latex allergy, where EO was found to be the cause of an anaphylactic reaction during general anaesthesia. In addition, we describe measures taken during preparation of a subsequent general anaesthesia to minimise exposure to EO. Spina bifida patients seem...

  18. Evaluation of the Inhalation Carcinogenicity of Ethylene Oxide ...

    Science.gov (United States)

    EPA is initiating a public comment period prior to peer review of the scientific basis supporting the human health hazard and dose-response assessment of ethylene oxide (cancer) that will appear in the Integrated Risk Information System (IRIS) database. EPA seeks external peer review on how the Agency responded to the SAB panel recommendations, the exposure-response modeling of epidemiologic data, including new analyses since the 2007 external peer review, and on the adequacy, transparency, and clarity of the revised draft. The peer review will include an opportunity for the public to address the peer reviewers.

  19. THE FAR-INFRARED ROTATIONAL SPECTRUM OF ETHYLENE OXIDE

    Energy Technology Data Exchange (ETDEWEB)

    Medcraft, Chris; Thompson, Christopher D.; McNaughton, Don [School of Chemistry, Monash University, Wellington Road, Clayton, Victoria 3800 (Australia); Robertson, Evan G. [Department of Chemistry, La Trobe Institute of Molecular Sciences, La Trobe University, Bundoora, Victoria 3086 (Australia); Appadoo, Dominique R. T., E-mail: donald.mcnaughton@monash.edu [Australian Synchrotron, 800 Blackburn Road, Clayton, Victoria 3168 (Australia)

    2012-07-01

    High-resolution FTIR spectra of ethylene oxide have been measured in the far-infrared region using synchrotron radiation. A total of 1182 lines between 15 and 73 cm{sup -1} were assigned, with J{sub max} = 64, expanding upon previous studies that had recorded spectra up to 12 cm{sup -1}, J{sub max} = 49. All available data were co-fitted to provide greatly imp- roved rotational constants for the ground vibrational state that are capable of predicting transitions up to 73 cm{sup -1}.

  20. Modelling graphene quantum dot functionalization via ethylene-dinitrobenzoyl

    Energy Technology Data Exchange (ETDEWEB)

    Noori, Keian; Giustino, Feliciano [Department of Materials, University of Oxford, Parks Road, Oxford OX1 3PH (United Kingdom); Hübener, Hannes [Department of Materials, University of Oxford, Parks Road, Oxford OX1 3PH (United Kingdom); Nano-Bio Spectroscopy Group and European Theoretical Spectroscopy Facility (ETSF), Universidad del País Vasco CFM CSIC-UPV/EHU-MPC & DIPC, Av. Tolosa 72, 20018 San Sebastián (Spain); Kymakis, Emmanuel [Center of Materials Technology and Photonics & Electrical Engineering Department, Technological Educational Institute (TEI) of Crete, Heraklion, 71004 Crete (Greece)

    2016-03-21

    Ethylene-dinitrobenzoyl (EDNB) linked to graphene oxide has been shown to improve the performance of graphene/polymer organic photovoltaics. Its binding conformation on graphene, however, is not yet clear, nor have its effects on work function and optical absorption been explored more generally for graphene quantum dots. In this report, we clarify the linkage of EDNB to GQDs from first principles and show that the binding of the molecule increases the work function of graphene, while simultaneously modifying its absorption in the ultraviolet region.

  1. Simulation of soot size distribution in an ethylene counterflow flame

    KAUST Repository

    Zhou, Kun

    2014-01-06

    Soot, an aggregate of carbonaceous particles produced during the rich combustion of fossil fuels, is an undesirable pollutant and health hazard. Soot evolution involves various dynamic processes: nucleation soot formation from polycyclic aromatic hydrocarbons (PAHs) condensation PAHs condensing on soot particle surface surface processes hydrogen-abstraction-C2H2-addition, oxidation coagulation two soot particles coagulating to form a bigger particle This simulation work investigates soot size distribution and morphology in an ethylene counterflow flame, using i). Chemkin with a method of moments to deal with the coupling between vapor consumption and soot formation; ii). Monte Carlo simulation of soot dynamics.

  2. IRIS Toxicological Review of Ethylene Glycol Mono-Butyl ...

    Science.gov (United States)

    EPA released the draft report, Toxicological Review for Ethylene Glycol Mono-Butyl Ether , that was distributed to Federal agencies and White House Offices for comment during the Science Discussion step of the IRIS Assessment Development Process. Comments received from other Federal agencies and White House Offices are provided below with external peer review panel comments. EPA is conducting a peer review of the scientific basis supporting the human health hazard and dose-response assessment of EGBE that will appear on the Integrated Risk Information System (IRIS) database.

  3. Fouling and Antifouling of Depetanizer in Ethylene Units

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Factors affecting fouling of depentanizer in ethylene units were explored through study of thecomposition of pyrolysis gasoline, C5 distillate and fouling deposits from the depentanizer while takinginto consideration the processing parameters. A variety of antifouling measures, in particular the injec-tion of a special anti-fouling agent into the Cs gas phase pipeline and the C5 distillate reflux pipelinewere introduced. Commercial evaluation test of a multifunctional anti-fouling agent, the RIPP-1404anti-fouling agent, was also described.

  4. Fouling and Antifouling of Depetanizer in Ethylene Units

    Institute of Scientific and Technical Information of China (English)

    DongZhongjie; LiYunlong; 等

    2002-01-01

    Factors affecting fouling of depentanizer in ethylene units were explored through study of the composition of pyrolysis gasoline,C5 distillate and fouling deposits from the depentanizer while taking into consideration the processing parameters.A variety of antifouling measures,in particular the injec-tion of a special anti-fouling agent into the C5 gas phase pipeline and the C5 distillate reflux pipeline were introduced.Commercial evaluation test of a multifunctional anti-fouling agent,the RIPP-1404 anti-fouling agent,was also described.

  5. Thermal Behavior of Poly(trimethylene-co-ethylene terephthalate)

    Institute of Scientific and Technical Information of China (English)

    Yong XU; Sheng Rong YE; Jin Wen QIAN

    2005-01-01

    Poly (trimethylene-co-ethylene terephthalate) with various compositions of diol has been synthesized. The crystallization of copolyesters with high comonomer content was observed by both wide-angle X-ray diffraction (WAXD) and differential scanning calorimetry (DSC). It was found that the copolyesters become less crystallizable with the involvement of the comonomer,the crystals of crystallizable copolyesters come from PTT or PET homopolymers. The glass transition temperature (Tg) of the copolyester increases with increasing PET component in the copolyester, and the relationship between Tg and composition obey both Fox equation and additive law, the former is better in describing this relationship.

  6. Electron beam irradiation effects on poly(ethylene terephthalate)

    Energy Technology Data Exchange (ETDEWEB)

    Burillo, G. [Departamento de Quimica de Radiaciones y Radioquimica, Instituto de Ciencias Nucleares, Universidad Nacional Autonoma de Mexico, Ciudad Universitaria, Mexico, DF 04510 (Mexico)], E-mail: burillo@nucleares.unam.mx; Tenorio, L.; Bucio, E. [Departamento de Quimica de Radiaciones y Radioquimica, Instituto de Ciencias Nucleares, Universidad Nacional Autonoma de Mexico, Ciudad Universitaria, Mexico, DF 04510 (Mexico); Adem, E. [Departamento de Fisica Experimental, Instituto de Fisica, Universidad Nacional Autonoma de Mexico, Ciudad Universitaria, Mexico, DF 04510 (Mexico); Lopez, G.P. [Department of Chemical and Nuclear Engineering, Center for Biomedical Engineering, University of New Mexico, Albuquerque, NM 87131 (United States)

    2007-11-15

    Changes in poly(ethylene terephthalate) subjected to electron beam irradiation at doses up to 15 MGy and dose rate of 1.65 MGy/h, were investigated by differential scanning calorimetry, molecular weight measurement, X-ray photoelectron spectroscopy, and scanning electron microscopy. Irradiated samples showed a decrease of molecular weight with a minimum at 5 MGy, which is attributed to chain scission of the macromolecules and then an increase at further doses due to branching and some degradation effect. Irradiation in air is not an important factor because the high dose rate of irradiation inhibits oxygen diffusion in the samples.

  7. Chemical Modification of Silk Fibers with Ethylene Glycol Dimethacrylate

    Institute of Scientific and Technical Information of China (English)

    CHEN Guo-qiang; ZHOU Xiang

    2002-01-01

    Silk fibers have been grafted with ethylene glycol dimethacrylate (EGDMA) and characteristics of the grafted silk fibers were analyzed in relation to the graft yield on the basis of the tensile properties, dyeing behaviour, durability during laundering and solubility of the specimen in NaOH solution. The amount of the acid dye absorbed by the fibers decreased with increasing graft yield, while the value of rating for washing fastness on silk fibers was almost unchanged by the graft treatment. The breaking loads of the fiber were almost unchanged whereas rigidity of the fibers increased after graft treatment. Graft treatment enhanced silk fiber durability during laundering and in NaOH solution.

  8. Study on the Relationship Between Sex Differentiation and Ethylene in Ramie

    Institute of Scientific and Technical Information of China (English)

    XING Hu-cheng; SHE Wei; LUO Zhong-qin; QIN Zhan-jun; JIE Yu-cheng

    2009-01-01

    To explore the role of ethylene in sexual determination in ramie,the ethylene release rates in ramie stem apex of different sex,bud of the same node in female and hermaphrodite ramie in the second crop,and single inflorescence of different sex in hermaphrodite ramie were measured by gas chromatography.Effects of two ethylene inhibitors on sex expression in ramie were investigated.The ethylene release rate of stem apex was higher in the second crop or female ramie than that in the third crop or hermaphrodite ramie during growth.Although ethylene release rates between lower nodes and higher nodes were little different,it was lower in the middle nodes in hermaphrodite ramie.The ethylene release rates were higher in the higher nodes of female ramie at the second crop.At the third crop,the ethylene release rates were higher in lower nodes,lower in middle nodes and then highest in higher nodes in female ramie.However,an opposite ethylene release pattern was observed in hermaphrodite ramie.The ethylene release rate was higher in female flower than male flower and mixed inflorescence in hermaphrodite ramie.The male flower could be distinctly induced by AVG(aminooethoxyvinylglycine).The node of the first male flower,percentage of female flowers and ratio of female flowers to male in ramie were evidently depressed by AVG in contrast to water.The percentage of mixed male and female flowers was also increased and the percentage of female flower decreased by spraying AgNO3.There was a close relationship between sexual differentiation and ethylene release rate in ramie.The female ramie could be induced by high ethylene release rate.The female flower could be inhibited by AVG and AgNO3.AVG at a concentration of 300 mg L-1 was most effective.

  9. Reducing ethylene levels along the food supply chain: a key to reducing food waste?

    Science.gov (United States)

    Blanke, Michael M

    2014-09-01

    Excessive waste along the food supply chain of 71 (UK, Netherlands) to 82 (Germany) kg per head per year sparked widespread criticism of the agricultural food business and provides a great challenge and task for all its players and stakeholders. Origins of this food waste include private households, restaurants and canteens, as well as supermarkets, and indicate that 59-65% of this food waste can be avoided. Since ∼50% of the food waste is fruit and vegetables, monitoring and control of their natural ripening gas - ethylene - is suggested here as one possible key to reducing food waste. Ethylene accelerates ripening of climacteric fruits, and accumulation of ethylene in the supply chain can lead to fruit decay and waste. While ethylene was determined using a stationary gas chromatograph with gas cylinders, the new generation of portable sensor-based instruments now enables continuous in situ determination of ethylene along the food chain, a prerequisite to managing and maintaining the quality and ripeness of fruits and identifying hot spots of ethylene accumulation along the supply chain. Ethylene levels were measured in a first trial, along the supply chain of apple fruit from harvest to the consumer, and ranged from 10 ppb in the CA fruit store with an ethylene scrubber, 70 ppb in the fruit bin, to 500 ppb on the sorting belt in the grading facility, to ppm levels in perforated plastic bags of apples. This paper also takes into account exogenous ethylene originating from sources other than the fruit itself. Countermeasures are discussed, such as the potential of breeding for low-ethylene fruit, applications of ethylene inhibitors (e.g. 1-MCP) and absorber strips (e.g. 'It's Fresh', Ryan'), packages (e.g. 'Peakfresh'), both at the wholesale and retail level, vents and cooling for the supply chain, sale of class II produce ('Wunderlinge'), collection (rather than waste) of produce on the 'sell by' date ('Die Tafel') and whole crop purchase (WCP) to aid reducing

  10. Effects of ethylene on the kinetics of curvature and auxin redistribution in gravistimulated roots of Zea mays

    Science.gov (United States)

    Lee, J. S.; Evans, M. L.

    1990-01-01

    We tested the involvement of ethylene in maize (Zea mays L.) root gravitropism by measuring the kinetics of curvature and lateral auxin movement in roots treated with ethylene, inhibitors of ethylene synthesis, or inhibitors of ethylene action. In the presence of ethylene the latent period of gravitropic curvature appeared to be increased somewhat. However, ethylene-treated roots continued to curve after control roots had reached their final angle of curvature. Consequently, maximum curvature in the presence of ethylene was much greater in ethylene-treated roots than in controls. Inhibitors of ethylene biosynthesis or action had effects on the kinetics of curvature opposite to that of ethylene, i.e. the latent period appeared to be shortened somewhat while total curvature was reduced relative to that of controls. Label from applied 3H-indole-3-acetic acid was preferentially transported toward the lower side of stimulated roots. In parallel with effects on curvature, ethylene treatment delayed the development of gravity-induced asymmetric auxin movement across the root but extended its duration once initiated. The auxin transport inhibitor, 1-N-naphthylphthalamic acid reduced both gravitropic curvature and the effect of ethylene on curvature. Since neither ethylene nor inhibitors of ethylene biosynthesis or action prevented curvature, we conclude that ethylene does not mediate the primary differential growth response causing curvature. Because ethylene affects curvature and auxin transport in parallel, we suggest that ethylene modifies curvature by affecting gravity-induced lateral transport of auxin, perhaps by interfering with adaptation of the auxin transport system to the gravistimulus.

  11. Overexpression of ARGOS Genes Modifies Plant Sensitivity to Ethylene, Leading to Improved Drought Tolerance in Both Arabidopsis and Maize.

    Science.gov (United States)

    Shi, Jinrui; Habben, Jeffrey E; Archibald, Rayeann L; Drummond, Bruce J; Chamberlin, Mark A; Williams, Robert W; Lafitte, H Renee; Weers, Ben P

    2015-09-01

    Lack of sufficient water is a major limiting factor to crop production worldwide, and the development of drought-tolerant germplasm is needed to improve crop productivity. The phytohormone ethylene modulates plant growth and development as well as plant response to abiotic stress. Recent research has shown that modifying ethylene biosynthesis and signaling can enhance plant drought tolerance. Here, we report novel negative regulators of ethylene signal transduction in Arabidopsis (Arabidopsis thaliana) and maize (Zea mays). These regulators are encoded by the ARGOS gene family. In Arabidopsis, overexpression of maize ARGOS1 (ZmARGOS1), ZmARGOS8, Arabidopsis ARGOS homolog ORGAN SIZE RELATED1 (AtOSR1), and AtOSR2 reduced plant sensitivity to ethylene, leading to enhanced drought tolerance. RNA profiling and genetic analysis suggested that the ZmARGOS1 transgene acts between an ethylene receptor and CONSTITUTIVE TRIPLE RESPONSE1 in the ethylene signaling pathway, affecting ethylene perception or the early stages of ethylene signaling. Overexpressed ZmARGOS1 is localized to the endoplasmic reticulum and Golgi membrane, where the ethylene receptors and the ethylene signaling protein ETHYLENE-INSENSITIVE2 and REVERSION-TO-ETHYLENE SENSITIVITY1 reside. In transgenic maize plants, overexpression of ARGOS genes also reduces ethylene sensitivity. Moreover, field testing showed that UBIQUITIN1:ZmARGOS8 maize events had a greater grain yield than nontransgenic controls under both drought stress and well-watered conditions.

  12. Active packaging using ethylene absorber to extend shelf-life

    Energy Technology Data Exchange (ETDEWEB)

    Ponce, Patricia; Carbonari, Guilherme L.R.; Lugao, Ademar B. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)], e-mail: patponce@iq.usp.br, e-mail: guilacaz@uol.com.br, e-mail: ablugao@ipen.br

    2009-07-01

    Ethylene gas is a plant hormone which is produced by fruits and vegetables during ripening and it is also found in the environment. It plays an essential role in normal ripening, but excessive exposure can radically reduce the shelf-life of the product, in some cases inducing undesirable reactions such as development of bitter flavors and loss of chlorophyll (yellowing of greens). The objectives of our work were: to test an active packaging of polyvinyl alcohol (PVA) for apple stored; to test the effect of ethylene absorber agent, impregnated in plastic film, to reduce decay of fresh apple; to study the influence of radiation on the barrier properties, mechanical properties and biodegradability of PVA films. This study evaluated the effect of coating produced from PVA and polyol (glycerol and sorbitol) as plasticizer on apple conservation (75 deg F (24 deg C); 70%RH). The coated product was analyzed for mass loss, color alterations and fungi. The PVA films were produced by casting process (dehydration of a filmogenic solution on Petriplastic dishes) and were irradiated at low doses of 2, 5 and 10 kGy, commonly used in food irradiation. The resulting films were transparent and homogeneous. The active packaged fruits presented higher acceptance, lower microbiological growth, less alterations in acidity, lower weight loss rate during the storage time and an extended shelf-life as compared to the control fruits (without plastic films). (author)

  13. Issues in assessing the carcinogenic hazards of ethylene oxide.

    Science.gov (United States)

    Austin, S G; Sielken, R L

    1988-03-01

    Characterization of the health risks associated with occupational and environmental exposure to ethylene oxide (a gaseous sterilization agent and chemical building block) is made difficult by the limited dose-response information contained in the few published epidemiologic studies available, and the absence of toxicologic data for chronic exposures in species other than the rat. Federal regulatory agencies have relied heavily on conventional quantitative risk assessment techniques in setting revised occupational exposure standards for ethylene oxide. This paper indicates the variability in risk assessment results that can be obtained using the multistage dose-response model and a single animal study depending on the method used to characterize risk, the health endpoint selected, the use of confidence intervals, and the method used to equate animal and human exposure levels. Selection of the most pessimistic options available in each of these four areas is shown to result in a virtually safe dose being characterized as 0.005 ppb, whereas other reasonable assumptions yield a safe dose estimate of 1.3 ppm.

  14. Micropatterning of poly(ethylene glycol) diacrylate hydrogels.

    Science.gov (United States)

    Ali, Saniya; Cuchiara, Maude L; West, Jennifer L

    2014-01-01

    This protocol describes the techniques to synthesize and fabricate micropatterned poly(ethylene glycol) diacrylate-based hydrogels that can be used as substrates in cellular studies and tissue engineering scaffolds. These materials provide an essentially bioinert background material due to the very low protein adsorption characteristics of poly(ethylene glycol), but the materials can be modified with covalently grafted peptides, proteins, or other biomolecules of interest to impart specific biofunctionality to the material. Further, it is possible to use micropatterning technologies to control the localization of such covalent grafting of biomolecules to the hydrogel materials, thus spatially controlling the cell-material interactions. This protocol presents a relatively simple approach for mask-based photolithographic patterning, generally best suited for patterning the surface of hydrogel materials for 2D cell studies. A more sophisticated technique, two-photon laser scanning lithography, is also presented. This technique allows free-form, 3D micropatterning in hydrogels. Copyright © 2014 Elsevier Inc. All rights reserved.

  15. Effects of ethylene on root elongation in barley and rice

    Energy Technology Data Exchange (ETDEWEB)

    John, A.; Hall, M.A.; Crossett, R.N.

    1972-01-01

    Experiments were performed to determine the effects of rice and barley to growth inhibition by ethylene. The mechanism of growth inhibition was investigated at the cellular level and a detailed comparison was made between the responses of the two species. The following measurements were made on intact plants in short (up to 200 minutes), medium (up to 3 days) or long (up to 10 days) experiments: the rate of extension growth of main root axes; the final cell length and number of elongating cells produced; and the extensibility of the apical growing region. Results indicate that the effects of ethylene on the elongation of roots of rice and barley plants are different. In barley there is a rapid inhibition of root extension which persists with prolonged exposure to the gas but with little effect on the production of growing cells. However, rice roots exhibit no rapid growth inhibition response, but a reduction does occur after prolonged exposure. Low concentrations promote extension rice roots. The inhibition of root growth is reflected in a reduced extensibility of the apical growing region.

  16. Ethylene Polymerization with Palygorskite Supported Nickel-Diimine Catalyst

    Institute of Scientific and Technical Information of China (English)

    严小伟; 王靖贷; 阳永荣; 张雷

    2005-01-01

    A nickel-diimine catalyst IN, N′-bis(2,6-diisopropylphenyl)-1,4-diaza-2,3-dimethyl-1, 3-butadiene nickel dibromide, DMN] was supported on palygorskite clay for ethylene slurry polymerization. The effect of supporting methods on the catalyst impregnation was studied and compared. Pretreatment of the support with methylaluminoxane (MAO) followed by DMN impregnation gave higher catalyst loading and catalytic activity than the direct impregnation of DMN. Catalyst activity as high as 5.42 × 105 g PE·molNi-l·h-1 was achieved at ethylene pressure of 6.87 × 105 Pa and polymerization temperature of 20℃ In particular, the morphological change of the support during MAO treatment was characterized and analyzed. It was found that nano-fiber clusters formed during the support pretreatment, which increased the surface area of the support and favored the impregnation of the catalyst. The investigation of polymerization behavior of supported catalyst revealed that the polymerization rate could be kept at a relatively high level for a long time, different from the homogeneous catalyst. By analyzing the SEM photographs of the polymer produced by the supported catalyst, the morphological evolution of polymer particles was preliminarily studied.

  17. Crystallization Behavior of Copolymer Poly (ethylene terephthalate/isophthalate) (IPET)

    Institute of Scientific and Technical Information of China (English)

    顾书英; 肖茹; 顾利霞

    2001-01-01

    The non-isothermal crystallization kinetics, isothermal crystallization and the morphology of crystals of the copolymer poly (ethylene terephthalate/ isophthalate )(IPET) were studied by DSC and polarized-light microscopy in this paper. DSC results indicate that the glass transition temperature Tg of IPET is slightly lower than that of poly(ethylene terephthalate) (PET), but the melting temperature Tm and the crystallization temperature Tc of PET and IPET have much difference.The difference of Tc between PET and IPET2 is about 7℃, and the difference of Tm between PET and IPET2 is about 16℃. From the kinetics analysis of the crystallization, the crystallization mechanism of all samples is of three-dimension spherulitic growth from instantaneous nuclei and the incorporation of isophthalate (IPA) decreases the crystallization rate of IPET greatly. The isothermal results indicate that the morphologies of PET and IPET crystals are all spherulite, which is in conformity to the results of nonisothermal dynamic crystallization. At the same time,the spherulite of IPET grows slower and has longer incubation time than the spherulite of PET under the same crystallization condition.

  18. Ethylene, 1-methylcyclopropene and silver thiosulfate on the post-production of ornamental pepper

    Directory of Open Access Journals (Sweden)

    Paula Cristina Carvalho Lima

    Full Text Available ABSTRACT: Species from Capsicum genus are used for different purposes and in more recent years as ornamental potted plant. Despite the increased commercial importance, there are only a few studies on the environmental factors affecting the post-production shelf life of these ornamental plants. The presence of ethylene induces various responses on potted peppers, reducing the shelf life of sensitive cultivars. This study aimed to evaluate the effects of ethylene and the inhibitors of ethylene action, 1-methylcyclopropene (1-MCP and silver thiosulfate (STS on the shelf life of potted 'Calypso' and 'MG 302' peppers. Cultivar 'MG 302' showed intermediate sensitivity to ethylene action, while the cultivar 'Calypso' showed complete abscission of leaves when exposed to ethylene. In both cultivars, treatment with STS + Ethylene presented symptoms of phytotoxicity in plants, while treatment with 1-MCP + Ethylene was effective in delaying senescence and abscission for the cultivar 'MG 302', while cultivar 'Calypso' showed abscission similar to control plants. Plants treated with STS showed the longest durability when compared to the other treatments, about six days for 'Calypso' and 18 days for 'MG 302'. Nevertheless, plants treated with 1-MCP also exhibited good shelf life, about six days for 'Calypso' and nine days for the 'MG 302'. Although the treatment with STS was more efficient on the plants shelf life, did not completely block the action of ethylene and exhibited some phytotoxicity, while the treatment with 1-MCP had good efficiency without inducing any toxicity.

  19. The relation between in vivo ethylene production and oxygen partial pressure

    NARCIS (Netherlands)

    Sanders, M.G.; Wild, de H.P.J.

    2003-01-01

    Modelling in vivo ethylene production rate in relation to O2 partial pressure was used to improve understanding of enzyme kinetics of 1-aminocyclopropane-1-carboxylate oxidase (ACC oxidase). Tomato fruit were stored in an extensive range of O2 partial pressures at 8, 13 and 18 °C. Ethylene

  20. 40 CFR 721.3800 - Formaldehyde, condensated polyoxyethylene fatty acid, ester with styrenated phenol, ethylene...

    Science.gov (United States)

    2010-07-01

    ... polyoxyethylene fatty acid, ester with styrenated phenol, ethylene oxide adduct. 721.3800 Section 721.3800... Formaldehyde, condensated polyoxyethylene fatty acid, ester with styrenated phenol, ethylene oxide adduct. (a... generically as formaldehyde, condensated polyoxyethylene fatty acid, ester with styrenated phenol,...

  1. 40 CFR 721.3680 - Ethylene oxide adduct of fatty acid ester with pentaerythritol.

    Science.gov (United States)

    2010-07-01

    ... ester with pentaerythritol. 721.3680 Section 721.3680 Protection of Environment ENVIRONMENTAL PROTECTION... New Uses for Specific Chemical Substances § 721.3680 Ethylene oxide adduct of fatty acid ester with... identified generically as ethylene oxide adduct of fatty acid ester with pentaerythritol (PMN P-91-442)...

  2. Regulating the ethylene response of a plant by modulation of F-box proteins

    Science.gov (United States)

    Guo, Hongwei [Beijing, CN; Ecker, Joseph R [Carlsbad, CA

    2014-01-07

    The relationship between F-box proteins and proteins invovled in the ethylene response in plants is described. In particular, F-box proteins may bind to proteins involved in the ethylene response and target them for degradation by the ubiquitin/proteasome pathway. The transcription factor EIN3 is a key transcription factor mediating ethylne-regulated gene expression and morphological responses. EIN3 is degraded through a ubiquitin/proteasome pathway mediated by F-box proteins EBF1 and EBF2. The link between F-box proteins and the ethylene response is a key step in modulating or regulating the response of a plant to ethylene. Described herein are transgenic plants having an altered sensitivity to ethylene, and methods for making transgenic plant haing an althered sensitivity to ethylene by modulating the level of activity of F-box proteins. Methods of altering the ethylene response in a plant by modulating the activity or expression of an F-box protein are described. Also described are methods of identifying compounds that modulate the ethylene response in plants by modulating the level of F-box protein expression or activity.

  3. The role of the embryo and ethylene in avocado fruit mesocarp discoloration.

    Science.gov (United States)

    Hershkovitz, Vera; Friedman, Haya; Goldschmidt, Eliezer E; Pesis, Edna

    2009-01-01

    Chilling injury (CI) symptoms in avocado (Persea americana Mill.) fruit, expressed as mesocarp discoloration, were found to be associated with embryo growth and ethylene production during cold storage. In cvs Ettinger and Arad most mesocarp discoloration was located close to the base of the seed and was induced by ethylene treatment in seeded avocado fruit. However, ethylene did not increase mesocarp discoloration in seedless fruit stored at 5 degrees C. Application of ethylene to whole fruit induced embryo development inside the seed. It also induced seedling elongation when seeds were imbibed separately. Persea americana ethylene receptor (PaETR) gene expression and polyphenol oxidase activity were highest close to the base of the seed and decreased gradually toward the blossom end. By contrast, expressions of PaETR transcript and polyphenol oxidase activity in seedless avocado fruit were similar throughout the pulp at the base of the fruit. Application of the ethylene inhibitor, 1-methylcyclopropene, decreased mesocarp browning, embryo development, seedling growth, and ion leakage, and down-regulated polyphenol oxidase activity. The results demonstrate that ethylene-mediated embryo growth in whole fruit is involved in the mesocarp response to ethylene perception and the development of CI disorders.

  4. Ethylene Epoxidation with Nitrous Oxide over Fe-BTC Metal-Organic Frameworks: A DFT Study.

    Science.gov (United States)

    Maihom, Thana; Choomwattana, Saowapak; Wannakao, Sippakorn; Probst, Michael; Limtrakul, Jumras

    2016-11-04

    The epoxidation of ethylene with N2 O over the metal-organic framework Fe-BTC (BTC=1,3,5-benzentricarboxylate) is investigated by means of density functional calculations. Two reaction paths for the production of ethylene oxide or acetaldehyde are systematically considered in order to assess the efficiency of Fe-BTC for the selective formation of ethylene oxide. The reaction starts with the decomposition of N2 O to form an active surface oxygen atom on the Fe site of Fe-BTC, which subsequently reacts with an ethylene molecule to form an ethyleneoxy intermediate. This intermediate can then be selectively transformed either by 1,2-hydride shift into the undesired product acetaldehyde or into the desired product ethylene oxide by way of ring closure of the intermediate. The production of ethylene oxide requires an activation energy of 5.1 kcal mol(-1) , which is only about one-third of the activation energy of acetaldehyde formation (14.3 kcal mol(-1) ). The predicted reaction rate constants for the formation of ethylene oxide in the relevant temperature range are approximately 2-4 orders of magnitude higher than those for acetaldehyde. Altogether, the results suggest that Fe-BTC is a good candidate catalyst for the epoxidation of ethylene by molecular N2 O. © 2016 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. Platelet deposition studies on copolyether urethanes modified with poly(ethylene oxide)

    NARCIS (Netherlands)

    Brinkman, E.; Foot, A.; van der Does, L.; Bantjes, A.

    1990-01-01

    Pellethane ® 2363 80A films and tubings were chemically modified and the effect of these modifications on platelet deposition was studied. Grafting of high molecular weight poly(ethylene oxide) and graft polymerization of methoxy poly(ethylene glycol) 400 methacrylate resulted in surfaces with a

  6. Comprehensive Proteomics Analysis of Laticifer Latex Reveals New Insights into Ethylene Stimulation of Natural Rubber Production.

    Science.gov (United States)

    Wang, Xuchu; Wang, Dan; Sun, Yong; Yang, Qian; Chang, Lili; Wang, Limin; Meng, Xueru; Huang, Qixing; Jin, Xiang; Tong, Zheng

    2015-09-08

    Ethylene is a stimulant to increase natural rubber latex. After ethylene application, both fresh yield and dry matter of latex are substantially improved. Moreover, we found that ethylene improves the generation of small rubber particles. However, most genes involved in rubber biosynthesis are inhibited by exogenous ethylene. Therefore, we conducted a proteomics analysis of ethylene-stimulated rubber latex, and identified 287 abundant proteins as well as 143 ethylene responsive latex proteins (ERLPs) with mass spectrometry from the 2-DE and DIGE gels, respectively. In addition, more than 1,600 proteins, including 404 ERLPs, were identified by iTRAQ. Functional classification of ERLPs revealed that enzymes involved in post-translational modification, carbohydrate metabolism, hydrolase activity, and kinase activity were overrepresented. Some enzymes for rubber particle aggregation were inhibited to prolong latex flow, and thus finally improved latex production. Phosphoproteomics analysis identified 59 differential phosphoproteins; notably, specific isoforms of rubber elongation factor and small rubber particle protein that were phosphorylated mainly at serine residues. This post-translational modification and isoform-specific phosphorylation might be important for ethylene-stimulated latex production. These results not only deepen our understanding of the rubber latex proteome but also provide new insights into the use of ethylene to stimulate rubber latex production.

  7. Ethylene production associated with petal senescence in carnation flowers is induced irrespective of the gynoecium.

    Science.gov (United States)

    Ichimura, Kazuo; Niki, Tomoko

    2014-11-15

    To clarify whether climacteric-like increases in ethylene production of senescing petals are also induced in the absence of the gynoecium in cut carnation (Dianthus caryophyllus cv. Barbara) flowers, we compared ethylene production and expression of ethylene-biosynthesis genes in detached petals and in petals, which remained on flowers (attached petals). No significant difference in longevity was observed between the attached and detached petals when held in distilled water, and both showed the inward rolling typical of senescing flowers. Treatment with silver thiosulfate complex (STS), an ethylene inhibitor, similarly delayed senescence of attached and detached petals. Climacteric-like increases in ethylene production of petals and gynoecium started on the same day, with similar bursts in attached and detached petals. Transcript levels of DcACS1 and DcACO1 were very low at harvest and increased similarly during senescence in both petal groups. Removal of the gynoecium did not significantly delay wilting of attached petals. In flowers with the gynoecium removed, the petals produced most of the ethylene while production by the other floral organs was very low, suggesting that wound-induced ethylene is not the reason for the ineffectiveness of gynoecium-removal in inhibiting flower senescence. These results indicate that ethylene biosynthesis is induced in carnation petals irrespective of the gynoecium.

  8. Application of Exogenous Ethylene Inhibits Postharvest Peel Browning of ‘Huangguan’ Pear

    Science.gov (United States)

    Peel browning disorder has an enormous impact on the exterior quality of ‘Huangguan’ pear whereas the underlying mechanism is still unclear. In this study, the effect of exogenous ethylene on peel browning of pear fruits stored at 0' was evaluated. Results showed that ethylene effectively inhibited ...

  9. 40 CFR 61.65 - Emission standard for ethylene dichloride, vinyl chloride and polyvinyl chloride plants.

    Science.gov (United States)

    2010-07-01

    ... dichloride, vinyl chloride and polyvinyl chloride plants. 61.65 Section 61.65 Protection of Environment... AIR POLLUTANTS National Emission Standard for Vinyl Chloride § 61.65 Emission standard for ethylene dichloride, vinyl chloride and polyvinyl chloride plants. An owner or operator of an ethylene...

  10. Effect of precooling and ethylene absorbent on the quality of Dendrobium "Pompadour" flowers

    NARCIS (Netherlands)

    Ketsa, S.; Imsabai, W.; Doorn, van W.G.

    2005-01-01

    We studied the effect of precooling and the use of an ethylene absorbent (based on potassium permanganate) in the flower boxes, on the vase life of Dendrobium `Pompadour` flowers, after simulation of air shipment (3 days at 25°C). Precooling at 10°C (85-95%RH) for 60 minutes reduced ethylene product

  11. On the origin of reactivity of steam reforming of ethylene glycol on supported Ni catalysts.

    Science.gov (United States)

    Li, Shuirong; Zhang, Chengxi; Zhang, Peng; Wu, Gaowei; Ma, Xinbin; Gong, Jinlong

    2012-03-28

    This paper describes a strategy for producing hydrogen via steam reforming of ethylene glycol over supported nickel catalysts. Nickel plays a crucial role in conversion of ethylene glycol and production of hydrogen, while oxide supports affect product distribution of carbonaceous species. A plausible reaction pathway is proposed based on our results and the literature.

  12. Temperature-controlled phase-transfer catalysis for ethylene glycol production from cellulose.

    Science.gov (United States)

    Tai, Zhijun; Zhang, Junying; Wang, Aiqin; Zheng, Mingyuan; Zhang, Tao

    2012-07-18

    A temperature-controlled phase-transfer catalyst-tungsten acid, which in combination with a robust heterogeneous catalyst Ru/C shows a high activity and exceptional reusability for the one-pot conversion of cellulose to ethylene glycol. This binary system can be reused more than 20 times with ethylene glycol yield over 50%.

  13. Effect of precooling and ethylene absorbent on the quality of Dendrobium "Pompadour" flowers

    NARCIS (Netherlands)

    Ketsa, S.; Imsabai, W.; Doorn, van W.G.

    2005-01-01

    We studied the effect of precooling and the use of an ethylene absorbent (based on potassium permanganate) in the flower boxes, on the vase life of Dendrobium `Pompadour` flowers, after simulation of air shipment (3 days at 25°C). Precooling at 10°C (85-95%RH) for 60 minutes reduced ethylene product

  14. Preparation of Ethylene Glycol Monoethyl Ether Acetate Using a Tubular Reactor

    Institute of Scientific and Technical Information of China (English)

    蔡振云; 卢祖国; 李小波

    2003-01-01

    Ethylene glycol monoethyl ether acetate (EGEA), an excellent solvent, is prepared with ethylene oxide (EO) and ethyl acetate (EA) in a tubular reactor under suitable reaction condition. The single circulation yield can reach 81%. This technology is not only safe but also makes it possible to continuously produce EGEA in industry,with low content of high boiling point by-products.

  15. The role of the embryo and ethylene in avocado fruit mesocarp discoloration

    Science.gov (United States)

    Hershkovitz, Vera; Friedman, Haya; Goldschmidt, Eliezer E.; Pesis, Edna

    2009-01-01

    Chilling injury (CI) symptoms in avocado (Persea americana Mill.) fruit, expressed as mesocarp discoloration, were found to be associated with embryo growth and ethylene production during cold storage. In cvs Ettinger and Arad most mesocarp discoloration was located close to the base of the seed and was induced by ethylene treatment in seeded avocado fruit. However, ethylene did not increase mesocarp discoloration in seedless fruit stored at 5 °C. Application of ethylene to whole fruit induced embryo development inside the seed. It also induced seedling elongation when seeds were imbibed separately. Persea americana ethylene receptor (PaETR) gene expression and polyphenol oxidase activity were highest close to the base of the seed and decreased gradually toward the blossom end. By contrast, expressions of PaETR transcript and polyphenol oxidase activity in seedless avocado fruit were similar throughout the pulp at the base of the fruit. Application of the ethylene inhibitor, 1-methylcyclopropene, decreased mesocarp browning, embryo development, seedling growth, and ion leakage, and down-regulated polyphenol oxidase activity. The results demonstrate that ethylene-mediated embryo growth in whole fruit is involved in the mesocarp response to ethylene perception and the development of CI disorders. PMID:19196750

  16. Value of embolization of brain arteriovenous malformations with ethylene vinyl alcohol copolymer

    Institute of Scientific and Technical Information of China (English)

    YANG Xin-xin; SONG Lu; WU Na; LIU Zhen-guo

    2010-01-01

    @@ T° the Editor We are interested in a recent article "Embolization of brain arteriovenous malformations with ethylene vinyl alcohol copolymer: technical aspects" written by GAO et al.1 Ethylene vinyl alcohol copolymer (Onyx) is a novel liquid embolic material used to cure brain arteriovenous malformations. They performed the embolization on 115 patients and they found that the complications of the treatment are scarce.

  17. Interactions between ethylene, gibberellins, and brassinosteroids in the development of rhizobial and mycorrhizal symbioses of pea.

    Science.gov (United States)

    Foo, Eloise; McAdam, Erin L; Weller, James L; Reid, James B

    2016-04-01

    The regulation of arbuscular mycorrhizal development and nodulation involves complex interactions between the plant and its microbial symbionts. In this study, we use the recently identified ethylene-insensitive ein2 mutant in pea (Pisum sativum L.) to explore the role of ethylene in the development of these symbioses. We show that ethylene acts as a strong negative regulator of nodulation, confirming reports in other legumes. Minor changes in gibberellin1 and indole-3-acetic acid levels in ein2 roots appear insufficient to explain the differences in nodulation. Double mutants produced by crosses between ein2 and the severely gibberellin-deficient na and brassinosteroid-deficient lk mutants showed increased nodule numbers and reduced nodule spacing compared with the na and lk single mutants, but nodule numbers and spacing were typical of ein2 plants, suggesting that the reduced number of nodules innaandlkplants is largely due to the elevated ethylene levels previously reported in these mutants. We show that ethylene can also negatively regulate mycorrhizae development when ethylene levels are elevated above basal levels, consistent with a role for ethylene in reducing symbiotic development under stressful conditions. In contrast to the hormone interactions in nodulation, ein2 does not override the effect of lk or na on the development of arbuscular mycorrhizae, suggesting that brassinosteroids and gibberellins influence this process largely independently of ethylene.

  18. H2S synthetase AtD-CDes involves in ethylene and drought regulated stomatal movement

    Institute of Scientific and Technical Information of China (English)

    Lixia Hou; Dan Zhu; Qian Ma; Dandan Zhang; Xin Liu

    2016-01-01

    The endogenous hydrogen sulfide (H2S),as a new gasotransmitter,participates in many plant physiological processes.In this study,we found that both ethylene and drought strongly induced H2S synthetase AtD-CDes gene expression and enzymatic activity.H2S synthesis inhibitors restrained the ethylene and drought induced stomatal closure in Arabidopsis.The H2S synthetase mutant Atd-cdes was insensitive to ethylene and drought,and overexpression of AtD-CDes conferred the transgenic plants more sensitive to ethylene and drought.Sequence analysis of AtD-CDes promoter showed that it contained ethylene response cis element ERE,and abiotic stress responsive cis elements MBS,LTR,and ABRE.The AtDCDes promoter fused with GUS was transformed into Arabidopsis thaliana to get AtD-CDes promoter::GUS transgenic plants.When treated with ethylene and drought stress,the enzymatic activity of β-glucuronidase was higher in the leaves and stomata of transgenic Arabidopsis.Analyses of GUS activity from the transgenic plants harboring different fragments of the promoter shows that the key section of AtD-CDes promoter response to ethylene was from the-697 to-408 bp,and the key section response to drought stress was from-90 to-1 bp.These results suggested that the H2S produced from AtD-CDes may mediate ethylene and drought-induced stomatal movement.

  19. 21 CFR 872.3410 - Ethylene oxide homopolymer and/or carboxymethylcellulose sodium denture adhesive.

    Science.gov (United States)

    2010-04-01

    ... carboxymethylcellulose sodium denture adhesive. 872.3410 Section 872.3410 Food and Drugs FOOD AND DRUG ADMINISTRATION....3410 Ethylene oxide homopolymer and/or carboxymethylcellulose sodium denture adhesive. (a) Identification. An ethylene oxide homopolymer and/or carboxymethylcellulose sodium denture adhesive is a...

  20. Design of a process to manufacture ethylene from ethane by means of a shock wave reactor

    NARCIS (Netherlands)

    Van der Dussen, J.; Farrelly, A.; Kort, G.; Twigt, V.; Weng, H.

    2006-01-01

    The aim of this project was to evaluate the possibility of building an economically viable SWR-plant while conforming to predetermined constraints and criteria. Globally, 117-million t/a ethylene is produced. The plant designed produces 1 Mt/a ethylene. The feedstock available is provided from nei

  1. The NO to NO{sub 2} conversion by ethylene oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Marinov, N.M. [Lawrence Livermore National Lab., CA (United States); Steele, R.C.; Malte, P.C. [Washington Univ., Seattle, WA (United States). Dept. of Mechanical Engineering; Hori, M. [Takushoku Univ., Tokyo (Japan). Department of Mechanical System Engineering

    1994-05-13

    A well-stirred reactor experiment and chemical kinetic modeling effort were performed in order to study the effect of ethylene oxidation on the conversion of nitric oxide (NO) to nitrogen dioxide (NO{sub 2}). Parameters examined in this study were temperature (1003--1260K) and input hydrocarbon concentration (220--3270 ppmv wet). The stirred reactor residence time was maintained at {approximately}2 milliseconds. Kinetic calculations indicated the NO to NO{sub 2} conversion proceeded through the ``HO{sub 2} mechanism``, NO + HO{sub 2} {yields} NO{sub 2} + OH, and the majority of the conversion occurred within the well-stirred reactor. The chemical kinetic mechanism used to model the percent conversion of the NO to NO{sub 2}, C{sub 2}H{sub 4}, CH{sub 4}, CO and CO{sub 2} concentrations showed excellent agreement with the experimental data, thereby validating the ethylene oxidation mechanism. Reaction pathway analysis and logarithmic sensitivity analysis were combined to analyze the ethylene oxidation structure and HO{sub 2} production process. The analysis revealed the primary ethylene oxidation pathway has the potential to form two HO{sub 2} radicals per ethylene consumed, thus making the ethylene a significant agent in promoting conversion of NO to NO{sub 2}. The secondary ethylene oxidation pathway is a potent chain branching process which furthers ethylene consumption and HO{sub 2} production.

  2. Quantitative comparisons of genotoxic effects of atomic energy and fossil-fuelled energy. Rad-equivalences for ethylene, ethylene oxide and formaldehyde - consequences for decisions at Government level

    Energy Technology Data Exchange (ETDEWEB)

    Latarjet, R.; Averbeck, D.; Levy, S.; Poirier, V. (Section de Biologie, Institut Curie, Paris, France)

    1982-01-01

    Rad-equivalences have been determined on the basis of data on the genotoxic effects of low linear energy transfer ionizing radiation and of three chemical pollutants - ethylene, ethylene oxide and formaldehyde - emitted from energy-producing power plants. In the case of ethylene and its metabolite, ethylene oxide, the conditions were particularly favourable because the equivalences could be based on the induction of total mutations in the mouse, which is the same genetic end-point used for the assessment of radiation risks. Once established, the rad-equivalences were used (a) to extrapolate the rules adopted for radiation to each of these two compounds and (b) to make recommendations for exposed workers at 'hot spots' and for the general population. Measurements of ethylene in power plants and in the atmosphere of Paris have indicated that in most cases the measured values fall within the recommended values. However, pollution by ethylene oxide in cold sterilization units should be reduced. Rad-equivalences obtained for lethal effects, and for the induction of chromosome aberrations by formaldehyde in human cells in vitro, suggest that the maximum admissible concentrations are far too high in most countries and must be reconsidered. In France, the Ministry of Health is taking the rad-equivalences into consideration for the preparation of a law regulating pollution by ethylene and ethylene oxide - as a first step. These results show that rad-equivalences can be used for risk assessments of genotoxic effects from power plants and that decisions can be made by extrapolating the rules adopted for radiation protection to some chemical mutagens, when certain strict conditions are fulfilled.

  3. Mechanical Characterization of Hybrid Vesicles Based on Linear Poly(Dimethylsiloxane-b-Ethylene Oxide) and Poly(Butadiene-b-Ethylene Oxide) Block Copolymers

    OpenAIRE

    2016-01-01

    Poly(dimethylsiloxane-ethylene oxide) (PDMS-PEO) and poly(butadiene-b-ethylene oxide) (PBd-PEO) are two block copolymers which separately form vesicles with disparate membrane permeabilities and fluidities. Thus, hybrid vesicles formed from both PDMS-PEO and PBd-PEO may ultimately allow for systematic, application-specific tuning of vesicle membrane fluidity and permeability. However, given the relatively low strength previously noted for comb-type PDMS-PEO vesicles, the mechanical robustness...

  4. Studies on the Reaction Mechanism of CPP and the Factors Affecting the Yields of Ethylene and Propylene

    Institute of Scientific and Technical Information of China (English)

    HouDianguo; WangXieqing; 等

    2002-01-01

    The reaction mechanisms of Catalytic Pyrolysis Process and the ethylene and propylene forma-tion reaction are analyzed,and ethylene and propylene are produced through both the free radical reac-tion and carbenium ion reaction.The factors affecting the yields of ethylene and propylene are discussed.The results showed that greater yields of ethylene and propylene can be obtained on ZSM-5 catalysts rather than USY and REY catalysts,and the modified ZSM-5 could improve the ethylene yield.A higher temperature is favorable for enhancement of the free radical reaction as opposed to carbenium ion reaction,and change in temperature can adjust the ratio of ethylene and propylene production.A higher steam amount could produce more ethylene and propylene and less coke,and lowering the catalyst/oil ratio is favorable for producing ethylene.

  5. Studies on the Reaction Mechanism of CPP and the Factors Affecting the Yields of Ethylene and Propylene

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The reaction mechanisms of Catalytic Pyrolysis Process and the ethylene and propylene forma-tion reaction are analyzed, and ethylene and propylene are produced through both the free radical reac-tion and carbenium ion reaction. The factors affecting the yields of ethylene and propylene are discussed.The results showed that greater yields of ethylene and propylene can be obtained on ZSM-5 catalystsrather than USY and REY catalysts, and the modified ZSM-5 could improve the ethylene yield. A highertemperature is favorable for enhancement of the free radical reaction as opposed to carbenium ion reaction,and change in temperature can adjust the ratio of ethylene and propylene production. A higher steamamount could produce more ethylene and propylene and less coke, and lowering the catalyst/oil ratio isfavorable for producing ethylene.

  6. Th he effe ect of e ethylen ne on t frui transg t quali genic m ity melon ...

    African Journals Online (AJOL)

    SAM

    for sensitive flavor (Pech et al., 2008). The synthesis ...... treated with exogenous ethylene, a stimulation of the .... vitamin C retention of pulsed electric field processed orange juice in ... corolla senescence and decreases sensitivity to ethylene.

  7. Carcinogenicity and genotoxicity of ethylene oxide: new aspects and recent advances.

    Science.gov (United States)

    Thier, R; Bolt, H M

    2000-09-01

    Long-term inhalation studies in rodents have presented unequivocal evidence of experimental carcinogenicity of ethylene oxide, based on the formation of malignant tumors at multiple sites. However, despite a considerable body of epidemiological data only limited evidence has been obtained of its carcinogenicity in humans. Ethylene oxide is not only an important exogenous toxicant, but it is also formed from ethylene as a biological precursor. Ethylene is a normal body constituent; its endogenous formation is evidenced by exhalation in rats and in humans. Consequently, ethylene oxide must also be regarded as a physiological compound. The most abundant DNA adduct of ethylene oxide is 7-(2-hydroxyethyl)guanine (HOEtG). Open questions are the nature and role of tissue-specific factors in ethylene oxide carcinogenesis and the physiological and quantitative role of DNA repair mechanisms. The detection of remarkable individual differences in the susceptibility of humans has promoted research into genetic factors that influence the metabolism of ethylene oxide. With this background it appears that current PBPK models for trans-species extrapolation of ethylene oxide toxicity need to be refined further. For a cancer risk assessment at low levels of DNA damage, exposure-related adducts must be discussed in relation to background DNA damage as well as to inter- and intraindividual variability. In rats, subacute ethylene oxide exposures on the order of 1 ppm (1.83 mg/m3) cause DNA adduct levels (HOEtG) of the same magnitude as produced by endogenous ethylene oxide. Based on very recent studies the endogenous background levels of HOEtG in DNA of humans are comparable to those that are produced in rodents by repetitive exogenous ethylene oxide exposures of about 10 ppm (18.3 mg/m3). Experimentally, ethylene oxide has revealed only weak mutagenic effects in vivo, which are confined to higher doses. It has been concluded that long-term human occupational exposure to low airborne

  8. Reductive transformation and inhibitory effect of ethylene under methanogenic conditions in peat-soil

    DEFF Research Database (Denmark)

    Elsgaard, Lars

    2013-01-01

    Ethylene (C2H4), which is a potent gaseous plant hormone, has often been found to accumulate in anoxic soils where pathways of anaerobic C2H4 oxidation are so far unknown and other C2H4 transformation processes are uncommon. The present study shows that ethylene was reduced almost...... stoichiometrically (89–92%) to ethane (C2H6) in peat-soil microcosms incubated under methanogenic conditions. Methanogenesis started after a prolonged anoxic lag-phase (>29 weeks) where added ethylene prevailed despite the availability of nitrate (NO3−) as an alternative electron acceptor. Methanogenesis, as well...... as ethylene reduction to ethane, was inhibited by 90% at 1% oxygen. Likewise, methanogenesis and ethane formation was gradually inhibited (to a similar extent) by increasing ethylene concentrations above 0.2%; this inhibition eventually reached 90–95% at 2.2–4.5% C2H4. The present results extend the known...

  9. Compressed ethylene phase states and their importance for the production of low density polyethylene

    Directory of Open Access Journals (Sweden)

    Stoiljković Dragoslav

    2006-01-01

    Full Text Available In the last three decades the authors have published papers on the concept of the supra-molecular organization and the phase state of compressed ethylene gas and their effects on the mechanism and kinetics of free-radical ethylene polymerization. The effects on the macromolecular structure of low density polyethylene (LDPE were also explained. The importance of the phase state of compressed ethylene on the industrial process of LDPE production are presented in this paper: The start-up of polymerization, the peak in the polymerization rate curve, the stability of the reaction, the structure and properties of LDPE, the separation of unreacted ethylene and polyethylene and ethylene compression are discussed.

  10. Induction of alternative respiratory pathway involves nitric oxide, hydrogen peroxide and ethylene under salt stress.

    Science.gov (United States)

    Wang, Huahua; Huang, Junjun; Bi, Yurong

    2010-12-01

    Alternative respiratory pathway (AP) plays an important role in plant thermogenesis, fruit ripening and responses to environmental stresses. AP may participate in the adaptation to salt stress since salt stress increased the activity of the AP. Recently, new evidence revealed that ethylene and hydrogen peroxide (H(2)O(2)) are involved in the salt-induced increase of the AP, which plays an important role in salt tolerance in Arabidopsis callus, and ethylene may be acting downstream of H(2)O(2). Recent observations also indicated both ethylene and nitric oxide (NO) act as signaling molecules in responses to salt stress, and ethylene may be a part of the downstream signal molecular in NO action. In this addendum, a hypothetical model for NO function in regulation of H(2)O(2)- and ethylene-mediated induction of AP under salt stress is presented.

  11. Reduction of energy usage in postharvest horticulture through management of ethylene.

    Science.gov (United States)

    Wills, Ron B H; Golding, John B

    2015-05-01

    Cool chain management is the preferred technology to extend the postharvest life of horticultural produce, but with rising energy costs and community pressure to reduce greenhouse gas emissions, there is a need to use less energy-intensive technologies. Minimising the level of ethylene around horticultural produce inhibits ripening and senescence and therefore has the potential to reduce the use of refrigeration. The long-distance transport of bananas within Australia and from Central America to Europe is used as a case study to show that the need for refrigeration could be reduced if the appropriate concentrations of ethylene were maintained around fruit during transit. Data are also presented to show a similar benefit of ethylene control with green beans, as well as another study showing that apples treated with the ethylene action inhibitor 1-methylcyclopropene could be stored at a higher temperature without loss of quality to the consumer. The range of technologies available to manage ethylene levels is discussed.

  12. Modeling and Optimization of Catalytic Dehydration of Ethanol to Ethylene Using Central Composite Design

    Institute of Scientific and Technical Information of China (English)

    KONG Haining; QI Ershi; LI Gang; HE Shuguang; ZHANG Xian

    2009-01-01

    The central composite design in the modeling and optimization of catalytic dehydration of ethanol to ethylene was performed to improve the ethylene yield. A total of 20 experiments at random were conducted to in-vestigate the effect of reaction temperature, Si/Al ratios of H-ZSM-5 catalyst and liquid hourly space velocity (LHSV)on the ethylene yield. The results show that the relationship between ethylene yield and the three signifi-cant independent variables can be approximated by a nonlinear polynomial model, with R-squared of 99.9% and adjusted R-squared of 99.8%. The maximal response for ethylene yield is 93.4% under the optimal condition of 328 ℃, Si/Al ratio 85, and LHSV 3.8 h-1.

  13. Design of smart oligo(ethylene glycol)-based biocompatible hybrid microgels loaded with magnetic nanoparticles.

    Science.gov (United States)

    Boularas, Mohamed; Gombart, Emilie; Tranchant, Jean-François; Billon, Laurent; Save, Maud

    2015-01-01

    This article reports a rational strategy for preparing smart oligo(ethylene glycol)-based hybrid microgels loaded with high content of homogeneously distributed preformed magnetic nanoparticles (NPs) (up to 33 wt%). The strategy is based on the synthesis of biocompatible multiresponsive microgels by precipitation copolymerization of di(ethylene glycol) methyl ether methacrylate, oligo(ethylene glycol) methyl ether methacrylate, methacrylic acid, and oligo(ethylene glycol)diac-rylate. An aqueous dispersion of preformed magnetic NPs is straightforwardly loaded into the microgels. Robust monodisperse thermoresponsive magnetic microgels are produced, exhibiting a constant value of the volume phase transition temperature whatever the NPs content. The homogeneous microstructure of the initial stimuli-responsive biocompatible microgels plays a crucial role for the design of unique well-defined ethylene glycol-based thermoresponsive hybrid microgels. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. Effect of acid density of HZSM-5 on the oligomerization of ethylene in FCC dry gas

    Institute of Scientific and Technical Information of China (English)

    Xue Ding; Shan Geng; Chunyi Li; Chaohe Yang; Guohui Wang

    2009-01-01

    The oligomerization of ethylene in FCC dry gas over HZSM-5 catalyst with different Si/Al2 ratios was studied. The effect of acid density of catalyst on the oligomerization of ethylene was discussed. By increasing the acid density of catalyst, ethylene conversion showed a linear increase, while the yields of olefins decreased when the acid density of catalyst exceeded 0.14 mmolNH3/g owing to a promotion of hydrogen transfer reaction. Through comparing the average distance between acid sites on catalyst with kinetic diameters of olefins, it was found that the dimerization of ethylene was not restrained by the sparse distribution of acid sites, while the hydrogen transfer reaction of C3 and C4 olefins was limited. On these bases, a conclusion is proposed that the dimerization of ethylene proceeded via Eley-Rideal mechanism, while the hydrogen transfer reaction of C3 and C4 olefins followed the Langmuir-Hinshelwood mechanism.

  15. Stress ethylene evolution of bean plants—a parameter indicating ozone pollution

    Science.gov (United States)

    Stan, Hans-Jürgen; Schicker, Sieglinde; Kassner, Helmut

    Bean plants treated with varying ozone concentrations for varying exposure times showed increased rates of ethylene production compared with controls. A standard method was worked out in which primary leaves of bean plants were encapsulated in 250 ml Erlenmeyer flasks after exposure. The amount of ethylene produced was determined by gas chromatography after about 24 h. The 'no effect level' of the bean plant was found to be 100 ppb ozone because there was no significant stress ethylene production even after 12 h fumigation. A treatment with 150 ppb ozone induced the beginning of stress ethylene production after about 8 h. With higher ozone concentrations shorter exposure times are necessary to induce a first response. Stress ethylene production correlates better with ozone concentration than with exposure time comparing the same products of concentration and time.

  16. A New Process for Synthesis of Dimethyl Carbonate from Ethylene Carbonate and Methanol without any Catalyst under Supercritical Conditions

    Institute of Scientific and Technical Information of China (English)

    Xiu Juan FENG; Xiao Gang LI; Ren HE; Hui ZHOU

    2005-01-01

    Dimethyl carbonate was synthesized by transesterification reaction between ethylene carbonate and methanol under supercritical conditions without any catalyst. Experimental results showed that the residence time and the molar ratio of methanol to ethylene carbonate all can affect the conversion of ethylene carbonate. When the molar ratio of methanol to ethylene carbonate was 8:1, 81.2 % conversion can be achieved at 9.0 MPa and 250℃ after 8 h.

  17. Mixed micelles of lipoic acid-chitosan-poly(ethylene glycol) and distearoylphosphatidylethanolamine-poly(ethylene glycol) for tumor delivery.

    Science.gov (United States)

    Elsaid, Zeeneh; Taylor, Kevin M G; Puri, Sanyogitta; Eberlein, Cath A; Al-Jamal, Khuloud; Bai, Jie; Klippstein, Rebecca; Wang, Julie Tzu-Wen; Forbes, Ben; Chana, Jasminder; Somavarapu, Satyanarayana

    2017-04-01

    Many chemotherapeutics suffer from poor aqueous solubility and tissue selectivity. Distearoylphosphatidylethanolamine-poly(ethylene glycol) (DSPE-PEG) micelles are a promising formulation strategy for the delivery of hydrophobic anticancer drugs. However, storage and in vivo instability restrict their use. The aim of this study was to prepare mixed micelles, containing a novel polymer, lipoic acid-chitosan-poly(ethylene glycol) (LACPEG), and DSPE-PEG, to overcome these limitations and potentially increase cancer cell internalisation. Drug-loaded micelles were prepared with a model tyrosine kinase inhibitor and characterized for size, surface charge, stability, morphology, drug entrapment efficiency, cell viability (A549 and PC-9 cell lines), in vivo biodistribution, ex vivo tumor accumulation and cellular internalisation. Micelles of size 30-130nm with entrapment efficiencies of 46-81% were prepared. LACPEG/DSPE-PEG mixed micelles showed greater interaction with the drug (condensing to half their size following entrapment), greater stability, and a safer profile in vitro compared to DSPE-PEG micelles. LACPEG/DSPE-PEG and DSPE-PEG micelles had similar entrapment efficiencies and in vivo tumor accumulation levels, but LACPEG/DSPE-PEG micelles showed higher tumor cell internalisation. Collectively, these findings suggest that LACPEG/DSPE-PEG mixed micelles provide a promising platform for tumor delivery of hydrophobic drugs. Copyright © 2017 Elsevier B.V. All rights reserved.

  18. Inhibition of ethylene response by 1-methylcyclopropene in potted ornamental pepper

    Directory of Open Access Journals (Sweden)

    Fernando Luiz Finger

    2015-06-01

    Full Text Available In the face of great potential of 1-MCP in blocking ethylene action, this study aimed to evaluate the efficacy of 1-MCP on ethylene action and extend the post-production of ornamental peppers Capsicum annuum potted plants. Ornamental pepper cultivar Calypso shows complete abscission of leaves when exposed to 10µL L-1 ethylene. By exposing plants to ethylene, significant drops on a, b and total chlorophyll were found at the end of the treatment. Nevertheless, no changes on leaf total carotenoid were observed after the treatment with ethylene. When the plants were treated with 1-methylcyclopropene (1-MCP, followed or not by treatment with ethylene, contents of a, b, total chlorophyll and carotenoid remained unchanged. Control plants showed no changes in chlorophylls or carotenoid contents after 48 hours from moving the pots from greenhouse to indoor conditions illuminated with white fluorescent light. The 1-MCP was able to prolong the post production shelf life, by inhibiting the abscission of leaves. Plants treated with 1-MCP, followed by ethylene had 38% accumulated leaf abscission, after 18 days of post production life, similar to control plants. After the same period, plants treated only with 1-MCP had 22% leaf abscission. The 1-MCP partially blocked ethylene and induced leaf abscission. Regardless which treatment was applied during post production life, there was a continuous decrease on leaf chlorophyll content beyond 18th day. Thus, 1-MCP was effective in preventing leaf abscission even in the presence of ethylene, avoiding deleterious effects of ethylene by blocking its receptor sites.

  19. Release of sunflower seed dormancy by cyanide: cross-talk with ethylene signalling pathway.

    Science.gov (United States)

    Oracz, Krystyna; El-Maarouf-Bouteau, Hayat; Bogatek, Renata; Corbineau, Françoise; Bailly, Christophe

    2008-01-01

    Freshly harvested sunflower (Helianthus annuus L.) seeds are considered to be dormant because they fail to germinate at relatively low temperatures (10 degrees C). This dormancy results mainly from an embryo dormancy and disappears during dry storage. Although endogenous ethylene is known to be involved in sunflower seed alleviation of dormancy, little attention had been paid to the possible role of cyanide, which is produced by the conversion of 1-aminocyclopropane 1-carboxylic acid to ethylene, in this process. The aims of this work were to investigate whether exogenous cyanide could improve the germination of dormant sunflower seeds and to elucidate its putative mechanisms of action. Naked dormant seeds became able to germinate at 10 degrees C when they were incubated in the presence of 1 mM gaseous cyanide. Other respiratory inhibitors showed that this effect did not result from an activation of the pentose phosphate pathway or the cyanide-insensitive pathway. Cyanide stimulated germination of dormant seeds in the presence of inhibitors of ethylene biosynthesis, but its improving effect required functional ethylene receptors. It did not significantly affect ethylene production and the expression of genes involved in ethylene biosynthesis or in the first steps of ethylene signalling pathway. However, the expression of the transcription factor Ethylene Response Factor 1 (ERF1) was markedly stimulated in the presence of gaseous cyanide. It is proposed that the mode of action of cyanide in sunflower seed dormancy alleviation does not involve ethylene production and that ERF1 is a common component of the ethylene and cyanide signalling pathways.

  20. Ethylene Inhibits Root Elongation during Alkaline Stress through AUXIN1 and Associated Changes in Auxin Accumulation.

    Science.gov (United States)

    Li, Juan; Xu, Heng-Hao; Liu, Wen-Cheng; Zhang, Xiao-Wei; Lu, Ying-Tang

    2015-08-01

    Soil alkalinity causes major reductions in yield and quality of crops worldwide. The plant root is the first organ sensing soil alkalinity, which results in shorter primary roots. However, the mechanism underlying alkaline stress-mediated inhibition of root elongation remains to be further elucidated. Here, we report that alkaline conditions inhibit primary root elongation of Arabidopsis (Arabidopsis thaliana) seedlings by reducing cell division potential in the meristem zones and that ethylene signaling affects this process. The ethylene perception antagonist silver (Ag(+)) alleviated the inhibition of root elongation by alkaline stress. Moreover, the ethylene signaling mutants ethylene response1-3 (etr1-3), ethylene insensitive2 (ein2), and ein3-1 showed less reduction in root length under alkaline conditions, indicating a reduced sensitivity to alkalinity. Ethylene biosynthesis also was found to play a role in alkaline stress-mediated root inhibition; the ethylene overproducer1-1 mutant, which overproduces ethylene because of increased stability of 1-AMINOCYCLOPROPANE-1-CARBOXYLIC ACID SYNTHASE5, was hypersensitive to alkaline stress. In addition, the ethylene biosynthesis inhibitor cobalt (Co(2+)) suppressed alkaline stress-mediated inhibition of root elongation. We further found that alkaline stress caused an increase in auxin levels by promoting expression of auxin biosynthesis-related genes, but the increase in auxin levels was reduced in the roots of the etr1-3 and ein3-1 mutants and in Ag(+)/Co(2+)-treated wild-type plants. Additional genetic and physiological data showed that AUXIN1 (AUX1) was involved in alkaline stress-mediated inhibition of root elongation. Taken together, our results reveal that ethylene modulates alkaline stress-mediated inhibition of root growth by increasing auxin accumulation by stimulating the expression of AUX1 and auxin biosynthesis-related genes.

  1. 78 FR 44117 - Notice of a Public Comment Period on the Draft IRIS Carcinogenicity Assessment for Ethylene Oxide

    Science.gov (United States)

    2013-07-23

    ... AGENCY Notice of a Public Comment Period on the Draft IRIS Carcinogenicity Assessment for Ethylene Oxide... Carcinogenicity of Ethylene Oxide'' (EPA/635/R-13/128a) and on the draft peer review charge questions. The draft... on the draft Evaluation of the Inhalation Carcinogenicity of Ethylene Oxide and on the draft peer...

  2. 40 CFR 63.63 - Deletion of ethylene glycol monobutyl ether from the list of hazardous air pollutants.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 9 2010-07-01 2010-07-01 false Deletion of ethylene glycol monobutyl... Quantity Designations, Source Category List § 63.63 Deletion of ethylene glycol monobutyl ether from the list of hazardous air pollutants. The substance ethylene glycol monobutyl ether (EGBE,2-Butoxyethanol...

  3. Simulation of 3D mesoscale structure formation in concentrated aqueous solution of the triblock polymer surfactants (ethylene oxide)(13)(propylene oxide)(30)(ethylene oxide)(13) and (propylene oxide)(19)(ethylene oxide)(33)(propylene oxide)(19). Application of dynamic mean-field density functional theory

    NARCIS (Netherlands)

    van Vlimmeren, BAC; Maurits, NM; Zvelindovsky, AV; Sevink, GJA; Fraaije, JGEM

    1999-01-01

    We simulate the microphase separation dynamics of aqueous solutions of the triblock polymer surfactants (ethylene oxide)(13)(propylene oxide)(30)(ethylene oxide)(13) and (propylene oxide)(19)(ethylene oxide)(33)(propylene oxide)(19) by a dynamic variant of mean-field density functional theory for

  4. Simulation of 3D mesoscale structure formation in concentrated aqueous solution of the triblock polymer surfactants (ethylene oxide)(13)(propylene oxide)(30)(ethylene oxide)(13) and (propylene oxide)(19)(ethylene oxide)(33)(propylene oxide)(19). Application of dynamic mean-field density functional theory

    NARCIS (Netherlands)

    van Vlimmeren, BAC; Maurits, NM; Zvelindovsky, AV; Sevink, GJA; Fraaije, JGEM

    1999-01-01

    We simulate the microphase separation dynamics of aqueous solutions of the triblock polymer surfactants (ethylene oxide)(13)(propylene oxide)(30)(ethylene oxide)(13) and (propylene oxide)(19)(ethylene oxide)(33)(propylene oxide)(19) by a dynamic variant of mean-field density functional theory for Ga

  5. Characteristics of Titanocene Catalyst Supported on Palygorskite for Ethylene Polymerization

    Institute of Scientific and Technical Information of China (English)

    Xiao Wei YAN; Jing Dai WANG; Yi Bing SHAN; Yong Rong YANG

    2006-01-01

    A series of heterogeneous catalysts with Cp2TiCl2 supported on palygorskite were prepared and evaluated by ethylene slurry polymerizations. The so-called direct supported catalyst, for which the pretreatment of palygorskite with MAO or Al(i-Bu)3 was not necessary,gave the highest activity among these supported catalysts and could be more robust than homogeneous Cp2TiCl2. With the direct supported catalyst, no significant activity loss was observed under low Al/Ti molar ratios (Al/Ti=300) and the decay of polymerization rate was slower when compared to the other supported catalysts. It was found that the surface Lewis acidity of palygorskite after thermal treatment played an important role in activation of metallocene compound and resulted in high catalyst activity.

  6. Ethylene glycol contamination effects on first surface aluminized mirrors

    Science.gov (United States)

    Dunlop, Patrick; Probst, Ronald G.; Evatt, Matthew; Reddell, Larry; Sprayberry, David

    2016-07-01

    The Dark Energy Spectroscopic Instrument (DESI) is under construction for installation on the Mayall 4 Meter telescope. The use of a liquid cooling system is proposed to maintain the DESI prime focus assembly temperature within ±1°C of ambient. Due to concerns of fluid deposition onto optical surfaces from possible leaks, systematic tests were performed of the effects on first surface aluminized mirrors of ethylene glycol and two other candidate coolants. Objective measurement of scattering and reflectivity was an important supplement to visual inspection. Rapid cleanup of a coolant spill followed by a hand wash of the mirror limited surface degradation to the equivalent of a few months of general environmental exposure. Prolonged exposure to corrosive coolants dissolved the aluminum, necesitating mirror recoating.

  7. Evaluation of the Carcinogenicity of Ethylene Oxide (2006 ...

    Science.gov (United States)

    EPA conducted a peer review and public comment of the scientific basis supporting the human health hazard and dose-response assessment of ethylene oxide (cancer) that when finalized will appear on the Integrated Risk Information System (IRIS) database. EPA is announcing a 30-day public comment period for this document. The release of this draft document is solely for the purpose of seeking public comment and for review by the EPA Science Advisory Board (SAB) via a meeting to be held later in 2006. The time and place of the SAB meeting will be announced in a separate Federal Register notice. This document has not been formally disseminated by EPA and does not represent, and should not be construed to represent, any Agency policy or determination. EPA will consider any public comments submitted in accordance with the requirements specified in the Notice of Public Comment Period when revising this draft document.

  8. Study of positive and negative plasma catalytic oxidation of ethylene.

    Science.gov (United States)

    Van Wesenbeeck, K; Hauchecorne, B; Lenaerts, S

    2017-06-01

    The effect of introducing a photocatalytically active coating inside a plasma unit is investigated. This technique combines the advantages of high product selectivity from catalysis and the fast start-up from plasma technology. In this study, a preselected TiO2 coating is applied on the collector electrode of a DC corona discharge unit as non-thermal plasma reactor, in order to study the oxidation of ethylene. For both positive and negative polarities an enhanced mineralization is observed while the formation of by-products drastically decreases. The plasma catalytic unit gave the best results when using negative polarity at a voltage of 15 kV. This shows the potential of plasma catalysis as indoor air purification technology.

  9. Ethylene tetrafluoroethylene nanofibers prepared by CO2 laser supersonic drawing

    Directory of Open Access Journals (Sweden)

    A. Suzuki

    2013-06-01

    Full Text Available Ethylene tetrafluoroethylene (ETFE nanofibers were prepared by carbon dioxide (CO2 laser irradiation of asspun ETFE fibers with four different melt flow rates (MFRs in a supersonic jet that was generated by blowing air into a vacuum chamber through the fiber injection orifice. The drawability and superstructure of fibers produced by CO2 laser supersonic drawing depend on the laser power, the chamber pressure, the fiber injection speed, and the MFR. Nanofibers obtained using a laser power of 20 W, a chamber pressure of 20 kPa, and an MFR of 308 g•10 min–1 had an average diameter of 0.303 µm and a degree of crystallinity of 54%.

  10. [Ethylene glycol and propylene glycol ethers - Reproductive and developmental toxicity].

    Science.gov (United States)

    Starek-Świechowicz, Beata; Starek, Andrzej

    2015-01-01

    Both ethylene and propylene glycol alkyl ethers (EGAEs and PGAEs, respectively) are widely used, mainly as solvents, in industrial and household products. Some EGAEs demonstrate gonadotoxic, embriotoxic, fetotoxic and teratogenic effects in both humans and experimental animals. Due to the noxious impact of these ethers on reproduction and development of organisms EGAEs are replaced for considerably less toxic PGAEs. The data on the mechanisms of testicular, embriotoxic, fetotoxic and teratogenic effects of EGAEs are presented in this paper. Our particular attention was focused on the metabolism of some EGAEs and their organ-specific toxicities, apoptosis of spermatocytes associated with changes in the expression of various genes that code for oxidative stress factors, protein kinases and nuclear hormone receptors.

  11. Rheological profile of boron nitride–ethylene glycol nanofluids

    Energy Technology Data Exchange (ETDEWEB)

    Żyła, Gaweł, E-mail: gzyla@prz.edu.pl [Department of Physics, Rzeszów University of Technology, Rzeszów (Poland); Witek, Adam; Gizowska, Magdalena [Department of Nanotechnology, Institute of Ceramics and Building Materials, Warsaw (Poland)

    2015-01-07

    The paper presents the complete rheological profile of boron nitride (BN)–ethylene glycol (EG) nanofluids. Nanofluids have been produced by two-step method on the basis of commercially available powder of plate-like grains of nanometrical thickness. Viscoelastic structure has been determined in oscillatory measurements at a constant frequency and temperature. Viscosity and flow curves for these materials have been measured. Studies have shown that the Carreau model can be used for the modeling of dynamic viscosity curves of the material. The samples were tested for the presence of thixotropy. The dependence of viscosity on temperature was also examined. The effect of temperature on the dynamic viscosity of BN-EG nanofluids can be modelled with the use of Vogel-Fulcher-Tammann expression.

  12. Synthesis of Propargyl-Terminated Heterobifunctional Poly(ethylene glycol

    Directory of Open Access Journals (Sweden)

    Wen Zhong

    2010-10-01

    Full Text Available Novel propargyl-ended heterobifunctional poly(ethylene glycol (PEG derivatives with hydroxyl, carboxyl, mercapto or hydrazide end groups were synthesized with simplicity yet high efficiency. PEG (Mw = 3500 Da with an α-hydroxyl group and an ω-carboxyl was used as the starting polymer. The carboxyl group of the bifunctional PEG was modified into a propargyl, then carboxyl, mercapto or hydrazide groups were introduced to the other end of the bifunctional PEG by modifying the bifunctional PEG’s hydroxyl group with succinic anhydride, cysteamide or tert-butyl carbazate, respectively. This method can be useful to the development of PEG-based bioconjugates for a variety of biomedical applications.

  13. Diffusivities and Viscosities of Poly(ethylene oxide) Oligomers †

    KAUST Repository

    Hong, Bingbing

    2010-10-14

    Diffusivities and viscosities of poly(ethylene oxide) (PEO) oligomer melts with 1 to 12 repeat units have been obtained from equilibrium molecular dynamics simulations using the TraPPE-UA force field. The simulations generated diffusion coefficients with high accuracy for all of the molar masses studied, but the statistical uncertainties in the viscosity calculations were significantly larger for longer chains. There is good agreement of the calculated viscosities and densities with available experimental data, and thus, the simulations can be used to bridge gaps in the data and for extrapolations with respect to chain length, temperature, and pressure. We explored the convergence characteristics of the Green-Kubo formulas for different chain lengths and propose minimal production times required for convergence of the transport properties. The chain-length dependence of the transport properties suggests that neither Rouse nor reptation models are applicable in the short-chain regime investigated. © 2010 American Chemical Society.

  14. Modification of ethylene-norbornene copolymer by Gamma irradiation

    Directory of Open Access Journals (Sweden)

    Kačarević-Popović Zorica M.

    2006-01-01

    Full Text Available The possibility of modifying polyethylene and many other polymers with high energy radiation has led to many useful applications. Due to their new combination of properties and the shortage of experimental data, the radiolysis of a new class of materials, cyclo-olefin copolymers (COC, polymerised from norbornene and ethylene using metallocene catalysts, is of great interest to the study of radiation chemistry and the physics of polymeric systems. Ethylenenorbornene copolymer, pristine and containing an antioxidant were subjected to gamma irradiation in the presence of air and in water. The irradiated copolymer was studied using IR and UV-vis spectrophotometric analysis. The radiation-induced changes in the molecular structure were correlated to changes in the glass transition temperature measured by the DSC method.

  15. Sulfonation of vulcanized ethylene-propylene-diene terpolymer membranes

    Energy Technology Data Exchange (ETDEWEB)

    Barroso-Bujans, F. [Instituto de Ciencia y Tecnologia de Polimeros, CSIC, Juan de la Cierva 3, 28006 Madrid (Spain)], E-mail: fbarroso@ictp.csic.es; Verdejo, R.; Lozano, A. [Instituto de Ciencia y Tecnologia de Polimeros, CSIC, Juan de la Cierva 3, 28006 Madrid (Spain); Fierro, J.L.G. [Instituto de Catalisis y Petroleoquimica, CSIC, Marie Curie 2, Cantoblanco, 28049 Madrid (Spain); Lopez-Manchado, M.A. [Instituto de Ciencia y Tecnologia de Polimeros, CSIC, Juan de la Cierva 3, 28006 Madrid (Spain)

    2008-10-15

    In the present work, sulfonation of previously vulcanized ethylene propylene diene terpolymer (EPDM) membranes was developed in a swelling solvent with acetyl sulfate. This procedure avoids the need to pre-dissolve the raw polymer. The reaction conditions were optimized in terms of solvent type, reaction time, acetyl sulfate concentration and film thickness to obtain the maximum degree of sulfonation of the polymer. The sulfonation procedure presented in this study yields a degree of sulfonation comparable to the chlorosulfonic acid procedure. Sulfonic acid groups were detected by X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy, and quantified by titrations. Proton conductivity and water uptake were measured by means of impedance spectroscopy and swelling measurements, respectively, and were correlated with the degree of sulfonation. Tensile strength and Young's modulus of sulfonated EPDM increased with the degree of sulfonation, while elongation at break remained constant. Thermal stability of the sulfonated EPDM was studied by simultaneous thermogravimetry-mass spectroscopy.

  16. Viscoelastic Properties of Fluorinated Ethylene-Propylene (FEP) Random Copolymers

    Science.gov (United States)

    Curtin, Megan; Wright, Benjamin; Ozisik, Rahmi

    Florinated ethylene-propylene (FEP) random copolymers contain tetrafluoroethylene (TFE) and hexafluoropropylene (HFP) repeat units. FEP is an excellent alternative to poly(tetrafluoroethylene), PTFE, which cannot be melt processed due to its high molecular weight and extensive crystallinity. On the other hand, FEP is a melt processible polymer and offers similar if not the same properties as PTFE. Many studies have been performed on FEP over the years, however, the properties of these polymers strongly depend on the HFP concentration and molecular weight (distribution). Just like PTFE, FEP cannot be dissolved in many solvents, therefore, obtaining molecular weight distribution of these polymers is not possible with commonly used methods. In the current study, we perform rheological analysis of various FEPs and obtain their molecular weight distributions by employing the Tuminello method. This material is based upon work supported by the National Science Foundation under Grant No. CMMI-1538730.

  17. Electron beam induced modification of poly(ethylene terephthalate) films

    Energy Technology Data Exchange (ETDEWEB)

    Vasiljeva, I.V. [Technology Center RADIANT, 10, Kurchatova Str., 194223 St. Petersburg (Russian Federation)]. E-mail: radiant@skylink.spb.ru; Mjakin, S.V. [Technology Center RADIANT, 10, Kurchatova Str., 194223 St. Petersburg (Russian Federation); Makarov, A.V. [St.-Petersburg State University of Cinema and Television, 13, ul. Pravdy, 191126 St. Petersburg (Russian Federation); Krasovsky, A.N. [St.-Petersburg State University of Cinema and Television, 13, ul. Pravdy, 191126 St. Petersburg (Russian Federation); Varlamov, A.V. [St.-Petersburg State University of Cinema and Television, 13, ul. Pravdy, 191126 St. Petersburg (Russian Federation)

    2006-10-15

    Electron beam processing of poly(ethylene terephthalate) (PET) films is found to promote significant changes in the melting heat, intrinsic viscosity and polymer film-liquid (water, isooctane and toluene) boundary surface tension. These properties are featured with several maximums depending on the absorbed dose and correlating with the modification of PET surface functionality. Studies using adsorption of acid-base indicators and IR-spectroscopy revealed that the increase of PET surface hydrophilicity is determined by the oxidation of methylene and methyne groups. Electron beam treatment of PET films on the surface of N-vinylpyrrolidone aqueous solution provided graft copolymerization with this comonomer at optimum process parameters (energy 700 keV, current 1 mA, absorbed dose 50 kGy)

  18. Ethylene, nitric oxide and haemoglobins in plant tolerance to flooding

    DEFF Research Database (Denmark)

    Mur, Luis A J; Gupta, Kapuganti J; Hebelstrup, Kim

    2015-01-01

    As much as 12% of the world's soils may suffer excess water so that flooding is a major limiting factor on crop production in many areas. Plants attempt to deal with submergence by forming root aerenchyma to facilitate oxygen diffusion from the shoot to the root, initiating a hyponastic response...... where petiole elongation facilitates access to atmospheric oxygen or initiating a bio-energetically conserving quiescence phase. Ethylene has well established roles in the initiation of programmed cell death (PCD) to form air-spaces in aerenchyma and in the hyponastic responses in petioles. The flooding...... response. NO is formed from the reduction of NO3/NO2 via several pathways, which are differentially utilized depending on the availability of O2. In fact, NO production and responses to flooding can be directly dependent on the nitrogen status of soil, which reflects local agricultural practice...

  19. Oxidative dehydrogenation of ethane to ethylene using vanadia based catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Qiao, Ailing; Kalevaru, V.N. [Univ. Rostock e.V., Rostock (Germany). Leibniz-Inst. fuer Katalyse; Humar, A.S.; Lingaiah, N.; Sai Prasad, P.S.; Martin, A. [Indian Institute of Chemical Technology, Hyderabad (India). Inorganic and Physical Chemistry Div.

    2011-07-01

    In this work, we describe the application of V{sub 2}O{sub 5}/Nb{sub 2}O{sub 5} catalysts for the oxidative dehydrogenation (ODH) of ethane to ethylene. A series of Nb{sub 2}O{sub 5} supported V{sub 2}O{sub 5} catalysts were prepared by impregnation technique. NH{sub 4}VO{sub 3} was used as a precursor for V{sub 2}O{sub 5}. The content of V{sub 2}O{sub 5} is varied in the range from 5 to 20 wt%. Catalytic tests were carried out in a fixed bed quartz reactor in the temperature range from 500 to 600 C. The conversion of ethane has been increased from ca. 20 to 35 % with increase in temperature from 500 to 600 C, while the yield of ethylene is increased from about 5 to 12 % only. CO and CO{sub 2} are the only major by-products of the reaction. The activity tests were performed at low O{sub 2} concentration in the feed and hence low conversions were achieved. Furthermore, the conversion of ethane is found to increase continuously with increase in V{sub 2}O{sub 5} loading while the yield of C{sub 2}H{sub 4} increased only up to 10wt% V{sub 2}O{sub 5} and then decreased. Results revealed that the catalytic activity and selectivity is found to depend on the V{sub 2}O{sub 5} loading. Among all, 10wt% V{sub 2}O{sub 5}/Nb{sub 2}O{sub 5} catalyst has displayed the superior performance. (orig.)

  20. Oxidative dehydrogenation of ethane to ethylene using vanadia based catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Qiao, Ailing; Kalevaru, V.N. [Univ. Rostock e.V., Rostock (Germany). Leibniz-Inst. fuer Katalyse; Humar, A.S.; Lingaiah, N.; Sai Prasad, P.S.; Martin, A. [Indian Institute of Chemical Technology, Hyderabad (India). Inorganic and Physical Chemistry Div.

    2011-07-01

    In this work, we describe the application of V{sub 2}O{sub 5}/Nb{sub 2}O{sub 5} catalysts for the oxidative dehydrogenation (ODH) of ethane to ethylene. A series of Nb{sub 2}O{sub 5} supported V{sub 2}O{sub 5} catalysts were prepared by impregnation technique. NH{sub 4}VO{sub 3} was used as a precursor for V{sub 2}O{sub 5}. The content of V{sub 2}O{sub 5} is varied in the range from 5 to 20 wt%. Catalytic tests were carried out in a fixed bed quartz reactor in the temperature range from 500 to 600 C. The conversion of ethane has been increased from ca. 20 to 35 % with increase in temperature from 500 to 600 C, while the yield of ethylene is increased from about 5 to 12 % only. CO and CO{sub 2} are the only major by-products of the reaction. The activity tests were performed at low O{sub 2} concentration in the feed and hence low conversions were achieved. Furthermore, the conversion of ethane is found to increase continuously with increase in V{sub 2}O{sub 5} loading while the yield of C{sub 2}H{sub 4} increased only up to 10wt% V{sub 2}O{sub 5} and then decreased. Results revealed that the catalytic activity and selectivity is found to depend on the V{sub 2}O{sub 5} loading. Among all, 10wt% V{sub 2}O{sub 5}/Nb{sub 2}O{sub 5} catalyst has displayed the superior performance. (orig.)

  1. Fabrication of poly(ethylene glycol) hydrogel microstructures using photolithography

    Science.gov (United States)

    Revzin, A.; Russell, R. J.; Yadavalli, V. K.; Koh, W. G.; Deister, C.; Hile, D. D.; Mellott, M. B.; Pishko, M. V.

    2001-01-01

    The fabrication of hydrogel microstructures based upon poly(ethylene glycol) diacrylates, dimethacrylates, and tetraacrylates patterned photolithographically on silicon or glass substrates is described. A silicon/silicon dioxide surface was treated with 3-(trichlorosilyl)propyl methacrylate to form a self-assembled monolayer (SAM) with pendant acrylate groups. The SAM presence on the surface was verified using ellipsometry and time-of-flight secondary ion mass spectrometry. A solution containing an acrylated or methacrylated poly(ethylene glycol) derivative and a photoinitiator (2,2-dimethoxy-2-phenylacetophenone) was spin-coated onto the treated substrate, exposed to 365 nm ultraviolet light through a photomask, and developed with either toluene, water, or supercritical CO2. As a result of this process, three-dimensional, cross-linked PEG hydrogel microstructures were immobilized on the surface. Diameters of cylindrical array members were varied from 600 to 7 micrometers by the use of different photomasks, while height varied from 3 to 12 micrometers, depending on the molecular weight of the PEG macromer. In the case of 7 micrometers diameter elements, as many as 400 elements were reproducibly generated in a 1 mm2 square pattern. The resultant hydrogel patterns were hydrated for as long as 3 weeks without delamination from the substrate. In addition, micropatterning of different molecular weights of PEG was demonstrated. Arrays of hydrogel disks containing an immobilized protein conjugated to a pH sensitive fluorophore were also prepared. The pH sensitivity of the gel-immobilized dye was similar to that in an aqueous buffer, and no leaching of the dye-labeled protein from the hydrogel microstructure was observed over a 1 week period. Changes in fluorescence were also observed for immobilized fluorophore labeled acetylcholine esterase upon the addition of acetyl acholine.

  2. Ethylene antagonizes salt-induced growth retardation and cell death process via transcriptional controlling of ethylene-, BAG- and senescence-associated genes in Arabidopsis

    Directory of Open Access Journals (Sweden)

    YaJie ePan

    2016-05-01

    Full Text Available The existing question whether ethylene is involved in the modulation of salt-induced cell death to mediate plant salt tolerance is important for understanding the salt tolerance mechanisms. Here, we employed Arabidopsis plants to study the possible role of ethylene in salt-induced growth inhibition and programmed cell death (PCD profiles. The root length, DNA ladder and cell death indicated by Evan’s blue detection were measured by compared to the control or salt-stressed seedlings. Secondly, the protoplasts isolated from plant leaves and dyed with Annexin V-FITC were subjected to flow cytometric (FCM assay. Our results showed that ethylene works effectively in seedling protoplasts, antagonizing salt-included root retardation and restraining cell death both in seedlings or protoplasts. Due to salinity, the entire or partial insensitivity of ethylene signaling resulted in an elevated levels of cell death in ein2-5 and ein3-1 plants and the event were amended in ctr1-1 plants after salt treatment. The subsequent experiment with exogenous ACC further corroborated that ethylene could modulate salt-induced PCD process actively. Plant Bcl-2-associated athanogene (BAG family genes are recently identified to play an extensive role in plant PCD processes ranging from growth, development to stress responses and even cell death. Our result showed that salinity alone significantly suppressed the transcripts of BAG6, BAG7 and addition of ACC in the saline solution could obviously re-activate BAG6 and BAG7 expressions, which might play a key role to inhibit the salt-induced cell death. In summary, our research implies that ethylene and salinity antagonistically control BAG family-, ethylene-, and senescence-related genes to alleviate the salt-induced cell death.

  3. Modification by Ethylene of the Cell Growth Pattern in Different Tissues of Etiolated Lupine Hypocotyls 1

    Science.gov (United States)

    Sánchez-Bravo, José; Ortuño, Ana M.; Pérez-Gilabert, Manuela; Acosta, Manuel; Sabater, Francisco

    1992-01-01

    The influence of ethylene on growth in etiolated lupine (Lupinus albus L.) hypocotyls was studied in ethephon-treated plants. Ethephon reduced the length and increased the diameter of hypocotyls. At the end of the hypocotyl growth period (14 days), the fresh weight was reduced by 53%, and the dry weight was reduced by 16%. Thus, ethylene reduced water uptake in the tissues to a greater extent than the incorporation of new materials. Light microscopic measurements showed that the thickness of tissues was stimulated by ethylene, the vascular cylinder and cortex exhibiting greater increases (55 and 45%, respectively) than pith (26%) or epidermis (12%). Ethephon modified the cell growth pattern, stimulating lateral cell expansion and cell wall thickness, while reducing cell elongation. The response to ethylene varied in the different tissues and was higher in cortex and pith cells than in the epidermis cells. The ethylene-induced cell expansion in the cortex varied according to the localization of cells in the tissue: the central and subepidermal layers showed little change, whereas the innermost layers exhibited the greatest increase. Electron microscopy revealed that ethylene increased both the rough endoplasmic reticulum and dictyosomes, suggesting that ethylene stimulated the secretion of cell wall materials. In untreated seedlings, the pattern of cell growth was similar in cells from the epidermis, cortex, and pith. The final cell size varied along the hypocotyl, the cells becoming shorter and broader the closer to the basal zones of the organ. ImagesFigure 1Figure 5 PMID:16668735

  4. Ethylene: Response of Fruit Dehiscence to CO2 and Reduced Pressure 1

    Science.gov (United States)

    Lipe, John A.; Morgan, Page W.

    1972-01-01

    These studies were conducted to determine whether ethylene serves as a natural regulator of fruit wall dehiscence, a major visible feature of ripening in some fruits. We employed treatments to inhibit ethylene action or remove ethylene and observed their effect on fruit dehiscence. CO2 (13%), a competitive inhibitor of ethylene action in many systems, readily delayed dehiscence of detached fruits of cotton (Gossypium hirsutum L.), pecan (Carya illinoensis [Wang.] K. Koch), and okra (Hibiscus esculentus L.). The CO2 effect was duplicated by placing fruits under reduced pressure (200 millimeters mercury), to promote the escape of ethylene from the tissue. Dehiscence of detached fruits of these species as well as attached cotton fruits was delayed. The delay of dehiscence of cotton and okra by both treatments was achieved with fruit harvested at intervals from shortly after anthesis until shortly before natural dehiscence. Pecan fruits would not dehisce until approximately 1 month before natural dehiscence, and during that time, CO2 and reduced pressure delayed dehiscence. CO2 and ethylene were competitive in their effects on cotton fruit dehiscence. All of the results are compatible with a hypothetical role of ethylene as a natural regulator of dehiscence, a dominant aspect of ripening of cotton, pecan, and some other fruits. PMID:16658260

  5. Ethylene: Response of Fruit Dehiscence to CO(2) and Reduced Pressure.

    Science.gov (United States)

    Lipe, J A; Morgan, P W

    1972-12-01

    These studies were conducted to determine whether ethylene serves as a natural regulator of fruit wall dehiscence, a major visible feature of ripening in some fruits. We employed treatments to inhibit ethylene action or remove ethylene and observed their effect on fruit dehiscence. CO(2) (13%), a competitive inhibitor of ethylene action in many systems, readily delayed dehiscence of detached fruits of cotton (Gossypium hirsutum L.), pecan (Carya illinoensis [Wang.] K. Koch), and okra (Hibiscus esculentus L.). The CO(2) effect was duplicated by placing fruits under reduced pressure (200 millimeters mercury), to promote the escape of ethylene from the tissue. Dehiscence of detached fruits of these species as well as attached cotton fruits was delayed. The delay of dehiscence of cotton and okra by both treatments was achieved with fruit harvested at intervals from shortly after anthesis until shortly before natural dehiscence. Pecan fruits would not dehisce until approximately 1 month before natural dehiscence, and during that time, CO(2) and reduced pressure delayed dehiscence. CO(2) and ethylene were competitive in their effects on cotton fruit dehiscence. All of the results are compatible with a hypothetical role of ethylene as a natural regulator of dehiscence, a dominant aspect of ripening of cotton, pecan, and some other fruits.

  6. Membrane-based ethylene/ethane separation: The upper bound and beyond

    KAUST Repository

    Rungta, Meha

    2013-08-02

    Ethylene/ethane separation via cryogenic distillation is extremely energy-intensive, and membrane separation may provide an attractive alternative. In this paper, ethylene/ethane separation performance using polymeric membranes is summarized, and an experimental ethylene/ethane polymeric upper bound based on literature data is presented. A theoretical prediction of the ethylene/ethane upper bound is also presented, and shows good agreement with the experimental upper bound. Further, two ways to overcome the ethylene/ethane upper bound, based on increasing the sorption or diffusion selectivity, is also discussed, and a review on advanced membrane types such as facilitated transport membranes, zeolite and metal organic framework based membranes, and carbon molecular sieve membranes is presented. Of these, carbon membranes have shown the potential to surpass the polymeric ethylene/ethane upper bound performance. Furthermore, a convenient, potentially scalable method for tailoring the performance of carbon membranes for ethylene/ethane separation based on tuning the pyrolysis conditions has also been demonstrated. © 2013 American Institute of Chemical Engineers.

  7. First evidence of ethylene production by Fusarium mangiferae associated with mango malformation

    Science.gov (United States)

    Ansari, Mohammad Wahid; Shukla, Alok; Pant, Ramesh Chandra; Tuteja, Narendra

    2013-01-01

    Malformation is arguably the most crucial disease of mango (Mangifera indica L.) at present. It is receiving great attention not only because of its widespread and destructive nature but also because of its etiology and control is not absolutely understood. Recently, Fusarium mangiferae is found to be associated with mango malformation disease. There are indications that stress ethylene production could be involved in the disease. Here we have shown the first direct evidence of production of ethylene in pure culture of F. mangiferae obtained from mango. The study also revealed that all the isolates dissected from mango acquire morphological features of F. mangiferae showing most similarity to the features of species with accepted standard features. The isolates of F. mangiferae from mango were observed to produce ethylene in significant amounts, ranging from 9.28–13.66 n mol/g dry wt/day. The findings presented here suggest that F. mangiferae could contribute to the malformation of mango by producing ethylene and probably stimulating stress ethylene production in malformed tissue of mango. Ethylene might be produced through 2-oxoglutarate-dependent oxygenase-type ethylene-forming-enzyme (EFE) pathway in Fusarium sp, which needs to be investigated. PMID:23221756

  8. Identification of Solanum habrochaites loci that quantitatively influence tomato fruit ripening-associated ethylene emissions.

    Science.gov (United States)

    Dal Cin, Valeriano; Kevany, Brian; Fei, Zhangjun; Klee, Harry J

    2009-11-01

    The phytohormone ethylene is essential for ripening of climacteric fruits such as tomato. While many of the genes responsible for ethylene synthesis and perception have been identified, the regulatory network controlling autocatalytic climacteric ethylene synthesis is not well understood. In order to better understand the regulation of ripening-associated ethylene, we have exploited the genetic variation within Solanum Sect. Lycopersicon. In particular, we have used a near-isogenic population of S. habrochaites introgression lines to identify chromosome segments affecting ethylene emissions during ripening. S. habrochaites fruits produce much larger quantities of ethylene during ripening than do cultivated S. lycopersicum tomatoes. A total of 17 segments were identified; 3 had emissions more than twice the level of the tomato parent, 11 had less than a twofold increase and 3 had significantly reduced emissions at one or more ripening stages. While several of these segments co-segregate with known ethylene-related genes, many do not correspond to known genes. Thus, they may identify novel modes of regulation. These results illustrate the utility of wild relatives and their introgression lines to understand regulation of fruit ripening-related processes.

  9. Subcellular Localization and In Vivo Interactions of the Arabidopsis thaliana Ethylene Receptor Family Members

    Institute of Scientific and Technical Information of China (English)

    Christopher Grefen; Katrin St(a)dele; Kamil R(u)(z)i(c)ka; Petr Obrdlik; Klaus Harter; Jakub Horák

    2008-01-01

    The gaseous phytohormone ethylene regulates many developmental processes and responses to environmental conditions in higher plants.In Arabidopsis thaliana,ethylene perception and initiation of signaling are mediated by a family of five receptors which are related to prokaryotic two-component sensor histidine kinases.The transient expression of fluorescence-tagged receptors in tobacco (Nicotiana benthamiana) epidermal leaf cells demonstrated that all ethylene receptors are targeted to the ER endomembrane network and do not localize to the plasmalemma.In support of in planta overlay studies,the ethylene receptors form homomeric and heteromeric protein complexes at the ER in living plant cells,as shown by membrane recruitment assays.A comparable in vivo interaction pattern was found in the yeast mating-based split-ubiquitin system.The overlapping but distinct expression pattern of the ethylene receptor genes suggests a differential composition of the ethylene receptor complexes in different plant tissues.Our findings may have crucial functional implications on the ethylene receptor-mediated efficiency of hormone perception,induction of signaling,signal attenuation and output.

  10. Ethylene and 1-MCP regulate major volatile biosynthetic pathways in apple fruit.

    Science.gov (United States)

    Yang, Xiaotang; Song, Jun; Du, Lina; Forney, Charles; Campbell-Palmer, Leslie; Fillmore, Sherry; Wismer, Paul; Zhang, Zhaoqi

    2016-03-01

    The effects of ethylene and 1-methylcyclopropene (1-MCP) on apple fruit volatile biosynthesis and gene expression were investigated. Statistical analysis identified 17 genes that changed significantly in response to ethylene and 1-MCP treatments. Genes encoding branched-chain amino acid aminotransferase (BCAT), aromatic amino acid aminotransferase (ArAT) and amino acid decarboxylases (AADC) were up-regulated during ripening and further enhanced by ethylene treatment. Genes related to fatty acid synthesis and metabolism, including acyl-carrier-proteins (ACPs), malonyl-CoA:ACP transacylase (MCAT), acyl-ACP-desaturase (ACPD), lipoxygenase (LOX), hydroperoxide lyase (HPL), alcohol dehydrogenase (ADH), pyruvate decarboxylase (PDC2), β-oxidation, acyl-CoA synthetase (ACS), enoyl-CoA hydratase (ECHD), acyl-CoA dehydrogenase (ACAD), and alcohol acyltransferases (AATs) also increased during ripening and in response to ethylene treatment. Allene oxide synthase (AOS), alcohol dehydrogenase 1 (ADH1), 3-ketoacyl-CoA thiolase and branched-chain amino acid aminotransferase 2 (BCAT2) decreased in ethylene-treated fruit. Treatment with 1-MCP and ethylene generally produced opposite effects on related genes, which provides evidence that regulation of these genes is ethylene dependent. Crown Copyright © 2015. Published by Elsevier Ltd. All rights reserved.

  11. Roles of Carbohydrate Supply and Ethylene,Polyamines in Maize Kernel Set

    Institute of Scientific and Technical Information of China (English)

    Han-Yu Feng; Zhi-Min Wang; Fan-Na Kong; Min-Jie Zhang; Shun-Li Zhou

    2011-01-01

    Glucose appears to have an antagonistic relationship with ethylene and ethylene and polyaminesappear to play antagonistic roles in the abortion of seeds and fruits.Moreover,ethylene,spermidine,and spermine share a common biosynthetic precursor.The synchronous changes of them and therelationships with kernel set are currently unclear.Here,we stimulated maize(Zea mays L.)apical kernelset and studied their changes at 4,8,12,and 16 d after pollination(DAP).The status of the apicalkernels changed from abortion to set,showing a pattern similar to that of the middle kernels,withslow decrease in glucose and rapid decline in ethylene production,and a sharp increase in spermidineand spermine after four DAP.Synchronous changes in ethylene and spermidine were also observed.However,the ethylene production decreased slowly in the aborted apical kernels,the glucose andpolyamines concentrations were lower.Ethephon application did not block the change from abortion toset for the setting apical kernels.These data indicate that the developmental change may be accompaniedby an inhibition of adequate glucose to ethylene synthesis and subsequent promotion of spermidine andspermine synthesis,and adequate carbohydrate supply may play a key role in the developmental process.

  12. Dormancy removal in apple embryos by nitric oxide or cyanide involves modifications in ethylene biosynthetic pathway.

    Science.gov (United States)

    Gniazdowska, Agnieszka; Krasuska, Urszula; Bogatek, Renata

    2010-11-01

    The connection between classical phytohormone-ethylene and two signaling molecules, nitric oxide (NO) and hydrogen cyanide (HCN), was investigated in dormancy removal and germination "sensu stricto" of apple (Malus domestica Borkh.) embryos. Deep dormancy of apple embryos was removed by short-term (3-6 h) pre-treatment with NO or HCN. NO- or HCN-mediated stimulation of germination was associated with enhanced emission of ethylene by the embryos, coupled with transient increase in ROS concentration in embryos. Ethylene vapors stimulated germination of dormant apple embryos and eliminated morphological anomalies characteristic for young seedlings developed from dormant embryos. Inhibitors of ethylene receptors completely impeded beneficial effect of NO and HCN on embryo germination. NO- and HCN-induced ethylene emission by apple embryo was only slightly reduced by inhibitor of 1-aminocyclopropane-1-carboxylic acid (ACC) oxidase activity during first 4 days of germination. Short-term pre-treatment of the embryos with NO and HCN modified activity of both key enzymes of ethylene biosynthetic pathway: ACC synthase and ACC oxidase. Activity of ACC synthase declined during first 4 days of germination, while activity of ACC oxidase increased markedly at that time. Additional experiments point to non-enzymatic conversion of ACC to ethylene in the presence of ROS (H(2)O(2)). The results indicate that NO and HCN may alleviate dormancy of apple embryos "via" transient accumulation of ROS, leading to enhanced ethylene emission which is required to terminate germination "sensu stricto". Therefore, ethylene seems to be a trigger factor in control of apple embryo dormancy removal and germination.

  13. Ethylene and nitric oxide are involved in maintaining ion homeostasis in Arabidopsis callus under salt stress.

    Science.gov (United States)

    Wang, Huahua; Liang, Xiaolei; Wan, Qi; Wang, Xiaomin; Bi, Yurong

    2009-07-01

    In the present study, the role of ethylene in nitric oxide (NO)-mediated protection by modulating ion homeostasis in Arabidopsis callus under salt stress was investigated. Results showed that the ethylene-insensitive mutant etr1-3 was more sensitive to salt stress than the wild type (WT). Under 100 mM NaCl, etr1-3 callus displayed a greater electrolyte leakage and Na(+)/K(+) ratio but a lower plasma membrane (PM) H(+)-ATPase activity compared to WT callus. Application of exogenous 1-aminocyclopropane-1-carboxylic acid (ACC, an ethylene precursor) or sodium nitroprusside (SNP, a NO donor) alleviated NaCl-induced injury by maintaining a lower Na(+)/K(+) ratio and an increased PM H(+)-ATPase activity in WT callus but not in etr1-3 callus. The SNP actions in NaCl stress were attenuated by a specific NO scavenger or an ethylene biosynthesis inhibitor in WT callus. Under 100 mM NaCl, the NO accumulation and ethylene emission appeared at early time, and NO production greatly stimulated ethylene emission in WT callus. In addition, ethylene induced the expression of PM H(+)-ATPase genes under salt stress. The recovery experiment showed that NaCl-induced injury was reversible, as signaled by the similar recovery of Na(+)/K(+) ratio and PM H(+)-ATPase activity in WT callus. Taken together, the results indicate that ethylene and NO cooperate in stimulating PM H(+)-ATPase activity to modulate ion homeostasis for salt tolerance, and ethylene may be a part of the downstream signal molecular in NO action.

  14. Ethylene-mediated regulation of gibberellin content and growth in helianthus annuus L

    Energy Technology Data Exchange (ETDEWEB)

    Pearce, D.W.; Reid, D.M.; Pharis, R.P. (Univ. of Calgary, Alberta (Canada))

    1991-04-01

    Elongation of hypocotyls of sunflower can be promoted by gibberellins (GAs) and inhibited by ethylene. The role of these hormones in regulating elongation was investigated by measuring changes in both endogenous GAs and in the metabolism of exogenous ({sup 3}H)- and ({sup 2}H{sub 2})GA{sub 20} in the hypocotyls of sunflower (Helianthus annuus L. cv Delgren 131) seedlings exposed to ethylene. The major biologically active GAs identified by gas chromatography-mass spectrometry were GA{sub 1}, GA{sub 19}, GA{sub 20}, and GA{sub 44}. In hypocotyls of seedlings exposed to ethylene, the concentration of GA{sub 1}, known to be directly active in regulating shoot elongation in a number of species, was reduced. Ethylene treatment reduced the metabolism of ({sup 3}H)GA{sub 20} and less ({sup 2}H{sub 2})GA{sub 1} was found in the hypocotyls of those seedlings exposed to the higher ethylene concentrations. However, it is not known if the effect of ethylene on GA{sub 20} metabolism was direct or indirect. In seedlings treated with exogenous GA{sub 1} or GA{sub 3}, the hypocotyls elongated faster than those of controls, but the GA treatment only partially overcame the inhibitory effect of ethylene on elongation. The authors conclude that GA content is a factor which may limit elongation in hypocotyls of sunflower, and that while exposure to ethylene results in reduced concentration of GA{sub 1} this is not sufficient per se to account for the inhibition of elongation caused by ethylene.

  15. Occupational exposure to ethylene oxide during pregnancy and association with adverse reproductive outcomes.

    Science.gov (United States)

    Gresie-Brusin, Daniela F; Kielkowski, Danuta; Baker, Abednego; Channa, Kalavati; Rees, David

    2007-07-01

    To investigate the association between exposure to ethylene oxide during pregnancy and adverse reproductive outcomes. Singleton pregnancies were analysed that: (1) had occurred in women working at the time of the study (2004) in hospital sterilising units using ethylene oxide in Gauteng province, South Africa; (2) was the last recognised pregnancy of these women after the 1 January 1992; and (3) this last recorded pregnancy had occurred while the mother was employed. An adverse reproductive outcome was defined as the occurrence of a spontaneous abortion, still birth or pregnancy loss (combined abortion + still birth). Information on the evolution and outcome of the pregnancy was gathered from the mother using a questionnaire. Information on exposure to ethylene oxide during pregnancy was obtained from three sources, namely walk-through surveys, questionnaire-collected data and measurements of the levels of ethylene oxide in sterilising units at the time of the study (personal and static sampling). The study enrolled 69% of the hospitals in Gauteng using ethylene oxide to sterilise medical equipment. The participation rate for women employed in these sterilising units was 97%, and the study population consisted of 98 singleton pregnancies. Measurements of ethylene oxide showed that operators of sterilisers were still potentially over-exposed. There was a significantly increased risk of spontaneous abortion (POR = 20.8, 95% CI = 2.1-199) and pregnancy loss (POR = 8.6, 95% CI = 1.8-43.7) for pregnancies highly exposed to ethylene oxide compared to low exposed pregnancies. No associations were found between exposure to ethylene oxide and stillbirth. An increased risk of spontaneous abortion and pregnancy loss was found to be associated with exposure to ethylene oxide during pregnancy.

  16. Calcium ion dependency of ethylene production in segments of primary roots of Zea mays

    Science.gov (United States)

    Hasenstein, K. H.; Evans, M. L.

    1986-01-01

    We investigated the effect of Ca2+ on ethylene production in 2-cm long apical segments from primary roots of corn (Zea mays L., B73 x Missouri 17) seedlings. The seedlings were raised under different conditions of Ca2+ availability. Low-Ca and high-Ca seedlings were raised by soaking the grains and watering the seedlings with distilled water or 10 mM CaCl2, respectively. Segments from high-Ca roots produced more than twice as much ethylene as segments from low-Ca roots. Indoleacetic acid (IAA; 1 micromole) enhanced ethylene production in segments from both low-Ca and high-Ca roots but auxin-induced promotion of ethylene production was consistently higher in segments from high-Ca roots. Addition of 1-aminocyclopropane-1-carboxylic acid (ACC) to root segments from low-Ca seedlings doubled total ethylene production and the rate of production remained fairly constant during a 24 h period of monitoring. In segments from high-Ca seedlings ACC also increased total ethylene production but most of the ethylene was produced within the first 6 h. The data suggest that Ca2+ enhances the conversion of ACC to ethylene. The terminal 2 mm of the root tip were found to be especially important to ethylene biosynthesis by apical segments and, experiments using 45Ca2+ as tracer indicated that the apical 2 mm of the root is the region of strongest Ca2+ accumulation. Other cations such as Mn2+, Mg2+, and K+ could largely substitute for Ca2+. The significance of these findings is discussed with respect to recent evidence for gravity-induced Ca2+ redistribution and its relationship to the establishment of asymmetric growth during gravitropic curvature.

  17. Study of conformation and thermodynamics of α-amylase interaction with ethylene in vitro.

    Science.gov (United States)

    Hu, Yiwei; Zhang, Guangxian; Zhang, Fengxiu

    2016-10-01

    In this article, the conformation and thermodynamics of α-amylase interaction with ethylene in vitro were investigated. The ultraviolet (UV) absorption showed a strong peak of α-amylase treated with 6.04, 29.32 and 262.11μmolL(-1) ethylene appears at ~222nm and a weak peak at 278nm blue-shifted 1nm. Circular dichroism (CD) spectra indicated that the conformations of α-amylase treated with 29.32 and 262.11μmolL(-1) ethylene were obviously changed in which α-helix content were decreased by 20 and 31% respectively, and β-sheet, β-turn and random coil contents were increased by contrast. Fluorescence spectra suggested that the peak intensities of α-amylase at 342nm were obviously increased with the ethylene increase from 6.04 to 525.75μmolL(-1) and more than control group. The binding constants K between ethylene and α-amylase were 3.318×10(6), 4.407×10(6) and 5.125×10(6)Lmol(-1) at 288, 298 and 308K, respectively. And the calculated values of ΔH(0) and ΔS(0) are positive, which suggests that the interaction between ethylene and α-amylase is an endothermic reaction. The negative ΔG(0) values implied that the direct effect of ethylene on α-amylase conformation was spontaneous. The possible reason is that ethylene molecules were easily embedded into the interior of α-amylase in term of the hydrophobic force between α-amylase and ethylene, causing the conformation and thermodynamics changes of α-amylase.

  18. Interactions between Lugol's fixative and ethylene in the acetylene-reduction assay for nitrogenase activity in lake water.

    Science.gov (United States)

    Leonardson, L

    1980-05-01

    Lugol's solution is a practical and efficient fixative for the acetylene-reduction assay of nitrogenase activity in aquatic organisms. Correction must be made, however, for the solubility of ethylene in the liquid phase and reactions between Lugol's solution and ethylene. With a vapor phase-liquid phase volume ratio of 1.9:1, the mean solubility of ethylene in mixtures of lake water and Lugol's solution was 7.2%. No correlation was found between ethylene solubility and the concentration of Lugol's solution. Storage of fixed samples for more than 1 day before gas chromatographic analysis resulted in increased loss of ethylene from the vapor phase; the loss amounted to ca. 18% after 3 days. Higher losses were noted at higher concentrations of Lugol's solution. Most probably these effects were caused by iodine addition to ethylene, as indicated by the consumption of ethylene by iodine-potassium iodide solutions. The reaction was catalyzed by the rubber septa of the incubaton vessels when the septa were in contact with the liquid phase. Loss of ethylene decreased with increased concentration of phytoplankton because the organisms absorbed iodine. By using a standardized technique and determining ethylene solubility and reaction patterns between ethylene and the mixture of water and Lugol's solution, it is possible to correct for the loss of ethylene.

  19. CHARACTERISTICS OF STRUCTURE OF IMPACT COPOLYMERS OF POLYPROPYLENE WITH LOW ETHYLENE CONTENTS

    Institute of Scientific and Technical Information of China (English)

    MA Dezhu; LI Xiqiang; ZHANG Ruiyun; HONG Kunlun; LUO Xiaolie

    1994-01-01

    In the present work, the structure and impact properties of copolymers of polypropylene with low ethylene contents have been investigated. Based on the results of 13C-NMR, FTIR,WAXD, DSC, PLM and SEM, the relationship between impact properties and morphology of the copolymers has been discussed. The high impact properties of copolymer ICP2 may attribute to the relatively higher ethylene content and homogeneous ethylene unit distribution. The size and its distribution of spherulite in the copolymers and cycloid cavities dispersed in polypropylene continue phase may also be two important factors which affect the impact properties of these materials.

  20. Compositional Analysis of the High Molecular Weight Ethylene Oxide Propylene Oxide Copolymer by MALDI Mass Spectrometry

    CERN Document Server

    Houshia, Orwa Jaber

    2012-01-01

    The composition of narrow distribution poly ethylene oxide-propylene oxide copolymer (Mw ~ 8700 Da) was studied using matrix assisted laser desorption ionization (MALDI) mass spectrometry. The ethylene oxide-propylene oxide copolymer produced oligomers separated by 14 Da. The average resolving power over the entire spectrum was 28,000. Approximately 448 isotopically resolved peaks representing about 56 oligomers are identified. Although agreement between experimental and calculated isotopic distributions was strong, the compositional assignment was difficult. This is due to the large number of possible isobaric components. The purpose of this research is to resolve and study the composition of high mass copolymer such as ethylene oxide-propylene oxide.