WorldWideScience

Sample records for multiplexed phase modulated

  1. Digital coherent receiver for subcarrier multiplexed phase modulated radio-over-fibre signals

    DEFF Research Database (Denmark)

    Zibar, Darko; Larsen, Knud J.; Tafur Monroy, Idelfonso

    2009-01-01

    Digital coherent detection of multi-channel subcarrier multiplexed optically phase-modulated radio-over-fibre signals is experimentally demonstrated. Successful detection after transmission over a 40 km long fibre link of four or five 25 Mbaud BPSK/QPSK subcarrier channels in 5 GHz bandwidth...... is demonstrated using offline digital signal processing....

  2. Simultaneous two-wavelength phase unwrapping using an external module for multiplexing off-axis holography.

    Science.gov (United States)

    Turko, Nir A; Shaked, Natan T

    2017-01-01

    We present a dual-wavelength external holographic microscopy module for quantitative phase imaging of 3D structures with extended thickness range. This is done by simultaneous acquisition of two off-axis interferograms, each at a different wavelength, and generation of a synthetic wavelength, which is larger than the sample optical thickness, allowing two-wavelength unwrapping. The simultaneous acquisition is carried out by using optical multiplexing of the two interferograms onto the camera, where each of them has orthogonal off-axis interference fringe direction in relation to the other one. We used the system to quantitatively image a 7.96 μm step target and 30.5 μm circular copper pillars.

  3. Prescaled phase-locked loop using phase modulation and spectral filtering and its application to clock extraction from 160-Gbit/s optical-time-division multiplexed signal.

    Science.gov (United States)

    Igarashi, Koji; Katoh, Kazuhiro; Kikuchi, Kazuro

    2006-05-01

    We propose a prescaled phase-locked loop (PLL) using a simple optoelectronic phase comparator based on phase modulation and spectral filtering. Our phase comparator has a high dynamic range of over 9 dB and a high sensitivity comparable to that using an electrical mixer. A PLL composed of our phase comparator enables to extract a low-noise 10-GHz clock from a 160-Gbit/s optical-time-division multiplexed (OTDM) signal.

  4. Coherent Detection of Wavelength Division Multiplexed Phase-Modulated Radio-over-Fibre Signals

    DEFF Research Database (Denmark)

    Zibar, Darko; Yu, Xianbin; Peucheret, Christophe

    2008-01-01

    A WDM phase-modulated Radio-over-Fibre link using digital coherent detection is experimentally demonstrated. 3 times 50 Mb/s WDM transmission of a BPSK modulated 5 GHz RF carrier is achieved over 25 km.......A WDM phase-modulated Radio-over-Fibre link using digital coherent detection is experimentally demonstrated. 3 times 50 Mb/s WDM transmission of a BPSK modulated 5 GHz RF carrier is achieved over 25 km....

  5. Multiple-image encryption and multiplexing using a modified Gerchberg-Saxton algorithm and phase modulation in Fresnel-transform domain.

    Science.gov (United States)

    Hwang, Hone-Ene; Chang, Hsuan T; Lie, Wen-Nung

    2009-12-15

    What we believe to be a new technique, based on a modified Gerchberg-Saxton algorithm (MGSA) and a phase modulation scheme in the Fresnel-transform domain, is proposed to reduce cross talks existing in multiple-image encryption and multiplexing. First, each plain image is encoded and multiplexed into a phase function by using the MGSA and a different wavelength/position parameter. Then all the created phase functions are phase modulated to result in different shift amounts of the reconstruction images before being combined together into a single phase-only function. Simulation results show that the cross talks between multiplexed images have been significantly reduced, compared with prior methods [Opt. Lett.30, 1306 (2005); J. Opt. A8, 391 (2006)], thus presenting high promise in increasing the multiplexing capacity and encrypting grayscale and color images.

  6. Optical phase-modulated radio-over-fiber links with k-means algorithm for digital demodulation of 8PSK subcarrier multiplexed signals

    DEFF Research Database (Denmark)

    Guerrero Gonzalez, Neil; Zibar, Darko; Yu, Xianbin

    2010-01-01

    A k-means algorithm for phase recovery of three, 50 Mbaud, 8PSK subcarrier multiplexed signals at 5 GHz for optical phase-modulated radio-over-fiber is proposed and experimentally demonstrated after 40 km of single mode fiber transmission......A k-means algorithm for phase recovery of three, 50 Mbaud, 8PSK subcarrier multiplexed signals at 5 GHz for optical phase-modulated radio-over-fiber is proposed and experimentally demonstrated after 40 km of single mode fiber transmission...

  7. Air segmented amplitude modulated multiplexed flow analysis with software-based phase recognition: determination of phosphate ion.

    Science.gov (United States)

    Ogusu, Takeshi; Uchimoto, Katsuya; Takeuchi, Masaki; Tanaka, Hideji

    2014-01-01

    Amplitude modulated multiplexed flow analysis (AMMFA) has been improved by introducing air segmentation and software-based phase recognition. Sample solutions, the flow rates of which are respectively varied at different frequencies, are merged. Air is introduced to the merged liquid stream in order to limit the dispersion of analytes within each liquid segment separated by air bubbles. The stream is led to a detector with no physical deaeration. Air signals are distinguished from liquid signals through the analysis of detector output signals, and are suppressed down to the level of liquid signals. Resulting signals are smoothed based on moving average computation. Thus processed signals are analyzed by fast Fourier transform. The analytes in the samples are respectively determined from the amplitudes of the corresponding wave components obtained. The developed system has been applied to the simultaneous determinations of phosphate ions in water samples by a Malachite Green method. The linearity of the analytical curve (0.0-31.0 μmol dm(-3)) is good (r(2)>0.999) and the detection limit (3.3 σ) at the modulation period of 30s is 0.52 μmol dm(-3). Good recoveries around 100% have been obtained for phosphate ions spiked into real water samples.

  8. Simultaneous polarization-insensitive phase-space trans-multiplexing and wavelength multicasting via cross-phase modulation in a photonic crystal fiber at 10 GBd

    Science.gov (United States)

    Cannon, Brice M.

    This thesis investigates the all-optical combination of amplitude and phase modulated signals into one unified multi-level phase modulated signal, utilizing the Kerr nonlinearity of cross-phase modulation (XPM). Predominantly, the first experimental demonstration of simultaneous polarization-insensitive phase-transmultiplexing and multicasting (PI-PTMM) will be discussed. The PI-PTMM operation combines the data of a single 10-Gbaud carrier-suppressed return-to-zero (CSRZ) on-off keyed (OOK) pump signal and 4x10-Gbaud return-to-zero (RZ) binary phase-shift keyed (BPSK) probe signals to generate 4x10-GBd RZ-quadrature phase-shift keyed (QPSK) signals utilizing a highly nonlinear, birefringent photonic crystal fiber (PCF). Since XPM is a highly polarization dependent nonlinearity, a polarization sensitivity reduction technique was used to alleviate the fluctuations due to the remotely generated signals' unpredictable states of polarization (SOP). The measured amplified spontaneous emission (ASE) limited receiver sensitivity optical signal-to-noise ratio (OSNR) penalty of the PI-PTMM signal relative to the field-programmable gate array (FPGA) pre-coded RZ-DQPSK baseline at a forward-error correction (FEC) limit of 10-3 BER was ≈ 0.3 dB. In addition, the OSNR of the remotely generated CSRZ-OOK signal could be degraded to ≈ 29 dB/0.1nm, before the bit error rate (BER) performance of the PI-PTMM operation began to exponentially degrade. A 138-km dispersion-managed recirculating loop system with a 100-GHz, 13-channel mixed-format dense-wavelength-division multiplexed (DWDM) transmitter was constructed to investigate the effect of metro/long-haul transmission impairments. The PI-PTMM DQPSK and the FPGA pre-coded RZ-DQPSK baseline signals were transmitted 1,900 km and 2,400 km in the nonlinearity-limited transmission regime before reaching the 10-3 BER FEC limit. The relative reduction in transmission distance for the PI-PTMM signal was due to the additional transmitter

  9. Nanophotonic modal dichroism: mode-multiplexed modulators.

    Science.gov (United States)

    Das, Susobhan; Fardad, Shima; Kim, Inki; Rho, Junsuk; Hui, Rongqing; Salandrino, Alessandro

    2016-09-15

    As the diffraction limit is approached, device miniaturization to integrate more functionality per area becomes more and more challenging. Here we propose a strategy to increase the functionality-per-area by exploiting the modal properties of a waveguide system. With such an approach the design of a mode-multiplexed nanophotonic modulator relying on the mode-selective absorption of a patterned indium-tin-oxide (ITO) is proposed. Full-wave simulations of a device operating at the telecom wavelength of 1550 nm show that two modes can be independently modulated, while maintaining performances in line with conventional single-mode ITO modulators reported in the recent literature. The proposed design principles can pave the way to a class of mode-multiplexed compact photonic devices able to effectively multiply the functionality-per-area in integrated photonic systems.

  10. Multiplexed Colorimetric Solid-Phase Extraction

    Science.gov (United States)

    Gazda, Daniel B.; Fritz, James S.; Porter, Marc D.

    2009-01-01

    Multiplexed colorimetric solid-phase extraction (MC-SPE) is an extension of colorimetric solid-phase extraction (C-SPE) an analytical platform that combines colorimetric reagents, solid phase extraction, and diffuse reflectance spectroscopy to quantify trace analytes in water. In CSPE, analytes are extracted and complexed on the surface of an extraction membrane impregnated with a colorimetric reagent. The analytes are then quantified directly on the membrane surface using a handheld diffuse reflectance spectrophotometer. Importantly, the use of solid-phase extraction membranes as the matrix for impregnation of the colorimetric reagents creates a concentration factor that enables the detection of low concentrations of analytes in small sample volumes. In extending C-SPE to a multiplexed format, a filter holder that incorporates discrete analysis channels and a jig that facilitates the concurrent operation of multiple sample syringes have been designed, enabling the simultaneous determination of multiple analytes. Separate, single analyte membranes, placed in a readout cartridge create unique, analyte-specific addresses at the exit of each channel. Following sample exposure, the diffuse reflectance spectrum of each address is collected serially and the Kubelka-Munk function is used to quantify each water quality parameter via calibration curves. In a demonstration, MC-SPE was used to measure the pH of a sample and quantitate Ag(I) and Ni(II).

  11. Multiplexing technique using amplitude-modulated chirped fiber Bragg gratings

    Science.gov (United States)

    Wong, Allan C. L.; Childs, Paul A.; Peng, Gang-Ding

    2007-07-01

    We propose a new multiplexing technique using amplitude-modulated chirped fiber Bragg gratings that have an identical center Bragg wavelength. Each grating is inscribed with a unique amplitude modulation that allows them to be multiplexed with complete overlapping within a certain bandwidth. To demodulate the multiplexed signal, the discrete wavelet transform is employed. Concurrently, a wavelet denoising technique is used to reduce the noise. This proposed multiplexing technique has been verified through strain measurements. Experimental results showed that for strains applied up to 1250 μɛ the absolute error and cross-talk are within ±20 μɛ and 16 μɛ, respectively. A strain resolution of 4 μɛ is obtained.

  12. Multiplexed noise shaping structures for Delta-Sigma modulators

    Science.gov (United States)

    Czarnul, Z.; Yesilyurt, A. G.; Temes, G. C.

    1991-12-01

    A new structure for realizing a multiplexed noise-shaping A/D convertor is proposed. It improves the performance of first- or second-order Delta-Sigma modulators by employing additional feedback paths for suppressing the quantizer error. The structure, its theoretical analysis, and simulations confirming the improved resolution are presented.

  13. Final Report Nucleic Acid System - Hybrid PCR and Multiplex Assay Project Phase 2

    Energy Technology Data Exchange (ETDEWEB)

    Koopman, R P; Langlois, R G; Nasarabadi, S; Benett, W J; Colston, B W; Johnson, D C; Brown, S B; Stratton, P L; Milanovich, F P

    2002-04-17

    This report covers phase 2 (year 2) of the Nucleic Acid System--Hybrid PCR and Multiplex Assay project. The objective of the project is to reduce to practice the detection and identification of biological warfare pathogens by the nucleic acid recognition technique of PCR (polymerase chain reaction) in a multiplex mode using flow cytometry. The Hybrid instrument consists of a flow-through PCR module capable of handling a multiplexed PCR assay, a hybridizing module capable of hybridizing multiplexed PCR amplicons and beads, and a flow cytometer module for bead-based identification, all controlled by a single computer. Multiplex immunoassay using bead-based Luminex flow cytometry is available, allowing rapid screening for many agents. PCR is highly specific and complements and verifies immunoassay. It can also be multiplexed and detection provided using the bead-based Luminex flow cytometer. This approach allows full access to the speed and 100-fold multiplex capability of flow cytometry for rapid screening as well as the accuracy and specificity of PCR. This project has two principal activities: (1) Design, build and test a prototype hybrid PCR/flow cytometer with the basic capabilities for rapid, broad spectrum detection and identification, and (2) Develop and evaluate multiplex flow analysis assay protocols and reagents for the simultaneous detection of PCR products. This project requires not only building operationally functional instrumentation but also developing the chemical assays for detection of priority pathogens. This involves development and evaluation of multiplex flow analysis assay protocols and reagents for the simultaneous detection of PCR products.

  14. Combined Transmission of Baseband NRZ-DQPSK and Phase Modulated Radio-over-Fibre

    DEFF Research Database (Denmark)

    Jensen, Jesper Bevensee; Yu, Xianbin; Tafur Monroy, Idelfonso

    2008-01-01

    21.4 Gbit/s baseband DQPSK and 1.25 Gbit/s phase modulated RoF was transmitted over 80 km SSMF using polarization multiplexing.......21.4 Gbit/s baseband DQPSK and 1.25 Gbit/s phase modulated RoF was transmitted over 80 km SSMF using polarization multiplexing....

  15. Multichannel mode conversion and multiplexing based on a single spatial light modulator for optical communication

    Science.gov (United States)

    Nie, Song; Yu, Song; Cai, Shanyong; Lan, Mingying; Gu, Wanyi

    2016-07-01

    A method is proposed to achieve multichannel mode conversion and multiplexing by dividing a single spatial light modulator into several blocks with the mode conversion pattern and blazed grating loaded on each block. The conversion patterns realize the precise excitation of higher order modes using combined amplitude and phase modulation. The blazed gratings bring together incident beams, so these beams can be coupled into few-mode fiber (FMF). In the experiment, four higher order modes are precisely excited and converge with a tilt angle. Through the simulation method, these beams can be coupled into FMF with small tilt angles (0.0344 deg for LP11 mode).

  16. Multiplexed absorption tomography with calibration-free wavelength modulation spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Cai, Weiwei; Kaminski, Clemens F., E-mail: cfk23@cam.ac.uk [Department of Chemical Engineering and Biotechnology, University of Cambridge, Cambridge CB2 3RA (United Kingdom)

    2014-04-14

    We propose a multiplexed absorption tomography technique, which uses calibration-free wavelength modulation spectroscopy with tunable semiconductor lasers for the simultaneous imaging of temperature and species concentration in harsh combustion environments. Compared with the commonly used direct absorption spectroscopy (DAS) counterpart, the present variant enjoys better signal-to-noise ratios and requires no baseline fitting, a particularly desirable feature for high-pressure applications, where adjacent absorption features overlap and interfere severely. We present proof-of-concept numerical demonstrations of the technique using realistic phantom models of harsh combustion environments and prove that the proposed techniques outperform currently available tomography techniques based on DAS.

  17. Investigation of modulation parameters in multiplexing gas chromatography.

    Science.gov (United States)

    Trapp, Oliver

    2010-10-22

    Combination of information technology and separation sciences opens a new avenue to achieve high sample throughputs and therefore is of great interest to bypass bottlenecks in catalyst screening of parallelized reactors or using multitier well plates in reaction optimization. Multiplexing gas chromatography utilizes pseudo-random injection sequences derived from Hadamard matrices to perform rapid sample injections which gives a convoluted chromatogram containing the information of a single sample or of several samples with similar analyte composition. The conventional chromatogram is obtained by application of the Hadamard transform using the known injection sequence or in case of several samples an averaged transformed chromatogram is obtained which can be used in a Gauss-Jordan deconvolution procedure to obtain all single chromatograms of the individual samples. The performance of such a system depends on the modulation precision and on the parameters, e.g. the sequence length and modulation interval. Here we demonstrate the effects of the sequence length and modulation interval on the deconvoluted chromatogram, peak shapes and peak integration for sequences between 9-bit (511 elements) and 13-bit (8191 elements) and modulation intervals Δt between 5 s and 500 ms using a mixture of five components. It could be demonstrated that even for high-speed modulation at time intervals of 500 ms the chromatographic information is very well preserved and that the separation efficiency can be improved by very narrow sample injections. Furthermore this study shows that the relative peak areas in multiplexed chromatograms do not deviate from conventionally recorded chromatograms. Copyright © 2010 Elsevier B.V. All rights reserved.

  18. Linear Frequency Modulated Signals VS Orthogonal Frequency Division Multiplexing Signals for Synthetic Aperture Radar Systems

    Science.gov (United States)

    2014-06-01

    FREQUENCY MODULATED SIGNALS VS ORTHOGONAL FREQUENCY DIVISION MULTIPLEXING SIGNALS FOR SYNTHETIC APERTURE RADAR SYSTEMS by Sade A. Holder June...SIGNALS VS ORTHOGONAL FREQUENCY DIVISION MULTIPLEXING SIGNALS FOR SYNTHETIC APERTURE RADAR SYSTEMS 5. FUNDING NUMBERS 6. AUTHOR(S) Sade A. Holder 7...OFDM) signal versus a linear frequency modulated or chirp signal on simulated synthetic aperture radar (SAR) imagery. Various parameters of the

  19. Air-segmented amplitude-modulated multiplexed flow analysis.

    Science.gov (United States)

    Inui, Koji; Uemura, Takeshi; Ogusu, Takeshi; Takeuchi, Masaki; Tanaka, Hideji

    2011-01-01

    Air-segmentation is applied to amplitude-modulated multiplexed flow analysis, which we proposed recently. Sample solutions, the flow rates of which are varied periodically, are merged with reagent and/or diluent solution. The merged stream is segmented by air-bubbles and, downstream, its absorbance is measured after deaeration. The analytes in the samples are quantified from the amplitudes of the respective wave components in the absorbance. The proposed method is applied to the determinations of a food dye, phosphate ions and nitrite ions. The air-segmentation is effective for limiting amplitude damping through the axial dispersion, resulting in an improvement in sensitivity. This effect is more pronounced at shorter control periods and longer flow path lengths.

  20. Multiple-image encryption based on phase mask multiplexing in fractional Fourier transform domain.

    Science.gov (United States)

    Liansheng, Sui; Meiting, Xin; Ailing, Tian

    2013-06-01

    A multiple-image encryption scheme is proposed based on the phase retrieval process and phase mask multiplexing in the fractional Fourier transform domain. First, each original gray-scale image is encoded into a phase only function by using the proposed phase retrieval process. Second, all the obtained phase functions are modulated into an interim, which is encrypted into the final ciphertext by using the fractional Fourier transform. From a plaintext image, a group of phase masks is generated in the encryption process. The corresponding decrypted image can be recovered from the ciphertext only with the correct phase mask group in the decryption process. Simulation results show that the proposed phase retrieval process has high convergence speed, and the encryption algorithm can avoid cross-talk; in addition, its encrypted capacity is considerably enhanced.

  1. Modulational instability of nematic phase

    Indian Academy of Sciences (India)

    T Mithun; K Porsezian

    2014-02-01

    We numerically observe the effect of homogeneous magnetic field on the modulationally stable case of polar phase in = 2 spinor Bose–Einstein condensates (BECs). Also we investigate the modulational instability of uniaxial and biaxial (BN) states of polar phase. Our observations show that the magnetic field triggers the modulational instability and demonstrate that irrespective of the magnetic field effect the uniaxial and biaxial nematic phases show modulational instability.

  2. Multiplexing technique using amplitude-modulated chirped fibre Bragg gratings with applications in two-parameter sensing

    Science.gov (United States)

    Wong, Allan C. L.; Childs, Paul A.; Peng, Gang-Ding

    2007-11-01

    A multiplexing technique using amplitude-modulated chirped fibre Bragg gratings (AMCFBGs) is presented. This technique realises the multiplexing of spectrally overlapped AMCFBGs with identical centre Bragg wavelength and bandwidth. Since it is fully compatible with the wavelength division multiplexing scheme, the number of gratings that can be multiplexed can be increased by several times. The discrete wavelet transform is used to demodulate such multiplexed signal. A wavelet denoising technique is applied to the multiplexed signal in conjunction with the demodulation. Strain measurements are performed to experimentally demonstrate the feasibility of this multiplexing technique. The absolute error and crosstalk are measured. An application to simultaneous two-parameter sensing is also demonstrated.

  3. Associative recall in a volume holographic storage system based on phase-code multiplexing

    Science.gov (United States)

    Berger, G.; Denz, C.; Orlov, S. S.; Phillips, B.; Hesselink, L.

    2001-12-01

    We present two different techniques on how to realize a content-addressed holographic memory when using phase-code multiplexing, relying on simple intensity measurements rather than phase distributions. Theoretical and experimental results of associative recall in a phase-coded system designed for digital data storage will be presented and compared to the corresponding method when using angular multiplexing.

  4. Multi-user multiplexed scheme for decoding modulated-encoded sequential information

    Science.gov (United States)

    Mosso, Fabian; Tebaldi, Myrian; Barrera, John Fredy; Bolognini, Néstor; Torroba, Roberto

    2011-08-01

    Encrypting procedures with multiplexed operations exhibit an inherent noise. We presented options to avoid background noise arising from the non-decoded images. We have a coding mask corresponding to each single input object, thus resulting in a static decrypting mechanism. Besides, if we manage the spatial destination of each decoded output, then we avoid the noise superposition. In those schemes, the displaying output order was irrelevant. However, when we face a sequence of events including multi-users, we need to develop another strategy. We present a multi-user encrypting scheme with a single encoding mask that removes the background noise, also showing the decrypted data in a prescribed sequence. The multiplexing scheme is based on the 4f double random phase encryption architecture and a theta modulation method, which consists in superposing each encrypted information with a determined sinusoidal grating. Afterwards we proceed to the completely encoded data multiplexing. In a multi-user scheme, we employ different encrypting masks in the 4f optical setup for each user, and the same mask is employed for the user sequence. We store the encrypted data in the single medium. After a Fourier transform operation and an appropriate filtering procedure, we reach the sequence of isolated encrypted spots corresponding to the right user. With the aid of the pertaining decoding mask, the user can decrypt the sequence. We avoid the noise by the appropriate choice of the modulating gratings pitch as to elude the overlapping of spots at the Fourier plane, which is the cause of information degradation.

  5. Spectral multiplexing using stacked volume-phase holographic gratings - I

    Science.gov (United States)

    Zanutta, A.; Landoni, M.; Riva, M.; Bianco, A.

    2017-08-01

    Many focal-reducer spectrographs, currently available at state-of-the-art telescopes facilities, would benefit from a simple refurbishing that could increase both the resolution and spectral range in order to cope with the progressively challenging scientific requirements, but, in order to make this update appealing, it should minimize the changes in the existing structure of the instrument. In the past, many authors proposed solutions based on stacking subsequently layers of dispersive elements and recording multiple spectra in one shot (multiplexing). Although this idea is promising, it brings several drawbacks and complexities that prevent the straightforward integration of such a device in a spectrograph. Fortunately, nowadays, the situation has changed dramatically, thanks to the successful experience achieved through photopolymeric holographic films, used to fabricate common volume-phase holographic gratings (VPHGs). Thanks to the various advantages made available by these materials in this context, we propose an innovative solution to design a stacked multiplexed VPHG that is able to secure efficiently different spectra in a single shot. This allows us to increase resolution and spectral range enabling astronomers to greatly economize their awarded time at the telescope. In this paper, we demonstrate the applicability of our solution, both in terms of expected performance and feasibility, supposing the upgrade of the Gran Telescopio CANARIAS (GTC) Optical System for Imaging and low-Intermediate-Resolution Integrated Spectroscopy (OSIRIS).

  6. Modulation Frequency Multiplexed Tunable Diode Laser Spectroscopy System for Simultaneous CO, CO2 Measurements

    Institute of Scientific and Technical Information of China (English)

    CHEN Dong; LIU Wen-Qing; ZHANG Yu-Jun; LIU Jian-Guo; WEI Qing-Nong; KAN Rui-Feng; WANG Min; CUI Yi-Ben; CHEN Jiu-Ying

    2006-01-01

    @@ A modulation frequency multiplexed dual diode-laser system is developed for simultaneous detection of the two most common fire gas products CO and CO2. Simultaneous detection is achieved by modulating each laser at different frequencies, demodulating the signal by a pair of lock-in amplifiers for each gas.

  7. Channel Capacity of DWDM Networks with Cross-phase Modulation Effect

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    In dense wavelength division multiplexing(DWDM) optical transmission systems, cross phase modulation(XPM) due to Kerr effect causes phase shift and intensity modulation in each channel, which will lead the channel capacity to be a random variable. An expression of the channel capacity dealing with XPM effect is presented, and the correctness and accuracy of this method are demonstrated by numerical simulation.

  8. Quantitative imaging of nanometric optical path length modulations by time-averaged heterodyne holography in coherent frequency-division multiplexing regime

    CERN Document Server

    Bruno, Francois; Lesaffre, Max; Verrier, Nicolas; Atlan, Michael

    2013-01-01

    We report a demonstration of amplitude and phase imaging of out-of-plane sinusoidal vibration at nanometer scales with a heterodyne holographic interferometer. Time-averaged holograms of a phase-modulated optical field are recorded with an exposure time much longer than the modulation period. Optical heterodyning, a frequency-conversion process aimed at shifting a given radiofrequency optical side band in the sensor bandwidth, is performed with an off-axis and frequency-shifted optical local oscillator. The originality of the proposed method is to make use of a multiplexed local oscillator to address several optical side bands into the temporal bandwidth of the sensor array. This process is called coherent frequency-division multiplexing. It enables simultaneous recording and pixel-to-pixel division of two side band holograms, which permits quantitative mapping of the modulation depth of local optical path lengths yielding small optical phase modulations. Additionally, a linear frequency chirp ensures the ret...

  9. Double random phase spread spectrum spread space technique for secure parallel optical multiplexing with individual encryption key

    Science.gov (United States)

    Hennelly, B. M.; Javidi, B.; Sheridan, J. T.

    2005-09-01

    A number of methods have been recently proposed in the literature for the encryption of 2-D information using linear optical systems. In particular the double random phase encoding system has received widespread attention. This system uses two Random Phase Keys (RPK) positioned in the input spatial domain and the spatial frequency domain and if these random phases are described by statistically independent white noises then the encrypted image can be shown to be a white noise. Decryption only requires knowledge of the RPK in the frequency domain. The RPK may be implemented using a Spatial Light Modulators (SLM). In this paper we propose and investigate the use of SLMs for secure optical multiplexing. We show that in this case it is possible to encrypt multiple images in parallel and multiplex them for transmission or storage. The signal energy is effectively spread in the spatial frequency domain. As expected the number of images that can be multiplexed together and recovered without loss is proportional to the ratio of the input image and the SLM resolution. Many more images may be multiplexed with some loss in recovery. Furthermore each individual encryption is more robust than traditional double random phase encoding since decryption requires knowledge of both RPK and a lowpass filter in order to despread the spectrum and decrypt the image. Numerical simulations are presented and discussed.

  10. Spike phase synchronization in multiplex cortical neural networks

    Science.gov (United States)

    Jalili, Mahdi

    2017-01-01

    In this paper we study synchronizability of two multiplex cortical networks: whole-cortex of hermaphrodite C. elegans and posterior cortex in male C. elegans. These networks are composed of two connection layers: network of chemical synapses and the one formed by gap junctions. This work studies the contribution of each layer on the phase synchronization of non-identical spiking Hindmarsh-Rose neurons. The network of male C. elegans shows higher phase synchronization than its randomized version, while it is not the case for hermaphrodite type. The random networks in each layer are constructed such that the nodes have the same degree as the original network, thus providing an unbiased comparison. In male C. elegans, although the gap junction network is sparser than the chemical network, it shows higher contribution in the synchronization phenomenon. This is not the case in hermaphrodite type, which is mainly due to significant less density of gap junction layer (0.013) as compared to chemical layer (0.028). Also, the gap junction network in this type has stronger community structure than the chemical network, and this is another driving factor for its weaker synchronizability.

  11. The decryption of random phase multiplexing encoding system

    Science.gov (United States)

    Lee, Hsiao-Yi; Liu, Jung-Ping; Chang, Chi-Ching; Yau, Hon-Fai; Chang, Tsung-Chien

    2004-10-01

    Random-phase-multiplexing storage using photorefractive crystals is one of the most important topics in the field of photorefractive optics. To achieve random phase recording, we can use a diffuser to encrypt the reference light in a holographic recording setup. To decrypt the recorded pattern, the same diffuser used in encryption must be used in the reconstruction light, and it must be set in the original orientation. In this way, a number of 2-D patterns can be stored in a single photorefractive crystal with a single diffuser set at different orientations for different patterns. A merit in this recording method is that the encryption is virtually not possible to be decrypted if the original diffuser for encrypting is not available. In this paper, we proposed a way to decrypt the encrypted information in a photorefractive lithium niobate crystal without the possession of the original diffuser. In this method, we suppose somehow we know one of the patterns stored in the crystal, and then we retrieve the original diffuser with this pattern. And ultimately all the other patterns stored in the crystal are decrypted and retrieved with this retrieved diffuser.

  12. Single-shot quantitative phase microscopy with color-multiplexed differential phase contrast (cDPC).

    Science.gov (United States)

    Phillips, Zachary F; Chen, Michael; Waller, Laura

    2017-01-01

    We present a new technique for quantitative phase and amplitude microscopy from a single color image with coded illumination. Our system consists of a commercial brightfield microscope with one hardware modification-an inexpensive 3D printed condenser insert. The method, color-multiplexed Differential Phase Contrast (cDPC), is a single-shot variant of Differential Phase Contrast (DPC), which recovers the phase of a sample from images with asymmetric illumination. We employ partially coherent illumination to achieve resolution corresponding to 2× the objective NA. Quantitative phase can then be used to synthesize DIC and phase contrast images or extract shape and density. We demonstrate amplitude and phase recovery at camera-limited frame rates (50 fps) for various in vitro cell samples and c. elegans in a micro-fluidic channel.

  13. Rapid, Time-Division Multiplexed, Direct Absorption- and Wavelength Modulation-Spectroscopy

    Directory of Open Access Journals (Sweden)

    Alexander Klein

    2014-11-01

    Full Text Available We present a tunable diode laser spectrometer with a novel, rapid time multiplexed direct absorption- and wavelength modulation-spectroscopy operation mode. The new technique allows enhancing the precision and dynamic range of a tunable diode laser absorption spectrometer without sacrificing accuracy. The spectroscopic technique combines the benefits of absolute concentration measurements using calibration-free direct tunable diode laser absorption spectroscopy (dTDLAS with the enhanced noise rejection of wavelength modulation spectroscopy (WMS. In this work we demonstrate for the first time a 125 Hz time division multiplexed (TDM-dTDLAS-WMS spectroscopic scheme by alternating the modulation of a DFB-laser between a triangle-ramp (dTDLAS and an additional 20 kHz sinusoidal modulation (WMS. The absolute concentration measurement via the dTDLAS-technique allows one to simultaneously calibrate the normalized 2f/1f-signal of the WMS-technique. A dTDLAS/WMS-spectrometer at 1.37 µm for H2O detection was built for experimental validation of the multiplexing scheme over a concentration range from 50 to 3000 ppmV (0.1 MPa, 293 K. A precision of 190 ppbV was achieved with an absorption length of 12.7 cm and an averaging time of two seconds. Our results show a five-fold improvement in precision over the entire concentration range and a significantly decreased averaging time of the spectrometer.

  14. Rapid, time-division multiplexed, direct absorption- and wavelength modulation-spectroscopy.

    Science.gov (United States)

    Klein, Alexander; Witzel, Oliver; Ebert, Volker

    2014-11-14

    We present a tunable diode laser spectrometer with a novel, rapid time multiplexed direct absorption- and wavelength modulation-spectroscopy operation mode. The new technique allows enhancing the precision and dynamic range of a tunable diode laser absorption spectrometer without sacrificing accuracy. The spectroscopic technique combines the benefits of absolute concentration measurements using calibration-free direct tunable diode laser absorption spectroscopy (dTDLAS) with the enhanced noise rejection of wavelength modulation spectroscopy (WMS). In this work we demonstrate for the first time a 125 Hz time division multiplexed (TDM-dTDLAS-WMS) spectroscopic scheme by alternating the modulation of a DFB-laser between a triangle-ramp (dTDLAS) and an additional 20 kHz sinusoidal modulation (WMS). The absolute concentration measurement via the dTDLAS-technique allows one to simultaneously calibrate the normalized 2f/1f-signal of the WMS-technique. A dTDLAS/WMS-spectrometer at 1.37 µm for H2O detection was built for experimental validation of the multiplexing scheme over a concentration range from 50 to 3000 ppmV (0.1 MPa, 293 K). A precision of 190 ppbV was achieved with an absorption length of 12.7 cm and an averaging time of two seconds. Our results show a five-fold improvement in precision over the entire concentration range and a significantly decreased averaging time of the spectrometer.

  15. Rapid, Time-Division Multiplexed, Direct Absorption- and Wavelength Modulation-Spectroscopy

    Science.gov (United States)

    Klein, Alexander; Witzel, Oliver; Ebert, Volker

    2014-01-01

    We present a tunable diode laser spectrometer with a novel, rapid time multiplexed direct absorption- and wavelength modulation-spectroscopy operation mode. The new technique allows enhancing the precision and dynamic range of a tunable diode laser absorption spectrometer without sacrificing accuracy. The spectroscopic technique combines the benefits of absolute concentration measurements using calibration-free direct tunable diode laser absorption spectroscopy (dTDLAS) with the enhanced noise rejection of wavelength modulation spectroscopy (WMS). In this work we demonstrate for the first time a 125 Hz time division multiplexed (TDM-dTDLAS-WMS) spectroscopic scheme by alternating the modulation of a DFB-laser between a triangle-ramp (dTDLAS) and an additional 20 kHz sinusoidal modulation (WMS). The absolute concentration measurement via the dTDLAS-technique allows one to simultaneously calibrate the normalized 2f/1f-signal of the WMS-technique. A dTDLAS/WMS-spectrometer at 1.37 μm for H2O detection was built for experimental validation of the multiplexing scheme over a concentration range from 50 to 3000 ppmV (0.1 MPa, 293 K). A precision of 190 ppbV was achieved with an absorption length of 12.7 cm and an averaging time of two seconds. Our results show a five-fold improvement in precision over the entire concentration range and a significantly decreased averaging time of the spectrometer. PMID:25405508

  16. Rapid, Time-Division Multiplexed, Direct Absorption- and Wavelength Modulation-Spectroscopy

    OpenAIRE

    Alexander Klein; Oliver Witzel; Volker Ebert

    2014-01-01

    We present a tunable diode laser spectrometer with a novel, rapid time multiplexed direct absorption- and wavelength modulation-spectroscopy operation mode. The new technique allows enhancing the precision and dynamic range of a tunable diode laser absorption spectrometer without sacrificing accuracy. The spectroscopic technique combines the benefits of absolute concentration measurements using calibration-free direct tunable diode laser absorption spectroscopy (dTDLAS) with the enhanced nois...

  17. Code Division Multiplexing Using AI Based Custom Constellation Scheme - Efficient Modulation for High Data rate Transmission

    Directory of Open Access Journals (Sweden)

    K.SESHADRI SASTRY,

    2010-06-01

    Full Text Available To achieve high bit rate in transmission over wireless channels frequency reuse is an encouraging concept . Rather than dividing allocated frequency spectrum into narrow band width channels , one for each user information is transmitted over a very wide frequency spectrum using the same carrier frequency within same frequency band . In this paper we propose code division multiplexing scheme in which Custom QAM modulator itself is used as code . The propose system is simulated and tested in Matlab 7.4.

  18. Cavity Voltage Phase Modulation MD

    CERN Document Server

    Mastoridis, Themistoklis; Molendijk, John; Timko, Helga; CERN. Geneva. ATS Department

    2016-01-01

    The LHC RF/LLRF system is currently configured for extremely stable RF voltage to minimize transient beam loading effects. The present scheme cannot be extended beyond nominal beam current since the demanded power would exceed the peak klystron power and lead to saturation. A new scheme has therefore been proposed: for beam currents above nominal (and possibly earlier), the cavity phase modulation by the beam will not be corrected (transient beam loading), but the strong RF feedback and One-Turn Delay feedback will still be active for loop and beam stability in physics. To achieve this, the voltage set point will be adapted for each bunch. The goal of this MD was to test a new algorithm that would adjust the voltage set point to achieve the cavity phase modulation that would minimize klystron forward power.

  19. Frequency division multiplexed microwave and baseband digital optical fiber link for phased array antennas

    Science.gov (United States)

    Heim, Peter J.; McClay, C. Phillip

    1990-05-01

    A frequency-division multiplexed optical fiber link is described in which microwave (1-8 GHz) and baseband digital (1-10 Mb/s) signals are combined electrically and transmitted through a direct-modulation microwave optical link. The microwave signal does not affect bit error rate (BER) performance of the Manchester-coded baseband digital data link. The baseband digital signal affects microwave signal quality by generating second-order intermodulation noise. The intermodulation noise power density is found to be proportional to both the microwave input power and the digital input power, enabling the system to be modeled as a mixer (AM modulator). The conversion loss for the digital signal is approximately 68 dB for a 1-GHz microwave signal and is highly dependent on the microwave frequency, reaching a minimum value of 41 dB at 4.5 GHz, corresponding to the laser diode relaxation oscillation frequency. It is shown that Manchester coding on the digital link places the intermodulation noise peak away from the microwave signal, preventing degradation of close-carrier phase noise (<1 kHz offset). A direct trade-off between intermodulation noise and digital link margin is developed to project system performance.

  20. Binary Intensity Modulation and Hybrid Ternary Modulation Applied to Multiplexing Objects Using Holographic Data Storage on a PVA/AA Photopolymer

    Directory of Open Access Journals (Sweden)

    Elena Fernandez

    2014-01-01

    Full Text Available Holographic data pages were multiplexed in a polyvinyl alcohol/acrylamide photopolymer and a liquid crystal device was used to modify the object beam and store objects in the material. A peristrophic multiplexing method was used to store a large number of objects in the same spot of the material. The objects were stored using two different modulations: binary intensity modulation and hybrid ternary modulation. Moreover, the bit error rate (BER of the images was calculated in order to compare which modulation is most appropriate to be used for holographic data storage.

  1. Pulse position modulation for a subcarrier-multiplexed optical fiber transmission system

    Science.gov (United States)

    Wickramasinghe, V. R.; Ghassemlooy, Zabih F.

    1996-11-01

    Subcarrier multiplexed (SCM) optical network s offer a near to medium term alternative solution over high cost, evolving digital technology to distribute broadband services. Majority of existing systems are based on analogue optical transmission techniques and their principle disadvantage is the sensitivity to noise and system nonlinearities. Therefore, conventional SCM systems impose stringent noise and linearity requirements and as a result their performance is limited. A simple and attractive solution is to introduce an appropriate second stage modulator in order to improve the receiver sensitivity, hence the system performance.In this paper a SCM optical transmission system employing pulse position modulation as a second stage modulator, for transmission of video, audio and data channels is reported. Signal to noise ratio measurements obtained shows an improvement in optical receiver sensitivity compared with standard SCM systems.

  2. 80-Channel Multiplexer-Demultiplexer Module for DWDM Communications using Hybrid AWG -- Interleaver Technology

    Science.gov (United States)

    Rablau, Corneliu; Bredthauer, Lance

    2007-10-01

    Aside from the more traditional data, voice and e-mail communications, new bandwidth intensive applications in the larger consumer markets, such as music, digital pictures and movies, have led to an explosive increase in the demand for transmission capacity for optical communications networks. This has resulted in a widespread deployment of Dense Wavelength Division Multiplexing (DWDM) as a means of increasing the communications capacity by multiplexing and transmitting signals of different wavelengths (establishing multiple communication channels) through a single strand of fiber. We report on the design, assembly and characterization of a 50-GHz, 80-channel Mux-Demux module for DWDM systems. The module has been assembled from two commercially available 100 GHz, 40-channel Array Waveguide Grating (AWG) modules and a 50-GHz to 100-GHz interleaver. Relevant performance parameters such as insertion loss, channel uniformity, next-channel isolation (crosstalk) and integrated cross-talk are presented and discussed in contrast with the performance of other competing technologies such as Thin-Film-Filter-based Mux-Demux devices.

  3. A 16x1 wavelength division multiplexer with integrated distributed Bragg reflector lasers and electroabsorption modulators

    Science.gov (United States)

    Young, M. G.; Koren, U.; Miller, B. I.; Newkirk, M. A.; Chien, M.; Zirngibl, M.; Dragone, C.; Tell, B.; Presby, H. M.; Raybon, G.

    1993-08-01

    We demonstrate the integrated operation of a 16x1 wavelength-division multiplexed (WDM) source with distributed Bragg reflector (DBR) lasers and electroabsorption modulators. By using repeated holographic exposures and wet chemical etching, 16 different wavelengths from 1.544 to 1.553 micron with an average channel spacing of 6 angstroms are obtained. A high-performance combiner is used to obtain a very uniform coupling into the single-output waveguide, and with the integration of an optical amplifier an average optical power of -8 dBm per channel is coupled into a single-mode fiber.

  4. Mining Functional Modules in Heterogeneous Biological Networks Using Multiplex PageRank Approach.

    Science.gov (United States)

    Li, Jun; Zhao, Patrick X

    2016-01-01

    Identification of functional modules/sub-networks in large-scale biological networks is one of the important research challenges in current bioinformatics and systems biology. Approaches have been developed to identify functional modules in single-class biological networks; however, methods for systematically and interactively mining multiple classes of heterogeneous biological networks are lacking. In this paper, we present a novel algorithm (called mPageRank) that utilizes the Multiplex PageRank approach to mine functional modules from two classes of biological networks. We demonstrate the capabilities of our approach by successfully mining functional biological modules through integrating expression-based gene-gene association networks and protein-protein interaction networks. We first compared the performance of our method with that of other methods using simulated data. We then applied our method to identify the cell division cycle related functional module and plant signaling defense-related functional module in the model plant Arabidopsis thaliana. Our results demonstrated that the mPageRank method is effective for mining sub-networks in both expression-based gene-gene association networks and protein-protein interaction networks, and has the potential to be adapted for the discovery of functional modules/sub-networks in other heterogeneous biological networks. The mPageRank executable program, source code, the datasets and results of the presented two case studies are publicly and freely available at http://plantgrn.noble.org/MPageRank/.

  5. Simultaneous all-optical demultiplexing and regeneration based on self-phase and cross-phase modulation in a dispersion shifted fiber

    DEFF Research Database (Denmark)

    Yu, Jianjun; Jeppesen, Palle

    2001-01-01

    Simultaneous demultiplexing and regeneration of 40-Gb/s optical time division multiplexed (OTDM) signal based on self-phase and cross-phase modulation in a dispersion shifted fiber is numerically and experimentally investigated. The optimal walkoff time between the control pulse and OTDM signal...

  6. Optical Vector Network Analyzer with an Improved Dynamic Range Based on a Polarization Multiplexing Electro-Optic Modulator

    Science.gov (United States)

    Wang, Qi; Wang, Wen-Ting; Chen, Wei; Liu, Jian-Guo; Zhu, Ning-Hua

    2017-05-01

    We present a new method to achieve an optical vector network analyzer (OVNA) based on a polarization multiplexing electro-optic modulator (PM-EOM) without an optical bandpass filter. Optical single sideband (OSSB) modulated signals with a tunable optical carrier-sideband ratio (OCSR) are obtained at the output of the PM-EOM. The OCSR can be flexibly tuned by controlling bias voltages of the PM-EOM. The dynamic range of the OVNA is expanded by taking the improvement of the OCSR into account. The transmission response of an optical device under test (ODUT) is measured based on one-to-one mapping from optical domain to electrical domain. By optimizing the OCSR of the OSSB modulated signals, the dynamic range of the OVNA can be effectively improved with 3.7 dB. An analytical model is derived to describe the transfer function of the ODUT. The magnitude and phase responses of a fiber Bragg grating are characterized with a large dynamic range. Supported by the National Natural Science Foundation of China under Grant Nos 61377070, 61090391 and 61675196, and the National High-Technology Research and Development Program of China under Grant No 2013AA014203.

  7. Decryption of a random-phase multiplexing recording system

    Science.gov (United States)

    Chang, Chi-Ching; Liu, Jung-Ping; Lee, Hsiao-Yi; Lin, Ching-Yang; Chang, Tsung-Chien; Yau, Hon-Fai

    2006-03-01

    In practice, decrypting a random-phase encrypted volume holographic data storage system is impossible unless the original random-phase plate for the encryption is available. However, this study demonstrates that under certain conditions, ways are available that can decrypt an encrypted photorefractive LiNbO3 crystal holographic storage system. In addition to presenting experimental results that show the efficacy of this decryption approach, problems and difficulties in the experiments are discussed.

  8. Cross-phase modulation-induced penalties in multichannel DWDM optical transport networks

    Institute of Scientific and Technical Information of China (English)

    Xu Zhu(朱栩); Qingji Zeng(曾庆济)

    2003-01-01

    In dense wavelength division multiplexing (DWDM) optical transmission systems, cross-phase modulation(XPM) due to Kerr effect causes phase shift on each channel, which will ultimately be transformed toamplitude noise that leads to power penalties. In this letter, the XPM-induced penalty in multi-channelDWDM systems is investigated theoretically and an applied algorithm that can be practically used inengineering design is proposed.

  9. Phase noise mitigation of QPSK signal utilizing phase-locked multiplexing of signal harmonics and amplitude saturation.

    Science.gov (United States)

    Mohajerin-Ariaei, Amirhossein; Ziyadi, Morteza; Chitgarha, Mohammad Reza; Almaiman, Ahmed; Cao, Yinwen; Shamee, Bishara; Yang, Jeng-Yuan; Akasaka, Youichi; Sekiya, Motoyoshi; Takasaka, Shigehiro; Sugizaki, Ryuichi; Touch, Joseph D; Tur, Moshe; Langrock, Carsten; Fejer, Martin M; Willner, Alan E

    2015-07-15

    We demonstrate an all-optical phase noise mitigation scheme based on the generation, delay, and coherent summation of higher order signal harmonics. The signal, its third-order harmonic, and their corresponding delayed variant conjugates create a staircase phase-transfer function that quantizes the phase of quadrature-phase-shift-keying (QPSK) signal to mitigate phase noise. The signal and the harmonics are automatically phase-locked multiplexed, avoiding the need for phase-based feedback loop and injection locking to maintain coherency. The residual phase noise converts to amplitude noise in the quantizer stage, which is suppressed by parametric amplification in the saturation regime. Phase noise reduction of ∼40% and OSNR-gain of ∼3  dB at BER 10(-3) are experimentally demonstrated for 20- and 30-Gbaud QPSK input signals.

  10. A directly phase-modulated light source

    CERN Document Server

    Yuan, Z L; Lucamarini, M; Roberts, G L; Dynes, J F; Shields, A J

    2016-01-01

    The art of imparting information onto a light wave by optical signal modulation is fundamental to all forms of optical communication. Among many schemes, direct modulation of laser diodes stands out as a simple, robust, and cost effective method. However, the simultaneous changes in intensity, frequency and phase are a drawback which has prevented its application in the field of secure quantum communication. Here, we propose and experimentally demonstrate a directly phase-modulated light source which overcomes the main disadvantages associated with direct modulation and is suitable for diverse applications such as coherent communications and quantum cryptography. The source separates the tasks of phase preparation and pulse generation between a pair of semiconductor lasers leading to very pure phase states. Moreover, the cavity enhanced electro-optic effect enables the first example of sub-volt halfwave phase modulation at high signal rates. The source is compact, stable and versatile, and we show its potenti...

  11. Multilevel Spatial Multiplexing -Space Time Trellis Coded Modulation System for Fast Fading MIMO Channel

    Directory of Open Access Journals (Sweden)

    K.Kavitha

    2014-03-01

    Full Text Available Multilevel Space Time Trellis Coded Modulation with antenna grouping, which has been proposed recently, has coding gain and diversity gain, which in turn provide high throughput with considerable low computational complexity. However its performance is limited by predefining the antenna groups per component codes. In this paper Multilevel Spatial Multiplexing-Space Time Trellis Coded Modulation (ML-SM-STTCM has been proposed, in which antenna group selection is made based on spatial modulation based on trellis coding proposed by Ertugrul Basar and team. This idea maximizes the spatial diversity. Since only selected antennas are used to transmit the signal, and also the antennas with less cross correlation are in the selected groups, we could able to achieve improved BER performance even in the fast fading channel. Since the antenna selection is based on the component code in the system, at the decoder without increase in the computational complexity, we could achieve better error performance. The performance of the proposed system is analysed with Viterbi decoding algorithm and sub optimal sequential decoding algorithm. In this system, the antenna groups are non-overlapping, hence, it needs Nt, the number transmitter antennas, more than what is required at time t. The computer simulation reveals that the proposed system gives better BER performance compared to Multilevel Space Time Trellis Coded Modulation (ML STTCM over fast fading channel with the same computational complexity both at the transmitter and receiver.

  12. Tone Modulation in a Passive OTDM Multiplexer for Clock Recovery from a 160 Gbit/s OTDM Signal

    Institute of Scientific and Technical Information of China (English)

    Tetsuya.; Miyazaki; Fumito; Kubota

    2003-01-01

    Tone modulation in a passive OTDM multiplexer for clock recovery from a 160-Gbit/s OTDM signal by using a base-rate receiver is demonstrated. We performed synchronous demultiplexing in back-to-back arrangement and optical sampling after 320-km transmission.

  13. A tunable and wideband microwave photonic phase shifter based on dual-polarization modulator

    Science.gov (United States)

    Peng, Zhengxue; Wen, Aijun; Gao, Yongsheng; Tu, Zhaoyang

    2017-01-01

    A microwave photonic phase shifter based on dual-polarization Mach-Zehnder modulator (DPol-MZM) is proposed and experimentally demonstrated in this paper. A polarization multiplexed double sideband (DSB) signal is produced by a DPol-MZM. An optical bandpass filter (OBPF) follows after the DPol-MZM to filter out the optical carrier and one sideband. The polarization multiplexed signal is converted into a linear polarization light by a polarizer (Pol), and then beat at a photodiode (PD) to obtain the phase shifted signal. Experiments are carried out, and a continuous phase shift from -180° to 180° over a wide microwave frequency range of 10-33 GHz can be achieved by changing the polarization state using a polarization controller (PC). We also studied the spurious free dynamic range (SFDR) in the experiments. The features of this proposed phase shifter are large operation bandwidth, full-range 360° phase shift, and simple structure.

  14. Chromatic characterization of ion-exchanged glass binary phase plates for mode-division multiplexing.

    Science.gov (United States)

    Prieto-Blanco, Xesús; Montero-Orille, Carlos; Moreno, Vicente; Mateo, Eduardo F; Liñares, Jesús

    2015-04-10

    Mode-division multiplexing (MDM) in few-mode fibers is regarded as a promising candidate to increase optical network capacity. A fundamental element for MDM is a modal transformer to LP modes which can be implemented in a free-space basis by using multiregion phase plates, that is, LP plates. Likewise, several wavelengths have to be used due to wavelength multiplexing purposes, optical amplification tasks, and so on. In this work we show that efficient monolithic binary phase plates for different wavelengths can be fabricated by ion-exchange in glass and used for MDM tasks. We introduce an optical characterization method of the chromatic properties of such phase plates which combines the inverse Wentzel-Kramers-Brillouin (IWKB) together with Mach-Zehnder and Michelson-based interferometric techniques. The interferometric method provides a measurement of the phase step for several wavelengths, which characterizes the chromatic properties of the phase plate. Consequently, it is shown that the IWKB method allows us to design and characterize the phase plates in an easy and fast way.

  15. Modeling interchannel four-wave mixing for 8-Ary modulated dense wavelength division multiplexing systems over dispersion map

    Science.gov (United States)

    Du, Jianxin; Shen, Ninghang; Xu, Yue

    2016-08-01

    Semianalytic models are developed to deterministically calculate the variances of degenerate and nondegenerate four-wave mixing (FWM) noises for dispersion-managed dense wavelength division multiplexing (DWDM) systems with 8-Ary modulations [i.e., 8-level amplitude- and differential phase-shift keying (8APSK) and constant-amplitude optical differential 8-level phase-shift keying (D8PSK)]. The semianalytic models include various important propagation effects for exact numerical results. A 5.28-Tb/s (40-Gs/s/ch) 100-GHz-spaced 33-channel DWDM system with a dispersion map is then numerically analyzed by using the newly derived semianalytic models. It is numerically validated that FWM impacts coming from 8APSK pump channels are more severe than those coming from D8PSK ones, where pump channels denote the channels whose energies are transferred to a probe channel through the FWM process. The numerical results show that although FWM tolerance of a central channel with 8APSK is worse than that with D8PSK, a central channel with 8APSK is still superior to that with D8PSK when some linear noises and FWM noise are simultaneously taken into account for our given system conditions, which is mainly attributed to a relatively larger minimum Euclidean distance for the 8APSK constellation than the D8PSK one.

  16. 40-Gbps vestigial sideband half-cycle Nyquist subcarrier modulation transmission experiment and its comparison with orthogonal frequency division multiplexing

    Science.gov (United States)

    Liu, Na; Chen, Xue; Ju, Cheng; Hui, Rongqing

    2014-09-01

    We experimentally demonstrate the superior performance of a 40-Gbps 16-QAM half-cycle Nyquist subcarrier modulation (SCM) transmission over a 100-km uncompensated standard single-mode fiber using dual-drive Mach-Zehnder modulator-based vestigial sideband intensity modulation and direct detection. The impact of modulator chirp on the system performance is experimentally evaluated. This Nyquist-SCM technique is compared with optical orthogonal frequency division multiplexing in both back-to-back and 100-km transmission experiments, and the results show that the Nyquist system has a better performance.

  17. Fabrication and characterization of ion-exchanged glass binary phase plates for mode-division multiplexing

    Science.gov (United States)

    Montero, Carlos; Moreno, Vicente; Prieto-Blanco, Xesús; Mateo, Eduardo F.; Ip, Ezra; Liñares, Jesús

    2012-01-01

    In response to ever growing data traffic, significant efforts are being made to increase optical network capacity. One promising candidate is mode-division multiplexing (MDM) in few-mode fibers, which uses space as a new information-bearing dimension. A fundamental element for MDM is a modal transformer. Modal transformation can be implemented in a free-space basis by using multi-region phase plates. In this work we present the design, fabrication and characterization of monolithic binary phase plates by highly-uniform Ag+/Na+ ion-exchange in glass. Diffracted optical field intensities have been measured and high quality mode transformation has been confirmed.

  18. Ultrarapid mutation detection by multiplex, solid-phase chemical cleavage

    Energy Technology Data Exchange (ETDEWEB)

    Rowley, G.; Saad, S.; Giannelli, F.; Green, P.M. [Guy`s & St. Thomas`s Hospitals, London (United Kingdom)

    1995-12-10

    The chemical cleavage of mismatches in heteroduplexes formed by probe and test DNA detects and locates any sequence change in long DNA segments ({approximately}1.8 kb), and its efficiency has been well tested in the analysis of both average (e.g., coagulation factor IX) and large, complex genes (e.g., coagulation factor VIII and dystrophin). In the latter application RT/PCR products allow the examination of all essential sequences of the gene in a minimum number of reactions. We use two specific chemical reactants (hydroxylamine and osmium tetroxide) and piperidine cleavage of the above procedure to develop a very fast mutation screening method. This is based on: (1) 5{prime} or internal fluorescent labeling to allow concurrent screening of three to four DNA fragments and (2) solid-phase chemistry to use a microliter format and reduce the time required for the procedure, from amplification of sequence to gel loading inclusive, to one person-working-day. We test the two variations of the method, one entailing 5{prime} labeling of probe DNA and the other uniform labeling of both probe and target DNA, by detecting 114 known hemophilia B (coagulation factor IX) mutations and by analyzing 129 new patients. Uniform labeling of both probe and target DNA prior to formation of the heteroduplexes leads to almost twofold redundancy in the ability to detect mutations. Alternatively, the latter procedure may offer very efficient though less than 100% screening for sequence changes with only hydroxylamine. The full method with two chemical reactions (hydroxylamine and osmium tetroxide) should allow one person to screen with virtually 100% accuracy more than 300 kb of sequence in three ABI 373 gels in 1 day. 26 refs., 7 figs., 1 tab.

  19. Digital coherent receiver for phase modulated radio-over-fibre optical links

    DEFF Research Database (Denmark)

    Zibar, Darko; Yu, Xianbin; Peucheret, Christophe

    2009-01-01

    A novel digital signal processing-based coherent receiver for phase-modulated radio-over-fiber (RoF) optical links is presented and demonstrated experimentally. Error-free demodulation of 50-Mbaud binary phase-shift keying (BPSK) and quadrature phase-shift keying data signal modulated on a 5-GHz...... radio-frequency (RF) carrier is experimentally demonstrated using the proposed digital coherent receiver. Additionally, a wavelength-division-multiplexing (WDM) phase-modulated RoF optical link is experimentally demonstrated. A 3 x50 Mb/s WDM transmission of a BPSK modulated 5-GHz RF carrier is achieved...... over 25 km for the WDM channel spacing of 12.5 and 25 GHz, respectively....

  20. Lateral shifting sensitivity of a ground glass for holographic encryption and multiplexing using phase conjugate readout algorithm

    Science.gov (United States)

    Sun, Ching-Cherng; Su, Wei-Chia; Wang, Bor; Chiou, Arthur E. T.

    2001-05-01

    An encryption-selectable holographic storage algorithm with use of random phase encoding and angular multiplexing is proposed and demonstrated. The pattern for storage can be encrypted and multiplexed with use of a ground glass, which is also used to decrypt the pattern. A phase conjugation of the reference beam is used to generate phase conjugate waves of the stored patterns. The lateral shifting sensitivity of the ground glass used to decrypt the information is theoretically analyzed and is compared with experimental measurement. The shifting tolerance for various ground glasses under imperfection phase reconstruction in the decryption processing is studied.

  1. Phase-Modulated Optical Communication Systems

    CERN Document Server

    Ho, Keang-Po

    2005-01-01

    Fiber-optic communication systems have revolutionized our telecommunication infrastructures – currently, almost all telephone land-line, cellular, and internet communications must travel via some form of optical fibers. In these transmission systems, neither the phase nor frequency of the optical signal carries information – only the intensity of the signal is used. To transmit more information in a single optical carrier, the phase of the optical carrier must be explored. As a result, there is renewed interest in phase-modulated optical communications, mainly in direct-detection DPSK signals for long-haul optical communication systems. When optical amplifiers are used to maintain certain signal level among the fiber link, the system is limited by amplifier noises and fiber nonlinearities. Phase-Modulated Optical Communication Systems surveys this newly popular area, covering the following topics: The transmitter and receiver for phase-modulated coherent lightwave systems Method for performance analysis o...

  2. Reconfigurable digital receiver for 8PSK subcarrier multiplexed and 16QAM single carrier phase‐modulated radio over fiber links

    DEFF Research Database (Denmark)

    Guerrero Gonzalez, Neil; Zibar, Darko; Yu, Xianbin

    2011-01-01

    A reconfigurable digital receiver based on the k‐means algorithm is proposed for phase‐modulated subcarrier multiplexed (SCM) and quadrature amplitude‐modulated single carrier, phase‐modulated radio‐over‐fiber links. We report successful demodulation after 40 km single mode fiber transmission...... with three 50 Mbaud 8PSK SCM signals and a 312.5 Mbaud 16QAM single carrier. © 2011 Wiley Periodicals, Inc. Microwave Opt Technol Lett 53:1015–1018, 2011; View this article online at wileyonlinelibrary.com. DOI 10.1002/mop.25905...

  3. Stable Optical Phase Modulation with Micromirrors

    CERN Document Server

    Knoernschild, Caleb; Maunz, Peter; Crain, Stephen; Kim, Jungsang

    2011-01-01

    We measure the motional fluctuations of a micromechanical mirror using a Michelson interferometer, and demonstrate its interferometric stability. The position stability of the micromirror is dominated by the thermal mechanical noise of the structure. With this level of stability, we utilize the micromirror to realize an ideal optical phase modulator by simply reflecting light off the mirror and modulating its position. The resonant frequency of the modulator can be tuned by applying a voltage between the mirror and an underlying electrode. Full modulation depth of +/-\\pi is achieved when the mirror resonantly excited with a sinusoidal voltage at an amplitude of 11V.

  4. Symmetry, phase modulation and nonlinear waves

    CERN Document Server

    Bridges, Thomas J

    2017-01-01

    Nonlinear waves are pervasive in nature, but are often elusive when they are modelled and analysed. This book develops a natural approach to the problem based on phase modulation. It is both an elaboration of the use of phase modulation for the study of nonlinear waves and a compendium of background results in mathematics, such as Hamiltonian systems, symplectic geometry, conservation laws, Noether theory, Lagrangian field theory and analysis, all of which combine to generate the new theory of phase modulation. While the build-up of theory can be intensive, the resulting emergent partial differential equations are relatively simple. A key outcome of the theory is that the coefficients in the emergent modulation equations are universal and easy to calculate. This book gives several examples of the implications in the theory of fluid mechanics and points to a wide range of new applications.

  5. Phase-Modulation Laser Interference Microscopy

    DEFF Research Database (Denmark)

    Brazhe, Alexey; Brazhe, Nadezda; Maximov, G. V.

    2008-01-01

    We describe how phase-modulation laser interference microscopy and wavelet analysis can be applied to noninvasive nonstained visualization and study of the structural and dynamical properties of living cells. We show how phase images of erythrocytes can reveal the difference between various...

  6. Detection and processing of phase modulated optical signals at 40 Gbit/s and beyond

    DEFF Research Database (Denmark)

    Geng, Yan

    This thesis addresses demodulation in direct detection systems and signal processing of high speed phase modulated signals in future all-optical wavelength division multiplexing (WDM) communication systems where differential phase shift keying (DPSK) or differential quadrature phase shift keying...... labeling has been proposed as an efficient way to implement packet routing and forwarding functionalities in future IP-over-WDM networks. An in-band subcarrier multiplexing (SCM) labeled signal using 40 Gbit/s DSPK payload and 25 Mbit/s non return-to-zero(NRZ) SCM label, is successfully transmitted over 80...... noise, and consequently degrade the performance of systems making use of RZ-DPSK format. All-optical signal regeneration avoiding O-E-O conversion is desired to improve signal quality in ultra long-haul transmission systems. Proof-of-principle numerical simulation results are provided, that suggest...

  7. Phase retrieval by coherent modulation imaging

    Science.gov (United States)

    Zhang, Fucai; Chen, Bo; Morrison, Graeme R.; Vila-Comamala, Joan; Guizar-Sicairos, Manuel; Robinson, Ian K.

    2016-11-01

    Phase retrieval is a long-standing problem in imaging when only the intensity of the wavefield can be recorded. Coherent diffraction imaging is a lensless technique that uses iterative algorithms to recover amplitude and phase contrast images from diffraction intensity data. For general samples, phase retrieval from a single-diffraction pattern has been an algorithmic and experimental challenge. Here we report a method of phase retrieval that uses a known modulation of the sample exit wave. This coherent modulation imaging method removes inherent ambiguities of coherent diffraction imaging and uses a reliable, rapidly converging iterative algorithm involving three planes. It works for extended samples, does not require tight support for convergence and relaxes dynamic range requirements on the detector. Coherent modulation imaging provides a robust method for imaging in materials and biological science, while its single-shot capability will benefit the investigation of dynamical processes with pulsed sources, such as X-ray free-electron lasers.

  8. Phase retrieval by coherent modulation imaging

    Science.gov (United States)

    Zhang, Fucai; Chen, Bo; Morrison, Graeme R.; Vila-Comamala, Joan; Guizar-Sicairos, Manuel; Robinson, Ian K.

    2016-01-01

    Phase retrieval is a long-standing problem in imaging when only the intensity of the wavefield can be recorded. Coherent diffraction imaging is a lensless technique that uses iterative algorithms to recover amplitude and phase contrast images from diffraction intensity data. For general samples, phase retrieval from a single-diffraction pattern has been an algorithmic and experimental challenge. Here we report a method of phase retrieval that uses a known modulation of the sample exit wave. This coherent modulation imaging method removes inherent ambiguities of coherent diffraction imaging and uses a reliable, rapidly converging iterative algorithm involving three planes. It works for extended samples, does not require tight support for convergence and relaxes dynamic range requirements on the detector. Coherent modulation imaging provides a robust method for imaging in materials and biological science, while its single-shot capability will benefit the investigation of dynamical processes with pulsed sources, such as X-ray free-electron lasers. PMID:27857061

  9. Directly Phase-Modulated Light Source

    Science.gov (United States)

    Yuan, Z. L.; Fröhlich, B.; Lucamarini, M.; Roberts, G. L.; Dynes, J. F.; Shields, A. J.

    2016-07-01

    The art of imparting information onto a light wave by optical signal modulation is fundamental to all forms of optical communication. Among many schemes, direct modulation of laser diodes stands out as a simple, robust, and cost-effective method. However, the simultaneous changes in intensity, frequency, and phase have prevented its application in the field of secure quantum communication. Here, we propose and experimentally demonstrate a directly phase-modulated light source which overcomes the main disadvantages associated with direct modulation and is suitable for diverse applications such as coherent communications and quantum cryptography. The source separates the tasks of phase preparation and pulse generation between a pair of semiconductor lasers leading to very pure phase states. Moreover, the cavity-enhanced electro-optic effect enables the first example of subvolt half-wave phase modulation at high signal rates. The source is compact, stable, and versatile, and we show its potential to become the standard transmitter for future quantum communication networks based on attenuated laser pulses.

  10. Ultrasonic sensor employing two cascaded phase-shifted fiber Bragg gratings suitable for multiplexing.

    Science.gov (United States)

    Wu, Qi; Okabe, Yoji

    2012-08-15

    An ultrasonic sensor based on two cascaded phase-shifted fiber Bragg gratings (PS-FBGs) is proposed and demonstrated. In place of an external cavity laser, a broadband amplified spontaneous emission light source is used to demonstrate multiplexing ability suitable for sensor networks. The system has a high sensitivity to ultrasonic waves generated by a PZT actuator placed 7.5 cm away from the PS-FBG, because of the steep slope in the center of the PS-FBG spectrum. A second advantage of the phase shift is to reduce the effective sensor length, leading to the achievement of broadband characteristics. A pencil lead break test was performed and all results are compared to a traditional PZT sensor.

  11. Phase multistability of self-modulated oscillations

    DEFF Research Database (Denmark)

    Sosnovtseva, Olga; Postnov, D.E.; Nekrasov, A.M.

    2002-01-01

    The paper examines the type of multistability that one can observe in the synchronization of two oscillators when the systems individually display self-modulation or other types of multicrest wave forms. The investigation is based on a phase reduction method and on the calculation of phase maps...... for vanishing and finite coupling strengths, respectively. Various phase-locked patterns are observed. In the presence of a frequency mismatch, the two-parameter bifurcation analysis reveals a set of synchronization regions inserted one into the other. Numerical examples using a generator with inertial...

  12. SIMULATION OF MULTIPLEXING OF TWO PHASE SOIL IN CASE OF COMPRESSION COMPRESSION

    Directory of Open Access Journals (Sweden)

    G. E. Agakhanov

    2016-01-01

    Full Text Available Aim.The article is devoted to solving the problem of finding metodoa seal a two phase soil layer under compression compression uniformly distributed load.Methods.On estimated model of a continuous isotropic body with linear and hereditary creep in case of invariance of the environment and a persistence of coefficient of Poisson in time, and also taking into account different resilience of a skeleton of soil when multiplexing and demultiplexing the decision of the task of multiplexing of a layer of two-phase soil in case of compression is received by a uniformly distributed load. Special cases of the intense deformed status are considered.Results.The analysis of the received decision shows that in case of a persistence in time of coefficient of Poisson of the environment, creep doesn't influence tension, and only affects deformation or relocation (settling that corresponds to earlier set provisions. In case of a persistence of coefficient of Poisson the intense deformed status of the environment can be determined also by method of elastic analogy, solving the appropriate uprugomgnovenny problem. The solution of the equation for pore pressure is executed by Fourier method. According to the received analytical decision the flowchart and the program in Matlab packet with use of the built-in programming language of the Matlab system is made.Conclusion. For two options of conditions of drainage calculation of function of pore pressure, function of a side raspor and level of consolidation of a layer taking into account and without creep is executed and their surfaces of distribution and a graphics of change are constructed.

  13. Spatial-phase code-division multiple-access system with multiplexed Fourier holography switching for reconfigurable optical interconnection.

    Science.gov (United States)

    Takasago, K; Takekawa, M; Shirakawa, A; Kannari, F

    2000-05-10

    A new, to our knowledge, space-variant optical interconnection system based on a spatial-phase code-division multiple-access technique with multiplexed Fourier holography is described. In this technique a signal beam is spread over wide spatial frequencies by an M-sequence pseudorandom phase code. At a receiver side a selected signal beam is properly decoded, and at the same time its spatial pattern is shaped with a Fourier hologram, which is recorded by light that is encoded with the same M-sequence phase mask as the desired signal beam and by light whose spatial beam pattern is shaped to a signal routing pattern. Using the multiplexed holography, we can simultaneously route multisignal flows into individually specified receiver elements. The routing pattern can also be varied by means of switching the encoding phase code or replacing the hologram. We demonstrated a proof-of-principle experiment with a doubly multiplexed hologram that enables simultaneous routing of two signal beams. Using a numerical model, we showed that the proposed scheme can manage more than 250 routing patterns for one signal flow with one multiplexed hologram at a signal-to-noise ratio of ~5.

  14. Four-fold increase in users of time-wavelength division multiplexing (TWDM) passive optical network (PON) by delayed optical amplitude modulation (AM) upstream

    Science.gov (United States)

    Kachhatiya, Vivek; Prince, Shanthi

    2016-12-01

    In this paper, we have proposed and simulated optical time division multiplexed passive optical network (TDM-PON) using delayed optical amplitude modulation (AM). Eight upstream wavelengths are demonstrated to show optical time wavelength division multiplexed (TWDM) by combining optical network units (ONU) users data at the remote node (RN). Each ONU generates 2.5 Gb/s user data, and it is modulated using novel return to zero (RZ) delayed AM. Optical TDM aggregates 10 Gb/s data per wavelength from four 2.5 Gb/s upstream user data, which facilitates four different ONU data on the same wavelength as 10 Gb/s per upstream wavelength and, simplify the laser requirements (2.5 Gb/s) at each optical network unit (ONU) transmitter. Upstream optical TWDM-PON is investigated for eight wavelengths with wavelength spacing of 100 GHz. Novel optical TDM for upstream increased the number of the simultaneous user to fourfold from conventional TWDM-PON using delayed AM with a high-quality-factor of received signal. Despite performance degradation due to different fiber reach and dispersion compensation technique, Optical TWDM link shows significant improvement regarding receiver sensitivity when compared with common TWDM link. Hence, it offers optimistic thinking to show optical TDM at this phase as one of the future direction, where complex digital signal processing (DSP) and coherent optical communication are frequently demonstrated to serve the access network. Downstream side conventional TWDM eight wavelengths are multiplexed at the OLT and sent downstream to serve distributed tunable ONU receivers through an optical distribution network (ODN). Each downstream wavelengths are modulated at the peak rate of 10 Gb/s using non-return to zero external modulation (NRZ-EM). The proposed architecture is cost efficient and supports high data rates as well as ;pay as you grow; network for both service providers and the users perspectives. Users are classified into two categories viz home

  15. Three-Phase Time-Multiplexed Planar Power Transmission to Distributed Implants.

    Science.gov (United States)

    Lee, Byunghun; Ahn, Dukju; Ghovanloo, Maysam

    2016-03-01

    A platform has been presented for wireless powering of receivers (Rx's) that are arbitrarily distributed over a large area. A potential application could be powering of small Rx implants, distributed over large areas of the brain. The transmitter (Tx) consists of three overlapping layers of hexagonal planar spiral coils (hex-PSC) that are horizontally shifted to provide the strongest and most homogeneous electromagnetic flux coverage. The three-layer hex-PSC array is driven by a three-phase time-division-multiplexed power Tx that takes the advantage of the carrier phase shift, coil geometries, and Rx time constant to homogeneously power the arbitrarily distributed Rx's regardless of their misalignments. The functionality of the proposed three-phase power transmission concept has been verified in a detailed scaled-up high-frequency structure simulator Advanced Design System simulation model and measurement setup, and compared with a conventional Tx. The new Tx delivers 5.4 mW to each Rx and achieves, on average, 5.8% power transfer efficiency to the Rx at the worst case 90° angular misalignment, compared with 1.4% by the conventional Tx.

  16. Fourier optics analysis of phase-mask-based path-length-multiplexed optical coherence tomography.

    Science.gov (United States)

    Yin, Biwei; Dwelle, Jordan; Wang, Bingqing; Wang, Tianyi; Feldman, Marc D; Rylander, Henry G; Milner, Thomas E

    2015-11-01

    Optical coherence tomography (OCT) is an imaging technique that constructs a depth-resolved image by measuring the optical path-length difference between broadband light backscattered from a sample and a reference surface. For many OCT sample arm optical configurations, sample illumination and backscattered light detection share a common path. When a phase mask is placed in the sample path, features in the detected signal are observed, which suggests that an analysis of a generic common path OCT imaging system is warranted. In this study, we present a Fourier optics analysis using a Fresnel diffraction approximation of an OCT system with a path-length-multiplexing element (PME) inserted in the sample arm optics. The analysis may be generalized for most phase-mask-based OCT systems. A radial-angle-diverse PME is analyzed in detail, and the point spread function, coherent transfer function, sensitivity of backscattering angular diversity detection, and signal formation in terms of sample spatial frequency are simulated and discussed. The analysis reveals important imaging features and application limitations of OCT imaging systems with a phase mask in the sample path optics.

  17. Phase modulation pseudocolor encoding ghost imaging

    Institute of Scientific and Technical Information of China (English)

    段德洋; 张路; 杜少将; 夏云杰

    2015-01-01

    We present a ghost imaging scheme that can obtain a good pseudocolor image of black-and-white objects. The essential idea is to use the multi-wavelength thermal light source and the phase modulation pseudocolor encoding technique, which overcomes the disadvantages of other methods involved the spatial filtering. Therefore, the pseudocolor ghost image achieved by this imaging scheme is better than that obtained by other methods in brightness, color, and signal-to-noise ratio.

  18. Simultaneous amplitude and phase modulation by a discrete phase-only filter.

    Science.gov (United States)

    Goto, Hiroomi; Konishi, Tsuyoshi; Itoh, Kazuyoshi

    2009-03-01

    We propose a simultaneous amplitude and phase modulation method by a discrete phase-only filter. The proposed amplitude-phase filter can be realized by a discrete phase modulation of the diffractive optical element as well as a continuous phase modulation of the liquid crystal spatial light modulator. The fabricated amplitude-phase filter that has the six phase modulation levels shows a transfer efficiency of 75% regardless of the polarization state of the incident light. By using the proposed amplitude-phase filter, we demonstrate a temporal waveform conversion from sech(2) to super-Gaussian, which requires both amplitude and phase modulations.

  19. Monodomain Blue Phase Liquid Crystal Layers for Phase Modulation

    Science.gov (United States)

    Oton, E.; Netter, E.; Nakano, T.; D.-Katayama, Y.; Inoue, F.

    2017-03-01

    Liquid crystal “Blue Phases” (BP) have evolved, in the last years, from a scientific curiosity to emerging materials for new photonic and display applications. They possess attractive features over standard nematic liquid crystals, like submillisecond switching times and polarization- independent optical response. However, BPs still present a number of technical issues that prevent their use in practical applications: their phases are only found in limited temperature ranges, thus requiring stabilization of the layers; stabilized BP layers are inhomogeneous and not uniformly oriented, which worsen the optical performance of the devices. It would be essential for practical uses to obtain perfectly aligned and oriented monodomain BP layers, where the alignment and orientation of the cubic lattice are organized in a single 3D structure. In this work we have obtained virtually perfect monodomain BP layers and used them in devices for polarization independent phase modulation. We demonstrate that, under applied voltage, well aligned and oriented layers generate smoother and higher values of the phase shift than inhomogeneous layers, while preserving polarization independency. All BP devices were successfully stabilized in BPI phase, maintaining the layer monodomain homogeneity at room temperature, covering the entire area of the devices with a unique BP phase.

  20. Monodomain Blue Phase Liquid Crystal Layers for Phase Modulation

    Science.gov (United States)

    Oton, E.; Netter, E.; Nakano, T.; D.-Katayama, Y.; Inoue, F.

    2017-01-01

    Liquid crystal “Blue Phases” (BP) have evolved, in the last years, from a scientific curiosity to emerging materials for new photonic and display applications. They possess attractive features over standard nematic liquid crystals, like submillisecond switching times and polarization- independent optical response. However, BPs still present a number of technical issues that prevent their use in practical applications: their phases are only found in limited temperature ranges, thus requiring stabilization of the layers; stabilized BP layers are inhomogeneous and not uniformly oriented, which worsen the optical performance of the devices. It would be essential for practical uses to obtain perfectly aligned and oriented monodomain BP layers, where the alignment and orientation of the cubic lattice are organized in a single 3D structure. In this work we have obtained virtually perfect monodomain BP layers and used them in devices for polarization independent phase modulation. We demonstrate that, under applied voltage, well aligned and oriented layers generate smoother and higher values of the phase shift than inhomogeneous layers, while preserving polarization independency. All BP devices were successfully stabilized in BPI phase, maintaining the layer monodomain homogeneity at room temperature, covering the entire area of the devices with a unique BP phase. PMID:28281691

  1. Plastering. Pre-Apprenticeship Phase 2 Training. Student Training Modules.

    Science.gov (United States)

    Hamblen, Ron

    These 20 Student Training Modules on plastering comprise one of nine sets of self-paced learning modules developed for Pre-Apprenticeship Phase 2 Training. (A companion instructor's guide is available separately as CE 031 569.) The modules are designed to impart trade knowledge and skills to the student. Each module contains some or all of the…

  2. Phase-modulation transmission system for quantum cryptography.

    Science.gov (United States)

    Mérolla, J M; Mazurenko, Y; Goedgebuer, J P; Porte, H; Rhodes, W T

    1999-01-15

    We describe a new method for quantum key distribution that utilizes phase modulation of sidebands of modulation by use of integrated electro-optic modulators at the transmitting and receiving modules. The system is shown to produce constructive or destructive interference with unity visibility, which should allow quantum cryptography to be carried out with high flexibility by use of conventional devices.

  3. Reconfigurable intensity modulation and direct detection optical transceivers for variable-rate wavelength-division-multiplexing passive optical networks utilizing digital signal processing-based symbol mapper

    Science.gov (United States)

    Zhang, Zhiguo; Zhang, Bingbing; Chen, Yanxu; Chen, Xue

    2017-01-01

    Variable-rate intensity modulation and direct detection-based optical transceivers with software-controllable reconfigurability and transmission performance adaptability are experimentally demonstrated, utilizing M-QAM symbol mapping implemented in MATLAB® programs. A frequency division multiplexing-based symbol demapping and wavelength management method is proposed for the symbol demapper and tunable laser management used in colorless optical network unit.

  4. Simultaneous determination of nitrite and nitrate ions by air-segmented amplitude-modulated multiplexed flow analysis.

    Science.gov (United States)

    Yoshida, Haruka; Inui, Koji; Takeuchi, Masaki; Tanaka, Hideji

    2012-01-01

    The concept of amplitude-modulated multiplexed flow analysis has been extended to the simultaneous determination of multiple analytes in a sample. A sample solution containing nitrite and nitrate ions is delivered from two channels, but the flow rates are varied at different frequencies. One of the channels has a reduction column for converting nitrate ions to nitrite ions. Downstream, the absorbance of the diazo-coupling product is monitored after the merging of both solutions with a Griess reagent. The signal is analyzed by a fast Fourier transform (FFT) in real time. From the thus-obtained amplitude, a µmol dm(-3) level of the ions can be determined. The introduction of air bubbles is effective to reduce any axial dispersion, and hence to improve the sensitivity.

  5. Multiple-image encryption by space multiplexing based on compressive sensing and the double-random phase-encoding technique.

    Science.gov (United States)

    Deepan, B; Quan, C; Wang, Y; Tay, C J

    2014-07-10

    In this paper, a new multiple-image encryption and decryption technique that utilizes the compressive sensing (CS) concept along with a double-random phase encryption (DRPE) has been proposed. The space multiplexing method is employed for integrating multiple-image data. The method, which results in a nonlinear encryption system, is able to overcome the vulnerability of classical DRPE. The CS technique and space multiplexing are able to provide additional key space in the proposed method. A numerical experiment of the proposed method is implemented and the results show that the proposed method has good accuracy and is more robust than classical DRPE. The proposed system is also employed against chosen-plaintext attacks and it is found that the inclusion of compressive sensing enhances robustness against the attacks.

  6. Multiple-image encryption based on interference principle and phase-only mask multiplexing in Fresnel transform domain.

    Science.gov (United States)

    Wang, Qu; Guo, Qing; Lei, Liang; Zhou, Jinyun

    2013-10-01

    In this article, a multiple-image encryption method based on the optical interference principle and phase-only mask (POM) multiplexing is proposed. During the encryption process, each secret image is encoded into two analytically obtained POMs and one computer-generated random POM, in which no iterative computation is required. The analytically obtained POMs taken from different secret images are then synthesized by POM multiplexing and further encoded into two complex ciphertext images. The silhouette problem that exists in the earlier interference principle-based encryption approaches is totally resolved by the proposal. Both digital and optical means can be used for decryption. The crosstalk effect between the secret images will not appear in the decrypted results by using the proposed system. Numerical simulations have been given to verify the performance and feasibility of the proposal. We also discuss briefly the influence of information compression on the quality of decrypted images.

  7. Qualitative Analysis of Self Phase Modulation (SPM

    Directory of Open Access Journals (Sweden)

    Ruby Verma

    2013-03-01

    Full Text Available Optical fiber changed the way of communication. In comparison with wireless communication, optical fiber communication is very fast and reliable. It is more secure but costly. Optical fiber uses the principle of total internal reflection for transmission. Optical fiber has core and cladding with different refractive index and major portion of the signal goes through the core. But due macro and micro bending, chromatic dispersion is observed.In this paper, we have analyzed self phase modulation in an optical fiber system and discussed how it causes dispersion in input signal. These effects are simulated using OPTISYSTEM tool at a bit rate of 10Gbps and analysed using eye pattern method with respect to bit error rate and Q factor. Simulation results from the OPTISYSTEM tool are also compared with the numerical analysis of nonlinear Schrodinger equation, which is simulated in MATLAB

  8. Vector Modulator for Phase Shifting in Passive Beamforming Wireless Systems

    Directory of Open Access Journals (Sweden)

    P.Sampath,

    2010-05-01

    Full Text Available This paper proposes vector modulator for changing the phase of a signal in passive beamforming system. Vector modulator is used to perform a phase shift function with added benefit of amplitude control. It is used to improve the directivity of RF waves in Wireless systems. Vector modulator is implemented for a center frequency of 902.5 MHz. The simulation is performed for individual blocks of the vector modulator and for vector modulator with JFET and MOSFET as controlling device in the variable attenuator of the vector modulator.

  9. Modulation efficiency of double-phase hologram complex light modulation macro-pixels.

    Science.gov (United States)

    Choi, Sujin; Roh, Jinyoung; Song, Hoong; Sung, Geeyoung; An, Jungkwuen; Seo, Wontaek; Won, Kanghee; Ungnapatanin, Jesada; Jung, Myounghoon; Yoon, Yongzoon; Lee, Hong-Seok; Oh, Chang-Hyun; Hahn, Joonku; Kim, Hwi

    2014-09-01

    The modulation efficiency of the double-phase hologram macro-pixel that is designed for complex modulation of light waves is defined and analyzed. The scale-down of the double-phase hologram macro-pixel associated with the construction of complex spatial light modulators is discussed.

  10. Aqueous two-phase system patterning of detection antibody solutions for cross-reaction-free multiplex ELISA

    Science.gov (United States)

    Frampton, John P.; White, Joshua B.; Simon, Arlyne B.; Tsuei, Michael; Paczesny, Sophie; Takayama, Shuichi

    2014-05-01

    Accurate disease diagnosis, patient stratification and biomarker validation require the analysis of multiple biomarkers. This paper describes cross-reactivity-free multiplexing of enzyme-linked immunosorbent assays (ELISAs) using aqueous two-phase systems (ATPSs) to confine detection antibodies at specific locations in fully aqueous environments. Antibody cross-reactions are eliminated because the detection antibody solutions are co-localized only to corresponding surface-immobilized capture antibody spots. This multiplexing technique is validated using plasma samples from allogeneic bone marrow recipients. Patients with acute graft versus host disease (GVHD), a common and serious condition associated with allogeneic bone marrow transplantation, display higher mean concentrations for four multiplexed biomarkers (HGF, elafin, ST2 and TNFR1) relative to healthy donors and transplant patients without GVHD. The antibody co-localization capability of this technology is particularly useful when using inherently cross-reactive reagents such as polyclonal antibodies, although monoclonal antibody cross-reactivity can also be reduced. Because ATPS-ELISA adapts readily available antibody reagents, plate materials and detection instruments, it should be easily transferable into other research and clinical settings.

  11. Device Length Dependency of Cross Gain Modulation and Cross Phase Modulation in Semiconductor Optical Amplifier

    Institute of Scientific and Technical Information of China (English)

    Tomonori; Yazaki; Ryo; Inohara; Kosuke; Nishimura; Munefumi; Tsurusawa; Masashi; Usami

    2003-01-01

    The cross gain modulation, the cross phase modulation and their recovery time in the SOAs with the various lengths were experimentally investigated. It was found that these values strongly depended on the device length.

  12. XPM-induced degradation of multilevel phase modulated channel caused by neighboring NRZ modulated channels

    DEFF Research Database (Denmark)

    Jensen, Jesper Bevensee; Schiellerup, G.; Peucheret, Christophe

    2008-01-01

    The impact of XPM from NRZ modulated channels on an 8-level phase modulated channel in a WDM system was investigated. Requirements on launch power are found. 400 km transmission was achieved with negligible penalty.......The impact of XPM from NRZ modulated channels on an 8-level phase modulated channel in a WDM system was investigated. Requirements on launch power are found. 400 km transmission was achieved with negligible penalty....

  13. Wavelength conversion based on cross-phase modulation in a semiconductor Mach-Zehnder modulator

    DEFF Research Database (Denmark)

    Liu, Fenghai; Zheng, Xueyan; Oxenløwe, Leif Katsuo

    2001-01-01

    Wavelength conversion based on cross-phase modulation in a reversely biased semiconductor Mach-Zehnder modulator is proposed and successfully demonstrated in a commercial device. The converted signals exhibit extinction ratio >13 dB and penalty......Wavelength conversion based on cross-phase modulation in a reversely biased semiconductor Mach-Zehnder modulator is proposed and successfully demonstrated in a commercial device. The converted signals exhibit extinction ratio >13 dB and penalty...

  14. Robust quantum data locking from phase modulation

    Science.gov (United States)

    Lupo, Cosmo; Wilde, Mark M.; Lloyd, Seth

    2014-08-01

    Quantum data locking is a uniquely quantum phenomenon that allows a relatively short key of constant size to (un)lock an arbitrarily long message encoded in a quantum state, in such a way that an eavesdropper who measures the state but does not know the key has essentially no information about the message. The application of quantum data locking in cryptography would allow one to overcome the limitations of the one-time pad encryption, which requires the key to have the same length as the message. However, it is known that the strength of quantum data locking is also its Achilles heel, as the leakage of a few bits of the key or the message may in principle allow the eavesdropper to unlock a disproportionate amount of information. In this paper we show that there exist quantum data locking schemes that can be made robust against information leakage by increasing the length of the key by a proportionate amount. This implies that a constant size key can still lock an arbitrarily long message as long as a fraction of it remains secret to the eavesdropper. Moreover, we greatly simplify the structure of the protocol by proving that phase modulation suffices to generate strong locking schemes, paving the way to optical experimental realizations. Also, we show that successful data locking protocols can be constructed using random code words, which very well could be helpful in discovering random codes for data locking over noisy quantum channels.

  15. Phase-only spatial light modulation by the reverse phase contrast method

    DEFF Research Database (Denmark)

    Glückstad, J.; Mogensen, P.C.; Eriksen, R.L.

    2002-01-01

    A new approach to phase-only spatial light modulation is proposed in which a given amplitude pattern can be converted into a spatially identical binary phase pattern. A spatial filtering approach is applied to transform spatial amplitude modulation into spatial phase modulation using the Reverse...... Phase Contrast (RPC) method. The analytical method for achieving this is outlined and experimental results are shown for the generation of a binary phase-only distribution using an amplitude spatial light modulator and a phase-only spatial filter....

  16. Fiber Ring Laser In-cavity Phase Modulation

    Institute of Scientific and Technical Information of China (English)

    YU Benli; QIAN Jingren; LUO Jiatong; YANG Yinghai

    2001-01-01

    In this paper, experimental results of the in-cavity phase modulation induced by dithering PZT is reported. The dithering PZT can produce strong phase modulation, reshaping the laser output spectrum, but does not affect the laser linewidth, which is measured by homodyne method.

  17. WDM Phase-Modulated Millimeter-Wave Fiber Systems

    DEFF Research Database (Denmark)

    Yu, Xianbin; Prince, Kamau; Gibbon, Timothy Braidwood

    2012-01-01

    This chapter presents a computer simulation case study of two typical WDM phase-modulated millimeter-wave systems. The phase-modulated 60 GHz fiber multi-channel transmission systems employ single sideband (SSB) and double sideband subcarrier modulation (DSB-SC) schemes and present one of the lat......This chapter presents a computer simulation case study of two typical WDM phase-modulated millimeter-wave systems. The phase-modulated 60 GHz fiber multi-channel transmission systems employ single sideband (SSB) and double sideband subcarrier modulation (DSB-SC) schemes and present one...... of the latest research efforts in the rapidly emerging Radio-over-Fiber (RoF) application space for in-house access networks....

  18. Phase-modulating lasers toward on-chip integration.

    Science.gov (United States)

    Kurosaka, Yoshitaka; Hirose, Kazuyoshi; Sugiyama, Takahiro; Takiguchi, Yu; Nomoto, Yoshiro

    2016-07-26

    Controlling laser-beam patterns is indispensable in modern technology, where lasers are typically combined with phase-modulating elements such as diffractive optical elements or spatial light modulators. However, the combination of separate elements is not only a challenge for on-chip miniaturisation but also hinders their integration permitting the switchable control of individual modules. Here, we demonstrate the operation of phase-modulating lasers that emit arbitrarily configurable beam patterns without requiring any optical elements or scanning devices. We introduce a phase-modulating resonator in a semiconductor laser, which allows the concurrent realisation of lasing and phase modulation. The fabricated devices are on-chip-sized, making them suitable for integration. We believe this work will provide a breakthrough in various laser applications such as switchable illumination patterns for bio-medical applications, structured illuminations, and even real three-dimensional or highly realistic displays, which cannot be realised with simple combinations of conventional devices or elements.

  19. Experimental 2.5-Gb/s QPSK WDM phase-modulated radio-over-fiber link with digital demodulation by a K-means algorithm

    DEFF Research Database (Denmark)

    Guerrero Gonzalez, Neil; Zibar, Darko; Caballero Jambrina, Antonio;

    2010-01-01

    Highest reported bit rate of 2.5 Gb/s for optically phase modulated radio-over-fiber (RoF) link, employing digital coherent detection, is demonstrated. Demodulation of 3$,times,$ 2.5 Gb/s quadrature phase-shift keying modulated wavelength-division-multiplexed RoF channels is achieved after 79 km ...... of transmission through deployed fiber. Error-free performance (bit-error rate corresponding to $10^{{-}4}$) is achieved using a digital coherent receiver in combination with a $K$-means algorithm for radio-frequency phase recovery....

  20. Experimental 2.5-Gb/s QPSK WDM phase-modulated radio-over-fiber link with digital demodulation by a K-means algorithm

    DEFF Research Database (Denmark)

    Guerrero Gonzalez, Neil; Zibar, Darko; Caballero Jambrina, Antonio

    2010-01-01

    Highest reported bit rate of 2.5 Gb/s for optically phase modulated radio-over-fiber (RoF) link, employing digital coherent detection, is demonstrated. Demodulation of 3$,times,$ 2.5 Gb/s quadrature phase-shift keying modulated wavelength-division-multiplexed RoF channels is achieved after 79 km...... of transmission through deployed fiber. Error-free performance (bit-error rate corresponding to $10^{{-}4}$) is achieved using a digital coherent receiver in combination with a $K$-means algorithm for radio-frequency phase recovery....

  1. Using multiplexed regulation of luciferase activity and GFP translocation to screen for FOXO modulators

    Directory of Open Access Journals (Sweden)

    Carnero Amancio

    2009-02-01

    Full Text Available Abstract Background Independent luciferase reporter assays and fluorescent translocation assays have been successfully used in drug discovery for several molecular targets. We developed U2transLUC, an assay system in which luciferase and fluorescent read-outs can be multiplexed to provide a powerful cell-based high content screening method. Results The U2transLUC system is based on a stable cell line expressing a GFP-tagged FOXO transcription factor and a luciferase reporter gene under the control of human FOXO-responsive enhancers. The U2transLUC assay measures nuclear-cytoplasmic FOXO shuttling and FOXO-driven transcription, providing a means to analyze these two key features of FOXO regulation in the same experiment. We challenged the U2transLUC system with chemical probes with known biological activities and we were able to identify compounds with translocation and/or transactivation capacity. Conclusion Combining different biological read-outs in a single cell line offers significant advantages over conventional cell-based assays. The U2transLUC assay facilitates the maintenance and monitoring of homogeneous FOXO transcription factor expression and allows the reporter gene activity measured to be normalized with respect to cell viability. U2transLUC is suitable for high throughput screening and can identify small molecules that interfere with FOXO signaling at different levels.

  2. 1.25-3.125 Gb/s per user PON with RSOA as phase modulator for statistical wavelength ONU

    Science.gov (United States)

    Chu, Guang Yong; Polo, Victor; Lerín, Adolfo; Tabares, Jeison; Cano, Iván N.; Prat, Josep

    2015-12-01

    We report a new scheme to support, cost efficiently, ultra-dense wavelength division multiplexing (UDWDM) for optical access networks. As validating experiment, we apply phase modulation of a reflective semiconductor optical amplifier (RSOA) at the ONU with a single DFB, and simplified coherent receiver at OLT for upstream. We extend the limited 3-dB modulation bandwidth of available uncooled To-can packaged RSOA (~400 MHz) and operate it at 3.125 Gb/s with the optimal performance for phase modulation using small and large signal measurement characteristics. The optimal condition is selected at input power of 0 dBm, with 70 mA bias condition. The sensitivities at 3.125 Gb/s (at BER=10-3) for heterodyne and intradyne detection reach -34.3 dBm and -38.8 dBm, respectively.

  3. Coherent Population Trapping Induced by Phase Modulated and Fluctuating Fields

    Institute of Scientific and Technical Information of China (English)

    WANG Jian; HU Xiang-Ming

    2007-01-01

    We examine the effects of cross correlated phase fluctuations on the coherent population trapping (CPT) induced by a pair of phase-modulated fields with equal modulation frequencies in a three-level A system. The maximal coherence of -0.5, which appears when CPT occurs for equal modulation indices, is preserved in the presence of the critically cross-correlated fluctuations. Unexpectedly, the non-maximal coherence, which is established when CPT is obtained for different modulation indices, is significantly enhanced due to the critically cross-correlated fluctuations.

  4. Highly birefringent crystal for Raman transitions with phase modulators

    Science.gov (United States)

    Arias, Nieves; Abediyeh, Vahide; Hamzeloui, Saeed; Jeronimo-Moreno, Yasser; Gomez, Eduardo

    2016-05-01

    We present a system to excite Raman transitions with minimum phase noise. The system uses a phase modulator to generate the phase locked beams required for the transition. We use a long calcite crystal to filter out one of the sidebands, avoiding the cancellation that appears at high detunings for phase modulation. The measured phase noise is limited by the quality of the microwave synthesizer. We use the calcite crystal a second time to produce a co-propagating Raman pair with perpendicular polarizations to drive velocity insensitive Raman transitions. Support from CONACYT and Fundacion Marcos Moshinsky.

  5. InGaAsP/InP DH Ridge Waveguide Phase Modulator with High Modulation Efficiency

    Institute of Scientific and Technical Information of China (English)

    Young; Tae; Byun; Hwa; Sun; Park; Sung; Jin; Kim; Deok; Ha; Woo; Jong; Chang; Yi; Yoshiaki; Nakano

    2003-01-01

    The P-p-n-N InGaAsP/InP ridge waveguide phase modulator has been fabricated and investigated at a wavelength of 1550nm. The phase modulation efficiency measured by the Fabry-Perot resonance method is as high as 34°/V·mm for TE mode. The QEO effect becomes dominant from - 4V to - 8V.

  6. InGaAsP/InP DH Ridge Waveguide Phase Modulator with High Modulation Efficiency

    Institute of Scientific and Technical Information of China (English)

    Young Tae Byun; Hwa Sun Park; Sung Jin Kim; Deok Ha Woo; Jong Chang Yi; Yoshiaki Nakano

    2003-01-01

    The P-p-n-N InGaAsP/InP ridge waveguide phase modulator has been fabricated and investigated at a wavelength of 1550nm. The phase modulation efficiency measured by the Fabry-Perot resonance method is as high as 34°/V.mm for TE mode. The QEO effect becomes dominant from -4V to -8V.

  7. Open-Loop Wide-Bandwidth Phase Modulation Techniques

    Directory of Open Access Journals (Sweden)

    Nitin Nidhi

    2011-01-01

    Full Text Available The ever-increasing growth in the bandwidth of wireless communication channels requires the transmitter to be wide-bandwidth and power-efficient. Polar and outphasing transmitter topologies are two promising candidates for such applications, in future. Both these architectures require a wide-bandwidth phase modulator. Open-loop phase modulation presents a viable solution for achieving wide-bandwidth operation. An overview of prior art and recent approaches for phase modulation is presented in this paper. Phase quantization noise cancellation was recently introduced to lower the out-of-band noise in a digital phase modulator. A detailed analysis on the impact of timing and quantization of the cancellation signal is presented. Noise generated by the transmitter in the receive band frequency poses another challenge for wide-bandwidth transmitter design. Addition of a noise transfer function notch, in a digital phase modulator, to reduce the noise in the receive band during phase modulation is described in this paper.

  8. Digital image multiplexing/demultiplexing method using spatial spectral diffusion and virtual phase conjugation technique for reduction of dynamic range consumption in holographic medium

    Science.gov (United States)

    Goto, Yuta; Okamoto, Atsushi; Takabayashi, Masanori; Ogawa, Kazuhisa; Tomita, Akihisa

    2017-09-01

    The recording density in holographic data storage (HDS) systems is determined by the dynamic range of the recording medium. If a hologram is recorded with a small exposure, the consumption amount of the dynamic range per hologram is reduced, and the recording density can be improved. In this report, we propose a digital image multiplexing/demultiplexing method using spatial spectral diffusion and a virtual phase conjugation technique to reduce the consumption amount of the dynamic range in a recording medium. In our method, multiple signals are simultaneously recorded in a medium by multiplexing those signals using a beam combiner before recording, unlike the general multiplexing method of HDS. Then, each original signal can be reproduced independently by utilizing the property of a random diffuser and a phase-conjugated light. In the simulation, we confirmed that our method can improve the recording density because the consumption of the dynamic range is reduced.

  9. Uncovering introductory astronomy students' conceptual modules of lunar phases

    Science.gov (United States)

    Lindell, Rebecca; Traxler, Adrienne

    2017-01-01

    Brewe, Bruun and Bearden developed Module Analysis of Multiple Choice Responses (MAMCR) methodology for using network analysis to uncover the underlying conceptual modules of student performance on multiple-choice assessments. The Lunar Phases Concept Inventory (LPCI) assesses students understanding of lunar phases across 8 separate dimensions of understanding based on the results of a detailed qualitative phenomenology of college students' understanding of lunar phases. Unlike many concept inventories, the LPCI has multiple items for each dimension of understanding and each response corresponds to either the scientifically correct answer or to an alternative idea uncovered from the qualitative investigation. In this study, we have combined MAMCR with the database of nearly 2000 LPCI pre-test results. We will report on the preliminary different conceptual modules of lunar phases and the relationship of these modules to previous qualitative research.

  10. All-optical phase modulation for integrated interferometric biosensors.

    Science.gov (United States)

    Dante, Stefania; Duval, Daphné; Sepúlveda, Borja; González-Guerrero, Ana Belen; Sendra, José Ramón; Lechuga, Laura M

    2012-03-26

    We present the theoretical and the experimental implementation of an all-optical phase modulation system in integrated Mach-Zehnder Interferometers to solve the drawbacks related to the periodic nature of the interferometric signal. Sensor phase is tuned by modulating the emission wavelength of low-cost commercial laser diodes by changing their output power. FFT deconvolution of the signal allows for direct phase readout, immune to sensitivity variations and to light intensity fluctuations. This simple phase modulation scheme increases the signal-to-noise ratio of the measurements in one order of magnitude, rendering in a sensor with a detection limit of 1.9·10⁻⁷ RIU. The viability of the all-optical modulation approach is demonstrated with an immunoassay detection as a biosensing proof of concept.

  11. Terahertz cross-phase modulation of an optical mode

    DEFF Research Database (Denmark)

    Lavrinenko, Andrei; Novitsky, Andrey; Zalkovskij, Maksim

    2013-01-01

    We discuss an optical scheme which facilitates modulation of an optical waveguide mode by metallic-nanoslit-enhanced THz radiation. The waveguide mode acquires an additional phase shift due to THz nonlinearity with fields reachable in experiments.......We discuss an optical scheme which facilitates modulation of an optical waveguide mode by metallic-nanoslit-enhanced THz radiation. The waveguide mode acquires an additional phase shift due to THz nonlinearity with fields reachable in experiments....

  12. Tunable dispersion compensation using phase modulation in receiver part

    DEFF Research Database (Denmark)

    Siahlo, Andrei; Clausen, Anders; Oxenløwe, Leif Katsuo

    2004-01-01

    A novel method of tuneable dispersion compensation at which phase modulation is applied in the receiver part is proposed for OTDM systems. Compensation of dispersion of 3.2 ps/nm at 160 Gb/s OTDM transmission is demonstrated.......A novel method of tuneable dispersion compensation at which phase modulation is applied in the receiver part is proposed for OTDM systems. Compensation of dispersion of 3.2 ps/nm at 160 Gb/s OTDM transmission is demonstrated....

  13. Method to measure the phase modulation characteristics of a liquid crystal spatial light modulator.

    Science.gov (United States)

    Wu, Yunlong; Nie, Jinsong; Shao, Li

    2016-11-01

    The universal liquid crystal spatial light modulator (LC-SLM) is widely used in many aspects of optical studies. The working principles and applications of LC-SLM were introduced briefly. The traditional Twyman-Green interference method, which was used to measure the phase modulation characteristics of a liquid spatial light modulator, had some obvious disadvantages in practice. To avoid these issues, the traditional Twyman-Green interference method was improved. Also, a new method to process interference fringes and measure the shift distances and cycles automatically by computers was proposed. The phase modulation characteristics of P512-1064 LC-SLM produced by the Meadowlark Company were measured to verify the validity of the newly proposed method. In addition, in order to compensate and correct the nonlinear characteristics of the phase modulation curve, three universal inverse interpolation methods were utilized. The root mean squared error and residual sum of squares between the calibrated phase modulation curve and the ideal phase modulation curve were reduced obviously by taking advantage of the inverse interpolation methods. Subsequently, the method of shape-preserving subsection cubic interpolation had acquired the best performance with high computation efficiency. Experiments have been performed to verify the validity of the interpolation method. The experimental results showed that the phase modulation characteristics of LC-LSM could be acquired and calibrated automatically with convenience and high efficiency by utilizing the newly proposed processing method.

  14. Evaluation of Modulation Schemes for Three-Phase to Three-Phase Matrix Converters

    DEFF Research Database (Denmark)

    Helle, Lars; Larsen, Kim B.; Joergensen, Allan Holm

    2004-01-01

    This paper presents a method for evaluating different modulation schemes employed with three-phase to three-phase matrix converters. The evaluation method addresses three important modulator characteristics: the output waveform quality, the input waveform quality and the switching losses associated...... on the output load angle. This new modulation approach is applicable whenever the output voltage reference is below half the input voltage, and the output voltage quality is then superior to that of the conventional space vector modulation scheme. The functionality of the new modulation scheme is validated...

  15. Considerations of digital phase modulation for narrowband satellite mobile communication

    Science.gov (United States)

    Grythe, Knut

    1990-01-01

    The Inmarsat-M system for mobile satellite communication is specified as a frequency division multiple access (FDMA) system, applying Offset Quadrature Phase Shift Keying (QPSK) for transmitting 8 kbit/sec in 10 kHz user channel bandwidth. We consider Digital Phase Modulation (DPM) as an alternative modulation format for INMARSAT-M. DPM is similar to Continuous Phase Modulation (CPM) except that DPM has a finite memory in the premodular filter with a continuous varying modulation index. It is shown that DPM with 64 states in the VA obtains a lower bit error rate (BER). Results for a 5 kHz system, with the same 8 kbit/sec transmitted bitstream, is also presented.

  16. The effect of input phase modulation to a phase-sensitive optical amplifier

    CERN Document Server

    Li, Tian; Horrom, Travis; Jones, Kevin M; Lett, Paul D

    2016-01-01

    Many optical applications depend on amplitude modulating optical beams using devices such as acousto-optical modulators (AOMs) or optical choppers. Methods to add amplitude modulation (AM) often inadvertently impart phase modulation (PM) onto the light as well. While this PM is of no consequence to many phase-insensitive applications, phase-sensitive processes can be affected. Here we study the effects of input phase and amplitude modulation on the output of a quantum-noise limited phase-sensitive optical amplifier (PSA) realized in hot $^{85}$Rb vapor. We investigate the dependence of PM on AOM alignment and demonstrate a novel approach to quantifying PM by using the PSA as a diagnostic tool. We then use this method to measure the alignment-dependent PM of an optical chopper which arises due to diffraction effects as the chopper blade passes through the optical beam.

  17. Digital Monopulse Receivers for Phase Modulated Signals

    Science.gov (United States)

    2005-04-14

    Mateo Burgos-García, Gema Ferreiro-Collar, Alberto Asensio Ló Grupo de Microondas y Dpto. Señales, Sistemas y Radio E.T.S.I. Telecomunic Universidad...Politécnica d Ciudad Universitaria 28040 Madrid, Spa Email: mateo@gmr.ssr. Digital Monopulse Rec Modulated Si T ∆ Σ Z1(t) Z2(t)log-amplifier of each...Microondas y Radar Dpto. Señales, Sistemas y Radiocomunicaciones E.T.S.I. Telecomunicación Universidad Politécnica de Madrid Ciudad Universitaria s/n

  18. Optimal space communication techniques. [a discussion of delta modulation, pulse code modulation, and phase locked systems

    Science.gov (United States)

    Schilling, D. L.

    1975-01-01

    Encoding of video signals using adaptive delta modulation (DM) was investigated, along with the error correction of DM encoded signals corrupted by thermal noise. Conversion from pulse code modulation to delta modulation was studied; an expression for the signal to noise ratio of the DM signal derived was achieved by employing linear, 2-sample, interpolation between sample points. A phase locked loop using a nonlinear processor in lieu of a loop filter is discussed.

  19. Design Considerations for Phased Array Modules

    Science.gov (United States)

    1980-11-01

    basica )ly designed for C7 operation. In pulsed mode of oporation however, peak pov:e%.’ of 150:7 at 10.52GHz wras obtained for psoc pulse lengths and...repeating the above calculations with the appropriate value of referer:ce phase ýP applied to each element. Bearing in mind the tedious algebra involved in

  20. Cylindrical PVF2 film based fiber optic phase modulator - Phase shift nonlinearity and frequency response

    Science.gov (United States)

    Sudarshanam, V. S.; Claus, Richard O.

    1993-03-01

    A new cylindrical coil configuration for polyvinylidene flouride (PVF2) film based fiber optic phase modulator is studied for the frequency response and nonlinearity of phase shift at the resonance frequency. This configuration, hitherto unapproached for PVF2 film modulators, offers resonance at well defined, controllable and higher frequencies than possible for the flat-strip configuration. Two versions of this configuration are presented that differ strongly in both the resonance frequency and the phase shift nonlinearity coefficient.

  1. Crystal structure of the commensurately modulated ζ phase of PAMC

    DEFF Research Database (Denmark)

    Harris, P.; Larsen, F.K.; Lebech, B.

    1994-01-01

    The commensurately modulated zeta low-temperature phase of bis(propylammonium) tetrachloromanganate(II), [NH3(C3H7)]2MnCl4, has been determined at 8 K. a = 7.437 (5), b = 7.082 (5), c = 13.096 (8) Angstrom, alpha = 105.59 (1)degrees. Superspace group P2(1)/b(0 beta 0)(1) over bar s, with beta = 1...... phase, indicating a 'lock-in' and phase shift between adjacent modulated layers. The modulation waves do not change much from the values of the epsilon phase, which confirms the lock-in of the modulation vector; only some components of the modulations of the propylammonium chains appear....../3, V = 664.4, Z = 2 D-x = 1.58 g cm(-3) Mo K alpha radiation, lambda = 0.71069 Angstrom, mu = 17.99 cm(-1) F(000) = 326, wR(F) = 0.064 for 1444 main reflections and wR(F) = 0.089 for 248 satellite reflections. The modulation vector flips and locks into a commensurate value compared with the epsilon...

  2. Polarization-multiplexed rate-adaptive non-binary-quasi-cyclic-LDPC-coded multilevel modulation with coherent detection for optical transport networks.

    Science.gov (United States)

    Arabaci, Murat; Djordjevic, Ivan B; Saunders, Ross; Marcoccia, Roberto M

    2010-02-01

    In order to achieve high-speed transmission over optical transport networks (OTNs) and maximize its throughput, we propose using a rate-adaptive polarization-multiplexed coded multilevel modulation with coherent detection based on component non-binary quasi-cyclic (QC) LDPC codes. Compared to prior-art bit-interleaved LDPC-coded modulation (BI-LDPC-CM) scheme, the proposed non-binary LDPC-coded modulation (NB-LDPC-CM) scheme not only reduces latency due to symbol- instead of bit-level processing but also provides either impressive reduction in computational complexity or striking improvements in coding gain depending on the constellation size. As the paper presents, compared to its prior-art binary counterpart, the proposed NB-LDPC-CM scheme addresses the needs of future OTNs, which are achieving the target BER performance and providing maximum possible throughput both over the entire lifetime of the OTN, better.

  3. Phase Regeneration of a BPSK Data Signal Using a Lithium Niobate Phase Modulator

    DEFF Research Database (Denmark)

    Mulvad, Hans Christian Hansen; Da Ros, Francesco; Galili, Michael

    2015-01-01

    We propose a scheme for phase regeneration of an optical binary phase shift keying (BPSK) data signal using a Lithium Niobate (LiNbO3) phase modulator. The scheme is based on heterodyne detection of the BPSK data signal with a continuous wave local oscillator (CW-LO). Carrier recovery...... is then achieved in the electrical domain using a ×2 frequency-multiplier and a narrow-band filtering scheme. Subsequently, a superposition of the recovered carrier and the heterodyne detected data signal is used to modulate the CW-LO in a LiNbO3 phase modulator. The result is a parametric mixing process...... in the optical domain, leading to a phase-regenerated BPSK data signal by the coherent superposition with a phase-inverted copy. The proposed scheme constitutes a compact and stable setup, where active phase-stabilization of the electrical data- and carrier-paths can potentially be avoided. An analytical...

  4. INFLUENCE OF POLARIZATION MODE DISPERSION ON THE EFFECT OF CROSS-PHASE MODULATION IN INTENSITY MODULATION-DIRECT DETECTION WDM TRANSMISSION SYSTEM

    Directory of Open Access Journals (Sweden)

    M S Islam

    2010-03-01

    Full Text Available Cross-phase modulation (XPM changes the state-of-polarization (SOP of the channels through nonlinear polarization rotation and induces nonlinear time dependent phase shift for polarization components that leads to amplitude modulation of the propagating waves in a wavelength division multiplexing (WDM system. Due to the presence of birefringence, the angle between the SOP changes randomly and as a result polarization mode dispersion (PMD causes XPM modulation amplitude fluctuation random in the perturbed channel. In this paper we analytically determine the probability density function of the random angle between the SOP of pump and probe, and evaluate the impact of polarization mode dispersion on XPM in terms of bit error rate, channel spacing etc for a two channel intensity modulation-direct detection WDM system at 10 Gb/s. It is found that the XPM induced crosstalk is polarization independent for channel spacing greater than 3 nm or PMD coefficient larger than 2 ps/√km. We also investigate the dependence of SOP variance on PMD coefficient and channel spacing.

  5. NEW SELF-MIXING MICROINTERFEROMETER BASED ON EXTERNAL PHASE MODULATION

    Institute of Scientific and Technical Information of China (English)

    GUO Dongmei; WANG Ming

    2007-01-01

    A new self-mixing micro-interferometer based on external phase modulation is presented.Self-mixing interference occurs in a laser diode (LD) by reflecting the light from a mirror-like target in front of the laser. Sinusoidal phase modulation of the beam is obtained by an electro-optic crystal (EOC) in the external cavity. The phase of the interference signal is demodulated by Fourier analysis method. The combination of the modulation and demodulation decreases the sensitivity of the instrument to fluctuations of the laser power and the noise induced by environment. Experimentally, the new micro-interferometer is applied to measure the micro-displacement of a high precision commercial PZT with an accuracy of<10 nm.

  6. Detector Modules for the CMS Pixel Phase 1 Upgrade

    CERN Document Server

    Zhu, De Hua; Berger, Pirmin; Meinhard, Maren Tabea; Starodumov, Andrey; Tavolaro, Vittorio Raoul

    2017-01-01

    The CMS Pixel phase 1 upgrade detector consists of 1184 modules with new design. An important part of the production is the module qualification and calibration, ensuring their proper functionality within the detector. This paper summarizes the qualification and calibration results of modules used in the innermost two detector layers with focus on methods using module-internal calibration signals. Extended characterizations on pixel level such as electronic noise and bump bond connectivity, optimization of operational parameters, sensor quality and thermal stress resistance were performed using a customized setup with controlled environment. It could be shown that the selected modules have on average $0.55 \\mathrm{ {}^{0\\!}\\!/\\!_{00} }\\, \\pm \\, 0.01 \\mathrm{ {}^{0\\!}\\!/\\!_{00} }\\,$ defective pixels and that all performance parameters stay within their specifications.

  7. Enabling Technologies for Direct Detection Optical Phase Modulation Formats

    Science.gov (United States)

    Xu, Xian

    Phase modulation formats are believed to be one of the key enabling techniques for next generation high speed long haul fiber-optic communication systems due to the following main advantages: (1) with a balanced detection, a better receiver sensitivity over conventional intensity modulation formats, e.g., a ˜3-dB sensitivity improvement using differential phase shift keying (DPSK) and a ˜1.3-dB sensitivity improvement using differential quadrature phase shift keying (DQPSK); (2) excellent robustness against fiber nonlinearities; (3) high spectrum efficiency when using multilevel phase modulation formats, such as DQPSK. As the information is encoded in the phase of the optical field, the phase modulation formats are sensitive to the phase-related impairments and the deterioration induced in the phase-intensity conversion. This consequently creates new challenging issues. The research objective of this thesis is to depict some of the challenging issues and provide possible solutions. The first challenge is the cross-phase modulation (XPM) penalty for the phase modulated channels co-propagating with the intensity modulated channels. The penalty comes from the pattern dependent intensity fluctuations of the neighboring intensity modulated channels being converted into phase noise in the phase modulation channels. We propose a model to theoretically analyze the XPM penalty dependence on the walk off effect. From this model, we suggest that using fibers with large local dispersion or intentionally introducing some residual dispersion per span would help mitigate the XPM penalty. The second challenge is the polarization dependent frequency shift (PDf) induced penalty during the phase-intensity conversion. The direct detection DPSK is usually demodulated in a Mach-Zehnder delay interferometer (DI). The polarization dependence of DI introduces a PDf causing a frequency offset between the laser's frequency and the transmissivity peak of DI, degrading the demodulated DPSK

  8. Phase modulation mode of scanning ion conductance microscopy

    Energy Technology Data Exchange (ETDEWEB)

    Li, Peng; Zhang, Changlin [State Key Laboratory of Robotics, Shenyang Institute of Automation, Chinese Academy of Sciences, Shenyang 110016 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Liu, Lianqing, E-mail: lqliu@sia.cn, E-mail: gli@engr.pitt.edu; Wang, Yuechao; Yang, Yang [State Key Laboratory of Robotics, Shenyang Institute of Automation, Chinese Academy of Sciences, Shenyang 110016 (China); Li, Guangyong, E-mail: lqliu@sia.cn, E-mail: gli@engr.pitt.edu [Department of Electrical and Computer Engineering, University of Pittsburgh, Pittsburgh, Pennsylvania 15261 (United States)

    2014-08-04

    This Letter reports a phase modulation (PM) mode of scanning ion conductance microscopy. In this mode, an AC current is directly generated by an AC voltage between the electrodes. The portion of the AC current in phase with the AC voltage, which is the current through the resistance path, is modulated by the tip-sample distance. It can be used as the input of feedback control to drive the scanner in Z direction. The PM mode, taking the advantages of both DC mode and traditional AC mode, is less prone to electronic noise and DC drift but maintains high scanning speed. The effectiveness of the PM mode has been proven by experiments.

  9. Mechanical modulation method for ultrasensitive phase measurements in photonics biosensing.

    Science.gov (United States)

    Patskovsky, S; Maisonneuve, M; Meunier, M; Kabashin, A V

    2008-12-22

    A novel polarimetry methodology for phase-sensitive measurements in single reflection geometry is proposed for applications in optical transduction-based biological sensing. The methodology uses altering step-like chopper-based mechanical phase modulation for orthogonal s- and p- polarizations of light reflected from the sensing interface and the extraction of phase information at different harmonics of the modulation. We show that even under a relatively simple experimental arrangement, the methodology provides the resolution of phase measurements as low as 0.007 deg. We also examine the proposed approach using Total Internal Reflection (TIR) and Surface Plasmon Resonance (SPR) geometries. For TIR geometry, the response appears to be strongly dependent on the prism material with the best values for high refractive index Si. The detection limit for Si-based TIR is estimated as 10(-5) in terms Refractive Index Units (RIU) change. SPR geometry offers much stronger phase response due to a much sharper phase characteristics. With the detection limit of 3.2*10(-7) RIU, the proposed methodology provides one of best sensitivities for phase-sensitive SPR devices. Advantages of the proposed method include high sensitivity, simplicity of experimental setup and noise immunity as a result of a high stability modulation.

  10. Phase-visibility modulating interferometry by binary non-quadrature amplitude modulation with neutral density filters

    Science.gov (United States)

    Rivera-Ortega, Uriel; Meneses-Fabian, Cruz; Rodriguez-Zurita, Gustavo; Robledo-Sanchez, Carlos

    2014-04-01

    An alternative method for phase retrieval based on spatial and binary non-quadrature amplitude modulation (NQAM) is presented. This proposal is based on the superposition of a probe beam with a reference beam modulated in phase and amplitude (PAM) by NQAM, which is implemented by two neutral density filters (NDF) in a three-beam Mach-Zehnder interferometer (MZI). The principal advantage of this proposal lies in an analytical relationship between the variations of phase and visibility in an interferogram with the variations in the amplitudes of the reference beams used to implement NQAM; thus, the interferograms can be normalized and their introduced phase variations can be known from the measured intensities. Consequently it is possible to successfully retrieve the object phase. It is worthy to note that this method is capable of accepting that the phase and visibility variations in the interferograms could be spatial functions.

  11. Code-modulated interferometric imaging system using phased arrays

    Science.gov (United States)

    Chauhan, Vikas; Greene, Kevin; Floyd, Brian

    2016-05-01

    Millimeter-wave (mm-wave) imaging provides compelling capabilities for security screening, navigation, and bio- medical applications. Traditional scanned or focal-plane mm-wave imagers are bulky and costly. In contrast, phased-array hardware developed for mass-market wireless communications and automotive radar promise to be extremely low cost. In this work, we present techniques which can allow low-cost phased-array receivers to be reconfigured or re-purposed as interferometric imagers, removing the need for custom hardware and thereby reducing cost. Since traditional phased arrays power combine incoming signals prior to digitization, orthogonal code-modulation is applied to each incoming signal using phase shifters within each front-end and two-bit codes. These code-modulated signals can then be combined and processed coherently through a shared hardware path. Once digitized, visibility functions can be recovered through squaring and code-demultiplexing operations. Pro- vided that codes are selected such that the product of two orthogonal codes is a third unique and orthogonal code, it is possible to demultiplex complex visibility functions directly. As such, the proposed system modulates incoming signals but demodulates desired correlations. In this work, we present the operation of the system, a validation of its operation using behavioral models of a traditional phased array, and a benchmarking of the code-modulated interferometer against traditional interferometer and focal-plane arrays.

  12. Multilevel Modulation formats for Optical Communication

    DEFF Research Database (Denmark)

    Jensen, Jesper Bevensee

    2008-01-01

    This thesis studies the use of multilevel modulation formats for optical communication systems. Multilevel modulation is an attractive method of increasing the spectral efficiency of optical communication systems. Various modulation formats employing phase modulation, amplitude modulation...... or a combination of the two have been studied. The use of polarization multiplexing (PolMux) to double the bit rate has also been investigated. The impact of transmission impairments such as chromatic dispersion, self phase modulation and cross phase modulation has been investigated. The feasibility of multilevel...... modulation for network oriented scenarios has been demonstrated....

  13. Radio over fiber link with adaptive order n‐QAM optical phase modulated OFDM and digital coherent detection

    DEFF Research Database (Denmark)

    Arlunno, Valeria; Borkowski, Robert; Guerrero Gonzalez, Neil

    2011-01-01

    Successful digital coherent demodulation of asynchronous optical phase‐modulated adaptive order QAM (4, 16, and 64) orthogonal frequency division multiplexing signals is achieved by a single reconfigurable digital receiver after 78 km of optical deployed fiber transmission....

  14. Phase shifting mask modulated laser patterning on graphene

    Science.gov (United States)

    Gao, Fan; Liu, Fengyuan; Ye, Ziran; Sui, Chenghua; Yan, Bo; Cai, Pinggen; Lv, Bin; Li, Yun; Chen, Naibo; Zheng, Youdou; Shi, Yi

    2017-01-01

    A one-step graphene patterning method is developed in this paper. A phase shifting mask is used to modulate incident laser beam spatially and generate graphene patterns by laser heating. Periodic graphene nanoribbon and nanomesh structures are fabricated by employing 1D and 2D phase shifting masks, respectively. The noncontact, simple procedure, easy handling and economic properties of this method make it promising towards graphene-based device fabrication.

  15. 10 GHz pulse source for 640 Gbit/s OTDM based on phase modulator and self-phase modulation

    DEFF Research Database (Denmark)

    Hu, Hao; Mulvad, Hans Christian Hansen; Peucheret, Christophe

    2011-01-01

    to compensate the chirp. The non-linear pulse compression stages are based on self-phase modulation (SPM) in dispersion-flattened highly non-linear fibers (DF-HNLF). The pulse source is tunable over the C-band with negligible pedestal. © 2011 Optical Society of America....... the high pulse quality. The pulse source is based on a linear pulse compression stage followed by two polarization-independent non-linear pulse compression stages. The linear pulse compression stage relies on a phase modulator, which is used to generate linear chirp and followed by a dispersive element...

  16. Frequency transfer via a two-way optical phase comparison on a multiplexed fiber network.

    Science.gov (United States)

    Calosso, C E; Bertacco, E; Calonico, D; Clivati, C; Costanzo, G A; Frittelli, M; Levi, F; Mura, A; Godone, A

    2014-03-01

    We performed a two-way remote optical phase comparison on optical fiber. Two optical frequency signals were launched in opposite directions in an optical fiber and their phases were simultaneously measured at the other end. In this technique, the fiber noise is passively canceled, and we compared two optical frequencies at the ultimate 10(-21) stability level. The experiment was performed on a 47 km fiber that is part of the metropolitan network for Internet traffic. The technique relies on the synchronous measurement of the optical phases at the two ends of the link, which is here performed by digital electronics. This scheme offers some advantages with respect to active noise cancellation schemes, as the light travels only once in the fiber.

  17. Particle modulations to turbulence in two-phase round jets

    Institute of Scientific and Technical Information of China (English)

    Bing Wang; Huiqiang Zhang; Yi Liu; Xiaofen Yan; Xilin Wang

    2009-01-01

    The particle modulations to turbulence in round jets were experimentally studied by means of two-phase velocity measurements with Phase Doppler Anemometer (PDA). Laden with very large particles, no significant attenuations of turbulence intensities were measured in the far-fields, due to small two-phase slip velocities and particle Reynolds number. The gas-phase turbulence is enhanced by particles in the near-fields, but it is significantly attenuated by the small particles in the far-fields. The smaller particles have a more profound effect on the attenuation of turbulence intensities. The enhancements or attenuations of turbulence intensities in the far-fields depends on the energy production, transport and dissipation mechanisms between the two phases, which are determined by the particle prop-erties and two-phase velocity slips. The non-dimensional parameter CTI is introduced to represent the change of turbulence intensity.

  18. Charge modulation as fingerprints of phase-string triggered interference

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Zheng; Tian, Chushun; Jiang, Hong-Chen; Qi, Yang; Weng, Zheng-Yu; Zaanen, Jan

    2015-07-07

    Charge order appears to be an ubiquitous phenomenon in doped Mott insulators, which is currently under intense experimental and theoretical investigations particularly in the high T c cuprates. This phenomenon is conventionally understood in terms of Hartree-Fock-type mean-field theory. Here we demonstrate a mechanism for charge modulation which is rooted in the many-particle quantum physics arising in the strong coupling limit. Specifically, we consider the problem of a single hole in a bipartite t - J ladder. As a remnant of the fermion signs, the hopping hole picks up subtle phases pending the fluctuating spins, the so-called phase-string effect. We demonstrate the presence of charge modulations in the density matrix renormalization group solutions which disappear when the phase strings are switched off. This form of charge modulation can be understood analytically in a path-integral language with a mean-field-like approximation adopted, showing that the phase strings give rise to constructive interferences leading to self-localization. When the latter occurs, left- and right-moving propagating modes emerge inside the localization volume and their interference is responsible for the real space charge modulation.

  19. Coherence control of pulse trains by spectral phase modulation

    Science.gov (United States)

    Ding, Chaoliang; Koivurova, Matias; Turunen, Jari; Setälä, Tero; Friberg, Ari T.

    2017-09-01

    We propose a technique to control the spectral and temporal coherence properties of pulsed beams of light via time-dependent manipulation of the spectral phase. Modulation schemes for the generation of partially coherent pulse trains from a train of fully coherent pulses are presented. The feasibility of experimental realization of the method is confirmed by numerical estimates.

  20. Phase-controlled superconducting heat-flux quantum modulator

    Science.gov (United States)

    Giazotto, F.; Martínez-Pérez, M. J.

    2012-09-01

    We theoretically put forward the concept of a phase-controlled superconducting heat-flux quantum modulator. Its operation relies on phase-dependent heat current predicted to occur in temperature-biased Josephson tunnel junctions. The device behavior is investigated as a function of temperature bias across the junctions, bath temperature, and junctions asymmetry as well. In a realistic Al-based setup the structure could provide temperature modulation amplitudes up to ˜50 mK with flux-to-temperature transfer coefficients exceeding ˜125 mK/Φ0 below 1 K, and temperature modulation frequency of the order of a few MHz. The proposed structure appears as a promising building-block for the implementation of caloritronic devices operating at cryogenic temperatures.

  1. On-chip multiplexed solid-phase nucleic acid hybridization assay using spatial profiles of immobilized quantum dots and fluorescence resonance energy transfer

    Energy Technology Data Exchange (ETDEWEB)

    Noor, M. Omair; Tavares, Anthony J.; Krull, Ulrich J., E-mail: ulrich.krull@utoronto.ca

    2013-07-25

    Graphical abstract: -- Highlights: •Solid-phase multiplexed QD-FRET nucleic acid assay in electrokinetic fluidic chip. •Concurrent detection of two oligonucleotides based on channel length coverage. •Selection of “turn-on” and “turn-off” signals from two acceptor dyes and two colors of immobilized QDs, respectively. •No loss in assay sensitivity when implementing multiplexed assay format. -- Abstract: A microfluidic based solid-phase assay for the multiplexed detection of nucleic acid hybridization using quantum dot (QD) mediated fluorescence resonance energy transfer (FRET) is described herein. The glass surface of hybrid glass-polydimethylsiloxane (PDMS) microfluidic channels was chemically modified to assemble the biorecognition interface. Multiplexing was demonstrated using a detection system that was comprised of two colors of immobilized semi-conductor QDs and two different oligonucleotide probe sequences. Green-emitting and red-emitting QDs were paired with Cy3 and Alexa Fluor 647 (A647) labeled oligonucleotides, respectively. The QDs served as energy donors for the transduction of dye labeled oligonucleotide targets. The in-channel assembly of the biorecognition interface and the subsequent introduction of oligonucleotide targets was accomplished within minutes using a combination of electroosmotic flow and electrophoretic force. The concurrent quantification of femtomole quantities of two target sequences was possible by measuring the spatial coverage of FRET sensitized emission along the length of the channel. In previous reports, multiplexed QD-FRET hybridization assays that employed a ratiometric method for quantification had challenges associated with lower analytical sensitivity arising from both donor and acceptor dilution that resulted in reduced energy transfer pathways as compared to single-color hybridization assays. Herein, a spatial method for quantification that is based on in-channel QD-FRET profiles provided higher analytical

  2. Multiplexed aberration measurement for deep tissue imaging in vivo

    OpenAIRE

    Wang, Chen; Liu, Rui; Milkie, Daniel E; Sun, Wenzhi; Tan, Zhongchao; Kerlin, Aaron; Chen, Tsai-Wen; Kim, Douglas S.; Ji, Na

    2014-01-01

    We describe a multiplexed aberration measurement method that modulates the intensity or phase of light rays at multiple pupil segments in parallel to determine their phase gradients. Applicable to fluorescent-protein-labeled structures of arbitrary complexity, it allows us to obtain diffraction-limited resolution in various samples in vivo. For the strongly scattering mouse brain, a single aberration correction improves structural and functional imaging of fine neuronal processes over a large...

  3. Multiplexed aberration measurement for deep tissue imaging in vivo

    Science.gov (United States)

    Wang, Chen; Liu, Rui; Milkie, Daniel E.; Sun, Wenzhi; Tan, Zhongchao; Kerlin, Aaron; Chen, Tsai-Wen; Kim, Douglas S.; Ji, Na

    2014-01-01

    We describe a multiplexed aberration measurement method that modulates the intensity or phase of light rays at multiple pupil segments in parallel to determine their phase gradients. Applicable to fluorescent-protein-labeled structures of arbitrary complexity, it allows us to obtain diffraction-limited resolution in various samples in vivo. For the strongly scattering mouse brain, a single aberration correction improves structural and functional imaging of fine neuronal processes over a large imaging volume. PMID:25128976

  4. Optical phase encryption by phase contrast using electrically addressed spatial light modulator

    Science.gov (United States)

    Nishchal, Naveen Kumar; Joseph, Joby; Singh, Kehar

    2003-03-01

    We report the use of an electrically addressed liquid crystal spatial light modulator (EALCSLM) operating in the phase mode as a phase-contrast filter (PCF). As an application, an optical phase encryption system has been implemented. We encrypt and decrypt a two-dimensional phase image obtained from an amplitude image. Encrypted image is holographically recorded in a Barium titanate crystal and is then decrypted by generating through phase conjugation, a conjugate of the encrypted image. The decrypted phase image is converted into an amplitude image using an EASLM as a PCF. The idea has been supported by the experimental results.

  5. A Method and an Apparatus for Generating a Phase-Modulated Wave Front of Electromagnetic Radiation

    DEFF Research Database (Denmark)

    2002-01-01

    The present invention provides a method and a system for generating a phase-modulated wave front. According to the present invention, the spatial phase-modulation is not performed on the different parts of the wave front individually as in known POSLMs. Rather, the spatial phase-modulation of the......The present invention provides a method and a system for generating a phase-modulated wave front. According to the present invention, the spatial phase-modulation is not performed on the different parts of the wave front individually as in known POSLMs. Rather, the spatial phase......-modulation of the present invention is performed by generating an amplitude modulation in the wave front, Fourier or Fresnel transforming the amplitude modulated wave front, filtering Fourier or Fresnel components of the Fourier or Fresnel distribution with a spatial filter such as a phase contrast filter, and regenerating...... the wave front whereby the initial amplitude modulation has transformed into a phase-modulation....

  6. Phase microscopy of technical and biological samples through random phase modulation with a difuser

    DEFF Research Database (Denmark)

    Almoro, Percival; Pedrini, Giancarlo; Gundu, Phanindra Narayan

    2010-01-01

    A technique for phase microscopy using a phase diffuser and a reconstruction algorithm is proposed. A magnified specimen wavefront is projected on the diffuser plane that modulates the wavefront into a speckle field. The speckle patterns at axially displaced planes are sampled and used in an iter...

  7. Phase matching of high order harmonic generation using dynamic phase modulation caused by a non-collinear modulation pulse

    Science.gov (United States)

    Cohen, Oren; Kapteyn, Henry C.; Mumane, Margaret M.

    2010-02-16

    Phase matching high harmonic generation (HHG) uses a single, long duration non-collinear modulating pulse intersecting the driving pulse. A femtosecond driving pulse is focused into an HHG medium (such as a noble gas) to cause high-harmonic generation (HHG), for example in the X-ray region of the spectrum, via electrons separating from and recombining with gas atoms. A non-collinear pulse intersects the driving pulse within the gas, and modulates the field seen by the electrons while separated from their atoms. The modulating pulse is low power and long duration, and its frequency and amplitude is chosen to improve HHG phase matching by increasing the areas of constructive interference between the driving pulse and the HHG, relative to the areas of destructive interference.

  8. LIGHT MODULATION: Quasi-collinear tunable acousto-optic paratellurite crystal filters for wavelength division multiplexing and optical channel selection

    Science.gov (United States)

    Molchanov, V. Ya; Voloshinov, V. B.; Makarov, O. Yu

    2009-04-01

    Quasi-collinear acousto-optic interaction is studied in acoustically and optically anisotropic paratellurite crystals. The possible applications of this interaction in acousto-optic tunable filters with a high spectral resolution are discussed. Different modifications of devices are compared and variants of devices intended for processing light beams and selection of light signals in fibreoptic communication systems with wavelength division multiplexing (WDM) at λ simeq 1550 nm are considered.

  9. Implementation of Phase Generated Carrier Technique for FBG Laser Sensor Multiplexed System Based on Compact RIO

    Institute of Scientific and Technical Information of China (English)

    Lei Feng; Jun He; Jing-Yuan Duan; Fang Li; Yu-Liang Liu

    2008-01-01

    This paper presents the fundamental technique of phase generated carrier (PGC) and its realization on compact reconfigurable input and output (RIO) which adopts real-time and field programmable grate array (FPGA) techniques. Improvement of the PGC technique is also introduced by using peak-to-peak value detection method to reduce the influence of variation of the light intensity. A four-element fibre Bragg gratings (FBG) laser sensor system is conducted in the experiment and the demodulated results demonstrate correlation coefficient as high as 0.995 with the reference signal and the dynamic range to be 120dB@63Hz.

  10. Temporally modulated phase retrieval method for weak temporal phase measurement of laser pulses

    CERN Document Server

    Qiao, Zhi; Wang, Xiaochao; Jing, Yuanyuan; Fan, Wei; Lin, Zunqi

    2016-01-01

    The measurement of weak temporal phase for picosecond and nanosecond laser pulses is important but quite difficult. We propose a simple iterative algorithm, which is based on a temporally movable phase modulation process, to retrieve the weak temporal phase of laser pulses. This unambiguous method can achieve a high accuracy and simultaneously measure the weak temporal phase and temporal profile of pulses, which are almost transform-limited. Detailed analysis shows that this iterative method has valuable potential applications in the characterization of pulses with weak temporal phase.

  11. Large conditional single-photon cross-phase modulation

    CERN Document Server

    Beck, Kristin M; Duan, Yiheng; Vuletić, Vladan

    2015-01-01

    Deterministic optical quantum logic requires a nonlinear quantum process that alters the phase of a quantum optical state by $\\pi$ through interaction with only one photon. Here, we demonstrate a large conditional cross-phase modulation between a signal field, stored inside an atomic quantum memory, and a control photon that traverses a high-finesse optical cavity containing the atomic memory. This approach avoids fundamental limitations associated with multimode effects for traveling optical photons. We measure a conditional cross-phase shift of up to $\\pi/3$ between the retrieved signal and control photons, and confirm deterministic entanglement between the signal and control modes by extracting a positive concurrence. With a moderate improvement in cavity finesse, our system can reach a coherent phase shift of $\\pi$ at low loss, enabling deterministic and universal photonic quantum logic.

  12. Towards a FPGA-controlled deep phase modulation interferometer

    CERN Document Server

    Terán, M; Gesa, L l; Mateos, I; Gibert, F; Karnesis, N; Ramos-Castro, J; Schwarze, T S; Gerberding, O; Heinzel, G; Guzmán, F; Nofrarias, M

    2014-01-01

    Deep phase modulation interferometry was proposed as a method to enhance homodyne interferometers to work over many fringes. In this scheme, a sinusoidal phase modulation is applied in one arm while the demodulation takes place as a post-processing step. In this contribution we report on the development to implement this scheme in a fiber coupled interferometer controlled by means of a FPGA, which includes a LEON3 soft-core processor. The latter acts as a CPU and executes a custom made application to communicate with a host PC. In contrast to usual FPGA-based designs, this implementation allows a real-time fine tuning of the parameters involved in the setup, from the control to the post-processing parameters.

  13. Dynamic phase-control of a rising sun magnetron using modulated and continuous current

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez-Gutierrez, Sulmer, E-mail: sulmer.a.fernandez.gutierrez@intel.com [Intel Corporation, 2111 NE 25th Ave, Hillsboro, Oregon 97214 (United States); Browning, Jim [Department of Electrical and Computer Engineering, Boise State University, Boise, Idaho 83725 (United States); Lin, Ming-Chieh [Department of Electrical and Biomedical Engineering, Hanyang University, Seoul 133-791 (Korea, Republic of); Smithe, David N. [Tech-X Corporation, 5621 Arapahoe Ave, Boulder, Colorado 80303 (United States); Watrous, Jack [Confluent Sciences, LLC, Albuquerque, New Mexico 87111 (United States)

    2016-01-28

    Phase-control of a magnetron is studied via simulation using a combination of a continuous current source and a modulated current source. The addressable, modulated current source is turned ON and OFF at the magnetron operating frequency in order to control the electron injection and the spoke phase. Prior simulation work using a 2D model of a Rising Sun magnetron showed that the use of 100% modulated current controlled the magnetron phase and allowed for dynamic phase control. In this work, the minimum fraction of modulated current source needed to achieve a phase control is studied. The current fractions (modulated versus continuous) were varied from 10% modulated current to 100% modulated current to study the effects on phase control. Dynamic phase-control, stability, and start up time of the device were studied for all these cases showing that with 10% modulated current and 90% continuous current, a phase shift of 180° can be achieved demonstrating dynamic phase control.

  14. Phase-dependent modulation of corticospinal excitability during the observation of the initial phase of gait.

    Science.gov (United States)

    Takahashi, Makoto; Uchida, Natsuko; Yoshida, Mami; Liang, Nan; Nakazawa, Kimitaka; Sekikawa, Kiyokazu; Inamizu, Tsutomu; Hamada, Hironobu

    2014-12-01

    This study was undertaken to identify the temporal characteristics of corticospinal excitability of tibialis anterior muscle during the observation of the initial phase of gait. For this purpose, using transcranial magnetic stimulation, we recorded motor evoked potentials (MEPs) during the observation of the second step of an actor's first three steps of gait initiation with (complex gait) or without (normal gait) an obstacle and unstable surface. The results demonstrate that (1) MEPs during the observation of the initial phase of normal gait were significantly increased only at early swing phase, but not other phases (mid-swing, heel contact, mid-stance, and heel off) and (2) MEPs during the observation of the initial phase of complex gait were significantly increased at early swing and also at mid-swing and heel contact phases. These findings provide the first evidence that corticospinal excitability during the observation of gait, especially the initial phase, is modulated in phase- and motor-demanded-dependent manners.

  15. Residual intensity modulation in resonator fiber optic gyros with sinusoidal wave phase modulation

    Institute of Scientific and Technical Information of China (English)

    Di-qing YING; Qiang LI; Hui-lian MA; Zhong-he JIN

    2014-01-01

    We present how residual intensity modulation (RIM) affects the performance of a resonator fiber optic gyro (R-FOG) through a sinusoidal wave phase modulation technique. The expression for the R-FOG system’s demodulation curve under RIM is obtained. Through numerical simulation with different RIM coefficients and modulation frequencies, we find that a zero deviation is induced by the RIM effect on the demodulation curve, and this zero deviation varies with the RIM coefficient and modulation frequency. The expression for the system error due to this zero deviation is derived. Simulation results show that the RIM-induced error varies with the RIM coefficient and modulation frequency. There also exists optimum values for the RIM coefficient and modulation frequency to totally eliminate the RIM-induced error, and the error increases as the RIM coefficient or modulation frequency deviates from its optimum value;however, in practical situations, these two parameters would not be exactly fixed but fluctuate from their respective optimum values, and a large system error is induced even if there exists a very small deviation of these two critical parameters from their optimum values. Simulation results indicate that the RIM-induced error should be con-sidered when designing and evaluating an R-FOG system.

  16. Comprehensive research on self phase modulation based optical delay systems

    Institute of Scientific and Technical Information of China (English)

    Yang Ai-Ying; Sun Yu-Nan

    2010-01-01

    This paper comprehensively investigates the properties of self phase modulation based optical delay systems consisting of dispersion compensation fibre and highly nonlinear fibres.It researches into the impacts of power level launched into highly nonlinear fibres,conversion wavelength,dispersion slope,modulation format and optical filter bandwidth on the overall performance of optical delay systems.The results reveal that,if the power launched into highly nonlinear fibres is fixed,the time delay generally varies linearly with the conversion wavelength,but jumps intermittently at some conversion wavelengths.However,the time delay varies semi-periodically with the power launched into highly nonlinear fibres.The dispersion slope of highly nonlinear fibres has significant influence on the time delay,especially for the negative dispersion slope.The time delay differs with modulation formats due to the different combined interaction of nonlinearity and dispersion in fibres.The bandwidth of the optical filters also greatly affects the time delay because it determines the bandwidth of the passed signal in the self phase modulation based time delay systems.The output signal quality of the overall time delay systems depends on the conversion wavelength and input power level.The optimisation of the power level and conversion wavelength to provide the best output signal quality is made at the end of this paper.

  17. Phase modulated solitary waves controlled by bottom boundary condition

    CERN Document Server

    Mukherjee, Abhik

    2014-01-01

    A forced KdV equation is derived to describe weakly nonlinear, shallow water surface wave propagation over non trivial bottom boundary condition. We show that different functional forms of bottom boundary conditions self-consistently produce different forced kdV equations as the evolution equations for the free surface. Solitary wave solutions have been analytically obtained where phase gets modulated controlled by bottom boundary condition whereas amplitude remains constant.

  18. Conversion of phase-modulated signals to amplitude-modulated signals in SOAs due to mirror reflections

    DEFF Research Database (Denmark)

    Blaaberg, Søren; Mørk, Jesper

    2009-01-01

    We present theoretical results that show conversion of phase modulated signals to amplitude modulated signals in an SOA. Large-signal and small-signal calculations show significant conversion responses caused by even minute reflections at the end mirrors.......We present theoretical results that show conversion of phase modulated signals to amplitude modulated signals in an SOA. Large-signal and small-signal calculations show significant conversion responses caused by even minute reflections at the end mirrors....

  19. Design of CMOS compatible and compact, thermally-compensated electro-optic modulator based on off-axis microring resonator for dense wavelength division multiplexing applications.

    Science.gov (United States)

    Haldar, Raktim; Banik, Abhik D; Varshney, Shailendra K

    2014-09-22

    In this work, we propose and demonstrate the performance of silicon-on-insulator (SOI) off-axis microring resonator (MRR) as electro-optic modulator (EOM). Adding an extra off-axis inner-ring in conventional microring structure provides control to compensate thermal effects on EOM. It is shown that dynamically controlled bias-voltage applied to the outer ring has the potency to quell the thermal effects over a wide range of temperature. Thus, besides the appositely biased conventional microring, off-axis inner microring with pre-emphasized electrical input message signal enables our proposed structure suitable for high data-rate dense wavelength division multiplexing scheme of optical communication within a very compact device size.

  20. Phase microscopy of technical and biological samples through random phase modulation with a difuser

    DEFF Research Database (Denmark)

    Almoro, Percival; Pedrini, Giancarlo; Gundu, Phanindra Narayan

    2010-01-01

    A technique for phase microscopy using a phase diffuser and a reconstruction algorithm is proposed. A magnified specimen wavefront is projected on the diffuser plane that modulates the wavefront into a speckle field. The speckle patterns at axially displaced planes are sampled and used...... in an iterative phase retrieval algorithm based on a wave-propagation equation. The technique offers a whole-field and high-resolution wavefront reconstruction of unstained microstructures. Phase maps of photoresist targets and human cheek cells are obtained to demonstrate the effectiveness of our method. (C......) 2010 Optical Society of America...

  1. Natural transformation and phase variation modulation in Neisseria meningitidis.

    Science.gov (United States)

    Alexander, Heather L; Richardson, Anthony R; Stojiljkovic, Igor

    2004-05-01

    Neisseria meningitidis has evolved the ability to control the expression-state of numerous genes by phase variation. It has been proposed that the process aids this human pathogen in coping with the diversity of microenvironments and host immune systems. Therefore, increased frequencies of phase variation may augment the organism's adaptability and virulence. In this study, we found that DNA derived from various neisserial co-colonizers of the human nasopharynx increased N. meningitidis switching frequencies, indicating that heterologous neisserial DNA modulates phase variation in a transformation-dependent manner. In order to determine whether the effect of heterologous DNA was specific to the Hb receptor, HmbR, we constructed a Universal Rates of Switching cassette (UROS). With this cassette, we demonstrated that heterologous DNA positively affects phase variation throughout the meningococcal genome, as UROS phase variation frequencies were also increased in the presence of neisserial DNA. Overexpressing components of the neisserial mismatch repair system partially alleviated DNA-induced changes in phase variation frequencies, thus implicating mismatch repair titration as a cause of these transformation-dependent increases in switching. The DNA-dependent effect on phase variation was transient and may serve as a mechanism for meningococcal genetic variability that avoids the fitness costs encountered by global mutators.

  2. Numerical simulations on the focus-shift multiplexing technique for self-referential holographic data storage

    Science.gov (United States)

    Takabayashi, Masanori; Eto, Taisuke; Okamoto, Takashi

    2016-12-01

    For increasing the data density of holographic data storage (HDS), combining more than two multiplexing techniques is effective. This is also true in self-referential holographic data storage (SR-HDS) that enables holographic recording purely with a single beam. In this paper, a focus-shift multiplexing technique is applied to xy-shift multiplexed SR-HDS, the feasibility of which has been shown in our previous work. The focus-shift multiplexing technique enables the multiplexing of datapages by slightly changing the focal length of the objective lens. However, the required focus-shift distance for multiplexing and the implementation method of the focus-shift have not been clarified. First, the focus-shift selectivity is investigated by the numerical simulations. In the case where the focus-shift multiplexing technique is applied to xy-shift multiplexed SR-HDS, the inter-page crosstalk properties are clarified to decide the recording layout that can achieve a low-crosstalk readout. Second, the technique of displaying an additional phase pattern onto the spatial light modulator (SLM) is introduced, which is a focus-shift method without any special optical components, such as varifocal lenses. Finally, we investigate the relationship between the accuracy of the focus-shift and the parameters of SLM.

  3. Numerical simulations on the focus-shift multiplexing technique for self-referential holographic data storage

    Science.gov (United States)

    Takabayashi, Masanori; Eto, Taisuke; Okamoto, Takashi

    2016-08-01

    For increasing the data density of holographic data storage (HDS), combining more than two multiplexing techniques is effective. This is also true in self-referential holographic data storage (SR-HDS) that enables holographic recording purely with a single beam. In this paper, a focus-shift multiplexing technique is applied to xy -shift multiplexed SR-HDS, the feasibility of which has been shown in our previous work. The focus-shift multiplexing technique enables the multiplexing of datapages by slightly changing the focal length of the objective lens. However, the required focus-shift distance for multiplexing and the implementation method of the focus-shift have not been clarified. First, the focus-shift selectivity is investigated by the numerical simulations. In the case where the focus-shift multiplexing technique is applied to xy -shift multiplexed SR-HDS, the inter-page crosstalk properties are clarified to decide the recording layout that can achieve a low-crosstalk readout. Second, the technique of displaying an additional phase pattern onto the spatial light modulator (SLM) is introduced, which is a focus-shift method without any special optical components, such as varifocal lenses. Finally, we investigate the relationship between the accuracy of the focus-shift and the parameters of SLM.

  4. Linear, Low Noise Microwave Photonic Systems using Phase and Frequency Modulation

    Science.gov (United States)

    2012-05-11

    a monolithically integrated widely-tunable laser- phase modulator ,” in Proc. Optical Fiber Communication Conf. OFC 2004, vol. 2, 2004. [92] M. N... modulation efficiency experimental setup. . . . . . . . . . . . . . 70 5.5 DBR FM modulation efficiency versus frequency. . . . . . . . . . . . 71 v 5.6...Phase-noise limited noise figure for FM DBR lasers from measured modulation efficiency and linewidth. . . . . . . . . . . . . . . . . . . . 71 5.7

  5. Research on Feature Extraction of Composite Pseudocode Phase Modulation-Carrier Frequency Modulation Signal Based on PWD Transform

    Institute of Scientific and Technical Information of China (English)

    LI Ming-zi; ZHAO Hui-chang

    2008-01-01

    The identification features of composite pseudocode phase modulation and carry frequency modulation signal in-clude pseudocode and modulation frequency. In this paper, PWD is used to extract these features. First, the feature of pseudocode is extracted using the amplitude output of PWD and the correlation filter technology. Then the feature of fre-quency modulation is extracted by way of PWD analysis on the signal processed by anti-phase operation according to the extracted feature of pseudo code, i.e. position information of changed abruptly point of phase. The simulation result shows that both the features of frequency modulation and phase change position caused by the pseudocode phase modula-tion can be extracted effectively for SNR = 3 dB.

  6. Measurement of characteristics and phase modulation accuracy increase of LC SLM "HoloEye PLUTO VIS"

    Science.gov (United States)

    Bondareva, A. P.; Cheremkhin, P. A.; Evtikhiev, N. N.; Krasnov, V. V.; Starikov, R. S.; Starikov, S. N.

    2014-09-01

    Phase liquid crystal spatial light modulators (LC SLM) are actively integrated in various optical systems for dynamic diffractive optical elements imaging. To achieve the best performance, high stability and linearity of phase modulation is required. This article presents results of measurement of characteristics and phase modulation accuracy increase of state of the art LC SLM with HD resolution "HoloEye PLUTO VIS".

  7. Phase 1 pixel modules production and High Density Interconnect testing

    CERN Document Server

    Still, Joseph

    2014-01-01

    During the first run of the LHC, luminosity peaked at $1 \\times 10^{34} cm^{-2}s^{-1}$ with $ \\approx 50 ns$ bunch spacing a pile-up of about 25, or simultaneous inelastic collisions per crossing, occur in the CMS experiment. However after the upgrade of of the LHC during long shut down 1, luminosity, and therefore pile-up. Therefore the CMS pixel tracker has to be upgraded to be able to operate correctly under this news stronger constraints. That is how this CERN Summer Student project, which took place at the CERN Meyrin site, comes within the framework of the pixel detector upgrade in the CMS experiment with a work aimed on the phase 1 of pixel modules production and tests of the HDI. The production and tests of the HDI were held in cleanroom facilities. This included first hand as well as to work on pixel modules building and performing size and flatness tests on them, and on a other hand testing several HDIs. At first, prototypes modules were assembled before real modules building. Another aspect of work...

  8. MICS Asia Phase II - Sensitivity to the aerosol module

    CERN Document Server

    Sartelet, Karine; Sportisse, Bruno

    2007-01-01

    In the framework of the model inter-comparison study - Asia Phase II (MICS2), where eight models are compared over East Asia, this paper studies the influence of different parameterizations used in the aerosol module on the aerosol concentrations of sulfate and nitrate in PM10. An intracomparison of aerosol concentrations is done for March 2001 using different configurations of the aerosol module of one of the model used for the intercomparison. Single modifications of a reference setup for model configurations are performed and compared to a reference case. These modifications concern the size distribution, i.e. the number of sections, and physical processes, i.e. coagulation, condensation/evaporation, cloud chemistry, heterogeneous reactions and sea-salt emissions. Comparing monthly averaged concentrations at different stations, the importance of each parameterization is first assessed. It is found that sulfate concentrations are little sensitive to sea-salt emissions and to whether condensation is computed...

  9. Parallel phase modulation scheme for interferometric gravitational-wave detectors.

    Science.gov (United States)

    Hartman, M T; Quetschke, V; Tanner, D B; Reitze, D H; Mueller, G

    2014-11-17

    Advanced LIGO (aLIGO) requires multiple frequency sidebands to disentangle all of the main interferometer's length signals. This paper presents the results of a risk reduction experiment to produce two sets of frequency sidebands in parallel, avoiding mixed 'sidebands on sidebands'. Two phase modulation frequencies are applied to separate Electro-Optic Modulators (EOMs), with one EOM in each of the two arms of a Mach-Zehnder interferometer. In this system the Mach-Zehnder's arm lengths are stabilized to reduce relative intensity noise in the recombined carrier beam by feeding a corrective control signal back to the Rubidium Titanyl Phosphate (RTP) EOM crystals to drive the optical path length difference to zero. This setup's use of the RTP crystals as length actuators provides enough bandwidth in the feedback to meet arm length stability requirements for aLIGO.

  10. Scale-free brain ensemble modulated by phase synchronization

    Institute of Scientific and Technical Information of China (English)

    Dan WU; Chao-yi LI; Jie LIU; Jing LU; De-zhong YAO

    2014-01-01

    To listen to brain activity as a piece of music, we proposed the scale-free brainwave music (SFBM) technology, which could translate the scalp electroencephalogram (EEG) into music notes according to the power law of both EEG and music. In the current study, this methodology was further extended to a musical ensemble of two channels. First, EEG data from two selected channels are translated into musical instrument digital interface (MIDI) sequences, where the EEG parameters modulate the pitch, duration, and volume of each musical note. The phase synchronization index of the two channels is computed by a Hilbert transform. Then the two MIDI sequences are integrated into a chorus according to the phase synchronization index. The EEG with a high synchronization index is represented by more consonant musical intervals, while the low index is expressed by inconsonant musical intervals. The brain ensemble derived from real EEG segments illustrates differences in harmony and pitch distribution during the eyes-closed and eyes-open states. Furthermore, the scale-free phenomena exist in the brainwave ensemble. Therefore, the scale-free brain ensemble modulated by phase synchronization is a new attempt to express the EEG through an auditory and musical way, and it can be used for EEG monitoring and bio-feedback.

  11. A novel lab-on-chip platform with integrated solid phase PCR and Supercritical Angle Fluorescence (SAF) microlens array for highly sensitive and multiplexed pathogen detection

    DEFF Research Database (Denmark)

    Hung, Tran Quang; Chin, Wai Hoe; Sun, Yi

    2016-01-01

    Solid-phase PCR (SP-PCR) has become increasingly popular for molecular diagnosis and there have been a few attempts to incorporate SP-PCR into lab-on-a-chip (LOC) devices. However, their applicability for on-line diagnosis is hindered by the lack of sensitive and portable on-chip optical detectio......-PCR and SAF microlens array allows for on-chip highly sensitive and multiplexed pathogen detection with low-cost and compact optical components. The LOC platform would be widely used as a high-throughput biosensor to analyze food, clinical and environmental samples....

  12. Novel modulated Hexatic Phases in Symmetric Liquid Crystal Dimers

    OpenAIRE

    Date, R; Luckhurst, G.; Shuman, M.; Seddon, J

    1995-01-01

    Homologues of the dimeric α,ω-bis(4-n-alkylanilinebenzylidene-4'-oxy)alkanes (m.OnO.m) have been synthesised with spacer lengths n ranging from 9 to 12 methylene units and with terminal alkyl chain lengths m of 10, 12 and 14. Characterisation of these materials has been carried out by X-ray diffraction, differential scanning calorimetry and optical microscopy. In six of these compounds a novel modulated tilted hexatic phase, denoted S1, has been identified, in which the smectic layers have a ...

  13. Modulated phases of graphene quantum Hall polariton fluids

    Science.gov (United States)

    Pellegrino, Francesco M. D.; Giovannetti, Vittorio; MacDonald, Allan H.; Polini, Marco

    2016-11-01

    There is a growing experimental interest in coupling cavity photons to the cyclotron resonance excitations of electron liquids in high-mobility semiconductor quantum wells or graphene sheets. These media offer unique platforms to carry out fundamental studies of exciton-polariton condensation and cavity quantum electrodynamics in a regime, in which electron-electron interactions are expected to play a pivotal role. Here, focusing on graphene, we present a theoretical study of the impact of electron-electron interactions on a quantum Hall polariton fluid, that is a fluid of magneto-excitons resonantly coupled to cavity photons. We show that electron-electron interactions are responsible for an instability of graphene integer quantum Hall polariton fluids towards a modulated phase. We demonstrate that this phase can be detected by measuring the collective excitation spectra, which is often at a characteristic wave vector of the order of the inverse magnetic length.

  14. New space vector modulation technique for single-phase multilevel converters

    OpenAIRE

    León Galván, José Ignacio; Portillo Guisado, Ramón Carlos; García Franquelo, Leopoldo; Vázquez Pérez, Sergio; Carrasco Solís, Juan Manuel; Domínguez, E

    2007-01-01

    Single-phase multilevel converters are suitable for medium power applications as photovoltaic systems and switched reluctance machines. An overview of possible modulation methods including carrier-based pulse width modulation and space vector modulation techniques for multilevel single-phase converters is presented. A new space vector modulation for this type of converters is proposed. This space vector modulation method is very simple presenting low computational cost. Different solutions fo...

  15. Finding non-eclipsing binaries through pulsational phase modulation

    Science.gov (United States)

    Murphy, Simon J.; Bedding, Timothy R.; Shibahashi, Hiromoto; Kurtz, Donald W.; Kjeldsen, Hans

    2015-09-01

    We present a method for finding binaries among pulsating stars that were observed by the Kepler Mission. We use entire four-year light curves to accurately measure the frequencies of the strongest pulsation modes, then track the pulsation phases at those frequencies in 10-d segments. This produces a series of time-delay measurements in which binarity is apparent as a periodic modulation whose amplitude gives the projected light travel time across the orbit. Fourier analysis of this time-delay curve provides the parameters of the orbit, including the period, eccentricity, angle of ascending node and time of periastron passage. Differentiating the time-delay curve yields the full radial-velocity curve directly from the Kepler photometry, without the need for spectroscopy. We show examples with delta Scuti stars having large numbers of pulsation modes, including one system in which both components of the binary are pulsating. The method is straightforward to automate, thus radial velocity curves can be derived for hundreds of non-eclipsing binary stars from Kepler photometry alone. This contribution is based largely upon the work by Murphy et al. [1], describing the phase-modulation method in detail.

  16. Impacts of cross-phase modulation on modulation instability of Airy pulses

    Science.gov (United States)

    Cheng, Yingkai; Fu, Xiquan; Bai, Yanfeng

    2016-10-01

    The modulation instability (MI) of Airy pulses with the influence of cross-phase modulation is studied based on the coupled nonlinear Schrödinger equations in nonlinear media. The main lobe of Airy pulses can be manifested as breakup of MI under interaction with higher power pumped solitons, although the power of Airy pulses is small. By comparing the main lobe's gain spectrum of MI, the gain spectrum has gradually improved with the increase of power of pumped solitons. The gain spectrum of MI of the main lobe is inversely proportional to the truncation coefficient, and then it gradually approaches to that of Gauss pulses with the truncation coefficient increasing to 1. For the side lobes of Airy pulses, there are similar MI but smaller gain spectrum than the main lobe when the pumped solitons is overlapping with corresponding ones of Airy pulses.

  17. Tunable RF photonic phase shifter based on optical DSB modulation and FBG filtering

    Science.gov (United States)

    Wei, Yongfeng; Huang, Shanguo; Sun, Kai; Gao, Xinlu; Gu, Wanyi

    2016-01-01

    A broadband RF photonic phase shifter that can achieve the tunable phase shift with little RF amplitude variation is presented. It is based on homodyne mixing technique. The beating between phase-modulated optical carrier and the sidebands can generate RF signal with desired phase shift. Results show the RF phase shifter can achieve a continuous phase shift with low amplitude variation.

  18. Optical signal monitoring in phase modulated optical fiber transmission systems

    Science.gov (United States)

    Zhao, Jian

    there is a phase error (Deltaphi) in the delay interferometer (DI) and in the presence of residual CD. Using delay-tap sampling the scatter plots can reflect this signal distortion through their asymmetric characteristics. A distance ratio (DR) is defined to represent the change of the scatter plots which is directly related to the accumulated CD. The monitoring range can be up to +/-400ps/nm and to +/-720ps/nm for 10Gb/s NRZ-DPSK and RZ-DPSK signals with 450 phase error in DI. The monitoring sensitivity reaches +/-8ps/nm and CD polarity discrimination is realized. It is found that the signal degradation is related to the increment of the absolute value of CD or phase mismatch. The effect of different polarities of phase error on CD monitoring is also analyzed. The shoulders location depends on the sign of the product DLDeltaphi. If DLDeltaphi > 0, the shoulder will appear on trailing edge else the shoulder will appear on leading edge when DLDeltaphi < 0. The analysis shows that the phase error is identical to the frequency offset of optical source so a signed frequency offset monitoring is also demonstrated. The monitoring results show that the monitoring range can reach +/-2.2GHz and the monitoring sensitivity is around 27MHz. The effect of nonlinearity, OSNR and bandwidth of the lowpass filter on the proposed monitoring method has also been studied. The signed CD monitoring for 100Gb/s carrier suppressed return-to-zero differential quadrature phase-shift keying (CSRZ-DQPSK) system based on the delay-tap sampling technology is demonstrated. The monitoring range and monitoring resolution can goes up to +/-32ps/nm and +/-8ps/nm, respectively. A signed CD and optical carrier wavelength monitoring scheme using cross-correlation method for on-off keying (00K) wavelength division multiplexing (WDM) system is proposed and demonstrated. CD monitoring sensitivity is high and can be less than 10% of the bit period. Wavelength monitoring is implemented using the proposed

  19. Spectral changes induced by a phase modulator acting as a time lens

    Energy Technology Data Exchange (ETDEWEB)

    Plansinis, B. W. [Univ. of Rochester, Rochester, NY (United States). Inst. of Optics.; Donaldson, W. R. [Univ. of Rochester, Rochester, NY (United States). Lab. for Laser Energetics; Agrawal, G. P. [Univ. of Rochester, Rochester, NY (United States). Inst. of Optics; Univ. of Rochester, Rochester, NY (United States). Lab. for Laser Energetics.

    2015-07-06

    We show both numerically and experimentally that a phase modulator, acting as a time lens in the Fourier-lens configuration, can induce spectral broadening, narrowing, or shifts, depending on the phase of the modulator cycle. These spectral effects depend on the maximum phase shift that can be imposed by the modulator. In our numerical simulations, pulse spectrum could be compressed by a factor of 8 for a 30 rad phase shift. Experimentally, spectral shifts over a 1.35 nm range and spectral narrowing and broadening by a factor of 2 were demonstrated using a lithium niobate phase modulator with a maximum phase shift of 16 rad at a 10 GHz modulation frequency. All spectral changes were accomplished without employing optical nonlinear effects such as self- or cross-phase modulation.

  20. Simultaneous dispersion and non-linearity compensation with mid-span optical phase conjugation and distributed Raman amplifier for a sub-carrier multiplexed optical transmission link

    Science.gov (United States)

    Chandra, S.; Vardhanan, A. Vishnu; Gangopadhyay, R.

    2007-11-01

    Optical phase conjugation (OPC) and distributed Raman amplifier (DRA) combination (OPC-DRA) is demonstrated as a potential enabling solution for simultaneous reduction of fiber non-linearities and dispersion compensation of a sub-carrier multiplexed (SCM) optical transmission link. The present work is focused on the use of OPC-DRA combination for system performance improvement in terms of composite second order distortion (CSO) and carrier to noise ratio (CNR) of the SCM link. The analysis further shows that, introduction of DRA with proper pumping scheme significantly reduce fiber non-linearity resulting in improvement of the system performance in terms of CNR, compared to the situation where only mid-way optical phase conjugation is used.

  1. Mainstream Smoke Gas Phase Filtration Performance of Adsorption Materials Evaluated With A Puff-by-Puff Multiplex GC-MS Method

    Directory of Open Access Journals (Sweden)

    Xue L

    2014-12-01

    Full Text Available The mainstream smoke filtration performance of activated carbon, silica gel and polymeric aromatic resins for gas-phase components was evaluated using a puff-by-puff multiplex gas chromatography-mass spectrometry (GC-MS analysis method (1. The sample 1R4F Kentucky reference cigarettes were modified by placing the adsorbents in a plug/space/plug filter configuration. Due to differences in surface area and structural characteristics, the adsorbent materials studied showed different levels of filtration activities for the twenty-six constituents monitored. Activated carbon had significant adsorption activity for all the gas-phase smoke constituents observed except ethane and carbon dioxide, while silica gel had significant activities for polar components such as aldehydes, acrolein, ketones, and diacetyl. XAD-16 polyaromatic resins showed varied levels of activity for aromatic compounds, cyclic dienes and ketones.

  2. Multiplexing of spatial modes in the mid-IR region

    Science.gov (United States)

    Gailele, Lucas; Maweza, Loyiso; Dudley, Angela; Ndagano, Bienvenu; Rosales-Guzman, Carmelo; Forbes, Andrew

    2017-02-01

    Traditional optical communication systems optimize multiplexing in polarization and wavelength both trans- mitted in fiber and free-space to attain high bandwidth data communication. Yet despite these technologies, we are expected to reach a bandwidth ceiling in the near future. Communications using orbital angular momentum (OAM) carrying modes offers infinite dimensional states, providing means to increase link capacity by multiplexing spatially overlapping modes in both the azimuthal and radial degrees of freedom. OAM modes are multiplexed and de-multiplexed by the use of spatial light modulators (SLM). Implementation of complex amplitude modulation is employed on laser beams phase and amplitude to generate Laguerre-Gaussian (LG) modes. Modal decomposition is employed to detect these modes due to their orthogonality as they propagate in space. We demonstrate data transfer by sending images as a proof-of concept in a lab-based scheme. We demonstrate the creation and detection of OAM modes in the mid-IR region as a precursor to a mid-IR free-space communication link.

  3. QPSK Modulator with Continuous Phase and Fast Response Based on Phase-Locked Loop

    Directory of Open Access Journals (Sweden)

    L. Kirasamuthranon

    2017-06-01

    Full Text Available Among M-phase shift keying (M-PSK schemes, quadrature phase-shift keying (QPSK is used most often because of its efficient bandwidth consumption. However, in comparison with minimum-shift keying, which has continuous phase transitions, QPSK requires a higher bandwidth to transmit a signal. This article focuses on the phase transitions in QPSK signals, and a QPSK modulator based on a phase-locked loop (PLL is proposed. The PLL circuit in the proposed system differs from that of conventional PLL circuits because a three-input XOR gate and a summing circuit are used. With these additional components, the proposed PLL provides a continuous phase change in the QPSK signal. Consequently, the required bandwidth for transmitting the QPSK signal when using the proposed circuit is less than that for a conventional QPSK signal with a discontinuous phase. The analytical results for the proposed system in the time domain agree well with the experimental and simulation results of the circuit. Both the theoretical and experimental results thus confirm that the proposed technique can be realized in real-world applications.

  4. Analytical Assessment of the Q-Factor due to Cross-Phase Modulation (XPM)

    Institute of Scientific and Technical Information of China (English)

    Stephan; Pachnicke; Edgar; Voges

    2003-01-01

    The paper describes the impact of cross-phase modulation on NRZ modulated WDM systems. The impairments due to XPM will be related to a Q-factor and the effects of dispersion management will be covered.

  5. Quantitative EEG Signatures through Amplitude and Phase Modulation Patterns.

    Science.gov (United States)

    Myers, Mark H; Padmanabha, Akaash

    2017-01-01

    Cortical spatiotemporal signal patterns based on object recognition can be discerned from visual stimulation. These are in the form of amplitude modulation (AM) and phase modulation (PM) patterns, which contain perceptual information gathered from sensory input. A high-density Electroencephalograph (EEG) device consisting of 48 electrodes with a spacing of 5 mm was utilized to measure frontal lobe activity in order to capture event-related potentials from visual stimuli. Four randomized stimuli representing different levels of salient responsiveness were measured to determine if mild stimuli can be discerned from more extreme stimuli. AM/PM response patterns were detected between mild and more salient stimuli across participants. AM patterns presented distinct signatures for each stimulus. AM patterns had the highest number of incidents detected in the middle of the frontal lobe. Through this work, we can expand our encyclopedia of neural signatures to object recognition, and provide a broader understanding of quantitative neural responses to external stimuli. The results provide a quantitative approach utilizing spatiotemporal patterns to analyze where distinct AM patterns can be linked to object perception.

  6. Simulation of mm-wave signal generation using phase modulation in ROF system

    Institute of Scientific and Technical Information of China (English)

    ZHANG da-peng; YU Chong-xiu; XIN Xiang-jun; MA Jian-xin; ZHANG Jin-long

    2009-01-01

    The generation of optical millimeter waves via the improved phase modulator in a RoF system and the transmission char-acter of the signal are thenretically investigated. A new phase modulating scheme is proposed, in which the sidebands are separated by wave length demultiplexer and one of them doesn't feed digital signals, thereby the phase wake-off is restrained.

  7. DSP based coherent receiver for phase-modulated radio-over-fiber optical links

    DEFF Research Database (Denmark)

    Zibar, Darko; Tafur Monroy, Idelfonso; Peucheret, Christophe

    2008-01-01

    A novel DSP based coherent receiver for phase modulated radio-over-fiber optical links is reported. Using the proposed digital receiver, signal demodulation of 1.25 Gb/s ASK-modulated 10 GHz RF carrier is experimentally demonstrated.......A novel DSP based coherent receiver for phase modulated radio-over-fiber optical links is reported. Using the proposed digital receiver, signal demodulation of 1.25 Gb/s ASK-modulated 10 GHz RF carrier is experimentally demonstrated....

  8. Calibration of Two Difrerent Types of Modulators for an Application in Spectroscopic Phase Modulated Ellipsometry

    Science.gov (United States)

    Kouko, S. L.; Llinares, C.

    1995-08-01

    In order to choose a photoelastic modulator for an application in spectroscopic phase modulated ellipsometry a complete calibration of two different types of photoelastic modulators is achieved. First the model that describes the behavior of each of them is accurately determined since the calibration procedure depends on it. Both modulators behave as a static strain model with a phase shift of the form δ = δ_0 + {\\cal A}sin ω t. Using the suitable procedures, the driving voltage V_mod and the static strain δ_0 of both devices are accurately determined as a function of the wavelength from 0.25 μm to 0.75 μm. A method to reduce the errors due to incorrect settings of the modulation voltage and the static birefringence is also proposed. An accuracy check of the calibration done by comparing the indexes of refraction of two silica prisms obtained with our ellipsometer and with the high precision goniometer method shows a very good agreement. Dans le but de choisir un modulateur photoélastique pour une application en ellipsométrie spectroscopique à modulation de phase, le calibrage de deux modulateurs a été réalisé. Dans un premier temps, le modèle décrivant chacun des modulateurs a été déterminé avec précision vu que la procédure de calibrage dépend de celui-ci : les deux modulateurs fonctionnent suivant le modèle avec biréfringence statique ayant un déphasage de la forme δ = δ_0 + {\\cal A}sin ω t. En utilisant les procédures de calibrage appropriées, la tension de pilotage V_mod et la biréfringence statique δ_0 ont été déterminées avec précision en fonction de la longueur d'onde dans la gamme spectrale s'étendant de 0,25 μm à 0,75 μm. Une méthode pour réduire les erreurs dues au calibrage de la tension de modulation et à la biréfringence résiduelle est également proposée. Un test de la précision du calibrage fait en comparant les indices de réfraction de deux prismes de silice obtenus avec notre ellipsomètre et avec

  9. A novel lab-on-chip platform with integrated solid phase PCR and Supercritical Angle Fluorescence (SAF) microlens array for highly sensitive and multiplexed pathogen detection.

    Science.gov (United States)

    Hung, Tran Quang; Chin, Wai Hoe; Sun, Yi; Wolff, Anders; Bang, Dang Duong

    2017-04-15

    Solid-phase PCR (SP-PCR) has become increasingly popular for molecular diagnosis and there have been a few attempts to incorporate SP-PCR into lab-on-a-chip (LOC) devices. However, their applicability for on-line diagnosis is hindered by the lack of sensitive and portable on-chip optical detection technology. In this paper, we addressed this challenge by combining the SP-PCR with super critical angle fluorescence (SAF) microlens array embedded in a microchip. We fabricated miniaturized SAF microlens array as part of a microfluidic chamber in thermoplastic material and performed multiplexed SP-PCR directly on top of the SAF microlens array. Attribute to the high fluorescence collection efficiency of the SAF microlens array, the SP-PCR assay on the LOC platform demonstrated a high sensitivity of 1.6 copies/µL, comparable to off-chip detection using conventional laser scanner. The combination of SP-PCR and SAF microlens array allows for on-chip highly sensitive and multiplexed pathogen detection with low-cost and compact optical components. The LOC platform would be widely used as a high-throughput biosensor to analyze food, clinical and environmental samples.

  10. Extension of Measurable Region of Object Vibration Phasor in Phase-Modulated TV Holographic Interferometry: Experiment

    Science.gov (United States)

    Kojima, Kentaro; Miyazaki, Takeshi; Nojima, Ken; Yamamoto, Hirotaka; Sasaki, Yasuhito

    2004-03-01

    In this paper, we present an experiment based on the previously reported theory concerning the extension of the measurable region of object vibration phasor in phase-modulated TV holographic interferometry. This theory is based on the following facts: (1) the modulation of speckle interference image is proportional to the Bessel function, (2) its argument indicates the distance between the phasors of phase modulation and object vibration in the complex plane, and (3) the modulation increases as the Bessel function argument approaches zero. The phase modulation phasor is scanned, and at each pixel, one seeks the phase modulation phasor producing the maximum modulation. From the modulations produced by four phase modulation phasors adjacent to the sought phase modulation phasor, the object vibration phasor can be calculated. We analyzed the vibration of a phosphor-bronze rectangular plate with free sides, which were vibrated at the center by a piezoelectric transducer (PZT). Twenty-one phase modulation phasors were employed. The results of measurement were presented, and it was confirmed that the object vibration phasor can be measured in the wider region based on the theory concerning the extension of the measurable region.

  11. Multiplexed optical operation of distributed nanoelectromechanical systems arrays.

    Science.gov (United States)

    Sampathkumar, A; Ekinci, K L; Murray, T W

    2011-03-09

    We report a versatile all optical technique to excite and read-out a distributed nanoelectromechanical systems (NEMS) array. The NEMS array is driven by a distributed, intensity modulated optical pump through the photothermal effect. The ensuing vibrational response of the array is multiplexed onto a single probe beam in the form of a high frequency phase modulation. The phase modulation is optically down converted to a low frequency intensity modulation using an adaptive full-field interferometer, and subsequently detected using a CCD array. Rapid and single step mechanical characterization of ∼44 nominally identical high-frequency resonators is demonstrated. The technique may enable sensitivity improvements over single NEMS resonators by averaging signals coming from a multitude of devices in the array. In addition, the diffraction limited spatial resolution may allow for position-dependent read-out of NEMS sensor chips for sensing multiple analytes or spatially inhomogeneous forces.

  12. Frequency Modulation Induced by using the Linear Phase Modulation Method used in a Resonator Micro-optic Gyro

    Institute of Scientific and Technical Information of China (English)

    HONG Ling-Fei; ZHANG Chun-Xi; FENG Li-Shuang; YU Huai-Yong; LEI Ming

    2012-01-01

    Resonator micro-optic gyro (R-MOG) sensing rotation angular-velocity is based on Sagnac effect.We present a frequency modulation (FM) induced by the analog triangle-waveform phase modulation (ATAW-PM) technique in an R-MOG.Compared with the traditional serrodyne phase modulation or digital phase modulation methods,the proposed modulation technique has the intrinsic advantage in free of sweeping-back or step-effect induced pulse noise.The influence on dynamic range and resolution of the R-MOG by the parameters of analog trianglewaveform is theoretically analyzed.Experiments are carried out on an R-MOG composed of an integrated optic resonator with a free spectral range (FSR) and a fitness (F) of 1.6GHz and 61,respectively.Dynamic range of ±500 deg/s and bias drift of 0.6 deg/s over 1 h and 0.05 deg/s for 60 s are reliably obtained.%Resonator micro-optic gyro (R-MOG) sensing rotation angular-velocity is based on Sagnac effect. We present a frequency modulation (FM) induced by the analog triangle-waveform phase modulation (ATAW-PM) technique in an R-MOG. Compared with the traditional serrodyne phase modulation or digital phase modulation methods, the proposed modulation technique has the intrinsic advantage in free of sweeping-back or step-effect induced pulse noise. The influence on dynamic range and resolution of the R-MOG by the parameters of analog triangle-waveform is theoretically analyzed. Experiments are carried out on an R-MOG composed of an integrated optic resonator with a free spectral range (FSR) and a Btness (F) of 1.6 GHz and 61, respectively. Dynamic range of ±500 deg/s and bias drift of 0.6deg/s over 1 h and 0.05deg/s for 60s are reliably obtained.

  13. Fiber Attachment Module Experiment (FAME): Using a Multiplexed Miniature Hollow Fiber Membrane Bioreactor Solution for Rapid Process Testing

    Science.gov (United States)

    Lunn, Griffin; Wheeler, Raymond; Hummerick, Mary; Birmele, Michele; Richards, Jeffrey; Coutts, Janelle; Koss, Lawrence; Spencer, Lashelle.; Johnsey, Marissa; Ellis, Ronald

    Bioreactor research, even today, is mostly limited to continuous stirred-tank reactors (CSTRs). These are not an option for microgravity applications due to the lack of a gravity gradient to drive aeration as described by the Archimedes principle. This has led to testing of Hollow Fiber Membrane Bioreactors (HFMBs) for microgravity applications, including possible use for wastewater treatment systems for the International Space Station (ISS). Bioreactors and filtration systems for treating wastewater could avoid the need for harsh pretreatment chemicals and improve overall water recovery. However, the construction of these reactors is difficult and commercial off-the-shelf (COTS) versions do not exist in small sizes. We have used 1-L modular HFMBs in the past, but the need to perform rapid testing has led us to consider even smaller systems. To address this, we designed and built 125-mL, rectangular reactors, which we have called the Fiber Attachment Module Experiment (FAME) system. A polycarbonate rack of four square modules was developed with each module containing removable hollow fibers. Each FAME reactor is self-contained and can be easily plumbed with peristaltic and syringe pumps for continuous recycling of fluids and feeding, as well as fitted with sensors for monitoring pH, dissolved oxygen, and gas measurements similar to their larger counterparts. The first application tested in the FAME racks allowed analysis of over a dozen fiber surface treatments and three inoculation sources to achieve rapid reactor startup and biofilm attachment (based on carbon oxidation and nitrification of wastewater). With these miniature FAME reactors, data for this multi-factorial test were collected in duplicate over a six-month period; this greatly compressed time period required for gathering data needed to study and improve bioreactor performance.

  14. Design of a piezoelectric transducer cylindrical phase modulator for simulating acoustic emission signals

    Institute of Scientific and Technical Information of China (English)

    HE Cunfu; HANG Lijun; WU Bin

    2007-01-01

    To conveniently carry out the pipeline leak experiment in a laboratory,leak acoustic signals are simulated by using the converse piezoelectric effect of a piezoelectric transducer (PZT) cylindrical phase modulator.On the basis of the piezoelectric equations and electromechanical equivalence principle,the transfer function of a PZT cylindrical phase modulator is delivered.A PZT cylindrical phase modulator is designed,and the numerical simulation is conducted.Results prove that the PZT cylindrical phase modulator can effectively simulate leak acoustic emission signals when the frequency is lower than 25 KHz.

  15. Bond percolation on multiplex networks

    CERN Document Server

    Hackett, A; Gómez, S; Arenas, A; Gleeson, J P

    2015-01-01

    We present an analytical approach for bond percolation on multiplex networks and use it to determine the expected size of the giant connected component and the value of the critical bond occupation probability in these networks. We advocate the relevance of these tools to the modeling of multilayer robustness and contribute to the debate on whether any benefit is to be yielded from studying a full multiplex structure as opposed to its monoplex projection, especially in the seemingly irrelevant case of a bond occupation probability that does not depend on the layer. Although we find that in many cases the predictions of our theory for multiplex networks coincide with previously derived results for monoplex networks, we also uncover the remarkable result that for a certain class of multiplex networks, well described by our theory, new critical phenomena occur as multiple percolation phase transitions are present. We provide an instance of this phenomenon in a multipex network constructed from London rail and Eu...

  16. Waveguide Phase Modulator for Integrated Planar Lightwave Circuits in KTP Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This SBIR Phase I effort proposes the development of a potassium titanyl phosphate (KTP) waveguide phase modulator for future integration into a Planar Lightwave...

  17. Phase-modulated shaping of narrowband type-I parametric down-converted photons

    CERN Document Server

    Joseph1, A T; Pike2, E R; Sarkar2, S

    2006-01-01

    We present a general theoretical description of the temporal shaping of narrowband noncollinear type-I down-converted photons using a spectral phase filter with a symmetric phase distribution. By manipulating the spectral phase of the signal or idler photon, we demonstrate control of the correlation time and shape of the two-photon wave function with modulation frequency and modulation depth of the phase distribution.

  18. Conversion of a transverse density modulation into a longitudinal phase space modulation using an emittance exchange technique

    CERN Document Server

    Sun, Y -E; Johnson, A; Lumpkin, A; Ruan, J; Thurman-Keup, R

    2010-01-01

    We report on an experiment to produce a train of sub-picosecond microbunches using a transverse-to-longitudinal emittance exchange technique. The generation of a modulation on the longitudinal phase space is done by converting an initial horizontal modulation produced using a multislits mask. The preliminary experimental data clearly demonstrate the conversion process. To date only the final energy modulation has been measured. However numerical simulations, in qualitative agreement with the measurements, indicate that the conversion process should also introduce a temporal modulation.

  19. Enhanced Cross-Phase Modulation via Phase Control in a Quantum dot Nanostructure

    Institute of Scientific and Technical Information of China (English)

    郝向英; 郑安寿; 王英; 李小刚

    2012-01-01

    A four-level quantum dot (QD) nanostructure interacting with four fields (two weak near-infrared (NIR) pulses and two control fields) forms the well-known double-cascade configuration.We investigate the cross-phase modulation (XPM) between the two NIR pulses.The results show,in such a closed-loop scheme,that the XPM can be greatly enhanced,while the linear absorption and two-photon absorption (gain) can be efficiently depressed by tuning the relative phase among the applied fields.This protocol may have potential applications in NIR all-optical switch design and quantum information processing with the solid-state materials.

  20. 80-GB all-optical serial-to-parallel convertor for QPSK signal based on cascaded phase modulators and optical filters

    Institute of Scientific and Technical Information of China (English)

    Deming Kong; Yan Li; Hui Wang; Jian Wu; Jintong Lin

    2012-01-01

    An all-optical serial-to-parallel converter (SPC) utilizing two cascaded phase modulators and optical bandpass filters (OBPFs) is experimentally investigated and applied to demultiplex an 80-GBd optical timedivision multiplexing (OTDM) return-to-zero (RZ) differential quadrature phase-shift keying (QPSK) signal.Two 40-GBd OTDM tributaries are error-free demultiplexed with a power penalty of approximately 4 dB in the worst case.With its advantages of compact structure,high speed,low power penalty,simultaneous two-tributary operation,and no assistance from a light source,the SPC has potential for use in future OTDM networks.However,the performance of the SPC still needs improvement.

  1. Optimization of Generation and Detection of WDM Signals with Advanced Modulation Formats

    Institute of Scientific and Technical Information of China (English)

    Sarah; Dods

    2003-01-01

    This paper presents optimal generation and detection of wavelength division multiplexed (WDM) signals with advanced modulation formats. We investigate the relative phase alignment between phase modulation and data bits for chirped return-to-zero (CRZ) signals, and the frequency offset between the RZ carrier and various optical filters for vestigial side band (VSB)-RZ signals.

  2. Corticospinal modulations during bimanual movement with different relative phases

    Directory of Open Access Journals (Sweden)

    Yoshifumi eNomura

    2016-03-01

    Full Text Available The purpose of this study was to investigate corticospinal modulation of bimanual movement with different relative phases (RPs. The participants rhythmically abducted and adducted the right index finger (unimanual movement or both index fingers (bimanual movement with a cyclic duration of 1 s. The RP of bimanual movement, defined as the time difference between one hand movement and the other hand movement, was 0°, 90°, or 180°. Motor evoked potentials in the right flexor dorsal interosseous muscle elicited by transcranial magnetic stimulation were obtained during unimanual or bimanual movement. Corticospinal excitability in the first dorsal interosseous muscle during bimanual movement with 90° RP was higher than that during unimanual movement or bimanual movement with 0° or 180° RP. The correlation between muscle activity level and corticospinal excitability during bimanual movement with 90° RP was smaller than that during unimanual movement or bimanual movement with 0° or 180° RP. The higher corticospinal excitability during bimanual movement with 90° RP may be caused by the greater effort expended to execute a difficult task, the involvement of interhemispheric interaction, a motor binding process, or task acquisition. The lower dependency of corticospinal excitability on the muscle activity level during bimanual movement with 90° RP may reflect the minor corticospinal contribution to bimanual movement with an RP that is not in the attractor state.

  3. L2 Orthogonal Space Time Code for Continuous Phase Modulation

    CERN Document Server

    Hesse, Matthias; Deneire, Luc

    2008-01-01

    To combine the high power efficiency of Continuous Phase Modulation (CPM) with either high spectral efficiency or enhanced performance in low Signal to Noise conditions, some authors have proposed to introduce CPM in a MIMO frame, by using Space Time Codes (STC). In this paper, we address the code design problem of Space Time Block Codes combined with CPM and introduce a new design criterion based on L2 orthogonality. This L2 orthogonality condition, with the help of simplifying assumption, leads, in the 2x2 case, to a new family of codes. These codes generalize the Wang and Xia code, which was based on pointwise orthogonality. Simulations indicate that the new codes achieve full diversity and a slightly better coding gain. Moreover, one of the codes can be interpreted as two antennas fed by two conventional CPMs using the same data but with different alphabet sets. Inspection of these alphabet sets lead also to a simple explanation of the (small) spectrum broadening of Space Time Coded CPM.

  4. A review of single-phase grid-connected inverters for photovoltaic modules

    DEFF Research Database (Denmark)

    Kjaer, Soren Baekhoej; Pedersen, John Kim; Blaabjerg, Frede

    2005-01-01

    This review focuses on inverter technologies for connecting photovoltaic (PV) modules to a single-phase grid. The inverters are categorized into four classifications: 1) the number of power processing stages in cascade; 2) the type of power decoupling between the PV module(s) and the single...

  5. Cognitive digital receiver for burst mode phase modulated radio over fiber links

    DEFF Research Database (Denmark)

    Guerrero Gonzalez, Neil; Zibar, Darko; Tafur Monroy, Idelfonso

    2010-01-01

    A novel cognitive receiver for modulation format recognition with reconfigurable carrier recovery scheme is proposed and experimentally demonstrated for phase modulated radio-over-fibre links. Demodulation of burst-mode mixed modulation formats (PSK and QAM) is demonstrated after 40km...

  6. All-optical $\\mathcal{PT}$-symmetric amplitude to phase modulator

    CERN Document Server

    Gutiérrez, Oscar Ignacio Zaragoza; Rodríguez-Lara, B M

    2015-01-01

    We study electromagnetic field propagation through a planar three-waveguide coupler with linear gain and loss, in a configuration that is the optical analog of a quantum $\\mathcal{PT}$-symmetric system, and provide its closed-form analytic propagator. At an specific propagation length, we show that the device provides all-optical amplitude to phase modulation with a $\\pi$ modulation range, if an extra binary phase is allowed in the reference signal, as well as phase to amplitude modulation, with an amplitude modulation range that depends linearly on the gain-to-coupling ratio of the system.

  7. A novel modulation and direct detection scheme of optical phase shift keying

    Institute of Scientific and Technical Information of China (English)

    Yongcai Yang(杨永才); Wolfgang Vogel

    2004-01-01

    This paper introduces a new modulation and direct detection scheme of optical phase shift keying (PSK)which is simple and practical in fiber optical communication. A phase modulator is used to modulate a continuous wave (CW) laser source and return-to-zero (RZ) signal that is changed from the initial transmitting information is used to control a phase modulator to form a optical PSK signal. In the receiver terminal, just add a signal delayed a half of one bit to itself so that the initial information can be restored.

  8. A robust optical phase modulated 60 GHz RoF WDM system

    DEFF Research Database (Denmark)

    Yu, Xianbin; Kozuch, Wojciech; Turkiewicz, Jaroslaw

    2010-01-01

    robust 4-channel WDM optical phase modulated 60GHz wireless fiber system is proposed and simulated. In this system, a Fabry-Perot (FP) frequency interleaver is designed to suppress optical carriers for 60GHz signal generation. The simulated results show that this phase modulated WDM system...

  9. Affects of binary and continuous phase modulations on the structure of Bessel beams

    CSIR Research Space (South Africa)

    Dudley, Angela L

    2010-09-01

    Full Text Available The authors implement a novel technique to operate a phase-only spatial light modulator (SLM) in amplitude mode, allowing them to reproduce Durnin’s ring slit on a liquid crystal display (LCD). The affects of binary and continuous phase modulations...

  10. Nonlinearity and Phase Noise Tolerant 75-110 GHz Signal over Fiber System Using Phase Modulation Technique

    DEFF Research Database (Denmark)

    Deng, Lei; Pang, Xiaodan; Zhang, Xu

    2013-01-01

    We report on the transmission of 8 Gb/s 0 dB PAPR 16QAM-OFDM W-band (75-110 GHz) signals over 22.8km SMF without phase noise compensation by using a phase modulator in the optical heterodyne up-convertor.......We report on the transmission of 8 Gb/s 0 dB PAPR 16QAM-OFDM W-band (75-110 GHz) signals over 22.8km SMF without phase noise compensation by using a phase modulator in the optical heterodyne up-convertor....

  11. Phase-dependent modulation of percutaneously elicited multisegmental muscle responses after spinal cord injury

    OpenAIRE

    Dy, Christine J.; Gerasimenko, Yury P.; Edgerton, V Reggie; Dyhre-Poulsen, Poul; Courtine, Grégoire; Harkema, Susan J.

    2010-01-01

    Phase-dependent modulation of monosynaptic reflexes has been reported for several muscles of the lower limb of uninjured rats and humans. To assess whether this step-phase-dependent modulation can be mediated at the level of the human spinal cord, we compared the modulation of responses evoked simultaneously in multiple motor pools in clinically complete spinal cord injury (SCI) compared with noninjured (NI) individuals. We induced multisegmental responses of the soleus, medial gastrocnemius,...

  12. Correlated Edge Overlaps in Multiplex Networks

    CERN Document Server

    Baxter, Gareth J; da Costa, Rui A; Dorogovtsev, Sergey N; Mendes, José F F

    2016-01-01

    We develop the theory of sparse multiplex networks with partially overlapping links based on their local tree-likeness. This theory enables us to find the giant mutually connected component in a two-layer multiplex network with arbitrary correlations between connections of different types. We find that correlations between the overlapping and non-overlapping links markedly change the phase diagram of the system, leading to multiple hybrid phase transitions. For assortative correlations we observe recurrent hybrid phase transitions.

  13. Modulated liquid-crystal phases induced by polarity: Twist-bend, splay-bend, and blue phases

    Science.gov (United States)

    Selinger, Jonathan; Shamid, Shaikh; Allender, David

    2014-03-01

    Nematic liquid crystals exhibit flexoelectric couplings between polar order and gradients in the director field. When the couplings become strong enough, the uniform nematic phase can become unstable to the formation of a modulated polar phase. The question is then: What is the structure of the modulated polar phase? Classic work by Meyer and further studies by Dozov predicted two possible structures, known as twist-bend and splay-bend. One of these predictions, the twist-bend phase, has recently been identified in experiments on bent-core liquid crystals. Here, we investigate modulated polar phases through a combination of Landau theory and lattice simulations. We find a range of possibilities, including the twist-bend and splay-bend phases as well as polar blue phases, with 2D or 3D modulations of the director field and the polar order. We compare these polar blue phases with chiral blue phases, and discuss opportunities for observing them experimentally. Supported by NSF DMR-1106014.

  14. Optimize the modulation response of twisted-nematic liquid crystal displays as pure phase spatial light modulators

    Science.gov (United States)

    Ma, Baiheng; Peng, Fei; Kang, Mingwu; Zhou, Jiawu

    2014-11-01

    Twisted-nematic liquid crystal displays (TN-LCD) are widely used in numerous research fields of optics working as spatial light modulators. Approaches to obtaining desired intensity or phase modulation by TN-LCD have been extensively studied based on the knowledge of TN-LCD's internal structure parameters, e.g., the orientation of LC molecules at the surfaces, the twist angle, the thickness of the LC layer, and the birefringence of the material. Generally TN-LCD placed between two linear polarizers (P) produces coupled intensity and phase modulation. To obtain the commonly used pure phase modulation, quarter wave plates (QWP) are often used in front of and/or behind the LCD. In this paper, we present a method to optimize the optical modulation properties of the TN-LCD to obtain pure phase modulation in the configuration of P-QWP-LCD-QWP-P each with proper orientation. Firstly an improved method for determining the Jones matrix of the TN-LCD without knowing its internal parameters is presented, which is based on the macroscopical Jones matrix descriptions for TN-LCD, linear polarizer and QWP. Only three sets of intensity measurements are needed for the complete determination of the TN-LCD's Jones matrix for a single wavelength. Then Jones matrix calculations are carried out to determine the orientations of the polarizers and QWPs for pure phase modulation response. In addition, we prove that the phase modulation depth (PMD) of the TN-LCD can be further increased provided that the mean intensity transmission is decreased to a lower level, which is very useful when the TN-LCD is used as a phase modulator and the ratio between the intensities of the desired diffracted order relative to the other diffracted orders is required higher. Experimental results coincide well with the optical modulation properties of the TN-LCD predicted by our determined Jones matrix. In contrast to the traditional method which requires knowledge of the TN-LCD's internal structure parameters

  15. Suppression of phase-induced intensity noise in fibre optic delay line signal processors using an optical phase modulation technique.

    Science.gov (United States)

    Chan, Erwin H W

    2010-10-11

    A technique that can suppress the dominant phase-induced intensity noise in fibre optic delay line signal processors is presented. It is based on phase modulation of the optical carrier to distribute the phase noise at the information band into a high frequency band which can be filtered out. This technique is suitable for suppressing the phase noise in various delay line structures and for integrating in the conventional fibre optic links. It can also suppress the coherent interference effect at the same time. A model for predicting the amount of phase noise reduction in various delay line structures using the optical phase modulation technique is presented for the first time and is experimentally verified. Experimental results demonstrate the technique can achieve a large phase noise reduction in various fibre optic delay line signal processors.

  16. 一种光正交频分复用系统的联合相位均衡方法%Joint Phase Equalization in Optical Orthogonal Frequency Division Multiplexing System

    Institute of Scientific and Technical Information of China (English)

    高丽娜; 刘剑飞; 曾祥烨; 姜伟虎

    2012-01-01

    The combination of orthogonal frequency division multiplexing (OFDM) technology, coherent receiver and digital singal processing (DSP) is one of the ideal models in long-haul communication. However, optical OFDM receiver is sensitive to phase noise, so it is necessary to compensate phase noise for optical OFDM systems. A joint phase equalization solution to optical OFDM system based on orthogonal wavelet transform is proposed. In this method, block pilots are periodically inserted into the frame of OFDM signals. At receiver, the phase rotations of pilots are extracted to eliminate common phase difference of each subcarrier. Then, an adaptive equalization is applied to eliminate the phase error inside each subcarrier. Simulation results demonstrate that the proposed method is effective for 100 Gb/s optical binary translation quadrature amplitude modulation (4QAM) OFDM system in which data transmitted over 1000 km with G.652 fiber.%正交频分复用(OFDM)技术加相干接收与数字信号处理法(DSP)的组合是超长距离光通信的理想模型.光OFDM系统对相位噪声十分敏感,必须对相位噪声进行补偿.提出一种基于正交小波基变换的光OFDM系统的联合相位均衡方案.该方案将块状导频周期性地插入OFDM信号,在接收端利用导频信息首先消除各个子载波的公共相位误差,然后采用自适应均衡方式消除每个子载波自身相位误差.仿真结果表明,对于二进制正交振幅键控(4QAM)调制信号,在采用常规的G.652光纤、100 Gb/s的相干光OFDM系统中,该联合相位补偿方法可使信号在满足传输系统的误码性能要求下,传输距离达到1000 km.

  17. 2  ×  2 multiple-input multiple-output optical-wireless integration system based on optical independent-sideband modulation enabled by an in-phase/quadrature modulator.

    Science.gov (United States)

    Li, Xinying; Yu, Jianjun

    2016-07-01

    We propose a novel and simple 2×2 multiple-input multiple-output (MIMO) optical-wireless integration system, in which optical independent-sideband modulation enabled by an in-phase/quadrature (I/Q) modulator, instead of optical polarization multiplexing, is used to assist the simultaneous generation of two wireless millimeter-wave (mm-wave) signals. Software-based digital signal processing is used to generate the driving signal for the I/Q modulator, the output of which is two independent single-sideband optical vector signals located at two sides of a large central optical carrier. Based on our proposed 2×2 MIMO optical-wireless integration system, we experimentally demonstrate the simultaneous generation and 2×2 MIMO wireless delivery of two independent 40-GHz quadrature-phase-shift-keying (QPSK) wireless mm-wave signals. Each 40-GHz QPSK wireless mm-wave signal can carry up to 4-Gbaud transmitter data with a bit-error ratio less than the hard-decision forward-error-correction threshold of 3.8×10-3.

  18. A Time-Multiplexed Track-Trigger architecture for CMS

    CERN Document Server

    Hall, Geoffrey; Pesaresi, Mark Franco; Rose, A

    2014-01-01

    The CMS Tracker under development for the High Luminosity LHC includes an outer tracker based on ``PT-modules'' which will provide track stubs based on coincident clusters in two closely spaced sensor layers, aiming to reject low transverse momentum track hits before data transmission to the Level-1 trigger. The tracker data will be used to reconstruct track segments in dedicated processors before onward transmission to other trigger processors which will combine tracker information with data originating from the calorimeter and muon detectors, to make the final L1 trigger decision. The architecture for processing the tracker data is still an open question. One attractive option is to explore a Time Multiplexed design similar to one which is currently being implemented in the CMS calorimeter trigger as part of the Phase I trigger upgrade. The Time Multiplexed Trigger concept is explained, the potential benefits of applying it for processing future tracker data are described and a possible design based on cur...

  19. 160-Gb/s polarization-multiplexing optical NRZ-DQPSK transmission using differential detection

    Institute of Scientific and Technical Information of China (English)

    He Wen; Jinxin Liao; Xiaoping Zheng; Hanyi Zhang

    2011-01-01

    Using differential detection,we perform polarization-multiplexing 160-Gb/s optical non-return-to-zero (NRZ) differential quadrature phase shift keying (DQPSK) signal transmission over 100-km standard single mode fiber at a bit error rate (BER) of less than 10-9.The enabling technology includes clock recovery,fine dispersion compensation,and polarization tracking for de-multiplexing.Furthermore,a hybrid clock recovery scheme is proposed.The scheme is realized with ordinary devices using an optoelectrical modulator to down-convert the clock frequency and a phase-locked loop for filtering,which can provide an indication signal that simultaneouslv monitors residual disoersion and tracking polarization.Given the ever increasing bandwidth demands (e.g.,for imaging,demand of video,gaming,etc.),the capacity of optical transmission systems is being constantly raised through the application of several approaches that include the use of advanced modulation formats with higher spectral efficiency,increasing the symbol rate of each channel,and orthogonal polarization multiplexing with idcntical wavelengths;these approaches are enabled by coherent detection[1-3].%Using differential detection, we perform polarization-multiplexing 160-Gb/s optical non-return-to-zero (NRZ) differential quadrature phase shift keying (DQPSK) signal transmission over 100-km standard single mode fiber at a bit error rate (BER) of less than 10~9. The enabling technology includes clock recovery, fine dispersion compensation, and polarization tracking for de-multiplexing. Furthermore, a hybrid clock recovery scheme is proposed. The scheme is realized with ordinary devices using an optoclectrical modulator to down-convert the clock frequency and a phase-locked loop for filtering, which can provide an indication signal that simultaneously monitors residual dispersion and tracking polarization.

  20. Automated procedures for the assembly of the CMS Phase 1 upgrade pixel modules

    Science.gov (United States)

    Wade, Alex; CMS Collaboration

    2016-03-01

    The Phase 1 upgrade of the pixel tracker for the CMS experiment requires the assembly of approximately 1000 modules consisting of pixel sensors bump bonded to readout chips. The precision assembly of modules in this volume is made possible using several robotic processes for dispensing epoxy,positioning of sensor components, automatic wire-bonding and robotic deposition of elastomer for wire bond encapsulation. We will describe the these processes in detail, along with the measurements that quanitfy the quality of assembled modules, and describe the subsequent steps in which the sensor modules are used in the construction of the Phase 1 pixel tracker. With support from USCMS.

  1. Impact of Spectral Filter on Phase Modulation Pulse in Fiber Front End System

    Institute of Scientific and Technical Information of China (English)

    LI Jing; JING Feng; WANG Jian-Jun; XU Dang-Peng; LIN Hong-Huan; GENG Yuan-Chao; LI Ming-Zhong; DENG Ying; ZHU Na; ZHANG Rui

    2011-01-01

    The transmission characteristics of phase modulation pulse transmitted through the filter in the power amplifier are investigated theoretically and experimentally. The narrow bandpass filter can induce large temporal modula-tion depth for the phase modulation pulse and induce double amplitude modulation(AM)if the frequency shift is lower than half bandwidth of the signal spectrum. We should choose a wider bandwidth filter to minimize the impact of the filter on the output pulse and suppress the amplified spontaneous emission(ASE) for the power fiber amplifier. These results are of benefit to the design of the fiber front end system.

  2. Phase retrieval based on cosine grating modulation and transport of intensity equation

    Science.gov (United States)

    Chen, Ya-ping; Zhang, Quan-bing; Cheng, Hong; Qian, Yi; Lv, Qian-qian

    2016-10-01

    In order to calculate the lost phase from the intensity information effectively, a new method of phase retrieval which based on cosine grating modulation and transport of intensity equation is proposed. Firstly, the cosine grating is loaded on the spatial light modulator in the horizontal and vertical direction respectively, and the corresponding amplitude of the light field is modulated. Then the phase is calculated by its gradient which is extracted from different direction modulation light illumination. The capability of phase recovery of the proposed method in the presence of noise is tested by simulation experiments. And the results show that the proposed algorithm has a better resilience than the traditional Fourier transform algorithm at low frequency noise. Furthermore, the phase object of different scales can be retrieved using the proposed algorithm effectively by changing the frequency of cosine grating, which can control the imaging motion expediently.

  3. Walking phase modulates H-reflex amplitude in flexor carpi radialis.

    Science.gov (United States)

    Domingo, Antoinette; Klimstra, Marc; Nakajima, Tsuyoshi; Lam, Tania; Hundza, Sandra R

    2014-01-01

    It is well established that remote whole-limb rhythmic movement (e.g., cycling or stepping) induces suppression of the Hoffman (H-) reflex evoked in stationary limbs. However, the dependence of reflex amplitude on the phase of the movement cycle (i.e., phase-dependence) has not been consistent across this previous research. The authors investigated the phase-dependence of flexor carpi radialis (FCR) H-reflex amplitudes during active walking and in kinematically matched static postures across the gait cycle. FCR H-reflexes were elicited in the stationary forearm with electrical stimulation to the median nerve. Significant phase-dependent modulation occurred during walking when the gait cycle was examined with adequate phase resolution. The suppression was greatest during midstance and midswing, suggesting increased ascending communication during these phases. There was no phase-dependent modulation in static standing postures and no correlation between lower limb background electromyography levels and H-reflex amplitude during active walking. This evidence, along with previous research demonstrating no phase modulation during passive walking, suggests that afferent feedback associated with joint position and leg muscle activation levels are not the sole source of the phase modulation seen during active walking. Possible sources of phase modulation include combinations of afferent feedback related to active movement or central motor commands or both.

  4. Three-Phase Modulated Pole Machine Topologies Utilizing Mutual Flux Paths

    DEFF Research Database (Denmark)

    Washington, Jamie G.; Atkinson, Glynn J.; Baker, Nick J.

    2012-01-01

    This paper discusses three-phase topologies for modulated pole machines (MPMs). The authors introduce a new threephase topology, which takes advantage of mutual flux paths; this is analyzed using 3-D finite-element methods and compared to a three-phase topology using three single-phase units...... both performance and constructional benefits over prior MPM topologies....

  5. Photonic downconversion for coherent phase-modulated radio-over-fiber links using free-running local oscillator

    DEFF Research Database (Denmark)

    Caballero Jambrina, Antonio; Zibar, Darko; Schäffer, Christian G.

    2011-01-01

    A digital coherent receiver employing photonic downconversion is presented and experimentally demonstrated for phase-modulated radio-over-fiber optical links. Photonic downconversion adds additional advantages to optical phase modulated links by allowing demodulation of signals with RF carrier...

  6. Suppression of stimulated Brillouin scattering with phase modulator in soliton pulse compression

    Institute of Scientific and Technical Information of China (English)

    Bo Lü; Taorong Gong; Ming Chen; Muguang Wang; Tangjun Li; Genxiang Chen; Shuisheng Jian

    2009-01-01

    A phase modulator is employed in the scheme of soliton pulse compression with dispersion shifted fiber (DSF). Stimulated Brillouin scattering (SBS) effect, as a negative influence here, can be dramatically suppressed after optical phase modulation. The experimental result shows that the launched power required for high-order soliton pulse compression has been significantly increased by 11 dB under the condition of 100-MHz phase modulation. Accordingly, the experiment of picosecond pulse compression generated from electro-absorption sampling window (EASW) has also been implemented.

  7. Modulated magnetic phase of structurally heterogeneous easy-plane weak ferromagnets

    Science.gov (United States)

    Dzhuraev, D. R.; Niyazov, L. N.; Sokolov, B. Yu.

    2016-06-01

    The modulated magnetic phase of a structurally heterogeneous easy-plane weak ferromagnet is considered in terms of the thermodynamic Landau theory of phase transitions. The temperature and field dependences of the main magnetic order modulation parameters are determined. The results obtained are compared with the experimental data obtained for the orientational phase transition into a modulated magnetic state that occurs in hematite and iron borate crystals doped with diamagnetic ions to create structural heterogeneity. The proposed theoretical model is shown to describe the entire set of experimental results consistently with some exceptions.

  8. Hyperresolving phase-only filters with an optically addressable liquid crystal spatial light modulator.

    Science.gov (United States)

    McOrist, J; Sharma, M D; Sheppard, C J R; West, E; Matsuda, K

    2003-01-01

    Hyperresolving (sometimes called 'superresolving' or 'ultraresolving') phase-only filters can be generated using an optically addressable liquid crystal spatial light modulator. This approach avoids the problems of low efficiency, and coupling between amplitude and phase modulation, that arise when using conventional liquid crystal modulators. When addressed by a programmed light intensity distribution, it allows filters to be changed rapidly to modify the response of a system or permit the investigation of different filter designs. In this paper we present experimental hyperresolved images obtained using an optically addressable parallel-aligned nematic LCD with two zone Toraldo type phase-only filters. The images are compared with theoretical predictions.

  9. Gauss linear frequency modulation wavelet transforms and its application to seismic phases identification

    Institute of Scientific and Technical Information of China (English)

    刘希强; 周惠兰; 曹文海; 李红; 李永红; 季爱东

    2002-01-01

    Based on the characteristics of gradual change style seismic signal onset which has more high frequency signal components but less magnitude, this paper selects Gauss linear frequency modulation wavelet as base function to study the change characteristics of Gauss linear frequency modulation wavelet transform with difference wavelet and signal parameters, analyzes the error origin of seismic phases identification on the basis of Gauss linear frequency modulation wavelet transform, puts forward a kind of new method identifying gradual change style seismic phases with background noise which is called fixed scale wavelet transform ratio, and presents application examples about simulation digital signal and actual seismic phases recording onsets identification.

  10. Supercontinuum Generation Enhanced by Cross-phase Modulation in Dispersion-flattened and Decreasing Fiber

    Institute of Scientific and Technical Information of China (English)

    XU Wen-cheng; XU Yong-zhao; YU Bing-tao; CUI Hu; CHEN Yong-zhu; LIU Song-hao

    2005-01-01

    Supercontinuum spectrum generation in a dispersion-flattened and decreasing fiber with two orthogonally polarized pulses was simulated and calculated. The research results indicated that the supercontinuum spectrum generated by two orthogonally polarized pulses is wider and flatter than that generated by single polarized pulse due to cross-phase modulation. The cross-phase modulation effect can enhance the supercontinuum spectrum generation. When the pump power of the input pulse is lower, the enhancement of supercontinuum spectrum generation by cross-phase modulation effect is more significant.

  11. Multiplex Solid-Phase PCR for Rapid Detection and Identification of Salmonella spp. at Sub-species

    DEFF Research Database (Denmark)

    Cao, Cuong; Høgberg, Jonas; Wolff, Anders

    -PCR gel electrophoresis. The method will be useful for development of point-of-care devices for rapid detection and identification of Salmonella spp. A solid-phase PCR for rapid detection and identification of S. enteritidis, S. typhimurium and S. dublin is developed. The method offers advantages......This study presents a solid-phase PCR (SP-PCR) for rapid detection, identification, and sub-typing of various Salmonella species, the major food-borne cause of salmonellosis. The target DNA is firstly amplified with PCR primers (one primer is labeled with fluorophores) in the liquid phase...... by the liquid phase primer thus generating new templates for the SP-PCR. After the reaction, PCR products labeled with fluorophores remain attached to the substrate and can be visualized directly by fluorescence readout devices. Using this method, S. enteritidis, S. typhimurium and S. dublin can be detected...

  12. Phase-dependent modulation of percutaneously elicited multisegmental muscle responses after spinal cord injury.

    Science.gov (United States)

    Dy, Christine J; Gerasimenko, Yury P; Edgerton, V Reggie; Dyhre-Poulsen, Poul; Courtine, Grégoire; Harkema, Susan J

    2010-05-01

    Phase-dependent modulation of monosynaptic reflexes has been reported for several muscles of the lower limb of uninjured rats and humans. To assess whether this step-phase-dependent modulation can be mediated at the level of the human spinal cord, we compared the modulation of responses evoked simultaneously in multiple motor pools in clinically complete spinal cord injury (SCI) compared with noninjured (NI) individuals. We induced multisegmental responses of the soleus, medial gastrocnemius, tibialis anterior, medial hamstring, and vastus lateralis muscles in response to percutaneous spinal cord stimulation over the Th11-Th12 vertebrae during standing and stepping on a treadmill. Individuals with SCI stepped on a treadmill with partial body-weight support and manual assistance of leg movements. The NI group demonstrated phase-dependent modulation of evoked potentials in all recorded muscles with the modulation of the response amplitude corresponding with changes in EMG amplitude in the same muscle. The SCI group demonstrated more variation in the pattern of modulation across the step cycle and same individuals in the SCI group could display responses with a magnitude as great as that of modulation observed in the NI group. The relationship between modulation and EMG activity during the step cycle varied from noncorrelated to highly correlated patterns. These findings demonstrate that the human lumbosacral spinal cord can phase-dependently modulate motor neuron excitability in the absence of functional supraspinal influence, although with much less consistency than that in NI individuals.

  13. Equalization Technique for Balancing the Modulation Ratio Characteristics of the Single-Phase-to-Three-Phase Matrix Converter

    Directory of Open Access Journals (Sweden)

    Vengadeshwaran Velu

    2016-01-01

    Full Text Available Three-phase system has numerous advantages over the single-phase system in terms of instantaneous power, stability, and cost. Three-phase systems are not available in every location particularly in remote rural areas, hill stations, low voltage distribution homes, and so forth. Having a system that is capable of converting directly the readily available single-phase system to three phases will have greater usability in various applications. The routine techniques adopted in the direct ac-ac single-phase-to-three-phase converters do not yield the best desired outputs because of their complexity in the segregation process and bidirectional nature of the input signal. Other initiatives use ac-dc-ac converters which are huge and costly due to dc link energy storage devices. Further, none of these systems provide a convincing result in producing the standard three-phase output voltages that are 120° away from each other. This paper proposes an effective direct ac-ac single-phase-to-three-phase conversion technique based on space vector pulse width modulation based matrix converter system that produces a convincing three-phase output signals from a single-phase source with balanced modulation index characteristics. The details of the scientific programming adopted on the proposed technique were presented.

  14. 160 Gb/s Silicon All-Optical Data Modulator based on Cross Phase Modulation

    DEFF Research Database (Denmark)

    Hu, Hao; Pu, Minhao; Ji, Hua

    2012-01-01

    We have demonstrated 160 Gb/s all-optical data modulation with an extinction ratio of 18.5 dB based on XPM in a silicon nanowire. Error free performance is achieved for the optically modulated 160 Gb/s signal.......We have demonstrated 160 Gb/s all-optical data modulation with an extinction ratio of 18.5 dB based on XPM in a silicon nanowire. Error free performance is achieved for the optically modulated 160 Gb/s signal....

  15. Phase Noise Influence in Optical OFDM Systems employing RF Pilot Tone for Phase Noise Cancellation

    OpenAIRE

    Jacobsen, Gunnar; Kazovsky, Leonid G.; Xu, TianHua; Popov, Sergei; Li, Jie; Zhang, Yimo; Friberg, Ari T.

    2016-01-01

    For coherent and direct-detection Orthogonal Frequency Division Multiplexed (OFDM) systems employing radio frequency (RF) pilot tone phase noise cancellation the influence of laser phase noise is evaluated. Novel analytical results for the common phase error and for the (modulation dependent) inter carrier interference are evaluated based upon Gaussian statistics for the laser phase noise. In the evaluation it is accounted for that the laser phase noise is filtered in the correlation signal d...

  16. The generation of flat-top beams by complex amplitude modulation with a phase-only spatial light modulator

    CSIR Research Space (South Africa)

    Hendriks, A

    2012-08-01

    Full Text Available amplitude modulation of the light, i.e., in amplitude and phase. We outline the theoretical concept, and then illustrate its use with the example of the laser beam shaping of Gaussian beams into flat-top beams. We quantify the performance of this approach...

  17. PERFORMANCE ANALYSIS OF ORTHOGONAL FREQUENCY DIVISION MULTIPLEXING BASED BIDIRECTIONAL RELAY NETWORK IN THE PRESENCE OF PHASE NOISE

    Directory of Open Access Journals (Sweden)

    V. N. Senthil Kumaran

    2013-01-01

    Full Text Available In this study, the performance of OFDM based bidirectional relay network which employs Physical Layer Network Coding (PLNC is analyzed in the presence of phase noise. The bidirectional relay network is assumed to consist of two sources and a relay, where each node has a single antenna and operates in half duplex mode. The PLNC based OFDM system transmits high data streams over numerous sub channels in frequency domain. Each sub channel is a narrow band flat fading channel, thereby achieving high spectral efficiency over wide band channels. In practice, phase noise is introduced with the information symbols transmitted on all subcarriers in OFDM transceiver. The influence of phase noise on the received signals are analyzed at both the Multiple Access Channel (MAC and at the Broadcast Channel (BC environments.

  18. Multiplexed image storage by electromagnetically induced transparency in a solid

    Science.gov (United States)

    Heinze, G.; Rentzsch, N.; Halfmann, T.

    2012-11-01

    We report on frequency- and angle-multiplexed image storage by electromagnetically induced transparency (EIT) in a Pr3+:Y2SiO5 crystal. Frequency multiplexing by EIT relies on simultaneous storage of light pulses in atomic coherences, driven in different frequency ensembles of the inhomogeneously broadened solid medium. Angular multiplexing by EIT relies on phase matching of the driving laser beams, which permits simultaneous storage of light pulses propagating under different angles into the crystal. We apply the multiplexing techniques to increase the storage capacity of the EIT-driven optical memory, in particular to implement multiplexed storage of larger two-dimensional amounts of data (images). We demonstrate selective storage and readout of images by frequency-multiplexed EIT and angular-multiplexed EIT, as well as the potential to combine both multiplexing approaches towards further enhanced storage capacities.

  19. Direct UV written Michelson interferometer for RZ signal generation using phase-to-intensity modulation conversion

    DEFF Research Database (Denmark)

    Peucheret, Christophe; Geng, Yan; Zsigri, Beata

    2005-01-01

    An integrated Michelson delay interferometer structure making use of waveguide gratings as reflective elements is proposed and fabricated by direct ultraviolet writing. Successful return-to-zero alternate-mark-inversion signal generation using phase-to-intensity modulation conversion...

  20. Nonlinear Pulse Compression and Reshaping Using Cross-Phase Modulation in a Dispersion-Shifted Fiber

    Institute of Scientific and Technical Information of China (English)

    S.; W.; Chan; K.; K.; Chow; C.; Shu

    2003-01-01

    Nonlinear pulse compression has been demonstrated by cross-phase modulation in a dispersion-shifted fiber. The output is obtained from filtering of the broadened optical spectrum and a pulse width reduction from 61 to 28 ps is achieved.

  1. Sinusoidal Phase-Modulating Fabry-Perot Interferometer for Angular Displacement Measurement

    Institute of Scientific and Technical Information of China (English)

    Caini Zhang; Xiangzhao Wang

    2003-01-01

    In this paper, a sinusoidal phase-modulating Fabry-Perot interferometer is proposed to measure angular displacement.The usefulness of the interferometer is demonstrated by simulations and experiments.

  2. Sinusoidal Phase-Modulating Fabry-Perot Interferometer for Angular Displacement Measurement

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    In this paper, a sinusoidal phase-modulating Fabry-Perot interferometer is proposed to measure angular displacement. The usefulness of the interferometer is demonstrated by simulations and experiments.

  3. Evolution of sum-chirp in polarization multiplexed communication system

    Institute of Scientific and Technical Information of China (English)

    Wang Jing; Wang Zhen-Li

    2004-01-01

    The evolution of sum-chirp for an initially chirped Gaussian pulse is studied in the polarization multiplexed communication system, with fibre attenuation considered. The sum-chirp is found to have the character of saturation.Its value appears different along the two different polarization axes, determined by the incidence polarization angle. We also find that sum-chirp is dominated by the initial chirp at a short distance, and by the cross-phase modulation effect at long distance. And it is influenced apparently by a wavevector mismatch parameter below 10 ps/km. Further, its saturation results from the effective distance determined by fibre attenuation.

  4. Sinusoidal phase-modulating laser diode interferometer for real-time surface profile measurement

    Institute of Scientific and Technical Information of China (English)

    Guotian He; Xiangzhao Wang; Aijun Zeng; Feng Tang

    2007-01-01

    A sinusoidal phase-modulating (SPM) laser diode (LD) interferometer for real-time surface profile measurement is proposed and its principle is analyzed. The phase signal of the surface profile is detected from the sinusoidal phase-modulating interference signal using a real-time phase detection circuit. For 60 × 60 measurement points of the surface profile, the measuring time is 10 ms. A root mean square (RMS) measurement repeatability of 3.93 nm is realized, and the measurement resolution reaches 0.19 nm.

  5. Heterodyne technique for measuring the amplitude and phase transfer functions of an optical modulator

    DEFF Research Database (Denmark)

    Romstad, Francis Pascal; Birkedal, Dan; Mørk, Jesper

    2002-01-01

    In this letter, we propose a technique based on heterodyne detection for accurately and simultaneously measuring the amplitude and phase transfer functions of an optical modulator. The technique is used to characterize an InGaAsp multiple quantum-well electroabsorption modulator. From...

  6. Photoassociation dynamics driven by second- and third-order phase-modulated laser fields

    Science.gov (United States)

    Wang, Meng; Chen, Mao-Du; Hu, Xue-Jin; Li, Jing-Lun; Cong, Shu-Lin

    2016-05-01

    We investigate theoretically the photoassociation dynamics of ultracold 85Rb atoms driven by second- and third-order phase-modulated laser fields. The interplay between the second-order and third-order terms of the phase-modulated pulse has an obvious influence on photoassociation dynamics. The different combinations of the second-order and third-order phase coefficients lead to different pulse shapes. Most of the molecular population in the excited electronic state driven only by the third-order phase pulses can be distributed in a single vibrational level. The second-order term of the phase-modulated pulse can change the instantaneous frequency, and therefore the final population is distributed on several resonant vibrational levels, instead of concentrating on a single level. Although the second- and third-order phase-modulated pulse covers more resonant vibrational levels, the total population on the resonant vibrational levels is much smaller than that controlled only by the third-order phase pulse. In particular, the third-order term of the phase-modulated pulse can weaken the ‘multiple interaction’ to some degree.

  7. Multi-wavelength integrated optical beamformer based on Wavelength division multiplexing for 2-D phased array antennas

    NARCIS (Netherlands)

    Burla, Maurizio; Marpaung, David; Zhuang, Leimeng; Khan, Muhannad Rezaul; Leinse, Arne; Beeker, Willem; Hoekman, Marcel; Heideman, René; Roeloffzen, Chris

    2014-01-01

    A novel, hardware-compressive architecture for broadband and continuously tunable integrated optical truetime- delay beamformers for phased array antennas is proposed and experimentally demonstrated. The novel idea consists in employing the frequency-periodic response of optical ring resonator (ORR)

  8. Phase Modulation for postcompensation of dispersion in 160-Gb/s systems

    DEFF Research Database (Denmark)

    Siahlo, Andrei; Clausen, A. T.; Oxenløwe, Leif Katsuo

    2005-01-01

    Tunable postcompensation of second-order dispersion by sinusoidal phase modulation is realized for a 160-Gb/s optical transmission system. Accumulated dispersions with magnitudes up to 4 ps/nm are compensated in the receiver end.......Tunable postcompensation of second-order dispersion by sinusoidal phase modulation is realized for a 160-Gb/s optical transmission system. Accumulated dispersions with magnitudes up to 4 ps/nm are compensated in the receiver end....

  9. Spectral Compression of Intense Femtosecond Pulses by Self Phase Modulation in Silica Glass

    DEFF Research Database (Denmark)

    Iwaszczuk, Krzysztof; Zhou, Binbin; Bache, Morten

    2012-01-01

    We experimentally demonstrate spectral compression of mJ fs pulses by self phase modulation in silica glass. Spectral narrowing by factor 2.4 of near-transform-limited pulses is shown, with good agreement between experiment and numerical simulation.......We experimentally demonstrate spectral compression of mJ fs pulses by self phase modulation in silica glass. Spectral narrowing by factor 2.4 of near-transform-limited pulses is shown, with good agreement between experiment and numerical simulation....

  10. Distributed MIMO Antenna Architecture for Wireless-over- Fiber Backhaul with Multicarrier Optical Phase Modulation

    DEFF Research Database (Denmark)

    Caballero Jambrina, Antonio; Wong, Shing-Wa; Zibar, Darko

    2011-01-01

    A novel optical phase-modulated wireless-over-fiber backhaul architecture for next generation cellular network is presented and experimentally demonstrated for high capacity wireless multicarrier uplink transmission on a single wavelength.......A novel optical phase-modulated wireless-over-fiber backhaul architecture for next generation cellular network is presented and experimentally demonstrated for high capacity wireless multicarrier uplink transmission on a single wavelength....

  11. Phase modulation spectroscopy of space-charge wave resonances in Bi12SiO20

    DEFF Research Database (Denmark)

    Vasnetsov, M.; Buchhave, Preben; Lyuksyutov, S.

    1997-01-01

    A new experimental method for the study of resonance effects and space-charge wave excitation in photorefractive Bi12SiO20 crystals by using a combination of frequency detuning and phase modulation technique has been developed. The accuracy of the method allows a detection of resonance peaks...... and revealed its resonance dependence. A minimum of electric current through the sample corresponds to the main resonance detected by phase modulation technique....

  12. Asymmetrically pumped Bragg scattering with the effects of nonlinear phase modulation

    DEFF Research Database (Denmark)

    Andersen, Lasse Mejling; Friis, Søren Michael Mørk; Reddy, Dileep V.

    2014-01-01

    We derive exact solutions to asymmetrically pumped Bragg scattering with nonlinear phase-modulation (NPM) and show that this setup allows for the frequency conversion of many temporal modes, while reducing the effects due to NPM.......We derive exact solutions to asymmetrically pumped Bragg scattering with nonlinear phase-modulation (NPM) and show that this setup allows for the frequency conversion of many temporal modes, while reducing the effects due to NPM....

  13. Surface phase defects induced downstream laser intensity modulation in high-power laser facility

    Institute of Scientific and Technical Information of China (English)

    Xin Zhang; Wei Zhou; Wanjun Dai; Dongxia Hu; Xuewei Deng; Wanqing Huang; Lidan Zhou; Qiang Yuan; Xiaoxia Huang; De’en Wang; Ying Yang

    2016-01-01

    Optics surface phase defects induced intensity modulation in high-power laser facility for inertial confinement fusion research is studied. Calculations and experiments reveal an exact mapping of the modulation patterns and the optics damage spot distributions from the surface phase defects. Origins are discussed during the processes of optics manufacturing and diagnostics, revealing potential improvements for future optics manufacturing techniques and diagnostic index, which is meaningful for fusion level laser facility construction and its operation safety.

  14. Experimental Demonstration of Capacity-Achieving Phase-Shifted Superposition Modulation

    DEFF Research Database (Denmark)

    Estaran Tolosa, Jose Manuel; Zibar, Darko; Caballero Jambrina, Antonio

    2013-01-01

    We report on the first experimental demonstration of phase-shifted superposition modulation (PSM) for optical links. Successful demodulation and decoding is obtained after 240 km transmission for 16-, 32- and 64-PSM.......We report on the first experimental demonstration of phase-shifted superposition modulation (PSM) for optical links. Successful demodulation and decoding is obtained after 240 km transmission for 16-, 32- and 64-PSM....

  15. On The Use of A Phase Modulation Method for Decorrelation in Acoustic Feedback Cancellation

    DEFF Research Database (Denmark)

    Guo, Meng; Jensen, Søren Holdt; Jensen, Jesper

    2012-01-01

    of decorrelation. In this work, we study a subband phase modulation method, which was originally proposed for decorrelation in multichannel acoustic echo cancellation systems. We determine if this method is effective for decorrelation in acoustic feedback cancellation systems by comparing it to a structurally...... similar frequency shifting decorrelation method. We show that the phase modulation method is suitable for decorrelation in a hearing aid acoustic feedback cancellation system, although the frequency shifting method is in general slightly more effective....

  16. Brillouin suppression in a fiber optical parametric amplifier by combining temperature distribution and phase modulation

    DEFF Research Database (Denmark)

    Lorenzen, Michael Rodas; Noordegraaf, Danny; Nielsen, Carsten Vandel

    2008-01-01

    We demonstrate an increased gain in optical parametric amplier through suppression of stimulated Brillouin scattering by applying a temperature distribution along the fiber resulting in a reduction of the required phase modulation.......We demonstrate an increased gain in optical parametric amplier through suppression of stimulated Brillouin scattering by applying a temperature distribution along the fiber resulting in a reduction of the required phase modulation....

  17. Wideband phase-locked loop circuit with real-time phase correction for frequency modulation atomic force microscopy

    OpenAIRE

    Fukuma, Takeshi; Yoshioka, Shunsuke; Asakawa, Hitoshi

    2011-01-01

    We have developed a wideband phase-locked loop (PLL) circuit with real-time phase correction for high-speed and accurate force measurements by frequency modulation atomic force microscopy (FM-AFM) in liquid. A high-speed operation of FM-AFM requires the use of a high frequency cantilever which, however, increases frequency-dependent phase delay caused by the signal delay within the cantilever excitation loop. Such phase delay leads to an error in the force measurements by FM-AFM especially wi...

  18. 10 Gbps Colorless Optical Source in Wavelength-Division Multiplexed Passive Optical Networks for Monolithic Integration of Deep-Ridge Waveguide Electroabsorption Modulator with Planar Buried-Heterostructure Semiconductor Optical Amplifier

    Science.gov (United States)

    Kim, Dong Churl; Kim, Ki Soo; Kim, Hyun-Soo; Choi, Byung-Seok; Kwon, O.-Kyun

    2012-05-01

    For the 10 Gbps colorless optical source in wavelength-division multiplexed passive optical networks (WDM-PONs), we have fabricated a semiconductor optical amplifier-reflective electorabsorption modulator (SOA-REAM) by monolithic integration of deep-ridge waveguide REAM (DRW-REAM) with planar buried-heterostructure (PBH) SOA using a PNP-current blocking layer. The SOA-REAM has a spot-size convertor for easy fiber coupling. Using a butterfly module with an SMA connector, we have packaged the SOA-REAM. At a -10 dBm input power of 1550 nm, the saturation output power is about 6 dBm. At 10.7 Gbps, we can obtain clear eye diagrams, and the power penalty at 10-9 bit-error rate (BER) after 20 km transmission is less than 1 dB over 35 nm.

  19. A phase-locked laser system based on modulation technique for atom interferometry

    CERN Document Server

    Li, Wei; Song, Ningfang; Xu, Xiaobin; Lu, Xiangxiang

    2016-01-01

    We demonstrate a Raman laser system based on phase modulation technology and phase feedback control. The two laser beams with frequency difference of 6.835 GHz are modulated using electro-optic and acousto-optic modulators, respectively. Parasitic frequency components produced by the electro-optic modulator are filtered using a Fabry-Perot Etalon. A straightforward phase feedback system restrains the phase noise induced by environmental perturbations. The phase noise of the laser system stays below -125 rad2/Hz at frequency offset higher than 500 kHz. Overall phase noise of the laser system is evaluated by calculating the contribution of the phase noise to the sensitivity limit of a gravimeter. The results reveal that the sensitivity limited by the phase noise of our laser system is lower than that of a state-of-art optical phase-lock loop scheme when a gravimeter operates at short pulse duration, which makes the laser system a promising option for our future application of atom interferometer.

  20. A phase-locked laser system based on double direct modulation technique for atom interferometry

    Science.gov (United States)

    Li, Wei; Pan, Xiong; Song, Ningfang; Xu, Xiaobin; Lu, Xiangxiang

    2017-02-01

    We demonstrate a laser system based on phase modulation technology and phase feedback control. The two laser beams with frequency difference of 6.835 GHz are modulated using electro-optic and acousto-optic modulators, respectively. Parasitic frequency components produced by the electro-optic modulator are filtered using a Fabry-Perot Etalon. A straightforward phase feedback system restrains the phase noise induced by environmental perturbations. The phase noise of the laser system stays below -125 rad2/Hz at frequency offset higher than 500 kHz. Overall phase noise of the laser system is evaluated by calculating the contribution of the phase noise to the sensitivity limit of a gravimeter. The results reveal that the sensitivity limited by the phase noise of our laser system is lower than that of a state-of-the-art optical phase-lock loop scheme when a gravimeter operates at short pulse duration, which makes the laser system a promising option for our future application of atom interferometer.

  1. Novel electro-optical phase modulator based on GaInAs/InP modulation-doped quantum-well structures

    DEFF Research Database (Denmark)

    Thirstrup, C.

    1992-01-01

    A novel electro-optical phase modulator working at 1.55 µm is analyzed and proposed. It is shown by a numerical model that in a GaInAs/InP pn-nin-pn multiple-quantum-well waveguide structure, large optical phase modulation can be obtained at small intensity modulation and with improved performance...... compared to what is achieved in quantum confined Stark effect modulators of the same material system. The device proposed is based on a modulation of the quasi-Fermi energies of the electrons in the GaInAs quantum wells. This operational principle allows GHz modulation frequencies. Applied Physics Letters...

  2. Hidden phase in a two-dimensional Sn layer stabilized by modulation hole doping

    Science.gov (United States)

    Ming, Fangfei; Mulugeta, Daniel; Tu, Weisong; Smith, Tyler S.; Vilmercati, Paolo; Lee, Geunseop; Huang, Ying-Tzu; Diehl, Renee D.; Snijders, Paul C.; Weitering, Hanno H.

    2017-03-01

    Semiconductor surfaces and ultrathin interfaces exhibit an interesting variety of two-dimensional quantum matter phases, such as charge density waves, spin density waves and superconducting condensates. Yet, the electronic properties of these broken symmetry phases are extremely difficult to control due to the inherent difficulty of doping a strictly two-dimensional material without introducing chemical disorder. Here we successfully exploit a modulation doping scheme to uncover, in conjunction with a scanning tunnelling microscope tip-assist, a hidden equilibrium phase in a hole-doped bilayer of Sn on Si(111). This new phase is intrinsically phase separated into insulating domains with polar and nonpolar symmetries. Its formation involves a spontaneous symmetry breaking process that appears to be electronically driven, notwithstanding the lack of metallicity in this system. This modulation doping approach allows access to novel phases of matter, promising new avenues for exploring competing quantum matter phases on a silicon platform.

  3. Design-oriented analytic model of phase and frequency modulated optical links

    Science.gov (United States)

    Monsurrò, Pietro; Saitto, Antonio; Tommasino, Pasquale; Trifiletti, Alessandro; Vannucci, Antonello; Cimmino, Rosario F.

    2016-07-01

    An analytic design-oriented model of phase and frequency modulated microwave optical links has been developed. The models are suitable for design of broadband high dynamic range optical links for antenna remoting and optical beamforming, where noise and linearity of the subsystems are a concern Digital filter design techniques have been applied to the design of optical filters working as frequency discriminator, that are the bottleneck in terms of linearity for these systems. The models of frequency modulated, phase modulated, and coherent I/Q link have been used to compare performance of the different architectures in terms of linearity and SFDR.

  4. Acoustically modulated x-ray phase contrast imaging.

    Science.gov (United States)

    Hamilton, Theron J; Bailat, Claude J; Rose-Petruck, Christoph; Diebold, Gerald J

    2004-11-07

    We report the use of ultrasonic radiation pressure with phase contrast x-ray imaging to give an image proportional to the space derivative of a conventional phase contrast image in the direction of propagation of an ultrasonic beam. Intense ultrasound is used to exert forces on objects within a body giving displacements of the order of tens to hundreds of microns. Subtraction of images made with and without the ultrasound field gives an image that removes low spatial frequency features and highlights high frequency features. The method acts as an acoustic 'contrast agent' for phase contrast x-ray imaging, which in soft tissue acts to highlight small density changes.

  5. Synthesis of dynamic phase profile by the correlation technique for spatial control of optical beams in multiplexing and switching

    Science.gov (United States)

    Bugaychuk, Svitlana A.; Gnatovskyy, Vladimir O.; Sidorenko, Andrey V.; Pryadko, Igor I.; Negriyko, Anatoliy M.

    2015-11-01

    New approach for the correlation technique, which is based on multiple periodic structures to create a controllable angular spectrum, is proposed and investigated both theoretically and experimentally. The transformation of an initial laser beam occurs due to the actions of consecutive phase periodic structures, which may differ by their parameters. Then, after the Fourier transformation of a complex diffraction field, the output diffraction orders will be changed both by their intensities and by their spatial position. The controllable change of output angular spectrum is carried out by a simple control of the parameters of the periodic structures. We investigate several simple examples of such management.

  6. Transparent building-integrated PV modules. Phase 1: Comprehensive report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-09-28

    This Comprehensive Report encompasses the activities that have been undertaken by Kiss + Cathcart, Architects, in conjunction with Energy Photovoltaics, Incorporated (EPV), to develop a flexible patterning system for thin-film photovoltaic (PV) modules for building applications. There are two basic methods for increasing transparency/light transmission by means of patterning the PV film: widening existing scribe lines, or scribing a second series of lines perpendicular to the first. These methods can yield essentially any degree of light transmission, but both result in visible patterns of light and dark on the panel surface. A third proposed method is to burn a grid of dots through the films, independent of the normal cell scribing. This method has the potential to produce a light-transmitting panel with no visible pattern. Ornamental patterns at larger scales can be created using combinations of these techniques. Kiss + Cathcart, Architects, in conjunction with EPV are currently developing a complementary process for the large-scale lamination of thin-film PVs, which enables building integrated (BIPV) modules to be produced in sizes up to 48 in. x 96 in. Flexible laser patterning will be used for three main purposes, all intended to broaden the appeal of the product to the building sector: To create semitransparent thin-film modules for skylights, and in some applications, for vision glazing.; to create patterns for ornamental effects. This application is similar to fritted glass, which is used for shading, visual screening, graphics, and other purposes; and to allow BIPV modules to be fabricated in various sizes and shapes with maximum control over electrical characteristics.

  7. Soliton Formation in Whispering-Gallery-Mode Resonators via Input Phase Modulation

    CERN Document Server

    Taheri, Hossein; Wiesenfeld, Kurt; Adibi, Ali

    2014-01-01

    We propose a method for soliton formation in whispering-gallery-mode (WGM) resonators through input phase modulation. Our numerical simulations of a variant of the Lugiato-Lefever equation suggest that modulating the input phase at a frequency equal to the resonator free-spectral-range and at modest modulation depths provides a deterministic route towards soliton formation in WGM resonators without undergoing a chaotic phase. We show that the generated solitonic state is sustained when the modulation is turned off adiabatically. Our results support parametric seeding as a powerful means of control, besides input pump power and pump-resonance detuning, over frequency comb generation in WGM resonators. Our findings also help pave the path towards ultra-short pulse formation on a chip.

  8. DUAL THREE-PHASE ADJUSTABLE SPEED DRIVE WITH SYNCHRONIZED SPACE-VECTOR MODULATION

    Directory of Open Access Journals (Sweden)

    Oleschuk V.I.

    2008-04-01

    Full Text Available Split-phase symmetrical motor drive on the base of two voltage source inverters, controlled by algorithms of synchronized pulse width modulation (PWM, has been investigated. Simulation results are presented for dual three-phase power conversion systems with continuous, discontinuous and combined versions of synchronized PWM.

  9. Multipacket Reception in Wireless Ad Hoc Networks Based on CDMA and Polynomial Phase-modulating Sequences

    Institute of Scientific and Technical Information of China (English)

    ZHANG Ji-dong; Wang Bao-yun; ZHENG Bao-yu

    2004-01-01

    Based on the polynomial phase-modulating sequences algorithm, this paper presents two schemes for the application of CDMA with polynomial phase signals to improve the signal separation performance. Simulation results illustrate the proposed approach have 1~3 dB improvement about signal-to-interference and noise ratio in most environment, compared with the PPS algorithm.

  10. Integrated quasi-phase-matched second-harmonic generator and electro-optic phase modulator for low-noise phase-sensitive amplification.

    Science.gov (United States)

    Enbutsu, Koji; Umeki, Takeshi; Tadanaga, Osamu; Asobe, Masaki; Takenouchi, Hirokazu

    2015-07-15

    We propose a quasi-phase-matched second-harmonic generator integrated with an electro-optic phase modulator in a directly bonded LiNbO3 (DB-LN) waveguide to obtain high signal-to-noise ratio (SNR) pump light for a phase-sensitive amplifier (PSA). This integrated device exhibits 1-MHz modulation and 1-W second-harmonic-generation properties sufficient for phase-locking between the signal and pump and for PSA gain, respectively. A novel PSA configuration based on the high-input-power tolerance of the device helps to suppress the noise from the erbium-doped fiber amplifier used for pump-light generation and leads to an improvement of the SNR of the pump light. The SNR improvement was confirmed by comparing the noise figure of a PSA employing the DB-LN waveguide with that of a PSA using a Ti-diffused LN waveguide modulator.

  11. Wideband phase-locked loop circuit with real-time phase correction for frequency modulation atomic force microscopy

    Science.gov (United States)

    Fukuma, Takeshi; Yoshioka, Shunsuke; Asakawa, Hitoshi

    2011-07-01

    We have developed a wideband phase-locked loop (PLL) circuit with real-time phase correction for high-speed and accurate force measurements by frequency modulation atomic force microscopy (FM-AFM) in liquid. A high-speed operation of FM-AFM requires the use of a high frequency cantilever which, however, increases frequency-dependent phase delay caused by the signal delay within the cantilever excitation loop. Such phase delay leads to an error in the force measurements by FM-AFM especially with a low Q factor. Here, we present a method to compensate this phase delay in real time. Combined with a wideband PLL using a subtraction-based phase comparator, the method allows to perform an accurate and high-speed force measurement by FM-AFM. We demonstrate the improved performance by applying the developed PLL to three-dimensional force measurements at a mica/water interface.

  12. Intrachannel cross-phase modulation-induced phase shift in high-speed dispersion-managed optical fiber transmission system

    Science.gov (United States)

    Syed, Nitu; Faisal, Mohammad

    2013-12-01

    We investigate the intrachannel cross-phase modulation (IXPM)-induced phase shift in optical return-to-zero pulse propagating in a periodically dispersion-managed long-haul optical fiber transmission line. Necessary dynamical equations for various pulse parameters have been derived using variational analysis to estimate the phase shift. These equations are solved by the Runge-Kutta method. The analytical result is verified by numerical simulation based on split-step Fourier method. We therefore explore the effects of various parameters, such as transmission distance, input power, duty cycle, dispersion map strength, and residual dispersion, on phase shift for a 40 Gb/s single-channel transmission system. We also check the impact of variation of bit rate on phase shift. We find that IXPM-induced phase shift can be mitigated by proper adjustment of dispersion management and different pulse parameters like duty cycle, dispersion map strength, and peak power.

  13. Remarks on nonlinear relation among phases and frequencies in modulational instabilities of parallel propagating Alfven waves

    CERN Document Server

    Nariyuki, Y; Nariyuki, Yasuhiro; Hada, Tohru

    2006-01-01

    Nonlinear relations among frequencies and phases in modulational instability of circularly polarized Alfven waves are discussed, within the context of one dimensional, dissipation-less, unforced fluid system. We show that generation of phase coherence is a natural consequence of the modulational instability of Alfven waves. Furthermore, we quantitatively evaluate intensity of wave-wave interaction by using bi-coherence, and also by computing energy flow among wave modes, and demonstrate that the energy flow is directly related to the phase coherence generation.

  14. Coherent storage and phase modulation of single hard-x-ray photons using nuclear excitons.

    Science.gov (United States)

    Liao, Wen-Te; Pálffy, Adriana; Keitel, Christoph H

    2012-11-09

    The coherent storage and phase modulation of x-ray single-photon wave packets in the resonant scattering of light off nuclei is theoretically investigated. We show that by switching off and on again the magnetic field in the nuclear sample, phase-sensitive storage of photons in the keV regime can be achieved. Corresponding π phase modulation of the stored photon can be accomplished if the retrieving magnetic field is rotated by 180°. The development of such x-ray single-photon control techniques is a first step towards forwarding quantum optics and quantum information to shorter wavelengths and more compact photonic devices.

  15. Phase modulation parallel optical delay detector for microwave angle-of-arrival measurement with accuracy monitored

    CERN Document Server

    Cao, Z; Lu, R; Boom, H P A van den; Tangdiongga, E; Koonen, A M J

    2014-01-01

    A novel phase modulation parallel optical delay detector is proposed for microwave angle-of-arrival (AOA) measurement with accuracy monitored by using only one dual-electrode Mach-Zenhder modulator. A theoretical model is built up to analyze the proposed system including measurement accuracy monitoring. The spatial delay measurement is translated into the phase shift between two replicas of a microwave signal. Thanks to the accuracy monitoring, the phase shifts from 5{\\deg} to 165{\\deg} are measured with less than 3.1{\\deg} measurement error.

  16. Time-division phase modulated single-photon interference in a Sagnac interferometer

    Institute of Scientific and Technical Information of China (English)

    WU Guang; ZHOU Chunyuan; ZENG Heping

    2003-01-01

    We introduce a stable, long-distance single- photon Sagnac interferometer, which has a balanced configuration to efficiently compensate phase drift caused by change of the fiber-optic path. By using time-division phase modulation, single-photon interference was realized at 1550 nm in a 5-km-long as well as 27-km-long Sagnac fiber loops, with a fringe visibility higher than 90% and long-term stability. The stable performance of the single-photon interference indicated that the time-division phase-modulated Sag- nac interferometer might readily lead to practical applications in single-photon routing and quantum cryptography.

  17. Modulation Schemes of Multi-phase Three-Level Z-Source Inverters

    DEFF Research Database (Denmark)

    Gao, F.; Loh, P.C.; Blaabjerg, Frede;

    2007-01-01

    This paper investigates the modulation schemes of three-level multiphase Z-source inverters with either two Z-source networks or single Z-source network connected between the dc sources and inverter circuitry. With the proper offset added for achieving both desired four-leg operation and optimized...... harmonic performance, the proposed modulation schemes of four-leg three-level Z-source inverters can satisfy the expected buck-boost operation under unbalanced modulation conditions. Except of the modulation complexity hidden in the four-leg inverters, five-phase three-level Z-source inverters show totally...... different modulation requirement and output performance. For clearly illustrating the detailed modulation process, time domain analysis instead of the traditional multi-dimensional space vector demonstration is assumed which reveals the right way to insert shoot-through durations in the switching sequence...

  18. Pattern manipulation via on-chip phase modulation between orbital angular momentum beams

    Energy Technology Data Exchange (ETDEWEB)

    Li, Huanlu [Department of Electrical and Electronic Engineering, University of Bristol, University Walk, Bristol BS8 1TR (United Kingdom); School of Engineering, University of Glasgow, Rankine Building, Oakfield Avenue, Glasgow G12 8LP (United Kingdom); Strain, Michael J. [School of Engineering, University of Glasgow, Rankine Building, Oakfield Avenue, Glasgow G12 8LP (United Kingdom); Wolfson Centre, Institute of Photonics, University of Strathclyde, 106 Rottenrow East, Glasgow G4 0NW (United Kingdom); Meriggi, Laura; Sorel, Marc [School of Engineering, University of Glasgow, Rankine Building, Oakfield Avenue, Glasgow G12 8LP (United Kingdom); Chen, Lifeng; Zhu, Jiangbo; Cicek, Kenan [Department of Electrical and Electronic Engineering, University of Bristol, University Walk, Bristol BS8 1TR (United Kingdom); Wang, Jianwei; Thompson, Mark G. [Centre for Quantum Photonics, H. H. Wills Physics Laboratory and Department of Electrical and Electronic Engineering, University of Bristol, Bristol BS8 1UB (United Kingdom); Cai, Xinlun, E-mail: caixlun5@mail.sysu.edu.cn [Centre for Quantum Photonics, H. H. Wills Physics Laboratory and Department of Electrical and Electronic Engineering, University of Bristol, Bristol BS8 1UB (United Kingdom); State Key Laboratory of Optoelectronic Materials and Technologies and School of Physics and Engineering, Sun Yat-sen University, Guangzhou 510275 (China); Yu, Siyuan, E-mail: s.yu@bristol.ac.uk [Department of Electrical and Electronic Engineering, University of Bristol, University Walk, Bristol BS8 1TR (United Kingdom); State Key Laboratory of Optoelectronic Materials and Technologies and School of Physics and Engineering, Sun Yat-sen University, Guangzhou 510275 (China)

    2015-08-03

    An integrated approach to thermal modulation of relative phase between two optical vortices with opposite chirality has been demonstrated on a silicon-on-insulator substrate. The device consists of a silicon-integrated optical vortex emitter and a phase controlled 3 dB coupler. The relative phase between two optical vortices can be actively modulated on chip by applying a voltage on the integrated heater. The phase shift is shown to be linearly proportional to applied electrical power, and the rotation angle of the interference pattern is observed to be inversely proportional to topological charge. This scheme can be used in lab-on-chip, communications and sensing applications. It can be intentionally implemented with other modulation elements to achieve more complicated applications.

  19. Effect of Phase Shifted Frequency Modulation on Two Level Atom-Field Interaction

    Institute of Scientific and Technical Information of China (English)

    K.V. Priyesh; Ramesh Babu Thayyullathil

    2012-01-01

    We have studied the effect of phase shifted frequency modulation on two level atom with field interaction using Jaynes-Cummings model. Here the frequency of the interacting field is sinusoidally varying with time with a constant phase. Due to the presence of phase in the frequency modulation, the variation of population inversion with time is different from the standard case. There are no exact collapses and revivals in the variation of population inversion but it oscillates sinusoidally with time. In coherent field atom interaction the population inversion behaves as in the case of Fock state atom interaction, when frequency modulation with a non zero phase is applied. The study done with squeezed field has shown the same behavior of the population inversion.

  20. Optical phase modulator utilizing a transparent piezofilm for use with the extrinsic fiber interferometer

    Science.gov (United States)

    Sudarshanam, V. S.; Claus, Richard O.

    1993-03-01

    A piezoelectnc polyvinylidene flouride (PVF2) film with transparent indium tin oxide electrode metallization is placed directly in the path of a single mode fiber output, to form an extrinsic optical interferometer. This device can be used concurrently with another extrinsic inteferometer on a fiber directional coupler to generate a carrier phase modulation on which the signal phase shift is superimposed. Experimental results of the induced phase shifting coefficient are presented for two arrangements of the piezofilm differing in their boundary clamping conditions.

  1. Polarization multiplexed dual-loop optoelectronic oscillator based on stimulated Brillouin scattering

    Science.gov (United States)

    Han, Xiuyou; Ma, Liang; Shao, Yuchen; Ye, Qing; Gu, Yiying; Zhao, Mingshan

    2017-01-01

    A polarization multiplexed dual-loop optoelectronic oscillator (OEO) based on stimulated Brillouin scattering (SBS) is theoretically analyzed and experimentally demonstrated. The narrow bandwidth of SBS gain spectrum is utilized to implement the phase modulation to intensity modulation conversion and select the oscillation mode of the OEO. The polarization multiplexed dual-loop is constructed to suppress the side modes with Vernier effect. The output frequency of the OEO can be tuned by changing the frequency of the signal or the pump light wave. With the polarization multiplexed dual-loop the side-mode suppression ratio (SMSR) of 45 dB is achieved at 10 GHz. The generated oscillation frequency is tuned from 4 GHz to 16 GHz by changing the frequency of the signal light wave. The phase noise decreases with the power increase of the signal light wave when it is under the threshold of SBS. By adjusting the polarization state of the light wave, the influence of the power distribution between the long loop and the short loop on the phase noise of the OEO is investigated. The results show that more power in the long loop is helpful to suppress the near end phase noise.

  2. Sample-specific conductance fluctuations modulated by the superconducting phase

    NARCIS (Netherlands)

    den Hartog, SG; Kapteyn, CMA; van Wees, BJ; Klapwijk, TM; Borghs, G

    1998-01-01

    We present an overview of sample-specific transport properties tuned by the superconducting phase difference between two superconductors connected to a disordered 2-dimensional electron gas (2DEG). We demonstrate a crossover from ensemble-averaged to sample-specific resistance oscillations of a T-sh

  3. Characteristics of phase-averaged equations for modulated wave groups

    NARCIS (Netherlands)

    Klopman, G.; Petit, H.A.H.; Battjes, J.A.

    2000-01-01

    The project concerns the influence of long waves on coastal morphology. The modelling of the combined motion of the long waves and short waves in the horizontal plane is done by phase-averaging over the short wave motion and using intra-wave modelling for the long waves, see e.g. Roelvink (1993). Th

  4. FPGA-based phase control of acousto-optic modulator Fourier synthesis system through gradient descent phase-locking algorithm.

    Science.gov (United States)

    Underwood, Kenneth J; Jones, Andrew M; Gopinath, Juliet T

    2015-06-20

    We present a new application of the stochastic parallel gradient descent (SPGD) algorithm to fast active phase control in a Fourier synthesis system. Pulses (4.9 ns) with an 80 MHz repetition rate are generated by feedback from a single phase-sensitive metric. Phase control is applied via fast current modulation of a tapered amplifier using an SPGD algorithm realized on a field-programmable gate array (FPGA). The waveforms are maintained by constant active feedback from the FPGA. We also discuss the extension of this technique to many more semiconductor laser emitters in a diode laser array.

  5. Nonlinear phase shifts of modulated light waves with slow and superluminal group delay in stimulated Brillouin scattering.

    Science.gov (United States)

    Arditi, Tal; Granot, Er'el; Sternklar, Shmuel

    2007-09-15

    Brillouin amplification with counterpropagating modulated pump and Stokes light leads to nonlinear modulation-phase shifts of the interacting intensity waves. This is due to a partial transformation of the nonmodulated light component at the input into modulated light at the output as a result of a mixing process with the counterpropagating modulated component of the pump and results in an advance or delay of the input modulation. This occurs for interactions over less than half of a modulation wavelength. Milliwatts of power in a kilometer of standard single-mode fiber give significant tunability of the modulation phase.

  6. Paper-based solid-phase multiplexed nucleic acid hybridization assay with tunable dynamic range using immobilized quantum dots as donors in fluorescence resonance energy transfer.

    Science.gov (United States)

    Noor, M Omair; Krull, Ulrich J

    2013-08-06

    A multiplexed solid-phase nucleic acid hybridization assay on a paper-based platform is presented using multicolor immobilized quantum dots (QDs) as donors in fluorescence resonance energy transfer (FRET). The surface of paper was modified with imidazole groups to immobilize two types of QD-probe oligonucleotide conjugates that were assembled in solution. Green-emitting QDs (gQDs) and red-emitting QDs (rQDs) served as donors with Cy3 and Alexa Fluor 647 (A647) acceptors. The gQD/Cy3 FRET pair served as an internal standard, while the rQD/A647 FRET pair served as a detection channel, combining the control and analytical test zones in one physical location. Hybridization of dye-labeled oligonucleotide targets provided the proximity for FRET sensitized emission from the acceptor dyes, which served as an analytical signal. Hybridization assays in the multicolor format provided a limit of detection of 90 fmol and an upper limit of dynamic range of 3.5 pmol. The use of an array of detection zones was designed to provide improved analytical figures of merit compared to that which could be achieved on one type of array design in terms of relative concentration of multicolor QDs. The hybridization assays showed excellent resistance to nonspecific adsorption of oligonucleotides. Selectivity of the two-plex hybridization assay was demonstrated by single nucleotide polymorphism (SNP) detection at a contrast ratio of 50:1. Additionally, it is shown that the use of preformed QD-probe oligonucleotide conjugates and consideration of the relative number density of the two types of QD-probe conjugates in the two-color assay format is advantageous to maximize assay sensitivity and the upper limit of dynamic range.

  7. Fuzzy Logic Controlled Solar Module for Driving Three- Phase Induction Motor

    Science.gov (United States)

    Afiqah Zainal, Nurul; Sooi Tat, Chan; Ajisman

    2016-02-01

    Renewable energy produced by solar module gives advantages for generated three- phase induction motor in remote area. But, solar module's ou tput is uncertain and complex. Fuzzy logic controller is one of controllers that can handle non-linear system and maximum power of solar module. Fuzzy logic controller used for Maximum Power Point Tracking (MPPT) technique to control Pulse-Width Modulation (PWM) for switching power electronics circuit. DC-DC boost converter used to boost up photovoltaic voltage to desired output and supply voltage source inverter which controlled by three-phase PWM generated by microcontroller. IGBT switched Voltage source inverter (VSI) produced alternating current (AC) voltage from direct current (DC) source to control speed of three-phase induction motor from boost converter output. Results showed that, the output power of solar module is optimized and controlled by using fuzzy logic controller. Besides that, the three-phase induction motor can be drive and control using VSI switching by the PWM signal generated by the fuzzy logic controller. This concluded that the non-linear system can be controlled and used in driving three-phase induction motor.

  8. Large resistivity modulation in mixed-phase metallic systems

    Science.gov (United States)

    Lee, Yeonbae; Liu, Zhiqi; Heron, John; Clarkson, James; Hong, Jeongmin; Ko, Changhyun; Biegalski, Michael; Aschauer, Ulrich; Hsu, Shang-Lin; Nowakowski, Mark; Wu, Junqiao; Christen, Hans; Salahuddin, Sayeef; Bokor, Jeffrey; Spaldin, Nicola; Schlom, Darrell; Ramesh, Ramamoorthy

    2015-03-01

    We have investigated the effect of an electric field to FeRh/PMN-PT heterostructures and report 8% change in the electrical resistivity of FeRh films. Such a ``giant'' electroresistance (GER) response is striking in metallic systems, in which external electric fields are screened and thus only weakly influence the carrier concentrations and mobilities. We show that our FeRh films comprise coexisting ferromagnetic and antiferromagnetic phases with different resistivities, and the origin of the GER effect is the strain-mediated change in their relative proportions. The observed behavior is reminiscent of colossal magnetoresistance in perovskite manganites, and illustrates the role of mixed-phase coexistence in achieving large changes in physical properties with low-energy external perturbation.

  9. Network based management for multiplexed electric vehicle charging

    Energy Technology Data Exchange (ETDEWEB)

    Gadh, Rajit; Chung, Ching Yen; Qui, Li

    2017-04-11

    A system for multiplexing charging of electric vehicles, comprising a server coupled to a plurality of charging control modules over a network. Each of said charging modules being connected to a voltage source such that each charging control module is configured to regulate distribution of voltage from the voltage source to an electric vehicle coupled to the charging control module. Data collection and control software is provided on the server for identifying a plurality of electric vehicles coupled to the plurality of charging control modules and selectively distributing charging of the plurality of charging control modules to multiplex distribution of voltage to the plurality of electric vehicles.

  10. Continuous-time cross-phase modulation and quantum computation

    CERN Document Server

    Shapiro, J H; Razavi, Mohsen; Shapiro, Jeffrey H.

    2006-01-01

    The weak nonlinear Kerr interaction between single photons and intense laser fields has been recently proposed as a basis for distributed optics-based solutions to few-qubit applications in quantum communication and computation. Here, we analyze the above Kerr interaction by employing a continuous-time multi-mode model for the input/output fields to/from the nonlinear medium. In contrast to previous single-mode treatments of this problem, our analysis takes into account the full temporal content of the free-field input beams as well as the non-instantaneous response of the medium. The main implication of this model, in which the cross-Kerr phase shift on one input is proportional to the photon flux of the other input, is the existence of phase noise terms at the output. We show that these phase noise terms will degrade the performance of the parity gate proposed by Munro, Nemoto, and Spiller [New J. Phys. 7, 137 (2005)].

  11. Emergence of Long Period Antiferromagnetic Orders from Haldane Phase in S=1 Heisenberg Chains with D-Modulation

    Science.gov (United States)

    Hida, Kazuo; Chen, Wei

    2005-07-01

    The effect of spatial modulation of the single-site anisotropy D on the ground state of the S=1 Heisenberg chains is investigated. In the case of period 2 modulation, it is found that the phase diagram contains the Haldane phase, large-D phase, Néel phase of udud-type and u0d0-type. It is shown that the hidden antiferromagnetic order in the Haldane phase compatible with the spatial modulation of D-term get frozen resulting in the emergence of various types of Néel orders. The investigation of the model with longer period D-modulation also confirms this picture.

  12. Modulation of auroral electrojet currents using dual HF beams with ELF phase offset

    Science.gov (United States)

    Golkowski, M.; Cohen, M.; Moore, R. C.

    2012-12-01

    The modulation of naturally occuring ionospheric currents with high power radio waves in the high frequency (HF, 3-10 MHz) band is a well known technique for generation of extremely low frequency (ELF, 3-3000 Hz) and very low frequency (VLF, 3-30 kHz) waves. We use the heating facility of the High Frequency Active Auroral Research Program (HAARP) to investigate the effect of using dual HF beams with an ELF/VLF phase offset between the modulation waveforms. Experiments with offset HF beams confirm the model of independent ELF/VLF sources. Experiments with co-located HF beams exhibit interaction between the first and second harmonics of the modulated tones when square and sine wave modulation waveforms are employed. Using ELF/VLF phase offsets for co-loacted beams is also shown to be a potential diagnostic for the D-region ionospheric profile.

  13. Study on 8DPSK of multi-phase modulation technology based on CSRZ

    Institute of Scientific and Technical Information of China (English)

    XU Heng-ying; NIU Hui-juan; ZHANG Min; WANG Fang; BAI Cheng-lin; ZHANG Xiao-guang

    2011-01-01

    A new modulation format in optical fiber communication system, the eight differential phase shift keying (8DPSK) of multi-phase modulation technology based on carrier-suppressed return-to-zero (CSRZ) is proposed in this paper. The formulae of CSRZ-8DPSK modem methods are derived theoretically and the methods are demonstrated. Spectra based on CSRZ and CSRZ-8DPSK modulation methods and their eye diagrams by simulation with MATLAB are obtained. The results show that the CSRZ-8DPSK modulation methods have narrower spectra with higher efficiency. The performance of eye diagrams is also much satisfactory after demodulation, suggesting some possible applications of the methods in the next generation of optical fiber communications.

  14. Hybrid Modulation of Bidirectional Three-Phase Dual-Active-Bridge DC Converters for Electric Vehicles

    Directory of Open Access Journals (Sweden)

    Yen-Ching Wang

    2016-06-01

    Full Text Available Bidirectional power converters for electric vehicles (EVs have received much attention recently, due to either grid-supporting requirements or emergent power supplies. This paper proposes a hybrid modulation of the three-phase dual-active bridge (3ΦDAB converter for EV charging systems. The designed hybrid modulation allows the converter to switch its modulation between phase-shifted and trapezoidal modes to increase the conversion efficiency, even under light-load conditions. The mode transition is realized in a real-time manner according to the charging or discharging current. The operation principle of the converter is analyzed in different modes and thus design considerations of the modulation are derived. A lab-scaled prototype circuit with a 48V/20Ah LiFePO4 battery is established to validate the feasibility and effectiveness.

  15. A low-noise delta-sigma phase modulator for polar transmitters.

    Science.gov (United States)

    Zhou, Bo

    2014-01-01

    A low-noise phase modulator, using finite-impulse-response (FIR) filtering embedded delta-sigma (ΔΣ) fractional-N phase-locked loop (PLL), is fabricated in 0.18 μ m CMOS for GSM/EDGE polar transmitters. A simplified digital compensation filter with inverse-FIR and -PLL features is proposed to trade off the transmitter noise and linearity. Experimental results show that the presented architecture performs RF phase modulation well with 20 mW power dissipation from 1.6 V supply and achieves the root-mean-square (rms) and peak phase errors of 4° and 8.5°, respectively. The measured and simulated phase noises of -104 dBc/Hz and -120 dBc/Hz at 400-kHz offset from 1.8-GHz carrier frequency are observed, respectively.

  16. A Low-Noise Delta-Sigma Phase Modulator for Polar Transmitters

    Directory of Open Access Journals (Sweden)

    Bo Zhou

    2014-01-01

    Full Text Available A low-noise phase modulator, using finite-impulse-response (FIR filtering embedded delta-sigma (ΔΣ fractional-N phase-locked loop (PLL, is fabricated in 0.18 μm CMOS for GSM/EDGE polar transmitters. A simplified digital compensation filter with inverse-FIR and -PLL features is proposed to trade off the transmitter noise and linearity. Experimental results show that the presented architecture performs RF phase modulation well with 20 mW power dissipation from 1.6 V supply and achieves the root-mean-square (rms and peak phase errors of 4° and 8.5°, respectively. The measured and simulated phase noises of −104 dBc/Hz and −120 dBc/Hz at 400-kHz offset from 1.8-GHz carrier frequency are observed, respectively.

  17. Tailor the functionalities of metasurfaces: From perfect absorption to phase modulation

    CERN Document Server

    Qu, Che; Hao, Jiaming; Qiu, Meng; Li, Xin; Xiao, Shiyi; Miao, Ziqi; Dai, Ning; He, Qiong; Sun, Shulin; Zhou, Lei

    2015-01-01

    Metasurfaces in metal/insulator/metal configuration have recently been widely used in photonics research, with applications ranging from perfect absorption to phase modulation, but why and when such structures can realize what kind of functionalities are not yet fully understood. Here, based on a coupled-mode theory analysis, we establish a complete phase diagram in which the optical properties of such systems are fully controlled by two simple parameters (i.e., the intrinsic and radiation losses), which are in turn dictated by the geometrical/material parameters of the underlying structures. Such a phase diagram can greatly facilitate the design of appropriate metasurfaces with tailored functionalities (e.g., perfect absorption, phase modulator, electric/magnetic reflector, etc.), demonstrated by our experiments and simulations in the Terahertz regime. In particular, our experiments show that, through appropriate structural/material tuning, the device can be switched across the functionality phase boundaries...

  18. Synchronization and Coherent Combining of Two Pulsed Fiber Ring Lasers Based on Direct Phase Modulation

    Institute of Scientific and Technical Information of China (English)

    WANG Xiao-Lin; ZHOU Pu; MA Hao-Tong; CHEN Zi-Lun; LI Xiao; XU Xiao-Jun; LIU Ze-Jin

    2009-01-01

    We demonstrate a scalable architecture for coherent combining of pulsed fiber ring lasers based on mutual injection and direct phase modulation. By direct phase modulation in the common arm of two ring lasers, synchronous pulsed lasers can be generated and coherent combining of the two synchronous lasers is obtained. Two pulsed fiber ring lasers are coherently combined with 0.55 μJ pulse energy and 10μs pulse duration at a repetition rate of 27.5 kHz. Experimental results show that the two fiber ring lasers are phase locked with an invariable phase difference of π and have good temporal synchronization and spatial coherence. The combining efficiency of the two pulsed fiber laser reaches 90% and the fringe contrast is larger than 40%. Neither active phase control nor polarization control is used in our experiment and this method can be extended to combine more beams and higher repetition rate scaling up to higher power.

  19. Integrated DFB-DBR laser modulator grown by selective area metalorganic vapor phase epitaxy growth technique

    Science.gov (United States)

    Tanbun-Ek, T.; Chen, Y. K.; Grenko, J. A.; Byrne, E. K.; Johnson, J. E.; Logan, R. A.; Tate, A.; Sergent, A. M.; Wecht, K. W.; Sciortine, P. F.; Chu, S. N. G.

    1994-12-01

    A device quality of selective epitaxy growth of InGaAsP/InP multiple quantum well (MQW) structure using low-pressure metalorganic vapor phase epitaxy (MOVPE) technique is described. The technique is applied to a monolithically integrated electroabsorption modulator with distributed feedback (DFB) and distributed Bragg reflector (DBR) lasers. Superior device characteristics such as efficient modulation, low threshold current and high efficiency operation of the integrated devices are obtained.

  20. Stability of Phase-modulated Quantum Key Distribution System

    CERN Document Server

    Han, Z F; Gui, Y Z; Guo, G C; Han, Zheng-Fu; Mo, Xiao-Fan; Gui, You-Zhen; Guo, Guang-Can

    2004-01-01

    Phase drift and random fluctuation of interference visibility in double unbalanced M-Z QKD system are observed and distinguished. It has been found that the interference visibilities are influenced deeply by the disturbance of transmission fiber. Theory analysis shows that the fluctuation is derived from the envioronmental disturbance on polarization characteristic of fiber, especially including transmission fiber. Finally, stability conditions of one-way anti-disturbed M-Z QKD system are given out, which provides a theoretical guide in pragmatic anti-disturbed QKD.

  1. Phase-field modeling of submonolayer growth with the modulated nucleation regime

    Energy Technology Data Exchange (ETDEWEB)

    Dong, X.L.; Xing, H.; Chen, C.L., E-mail: chenchl@nwpu.edu.cn; Wang, J.Y.; Jin, K.X.

    2015-10-16

    In this letter, we perform the phase-field simulations to investigate nucleation regime of submonolayer growth via a quantified nucleation term. Results show that the nucleation related kinetic coefficients have changed the density of islands and critical sizes to modulate the nucleation regime. The scaling behavior of the island density can be agreed with the classical theory only when effects of modulations have been quantified. We expect to produce the quantitative descriptions of nucleation for submonolayer growth in phase-field models. - Highlights: • The phase-field simulations are systematically compared with the classical nucleation rate theory. • The modulations of nucleation regime by the different kinetic coefficients have been studied. • Appropriate kinetic coefficients contribute to the agreed nucleation regime with the scaling law.

  2. Acoustic holography based on composite metasurface with decoupled modulation of phase and amplitude

    Science.gov (United States)

    Tian, Ye; Wei, Qi; Cheng, Ying; Liu, Xiaojun

    2017-05-01

    Acoustic holography has extensive possibilities in acoustic sensing, acoustic illusion, contactless particle manipulation, and medical imaging. Based on coating unit cells and perforated panels, an acoustic composite metasurface is constructed with a decoupled modulation of phase and amplitude, which has been used to design acoustic holography. This proposal not only has lower complexity than conventional acoustic holography of active arrays due to the avoidance of complex structures and circuits but also provides more flexibility than acoustic holography based on the acoustic metasurface with phase-only modulation benefitting from the efficient decoupled modulation of phase and amplitude. We have further demonstrated three acoustic holographic applications, such as multi-directional transmission, multi-focal focusing, and holographic imaging. Due to the low complexity and the great flexibility, this proposal has potential to achieve the high-quality holograms with high information content, fine resolution, and large scale.

  3. High angle phase modulated low coherence interferometry for path length resolved Doppler measurements of multiply scattered light

    NARCIS (Netherlands)

    Varghese, Babu; Rajan, Vinayakrishnan; Leeuwen, van Ton G.; Steenbergen, Wiendelt

    2008-01-01

    We describe an improved method for coherence domain path length resolved measurements of multiply scattered photons in turbid media. An electro-optic phase modulator sinusoidally modulates the phase in the reference arm of a low coherence fiber optic Mach–Zehnder interferometer, at a high phase modu

  4. An Improved Modulation Strategy for the Three-Phase Z-Source Inverters (ZSIs)

    DEFF Research Database (Denmark)

    Abdelhakim, Ahmed; Davari, Pooya; Blaabjerg, Frede

    2017-01-01

    Z-source inverters (ZSIs), compared to the two-stage architecture, i.e. boost-converter (BC)-fed voltage source inverter (VSI), embrace some interesting features, like the reduced size and complexity of the entire conversion system. Several research activities have been established to improve...... the performance of the so-called ZSI since it has been proposed in 2003, and many modifications have been introduced accordingly. These modifications include the structure of the ZSI, i.e. modifying the topology itself, and its modulation. From the modulation prospective, all the modulation strategies of the ZSI......, as the added ST pulses are inserted inside the zero states. Hence, in this digest, an improved modulation strategy is proposed to enhance the performance of the three-phase ZSIs, including all the other improved topologies. The proposed modulation strategy, which is called high-boost-based modified space...

  5. A layered modulation method for pixel matching in online phase measuring profilometry

    Science.gov (United States)

    Li, Hongru; Feng, Guoying; Bourgade, Thomas; Yang, Peng; Zhou, Shouhuan; Asundi, Anand

    2016-10-01

    An online phase measuring profilometry with new layered modulation method for pixel matching is presented. In this method and in contrast with previous modulation matching methods, the captured images are enhanced by Retinex theory for better modulation distribution, and all different layer modulation masks are fully used to determine the displacement of a rectilinear moving object. High, medium and low modulation masks are obtained by performing binary segmentation with iterative Otsu method. The final shifting pixels are calculated based on centroid concept, and after that the aligned fringe patterns can be extracted from each frame. After performing Stoilov algorithm and a series of subsequent operations, the object profile on a translation stage is reconstructed. All procedures are carried out automatically, without setting specific parameters in advance. Numerical simulations are detailed and experimental results verify the validity and feasibility of the proposed approach.

  6. A Compact QPSK Modulator with Low Amplitude and Phase Imbalance for Remote Sensing Applications

    KAUST Repository

    Ghaffar, Farhan Abdul

    2012-09-30

    A new, compact and wide-band Quadrature Phase Shift Keying (QPSK) modulator is presented for remote sensing applications. The microstrip-based modulator employs quadrature hybrid coupler, Wilkinson divider, rat race coupler and GaAs MESFET switches. It is designed to be part of an X band remote sensing transmitter with a center frequency of 8.25GHz. The fabricated module demonstrates the lowest reported amplitude and phase imbalances (0.1dB and 0.4° respectively) around its center frequency. The modulation, tested up to 160 Mbps data rate, displays carrier suppression greater than 30 dB. With negligible DC power consumption and low insertion loss, it operates for a wide bandwidth of 3 GHz (7-10 GHz). The effect of amplitude and phase imbalance is investigated on the performance of the modulator. Finally, a transmitter employing this modulator exhibits an excellent overall Error Vector Magnitude (EVM) of around 8 % that is considerably low as compared to the typically obtained values for such transmitters.

  7. Compact 35μm fiber coupled diode laser module based on dense wavelength division multiplexing of NBA mini-bars

    Science.gov (United States)

    Witte, U.; Traub, M.; Di Meo, A.; Hamann, M.; Rubel, D.; Hengesbach, S.; Hoffmann, D.

    2016-03-01

    We present a compact, modular and cross talk free approach for dense wavelength division multiplexing of high power diode lasers based on ultra-steep dielectric filters. The mini bars consist of 5 narrow stripe broad area emitters with a beam parameter product in the range of 2 mm mrad and a wavelength spacing of 2.5 nm between 2 adjacent emitters. Experimental results for fiber coupling (35 μm core diameter, NA < 0.2) of internally and externally stabilized diode lasers are presented. Optical losses are analyzed and alternative optical designs to overcome the current limitations of the setup are discussed.

  8. Double sinusoidal phase modulating laser diode interferometer for thickness measurements of transparent plates

    Institute of Scientific and Technical Information of China (English)

    Dailin Li(李代林); Xiangzhao Wang(王向朝); Yingming Liu(刘英明)

    2004-01-01

    A double sinusoidal phase modulating (SPM) laser diode interferometer for thickness measurements of a transparent plate is presented. A carrier signal is given to the interference signal by using a piezoelectric transducer, and the SPM interferometry is applied to measure the thickness of a transparent plate. By combining the double-modulation technique with the Bessel function ratio method, the measurement error originating from light intensity fluctuations caused by the modulation current can be decreased greatly.The thicknesses of a glass parallel plate and a quartz glass are measured in real time, and the corresponding experimental results are also given.

  9. Development of ROACH firmware for microwave multiplexed X-ray TES microcalorimeters

    Energy Technology Data Exchange (ETDEWEB)

    Madden, T. J.; Cecil, T. W.; Gades, L. M.; Quaranta, O.; Yan, D.; Miceli, A.; Gard, J. D.

    2016-09-04

    We are developing room temperature electronics based upon the ROACH platform for reading out microwave multiplexed X-ray TES. ROACH is an open-source hardware and software platform featuring a large Xilinx Field Programmable Gate Array (FPGA), Power PC processor, several 10GB Ethernet SFP+ interfaces, and a collection of daughter boards for analog signal generation and acquisition. The combination of a ROACH board, ADC/DAC conversion daughter boards, and hardware for RF mixing allows for the generation and capture of multiple RF tones for reading out microwave multiplexed x-ray TES microcalorimeters. The FPGA is used to generate multiple tones in base band, from 10MHz to 250MHz, which are subsequently mixed to RF in the multiple GHz range and sent through the microwave multiplexer. The tones are generated in the FPGA by storing a large lookup table in Quad Data Rate (QDR) SRAM modules and playing out the waveform to a DAC board. Once the signal has been modulated to RF, passed through the microwave multiplexer, and has been modulated back to base band, the signal is digitized by an ADC board. The tones are modulated to 0Hz by using a FPGA circuit consisting of a polyphase filter bank, several Xilinx FFT blocks, Xilinx CORDIC blocks (for converting to magnitude and phase), and special phase accumulator circuit for mixing to exactly 0Hz. Upwards of 256 channels can be simultaneously captured and written into a bank of 256 First-In-First-Out (FIFO) memories, with each FIFO corresponding to a channel. Individual channel data can be further processed in the FPGA before being streamed through a 10GB Ethernet fiber-optic interface to a Linux system. The Linux system runs software written in Python and QT C++ for controlling the ROACH system, capturing data, and processing data.

  10. Demonstration of in-service wavelength division multiplexing optical-signal-to-noise ratio performance monitoring and operating guidelines for coherent data channels with different modulation formats and various baud rates.

    Science.gov (United States)

    Chitgarha, Mohammad Reza; Khaleghi, Salman; Daab, Wajih; Almaiman, Ahmed; Ziyadi, Morteza; Mohajerin-Ariaei, Amirhossein; Rogawski, Devora; Tur, Moshe; Touch, Joseph D; Vusirikala, Vijay; Zhao, Wendy; Willner, Alan E

    2014-03-15

    We demonstrated a delay-line interferometer (DLI)-based, optical-signal-to-noise ratio (OSNR) monitoring scheme of 100  Gbit/s polarization multiplexed quadrature-phase-shift-keying (PM-QPSK) four-channel WDM at 50-GHz International Telecommunication Union (ITU) grid with data format transparency and baud rate tunability of the OSNR monitor by measuring the OSNR for a 200  Gbit/s PM-16-QAM (25-Gbaud) signal and a 200  Gbit/s PM-QPSK (50-Gbaud) signal. We also explored and studied different monitor parameters, including the shape of the filter spectrum, the bandwidth of the filter, DLI delay, and DLI phase-detuning to determine the design guidelines for a desired level of accuracy for the OSNR monitor in an optical network.

  11. Multiplexity and multireciprocity in directed multiplexes

    CERN Document Server

    Gemmetto, Valerio; Picciolo, Francesco; Ruzzenenti, Franco; Garlaschelli, Diego

    2014-01-01

    In the last few years, the study of multi-layer complex networks has received significant attention. In this work, we provide new measures to analyse dependencies between directed links in different layers of multiplex networks. We show that this requires more than a straightforward extension of the corresponding multiplexity measures that have been developed for undirected multiplexes. In particular, one should take into account the effects of reciprocity, i.e. the tendency of pairs of vertices to establish mutual connections. It is well known that reciprocity is a crucial property of many directed single-layer networks, affecting several dynamical processes taking place on such systems. Here we extend this quantity to directed multiplexes and introduce the notion of multireciprocity, defined as the tendency of links in one layer to be reciprocated by links in a different layer. We introduce multireciprocity measures valid for both binary and weighted networks and then validate these novel quantities on the ...

  12. Modulation Schemes for Single-Phase B6 Converters With Two Asymmetrical Terminal Voltages

    DEFF Research Database (Denmark)

    Qin, Zian; Loh, Poh Chiang; Blaabjerg, Frede

    2016-01-01

    B6 converter uses six switches divided equally among three phase-legs. It has commonly been used as a three-phase rectifier or inverter, mostly under balanced conditions. Three-phase conversion is however not the only area, where B6 converter has been used. The same topology has been tried...... asymmetrical. How these asymmetrical references should be formulated to meet various performance specifications of a single-phase B6 converter is the theme of this paper. Simulation and experimental results have been obtained for verifying the modulation schemes proposed....

  13. Effective Simulation of Quantum Entanglement Based on Classical Fields Modulated with Pseudorandom Phase Sequences

    CERN Document Server

    Fu, Jian; Xu, Yingying; Dong, Hongtao

    2010-01-01

    We demonstrate that n classical fields modulated with n different pseudorandom phase sequences can constitute a 2^n-dimensional Hilbert space that contains tensor product structure. By using classical fields modulated with pseudorandom phase sequences, we discuss effective simulation of Bell states and GHZ state, and apply both correlation analysis and von Neumann entropy to characterize the simulation. We obtain similar results with the cases in quantum mechanics and find that the conclusions can be easily generalized to n quantum particles. The research on simulation of quantum entanglement may be important, for it not only provides useful insights into fundamental features of quantum entanglement, but also yields new insights into quantum computation.

  14. Robust BPSK Impulse Radio UWB-over-Fiber Systems Using Optical Phase Modulation

    DEFF Research Database (Denmark)

    Pham, Tien Thang; Guerrero Gonzalez, Neil; Yu, Xianbin

    2011-01-01

    The impact of fiber dispersion on the performance of optical phase modulated impulse-radio-ultrawideband (IR-UWB) signals is experimentally investigated. 2Gbps BPSK IR-UWB over 78km fiber transmission is successfully achieved by using digital coherent detection......The impact of fiber dispersion on the performance of optical phase modulated impulse-radio-ultrawideband (IR-UWB) signals is experimentally investigated. 2Gbps BPSK IR-UWB over 78km fiber transmission is successfully achieved by using digital coherent detection...

  15. In-vivo retinal imaging by optical coherence tomography using an RSOD-based phase modulator

    Institute of Scientific and Technical Information of China (English)

    Ling WANG; Zhi-hua DING; Guo-hua SHI; Yu-dong ZHANG

    2009-01-01

    Fourier-domain rapid scanning optical delay line (RSOD) was introduced for phase modulation and depth scanning in a time-domain optical coherence tomography (TD-OCT) system. Investigation of parameter optimization of RSOD was conducted.Experiments for RSOD characterization at different parameters of the groove pitch, focal length, galvomirror size, etc. were performed. By implementing the optimized RSOD in our established TD-OCT system with a broadband light source centered at 840 nm with 50 nm bandwidth, in vivo retina imaging of a rabbit was presented, demonstrating the feasibility of high-quality TD-OCT imaging using an RSOD-based phase modulator.

  16. L-Band Transmit/Receive Module for Phase-Stable Array Antennas

    Science.gov (United States)

    Andricos, Constantine; Edelstein, Wendy; Krimskiy, Vladimir

    2008-01-01

    Interferometric synthetic aperture radar (InSAR) has been shown to provide very sensitive measurements of surface deformation and displacement on the order of 1 cm. Future systematic measurements of surface deformation will require this capability over very large areas (300 km) from space. To achieve these required accuracies, these spaceborne sensors must exhibit low temporal decorrelation and be temporally stable systems. An L-band (24-cmwavelength) InSAR instrument using an electronically steerable radar antenna is suited to meet these needs. In order to achieve the 1-cm displacement accuracy, the phased array antenna requires phase-stable transmit/receive (T/R) modules. The T/R module operates at L-band (1.24 GHz) and has less than 1- deg absolute phase stability and less than 0.1-dB absolute amplitude stability over temperature. The T/R module is also high power (30 W) and power efficient (60-percent overall efficiency). The design is currently implemented using discrete components and surface mount technology. The basic T/R module architecture is augmented with a calibration loop to compensate for temperature variations, component variations, and path loss variations as a function of beam settings. The calibration circuit consists of an amplitude and phase detector, and other control circuitry, to compare the measured gain and phase to a reference signal and uses this signal to control a precision analog phase shifter and analog attenuator. An architecture was developed to allow for the module to be bidirectional, to operate in both transmit and receive mode. The architecture also includes a power detector used to maintain a transmitter power output constant within 0.1 dB. The use of a simple, stable, low-cost, and high-accuracy gain and phase detector made by Analog Devices (AD8302), combined with a very-high efficiency T/R module, is novel. While a self-calibrating T/R module capability has been sought for years, a practical and cost-effective solution has

  17. Enhanced nonlinear spectral compression in fiber by external sinusoidal phase modulation

    Science.gov (United States)

    Boscolo, S.; Mouradian, L. Kh; Finot, C.

    2016-10-01

    We propose a new, simple approach to enhance the spectral compression process arising from nonlinear pulse propagation in an optical fiber. We numerically show that an additional sinusoidal temporal phase modulation of the pulse enables efficient reduction of the intensity level of the side lobes in the spectrum that are produced by the mismatch between the initial linear negative chirp of the pulse and the self-phase modulation-induced nonlinear positive chirp. Remarkable increase of both the extent of spectrum narrowing and the quality of the compressed spectrum is afforded by the proposed approach across a wide range of experimentally accessible parameters.

  18. Optimization of phase contrast in bimodal amplitude modulation AFM

    Directory of Open Access Journals (Sweden)

    Mehrnoosh Damircheli

    2015-04-01

    Full Text Available Bimodal force microscopy has expanded the capabilities of atomic force microscopy (AFM by providing high spatial resolution images, compositional contrast and quantitative mapping of material properties without compromising the data acquisition speed. In the first bimodal AFM configuration, an amplitude feedback loop keeps constant the amplitude of the first mode while the observables of the second mode have not feedback restrictions (bimodal AM. Here we study the conditions to enhance the compositional contrast in bimodal AM while imaging heterogeneous materials. The contrast has a maximum by decreasing the amplitude of the second mode. We demonstrate that the roles of the excited modes are asymmetric. The operational range of bimodal AM is maximized when the second mode is free to follow changes in the force. We also study the contrast in trimodal AFM by analyzing the kinetic energy ratios. The phase contrast improves by decreasing the energy of second mode relative to those of the first and third modes.

  19. Optimization of phase contrast in bimodal amplitude modulation AFM.

    Science.gov (United States)

    Damircheli, Mehrnoosh; Payam, Amir F; Garcia, Ricardo

    2015-01-01

    Bimodal force microscopy has expanded the capabilities of atomic force microscopy (AFM) by providing high spatial resolution images, compositional contrast and quantitative mapping of material properties without compromising the data acquisition speed. In the first bimodal AFM configuration, an amplitude feedback loop keeps constant the amplitude of the first mode while the observables of the second mode have not feedback restrictions (bimodal AM). Here we study the conditions to enhance the compositional contrast in bimodal AM while imaging heterogeneous materials. The contrast has a maximum by decreasing the amplitude of the second mode. We demonstrate that the roles of the excited modes are asymmetric. The operational range of bimodal AM is maximized when the second mode is free to follow changes in the force. We also study the contrast in trimodal AFM by analyzing the kinetic energy ratios. The phase contrast improves by decreasing the energy of second mode relative to those of the first and third modes.

  20. Modulation of mixed-phase titania photoluminescence by oxygen adsorption

    Energy Technology Data Exchange (ETDEWEB)

    Pallotti, D.; Orabona, E.; Amoruso, S.; Maddalena, P. [Dipartimento di Fisica, Universitá degli Studi di Napoli “Federico II,” Via Cintia, I-80126 Napoli (Italy); Institute for Superconductors, Oxides and Innovative Materials and Devices, CNR-SPIN, U.O.S. Napoli, Via Cintia, I-80126 Napoli (Italy); Lettieri, S., E-mail: stefano.lettieri@spin.cnr.it [Institute for Superconductors, Oxides and Innovative Materials and Devices, CNR-SPIN, U.O.S. Napoli, Via Cintia, I-80126 Napoli (Italy)

    2014-07-21

    We investigate the effect of oxygen (O{sub 2}) adsorption on photoluminescence properties of mixed-phase titania nanoparticle films deposited by femtosecond pulsed laser deposition, aiming to assess preliminary conclusions about the feasibility of opto-chemical sensing based on titania. We evidence that O{sub 2} produces opposite responses in rutile and anatase photoluminescence efficiency, highlighting interesting potentialities for future double-parametric optical sensing based on titania. The results evidence an important role of lattice oxygen atoms, suggesting that the standard Schottky barrier mechanism driving the response toward gas species in most used metal-oxide sensors (e.g., tin dioxide) is not the only active mechanism in titania.

  1. Reversible phase modulation and hydrogen storage in multivalent VO2 epitaxial thin films

    Science.gov (United States)

    Yoon, Hyojin; Choi, Minseok; Lim, Tae-Won; Kwon, Hyunah; Ihm, Kyuwook; Kim, Jong Kyu; Choi, Si-Young; Son, Junwoo

    2016-10-01

    Hydrogen, the smallest and the lightest atomic element, is reversibly incorporated into interstitial sites in vanadium dioxide (VO2), a correlated oxide with a 3d1 electronic configuration, and induces electronic phase modulation. It is widely reported that low hydrogen concentrations stabilize the metallic phase, but the understanding of hydrogen in the high doping regime is limited. Here, we demonstrate that as many as two hydrogen atoms can be incorporated into each VO2 unit cell, and that hydrogen is reversibly absorbed into, and released from, VO2 without destroying its lattice framework. This hydrogenation process allows us to elucidate electronic phase modulation of vanadium oxyhydride, demonstrating two-step insulator (VO2)-metal (HxVO2)-insulator (HVO2) phase modulation during inter-integer d-band filling. Our finding suggests the possibility of reversible and dynamic control of topotactic phase modulation in VO2 and opens up the potential application in proton-based Mottronics and novel hydrogen storage.

  2. Optimized generation of spatial qudits by using a pure phase spatial light modulator

    Science.gov (United States)

    Varga, J. J. M.; Rebón, L.; Solís-Prosser, M. A.; Neves, L.; Ledesma, S.; Iemmi, C.

    2014-11-01

    We present a method for preparing arbitrary pure states of spatial qudits, namely, D-dimensional (D≥slant 2) quantum systems carrying information in the transverse momentum and position of single photons. For this purpose, a set of D slits with complex transmission are displayed on a spatial light modulator (SLM). In a recent work we have shown a method that requires a single phase-only SLM to control independently the complex coefficients which define the quantum state of dimension D. The amplitude information was codified by introducing phase gratings inside each slit, and the phase value of the complex transmission was added to the phase gratings. After a spatial filtering process, we obtained in the image plane the desired qudit state. Although this method has proven to be a good alternative to compact the previously reported architectures, it presents some features that could be improved. In this paper we present an alternative scheme to codify the required phase values that minimizes the effects of temporal phase fluctuations associated to the SLM where the codification is carried out. In this scheme, the amplitudes are set by appropriate phase gratings addressed at the SLM, while the relative phases are obtained by a lateral displacement of these phase gratings. We show that this method improves the quality of the prepared state and provides very high fidelities of preparation for any state. An additional advantage of this scheme is that a complete 2π modulation is obtained by shifting the grating by one period; hence the encoding is not limited by the phase modulation range achieved by the SLM. Numerical simulations, that take into account the phase fluctuations, show high fidelities for thousands of qubit states covering the whole Bloch sphere surface. Similar analyses are performed for qudits with D = 3 and D = 7.

  3. Phase-dependent spectral control of pulsed modulation instability via dichromatic seed fields

    CERN Document Server

    Brinkmann, Maximilian; Fallnich, Carsten

    2013-01-01

    We investigated experimentally and numerically the spectral control of modulation instability (MI) dynamics via the initial phase relation of two weak seed fields. Specifically, we show how second-order modulation instability dynamics exhibit phase-dependent anti-correlated growth rates of adjacent spectral sidebands. This effect enables a novel method to control MI-based frequency conversion: in contrast to first-order MI dynamics, which exhibit a uniform phase dependence of the growth rates, second-order MI dynamics allow to redistribute the spectral energy, leading to an asymmetric spectrum. Therefore, the presented findings should be very attractive to different applications, such as phase-sensitive amplification or supercontinuum generation initiated by MI.

  4. Quantitative security evaluation of optical encryption using hybrid phase- and amplitude-modulated keys.

    Science.gov (United States)

    Sarkadi, Tamás; Koppa, Pál

    2012-02-20

    In the increasing number of system approaches published in the field of optical encryption, the security level of the system is evaluated by qualitative and empirical methods. To quantify the security of the optical system, we propose to use the equivalent of the key length routinely used in algorithmic encryption. We provide a calculation method of the number of independent keys and deduce the binary key length for optical data encryption. We then investigate and optimize the key length of the combined phase- and amplitude-modulated key encryption in the holographic storage environment, which is one of the promising solutions for the security enhancement of single- and double-random phase-encoding encryption and storage systems. We show that a substantial growth of the key length can be achieved by optimized phase and amplitude modulation compared to phase-only encryption. We also provide experimental confirmation of the model results.

  5. Preparing arbitrary pure states of spatial qudits with a single phase-only spatial light modulator

    Science.gov (United States)

    Varga, J. J. M.; Solís-Prosser, A. M. A.; Rebón, L.; Arias, A.; Neves, L.; Iemmi, C.; Ledesma, S.

    2015-04-01

    We present a new method for preparing multidimensional spatial qudits by means of a single phase-only spatial light modulator (SLM). This method improves previous ones that use two SLMs, one working in amplitude regime and the other in phase regime. To that end, we addressed diffraction gratings on the slits that define the state and then we performed a spatial filtering in the Fourier plane. The amplitude of the coefficients of the quantum state are determined by the modulation deep of the diffraction gratings, and the relative phase is the mean phase value of the diffraction gratings. This encoding result to be more compact, less expensive and use the photons more efficiently.

  6. A continuously tunable microwave photonic notch filter with complex coefficient based on phase modulation

    Science.gov (United States)

    Xu, Dong; Cao, Ye; Tong, Zheng-rong; Yang, Jing-peng

    2017-01-01

    A continuously tunable microwave photonic notch filter with complex coefficient based on phase modulation is proposed and demonstrated. The complex coefficient is generated using a Fourier-domain optical processor (FD-OP) to control the amplitude and phase of the optical carrier and radio-frequency (RF) phase modulation sidebands. By controlling the FD-OP, the frequency response of the filter can be tuned in the full free spectral range ( FSR) without changing the shape and the FSR of the frequency response. The results show that the center frequency of the notch filter can be continuously tuned from 17.582 GHz to 29.311 GHz with FSR of 11.729 GHz. The shape of the frequency response keeps unchanged when the phase is tuned.

  7. Multiplexing encoding method for full-color dynamic 3D holographic display.

    Science.gov (United States)

    Xue, Gaolei; Liu, Juan; Li, Xin; Jia, Jia; Zhang, Zhao; Hu, Bin; Wang, Yongtian

    2014-07-28

    The multiplexing encoding method is proposed and demonstrated for reconstructing colorful images accurately by using single phase-only spatial light modulator (SLM). It will encode the light waves at different wavelengths into one pure-phase hologram at the same time based on the analytic formulas. The three-dimensional (3D) images can be reconstructed clearly when the light waves at different wavelengths are incident into the encoding hologram. Numerical simulations and optical experiments for 2D and 3D colorful images are performed. The results show that the colorful reconstructed images with high quality are achieved successfully. The proposed multiplexing method is a simple and fast encoding approach and the size of the system is small and compact. It is expected to be used for realizing full-color 3D holographic display in future.

  8. Sandpiles on multiplex networks

    CERN Document Server

    Lee, Kyu-Min; Kim, I -M

    2011-01-01

    We introduce the sandpile model on multiplex networks with more than one type of edges and investigate its scaling and dynamical behaviors. We find that the introduction of multiplexity does not alter the scaling behavior of avalanche dynamics; the system is critical with the asymptotic power-law avalanche size distribution with exponent $\\tau = 3/2$ on duplex random networks. Detailed cascade dynamics, however, is affected by the multiplex coupling. For example, higher-degree nodes such as hubs in scale-free networks fail more often in the multiplex dynamics than in the simplex network counterpart in which different types of edges are simply aggregated. Our results suggest that multiplex modeling would be necessary in order to gain better understanding of cascading failure phenomena of real-world multiplex complex systems, such as the global economic crisis.

  9. Weighted Multiplex Networks

    CERN Document Server

    Menichetti, Giulia; Panzarasa, Pietro; Mondragón, Raúl J; Bianconi, Ginestra

    2013-01-01

    One of the most important challenges in network science is to quantify the information encoded in complex network structures. Disentangling randomness from organizational principles is even more demanding when networks have a multiplex nature. Multiplex networks are multilayer systems of $N$ nodes that can be linked in multiple interacting and co-evolving layers. In these networks, relevant information might not be captured if the single layers were analyzed separately. Here we demonstrate that such partial analysis of layers fails to capture significant correlations between weights and topology of complex multiplex networks. To this end, we study two weighted multiplex co-authorship and citation networks involving the authors included in the American Physical Society. We show that in these networks weights are strongly correlated with multiplex structure, and provide empirical evidence in favor of the advantage of studying weighted measures of multiplex networks, such as multistrength and the inverse multipa...

  10. In-Phase Wavelength Conversion Based On Cross-Gain Modulation in Semiconductor Optical Amplifier

    Institute of Scientific and Technical Information of China (English)

    ZHANG Xinliang; HUANG Dexiu; SUN Junqiang; LIU Deming; YI Heqing

    2000-01-01

    In-phase wavelength conversion based on cross-gain modulation in a semiconductor optical amplifier biased around critical threshold current has been demonstrated. The converted signal and the pump signal have the same bit sequence 1101011000. The stimulated emission competition between the amplification of input signals and the amplified spontaneous emission was used to illustrate the conversion mechanism. Experiment results showed that in-phase wavelength conversion can be achieved with simple structure and high output extinction ratio.

  11. Identifying communities from multiplex biological networks

    Directory of Open Access Journals (Sweden)

    Gilles Didier

    2015-12-01

    Full Text Available Various biological networks can be constructed, each featuring gene/protein relationships of different meanings (e.g., protein interactions or gene co-expression. However, this diversity is classically not considered and the different interaction categories are usually aggregated in a single network. The multiplex framework, where biological relationships are represented by different network layers reflecting the various nature of interactions, is expected to retain more information. Here we assessed aggregation, consensus and multiplex-modularity approaches to detect communities from multiple network sources. By simulating random networks, we demonstrated that the multiplex-modularity method outperforms the aggregation and consensus approaches when network layers are incomplete or heterogeneous in density. Application to a multiplex biological network containing 4 layers of physical or functional interactions allowed recovering communities more accurately annotated than their aggregated counterparts. Overall, taking into account the multiplexity of biological networks leads to better-defined functional modules. A user-friendly graphical software to detect communities from multiplex networks, and corresponding C source codes, are available at GitHub (https://github.com/gilles-didier/MolTi.

  12. Two-dimensional refractive index modulation by phased array transducers in acousto-optic deflectors.

    Science.gov (United States)

    Wang, Tiansi; Zhang, Chong; Aleksov, Aleksandar; Salama, Islam; Kar, Aravinda

    2017-01-20

    Acousto-optic deflectors are photonic devices that are used for scanning high-power laser beams in advanced microprocessing applications such as marking and direct writing. The operation of conventional deflectors mostly relies on one-dimensional sinusoidal variation of the refractive index in an acousto-optic medium. Sometimes static phased array transducers, such as step configuration or planar configuration transducer architecture, are used to tilt the index modulation planes for achieving higher performance and higher resolution than a single transducer AO device. However, the index can be modulated in two dimensions, and the modulation plane can be tilted arbitrarily by creating dynamic phase gratings in the medium using phased array transducers. This type of dynamic two-dimensional acousto-optic deflector can provide better performance using, for example, a large deflection angle and high diffraction efficiency. This paper utilizes an ultrasonic beam steering approach to study the two-dimensional strain-induced index modulation due to the photoelastic effect. The modulation is numerically simulated, and the effects of various parameters, such as the operating radiofrequency of the transducers, the ultrasonic beam steering angle, and different combinations of pressure on each element of the transducer array, are demonstrated.

  13. Phase-noise characteristics of a 25-GHz-spaced optical frequency comb based on a phase- and intensity-modulated laser.

    Science.gov (United States)

    Ishizawa, Atsushi; Nishikawa, Tadashi; Mizutori, Akira; Takara, Hidehiko; Takada, Atsushi; Sogawa, Tetsuomi; Koga, Masafumi

    2013-12-02

    We investigated phase-noise characteristics of both a phase/intensity-modulated laser with 25-GHz mode spacing and a mode-locked fiber laser with carrier-envelope-offset (CEO) locking. As the separation from the frequency of the continuous wave (CW) laser diode (LD) for a seed light source increases, the integrated phase noise of each comb mode of both the phase/intensity-modulated laser and supercontinuum light originating from it increases with the same slope as a function of mode number. The dependence of the integrated phase noise on mode number with the phase/intensity-modulated laser is much larger than with the mode-locked fiber laser of the CEO locking. However, the phase noise of the phase/intensity-modulated laser is extremely lower than that of the mode-locked fiber laser with CEO locking in the frequency region around the CW LD. The phase noise of the phase/intensity-modulated laser with 25-GHz mode spacing and that of the mode-locked fiber laser with the CEO locking could be estimated and were found to be almost the same at the wavelengths required in an f-to-2f self-referencing interferometer. Our experimental results indicate the possibility of achieving an offset-frequency-locked frequency comb with the phase/intensity-modulated laser.

  14. Single pulse TMS-induced modulations of resting brain neurodynamics encoded in EEG phase.

    Science.gov (United States)

    Stamoulis, Catherine; Oberman, Lindsay M; Praeg, Elke; Bashir, Shahid; Pascual-Leone, Alvaro

    2011-06-01

    Integration of electroencephalographic (EEG) recordings and transcranial magnetic stimulation (TMS) provides a useful framework for quantifying stimulation-induced modulations of neural dynamics. Amplitude and frequency modulations by different TMS protocols have been previously investigated, but the study of stimulation-induced effects on EEG phase has been more limited. We examined changes in resting brain dynamics following single TMS pulses, focusing on measures in the phase domain, to assess their sensitivity to stimulation effects. We observed a significant, approximately global increase in EEG relative phase following prolonged (>20 min) single-pulse TMS. In addition, we estimated higher rates of phase fluctuation from the slope of estimated phase curves, and higher numbers of phase resetting intervals following TMS over motor cortex, particularly in frontal and centro-parietal/parietal channels. Phase changes were only significantly different from their pre-TMS values at the end of the stimulation session, which suggests that prolonged single-pulse TMS may result in cumulative changes in neural activity reflected in the phase of the EEG. This is a novel result, as prior studies have reported only transient stimulation-related effects in the amplitude and frequency domains following single-pulse TMS.

  15. Coherent Control of Photofragment Distributions Using Laser Phase Modulation in the Weak-Field Limit

    DEFF Research Database (Denmark)

    Garcia-Vela, Alberto; Henriksen, Niels Engholm

    2015-01-01

    The possibility of quantum interference control of the final state distributions of photodissociation fragments by means of pure phase modulation of the pump laser pulse in the weak-field regime is demonstrated theoretically for the first time. The specific application involves realistic wave pac...

  16. Self-phase modulation of a single-cycle THz pulse

    DEFF Research Database (Denmark)

    Turchinovich, Dmitry; Hvam, Jørn Märcher; Hoffmann, M. C.

    2013-01-01

    We demonstrate self-phase modulation (SPM) of a single-cycle THz pulse in a semiconductor, using bulk n-GaAs as a model system. The SPM arises from the heating of free electrons in the electric field of the THz pulse. Electron heating leads to an ultrafast reduction of the plasma frequency, which...

  17. Effects of nonlinear phase modulation on Bragg scattering in the low-conversion regime

    DEFF Research Database (Denmark)

    Andersen, Lasse Mejling; Cargill, D. S.; McKinstrie, C. J.

    2012-01-01

    In this paper, we consider the effects of nonlinear phase modulation on frequency conversion by four-wave mixing (Bragg scattering) in the low-conversion regime. We derive the Green functions for this process using the time-domain collision method, for partial collisions, in which the four fields...

  18. Multiband carrierless amplitude/phase modulation for ultra-wideband high data rate wireless communications

    DEFF Research Database (Denmark)

    Puerta Ramírez, Rafael; Rommel, Simon; Altabas, Jose A.

    2016-01-01

    We report on the first experimental demonstration of carrierless amplitude/phase modulation in a flexible multiband approach for ultrawideband high-data-rate wireless communications. An effective bitrate of 2 GB/s is achieved while complying with the restrictions on the effective radiated power e...

  19. Sub-millisecond, high stroke phase modulation using polymer network liquid crystals.

    Science.gov (United States)

    Love, Gordon D; Kirby, Andrew K; Ramsey, Robert A

    2010-03-29

    We describe the production of a high speed, and high stroke, phase modulator using a polymer network liquid crystal device. We present data showing fast response times (sub millisecond) in a device which can operate at visible wavelengths with a simple electrical addressing scheme.

  20. Effects of nonlinear phase modulation on low-conversion four-wave mixing Bragg scattering

    DEFF Research Database (Denmark)

    Andersen, Lasse Mejling; McKinstrie, C. J.; Rottwitt, Karsten

    We consider the effects of nonlinear phase modulation (NPM) on frequency converseon by Bragg scattering. Previously we found that arbitrary mode reshaping without temporal entanglement (separability) was possible. When NPM is included, the modes are chirped and the separability is no longer compl...

  1. Phase-dependent modulation of short latency cutaneous reflexes during walking in man.

    NARCIS (Netherlands)

    Baken, B.C.M.; Dietz, V.; Duysens, J.E.J.

    2005-01-01

    In reduced animal preparation (cat fictive locomotion) most of our knowledge on the phase-dependent modulation of cutaneous reflexes concerns early- (P1 responses) rather than medium-latency (P2) responses. In contrast, in humans, virtually only P2 responses have been studied because P1 responses ar

  2. Coherent control of quantum transport: modulation-enhanced phase detection and band spectroscopy

    CERN Document Server

    Tarallo, Marco G; Wang, F Y; Tino, Guglielmo M

    2012-01-01

    Amplitude modulation of a tilted optical lattice can be used to steer the quantum transport of matter wave packets in a very flexible way. This allows the experimental study of the phase sensitivity in a multimode interferometer based on delocalization-enhanced Bloch oscillations and to probe the band structure modified by a constant force.

  3. Methods, systems and apparatus for adjusting modulation index to improve linearity of phase voltage commands

    Energy Technology Data Exchange (ETDEWEB)

    Gallegos-Lopez, Gabriel; Perisic, Milun; Kinoshita, Michael H.

    2017-03-14

    Embodiments of the present invention relate to methods, systems and apparatus for controlling operation of a multi-phase machine in a motor drive system. The disclosed embodiments provide a mechanism for adjusting modulation index of voltage commands to improve linearity of the voltage commands.

  4. Low Power Penalty Operation of a Wide Input Dynamic Range Cross-Phase Modulation Wavelength Converter

    Institute of Scientific and Technical Information of China (English)

    Jun; Endo; Akira; Ohki; Rieko; Sato; Toshio; Ito; Yuichi; Tohmori; Yasuhiro; Suzuki

    2003-01-01

    We successfully demonstrated low power penalty operation of a cross-phase modulated (XPM) wavelength converter using a semiconductor optical amplifier (SOA) power equalizer. We also clarified the SOA equalizing level for more adaptive wavelength conversion and achieved a power penalty of less than 1 dB over the wide input dynamic range of 15 dB.

  5. High Capacity Phase/Amplitude Modulated Optical Communication Systems and Nonlinear Inter-Channel Impairments

    Science.gov (United States)

    Tavassoli, Vahid

    This thesis studies and mathematically models nonlinear interactions among channels of modern high bit rate (amplitude/) phase modulated optical systems. First, phase modulated analogue systems are studied and a differential receiving method is suggested with experimental validation. The main focus of the rest of the thesis is on digital advanced modulation format systems. Cross-talk due to fiber Kerr nonlinearity in two-format hybrid systems as well as 16-QAM systems is mathematically modelled and verified by simulation for different system parameters. A comparative study of differential receivers and coherent receivers is also given for hybrid systems. The model is based on mathematically proven assumptions and provides an intuitive analytical understanding of nonlinear cross-talk in such systems.

  6. Photonic aided bandpass sampling in coherent phase modulated radio-over-fiber links

    Science.gov (United States)

    Cao, Minghua; Li, Jianqiang; Dai, Jian; Dai, Yitang; Yin, Feifei; Zhou, Yue; Xu, Kun

    2016-06-01

    We have experimentally presented a digital coherent receiver employing photonic aided bandpass sampling technology for phase-modulated radio-over-fiber (RoF) links. An optical intensity modulator (IM) is utilized as the bandpass sampler which performs encoded on-off keyed pulse sequence on the optical local oscillator. Quaternary Phase Shift Keying (QPSK) modulated data signal with 20 MHz bandwidth at 5.2 GHz, 10.2 GHz and 15.2 GHz RF carrier frequency is experimentally demonstrated to be successfully detected by using balanced photodiodes (BPDs) with only 800 MHz analog bandwidth. It demonstrates that the required analog bandwidth of BPDs and ADCs can be dramatically reduced in a direct sampled coherent RoF communications system.

  7. Calibration of photoelastic modulator based dichrometers: maintaining constant phase across the spectrum

    Science.gov (United States)

    Sutherland, J. C.

    2016-07-01

    Photoelastic modulators can alter the polarization state of a beam of ultraviolet, visible or infrared photons by means of periodic stress-induced differences in the refractive index of a transparent material that forms the optical element of the device and is isotropic in the absence of stress. They have found widespread application in instruments that characterize or alter the polarization state of a beam in fields as diverse as astronomy, structural biology, materials science and ultraviolet lithography for the manufacture of nano-scale integrated circuits. Measurement of circular dichroism, the differential absorption of left- and right circularly polarized light, and of strain-induced birefringence of optical components are major applications. Instruments using synchrotron radiation and photoelastic modulators with CaF2 optical elements have extended circular dichroism measurements down to wavelengths of about 130 nm in the vacuum ultraviolet. Maintaining a constant phase shift between two orthogonal polarization states across a spectrum requires that the amplitude of the modulated stress be changed as a function of wavelength. For commercially available photoelastic modulators, the voltage that controls the amplitude of modulation required to produce a specified phase shift, which is a surrogate for the stress modulation amplitude, has been shown to be an approximately linear function of wavelength in the spectral region where the optical element is transparent. But, extrapolations of such straight lines cross zero voltage at a non-zero wavelength, not at zero-wavelength. For modulators with calcium fluoride and fused silica optical elements, the zero-crossing wavelength is always in the spectral region where the optical element of the modulator strongly absorbs the incident radiation, and at a wavelength less than the longest-wavelength apparent resonance deduced from experimental values of the refractive index fit to the Sellmeier equation. Using a model

  8. Superluminescent diode interferometer using sinusoidal phase modulation for step-profile measurement.

    Science.gov (United States)

    Sasaki, O; Ikeada, Y; Suzuki, T

    1998-08-01

    We propose an interferometer in which the relationship between the degree of coherence (DCH) and the optical path difference (OPD) is utilized for determining an OPD longer than a wavelength. A superluminescent diode is employed as the source of the interferometer, and sinusoidal phase-modulating interferometry is used to detect the DCH and the phase of the interference signal. The combination of the OPD determined from the DCH and the phase of an interference signal enables us to measure an OPD longer than a wavelength with a high accuracy of a few nanometers. Experimental results show clearly the usefulness of the interferometer for a step-profile measurement.

  9. Cross-phase modulation instability in mode-locked laser based on reduced graphene oxide

    CERN Document Server

    Gaol, Lei; Liu, Min; Huang, Wei

    2014-01-01

    Cross-phase modulation instability (XPMI) is experimentally observed in a fiber ring cavity with net normal dispersion and mode-locked by long fiber taper. The taper is deposited with reduced graphene oxide, which can decrease the threshold of XPMI due to the enhanced nonlinearity realized by 8 mm evanescent field interaction length and strong mode confinement. Experimental results indicate that the phase matching conditions in two polarization directions are different, and sidebands with different intensities are generated. This phase matching condition can be satisfied even the polarization state of the laser varies greatly under different pump strengths.

  10. Measurement of the amplitude and phase transfer functions of an optical modulator using a heterodyne technique

    DEFF Research Database (Denmark)

    Romstad, Francis Pascal; Birkedal, Dan; Mørk, Jesper

    2001-01-01

    We present a new technique that measures the full amplitude and phase transfer curves of the modulator as a function of the applied bias, from which the small signal α-parameter can be calculated. The technique measures the amplitude and phase transfer functions simultaneously and directly......, compared to techniques where a time-consuming data analysis is necessary to calculate the a-parameter and an additional measurement is necessary to estimate the phase. Additionally, the chirp profile for all operation points can be calculated....

  11. APPLICATION OF SPATIAL LIGHT MODULATORS FOR GENERATION OF LASER BEAMS WITH A SPIRAL PHASE DISTRIBUTION

    Directory of Open Access Journals (Sweden)

    A. A. Zinchik

    2015-09-01

    Full Text Available Subject of Research. This paper discusses numerical simulation of spiral beams. Spiral beams have been experimentally obtained with the use of liquid crystal spatial light modulators (LCD SLM. The ability of dynamical change for the laser beam parameters has been studied. Method. Spiral beams are traditionally obtained by means of static masks defining the amplitude and phase distribution of the beam. The paper deals with modernized method with the use of two LCD SLMs. Modulators form separately the amplitude and phase distribution of the laser beam. Main Results. Numerical modeling of space spiral beams with different amplitude and phase characteristics has been carried out with the use of VirtualLab 5.0 software package manufactured by LightTrans GmbH. Simulation results are compared to the results of a natural experiment. Experimental results are in good agreement with computer simulation. It is shown that LCD SLMs application gives the possibility for dynamical change of the spiral beam parameters, their structure and the dependence of rotation angle on the distance. Distribution phase inversion leads to a change in the rotation direction of the laser beam and, therefore, to a change in the direction of its orbital angular momentum. Practical Relevance. The use of spatial modulators makes it possible to change dynamically the beam parameters, including rotation direction change. The results can be applied for solution of problems related to laser manipulating of microparticles, as well as the problems of determining the phase inhomogeneities of transparent objects.

  12. Phase-modulated waveform design for extended target detection in the presence of clutter.

    Science.gov (United States)

    Gong, Xuhua; Meng, Huadong; Wei, Yimin; Wang, Xiqin

    2011-01-01

    The problem to be addressed in this paper is a phase-modulated waveform design for the detection of extended targets contaminated by signal-dependent noise (clutter) and additive noise in practical radar systems. An optimal waveform design method that leads to the energy spectral density (ESD) of signal under the maximum signal-to-clutter-and-noise ratio (SCNR) criterion is introduced first. In order to make full use of the transmission power, a novel phase-iterative algorithm is then proposed for designing the phase-modulated waveform with a constant envelope, whose ESD matches the optimal one. This method is proven to be able to achieve a small SCNR loss by minimizing the mean-square spectral distance between the optimal waveform and the designed waveform. The results of extensive simulations demonstrate that our approach provides less than 1 dB SCNR loss when the signal duration is greater than 1 μs, and outperforms the stationary phase method and other phase-modulated waveform design methods.

  13. Phase-Modulated Waveform Design for Extended Target Detection in the Presence of Clutter

    Directory of Open Access Journals (Sweden)

    Xiqin Wang

    2011-07-01

    Full Text Available The problem to be addressed in this paper is a phase-modulated waveform design for the detection of extended targets contaminated by signal-dependent noise (clutter and additive noise in practical radar systems. An optimal waveform design method that leads to the energy spectral density (ESD of signal under the maximum signal-to-clutter-and-noise ratio (SCNR criterion is introduced first. In order to make full use of the transmission power, a novel phase-iterative algorithm is then proposed for designing the phase-modulated waveform with a constant envelope, whose ESD matches the optimal one. This method is proven to be able to achieve a small SCNR loss by minimizing the mean-square spectral distance between the optimal waveform and the designed waveform. The results of extensive simulations demonstrate that our approach provides less than 1 dB SCNR loss when the signal duration is greater than 1 μs, and outperforms the stationary phase method and other phase-modulated waveform design methods.

  14. Spiral versus modulated collinear phases in the quantum axial next-nearest-neighbor Heisenberg model

    Science.gov (United States)

    Oitmaa, J.; Singh, R. R. P.

    2016-12-01

    Motivated by the discovery of spiral and modulated collinear phases in several magnetic materials, we investigate the magnetic properties of Heisenberg spin S =1 /2 antiferromagnets in two and three dimensions, with frustration arising from second-neighbor couplings in one axial direction [the axial next-nearest-neighbor Heisenberg (ANNNH) model]. Our results clearly demonstrate the presence of an incommensurate spiral phase at T =0 in two dimensions, extending to finite temperatures in three dimensions. The crossover between Néel and spiral order occurs at a value of the frustration parameter considerably above the classical value 0.25, a sign of substantial quantum fluctuations. We also investigate a possible modulated collinear phase with a wavelength of four lattice spacings and find that it has substantially higher energy and hence is not realized in the model.

  15. Spectral Phase Modulation and chirped pulse amplification in High Gain Harmonic Generation

    CERN Document Server

    Wu, Zilu; Krinsky, Sam; Loos, Henrik; Murphy, James; Shaftan, Timur; Sheehy, Brian; Shen, Yuzhen; Wang, Xijie; Yu Li Hua

    2004-01-01

    High Gain Harmonic Generation (HGHG), because it produces longitudinally coherent pulses derived from a coherent seed, presents remarkable possibilities for manipulating FEL pulses. If spectral phase modulation imposed on the seed modulates the spectral phase of the HGHG in a deterministic fashion, then chirped pulse amplification, pulse shaping, and coherent control experiments at short wavelengths become possible. In addition, the details of the transfer function will likely depend on electron beam and radiator dynamics and so prove to be a useful tool for studying these. Using the DUVFEL at the National Synchrotron Light Source at Brookhaven National Laboratory, we present spectral phase analyses of both coherent HGHG and incoherent SASE ultraviolet FEL radiation, applying Spectral Interferometry for Direct Electric Field Reconstruction (SPIDER), and assess the potential for employing compression and shaping techniques.

  16. Reducing coherent noise in interference systems using the phase modulation technique.

    Science.gov (United States)

    Cui, Ji-Wen; Tao, Zhang; Liu, Zhao-Bo; Tan, Jiu-Bin

    2015-08-20

    The phase modulation technique is adopted to reduce the coherent noise that arises from spurious interference. By choosing an appropriate driving signal, the method can reduce the coherent function of coherent noise to a great degree while keeping the coherent function of a coherent signal nearly unchanged. Simulation results show that for the grating interferometer, the phase error caused by coherent noise is reduced by 81.53% on average. For the Twyman interferometer, the fringe quality and contrast deteriorated by coherent noise are significantly improved. Furthermore, an experiment is set up in the phase-modulated Twyman interferometer to verify the feasibility of the principle. It is concluded that the method is effective to reduce the coherent noise in interference systems.

  17. Phase Noise Monitor and Reduction by Parametric Saturation Approach in Phase Modulation Systems

    Institute of Scientific and Technical Information of China (English)

    XU Ming; ZHOU Zhen; PU Xiao; JI Jian-Hua; YANG Shu-Wen

    2011-01-01

    Nonlinear phase noise (NLPN) is investigated theoretically and numerically to be mitigated by parametric saturation approach in DPSK systems.The nonlinear propagation equation that incorporates the phase of linear and nonlinear is analyzed with parametric saturation processing (PSP).The NLPN is picked and monitored with the power change factors in the DPSK system.This process can be realized by an optical PSP limiter and a novel apparatus with feedback MZI.The monitor range of phase noise is 0°-90°, which may be reduced to 0°-45°if the monitor factor is about the Stockes wave but not an anti-Stockes wave.It is shown that DPSK signal performance can be improved based on the parametric saturation approach.%@@ Nonlinear phase noise (NLPN) is investigated theoretically and numerically to be mitigated by parametric saturation approach in DPSK systems.The nonlinear propagation equation that incorporates the phase of linear and nonlinear is analyzed with parametric saturation processing (PSP).The NLPN is picked and monitored with the power change factors in the DPSK system.This process can be realized by an optical PSP limiter and a novel apparatus with feedback MZI.The monitor range of phase noise is 0°-90°, which may be reduced to 0°-45° if the monitor factor is about the Stockes wave but not an anti-Stockes wave.It is shown that DPSK signal performance can be improved based on the parametric saturation approach.

  18. 77 FR 35425 - Crystalline Silicon Photovoltaic Cells and Modules From China; Scheduling of the Final Phase of...

    Science.gov (United States)

    2012-06-13

    ... silicon photovoltaic cells, and modules, laminates, and panels, consisting of crystalline silicon... COMMISSION Crystalline Silicon Photovoltaic Cells and Modules From China; Scheduling of the Final Phase of... crystalline silicon photovoltaic cells and modules, provided for in subheadings 8501.31.80, 8501.61.00,...

  19. Single-Carrier Modulation for Neutral-Point-Clamped Inverters in Three-Phase Transformerless Photovoltaic Systems

    DEFF Research Database (Denmark)

    Guo, Xiaoqiang; Cavalcanti, Marcelo C.; Farias, Alexandre M.;

    2013-01-01

    Modulation strategy is one of the most important issues for three-level neutral-point-clamped inverters in three-phase transformerless photovoltaic systems. A challenge for modulation is how to keep the common-mode voltages constant to reduce the leakage currents. A single-carrier modulation...

  20. Broadband microwave phase shifter based on high speed cross gain modulation in quantum dot semiconductor optical amplifiers

    DEFF Research Database (Denmark)

    Chen, Yaohui; Mørk, Jesper

    2009-01-01

    We present a scheme to achieve tunable ~180 degrees microwave phase shifts at frequencies exceeding 100 GHz based on high speed cross gain modulation in quantum dot semiconductor optical amplifiers.......We present a scheme to achieve tunable ~180 degrees microwave phase shifts at frequencies exceeding 100 GHz based on high speed cross gain modulation in quantum dot semiconductor optical amplifiers....

  1. Performance analysis of variable speed multiphase induction motor with pole phase modulation

    Directory of Open Access Journals (Sweden)

    Liu Huijuan

    2016-09-01

    Full Text Available The pole phase modulation (PPM technique is an effective method to extend speed range and torque capabilities for an integrated starter and hybrid electric vehicles applications. In this paper, the five pole-phase combination types of a multiphase induction motor (IM with 36 stator slots and 36 stator conductors are presented and compared quantitatively by using the time-stepping finite element method (TS-FEM. The 36 stator conductors of the proposed multiphase IM are fed by a 36 leg inverter and the current phase angle and amplitude of each stator conductor can be controlled independently. This paper focuses on the winding connection, the PPM technique and the performance comparative analysis of each pole-phase combination types of the proposed multiphase IM. The flux distribution, air-gap flux density, output torque, core losses and efficiency of five pole-phase combination types have been investigated.

  2. Operators Manual and Technical Reference for the Z-Beamlet Phase Modulation Failsafe System: Version 1.

    Energy Technology Data Exchange (ETDEWEB)

    Armstrong, Darrell J.

    2014-09-01

    The need for pulse energies exceeding 4 kJ and pulse lengths [?] 2 ns in Sandia's Z-Beamlet laser (ZBL) requires that the single-frequency spectrum of its fiber-laser master oscillator be converted to a phase modulated spectrum with a modulation in dex [?] 5. Because accidental injection of single-frequency light into ZBL could result i n damage to optical materials from transverse stimulated Brillouin scattering, the presence of phase modulated (PM) light must be monitored by a reliable failsafe system that can stop a las er shot within of a few 10's of ns following a failure of the PM system. This requirement is met by combining optical heterodyne detection with high-speed electronics to indicate the pres ence or absence of phase modulated light. The transition time for the failsafe signal resultin g from a sudden failure using this technique is approximately 35 ns. This is sufficiently short to safely stop a single-frequency laser pulse from leaving ZBL's regenerative amplifier with a n approximately 35 ns margin of safety. This manual and technical reference contains detai led instructions for daily use of the PM failsafe system and provides enough additional informat ion for its maintenance and repair.

  3. BPSK optical mm-wave signal generation by septupling frequency via a single optical phase modulator

    Science.gov (United States)

    Wu, Peng; Ma, Jianxin

    2016-09-01

    In this paper, we have proposed a novel and simple scheme to generate the BPSK optical millimeter wave (MMW) signal with frequency septupling by using an optical phase modulator (PM) and a wavelength selective switch (WSS). In this scheme, the PM is driven by a radio frequency (RF) BPSK signal at the optimized modulation index of 4.89 to assure the 4th and 3rd-order sidebands have equal amplitudes. An wavelength selective switch (WSS) is used to abstract the -4th and +3rd-order sidebands from the spectrum generated by RF BPSK signal modulating the lightwave to form the BPSK optical MMW signal with frequency septupling the driving RF signal. In these two tones, only the +3rd-order sideband bears the BPSK signal while the -4th-order sideband is unmodulated since the phase information is canceled by the even times multiplication of the phase of BPSK signal. The MMW signal can avoid the pulse walk-off effect and the amplitude fading effect caused by the fiber chromatic dispersion. By adjusting the modulation index to assure the two tones have equal amplitude, the generated optical MMW signal has the maximal opto-electrical conversion efficiency and good transmission performance.

  4. An investigation of the influence of residual amplitude modulation in phase electro-optic modulator on the signal of fiber-optic gyroscope

    Science.gov (United States)

    Pogorelaya, D. A.; Smolovik, M. A.; Strigalev, V. E.; Aleynik, A. S.; Deyneka, I. G.

    2016-08-01

    The investigation is devoted to residual amplitude modulation (RAM) of phase electro-optic modulator, which guides are made in LiNbO3 crystal by Ti diffusion technology. An analysis is presented that shows influence of RAM on the signal of fiber-optic gyroscope. The RAM compensation method is offered.

  5. Selectivity enhancement in photoacoustic gas analysis via phase-sensitive detection at high modulation frequency

    Science.gov (United States)

    Kosterev, Anatoliy (Inventor)

    2010-01-01

    A method for detecting a target fluid in a fluid sample comprising a first fluid and the target fluid using photoacoustic spectroscopy (PAS), comprises a) providing a light source configured to introduce an optical signal having at least one wavelength into the fluid sample; b) modulating the optical signal at a desired modulation frequency such that the optical signal generates an acoustic signal in the fluid sample; c) measuring the acoustic signal in a resonant acoustic detector; and d) using the phase of the acoustic signal to detect the presence of the target fluid.

  6. Effectiveness of rf phase modulation for increasing bunch length in electron storage rings

    Science.gov (United States)

    Orsini; Mosnier

    2000-04-01

    Aiming at increasing the apparent bunch length and hence the beam lifetime in electron storage rings, rf phase modulation near one parametric resonance has been experimentally investigated. Since the possible benefit of this technique depends greatly on the ring parameters, we studied the effect of such a modulation for different rf parameters on the longitudinal emittance. Theoretical predictions and results of simulations are compared and discussed. It is shown that synchrotron radiation tends to spoil the parametric resonance. In particular, a criterion for island survival has been found.

  7. Performance Evaluation of Digital Coherent Receivers for Phase-Modulated Radio-Over-Fiber Links

    DEFF Research Database (Denmark)

    Caballero Jambrina, Antonio; Zibar, Darko; Tafur Monroy, Idelfonso

    2011-01-01

    The performance of optical phase-modulated (PM) radio-over-fiber (RoF) links assisted with coherent detection and digital signal processing (PM-Coh) is analyzed and experimentally demonstrated for next-generation wireless-over-fiber systems. PM-Coh offers high linearity for transparent transport......-bandwidth electronics. Analytical assessment and simulations are used to determine the ultimate performance with respect to laser linewidth, modulation index, and receiver sensitivity. Then, two different scenarios are studied and experimentally demonstrated as an application of PM-Coh links: a high...

  8. High-Quality Ultrashort Pulse Generation Utilizing a Self-Phase Modulation-Based Reshaper

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    An ultrashort 10-GHz pulse generation scheme was successfully demonstrated using a bulk material InGaAsP electroabsorption modulator to generate the seed pulse. A self-phase modulation-based reshaper was used after the adiabatic soliton compression in a comb-like dispersion profiled fiber. Experiments and simulations confirm that the reshaper effectively removes the pulse pedestal and improves the pulse extinction ratio. As a result, the 10-GHz pulse had no pedestal, a high extinction ratio, and a pulse width of only 1.4 ps.

  9. 640 GBd Phase-Correlated OTDM NRZ-OOK Generation and Field Trial Transmission

    DEFF Research Database (Denmark)

    Hu, Hao; Münster, Petr; Palushani, Evarist;

    2013-01-01

    We generate a 640 GBd phase-correlated optical time-division multiplexed (PC-OTDM) return-to-zero ON–OFF keying (RZ-OOK) signal based on cross-phase-modulation-induced cross-polarization rotation in an Al highly nonlinear fiber and a 640 GBd PC-OTDM nonreturn-to-zero (NRZ)-OOK signal by RZ...

  10. Low-Complexity Tracking of Laser and Nonlinear Phase Noise in WDM Optical Fiber Systems

    DEFF Research Database (Denmark)

    Yankov, Metodi Plamenov; Fehenberger, Tobias; Barletta, Luca;

    2015-01-01

    In this paper, the wavelength division multiplexed (WDM) fiber optic channel is considered. It is shown that for ideal distributed Raman amplification (IDRA), the Wiener process model is suitable for the non-linear phase noise due to cross phase modulation from neighboring channels. Based...

  11. Colour hologram projection with an SLM by exploiting its full phase modulation range.

    Science.gov (United States)

    Jesacher, Alexander; Bernet, Stefan; Ritsch-Marte, Monika

    2014-08-25

    We demonstrate independent and simultaneous manipulation of light beams of different wavelengths by a single hologram, which is displayed on a phase-only liquid crystal spatial light modulator (SLM). The method uses the high dynamic phase modulation range of modern SLMs, which can shift the phase of each pixel in a range between 0 up to 10π, depending on the readout wavelength. The extended phase range offers additional degrees of freedom for hologram encoding. Knowing the phase modulation properties of the SLM (i.e. the so-called lookup table) in the entire exploited wavelength range, an exhaustive search algorithm allows to combine different independently calculated 2π-holograms into a multi-level hologram with a phase range extending over several multiples of 2π. The combined multi-level hologram then reconstructs the original diffractive patterns with only small phase errors at preselected wavelengths, thus projecting the desired image fields almost without any crosstalk. We demonstrate this feature by displaying a static hologram at an SLM which is read out with an incoherent red-green-blue (RGB) beam, projecting a color image at a camera chip. This is done for both, a Fourier setup which needs a lens for image focusing, and in a "lensless" Fresnel setup, which also avoids the appearance of a focused zero-order spot in the image center. The experimentally obtained efficiency of a two-colour combination is on the order of 83% for each wavelength, with a crosstalk level between the two colour channels below 2%, whereas a three-colour combination still reaches an efficiency of about 60% and a crosstalk level below 5%.

  12. System design of programmable 4f phase modulation techniques for rapid intensity shaping: a conceptual comparison

    Science.gov (United States)

    Roth, Matthias; Heber, Jörg; Janschek, Klaus

    2016-03-01

    The present study analyses three beam shaping approaches with respect to a light-efficient generation of i) patterns and ii) multiple spots by means of a generic optical 4f-setup. 4f approaches share the property that due to the one-to-one relationship between output intensity and input phase, the need for time-consuming, iterative calculation can be avoided. The resulting low computational complexity offers a particular advantage compared to the widely used holographic principles and makes them potential candidates for real-time applications. The increasing availability of high-speed phase modulators, e.g. on the basis of MEMS, calls for an evaluation of the performances of these concepts. Our second interest is the applicability of 4f methods to high-power applications. We discuss the variants of 4f intensity shaping by phase modulation from a system-level point of view which requires the consideration of application relevant boundary conditions. The discussion includes i) the micro mirror based phase manipulation combined with amplitude masking in the Fourier plane, ii) the Generalized Phase Contrast, and iii) matched phase-only correlation filtering combined with GPC. The conceptual comparison relies on comparative figures of merit for energy efficiency, pattern homogeneity, pattern image quality, maximum output intensity and flexibility with respect to the displayable pattern. Numerical simulations illustrate our findings.

  13. Topological phase transition in hexagonal boron-nitride bilayers modulated by gate voltage

    Science.gov (United States)

    Jin, Guojun; Zhai, Xuechao

    2013-03-01

    We study the gate-voltage modulated electronic properties of hexagonal boron-nitride bilayers with two different stacking structures in the presence of intrinsic and Rashba spin-orbit interactions. Our analytical results show that there are striking cooperation effects arising from the spin-orbit interactions and the interlayer bias voltage. For realizing topological phase transition, in contrast to a gated graphene bilayer for increasing its energy gap, the energy gap of a boron-nitride bilayer is significantly reduced by an applied gate voltage. For the AA stacking-bilayer which has the inversion symmetry, a strong topological phase is found, and there is an interesting reentrant behavior from a normal phase to a topological phase and then to a normal phase again, characterized by the topological index. Therefore, the gate voltage modulated AA-boron nitride bilayer can be taken as a newcomer of the topological insulator family. For the AB stacking-bilayer which is lack of the inversion symmetry, it is always topologically trivial, but exhibits an unusual quantum Hall phase with four degenerate low-energy states localized at a single edge. It is suggested that these theoretical findings could be verified experimentally in the transport properties of boron-nitride bylayers. This research was supported by the NSFC (Nos. 60876065, 11074108), PAPD, and NBRPC (Nos. 2009CB929504, 2011CB922102).

  14. A theoretical study of transient stimulated Brillouin scattering in optical fibers seeded with phase-modulated light.

    Science.gov (United States)

    Zeringue, Clint; Dajani, Iyad; Naderi, Shadi; Moore, Gerald T; Robin, Craig

    2012-09-10

    Beam combining of phase-modulated kilowatt fiber amplifiers has generated considerable interest recently. We describe in the time domain how stimulated Brillouin scattering (SBS) is generated in an optical fiber under phase-modulated laser conditions, and we analyze different phase modulation techniques. The temporal and spatial evolutions of the acoustic phonon, laser, and Stokes fields are determined by solving the coupled three-wave interaction system. Numerical accuracy is verified through agreement with the analytical solution for the un-modulated case and through the standard photon conservation relation for counter-propagating optical fields. As a test for a modulated laser, a sinusoidal phase modulation is examined for a broad range of modulation amplitudes and frequencies. We show that, at high modulation frequencies, our simulations agree with the analytical results obtained from decomposing the optical power into its frequency components. At low modulation frequencies, there is a significant departure due to the appreciable cross talk among the laser and Stokes sidebands. We also examine SBS suppression for a white noise source and show significant departures for short fibers from analytically derived formulas. Finally, SBS suppression through the application of pseudo-random bit sequence modulation is examined for various patterns. It is shown that for a fiber length of 9 m the patterns at or near n=7 provide the best mitigation of SBS with suppression factors approaching 17 dB at a modulation frequency of 5 GHz.

  15. Enhanced wavefront reconstruction by random phase modulation with a phase diffuser

    DEFF Research Database (Denmark)

    Almoro, Percival F; Pedrini, Giancarlo; Gundu, Phanindra Narayan

    2011-01-01

    propagation in free space. The presentation of this technique is carried out using two setups. In the first setup, a diffuser plate is placed at the image plane of a metallic test object. The benefit of randomizing the phase of the object wave is the enhanced intensity recording due to high dynamic range...

  16. Attention and temporal expectations modulate power, not phase, of ongoing alpha oscillations.

    Science.gov (United States)

    van Diepen, Rosanne M; Cohen, Michael X; Denys, Damiaan; Mazaheri, Ali

    2015-08-01

    The perception of near-threshold visual stimuli has been shown to depend in part on the phase (i.e., time in the cycle) of ongoing alpha (8-13 Hz) oscillations in the visual cortex relative to the onset of that stimulus. However, it is currently unknown whether the phase of the ongoing alpha activity can be manipulated by top-down factors such as attention or expectancy. Using three variants of a cross-modal attention paradigm with constant predictable stimulus onsets, we examined if cues signaling to attend to either the visual or the auditory domain influenced the phase of alpha oscillations in the associated sensory cortices. Importantly, intermixed in all three experiments, we included trials without a target to estimate the phase at target presentation without contamination from the early evoked responses. For these blank trials, at the time of expected target and distractor onset, we examined (1) the degree of the uniformity in phase angles across trials, (2) differences in phase angle uniformity compared with a pretarget baseline, and (3) phase angle differences between visual and auditory target conditions. Across all three experiments, we found that, although the cues induced a modulation in alpha power in occipital electrodes, neither the visual condition nor the auditory cue condition induced any significant phase-locking across trials during expected target or distractor presentation. These results suggest that, although alpha power can be modulated by top-down factors such as attention and expectation, the phase of the ongoing alpha oscillation is not under such control.

  17. Multiband Carrierless Amplitude Phase Modulation for High Capacity Optical Data Links

    DEFF Research Database (Denmark)

    Iglesias Olmedo, Miguel; Zuo, Tianjian; Jensen, Jesper Bevensee

    2014-01-01

    packaging. Therefore, increasing effort is now put into the possibility of exploiting higher order modulation formats with increased spectral efficiency and reduced optical transceiver complexity. As these type of links are based on intensity modulation and direct detection, modulation formats relying...... on optical coherent detection can not be straight forwardly employed. As an alternative and more viable solution, this paper proposes the use of carrierless amplitude phase (CAP) in a novel multiband approach (MultiCAP) that achieves record spectral efficiency, increases tolerance towards dispersion......Short range optical data links are experiencing bandwidth limitations making it very challenging to cope with the growing data transmission capacity demands. Parallel optics appears as a valid short-term solution. It is, however, not a viable solution in the long-term because of its complex optical...

  18. Few-Photon All-Optical {\\pi} Phase modulation Based on a Double-{\\Lambda} System

    CERN Document Server

    Chen, Yen-Chun; Lo, Hsiang-Yu; Tsai, Bing-Ru; Yu, Ite A; Chen, Ying-Cheng; Chen, Yong-Fan

    2013-01-01

    We propose an efficient all-optical phase modulation based on a double-{\\Lambda} system and demonstrate a {\\pi} phase shift of a few-photon pulse induced by another few-photon pulse in cold rubidium atoms with this scheme. By changing the phases of the applied laser fields, one can control the property of the double-{\\Lambda} medium. This phase-dependent mechanism makes the double-{\\Lambda} system different form the conventional cross-Kerr-based system which only depends on the applied laser intensities. The proposed scheme provides a new route to generate strong nonlinear interactions between photons, and may have potential for applications in quantum information technologies.

  19. Phase-dependent spectral control of pulsed modulation instability via dichromatic seed fields

    Science.gov (United States)

    Brinkmann, Maximilian; Kues, Michael; Fallnich, Carsten

    2014-09-01

    We investigated experimentally and numerically the spectral control of modulation instability (MI) dynamics via the initial phase relation of two weak seed fields. Specifically, we show how second-order MI dynamics exhibit phase-dependent anti-correlated growth rates of adjacent spectral sidebands. This effect enables a novel method to control MI-based frequency conversion: in contrast to first-order MI dynamics, which exhibit a uniform phase dependence of the growth rates, second-order MI dynamics allow to redistribute the spectral energy, leading to an asymmetric spectrum. Therefore, the presented findings should be very attractive to different applications, such as phase-sensitive amplification or supercontinuum generation initiated by MI.

  20. Fiber-optic project-fringe interferometry with sinusoidal phase modulating system

    Science.gov (United States)

    Zhang, Fukai; Duan, Fajie; Lv, Changrong; Duan, Xiaojie; Bo, En; Feng, Fan

    2013-06-01

    A fiber-optic sinusoidal phase-modulating (SPM) interferometer for fringe projection is presented. The system is based on the SPM technique and makes use of the Mach-Zehnder interferometer structure and Young's double pinhole interference principle to achieve interference fringe projection. A Michelson interferometer, which contains the detection of Fresnel reflection on its fiber end face and interference at one input port of a 3 dB coupler, is utilized to achieve feedback precise control of the fringe phase, which is sensitive to phase drifting produced by the nature of the fiber. The phase diversity for the closed-loop SPM system can be real-time measured with a precision of 3 mrad. External disturbances mainly caused by temperature fluctuations can be reduced to 57 mrad for the fringe map. The experimental results have shown the usefulness of the system.

  1. Phase Quantization Study of Spatial Light Modulator for Extreme High contrast Imaging

    CERN Document Server

    Dou, Jiangpei

    2016-01-01

    Direct imaging of exoplanets by reflected starlight is extremely challenging due to the large luminosity ratio to the primary star. Wave front control is a critical technique to attenuate the speckle noise in order to achieve an extreme high contrast. We present the phase quantization study of spatial light modulator for wave front control to meet the contrast requirement of detection of a terrestrial planet in the habitable zone of a solar-type star. We perform the numerical simulation by employing the SLM with different phase accuracy and actuator numbers, which are related to the achievable contrast. We use an optimization algorithm to solve the quantization problems that is matched to the controllable phase step of the SLM. Two optical configurations are discussed with the SLM located before and after the coronagraph focal plane mask, respectively. The simulation result has constrained the specification for phase accuracy of SLM in above two optical configurations. Finally, we have demonstrated that the S...

  2. All-optical short pulse translation through cross-phase modulation in a VO₂ thin film.

    Science.gov (United States)

    Fardad, Shima; Das, Susobhan; Salandrino, Alessandro; Breckenfeld, Eric; Kim, Heungsoo; Wu, Judy; Hui, Rongqing

    2016-01-15

    VO2 is a promising material for reconfigurable photonic devices due to the ultrafast changes in electronic and optical properties associated with its dielectric-to-metal phase transition. Based on a fiber-optic, pump-probe setup at 1550 nm wavelength window, and by varying the pump-pulse duration, we show that the material phase transition is primarily caused by the pump-pulse energy. For the first time, we demonstrate that the instantaneous optical phase modulation of probe during pump leading edge can be utilized to create short optical pulses at probe wavelength, through optical frequency discrimination. This circumvents the impact of long recovery time well known for the phase transition of VO2.

  3. Compound cavity theory of resonant phase modulation in laser self-mixing ultrasonic vibration measurement

    Science.gov (United States)

    Tao, Yufeng; Wang, Ming; Guo, Dongmei

    2016-07-01

    The theoretical basis of self-mixing interference (SMI) employing a resonant phase modulator is explored to prove its tempting advantages. The adopted method induces a pure phase carrier without increasing system complexity. A simple time-domain signal process is used to estimate modulation depth and precisely track vibrating trail, which promises the flexibility of measuring ultrasonic vibration regardless of the constraint of the Bessel functions. The broad bandwidth, low speckle noise, compact, safe, and easy operating SMI system obtains the best resolution of a poor reflection environment. Numerical simulation discusses the spectrum broadening and errors due to multiple reflections. Experimental results agree with theory coherently and are compared with laser Doppler vibration meter showing a dynamical error better than 20 nm in ultrasonic vibration measurement.

  4. Single phase-change analysis of two different PCMs filled in a heat transfer module

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Dong Gyu; Kang, Chae Dong [Chonbuk National University, Jeonju (Korea, Republic of); Kim, Hyung Kuk [Hyundai Heavy Industries Co., Ulsan (Korea, Republic of)

    2014-07-15

    Phase change material(PCM) is tried to secondary heat source in solar heat pump system. A numerical study of the phase change dominant heat transfer is done with a heat transfer module, which consists of a water path(BRINE), heat transfer plates(HTP), and PCM layers of high-temperature one(HPCM, 78-79 .deg. C) and low-temperature one(LPCM, 28-29 .deg. C). There are five arrangements consisting of BRINE, HTP, HPCM, and LPCM layers in the heat transfer module. The time and heat transfer rate for PCM melting/solidification are compared between arrangements. And the numerical time without convection is compared to the experimental one for melting/solidification. From the numerical analysis, the time for melting/solidification is different to 10 hours, depending on the arrangement.

  5. The nature of relaxation processes revealed by the action signals of phase modulated light fields

    CERN Document Server

    Osipov, Vladimir Al; Hansen, Thorsten; Pullerits, Tõnu; Karki, Khadga Jung

    2016-01-01

    In the article we develop a theory of the action signals induced by the two-photon absorption of two phase modulated laser beams. In such experiments the phase of each laser beams is modulated at the frequencies $\\phi_1$ and $\\phi_2$, respectively, and the nonlinear signals are isolated at frequencies $m\\phi=m(\\phi_1-\\phi_2)$ ($m=0,1,2,\\dots$). We demonstrate that the ratio of the amplitudes of primary ($m=1$) and secondary ($m=2$) signals, $A_{\\phi}:A_{2\\phi}$, can be used as an indicator of the type of relaxation processes taking place in the material. The reference ratio value $4:1$ is achieved for the fast linear relaxation processes, and changes smoothly as the relaxation time increases. In case of bimolecular relaxation the ratio becomes a rapidly changing function of the excitation intensity. Our theoretical findings are supported by the experimental observations.

  6. Optical A/D Quantizer Scheme Based on Parallel Phase Modulators

    Institute of Scientific and Technical Information of China (English)

    LI Zheng

    2005-01-01

    A high-speed and high-resolution optical A/D quantizer is proposed. Its architecture is discussed. Bit circuits are built by using the phase modulators in parallel. Based on the different character of the half-wave voltage for every phase modulator and the polarized bias design of incident light, the RF input signal is coded and transmitted in the form of optical digital signal. According to the principle of the architecture, the high-resolution quantizers with 8-bit and 12-bit, et al. are built, which operate at 100 GS/s.Their quantization noise is invariable almost with bit circuits increasing. The simulation result of 4-bit A/D quantizer is also given.

  7. Alternative approach of conducting phase-modulated all-optical logic gates

    Science.gov (United States)

    Chakraborty, Bikash; Mukhopadhyay, Sourangshu

    2009-03-01

    It is well established that optical devices and components are more advantageous than their electronic counterparts because of inherent parallelism in optics. Basically electronics are found to be very unsuitable in high speed (above gigahertz) data processing systems whereas tremendous operational speed (in the range of terahertz) can be achieved with the help of optics. The parallelism of optics and the properties of low loss transmission make optics a powerful technology for digital computing and processing and in long-range communications. Again it is well established that logic gates are the basic building blocks of any computing or data processing system. Therefore, any optical data processor needs suitable optically run logic gates. A method of conducting phase-modulated all-optical logic gates is proposed. Here we will exploit the advantages of phase modulation not only in processing but also in encoding as well decoding also.

  8. Error minimization method for spectroscopic and phase-modulated ellipsometric measurements on highly transparent thin films

    Energy Technology Data Exchange (ETDEWEB)

    Campmany, J.; Bertran, E.; Canillas, A.; Andujar, J.L.; Costa, J. (Universitat de Barcelona, Catalonia (Spain))

    1993-04-01

    The authors point out that there is an intrinsic magnification of error in the measurement of transparent or semitransparent thin films by the usual method of phase-modulated ellipsometry. This procedure is suitable for absorbing materials, but for nonabsorbing materials it gives a great amount of error in the measurement of ellipsometric angles at some critical values. A new methodology is proposed for the phase-modulated ellipsometric measurements that avoids this magnification. The advantages of this new method are illustrated by measuring the index of refraction of a low-pressure chemical-vapor-deposited SiO[sub 2] thin film with greater accuracy than that achieved by the usual method. 16 refs., 6 figs.

  9. Coherent x-ray diffraction imaging of paint pigmentparticles by scanning a phase plate modulator

    Energy Technology Data Exchange (ETDEWEB)

    Chu Y. S.; Chen B.; Zhang F.; Berenguer F.; Bean R.; Kewish C.; Vila-Comamala J.; Rodenburg J.; Robinson I.

    2011-10-19

    We have implemented a coherent x-ray diffraction imaging technique that scans a phase plate to modulate wave-fronts of the x-ray beam transmitted by samples. The method was applied to measure a decorative alkyd paint containing iron oxide red pigment particles. By employing an iterative algorithm for wave-front modulation phase retrieval, we obtained an image of the paint sample that shows the distribution of the pigment particles and is consistent with the result obtained from a transmission x-ray microscope. The technique has been experimentally proven to be a feasible coherent x-ray imaging method with about 120 nm spatial resolution and was shown to work well with industrially relevant specimens.

  10. Digital coherent receiver employing photonic downconversion for phase modulated radio-over-fibre links

    DEFF Research Database (Denmark)

    Zibar, Darko; Caballero Jambrina, Antonio; Guerrero Gonzalez, Neil

    2009-01-01

    A digital coherent receiver employing photonic downconversion is presented and experimentally demonstrated for phase-modulated radio-over-fibre optical links. The receiver is capable of operating at frequencies exceeding the bandwidth of electrical analog-to-digital converter by using photonic...... downconversion to translate the high-frequency input RF signal to the operating frequency range of the analog-to-digital converter. First, using linear digital demodulation scheme we measure SFDR of the link at microwave frequency of 5 GHz. Thereafter, successful signal demodulation of 50 Mbit/s binary phase...... shift keying (BPSK) modulated data signal at 5 GHz RF carrier frequency is experimentally demonstrated by using an analog-to-digital converter with only 1 GHz bandwidth. We successfully demonstrate signal demodulation, using the proposed digital coherent receiver with photonic downconversion, after 40...

  11. Feasibility of a multipurpose transceiver module for phased array radar and EW applications using RFIC technology

    Science.gov (United States)

    Al-Sarawi, Said; Hansen, Hedley; Zhu, Yingbo

    2007-12-01

    Phased array antennas have a large number of civilian and military applications. In this paper we briefly review common approaches to an integrated implementation of radar and electronic warfare digital phase array module and highlight features that are common to both of these applications. Then we discuss how the promising features of the radio frequency integrated circuit (RFIC)-based technology can be utilized in building a transceiver module that meets the requirements of both radar and electronic warfare applications with minimum number of external components. This is achieved by researching the pros and cons of the different receiver architectures and their performance from the targeted applications point of view. Then, we survey current RFIC technologies and highlight the pros and cons of these technologies and how they impact the performance of the discussed receiver architectures.

  12. A novel binaural pitch elicited by phase-modulated noise: MEG and psychophysical observations.

    Science.gov (United States)

    Witton, Caroline; Hillebrand, Arjan; Furlong, Paul L; Henning, G Bruce

    2012-06-01

    Binaural pitches are auditory percepts that emerge from combined inputs to the ears but that cannot be heard if the stimulus is presented to either ear alone. Here, we describe a binaural pitch that is not easily accommodated within current models of binaural processing. Convergent magnetoencephalography (MEG) and psychophysical measurements were used to characterize the pitch, heard when band-limited noise had a rapidly changing interaural phase difference. Several interesting features emerged: First, the pitch was perceptually lateralized, in agreement with the lateralization of the evoked changes in MEG spectral power, and its salience depended on dichotic binaural presentation. Second, the frequency of the pure tone that matched the binaural pitch lay within a lower spectral sideband of the phase-modulated noise and followed the frequency of that sideband when the modulation frequency or center frequency and bandwidth of the noise changed. Thus, the binaural pitch depended on the processing of binaural information in that lower sideband.

  13. Multiplexity and multireciprocity in directed multiplexes

    Science.gov (United States)

    Gemmetto, Valerio; Squartini, Tiziano; Picciolo, Francesco; Ruzzenenti, Franco; Garlaschelli, Diego

    2016-10-01

    Real-world multilayer networks feature nontrivial dependencies among links of different layers. Here we argue that if links are directed, then dependencies are twofold. Besides the ordinary tendency of links of different layers to align as the result of "multiplexity," there is also a tendency to antialign as a result of what we call "multireciprocity," i.e., the fact that links in one layer can be reciprocated by opposite links in a different layer. Multireciprocity generalizes the scalar definition of single-layer reciprocity to that of a square matrix involving all pairs of layers. We introduce multiplexity and multireciprocity matrices for both binary and weighted multiplexes and validate their statistical significance against maximum-entropy null models that filter out the effects of node heterogeneity. We then perform a detailed empirical analysis of the world trade multiplex (WTM), representing the import-export relationships between world countries in different commodities. We show that the WTM exhibits strong multiplexity and multireciprocity, an effect which is, however, largely encoded into the degree or strength sequences of individual layers. The residual effects are still significant and allow us to classify pairs of commodities according to their tendency to be traded together in the same direction and/or in opposite ones. We also find that the multireciprocity of the WTM is significantly lower than the usual reciprocity measured on the aggregate network. Moreover, layers with low (high) internal reciprocity are embedded within sets of layers with comparably low (high) mutual multireciprocity. This suggests that, in the WTM, reciprocity is inherent to groups of related commodities rather than to individual commodities. We discuss the implications for international trade research focusing on product taxonomies, the product space, and fitness and complexity metrics.

  14. Efficient Simulation of Quantum States Based on Classical Fields Modulated with Pseudorandom Phase Sequences

    CERN Document Server

    Fu, Jian

    2010-01-01

    We demonstrate that a tensor product structure could be obtained by introducing pseudorandom phase sequences into classical fields with two orthogonal modes. Using classical fields modulated with pseudorandom phase sequences, we discuss efficient simulation of several typical quantum states, including product state, Bell states, GHZ state, and W state. By performing quadrature demodulation scheme, we could obtain the mode status matrix of the simulating classical fields, based on which we propose a sequence permutation mechanism to reconstruct the simulated quantum states. The research on classical simulation of quantum states is important, for it not only enables potential practical applications in quantum computation, but also provides useful insights into fundamental concepts of quantum mechanics.

  15. Optimization of a four-temporal phase lock for photoelastic-modulated polarimetry.

    Science.gov (United States)

    Tsai, Hsiu-Ming; Chao, Yu-Faye

    2009-08-01

    A set of four-temporal phases in photoelastic-modulated polarimetry is proposed to measure the Stokes parameters. In comparison with the conventional polarimetry, which uses a set of four-spatial angles by rotating a quarter-wave plate to obtain the polarimetric parameters, this temporal type polarimetry not only can reduce the time consumption but also can avoid the measurement error from the beam deviation. In addition, based on singular value decomposition, the figure of merit of this temporal phase technique can improve its signal-to-noise ratio by a factor of 2 in comparison with the rotating quarter-wave plate.

  16. Tight Focusing Properties of Phase Modulated Radially Polarized Laguerre Bessel Gaussian Beam

    Science.gov (United States)

    Prabakaran, K.; Sangeetha, P.; Karthik, V.; Rajesh, K. B.; Musthafa, A. M.

    2017-05-01

    We propose a new approach for generating a multiple focal spot segment of subwavelength size, by tight focusing of a phase modulated radially polarized Laguerre Bessel Gaussian beam. The focusing properties are investigated theoretically by vector diffraction theory. We observe that the focal segment with multiple focal structures is separated with different axial distances and a super long dark channel can be generated by properly tuning the phase of the incident radially polarized Laguerre Bessel Gaussian beam. We presume that such multiple focal patterns and high intense beam may find applications in atom optics, optical manipulations and multiple optical trapping.

  17. Modulated systems in external fields: Conditions for the presence of reentrant phase diagrams

    Science.gov (United States)

    Mendoza-Coto, Alejandro; Billoni, Orlando V.; Cannas, Sergio A.; Stariolo, Daniel A.

    2016-08-01

    We introduce a coarse-grained model capable of describing the phase behavior of two-dimensional ferromagnetic systems with competing exchange and dipolar interactions, as well as an external magnetic field. An improved expression for the mean-field entropic contribution allows us to compute the phase diagram in the whole temperature versus external field plane. We find that the topology of the phase diagram may be qualitatively different depending on the ratio between the strength of the competing interactions. In the regime relevant for ultrathin ferromagnetic films with perpendicular anisotropy we confirm the presence of inverse-symmetry breaking from a modulated phase to a homogeneous one as the temperature is lowered at constant magnetic field, as reported in experiments. For other values of the competing interactions we show that reentrance may be absent. Comparing thermodynamic quantities in both cases, as well as the evolution of magnetization profiles in the modulated phases, we conclude that the reentrant behavior is a consequence of the suppression of domain wall degrees of freedom at low temperatures at constant fields.

  18. Fluorescence-detected two-dimensional electronic coherence spectroscopy by acousto-optic phase modulation.

    Science.gov (United States)

    Tekavec, Patrick F; Lott, Geoffrey A; Marcus, Andrew H

    2007-12-07

    Two-dimensional electronic coherence spectroscopy (ECS) is an important method to study the coupling between distinct optical modes of a material system. Such studies often involve excitation using a sequence of phased ultrashort laser pulses. In conventional approaches, the delays between pulse temporal envelopes must be precisely monitored or maintained. Here, we introduce a new experimental scheme for phase-selective nonlinear ECS, which combines acousto-optic phase modulation with ultrashort laser excitation to produce intensity modulated nonlinear fluorescence signals. We isolate specific nonlinear signal contributions by synchronous detection, with respect to appropriately constructed references. Our method effectively decouples the relative temporal phases from the pulse envelopes of a collinear train of four sequential pulses. We thus achieve a robust and high signal-to-noise scheme for phase-selective ECS to investigate the resonant nonlinear optical response of photoluminescent systems. We demonstrate the validity of our method using a model quantum three-level system-atomic Rb vapor. Moreover, we show how our measurements determine the resonant complex-valued third-order susceptibility.

  19. Experimental Demonstration of Phase Modulation and Motion Sensing Using Graphene-Integrated Metasurfaces

    CERN Document Server

    Dabidian, Nima; Kholmanov, Iskandar; Lu, Feng; Lai, Jongwon Lee Kueifu; Jin, Mingzhou; Fallahazad, Babak; Tutuc, Emanuel; Belkin, Mikhail A; Shvets, Gennady

    2015-01-01

    Plasmonic metasurfaces are able to modify the wavefront by altering the light intensity, phase and polarization state. Active plasmonic metasurfaces would allow dynamic modulation of the wavefront which give rise to interesting application such as beam-steering, holograms and tunable waveplates. Graphene is an interesting material with dynamic property which can be controlled by electrical gating at an ultra-fast speed. We use a graphene integrated metasurface to induce a tunable phase change to the wavefront. The metasurface support a Fano resonance which produces high-quality resonances around 7.7 microns. The phase change is measured using a Michleson interferometry setup. It is shown that the reflection phase changes by about 55 degrees. In particular the phase can change by about 28 degrees while the amplitude is nearly constant. The asymmetric optical response of the metasurface is used to modulate the ellipticity of the reflected wave in response to an incident field at 45 degree. We finally show a pro...

  20. Injection of a Phase Modulated Source into the Z-Beamlet Laser for Increased Energy Extraction.

    Energy Technology Data Exchange (ETDEWEB)

    Rambo, Patrick K.; Armstrong, Darrell J.; Schwarz, Jens; Smith, Ian C; Shores, Jonathon; Speas, Christopher; Porter, John L.

    2014-11-01

    The Z-Beamlet laser has been operating at Sandia National Laboratories since 2001 to provide a source of laser-generated x-rays for radiography of events on the Z-Accelerator. Changes in desired operational scope have necessitated the increase in pulse duration and energy available from the laser system. This is enabled via the addition of a phase modulated seed laser as an alternative front-end. The practical aspects of deployment are discussed here.

  1. Second-Harmonic Generation in Optical Fibres Induced by a Cross-Phase Modulation Effect

    Institute of Scientific and Technical Information of China (English)

    CUI Wei-Na; HUANG Guo-Xiang

    2005-01-01

    @@ When two optical pulses copropagate inside a single-modefibre, intensity-dependent refractive index couples the pulses through a cross-phase modulation (XPM). We show that a second-harmonic generation (SHG) on a continuous-wave background is possible in the optical fibre induced by the XPM effect. By means of a multiscale method the nonlinearly coupled envelope equations for the SHG are derived and their explicit solutions are provided and discussed.

  2. On the application of neural networks to the classification of phase modulated waveforms

    Science.gov (United States)

    Buchenroth, Anthony; Yim, Joong Gon; Nowak, Michael; Chakravarthy, Vasu

    2017-04-01

    Accurate classification of phase modulated radar waveforms is a well-known problem in spectrum sensing. Identification of such waveforms aids situational awareness enabling radar and communications spectrum sharing. While various feature extraction and engineering approaches have sought to address this problem, the use of a machine learning algorithm that best utilizes these features is becomes foremost. In this effort, a comparison of a standard shallow and a deep learning approach are explored. Experiments provide insights into classifier architecture, training procedure, and performance.

  3. Multiplex tokamak power plant

    Energy Technology Data Exchange (ETDEWEB)

    Dabiri, A.E.

    1986-07-01

    The concept of multiplexing for a fusion power core as an option for producing power is explored. Superconducting, as well as normal magnet, coils in either first or second stability regimes are considered. The results show that multiplex plants with superconducting magnets operating in the second stability regime could be competitive with the single-unit plants in some unit sizes. The key issues that impact the expected benefits of multiplexing must be investigated further. These are factory fabrication, economy of scale, the extent of equipment sharing, inherent safety, maintainability, and utility load management.

  4. Mode-locking and Q-switching in multi-wavelength fiber ring laser using low frequency phase modulation.

    Science.gov (United States)

    Jun, Chang Su; Kim, Byoung Yoon

    2011-03-28

    We describe experimental investigation of pulsed output from a multi-wavelength fiber ring laser incorporating low frequency phase modulation with large modulation amplitude. The Erbium-doped fiber (EDF) ring laser generated more than 8 wavelength channels with the help of a phase modulator operating at 26.2 kHz and a periodic intra-cavity filter. For most cases, the laser output is pulsed in the form of mode-locking at 5.62 MHz and/or Q-switching at harmonic and sub-harmonic of the phase modulation frequency. Chaotic pulse output is also observed. The behavior of the output pulses are described as functions of pump power and phase modulation amplitude. The relative intensity noise (RIN) value of a single wavelength channel is measured to be under -100 dB/Hz (-140 dB/Hz beyond 1.5 GHz).

  5. 2D time domain spectral phase encoding/wavelength hopping coherent DPSK-OCDMA system using fiber Bragg gratings and phase modulator

    Science.gov (United States)

    Gao, Zhensen; Dai, Bo; Wang, Xu; Kataoka, Nobuyuki; Wada, Naoya

    2010-12-01

    We propose and experimentally demonstrate a reconfigurable two-dimensional (temporal-spectral) time domain spectral phase encoding (SPE) scheme for coherent optical code-division-multiple-access (OCDMA) application. The time-domain SPE scheme is robust to wavelength drift of the light source and is very flexible and compatible with the fiber optical system. In the proposed scheme, the ultra-short optical pulse is stretched by dispersive device and the SPE is done in time domain using high speed phase modulator. A Fiber Bragg Gratings array is used for generating the two-dimensional wavelength hopping pattern while the high speed phase modulator is used for generating the spectral phase pattern. The proposed scheme can enable simultaneous generation of the time domain spectral phase encoding and DPSK data modulation using only a single phase modulator. In the experiment, the two-dimensional SPE codes have been generated and modulated with 2.5-Gb/s DPSK data using a single phase modulator. Transmission of the 2.5-Gb/s DPSK data over 49km fiber with BER<10-9 has been demonstrated successfully. The proposed scheme exhibits the potential to simplify the architecture and improve the security of the OCDMA system.

  6. A Time-Multiplexed Track-Trigger for the CMS HL-LHC upgrade

    CERN Document Server

    Hall, Geoffrey

    2015-01-01

    A new CMS Tracker is under development for operation at the High Luminosity LHC from 2025. It includes an outer tracker based on special modules of two different types which will construct track stubs using spatially coincident clusters in two closely spaced sensor layers, to reject low transverse momentum track hits and reduce the data volume before data transmission to the Level-1 trigger. The tracker data will be used to reconstruct track segments in dedicated processors before onward transmission to other trigger processors which will combine tracker information with data originating from the calorimeter and muon detectors, to make the final L1 trigger decision. The architecture for processing the tracker data outside the detector is under study, using several alternative approaches. One attractive possibility is to exploit a Time Multiplexed design similar to the one which is currently being implemented in the CMS calorimeter trigger as part of the Phase I trigger upgrade. The novel Time Multiplexed Trig...

  7. High Throughput In Situ DDA Analysis of Neuropeptides by Coupling Novel Multiplex Mass Spectrometric Imaging (MSI) with Gas-Phase Fractionation

    Science.gov (United States)

    OuYang, Chuanzi; Chen, Bingming; Li, Lingjun

    2015-12-01

    Matrix-assisted laser desorption/ionization (MALDI) mass spectrometric imaging (MSI) is a powerful tool to map the spatial distribution of biomolecules on tissue sections. Recent developments of hybrid MS instruments allow combination of different types of data acquisition by various mass analyzers into a single MSI analysis, which reduces experimental time and sample consumptions. Here, using the well-characterized crustacean nervous system as a test-bed, we explore the utility of high resolution and accurate mass (HRAM) MALDI Orbitrap platform for enhanced in situ characterization of the neuropeptidome with improved chemical information. Specifically, we report on a multiplex-MSI method, which combines HRAM MSI with data dependent acquisition (DDA) tandem MS analysis in a single experiment. This method enables simultaneous mapping of neuropeptide distribution, sequence validation, and novel neuropeptide discovery in crustacean neuronal tissues. To enhance the dynamic range and efficiency of in situ DDA, we introduced a novel approach of fractionating full m/z range into several sub-mass ranges and embedding the setup using the multiplex-DDA-MSI scan events to generate pseudo fractionation before MS/MS scans. The division of entire m/z into multiple segments of m/z sub-ranges for MS interrogation greatly decreased the complexity of molecular species from tissue samples and the heterogeneity of the distribution and variation of intensities of m/z peaks. By carefully optimizing the experimental conditions such as the dynamic exclusion, the multiplex-DDA-MSI approach demonstrates better performance with broader precursor coverage, less biased MS/MS scans towards high abundance molecules, and improved quality of tandem mass spectra for low intensity molecular species.

  8. Design and implementation of FPGA-based phase modulation control for series resonant inverters

    Indian Academy of Sciences (India)

    N Gayathri; M C Chandorkar

    2008-10-01

    Owing to the tremendous advances in the digital technology, and improved reliability and performance of the digital control mechanisms, this paper focuses on design and implementation of digital controller using FPGA-based circuit design approach. The digital controller proposed is designed for series resonant inverter used in DC–DC converter applications. Phase modulation technique is proposed for the realization of digital controller on FPGA. The Series Resonant Converter (SRC) is considered in this paper as a preferred converter topology for high power, high voltage power supplies. This paper studies the implementation of phase shift modulation technique using FPGA. The inverter designed, is IGBT based, and Zero Voltage Switching (ZVS) technique is implemented due to reduced stresses on devices and increased efficiency. The phase modulated series resonant inverters (PM-SRC) promotes ZVS operation when its switching frequency is greater than resonant frequency. The designed PM controller is realized using FPGA on which control algorithm and other features of a controller are developed. The series resonant inverter is built and tested for full load under open loop and closed loop conditions at a switching frequency of 20 kHz. The results are presented under varying load conditions. The simulation and the experimental results were found to match closely.

  9. Depth of focus increase by multiplexing programmable diffractive lenses.

    Science.gov (United States)

    Iemmi, C; Campos, J; Escalera, J C; López-Coronado, O; Gimeno, R; Yzuel, M J

    2006-10-30

    A combination of several diffractive lenses written onto a single programmable liquid crystal display (LCD) is proposed for increasing the Depth of Focus (DOF) of the imaging system as a whole. The lenses are spatially multiplexed in a random scheme onto the LCD. The axial irradiance distribution produced by each lens overlaps with the next one producing an extended focal depth. To compare the image quality of the multiplexed lenses, the Modulation Transfer Function (MTF) is calculated. Finally we obtain the experimental Point Spread Functions (PSF) for these multiplexed lenses and experimental results in which an extended object is illuminated under spatially incoherent monochromatic light. We compare the images obtained in the focal plane and in some defocused planes with the single lens and with three multiplexed lenses. The experimental results confirm that the multiplexed lenses produce a high increase in the depth of focus.

  10. Research on Internal Connection Between Frequency Modulation and Phase Modulation in the Nonlinear Modulation%非线性调制中调频和调相内在联系的研究

    Institute of Scientific and Technical Information of China (English)

    陈皓; 桂伟

    2014-01-01

    从定义和角频率两个角度分析调相,同时从定义和相角两个角度分析调频。进而用数学公式对直接调相和利用调频间接调相、直接调频和利用调相间接调频进行比较,再定量的对调频和调相信号进行比较,从而阐述了调频与调相之间内在的联系。%The paper analyses phase modulation from two angles of definition and angular frequency,and analyses frequency modulation from two angles of definition and phase angle. And then uses a mathematical formula for the comparation between direct phase modulation and indirect phase modulation by frequency,for the comparation between direct frequency modulation and indirect frequency modulation by phase,and then the quantitative comparison of frequency modulation and phase modulation. Then elaborates the nternal connection between FM and PM.

  11. Bunch stabilization using rf phase modulation in the Intense Pulse Neutron Source (IPNS) Rapid Cycling Synchrotron (RCS).

    Energy Technology Data Exchange (ETDEWEB)

    Brumwell, F. R.; Dooling, J. C.; McMichael, G. E.

    1999-09-01

    Phase modulation (PM) is used to increase the current limit in the IPNS RCS. A device referred to as a scrambler introduces a small oscillating phase between the two RCS rf cavities at approximately twice the synchrotrons frequency, f{sub s}. The modulation introduced by the scrambler generates longitudinal oscillations in the bunch at 2f{sub s}. Modulations in the bunch are also observed transversely indicating a coupling between longitudinal and transverse motion. Comparing PM with amplitude modulation (AM), coupling to the beam is roughly equivalent at 2f{sub s}.

  12. Spin and wavelength multiplexed nonlinear metasurface holography

    Science.gov (United States)

    Ye, Weimin; Zeuner, Franziska; Li, Xin; Reineke, Bernhard; He, Shan; Qiu, Cheng-Wei; Liu, Juan; Wang, Yongtian; Zhang, Shuang; Zentgraf, Thomas

    2016-06-01

    Metasurfaces, as the ultrathin version of metamaterials, have caught growing attention due to their superior capability in controlling the phase, amplitude and polarization states of light. Among various types of metasurfaces, geometric metasurface that encodes a geometric or Pancharatnam-Berry phase into the orientation angle of the constituent meta-atoms has shown great potential in controlling light in both linear and nonlinear optical regimes. The robust and dispersionless nature of the geometric phase simplifies the wave manipulation tremendously. Benefitting from the continuous phase control, metasurface holography has exhibited advantages over conventional depth controlled holography with discretized phase levels. Here we report on spin and wavelength multiplexed nonlinear metasurface holography, which allows construction of multiple target holographic images carried independently by the fundamental and harmonic generation waves of different spins. The nonlinear holograms provide independent, nondispersive and crosstalk-free post-selective channels for holographic multiplexing and multidimensional optical data storages, anti-counterfeiting, and optical encryption.

  13. Wavelength conversion, time demultiplexing and multicasting based on cross-phase modulation and four-wave mixing in dispersion-flattened highly nonlinear photonic crystal fiber

    Science.gov (United States)

    Hui, Zhan-Qiang; Zhang, Jian-Guo

    2012-05-01

    We propose the use of cross-phase modulation (XPM) and four-wave mixing (FWM) in dispersion-flattened highly nonlinear photonic crystal fibers (HNL-PCFs) to implement the functionalities of wavelength conversion, simultaneous time demultiplexing and wavelength multicasting in optical time-division multiplexing (OTDM) systems. The experiments on wavelength conversion at 80 Gbit s-1and OTDM demultiplexing from 80 to 10 Gbit s-1 with wavelength multicasting of two channels are successfully demonstrated to validate the proposed scheme, which are carried out by using two segments of dispersion-flattened HNL-PCFs with lengths of 100 and 50 m, respectively. Moreover, the bit error rate (BER) performance is also measured. The results show that our designed system can achieve a power penalty of less than 4.6 dB for two multicasting channels with a 24 nm wavelength span at the BER of 10-9 when compared with the 10 Gbit/s back-to-back measurement. The proposed system is transparent to bit rate since only an ultrafast third-order nonlinear effect is used. The resulting configuration is compact, robust and reliable, benefiting from the use of dispersion-flattened HNL-PCFs with short lengths. This also makes the proposed system more flexible in the operational wavelengths than those based on dispersion-shifted fibers and traditional highly nonlinear fibers. The work was supported in part by the CAS/SAFEA International Partnership Program for Creative Research Teams.

  14. Chapter 5: Modulation Excitation Spectroscopy with Phase-Sensitive Detection for Surface Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Shulda, Sarah; Richards, Ryan M.

    2016-02-19

    Advancements in in situ spectroscopic techniques have led to significant progress being made in elucidating heterogeneous reaction mechanisms. The potential of these progressive methods is often limited only by the complexity of the system and noise in the data. Short-lived intermediates can be challenging, if not impossible, to identify with conventional spectra analysis means. Often equally difficult is separating signals that arise from active and inactive species. Modulation excitation spectroscopy combined with phase-sensitive detection analysis is a powerful tool for removing noise from the data while simultaneously revealing the underlying kinetics of the reaction. A stimulus is applied at a constant frequency to the reaction system, for example, a reactant cycled with an inert phase. Through mathematical manipulation of the data, any signal contributing to the overall spectra but not oscillating with the same frequency as the stimulus will be dampened or removed. With phase-sensitive detection, signals oscillating with the stimulus frequency but with various lag times are amplified providing valuable kinetic information. In this chapter, some examples are provided from the literature that have successfully used modulation excitation spectroscopy with phase-sensitive detection to uncover previously unobserved reaction intermediates and kinetics. Examples from a broad range of spectroscopic methods are included to provide perspective to the reader.

  15. Nanoscale phase engineering of thermal transport with a Josephson heat modulator

    Science.gov (United States)

    Fornieri, Antonio; Blanc, Christophe; Bosisio, Riccardo; D'Ambrosio, Sophie; Giazotto, Francesco

    2016-03-01

    Macroscopic quantum phase coherence has one of its pivotal expressions in the Josephson effect, which manifests itself both in charge and energy transport. The ability to master the amount of heat transferred through two tunnel-coupled superconductors by tuning their phase difference is the core of coherent caloritronics, and is expected to be a key tool in a number of nanoscience fields, including solid-state cooling, thermal isolation, radiation detection, quantum information and thermal logic. Here, we show the realization of the first balanced Josephson heat modulator designed to offer full control at the nanoscale over the phase-coherent component of thermal currents. Our device provides magnetic-flux-dependent temperature modulations up to 40 mK in amplitude with a maximum of the flux-to-temperature transfer coefficient reaching 200 mK per flux quantum at a bath temperature of 25 mK. Foremost, it demonstrates the exact correspondence in the phase engineering of charge and heat currents, breaking ground for advanced caloritronic nanodevices such as thermal splitters, heat pumps and time-dependent electronic engines.

  16. PS-Module prototypes with MPA-light readout chip for the CMS Tracker Phase 2 Upgrade

    CERN Document Server

    Grossmann, Johannes

    2016-01-01

    During the HL-LHC era an instantaneous luminosity of $5\\times10^{34}\\,\\mathrm{cm}^{-2}\\mathrm{s}^{-1}$ will be reached and possibly $3000\\mskip3mu\\mathrm{fb} ^{-1}$ integrated luminosity will be delivered. This results in the requirement for a major upgrade of the CMS Outer Tracker detector. This contribution briefly reviews the module types and the front end readout electronics foreseen in the preparation program known as phase 2 upgrade. R\\&D towards the construction of full module prototypes for the Pixel-Strip (PS) module is ongoing. The module combines a macro-pixel sensor and a strip sensor and has $p_{\\mathrm{T}}\\,$-discrimination capability at module level. The current experience from module construction with a demonstrator assembly and initial laboratory testing with an alternative module concept for the PS-module is shown. A possible calibration method is introduced.

  17. PS-module prototypes with MPA-light readout chip for the CMS Tracker Phase 2 Upgrade

    Science.gov (United States)

    Grossmann, J.

    2017-02-01

    During the HL-LHC era an instantaneous luminosity of 5×1034 cm‑2s‑1 will be reached and possibly 3000 fb‑1 integrated luminosity will be delivered. This results in the requirement for a major upgrade of the CMS Outer Tracker detector. This contribution briefly reviews the module types and the front end readout electronics foreseen in the preparation program known as phase 2 upgrade. R&D towards the construction of full module prototypes for the Pixel-Strip (PS) module is ongoing. The module combines a macro-pixel sensor and a strip sensor and has pT -discrimination capability at module level. The current experience from module construction with a demonstrator assembly and initial laboratory testing with an alternative module concept for the PS-module is shown. A possible calibration method is introduced.

  18. Modulation Format Independent Joint Polarization and Phase Tracking for Coherent Receivers

    CERN Document Server

    Czegledi, Cristian B; Karlsson, Magnus; Johannisson, Pontus

    2016-01-01

    The state of polarization and the carrier phase drift dynamically during transmission in a random fashion in coherent optical fiber communications. The typical digital signal processing solution to mitigate these impairments consists of two separate blocks that track each phenomenon independently. Such algorithms have been developed without taking into account mathematical models describing the impairments. We study a blind, model-based tracking algorithm to compensate for these impairments. The algorithm dynamically recovers the carrier phase and state of polarization jointly for an arbitrary modulation format. Simulation results show the effectiveness of the proposed algorithm, having a fast convergence rate and an excellent tolerance to phase noise and dynamic drift of the polarization. The computational complexity of the algorithm is lower compared to state-of-the-art algorithms at similar or better performance, which makes it a strong candidate for future optical systems.

  19. Ferrimagnetic and Long Period Antiferromagnetic Phases in High Spin Heisenberg Chains with D-Modulation

    Science.gov (United States)

    Hida, Kazuo

    2007-02-01

    The ground state properties of the high spin Heisenberg chains with alternating single site anisotropy are investigated by means of the numerical exact daigonaization and DMRG method. It is found that the ferrimagnetic state appears between the Haldane phase and period doubled Néel phase for the integer spin chains. On the other hand, the transition from the Tomonaga-Luttinger liquid state into the ferrimagnetic state takes place for the half-odd-integer spin chains. In the ferrimagnetic phase, the spontaneous magnetization varies continuously with the modulation amplitude of the single site anisotropy. Eventually, the magnetization is locked to fractional values of the saturated magnetization. These fractional values satisfy the Oshikawa-Yamanaka-Affleck condition. The local spin profile is calculated to reveal the physical nature of each state. In contrast to the case of frustration induced ferrimagnetism, no incommensurate magnetic superstructure is found.

  20. Digital front-end module (DFEM) series; Digital front end module (DFEM) series

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The digital front-end module (DFEM) is a module in which the processes ranging from the reception of digitally modulated radiofrequencies to the output of digital IF (Intermediate Frequency) signals or data streams are integrated. Beginning with a module for the MCNS (Multimedia Cable Network System) cable modem which was the first module in this business field approved by the Cable Labs, U.S., Toshiba has developed a series of DFEMs for various digital media for satellites, ground waves, and CATV (Cable Television) systems. The series is characterized by (1) the serialization of DFEMs compatible with various digital modulation techniques such as 8 PSK (Phase Shift Keying), OFDM (Orthogonal Frequency Division Multiplexing), and 256 QAM (Quadrature Amplitude Modulation), (2) easy connection with digital circuits thanks to the high shielding effect, and (3) the achievement of smaller size, higher performance, and lower power consumption. (translated by NEDO)

  1. Adaptive Bessel-autocorrelation of ultrashort pulses with phase-only spatial light modulators

    Science.gov (United States)

    Huferath-von Luepke, Silke; Bock, Martin; Grunwald, Ruediger

    2009-06-01

    Recently, we proposed a new approach of a noncollinear correlation technique for ultrashort-pulsed coherent optical signals which was referred to as Bessel-autocorrelator (BAC). The BAC-principle combines the advantages of Bessellike nondiffracting beams like stable propagation, angular robustness and self-reconstruction with the principle of temporal autocorrelation. In comparison to other phase-sensitive measuring techniques, autocorrelation is most straightforward and time-effective because of non-iterative data processing. The analysis of nonlinearly converted fringe patterns of pulsed Bessel-like beams reveals their temporal signature from details of fringe envelopes. By splitting the beams with axicon arrays into multiple sub-beams, transversal resolution is approximated. Here we report on adaptive implementations of BACs with improved phase resolution realized by phase-only liquid-crystal-on-silicon spatial light modulators (LCoS-SLMs). Programming microaxicon phase functions in gray value maps enables for a flexible variation of phase and geometry. Experiments on the diagnostics of few-cycle pulses emitted by a mode-locked Ti:sapphire laser oscillator at wavelengths around 800 nm with 2D-BAC and angular tuned BAC were performed. All-optical phase shift BAC and fringe free BAC approaches are discussed.

  2. Non-photic modulation of phase shifts to long light pulses.

    Science.gov (United States)

    Antle, Michael C; Sterniczuk, Roxanne; Smith, Victoria M; Hagel, Kimberly

    2007-12-01

    Circadian rhythms can be reset by both photic and non-photic stimuli. Recent studies have used long light exposure to produce photic phase shifts or to enhance non-photic phase shifts. The presence or absence of light can also influence the expression of locomotor rhythms through masking; light during the night attenuates locomotor activity, while darkness during the day induces locomotor activity in nocturnal animals. Given this dual role of light, the current study was designed to examine the relative contributions of photic and non-photic components present in a long light pulse paradigm. Mice entrained to a light/dark cycle were exposed to light pulses of various durations (0, 3, 6, 9, or 12 h) starting at the time of lights-off. After the light exposure, animals were placed in DD and were either left undisturbed in their home cages or had their wheels locked for the remainder of the subjective night and subsequent subjective day. Light treatments of 6, 9, and 12 h produced large phase delays. These treatments were associated with decreased activity during the nocturnal light and increased activity during the initial hours of darkness following light exposure. When the wheels were locked to prevent high-amplitude activity, the resulting phase delays to the light were significantly attenuated, suggesting that the activity following the light exposure may have contributed to the overall phase shift. In a second experiment, telemetry probes were used to assess what effect permanently locking the wheels had on the phase shift to the long light pulses. These animals had phase shifts fully as large as animals without any form of wheel lock, suggesting that while non-photic events can modulate photic phase shifts, they do not play a role in the full phase-shift response observed in animals exposed to long light pulses. This paradigm will facilitate investigations into non-photic responses of the mouse circadian system.

  3. Spindle error motion measurement using concentric circle grating and phase modulation interferometers

    Science.gov (United States)

    Aketagawa, M.; Madden, M.; Uesugi, S.; Kumagai, T.; Maeda, Y.; Okuyama, E.

    2012-11-01

    In the conventional methods to measure radial, axial and angular motions of spindles, complicated artifacts with relative large volume (such as two balls linked with a cylinder) are required. Small volume artifact is favorable from the viewpoint of the accurate and practical measurement of the spindle motion. This paper describes a concurrent measurement of spindle radial, axial and angular motions using concentric circle grating and phase modulation interferometers. In the measurement, the concentric circle grating with fine pitch is installed on top of the spindle of interest. The grating is a reference artifact in the method. Three optical sensors are fixed over the concentric circle grating, and observe the proper positions of the grating. The optical sensor consists of a frequency modulated laser diode as a light source, and two interferometers. One interferometer observes an interference fringe between reflected light form a fixed mirror and 0-th order diffraction light from the grating to measure the axial motion. Another interferometer observes an interference fringe between +/-2nd diffraction lights from the grating to measure the radial motion. Using three optical sensors, three radial displacements and three axial displacements of the proper observed position of the grating can be measured. From these measured displacements, radial, axial and angular motions of the spindle can be calculated concurrently. In the paper, a measurement instrument, a novel fringe interpolation technique by sinusoidal phase modulation and experimental results are discussed.

  4. Phase-locked modulation delay between the poles of pulsar B1055-52

    CERN Document Server

    Weltevrede, Patrick; Johnston, Simon

    2012-01-01

    We present a detailed single pulse study of PSR B1055-52 based on observations at the Parkes radio telescope. The radio emission is found to have a complex modulation dominated by a periodicity of ~20 times its rotational period P (0.197s), whose phase and strength depends on pulse longitude. This periodicity exhibits a phase-locked delay of about 2.5P between the main pulse (MP) and interpulse (IP), presumed to be the opposite poles of the pulsar. This delay corresponds to a light travel distance of many times the light cylinder radius. More complex modulations are found within the MP on timescales down to about 9P, and both these and the principal modulation vary strongly across the (at least) 7 components which the MP and IP exhibit. The nature of the single pulse emission, which ranges from smooth and longitudinally extended to `spiky', is also component-dependent. Despite these disparities, the total pulse intensity distributions at the MP and IP are virtually identical in shape, suggesting a common emis...

  5. Control strategy for Single-phase Transformerless Three-leg Unified Power Quality Conditioner Based on Space Vector Modulation

    DEFF Research Database (Denmark)

    Lu, Yong; Xiao, Guochun; Wang, Xiongfei

    2016-01-01

    The unified power quality conditioner (UPQC) is known as an effective compensation device to improve PQ for sensitive end-users. This paper investigates the operation and control of a single-phase three-leg UPQC (TL-UPQC), where a novel space vector modulation method is proposed for naturally...... solving the coupling problem introduced by the common switching leg. The modulation method is similar to the well-known space vector modulation widely used with three-phase voltage source converters, which thus brings extra flexibility to the TL-UPQC system. Two optimized modulation modes with either...... reduced switching loss or harmonic distortion are derived, evaluated, and discussed, in order to demonstrate the flexibility brought by the space vector modulated TL-UPQC. Simulations and experimental results are presented to verify the feasibility and effectiveness of the proposed space vector modulation...

  6. Chromatic Dispersion Monitoring Method Based on Phase Shift Technique

    Institute of Scientific and Technical Information of China (English)

    L(U) Chengang; WU Xing; ZENG Lizhu; QIN Yifan; ZU Peng; HU Zhixiong; GE Chunfeng

    2007-01-01

    The modulation phase shift method was used to measure chromatic dispersion in a standard single mode fiber for telecommunication. The modulation phase difference of the transmitted light at the wavelength of 1 532. 16 nm modulated by a radio frequency signal was measured, relative to the transmitted light at the wavelength of 1 549.33 nm modulated by the same signal. By introducing a reference light at the wavelength of 1 310 nm, a 1 310/1 550 nm wavelength division multiplexing was used instead of the high cost dense wavelength division multiplexing. In the experiment, two testing lights were coupled with the reference light to the fiber spools of different lengths, respectively. By finite difference method, the chromatic dispersion between the two testing lights was measured, and the fixed errors generated during transmission were less than 0.5 ps/(nm·km).

  7. Optical free-space wavelength-division-multiplexing transport system.

    Science.gov (United States)

    Lin, Chun-Yu; Lin, Ying-Pyng; Lu, Hai-Han; Chen, Chia-Yi; Jhang, Tai-Wei; Chen, Min-Chou

    2014-01-15

    An optical free-space wavelength-division-multiplexing (WDM) transport system employing vertical cavity surface emitting lasers and spatial light modulators with 16-quadrature amplitude modulation orthogonal frequency-division multiplexing modulating signals over a 17.5 m free-space link is proposed and demonstrated. With the help of a low-noise amplifier and data comparator, good bit error rate performance is obtained for each optical channel. Such an optical free-space WDM transport system would be attractive for providing services including data and telecommunication services.

  8. High dynamic range low noise amplifier and wideband hybrid phase shifter for SiGe BiCMOS phased array T/R modules

    OpenAIRE

    2014-01-01

    Transmit/Receive Module (T/R Module) is one of the most essential blocks for Phased Array Radio Detection and Ranging (RADAR) system; due to being very influential on system level performance. To achieve high performance specifications, T/R Module structures are constructed with using III-V devices, which has some significant disadvantages; they are costly, and also consume too much area and power. As a result, application area of T/R Module is mainly restricted with the military and dedicate...

  9. Optimization of the sinusoidal phase modulation technique in resonant fiber optic gyro

    Science.gov (United States)

    Wang, Linglan; Li, Hanzhao; Zhang, Jianjie; Ma, Huilian; Jin, Zhonghe

    2017-03-01

    The sinusoidal wave phase modulation and demodulation have been widely used in the signal processing system of the resonant fiber optic gyro (RFOG). An appropriate selection of the modulation frequency is of great importance, for the frequency value directly affects the slope of the demodulation curve at the resonance point which carries the gyro output information. A large demodulation slope is pursued in a high-performance RFOG. In this paper, an analytical expression of the demodulation slope is for the first time deduced in both transmission-type and reflection-type fiber ring resonators without any approximation. The relationship between the slope value and the modulation frequency at the resonance point is accurately calculated. The calculated best modulation frequency maximizing the demodulation slope at the resonance point is different from previous widely used optimal frequency given by the Lorentzian approximation method. More importantly, both theoretical and experimental results indicate that the achieved maximal demodulation slope from the proposed analytical expression method is double of that obtaining from the Lorentzian approximation method.

  10. Laser beam shaping limitations for laboratory simulation of turbulence using a phase-only spatial light modulator

    CSIR Research Space (South Africa)

    Litvin, IA

    2007-09-01

    Full Text Available Recent approaches to demonstrating adaptive optics and atmospheric turbulence have made use of spatial light modulators (SLMs) as the active phase element. However, there are limitations in using SLMs as an accurate method of simulating turbulence...

  11. Effective nonlinearities and multi-wavelength second-harmonic generation in modulated quasi-phase-matching gratings

    DEFF Research Database (Denmark)

    Bang, Ole; Graversen, T. W.; Clausen, Carl A. Balslev

    2000-01-01

    Quasi-phase-matching gratings induces Kerr effects in quadratic nonlinear materials. We show analytically and confirm numerically how modulating the grating changes the effective quadratic and cubic nonlinearities and allows for multi-wavelength second-harmonic generation....

  12. Cross-phase modulational instability in an elliptical birefringent fiber with higher order nonlinearity and dispersion

    Indian Academy of Sciences (India)

    R Ganapathy; V C Kuriakose

    2002-04-01

    We obtain conditions for the occurrence of cross-phase modulational instability in the normal dispersion regime for the coupled higher order nonlinear Schrödinger equation with higher order dispersion and nonlinear terms.

  13. Multidiameter optical ring and Hermite-Gaussian vortices for wavelength division multiplexing-mode division multiplexing

    Science.gov (United States)

    Amphawan, Angela; Fazea, Yousef

    2016-10-01

    Optical vortices are high-capacity data carriers for mode division multiplexing (MDM) in multimode fiber (MMF). This paper reports on the MDM of a combination of helical-phased optical vortices comprising donut modes and Hermite-Gaussian (HG) modes for different radial offsets from the MMF axis. A data rate of 44 Gbps is achieved for wavelength division multiplexing-MDM of two pairs of helical-phased donut mode and HG mode at wavelengths 1550.12 and 1551.72 nm for a MMF length of 1500 m.

  14. Experimental Demonstration of Nonlinear Frequency Division Multiplexed Transmission

    CERN Document Server

    Aref, Vahid; Schuh, Karsten; Idler, Wilfried

    2015-01-01

    We experimentally demonstrate an NFDM optical system with modulation over nonlinear discrete spectrum. Particularly, each symbol carries 4-bits from multiplexing two eigenvalues modulated by QPSK constellation. We show a low error performance using NFT detection with 4Gbps rate over 640km.

  15. Analysis of the Crosstalk in WDM Systems Caused by Cross-phase Modulation in Erbium-doped Fiber Amplifiers

    Institute of Scientific and Technical Information of China (English)

    LIU Ning; LIAO Changjun; LIU Songhao; GUO Qi; XU Wengchen

    2001-01-01

    The crosstalk in WDM systems caused by cross-phase modulation (XPM) in erbium-doped fiber amplifiers(EDFA) was studied analytically. The results confirm that the EDFA induced phase shift does cause crosstalk in WDM systems. The crosstalk between two channels both with modulated pulse signals is studied for the first time. It was found that the EDFA induced phase shift will cause serious deterioration of the eye diagram when the optical signals continue to travel in the normal-dispersion regime of the transmission fiber, while in the anomalous-dispersion regime this phase shift will not cause much deterioration of the eye diagram.

  16. Ionization-induced asymmetric self-phase modulation and universal modulational instability in gas-filled hollow-core photonic crystal fibers

    CERN Document Server

    Saleh, Mohammed F; Travers, John C; Russell, Philip St J; Biancalana, Fabio

    2012-01-01

    We study theoretically the propagation of relatively long pulses with ionizing intensities in a hollow-core photonic crystal fiber filled with a Raman-inactive gas. Due to photoionization, previously unknown types of asymmetric self-phase modulation and `universal' modulational instabilities existing in both normal and anomalous dispersion regions appear. We also show that it is possible to spontaneously generate a plasma-induced continuum of blueshifting solitons, opening up new possibilities for pushing supercontinuum generation towards shorter and shorter wavelengths.

  17. Theoretical study on coupling effects of modulation depth between two photorefractive phase gratings with an external applied field

    Institute of Scientific and Technical Information of China (English)

    YUAN Baohong; ZHOU Zhongxiang; HOU Chunfeng; SUN Xiudong

    2001-01-01

    We used the perturbation expanding method to the hopping model and studied coupling effects of the modulation depth between two photorefractive phase gratings stored in one point with an external applied DC electric field . It has been found that the modulation depth of one of the two gratings seriously affects the spatial-charge field of the other grating.

  18. Characterisation and efficient simulation of thermal phenomena in SIMOX thermo-optic phase modulators

    CERN Document Server

    Clark, S A

    2001-01-01

    device has been designed to minimize power requirements, 3dB bandwidths in excess of 1kHz have been achieved for less than 10mW of drive power. A basic set of design parameters is developed which allow estimation of bandwidth and power requirements based on an initial knowledge of the material system and the intended modulator architecture. Silicon can be very effectively exploited in integrated optics due to its well-defined process chemistry and the availability of techniques developed primarily for the semiconductor industry which allow control over dimensions and the creation of arbitrary two dimensional structures with great precision and repeatability. In this thesis the complete design and simulation of thermo-optic phase modulators, realised in silicon-on-insulator (SOI), is presented. Since material thermal and optical parameters vary with temperature, anomalous departure between first-order theory and experimentation can exist when operating under conditions whereby material parameters are markedly ...

  19. Current Status of the Pixel Phase I Upgrade in CMS: Barrel Module Production

    CERN Document Server

    Bartek, Rachel

    2015-01-01

    The silicon pixel detector is the innermost component of the CMS tracking system, providing high precision space point measurements of charged particle trajectories. Before 2018 the instantaneous luminosity of the LHC is expected to reach about 2~x~$10^{34}~\\rm{cm}^{-2}\\rm{s}^{-1}$, which will significantly increase the number of interactions per bunch crossing. To maintain a high tracking efficiency, CMS has planned to replace the current pixel system during phase I by a new lightweight detector, equipped with an additional 4th layer in the barrel, and one additional forward/backward disk. The present status of barrel modules production will be presented, including preliminary results from tests on the first production pixel modules of the new pixel tracker.

  20. Deterministic reshaping of single-photon spectra using cross-phase modulation

    CERN Document Server

    Matsuda, Nobuyuki

    2016-01-01

    The frequency conversion of light has proved to be a crucial technology for communication, spectroscopy, imaging, and signal processing. In the quantum regime, it also offers great potential for realizing quantum networks incorporating disparate physical systems and quantum-enhanced information processing over a large computational space. The frequency conversion of quantum light, such as single photons, has been extensively investigated for the last two decades using all-optical frequency mixing, with the ultimate goal of realizing lossless and noiseless conversion. I demonstrate another route to this target using frequency conversion induced by cross-phase modulation in a dispersion-managed photonic crystal fiber. Owing to the deterministic and all-optical nature of the process, the lossless and low-noise spectral reshaping of a single-photon wave packet in the telecommunication band has been readily achieved with a modulation bandwidth as large as 0.4 THz. I further demonstrate that the scheme is applicabl...

  1. Improved dichotomous search frequency offset estimator for burst-mode continuous phase modulation

    Institute of Scientific and Technical Information of China (English)

    翟文超; 李赞; 司江勃; 柏均

    2015-01-01

    A data-aided technique for carrier frequency offset estimation with continuous phase modulation (CPM) in burst-mode transmission is presented. The proposed technique first exploits a special pilot sequence, or training sequence, to form a sinusoidal waveform. Then, an improved dichotomous search frequency offset estimator is introduced to determine the frequency offset using the sinusoid. Theoretical analysis and simulation results indicate that our estimator is noteworthy in the following aspects. First, the estimator can operate independently of timing recovery. Second, it has relatively low outlier, i.e., the minimum signal-to-noise ratio (SNR) required to guarantee estimation accuracy. Finally, the most important property is that our estimator is complexity-reduced compared to the existing dichotomous search methods: it eliminates the need for fast Fourier transform (FFT) and modulation removal, and exhibits faster convergence rate without accuracy degradation.

  2. On network coding and modulation mapping for three-phase bidirectional relaying

    KAUST Repository

    Chang, Ronald Y.

    2015-12-03

    © 2015 IEEE. In this paper, we consider the network coding (NC) enabled three-phase protocol for information exchange between two users in a wireless two-way (bidirectional) relay network. Modulo-based (nonbinary) and XOR-based (binary) NC schemes are considered as information mixture schemes at the relay while all transmissions adopt pulse amplitude modulation (PAM). We first obtain the optimal constellation mapping at the relay that maximizes the decoding performance at the users for each NC scheme. Then, we compare the two NC schemes, each in conjunction with the optimal constellation mapping at the relay, in different conditions. Our results demonstrate that, in the low SNR regime, binary NC outperforms nonbinary NC with 4-PAM, while they have mixed performance with 8-PAM. This observation applies to quadrature amplitude modulation (QAM) composed of two parallel PAMs.

  3. Broadband photonic microwave phase shifter based on controlling two RF modulation sidebands via a Fourier-domain optical processor.

    Science.gov (United States)

    Yang, J; Chan, E H W; Wang, X; Feng, X; Guan, B

    2015-05-04

    An all-optical photonic microwave phase shifter that can realize a continuous 360° phase shift over a wide frequency range is presented. It is based on the new concept of controlling the amplitude and phase of the two RF modulation sidebands via a Fourier-domain optical processor. The operating frequency range of the phase shifter is largely increased compared to the previously reported Fourier-domain optical processor based phase shifter that uses only one RF modulation sideband. This is due to the extension of the lower RF operating frequency by designing the amplitude and phase of one of the RF modulation sidebands while the other sideband is designed to realize the required RF signal phase shift. The two-sideband amplitude-and-phase-control based photonic microwave phase shifter has a simple structure as it only requires a single laser source, a phase modulator, a Fourier-domain optical processor and a single photodetector. Investigation on the bandwidth limitation problem in the conventional Fourier-domain optical processor based phase shifter is presented. Comparisons between the measured phase shifter output RF amplitude and phase responses with theory, which show excellent agreement, are also presented for the first time. Experimental results demonstrate the full -180° to + 180° phase shift with little RF signal amplitude variation of less than 3 dB and with a phase deviation of less than 4° over a 7.5 GHz to 26.5 GHz frequency range, and the phase shifter exhibits a long term stable performance.

  4. Ultrafast optical phase modulation with metallic nanoparticles in ion-implanted bilayer silica

    Energy Technology Data Exchange (ETDEWEB)

    Torres-Torres, C [Seccion de Estudios de Posgrado e Investigacion, ESIME-Z, Instituto Politecnico Nacional, Mexico, DF, 07738 (Mexico); Tamayo-Rivera, L; Silva-Pereyra, H G; Reyes-Esqueda, J A; Rodriguez-Fernandez, L; Crespo-Sosa, A; Cheang-Wong, J C; Oliver, A [Instituto de Fisica, Universidad Nacional Autonoma de Mexico, 04510, Mexico, DF (Mexico); Rangel-Rojo, R [Departamento de Optica, Centro de Investigacion Cientifica y de Educacion Superior de Ensenada Apartado Postal 360, Ensenada, BC, 22860 (Mexico); Torres-Martinez, R, E-mail: crstorres@yahoo.com.mx [Centro de Investigacion en Ciencia Aplicada y TecnologIa Avanzada Unidad Queretaro, Instituto Politecnico Nacional, Santiago de Queretaro, Queretaro, 76090 (Mexico)

    2011-09-02

    The nonlinear optical response of metallic-nanoparticle-containing composites was studied with picosecond and femtosecond pulses. Two different types of nanocomposites were prepared by an ion-implantation process, one containing Au nanoparticles (NPs) and the other Ag NPs. In order to measure the optical nonlinearities, we used a picosecond self-diffraction experiment and the femtosecond time-resolved optical Kerr gate technique. In both cases, electronic polarization and saturated absorption were identified as the physical mechanisms responsible for the picosecond third-order nonlinear response for a near-resonant 532 nm excitation. In contrast, a purely electronic nonlinearity was detected at 830 nm with non-resonant 80 fs pulses. Regarding the nonlinear optical refractive behavior, the Au nanocomposite presented a self-defocusing effect, while the Ag one presented the opposite, that is, a self-focusing response. But, when evaluating the simultaneous contributions when the samples are tested as a multilayer sample (silica-Au NPs-silica-Ag NPs-silica), we were able to obtain optical phase modulation of ultra-short laser pulses, as a result of a significant optical Kerr effect present in these nanocomposites. This allowed us to implement an ultrafast all-optical phase modulator device by using a combination of two different metallic ion-implanted silica samples. This control of the optical phase is a consequence of the separate excitation of the nonlinear refracting phenomena exhibited by the separate Au and Ag nanocomposites.

  5. Threshold-voltage modulated phase change heterojunction for application of high density memory

    Energy Technology Data Exchange (ETDEWEB)

    Yan, Baihan; Tong, Hao, E-mail: tonghao@hust.edu.cn; Qian, Hang; Miao, Xiangshui [Wuhan National Laboratory for Optoelectronics, Huazhong University of Science and Technology, Wuhan 430074 (China); School of Optical and Electronic Information, Huazhong University of Science and Technology, Wuhan 430074 (China)

    2015-09-28

    Phase change random access memory is one of the most important candidates for the next generation non-volatile memory technology. However, the ability to reduce its memory size is compromised by the fundamental limitations inherent in the CMOS technology. While 0T1R configuration without any additional access transistor shows great advantages in improving the storage density, the leakage current and small operation window limit its application in large-scale arrays. In this work, phase change heterojunction based on GeTe and n-Si is fabricated to address those problems. The relationship between threshold voltage and doping concentration is investigated, and energy band diagrams and X-ray photoelectron spectroscopy measurements are provided to explain the results. The threshold voltage is modulated to provide a large operational window based on this relationship. The switching performance of the heterojunction is also tested, showing a good reverse characteristic, which could effectively decrease the leakage current. Furthermore, a reliable read-write-erase function is achieved during the tests. Phase change heterojunction is proposed for high-density memory, showing some notable advantages, such as modulated threshold voltage, large operational window, and low leakage current.

  6. 40 Gbit/s serial data signal regeneration using self-phase modulation in a silicon nanowire

    DEFF Research Database (Denmark)

    Ji, Hua; Wang, Ju; Hu, Hao

    2012-01-01

    We experimentally demonstrate self-phase modulation based all-optical regeneration of a 40 Gbit/s serial data signal in a silicon nanowire. Bit error rate characterization shows 2 dB receiver power improvement.......We experimentally demonstrate self-phase modulation based all-optical regeneration of a 40 Gbit/s serial data signal in a silicon nanowire. Bit error rate characterization shows 2 dB receiver power improvement....

  7. Phase-dependent modulation as a novel approach for therapeutic brain stimulation

    Directory of Open Access Journals (Sweden)

    Ramin eAzodi-Avval

    2015-02-01

    Full Text Available Closed-loop paradigms provide us with the opportunity to optimize stimulation protocols for perturbation of pathological oscillatory activity in brain-related disorders. In this vein, spiking activity of motor cortex neurons and beta activity of local field potentials in the subthalamic nucleus have both been used independently of each other as neuronal signals to trigger deep brain stimulation for alleviating Parkinsonism. These approaches were superior to the standard continuous high-frequency stimulation protocols used in daily practice. However, they achieved their effects by bursts of stimulation that were applied at high-frequency as well, i.e. independent of the phase information in the stimulated region. In this context, we propose that, by timing stimulation pulses relative to the ongoing oscillation, an alternative approach, namely the targeted perturbation of pathological rhythms, could be obtained.In this modeling study, we first captured the underlying dynamics of neuronal oscillations in the human subthalamic nucleus by phased coupled neuronal oscillators. We then quantified the nature of the interaction between these coupled oscillators by obtaining a physiologically informed phase response curve from local field potentials. Reconstruction of the phase response curve predicted the sensitivity of the phase oscillator to external stimuli, revealing phase intervals that optimally maximized the degree of perturbation. We conclude that our specifically timed intervention based on the coupled oscillator concept will enable us to identify personalized ways of delivering stimulation pulses in closed-loop paradigms triggered by the phase of pathological oscillations. This will pave the way for novel physiological insights and substantial clinical benefits. In addition, this precisely phased modulation may be capable of modifying the effective interactions between oscillators in an entirely new manner.

  8. Analytical bit error rate performance evaluation of an orthogonal frequency division multiplexing power line communication system impaired by impulsive and Gaussian channel noise

    OpenAIRE

    Munshi Mahbubur Rahman; Satya Prasad Majumder

    2015-01-01

    An analytical approach is presented to evaluate the bit error rate (BER) performance of a power line (PL) communication system considering the combined influence of impulsive noise and background PL Gaussian noise. Middleton class-A noise model is considered to evaluate the effect of impulsive noise. The analysis is carried out to find the expression of the signal-to-noise ratio and BER considering orthogonal frequency division multiplexing (OFDM) with binary phase shift keying modulation wit...

  9. Modulated Phase of a Potts Model with Competing Binary Interactions on a Cayley Tree

    Science.gov (United States)

    Ganikhodjaev, N.; Temir, S.; Akin, H.

    2009-11-01

    We study the phase diagram for Potts model on a Cayley tree with competing nearest-neighbor interactions J 1, prolonged next-nearest-neighbor interactions J p and one-level next-nearest-neighbor interactions J o . Vannimenus proved that the phase diagram of Ising model with J o =0 contains a modulated phase, as found for similar models on periodic lattices, but the multicritical Lifshitz point is at zero temperature. Later Mariz et al. generalized this result for Ising model with J o ≠0 and recently Ganikhodjaev et al. proved similar result for the three-state Potts model with J o =0. We consider Potts model with J o ≠0 and show that for some values of J o the multicritical Lifshitz point be at non-zero temperature. We also prove that as soon as the same-level interaction J o is nonzero, the paramagnetic phase found at high temperatures for J o =0 disappears, while Ising model does not obtain such property. To perform this study, an iterative scheme similar to that appearing in real space renormalization group frameworks is established; it recovers, as particular case, previous work by Ganikhodjaev et al. for J o =0. At vanishing temperature, the phase diagram is fully determined for all values and signs of J 1, J p and J o . At finite temperatures several interesting features are exhibited for typical values of J o / J 1.

  10. SERIALLY CONCATENATED CONTINUOUS PHASE MODULATION WITH REDUCED ITERATIVE DEMODULATION AND DETECTION

    Institute of Scientific and Technical Information of China (English)

    Sun Jinhua; Li Jiandong; Jin Lijun

    2007-01-01

    A reduced state Soft Input Soft Output (SISO) a posteriori probability algorithm for Serially Concatenated Continuous Phase Modulation (SCCPM) is proposed in this paper. Based on the Reduced State Sequence Detection (RSSD), it has more general form compared with other reduced state SISO algorithms. The proposed algorithm can greatly reduce the state number, thus leads to the computation complexity reduction. It also minimizes the degradation in Euclidean distance with decision feedback in the reduced state trellis. Analysis and simulation results show that the performance degradation is little with proper reduction scheme.

  11. A reduced state SISO iterative decoding algorithm for serially concatenated continuous phase modulation

    Institute of Scientific and Technical Information of China (English)

    SUN JinHua; LI JianDong; JIN LiJun

    2007-01-01

    In this paper, serially concatenated continuous phase modulation (SCCPM) system is analyzed and a reduced state soft input soft output (SISO) a posteriori probability algorithm is proposed. Based on the reduced state sequence detection (RSSD), it has the more general form compared with other reduced state SISO algorithms. The proposed algorithm can greatly reduce the state number, thus leads to the computation complexity reduction. It also minimizes the degradation in Euclidean distance with decision feedback in the reduced state trellis. Analysis and simulation results show that the performance degradation is little with proper reduction scheme.

  12. Detection and characterization of single nanoparticles by interferometric phase modulated ellipsometry

    Energy Technology Data Exchange (ETDEWEB)

    Barroso, F.; Bosch, S.; Tort, N.; Arteaga, O. [Universitat de Barcelona, IN2UB, Dep. Fisica Aplicada i Optica, c/Marti i Franques 1, 08028 (Spain); Sancho-Parramon, J. [Rudjer Boskovic Institute, Bijenicka c. 54, Zagreb 10002 (Croatia); Jover, E.; Bertran, E. [Universitat de Barcelona, IN2UB, Dep. Fisica Aplicada i Optica, c/Marti i Franques 1, 08028 (Spain); Canillas, A., E-mail: acanillas@ub.ed [Universitat de Barcelona, IN2UB, Dep. Fisica Aplicada i Optica, c/Marti i Franques 1, 08028 (Spain)

    2011-02-28

    We introduce a new measurement system called Nanopolar interferometer devoted to monitor and characterize single nanoparticles which is based on the interferometric phase modulated ellipsometry technique. The system collects the backscattered light by the particles in the solid angle subtended by a microscope objective and then analyses its frequency components. The results for the detection of 2 {mu}m and 50 nm particles are explained in terms of a cross polarization effect of the polarization vectors when the beam converts from divergent to parallel in the microscope objective. This explanation is supported with the results of the optical modelling using the exact Mie theory for the light scattered by the particles.

  13. Sensorless Modeling of Varying Pulse Width Modulator Resolutions in Three-Phase Induction Motors

    Science.gov (United States)

    Marko, Matthew David; Shevach, Glenn

    2017-01-01

    A sensorless algorithm was developed to predict rotor speeds in an electric three-phase induction motor. This sensorless model requires a measurement of the stator currents and voltages, and the rotor speed is predicted accurately without any mechanical measurement of the rotor speed. A model of an electric vehicle undergoing acceleration was built, and the sensorless prediction of the simulation rotor speed was determined to be robust even in the presence of fluctuating motor parameters and significant sensor errors. Studies were conducted for varying pulse width modulator resolutions, and the sensorless model was accurate for all resolutions of sinusoidal voltage functions. PMID:28076418

  14. Cross-phase-modulation-induced instability in photonic-crystal fibers.

    Science.gov (United States)

    Serebryannikov, E E; Konorov, S O; Ivanov, A A; Alfimov, M V; Scalora, M; Zheltikov, A M

    2005-08-01

    Cross-phase-modulation-induced instability is identified as a significant mechanism for efficient parametric four-wave-mixing frequency conversion in photonic-crystal fibers. Fundamental-wavelength femtosecond pulses of a Cr, forsterite laser are used in our experiments to transform the spectrum of copropagating second-harmonic pulses of the same laser in a photonic-crystal fiber. Efficient generation of sidebands shifted by more than 80 THz with respect to the central frequency of the second harmonic is observed in the output spectrum of the probe field.

  15. Sinusoidal phase-modulating fiber-optic interferometer fringe with a feedback control system.

    Science.gov (United States)

    Lv, Changrong; Duan, Fajie; Bo, En; Duan, Xiaojie; Feng, Fan; Fu, Xiao

    2014-09-20

    A displacement measurement system using a fiber-optic interferometer fringe projector with a feedback control system is presented and demonstrated. The system utilizes the integrating bucket method to detect the desired phase or the displacement and Fresnel reflection signal to realize measurement of the disturbance and feed it back to the modulated signal of the laser at the same time. The continuous signal truly reflects the error information, as the output light and reflected light share the same optical path. Practical experiments validate the feasibility of this method.

  16. Enhanced soliton-effect pulse compression by cross-phase modulation in optical fibers

    Institute of Scientific and Technical Information of China (English)

    曹文华; 刘颂豪

    2000-01-01

    A new method is proposed to enhance the soliton-effect compression of optical pulses. It consists of copropagating two optical pulses with close wavelengths in the anomalous group-velocity dispersion regime of single-mode fibers. Numerical simulations show that, as compared with the traditional single pulse compression method, cross-phase modulation can not only dramatically increase the compression ratio but also decrease the optimum fiber length. The effects of initial pulse-width mismatch, Raman self-scattering, and pulse walk-off on the pulse compression are also discussed.

  17. Effects of nonlinear phase modulation on quantum frequency conversion using four-wave mixing Bragg scattering

    DEFF Research Database (Denmark)

    Andersen, Lasse Mejling; McKinstrie, C. J.; Rottwitt, Karsten

    2013-01-01

    Recently, we solved the coupled-mode equations for Bragg scattering (BS) in the low- and high-conversion regimes, but without the effects of nonlinear phase modulation (NPM). We now present solutions and Green functions in the low-conversion regime that include NPM. We find that NPM does not change...... are still possible, even when the effects of NPM are included. Finally, the effects of using different input signals are considered, and we conclude that using the natural input modes of the system drastically increases the efficiency. © (2013) COPYRIGHT Society of Photo-Optical Instrumentation Engineers...

  18. Control Strategy for Three Phase Voltage Source PWM Rectifier Based on the Space Vector Modulation

    Directory of Open Access Journals (Sweden)

    MILOUD, Y.

    2010-08-01

    Full Text Available This paper proposes the space vector pulse width modulation (SVPWM control scheme for three-phase voltage source PWM rectifier. The control system based on SVPWM includes two PI controllers which are used to regulate the AC currents and DC-link voltage. The proposed control can stabilize the minimum of the systems storage function at the desired equilibrium point determined by unity power factor and sinusoidal current on the AC side, and constant output voltage on the DC side. So the stable state performance and robustness against the load�s disturbance of PWM rectifiers are both improved. The simulation result shows feasibility of this strategy.

  19. Observation of spectral self-imaging by nonlinear parabolic cross-phase modulation.

    Science.gov (United States)

    Lei, Lei; Huh, Jeonghyun; Cortés, Luis Romero; Maram, Reza; Wetzel, Benjamin; Duchesne, David; Morandotti, Roberto; Azaña, José

    2015-11-15

    We report an experimental demonstration of spectral self-imaging on a periodic frequency comb induced by a nonlinear all-optical process, i.e., parabolic cross-phase modulation in a highly nonlinear fiber. The comb free spectral range is reconfigured by simply tuning the temporal period of the pump parabolic pulse train. In particular, undistorted FSR divisions by factors of 2 and 3 are successfully performed on a 10 GHz frequency comb, realizing new frequency combs with an FSR of 5 and 3.3 GHz, respectively. The pump power requirement associated to the SSI phenomena is also shown to be significantly relaxed by the use of dark parabolic pulses.

  20. Calibration of spatial light modulators suffering from spatially varying phase response.

    Science.gov (United States)

    Engström, David; Persson, Martin; Bengtsson, Jörgen; Goksör, Mattias

    2013-07-01

    We present a method for converting the desired phase values of a hologram to the correct pixel addressing values of a spatial light modulator (SLM), taking into account detailed spatial variations in the phase response of the SLM. In addition to thickness variations in the liquid crystal layer of the SLM, we also show that these variations in phase response can be caused by a non-uniform electric drive scheme in the SLM or by local heating caused by the incident laser beam. We demonstrate that the use of a global look-up table (LUT), even in combination with a spatially varying scale factor, generally does not yield sufficiently accurate conversion for applications requiring highly controllable output fields, such as holographic optical trapping (HOT). We therefore propose a method where the pixel addressing values are given by a three-dimensional polynomial, with two of the variables being the (x, y)-positions of the pixels, and the third their desired phase values. The coefficients of the polynomial are determined by measuring the phase response in 8 × 8 sub-sections of the SLM surface; the degree of the polynomial is optimized so that the polynomial expression nearly replicates the measurement in the measurement points, while still showing a good interpolation behavior in between. The polynomial evaluation increases the total computation time for hologram generation by only a few percent. Compared to conventional phase conversion methods, for an SLM with varying phase response, we found that the proposed method increases the control of the trap intensities in HOT, and efficiently prevents the appearance of strong unwanted 0th order diffraction that commonly occurs in SLM systems.

  1. OCT based on multi-frequency sweeping Fizeau interferometer with phase modulating method

    Science.gov (United States)

    Choi, S.; Watanabe, T.; Sasaki, O.; Suzuki, T.

    2013-09-01

    The Multi-frequency sweeping Fizeau-type interferometer (MFS-FI) for optical coherence tomography (OCT) is demonstrated. The multi-frequency sweeping by a variable Fabry-Perot filter permits detection of high-order low-coherence interferometric signals in the Fizeau interferometer. The sinusoidal phase modulation technique was utilized to detect accurate interference amplitude and phase distributions of back scattered light from surfaces of a sample. OCT measurements by the MFS-FI were conducted for vibrating glass plates with a frequency of 1 kHz, and cellular tissues fixed with formalin and embedded in paraffin. The tomographic 3-dimensional volume and cross-sectional surface displacements were detected with an accuracy of nano-meters.

  2. Acoustic one-way metasurfaces: Asymmetric Phase Modulation of Sound by Subwavelength Layer

    Science.gov (United States)

    Jiang, Xue; Liang, Bin; Zou, Xin-Ye; Yang, Jing; Yin, Lei-Lei; Yang, Jun; Cheng, Jian-Chun

    2016-06-01

    We theoretically design and numerically demonstrate an acoustic one-way metasurface, which is a planar and acoustically subwavelength layer behaving like a nearly-reflectionless surface with arbitrary wave-steering capability for incident wave impinging on one side, while virtually blocking the reversed wave. The underlying mechanism is based on an asymmetric phase modulation by coupling a phase array and a near-zero-index medium. We exemplify a metastructure-based implementation by combining the hybrid metastuctures and labyrinthine structures. Moreover, the performance of the proposed implementation is demonstrated via three distinct phenomena of anomalous refraction, wave splitting and conversion of propagation wave to surface wave. Our findings may offer more possibilities for sound manipulation and improve the application potential of acoustic artificial devices in situations such as ultrasonic imaging and therapy.

  3. First Results with a Fast Phase and Amplitude Modulator for High Power RF Application

    CERN Document Server

    Frischholz, Hans; Valuch, D; Weil, C

    2004-01-01

    In a high energy and high power superconducting proton linac, it is more economical to drive several cavities with a single high power transmitter rather than to use one transmitter per cavity. However, this option has the disadvantage of not permitting individual control for each cavity, which potentially leads to instabilities. Provided that it can be built at a reasonable cost, a fast phase and amplitude modulator inserted into each cavity feeder line can provide the necessary control capability. A prototype of such a device has been built, based on two fast and compact high power RF phase-shifters, magnetically biased by external coils. The design is described, together with the results obtained at high and low power levels.

  4. A Smart Current Modulation Scheme for Harmonic Reduction in Three- Phase Motor Drive Applications

    DEFF Research Database (Denmark)

    Davari, Pooya; Zare, Firuz; Blaabjerg, Frede

    2015-01-01

    harmonic mitigation methods have been developed over the years, the total cost and complexity has become the main obstacle in employing prior-art methods for motor drive systems. This paper presents a novel current modulation method based on the electronic inductor concept for three-phase ac-dc systems......Electric motor-driven systems consume considerable amount of the global electricity. Majority of three-phase motor drives are equipped with conventional diode rectifier and passive harmonic mitigation, being witnessed as the main source in generating input current harmonics. While many active...... to reduce input current harmonics. The obtained results at simulation and experimental levels confirm the effectiveness of the proposed approach....

  5. Preparing arbitrary pure states of spatial qudits with a single phase-only spatial light modulator

    CERN Document Server

    Solís-Prosser, M A; Varga, J J M; Rebón, L; Ledesma, S; Iemmi, C; Neves, L

    2013-01-01

    Spatial qudits are D-dimensional ($D\\geq 2$) quantum systems carrying information encoded in the discretized transverse momentum and position of single photons. We present a proof-of-principle demonstration of a method for preparing arbitrary pure states of such systems by using a single phase-only spatial light modulator (SLM). The method relies on the encoding of the complex transmission function corresponding to a given spatial qudit state onto a preset diffraction order of a phase-only grating function addressed at the SLM. Fidelities of preparation above 94% were obtained with this method, which is simpler, less costly, and more efficient than those that require two SLMs for the same purpose.

  6. Functional Multiplex PageRank

    CERN Document Server

    Iacovacci, Jacopo; Arenas, Alex; Bianconi, Ginestra

    2016-01-01

    Recently it has been recognized that many complex social, technological and biological networks have a multilayer nature and can be described by multiplex networks. Multiplex networks are formed by a set of nodes connected by links having different connotations forming the different layers of the multiplex. Characterizing the centrality of the nodes in a multiplex network is a challenging task since the centrality of the node naturally depends on the importance associated to links of a certain type. Here we propose to assign to each node of a multiplex network a centrality called Functional Multiplex PageRank that is a function of the weights given to every different pattern of connections (multilinks) existent in the multiplex network between any two nodes. Since multilinks distinguish all the possible ways in which the links in different layers can overlap, the Functional Multiplex PageRank can describe important non-linear effects when large relevance or small relevance is assigned to multilinks with overl...

  7. Phase noise reveals early category-specific modulation of the event-related potentials.

    Science.gov (United States)

    Németh, Kornél; Kovács, Petra; Vakli, Pál; Kovács, Gyula; Zimmer, Márta

    2014-01-01

    Previous studies have found that the amplitude of the early event-related potential (ERP) components evoked by faces, such as N170 and P2, changes systematically as a function of noise added to the stimuli. This change has been linked to an increased perceptual processing demand and to enhanced difficulty in perceptual decision making about faces. However, to date it has not yet been tested whether noise manipulation affects the neural correlates of decisions about face and non-face stimuli similarly. To this end, we measured the ERPs for faces and cars at three different phase noise levels. Subjects performed the same two-alternative age-discrimination task on stimuli chosen from young-old morphing continua that were created from faces as well as cars and were calibrated to lead to similar performances at each noise-level. Adding phase noise to the stimuli reduced performance and enhanced response latency for the two categories to the same extent. Parallel to that, phase noise reduced the amplitude and prolonged the latency of the face-specific N170 component. The amplitude of the P1 showed category-specific noise dependence: it was enhanced over the right hemisphere for cars and over the left hemisphere for faces as a result of adding phase noise to the stimuli, but remained stable across noise levels for cars over the left and for faces over the right hemisphere. Moreover, noise modulation altered the category-selectivity of the N170, while the P2 ERP component, typically associated with task decision difficulty, was larger for the more noisy stimuli regardless of stimulus category. Our results suggest that the category-specificity of noise-induced modulations of ERP responses starts at around 100 ms post-stimulus.

  8. Performance analysis of hybrid WDM-OTDM optical multicast overlay system employing 120 Gbps polarization and subcarrier multiplexed unicast signal with 40 Gbps multicast signal

    Science.gov (United States)

    Singh, Sukhbir; Singh, Surinder

    2017-02-01

    In this paper, we have propose and investigated the performance of hybrid WDM-OTDM optical multicast overlay system which employs 120 Gbps unicast and 40 Gbps multicast data operating over SMF+DCF and amplifier link in C-band. The polarization and subcarrier multiplexed modulation formats are used to obtain 120 Gbps unicast data and DPSK (differential phase shift keying) modulation format for 40 Gbps multicast data transmission. In multicast operation, DPSK data is superimposed on to multiplexed unicast data channels. The impact of extinction ratio, input power and transmission distance on the performance of proposed system in terms of output optical power, BER and Q-factor has been investigated for both unicast and multicast data. We have also concluded that polarization and subcarrier multiplexed modulation formats are promising option to increase per channel capacity and less vulnerable to CD and PMD. In addition, the proposed system using hybrid modulation techniques offers higher bandwidth utilization efficiency at higher per channel data rate than conventional modulation formats.

  9. Optimum design of phase opposition disposition pulse width modulation logic circuit for switching seven level cascaded half bridge inverter

    Directory of Open Access Journals (Sweden)

    Nentawe Y. Goshwe

    2016-06-01

    Full Text Available Theevolution of multilevel inverters (MLIs has made it possible to extract power from direct current (DC sources to alternating current (AC power. This paper presents the design of a novel phase opposition disposition pulse width modulation scheme (PODPWM logic circuit for a conventional single phase seven level cascaded H-Bridge (CHB inverter using Matlab/Simulink. The minimum switching logic circuit for the single phase seven level CHB inverter was obtained by modeling the logic equations that could be used with any number of levels depending on the number of modulating and carrier signals involved. The reduction in total harmonic distortion (THD of the output voltage for the MLI using low switching frequency at different modulation indixes is also investigated. The logic equations have made it easier to design a PODPWM circuit for any CHB inverter and the logic gates designed gave an optimum THD value of 16.73 % at modulation index of 0.20.

  10. Microwave photonic frequency down-conversion link based on intensity and phase paralleled modulation

    Science.gov (United States)

    Li, Jingnan; Wang, Yunxin; Wang, Dayong; Du, Haozheng; Zhou, Tao; Zhong, Xin; Yang, Dengcai; Li, Hongli

    2016-01-01

    A photonic microwave down-conversion approach is proposed and experimentally demonstrated based on a Mach-Zehnder modulator paralleled with a phase modulator. The incident radio frequency signal and the local oscillator signal are feed to the MZM and PM, respectively, and these two modulated optical signals interfere in the coupler. The useless higher-order sidebands are removed by a tunable optical band-pass filter. The principle of microwave frequency down-conversion is analyzed theoretically, the MZM and PM paralleled frequency down-conversion system is built. Then the performance of system is tested, and the experimental results show that the spurious-free dynamic range achieves 104.8 dB:Hz2/3. Compared to the conventional MZM-MZM cascaded system, the SFDR has been improved by 16 dB. The MZM and PM paralleled frequency down-conversion system can balance the intensity of the two coherent beams easily, and only single DC bias is needed. The proposed method possesses simple structure and high dynamic range.

  11. Cross-phase modulation in visible-pump/mid-infrared-probe spectroscopy

    Science.gov (United States)

    Lapini, Andrea; Vázquez, Sandra Mosquera; Touceda, Patricia Tourón; Lima, Manuela

    2011-05-01

    One of the most powerful tools to investigate the structural dynamics of electronically excited molecular systems is visible-pump/mid-infrared-probe spectroscopy. When performing this kind of experiments one must be aware of the artifacts deriving from the non-linear response of the solvent and of the sample cell itself. Cross-phase modulation (XPM) is observed when a strong visible-pump pulse modulates the refraction index seen by the mid-infrared-probe. The effect is enhanced when the probe pulse is chirped and causes the distortion of the transient signal in both the frequency and the time domains. We undertook a detailed simulation of XPM in the mid-infrared region where a visible pulse modulates the MIR pulse by XPM and in close conditions to the experimental ones. Our simulation takes into account the different group velocities of the pump and probe pulses and includes the influence of the linear chirp of the mid-infrared pulse and its asymmetry. The results of our numerical calculations fit very well the experimental signals measured in a 2 mm thick CaF 2 window.

  12. Module production for the Phase 1 upgrade of the CMS forward pixel detector

    Science.gov (United States)

    Siado Castaneda, Joaquin

    2017-01-01

    For Run 2 the Large Hadron Collider will run at a much higher instantaneous luminosity, which requires an upgrade of the CMS pixel detector. The detector consists of rectangular silicon sensors, segmented into 100 μm by 150 μm pixels, bonded to readout chips, with one sensor and a 8x2 array of readout chips forming a module. Due to its high granularity and good spatial resolution, about 10 μm for a single hit, the pixel detector is used for track reconstruction, pileup mitigation, and b-quark tagging in many physics analyses. Being the innermost sub-detector of CMS it receives the most radiation damage, and therefore needs to be replaced most often. For the phase 1 upgrade an additional disk in the forward region and increased buffer space in the readout chip will improve the pixel performance by increasing efficiency and reducing fake rates. The University of Nebraska-Lincoln is one of the two sites where modules are being assembled. This talk features the steps of the assembly process as well as challenges encountered and overcome during production of over 500 modules. The CMS Collaboration.

  13. Short-pulse cross-phase modulation in an electromagnetically-induced-transparency medium

    CERN Document Server

    Feizpour, Amir; Steinberg, Aephraim M

    2016-01-01

    Electromagnetically-induced transparency (EIT) has been proposed as a way to greatly enhance cross-phase modulation, with the possibility of leading to few-photon-level optical nonlinearities. This enhancement grows as the transparency window width, \\Delta_EIT, is narrowed. Decreasing \\Delta_EIT, however, increases the response time of the effect, suggesting that for pulses of a given duration, there could be a fundamental limit to the strength of the nonlinearity. We show that in the regimes of most practical interest - narrow EIT windows perturbed by short signal pulses- the enhancement offered by EIT is not only in the magnitude of the nonlinear phase shift but in fact also in its increased duration. That is, for the case of signal pulses much shorter (temporally) than the inverse EIT bandwidth, the narrow window serves to prolong the effect of the passing signal pulse, leading to an integrated phase shift that grows linearly with \\Delta_EIT even though the peak phase shift may saturate; the continued grow...

  14. Phase Clustering Based Modulation Classification Algorithm for PSK Signal over Wireless Environment

    Directory of Open Access Journals (Sweden)

    Qi An

    2016-01-01

    Full Text Available Promptitude and accuracy of signals’ non-data-aided (NDA identification is one of the key technology demands in noncooperative wireless communication network, especially in information monitoring and other electronic warfare. Based on this background, this paper proposes a new signal classifier for phase shift keying (PSK signals. The periodicity of signal’s phase is utilized as the assorted character, with which a fractional function is constituted for phase clustering. Classification and the modulation order of intercepted signals can be achieved through its Fast Fourier Transform (FFT of the phase clustering function. Frequency offset is also considered for practical conditions. The accuracy of frequency offset estimation has a direct impact on its correction. Thus, a feasible solution is supplied. In this paper, an advanced estimator is proposed for estimating the frequency offset and balancing estimation accuracy and range under low signal-to-noise ratio (SNR conditions. The influence on estimation range brought by the maximum correlation interval is removed through the differential operation of the autocorrelation of the normalized baseband signal raised to the power of Q. Then, a weighted summation is adopted for an effective frequency estimation. Details of equations and relevant simulations are subsequently presented. The estimator proposed can reach an estimation accuracy of 10-4 even when the SNR is as low as -15 dB. Analytical formulas are expressed, and the corresponding simulations illustrate that the classifier proposed is more efficient than its counterparts even at low SNRs.

  15. Direction-sensitive transverse velocity measurement by phase-modulated structured light beams.

    Science.gov (United States)

    Rosales-Guzmán, Carmelo; Hermosa, Nathaniel; Belmonte, Aniceto; Torres, Juan P

    2014-09-15

    The use of structured light beams to detect the velocity of targets moving perpendicularly to the beam's propagation axis opens new avenues for remote sensing of moving objects. However, determining the direction of motion is still a challenge because detection is usually done by means of an interferometric setup, which only provides an absolute value of the frequency shift. In this Letter, we present a novel method that addresses this issue. It uses dynamic control of the phase in the transverse plane of the structured light beam so that the direction of the particles' movement can be deduced. This is done by noting the change in the magnitude of the frequency shift as the transverse phase of the structured light is moved appropriately. We demonstrate our method with rotating microparticles that are illuminated by a Laguerre-Gaussian beam with a rotating phase about its propagation axis. Our method, which only requires a dynamically configurable optical beam generator, can easily be used with other types of motion by appropriate engineering and dynamic modulation of the phase of the light beam.

  16. Effect of higher order non-linearity in frequency variation of self-phase modulation in optical fiber communication

    Institute of Scientific and Technical Information of China (English)

    Abhijit Sinha; Sourangshu Mukhopadhyay

    2004-01-01

    In optical soliton propagation through a single mode optical fiber,it is established that self-phase mod ulation is maintained by the third order non-linearity of the silica-based glass material of the fiber.In this paper we show that the fifth order non-linearity has also some contribution in frequency variation of self-phase modulation.

  17. Utilization of a liquid crystal spatial light modulator in a gray scale detour phase method for Fourier holograms.

    Science.gov (United States)

    Makey, Ghaith; El-Daher, Moustafa Sayem; Al-Shufi, Kanj

    2012-11-10

    This paper introduces a new modification for the well-known binary detour phase method, which is largely used to represent Fourier holograms; the modification utilizes gray scale level control provided by a liquid crystal spatial light modulator to improve the traditional binary detour phase. Results are shown by both simulation and experiment.

  18. Phase-dependent reflex modulation in tibialis anterior during passive viewing of walking.

    Science.gov (United States)

    Behrendt, Frank; Wagner, Heiko; de Lussanet, Marc H E

    2013-03-01

    It is well established that reflexes are highly adaptive, as they depend both on our intention and on the active state of the muscles. Reflex gains change dynamically during actions such as walking and running, with the gain of cutaneous reflexes being increased at the end of the stance phase but decreased at the end of the swing phase in the tibialis anterior (TA) muscle. Reflex gains can even change during the mere observation of an action. The mechanisms and functions of such modulations are unclear. It has been suggested that the changed reflex gains prevent the actual performance of actions that we see. However, the modulation of reflexes in response to seeing an action has never been reproduced for the active execution of such actions. In the present study, medium-latency cutaneous reflexes from the TA muscle, of which the activity and reflexes during walking are well known, were measured in human subjects. The results show that the gain changes of the medium-latency responses of the TA are the same as during active walking. We conclude that reflexes do not represent an inhibitory mechanism that prevents motor output during action observation. Instead, our findings provide evidence that even the peripheral spinal motor system is actively involved in the motor resonance processes, without evoking any measurable motor responses. Copyright © 2013 Elsevier B.V. All rights reserved.

  19. Aerosol absorption measurement with a sinusoidal phase modulating fiber optic photo thermal interferometer

    Science.gov (United States)

    Li, Shuwang; Shao, Shiyong; Mei, Haiping; Rao, Ruizhong

    2016-10-01

    Aerosol light absorption plays an important role in the earth's atmosphere direct and semi-direct radiate forcing, simultaneously, it also has a huge influence on the visibility impairment and laser engineering application. Although various methods have been developed for measuring aerosol light absorption, huge challenge still remains in precision, accuracy and temporal resolution. The main reason is that, as a part of aerosol light extinction, aerosol light absorption always generates synchronously with aerosol light scattering, and unfortunately aerosol light scattering is much stronger in most cases. Here, a novel photo-thermal interferometry is proposed only for aerosol absorption measurement without disturbance from aerosol scattering. The photo-thermal interferometry consists of a sinusoidal phase-modulating single mode fiber-optic interferometer. The thermal dissipation, caused by aerosol energy from photo-thermal conversion when irritated by pump laser through interferometer, is detected. This approach is completely insensitive to aerosol scattering, and the single mode fiber-optic interferometer is compact, low-cost and insensitive to the polarization shading. The theory of this technique is illustrated, followed by the basic structure of the sinusoidal phase-modulating fiber-optic interferometer and demodulation algorithms. Qualitative and quantitative analysis results show that the new photo-thermal interference is a potential approach for aerosol absorption detection and environmental pollution detection.

  20. Negative Kerr Nonlinearity of Graphene as seen via Chirped-Pulse-Pumped Self-Phase Modulation

    Science.gov (United States)

    Vermeulen, Nathalie; Castelló-Lurbe, David; Cheng, JinLuo; Pasternak, Iwona; Krajewska, Aleksandra; Ciuk, Tymoteusz; Strupinski, Wlodek; Thienpont, Hugo; Van Erps, Jürgen

    2016-10-01

    We experimentally demonstrate a negative Kerr nonlinearity for quasiundoped graphene. Hereto, we introduce the method of chirped-pulse-pumped self-phase modulation and apply it to graphene-covered silicon waveguides at telecom wavelengths. The extracted Kerr-nonlinear index for graphene equals n2 ,gr=-10-13 m2 /W . Whereas the sign of n2 ,gr turns out to be negative in contrast to what has been assumed so far, its magnitude is in correspondence with that observed in earlier experiments. Graphene's negative Kerr nonlinearity strongly impacts how graphene should be exploited for enhancing the nonlinear response of photonic (integrated) devices exhibiting a positive nonlinearity. It also opens up the possibility of using graphene to annihilate unwanted nonlinear effects in such devices, to develop unexplored approaches for establishing Kerr processes, and to extend the scope of the "periodic poling" method often used for second-order nonlinearities towards third-order Kerr processes. Because of the generic nature of the chirped-pulse-pumped self-phase modulation method, it will allow fully characterizing the Kerr nonlinearity of essentially any novel (2D) material.

  1. Amplitude-Phase Modulation, Topological Horseshoe and Scaling Attractor of a Dynamical System

    Science.gov (United States)

    Li, Chun-Lai; Li, Wen; Zhang, Jing; Xie, Yuan-Xi; Zhao, Yi-Bo

    2016-09-01

    A three-dimensional autonomous chaotic system is discussed in this paper. Some basic dynamical properties of the system, including phase portrait, Poincaré map, power spectrum, Kaplan-Yorke dimension, Lyapunov exponent spectra, signal amplitude and topological horseshoe are studied theoretically and numerically. The main finding by analysis is that the signal amplitude can be modulated via controlling the coefficients of the linear term, cross-product term and squared term simultaneously or respectively, and the phase of x3 can be modulated by the product of the coefficients of the linear term and cross-product term. Furthermore, scaling chaotic attractors of this system are achieved by modified projective synchronization with an optimization-based linear coupling method, which is safer for secure communications than the existed synchronization scheme since the scaling factors can be regarded as the security encoding key. Supported by Hunan Provincial Natural Science Foundation of China under Grant No. 2016JJ4036, University Natural Science Foundation of Jiangsu Province under Grant No. 14KJB120007 and the National Natural Science Foundation of China under Grant Nos. 11504176 and 11602084

  2. Fourier transform infrared phase-modulated ellipsometry for in situ diagnostics of plasma-surface interactions

    Energy Technology Data Exchange (ETDEWEB)

    Shirafuji, T [International Innovation Center, Kyoto University, Sakyo-ku, Kyoto 606-8501 (Japan); Motomura, H [Department of Electronics, Kyoto University, Nishikyo-ku, Katsura 615-8510 (Japan); Tachibana, K [Department of Electronics, Kyoto University, Nishikyo-ku, Katsura 615-8510 (Japan)

    2004-03-21

    Applicability of Fourier transform infrared (FTIR) spectroscopy to an in situ diagnostics tool of plasma-surface interactions is described. After a brief review of conventional reflection absorption spectroscopy (RAS) and phase-modulated RAS (PMRAS), our FTIR phase-modulated spectroscopic ellipsometry (PMSE) is described in detail. The FTIR PMSE is constructed by insertion of a grid polarizer as an analyser in front of an infrared detector in addition to the conventional set-up of PMRAS. This simple change brings about a higher sensitivity than that of conventional PMRAS, which enables us to detect chemical species generated on (or removed from) the top surface layer during plasma processing. This feature is demonstrated by the fact that our FTIR PMSE can be applied to surface diagnostics during reactive ion etching processes such as for Si, SiO{sub 2}/Si, SiO{sub 2}/Si{sub 3}N{sub 4}, SiO{sub 2}/photo-resist and low-dielectric-constant films. (topical review)

  3. Emerging technologies and approaches to minimize discharges into Lake Michigan Phase 2, Module 3 report.

    Energy Technology Data Exchange (ETDEWEB)

    Negri, M. C.; Gillenwater, P.; Urgun Demirtas, M. (Energy Systems)

    2011-05-11

    Purdue University Calumet (Purdue) and Argonne National Laboratory (Argonne) have conducted an independent study to identify deployable technologies that could help the BP Whiting Refinery, and other petroleum refineries, meet future wastewater discharge limits. This study has been funded by BP. Each organization tested a subset of the target technologies and retains sole responsibility for its respective test design and implementation, quality assurance and control, test results obtained from each of the technologies, and corresponding conclusions and recommendations. This project was divided in two phases and modules. This report summarizes the work conducted by Argonne in Phase II Module 3 (Bench Scale Testing). Other Modules are discussed elsewhere (Emerging Technologies and Approaches to Minimize Discharges into Lake Michigan, Phase 2, Modules 1-3 Report, April 2011, prepared for BP Americas by the Argonne - Purdue Task Force). The goal of this project was to identify and assess available and emerging wastewater treatment technologies for removing mercury and vanadium from the Whiting Refinery wastewater and to conduct bench-scale tests to provide comparable, transparent, and uniform results across the broad range of technologies tested. After the bench-scale testing phase, a previously developed decision matrix was refined and applied by Argonne to process and review test data to estimate and compare the preliminary performance, engineering configuration, preliminary cost, energy usage, and waste generation of technologies that were shown to be able to remove Hg and/or V to below the target limit at the bench scale. The data were used as the basis to identify the best candidates for further testing at the bench or pilot scale on a slip stream of effluent to lake (ETL) or clarifier effluent (CE) at the Whiting Refinery to determine whether future limits could be met and to generate other pertinent data for scale-up and sustainability evaluation. As a result of

  4. Preface to the special issue on next-generation multiplexing schemes in fiber-based systems

    Science.gov (United States)

    Sillard, Pierre; Essiambre, René-Jean; Jung, Yongmin; Yamamoto, Takashi

    2017-02-01

    Since the beginning of optical communications in the late 70s, capacity has kept up with the exponential growth of traffic demand. This has been enabled by many technologies among which the most up-to-date wavelength multiplexing combined with coherent detection of polarized-multiplexed quadrature-amplitude-modulated signals. There is, however, a growing realization that this might no longer be sufficient and that next-generation multiplexing schemes are needed to avoid an imminent capacity crunch.

  5. Surface plasmon polariton excitation by electrostatic modulation and phase grating in indium-tin-oxide coated lithium niobate slabs

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Hao; Zhang, Jingwen; Zhao, Hua, E-mail: zhaohuaz@hit.edu.cn [Institute of Modern Optics, Department of Physics, Harbin Institute of Technology, Harbin 150001 (China); Key Laboratory of Micro-Optics and Photonics Technology of Heilongjiang Province, Harbin 150001 (China)

    2015-08-14

    Excitation of surface plasmon polaritons (SPPs) in a non-metal system in visible regime is discussed. With the assistance of phase grating resulted from photorefractive effect and electrostatic modulation of ITO induced by strong photovoltaic effect in iron-doped LiNbO{sub 3}, phase matching condition could be satisfied for SPP excitation in this semiconductor/dielectric system. Both the phase grating instead of metal grating and electrostatic modulation of semiconductor could be used for the design of tunable plasmonic devices based on nonlinear photorefractive crystals.

  6. Batching alternatives for Phase I retrieval wastes to be processed in WRAP Module 1

    Energy Technology Data Exchange (ETDEWEB)

    Mayancsik, B.A. [Westinghouse Hanford Co., Richland, WA (United States)

    1994-10-13

    During the next two decades, the transuranic (TRU) waste now stored in the 200 Area burial trenches and storage buildings is to be retrieved, processed in the Waste Receiving and Processing (WRAP) Module 1 facility, and shipped to a final disposal facility. The purpose of this document is to identify the criteria that can be used to batch suspect TRU waste, currently in retrievable storage, for processing through the WRAP Module 1 facility. These criteria are then used to generate a batch plan for Phase 1 Retrieval operations, which will retrieve the waste located in Trench 4C-04 of the 200 West Area burial ground. The reasons for batching wastes for processing in WRAP Module 1 include reducing the exposure of workers and the environment to hazardous material and ionizing radiation; maximizing the efficiency of the retrieval, processing, and disposal processes by reducing costs, time, and space throughout the process; reducing analytical sampling and analysis; and reducing the amount of cleanup and decontamination between process runs. The criteria selected for batching the drums of retrieved waste entering WRAP Module 1 are based on the available records for the wastes sent to storage as well as knowledge of the processes that generated these wastes. The batching criteria identified in this document include the following: waste generator; type of process used to generate or package the waste; physical waste form; content of hazardous/dangerous chemicals in the waste; radiochemical type and quantity of waste; drum weight; and special waste types. These criteria were applied to the waste drums currently stored in Trench 4C-04. At least one batching scheme is shown for each of the criteria listed above.

  7. Broadband receiver-based distortion elimination in phase-modulated analog optical links using four-wave mixing

    Science.gov (United States)

    Bhatia, Amit; Ting, Hong-Fu; Foster, Mark A.

    2015-03-01

    We present a method for full distortion elimination in phase-modulated analog optical links using the nonlinear optical process of four-wave mixing (FWM). Phase-modulated links consist of a laser and phase modulator in the transmitter and an interferometer (or local oscillator) and photodiode in the receiver. Phase modulation is a linear process, so distortion is introduced in the interferometric detection process. Quadrature biasing eliminates even-order distortion products, leaving only odd-order distortion. Here we introduce a method for eliminating these odd-order distortion products in the receiver. A small portion of the phase-modulated signal is tapped and combined with an unmodulated CW laser to seed a cascaded FWM comb source. This process generates an array of lightwaves with integer multiples of the signal's phase modulation. By suitably scaling and combining these lightwaves with the original signal the overall transfer function of the interferometric receiver can be linearized (or given another tailored shape) through a Fourier synthesis approach. By combining a single lightwave from the generated comb with the original signal, we demonstrate the complete elimination of third-order distortion from the phase-modulated link leaving fifth-order distortion as the dominate source of distortion. We show a 17.6-dB SFDR improvement (1-Hz bandwidth) for a 6 GHz link operating at 5-mA total photocurrent and a 16.4-dB SFDR improvement (1-Hz bandwidth) for a 15 GHz link operating at 10-mA total photocurrent. By appropriately combining additional lightwaves from the generated comb, higher-order distortion products can be eliminated to produce an ideal linear (or custom shaped) transfer function.

  8. Multiplex isothermal solid-phase recombinase polymerase amplification for the specific and fast DNA-based detection of three bacterial pathogens.

    Science.gov (United States)

    Kersting, Sebastian; Rausch, Valentina; Bier, Frank F; von Nickisch-Rosenegk, Markus

    2014-01-01

    We report on the development of an on-chip RPA (recombinase polymerase amplification) with simultaneous multiplex isothermal amplification and detection on a solid surface. The isothermal RPA was applied to amplify specific target sequences from the pathogens Neisseria gonorrhoeae, Salmonella enterica and methicillin-resistant Staphylococcus aureus (MRSA) using genomic DNA. Additionally, a positive plasmid control was established as an internal control. The four targets were amplified simultaneously in a quadruplex reaction. The amplicon is labeled during on-chip RPA by reverse oligonucleotide primers coupled to a fluorophore. Both amplification and spatially resolved signal generation take place on immobilized forward primers bount to expoxy-silanized glass surfaces in a pump-driven hybridization chamber. The combination of microarray technology and sensitive isothermal nucleic acid amplification at 38 °C allows for a multiparameter analysis on a rather small area. The on-chip RPA was characterized in terms of reaction time, sensitivity and inhibitory conditions. A successful enzymatic reaction is completed in isothermal nucleic acid amplification with RPA and spatially-resolved signal generation on specific immobilized oligonucleotides.

  9. Effects of walk-off on cross-phase modulation induced modulation instability in an optical fibre with high-order dispersion

    Institute of Scientific and Technical Information of China (English)

    Zhong Xian-Qiong; Xiang An-Ping

    2007-01-01

    This paper investigates the effects of walk-off among optical pulses on cross-phase modulation induced modulation instability in the normal dispersion region of an optical fibre with high-order dispersion. The results indicate that, in the case of high-order dispersion, the walk-off effect takes on new characteristics and will influence considerably the shape, position and especially the number of the spectral regions of the gain spectra of modulation instability. Not only the group-velocity mismatch, but also the difference of the third-order dispersion of two optical waves will alter the gain spectra of modulation instability but in different ways. Depending on the values of the walk-off parameters, the number of the spectral regions may increase from two to at most four, and the spectral shape and position may change too.

  10. Pulse Restoration for Long-Distance Transmission of Wavelength Division Multiplexed Signals Using Gain Saturable Erbium-Doped Fiber Amplifiers

    Science.gov (United States)

    Singh, Surinder

    2010-05-01

    In this article, the pulse restoration of different fibers is compared to obtain the optimum fiber. The dispersion-compensated fiber, having a high ability for pulse restoration, is optimized to reduce the self-phase modulation effect by taking the effective core area of the fiber. Then the optimized dispersion-compensated fibers are used in wavelength division multiplex transmission to increase the maximum distance of transmission. Here, 16 channels with a channel spacing of 200 GHz are modulated by an optical LiNbO3 phase modulator with non-return-to-zero format and transmitted over 1,050 km by using dispersion-compensated fibers with an effective core area of 30 pm2 and erbium-doped fiber amplifiers. The adequate quality factor and output power of different channels are observed at 70 km, 350 km, and 1,050 km. As the distance is increased, the quality factor falls.

  11. Design and analysis of low-loss linear analog phase modulator for deep space spacecraft X-band transponder (DST) application

    Science.gov (United States)

    Mysoor, Narayan R.; Mueller, Robert O.

    1991-01-01

    This paper summarizes the design concepts, analyses, and the development of an X-band transponder low-loss linear phase modulator for deep space spacecraft applications. A single section breadboard circulator-coupled reflection phase modulator has been analyzed, fabricated, and evaluated. Two- and three-cascaded sections have been modeled and simulations performed to provide an X-band DST phase modulator with +/- 2.5 radians of peak phase deviation to accommodate down-link signal modulation with composite telemetry data and ranging with a deviation linearity tolerance +/- 8 percent and insertion loss of less than 10 +/- 0.5 dB. A two-section phase modulator using constant gamma hyperabrupt varactors and an efficient modulator driver circuit was breadboarded. The measured results satisfy the DST phase modulator requirements, and excellent agreement with the predicted results.

  12. Design and analysis of low-loss linear analog phase modulator for deep space spacecraft X-band transponder (DST) application

    Science.gov (United States)

    Mysoor, Narayan R.; Mueller, Robert O.

    1991-01-01

    This paper summarizes the design concepts, analyses, and the development of an X-band transponder low-loss linear phase modulator for deep space spacecraft applications. A single section breadboard circulator-coupled reflection phase modulator has been analyzed, fabricated, and evaluated. Two- and three-cascaded sections have been modeled and simulations performed to provide an X-band DST phase modulator with +/- 2.5 radians of peak phase deviation to accommodate down-link signal modulation with composite telemetry data and ranging with a deviation linearity tolerance +/- 8 percent and insertion loss of less than 10 +/- 0.5 dB. A two-section phase modulator using constant gamma hyperabrupt varactors and an efficient modulator driver circuit was breadboarded. The measured results satisfy the DST phase modulator requirements, and excellent agreement with the predicted results.

  13. Multiplex editing system

    DEFF Research Database (Denmark)

    2015-01-01

    The present invention relates to a multiplex editing system. The system allows multiple editing of nucleic acid sequences such as genomic sequences, such as knockins of genes of interest in a genome, knockouts of genomic sequences and/or allele replacement. Also provided herein are a method...... for editing nucleic acids and a cell comprising a stably integrated endonuclease....

  14. Multiplex PageRank

    CERN Document Server

    Halu, Arda; Pansaraza, Pietro; Bianconi, Ginestra

    2013-01-01

    Many complex systems can be described as multiplex networks in which the same nodes can interact with one another in different layers, thus forming a set of interacting and co-evolving networks. Examples of such multiplex systems are social networks where people are involved in different types of relationships and interact through various forms of communication media. The ranking of nodes in multiplex networks is one of the most pressing and challenging tasks that research on complex networks is currently facing. When pairs of nodes can be connected through multiple links and in multiple layers, the ranking of nodes should necessarily reflect the importance of nodes in one layer as well as their importance in other interdependent layers. In this paper, we draw on the idea of biased random walks to define the Multiplex PageRank centrality measure in which the effects of the interplay between networks on the centrality of nodes are directly taken into account. In particular, depending on the intensity of the in...

  15. Arthrogryposis multiplex congenita

    DEFF Research Database (Denmark)

    Linnet, Karen Markussen; Balslev, Thomas; Møller-Madsen, Bjarne

    2015-01-01

    Arthrogryposis multiplex congenita (AMC) is a sign rather than a diagnosis. It implies contractures in multiple body areas and occurs in 1:3,000-5,000 live births. Primary aetiologies include neuropathic, myopathic, metabolic, end plate and vascular disorder affecting the developing foetus...

  16. The Microwave SQUID Multiplexer

    Science.gov (United States)

    Mates, John Arthur Benson

    2011-12-01

    This thesis describes a multiplexer of Superconducting Quantum Interference Devices (SQUIDs) with low-noise, ultra-low power dissipation, and great scalability. The multiplexer circuit measures the magnetic flux in a large number of unshunted rf SQUIDs by coupling each SQUID to a superconducting microwave resonator tuned to a unique resonance frequency and driving the resonators from a common feedline. A superposition of microwave tones measures each SQUID simultaneously using only two coaxial cables between the cryogenic device and room temperature. This multiplexer will enable the instrumentation of arrays with hundreds of thousands of low-temperature detectors for new applications in cosmology, materials analysis, and nuclear non-proliferation. The driving application of the Microwave SQUID Multiplexer is the readout of large arrays of superconducting transition-edge sensors, by some figures of merit the most sensitive detectors of electromagnetic signals over a span of more than nine orders of magnitude in energy, from 40 GHz microwaves to 200 keV gamma rays. Modern transition-edge sensors have noise-equivalent power as low as 10-20 W / Hz1/2 and energy resolution as good as 2 eV at 6 keV. These per-pixel sensitivities approach theoretical limits set by the underlying signals, motivating a rapid increase in pixel count to access new science. Compelling applications, like the non-destructive assay of nuclear material for treaty verification or the search for primordial gravity waves from inflation use arrays of these detectors to increase collection area or tile a focal plane. We developed three generations of SQUID multiplexers, optimizing the first for flux noise 0.17 muPhi0 / Hz1/2, the second for input current noise 19 pA / Hz1/2, and the last for practical multiplexing of large arrays of cosmic microwave background polarimeters based on transition-edge sensors. Using the last design we demonstrated multiplexed readout of prototype polarimeters with the

  17. All-gas-phase synthesis of UiO-66 through modulated atomic layer deposition

    Science.gov (United States)

    Lausund, Kristian Blindheim; Nilsen, Ola

    2016-01-01

    Thin films of stable metal-organic frameworks (MOFs) such as UiO-66 have enormous application potential, for instance in microelectronics. However, all-gas-phase deposition techniques are currently not available for such MOFs. We here report on thin-film deposition of the thermally and chemically stable UiO-66 in an all-gas-phase process by the aid of atomic layer deposition (ALD). Sequential reactions of ZrCl4 and 1,4-benzenedicarboxylic acid produce amorphous organic–inorganic hybrid films that are subsequently crystallized to the UiO-66 structure by treatment in acetic acid vapour. We also introduce a new approach to control the stoichiometry between metal clusters and organic linkers by modulation of the ALD growth with additional acetic acid pulses. An all-gas-phase synthesis technique for UiO-66 could enable implementations in microelectronics that are not compatible with solvothermal synthesis. Since this technique is ALD-based, it could also give enhanced thickness control and the possibility to coat irregular substrates with high aspect ratios. PMID:27876797

  18. All-gas-phase synthesis of UiO-66 through modulated atomic layer deposition

    Science.gov (United States)

    Lausund, Kristian Blindheim; Nilsen, Ola

    2016-11-01

    Thin films of stable metal-organic frameworks (MOFs) such as UiO-66 have enormous application potential, for instance in microelectronics. However, all-gas-phase deposition techniques are currently not available for such MOFs. We here report on thin-film deposition of the thermally and chemically stable UiO-66 in an all-gas-phase process by the aid of atomic layer deposition (ALD). Sequential reactions of ZrCl4 and 1,4-benzenedicarboxylic acid produce amorphous organic-inorganic hybrid films that are subsequently crystallized to the UiO-66 structure by treatment in acetic acid vapour. We also introduce a new approach to control the stoichiometry between metal clusters and organic linkers by modulation of the ALD growth with additional acetic acid pulses. An all-gas-phase synthesis technique for UiO-66 could enable implementations in microelectronics that are not compatible with solvothermal synthesis. Since this technique is ALD-based, it could also give enhanced thickness control and the possibility to coat irregular substrates with high aspect ratios.

  19. Extracting information from multiplex networks.

    Science.gov (United States)

    Iacovacci, Jacopo; Bianconi, Ginestra

    2016-06-01

    Multiplex networks are generalized network structures that are able to describe networks in which the same set of nodes are connected by links that have different connotations. Multiplex networks are ubiquitous since they describe social, financial, engineering, and biological networks as well. Extending our ability to analyze complex networks to multiplex network structures increases greatly the level of information that is possible to extract from big data. For these reasons, characterizing the centrality of nodes in multiplex networks and finding new ways to solve challenging inference problems defined on multiplex networks are fundamental questions of network science. In this paper, we discuss the relevance of the Multiplex PageRank algorithm for measuring the centrality of nodes in multilayer networks and we characterize the utility of the recently introduced indicator function Θ̃(S) for describing their mesoscale organization and community structure. As working examples for studying these measures, we consider three multiplex network datasets coming for social science.

  20. Extracting information from multiplex networks

    Science.gov (United States)

    Iacovacci, Jacopo; Bianconi, Ginestra

    2016-06-01

    Multiplex networks are generalized network structures that are able to describe networks in which the same set of nodes are connected by links that have different connotations. Multiplex networks are ubiquitous since they describe social, financial, engineering, and biological networks as well. Extending our ability to analyze complex networks to multiplex network structures increases greatly the level of information that is possible to extract from big data. For these reasons, characterizing the centrality of nodes in multiplex networks and finding new ways to solve challenging inference problems defined on multiplex networks are fundamental questions of network science. In this paper, we discuss the relevance of the Multiplex PageRank algorithm for measuring the centrality of nodes in multilayer networks and we characterize the utility of the recently introduced indicator function Θ ˜ S for describing their mesoscale organization and community structure. As working examples for studying these measures, we consider three multiplex network datasets coming for social science.