WorldWideScience

Sample records for multiple production sources

  1. Gas production strategy of underground coal gasification based on multiple gas sources.

    Tianhong, Duan; Zuotang, Wang; Limin, Zhou; Dongdong, Li

    2014-01-01

    To lower stability requirement of gas production in UCG (underground coal gasification), create better space and opportunities of development for UCG, an emerging sunrise industry, in its initial stage, and reduce the emission of blast furnace gas, converter gas, and coke oven gas, this paper, for the first time, puts forward a new mode of utilization of multiple gas sources mainly including ground gasifier gas, UCG gas, blast furnace gas, converter gas, and coke oven gas and the new mode was demonstrated by field tests. According to the field tests, the existing power generation technology can fully adapt to situation of high hydrogen, low calorific value, and gas output fluctuation in the gas production in UCG in multiple-gas-sources power generation; there are large fluctuations and air can serve as a gasifying agent; the gas production of UCG in the mode of both power and methanol based on multiple gas sources has a strict requirement for stability. It was demonstrated by the field tests that the fluctuations in gas production in UCG can be well monitored through a quality control chart method.

  2. Gas Production Strategy of Underground Coal Gasification Based on Multiple Gas Sources

    Duan Tianhong

    2014-01-01

    Full Text Available To lower stability requirement of gas production in UCG (underground coal gasification, create better space and opportunities of development for UCG, an emerging sunrise industry, in its initial stage, and reduce the emission of blast furnace gas, converter gas, and coke oven gas, this paper, for the first time, puts forward a new mode of utilization of multiple gas sources mainly including ground gasifier gas, UCG gas, blast furnace gas, converter gas, and coke oven gas and the new mode was demonstrated by field tests. According to the field tests, the existing power generation technology can fully adapt to situation of high hydrogen, low calorific value, and gas output fluctuation in the gas production in UCG in multiple-gas-sources power generation; there are large fluctuations and air can serve as a gasifying agent; the gas production of UCG in the mode of both power and methanol based on multiple gas sources has a strict requirement for stability. It was demonstrated by the field tests that the fluctuations in gas production in UCG can be well monitored through a quality control chart method.

  3. Neutron source multiplication method

    Clayton, E.D.

    1985-01-01

    Extensive use has been made of neutron source multiplication in thousands of measurements of critical masses and configurations and in subcritical neutron-multiplication measurements in situ that provide data for criticality prevention and control in nuclear materials operations. There is continuing interest in developing reliable methods for monitoring the reactivity, or k/sub eff/, of plant operations, but the required measurements are difficult to carry out and interpret on the far subcritical configurations usually encountered. The relationship between neutron multiplication and reactivity is briefly discussed and data presented to illustrate problems associated with the absolute measurement of neutron multiplication and reactivity in subcritical systems. A number of curves of inverse multiplication have been selected from a variety of experiments showing variations observed in multiplication during the course of critical and subcritical experiments where different methods of reactivity addition were used, with different neutron source detector position locations. Concern is raised regarding the meaning and interpretation of k/sub eff/ as might be measured in a far subcritical system because of the modal effects and spectrum differences that exist between the subcritical and critical systems. Because of this, the calculation of k/sub eff/ identical with unity for the critical assembly, although necessary, may not be sufficient to assure safety margins in calculations pertaining to far subcritical systems. Further study is needed on the interpretation and meaning of k/sub eff/ in the far subcritical system

  4. High brightness--multiple beamlets source for patterned X-ray production

    Leung, Ka-Ngo [Hercules, CA; Ji, Qing [Albany, CA; Barletta, William A [Oakland, CA; Jiang, Ximan [El Cerrito, CA; Ji, Lili [Albany, CA

    2009-10-27

    Techniques for controllably directing beamlets to a target substrate are disclosed. The beamlets may be either positive ions or electrons. It has been shown that beamlets may be produced with a diameter of 1 .mu.m, with inter-aperture spacings of 12 .mu.m. An array of such beamlets, may be used for maskless lithography. By step-wise movement of the beamlets relative to the target substrate, individual devices may be directly e-beam written. Ion beams may be directly written as well. Due to the high brightness of the beamlets from extraction from a multicusp source, exposure times for lithographic exposure are thought to be minimized. Alternatively, the beamlets may be electrons striking a high Z material for X-ray production, thereafter collimated to provide patterned X-ray exposures such as those used in CAT scans. Such a device may be used for remote detection of explosives.

  5. Plume rise from multiple sources

    Briggs, G.A.

    1975-01-01

    A simple enhancement factor for plume rise from multiple sources is proposed and tested against plume-rise observations. For bent-over buoyant plumes, this results in the recommendation that multiple-source rise be calculated as [(N + S)/(1 + S)]/sup 1/3/ times the single-source rise, Δh 1 , where N is the number of sources and S = 6 (total width of source configuration/N/sup 1/3/ Δh 1 )/sup 3/2/. For calm conditions a crude but simple method is suggested for predicting the height of plume merger and subsequent behavior which is based on the geometry and velocity variations of a single buoyant plume. Finally, it is suggested that large clusters of buoyant sources might occasionally give rise to concentrated vortices either within the source configuration or just downwind of it

  6. Connecting the Production Multiple

    Lichen, Alex Yu; Mouritsen, Jan

    &OP process itself is a fluid object, but there is still possibility to organise the messy Production. There are connections between the Production multiple and the managerial technology fluid. The fluid enacted the multiplicity of Production thus making it more difficult to be organised because there were...... in opposite directions. They are all part of the fluid object. There is no single chain of circulating references that makes the object a matter of fact. Accounting fluidity means that references drift back and forth and enact new realities also connected to the chain. In this setting future research may......This paper is about objects. It follows post ANT trajectories and finds that objects are multiple and fluid. Extant classic ANT inspired accounting research largely sees accounting inscriptions as immutable mobiles. Although multiplicity of objects upon which accounting acts has been explored...

  7. Production of sealed sources

    Bandi, L.N.

    2016-01-01

    Radioisotope production has been an ongoing activity in India since the sixties. Radioisotopes find wide-ranging applications in various fields, including industry, research, agriculture and medicine. Board of Radiation and Isotope Technology, an industrial unit of Department of Atomic Energy is involved in fabrication and supply of wide variety of sealed sources. The main radioisotopes fabricated and supplied by BRIT are Cobalt-60, Iridium-192. These isotopes are employed in industrial and laboratory irradiators, teletherapy machines, radiography exposure devices, nucleonic gauges. The source fabrication facilities of BRIT are located at Rajasthan Atomic Power Project Cobalt-60 Facility (RAPPCOF), Kota, Radiological Laboratories Group (RLG) and High Intensity Radiation Utilization Project (HIRUP) at Trombay

  8. Geometrical model of multiple production

    Chikovani, Z.E.; Jenkovszky, L.L.; Kvaratshelia, T.M.; Struminskij, B.V.

    1988-01-01

    The relation between geometrical and KNO-scaling and their violation is studied in a geometrical model of multiple production of hadrons. Predictions concerning the behaviour of correlation coefficients at future accelerators are given

  9. Mechanisms of multiple production processes

    Dremin, I.M.

    1977-01-01

    Theoretical approaches to multiple production processes are discussed. A large number of models proceeds from the notion about common excited system produced by colliding hadrons. This class of models includes the hydrodynamical, statistical, thermodynamical and statistical bootstrap models. Sometimes the production process is due to excitation and decay of two colliding particles. The fragmentation bremsstrahlung and inelastic diffraction models belong to this group. The largest group of models describes the multiple production process as a result of formation of many excited centers. The typical example is the multiperipheral model. An interesting direction is given by the attempts to interrelate the mechanism of multiple production with internal structure of particles that is with their constituents (C-group)'-quarks, gluons, etc. Besides the models there are phenomenological (p group) attempts to connect different features of multiple production. Experimental data indicate the existence of leading and pionization particles thus giving an evidence for applications of different models. The data about increase of total and inclusive cross sections, the behaviour of the mean multiplicity and correlations at high energies provide a clue for further development of multiple production theory

  10. Land Streamer Surveying Using Multiple Sources

    Mahmoud, Sherif

    2014-12-11

    Various examples are provided for land streamer seismic surveying using multiple sources. In one example, among others, a method includes disposing a land streamer in-line with first and second shot sources. The first shot source is at a first source location adjacent to a proximal end of the land streamer and the second shot source is at a second source location separated by a fixed length corresponding to a length of the land streamer. Shot gathers can be obtained when the shot sources are fired. In another example, a system includes a land streamer including a plurality of receivers, a first shot source located adjacent to the proximal end of the land streamer, and a second shot source located in-line with the land streamer and the first shot source. The second shot source is separated from the first shot source by a fixed overall length corresponding to the land streamer.

  11. Culture medium pH influence on Gluconacetobacter physiology: Cellulose production rate and yield enhancement in presence of multiple carbon sources.

    Yassine, Fatima; Bassil, Nathalie; Flouty, Roula; Chokr, Ali; Samrani, Antoine El; Boiteux, Gisèle; Tahchi, Mario El

    2016-08-01

    Gluconacetobacter genera are valued for bacterial cellulose (BC) and acetic acid production. BC is produced at optimal yields in classical microbiological media that are expensive for a large scale of production. In addition, BC usage for industrial purposes is limited due to low conversion rate into cellulose and to long incubation duration. In this paper, Gluconacetobacter isolated from apple vinegar was kinetically studied to evaluate cellulose production in presence of different carbon sources. Acetic and citric acid effect on Gluconacetobacter metabolism is clarified. It was shown that Gluconacetobacter uses glucose as a primary carbon source for cells growth and products formation. Acetic acid employment as a co-carbon source in Hestrin Schramm medium showed an increase of 17% in BC yield with a moderate decrease in the crystallite size of the resulting polymer. Copyright © 2016 Elsevier Ltd. All rights reserved.

  12. Fission-product source terms

    Lorenz, R.A.

    1981-01-01

    This presentation consists of a review of fission-product source terms for light water reactor (LWR) fuel. A source term is the quantity of fission products released under specified conditions that can be used to calculate the consequences of the release. The source term usually defines release from breached fuel-rod cladding but could also describe release from the primary coolant system, the reactor containment shell, or the site boundary. The source term would be different for each locality, and the chemical and physical forms of the fission products could also differ

  13. The multiple Dirichlet product and the multiple Dirichlet series

    Onozuka, Tomokazu

    2016-01-01

    First, we define the multiple Dirichlet product and study the properties of it. From those properties, we obtain a zero-free region of a multiple Dirichlet series and a multiple Dirichlet series expression of the reciprocal of a multiple Dirichlet series.

  14. Thermionic detector with multiple layered ionization source

    Patterson, P. L.

    1985-01-01

    Method and apparatus for analyzing specific chemical substances in a gaseous environment comprises a thermionic source formed of multiple layers of ceramic material composition, an electrical current instrumentality for heating the thermionic source to operating temperatures in the range of 100 0 C. to 1000 0 C., an instrumentality for exposing the surface of the thermionic source to contact with the specific chemical substances for the purpose of forming gas phase ionization of the substances by a process of electrical charge emission from the surface, a collector electrode disposed adjacent to the thermiomic source, an instrumentality for biasing the thermionic source at an electrical potential which causes the gas phase ions to move toward the collector, and an instrumentality for measuring the ion current arriving at the collector. The thermionic source is constructed of a metallic heater element molded inside a sub-layer of hardened ceramic cement material impregnated with a metallic compound additive which is non-corrosive to the heater element during operation. The sub-layer is further covered by a surface-layer formed of hardened ceramic cement material impregnated with an alkali metal compound in a manner that eliminates corrosive contact of the alkali compounds with the heater element. The sub-layer further protects the heater element from contact with gas environments which may be corrosive. The specific ionization of different chemical substances is varied over a wide range by changing the composition and temperature of the thermionic source, and by changing the composition of the gas environment

  15. Binaural Processing of Multiple Sound Sources

    2016-08-18

    AFRL-AFOSR-VA-TR-2016-0298 Binaural Processing of Multiple Sound Sources William Yost ARIZONA STATE UNIVERSITY 660 S MILL AVE STE 312 TEMPE, AZ 85281...18-08-2016 2. REPORT TYPE Final Performance 3. DATES COVERED (From - To) 15 Jul 2012 to 14 Jul 2016 4. TITLE AND SUBTITLE Binaural Processing of...three topics cited above are entirely within the scope of the AFOSR grant. 15. SUBJECT TERMS Binaural hearing, Sound Localization, Interaural signal

  16. Cluster concept in multiple hadron production

    Dremin, I.M.; Quigg, C.

    1978-01-01

    The general features of high-energy collisions of elementary particles are outlined. It is argued that multiple production occurs through the production of hadronic clusters. The history and present status of the cluster concept are surveyed

  17. AVOCADO SEEDLINGS MULTIPLE STEMS PRODUCTION

    MARCUS VINICIUS SANDOVAL PAIXÃO

    2016-01-01

    Full Text Available ABSTRACT This study aimed to evaluate the potential of multi-stems in avocado seeds according to their mass as well as the adventitious rooting of multi-stem budding with or without the use of auxin. The research was carried out at the Vegetation House of Federal Institute of Espírito Santo, Campus Santa Teresa -ES, with seeds of different masses: 100 g, in which each experimental unit was made of five seeds, distributed within five repetitions, under a completely randomized design. The seeds were put to germinate and the percentage number of emergence and multiple stems were evaluated. After 150 days, the following evaluations were carried out: survival of rooted cuttings; number of leaves; stem diameter; root length; root volume; root and shoot fresh mass; root and shoot dry mass; shoot height; absolute growth and shoot growth rate; shoot dry weight/root dry mass ratio; shoot height/stem diameter ratio; shoot height/root length and Dickson's quality index ratio. Avocado seeds with mass over 100 g and between 81-100 g presented higher percentage of multiple stems. Rods over 20 cm that were not treated with IBA (indole-3-butyric acid resulted on avocado plants of better quality. The use of IBA (2000 mg L-1 does not affect the rooting and growth of avocado's multi-stem plants.

  18. 46 CFR 111.10-5 - Multiple energy sources.

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Multiple energy sources. 111.10-5 Section 111.10-5...-GENERAL REQUIREMENTS Power Supply § 111.10-5 Multiple energy sources. Failure of any single generating set energy source such as a boiler, diesel, gas turbine, or steam turbine must not cause all generating sets...

  19. Integrating multiple data sources for malware classification

    Anderson, Blake Harrell; Storlie, Curtis B; Lane, Terran

    2015-04-28

    Disclosed herein are representative embodiments of tools and techniques for classifying programs. According to one exemplary technique, at least one graph representation of at least one dynamic data source of at least one program is generated. Also, at least one graph representation of at least one static data source of the at least one program is generated. Additionally, at least using the at least one graph representation of the at least one dynamic data source and the at least one graph representation of the at least one static data source, the at least one program is classified.

  20. Land Streamer Surveying Using Multiple Sources

    Mahmoud, Sherif; Schuster, Gerard T.

    2014-01-01

    are fired. In another example, a system includes a land streamer including a plurality of receivers, a first shot source located adjacent to the proximal end of the land streamer, and a second shot source located in-line with the land streamer and the first

  1. Reconstruction of multiple line source attenuation maps

    Celler, A.; Sitek, A.; Harrop, R.

    1996-01-01

    A simple configuration for a transmission source for the single photon emission computed tomography (SPECT) was proposed, which utilizes a series of collimated line sources parallel to the axis of rotation of a camera. The detector is equipped with a standard parallel hole collimator. We have demonstrated that this type of source configuration can be used to generate sufficient data for the reconstruction of the attenuation map when using 8-10 line sources spaced by 3.5-4.5 cm for a 30 x 40cm detector at 65cm distance from the sources. Transmission data for a nonuniform thorax phantom was simulated, then binned and reconstructed using filtered backprojection (FBP) and iterative methods. The optimum maps are obtained with data binned into 2-3 bins and FBP reconstruction. The activity in the source was investigated for uniform and exponential activity distributions, as well as the effect of gaps and overlaps of the neighboring fan beams. A prototype of the line source has been built and the experimental verification of the technique has started

  2. Research on neutron source multiplication method in nuclear critical safety

    Zhu Qingfu; Shi Yongqian; Hu Dingsheng

    2005-01-01

    The paper concerns in the neutron source multiplication method research in nuclear critical safety. Based on the neutron diffusion equation with external neutron source the effective sub-critical multiplication factor k s is deduced, and k s is different to the effective neutron multiplication factor k eff in the case of sub-critical system with external neutron source. The verification experiment on the sub-critical system indicates that the parameter measured with neutron source multiplication method is k s , and k s is related to the external neutron source position in sub-critical system and external neutron source spectrum. The relation between k s and k eff and the effect of them on nuclear critical safety is discussed. (author)

  3. Learning from Multiple Sources for Video Summarisation

    Zhu, Xiatian; Loy, Chen Change; Gong, Shaogang

    2015-01-01

    Many visual surveillance tasks, e.g.video summarisation, is conventionally accomplished through analysing imagerybased features. Relying solely on visual cues for public surveillance video understanding is unreliable, since visual observations obtained from public space CCTV video data are often not sufficiently trustworthy and events of interest can be subtle. On the other hand, non-visual data sources such as weather reports and traffic sensory signals are readily accessible but are not exp...

  4. Volcano Monitoring using Multiple Remote Data Sources

    Reath, K. A.; Pritchard, M. E.

    2016-12-01

    Satellite-based remote sensing instruments can be used to determine quantitative values related to precursory activity that can act as a warning sign of an upcoming eruption. These warning signs are measured through examining anomalous activity in: (1) thermal flux, (2) gas/aerosol emission rates, (3) ground deformation, and (4) ground-based seismic readings. Patterns in each of these data sources are then analyzed to create classifications of different phases of precursory activity. These different phases of activity act as guidelines to monitor the progression of precursory activity leading to an eruption. Current monitoring methods rely on using high temporal resolution satellite imagery from instruments like the Advanced Very High Resolution Radiometer (AVHRR) and the Moderate Resolution Imaging Spectrometer (MODIS) sensors, for variations in thermal and aerosol emissions, and the Ozone Monitoring Instruments (OMI) and Ozone Mapping Profiler Suite (OMPS) instruments, for variations in gas emissions, to provide a valuable resource for near real-time monitoring of volcanic activity. However, the low spatial resolution of these data only enable events that produce a high thermal output or a large amount of gas/aerosol emissions to be detected. High spatial resolution instruments, like the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) sensor, have a small enough pixel size (90m2) that the subtle variations in both thermal flux and gas/aerosol emission rates in the pre-eruptive period can be detected. Including these data with the already established high temporal resolution data helps to identify and classify precursory activity patterns months before an eruption (Reath et al, 2016). By correlating these data with ground surface deformation data, determined from the Interferometric Synthetic Aperture Radar (InSAR) sensor, and seismic data, collected by the Incorporated Research Institution for Seismology (IRIS) data archive, subtle

  5. Surface negative ion production in ion sources

    Belchenko, Y.

    1993-01-01

    Negative ion sources and the mechanisms for negative ion production are reviewed. Several classes of sources with surface origin of negative ions are examined in detail: surface-plasma sources where ion production occurs on the electrode in contact with the plasma, and ''pure surface'' sources where ion production occurs due to conversion or desorption processes. Negative ion production by backscattering, impact desorption, and electron- and photo-stimulated desorption are discussed. The experimental efficiencies of intense surface negative ion production realized on electrodes contacted with hydrogen-cesium or pure hydrogen gas-discharge plasma are compared. Recent modifications of surface-plasma sources developed for accelerator and fusion applications are reviewed in detail

  6. Introducing Product Lines through Open Source Tools

    Haugen, Øystein

    2008-01-01

    We present an approach to introducing product lines to companies that lower their initial risk by applying open source tools and a smooth learning curve into the use and creation of domain specific modeling combined with standardized variability modeling.

  7. The Chandra Source Catalog: Source Properties and Data Products

    Rots, Arnold; Evans, Ian N.; Glotfelty, Kenny J.; Primini, Francis A.; Zografou, Panagoula; Anderson, Craig S.; Bonaventura, Nina R.; Chen, Judy C.; Davis, John E.; Doe, Stephen M.; Evans, Janet D.; Fabbiano, Giuseppina; Galle, Elizabeth C.; Gibbs, Danny G., II; Grier, John D.; Hain, Roger; Hall, Diane M.; Harbo, Peter N.; He, Xiang Qun (Helen); Houck, John C.; Karovska, Margarita; Kashyap, Vinay L.; Lauer, Jennifer; McCollough, Michael L.; McDowell, Jonathan C.; Miller, Joseph B.; Mitschang, Arik W.; Morgan, Douglas L.; Mossman, Amy E.; Nichols, Joy S.; Nowak, Michael A.; Plummer, David A.; Refsdal, Brian L.; Siemiginowska, Aneta L.; Sundheim, Beth A.; Tibbetts, Michael S.; van Stone, David W.; Winkelman, Sherry L.

    2009-09-01

    The Chandra Source Catalog (CSC) is breaking new ground in several areas. There are two aspects that are of particular interest to the users: its evolution and its contents. The CSC will be a living catalog that becomes richer, bigger, and better in time while still remembering its state at each point in time. This means that users will be able to take full advantage of new additions to the catalog, while retaining the ability to back-track and return to what was extracted in the past. The CSC sheds the limitations of flat-table catalogs. Its sources will be characterized by a large number of properties, as usual, but each source will also be associated with its own specific data products, allowing users to perform mini custom analysis on the sources. Source properties fall in the spatial (position, extent), photometric (fluxes, count rates), spectral (hardness ratios, standard spectral fits), and temporal (variability probabilities) domains, and are all accompanied by error estimates. Data products cover the same coordinate space and include event lists, images, spectra, and light curves. In addition, the catalog contains data products covering complete observations: event lists, background images, exposure maps, etc. This work is supported by NASA contract NAS8-03060 (CXC).

  8. Coordinating a Large, Amalgamated REU Program with Multiple Funding Sources

    Fiorini, Eugene; Myers, Kellen; Naqvi, Yusra

    2017-01-01

    In this paper, we discuss the challenges of organizing a large REU program amalgamated from multiple funding sources, including diverse participants, mentors, and research projects. We detail the program's structure, activities, and recruitment, and we hope to demonstrate that the organization of this REU is not only beneficial to its…

  9. Evaluation of Network Reliability for Computer Networks with Multiple Sources

    Yi-Kuei Lin

    2012-01-01

    Full Text Available Evaluating the reliability of a network with multiple sources to multiple sinks is a critical issue from the perspective of quality management. Due to the unrealistic definition of paths of network models in previous literature, existing models are not appropriate for real-world computer networks such as the Taiwan Advanced Research and Education Network (TWAREN. This paper proposes a modified stochastic-flow network model to evaluate the network reliability of a practical computer network with multiple sources where data is transmitted through several light paths (LPs. Network reliability is defined as being the probability of delivering a specified amount of data from the sources to the sink. It is taken as a performance index to measure the service level of TWAREN. This paper studies the network reliability of the international portion of TWAREN from two sources (Taipei and Hsinchu to one sink (New York that goes through a submarine and land surface cable between Taiwan and the United States.

  10. Multisensory softness perceived compliance from multiple sources of information

    Luca, Massimiliano Di

    2014-01-01

    Offers a unique multidisciplinary overview of how humans interact with soft objects and how multiple sensory signals are used to perceive material properties, with an emphasis on object deformability. The authors describe a range of setups that have been employed to study and exploit sensory signals involved in interactions with compliant objects as well as techniques to simulate and modulate softness - including a psychophysical perspective of the field. Multisensory Softness focuses on the cognitive mechanisms underlying the use of multiple sources of information in softness perception. D

  11. Multiple stressors for oceanic primary production

    Agusti, Susana

    2015-12-15

    Marine ecosystems are increasingly exposed to stress factors of anthropogenic origin that change their function, structure and services they deliver society. Climate change occurs simultaneously with other changes in the environment acting jointly in a context of global environmental change. For oceanic phytoplankton communities, the research conducted so far has identified stress factors associated with global change and their impact individually (warming, acidification, increased UVB radiation, pollutants). But when several stressors act simultaneously interactions and responses are not equal to the sum of individual impacts, but may have synergistic effects (the effects are multiplied) or antagonistic (cancel out the effects) that hinder predictions of the vulnerability of ecosystems to global change. Here we will examine the vulnerability of oceanic primary producers to the accumulation of different stressors associated with global change. The trend for autotrophic picoplankton to increase with temperature in the ocean has led to predictions that autotrophic picoplankton abundance will increase with warming. However, it is documented a trend towards a decline in productivity, due to declined autotroph biomass and production with warming and the associated stratification in the subtropical ocean. Models predicting an increase in abundance are in contradiction with the reported decrease in productivity in several oceanic areas, and associate oligotrophication. Here we perform a global study to analyze the relationships of autotrophic picoplankton with oceanic temperature, nutrients, underwater light and ultraviolet B (UVB) radiation, and productivity. We built a model to project the future changes of autotrophic picoplankton considering multiple environmental changes in future climate scenarios for the subtropical gyres. We considered increased water temperature, and associated changes in productivity and underwater light and UVB. The model show that warming and

  12. Multiple stressors for oceanic primary production

    Agusti, Susana; Llabré s, Moira; Lubiá n, Luis M.; Moreno-Ostos, Enrique; Estrada, Marta; Duarte, Carlos M.; Cerezo, Maria I.

    2015-01-01

    Marine ecosystems are increasingly exposed to stress factors of anthropogenic origin that change their function, structure and services they deliver society. Climate change occurs simultaneously with other changes in the environment acting jointly in a context of global environmental change. For oceanic phytoplankton communities, the research conducted so far has identified stress factors associated with global change and their impact individually (warming, acidification, increased UVB radiation, pollutants). But when several stressors act simultaneously interactions and responses are not equal to the sum of individual impacts, but may have synergistic effects (the effects are multiplied) or antagonistic (cancel out the effects) that hinder predictions of the vulnerability of ecosystems to global change. Here we will examine the vulnerability of oceanic primary producers to the accumulation of different stressors associated with global change. The trend for autotrophic picoplankton to increase with temperature in the ocean has led to predictions that autotrophic picoplankton abundance will increase with warming. However, it is documented a trend towards a decline in productivity, due to declined autotroph biomass and production with warming and the associated stratification in the subtropical ocean. Models predicting an increase in abundance are in contradiction with the reported decrease in productivity in several oceanic areas, and associate oligotrophication. Here we perform a global study to analyze the relationships of autotrophic picoplankton with oceanic temperature, nutrients, underwater light and ultraviolet B (UVB) radiation, and productivity. We built a model to project the future changes of autotrophic picoplankton considering multiple environmental changes in future climate scenarios for the subtropical gyres. We considered increased water temperature, and associated changes in productivity and underwater light and UVB. The model show that warming and

  13. Tracking of Multiple Moving Sources Using Recursive EM Algorithm

    Böhme Johann F

    2005-01-01

    Full Text Available We deal with recursive direction-of-arrival (DOA estimation of multiple moving sources. Based on the recursive EM algorithm, we develop two recursive procedures to estimate the time-varying DOA parameter for narrowband signals. The first procedure requires no prior knowledge about the source movement. The second procedure assumes that the motion of moving sources is described by a linear polynomial model. The proposed recursion updates the polynomial coefficients when a new data arrives. The suggested approaches have two major advantages: simple implementation and easy extension to wideband signals. Numerical experiments show that both procedures provide excellent results in a slowly changing environment. When the DOA parameter changes fast or two source directions cross with each other, the procedure designed for a linear polynomial model has a better performance than the general procedure. Compared to the beamforming technique based on the same parameterization, our approach is computationally favorable and has a wider range of applications.

  14. Multiple LDPC decoding for distributed source coding and video coding

    Forchhammer, Søren; Luong, Huynh Van; Huang, Xin

    2011-01-01

    Distributed source coding (DSC) is a coding paradigm for systems which fully or partly exploit the source statistics at the decoder to reduce the computational burden at the encoder. Distributed video coding (DVC) is one example. This paper considers the use of Low Density Parity Check Accumulate...... (LDPCA) codes in a DSC scheme with feed-back. To improve the LDPC coding performance in the context of DSC and DVC, while retaining short encoder blocks, this paper proposes multiple parallel LDPC decoding. The proposed scheme passes soft information between decoders to enhance performance. Experimental...

  15. Research on amplification multiple of source neutron number for ADS

    Liu Guisheng; Zhao Zhixiang; Zhang Baocheng; Shen Qingbiao; Ding Dazhao

    1998-01-01

    NJOY-91.91 and MILER code systems was applied to process and generate 44 group cross sections in AMPX master library format from CENDL-2 and ENDF/B-6. It is important an ADS (Accelerator-Driven System) assembly spectrum is used as the weighting spectrum for generating multi-group constants. Amplification multiples of source neutron number for several fast assemblies were calculated

  16. 75 FR 69591 - Medicaid Program; Withdrawal of Determination of Average Manufacturer Price, Multiple Source Drug...

    2010-11-15

    ..., Multiple Source Drug Definition, and Upper Limits for Multiple Source Drugs AGENCY: Centers for Medicare... withdrawing the definition of ``multiple source drug'' as it was revised in the ``Medicaid Program; Multiple Source Drug Definition'' final rule published in the October 7, 2008 Federal Register. DATES: Effective...

  17. Using National Drug Codes and drug knowledge bases to organize prescription records from multiple sources.

    Simonaitis, Linas; McDonald, Clement J

    2009-10-01

    The utility of National Drug Codes (NDCs) and drug knowledge bases (DKBs) in the organization of prescription records from multiple sources was studied. The master files of most pharmacy systems include NDCs and local codes to identify the products they dispense. We obtained a large sample of prescription records from seven different sources. These records carried a national product code or a local code that could be translated into a national product code via their formulary master. We obtained mapping tables from five DKBs. We measured the degree to which the DKB mapping tables covered the national product codes carried in or associated with the sample of prescription records. Considering the total prescription volume, DKBs covered 93.0-99.8% of the product codes from three outpatient sources and 77.4-97.0% of the product codes from four inpatient sources. Among the in-patient sources, invented codes explained 36-94% of the noncoverage. Outpatient pharmacy sources rarely invented codes, which comprised only 0.11-0.21% of their total prescription volume, compared with inpatient pharmacy sources for which invented codes comprised 1.7-7.4% of their prescription volume. The distribution of prescribed products was highly skewed, with 1.4-4.4% of codes accounting for 50% of the message volume and 10.7-34.5% accounting for 90% of the message volume. DKBs cover the product codes used by outpatient sources sufficiently well to permit automatic mapping. Changes in policies and standards could increase coverage of product codes used by inpatient sources.

  18. Multiple approaches to microbial source tracking in tropical northern Australia

    Neave, Matthew

    2014-09-16

    Microbial source tracking is an area of research in which multiple approaches are used to identify the sources of elevated bacterial concentrations in recreational lakes and beaches. At our study location in Darwin, northern Australia, water quality in the harbor is generally good, however dry-season beach closures due to elevated Escherichia coli and enterococci counts are a cause for concern. The sources of these high bacteria counts are currently unknown. To address this, we sampled sewage outfalls, other potential inputs, such as urban rivers and drains, and surrounding beaches, and used genetic fingerprints from E. coli and enterococci communities, fecal markers and 454 pyrosequencing to track contamination sources. A sewage effluent outfall (Larrakeyah discharge) was a source of bacteria, including fecal bacteria that impacted nearby beaches. Two other treated effluent discharges did not appear to influence sites other than those directly adjacent. Several beaches contained fecal indicator bacteria that likely originated from urban rivers and creeks within the catchment. Generally, connectivity between the sites was observed within distinct geographical locations and it appeared that most of the bacterial contamination on Darwin beaches was confined to local sources.

  19. Synergies of multiple remote sensing data sources for REDD+ monitoring

    Sy, de V.; Herold, M.; Achard, F.; Asner, G.P.; Held, A.; Kellndorfer, J.; Verbesselt, J.

    2012-01-01

    Remote sensing technologies can provide objective, practical and cost-effective solutions for developing and maintaining REDD+ monitoring systems. This paper reviews the potential and status of available remote sensing data sources with a focus on different forest information products and synergies

  20. Bioactive natural products from novel microbial sources.

    Challinor, Victoria L; Bode, Helge B

    2015-09-01

    Despite the importance of microbial natural products for human health, only a few bacterial genera have been mined for the new natural products needed to overcome the urgent threat of antibiotic resistance. This is surprising, given that genome sequencing projects have revealed that the capability to produce natural products is not a rare feature among bacteria. Even the bacteria occurring in the human microbiome produce potent antibiotics, and thus potentially are an untapped resource for novel compounds, potentially with new activities. This review highlights examples of bacteria that should be considered new sources of natural products, including anaerobes, pathogens, and symbionts of humans, insects, and nematodes. Exploitation of these producer strains, combined with advances in modern natural product research methodology, has the potential to open the way for a new golden age of microbial therapeutics. © 2015 New York Academy of Sciences.

  1. Investigating sources and pathways of perfluoroalkyl acids (PFAAs) in aquifers in Tokyo using multiple tracers

    Kuroda, Keisuke; Murakami, Michio; Oguma, Kumiko; Takada, Hideshige; Takizawa, Satoshi

    2014-01-01

    We employed a multi-tracer approach to investigate sources and pathways of perfluoroalkyl acids (PFAAs) in urban groundwater, based on 53 groundwater samples taken from confined aquifers and unconfined aquifers in Tokyo. While the median concentrations of groundwater PFAAs were several ng/L, the maximum concentrations of perfluorooctane sulfonate (PFOS, 990 ng/L), perfluorooctanoate (PFOA, 1800 ng/L) and perfluorononanoate (PFNA, 620 ng/L) in groundwater were several times higher than those of wastewater and street runoff reported in the literature. PFAAs were more frequently detected than sewage tracers (carbamazepine and crotamiton), presumably owing to the higher persistence of PFAAs, the multiple sources of PFAAs beyond sewage (e.g., surface runoff, point sources) and the formation of PFAAs from their precursors. Use of multiple methods of source apportionment including principal component analysis–multiple linear regression (PCA–MLR) and perfluoroalkyl carboxylic acid ratio analysis highlighted sewage and point sources as the primary sources of PFAAs in the most severely polluted groundwater samples, with street runoff being a minor source (44.6% sewage, 45.7% point sources and 9.7% street runoff, by PCA–MLR). Tritium analysis indicated that, while young groundwater (recharged during or after the 1970s, when PFAAs were already in commercial use) in shallow aquifers (< 50 m depth) was naturally highly vulnerable to PFAA pollution, PFAAs were also found in old groundwater (recharged before the 1950s, when PFAAs were not in use) in deep aquifers (50–500 m depth). This study demonstrated the utility of multiple uses of tracers (pharmaceuticals and personal care products; PPCPs, tritium) and source apportionment methods in investigating sources and pathways of PFAAs in multiple aquifer systems. - Highlights: • Aquifers in Tokyo had high levels of perfluoroalkyl acids (up to 1800 ng/L). • PFAAs were more frequently detected than sewage

  2. Investigating sources and pathways of perfluoroalkyl acids (PFAAs) in aquifers in Tokyo using multiple tracers

    Kuroda, Keisuke, E-mail: keisukekr@gmail.com [Department of Urban Engineering, Graduate School of Engineering, The University of Tokyo, 7-3-1 Hongo, Bunkyo, Tokyo 113-8656 (Japan); Murakami, Michio [Institute of Industrial Science, The University of Tokyo, 4-6-1 Komaba, Meguro, Tokyo 153-8505 (Japan); Oguma, Kumiko [Department of Urban Engineering, Graduate School of Engineering, The University of Tokyo, 7-3-1 Hongo, Bunkyo, Tokyo 113-8656 (Japan); Takada, Hideshige [Laboratory of Organic Geochemistry (LOG), Institute of Symbiotic Science and Technology, Tokyo University of Agriculture and Technology, Fuchu, Tokyo 183-8509 (Japan); Takizawa, Satoshi [Department of Urban Engineering, Graduate School of Engineering, The University of Tokyo, 7-3-1 Hongo, Bunkyo, Tokyo 113-8656 (Japan)

    2014-08-01

    We employed a multi-tracer approach to investigate sources and pathways of perfluoroalkyl acids (PFAAs) in urban groundwater, based on 53 groundwater samples taken from confined aquifers and unconfined aquifers in Tokyo. While the median concentrations of groundwater PFAAs were several ng/L, the maximum concentrations of perfluorooctane sulfonate (PFOS, 990 ng/L), perfluorooctanoate (PFOA, 1800 ng/L) and perfluorononanoate (PFNA, 620 ng/L) in groundwater were several times higher than those of wastewater and street runoff reported in the literature. PFAAs were more frequently detected than sewage tracers (carbamazepine and crotamiton), presumably owing to the higher persistence of PFAAs, the multiple sources of PFAAs beyond sewage (e.g., surface runoff, point sources) and the formation of PFAAs from their precursors. Use of multiple methods of source apportionment including principal component analysis–multiple linear regression (PCA–MLR) and perfluoroalkyl carboxylic acid ratio analysis highlighted sewage and point sources as the primary sources of PFAAs in the most severely polluted groundwater samples, with street runoff being a minor source (44.6% sewage, 45.7% point sources and 9.7% street runoff, by PCA–MLR). Tritium analysis indicated that, while young groundwater (recharged during or after the 1970s, when PFAAs were already in commercial use) in shallow aquifers (< 50 m depth) was naturally highly vulnerable to PFAA pollution, PFAAs were also found in old groundwater (recharged before the 1950s, when PFAAs were not in use) in deep aquifers (50–500 m depth). This study demonstrated the utility of multiple uses of tracers (pharmaceuticals and personal care products; PPCPs, tritium) and source apportionment methods in investigating sources and pathways of PFAAs in multiple aquifer systems. - Highlights: • Aquifers in Tokyo had high levels of perfluoroalkyl acids (up to 1800 ng/L). • PFAAs were more frequently detected than sewage

  3. Accommodating multiple illumination sources in an imaging colorimetry environment

    Tobin, Kenneth W., Jr.; Goddard, James S., Jr.; Hunt, Martin A.; Hylton, Kathy W.; Karnowski, Thomas P.; Simpson, Marc L.; Richards, Roger K.; Treece, Dale A.

    2000-03-01

    Researchers at the Oak Ridge National Laboratory have been developing a method for measuring color quality in textile products using a tri-stimulus color camera system. Initial results of the Imaging Tristimulus Colorimeter (ITC) were reported during 1999. These results showed that the projection onto convex sets (POCS) approach to color estimation could be applied to complex printed patterns on textile products with high accuracy and repeatability. Image-based color sensors used for on-line measurement are not colorimetric by nature and require a non-linear transformation of the component colors based on the spectral properties of the incident illumination, imaging sensor, and the actual textile color. Our earlier work reports these results for a broad-band, smoothly varying D65 standard illuminant. To move the measurement to the on-line environment with continuously manufactured textile webs, the illumination source becomes problematic. The spectral content of these light sources varies substantially from the D65 standard illuminant and can greatly impact the measurement performance of the POCS system. Although absolute color measurements are difficult to make under different illumination, referential measurements to monitor color drift provide a useful indication of product quality. Modifications to the ITC system have been implemented to enable the study of different light sources. These results and the subsequent analysis of relative color measurements will be reported for textile products.

  4. Localizing Brain Activity from Multiple Distinct Sources via EEG

    George Dassios

    2014-01-01

    Full Text Available An important question arousing in the framework of electroencephalography (EEG is the possibility to recognize, by means of a recorded surface potential, the number of activated areas in the brain. In the present paper, employing a homogeneous spherical conductor serving as an approximation of the brain, we provide a criterion which determines whether the measured surface potential is evoked by a single or multiple localized neuronal excitations. We show that the uniqueness of the inverse problem for a single dipole is closely connected with attaining certain relations connecting the measured data. Further, we present the necessary and sufficient conditions which decide whether the collected data originates from a single dipole or from numerous dipoles. In the case where the EEG data arouses from multiple parallel dipoles, an isolation of the source is, in general, not possible.

  5. Writing in the workplace: Constructing documents using multiple digital sources

    Mariëlle Leijten

    2014-02-01

    Full Text Available In today’s workplaces professional communication often involves constructing documents from multiple digital sources—integrating one’s own texts/graphics with ideas based on others’ text/graphics. This article presents a case study of a professional communication designer as he constructs a proposal over several days. Drawing on keystroke and interview data, we map the professional’s overall process, plot the time course of his writing/design, illustrate how he searches for content and switches among optional digital sources, and show how he modifies and reuses others’ content. The case study reveals not only that the professional (1 searches extensively through multiple sources for content and ideas but that he also (2 constructs visual content (charts, graphs, photographs as well as verbal content, and (3 manages his attention and motivation over this extended task. Since these three activities are not represented in current models of writing, we propose their addition not just to models of communication design, but also to models of writing in general.

  6. Production System Design for Multiple Brands

    Karlsson, Christer; Christensen, Irene

    Production systems enabling both cost efficiency and flexibility in terms of high product variation are explored. The study follows an explorative longitudinal field study approach. The database consists of three large global corporations, each consisting of several companies producing household ......-outs, worker skills, integration of distribution channels, after sales service and degree of servitization. Three production system design principles called VXY emerge....

  7. Interpretation of the TRADE In-Pile source multiplication experiments

    Mercatali, Luigi; Carta, Mario; Peluso, Vincenzo

    2006-01-01

    Within the framework of the neutronic characterization of the TRIGA RC-1 reactor in support to the TRADE (TRiga Accelerator Driven Experiment) program, the interpretation of the subcriticality level measurements performed in static regime during the TRADE In-Pile experimental program is presented. Different levels of subcriticality have been measured using the MSA (Modified Source Approximated) method by the insertion of a standard fixed radioactive source into different core positions. Starting from a reference configuration, fuel elements were removed: control rods were moved outward as required for the coupling experiments envisioned with the proton accelerator and fission chambers were inserted in order to measure subcritical count rates. A neutron-physics analysis based on the modified formulation of the source multiplication method (MSM) has been carried out, which requires the systematic solution for each experimental configuration of the homogeneous, both in the forward and adjoint forms, and inhomogeneous Boltzmann equations. By means of such a methodology calculated correction factors to be applied to the MSA measured reactivities were produced in order to take into account spatial and energetic effects creating changes in the detector efficiencies and effective source with respect to the calibration configuration. The methodology presented has been tested against a large number of experimental states. The measurements have underlined the sensitivity of the MSA measured reactivities to core geometry changes and control rod perturbations; the efficiency of MSM factors to dramatically correct for this sensitivity is underlined, making of this technique a relevant methodology in view of the incoming US RACE program to be performed in TRIGA reactors

  8. Negative binomial multiplicity distribution from binomial cluster production

    Iso, C.; Mori, K.

    1990-01-01

    Two-step interpretation of negative binomial multiplicity distribution as a compound of binomial cluster production and negative binomial like cluster decay distribution is proposed. In this model we can expect the average multiplicity for the cluster production increases with increasing energy, different from a compound Poisson-Logarithmic distribution. (orig.)

  9. Feature extraction from multiple data sources using genetic programming.

    Szymanski, J. J. (John J.); Brumby, Steven P.; Pope, P. A. (Paul A.); Eads, D. R. (Damian R.); Galassi, M. C. (Mark C.); Harvey, N. R. (Neal R.); Perkins, S. J. (Simon J.); Porter, R. B. (Reid B.); Theiler, J. P. (James P.); Young, A. C. (Aaron Cody); Bloch, J. J. (Jeffrey J.); David, N. A. (Nancy A.); Esch-Mosher, D. M. (Diana M.)

    2002-01-01

    Feature extration from imagery is an important and long-standing problem in remote sensing. In this paper, we report on work using genetic programming to perform feature extraction simultaneously from multispectral and digital elevation model (DEM) data. The tool used is the GENetic Imagery Exploitation (GENIE) software, which produces image-processing software that inherently combines spatial and spectral processing. GENIE is particularly useful in exploratory studies of imagery, such as one often does in combining data from multiple sources. The user trains the software by painting the feature of interest with a simple graphical user interface. GENIE then uses genetic programming techniques to produce an image-processing pipeline. Here, we demonstrate evolution of image processing algorithms that extract a range of land-cover features including towns, grasslands, wild fire burn scars, and several types of forest. We use imagery from the DOE/NNSA Multispectral Thermal Imager (MTI) spacecraft, fused with USGS 1:24000 scale DEM data.

  10. Multiple tobacco product use among US adolescents and young adults.

    Soneji, Samir; Sargent, James; Tanski, Susanne

    2016-03-01

    To assess the extent to which multiple tobacco product use among adolescents and young adults falls outside current Food and Drug Administration (FDA) regulatory authority. We conducted a web-based survey of 1596 16-26-year-olds to assess use of 11 types of tobacco products. We ascertained current (past 30 days) tobacco product use among 927 respondents who ever used tobacco. Combustible tobacco products included cigarettes, cigars (little filtered, cigarillos, premium) and hookah; non-combustible tobacco products included chew, dip, dissolvables, e-cigarettes, snuff and snus. We then fitted an ordinal logistic regression model to assess demographic and behavioural associations with higher levels of current tobacco product use (single, dual and multiple product use). Among 448 current tobacco users, 54% were single product users, 25% dual users and 21% multiple users. The largest single use category was cigarettes (49%), followed by hookah (23%), little filtered cigars (17%) and e-cigarettes (5%). Most dual and multiple product users smoked cigarettes, along with little filtered cigars, hookah and e-cigarettes. Forty-six per cent of current single, 84% of dual and 85% of multiple tobacco product users consumed a tobacco product outside FDA regulatory authority. In multivariable analysis, the adjusted risk of multiple tobacco use was higher for males, first use of a non-combustible tobacco product, high sensation seeking respondents and declined for each additional year of age that tobacco initiation was delayed. Nearly half of current adolescent and young adult tobacco users in this study engaged in dual and multiple tobacco product use; the majority of them used products that fall outside current FDA regulatory authority. This study supports FDA deeming of these products and their incorporation into the national media campaign to address youth tobacco use. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a

  11. Error Analysis of CM Data Products Sources of Uncertainty

    Hunt, Brian D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Eckert-Gallup, Aubrey Celia [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Cochran, Lainy Dromgoole [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Kraus, Terrence D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Allen, Mark B. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Beal, Bill [National Security Technologies, Joint Base Andrews, MD (United States); Okada, Colin [National Security Technologies, LLC. (NSTec), Las Vegas, NV (United States); Simpson, Mathew [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2017-02-01

    This goal of this project is to address the current inability to assess the overall error and uncertainty of data products developed and distributed by DOE’s Consequence Management (CM) Program. This is a widely recognized shortfall, the resolution of which would provide a great deal of value and defensibility to the analysis results, data products, and the decision making process that follows this work. A global approach to this problem is necessary because multiple sources of error and uncertainty contribute to the ultimate production of CM data products. Therefore, this project will require collaboration with subject matter experts across a wide range of FRMAC skill sets in order to quantify the types of uncertainty that each area of the CM process might contain and to understand how variations in these uncertainty sources contribute to the aggregated uncertainty present in CM data products. The ultimate goal of this project is to quantify the confidence level of CM products to ensure that appropriate public and worker protections decisions are supported by defensible analysis.

  12. Estimation of subcriticality by neutron source multiplication method

    Sakurai, Kiyoshi; Suzaki, Takenori; Arakawa, Takuya; Naito, Yoshitaka

    1995-03-01

    Subcritical cores were constructed in a core tank of the TCA by arraying 2.6% enriched UO 2 fuel rods into nxn square lattices of 1.956 cm pitch. Vertical distributions of the neutron count rates for the fifteen subcritical cores (n=17, 16, 14, 11, 8) with different water levels were measured at 5 cm interval with 235 U micro-fission counters at the in-core and out-core positions arranging a 252 C f neutron source at near core center. The continuous energy Monte Carlo code MCNP-4A was used for the calculation of neutron multiplication factors and neutron count rates. In this study, important conclusions are as follows: (1) Differences of neutron multiplication factors resulted from exponential experiment and MCNP-4A are below 1% in most cases. (2) Standard deviations of neutron count rates calculated from MCNP-4A with 500000 histories are 5-8%. The calculated neutron count rates are consistent with the measured one. (author)

  13. Assessing the use of multiple sources in student essays.

    Hastings, Peter; Hughes, Simon; Magliano, Joseph P; Goldman, Susan R; Lawless, Kimberly

    2012-09-01

    The present study explored different approaches for automatically scoring student essays that were written on the basis of multiple texts. Specifically, these approaches were developed to classify whether or not important elements of the texts were present in the essays. The first was a simple pattern-matching approach called "multi-word" that allowed for flexible matching of words and phrases in the sentences. The second technique was latent semantic analysis (LSA), which was used to compare student sentences to original source sentences using its high-dimensional vector-based representation. Finally, the third was a machine-learning technique, support vector machines, which learned a classification scheme from the corpus. The results of the study suggested that the LSA-based system was superior for detecting the presence of explicit content from the texts, but the multi-word pattern-matching approach was better for detecting inferences outside or across texts. These results suggest that the best approach for analyzing essays of this nature should draw upon multiple natural language processing approaches.

  14. Multiple time-reversed guide-sources in shallow water

    Gaumond, Charles F.; Fromm, David M.; Lingevitch, Joseph F.; Gauss, Roger C.; Menis, Richard

    2003-10-01

    Detection in a monostatic, broadband, active sonar system in shallow water is degraded by propagation-induced spreading. The detection improvement from multiple spatially separated guide sources (GSs) is presented as a method to mitigate this degradation. The improvement of detection by using information in a set of one-way transmissions from a variety of positions is shown using sea data. The experimental area is south of the Hudson Canyon off the coast of New Jersey. The data were taken using five elements of a time-reversing VLA. The five elements were contiguous and at midwater depth. The target and guide source was an echo repeater positioned at various ranges and at middepth. The transmitted signals were 3.0- to 3.5-kHz LFMs. The data are analyzed to show the amount of information present in the collection, a baseline probability of detection (PD) not using the collection of GS signals, the improvement in PD from the use of various sets of GS signals. The dependence of the improvement as a function of range is also shown. [The authors acknowledge support from Dr. Jeffrey Simmen, ONR321OS, and the chief scientist Dr. Charles Holland. Work supported by ONR.

  15. Testability evaluation using prior information of multiple sources

    Wang Chao

    2014-08-01

    Full Text Available Testability plays an important role in improving the readiness and decreasing the life-cycle cost of equipment. Testability demonstration and evaluation is of significance in measuring such testability indexes as fault detection rate (FDR and fault isolation rate (FIR, which is useful to the producer in mastering the testability level and improving the testability design, and helpful to the consumer in making purchase decisions. Aiming at the problems with a small sample of testability demonstration test data (TDTD such as low evaluation confidence and inaccurate result, a testability evaluation method is proposed based on the prior information of multiple sources and Bayes theory. Firstly, the types of prior information are analyzed. The maximum entropy method is applied to the prior information with the mean and interval estimate forms on the testability index to obtain the parameters of prior probability density function (PDF, and the empirical Bayesian method is used to get the parameters for the prior information with a success-fail form. Then, a parametrical data consistency check method is used to check the compatibility between all the sources of prior information and TDTD. For the prior information to pass the check, the prior credibility is calculated. A mixed prior distribution is formed based on the prior PDFs and the corresponding credibility. The Bayesian posterior distribution model is acquired with the mixed prior distribution and TDTD, based on which the point and interval estimates are calculated. Finally, examples of a flying control system are used to verify the proposed method. The results show that the proposed method is feasible and effective.

  16. Testability evaluation using prior information of multiple sources

    Wang Chao; Qiu Jing; Liu Guanjun; Zhang Yong

    2014-01-01

    Testability plays an important role in improving the readiness and decreasing the life-cycle cost of equipment. Testability demonstration and evaluation is of significance in measuring such testability indexes as fault detection rate (FDR) and fault isolation rate (FIR), which is useful to the producer in mastering the testability level and improving the testability design, and helpful to the consumer in making purchase decisions. Aiming at the problems with a small sample of testabil-ity demonstration test data (TDTD) such as low evaluation confidence and inaccurate result, a test-ability evaluation method is proposed based on the prior information of multiple sources and Bayes theory. Firstly, the types of prior information are analyzed. The maximum entropy method is applied to the prior information with the mean and interval estimate forms on the testability index to obtain the parameters of prior probability density function (PDF), and the empirical Bayesian method is used to get the parameters for the prior information with a success-fail form. Then, a parametrical data consistency check method is used to check the compatibility between all the sources of prior information and TDTD. For the prior information to pass the check, the prior credibility is calculated. A mixed prior distribution is formed based on the prior PDFs and the corresponding credibility. The Bayesian posterior distribution model is acquired with the mixed prior distribution and TDTD, based on which the point and interval estimates are calculated. Finally, examples of a flying control system are used to verify the proposed method. The results show that the proposed method is feasible and effective.

  17. Multiple-linac approach for tritium production and other applications

    Ruggiero, A.G.

    1995-01-01

    This report describes an approach to tritium production based on the use of multiple proton linear accelerators. Features of a single APTT Linac as proposed by the Los Alamos National Laboratory are presented and discussed. An alternative approach to the attainment of the same total proton beam power of 200 MW with several lower-performance superconducting Linacs is proposed and discussed. Although each of these accelerators are considerable extrapolations of present technology, the latter can nevertheless be built at less technical risk when compared to the single high-current APT Linac, particularly concerning the design and the performance of the low-energy front-end. The use of superconducting cavities is also proposed as a way of optimizing the accelerating gradient, the overall length, and the operational costs. The superconducting technology has already been successfully demonstrated in a number of large-size projects and should be seriously considered for the acceleration of intense low-energy beams of protons. Finally, each linear accelerator would represent an ideal source of very intense beams of protons for a variety of applications, such as: weapons and waste actinide transmutation processes, isotopes for medical application, spallation neutron sources, and the generation of intense beams of neutrinos and muons for nuclear and high-energy physics research. The research community at large has obviously an interest in providing expertise for, and in having access to, the demonstration, the construction, the operation, and the exploitation of these top-performance accelerators

  18. Production of highly charged ion beams from ECR ion sources

    Xie, Z.Q.

    1997-09-01

    Electron Cyclotron Resonance (ECR) ion source development has progressed with multiple-frequency plasma heating, higher mirror magnetic fields and better technique to provide extra cold electrons. Such techniques greatly enhance the production of highly charged ions from ECR ion sources. So far at cw mode operation, up to 300 eμA of O 7+ and 1.15 emA of O 6+ , more than 100 eμA of intermediate heavy ions for charge states up to Ar 13+ , Ca 13+ , Fe 13+ , Co 14+ and Kr 18+ , and tens of eμA of heavy ions with charge states to Kr 26+ , Xe 28+ , Au 35+ , Bi 34+ and U 34+ have been produced from ECR ion sources. At an intensity of at least 1 eμA, the maximum charge state available for the heavy ions are Xe 36+ , Au 46+ , Bi 47+ and U 48+ . An order of magnitude enhancement for fully stripped argon ions (I ≥ 60 enA) also has been achieved. This article will review the ECR ion source progress and discuss key requirement for ECR ion sources to produce the highly charged ion beams

  19. Microfluidic production of multiple emulsions and functional microcapsules

    Lee, Tae Yong; Choi, Tae Min; Shim, Tae Soup; Frijns, Raoul A.M.; Kim, Shin Hyun

    2016-01-01

    Recent advances in microfluidics have enabled the controlled production of multiple-emulsion drops with onion-like topology. The multiple-emulsion drops possess an intrinsic core-shell geometry, which makes them useful as templates to create microcapsules with a solid membrane. High flexibility

  20. Analysis of a production/inventory system with multiple retailers

    Noblesse, Ann; Boute, Robert; Lambrecht, Marc; Van Houdt, B.

    2014-01-01

    We study a production/inventory system with one manufacturing plant and multiple retailers. Production lead times at the plant are stochastic and endogenously determined by the orders placed by the different retailers. Assuming stochastic (phase-type distributed) production and setup times, we make use of matrix analytic techniques to develop a queuing model that is capable to compute the distribution of the time orders spend in the production facility, depending on the retailer’s lot s...

  1. Iridium-192 sources production for brachytherapy use

    Rostelato, Maria Elisa Chuery Martins

    1997-01-01

    The incidence of cancer increases every year in Brazil and turns out to be one of the most important causes of mortality. Some of the patients are treated with brachytherapy, a form of lesion treatment which is based on the insertion of sources into tumors, in this particular case, activated iridium wires. During this process, the ionizing radiation efficiently destroys the malignant cells. These iridium wires have a nucleus made out of an iridium-platinum alloy 20-30/70-80 of 0,1 mm in diameter either coated by platinum or encased in a platinum tube. The technique consists in irradiating the wire in the reactor neutron flux in order to produce iridium-192. The linear activity goes from 1 mCi/cm to 4 mCi/cm and the basic characteristic, which is required, is the homogeneity of the activation along the wire. It should not present a dispersion exceeding 5% on a wire measuring 50 cm in length, 0.5 mm or 0.3 mm in diameter. Several experiments were carried out in order to define the activation parameters. Wires from different origins were analyzed. It was concluded that United States of America and France wires were found to be perfectly adequate for brachytherapy purposes and have therefore been sent to specialized hospitals and successfully applied to cancer patients. Considering that the major purpose of this work is to make this product more accessible in Brazil, at a cost reflecting the Brazilian reality, the IPEN is promoting the preparation of iridium-192 sources to be used in brachytherapy, on a national level. (author)

  2. Fontes de energia em suplementos múltiplos para bezerros Nelore em creep-feeding: desempenho produtivo, consumo e digestibilidade dos nutrientes Energy sources in multiple supplements for Nellore calves in creep-feeding: productive performance, nutrient intake and digestibility

    Marlos Oliveira Porto

    2009-07-01

    were evaluated. The area was divided into five 6.8 ha paddocks with an availability of dry matter and potentially digestible dry matter of 4.10 and 2.38 t/ha, respectively. Forty-five animals with 96.0 ± 11.0 kg initial weight and 101 ± 12 days of age were allotted to a completely randomized experimental design, as a 5 × 2 factorial (five supplements and two sex. The following supplements were evaluated: mineral mix (MM, control group; soybean meal (SM + ground corn grain (GCG and mineral mix; soybean meal + wheat meal + ground corn grain and mineral mix; soybean meal + rice meal and mineral mix; soybean meal + ground sorghum grain + ground corn grain and mineral mix; supplied daily at the amount of 60 g/animal for the control group and 500 g for the other diets, respectively. There was statistical significance for the animals that received supplementation with ground corn grain and ground sorghum grain that showed an additional average daily gain of 100 g (16.39% higher than the animals that received only mineral mix. The use of multiple supplements based on ground sorghum grain and corn grain increased dry matter intake and forage organic matter more than the diet with ground corn grain. The supplementation with energy sources with ground sorghum grain and corn grain can provide additional average daily gain and increase in forage intake, in animals in creep-feeding.

  3. Cumulative effect in multiple production processes on nuclei

    Golubyatnikova, E.S.; Shmonin, V.L.; Kalinkin, B.N.

    1989-01-01

    It is shown that the cumulative effect is a natural result of the process of hadron multiple production in nuclear reactions. Interpretation is made of the universality of slopes of inclusive spectra and other characteristics of cumulative hadrons. The character of information from such reactions is discussed, which could be helpful in studying the mechanism of multiparticle production. 27 refs.; 4 figs

  4. Tensor rank is not multiplicative under the tensor product

    Christandl, Matthias; Jensen, Asger Kjærulff; Zuiddam, Jeroen

    2017-01-01

    The tensor rank of a tensor t is the smallest number r such that t can be decomposed as a sum of r simple tensors. Let s be a k-tensor and let t be an l-tensor. The tensor product of s and t is a (k + l)-tensor. Tensor rank is sub-multiplicative under the tensor product. We revisit the connection between restrictions and degenerations. A result of our study is that tensor rank is not in general multiplicative under the tensor product. This answers a question of Draisma and Saptharishi. Specif...

  5. Joint Dynamic Pricing of Multiple Perishable Products Under Consumer Choice

    Yalç{\\i}n Akçay; Harihara Prasad Natarajan; Susan H. Xu

    2010-01-01

    In response to competitive pressures, firms are increasingly adopting revenue management opportunities afforded by advances in information and communication technologies. Motivated by these revenue management initiatives in industry, we consider a dynamic pricing problem facing a firm that sells given initial inventories of multiple substitutable and perishable products over a finite selling horizon. Because the products are substitutable, individual product demands are linked through consume...

  6. Neutron generators with size scalability, ease of fabrication and multiple ion source functionalities

    Elizondo-Decanini, Juan M

    2014-11-18

    A neutron generator is provided with a flat, rectilinear geometry and surface mounted metallizations. This construction provides scalability and ease of fabrication, and permits multiple ion source functionalities.

  7. Relationship between exposure to multiple noise sources and noise annoyance

    Miedema, H.M.E.

    2004-01-01

    Relationships between exposure to noise [metric: day-night level (DNL) or day-evening-night level (DENL)] from a single source (aircraft, road traffic, or railways) and annoyance based on a large international dataset have been published earlier. Also for stationary sources relationships have been

  8. Effect of failures and repairs on multiple cell production lines

    Legato, P.; Bobbio, A.; Roberti, L.

    1989-01-01

    This paper examines a production line composed of multiple stages, or cells, which are passed in sequential order to arrive to the final product. Two possible coordination disciplines are considered, namely: the classical tandem arrangement of sequential working centers with input buffer and the kanban scheme, considered the Japanese shop floor realization of the Just-In-Time (JIT) manifacturing approach. The production line is modelled and analysed by means of Stochastic Petri Nets (SPN). Finally an analysis is made of the possibility that the working cells can incur failure/repair cycles perturbing the production flow of the line and thus reduce performance indices.

  9. Modeling water demand when households have multiple sources of water

    Coulibaly, Lassina; Jakus, Paul M.; Keith, John E.

    2014-07-01

    A significant portion of the world's population lives in areas where public water delivery systems are unreliable and/or deliver poor quality water. In response, people have developed important alternatives to publicly supplied water. To date, most water demand research has been based on single-equation models for a single source of water, with very few studies that have examined water demand from two sources of water (where all nonpublic system water sources have been aggregated into a single demand). This modeling approach leads to two outcomes. First, the demand models do not capture the full range of alternatives, so the true economic relationship among the alternatives is obscured. Second, and more seriously, economic theory predicts that demand for a good becomes more price-elastic as the number of close substitutes increases. If researchers artificially limit the number of alternatives studied to something less than the true number, the price elasticity estimate may be biased downward. This paper examines water demand in a region with near universal access to piped water, but where system reliability and quality is such that many alternative sources of water exist. In extending the demand analysis to four sources of water, we are able to (i) demonstrate why households choose the water sources they do, (ii) provide a richer description of the demand relationships among sources, and (iii) calculate own-price elasticity estimates that are more elastic than those generally found in the literature.

  10. Multiple station beamline at an undulator x-ray source

    Als-Nielsen, J.; Freund, A.K.; Grübel, G.

    1994-01-01

    The undulator X-ray source is an ideal source for many applications: the beam is brilliant, highly collimated in all directions, quasi-monochromatic, pulsed and linearly polarized. Such a precious source can feed several independently operated instruments by utilizing a downstream series of X......-ray transparent monochromator crystals. Diamond in particular is an attractive monochromator as it is rather X-ray transparent and can be fabricated to a high degree of crystal perfection. Moreover, it has a very high heat conductivity and a rather small thermal expansion so the beam X-ray heat load problem...

  11. Multiplicity distributions in a thermodynamical model of hadron production in e+e- collisions

    Becattini, F.; Giovannini, A.; Lupia, S.

    1996-01-01

    Predictions of a thermodynamical model of hadron production for multiplicity distributions in e + e - annihilations at LEP and PEP-PETRA centre of mass energies are shown. The production process is described as a two-step process in which primary hadrons emitted from the thermal source decay into final observable particles. The final charged track multiplicity distributions turn out to be of negative binomial type and are in quite good agreement with experimental observations. The average number of clans calculated from fitted negative binomial coincides with the average number of primary hadrons predicted by the thermodynamical model, suggesting that clans should be identified with primary hadrons. (orig.)

  12. Multiple approaches to microbial source tracking in tropical northern Australia

    Neave, Matthew; Luter, Heidi; Padovan, Anna; Townsend, Simon; Schobben, Xavier; Gibb, Karen

    2014-01-01

    , other potential inputs, such as urban rivers and drains, and surrounding beaches, and used genetic fingerprints from E. coli and enterococci communities, fecal markers and 454 pyrosequencing to track contamination sources. A sewage effluent outfall

  13. Tensor rank is not multiplicative under the tensor product

    Christandl, Matthias; Jensen, Asger Kjærulff; Zuiddam, Jeroen

    2018-01-01

    The tensor rank of a tensor t is the smallest number r such that t can be decomposed as a sum of r simple tensors. Let s be a k-tensor and let t be an ℓ-tensor. The tensor product of s and t is a (k+ℓ)-tensor. Tensor rank is sub-multiplicative under the tensor product. We revisit the connection b...

  14. Tensor rank is not multiplicative under the tensor product

    M. Christandl (Matthias); A. K. Jensen (Asger Kjærulff); J. Zuiddam (Jeroen)

    2018-01-01

    textabstractThe tensor rank of a tensor t is the smallest number r such that t can be decomposed as a sum of r simple tensors. Let s be a k-tensor and let t be an ℓ-tensor. The tensor product of s and t is a (k+ℓ)-tensor. Tensor rank is sub-multiplicative under the tensor product. We revisit the

  15. SACHET, Dynamic Fission Products Inventory in PWR Multiple Compartment System

    Kodaira, Hideki

    1990-01-01

    1 - Description of program or function: SACHET evaluates the dynamic fission product inventories in the multiple compartment system of pressurized water reactor (PWR) plants. 2 - Method of solution: SACHET utilizes a matrix of fission product core inventory which is previously calculated by the ORIGEN code. 3 - Restrictions on the complexity of the problem: Liquid wastes such as chemical waste and detergent waste are not included

  16. Analysis of oil-pipeline distribution of multiple products subject to delivery time-windows

    Jittamai, Phongchai

    This dissertation defines the operational problems of, and develops solution methodologies for, a distribution of multiple products into oil pipeline subject to delivery time-windows constraints. A multiple-product oil pipeline is a pipeline system composing of pipes, pumps, valves and storage facilities used to transport different types of liquids. Typically, products delivered by pipelines are petroleum of different grades moving either from production facilities to refineries or from refineries to distributors. Time-windows, which are generally used in logistics and scheduling areas, are incorporated in this study. The distribution of multiple products into oil pipeline subject to delivery time-windows is modeled as multicommodity network flow structure and mathematically formulated. The main focus of this dissertation is the investigation of operating issues and problem complexity of single-source pipeline problems and also providing solution methodology to compute input schedule that yields minimum total time violation from due delivery time-windows. The problem is proved to be NP-complete. The heuristic approach, a reversed-flow algorithm, is developed based on pipeline flow reversibility to compute input schedule for the pipeline problem. This algorithm is implemented in no longer than O(T·E) time. This dissertation also extends the study to examine some operating attributes and problem complexity of multiple-source pipelines. The multiple-source pipeline problem is also NP-complete. A heuristic algorithm modified from the one used in single-source pipeline problems is introduced. This algorithm can also be implemented in no longer than O(T·E) time. Computational results are presented for both methodologies on randomly generated problem sets. The computational experience indicates that reversed-flow algorithms provide good solutions in comparison with the optimal solutions. Only 25% of the problems tested were more than 30% greater than optimal values and

  17. Metasurface Cloak Performance Near-by Multiple Line Sources and PEC Cylindrical Objects

    Arslanagic, Samel; Yatman, William H.; Pehrson, Signe

    2014-01-01

    The performance/robustness of metasurface cloaks to a complex field environment which may represent a realistic scenario of radiating sources is presently reported. Attention is devoted to the cloak operation near-by multiple line sources and multiple perfectly electrically conducting cylinders. ...

  18. Energy production from renewable energy sources

    2001-04-01

    This table summarizes the electricity and heat produced in France and in overseas departments from renewable energy sources for 1998 (revised), 1999 (temporary) and 2000 (estimated): hydraulic, wind, solar photovoltaic and thermal, geothermal, solid municipal wastes, wood and wood wastes, biogas, ethanol and ester bio-fuels. (J.S.)

  19. Speculative Attacks with Multiple Sources of Public Information

    Cornand, Camille; Heinemann, Frank

    2005-01-01

    We propose a speculative attack model in which agents receive multiple public signals. It is characterised by its focus on an informational structure, which sets free from the strict separation between public information and private information. Diverse pieces of public information can be taken into account differently by players and are likely to lead to different appreciations ex post. This process defines players’ private value. The main result is to show that equilibrium uniqueness depend...

  20. Multiple-source multiple-harmonic active vibration control of variable section cylindrical structures: A numerical study

    Liu, Jinxin; Chen, Xuefeng; Gao, Jiawei; Zhang, Xingwu

    2016-12-01

    Air vehicles, space vehicles and underwater vehicles, the cabins of which can be viewed as variable section cylindrical structures, have multiple rotational vibration sources (e.g., engines, propellers, compressors and motors), making the spectrum of noise multiple-harmonic. The suppression of such noise has been a focus of interests in the field of active vibration control (AVC). In this paper, a multiple-source multiple-harmonic (MSMH) active vibration suppression algorithm with feed-forward structure is proposed based on reference amplitude rectification and conjugate gradient method (CGM). An AVC simulation scheme called finite element model in-loop simulation (FEMILS) is also proposed for rapid algorithm verification. Numerical studies of AVC are conducted on a variable section cylindrical structure based on the proposed MSMH algorithm and FEMILS scheme. It can be seen from the numerical studies that: (1) the proposed MSMH algorithm can individually suppress each component of the multiple-harmonic noise with an unified and improved convergence rate; (2) the FEMILS scheme is convenient and straightforward for multiple-source simulations with an acceptable loop time. Moreover, the simulations have similar procedure to real-life control and can be easily extended to physical model platform.

  1. Radioactive waste management in sealed sources laboratory production

    Carvalho, Gilberto

    2001-01-01

    The laboratory of sealed sources production, of Instituto de Pesquisas Energeticas e Nucleares, was created in 1983 and since then, has produced radioactive sources for industry and engineering in general, having specialization in assembly of radiation sources for non destructive testings, by gammagraphy, with Iridium-192, that represents 98% of the production of laboratory and 2% with the Cobalt-60, used in nuclear gages. The aim of this work, is to quantify and qualify the radioactive wastes generated annually, taking into account, the average of radioactive sources produced, that are approximately 220 sources per year

  2. PUBLIC EXPOSURE TO MULTIPLE RF SOURCES IN GHANA.

    Deatanyah, P; Abavare, E K K; Menyeh, A; Amoako, J K

    2018-03-16

    This paper describes an effort to respond to the suggestion in World Health Organization (WHO) research agenda to better quantify potential exposure levels from a range of radiofrequency (RF) sources at 200 public access locations in Ghana. Wide-band measurements were performed-with a spectrum analyser and a log-periodic antenna using three-point spatial averaging method. The overall results represented a maximum of 0.19% of the ICNIRP reference levels for public exposure. These results were generally lower than found in some previous but were 58% (2.0 dB) greater, than found in similar work conducted in the USA. Major contributing sources of RF fields were identified to be FM broadcast and mobile base station sites. Three locations with the greatest measured RF fields could represent potential areas for epidemiological studies.

  3. Correlations in multiple production on nuclei and Glauber model of multiple scattering

    Zoller, V.R.; Nikolaev, N.N.

    1982-01-01

    Critical analysis of possibility for describing correlation phenomena during multiple production on nuclei within the framework of the Glauber multiple seattering model generalized for particle production processes with Capella, Krziwinski and Shabelsky has been performed. It was mainly concluded that the suggested generalization of the Glauber model gives dependences on Ng(Np) (where Ng-the number of ''grey'' tracess, and Np-the number of protons flying out of nucleus) and, eventually, on #betta# (where #betta#-the number of intranuclear interactions) contradicting experience. Independent of choice of relation between #betta# and Ng(Np) in the model the rapidity corrletor Rsub(eta) is overstated in the central region and understated in the region of nucleus fragmentation. In mean multiplicities these two contradictions of experience are disguised with random compensation and agreement with experience in Nsub(S) (function of Ng) cannot be an argument in favour of the model. It is concluded that eiconal model doesn't permit to quantitatively describe correlation phenomena during the multiple production on nuclei

  4. Multiple sources of boron in urban surface waters and groundwaters

    Hasenmueller, Elizabeth A., E-mail: eahasenm@wustl.edu; Criss, Robert E.

    2013-03-01

    Previous studies attribute abnormal boron (B) levels in streams and groundwaters to wastewater and fertilizer inputs. This study shows that municipal drinking water used for lawn irrigation contributes substantial non-point loads of B and other chemicals (S-species, Li, and Cu) to surface waters and shallow groundwaters in the St. Louis, Missouri, area. Background levels and potential B sources were characterized by analysis of lawn and street runoff, streams, rivers, springs, local rainfall, wastewater influent and effluent, and fertilizers. Urban surface waters and groundwaters are highly enriched in B (to 250 μg/L) compared to background levels found in rain and pristine, carbonate-hosted streams and springs (< 25 μg/L), but have similar concentrations (150 to 259 μg/L) compared to municipal drinking waters derived from the Missouri River. Other data including B/SO{sub 4}{sup 2-}−S and B/Li ratios confirm major contributions from this source. Moreover, sequential samples of runoff collected during storms show that B concentrations decrease with increased discharge, proving that elevated B levels are not primarily derived from combined sewer overflows (CSOs) during flooding. Instead, non-point source B exhibits complex behavior depending on land use. In urban settings B is rapidly mobilized from lawns during “first flush” events, likely representing surficial salt residues from drinking water used to irrigate lawns, and is also associated with the baseflow fraction, likely derived from the shallow groundwater reservoir that over time accumulates B from drinking water that percolates into the subsurface. The opposite occurs in small rural watersheds, where B is leached from soils by recent rainfall and covaries with the event water fraction. Highlights: ► Boron sources and loads differ between urban and rural watersheds. ► Wastewaters are not the major boron source in small St. Louis, MO watersheds. ► Municipal drinking water used for lawn

  5. Geothermal Energy as source or energy production

    Lozano, E.

    1998-01-01

    This article shows the use and utilization of geothermal energy. This calorific energy can be used, through the wells perforation, in generation of electricity and many other tasks. In Colombia is possible the utilization of this energy in the electrical production due to the volcanic presence in the Western and Central mountain chains

  6. Providing context: antimicrobial resistance from multiple environmental sources

    Background: Animal agriculture has been identified as encouraging the spread of resistance due to the use of large quantities of antimicrobials for animal production purposes. When antimicrobial resistance (AMR) is reported in agricultural settings without comparison to other environments there is a...

  7. Optimizing Irrigation Water Allocation under Multiple Sources of Uncertainty in an Arid River Basin

    Wei, Y.; Tang, D.; Gao, H.; Ding, Y.

    2015-12-01

    Population growth and climate change add additional pressures affecting water resources management strategies for meeting demands from different economic sectors. It is especially challenging in arid regions where fresh water is limited. For instance, in the Tailanhe River Basin (Xinjiang, China), a compromise must be made between water suppliers and users during drought years. This study presents a multi-objective irrigation water allocation model to cope with water scarcity in arid river basins. To deal with the uncertainties from multiple sources in the water allocation system (e.g., variations of available water amount, crop yield, crop prices, and water price), the model employs a interval linear programming approach. The multi-objective optimization model developed from this study is characterized by integrating eco-system service theory into water-saving measures. For evaluation purposes, the model is used to construct an optimal allocation system for irrigation areas fed by the Tailan River (Xinjiang Province, China). The objective functions to be optimized are formulated based on these irrigation areas' economic, social, and ecological benefits. The optimal irrigation water allocation plans are made under different hydroclimate conditions (wet year, normal year, and dry year), with multiple sources of uncertainty represented. The modeling tool and results are valuable for advising decision making by the local water authority—and the agricultural community—especially on measures for coping with water scarcity (by incorporating uncertain factors associated with crop production planning).

  8. Antiparticle sources for antihydrogen production and trapping

    Charlton, M.; Bruun Andresen, Gorm; Ashkezari, M. D.

    2011-01-01

    Sources of positrons and antiprotons that are currently used for the formation of antihydrogen with low kinetic energies are reviewed, mostly in the context of the ALPHA collaboration and its predecessor ATHENA. The experiments were undertaken at the Antiproton Decelerator facility, which...... is located at CERN. Operations performed on the clouds of antiparticles to facilitate their mixing to produce antihydrogen are described. These include accumulation, cooling and manipulation. The formation of antihydrogen and some of the characteristics of the anti-atoms that are created are discussed....... Prospects for trapping antihydrogen in a magnetic minimum trap, as envisaged by the ALPHA collaboration, are reviewed....

  9. Antiparticle sources for antihydrogen production and trapping

    Charlton, M; Bertsche, W; Butler, E; Humphries, A J [Department of Physics, Swansea University, Swansea SA2 8PP (United Kingdom); Andresen, G B; Bowe, P D; Hangst, J S [Department of Physics and Astronomy, Aarhus University, DK-8000 Aarhus C (Denmark); Ashkezari, M D; Hayden, M E [Department of Physics, Simon Fraser University, Burnaby BC, V5A 1S6 (Canada); Baquero-Ruiz, M; Bray, C C; Chapman, S; Fajans, J [Department of Physics, University of California, Berkeley, CA 94720-7300 (United States); Cesar, C L [Instituto de Fisica, Universidade Federal do Rio de Janeiro, Rio de Janeiro 21941-972 (Brazil); Friesen, T; Hydomako, R [Department of Physics and Astronomy, University of Calgary, Calgary AB, T2N 1N4 (Canada); Fujiwara, M C; Gill, D R [TRIUMF, 4004 Wesbrook Mall, Vancouver BC, V6T 2A3 (Canada); Hardy, W N [Department of Physics and Astronomy, University of British Columbia, Vancouver BC, V6T 1Z4 (Canada); Hayano, R S, E-mail: M.Charlton@Swansea.ac.uk [Department of Physics, University of Tokyo, Tokyo 113-0033 (Japan)

    2011-12-01

    Sources of positrons and antiprotons that are currently used for the formation of antihydrogen with low kinetic energies are reviewed, mostly in the context of the ALPHA collaboration and its predecessor ATHENA. The experiments were undertaken at the Antiproton Decelerator facility, which is located at CERN. Operations performed on the clouds of antiparticles to facilitate their mixing to produce antihydrogen are described. These include accumulation, cooling and manipulation. The formation of antihydrogen and some of the characteristics of the anti-atoms that are created are discussed. Prospects for trapping antihydrogen in a magnetic minimum trap, as envisaged by the ALPHA collaboration, are reviewed.

  10. Some problems of neutron source multiplication method for site measurement technology in nuclear critical safety

    Shi Yongqian; Zhu Qingfu; Hu Dingsheng; He Tao; Yao Shigui; Lin Shenghuo

    2004-01-01

    The paper gives experiment theory and experiment method of neutron source multiplication method for site measurement technology in the nuclear critical safety. The measured parameter by source multiplication method actually is a sub-critical with source neutron effective multiplication factor k s , but not the neutron effective multiplication factor k eff . The experiment research has been done on the uranium solution nuclear critical safety experiment assembly. The k s of different sub-criticality is measured by neutron source multiplication experiment method, and k eff of different sub-criticality, the reactivity coefficient of unit solution level, is first measured by period method, and then multiplied by difference of critical solution level and sub-critical solution level and obtained the reactivity of sub-critical solution level. The k eff finally can be extracted from reactivity formula. The effect on the nuclear critical safety and different between k eff and k s are discussed

  11. Multiple Sources of Prescription Payment and Risky Opioid Therapy Among Veterans.

    Becker, William C; Fenton, Brenda T; Brandt, Cynthia A; Doyle, Erin L; Francis, Joseph; Goulet, Joseph L; Moore, Brent A; Torrise, Virginia; Kerns, Robert D; Kreiner, Peter W

    2017-07-01

    Opioid overdose and other related harms are a major source of morbidity and mortality among US Veterans, in part due to high-risk opioid prescribing. We sought to determine whether having multiple sources of payment for opioids-as a marker for out-of-system access-is associated with risky opioid therapy among veterans. Cross-sectional study examining the association between multiple sources of payment and risky opioid therapy among all individuals with Veterans Health Administration (VHA) payment for opioid analgesic prescriptions in Kentucky during fiscal year 2014-2015. Source of payment categories: (1) VHA only source of payment (sole source); (2) sources of payment were VHA and at least 1 cash payment [VHA+cash payment(s)] whether or not there was a third source of payment; and (3) at least one other noncash source: Medicare, Medicaid, or private insurance [VHA+noncash source(s)]. Our outcomes were 2 risky opioid therapies: combination opioid/benzodiazepine therapy and high-dose opioid therapy, defined as morphine equivalent daily dose ≥90 mg. Of the 14,795 individuals in the analytic sample, there were 81.9% in the sole source category, 6.6% in the VHA+cash payment(s) category, and 11.5% in the VHA+noncash source(s) category. In logistic regression, controlling for age and sex, persons with multiple payment sources had significantly higher odds of each risky opioid therapy, with those in the VHA+cash having significantly higher odds than those in the VHA+noncash source(s) group. Prescribers should examine the prescription monitoring program as multiple payment sources increase the odds of risky opioid therapy.

  12. Multiple Household Water Sources and Their Use in Remote Communities With Evidence From Pacific Island Countries

    Elliott, Mark; MacDonald, Morgan C.; Chan, Terence; Kearton, Annika; Shields, Katherine F.; Bartram, Jamie K.; Hadwen, Wade L.

    2017-11-01

    Global water research and monitoring typically focus on the household's "main source of drinking-water." Use of multiple water sources to meet daily household needs has been noted in many developing countries but rarely quantified or reported in detail. We gathered self-reported data using a cross-sectional survey of 405 households in eight communities of the Republic of the Marshall Islands (RMI) and five Solomon Islands (SI) communities. Over 90% of households used multiple sources, with differences in sources and uses between wet and dry seasons. Most RMI households had large rainwater tanks and rationed stored rainwater for drinking throughout the dry season, whereas most SI households collected rainwater in small pots, precluding storage across seasons. Use of a source for cooking was strongly positively correlated with use for drinking, whereas use for cooking was negatively correlated or uncorrelated with nonconsumptive uses (e.g., bathing). Dry season water uses implied greater risk of water-borne disease, with fewer (frequently zero) handwashing sources reported and more unimproved sources consumed. Use of multiple sources is fundamental to household water management and feasible to monitor using electronic survey tools. We contend that recognizing multiple water sources can greatly improve understanding of household-level and community-level climate change resilience, that use of multiple sources confounds health impact studies of water interventions, and that incorporating multiple sources into water supply interventions can yield heretofore-unrealized benefits. We propose that failure to consider multiple sources undermines the design and effectiveness of global water monitoring, data interpretation, implementation, policy, and research.

  13. Production of jet fuel from alternative source

    Eller, Zoltan; Papp, Anita; Hancsok, Jenoe [Pannonia Univ., Veszprem (Hungary). MOL Dept. of Hydrocarbon and Coal Processing

    2013-06-01

    Recent demands for low aromatic content jet fuels have shown significant increase in the last 20 years. This was generated by the growing of aviation. Furthermore, the quality requirements have become more aggravated for jet fuels. Nowadays reduced aromatic hydrocarbon fractions are necessary for the production of jet fuels with good burning properties, which contribute to less harmful material emission. In the recent past the properties of gasolines and diesel gas oils were continuously severed, and the properties of jet fuels will be more severe, too. Furthermore, it can become obligatory to blend alternative components into jet fuels. With the aromatic content reduction there is a possibility to produce high energy content jet fuels with the desirable properties. One of the possibilities is the blending of biocomponents from catalytic hydrogenation of triglycerides. Our aim was to study the possibilities of producing low sulphur and aromatic content jet fuels in a catalytic way. On a CoMo/Al{sub 2}O{sub 3} catalyst we studied the possibilities of quality improving of a kerosene fraction and coconut oil mixture depending on the change of the process parameters (temperature, pressure, liquid hourly space velocity, volume ratio). Based on the quality parameters of the liquid products we found that we made from the feedstock in the adequate technological conditions products which have a high smoke point (> 35 mm) and which have reduced aromatic content and high paraffin content (90%), so these are excellent jet fuels, and their stack gases damage the environment less. (orig.)

  14. Sources of Information as Determinants of Product and Process Innovation.

    Gómez, Jaime; Salazar, Idana; Vargas, Pilar

    2016-01-01

    In this paper we use a panel of manufacturing firms in Spain to examine the extent to which they use internal and external sources of information (customers, suppliers, competitors, consultants and universities) to generate product and process innovation. Our results show that, although internal sources are influential, external sources of information are key to achieve innovation performance. These results are in line with the open innovation literature because they show that firms that are opening up their innovation process and that use different information sources have a greater capacity to generate innovations. We also find that the importance of external sources of information varies depending on the type of innovation (product or process) considered. To generate process innovation, firms mainly rely on suppliers while, to generate product innovation, the main contribution is from customers. The potential simultaneity between product and process innovation is also taken into consideration. We find that the generation of both types of innovation is not independent.

  15. Sources of Information as Determinants of Product and Process Innovation.

    Jaime Gómez

    Full Text Available In this paper we use a panel of manufacturing firms in Spain to examine the extent to which they use internal and external sources of information (customers, suppliers, competitors, consultants and universities to generate product and process innovation. Our results show that, although internal sources are influential, external sources of information are key to achieve innovation performance. These results are in line with the open innovation literature because they show that firms that are opening up their innovation process and that use different information sources have a greater capacity to generate innovations. We also find that the importance of external sources of information varies depending on the type of innovation (product or process considered. To generate process innovation, firms mainly rely on suppliers while, to generate product innovation, the main contribution is from customers. The potential simultaneity between product and process innovation is also taken into consideration. We find that the generation of both types of innovation is not independent.

  16. Sources of Information as Determinants of Product and Process Innovation

    2016-01-01

    In this paper we use a panel of manufacturing firms in Spain to examine the extent to which they use internal and external sources of information (customers, suppliers, competitors, consultants and universities) to generate product and process innovation. Our results show that, although internal sources are influential, external sources of information are key to achieve innovation performance. These results are in line with the open innovation literature because they show that firms that are opening up their innovation process and that use different information sources have a greater capacity to generate innovations. We also find that the importance of external sources of information varies depending on the type of innovation (product or process) considered. To generate process innovation, firms mainly rely on suppliers while, to generate product innovation, the main contribution is from customers. The potential simultaneity between product and process innovation is also taken into consideration. We find that the generation of both types of innovation is not independent. PMID:27035456

  17. Primary energy sources for hydrogen production

    Hassmann, K.; Kuehne, H.M.

    1993-01-01

    The costs for hydrogen production through water electrolysis are estimated, assuming the electricity is produced from solar, hydro-, fossil, or nuclear power. The costs for hydrogen end-use in the power generation, heat and transportation sectors are also calculated, based on a state of the art technology and a more advanced technology expected to represent the state by the year 2010. The costs for hydrogen utilization (without energy taxes) are shown to be higher than current prices for fossil fuels (including taxes). Without restrictions imposed on fossil fuel consumption, hydrogen shall not gain a significant market share in either of the cases discussed. 2 figs., 3 tabs., 4 refs

  18. Effective sourcing strategies for perishable product supply chains

    Rijpkema, W.A.; Rossi, R.; Vorst, van der J.G.A.J.

    2014-01-01

    Purpose – The purpose of this paper is to assess whether an existing sourcing strategy can effectively supply products of appropriate quality with acceptable levels of product waste if applied to an international perishable product supply chain. The authors also analyse whether the effectiveness of

  19. A robust poverty profile for Brazil using multiple data sources

    Ferreira Francisco H. G.

    2003-01-01

    Full Text Available This paper presents a poverty profile for Brazil, based on three different sources of household data for 1996. We use PPV consumption data to estimate poverty and indigence lines. ''Contagem'' data is used to allow for an unprecedented refinement of the country's poverty map. Poverty measures and shares are also presented for a wide range of population subgroups, based on the PNAD 1996, with new adjustments for imputed rents and spatial differences in cost of living. Robustness of the profile is verified with respect to different poverty lines, spatial price deflators, and equivalence scales. Overall poverty incidence ranges from 23% with respect to an indigence line to 45% with respect to a more generous poverty line. More importantly, however, poverty is found to vary significantly across regions and city sizes, with rural areas, small and medium towns and the metropolitan peripheries of the North and Northeast regions being poorest.

  20. Exploiting semantic linkages among multiple sources for semantic information retrieval

    Li, JianQiang; Yang, Ji-Jiang; Liu, Chunchen; Zhao, Yu; Liu, Bo; Shi, Yuliang

    2014-07-01

    The vision of the Semantic Web is to build a global Web of machine-readable data to be consumed by intelligent applications. As the first step to make this vision come true, the initiative of linked open data has fostered many novel applications aimed at improving data accessibility in the public Web. Comparably, the enterprise environment is so different from the public Web that most potentially usable business information originates in an unstructured form (typically in free text), which poses a challenge for the adoption of semantic technologies in the enterprise environment. Considering that the business information in a company is highly specific and centred around a set of commonly used concepts, this paper describes a pilot study to migrate the concept of linked data into the development of a domain-specific application, i.e. the vehicle repair support system. The set of commonly used concepts, including the part name of a car and the phenomenon term on the car repairing, are employed to build the linkage between data and documents distributed among different sources, leading to the fusion of documents and data across source boundaries. Then, we describe the approaches of semantic information retrieval to consume these linkages for value creation for companies. The experiments on two real-world data sets show that the proposed approaches outperform the best baseline 6.3-10.8% and 6.4-11.1% in terms of top five and top 10 precisions, respectively. We believe that our pilot study can serve as an important reference for the development of similar semantic applications in an enterprise environment.

  1. Search Strategy of Detector Position For Neutron Source Multiplication Method by Using Detected-Neutron Multiplication Factor

    Endo, Tomohiro

    2011-01-01

    In this paper, an alternative definition of a neutron multiplication factor, detected-neutron multiplication factor kdet, is produced for the neutron source multiplication method..(NSM). By using kdet, a search strategy of appropriate detector position for NSM is also proposed. The NSM is one of the practical subcritical measurement techniques, i.e., the NSM does not require any special equipment other than a stationary external neutron source and an ordinary neutron detector. Additionally, the NSM method is based on steady-state analysis, so that this technique is very suitable for quasi real-time measurement. It is noted that the correction factors play important roles in order to accurately estimate subcriticality from the measured neutron count rates. The present paper aims to clarify how to correct the subcriticality measured by the NSM method, the physical meaning of the correction factors, and how to reduce the impact of correction factors by setting a neutron detector at an appropriate detector position

  2. Multiple electromagnetic pair production in ultrarelativistic heavy ion collisions

    Best, C.

    1992-04-01

    The problem of the unitary violation in the pair production in ultrarelativistic heavy ion collisions was studied by a consideration of the field-theoretical foundations. The quantum electrodynamics in an external field were thereby reduced to a Dirac-sea model, the equivalence of which to the non-radiative QED resulted from the equality of the generating functionals. The latter can both be expressed explicitely by means of the complet set of the solutions of the Dirac equation in an external field. This method is based solely on the path-integral approach, which makes it possible to discriminate clearly between the physically given correlation functions and their generating functional at the one hand and at the other hand between the models constructed to their interpretation. From the model expression for the pair production amplitudes and multiplicities could be calculated, for which only the knowledge of the one-particle S matrix is necessary. For the calculation of the multiplicities different forms of the perturbation theory were discussed. Finally an impact-parameter dependent Weizsaecker-Williams approximation for the calculation of arbitrary two-photon graphs was constructed and applied to the given problem. The results indicate that at small distances very high pair multiplicities are to be expected. Finally a new approach to the pair production in an external field was discussed, which is not based on the canonical field theory, but on the formalism of the Wigner functions. (orig./HSI) [de

  3. Assessing regional groundwater stress for nations using multiple data sources with the groundwater footprint

    Gleeson, Tom; Wada, Yoshihide

    2013-01-01

    Groundwater is a critical resource for agricultural production, ecosystems, drinking water and industry, yet groundwater depletion is accelerating, especially in a number of agriculturally important regions. Assessing the stress of groundwater resources is crucial for science-based policy and management, yet water stress assessments have often neglected groundwater and used single data sources, which may underestimate the uncertainty of the assessment. We consistently analyze and interpret groundwater stress across whole nations using multiple data sources for the first time. We focus on two nations with the highest national groundwater abstraction rates in the world, the United States and India, and use the recently developed groundwater footprint and multiple datasets of groundwater recharge and withdrawal derived from hydrologic models and data synthesis. A minority of aquifers, mostly with known groundwater depletion, show groundwater stress regardless of the input dataset. The majority of aquifers are not stressed with any input data while less than a third are stressed for some input data. In both countries groundwater stress affects agriculturally important regions. In the United States, groundwater stress impacts a lower proportion of the national area and population, and is focused in regions with lower population and water well density compared to India. Importantly, the results indicate that the uncertainty is generally greater between datasets than within datasets and that much of the uncertainty is due to recharge estimates. Assessment of groundwater stress consistently across a nation and assessment of uncertainty using multiple datasets are critical for the development of a science-based rationale for policy and management, especially with regard to where and to what extent to focus limited research and management resources. (letter)

  4. Sources of water column methylmercury across multiple estuaries in the Northeast U.S.

    Balcom, Prentiss H; Schartup, Amina T; Mason, Robert P; Chen, Celia Y

    2015-12-20

    Estuarine water column methylmercury (MeHg) is an important driver of mercury (Hg) bioaccumulation in pelagic organisms and thus it is necessary to understand the sources and processes affecting environmental levels of MeHg. Increases in water column MeHg concentrations can ultimately be transferred to fish consumed by humans, but despite this, the sources of MeHg to the estuarine water column are still poorly understood. Here we evaluate MeHg sources across 4 estuaries and 10 sampling sites and examine the distributions and partitioning of sediment and water column MeHg across a geographic range (Maine to New Jersey). Our study sites present a gradient in the concentrations of sediment, pore water and water column Hg species. Suspended particle MeHg ranged from below detection to 187 pmol g -1 , dissolved MeHg from 0.01 to 0.68 pM, and sediment MeHg from 0.01 to 109 pmol g -1 . Across multiple estuaries, dissolved MeHg correlated with Hg species in the water column, and sediment MeHg correlated with sediment total Hg (HgT). Water column MeHg did not correlate well with sediment Hg across estuaries, indicating that sediment concentrations were not a good predictor of water MeHg concentrations. This is an unexpected finding since it has been shown that MeHg production from inorganic Hg 2+ within sediment is the primary source of MeHg to coastal waters. Additional sources of MeHg regulate water column MeHg levels in some of the shallow estuaries included in this study.

  5. Design, development and integration of a large scale multiple source X-ray computed tomography system

    Malcolm, Andrew A.; Liu, Tong; Ng, Ivan Kee Beng; Teng, Wei Yuen; Yap, Tsi Tung; Wan, Siew Ping; Kong, Chun Jeng

    2013-01-01

    X-ray Computed Tomography (CT) allows visualisation of the physical structures in the interior of an object without physically opening or cutting it. This technology supports a wide range of applications in the non-destructive testing, failure analysis or performance evaluation of industrial products and components. Of the numerous factors that influence the performance characteristics of an X-ray CT system the energy level in the X-ray spectrum to be used is one of the most significant. The ability of the X-ray beam to penetrate a given thickness of a specific material is directly related to the maximum available energy level in the beam. Higher energy levels allow penetration of thicker components made of more dense materials. In response to local industry demand and in support of on-going research activity in the area of 3D X-ray imaging for industrial inspection the Singapore Institute of Manufacturing Technology (SIMTech) engaged in the design, development and integration of large scale multiple source X-ray computed tomography system based on X-ray sources operating at higher energies than previously available in the Institute. The system consists of a large area direct digital X-ray detector (410 x 410 mm), a multiple-axis manipulator system, a 225 kV open tube microfocus X-ray source and a 450 kV closed tube millifocus X-ray source. The 225 kV X-ray source can be operated in either transmission or reflection mode. The body of the 6-axis manipulator system is fabricated from heavy-duty steel onto which high precision linear and rotary motors have been mounted in order to achieve high accuracy, stability and repeatability. A source-detector distance of up to 2.5 m can be achieved. The system is controlled by a proprietary X-ray CT operating system developed by SIMTech. The system currently can accommodate samples up to 0.5 x 0.5 x 0.5 m in size with weight up to 50 kg. These specifications will be increased to 1.0 x 1.0 x 1.0 m and 100 kg in future

  6. Bryophytes - an emerging source for herbal remedies and chemical production

    Sabovljevic, Marko S.; Sabovljević, Aneta D.; Ikram, Nur Kusaira K.

    2016-01-01

    biomass in various ecosystems, bryophytes are a seldom part of ethnomedicine and rarely subject to medicinal and chemical analyses. Still, hundreds of novel natural products have been isolated from bryophytes. Bryophytes have been shown to contain numerous potentially useful natural products, including...... loss, plant growth regulators and allelopathic activities. Bryophytes also cause allergies and contact dermatitis. All these effects highlight bryophytes as potential source for herbal remedies and production of chemicals to be used in various products....

  7. Sources of Combustion Products: An Introduction to Indoor Air Quality

    In addition to environmental tobacco smoke, other sources of combustion products are unvented kerosene and gas space heaters, woodstoves, fireplaces, and gas stoves. The major pollutants released are carbon monoxide, nitrogen dioxide, and particles.

  8. Regularity of optimal transport maps on multiple products of spheres

    Figalli, Alessio; Kim, Young-Heon; McCann, Robert J.

    2010-01-01

    This article addresses regularity of optimal transport maps for cost="squared distance" on Riemannian manifolds that are products of arbitrarily many round spheres with arbitrary sizes and dimensions. Such manifolds are known to be non-negatively cross-curved [KM2]. Under boundedness and non-vanishing assumptions on the transfered source and target densities we show that optimal maps stay away from the cut-locus (where the cost exhibits singularity), and obtain injectivity and continuity of o...

  9. Joint part-of-speech and dependency projection from multiple sources

    Johannsen, Anders Trærup; Agic, Zeljko; Søgaard, Anders

    2016-01-01

    for multiple tasks from multiple source languages, relying on parallel corpora available for hundreds of languages. When training POS taggers and dependency parsers on jointly projected POS tags and syntactic dependencies using our algorithm, we obtain better performance than a standard approach on 20...

  10. Sources of Information as Determinants of Product and Process Innovation

    G?mez, Jaime; Salazar, Idana; Vargas, Pilar

    2016-01-01

    In this paper we use a panel of manufacturing firms in Spain to examine the extent to which they use internal and external sources of information (customers, suppliers, competitors, consultants and universities) to generate product and process innovation. Our results show that, although internal sources are influential, external sources of information are key to achieve innovation performance. These results are in line with the open innovation literature because they show that firms that are ...

  11. Genetic diversity and antimicrobial resistance of Escherichia coli from human and animal sources uncovers multiple resistances from human sources.

    A Mark Ibekwe

    Full Text Available Escherichia coli are widely used as indicators of fecal contamination, and in some cases to identify host sources of fecal contamination in surface water. Prevalence, genetic diversity and antimicrobial susceptibility were determined for 600 generic E. coli isolates obtained from surface water and sediment from creeks and channels along the middle Santa Ana River (MSAR watershed of southern California, USA, after a 12 month study. Evaluation of E. coli populations along the creeks and channels showed that E. coli were more prevalent in sediment compared to surface water. E. coli populations were not significantly different (P = 0.05 between urban runoff sources and agricultural sources, however, E. coli genotypes determined by pulsed-field gel electrophoresis (PFGE were less diverse in the agricultural sources than in urban runoff sources. PFGE also showed that E. coli populations in surface water were more diverse than in the sediment, suggesting isolates in sediment may be dominated by clonal populations.Twenty four percent (144 isolates of the 600 isolates exhibited resistance to more than one antimicrobial agent. Most multiple resistances were associated with inputs from urban runoff and involved the antimicrobials rifampicin, tetracycline, and erythromycin. The occurrence of a greater number of E. coli with multiple antibiotic resistances from urban runoff sources than agricultural sources in this watershed provides useful evidence in planning strategies for water quality management and public health protection.

  12. The effect of energy distribution of external source on source multiplication in fast assemblies

    Karam, R.A.; Vakilian, M.

    1976-02-01

    The essence of this study is the effect of energy distribution of a source on the detection rate as a function of K effective in fast assemblies. This effectiveness, as a function of K was studied in a fission chamber, using the ABN cross-section set and Mach 1 code. It was found that with a source which has a fission spectrum, the reciprocal count rate versus mass relationship is linear down to K effective 0.59. For a thermal source, the linearity was never achieved. (author)

  13. Influence of multiple bioprocess parameters on production of lipase from Pseudomonas sp. BWS-5

    Balwinder Singh Sooch

    2013-10-01

    Full Text Available The aim of the present work was to study the influence of multiple bioprocess parameters for the maximum production of lipase from Pseudomonas sp. BWS-5. The culture reached the stationary phase of growth after 36h of incubation when the maximum lipase production was obtained at flask level. The different media components such as carbon sources, nitrogen sources, trace elements and process parameters such as the pH of the medium, temperature and time of incubation, agitation/stationary conditions, etc. were optimized at flask level and at bioreactor level. The maximum enzyme production of 298 IU/mL was obtained with the use of simple medium with pH 6.5 containing glucose (1 %, w/v, peptone (3 %, w/v and KCl (0.05 %, w/v after 30h of incubation at 37°C under agitation (200 rpm conditions with 0.75 vvm of air supply.

  14. An economic production model for time dependent demand with rework and multiple production setups

    S.R. Singh

    2014-04-01

    Full Text Available In this paper, we present a model for time dependent demand with multiple productions and rework setups. Production is demand dependent and greater than the demand rate. Production facility produces items in m production setups and one rework setup (m, 1 policy. The major reason of reverse logistic and green supply chain is rework, so it reduces the cost of production and other ecological problems. Most of the researchers developed a rework model without deteriorating items. A numerical example and sensitivity analysis is shown to describe the model.

  15. Multiple vacancy production by high energy heavy ions

    Becker, R.L.; Ford, A.L.; Reading, J.F.

    1984-01-01

    The theory of atomic collisions has two ingredients: collision theory and atomic structure theory. The collision theories differ with respect to (A) the collision dynamics and (B) the treatment of the relative motion of the projectile and target nuclei. With regard to the dynamics multiple vacancy production is of fundamental interest because it is a signature for and probe of strong interactions between the projectile and the target electrons. For projectiles of large nuclear charge, Z/sub p/, especially for those which are highly stripped so as to have a large ionic charge, q, the interaction becomes strong enough to give a high probability of multiple vacancy production and a breakdown of perturbation theory. The familiar first and second Born approximations and their off-shoots cease to be adequate. Not even the recent strong-potential Born approximation (see Taulbjerg 1984) is sufficient, because the weaker of the potentials generated by the projectile and the target nuclei, respectively, is treated in first order. One needs a unitary, non-perturbative collision theory. At present this is generally available for multiple vacancy production only in the form of the highly numerical coupled channels theory (Becker et al. 1983, 1984b). For special problems analytically tractable models have been devised. For example, a simple, unitary, geometrical encounter probability model for the calculation of p/sub L/(0), the inclusive L-shell vacancy probability per electron in collisions with impact parameter B = 0, has been introduced by Sulik et al. (1984) and further developed by Sulik and Hock (1984). Along with earlier coupled-channels calculations (Becker et al. 1984ab) and first Magnus calculations (Becker et al. 1984b), this model is able to describe the saturation of p/sub L/(0) with Z/sub p/ at fixed impact speed, v, whereas all the first-order theories predict p/sub L/ proportional to Z/sub p/ 2 , which eventually exceeds unity

  16. Economic feasibility constraints for renewable energy source power production

    Biondi, L.

    1992-01-01

    Suitable analysis criteria for use in economic feasibility studies of renewable energy source power plants are examined for various plant types, e.g., pumped storage hydroelectric, geothermal, wind, solar, refuse-fuelled, etc. The paper focusses on the impacts, on operating cost and rate structure, of the necessity, depending on demand characteristics, to integrate renewable energy source power production with conventional power production in order to effectively and economically meet peak power demand. The influence of commercialization and marketing trends on renewable energy source power plant economic feasibility are also taken into consideration

  17. Fission product source term research at Oak Ridge National Laboratory

    Malinauskas, A.P.

    1985-01-01

    The purpose of this work is to describe some of the research being performed at ORNL in support of the effort to describe, as realistically as possible, fission product source terms for nuclear reactor accidents. In order to make this presentation manageable, only those studies directly concerned with fission product behavior, as opposed to thermal hydraulics, accident sequence progression, etc., will be discussed

  18. Analysis of Product Sampling for New Product Diffusion Incorporating Multiple-Unit Ownership

    Zhineng Hu

    2014-01-01

    Full Text Available Multiple-unit ownership of nondurable products is an important component of sales in many product categories. Based on the Bass model, this paper develops a new model considering the multiple-unit adoptions as a diffusion process under the influence of product sampling. Though the analysis aims to determine the optimal dynamic sampling effort for a firm and the results demonstrate that experience sampling can accelerate the diffusion process, the best time to send free samples is just before the product being launched. Multiple-unit purchasing behavior can increase sales to make more profit for a firm, and it needs more samples to make the product known much better. The local sensitivity analysis shows that the increase of both external coefficients and internal coefficients has a negative influence on the sampling level, but the internal influence on the subsequent multiple-unit adoptions has little significant influence on the sampling. Using the logistic regression along with linear regression, the global sensitivity analysis gives a whole analysis of the interaction of all factors, which manifests the external influence and multiunit purchase rate are two most important factors to influence the sampling level and net present value of the new product, and presents a two-stage method to determine the sampling level.

  19. Industrial open source solutions for product life cycle management

    Jaime Campos

    2014-12-01

    Full Text Available The authors go through the open source for product life cycle management (PLM and the efforts done from communities such as the open source initiative. The characteristics of the open source solutions are highlighted as well. Next, the authors go through the requirements for PLM. This is an area where more attention has been given as the manufacturers are competing with the quality and life cycle costs of their products. Especially, the need of companies to try to get a strong position in providing services for their products and thus to make themselves less vulnerable to changes in the market has led to high interest in product life cycle simulation. The potential of applying semantic data management to solve these problems discussed in the light of recent developments. In addition, a basic roadmap is presented as to how the above-described problems could be tackled with open software solutions.

  20. Radioactive sealed sources production process for industrial radiography

    Santos, Paulo de S.; Ngunga, Daniel M.G.; Camara, Julio R.; Vasquez, Pablo A.S.

    2017-01-01

    providing products and services to the private and governmental Brazilian users of industrial radiography and nucleonic control systems. Radioactive sealed sources are commonly used in nondestructive tests as radiography to make inspections and verify the internal structure and integrity of materials and in nucleonic gauges to control level, density, viscosity, etc. in on-line industrial processes. One of the most important activities carried out by this laboratory is related to the inspection of source projectors devices used in industrial radiography and its constituent parts as well as remote handle control assembly drive cable and guide tube systems. The laboratory also provide for the users iridium-192, cobalt-60 and selenium-75 sealed sources and performs quality control tests replacing spent or contaminated radiative sources. All discard of radioactive source is treated as radioactive waste. Additionally, administrative and commercial processes and protocols for exportation and transport of radioactive material are developed by specialized departments. In this work are presented the mean processes and procedures used by the Sealed Source Production Laboratory such as the arrival of the radioactive material to the laboratory and the source projectors, mechanical inspections, source loading, source leaking tests, etc. (author)

  1. Radioactive sealed sources production process for industrial radiography

    Santos, Paulo de S.; Ngunga, Daniel M.G.; Camara, Julio R.; Vasquez, Pablo A.S., E-mail: psantos@ipen.br, E-mail: hobeddaniel@gmail.com, E-mail: jrcamara@ipen.br, E-mail: pavsalva@ipen.br [Instituto de Pesquisas Energética s e Nucleares (IPEN/CNEN-SP), São Paulo, SP (Brazil)

    2017-07-01

    providing products and services to the private and governmental Brazilian users of industrial radiography and nucleonic control systems. Radioactive sealed sources are commonly used in nondestructive tests as radiography to make inspections and verify the internal structure and integrity of materials and in nucleonic gauges to control level, density, viscosity, etc. in on-line industrial processes. One of the most important activities carried out by this laboratory is related to the inspection of source projectors devices used in industrial radiography and its constituent parts as well as remote handle control assembly drive cable and guide tube systems. The laboratory also provide for the users iridium-192, cobalt-60 and selenium-75 sealed sources and performs quality control tests replacing spent or contaminated radiative sources. All discard of radioactive source is treated as radioactive waste. Additionally, administrative and commercial processes and protocols for exportation and transport of radioactive material are developed by specialized departments. In this work are presented the mean processes and procedures used by the Sealed Source Production Laboratory such as the arrival of the radioactive material to the laboratory and the source projectors, mechanical inspections, source loading, source leaking tests, etc. (author)

  2. Integrated Production-Distribution Scheduling Problem with Multiple Independent Manufacturers

    Jianhong Hao

    2015-01-01

    Full Text Available We consider the nonstandard parts supply chain with a public service platform for machinery integration in China. The platform assigns orders placed by a machinery enterprise to multiple independent manufacturers who produce nonstandard parts and makes production schedule and batch delivery schedule for each manufacturer in a coordinate manner. Each manufacturer has only one plant with parallel machines and is located at a location far away from other manufacturers. Orders are first processed at the plants and then directly shipped from the plants to the enterprise in order to be finished before a given deadline. We study the above integrated production-distribution scheduling problem with multiple manufacturers to maximize a weight sum of the profit of each manufacturer under the constraints that all orders are finished before the deadline and the profit of each manufacturer is not negative. According to the optimal condition analysis, we formulate the problem as a mixed integer programming model and use CPLEX to solve it.

  3. Community Response to Multiple Sound Sources: Integrating Acoustic and Contextual Approaches in the Analysis

    Peter Lercher

    2017-06-01

    Full Text Available Sufficient data refer to the relevant prevalence of sound exposure by mixed traffic sources in many nations. Furthermore, consideration of the potential effects of combined sound exposure is required in legal procedures such as environmental health impact assessments. Nevertheless, current practice still uses single exposure response functions. It is silently assumed that those standard exposure-response curves accommodate also for mixed exposures—although some evidence from experimental and field studies casts doubt on this practice. The ALPNAP-study population (N = 1641 shows sufficient subgroups with combinations of rail-highway, highway-main road and rail-highway-main road sound exposure. In this paper we apply a few suggested approaches of the literature to investigate exposure-response curves and its major determinants in the case of exposure to multiple traffic sources. Highly/moderate annoyance and full scale mean annoyance served as outcome. The results show several limitations of the current approaches. Even facing the inherent methodological limitations (energy equivalent summation of sound, rating of overall annoyance the consideration of main contextual factors jointly occurring with the sources (such as vibration, air pollution or coping activities and judgments of the wider area soundscape increases the variance explanation from up to 8% (bivariate, up to 15% (base adjustments up to 55% (full contextual model. The added predictors vary significantly, depending on the source combination. (e.g., significant vibration effects with main road/railway, not highway. Although no significant interactions were found, the observed additive effects are of public health importance. Especially in the case of a three source exposure situation the overall annoyance is already high at lower levels and the contribution of the acoustic indicators is small compared with the non-acoustic and contextual predictors. Noise mapping needs to go down to

  4. Multiple cues for winged morph production in an aphid metacommunity.

    Mohsen Mehrparvar

    Full Text Available Environmental factors can lead individuals down different developmental pathways giving rise to distinct phenotypes (phenotypic plasticity. The production of winged or unwinged morphs in aphids is an example of two alternative developmental pathways. Dispersal is paramount in aphids that often have a metapopulation structure, where local subpopulations frequently go extinct, such as the specialized aphids on tansy (Tanacetum vulgare. We conducted various experiments to further understand the cues involved in the production of winged dispersal morphs by the two dominant species of the tansy aphid metacommunity, Metopeurum fuscoviride and Macrosiphoniella tanacetaria. We found that the ant-tended M. fuscoviride produced winged individuals predominantly at the beginning of the season while the untended M. tanacetaria produced winged individuals throughout the season. Winged mothers of both species produced winged offspring, although in both species winged offspring were mainly produced by unwinged females. Crowding and the presence of predators, effects already known to influence wing production in other aphid species, increased the percentage of winged offspring in M. tanacetaria, but not in M. fuscoviride. We find there are also other factors (i.e. temporal effects inducing the production of winged offspring for natural aphid populations. Our results show that the responses of each aphid species are due to multiple wing induction cues.

  5. Journey of a Package: Category 1 Source (Co-60) Shipment with Several Border Crossings, Multiple Modes

    Gray, P. A.

    2016-01-01

    Radioactive materials (RAM) are used extensively in a vast array of industries and in an even wider breadth of applications on a truly global basis each and every day. Over the past 50 years, these applications and the quantity (activity) of RAM shipped has grown significantly, with the next 50 years expected to show a continuing trend. The movement of these goods occurs in all regions of the world, and must therefore be conducted in a manner which will not adversely impact people or the environment. Industry and regulators have jointly met this challenge, so much so that RAM shipments are amongst the safest of any product. How has this level of performance been achieved? What is involved in shipping RAM from one corner of the world to another, often via a number of in-transit locations and often utilizing multiple modes of transport in any single shipment? This paper reviews one such journey, of Category 1 Cobalt-60 sources, as they move from point of manufacture through to point of use including the detailed and multi-approval process, the stringent regulatory requirements in place, the extensive communications required throughout, and the practical aspects needed to simply offer such a product for sale and transport. Upon completion, the rationale for such an exemplary safety and security record will be readily apparent. (author)

  6. Smoke production from multiple nuclear explosions in nonurban areas

    Small, R.D.; Bush, B.W.

    1985-01-01

    The amount of smoke that may be produced by wildland or rural fires as a consequence of a large-scale nuclear exchange is estimated. The calculation is based on a compilation of rural military facilities, identified from a wide variety of unclassified sources, together with data on their geographic positions, surrounding vegetation (fuel), and weather conditions. The ignition area (corrected for fuel moisture) and the amount of fire spread are used to calculate the smoke production. The results show a substantially lower estimated smoke production (from wildland fires) than in earlier nuclear winter studies. The amount varies seasonally and at its peak is less by an order of magnitude than the estimated threshold level necessary for a major attenuation of solar radiation. 32 references, 6 figures, 2 tables

  7. Multiple finances, margins of foreign direct investment and aggregate industry productivity

    Jiarui Zhang

    2012-03-01

    Full Text Available Based on a heterogeneous firm set-up, we model firms’ access to the internal capital market, bank finance as well as bond finance and investigate how firms’ adjustment among multiple sources of finance affects their performance in foreign direct investment and aggregate industry productivity. We find that when facing a bank credit shock (e.g. tighter bank lending, firms with different productivities react differently. Less productive firms exit from the foreign market due to a lack of funds while the more productive resort to bond finance to sustain their multinational status. The increased demand for bond finance as compensation for decreased bank finance by the surviving multinationals exacerbates the competition in the bond market and bids up the bond return rate, which triggers a Melitz-type selection effect through the bond market and brings aggregate industry gains.However, the divestment of those failing FDI firms and the consequently reduced bond financing demand mitigate this effect.

  8. Observational constraints on the physical nature of submillimetre source multiplicity: chance projections are common

    Hayward, Christopher C.; Chapman, Scott C.; Steidel, Charles C.; Golob, Anneya; Casey, Caitlin M.; Smith, Daniel J. B.; Zitrin, Adi; Blain, Andrew W.; Bremer, Malcolm N.; Chen, Chian-Chou; Coppin, Kristen E. K.; Farrah, Duncan; Ibar, Eduardo; Michałowski, Michał J.; Sawicki, Marcin; Scott, Douglas; van der Werf, Paul; Fazio, Giovanni G.; Geach, James E.; Gurwell, Mark; Petitpas, Glen; Wilner, David J.

    2018-05-01

    Interferometric observations have demonstrated that a significant fraction of single-dish submillimetre (submm) sources are blends of multiple submm galaxies (SMGs), but the nature of this multiplicity, i.e. whether the galaxies are physically associated or chance projections, has not been determined. We performed spectroscopy of 11 SMGs in six multicomponent submm sources, obtaining spectroscopic redshifts for nine of them. For an additional two component SMGs, we detected continuum emission but no obvious features. We supplement our observed sources with four single-dish submm sources from the literature. This sample allows us to statistically constrain the physical nature of single-dish submm source multiplicity for the first time. In three (3/7, { or} 43^{+39 }_{ -33} {per cent at 95 {per cent} confidence}) of the single-dish sources for which the nature of the blending is unambiguous, the components for which spectroscopic redshifts are available are physically associated, whereas 4/7 (57^{+33 }_{ -39} per cent) have at least one unassociated component. When components whose spectra exhibit continuum but no features and for which the photometric redshift is significantly different from the spectroscopic redshift of the other component are also considered, 6/9 (67^{+26 }_{ -37} per cent) of the single-dish sources are comprised of at least one unassociated component SMG. The nature of the multiplicity of one single-dish source is ambiguous. We conclude that physically associated systems and chance projections both contribute to the multicomponent single-dish submm source population. This result contradicts the conventional wisdom that bright submm sources are solely a result of merger-induced starbursts, as blending of unassociated galaxies is also important.

  9. End-of-life flows of multiple cycle consumer products

    Tsiliyannis, C.A.

    2011-01-01

    Explicit expressions for the end-of-life flows (EOL) of single and multiple cycle products (MCPs) are presented, including deterministic and stochastic EOL exit. The expressions are given in terms of the physical parameters (maximum lifetime, T, annual cycling frequency, f, number of cycles, N, and early discard or usage loss). EOL flows are also obtained for hi-tech products, which are rapidly renewed and thus may not attain steady state (e.g. electronic products, passenger cars). A ten-step recursive procedure for obtaining the dynamic EOL flow evolution is proposed. Applications of the EOL expressions and the ten-step procedure are given for electric household appliances, industrial machinery, tyres, vehicles and buildings, both for deterministic and stochastic EOL exit, (normal, Weibull and uniform exit distributions). The effect of the physical parameters and the stochastic characteristics on the EOL flow is investigated in the examples: it is shown that the EOL flow profile is determined primarily by the early discard dynamics; it also depends strongly on longevity and cycling frequency: higher lifetime or early discard/loss imply lower dynamic and steady state EOL flows. The stochastic exit shapes the overall EOL dynamic profile: Under symmetric EOL exit distribution, as the variance of the distribution increases (uniform to normal to deterministic) the initial EOL flow rise becomes steeper but the steady state or maximum EOL flow level is lower. The steepest EOL flow profile, featuring the highest steady state or maximum level, as well, corresponds to skew, earlier shifted EOL exit (e.g. Weibull). Since the EOL flow of returned products consists the sink of the reuse/remanufacturing cycle (sink to recycle) the results may be used in closed loop product lifecycle management operations for scheduling and sizing reverse manufacturing and for planning recycle logistics. Decoupling and quantification of both the full age EOL and of the early discard flows is

  10. Medicinal herbs as possible sources of anti-inflammatory products

    Andreia Corciovă

    2017-12-01

    Full Text Available Plants constitute an inexhaustible source of bioactive compounds that can be valuable for research in the chemistry field of anti-inflammatory compounds. This review describes several plants from international and national flora that have been shown to have anti-inflammatory activity in various clinical trials. The paper includes: general aspects regarding the vegetal source, compounds responsible for anti-inflammatory activity, mechanism of action and clinical trials carried out with extracts or products containing standardized extracts.

  11. Management of Multiple Nitrogen Sources during Wine Fermentation by Saccharomyces cerevisiae.

    Crépin, Lucie; Truong, Nhat My; Bloem, Audrey; Sanchez, Isabelle; Dequin, Sylvie; Camarasa, Carole

    2017-03-01

    During fermentative growth in natural and industrial environments, Saccharomyces cerevisiae must redistribute the available nitrogen from multiple exogenous sources to amino acids in order to suitably fulfill anabolic requirements. To exhaustively explore the management of this complex resource, we developed an advanced strategy based on the reconciliation of data from a set of stable isotope tracer experiments with labeled nitrogen sources. Thus, quantifying the partitioning of the N compounds through the metabolism network during fermentation, we demonstrated that, contrary to the generally accepted view, only a limited fraction of most of the consumed amino acids is directly incorporated into proteins. Moreover, substantial catabolism of these molecules allows for efficient redistribution of nitrogen, supporting the operative de novo synthesis of proteinogenic amino acids. In contrast, catabolism of consumed amino acids plays a minor role in the formation of volatile compounds. Another important feature is that the α-keto acid precursors required for the de novo syntheses originate mainly from the catabolism of sugars, with a limited contribution from the anabolism of consumed amino acids. This work provides a comprehensive view of the intracellular fate of consumed nitrogen sources and the metabolic origin of proteinogenic amino acids, highlighting a strategy of distribution of metabolic fluxes implemented by yeast as a means of adapting to environments with changing and scarce nitrogen resources. IMPORTANCE A current challenge for the wine industry, in view of the extensive competition in the worldwide market, is to meet consumer expectations regarding the sensory profile of the product while ensuring an efficient fermentation process. Understanding the intracellular fate of the nitrogen sources available in grape juice is essential to the achievement of these objectives, since nitrogen utilization affects both the fermentative activity of yeasts and the

  12. Management of Multiple Nitrogen Sources during Wine Fermentation by Saccharomyces cerevisiae

    Crépin, Lucie; Truong, Nhat My; Bloem, Audrey; Sanchez, Isabelle; Dequin, Sylvie

    2017-01-01

    ABSTRACT During fermentative growth in natural and industrial environments, Saccharomyces cerevisiae must redistribute the available nitrogen from multiple exogenous sources to amino acids in order to suitably fulfill anabolic requirements. To exhaustively explore the management of this complex resource, we developed an advanced strategy based on the reconciliation of data from a set of stable isotope tracer experiments with labeled nitrogen sources. Thus, quantifying the partitioning of the N compounds through the metabolism network during fermentation, we demonstrated that, contrary to the generally accepted view, only a limited fraction of most of the consumed amino acids is directly incorporated into proteins. Moreover, substantial catabolism of these molecules allows for efficient redistribution of nitrogen, supporting the operative de novo synthesis of proteinogenic amino acids. In contrast, catabolism of consumed amino acids plays a minor role in the formation of volatile compounds. Another important feature is that the α-keto acid precursors required for the de novo syntheses originate mainly from the catabolism of sugars, with a limited contribution from the anabolism of consumed amino acids. This work provides a comprehensive view of the intracellular fate of consumed nitrogen sources and the metabolic origin of proteinogenic amino acids, highlighting a strategy of distribution of metabolic fluxes implemented by yeast as a means of adapting to environments with changing and scarce nitrogen resources. IMPORTANCE A current challenge for the wine industry, in view of the extensive competition in the worldwide market, is to meet consumer expectations regarding the sensory profile of the product while ensuring an efficient fermentation process. Understanding the intracellular fate of the nitrogen sources available in grape juice is essential to the achievement of these objectives, since nitrogen utilization affects both the fermentative activity of yeasts and

  13. Radiation protection with consumer products containing gaseous tritium light sources

    Rahders, Erio; Haeusler, Uwe

    2017-01-01

    Consumer products containing gaseous tritium light sources (GTLS) were examined with respect to their radiological safety potential regarding leak tightness or accidents. The maximum tritium leakage rate of 2.7 Bq/d determined from experimental testing is well below the criterion for leak tightness of sealed radioactive sources in DIN 25426-4. In order to investigate the incorporation of tritium due to contact with consumer products, 2 scenarios were reviewed; the correct use of a tritium watch and the accident scenario with a keyring.

  14. Observations on multiple pion production by hadrons of cosmic radiation

    Mantovani, M.S.M.

    1971-01-01

    Using two emulsion chambers exposed at Mt. Chacaltaya with jet producer layers of pitch, about 100 nuclear interactions were detected and analyzed. The results are compared with other experiments. Emission of a small fireball with M sub(γ) approximately equal to 1.3 Gev/c 2 is confirmed im multiple production process. Re-analysis of the Bristol-Bombay experiment of a balloon emulsion chamber confirmed the existence of such emission and added informations about emission of a intermediate state of higher mass (M sub(γ) approximately equal to 7.7 Gev/c 2 ). Fireball analysis on the Texas Lone Star of the Bristol Group shows a fireball of still larger mass (M sub(γ) approximately equal to 78 Gev/c 2 )

  15. Institutional and pedagogical criteria for productive open source learning environments

    Svendsen, Brian Møller; Ryberg, Thomas; Semey, Ian Peter

    2004-01-01

    In this article we present some institutional and pedagogical criteria for making an informed decision in relation to identifying and choosing a productive open source learning environment. We argue that three concepts (implementation, maintainability and further development) are important when...... considering the sustainability and cost efficiency of an open source system, and we outline a set of key points for evaluating an open source software in terms of cost of system adoption. Furthermore we identify a range of pedagogical concepts and criteria to emphasize the importance of considering...... the relation between the local pedagogical practice and the pedagogical design of the open source learning environment. This we illustrate through an analysis of an open source system and our own pedagogical practice at Aalborg University, Denmark (POPP)....

  16. Can fungi compete with marine sources for chitosan production?

    Ghormade, V; Pathan, E K; Deshpande, M V

    2017-11-01

    Chitosan, a β-1,4-linked glucosamine polymer is formed by deacetylation of chitin. It has a wide range of applications from agriculture to human health care products. Chitosan is commercially produced from shellfish, shrimp waste, crab and lobster processing using strong alkalis at high temperatures for long time periods. The production of chitin and chitosan from fungal sources has gained increased attention in recent years due to potential advantages in terms of homogenous polymer length, high degree of deacetylation and solubility over the current marine source. Zygomycetous fungi such as Absidia coerulea, Benjaminiella poitrasii, Cunninghamella elegans, Gongrenella butleri, Mucor rouxii, Mucor racemosus and Rhizopus oryzae have been studied extensively. Isolation of chitosan are reported from few edible basidiomycetous fungi like Agaricus bisporus, Lentinula edodes and Pleurotus sajor-caju. Other organisms from mycotech industries explored for chitosan production are Aspergillus niger, Penicillium chrysogenum, Saccharomyces cerevisiae and other wine yeasts. Number of aspects such as value addition to the existing applications of fungi, utilization of waste from agriculture sector, and issues and challenges for the production of fungal chitosan to compete with existing sources, metabolic engineering and novel applications have been discussed to adjudge the potential of fungal sources for commercial chitosan production. Copyright © 2017 Elsevier B.V. All rights reserved.

  17. Profile of the Brazilian scientific production in multiple sclerosis

    Araujo C.R.

    2006-01-01

    Full Text Available This paper analyzes the profile of the Brazilian output in the field of multiple sclerosis from 1981 to 2004. The search was conducted through the MEDLINE and LILACS databases, selecting papers in which the term "multiple sclerosis" was defined as the main topic and "Brazil" or "Brasil" as others. The data were analyzed regarding the themes, the state in Brazil and institution where the papers were produced, the journals where the papers were published, journal's impact factor, and language. The search disclosed 141 documents (91 from MEDLINE and LILACS, and 50 from LILACS only published in 44 different journals (23 of them MEDLINE-indexed. A total of 111 documents were produced by 17 public universities, 29 by 3 private medical schools and 1 by a non-governmental organization. There were 65 original contributions, 37 case reports, 20 reviews, 6 PhD dissertations, 5 guidelines, 2 validation studies, 2 clinical trials, 2 chapters in textbooks, 1 Master of Science thesis, and 1 patient education handout. The journal impact factor ranged from 0.0217 to 6.039 (median 3.03. Of 91 papers from MEDLINE, 65 were published by Arquivos de Neuro-Psiquiatria. More than 90% of the papers were written in Portuguese. São Paulo was the most productive state in the country, followed by Rio de Janeiro, Minas Gerais and Paraná. Eighty-two percent of the Brazilian output came from the Southeastern region.

  18. Ultrasonic waste activated sludge disintegration for recovering multiple nutrients for biofuel production.

    Xie, Guo-Jun; Liu, Bing-Feng; Wang, Qilin; Ding, Jie; Ren, Nan-Qi

    2016-04-15

    Waste activated sludge is a valuable resource containing multiple nutrients, but is currently treated and disposed of as an important source of pollution. In this work, waste activated sludge after ultrasound pretreatment was reused as multiple nutrients for biofuel production. The nutrients trapped in sludge floc were transferred into liquid medium by ultrasonic disintegration during first 30 min, while further increase of pretreatment time only resulted in slight increase of nutrients release. Hydrogen production by Ethanoligenens harbinense B49 from glucose significantly increased with the concentration of ultrasonic sludge, and reached maximum yield of 1.97 mol H2/mol glucose at sludge concentration of 7.75 g volatile suspended solids/l. Without addition of any other chemicals, waste molasses rich in carbohydrate was efficiently turned into hydrogen with yield of 189.34 ml H2/g total sugar by E. harbinense B49 using ultrasonic sludge as nutrients. The results also showed that hydrogen production using pretreated sludge as multiple nutrients was higher than those using standard nutrients. Acetic acid produced by E. harbinense B49 together with the residual nutrients in the liquid medium were further converted into hydrogen (271.36 ml H2/g total sugar) by Rhodopseudomonas faecalis RLD-53 through photo fermentation, while ethanol was the sole end product with yield of 220.26 mg/g total sugar. Thus, pretreated sludge was an efficient nutrients source for biofuel production, which could replace the standard nutrients. This research provided a novel strategy to achieve environmental friendly sludge disposal and simultaneous efficient biofuel recovery from organic waste. Copyright © 2016 Elsevier Ltd. All rights reserved.

  19. Ion source developments for RNB production at Spiral / GANIL

    Villari, A.C.C.; Barue, C.; Gaubert, G.; Gibouin, S.; Huguet, Y.; Jardin, P.; Kandri-Rody, S.; Landre-Pellemoine, F.; Lecesne, N.; Leroy, R.; Lewitowicz, M.; Marry, C.; Maunoury, L.; Pacquet, J.Y.; Rataud, J.P.; Saint-Laurent, M.G.; Stodel, C.; Lichtenthaeler, R.; Angelique, J.C.; Orr, N.A.

    2000-01-01

    The first on-line production system for SPIRAL/GANIL (Radioactive Ion Production System with Acceleration on-Line) phase-I has been commissioned on the SIRa (Radioactive Ion Separator) test bench. Exotic multicharged noble gas ion beams have been obtained during several days. In parallel, a new ECRIS (Electron Cyclotron Resonance Ion Source) for mono-charged ions has also been developed. Preliminary, off-line results are presented. (authors)

  20. Use of ultrasonic array method for positioning multiple partial discharge sources in transformer oil.

    Xie, Qing; Tao, Junhan; Wang, Yongqiang; Geng, Jianghai; Cheng, Shuyi; Lü, Fangcheng

    2014-08-01

    Fast and accurate positioning of partial discharge (PD) sources in transformer oil is very important for the safe, stable operation of power systems because it allows timely elimination of insulation faults. There is usually more than one PD source once an insulation fault occurs in the transformer oil. This study, which has both theoretical and practical significance, proposes a method of identifying multiple PD sources in the transformer oil. The method combines the two-sided correlation transformation algorithm in the broadband signal focusing and the modified Gerschgorin disk estimator. The method of classification of multiple signals is used to determine the directions of arrival of signals from multiple PD sources. The ultrasonic array positioning method is based on the multi-platform direction finding and the global optimization searching. Both the 4 × 4 square planar ultrasonic sensor array and the ultrasonic array detection platform are built to test the method of identifying and positioning multiple PD sources. The obtained results verify the validity and the engineering practicability of this method.

  1. Potential feedstock sources for ethanol production in Florida

    Rahmani, Mohammad [Univ. of Florida, Gainesville, FL (United States); Hodges, Alan [Univ. of Florida, Gainesville, FL (United States)

    2015-10-01

    This study presents information on the potential feedstock sources that may be used for ethanol production in Florida. Several potential feedstocks for fuel ethanol production in Florida are discussed, such as, sugarcane, corn, citrus byproducts and sweet sorghum. Other probable impacts need to be analyzed for sugarcane to ethanol production as alternative uses of sugarcane may affect the quantity of sugar production in Florida. While citrus molasses is converted to ethanol as an established process, the cost of ethanol is higher, and the total amount of citrus molasses per year is insignificant. Sorghum cultivars have the potential for ethanol production. However, the agricultural practices for growing sweet sorghum for ethanol have not been established, and the conversion process must be tested and developed at a more expanded level. So far, only corn shipped from other states to Florida has been considered for ethanol production on a commercial scale. The economic feasibility of each of these crops requires further data and technical analysis.

  2. Hydrogen Production Costs of Various Primary Energy Sources

    Choi, Jae Hyuk; Tak, Nam Il; Kim, Yong Hee; Park, Won Seok

    2005-11-01

    Many studies on the economical aspects of hydrogen energy technologies have been conducted with the increase of the technical and socioeconomic importance of the hydrogen energy. However, there is still no research which evaluates the economy of hydrogen production from the primary energy sources in consideration of Korean situations. In this study, the hydrogen production costs of major primary energy sources are compared in consideration of the Korean situations such as feedstock price, electricity rate, and load factor. The evaluation methodology is based on the report of the National Academy of Science (NAS) of U.S. The present study focuses on the possible future technology scenario defined by NAS. The scenario assumes technological improvement that may be achieved if present research and development (R and D) programs are successful. The production costs by the coal and natural gas are 1.1 $/kgH 2 and 1.36 $/kgH 2 , respectively. However, the fossil fuels are susceptible to the price variation depending on the oil and the raw material prices, and the hydrogen production cost also depends on the carbon tax. The economic competitiveness of the renewable energy sources such as the wind, solar, and biomass are relatively low when compared with that of the other energy sources. The estimated hydrogen production costs from the renewable energy sources range from 2.35 $/kgH 2 to 6.03 $/kgH 2 . On the other hand, the production cost by nuclear energy is lower than that of natural gas or coal when the prices of the oil and soft coal are above $50/barrel and 138 $/ton, respectively. Taking into consideration the recent rapid increase of the oil and soft coal prices and the limited fossil resource, the nuclear-hydrogen option appears to be the most economical way in the future

  3. Study on a volume-production H- ion source

    Takama, S.

    1988-01-01

    H - ions formed by volume-production are extracted from a multicuspion source. By applying a large positive bias to the plasma electrode, the ratio I - /I e becomes 1/20. H - ion current of 0.4mA is extracted from a 0.3cm 2 circular aperture at an arc current of 10A. (author)

  4. Particle production in field theories coupled to strong external sources, I: Formalism and main results

    Gelis, Francois; Venugopalan, Raju

    2006-01-01

    We develop a formalism for particle production in a field theory coupled to a strong time-dependent external source. An example of such a theory is the color glass condensate. We derive a formula, in terms of cut vacuum-vacuum Feynman graphs, for the probability of producing a given number of particles. This formula is valid to all orders in the coupling constant. The distribution of multiplicities is non-Poissonian, even in the classical approximation. We investigate an alternative method of calculating the mean multiplicity. At leading order, the average multiplicity can be expressed in terms of retarded solutions of classical equations of motion. We demonstrate that the average multiplicity at next-to-leading order can be formulated as an initial value problem by solving equations of motion for small fluctuation fields with retarded boundary conditions. The variance of the distribution can be calculated in a similar fashion. Our formalism therefore provides a framework to compute from first principles particle production in proton-nucleus and nucleus-nucleus collisions beyond leading order in the coupling constant and to all orders in the source density. We also provide a transparent interpretation (in conventional field theory language) of the well-known Abramovsky-Gribov-Kancheli (AGK) cancellations. Explicit connections are made between the framework for multi-particle production developed here and the framework of reggeon field theory

  5. Multiple sclerosis: patients’ information sources and needs on disease symptoms and management

    Albert I Matti

    2010-06-01

    Full Text Available Albert I Matti1, Helen McCarl2, Pamela Klaer2, Miriam C Keane1, Celia S Chen11Department of Ophthalmology, Flinders Medical Centre and Flinders University, Bedford Park, SA, Australia; 2The Multiple Sclerosis Society of South Australia and Northern Territory, Klemzig, SA, AustraliaObjective: To investigate the current information sources of patients with multiple sclerosis (MS in the early stages of their disease and to identify patients’ preferred source of information. The relative amounts of information from the different sources were also compared.Methods: Participants at a newly diagnosed information session organized by the Multiple Sclerosis Society of South Australia were invited to complete a questionnaire. Participants were asked to rate on a visual analog scale how much information they had received about MS and optic neuritis from different information sources and how much information they would like to receive from each of the sources.Results: A close to ideal amount of information is being provided by the MS society and MS specialist nurses. There is a clear deficit between what information patients are currently receiving and the amount of information they actually want from various sources. Patients wish to receive significantly more information from treating general practitioners, eye specialists, neurologists, and education sessions. Patients have identified less than adequate information received on optic neuritis from all sources.Conclusion: This study noted a clear information deficit regarding MS from all sources. This information deficit is more pronounced in relation to optic neuritis and needs to be addressed in the future.Practice implications: More patient information and counselling needs to be provided to MS patients even at early stages of their disease, especially in relation to management of disease relapse.Keywords: information sources, information needs, MS patients, optic neuritis

  6. Multiple particle production processes in the ''light'' of quantum optics

    Friedlander, E.M.

    1990-09-01

    Ever since the observation that high-energy ''nuclear active'' cosmic-ray particles create bunches of penetrating particles upon hitting targets, a controversy has raged about whether these secondaries are created in a ''single act'' or whether many hadrons are just the result of an intra-nuclear cascade, yielding one meson in every step. I cannot escape the impression that: the latter kind of model appeals naturally as a consequence of an innate bio-morphism in our way of thinking and that in one guise or another it has tenaciously survived to this day, also for hadron-hadron collisions, via multi-peripheral models to the modern parton shower approach. Indeed, from the very beginning of theoretical consideration of multiparticle production, the possibility of many particles arising from a single ''hot'' system has been explored, with many fruitful results, not the least of which are the s 1/4 dependence of the mean produced particle multiplicity and the ''thermal'' shape of the P T spectra. An important consequence of the thermodynamical-hydrodynamical models is that particle emission is treated in analogy to black-body radiation, implying for the secondaries a set of specific Quantum-Statistical properties, very similar to those observed in quantum optics. From here on I shall try to review a number of implications and applications of this QS analogy in the study of multiplicity distributions of the produced secondaries. I will touch only in passing another very important topic of this class, the Bose-Einstein two-particle correlations

  7. Mobility and Sector-specific Effects of Changes in Multiple Sources ...

    Using the second and third Cameroon household consumption surveys, this study examined mobility and sector-specific effects of changes in multiple sources of deprivation in Cameroon. Results indicated that between 2001 and 2007, deprivations associated with human capital and labour capital reduced, while ...

  8. Transfer functions of double- and multiple-cavity Fabry-Perot filters driven by Lorentzian sources.

    Marti, J; Capmany, J

    1996-12-20

    We derive expressions for the transfer functions of double- and multiple-cavity Fabry-Perot filters driven by laser sources with Lorentzian spectrum. These are of interest because of their applications in sensing and channel filtering in optical frequency-division multiplexing networks.

  9. Organizational Communication in Emergencies: Using Multiple Channels and Sources to Combat Noise and Capture Attention

    Stephens, Keri K.; Barrett, Ashley K.; Mahometa, Michael J.

    2013-01-01

    This study relies on information theory, social presence, and source credibility to uncover what best helps people grasp the urgency of an emergency. We surveyed a random sample of 1,318 organizational members who received multiple notifications about a large-scale emergency. We found that people who received 3 redundant messages coming through at…

  10. Reading on the World Wide Web: Dealing with conflicting information from multiple sources

    Van Strien, Johan; Brand-Gruwel, Saskia; Boshuizen, Els

    2011-01-01

    Van Strien, J. L. H., Brand-Gruwel, S., & Boshuizen, H. P. A. (2011, August). Reading on the World Wide Web: Dealing with conflicting information from multiple sources. Poster session presented at the biannual conference of the European Association for Research on Learning and Instruction, Exeter,

  11. How organic carbon derived from multiple sources contributes to carbon sequestration processes in a shallow coastal system?

    Watanabe, Kenta; Kuwae, Tomohiro

    2015-04-16

    Carbon captured by marine organisms helps sequester atmospheric CO 2 , especially in shallow coastal ecosystems, where rates of primary production and burial of organic carbon (OC) from multiple sources are high. However, linkages between the dynamics of OC derived from multiple sources and carbon sequestration are poorly understood. We investigated the origin (terrestrial, phytobenthos derived, and phytoplankton derived) of particulate OC (POC) and dissolved OC (DOC) in the water column and sedimentary OC using elemental, isotopic, and optical signatures in Furen Lagoon, Japan. Based on these data analysis, we explored how OC from multiple sources contributes to sequestration via storage in sediments, water column sequestration, and air-sea CO 2 exchanges, and analyzed how the contributions vary with salinity in a shallow seagrass meadow as well. The relative contribution of terrestrial POC in the water column decreased with increasing salinity, whereas autochthonous POC increased in the salinity range 10-30. Phytoplankton-derived POC dominated the water column POC (65-95%) within this salinity range; however, it was minor in the sediments (3-29%). In contrast, terrestrial and phytobenthos-derived POC were relatively minor contributors in the water column but were major contributors in the sediments (49-78% and 19-36%, respectively), indicating that terrestrial and phytobenthos-derived POC were selectively stored in the sediments. Autochthonous DOC, part of which can contribute to long-term carbon sequestration in the water column, accounted for >25% of the total water column DOC pool in the salinity range 15-30. Autochthonous OC production decreased the concentration of dissolved inorganic carbon in the water column and thereby contributed to atmospheric CO 2 uptake, except in the low-salinity zone. Our results indicate that shallow coastal ecosystems function not only as transition zones between land and ocean but also as carbon sequestration filters. They

  12. Direct Position Determination of Multiple Non-Circular Sources with a Moving Coprime Array

    Yankui Zhang

    2018-05-01

    Full Text Available Direct position determination (DPD is currently a hot topic in wireless localization research as it is more accurate than traditional two-step positioning. However, current DPD algorithms are all based on uniform arrays, which have an insufficient degree of freedom and limited estimation accuracy. To improve the DPD accuracy, this paper introduces a coprime array to the position model of multiple non-circular sources with a moving array. To maximize the advantages of this coprime array, we reconstruct the covariance matrix by vectorization, apply a spatial smoothing technique, and converge the subspace data from each measuring position to establish the cost function. Finally, we obtain the position coordinates of the multiple non-circular sources. The complexity of the proposed method is computed and compared with that of other methods, and the Cramer–Rao lower bound of DPD for multiple sources with a moving coprime array, is derived. Theoretical analysis and simulation results show that the proposed algorithm is not only applicable to circular sources, but can also improve the positioning accuracy of non-circular sources. Compared with existing two-step positioning algorithms and DPD algorithms based on uniform linear arrays, the proposed technique offers a significant improvement in positioning accuracy with a slight increase in complexity.

  13. Direct Position Determination of Multiple Non-Circular Sources with a Moving Coprime Array.

    Zhang, Yankui; Ba, Bin; Wang, Daming; Geng, Wei; Xu, Haiyun

    2018-05-08

    Direct position determination (DPD) is currently a hot topic in wireless localization research as it is more accurate than traditional two-step positioning. However, current DPD algorithms are all based on uniform arrays, which have an insufficient degree of freedom and limited estimation accuracy. To improve the DPD accuracy, this paper introduces a coprime array to the position model of multiple non-circular sources with a moving array. To maximize the advantages of this coprime array, we reconstruct the covariance matrix by vectorization, apply a spatial smoothing technique, and converge the subspace data from each measuring position to establish the cost function. Finally, we obtain the position coordinates of the multiple non-circular sources. The complexity of the proposed method is computed and compared with that of other methods, and the Cramer⁻Rao lower bound of DPD for multiple sources with a moving coprime array, is derived. Theoretical analysis and simulation results show that the proposed algorithm is not only applicable to circular sources, but can also improve the positioning accuracy of non-circular sources. Compared with existing two-step positioning algorithms and DPD algorithms based on uniform linear arrays, the proposed technique offers a significant improvement in positioning accuracy with a slight increase in complexity.

  14. Multiple production of hadrons in deep inelastic processes

    Kiselev, A.V.; Petrov, V.A.

    1985-01-01

    Formulas are proposed for the description of the mean multiplicity of hadrons in deep inelastic processes. On the basis of the existing data, predictions are made for the behavior of the mean multiplicity at higher energies

  15. Simulation of neutron multiplicity measurements using Geant4. Open source software for nuclear arms control

    Kuett, Moritz

    2016-07-07

    Nuclear arms control, including nuclear safeguards and verification technologies for nuclear disarmament typically use software as part of many different technological applications. This thesis proposes to use three open source criteria for such software, allowing users and developers to have free access to a program, have access to the full source code and be able to publish modifications for the program. This proposition is presented and analyzed in detail, together with the description of the development of ''Open Neutron Multiplicity Simulation'', an open source software tool to simulate neutron multiplicity measurements. The description includes physical background of the method, details of the developed program and a comprehensive set of validation calculations.

  16. Q&A. Does lack of product management impact the users of open source?

    Paul Young

    2008-01-01

    Most commercial software companies employ product managers to handle the planning and marketing of software products, whereas few open source projects have a product manager. Does lack of product management impact the users of open source?

  17. Q&A. Does lack of product management impact the users of open source?

    Paul Young

    2008-05-01

    Full Text Available Most commercial software companies employ product managers to handle the planning and marketing of software products, whereas few open source projects have a product manager. Does lack of product management impact the users of open source?

  18. Multiple Speech Source Separation Using Inter-Channel Correlation and Relaxed Sparsity

    Maoshen Jia

    2018-01-01

    Full Text Available In this work, a multiple speech source separation method using inter-channel correlation and relaxed sparsity is proposed. A B-format microphone with four spatially located channels is adopted due to the size of the microphone array to preserve the spatial parameter integrity of the original signal. Specifically, we firstly measure the proportion of overlapped components among multiple sources and find that there exist many overlapped time-frequency (TF components with increasing source number. Then, considering the relaxed sparsity of speech sources, we propose a dynamic threshold-based separation approach of sparse components where the threshold is determined by the inter-channel correlation among the recording signals. After conducting a statistical analysis of the number of active sources at each TF instant, a form of relaxed sparsity called the half-K assumption is proposed so that the active source number in a certain TF bin does not exceed half the total number of simultaneously occurring sources. By applying the half-K assumption, the non-sparse components are recovered by regarding the extracted sparse components as a guide, combined with vector decomposition and matrix factorization. Eventually, the final TF coefficients of each source are recovered by the synthesis of sparse and non-sparse components. The proposed method has been evaluated using up to six simultaneous speech sources under both anechoic and reverberant conditions. Both objective and subjective evaluations validated that the perceptual quality of the separated speech by the proposed approach outperforms existing blind source separation (BSS approaches. Besides, it is robust to different speeches whilst confirming all the separated speeches with similar perceptual quality.

  19. Mercury in products - a source of transboundary pollutant transport

    Munthe, J; Kindbom, K [Swedish Environmental Research Inst., Stockholm (Sweden)

    1997-12-01

    The purpose of this report is to summarize current knowledge on product-related emissions of mercury to air on a European scale, and to estimate the contribution from mercury contained in products, to the total anthropogenic emissions of mercury to air and transboundary transport of mercury in Europe. Products included in this study are batteries, measuring and control instruments, light sources and electrical equipment, all intentionally containing mercury. The main result of this study is that product-related emission of mercury can contribute significantly to total emissions and transboundary transport of mercury in the European region and that measures to limit the use of mercury in products can contribute to an overall decrease of the environmental input of mercury in Europe. It is concluded that: -Mercury contained in products may be emitted to air during consumption, after disposal when incinerated or when volatilized from landfill. Mercury may also be emitted to air during recycling of scrap metal or when accumulated (stored) in society. -The amount of mercury consumed in batteries and in measuring and control instruments had decreased since the late 1980`s. The total use of mercury in light sources and electrical equipment has not changed significantly during the same time period. The contribution to total anthropogenic emissions of mercury to air in Europe in the mid 1990`s is estimated to be: for batteries 4%; for measuring and control instruments 3%; for lighting and electrical equipment 11%. -Mercury in products leads to significant wet deposition input in Scandinavia. The relative amount of the total deposition flux attributable to products is estimated to be 10-14% 26 refs, 4 figs, 10 tabs

  20. Multiplicity distributions in a thermodynamical model of hadron production in e{sup +}e{sup -} collisions

    Becattini, F. [Florence Univ. (Italy)]|[Istituto Nazionale di Fisica Nucleare, Florence (Italy); Giovannini, A. [Turin Univ. (Italy). Ist. di Fisica Teorica]|[Istituto Nazionale di Fisica Nucleare, Turin (Italy); Lupia, S. [Max-Planck-Institut fuer Physik, Muenchen (Germany). Werner-Heisenberg-Institut

    1996-10-01

    Predictions of a thermodynamical model of hadron production for multiplicity distributions in e{sup +}e{sup -} annihilations at LEP and PEP-PETRA centre of mass energies are shown. The production process is described as a two-step process in which primary hadrons emitted from the thermal source decay into final observable particles. The final charged track multiplicity distributions turn out to be of negative binomial type and are in quite good agreement with experimental observations. The average number of clans calculated from fitted negative binomial coincides with the average number of primary hadrons predicted by the thermodynamical model, suggesting that clans should be identified with primary hadrons. (orig.)

  1. Production of radioisotopic gamma radiation sources in JAERI

    Katoh, Hisashi; Kogure, Hiroto; Suzuki, Kyohei

    1980-04-01

    The present state of production of gamma radiation sources in Japan Atomic Energy Research Institute (JAERI) is described. Sources of 192 Ir, 60 Co and 170 Tm for industrial and 198 Au and 192 Ir for medical applications are produced and delivered routinely by JAERI. Prefabricated assembly targets are irradiated in JRR-2, JRR-3, JRR-4 or JMTR. The irradiated targets are disassembled in a heavy density concrete cave or a lead-shielded cell, depending on the level of radioactivity. The yield of radioactivity in each target is measured with the aid of an ionization chamber. Where necessary, irradiated targets are encapsulated hermetically in capsules of aluminium, stainless steel or other material. The yield of radioactivity is estimated in relation with the burn-up of target nuclide and product nuclide. (author)

  2. Production, Distribution, and Applications of Californium-252 Neutron Sources

    Balo, P.A.; Knauer, J.B.; Martin, R.C.

    1999-01-01

    The radioisotope 252 Cf is routinely encapsulated into compact, portable, intense neutron sources with a 2.6-year half-life. A source the size of a person's little finger can emit up to 10 11 neutrons/s. Californium-252 is used commercially as a reliable, cost-effective neutron source for prompt gamma neutron activation analysis (PGNAA) of coal, cement, and minerals, as well as for detection and identification of explosives, laud mines, and unexploded military ordnance. Other uses are neutron radiography, nuclear waste assays, reactor start-up sources, calibration standards, and cancer therapy. The inherent safety of source encapsulations is demonstrated by 30 years of experience and by U.S. Bureau of Mines tests of source survivability during explosions. The production and distribution center for the U. S Department of Energy (DOE) Californium Program is the Radiochemical Engineering Development Center (REDC) at Oak Ridge National Laboratory (ORNL). DOE sells 252 Cf to commercial reencapsulators domestically and internationally. Sealed 252 Cf sources are also available for loan to agencies and subcontractors of the U.S. government and to universities for educational, research, and medical applications. The REDC has established the Californium User Facility (CUF) for Neutron Science to make its large inventory of 252 Cf sources available to researchers for irradiations inside uncontaminated hot cells. Experiments at the CUF include a land mine detection system, neutron damage testing of solid-state detectors, irradiation of human cancer cells for boron neutron capture therapy experiments, and irradiation of rice to induce genetic mutations

  3. Fission product source terms and engineered safety features

    Malinauskas, A.P.

    1984-01-01

    The author states that new, technically defensible, methodologies to establish realistic source term values for nuclear reactor accidents will soon be available. Although these methodologies will undoubtedly find widespread use in the development of accident response procedures, the author states that it is less clear that the industry is preparing to employ the newer results to develop a more rational approach to strategies for the mitigation of fission product releases. Questions concerning the performance of existing engineered safety systems are reviewed

  4. Neutron production enhancements for the Intense Pulsed Neutron Source.

    Iverson, E. B.

    1999-01-04

    The Intense Pulsed Neutron Source (IPNS) was the first high energy spallation neutron source in the US dedicated to materials research. It has operated for sixteen years, and in that time has had a very prolific record concerning the development of new target and moderator systems for pulsed spallation sources. IPNS supports a very productive user program on its thirteen instruments, which are oversubscribed by more than two times, meanwhile having an excellent overall reliability of 95%. Although the proton beam power is relatively low at 7 kW, the target and moderator systems are very efficient. The typical beam power which gives an equivalent flux for long-wavelength neutrons is about 60 kW, due to the use of a uranium target and liquid and solid methane moderators, precluded at some sources due to a higher accelerator power. The development of new target and moderator systems is by no means stagnant at IPNS. They are presently considering numerous enhancements to the target and moderators that offer prospects for increasing the useful neutron production by substantial factors. Many of these enhancements could be combined, although their combined benefit has not yet been well established. Meanwhile, IPNS is embarking on a coherent program of study concerning these improvements and their possible combination and implementation. Moreover, any improvements accomplished at IPNS would immediately increase the performance of IPNS instruments.

  5. Neutron production enhancements for the Intense Pulsed Neutron Source

    Iverson, E. B.

    1999-01-01

    The Intense Pulsed Neutron Source (IPNS) was the first high energy spallation neutron source in the US dedicated to materials research. It has operated for sixteen years, and in that time has had a very prolific record concerning the development of new target and moderator systems for pulsed spallation sources. IPNS supports a very productive user program on its thirteen instruments, which are oversubscribed by more than two times, meanwhile having an excellent overall reliability of 95%. Although the proton beam power is relatively low at 7 kW, the target and moderator systems are very efficient. The typical beam power which gives an equivalent flux for long-wavelength neutrons is about 60 kW, due to the use of a uranium target and liquid and solid methane moderators, precluded at some sources due to a higher accelerator power. The development of new target and moderator systems is by no means stagnant at IPNS. They are presently considering numerous enhancements to the target and moderators that offer prospects for increasing the useful neutron production by substantial factors. Many of these enhancements could be combined, although their combined benefit has not yet been well established. Meanwhile, IPNS is embarking on a coherent program of study concerning these improvements and their possible combination and implementation. Moreover, any improvements accomplished at IPNS would immediately increase the performance of IPNS instruments

  6. Improving wheat productivity through source and timing of nitrogen fertilization

    Jan, M.T.; Khan, A.; Afridi, M.Z.; Arif, M.; Khan, M.J.; Farhatullah; Jan, D.; Saeed, M.

    2011-01-01

    Efficient nitrogen (N) fertilizer management is critical for the improved production of wheat (Triticum aestivum L.) and can be achieved through source and timing of N application. Thus, an experiment was carried out at the Research Farm of KPK Agricultural University Peshawar during 2005-06 to test the effects of sources and timing of N application on yield and yield components of wheat. Nitrogen sources were ammonium (NH/sub 4/) and nitrate (NO/sub 3/) applied at the rate of 100 kg ha/sup -1/ at three different stages i.e., at sowing (S1), tillering (S2) and boot stage (S3). Ammonium N increased yield component but did not affect the final grain yield. Split N application at sowing, tillering and boot stages had increased productive tillers m-2, and thousand grains weight, whereas grain yield was higher when N was applied at tillering and boot stages. Nitrogen fertilization increased 20% grain yield compared to control regardless of N application time. It was concluded from the experiment that split application of NH/sub 4/-N performed better than full dose application and/or NO/sub 3/-N for improved wheat productivity and thus, is recommended for general practice in agro-climatic conditions of Peshawar. (author)

  7. Response of secondary production and its components to multiple stressors in nematode field populations.

    Doroszuk, A.; Brake, te E.; Crespo-Gonzalez, D.; Kammenga, J.E.

    2007-01-01

    Realistic measures of the impact of individual or multiple stressors are important for ecological risk assessment. Although multiple anthropogenic stressors are common in human-dominated environments, knowledge of their influence on functional population parameters such as secondary production (P)

  8. Indirect detection of radiation sources through direct detection of radiolysis products

    Farmer, Joseph C [Tracy, CA; Fischer, Larry E [Los Gatos, CA; Felter, Thomas E [Livermore, CA

    2010-04-20

    A system for indirectly detecting a radiation source by directly detecting radiolytic products. The radiation source emits radiation and the radiation produces the radiolytic products. A fluid is positioned to receive the radiation from the radiation source. When the fluid is irradiated, radiolytic products are produced. By directly detecting the radiolytic products, the radiation source is detected.

  9. Modeling of nitrous oxide production by autotrophic ammonia-oxidizing bacteria with multiple production pathways.

    Ni, Bing-Jie; Peng, Lai; Law, Yingyu; Guo, Jianhua; Yuan, Zhiguo

    2014-04-01

    Autotrophic ammonia oxidizing bacteria (AOB) have been recognized as a major contributor to N2O production in wastewater treatment systems. However, so far N2O models have been proposed based on a single N2O production pathway by AOB, and there is still a lack of effective approach for the integration of these models. In this work, an integrated mathematical model that considers multiple production pathways is developed to describe N2O production by AOB. The pathways considered include the nitrifier denitrification pathway (N2O as the final product of AOB denitrification with NO2(-) as the terminal electron acceptor) and the hydroxylamine (NH2OH) pathway (N2O as a byproduct of incomplete oxidation of NH2OH to NO2(-)). In this model, the oxidation and reduction processes are modeled separately, with intracellular electron carriers introduced to link the two types of processes. The model is calibrated and validated using experimental data obtained with two independent nitrifying cultures. The model satisfactorily describes the N2O data from both systems. The model also predicts shifts of the dominating pathway at various dissolved oxygen (DO) and nitrite levels, consistent with previous hypotheses. This unified model is expected to enhance our ability to predict N2O production by AOB in wastewater treatment systems under varying operational conditions.

  10. Source location in plates based on the multiple sensors array method and wavelet analysis

    Yang, Hong Jun; Shin, Tae Jin; Lee, Sang Kwon

    2014-01-01

    A new method for impact source localization in a plate is proposed based on the multiple signal classification (MUSIC) and wavelet analysis. For source localization, the direction of arrival of the wave caused by an impact on a plate and the distance between impact position and sensor should be estimated. The direction of arrival can be estimated accurately using MUSIC method. The distance can be obtained by using the time delay of arrival and the group velocity of the Lamb wave in a plate. Time delay is experimentally estimated using the continuous wavelet transform for the wave. The elasto dynamic theory is used for the group velocity estimation.

  11. Source location in plates based on the multiple sensors array method and wavelet analysis

    Yang, Hong Jun; Shin, Tae Jin; Lee, Sang Kwon [Inha University, Incheon (Korea, Republic of)

    2014-01-15

    A new method for impact source localization in a plate is proposed based on the multiple signal classification (MUSIC) and wavelet analysis. For source localization, the direction of arrival of the wave caused by an impact on a plate and the distance between impact position and sensor should be estimated. The direction of arrival can be estimated accurately using MUSIC method. The distance can be obtained by using the time delay of arrival and the group velocity of the Lamb wave in a plate. Time delay is experimentally estimated using the continuous wavelet transform for the wave. The elasto dynamic theory is used for the group velocity estimation.

  12. Hydrogen production from coal using a nuclear heat source

    Quade, R.N.

    1977-01-01

    A strong candidate for hydrogen production in the intermediate time frame of 1990 to 1995 is a coal-based process using a high-temperature gas-cooled reactor (HTGR) as a heat source. Expected process efficiencies in the range of 60 to 70% are considerably higher than all other hydrogen production processes except steam reforming of a natural gas - a feedstock which may not be available in large quantities in this time frame. The process involves the preparation of a coal liquid, hydrogasification of that liquid, and steam reforming of the resulting gaseous or light liquid product. Bench-scale experimental work on the hydrogasification of coal liquids is being carried out. A study showing process efficiency and cost of hydrogen vs nuclear reactor core outlet temperature has been completed and shows diminishing returns at process temperatures above about 1500 0 F. (author)

  13. Hydrogen production from coal using a nuclear heat source

    Quade, R. N.

    1976-01-01

    A strong candidate for hydrogen production in the intermediate time frame of 1985 to 1995 is a coal-based process using a high-temperature gas-cooled reactor (HTGR) as a heat source. Expected process efficiencies in the range of 60 to 70% are considerably higher than all other hydrogen production processes except steam reforming of a natural gas. The process involves the preparation of a coal liquid, hydrogasification of that liquid, and steam reforming of the resulting gaseous or light liquid product. A study showing process efficiency and cost of hydrogen vs nuclear reactor core outlet temperature has been completed, and shows diminishing returns at process temperatures above about 1500 F. A possible scenario combining the relatively abundant and low-cost Western coal deposits with the Gulf Coast hydrogen users is presented which provides high-energy density transportation utilizing coal liquids and uranium.

  14. Monte Carlo analyses of the source multiplication factor of the YALINA booster facility

    Talamo, Alberto; Gohar, Y.; Kondev, F.; Aliberti, Gerardo [Argonne National Laboratory, 9700 South Cass Avenue, Argonne, IL 60439 (United States); Bolshinsky, I. [Idaho National Laboratory, P. O. Box 2528, Idaho Falls, Idaho 83403 (United States); Kiyavitskaya, Hanna; Bournos, Victor; Fokov, Yury; Routkovskaya, Christina; Serafimovich, Ivan [Joint Institute for Power and Nuclear Research-Sosny, National Academy of Sciences, Minsk, acad. Krasin, 99, 220109 (Belarus)

    2008-07-01

    The multiplication factor of a subcritical assembly is affected by the energy spectrum and spatial distribution of the neutron source. In a critical assembly, neutrons emerge from the fission reactions with an average energy of approx2 MeV; in a deuteron accelerator driven subcritical assembly, neutrons emerge from the fusion target with a fixed energy of 2.45 or 14.1 MeV, from the Deuterium-Deuterium (D-D) and Deuterium-Tritium (D-T) reactions respectively. This study aims at generating accurate neutronics models for the YALINA Booster facility, based on the use of different Monte Carlo neutron transport codes, at defining the facility key physical parameters, and at comparing the neutron multiplication factor for three different neutron sources: fission, D-D and D-T. The calculated values are compared with the experimental results. (authors)

  15. Monte Carlo analyses of the source multiplication factor of the YALINA booster facility

    Talamo, Alberto; Gohar, Y.; Kondev, F.; Aliberti, Gerardo; Bolshinsky, I.; Kiyavitskaya, Hanna; Bournos, Victor; Fokov, Yury; Routkovskaya, Christina; Serafimovich, Ivan

    2008-01-01

    The multiplication factor of a subcritical assembly is affected by the energy spectrum and spatial distribution of the neutron source. In a critical assembly, neutrons emerge from the fission reactions with an average energy of ∼2 MeV; in a deuteron accelerator driven subcritical assembly, neutrons emerge from the fusion target with a fixed energy of 2.45 or 14.1 MeV, from the Deuterium-Deuterium (D-D) and Deuterium-Tritium (D-T) reactions respectively. This study aims at generating accurate neutronics models for the YALINA Booster facility, based on the use of different Monte Carlo neutron transport codes, at defining the facility key physical parameters, and at comparing the neutron multiplication factor for three different neutron sources: fission, D-D and D-T. The calculated values are compared with the experimental results. (authors)

  16. Distributed 3D Source Localization from 2D DOA Measurements Using Multiple Linear Arrays

    Antonio Canclini

    2017-01-01

    Full Text Available This manuscript addresses the problem of 3D source localization from direction of arrivals (DOAs in wireless acoustic sensor networks. In this context, multiple sensors measure the DOA of the source, and a central node combines the measurements to yield the source location estimate. Traditional approaches require 3D DOA measurements; that is, each sensor estimates the azimuth and elevation of the source by means of a microphone array, typically in a planar or spherical configuration. The proposed methodology aims at reducing the hardware and computational costs by combining measurements related to 2D DOAs estimated from linear arrays arbitrarily displaced in the 3D space. Each sensor measures the DOA in the plane containing the array and the source. Measurements are then translated into an equivalent planar geometry, in which a set of coplanar equivalent arrays observe the source preserving the original DOAs. This formulation is exploited to define a cost function, whose minimization leads to the source location estimation. An extensive simulation campaign validates the proposed approach and compares its accuracy with state-of-the-art methodologies.

  17. A Monte Carlo multiple source model applied to radiosurgery narrow photon beams

    Chaves, A.; Lopes, M.C.; Alves, C.C.; Oliveira, C.; Peralta, L.; Rodrigues, P.; Trindade, A.

    2004-01-01

    Monte Carlo (MC) methods are nowadays often used in the field of radiotherapy. Through successive steps, radiation fields are simulated, producing source Phase Space Data (PSD) that enable a dose calculation with good accuracy. Narrow photon beams used in radiosurgery can also be simulated by MC codes. However, the poor efficiency in simulating these narrow photon beams produces PSD whose quality prevents calculating dose with the required accuracy. To overcome this difficulty, a multiple source model was developed that enhances the quality of the reconstructed PSD, reducing also the time and storage capacities. This multiple source model was based on the full MC simulation, performed with the MC code MCNP4C, of the Siemens Mevatron KD2 (6 MV mode) linear accelerator head and additional collimators. The full simulation allowed the characterization of the particles coming from the accelerator head and from the additional collimators that shape the narrow photon beams used in radiosurgery treatments. Eight relevant photon virtual sources were identified from the full characterization analysis. Spatial and energy distributions were stored in histograms for the virtual sources representing the accelerator head components and the additional collimators. The photon directions were calculated for virtual sources representing the accelerator head components whereas, for the virtual sources representing the additional collimators, they were recorded into histograms. All these histograms were included in the MC code, DPM code and using a sampling procedure that reconstructed the PSDs, dose distributions were calculated in a water phantom divided in 20000 voxels of 1x1x5 mm 3 . The model accurately calculates dose distributions in the water phantom for all the additional collimators; for depth dose curves, associated errors at 2σ were lower than 2.5% until a depth of 202.5 mm for all the additional collimators and for profiles at various depths, deviations between measured

  18. MRMer, an interactive open source and cross-platform system for data extraction and visualization of multiple reaction monitoring experiments.

    Martin, Daniel B; Holzman, Ted; May, Damon; Peterson, Amelia; Eastham, Ashley; Eng, Jimmy; McIntosh, Martin

    2008-11-01

    Multiple reaction monitoring (MRM) mass spectrometry identifies and quantifies specific peptides in a complex mixture with very high sensitivity and speed and thus has promise for the high throughput screening of clinical samples for candidate biomarkers. We have developed an interactive software platform, called MRMer, for managing highly complex MRM-MS experiments, including quantitative analyses using heavy/light isotopic peptide pairs. MRMer parses and extracts information from MS files encoded in the platform-independent mzXML data format. It extracts and infers precursor-product ion transition pairings, computes integrated ion intensities, and permits rapid visual curation for analyses exceeding 1000 precursor-product pairs. Results can be easily output for quantitative comparison of consecutive runs. Additionally MRMer incorporates features that permit the quantitative analysis experiments including heavy and light isotopic peptide pairs. MRMer is open source and provided under the Apache 2.0 license.

  19. Stochastic production phase design for an open pit mining complex with multiple processing streams

    Asad, Mohammad Waqar Ali; Dimitrakopoulos, Roussos; van Eldert, Jeroen

    2014-08-01

    In a mining complex, the mine is a source of supply of valuable material (ore) to a number of processes that convert the raw ore to a saleable product or a metal concentrate for production of the refined metal. In this context, expected variation in metal content throughout the extent of the orebody defines the inherent uncertainty in the supply of ore, which impacts the subsequent ore and metal production targets. Traditional optimization methods for designing production phases and ultimate pit limit of an open pit mine not only ignore the uncertainty in metal content, but, in addition, commonly assume that the mine delivers ore to a single processing facility. A stochastic network flow approach is proposed that jointly integrates uncertainty in supply of ore and multiple ore destinations into the development of production phase design and ultimate pit limit. An application at a copper mine demonstrates the intricacies of the new approach. The case study shows a 14% higher discounted cash flow when compared to the traditional approach.

  20. Managing Multiple Sources of Competitive Advantage in a Complex Competitive Environment

    Alexandre Howard Henry Lapersonne

    2013-12-01

    Full Text Available The aim of this article is to review the literature on the topic of sustained and temporary competitive advantage creation, specifically in dynamic markets, and to propose further research possibilities. After having analyzed the main trends and scholars’ works on the subject, it was concluded that a firm which has been experiencing erosion of its core sources of economic rent generation, should have diversified its strategy portfolio in a search for new sources of competitive advantage, ones that could compensate for the decline of profits provoked by intensive competitive environments. This review concludes with the hypothesis that firms, who have decided to enter and manage multiple competitive environments, should have developed a multiple strategies framework approach. The management of this source of competitive advantage portfolio should have allowed persistence of a firm’s superior economic performance through the management of diverse temporary advantages lifecycle and through a resilient effect, where a very successful source of competitive advantage compensates the ones that have been eroded. Additionally, the review indicates that economies of emerging countries, such as the ones from the BRIC block, should present a more complex competitive environment due to their historical nature of cultural diversity, social contrasts and frequent economic disruption, and also because of recent institutional normalization that has turned the market into hypercompetition. Consequently, the study of complex competition should be appropriate in such environments.

  1. Two Wrongs Make a Right: Addressing Underreporting in Binary Data from Multiple Sources.

    Cook, Scott J; Blas, Betsabe; Carroll, Raymond J; Sinha, Samiran

    2017-04-01

    Media-based event data-i.e., data comprised from reporting by media outlets-are widely used in political science research. However, events of interest (e.g., strikes, protests, conflict) are often underreported by these primary and secondary sources, producing incomplete data that risks inconsistency and bias in subsequent analysis. While general strategies exist to help ameliorate this bias, these methods do not make full use of the information often available to researchers. Specifically, much of the event data used in the social sciences is drawn from multiple, overlapping news sources (e.g., Agence France-Presse, Reuters). Therefore, we propose a novel maximum likelihood estimator that corrects for misclassification in data arising from multiple sources. In the most general formulation of our estimator, researchers can specify separate sets of predictors for the true-event model and each of the misclassification models characterizing whether a source fails to report on an event. As such, researchers are able to accurately test theories on both the causes of and reporting on an event of interest. Simulations evidence that our technique regularly out performs current strategies that either neglect misclassification, the unique features of the data-generating process, or both. We also illustrate the utility of this method with a model of repression using the Social Conflict in Africa Database.

  2. Hydrogen Production Costs of Various Primary Energy Sources

    Choi, Jae Hyuk; Tak, Nam Il; Kim, Yong Hee; Park, Won Seok

    2005-01-01

    The limited resource and environmental impacts of fossil fuels are becoming more and more serious problems in the world. Consequently, hydrogen is in the limelight as a future alternative energy due to its clean combustion and inexhaustibility and a transition from the traditional fossil fuel system to a hydrogen-based energy system is under considerations. Several countries are already gearing the industries to the hydrogen economy to cope with the limitations of the current fossil fuels. Unfortunately, hydrogen has to be chemically separated from the hydrogen compounds in nature such as water by using some energy sources. In this paper, the hydrogen production costs of major primary energy sources are compared in consideration of the Korean situations. The evaluation methodology is based on the report of the National Academy of Science (NAS) of U.S

  3. Sealed radioactive sources and method of their production

    Benadik, A.; Tympl, M.; Stopek, K.

    1985-01-01

    The active layer of the proposed sources consists of an inorganic sorbent activated with a radioactive component in form of gel, xerogel or glass. The active particles of the inorganic sorbent have the shape of spheres 2 to 2000 μm in diameter. The sources have a tubular, cylindrical or needle shape and are compact with low leachability. They feature minimal radionuclide leakage, they are reliable and safe. Their production technology is proposed. The inorganic sorbent is put in contact with the sollution of the radioactive compound, then separated from the liquid phase, filled into containers, dried, calcined or sintered or otherwise heat-processed into glass at temperatures of 250 -1800 degC. (M.D.)

  4. Transparent mediation-based access to multiple yeast data sources using an ontology driven interface.

    Briache, Abdelaali; Marrakchi, Kamar; Kerzazi, Amine; Navas-Delgado, Ismael; Rossi Hassani, Badr D; Lairini, Khalid; Aldana-Montes, José F

    2012-01-25

    Saccharomyces cerevisiae is recognized as a model system representing a simple eukaryote whose genome can be easily manipulated. Information solicited by scientists on its biological entities (Proteins, Genes, RNAs...) is scattered within several data sources like SGD, Yeastract, CYGD-MIPS, BioGrid, PhosphoGrid, etc. Because of the heterogeneity of these sources, querying them separately and then manually combining the returned results is a complex and time-consuming task for biologists most of whom are not bioinformatics expert. It also reduces and limits the use that can be made on the available data. To provide transparent and simultaneous access to yeast sources, we have developed YeastMed: an XML and mediator-based system. In this paper, we present our approach in developing this system which takes advantage of SB-KOM to perform the query transformation needed and a set of Data Services to reach the integrated data sources. The system is composed of a set of modules that depend heavily on XML and Semantic Web technologies. User queries are expressed in terms of a domain ontology through a simple form-based web interface. YeastMed is the first mediation-based system specific for integrating yeast data sources. It was conceived mainly to help biologists to find simultaneously relevant data from multiple data sources. It has a biologist-friendly interface easy to use. The system is available at http://www.khaos.uma.es/yeastmed/.

  5. Multiple Spectral Ratio Analyses Reveal Earthquake Source Spectra of Small Earthquakes and Moment Magnitudes of Microearthquakes

    Uchide, T.; Imanishi, K.

    2016-12-01

    Spectral studies for macroscopic earthquake source parameters are helpful for characterizing earthquake rupture process and hence understanding earthquake source physics and fault properties. Those studies require us mute wave propagation path and site effects in spectra of seismograms to accentuate source effect. We have recently developed the multiple spectral ratio method [Uchide and Imanishi, BSSA, 2016] employing many empirical Green's function (EGF) events to reduce errors from the choice of EGF events. This method helps us estimate source spectra more accurately as well as moment ratios among reference and EGF events, which are useful to constrain the seismic moment of microearthquakes. First, we focus on earthquake source spectra. The source spectra have generally been thought to obey the omega-square model with single corner-frequency. However recent studies imply the existence of another corner frequency for some earthquakes. We analyzed small shallow inland earthquakes (3.5 multiple spectral ratio analyses. For 20000 microearthquakes in Fukushima Hamadori and northern Ibaraki prefecture area, we found that the JMA magnitudes (Mj) based on displacement or velocity amplitude are systematically below Mw. The slope of the Mj-Mw relation is 0.5 for Mj 5. We propose a fitting curve for the obtained relationship as Mw = (1/2)Mj + (1/2)(Mjγ + Mcorγ)1/γ+ c, where Mcor is a corner magnitude, γ determines the sharpness of the corner, and c denotes an offset. We obtained Mcor = 4.1, γ = 5.6, and c = -0.47 to fit the observation. The parameters are useful for characterizing the Mj-Mw relationship. This non-linear relationship affects the b-value of the Gutenberg-Richter law. Quantitative discussions on b-values are affected by the definition of magnitude to use.

  6. Managing multiple facets of risk in new product alliances

    Lee, R.P.; Johnson, J.L.

    2010-01-01

    The trend of forming alliances to develop new products continues; however, many of these new product alliances fail. As such we explore how key risk types intrinsic in new product alliances, performance, relational, and knowledge appropriation risks, influence alliance success. Further, we theorize

  7. Modeling Degradation Product Partitioning in Chlorinated-DNAPL Source Zones

    Boroumand, A.; Ramsburg, A.; Christ, J.; Abriola, L.

    2009-12-01

    Metabolic reductive dechlorination degrades aqueous phase contaminant concentrations, increasing the driving force for DNAPL dissolution. Results from laboratory and field investigations suggest that accumulation of cis-dichloroethene (cis-DCE) and vinyl chloride (VC) may occur within DNAPL source zones. The lack of (or slow) degradation of cis-DCE and VC within bioactive DNAPL source zones may result in these dechlorination products becoming distributed among the solid, aqueous, and organic phases. Partitioning of cis-DCE and VC into the organic phase may reduce aqueous phase concentrations of these contaminants and result in the enrichment of these dechlorination products within the non-aqueous phase. Enrichment of degradation products within DNAPL may reduce some of the advantages associated with the application of bioremediation in DNAPL source zones. Thus, it is important to quantify how partitioning (between the aqueous and organic phases) influences the transport of cis-DCE and VC within bioactive DNAPL source zones. In this work, abiotic two-phase (PCE-water) one-dimensional column experiments are modeled using analytical and numerical methods to examine the rate of partitioning and the capacity of PCE-DNAPL to reversibly sequester cis-DCE. These models consider aqueous-phase, nonaqueous phase, and aqueous plus nonaqueous phase mass transfer resistance using linear driving force and spherical diffusion expressions. Model parameters are examined and compared for different experimental conditions to evaluate the mechanisms controlling partitioning. Biot number, a dimensionless number which is an index of the ratio of the aqueous phase mass transfer rate in boundary layer to the mass transfer rate within the NAPL, is used to characterize conditions in which either or both processes are controlling. Results show that application of a single aqueous resistance is capable to capture breakthrough curves when DNAPL is distributed in porous media as low

  8. Marine Vibrionaceae as a source of bioactive natural products

    Månsson, Maria; Wietz, Matthias; Gram, Lone

    an ecological function. Using chemical profiling, vibrio strains were compared on a global scale, revealing that the production of certain compounds is a conserved feature independent of sample locations. Chemical screening techniques such as explorative solid-phase extraction led to the isolation of two novel...... that some strains were capable of producing antibacterial compounds when grown on natural substrates such as chitin or seaweed. One Vibrio coralliilyticus strain was capable of producing the antibacterial compound when using chitin as the sole carbon source and in a live chitin model system, suggesting...... of which possess biological activities attractive for alternative strategies in antibacterial therapy....

  9. Industrialization and production of neutral beam ion sources for MFTF

    Lynch, W.S.

    1981-01-01

    The existing LLNL designs of the 20 and 80kV deuterium fueled Neutral Beam Ion Source Modules (NBSM) have been industrialized and are being produced successfully for the MFTF. Industrialization includes value engineering, production engineering, cost reduction, fixturing, facilitation and procurement of components. Production assembly, inspection and testing is being performed in a large electronics manufacturing plant. Decades of experience in high voltage, high vacuum power tubes is being applied to the procedures and processes. Independent quality and reliability assurance criteria are being utilized. Scheduling of the various engineering, procurement and manufacturing task is performed by the use of a Critical Path Method (CPM) computer code, Innovative, computerized grid alignment methods were also designed and installed specifically for this project. New jointing and cleaning techniques were devised for the NBSMs. Traceability and cost control are also utilized

  10. Marine actinobacteria: an important source of bioactive natural products.

    Manivasagan, Panchanathan; Kang, Kyong-Hwa; Sivakumar, Kannan; Li-Chan, Eunice C Y; Oh, Hyun-Myung; Kim, Se-Kwon

    2014-07-01

    Marine environment is largely an untapped source for deriving actinobacteria, having potential to produce novel, bioactive natural products. Actinobacteria are the prolific producers of pharmaceutically active secondary metabolites, accounting for about 70% of the naturally derived compounds that are currently in clinical use. Among the various actinobacterial genera, Actinomadura, Actinoplanes, Amycolatopsis, Marinispora, Micromonospora, Nocardiopsis, Saccharopolyspora, Salinispora, Streptomyces and Verrucosispora are the major potential producers of commercially important bioactive natural products. In this respect, Streptomyces ranks first with a large number of bioactive natural products. Marine actinobacteria are unique enhancing quite different biological properties including antimicrobial, anticancer, antiviral, insecticidal and enzyme inhibitory activities. They have attracted global in the last ten years for their ability to produce pharmaceutically active compounds. In this review, we have focused attention on the bioactive natural products isolated from marine actinobacteria, possessing unique chemical structures that may form the basis for synthesis of novel drugs that could be used to combat resistant pathogenic microorganisms. Copyright © 2014 Elsevier B.V. All rights reserved.

  11. The metal-organic framework MIL-53(Al) constructed from multiple metal sources: alumina, aluminum hydroxide, and boehmite.

    Li, Zehua; Wu, Yi-nan; Li, Jie; Zhang, Yiming; Zou, Xin; Li, Fengting

    2015-04-27

    Three aluminum compounds, namely alumina, aluminum hydroxide, and boehmite, are probed as the metal sources for the hydrothermal synthesis of a typical metal-organic framework MIL-53(Al). The process exhibits enhanced synthetic efficiency without the generation of strongly acidic byproducts. The time-course monitoring of conversion from different aluminum sources into MIL-53(Al) is achieved by multiple characterization that reveals a similar but differentiated crystallinity, porosity, and morphology relative to typical MIL-53(Al) prepared from water-soluble aluminum salts. Moreover, the prepared MIL-53(Al) constructed with the three insoluble aluminum sources exhibit an improved thermal stability of up to nearly 600 °C and enhanced yields. Alumina and boehmite are more preferable than aluminum hydroxide in terms of product porosity, yield, and reaction time. The adsorption performances of a typical environmental endocrine disruptor, dimethyl phthalate, on the prepared MIL-53(Al) samples are also investigated. The improved structural stability of MIL-53(Al) prepared from these alternative aluminum sources enables double-enhanced adsorption performance (up to 206 mg g(-1)) relative to the conventionally obtained MIL-53(Al). © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  12. MULTIPLE CRITERIA DECISION MAKING IN STRATEGIC PLANNING OF TABLE EGG PRODUCTION

    Ana Crnčan

    2016-06-01

    Full Text Available The main research objective was to analyze and evaluate different systems of table egg production by using the multiple criteria analysis, the method of Analytic Hierarchy Process (AHP in decision making within strategic planning of production. The survey involved 79 producers of table eggs registered in the Records on laying hens’ farms in the Republic of Croatia. In the first stage, the research defined the criteria and sub-criteria for system evaluation which were compared in pairs in order to determine the weight or importance for each of them. Alternatives were evaluation based on definition of priorities of examinees and the extent to which they meet each of the defined criteria and sub-criteria. Intensity of examinees’ preferences were entered into the Expert Choice software in order to evaluate ranking results of egg production systems. Defined model consisted of a quantitative criterion of economic indicators, and the other two referred to qualitative criteria, market indicators and technical-technological factors. Each criterion had its corresponding sub-criteria that were evenly distributed in numerical order. Based on individual assessments of the examinees, overall cumulative evaluation was obtained for the table egg production systems. Accordingly, the most acceptable alternative to egg production is the indoor keeping system (priority 0.301. It is followed by the free-range system of keeping laying hens (priority 0.253. The third-ranked alternative is egg production by hens kept in conventional cages (priority 0.226, while the fourth-ranked least acceptable alternative, as of the total evaluation, is the ecological system of egg production (priority 0.220. Taking into account the obtained results of multiple criteria evaluation as well as EU and world trends in changing consumers’ habits including food safety and quality as well as customers’ preferences towards local market and local products, it is recommended that eggs

  13. Multiple production of hadrons in deep-inelastic processes

    Kiselev, A.V.; Petrov, V.A.

    1984-01-01

    A formula to describe an average hadron multiplicity on deep-inelastic processes has been proposed. On the basis of available experimental data predictions are made about the behaviour of average multiplicity at higher energies. The W-dependence of obserVed in experiments at present remains invariable up to energies W approximately 20-25 GeV. At W> or approXimately 25 GeV there will begin a rapid ibcrease of , which is analogous to the increase, observed for sub(esup(+)esup(-)) and is of the same nature

  14. Accounting for multiple sources of uncertainty in impact assessments: The example of the BRACE study

    O'Neill, B. C.

    2015-12-01

    Assessing climate change impacts often requires the use of multiple scenarios, types of models, and data sources, leading to a large number of potential sources of uncertainty. For example, a single study might require a choice of a forcing scenario, climate model, bias correction and/or downscaling method, societal development scenario, model (typically several) for quantifying elements of societal development such as economic and population growth, biophysical model (such as for crop yields or hydrology), and societal impact model (e.g. economic or health model). Some sources of uncertainty are reduced or eliminated by the framing of the question. For example, it may be useful to ask what an impact outcome would be conditional on a given societal development pathway, forcing scenario, or policy. However many sources of uncertainty remain, and it is rare for all or even most of these sources to be accounted for. I use the example of a recent integrated project on the Benefits of Reduced Anthropogenic Climate changE (BRACE) to explore useful approaches to uncertainty across multiple components of an impact assessment. BRACE comprises 23 papers that assess the differences in impacts between two alternative climate futures: those associated with Representative Concentration Pathways (RCPs) 4.5 and 8.5. It quantifies difference in impacts in terms of extreme events, health, agriculture, tropical cyclones, and sea level rise. Methodologically, it includes climate modeling, statistical analysis, integrated assessment modeling, and sector-specific impact modeling. It employs alternative scenarios of both radiative forcing and societal development, but generally uses a single climate model (CESM), partially accounting for climate uncertainty by drawing heavily on large initial condition ensembles. Strengths and weaknesses of the approach to uncertainty in BRACE are assessed. Options under consideration for improving the approach include the use of perturbed physics

  15. Medical Isotope Production Analyses In KIPT Neutron Source Facility

    Talamo, Alberto; Gohar, Yousry

    2016-01-01

    Medical isotope production analyses in Kharkov Institute of Physics and Technology (KIPT) neutron source facility were performed to include the details of the irradiation cassette and the self-shielding effect. An updated detailed model of the facility was used for the analyses. The facility consists of an accelerator-driven system (ADS), which has a subcritical assembly using low-enriched uranium fuel elements with a beryllium-graphite reflector. The beryllium assemblies of the reflector have the same outer geometry as the fuel elements, which permits loading the subcritical assembly with different number of fuel elements without impacting the reflector performance. The subcritical assembly is driven by an external neutron source generated from the interaction of 100-kW electron beam with a tungsten target. The facility construction was completed at the end of 2015, and it is planned to start the operation during the year of 2016. It is the first ADS in the world, which has a coolant system for removing the generated fission power. Argonne National Laboratory has developed the design concept and performed extensive design analyses for the facility including its utilization for the production of different radioactive medical isotopes. 99 Mo is the parent isotope of 99m Tc, which is the most commonly used medical radioactive isotope. Detailed analyses were performed to define the optimal sample irradiation location and the generated activity, for several radioactive medical isotopes, as a function of the irradiation time.

  16. Medical Isotope Production Analyses In KIPT Neutron Source Facility

    Talamo, Alberto [Argonne National Lab. (ANL), Argonne, IL (United States); Gohar, Yousry [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-01-01

    Medical isotope production analyses in Kharkov Institute of Physics and Technology (KIPT) neutron source facility were performed to include the details of the irradiation cassette and the self-shielding effect. An updated detailed model of the facility was used for the analyses. The facility consists of an accelerator-driven system (ADS), which has a subcritical assembly using low-enriched uranium fuel elements with a beryllium-graphite reflector. The beryllium assemblies of the reflector have the same outer geometry as the fuel elements, which permits loading the subcritical assembly with different number of fuel elements without impacting the reflector performance. The subcritical assembly is driven by an external neutron source generated from the interaction of 100-kW electron beam with a tungsten target. The facility construction was completed at the end of 2015, and it is planned to start the operation during the year of 2016. It is the first ADS in the world, which has a coolant system for removing the generated fission power. Argonne National Laboratory has developed the design concept and performed extensive design analyses for the facility including its utilization for the production of different radioactive medical isotopes. 99Mo is the parent isotope of 99mTc, which is the most commonly used medical radioactive isotope. Detailed analyses were performed to define the optimal sample irradiation location and the generated activity, for several radioactive medical isotopes, as a function of the irradiation time.

  17. An efficient central DOA tracking algorithm for multiple incoherently distributed sources

    Hassen, Sonia Ben; Samet, Abdelaziz

    2015-12-01

    In this paper, we develop a new tracking method for the direction of arrival (DOA) parameters assuming multiple incoherently distributed (ID) sources. The new approach is based on a simple covariance fitting optimization technique exploiting the central and noncentral moments of the source angular power densities to estimate the central DOAs. The current estimates are treated as measurements provided to the Kalman filter that model the dynamic property of directional changes for the moving sources. Then, the covariance-fitting-based algorithm and the Kalman filtering theory are combined to formulate an adaptive tracking algorithm. Our algorithm is compared to the fast approximated power iteration-total least square-estimation of signal parameters via rotational invariance technique (FAPI-TLS-ESPRIT) algorithm using the TLS-ESPRIT method and the subspace updating via FAPI-algorithm. It will be shown that the proposed algorithm offers an excellent DOA tracking performance and outperforms the FAPI-TLS-ESPRIT method especially at low signal-to-noise ratio (SNR) values. Moreover, the performances of the two methods increase as the SNR values increase. This increase is more prominent with the FAPI-TLS-ESPRIT method. However, their performances degrade when the number of sources increases. It will be also proved that our method depends on the form of the angular distribution function when tracking the central DOAs. Finally, it will be shown that the more the sources are spaced, the more the proposed method can exactly track the DOAs.

  18. Interpolating between random walks and optimal transportation routes: Flow with multiple sources and targets

    Guex, Guillaume

    2016-05-01

    In recent articles about graphs, different models proposed a formalism to find a type of path between two nodes, the source and the target, at crossroads between the shortest-path and the random-walk path. These models include a freely adjustable parameter, allowing to tune the behavior of the path toward randomized movements or direct routes. This article presents a natural generalization of these models, namely a model with multiple sources and targets. In this context, source nodes can be viewed as locations with a supply of a certain good (e.g. people, money, information) and target nodes as locations with a demand of the same good. An algorithm is constructed to display the flow of goods in the network between sources and targets. With again a freely adjustable parameter, this flow can be tuned to follow routes of minimum cost, thus displaying the flow in the context of the optimal transportation problem or, by contrast, a random flow, known to be similar to the electrical current flow if the random-walk is reversible. Moreover, a source-targetcoupling can be retrieved from this flow, offering an optimal assignment to the transportation problem. This algorithm is described in the first part of this article and then illustrated with case studies.

  19. Differentiating between anthropogenic and geological sources of nitrate using multiple geochemical tracers

    Linhoff, B.; Norton, S.; Travis, R.; Romero, Z.; Waters, B.

    2017-12-01

    Nitrate contamination of groundwater is a major problem globally including within the Albuquerque Basin in New Mexico. Ingesting high concentrations of nitrate (> 10 mg/L as N) can lead to an increased risk of cancer and to methemoglobinemia in infants. Numerous anthropogenic sources of nitrate have been identified within the Albuquerque Basin including fertilizers, landfills, multiple sewer pipe releases, sewer lagoons, domestic septic leach fields, and a nitric acid line outfall. Furthermore, groundwater near ephemeral streams often exhibits elevated NO3 concentrations and high NO3/Cl ratios incongruous with an anthropogenic source. These results suggest that NO3 can be concentrated through evaporation beneath ephemeral streams and mobilized via irrigation or land use change. This study seeks to use extensive geochemical analyses of groundwater and surface water to differentiate between various sources of NO3 contamination. The U.S. Geological Survey collected 54 groundwater samples from wells and six samples from ephemeral streams from within and from outside of areas of known nitrate contamination. To fingerprint the sources of nitrate pollution, samples were analyzed for major ions, trace metals, nutrients, dissolved gases, δ15N and δ18O in NO3, δ15N within N2 gas, and, δ2H and δ18O in H2O. Furthermore, most sites were sampled for artificial sweeteners and numerous contaminants of emerging concern including pharmaceutical drugs, caffeine, and wastewater indicators. This study will also investigate the age distribution of groundwater and the approximate age of anthropogenic NO3 contamination using 3He/4He, δ13C, 14C, 3H, as well as pharmaceutical drugs and artificial sweeteners with known patent and U.S. Food and Drug Administration approval dates. This broad suite of analytes will be used to differentiate between naturally occurring and multiple anthropogenic NO3 sources, and to potentially determine the approximate date of NO3 contamination.

  20. Validation and calibration of structural models that combine information from multiple sources.

    Dahabreh, Issa J; Wong, John B; Trikalinos, Thomas A

    2017-02-01

    Mathematical models that attempt to capture structural relationships between their components and combine information from multiple sources are increasingly used in medicine. Areas covered: We provide an overview of methods for model validation and calibration and survey studies comparing alternative approaches. Expert commentary: Model validation entails a confrontation of models with data, background knowledge, and other models, and can inform judgments about model credibility. Calibration involves selecting parameter values to improve the agreement of model outputs with data. When the goal of modeling is quantitative inference on the effects of interventions or forecasting, calibration can be viewed as estimation. This view clarifies issues related to parameter identifiability and facilitates formal model validation and the examination of consistency among different sources of information. In contrast, when the goal of modeling is the generation of qualitative insights about the modeled phenomenon, calibration is a rather informal process for selecting inputs that result in model behavior that roughly reproduces select aspects of the modeled phenomenon and cannot be equated to an estimation procedure. Current empirical research on validation and calibration methods consists primarily of methodological appraisals or case-studies of alternative techniques and cannot address the numerous complex and multifaceted methodological decisions that modelers must make. Further research is needed on different approaches for developing and validating complex models that combine evidence from multiple sources.

  1. Glutathione provides a source of cysteine essential for intracellular multiplication of Francisella tularensis.

    Khaled Alkhuder

    2009-01-01

    Full Text Available Francisella tularensis is a highly infectious bacterium causing the zoonotic disease tularemia. Its ability to multiply and survive in macrophages is critical for its virulence. By screening a bank of HimarFT transposon mutants of the F. tularensis live vaccine strain (LVS to isolate intracellular growth-deficient mutants, we selected one mutant in a gene encoding a putative gamma-glutamyl transpeptidase (GGT. This gene (FTL_0766 was hence designated ggt. The mutant strain showed impaired intracellular multiplication and was strongly attenuated for virulence in mice. Here we present evidence that the GGT activity of F. tularensis allows utilization of glutathione (GSH, gamma-glutamyl-cysteinyl-glycine and gamma-glutamyl-cysteine dipeptide as cysteine sources to ensure intracellular growth. This is the first demonstration of the essential role of a nutrient acquisition system in the intracellular multiplication of F. tularensis. GSH is the most abundant source of cysteine in the host cytosol. Thus, the capacity this intracellular bacterial pathogen has evolved to utilize the available GSH, as a source of cysteine in the host cytosol, constitutes a paradigm of bacteria-host adaptation.

  2. Subcritical Neutron Multiplication Measurements of HEU Using Delayed Neutrons as the Driving Source

    Hollas, C.L.; Goulding, C.A.; Myers, W.L.

    1999-01-01

    A new method for the determination of the multiplication of highly enriched uranium systems is presented. The method uses delayed neutrons to drive the HEU system. These delayed neutrons are from fission events induced by a pulsed 14-MeV neutron source. Between pulses, neutrons are detected within a medium efficiency neutron detector using 3 He ionization tubes within polyethylene enclosures. The neutron detection times are recorded relative to the initiation of the 14-MeV neutron pulse, and subsequently analyzed with the Feynman reduced variance method to extract singles, doubles and triples neutron counting rates. Measurements have been made on a set of nested hollow spheres of 93% enriched uranium, with mass values from 3.86 kg to 21.48 kg. The singles, doubles and triples counting rates for each uranium system are compared to calculations from point kinetics models of neutron multiplicity to assign multiplication values. These multiplication values are compared to those from MC NP K-Code calculations

  3. Evaluation of MODIS NPP and GPP products across multiple biomes.

    David P. Turner; William D. Ritts; Warren B. Cohen; Stith T. Gower; Steve W. Running; Maosheng Zhao; Marcos H. Costa; Al A. Kirschbaum; Jay M. Ham; Scott R. Saleska; Douglas E. Ahl

    2006-01-01

    Estimates of daily gross primary production (GPP) and annual net primary production (NPP) at the 1 km spatial resolution are now produced operationally for the global terrestrial surface using imagery from the MODIS (Moderate Resolution Imaging Spectroradiometer) sensor. Ecosystem-level measurements of GPP at eddy covariance flux towers and plot-level measurements of...

  4. Development of repository-wide radionuclide transport model considering the effects of multiple sources

    Hatanaka, Koichiro; Watari, Shingo; Ijiri, Yuji

    1999-11-01

    Safety assessment of the geological isolation system according to the groundwater scenario has traditionally been conducted based on the signal canister configuration and then the safety of total system has been evaluated based on the dose rates which were obtained by multiplying the migration rates released from the engineered barrier and/or the natural barrier by dose conversion factors and total number of canisters disposed in the repository. The dose conversion factors can be obtained from the biosphere analysis. In this study, we focused on the effect of multiple sources due to the disposal of canisters at different positions in the repository. By taking the effect of multiple sources into consideration, concentration interference in the repository region is possible to take place. Therefore, radionuclide transport model/code considering the effect of concentration interference due to the multiple sources was developed to make assessments of the effect quantitatively. The newly developed model/code was verified through the comparison analysis with the existing radionuclide transport analysis code used in the second progress report. In addition, the effect of the concentration interference was evaluated by setting a simple problem using the newly developed analysis code. This results shows that the maximum park value of the migration rates from the repository was about two orders of magnitude lower than that based on single canister configuration. Since the analysis code was developed by assuming that all canisters disposed of along the one-dimensional groundwater flow contribute to the concentration interference in the repository region, the assumption should be verified by conducting two or three-dimensional analysis considering heterogeneous geological structure as a future work. (author)

  5. Exclusive description of multiple production on nuclei in the additive quark model. Multiplicity distributions in interactions with heavy nuclei

    Levchenko, B.B.; Nikolaev, N.N.

    1985-01-01

    In the framework of the additive quark model of multiple production on nuclei we calculate the multiplicity distributions of secondary particles and the correlations between secondary particles in πA and pA interactions with heavy nuclei. We show that intranuclear cascades are responsible for up to 50% of the nuclear increase of the multiplicity of fast particles. We analyze the sensitivity of the multiplicities and their correlations to the choice of the quark-hadronization function. We show that with good accuracy the yield of relativistic secondary particles from heavy and intermediate nuclei depends only on the number N/sub p/ of protons knocked out of the nucleus, and not on the mass number of the nucleus (N/sub p/ scaling)

  6. Combining multiple ecosystem productivity measurements to constrain carbon uptake estimates in semiarid grasslands and shrublands

    Maurer, G. E.; Krofcheck, D. J.; Collins, S. L.; Litvak, M. E.

    2016-12-01

    Recent observational and modeling studies have indicated that semiarid ecosystems are more dynamic contributors to the global carbon budget than once thought. Semiarid carbon fluxes, however, are generally small, with high interannual and spatial variability, which suggests that validating their global significance may depend on examining multiple productivity measures and their associated uncertainties and inconsistencies. We examined ecosystem productivity from eddy covariance (NEE), harvest (NPP), and terrestrial biome models (NEPm) at two very similar grassland sites and one creosote shrubland site in the Sevilleta National Wildlife Refuge of central New Mexico, USA. Our goal was to assess site and methodological correspondence in annual carbon uptake, patterns of interannual variability, and measurement uncertainty. One grassland site was a perennial carbon source losing 30 g C m-2 per year on average, while the other two sites were carbon sources or sinks depending on the year, with average net uptake of 5 and 25 g C m-2 per year at the grassland and shrubland site, respectively. Uncertainty values for cumulative annual NEE overlapped between the three sites in most years. When combined, aboveground and belowground annual NPP measurements were 15% higher than annual NEE values and did not confirm a loss of carbon at any site in any year. Despite differences in mean site carbon balance, year-to-year changes in cumulative annual NEE and NPP were similar at all sites with years 2010 and 2013 being favorable for carbon uptake and 2011 and 2012 being unfavorable at all sites. Modeled NEPm data for a number of nearby grid cells reproduced only a fraction of the observed range in carbon uptake and its interannual variability. These three sites are highly similar in location and climate and multiple carbon flux measurements confirm the high interannual variability in carbon flux. The exact magnitude of these fluxes, however, remains difficult to discern.

  7. Geothermal source potential and utilization for alcohol production

    Austin, J.C.

    1981-11-01

    A study was conducted to assess the technical and economic feasibility of using a potential geothermal source to drive a fuel grade alcohol plant. Test data from the well at the site indicated that the water temperature at approximately 8500 feet should approach 275/sup 0/F. However, no flow data was available, and so the volume of hot water that can be expected from a well at this site is unknown. Using the available data, numerous fuel alcohol production processes and various heat utilization schemes were investigated to determine the most cost effective system for using the geothermal resource. The study found the direct application of hot water for alcohol production based on atmospheric processes using low pressure steam to be most cost effective. The geothermal flow rates were determined for various sizes of alcohol production facility using 275/sup 0/F water, 235/sup 0/F maximum processing temperature, 31,000 and 53,000 Btu per gallon energy requirements, and appropriate process approach temperatures. It was determined that a 3 million gpy alcohol plant is the largest facility that can practically be powered by the flow from one large geothermal well. An order-of-magnitude cost estimate was prepared, operating costs were calculated, the economic feasibility of the propsed project was examined, and a sensitivity analysis was performed.

  8. Microbial production of poly(hydroxybutyrate) from C₁ carbon sources.

    Khosravi-Darani, Kianoush; Mokhtari, Zahra-Beigom; Amai, Tomohito; Tanaka, Kenji

    2013-02-01

    Polyhydroxybutyrate (PHB) is an attractive substitute for petrochemical plastic due to its similar properties, biocompatibility, and biodegradability. The cost of scaled-up PHB production inhibits its widespread usage. Intensive researches are growing to reduce costs and improve thermomechanical, physical, and processing properties of this green biopolymer. Among cheap substrates which are used for reducing total cost of PHB production, some C₁ carbon sources, e.g., methane, methanol, and CO₂ have received a great deal of attention due to their serious role in greenhouse problem. This article reviews the fundamentals of strategies for reducing PHA production and moves on to the applications of several cheap substrates with a special emphasis on methane, methanol, and CO₂. Also, some explanation for involved microorganisms including the hydrogen-oxidizing bacteria and methanotrophs, their history, culture condition, and nutritional requirements are given. After description of some important strains among the hydrogen-oxidizing and methanotrophic producers of PHB, the article is focused on limitations, threats, and opportunities for application and their future trends.

  9. Relaxation dynamics in the presence of pulse multiplicative noise sources with different correlation properties

    Kargovsky, A. V.; Chichigina, O. A.; Anashkina, E. I.; Valenti, D.; Spagnolo, B.

    2015-10-01

    The relaxation dynamics of a system described by a Langevin equation with pulse multiplicative noise sources with different correlation properties is considered. The solution of the corresponding Fokker-Planck equation is derived for Gaussian white noise. Moreover, two pulse processes with regulated periodicity are considered as a noise source: the dead-time-distorted Poisson process and the process with fixed time intervals, which is characterized by an infinite correlation time. We find that the steady state of the system is dependent on the correlation properties of the pulse noise. An increase of the noise correlation causes the decrease of the mean value of the solution at the steady state. The analytical results are in good agreement with the numerical ones.

  10. System and method for integrating and accessing multiple data sources within a data warehouse architecture

    Musick, Charles R [Castro Valley, CA; Critchlow, Terence [Livermore, CA; Ganesh, Madhaven [San Jose, CA; Slezak, Tom [Livermore, CA; Fidelis, Krzysztof [Brentwood, CA

    2006-12-19

    A system and method is disclosed for integrating and accessing multiple data sources within a data warehouse architecture. The metadata formed by the present method provide a way to declaratively present domain specific knowledge, obtained by analyzing data sources, in a consistent and useable way. Four types of information are represented by the metadata: abstract concepts, databases, transformations and mappings. A mediator generator automatically generates data management computer code based on the metadata. The resulting code defines a translation library and a mediator class. The translation library provides a data representation for domain specific knowledge represented in a data warehouse, including "get" and "set" methods for attributes that call transformation methods and derive a value of an attribute if it is missing. The mediator class defines methods that take "distinguished" high-level objects as input and traverse their data structures and enter information into the data warehouse.

  11. Prediction of the neutrons subcritical multiplication using the diffusion hybrid equation with external neutron sources

    Costa da Silva, Adilson; Carvalho da Silva, Fernando [COPPE/UFRJ, Programa de Engenharia Nuclear, Caixa Postal 68509, 21941-914, Rio de Janeiro (Brazil); Senra Martinez, Aquilino, E-mail: aquilino@lmp.ufrj.br [COPPE/UFRJ, Programa de Engenharia Nuclear, Caixa Postal 68509, 21941-914, Rio de Janeiro (Brazil)

    2011-07-15

    Highlights: > We proposed a new neutron diffusion hybrid equation with external neutron source. > A coarse mesh finite difference method for the adjoint flux and reactivity calculation was developed. > 1/M curve to predict the criticality condition is used. - Abstract: We used the neutron diffusion hybrid equation, in cartesian geometry with external neutron sources to predict the subcritical multiplication of neutrons in a pressurized water reactor, using a 1/M curve to predict the criticality condition. A Coarse Mesh Finite Difference Method was developed for the adjoint flux calculation and to obtain the reactivity values of the reactor. The results obtained were compared with benchmark values in order to validate the methodology presented in this paper.

  12. Prediction of the neutrons subcritical multiplication using the diffusion hybrid equation with external neutron sources

    Costa da Silva, Adilson; Carvalho da Silva, Fernando; Senra Martinez, Aquilino

    2011-01-01

    Highlights: → We proposed a new neutron diffusion hybrid equation with external neutron source. → A coarse mesh finite difference method for the adjoint flux and reactivity calculation was developed. → 1/M curve to predict the criticality condition is used. - Abstract: We used the neutron diffusion hybrid equation, in cartesian geometry with external neutron sources to predict the subcritical multiplication of neutrons in a pressurized water reactor, using a 1/M curve to predict the criticality condition. A Coarse Mesh Finite Difference Method was developed for the adjoint flux calculation and to obtain the reactivity values of the reactor. The results obtained were compared with benchmark values in order to validate the methodology presented in this paper.

  13. An open-source software program for performing Bonferroni and related corrections for multiple comparisons

    Kyle Lesack

    2011-01-01

    Full Text Available Increased type I error resulting from multiple statistical comparisons remains a common problem in the scientific literature. This may result in the reporting and promulgation of spurious findings. One approach to this problem is to correct groups of P-values for "family-wide significance" using a Bonferroni correction or the less conservative Bonferroni-Holm correction or to correct for the "false discovery rate" with a Benjamini-Hochberg correction. Although several solutions are available for performing this correction through commercially available software there are no widely available easy to use open source programs to perform these calculations. In this paper we present an open source program written in Python 3.2 that performs calculations for standard Bonferroni, Bonferroni-Holm and Benjamini-Hochberg corrections.

  14. Joint source based analysis of multiple brain structures in studying major depressive disorder

    Ramezani, Mahdi; Rasoulian, Abtin; Hollenstein, Tom; Harkness, Kate; Johnsrude, Ingrid; Abolmaesumi, Purang

    2014-03-01

    We propose a joint Source-Based Analysis (jSBA) framework to identify brain structural variations in patients with Major Depressive Disorder (MDD). In this framework, features representing position, orientation and size (i.e. pose), shape, and local tissue composition are extracted. Subsequently, simultaneous analysis of these features within a joint analysis method is performed to generate the basis sources that show signi cant di erences between subjects with MDD and those in healthy control. Moreover, in a cross-validation leave- one-out experiment, we use a Fisher Linear Discriminant (FLD) classi er to identify individuals within the MDD group. Results show that we can classify the MDD subjects with an accuracy of 76% solely based on the information gathered from the joint analysis of pose, shape, and tissue composition in multiple brain structures.

  15. On the possibility of the multiple inductively coupled plasma and helicon plasma sources for large-area processes

    Lee, Jin-Won; Lee, Yun-Seong, E-mail: leeeeys@kaist.ac.kr; Chang, Hong-Young [Low-temperature Plasma Laboratory, Department of Physics, Korea Advanced Institute of Science and Technology, Daejeon 305-701 (Korea, Republic of); An, Sang-Hyuk [Agency of Defense Development, Yuseong-gu, Daejeon 305-151 (Korea, Republic of)

    2014-08-15

    In this study, we attempted to determine the possibility of multiple inductively coupled plasma (ICP) and helicon plasma sources for large-area processes. Experiments were performed with the one and two coils to measure plasma and electrical parameters, and a circuit simulation was performed to measure the current at each coil in the 2-coil experiment. Based on the result, we could determine the possibility of multiple ICP sources due to a direct change of impedance due to current and saturation of impedance due to the skin-depth effect. However, a helicon plasma source is difficult to adapt to the multiple sources due to the consistent change of real impedance due to mode transition and the low uniformity of the B-field confinement. As a result, it is expected that ICP can be adapted to multiple sources for large-area processes.

  16. Shape optimization of an airfoil in a BZT flow with multiple-source uncertainties

    Congedo, P.M.; Corre, C.; Martinez, J.M.

    2011-01-01

    Bethe-Zel'dovich-Thompson fluids (BZT) are characterized by negative values of the fundamental derivative of gas dynamics for a range of temperatures and pressures in the vapor phase, which leads to non-classical gas dynamic behaviors such as the disintegration of compression shocks. These non-classical phenomena can be exploited, when using these fluids in Organic Rankine Cycles (ORCs), to increase isentropic efficiency. A predictive numerical simulation of these flows must account for two main sources of physical uncertainties: the BZT fluid properties often difficult to measure accurately and the usually fluctuating turbine inlet conditions. For taking full advantage of the BZT properties, the turbine geometry must also be specifically designed, keeping in mind the geometry achieved in practice after machining always slightly differs from the theoretical shape. This paper investigates some efficient procedures to perform shape optimization in a 2D BZT flow with multiple-source uncertainties (thermodynamic model, operating conditions and geometry). To demonstrate the feasibility of the proposed efficient strategies for shape optimization in the presence of multiple-source uncertainties, a zero incidence symmetric airfoil wave-drag minimization problem is retained as a case-study. This simplified configuration encompasses most of the features associated with a turbine design problem, as far the uncertainty quantification is concerned. A preliminary analysis of the contributions to the variance of the wave-drag allows to select the most significant sources of uncertainties using a reduced number of flow computations. The resulting mean value and variance of the objective are next turned into meta models. The optimal Pareto sets corresponding to the minimization of various substitute functions are obtained using a genetic algorithm as optimizer and their differences are discussed. (authors)

  17. Assessment of factors which affect multiple uses of water sources at household level in rural Zimbabwe - A case study of Marondera, Murehwa and Uzumba Maramba Pfungwe districts

    Katsi, Luckson; Siwadi, Japson; Guzha, Edward; Makoni, Fungai S.; Smits, Stef

    Water with all its multiple uses plays a pivotal role in the sustenance of rural livelihoods, especially the poor. As such, the provision of water which go beyond domestic to include water for small-scale productive uses should be encouraged to enhance peoples’ livelihood options by making significant contribution to household income, food security, improved nutrition and health. All these multiple benefits, if combined can assist in the fight against hunger and poverty. This study was conducted in Mashonaland East province, covering Marondera, Murehwa and Uzumba Maramba Pfungwe districts in Zimbabwe for the period December 2005-May 2006 to assess factors which affect multiple uses of water sources at household level. Participatory Rural Appraisal tools such as discussions, observations and interviews were used for data collection. The survey found that people indeed require water for productive purposes apart from domestic uses, which are often given top priority. The study found out that multiple uses of water sources at household level can be affected by segmentation of water services into domestic and productive water supply schemes, technology and system design, water quality and quantity and distance to water sources among other factors. The study recommends that water service providers to be able to provide appropriate, efficient and sustainable services, they should understand and appreciate that people’s water needs are integrated and are part and parcel of their multifaceted livelihood strategies.

  18. Tensor rank is not multiplicative under the tensor product

    M. Christandl (Matthias); A. K. Jensen (Asger Kjærulff); J. Zuiddam (Jeroen)

    2017-01-01

    textabstractThe tensor rank of a tensor is the smallest number r such that the tensor can be decomposed as a sum of r simple tensors. Let s be a k-tensor and let t be an l-tensor. The tensor product of s and t is a (k + l)-tensor (not to be confused with the "tensor Kronecker product" used in

  19. Basalt generation at the Apollo 12 site. Part 2: Source heterogeneity, multiple melts, and crustal contamination

    Neal, Clive R.; Hacker, Matthew D.; Snyder, Gregory A.; Taylor, Lawrence A.; Liu, Yun-Gang; Schmitt, Roman A.

    1994-01-01

    The petrogenesis of Apollo 12 mare basalts has been examined with emphasis on trace-element ratios and abundances. Vitrophyric basalts were used as parental compositions for the modeling, and proportions of fractionating phases were determined using the MAGFOX prograqm of Longhi (1991). Crystal fractionation processes within crustal and sub-crustal magma chambers are evaluated as a function of pressure. Knowledge of the fractionating phases allows trace-element variations to be considered as either source related or as a product of post-magma-generation processes. For the ilmenite and olivine basalts, trace-element variations are inherited from the source, but the pigeonite basalt data have been interpreted with open-system evolution processes through crustal assimilation. Three groups of basalts have been examined: (1) Pigeonite basalts-produced by the assimilation of lunar crustal material by a parental melt (up to 3% assimilation and 10% crystal fractionation, with an 'r' value of 0.3). (2) Ilmenite basalts-produced by variable degrees of partial melting (4-8%) of a source of olivine, pigeonite, augite, and plagioclase, brought together by overturn of the Lunar Magma Ocean (LMO) cumulate pile. After generation, which did not exhaust any of the minerals in the source, these melts experienced closed-system crystal fractionation/accumulation. (3) Olivine basalts-produced by variable degrees of partial melting (5-10%) of a source of olivine, pigeonite, and augite. After generation, again without exhausting any of the minerals in the source, these melts evolved through crystal accumulation. The evolved liquid counterparts of these cumulates have not been sampled. The source compositions for the ilmenite and olivine basalts were calculated by assuming that the vitrophyric compositions were primary and the magmas were produced by non-modal batch melting. Although the magnitude is unclear, evaluation of these source regions indicates that both be composed of early- and

  20. Use of multiple data sources to estimate hepatitis C seroprevalence among prisoners: A retrospective cohort study.

    Kathryn J Snow

    Full Text Available Hepatitis C is a major cause of preventable morbidity and mortality. Prisoners are a key population for hepatitis C control programs, and with the advent of highly effective therapies, prisons are increasingly important sites for hepatitis C diagnosis and treatment. Accurate estimates of hepatitis C prevalence among prisoners are needed in order to plan and resource service provision, however many prevalence estimates are based on surveys compromised by limited and potentially biased participation. We aimed to compare estimates derived from three different data sources, and to assess whether the use of self-report as a supplementary data source may help researchers assess the risk of selection bias. We used three data sources to estimate the prevalence of hepatitis C antibodies in a large cohort of Australian prisoners-prison medical records, self-reported status during a face-to-face interview prior to release from prison, and data from a statewide notifiable conditions surveillance system. Of 1,315 participants, 33.8% had at least one indicator of hepatitis C seropositivity, however less than one third of these (9.5% of the entire cohort were identified by all three data sources. Among participants of known status, self-report had a sensitivity of 80.1% and a positive predictive value of 97.8%. Any one data source used in isolation would have under-estimated the prevalence of hepatitis C in this cohort. Using multiple data sources in studies of hepatitis C seroprevalence among prisoners may improve case detection and help researchers assess the risk of selection bias due to non-participation in serological testing.

  1. Design and production of activimeters verification sealed radioactive sources

    Serra, R.; Hernandez Rivero, A. T.; Oropesa, P.; Rapado, M.; Falcon, L.

    2006-01-01

    Measurement in a radionuclide calibrator (activimeter) of the doses to be administered to a patient for diagnosis or radiotherapeutic treatment is an essential element in Nuclear Medicine practice. To assure that patient will receive the optimal doses that guarantee the necessary quality of the image to be studied or optimum radiotherapeutic effect, the activity determination should fulfil established accuracy requirements. To this aim, the overall uncertainty in activity determination must not surpass a preestablished limit of about 10 % for the expanded uncertainty of the activity value (with a coverage factor k = 3). To have suitable equipment, periodically calibrated for specialized and authorized specialists and frequently verified in inter calibration periods to guarantee detection of any malfunctioning, are essential requirements to assure the compliance with the prescribed regulations and limiting values. This paper describes the design and production of two models of 137 Cs activimeters verification sealed radioactive sources elaborated with this aim at the Radionuclide Metrology Department of the Isotope Centre of Cuba. Taking into account the international experience in this field was defined 3 -10 MBq as convenient activity range, the 137 Cs as a suitable radionuclide, and a classification ISO/99/C22212 (ISO 2919:1999) for the sealed sources to be obtained. In designed and produced models the activity is bonded in a hydrogel copolymer obtained by gamma irradiation, in a 60 Co irradiator, of a mixture of a 137 Cs aqueous solution with an approximate activity of 5 MBq with two proper monomers (acrylamide and methacrylic acid). The density of obtained copolymer is similar to that of the radioactive solutions employed in nuclear medicine departments for diagnosis and therapy. The obtained sources have appropriate physical stability for a temperature range between 40 o C below zero and 80 o C, as well as for defined activity range. The stability of the

  2. Multiplicity distribution and forward-backward correlations in the hydrodynamic theory of multiple production

    Tarasov, Yu.A.

    1992-01-01

    A hydrodynamic model for the collisions of gluon clusters is used to calculate the charge-particle multiplicity distributions in collisions of nucleons at ISR and collider energies. The separation temperature of the hydrodynamic system is calculated as a function of the rapidity [T k (γ 1 )] for each value of the inelasticity coefficient K. In the central region, this temperature is higher at collider energies than at the ISR energy. The average number of resonance clusters which decay into various (fixed) numbers of charged hadrons is found for each value of K. The number of these clusters fluctuates in accordance with a Poisson distribution. A hadron multiplicity distribution which incorporates these fluctuations is found. This distribution is averaged over the inelasticity coefficient. The distributions p(n ch ) and the KNO functions Ψ(z) are calculated for the overall and central regions of the rapidity, |y| ≤ 1.5. The broadening of the distributions and the violation of KNO scaling at collider energies results from increased contributions from the decays of resonances. The front-back multiplicity correlations are also studied; the decay of resonances is taken into account. The distributions and slope coefficients of the correlation function which are found for the various energies agree with experimental data

  3. Carbon Sources Influence Fumonisin Production in Fusarium proliferatum.

    Li, Taotao; Gong, Liang; Jiang, Guoxiang; Wang, Yong; Gupta, Vijai Kumar; Qu, Hongxia; Duan, Xuewu; Wang, Jiasheng; Jiang, Yueming

    2017-10-01

    Fusarium proliferatum is a worldwide fungal pathogen that produces fumonisins which are harmful to animal and human health. However, environmental factors affecting fumonisin biosynthesis in F. proliferatum are not well understood. Based on our preliminary results, in this study, we investigated the effect of sucrose or mannose as the sole carbon source on fumonisin B (FB) production by F. proliferatum and studied their underlying mechanisms via proteome and gene expression analysis. Our results showed that mannose, used as the sole carbon source, significantly blocked fumonisin B 1 and B 2 production by F. proliferatum as compared with the use of sucrose. Fifty-seven differentially expressed proteins were successfully identified. The downregulated proteins in the mannose-cultured strain were mainly involved in carbon metabolism, response to stress, and methionine metabolism, as compared with the sucrose-cultured strain. Moreover, quantitative real-time PCR analysis indicated that expression of several key genes involved in FB biosynthetic pathway and in transcription regulation were significantly downregulated in the mannose-cultured F. proliferatum, whereas expression of histone deacetylation-related genes were significantly upregulated. These results suggested that the blockage of FB biosynthesis by mannose was associated with the decreases in conversion of acetyl-CoA to polyketide, methionine biosynthesis, and NADPH regeneration. More importantly, milder oxidative stress, downregulated expression of genes involved in biosynthetic pathway and transcription regulation, and upregulated expression of genes with histone deacetylation possibly were responsible for the blockage of FB biosynthesis in F. proliferatum. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  4. The Phebus Fission Product and Source Term International Programmes

    Clement, B.; Zeyen, R.

    2005-01-01

    The international Phebus FP programme, initiated in 1988 is one of the major research programmes on light water reactors severe accidents. After a short description of the facility and of the test matrix, the main outcomes and results of the first four integral tests are provided and analysed. Several results were unexpected and some are of importance for safety analyses, particularly concerning fuel degradation, cladding oxidation, chemical form of some fission products, especially iodine, effect of control rod materials on degradation and chemistry, iodine behaviour in the containment. Prediction capabilities of calculation tools have largely been improved as a result of this research effort. However, significant uncertainties remain for a number of phenomena, requiring detailed physical analysis and implementation of improved models in codes, sustained by a number of separate-effect experiments. This is the subject of the new Source Term programme for a better understanding of the phenomenology on important safety issues, in accordance with priorities defined in the EURSAFE project of the 5 th European framework programme aiming at reducing the uncertainties on Source Term analyses. It covers iodine chemistry, impact of boron carbide control rods degradation and oxidation, air ingress situations and fission product release from fuel. Regarding the interpretation of Phebus, an international co-operation has been established since over ten years, particularly helpful for the improvement and common understanding of severe accident phenomena. Few months ago, the Phebus community was happy to welcome representatives of a large number of organisations from the following new European countries: the Czech republic, Hungary, Lithuania, Slovakia, Slovenia and also from Bulgaria and Romania. (author)

  5. Productivity of a nuclear chemical reactor with gamma radioisotopic sources

    Anguis T, C.

    1975-01-01

    According to an established mathematical model of successive Compton interaction processes the made calculations for major distances are extended checking the acceptability of the spheric geometry model for the experimental data for radioisotopic sources of Co-60 and Cs-137. Parameters such as the increasing factor and the absorbed dose served as comparative base. calculations for the case of a punctual source succession inside a determined volume cylinder are made to obtain the total dose, the deposited energy by each photons energetic group and the total absorbed energy inside the reactor. Varying adequately the height/radius relation for different cylinders, the distinct energy depositions are compared in each one of them once a time standardized toward a standard value of energy emitted by the reactor volume. A relation between the quantity of deposited energy in each point of the reactor and the conversion values of chemical species is established. They are induced by electromagnetic radiation and that are reported as ''G'' in the scientific literature (number of molecules formed or disappeared by each 100 e.v. of energy). Once obtained the molecular performance inside the reactor for each type of geometry, it is optimized the height/radius relation according to the maximum production of molecules by unity of time. It is completed a bibliographical review of ''G'' values reported by different types of aqueous solutions with the purpose to determine the maximum performance of molecular hydrogen as a function of pH of the solution and of the used type of solute among other factors. Calculations for the ethyl bromide production as an example of one of the industrial processes which actually work using the gamma radiation as reactions inductor are realized. (Author)

  6. Polyhydroxybutyrate production from marine source and its application.

    Kavitha, Ganapathy; Rengasamy, Ramasamy; Inbakandan, Dhinakarasamy

    2018-05-01

    The increasing significance of non-degradable plastic wastes is an emerging concern. As a substitute, researches are being endeavoured from existing reserve to yield bioplastics based on their properties of biodegradability. Owing to their cost, now the experts are quest for a substitute source like bacteria, microalgae, actinomycetes, cyanobacteria and plants. PHB is biodegradable, environmental friendly and biocompatible thermoplastics. Varying in toughness and flexibility, depending on their formulation, they are used in various ways similar to many non-biodegradable petrochemical plastics currently in use. Promising strategies contain genetic engineering of microorganisms to introduce production pathways examined for the past two decades. Such kind of researches focusing on the use of unconventional substrates, novel extraction methods, and genetically enhanced species with assessment to make PHB from marine microbes are commercially attractive field. Hence, this biopolymer synthesis may displayed as one of the survival mechanisms of endosymbiotic, macroalgae, or sponge-associated bacteria, which exist in a highly competitive and stressful marine microenvironment. This review throws light on the promising and growing awareness of using marine microbes as PHB source, along with their applications in different fields of aquaculture, medicine, antifouling and tissue engineering. Copyright © 2018 Elsevier B.V. All rights reserved.

  7. The use of coded PCR primers enables high-throughput sequencing of multiple homolog amplification products by 454 parallel sequencing.

    Jonas Binladen

    2007-02-01

    Full Text Available The invention of the Genome Sequence 20 DNA Sequencing System (454 parallel sequencing platform has enabled the rapid and high-volume production of sequence data. Until now, however, individual emulsion PCR (emPCR reactions and subsequent sequencing runs have been unable to combine template DNA from multiple individuals, as homologous sequences cannot be subsequently assigned to their original sources.We use conventional PCR with 5'-nucleotide tagged primers to generate homologous DNA amplification products from multiple specimens, followed by sequencing through the high-throughput Genome Sequence 20 DNA Sequencing System (GS20, Roche/454 Life Sciences. Each DNA sequence is subsequently traced back to its individual source through 5'tag-analysis.We demonstrate that this new approach enables the assignment of virtually all the generated DNA sequences to the correct source once sequencing anomalies are accounted for (miss-assignment rate<0.4%. Therefore, the method enables accurate sequencing and assignment of homologous DNA sequences from multiple sources in single high-throughput GS20 run. We observe a bias in the distribution of the differently tagged primers that is dependent on the 5' nucleotide of the tag. In particular, primers 5' labelled with a cytosine are heavily overrepresented among the final sequences, while those 5' labelled with a thymine are strongly underrepresented. A weaker bias also exists with regards to the distribution of the sequences as sorted by the second nucleotide of the dinucleotide tags. As the results are based on a single GS20 run, the general applicability of the approach requires confirmation. However, our experiments demonstrate that 5'primer tagging is a useful method in which the sequencing power of the GS20 can be applied to PCR-based assays of multiple homologous PCR products. The new approach will be of value to a broad range of research areas, such as those of comparative genomics, complete mitochondrial

  8. The role of envelope shape in the localization of multiple sound sources and echoes in the barn owl.

    Baxter, Caitlin S; Nelson, Brian S; Takahashi, Terry T

    2013-02-01

    Echoes and sounds of independent origin often obscure sounds of interest, but echoes can go undetected under natural listening conditions, a perception called the precedence effect. How does the auditory system distinguish between echoes and independent sources? To investigate, we presented two broadband noises to barn owls (Tyto alba) while varying the similarity of the sounds' envelopes. The carriers of the noises were identical except for a 2- or 3-ms delay. Their onsets and offsets were also synchronized. In owls, sound localization is guided by neural activity on a topographic map of auditory space. When there are two sources concomitantly emitting sounds with overlapping amplitude spectra, space map neurons discharge when the stimulus in their receptive field is louder than the one outside it and when the averaged amplitudes of both sounds are rising. A model incorporating these features calculated the strengths of the two sources' representations on the map (B. S. Nelson and T. T. Takahashi; Neuron 67: 643-655, 2010). The target localized by the owls could be predicted from the model's output. The model also explained why the echo is not localized at short delays: when envelopes are similar, peaks in the leading sound mask corresponding peaks in the echo, weakening the echo's space map representation. When the envelopes are dissimilar, there are few or no corresponding peaks, and the owl localizes whichever source is predicted by the model to be less masked. Thus the precedence effect in the owl is a by-product of a mechanism for representing multiple sound sources on its map.

  9. ANEMOS: A computer code to estimate air concentrations and ground deposition rates for atmospheric nuclides emitted from multiple operating sources

    Miller, C.W.; Sjoreen, A.L.; Begovich, C.L.; Hermann, O.W.

    1986-11-01

    This code estimates concentrations in air and ground deposition rates for Atmospheric Nuclides Emitted from Multiple Operating Sources. ANEMOS is one component of an integrated Computerized Radiological Risk Investigation System (CRRIS) developed for the US Environmental Protection Agency (EPA) for use in performing radiological assessments and in developing radiation standards. The concentrations and deposition rates calculated by ANEMOS are used in subsequent portions of the CRRIS for estimating doses and risks to man. The calculations made in ANEMOS are based on the use of a straight-line Gaussian plume atmospheric dispersion model with both dry and wet deposition parameter options. The code will accommodate a ground-level or elevated point and area source or windblown source. Adjustments may be made during the calculations for surface roughness, building wake effects, terrain height, wind speed at the height of release, the variation in plume rise as a function of downwind distance, and the in-growth and decay of daughter products in the plume as it travels downwind. ANEMOS can also accommodate multiple particle sizes and clearance classes, and it may be used to calculate the dose from a finite plume of gamma-ray-emitting radionuclides passing overhead. The output of this code is presented for 16 sectors of a circular grid. ANEMOS can calculate both the sector-average concentrations and deposition rates at a given set of downwind distances in each sector and the average of these quantities over an area within each sector bounded by two successive downwind distances. ANEMOS is designed to be used primarily for continuous, long-term radionuclide releases. This report describes the models used in the code, their computer implementation, the uncertainty associated with their use, and the use of ANEMOS in conjunction with other codes in the CRRIS. A listing of the code is included in Appendix C

  10. ANEMOS: A computer code to estimate air concentrations and ground deposition rates for atmospheric nuclides emitted from multiple operating sources

    Miller, C.W.; Sjoreen, A.L.; Begovich, C.L.; Hermann, O.W.

    1986-11-01

    This code estimates concentrations in air and ground deposition rates for Atmospheric Nuclides Emitted from Multiple Operating Sources. ANEMOS is one component of an integrated Computerized Radiological Risk Investigation System (CRRIS) developed for the US Environmental Protection Agency (EPA) for use in performing radiological assessments and in developing radiation standards. The concentrations and deposition rates calculated by ANEMOS are used in subsequent portions of the CRRIS for estimating doses and risks to man. The calculations made in ANEMOS are based on the use of a straight-line Gaussian plume atmospheric dispersion model with both dry and wet deposition parameter options. The code will accommodate a ground-level or elevated point and area source or windblown source. Adjustments may be made during the calculations for surface roughness, building wake effects, terrain height, wind speed at the height of release, the variation in plume rise as a function of downwind distance, and the in-growth and decay of daughter products in the plume as it travels downwind. ANEMOS can also accommodate multiple particle sizes and clearance classes, and it may be used to calculate the dose from a finite plume of gamma-ray-emitting radionuclides passing overhead. The output of this code is presented for 16 sectors of a circular grid. ANEMOS can calculate both the sector-average concentrations and deposition rates at a given set of downwind distances in each sector and the average of these quantities over an area within each sector bounded by two successive downwind distances. ANEMOS is designed to be used primarily for continuous, long-term radionuclide releases. This report describes the models used in the code, their computer implementation, the uncertainty associated with their use, and the use of ANEMOS in conjunction with other codes in the CRRIS. A listing of the code is included in Appendix C.

  11. Projecting southern timber supply for multiple products by subregion

    Robert C. Abt; Frederick W. Cubbage; Karen L. Abt

    2009-01-01

    While timber supply modeling has been of importance in the wood-producing regions of the United States for decades, it is only more recently that the technology and data have allowed disaggregation of supply and demand to substate regions, including product specific breakdowns and endogenous land use and plantation changes. Using southwide data and an economic supply...

  12. The Protein Identifier Cross-Referencing (PICR service: reconciling protein identifiers across multiple source databases

    Leinonen Rasko

    2007-10-01

    Full Text Available Abstract Background Each major protein database uses its own conventions when assigning protein identifiers. Resolving the various, potentially unstable, identifiers that refer to identical proteins is a major challenge. This is a common problem when attempting to unify datasets that have been annotated with proteins from multiple data sources or querying data providers with one flavour of protein identifiers when the source database uses another. Partial solutions for protein identifier mapping exist but they are limited to specific species or techniques and to a very small number of databases. As a result, we have not found a solution that is generic enough and broad enough in mapping scope to suit our needs. Results We have created the Protein Identifier Cross-Reference (PICR service, a web application that provides interactive and programmatic (SOAP and REST access to a mapping algorithm that uses the UniProt Archive (UniParc as a data warehouse to offer protein cross-references based on 100% sequence identity to proteins from over 70 distinct source databases loaded into UniParc. Mappings can be limited by source database, taxonomic ID and activity status in the source database. Users can copy/paste or upload files containing protein identifiers or sequences in FASTA format to obtain mappings using the interactive interface. Search results can be viewed in simple or detailed HTML tables or downloaded as comma-separated values (CSV or Microsoft Excel (XLS files suitable for use in a local database or a spreadsheet. Alternatively, a SOAP interface is available to integrate PICR functionality in other applications, as is a lightweight REST interface. Conclusion We offer a publicly available service that can interactively map protein identifiers and protein sequences to the majority of commonly used protein databases. Programmatic access is available through a standards-compliant SOAP interface or a lightweight REST interface. The PICR

  13. Multiple-collision model for pion production in relativistic nucleus-nucleus collisions

    Vary, J.P.

    1978-01-01

    A simple model for pion production in relativistic heavy-ion collisions is developed based on nucleon-nucleon data, nuclear density distribution, and the assumption of straight-line trajectories. Multiplicity distributions for total pion production and for negative-pion production are predicted for 40 Ar incident on a Pb 3 O 4 target at 1.8 GeV/nucleon. Production through intermediate baryon resonances reduces the high-multiplicity region but insufficiently to yield agreement with data. This implies the need for a coherent production mechanism

  14. Ion beam production and study of radioactive isotopes with the laser ion source at ISOLDE

    Fedosseev, Valentin; Chrysalidis, Katerina; Day Goodacre, Thomas; Marsh, Bruce; Rothe, Sebastian; Seiffert, Christoph; Wendt, Klaus

    2017-08-01

    At ISOLDE the majority of radioactive ion beams are produced using the resonance ionization laser ion source (RILIS). This ion source is based on resonant excitation of atomic transitions by wavelength tunable laser radiation. Since its installation at the ISOLDE facility in 1994, the RILIS laser setup has been developed into a versatile remotely operated laser system comprising state-of-the-art solid state and dye lasers capable of generating multiple high quality laser beams at any wavelength in the range of 210-950 nm. A continuous programme of atomic ionization scheme development at CERN and at other laboratories has gradually increased the number of RILIS-ionized elements. At present, isotopes of 40 different elements have been selectively laser-ionized by the ISOLDE RILIS. Studies related to the optimization of the laser-atom interaction environment have yielded new laser ion source types: the laser ion source and trap and the versatile arc discharge and laser ion source. Depending on the specific experimental requirements for beam purity or versatility to switch between different ionization mechanisms, these may offer a favourable alternative to the standard hot metal cavity configuration. In addition to its main purpose of ion beam production, the RILIS is used for laser spectroscopy of radioisotopes. In an ongoing experimental campaign the isotope shifts and hyperfine structure of long isotopic chains have been measured by the extremely sensitive in-source laser spectroscopy method. The studies performed in the lead region were focused on nuclear deformation and shape coexistence effects around the closed proton shell Z = 82. The paper describes the functional principles of the RILIS, the current status of the laser system and demonstrated capabilities for the production of different ion beams including the high-resolution studies of short-lived isotopes and other applications of RILIS lasers for ISOLDE experiments. This article belongs to the Focus on

  15. Sources of product information used by consumers when purchasing kitchen cabinets.

    Geoffrey H. Donovan; David L. Nicholls; Joseph. Roos

    2004-01-01

    Survey data from home shows in Seattle, Washington and Anchorage, Alaska were used to determine the sources of product information used by consumers when buying kitchen cabinets. Results show that in-store sales staff are the most common source of product information, and that consumers' favorite wood species, age, and gender can influence the source of product...

  16. The test beamline of the European Spallation Source – Instrumentation development and wavelength frame multiplication

    Woracek, R.; Hofmann, T.; Bulat, M.; Sales, M.; Habicht, K.; Andersen, K.; Strobl, M.

    2016-01-01

    The European Spallation Source (ESS), scheduled to start operation in 2020, is aiming to deliver the most intense neutron beams for experimental research of any facility worldwide. Its long pulse time structure implies significant differences for instrumentation compared to other spallation sources which, in contrast, are all providing short neutron pulses. In order to enable the development of methods and technology adapted to this novel type of source well in advance of the first instruments being constructed at ESS, a test beamline (TBL) was designed and built at the BER II research reactor at Helmholtz-Zentrum Berlin (HZB). Operating the TBL shall provide valuable experience in order to allow for a smooth start of operations at ESS. The beamline is capable of mimicking the ESS pulse structure by a double chopper system and provides variable wavelength resolution as low as 0.5% over a wide wavelength band between 1.6 Å and 10 Å by a dedicated wavelength frame multiplication (WFM) chopper system. WFM is proposed for several ESS instruments to allow for flexible time-of-flight resolution. Hence, ESS will benefit from the TBL which offers unique possibilities for testing methods and components. This article describes the main capabilities of the instrument, its performance as experimentally verified during the commissioning, and its relevance to currently starting ESS instrumentation projects.

  17. Misconceptions and biases in German students' perception of multiple energy sources: implications for science education

    Lee, Roh Pin

    2016-04-01

    Misconceptions and biases in energy perception could influence people's support for developments integral to the success of restructuring a nation's energy system. Science education, in equipping young adults with the cognitive skills and knowledge necessary to navigate in the confusing energy environment, could play a key role in paving the way for informed decision-making. This study examined German students' knowledge of the contribution of diverse energy sources to their nation's energy mix as well as their affective energy responses so as to identify implications for science education. Specifically, the study investigated whether and to what extent students hold mistaken beliefs about the role of multiple energy sources in their nation's energy mix, and assessed how misconceptions could act as self-generated reference points to underpin support/resistance of proposed developments. An in-depth analysis of spontaneous affective associations with five key energy sources also enabled the identification of underlying concerns driving people's energy responses and facilitated an examination of how affective perception, in acting as a heuristic, could lead to biases in energy judgment and decision-making. Finally, subgroup analysis differentiated by education and gender supported insights into a 'two culture' effect on energy perception and the challenge it poses to science education.

  18. The test beamline of the European Spallation Source – Instrumentation development and wavelength frame multiplication

    Woracek, R., E-mail: robin.woracek@esss.se [European Spallation Source ESS ERIC, P.O. Box 176, SE-22100 Lund (Sweden); Hofmann, T.; Bulat, M. [Helmholtz-Zentrum Berlin für Materialien und Energie, Hahn-Meitner Platz 1, 14109 Berlin (Germany); Sales, M. [Technical University of Denmark, Fysikvej, 2800 Kgs. Lyngby (Denmark); Habicht, K. [Helmholtz-Zentrum Berlin für Materialien und Energie, Hahn-Meitner Platz 1, 14109 Berlin (Germany); Andersen, K. [European Spallation Source ESS ERIC, P.O. Box 176, SE-22100 Lund (Sweden); Strobl, M. [European Spallation Source ESS ERIC, P.O. Box 176, SE-22100 Lund (Sweden); Technical University of Denmark, Fysikvej, 2800 Kgs. Lyngby (Denmark)

    2016-12-11

    The European Spallation Source (ESS), scheduled to start operation in 2020, is aiming to deliver the most intense neutron beams for experimental research of any facility worldwide. Its long pulse time structure implies significant differences for instrumentation compared to other spallation sources which, in contrast, are all providing short neutron pulses. In order to enable the development of methods and technology adapted to this novel type of source well in advance of the first instruments being constructed at ESS, a test beamline (TBL) was designed and built at the BER II research reactor at Helmholtz-Zentrum Berlin (HZB). Operating the TBL shall provide valuable experience in order to allow for a smooth start of operations at ESS. The beamline is capable of mimicking the ESS pulse structure by a double chopper system and provides variable wavelength resolution as low as 0.5% over a wide wavelength band between 1.6 Å and 10 Å by a dedicated wavelength frame multiplication (WFM) chopper system. WFM is proposed for several ESS instruments to allow for flexible time-of-flight resolution. Hence, ESS will benefit from the TBL which offers unique possibilities for testing methods and components. This article describes the main capabilities of the instrument, its performance as experimentally verified during the commissioning, and its relevance to currently starting ESS instrumentation projects.

  19. Thermonuclear neutron sources - a new isotope production technology

    Heckman, Richard A [Lawrence Radiation Laboratory, University of California, Livermore, CA (United States)

    1970-05-15

    With the successful detonation of the Hutch device, we have demonstrated the feasibility of a new isotope production technique. The exposure of a 238-U and 232-Th target to an extremely large neutron flux, 1.8 x 10{sup 25} neutrons/cm{sup 2}, produced super-heavy nuclides up to 257-Fm by the multiple neutron capture process. Kilogram quantities of Hutch debris were recovered by a modification of standard drilling techniques. A semicontinuous batch process was used to concentrate approximately 10{sup 10} atoms of 257-Fm from approximately 50 kg of debris. Experience from the Hutch debris recovery efforts indicates that significant engineering advances in recovery techniques and subsequent cost reductions are possible. The demonstrated success of the device clearly justifies anengineering development program. Comparing debris recovery by underground mining operations with recovery using possible advances in drilling technology does not indicate an obvious cost advantage of one system over the other. Possible advances in mining technology could change this tentative conclusion. Any novel schemes for debris concentration that might be possible through an understanding of underground nuclear detonation phonomenology would also radically affect recovery and processing economics. A preliminary process engineering design of a large-scale (a few hundred to a few thousand kilograms) processing facility located at the Nevada Test Site will be discussed. Cost estimates for isotopes produced in this facility will be described. The effects of debris concentration, 'ore' beneficiation, and total debris processed on unit costs will be discussed. These preliminary estimates show that this new isotope 'production' scheme would be competitive with existing reactor facilities. (author)

  20. Towards Integration of CAx Systems and a Multiple-View Product Modeller in Mechanical Design

    H. Song

    2005-01-01

    Full Text Available This paper deals with the development of an integration framework and its implementation for the connexion of CAx systems and multiple-view product modelling. The integration framework is presented regarding its conceptual level and the implementation level is described currently with the connexion of a functional modeller, a multiple-view product modeller, an optimisation module and a CAD system. The integration between the multiple-view product modeller and CATIA V5 based on the STEP standard is described in detail. Finally, the presented works are discussed and future research developments are suggested. 

  1. Innovation in a multiple-stage, multiple-product food marketing chain

    Baker, Alister Derek; Christensen, Tove

    A model of a 3-stage food marketing chain is presented for the case of two products. Its extension of existing work is its capacity to examine non-competitive input and output markets in two marketing chains at once, and have them related by demand and cost interactions. The simulated impacts...... of market power in a single chain generally reproduce those delivered by previous authors. The impacts of market power in related chains are found to depend on linkages between chains in terms of interactions in consumer demand. Interactions between products in costs (economies of scope) generate...... an interesting result in that a possible market failure is identified that may be offset by the exercise of market power. The generation of farm-level innovation is seen to be largely unaffected by market power, but where market power is exercised the benefits are extracted from farmers and consumers...

  2. Docosahexaenoic Acid Reduces Amyloid β Production via Multiple Pleiotropic Mechanisms*

    Grimm, Marcus O. W.; Kuchenbecker, Johanna; Grösgen, Sven; Burg, Verena K.; Hundsdörfer, Benjamin; Rothhaar, Tatjana L.; Friess, Petra; de Wilde, Martijn C.; Broersen, Laus M.; Penke, Botond; Péter, Mária; Vígh, László; Grimm, Heike S.; Hartmann, Tobias

    2011-01-01

    Alzheimer disease is characterized by accumulation of the β-amyloid peptide (Aβ) generated by β- and γ-secretase processing of the amyloid precursor protein (APP). The intake of the polyunsaturated fatty acid docosahexaenoic acid (DHA) has been associated with decreased amyloid deposition and a reduced risk in Alzheimer disease in several epidemiological trials; however, the exact underlying molecular mechanism remains to be elucidated. Here, we systematically investigate the effect of DHA on amyloidogenic and nonamyloidogenic APP processing and the potential cross-links to cholesterol metabolism in vivo and in vitro. DHA reduces amyloidogenic processing by decreasing β- and γ-secretase activity, whereas the expression and protein levels of BACE1 and presenilin1 remain unchanged. In addition, DHA increases protein stability of α-secretase resulting in increased nonamyloidogenic processing. Besides the known effect of DHA to decrease cholesterol de novo synthesis, we found cholesterol distribution in plasma membrane to be altered. In the presence of DHA, cholesterol shifts from raft to non-raft domains, and this is accompanied by a shift in γ-secretase activity and presenilin1 protein levels. Taken together, DHA directs amyloidogenic processing of APP toward nonamyloidogenic processing, effectively reducing Aβ release. DHA has a typical pleiotropic effect; DHA-mediated Aβ reduction is not the consequence of a single major mechanism but is the result of combined multiple effects. PMID:21324907

  3. Prokaryotic Heme Biosynthesis: Multiple Pathways to a Common Essential Product.

    Dailey, Harry A; Dailey, Tamara A; Gerdes, Svetlana; Jahn, Dieter; Jahn, Martina; O'Brian, Mark R; Warren, Martin J

    2017-03-01

    The advent of heme during evolution allowed organisms possessing this compound to safely and efficiently carry out a variety of chemical reactions that otherwise were difficult or impossible. While it was long assumed that a single heme biosynthetic pathway existed in nature, over the past decade, it has become clear that there are three distinct pathways among prokaryotes, although all three pathways utilize a common initial core of three enzymes to produce the intermediate uroporphyrinogen III. The most ancient pathway and the only one found in the Archaea converts siroheme to protoheme via an oxygen-independent four-enzyme-step process. Bacteria utilize the initial core pathway but then add one additional common step to produce coproporphyrinogen III. Following this step, Gram-positive organisms oxidize coproporphyrinogen III to coproporphyrin III, insert iron to make coproheme, and finally decarboxylate coproheme to protoheme, whereas Gram-negative bacteria first decarboxylate coproporphyrinogen III to protoporphyrinogen IX and then oxidize this to protoporphyrin IX prior to metal insertion to make protoheme. In order to adapt to oxygen-deficient conditions, two steps in the bacterial pathways have multiple forms to accommodate oxidative reactions in an anaerobic environment. The regulation of these pathways reflects the diversity of bacterial metabolism. This diversity, along with the late recognition that three pathways exist, has significantly slowed advances in this field such that no single organism's heme synthesis pathway regulation is currently completely characterized. Copyright © 2017 American Society for Microbiology.

  4. All-source Information Management and Integration for Improved Collective Intelligence Production

    2011-06-01

    Intelligence (ELINT) • Open Source Intelligence ( OSINT ) • Technical Intelligence (TECHINT) These intelligence disciplines produce... intelligence , measurement and signature intelligence , signals intelligence , and open - source data, in the production of intelligence . All- source intelligence ...All- Source Information Integration and Management) R&D Project 3 All- Source Intelligence

  5. Modeling the Potential Effects of New Tobacco Products and Policies: A Dynamic Population Model for Multiple Product Use and Harm

    Vugrin, Eric D.; Rostron, Brian L.; Verzi, Stephen J.; Brodsky, Nancy S.; Brown, Theresa J.; Choiniere, Conrad J.; Coleman, Blair N.; Paredes, Antonio; Apelberg, Benjamin J.

    2015-01-01

    Background Recent declines in US cigarette smoking prevalence have coincided with increases in use of other tobacco products. Multiple product tobacco models can help assess the population health impacts associated with use of a wide range of tobacco products. Methods and Findings We present a multi-state, dynamical systems population structure model that can be used to assess the effects of tobacco product use behaviors on population health. The model incorporates transition behaviors, such as initiation, cessation, switching, and dual use, related to the use of multiple products. The model tracks product use prevalence and mortality attributable to tobacco use for the overall population and by sex and age group. The model can also be used to estimate differences in these outcomes between scenarios by varying input parameter values. We demonstrate model capabilities by projecting future cigarette smoking prevalence and smoking-attributable mortality and then simulating the effects of introduction of a hypothetical new lower-risk tobacco product under a variety of assumptions about product use. Sensitivity analyses were conducted to examine the range of population impacts that could occur due to differences in input values for product use and risk. We demonstrate that potential benefits from cigarette smokers switching to the lower-risk product can be offset over time through increased initiation of this product. Model results show that population health benefits are particularly sensitive to product risks and initiation, switching, and dual use behaviors. Conclusion Our model incorporates the variety of tobacco use behaviors and risks that occur with multiple products. As such, it can evaluate the population health impacts associated with the introduction of new tobacco products or policies that may result in product switching or dual use. Further model development will include refinement of data inputs for non-cigarette tobacco products and inclusion of health

  6. A multiple objective magnet sorting algorithm for the Advanced Light Source insertion devices

    Humphries, D.; Goetz, F.; Kownacki, P.; Marks, S.; Schlueter, R.

    1995-01-01

    Insertion devices for the Advanced Light Source (ALS) incorporate large numbers of permanent magnets which have a variety of magnetization orientation errors. These orientation errors can produce field errors which affect both the spectral brightness of the insertion devices and the storage ring electron beam dynamics. A perturbation study was carried out to quantify the effects of orientation errors acting in a hybrid magnetic structure. The results of this study were used to develop a multiple stage sorting algorithm which minimizes undesirable integrated field errors and essentially eliminates pole excitation errors. When applied to a measured magnet population for an existing insertion device, an order of magnitude reduction in integrated field errors was achieved while maintaining near zero pole excitation errors

  7. Use of multiple water surface flow constructed wetlands for non-point source water pollution control.

    Li, Dan; Zheng, Binghui; Liu, Yan; Chu, Zhaosheng; He, Yan; Huang, Minsheng

    2018-05-02

    Multiple free water surface flow constructed wetlands (multi-FWS CWs) are a variety of conventional water treatment plants for the interception of pollutants. This review encapsulated the characteristics and applications in the field of ecological non-point source water pollution control technology. The roles of in-series design and operation parameters (hydraulic residence time, hydraulic load rate, water depth and aspect ratio, composition of influent, and plant species) for performance intensification were also analyzed, which were crucial to achieve sustainable and effective contaminants removal, especially the retention of nutrient. The mechanism study of design and operation parameters for the removal of nitrogen and phosphorus was also highlighted. Conducive perspectives for further research on optimizing its design/operation parameters and advanced technologies of ecological restoration were illustrated to possibly interpret the functions of multi-FWS CWs.

  8. The test beamline of the European Spallation Source - Instrumentation development and wavelength frame multiplication

    Woracek, R.; Hofmann, T.; Bulat, M.

    2016-01-01

    which, in contrast, are all providing short neutron pulses. In order to enable the development of methods and technology adapted to this novel type of source well in advance of the first instruments being constructed at ESS, a test beamline (TBL) was designed and built at the BER II research reactor...... wavelength band between 1.6 A and 10 A by a dedicated wavelength frame multiplication (WFM) chopper system. WFM is proposed for several ESS instruments to allow for flexible time-of-flight resolution. Hence, ESS will benefit from the TBL which offers unique possibilities for testing methods and components....... This article describes the main capabilities of the instrument, its performance as experimentally verified during the commissioning, and its relevance to currently starting ESS instrumentation projects....

  9. Multiple Sources of Pressure for Change: The Barroso Commission and Energy Policy for an Enlarged EU

    Jan Frederik Braun

    2009-11-01

    Full Text Available This article presents a preliminary analysis of how and why the role, work and status of the European Commission are changing in an enlarged European Union. It does so by focusing on multiple sources of pressure for change. These include: enlargement, new modes of governance, administrative reforms and changed leadership under Barroso. Combined, though not interlinked, these multiple sources of pressure are evidence of the increasing difficulty for the Commission to design and propose Community-wide answers to complex challenges in a more diverse Union. For this reason, the Commission under Barroso relies less on its traditional monopoly power to propose formal legislation and more on non-traditional modes of policy-making. Energy policy, especially its external dimension, constitutes a policy field that has been affected by enlargement, i.e. characterised by an increasing heterogeneity of needs and preferences among the member states. Not only does it resists Community-wide answers, it also allows the Commission, as an agent, to make use of bureaucratic drifts, i.e. exploit its strategic position in the EU’s governance system and use of a range of formal and informal resources of expertise. To deliver sustainable European added value to this complex policy area, however, the Commission must focus more on pragmatic policy results by making smart use of the EU’s increasing asymmetry, diversity and subsidiarity in a bottom-up approach. A non-legislative approach can serve as a modus vivendi to keep the momentum going in the Union’s difficult struggle to establish a workable energy regime.

  10. Associated multiplicity of γ-particles in processes of lepton pair production on nuclei

    Gevorkyan, S.R.; Gulkanyan, H.R.; Vartanyan, V.A.

    1986-01-01

    An expression has been obtained for mean multiplicity of g-particles accompanying the process of deep-inelastic lepton pair production on nuclei. The expression allows one to get information on structure peculiarities of leading hadron in this process

  11. The Use of Source-Related Strategies in Evaluating Multiple Psychology Texts: A Student-Scientist Comparison

    von der Mühlen, Sarah; Richter, Tobias; Schmid, Sebastian; Schmidt, Elisabeth Marie; Berthold, Kirsten

    2016-01-01

    Multiple text comprehension can greatly benefit from paying attention to sources and from using this information for evaluating text information. Previous research based on texts from the domain of history suggests that source-related strategies are acquired as part of the discipline expertise as opposed to the spontaneous use of these strategies…

  12. Tracing waste to the source along the product life cycle

    Maina, S.M.

    2008-01-01

    It is currently evident that the environment is ailing. We are exposed to many human activities that are devastating to the environment and societies. Since the time the report, Our Common Future, from the UN World Commission on environment and Development (WCED) identified the problem in 1987, its effects are currently a reality. The report sought to recapture the spirit of the United Nations Conference on the Human environment. It placed environmental issues firmly on the political agenda. It also aimed to discuss the environment and development as a single issue. In it is advanced the view that, many countries with poor environmental governance systems are likely to have have conflicts and poor laws protecting the environment. This paper looks at this problem from an ethical perspective. Effects of lack of eco-ethics are numerous. Burning refuse affecting air quality, lack of space for dumping solid waste, the increasing cost of waste disposal and hazards to ground water. In Kenya, the situation of solid waste is a source of concern. In this paper a view is advanced that the problem starts with the product designer. In Kenya designers use flawed design process ignoring the ethical responsibility towards environment, leading to waste accumulation around Nairobi. The uncollected or illegally dumped wastes constitute a disaster for human health and causes environmental degradation (author)

  13. Ozone production at the National Synchrotron Light Source

    Weilandics, C.; Rohrig, N.; Gmur, N.F.

    1987-01-01

    Ozone production by synchrotron radiation as a function of power density in air was investigated using a white beam at the BNL National Synchrotron Light Source (NSLS) x-ray ring. Power densities were calculated from the energy spectrum at 2.52 GeV. Ozone concentrations in small beam pipes were measured for power densities between I = 10 12 and 10 15 eV . cm -3 . sec -1 . The measured ozone half-life was 37 +- 2 min. The measured G-value was 2.69 +- 0.14 mol/100 eV and the ozone destruction factor k was less than 7 x 10 -19 cm 3 . eV -1 . The random uncertainties stated are approximately one standard error. The large departure of the values for G and k from previous values suggest that some undiscovered systematic error may exist in the experiment. Ozone concentration in excess of the 0.1 ppM ACGIH TLV can be generated in the experimental hutches but can readily be controlled. Industrial hygiene aspects of operation and possible control measures will be discussed. 19 refs., 7 figs., 3 tabs

  14. Pediocins: The bacteriocins of Pediococci. Sources, production, properties and applications

    Anastasiadou Sofia

    2009-01-01

    Full Text Available Abstract Class IIa bacteriocins from lactic acid bacteria are small, cationic proteins with antilisterial activity. Within this class, the pediocins are those bacteriocins that share a highly conserved hydrophilic and charged N-terminal part harboring the consensus sequence -YGNGV- and a more variable hydrophobic and/or amphiphilic C-terminal part. Several pediocins have been isolated and characterized. Despite the structural similarities, their molecular weight varies, as well as their spectrum of antimicrobial activity. They exhibit important technological properties, e.g. thermostability and retaining of activity at a wide pH range, which along with the bactericidal action against Gram-positive food spoilage and pathogenic bacteria, make them an important class of biopreservatives. Much new information regarding the pediocins has emerged during the last years. In this review, we summarize and discuss all the available information regarding the sources of pediocins, the characteristics of their biosynthesis and production in fermentation systems, the characteristics of the known pediocin molecules, and their antibacterial action. The advances made by genetic engineering in improving the features of pediocins are also discussed, as well as their perspectives for future applications.

  15. Optimal planning of multiple distributed generation sources in distribution networks: A new approach

    AlRashidi, M.R., E-mail: malrash2002@yahoo.com [Department of Electrical Engineering, College of Technological Studies, Public Authority for Applied Education and Training (PAAET) (Kuwait); AlHajri, M.F., E-mail: mfalhajri@yahoo.com [Department of Electrical Engineering, College of Technological Studies, Public Authority for Applied Education and Training (PAAET) (Kuwait)

    2011-10-15

    Highlights: {yields} A new hybrid PSO for optimal DGs placement and sizing. {yields} Statistical analysis to fine tune PSO parameters. {yields} Novel constraint handling mechanism to handle different constraints types. - Abstract: An improved particle swarm optimization algorithm (PSO) is presented for optimal planning of multiple distributed generation sources (DG). This problem can be divided into two sub-problems: the DG optimal size (continuous optimization) and location (discrete optimization) to minimize real power losses. The proposed approach addresses the two sub-problems simultaneously using an enhanced PSO algorithm capable of handling multiple DG planning in a single run. A design of experiment is used to fine tune the proposed approach via proper analysis of PSO parameters interaction. The proposed algorithm treats the problem constraints differently by adopting a radial power flow algorithm to satisfy the equality constraints, i.e. power flows in distribution networks, while the inequality constraints are handled by making use of some of the PSO features. The proposed algorithm was tested on the practical 69-bus power distribution system. Different test cases were considered to validate the proposed approach consistency in detecting optimal or near optimal solution. Results are compared with those of Sequential Quadratic Programming.

  16. Optimal planning of multiple distributed generation sources in distribution networks: A new approach

    AlRashidi, M.R.; AlHajri, M.F.

    2011-01-01

    Highlights: → A new hybrid PSO for optimal DGs placement and sizing. → Statistical analysis to fine tune PSO parameters. → Novel constraint handling mechanism to handle different constraints types. - Abstract: An improved particle swarm optimization algorithm (PSO) is presented for optimal planning of multiple distributed generation sources (DG). This problem can be divided into two sub-problems: the DG optimal size (continuous optimization) and location (discrete optimization) to minimize real power losses. The proposed approach addresses the two sub-problems simultaneously using an enhanced PSO algorithm capable of handling multiple DG planning in a single run. A design of experiment is used to fine tune the proposed approach via proper analysis of PSO parameters interaction. The proposed algorithm treats the problem constraints differently by adopting a radial power flow algorithm to satisfy the equality constraints, i.e. power flows in distribution networks, while the inequality constraints are handled by making use of some of the PSO features. The proposed algorithm was tested on the practical 69-bus power distribution system. Different test cases were considered to validate the proposed approach consistency in detecting optimal or near optimal solution. Results are compared with those of Sequential Quadratic Programming.

  17. Multiple Signal Classification Algorithm Based Electric Dipole Source Localization Method in an Underwater Environment

    Yidong Xu

    2017-10-01

    Full Text Available A novel localization method based on multiple signal classification (MUSIC algorithm is proposed for positioning an electric dipole source in a confined underwater environment by using electric dipole-receiving antenna array. In this method, the boundary element method (BEM is introduced to analyze the boundary of the confined region by use of a matrix equation. The voltage of each dipole pair is used as spatial-temporal localization data, and it does not need to obtain the field component in each direction compared with the conventional fields based localization method, which can be easily implemented in practical engineering applications. Then, a global-multiple region-conjugate gradient (CG hybrid search method is used to reduce the computation burden and to improve the operation speed. Two localization simulation models and a physical experiment are conducted. Both the simulation results and physical experiment result provide accurate positioning performance, with the help to verify the effectiveness of the proposed localization method in underwater environments.

  18. On the multiplicative product of the Dirac-delta distribution on the hyper-surface

    Kananthai, A.

    1999-01-01

    In this paper, we give a sense to the distributional multiplicative product [Java Applet] where [Java Applet] is the Dirac-delta distribution, [Java Applet], [Java Applet], where [Java Applet] and [Java Applet] with [Java Applet] is the dimension of the Euclidean space [Java Applet], [Java Applet], [Java Applet], and [Java Applet] is a real number. On the certain conditions of [Java Applet] and [Java Applet] of such a multiplicative product, we obtain a formula related to the Green function i...

  19. Electrical source imaging of interictal spikes using multiple sparse volumetric priors for presurgical epileptogenic focus localization

    Gregor Strobbe

    2016-01-01

    Full Text Available Electrical source imaging of interictal spikes observed in EEG recordings of patients with refractory epilepsy provides useful information to localize the epileptogenic focus during the presurgical evaluation. However, the selection of the time points or time epochs of the spikes in order to estimate the origin of the activity remains a challenge. In this study, we consider a Bayesian EEG source imaging technique for distributed sources, i.e. the multiple volumetric sparse priors (MSVP approach. The approach allows to estimate the time courses of the intensity of the sources corresponding with a specific time epoch of the spike. Based on presurgical averaged interictal spikes in six patients who were successfully treated with surgery, we estimated the time courses of the source intensities for three different time epochs: (i an epoch starting 50 ms before the spike peak and ending at 50% of the spike peak during the rising phase of the spike, (ii an epoch starting 50 ms before the spike peak and ending at the spike peak and (iii an epoch containing the full spike time period starting 50 ms before the spike peak and ending 230 ms after the spike peak. To identify the primary source of the spike activity, the source with the maximum energy from 50 ms before the spike peak till 50% of the spike peak was subsequently selected for each of the time windows. For comparison, the activity at the spike peaks and at 50% of the peaks was localized using the LORETA inversion technique and an ECD approach. Both patient-specific spherical forward models and patient-specific 5-layered finite difference models were considered to evaluate the influence of the forward model. Based on the resected zones in each of the patients, extracted from post-operative MR images, we compared the distances to the resection border of the estimated activity. Using the spherical models, the distances to the resection border for the MSVP approach and each of the different time

  20. An Analysis of Open Source Security Software Products Downloads

    Barta, Brian J.

    2014-01-01

    Despite the continued demand for open source security software, a gap in the identification of success factors related to the success of open source security software persists. There are no studies that accurately assess the extent of this persistent gap, particularly with respect to the strength of the relationships of open source software…

  1. Prediction With Dimension Reduction of Multiple Molecular Data Sources for Patient Survival

    Adam Kaplan

    2017-07-01

    Full Text Available Predictive modeling from high-dimensional genomic data is often preceded by a dimension reduction step, such as principal component analysis (PCA. However, the application of PCA is not straightforward for multisource data, wherein multiple sources of ‘omics data measure different but related biological components. In this article, we use recent advances in the dimension reduction of multisource data for predictive modeling. In particular, we apply exploratory results from Joint and Individual Variation Explained (JIVE, an extension of PCA for multisource data, for prediction of differing response types. We conduct illustrative simulations to illustrate the practical advantages and interpretability of our approach. As an application example, we consider predicting survival for patients with glioblastoma multiforme from 3 data sources measuring messenger RNA expression, microRNA expression, and DNA methylation. We also introduce a method to estimate JIVE scores for new samples that were not used in the initial dimension reduction and study its theoretical properties; this method is implemented in the R package R.JIVE on CRAN, in the function jive.predict.

  2. SIGMA/B, Doses in Space Vehicle for Multiple Trajectories, Various Radiation Source

    Jordan, T.M.

    2003-01-01

    1 - Description of problem or function: SIGMA/B calculates radiation dose at arbitrary points inside a space vehicle, taking into account vehicle geometry, heterogeneous placement of equipment and stores, vehicle materials, time-weighted astronaut positions and many radiation sources from mission trajectories, e.g. geomagnetically trapped protons and electrons, solar flare particles, galactic cosmic rays and their secondary radiations. The vehicle geometry, equipment and supplies, and man models are described by quadric surfaces. The irradiating flux field may be anisotropic. The code can be used to perform simultaneous dose calculations for multiple vehicle trajectories, each involving several radiation sources. Results are presented either as dose as a function of shield thickness, or the dose received through designated outer sections of the vehicle. 2 - Method of solution: Automatic sectoring of the vehicle is performed by a Simpson's rule integration over angle; the dose is computed by a numerical angular integration of the dose attenuation kernels about the dose points. The kernels are curve-fit functions constructed from input data tables. 3 - Restrictions on the complexity of the problem: The code uses variable dimensioning techniques to store data. The only restriction on problem size is the available core storage

  3. Characterize kinematic rupture history of large earthquakes with Multiple Haskell sources

    Jia, Z.; Zhan, Z.

    2017-12-01

    Earthquakes are often regarded as continuous rupture along a single fault, but the occurrence of complex large events involving multiple faults and dynamic triggering challenges this view. Such rupture complexities cause difficulties in existing finite fault inversion algorithms, because they rely on specific parameterizations and regularizations to obtain physically meaningful solutions. Furthermore, it is difficult to assess reliability and uncertainty of obtained rupture models. Here we develop a Multi-Haskell Source (MHS) method to estimate rupture process of large earthquakes as a series of sub-events of varying location, timing and directivity. Each sub-event is characterized by a Haskell rupture model with uniform dislocation and constant unilateral rupture velocity. This flexible yet simple source parameterization allows us to constrain first-order rupture complexity of large earthquakes robustly. Additionally, relatively few parameters in the inverse problem yields improved uncertainty analysis based on Markov chain Monte Carlo sampling in a Bayesian framework. Synthetic tests and application of MHS method on real earthquakes show that our method can capture major features of large earthquake rupture process, and provide information for more detailed rupture history analysis.

  4. Development of a Monte Carlo multiple source model for inclusion in a dose calculation auditing tool.

    Faught, Austin M; Davidson, Scott E; Fontenot, Jonas; Kry, Stephen F; Etzel, Carol; Ibbott, Geoffrey S; Followill, David S

    2017-09-01

    The Imaging and Radiation Oncology Core Houston (IROC-H) (formerly the Radiological Physics Center) has reported varying levels of agreement in their anthropomorphic phantom audits. There is reason to believe one source of error in this observed disagreement is the accuracy of the dose calculation algorithms and heterogeneity corrections used. To audit this component of the radiotherapy treatment process, an independent dose calculation tool is needed. Monte Carlo multiple source models for Elekta 6 MV and 10 MV therapeutic x-ray beams were commissioned based on measurement of central axis depth dose data for a 10 × 10 cm 2 field size and dose profiles for a 40 × 40 cm 2 field size. The models were validated against open field measurements consisting of depth dose data and dose profiles for field sizes ranging from 3 × 3 cm 2 to 30 × 30 cm 2 . The models were then benchmarked against measurements in IROC-H's anthropomorphic head and neck and lung phantoms. Validation results showed 97.9% and 96.8% of depth dose data passed a ±2% Van Dyk criterion for 6 MV and 10 MV models respectively. Dose profile comparisons showed an average agreement using a ±2%/2 mm criterion of 98.0% and 99.0% for 6 MV and 10 MV models respectively. Phantom plan comparisons were evaluated using ±3%/2 mm gamma criterion, and averaged passing rates between Monte Carlo and measurements were 87.4% and 89.9% for 6 MV and 10 MV models respectively. Accurate multiple source models for Elekta 6 MV and 10 MV x-ray beams have been developed for inclusion in an independent dose calculation tool for use in clinical trial audits. © 2017 American Association of Physicists in Medicine.

  5. A Numerical Study on the Excitation of Guided Waves in Rectangular Plates Using Multiple Point Sources

    Wenbo Duan

    2017-12-01

    Full Text Available Ultrasonic guided waves are widely used to inspect and monitor the structural integrity of plates and plate-like structures, such as ship hulls and large storage-tank floors. Recently, ultrasonic guided waves have also been used to remove ice and fouling from ship hulls, wind-turbine blades and aeroplane wings. In these applications, the strength of the sound source must be high for scanning a large area, or to break the bond between ice, fouling and plate substrate. More than one transducer may be used to achieve maximum sound power output. However, multiple sources can interact with each other, and form a sound field in the structure with local constructive and destructive regions. Destructive regions are weak regions and shall be avoided. When multiple transducers are used it is important that they are arranged in a particular way so that the desired wave modes can be excited to cover the whole structure. The objective of this paper is to provide a theoretical basis for generating particular wave mode patterns in finite-width rectangular plates whose length is assumed to be infinitely long with respect to its width and thickness. The wave modes have displacements in both width and thickness directions, and are thus different from the classical Lamb-type wave modes. A two-dimensional semi-analytical finite element (SAFE method was used to study dispersion characteristics and mode shapes in the plate up to ultrasonic frequencies. The modal analysis provided information on the generation of modes suitable for a particular application. The number of point sources and direction of loading for the excitation of a few representative modes was investigated. Based on the SAFE analysis, a standard finite element modelling package, Abaqus, was used to excite the designed modes in a three-dimensional plate. The generated wave patterns in Abaqus were then compared with mode shapes predicted in the SAFE model. Good agreement was observed between the

  6. Combining multiple sources of data to inform conservation of Lesser Prairie-Chicken populations

    Ross, Beth; Haukos, David A.; Hagen, Christian A.; Pitman, James

    2018-01-01

    Conservation of small populations is often based on limited data from spatially and temporally restricted studies, resulting in management actions based on an incomplete assessment of the population drivers. If fluctuations in abundance are related to changes in weather, proper management is especially important, because extreme weather events could disproportionately affect population abundance. Conservation assessments, especially for vulnerable populations, are aided by a knowledge of how extreme events influence population status and trends. Although important for conservation efforts, data may be limited for small or vulnerable populations. Integrated population models maximize information from various sources of data to yield population estimates that fully incorporate uncertainty from multiple data sources while allowing for the explicit incorporation of environmental covariates of interest. Our goal was to assess the relative influence of population drivers for the Lesser Prairie-Chicken (Tympanuchus pallidicinctus) in the core of its range, western and southern Kansas, USA. We used data from roadside lek count surveys, nest monitoring surveys, and survival data from telemetry monitoring combined with climate (Palmer drought severity index) data in an integrated population model. Our results indicate that variability in population growth rate was most influenced by variability in juvenile survival. The Palmer drought severity index had no measurable direct effects on adult survival or mean number of offspring per female; however, there were declines in population growth rate following severe drought. Because declines in population growth rate occurred at a broad spatial scale, declines in response to drought were likely due to decreases in chick and juvenile survival rather than emigration outside of the study area. Overall, our model highlights the importance of accounting for environmental and demographic sources of variability, and provides a thorough

  7. Estimating the prevalence of illicit opioid use in New York City using multiple data sources

    McNeely Jennifer

    2012-06-01

    Full Text Available Abstract Background Despite concerns about its health and social consequences, little is known about the prevalence of illicit opioid use in New York City. Individuals who misuse heroin and prescription opioids are known to bear a disproportionate burden of morbidity and mortality. Service providers and public health authorities are challenged to provide appropriate interventions in the absence of basic knowledge about the size and characteristics of this population. While illicit drug users are underrepresented in population-based surveys, they may be identified in multiple administrative data sources. Methods We analyzed large datasets tracking hospital inpatient and emergency room admissions as well as drug treatment and detoxification services utilization. These were applied in combination with findings from a large general population survey and administrative records tracking prescriptions, drug overdose deaths, and correctional health services, to estimate the prevalence of heroin and non-medical prescription opioid use among New York City residents in 2006. These data were further applied to a descriptive analysis of opioid users entering drug treatment and hospital-based medical care. Results These data sources identified 126,681 cases of opioid use among New York City residents in 2006. After applying adjustment scenarios to account for potential overlap between data sources, we estimated over 92,000 individual opioid users. By contrast, just 21,600 opioid users initiated drug treatment in 2006. Opioid users represented 4 % of all individuals hospitalized, and over 44,000 hospitalizations during the calendar year. Conclusions Our findings suggest that innovative approaches are needed to provide adequate services to this sizeable population of opioid users. Given the observed high rates of hospital services utilization, greater integration of drug services into medical settings could be one component of an effective approach to

  8. Fontes suplementares de proteína para novilhos mestiços em recria em pastagens de capim-braquiária no período das águas: desempenho produtivo e econômico Protein sources in multiple supplements for finishing crossbred steers on Brachiaria pasture, in the wet season: productive and economical performance

    Marlos Oliveira Porto

    2009-08-01

    replications. The following treatments were evaluated: mineral mix (MM control group; soybean meal (SM + cottonseed meal (CM and MM; SM and MM; ground soybean grain (GGS and MM; whole soybean grain (WSG and MM; supplied daily on the amount of 60, 510, 460, 560 and 560 g/animal, respectively. Even without statistical significance, the animals that received the supplement showed a gain of 211 g (23.78% greater than the animals that received only mineral mix. The use of multiple supplements based on soybean meal and cottonseed meal provided 247g/animal/day greater than the mineral mix. The supplementation with protein sources may provide additional gain during the wet season. Multiple supplementation provided economic return regardless of the protein source evaluated in relation to the control group.

  9. Chicken fat and inorganic nitrogen source for lipase production by ...

    SAM

    2014-03-19

    Mar 19, 2014 ... for lipase production, the production cost was $US 518.00/million Units of lipase. Key words: ... energetics, fine chemicals and pulp and paper industries. ... for enzyme production is extremely important in dictating ... fat is waste product of poultry processing industry ... Economic Research Service,” 2013).

  10. Using multiple isotopes to understand the source of ingredients used in golden beverages

    Wynn, J. G.

    2011-12-01

    Traditionally, beer contains 4 simple ingredients: water, barley, hops and yeast. Each of these ingredients used in the brewing process contributes some combination of a number of "traditional" stable isotopes (i.e., isotopes of H, C, O, N and S) to the final product. As an educational exercise in an "Analytical Techniques in Geology" course, a group of students analyzed the isotopic composition of the gas, liquid and solid phases of a variety of beer samples collected from throughout the world (including other beverages). The hydrogen and oxygen isotopic composition of the water followed closely the isotopic composition of local meteoric water at the source of the brewery, although there is a systematic offset from the global meteoric water line that may be due to the effects of CO2-H2O equilibration. The carbon isotopic composition of the CO2 reflected that of the solid residue (the source of carbon used as a fermentation substrate), but may potentially be modified by addition of gas-phase CO2 from an inorganic source. The carbon isotopic composition of the solid residue similarly tracks that of the fermentation substrate, and may indicate some alcohol fermented from added sugars in some cases. The nitrogen isotopic composition of the solid residue was relatively constant, and may track the source of nitrogen in the barley, hops and yeast. Each of the analytical methods used is a relatively standard technique used in geological applications, making this a "fun" exercise for those involved, and gives the students hands-on experience with a variety of analytes from a non-traditional sample material.

  11. Pesticide pollution of multiple drinking water sources in the Mekong Delta, Vietnam: evidence from two provinces.

    Chau, N D G; Sebesvari, Z; Amelung, W; Renaud, F G

    2015-06-01

    Pollution of drinking water sources with agrochemicals is often a major threat to human and ecosystem health in some river deltas, where agricultural production must meet the requirements of national food security or export aspirations. This study was performed to survey the use of different drinking water sources and their pollution with pesticides in order to inform on potential exposure sources to pesticides in rural areas of the Mekong River delta, Vietnam. The field work comprised both household surveys and monitoring of 15 frequently used pesticide active ingredients in different water sources used for drinking (surface water, groundwater, water at public pumping stations, surface water chemically treated at household level, harvested rainwater, and bottled water). Our research also considered the surrounding land use systems as well as the cropping seasons. Improper pesticide storage and waste disposal as well as inadequate personal protection during pesticide handling and application were widespread amongst the interviewed households, with little overall risk awareness for human and environmental health. The results show that despite the local differences in the amount and frequency of pesticides applied, pesticide pollution was ubiquitous. Isoprothiolane (max. concentration 8.49 μg L(-1)), fenobucarb (max. 2.32 μg L(-1)), and fipronil (max. 0.41 μg L(-1)) were detected in almost all analyzed water samples (98 % of all surface samples contained isoprothiolane, for instance). Other pesticides quantified comprised butachlor, pretilachlor, propiconazole, hexaconazole, difenoconazole, cypermethrin, fenoxapro-p-ethyl, tebuconazole, trifloxystrobin, azoxystrobin, quinalphos, and thiamethoxam. Among the studied water sources, concentrations were highest in canal waters. Pesticide concentrations varied with cropping season but did not diminish through the year. Even in harvested rainwater or purchased bottled water, up to 12 different pesticides were detected at

  12. ERC sources for the production of highly charged ions (invited)

    Lyneis, C.M.; Antaya, T.A.

    1990-01-01

    Electron cyclotron resonance ion sources (ECRIS) using rf between 5 and 16 GHz have been developed into stable, reliable sources of highly charged ions produced from a wide range of elements. These devices are currently used as ion sources for cyclotrons, synchrotrons, and heavy-ion linacs for nuclear and relativistic heavy-ion physics. They also serve the atomic physics community as a source of low energy multiply charged ions. In order to improve their performance both with respect to maximum charge state and beam intensity, ECRIS builders are now designing and constructing sources which will operate at frequencies up to 30 GHz. In this article we review the present status of operating ECRIS, review recent experimental measurements on plasma parameters, and look at the technology and potential of sources operating at frequencies up to 30 GHz

  13. Multiple sources driving the organic matter dynamics in two contrasting tropical mangroves

    Ray, R.; Shahraki, M.

    2016-01-01

    In this study, we have selected two different mangroves based on their geological, hydrological and climatological variations to investigate the origin (terrestrial, phytobenthos derived, and phytoplankton derived) of dissolved organic carbon (DOC), particulate organic carbon (POC) in the water column and the sedimentary OC using elemental ratios and stable isotopes. Qeshm Island, representing the Iranian mangroves received no attention before this study in terms of DOC, POC biogeochemistry and their sources unlike the Sundarbans (Indian side), the world's largest mangrove system. Slightly higher DOC concentrations in the Iranian mangroves were recorded in our field campaigns between 2011 and 2014, compared to the Sundarbans (315 ± 25 μM vs. 278 ± 42 μM), owing to the longer water residence times, while 9–10 times greater POC concentration (303 ± 37 μM, n = 82) was linked to both suspended load (345 ± 104 mg L"− "1) and high algal production. Yearlong phytoplankton bloom in the mangrove-lined Persian Gulf was reported to be the perennial source of both POC and DOC contributing 80–86% to the DOC and 90–98% to the POC pool. Whereas in the Sundarbans, riverine input contributed 50–58% to the DOC pool and POC composition was regulated by the seasonal litter fall, river discharge and phytoplankton production. Algal derived organic matter (microphytobenthos) represented the maximum contribution (70–76%) to the sedimentary OC at Qeshm Island, while mangrove leaf litters dominated the OC pool in the Indian Sundarbans. Finally, hydrographical settings (i.e. riverine transport) appeared to be the determinant factor in differentiating OM sources in the water column between the dry and wet mangroves. - Highlights: • Sources of OC have been identified and compared between two contrasting mangroves. • Phytoplankton dominated the DOC and POC pool in the Iranian mangroves. • River input contributed half of the total DOC and part of POC in the Indian

  14. Multiple sources driving the organic matter dynamics in two contrasting tropical mangroves

    Ray, R., E-mail: raghab.ray@gmail.com [Institut Universitaire Européen de la Mer, UBO, UMR 6539 LEMAR, rue Dumont dUrville, 29280 Plouzane (France); Leibniz Center for Tropical Marine Ecology, Fahrenheitstr. 6, 28359 Bremen (Germany); Shahraki, M. [Leibniz Center for Tropical Marine Ecology, Fahrenheitstr. 6, 28359 Bremen (Germany); Alfred Wegener Institute, Helmholtz Centre for Polar and Marine Research, Am Handelshafen 12, 27570 Bremerhaven (Germany)

    2016-11-15

    In this study, we have selected two different mangroves based on their geological, hydrological and climatological variations to investigate the origin (terrestrial, phytobenthos derived, and phytoplankton derived) of dissolved organic carbon (DOC), particulate organic carbon (POC) in the water column and the sedimentary OC using elemental ratios and stable isotopes. Qeshm Island, representing the Iranian mangroves received no attention before this study in terms of DOC, POC biogeochemistry and their sources unlike the Sundarbans (Indian side), the world's largest mangrove system. Slightly higher DOC concentrations in the Iranian mangroves were recorded in our field campaigns between 2011 and 2014, compared to the Sundarbans (315 ± 25 μM vs. 278 ± 42 μM), owing to the longer water residence times, while 9–10 times greater POC concentration (303 ± 37 μM, n = 82) was linked to both suspended load (345 ± 104 mg L{sup −} {sup 1}) and high algal production. Yearlong phytoplankton bloom in the mangrove-lined Persian Gulf was reported to be the perennial source of both POC and DOC contributing 80–86% to the DOC and 90–98% to the POC pool. Whereas in the Sundarbans, riverine input contributed 50–58% to the DOC pool and POC composition was regulated by the seasonal litter fall, river discharge and phytoplankton production. Algal derived organic matter (microphytobenthos) represented the maximum contribution (70–76%) to the sedimentary OC at Qeshm Island, while mangrove leaf litters dominated the OC pool in the Indian Sundarbans. Finally, hydrographical settings (i.e. riverine transport) appeared to be the determinant factor in differentiating OM sources in the water column between the dry and wet mangroves. - Highlights: • Sources of OC have been identified and compared between two contrasting mangroves. • Phytoplankton dominated the DOC and POC pool in the Iranian mangroves. • River input contributed half of the total DOC and part of POC in

  15. Propagation of engineering changes to multiple product data views using history of product structure changes

    Do, N.; Choi, I.; Song, M.S.

    2008-01-01

    Abstract The present paper proposes a comprehensive procedure for engineering change propagation in order to maintain consistency between various product data views. A product data model is also proposed for the propagation procedure, which integrates base product definitions for product design, and

  16. Optimized production planning model for a multi-plant cultivation system under uncertainty

    Ke, Shunkui; Guo, Doudou; Niu, Qingliang; Huang, Danfeng

    2015-02-01

    An inexact multi-constraint programming model under uncertainty was developed by incorporating a production plan algorithm into the crop production optimization framework under the multi-plant collaborative cultivation system. In the production plan, orders from the customers are assigned to a suitable plant under the constraints of plant capabilities and uncertainty parameters to maximize profit and achieve customer satisfaction. The developed model and solution method were applied to a case study of a multi-plant collaborative cultivation system to verify its applicability. As determined in the case analysis involving different orders from customers, the period of plant production planning and the interval between orders can significantly affect system benefits. Through the analysis of uncertain parameters, reliable and practical decisions can be generated using the suggested model of a multi-plant collaborative cultivation system.

  17. DOA Estimation of Multiple LFM Sources Using a STFT-based and FBSS-based MUSIC Algorithm

    K. B. Cui

    2017-12-01

    Full Text Available Direction of arrival (DOA estimation is an important problem in array signal processing. An effective multiple signal classification (MUSIC method based on the short-time Fourier transform (STFT and forward/ backward spatial smoothing (FBSS techniques for the DOA estimation problem of multiple time-frequency (t-f joint LFM sources is addressed. Previous work in the area e. g. STFT-MUSIC algorithm cannot resolve the t-f completely or largely joint sources because they can only select the single-source t-f points. The proposed method con¬structs the spatial t-f distributions (STFDs by selecting the multiple-source t-f points and uses the FBSS techniques to solve the problem of rank loss. In this way, the STFT-FBSS-MUSIC algorithm can resolve the t-f largely joint or completely joint LFM sources. In addition, the proposed algorithm also owns pretty low computational complexity when resolving multiple LFM sources because it can reduce the times of the feature decomposition and spectrum search. The performance of the proposed method is compared with that of the existing t-f based MUSIC algorithms through computer simulations and the results show its good performance.

  18. Neutron production and thermal moderation at the PSI UCN source

    Becker, H. [Paul Scherrer Institute, CH-5232 Villigen PSI (Switzerland); Institute for Particle Physics, Eidgenössische Technische Hochschule, Zürich (Switzerland); Bison, G.; Blau, B.; Chowdhuri, Z.; Eikenberg, J.; Fertl, M. [Paul Scherrer Institute, CH-5232 Villigen PSI (Switzerland); Kirch, K. [Paul Scherrer Institute, CH-5232 Villigen PSI (Switzerland); Institute for Particle Physics, Eidgenössische Technische Hochschule, Zürich (Switzerland); Lauss, B., E-mail: bernhard.lauss@psi.ch [Paul Scherrer Institute, CH-5232 Villigen PSI (Switzerland); Perret, G.; Reggiani, D.; Ries, D.; Schmidt-Wellenburg, P. [Paul Scherrer Institute, CH-5232 Villigen PSI (Switzerland); Talanov, V., E-mail: vadim.talanov@psi.ch [Paul Scherrer Institute, CH-5232 Villigen PSI (Switzerland); Wohlmuther, M.; Zsigmond, G. [Paul Scherrer Institute, CH-5232 Villigen PSI (Switzerland)

    2015-03-21

    We report on gold foil activation measurements performed along a vertical channel along the tank of the ultracold neutron source at the Paul Scherrer Institute. The activities obtained at various distances from the spallation target are in very good agreement with MCNPX simulations which take into account the detailed description of the source as built.

  19. Fission product gamma-ray sources as an alternative to cobalt-60 sources for sewage sludge sterilization

    Herrnberger, V.R.D.

    1975-01-01

    The sterilization of sewage sludge is now performed successfully using 60 Co gamma-ray sources. The question arises whether more economic gamma-ray sources exist that could replace the 60 Co source. The following types of sources are considered: Spent fuel elements; mixtures of solidified fission products; and isolated solidified fission products such as 134 / 137 Cs. For a particular irradiation plant the specific source costs (S.Fr./Ci) and their contribution to the irradiation costs for 1 m 3 of sewage irradiated to a dose of 250 krad(S.Fr./m 3 ) are determined and compared with the costs of a plant using a 60 Co source. The encapsulation costs and the effect of the gamma absorption of the source are taken into account. Different encapsulation and source management techniques are reviewed to find the most economic for each source type. A spent fuel element irradiation facility is recommended for use either in combination with a sewage water purification plant or as part of a power reactor station where it replaces the storage water pool for the spent fuel elements. Additional source capsules are not envisaged, as long as double-walled source containers are used. The fission product mixtures are enclosed in double-walled capsules of two different forms: Small cylindrical rods and hollow cylinders. For caesium and cobalt cylindrical rods only are used. The main conclusions of the study are that the highest irradiation costs arise from the use of a fission product mixture source. The costs are, however, only 15% above those of a 60 Co plant. To be competitive the flow-rate has to be adapted to the decreasing activity of the source, resulting in a reduction to 20% within ten years of source utilization. The integrated irradiation plant with a spent fuel element source offers irradiation costs comparable with those of a 60 Co plant, if the flow-rate is constant during one year of source utilization. The irradiation costs are reduced to 25% of those of a 60 Co plant

  20. Food ordering for children in restaurants: multiple sources of influence on decision making

    Castro, Iana A; Williams, Christine B; Madanat, Hala; Pickrel, Julie L; Jun, Hee-Jin; Zive, Michelle; Gahagan, Sheila; Ayala, Guadalupe X

    2017-01-01

    Objective Restaurants are playing an increasingly important role in children’s dietary intake. Interventions to promote healthy ordering in restaurants have primarily targeted adults. Much remains unknown about how to influence ordering for and by children. Using an ecological lens, the present study sought to identify sources of influence on ordering behaviour for and by children in restaurants. Design A mixed-methods study was conducted using unobtrusive observations of dining parties with children and post-order interviews. Observational data included: child’s gender, person ordering for the child and server interactions with the dining party. Interview data included: child’s age, restaurant visit frequency, timing of child’s decision making, and factors influencing decision making. Setting Ten independent, table-service restaurants in San Diego, CA, USA participated. Subjects Complete observational and interview data were obtained from 102 dining parties with 150 children (aged 3–14 years). Results Taste preferences, family influences and menus impacted ordering. However, most children knew what they intended to order before arriving at the restaurant, especially if they dined there at least monthly. Furthermore, about one-third of children shared their meals with others and all shared meals were ordered from adult (v. children’s) menus. Parents placed most orders, although parental involvement in ordering was less frequent with older children. Servers interacted frequently with children but generally did not recommend menu items or prompt use of the children’s menu. Conclusions Interventions to promote healthy ordering should consider the multiple sources of influence that are operating when ordering for and by children in restaurants. PMID:27334904

  1. Multiple data sources improve DNA-based mark-recapture population estimates of grizzly bears.

    Boulanger, John; Kendall, Katherine C; Stetz, Jeffrey B; Roon, David A; Waits, Lisette P; Paetkau, David

    2008-04-01

    A fundamental challenge to estimating population size with mark-recapture methods is heterogeneous capture probabilities and subsequent bias of population estimates. Confronting this problem usually requires substantial sampling effort that can be difficult to achieve for some species, such as carnivores. We developed a methodology that uses two data sources to deal with heterogeneity and applied this to DNA mark-recapture data from grizzly bears (Ursus arctos). We improved population estimates by incorporating additional DNA "captures" of grizzly bears obtained by collecting hair from unbaited bear rub trees concurrently with baited, grid-based, hair snag sampling. We consider a Lincoln-Petersen estimator with hair snag captures as the initial session and rub tree captures as the recapture session and develop an estimator in program MARK that treats hair snag and rub tree samples as successive sessions. Using empirical data from a large-scale project in the greater Glacier National Park, Montana, USA, area and simulation modeling we evaluate these methods and compare the results to hair-snag-only estimates. Empirical results indicate that, compared with hair-snag-only data, the joint hair-snag-rub-tree methods produce similar but more precise estimates if capture and recapture rates are reasonably high for both methods. Simulation results suggest that estimators are potentially affected by correlation of capture probabilities between sample types in the presence of heterogeneity. Overall, closed population Huggins-Pledger estimators showed the highest precision and were most robust to sparse data, heterogeneity, and capture probability correlation among sampling types. Results also indicate that these estimators can be used when a segment of the population has zero capture probability for one of the methods. We propose that this general methodology may be useful for other species in which mark-recapture data are available from multiple sources.

  2. Systematic identification of yeast cell cycle transcription factors using multiple data sources

    Li Wen-Hsiung

    2008-12-01

    Full Text Available Abstract Background Eukaryotic cell cycle is a complex process and is precisely regulated at many levels. Many genes specific to the cell cycle are regulated transcriptionally and are expressed just before they are needed. To understand the cell cycle process, it is important to identify the cell cycle transcription factors (TFs that regulate the expression of cell cycle-regulated genes. Results We developed a method to identify cell cycle TFs in yeast by integrating current ChIP-chip, mutant, transcription factor binding site (TFBS, and cell cycle gene expression data. We identified 17 cell cycle TFs, 12 of which are known cell cycle TFs, while the remaining five (Ash1, Rlm1, Ste12, Stp1, Tec1 are putative novel cell cycle TFs. For each cell cycle TF, we assigned specific cell cycle phases in which the TF functions and identified the time lag for the TF to exert regulatory effects on its target genes. We also identified 178 novel cell cycle-regulated genes, among which 59 have unknown functions, but they may now be annotated as cell cycle-regulated genes. Most of our predictions are supported by previous experimental or computational studies. Furthermore, a high confidence TF-gene regulatory matrix is derived as a byproduct of our method. Each TF-gene regulatory relationship in this matrix is supported by at least three data sources: gene expression, TFBS, and ChIP-chip or/and mutant data. We show that our method performs better than four existing methods for identifying yeast cell cycle TFs. Finally, an application of our method to different cell cycle gene expression datasets suggests that our method is robust. Conclusion Our method is effective for identifying yeast cell cycle TFs and cell cycle-regulated genes. Many of our predictions are validated by the literature. Our study shows that integrating multiple data sources is a powerful approach to studying complex biological systems.

  3. Accumulation status, sources and phytoavailability of metals in greenhouse vegetable production systems in Beijing, China.

    Xu, Li; Lu, Anxiang; Wang, Jihua; Ma, Zhihong; Pan, Ligang; Feng, Xiaoyuan; Luan, Yunxia

    2015-12-01

    The accumulation status, sources and phytoavailability of selected metals in greenhouse vegetable production systems in peri-urban areas of Beijing were investigated. The mean concentrations of As, Cd, Cr, Hg and Pb in greenhouse soils were 8.44, 0.25, 69.0, 0.09 and 22.0 mg kg(-1), dw, respectively. According to principal component analysis, As, Cd, Cr and Hg are mainly from anthropogenic source, but Pb is likely from natural source. Metal concentrations in all vegetable samples were decreased in the order of Cr>As>Pb>Cd>Hg. Compared with root and fruit vegetables, leaf vegetables had relatively high concentrations and transfer factors of heavy metals, except for Cd. By including soil pH, OM and greenhouse soil metals, 10 empirical models were derived using stepwise multiple linear regression analysis to predict heavy metal concentrations in the edible parts of different vegetables. Among the different vegetable groups, the highest intakes of metals occurred through consumption of leaf vegetables for the two age groups, except for Cd. The HI value of the studied metals were all below 1, indicating that consumption of vegetables grown in greenhouse soils was of low risk to consumers in our study area. Copyright © 2015 Elsevier Inc. All rights reserved.

  4. Proteome Profiles of Digested Products of Commercial Meat Sources

    Li, Li; Liu, Yuan; Zhou, Guanghong; Xu, Xinglian; Li, Chunbao

    2017-01-01

    This study was designed to characterize in vitro-digested products of proteins from four commercial meat products, including dry-cured ham, cooked ham, emulsion-type sausage, and dry-cured sausage. The samples were homogenized and incubated with pepsin and trypsin. The digestibility and particle sizes of digested products were measured. Nano-LC–MS/MS was applied to characterize peptides. The results showed the highest digestibility and the lowest particle size in dry-cured ham (P meat products. Our findings give an insight into nutritional values of different meat products. PMID:28396857

  5. A Tracking Analyst for large 3D spatiotemporal data from multiple sources (case study: Tracking volcanic eruptions in the atmosphere)

    Gad, Mohamed A.; Elshehaly, Mai H.; Gračanin, Denis; Elmongui, Hicham G.

    2018-02-01

    This research presents a novel Trajectory-based Tracking Analyst (TTA) that can track and link spatiotemporally variable data from multiple sources. The proposed technique uses trajectory information to determine the positions of time-enabled and spatially variable scatter data at any given time through a combination of along trajectory adjustment and spatial interpolation. The TTA is applied in this research to track large spatiotemporal data of volcanic eruptions (acquired using multi-sensors) in the unsteady flow field of the atmosphere. The TTA enables tracking injections into the atmospheric flow field, the reconstruction of the spatiotemporally variable data at any desired time, and the spatiotemporal join of attribute data from multiple sources. In addition, we were able to create a smooth animation of the volcanic ash plume at interactive rates. The initial results indicate that the TTA can be applied to a wide range of multiple-source data.

  6. Development of an asymmetric multiple-position neutron source (AMPNS) method to monitor the criticality of a degraded reactor core

    Kim, S.S.; Levine, S.H.

    1985-01-01

    An analytical/experimental method has been developed to monitor the subcritical reactivity and unfold the k/sub infinity/ distribution of a degraded reactor core. The method uses several fixed neutron detectors and a Cf-252 neutron source placed sequentially in multiple positions in the core. Therefore, it is called the Asymmetric Multiple Position Neutron Source (AMPNS) method. The AMPNS method employs nucleonic codes to analyze the neutron multiplication of a Cf-252 neutron source. An optimization program, GPM, is utilized to unfold the k/sub infinity/ distribution of the degraded core, in which the desired performance measure minimizes the error between the calculated and the measured count rates of the degraded reactor core. The analytical/experimental approach is validated by performing experiments using the Penn State Breazeale TRIGA Reactor (PSBR). A significant result of this study is that it provides a method to monitor the criticality of a damaged core during the recovery period

  7. Development and production of cobalt-60 sources for metallurgical application

    Oliveira, Paulo Fernando; Valente, Eduardo Sarmento; Maretti Junior, Fausto

    2002-01-01

    The CDTN has developed and produced 60 Co sources to be used in level controllers on continuous ingot casting. The sources used in these systems are sealed with a stainless steel revetment and have an useful life equivalent to one half life of the 60 Co (5.272 years). Each system of continuous ingot casting uses a source with one specified activity and different activation section. The sources have been imported with a very high cost due the special shields used to keep and transport them safety. One of its sources, with initial activity of 148 MBq, after being used for more than 5 years in one factory, was given to CDTN to carry out an activation section studies. After these studies be concluded CDTN/CNEN began the procedures to produce a new source in the IPR-R1 TRIGA Reactor, with an irradiation of one cobalt wire in the maximum flux region of the core. The same metallic cobalt wire was irradiated (10% of total activity), to determinate the necessary irradiation time to obtain the final activation. The CDTN developed too a stainless steel recipient with a aluminum nucleus, to seal and to guarantee the integrity of the source. (author)

  8. TRAM (Transcriptome Mapper: database-driven creation and analysis of transcriptome maps from multiple sources

    Danieli Gian

    2011-02-01

    clusters with differential expression during the differentiation toward megakaryocyte were identified. Conclusions TRAM is designed to create, and statistically analyze, quantitative transcriptome maps, based on gene expression data from multiple sources. The release includes FileMaker Pro database management runtime application and it is freely available at http://apollo11.isto.unibo.it/software/, along with preconfigured implementations for mapping of human, mouse and zebrafish transcriptomes.

  9. High brightness fiber laser pump sources based on single emitters and multiple single emitters

    Scheller, Torsten; Wagner, Lars; Wolf, Jürgen; Bonati, Guido; Dörfel, Falk; Gabler, Thomas

    2008-02-01

    Driven by the potential of the fiber laser market, the development of high brightness pump sources has been pushed during the last years. The main approaches to reach the targets of this market had been the direct coupling of single emitters (SE) on the one hand and the beam shaping of bars and stacks on the other hand, which often causes higher cost per watt. Meanwhile the power of single emitters with 100μm emitter size for direct coupling increased dramatically, which also pushed a new generation of wide stripe emitters or multi emitters (ME) of up to 1000μm emitter size respectively "minibars" with apertures of 3 to 5mm. The advantage of this emitter type compared to traditional bars is it's scalability to power levels of 40W to 60W combined with a small aperture which gives advantages when coupling into a fiber. We show concepts using this multiple single emitters for fiber coupled systems of 25W up to 40W out of a 100μm fiber NA 0.22 with a reasonable optical efficiency. Taking into account a further efficiency optimization and an increase in power of these devices in the near future, the EUR/W ratio pushed by the fiber laser manufacturer will further decrease. Results will be shown as well for higher power pump sources. Additional state of the art tapered fiber bundles for photonic crystal fibers are used to combine 7 (19) pump sources to output powers of 100W (370W) out of a 130μm (250μm) fiber NA 0.6 with nominal 20W per port. Improving those TFB's in the near future and utilizing 40W per pump leg, an output power of even 750W out of 250μm fiber NA 0.6 will be possible. Combined Counter- and Co-Propagated pumping of the fiber will then lead to the first 1kW fiber laser oscillator.

  10. Synergistic effect of multiple indoor allergen sources on atopic symptoms in primary school children

    Chen, W-Y.; Tseng, H-I.; Wu, M-T.; Hung, H-C.; Wu, H-T.; Chen, H-L.; Lu, C.-C.

    2003-01-01

    Accumulating data show that the complex modern indoor environment contributes to increasing prevalence of atopic diseases. However, the dose-response relationship between allergic symptoms and complexity of indoor environmental allergen sources (IEAS) has not been clearly evaluated before. Therefore, we designed this study to investigate the overall effect of multiple IEAS on appearance of asthma (AS), allergic rhinitis (AR), and eczema (EC) symptoms in 1472 primary school children. Among various IEAS analyzed, only stuffed toys, cockroaches, and mold patches fit the model of 'more IEAS, higher odds ratio (OR) of association'. The association of IEAS and AR increased stepwise as more IEAS appeared in the environment (1.71, 2.47, to 2.86). In AS and EC, the association was significant only when all three IEAS were present (1.42, 1.98, to 4.11 in AS; 1.40, 1.76, to 2.95 in EC). These results showed that different IEAS had a synergistic effect on their association with atopic symptoms and also suggest that there is a dose-response relationship between kinds of IEAS and risk of appearance of atopic diseases

  11. Integrating Multiple Data Sources for Combinatorial Marker Discovery: A Study in Tumorigenesis.

    Bandyopadhyay, Sanghamitra; Mallik, Saurav

    2018-01-01

    Identification of combinatorial markers from multiple data sources is a challenging task in bioinformatics. Here, we propose a novel computational framework for identifying significant combinatorial markers ( s) using both gene expression and methylation data. The gene expression and methylation data are integrated into a single continuous data as well as a (post-discretized) boolean data based on their intrinsic (i.e., inverse) relationship. A novel combined score of methylation and expression data (viz., ) is introduced which is computed on the integrated continuous data for identifying initial non-redundant set of genes. Thereafter, (maximal) frequent closed homogeneous genesets are identified using a well-known biclustering algorithm applied on the integrated boolean data of the determined non-redundant set of genes. A novel sample-based weighted support ( ) is then proposed that is consecutively calculated on the integrated boolean data of the determined non-redundant set of genes in order to identify the non-redundant significant genesets. The top few resulting genesets are identified as potential s. Since our proposed method generates a smaller number of significant non-redundant genesets than those by other popular methods, the method is much faster than the others. Application of the proposed technique on an expression and a methylation data for Uterine tumor or Prostate Carcinoma produces a set of significant combination of markers. We expect that such a combination of markers will produce lower false positives than individual markers.

  12. Use of Multiple Data Sources to Estimate the Economic Cost of Dengue Illness in Malaysia

    Shepard, Donald S.; Undurraga, Eduardo A.; Lees, Rosemary Susan; Halasa, Yara; Lum, Lucy Chai See; Ng, Chiu Wan

    2012-01-01

    Dengue represents a substantial burden in many tropical and sub-tropical regions of the world. We estimated the economic burden of dengue illness in Malaysia. Information about economic burden is needed for setting health policy priorities, but accurate estimation is difficult because of incomplete data. We overcame this limitation by merging multiple data sources to refine our estimates, including an extensive literature review, discussion with experts, review of data from health and surveillance systems, and implementation of a Delphi process. Because Malaysia has a passive surveillance system, the number of dengue cases is under-reported. Using an adjusted estimate of total dengue cases, we estimated an economic burden of dengue illness of US$56 million (Malaysian Ringgit MYR196 million) per year, which is approximately US$2.03 (Malaysian Ringgit 7.14) per capita. The overall economic burden of dengue would be even higher if we included costs associated with dengue prevention and control, dengue surveillance, and long-term sequelae of dengue. PMID:23033404

  13. Maximum Likelihood DOA Estimation of Multiple Wideband Sources in the Presence of Nonuniform Sensor Noise

    K. Yao

    2007-12-01

    Full Text Available We investigate the maximum likelihood (ML direction-of-arrival (DOA estimation of multiple wideband sources in the presence of unknown nonuniform sensor noise. New closed-form expression for the direction estimation Cramér-Rao-Bound (CRB has been derived. The performance of the conventional wideband uniform ML estimator under nonuniform noise has been studied. In order to mitigate the performance degradation caused by the nonuniformity of the noise, a new deterministic wideband nonuniform ML DOA estimator is derived and two associated processing algorithms are proposed. The first algorithm is based on an iterative procedure which stepwise concentrates the log-likelihood function with respect to the DOAs and the noise nuisance parameters, while the second is a noniterative algorithm that maximizes the derived approximately concentrated log-likelihood function. The performance of the proposed algorithms is tested through extensive computer simulations. Simulation results show the stepwise-concentrated ML algorithm (SC-ML requires only a few iterations to converge and both the SC-ML and the approximately-concentrated ML algorithm (AC-ML attain a solution close to the derived CRB at high signal-to-noise ratio.

  14. Freezing of enkephalinergic functions by multiple noxious foci: a source of pain sensitization?

    François Cesselin

    Full Text Available BACKGROUND: The functional significance of proenkephalin systems in processing pain remains an open question and indeed is puzzling. For example, a noxious mechanical stimulus does not alter the release of Met-enkephalin-like material (MELM from segments of the spinal cord related to the stimulated area of the body, but does increase its release from other segments. METHODOLOGY/PRINCIPAL FINDINGS: Here we show that, in the rat, a noxious mechanical stimulus applied to either the right or the left hind paw elicits a marked increase of MELM release during perifusion of either the whole spinal cord or the cervico-trigeminal area. However, these stimulatory effects were not additive and indeed, disappeared completely when the right and left paws were stimulated simultaneously. CONCLUSION/SIGNIFICANCE: We have concluded that in addition to the concept of a diffuse control of the transmission of nociceptive signals through the dorsal horn, there is a diffuse control of the modulation of this transmission. The "freezing" of Met-enkephalinergic functions represents a potential source of central sensitization in the spinal cord, notably in clinical situations involving multiple painful foci, e.g. cancer with metastases, poly-traumatism or rheumatoid arthritis.

  15. Use of multiple data sources to estimate the economic cost of dengue illness in Malaysia.

    Shepard, Donald S; Undurraga, Eduardo A; Lees, Rosemary Susan; Halasa, Yara; Lum, Lucy Chai See; Ng, Chiu Wan

    2012-11-01

    Dengue represents a substantial burden in many tropical and sub-tropical regions of the world. We estimated the economic burden of dengue illness in Malaysia. Information about economic burden is needed for setting health policy priorities, but accurate estimation is difficult because of incomplete data. We overcame this limitation by merging multiple data sources to refine our estimates, including an extensive literature review, discussion with experts, review of data from health and surveillance systems, and implementation of a Delphi process. Because Malaysia has a passive surveillance system, the number of dengue cases is under-reported. Using an adjusted estimate of total dengue cases, we estimated an economic burden of dengue illness of US$56 million (Malaysian Ringgit MYR196 million) per year, which is approximately US$2.03 (Malaysian Ringgit 7.14) per capita. The overall economic burden of dengue would be even higher if we included costs associated with dengue prevention and control, dengue surveillance, and long-term sequelae of dengue.

  16. Production of iridium-192 radiation sources: Indian Experience

    Sastry, K.V.S.; Kolhe, O.T.; Nagarja, P.S.; Paramr, Y.D.

    2002-01-01

    Board of Radiation and Isotope Technology (BRIT), a unit under the Department of Atomic Energy is fabricating and supplying Ir-192 industrial radiography sources for various models of radiography cameras for use in the industry for non-destructive testing. Basically these sources are fabricated by encapsulating the required quantity of the activity in stainless steel 316 L capsules using Tungsten Inert gas welding process and crimping/attaching to the respective pigtail assemblies of the radiography cameras. The inactive iridium pellets are irradiated in the DHRUVA reactor at a flux on 1.8 X 10 14 n/cm 2 /sec. The performance classification of these source encapsulation for various conditions of normal and accidental nature are tested by subjecting the prototype sources as per the standard laid down by the regulatory authority, Atomic Energy Regulatory Board, in India. The sources are fabricated as per the national and international standards. Activity of the sources varies from 37O GBq (10 Ci ) to 2.96 TBq (80 Ci ) source strength depending on the requirement of the user. The specific activity of the Ir-192 sources supplied is around 7.4 TBq/gm (200 Ci/gm ). Quality control /Assurance for the manufacture of the source begins from the procurement of the raw material and ends with the finished source. Ir- 192 in the form of -0.3 mm diameter (0.1 mm dia wire of Ir-25 % and Pt-75% sheathed in pure platinum of 0.1 mm thick) is being supplied for use in the treatment of cancer of cervix, tongue etc. by brachytherapy. This is supplied in lengths of 50 cm / 100 cm with 37 - 185 GBq/cm ( 1-5 mCi/cm) activity. Annually 925 TBq (25 kCi) of Ir-192 for industrial radiography and about 60 meters of wire for brachytherapy are being fabricated and supplied. Because of the quality of these sources BRIT not only caters to the Indian industry but also is able to export sources to the third world countries. (Author)

  17. Production of H- ions by an RF driven multicusp source

    Leung, K.N.; Bachman, D.A.; McDonald, D.S.

    1992-01-01

    An RF driven H - source has been developed at LBL for use in the Superconducting Super Collider (SSC). To date, an H - current of ∼40 mA can be obtained from a 5.6-cm-diameter aperture with the source operated at a pressure of about 12 mTorr and 50 kW of RF power. Attempts have been made to enhance the H - beam current by introducing a small quantity of cesium vapor into the source chamber. It is found that the H - output current can be increased by a factor larger than three if some cesium is applied in the collar around the exit aperture

  18. THE USE OF MULTIPLE DATA SOURCES IN THE PROCESS OF TOPOGRAPHIC MAPS UPDATING

    A. Cantemir

    2016-06-01

    Full Text Available The methods used in the process of updating maps have evolved and become more complex, especially upon the development of the digital technology. At the same time, the development of technology has led to an abundance of available data that can be used in the updating process. The data sources came in a great variety of forms and formats from different acquisition sensors. Satellite images provided by certain satellite missions are now available on space agencies portals. Images stored in archives of satellite missions such us Sentinel, Landsat and other can be downloaded free of charge.The main advantages are represented by the large coverage area and rather good spatial resolution that enables the use of these images for the map updating at an appropriate scale. In our study we focused our research of these images on 1: 50.000 scale map. DEM that are globally available could represent an appropriate input for watershed delineation and stream network generation, that can be used as support for hydrography thematic layer update. If, in addition to remote sensing aerial photogrametry and LiDAR data are ussed, the accuracy of data sources is enhanced. Ortophotoimages and Digital Terrain Models are the main products that can be used for feature extraction and update. On the other side, the use of georeferenced analogical basemaps represent a significant addition to the process. Concerning the thematic maps, the classic representation of the terrain by contour lines derived from DTM, remains the best method of surfacing the earth on a map, nevertheless the correlation with other layers such as Hidrography are mandatory. In the context of the current national coverage of the Digital Terrain Model, one of the main concerns of the National Center of Cartography, through the Cartography and Photogrammetry Department, is represented by the exploitation of the available data in order to update the layers of the Topographic Reference Map 1:5000, known as

  19. Development of quality assurance procedures for production of sealed radiation source

    Nam, J H; Cho, W K; Han, H S; Hong, S B; Kim, K H; Kim, S D; Lee, Y G; Lim, N J

    2001-01-01

    The quality assurance procedures for sealed radiation sources production using HANARO and RIPF have been developed. The detailed quality assurance procedures are essential to manage the whole work process effectively and ensure the quality of the produced sealed sources. Through applying this quality assurance procedures to the entire production works of the sealed radiation sources, it is expected that the quality of the products, the safety of the works and the satisfaction of the customers will be increased.

  20. DUSTMS-D: DISPOSAL UNIT SOURCE TERM - MULTIPLE SPECIES - DISTRIBUTED FAILURE DATA INPUT GUIDE.

    SULLIVAN, T.M.

    2006-01-01

    Performance assessment of a low-level waste (LLW) disposal facility begins with an estimation of the rate at which radionuclides migrate out of the facility (i.e., the source term). The focus of this work is to develop a methodology for calculating the source term. In general, the source term is influenced by the radionuclide inventory, the wasteforms and containers used to dispose of the inventory, and the physical processes that lead to release from the facility (fluid flow, container degradation, wasteform leaching, and radionuclide transport). Many of these physical processes are influenced by the design of the disposal facility (e.g., how the engineered barriers control infiltration of water). The complexity of the problem and the absence of appropriate data prevent development of an entirely mechanistic representation of radionuclide release from a disposal facility. Typically, a number of assumptions, based on knowledge of the disposal system, are used to simplify the problem. This has been done and the resulting models have been incorporated into the computer code DUST-MS (Disposal Unit Source Term-Multiple Species). The DUST-MS computer code is designed to model water flow, container degradation, release of contaminants from the wasteform to the contacting solution and transport through the subsurface media. Water flow through the facility over time is modeled using tabular input. Container degradation models include three types of failure rates: (a) instantaneous (all containers in a control volume fail at once), (b) uniformly distributed failures (containers fail at a linear rate between a specified starting and ending time), and (c) gaussian failure rates (containers fail at a rate determined by a mean failure time, standard deviation and gaussian distribution). Wasteform release models include four release mechanisms: (a) rinse with partitioning (inventory is released instantly upon container failure subject to equilibrium partitioning (sorption) with

  1. Effects of neutron spectrum and external neutron source on neutron multiplication parameters in accelerator-driven system

    Shahbunder, Hesham; Pyeon, Cheol Ho; Misawa, Tsuyoshi; Lim, Jae-Yong; Shiroya, Seiji

    2010-01-01

    The neutron multiplication parameters: neutron multiplication M, subcritical multiplication factor k s , external source efficiency φ*, play an important role for numerical assessment and reactor power evaluation of an accelerator-driven system (ADS). Those parameters can be evaluated by using the measured reaction rate distribution in the subcritical system. In this study, the experimental verification of this methodology is performed in various ADS cores; with high-energy (100 MeV) proton-tungsten source in hard and soft neutron spectra cores and 14 MeV D-T neutron source in soft spectrum core. The comparison between measured and calculated multiplication parameters reveals a maximum relative difference in the range of 6.6-13.7% that is attributed to the calculation nuclear libraries uncertainty and accuracy for energies higher than 20 MeV and also dependent on the reaction rate distribution position and count rates. The effects of different core neutron spectra and external neutron sources on the neutron multiplication parameters are discussed.

  2. Chicken fat and inorganic nitrogen source for lipase production by ...

    MA41) from Atlantic Forest, using chicken fat and association of organic and inorganic nitrogen sources in submerged fermentation to seek economically attractive bioprocess. A 2-level, 4-factor Central Composite Design (CCD) and response ...

  3. Application of the modified neutron source multiplication method for a measurement of sub-criticality in AGN-201K reactor

    Myung-Hyun Kim

    2010-01-01

    Measurement of sub-criticality is a challenging and required task in nuclear industry both for nuclear criticality safety and physics test in nuclear power plant. A relatively new method named as Modified Neutron Source Multiplication Method (MNSM) was proposed in Japan. This method is an improvement of traditional Neutron Source Multiplication (NSM) Method, in which three correction factors are applied additionally. In this study, MNSM was tested in calculation of rod worth using an educational reactor in Kyung Hee University, AGN-201K. For this study, a revised nuclear data library and a neutron transport code system TRANSX-PARTISN were used for the calculation of correction factors for various control rod positions and source locations. Experiments were designed and performed to enhance errors in NSM from the location effects of source and detectors. MNSM can correct these effects but current results showed not much correction effects. (author)

  4. Products of multiple Fourier series with application to the multiblade transformation

    Kunz, D. L.

    1981-01-01

    A relatively simple and systematic method for forming the products of multiple Fourier series using tensor like operations is demonstrated. This symbolic multiplication can be performed for any arbitrary number of series, and the coefficients of a set of linear differential equations with periodic coefficients from a rotating coordinate system to a nonrotating system is also demonstrated. It is shown that using Fourier operations to perform this transformation make it easily understood, simple to apply, and generally applicable.

  5. Autonomy of image and use of single or multiple sense modalities in original verbal image production.

    Khatena, J

    1978-06-01

    The use of a single or of multiple sense modalities in the production of original verbal images as related to autonomy of imagery was explored. 72 college adults were administered Onomatopoeia and Images and the Gordon Test of Visual Imagery Control. A modified scoring procedure for the Gordon scale differentiated imagers who were moderate or low in autonomy. The two groups produced original verbal images using multiple sense modalities more frequently than a single modality.

  6. Multiple Cropping for Raising Productivity and Farm Income of Small Farmers

    Mina Nath Paudel

    2016-12-01

    Full Text Available Multiple cropping is an agriculture system long adopted by marginalized small holder farmers especially in hills and mountains. This practice was a meant to enhance farm productivity when farming area is limited. Here, in this paper, a brief review on the benefits of multiple cropping is presented focusing on the practices adopted by marginalized farmers, in general. In multiple cropping, it is generally argued that the practice favors an efficient utilization of resources like air, water, light, space, and nutrients by companion crops in both temporal and spatial dimensions due to their differential growth habits and seasonality. Multiple cropping could be one of the viable alternatives to cope uncertainties and changes, where food and nutritional uncertainty looming large. The ultimate outcome of multiple cropping could be visualized in adverse or harsh environment for increase agriculture production, livelihood and income. Various food products are obtained through multiple cropping. Land equivalent ratio (LER, relative yield total (RYT and income equivalent ratio (IER can be increased with mixed/intercropping systems. Multiple cropping helps in getting more than one crop simultaneously, so even if the selling price of one commodity is less, the other might compensate. In the tropics, smallholder farms, which produce over 60% of the food resources of developing nations from intercropping of cereals with many crops mostly legumes, had been the field of much investigation because of synergistic effects of diversifying food production and household cash incomes in these systems. This clearly implies the importance of multiple cropping for small farmers who constitute majority in the developing countries.

  7. Use of multiple tobacco products in a national sample of persons enrolled in addiction treatment.

    Guydish, Joseph; Tajima, Barbara; Pramod, Sowmya; Le, Thao; Gubner, Noah R; Campbell, Barbara; Roman, Paul

    2016-09-01

    To explore use of tobacco products in relationship to marketing exposure among persons in addiction treatment. A random sample of treatment programs was drawn from the National Institute on Drug Abuse (NIDA) Clinical Trials Network (CTN). Participants in each program completed surveys concerning use of tobacco products (N=1113). Exposure to tobacco marketing and counter-marketing, advertising receptivity, and perceived health risks of smoking were tested for their association with use of multiple tobacco products. Prevalence of combustible cigarette use was 77.9%. Weekly or greater use of other products was: e-cigarettes (17.7%), little filtered cigars (8.6%), smokeless tobacco (5.2%), and standard cigars (4.6%) with 24.4% using multiple tobacco products. Compared to single product users, multiple product users smoked more cigarettes per day (OR=1.03, 95% CI 1.01-1.05, padvertising for products other than combustible cigarettes (OR=1.93, CI 1.35-2.75, ptobacco counter-marketing (OR=1.70, 95% CI: 1.09-2.63, p=0.019). Heavier smokers and those trying to quit may be more likely to use e-cigarettes, little filtered cigars, or smokeless tobacco and have greater susceptibility to their advertising. This highlights the importance of regulating advertising related to smoking cessation as their effectiveness for this purpose has not been demonstrated. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

  8. Domestic and foreign knowledge sources for innovation in internationalized Production Networks: the automotive and the iron and steel cases

    Hernan Alejandro Morero

    2015-02-01

    Full Text Available This paper studies the relative relevance of domestic knowledge sources for innovation in internationalized production activities in an emerging economy. Two Production Networks from Argentina with a different kind of internationalization were considered: organized around subsidiaries of multinational companies (the automotive case and organized around local headquarters (the iron and steel case. A multiple factor analysis was carried out and cluster techniques were applied using a specific innovation survey done to 163 automotive and iron and steel firms from Argentina from the period of 2001 to2005, to evaluate the relative importance of domestic and foreign knowledge sources. The main finding is that in a production network organized around domestic headquarters the best innovative performance underrates the importance of international linkages, in comparison with networks organized around foreign subsidiaries.

  9. Non-timber forest products: alternative multiple-uses for sustainable forest management

    James L. Chamberlain; Mary Predny

    2003-01-01

    Forests of the southern United States are the source of a great diversity of flora, much of which is gathered for non-timber forest products (NTFPs). These products are made from resources that grow under the forest canopy as trees, herbs, shrubs, vines, moss and even lichen. They occur naturally in forests or may be cultivated under the forest canopy or in...

  10. A proton-driven, intense, subcritical, fission neutron source for radioisotope production

    Jongen, Y. [Chemin du Cyclotron, Louvain-la-Neuve (Belgium)

    1995-10-01

    {sup 99m}Tc, the most frequently used radioisotope in nuclear medicine, is distributed as {sup 99}Mo=>{sup 99m}Tc generators. {sup 99}Mo is a fission product of {sup 235}U. To replace the aging nuclear reactors used today for this production, the author proposes to use a spallation neutron source, with neutron multiplication by fission. A 150 MeV, H{sup {minus}} cyclotron can produce a 225 kW proton beam with 50% total system energy efficiency. The proton beam would hit a molten lead target, surrounded by a water moderator and a graphite reflector, producing around 0.96 primary neutron per proton. The primary spallation neutrons, moderated, would strike secondary targets containing a subcritical amount of {sup 235}U. The assembly would show a k{sub eff} of 0.8, yielding a fivefold neutron multiplication. The thermal neutron flux at the targets location would be 2 {times} 10{sup 14} n/cm{sup 2}.s, resulting in a fission power of 500 to 750 kW. One such system could supply the world demand in {sup 99}Mo, as well as other radioisotopes. Preliminary indications show that the cost would be lower than the cost of a commercial 10 MW isotope production reactor. The cost of operation, of disposal of radiowaste and of decommissioning should be significantly lower as well. Finally, the non-critical nature of the system would make it more acceptable for the public than a nuclear reactor and should simplify the licensing process.

  11. Wheat multiple synthetic derivatives: a new source for heat stress tolerance adaptive traits

    Elbashir, Awad Ahmed Elawad; Gorafi, Yasir Serag Alnor; Tahir, Izzat Sidahmed Ali; Kim, June-Sik; Tsujimoto, Hisashi

    2017-01-01

    Heat stress is detrimental to wheat (Triticum aestivum L.) productivity. In this study, we aimed to select heat-tolerant plants from a multiple synthetic derivatives (MSD) population and evaluate their agronomic and physiological traits. We selected six tolerant plants from the population with the background of the cultivar ‘Norin 61’ (N61) and established six MNH (MSD population of N61 selected as heat stress-tolerant) lines. We grew these lines with N61 in the field and growth chamber. In the field, we used optimum and late sowings to ensure plant exposure to heat. In the growth chamber, in addition to N61, we used the heat-tolerant cultivars ‘Gelenson’ and ‘Bacanora’. We confirmed that MNH2 and MNH5 lines acquired heat tolerance. These lines had higher photosynthesis and stomata conductance and exhibited no reduction in grain yield and biomass under heat stress compared to N61. We noticed that N61 had relatively good adaptability to heat stress. Our results indicate that the MSD population includes the diversity of Aegilops tauschii and is a promising resource to uncover useful quantitative traits derived from this wild species. Selected lines could be useful for heat stress tolerance breeding. PMID:28744178

  12. The influence of different nitrogen and carbon sources on mycotoxin production in Alternaria alternata.

    Brzonkalik, Katrin; Herrling, Tanja; Syldatk, Christoph; Neumann, Anke

    2011-05-27

    The aim of this study was to determine the influence of different carbon and nitrogen sources on the production of the mycotoxins alternariol (AOH), alternariol monomethyl ether (AME) and tenuazonic acid (TA) by Alternaria alternata at 28°C using a semi-synthetic medium (modified Czapek-Dox broth) supplemented with nitrogen and carbon sources. Additionally the effect of shaken and static cultivation on mycotoxin production was tested. Initial experiments showed a clear dependency between nitrogen depletion and mycotoxin production. To assess whether nitrogen limitation in general or the type of nitrogen source triggers the production, various nitrogen sources including several ammonium/nitrate salts and amino acids were tested. In static culture the production of AOH/AME can be enhanced greatly with phenylalanine whereas some nitrogen sources seem to inhibit the AOH/AME production completely. TA was not significantly affected by the choice of nitrogen source. In shaken culture the overall production of all mycotoxins was lower compared to static cultivation. Furthermore tests with a wide variety of carbon sources including monosaccharides, disaccharides, complex saccharides such as starch as well as glycerol and acetate were performed. In shaken culture AOH was produced when glucose, fructose, sucrose, acetate or mixtures of glucose/sucrose and glucose/acetate were used as carbon sources. AME production was not detected. The use of sodium acetate resulted in the highest AOH production. In static culture AOH production was also stimulated by acetate and the amount is comparable to shaken conditions. Under static conditions production of AOH was lower except when cultivated with acetate. In static cultivation 9 of 14 tested carbon sources induced mycotoxin production compared to 4 in shaken culture. This is the first study which analyses the influence of carbon and nitrogen sources in a semi-synthetic medium and assesses the effects of culture conditions on

  13. Multiple uses for an old ibm-pc 486 in nuclear medicine using open source software

    Anselmi, C.E.; Anselmi, O.E.

    2002-01-01

    Multiple uses for an old ibm-pc 486 in nuclear medicine using open source software. Aim: To use a low budget platform to: 1 - send patient's images from processing workstation to the nuclear medicine information system; 2 - backup data files from acquisition in DICOM format in cd-rom; 3 - move data across different hospitals allowing remote processing and reading of studies. Both nuclear medicine systems in the two hospitals are Siemens Icon workstations. Material and methods: The computer used is an ibm-pc 486, which sells for about US dollar 70. The operating system installed is Red Hat Linux 6.2. The sending of the patient's images to the information system is performed through AppleTalk and Samba. The backup of acquisition files is performed by the communication from the workstation through DICOM to the Storage Class Provider (Office Dicom Toolkit) running in the 486, and the files are later burned on cd-rom. A similar configuration is present in another hospital, with minor differences in processor type. Data from any of the hospitals can be sent to the other one through the remote synchronization performed by Rsync. The connection between both Linux computers is encrypted through Secure Shell (open SSH). All software installed in the 486 was downloaded from the internet at no cost. No software was installed in the workstations. Results: The whole system is recognized transparently by the workstation's system as a local storage disk, such as the acquisition cameras or the other workstations. The transfer of images from the workstation to the information system or to a remote hospital is done the same way as copying data from the acquisition cameras in the vendor's software. When transferring large files across hospitals, the synchronization may take 1 to 3 minutes through broad band internet. The backup in DICOM format in cd-rom allows review of patient data in any computer equipped with a DICOM viewing software, as well as the re-processing of that

  14. Marine organisms: an alternative source of potentially valuable natural products

    Alphonse Kelecom

    1991-01-01

    Full Text Available This paper recalls the outcoming of marine natural products research and reviews a selection of marirne bioactive metabolites in current use together with promising trends in marine pharmacology.

  15. Characterization of cellulase production by carbon sources in two ...

    user7

    2013-11-27

    Nov 27, 2013 ... 7State Key Laboratory of Urban Water Resource and Environment, Harbin ... China. Accepted 28 March, 2012. The induction of cellulase production in two .... prevent the contamination with bacteria, 0.02% sodium azide was.

  16. Influence of nitrogen sources on production of β- galactosidase by ...

    USER

    2010-05-17

    May 17, 2010 ... that enzyme production enhanced 2.7 fold by use of suitable ... tages of applying microbial enzymes for industries are ... downstream processing are essential to reduce the cost ... of economic importance in the country.

  17. Sources of Research Ideas Among Productive Scholars. Implications for Administrators

    Glueck, William F.; Jauch, Lawrence R.

    1975-01-01

    Administrators wishing to stimulate research productivity should try to lure the most creative researchers but should also put emphasis on libraries and information retrieval services, and funds to attend professional meetings. (Editor)

  18. Production of effective microorganism using halal based sources: A ...

    Malaysia is recognized as a modern Islamic country; citizens have concerns regarding halal issues associated with EM ingredients, which are not clearly mentioned by the manufacturer. Hence, a halal-based source is suggested in the utilization of EM technology. This study presents the development and applications of ...

  19. Production of effective microorganism using halal- based sources: A ...

    GREGORY

    2011-12-16

    Dec 16, 2011 ... Key words: Component, effective microorganisms (EM), agriculture, halal-based source. INTRODUCTION. In recent years, with focus on feeding a rapidly growing human population, Malaysia has jeopardized the environ- ment and its natural resources, which are already under great stress. Consequently ...

  20. Exploiting Deep Neural Networks and Head Movements for Robust Binaural Localization of Multiple Sources in Reverberant Environments

    Ma, Ning; May, Tobias; Brown, Guy J.

    2017-01-01

    This paper presents a novel machine-hearing system that exploits deep neural networks (DNNs) and head movements for robust binaural localization of multiple sources in reverberant environments. DNNs are used to learn the relationship between the source azimuth and binaural cues, consisting...... of the complete cross-correlation function (CCF) and interaural level differences (ILDs). In contrast to many previous binaural hearing systems, the proposed approach is not restricted to localization of sound sources in the frontal hemifield. Due to the similarity of binaural cues in the frontal and rear...

  1. Investigation of black and brown carbon multiple-wavelength-dependent light absorption from biomass and fossil fuel combustion source emissions

    Michael R. Olson; Mercedes Victoria Garcia; Michael A. Robinson; Paul Van Rooy; Mark A. Dietenberger; Michael Bergin; James Jay Schauer

    2015-01-01

    Quantification of the black carbon (BC) and brown carbon (BrC) components of source emissions is critical to understanding the impact combustion aerosols have on atmospheric light absorption. Multiple-wavelength absorption was measured from fuels including wood, agricultural biomass, coals, plant matter, and petroleum distillates in controlled combustion settings....

  2. Frequency-swept laser light source at 1050 nm with higher bandwidth due to multiple semiconductor optical amplifiers in series

    Marschall, Sebastian; Thrane, Lars; Andersen, Peter E.

    2009-01-01

    We report on the development of an all-fiber frequency-swept laser light source in the 1050 nm range based on semiconductor optical amplifiers (SOA) with improved bandwidth due to multiple gain media. It is demonstrated that even two SOAs with nearly equal gain spectra can improve the performance...

  3. Multiple tobacco product use among adults in the United States: cigarettes, cigars, electronic cigarettes, hookah, smokeless tobacco, and snus.

    Lee, Youn O; Hebert, Christine J; Nonnemaker, James M; Kim, Annice E

    2014-05-01

    Noncigarette tobacco products are increasingly popular. Researchers need to understand multiple tobacco product use to assess the effects of these products on population health. We estimate national prevalence and examine risk factors for multiple product use. We calculated prevalence estimates of current use patterns involving cigarettes, cigars, electronic cigarettes, hookah, smokeless tobacco, and snus using data from the 2012 RTI National Adult Tobacco Survey (N=3627), a random-digit-dial telephone survey of adults aged 18 and over. Associations between use patterns (exclusive single product and multiple products) and demographic characteristics were examined using Pearson chi-square tests and logistic regression. 32.1% of adults currently use 1 or more tobacco products; 14.9% use cigarettes exclusively, and 6.6% use one noncigarette product exclusively, 6.9% use cigarettes with another product (dual use), 1.3% use two noncigarette products, and 2.4% use three or more products (polytobacco use). Smokers who are young adult, male, never married, reside in the West, and made prior quit attempts were at risk for multiple product use. Over 10% of U.S. adults use multiple tobacco products. A better understanding of multiple product use involving combustible products, like cigars and hookah, is needed. Multiple product use may be associated with past quit attempts. Copyright © 2014 Elsevier Inc. All rights reserved.

  4. The total cost of logistics in supplier selection, under conditions of multiple sourcing, multiple criteria and capacity constraint

    Elnaz Bani

    2016-06-01

    Full Text Available This paper presents a mathematical model to solve a multi-objective decision making supplier selection problem. The proposed problem considers three objective functions: the first objective function minimizes the cost of purchasing the products while the second objective function minimizes the due dates and finally the third objective function maximizes the customer satisfaction. The resulted problem is formulated as mixed integer programming and, therefore, we use invasive weed optimization technique to solve the resulted problem. The performance of the proposed model is compared with NSGA II based on different criteria such as mean ideal distance and quality matrix. The preliminary results indicate that the proposed model performs relatively well compared with alternative method.

  5. Characterization of Greater-Than-Class C sealed sources. Volume 2, Sealed source characterization and future production

    Harris, G.; Griffel, A.

    1994-09-01

    Sealed sources are small, relatively high-activity radioactive sources typically encapsulated in a metallic container. The activities can range from less than 1 mCi to over 1,000 Ci. They are used in a variety of industries and are commonly available. Many of the sources will be classified as Greater-Than-Class C low-level radioactive waste (GTCC LLW) for the purpose of waste disposal. The US Department of Energy is responsible for disposing of this class of low-level radioactive waste. The characterization of a sealed source is essentially a function of the type of radiation it emits, the principal use for which it is applied, and the activity it contains. The types of radiation of most interest to the GTCC LLW Program are gamma rays and neutrons, since these are emitted by the highest activity sources. The principal uses of most importance are gamma irradiators, medical teletherapy, well logging probes, and other general neutron applications. Current annual production rates of potential Greater-Than-Class C (PGTCC) sources sold to specific licensees were estimated based on data collected from device manufacturers. These estimates were then adjusted for current trends in the industry to estimate future annual production rates. It is expected that there will be approximately 8,000 PGTCC sealed sources produced annually for specific licensees

  6. Sequence-based analysis of the microbial composition of water kefir from multiple sources.

    Marsh, Alan J; O'Sullivan, Orla; Hill, Colin; Ross, R Paul; Cotter, Paul D

    2013-11-01

    Water kefir is a water-sucrose-based beverage, fermented by a symbiosis of bacteria and yeast to produce a final product that is lightly carbonated, acidic and that has a low alcohol percentage. The microorganisms present in water kefir are introduced via water kefir grains, which consist of a polysaccharide matrix in which the microorganisms are embedded. We aimed to provide a comprehensive sequencing-based analysis of the bacterial population of water kefir beverages and grains, while providing an initial insight into the corresponding fungal population. To facilitate this objective, four water kefirs were sourced from the UK, Canada and the United States. Culture-independent, high-throughput, sequencing-based analyses revealed that the bacterial fraction of each water kefir and grain was dominated by Zymomonas, an ethanol-producing bacterium, which has not previously been detected at such a scale. The other genera detected were representatives of the lactic acid bacteria and acetic acid bacteria. Our analysis of the fungal component established that it was comprised of the genera Dekkera, Hanseniaspora, Saccharomyces, Zygosaccharomyces, Torulaspora and Lachancea. This information will assist in the ultimate identification of the microorganisms responsible for the potentially health-promoting attributes of these beverages. © 2013 Federation of European Microbiological Societies. Published by John Wiley & Sons Ltd. All rights reserved.

  7. Multiple Flow Loop SCADA System Implemented on the Production Prototype Loop

    Baily, Scott A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Dalmas, Dale Allen [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Wheat, Robert Mitchell [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Woloshun, Keith Albert [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Dale, Gregory E. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-11-16

    The following report covers FY 15 activities to develop supervisory control and data acquisition (SCADA) system for the Northstar Moly99 production prototype gas flow loop. The goal of this effort is to expand the existing system to include a second flow loop with a larger production-sized blower. Besides testing the larger blower, this system will demonstrate the scalability of our solution to multiple flow loops.

  8. Multi products single machine economic production quantity model with multiple batch size

    Ata Allah Taleizadeh

    2011-04-01

    Full Text Available In this paper, a multi products single machine economic order quantity model with discrete delivery is developed. A unique cycle length is considered for all produced items with an assumption that all products are manufactured on a single machine with a limited capacity. The proposed model considers different items such as production, setup, holding, and transportation costs. The resulted model is formulated as a mixed integer nonlinear programming model. Harmony search algorithm, extended cutting plane and particle swarm optimization methods are used to solve the proposed model. Two numerical examples are used to analyze and to evaluate the performance of the proposed model.

  9. Growth and xanthan production of Xanthomonas campestris depending on the N-source concentration

    Prell, A [Academy of Sciences of the Czech Republic, Prague (Czech Republic). Inst. of Microbiology; Lasik, J [Academy of Sciences of the Czech Republic, Prague (Czech Republic). Inst. of Microbiology; Konicek, J [Academy of Sciences of the Czech Republic, Prague (Czech Republic). Inst. of Microbiology; Sobotka, M [Academy of Sciences of the Czech Republic, Prague (Czech Republic). Inst. of Microbiology; Sys, J [Academy of Sciences of the Czech Republic, Prague (Czech Republic). Inst. of Microbiology

    1995-11-01

    Growth of X. campestris and production of xanthan were studied in several batch fermentations with different starting concentrations of N-source. The dependencies of growth, productivity and yields on initial N-source concentration were observed. The maximum yields in the course of cultivations were identified. (orig.)

  10. Production of highly charged ion beams from electron cyclotron resonance ion sources (invited)

    Xie, Z.Q.

    1998-01-01

    Electron cyclotron resonance ion source (ECRIS) development has progressed with multiple-frequency plasma heating, higher mirror magnetic fields, and better technique to provide extra cold electrons. Such techniques greatly enhance the production of highly charged ions from ECRISs. So far at continuous wave (CW) mode operation, up to 300 eμA of O 7+ and 1.15 emA of O 6+ , more than 100 eμA of intermediate heavy ions for charge states up to Ar 13+ , Ca 13+ , Fe 13+ , Co 14+ , and Kr 18+ , and tens of eμA of heavy ions with charge states to Kr 26+ , Xe 28+ , Au 35+ , Bi 34+ , and U 34+ were produced from ECRISs. At an intensity of at least 1 eμA, the maximum charge state available for the heavy ions are Xe 36+ , Au 46+ , Bi 47+ , and U 48+ . An order of magnitude enhancement for fully stripped argon ions (I≥60enA) were also achieved. This article will review the ECR ion source progress and discuss key requirement for ECRISs to produce the highly charged ion beams. copyright 1998 American Institute of Physics

  11. Brosimum Alicastrum as a Novel Starch Source for Bioethanol Production

    Edgar Olguin-Maciel

    2017-10-01

    Full Text Available Ramon (Brosimum alicastrum is a forest tree native to the Mesoamerican region and the Caribbean. The flour obtained from Ramon seeds is 75% carbohydrate, of which 63% is starch, indicating its potential as a novel raw material for bioethanol production. The objective of this study was to produce ethanol from Ramon flour using a 90 °C thermic treatment for 30 min and a native yeast strain (Candida tropicalis for the fermentation process. In addition, the structure of the flour and the effects of pretreatment were observed via scanning electron microscopy. The native yeast strain was superior to the commercial strain, fermenting 98.8% of the reducing sugar (RS at 48 h and generating 31% more ethanol than commercial yeast. One ton of flour yielded 213 L of ethanol. These results suggest that Ramon flour is an excellent candidate for ethanol production. This is the first report on bioethanol production using the starch from Ramon seed flour and a native yeast strain isolated from this feedstock. This alternative material for bioethanol production minimizes the competition between food and energy production, a priority for Mexico that has led to significant changes in public policies to enhance the development of renewable energies.

  12. Thin, Conductive, Pyrrolyc film production for radioactive sources backings

    Rodriguez, L.; Arcos, J.M. los

    1993-01-01

    A procedure for electro polymerization of pyrrole has been set up in order to produce thin, (> 15 μg/cm2) homogeneous (thickness variation < 2%) films, with no need for additional metallization to be used as backings of radioactive sources, having 10-0,4 Kfl/sample, for 35-70 μg/cm . The experimental equipment, reagent and procedure utilized is described as well as the characterization of Pyrrolyc films produced. (Author) 28 refs

  13. K-shell-hole production, multiple-hole production, charge transfer, and antisymmetry

    Reading, J.F.; Ford, A.L.

    1980-01-01

    In calculating K-shell-hole production when an ion collides with an atom, account must be taken of the fact that processes involving electrons other than the K-shell electron can occur. For example, after making a K-shell hole an L-shell electron may be knocked into it, or an L-shell vacancy may be produced and the K-shell electron promoted to that vacancy in the ''Fermi sea'' of the target-atom orbitals. In 1973 a theorem was proved by one of the present authors demonstrating that all these multielectron processes cancel in an independent-particle model for the target atom. In this paper it is shown that the same thing occurs for hole production by charge transfer to the ion. The authors demonstrate that multihole production does not obey this simple rule and that the probability for multihole production is not the product of independent single-electron probabilities. The correct expressions that should be used for these processes are given, together with new results for charge-transfer processes accompanied by hole production

  14. Effect of nitrogen source on curdlan production by Alcaligenes faecalis ATCC 31749.

    Jiang, Longfa

    2013-01-01

    This study aims to investigate the effect of nitrogen source on curdlan production by Alcaligenes faecalis ATCC 31749. Curdlan production fell when excess nitrogen source was present, while biomass accumulation increased as the level of nitrogen source raised. Curdlan production and biomass accumulation were greater with urea compared with those with other nitrogen sources. The highest production of curdlan and biomass accumulation by A. faecalis ATCC 31749 was 28.16 g L(-1) and 9.58 g L(-1), respectively, with urea, whereas those with NH(4)Cl were 15.17 g L(-1) and 6.25 g L(-1), respectively. The optimum fermentation time for curdlan production was also affected by the nitrogen source in the medium. Copyright © 2012 Elsevier B.V. All rights reserved.

  15. A principal-component and least-squares method for allocating polycyclic aromatic hydrocarbons in sediment to multiple sources

    Burns, W.A.; Mankiewicz, P.J.; Bence, A.E.; Page, D.S.; Parker, K.R.

    1997-01-01

    A method was developed to allocate polycyclic aromatic hydrocarbons (PAHs) in sediment samples to the PAH sources from which they came. The method uses principal-component analysis to identify possible sources and a least-squares model to find the source mix that gives the best fit of 36 PAH analytes in each sample. The method identified 18 possible PAH sources in a large set of field data collected in Prince William Sound, Alaska, USA, after the 1989 Exxon Valdez oil spill, including diesel oil, diesel soot, spilled crude oil in various weathering states, natural background, creosote, and combustion products from human activities and forest fires. Spill oil was generally found to be a small increment of the natural background in subtidal sediments, whereas combustion products were often the predominant sources for subtidal PAHs near sites of past or present human activity. The method appears to be applicable to other situations, including other spills

  16. Enhanced production of multi-strange hadrons in high-multiplicity proton–proton collisions

    Adam, Jaroslav; Aggarwal, Madan Mohan; Aglieri Rinella, Gianluca; Agnello, Michelangelo; Agrawal, Neelima; Ahammed, Zubayer; Ahmad, Shakeel; Ahn, Sang Un; Aiola, Salvatore; Akindinov, Alexander; Alam, Sk Noor; Silva De Albuquerque, Danilo; Aleksandrov, Dmitry; Alessandro, Bruno; Alexandre, Didier; Alfaro Molina, Jose Ruben; Alici, Andrea; Alkin, Anton; Alme, Johan; Alt, Torsten; Altinpinar, Sedat; Altsybeev, Igor; Alves Garcia Prado, Caio; An, Mangmang; Andrei, Cristian; Andrews, Harry Arthur; Andronic, Anton; Anguelov, Venelin; Anticic, Tome; Antinori, Federico; Antonioli, Pietro; Aphecetche, Laurent Bernard; Appelshaeuser, Harald; Arcelli, Silvia; Arnaldi, Roberta; Arnold, Oliver Werner; Arsene, Ionut Cristian; Arslandok, Mesut; Audurier, Benjamin; Augustinus, Andre; Averbeck, Ralf Peter; Azmi, Mohd Danish; Badala, Angela; Baek, Yong Wook; Bagnasco, Stefano; Bailhache, Raphaelle Marie; Bala, Renu; Balasubramanian, Supraja; Baldisseri, Alberto; Baral, Rama Chandra; Barbano, Anastasia Maria; Barbera, Roberto; Barile, Francesco; Barnafoldi, Gergely Gabor; Barnby, Lee Stuart; Ramillien Barret, Valerie; Bartalini, Paolo; Barth, Klaus; Bartke, Jerzy Gustaw; Bartsch, Esther; Basile, Maurizio; Bastid, Nicole; Basu, Sumit; Bathen, Bastian; Batigne, Guillaume; Batista Camejo, Arianna; Batyunya, Boris; Batzing, Paul Christoph; Bearden, Ian Gardner; Beck, Hans; Bedda, Cristina; Behera, Nirbhay Kumar; Belikov, Iouri; Bellini, Francesca; Bello Martinez, Hector; Bellwied, Rene; Belmont Iii, Ronald John; Belmont Moreno, Ernesto; Espinoza Beltran, Lucina Gabriela; Belyaev, Vladimir; Bencedi, Gyula; Beole, Stefania; Berceanu, Ionela; Bercuci, Alexandru; Berdnikov, Yaroslav; Berenyi, Daniel; Bertens, Redmer Alexander; Berzano, Dario; Betev, Latchezar; Bhasin, Anju; Bhat, Inayat Rasool; Bhati, Ashok Kumar; Bhattacharjee, Buddhadeb; Bhom, Jihyun; Bianchi, Livio; Bianchi, Nicola; Bianchin, Chiara; Bielcik, Jaroslav; Bielcikova, Jana; Bilandzic, Ante; Biro, Gabor; Biswas, Rathijit; Biswas, Saikat; Bjelogrlic, Sandro; Blair, Justin Thomas; Blau, Dmitry; Blume, Christoph; Bock, Friederike; Bogdanov, Alexey; Boggild, Hans; Boldizsar, Laszlo; Bombara, Marek; Bonora, Matthias; Book, Julian Heinz; Borel, Herve; Borissov, Alexander; Borri, Marcello; Bossu, Francesco; Botta, Elena; Bourjau, Christian; Braun-Munzinger, Peter; Bregant, Marco; Breitner, Timo Gunther; Broker, Theo Alexander; Browning, Tyler Allen; Broz, Michal; Brucken, Erik Jens; Bruna, Elena; Bruno, Giuseppe Eugenio; Budnikov, Dmitry; Buesching, Henner; Bufalino, Stefania; Buncic, Predrag; Busch, Oliver; Buthelezi, Edith Zinhle; Bashir Butt, Jamila; Buxton, Jesse Thomas; Cabala, Jan; Caffarri, Davide; Cai, Xu; Caines, Helen Louise; Calero Diaz, Liliet; Caliva, Alberto; Calvo Villar, Ernesto; Camerini, Paolo; Carena, Francesco; Carena, Wisla; Carnesecchi, Francesca; Castillo Castellanos, Javier Ernesto; Castro, Andrew John; Casula, Ester Anna Rita; Ceballos Sanchez, Cesar; Cepila, Jan; Cerello, Piergiorgio; Cerkala, Jakub; Chang, Beomsu; Chapeland, Sylvain; Chartier, Marielle; Charvet, Jean-Luc Fernand; Chattopadhyay, Subhasis; Chattopadhyay, Sukalyan; Chauvin, Alex; Chelnokov, Volodymyr; Cherney, Michael Gerard; Cheshkov, Cvetan Valeriev; Cheynis, Brigitte; Chibante Barroso, Vasco Miguel; Dobrigkeit Chinellato, David; Cho, Soyeon; Chochula, Peter; Choi, Kyungeon; Chojnacki, Marek; Choudhury, Subikash; Christakoglou, Panagiotis; Christensen, Christian Holm; Christiansen, Peter; Chujo, Tatsuya; Chung, Suh-Urk; Cicalo, Corrado; Cifarelli, Luisa; Cindolo, Federico; Cleymans, Jean Willy Andre; Colamaria, Fabio Filippo; Colella, Domenico; Collu, Alberto; Colocci, Manuel; Conesa Balbastre, Gustavo; Conesa Del Valle, Zaida; Connors, Megan Elizabeth; Contreras Nuno, Jesus Guillermo; Cormier, Thomas Michael; Corrales Morales, Yasser; Cortes Maldonado, Ismael; Cortese, Pietro; Cosentino, Mauro Rogerio; Costa, Filippo; Crkovska, Jana; Crochet, Philippe; Cruz Albino, Rigoberto; Cuautle Flores, Eleazar; Cunqueiro Mendez, Leticia; Dahms, Torsten; Dainese, Andrea; Danisch, Meike Charlotte; Danu, Andrea; Das, Debasish; Das, Indranil; Das, Supriya; Dash, Ajay Kumar; Dash, Sadhana; De, Sudipan; De Caro, Annalisa; De Cataldo, Giacinto; De Conti, Camila; De Cuveland, Jan; De Falco, Alessandro; De Gruttola, Daniele; De Marco, Nora; De Pasquale, Salvatore; Derradi De Souza, Rafael; Deisting, Alexander; Deloff, Andrzej; Denes, Ervin Sandor; Deplano, Caterina; Dhankher, Preeti; Di Bari, Domenico; Di Mauro, Antonio; Di Nezza, Pasquale; Di Ruzza, Benedetto; Diaz Corchero, Miguel Angel; Dietel, Thomas; Dillenseger, Pascal; Divia, Roberto; Djuvsland, Oeystein; Dobrin, Alexandru Florin; Domenicis Gimenez, Diogenes; Donigus, Benjamin; Dordic, Olja; Drozhzhova, Tatiana; Dubey, Anand Kumar; Dubla, Andrea; Ducroux, Laurent; Dupieux, Pascal; Ehlers Iii, Raymond James; Elia, Domenico; Endress, Eric; Engel, Heiko; Epple, Eliane; Erazmus, Barbara Ewa; Erdemir, Irem; Erhardt, Filip; Espagnon, Bruno; Estienne, Magali Danielle; Esumi, Shinichi; Eum, Jongsik; Evans, David; Evdokimov, Sergey; Eyyubova, Gyulnara; Fabbietti, Laura; Fabris, Daniela; Faivre, Julien; Fantoni, Alessandra; Fasel, Markus; Feldkamp, Linus; Feliciello, Alessandro; Feofilov, Grigorii; Ferencei, Jozef; Fernandez Tellez, Arturo; Gonzalez Ferreiro, Elena; Ferretti, Alessandro; Festanti, Andrea; Feuillard, Victor Jose Gaston; Figiel, Jan; Araujo Silva Figueredo, Marcel; Filchagin, Sergey; Finogeev, Dmitry; Fionda, Fiorella; Fiore, Enrichetta Maria; Floris, Michele; Foertsch, Siegfried Valentin; Foka, Panagiota; Fokin, Sergey; Fragiacomo, Enrico; Francescon, Andrea; Francisco, Audrey; Frankenfeld, Ulrich Michael; Fronze, Gabriele Gaetano; Fuchs, Ulrich; Furget, Christophe; Furs, Artur; Fusco Girard, Mario; Gaardhoeje, Jens Joergen; Gagliardi, Martino; Gago Medina, Alberto Martin; Gajdosova, Katarina; Gallio, Mauro; Duarte Galvan, Carlos; Gangadharan, Dhevan Raja; Ganoti, Paraskevi; Gao, Chaosong; Garabatos Cuadrado, Jose; Garcia-Solis, Edmundo Javier; Garg, Kunal; Gargiulo, Corrado; Gasik, Piotr Jan; Gauger, Erin Frances; Germain, Marie; Gheata, Mihaela; Ghosh, Premomoy; Ghosh, Sanjay Kumar; Gianotti, Paola; Giubellino, Paolo; Giubilato, Piero; Gladysz-Dziadus, Ewa; Glassel, Peter; Gomez Coral, Diego Mauricio; Gomez Ramirez, Andres; Sanchez Gonzalez, Andres; Gonzalez, Victor; Gonzalez Zamora, Pedro; Gorbunov, Sergey; Gorlich, Lidia Maria; Gotovac, Sven; Grabski, Varlen; Grachov, Oleg Anatolievich; Graczykowski, Lukasz Kamil; Graham, Katie Leanne; Grelli, Alessandro; Grigoras, Alina Gabriela; Grigoras, Costin; Grigoryev, Vladislav; Grigoryan, Ara; Grigoryan, Smbat; Grynyov, Borys; Grion, Nevio; Gronefeld, Julius Maximilian; Grosse-Oetringhaus, Jan Fiete; Grosso, Raffaele; Gruber, Lukas; Guber, Fedor; Guernane, Rachid; Guerzoni, Barbara; Gulbrandsen, Kristjan Herlache; Gunji, Taku; Gupta, Anik; Gupta, Ramni; Haake, Rudiger; Hadjidakis, Cynthia Marie; Haiduc, Maria; Hamagaki, Hideki; Hamar, Gergoe; Hamon, Julien Charles; Harris, John William; Harton, Austin Vincent; Hatzifotiadou, Despina; Hayashi, Shinichi; Heckel, Stefan Thomas; Hellbar, Ernst; Helstrup, Haavard; Herghelegiu, Andrei Ionut; Herrera Corral, Gerardo Antonio; Herrmann, Florian; Hess, Benjamin Andreas; Hetland, Kristin Fanebust; Hillemanns, Hartmut; Hippolyte, Boris; Horak, David; Hosokawa, Ritsuya; Hristov, Peter Zahariev; Hughes, Charles; Humanic, Thomas; Hussain, Nur; Hussain, Tahir; Hutter, Dirk; Hwang, Dae Sung; Ilkaev, Radiy; Inaba, Motoi; Incani, Elisa; Ippolitov, Mikhail; Irfan, Muhammad; Isakov, Vladimir; Ivanov, Marian; Ivanov, Vladimir; Izucheev, Vladimir; Jacak, Barbara; Jacazio, Nicolo; Jacobs, Peter Martin; Jadhav, Manoj Bhanudas; Jadlovska, Slavka; Jadlovsky, Jan; Jahnke, Cristiane; Jakubowska, Monika Joanna; Janik, Malgorzata Anna; Pahula Hewage, Sandun; Jena, Chitrasen; Jena, Satyajit; Jimenez Bustamante, Raul Tonatiuh; Jones, Peter Graham; Jusko, Anton; Kalinak, Peter; Kalweit, Alexander Philipp; Kang, Ju Hwan; Kaplin, Vladimir; Kar, Somnath; Karasu Uysal, Ayben; Karavichev, Oleg; Karavicheva, Tatiana; Karayan, Lilit; Karpechev, Evgeny; Kebschull, Udo Wolfgang; Keidel, Ralf; Keijdener, Darius Laurens; Keil, Markus; Khan, Mohammed Mohisin; Khan, Palash; Khan, Shuaib Ahmad; Khanzadeev, Alexei; Kharlov, Yury; Khatun, Anisa; Kileng, Bjarte; Kim, Do Won; Kim, Dong Jo; Kim, Daehyeok; Kim, Hyeonjoong; Kim, Jinsook; Kim, Jiyoung; Kim, Minwoo; Kim, Se Yong; Kim, Taesoo; Kirsch, Stefan; Kisel, Ivan; Kiselev, Sergey; Kisiel, Adam Ryszard; Kiss, Gabor; Klay, Jennifer Lynn; Klein, Carsten; Klein, Jochen; Klein-Boesing, Christian; Klewin, Sebastian; Kluge, Alexander; Knichel, Michael Linus; Knospe, Anders Garritt; Kobdaj, Chinorat; Kofarago, Monika; Kollegger, Thorsten; Kolozhvari, Anatoly; Kondratev, Valerii; Kondratyeva, Natalia; Kondratyuk, Evgeny; Konevskikh, Artem; Kopcik, Michal; Kour, Mandeep; Kouzinopoulos, Charalampos; Kovalenko, Oleksandr; Kovalenko, Vladimir; Kowalski, Marek; Koyithatta Meethaleveedu, Greeshma; Kralik, Ivan; Kravcakova, Adela; Krivda, Marian; Krizek, Filip; Kryshen, Evgeny; Krzewicki, Mikolaj; Kubera, Andrew Michael; Kucera, Vit; Kuhn, Christian Claude; Kuijer, Paulus Gerardus; Kumar, Ajay; Kumar, Jitendra; Kumar, Lokesh; Kumar, Shyam; Kurashvili, Podist; Kurepin, Alexander; Kurepin, Alexey; Kuryakin, Alexey; Kweon, Min Jung; Kwon, Youngil; La Pointe, Sarah Louise; La Rocca, Paola; Ladron De Guevara, Pedro; Lagana Fernandes, Caio; Lakomov, Igor; Langoy, Rune; Lapidus, Kirill; Lara Martinez, Camilo Ernesto; Lardeux, Antoine Xavier; Lattuca, Alessandra; Laudi, Elisa; Lea, Ramona; Leardini, Lucia; Lee, Seongjoo; Lehas, Fatiha; Lehner, Sebastian; Lemmon, Roy Crawford; Lenti, Vito; Leogrande, Emilia; Leon Monzon, Ildefonso; Leon Vargas, Hermes; Leoncino, Marco; Levai, Peter; Li, Shuang; Li, Xiaomei; Lien, Jorgen Andre; Lietava, Roman; Lindal, Svein; Lindenstruth, Volker; Lippmann, Christian; Lisa, Michael Annan; Ljunggren, Hans Martin; Lodato, Davide Francesco; Lonne, Per-Ivar; Loginov, Vitaly; Loizides, Constantinos; Lopez, Xavier Bernard; Lopez Torres, Ernesto; Lowe, Andrew John; Luettig, Philipp Johannes; Lunardon, Marcello; Luparello, Grazia; Lupi, Matteo; Lutz, Tyler Harrison; Maevskaya, Alla; Mager, Magnus; Mahajan, Sanjay; Mahmood, Sohail Musa; Maire, Antonin; Majka, Richard Daniel; Malaev, Mikhail; Maldonado Cervantes, Ivonne Alicia; Malinina, Liudmila; Mal'Kevich, Dmitry; Malzacher, Peter; Mamonov, Alexander; Manko, Vladislav; Manso, Franck; Manzari, Vito; Mao, Yaxian; Marchisone, Massimiliano; Mares, Jiri; Margagliotti, Giacomo Vito; Margotti, Anselmo; Margutti, Jacopo; Marin, Ana Maria; Markert, Christina; Marquard, Marco; Martin, Nicole Alice; Martinengo, Paolo; Martinez Hernandez, Mario Ivan; Martinez-Garcia, Gines; Martinez Pedreira, Miguel; Mas, Alexis Jean-Michel; Masciocchi, Silvia; Masera, Massimo; Masoni, Alberto; Mastroserio, Annalisa; Matyja, Adam Tomasz; Mayer, Christoph; Mazer, Joel Anthony; Mazzilli, Marianna; Mazzoni, Alessandra Maria; Mcdonald, Daniel; Meddi, Franco; Melikyan, Yuri; Menchaca-Rocha, Arturo Alejandro; Meninno, Elisa; Mercado-Perez, Jorge; Meres, Michal; Mhlanga, Sibaliso; Miake, Yasuo; Mieskolainen, Matti Mikael; Mikhaylov, Konstantin; Milano, Leonardo; Milosevic, Jovan; Mischke, Andre; Mishra, Aditya Nath; Mishra, Tribeni; Miskowiec, Dariusz Czeslaw; Mitra, Jubin; Mitu, Ciprian Mihai; Mohammadi, Naghmeh; Mohanty, Bedangadas; Molnar, Levente; Montano Zetina, Luis Manuel; Montes Prado, Esther; Moreira De Godoy, Denise Aparecida; Perez Moreno, Luis Alberto; Moretto, Sandra; Morreale, Astrid; Morsch, Andreas; Muccifora, Valeria; Mudnic, Eugen; Muhlheim, Daniel Michael; Muhuri, Sanjib; Mukherjee, Maitreyee; Mulligan, James Declan; Gameiro Munhoz, Marcelo; Munning, Konstantin; Munzer, Robert Helmut; Murakami, Hikari; Murray, Sean; Musa, Luciano; Musinsky, Jan; Naik, Bharati; Nair, Rahul; Nandi, Basanta Kumar; Nania, Rosario; Nappi, Eugenio; Naru, Muhammad Umair; Ferreira Natal Da Luz, Pedro Hugo; Nattrass, Christine; Rosado Navarro, Sebastian; Nayak, Kishora; Nayak, Ranjit; Nayak, Tapan Kumar; Nazarenko, Sergey; Nedosekin, Alexander; Negrao De Oliveira, Renato Aparecido; Nellen, Lukas; Ng, Fabian; Nicassio, Maria; Niculescu, Mihai; Niedziela, Jeremi; Nielsen, Borge Svane; Nikolaev, Sergey; Nikulin, Sergey; Nikulin, Vladimir; Noferini, Francesco; Nomokonov, Petr; Nooren, Gerardus; Cabanillas Noris, Juan Carlos; Norman, Jaime; Nyanin, Alexander; Nystrand, Joakim Ingemar; Oeschler, Helmut Oskar; Oh, Saehanseul; Oh, Sun Kun; Ohlson, Alice Elisabeth; Okatan, Ali; Okubo, Tsubasa; Oleniacz, Janusz; Oliveira Da Silva, Antonio Carlos; Oliver, Michael Henry; Onderwaater, Jacobus; Oppedisano, Chiara; Orava, Risto; Oravec, Matej; Ortiz Velasquez, Antonio; Oskarsson, Anders Nils Erik; Otwinowski, Jacek Tomasz; Oyama, Ken; Ozdemir, Mahmut; Pachmayer, Yvonne Chiara; Pagano, Davide; Pagano, Paola; Paic, Guy; Pal, Susanta Kumar; Palni, Prabhakar; Pan, Jinjin; Pandey, Ashutosh Kumar; Papikyan, Vardanush; Pappalardo, Giuseppe; Pareek, Pooja; Park, Woojin; Parmar, Sonia; Passfeld, Annika; Paticchio, Vincenzo; Patra, Rajendra Nath; Paul, Biswarup; Pei, Hua; Peitzmann, Thomas; Peng, Xinye; Pereira Da Costa, Hugo Denis Antonio; Peresunko, Dmitry Yurevich; Perez Lezama, Edgar; Peskov, Vladimir; Pestov, Yury; Petracek, Vojtech; Petrov, Viacheslav; Petrovici, Mihai; Petta, Catia; Piano, Stefano; Pikna, Miroslav; Pillot, Philippe; Ozelin De Lima Pimentel, Lais; Pinazza, Ombretta; Pinsky, Lawrence; Piyarathna, Danthasinghe; Ploskon, Mateusz Andrzej; Planinic, Mirko; Pluta, Jan Marian; Pochybova, Sona; Podesta Lerma, Pedro Luis Manuel; Poghosyan, Martin; Polishchuk, Boris; Poljak, Nikola; Poonsawat, Wanchaloem; Pop, Amalia; Poppenborg, Hendrik; Porteboeuf, Sarah Julie; Porter, R Jefferson; Pospisil, Jan; Prasad, Sidharth Kumar; Preghenella, Roberto; Prino, Francesco; Pruneau, Claude Andre; Pshenichnov, Igor; Puccio, Maximiliano; Puddu, Giovanna; Pujahari, Prabhat Ranjan; Punin, Valery; Putschke, Jorn Henning; Qvigstad, Henrik; Rachevski, Alexandre; Raha, Sibaji; Rajput, Sonia; Rak, Jan; Rakotozafindrabe, Andry Malala; Ramello, Luciano; Rami, Fouad; Raniwala, Rashmi; Raniwala, Sudhir; Rasanen, Sami Sakari; Rascanu, Bogdan Theodor; Rathee, Deepika; Ravasenga, Ivan; Read, Kenneth Francis; Redlich, Krzysztof; Reed, Rosi Jan; Rehman, Attiq Ur; Reichelt, Patrick Simon; Reidt, Felix; Ren, Xiaowen; Renfordt, Rainer Arno Ernst; Reolon, Anna Rita; Reshetin, Andrey; Reygers, Klaus Johannes; Riabov, Viktor; Ricci, Renato Angelo; Richert, Tuva Ora Herenui; Richter, Matthias Rudolph; Riedler, Petra; Riegler, Werner; Riggi, Francesco; Ristea, Catalin-Lucian; Rodriguez Cahuantzi, Mario; Rodriguez Manso, Alis; Roeed, Ketil; Rogochaya, Elena; Rohr, David Michael; Roehrich, Dieter; Ronchetti, Federico; Ronflette, Lucile; Rosnet, Philippe; Rossi, Andrea; Roukoutakis, Filimon; Roy, Ankhi; Roy, Christelle Sophie; Roy, Pradip Kumar; Rubio Montero, Antonio Juan; Rui, Rinaldo; Russo, Riccardo; Ryabinkin, Evgeny; Ryabov, Yury; Rybicki, Andrzej; Saarinen, Sampo; Sadhu, Samrangy; Sadovskiy, Sergey; Safarik, Karel; Sahlmuller, Baldo; Sahoo, Pragati; Sahoo, Raghunath; Sahoo, Sarita; Sahu, Pradip Kumar; Saini, Jogender; Sakai, Shingo; Saleh, Mohammad Ahmad; Salzwedel, Jai Samuel Nielsen; Sambyal, Sanjeev Singh; Samsonov, Vladimir; Sandor, Ladislav; Sandoval, Andres; Sano, Masato; Sarkar, Debojit; Sarkar, Nachiketa; Sarma, Pranjal; Scapparone, Eugenio; Scarlassara, Fernando; Schiaua, Claudiu Cornel; Schicker, Rainer Martin; Schmidt, Christian Joachim; Schmidt, Hans Rudolf; Schmidt, Martin; Schuchmann, Simone; Schukraft, Jurgen; Schutz, Yves Roland; Schwarz, Kilian Eberhard; Schweda, Kai Oliver; Scioli, Gilda; Scomparin, Enrico; Scott, Rebecca Michelle; Sefcik, Michal; Seger, Janet Elizabeth; Sekiguchi, Yuko; Sekihata, Daiki; Selyuzhenkov, Ilya; Senosi, Kgotlaesele; Senyukov, Serhiy; Serradilla Rodriguez, Eulogio; Sevcenco, Adrian; Shabanov, Arseniy; Shabetai, Alexandre; Shadura, Oksana; Shahoyan, Ruben; Shangaraev, Artem; Sharma, Ankita; Sharma, Mona; Sharma, Monika; Sharma, Natasha; Sheikh, Ashik Ikbal; Shigaki, Kenta; Shou, Qiye; Shtejer Diaz, Katherin; Sibiryak, Yury; Siddhanta, Sabyasachi; Sielewicz, Krzysztof Marek; Siemiarczuk, Teodor; Silvermyr, David Olle Rickard; Silvestre, Catherine Micaela; Simatovic, Goran; Simonetti, Giuseppe; Singaraju, Rama Narayana; Singh, Ranbir; Singhal, Vikas; Sarkar - Sinha, Tinku; Sitar, Branislav; Sitta, Mario; Skaali, Bernhard; Slupecki, Maciej; Smirnov, Nikolai; Snellings, Raimond; Snellman, Tomas Wilhelm; Song, Jihye; Song, Myunggeun; Song, Zixuan; Soramel, Francesca; Sorensen, Soren Pontoppidan; Sozzi, Federica; Spiriti, Eleuterio; Sputowska, Iwona Anna; Spyropoulou-Stassinaki, Martha; Stachel, Johanna; Stan, Ionel; Stankus, Paul; Stenlund, Evert Anders; Steyn, Gideon Francois; Stiller, Johannes Hendrik; Stocco, Diego; Strmen, Peter; Alarcon Do Passo Suaide, Alexandre; Sugitate, Toru; Suire, Christophe Pierre; Suleymanov, Mais Kazim Oglu; Suljic, Miljenko; Sultanov, Rishat; Sumbera, Michal; Sumowidagdo, Suharyo; Swain, Sagarika; Szabo, Alexander; Szarka, Imrich; Szczepankiewicz, Adam; Szymanski, Maciej Pawel; Tabassam, Uzma; Takahashi, Jun; Tambave, Ganesh Jagannath; Tanaka, Naoto; Tarhini, Mohamad; Tariq, Mohammad; Tarzila, Madalina-Gabriela; Tauro, Arturo; Tejeda Munoz, Guillermo; Telesca, Adriana; Terasaki, Kohei; Terrevoli, Cristina; Teyssier, Boris; Thaeder, Jochen Mathias; Thakur, Dhananjaya; Thomas, Deepa; Tieulent, Raphael Noel; Tikhonov, Anatoly; Timmins, Anthony Robert; Toia, Alberica; Trogolo, Stefano; Trombetta, Giuseppe; Trubnikov, Victor; Trzaska, Wladyslaw Henryk; Tsuji, Tomoya; Tumkin, Alexandr; Turrisi, Rosario; Tveter, Trine Spedstad; Ullaland, Kjetil; Uras, Antonio; Usai, Gianluca; Utrobicic, Antonija; Vala, Martin; Valencia Palomo, Lizardo; Van Der Maarel, Jasper; Van Hoorne, Jacobus Willem; Van Leeuwen, Marco; Vanat, Tomas; Vande Vyvre, Pierre; Varga, Dezso; Diozcora Vargas Trevino, Aurora; Vargyas, Marton; Varma, Raghava; Vasileiou, Maria; Vasiliev, Andrey; Vauthier, Astrid; Vazquez Doce, Oton; Vechernin, Vladimir; Veen, Annelies Marianne; Velure, Arild; Vercellin, Ermanno; Vergara Limon, Sergio; Vernet, Renaud; Vickovic, Linda; Viinikainen, Jussi Samuli; Vilakazi, Zabulon; Villalobos Baillie, Orlando; Villatoro Tello, Abraham; Vinogradov, Alexander; Vinogradov, Leonid; Virgili, Tiziano; Vislavicius, Vytautas; Viyogi, Yogendra; Vodopyanov, Alexander; Volkl, Martin Andreas; Voloshin, Kirill; Voloshin, Sergey; Volpe, Giacomo; Von Haller, Barthelemy; Vorobyev, Ivan; Vranic, Danilo; Vrlakova, Janka; Vulpescu, Bogdan; Wagner, Boris; Wagner, Jan; Wang, Hongkai; Wang, Mengliang; Watanabe, Daisuke; Watanabe, Yosuke; Weber, Michael; Weber, Steffen Georg; Weiser, Dennis Franz; Wessels, Johannes Peter; Westerhoff, Uwe; Whitehead, Andile Mothegi; Wiechula, Jens; Wikne, Jon; Wilk, Grzegorz Andrzej; Wilkinson, Jeremy John; Willems, Guido Alexander; Williams, Crispin; Windelband, Bernd Stefan; Winn, Michael Andreas; Yalcin, Serpil; Yang, Ping; Yano, Satoshi; Yin, Zhongbao; Yokoyama, Hiroki; Yoo, In-Kwon; Yoon, Jin Hee; Yurchenko, Volodymyr; Zaborowska, Anna; Zaccolo, Valentina; Zaman, Ali; Zampolli, Chiara; Correia Zanoli, Henrique Jose; Zaporozhets, Sergey; Zardoshti, Nima; Zarochentsev, Andrey; Zavada, Petr; Zavyalov, Nikolay; Zbroszczyk, Hanna Paulina; Zgura, Sorin Ion; Zhalov, Mikhail; Zhang, Haitao; Zhang, Xiaoming; Zhang, Yonghong; Chunhui, Zhang; Zhang, Zuman; Zhao, Chengxin; Zhigareva, Natalia; Zhou, Daicui; Zhou, You; Zhou, Zhuo; Zhu, Hongsheng; Zhu, Jianhui; Zichichi, Antonino; Zimmermann, Alice; Zimmermann, Markus Bernhard; Zinovjev, Gennady; Zyzak, Maksym

    2017-01-01

    At sufficiently high temperature and energy density, nuclear matter undergoes a transition to a phase in which quarks and gluons are not confined: the quark–gluon plasma (QGP). Such an exotic state of strongly interacting quantum chromodynamics matter is produced in the laboratory in heavy nuclei high-energy collisions, where an enhanced production of strange hadrons is observed. Strangeness enhancement, originally proposed as a signature of QGP formation in nuclear collisions, is more pronounced for multi-strange baryons. Several effects typical of heavy-ion phenomenology have been observed in high-multiplicity proton–proton (pp) collisions, but the enhanced production of multi-strange particles has not been reported so far. Here we present the first observation of strangeness enhancement in high-multiplicity proton–proton collisions. We find that the integrated yields of strange and multi-strange particles, relative to pions, increases significantly with the event charged-particle multiplicity. The me...

  17. Towards a decision support system for control of multiple food safety hazards in raw milk production

    Spiegel, van der M.; Sterrenburg, P.; Haasnoot, W.; Fels-Klerx, van der H.J.

    2013-01-01

    Decision support systems (DSS) for controlling multiple food safety hazards in raw milk production have not yet been developed, but the underlying components are fragmentarily available. This article presents the state-of-the-art of essential DSS elements for judging food safety compliance of raw

  18. Serum uric acid levels and leukocyte nitric oxide production in multiple sclerosis patients outside relapses

    Mostert, JP; Ramsaransing, GSM; Heerserna, DJ; Heerings, M; Wilczak, N; De Keyser, J

    2005-01-01

    Background: A number of studies found that patients with multiple sclerosis (MS) have low serum levels of uric acid. It is unclear whether this represents a primary deficit or secondary effect. Uric acid is a scavenger of peroxynitrite, which is the product of nitric oxide (NO) and superoxide.

  19. Radioactive sources production in the Boris Kidric Institute of nuclear sciences

    Radosavljevic, B.; Nemoda, Dj.; Memedovic, T.; Bircanin, LJ.

    1978-01-01

    Since 1960, in the Laboratory for radioisotopes production of the Institute isotopes were produced for industrial, medical and research purposes. From the beginning, this activity was developed in two directions: 1. sealed sources, for industrial radiography, teletherapy Cobalt, later for lightning arresters, level meters, densitometers etc., 2. radioactive sources that need chemical treatment for different applications in industry and research. This paper lists the types of radioactive sources and methods for production [sr

  20. The effect of different nutrient sources on biomass production of ...

    The effect of various organic, inorganic and complex compounds on the biomass production (mycelial dry weight) of Lepiota procera, a Nigerian edible higher fungus was investigated. Among the seventeen carbon compounds tested, mannose enhanced the best biomass yield. This was followed in order by glucose, ...

  1. Towards sustainable fish feed production using novel protein sources

    Draganovic, V.

    2013-01-01

    The consumption of fish and fish-related products is increasing. Due to improved welfare and suggested health benefits, consumers are now eating more fish. In 2008, global fisheries supplied the world with about 142 million tons of fish, of which 115 million tons was used as human food, which is

  2. Open Source Development of Tangible Products - from a business perspective

    Fjeldsted, Asta S.; Adalsteinsdottir, Gudrun; Howard, Thomas J.

    definition for OSD is proposed and used to describe the key elements of a suggested OSD Process model. Several case studies are analysed to create an Archetypal Business Model characterising OSD of tangible products and the possibilities and delimitations within. Furthermore, strategic tools are suggested...... utilise this new approach to improve their business models and capture value in innovative ways....

  3. Characterization of cellulase production by carbon sources in two ...

    user7

    2013-11-27

    Nov 27, 2013 ... 7State Key Laboratory of Urban Water Resource and Environment, ... acted on these inducers, analysis of reaction products by high performance liquid chromatography. (HPLC) revealed that cell wall/envelope enzyme and endoenzyme from two ... specific activity are major factors in preventing application.

  4. [Multiple time scales analysis of spatial differentiation characteristics of non-point source nitrogen loss within watershed].

    Liu, Mei-bing; Chen, Xing-wei; Chen, Ying

    2015-07-01

    Identification of the critical source areas of non-point source pollution is an important means to control the non-point source pollution within the watershed. In order to further reveal the impact of multiple time scales on the spatial differentiation characteristics of non-point source nitrogen loss, a SWAT model of Shanmei Reservoir watershed was developed. Based on the simulation of total nitrogen (TN) loss intensity of all 38 subbasins, spatial distribution characteristics of nitrogen loss and critical source areas were analyzed at three time scales of yearly average, monthly average and rainstorms flood process, respectively. Furthermore, multiple linear correlation analysis was conducted to analyze the contribution of natural environment and anthropogenic disturbance on nitrogen loss. The results showed that there were significant spatial differences of TN loss in Shanmei Reservoir watershed at different time scales, and the spatial differentiation degree of nitrogen loss was in the order of monthly average > yearly average > rainstorms flood process. TN loss load mainly came from upland Taoxi subbasin, which was identified as the critical source area. At different time scales, land use types (such as farmland and forest) were always the dominant factor affecting the spatial distribution of nitrogen loss, while the effect of precipitation and runoff on the nitrogen loss was only taken in no fertilization month and several processes of storm flood at no fertilization date. This was mainly due to the significant spatial variation of land use and fertilization, as well as the low spatial variability of precipitation and runoff.

  5. PORTFOLIO MANAGEMENT IN NEW PRODUCTS DEVELOPMENT IN THE TELECOMMUNICATION SECTOR IN BRAZIL: A MULTIPLE CASES STUDY

    Roque Rabechini Jr.

    2017-06-01

    Full Text Available This study aimed to understand how the use of portfolio management practices influence the development of new products in the Brazilian telecommunications operators. The chosen alternative methodology was the multiple case study. The results showed that the processes of identification, selection and prioritization projects influence the development of new products. Specifically, we found that the optimization of resources and product launch projects in short periods of time, are indicators to reveal the possibilities of organizations to remain competitive in the market.

  6. Carbon sequestration in wood products: a method for attribution to multiple parties

    Tonn, Bruce; Marland, Gregg

    2007-01-01

    When forest is harvested some of the forest carbon ends up in wood products. If the forest is managed so that the standing stock of the forest remains constant over time, and the stock of wood products is increasing, then carbon dioxide is being removed from the atmosphere in net and this should be reflected in accounting for greenhouse gas emissions. We suggest that carbon sequestration in wood products requires cooperation of multiple parties; from the forest owner to the product manufacturer to the product user, and perhaps others. Credit for sequestering carbon away from the atmosphere could acknowledge the contributions of these multiple parties. Accounting under a cap-and-trade or tax system is not necessarily an inventory system, it is a system designed to motivate and/or reward an environmental objective. We describe a system of attribution whereby credits for carbon sequestration would be shared among multiple, contributing parties. It is hoped that the methodology outlined herein proves attractive enough to parties concerned to spur them to address the details of such a system. The system of incentives one would choose for limiting or controlling greenhouse gas emissions could be quite different, depending on how the attribution for emissions and sequestration is chosen

  7. Energy harvesting: small scale energy production from ambient sources

    Yeatman, Eric M.

    2009-03-01

    Energy harvesting - the collection of otherwise unexploited energy in the local environment - is attracting increasing attention for the powering of electronic devices. While the power levels that can be reached are typically modest (microwatts to milliwatts), the key motivation is to avoid the need for battery replacement or recharging in portable or inaccessible devices. Wireless sensor networks are a particularly important application: the availability of essentially maintenance free sensor nodes, as enabled by energy harvesting, will greatly increase the feasibility of large scale networks, in the paradigm often known as pervasive sensing. Such pervasive sensing networks, used to monitor buildings, structures, outdoor environments or the human body, offer significant benefits for large scale energy efficiency, health and safety, and many other areas. Sources of energy for harvesting include light, temperature differences, and ambient motion, and a wide range of miniature energy harvesters based on these sources have been proposed or demonstrated. This paper reviews the principles and practice in miniature energy harvesters, and discusses trends, suitable applications, and possible future developments.

  8. Determination of Key Risk Supervision Areas around River-Type Water Sources Affected by Multiple Risk Sources: A Case Study of Water Sources along the Yangtze’s Nanjing Section

    Qi Zhou

    2017-02-01

    Full Text Available To provide a reference for risk management of water sources, this study screens the key risk supervision areas around river-type water sources (hereinafter referred to as the water sources threatened by multiple fixed risk sources (the risk sources, and establishes a comprehensive methodological system. Specifically, it comprises: (1 method of partitioning risk source concentrated sub-regions for screening water source perimeter key risk supervision areas; (2 approach of determining sub-regional risk indexes (SrRI, which characterizes the scale of sub-regional risks considering factors like risk distribution intensity within sub-regions, risk indexes of risk sources (RIRS, characterizing the risk scale of risk sources and the number of risk sources; and (3 method of calculating sub-region’s risk threats to the water sources (SrTWS which considers the positional relationship between water sources and sub-regions as well as SrRI, and the criteria for determining key supervision sub-regions. Favorable effects are achieved by applying this methodological system in determining water source perimeter sub-regions distributed along the Yangtze’s Nanjing section. Results revealed that for water sources, the key sub-regions needing supervision were SD16, SD06, SD21, SD26, SD15, SD03, SD02, SD32, SD10, SD11, SD14, SD05, SD27, etc., in the order of criticality. The sub-region with the greatest risk threats on the water sources was SD16, which was located in the middle reaches of Yangtze River. In general, sub-regions along the upper Yangtze reaches had greater threats to water sources than the lower reach sub-regions other than SD26 and SD21. Upstream water sources were less subject to the threats of sub-regions than the downstream sources other than NJ09B and NJ03.

  9. Real-Time Localization of Moving Dipole Sources for Tracking Multiple Free-Swimming Weakly Electric Fish

    Jun, James Jaeyoon; Longtin, André; Maler, Leonard

    2013-01-01

    In order to survive, animals must quickly and accurately locate prey, predators, and conspecifics using the signals they generate. The signal source location can be estimated using multiple detectors and the inverse relationship between the received signal intensity (RSI) and the distance, but difficulty of the source localization increases if there is an additional dependence on the orientation of a signal source. In such cases, the signal source could be approximated as an ideal dipole for simplification. Based on a theoretical model, the RSI can be directly predicted from a known dipole location; but estimating a dipole location from RSIs has no direct analytical solution. Here, we propose an efficient solution to the dipole localization problem by using a lookup table (LUT) to store RSIs predicted by our theoretically derived dipole model at many possible dipole positions and orientations. For a given set of RSIs measured at multiple detectors, our algorithm found a dipole location having the closest matching normalized RSIs from the LUT, and further refined the location at higher resolution. Studying the natural behavior of weakly electric fish (WEF) requires efficiently computing their location and the temporal pattern of their electric signals over extended periods. Our dipole localization method was successfully applied to track single or multiple freely swimming WEF in shallow water in real-time, as each fish could be closely approximated by an ideal current dipole in two dimensions. Our optimized search algorithm found the animal’s positions, orientations, and tail-bending angles quickly and accurately under various conditions, without the need for calibrating individual-specific parameters. Our dipole localization method is directly applicable to studying the role of active sensing during spatial navigation, or social interactions between multiple WEF. Furthermore, our method could be extended to other application areas involving dipole source

  10. Real-Time Localization of Moving Dipole Sources for Tracking Multiple Free-Swimming Weakly Electric Fish.

    James Jaeyoon Jun

    Full Text Available In order to survive, animals must quickly and accurately locate prey, predators, and conspecifics using the signals they generate. The signal source location can be estimated using multiple detectors and the inverse relationship between the received signal intensity (RSI and the distance, but difficulty of the source localization increases if there is an additional dependence on the orientation of a signal source. In such cases, the signal source could be approximated as an ideal dipole for simplification. Based on a theoretical model, the RSI can be directly predicted from a known dipole location; but estimating a dipole location from RSIs has no direct analytical solution. Here, we propose an efficient solution to the dipole localization problem by using a lookup table (LUT to store RSIs predicted by our theoretically derived dipole model at many possible dipole positions and orientations. For a given set of RSIs measured at multiple detectors, our algorithm found a dipole location having the closest matching normalized RSIs from the LUT, and further refined the location at higher resolution. Studying the natural behavior of weakly electric fish (WEF requires efficiently computing their location and the temporal pattern of their electric signals over extended periods. Our dipole localization method was successfully applied to track single or multiple freely swimming WEF in shallow water in real-time, as each fish could be closely approximated by an ideal current dipole in two dimensions. Our optimized search algorithm found the animal's positions, orientations, and tail-bending angles quickly and accurately under various conditions, without the need for calibrating individual-specific parameters. Our dipole localization method is directly applicable to studying the role of active sensing during spatial navigation, or social interactions between multiple WEF. Furthermore, our method could be extended to other application areas involving dipole

  11. Estimation of Multiple Point Sources for Linear Fractional Order Systems Using Modulating Functions

    Belkhatir, Zehor; Laleg-Kirati, Taous-Meriem

    2017-01-01

    This paper proposes an estimation algorithm for the characterization of multiple point inputs for linear fractional order systems. First, using polynomial modulating functions method and a suitable change of variables the problem of estimating

  12. Exopolysaccharides enriched in rare sugars: bacterial sources, production, and applications

    Roca, Christophe; Alves, Vitor D.; Freitas, Filomena; Reis, Maria A. M.

    2015-01-01

    The authors acknowledge Fundacao para a Ciencia e Tecnologia (FC&T), Portugal, through projects PEst-C/EQB/LA0006/2013 and PTDC/AGR-ALI/114706/2009 - "New edible bioactive coatings for the improvement of food products quality." FF acknowledges FCT&T for Post-Doctoral fellowship SFRH/BPD/72280/2010. Microbial extracellular polysaccharides (EPS), produced by a wide range of bacteria, are high molecular weight biopolymers, presenting an extreme diversity in terms of chemical structure and com...

  13. Laccase: microbial sources, production, purification, and potential biotechnological applications.

    Shraddha; Shekher, Ravi; Sehgal, Simran; Kamthania, Mohit; Kumar, Ajay

    2011-01-01

    Laccase belongs to the blue multicopper oxidases and participates in cross-linking of monomers, degradation of polymers, and ring cleavage of aromatic compounds. It is widely distributed in higher plants and fungi. It is present in Ascomycetes, Deuteromycetes and Basidiomycetes and abundant in lignin-degrading white-rot fungi. It is also used in the synthesis of organic substance, where typical substrates are amines and phenols, the reaction products are dimers and oligomers derived from the coupling of reactive radical intermediates. In the recent years, these enzymes have gained application in the field of textile, pulp and paper, and food industry. Recently, it is also used in the design of biosensors, biofuel cells, as a medical diagnostics tool and bioremediation agent to clean up herbicides, pesticides and certain explosives in soil. Laccases have received attention of researchers in the last few decades due to their ability to oxidize both phenolic and nonphenolic lignin-related compounds as well as highly recalcitrant environmental pollutants. It has been identified as the principal enzyme associated with cuticular hardening in insects. Two main forms have been found: laccase-1 and laccase-2. This paper reviews the occurrence, mode of action, general properties, production, applications, and immobilization of laccases within different industrial fields.

  14. Microalga Scenedesmus obliquus as a potential source for biodiesel production

    Mandal, Shovon; Mallick, Nirupama [Indian Inst. of Technology, Kharagpur, West Bengal (India). Agricultural and Food Engineering Dept.

    2009-08-15

    Biodiesel from microalgae seems to be the only renewable biofuel that has the potential to completely replace the petroleum-derived transport fuels. Therefore, improving lipid content of microalgal strains could be a cost-effective second generation feedstock for biodiesel production. Lipid accumulation in Scenedesmus obliquus was studied under various culture conditions. The most significant increase in lipid reached 43% of dry cell weight (dcw), which was recorded under N-deficiency (against 12.7% under control condition). Under P-deficiency and thiosulphate supplementation the lipid content also increased up to 30% (dcw). Application of response surface methodology in combination with central composite rotary design (CCRD) resulted in a lipid yield of 61.3% (against 58.3% obtained experimentally) at 0.04, 0.03, and 1.0 g l{sup -1} of nitrate, phosphate, and sodium thiosulphate, respectively for time culture of 8 days. Scenedesmus cells pre-grown in glucose (1.5%)-supplemented N 11 medium when subjected to the above optimized condition, the lipid accumulation was boosted up to 2.16 g l{sup -1}, the value {proportional_to}40-fold higher with respect to the control condition. The presence of palmitate and oleate as the major constituents makes S. obliquus biomass a suitable feedstock for biodiesel production. (orig.)

  15. Energy sources consumption: end uses, efficiency and productivity

    Martin, J.M.

    2005-01-01

    This document analyzes the impact of the choices made by all actors, from the energy producers to the process and infrastructure designers and the end users, in the evolution of energy consumptions. Some very little improvements made in the energy efficiency of appliances can become equivalent to the production of several oil fields or power plants at the world scale. More efficient energy uses will not replace the additional productions but they must be considered together to be compared. The energy files are first analyzed as a whole in order to show the hidden field of energy choices. In this framework, users, designers and fitters have to face very different choices because they consider efficiency improvements under different aspects: scientifical, technical, economical and social (public information and habits). These differences in efficiency uses have a time and spatial impact on the growth of energy consumption. The economical and social factors influence the collective way to consume energy and are expressed by the energy intensity of the economic activity. The last part of this document analyzes the influence of this notion on the world energy consumption scenarios at the 2050 prospects. (J.S.)

  16. Laccase: Microbial Sources, Production, Purification, and Potential Biotechnological Applications

    Shraddha

    2011-01-01

    Full Text Available Laccase belongs to the blue multicopper oxidases and participates in cross-linking of monomers, degradation of polymers, and ring cleavage of aromatic compounds. It is widely distributed in higher plants and fungi. It is present in Ascomycetes, Deuteromycetes and Basidiomycetes and abundant in lignin-degrading white-rot fungi. It is also used in the synthesis of organic substance, where typical substrates are amines and phenols, the reaction products are dimers and oligomers derived from the coupling of reactive radical intermediates. In the recent years, these enzymes have gained application in the field of textile, pulp and paper, and food industry. Recently, it is also used in the design of biosensors, biofuel cells, as a medical diagnostics tool and bioremediation agent to clean up herbicides, pesticides and certain explosives in soil. Laccases have received attention of researchers in the last few decades due to their ability to oxidize both phenolic and nonphenolic lignin-related compounds as well as highly recalcitrant environmental pollutants. It has been identified as the principal enzyme associated with cuticular hardening in insects. Two main forms have been found: laccase-1 and laccase-2. This paper reviews the occurrence, mode of action, general properties, production, applications, and immobilization of laccases within different industrial fields.

  17. New development of laser ion source for highly charged ion beam production at Institute of Modern Physics (invited).

    Zhao, H Y; Zhang, J J; Jin, Q Y; Liu, W; Wang, G C; Sun, L T; Zhang, X Z; Zhao, H W

    2016-02-01

    A laser ion source based on Nd:YAG laser has been being studied at the Institute of Modern Physics for the production of high intensity high charge state heavy ion beams in the past ten years, for possible applications both in a future accelerator complex and in heavy ion cancer therapy facilities. Based on the previous results for the production of multiple-charged ions from a wide range of heavy elements with a 3 J/8 ns Nd:YAG laser [Zhao et al., Rev. Sci. Instrum. 85, 02B910 (2014)], higher laser energy and intensity in the focal spot are necessary for the production of highly charged ions from the elements heavier than aluminum. Therefore, the laser ion source was upgraded with a new Nd:YAG laser, the maximum energy of which is 8 J and the pulse duration can be adjusted from 8 to 18 ns. Since then, the charge state distributions of ions from various elements generated by the 8 J Nd:YAG laser were investigated for different experimental conditions, such as laser energy, pulse duration, power density in the focal spot, and incidence angle. It was shown that the incidence angle is one of the most important parameters for the production of highly charged ions. The capability of producing highly charged ions from the elements lighter than silver was demonstrated with the incidence angle of 10° and laser power density of 8 × 10(13) W cm(-2) in the focal spot, which makes a laser ion source complementary to the superconducting electron cyclotron resonance ion source for the future accelerator complex especially in terms of the ion beam production from some refractory elements. Nevertheless, great efforts with regard to the extraction of intense ion beams, modification of the ion beam pulse duration, and reliability of the ion source still need to be made for practical applications.

  18. The Hidden Health and Economic Burden of Rotavirus Gastroenteritis in Malaysia: An Estimation Using Multiple Data Sources.

    Loganathan, Tharani; Ng, Chiu-Wan; Lee, Way-Seah; Jit, Mark

    2016-06-01

    Rotavirus gastroenteritis (RVGE) results in substantial mortality and morbidity worldwide. However, an accurate estimation of the health and economic burden of RVGE in Malaysia covering public, private and home treatment is lacking. Data from multiple sources were used to estimate diarrheal mortality and morbidity according to health service utilization. The proportion of this burden attributable to rotavirus was estimated from a community-based study and a meta-analysis we conducted of primary hospital-based studies. Rotavirus incidence was determined by multiplying acute gastroenteritis incidence with estimates of the proportion of gastroenteritis attributable to rotavirus. The economic burden of rotavirus disease was estimated from the health systems and societal perspective. Annually, rotavirus results in 27 deaths, 31,000 hospitalizations, 41,000 outpatient visits and 145,000 episodes of home-treated gastroenteritis in Malaysia. We estimate an annual rotavirus incidence of 1 death per 100,000 children and 12 hospitalizations, 16 outpatient clinic visits and 57 home-treated episodes per 1000 children under-5 years. Annually, RVGE is estimated to cost US$ 34 million to the healthcare provider and US$ 50 million to society. Productivity loss contributes almost a third of costs to society. Publicly, privately and home-treated episodes consist of 52%, 27% and 21%, respectively, of the total societal costs. RVGE represents a considerable health and economic burden in Malaysia. Much of the burden lies in privately or home-treated episodes and is poorly captured in previous studies. This study provides vital information for future evaluation of cost-effectiveness, which are necessary for policy-making regarding universal vaccination.

  19. Source term determination from subcritical multiplication measurements at Koral-1 reactor

    Blazquez, J.B.; Barrado, J.M.

    1978-01-01

    By using an AmBe neutron source two independent procedures have been settled for the zero-power experimental fast-reactor Coral-1 in order to measure the source term which appears in the point kinetical equations. In the first one, the source term is measured when the reactor is just critical with source by taking advantage of the wide range of the linear approach to critical for Coral-1. In the second one, the measurement is made in subcritical state by making use of the previous calibrated control rods. Several applications are also included such as the measurement of the detector dead time, the determinations of the reactivity of small samples and the shape of the neutron importance of the source. (author)

  20. Separation of Correlated Astrophysical Sources Using Multiple-Lag Data Covariance Matrices

    Baccigalupi C

    2005-01-01

    Full Text Available This paper proposes a new strategy to separate astrophysical sources that are mutually correlated. This strategy is based on second-order statistics and exploits prior information about the possible structure of the mixing matrix. Unlike ICA blind separation approaches, where the sources are assumed mutually independent and no prior knowledge is assumed about the mixing matrix, our strategy allows the independence assumption to be relaxed and performs the separation of even significantly correlated sources. Besides the mixing matrix, our strategy is also capable to evaluate the source covariance functions at several lags. Moreover, once the mixing parameters have been identified, a simple deconvolution can be used to estimate the probability density functions of the source processes. To benchmark our algorithm, we used a database that simulates the one expected from the instruments that will operate onboard ESA's Planck Surveyor Satellite to measure the CMB anisotropies all over the celestial sphere.

  1. Improvement of highly charged ion production in the ECR source of heavy ions

    Shirkov, G.D.

    1996-01-01

    Some physical limitations of the highly charged ion production in the ECR source are analyzed in this report. A few possible ways to improve the output of highly charged ions from the ECR source for heavy ions are proposed. A new library of computer codes for the numerical simulation of heavy ion production in the ECR ion source is used to examine these ways to improve the ECR source operation according to the CERN program of heavy ion acceleration. copyright 1996 American Institute of Physics

  2. Reduced dose uncertainty in MRI-based polymer gel dosimetry using parallel RF transmission with multiple RF sources

    Sang-Young Kim; Jung-Hoon Lee; Jin-Young Jung; Do-Wan Lee; Seu-Ran Lee; Bo-Young Choe; Hyeon-Man Baek; Korea University of Science and Technology, Daejeon; Dae-Hyun Kim; Jung-Whan Min; Ji-Yeon Park

    2014-01-01

    In this work, we present the feasibility of using a parallel RF transmit with multiple RF sources imaging method (MultiTransmit imaging) in polymer gel dosimetry. Image quality and B 1 field homogeneity was statistically better in the MultiTransmit imaging method than in conventional single source RF transmission imaging method. In particular, the standard uncertainty of R 2 was lower on the MultiTransmit images than on the conventional images. Furthermore, the MultiTransmit measurement showed improved dose resolution. Improved image quality and B 1 homogeneity results in reduced dose uncertainty, thereby suggesting the feasibility of MultiTransmit MR imaging in gel dosimetry. (author)

  3. Exopolysaccharides enriched in rare sugars: bacterial sources, production, and applications.

    Roca, Christophe; Alves, Vitor D; Freitas, Filomena; Reis, Maria A M

    2015-01-01

    Microbial extracellular polysaccharides (EPS), produced by a wide range of bacteria, are high molecular weight biopolymers, presenting an extreme diversity in terms of chemical structure and composition. They may be used in many applications, depending on their chemical and physical properties. A rather unexplored aspect is the presence of rare sugars in the composition of some EPS. Rare sugars, such as rhamnose or fucose, may provide EPS with additional biological properties compared to those composed of more common sugar monomers. This review gives a brief overview of these specific EPS and their producing bacteria. Cultivation conditions are summarized, demonstrating their impact on the EPS composition, together with downstream processing. Finally, their use in different areas, including cosmetics, food products, pharmaceuticals, and biomedical applications, are discussed.

  4. Polysaccharides enriched in rare sugars: bacterial sources, production and applications

    Christophe eRoca

    2015-04-01

    Full Text Available Microbial extracellular polysaccharides (EPS, produced by a wide range of bacteria, are high molecular weight biopolymers, presenting an extreme diversity in terms of chemical structure and composition. They may be used in many applications, depending on their chemical and physical properties. A rather unexplored aspect is the presence of rare sugars in the composition of some EPS. Rare sugars, such as rhamnose or fucose, may provide EPS with additional biological properties compared to those composed of more common sugar monomers.This review gives a brief overview of these specific EPS and their producing bacteria. Cultivation conditions are summarized, demonstrating their impact on the EPS composition, together with downstream processing. Finally, their use in different areas, including cosmetics, food products, pharmaceuticals and biomedical applications, are discussed.

  5. Meat and meat products as a source of bioactive peptides

    Alfonso Totosaus

    2016-12-01

    Full Text Available Meat is a high protein content food, with great nutritional and biological value. Meat protein hydrolysis begins with the muscle to meat conversion, during meat ageing. After slaughter, endogen enzymes are responsible of meat softening since myofibrillar anchorage proteins are degraded. Protein hydrolysis continues during food preparation. When meat reaches the stomach, pepsin is the first enzyme to interact. As the food travel trough out gastrointestinal tract, pancreatic enzymes degraded the remained protein and the peptidases made the final proteolysis process. The small proteins or peptides are the absorbed to the circulatory system and distributed to the rest of the body. Bioactive peptides activity of meat and meat products is anti-hypertensive mainly, where histidine, carnosine and anserine are the main peptides identified. Another peptide with anti-oxidant activity is glutathione. The content depends on animal species.

  6. Identifying Sources of Funding That Contribute to Scholastic Productivity in Academic Plastic Surgeons.

    Ruan, Qing Zhao; Cohen, Justin B; Baek, Yoonji; Chen, Austin D; Doval, Andres F; Singhal, Dhruv; Fukudome, Eugene Y; Lin, Samuel J; Lee, Bernard T

    2018-04-01

    Scholastic productivity has previously been shown to be positively associated with National Institute of Health (NIH) grants and industry funding. This study examines whether society, industry, or federal funding contributes toward academic productivity as measured by scholastic output of academic plastic surgeons. Institution Web sites were used to acquire academic attributes of full-time academic plastic surgeons. The Center for Medicare and Medicaid Services Open Payment database, NIH reporter, the Plastic Surgery Foundation (PSF), and American Association of Plastic Surgeons (AAPS) Web sites were accessed for funding and endowment details. Bibliometric data of each surgeon were then collected via Scopus to ascertain strengths of association with each source. Multiple linear regression analysis was used to identify significant contributors to high scholastic output. We identified 935 academic plastic surgeons with 94 (10.1%), 24 (2.6%), 724 (77.4%), and 62 (6.6%) receiving funding from PSF, AAPS, industry, and NIH, respectively. There were positive correlations in receiving NIH, PSF, and/or AAPS funding (P funding was found to negatively associate with PSF (r = -0.75, P = 0.022) grants. The NIH R award was consistently found to be the most predictive of academic output across bibliometrics, followed by the AAPS academic scholarship award. Conventional measures of academic seniority remained predictive across all measures used. Our study demonstrates for the first time interactions between industry, federal, and association funding. The NIH R award was the strongest determinant of high scholastic productivity. Recognition through AAPS academic scholarships seemed to associate with subsequent success in NIH funding.

  7. Source coherence impairments in a direct detection direct sequence optical code-division multiple-access system.

    Fsaifes, Ihsan; Lepers, Catherine; Lourdiane, Mounia; Gallion, Philippe; Beugin, Vincent; Guignard, Philippe

    2007-02-01

    We demonstrate that direct sequence optical code- division multiple-access (DS-OCDMA) encoders and decoders using sampled fiber Bragg gratings (S-FBGs) behave as multipath interferometers. In that case, chip pulses of the prime sequence codes generated by spreading in time-coherent data pulses can result from multiple reflections in the interferometers that can superimpose within a chip time duration. We show that the autocorrelation function has to be considered as the sum of complex amplitudes of the combined chip as the laser source coherence time is much greater than the integration time of the photodetector. To reduce the sensitivity of the DS-OCDMA system to the coherence time of the laser source, we analyze the use of sparse and nonperiodic quadratic congruence and extended quadratic congruence codes.

  8. Source coherence impairments in a direct detection direct sequence optical code-division multiple-access system

    Fsaifes, Ihsan; Lepers, Catherine; Lourdiane, Mounia; Gallion, Philippe; Beugin, Vincent; Guignard, Philippe

    2007-02-01

    We demonstrate that direct sequence optical code- division multiple-access (DS-OCDMA) encoders and decoders using sampled fiber Bragg gratings (S-FBGs) behave as multipath interferometers. In that case, chip pulses of the prime sequence codes generated by spreading in time-coherent data pulses can result from multiple reflections in the interferometers that can superimpose within a chip time duration. We show that the autocorrelation function has to be considered as the sum of complex amplitudes of the combined chip as the laser source coherence time is much greater than the integration time of the photodetector. To reduce the sensitivity of the DS-OCDMA system to the coherence time of the laser source, we analyze the use of sparse and nonperiodic quadratic congruence and extended quadratic congruence codes.

  9. Application of the Modified Source Multiplication (MSM) Technique to Subcritical Reactivity Worth Measurements in Thermal and Fast Reactor Systems

    Blaise, P.; Fougeras, Ph.; Mellier, F.

    2011-01-01

    The Amplified Source Multiplication (ASM) method and its improved Modified Source Multiplication (MSM) method have been widely used in the CEA's EOLE and MASURCA critical facilities over the past decades for the determination of reactivity worths by using fission chambers in subcritical configurations. The ASM methodology uses relatively simple relationships between count rates of efficient miniature fission chambers located in slightly subcritical reference and perturbed configurations. While this method works quite well for small reactivity variations, the raw results need to be corrected to take into account the flux perturbation at the fission chamber location. This is performed by applying to the measurement a correction factor called MSM. This paper describes in detail both methodologies, with their associated uncertainties. Applications on absorber cluster worth in the MISTRAL-4 full MOX mock-up core and the last core loaded in MASURCA show the importance of the MSM correction on raw ASM data. (authors)

  10. Identification of dust storm source areas in West Asia using multiple environmental datasets.

    Cao, Hui; Amiraslani, Farshad; Liu, Jian; Zhou, Na

    2015-01-01

    Sand and Dust storms are common phenomena in arid and semi-arid areas. West Asia Region, especially Tigris-Euphrates alluvial plain, has been recognized as one of the most important dust source areas in the world. In this paper, a method is applied to extract SDS (Sand and Dust Storms) sources in West Asia region using thematic maps, climate and geography, HYSPLIT model and satellite images. Out of 50 dust storms happened during 2000-2013 and collected in form of MODIS images, 27 events were incorporated as demonstrations of the simulated trajectories by HYSPLIT model. Besides, a dataset of the newly released Landsat images was used as base-map for the interpretation of SDS source regions. As a result, six main clusters were recognized as dust source areas. Of which, 3 clusters situated in Tigris-Euphrates plain were identified as severe SDS sources (including 70% dust storms in this research). Another cluster in Sistan plain is also a potential source area. This approach also confirmed six main paths causing dust storms. These paths are driven by the climate system including Siberian and Polar anticyclones, monsoon from Indian Subcontinent and depression from north of Africa. The identification of SDS source areas and paths will improve our understandings on the mechanisms and impacts of dust storms on socio-economy and environment of the region. Copyright © 2014 Elsevier B.V. All rights reserved.

  11. A Tiered Approach to Evaluating Salinity Sources in Water at Oil and Gas Production Sites.

    Paquette, Shawn M; Molofsky, Lisa J; Connor, John A; Walker, Kenneth L; Hopkins, Harley; Chakraborty, Ayan

    2017-09-01

    A suspected increase in the salinity of fresh water resources can trigger a site investigation to identify the source(s) of salinity and the extent of any impacts. These investigations can be complicated by the presence of naturally elevated total dissolved solids or chlorides concentrations, multiple potential sources of salinity, and incomplete data and information on both naturally occurring conditions and the characteristics of potential sources. As a result, data evaluation techniques that are effective at one site may not be effective at another. In order to match the complexity of the evaluation effort to the complexity of the specific site, this paper presents a strategic tiered approach that utilizes established techniques for evaluating and identifying the source(s) of salinity in an efficient step-by-step manner. The tiered approach includes: (1) a simple screening process to evaluate whether an impact has occurred and if the source is readily apparent; (2) basic geochemical characterization of the impacted water resource(s) and potential salinity sources coupled with simple visual and statistical data evaluation methods to determine the source(s); and (3) advanced laboratory analyses (e.g., isotopes) and data evaluation methods to identify the source(s) and the extent of salinity impacts where it was not otherwise conclusive. A case study from the U.S. Gulf Coast is presented to illustrate the application of this tiered approach. © 2017, National Ground Water Association.

  12. Start-up Characteristics of Swallow-tailed Axial-grooved Heat Pipe under the conditions of Multiple Heat Sources

    Zhang, Renping

    2017-12-01

    A mathematical model was developed for predicting start-up characteristics of Swallow-tailed Axial-grooved Heat Pipe under the conditions of Multiple Heat Sources. The effects of heat capacitance of heat source, liquid-vapour interfacial evaporation-condensation heat transfer, shear stress at the interface was considered in current model. The interfacial evaporating mass flow rate is based on the kinetic analysis. Time variations of evaporating mass rate, wall temperature and liquid velocity are studied from the start-up to steady state. The calculated results show that wall temperature demonstrates step transition at the junction between the heat source and non-existent heat source on the evaporator. The liquid velocity changes drastically at the evaporator section, however, it has slight variation at the evaporator section without heat source. When the effect of heat source is ignored, the numerical temperature demonstrates a quicker response. With the consideration of capacitance of the heat source, the data obtained from the proposed model agree well with the experimental results.

  13. Emission and source characterization of monoaromatic hydrocarbons from coke production

    He, Q.S.; Wang, X.M.; Sheng, G.Y.; Fu, J.M. [Chinese Academy of Sciences, Guangzhou (China). State Key Laboratory of Organic Geochemistry

    2005-09-15

    Monoaromatic hydrocarbons (MAHs) from indigenous and industrial coking processes are studied in Shanxi province. They are sampled on the top of coke ovens and in the chimneys using stainless steel canister and determined by GC/MSD after preconcentration with liquid nitrogen. Benzene, toluene and xylene are the main components among MAHs emitted from coking processes. Benzene and the total MAHs concentrations were as high as 3421.0 microg/m3 and 4 865.9 microg/m3 in the air from indigenous coking, 548.7 microg/m3 and 1 054.8 microg/m3 in the oventop air from industrial coking, and 1 376.4 microg/m3 and 1 819.4 microg/m3 in stack gas from industrial coking, respectively. The MAHs concentrations vary greatly during the indigenous coking process, which in the prophase (from firing to 10 days) is obviously higher than in the anaphase (10 days to quenching the coke). In industrial coking the MAHs in the oventop air are highest when charging the coal and next when transferring the hot coke, but in stack gas they are highest when charging coal and lowest when transferring the coke. Benzene, toluene, ethylbenzene and xylene (BTEX) in industrial coking samples show good linearity, indicating that MAHs in industrial coking might come predominantly from coal pyrolysis; but BTEX distribute dispersedly in indigenous coking samples, indicating that its emission might be affected by many factors. In all samples BTEX ratios especially high B/E ratio, is unique among MAHs sources, and might be helpful to characterize pollution from coking.

  14. [Emission and source characterization of monoaromatic hydrocarbons from coke production].

    He, Qiu-Sheng; Wang, Xin-Ming; Sheng, Guo-Ying; Fu, Jia-Mo

    2005-09-01

    Monoaromatic hydrocarbons (MAHs) from indigenous and industrial coking processes are studied in Shanxi province. They are sampled on the top of coke ovens and in the chimneys using stainless steel canister and determined by GC/MSD after preconcentration with liquid nitrogen. Benzene, toluene and xylene are the main components among MAHs emitted from coking processes. Benzene and the total MAHs concentrations were as high as 3421.0 microg/m3 and 4 865.9 microg/m3 in the air from indigenous coking, 548.7 microg/m3 and 1 054.8 microg/m3 in the oventop air from industrial coking, and 1 376.4 microg/m3 and 1 819.4 microg/m3 in stack gas from industrial coking, respectively. The MAHs concentrations vary greatly during the indigenous coking process, which in the prophase (from firing to 10 days) is obviously higher than in the anaphase (10 days to quenching the coke). In industrial coking the MAHs in the oventop air are highest when charging the coal and next when transferring the hot coke, but in stack gas they are highest when charging coal and lowest when transferring the coke. Benzene, toluene, ethylbenzene and xylene (BTEX) in industrial coking samples show good linearity, indicating that MAHs in industrial coking might come predominantly from coal pyrolysis; but BTEX distribute dispersedly in indigenous coking samples, indicating that its emission might be affected by many factors. In all samples BTEX ratios especially high B/E ratio, is unique among MAHs sources, and might be helpful to characterize pollution from coking.

  15. Multiple sources of metals of mineralization in Lower Cambrian black shales of South China: Evidence from geochemical and petrographic study

    Pašava, J.; Kříbek, B.; Vymazalová, A.; Sýkorová, Ivana; Žák, Karel; Orberger, B.

    2008-01-01

    Roč. 58, č. 1 (2008), s. 25-42 ISSN 1344-1698 R&D Projects: GA AV ČR IAA300460510 Institutional research plan: CEZ:AV0Z30460519; CEZ:AV0Z30130516 Keywords : multiple source * Cambrian Ni-Mo-polymetalic black shale * SEDEX barite deposit Subject RIV: DD - Geochemistry Impact factor: 0.377, year: 2008

  16. Design and simulation of ion optics for ion sources for production of singly charged ions

    Zelenak, A.; Bogomolov, S. L.

    2004-05-01

    During the last 2 years different types of the singly charged ion sources were developed for FLNR (JINR) new projects such as Dubna radioactive ion beams, (Phase I and Phase II), the production of the tritium ion beam and the MASHA mass separator. The ion optics simulations for 2.45 GHz electron cyclotron resonance source, rf source, and the plasma ion source were performed. In this article the design and simulation results of the optics of new ion sources are presented. The results of simulation are compared with measurements obtained during the experiments.

  17. Design and simulation of ion optics for ion sources for production of singly charged ions

    Zelenak, A.; Bogomolov, S.L.

    2004-01-01

    During the last 2 years different types of the singly charged ion sources were developed for FLNR (JINR) new projects such as Dubna radioactive ion beams, (Phase I and Phase II), the production of the tritium ion beam and the MASHA mass separator. The ion optics simulations for 2.45 GHz electron cyclotron resonance source, rf source, and the plasma ion source were performed. In this article the design and simulation results of the optics of new ion sources are presented. The results of simulation are compared with measurements obtained during the experiments

  18. Patterns, Perception and Behavior of Electronic Nicotine Delivery Systems Use and Multiple Product Use Among Young Adults.

    Martinasek, Mary P; Bowersock, Amy; Wheldon, Christopher W

    2018-03-27

    Electronic nicotine delivery systems (ENDS) are battery-operated devices used to inhale vaporized or aerosolized nicotine. There is increasing research uncovering negative health effects of these devices. Less is known about the social and behavioral aspects among college students. This cross-sectional study was conducted at a mid-sized private university in Florida. The survey was sent via e-mail to the student body of undergraduates. A final sample size of 989 students was analyzed to understand demographic differences between users and nonusers, initiation factors, and influencers, as well as multiple product behaviors. Approximately 51.4% ( n = 508) of participants reported ever using an ENDS and other tobacco consumption. Males were significantly more likely to be users of ENDS. Polytobacco use, or the use of multiple tobacco products, was also more common among participants who have tried ENDS ( P influencer for initial use. A 4-class latent variable model differentiated between usage patterns characterized as abstainers (70%), hookah users only (14%), ENDS only (11%), and polytobacco users (4%). ENDS are not commonly used as a quit tool among college students, but rather as a secondary source of nicotine, most commonly in current smokers. Copyright © 2018 by Daedalus Enterprises.

  19. Pullulan production by Aureobasidium pullulans grown on ethanol stillage as a nitrogen source.

    West, T P; Strohfus, B

    1996-01-01

    Pullulan production by Aureobasidium pullulans strain RP-1 using thin stillage from fuel ethanol production as a nitrogen source was studied in a medium using corn syrup as a carbon source. The use of 1% thin stillage as a nitrogen source instead of ammonium sulphate elevated polysaccharide production by strain RP-1 cells when grown on a concentration of up to 7.5% corn syrup, independent of yeast extract supplementation. Dry weights of cells grown in medium containing ammonium sulphate as the nitrogen source were higher than the stillage-grown cells after 7 days of growth. The viscosity of the polysaccharide on day 7 was higher for cells grown on thin stillage rather than ammonium sulphate as a nitrogen source. The pullulan content of the polysaccharide elaborated by ammonium sulphate-grown cells on day 7 was higher than the pullulan content of polysaccharide produced by stillage-grown cells regardless of whether yeast extract was added to the culture medium.

  20. Multiple particles production for hadron-hadron reactions with finite hadronization time

    Arbex, N.

    1991-01-01

    Experimental data on multiple particle production for proton-proton reaction are analysed in the context of a very simple analytical model. The model exhibits the essential features of hydrodynamical calculations as, e.g., the formation of an intermediate object, which undergoes expansion. The simultaneous analysis of different types of data allows for the conclusion that such data reflect the dynamics of this intermediate object and have a very deem connection to the elementary processes. (author)

  1. Statistical model of hadrons multiple production in space of total angular momentum and isotopic spin

    Gridneva, S.A.; Rus'kin, V.I.

    1980-01-01

    Basic features of the statistical model of multiple hadron production based on microcanonical distribution and taking into account the laws of conservation of total angular momentum, isotopic spin, p-, G-, C-eveness and Bose-Einstein statistics requirements are given. The model predictions are compared with experimental data on anti NN annihilation at rest and e + e - annihilation in hadrons at annihilation total energy from 2 to 3 GeV [ru

  2. 77 FR 33486 - Certain Integrated Circuit Packages Provided With Multiple Heat-Conducting Paths and Products...

    2012-06-06

    ...Notice is hereby given that the U.S. International Trade Commission has received a complaint entitled Certain Integrated Circuit Packages Provided With Multiple Heat-Conducting Paths and Products Containing Same, DN 2899; the Commission is soliciting comments on any public interest issues raised by the complaint or complainant's filing under section 210.8(b) of the Commission's Rules of Practice and Procedure (19 CFR 210.8(b)).

  3. On Measurement of Efficiency of Cobb-Douglas Production Function with Additive and Multiplicative Errors

    Md. Moyazzem Hossain

    2015-02-01

    Full Text Available In developing counties, efficiency of economic development has determined by the analysis of industrial production. An examination of the characteristic of industrial sector is an essential aspect of growth studies. The most of the developed countries are highly industrialized as they brief “The more industrialization, the more development”. For proper industrialization and industrial development we have to study industrial input-output relationship that leads to production analysis. For a number of reasons econometrician’s belief that industrial production is the most important component of economic development because, if domestic industrial production increases, GDP will increase, if elasticity of labor is higher, implement rates will increase and investment will increase if elasticity of capital is higher. In this regard, this paper should be helpful in suggesting the most suitable Cobb-Douglas production function to forecast the production process for some selected manufacturing industries of developing countries like Bangladesh. This paper choose the appropriate Cobb-Douglas function which gives optimal combination of inputs, that is, the combination that enables it to produce the desired level of output with minimum cost and hence with maximum profitability for some selected manufacturing industries of Bangladesh over the period 1978-79 to 2011-2012. The estimated results shows that the estimates of both capital and labor elasticity of Cobb-Douglas production function with additive errors are more efficient than those estimates of Cobb-Douglas production function with multiplicative errors.

  4. The impact of animal source food products on human nutrition and ...

    The impact of animal source food products on human nutrition and health. ... the widest array of complex scientific, economic, environmental and political issues. ... investment in research and extrapolation of information towards appropriate ...

  5. FormScanner: Open-Source Solution for Grading Multiple-Choice Exams

    Young, Chadwick; Lo, Glenn; Young, Kaisa; Borsetta, Alberto

    2016-01-01

    The multiple-choice exam remains a staple for many introductory physics courses. In the past, people have graded these by hand or even flaming needles. Today, one usually grades the exams with a form scanner that utilizes optical mark recognition (OMR). Several companies provide these scanners and particular forms, such as the eponymous…

  6. Isolating and Examining Sources of Suppression and Multicollinearity in Multiple Linear Regression

    Beckstead, Jason W.

    2012-01-01

    The presence of suppression (and multicollinearity) in multiple regression analysis complicates interpretation of predictor-criterion relationships. The mathematical conditions that produce suppression in regression analysis have received considerable attention in the methodological literature but until now nothing in the way of an analytic…

  7. Using Multiple Sources of Information in Establishing Text Complexity. Reading Research Report. #11.03

    Hiebert, Elfrieda H.

    2011-01-01

    A focus of the Common Core State Standards/English Language Arts (CCSS/ELA) is that students become increasingly more capable with complex text over their school careers. This focus has redirected attention to the measurement of text complexity. Although CCSS/ELA suggests multiple criteria for this task, the standards offer a single measure of…

  8. Part 2. Development of Enhanced Statistical Methods for Assessing Health Effects Associated with an Unknown Number of Major Sources of Multiple Air Pollutants.

    Park, Eun Sug; Symanski, Elaine; Han, Daikwon; Spiegelman, Clifford

    2015-06-01

    model with five sources (that seemed to be refinery, petrochemical production, gasoline evaporation, natural gas, and vehicular exhaust) among several candidate models, with the number of sources varying between three and seven and with different identifiability conditions. Our multipollutant approach assessing source-specific health effects is more advantageous than a single-pollutant approach in that it can estimate total health effects from multiple pollutants and can also identify emission sources that are responsible for adverse health effects. Our Bayesian approach can incorporate not only uncertainty in the estimated source contributions, but also model uncertainty that has not been addressed in previous studies on assessing source-specific health effects. The new Bayesian spatial multivariate receptor modeling approach enables predictions of source contributions at unmonitored sites, minimizing exposure misclassification and providing improved exposure estimates along with their uncertainty estimates, as well as accounting for uncertainty in the number of sources and identifiability conditions.

  9. An integrated multi−period planning of the production and transportation of multiple petroleum products in a single pipeline system

    Alberto Herrán

    2011-01-01

    Full Text Available A multiproduct pipeline provides an economic way to transport large volumes of refined petroleum products over long distances. In such a pipeline, different products are pumped back−to−back without any separation device between them. The sequence and lengths of such pumping runs must be carefully selected in order to meet market demands while minimizing pipeline operational costs and satisfying several constraints. The production planning and scheduling of the products at the refinery must also be synchronized with the transportation in order to avoid the usage of the system at some peak−hour time intervals. In this paper, we propose a multi−period mixed integer nonlinear programming (MINLP model for an optimal planning and scheduling of the production and transportation of multiple petroleum products from a refinery plant connected to several depots through a single pipeline system. The objective of this work is to generalize the mixed integer linear programming (MILP formulation proposed by Cafaro and Cerdá (2004, Computers and Chemical Engineering where only a single planning period was considered and the production planning and scheduling was not part of the decision process. Numerical examples show how the use of a single period model for a given time period may lead to infeasible solutions when it is used for the upcoming periods. These examples also show how integrating production planning with the transportation and the use of a multi−period model may result in a cost saving compared to using a single−period model for each period, independently.

  10. Sucrose Fermentation by Brazilian Ethanol Production Yeasts in Media Containing Structurally Complex Nitrogen Sources

    Miranda Junior, Messias [UNESP; Batistote, Margareth [UNESP; Cilli, Eduardo Maffud [UNESP; Ernandes, Jose Roberto [UNESP

    2009-01-01

    Four Saccharomyces cerevisiae Brazilian industrial ethanol production strains were grown, under shaken and static conditions, in media containing 22% (w/v) sucrose supplemented with nitrogen sources varying from a single ammonium salt (ammonium sulfate) to free amino acids (casamino acids) and peptides (peptone). Sucrose fermentations by Brazilian industrial ethanol production yeasts strains were strongly affected by both the structural complexity of the nitrogen source and the availability o...

  11. Noise analysis of a white-light supercontinuum light source for multiple wavelength confocal laser scanning fluorescence microscopy

    McConnell, Gail [Centre for Biophotonics, Strathclyde Institute for Biomedical Sciences, University of Strathclyde, 27 Taylor Street, Glasgow, G4 0NR (United Kingdom)

    2005-08-07

    Intensity correlations of a Ti : sapphire, Kr/Ar and a white-light supercontinuum were performed to quantify the typical signal amplitude fluctuations and hence ascertain the comparative output stability of the white-light supercontinuum source for confocal laser scanning microscopy (CLSM). Intensity correlations across a two-pixel sample (n = 1000) of up to 98%, 95% and 94% were measured for the Ti : sapphire, Kr/Ar and white-light supercontinuum source, respectively. The white-light supercontinuum noise level is therefore acceptable for CLSM, with the added advantage of wider wavelength flexibility over traditional CLSM excitation sources. The relatively low-noise white-light supercontinuum was then used to perform multiple wavelength sequential CLSM of guinea pig detrusor to confirm the reliability of the system and to demonstrate system flexibility.

  12. 16 CFR 18.8 - Deception as to origin or source of industry products.

    2010-01-01

    ... misrepresentation as to source or origin (e.g., “Colorado Blue Spruce,” “Arizona Cypress,” “Black Hills Spruce... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Deception as to origin or source of industry... GUIDES FOR THE NURSERY INDUSTRY § 18.8 Deception as to origin or source of industry products. (a) It is...

  13. The role of designer expertise in source selection during product metaphor generation

    Cila, N.; Hekkert, P.P.M.; Visch, V.T.

    2012-01-01

    Metaphors have a communicative role in design that entails a transfer of meaning from an entity (i.e. source) to the designed product (i.e. target). In this paper, we investigate the effect of the expertise of designer on the accessibility of the sources that they employ in metaphors. In the study

  14. The impact of animal source food products on human nutrition and ...

    FBDG

    Associates of the Institute of Food, Nutrition and Well-being, University of ... nutrition), the role of animal source foods as part of a healthy diet requires continuous investment ... Keywords: Animal source foods, livestock products, nutrition, health ..... sensation of fullness that persists after eating until hunger returns (Benelam, ...

  15. Optimizing the regimes of the Advanced LIGO gravitational wave detector for multiple source types

    Kondrashov, I. S.; Simakov, D. A.; Khalili, F. Ya.; Danilishin, S. L.

    2008-01-01

    We developed algorithms which allow us to find regimes of the signal-recycled Fabry-Perot-Michelson interferometer [for example, the Advanced Laser Interferometric Gravitational Wave Observatory (LIGO)], optimized concurrently for two (binary inspirals + bursts) and three (binary inspirals + bursts + millisecond pulsars) types of gravitational wave sources. We show that there exists a relatively large area in the interferometer parameters space where the detector sensitivity to the first two kinds of sources differs only by a few percent from the maximal ones for each kind of source. In particular, there exists a specific regime where this difference is ≅0.5% for both of them. Furthermore, we show that even more multipurpose regimes are also possible that provide significant sensitivity gain for millisecond pulsars with only minor sensitivity degradation for binary inspirals and bursts.

  16. Multiple human schemas and the communication-information sources use: An application of Q-methodology

    Mansour Shahvali

    2014-12-01

    Full Text Available This study was conducted with the aim of developing a communication and information model for greenhouse farmers in Yazd city using schema theory. Performing the Q methodology together with the factor analysis, as such, the different variables were loaded over the five schematic factors which included the human philosophical nature, ideological, economic, social, and environmental-conservation beliefs. Running AMOS,of course, it was also unveiled that the philosophical, ideological, social, economic and environmental schemas influence directly on the personal communication-information sources use. Furthermore, the environmental-conservation schema affects directly and indirectly the personal communication-information sources use. More importantly, this study indicated the important role of the indigenous sources which play in constructing, evaluating and retrieving the environmental knowledge in respondents. The research predisposes a suitable context for policymakers who seek to draw up much more effective and appropriate communication and information strategies to address the specific target groups’ needs.

  17. The Fashion Retail and the value creation with sustainable products: a multiple case study

    Eleonora Alves Baptista

    2016-06-01

    Full Text Available This study aims to understand how the development of sustainable products in Brazilian fashion retail businesses creates value for the companies themselves, society and the environment. A qualitative approach to multiple case study method investigates practices and processes at four companies from Rio de Janeiro State. The study collected primary information from direct observation and interviews with the firms’ directors, and secondary data from industry reports and other documents. Three overall dimensions of the study - environmental management, value creation and product development in fast fashion companies - encoded into seven categories, when considered in data crosssynthesis, elucidate the following conclusions: (1 the firms do not have economic, ethical and legal fields integrated view; (2 the companies do not believe that the fashion consumer market values environmental practices and thus not motivated to invest in practices and products; (3 a fragmented supply chain makes it difficult to control activities and appears as a major constraint to the development of sustainable products; (4 access to information on best environmental practices and tax incentives are important inductors’ mechanisms to leverage the development of sustainable products in the Brazilian fashion retail; (5 the development of strategic capabilities in pollution prevention area, management products and clean technology create value for the production chain.

  18. Ionizing radiation sources: very diversified means, multiple applications and a changing regulatory environment. Conference proceedings

    2011-11-01

    This document brings together the available presentations given at the conference organised by the French society of radiation protection about ionizing radiation source means, applications and regulatory environment. Twenty eight presentations (slides) are compiled in this document and deal with: 1 - Overview of sources - some quantitative data from the national inventory of ionizing radiation sources (Yann Billarand, IRSN); 2 - Overview of sources (Jerome Fradin, ASN); 3 - Regulatory framework (Sylvie Rodde, ASN); 4 - Alternatives to Iridium radiography - the case of pressure devices at the manufacturing stage (Henri Walaszek, Cetim; Bruno Kowalski, Welding Institute); 5 - Dosimetric stakes of medical scanner examinations (Jean-Louis Greffe, Charleroi hospital of Medical University); 6 - The removal of ionic smoke detectors (Bruno Charpentier, ASN); 7 - Joint-activity and reciprocal liabilities - Organisation of labour risk prevention in case of companies joint-activity (Paulo Pinto, DGT); 8 - Consideration of gamma-graphic testing in the organization of a unit outage activities (Jean-Gabriel Leonard, EDF); 9 - Radiological risk control at a closed and independent work field (Stephane Sartelet, Areva); 10 - Incidents and accidents status and typology (Pascale Scanff, IRSN); 11 - Regional overview of radiation protection significant events (Philippe Menechal, ASN); 12 - Incident leading to a tritium contamination in and urban area - consequences and experience feedback (Laurence Fusil, CEA); 13 - Experience feedback - loss of sealing of a calibration source (Philippe Mougnard, Areva); 14 - Blocking incident of a 60 Co source (Bruno Delille, Salvarem); 15 - Triggering of gantry's alarm: status of findings (Philippe Prat, Syctom); 16 - Non-medical electric devices: regulatory changes (Sophie Dagois, IRSN; Jerome Fradin, ASN); 17 - Evaluation of the dose equivalent rate in pulsed fields: method proposed by the IRSN and implementation test (Laurent Donadille, IRSN

  19. Multiple information sources and consequences of conflicting information about medicine use during pregnancy: a multinational Internet-based survey.

    Hämeen-Anttila, Katri; Nordeng, Hedvig; Kokki, Esa; Jyrkkä, Johanna; Lupattelli, Angela; Vainio, Kirsti; Enlund, Hannes

    2014-02-20

    A wide variety of information sources on medicines is available for pregnant women. When using multiple information sources, there is the risk that information will vary or even conflict. The objective of this multinational study was to analyze the extent to which pregnant women use multiple information sources and the consequences of conflicting information, and to investigate which maternal sociodemographic, lifestyle, and medical factors were associated with these objectives. An anonymous Internet-based questionnaire was made accessible during a period of 2 months, on 1 to 4 Internet websites used by pregnant women in 5 regions (Eastern Europe, Western Europe, Northern Europe, Americas, Australia). A total of 7092 responses were obtained (n=5090 pregnant women; n=2002 women with a child younger than 25 weeks). Descriptive statistics and logistic regression analysis were used. Of the respondents who stated that they needed information, 16.16% (655/4054) used one information source and 83.69% (3393/4054) used multiple information sources. Of respondents who used more than one information source, 22.62% (759/3355) stated that the information was conflicted. According to multivariate logistic regression analysis, factors significantly associated with experiencing conflict in medicine information included being a mother (OR 1.32, 95% CI 1.11-1.58), having university (OR 1.33, 95% CI 1.09-1.63) or other education (OR 1.49, 95% CI 1.09-2.03), residing in Eastern Europe (OR 1.52, 95% CI 1.22-1.89) or Australia (OR 2.28, 95% CI 1.42-3.67), use of 3 (OR 1.29, 95% CI 1.04-1.60) or >4 information sources (OR 1.82, 95% CI 1.49-2.23), and having ≥2 chronic diseases (OR 1.49, 95% CI 1.18-1.89). Because of conflicting information, 43.61% (331/759) decided not to use medication during pregnancy, 30.30% (230/759) sought a new information source, 32.67% (248/759) chose to rely on one source and ignore the conflicting one, 25.03% (190/759) became anxious, and 2.64% (20/759) did

  20. Research on numerical method for multiple pollution source discharge and optimal reduction program

    Li, Mingchang; Dai, Mingxin; Zhou, Bin; Zou, Bin

    2018-03-01

    In this paper, the optimal method for reduction program is proposed by the nonlinear optimal algorithms named that genetic algorithm. The four main rivers in Jiangsu province, China are selected for reducing the environmental pollution in nearshore district. Dissolved inorganic nitrogen (DIN) is studied as the only pollutant. The environmental status and standard in the nearshore district is used to reduce the discharge of multiple river pollutant. The research results of reduction program are the basis of marine environmental management.

  1. Heavy-flavour production as a function of multiplicity in pp collisions at ALICE

    CERN. Geneva

    2015-01-01

    The measurement of inclusive heavy-flavour production cross sections in proton-proton (pp) collisions at LHC energies constituted an important test of perturbative QCD calculations. The measured cross sections can be described within uncertainties by next-to-leading order (NLO) and fixed-order with next-to-leading-log re-summation (FONLL) calculations with collinear factorization, as well as by leading-order (LO) calculations in the kt-factorization approach. More differential measurements of charm and beauty production in pp collisions can provide further information about the particle production mechanisms. The production of prompt D mesons and non-prompt J/psi mesons in proton-proton collisions at a centre-of-mass energy of 7 TeV was measured by the ALICE Collaboration as a function of the multiplicity of charged particles produced in the collision. D0, D+ and D*+ mesons were reconstructed from their hadronic decay channels in the central rapidity region and their yields were measured in different multipl...

  2. Memory for Textual Conflicts Predicts Sourcing When Adolescents Read Multiple Expository Texts

    Stang Lund, Elisabeth; Bråten, Ivar; Brante, Eva W.; Strømsø, Helge I.

    2017-01-01

    This study investigated whether memory for conflicting information predicted mental representation of source-content links (i.e., who said what) in a sample of 86 Norwegian adolescent readers. Participants read four texts presenting conflicting claims about sun exposure and health. With differences in gender, prior knowledge, and interest…

  3. Recent performances of the multiple charged heavy-ion source - triple mafios

    Briand, P.; Chan-tung, N.; Geller, R.; Jacquot, B.

    1977-01-01

    The principle and the characteristics of the ion source are described. We also furnish upto date performances concerning ion currents, globale emittances of the beam as well as the emittances of Ar 1+ to Ar 10+ in the radial and axial planes. (orig./WL) [de

  4. Analysis of carbon monoxide production in multihundred-watt heat sources

    Peterson, D.E.; Mulford, R.N.R.

    1976-05-01

    The production of carbon monoxide observed within Multihundred Watt heat sources placed under storage conditions was analyzed. Results of compositional and isotopic analyses of gas taps performed on eight heat sources are summarized and interpreted. Several proposed CO generation mechanisms are examined theoretically and assessed by applying thermodynamic principles. Outgassing of the heat source graphite followed by oxygen isotopic exchange through the vent assemblies appears to explain the CO production at storage temperatures. Reduction of the plutonia fuel sphere by the CO is examined as a function of temperature and stoichiometry. Experiments that could be performed to investigate possible CO generation mechanisms are discussed

  5. Estimate of production of medical isotopes by photo-neutron reaction at the Canadian Light Source

    Szpunar, B.; Rangacharyulu, C.; Daté, S.; Ejiri, H.

    2013-11-01

    In contrast to conventional bremsstrahlung photon beam sources, laser backscatter photon sources at electron synchrotrons provide the capability to selectively tune photons to energies of interest. This feature, coupled with the ubiquitous giant dipole resonance excitations of atomic nuclei, promises a fertile method of nuclear isotope production. In this article, we present the results of simulations of production of the medical/industrial isotopes 196Au, 192Ir and 99Mo by (γ,n) reactions. We employ FLUKA Monte Carlo code along with the simulated photon flux for a beamline at the Canadian Light Source in conjunction with a CO2 laser system.

  6. Nitrous oxide production, its source and distribution in urine patches on grassland on peat soil.

    Koops, J.G.; Beusichem, van M.L.; Oenema, O.

    1997-01-01

    Urine patches are considered to be important sites for nitrous oxide (N2O) production through nitrification and denitrification due to their high concentration of nitrogen (N). The aim of the present study was to determine the microbial source and size of production of N2O in different zones of a

  7. Production of calibration sources and/or radioactive tracers with the cyclotron CV-28

    Osso Junior, Joao Alberto

    1995-01-01

    The present stage of production of calibration sources and radioactive tracers with the Cyclotron CV-28 is described. Among the methods already developed special attention is given to the production of 57 Co, 109 Cd and 111 In. (author). 3 refs

  8. 40 CFR Table 1 to Subpart Xxxx of... - Emission Limits for Tire Production Affected Sources

    2010-07-01

    ... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Emission Limits for Tire Production Affected Sources 1 Table 1 to Subpart XXXX of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION.... 63, Subpt. XXXX, Table 1 Table 1 to Subpart XXXX of Part 63—Emission Limits for Tire Production...

  9. Fuzzy linear model for production optimization of mining systems with multiple entities

    Vujic, Slobodan; Benovic, Tomo; Miljanovic, Igor; Hudej, Marjan; Milutinovic, Aleksandar; Pavlovic, Petar

    2011-12-01

    Planning and production optimization within multiple mines or several work sites (entities) mining systems by using fuzzy linear programming (LP) was studied. LP is the most commonly used operations research methods in mining engineering. After the introductory review of properties and limitations of applying LP, short reviews of the general settings of deterministic and fuzzy LP models are presented. With the purpose of comparative analysis, the application of both LP models is presented using the example of the Bauxite Basin Niksic with five mines. After the assessment, LP is an efficient mathematical modeling tool in production planning and solving many other single-criteria optimization problems of mining engineering. After the comparison of advantages and deficiencies of both deterministic and fuzzy LP models, the conclusion presents benefits of the fuzzy LP model but is also stating that seeking the optimal plan of production means to accomplish the overall analysis that will encompass the LP model approaches.

  10. Evaluation of Personal and Built Environment Attributes to Physical Activity: A Multilevel Analysis on Multiple Population-Based Data Sources

    Wei Yang

    2012-01-01

    Full Text Available Background. Studies have documented that built environment factors potentially promote or impede leisure time physical activity (LTPA. This study explored the relationship between multiple built environment factors and individual characteristics on LTPA. Methods. Multiple data sources were utilized including individual level data for health behaviors and health status from the Nevada Behavioral Risk Factor Surveillance System (BRFSS and community level data from different data sources including indicators for recreation facilities, safety, air quality, commute time, urbanization, population density, and land mix level. Mixed model logistic regression and geographic information system (GIS spatial analysis were conducted. Results. Among 6,311 respondents, 24.4% reported no LTPA engagement during the past 30 days. No engagement in LTPA was significantly associated with (1 individual factors: older age, less education, lower income, being obesity, and low life satisfaction and (2 community factors: more commute time, higher crime rate, urban residence, higher population density, but not for density and distance to recreation facilities, air quality, and land mix. Conclusions. Multiple data systems including complex population survey and spatial analysis are valuable tools on health and built environment studies.

  11. Multiple production of hadrons at high energies in the model of quark-gluon strings

    Kaidalov, A.B.; Ter-Martirosyan, K.A.

    1983-01-01

    Multiple production of hadrons at high energies is considered in the framework of the approach based on a picture of formation and subsequent fission of the quark-gluon strings, corresponding to the Pomeron with αsub(P)(0) > 1. The topological (1/nsub(f))-expansion and the colour-tube model is used. Inclusive cross-sections are expressed in therms of the structure functions and fragmentation functions of quarks and their limiting values are in an agreement with the results of the reggeon theory. It is pointed out that an account of rapidity fluctuations of the ends of the quark-gluon strings, connected to valence or sea quarks, allows one to explain a number of characteristic features of the multiple production of hadrons. In particular the model, which takes into account multipomeron configurations, reproduces the experimentally observed rise of inclusive spectra in a central region and well describes both rapidity and multiplicity distributions of charged particles up to energies of the SPS-collider. It is shown that in this approach the KNO-scaling is only approximately satisfied and the pattern of its violation at energies √ s approximately 10 3 GeV is predicted. Inclusive spectra are investigated in the whole region 0 or approximately 0.1) Feynman scaling is violated only logarithmically and deviations from it are very rsmall at s 3 +10 4 GeV

  12. Locating non-volcanic tremor along the San Andreas Fault using a multiple array source imaging technique

    Ryberg, T.; Haberland, C.H.; Fuis, G.S.; Ellsworth, W.L.; Shelly, D.R.

    2010-01-01

    Non-volcanic tremor (NVT) has been observed at several subduction zones and at the San Andreas Fault (SAF). Tremor locations are commonly derived by cross-correlating envelope-transformed seismic traces in combination with source-scanning techniques. Recently, they have also been located by using relative relocations with master events, that is low-frequency earthquakes that are part of the tremor; locations are derived by conventional traveltime-based methods. Here we present a method to locate the sources of NVT using an imaging approach for multiple array data. The performance of the method is checked with synthetic tests and the relocation of earthquakes. We also applied the method to tremor occurring near Cholame, California. A set of small-aperture arrays (i.e. an array consisting of arrays) installed around Cholame provided the data set for this study. We observed several tremor episodes and located tremor sources in the vicinity of SAF. During individual tremor episodes, we observed a systematic change of source location, indicating rapid migration of the tremor source along SAF. ?? 2010 The Authors Geophysical Journal International ?? 2010 RAS.

  13. Production and characterization of cellulolytic enzymes from Trichoderma reesei grown on various carbon sources

    Warzywoda, Michel; Labre, Elisabeth; Pourquie, Jacques [Institut Francais du Petrole (IFP), 92 - Rueil-Malmaison (France)

    1992-01-01

    Ethanol production from lignocellulosics is considered, using a process in which biomass is first pretreated by steam explosion, yielding freely water-extractible pentoses and a cellulose-rich residue which can be further hydrolyzed by cellulases into glucose to be fermented into ethanol. Results that are reported show that both the pentose extracts and the glucose-rich hydrolyzates can be used as carbon sources for cellulase production by Trichoderma reesei. When compared with lactose as the main carbon source, pentose extracts support lower but satisfactory protein productions which are characterized by an increase in hemicellulolytic activities, which significantly improves the saccharifying potential of these enzyme preparations. (author).

  14. A method for untriggered time-dependent searches for multiple flares from neutrino point sources

    Gora, D.; Bernardini, E.; Cruz Silva, A.H.

    2011-04-01

    A method for a time-dependent search for flaring astrophysical sources which can be potentially detected by large neutrino experiments is presented. The method uses a time-clustering algorithm combined with an unbinned likelihood procedure. By including in the likelihood function a signal term which describes the contribution of many small clusters of signal-like events, this method provides an effective way for looking for weak neutrino flares over different time-scales. The method is sensitive to an overall excess of events distributed over several flares which are not individually detectable. For standard cases (one flare) the discovery potential of the method is worse than a standard time-dependent point source analysis with unknown duration of the flare by a factor depending on the signal-to-background level. However, for flares sufficiently shorter than the total observation period, the method is more sensitive than a time-integrated analysis. (orig.)

  15. A method for untriggered time-dependent searches for multiple flares from neutrino point sources

    Gora, D. [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany); Institute of Nuclear Physics PAN, Cracow (Poland); Bernardini, E.; Cruz Silva, A.H. [Institute of Nuclear Physics PAN, Cracow (Poland)

    2011-04-15

    A method for a time-dependent search for flaring astrophysical sources which can be potentially detected by large neutrino experiments is presented. The method uses a time-clustering algorithm combined with an unbinned likelihood procedure. By including in the likelihood function a signal term which describes the contribution of many small clusters of signal-like events, this method provides an effective way for looking for weak neutrino flares over different time-scales. The method is sensitive to an overall excess of events distributed over several flares which are not individually detectable. For standard cases (one flare) the discovery potential of the method is worse than a standard time-dependent point source analysis with unknown duration of the flare by a factor depending on the signal-to-background level. However, for flares sufficiently shorter than the total observation period, the method is more sensitive than a time-integrated analysis. (orig.)

  16. Monitoring of conditions inside gas aggregation cluster source during production of Ti/TiOx nanoparticles

    Kousal, J.; Kolpaková, A.; Shelemin, A.; Kudrna, P.; Tichý, M.; Kylián, O.; Hanuš, J.; Choukourov, A.; Biederman, H.

    2017-10-01

    Gas aggregation sources are nowadays rather widely used in the research community for producing nanoparticles. However, the direct diagnostics of conditions inside the source are relatively scarce. In this work, we focused on monitoring the plasma parameters and the composition of the gas during the production of the TiOx nanoparticles. We studied the role of oxygen in the aggregation process and the influence of the presence of the particles on the plasma. The construction of the source allowed us to make a 2D map of the plasma parameters inside the source.

  17. Deterministic approach for multiple-source tsunami hazard assessment for Sines, Portugal

    Wronna, M.; Omira, R.; Baptista, M. A.

    2015-01-01

    In this paper, we present a deterministic approach to tsunami hazard assessment for the city and harbour of Sines, Portugal, one of the test sites of project ASTARTE (Assessment, STrategy And Risk Reduction for Tsunamis in Europe). Sines has one of the most important deep-water ports, which has oil-bearing, petrochemical, liquid-bulk, coal, and container terminals. The port and its industrial infrastructures face the ocean southwest towards the main seismogenic sources. This...

  18. Scenario based approach for multiple source Tsunami Hazard assessment for Sines, Portugal

    M. Wronna; R. Omira; M. A. Baptista

    2015-01-01

    In this paper, we present a scenario-based approach for tsunami hazard assessment for the city and harbour of Sines – Portugal, one of the test-sites of project ASTARTE. Sines holds one of the most important deep-water ports which contains oil-bearing, petrochemical, liquid bulk, coal and container terminals. The port and its industrial infrastructures are facing the ocean southwest towards the main seismogenic sources. This work considers two different seis...

  19. Using Generalizability Theory to Disattenuate Correlation Coefficients for Multiple Sources of Measurement Error.

    Vispoel, Walter P; Morris, Carrie A; Kilinc, Murat

    2018-05-02

    Over the years, research in the social sciences has been dominated by reporting of reliability coefficients that fail to account for key sources of measurement error. Use of these coefficients, in turn, to correct for measurement error can hinder scientific progress by misrepresenting true relationships among the underlying constructs being investigated. In the research reported here, we addressed these issues using generalizability theory (G-theory) in both traditional and new ways to account for the three key sources of measurement error (random-response, specific-factor, and transient) that affect scores from objectively scored measures. Results from 20 widely used measures of personality, self-concept, and socially desirable responding showed that conventional indices consistently misrepresented reliability and relationships among psychological constructs by failing to account for key sources of measurement error and correlated transient errors within occasions. The results further revealed that G-theory served as an effective framework for remedying these problems. We discuss possible extensions in future research and provide code from the computer package R in an online supplement to enable readers to apply the procedures we demonstrate to their own research.

  20. Identification of Multiple Subtypes of Campylobacter jejuni in Chicken Meat and the Impact on Source Attribution

    John A. Hudson

    2013-09-01

    Full Text Available Most source attribution studies for Campylobacter use subtyping data based on single isolates from foods and environmental sources in an attempt to draw epidemiological inferences. It has been suggested that subtyping only one Campylobacter isolate per chicken carcass incurs a risk of failing to recognise the presence of clinically relevant, but numerically infrequent, subtypes. To investigate this, between 21 and 25 Campylobacter jejuni isolates from each of ten retail chicken carcasses were subtyped by pulsed-field gel electrophoresis (PFGE using the two restriction enzymes SmaI and KpnI. Among the 227 isolates, thirteen subtypes were identified, the most frequently occurring subtype being isolated from three carcasses. Six carcasses carried a single subtype, three carcasses carried two subtypes each and one carcass carried three subtypes. Some subtypes carried by an individual carcass were shown to be potentially clonally related. Comparison of C. jejuni subtypes from chickens with isolate subtypes from human clinical cases (n = 1248 revealed seven of the thirteen chicken subtypes were indistinguishable from human cases. None of the numerically minor chicken subtypes were identified in the human data. Therefore, typing only one Campylobacter isolate from individual chicken carcasses may be adequate to inform Campylobacter source attribution.

  1. Influence of Nitrogen Source on 2,4-diacetylphloroglucinol Production by the Biocontrol Strain Pf-5

    M, Hultberg; B, Alsanius

    2008-01-01

    The production of 2,4-diacetylphloroglucinol (DAPG) by the biocontrol agent Pseudomonas fluorescens Pf-5 was studied in nutrient-solution based media with varying nitrogen content. No production of DAPG was observed when organic nitrogen was omitted from the media, regardless of the inorganic nitrogen source used. Furthermore, a micromolar concentration range of organic nitrogen was insufficient to sustain production. When a millimolar concentration range of organic nitrogen was used, DAPG pr...

  2. 40 CFR 63.5985 - What are my alternatives for meeting the emission limits for tire production affected sources?

    2010-07-01

    ... the emission limits for tire production affected sources? 63.5985 Section 63.5985 Protection of... Pollutants: Rubber Tire Manufacturing Emission Limits for Tire Production Affected Sources § 63.5985 What are my alternatives for meeting the emission limits for tire production affected sources? You must use...

  3. Design and use of multiple blade slurry sawing in a production atmosphere

    Lynah, F. P., Jr.; Ross, J. B.

    1982-01-01

    The technique and uses of the multiple blade slurry (MBS) saw are considered. Multiple bands of steel are arranged in a frame and the frame is reciprocated with the steel bands to a workpiece, while simultaneously applying abrasive at the point of contact. The blades wear slots in the workpiece and progress through the piece resulting in several parts of wafers. The transition to MBA from diamond slicing is justified by savings resulting from minimized kerf losses, minimized subsurface damage, and improved surface quality off the saw. This allows wafering much closer to finished thickness specifications. The current state of the art MBS technology must be significantly improved if the low cost solar array (LSA) goals are to be attained. It is concluded that although MBS will never be the answer to every wafering requirement, the economical production of wafers to LSA project specifications will be achieved.

  4. Meteorite impacts on ancient oceans opened up multiple NH3 production pathways.

    Shimamura, Kohei; Shimojo, Fuyuki; Nakano, Aiichiro; Tanaka, Shigenori

    2017-05-10

    A recent series of shock experiments by Nakazawa et al. starting in 2005 (e.g. [Nakazawa et al., Earth Planet. Sci. Lett., 2005, 235, 356]) suggested that meteorite impacts on ancient oceans would have yielded a considerable amount of NH 3 to the early Earth from atmospheric N 2 and oceanic H 2 O through reduction by meteoritic iron. To clarify the mechanisms, we imitated the impact events by performing multi-scale shock technique-based ab initio molecular dynamics in the framework of density functional theory in combination with multi-scale shock technique (MSST) simulations. Our previous simulations with impact energies close to that of the experiments revealed picosecond-order rapid NH 3 production during shock compression [Shimamura et al., Sci. Rep., 2016, 6, 38952]. It was also shown that the reduction of N 2 took place with an associative mechanism as seen in the catalysis of nitrogenase enzymes. In this study, we performed an MSST-AIMD simulation to investigate the production by meteorite impacts with higher energies, which are closer to the expected values on the early Earth. It was found that the amount of NH 3 produced further increased. We also found that the increased NH 3 production is due to the emergence of multiple reaction mechanisms at increased impact energies. We elucidated that the reduction of N 2 was not only attributed to the associative mechanism but also to a dissociative mechanism as seen in the Haber-Bosch process and to a mechanism through a hydrazinium ion. The emergence of these multiple production mechanisms capable of providing a large amount of NH 3 would support the suggestions from recent experiments much more strongly than was previously believed, i.e., shock-induced NH 3 production played a key role in the origin of life on Earth.

  5. A modeling study of saltwater intrusion in the Andarax delta area using multiple data sources

    Antonsson, Arni Valur; Engesgaard, Peter Knudegaard; Jorreto, Sara

    context. The validity of a conceptual model is determined by different factors, where both data quantity and quality is of crucial importance. Often, when dealing with saltwater intrusion, data is limited. Therefore, using different sources (and types) of data can be beneficial and increase......In groundwater model development, construction of the conceptual model is one of the (initial and) critical aspects that determines the model reliability and applicability in terms of e.g. system (hydrogeological) understanding, groundwater quality predictions, and general use in water resources...

  6. PSD Applicability Determination for Multiple Owner/Operator Point Sources Within a Single Facility

    This document may be of assistance in applying the New Source Review (NSR) air permitting regulations including the Prevention of Significant Deterioration (PSD) requirements. This document is part of the NSR Policy and Guidance Database. Some documents in the database are a scanned or retyped version of a paper photocopy of the original. Although we have taken considerable effort to quality assure the documents, some may contain typographical errors. Contact the office that issued the document if you need a copy of the original.

  7. Sequential optimization of a terrestrial biosphere model constrained by multiple satellite based products

    Ichii, K.; Kondo, M.; Wang, W.; Hashimoto, H.; Nemani, R. R.

    2012-12-01

    Various satellite-based spatial products such as evapotranspiration (ET) and gross primary productivity (GPP) are now produced by integration of ground and satellite observations. Effective use of these multiple satellite-based products in terrestrial biosphere models is an important step toward better understanding of terrestrial carbon and water cycles. However, due to the complexity of terrestrial biosphere models with large number of model parameters, the application of these spatial data sets in terrestrial biosphere models is difficult. In this study, we established an effective but simple framework to refine a terrestrial biosphere model, Biome-BGC, using multiple satellite-based products as constraints. We tested the framework in the monsoon Asia region covered by AsiaFlux observations. The framework is based on the hierarchical analysis (Wang et al. 2009) with model parameter optimization constrained by satellite-based spatial data. The Biome-BGC model is separated into several tiers to minimize the freedom of model parameter selections and maximize the independency from the whole model. For example, the snow sub-model is first optimized using MODIS snow cover product, followed by soil water sub-model optimized by satellite-based ET (estimated by an empirical upscaling method; Support Vector Regression (SVR) method; Yang et al. 2007), photosynthesis model optimized by satellite-based GPP (based on SVR method), and respiration and residual carbon cycle models optimized by biomass data. As a result of initial assessment, we found that most of default sub-models (e.g. snow, water cycle and carbon cycle) showed large deviations from remote sensing observations. However, these biases were removed by applying the proposed framework. For example, gross primary productivities were initially underestimated in boreal and temperate forest and overestimated in tropical forests. However, the parameter optimization scheme successfully reduced these biases. Our analysis

  8. Estimation of Multiple Point Sources for Linear Fractional Order Systems Using Modulating Functions

    Belkhatir, Zehor

    2017-06-28

    This paper proposes an estimation algorithm for the characterization of multiple point inputs for linear fractional order systems. First, using polynomial modulating functions method and a suitable change of variables the problem of estimating the locations and the amplitudes of a multi-pointwise input is decoupled into two algebraic systems of equations. The first system is nonlinear and solves for the time locations iteratively, whereas the second system is linear and solves for the input’s amplitudes. Second, closed form formulas for both the time location and the amplitude are provided in the particular case of single point input. Finally, numerical examples are given to illustrate the performance of the proposed technique in both noise-free and noisy cases. The joint estimation of pointwise input and fractional differentiation orders is also presented. Furthermore, a discussion on the performance of the proposed algorithm is provided.

  9. Production and Characterization of α-Galactosidase by a Multiple Mutant of Aspergillus niger in Solid-State Fermentation

    Muhammad Siddique Awan

    2009-01-01

    Full Text Available α-Galactosidase is applied in the sugar industry to enhance sugar recovery from sugar beet syrup and to improve nutritional value of the soymilk. In the present investigation, the influence of process variables on the production of this important enzyme has been explored in a newly isolated multiple mutant strain of Aspergillus niger in solid-state fermentation (SSF. Defined fermentation parameters include substrate type (pure lactose and by-products of rice and flour mills as prime substrates, nitrogen source, incubation time, initial pH of the medium and incubation temperature. Extracellular α-galactosidase reached the value of 135.4 IU/g of dry substrate (IU/g after 96 h of fermentation. Supplementation with 2 g of glucose and 3 g of corn steep liquor significantly increased the enzyme production, and maximum value of product yield (318 IU/g by the mutant strain was significantly higher than that reported by the wild type (this work, or other A. niger mutants, recombinants and yeasts reported in literature as producers of elevated levels of α-galactosidase. Among three α-galactosidases, one possessing high subunit molecular mass proteins (99 and 100 kDa has been characterized in both wild and mutant organisms. Thermal properties of the purified enzymes indicate that the mutation decreased the values of activation energy for the formation of enzyme-substrate (ES complex, enthalpy, Gibbs free energy demand for substrate binding, and transition state stabilization. A thermodynamic study of irreversible inactivation of enzymes suggests that the mutant–derived enzyme is more thermostable than the native enzyme, which is attributable to amino acids involved in active catalysis. Because of these properties, the mutant organism is a novel organism and may be exploited for bulk production of thermostable α-galactosidase for the above industrial and nutritional applications.

  10. Effects of different nitrogen sources on the biogas production - a lab-scale investigation.

    Wagner, Andreas Otto; Hohlbrugger, Peter; Lins, Philipp; Illmer, Paul

    2012-12-20

    For anaerobic digestion processes nitrogen sources are poorly investigated although they are known as possible process limiting factors (in the hydrolysis phase) but also as a source for fermentations for subsequent methane production by methanogenic archaea. In the present study different complex and defined nitrogen sources were investigated in a lab-scale experiment in order to study their potential to build up methane. The outcome of the study can be summarised as follows: from complex nitrogen sources yeast extract and casamino acids showed the highest methane production with approximately 600 ml methane per mole of nitrogen, whereas by the use of skim milk no methane production could be observed. From defined nitrogen sources L-arginine showed the highest methane production with almost 1400 ml methane per mole of nitrogen. Moreover it could be demonstrated that the carbon content and therefore C/N-ratio has only minor influence for the methane production from the used substrates. Copyright © 2011 Elsevier GmbH. All rights reserved.

  11. Exploring multiple sources of climatic information within personal and medical diaries, Bombay 1799-1828

    Adamson, George

    2016-04-01

    Private diaries are being recognised as an important source of information on past climatic conditions, providing place-specific, often daily records of meteorological information. As many were not intended for publication, or indeed to be read by anyone other than the author, issues of observer bias are lower than some other types of documentary sources. This paper comprises an exploration of the variety of types of climatic information can be mined from a single document or set of documents. The focus of the analysis is three private and one medical diary kept by British colonists in Bombay, western India, during the first decades of the nineteenth century. The paper discusses the potential of the diaries for reconstruction of precipitation, temperature and extreme events. Ad-hoc temperature observations collected by the four observers prove to be particularly fruitful for reconstructing monthly extreme temperatures, with values comparable to more systematic observations collected during the period. This leads to a tentative conclusion that extreme temperatures in Bombay were around 5°C lower during the period than today, a difference likely predominantly attributable to the urban heat island effect.

  12. Testing the count rate performance of the scintillation camera by exponential attenuation: Decaying source; Multiple filters

    Adams, R.; Mena, I.

    1988-01-01

    An algorithm and two fortrAN programs have been developed to evaluate the count rate performance of scintillation cameras from count rates reduced exponentially, either by a decaying source or by filtration. The first method is used with short-lived radionuclides such as 191 /sup m/Ir or 191 /sup m/Au. The second implements a National Electrical Manufacturers' Association (NEMA) protocol in which the count rate from a source of 191 /sup m/Tc is attenuated by a varying number of copper filters stacked over it. The count rate at each data point is corrected for deadtime loss after assigning an arbitrary deadtime (tau). A second-order polynomial equation is fitted to the logarithms of net count rate values: ln(R) = A+BT+CT 2 where R is the net corrected count rate (cps), and T is the elapsed time (or the filter thickness in the NEMA method). Depending on C, tau is incremented or decremented iteratively, and the count rate corrections and curve fittings are repeated until C approaches zero, indicating a correct value of the deadtime (tau). The program then plots the measured count rate versus the corrected count rate values

  13. Examining Multiple Sources of Differential Item Functioning on the Clinician & Group CAHPS® Survey

    Rodriguez, Hector P; Crane, Paul K

    2011-01-01

    Objective To evaluate psychometric properties of a widely used patient experience survey. Data Sources English-language responses to the Clinician & Group Consumer Assessment of Healthcare Providers and Systems (CG-CAHPS®) survey (n = 12,244) from a 2008 quality improvement initiative involving eight southern California medical groups. Methods We used an iterative hybrid ordinal logistic regression/item response theory differential item functioning (DIF) algorithm to identify items with DIF related to patient sociodemographic characteristics, duration of the physician–patient relationship, number of physician visits, and self-rated physical and mental health. We accounted for all sources of DIF and determined its cumulative impact. Principal Findings The upper end of the CG-CAHPS® performance range is measured with low precision. With sensitive settings, some items were found to have DIF. However, overall DIF impact was negligible, as 0.14 percent of participants had salient DIF impact. Latinos who spoke predominantly English at home had the highest prevalence of salient DIF impact at 0.26 percent. Conclusions The CG-CAHPS® functions similarly across commercially insured respondents from diverse backgrounds. Consequently, previously documented racial and ethnic group differences likely reflect true differences rather than measurement bias. The impact of low precision at the upper end of the scale should be clarified. PMID:22092021

  14. By-products of fruits processing as a source of phytochemicals

    Sonja Djilas

    Full Text Available The processing of fruits results in high amounts of waste materials such as peels, seeds, stones, and oilseed meals. A disposal of these materials usually represents a problem that is further aggravated by legal restrictions. Thus new aspects concerning the use of these wastes as by-products for further exploitation on the production of food additives or supplements with high nutritional value have gained increasing interest because these are high-value products and their recovery may be economically attractive. It is well known that by-products represent an important source of sugars, minerals, organic acid, dietary fibre and phenolics which have a wide range of action which includes antitumoral, antiviral, antibacterial, cardioprotective and antimutagenic activities. This review discusses the potential of the most important by-products of apple, grape and citrus fruits processing as a source of valuable compounds. The relevance of this topic is illustrated by a number of references.

  15. The development of a methodology to assess population doses from multiple sources and exposure pathways of radioactivity

    Hancox, J.; Stansby, S.; Thorne, M.

    2002-01-01

    The Environment Agency (EA) has new duties in accordance with the Basic Safety Standards Directive under which it is required to ensure that doses to individuals received from exposure to anthropogenic sources of radioactivity are within defined limits. In order to assess compliance with these requirements, the EA needs to assess the doses to members of the most highly exposed population groups ('critical' groups) from all relevant potential sources of anthropogenic radioactivity and all relevant potential exposure pathways to such radioactivity. The EA has identified a need to develop a methodology for the retrospective assessment of effective doses from multiple sources of radioactive materials and exposure pathways associated with those sources. Under contract to the EA, AEA Technology has undertaken the development of a suitable methodology as part of EA R and D Project P3-070. The methodology developed under this research project has been designed to support the EA in meeting its obligations under the Euratom Basic Safety Standards Directive and is consistent with UK and international approaches to radiation dosimetry and radiological protection. The development and trial application of the methodology is described in this report

  16. Elucidating the contributions of multiple aldehyde/alcohol dehydrogenases to butanol and ethanol production in Clostridium acetobutylicum

    Dai, Zongjie; Dong, Hongjun; Zhang, Yanping; Li, Yin

    2016-01-01

    Ethanol and butanol biosynthesis in Clostridium acetobutylicum share common aldehyde/alcohol dehydrogenases. However, little is known about the relative contributions of these multiple dehydrogenases to ethanol and butanol production respectively. The contributions of six aldehyde/alcohol dehydrogenases of C. acetobutylicum on butanol and ethanol production were evaluated through inactivation of the corresponding genes respectively. For butanol production, the relative contributions from thes...

  17. Relationship between availability of contraceptive products and pharmacists as information sources.

    Cook, Elizabeth A; Farris, Karen B; Chrischilles, Elizabeth; Aquilino, Mary

    2012-01-01

    To describe the relationship between the availability and accessibility of contraceptives in Iowa pharmacies and the extent to which pharmacists act as an information source regarding contraceptives. Descriptive, exploratory, nonexperimental study. Iowa in fall 2008. 282 pharmacists at Iowa community pharmacies. Cross-sectional survey. Contraceptive availability score, contraceptive accessibility score, and total access score. Regression analyses tested the relationships between the pharmacist information source score and the contraceptive availability, accessibility, and total access scores, controlling for geography, ownership, staff size, and average number of prescriptions per day. Significant positive relationships between the pharmacist information source score and product accessibility, product availability, and total access were observed. The relationship appeared to be driven primarily by product availability, and all were significantly influenced by pharmacy type. Significant negative relationships were found between product accessibility and independent/small chain pharmacies and mass merchandiser/grocery store pharmacies relative to large chain pharmacies. A significant negative relationship was found between independent/small chain pharmacies and the product availability score. Significant relationships were found between pharmacists' ability to act as sources of information for contraceptive products and the availability, accessibility, and overall access to contraceptives in the pharmacy.

  18. Entropy production and multiple equilibria: the case of the ice-albedo feedback

    C. Herbert

    2011-02-01

    Full Text Available Nonlinear feedbacks in the Earth System provide mechanisms that can prove very useful in understanding complex dynamics with relatively simple concepts. For example, the temperature and the ice cover of the planet are linked in a positive feedback which gives birth to multiple equilibria for some values of the solar constant: fully ice-covered Earth, ice-free Earth and an intermediate unstable solution. In this study, we show an analogy between a classical dynamical system approach to this problem and a Maximum Entropy Production (MEP principle view, and we suggest a glimpse on how to reconcile MEP with the time evolution of a variable. It enables us in particular to resolve the question of the stability of the entropy production maxima. We also compare the surface heat flux obtained with MEP and with the bulk-aerodynamic formula.

  19. Multiple energy supply risks, optimal reserves, and optimal domestic production capacities

    Zweifel, P.; Ferrari, M.

    1992-01-01

    This study starts from the observation that today's Western trading nations are exposed to multiple risks of energy supplies, e.g. simultaneous shortage of oil and electricity supplies. To cope with these risks, oil can be stockpiled as well as domestic capacity for power production built up. Adopting the viewpoint of a policy maker who aims at minimizing the expected cost of security of supply, optimal simultaneous adjustments of oil stocks and electric production capacities to exogenous changes such as economic growth are derived. Against this benchmark, one-dimensional rules such as 'oil reserves for 90 days' turn out to be not only suboptimal but also to foster adjustments that exacerbate suboptimality. 9 refs., 1 tabs

  20. A Multiple Source Approach to Organisational Justice: The Role of the Organisation, Supervisors, Coworkers, and Customers

    Agustin Molina

    2015-07-01

    Full Text Available The vast research on organisational justice has focused on the organisation and the supervisor. This study aims to further this line of research by integrating two trends within organisational justice research: the overall approach to justice perceptions and the multifoci perspective of justice judgments. Specifically, this study aims to explore the effects of two additional sources of justice, coworker-focused justice and customer-focused justice, on relevant employees’ outcomes—burnout, turnover intentions, job satisfaction, and workplace deviance— while controlling the effect of organisation-focused justice and supervisor-focused justice. Given the increased importance attributed to coworkers and customers, we expect coworker-focused justice and customer-focused justice to explain incremental variance in the measured outcomes, above and beyond the effects of organisation-focused justice and supervisor-focused justice. Participants will be university students from Austria and Germany employed by service organisations. Data analysis will be conducted using structural equation modeling.

  1. Evidence for multiple sources of 10Be in the early solar system

    Wielandt, Daniel Kim Peel; Nagashima, Kazuhide; Krot, Alexander N.

    2012-01-01

    Beryllium-10 is a short-lived radionuclide (t 1/2 = 1.4 Myr) uniquely synthesized by spallation reactions and inferred to have been present when the solar system's oldest solids (calcium-aluminum-rich inclusions, CAIs) formed. Yet, the astrophysical site of 10Be nucleosynthesis is uncertain. We...... in the gaseous CAI-forming reservoir, or in the inclusions themselves: this indicates at least two nucleosynthetic sources of 10Be in the early solar system. The most promising locale for 10Be synthesis is close to the proto-Sun during its early mass-accreting stages, as these are thought to coincide...

  2. Deterministic approach for multiple-source tsunami hazard assessment for Sines, Portugal

    Wronna, M.; Omira, R.; Baptista, M. A.

    2015-11-01

    In this paper, we present a deterministic approach to tsunami hazard assessment for the city and harbour of Sines, Portugal, one of the test sites of project ASTARTE (Assessment, STrategy And Risk Reduction for Tsunamis in Europe). Sines has one of the most important deep-water ports, which has oil-bearing, petrochemical, liquid-bulk, coal, and container terminals. The port and its industrial infrastructures face the ocean southwest towards the main seismogenic sources. This work considers two different seismic zones: the Southwest Iberian Margin and the Gloria Fault. Within these two regions, we selected a total of six scenarios to assess the tsunami impact at the test site. The tsunami simulations are computed using NSWING, a Non-linear Shallow Water model wIth Nested Grids. In this study, the static effect of tides is analysed for three different tidal stages: MLLW (mean lower low water), MSL (mean sea level), and MHHW (mean higher high water). For each scenario, the tsunami hazard is described by maximum values of wave height, flow depth, drawback, maximum inundation area and run-up. Synthetic waveforms are computed at virtual tide gauges at specific locations outside and inside the harbour. The final results describe the impact at the Sines test site considering the single scenarios at mean sea level, the aggregate scenario, and the influence of the tide on the aggregate scenario. The results confirm the composite source of Horseshoe and Marques de Pombal faults as the worst-case scenario, with wave heights of over 10 m, which reach the coast approximately 22 min after the rupture. It dominates the aggregate scenario by about 60 % of the impact area at the test site, considering maximum wave height and maximum flow depth. The HSMPF scenario inundates a total area of 3.5 km2.

  3. High-current negative hydrogen ion beam production in a cesium-injected multicusp source

    Takeiri, Y.; Tsumori, K.; Kaneko, O.

    1997-01-01

    A high-current negative hydrogen ion source has been developed, where 16.2 A of the H - current was obtained with a current density of 31 mA/cm 2 . The ion source is a multicusp source with a magnetic filter for negative ion production, and cesium vapor is injected into the arc chamber, leading to enhancement of the negative ion yields. The cesium-injection effects are discussed, based on the experimental observations. Although the surface production of the negative ions on the cesium-covered plasma grid is thought to be a dominant mechanism of the H - current enhancement, the cesium effects in the plasma volume, such as the cesium ionization and the electron cooling, are observed, and could contribute to the improved operation of the negative ion source. (author)

  4. Efficient source for the production of ultradense deuterium D(-1) for laser-induced fusion (ICF)

    Andersson, Patrik U.; Loenn, Benny; Holmlid, Leif

    2011-01-01

    A novel source which simplifies the study of ultradense deuterium D(-1) is now described. This means one step further toward deuterium fusion energy production. The source uses internal gas feed and D(-1) can now be studied without time-of-flight spectral overlap from the related dense phase D(1). The main aim here is to understand the material production parameters, and thus a relatively weak laser with focused intensity ≤10 12 W cm -2 is employed for analyzing the D(-1) material. The properties of the D(-1) material at the source are studied as a function of laser focus position outside the emitter, deuterium gas feed, laser pulse repetition frequency and laser power, and temperature of the source. These parameters influence the D(-1) cluster size, the ionization mode, and the laser fragmentation patterns.

  5. Efficient source for the production of ultradense deuterium D(-1) for laser-induced fusion (ICF)

    Andersson, Patrik U.; Lönn, Benny; Holmlid, Leif

    2011-01-01

    A novel source which simplifies the study of ultradense deuterium D(-1) is now described. This means one step further toward deuterium fusion energy production. The source uses internal gas feed and D(-1) can now be studied without time-of-flight spectral overlap from the related dense phase D(1). The main aim here is to understand the material production parameters, and thus a relatively weak laser with focused intensity ≤1012 W cm-2 is employed for analyzing the D(-1) material. The properties of the D(-1) material at the source are studied as a function of laser focus position outside the emitter, deuterium gas feed, laser pulse repetition frequency and laser power, and temperature of the source. These parameters influence the D(-1) cluster size, the ionization mode, and the laser fragmentation patterns.

  6. Bayesian inference based modelling for gene transcriptional dynamics by integrating multiple source of knowledge

    Wang Shu-Qiang

    2012-07-01

    Full Text Available Abstract Background A key challenge in the post genome era is to identify genome-wide transcriptional regulatory networks, which specify the interactions between transcription factors and their target genes. Numerous methods have been developed for reconstructing gene regulatory networks from expression data. However, most of them are based on coarse grained qualitative models, and cannot provide a quantitative view of regulatory systems. Results A binding affinity based regulatory model is proposed to quantify the transcriptional regulatory network. Multiple quantities, including binding affinity and the activity level of transcription factor (TF are incorporated into a general learning model. The sequence features of the promoter and the possible occupancy of nucleosomes are exploited to estimate the binding probability of regulators. Comparing with the previous models that only employ microarray data, the proposed model can bridge the gap between the relative background frequency of the observed nucleotide and the gene's transcription rate. Conclusions We testify the proposed approach on two real-world microarray datasets. Experimental results show that the proposed model can effectively identify the parameters and the activity level of TF. Moreover, the kinetic parameters introduced in the proposed model can reveal more biological sense than previous models can do.

  7. In-Situ Ion Source Cleaning: Review of Chemical Mechanisms and Evaluation Data at Production Fabs

    Kaim, R.; Bishop, S.; Byl, O.; Eldridge, D.; Marganski, P.; Mayer, J.; Sweeney, J.; Yedave, S.; Fuchs, D.; Spreitzer, S.; Vogel, J.; Dunn, J.; Lundquist, P.; Rolland, J.; Romig, T.; Newman, D.; Mitchell, M.; Ditzler, K.

    2008-01-01

    Since the concept of chemical in-situ ion implanter cleaning was introduced at IIT2006 [1], evaluations of the XeF 2 cleaning technology have taken place or are ongoing at more than 40 production fabs worldwide. Testing has been focused on assessing effects of cleaning in the source arc chamber and extraction regions. In this paper we describe use of the cleaning technology in a production environment and summarize evaluation data showing advantages of the technology for improving ion source life, reducing glitching, improving beam auto-tuning and avoiding species cross-contamination. More details of the evaluations are given in several separate papers submitted to this Conference. We have supplemented the fab production data with laboratory experiments designed to investigate the reactivity of XeF 2 and fundamental aspects of the source deposition and cleaning processes. These experiments are summarized here, and more details can be found in separate papers submitted to this Conference

  8. Application of the Modified Source Multiplication (MSM) technique to subcritical reactivity worth measurements in thermal and fast reactor systems

    Blaise, P.; Fougeras, P.; Mellier, F.

    2009-01-01

    The Amplified Source Multiplication (ASM) method and its improved Modified Source Multiplication (MSM) method have been widely used in the CEA's EOLE and MASURCA critical facilities over the past decades for the determination of reactivity worths by using fission chambers in subcritical configurations. They have been successfully applied to absorber (single or clusters) worth measurement in both thermal and fast spectra, or for (sodium or water) void reactivity worths. The ASM methodology, which is the basic technique to estimate a reactivity worth, uses relatively simple relationships between count rates of efficient miniature fission chambers located in slightly subcritical reference and perturbed configurations. If this method works quite well for small reactivity variation (a few effective delayed neutron fraction), its raw results needs to be corrected to take into account the flux perturbation in the fission chamber. This is performed by applying to the measurement a correction factor called MSM. Its characteristics is to take into account the local space and energy variation of the spectrum in the fission chamber, through standard perturbation theory applied to neutron transport calculation in the perturbed configuration. The proposed paper describes in details both methodologies, with their associated uncertainties. Applications on absorber cluster worth in the MISTRAL-4 full MOX mock-up core and the last core loaded in MASURCA show the importance of the MSM correction on raw data. (authors)

  9. The Potential for Electrofuels Production in Sweden Utilizing Fossil and Biogenic CO2 Point Sources

    Hansson, Julia; Hackl, Roman; Taljegard, Maria; Brynolf, Selma; Grahn, Maria

    2017-01-01

    This paper maps, categorizes, and quantifies all major point sources of carbon dioxide (CO 2 ) emissions from industrial and combustion processes in Sweden. The paper also estimates the Swedish technical potential for electrofuels (power-to-gas/fuels) based on carbon capture and utilization. With our bottom-up approach using European databases, we find that Sweden emits approximately 50 million metric tons of CO 2 per year from different types of point sources, with 65% (or about 32 million tons) from biogenic sources. The major sources are the pulp and paper industry (46%), heat and power production (23%), and waste treatment and incineration (8%). Most of the CO 2 is emitted at low concentrations (<15%) from sources in the southern part of Sweden where power demand generally exceeds in-region supply. The potentially recoverable emissions from all the included point sources amount to 45 million tons. If all the recoverable CO 2 were used to produce electrofuels, the yield would correspond to 2–3 times the current Swedish demand for transportation fuels. The electricity required would correspond to about 3 times the current Swedish electricity supply. The current relatively few emission sources with high concentrations of CO 2 (>90%, biofuel operations) would yield electrofuels corresponding to approximately 2% of the current demand for transportation fuels (corresponding to 1.5–2 TWh/year). In a 2030 scenario with large-scale biofuels operations based on lignocellulosic feedstocks, the potential for electrofuels production from high-concentration sources increases to 8–11 TWh/year. Finally, renewable electricity and production costs, rather than CO 2 supply, limit the potential for production of electrofuels in Sweden.

  10. Best practices for International eSourcing of Software Products and Services

    Käkölä, Timo

    2008-01-01

    This paper analyzes how the information and communications technology-supported international eSourcing of software products and services (IeS) can be effectively executed. The extant literature falls short of providing a systematic and detailed enough set of best practices to guide IeS. This paper presents best practices for IeS to facilitate further research, and to help managers and other stakeholders to understand, execute, and proactively improve and manage international eSourcing. The p...

  11. Detecting and accounting for multiple sources of positional variance in peak list registration analysis and spin system grouping.

    Smelter, Andrey; Rouchka, Eric C; Moseley, Hunter N B

    2017-08-01

    Peak lists derived from nuclear magnetic resonance (NMR) spectra are commonly used as input data for a variety of computer assisted and automated analyses. These include automated protein resonance assignment and protein structure calculation software tools. Prior to these analyses, peak lists must be aligned to each other and sets of related peaks must be grouped based on common chemical shift dimensions. Even when programs can perform peak grouping, they require the user to provide uniform match tolerances or use default values. However, peak grouping is further complicated by multiple sources of variance in peak position limiting the effectiveness of grouping methods that utilize uniform match tolerances. In addition, no method currently exists for deriving peak positional variances from single peak lists for grouping peaks into spin systems, i.e. spin system grouping within a single peak list. Therefore, we developed a complementary pair of peak list registration analysis and spin system grouping algorithms designed to overcome these limitations. We have implemented these algorithms into an approach that can identify multiple dimension-specific positional variances that exist in a single peak list and group peaks from a single peak list into spin systems. The resulting software tools generate a variety of useful statistics on both a single peak list and pairwise peak list alignment, especially for quality assessment of peak list datasets. We used a range of low and high quality experimental solution NMR and solid-state NMR peak lists to assess performance of our registration analysis and grouping algorithms. Analyses show that an algorithm using a single iteration and uniform match tolerances approach is only able to recover from 50 to 80% of the spin systems due to the presence of multiple sources of variance. Our algorithm recovers additional spin systems by reevaluating match tolerances in multiple iterations. To facilitate evaluation of the

  12. Production of Multiple Growth Factors by a Newly Established Human Thyroid Carcinoma Cell Line

    Yoshida, Yataro; Ohashi, Kensaku; Sano, Emiko; Kobayashi, Hisataka; Endo, Keigo; Naruto, Masanobu; Nakamura, Toru

    1992-01-01

    A multiple growth factor‐producing tumor cell line (NIM‐1) was newly established from a patient with thyroid cancer and remarkable neutrophilia. NIM‐1 cells also caused severe neutrophilia in nude mice bearing tumors. NIM‐1‐conditioned medium (NIM‐1CM) contained activities that supported not only granulocyte, macrophage and eosinophil colony formation of human bone marrow cells but also the growth of colony‐stimulating factor (CSF)‐dependent cell lines, NFS60‐KX and TF‐1. Northern blot hybridization analysis revealed the constitutive expression of granulocyte‐CSF (G‐CSF), granulocyte/macrophage‐CSF (GM‐CSF) and interleukin(IL)‐6 mRNAs in NIM‐1 cells. Enzyme‐linked immunosorbent assays (ELISA) using NIM‐1CM also confirmed the production of IL‐la and a small amount of IL‐1β besides G‐CSF, GM‐CSF and IL‐6 in NIM‐1 cells. In addition, unexpected production of IL‐11 in NIM‐1 cells was detected by northern blot hybridization analysis and by bioassay using an IL‐11‐dependent cell line. Therefore, NIM‐1 cell line is shown to produce multiple cytokines including potentially megakaryopoietic growth factors such as GM‐CSF, IL‐6 and IL‐11. PMID:1372885

  13. Companion Animals as a Source of Viruses for Human Beings and Food Production Animals.

    Reperant, L A; Brown, I H; Haenen, O L; de Jong, M D; Osterhaus, A D M E; Papa, A; Rimstad, E; Valarcher, J-F; Kuiken, T

    2016-07-01

    Companion animals comprise a wide variety of species, including dogs, cats, horses, ferrets, guinea pigs, reptiles, birds and ornamental fish, as well as food production animal species, such as domestic pigs, kept as companion animals. Despite their prominent place in human society, little is known about the role of companion animals as sources of viruses for people and food production animals. Therefore, we reviewed the literature for accounts of infections of companion animals by zoonotic viruses and viruses of food production animals, and prioritized these viruses in terms of human health and economic importance. In total, 138 virus species reportedly capable of infecting companion animals were of concern for human and food production animal health: 59 of these viruses were infectious for human beings, 135 were infectious for food production mammals and birds, and 22 were infectious for food production fishes. Viruses of highest concern for human health included hantaviruses, Tahyna virus, rabies virus, West Nile virus, tick-borne encephalitis virus, Crimean-Congo haemorrhagic fever virus, Aichi virus, European bat lyssavirus, hepatitis E virus, cowpox virus, G5 rotavirus, influenza A virus and lymphocytic choriomeningitis virus. Viruses of highest concern for food production mammals and birds included bluetongue virus, African swine fever virus, foot-and-mouth disease virus, lumpy skin disease virus, Rift Valley fever virus, porcine circovirus, classical swine fever virus, equine herpesvirus 9, peste des petits ruminants virus and equine infectious anaemia virus. Viruses of highest concern for food production fishes included cyprinid herpesvirus 3 (koi herpesvirus), viral haemorrhagic septicaemia virus and infectious pancreatic necrosis virus. Of particular concern as sources of zoonotic or food production animal viruses were domestic carnivores, rodents and food production animals kept as companion animals. The current list of viruses provides an objective

  14. Examining relationships between multiple health risk behaviors, well-being, and productivity.

    Evers, Kerry E; Castle, Patricia H; Prochaska, James O; Prochaska, Janice M

    2014-06-01

    Traditionally, the concept of health promotion has emphasized the reduction of health risk behaviors to reduce disease and impairment. Well-being research expands this focus to include positive constructs such as thriving, productivity, life-evaluation, and emotional and physical health. The objective of the present study was to examine the relationships between health risk behaviors and specific measures of individual well-being. Participants (N = 790) from 49 states completed a one-time online assessment that included the Life-Evaluation Index, Emotional and Physical Health Ladders, the Health Risk Intervention Assessment, and the Work Productivity and Activity Improvement Questionnaire for General Health. Life Evaluation and physical and emotional health were all inversely related to the number of health risk behaviors, with higher well-being scores associated with lower number of risk behaviors. Across the three Life Evaluation categories (Suffering, Struggling, and Thriving) the number of health risk behaviors decreased, productivity loss decreased, and emotional and physical health increased. The results add to previous research on how reducing multiple health risk behaviors can be combined with well-being, i.e., an emphasis on increasing life-evaluation, emotional and physical health, better functioning, and productivity.

  15. Comparing costs of power and heat production by prospective and present sources

    Novak, S.

    1979-01-01

    Capital and running costs are compared of power and heat production from different sources. The lowest capital costs were found for coal-fired power plants followed by light water reactor power plants. The capital costs of other types of power plants, such as wind, geothermal, solar, thermonuclear power plants are significantly higher. The estimated specific cost for electric power production in 1985 for a nuclear power plant is lower than for a fossil-fuel power plant. It is estimated that in 1985 coal will be the cheapest heat source. (Ha)

  16. Scenario based approach for multiple source Tsunami Hazard assessment for Sines, Portugal

    Wronna, M.; Omira, R.; Baptista, M. A.

    2015-08-01

    In this paper, we present a scenario-based approach for tsunami hazard assessment for the city and harbour of Sines - Portugal, one of the test-sites of project ASTARTE. Sines holds one of the most important deep-water ports which contains oil-bearing, petrochemical, liquid bulk, coal and container terminals. The port and its industrial infrastructures are facing the ocean southwest towards the main seismogenic sources. This work considers two different seismic zones: the Southwest Iberian Margin and the Gloria Fault. Within these two regions, we selected a total of six scenarios to assess the tsunami impact at the test site. The tsunami simulations are computed using NSWING a Non-linear Shallow Water Model With Nested Grids. In this study, the static effect of tides is analysed for three different tidal stages MLLW (mean lower low water), MSL (mean sea level) and MHHW (mean higher high water). For each scenario, inundation is described by maximum values of wave height, flow depth, drawback, runup and inundation distance. Synthetic waveforms are computed at virtual tide gauges at specific locations outside and inside the harbour. The final results describe the impact at Sines test site considering the single scenarios at mean sea level, the aggregate scenario and the influence of the tide on the aggregate scenario. The results confirm the composite of Horseshoe and Marques Pombal fault as the worst case scenario. It governs the aggregate scenario with about 60 % and inundates an area of 3.5 km2.

  17. IPeak: An open source tool to combine results from multiple MS/MS search engines.

    Wen, Bo; Du, Chaoqin; Li, Guilin; Ghali, Fawaz; Jones, Andrew R; Käll, Lukas; Xu, Shaohang; Zhou, Ruo; Ren, Zhe; Feng, Qiang; Xu, Xun; Wang, Jun

    2015-09-01

    Liquid chromatography coupled tandem mass spectrometry (LC-MS/MS) is an important technique for detecting peptides in proteomics studies. Here, we present an open source software tool, termed IPeak, a peptide identification pipeline that is designed to combine the Percolator post-processing algorithm and multi-search strategy to enhance the sensitivity of peptide identifications without compromising accuracy. IPeak provides a graphical user interface (GUI) as well as a command-line interface, which is implemented in JAVA and can work on all three major operating system platforms: Windows, Linux/Unix and OS X. IPeak has been designed to work with the mzIdentML standard from the Proteomics Standards Initiative (PSI) as an input and output, and also been fully integrated into the associated mzidLibrary project, providing access to the overall pipeline, as well as modules for calling Percolator on individual search engine result files. The integration thus enables IPeak (and Percolator) to be used in conjunction with any software packages implementing the mzIdentML data standard. IPeak is freely available and can be downloaded under an Apache 2.0 license at https://code.google.com/p/mzidentml-lib/. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  18. Exploiting multiple sources of information in learning an artificial language: human data and modeling.

    Perruchet, Pierre; Tillmann, Barbara

    2010-03-01

    This study investigates the joint influences of three factors on the discovery of new word-like units in a continuous artificial speech stream: the statistical structure of the ongoing input, the initial word-likeness of parts of the speech flow, and the contextual information provided by the earlier emergence of other word-like units. Results of an experiment conducted with adult participants show that these sources of information have strong and interactive influences on word discovery. The authors then examine the ability of different models of word segmentation to account for these results. PARSER (Perruchet & Vinter, 1998) is compared to the view that word segmentation relies on the exploitation of transitional probabilities between successive syllables, and with the models based on the Minimum Description Length principle, such as INCDROP. The authors submit arguments suggesting that PARSER has the advantage of accounting for the whole pattern of data without ad-hoc modifications, while relying exclusively on general-purpose learning principles. This study strengthens the growing notion that nonspecific cognitive processes, mainly based on associative learning and memory principles, are able to account for a larger part of early language acquisition than previously assumed. Copyright © 2009 Cognitive Science Society, Inc.

  19. Influence of nitrogen sources on amino acid production by aspergillus niger

    Almani, F.; Dahot, M.U.

    2007-01-01

    The effect of different organic and inorganic nitrogen sources in 0.1% and 0.2% concentration on the production of amino acid was studied using a wild strain of Aspergillus niger. The rate of amino acid biosynthesis was found to be higher when 0.2% corn steep liquor was incorporated in the mineral medium. It was concluded from the study that the amino acid synthesis by wild strain depends not only on the nature and type of nitrogen sources used but the concentration of nitrogen source also play an important in the accumulation of free amino acids in the medium. (author)

  20. The influence of various carbon and nitrogen sources on oil production by Fusarium oxysporum.

    Joshi, S; Mathur, J M

    1987-01-01

    The oil-synthesizing capacity of Fusarium oxysporum, cultivated on basal nutrient medium, was evaluated using different carbon and nitrogen sources. In one of the media, molasses was also used as a principal carbon source. Media containing glucose and ammonium nitrate were found to be most efficient for oil production. Fatty acid profile of the fungal oil indicated the presence of a wide range of fatty acids ranging from C8 to C24. Fatty acid composition largely depends on the type of carbon and nitrogen sources.

  1. Potential of chicken by-products as sources of useful biological resources

    Lasekan, Adeseye; Abu Bakar, Fatimah; Hashim, Dzulkifly

    2013-01-01

    By-products from different animal sources are currently being utilised for beneficial purposes. Chicken processing plants all over the world generate large amount of solid by-products in form of heads, legs, bones, viscera and feather. These wastes are often processed into livestock feed, fertilizers and pet foods or totally discarded. Inappropriate disposal of these wastes causes environmental pollution, diseases and loss of useful biological resources like protein, enzymes and lipids. Utilisation methods that make use of these biological components for producing value added products rather than the direct use of the actual waste material might be another viable option for dealing with these wastes. This line of thought has consequently led to researches on these wastes as sources of protein hydrolysates, enzymes and polyunsaturated fatty acids. Due to the multi-applications of protein hydrolysates in various branches of science and industry, and the large body of literature reporting the conversion of animal wastes to hydrolysates, a large section of this review was devoted to this subject. Thus, this review reports the known functional and bioactive properties of hydrolysates derived from chicken by-products as well their utilisation as source of peptone in microbiological media. Methods of producing these hydrolysates including their microbiological safety are discussed. Based on the few references available in the literature, the potential of some chicken by-product as sources of proteases and polyunsaturated fatty acids are pointed out along with some other future applications

  2. Biomass and pigments production in photosynthetic bacteria wastewater treatment: effects of light sources.

    Zhou, Qin; Zhang, Panyue; Zhang, Guangming

    2015-03-01

    This study is aimed at enhancing biomass and pigments production together with pollution removal in photosynthetic bacteria (PSB) wastewater treatment via different light sources. Red, yellow, blue, white LED and incandescent lamp were used. Results showed different light sources had great effects on the PSB. PSB had the highest biomass production, COD removal and biomass yield with red LED. The corresponding biomass, COD removal and biomass yield reached 2580 mg/L, 88.6% and 0.49 mg-biomass/mg-COD-removal, respectively. The hydraulic retention time of wastewater treatment could be shortened to 72 h with red LED. Mechanism analysis showed higher ATP was produced with red LED than others. Light sources could significantly affect the pigments production. The pigments productions were greatly higher with LED than incandescent lamp. Yellow LED had the highest pigments production while red LED produced the highest carotenoid/bacteriochlorophyll ratio. Considering both efficiency and energy cost, red LED was the optimal light source. Copyright © 2014 Elsevier Ltd. All rights reserved.

  3. Sources of New Life Insurance Product Ideas in LIC of India

    Furquan Uddin

    2018-06-01

    Full Text Available The present complex nature of market has created sturdy challenges before the business world in the form of designing right product, right price, right placement and right promotion. In order to survive and thrive, a marketer has to focus on these challenges. Amongst, right product is most crucial which requires good and feasible ideas in all industries including life insurance. In fact, life insurance is perceived as an unsought and complicated financial product in India. The present paper is a humble attempt to examine the sources of new life insurance product ideas in LIC of India. The findings of the present study include the sources into six groups such as key stakeholders, workforce, organizational documents and other sources, research unit, competitors, and national and international source. It may be noticed the key stakeholders like Insurance Regulatory and Development Authority of India, actuary, top management, and policyholders play vital role in providing ideas in the new product development process of LIC of India.

  4. Potential of chicken by-products as sources of useful biological resources

    Lasekan, Adeseye [Faculty of Food Science and Technology, Universiti Putra Malaysia, 43400 UPM Serdang, Selangor (Malaysia); Abu Bakar, Fatimah, E-mail: fatim@putra.upm.edu.my [Faculty of Food Science and Technology, Universiti Putra Malaysia, 43400 UPM Serdang, Selangor (Malaysia); Halal Products Research Institute, Universiti Putra Malaysia, 43400 UPM Serdang, Selangor (Malaysia); Hashim, Dzulkifly [Faculty of Food Science and Technology, Universiti Putra Malaysia, 43400 UPM Serdang, Selangor (Malaysia); Halal Products Research Institute, Universiti Putra Malaysia, 43400 UPM Serdang, Selangor (Malaysia)

    2013-03-15

    By-products from different animal sources are currently being utilised for beneficial purposes. Chicken processing plants all over the world generate large amount of solid by-products in form of heads, legs, bones, viscera and feather. These wastes are often processed into livestock feed, fertilizers and pet foods or totally discarded. Inappropriate disposal of these wastes causes environmental pollution, diseases and loss of useful biological resources like protein, enzymes and lipids. Utilisation methods that make use of these biological components for producing value added products rather than the direct use of the actual waste material might be another viable option for dealing with these wastes. This line of thought has consequently led to researches on these wastes as sources of protein hydrolysates, enzymes and polyunsaturated fatty acids. Due to the multi-applications of protein hydrolysates in various branches of science and industry, and the large body of literature reporting the conversion of animal wastes to hydrolysates, a large section of this review was devoted to this subject. Thus, this review reports the known functional and bioactive properties of hydrolysates derived from chicken by-products as well their utilisation as source of peptone in microbiological media. Methods of producing these hydrolysates including their microbiological safety are discussed. Based on the few references available in the literature, the potential of some chicken by-product as sources of proteases and polyunsaturated fatty acids are pointed out along with some other future applications.

  5. Upgrading of citric acid production from cheap carbohydrate sources as affected by aspergillus

    Elbatal, A.I.; Khalaf, S.A.; Khalil, A.H.

    1995-01-01

    Five strains of aspergillus niger (EMCC 102, EMCC 104, EMCC 111, EMCC 132 and EMCC 147) were for citric acid production at different incubation period using different cheap carbohydrate substrates, such as beet, cane and citrus molasses and milk whey. A. niger EMCC 111 was found to be the most potent strain for citric acid production from beet molasses after 11 days of incubation at 30 degree. The studies concerning molasses concentration and nitrogen sources (inorganic and organic sources with different concentration, revealed that 30 g% beet molasses and ammonium sulfate with 0.05 g% as N 2 content, gave the highest production of citric acid. Gamma irradiated inocula of A. niger EMCC 111 at doses (0.05-0.8 KGy), showed that the dose 0.4 KGy was the optimum for maximum citric acid production. 8 tabs

  6. Influence of carbon source on alpha-amylase production by Aspergillus oryzae

    Carlsen, Morten; Nielsen, Jens

    2001-01-01

    on sucrose, fructose, glycerol, mannitol and acetate. During growth on acetate there was no production of alpha -amylase, whereas addition of small amounts of glucose resulted in alpha -amylase production. A possible induction by alpha -methyl-D-glucoside during growth on glucose was also investigated......, but this compound was not found to be a better inducer of alpha -amylase production than glucose. The results strongly indicate that besides acting as a repressor via the CreA protein, glucose acts as an inducer.......The influence of the carbon source on a-amylase production by Aspergillus oryzae was quantified in carbon-limited chemostat cultures. The following carbon sources were investigated: maltose, maltodextrin (different chain lengths), glucose, fructose, galactose, sucrose, glycerol, mannitol...

  7. Interrogating pollution sources in a mangrove food web using multiple stable isotopes.

    Souza, Iara da C; Arrivabene, Hiulana P; Craig, Carol-Ann; Midwood, Andrew J; Thornton, Barry; Matsumoto, Silvia T; Elliott, Michael; Wunderlin, Daniel A; Monferrán, Magdalena V; Fernandes, Marisa N

    2018-06-01

    Anthropogenic activities including metal contamination create well-known problems in coastal mangrove ecosystems but understanding and linking specific pollution sources to distinct trophic levels within these environments is challenging. This study evaluated anthropogenic impacts on two contrasting mangrove food webs, by using stable isotopes (δ 13 C, δ 15 N, 87 Sr/ 86 Sr, 206 Pb/ 207 Pb and 208 Pb/ 207 Pb) measured in sediments, mangrove trees (Rhizophora mangle, Laguncularia racemosa, Avicennia schaueriana), plankton, shrimps (Macrobranchium sp.), crabs (Aratus sp.), oysters (Crassostrea rhizophorae) and fish (Centropomus parallelus) from both areas. Strontium and Pb isotopes were also analysed in water and atmospheric particulate matter (PM). δ 15 N indicated that crab, shrimp and oyster are at intermediate levels within the local food web and fish, in this case C. parallelus, was confirmed at the highest trophic level. δ 15 N also indicates different anthropogenic pressures between both estuaries; Vitória Bay, close to intensive human activities, showed higher δ 15 N across the food web, apparently influenced by sewage. The ratio 87 Sr/ 86 Sr showed the primary influence of marine water throughout the entire food web. Pb isotope ratios suggest that PM is primarily influenced by metallurgical activities, with some secondary influence on mangrove plants and crabs sampled in the area adjacent to the smelting works. To our knowledge, this is the first demonstration of the effect of anthropogenic pollution (probable sewage pollution) on the isotopic fingerprint of estuarine-mangrove systems located close to a city compared to less impacted estuarine mangroves. The influence of industrial metallurgical activity detected using Pb isotopic analysis of PM and mangrove plants close to such an impacted area is also notable and illustrates the value of isotopic analysis in tracing the impact and species affected by atmospheric pollution. Copyright © 2018 Elsevier B

  8. EVIDENCE FOR MULTIPLE SOURCES OF 10Be IN THE EARLY SOLAR SYSTEM

    Wielandt, Daniel; Krot, Alexander N.; Bizzarro, Martin; Nagashima, Kazuhide; Huss, Gary R.; Ivanova, Marina A.

    2012-01-01

    Beryllium-10 is a short-lived radionuclide (t 1/2 = 1.4 Myr) uniquely synthesized by spallation reactions and inferred to have been present when the solar system's oldest solids (calcium-aluminum-rich inclusions, CAIs) formed. Yet, the astrophysical site of 10 Be nucleosynthesis is uncertain. We report Li-Be-B isotope measurements of CAIs from CV chondrites, including CAIs that formed with the canonical 26 Al/ 27 Al ratio of ∼5 × 10 –5 (canonical CAIs) and CAIs with Fractionation and Unidentified Nuclear isotope effects (FUN-CAIs) characterized by 26 Al/ 27 Al ratios much lower than the canonical value. Our measurements demonstrate the presence of four distinct fossil 10 Be/ 9 Be isochrons, lower in the FUN-CAIs than in the canonical CAIs, and variable within these classes. Given that FUN-CAI precursors escaped evaporation-recondensation prior to evaporative melting, we suggest that the 10 Be/ 9 Be ratio recorded by FUN-CAIs represents a baseline level present in presolar material inherited from the protosolar molecular cloud, generated via enhanced trapping of galactic cosmic rays. The higher and possibly variable apparent 10 Be/ 9 Be ratios of canonical CAIs reflect additional spallogenesis, either in the gaseous CAI-forming reservoir, or in the inclusions themselves: this indicates at least two nucleosynthetic sources of 10 Be in the early solar system. The most promising locale for 10 Be synthesis is close to the proto-Sun during its early mass-accreting stages, as these are thought to coincide with periods of intense particle irradiation occurring on timescales significantly shorter than the formation interval of canonical CAIs.

  9. EarthCube Data Discovery Hub: Enhancing, Curating and Finding Data across Multiple Geoscience Data Sources.

    Zaslavsky, I.; Valentine, D.; Richard, S. M.; Gupta, A.; Meier, O.; Peucker-Ehrenbrink, B.; Hudman, G.; Stocks, K. I.; Hsu, L.; Whitenack, T.; Grethe, J. S.; Ozyurt, I. B.

    2017-12-01

    EarthCube Data Discovery Hub (DDH) is an EarthCube Building Block project using technologies developed in CINERGI (Community Inventory of EarthCube Resources for Geoscience Interoperability) to enable geoscience users to explore a growing portfolio of EarthCube-created and other geoscience-related resources. Over 1 million metadata records are available for discovery through the project portal (cinergi.sdsc.edu). These records are retrieved from data facilities, including federal, state and academic sources, or contributed by geoscientists through workshops, surveys, or other channels. CINERGI metadata augmentation pipeline components 1) provide semantic enhancement based on a large ontology of geoscience terms, using text analytics to generate keywords with references to ontology classes, 2) add spatial extents based on place names found in the metadata record, and 3) add organization identifiers to the metadata. The records are indexed and can be searched via a web portal and standard search APIs. The added metadata content improves discoverability and interoperability of the registered resources. Specifically, the addition of ontology-anchored keywords enables faceted browsing and lets users navigate to datasets related by variables measured, equipment used, science domain, processes described, geospatial features studied, and other dataset characteristics that are generated by the pipeline. DDH also lets data curators access and edit the automatically generated metadata records using the CINERGI metadata editor, accept or reject the enhanced metadata content, and consider it in updating their metadata descriptions. We consider several complex data discovery workflows, in environmental seismology (quantifying sediment and water fluxes using seismic data), marine biology (determining available temperature, location, weather and bleaching characteristics of coral reefs related to measurements in a given coral reef survey), and river geochemistry (discovering

  10. Mosaic organization of the hippocampal neuroepithelium and the multiple germinal sources of dentate granule cells

    Altman, J.; Bayer, S.A.

    1990-01-01

    This study deals with the site of origin, migration, and settling of the principal cell constituents of the rat hippocampus during the embryonic period. The results indicate that the hippocampal neuroepithelium consists of three morphogenetically discrete components--the Ammonic neuroepithelium, the primary dentate neuroepithelium, and the fimbrial glioepithelium--and that these are discrete sources of the large neurons of Ammon's horn, the smaller granular neurons of the dentate gyrus, and the glial cells of the fimbria. The putative Ammonic neuroepithelium is marked in short-survival thymidine radiograms by a high level of proliferative activity and evidence of interkinetic nuclear migration from day E16 until day E19. On days E16 and E17 a diffuse band of unlabeled cells forms outside the Ammonic neuroepithelium. These postmitotic cells are considered to be stratum radiatum and stratum oriens neurons, which are produced in large numbers as early as day E15. A cell-dense layer, the incipient stratum pyramidale, begins to form on day E18 and spindle-shaped cells can be traced to it from the Ammonic neuroepithelium. This migratory band increases in size for several days, then declines, and finally disappears by day E22. It is inferred that this migration contains the pyramidal cells of Ammon's horn that are produced mostly on days E17 through E20. The putative primary dentate neuroepithelium is distinguished from the Ammonic neuroepithelium during the early phases of embryonic development by its location, shape, and cellular dynamics. It is located around a ventricular indentation, the dentate notch, contains fewer mitotic cells near the lumen of the ventricle than the Ammonic neuroepithelium, and shows a different labeling pattern both in short-survival and sequential-survival thymidine radiograms

  11. Sources

    Duffy, L.P.

    1991-01-01

    This paper discusses the sources of radiation in the narrow perspective of radioactivity and the even narrow perspective of those sources that concern environmental management and restoration activities at DOE facilities, as well as a few related sources. Sources of irritation, Sources of inflammatory jingoism, and Sources of information. First, the sources of irritation fall into three categories: No reliable scientific ombudsman to speak without bias and prejudice for the public good, Technical jargon with unclear definitions exists within the radioactive nomenclature, and Scientific community keeps a low-profile with regard to public information. The next area of personal concern are the sources of inflammation. This include such things as: Plutonium being described as the most dangerous substance known to man, The amount of plutonium required to make a bomb, Talk of transuranic waste containing plutonium and its health affects, TMI-2 and Chernobyl being described as Siamese twins, Inadequate information on low-level disposal sites and current regulatory requirements under 10 CFR 61, Enhanced engineered waste disposal not being presented to the public accurately. Numerous sources of disinformation regarding low level radiation high-level radiation, Elusive nature of the scientific community, The Federal and State Health Agencies resources to address comparative risk, and Regulatory agencies speaking out without the support of the scientific community

  12. Bakery products as a source of total dietary fiber in young adults.

    Markiewicz-Żukowska, Renata; Moskwa, Justyna; Gromkowska-Kępka, Krystyna; Laskowska, Emilia; Laskowska, Jolanta; Tomczuk, Justyna; Borawska, Maria Halina

    2016-01-01

    Bakery products are a source of bioactive compounds, such as dietary fibre (DF), whose proper supply plays an important role in prevention of civilisation diseases. The aim of the present study was to determine total dietary fibre (TDF) content in bakery products and their contribution to TDF supply. The determination of TDF content was performed using enzymatic-gravimetric method in 72 samples of six types of bakery products (wholemeal rye bread, wheat-rye bread, wheat-rye bread with grains, toast bread, crispbread, rolls) included in the young adults diet. Simultaneously, frequency of bakery products consumption and their contribution to TDF supply were assessed based on dietary interview questionnaires carried out among 224 students from Poland. Index of nutritional quality (INQ) of examined bakery products was calculated. Our data indicate that average TDF content depended on the type of bakery products and ranged from 2.19 g/100 g in rolls to 11.80 g/100 g in wholemeal rye bread. All of the tested types of bakery products, except rolls, were a good source of fibre (INQ≥1), but the richest were wholemeal rye and wheat-rye with grains breads. Analysis of questionnaires data showed that bakery products were regularly consumed by 80% of young adults; however, most of whom preferred rolls. Consumption of bakery products covered current recommendations for dietary fibre in 27%. Daily intake of bakery products and TDF was not correlated with student's BMI, however, women frequently consuming bread had a lower BMI than those who rarely ate it. Wholemeal rye and wheat-rye with grains breads are the rich source of TDF and they should be consumed by young adults in order to achieve the recommended TDF values.

  13. Trustworthiness of product review blogs:a source trustworthiness scale validation

    Ghazisaeedi, Mehdi; Steyn, Peter; van Heerden, Gene

    2012-01-01

    With the introduction of Web 2.0, online blogging has established its place in the lexicon of public relations management. Especially blogs that offer reviews of products, services and technologies, have become essential to practitioners of public relations in their dialogue with the market place. From a public relations perspective, this paper addresses the source trustworthiness of product review blogs among online consumers, and whether consumer demographics have a significant impact on th...

  14. Cr(Vi) reduction capacity of activated sludge as affected by nitrogen and carbon sources, microbial acclimation and cell multiplication

    Ferro Orozco, A.M.; Contreras, E.M.; Zaritzky, N.E.

    2010-01-01

    The objectives of the present work were: (i) to analyze the capacity of activated sludge to reduce hexavalent chromium using different carbon sources as electron donors in batch reactors, (ii) to determine the relationship between biomass growth and the amount of Cr(VI) reduced considering the effect of the nitrogen to carbon source ratio, and (iii) to determine the effect of the Cr(VI) acclimation stage on the performance of the biological chromium reduction assessing the stability of the Cr(VI) reduction capacity of the activated sludge. The highest specific Cr(VI) removal rate (q Cr ) was attained with cheese whey or lactose as electron donors decreasing in the following order: cheese whey ∼ lactose > glucose > citrate > acetate. Batch assays with different nitrogen to carbon source ratio demonstrated that biological Cr(VI) reduction is associated to the cell multiplication phase; as a result, maximum Cr(VI) removal rates occur when there is no substrate limitation. The biomass can be acclimated to the presence of Cr(VI) and generate new cells that maintain the ability to reduce chromate. Therefore, the activated sludge process could be applied to a continuous Cr(VI) removal process.

  15. NoSQL data model for semi-automatic integration of ethnomedicinal plant data from multiple sources.

    Ningthoujam, Sanjoy Singh; Choudhury, Manabendra Dutta; Potsangbam, Kumar Singh; Chetia, Pankaj; Nahar, Lutfun; Sarker, Satyajit D; Basar, Norazah; Das Talukdar, Anupam

    2014-01-01

    Sharing traditional knowledge with the scientific community could refine scientific approaches to phytochemical investigation and conservation of ethnomedicinal plants. As such, integration of traditional knowledge with scientific data using a single platform for sharing is greatly needed. However, ethnomedicinal data are available in heterogeneous formats, which depend on cultural aspects, survey methodology and focus of the study. Phytochemical and bioassay data are also available from many open sources in various standards and customised formats. To design a flexible data model that could integrate both primary and curated ethnomedicinal plant data from multiple sources. The current model is based on MongoDB, one of the Not only Structured Query Language (NoSQL) databases. Although it does not contain schema, modifications were made so that the model could incorporate both standard and customised ethnomedicinal plant data format from different sources. The model presented can integrate both primary and secondary data related to ethnomedicinal plants. Accommodation of disparate data was accomplished by a feature of this database that supported a different set of fields for each document. It also allowed storage of similar data having different properties. The model presented is scalable to a highly complex level with continuing maturation of the database, and is applicable for storing, retrieving and sharing ethnomedicinal plant data. It can also serve as a flexible alternative to a relational and normalised database. Copyright © 2014 John Wiley & Sons, Ltd.

  16. [Effects of carbon and nitrogen sources on 5-keto-gluconic acid production].

    Tan, Zhilei; Wang, Hongcui; Wei, Yuqiao; Li, Yanyan; Zhong, Cheng; Jia, Shiru

    2014-01-01

    Gluconobacter oxydans is known to oxidize glucose to gluconic acid (GA), and subsequently, to 2-keto-gluconic acid (2KGA) and 5-keto-gluconic acid (5KGA), while 5KGA can be converted to L-(+)-tartaric acid. In order to increase the production of 5KGA, Gluconobacter oxydans HGI-1 that converts GA to 5KGA exclusively was chosen in this study, and effects of carbon sources (lactose, maltose, sucrose, amylum and glucose) and nitrogen sources (yeast extract, fish meal, corn steep liquor, soybean meal and cotton-seed meal) on 5KGA production were investigated. Results of experiment in 500 mL shake-flask show that the highest yield of 5KGA (98.20 g/L) was obtained using 100 g/L glucose as carbon source. 5KGA reached 100.20 g/L, 109.10 g/L, 99.83 g/L with yeast extract, fish meal and corn steep liquor as nitrogen source respectively, among which the optimal nitrogen source was fish meal. The yield of 5KGA by corn steep liquor is slightly lower than that by yeast extract. For the economic reason, corn steep liquor was selected as nitrogen source and scaled up to 5 L stirred-tank fermentor, and the final concentration of 5KGA reached 93.80 g/L, with its maximum volumetric productivity of 3.48 g/(L x h) and average volumetric productivity of 1.56 g/(L x h). The result obtained in this study showed that carbon and nitrogen sourses for large-scale production of 5KGA by Gluconobacter oxydans HGI-1 were glucose and corn steep liquor, respectively, and the available glucose almost completely (85.93%) into 5KGA.

  17. Lecithin: a by-product of biodiesel production and a source of choline for dairy cows

    Igino Andrighetto

    2012-04-01

    Full Text Available The aim of the present study was to compare the effects of soy lecithins (L, a by-product of the biodiesel production process, and choline chloride microencapsulated with hydrogenated vegetable oils (C on dry matter intake, milk yield,  milk quality traits, milk choline and haematological profile of dairy cows. A total of 12 mid-lactating Holstein Friesian cows were assigned to one of two experimental groups and fed according to cross-over design (2 diets x 2 periods. Diets were isoenergetic, isofibrous and isonitrogenous and had the same content of choline. Dry matter intake was not affected by the diet, but L led to lower milk choline (P

  18. Numerical study of cesium effects on negative ion production in volume sources

    Fukumasa, Osamu; Niitani, Eiji [Yamaguchi Univ., Ube (Japan). Faculty of Engineering

    1997-02-01

    Effects of cesium vapor injection of H{sup -} production in a tandem negative ion source are studied numerically as a function of plasma parameters. Model calculation is done by solving a set of particle balance equations in a steady-state hydrogen discharge plasmas. Here, the results which focus on gas pressure and electron temperature dependences of H{sup -} volume production are presented and discussed. With including H{sup -} surface production processes caused by both H atoms and positive hydrogen ions, enhancement of H{sup -} production and pressure dependence of H{sup -} production observed experimentally are well reproduced in the model. To enhance H{sup -} production, however, so-called electron cooling is not so effective if plasma parameters are initially optimized with the use of magnetic filter. (author)

  19. Production of γ-aminobutyric acid by microorganisms from different food sources.

    Hudec, Jozef; Kobida, Ľubomír; Čanigová, Margita; Lacko-Bartošová, Magdaléna; Ložek, Otto; Chlebo, Peter; Mrázová, Jana; Ducsay, Ladislav; Bystrická, Judita

    2015-04-01

    γ-Aminobutyric acid (GABA) is a potentially bioactive component of foods and pharmaceuticals. The aim of this study was screen lactic acid bacteria belonging to the Czech Collection of Microorganisms, and microorganisms (yeast and bacteria) from 10 different food sources for GABA production by fermentation in broth or plant and animal products. Under an aerobic atmosphere, very low selectivity of GABA production (from 0.8% to 1.3%) was obtained using yeast and filamentous fungi, while higher selectivity (from 6.5% to 21.0%) was obtained with bacteria. The use of anaerobic conditions, combined with the addition of coenzyme (pyridoxal-5-phosphate) and salts (CaCl2 , NaCl), led to the detection of a low concentration of GABA precursor. Simultaneously, using an optimal temperature of 33 °C, a pH of 6.5 and bacteria from banana (Pseudomonadaceae and Enterobacteriaceae families), surprisingly, a high selectivity of GABA was obtained. A positive impact of fenugreek sprouts on the proteolytic process and GABA production from plant material as a source of GABA precursor was identified. Lactic acid bacteria for the production of new plant and animal GABA-rich products from different natural sources containing GABA precursor can be used. © 2014 Society of Chemical Industry.

  20. Metabolic engineering of Corynebacterium glutamicum aimed at alternative carbon sources and new products

    Volker Fritz Wendisch

    2012-10-01

    Full Text Available Corynebacterium glutamicum is well known as the amino acid-producing workhorse of fermentation industry, being used for multi-million-ton scale production of glutamate and lysine for more than 60 years. However, it is only recently that extensive research has focused on engineering it beyond the scope of amino acids. Meanwhile, a variety of corynebacterial strains allows access to alternative carbon sources and/or allows production of a wide range of industrially relevant compounds. Some of these efforts set new standards in terms of titers and productivities achieved whereas others represent a proof-of-principle. These achievements manifest the position of C. glutamicum as an important industrial microorganism with capabilities far beyond the traditional amino acid production. In this review we focus on the state of the art of metabolic engineering of C. glutamicum for utilization of alternative carbon sources, (e.g. coming from wastes and unprocessed sources, and construction of C. glutamicum strains for production of new products such as diamines, organic acids and alcohols.

  1. Estimating average alcohol consumption in the population using multiple sources: the case of Spain.

    Sordo, Luis; Barrio, Gregorio; Bravo, María J; Villalbí, Joan R; Espelt, Albert; Neira, Montserrat; Regidor, Enrique

    2016-01-01

    National estimates on per capita alcohol consumption are provided regularly by various sources and may have validity problems, so corrections are needed for monitoring and assessment purposes. Our objectives were to compare different alcohol availability estimates for Spain, to build the best estimate (actual consumption), characterize its time trend during 2001-2011, and quantify the extent to which other estimates (coverage) approximated actual consumption. Estimates were: alcohol availability from the Spanish Tax Agency (Tax Agency availability), World Health Organization (WHO availability) and other international agencies, self-reported purchases from the Spanish Food Consumption Panel, and self-reported consumption from population surveys. Analyses included calculating: between-agency discrepancy in availability, multisource availability (correcting Tax Agency availability by underestimation of wine and cider), actual consumption (adjusting multisource availability by unrecorded alcohol consumption/purchases and alcohol losses), and coverage of selected estimates. Sensitivity analyses were undertaken. Time trends were characterized by joinpoint regression. Between-agency discrepancy in alcohol availability remained high in 2011, mainly because of wine and spirits, although some decrease was observed during the study period. The actual consumption was 9.5 l of pure alcohol/person-year in 2011, decreasing 2.3 % annually, mainly due to wine and spirits. 2011 coverage of WHO availability, Tax Agency availability, self-reported purchases, and self-reported consumption was 99.5, 99.5, 66.3, and 28.0 %, respectively, generally with downward trends (last three estimates, especially self-reported consumption). The multisource availability overestimated actual consumption by 12.3 %, mainly due to tourism imbalance. Spanish estimates of per capita alcohol consumption show considerable weaknesses. Using uncorrected estimates, especially self-reported consumption, for

  2. Contrasts between estimates of baseflow help discern multiple sources of water contributing to rivers

    Cartwright, I.; Gilfedder, B.; Hofmann, H.

    2014-01-01

    This study compares baseflow estimates using chemical mass balance, local minimum methods, and recursive digital filters in the upper reaches of the Barwon River, southeast Australia. During the early stages of high-discharge events, the chemical mass balance overestimates groundwater inflows, probably due to flushing of saline water from wetlands and marshes, soils, or the unsaturated zone. Overall, however, estimates of baseflow from the local minimum and recursive digital filters are higher than those based on chemical mass balance using Cl calculated from continuous electrical conductivity measurements. Between 2001 and 2011, the baseflow contribution to the upper Barwon River calculated using chemical mass balance is between 12 and 25% of the annual discharge with a net baseflow contribution of 16% of total discharge. Recursive digital filters predict higher baseflow contributions of 19 to 52% of discharge annually with a net baseflow contribution between 2001 and 2011 of 35% of total discharge. These estimates are similar to those from the local minimum method (16 to 45% of annual discharge and 26% of total discharge). These differences most probably reflect how the different techniques characterise baseflow. The local minimum and recursive digital filters probably aggregate much of the water from delayed sources as baseflow. However, as many delayed transient water stores (such as bank return flow, floodplain storage, or interflow) are likely to be geochemically similar to surface runoff, chemical mass balance calculations aggregate them with the surface runoff component. The difference between the estimates is greatest following periods of high discharge in winter, implying that these transient stores of water feed the river for several weeks to months at that time. Cl vs. discharge variations during individual flow events also demonstrate that inflows of high-salinity older water occurs on the rising limbs of hydrographs followed by inflows of low

  3. USE OF MEAT-BONE PASTE AS A PROTEIN SOURCE IN MEAT PRODUCT PRODUCTION

    A. K. Kakimov

    2016-01-01

    Full Text Available In this paper, the results of the experimental research on developing the technology of a protein complex based on the meat-bone paste and protein-fat-blood emulsion are shown. The technological scheme of meat-bone paste production on the basis of complex grinding meat-bone raw material to bone particle size of 100 ∙10–6 m and further processing of bone particles using reagent, cheese whey, with pH 4,3 is presented. When studying the nutritive and biological value of the protein complex, it was established that the protein complex consisting of the food component from bone and protein-fat-blood emulsion could be used instead of the basic raw material in meat product production. The comparative analysis of the nutritive value of the protein complex and horse meat demonstrated the following results: the amino acid composition of the protein complex showed a balance of the essential amino acids and the high content of the essential amino acids which limit the biological value: lysine, leucine and threonine. The high content of polyunsaturated fatty acids was observed, which justified the biological value of the protein complex.

  4. Construction of a single/multiple wavelength RZ optical pulse source at 40 GHz by use of wavelength conversion in a high-nonlinearity DSF-NOLM

    Yu, Jianjun; Yujun, Qian; Jeppesen, Palle

    2001-01-01

    A single or multiple wavelength RZ optical pulse source at 40 GHz is successfully obtained by using wavelength conversion in a nonlinear optical loop mirror consisting of high nonlinearity-dispersion shifted fiber.......A single or multiple wavelength RZ optical pulse source at 40 GHz is successfully obtained by using wavelength conversion in a nonlinear optical loop mirror consisting of high nonlinearity-dispersion shifted fiber....

  5. Simulation of hadron multiple production by cosmic-ray protons in the incident energy region of 1015 eV

    Takatsuka, Ichiro

    1984-01-01

    The simulation studies of the unusual cosmic ray families found by the experiment at Mt. Chacaltaya were performed. Those families have a larger number of hadrons than the normal families, or are the families with big transverse extension. The former is called Centauro or Mini-centauro, and the latter is called Binocular and Chiron. In the first simulation, the process was calculated, in which the Lorentz transformation of π-meson multiple production (C-jet) in the energy region of 10 14 eV was made, and the jet with raised energy was combined, and the families were formed. The second simulation was made for the energy region more than 300 TeV, in which the nucleon-antinucleon multiple production with large transverse momentum and the B particle multiple production with larger transverse momentum were assumed. The data used were the C-jet data observed at Mt. Chacaltaya. For the simulation, all the primary particles were considered to be protons. The results of the present simulation study showed that the families with strong hadron components observed at Mt. Chacaltaya might be the new type hadron multiple production such as nucleon-antinucleon multiple production or B-particle multiple production. The total energy of all the families increased with the energy of the primary particles. There are a few families having the same extent of energy and spread as the Chiron. (Kato, T.)

  6. Phenology Data Products to Support Assessment and Forecasting of Phenology on Multiple Spatiotemporal Scales

    Gerst, K.; Enquist, C.; Rosemartin, A.; Denny, E. G.; Marsh, L.; Moore, D. J.; Weltzin, J. F.

    2014-12-01

    The USA National Phenology Network (USA-NPN; www.usanpn.org) serves science and society by promoting a broad understanding of plant and animal phenology and the relationships among phenological patterns and environmental change. The National Phenology Database maintained by USA-NPN now has over 3.7 million records for plants and animals for the period 1954-2014, with the majority of these observations collected since 2008 as part of a broad, national contributory science strategy. These data have been used in a number of science, conservation and resource management applications, including national assessments of historical and potential future trends in phenology, regional assessments of spatio-temporal variation in organismal activity, and local monitoring for invasive species detection. Customizable data downloads are freely available, and data are accompanied by FGDC-compliant metadata, data-use and data-attribution policies, vetted and documented methodologies and protocols, and version control. While users are free to develop custom algorithms for data cleaning, winnowing and summarization prior to analysis, the National Coordinating Office of USA-NPN is developing a suite of standard data products to facilitate use and application by a diverse set of data users. This presentation provides a progress report on data product development, including: (1) Quality controlled raw phenophase status data; (2) Derived phenometrics (e.g. onset, duration) at multiple scales; (3) Data visualization tools; (4) Tools to support assessment of species interactions and overlap; (5) Species responsiveness to environmental drivers; (6) Spatially gridded phenoclimatological products; and (7) Algorithms for modeling and forecasting future phenological responses. The prioritization of these data products is a direct response to stakeholder needs related to informing management and policy decisions. We anticipate that these products will contribute to broad understanding of plant

  7. Multiple regression technique for Pth degree polynominals with and without linear cross products

    Davis, J. W.

    1973-01-01

    A multiple regression technique was developed by which the nonlinear behavior of specified independent variables can be related to a given dependent variable. The polynomial expression can be of Pth degree and can incorporate N independent variables. Two cases are treated such that mathematical models can be studied both with and without linear cross products. The resulting surface fits can be used to summarize trends for a given phenomenon and provide a mathematical relationship for subsequent analysis. To implement this technique, separate computer programs were developed for the case without linear cross products and for the case incorporating such cross products which evaluate the various constants in the model regression equation. In addition, the significance of the estimated regression equation is considered and the standard deviation, the F statistic, the maximum absolute percent error, and the average of the absolute values of the percent of error evaluated. The computer programs and their manner of utilization are described. Sample problems are included to illustrate the use and capability of the technique which show the output formats and typical plots comparing computer results to each set of input data.

  8. Development of a surface ionization source for the production of radioactive alkali ion beams in SPIRAL

    Eleon, C.; Jardin, P.; Gaubert, G.; Saint-Laurent, M.-G.; Alcantara-Nunez, J.; Alves Conde, R.; Barue, C.; Boilley, D.; Cornell, J.; Delahaye, P.; Dubois, M.; Jacquot, B.; Leherissier, P.; Leroy, R.; Lhersonneau, G.; Marie-Jeanne, M.; Maunoury, L.; Pacquet, J.Y.; Pellemoine, F.; Pierret, C.

    2008-01-01

    In the framework of the production of radioactive alkali ion beams by the isotope separation on-line (ISOL) method in SPIRAL I, a surface ionization source has been developed at GANIL to produce singly-charged ions of Li, Na and K. This new source has been designed to work in the hostile environment whilst having a long lifetime. This new system of production has two ohmic heating components: the first for the target oven and the second for the ionizer. The latter, being in carbon, offers high reliability and competitive ionization efficiency. This surface ionization source has been tested on-line using a 48 Ca primary beam at 60.3 A MeV with an intensity of 0.14 pA. The ionization efficiencies obtained for Li, Na and K are significantly better than the theoretical values of the ionization probability per contact. The enhanced efficiency, due to the polarization of the ionizer, is shown to be very important also for short-lived isotopes. In the future, this source will be associated with the multicharged electron-cyclotron-resonance (ECR) ion source NANOGAN III for production of multicharged alkali ions in SPIRAL. The preliminary tests of the set up are also presented in this contribution.

  9. Effect of dietary starch source on milk production and composition of ...

    The objective of this study was to evaluate the effects of four sources of starch on milk production and composition, nutrient digestion and blood metabolites of lactating Holstein cows. Four multiparous Holstein cows (708 ± 70 kg of body weight; 83 ± 9 days in milk) were used in a 4 × 4 Latin square design with 21-d periods.

  10. Monochromatic light-emitting diode (LED source in layers hens during the second production cycle

    Rodrigo Borille

    2015-09-01

    Full Text Available ABSTRACTLight is an important environmental factor for birds, allowing not only their vision, but also influencing their physiological responses, such as behavioral and reproductive activity. The objective of this experiment was to evaluate the impact of different colors of monochromatic light (LED sources in laying hens production during the second laying cycle. The study was conducted in an experimental laying house during 70 days. A total of 300 laying hens Isa Brown® genetic strain, aged 95 weeks, in the second laying cycle were used in the study. The artificial light sources used were blue, yellow, green, red and white. The light regimen was continuous illumination of 17 h per day (12 h natural and 5 h artificial in a daily light regimen of 17L:5D (light: dark. The Latin Square design was adopted with five treatments (five colors divided into five periods, and five boxes, with six replicates of ten birds in each box. The production and egg quality were evaluated. The different colors of light source did not affect production parameters or egg quality (p > 0.05. The monochromatic light source may be considered as an alternative to artificial lighting in laying hens during the second production cycle.

  11. Fiber Based Mid Infrared Supercontinuum Source for Spectroscopic Analysis in Food Production

    Ramsay, Jacob; Dupont, Sune Vestergaard Lund; Keiding, Søren Rud

    Optimization of sustainable food production is a worldwide challenge that is undergoing continuous development as new technologies emerge. Applying solutions for food analysis with novel bright and broad mid-infrared (MIR) light sources has the potential to meet the increasing demands for food...

  12. Assessment of the risks associated with Iodine-125 handling production sources for brachytherapy

    Souza, Daiane C.B.; Rostelato, Maria Elisa C.; Vicente, Roberto; Zeituni, Carlos A.; Tiezzi, Rodrigo; Costa, Osvaldo L.; Souza, Carla D.; Peleias Junior, Fernando S.; Rodrigues, Bruna T.; Souza, Anderson S.; Batista, Talita Q.; Melo, Emerson R.; Camargo, Anderson R., E-mail: dcsouza@usp.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Karam Junior, Dib, E-mail: dib.karam@usp.br [Universidade de Sao Paulo (USP), Sao Paulo, SP (Brazil)

    2015-07-01

    In Brazil, prostate cancer is the second most frequent disease, with an estimated 68,800 new cases in 2013. This type of cancer can be treated with brachytherapy, which uses sealed sources of Iodine-125 implanted permanently in the prostate. These sources are currently imported at a high cost, making public treatment in large scale impractical. To reduce costs and to meet domestic demand, the laboratory for production of brachytherapy sources at the Nuclear and Energy Research Institute (IPEN) is currently nationalizing the production of this radioisotope. Iodine is quite volatile making the handling of its radioactive isotopes potentially dangerous. The aim of this paper is to evaluate the risks to which workers are exposed during the production and handling of the sources. The research method consisted initially of a literature review on the toxicity of iodine, intake limits, related physical risks, handling of accidents, generation of radioactive wastes, etc. The results allowed for establishing safety and radioprotection policies in order to ensure efficient and safe production in all stages and the implementation of good laboratory practices. (author)

  13. Assessment of the risks associated with Iodine-125 handling production sources for brachytherapy

    Souza, Daiane C.B.; Rostelato, Maria Elisa C.; Vicente, Roberto; Zeituni, Carlos A.; Tiezzi, Rodrigo; Costa, Osvaldo L.; Souza, Carla D.; Peleias Junior, Fernando S.; Rodrigues, Bruna T.; Souza, Anderson S.; Batista, Talita Q.; Melo, Emerson R.; Camargo, Anderson R.; Karam Junior, Dib

    2015-01-01

    In Brazil, prostate cancer is the second most frequent disease, with an estimated 68,800 new cases in 2013. This type of cancer can be treated with brachytherapy, which uses sealed sources of Iodine-125 implanted permanently in the prostate. These sources are currently imported at a high cost, making public treatment in large scale impractical. To reduce costs and to meet domestic demand, the laboratory for production of brachytherapy sources at the Nuclear and Energy Research Institute (IPEN) is currently nationalizing the production of this radioisotope. Iodine is quite volatile making the handling of its radioactive isotopes potentially dangerous. The aim of this paper is to evaluate the risks to which workers are exposed during the production and handling of the sources. The research method consisted initially of a literature review on the toxicity of iodine, intake limits, related physical risks, handling of accidents, generation of radioactive wastes, etc. The results allowed for establishing safety and radioprotection policies in order to ensure efficient and safe production in all stages and the implementation of good laboratory practices. (author)

  14. 40 CFR Table 2 to Subpart Xxxx of... - Emission Limits for Tire Cord Production Affected Sources

    2010-07-01

    ... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Emission Limits for Tire Cord Production Affected Sources 2 Table 2 to Subpart XXXX of Part 63 Protection of Environment ENVIRONMENTAL... Manufacturing Pt. 63, Subpt. XXXX, Table 2 Table 2 to Subpart XXXX of Part 63—Emission Limits for Tire Cord...

  15. The influence of carbon source and calcium on the production of ...

    use

    2011-12-10

    Dec 10, 2011 ... The influence of carbon source and calcium on the production of ... Furthermore, since the middle lamella contains high levels of calcium, it was thought that it may play an important ..... Processing of the pectate lyase PelI by ...

  16. Secrecy versus openness : Internet security and the limits of open source and peer production

    Schmidt, A.

    2014-01-01

    Open source and peer production have been praised as organisational models that could change the world for the better. It is commonly asserted that almost any societal activity could benefit from distributed, bottom-up collaboration — by making societal interaction more open, more social, and more

  17. Growth, productivity, and scientific impact of sources of HIV/AIDS ...

    This study uses an informetric approach to examine the growth, productivity and scientific impact of these sources, during the period 1980 to 2005, and especially to measure performance in the publication and dissemination of HIV/AIDS research about or from eastern or southern Africa. Data were collected from MEDLINE, ...

  18. Production of low axial energy spread ion beams with multicusp sources

    Lee, Yung -Hee Y. [Univ. of California, Berkeley, CA (United States)

    1998-05-01

    Multicusp ion sources are capable of producing ions with low axial energy spread which are necessary in applications such as: ion projection lithography (IPL) and focused ion beams for the next generation lithographic tools and nuclear science experiments such as radioactive ion beam production. The axial ion energy spread for multicusp source is approximately 6 eV which is too large for IPL and radioactive ion beam applications. The addition of a magnetic filter which consists of a pair of permanent magnets to the multicusp source reduces the energy spread considerably. The reduction is due to the improvement in the uniformity of the axial plasma potential distribution in the discharge region. Axial ion energy spread of the filament driven ion source has been measured using three different techniques. In all cases, it was found to be less than 2 eV. Energy spread of the radio frequency (RF) driven source has also been explored, and it was found to be less than 3 eV with the proper RF-shielding. A new multicusp source configuration has been designed and constructed to further reduce the energy spread. To achieve a more uniform axial plasma potential distribution, a cylindrical magnetic filter has been designed and constructed for a 2-cm-diameter source. This new source configuration, the co-axial source, is new in its kind. The energy spread in this source has been measured to be a record low of 0.6 eV. Because of the novelty of this device, some plasma parameters inside the source have been studied. Langmuir probe has been used to measure the plasma potential, the electron temperature and the density distribution.

  19. Production of low axial energy spread ion beams with multicusp sources

    Lee, Y.H.Y.

    1998-05-01

    Multicusp ion sources are capable of producing ions with low axial energy spread which are necessary in applications such as: ion projection lithography (IPL) and focused ion beams for the next generation lithographic tools and nuclear science experiments such as radioactive ion beam production. The axial ion energy spread for multicusp source is approximately 6 eV which is too large for IPL and radioactive ion beam applications. The addition of a magnetic filter which consists of a pair of permanent magnets to the multicusp source reduces the energy spread considerably. The reduction is due to the improvement in the uniformity of the axial plasma potential distribution in the discharge region. Axial ion energy spread of the filament driven ion source has been measured using three different techniques. In all cases, it was found to be less than 2 eV. Energy spread of the radio frequency (RF) driven source has also been explored, and it was found to be less than 3 eV with the proper RF-shielding. A new multicusp source configuration has been designed and constructed to further reduce the energy spread. To achieve a more uniform axial plasma potential distribution, a cylindrical magnetic filter has been designed and constructed for a 2-cm-diameter source. This new source configuration, the co-axial source, is new in its kind. The energy spread in this source has been measured to be a record low of 0.6 eV. Because of the novelty of this device, some plasma parameters inside the source have been studied. Langmuir probe has been used to measure the plasma potential, the electron temperature and the density distribution

  20. Source term analysis for a criticality accident in metal production line glove boxes

    Nguyen, D.H.

    1991-06-01

    A recent development in criticality accident analysis is the deterministic calculations of the transport of fission products and actinides through the barriers of the physical facility. The knowledge of the redistribution of the materials inside the facility will help determine the reentry and clean-up procedures. The amount of radioactive materials released to the environment is the source term for dispersion calculations. We have used an integrated computer model to determine the release of fission products to the environment from a hypothetical criticality event in a glove box of the metal production line (MPL) at the Lawrence Livermore National Laboratory (LLNL)