Development of multifilamentary NbTi and Nb3Sn composite conductors with very fine filaments

International Nuclear Information System (INIS)

Ogasawara, T.; Hubota, T.; Makiura, T.; Oda, Y.; Okon, H.; Yasohama, K.

1986-01-01

A NbTi multifilamentary composite conductor with about 10,000 filaments has been manufactured in long lengths. A filament diameter of 0.52 μm, a twist pitch of 1.13 mm, a strand diameter of 0.1 mm and a Cu/CuNi mixed matrix result in strongly reduced a.c. losses. The hysteresis loss and the coupling loss are 73 kW/m 3 and 56 kW/m 3 for a 50 Hz magnetic field with an amplitude of 1.5 T. From three strands a conductor was formed with a twist pitch of 2.4 mm. Several small coils were wound and operated at 50 Hz. One of the coils generated a maximum field of 1.52 T(center) at an operating current of the same size as the static critical current. Similarily the construction of a Nb 3 Sn multifilamentary composite conductor with about 280,000 sub-micron filaments for a.c. use was tried

New technology for fabrication of multifilament NbTi composite

International Nuclear Information System (INIS)

Yang, Y.K.; Ma, W.M.; Peng, W.N.

1988-01-01

Explosive bonding-rolling-drawing process has been developed to produce NbTi multifilamentary superconductors. Multifilamentary wires of 0.5mm in diameter and 2.5km in length with 199 filaments of 25μm in dia. have been produced using this process. The critical current density (Jc) is 1.94x10 5 A/cm 2 at 4.2K and 5T for short samples and 4.9x10 4 A/cm 2 and 4.2/K and 8.5T for the magnet have been reached

Irradiation and annealing effects of deuteron irradiated NbTi and V3Ga multifilamentary composite wires at low temperature

International Nuclear Information System (INIS)

Seibt, E.

1975-01-01

To study the effects of low-temperature irradiation on technological type II-superconductors, NbTi and V 3 Ga multifilamentary composite wires, the critical current I/sub c/ and transition temperature T/sub c/ were measured before and after irradiation with 50-MeV deuterons at 10 and 15 0 K, respectively. While the irradiation effects on I/sub c/ and T/sub c/ of NbTi are substantially unaffected, the V 3 Ga wires undergo a reduction in I/sub c/ of about 50 percent and T/sub c/ decreases from 14.7 +- 0.1 0 K to 12.3 +- 0.1 0 K at a total deuteron flux of 2.6 x 10 17 cm -2 . Annealing experiments at room temperature and 100 0 C show only a small recovery of the superconducting properties up to 15 percent. The field dependence of the volume pinning force densities P/sub V/ was determined and the results are shown to be consistent with a qualitative dynamic pinning model

Microstructural and mechanical characterization of biomedical Ti-Nb-Zr(-Ta) alloys

International Nuclear Information System (INIS)

Elias, L.M.; Schneider, S.G.; Schneider, S.; Silva, H.M.; Malvisi, F.

2006-01-01

In recent years there has been a significant development of novel implant alloys based on β-Ti such as Ti-Nb-Zr and Ti-Nb-Zr-Ta alloys systems. The purpose of this work is to provide characterization of Ti-35.3Nb-5.1Ta-7.1Zr and Ti-41.1Nb-7.1Zr alloys, in which Nb will substitute the atomic amount of Ta, with emphasis in the property-microstructure-composition relationships. These alloys are produced from commercially pure materials (Ti, Nb, Zr and Ta) by an arc melting method. All ingots were submitted to sequences of heat treatment (1000 deg. C/2 h - WQ), cold working by swaging procedures and other heat treatment (1000 deg. C/2 h - WQ). Specimens, in as cast and heat-treated condition, were examined by light and scanning electron microscopy (SEM). These results suggested the presence of β- and ω-phases. Mechanical properties were based on tensile and hardness tests. These alloys exhibit a lower modulus than that of conventional Ti alloys and the other mechanical properties are suitable for biomedical applications

Pulsed critical current measurements of NbTi in perpendicular and parallel pulsed magnetic fields using the new Cryo-BI-Pulse System

International Nuclear Information System (INIS)

Stehr, V; Tan, K S; Hopkins, S C; Glowacki, B A; Keyser, A De; Bockstal, L Van; Deschagt, J

2006-01-01

Rapid transport current versus high magnetic field characterisation of high-irreversibility type II superconductors is important to maximise their critical parameters. HTS conductors are already used to produce insert coils that increase the fields of conventional magnets made from NbTi (Nb, Ta) 3 Sn and Nb 3 Al wires. There is fundamental interest in the study of HTS tapes and wires in magnetic fields higher than 21T, the current limit of superconducting magnets producing a DC field. Such fields can be obtained by using pulse techniques. High critical currents cannot be routinely measured with a continuous current applied at liquid helium, hydrogen or neon temperatures because of thermal and mechanical effects. A newly developed pulsed magnetic field and pulsed current system which allows rapid J c (B, T) measurements of the whole range of superconducting materials was tested with a multifilamentary NbTi wire in perpendicular and parallel orientations

Method of treating Ti--Nb--Zr--Ta superconducting alloys

International Nuclear Information System (INIS)

Horiuchi, T.; Monju, Y.; Tatara, I.; Nagai, N.; Hisata, M.; Matsumoto, K.

1975-01-01

A superconducting alloy is formulated from 10 to 50 at. percent Ti, 20 to 50 at. percent Nb, 10 to 40 at. percent Zr, and 5 to 12 at. percent Ta. A Ti--Nb--Zr--Ta superconducting alloy with a fine, non-homogeneous structure is obtained by forming a β solid solution of Ti--Nb--Zr--Ta alloy by heating to a temperature within the β solid solution range, cooling, and then cold working the heated alloy. The cold worked alloy is heated to a temperature within the (β' + β'') alloy to maintain the peritectoid structure, cold worked, then heated to a temperature within the eutectoid range to form a multiphase alloy structure and then cooled and finally cold worked. (U.S.)

Magnetic hysteresis and complex susceptibility as measures of ac losses in a multifilamentary NbTi superconductor

International Nuclear Information System (INIS)

Goldfarb, R.B.; Clark, A.F.

1985-01-01

Magnetization and ac susceptibility of a standard NbTi superconductor were measured as a function of longitudinal dc magnetic field. The ac-field-amplitude and frequency dependences of the complex susceptibility are examined. The magnetization is related to the susceptibility by means of a theoretical derivation based on the field dependence of the critical current density. Hysteresis losses, obtained directly from dc hysteresis loops and derived theoretically from ac susceptibility and critical current density, were in reasonable agreement

Niobium alloys production with elements of high steam pressure and high ductilidate Nb46,5%Ti, Nb 1%Zr, Nb 1%Ti and Nb20% Ta

International Nuclear Information System (INIS)

Pinatti, D.G.; Baldan, C.A.; Dainesi, C.R.; Sandim, H.R.Z.

1988-01-01

The melting technology of niobium alloys with high ductilidade and high steam pressure, having the Ti, Zr and Ta as alloying elements is described. The electron beam technique for production of Nb 46,5%Ti, Nb 1%Zr and Nb 20%Ta alloys is analysed, aiming a product with high grade and low cost. (C.G.C.) [pt

Effect of stress on the critical current of NbTi multifilamentary composite wire

International Nuclear Information System (INIS)

Ekin, J.W.; Fickett, F.R.; Clark, A.F.

1977-01-01

Superconducting composites within large-scale magnets can be subjected to high stresses. These stresses arise from several sources, chief among them being the winding tension and prestressing during construction of the magnet, the thermomechanical forces incurred during thermal cycling to cryogenic temperatures, and especially in large-scale systems, the magnetomechanical forces generated when the magnet is energized. Typically, data on the critical-current characteristics of superconducting composites are obtained on wires that are in an unstressed state. Very little is known, however, about how the critical current behaves in wires experiencing stresses of the type described above. To measure these effects, short sample critical current tests were made under conditions simultaneously simulating the mechanical and magnetic environments of high-field superconducting magnets. The program was initiated both to form a basis for the fundamental understanding of stress effects on superconductor stability and to provide engineering data for optimizing design and construction of high-field magnets. The preliminary results indicate that NbTi multifilamentary superconducting composite wires are not characterized by a single critical current vs. field curve, but rather by a family of curves, each corresponding to a different operating stress level

Improved multifilamentary Nb3Sn conductors produced by the titanium-bronze process

International Nuclear Information System (INIS)

Tachikawa, K.; Itoh, K.; Kamata, K.; Moriai, H.; Tada, N.

1985-01-01

The effects of a titanium addition to the bronze matrix of superconducting Nb 3 Sn wires have been investigated. The titanium addition to the matrix remarkably increases the Nb 3 Sn growth rate and the high-field, critical current density of the wire. An overall critical-current density of 3.8 . 10 4 A/cm 2 at 15 T has been obtained for the multifilamentary Nb/Cu-7.5 at.% Sn-0.4 at.% Ti wire with 4.7 μm-diameter 31 x 331 cores. The anisotropy in the critical current with respect to the field direction becomes larger with increasing aspect ratio of the rectangular-shaped multifilamentary wires. A 9.5 mm wide and 1.8mm thick Nb/Cu-7.5Sn-0.4Ti conductor with 5 μm-diameter 349 x 361=125 989 cores has been successfully fabricated on an industrial scale. This conductor carries a superconducting current of over 1300 A at 16.5 T. The newly developed Ti-bronze Nb 3 Sn conductor makes it feasible to generate a field of proportional 15 T in a large diameter bore. (orig.)

Phase diagrams for pseudo-binary carbide systems TiC-NbC, TiC-TaC, ZrC-NbC, ZrC-TaC and HfC-TaC

International Nuclear Information System (INIS)

Gusev, A.I.

1985-01-01

Parameters of interaction and energy of mutual exchange in the liquid and solid phases of pseudobinary TiC-NbC, TiC-TaC, ZrC-NbC, ZrC-TaC, HfC-TaC systems are calculated with account of dependence on composition and temperature. Positions of liquidus-solidus phase boundaries on the phase diagrams of the mentioned systems are calculated on the basis of the determined mutual exchange energies in approximati.on of subregular solutions. The existance of latent decomposition ranges in the solid phase on the phase diagrams of the investgated systems is established

Mechanical Properties of TiTaHfNbZr High-Entropy Alloy Coatings Deposited on NiTi Shape Memory Alloy Substrates

Science.gov (United States)

Motallebzadeh, A.; Yagci, M. B.; Bedir, E.; Aksoy, C. B.; Canadinc, D.

2018-04-01

TiTaHfNbZr high-entropy alloy (HEA) thin films with thicknesses of about 750 and 1500 nm were deposited on NiTi substrates by RF magnetron sputtering using TiTaHfNbZr equimolar targets. The thorough experimental analysis on microstructure and mechanical properties of deposited films revealed that the TiTaHfNbZr films exhibited amorphous and cauliflower-like structure, where grain size and surface roughness increased concomitant with film thickness. More importantly, the current findings demonstrate that the TiTaHfNbZr HEA films with mechanical properties of the same order as those of the NiTi substrate constitute promising biomedical coatings effective in preventing Ni release.

Mechanical Properties of TiTaHfNbZr High-Entropy Alloy Coatings Deposited on NiTi Shape Memory Alloy Substrates

Science.gov (United States)

Motallebzadeh, A.; Yagci, M. B.; Bedir, E.; Aksoy, C. B.; Canadinc, D.

2018-06-01

TiTaHfNbZr high-entropy alloy (HEA) thin films with thicknesses of about 750 and 1500 nm were deposited on NiTi substrates by RF magnetron sputtering using TiTaHfNbZr equimolar targets. The thorough experimental analysis on microstructure and mechanical properties of deposited films revealed that the TiTaHfNbZr films exhibited amorphous and cauliflower-like structure, where grain size and surface roughness increased concomitant with film thickness. More importantly, the current findings demonstrate that the TiTaHfNbZr HEA films with mechanical properties of the same order as those of the NiTi substrate constitute promising biomedical coatings effective in preventing Ni release.

Design and fabrication of Sn-Nb-Cu-Ta-C composites for multifilamentary superconducting Nb/sub 3/Sn wires by using the modified tube technique

Energy Technology Data Exchange (ETDEWEB)

Glowacki, B A; Kosek, Z M

1987-10-01

The factors determining the design and fabrication of Nb/sub 3/Sn multifilamentary wires by the tube technique are discussed. New improved methods of obtaining multifilamentary Nb/sub 3/Sn wires on the basis of both external diffusion and internal diffusion processes, by using the tube technique in a simpler and less expensive way, are presented.

Low critical temperature superconductors for electromagnets

International Nuclear Information System (INIS)

Devred, A.

2002-01-01

After a brief history of the main discoveries in applied superconductivity (section 1), we discuss the structure and properties of NbTi and Nb3 Sn (section 2). Then, we explain why low critical-temperature superconductors are produced under the form of multifilamentary composites (section 3), and we review the manufacturing processes of NbTi and Nb3Sn wires (section 4). We follow by a description of the transition from the superconducting to the normal resistive state of multifilamentary composite wires (section 5) and we detail their magnetization properties section 6). Last, we present the most commonly used cable configurations (section 7) and we provide simple formulae illustrating on a few examples the computation of losses generated under time-varying magnetic fields (section 8). (author)

Evidence from EXAFS for Different Ta/Ti Site Occupancy in High Critical Current Density Nb3Sn Superconductor Wires.

Science.gov (United States)

Heald, Steve M; Tarantini, Chiara; Lee, Peter J; Brown, Michael D; Sung, ZuHawn; Ghosh, Arup K; Larbalestier, David C

2018-03-19

To meet critical current density, J c , targets for the Future Circular Collider (FCC), the planned replacement for the Large Hadron Collider (LHC), the high field performance of Nb 3 Sn must be improved, but champion J c values have remained static for the last 10 years. Making the A15 phase stoichiometric and enhancing the upper critical field H c2 by Ti or Ta dopants are the standard strategies for enhancing high field performance but detailed recent studies show that even the best modern wires have broad composition ranges. To assess whether further improvement might be possible, we employed Extended X-ray Absorption Fine Structure (EXAFS) to determine the lattice site location of dopants in modern high-performance Nb 3 Sn strands with J c values amongst the best so far achieved. Although Ti and Ta primarily occupy the Nb sites in the A15 structure, we also find significant Ta occupancy on the Sn site. These findings indicate that the best performing Ti-doped stand is strongly sub-stoichiometric in Sn and that antisite disorder likely explains its high average H c2 behavior. These new results suggest an important role for dopant and antisite disorder in minimizing superconducting property distributions and maximizing high field J c properties.

NbTaV-(Ti,W) refractory high-entropy alloys: Experiments and modeling

Energy Technology Data Exchange (ETDEWEB)

Yao, H.W. [Laboratory of Applied Physics and Mechanics of Advanced Materials, College of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan 030024 (China); Qiao, J.W., E-mail: qiaojunwei@gmail.com [Laboratory of Applied Physics and Mechanics of Advanced Materials, College of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan 030024 (China); Gao, M.C., E-mail: michael.gao@netl.doe.gov [National Energy Technology Laboratory, 1450 Queen Ave SW, Albany, OR 97321 (United States); AECOM, P.O. Box 1959, Albany, OR 97321 (United States); Hawk, J.A. [National Energy Technology Laboratory, 1450 Queen Ave SW, Albany, OR 97321 (United States); Ma, S.G. [Institute of Applied Mechanics and Biomedical Engineering, Taiyuan University of Technology, Taiyuan 030024 (China); Zhou, H.F. [Laboratory of Applied Physics and Mechanics of Advanced Materials, College of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan 030024 (China); Zhang, Y. [State Key Laboratory for Advanced Metals and Materials, University of Science and Technology Beijing, Beijing 100083 (China)

2016-09-30

This study reports the design and development of ductile and strong refractory single-phase high-entropy alloys (HEAs) for high temperature applications, based on NbTaV with addition of Ti and W. Assisted by CALPHAD modeling, a single body-centered cubic solid solution phase was experimentally confirmed in the as-cast ingots using X-ray diffraction and scanning electron microscopy. The observed elemental segregation in each alloy qualitatively agrees with CALPHAD prediction. The Vickers microhardnesses (and yield strengths) of the alloys are about 3 (and 3.5–4.4) times that those estimated from the rule of mixture. While NbTaTiVW shows an impressive yield strength of 1420 MPa with fracture strain of 20%, NbTaTiV exhibits exceptional compressive ductility at room temperature.

Performance of Nb3Sn multifilamentary superconductors in solenoidal magnets

International Nuclear Information System (INIS)

Sampson, W.B.; Suenaga, M.; Robins, K.E.

High current Nb 3 Sn multifilamentary conductors have been formed by heat treating cables braided from three types of composite wire. In the simplest configuration, these wires contain niobium filaments in a pure copper matrix. After braiding the conductor is coated with a layer of tin which diffuses through the copper during heat treatment to form Nb 3 S n filaments. The second configuration is made from wires containing niobium filaments in a copper-tin alloy and requires only heat treatment to form the Nb 3 Sn filaments. The third type of braid has wires which consist of groups of niobium filaments in the bronze matrix which are in turn in a copper matrix. Tantalum barriers surround each group of filaments to prevent the tin from contaminating the pure copper matrix. The cables have been wound into solenoids after heat treatment and the effect of mechanical handling was studied by monitoring the resistive voltage distribution in the coils. (U.S.)

Temperature Induced Degradation of Nb Ti/Cu Composite Superconductors

CERN Document Server

Scheuerlein, C; Senatore, C; Di Michiel, M; Thilly, L; Gerardin, A; Reluner, B; Oberli, L; Willering, G; Bottura, L

2009-01-01

The degradation mechanisms of state-of-the-art Nb-Ti/Cu superconductors are described, based on in-situ synchrotron X-ray diffraction measurements during heat treatment. A quantitative description of the Nb-Ti/Cu degradation in terms of critical current density, Cu stabiliser resistivity and mechanical composite strength is presented. In an applied magnetic field a significant critical current degradation is already observed after a 5-minute 400 °C heat treatment, due to variations of a-Ti precipitate size and distribution within the Nb-Ti alloy filaments. A strong degradation of the strand mechanical properties is observed after several minutes heating above 550 °C, which is also the temperature at which the formation of Cu Ti intermetallic phases is detected. Several minutes heating at 250 °C are sufficient to increase the RRR of the strongly cold work strands inside a Rutherford type cable from about 80 to about 240. Heating for several minutes at 400 °C does not cause a significant conductor degradati...

Effect of nitrogen addition and annealing temperature on superelastic properties of Ti-Nb-Zr-Ta alloys

Energy Technology Data Exchange (ETDEWEB)

Tahara, Masaki [Institute of Materials Science, University of Tsukuba, Tsukuba, Ibaraki 305-8573 (Japan); Kim, Hee Young, E-mail: heeykim@ims.tsukuba.ac.jp [Institute of Materials Science, University of Tsukuba, Tsukuba, Ibaraki 305-8573 (Japan); Hosoda, Hideki [Precision and Intelligence Laboratory, Tokyo Institute of Technology, Yokohama 226-8503 (Japan); Nam, Tae-hyun [School of Materials Science and Engineering. A, Structural Materials: Properties, Microstructure and Processingnd ERI, Gyeongsang National University, 900 Gazwadong, Jinju, Gyeongnam 660-701 (Korea, Republic of); Miyazaki, Shuichi, E-mail: miyazaki@ims.tsukuba.ac.jp [Institute of Materials Science, University of Tsukuba, Tsukuba, Ibaraki 305-8573 (Japan); School of Materials Science and Engineering. A, Structural Materials: Properties, Microstructure and Processingnd ERI, Gyeongsang National University, 900 Gazwadong, Jinju, Gyeongnam 660-701 (Korea, Republic of)

2010-10-15

Research highlights: In this study, the effects of composition and annealing temperature on microstructure, shape memory effect and superelastic properties were investigated in Ti-Nb-4Zr-2Ta-N alloys by measuring stress-strain curves at various temperatures and using transmission electron microscopy. Dissolution of {alpha} phase increases M{sub s} and decreases the critical stress for slip for the Ti-22Nb-4Zr-2Ta alloy while it causes the decrease of M{sub s} and the increase of the critical stress for slip for the Ti-20Nb-4Zr-2Ta-0.6N alloy. The different effect of dissolution of {alpha} phase can be attributed to the fact that N is absorbed in {alpha} phase. - Abstract: The composition dependence of the mechanical properties and martensitic transformation behavior of Ti-Nb-4Zr-2Ta-N alloys is investigated. The effect of annealing temperature on the microstructural evolution and superelastic properties in the N-added and N-free alloys is compared. The addition of N decreases M{sub s} of Ti-Nb-4Zr-2Ta alloys by about 200 K per 1 at.%N and improves the superelastic properties of Ti-Nb-4Zr-2Ta alloys. The dissolution of {alpha} phase increases the martensitic transformation start temperature and decreases the superelastic recovery strain for the N-free alloy, whereas it causes opposite effects for the N-added alloy. The different annealing temperature dependences of superelastic properties are discussed on the basis of microstructure observation.

Effect of nitrogen addition and annealing temperature on superelastic properties of Ti-Nb-Zr-Ta alloys

International Nuclear Information System (INIS)

Tahara, Masaki; Kim, Hee Young; Hosoda, Hideki; Nam, Tae-hyun; Miyazaki, Shuichi

2010-01-01

Research highlights: In this study, the effects of composition and annealing temperature on microstructure, shape memory effect and superelastic properties were investigated in Ti-Nb-4Zr-2Ta-N alloys by measuring stress-strain curves at various temperatures and using transmission electron microscopy. Dissolution of α phase increases M s and decreases the critical stress for slip for the Ti-22Nb-4Zr-2Ta alloy while it causes the decrease of M s and the increase of the critical stress for slip for the Ti-20Nb-4Zr-2Ta-0.6N alloy. The different effect of dissolution of α phase can be attributed to the fact that N is absorbed in α phase. - Abstract: The composition dependence of the mechanical properties and martensitic transformation behavior of Ti-Nb-4Zr-2Ta-N alloys is investigated. The effect of annealing temperature on the microstructural evolution and superelastic properties in the N-added and N-free alloys is compared. The addition of N decreases M s of Ti-Nb-4Zr-2Ta alloys by about 200 K per 1 at.%N and improves the superelastic properties of Ti-Nb-4Zr-2Ta alloys. The dissolution of α phase increases the martensitic transformation start temperature and decreases the superelastic recovery strain for the N-free alloy, whereas it causes opposite effects for the N-added alloy. The different annealing temperature dependences of superelastic properties are discussed on the basis of microstructure observation.

Multifilamentary Cu-Nb3Sn superconductor wires

International Nuclear Information System (INIS)

Rodrigues, D.; Pinatti, D.G.

1990-01-01

This paper reports on one of the main technological problems concerning Nb 3 Sn superconducting wires production which is the optimization of heat treatments for the formation of the A-15 intermetallic compound. At the present work, Nb 3 Sn superconducting wire is produced by solid-liquid diffusion method which increases considerably the critical current values of the superconductor. Through this method, niobium, copper and Sn 7% wt Cu alloy are kept in the pure state. Thus, the method dispenses intermediate heat treatments of recrystallization during the manufacturing process of the wire. After the wire was ready, optimization work of heat treatments was accomplished aiming to obtain its best superconducting characteristics, Measurement of critical temperature, critical current versus magnetic field, normal and at room temperature resistivity were performed, as well as scanning electron microscopy for determination of Nb 3 Sn layers and transmission electron microscopy measurements of redetermining the grain sizes in Nb 3 Sn formed in each treatment. It was obtained critical current densities of 1.8 x 10 6 A/cm 2 in the Nb 3 Sn layer, at 10 Teslas and 4.2 K. The samples were analyzed by employing the superconducting collective flux pinning theories and a satisfactory agreement between the experimental and theoretical data was attained. The production process and the small size of the filaments used made a successful optimization of the wire possible

Influence of cold deformation on martensite transformation and mechanical properties of Ti-Nb-Ta-Zr alloy

International Nuclear Information System (INIS)

Wang Liqiang; Lu Weijie; Qin Jining; Zhang Fan; Zhang Di

2009-01-01

Ti-35Nb-2Ta-3Zr alloy was fabricated by vacuum consumable arc melting furnace and hot pressing. Microstructure and phase transformation of solution-treated (ST) and cold-rolled (CR) plates of Ti-Nb-Ta-Zr alloy were observed. Different microstructure of strain-induced martensite transformation during cold deformation were investigated. With the increase of reduction of cold rolling, microstructure of α''-phase changed from acicular martensite to butterfly shaped martensite and showed variant crossed and cross-hatched when the reduction of cold rolling was over 60%. Mechanical properties and SEM images of the fracture surface indicated that the alloy fabricated by cold deformation showed favorable strength and plasticity. Owing to the excellent cold workability and biomedical safety of elements of Nb, Ta and Zr, Ti-Nb-Ta-Zr alloy contributed much to medical applications

Low critical temperature superconductors for electromagnets; Supraconducteurs a basse temperature critique pour electroaimants

Energy Technology Data Exchange (ETDEWEB)

Devred, A

2002-07-01

After a brief history of the main discoveries in applied superconductivity (section 1), we discuss the structure and properties of NbTi and Nb3 Sn (section 2). Then, we explain why low critical-temperature superconductors are produced under the form of multifilamentary composites (section 3), and we review the manufacturing processes of NbTi and Nb3Sn wires (section 4). We follow by a description of the transition from the superconducting to the normal resistive state of multifilamentary composite wires (section 5) and we detail their magnetization properties section 6). Last, we present the most commonly used cable configurations (section 7) and we provide simple formulae illustrating on a few examples the computation of losses generated under time-varying magnetic fields (section 8). (author)

Niobium Nb and tantalum Ta

International Nuclear Information System (INIS)

Busev, A.I.; Tiptsova, V.G.; Ivanov, V.M.

1978-01-01

The basic methods for determining niobium and tantalum in various objects are described. Nb and Ta are separated with the aid of N-benzoyl-N-phenylhydroxylamine by precipitating Nb(5) from a tartaric acid solution with subsequent precipitation of Ta from the filtrate. The gravimetric determination of Nb and Ta in steels is based on their quantitative separation from a diluted solution by way of hydrolysis with subsequent after-precipitation with phenylarsonic acid (in the absence of W). The gravimetric determination of Nb in the presence of W is carried out with the aid of Cupferron. To determine Nb in its carbide, Nb(5) reduced to Nb(3) is titrated with a solution of K 2 Cr 2 O 7 in the presence of phenyl-anthranilic acid. The photometric determination of Nb in tungsten-containing steels and in ores containing Ti, W, Mo and Cr is based on the rhodanide method. Nb is determined in alloys with Zr and Ti photometrically with the aid of 4-(2-pyridylazo)-resorcin and in alloyed steels with the aid of benzhydroxamic acid. The latter complex is extracted with chloroform. This method is used to determine Nb in rocks. The photometric determination of Ta in TiCl 4 is carried out with the aid of pyrogallol, in commercial niobium with the aid of methyl violet, and in steel with the aid of 4-(-pyridylazo)-resorcin. Also described is the polarographic determination of Nb in tantalum pentoxide

TiZrNbTaMo high-entropy alloy designed for orthopedic implants: As-cast microstructure and mechanical properties.

Science.gov (United States)

Wang, Shao-Ping; Xu, Jian

2017-04-01

Combining the high-entropy alloy (HEA) concept with property requirement for orthopedic implants, we designed a Ti 20 Zr 20 Nb 20 Ta 20 Mo 20 equiatomic HEA. The arc-melted microstructures, compressive properties and potentiodynamic polarization behavior in phosphate buffer solution (PBS) were studied in detail. It was revealed that the as-cast TiZrNbTaMo HEA consisted of dual phases with bcc structure, major bcc1 and minor bcc2 phases with the lattice parameters of 0.3310nm and 0.3379nm, respectively. As confirmed by nanoindentation tests, the bcc1 phase is somewhat harder and stiffer than the bcc2 phase. The TiZrNbTaMo HEA exhibited Young's modulus of 153GPa, Vickers microhardness of 4.9GPa, compressive yield strength of σ y =1390MPa and apparent plastic strain of ε p ≈6% prior to failure. Moreover, the TiZrNbTaMo HEA manifested excellent corrosion resistance in PBS, comparable to the Ti6Al4V alloy, and pitting resistance remarkably superior to the 316L SS and CoCrMo alloys. These preliminary advantages of the TiZrNbTaMo HEA over the current orthopedic implant metals in mechanical properties and corrosion resistance offer an opportunity to explore new orthopedic-implant alloys based on the TiZrNbTaMo concentrated composition. Copyright © 2016 Elsevier B.V. All rights reserved.

Characterization of NbTi multifilamentary superconducting wires

International Nuclear Information System (INIS)

Vellego, G.

1988-01-01

Pirelli is developing superconducting mulfilamentary NbTi wires, with current carrying capacities of up to 500 A, for use in magnetic resonance imaging (MRI) systems and in small research magnets. Pirelli and IFUSP have developed a system for assessing wire performance, whose quality is comparable to the equivalent systems at the Brookhaven National Laboratory (BNL) and at the National Bureau of Standards (NBS). In particular, a high sensitivity is required for critical current measurements, so that the modern criteria for definition of critical current can be used. These involve conductor resistivities of the order of 10 -12 ohm-cm. The methods of measurements of critical current in applied magnetic fields, of residual resistance ratio and of copper to superconductor ratio are described. The results of the first tests performed in Pirelli wires and in wires of other manufacturers are described. These include tests on a NBS standard reference material. These results are of the same quality as results obtained at BNL or NBS on the same wires. So this system can be very useful throughout the Pirelli program. (author) [pt

Evaluation of APC NbTi superconductor in a model dipole magnet

International Nuclear Information System (INIS)

Scanlan, R.M.; Lietzke, A.; Royet, J.; Wandesforde, A.; Taylor, C.E.; Wong, J.; Rudziak, M.K.

1993-01-01

The artificial pinning center (APC) approach to NbTi superconductor fabrication offers the potential benefits of higher current density and lower cost than the conventional process for NbTi. We have been evaluating several approaches for fabricating NbTi via the APC approach to determine whether these advantages can be realized in a practical conductor. The study began with the fabrication by several vendors of 10kg size samples which were evaluated as short samples. This was followed by the scale-up of one process to 150mm diameter billets. This material was evaluated first in a solenoid configuration and recently in a one-meter long dipole. We will report here on the results of these coil tests and other characterization results for this new material. We will also describe the plans to continue the scale-up to full size billets and we will discuss the potential cost savings of this approach compared with conventional NbTi fabrication

Strain dependence of the critical current and critical field in multifilamentary Nb3Sn composites

International Nuclear Information System (INIS)

Ekin, J.W.

1979-01-01

High-J/sub c/ multifilamentary Nb 3 Sn superconductors with widely varying amounts of prestrain and critical field values can be characterized fairly accurately by a single normalized critical field-strain relationship. Such a relationship permits first order prediction of critical-current degradation at arbitrary magnetic field magnitudes with knowledge of only two parameters for any conductor, the prestrain and the maximum critical field. Some of the conductor-fabrication factors affecting the parameters are considered

Mass production system and technology of NbTi superconductors

International Nuclear Information System (INIS)

Fukutsuka, Toshiro; Monju, Yoshiyuki; Tatara, Isamu; Noguchi, Masataka; Yokochi, Katsuhiro; Matsubara, Mitsuharu.

1984-01-01

A mass production system for NbTi superconductors is described, involving vacuum arc melting of the alloys, hot hydrostatic extrusion of the composite billets and special drawing and stranding techniques for the rods and wires. The qualities required for superconducting wires are assured by a variety of instrument measurement and inspection techniques drawn from accumulated cryogenic experiences. (author)

Influence of heating rates on in situ resistance measurements of a bronze route Nb-Sn-Cu-Ta multifilamentary conductor

International Nuclear Information System (INIS)

Tan, K.S.; Hopkins, S.C.; Glowacki, B.A.

2004-01-01

The superconducting properties of a bronze process multifilamentary conductor are controlled by the structure, dimensions and composition of the intermetallic layers, which are strongly influenced by the details of the heat treatments applied to the conductor. It has previously been reported that the electrical resistivity of a Vacuumschmelze bronze process conductor varies during heat treatment, and that analysis of the conductor as a set of parallel resistors allows the features of the resistivity variation to be assigned to the progress of Nb 3 Sn intermetallic phase formation. The behaviour of NSP2 Nb-Sn-Cu-Ta bronze process multifilamentary conductors (Imperial Metal Industries) is now reported as a function of the heating rate, in preparation for more complex non-isothermal heat treatment procedures. It is shown that the resistance of the wire measured in situ by an alternating current (AC) technique can be used to observe the progress of the formation of Nb 3 Sn, and that the comparison of resistometric measurements at different heating rates can give an indication of other processes (such as recovery and recrystallisation) occurring at lower temperatures during the heating up process prior to isothermal annealing. In addition, this wire containing only about 1% of copper was carefully chosen because of the broken tantalum barriers around individual copper filaments. Therefore, the resistometric measurements were used to attempt to detect the diffusion of tin from the bronze matrix into the copper filaments at lower temperatures without noticeable influence on Nb 3 Sn phase formation. Treating the NSP2 wire as a set of parallel resistors also permits estimates to be made of the intermetallic layer thicknesses from resistometric measurements, and these are shown to be in good agreement with estimates from scanning electron microscopy. The difference in critical temperature, T c , between wires heated at different rates, with the presence of the bronze matrix

Thermal cycling in multifilamentary superconducting composites

International Nuclear Information System (INIS)

Aragao, E.E.A. de.

1984-01-01

NbTi-Cu multifilamentary superconducting composites were embedded, polished, characterized by microscopic techniques, and analyzed in a qualitative and semiquantitative way by energy dispersion technique. The superconductors were submitted to thermal cycling between the ambient temperature and the boiling point of helium (4.2K), for different number of cycles. The aims were to study the correlation between the possible microstructural damages due to thermal stresses arising in the composite during cycling and the variation of properties of the material with the number of cycles as well as to verify the validity of an elastic model for thermal stresses for low temperature cycles. (author)

Progress of metallic superconductors in Japan

Energy Technology Data Exchange (ETDEWEB)

Tachikawa, Kyoji, E-mail: tacsuper@keyaki.cc.u-tokai.ac.jp [Faculty of Engineering, Tokai University, 4-1-1, Kitakaname, Hiratsuka, Kanagawa 259-1292 (Japan)

2013-01-15

Highlights: ► Japanese contributions on the R and D of different metallic superconductors are summarized. ► Nb–Ti wires have been developed for MRI, accelerator, MAGLEV train and other applications. ► Multifilamentary Nb{sub 3}Sn wires with excellent performance have been developed for high-field use. ► Long-length Nb{sub 3}Al wires with promising strain tolerance have been fabricated by a new process. -- Abstract: This article overviews the development of metallic superconductors in Japan covering different kinds of alloys and intermetallic compounds. Metallic superconductors have opened many new application areas in science and technology. Japan has been one of the leading countries in the world, both in the research and development and in large-scale manufacturing of metallic superconductors.

Critical current studies on fine filamentary NbTi accelerator wires

International Nuclear Information System (INIS)

Garber, M.; Sabatini, R.L.; Sampson, W.B.; Suenaga, M.

1986-01-01

The magnets for the Superconducting Super Collider, a high energy proton colliding beam accelerator, require a superconductor with very high current density (> 2400 A/mm 2 at 5 T) and very small filaments ( about 2μ m in diameter). Previous work has shown that by controling the formation of Cu 4 Ti compound particles on the filament surfaces it is possible to make fine filamentary NbTi wire with high critical current density. The performance of multi-filamentary wire is characterized by the current density and the quantity ''n'' which describes the superconducting-normal transition. Micrographs of wires having high J /SUB c/ and high n show smooth, uniform filaments. Recently wires of very high critical current and high n have been produced in experimental quantities by commercial manufacturers

Critical current studies on fine filamentary NbTi accelerator wires

International Nuclear Information System (INIS)

Garber, M.; Suenaga, M.; Sampson, W.B.; Sabatini, R.L.

1985-01-01

The magnets for the Superconductig Super Collider, a high energy proton colliding beam accelerator, require a superconductor with very high current density (>2400 A/mm 2 at 5 T) and very small filaments (approx. 2μm in diameter). Previous work has shown that by controlling the formation of Cu 4 Ti compound particles on the filament surfaces it is possible to make fine filamentary NbTi wire with high critical current density. The performance of multi-filamentary wire is characterized by the current density and the quantity ''n'' which describes the superconducting-normal transition. Micrographs of wires having high J/sub c/ and high n show smooth, uniform filaments. Recently wires of very high critical current and high n have been produced in experimental quantities by commercial manufactures

Nb and Ta layer doping effects on the interfacial energetics and electronic properties of LaAlO3/SrTiO3 heterostructure: first-principles analysis.

Science.gov (United States)

Nazir, Safdar; Behtash, Maziar; Cheng, Jianli; Luo, Jian; Yang, Kesong

2016-01-28

The two-dimensional electron gas (2DEG) formed at the n-type (LaO)(+1)/(TiO2)(0) interface in the polar/nonpolar LaAlO3/SrTiO3 (LAO/STO) heterostructure (HS) has emerged as a prominent research area because of its great potential for nanoelectronic applications. Due to its practical implementation in devices, desired physical properties such as high charge carrier density and mobility are vital. In this respect, 4d and 5d transition metal doping near the interfacial region is expected to tailor electronic properties of the LAO/STO HS system effectively. Herein, we studied Nb and Ta-doping effects on the energetics, electronic structure, interfacial charge carrier density, magnetic moment, and the charge confinements of the 2DEG at the n-type (LaO)(+1)/(TiO2)(0) interface of LAO/STO HS using first-principles density functional theory calculations. We found that the substitutional doping of Nb(Ta) at Ti [Nb(Ta)@Ti] and Al [Nb(Ta)@Al] sites is energetically more favorable than that at La [Nb(Ta)@La] and Sr [Nb(Ta)@Sr] sites, and under appropriate thermodynamic conditions, the changes in the interfacial energy of HS systems upon Nb(Ta)@Ti and Nb(Ta)@Al doping are negative, implying that the formation of these structures is energetically favored. Our calculations also showed that Nb(Ta)@Ti and Nb(Ta)@Al doping significantly improve the interfacial charge carrier density with respect to that of the undoped system, which is because the Nb(Ta) dopant introduces excess free electrons into the system, and these free electrons reside mainly on the Nb(Ta) ions and interfacial Ti ions. Hence, along with the Ti 3d orbitals, the Nb 4d and Ta 5d orbitals also contribute to the interfacial metallic states; accordingly, the magnetic moments on the interfacial Ti ions increase significantly. As expected, the Nb@Al and Ta@Al doped LAO/STO HS systems show higher interfacial charge carrier density than the undoped and other doped systems. In contrast, Nb@Ti and Ta@Ti doped systems may

Mechanical properties and microstructure of Ti-35.5Nb-5.7Ta beta alloy.

Science.gov (United States)

Bartakova, S; Prachar, P; Dvorak, I; Hruby, V; Vanek, J; Pospichal, M; Svoboda, E; Martikan, A; Konecna, H; Sedlak, I

2015-01-01

Titanium and titanium alloys represent generally accepted metallic biomaterials for clinical dentistry and dental implantology. In this paper, we present a Ti-35.5Nb-5.7Ta alloy with a special respect to its microstructure and mechanical characteristics, such as Young modulus of elasticity. Three thermal treatments differing in temperature and time of annealing were used during the Ti-35.5Nb-5.7Ta processing in order to evaluate the effects of ageing, melting annealing, and annealing on mechanical characteristics and microstructure. Using microscopy, the alloy was analyzed and the differences in shares of beta phase grains, alpha particles and precipitates evaluated. The three thermal treatments were evaluated also from technological point of view. The following thermal treatment was found optimal for the Ti-35.5Nb-5.7Ta alloy: melting annealing at 800 °C for 0.5 hour followed by a cold swaging with a 52-79 % deformation, and final hardening at 500 °C for 2 hours in water(Tab. 2, Fig. 3, Ref. 24).

Severe plastic deformation of α+β Ti-5Ta-1.8Nb alloy by cryo-rolling

International Nuclear Information System (INIS)

Dasgupta, Arup; Parida, Pradyumna Kumar; Saroja, S.; Vijayalakshmi, M.

2010-01-01

The α-β (β ∼ 8%) Ti5Ta1.8Nb alloy is under development at IGCAR for reprocessing applications owing to its superior corrosion resistance and weldability. A possible method to strengthen the alloy is to engineer the grain size to finer dimensions through severe plastic deformation (SPD). A detailed analysis of the study of evolution of microstructure and micro-texture in the SPD Ti-Ta-Nb alloy is presented

Wear resistance of laser-deposited boride reinforced Ti-Nb-Zr-Ta alloy composites for orthopedic implants

International Nuclear Information System (INIS)

Samuel, Sonia; Nag, Soumya; Scharf, Thomas W.; Banerjee, Rajarshi

2008-01-01

The inherently poor wear resistance of titanium alloys limits their application as femoral heads in femoral (hip) implants. Reinforcing the soft matrix of titanium alloys (including new generation β-Ti alloys) with hard ceramic precipitates such as borides offers the possibility of substantially enhancing the wear resistance of these composites. The present study discusses the microstructure and wear resistance of laser-deposited boride reinforced composites based on Ti-Nb-Zr-Ta alloys. These composites have been deposited using the LENS TM process from a blend of elemental Ti, Nb, Zr, Ta, and boron powders and consist of complex borides dispersed in a matrix of β-Ti. The wear resistance of these composites has been compared with that of Ti-6Al-4V ELI, the current material of choice for orthopedic femoral implants, against two types of counterfaces, hard Si 3 N 4 and softer SS440C stainless steel. Results suggest a substantial improvement in the wear resistance of the boride reinforced Ti-Nb-Zr-Ta alloys as compared with Ti-6Al-4V ELI against the softer counterface of SS440. The presence of an oxide layer on the surface of these alloys and composites also appears to have a substantial effect in terms of enhanced wear resistance

Manufacturing and quality assurance for the MFTF superconductor core

International Nuclear Information System (INIS)

Scanlan, R.M.; Johnston, J.E.; Waide, P.A.; Zeitlin, B.A.; Smith, G.B.; Nelson, C.T.

1979-01-01

A total of 55,000 m of multifilamentary Nb-Ti superconductor in minimum lengths of 380 m are required for the Mirror Fusion Test Facility. This conductor is a large cross-section monolith and, as such, has presented several new manufacturing challenges. In addition, a monolith requires more stringent quality assurance procedures than braids or cables. This paper describes the manufacturing steps and the quality assurance program which have been developed for the MFTF superconductor core

Chemical state and phase structure of (TaNbTiW)N films prepared by combined magnetron sputtering and PBII

Energy Technology Data Exchange (ETDEWEB)

Feng, Xingguo [State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001 (China); Tang, Guangze [National Key Laboratory of Materials Behavior and Evaluation in Space Environment, Harbin Institute of Technology, Harbin 150001 (China); Sun, Mingren [National Key Laboratory of Science and Technology on Precision Hot Processing of Metals Harbin Institute of Technology, Harbin Institute of Technology, Harbin 150001 (China); Ma, Xinxin, E-mail: maxin@hit.edu.cn [State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001 (China); Wang, Liqin [School of Mechatronics Engineering, Harbin Institute of Technology, Harbin, 150001 (China)

2013-09-01

(TaNbTiW)N films with thickness of ∼1000 nm are prepared on titanium alloy substrate by combined magnetron sputtering deposition and nitrogen plasma based ion implantation (N-PBII). Chemical state of the elements and phase structure of the films are investigated using X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD), respectively. The bonds of Ta-N, Nb-N, Ti-N-O and Ta-O are detected in the (TaNbTiW)N films, however both W-N and W-O are not found. The initial alloy film has a BCC structure, while the films with N-PBII treatment are composed of BCC and FCC structures. The hardness and elastic modulus of the films can be improved by increasing nitrogen implantation dose and reach maximum values of 9.0 GPa and 154.1 GPa, respectively.

Energy dissipation of composite multifilamentary superconductors for high-current ramp-field magnet applications

International Nuclear Information System (INIS)

Gung, C.Y.

1993-01-01

Energy dissipation, which is also called AC loss, of a composite multifilamentary superconducting wire is one of the most fundamental concerns in building a stable superconducting magnet. Characterization and reduction of AC losses are especially important in designing a superconducting magnet for generating transient magnetic fields. The goal of this thesis is to improve the understanding of AC-loss properties of superconducting wires developed for high-current ramp-field magnet applications. The major tasks include: (1) building an advanced AC-loss measurement system, (2) measuring AC losses of superconducting wires under simulated pulse magnet operations, (3) developing an analytical model for explaining the new AC-loss properties found in the experiment, and (4) developing a computational methodology for comparing AC losses of a superconducting wire with those of a cable for a superconducting pulse magnet. A new experimental system using an isothermal calorimetric method was designed and constructed to measure the absolute AC losses in a composite superconductor. This unique experimental setup is capable of measuring AC losses of a brittle Nb 3 Sn wire carrying high AC current in-phase with a large-amplitude pulse magnetic field. Improvements of the accuracy and the efficiency of this method are discussed. Three different types of composite wire have been measured: a Nb 3 Sn modified jelly-roll (MJR) internal-tin wire used in a prototype ohmic heating coil, a Nb 3 Sn internal-tin wire developed for a fusion reactor ohmic heating coil, and a NbTi wire developed for the magnets in a particle accelerator. The cross sectional constructions of these wires represent typical commercial wires manufactured for pulse magnet applications

Texture Evolution in a Ti-Ta-Nb Alloy Processed by Severe Plastic Deformation

Science.gov (United States)

Cojocaru, Vasile-Danut; Raducanu, Doina; Gloriant, Thierry; Cinca, Ion

2012-05-01

Titanium alloys are extensively used in a variety of applications because of their good mechanical properties, high biocompatibility, and corrosion resistance. Recently, β-type Ti alloys containing Ta and Nb have received much attention because they feature not only high specific strength but also biocorrosion resistance, no allergic problems, and biocompatibility. A Ti-25Ta-25Nb β-type titanium alloy was subjected to severe plastic deformation (SPD) processing by accumulative roll bonding and investigated with the aim to observe the texture developed during SPD processing. Texture data expressed by pole figures, inverse pole figures, and orientation distribution functions for the (110), (200), and (211) β-Ti peaks were obtained by XRD investigations. The results showed that it is possible to obtain high-intensity share texture modes ({001}) and well-developed α and γ-fibers; the most important fiber is the α-fiber ({001} to {114} to {112} ). High-intensity texture along certain crystallographic directions represents a way to obtain materials with high anisotropic properties.

Search for high entropy alloys in the X-NbTaTiZr systems (X = Al, Cr, V, Sn)

Energy Technology Data Exchange (ETDEWEB)

Poletti, Marco Gabriele, E-mail: marcogabriele.poletti@unito.it [Dipartimento di Chimica, Università di Torino, Via P. Giuria 7, 10125 Torino (Italy); Fiore, Gianluca [Dipartimento di Chimica, Università di Torino, Via P. Giuria 7, 10125 Torino (Italy); Szost, Blanka A. [Strategic and Emerging Technologies Team (TEC-TS), European Space Agency, ESTEC, 1 Keplerlaan, 2201 AZ Noordwijk (Netherlands); Battezzati, Livio [Dipartimento di Chimica, Università di Torino, Via P. Giuria 7, 10125 Torino (Italy)

2015-01-25

Highlights: • Composition of refractory high entropy alloys predicted. • Solid solutions found in VNbTaTiZr and AlNbTaTiZr. • Alloys containing Cr and Sn are multi-phased. - Abstract: High entropy alloys, i.e. solid solution phases, are sought in the X-NbTaTiZr equiatomic system where the X element was chosen as Al, Cr, V and Sn by applying recent criteria based on size and electronegativity mismatch of alloy components, number of itinerant and total valence electrons, and the temperature at which the free energy of mixing changes at the alloy composition. The alloys containing V and Al are mostly constituted by solid solutions in good agreement with prediction.

Microstructure, mechanical behavior and biocompatibility of powder metallurgy Nb-Ti-Ta alloys as biomedical material.

Science.gov (United States)

Liu, Jue; Chang, Lin; Liu, Hairong; Li, Yongsheng; Yang, Hailin; Ruan, Jianming

2017-02-01

Microstructures, mechanical properties, apatite-forming ability and in vitro experiments were studied for Nb-25Ti-xTa (x=10, 15, 20, 25, 35at.%) alloys fabricated by powder metallurgy. It is confirmed that the alloys could achieve a relative density over 80%. Meanwhile, the increase in Ta content enhances the tensile strength, elastic modulus and hardness of the as-sintered alloys. When increasing the sintering temperatures, the microstructure became more homogeneous for β phase, resulting in a decrease in the modulus and strength. Moreover, the alloys showed a good biocompatibility due to the absence of cytotoxic elements, and were suitable for apatite formation and cell adhesion. In conclusion, Nb-25Ti-xTa alloys are potentially useful in biomedical applications with their mechanical and biological properties being evaluated in this work. Copyright © 2016 Elsevier B.V. All rights reserved.

Making superconductors

International Nuclear Information System (INIS)

McDonald, W.K.

1981-01-01

A method is described of producing composite rod or wire of increased strength and fineness wherein the composite is formed by reducing a lamina of two metals which have been rolled to form a cylindrical billet in which one of the metals is in expanded form. The composite produced can be encased in copper and fabricated to produce a superconductor. Alloys contemplated for producing superconductors are Nb 3 Sn, Nb 3 Ga, Nb 3 Ge, Nb 3 Si, Nb-Ti, V 3 Ga, V 3 Si, V 3 Sn, V 3 Al, and V 3 Ge laminated on bronze, Al, Cu, Ta, or combinations thereof. (author)

Method of production multifilamentary intermetallic superconductors

International Nuclear Information System (INIS)

Marancik, W.G.; Young, M.S.

1980-01-01

A method of making A-15 type intermetallic superconductors is disclosed which features elimination of numerous annealing steps. Nb or V filaments are embedded in Cu matrices; annular layers of Sn or Ga, respectively, separated from each other by Cu layers, provide the other component of the intermetallic superconductors Nb3Sn and V3Ga

Cold-pressure-welded joints in large multifilamentary Nb--Ti superconductors

International Nuclear Information System (INIS)

Cornish, D.N.; Deis, D.W.; Zbasnik, J.P.

1977-01-01

A number of mechanical and electrical measurements were made on joints in typical conductors for the proposed mirror fusion test facility (MFTF) and high field test facility (HFTF). For such measurements, a commercially available cold-pressure-welding machine was used. For joints in the MFTF conductor, which has a large proportion of superconductor, joint strength approached conductor strength. For the HFTF conductor, where the Cu-to-superconductor ratio is 4.33/1, the joint is stronger than the conductor. Electrically, the joints were not superconducting.. While the resistance is higher than might be achieved by other forms of joining, we feel that the cold-weld joint has the advantages of simplicity, speed, reliability, and reproducibility. This makes the method attractive for MFTF, where resistance losses will be small compared with the total 4 K refrigeration requirements

Role of α precipitates in flux pinning in a superconducting Ti-Nb-Ta-Zr quaternary alloy

International Nuclear Information System (INIS)

Osamura, K.; Tsunekawa, H.; Monju, Y.; Horiuchi, T.

1984-01-01

The precipitation behaviour of the α phase in a Ti-27 at.% Nb-6 at% Ta-6 at% Zr alloy has been investigated mainly by means of small-angle X-ray scattering measurements, by which the average size and number density of α precipitates were determined. The alloy was isothermally aged at 643 K after cold-rolling to various thicknesses. During ageing the average size of α precipitates increased but the number density decreased. The effect of cold-rolling was to increase the volume fraction of α precipitates. The superconducting critical current density was measured for the same specimens after the metallographical investigation. The specific pinning force produced by α precipitates, which corresponds to the global pinning force density divided by the number density of precipitates, was found to be proportional to the cube of the particle radius. It was found that the global pinning force density can be described using a scaling rule in terms of the volume fraction of α precipitates and the reduced magnetic field. The dominant global pinning force in the present foil specimens, as well as in commercial multifilamentary wires, is attributed to α precipitates. Dislocations and their secondary substructure introduced by cold-working also contributed to flux pinning, and could offer nucleation sites for the α phase. (author)

Bone bonding bioactivity of Ti metal and Ti-Zr-Nb-Ta alloys with Ca ions incorporated on their surfaces by simple chemical and heat treatments.

Science.gov (United States)

Fukuda, A; Takemoto, M; Saito, T; Fujibayashi, S; Neo, M; Yamaguchi, S; Kizuki, T; Matsushita, T; Niinomi, M; Kokubo, T; Nakamura, T

2011-03-01

Ti15Zr4Nb4Ta and Ti29Nb13Ta4.6Zr, which do not contain the potentially cytotoxic elements V and Al, represent a new generation of alloys with improved corrosion resistance, mechanical properties, and cytocompatibility. Recently it has become possible for the apatite forming ability of these alloys to be ascertained by treatment with alkali, CaCl2, heat, and water (ACaHW). In order to confirm the actual in vivo bioactivity of commercially pure titanium (cp-Ti) and these alloys after subjecting them to ACaHW treatment at different temperatures, the bone bonding strength of implants made from these materials was evaluated. The failure load between implant and bone was measured for treated and untreated plates at 4, 8, 16, and 26 weeks after implantation in rabbit tibia. The untreated implants showed almost no bonding, whereas all treated implants showed successful bonding by 4 weeks, and the failure load subsequently increased with time. This suggests that a simple and economical ACaHW treatment could successfully be used to impart bone bonding bioactivity to Ti metal and Ti-Zr-Nb-Ta alloys in vivo. In particular, implants heat treated at 700 °C exhibited significantly greater bone bonding strength, as well as augmented in vitro apatite formation, in comparison with those treated at 600 °C. Thus, with this improved bioactive treatment process these advantageous Ti-Zr-Nb-Ta alloys can serve as useful candidates for orthopedic devices. Copyright © 2010 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

A Comparative Study on Corrosion Behavior of Ti-35Nb-5Ta-7Zr Ti-6Al-4V and CP-Ti in 0.9 wt% NaCl

Energy Technology Data Exchange (ETDEWEB)

Saji, Viswanathan S.; Jeong, Yong Hoon; Choe, Han Cheol [Andong National University, Andong (Korea, Republic of)

2009-08-15

Recently, quaternary titanium alloys of the system Ti-Nb-Ta-Zr received considerable research considerable research interest as potential implant materials because of their excellent mechanical properties and biocompatibility. However, only few reported works were available on the corrosion behavior of such alloys. Hence, in the present work, electrochemical corrosion of Ti-35Nb-5Ta-7Zr alloy, which has been fabricated by are melting and heat treatment, was studied in 0.9 wt% NaCl at 37{+-}1 .deg. C, along with biomedical grade Ti-6Al-4V and CP-Ti. The phase and microstructure of the alloys were investigated employing XRD and SEM. The results of electrochemical studies indicated that the corrosion resistance of the quaternary alloy was inferior to that of Ti-6Al-4V and CP Ti.

New Al5 multifilamentary superconductor based on the niobium--aluminum--silicon system

International Nuclear Information System (INIS)

Quinn, G.C.

1977-12-01

Based on Powder Metallurgy techniques, a process to fabricate Nb-Nb 3 (Al,Si) multifilamentary superconducting wire has been developed. Optimum sintering and infiltration parameters are listed and the methods of mechanical reduction to wire form are described. Preliminary data indicate that diffusion reaction temperatures as low as 850 0 C form the A15 superconducting compound Nb 3

Anion exchange behavior of Ti, Zr, Hf, Nb and Ta as homologues of Rf and Db in mixed HF-acetone solutions

International Nuclear Information System (INIS)

Aksenov, N.V.; Bozhikov, G.A.; Starodub, G.Ya.; Dmitriev, S.N.; Filosofov, D.V.; Jon Sun Jin; Radchenko, V.I.; Lebedev, N.A.; Novgorodov, A.F.

2009-01-01

We studied in detail the sorption behavior of Ti, Zr, Hf, Nb and Ta on AG 1 anion exchange resin in HF-acetone mixed solutions as a function of organic cosolvent and acid concentrations. Anion exchange behavior was found to be strongly acetone concentration dependent. The distribution coefficients of Ti, Zr, Hf and Nb increased and those of Ta decreased with increasing content of acetone in HF solutions. With increasing HF concentration, anion exchange equilibrium analysis indicated the formation of fluoride complexes of group-4 elements with charge -3 and Ta with charge -2. For Nb the slope of -2 increased up to -5. Optimal conditions for separation of the elements using AIX chromatography were found. Group-4 elements formed MF 7 3- (M = Ti, Zr, Hf) complexes whose sorption decreased Ti > Hf > Zr in reverse order of complex stability. This fact is of particular interest for studying ion exchange behavior of Rf compared to Ti. The advantages of studying chemical properties of Rf and Db in aqueous HF solutions mixed with organic solvents are briefly discussed

Development of high performance Nb-Ti(Fe) multifilamentary superconductor for the LHC insertion quadrupoles

CERN Document Server

Lee, P J; Gabr-Rayan, W; Larbalestier, D C; Naus, M T; Squitieri, A A; Starch, W L; Barzi, E; Limon, P J; Sabbi, G L; Zlobin, A V; Kanithi, H; Hong, S; McKinnell, J C; Neff, D

1999-01-01

A development program was initiated in order to develop strand with improved current density at 10.5 T and 1.9 K over existing SSCL designs. The two successful strand designs reported on here both utilized high Fe content Nb-47 wtTi $9 alloys to improve the critical current density at high field by 7 At 10.5 T and 1.9 K, critical current densities exceeding 1450 A/mm/sup 2/ were obtained. In this paper we report detailed quantification of the macro- and micro- $9 structures of these strands and correlate these with critical current density measurements at 1.9 K and 4.2 K. The high Fe content significantly reduced the alpha -Ti precipitate size. The linear relationship between critical current $9 density and precipitate volume found is in agreement with earlier studies. High resolution FESEM electron backscatter contrast suggests a thin layer of high atomic number at grain boundaries. (12 refs).

Effects of shot-peening and atmospheric-pressure plasma on aesthetic improvement of Ti-Nb-Ta-Zr alloy for dental applications

Science.gov (United States)

Miura-Fujiwara, Eri; Suzuki, Yuu; Ito, Michiko; Yamada, Motoko; Matsutake, Sinpei; Takashima, Seigo; Sato, Hisashi; Watanabe, Yoshimi

2018-01-01

Ti and Ti alloys are widely used for biomedical applications such as artificial joints and dental devices because of their good mechanical properties and biochemical compatibility. However, dental devices made of Ti and Ti alloys do not have the same color as teeth, so they are inferior to ceramics and polymers in terms of aesthetic properties. In a previous study, Ti-29Nb-13Ta-4.6Zr was coated with a white Ti oxide layer by heat treatment to improve its aesthetic properties. Shot-peening is a severe plastic deformation process and can introduce a large shear strain on the peened surface. In this study, the effects of shot-peening and atmospheric-pressure plasma on Ti-29Nb-13Ta-4.6Zr were investigated to form a white layer on the surface for dental applications.

Ternary superconductor ''NbTiTa'' for high field superfluid magnets

International Nuclear Information System (INIS)

McInturff, A.D.; Carson, J.; Larbalestier, D.; Lee, P.; McKinnel, J.; Kanithi, H.; McDonald, W.; O'Larey, P.

1990-06-01

The possibility exists to obtain a higher 'Hc 2 ' upper critical field in the NbTi system which is normally limited by a spin-orbit coupling term. The introduction of scattering reduces this coupling. The spin-orbit scattering rate is proportional to Z 4 and therefore leads logically to the introduction of a high atomic number element which is more or less similar with respect to all of the other properties, i.e., Tc. Previous studies have shown Tantalum to be an excellent choice. The present work represents an attempt to obtain a high current density, high field ternary magnet conductor (Jc (10T, 2K, ρeff = 10 -12 Ω-cm)) > 2000A/mm 2 . This goal was met, but the conductor was clearly not optimized

Study of transformation behavior in a Ti-4.4 Ta-1.9 Nb alloy

International Nuclear Information System (INIS)

Mythili, R.; Paul, V. Thomas; Saroja, S.; Vijayalakshmi, M.; Raghunathan, V.S.

2005-01-01

An alloy of composition Ti-4.4 wt.% Ta-1.9 wt.% Nb is being developed as a structural material for corrosion applications, as titanium and its alloys possess excellent corrosion resistance in many oxidizing media. The primary physical metallurgy database for the Ti-4.4 wt.% Ta-1.9 wt.% Nb alloy is being presented for the first time. Determination of the β transus, M s temperature and classification of the alloy have been carried out, employing a variety of microscopy techniques, X-ray diffraction (XRD), micro-hardness and differential scanning calorimetry (DSC). The β transition temperature or β transus determined using different experimental techniques was found to agree very well with evaluations based on empirical calculations. Based on chemistry and observed room temperature microstructure, the alloy has been classified as an α + β titanium alloy. The high temperature β transforms to either α' or α + β by a martensitic or Widmanstatten transformation. The mechanisms of transformation of β under different conditions and characteristics of different types of α have been studied and discussed in this paper

Corrosion resistance and in vitro response of laser-deposited Ti-Nb-Zr-Ta alloys for orthopedic implant applications.

Science.gov (United States)

Samuel, Sonia; Nag, Soumya; Nasrazadani, Seifollah; Ukirde, Vaishali; El Bouanani, Mohamed; Mohandas, Arunesh; Nguyen, Kytai; Banerjee, Rajarshi

2010-09-15

While direct metal deposition of metallic powders, via laser deposition, to form near-net shape orthopedic implants is an upcoming and highly promising technology, the corrosion resistance and biocompatibility of such novel metallic biomaterials is relatively unknown and warrants careful investigation. This article presents the results of some initial studies on the corrosion resistance and in vitro response of laser-deposited Ti-Nb-Zr-Ta alloys. These new generation beta titanium alloys are promising due to their low elastic modulus as well as due the fact that they comprise of completely biocompatible alloying elements. The results indicate that the corrosion resistance of these laser-deposited alloys is comparable and in some cases even better than the currently used commercially-pure (CP) titanium (Grade 2) and Ti-6Al-4V ELI alloys. The in vitro studies indicate that the Ti-Nb-Zr-Ta alloys exhibit comparable cell proliferation but enhanced cell differentiation properties as compared with Ti-6Al-4V ELI. (c) 2010 Wiley Periodicals, Inc.

Nb and Ta Co-Doped TiO2 Transparent Conductive Thin Films by Magnetron Sputtering: Fabrication, Structure, and Characteristics

Science.gov (United States)

Liu, Yang; Peng, Qian; Qiao, Yadong; Yang, Guang

2018-06-01

Nb and Ta co-doped anatase titanium dioxide (NTTO) nanocrystalline thin films were deposited on quartz and Si (100) substrates by RF magnetron sputtering. The influence of RF power on the growth, structure, morphology, and properties of the samples are discussed in detail. X-ray diffraction measurements show that the films are polycrystalline with anatase tetragonal structure, which is further confirmed by Raman spectroscopy analysis. Meanwhile, Raman spectroscopy results indicate that the peak width of E g(1) mode, which is directly correlated to the carrier density, changes obviously with RF power. It is found that the substitution of Nb5+ and Ta5+ at Ti site is significantly improved with the increase of RF power from 150 W to 210 W. For the sample deposited at 210 W, the optical transmittance is above 82% in the visible range and the electrical resistivity is as low as 1.3 × 10-3 Ω cm with carrier density of 1.1 × 1021 cm-3 and Hall mobility of 4.5 cm2 V-1 s-1. The optical and electrical properties of NTTO thin films can be compared to those of Nb or Ta doped anatase TiO2. However, co-doping with Nb and Ta gives a possible platform to complement the limitations of each individual dopant.

Performance of multifilamentary Nb3Sn under mechanical load

International Nuclear Information System (INIS)

Easton, D.S.; Schwall, R.E.

1976-01-01

The critical current of a commercial multifilamentary Nb 3 Sn conductor has been measured under the application of uniaxial tension at 4.2 K and following bending at room temperature. Significant reductions in J/subc/ are observed under uniaxial loading. Results are presented for a monolithic conductor manufactured by the bronze diffusion technique and for cable conductors formed by the tin-dip technique

Superconductivity of Hg3NbF6 and Hg3TaF6

International Nuclear Information System (INIS)

Datars, W.R.; Morgan, K.R.; Gillespie, R.J.

1983-01-01

Low-temperature ac susceptibility measurements show that two new metallic compounds, Hg 3 TaF 6 and Hg 3 NbF 6 , are superconductors with a critical temperature of 7.0 K. Critical fields are 20% higher in Hg 3 TaF 6 but the temperature dependence of the critical field of the compounds is very similar down to 1.35 K. The critical field extrapolated to T = 0 K is 0.17 T for Hg 3 TaF 6 and 0.13 T for Hg 3 NbF 6

Electron microscopy studies in a high corrosion resistant Ti-Ta-Nb alloy

International Nuclear Information System (INIS)

Mythili, R.; Saroja, S.; Vijayalakshmi, M.

2010-01-01

Electron microscopy has played an important role in the indigenous development of Ti-5Ta-1.8Nb, an α+β alloy, for reprocessing applications. TEM was used to study the Widmanstatten, martensitic, and the omega phase transformations in the system. A wide spectrum of phase transformations could be introduced into the system, by modifying the composition of the β phase and the cooling rate. PEELS was used to understand the corrosion mechanism, by characterizing the passive film after the corrosion reactions

A method for decreasing transport ac losses in multifilamentary and multistrip superconductors

Energy Technology Data Exchange (ETDEWEB)

Glowacki, B A [Department of Materials Science and Metallurgy, University of Cambridge, Pembroke Street, Cambridge CB2 3QZ (United Kingdom); IRC in Superconductivity, University of Cambridge, Madingley Road, Cambridge CB3 0HE (United Kingdom); Majoros, M [IRC in Superconductivity, University of Cambridge, Madingley Road, Cambridge CB3 0HE (United Kingdom)

2000-07-01

A new method is proposed for decreasing transport ac losses in multifilamentary superconductors by the decoupling of the filaments using a magnetic material in the form of thin layers surrounding the individual filaments. For a superconductor with an elliptical cross section, the magnetic material surrounding the filaments affects the local magnetic field distribution that both reduces the critical current of the filaments and induces the transport ac losses in the magnetic material. Even by taking into account any detrimental influences of the presence of the magnetic material around the filaments, the analysis of the experimental data supported by computer modelling confirmed that for a Bi2223 tape with 100 filaments individually covered by magnetic material, such as iron powder, the transport ac losses should be 65 times lower than for the same multifilamentary conductor without the magnetic coating on the filaments. With an increasing number of filaments, the ac loss decrease would be even larger. (author)

Studies on advanced superconductors for fusion device. Pt. 2. Metallic superconductors other than Nb{sub 3}Sn

Energy Technology Data Exchange (ETDEWEB)

Tachikawa, K.; Yamamoto, J.; Mito, T. [eds.

1997-03-01

A comprehensive report on the present status of the development of Nb{sub 3}Sn superconductors was published as the NIFS-MEMO-20 in March, 1996 (Part 1 of this report series). The second report of this study covers various progress so far achieved in the research and development on advanced metallic superconductors other than Nb{sub 3}Sn. Among different A15 crystal-type compounds, Nb{sub 3}Al has been fabricated into cables with large current-carrying capacity for fusion device referring its smaller sensitivity to mechanical strain than Nb{sub 3}Sn. Other high-field A15 superconductors, e.g. V{sub 3}Ga, Nb{sub 3}Ge and Nb{sub 3}(Al,Ge), have been also fabricated through different novel processes as promising alternatives to Nb{sub 3}Sn conductors. Meanwhile, B1 crystal-type NbN and C15 crystal-type V{sub 2}(Hf,Zr) high-field superconductors are characterized by their excellent tolerance to mechanical strain and neutron irradiation. Chevrel-type PbMo{sub 6}S{sub 8} compound has gained much interests due to its extremely high upper critical field. In addition, this report includes the recent progress in ultra-fine filamentary NbTi wires for AC use, and that in NbTi/Cu magnetic shields necessary in the application of high magnetic field. The data on the decay of radioactivity in a variety of metals relating to fusion superconducting magnet are also attached as appendices. We hope that this report might contribute substantially as a useful reference for the planning of fusion apparatus of next generation as well as that of other future superconducting devices. (author)

Low-field Instabilities in Nb$_{3}$Sn Multifilamentary Wires the Possible Role of Unreacted Nb

CERN Document Server

Devred, A; Celentano, G; Fabbricatore, P; Ferdeghini, C; Greco, M; Gambardella, U

2007-01-01

We report an experimental study aiming to demonstrate the not negligible role of unreacted Nb on the magnetic instabilities in superconducting Nb$_{3}$Sn multifilamentary wires, observable through partial flux jumps at magnetic field values below 0.5 T. The analysed wires were recently developed for use as dipoles required in future high-energy proton accelerators and are based on powder-in-tube technology. We studied both unreacted (only involving Nb filaments) and reacted wires, finding flux jump instabilities in both cases when performing magnetic measurements. The results can be interpreted on the basis of the critical state model and are coherent with the intrinsic stability criterion.

Performance of multifilamentary Nb3Sn under mechanical load

International Nuclear Information System (INIS)

Easton, D.S.; Schwall, R.E.

1976-11-01

The critical current density of commercial multifilamentary Nb 3 Sn conductor has been measured during the application of uniaxial tension at 4.2 0 K and after bending at room temperature. Significant reductions in the critical current density J/sub c/ occurred under uniaxial loading. Results are presented for a monolithic conductor manufactured by the bronze diffusion technique and for cable conductors formed by the tin-dip technique

High-pressure phases of Weyl semimetals NbP, NbAs, TaP, and TaAs

Science.gov (United States)

Guo, ZhaoPeng; Lu, PengChao; Chen, Tong; Wu, JueFei; Sun, Jian; Xing, DingYu

2018-03-01

In this study, we used the crystal structure search method and first-principles calculations to systematically explore the highpressure phase diagrams of the TaAs family (NbP, NbAs, TaP, and TaAs). Our calculation results show that NbAs and TaAs have similar phase diagrams, the same structural phase transition sequence I41 md→ P6¯ m2→ P21/ c→ Pm3¯ m, and slightly different transition pressures. The phase transition sequence of NbP and TaP differs somewhat from that of NbAs and TaAs, in which new structures emerge, such as the Cmcm structure in NbP and the Pmmn structure in TaP. Interestingly, we found that in the electronic structure of the high-pressure phase P6¯ m2-NbAs, there are coexistingWeyl points and triple degenerate points, similar to those found in high-pressure P6¯ m2-TaAs.

Radiation-induced changes of critical fields in NbTi superconductors

International Nuclear Information System (INIS)

Weber, H.W.; Khier, W.; Wacenovsky, M.; Hoch, H.

1988-01-01

Neutron irradiation experiments on a variety of metallurgically different NbTi superconductors for use in fusion magnets were performed. Results on the change in critical current densities with neutron fluence were significantly different in low and in high magnetic fields. Based on the suggestion of a prevailing influence of the upper critical field on critical currents at high fields a systematic study of upper critical fields was made on irradiated and unirradiated samples. The upper critical field decreased upon irradiation by about 2 to 6%. Companion experiments on the change of the transition temperature in the same materials showed excellent correlations between the degradation of these superconductive properties. Implications for the observed critical current density degradation at high fields are discussed

Superconductors by powder metallurgy techniques

International Nuclear Information System (INIS)

Pickus, M.R.; Wang, J.L.F.

1976-05-01

Fabrication methods for Nb 3 Sn type compounds are described. Information is included on the Bell Telephone process, the General Electric tape process, superconductor stability, the bronze process, powder metallurgy multifilamentary tapes and wires, and current assessment of powder metallurgy superconducting wire

Considerations in designing and using superconductors with high resistivity matrices

International Nuclear Information System (INIS)

Bartlett, R.J.; Carlson, R.V.; Laquer, H.L.; Migliori, A.

1976-01-01

Superconductors are often designed with matrices of much higher residual resistivities than copper for reasons of manufacturing (multifilamentary Nb 3 Sn in CuSn bronze) or loss reduction (mixed matrix NbTi with Cu and CuNi). The high resistivity matrix may complicate or degrade contact resistances at the joints, generate excess heat, reduce the stability of the conductor, and interfere with the observation of flux flow resistivities in the 10 -12 Ω-cm region. The minimization of these effects is discussed, presenting both simple and more refined models for the current transfer length, and it is shown how variations in transfer length (with current), particularly under significant self field conditions, can mimic flux flow resistivity

Microstructure characteristics and mechanical properties of laser-TIG hybrid welded dissimilar joints of Ti-22Al-27Nb and TA15

Science.gov (United States)

Zhang, Kezhao; Lei, Zhenglong; Chen, Yanbin; Liu, Ming; Liu, Yang

2015-10-01

Laser-TIG-hybrid-welding (TIG - tungsten inert gas) process was successfully applied to investigate the microstructure and tensile properties of Ti-22Al-27Nb/TA15 dissimilar joints. The HAZ of the arc zone in Ti-22Al-27Nb was characterized by three different regions: single B2, B2+α2 and B2+α2+O, while the single B2 phase region was absent in the HAZ of the laser zone. As for the HAZ in TA15 alloy, the microstructure mainly contained acicular α‧ martensites near the fusion line and partially remained the lamellar structure near the base metal. The fusion zone consisted of B2 phase due to the relatively high content of β phase stabilizing elements and fast cooling rate during the welding process. The tensile strength of the welds was higher than that of TA15 alloy because of the fully B2 microstructure in the fusion zone, and the fracture preferentially occurred on the base metal of TA15 alloy during the tensile tests at room temperature and 650 °C.

Structure and Properties of Ti-19.7Nb-5.8Ta Shape Memory Alloy Subjected to Thermomechanical Processing Including Aging

Science.gov (United States)

Dubinskiy, S.; Brailovski, Vladimir; Prokoshkin, S.; Pushin, V.; Inaekyan, K.; Sheremetyev, V.; Petrzhik, M.; Filonov, M.

2013-09-01

In this work, the ternary Ti-19.7Nb-5.8Ta (at.%) alloy for biomedical applications was studied. The ingot was manufactured by vacuum arc melting with a consumable electrode and then subjected to hot forging. Specimens were cut from the ingot and processed by cold rolling with e = 0.37 of logarithmic thickness reduction and post-deformation annealing (PDA) between 400 and 750 °C (1 h). Selected samples were subjected to aging at 300 °C (10 min to 3 h). The influence of the thermomechanical processing on the alloy's structure, phase composition, and mechanical and functional properties was studied. It was shown that thermomechanical processing leads to the formation of a nanosubgrained structure (polygonized with subgrains below 100 nm) in the 500-600 °C PDA range, which transforms to a recrystallized structure of β-phase when PDA temperature increases. Simultaneously, the phase composition and the β → α″ transformation kinetics vary. It was found that after conventional cold rolling and PDA, Ti-Nb-Ta alloy manifests superelastic and shape memory behaviors. During aging at 300 °C (1 h), an important quantity of randomly scattered equiaxed ω-precipitates forms, which results in improved superelastic cyclic properties. On the other hand, aging at 300 °C (3 h) changes the ω-precipitates' particle morphology from equiaxed to elongated and leads to their coarsening, which negatively affects the superelastic and shape memory functional properties of Ti-Nb-Ta alloy.

Costs of magnets for large fusion power reactors: Phase I, cost of superconductors for dc magnets

International Nuclear Information System (INIS)

Powell, J.R.

1972-01-01

Projections are made for dc magnet conductor costs for large fusion power reactors. A mature fusion economy is assumed sometime after 2000 A. D. in which approximately 90,000 MW(e) of fusion reactors are constructed/year. State of the art critical current vs. field characteristics for superconductors are used in these projections. Present processing techniques are used as a basis for the design of large plants sized to produce approximately one-half of the conductor needed for the fusion magnets. Multifilamentary Nb-Ti, Pb-Bi in glass fiber, GE Nb 3 Sn tape, Linde plasma sprayed Nb 3 Sn tape, and V 3 Ga tape superconductors are investigated, together with high purity aluminum cryoconductor. Conductor costs include processing costs [capital (equipment plus buildings), labor, and operating] and materials costs. Conductor costs are compared for two sets of material costs: current (1971 A. D.) costs, and projected (after 2000 A. D.) costs. (U.S.)

Emergence of Nb-Ti as supermagnet material

Energy Technology Data Exchange (ETDEWEB)

Berlincourt, T G

1987-06-01

The discovery and emergence of Nb-Ti as a high field superconductor are reviewed. The prehistory and setting for its discovery are described, and an anecdotal history follows its development up to the first successful large scale applications.

Emergence of Nb-Ti as supermagnet material

International Nuclear Information System (INIS)

Berlincourt, T.G.

1987-01-01

The discovery and emergence of Nb-Ti as a high field superconductor are reviewed. The prehistory and setting for its discovery are described, and an anecdotal history follows its development up to the first successful large scale applications. (author)

Electrochemical characterization of pulsed layer deposited hydroxyapatite-zirconia layers on Ti-21Nb-15Ta-6Zr alloy for biomedical application

Energy Technology Data Exchange (ETDEWEB)

Izquierdo, Javier [Department of Chemistry, Universidad de La Laguna, P.O. Box 456, E-38200 La Laguna, Tenerife (Spain); Bolat, Georgiana [“Gheorghe Asachi” Technical University of Iasi, Faculty of Chemical Engineering and Environmental Protection, 73 Prof. Dr. Doc. D. Mangeron Street, 700050 Iasi (Romania); Cimpoesu, Nicanor [“Gheorghe Asachi” Technical University of Iasi, Faculty of Materials Science, 61-63 Prof. Dr. Doc. D. Mangeron Street, 700050 Iasi (Romania); Trinca, Lucia Carmen [Science Department, University of Agricultural Sciences and Veterinary Medicine, M. Sadoveanu Alley 3, 700490 Iasi (Romania); Mareci, Daniel, E-mail: danmareci@yahoo.com [“Gheorghe Asachi” Technical University of Iasi, Faculty of Chemical Engineering and Environmental Protection, 73 Prof. Dr. Doc. D. Mangeron Street, 700050 Iasi (Romania); Souto, Ricardo Manuel, E-mail: rsouto@ull.es [Department of Chemistry, Universidad de La Laguna, P.O. Box 456, E-38200 La Laguna, Tenerife (Spain); Institute of Material Science and Nanotechnology, Universidad de La Laguna, E-38200 La Laguna, Tenerife (Spain)

2016-11-01

Highlights: • New quarternary Ti-based alloy for biomaterial application. • Combined hydroxyapatite-zirconia coating produced by pulsed laser deposition. • Porous layer formed on the coated alloy blocks electron transfer reactions. • Electrochemical behaviour consistent with passive film with duplex structure. • HA–ZrO{sub 2} coated Ti-21Nb-15Ta-6Zr exhibits high potential for osseointegration. - Abstract: A new titanium base Ti-21Nb-15Ta-6Zr alloy covered with hydroxyapatite-zirconia (HA–ZrO{sub 2}) by pulsed laser deposition (PLD) technique was characterized regarding its corrosion resistance in simulated physiological Ringer’s solution at 37 °C. For the sake of comparison, Ti-6Al-4V standard implant alloy, with and without hydroxyapatite-zirconia coating, was also characterized. Multiscale electrochemical analysis using both conventional averaging electrochemical techniques, namely electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization, and spatially-resolved microelectrochemical techniques (scanning electrochemical microscopy, SECM) were used to investigate the electrochemical behaviour of the materials. In addition, scanning electron microscopy evidenced that no relevant surface morphology changes occurred on the materials upon immersion in the simulated physiological solution, despite variations in their electrochemical behaviour. Although uncoated metals appear to show better performances during conventional corrosion tests, the response is still quite similar for the HA–ZrO{sub 2} coated materials while providing superior resistance towards electron transfer due to the formation of a more dense film on the surface, thus effectively behaving as a passive material. It is believed corrosion of the HA–ZrO{sub 2} coated Ti-21Nb-15Ta-6Zr alloy will have negligible effect upon biochemical and cellular events at the bone-implant interface and could facilitate osseointegration.

In vitro bio-functional performances of the novel superelastic beta-type Ti-23Nb-0.7Ta-2Zr-0.5N alloy.

Science.gov (United States)

Ion, Raluca; Gordin, Doina-Margareta; Mitran, Valentina; Osiceanu, Petre; Dinescu, Sorina; Gloriant, Thierry; Cimpean, Anisoara

2014-02-01

The materials used for internal fracture fixations and joint replacements are mainly made of metals which still face problems ranging from higher rigidity than that of natural bone to leaching cytotoxic metallic ions. Beta (β)-type titanium alloys with low elastic modulus made from non-toxic and non-allergenic elements are desirable to reduce stress shielding effect and enhance bone remodeling. In this work, a new β-type Ti-23Nb-0.7Ta-2Zr-0.5N alloy with a Young's modulus of approximately 50 GPa was designed and characterized. The behavior of MC3T3-E1 pre-osteoblasts on the new alloy, including adhesion, proliferation and differentiation, was evaluated by examining the cytoskeleton, focal adhesion formation, metabolic activity and extracellular matrix mineralization. Results indicated that the pre-osteoblast cells exhibited a similar degree of attachment and growth on Ti-23Nb-0.7Ta-2Zr-0.5N and Ti-6Al-4V. However, the novel alloy proved to be significantly more efficient in sustaining mineralized matrix deposition upon osteogenic induction of the cells than Ti-6Al-4V control. Further, the analysis of RAW 264.7 macrophages cytokine gene and protein expression indicated no significant inflammatory response. Collectively, these findings suggest that the Ti-23Nb-0.7Ta-2Zr-0.5N alloy, which has an increased mechanical biocompatibility with bone, allows a better osteogenic differentiation of osteoblast precursor cells than Ti-6Al-4V and holds great potential for future clinical prosthetic applications. Copyright © 2013 Elsevier B.V. All rights reserved.

Volume pinning force and upper critical field of irradiated Nb3Sn

International Nuclear Information System (INIS)

Maier, P.; Seibt, E.

1981-01-01

Irradiation by neutrons and ions in A15 superconductors (Nb 3 Sn, V 3 Ga) exerts a stronger influence on the pinning behavior than in nonordered alloys (NbTi). In this work it is shown for deuteron irradiated Nb 3 /Sn wires prepared by the bronze process that the dose curve of the volume pinning force P/sub V/ can be conveniently described by a sum of two terms, due to the grain boundary pinning and to the radiation pinning, respectively. After deduction of the contribution by the radiation-induced pinning centers, good agreement is obtained between the measured P/sub V/ values and those calculated using the upper critical field B/sub c/2 and the transition temperature T/sub c/ on the basis of the irradiation fluence. The use of a theoretical relationship between B/sub c/2 and T/sub c/ is supported by measured values. Application to multifilamentary superconductors with high current carrying capabilities simplifies the calculation of P/sub V/, since the radiation induced volume pinning force can be neglected

Phase Composition of a CrMo0.5NbTa0.5TiZr High Entropy Alloy: Comparison of Experimental and Simulated Data

OpenAIRE

Fan Zhang; Oleg N. Senkov; Jonathan D. Miller

2013-01-01

Microstructure and phase composition of a CrMo0.5NbTa0.5TiZr high entropy alloy were studied in the as-solidified and heat treated conditions. In the as-solidified condition, the alloy consisted of two disordered BCC phases and an ordered cubic Laves phase. The BCC1 phase solidified in the form of dendrites enriched with Mo, Ta and Nb, and its volume fraction was 42%. The BCC2 and Laves phases solidified by the eutectic-type reaction, and their volume fractions were 27% and 31%, respectively....

Further investigations of the upper critical field and the high field critical current density in Nb-Ti and its alloys

International Nuclear Information System (INIS)

Hawksworth, D.G.; Larbalestier, D.C.

1980-09-01

This paper reports further measurements of Hc 2 in the Nb-Ti-Ta and Nb-Ti-Hf systems. Whilst we find only small enhancements of approx. 0.3 Tesla in μ 0 Hc 2 (4.2 0 K) compared to binary Nb-Ti, at 2 0 K there is a wide composition range in the Nb-Ti-Ta system where μ 0 Hc 2 (2 0 K) exceeds 15 Tesla, reaching a maximum of 15.5 Tesla. This represents an enhancement of 1.3 Tesla over unalloyed Nb-Ti. By comparison alloys in the Nb-Ti-Hf system show a maximum enhancement in μ 0 Hc 2 (2 0 K) of only 0.3 Tesla. The reasons both for the enhancements in Hc 2 and for the differences in behavior shown by alloys containing Ta and Hf are briefly discussed. This paper also discusses common features in the behavior of the high field critical current density, J/sub c/, of four commercial Nb-Ti composites and upon the basis of this behavior predict the enhancements in high field J/sub c/ to be expected from using Nb-Ti-Ta and its alloys

Direct observation of the growth of voids in multifilamentary superconducting materials via hot stage scanning electron microscopy

International Nuclear Information System (INIS)

Wang, J.L.F.; Holthuis, J.T.; Pickus, M.R.; Lindberg, R.W.

1978-11-01

The need for large high field magnetic devices has focused attention on multifilamentary superconductors based on A15 compounds such as Nb 3 Sn. The commercial bronze process for fabricating multifilamentary superconducting Nb 3 Sn wires was developed. A major problem is strain sensitivity when long reaction times are employed. An improved hot stage for the scanning electron microscope was constructed to study the formation of the A15 phase by solid state diffusion. The nucleation and growth of voids near the interface of the A15 phase (Nb 3 Sn) and matrix were observed, monitored, and recorded on video tape. Successive layers of material heated in the hot stage were subsequently removed and the new surfaces were re-examined, using SEM-EDX and optical microscopy, to confirm the fact that the observed porosity was indeed a bulk rather than a surface phenomenon. These voids are considered to be a primary cause for degrading the mechanical, thermal and superconducting properties

First principles study the stability and mechanical properties of MC (M = Ti, V, Zr, Nb, Hf and Ta) compounds

International Nuclear Information System (INIS)

Liu, YangZhen; Jiang, YeHua; Zhou, Rong; Feng, Jing

2014-01-01

Highlights: • The stability and elastic constants of carbides are studied by first principles. • The rules of modulus of MC compounds are discussed by their group. • The hardness of carbides is estimated in this paper at the first time. -- Abstract: The first principles calculations based on density functional theory (DFT) were adopted to investigate the stability, elastic constants, chemical bonding, Debye temperature and hardness of MC (M = Ti, V, Zr, Nb, Hf and Ta) compounds. The cohesive energy and formation enthalpy of these carbides indicate that they are thermodynamically stable structures. The population analysis was used to discuss the chemical bonding of these carbides. The elastic constants and moduli of these compounds were calculated. The results show that the bulk moduli of the carbides of transition metals from the fourth group (TiC, ZrC, HfC) are lower than the fifth group (VC, NbC, TaC). However, the Young’s moduli of the carbides from fourth group are higher than the fifth group. The hardness of compounds was estimated using a semi empirical hardness theory

Behavior of A NbTi very fine filament composite with current feed in the technical range

International Nuclear Information System (INIS)

Asdente, M.; Ottoboni, V.; Ripamonti, G.; Zannella, S.

1985-01-01

Self-field losses have been measured on a NbTi multifilamentary wire with very fine filaments suitable for use in ac superconducting equipment working at industrial frequency. The loss trends as functions of current intensity and frequency as well as the comparison of the losses in a coil show that they are essentially of hysteretic nature

Low-temperature deuteron irradiation of differently reacted Nb3Sn superconductors

International Nuclear Information System (INIS)

Maier, P.; Seibt, E.

1978-01-01

Irradiation measurements with 50 MeV deuterons at 18 K and subsequent annealing measurements were performed on Nb 3 Sn single and multifilamentary superconductors at the Helium-Bath Irradiation Facility of the Karlsruhe Cyclotron. The critical current densities jsub(c) of Nb 3 Sn bronze-reacted wire samples at various reaction temperatures (Tsub(R)=650,700,750,800 and 850 0 C) with equal layer thickness were measured for integral deuteron fluxes up to PHIsub(t)=0.7x10 18 cm -2 . After a decrease in jsub(c) of 85% at maximum dose a relatively small annealing effect (4 to 10%) was observed at ambient temperatures. The maximum value of the normalized critical current density, jsub(c)/jsub(c0), at PHIsub(t)approximately=10 17 cm -2 increases with increasing reaction temperature. The difference in volume pinning forces before and after irradiation increases less than linear (approximately√PHIsub(t)) with the irradiation dose. An almost linear dependence between the inverse grain diameter (dsub(K) -1 )) and volume pinning force is obtained both before and after irradiation. (Auth.)

Experimental investigation of copper matrix longitudinal resistance in a composite Nb-Ti wire

International Nuclear Information System (INIS)

Gubkin, I.N.; Kozlenkova, N.I.; Nikulin, A.D.; Polikarpova, M.V.; Filkin, V.Ya.

1994-01-01

The longitudinal resistance of multifilamentary superconducting wires is among the major parameters used in design and optimization of superconducting magnetic systems. To enhance the conductivity of the copper matrix, it is made of pipes and rods of enhanced quality copper produced by electron beam melting (resistance ratio between two temperatures, 295 K and 4.2 K, R 295 /R 4.2 > 200). Yet for readily obtainable conductors this parameter is much lower. The reduction of the copper-matrix electrical conductivity may be attributed to wire-production technology involving processes such as extrusion, drawing and intermediate thermal processing, as well as to the size effect. Copper-matrix longitudinal resistance was studied as a function of wire diameter on specimens of multifilamentary Nb-Ti wire with filaments coated by a Nb layer. Experimental results are compared with the Sondheimer calculations for a monofilament conductor as well as with the Gavalloni calculations for an ideal wire with hexagonally located filaments. It has been shown that the best fit with the experiment is provided by the Sondheimer approximation. Comparison of the results of this work with other authors' data obtained for the specimens with no niobium barrier, allows the authors to single out the influence of a pure size effect and diffusion of Ti on the resistivity

α″ Martensite and Amorphous Phase Transformation Mechanism in TiNbTaZr Alloy Incorporated with TiO2 Particles During Friction Stir Processing

Science.gov (United States)

Ran, Ruoshi; Liu, Yiwei; Wang, Liqiang; Lu, Eryi; Xie, Lechun; Lu, Weijie; Wang, Kuaishe; Zhang, Lai-Chang

2018-06-01

This work studied the formation of the α″ martensite and amorphous phases of TiNbTaZr alloy incorporated with TiO2 particles during friction stir processing. Formation of the amorphous phase in the top surface mainly results from the dissolution of oxygen, rearrangement of the lattice structure, and dislocations. High-stress stemming caused by dislocations and high-stress concentrations at crystal-amorphous interfaces promote the formation of α″ martensite. Meanwhile, an α″ martensitic transformation is hindered by oxygen diffusion from TiO2 to the matrix, thereby increasing resistance to shear.

Moderation of flux jumps dynamics by eddy-currents in a disk shape NbTi superconductor

International Nuclear Information System (INIS)

Vasiliev, S.; Nabialek, A.; Piechota, S.; Szymczak, H.; Chabanenko, V.V.; Rusakov, V.

2004-01-01

We studied the moderation of the flux jumps dynamics in a disc shape NbTi-50% superconductor caused by eddy-currents induced in two copper cylinders attached to both surfaces of the investigated sample. We investigated experimentally the time of the flux jump duration, amount of the magnetic flux entering the sample during the jump as well as the sine structure of the jumps as a function of temperature and the external magnetic field. A simple theoretical model, which describes the magnetic field dependence of the amount of the magnetic flux entering the superconducting sample during the flux jump, was developed. (author)

Phase Composition of a CrMo0.5NbTa0.5TiZr High Entropy Alloy: Comparison of Experimental and Simulated Data

Directory of Open Access Journals (Sweden)

Fan Zhang

2013-09-01

Full Text Available Microstructure and phase composition of a CrMo0.5NbTa0.5TiZr high entropy alloy were studied in the as-solidified and heat treated conditions. In the as-solidified condition, the alloy consisted of two disordered BCC phases and an ordered cubic Laves phase. The BCC1 phase solidified in the form of dendrites enriched with Mo, Ta and Nb, and its volume fraction was 42%. The BCC2 and Laves phases solidified by the eutectic-type reaction, and their volume fractions were 27% and 31%, respectively. The BCC2 phase was enriched with Ti and Zr and the Laves phase was heavily enriched with Cr. After hot isostatic pressing at 1450 °C for 3 h, the BCC1 dendrites coagulated into round-shaped particles and their volume fraction increased to 67%. The volume fractions of the BCC2 and Laves phases decreased to 16% and 17%, respectively. After subsequent annealing at 1000 °C for 100 h, submicron-sized Laves particles precipitated inside the BCC1 phase, and the alloy consisted of 52% BCC1, 16% BCC2 and 32% Laves phases. Solidification and phase equilibrium simulations were conducted for the CrMo0.5NbTa0.5TiZr alloy using a thermodynamic database developed by CompuTherm LLC. Some discrepancies were found between the calculated and experimental results and the reasons for these discrepancies were discussed.

A review and prospects for Nb3Sn superconductor development

Science.gov (United States)

Xu, Xingchen

2017-09-01

Nb3Sn superconductors have significant applications in constructing high-field (>10 T) magnets. This article briefly reviews development of Nb3Sn superconductor and proposes prospects for further improvement. It is shown that significant improvement of critical current density (J c) is needed for future accelerator magnets. After a brief review of the development of Nb3Sn superconductors, the factors controlling J c are summarized and correlated with their microstructure and chemistry. The non-matrix J c of Nb3Sn conductors is mainly determined by three factors: the fraction of current-carrying Nb3Sn phase in the non-matrix area, the upper critical field B c2, and the flux line pinning capacity. Then prospects to improve the three factors are discussed respectively. An analytic model was developed to show how the ratios of precursors determine the phase fractions after heat treatment, based on which it is predicted that the limit of current-carrying Nb3Sn fraction in subelements is ∼65%. Then, since B c2 is largely determined by the Nb3Sn stoichiometry, a thermodynamic/kinetic theory is presented to show what essentially determines the Sn content of Nb3Sn conductors. This theory explains the influences of Sn sources and Ti addition on stoichiometry and growth rate of Nb3Sn layers. Next, to improve flux pinning, previous efforts in this community to introduce additional pinning centers to Nb3Sn wires are reviewed, and an internal oxidation technique is described. Finally, prospects for further improvement of non-matrix J c of Nb3Sn conductors are discussed, and it is seen that the only opportunity for further significantly improving J c lies in improving flux pinning.

Texture and superelastic behavior of cold-rolled TiNbTaZr alloy

International Nuclear Information System (INIS)

Wang Liqiang; Lu Weijie; Qin Jining; Zhang Fan; Zhang Di

2008-01-01

This work investigates the deformation texture and strain-induced α'' martensite texture of TiNbTaZr alloy during cold rolling. The alloy is rolled by 20% and 90% reductions without changing rolling direction. Textures of cold-rolled specimens are investigated by X-ray diffraction measurements. Besides {2 2 1} β β twinning texture, {1 0 0} β β texture is developed in the specimen with 20% reduction. In the 90% cold-rolled specimen, {1 0 0} β β texture appears along rolling direction and strain-induced α'' martensite texture tends to [0 1 0] and [0 0 1] directions along rolling direction (RD) and transverse direction (TD), respectively. Superelastic strain (ε SE ) exhibits higher value along RD and TD. Pure elastic strain (ε E ) shows higher value along RD and 45 deg. from RD

Structure and magnetic properties of NdFeB thin films with Cr, Mo, Nb, Ta, Ti, and V buffer layers

International Nuclear Information System (INIS)

Jiang, H.; O'Shea, M.J.

2000-01-01

Layers of NdFeB of the form A(20 nm)/NdFeB(d nm)/A(20 nm) where A represents Cr, Mo, Nb, Ta, Ti, V were prepared on a silicon substrate by magnetron sputtering. The purpose is to determine how (i) the chosen buffer layer and (ii) NdFeB layer thickness d (especially d 2 Fe 14 B with no preferred crystalline orientation. Our highest coercivities occur for buffer layer elements from row five of the periodic table, 20 kOe (1600 kA/m) in a Nb buffered sample with d of 180 nm and 17 kOe (1350 kA/m) in a Mo buffered sample with d of 180 nm. Buffer layers from row four (Ti, V, and Cr) and row six (Ta) all give lower coercivities. Our largest energy product, 10.3 MG-Oe (82 kJ/m 3 ), is obtained for the Mo buffered sample. Average Nd 2 Fe 14 B crystallite size for this sample is 27 nm. Only the Cr and Ti buffered films show a large coercivity (≥2 kOe) for d of 54 nm with the Cr films showing the highest coercivity, 2.7 kOe (215 kA/m). In films subjected to a rapid thermal anneal (anneal time 30 s) we find that both the coercivity and energy product are larger than in samples subjected to a 20 min anneal. In our Nb buffered systems we obtain coercivities as high as 26.3 kOe (2090 kA/m) after a rapid thermal anneal

Comparative Study of Heat Transfer from Nb-Ti and Nb$_3$Sn coils to He II

CERN Document Server

La China, M

2008-01-01

In superconducting magnets, the energy deposited or generated in the coil must be evacuated to prevent temperature rise and consequent transition of the superconductor to the resistive state. The main barrier to heat extraction is represented by the electric insulation wrapped around superconducting cables. In the LHC, insulation improvement is a key point in the development of interaction region magnets and injector chain fast-pulsed magnets for luminosity upgrade; the high heat load of these magnets, in fact, is not compatible with the use of current insulation schemes. We review the standard insulation schemes for Nb-Ti and Nb$_{3}$Sn technology from the thermal point of view. We implement, in an analytical model, the strongly nonlinear thermal resistances of the different coil components including the permeability to superfluid helium of Nb-Ti insulations, measured during the LHC main dipole development. We use such a model to compare Nb-Ti and Nb$_{3}$Sn technologies by taking into account their specific...

Experiment to measure the effects of biaxial strain on the critical current of NbTi superconductor

International Nuclear Information System (INIS)

Froelich, K.J.

1975-01-01

Twisted multifilament, copper-clad NbTi superconductors have been axially and biaxially strained at 4.2K with a 7.5T background field. A simply-constructed cryogenic loading frame was built and used to strain the conductor. Results on 1.27 mm x 3.13 mm conductor have shown that degradation of less than .3 percent of critical current occurred when the wire was biaxially strained to +3260 μepsilon in the axial direction and -1875 μepsilon in the transverse direction. Degradation approaches 3 percent of critical current at approximately 6000 μepsilon in the axial direction only

The superconductor

International Nuclear Information System (INIS)

Lad, J.K.

1979-01-01

Techniques for fabrication of a few important superconductors like Nb, Ti and Nb 3 Sn are described. Copper or bronze or both can be used as a matrix in the superconductor. Current densities obtained for different ratios of copper to superconductor are studied. The specifications of multi-filament Nb 3 Sn superconductors are given. The relative merits of the two superconductors are discussed. The temperature range obtained is approximately 3 0 K and a magnetic field of 9T(tesla) can be achieved. (A.K.)

Comparative study of heat transfer from Nb-Ti and Nb_{3}Sn coils to He II

Directory of Open Access Journals (Sweden)

Marco La China

2008-08-01

Full Text Available In superconducting magnets, the energy deposited or generated in the coil must be evacuated to prevent temperature rise and consequent transition of the superconductor to the resistive state. The main barrier to heat extraction is represented by the electric insulation wrapped around superconducting cables. In the LHC, insulation improvement is a key point in the development of interaction region magnets and injector chain fast-pulsed magnets for luminosity upgrade; the high heat load of these magnets, in fact, is not compatible with the use of current insulation schemes. We review the standard insulation schemes for Nb-Ti and Nb_{3}Sn technology from the thermal point of view. We implement, in an analytical model, the strongly nonlinear thermal resistances of the different coil components including the permeability to superfluid helium of Nb-Ti insulations, measured during the LHC main dipole development. We use such a model to compare Nb-Ti and Nb_{3}Sn technologies by taking into account their specific operating margin in different working conditions. Finally, we propose an insulation scheme to enhance the heat transfer capability of Nb-Ti coils.

Porous Nb-Ti-Ta alloy scaffolds for bone tissue engineering: Fabrication, mechanical properties and in vitro/vivo biocompatibility.

Science.gov (United States)

Liu, Jue; Ruan, Jianming; Chang, Lin; Yang, Hailin; Ruan, Wei

2017-09-01

Porous Nb-Ti-Ta (at.%) alloys with the pore size of 100-600μm and the porosity of 50%-80% were fabricated by the combination of the sponge impregnation technique and sintering method. The results revealed that the pores were well connected with three-dimensional (3D) network structure, which showed morphological similarity to the anisotropic porous structure of human bones. The results also showed that the alloys could provide the compressive Young's modulus of 0.11±0.01GPa to 2.08±0.09GPa and the strength of 17.45±2.76MPa to 121.67±1.76MPa at different level of porosity, indicating that the mechanical properties of the alloys are similar to those of human bones. Pore structure on the compressive properties was also discussed on the basis of the deformation mode. The relationship between compressive properties and porosity was well consistent with the Gibson-Ashby model. The mechanical properties could be tailored to match different requirements of the human bones. Moreover, the alloys had good biocompatibility due to the porous structure with higher surface, which were suitable for apatite formation and cell adhesion. In conclusion, the porous Nb-Ti-Ta alloy is potentially useful in the hard tissue implants for the appropriate mechanical properties as well as the good biocompatible properties. Copyright © 2017. Published by Elsevier B.V.

Energy and technology review

International Nuclear Information System (INIS)

Carr, R.B.

1975-12-01

Brief discussions are given on research work at the National CTR Computer Center at Livermore, high-field superconducting magnets for fusion reactors, and digital image processing for plasma diagnostics. Some developmental work on multifilamentary superconductors of Nb--Ti and Nb--Sn is described. Some complex mathematical techniques for enhancing and restoring digital images for plasma diagnostics are discussed

Voltage spikes in Nb3Sn and NbTi strands

International Nuclear Information System (INIS)

Bordini, B.; Ambrosio, G.; Barzi, E.; Carcagno, R.; Feher, S.; Kashikhin, V.V.; Lamm, M.J.; Orris, D.; Tartaglia, M.; Tompkins, J.C.; Turrioni, D.; Yamada, R.; Zlobin, A.V.; Fermilab

2005-01-01

As part of the High Field Magnet program at Fermilab several NbTi and Nb 3 Sn strands were tested with particular emphasis on the study of voltage spikes and their relationship to superconductor instabilities. The voltage spikes were detected under various experimental conditions using voltage-current (V-I) and voltage-field (V-H) methods. Two types of spikes, designated ''magnetization'' and ''transport current'' spikes, have been identified. Their origin is most likely related to magnetization flux jump and transport current redistribution, respectively. Many of the signals observed appear to be a combination of these two types of spikes; the combination of these two instability mechanisms should play a dominant role in determining the minimum quench current

Characterization and corrosion resistance of anodic electrodeposited titanium oxide/phosphate films on Ti-20Nb-10Zr-5Ta bioalloy

Energy Technology Data Exchange (ETDEWEB)

Popa, Monica; Vasilescu, Cora; Drob, Silviu I.; Osiceanu, Petre; Anastasescu, Mihai; Calderon-Moreno, Jose M., E-mail: josecalderonmoreno@yahoo.com [Institute of Physical Chemistry ' Ilie Murgulescu' of the Romanian Academy, Bucharest (Romania)

2013-07-15

In this work, the anodic galvanostatic electrodeposition of an oxidation film containing phosphates on Ti-20Nb-10Zr-5Ta alloy from orthophosphoric acid solution is presented. Its composition was determined by X-ray diffractometry (XRD), Fourier transform infrared spectroscopy (FTIR) and Raman micro-spectroscopy, and its topography by atomic force microscopy (AFM). The corrosion resistance of the coated alloy in simulated human fluid (by linear polarization method and monitoring of open circuit potentials, corresponding open circuit potential gradients) as well as the characterization of the coating (by Raman spectroscopy and depth profile X-ray photoelectron spectroscopy (XPS)) deposited in a period of 300 h soaking in simulated human body fluid were studied. The electrodeposited film was composed of amorphous titanium dioxide and contained phosphate groups. The corrosion resistance of the coated Ti-20Nb-10Zr-5Ta alloy in neutral and alkaline Ringer's solutions was higher than that of the bare alloy due to the protective properties of the electrodeposited film. The corrosion parameters improved over time as result of the thickening of the surface film by the deposition from the physiological solution. The deposited coating presented a variable composition in depth: at the deeper layer nucleated nanocrystalline hydroxyapatite and at the outer layer amorphous calcium phosphate. (author)

Characterization and corrosion resistance of anodic electrodeposited titanium oxide/phosphate films on Ti-20Nb-10Zr-5Ta bioalloy

International Nuclear Information System (INIS)

Popa, Monica; Vasilescu, Cora; Drob, Silviu I.; Osiceanu, Petre; Anastasescu, Mihai; Calderon-Moreno, Jose M.

2013-01-01

In this work, the anodic galvanostatic electrodeposition of an oxidation film containing phosphates on Ti-20Nb-10Zr-5Ta alloy from orthophosphoric acid solution is presented. Its composition was determined by X-ray diffractometry (XRD), Fourier transform infrared spectroscopy (FTIR) and Raman micro-spectroscopy, and its topography by atomic force microscopy (AFM). The corrosion resistance of the coated alloy in simulated human fluid (by linear polarization method and monitoring of open circuit potentials, corresponding open circuit potential gradients) as well as the characterization of the coating (by Raman spectroscopy and depth profile X-ray photoelectron spectroscopy (XPS)) deposited in a period of 300 h soaking in simulated human body fluid were studied. The electrodeposited film was composed of amorphous titanium dioxide and contained phosphate groups. The corrosion resistance of the coated Ti-20Nb-10Zr-5Ta alloy in neutral and alkaline Ringer's solutions was higher than that of the bare alloy due to the protective properties of the electrodeposited film. The corrosion parameters improved over time as result of the thickening of the surface film by the deposition from the physiological solution. The deposited coating presented a variable composition in depth: at the deeper layer nucleated nanocrystalline hydroxyapatite and at the outer layer amorphous calcium phosphate. (author)

Superconductor development program at Lawrence Livermore Laboratory

International Nuclear Information System (INIS)

Cornish, D.N.

1978-01-01

Winding of a Nb--Ti test coil at the Lawrence Livermore Laboratory is nearly complete. The conductor in this coil operates in a maximum field of 7.5 T and provides the 2-T field required by the Mirror Fusion Test Facility. Nb 3 Sn multifilamentary conductors, made using the ''bronze'' technique, appear capable of providing the higher fields needed by commercial reactors

Development of Ti-12Mo-3Nb alloy for biomedical application; Desenvolvimento da liga Ti-12Mo-3Nb para aplicacao biomedica

Energy Technology Data Exchange (ETDEWEB)

Panaino, J.V.P.; Gabriel, S.B., E-mail: josevicentepanaino@hotmail.co [Centro Universidade de Volta Redonda (UNIFOA), RJ (Brazil); Mei, P. [Universidade Estadual de Campinas (DEMa/UNICAMP), SP (Brazil). Dept. de Materiais; Brum, M.V. [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Programa de Engenharia Metalurgica e de Materiais; Nunes, C.A. [Universidade de Sao Paulo (EEL/USP), Lorena, SP (Brazil). Escola de Engenharia

2010-07-01

The titanium alloys are quite satisfactory for biomedical applications due to their physical, mechanical and biological properties. Recent studies focuses on the development of beta type titanium alloys, composed of toxic elements (Nb, Mo, Ta ,...), because they have more advantages than alpha and alpha + beta (Ti- 6Al-4V) alloys such as lower modulus of elasticity, better plasticity and, moreover, the process variables can be controlled to produce selected results. This project focused on the development and characterization of Ti-12Mo-3Nb alloy in the condition 'as cast' and after thermomechanical treatment. The material was characterized in different conditions by X-ray diffraction, optical microscopy, microhardness measurements and elasticity modulus. The results showed that the forged Ti-12Mo-3Nb alloy showed the best combination of properties, being a promising candidate for use as implant. (author)

Numerical simulation of mold shape’s influence on NbTi cold-pressing superconducting joint

Energy Technology Data Exchange (ETDEWEB)

Zhou, Feng, E-mail: zhoufeng@mail.iee.ac.cn; Cheng, Junsheng; Dai, Yinming; Wang, Qiuliang; Yan, Luguang

2014-03-15

Highlights: • Four different shape molds’ influence on NbTi cold-pressing joint are analyzed. • Deformation of filaments is the most uniform in the case of radial compression. • The square mold is the optimum one for decreasing joint resistance in practice. - Abstract: The cold-pressing welding methods are employed to fabricate joints between NbTi multi-filamentary conductors, and a series of joints are made with the molds of different shapes for nuclear magnetic resonance (NMR) magnet applications. The Abaqus–Explicit method was used to do a quasi-static analysis of the cold-pressing welding process. In the simulation, we analyzed four molds with different shapes: plate mold, cap mold, square mold, and radial compression. The simulation shows that the deformation of filaments is the most uniform in the case of radial compression and the square mold is the optimum one for decreasing joint resistance.

V-I transition and n-value of multifilamentary LTS and HTS wires and cables

International Nuclear Information System (INIS)

Ghosh, Arup K.

2004-01-01

For low T c multifilamentary conductors like NbTi and Nb 3 Sn, the V-I transition to the normal state is typically quantified by the parameter, n, defined by (ρ/ρ c )=(I/I c ) n . For NbTi, this parameterization has been very useful in the development of high J c wires, where the n-value is regarded as an index of the filament quality. In copper-matrix wires with undistorted filaments, the n-value at 5 T is ∼40-60, and drops monotonically with increasing field. However, n can vary significantly in conductors with higher resistivity matrices and those with a low copper fraction. Usually high n-values are associated with unstable resistive behavior and premature quenching. The n-value in NbTi Rutherford cables, when compared to that in the wires is useful in evaluating cabling degradation of the critical current due to compaction at the edges of the cable. In Nb 3 Sn wires, n-value has been a less useful tool, since often the resistive transition shows small voltages ∼ a few μV prior to quenching. However, in 'well behaved' wires, n is ∼30-40 at 12 T and also shows a monotonic behavior with field. Strain induced I c degradation in these wires is usually associated with lower n-values. For high T c multifilamentary wires and tapes, a similar power law often describes the resistive transition. At 4.2 K, Bi-2223 tapes as well as Bi-2212 wires exhibit n-values ∼15-20. In either case, n does not change appreciably with field. Rutherford cables of Bi-2212 wire show lower values of n than the virgin wire

Comparative Raman study of Weyl semimetals TaAs, NbAs, TaP and NbP

International Nuclear Information System (INIS)

Liu, H W; Richard, P; Zhao, L X; Chen, G-F; Ding, H

2016-01-01

We report a comparative polarized Raman study of Weyl semimetals TaAs, NbAs, TaP and NbP. The evolution of the phonon frequencies with the sample composition allows us to determine experimentally which atoms are mainly involved for each vibration mode. Our results confirm previous first-principles calculations indicating that the A 1 , B 1 (2), E(2) and E(3) modes involve mainly the As(P) atoms, the B 1 (1) mode is mainly related to Ta(Nb) atoms, and the E(1) mode involves both kinds of atoms. By comparing the energy of the different modes, we establish that the B 1 (1), B 1 (2), E(2) and E(3) become harder with increasing chemical pressure. This behaviour differs from our observation on the A 1 mode, which decreases in energy, in contrast to its behaviour under external pressure. (paper)

Metallurgy, fabrication, and superconducting properties of multifilamentary Nb3Al composites

International Nuclear Information System (INIS)

Hafstrom, J.W.

1976-01-01

The control of metallurgical structure during fabrication that will improve the superconducting properties of multifilamentary, aluminium-stabilized, Nb 3 Al composites is described. Composites are fabricated by placing niobium rods in an aluminum matrix, and then drawing to wire. Nb 3 Al is formed at temperatures exceeding 1800 0 C for about 5 s and ordered at 750 0 C for 48 h. A critical current, J/sub c/(H), in excess of 10 5 A/cm 2 (F/sub p/ approximately equal to 7 x 10 8 dynes/cm 3 ) at 7 T and a T/sub c/ to 18.2 K are obtained. Attempts to improve J/sub c/(H) by controlling the grain size in the Nb 3 Al diffused layer are discussed. Precipitates, arising from the addition of carbon during Nb 3 Al layer growth, do not appear to be effective as grain-boundary or flux pinners. When 1 percent Zr is added to the Nb, the growth of the Nb 3 Al layer is accelerated, T/sub c/ is lowered and J/sub c/(H) is not significantly improved. J/sub c/(H) rapidly decreases with an increase in Nb 3 Al or (Nb-Zr) 3 Al layer thickness, d. J/sub c/(H) is independent of d in composites with d greater than or approximately equal to 1.5 μm. In general, the Nb 3 Al grain size appears comparable to d for d less than or equal to 1 μm. Significant improvement of J/sub c/(H) for Nb 3 Al superconducting composites reacted at temperatures above 1800 0 C (to achieve T/sub c/ greater than 17 K) is achieved only by maintaining the layer thickness well below d approximately equal to 1.0 μm

Nb46, 5wt% Ti Eb-melting for AC and DC superconducting applications

International Nuclear Information System (INIS)

Bormio, C.; Ramos, M.J.; Pinatti, D.G.

1990-01-01

This paper reports on the superconductor alloy Nb46, 5wt % Ti which presents the best superconducting and mechanical properties for the systems Nb-Ti. The greatest difficulty in obtaining this alloy is related to the difference between the raw materials melting temperatures, which is about 700 degrees C. As a result the alloy homogeneity as well as Ti desired content, turn to be hard to control. The authors choose an electrode sandwich type, where Nb and Ti sheets are interposed. The electrode dimensions calculation is based on the Ti evaporation rate, energy balance and superficial tension of liquid titanium between Nb sheets. The ingots were electron beam melted. Herein, we present the following ingot results: Ti, intersticial and trace contents compared to international manufactures as well as its mechanical workability. This alloy will be used in NbTi wire production for AC and DC applications. The AC and DC wires are produced by coswaging and codrawing of NbTi bars and C u Ni-tubes for AC wires and Cu-tubes for DC wires. High area reductions of about 2 x 10 8 are reached without intermediate heat treatment, and they are essential since they are precursors of collective pinning centers, responsible for high critical current densities

Fabrication-process-induced variations of Nb/Al/AlOx/Nb Josephson junctions in superconductor integrated circuits

International Nuclear Information System (INIS)

Tolpygo, Sergey K; Amparo, Denis

2010-01-01

Currently, superconductor digital integrated circuits fabricated at HYPRES, Inc. can operate at clock frequencies approaching 40 GHz. The circuits present multilayered structures containing tens of thousands of Nb/Al/AlO x /Nb Josephson junctions (JJs) of various sizes interconnected by four Nb wiring layers, resistors, and other circuit elements. In order to be fully operational, the integrated circuits should be fabricated such that the critical currents of the JJs are within the tight design margins and the proper relationships between the critical currents of JJs of different sizes are preserved. We present experimental data and discuss mechanisms of process-induced variations of the critical current and energy gap of Nb/Al/AlO x /Nb JJs in integrated circuits. We demonstrate that the Josephson critical current may depend on the type and area of circuit elements connected to the junction, on the circuit pattern, and on the step in the fabrication process at which the connection is made. In particular, we discuss the influence of (a) the junction base electrode connection to the ground plane, (b) the junction counter electrode connection to the ground plane, and (c) the counter electrode connection to the Ti/Au or Ti/Pd/Au contact pads by Nb wiring. We show that the process-induced changes of the properties of Nb/Al/AlO x /Nb junctions are caused by migration of impurity atoms (hydrogen) between the different layers comprising the integrated circuits.

Superconducting materials for particle accelerator magnets

International Nuclear Information System (INIS)

Larbalestier, D.C.

1983-01-01

Present accelerator designs are clustered around a field of 5 Tesla with several future studies looking at the 8-to-10 Tesla range. There has also been some recent interest in low-field iron-dominated dipoles in which the superconductor will see a field of about 2 Tesla. The demands of this present range of interest can still be met, with the upper limit at about 10 Tesla, by the use of Nb-Ti (or Nb-Ti-Ta) or Nb 3 Sn. Both of these conductors are available in multifilamentary form from industrial sources and are suitable for accelerator magnets. The upper critical field and transition temperature of both types of composite cover the foreseeable range of demand for such magnets. There is no magical new composite on the horizon that is likely to replace Nb-Ti or Nb 3 Sn. One class of materials which has a potentially exciting prospect is that of the ternary molybdenum sulfides. These can have an upper critical field of greater than 50 T, which extends their superconductivity into field ranges unattainable with A15 compounds; the two drawbacks to such materials, however, are the amount of development needed to produce superconductors from them with useful current densities and the fact that it does not appear that they would offer any features not already possessed by Nb-Ti or Nb 3 Sn in the field range presently of interest to accelerator designers. Using this pragmatic approach, this paper addresses these and other superconducting composites in terms of their fabrication, their testing, the measurement aspects of their critical current densities, and other properties which are pertinent to their selection for particle accelerator magnet use

Voltage spikes in Nb3Sn and NbTi strands

Energy Technology Data Exchange (ETDEWEB)

Bordini, B.; Ambrosio, G.; Barzi, E.; Carcagno, R.; Feher, S.; Kashikhin, V.V.; Lamm, M.J.; Orris, D.; Tartaglia, M.; Tompkins, J.C.; Turrioni, D.; Yamada, R.; Zlobin,; /Fermilab

2005-09-01

As part of the High Field Magnet program at Fermilab several NbTi and Nb{sub 3}Sn strands were tested with particular emphasis on the study of voltage spikes and their relationship to superconductor instabilities. The voltage spikes were detected under various experimental conditions using voltage-current (V-I) and voltage-field (V-H) methods. Two types of spikes, designated ''magnetization'' and ''transport current'' spikes, have been identified. Their origin is most likely related to magnetization flux jump and transport current redistribution, respectively. Many of the signals observed appear to be a combination of these two types of spikes; the combination of these two instability mechanisms should play a dominant role in determining the minimum quench current.

Corrosion Characteristics of Ti-xTa Alloys with Ta contents

International Nuclear Information System (INIS)

Kim, H. J.; Choe, H. C.

2013-01-01

The purpose of this study was to investigate corrosion characteristics of Ti-xTa alloys with Ta contents. Ti-xTa alloys used as samples (x=30, 40%) were arc-melted under argon atmosphere of 99.9% purity. Ti-xTa alloys were homogenized for 12hr at 1000 .deg. C and then water quenched. The surface characteristics of Ti-xTa alloys were investigated using optical microscopy (OM) and X-ray diffractometer (XRD). The anodic corrosion behaviors of the specimens were examined through potentiodynamic, potentiostatic and galvanostatic test in 0.9 % NaCl solution at 36.5 ± 1 .deg. C. After corrosion test, the surface characteristics of Ti-xTa alloys were investigated using OM. The microstructure of Ti-Ta alloy showed the beta structure with Ta content. The corrosion resistance of Ti alloy was improved by increasing Ta content and the corrosion morphology of Ti-Ta alloy showed that the site attacked by chloride ion decreased from the active to passive region with Ta content. Potential of Ti-40Ta alloy increased as time increased, whereas, current density of Ti-40Ta alloy decreased as time increased compared to Ti-30 alloy

Characterization of nitride formation in NbTi-50% weight alloy by x-ray diffraction

International Nuclear Information System (INIS)

Teixeira, S.R.

1990-01-01

Titanium and niobium are so main metals for technology as structural materials, refractories and resistance alloys for corrosion. This interest is based in application of this metals and alloys in aerospacial industry, nuclear reactors, construction of superconductor magnets and in the production of superconductors wires. The NbTi (50% wt. Ti) alloy nitretation under nitrogen atmosphere (p + 760 mm) at 800 - 1000 C was studied by x-ray diffractometry. TEM and optical metallography. During the reaction the two phases (Ti sub(2) N - ε and TiN - δ) growed continuously, the (Ti sub(2) N, N sub(2)) reaction front growed faster than the (TiN,N sub(2)). A method for study the scale growing was proposed using x-ray diffractometry data. By using this method, the growth of TiN scale was analysed and the activation energy of 19 Kcal/mole was determinated using a linear timming law indicating a mechanism not controlled by diffusion through TiN layer. The present results suggest that the diffusion through the tight tunnels, rich in Nb, allow a fast transport of nitrogen through the TiN layer. (author)

Quench development in magnets made with multifilamentary NbTi cable

International Nuclear Information System (INIS)

Flora, R.H.; Kuchnir, M.; Tollestrup, A.V.

1976-01-01

An experimental study of the normal zone propagation and total resistance as a function of time is described. The normal zone propagation velocity in a single strand was measured as a function of both current and magnetic field with particular interest in the neighborhood of the short sample limit. The study proceeded from measurements in single multifilamentary strands to measurements in 23 strand cables under different cooling environments to final measurements in actual ramping dipole magnets made with this cable. Interpretation of the results led to the determination of safety limits for the Energy Doubler/Saver magnets and to safeguards implemented by an energy dumping circuit which effectively protects these magnets from self-destruction

A method to estimate the necessary twist pitch in multi-filamentary superconductors

International Nuclear Information System (INIS)

Lindau, S; Magnusson, N; Taxt, H

2014-01-01

Twisting of multi-filamentary superconductors is an important step in the development of wires with AC losses at an acceptable level for AC applications. The necessary twist pitch depends on wire architecture, critical current density, matrix material, and external factors such as temperature, frequency and applied magnetic field. The development of an AC optimized MgB 2 superconductor would be facilitated by a fast method to set the requirements for the twist pitch. A problem often encountered when comparing wires with different twist pitches is the degradation in critical current occurring at small twist pitches due to mechanical deformation. In this work we propose to use a non-twisted conductor to estimate the influence of twisting on the AC losses. A long superconductor is cut into smaller lengths, each simulating one third of the twist pitch, and the AC losses due to applied magnetic fields are compared between samples of different lengths. With this method, the effect of reducing the size of the loop of the coupling currents is studied without changing the superconducting parameters. AC loss measurement results are presented for a round titanium matrix MgB 2 wire with simulated twist pitches between 9 mm and 87 mm.

Aluminium stabilized Nb$-3$/Sn superconductors

International Nuclear Information System (INIS)

Thoener, M.; Krauth, H.; Rudolph, J.; Szulczyk, A.

1988-01-01

Composite superconductors made of reacted Nb 3 Sn stabilized with high purity Al were produced. Two methods were tested. The first involved soft soldering a Cu clad aluminum tape to the Nb 3 Sn conductor. In the second method the conductor, cable or monolith, was coextruded with the aluminum. Results obtained from using both methods indicated that mechanically reinforcing materials can be easily introduced into superconductors. Tests were conducted to determine magnetoresistance, electric contact resistance, yield strength, Young modulus, critical current, and other properties of the composites. Strengthening with Duratherm during coextrusion was also evaluated

The investigation of the effect of niobium artificial doping with titanium on Nb3Sn superconductors properties

International Nuclear Information System (INIS)

Nikulin, A.; Shikov, A.; Beliakov, N.; Semin, M.

1997-01-01

The effect on titanium doping of Nb filaments, and thus on the properties of bronze processed multifilamentary Nb 3 Sn wires and wires with internal tin sources with copper volume fraction up to 65 %, has been analysed. Either titanium rods or rods of the Nb-50Ti alloy, inserted in the axial area of each filament, were used as a source of titanium. The influence of doping on the quantity, composition, structure and superconducting properties of intermetallic compound Nb 3 Sn after heat treatments at 570-750 degrees C with duration up to 350 h was investigated by means of electrical measurements, optical metallography and methods of microanalysis and X-ray analysis. It was shown that the non-copper critical current density of the doped wires attained 600 and 270 A/mm 2 in 12.5 and 16 T respectively for bronze processed wires and 800 and 300 A/mm 2 for wires with internal tin source. Upper critical field calculated in accordance with Kramer's extrapolation was equal to 29-32 T

Program for development of high-field superconducting magnets for fusion research

International Nuclear Information System (INIS)

1975-01-01

Three superconducting magnet programs at LLL are outlined. The first program, the one considered in greatest detail, is a developmental program in which LLL will work closely with superconductor manufacturers to develop multifilamentary Nb 3 Sn superconductor suitable for use in large CTR magnets. The result of this program will be the fabrication of a rather large magnet (but one that is much smaller than future CTR magnets) and the determination of its performance limitations. In the second program, the developed multifilamentary Nb 3 Sn superconductor will be used to construct the magnets for the Fusion Engineering Research Facility (FERF) machine. In this program, the bulk of the effort will be in magnet design and winding. The third program chronologically overlaps the first two programs. This program includes the fabrication and testing of the superconducting magnets for the MX machine although, as explained in the Technical Plan, only the cost of the development work is included in this document. At the present time, Nb--Ti superconductor is being considered. Apart from some initial conductor design work, the major effort will be in magnet design and winding

Development of NbN Josephson junctions with Ta{sub x}N semi-metal barrier; application to RSFQ circuits; Etude et realisation de jonction Josephson en NbN a barriere semi-metallique en Ta{sub x}N; application aux circuits logiques RSFQ

Energy Technology Data Exchange (ETDEWEB)

Setzu, R

2007-11-15

This thesis research, brought to the development and optimization of SNS (Superconductor / Normal Metal / Superconductor) Josephson junctions with NbN electrodes and a high resistivity Ta{sub x}N barrier. We were able to point out Josephson oscillations for frequencies above 1 THz and operation temperatures up to 10 K, which constituted the original goal of the project. This property makes these junctions unique and well adapted for realizing ultra-fast RSFQ (Rapid Single Flux Quantum) logic circuits suitable for spatial telecommunications. We showed a good reproducibility of Ta{sub x}N film properties as a function of the sputtering parameters. The NbN/Ta{sub x}N/NbN tri-layers exhibit high critical temperature (16 K). The junctions showed a clear dependence of the R{sub n}I{sub c} product as a function of the partial nitrogen pressure inside the reactive plasma; the R{sub n}I{sub c} is the product between the junction critical current and its normal resistance, and indicates the upper limit Josephson frequency. We have also obtained some really high R{sub n}I{sub c} products, up to 3.74 mV at 4.2 K for critical current densities of about 15 kA/cm{sup 2}. Junctions show the expected Josephson behaviors, respectively Fraunhofer diffraction and Shapiro steps. up to 14 K. This allows expecting good circuit operations in a relaxed cryogenics environment (with respect to the niobium circuits limited at 4.2 K). The junctions appear to be self-shunted. The SNOP junctions J{sub c}-temperature dependence has been fitted by using the long SNS junction model in the dirty limit, which gives a normal metal coherence length of about 3.8 nm at 4.2 K. We have finally studied a multilayer fabrication process, including a common ground plane and bias resistors, suitable for RSFQ logic basic circuits. To conclude we have been able to show the performance superiority of NbN/Ta{sub x}N/NbN junctions over the actual niobium junctions, as well as their interest for realizing compact

Fine uniform filament superconductors

Science.gov (United States)

Riley, Jr., Gilbert N.; Li, Qi; Roberts, Peter R.; Antaya, Peter D.; Seuntjens, Jeffrey M.; Hancock, Steven; DeMoranville, Kenneth L.; Christopherson, Craig J.; Garrant, Jennifer H.; Craven, Christopher A.

2002-01-01

A multifilamentary superconductor composite having a high fill factor is formed from a plurality of stacked monofilament precursor elements, each of which includes a low density superconductor precursor monofilament. The precursor elements all have substantially the same dimensions and characteristics, and are stacked in a rectilinear configuration and consolidated to provide a multifilamentary precursor composite. The composite is thereafter thermomechanically processed to provide a superconductor composite in which each monofilament is less than about 50 microns thick.

Studies on Nb3Sn field coils for superconducting machine

International Nuclear Information System (INIS)

Fujino, H.; Nose, S.

1981-01-01

This paper describes experimental studies on several coils wound with multifilamentary (MF) Nb 3 Sn cables with reinforcing strip for superconducting rotating machine application. To use a Nb 3 Sn superconductor to field winding of a rotating machine, several coil performances of pre-reacted, bronze processed and stranded MF Nb 3 Sn cables were investigated, mainly in relation to stress effect. Bending strain up to 0.64% in strand and winding stress of 5 kg/mm 2 have resulted in nondegradation in coil performance. A pair of impregnated race-track coils designed for a 30 MVA synchronous condenser was energized successfully up to 80% of critical current without quench. 8 refs

Development and manufacturing of bronze-processed Ta-added Nb3Sn wires for the ITER

International Nuclear Information System (INIS)

Kikuchi, Kenichi; Seidou, Masahiro; Iwaki, Genzou; Sakai, Syuuji; Moriai, Hidezumi; Nishi, Masataka; Yoshida, Kiyoshi; Isono, Takaaki; Tsuji, Hiroshi.

1997-01-01

Development work to produce a high-performance Nb 3 Sn superconducting wire for the center solenoid coil of the ITER was carried out. The effects of concurrently adding Ti and Ta to bronze-processed Nb 3 Sn wires were examined. In addition, a high-Sn-concentration bronze matrix was applied. Then, the relation between hysteresis loss and filament diameter was examined. Moreover, the cause of wire breakage during processing was elucidated. As a result, a reliable manufacturing process for high-performance Nb 3 Sn superconducting wire was established. (author)

Development of Ti-12Mo-3Nb alloy for biomedical application

International Nuclear Information System (INIS)

Panaino, J.V.P.; Gabriel, S.B.; Mei, P.; Brum, M.V.; Nunes, C.A.

2010-01-01

The titanium alloys are quite satisfactory for biomedical applications due to their physical, mechanical and biological properties. Recent studies focuses on the development of beta type titanium alloys, composed of toxic elements (Nb, Mo, Ta ,...), because they have more advantages than alpha and alpha + beta (Ti- 6Al-4V) alloys such as lower modulus of elasticity, better plasticity and, moreover, the process variables can be controlled to produce selected results. This project focused on the development and characterization of Ti-12Mo-3Nb alloy in the condition 'as cast' and after thermomechanical treatment. The material was characterized in different conditions by X-ray diffraction, optical microscopy, microhardness measurements and elasticity modulus. The results showed that the forged Ti-12Mo-3Nb alloy showed the best combination of properties, being a promising candidate for use as implant. (author)

Design of Nb$_{3}$Sn magnetic devices to study the superconductor degradation under variable mechanical load

CERN Document Server

Regis, Federico

2009-01-01

The Large Hadron Collider (LHC) is a two-ring, superconducting synchrotron accelerator and collider installed in a 27 km long tunnel aiming at the discovery of the Higgs particle and the study of rare events with center mass collision energies of up to 14 TeV. The number of collisions per unit of area and time in a collider are evaluated trough the Luminosity function. Inside the LHC, superconducting magnets aligned with a precision of a few tenths of millimeters are used to bend and focus the particle trajectories. The LHC can be considered as the state of the art for superconducting magnets using the Nb-Ti superconductor technology. Therefore, a higher luminosity and beam energy can be achieved in the LHC only by using a more performing superconductor, such as the Nb$_{3}$Sn. This is considered as the most suitable superconductor to be used in high field magnets, allowing peak field of the order of 15 T. Nevertheless, the critical current jc variations in a Nb$_{3}$Sn has been found as strongly dependent on...

Enhancement of ductility in cubic Rh{sub 3}A{sub x}Ti{sub 1−x}(A = V,Nb,Ta)(x = 0, 0.125, 0.25, 0.75, 0.875, 1) aerospace materials–First principles DFT study

Energy Technology Data Exchange (ETDEWEB)

Manjula, M.; Sundareswari, M., E-mail: sundare65@gmail.com; Viswanathan, E.

2016-09-15

Structural, electronic, elastic and mechanical properties of cubic Rh{sub 3}A{sub x}Ti{sub 1−x} (where A = V, Nb, Ta and x = 0, 0.125, 0.25, 0.75, 0.875, 1) alloys are investigated by FP-LAPW method using the Density Functional Theory (DFT) within the generalized gradient approximation (GGA). The ground state properties of these compounds have been obtained by the optimization procedure as implemented in the wien2k code. The electronic and bonding patterns of the same are analysed. Using the calculated elastic constants, the Shear modulus, Young’s modulus, Poisson’s ratio, Pugh criteria, Cauchy’s pressure and Hardness values are derived. The ductility of these refractory alloys are analysed in terms of Cauchy’s pressure, Pugh criteria and Poisson’s ratio. The results are further assessed by using the charge density plots. From this study, we conclude that, among Rh{sub 3}A{sub x}Ti{sub 1−x} (A = V, Nb, Ta; x = 0, 0.125, 0.25, 0.75, 0.875, 1) alloy combinations, the Rh{sub 3}Nb{sub 0.75}Ti{sub 0.25} alloy is found to be more ductile and yet another combination namely Rh{sub 3}Nb{sub 0.875}Ti{sub 0.125} could serve as a preferred ductile material with a reasonable hardness. - Highlights: • The elastic and mechanical properties of Rh{sub 3}(V,Nb,Ta){sub x}Ti{sub 1−x} alloys are investigated. • Ductility of these materials are analysed using (C{sub 12}–C{sub 44}), G/B ratio and ν values. • The results are assessed by charge density plot. • Rh{sub 3}Nb{sub 0.75}Ti{sub 0.25} and Rh{sub 3}Nb{sub 0.875}Ti{sub 0.125} alloys are found to be more ductile.

Preparation, composition, and solid state investigations of TiN, ZrN, NbN, and compounds from the pseudobinary systems NbN-NbC, NbN-TiC, and NbN-TiN

International Nuclear Information System (INIS)

Christensen, A.N.; Fregerslev, S.

1977-01-01

Single crystals of the cubic phases TiN, ZrN, delta-NbN and of compounds from the pseudobinary systems NbN-NbC, NbN-TiC, and NbN-TiN were obtained by zone melting, zone annealing and annealing of the metal carbides in nitrogen gas of 2 MPa. Single crystals of the tetragonal phase gamma-NbN were obtained in a similar way by annealing of niobium. The nitrides are non-stochiometric. TiN was obtained in the composition range TiNsub(0.99) to TiNsub(0.50), ZrN in the range ZrNsub(1.00) to ZrNsub(0.63), and in niobium nitrides were obtained in the composition range NbNsub(0.90) to NbNsub(0.69). The compounds from the pseudobinary systems have up to 35% vacant sites in the nitrogen-carbon sublattice. TiN and ZrN have only vacant sites in the nitrogen sublattice. A correlation is found between the unit cell parameters for titanium nitride and zirconium nitride and the nitrogen-metal ratios. (orig.) [de

Effect of Cu4Ti compound formation on the characteristics of NbTi accelerator magnet wire

International Nuclear Information System (INIS)

Garber, M.; Suenaga, M.; Sampson, W.B.; Sabatini, R.L.

1985-01-01

High critical current density, J/sub c/ > 2500 A/mm 2 , and small filament diameter, d approx. 3 μm, are required in multifilamentary NbTi wire used for superconducting accelerator magnets. Wires obtained from various commercial sources had J/sub c/'s in the range 1000 to 2800 A/mm 2 amd d's in the range 1 to 23 μm. The filaments were examined by means of scanning electron microscopy in order to determine the reason for the variation in J/sub c/. It was found that the filaments in high J/sub c/ wires had clean smooth surfaces and uniform cross section along their lengths. Filaments in low J/sub c/ wires show formation of Cu 4 Ti compound particles on their surfaces and large variations in cross section. The lower critical current measured in these wires is believed to be largely due to this effect. The superconducting-normal state transition is relatively wide in these wires

In situ NiTi/Nb(Ti) composite

International Nuclear Information System (INIS)

Jiang, Daqiang; Cui, Lishan; Jiang, Jiang; Zheng, Yanjun

2013-01-01

Graphical abstract: - Highlights: • In situ NiTi/Nb(Ti) composites were fabricated. • The transformation temperature was affected by the mixing Ti:Ni atomic ratios. • The NiTi component became micron-scale lamella after forging and rolling. • The composite exhibited high strength and high damping capacity. - Abstract: This paper reports on the creation of a series of in situ NiTi/Nb(Ti) composites with controllable transformation temperatures based on the pseudo-binary hypereutectic transformation of NiTi–Nb system. The composite constituent morphology was controlled by forging and rolling. It is found that the thickness of the NiTi lamella in the composite reached micron level after the hot-forging and cold-rolling. The NiTi/Nb(Ti) composite exhibited high damping capacity as well as high yield strength

Transformation of Ti/sub 30/Nb/sub 30/Zr/sub 7/Ta superconducting alloy

Energy Technology Data Exchange (ETDEWEB)

Horiuchi, T; Monju, Y; Tatara, I; Nagi, N

1973-10-01

The effect of cold working on the rates of beta phase decomposition in the Ti/sub 30/Nb/sub 30/Zr/sub 7/Ta superconducting alloy was investigated. T.T.T. diagrams for the cold worked specimen were determined from the changes in electrical resistivity at liquid nitrogen temperature, Micro vickers hardness number measurement and the lattice constants determined by the x-ray powder method. Some results are as follows: (1) the alpha phase precipitation occurs by ageing at temperatures higher than 550/sup 0/C. At 550/sup 0/C, the beta phase decomposition into the alpha-beta minutes + beta seconds phase temperatures higher than 550/sup 0/C. At 550/sup 0/C, the beta phase decomposition into the alpha minutes + beta + betaseconds phase was found. (2) the rates of the alpha phase precipitation were accelerated by cold working. (3) the omega phase precipitation was found between 450 and 700/sup 0/C. 17 references.

Limitation of critical current density by intermetallic formation in fine filament Nb-Ti superconductors

International Nuclear Information System (INIS)

Larbalestier, D.C.; Chengren, L.; Starch, W.; Lee, P.J.

1985-01-01

Two experiments have been performed to investigate the role that the intermetallic reaction between the copper matrix and the Nb-Ti filaments plays in limiting the critical current density (J/sub c/) of Nb 45.6 wt% Ti composites. The first experiment involved composites which were industrially extruded. It was found that as the number of heat treatments increased, the J/sub c/ declined, the resistive transition broadened and the filaments sausaged. The filament sausaging was initiated by intermetallic particles at the filament matrix interface. A series of many heat treatment procedures were then applied to composites fabricated in the authors own laboratories without extrusion. Very high J/sub c/ values were obtained at filament sizes of 20 μm. When the same heat treatment procedures were applied to 4 - 5 μm conductors, extensive sausaging and degraded J/sub c/ values resulted. This degradation was also found to be due to the formation of Cu-Nb-Ti intermetallic compounds. It is concluded that a reliable filament diffusion barrier technology is necessary to permit full flexibility in the heat treatment of 2 - 5 μ filament Nb-Ti composites

Limitation of critical current density by intermetallic formation in fine filament Nb-Ti superconductors

International Nuclear Information System (INIS)

Larbalestier, D.C.; Chengren, Li; Lee, P.J.; Starch, W.

1985-01-01

Two experiments have been performed to investigate the role that the intermetallic reaction between the copper matrix and the Nb-Ti filaments plays in limiting the critical current density (J /SUB c/ ) of Nb 46.5 wt% Ti composites. The first experiment involved composites which were industrially extruded. It was found that as the number of heat treatments increased, the J /SUB c/ declined, the resistive transition broadened and the filaments sausaged. The filament sausaging was initiated by intermetallic particles at the filament matrix interface. A series of many heat treatment procedures were then applied to composites fabricated in our own laboratories without extrusion. Very high J /SUB c/ values were obtained at filament sizes of 20 μm. When the same heat treatment procedures were applied to 4 - 5 μm conductors, extensive sausaging and degraded J /SUB c/ values resulted. This degradation was also found to be due to the formation of Cu-Nb-Ti intermetallic compounds. It is concluded that a reliable filament diffusion barrier technology is necessary to permit full flexibility in the heat treatment of 2 - 5 μm filament Nb-Ti composites

Electric field gradient at the Nb3M(M = Al, In, Si, Ge, Sn) and T3Al (T = Ti, Zr, Hf, V, Nb, Ta) alloys by perturbed angular correlation method

International Nuclear Information System (INIS)

Junqueira, Astrogildo de Carvalho

1999-01-01

The electric field gradient (efg) at the Nb site in the intermetallic compounds Nb 3 M (M = Al, Si, Ge, Sn) and at the T site in the intermetallic compounds T 3 Al (T = Ti, Zr, Hf, V, Nb, Ta) was measured by Perturbed Angular Correlation (PAC) method using the well known gamma-gamma cascade of 133-482 keV in 181 Ta from the β - decay of 181 Hf. The compounds were prepared by arc melting the constituent elements under argon atmosphere along with radioactive 181 Hf substituting approximately 0.1 atomic percent of Nb and T elements. The PAC measurements were carried out at 295 K for all compounds and the efg was obtained for each alloy. The results for the efg in the T 3 Al compounds showed a strong correlation with the number of conduction electrons, while for the Nbs M compounds the efg behavior is influenced mainly by the p electrons of the M elements. The so-called universal correlation between the electronic and lattice contribution for the efg in metals was not verified in this work for all studied compounds. Measurements of the quadrupole frequency in the range of 100 to 1210 K for the Nb 3 Al compound showed a linear behaviour with the temperature. Superconducting properties of this alloys may probably be related with this observed behaviour. The efg results are compared to those reported for other binary alloys and discussed with the help of ab-initio methods. (author)

Influence of Heat Treatment and UV Irradiation on the Wettability of Ti35Nb10Ta Nanotubes

Directory of Open Access Journals (Sweden)

Joan Lario

2018-01-01

Full Text Available The implant osseointegration rate depends on the surface’s topography and chemical composition. There is a growing interest in the anodic oxidation process to obtain an oxide layer with a nanotube morphology on beta titanium alloys. This surface treatment presents large surface area, nanoscale rugosity and electrochemical properties that may increase the biocompatibility and osseointegration rate in titanium implants. In this work, an anodic oxidation process was used to modify the surface on the Ti35Nb10Ta alloy to obtain a titanium nanotubes topography. The work focused on analyzing the influence of some variables (voltage, heat treatment and ultraviolet irradiation on the wettability performance of a titanium alloy. The morphology of the nanotubes surfaces was studied by Field Emission Scanning Electron Microscopy (FESEM, and surface composition was analyzed by Energy Dispersive Spectroscopy (EDS. The measurement of contact angle for the TiO2 nanotube surfaces was measured by a video contact angle system. The surface with the non photoinduced nanotubes presented the largest contact angles. The post-heat treatment lowered the F/Ti ratio in the nanotubes and decreased the contact angle. Ultraviolet (UV irradiation of the TiO2 nanotubes decrease the water contact angle.

Influence of oxygen on omega phase stability in the Ti-29Nb-13Ta-4.6Zr alloy

International Nuclear Information System (INIS)

Niinomi, Mitsuo; Nakai, Masaaki; Hendrickson, Mandana; Nandwana, Peeyush; Alam, Talukder; Choudhuri, Deep; Banerjee, Rajarshi

2016-01-01

The effect of oxygen on stability of isothermal omega precipitates in Ti-29Nb-13Ta-4.6Zr was examined using X-ray powder diffraction, transmission electron microscopy, and atom probe tomography. Two alloys with 0.1 and 0.4 mass% oxygen were subjected to single step, and two-step annealing heat-treatments to respectively promote omega and alpha formation. After second step annealing, large volume fraction of omega precipitates was retained in 0.4 mass% O alloy while mainly alpha phase was observed in TNTZ-0.1O. The enhanced stability of omega in the higher oxygen containing TNTZ alloys questions the conventionally accepted understanding that oxygen destabilizes the omega phase in titanium alloys.

Superconductivity and specific heat measurements in V--Nb--Ta ternary alloys

International Nuclear Information System (INIS)

Wang, R.Y.P.

1977-01-01

The correlation between the superconducting transition temperature T/sub c/ with electronic specific heat coefficient γ and Debye temperature theta/sub D/ in some isoelectronic ternary V--Nb--Ta alloys is investigated. It has been known that the variation of theta/sub D/ with concentration in both V--Nb and V--Ta systems is clearly of the same curvature as that of T/sub c/ and γ. In Ta--Nb alloys, however, over most of the concentration range theta/sub D/ seems to have a slight negative curvature while T/sub c/ and γ curve upwards. (But beyond approx. 80 at. % Nb theta/sub D/ rises rapidly to the pure Nb value.) By choosing alloys along a line connecting Ta and V 25 --Nb 75 which is close to the Nb--Ta side of the Gibb's triangle the extent to which the Nb--Ta type of behavior persists in this ternary system can be estimated. A model proposed by Miedema that takes into account the variation of properties caused by possible charge transfer among constituent atoms in an alloy has been found to apply almost quantitatively for nearly all binary alloy systems whose experimental data are available, including those for which Hopfield's method fails. A previous test of the extension of Miedema's empirical model into ternary alloys shows qualitatively correct behavior for intra-row Zr/sub x/Nb/sub 1-2x/Mo/sub x/ alloys. The good agreement between the predicted values of γ and T/sub c/ and the experimental values in the inter-row ternary V--Nb--Ta system studied here gives another and better test of the application of Miedema's model

Improvement of stability of Nb₃ Sn superconductors by introducing high specific heat substances

Energy Technology Data Exchange (ETDEWEB)

Xu, X. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Li, P. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Zlobin, A. V. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Peng, X. [Unlisted, US, OH

2018-01-24

High-J_c Nb₃Sn conductors have low stability against perturbations, which accounts for the slow training rates of high-field Nb₃Sn magnets. While it is known that adding substances with high specific heat (C) into Nb3Sn wires can increase their overall specific heat and thus improve their stability, there has not been a practical method that is compatible with the fabrication of long-length conductors. In this work, we put forward a scheme to introduce such substances to distributed-barrier Nb₃Sn wires, which adds minimum difficulty to the wire manufacturing process. Multifilamentary wires using a mixture of Cu and high-C Gd₂O₃ powders have been successfully fabricated along this line. Measurements showed that addition of Gd₂O₃ had no negative effects on residual resitivity ratio or non-Cu J_c, and that flux jumps were remarkably reduced, and minimum quench energy values at 4.2 K, 14 T were increased by a factor of three, indicating that stability was significantly improved. We also discussed the influences of the positioning of high-C substances and their thermal diffusivity on their effectiveness in reducing the superconductor temperature rise against perturbations. Based on these results, we proposed an optimized conductor architecture to maximize the effectiveness of this approach.

Experimental investigation of phase equilibria in the Nb-Si-Ta ternary system

Energy Technology Data Exchange (ETDEWEB)

Li, Jian; Wang, Cuiping; Yao, Jun; Yang, Shuiyuan; Zhan Shi; Liu, Xingjun [Xiamen Univ. (China). Dept. of Materials Science and Engineering; Xiamen Univ. (China). Fujian Provincial Key Laboratory of Materials Genome; Kang, Yongwang [Beijing Institute of Aeronautical Materials (China). Science and Technology on Advanced High Temperature Structural Materials Lab.

2016-12-15

The phase equilibria in the Nb-Si-Ta ternary system at 1 373 K, 1 473 K and 1 573 K were investigated by means of back-scattered electron imaging, electron probe microanalysis and X-ray diffraction. The isothermal sections at 1 373 K, 1 473 K and 1 573 K consist of two three-phase regions and seven two-phase regions, without any ternary compounds. The compounds of NbSi{sub 2} and TaSi{sub 2}, αNb{sub 5}Si{sub 3} and αTa{sub 5}Si{sub 3} form continuous solid solutions, respectively. The solubilities of Nb in Ta{sub 3}Si and Ta{sub 2}Si phases are extremely large, whereas the solubility of Si in the β(Nb, Ta) phase is relatively small.

Performance Limits and IR Design Challenges of a Possible LHC Luminosity Upgrade Based on Nb-Ti SC Magnet Technology

CERN Document Server

Brüning, Oliver Sim; Ostojic, R; Rossi, L; Ruggiero, F; Scandale, Walter; Taylor, T

2004-01-01

We investigate the maximum LHC performance for a standard IR design based on classical NbTi insertion magnets. We include in our analysis a ternary Nb-based ductile allow such as NbTi(Ta), a less developed but relatively cheap superconducting material which may allow to gain about 1 T in the peak field in the coils, and discuss the corresponding luminosity reach for a possible LHC upgrade compared to that based on Nb$_{3}$Sn magnets.

Fabrication and characterization of fine filaments of NbTi in a copper matrix

International Nuclear Information System (INIS)

Hemachalam, K.; King, C.G.; Scanlan, R.M.; Zeitlin, B.A.

1986-01-01

Practical multifilamentary Nb-46.5 Wt. % Ti/Cu composites have been made by a double extrusion process. The composites contain up to 6000 filaments with a diameter of 2 to 6 μm at the final wire size. Through careful attention to the billet design and thermo-mechanical processing, the formation of intermetallics (Cu-Ti-Nb) is virtually halted. The intermetallic precipitates, when allowed to form at the filament surface, interfere with the uniform reduction and give rise to poor filament quality; including filament breaks and reduction in critical current density, Jc. The integrity of the present fine filaments is studied with SEM and compared with that of conventionally processed material. The Jc, as a function of the filament size, is investigated over a transverse magnetic field of up to 8 Tesla. The value of 'n' in /rho/=kI /SUP n/ is measured and the results are compared to those obtained for similar M.F. wires currently under study at other institutions. It is hoped that the fine filamentary wire produced by the double extrusion process will greatly reduce the magnetization which is responsible for field distortions in the High Energy Physics program applications

Mechanical properties of high-current multifilamentary Nb3Sn conductors

International Nuclear Information System (INIS)

Scanlan, R.M.; Hoard, R.W.; Cornish, D.N.; Zbasnik, J.P.

1980-01-01

Nb 3 Sn is a strain-sensitive superconductor which exhibits large changes in properties for strains of less than 1 percent. The critical current density at 12 T undergoes a reversible degradation of a factor of two for compressive strains of about 1 percent and undergoes an irreversible degradation for tensile strains on the Nb 3 Sn greater than 0.2 percent. Consequently, the successful application of Nb 3 Sn in large high-field magnets requires a complete understanding of the mechanical properties of the conductor. One conductor which is being used for many applications consists of filaments of Nb 3 Sn in a bronze matrix, and much progress has been made in understanding the mechanical behavior of this composite. The Nb 3 Sn filaments are placed in compression due to the differential thermal contraction between Nb 3 Sn and bronze which occurs when the composite is cooled from the Nb 3 Sn formation temperature (typically 700 0 C) to the 4.2 0 K operating temperature. The general behavior of the critical current when this conductor is subjected to a tensile stress is an increase to a maximum when the compressive strain on the Nb 3 Sn is relieved, followed by a decrease as the Nb 3 Sn filemants are placed in tension. The degree of precompression is controlled largely by the ratio of bronze to Nb 3 Sn in the conductor

Tritium diffusion in V, Nb and Ta

International Nuclear Information System (INIS)

Qi, Z.; Voelkl, J.; Laesser, R.; Wenzl, H.

1983-01-01

Gorsky-effect measurements of the diffusion coefficient of tritium (T) in V, Nb and Ta are reported. The measurements were performed at small T concentrations (less than about 1.4 at%), and in the temperature range from -140 0 C to 100 0 C. Comparison with results obtained for H and D shows an increase of the activation energy with increasing isotopic mass. For Nb and Ta, the pre-exponential factors are identical for all the isotopes, whereas for V this factor is appreciably larger for T than for H and D. The reduction of the relaxation strength in the presence of precipitation allows a rough determination of the solubility limit, which is found to be isotope independent for Nb and Ta. In V, the solubility limit for T is shifted slightly to lower temperatures. The H, D or T induced lattice expansion calculated from the relaxation strength shows no dependence on isotopic mass. (author)

Supporting data for senary refractory high-entropy alloy CrxMoNbTaVW

Directory of Open Access Journals (Sweden)

B. Zhang

2015-12-01

Full Text Available This data article is related to the research paper entitled “senary refractory high-entropy alloy CrxMoNbTaVW [1]”. In this data article, the pseudo-binary Cr-MoNbTaVW phase diagram is presented to show the impact of Cr content to the senary Cr-MoNbTaVW alloy system; the sub-lattice site fractions are presented to show the disordered property of the Cr-MoNbTaVW BCC structures; the equilibrium and Scheil solidification results with the actual sample elemental compositions are presented to show the thermodynamic information of the melted/solidified CrxMoNbTaVW samples; and the raw EDS scan data of the arc-melted CrxMoNbTaVW samples are also provided.

Density of thermal vacancies in γ-Ti-Al-M, M = Si, Cr, Nb, Mo, Ta or W

International Nuclear Information System (INIS)

Woodward, C.; Kajihara, S.

1999-01-01

Modifications to alloy chemistry are often used to tailor the intrinsic flow behavior of structural materials. Models of creep in intermetallic alloys must account for the influence of chemistry on the available intrinsic creep mechanisms. As in simple metals the presence of vacancies strongly influences bulk diffusion processes in these materials. Limiting the density of constitutional and thermal vacancies by alloying may produce materials with enhanced creep properties. The energy of intrinsic and substitutional point defects in L1 0 TiAl is calculated within a first principles, local density functional theory framework. Relaxed structures and energies for vacancies, antisites and solid solutions are calculated using a plane-wave-pseudopotential method. Calculated defect energies are used within a canonical ensemble formalism to estimate the point defect densities as a function of temperature and composition. The density of vacancies is found to be sensitive to the underlying stoichiometry of TiAl. The dependence of the vacancy concentration for solid solutions of Si, Cr, Nb, Mo, Ta and W is also predicted

Effect of transverse compression on I/sub c/ of Nb3Sn multifilamentary wire

International Nuclear Information System (INIS)

Specking, W.; Goldacker, W.; Fluekiger, R.

1988-01-01

The effect of transverse compressive stress on critical current in bronze processed Nb 3 Sn multifilamentary wires was measured at 13.5 T. For the same wire the critical current was more sensitive to this stress than to axial stress. An increase in this stress first caused a slight enhancement of the critical current followed by a drastic decrease of 50 percent at a stress equal to 100 MPa. X-ray diffraction under transverse compression revealed a decrease in the spacing between the lattice planes parallel to the wire axis. This provided a physical basis for the initial enhancement of the critical current under transverse compressive stress

Effect of bronze on the compression of Nb3Sn in multifilamentary conductors

International Nuclear Information System (INIS)

Rupp, G.

1978-01-01

Nb 3 Sn in multifilamentary conductors is subject to compressive strain as a result of the relatively small thermal contraction of the filaments as compared to bronze. The critical current Isub(c) is consequently degraded. The critical current increases, when an external tensile stress is applied, and passes through a maximum. The ratio of the maximum critical current to the initial critical current increases with the flux density and reaches a value of two at a flux density of 16 T for technical conductors. The strain epsilonsub(m), at which Isub(c) maximum is reached, lies between 0.4% and 0.7% for the conductors investigated and depends on the material parameters. For a constant ratio of bronze to filament cross section this strain epsilonsub(m) is reduced as the Nb 3 Sn layer thickness is increased and can be determined approximately by a graphical method from the stress-strain diagram. Epsilonsub(m) is to a large extent dependent on the metallurgical properties of bronze, which vary to a considerable extent depending upon the heat treatment. (author)

Joining NbTi superconductors by ultrasonic welding

International Nuclear Information System (INIS)

Hafstrom, J.W.; Killpatrick, D.H.; Niemann, R.C.; Purcell, J.R.; Thresh, H.R.

1976-01-01

An important consideration in the design and construction of large, high-field, superconducting magnets is the capability to fabricate reliable, high-strength, low-resistance joints. A process for joining NbTi, copper stabilized, superconducting composites by ultrasonic welding is described. This process yields a joint strength comparable to that of the superconducting composite and a resistivity significantly lower than achieved by conventional soft soldering. The superconducting properties of the composite are not affected by the joining process. Scarfing the joint to maintain a constant conductor cross section does not degrade its electrical or mechanical properties. The application of the ultrasonic joining process, including process control, scarfing, and NDT procedures, in the construction of the superconducting magnet (U.S. SCMS) for the joint U. S. -- Soviet MHD program is described

GaN/NbN epitaxial semiconductor/superconductor heterostructures

Science.gov (United States)

Yan, Rusen; Khalsa, Guru; Vishwanath, Suresh; Han, Yimo; Wright, John; Rouvimov, Sergei; Katzer, D. Scott; Nepal, Neeraj; Downey, Brian P.; Muller, David A.; Xing, Huili G.; Meyer, David J.; Jena, Debdeep

2018-03-01

Epitaxy is a process by which a thin layer of one crystal is deposited in an ordered fashion onto a substrate crystal. The direct epitaxial growth of semiconductor heterostructures on top of crystalline superconductors has proved challenging. Here, however, we report the successful use of molecular beam epitaxy to grow and integrate niobium nitride (NbN)-based superconductors with the wide-bandgap family of semiconductors—silicon carbide, gallium nitride (GaN) and aluminium gallium nitride (AlGaN). We apply molecular beam epitaxy to grow an AlGaN/GaN quantum-well heterostructure directly on top of an ultrathin crystalline NbN superconductor. The resulting high-mobility, two-dimensional electron gas in the semiconductor exhibits quantum oscillations, and thus enables a semiconductor transistor—an electronic gain element—to be grown and fabricated directly on a crystalline superconductor. Using the epitaxial superconductor as the source load of the transistor, we observe in the transistor output characteristics a negative differential resistance—a feature often used in amplifiers and oscillators. Our demonstration of the direct epitaxial growth of high-quality semiconductor heterostructures and devices on crystalline nitride superconductors opens up the possibility of combining the macroscopic quantum effects of superconductors with the electronic, photonic and piezoelectric properties of the group III/nitride semiconductor family.

Ferromagnetic artificial pinning centers in multifilamentary superconducting wires

International Nuclear Information System (INIS)

Wang, J.Q.; Rizzo, N.D.; Prober, D.E.

1997-01-01

The authors fabricated multifilamentary NbTi wires with ferromagnetic (FM) artificial pinning centers (APCs) to enhance the critical current density (J c ) in magnetic fields. They used a bundle and draw technique to process the APC wires with either Ni or Fe as the pinning centers. Both wires produced higher J c in the high field range (5-9 T) than previous non-magnetic APC wires similarly processed, even though the authors have not yet optimized pin percentage. Using a magnetometer they found that the pins remained ferromagnetic for the wires with maximum J c . However, they did observe a substantial loss of FM material for the wires where the pin diameter approached 3 nm. Thus, they expect further enhancement of J c with better pin quality

Strand critical current degradation in $Nb_{3}$ Sn Rutherford cables

CERN Document Server

Barzi, E; Higley, H C; Scanlan, R M; Yamada, R; Zlobin, A V

2001-01-01

Fermilab is developing 11 Tesla superconducting accelerator magnets based on Nb/sub 3/Sn superconductor. Multifilamentary Nb/sub 3/Sn strands produced using the modified jelly roll, internal tin, and powder-in-tube technologies were used for the development and test of the prototype cable. To optimize the cable geometry with respect to the critical current, short samples of Rutherford cable with packing factors in the 85 to 95% range were fabricated and studied. In this paper, the results of measurements of critical current, n-value and RRR made on the round virgin strands and on the strands extracted from the cable samples are presented. (5 refs).

Magnetization and critical currents of NbTi wires with fine filaments

International Nuclear Information System (INIS)

Ghosh, A.K.; Sampson, W.B.

1985-01-01

In high energy accelerators such as the SSC, the magnetization of the superconductor is an important component in determining the harmonic fields at injection (approx.0.3T). In an effort to reduce these residual fields, interest has focused on NbTi conductors with fine filaments which are expected to have a reduced magnetization as dictated by the critical state model. With this in view, the magnetization and critical currents were measured at 4.3K for a set of NbTi wires with filament diameters, d, ranging from 1.0 to 5.0 microns. The data show that, although the magnetization scales linearly with d, it does not do so with the product J/sub c/d for d less than 3 μm. However, at these d values, the critical transport current density, J/sub c/ of NbTi was observed to decrease rapidly as a function of d. The origin of this J/sub c/ degradation and its effect on the scaling of magnetization within the framework of the critical state model is explored. We also examine the question of the observed asymmetry of the hysteretic magnetization

Characterization of a High Strength, Refractory High Entropy Alloy, AlMo0.5NbTa0.5TiZr

Science.gov (United States)

Jensen, Jacob

High entropy alloys (HEAs) are a relatively new class of materials that have garnered significant interest over the last decade due to their intriguing balance of properties including high strength, toughness, and corrosion resistance. In contrast to conventional alloy systems, HEAs are based on four or more principal elements with near equimolar concentrations and tend to have simple microstructures due to the preferential formation of solid solution phases. HEAs appear to offer new pathways to lightweighting in structural applications, new alloys for elevated temperature components, and new magnetic materials, but more thorough characterization studies are needed to assess the viability of the recently developed multicomponent materials. One such HEA, AlMo0.5NbTa0.5TiZr, was selected to be the basis for this characterization study in part due to its strength at elevated temperatures (sigma0.2 = 1600 MPa at T = 800 °C) and low density compared with commercially available Ni-based superalloys. The refractory element containing HEA composition was developed in order to balance the high temperature strength of the refractory elements with the desirable properties achieved by the high entropy alloying design approach for potential use in aerospace thermal protection and structural applications. Ingots of AlMo0.5NbTa0.5TiZr were cast by vacuum arc melting followed by hot isostatic pressing (HIP) and homogenization at 1400 °C for 24 hrs with a furnace cool of 10 °C/min. The resulting microstructure was characterized at multiple length scales using x-ray diffraction (XRD), scanning transmission electron microscopy (SEM), conventional and scanning transmission electron microscopy (TEM and STEM), and x-ray energy dispersive spectroscopy (XEDS). The microstructure was found to consist of a periodic, coherent two phase mixture, where a disordered bcc phase is aligned orthogonally in an ordered B2 phase. Through microstructural evolution heat treatment studies, the

Reduction of coupling in fine filamentary Cu-NbTi composites by the addition of manganese to the matrix

International Nuclear Information System (INIS)

Kreilick, T.S.; Gregory, E.; Wong, J.; Scanlan, R.M.; Ghosh, A.K.; Sampson, W.B.; Collings, E.W.

1988-01-01

Proximity coupling has been observed in materials containing 4164 filaments in a pure copper matrix designed and fabricated by Supercon Inc. for SSC dipoles. The effect of manganese additions to the copper matrix in reducing this coupling was assessed in this paper. Two multifilamentary NbTi billets were fabricated for SSC inner cable applications. Each composite contains roughly 11,000 filaments embedded in pure copper and copper manganese matrices. Critical current, magnetization, stability, susceptibility and mechanical analyses of these materials indicated no adverse effects from 0.5 wt.% manganese additions to the copper. Results on coupling reduction are evaluated

Solid solution cermet: (Ti,Nb)(CN)-Ni cermet.

Science.gov (United States)

Kwon, Hanjung; Jung, Sun-A

2014-11-01

Solid solution powders without W, (Ti,Nb)(CN) powders with a B1 structure (NaCl like), were synthesized by high energy milling and carbothermal reduction in nitrogen. The range of molar ratios of Ti/Nb for forming complete (Ti,Nb)(CN) phase was broader than that of Ti/W for the (Ti,W)(CN) phase because carbide or carbonitride of Nb had a B1 crystal structure identical to Ti(CN) while WC had a hexagonal crystal structure. The results revealed that the hardness of (Ti,Nb)(CN)-Ni cermets was higher than that of (Ti,W)(CN)-Ni cermets. The lower density of the (Ti,Nb)(CN) powder contributed to the higher hardness compared to (Ti,W)(CN) because the volumetric ratio of (Ti,Nb)(CN) in the (Ti,Nb)(CN)-Ni cermets was higher than that of (Ti,Nb)(CN) in the (Ti,W)(CN)-Ni cermets at the same weight ratio of Ni. Additionally, it was assumed that intrinsic the properties of (Ti,Nb)(CN) could also be the cause for the high hardness of the (Ti,Nb)(CN)-Ni cermets.

High Nb, Ta, and Al creep- and oxidation-resistant austenitic stainless steel

Science.gov (United States)

Brady, Michael P [Oak Ridge, TN; Santella, Michael L [Knoxville, TN; Yamamoto, Yukinori [Oak Ridge, TN; Liu, Chain-tsuan [Oak Ridge, TN

2010-07-13

An austenitic stainless steel HTUPS alloy includes, in weight percent: 15 to 30 Ni; 10 to 15 Cr; 2 to 5 Al; 0.6 to 5 total of at least one of Nb and Ta; no more than 0.3 of combined Ti+V; up to 3 Mo; up to 3 Co; up to 1 W; up to 0.5 Cu; up to 4 Mn; up to 1 Si; 0.05 to 0.15 C; up to 0.15 B; up to 0.05 P; up to 1 total of at least one of Y, La, Ce, Hf, and Zr; less than 0.05 N; and base Fe, wherein the weight percent Fe is greater than the weight percent Ni wherein said alloy forms an external continuous scale comprising alumina, nanometer scale sized particles distributed throughout the microstructure, said particles comprising at least one composition selected from the group consisting of NbC and TaC, and a stable essentially single phase fcc austenitic matrix microstructure, said austenitic matrix being essentially delta-ferrite-free and essentially BCC-phase-free.

XYO{sub 3} (X = K, Na; Y = Nb, Ta) based superlattices for photocatalysis

Energy Technology Data Exchange (ETDEWEB)

Wang, Guang-Zhao; Chen, Xiao-Rui; Yuan, Hong-Kuan; Kuang, An-Long [School of Physical Science and Technology, Southwest University, Chongqing 400715 (China); Chen, Hong [School of Physical Science and Technology, Southwest University, Chongqing 400715 (China); Key Laboratory of Luminescent and Real-Time Analytical Chemistry, Ministry of Education, College of Chemistry and Chemical Engineering, Southwest University, Chongqing 400715 (China)

2017-05-15

The photocatalytic activities of XYO{sub 3} (X = K, Na; Y = Ta, Nb) and XYO{sub 3}/X1Y1O{sub 3} (X, X1 = K, Na; Y, Y1 = Ta, Nb) systems are investigated by using hybrid density functional. All the XYO{sub 3} and XYO{sub 3}/X1Y1O{sub 3} systems are indirect band gap semiconductors, and the band gap of KNbO{sub 3}/KTaO{sub 3} is smaller than those of KNbO{sub 3} and KTaO{sub 3}, while the band gaps of KNbO{sub 3}/NaNbO{sub 3}, KNbO{sub 3}/NaTaO{sub 3}, KTaO{sub 3}/NaNbO{sub 3}, KTaO{sub 3}/NaTaO{sub 3}, and NaNbO{sub 3}/NaTaO{sub 3} are respectively between the band gaps of these two crystals which make up these superlattices. The electronic structure of KNbO{sub 3}/NaTaO{sub 3} is the same as that of KTaO{sub 3}/NaNbO{sub 3} since both have the same component and similar crystal structure. The band edges of all the considered superlattices are thermodynamically allowed for the water reduction and oxidation processes, and therefore, they could be used for photocatalytic water splitting. Band structures for (i) KNbO{sub 3}/KTaO{sub 3}, (ii) KNbO{sub 3}/NaNbO{sub 3}, (iii) KNbO{sub 3}/NaTaO{sub 3}, (iv) KTaO{sub 3}/NaNbO{sub 3}, (v) KTaO{sub 3}/NaTaO{sub 3}, and (vi) NaNbO{sub 3}/NaTaO{sub 3} superlattices. The horizontal dashed lines represent the Fermi levels. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Effect of Cold Deformation and Annealing on the Microstructure and Tensile Properties of a HfNbTaTiZr Refractory High Entropy Alloy

Science.gov (United States)

Senkov, O. N.; Pilchak, A. L.; Semiatin, S. L.

2018-05-01

The microstructure and tensile properties of HfNbTaTiZr after cold working and annealing were investigated. Cold work was introduced by axial compression followed by rolling resulting in a total thickness reduction of 89 pct without any evidence of cracking. The cold-worked material retained a single-phase microstructure and had a room temperature tensile yield stress σ 0.2 = 1438 MPa, peak true stress σ p = 1495 MPa, and true fracture strain ɛ f = 5 pct. Annealing at 800 °C for up to 256 hours resulted in the precipitation of Nb and Ta rich particles with a BCC crystal structure inside a Hf-and-Zr-enriched BCC matrix. The second phase particles nucleated heterogeneously inside deformation bands and slip lines and coarsened during annealing. Analysis of the coarsening behavior suggested that kinetics were controlled by the diffusion of Nb and Ta. In the two-phase material, σ 0.2 and σ p decreased from 1159 to 1071 MPa and from 1174 to 1074 MPa, respectively, with an increase in particle diameter from 0.18 to 0.72 μm, while ɛ f remained between 5 and 8 pct. Full recrystallization and normal grain growth, with the activation energy of 238 kJ/mol and activation volume of 5.3 to 9.6 m3/mol, occurred during annealing above 1000 °C. After heat treatment at this temperature, the alloy was characterized by a single-phase BCC structure with σ 0.2 = 1110 to 1115 MPa, σ p = 1160 to 1195 MPa, and ɛ f = 12 to 19 pct with the maximum values attained after annealing for 1 hour.

Biological Properties of Ti-Nb-Zr-O Nanostructures Grown on Ti35Nb5Zr Alloy

Directory of Open Access Journals (Sweden)

Zhaohui Li

2012-01-01

Full Text Available Surface modification of low modulus implant alloys with oxide nanostructures is one of the important ways to achieve favorable biological behaviors. In the present work, amorphous Ti-Nb-Zr-O nanostructures were grown on a peak-aged Ti35Nb5Zr alloy through anodization. Biological properties of the Ti-Nb-Zr-O nanostructures were investigated through in vitro bioactivity testings, stem cell interactions, and drug release experiments. The Ti-Nb-Zr-O nanostructures demonstrated a good capability of inducing apatite formation after immersion in simulated body fluids (SBFs. Drug delivery experiment based on gentamicin and the Ti-Nb-Zr-O nanostructures indicated that a high drug loading content could result in a prolonged release process and a higher quantity of drug residues in the oxide nanostructures after drug release. Quick stem cell adhesion and spreading, as well as fast formation of extracellular matrix materials on the surfaces of the Ti-Nb-Zr-O nanostructures, were found. These findings make it possible to further explore the biomedical applications of the Ti-Nb-Zr-O nanostructure modified alloys especially clinical operation of orthopaedics by utilizing the nanostructures-based drug-release system.

Proximity effect depression of the critical temperature in two-phase Nb-Ti superconductors

International Nuclear Information System (INIS)

Meingast, C.; Daeumling, M.; Lee, P.J.; Larbalestier, D.C.

1987-01-01

The superconducting critical temperature of high critical current density Nb-Ti composites has been measured at various stages in the critical current optimization process. This process involves heat treatment steps which cause precipitation of normal α-Ti and make the matrix more Nb rich. T/sub c/ rises from 9.1 to 9.5 K during this stage. The final optimization stage involves extensive wire drawing during which the α-Ti precipitates are reduced to less than a coherence length in thickness. This does not result in a reduction in J/sub c/ but T/sub c/ is found to fall from 9.44 to 8.7 K during this step. The depression of T/sub c/ is found to be in fair agreement with the predicted proximity effect suppression of T/sub c/. Wires of optimum transport critical current density are seen to have T/sub c/ of around 9 K

Composite superconductors with copper-aluminum stabilizing matrix

International Nuclear Information System (INIS)

Keilin, V.E.; Anashkin, O.P.; Krivikh, A.V.; Kiriya, I.V.; Kovalev, I.A.; Dolgosheev, P.I.; Rychagov, A.V.; Sytnikov, V.E.

1992-01-01

A new type of composite superconductors has been developed. They consist of one or several (cabled) multifilamentary wires with low Cu-to-Sc ratio which are embedded and soldered into grooves made in matrix of rectangular cross-section. The latter consists of aluminum core metallurgically plated with a thin copper sheath. Such conductors combine the advantages of both aluminum and copper as stabilizing materials. They have low density, exhibit almost not magnetoresistance, are relatively cheap and can be produced in very long pieces. Copper plating offers the possibility of soft soldering thus ensuring good electrical and thermal contact between superconducting wires and stabilizing matrix, and helping to join pieces to each other. the properties of two Nb-Ti conductors (3.5 x 2 mm 2 and 7x4 mm 2 ) are described in more detail. The first is used in SC coils for whole-body magnetoresonance tomography, and the second will be used in a open-quotes thinclose quotes coil for charged particles detector. The influence of aluminum purity on SC magnet behavior is also briefly discussed

Valence band electronic structure of Pd based ternary chalcogenide superconductors

Energy Technology Data Exchange (ETDEWEB)

Lohani, H. [Institute of Physics, Sachivalaya Marg, Bhubaneswar 751005 (India); Homi Bhabha National Institute, Training School Complex, Anushakti Nagar, Mumbai 400085 (India); Mishra, P. [Institute of Physics, Sachivalaya Marg, Bhubaneswar 751005 (India); Goyal, R.; Awana, V.P.S. [National Physical Laboratory(CSIR), Dr. K. S. Krishnan Road, New Delhi 110012 (India); Sekhar, B.R., E-mail: sekhar@iopb.res.in [Institute of Physics, Sachivalaya Marg, Bhubaneswar 751005 (India); Homi Bhabha National Institute, Training School Complex, Anushakti Nagar, Mumbai 400085 (India)

2016-12-15

Highlights: • VB Photoemission study and DFT calculations on Pd based ternary superconductors are presented. • Nb{sub 2}Pd{sub 0.95}S{sub 5} shows a temperature dependent pseudogap. • VB spectral features of ternary superconductors are correlated to their structural geometry. - Abstract: We present a comparative study of the valence band electronic structure of Pd based ternary chalcogenide superconductors Nb{sub 2}Pd{sub 0.95}S{sub 5}, Ta{sub 2}Pd{sub 0.97}S{sub 6} and Ta{sub 2}Pd{sub 0.97}Te{sub 6} using experimental photoemission spectroscopy and density functional based theoretical calculations. We observe a qualitatively similarity between valence band (VB) spectra of Nb{sub 2}Pd{sub 0.95}S{sub 5} and Ta{sub 2}Pd{sub 0.97}S{sub 6}. Further, we find a pseudogap feature in Nb{sub 2}Pd{sub 0.95}S{sub 5} at low temperature, unlike other two compounds. We have correlated the structural geometry with the differences in VB spectra of these compounds. The different atomic packing in these compounds could vary the strength of inter-orbital hybridization among various atoms which leads to difference in their electronic structure as clearly observed in our DOS calculations.

Compounds of the type Ba/sub 3/Bsup(II)M/sub 2/sup(V)O/sub 9/ with Bsup(II) = Mg, Ca, Sr, Ba, and Msup(V) = Nb, Ta

Energy Technology Data Exchange (ETDEWEB)

Kemmler-Sack, S; Thumm, I; Herrmann, M [Tuebingen Univ. (Germany, F.R.). Lehrstuhl fuer Anorganische Chemie 2

1981-08-01

The hexagonal perovskites Ba/sub 3/Bsup(II)M/sub 2/sup(V)O/sub 9/ (Msup(V) = Nb, Ta) crystallize with Bsup(II) = Mg, Ca in a 3 L structure (sequence (c)/sub 3/) and Bsup(II) = Sr in the hexagonal BaTiO/sub 3/ type (6 L; sequence (hcc)/sub 2/) with an 1:2 order for the B and M ions. Intensity calculations for Ba/sub 3/SrNb/sub 2/O/sub 9/ and Ba/sub 3/SrTa/sub 2/O/sub 9/ gave in the space group P6/sub 3//mmc a refined, intensity related R' value of 8.4% (Nb) and 9.0% (Ta) respectively. For Bsup(II) = Ba the perovskite Ba/sub 3/BaTa/sub 2/O/sub 9/ has an orthorhombic distorted 6 L structure and forms with Ba/sub 3/SrTa/sub 2/O/sub 9/ a continuous series of mixed crystals (Ba/sub 3/Srsub(1-x)Basub(x)Ta/sub 2/O/sub 9/). In the system Ba/sub 3/Srsub(1-x)Basub(x)Nb/sub 2/O/sub 9/ the range of existence of the hexagonal BaTiO/sub 3/ type is confined to the Sr richer end. The pure Ba compound posesses a proper structure type (5 L: Ba/sub 5/BaNb/sub 3/vacantOsub(13.5)vacantsub(1.5)).

Fission of Al, Ti, Co, Zr, Nb, Ag, In, Nd, Sm, and Ta nuclei induced by 0.8-1.8 GeV photons

International Nuclear Information System (INIS)

Lima, D.A. de; Martins, J.B.; Tavares, O.A.P.

1989-01-01

Samples of Al, Ti, Co, Zr, Nb, Ag, In, Nd, Sm, and Ta elements in contact with solid state nuclear track detectors were exposed to 0.8-1.8 GeV bremsstrahlung beams at the 2.5-GeV Electron Synchrotron of the Bonn University. The detectors were processed to produce visible fission tracks for track analysis with optical microscopes. Absolute mean cross section per photon and fissility were evaluated. Results are discussed and compared with other photofission data as well as with estimates from the current fission models. A broad minimum found for nuclear fissility of 10 -4 -10 -3 covering the range 15 approx Z 2 /A approx 25 seems to confirm the predictions from the models. For Al and Ti nuclei the probability of fission amounts to approx 10 -1 . (author) [pt

Superconductivity in Ti3P-type compounds

International Nuclear Information System (INIS)

Wills, J.O.; Hein, R.A.; Waterstrat, R.M.

1978-01-01

A study of 12 intermetallic A 3 B compounds which crsytallize in the tetragonal Ti 3 P-type structure has revealed five new superconductors with transition temperatures below 1 K: Zr 3 Si, Zr 3 Ge, Zr 3 P, V 3 P, and Nb 3 Ge (extrapolated from the alloy series Nb-Ge-As). In addition, two compounds, Zr 3 Sb and Ta 3 Ge, having the Ni 3 P structure type are found to be superconducting below 1 K. Within the Ti 3 P-type compounds, those with the lighter ''B'' elements in a given column of the Periodic Table have the higher transition temperatures. Critical-magnetic-field and electrical-resistivity data are reported for the superconducting Ti 2 P-type compound Nb 3 P, which permit one to estimate the Ginzburg-Landau kappa parameter and the electronic-specific-heat coefficient γ. The kappa value of 8.4 indicates that this material is type II, and the γ value of 1.3 mJ/mole K 2 for Nb 3 P is probably related to its low transition temperature relative to many A15 compounds

Formation of Nb3Al in powder processed Nb-Al superconductors

International Nuclear Information System (INIS)

Johnson, P.E.

1987-05-01

In high magnetic fields, the critical current density is strongly dependent on the upper critical field, which is determined primarily by the stoichiometry of the Nb 3 Al. The critical temperature (T/sub c/), like the upper critical field, is considered to be a measure of the ''intrinsic'' quality of the superconductor, indicating the stoichiometry, order, and strain. If the A15 phase is stoichiometric and well ordered, a high T/sub c/ (and high H/sub C 2 /) is expected, regardless of the volume fraction of superconductor. On the other hand, if sigma phase is present with the A15, the resultant composition gradient across the sigma-A15 interface(s) requires that some of the A15 be off-stoichiometric, and therefore that the T/sub c/ (and H/sub C 2 /) be low. Thus the extent of the A15 (Nb 3 Al) reaction and the quality of the A15 formed are interdependent. This work focuses on the factors that control the extent of Nb 3 Al formation in Nb/Al powder wires. The morphology and content of the reacted and unreacted wires are studied in optical, SEM, and TEM micrographs. Critical current density data and its dependence on processing are explained in terms of the unreacted microstructure and its effect on the extent of Nb 3 Al formation. As a method of improving the critical current density, a new variation of the conventional powder process for wire manufacturing is developed and tested

Wide-band operation of quasi-optical distributed superconductor/insulator/superconductor mixers with epitaxial NbN/AlN/NbN junctions

International Nuclear Information System (INIS)

Kohjiro, S; Shitov, S V; Wang, Z; Uzawa, Y; Miki, S; Kawakami, A; Shoji, A

2004-01-01

For the optimum design of integrated receivers operating above the gap frequency of Nb, we have designed, fabricated and tested NbN-based quasi-optical superconductor/insulator/superconductor (SIS) mixers. The mixer chip incorporates a resonant half-wavelength epitaxial NbN/AlN/NbN junction, a twin-slot antenna and their coupling circuits. We adopted two kinds of coupling circuit between the antenna and the SIS junction: one is an in-phase feed with a length of 95 μm and the other is an anti-phase feed of 30 μm length. It was found that the anti-phase mixer reveals a 3 dB bandwidth of 43% of the centre frequency; the uncorrected double-sideband receiver noise temperature T RX = 691 K at 0.91 THz and T RX = 844 K at 0.80 THz, while 17% and T RX = 1250 K at 0.79 THz for the in-phase version. Possible reasons for this difference are discussed, which could be transmission loss and its robustness with respect to the variation of junction parameters. These experimental results suggest the NbN-based distributed mixer with the anti-phase feed is a better candidate for wide-band integrated receivers operating above 0.7 THz

Sintering study and properties of alumina matrix composites reinforced with NbC, TiC and TaC

International Nuclear Information System (INIS)

Tonello, K.P.S.; Trombini, V.; Bressiani, A.H.A.; Bressiani, J.C.

2011-01-01

Al_2O_3 based composite materials are very promising due to their good mechanical properties, and have been studied as an alternative for the production of materials with high wear resistance. In alumina based composites the addition of carbides can change and improve the sintering and mechanical properties of materials. The objective was to study the effect of adding small concentrations of NbC, TaC and TiC in the sintering, microstructure and mechanical properties of alumina composites. The sintering study was conducted in dilatometer, with heating rate of 20 ° C / min. up to 1800 ° C, and the study of microstructure and properties of the composites was performed in hot pressed samples, sintered at 1500°C/30min with constant pressure of 20MPa. The results indicated that the addition of carbides modified the sintering behavior and also indicated that the hardness and fracture toughness were improved by the presence of carbide particles. (author)

Petrochemical Characteristics and Age of Rare Metal (Ta-Nb Mineralization in Precambrian Pegmatites, Komu, Nigeria

Directory of Open Access Journals (Sweden)

A. OLUGBENGA

2010-06-01

Full Text Available The Precambrian pegmatites of Komu area intrude semi discordantly older rock types, such as biotite gneiss, amphibolites and pelitic schists. The pegmatites occur as near flat lying bodies. This study aims at elucidating the geological setting, petrography, geochemical features and age of mineralization of these pegmatite bodies, with a view to classifying them and knowing their economic potential. The petrographic analysis shows that the pegmatite samples contain mainly quartz (35%, plagioclase (15%, microcline (10% and muscovite (12% with accessories like tourmaline, tantalum, niobium and illmeno-rutiles. Geochemical analysis of the muscovites extracted from pegmatites show that these rocks are enriched in silica (>60% and Al2O3 (>12% and depleted in Fe2O3, MgO and TiO2. Trace element analysis shows that the pegmatites contain rare metals with moderately high Ta, Nb, Sn, Rb, Li and Cs values and depleted in Ti, Ba and Zr. Elemental ratios indicate low ratios of K/Cs, Th/U and K/Rb. Variation plots of Ta/(Ta+Nb versus Mn/ (Mn+Fe show that the pegmatites plot in the complex (beryl subtype field. The Na/K versus Sn, Nb, Rb variation plots show that the pegmatites of Komu area are mineralized and compare favourably with those of other mineralized pegma-tite areas like Egbe and Ijero in southwestern Nigeria. The variation plots of Ta versus K/Cs, and Ta/W versus Cs, also confirm rare metal mineralization of Komu pegmatites, which plot over the mineralized line of Beus and Gordiyenko. The K/Rb versus Rb, Cs and Sn plots indicate low K/Rb ratios indicating moderate differentiation. The Rare Earth Elements (REE show high heavy REE values and lower light REE values with prominent positive Ce anomaly and negative Eu anomaly from normalized chondrite plots. K/Ar dating of the age of mineralization of muscovites extracted from the pegmatite yielded late Pan-African ages between 502.8±13Ma and 514.5±13.2Ma. This period represents the cooling ages of the

Comparing Thermal Stability of NbTi and Nb$_3$Sn Wires

CERN Document Server

Breschi, M; Bottura, L; Devred, A; Trillaud, F

2009-01-01

The investigation of quenching in low temperature superconducting wires is of great relevance for a proper design of superconductive cables and magnets. This paper reports the experimental results of a vast measurement campaign of quench induced by laser pulses on NbTi and Nb$_{3}$Sn wires in pool boiling Helium I. A comparison of the quench behavior of two typical NbTi and Nb$_{3}$Sn wires is shown from different standpoints. Different qualitative behaviors of the voltage traces recorded during quenches and recoveries on NbTi and Nb$_{3}$Sn wires are reported and analyzed. It is shown that the Nb$_{3}$Sn wire exhibits a quench or no-quench behavior, whereas quenches and recoveries are exhibited by the NbTi wire. The two wires are also compared considering the behaviors of the two main parameters describing quench, i.e. quench energies and quench velocities, with respect to operation current and pulse duration and magnetic field. It is shown that the Nb$_{3}$Sn wire exhibits a ‘kink’ of the quench energy ...

Diffusion behavior in the films of Nb-Ti systems

International Nuclear Information System (INIS)

Yoshitake, Michiko; Yoshihara, Kazuhiro

1990-01-01

The diffusion behavior of substrate element into a deposited film was investigated. The observed systems were a Nb film/Ti substrate and a Ti film/Nb substrate. When the Nb film/Ti substrate was heated in a vacuum, Ti diffused very rapidly in the Nb film. The pre-exponential factor of the diffusion constant of Ti in the Nb film was 5.6x10 -2 m 2 s -1 , and the activation energy was 220 kJmol -1 . The observed activation energy is about 60% of that of Ti in the bulk Nb. On the other hand, when the Ti film/Nb substrate was heated in a vacuum, Nb did not diffuse so rapidly. Titanium diffused through the Nb film rapidly and was concentrated on the surface of the Nb film. The chemical state of the concentrated Ti was metallic, and neither titanium oxides nor titanium carbide was observed. Therefore, the driving force of the rapid diffusion of Ti in the Nb film is considered as the reduction of the surface energy of Nb film. The difference in the diffusion behavior between Ti through the Nb film and Nb through the Ti film is explained supposing that the segregation of Ti reduces the surface energy of the Nb film but the segregation of Nb does not reduce the surface energy of the Ti film. After heating of the Nb film/Ti substrate for a long time, a new phase was formed at the interface between the Nb film and the Ti substrate. The chemical composition of the new phase is about 50% of Ti and 50% of Nb. This phase has not been reported in the phase diagram of the bulk Ti-Nb system. The surface area of the Nb film is considered to be quite large, so the contribution of surface energy to the thermodynamic state of the Nb film cannot be neglected. Therefore, the chemical potential of the film is different from that of the bulk. Then, the new phase, which does not exist in the phase diagram of the bulk system, is formed by an interaction of the films. (author)

Production of multifilamentary Nb3Sn composites incorporating a high tin bronze

International Nuclear Information System (INIS)

Petrovich, A.; Zeithlin, B.A.; Walker, M.S.

1977-01-01

The economics and processing methods have been examined for the fabrication of multifilamentary Nb 3 Sn using a high tin bronze reactive matrix. Four conductor configurations utilizing the high tin bronze were compared with a conventional Cu-13 wt % Sn bronze. The most promising of these designs is potentially 40% lower in cost per ampere meter than the conventional composite. Large hydrostatic extrusion facilities, which are required for the high tin processing, are not presently available in this country but can be made by conversion of conventional presses. They exist in Europe. Experiments were conducted to investigate the applicability of hydrostatic extrusion, and billet components were successfully prepared using the hydrostatic extrusion technique. We have concluded that the economics, availability of facilities and initial fabrication results are favorable for this type of conductor and that the next stage in this program of scale up to extrusion and drawing of 2'' to 3'' diameter composite billets should be undertaken

Superconducting critical-current densities of commercial multifilamentary Nb3Sn(Ti) wires made by the bronze process

International Nuclear Information System (INIS)

Suenaga, M.; Tsuchiya, K.; Higuchi, N.; Tachikawa, K.

1985-01-01

Superconducting critical-current densities Jsub(c) in fields up to 24 T and at 4.2 and 1.8 K were measured for a number of commercial Nb 3 Sn wires which were alloyed with Ti. The best values of Jsub(c) at 20 T and at 4.2 and 1.8 K were 78 and 156 A mm -2 , respectively. In order to achieve these high current densities at H>20 T, it was shown that nonuniformity of the filaments had to be minimized. It was also shown that the grain size of Nb 3 Sn is not very important in determining Jsub(c) at these high magnetic fields, and that achieving high values of critical magnetic field Hsub(c2) is more important than small grain size. (author)

Formation of titanium dioxide nanotubes on Ti–30Nb–xTa alloys by anodizing

Energy Technology Data Exchange (ETDEWEB)

Kim, Eun-Sil [Department of Dental Materials and Research Center of Nano-Interface Activation for Biomaterials, School of Dentistry, Chosun University, Gwangju (Korea, Republic of); Jeong, Yong-Hoon [Department of Dental Materials and Research Center of Nano-Interface Activation for Biomaterials, School of Dentistry, Chosun University, Gwangju (Korea, Republic of); Biomechanics and Tissue Engineering Laboratory, Division of Orthodontics, College of Dentistry, The Ohio State University, Columbus, OH (United States); Choe, Han-Cheol, E-mail: hcchoe@chosun.ac.kr [Department of Dental Materials and Research Center of Nano-Interface Activation for Biomaterials, School of Dentistry, Chosun University, Gwangju (Korea, Republic of); Brantley, William A. [Division of Restorative, Prosthetic and Primary Care Dentistry, College of Dentistry, The Ohio State University, Columbus, OH (United States)

2013-12-31

The goal of this study was to investigate the formation of titanium dioxide nanotubes on the surface of cast Ti–30Nb–xTa alloys by anodizing. The anodization technique for creating the nanotubes utilized a potentiostat and an electrolyte containing 1 M H{sub 3}PO{sub 4} with 0.8 wt.% NaF. The grain size of the Ti–30Nb–xTa alloys increased as the Ta content increased. Using X-ray diffraction, for the Ti–30Nb alloy the main peaks were identified as α″ martensite with strong peaks of β phase. The phases in the Ti–30Nb–xTa alloys changed from a duplex (α″ + β) microstructure to solely β phase with increasing Ta content. The nanotubes that formed on the surface of the Ti–30Nb–xTa alloys were amorphous TiO{sub 2} without an evidence of the crystalline anatase or rutile forms of TiO{sub 2}. Scanning electron microscopy revealed that the average diameters of the small and large nanotubes on the Ti–30Nb alloy not containing Ta were approximately 100 nm and 400 nm, respectively, whereas the small and large nanotubes on the alloy had diameters of approximately 85 nm and 300 nm, respectively. As the Ta content increased from 0 to 15 wt.%, the average lengths of the nanotubes increased from 2 μm to 3.5 μm. Energy-dispersive X-ray spectroscopy indicated that the nanotubes were principally composed of Ti, Nb, Ta, O and F. Contact angle measurements showed that the nanotube surface had good wettability by water droplets. - Highlights: • TiO{sub 2} nanotube layers on anodized Ti-30Nb-xTa alloys have been investigated. • Nanotube surface had an amorphous structure without heat treatment. • Nanotube diameter of Ti-30Nb-xTa decreased, whereas tube layer increased with Ta content. • The nanotube surface exhibited the low contact angle and good wettability.

Formation of titanium dioxide nanotubes on Ti–30Nb–xTa alloys by anodizing

International Nuclear Information System (INIS)

Kim, Eun-Sil; Jeong, Yong-Hoon; Choe, Han-Cheol; Brantley, William A.

2013-01-01

The goal of this study was to investigate the formation of titanium dioxide nanotubes on the surface of cast Ti–30Nb–xTa alloys by anodizing. The anodization technique for creating the nanotubes utilized a potentiostat and an electrolyte containing 1 M H 3 PO 4 with 0.8 wt.% NaF. The grain size of the Ti–30Nb–xTa alloys increased as the Ta content increased. Using X-ray diffraction, for the Ti–30Nb alloy the main peaks were identified as α″ martensite with strong peaks of β phase. The phases in the Ti–30Nb–xTa alloys changed from a duplex (α″ + β) microstructure to solely β phase with increasing Ta content. The nanotubes that formed on the surface of the Ti–30Nb–xTa alloys were amorphous TiO 2 without an evidence of the crystalline anatase or rutile forms of TiO 2 . Scanning electron microscopy revealed that the average diameters of the small and large nanotubes on the Ti–30Nb alloy not containing Ta were approximately 100 nm and 400 nm, respectively, whereas the small and large nanotubes on the alloy had diameters of approximately 85 nm and 300 nm, respectively. As the Ta content increased from 0 to 15 wt.%, the average lengths of the nanotubes increased from 2 μm to 3.5 μm. Energy-dispersive X-ray spectroscopy indicated that the nanotubes were principally composed of Ti, Nb, Ta, O and F. Contact angle measurements showed that the nanotube surface had good wettability by water droplets. - Highlights: • TiO 2 nanotube layers on anodized Ti-30Nb-xTa alloys have been investigated. • Nanotube surface had an amorphous structure without heat treatment. • Nanotube diameter of Ti-30Nb-xTa decreased, whereas tube layer increased with Ta content. • The nanotube surface exhibited the low contact angle and good wettability

The structural representation and properties of mutually incommensurate composite crystal (BiS)xTS2 (T=Ti, V, Nb and Ta)

International Nuclear Information System (INIS)

Gotoh, Y.; Fujihisa, H.; Takeya, S.; Yamaguchi, I.

2006-01-01

The structural representation of mutually incommensurate composite crystal, (BiS) x TS 2 (T=Ti, V, Nb and Ta), with layered substructures has been described by superspace group approach. The incommensurate composite structures of (BiS) x TS 2 have been successfully characterized by the single-crystal X-ray-diffraction method. Temperature dependences of in-plane electrical resistivity of single composite crystals of (BiS) x TS 2 have been obtained by a standard d.c. four probe method in the range of 1.7-300 K. It has been found that the electronic transport properties of (BiS) x TS 2 compounds show metallic behavior below room temperature. (copyright 2006 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (Abstract Copyright [2006], Wiley Periodicals, Inc.)

Analysis of sodium metal by X-ray fluorescence spectrometry (I). Determination of Hf, Mo, Nb, Ta, Ti, V and Zr; Analisis de sodio metal por espectrometria de fluorescencia de rayos X. Determinacion de Hf, Mo, Nb, Ta, Ti, V y Zr

Energy Technology Data Exchange (ETDEWEB)

Diaz-Guerra, J P

1981-07-01

A method allowing the determination of trace quantities of Hf, Mo, Nb, Ta, Ti, Vi and Zr in sodium metal previous transformation into Na{sub 2}S0{sub 4} is described. The enrichment of the impurities is performed through a coprecipitation technique in sulfuric medium by using Fe{sup 3}+ as a collector and cupferron or phenyfluorone as the precipitating reagent. The matrix influence and the best concentration of the collector (10/{mu}/ml), adequate pH (1,3 or 4, respectively) and optimum filter type (Millipore BSWP02500 or BDWP04700, respectively) have been studied, as well as the precipitation recoveries corresponding to the reagent above. It has been demonstrated the batter efficiency of the cupferron for determining all the Impurities. Detection limits range from 0.01 to 0.2 ppm., depending on the element, for samples 4 g in weight. An automatic spectrometer attached to a 16 K minicomputer and X-ray tube with a gold anode (2250-2700 W) are used. The Interferences between the lines ZrK{alpha} (2{sup n}d order) - HfL{alpha} and TiK{beta} - VK {alpha} have been studied and the respective correction coefficients have been deduced. (Author) 8 refs.

Ion-beam mixing and thermal annealing of Al--Nb and Al--Ta thin films

International Nuclear Information System (INIS)

Rai, A.K.; Bhattacharya, R.S.; Mendiratta, M.G.; Subramanian, P.R.; Dimiduk, D.M.

1988-01-01

Ion-beam mixing and thermal annealing of thin, alternating layers of Al and Nb, as well as Al and Ta, were investigated by selected area diffraction and Rutherford backscattering. The individual layer thicknesses were adjusted to obtain the overall compositions as Al 3 Nb and Al 3 Ta. The films were ion mixed with 1 MeV Au + ions at a dose of 1 x 10 16 ions cm/sup -2/ . Uniform mixing and amorphization were achieved for both Al--Nb and Al--Ta systems. Equilibrium crystalline Al 3 Nb and Al 3 Ta phases were formed after annealing of ion mixed amorphous films at 400 0 C for 6 h. Unmixed films, however, remained unreacted at 400 0 C for 1 h. Partial reaction was observed in the unmixed film of Al--Nb at 400 0 C for 6 h. After annealing at 500 0 C for 1 h, a complete reaction and formation of Al 3 Nb and Al 3 Ta phases in the respective films were observed. The influence of thermodynamics on the phase formation by ion mixing and thermal annealing is discussed

Extraction behavior of Nb and Ta in HF solutions with tributyl phosphate

International Nuclear Information System (INIS)

Murakami, M.; Tsuto, S.; Ooe, K.; Goto, S.; Kudo, H.; Haba, H.; Kanaya, J.

2013-01-01

Extraction behavior of carrier-free Nb and Ta with tributyl phosphate (TBP) from HF solutions was studied by a batch method. Tantalum is extracted well to an organic phase, while Nb is left in an aqueous phase at 0.053-1.0 M HF concentrations. The similar extraction trends of Nb and Ta are shown in the solid phase extraction using a TBP resin. The extraction equilibria in the solid phase extraction are attained within ∼10 s. (author)

Anodic Fabrication of Ti-Nb-Zr-O Nanotube Arrays

Directory of Open Access Journals (Sweden)

Qiang Liu

2014-01-01

Full Text Available Highly ordered Ti-Nb-Zr-O nanotube arrays were fabricated through pulse anodic oxidation of Ti-Nb-Zr alloy in 1 M NaH2PO4 containing 0.5 wt% HF electrolytes. The effect of anodization parameters and Zr content on the microstructure and composition of Ti-Nb-Zr-O nanotubes was investigated using a scanning electron microscope equipped with energy dispersive X-ray analysis. It was found that length of the Ti-Nb-Zr-O nanotubes increased with increase of Zr contents. The diameter and the length of Ti-Nb-Zr-O nanotubes could be controlled by pulse voltage. XRD analysis of Ti-Nb-Zr-O samples annealed at 500°C in air indicated that the (101 diffraction peaks shifted from 25.78° to 25.05° for annealed Ti-Nb-Zr-O samples with different Zr contents because of larger lattice parameter of Ti-Nb-Zr-O compared to that of undoped TiO2.

Enhanced flux creep in Nb-Ti superconductors after an increase in temperature

International Nuclear Information System (INIS)

Cross, R.W.; Goldfarb, R.B.

1991-01-01

The magnetic fields of Superconducting Super Collider (SSC) dipole magnets change with time when the magnets are operated at constant current. The decay of the field is thought to be a consequence of flux creep in the Nb-Ti filaments in the superconducting cables. However, measured magnetic relaxation of small samples of SSC cable as a function of time is unlike the large decays that are observed in the fields of the actual magnets. We have made relaxation measurements on sample SSC conductors at 3.5 and 4.0 K after field cycling. The decay at both temperatures was 2.8% in 50 min. However, the relaxation measured after a temperature increase from 3.5 to 4.0 K was 4.8% in 50 min. A likely reason for the greater magnetization decay is that, after an increase in temperature, the Nb-Ti is in a supercritical state, with shielding currents flowing at a density greater than the new critical current density. This causes enhanced flux creep. We suggest that a small temperature rise during the operation of SSC magnets may contribute to the unexpectedly large magnetic field decay

Nickel Alloy, Corrosion and Heat-Resistant, Sheet, Strip, and Plate 72Ni - 15.5Cr - 0.95 (Cb (Nb) + Ta) - 2.5Ti - 0.70Al - 7.0Fe Consumable Electrode, Remelted or Vacuum Induction Melted, Solution Heat Treated, Precipitation-Hardenable

CERN Document Server

SAE Aerospace Standards. London

2012-01-01

Nickel Alloy, Corrosion and Heat-Resistant, Sheet, Strip, and Plate 72Ni - 15.5Cr - 0.95 (Cb (Nb) + Ta) - 2.5Ti - 0.70Al - 7.0Fe Consumable Electrode, Remelted or Vacuum Induction Melted, Solution Heat Treated, Precipitation-Hardenable

Comparing the thermal stability of NbTi and Nb3Sn wires

International Nuclear Information System (INIS)

Breschi, M; Trevisani, L; Bottura, L; Devred, A; Trillaud, F

2009-01-01

The investigation of quenching in low temperature superconducting wires is of great relevance for a proper design of superconductive cables and magnets. This paper reports the experimental results of a vast measurement campaign of quench induced by laser pulses on NbTi and Nb 3 Sn wires in pool boiling helium I. A comparison of the quench behavior of two typical NbTi and Nb 3 Sn wires is shown from different standpoints. Different qualitative behaviors of the voltage traces recorded during quenches and recoveries on NbTi and Nb 3 Sn wires are reported and analyzed. It is shown that the Nb 3 Sn wire exhibits a quench or no-quench behavior, whereas quenches and recoveries are exhibited by the NbTi wire. The two wires are also compared by considering the behaviors of the two main parameters describing quench, i.e. quench energies and quench velocities, with respect to operating current, pulse duration, and magnetic field. It is shown that the Nb 3 Sn wire exhibits a 'kink' of the quench energy versus current curve that makes the quench energy of Nb 3 Sn lower than that of NbTi at some intermediate current levels. Both the qualitative differences of the voltage traces and the different behaviors of quench energies and velocities are interpreted through a coupled electromagnetic-thermal model, with special emphasis on the detailed description of heat exchange with liquid helium.

Nano-nitride cathode catalysts of Ti, Ta, and Nb for polymer electrolyte fuel cells: Temperature-programmed desorption investigation of molecularly adsorbed oxygen at low temperature

KAUST Repository

Ohnishi, Ryohji

2013-01-10

TiN, NbN, TaN, and Ta3N5 nanoparticles synthesized using mesoporous graphitic (mpg)-C3N4 templates were investigated for the oxygen reduction reaction (ORR) as cathode catalysts for polymer electrolyte fuel cells. The temperature-programmed desorption (TPD) of molecularly adsorbed O2 at 120-170 K from these nanoparticles was examined, and the resulting amount and temperature of desorption were key factors determining the ORR activity. The size-dependent TiN nanoparticles (5-8 and 100 nm) were then examined. With decreasing particle size, the density of molecularly adsorbed O2 per unit of surface area increased, indicating that a decrease in particle size increases the number of active sites. It is hard to determine the electrochemical active surface area for nonmetal electrocatalysts (such as oxides or nitrides), because of the absence of proton adsorption/desorption peaks in the voltammograms. In this study, O2-TPD for molecularly adsorbed O2 at low temperature demonstrated that the amount and strength of adsorbed O2 were key factors determining the ORR activity. The properties of molecularly adsorbed O2 on cathode catalysts are discussed against the ORR activity. © 2012 American Chemical Society.

Effect of Nb on the Microstructure, Mechanical Properties, Corrosion Behavior, and Cytotoxicity of Ti-Nb Alloys.

Science.gov (United States)

Han, Mi-Kyung; Kim, Jai-Youl; Hwang, Moon-Jin; Song, Ho-Jun; Park, Yeong-Joon

2015-09-09

In this paper, the effects of Nb addition (5-20 wt %) on the microstructure, mechanical properties, corrosion behavior, and cytotoxicity of Ti-Nb alloys were investigated with the aim of understanding the relationship between phase/microstructure and various properties of Ti-xNb alloys. Phase/microstructure was analyzed using X-ray diffraction (XRD), SEM, and TEM. The results indicated that the Ti-xNb alloys (x = 10, 15, and 20 wt %) were mainly composed of α + β phases with precipitation of the isothermal ω phase. The volume percentage of the ω phase increased with increasing Nb content. We also investigated the effects of the alloying element Nb on the mechanical properties (including Vickers hardness and elastic modulus), oxidation protection ability, and corrosion behavior of Ti-xNb binary alloys. The mechanical properties and corrosion behavior of Ti-xNb alloys were found to be sensitive to Nb content. These experimental results indicated that the addition of Nb contributed to the hardening of cp-Ti and to the improvement of its oxidation resistance. Electrochemical experiments showed that the Ti-xNb alloys exhibited superior corrosion resistance to that of cp-Ti. The cytotoxicities of the Ti-xNb alloys were similar to that of pure titanium.

Multifunctional Beta Ti Alloy with Improved Specific Strength

Science.gov (United States)

Park, Chan Hee; Hong, Jae-Keun; Lee, Sang Won; Yeom, Jong-Taek

2017-12-01

Gum metals feature properties such as ultrahigh strength, ultralow elastic modulus, superelasticity, and superplasticity. They are composed of elements from Groups 4 and 5 of the periodic table and exist when the valance electron concentration (\\overline{e/a}) is 4.24; the bond order (\\overline{Bo}) is 2.87; and the "d" electron-orbital energy level (\\overline{Md}) is 2.45 eV. Typical compositions include Ti-23Nb-2Zr-0.7Ta-O and Ti-12Ta-9Nb-6Zr-3 V-O, which contain large amounts of heavy Group-5 elements such as Nb and Ta. In the present study, to improve the specific strength of a multifunctional beta Ti alloy, three alloys (Ti-20Nb-5Zr-1Fe-O, Ti-12Zr-10Mo-4Nb-O, and Ti-24Zr-9Cr-3Mo-O) were designed by satisfying the above three requirements while adding Fe, Mo, and Cr, which are not only lightweight but also have strong hardening effects. Microstructural and mechanical property analyses revealed that Ti-20Nb-5Zr-1Fe-O has a 25% higher specific strength than gum metal while maintaining an ultralow elastic modulus.

Studies on advanced superconductors for fusion device. Pt. 1. Present status of Nb3Sn conductors

International Nuclear Information System (INIS)

Tachikawa, Kyoji; Yamamoto, Junya

1996-03-01

Nb 3 Sn conductors have been developed with great expectation as an advanced high-field superconductor to be used in fusion devices of next generation. Furthermore, Nb 3 Sn conductors are being developed for NMR magnet and superconducting generator as well as for cryogen-free superconducting magnet. A variety of fabrication procedures, such as bronze process, internal tin process and Nb tube method, have been developed based on the diffusion reaction. Recently, Nb 3 Sn conductors with ultra-thin filaments have been fabricated for AC use. Both high-field and AC performances of Nb 3 Sn conductors have been significantly improved by alloying addition. The Ti-doped Nb 3 Sn conductor has generated 21.5T at 1.8K operation. This report summarizes manufacturing procedures, superconducting performances and applications of Nb 3 Sn conductors fabricated through different processes in different countries. More detailed subjects included in this report are high-field properties, AC properties, conductors for fusion with large current capacities, stress-strain effect and irradiation effect as well as standardization of critical current measurement method regarding to Nb 3 Sn conductors. Comprehensive grasp on the present status of Nb 3 Sn conductors provided by this report will act as a useful data base for the future planning of fusion devices. (author). 172 refs

Creep behavior of Ti3Al-Nb intermetallic alloys

International Nuclear Information System (INIS)

Yu, T.H.; Yue, W.J.; Koo, C.H.

1997-01-01

It is well known that Ti 3 Al-Nb alloys are potential materials for aerospace applications. The creep property is an important consideration when materials are used at high temperature. In this article, the effect of microstructure of Ti-25Al-10Nb alloy on the creep property was investigated, and the creep property of Ti-25Al-10Nb alloy modified by small addition of silicon 0.2 at.% or carbon 0.1 at.% was observed. The alloy with the addition of molybdenum to replace part of niobium 2 at.% was also studied. The experimental results show that the furnace-cooled Ti-25Al-10Nb alloy has superior creep resistance to the air-cooled Ti-25Al-10Nb alloy at 200 MPa, but exhibits poor creep resistance at 250 MPa or above. Small addition of silicon to the Ti-25Al-10Nb alloy may increase creep resistance. Small addition of carbon to the Ti-25Al-10Nb alloy may reduce creep resistance but raise rupture strain. Molybdenum is the most effective alloying element to increase creep resistance for the Ti-25Al-10Nb alloy. The creep mechanism of Ti-25Al-10Nb alloy is governed by dislocation climb. (orig.)

Analysis of sodium metal by X-ray fluorescence spectrometry (I). Determination of Hf, Mo, Nb, Ta, Ti, V and Zr

International Nuclear Information System (INIS)

Diaz-Guerra, J. P.

1981-01-01

A method allowing the determination of trace quantities of Hf, Mo, Nb, Ta, Ti, Vi and Zr in sodium metal previous transformation into Na 2 S0 4 is described. The enrichment of the impurities is performed through a coprecipitation technique in sulfuric medium by using Fe 3 + as a collector and cupferron or phenyfluorone as the precipitating reagent. The matrix influence and the best concentration of the collector (10/μ/ml), adequate pH (1,3 or 4, respectively) and optimum filter type (Millipore BSWP02500 or BDWP04700, respectively) have been studied, as well as the precipitation recoveries corresponding to the reagent above. It has been demonstrated the batter efficiency of the cupferron for determining all the Impurities. Detection limits range from 0.01 to 0.2 ppm., depending on the element, for samples 4 g in weight. An automatic spectrometer attached to a 16 K minicomputer and X-ray tube with a gold anode (2250-2700 W) are used. The Interferences between the lines ZrKα (2 n d order) - HfLα and TiKβ - VK α have been studied and the respective correction coefficients have been deduced. (Author) 8 refs

Contributions to the study of superconducting multifilamentary composites and cables

International Nuclear Information System (INIS)

Turck, B.

1992-03-01

This report is a collection of published papers in French and in English on superconducting composites and cables. All domains concerning the behaviour of superconductors in coils for field generation have been covered: critical current, current distribution, instabilities, losses in varying field. This document provides with expressions and criteria for conductor design, with conditions for achieving given performances and with criteria for design and optimization of structures of multifilamentary composites and cables. These publications have played a determining role in the understanding of the behaviour of superconductors and in their use in high performing magnets

Application of superconductivity to pulse fields

International Nuclear Information System (INIS)

Saito, Shigeo; Suzawa, Chizuru; Ohkura, Kengo; Nagata, Masayuki; Kawashima, Masao

1984-01-01

Numerous attempts to apply the superconductive phenomena of zero electrical resistivity to AC (pulsed) magnets in addition to conventional DC magnet fields are being made in the areas of poloidal coils of nuclear fusion, energy storage, rotary machines, and induction for stabilization of electric power systems. In pulsed superconductive magnets, the stability of the superconductivity and the generation of heat due to AC loss are serious problems. Based on the knowledge obtained through the development of various types of superconductors, magnets, cryostats, and other superconductive-related products, Cu-Ni/Cu/Nb-Ti mixed-matrix fine multifilamentary superconductor wire and the stable, low AC loss superconductors used therein, magnets, and FRP cryostats are developed and manufactured. (author)

The optimization of NbTi-Nb/sub 3/Sn high field superconducting magnet used for physics experiments

International Nuclear Information System (INIS)

Han, B.; Han, S.; Feng, Z.X.

1989-01-01

The approach to the optimum cost design of multigraded NbTi-Nb/sub 3/Sn high field superconducting magnet is proposed. Investigation shows that by reasonably choosing the contribution of NbTi and Nb/sub 3/Sn coils to the central field required and properly increasing the parameters β of both NbTi and Nb/sub 2/Sn coils, the optimum cost design of the NbTi-Nb/sub 3/Sn solenoid magnet can be obtained. This is the base on which the minimum cost design of multi-graded NbTi-Nb/sub 3/Sn high field superconducting magnet is reached. As an example, a calculation of a 14T three graded NbT-Nb/sub 3/Sn superconducting magnet with a bore of 31mm in diameter is given

Influence of boron vacancies on phase stability, bonding and structure of MB2 (M  =  Ti, Zr, Hf, V, Nb, Ta, Cr, Mo, W) with AlB2 type structure

International Nuclear Information System (INIS)

Dahlqvist, Martin; Rosen, Johanna; Jansson, Ulf

2015-01-01

Transition metal diborides in hexagonal AlB 2 type structure typically form stable MB 2 phases for group IV elements (M  =  Ti, Zr, Hf). For group V (M  =  V, Nb, Ta) and group VI (M  =  Cr, Mo, W) the stability is reduced and an alternative hexagonal rhombohedral MB 2 structure becomes more stable. In this work we investigate the effect of vacancies on the B-site in hexagonal MB 2 and its influence on the phase stability and the structure for TiB 2 , ZrB 2 , HfB 2 , VB 2 , NbB 2 , TaB 2 , CrB 2 , MoB 2 , and WB 2 using first-principles calculations. Selected phases are also analyzed with respect to electronic and bonding properties. We identify trends showing that MB 2 with M from group V and IV are stabilized when introducing B-vacancies, consistent with a decrease in the number of states at the Fermi level and by strengthening of the B–M interaction. The stabilization upon vacancy formation also increases when going from M in period 4 to period 6. For TiB 2 , ZrB 2 , and HfB 2 , introduction of B-vacancies have a destabilizing effect due to occupation of B–B antibonding orbitals close to the Fermi level and an increase in states at the Fermi level. (paper)

Mechanical and corrosion resistance of a new nanostructured Ti-Zr-Ta-Nb alloy.

Science.gov (United States)

Raducanu, D; Vasilescu, E; Cojocaru, V D; Cinca, I; Drob, P; Vasilescu, C; Drob, S I

2011-10-01

In this work, a multi-elementary Ti-10Zr-5Nb-5Ta alloy, with non-toxic alloying elements, was used to develop an accumulative roll bonding, ARB-type procedure in order to improve its structural and mechanical properties. The alloy was obtained by cold crucible semi-levitation melting technique and then was ARB deformed following a special route. After three ARB cycles, the total deformation degree per layer is about 86%; the calculated medium layer thickness is about 13 μm. The ARB processed alloy has a low Young's modulus of 46 GPa, a value very close to the value of the natural cortical bone (about 20 GPa). Data concerning ultimate tensile strength obtained for ARB processed alloy is rather high, suitable to be used as a material for bone substitute. Hardness of the ARB processed alloy is higher than that of the as-cast alloy, ensuring a better behaviour as a implant material. The tensile curve for the as-cast alloy shows an elastoplastic behaviour with a quite linear elastic behaviour and the tensile curve for the ARB processed alloy is quite similar with a strain-hardening elastoplastic body. Corrosion behaviour of the studied alloy revealed the improvement of the main electrochemical parameters, as a result of the positive influence of ARB processing. Lower corrosion and ion release rates for the ARB processed alloy than for the as-cast alloy, due to the favourable effect of ARB thermo-mechanical processing were obtained. Copyright © 2011 Elsevier Ltd. All rights reserved.

Resistivity of Weyl semimetals NbP and TaP under pressure

International Nuclear Information System (INIS)

Einaga, M.; Shimizu, K.; Hu, J.; Mao, Z.Q.; Politano, A.

2017-01-01

The resistivity of Weyl semimetals NbP and TaP has been investigated as a function of pressure and temperature. The behaviour of the resistivity as a function of pressure and temperature is closely correlated to the location of the Weyl points compared to the Fermi energy. The rapid increase of the resistivity in TaP and NbP under the application of 4.5 and 8.0 GPa is related with the shift of Weyl points, which affords a finite density of states near the Fermi energy. Specifically, we find that under pressure the Weyl points are situated above the Fermi energy. As regards the temperature behaviour, we detect a nonmonotonous behaviour of resistivity in TaP at 8.7 and 9.8 GPa as a function of temperature, whereas in the case of NbP the behaviour is more complicate. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Resistivity of Weyl semimetals NbP and TaP under pressure

Energy Technology Data Exchange (ETDEWEB)

Einaga, M.; Shimizu, K. [KYOKUGEN, Graduate School of Engineering Science, Osaka University, Toyonaka (Japan); Hu, J.; Mao, Z.Q. [Department of Physics and Engineering Physics, Tulane University, New Orleans, LA (United States); Politano, A. [Fondazione Istituto Italiano di Tecnologia, Graphene Labs, Genova (Italy)

2017-08-15

The resistivity of Weyl semimetals NbP and TaP has been investigated as a function of pressure and temperature. The behaviour of the resistivity as a function of pressure and temperature is closely correlated to the location of the Weyl points compared to the Fermi energy. The rapid increase of the resistivity in TaP and NbP under the application of 4.5 and 8.0 GPa is related with the shift of Weyl points, which affords a finite density of states near the Fermi energy. Specifically, we find that under pressure the Weyl points are situated above the Fermi energy. As regards the temperature behaviour, we detect a nonmonotonous behaviour of resistivity in TaP at 8.7 and 9.8 GPa as a function of temperature, whereas in the case of NbP the behaviour is more complicate. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Production of superconducting Nb3Sn wire using Nb or Nb(Ti) and Sn(Ga) solid solution powders

International Nuclear Information System (INIS)

Thieme, C.L.H.; Foner, S.

1991-01-01

This paper reports on superconducting Nb 3 Sn wire produced by the powder metallurgy method using Nb or Nb-2.9 at% Ti powder in combination with Sn-x at% Ga powders (x = 3, 4.2, 6.2 and 9.0). Ga additions to the Sn caused considerable solid solution hardening which improved its workability. It made the Nb-Sn(Ga) powder combinations convenient for swaging and extensive wire drawing. Anneals at 950 degrees C produced wires with an overall J c of 10 4 A/cm 2 at 21.9 T for wires with both Ti in the Nb and 6.2 at% Ga in the Sn. Comparison of this wire with the best Nb(Ti)-Cu-internal Sn(Ti) shows a higher J c per A15 areas, especially in fields of 22T and above

Method for preparing high transition temperature Nb.sub.3 Ge superconductors

Science.gov (United States)

Newkirk, Lawrence R.; Valencia, Flavio A.

1977-01-01

Bulk coatings of Nb.sub.3 Ge superconductors having transition temperatures in excess of 20 K are readily formed by a chemical vapor deposition technique involving the coreduction of NbCl.sub.5 and GeCl.sub.4 in the presence of hydrogen. The NbCl.sub.5 vapor may advantageously be formed quantitatively in the temperature range of about 250.degree. to 260.degree. C by the chlorination of Nb metal provided the partial pressure of the product NbCl.sub.5 vapor is maintained at or below about 0.1 atm.

Amphibole Fractional Crystallization and Delamination in Arc Roots: Implications for the `Missing' Nb Reservoir in the Earth

Science.gov (United States)

Galster, F.; Chatterjee, R. N.; Stockli, D. F.

2017-12-01

Most geologic processes should not fractionate Nb from Ta but Earth's major silicate reservoirs have subchondritic Nb/Ta values. Nb/Ta of >10000 basalts and basaltic andesites from different tectonic settings (GEOROC) cluster around 16, indistinguishable from upper mantle values. In contrast, Nb/Ta in more evolved arc volcanics have progressively lower values, reaching continental crust estimates, and correlate negatively with SiO2 (see figure) and positively with TiO2 and MgO. This global trend suggests that differentiation processes in magmatic arcs could explain bulk crustal Nb/Ta estimates. Understanding processes that govern fractionation of Nb from Ta in arcs can provide key insights on continental crust formation and help identify Earth's `missing' Nb reservoir. Ti-rich phases (rutile, titanite and ilmenite) have DNb/DTa values in the evolved liquid. Lack of correlation between Nb/Ta and K2O in global volcanic rocks implies that biotite plays a minor role in fractionating Nb from Ta during differentiation. Experimental petrology and evidence from exposed arc sections indicate that amphibole fractionation and delamination of island arc roots can explain the andesitic composition of bulk continental crust. Experimental studies have shown that amphibole Mg# correlate with DNb/DTa and amphibole could effectively fractionate Nb from Ta. Preliminary data from lower to middle crustal amphiboles from preserved arcs show sub- to super-chondritic Nb/Ta up to >60. This suggests that delamination of amphibole-rich cumulates can be a viable mechanism for the preferential removal of Nb from the continental crust. Future examination of Nb/Ta ratios in lower crustal amphiboles from various preserved arcs will provide improved constraints on the Nb-Ta paradox of the silicate Earth.

Microstructure and mechanical behavior of superelastic Ti-24Nb-0.5O and Ti-24Nb-0.5N biomedical alloys.

Science.gov (United States)

Ramarolahy, A; Castany, P; Prima, F; Laheurte, P; Péron, I; Gloriant, T

2012-05-01

In this study, the microstructure and the mechanical properties of two new biocompatible superelastic alloys, Ti-24Nb-0.5O and Ti-24Nb-0.5N (at.%), were investigated. Special attention was focused on the role of O and N addition on α(″) formation, supereleastic recovery and mechanical strength by comparison with the Ti-24Nb and Ti-26Nb (at.%) alloy compositions taken as references. Microstructures were characterized by optical microscopy, X-ray diffraction and transmission electron microscopy before and after deformation. The mechanical properties and the superelastic behavior were evaluated by conventional and cyclic tensile tests. High tensile strength, low Young's modulus, rather high superelastic recovery and excellent ductility were observed for both superelastic Ti-24Nb-0.5O and Ti-24Nb-0.5N alloys. Deformation twinning was shown to accommodate the plastic deformation in these alloys and only the {332} twinning system was observed to be activated by electron backscattered diffraction analyses. Copyright © 2012 Elsevier Ltd. All rights reserved.

Mechanism of generation of large (Ti,Nb,V)(C,N)-type precipitates in H13 + Nb tool steel

Science.gov (United States)

Xie, You; Cheng, Guo-guang; Chen, Lie; Zhang, Yan-dong; Yan, Qing-zhong

2016-11-01

The characteristics and generation mechanism of (Ti,Nb,V)(C,N) precipitates larger than 2 μm in Nb-containing H13 bar steel were studied. The results show that two types of (Ti,Nb,V)(C,N) phases exist—a Ti-V-rich one and an Nb-rich one—in the form of single or complex precipitates. The sizes of the single Ti-V-rich (Ti,Nb,V)(C,N) precipitates are mostly within 5 to 10 μm, whereas the sizes of the single Nb-rich precipitates are mostly 2-5 μm. The complex precipitates are larger and contain an inner Ti-V-rich layer and an outer Nb-rich layer. The compositional distribution of (Ti,Nb,V)(C,N) is concentrated. The average composition of the single Ti-V-rich phase is (Ti0.511V0.356Nb0.133)(C x N y ), whereas that for the single Nb-rich phase is (Ti0.061V0.263Nb0.676)(C x N y ). The calculation results based on the Scheil-Gulliver model in the Thermo-Calc software combining with the thermal stability experiments show that the large phases precipitate during the solidification process. With the development of solidification, the Ti-V-rich phase precipitates first and becomes homogeneous during the subsequent temperature reduction and heat treatment processes. The Nb-rich phase appears later.

Effect of Nb-doped TiO{sub 2} on nanocomposited aligned ZnO nanorod/TiO{sub 2}:Nb for dye-sensitized solar cells

Energy Technology Data Exchange (ETDEWEB)

Saurdi, I., E-mail: saurdy788@gmail.com; Ishak, A. [NANO-ElecTronic Centre (NET), Faculty of Electrical Engineering, Universiti Teknologi MARA (UiTM),40450 Shah Alam, Selangor (Malaysia); UiTM Sarawak Kampus Kota Samarahan Jalan Meranek, Sarawak (Malaysia); Shafura, A. K.; Azhar, N. E. A.; Mamat, M. H. [NANO-ElecTronic Centre (NET), Faculty of Electrical Engineering, Universiti Teknologi MARA (UiTM),40450 Shah Alam, Selangor (Malaysia); Malek, M. F.; Rusop, M. [NANO-ElecTronic Centre (NET), Faculty of Electrical Engineering, Universiti Teknologi MARA (UiTM),40450 Shah Alam, Selangor (Malaysia); NANO-SciTech Centre (NST), (Centre for Nano-Science and Nano-Technology), Institute of Science, Universiti Teknologi MARA - UiTM, 40450 Shah Alam, Selangor (Malaysia); Alrokayan, A. H. Salman; Khan, Haseeb A. [Department of Biochemistry, College of Science, Bldg. 5, King Saud University (KSU) P.O: 2455 Riyadh 1145 (Saudi Arabia)

2016-07-06

The Nb-doped TiO{sub 2} films were deposited on glass substrate at different Nb concentrations of 0 at.%, 1 at.%, 3 at.%, 5 at.% and 7 at.%, respectively and their electrical and structural properties were investigated. Subsequently, the Nb-doped TiO{sub 2} films were deposited on top of aligned ZnO Nanorod on ITO glass substrates using spin coating technique. The nanocomposited aligned ZnO nanorod/Nb-doped TiO{sub 2} (TiO{sub 2}:Nb) were coated with different Nb concentrations of 0 at.%, 1 at.%, 3 at.%, 5 at.% and 7 at.%, respectively. The Dye-sensitized solar cells were fabricated from the nanocomposited aligned ZnO nanorod/TiO{sub 2}:Nb photoanodes and their effects on the performance of the DSSCs were investigated. From the solar simulator measurement of DSSC the solar energy conversion efficiency (η) of 5.376% under AM 1.5 was obtained for the ZnO nanorod/TiO{sub 2}:Nb-5at.%.

High-temperature superconductors make major progress

CERN Multimedia

CERN Bulletin

2014-01-01

This month's Nature Materials featured an important breakthrough for high-temperature superconductors. A new method has been found for processing Bi-2212 high-temperature superconducting round wire in order to drastically increase its critical current density. The result confirms that this conductor is a serious candidate for future very-high-field magnets.   This image shows the cross-section of two Bi-2212 wires. The bottom wire has less leakage and void porosity due to a heat treatment done at an overpressure of 100 bar - about 100 times the pressure used to produce the top wire (image from [Nature Materials, Vol. 13 (2014), 10.1038/nmat3887]). The workhorse for building superconducting accelerator magnets has been, so far, the Niobium-Titanium (Nb-Ti) alloy superconductor. But with Nb-Ti having reached its full potential, other conductors must be used to operate in higher magnetic fields beyond those reached with the LHC magnets. Today, the intermetallic Niobium-Tin (Nb3Sn) is th...

Dissolving of Nb and Ti carbonitride precipitates in microalloyed steels

Institute of Scientific and Technical Information of China (English)

Wenjin Nie; Shanwu Yang; Shaoqiang Yuan; Xinlai He

2003-01-01

The dissolving behaviour of Nb and Ti carbonitride precipitates in microalloyed steels during isothermal holding at 1300℃ was investigated by Transmission electron microscopy (TEM) and energy dispersion x-ray spectrum (EDX). It was found that all precipitates in Nb-Ti microalloyed steel are (Nb, Ti)(C,N). With holding time increasing, the atomic ratio of Nb/Ti in precipitates decrease gradually. These precipitates still existe even after holding for 48 h at 1300℃ while Nb(C,N) precipitates dissolve away in Nb microalloyed steel only after 4 h at the same temperature. These results show that formation and thermostability of precipitates are considerably influenced by interaction between Nb and Ti.

Charge Berezinskii-Kosterlitz-Thouless transition in superconducting NbTiN films

Energy Technology Data Exchange (ETDEWEB)

Mironov, Alexey Yu.; Silevitch, Daniel M.; Proslier, Thomas; Postolova, Svetlana V.; Burdastyh, Maria V.; Gutakovskii, Anton K.; Rosenbaum, Thomas F.; Vinokur, Valerii V.; Baturina, Tatyana I.

2018-03-06

Three decades after the prediction of charge-vortex duality in the critical vicinity of the two-dimensional superconductor-insulator transition (SIT), one of the fundamental implications of this duality-the charge Berezinskii-Kosterlitz-Thouless (BKT) transition that should occur on the insulating side of the SIT-has remained unobserved. The dual picture of the process points to the existence of a superinsulating state endowed with zero conductance at finite temperature. Here, we report the observation of the charge BKT transition on the insulating side of the SIT in 10 nm thick NbTiN films, identified by the BKT critical behavior of the temperature and magnetic field dependent resistance, and map out the magnetic-field dependence of the critical temperature of the charge BKT transition. Finally, we ascertain the effects of the finite electrostatic screening length and its divergence at the magnetic field-tuned approach to the superconductor-insulator transition.

Mesoporous (Ta, Nb3W7 Modified with Stearic Acid Used as Solid Acids for Esterification

Directory of Open Access Journals (Sweden)

Fei Chang

2017-01-01

Full Text Available Mesoporous solid acids Ta3W7 and Nb3W7 were prepared from TaCl5 and NbCl5 with WCl6 in the presence of stearic acid (SA via a sol-gel method, respectively. For comparison, mesoporous Ta3W7-P123 mixed oxides and mesoporous Nb3W7-P123 mixed oxides were synthesized in the same way. The catalysts were characterized through TGA, XRD, SEM, TEM, BET, and NH3-TPD. Experimental results showed that Ta3W7-SA and Nb3W7-SA exhibited several advantages such as higher activity, shorter preparation period, lower cost, stronger acid sites, and higher surface area, which had potential to be used as mesoporous heterogeneous catalysts in biodiesel production.

Thermomechanical processing of In-containing β-type Ti-Nb alloys.

Science.gov (United States)

Pilz, Stefan; Geissler, David; Calin, Mariana; Eckert, Jürgen; Zimmermann, Martina; Freudenberger, Jens; Gebert, Annett

2018-03-01

In this study, the effect of thermomechanical processing on microstructure evolution of the indium-containing β-type Ti alloys (Ti-40Nb)-3.5In and (Ti-36Nb)-3.5In was examined. Both alloys show an increased β-phase stability compared to binary alloys due to In additions. This leads to a reduced α''-phase fraction in the solution treated and recrystallized state in the case of (Ti-36Nb)-3.5In and to the suppression of stress-induced α'' formation and deformation twinning for (Ti-40Nb)-3.5In. The mechanical properties of the alloys were subsequently studied by quasistatic tensile tests in the recrystallized state, revealing reduced Young's modulus values of 58GPa ((Ti-40Nb)-3.5In) and 56GPa ((Ti-36Nb)-3.5In) compared to 60GPa as determined for Ti-40Nb. For both In-containing alloys the ultimate tensile strength is in the range of 560MPa. Due to the suppressed α'' formation, (Ti-40Nb)-3.5In exhibits a linear elastic deformation behavior during tensile loading together with a low Young's modulus and is therefore promising for load-bearing implants. Copyright © 2018 Elsevier Ltd. All rights reserved.

Effect of nitrogen addition on superelasticity of Ti-Zr-Nb alloys

International Nuclear Information System (INIS)

Tahara, Masaki; Kim, Hee Young; Miyazaki, Shuichi; Inamura, Tomonari; Hosoda, Hideki

2008-01-01

Recently, the Ti-Zr-Nb alloys have been developed as Ni-free shape memory and superelastic alloys. In this study, the effect of Nb and nitrogen (N) contents on martensitic transformation behavior, shape memory effect and superelasticity in Ti-18Zr-(12-16)Nb-(0-1.0)N (at%) alloys were investigated using tensile tests, optical microscopy and X-ray diffraction. Shape memory effect was observed in Ti-18Zr-(12-13)Nb and Ti-18Zr-12Nb-0.5N alloys at room temperature. The superelastic behavior appeared by the increase of Nb or N content. The Ti-18Zr-(14-15)Nb, Ti-18Zr-(13-14)Nb-0.5N and Ti-18Zr-(12-14)Nb-1.0N alloys exhibited the superelasticity at room temperature. The martensitic transformation start temperature (M s ) decreased by 75 K with 1 at% increase of N content for Ti-18Zr-13Nb alloy. The critical stress for slip deformation and the stress for inducing the martensitic transformation increased with increasing N content. The superelastic recovery strain was also increased by adding N. The maximum recovery strain of 5.0% was obtained in the Ti-18Zr-14Nb-0.5N alloy. (author)

Structural stability of characteristic interface for NiTi/Nb Nanowire: First-Principle study

Science.gov (United States)

Li, G. F.; Zheng, H. Z.; Shu, X. Y.; Peng, P.

2016-01-01

Compared with some other conventional interface models, the interface of NiTi(211)/Nb(220) in NiTiNb metal nanocomposite had been simulated and analyzed carefully. Results show that only several interface models, i.e., NiTi(100)/Nb(100)(Ni⃡Nb), NiTi(110)/Nb(110) and NiTi(211)/Nb(220), can be formed accordingly with their negative formation enthalpy. Therein the cohesive energy Δ E and Griffith rupture work W of NiTi(211)/Nb(220) interface model are the lowest among them. Density of states shows that there exists only one electronic bonding peak for NiTi(211)/Nb(220) interface model at -2.5 eV. Electron density difference of NiTi(211)/ Nb(220) shows that the Nb-Nb, Nb-Ti and Nb-Ni bonding characters seem like so peaceful as a fabric twisting every atom, which is different from conventional metallic bonding performance. Such appearance can be deduced that the metallic bonding between Nb-Nb, Nb-Ti and Nb-Ni in NiTi(211)/Nb(220) may be affected by its nanostructure called nanometer size effect. Thus, our findings open an avenue for detailed and comprehensive studies of nanocomposite.

Evidence for Nb-Ta Occurrences in the Syn-Tectonic Pan-African Mayo Salah Leucogranite (Northern Cameroon: Constraints from Nb-Ta Oxide Mineralogy, Geochemistry and U-Pb LA-ICP-MS Geochronology on Columbite and Monazite

Directory of Open Access Journals (Sweden)

Periclex Martial Fosso Tchunte

2018-04-01

Full Text Available The Mayo Salah pluton, which is located in the North-Cameroon domain of Central African Bold Belt (CAFB, is emplaced as a laccolith in volcano-sedimentary schists of Poli series, and displays features of Rare-metal Granite (RMG. It is made of two main rock groups: (1 the metaluminous barren muscovite granite (MsG and (2 the Nb-Ta bearing peraluminous leucogranite (MsL which expresses four subtypes. The evolved Rare-element MsL is subalkaline, slightly peraluminous (ASI = 1.01–1.21, and it displays flat REE chondrite-normalized patterns with a strong negative Eu anomaly (Eu/Eu* = 0.02–0.20. It belongs to the peraluminous low phosphorus Rare-element Granites and L-type igneous rocks, as shown by the relatively low Zr/Hf (4.8–14 and Nb/Ta (1.4–9.0 ratios and the positive slope of the Zr-Hf-Nb-Ta profile in spider diagrams. The rare-element-bearing mineral is represented by columbite-group minerals (CGM and other Nb-Ta-oxides (Nb-rutile and pyrochlore supergroup minerals. The CGM is classified as Mn-columbite, with Ta# and Mn# ratios increasing from core to rim. Two stages of mineralization are identified; the earliest stage (CGM-I consists in scattered tabular or prismatic euhedral grains that were related to magmatic fractionation. The latest stage (CGM-II is expressed as a Ta-rich Mn hydrothermal CGM episode represented as rims and/overgrowths around and/or as veinlet crosscutting CGM-I or in cleavage planes of muscovite. The U-Pb dating of columbite and monazite of the Mayo Salah leucogranite indicates a late-Neoproterozoic magmatic-hydrothermal mineralization event from 603.2 ± 5.3 to 581.6 ± 7.2 Ma, as consistent with both late D2 to D3 events that were recorded in the CAFB in Cameroon, and the associated continental collision environment. The Nb-Ta mineralization of the Mayo Salah pluton provides evidence for the presence of RMG in Northern Cameroon of CAFB, and its temporal association with the youngest period of metallogenic epoch

On the Effects of Hot Forging and Hot Rolling on the Microstructural Development and Mechanical Response of a Biocompatible Ti Alloy

Science.gov (United States)

Okazaki, Yoshimitsu

2012-01-01

Zr, Nb, and Ta as alloying elements for Ti alloys are important for attaining superior corrosion resistance and biocompatibility in the long term. However, note that the addition of excess Nb and Ta to Ti alloys leads to higher manufacturing cost. To develop low-cost manufacturing processes, the effects of hot-forging and continuous-hot-rolling conditions on the microstructure, mechanical properties, hot forgeability, and fatigue strength of Ti-15Zr-4Nb-4Ta alloy were investigated. The temperature dependences with a temperature difference (ΔT) from β-transus temperature (Tβ) for the volume fraction of the α- and β-phases were almost the same for both Ti-15Zr-4Nb-4Ta and Ti-6Al-4V alloys. In the α-β-forged Ti-15Zr-4Nb-4Ta alloy, a fine granular α-phase structure containing a fine granular β-phase at grain boundaries of an equiaxed α-phase was observed. The Ti-15Zr-4Nb-4Ta alloy billet forged at Tβ-(30 to 50) °C exhibited high strength and excellent ductility. The effects of forging ratio on mechanical strength and ductility were small at a forging ratio of more than 3. The maximum strength (σmax) markedly increased with decreasing testing temperature below Tβ. The reduction in area (R.A.) value slowly decreased with decreasing testing temperature below Tβ. The temperature dependences of σmax for the Ti-15Zr-4Nb-4Ta and Ti-6Al-4V alloys show the same tendency and might be caused by the temperature difference (ΔT) from Tβ. It was clarified that Ti-15Zr-4Nb-4Ta alloy could be manufactured using the same manufacturing process as for previously approved Ti-6Al-4V alloy, taking into account the difference (ΔT) between Tβ and heat treatment temperature. Also, the manufacturing equivalency of Ti-15Zr-4Nb-4Ta alloy to obtain marketing approval of implants was established. Thus, it was concluded that continuous hot rolling is useful for manufacturing α-β-type Ti alloy.

Nb3Sn single crystals, polycrystals and multifilamentary wires: common and different features in the magnetic response

International Nuclear Information System (INIS)

Adesso, M G; Uglietti, D; Fluekiger, R; Polichetti, M; Pace, S

2006-01-01

The magnetic response of different Nb 3 Sn samples has been investigated studying the temperature dependence of both the 1st and 3rd harmonics of the AC magnetic susceptibility, in presence of a DC field up to 19 T. In single crystal and in polycrystalline samples, the occurrence of a Peak Effect was observed within DC magnetic fields ranging from 3 T to about 13 T. It corresponds to a transition in the vortex lattice between the Bragg Glass phase and a disordered phase. This transition has been also detected at higher magnetic fields in both the samples, thanks to the 3rd harmonics measurements. In contrast to single crystals and polycrystals, no Peak Effect and no indications about the Bragg/disordered phase transition have been detected in the analysed multifilamentary wires

Solubilization and precipitation of {omega} and {alpha} phases in Ti-30 Nb and Ti-35 Nb alloys; Solubilizacao e precipitacao de fases {omega} e {alpha} nas ligas Ti-30Nb e Ti-35Nb

Energy Technology Data Exchange (ETDEWEB)

Hayama, A.O.F.; Lopes, J.F.S.C.; Caram, R., E-mail: alexandrah@fem.unicamp.b [Universidade Estadual de Campinas (DEMa/FEM/UNICAMP), SP (Brazil). Fac. de Engenharia Mecanica. Dept. de Engenharia de Materiais

2010-07-01

This work presents the main results of the characterization of Ti-30Nb and Ti-35Nb alloys (wt%) submitted to the solutioning heat treatment following by aging. Samples were obtained by electric arc melting, followed by solution heat treatment at 1000 deg C during 8 hours and cooling in water, the microstructure obtained is formed by {beta} and {alpha} phases. Samples were aged at 260 and 400 deg C during periods of time varying from 1 to 240 min. Characterization was performed using light optical microscopy, X-ray diffraction, Young's modulus measurements by acoustic emission and Vickers hardness. The results show the presence of {beta} and {alpha}{sup '}' phases in samples of the Ti-30Nb alloy aged at 260 deg C. In samples aged at 400 deg C, precipitation of {omega} and {alpha}{sup '}' phases took place, and due to this fact, an increase in Young's modulus and in hardness occurred. (author)

Systematic study on the electronic structure and mechanical properties of X2BC (X = Mo, Ti, V, Zr, Nb, Hf, Ta and W)

International Nuclear Information System (INIS)

Bolvardi, H; Emmerlich, J; To Baben, M; Music, D; Schneider, J M; Von Appen, J; Dronskowski, R

2013-01-01

In this work the electronic structure and mechanical properties of the phases X 2 BC with X =Ti, V, Zr, Nb, Mo, Hf, Ta, W (Mo 2 BC-prototype) were studied using ab initio calculations. As the valence electron concentration (VEC) per atom is increased by substitution of the transition metal X, the six very strong bonds between the transition metal and the carbon shift to lower energies relative to the Fermi level, thereby increasing the bulk modulus to values of up to 350 GPa, which corresponds to 93% of the value reported for c-BN. Systems with higher VEC appear to be ductile as inferred from both the more positive Cauchy pressure and the larger value of the bulk to shear modulus ratio (B/G). The more ductile behavior is a result of the more delocalized interatomic interactions due to larger orbital overlap in smaller unit cells. The calculated phase stabilities show an increasing trend as the VEC is decreased. This rather unusual combination of high stiffness and moderate ductility renders X 2 BC compounds with X = Ta, Mo and W as promising candidates for protection of cutting and forming tools.

Thermo-magnetic instabilities in Nb3Sn Superconducting Accelerator Magnets

International Nuclear Information System (INIS)

Bordini, Bernardo; Pisa U.

2006-01-01

The advance of High Energy Physics research using circulating accelerators strongly depends on increasing the magnetic bending field which accelerator magnets provide. To achieve high fields, the most powerful present-day accelerator magnets employ NbTi superconducting technology; however, with the start up of Large Hadron Collider (LHC) in 2007, NbTi magnets will have reached the maximum field allowed by the intrinsic properties of this superconductor. A further increase of the field strength necessarily requires a change in superconductor material; the best candidate is Nb 3 Sn. Several laboratories in the US and Europe are currently working on developing Nb 3 Sn accelerator magnets, and although these magnets have great potential, it is suspected that their performance may be fundamentally limited by conductor thermo-magnetic instabilities: an idea first proposed by the Fermilab High Field Magnet group early in 2003. This thesis presents a study of thermo-magnetic instability in high field Nb 3 Sn accelerator magnets. In this chapter the following topics are described: the role of superconducting magnets in High Energy Physics; the main characteristics of superconductors for accelerator magnets; typical measurements of current capability in superconducting strands; the properties of Nb 3 Sn; a description of the manufacturing process of Nb 3 Sn strands; superconducting cables; a typical layout of superconducting accelerator magnets; the current state of the art of Nb 3 Sn accelerator magnets; the High Field Magnet program at Fermilab; and the scope of the thesis

Fabrication of Nb_3Al superconductor by the optimized mechanical alloying method with low temperature

International Nuclear Information System (INIS)

Zhang, Y.; Lin, W.J.; Xu, L.Y.; Yang, D.W.; Chen, Y.L.; Li, P.Y.; Pan, X.F.; Yan, G.; Zhao, Y.

2016-01-01

Highlights: • Due to a much better strain tolerance than Nb_3Sn, Nb_3Al has been considered as an excellent candidate for making high field magnets. At present, the Nb_3Al superconducting wires were prepared mainly by the Jelly-roll method combined with a rapid heating and quenching (RHQ) heat treatment at around 2000 °C. In this study, Nb_3Al superconductor with T_c of 15.6 K is directly prepared with a mechanical alloying method followed by a low temperature annealing at 800 to 900 °C. Our results hint the possibility that Nb_3Al superconducting wire with high performance can be prepared below the melting point of Cu (1080 °C) by a conventional powder in tube (PIT) method, thus effectively avoiding high temperature heat treatment and RHQ device. - Abstract: Mechanical alloying was used to synthesize Nb_3Al superconductor successfully, and the process was optimization under various preparation conditions. In the current study, Nb_3Al superconductor with T_c of 15.6 K was directly prepared from high quality Nb (Al) solid solution by mechanical alloying method and heat treatment at a low temperature of 800 to 900 °C. The results showed that Nb_3Al superconducting wire with high performance could be prepared after heat treatment below the melting point of Cu (1080°C) and using Nb (Al) solid solution and conventional powder in tube (PIT) method, thus effectively avoiding ultra-high temperature heat treatment and special rapid heating and quenching(RHQ) device.

V3Si multifilamentary superconductor with high overall Jc

International Nuclear Information System (INIS)

Takeuchi, Takao; Inoue, Kiyoshi; Kosuge, Michio; Iijima, Yasuo; Watanabe, Kazuo

1994-01-01

V 3 Si is one of the A15-type superconducting compounds from which single crystals can be quite easily obtained due to the nature of the equilibrium phase diagram. Thus, the fundamental characteristics of A15 compounds (such as electronic structure and cubic-to-tetragonal structural transformation) have been studied with this compound. V 3 Si is, however, also promising in practical use as an alternative to Nb 3 Sn for high field magnets, since the upper critical field H c2 (4.2 K) is more than 20 T. Although the open-quotes bronze process,close quotes the established commercial process to produce Nb 3 Sn conductors, is also available for V 3 Si, the ternary section of the Cu-V-Si phase diagram indicates two diffusion paths are possible: One from the bronze with low Si content (Si 3 Si, and the other from the bronze with higher Si content to V 3 Si via V 5 Si 3 . The high Si bronze is likely to be advantageous in reducing the bronze volume fraction and hence achieving high overall critical current density J c . This is because the initially formed V 5 Si 3 is eventually converted to V 3 Si as long as the total proportion of V to Si in the composite (overall V/Si molar ratio) is kept around 3. However, long times at high temperatures are necessary for appreciable V 3 Si layer growth, thereby yielding grain growth of V 3 Si and lowering the J c of the V 3 Si compound and the overall J c accordingly. In the present study, in order to improve the overall J c , the authors have realized ∼1μm filament diameter by preparing a double-stacked Cu-8.5at.%Si/V composite. The primary bundle is sheathed with a Ta tube. The Si in the bronze inside the Ta is available only for the diffusion reaction, and the overall V/Si ratios is ∼3

Superconductor composite and method of making the same

Energy Technology Data Exchange (ETDEWEB)

1980-02-27

A superconductor composite is described, comprising (a) a matrix body of material having substantial electrical resistivity at superconducting temperatures; (b) elongate tubular members of a metal superconducting at superconducting temperatures and workable by reduction to decrease its transverse area and elongate its length, the tubular members being parallel and spaced within the matrix and bonded to it to facilitate heat transfer; and (c) stabilizing cores within the tubular members and in thermal and electrical contact with them, the cores being of a workable aluminium or copper material having an electrical resistivity of not more than 10/sup -7/ ohm-cm at superconducting temperatures and sufficient to stabilize the superconductor at superconducting temperatures. The matrix is an aluminium alloy having an electrical resistivity of at least 10/sup -7/ ohm-cm and having a flow stress such that the flow stress ratio between the superconducting and matrix materials does not exceed 10. The elongate tubular members may consist of, or contain, the following metals or their alloys: Nb, Zr, Hf, V, Mo, Re, W, Ta, Ti.

Superconductor composite and method of making the same

International Nuclear Information System (INIS)

1980-01-01

A superconductor composite is described, comprising (a) a matrix body of material having substantial electrical resistivity at superconducting temperatures; (b) elongate tubular members of a metal superconducting at superconducting temperatures and workable by reduction to decrease its transverse area and elongate its length, the tubular members being parallel and spaced within the matrix and bonded to it to facilitate heat transfer; and (c) stabilizing cores within the tubular members and in thermal and electrical contact with them, the cores being of a workable aluminium or copper material having an electrical resistivity of not more than 10 -7 ohm-cm at superconducting temperatures and sufficient to stabilize the superconductor at superconducting temperatures. The matrix is an aluminium alloy having an electrical resistivity of at least 10 -7 ohm-cm and having a flow stress such that the flow stress ratio between the superconducting and matrix materials does not exceed 10. The elongate tubular members may consist of, or contain, the following metals or their alloys: Nb, Zr, Hf, V, Mo, Re, W, Ta, Ti. (U.K.)

Surface microstructures and corrosion resistance of Ni-Ti-Nb shape memory thin films

Science.gov (United States)

Li, Kun; Li, Yan; Huang, Xu; Gibson, Des; Zheng, Yang; Liu, Jiao; Sun, Lu; Fu, Yong Qing

2017-08-01

Ni-Ti-Nb and Ni-Ti shape memory thin films were sputter-deposited onto silicon substrates and annealed at 600 °C for crystallization. X-ray diffraction (XRD) measurements indicated that all of the annealed Ni-Ti-Nb films were composed of crystalline Ni-Ti (Nb) and Nb-rich grains. X-ray photoelectron spectroscopy (XPS) tests showed that the surfaces of Ni-Ti-Nb films were covered with Ti oxides, NiO and Nb2O5. The corrosion resistance of the Ni-Ti-Nb films in 3.5 wt.% NaCl solution was investigated using electrochemical tests such as open-circuit potential (OCP) and potentio-dynamic polarization tests. Ni-Ti-Nb films showed higher OCPs, higher corrosion potentials (Ecorr) and lower corrosion current densities (icorr) than the binary Ni-Ti film, which indicated a better corrosion resistance. The reason may be that Nb additions modified the passive layer on the film surface. The OCPs of Ni-Ti-Nb films increased with further Nb additions, whereas no apparent difference of Ecorr and icorr was found among the Ni-Ti-Nb films.

Pyrochlore type semiconducting ceramic oxides in Ca-Ce-Ti-M-O system (M = Nb or Ta)-Structure, microstructure and electrical properties

International Nuclear Information System (INIS)

Deepa, M.; Prabhakar Rao, P.; Radhakrishnan, A.N.; Sibi, K.S.; Koshy, Peter

2009-01-01

A new series of pyrochlore type ceramic semiconducting oxides in Ca-Ce-Ti-M-O (M = Nb or Ta) system has been synthesized by the conventional ceramic route. The electrical conductivity measurements show that these oxides exhibit semiconducting behavior and the conductivity increases with the Ce content in the compound. Activation energy of the current carriers is in the range of 0.5-1.6 eV. The electrical conductivity in these oxides is due to the presence of Ce 3+ , which remains in the reduced state without being oxidized to Ce 4+ by structural stabilization. The photoluminescence and X-ray photoelectron spectroscopy analysis corroborate the presence of Ce in the 3+ state. Impedance spectral analysis is carried out to evaluate the transport properties and indicates that the conduction in these compounds is mainly due to electronic contribution. The X-ray powder diffraction and Raman spectroscopy analysis establishes that these oxides belong to a cubic pyrochlore type structure.

Pyrochlore type semiconducting ceramic oxides in Ca-Ce-Ti-M-O system (M = Nb or Ta)-Structure, microstructure and electrical properties

Energy Technology Data Exchange (ETDEWEB)

Deepa, M. [Materials and Minerals Division, National Institute for Interdisciplinary Science and Technology (NIIST), Trivandrum 695019 (India); Prabhakar Rao, P., E-mail: padala_rao@yahoo.com [Materials and Minerals Division, National Institute for Interdisciplinary Science and Technology (NIIST), Trivandrum 695019 (India); Radhakrishnan, A.N.; Sibi, K.S.; Koshy, Peter [Materials and Minerals Division, National Institute for Interdisciplinary Science and Technology (NIIST), Trivandrum 695019 (India)

2009-07-01

A new series of pyrochlore type ceramic semiconducting oxides in Ca-Ce-Ti-M-O (M = Nb or Ta) system has been synthesized by the conventional ceramic route. The electrical conductivity measurements show that these oxides exhibit semiconducting behavior and the conductivity increases with the Ce content in the compound. Activation energy of the current carriers is in the range of 0.5-1.6 eV. The electrical conductivity in these oxides is due to the presence of Ce{sup 3+}, which remains in the reduced state without being oxidized to Ce{sup 4+} by structural stabilization. The photoluminescence and X-ray photoelectron spectroscopy analysis corroborate the presence of Ce in the 3+ state. Impedance spectral analysis is carried out to evaluate the transport properties and indicates that the conduction in these compounds is mainly due to electronic contribution. The X-ray powder diffraction and Raman spectroscopy analysis establishes that these oxides belong to a cubic pyrochlore type structure.

Superconductivity of Ta{sub 34}Nb{sub 33}Hf{sub 8}Zr{sub 14}Ti{sub 11} high entropy alloy from first principles calculations

Energy Technology Data Exchange (ETDEWEB)

Jasiewicz, K.; Wiendlocha, B.; Korben, P.; Kaprzyk, S.; Tobola, J. [AGH University of Science and Technology, Faculty of Physics and Applied Computer Science, Al. Mickiewicza 30, 30-059, Krakow (Poland)

2016-05-15

The Korringa-Kohn-Rostoker method with the coherent potential approximation (KKR-CPA) is applied to study the first superconducting high entropy alloy (HEA) Ta{sub 34}Nb{sub 33}Hf{sub 8}Zr{sub 14}Ti{sub 11} (discovered in 2014 with T{sub c}=7.3 K), focusing on estimations of the electron-phonon coupling constant λ. The electronic part of λ has been calculated using the rigid muffin-tin approximation (RMTA), while the phonon part has been approximated using average atomic mass and experimental Debye temperature. The estimated λ=1.16 is close to the value determined from specific heat measurements, λ=0.98, and suggests rather strong electron-phonon coupling in this material. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Surface microstructures and corrosion resistance of Ni-Ti-Nb shape memory thin films

Energy Technology Data Exchange (ETDEWEB)

Li, Kun [School of Materials Science and Engineering, Beihang University, Beijing 100191 (China); Beijing Key Laboratory for Advanced Functional Materials and Thin Film Technology, Beihang University, Beijing 100191 (China); Faculty of Engineering and Environment, Northumbria University, Newcastle Upon Tyne NE1 8ST (United Kingdom); Li, Yan, E-mail: liyan@buaa.edu.cn [School of Materials Science and Engineering, Beihang University, Beijing 100191 (China); Beijing Key Laboratory for Advanced Functional Materials and Thin Film Technology, Beihang University, Beijing 100191 (China); Huang, Xu [Memry Corporation, Bethel, CT 06801 (United States); Gibson, Des [Institute of Thin Films, Sensors & Imaging, Scottish Universities Physics Alliance, University of the West of Scotland, Paisley PA1 2BE (United Kingdom); Zheng, Yang; Liu, Jiao; Sun, Lu [School of Materials Science and Engineering, Beihang University, Beijing 100191 (China); Beijing Key Laboratory for Advanced Functional Materials and Thin Film Technology, Beihang University, Beijing 100191 (China); Fu, Yong Qing, E-mail: richard.fu@northumbria.ac.uk [Faculty of Engineering and Environment, Northumbria University, Newcastle Upon Tyne NE1 8ST (United Kingdom)

2017-08-31

Highlights: • The corrosion resistance of Ni-Ti-Nb shape memory thin films is investigated. • Modified surface oxide layers improve the corrosion resistance of Ni-Ti-Nb films. • Further Nb additions reduce the potential corrosion tendency of the films. - Abstract: Ni-Ti-Nb and Ni-Ti shape memory thin films were sputter-deposited onto silicon substrates and annealed at 600 °C for crystallization. X-ray diffraction (XRD) measurements indicated that all of the annealed Ni-Ti-Nb films were composed of crystalline Ni-Ti (Nb) and Nb-rich grains. X-ray photoelectron spectroscopy (XPS) tests showed that the surfaces of Ni-Ti-Nb films were covered with Ti oxides, NiO and Nb{sub 2}O{sub 5}. The corrosion resistance of the Ni-Ti-Nb films in 3.5 wt.% NaCl solution was investigated using electrochemical tests such as open-circuit potential (OCP) and potentio-dynamic polarization tests. Ni-Ti-Nb films showed higher OCPs, higher corrosion potentials (E{sub corr}) and lower corrosion current densities (i{sub corr}) than the binary Ni-Ti film, which indicated a better corrosion resistance. The reason may be that Nb additions modified the passive layer on the film surface. The OCPs of Ni-Ti-Nb films increased with further Nb additions, whereas no apparent difference of E{sub corr} and i{sub corr} was found among the Ni-Ti-Nb films.

Photocatalytic activity of TiO2/Nb2O5/PANI and TiO2/Nb2O5/RGO as new nanocomposites for degradation of organic pollutants.

Science.gov (United States)

Zarrin, Saviz; Heshmatpour, Felora

2018-06-05

In this study, highly active titanium dioxide modified by niobium oxide (Nb 2 O 5 ), polymer (PANI) and reduced graphene oxide (RGO) were successfully prepared. The morphology, structure, surface area and light absorption properties of the present nanocomposites for removal of methylene blue (MB) and methyl orange (MO) were investigated and compared with those of TiO 2 /Nb 2 O 5 and TiO 2 nanoparticles. The characterization techniques such as XRD, FT-IR, UV-vis, SEM, EDX, BET and TEM were employed in order to identify the nanocomposites. Also, photocatalytic properties of TiO 2 /Nb 2 O 5 /PANI and TiO 2 /Nb 2 O 5 /RGO nanocomposites under visible light irradiation were studied. In this way, the obtained results were compared to each other and also compared to TiO 2 /Nb 2 O 5 and TiO 2 nanoparticles. In this context, the chemical oxygen demand (COD) removal follows the photodegradation in observed performance. The results indicate that reduced TiO 2 /Nb 2 O 5 nanocomposite is effectively modified by graphene oxide to give TiO 2 /Nb 2 O 5 /RGO composite. The TiO 2 /Nb 2 O 5 /RGO exhibits significantly higher photocatalytic activity in degradation of organic dyes under visible light rather than that of TiO 2 /Nb 2 O 5 /PANI, TiO 2 /Nb 2 O 5 and pure TiO 2 . Copyright © 2018 Elsevier B.V. All rights reserved.

New ternary tantalum borides containing boron dumbbells: Experimental and theoretical studies of Ta2OsB2 and TaRuB

International Nuclear Information System (INIS)

Mbarki, Mohammed; Touzani, Rachid St.; Rehorn, Christian W.G.; Gladisch, Fabian C.; Fokwa, Boniface P.T.

2016-01-01

The new ternary transition metal-rich borides Ta 2 OsB 2 and TaRuB have been successfully synthesized by arc-melting the elements in a water-cooled crucible under an argon atmosphere. The crystal structures of both compounds were solved by single-crystal X-ray diffraction and their metal compositions were confirmed by EDX analysis. It was found that Ta 2 OsB 2 and TaRuB crystallize in the tetragonal Nb 2 OsB 2 (space group P4/mnc, no. 128) and the orthorhombic NbRuB (space group Pmma, no. 51) structure types with lattice parameters a=5.878(2) Å, c=6.857(2) Å and a=10.806(2) Å, b=3.196(1) Å, c=6.312(2) Å, respectively. Furthermore, crystallographic, electronic and bonding characteristics have been studied by density functional theory (DFT). Electronic structure relaxation has confirmed the crystallographic parameters while COHP bonding analysis indicates that B 2 -dummbells are the strongest bonds in both compounds. Moreover, the formation of osmium dumbbells in Ta 2 OsB 2 through a Peierls distortion along the c-axis, is found to be the origin of superstructure formation. Magnetic susceptibility measurements reveal that the two phases are Pauli paramagnets, thus confirming the theoretical DOS prediction of metallic character. Also hints of superconductivity are found in the two phases, however lack of single phase samples has prevented confirmation. Furthermore, the thermodynamic stability of the two modifications of AMB (A=Nb, Ta; M =Ru, Os) are studied using DFT, as new possible phases containing either B 4 - or B 2 -units are predicted, the former being the most thermodynamically stable modification. - Graphical abstract: The two new ternary tantalum borides, Ta 2 OsB 2 and TaRuB, have been discovered. Their crystal structures contain boron dumbbells, which are the strongest bonds. Peirls distortion is found responsible for Os 2 -dumbbells formation in Ta 2 OsB 2 . Ta 2 OsB 2 and TaRuB are Pauli paramagnet and potential superconductors. - Highlights: �

Nanotubular surface and morphology of Ti-binary and Ti-ternary alloys for biocompatibility

International Nuclear Information System (INIS)

Choe, Han-Cheol

2011-01-01

The nanotubular surface of Ti-binary and Ti-ternary alloys for biomaterials has been investigated using various methods of surface characterization. Binary Ti-xNb (x = 10, 20, 30, and 40 wt.%) and ternary Ti-30Ta-xNb (x = 3, 7 and 15 wt.%) alloys were prepared by using the high-purity sponges; Ti, Ta and Zr spheres. The nanotube on the alloy surface was formed in 1.0 M H 3 PO 4 with small additions of NaF (0.5 and 0.8 wt.%), using a potentiostat. For cell proliferation, an MC3T3-E1 mouse osteoblast was used. The surface characteristics were investigated using field-emission scanning electron microscope, energy dispersive spectroscopy, and X-ray photoelectron spectroscopy. Binary Ti-xZr alloys had a lamellar and a needle-like structure, whereas, ternary Ti-30Ta-xZr alloys had equiaxed grains with a lamellar martensitic α' structure. The thickness of the needle-like laths of the α-phase increased as the Zr content increased. The nanotubes formed on the α phase and β phase showed a different size and shape appearance with Zr content. As the Zr content increased from 3 to 40 wt.%, the diameter of the nanotubes in Ti-xZr and Ti-30Ta-xZr alloy decreased from 200 nm to 50 nm. The nanotubular Ti-30Ta-15Zr alloy surface with a diameter of 50 nm provided a good osseointegration; cell proliferation, migration and differentiation.

A nano lamella NbTi–NiTi composite with high strength

Energy Technology Data Exchange (ETDEWEB)

Jiang, Jiang [Jiangxi Key Laboratory of Advanced Copper and Tungsten Materials, Jiangxi Academy of Sciences, Nanchang 330029 (China); Institute of Applied Physics of Jiangxi Academy of Sciences, Nanchang 330029 (China); State Key Laboratory of Heavy Oil Processing and Department of Materials Science and engineering, China University of Petroleum, Beijing 102249 (China); Jiang, Daqiang [State Key Laboratory of Heavy Oil Processing and Department of Materials Science and engineering, China University of Petroleum, Beijing 102249 (China); School of Mechanical and Chemical Engineering, The University of Western Australia, WA 6009 (Australia); Hao, Shijie; Yu, Cun; Zhang, Junsong [State Key Laboratory of Heavy Oil Processing and Department of Materials Science and engineering, China University of Petroleum, Beijing 102249 (China); Ren, Yang [X-ray Science Division, Argonne National Laboratory, Argonne, IL 60439 (United States); Lu, Deping; Xie, Shifang [Jiangxi Key Laboratory of Advanced Copper and Tungsten Materials, Jiangxi Academy of Sciences, Nanchang 330029 (China); Institute of Applied Physics of Jiangxi Academy of Sciences, Nanchang 330029 (China); Cui, Lishan, E-mail: lishancui63@126.com [State Key Laboratory of Heavy Oil Processing and Department of Materials Science and engineering, China University of Petroleum, Beijing 102249 (China)

2015-05-01

A hypereutectic Nb{sub 60}Ti{sub 24}Ni{sub 16} (at%) alloy was prepared by vacuum induction melting, and a nano lamellae NbTi–NiTi composite was obtained by hot-forging and wire-drawing of the ingot. Microscopic analysis showed that NbTi and NiTi nano lamellae distributed alternatively in the composite, and aligned along the wire axial direction, with a high volume fraction (~70%) of NbTi nano lamellae. In situ synchrotron X-ray diffraction analysis revealed that stress induced martensitic transformation occurred upon loading, which would effectively weaken the stress concentration at the interface and avoid the introduction of defects into the nano reinforced phase. Then the embedded NbTi nano lamellae exhibited a high elastic strain up to 2.72%, 1.5 times as high as that of the Nb nanowires embedded in a conventional plastic matrix, and the corresponding stress carried by NbTi was evaluated as 2.53 GPa. The high volume fraction of NbTi nano lamellae improved the translation of high strength from the nano reinforced phase into bulk properties of the composite, with a platform stress of ~1.7 GPa and a fracture strength of ~1.9 GPa.

Proximity Effect Transfer from NbTi into a Semiconductor Heterostructure via Epitaxial Aluminum

DEFF Research Database (Denmark)

Drachmann, A C C; Suominen, H J; Kjærgaard, Morten

2017-01-01

We demonstrate the transfer of the superconducting properties of NbTi, a large-gap high-critical-field superconductor, into an InAs heterostructure via a thin intermediate layer of epitaxial Al. Two device geometries, a Josephson junction and a gate-defined quantum point contact, are used...... to characterize interface transparency and the two-step proximity effect. In the Josephson junction, multiple Andreev reflections reveal near-unity transparency with an induced gap Δ* = 0.50 meV and a critical temperature of 7.8 K. Tunneling spectroscopy yields a hard induced gap in the InAs adjacent...

Interplay between lattice distortions, vibrations and phase stability in NbMoTaW high entropy alloys

NARCIS (Netherlands)

Kormann, F.H.W.; Sluiter, M.H.F.

2016-01-01

Refractory high entropy alloys (HEA), such as BCC NbMoTaW, represent a promising materials class for next-generation high-temperature applications, due to their extraordinary mechanical properties. A characteristic feature of HEAs is the formation of single-phase solid solutions. For BCC NbMoTaW,

Effect of Zr substitution on the thermal and mechanical properties of Rh3A (A=Nb,Ta) - A theoretical study

Science.gov (United States)

Manjula, M.; Sundareswari, M.; Viswanathan, E.

2018-04-01

The present study focuses upon the thermal and mechanical properties of Rh3ZrxA1-x (A= Nb,Ta) ternary alloys using ab initio density functional theory where Nb/Ta is substituted by Zr. These ternary alloys were investigated for the first time using elastic moduli, hardness, Debye temperature, Debye average velocity and Gruneisen parameter. Further the ductile/brittle analysis was made by using Cauchy pressure, degree of brittleness and Poisson's ratio. Systematic addition of Zr with Rh3Nb/Ta shows that Rh3Zr0.75Nb0.25, Rh3Zr0.875Nb0.125 and Rh3Zr0.875Ta0.125combinations are more ductile. Further the melting temperature of Rh3Zr0.75Nb0.25(2227 K), Rh3Zr0.875Nb0.125(2200 K) and Rh3Zr0.875Ta0.125 (2134 K) alloys are nearer to those of their parent binary alloys namely Rh3Nb (2636 K) and Rh3Ta (2562 K). Their corresponding density values (10.84 gm/cm3, 10.77 gm/cm3 and 11.09 gm/cm3) are found to be much less than those of their parent materials.

A Nb3Sn high field dipole

International Nuclear Information System (INIS)

McClusky, R.; Robins, K.E.; Sampson, W.B.

1990-01-01

A dipole magnet approximately 1 meter long with an 8 cm bore has been fabricated from cable made from Nb 3 Sn multifilamentary strands. The coil consists of four layers of conductor wound in pairs to eliminate internal joints. Each set of layers is separately constrained with Kevlar-epoxy bands and the complete assembly clamped in a split laminated iron yoke. The inner coil pairs were wound before heat treating while the outer coils were formed from pre-reacted cable using conventional insulation. A NbTi version of the magnet was fabricated using SSC version of the magnet was fabricated using SSC conductor to test the construction techniques. This magnet reached a maximum central field of 7.6 Tesla, at 4.4K which is very close to the limit estimated from conductor measurements. The Nb 3 Sn magnet, however, only reached a maximum field at 8.1T considerably short of the field expected from measurements on the inner cable. 7 refs., 5 figs

Fabrication and testing of the Nb3Sn superconductor for High-Field Test Facility (HFTF)

International Nuclear Information System (INIS)

Spencer, C.; Adam, E.; Gregory, E.; Marancik, W.; Sanger, P.; Scanlan, R.; Cornish, D.

1979-01-01

A 5000 A-12 T fully stable Nb 3 Sn superconductor has to be produced for the insert magnet of the high-field test facility being built at Lawrence Livermore Laboratory. A process is described which permits the fabrication of long lengths of large fully transposed monolithic superconductors containing in excess of 100,000 filaments of Nb 3 Sn. Measurements of critical current as a function of magnetic field and longitudinal strain on prototype samples are reported

ADHESION OF BIOCOMPATIBLE TiNb COATING

Directory of Open Access Journals (Sweden)

Tomas Kolegar

2017-06-01

Full Text Available Preparation of a coating with a high quality requires good adhesion of the film to the substrate. The paper deals with the adhesion of biocompatible TiNb coating with different base materials. Several materials such as titanium CP grade 2, titanium alloys Ti6Al4V and stainless steel AISI 316L were measured. Testing samples were made in the shape of small discs. Those samples were coated with a TiNb layer by using the PVD method (magnetron sputtering. Onto the measured layer of TiNb an assistant cylinder was stuck using a high strength epoxy adhesive E1100S. The sample with the assistant cylinder was fixed into a special fixture and the whole assembly underwent pull-off testing for adhesion. The main result of this experiment was determining the strength needed to peel the layer and morphology and size of the breakaway. As a result, we will be able to determine the best base material and conditions where the coating will be remain intact with the base material.

Mesoporous Nb and Ta Oxides: Synthesis, Characterization and Applications in Heterogeneous Acid Catalysis

Science.gov (United States)

Rao, Yuxiang Tony

In this work, a series of mesoporous Niobium and Tantalum oxides with different pore sizes (C6, C12, C18 , ranging from 12A to 30 A) were synthesized using the ligand-assisted templating approach and investigated for their activities in a wide range of catalytic applications including benzylation, alkylation and isomerization. The as-synthesized mesoporous materials were characterized by nitrogen adsorption, powder X-ray diffraction, transmission electron microscopy (TEM), scanning electron microscopy (SEM), thermo gravimetric analysis (TGA), differential scanning calorimetry (DSC), and solid-state Nuclear magnetic resonance (NMR) techniques. In order to probe into the structural and coordination geometry of mesoporous Nb oxide and in efforts to make meaningful comparisons of mesoporous niobia prepared by the amine-templating method with the corresponding bulk sol-gel prepared Nb2O5 phase, 17O magic-angle-spinning solid-state NMR studies were conducted. The results showed a very high local order in the mesoporous sample. The oxygen atoms are coordinated only as ONb 2 in contrast with bulk phases in which the oxygen atoms are always present in a mixture of ONb2 and ONb3 coordination environments. To enhance their surface acidities and thus improve their performance as solid acid catalysts in the acid-catalyzed reactions mentioned above, pure mesoporous Nb and Ta oxides were further treated with 1M sulfuric acid or phosphoric acid. Their surface acidities before and after acid treatment were measured by Fourier transform infraRed (FT IR), amine titration and temperature programmed desorption of ammonia (NH3-TPD). Results obtained in this study showed that sulfated mesoporous Nb and Ta oxides materials possess relative high surface areas (up to 612 m 2/g) and amorphous wormhole structure. These mesoporous structures are thus quite stable to acid treatment. It was also found that Bronsted (1540 cm-1) and Lewis (1450 cm-1) acid sites coexist in a roughly 50:50 mixture

Current-ripple effect on superconductive dc critical current measurements

International Nuclear Information System (INIS)

Goodrich, L.F.; Bray, S.L.; Clark, A.F.

1988-01-01

The effect of sample-current power-supply ripple on dc critical current measurement in multifilamentary NbTi superconductors was evaluated. In general the ripple in a current supply became more significant above 500 A because effective filtering was hard to achieve. Ripple also caused noise at the input of the voltmeter used for the measurements. The quantitative effect of current ripple was studied using a battery current supply modified to allow the creation of ripple current with variable frequency and amplitude. Problems common to all large-conductor critical current measurements are discussed

Photoluminescent properties of Pr3+ doped YTiAO6 (A= Nb&Ta) euxenite compounds

Science.gov (United States)

Venugopal, Meenu; Kumar, H. Padma

2018-04-01

Pr3+ doped YTiAO6 (A = Nb and Ta) compounds were prepared by conventional solid state ceramic route. X - ray diffraction studies of the samples confirmed the euxenite orthorhombic phase formation. Effect of Pr3+ doping on the optical and luminescence properties of YTiAO6 (A = Nb and Ta) were studied. The strong absorption in the UV region are due to the absorption by the host YTiAO6 (A = Nb and Ta) and all other peaks can be attributed to that of Pr3+. Host emission peaks are observed around 485 nm and 460 nm in all samples. The red emission observed at 614 nm in the doped samples corresponds to the 1D2 to 3H4 transition of Pr3+ ion. CIE colour coordinates and chromaticity values were also discussed.

Carbide precipitation kinetics in austenite of a Nb-Ti-V microalloyed steel

International Nuclear Information System (INIS)

Jung, Jae-Gil; Park, June-Soo; Kim, Jiyoung; Lee, Young-Kook

2011-01-01

Highlights: → Carbide precipitation kinetic was fastest at 950 deg. C and accelerated by strain. → Nucleation sites for (Nb,Ti)C above 950 deg. C were mainly undissolved (Ti,Nb)(C,N). → Strain enabled (Nb,Ti)C to nucleate on all sides of (Ti,Nb)(C,N) above 950 deg. C. → Strain changed nucleation sites from (Ti,Nb)(C,N) to dislocations below 900 deg. C. → Strain also accelerated the change in particle composition to equilibrium one. - Abstract: The isothermal precipitation kinetics of carbides in both strain-free and strained austenite (γ) of a microalloyed steel were quantitatively investigated through the electrical resistivity and transmission electron microscopy. The (Nb,Ti)C carbides at the interfaces of the undissolved (Ti,Nb)(C,N) carbonitrides were observed at all temperatures in strain-free γ. However, for strain-induced precipitation, above 950 deg. C, the precipitation of (Nb,Ti)C carbides near the undissolved (Ti,Nb)(C,N) carbonitrides was predominant due to the recrystallization of strained γ. Meanwhile, the fine (Nb,Ti,V)C carbides were homogeneously precipitated in non-recrystallized γ at 850 deg. C and 900 deg. C, as well as near the undissolved (Ti,Nb)(C,N) particles. The electrical resistivity method was successfully used to quantitatively measure the isothermal precipitation kinetics of carbides in both strain-free and strained γ. The precipitation-time-temperature diagrams of the carbide in strain-free and strained γ, with nose temperatures of 950 deg. C, were generated and the precipitation kinetics were greatly accelerated by the applied strain.

The superconductor revolutions and the (slow) applications evolution

International Nuclear Information System (INIS)

Foner, S.

1990-01-01

The discovery in the 1960's of type 2 superconductors with high critical current densities in high magnetic fields (and the development of NbTi in particular) led to the first revolution. The discovery of high temperature superconductors (HTS) started the second revolution. At this stage ceramists became involved with superconductors. I will assess the status of various superconductor applications, progress of HTS and their possible applications at 4.2K, and near-term needs for superconducting materials operating at 30T in specialized facilities. Reasons for the slow growth of superconductor applications will be reviewed

Superconducting properties of (Nb,Ta)3Sn wires fabricated by the bronze process

International Nuclear Information System (INIS)

Suenaga, M.; Aihara, K.; Kaiho, K.; Luhman, T.S.

1979-01-01

Measurements of the superconducting critical temperature T/sub c/, critical current density, J/sub c/ (8 3 Sn monofilamentary wires. Ta content in the Nb 3 Sn compound was varied by alloying the Nb core prior to a reaction heat treatment. Core compositions were 0, 3, 7, 10, and 20 wt% Ta and heat treatments for the reaction were 16, 64, and 120 h at 725 0 C. For the 120 h heat treatment T/sub c/ decreased monotonically with Ta content from 17.5 to 15.7K while H/sub c2/ increased from 19.8 to 24.6 T. With increasing Ta content J/sub c/ (16 T) increased from 0.7 x 10 5 A/cm 2 to a maximum value of 1.3 x 10 5 at 7 wt% Ta. Further increases in the Ta content produced a decrease in J/sub c/(16 T). At 10 T J/sub c/ decreased with increasing Ta content. An important aspect of this work is the observation that alloying with Ta did not hinder wire ductility during drawing. It appears therefore that the improvements in J/sub c/(16 T) can be incorporated into commercially manufactured conductors

Recent status of superconductors for accelerator magnets

International Nuclear Information System (INIS)

Greene, A.F.

1992-01-01

A survey is given of superconductor wire and cable which has been or will be used for construction of dipole magnets for all of the large European and US superconducting accelerator rings. Included is a simplified view of the construction methods and operating requirements of an accelerator dipole magnet, with emphasis on required superconductor performance. The methods of fabricating Nb-Ti superconductors are described, including the critical parameters and materials requirements. The superconductor performance requirements are summarized in an effort to relate why these are important to accelerator designers. Some of the recently observed time dependent effects are covered briefly

Superconductors with low critical temperature for electro-magnets

International Nuclear Information System (INIS)

Devred, A.

2002-07-01

Among the superconductors with low critical temperature that are used to build magnets, NbTi has reached a development state that allows a massive production for big equipment of physics and an industrial production in the domain of medicine imaging. The material that might challenge the supremacy of NbTi is Nb 3 Sn but some technical difficulties have yet to be overcome. This report begins with a review of the different industrial processes used to produce superconducting wires based on the NbTi and Nb 3 Sn materials. The transition from the superconducting state to the resistive normal state is described for both materials, the magnetizing of multi-wire superconducting cables is also presented. The author details the different patterns of wires in cables and proposes a formulary that allows the determination, in some simple cases,of energy losses that are generated in a superconducting cable by a variable magnetic field. (A.C.)

Experimental Determination of Impurity and Interdiffusion Coefficients in Seven Ti and Zr Binary Systems Using Diffusion Multiples

Science.gov (United States)

Chen, Zhangqi; Liu, Zi-Kui; Zhao, Ji-Cheng

2018-05-01

Diffusion coefficients of seven binary systems (Ti-Mo, Ti-Nb, Ti-Ta, Ti-Zr, Zr-Mo, Zr-Nb, and Zr-Ta) at 1200 °C, 1000 °C, and 800 °C were experimentally determined using three Ti-Mo-Nb-Ta-Zr diffusion multiples. Electron probe microanalysis (EPMA) was performed to collect concentration profiles at the binary diffusion regions. Forward simulation analysis (FSA) was then applied to extract both impurity and interdiffusion coefficients in Ti-rich and Zr-rich part of the bcc phase. Excellent agreements between our results and most of the literature data validate the high-throughput approach combining FSA with diffusion multiples to obtain a large amount of systematic diffusion data, which will help establish the diffusion (mobility) databases for the design and development of biomedical and structural Ti alloys.

Fabrication of Nb{sub 3}Al superconductor by the optimized mechanical alloying method with low temperature

Energy Technology Data Exchange (ETDEWEB)

Zhang, Y., E-mail: yongzhang@swjtu.cn [Key Laboratory of Magnetic Levitation Technologies and Maglev Trains, Ministry of Education of China, and Superconductivity and New Energy R& D Center, Southwest Jiaotong University, Chengdu 610031 (China); Lin, W.J.; Xu, L.Y.; Yang, D.W.; Chen, Y.L. [Key Laboratory of Magnetic Levitation Technologies and Maglev Trains, Ministry of Education of China, and Superconductivity and New Energy R& D Center, Southwest Jiaotong University, Chengdu 610031 (China); Li, P.Y.; Pan, X.F.; Yan, G. [Western Superconducting Technoligies Co., Ltd., Xi' an 710018 (China); Zhao, Y., E-mail: yzhao@home.swjtu.edu.cn [Key Laboratory of Magnetic Levitation Technologies and Maglev Trains, Ministry of Education of China, and Superconductivity and New Energy R& D Center, Southwest Jiaotong University, Chengdu 610031 (China); School of Materials Science and Engineering, University of New South Wales, Sydney 2052 NSW (Australia)

2016-11-15

Highlights: • Due to a much better strain tolerance than Nb{sub 3}Sn, Nb{sub 3}Al has been considered as an excellent candidate for making high field magnets. At present, the Nb{sub 3}Al superconducting wires were prepared mainly by the Jelly-roll method combined with a rapid heating and quenching (RHQ) heat treatment at around 2000 °C. In this study, Nb{sub 3}Al superconductor with T{sub c} of 15.6 K is directly prepared with a mechanical alloying method followed by a low temperature annealing at 800 to 900 °C. Our results hint the possibility that Nb{sub 3}Al superconducting wire with high performance can be prepared below the melting point of Cu (1080 °C) by a conventional powder in tube (PIT) method, thus effectively avoiding high temperature heat treatment and RHQ device. - Abstract: Mechanical alloying was used to synthesize Nb{sub 3}Al superconductor successfully, and the process was optimization under various preparation conditions. In the current study, Nb{sub 3}Al superconductor with T{sub c} of 15.6 K was directly prepared from high quality Nb (Al) solid solution by mechanical alloying method and heat treatment at a low temperature of 800 to 900 °C. The results showed that Nb{sub 3}Al superconducting wire with high performance could be prepared after heat treatment below the melting point of Cu (1080°C) and using Nb (Al) solid solution and conventional powder in tube (PIT) method, thus effectively avoiding ultra-high temperature heat treatment and special rapid heating and quenching(RHQ) device.

A study on the microstructural property and thermal property of Ti-alloys without Al as biomaterials

International Nuclear Information System (INIS)

Ban, Jae Sam; Lee, Kyung Won; Cho, Kyu Zong; Kim, Sun Jin

2008-01-01

Ti-10Ta-10Nb alloys were designed for surgical implants, dental and orthopedic materials without V and Al. Specimens of the Ti-10Ta-10Nb alloy were remelted three times through the consumable VAR process and were made into small rods. Homogenization heat treatment was carried out for 24 hours under a vacuum of 10 -3 torr and at constant temperature of 1050 .deg. C and then the specimens were cooled in water. After that, we observed the microstructure of the alloy by using an SEM. Rockwell (B) hardness, thermal expansion coefficient and specific heat of the Ti-10Ta-10Nb alloy were measured in order to examine the material properties. It was found that the mechanical property of the specimen was altered by the heat treatment, and thermal expansion coefficient and specific heat of the Ti-10Ta-10Nb alloy would be useful data for engineering processing design

Solubilization and precipitation of ω and α phases in Ti-30 Nb and Ti-35 Nb alloys

International Nuclear Information System (INIS)

Hayama, A.O.F.; Lopes, J.F.S.C.; Caram, R.

2010-01-01

This work presents the main results of the characterization of Ti-30Nb and Ti-35Nb alloys (wt%) submitted to the solutioning heat treatment following by aging. Samples were obtained by electric arc melting, followed by solution heat treatment at 1000 deg C during 8 hours and cooling in water, the microstructure obtained is formed by β and α phases. Samples were aged at 260 and 400 deg C during periods of time varying from 1 to 240 min. Characterization was performed using light optical microscopy, X-ray diffraction, Young's modulus measurements by acoustic emission and Vickers hardness. The results show the presence of β and α ' ' phases in samples of the Ti-30Nb alloy aged at 260 deg C. In samples aged at 400 deg C, precipitation of ω and α ' ' phases took place, and due to this fact, an increase in Young's modulus and in hardness occurred. (author)

Topotactic dehydration of the lamellar oxide HK2Ti5NbO14 x H2O: the oxide K4Ti10Nb2O27

International Nuclear Information System (INIS)

Grandin, A.; Borel, M.M.; Hervieu, M.; Raveau, B.

1987-01-01

The lamellar oxide HK 2 Ti 5 NbO 14 x H 2 O can be topotactically dehydrated to K 4 Ti 10 Nb 2 O 27 . Electron diffraction and X-ray diffraction studies of this phase lead to a monoclinic cell with the parameters a = 17.005, b = 3.78, c = 9.01 A and β 92.14 0 . Diffusion streaks on the electron diffraction patterns indicate disorder whereas the existence of two sets of lattices on the same crystal give evidence of the topotactic character of the reaction. A structural model is proposed for K 4 Ti 10 Nb 2 O 27 , which corresponds to the intergrowth of K 3 TiNbO 14 layers with the K 2 Ti 6 O 13 tunnel structure. The possibility of formation of various intergrowths such as (KTi 5 NbO 13 )/sub n/ (HK 2 Ti 5 NbO 14 )/sub n/' is suggested

MAXIMSUPER: a computer program to assist in the design of multifilamentary superconducting composites

International Nuclear Information System (INIS)

Hoard, R.W.; Scanlan, R.M.; Hirzel, D.G.

1979-01-01

The strain degradation of critical current density has been analytically and experimentally investigated for multifilamentary superconducting composites produced in a bronze core geometry. Analytic results were obtained from a computer program (MAXIMSUPER) which predicts the stresses and strains in composites as a result of thermal and axial loading. Tensile test data for Nb 3 Sn are described. It is believed that the strain dependence of the critical current found in Nb 3 Sn is due to strain enhanced martensitic transformation

Technology development of fabrication NbTi and Nb3 Sn superconducting wires

International Nuclear Information System (INIS)

Rodrigues Junior, D.; Bormio, C.; Baldan, C.A.; Ramos, M.J.; Pinatti, D.G.

1988-01-01

The technology development of NbTi and Nb 3 Sn superconducting wires are studied, mentioning the use of fluxes capture theory in the sizing of wires fabrication. The fabrication process, the thermal treatment and the experimental datas of critical temperature and current of Nb 3 Sn wires are described. (C.G.C.) [pt

Influence of cold rolling and ageing treatment on microstructure and mechanical properties of Ti-30Nb-5Ta-6Zr alloy.

Science.gov (United States)

Wang, Yu; Zhao, Juan; Dai, Shijuan; Chen, Feng; Yu, Xinquan; Zhang, Youfa

2013-11-01

In this study, the relationship between deformation mechanism and rolling reductions was investigated, and the effects of deformation reductions on the microstructure and mechanical properties of the alloys both cold rolled and aged were revealed. It was found that the equiaxed β grains of the Ti-30Nb-5Ta-6Zr alloy have elongated gradually with increasing the deformation reduction. The deformation mechanism of dislocation slipping, deformed twins and SIM α″ phase appeared in the alloy deformed by 23% and 66%. The type of twins of the alloy deformed by 23% and 66% are {112}〈111〉 and {332}〈113〉 respectively. When the reduction was up to 85%, dislocation slipping was the main mode of deformation accompanying with SIM α″ phase occurred. With increasing deformation reduction, the average size of lenticular precipitation α phase decreased gradually. The strength of cold rolled and aged samples increased with increasing deformation reduction, while elastic modulus decreased. Due to the precipitation α phase, the elastic modulus of aged samples was higher than cold rolled. © 2013 Elsevier Ltd. All rights reserved.

Enhanced carrier density in Nb-doped SrTiO3 thermoelectrics

KAUST Repository

Ozdogan, K.

2012-03-08

We study epitaxial SrTiO3 interfaced with Nb-doped SrTi1-x Nb x O3 (x = 0, 0.125, 0.25, 0.375, and 0.5) by full-potential density functional theory. From the electronic band structures obtained by our ab-initio calculations we determine the dependence of the induced metallicity on the Nb concentration. We obtain a monotonous increase of the carrier density with the Nb concentration. The results are confirmed by experiments for SrTi0.88Nb0.12O3 and SrTi0.8Nb0.2O3, demonstrating the predictive power and limitations of our theoretical approach. We also show that the Seebeck coefficient decreases monotonously with increasing temperature.

Enhanced carrier density in Nb-doped SrTiO3 thermoelectrics

KAUST Repository

Ozdogan, K.; Upadhyay Kahaly, M.; Sarath Kumar, S. R.; Alshareef, Husam N.; Schwingenschlö gl, Udo

2012-01-01

We study epitaxial SrTiO3 interfaced with Nb-doped SrTi1-x Nb x O3 (x = 0, 0.125, 0.25, 0.375, and 0.5) by full-potential density functional theory. From the electronic band structures obtained by our ab-initio calculations we determine the dependence of the induced metallicity on the Nb concentration. We obtain a monotonous increase of the carrier density with the Nb concentration. The results are confirmed by experiments for SrTi0.88Nb0.12O3 and SrTi0.8Nb0.2O3, demonstrating the predictive power and limitations of our theoretical approach. We also show that the Seebeck coefficient decreases monotonously with increasing temperature.

Radiation Limits for Nb3Sn Superconductors for ITER Magnets: A literature review

International Nuclear Information System (INIS)

Simon, N.J.

1995-01-01

The data base on radiation damage to Nb 3 Sn superconductors is compiled from the literature and assessed in this report. Nb 3 Sn superconductors are currently under procurement for use in ITER magnet prototypes. In contrast to the data base on insulation materials proposed for use in ITER magnets, the data base on the radiation damage of Nb 3 Sn is much more complete. Key results have often been confirmed by several groups at different institutions. The investigation of variables that influence radiation damage has also been much more complete for Nb 3 Sn than for insulators. Furthermore, in situ testing of superconducting parameters is much easier than in situ mechanical testing of insulators, and in situ testing has invariably been performed after cryogenic irradiation of Nb 3 Sn. However, in recent years, Nb 3 Sn testing has also suffered from the lack of 4-K irradiation facilities. Just as new processing methods to obtain more economical Nb 3 Sn conductor products in large quantity were being developed, cryogenic irradiation sources were being phased out. Therefore, this brief introductory section presents some basic information on the properties and structure of Nb 3 Sn superconducting composites and the distinctions between different fabrication processes. This provides a background to assess the adequacy of the current cryogenic data base on radiation damage, Also, since synergistic effects of strain and irradiation have recently been investigated, a brief discussion of the effects of strain on Nb 3 Sn properties is included in this introduction

Structure and mechanical properties of as-cast Ti-5Nb-xFe alloys

International Nuclear Information System (INIS)

Hsu, Hsueh-Chuan; Hsu, Shih-Kuang; Wu, Shih-Ching; Lee, Chih-Jhan; Ho, Wen-Fu

2010-01-01

In this study, as-cast Ti-5Nb and a series of Ti-5Nb-xFe alloys were investigated and compared with commercially pure titanium (c.p. Ti) in order to determine their structure and mechanical properties. The series of Ti-5Nb-xFe alloys contained an iron content ranging from 1 to 5 mass% and were prepared by using a commercial arc-melting vacuum-pressure casting system. Additionally, X-ray diffraction (XRD) for phase analysis was conducted with a diffractometer, and three-point bending tests were performed to evaluate the mechanical properties of all specimens. The fractured surfaces were observed by using scanning electron microscopy (SEM). The experimental results indicated that these alloys possessed a range of different structures and mechanical properties dependent upon the various additions of Fe. With an addition of 1 mass% Fe, retention of the metastable β phase began. However, when 4 mass% Fe or greater was added, the β phase was entirely retained with a bcc crystal structure. Moreover, the ω phase was only detected in the Ti-5Nb-2Fe, Ti-5Nb-3Fe and Ti-5Nb-4Fe alloys. The largest quantity of ω phase and the highest bending modulus were found in the Ti-5Nb-3Fe alloy. The Ti-5Nb-2Fe alloy had the lowest bending modulus, which was lower than that of c.p. Ti by 20%. This alloy exhibited the highest bending strength/modulus ratio of 26.7, which was higher than that of c.p. Ti by 214%, and of the Ti-5Nb alloy (14.4 ) by 85%. Additionally, the elastically recoverable angles of the ductile Ti-5Nb-1Fe (19.9 o ) and Ti-5Nb-5Fe (29.5 o ) alloys were greater than that of c.p. Ti (2.7 o ) by as much as 637% and 993%, respectively. Furthermore, the preliminary cell culturing results revealed that the Ti-5Nb-xFe alloys were not only biocompatible, but also supported cell attachment.

Structure and mechanical properties of as-cast Ti-5Nb-xFe alloys

Energy Technology Data Exchange (ETDEWEB)

Hsu, Hsueh-Chuan; Hsu, Shih-Kuang; Wu, Shih-Ching [Department of Dental Laboratory Technology, Central Taiwan University of Science and Technology, Taichung 40605, Taiwan (China); Institute of Biomedical Engineering and Material Science, Central Taiwan University of Science and Technology, Changhua 51591, Taiwan (China); Lee, Chih-Jhan [Department of Materials Science and Engineering, Da-Yeh University, Changhua 51591, Taiwan (China); Ho, Wen-Fu, E-mail: fujii@mail.dyu.edu.tw [Department of Materials Science and Engineering, Da-Yeh University, Changhua 51591, Taiwan (China)

2010-09-15

In this study, as-cast Ti-5Nb and a series of Ti-5Nb-xFe alloys were investigated and compared with commercially pure titanium (c.p. Ti) in order to determine their structure and mechanical properties. The series of Ti-5Nb-xFe alloys contained an iron content ranging from 1 to 5 mass% and were prepared by using a commercial arc-melting vacuum-pressure casting system. Additionally, X-ray diffraction (XRD) for phase analysis was conducted with a diffractometer, and three-point bending tests were performed to evaluate the mechanical properties of all specimens. The fractured surfaces were observed by using scanning electron microscopy (SEM). The experimental results indicated that these alloys possessed a range of different structures and mechanical properties dependent upon the various additions of Fe. With an addition of 1 mass% Fe, retention of the metastable {beta} phase began. However, when 4 mass% Fe or greater was added, the {beta} phase was entirely retained with a bcc crystal structure. Moreover, the {omega} phase was only detected in the Ti-5Nb-2Fe, Ti-5Nb-3Fe and Ti-5Nb-4Fe alloys. The largest quantity of {omega} phase and the highest bending modulus were found in the Ti-5Nb-3Fe alloy. The Ti-5Nb-2Fe alloy had the lowest bending modulus, which was lower than that of c.p. Ti by 20%. This alloy exhibited the highest bending strength/modulus ratio of 26.7, which was higher than that of c.p. Ti by 214%, and of the Ti-5Nb alloy (14.4 ) by 85%. Additionally, the elastically recoverable angles of the ductile Ti-5Nb-1Fe (19.9{sup o}) and Ti-5Nb-5Fe (29.5{sup o}) alloys were greater than that of c.p. Ti (2.7{sup o}) by as much as 637% and 993%, respectively. Furthermore, the preliminary cell culturing results revealed that the Ti-5Nb-xFe alloys were not only biocompatible, but also supported cell attachment.

Diffusion barrier performance of novel Ti/TaN double layers for Cu metallization

International Nuclear Information System (INIS)

Zhou, Y.M.; He, M.Z.; Xie, Z.

2014-01-01

Highlights: • Novel Ti/TaN double layers offering good stability as a barrier against Cu metallization have been made achievable by annealing in vacuum. • The Ti/TaN double layers improved the adhesion with Cu thin films and showed good diffusion barrier between Cu and SiO 2 /Si up to the annealing condition. • The failure mechanism of Ti/TaN bi-layer is similar with the Cu/TaN/Si metallization system in which Cu atoms diffuse through the grain boundary of barrier and react with silicon to form Cu 3 Si. - Abstract: Novel Ti/TaN double layers offering good stability as a barrier against Cu metallization have been made achievable by annealing in vacuum better than 1 × 10 −3 Pa. Ti/TaN double layers were formed on SiO 2 /Si substrates by DC magnetron sputtering and then the properties of Cu/Ti/TaN/SiO 2 /Si film stacks were studied. It was found that the Ti/TaN double layers provide good diffusion barrier between Cu and SiO 2 /Si up to 750 °C for 30 min. The XRD, Auger and EDS results show that the Cu–Si compounds like Cu 3 Si were formed by Cu diffusion through Ti/TaN barrier for the 800 °C annealed samples. It seems that the improved diffusion barrier property of Cu/Ti/TaN/SiO 2 /Si stack is due to the diffusion of nitrogen along the grain boundaries in Ti layer, which would decrease the defects in Ti film and block the diffusion path for Cu diffusion with increasing annealing temperature. The failure mechanism of Ti/TaN bi-layer is similar to the Cu/TaN/Si metallization system in which Cu atoms diffuse through the grain boundary of barrier and react with silicon to form Cu 3 Si

Extreme and Local 3rd Harmonic Response of Niobium (Nb) Superconductor

Science.gov (United States)

Oripov, Bakhrom; Tai, Tamin; Anlage, Steven

Superconducting Radio Frequency (SRF) cavities are being widely used in new generation particle accelerators. These SRF cavities are based on bulk Nb. Based on the needs of the SRF community to identify defects on Nb surfaces, a novel near-field magnetic microwave microscope was successfully built using a magnetic writer from a conventional magnetic recording hard-disk drive1. This magnetic writer can create an RF magnetic field, localized and strong enough to drive Nb into the vortex state. This probe enables us to locate defects through scanning and mapping of the local electrodynamic response in the multi-GHz frequency range. Recent measurements have shown that 3rd harmonic nonlinear response is far more sensitive to variations in input power and temperature then linear response, thus we mainly study the 3rd harmonic response. Moreover, the superconductor is usually the only source for nonlinear response in our setup, thus there is less chance of having noise or background signal. Understanding the mechanism responsible for this non-linear response is important for improving the performance of SRF cavities. Besides Nb we also study various other superconductors such as MgB2 and the cuprate Bi-Sr-Ca-Cu-O (BSCCO) for potential applications in SRF cavities. This work is funded by US Department of Energy through Grant # DE-SC0012036T and CNAM.

Ac losses of transposed superconductors

International Nuclear Information System (INIS)

Eckert, D.; Enderlein, G.; Lange, F.

1975-01-01

Eastham and Rhodes published results of loss measurements on transposed superconducting NbTi cables and concluded basing on an extrapolation to very large numbers of wires that transposed superconductors could be used favorably in cables for power transmission. There are some reasons to question the correctness of their extrapolation. Losses were calculated for transposed superconductors in self field and got results different from those of Eastham and Rhodes. Loss measurements were performed the results of which give evidence for the correctness of our calculations. The results lead to the conclusion that the use of transposed cables of irreversible type 2 superconductors for power transmission is not advantageous

High temperature oxidation of β-NbTi alloys

International Nuclear Information System (INIS)

Parida, S.C.; Gupta, N.K.; Rama Rao, G.A.; Sen, B.K.; Krishnan, K.

2008-01-01

The isothermal oxidation kinetics of pure Ti metal and two different β-NbTi alloys with compositions of 85 and 75 at.% Ti were studied using thermogravimetric technique in the temperature range of 1073-1323 K at an interval of 50 K. The value of the power exponent n of the rate equation was found to be close to one suggesting that each reaction follows first order kinetic rate law. X-ray diffraction analysis of oxidation products at each temperature revealed the simultaneous formation of TiO 2 and TiNb 2 O 7 . The rate constants and the activation energies of oxidation reactions for each alloy compositions were evaluated. (author)

Electrochemical and surface behavior of hydyroxyapatite/Ti film on nanotubular Ti-35Nb-xZr alloys

International Nuclear Information System (INIS)

Jeong, Yong-Hoon; Choe, Han-Cheol; Brantley, William A.

2012-01-01

In this paper, we investigated the electrochemical and surface behavior of hydroxyapatite (HA)/Ti films on the nanotubular Ti-35Nb-xZr alloy. The Ti-35Nb-xZr ternary alloys with 3-10 wt.% Zr content were made by an arc melting method. The nanotubular oxide layers were developed on the Ti-35Nb-xZr alloys by an anodic oxidation method in 1 M H 3 PO 4 electrolyte containing 0.8 wt% NaF at room temperature. The HA/Ti composite films on the nanotubular oxide surfaces were deposited by a magnetron sputtering method. Their surface characteristics were analyzed by field-emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectroscopy (EDS) and an X-ray diffractometer (XRD). The corrosion behavior of the specimens was examined through potentiodynamic and AC impedance tests in 0.9% NaCl solution. From the results, the Ti-35Nb-xZr alloys showed a solely β phase microstructure that resulted from the addition of Zr. The nanotubular structure formed with a diameter of about 200 nm, and the HA/Ti thin film was deposited on the nanotubular structure. The HA/Ti thin film-coated nanotubular Ti-35Nb-xZr alloys showed good corrosion resistance in 0.9% NaCl solution.

Structural evolution of Ba8Ti3Nb4O24 from BaTiO3 using a series of Ba(Ti1−5xNb4x)O3 solid solutions

International Nuclear Information System (INIS)

Barrientos Hernández, F.R.; Lira Hernández, I.A.; Gómez Yáñez, C.; Arenas Flores, A.; Cabrera Sierra, R.; Pérez Labra, M.

2014-01-01

Highlights: • The evolution phase Ba 8 Ti 3 Nb 4 O 24 was obtained through the mechanism Ba(Ti 1-5x Nb 4x )O 3 . • Addition of niobium can accelerate grain growth of BaTiO 3 ceramics. • Ba 8 Ti 3 Nb 4 O 24 presents a dielectric loss of 0.0035 and permittivity value of 54.6. • Electrical measurements showed that Nb 5+ content drops Curie temperature. • Samples with x ⩾ 0.0625 shows an insulating behavior. -- Abstract: In this work, the structural evolution of hexagonal phase Ba 8 Ti 3 Nb 4 O 24 by adding Nb 2 O 5 to perovskite structure of BaTiO 3 was investigated. The compositions Ba(Ti 1-5x Nb 4x )O 3 ceramics, with 0.00025 ⩽ x ⩽ 0.125 were prepared by the conventional solid state route in air atmosphere, the powders precursors, BaTiO 3 , BaCO 3 and Nb 2 O 5 , were mixed in stoichiometric proportions and ground in a ball mill using alumina balls and acetone. The mixed powders were calcined at temperatures up to 1500 °C. The phase transformation of Ba 8 Ti 3 Nb 4 O 24 from BaTiO 3 was studied by DRX, Raman spectroscopy, SEM, electrical measurements (relative permittivity and P–E hysteresis loops); Rietveld’s refinement was used to structurally characterize the samples. For the devices obtained capacitance was measured at 1 kHz; with these values we calculated the relative permittivity. The samples show typical P–E hysteresis loops at room temperature accompanied by saturation polarization (Ps) and remnant polarization (Pr). The DRX and Rietveld’s refinement results show x ⩽ 0.01 has a ferroelectric behavior. When the doped level is increased x ⩾ 0.02, a peak displacement is observed, this is due to the phase transformation of tetragonal to cubic into the unit cell. Finally, with x = 0.125 the crystal structure transforms to the characteristic hexagonal phase Ba 8 Ti 3 Nb 4 O 24 which resonates at microwave frequencies

High-field superconductivity in the Nb-Ti-Zr ternary system

International Nuclear Information System (INIS)

Ralls, K.M.; Rose, R.M.; Wulff, J.

1980-01-01

Resistive critical current densities, critical fields, and normal-state electrical resistivities were obtained at 4.2 0 K for 55 alloys in the Nb-Ti-Zr ternary alloy system, excepting Ti-Zr binary compositions. The resistive critical field as a function of ternary composition has a saddle point between the Nb-Ti and Nb-Zr binaries, so that ternary alloying in this system is not expected to result in higher critical fields than the binary alloys

High-field superconductivity in the Nb-Ti-Zr ternary system

Science.gov (United States)

Ralls, K. M.; Rose, R. M.; Wulff, J.

1980-06-01

Resistive critical current densities, critical fields, and normal-state electrical resistivities were obtained at 4.2 °K for 55 alloys in the Nb-Ti-Zr ternary alloy system, excepting Ti-Zr binary compositions. The resistive critical field as a function of ternary composition has a saddle point between the Nb-Ti and Nb-Zr binaries, so that ternary alloying in this system is not expected to result in higher critical fields than the binary alloys.

Extraordinary high strength Ti-Zr-Ta alloys through nanoscaled, dual-cubic spinodal reinforcement.

Science.gov (United States)

Biesiekierski, Arne; Ping, Dehai; Li, Yuncang; Lin, Jixing; Munir, Khurram S; Yamabe-Mitarai, Yoko; Wen, Cuie

2017-04-15

While titanium alloys represent the current state-of-the-art for orthopedic biomaterials, concerns still remain over their modulus. Circumventing this via increased porosity requires high elastic admissible strains, yet also limits traditional thermomechanical strengthening techniques. To this end, a novel β-type Ti-Zr-Ta alloy system, comprised of Ti-45Zr-10Ta, Ti-40Zr-14Ta, Ti-35Zr-18Ta and Ti-30Zr-22Ta, was designed and characterized mechanically and microstructurally. As-cast, this system displayed extremely high yield strengths and elastic admissible strains, up to 1.4GPa and potentially 1.48%, respectively. This strength was attributed to a nanoscaled, cuboidal structure of semi-coherent, dual body-centered cubic (BCC) phases, arising from the thermodynamics of interaction between Ta and Zr; this morphology occurring with dual BCC-phases is heretofore unreported in Ti-based alloys. Further, cell proliferation investigated by MTS assay suggests this was achieved without sacrificing biocompatibility, with no significant difference to either empty-well or commercially-pure Ti controls noted. The current research details microstructural, mechanical, and biological investigations into four novel biomedical alloys in a hitherto uninvestigated region of the Ti-Zr-Ta alloy system; Ti-45Zr-10Ta, Ti-40Zr-14Ta, Ti-35Zr-18Ta and Ti-30Zr-22Ta. We find that the investigated alloys display 0.2% yield strengths of up to 1.40GPa and elastic admissible strains of up to 1.48%, along with biological properties comparable to that seen in the conventional metallic biomaterial ASTM Grade-2 CP-Ti, achieved in the complete absence of traditional thermomechanical processing techniques. This is attributed to the presence of a dual-BCC cuboidal nanostructure, achieved via spinodal decomposition; while similar structures have been reported in e.g. Ni-based superalloys, we believe this is the first such structure investigated in a Ti-based material. As such, this work is felt to be of

Voltage current characteristics of type III superconductors

International Nuclear Information System (INIS)

Dorofejev, G.L.; Imenitov, A.B.; Klimenko, E.Y.

1980-01-01

An adequate description of voltage-current characteristics is important in order to understand the nature of high critical current for the electrodynamic construction of type-III superconductors and for commercial superconductor specification. Homogeneous monofilament and multifilament Nb-Ti, Nb-Zr,Nb 3 Sn wires were investigated in different ranges of magnetic field, temperature and current. The shape of the voltage-current characteristics of multifilament wires, and the parameter's dependence on temperature and magnetic field may be explained qualitatively by the longitudinal heterogeneous nature of the filaments. A method of attaining the complete specification of the wire's electro-physical properties is proposed. It includes the traditional description of a critical surface (i.e. the surface corresponding to a certain conventional effective resistivity in T,B,J-space) and a description of any increasing parameter that depends on B and T. (author)

Voltage current characteristics of type III superconductors

Energy Technology Data Exchange (ETDEWEB)

Dorofeiev, G L; Imenitov, A B; Klimenko, E Y [Gosudarstvennyi Komitet po Ispol' zovaniyu Atomnoi Ehnergii SSSR, Moscow. Inst. Atomnoi Ehnergii

1980-06-01

An adequate description of voltage-current characteristics is important in order to understand the nature of high critical current for the electrodynamic construction of type-III superconductors and for commercial superconductor specification. Homogeneous monofilament and multifilament Nb-Ti, Nb-Zr,Nb/sub 3/Sn wires were investigated in different ranges of magnetic field, temperature and current. The shape of the voltage-current characteristics of multifilament wires, and the parameter's dependence on temperature and magnetic field may be explained qualitatively by the longitudinal heterogeneous nature of the filaments. A method of attaining the complete specification of the wire's electro-physical properties is proposed. It includes the traditional description of a critical surface (i.e. the surface corresponding to a certain conventional effective resistivity in T,B,J-space) and a description of any increasing parameter that depends on B and T.

Enhancement in the high-T{sub c} phase of BSCCO superconductors by Nb addition

Energy Technology Data Exchange (ETDEWEB)

Soezeri, Hueseyin [TUBITAK-UME, National Metrology Institute, PO Box 54 TR-41470, Gebze Kocaeli (Turkey); Ghazanfari, Nader [Middle East Technical University, Physics Department, 06531 Ankara (Turkey); Oezkan, Huesnue [Middle East Technical University, Physics Department, 06531 Ankara (Turkey); Kilic, Ahmet [Middle East Technical University, Physics Department, 06531 Ankara (Turkey)

2007-06-15

Pure and Nb{sub 2}O{sub 5} added Bi{sub 1.6}Pb{sub 0.4}Nb{sub x}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub {delta}} superconductors (x varies up to 0.30) were synthesized by the solid state reaction method. Structural and superconducting properties of the samples were investigated. The fraction of the high-T{sub c} phase (2223) increases with Nb addition up to x = 0.10, for which a nearly single 2223 phase was obtained. The critical temperature of the samples increases from 96 to 104 K with doping up to x = 0.20 and a further increase in Nb decreases the T{sub c} sharply. Similarly, there is a considerable enhancement in the critical current density (j{sub c}) of the samples in the same doping range. Both AC susceptibility and transport measurements showed that the optimum Nb concentration is x = 0.20. The out-of-phase component of the AC susceptibility measurements showed that inter-grain coupling was enhanced up to the same doping level. Nb additions above x = 0.30 decrease the fraction of the high-T{sub c} phase and degrade the superconducting properties. Present measurements indicate that x = 0.20 is the optimum Nb concentration in the BSCCO superconductor to enhance phase purity, inter-grain coupling and superconducting parameters (T{sub c} and j{sub c})

New ternary tantalum borides containing boron dumbbells: Experimental and theoretical studies of Ta{sub 2}OsB{sub 2} and TaRuB

Energy Technology Data Exchange (ETDEWEB)

Mbarki, Mohammed; Touzani, Rachid St.; Rehorn, Christian W.G.; Gladisch, Fabian C. [Institute of Inorganic Chemistry, RWTH Aachen University, D-52056 Aachen (Germany); Fokwa, Boniface P.T., E-mail: bfokwa@ucr.edu [Institute of Inorganic Chemistry, RWTH Aachen University, D-52056 Aachen (Germany); Department of Chemistry, University of California Riverside (UCR), Riverside, CA 92521 (United States)

2016-10-15

The new ternary transition metal-rich borides Ta{sub 2}OsB{sub 2} and TaRuB have been successfully synthesized by arc-melting the elements in a water-cooled crucible under an argon atmosphere. The crystal structures of both compounds were solved by single-crystal X-ray diffraction and their metal compositions were confirmed by EDX analysis. It was found that Ta{sub 2}OsB{sub 2} and TaRuB crystallize in the tetragonal Nb{sub 2}OsB{sub 2} (space group P4/mnc, no. 128) and the orthorhombic NbRuB (space group Pmma, no. 51) structure types with lattice parameters a=5.878(2) Å, c=6.857(2) Å and a=10.806(2) Å, b=3.196(1) Å, c=6.312(2) Å, respectively. Furthermore, crystallographic, electronic and bonding characteristics have been studied by density functional theory (DFT). Electronic structure relaxation has confirmed the crystallographic parameters while COHP bonding analysis indicates that B{sub 2}-dummbells are the strongest bonds in both compounds. Moreover, the formation of osmium dumbbells in Ta{sub 2}OsB{sub 2} through a Peierls distortion along the c-axis, is found to be the origin of superstructure formation. Magnetic susceptibility measurements reveal that the two phases are Pauli paramagnets, thus confirming the theoretical DOS prediction of metallic character. Also hints of superconductivity are found in the two phases, however lack of single phase samples has prevented confirmation. Furthermore, the thermodynamic stability of the two modifications of AMB (A=Nb, Ta; M =Ru, Os) are studied using DFT, as new possible phases containing either B{sub 4}- or B{sub 2}-units are predicted, the former being the most thermodynamically stable modification. - Graphical abstract: The two new ternary tantalum borides, Ta{sub 2}OsB{sub 2} and TaRuB, have been discovered. Their crystal structures contain boron dumbbells, which are the strongest bonds. Peirls distortion is found responsible for Os{sub 2}-dumbbells formation in Ta{sub 2}OsB{sub 2}. Ta{sub 2}OsB{sub 2} and

Resistance to He{sup 2+} irradiation damage in metallic glass Ta{sub 38}Ni{sub 62}

Energy Technology Data Exchange (ETDEWEB)

Hou, Wenjing [Key Laboratory of Materials Modification by Laser, Ion and Electron Beams (Dalian University of Technology), Ministry of Education, Dalian 116024 (China); Mei, Xianxiu, E-mail: xxmei@dlut.edu.cn [Key Laboratory of Materials Modification by Laser, Ion and Electron Beams (Dalian University of Technology), Ministry of Education, Dalian 116024 (China); Zhang, Xiaonan; Wang, Yingmin; Qiang, Jianbing [Key Laboratory of Materials Modification by Laser, Ion and Electron Beams (Dalian University of Technology), Ministry of Education, Dalian 116024 (China); Sun, Jianrong [Institute of Modern Physics, The Chinese Academy of Sciences, Lanzhou 730000 (China); Wang, Younian [Key Laboratory of Materials Modification by Laser, Ion and Electron Beams (Dalian University of Technology), Ministry of Education, Dalian 116024 (China)

2016-10-15

Highlights: • Metallic glass Ta{sub 38}Ni{sub 62} irradiated by different fluence of He{sup 2+} remained amorphous. • The helium bubble layer appeared at the end of ion range 1.01 μm away from surface. • Helium bubbles were larger in the layer center and reduced to top and bottom sides. • No significant damage appeared in the surface of metallic glass Ta{sub 38}Ni{sub 62}. • Ta{sub 38}Ni{sub 62} better resisted to He{sup 2+} irradiation than W and V{sub 87.5}Cr{sub 4.17}Ti{sub 4.17}Nb{sub 4.17}. - Abstract: Metallic glass Ta{sub 38}Ni{sub 62} strips, metallic W, and V{sub 87.5}Cr{sub 4.17}Ti{sub 4.17}Nb{sub 4.17} alloy were irradiated using a 500 keV He{sup 2+} ion beam at different fluence to compare the metallic glass resistance to irradiation. Metallic glass Ta{sub 38}Ni{sub 62} remained amorphous at different He{sup 2+} irradiation fluence. Transmission electron microscopy analysis revealed the presence of helium bubbles at the end of the range of helium ions in the metallic glass. No significant damage resulted in the metallic glass surface, and the root mean square roughness increased nonlinearly with the increase in fluence. At 1 × 10{sup 18} ions/cm{sup 2}, metallic W appeared in larger sunken areas on the surface and V{sub 87.5}Cr{sub 4.17}Ti{sub 4.17}Nb{sub 4.17} alloy experienced multi-layer flaking. The metallic glass Ta{sub 38}Ni{sub 62} resistance to He{sup 2+} ion beam irradiation was better than that of metallic W, and that of the V{sub 87.5}Cr{sub 4.17}Ti{sub 4.17}Nb{sub 4.17} alloy was the poorest.

New intermetallic MIrP (M=Ti, Zr, Nb, Mo) and MgRuP compounds related with MoM'P (M'=Ni and Ru) superconductor

Science.gov (United States)

Kito, Hijiri; Iyo, Akira; Wada, Toshimi

2011-01-01

Using a cubic-anvil high-pressure apparatus, ternary iridium phosphides MIrP (M=Ti, Zr, Nb, Mo) and MgRuP have been prepared by reaction of stoichiometric amounts of each metal and phosphide powders at around 2 Gpa and above 1523 K for the first time. The structure of these compounds prepared at high-pressure has been characterized by X-ray powder diffraction. Diffraction lines of these compounds are assigned by the index of the Co2Si-type structure. The electrical resistivity and the d.c magnetic susceptibility of MIrP (M=Ti, Zr, Nb, Mo) have measured at low temperatures. Unfortunately, no superconducting transition for MIrP (M=Ti, Zr, Nb, Mo) and MgRuP are observed down to 2 K.

New intermetallic MIrP (M=Ti, Zr, Nb, Mo) and MgRuP compounds related with MoM'P (M'=Ni and Ru) superconductor

International Nuclear Information System (INIS)

Kito, Hijiri; Iyo, Akira; Wada, Toshimi

2011-01-01

Using a cubic-anvil high-pressure apparatus, ternary iridium phosphides MIrP (M=Ti, Zr, Nb, Mo) and MgRuP have been prepared by reaction of stoichiometric amounts of each metal and phosphide powders at around 2 Gpa and above 1523 K for the first time. The structure of these compounds prepared at high-pressure has been characterized by X-ray powder diffraction. Diffraction lines of these compounds are assigned by the index of the Co 2 Si-type structure. The electrical resistivity and the d.c magnetic susceptibility of MIrP (M=Ti, Zr, Nb, Mo) have measured at low temperatures. Unfortunately, no superconducting transition for MIrP (M=Ti, Zr, Nb, Mo) and MgRuP are observed down to 2 K.

Synchrotron radiation techniques for the characterization of Nb$_{3}$Sn superconductors

CERN Document Server

Scheuerlein, C; Buta, F

2009-01-01

The high flux of high energy x-rays that can be provided through state-of-the-art high energy synchrotron beam lines has enabled a variety of new experiments with the highly absorbing Nb$_{3}$Sn superconductors. We report different experiments with Nb$_{3}$Sn strands that have been conducted at the ID15 High Energy Scattering beam line of the European Synchrotron Radiation Facility (ESRF). Synchrotron x-ray diffraction has been used in order to monitor phase transformations during in-situ reaction heat treatments prior to Nb$_{3}$Sn formation, and to monitor Nb$_{3}$Sn growth. Fast synchrotron micro-tomography was applied to study void growth during the reaction heat treatment of Internal Tin strands. The elastic strain in the different phases of fully reacted Nb$_{3}$Sn composite conductors can be measured by high resolution x-ray diffraction during in-situ tensile tests.

Electrochemical characterization and redox behavior of Nb-doped SrTiO3

DEFF Research Database (Denmark)

Blennow Tullmar, Peter; Kammer Hansen, Kent; Wallenberg, L. Reine

2009-01-01

Sr-vacancy compensated Nb-doped SrTiO3 with the nominal composition Sr0.94Ti0.9Nb0.1O3 has been evaluated as a solid oxide fuel cell (SOFC) anode material in terms of redox stability and electrochemical properties. Sr0.94Ti0.9Nb0.1O3 has been synthesized with a recently developed modified glycine......-nitrate process. The phase purity and redox behavior have been analyzed with XRD and TGA. The electrochemical properties of Sr0.94Ti0.9Nb0.1O3 and a composite electrode of Sr0.94Ti0.9Nb0.1O3/YSZ have been investigated by electrochemical impedance spectroscopy (EIS) on cone shaped electrodes and on electrodes...... in a symmetrical cell configuration. The experiments indicated that the Nb-doped SrTiO3 electrodes were redox stable and showed a potential ability to be used as a part of a SOFC anode. The electrochemical activity appeared to be governed by the concentration of defect species (especially Ti3+ and V-0...

On the hardenability of Nb-modified metastable beta Ti-5553 alloy

Energy Technology Data Exchange (ETDEWEB)

Campo, K.N.; Andrade, D.R.; Opini, V.C.; Mello, M.G.; Lopes, E.S.N.; Caram, R., E-mail: caram@fem.unicamp.br

2016-05-15

Among the commercially available titanium alloys, the metastable β Ti-5553 alloy (Ti–5Al–5V–5Mo–3Cr–0.5Fe wt.%) is an object of great interest because it is employed in aerospace structural applications, primarily in the replacement of steel components. One of the primary advantages of this alloy is its high hardenability, which allows it to retain the β phase at room temperature, even at low cooling rates, thereby allowing the thermoprocessing of thick parts. The aim of this investigation was to evaluate the effect of the replacement of V with Nb on the hardenability of Ti-5553. Based on the molybdenum equivalent criterion, the Nb-modified Ti-5553 alloy was designed to present 12 wt.% of Nb instead of 5 wt.% of V. Samples of both alloys were prepared by melting them in an arc furnace under an inert atmosphere, heat-treated at high temperatures for 12 h and plastic deformed using swage forging. Finally, these samples were solution heat-treated at temperatures above the β-transus followed by cooling at different rates using water quenching, furnace cooling and a modified Jominy end quench test. Characterization was performed by measuring Vickers hardness, X-ray diffraction, and light optical, scanning electron and transmission electron microscopy. The results obtained indicate that metastable β phase can be retained when the cooling rate is higher than 21 °C/s for both alloys. At lower cooling rates, α phase precipitation was observed, but it appeared to be less evident in the Nb-modified Ti-5553, suggesting that the replacement of V with Nb increased the hardenability of the alloy. - Highlights: • Hardenability of Ti alloys are assessed using a modified Jominy end quench test. • Ti-5553 and Nb-modified Ti-5553 are subjected to continuous cooling experiments. • β phase decomposition kinetics is reduced by replacing V with Nb in Ti-5553. • Nb-modified Ti-5553 features improved hardenability. • Replacement of V with Nb causes the �

Cu-Ti Formation in Nb-Ti/Cu Superconducting Strand Monitored by in situ Techniques

CERN Document Server

Pong, I; Pong, Ian; Gerardin, Alexandre; Scheuerlein, Christian; Bottura, Luca

2010-01-01

In order to investigate the high temperature exposure effect on Nb-Ti/Cu superconducting strands, as might be encountered in joining by soldering and in cabling annealing, X-ray diffraction and resistometry measurements were performed in situ during heat treatment, and complemented by conventional metallography, mechanical tests and superconducting properties measurements. Changes of the Nb-Ti nanostructure at temperatures above 300 degrees C are manifested in the degradation of critical current in an applied external magnetic field, although degradation at self field was insignificant up to 400 degrees C for several minutes. Above 500 degrees C, the formation of various Cu-Ti intermetallic compounds, due to Ti diffusion from Nb-Ti into Cu, is detected by in situ XRD albeit not resolvable by SEM-EDS. There is a ductile to brittle transition near 600 degrees C, and liquid formation is observed below 900 degrees C. The formation of Cu-Ti causes a delayed reduction of the residual resistivity ratio (RRR) and adv...

Workshop on Accelerator Magnet Superconductors, Design and Optimization

CERN Document Server

WAMSDO Workshop

2009-01-01

This report contains the proceedings of the CARE-HHH-AMT Workshop on Accelerator Magnet Superconductors, Design and Optimization (WAMSDO) held at CERN from 19 to 23 May 2008. The needs in terms of superconducting magnets for the accelerator projects were discussed, mainly for the LHC interaction regions and injector upgrades, and for the GSI FAIR complex. The first part of the workshop focused on the development of superconductor and cables, i.e., low-loss Nb-Ti cables, Nb$_{3}$Sn and high-temperature superconductors. An industry session summarized the actual plans and status of the activities in the main European industries. Then, a worldwide status of the high field magnets programme was presented. A special session was devoted to fast cycled magnets, including FAIR facilities and LHC injector upgrades. A final session focused on the optimization methods and numerical tools for magnet design.

Hydriding and dehydriding rates of Mg, Mg-10TaF5, and Mg-10NbF5 prepared via reactive mechanical grinding

Science.gov (United States)

Song, Myoung Youp; Kwak, Young Jun; Lee, Seong Ho; Park, Hye Ryoung

2015-01-01

In this work, TaF5 and NbF5 were chosen as additives to enhance the hydriding and dehydriding rates of Mg. Mg, Mg-10TaF5, and Mg-10NbF5 samples were prepared by reactive mechanical grinding. The hydriding and dehydriding properties of the samples were then examined. Mg-10TaF5 had the largest amount of hydrogen absorbed for 30 min and the highest initial dehydriding rate after incubation period, followed in order by Mg-10NbF5, and Mg. At 593 K under 12 bar H2 at the first cycle, Mg-10TaF5 absorbed 3.63 wt% H for 5 min and 4.53 wt% H for 30 min. At 593 K under 1.0 bar H2 at the first cycle, Mg-10TaF5 desorbed 0 wt% H for 2.5 min, 0.59 wt% H for 5 min, 3.42 wt% H for 30 min, and 4.24 wt% H for 60 min. The reactive mechanical grinding of Mg with TaF5 or NbF5 is believed to have facilitated the nucleation and to have decreased the diffusion distances of hydrogen atoms. These two effects are believed to have increased the hydriding and dehydriding rates of Mg. The MgF2 and Ta2H formed in Mg-10TaF5, and the MgF2, NbH2, and NbF3 formed in Mg-10NbF5 are considered to have enhanced both of these effects.

Quantitative description of a high Jc Nb-Ti superconductor during its final optimization strain. I. Microstructure, Tc, Hc2, and resistivity

International Nuclear Information System (INIS)

Meingast, C.; Lee, P.J.; Larbalestier, D.C.

1989-01-01

A most important step in the critical current density (J c ) optimization of Nb-Ti is the large final drawing strain, in which α-Ti precipitates, initially approximately equiaxed and 100--200 nm in diameter, are drawn into ribbons, whose thickness (1--2 nm) is less than the superconducting coherence length [ξ (4.2 K)∼5 nm]. Using transmission electron microscopy, the precipitate thickness, spacing, cross-sectional area, and circumference were measured over the whole final drawing strain range. Each of these parameters was found to have a simple power dependence on the wire diameter. T c , H c2 , and the resistivity (ρ n ) were also change considerably during the refinement of the precipitates. Directly after precipitation, T c increased, and (dH c2 /dT) T c and ρ n were reduced from the single-phase values. Drawing the wire returned these parameters to their single-phase values, as the precipitate thickness was reduced to less than ξ. This observation explains a long-standing peculiarity in this system, namely that the optimum H c2 of high J c conductors occurs for a composition close to Nb 46 wt.% Ti, even when the precipitation of 18 vol % of α-Ti shifts the matrix composition to a Nb-rich composition of theoretically lower H c2

Development of superconductor application technology

Energy Technology Data Exchange (ETDEWEB)

Hong, G W; Kim, C J; Lee, H G; Lee, H J; Kim, K B; Won, D Y; Jang, K I; Kwon, S C; Kim, W J; Ji, Y A; Yang, S W; Kim, W K; Park, S D; Lee, M H; Lee, D M; Park, H W; Yu, J K; Lee, I S; Kim, J J; Choi, H S; Chu, Y; Kim, Y S; Kim, D H

1997-09-01

Fabrication of high Tc bulk superconductor and its application, fabrication of superconducting wire for electric power device and analysis for cryogenic system were carried out for developing superconductor application technologies for electric power system. High quality YBaCuO bulk superconductor was fabricated by controlling initial powder preparation process and prototype flywheel energy storage device was designed basically. The superconducting levitation force measuring device was made to examine the property of prepared superconductor specimen. Systematic studies onthe method of starting powder preparation, mechanical fabrication process, heat treatment condition and analysis of plastic deformation were carried out to increase the stability and reproducibility of superconducting wire. A starting power with good reactivity and fine particle size was obtained by mechanical grinding, control of phase assemblage, and emulsion drying method. Ag/BSCCO tape with good cross sectional shape and Jc of 20,000 A/cm{sup 2} was fabricated by applying CIP packing procedure. Multifilamentary wire with Jc of 10,000 A/cm{sup 2} was fabricated by rolling method using square billet as starting shape. The joining of the multifilamentary wire was done by etching and pressing process and showed 50% of joining efficiency. Analysis on the heat loss in cryostat for high Tc superconducting device was carried out for optimum design of the future cryogenic system. (author). 66 refs., 104 figs.

Development of superconductor application technology

International Nuclear Information System (INIS)

Hong, G. W.; Kim, C. J.; Lee, H. G.; Lee, H. J.; Kim, K. B.; Won, D. Y.; Jang, K. I.; Kwon, S. C.; Kim, W. J.; Ji, Y. A.; Yang, S. W.; Kim, W. K.; Park, S. D.; Lee, M. H.; Lee, D. M.; Park, H. W.; Yu, J. K.; Lee, I. S.; Kim, J. J.; Choi, H. S.; Chu, Y.; Kim, Y. S.; Kim, D. H.

1997-09-01

Fabrication of high Tc bulk superconductor and its application, fabrication of superconducting wire for electric power device and analysis for cryogenic system were carried out for developing superconductor application technologies for electric power system. High quality YBaCuO bulk superconductor was fabricated by controlling initial powder preparation process and prototype flywheel energy storage device was designed basically. The superconducting levitation force measuring device was made to examine the property of prepared superconductor specimen. Systematic studies onthe method of starting powder preparation, mechanical fabrication process, heat treatment condition and analysis of plastic deformation were carried out to increase the stability and reproducibility of superconducting wire. A starting power with good reactivity and fine particle size was obtained by mechanical grinding, control of phase assemblage, and emulsion drying method. Ag/BSCCO tape with good cross sectional shape and Jc of 20,000 A/cm 2 was fabricated by applying CIP packing procedure. Multifilamentary wire with Jc of 10,000 A/cm 2 was fabricated by rolling method using square billet as starting shape. The joining of the multifilamentary wire was done by etching and pressing process and showed 50% of joining efficiency. Analysis on the heat loss in cryostat for high Tc superconducting device was carried out for optimum design of the future cryogenic system. (author). 66 refs., 104 figs

The structural and electronic properties of cubic AgMO{sub 3} (M=Nb, Ta) by first principles calculations

Energy Technology Data Exchange (ETDEWEB)

Prasad, K. Ganga; Niranjan, Manish K.; Asthana, Saket [Department of Physics, Indian Institute of Technology Hyderabad, India, 502205 (India)

2016-05-06

We report the electronic structure of the AgMO{sub 3}(M=Nb, Ta) within the frame work of density functional theory and calculations are performed within the generalized gradient approximation (GGA) by using ultrasoft pseudopotentials. The calculated equilibrium lattice parameters and volumes are extracted from fitting of Birch third order equation of state and which are reasonable agreement with the available experimental results. The density of states,band structure of Ag(Nb,Ta)O{sub 3} reveals that the valance bands mostly occupied with O-2p and O-2s states and whereas conduction band occupied with Nb (Ta) 4d(5d) states including less contribution from Ag 5s states.

Phase transition and piezoelectric properties of K0.48Na0.52NbO3-LiTa0.5Nb0.5O3-NaNbO3 lead-free ceramics

International Nuclear Information System (INIS)

Gao Feng; Liu Liangliang; Xu Bei; Cao Xiao; Deng Zhenqi; Tian Changsheng

2011-01-01

Highlights: → The evolution of the crystal structure for the new phase K 3 Li 2 Nb 5 O 15 was described. → The dielectric relaxor behavior would be strengthened by increasing plate-like NN. → k p and d 33 decrease with increasing amount of plate-like NN. → 0.01-0.03 mol of plate-like NN is a proper content for texturing ceramics by RTGG. - Abstract: Plate-like NaNbO 3 (NN) particles were used as the raw material to fabricate (1 - x)[0.93 K 0.48 Na 0.52 Nb O 3 -0.07Li(Ta 0.5 Nb 0.5 )O 3 ]-xNaNbO 3 lead-free piezoelectric ceramics using a conventional ceramic process. The effects of NN on the crystal structure and piezoelectric properties of the ceramics were investigated. The results of X-ray diffraction suggest that the perovskite phase coexists with the K 3 Li 2 Nb 5 O 15 phase, and the tilting of the oxygen octahedron is probably responsible for the evolution of the tungsten-bronze-typed K 3 Li 2 Nb 5 O 15 phase. The Curie temperature (T C ) is shifted to lower temperature with increasing NN content. (1 - x)[0.93 K 0.48 Na 0.52 NbO 3 -0.07Li(Ta 0.5 Nb 0.5 )O 3 ]-xNaNbO 3 ceramics show obvious dielectric relaxor characteristics for x > 0.03, and the relaxor behavior of ceramics is strengthened by increasing NN content. Both the electromechanical coupling factor (k p ) and the piezoelectric constant (d 33 ) decrease with increasing amounts of NN. 0.01-0.03 mol of plate-like NaNbO 3 in 0.93 K 0.48 Na 0.52 NbO 3 -0.07Li(Ta 0.5 Nb 0.5 )O 3 gives the optimum content for preparing textured ceramics by the RTGG method.

High-temperature fracture and fatigue resistance of a ductile β-TiNb reinforced γ-TiAl intermetallic composite

International Nuclear Information System (INIS)

Rao, K.T.V.; Ritchie, R.O.

1998-01-01

The high-temperature fatigue-crack propagation and fracture resistance of a model γ-TiAl intermetallic composite reinforced with 20 vol. % ductile β-TiNb particles is examined at elevated temperatures of 650 and 800 C and compared with behavior at room temperature. TiNb reinforcements are found to enhance the fracture toughness of γ-TiAl, even at high temperatures, from about 123 to ∼40 MPa m 1/2 , although their effectiveness is lower compared to room temperature due to the reduction in strength of TiNb particles. Under monotonic loading, crack-growth response in the composite is characterized by resistance-curve behavior arising from crack trapping, renucleation and resultant crack bridging effects attributable to the presence of TiNb particles. In addition, crack-tip blunting associated with plasticity increases the crack-initiation (matrix) toughness of the composite, particularly at 800 C, above the ductile-to-brittle transition temperature (DBTT) for γ-TiAl. High-temperature fatigue-crack growth resistance, however, is marginally degraded by the addition of TiNb particles in the C-R (edge) orientation, similar to observations made at room temperature; premature fatigue failure of TiNb ligaments in the crack wake diminishes the role of bridging under cyclic loading. Both fatigue and fracture resistance of the composite are slightly lower at 650 C (just below the DBTT for TiAl) compared to the behavior at ambient and 800 C. Overall, the beneficial effect of adding ductile TiNb reinforcements to enhance the room-temperature fracture and fatigue resistance of γ-TiAl alloys is retained up to 800 C, in air environments. There is concern, however, regarding the long-term environmental stability of these composite microstructures in unprotected atmospheres

Combined TiN- and TaN temperature compensated thin film resistors

International Nuclear Information System (INIS)

Malmros, Anna; Andersson, Kristoffer; Rorsman, Niklas

2012-01-01

The opposite signs of the temperature coefficient of resistance (TCR) of two thin film materials, titanium nitride (TiN) and tantalum nitride (TaN), were used to form temperature compensated thin film resistors (TFRs). The principle of designing temperature compensated TFRs by connecting TFRs of each compound in series or in parallel was demonstrated. TiN, TaN, and combined TiN and TaN TFRs for monolithic microwave integrated circuits (MMICs) were fabricated by reactive sputtering. DC characterization was performed over the temperature range of 30–200 °C. The TiN TFRs exhibited an increase in resistivity with temperature with TCRs of 540 and 750 ppm/°C. The TaN TFR on the other hand exhibited a negative TCR of − 470 ppm/°C. The shunted TFRs were fabricated by serial deposition of TiN and TaN to form a bilayer component. The TCRs of the series- and shunt configurations were experimentally reduced to − 60 and 100 ppm/°C, respectively. The concept of temperature compensation was used to build a Wheatstone bridge with an application in on-chip temperature sensing.

Characterisation and dissolution studies on the uranium pyrochlore mineral betafite (Ca,U)_2(Nb,Ti,Ta)_2O_7

International Nuclear Information System (INIS)

McMaster, S.; Ram, R.; Tardio, J.; Bhargava, S.

2014-01-01

The pyrochlore group mineral, betafite (nominally (Ca,U)_2(Nb,Ti,Ta)_2O_7); is a refractory uranium mineral found in many ore deposits, including the currently mined deposit at Rössing, Namibia and the currently unmined deposit at Saima Massif, China. The decreasing abundance of “easy to leach” uranium minerals (i.e. uraninite), has led to interest in the extraction of uranium from refractory uranium minerals such as betafite. In the current study, three naturally occurring betafite mineral samples (obtained from Ambatofotsky and Miarinarivo, Madagascar (BAM and BMM respectively) and Silver Crater Mine, Canada (BSC)) were characterised using ex-situ high temperature X-Ray Diffraction (XRD), multi acid digestion / ICP-MS analysis (composition) and X-Ray Photoelectron Spectroscopy (XPS). Dissolution of the three samples was also investigated under conditions similar to those used in commercial tank based uranium leaching processes. XRD analysis showed that all three samples were highly metamict. Samples BMM and BSC showed no assignable diffraction lines before heat treating, whereas the XRD pattern obtained for sample BAM contained diffraction lines that confirmed the presence of crystalline anatase (TiO_2). Heat treatment studies on the samples showed that the betafite in the samples was converted into a crystalline form at 700°C in all 3 samples. Gangue minerals, rutile, Nb-rutile, UTiNb_2O_1_0, and studitite were also found to be present in the heat treated samples. Multi acid digestion ICP-MS analysis showed the natural samples contained between 16 and 26% w/w uranium as well as all the major elements present typically in betafite. XPS analysis was conducted on the unheated betafite samples. XPS analysis showed that the uranium in the samples was predominately in U"5"+ oxidation state. Some U"6"+ was also identified though this was most likely restricted to the outer surface of the samples. Dissolution studies (batch mode) were conducted under the following

Perovskite-related Ca(Nb,Ti)O3.33

International Nuclear Information System (INIS)

Guevarra, J.; Smaalen, S. van; Daniels, P.; Rotiroti, N.; Lichtenberg, F.

2005-01-01

Crystals of nominal composition Ca(Nb 0.8 Ti 0.2 )O 3.4 , an n = 5 member of the homologous series A n B n O 3n+2 , have been synthesized by floating-zone melting. The material was found to be multiphase consisting also of the n = 6 type. A good single crystal of this n = 6 type was found and the crystal structure at room temperature was determined by X-ray diffraction using synchrotron radiation. Structure refinements indicate a composition of Ca(Nb 0.76 Ti 0.24 )O 3.33 . The crystal structure is monoclinic P2 1 and consists of slabs of corner-sharing (Nb,Ti)O 6 octahedra interrupted by layers of oxygen atoms. Ca atoms within the slabs are 12-fold coordinated whereas those at the borders show irregular coordination geometries. The octahedral distortion is greatest near the borders of the slabs and least near the middle of the slabs. Ti 4+ preferentially occupy octahedral sites in the middle of slabs. The non-stoichiometry in the refined composition and the insulating character of the material may be explained in terms of extra oxygen, vacancies on the cation sites, or by localization of the electrons in the 4d orbitals of Nb at the borders of slabs. (orig.)

Transport measurements in superconductor/Heusler bilayers

Energy Technology Data Exchange (ETDEWEB)

Imort, Inga-Mareen; Fabretti, Savio; Thomas, Patrick; Reiss, Guenter; Thomas, Andy [Fakultaet fuer Physik, Universitaet Bielefeld, Bielefeld (Germany)

2012-07-01

Superconductivity and ferromagnetism are two contrary phenomena due to their electronic properties. The investigation of superconductor (S)/ferromagnet (F) heterostructures has attracted a lot of scientific interest since they allow studying the interplay between superconductivity and ferromagnetism. Additionally, applications seem possible such as F/S/F spin valves and S/F/S π-junctions. Using transport- and magnetotransport-measurements, we investigate the behavior of the superconducting transition temperature T{sub c} in NbTi/Co{sub 2}FeSi bilayers as a function of different layer thicknesses and for varying magnetic moments of the Co{sub 2}FeSi layers. Using rf-magnetron sputtering, NbTi/Co{sub 2}FeSi bilayers were grown on single-crystalline MgO(001) substrates and in-situ annealed at different temperatures. The layered character of our samples has been tested by X-ray diffraction (XRD) scans. The electronic and magnetic transport measurements have been performed between 3 and 300 K with the magnetic field up to 4 T oriented in the film plane. The dependence of T{sub c} on the NbTi- and Co{sub 2}FeSi-layer thickness enables an estimation of the interface transparency of the NbTi/Co{sub 2}FeSi barrier in the framework of recent theoretical models.

Multi-component solid solution alloys having high mixing entropy

Science.gov (United States)

Bei, Hongbin

2015-10-06

A multi-component high-entropy alloy includes a composition selected from the following group: VNbTaTiMoWRe, VNbTaTiMoW, VNbTaTiMoRe, VNbTaTiWRe, VNbTaMoWRe, VNbTiMoWRe, VTaTiMoWRe, NbTaTiMoWRe, VNbTaTiMo, VNbTaTiW, VNbTaMoW, VNbTiMoW, VTaTiMoW, NbTaTiMoW, VNbTaTiRe, VNbTaMoRe, VNbTiMoRe, VTaTiMoRe, NbTaTiMoRe, VNbTaWRe, VNbTiWRe, VTaTiWRe, NbTaTiWRe, VNbMoWRe, VTaMoWRe, NbTaMoWRe, VTiMoWRe, NbTiMoWRe, TaTiMoWRe, wherein relative amounts of each element vary by no more than .+-.15 atomic %.

Epitaxial NbN/AlN/NbN tunnel junctions on Si substrates with TiN buffer layers

Directory of Open Access Journals (Sweden)

Rui Sun

2016-06-01

Full Text Available We have developed epitaxial NbN/AlN/NbN tunnel junctions on Si (100 substrates with a TiN buffer layer. A 50-nm-thick (200-oriented TiN thin film was introduced as the buffer layer for epitaxial growth of NbN/AlN/NbN trilayers on Si substrates. The fabricated NbN/AlN/NbN junctions demonstrated excellent tunneling properties with a high gap voltage of 5.5 mV, a large IcRN product of 3.8 mV, a sharp quasiparticle current rise with a ΔVg of 0.4 mV, and a small subgap leakage current. The junction quality factor Rsg/RN was about 23 for the junction with a Jc of 47 A/cm2 and was about 6 for the junction with a Jc of 3.0 kA/cm2. X-ray diffraction and transmission electron microscopy observations showed that the NbN/AlN/NbN trilayers were grown epitaxially on the (200-orientated TiN buffer layer and had a highly crystalline structure with the (200 orientation.

Epitaxial NbN/AlN/NbN tunnel junctions on Si substrates with TiN buffer layers

Energy Technology Data Exchange (ETDEWEB)

Sun, Rui [State Key Laboratory of Functional Materials for Informatics, Shanghai Institute of Microsystem and Information Technology (SIMIT), Chinese Academy of Sciences (CAS), Shanghai 200050 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Makise, Kazumasa; Terai, Hirotaka [Advanced ICT Research Institute, National Institute of Information and Communications Technology (Japan); Zhang, Lu [State Key Laboratory of Functional Materials for Informatics, Shanghai Institute of Microsystem and Information Technology (SIMIT), Chinese Academy of Sciences (CAS), Shanghai 200050 (China); Wang, Zhen, E-mail: zwang@mail.sim.ac.cn [State Key Laboratory of Functional Materials for Informatics, Shanghai Institute of Microsystem and Information Technology (SIMIT), Chinese Academy of Sciences (CAS), Shanghai 200050 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Shanghai Tech University, Shanghai 201210 (China)

2016-06-15

We have developed epitaxial NbN/AlN/NbN tunnel junctions on Si (100) substrates with a TiN buffer layer. A 50-nm-thick (200)-oriented TiN thin film was introduced as the buffer layer for epitaxial growth of NbN/AlN/NbN trilayers on Si substrates. The fabricated NbN/AlN/NbN junctions demonstrated excellent tunneling properties with a high gap voltage of 5.5 mV, a large I{sub c}R{sub N} product of 3.8 mV, a sharp quasiparticle current rise with a ΔV{sub g} of 0.4 mV, and a small subgap leakage current. The junction quality factor R{sub sg}/R{sub N} was about 23 for the junction with a J{sub c} of 47 A/cm{sup 2} and was about 6 for the junction with a J{sub c} of 3.0 kA/cm{sup 2}. X-ray diffraction and transmission electron microscopy observations showed that the NbN/AlN/NbN trilayers were grown epitaxially on the (200)-orientated TiN buffer layer and had a highly crystalline structure with the (200) orientation.

Measuring the microwave response of superconducting Nb:STO and Ti at mK temperatures using superconducting resonators

Energy Technology Data Exchange (ETDEWEB)

Thiemann, Markus; Beutel, Manfred; Dressel, Martin; Scheffler, Marc [1. Physikalisches Institut, Universitaet Stuttgart (Germany); Fillis-Tsirakis, Evangelos; Boschker, Hans; Mannhart, Jochen [Max Planck Institute for Solid State Research, Stuttgart (Germany)

2016-07-01

Niobium doped SrTiO{sub 3} is a superconductor, with the lowest charge carrier density among all superconductors. It shows a dome in the transition temperature as a function of doping concentration with a maximum T{sub c} ∼ 0.3 K. The superconducting dome may originate from the different bands being occupied depending on the doping level. The low energy scales of the system, as indicated by the low T{sub c} are within the GHz-regime. Therefore microwave measurements are a powerful technique to reveal the electronic properties of these superconductors. We preformed microwave measurements on Nb:STO of different doping levels in a dilution refrigerator, using superconducting stripline resonators. Measurements were done in a temperature and frequency range from 40-400 mK and 1-20 GHz, covering the normal and superconducting states. For comparison we also measured the temperature dependence of the surface impedance of superconducting titanium (T{sub c} ∼ 0.5 K), which can be well described by the Mattis-Bardeen equations with a ratio (2Δ)/(k{sub B}T{sub c}) = 3.56. Therefore titanium is an ideal reference sample representing a conventional BCS-superconductor.

Development of Nb-Ti multifilamentar superconducting wires

International Nuclear Information System (INIS)

Otubo, J.

1986-01-01

Ni-Ti superconducting wires with multifilamentar configuration were produced, using the grouping technique. Some basic concepts on superconductivity and its main critical parameters are presented. The criteria for stabilizing superconductors in terms of the geometry are studied. The main critical parameters, H c , J c , T c in function of the composition and the metallurgical structure of Ni-Ti alloy are analysed. The development of Ni-Ti superconducting wires is described. (M.C.K.) [pt

Beta Ti-45Nb and Ti-50Nb alloys produced by powder metallurgy for aerospace application

Energy Technology Data Exchange (ETDEWEB)

Martins, G.V.; Trava-Airoldi, V.J.; Machado, J.P.B., E-mail: givmartins@yahoo.com.br, E-mail: vladimir@las.inpe.br, E-mail: joaopaulo@las.inpe.br [Instituto Nacional de Pesquisas Espaciais (INPE), Sao Jose dos Campos, SP (Brazil); Silva, C.R.M., E-mail: cosmeroberto@gmail.com [Universidade de Brasilia (UnB), Brasilia, DF (Brazil); Nunes, C.A., E-mail: cnunes@demar.eel.usp.br [Universidade de Sao Paulo (EEL/USP), Lorena, SP (Brazil). Polo Urbo Industrial; Borges Junior, L.A., E-mail: borges.jr@itelefonica.com.br [Centro Universitario de Volta Redond (UNIFOA), Volta Redonda, RJ (Brazil)

2009-07-01

Beta titanium alloys parts are used on advanced aerospace systems because of their high strength to weight ratio and excellent corrosion resistance. Production of powder metallurgy titanium alloys components may lead to a substantial reduction in the cost, compared to those produced by conventional cast and wrought processes, because additional working operations and material waste can be avoided. In this work, beta Ti-45Nb and Ti- 50Nb were produced by the blended elemental technique, followed by uniaxial and cold isostatic pressing with subsequent densification by sintering. Sintered samples were characterized for phase composition by XRD, microstructure by SEM, hardness by Vickers indentation, specific mass by the Archimedes method and elastic modulus by resonance ultrasound. The sintered samples presented only the beta phase, higher hardness and lower elastic modulus when compared to Ti6Al4V alloy and experimental specific mass value near theoretical specific mass. These characteristics are adequate for application on several aerospace parts. (author)

Beta Ti-45Nb and Ti-50Nb alloys produced by powder metallurgy for aerospace application

International Nuclear Information System (INIS)

Martins, G.V.; Trava-Airoldi, V.J.; Machado, J.P.B.; Silva, C.R.M.; Nunes, C.A.

2009-01-01

Beta titanium alloys parts are used on advanced aerospace systems because of their high strength to weight ratio and excellent corrosion resistance. Production of powder metallurgy titanium alloys components may lead to a substantial reduction in the cost, compared to those produced by conventional cast and wrought processes, because additional working operations and material waste can be avoided. In this work, beta Ti-45Nb and Ti- 50Nb were produced by the blended elemental technique, followed by uniaxial and cold isostatic pressing with subsequent densification by sintering. Sintered samples were characterized for phase composition by XRD, microstructure by SEM, hardness by Vickers indentation, specific mass by the Archimedes method and elastic modulus by resonance ultrasound. The sintered samples presented only the beta phase, higher hardness and lower elastic modulus when compared to Ti6Al4V alloy and experimental specific mass value near theoretical specific mass. These characteristics are adequate for application on several aerospace parts. (author)

Multiscale simulation of mechanical properties of TiNb alloy

Science.gov (United States)

Nikonov, A. Yu.

2017-12-01

The article presents a numerical simulation of the mechanical properties of a Ti-Nb β-alloy on three different scales. The ab-initio approach is used to estimate the concentrations of the Ti alloy with required elastic properties. On the basis of molecular dynamics simulation, we calculate the adhesive force between individual particles of the alloy. The calculated dependence is implemented within the movable cellular automata method to determine the mechanical properties of Ti-Nb depending on the interparticle free space.

Shape-memory effect in Ti-Nb alloys

International Nuclear Information System (INIS)

Peradze, T.; Berikashvili, T.; Chelidze, T.; Gorgadze, K.; Bochorishvili, M.; Taktakishvili, M.

2009-01-01

The work deals with the investigation of the binary alloy of titanium with niobium and is aimed at demonstrating the functional-mechanical possibilities of Ti-Nb alloys from the viewpoint of their potential application in practice. The shape-memory effect, super elasticity and reactive stress in alloys of Ti-Nb system were studied. It turned out that the work carried out expanded the interval of Nb content in the investigated alloys from 25.9 to 33.1 wt%. The shape recovery made up not less than 90% at the deformation of 6-8%. The reactive stress reached 350-450 MPa. In the alloys under study another (high-temperature) shape-memory effect was found, and the influence of hydrogen and oxygen on the inelastic properties of alloys was studied. (author)

Effects of TiN coating on the corrosion of nanostructured Ti-30Ta-xZr alloys for dental implants

Science.gov (United States)

Kim, Won-Gi; Choe, Han-Cheol

2012-01-01

Electrochemical characteristics of a titanium nitride (TiN)-coated/nanotube-formed Ti-Ta-Zr alloy for biomaterials have been researched by using the magnetic sputter and electrochemical methods. Ti-30Ta-xZr (x = 3, 7 and 15 wt%) alloys were prepared by arc melting and heat treated for 24 h at 1000 °C in an argon atmosphere and then water quenching. The formation of oxide nanotubes was achieved by anodizing a Ti-30Ta-xZr alloy in H3PO4 electrolytes containing small amounts of fluoride ions at room temperature. Anodization was carried out using a scanning potentiostat, and all experiments were conducted at room temperature. The microstructure and morphology of nanotube arrays were characterized by optical microscopy (OM), field emission scanning electron microscopy (FE-SEM) and X-ray diffraction (XRD). The TiN coatings were obtained by the radio-frequency (RF) magnetron sputtering technique. The depositions were performed from pure Ti targets on Ti-30Ta-xZr alloys substrates. The corrosion properties of the specimens were examined using potentiodynamic test in a 0.9% NaCl solution by using potentiostat. The microstructures of Ti-30Ta-xZr alloys were changed from an equiaxed to a needle-like structure with increasing Zr content. The interspace between the nanotubes was approximately 20, 80 and 200 nm for Zr contents of 3, 7 and 15 wt%, respectively. The corrosion resistance of the TiN-coated on the anodized Ti-30Ta-xZr alloys was higher than that of the untreated Ti alloys, indicating a better protective effect.

Effects of differential thermal contraction between the matrix and the filaments in mono- and multifilamentary Nb3Sn on the superconducting critical temperature

International Nuclear Information System (INIS)

Aihara, K.; Suenage, M.; Luhman, T.

1979-01-01

The strain on Nb 3 Sn due to the differential thermal contraction between the matrix (Cu, bronze) and the filaments (Nb, Nb 3 Sn, Ta) of a superconducting wire is known to decrease the superconducting critical temperature T/sub c/. In order to study the effects of heat treatment conditions and filament size on the degradation of T/sub c/ by the strain. T/sub c/ for monofilamentary wires [(Nb 3 Sn and bronze in Ta) in Cu matrix, and (bronze in Nb tubings) in Cu matrix] were measured for heat-treating periods in of 1 to 120 h at 725 0 C. Several observations were made regarding the effects on T/sub c/ of thermal contraction strains from various components of the conductors. The influence of a Cu matrix on T/sub c/ was small (approx. 0.2 K). When the bronze matrix was inside Nb tubing the degradation of T/sub c/ due to strains was substantially larger than when the Nb filaments were in a bronze. Wires with smaller filament diameters achieved a maximum T/sub c/ in shorter heat treatment times than those with larger filaments. These results are discussed in terms of the critical currents of these wires under applied tensile strains

Structural and vibrational investigations of Nb-doped TiO2 thin films

International Nuclear Information System (INIS)

Uyanga, E.; Gibaud, A.; Daniel, P.; Sangaa, D.; Sevjidsuren, G.; Altantsog, P.; Beuvier, T.; Lee, Chih Hao; Balagurov, A.M.

2014-01-01

Highlights: • We studied the evolutions of structure for TiO 2 thin film as changes with Nb doping and temperatures. • Up to 800 °C, the grain size of Nb 0.1 Ti 0.9 O 2 is smaller than for pure TiO 2 because doped Nb hinders the growth of the TiO 2 grains. • There was no formation of the rutile phase at high temperature. • Nb doped TiO 2 films have high electron densities at 400–700 °C. • Nb dope extends the absorbance spectra of TiO 2 which leads to the band gap reduce. - Abstract: Acid-catalyzed sol–gel and spin-coating methods were used to prepare Nb-doped TiO 2 thin film. In this work, we studied the effect of niobium doping on the structure, surface, and absorption properties of TiO 2 by energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), X-ray reflectometry (XRR), X-ray photoelectron spectroscopy (XPS), Raman, and UV–vis absorption spectroscopy at various annealing temperatures. EDX spectra show that the Nb:Ti atomic ratios of the niobium-doped titania films are in good agreement with the nominal values (5 and 10%). XPS results suggest that charge compensation is achieved by the formation of Ti vacancies. Specific niobium phases are not observed, thus confirming that niobium is well incorporated into the titania crystal lattice. Thin films are amorphous at room temperature and the formation of anatase phase appeared at an annealing temperature close to 400 °C. The rutile phase was not observed even at 900 °C (XRD and Raman spectroscopy). Grain sizes and electron densities increased when the temperature was raised. Nb-doped films have higher electron densities and lower grain sizes due to niobium doping. Grain size inhibition can be explained by lattice stress induced by the incorporation of larger Nb 5+ ions into the lattice. The band gap energy of indirect transition of the TiO 2 thin films was calculated to be about 3.03 eV. After niobium doping, it decreased to 2.40 eV

Effect of Ta substitution method on the mechanical properties of Ni3(Si,Ti) intermetallic alloy

International Nuclear Information System (INIS)

Imajo, Daiki; Kaneno, Yasuyuki; Takasugi, Takayuki

2013-01-01

In this study, Ta was added to an L1 2 -type Ni 3 (Si,Ti) alloy at different levels and into different substitution sites, substituting for either Ni, Ti or Si. The solubility limits of Ta in the L1 2 phase were 1.9 at%, 5.7 at% and 1.0 at% when Ta substituted for Ni, Ti and Si, respectively. The lattice parameters in the L1 2 phase region increased in the order of the Ta(Ni)>Ta(Si)>Ta(Ti) quaternary alloys, in which Ta substituted for Ni, Si and Ti, respectively. The room-temperature hardness in the L1 2 phase region increased linearly with increasing Ta content, and the increment rate increased in the order of the Ta(Ni)>Ta(Si)>Ta(Ti) quaternary alloys. Similarly, the room-temperature 0.2% proof stress as well as the tensile strength in the L1 2 phase region increased linearly with increasing Ta content, and the increment rate increased in the order of the Ta(Ni)>Ta(Si)>Ta(Ti) quaternary alloys. High tensile elongation was observed at room temperature when the microstructures remain in the L1 2 single phase. At high temperatures, a positive temperature dependence of the hardness as well as the flow strength was observed in the quaternary alloys. It was also shown that the wear resistance of the quaternary Ta(Ti) alloys was improved and attributed to plastically induced hardening of the worn surfaces combined with the positive temperature dependence of the flow strength. The strengthening and hardening resulting from Ta addition was suggested to be due to the hardening of the solid solution arising from the misfits in the atomic radius between Ta and the constituent atoms Ni, Ti or Si

On the role of Nb-related sites of an oxidized β-TiNb alloy surface in its interaction with osteoblast-like MG-63 cells

Energy Technology Data Exchange (ETDEWEB)

Jirka, Ivan, E-mail: Ivan.Jirka@jh-inst.cas.cz [J. Heyrovský Institute of Physical Chemistry, Acad. Sci. CR, v.v.i. Dolejškova 3, 182 23 Prague 8 (Czech Republic); Vandrovcová, Marta [Institute of Physiology, Acad. Sci. CR, v.v.i., Vídeňská 1083, Prague 4 (Czech Republic); Frank, Otakar [J. Heyrovský Institute of Physical Chemistry, Acad. Sci. CR, v.v.i. Dolejškova 3, 182 23 Prague 8 (Czech Republic); Tolde, Zdeněk [Faculty of Mechanical Engineering, Czech Technical University in Prague, Institute of Materials Engineering, Karlovo nám. 13, Prague 2 (Czech Republic); Plšek, Jan [J. Heyrovský Institute of Physical Chemistry, Acad. Sci. CR, v.v.i. Dolejškova 3, 182 23 Prague 8 (Czech Republic); Luxbacher, Thomas [Anton Paar GmbH, Anton Paar Str. 20, 8054 Graz (Austria); Bačáková, Lucie [Institute of Physiology, Acad. Sci. CR, v.v.i., Vídeňská 1083, Prague 4 (Czech Republic); Starý, Vladimír [Faculty of Mechanical Engineering, Czech Technical University in Prague, Institute of Materials Engineering, Karlovo nám. 13, Prague 2 (Czech Republic)

2013-04-01

β-Stabilized titanium (Ti) alloys containing non-toxic elements, particularly niobium (Nb), are promising materials for the construction of bone implants. Their biocompatibility can be further increased by oxidation of their surface. Therefore, in this study, the adhesion, growth and viability of human osteoblast-like MG 63 cells in cultures on oxidized surfaces of a β-TiNb alloy were investigated and compared with the cell behavior on thermally oxidized Ti, i.e. a metal commonly used for constructing bone implants. Four experimental groups of samples were prepared: Ti or TiNb samples annealed to 600 °C for 60 min in a stream of dry air, and Ti and TiNb samples treated in Piranha solution prior to annealing. We found that on all TiNb-based samples, the cell population densities on days 1, 3 and 7 after seeding were higher than on the corresponding Ti-based samples. As revealed by XPS and Raman spectroscopy, and also by isoelectric point measurements, these results can be attributed to the presence of T-Nb{sub 2}O{sub 5} oxide phase in the surface of the alloy sample, which decreased its negative zeta (ζ)-potential in comparison with zeta (ζ)-potential of the Ti sample at physiological pH. This effect was tentatively explained by the presence of positively charged defects acting as Lewis sites of the surface Nb{sub 2}O{sub 5} phase. Piranha treatment slightly decreases the biocompatibility of the samples, which for the alloy samples may be explained by a decrease in the number of defective sites with this treatment. Thus, the presence of Nb and thermal oxidation of β-stabilized Ti alloys play a significant role in the increased biocompatibility of TiNb alloys. - Highlights: ► T-Nb{sub 2}O{sub 5} and rutile are the main components of the oxidized β-TiNb alloy surface. ► Negative value of ζ potential is reduced by presence of Nb in the alloy surface. ► Less negative ζ potential is beneficial for interaction of the alloy with cells. ► The β-TiNb alloy

Novel transparent conducting oxide: Anatase Ti1-xNb xO2

International Nuclear Information System (INIS)

Furubayashi, Yutaka; Hitosugi, Taro; Yamamoto, Yukio; Hirose, Yasushi; Kinoda, Go; Inaba, Kazuhisa; Shimada, Toshihiro; Hasegawa, Tetsuya

2006-01-01

Single-crystalline Ti 1-x Nb x O 2 (x = 0.2) films of 40 nm thickness were deposited on SrTiO 3 (100) substrates by the pulsed laser deposition (PLD) technique. X-ray diffraction measurement confirmed epitaxial growth of anatase (001) film. The resistivity of Ti 1-x Nb x O 2 films with x ≥ 0.03 is 2-3 x 10 -4 Ω cm at room temperature. The carrier density of Ti 1-x Nb x O 2 , which is almost proportional to the Nb concentration, can be controlled in a range of 1 x 10 19 to 2 x 10 21 cm -3 . Optical measurements revealed that internal transmittance in the visible and near-infrared region for films with x = 0.03 was more than 97%. These results demonstrate that the presently developed anatase Ti 1-x Nb x O 2 is one of the promising candidates for the practical TCOs

Nb-doped rutile TiO₂: a potential anode material for Na-ion battery.

Science.gov (United States)

Usui, Hiroyuki; Yoshioka, Sho; Wasada, Kuniaki; Shimizu, Masahiro; Sakaguchi, Hiroki

2015-04-01

The electrochemical properties of the rutile-type TiO2 and Nb-doped TiO2 were investigated for the first time as Na-ion battery anodes. Ti(1-x)Nb(x)O2 thick-film electrodes without a binder and a conductive additive were prepared using a sol-gel method followed by a gas-deposition method. The TiO2 electrode showed reversible reactions of Na insertion/extraction accompanied by expansion/contraction of the TiO2 lattice. Among the Ti(1-x)Nb(x)O2 electrodes with x = 0-0.18, the Ti(0.94)Nb(0.06)O2 electrode exhibited the best cycling performance, with a reversible capacity of 160 mA h g(-1) at the 50th cycle. As the Li-ion battery anode, this electrode also attained an excellent rate capability, with a capacity of 120 mA h g(-1) even at the high current density of 16.75 A g(-1) (50C). The improvements in the performances are attributed to a 3 orders of magnitude higher electronic conductivity of Ti(0.94)Nb(0.06)O2 compared to that of TiO2. This offers the possibility of Nb-doped rutile TiO2 as a Na-ion battery anode as well as a Li-ion battery anode.

Flux Pinning in Superconductors

CERN Document Server

Matsushita, Teruo

2007-01-01

The book covers the flux pinning mechanisms and properties and the electromagnetic phenomena caused by the flux pinning common for metallic, high-Tc and MgB2 superconductors. The condensation energy interaction known for normal precipitates or grain boundaries and the kinetic energy interaction proposed for artificial Nb pins in Nb-Ti, etc., are introduced for the pinning mechanism. Summation theories to derive the critical current density are discussed in detail. Irreversible magnetization and AC loss caused by the flux pinning are also discussed. The loss originally stems from the ohmic dissipation of normal electrons in the normal core driven by the electric field induced by the flux motion. The readers will learn why the resultant loss is of hysteresis type in spite of such mechanism. The influence of the flux pinning on the vortex phase diagram in high Tc superconductors is discussed, and the dependencies of the irreversibility field are also described on other quantities such as anisotropy of supercondu...

Crystal structure and X-ray photoemission spectroscopic study of A{sub 2}LaMO{sub 6} [A=Ba, Ca; M=Nb, Ta

Energy Technology Data Exchange (ETDEWEB)

Dutta, Alo, E-mail: alo_dutta@yahoo.com [Department of Condensed Matter Physics and Material Sciences, S. N. Bose National Centre for Basic Sciences, Block-JD, Sector-III, Salt Lake, Kolkata 700098 (India); Saha, Sujoy [Department of Physics, Bose Institute, 93/1 Acharya Prafulla Chandra Road, Kolkata 700009 (India); Kumari, Premlata [Department of Chemistry, Government P.G. College, Lansdowne, Pauri-Garhwal 246139 (India); Sinha, T.P. [Department of Physics, Bose Institute, 93/1 Acharya Prafulla Chandra Road, Kolkata 700009 (India); Shannigrahi, Santiranjan [Institute of Materials Research and Engineering, Agency for Science Technology and Research, 3 Research Link, Singapore 117602 (Singapore)

2015-09-15

The X-ray photoemission spectroscopic (XPS) study of the double perovskite oxides A{sub 2}LaMO{sub 6} [A=Ba, Ca; M=Nb, Ta] synthesized by the solid-state reaction technique has been carried out to investigate the nature of the chemical state of the constituent ions and the bonding between them. The Rietveld refinement of the X-ray diffraction patterns suggests the monoclinic crystal structure of all the materials at room temperature. The negative and positive chemical shifts of the core level XPS spectrum of O-1s and Nb-3d{sub 3/2}/Ta-4f{sub 5/2} respectively suggest the covalent bonding between Nb/Ta cations and O ion. The change of the bonding strength between the anion and the cations from one material to another has been analyzed. The vibrational property of the materials is investigated using the room temperature Raman spectra. A large covalency of Ta-based compound than Nb compound is confirmed from the relative shifting of the Raman modes of the materials. - Graphical abstract: Crystal structure of two perovskite oxides CLN and CLT is investigated. XPS study confirms the two different co-ordination environments of Ca and covalent bonding between B-site cations and O-ion. - Highlights: • Ordered perovskite structure obtained by Rietveld refinement of XRD patterns. • Study of nature of chemical bonding by X-ray photoemission spectroscopy. • Opposite chemical shift of d-states of Nb/Ta with respect to O. • Covalent bonding between d-states of Nb/Ta and O. • Relative Raman shifts of CLN and CLT substantiate the more covalent character of Ta than Nb.

Promising Ta-Ti-Zr-Si metallic glass coating without cytotoxic elements for bio-implant applications

Science.gov (United States)

Lai, J. J.; Lin, Y. S.; Chang, C. H.; Wei, T. Y.; Huang, J. C.; Liao, Z. X.; Lin, C. H.; Chen, C. H.

2018-01-01

Tantalum (Ta) is considered as one of the most promising metal due to its high corrosion resistance, excellent biocompatibility and cell adhesion/in-growth capabilities. Although there are some researches exploring the biomedical aspects of Ta and Ta based alloys, systematic characterizations of newly developed Ta-based metallic glasses in bio-implant applications is still lacking. This study employs sputtering approach to produced thin-film Ti-based metallic glasses due to the high melting temperature of Ta (3020 °C). Two fully amorphous Ta-based metallic glasses composed of Ta57Ti17Zr15Si11 and Ta75Ti10Zr8Si7 are produced and experimentally characterized in terms of their mechanical properties, bio-corrosion properties, surface hydrophilic characteristics, and in-vitro cell viability and cells attachment tests. Compare to conventional pure Ti and Ta metals, the developed Ta-based metallic glasses exhibit higher hardness and lower modulus which are better match to the mechanical properties of bone. MTS assay results show that Ta-based metallic glasses show comparable cell viability and cell attachment rate compared to that of pure Ti and Ta surface in a 72 h in-vitro test.

Effects of a Ta interlayer on the phase transition of TiSi2 on Si(111)

Science.gov (United States)

Jeon, Hyeongtag; Jung, Bokhee; Kim, Young Do; Yang, Woochul; Nemanich, R. J.

2000-09-01

This study examines the effects of a thin Ta interlayer on the formation of TiSi2 on Si(111) substrate. The Ta interlayer was introduced by depositing Ta and Ti films sequentially on an atomically clean Si(111) substrate in an ultrahigh vacuum (UHV) system. Samples of 100 Å Ti with 5 and 10 Å Ta interlayers were compared to similar structures without an interlayer. After deposition, the substrates were annealed for 10 min, in situ, at temperatures between 500 and 750 °C in 50 °C increments. The TiSi2 formation with and without the Ta interlayer was analyzed with an X-ray diffractometer, Auger electron spectroscopy (AES), Scanning electron microscopy (SEM), transmission electron microscopy (TEM), and a four-point probe. The AES analysis data showed a 1:2 ratio of Ti:Si in the Ti-silicide layer and indicated that the Ta layer remained at the interface between TiSi2 and the Si(111) substrate. The C 49-C 54 TiSi2 phase transition temperature was lowered by ˜200 °C. The C 49-C 54 TiSi2 phase transition temperature was 550 °C for the samples with a Ta interlayer and was 750 °C for the samples with no Ta interlayer. The sheet resistance of the Ta interlayered Ti silicide showed lower values of resistivity at low temperatures which indicated the change in phase transition temperature. The C 54 TiSi2 displayed different crystal orientation when the Ta interlayer was employed. The SEM and TEM micrographs showed that the TiSi2 with a Ta interlayer significantly suppressed the tendency to islanding and surface agglomeration.

The wheat NB-LRR gene TaRCR1 is required for host defence response to the necrotrophic fungal pathogen Rhizoctonia cerealis.

Science.gov (United States)

Zhu, Xiuliang; Lu, Chungui; Du, Lipu; Ye, Xingguo; Liu, Xin; Coules, Anne; Zhang, Zengyan

2017-06-01

The necrotrophic fungus Rhizoctonia cerealis is the major pathogen causing sharp eyespot disease in wheat (Triticum aestivum). Nucleotide-binding leucine-rich repeat (NB-LRR) proteins often mediate plant disease resistance to biotrophic pathogens. Little is known about the role of NB-LRR genes involved in wheat response to R. cerealis. In this study, a wheat NB-LRR gene, named TaRCR1, was identified in response to R. cerealis infection using Artificial Neural Network analysis based on comparative transcriptomics and its defence role was characterized. The transcriptional level of TaRCR1 was enhanced after R. cerealis inoculation and associated with the resistance level of wheat. TaRCR1 was located on wheat chromosome 3BS and encoded an NB-LRR protein that was consisting of a coiled-coil domain, an NB-ARC domain and 13 imperfect leucine-rich repeats. TaRCR1 was localized in both the cytoplasm and the nucleus. Silencing of TaRCR1 impaired wheat resistance to R. cerealis, whereas TaRCR1 overexpression significantly increased the resistance in transgenic wheat. TaRCR1 regulated certain reactive oxygen species (ROS)-scavenging and production, and defence-related genes, and peroxidase activity. Furthermore, H 2 O 2 pretreatment for 12-h elevated expression levels of TaRCR1 and the above defence-related genes, whereas treatment with a peroxidase inhibitor for 12 h reduced the resistance of TaRCR1-overexpressing transgenic plants and expression levels of these defence-related genes. Taken together, TaRCR1 positively contributes to defence response to R. cerealis through maintaining ROS homoeostasis and regulating the expression of defence-related genes. © 2016 The Authors. Plant Biotechnology Journal published by Society for Experimental Biology and The Association of Applied Biologists and John Wiley & Sons Ltd.

Development of superconductors for fusion technology

International Nuclear Information System (INIS)

Wilson, M.N.; Walters, C.R.

1976-04-01

A report is presented on the development of a 10 4 Amp NbTi cryogenically stabilized superconductor. The long term objective was the construction of a superconducting toroidal field magnet for a post JET Tokamak experiment. The report is in sections entitled: magnet reference parameters; specific conductor designs; theoretical studies; experimental measurements; fabrication techniques; discussion, summary, conclusions and recommendations. (U.K.)

In-Situ Neutron Diffraction Under Tensile Loading of Powder-in-Tube Cu/Nb$_{3}$Sn Composite Wires Effect of Reaction Heat Treatment on Texture, Internal Stress State and Load Transfer

CERN Document Server

Scheuerlein, C; Thilly, L

2007-01-01

The strain induced degradation of Nb$_{3}$Sn superconductors can hamper the performance of high field magnets. We report elastic strain measurements in the different phases of entire non-heat treated and fully reacted Nb$_{3}$Sn composite strands as a function of uniaxial stress during in-situ deformation under neutron beam. After the reaction heat treatment the Cu matrix loses entirely its load carrying capability and the applied stress is transferred to the remaining Nb-Ta alloy and to the brittle (Nb-Ta)3Sn phase, which exhibits a preferential grain orientation parallel to the strand axis.

Correlation between hardness and stress in Al-(Nb, Mo, Ta) thin films

Energy Technology Data Exchange (ETDEWEB)

Car, T., E-mail: car@irb.h [Rudjer Boskovic Institute, Division of Materials Science, Bijenicka cesta 54, 10000 Zagreb, P.O.B. 1016 (Croatia); Radic, N. [Rudjer Boskovic Institute, Division of Materials Science, Bijenicka cesta 54, 10000 Zagreb, P.O.B. 1016 (Croatia); Panjan, P.; Cekada, M. [Jozef Stefan Institute, Ljubljana (Slovenia); Tonejc, A. [Department of Physics, Bijenicka cesta 32, 10000 Zagreb, P.O.B. 331 (Croatia)

2009-06-30

The thin films of Al{sub x}Nb{sub 1-x} (95 {>=} x {>=} 20), Al{sub x}Mo{sub x} (90 {>=} x {>=} 20) and Al{sub x}Ta{sub 1-x} (95 {>=} x {>=} 20) were prepared by magnetron codeposition at room temperature. The average film thickness was from 325 to 400 nm, depending on the film composition. The structure of the as-deposited films was examined by the X-ray diffraction. The stress of the films was determined from the substrate deformation by the profilometer, and the microhardness (load 2 mN) was examined by the micro- and nano-hardness device. For the purpose of the examination of the hardness, the samples were deposited onto the sapphire wafers, while the examination of the film stress, was performed by using thin glass substrates. For all the Al-(Nb, Mo, Ta) alloy compositions, the microhardness is predominantly under the influence of the harder element, and monotonically decreases with the increase of the aluminum content. However, the microhardness of the amorphous AlTa films was higher than the bulk value of a harder element (Ta) in the alloy. A simple empirical linear relationship between the Vickers hardness, the bulk value hardness of the transition metal (harder element) and the elastic energy fraction of the identation deformation, was established. The elastic energy fraction in the microhardness is also linearly correlated with the stress in films.

Alternating magnetic field losses in ATLAS type aluminium stabilized NbTi superconductors

CERN Document Server

Boxman, E W; ten Kate, H H J

2002-01-01

During ramping up- and down of the current in large-scale magnets the ramp losses are an important factor affecting the thermal and electro-magnetic stability of the system. The calculation of the losses is not straightforward due to the large dimensions of the conductor (~600 mm/sup 2/) implying that diffusion effects have to be taken into account. The AC-losses of the Al stabilized NbTi cable conductors used in the ATLAS magnet system were measured in 0.5 m long samples, using an inductive method with pick-up coils as well as the calorimetric method. External varying magnetic fields up to 2 tesla amplitude were applied parallel and perpendicular to the conductor wide surface. The results are compared to theory. It is found that hysteresis loss, eddy current loss in the Aluminum cladding and cable-to-cladding coupling loss contribute most to the AC loss. (5 refs).

Superconductor-ferromagnet-superconductor nanojunctions from perovskite materials

International Nuclear Information System (INIS)

Štrbík, V.; Beňačka, Š.; Gaži, Š.; Španková, M.; Šmatko, V.; Knoška, J.; Gál, N.; Chromik, Š.; Sojková, M.; Pisarčík, M.

2017-01-01

Highlights: • Superconductor-ferromagnet-superconductor nanojunction. • Nanojunctions prepared by Ga"3"+ focused ion beam patterning. • Indication of triplet Cooper pair component in junction superconducting current. • Qualitative agreement with theoretical model. - Abstract: The lateral superconductor-ferromagnet–superconductor (SFS) nanojunctions based on high critical temperature superconductor YBa_2Cu_3O_x (YBCO) and half-metallic ferromagnet La_0_._6_7Sr_0_._3_3MnO_3 (LSMO) thin films were prepared to investigate a possible presence of long range triplet component (LRTC) of Cooper pairs in the LSMO. We applied Ga"3"+ focused ion beam patterning to create YBCO/LSMO/YBCO lateral type nanojunctions with LSMO length as small as 40 nm. The resistivity vs. temperature, critical current density vs. temperature and resistance vs. magnetic field dependence were studied to recognize the LRTC of Cooper pairs in the LSMO. A non-monotonic temperature dependence of junction critical current density and a decrease of the SFS nanojunction resistance in increased magnetic field were observed. Only weak manifestations of LRTC and some qualitative agreement with theory were found out in SFS nanojunctions realized from the perovskite materials. The presence of equal-spin triplet component of Cooper pairs in half-metallic LSMO ferromagnet is not such apparent as in SFS junctions prepared from low temperature superconductors NbTiN and half-metallic ferromagnet CrO_2.

Mechanical properties and biocompatibility in alloy Ti-Ta system containing oxygen; Propriedades mecanicas e biocompatibilidades em ligas do sistema Ti-Ta contendo oxigenio

Energy Technology Data Exchange (ETDEWEB)

Ruiz, S.L.M.; Grandini, C.R., E-mail: samlea@fc.unesp.b [Universidade Estadual Paulista (UNESP), Bauru, SP (Brazil). Lab. de Anelasticidade e Biomateriais; Claro, A.P.R.A. [Universidade Estadual Paulista Julio de Mesquisa Filho (DMT/UNESP), Guaratingueta, SP (Brazil). Fac. de Engenharia. Dept. de Materiais e Tecnologia

2010-07-01

Due to the excellent properties such as corrosion resistance, good mechanical strength/density, good performance at high temperatures, Ti is very useful in the chemical industry and aerospace. Currently, their use has expanded to the field of biomaterials, due to its excellent biocompatibility and reduced elasticity modulus, favouring the production of orthopaedic and dental prostheses. Promising alloys are the Ti-Ta system and researches have been directed to describe and understand the behavior of this system. In this paper, samples of Ti-Ta alloys containing 8 and 16% (wt%) containing interstitial oxygen were prepared and characterized by density, xray diffraction, hardness, elasticity modulus measurements and in vitro cytotoxicity tests. (author)

Carrier compensation mechanism in heavily Nb-doped anatase Ti{sub 1-x}Nb{sub x}O{sub 2+{delta}} epitaxial thin films

Energy Technology Data Exchange (ETDEWEB)

Nogawa, H; Chikamatsu, A; Hirose, Y; Hasegawa, T [Department of Chemistry, University of Tokyo, Tokyo 113-0033 (Japan); Nakao, S [Kanagawa Academy of Science and Technology (KAST), Kawasaki 213-0012 (Japan); Kumigashira, H; Oshima, M, E-mail: chikamatsu@chem.s.u-tokyo.ac.jp [Department of Applied Chemistry, University of Tokyo, Tokyo 113-8656 (Japan)

2011-09-14

We investigated the electronic structures of anatase Ti{sub 1-x}Nb{sub x}O{sub 2+{delta}} (TNO) thin films as a function of Nb concentration x using photoemission spectroscopy (PES) measurements to elucidate the origin of the abrupt decrease in carrier activation in heavily Nb-doped regime. The existing intensity ratio of Nb{sup 5+} evaluated from Nb 3d core-level PES spectra maintained a constant value of {approx}0.8 at x = 0.06-0.3, implying that electron carriers generated by Nb doping are compensated by p-type defects. Ti 2p-3d and O1s-2p resonant PES measurements of x = 0.06-0.3 films revealed that the in-gap states positioned {approx}1 eV below the Fermi level (E{sub F}) have a mixed character of Ti 3d and O 2p orbitals, whereas the states at E{sub F} mainly have a Ti 3d nature. We proposed a carrier compensation mechanism that interstitial oxygen atoms strongly combined with surrounding Nb atoms kill conduction electrons in heavily Nb-doped anatase TiO{sub 2}.

The effect of microstructure on the deformation modes and mechanical properties of Ti-6Al-2Nb-1Ta-0.8Mo: Part II. Equiaxed structures

Science.gov (United States)

Lin, Fu-Shiong; Starke, E. A.; Gysler, A.

1984-10-01

The Ti-6Al-2Nb-lTa-0.8Mo alloy was processed to develop both near-basal and transverse textures. Samples were annealed at different temperatures to vary the equiaxed alpha grain size and the thick-ness of the grain boundary beta, and subsequently quenched in order to transform the beta phase to either martensite, tempered martensite, or Widmanstätten alpha + beta. The effect of microstructure and texture on tensile properties and on fracture toughness was investigated. In addition, yield locus diagrams were constructed in order to study the texture strengthening effect. The yield strength was found to be strongly dependent on the thickness and Burgers relationship of the transformed beta phase surrounding the alpha grains. A texture hardening effect as large as 60 pct was found for the basal-texture material but only 15 pct for the transverse texture material. These variations are asso-ciated with differences in deformation behavior.

Effect of Ta substitution method on the mechanical properties of Ni{sub 3}(Si,Ti) intermetallic alloy

Energy Technology Data Exchange (ETDEWEB)

Imajo, Daiki; Kaneno, Yasuyuki; Takasugi, Takayuki, E-mail: takasugi@mtr.osakafu-u.ac.jp

2013-12-20

In this study, Ta was added to an L1{sub 2}-type Ni{sub 3}(Si,Ti) alloy at different levels and into different substitution sites, substituting for either Ni, Ti or Si. The solubility limits of Ta in the L1{sub 2} phase were 1.9 at%, 5.7 at% and 1.0 at% when Ta substituted for Ni, Ti and Si, respectively. The lattice parameters in the L1{sub 2} phase region increased in the order of the Ta(Ni)>Ta(Si)>Ta(Ti) quaternary alloys, in which Ta substituted for Ni, Si and Ti, respectively. The room-temperature hardness in the L1{sub 2} phase region increased linearly with increasing Ta content, and the increment rate increased in the order of the Ta(Ni)>Ta(Si)>Ta(Ti) quaternary alloys. Similarly, the room-temperature 0.2% proof stress as well as the tensile strength in the L1{sub 2} phase region increased linearly with increasing Ta content, and the increment rate increased in the order of the Ta(Ni)>Ta(Si)>Ta(Ti) quaternary alloys. High tensile elongation was observed at room temperature when the microstructures remain in the L1{sub 2} single phase. At high temperatures, a positive temperature dependence of the hardness as well as the flow strength was observed in the quaternary alloys. It was also shown that the wear resistance of the quaternary Ta(Ti) alloys was improved and attributed to plastically induced hardening of the worn surfaces combined with the positive temperature dependence of the flow strength. The strengthening and hardening resulting from Ta addition was suggested to be due to the hardening of the solid solution arising from the misfits in the atomic radius between Ta and the constituent atoms Ni, Ti or Si.

Superconductor with improved persistence characteristics

International Nuclear Information System (INIS)

Stekly, Z. J. J.; Strauss, B. P.

1984-01-01

In a multifilamentary superconductor, plural filaments are separated from one another by a ductile nonsuperconducting copper matrix. The niobium titanium filaments are arrayed through the copper, with one filament being substantially larger than the others, and preferably, centrally located in the wire. Preferably also, the other filaments are arrayed in an annular configuration about the periphery of the wire

Confining jackets for concrete cylinders using NiTiNb and NiTi shape memory alloy wires

Energy Technology Data Exchange (ETDEWEB)

Choi, Eunsoo; Yoon, Soon-Jong [Department of Civil Engineering, Hongik University, Seoul 121-791 (Korea, Republic of); Nam, Tae-Hyun [School of Materials Science and Engineering and ERI, Gyeongsang National University, Jinju, Gyeongnam 600-701 (Korea, Republic of); Cho, Sun-Kyu [School of Civil Engineering, Seoul National University of Technology, Seoul 139-743 (Korea, Republic of); Park, Joonam, E-mail: eunsoochoi@hongik.ac.k [Department of Railroad Structure Research, Korea Railroad Research Institute, Uiwang 437-050, Korea (Korea, Republic of)

2010-05-01

This study used prestrained NiTiNb and NiTi shape memory alloy (SMA) wires to confine concrete cylinders. The recovery stress of the wires was measured with respect to the maximal prestrain of the wires. SMA wires were preelongated during the manufacturing process and then wrapped around concrete cylinders of 150 mmx300 mm ({phi}xL). Unconfined concrete cylinders were tested for compressive strength and the results were compared to those of cylinders confined by SMA wires. NiTiNb SMA wires increased the compressive strength and ductility of the cylinders due to the confining effect. NiTiNb wires were found to be more effective in increasing the peak strength of the cylinders and dissipating energy than NiTi wires. This study showed the potential of the proposed method to retrofit reinforced concrete columns using SMA wires to protect them from earthquakes.

The novel superacid systems HSO3F-Nb(SO3F)5 and HSO3F-Ta(SO3F)5

International Nuclear Information System (INIS)

Cicha, W.V.; Aubke, F.

1989-01-01

The in situ oxidation of niobium and tantalum in HSO 3 F by bis(fluorosulfuryl) peroxide, S 2 O 6 F 2 , results in the formation of solvated Lewis acids M(SO 3 F) 5 , M = Nb or Ta. Both solutes behave as moderately strong, monoprotonic acids, based on electrical conductivity measurements over the concentration range 0-0.05 m and on conductometric titrations against KSO 3 F. These measurements suggest a general order of acidity, Au(SO 3 F) 3 > Ta(SO 3 F) 5 ≥ SbF 5 > Nb(SO 3 F) 5 > NbF 5 , all giving rise to monoprotonic acids. Supporting evidence comes from 1 H, 19 F, and 93 Nb NMR spectroscopy and the successful isolation and characterization of complexes of the type Cs n [M(SO 3 F) 5+n ], with M = Nb or Ta and n = 1 or 2, from these solutions

High temperature oxidation resistance of (Ti,Ta)(C,N)-based cermets

International Nuclear Information System (INIS)

Chicardi, E.; Córdoba, J.M.; Gotor, F.J.

2016-01-01

Highlights: • Cermets based on (Ti,Ta)(C,N) were oxidized in air between 800 and 1100 °C for 48 h. • The substitution of Ti by Ta resulted in a high resistance to oxidation. • A protective layer of cobalt titanates at the surface of cermets was observed. • A rutile phase in which some Ti"4"+ are replaced by Ta"5"+ was detected. • This replacement decelerated the oxygen diffusion into the cermets. - Abstract: Cermets based on titanium–tantalum carbonitride were oxidized in static air between 800 °C and 1100 °C for 48 h. The thermogravimetric and microstructural study showed an outstanding reduction in the oxidation of more than 90% when the Ta content was increased. In cermets with low Ta content, the formation of a thin CoO/Co_3O_4 outer layer tends to disappear by reacting with the underlying rutile phase, which emerges at the surface. However, in cermets with higher Ta content, the formation of an external titanate layer, observed even at a low temperature, appears to prevent the oxygen diffusion and the oxidation progression.

Magnetic hyperfine fields on 181Ta at the Nb and V sites in Heusler alloys CO2YAL (Y=NB,V)

International Nuclear Information System (INIS)

Pendl Junior, W.

1990-01-01

Magnetic hyperfine fields (MHF) acting on sup(181)Ta at the Nb and V sites have been determined in the Heusler alloys Co sub(2) NbA1 and Co sub(2) VA1 by the time differential perturbed angular correlation (TDPAC) technique utilizing the well known 133-482 Kev gamma cascade in sup(181)Ta. The measurement were carried out using an automatic spectrometer consisting of three NaI(T1) detectors and a fast-slow coincidence system. The measurements were performed at 77 K with and without an externally applied magnetic field ( ∼ 4.5 KGauss) to determine the sign as well as the magnitude of the hyperfine fields in both alloys. For the alloy Co sub(2) NbA1 a unique field of -138(4) KOe was observed whereas in the case of Co sub(2)VA1 two distinct magnetic sites were observed. The present result show that approximately 24% of the sup(181)Ta atoms in this alloy probe a field of -116(4) KOe while the other ∼ 76% of the atoms feel -83(3) KOe. Present data along with the existing results on similar alloys Co sub(2)T1,Hf,Zr (Al,Ga,Sn) are discussed and compared with the magnetic hyperfine field systematics in Heusler alloys. (author)

Effect of temperature on the mechanical properties of the high-field superconductor NbTi 50

International Nuclear Information System (INIS)

Albert, H.; Pfeiffer, I.

1976-01-01

Below 20 K the plastic deformation of NbTi 50 is exclusively determined by shear processes on [100] slip planes which become evident in stress decrements of the stress-strain curves. Increasing cold work facilitates the initiation of shear processes below 20 K inducing a decrease of the yield stress values. This phenomena is assumed to be due to the strengthening of the deformation texture with increasing cold work. Large α-Ti-precipitates (0.1 - 0.2 μm) produced by a 380 0 C heat treatment may act as notches initiating shear processes. They may also cause portions of brittle fracture in the microstructure of the otherwise ductile fracture at 4.2 K and 28 K. The yield stress is diminished. Finer and more homogeneously distributed precipitates resulting from additional deformation after heat treatment block up slip processes and therefore cause increased values of tensile strength and yield stress. In this case the material is not only electrically but also mechanically optimized. (orig.) [de

Low elastic modulus Ti-Ta alloys for load-bearing permanent implants: enhancing the biodegradation resistance by electrochemical surface engineering.

Science.gov (United States)

Kesteven, Jazmin; Kannan, M Bobby; Walter, Rhys; Khakbaz, Hadis; Choe, Han-Choel

2015-01-01

In this study, the in vitro degradation behaviour of titanium-tantalum (Ti-Ta) alloys (10-30 wt.% Ta) was investigated and compared with conventional implant materials, i.e., commercially pure titanium (Cp-Ti) and titanium-aluminium-vanadium (Ti6Al4V) alloy. Among the three Ti-Ta alloys studied, the Ti20Ta (6.3×10(-4) mm/y) exhibited the lowest degradation rate, followed by Ti30Ta (1.2×10(-3) mm/y) and Ti10Ta (1.4×10(-3) mm/y). All the Ti-Ta alloys exhibited lower degradation rate than that of Cp-Ti (1.8×10(-3) mm/y), which suggests that Ta addition to Ti is beneficial. As compared to Ti6Al4V alloy (8.1×10(-4) mm/y), the degradation rate of Ti20Ta alloy was lower by ~22%. However, the Ti30Ta alloy, which has closer elastic modulus to that of natural bone, showed ~48% higher degradation rate than that of Ti6Al4V alloy. Hence, to improve the degradation performance of Ti30Ta alloy, an intermediate thin porous layer was formed electrochemically on the alloy followed by calcium phosphate (CaP) electrodeposition. The coated Ti30Ta alloy (3.8×10(-3) mm/y) showed ~53% lower degradation rate than that of Ti6Al4V alloy. Thus, the study suggests that CaP coated Ti30Ta alloy can be a viable material for load-bearing permanent implants. Copyright © 2014 Elsevier B.V. All rights reserved.

Kinetics of high-temperature oxidation of (Ti,Ta)(C,N)-based cermets

International Nuclear Information System (INIS)

Chicardi, E.; Córdoba, J.M.; Gotor, F.J.

2016-01-01

Highlights: • The kinetic of high-temperature oxidation of (Ti,Ta)(C,N)-Co cermets was studied. • A parabolic oxidation kinetic was determined in cermets between 700 °C and 1200 °C. • This parabolic kinetic behaviour is due to the existence of a protective layer. • The protective layer formed was a complex Ti_xTa_1_−_xO_2 oxide with rutile structure. • The oxidation rate is controlled by the Ti and O_2 diffusion through the Ti_xTa_1_−_xO_2. - Abstract: The kinetics of the high-temperature oxidation of titanium–tantalum carbonitride-based cermets with different Ti/Ta ratios was studied. Isothermal oxidation tests were conducted under static air for 48 h at temperatures between 700 °C and 1200 °C. The oxidation satisfied the parabolic kinetics, characteristic of the existence of a protective oxide layer. The apparent activation energy suggests the rate-controlling process during oxidation is the simultaneous inward and outward diffusion of oxygen and titanium, respectively, through the formed protective layer, consisting mainly of a rutile phase. A higher Ta(V) content in the rutile decreased the oxygen diffusivity due to the reduction of oxygen vacancy concentration.

Corrosion Characteristics of Ti-29Nb-xHf Ternary Alloy for Biomaterials

Energy Technology Data Exchange (ETDEWEB)

Pak, Sun Young; Choi, Han Chul [Chosun Univ., Kwangju (Korea, Republic of)

2015-12-15

The Cp-Ti and Ti-6Al-4V alloys were widely used for dental materials due to their mechanical properties and good corrosion resistance. However, Cp-Ti was known as bio-inert materials, Ti-6Al-4V alloy has a problem such as high Young modulus, potential loss of the surrounding bone, and to the release of potentially toxic ions from the alloy. To overcome this problem, Ti alloys containing Nb and Hf elements have been used for biomaterials due to low toxicity and high corrosion resistance. Especially, alloying element of Nb was known as β phase stabilizer. The β phase alloy was widely used to replace currently used implant materials. The corrosion resistances of Ti-29Nb-xHf ternary alloys were dependent on Hf content in oral environment solution.

Na5NbO5 and Na5TaO5 phases

International Nuclear Information System (INIS)

Darriet, J.; Maazaz, A.; Bouloux, J.C.; Delmas, C.

1982-01-01

New ternary oxides of formulas Na 5 NbO 5 and Na 5 TaO 5 have been prepared. They crystallize in the monoclinic system (space group C2/c). The crystal structure of Na 5 NbO 5 has been determined. It derives from a NaCl-type structure by ordering of the cations and of the oxygen vacancies in the anionic sublattice, the corresponding formula being Nasub(5/6)Nbsub(1/6)Osub(5/6)vacant sub(1/6). Sodium and niobium have a distorted square-pyramidal surrounding. (author)

From Porous to Dense Nanostructured β-Ti alloys through High-Pressure Torsion.

Science.gov (United States)

Afonso, Conrado R M; Amigó, Angelica; Stolyarov, Vladimir; Gunderov, Dmitri; Amigó, Vicente

2017-10-19

β-Ti alloys have low elastic modulus, good specific strength and high corrosion resistance for biomaterial applications. Noble elements, such as Nb, Ta and Mo, are used to obtain β-Ti due to their chemical biocompatibility. However, due to their refractory nature, β-Ti requires specific processing routes. Powder metallurgy (P/M) allows for the development of new β-Ti alloys with decreasing costs, but dealing with high-elemental-content alloys can lead to a lack of diffusion and grain growth. One method to refine the structure and improve mechanical properties is a severe plastic deformation technique through high-pressure torsion (HPT). The aim of this work was to evaluate the conversion of P/M porous β-Ti-35Nb-10Ta-xFe alloys to dense nanostructures through high-pressure torsion in one deformation step and the influence of the structure variation on the properties and microstructure. TEM analysis and ASTAR crystallographic mapping was utilized to characterize the nanostructures, and the properties of P/M β Ti-35Nb-10Ta-xFe alloys processed by HPT were compared. The initial microstructure consisted mainly by the β-Ti phase with some α-Ti phase at the grain boundaries. The HPT process refined the microstructure from 50 µm (P/M) down to nanostructured grains of approximately 50 nm.

Growth mechanism, distribution characteristics and reinforcing behavior of (Ti, Nb)C particle in laser cladded Fe-based composite coating

International Nuclear Information System (INIS)

Li, Qingtang; Lei, Yongping; Fu, Hanguang

2014-01-01

Highlights: • Reinforced (Ti, Nb)Cp can be synthesized in the molten pool during laser cladding. • Formation mechanism of (Ti, Nb)Cp are impacted by Ti/Nb atomic ratio. • Appropriate Ti element can improve the precipitation of carbide particle. • Excess Ti weakens this effect above-mentioned. • The wear resistance of the coating was improved when Ti/Nb = 1. - Abstract: Over the past decade, researchers have demonstrated much interest in laser cladded metal matrix composite coatings for its good wear resistance, corrosion resistance, and high temperature properties. In this paper, in-situ (Ti, Nb)C particle reinforced Fe-based composite coatings were produced by laser cladding. The effects of Ti/Nb(atomic ratio) in the cladding powder on the formation mechanism and distribution characteristics of multiple particle were investigated. The results showed that when Ti/Nb > 1, Ti had a stronger ability to bond with C compared with Nb. (Ti, Nb)C multiple particles with TiC core formed in the molten pool. With the decrease of Ti/Nb, core-shell structure disappeared, the structure of particle got close to that of NbC gradually. It is found that the amount, area ratio and distribution of the reinforced particle in the coating containing Ti and Nb elements were improved, compared with these in the coating containing equal Nb element. When Ti/Nb = 1, the effects above-mentioned is most prominent, and the wear resistance of the coating is promoted obviously

Growth mechanism, distribution characteristics and reinforcing behavior of (Ti, Nb)C particle in laser cladded Fe-based composite coating

Energy Technology Data Exchange (ETDEWEB)

Li, Qingtang, E-mail: liqingtang123@126.com; Lei, Yongping, E-mail: yplei@bjut.edu.cn; Fu, Hanguang

2014-10-15

Highlights: • Reinforced (Ti, Nb)Cp can be synthesized in the molten pool during laser cladding. • Formation mechanism of (Ti, Nb)Cp are impacted by Ti/Nb atomic ratio. • Appropriate Ti element can improve the precipitation of carbide particle. • Excess Ti weakens this effect above-mentioned. • The wear resistance of the coating was improved when Ti/Nb = 1. - Abstract: Over the past decade, researchers have demonstrated much interest in laser cladded metal matrix composite coatings for its good wear resistance, corrosion resistance, and high temperature properties. In this paper, in-situ (Ti, Nb)C particle reinforced Fe-based composite coatings were produced by laser cladding. The effects of Ti/Nb(atomic ratio) in the cladding powder on the formation mechanism and distribution characteristics of multiple particle were investigated. The results showed that when Ti/Nb > 1, Ti had a stronger ability to bond with C compared with Nb. (Ti, Nb)C multiple particles with TiC core formed in the molten pool. With the decrease of Ti/Nb, core-shell structure disappeared, the structure of particle got close to that of NbC gradually. It is found that the amount, area ratio and distribution of the reinforced particle in the coating containing Ti and Nb elements were improved, compared with these in the coating containing equal Nb element. When Ti/Nb = 1, the effects above-mentioned is most prominent, and the wear resistance of the coating is promoted obviously.

Diffusion of titanium and niobium in b.c.c. Ti--Nb alloys

International Nuclear Information System (INIS)

Pontau, A.E.

1978-01-01

The diffusion coefficients for titanium and niobium radioactive tracers were simultaneously measured in Ti, Ti 94 6 Nb 5 4 , Ti 80 4 Nb 19 6 , and Ti 64 3 Nb 35 . 7 over the temperature range from 950 0 C to 1511 0 C using standard lathe sectioning techniques. The samples were initially heat treated by annealing above the α-β phase transition temperature and then either cooling slowly to room temperature or quenching. The room temperature crystal morphology was then examined using x-ray diffraction. Alloy concentrations were chosen both to suppress the β-α transition and to obtain the metastable ω-phase

Structural properties, deformation behavior and thermal stability of martensitic Ti-Nb alloys

Energy Technology Data Exchange (ETDEWEB)

Boenisch, Matthias

2016-06-10

Ti-Nb alloys are characterized by a diverse metallurgy which allows obtaining a wide palette of microstructural configurations and physical properties via careful selection of chemical composition, heat treatment and mechanical processing routes. The present work aims to expand the current state of knowledge about martensite forming Ti-Nb alloys by studying 15 binary Ti-c{sub Nb}Nb (9 wt.% ≤ c{sub Nb} ≤ 44.5 wt.%) alloy formulations in terms of their structural and mechanical properties, as well as their thermal stability. The crystal structures of the martensitic phases, α{sup '} and α'', and the influence of the Nb content on the lattice (Bain) strain and on the volume change related to the β → α{sup '}/α'' martensitic transformations are analyzed on the basis of Rietveld-refinements. The magnitude of the shuffle component of the β → α{sup '}/α'' martensitic transformations is quantified in relation to the chemical composition. The largest transformation lattice strains are operative in Nb-lean alloys. Depending on the composition, both a volume dilatation and contraction are encountered and the volume change may influence whether hexagonal martensite α{sup '} or orthorhombic martensite α'' forms from β upon quenching. The mechanical properties and the deformation behavior of martensitic Ti-Nb alloys are studied by complementary methods including monotonic and cyclic uniaxial compression, nanoindentation, microhardness and impulse excitation technique. The results show that the Nb content strongly influences the mechanical properties of martensitic Ti-Nb alloys. The elastic moduli, hardness and strength are minimal in the vicinity of the limiting compositions bounding the interval in which orthorhombic martensite α'' forms by quenching. Uniaxial cyclic compressive testing demonstrates that the elastic properties of strained samples are different than those of unstrained ones

Effect of Nb on plasticity and oxidation behavior of TiA1Nb intermetallic compound by density functional theory

Institute of Scientific and Technical Information of China (English)

LI Yan-feng; XU Hui; SONG Zhao-quan; MA Song-shan

2010-01-01

Based on the pseudo potential plane-wave method of density functional theory(DFT),Ti1-xNbxA1(x=0,0.062 5,0.083 3,0.125,0.250)crystals' geometry structure,elastic constants,electronic structure and Mulliken populations were calculated,and the effects of doping on the geometric structure,electronic structure and bond strength were systematically analyzed.The results show that the influence of Nb on the geometric structure is little in terms of the plasticity,and with the increase of Nb content,the covalent bond strength remarkably reduces,and Ti-A1,Nb-M(M=Ti,A1)and other hybrid bonds enhance; meanwhile,the peak district increases and the pseudo-energy gap first decreases and then increases,the overall band structure narrows,the covalent bond and direction of bonds reduce.The population analysis also shows that the results are consistent with the electronic structure analysis.The density of states of TiAlNb shows that Nb doping can enhance the activity of Al and benefit the form of Al2O3 film.All the calculations reveal that the room temperature plasticity and the antioxidation properties of the compounds can be improved with the Nb content of 8.33%-12.5%(mole fraction).

Are lithium niobate (LiNbO{sub 3}) and lithium tantalate (LiTaO{sub 3}) ferroelectrics bioactive?

Energy Technology Data Exchange (ETDEWEB)

Vilarinho, Paula Maria, E-mail: paula.vilarinho@ua.pt; Barroca, Nathalie; Zlotnik, Sebastian; Félix, Pedro; Fernandes, Maria Helena

2014-06-01

The use of functional materials, such as ferroelectrics, as platforms for tissue growth in situ or ex situ, is new and holds great promise. But the usage of materials in any bioapplication requires information on biocompatibility and desirably on bioactive behavior when bone tissue engineering is envisaged. Both requirements are currently unknown for many ferroelectrics. Herein the bioactivity of LiNbO{sub 3} and LiTaO{sub 3} is reported. The formation of apatite-like structures on the surface of LiNbO{sub 3} and LiTaO{sub 3} powders after immersion in simulated body fluid (SBF) for different soaking periods indicates their bioactive potential. The mechanism of apatite formation is suggested. In addition, the significant release of lithium ions from the ferroelectric powders in the very first minutes of soaking in SBF is examined and ways to overcome this likely hurdle addressed. - Highlights: • LiNbO{sub 3} and LiTaO{sub 3} are bioactive ferroelectrics. • Cauliflower apatite type structures indicative of in-vitro bioactivity of LiNbO{sub 3} and LiTaO{sub 3.} • Negative surface charges anchor Ca{sup 2+} to which PO{sub 4}{sup 3−} attracts forming apatite structure nuclei. • Use of ferroelectrics as platforms for tissue growth in situ or ex situ is new and holds great promise.

Microstructures and phase transformations of Ti-30Zr-xNb (x = 5, 7, 9, 13 at.%) shape memory alloys

Energy Technology Data Exchange (ETDEWEB)

Qu, Wentao; Sun, Xuguang; Yuan, Bifei [School of Mechanical Engineering, Xi' an Shiyou University, Xi' an 710065 (China); Xiong, Chengyang; Zhang, Fei [School of Materials Science and Engineering, Beihang University, Beijing 100191 (China); Li, Yan, E-mail: liyan@buaa.edu.cn [School of Materials Science and Engineering, Beihang University, Beijing 100191 (China); Sun, Baohui [Lanzhou Seemine SMA Co. Ltd., Lanzhou 730010 (China)

2016-12-15

The microstructures, phase transformations and shape memory properties of Ti-30Zr-xNb (x = 5, 7, 9, 13 at.%) alloys were investigated. The X-ray diffraction and transmission electron microscopy observations showed that the Ti-30Zr-5Nb, Ti-30Zr-7/9Nb and Ti-30Zr-13Nb alloys were composed of the hcp α′-martensite, orthorhombic α″-martensite and β phases, respectively. The results indicated the enhanced β-stabilizing effect of Nb in Ti-30Zr-xNb alloys than that in Ti-Nb alloys due to the high content of Zr. The differential scanning calorimetry test indicated that the Ti-30Zr-5Nb alloy displayed a reversible transformation with a high martensitic transformation start temperature of 776 K and a reverse martensitic transformation start temperature (A{sub s}) of 790 K. For the Ti-30Zr-7Nb and Ti-30Zr-9Nb alloys, the martensitic transformation temperatures decreased with the increasing Nb content. Moreover, an ω phase transformation occurred in the both alloys upon heating at a temperature lower than the corresponding A{sub s}, which is prompted by more addition of Nb. Although the critical stress in tension of the three martensitic alloys decreased with increasing Nb content, the Ti-30Zr-9Nb alloy showed a critical stress of as high as 300 MPa. Among all the alloys, the Ti-30Zr-9Nb alloy exhibited the maximum shape memory effect of 1.61%, due to the lowest critical stress for the martensite reorientation. - Highlights: •Ti-30Zr-5Nb alloy is composed of hcp α′-martensite with the M{sub s} of 776 K. •Ti-30Zr-7Nb and Ti-30Zr-9Nb alloys are predominated by orthorhombic α″-martensite. •Ti-30Zr-13Nb alloy consists of a single β phase due to the β-stabilizing effect of Nb. •The martensitic transformation temperatures decrease with increasing Nb content. •Ti-30Zr-9Nb alloy shows the maximum shape memory effect of 1.61%.

Superconductor-ferromagnet-superconductor nanojunctions from perovskite materials

Energy Technology Data Exchange (ETDEWEB)

Štrbík, V., E-mail: vladimir.strbik@savba.sk [Institute of Electrical Engineering, SAS, Dúbravská Cesta 9, Bratislava (Slovakia); Beňačka, Š.; Gaži, Š.; Španková, M.; Šmatko, V. [Institute of Electrical Engineering, SAS, Dúbravská Cesta 9, Bratislava (Slovakia); Knoška, J. [Center for Free-Electron Laser Science, DESY, Notkestraße 85, 22607, Hamburg (Germany); Department of Physics, University of Hamburg, Luruper Chaussee 149, 22607, Hamburg (Germany); Gál, N.; Chromik, Š.; Sojková, M.; Pisarčík, M. [Institute of Electrical Engineering, SAS, Dúbravská Cesta 9, Bratislava (Slovakia)

2017-02-15

Highlights: • Superconductor-ferromagnet-superconductor nanojunction. • Nanojunctions prepared by Ga{sup 3+} focused ion beam patterning. • Indication of triplet Cooper pair component in junction superconducting current. • Qualitative agreement with theoretical model. - Abstract: The lateral superconductor-ferromagnet–superconductor (SFS) nanojunctions based on high critical temperature superconductor YBa{sub 2}Cu{sub 3}O{sub x} (YBCO) and half-metallic ferromagnet La{sub 0.67}Sr{sub 0.33}MnO{sub 3} (LSMO) thin films were prepared to investigate a possible presence of long range triplet component (LRTC) of Cooper pairs in the LSMO. We applied Ga{sup 3+} focused ion beam patterning to create YBCO/LSMO/YBCO lateral type nanojunctions with LSMO length as small as 40 nm. The resistivity vs. temperature, critical current density vs. temperature and resistance vs. magnetic field dependence were studied to recognize the LRTC of Cooper pairs in the LSMO. A non-monotonic temperature dependence of junction critical current density and a decrease of the SFS nanojunction resistance in increased magnetic field were observed. Only weak manifestations of LRTC and some qualitative agreement with theory were found out in SFS nanojunctions realized from the perovskite materials. The presence of equal-spin triplet component of Cooper pairs in half-metallic LSMO ferromagnet is not such apparent as in SFS junctions prepared from low temperature superconductors NbTiN and half-metallic ferromagnet CrO{sub 2}.

Synthesis and characterization of Ag-doped TiO2 nanotubes on Ti-6Al-4V and Ti-6Al-7Nb alloy

Science.gov (United States)

Ulfah, Ika Maria; Bachtiar, Boy M.; Murnandityas, Arnita Rut; Slamet

2018-05-01

The present paper is focused on comparative behavior of nanotubes growth on Ti-6Al-4V and Ti-6Al-7Nb alloy using electrochemical anodization method. These alloys were anodized in electrolytes solution containing glycerol, water and 0.5wt.% of NH4F. Silver-doped TiO2 nanotubes were synthesized using photo-assisted deposition (PAD) at various Ag loading concentration in 0.05 M, 0.10 M, and 0.15 M. The phase composition and morphological characteristics were investigated by XRD and FESEM/EDX, respectively. The surface wettability was measured by contact angle meter. The results showed that TiO2 nanotubes can be grown on these surface alloys. XRD profiles revealed crystal formation of anatase, rutile and Ag on these surface alloys. According to FESEM images, the average nanotube diameter of Ti-6Al-4V alloy and Ti-6Al-7Nb alloy are 134 nm and 120 nm, respectively. EDX-Mapping analysis showed that Ag desposited over surface of TiO2 nanotubes. The surface wettability indicated hydrophilicity properties on Ti-4Al-4V alloy and Ti-6Al-7Nb alloy surface. This study may contribute to the development of silver-doped TiO2 nanotubes on Ti-6Al-4V alloy and Ti-6Al-7Nb alloy can be considered in various photocatalytic applications such as biomedical devicesdue to photocatalytic mechanism and antibacterial ability.

Structure and mechanical properties of a two-layered material produced by the E-beam surfacing of Ta and Nb on the titanium base after multiple rolling

Science.gov (United States)

Bataev, V. A.; Golkovski, M. G.; Samoylenko, V. V.; Ruktuev, A. A.; Polyakov, I. A.; Kuksanov, N. K.

2018-04-01

The study has been conducted in line with the current approach to investigation of materials obtained by considerably deep surface alloying of the titanium substrate with Ta, Nb, and Zr. The thickness of the resulting alloyed layer was equal to 2 mm. The coating was formed through weld deposition of a powder with the use of a high-voltage electron beam in the air. It has been lately demonstrated that manufactured such a way alloyed layers possess corrosion resistance which is significantly higher than the resistance of titanium substrates. It has already been shown that such two-layered materials are weldable. The study objective is to investigate the feasibility of rolling for necking the sheets with the Ti-Ta-Nb anticorrosion coating with further fourfold decrease in their thickness. The research is also aimed at investigation of the material properties after rolling. Anticorrosion layers were formed both on CP-titanium and on VT14 (Ti-4Al-3Mo-1 V) durable titanium alloy. The results of chemical composition determination, structure examination, X-ray phase analysis and mechanical properties observations (including bending properties of the alloyed layers) are presented in the paper. The combination of welding, rolling, and bending enables the manufacture of corrosion-resistant vessels and process pipes which are made from the developed material and find technological application.

Tuning electronic structure and optical properties of SrTiO{sub 3} by site-specific doping by Nb with N/B from hybrid functional calculations

Energy Technology Data Exchange (ETDEWEB)

Liu, Yanyu; Zhou, Wei; Wu, Ping, E-mail: pingwu@tju.edu.cn

2017-07-01

In this study, the extensive density functional theory calculations are performed to modify the electronic structure of perovskite SrTiO{sub 3} by doping with Nb and N/B. The unoccupied states induced by the Nb monodoping at the Sr or Ti site, which were passivated in the codoped systems (the substitution of Nb at Ti site with the replacement of N at O site: Nb@Ti/N@O and the substitution of Nb at Sr site with the replacement of B at O site: Nb@Sr/B@O). The charge-compensated donor-acceptor pair codoping creates the new occupied states within the band gap, which yields the absorption edge extend to visible light. And the calculated defect formation energy implies that the codoped systems are energetically favorable under the O-rich condition. Moreover, the band-edge alignment confirmed that the Nb@Ti/N@O system is desirable for the spontaneous water splitting under visible light and the Nb@Sr/B@O system can split water into hydrogen in presence of sacrificial agent. - Highlights: • A systematical study has been employed on SrTiO{sub 3} with the donor-acceptor codoping. • The donor-acceptor pair codoping yields the absorption edge extend to visible light. • The formation energy implies that the codoped systems are favorable under the O-rich condition. • The Nb@Ti/N@O system is desirable for the spontaneous water splitting under visible light. • The Nb@Sr/B@O system can split water into hydrogen in presence of sacrificial agent.

Textured and tungsten-bronze-niobate-doped (K,Na,Li)(Nb,Ta)O3 piezoceramic materials

International Nuclear Information System (INIS)

Soller, Thomas; Bathelt, Robert; Benkert, Katrin; Bodinger, Hermann; Schuh, Carsten; Schlenkrich, Falko

2010-01-01

In this study, the effects of an alkaline-earth niobate doping in tungsten-bronze (TB) stoichiometry on the piezoelectric properties and the phase transition temperatures of lead-free (K,Na,Li)(Nb,Ta)O 3 ceramics were investigated. In particular, the TB compounds barium niobate (BN), barium sodium niobate (BNN) and strontium calcium sodium niobate (SCNN) were investigated. The TB-modified ceramics show promising piezoelectric properties with large-signal piezo coefficients, d 33 * lose to 400 pm/V, planar coupling coefficients, k p , up to 0.45 and Curie temperatures of approximately 310 .deg. C. In addition, the effect of texturing on the undoped (K,Na,Li)(Nb,Ta)O 3 base composition via templated grain growth (TGG) with microcrystalline NaNbO 3 templates was examined. Lotgering factors up to 81% and strain enhancements by a factor 1.5 with large-signal values of d 33 * up to 550 pm/V could be achieved in the textured samples.

Crystallographic Structure Analysis of a Ti-Ta Thin Film Materials Library Fabricated by Combinatorial Magnetron Sputtering.

Science.gov (United States)

Kadletz, Peter M; Motemani, Yahya; Iannotta, Joy; Salomon, Steffen; Khare, Chinmay; Grossmann, Lukas; Maier, Hans Jürgen; Ludwig, Alfred; Schmahl, Wolfgang W

2018-03-12

Ti-Ta thin films exhibit properties that are of interest for applications as microactuators and as biomedical implants. A Ti-Ta thin film materials library was deposited at T = 25 °C by magnetron sputtering employing the combinatorial approach, which led to a compositional range of Ti 87 Ta 13 to Ti 14 Ta 86 . Subsequent high-throughput characterization methods permitted a quick and comprehensive study of the crystallographic, microstructural, and morphological properties, which strongly depend on the chemical composition. SEM investigation revealed a columnar morphology having pyramidal, sharp tips with coarser columns in the Ti-rich and finer columns in the Ta-rich region. By grazing incidence X-ray diffraction four phases were identified, from Ta-lean to Ta-rich: ω phase, α″ martensite, β phase, and a tetragonal Ta-rich phase (Ta (tetr) ). The crystal structure and microstructure were analyzed by Rietveld refinement and clear trends could be determined as a function of Ta-content. The lattice correspondences between β as the parent phase and α″ and ω as derivative phases were expressed in matrix form. The β ⇌ α″ phase transition shows a discontinuity at the composition where the martensitic transformation temperatures fall below room temperature (between 34 and 38 at. % Ta) rendering it first order and confirming its martensitic nature. A short study of the α″ martensite employing the Landau theory is included for a mathematical quantification of the spontaneous lattice strain at room temperature (ϵ̂ max = 22.4(6) % for pure Ti). Martensitic properties of Ti-Ta are beneficial for the development of high-temperature actuators with actuation response at transformation temperatures higher than 100 °C.

Superconductors with low critical temperature for electro-magnets; Supraconducteurs a basse temperature critique pour electroaimants

Energy Technology Data Exchange (ETDEWEB)

Devred, A

2002-07-01

Among the superconductors with low critical temperature that are used to build magnets, NbTi has reached a development state that allows a massive production for big equipment of physics and an industrial production in the domain of medicine imaging. The material that might challenge the supremacy of NbTi is Nb{sub 3}Sn but some technical difficulties have yet to be overcome. This report begins with a review of the different industrial processes used to produce superconducting wires based on the NbTi and Nb{sub 3}Sn materials. The transition from the superconducting state to the resistive normal state is described for both materials, the magnetizing of multi-wire superconducting cables is also presented. The author details the different patterns of wires in cables and proposes a formulary that allows the determination, in some simple cases,of energy losses that are generated in a superconducting cable by a variable magnetic field. (A.C.)

Effect of β-phase decomposition on the superconducting properties of Ti-27 at percent Nb solid solution

International Nuclear Information System (INIS)

Hariharan, Y.; Valsakumar, M.C.; Radhakrishnan, T.S.

1980-01-01

The effect of β-phase decomposition on the superconducting transition temperature (Tsub(c)) of a Ti-27 at % Nb solid solution has been studied by the resistive technique. The samples were β-quenched from 900deg C and cold rolled to 30%. Annealing at 400deg C for various times upto 15 hours causes Ti-rich phases to precipitate out of the matrix. This decomposition of the β-phase is seen to lead to a progressive enhancement in Tsub(c) from 7.7 K in the β-quenched state to 8.8 K in the sample annealed for 15 hours; further, the width Δ Tsub(c) of the superconducting transition (=90 mK in the β-quenched state) reaches a maximum value (360 mK) for a 10-hour anneal. The conjecture that the enhancement in Tsub(c) occurs as a result of precipitation and the consequent enrichment of the Nb content of the matrix is examined. It is estimated that to account for the large observed enhancement of Tsub(c), the Nb enrichment would have to be of the order of 5-6%; whereas a TEM study has revealed the enrichment to be of the order of 0.2% only. Analysis of the X-ray diffractograms is also not in favour of this hypothesis. Hence alternative mechanisms to account for the Tsub(c) enhancement are currently under investigation. Also discussed is the calculation of Tsub(c) using McMillan's formula for strongly coupled superconductors. (author)

Stress effects on multifilamentary Nb3Sn wire

International Nuclear Information System (INIS)

Bartlett, R.J.; Taylor, R.D.; Thompson, J.D.

1979-01-01

Critical current I/sub c/ measurements were obtained on highly stabilized mf Nb 3 Sn wires as a function of heat treatment, stress, temperature, and applied magnetic field. The ratio of the area of the copper to bronze core-niobium tube is about 8, and the filaments are concentrated in the inner 30% of the wire cross section. Values of I/sub c/ and T/sub c/ were determined for samples subjected to a wide range of heat treatments. Diffusion reaction times and temperatures in the ranges 16 to 128 hr and 700 to 750 0 C provided a number of mf Nb 3 Sn wires having similar I/sub c/ characteristics. To some extent the residual compressive loading on the Nb 3 Sn wires varied with the particular heat treatment. This loading arises primarily from the differential contraction of the remaining bronze and the Nb 3 Sn layer when cooled from the reaction temperature to the operating temperature. It was found that, by controlled bending or stretching of the wires, whereby some of the strain in the Nb 3 Sn is relieved, the I/sub c/ at 14 K is increased by as much as 30% and the critical temperature is increased by up to 1 K

An intermetallic powder-in-tube approach to increased flux-pinning in Nb3Sn by internal oxidation of Zr

Science.gov (United States)

Motowidlo, L. R.; Lee, P. J.; Tarantini, C.; Balachandran, S.; Ghosh, A. K.; Larbalestier, D. C.

2018-01-01

We report on the development of multifilamentary Nb3Sn superconductors by a versatile powder-in-tube technique (PIT) that demonstrates a simple pathway to a strand with a higher density of flux-pinning sites that has the potential to increase critical current density beyond present levels. The approach uses internal oxidation of Zr-alloyed Nb tubes to produce Zr oxide particles within the Nb3Sn layer that act as a dispersion of artificial pinning centres (APCs). In this design, SnO2 powder is mixed with Cu5Sn4 powder within the PIT core that supplies the Sn for the A15 reaction with Nb1Zr filament tubes. Initial results show an average grain size of ˜38 nm in the A15 layer, compared to the 90-130 nm of typical APC-free high-J c strands made by conventional PIT or Internal Sn processing. There is a shift in the peak of the pinning force curve from H/H irr of ˜0.2 to ˜0.3 and the pinning force curves can be deconvoluted into grain boundary and point-pinning components, the point-pinning contribution dominating for the APC Nb-1wt%Zr strands.

Structural evolution of Ba{sub 8}Ti{sub 3}Nb{sub 4}O{sub 24} from BaTiO{sub 3} using a series of Ba(Ti{sub 1−5x}Nb{sub 4x})O{sub 3} solid solutions

Energy Technology Data Exchange (ETDEWEB)

Barrientos Hernández, F.R., E-mail: frbh68@hotmail.com [Academic Area of Earth Sciences and Materials, Autonomous University of Hidalgo State, Road Pachuca-Tulancingo km 4.5, Mineral de la Reforma zip code 42184, Hidalgo (Mexico); Department of Metallurgical and Materials Engineering, ESIQIE, National Polytechnic Institute, UPALM, Zacatenco, Mexico City, zip code 07738 (Mexico); Lira Hernández, I.A. [Department of Metallurgical and Materials Engineering, ESIQIE, National Polytechnic Institute, UPALM, Zacatenco, Mexico City, zip code 07738 (Mexico); Industrial Engineering Department, Technological Institute of Pachuca, Road México-Pachuca km. 87.5, Pachuca de Soto zip code 42080, Hidalgo (Mexico); Gómez Yáñez, C. [Department of Metallurgical and Materials Engineering, ESIQIE, National Polytechnic Institute, UPALM, Zacatenco, Mexico City, zip code 07738 (Mexico); Arenas Flores, A. [Academic Area of Earth Sciences and Materials, Autonomous University of Hidalgo State, Road Pachuca-Tulancingo km 4.5, Mineral de la Reforma zip code 42184, Hidalgo (Mexico); Cabrera Sierra, R. [Department of Metallurgical and Materials Engineering, ESIQIE, National Polytechnic Institute, UPALM, Zacatenco, Mexico City, zip code 07738 (Mexico); Pérez Labra, M. [Academic Area of Earth Sciences and Materials, Autonomous University of Hidalgo State, Road Pachuca-Tulancingo km 4.5, Mineral de la Reforma zip code 42184, Hidalgo (Mexico)

2014-01-15

Highlights: • The evolution phase Ba{sub 8}Ti{sub 3}Nb{sub 4}O{sub 24} was obtained through the mechanism Ba(Ti{sub 1-5x}Nb{sub 4x})O{sub 3}. • Addition of niobium can accelerate grain growth of BaTiO{sub 3} ceramics. • Ba{sub 8}Ti{sub 3}Nb{sub 4}O{sub 24} presents a dielectric loss of 0.0035 and permittivity value of 54.6. • Electrical measurements showed that Nb{sup 5+} content drops Curie temperature. • Samples with x ⩾ 0.0625 shows an insulating behavior. -- Abstract: In this work, the structural evolution of hexagonal phase Ba{sub 8}Ti{sub 3}Nb{sub 4}O{sub 24} by adding Nb{sub 2}O{sub 5} to perovskite structure of BaTiO{sub 3} was investigated. The compositions Ba(Ti{sub 1-5x}Nb{sub 4x})O{sub 3} ceramics, with 0.00025 ⩽ x ⩽ 0.125 were prepared by the conventional solid state route in air atmosphere, the powders precursors, BaTiO{sub 3}, BaCO{sub 3} and Nb{sub 2}O{sub 5}, were mixed in stoichiometric proportions and ground in a ball mill using alumina balls and acetone. The mixed powders were calcined at temperatures up to 1500 °C. The phase transformation of Ba{sub 8}Ti{sub 3}Nb{sub 4}O{sub 24} from BaTiO{sub 3} was studied by DRX, Raman spectroscopy, SEM, electrical measurements (relative permittivity and P–E hysteresis loops); Rietveld’s refinement was used to structurally characterize the samples. For the devices obtained capacitance was measured at 1 kHz; with these values we calculated the relative permittivity. The samples show typical P–E hysteresis loops at room temperature accompanied by saturation polarization (Ps) and remnant polarization (Pr). The DRX and Rietveld’s refinement results show x ⩽ 0.01 has a ferroelectric behavior. When the doped level is increased x ⩾ 0.02, a peak displacement is observed, this is due to the phase transformation of tetragonal to cubic into the unit cell. Finally, with x = 0.125 the crystal structure transforms to the characteristic hexagonal phase Ba{sub 8}Ti{sub 3}Nb{sub 4}O{sub 24} which

Microwave-Hydrothermal Synthesis and Characterization of High-Purity Nb Doped BaTiO3 Nanocrystals

Directory of Open Access Journals (Sweden)

A. Khanfekr

2014-01-01

Full Text Available The synthesis of Nb doped BaTiO3 has been investigated under Microwave-Hydrothermal (MH conditions in the temperature of 150°C for only 2 h using C16H36O4Ti, BaH2O2.8H2O and NbCl5 as Ba, Ti and  Nb sources, respectively.  Typical experiments performed on MH processing have not yet reported for Nb doped BaTiO3.  In the MH process, the formation of high purity nano tetragonal Nb-BaTiO3 was strongly enhanced. New hydrothermal method was used instead of the previous solid state reaction for the BaTiO3±Nb2O3 system. The new method uses high pressure to create nano dimension particles in a lower time and temperature. In case of the phase evolution studies, the XRD pattern measurements and Raman spectroscopy were performed. TEM and FE-SEM images were taken for the detailed analysis of the particle size, surface and morphology.  Synthesis of Nb doped BaTiO3 with the Microwave-hydrothermal provides an advantage of fast crystallization and reduced crystal size when compared to existing methods.

Optical and semiconductive properties of binary and ternary thin films from the Nb-Ti-O system

Science.gov (United States)

Aperador, W.; Yate, L.; Pinzón, M. J.; Caicedo, J. C.

2018-06-01

A study has been conducted based on the Mott-Schottky model acquisition by potentiodynamic electrochemical impedance spectroscopy, to determine the physical-chemical properties of binary TiO2, Nb2O5 and ternary Nb-Ti-O thin films (semiconductor type) based on Nb,Ti, O elements. The technique used for the study of optical properties was that of spectral transmittance, measurements were performed using a spectrophotometer. The consistency of the impedance data has been studied by calculating the Kramers-Kronig relations. The structural properties were analyzed by XRD patterns; the chemical composition measurements for all thin films were made by using XPS technique. So, in this research the transmittance values change from 72.74% for Nb2O5 to 59.68% for Ti-Nb-O with wavelength around 355 nm. The absorption coefficients for all films were analyzed from 31823.87 cm-1 for Nb2O5 to 91240.90 cm-1 for Nb-Ti-O with wavelength around 355 nm evidencing thus a 65% reduction. The direct band gap it was found that the photon energy (band gap Eg) changes in all films from 3.56 eV for Nb2O5 to 3.96 eV for Ti-Nb-O evidencing a 10% reduction. The extinction coefficient values change in all films from 0.038 cm-1 for Nb2O5 to 0.277 cm-1 for Ti-Nb-O films with wavelength around 355 nm, exhibiting an 86% increasing. Finally, it was observed by the Mott-Schottky analysis that the reference potential (Ag/AgCl) changes for all films from -2.09 V for Nb2O5 to -0.80 V for Ti-Nb-O material showing a 62% reduction.

Oxidation behaviors of the TiNi/Ti_2Ni matrix composite coatings with different contents of TaC addition fabricated on Ti6Al4V by laser cladding

International Nuclear Information System (INIS)

Lv, Y.H.; Li, J.; Tao, Y.F.; Hu, L.F.

2016-01-01

The TiNi/Ti_2Ni matrix composite coatings were fabricated on Ti6Al4V by laser cladding the mixtures of NiCrBSi and different contents of TaC (0 wt%, 5 wt%, 15 wt%, 30 wt% and 40 wt%). Scanning electron microscopy (SEM), energy dispersive spectrometry (EDS) and X-ray diffractometry (XRD) were used to examine the microstructures of the coatings. Oxidation behaviors of these coatings were also investigated at 800 °C for 50 h in air. The results showed that the coating without TaC addition was mainly composed of TiNi/Ti_2Ni as the matrix and TiC/TiB_2/TiB as the reinforcement. TaC was dissolved completely and precipitated again during laser cladding. Ta and C from the added TaC mainly existed as the solute atoms in the solid solutions of TiC, TiB_2 and TiB in the coatings with TaC addition. The addition of TaC refined the microstructures of the coatings. In the oxidation test, the oxidation process was divided into the violent oxidation stage and the slow oxidation stage. The oxidation rates of the substrate and the coatings with different contents of TaC (0, 5, 15, 30, 40 wt%) were 0.644, 0.287, 0.173, 0.161, 0.223 and 0.072 mg cm"−"2 h"−"1 in the first stage, 0.884, 0.215, 0.136, 0.126, 0.108 and 0.040 mg"2 cm"−"4 h"−"1 in the second stage, respectively. The weight gain of these samples were 6.70, 3.30, 2.86, 2.64, 2.41 and 1.69 mg cm"−"2, respectively after the whole oxidation test. The oxidation film formed on the surface of the coating without TaC addition mainly consisted of TiO_2, Al_2O_3, and a small amount of NiO, Cr_2O_3 and SiO_2. Moreover, Ta_2O_5 was also formed on the surfaces of these coatings with different contents of TaC. The oxides formed during the oxidation test were supposed to be responsible for the improvement in oxidation resistance of these coatings. - Highlights: • The composite coatings with TaC addition were fabricated on Ti6Al4V by laser cladding. • Effect of TaC addition on microstructural evolution of the coatings was

Mechanical properties and grindability of dental cast Ti-Nb alloys.

Science.gov (United States)

Kikuchi, Masafumi; Takahashi, Masatoshi; Okuno, Osamu

2003-09-01

Aiming at developing a dental titanium alloy with better mechanical properties and machinability than unalloyed titanium, a series of Ti-Nb alloys with Nb concentrations up to 30% was made. They were cast into magnesia-based molds using a dental casting machine and the mechanical properties and grindability of the castings were examined. The hardness of the alloys with Nb concentrations of 5% and above was significantly higher than that of titanium. The yield strength and tensile strength of the alloys with Nb concentrations of 10% and above were significantly higher than those of titanium, while the elongation was significantly lower. A small addition of niobium to titanium did not contribute to improving the grindability of titanium. The Ti-30% Nb alloy exhibited significantly better grindability at low grinding speed with higher hardness, strength, and Young's modulus than titanium, presumably due to precipitation of the omega phase in the beta matrix.

Are new TiNbZr alloys potential substitutes of the Ti6Al4V alloy for dental applications? An electrochemical corrosion study.

Science.gov (United States)

Ribeiro, Ana Lúcia Roselino; Hammer, Peter; Vaz, Luís Geraldo; Rocha, Luís Augusto

2013-12-01

The main aim of this work was to assess the electrochemical behavior of new Ti35Nb5Zr and Ti35Nb10Zr alloys in artificial saliva at 37 °C to verify if they are indicated to be used as biomaterials in dentistry as alternatives to Ti6Al4V alloys in terms of corrosion protection efficiency of the material. Electrochemical impedance spectroscopy (EIS) experiments were carried out for different periods of time (0.5-216 h) in a three-electrode cell, where the working electrode (Ti alloys) was exposed to artificial saliva at 37 °C. The near-surface region of the alloys was investigated using x-ray photoelectron spectroscopy (XPS). All alloys exhibited an increase in corrosion potential with the immersion time, indicating the growth and stabilization of the passive film. Ti35Nb5Zr and Ti6Al4V alloys had their EIS results interpreted by a double-layer circuit, while the Ti35Nb10Zr alloy was modeled by a one-layer circuit. In general, the new TiNbZr alloys showed similar behavior to that observed for the Ti6Al4V. XPS results suggest, in the case of the TiNbZr alloys, the presence of a thicker passive layer containing a lower fraction of TiO2 phase than that of Ti6Al4V. After long-term immersion, all alloys develop a calcium phosphate phase on the surface. The new TiNbZr alloys appear as potential candidates to be used as a substitute to Ti6Al4V in the manufacturing of dental implant-abutment sets.

The Superconductors that Magnets Really Want: What Stands in the Way? (Superconductors for Accelerator Use: What Next and How Close is the Ideal Conductor?)

International Nuclear Information System (INIS)

Larbalestier, David

2009-01-01

There are over 5000 superconducting materials but only about 5 have ever been useful for applications in magnets, while HEP, which has been so vital for the development of superconducting magnet technology has made virtually every magnet out of just one, the simple bcc alloy Nb-Ti with Tc of 9 K and upper critical field ∼ 14T (at 2K). Significant demonstrations of the capability of the brittle intermetallic Nb3Sn have shown that fields of more than 15 T can be generated in dipole form. But Nb-Ti and Nb3Sn are staid, conventional superconductors, far from the cutting edge of superconducting science research where cuprates like YBa2Cu3O7-x and Bi2Sr2CaCu2Ox remain at the scientific forefront and in 2008 were joined by the recently discovered Fe-As pnictide superconductors. What could it mean to have materials for magnets with 10 times the Tc of Nb-Ti (90-120 K) and 3 or more times the critical field (100-240 T)? One enormous barrier is that higher Tc so far always means more complexity and a more localized superconducting interaction which is sensitive to local loss of superconductivity. The issue that has made the cuprate high temperature superconductors so hard to apply is that grain boundaries which form a 3D network in any practical wire form, easily acquire degraded superconducting properties. But conductors can now be made with extreme texture so that grain boundaries are minimized. Moreover almost practical conductors of Bi2Sr2CaCu2Ox and YBa2Cu3O7-x are now are in production and in late 2008 we were, at the Magnet Lab, able to make small solenoids operating at high current density in fields of 32 and almost 34 T respectively. Within the HEP community, there is enthusiasm to embrace HTS conductors for new very high field machines that could, like the Muon Collider, use fields of 30-50 T. In my talk I would like to explore the underlying science controlling such potential applications.

Determination of the electrostatic potential distribution in Pt/Fe:SrTiO₃/Nb:SrTiO₃ thin-film structures by electron holography.

Science.gov (United States)

Marchewka, Astrid; Cooper, David; Lenser, Christian; Menzel, Stephan; Du, Hongchu; Dittmann, Regina; Dunin-Borkowski, Rafal E; Waser, Rainer

2014-11-10

We determined the electrostatic potential distribution in pristine Pt/Fe:SrTiO3/Nb:SrTiO3 structures by electron holography experiments, revealing the existence of a depletion layer extending into the Nb-doped bottom electrode. Simulations of potential profiles in metal-insulator-metal structures were conducted assuming different types and distributions of dopants. It is found that the presence of acceptor-type dopant concentrations at the Fe:SrTiO3/Nb:SrTiO3 interface with a donor-doped insulating layer provides a good match to the measured profile. Such acceptor-type interface concentrations may be associated with Sr vacancies on the Nb:SrTiO3 side of the bottom interface.

Effect of Nb on glass forming ability and plasticity of (Ti-Cu)-based bulk metallic glasses

International Nuclear Information System (INIS)

Suo, Z.Y.; Qiu, K.Q.; Li, Q.F.; Ren, Y.L.; Hu, Z.Q.

2010-01-01

A Ti 33 Cu 47 Zr 9 Ni 6 Sn 2 Si 1 Nb 2 bulk metallic glass has been developed by Nb partial substitution for Zr in Ti 33 Cu 47 Zr 11 Ni 6 Sn 2 Si 1 alloy. The glass forming ability Ti 33 Cu 47 Zr 9 Ni 6 Sn 2 Si 1 Nb 2 alloy has been investigated using differential scanning calorimetry and X-ray diffractometry. Partial Nb substitutes for Zr promote the glass forming ability. Ti 33 Cu 47 Zr 9 Ni 6 Sn 2 Si 1 Nb 2 BMG with diameter of 3 mm can be fabricated by Cu-mold injection casting method. The glass forming ability of Ti 33 Cu 47 Zr 9 Ni 6 Sn 2 Si 1 Nb 2 alloy is enhanced by stabilizing the undercooled liquid against crystallization. The plastic strain up to 2.5% was obtained for Ti 33 Cu 47 Zr 9 Ni 6 Sn 2 Si 1 Nb 2 BMG compared to 0.15% for Ti 33 Cu 47 Zr 11 Ni 6 Sn 2 Si 1 BMG, which demonstrates that small amount of Nb addition can have a dramatic effect on plasticity enhancement in Ti-Cu-based BMG. The intersection and branching of the shear bands are observed. The plastic strain of the Ti 33 Cu 47 Zr 9 Ni 6 Sn 2 Si 1 Nb 2 BMG can be improved by the generation of nanocrystalline particles, which lead to multiple shear bands.

Selective Laser Melting of Ti-45Nb Alloy

Directory of Open Access Journals (Sweden)

Holger Schwab

2015-04-01

Full Text Available Ti-45Nb is one of the potential alloys that can be applied for biomedical applications as implants due to its low Young’s modulus. Ti-45Nb (wt.% gas atomized powders were used to produce bulk samples by selective laser melting with three different parameter sets (energy inputs. A β-phase microstructure consisting of elliptical grains with an enriched edge of titanium was observed by scanning electron microscopy and X-ray diffraction studies. The mechanical properties of these samples were evaluated using hardness and compression tests, which suggested that the strength of the samples increases with increasing energy input within the range considered.

Contributions to the study of superconducting multifilamentary composites and cables; Contributions a l`etude du comportement des composites et cables supraconducteurs

Energy Technology Data Exchange (ETDEWEB)

Turck, B

1992-03-01

This report is a collection of published papers in French and in English on superconducting composites and cables. All domains concerning the behaviour of superconductors in coils for field generation have been covered: critical current, current distribution, instabilities, losses in varying field. This document provides with expressions and criteria for conductor design, with conditions for achieving given performances and with criteria for design and optimization of structures of multifilamentary composites and cables. These publications have played a determining role in the understanding of the behaviour of superconductors and in their use in high performing magnets.

Mutual Effects of Hydrogenation and Deformation in Ti-Nb Alloys

National Research Council Canada - National Science Library

Zander, D

2002-01-01

...), transmission electron microscopy (TEM), thermal desorption spectroscopy (TDS), and microhardness tests, the influence of hydrogen at high fugacities on the phase stability, desorption behavior, and microhardness in Ti-Nb (20 to 45 wt pct Nb...

Stress-induced phase transformation and room temperature aging in Ti-Nb-Fe alloys

Energy Technology Data Exchange (ETDEWEB)

Cai, S.; Schaffer, J.E. [Fort Wayne Metals Research Products Corp, 9609 Ardmore Ave., Fort Wayne, IN 46809 (United States); Ren, Y. [Advanced Photon Source, Argonne National Laboratory, 9700 S. Cass Ave., Argonne, IL 60439 (United States)

2017-01-05

Room temperature deformation behavior of Ti-17Nb-1Fe and Ti-17Nb-2Fe alloys was studied by synchrotron X-ray diffraction and tensile testing. It was found that, after proper heat treatment, both alloys were able to recover a deformation strain of above 3.5% due to the Stress-induced Martensite (SIM) phase transformation. Higher Fe content increased the beta phase stability and onset stress for SIM transformation. A strong {110}{sub β} texture was produced in Ti-17Nb-2Fe compared to the {210}{sub β} texture that was observed in Ti-17Nb-1Fe. Room temperature aging was observed in both alloys, where the formation of the omega phase increased the yield strength (also SIM onset stress), and decreased the ductility and strain recovery. Other metastable beta Ti alloys may show a similar aging response and this should draw the attention of materials design engineers.

NbF5 and TaF5: Assignment of 19F NMR resonances and chemical bond analysis from GIPAW calculations

International Nuclear Information System (INIS)

Biswal, Mamata; Body, Monique; Legein, Christophe; Sadoc, Aymeric; Boucher, Florent

2013-01-01

The 19 F isotropic chemical shifts (δ iso ) of two isomorphic compounds, NbF 5 and TaF 5 , which involve six nonequivalent fluorine sites, have been experimentally determined from the reconstruction of 1D 19 F MAS NMR spectra. In parallel, the corresponding 19 F chemical shielding tensors have been calculated using the GIPAW method for both experimental and DFT-optimized structures. Furthermore, the [M 4 F 20 ] units of NbF 5 and TaF 5 being held together by van der Waals interactions, the relevance of Grimme corrections to the DFT optimization processes has been evaluated. However, the semi-empirical dispersion correction term introduced by such a method does not show any significant improvement. Nonetheless, a complete and convincing assignment of the 19 F NMR lines of NbF 5 and TaF 5 is obtained, ensured by the linearity between experimental 19 F δ iso values and calculated 19 F isotropic chemical shielding σ iso values. The effects of the geometry optimizations have been carefully analyzed, confirming among other matters, the inaccuracy of the experimental structure of NbF 5 . The relationships between the fluorine chemical shifts, the nature of the fluorine atoms (bridging or terminal), the position of the terminal ones (opposite or perpendicular to the bridging ones), the fluorine charges, the ionicity and the length of the M–F bonds have been established. Additionally, for three of the 19 F NMR lines of NbF 5 , distorted multiplets, arising from 1 J-coupling and residual dipolar coupling between the 19 F and 93 Nb nuclei, were simulated yielding to values of 93 Nb– 19 F 1 J-coupling for the corresponding fluorine sites. - Graphical abstract: The complete assignment of the 19 F NMR lines of NbF 5 and TaF 5 allow establishing relationships between the 19 F δ iso values, the nature of the fluorine atoms (bridging or terminal), the position of the terminal ones (opposite or perpendicular to the bridging ones), the fluorine charges, the ionicity and the

Thermal fluctuations in the classical superconductor Nb3Sn from high-resolution specific-heat measurements

International Nuclear Information System (INIS)

Lortz, Rolf; Wang Yuxing; Junod, Alain; Toyota, Naoki

2007-01-01

The range of thermal fluctuations in 'classical' bulk superconductors is extremely small and especially in low-fields hardly experimentally accessible. With a new type of calorimeter we were able to detect a tiny lambda anomaly in the specific-heat of the superconductor Nb 3 Sn within a narrow temperature range around the H c2 line. We show that the evolution of the anomaly as a function of magnetic field follows scaling laws expected in the presence of critical thermal fluctuations

Mechanical Properties of a Newly Additive Manufactured Implant Material Based on Ti-42Nb.

Science.gov (United States)

Schulze, Christian; Weinmann, Markus; Schweigel, Christoph; Keßler, Olaf; Bader, Rainer

2018-01-13

The application of Ti-6Al-4V alloy or commercially pure titanium for additive manufacturing enables the fabrication of complex structural implants and patient-specific implant geometries. However, the difference in Young's modulus of α + β-phase Ti alloys compared to the human bone promotes stress-shielding effects in the implant-bone interphase. The aim of the present study is the mechanical characterization of a new pre-alloyed β-phase Ti-42Nb alloy for application in additive manufacturing. The present investigation focuses on the mechanical properties of SLM-printed Ti-42Nb alloy in tensile and compression tests. In addition, the raw Ti-42Nb powder, the microstructure of the specimens prior to and after compression tests, as well as the fracture occurring in tensile tests are characterized by means of the SEM/EDX analysis. The Ti-42Nb raw powder exhibits a dendrite-like Ti-structure, which is melted layer-by-layer into a microstructure with a very homogeneous distribution of Nb and Ti during the SLM process. Tensile tests display Young's modulus of 60.51 ± 3.92 GPa and an ultimate tensile strength of 683.17 ± 16.67 MPa, whereas, under a compressive load, a compressive strength of 1330.74 ± 53.45 MPa is observed. The combination of high mechanical strength and low elastic modulus makes Ti-42Nb an interesting material for orthopedic and dental implants. The spherical shape of the pre-alloyed material additionally allows for application in metal 3D printing, enabling the fabrication of patient-specific structural implants.

Effect of Inoculant Alloy Selection and Particle Size on Efficiency of Isomorphic Inoculation of Ti-Al.

Science.gov (United States)

Kennedy, J R; Rouat, B; Daloz, D; Bouzy, E; Zollinger, J

2018-04-25

The process of isomorphic inoculation relies on precise selection of inoculant alloys for a given system. Three alloys, Ti-10Al-25Nb, Ti-25Al-10Ta, and Ti-47Ta (at %) were selected as potential isomorphic inoculants for a Ti-46Al alloy. The binary Ti-Ta alloy selected was found to be ineffective as an inoculant due to its large density difference with the melt, causing the particles to settle. Both ternary alloys were successfully implemented as isomorphic inoculants that decreased the equiaxed grain size and increased the equiaxed fraction in their ingots. The degree of grain refinement obtained was found to be dependent on the number of particles introduced to the melt. Also, more new grains were formed than particles added to the melt. The grains/particle efficiency varied from greater than one to nearly twenty as the size of the particle increased. This is attributed to the breaking up of particles into smaller particles by dissolution in the melt. For a given particle size, Ti-Al-Ta and Ti-Al-Nb particles were found to have a roughly similar grain/particle efficiency.

Are new TiNbZr alloys potential substitutes of the Ti6Al4V alloy for dental applications? An electrochemical corrosion study

International Nuclear Information System (INIS)

Ribeiro, Ana Lúcia Roselino; Hammer, Peter; Vaz, Luís Geraldo; Rocha, Luís Augusto

2013-01-01

The main aim of this work was to assess the electrochemical behavior of new Ti35Nb5Zr and Ti35Nb10Zr alloys in artificial saliva at 37 °C to verify if they are indicated to be used as biomaterials in dentistry as alternatives to Ti6Al4V alloys in terms of corrosion protection efficiency of the material. Electrochemical impedance spectroscopy (EIS) experiments were carried out for different periods of time (0.5–216 h) in a three-electrode cell, where the working electrode (Ti alloys) was exposed to artificial saliva at 37 °C. The near-surface region of the alloys was investigated using x-ray photoelectron spectroscopy (XPS). All alloys exhibited an increase in corrosion potential with the immersion time, indicating the growth and stabilization of the passive film. Ti35Nb5Zr and Ti6Al4V alloys had their EIS results interpreted by a double-layer circuit, while the Ti35Nb10Zr alloy was modeled by a one-layer circuit. In general, the new TiNbZr alloys showed similar behavior to that observed for the Ti6Al4V. XPS results suggest, in the case of the TiNbZr alloys, the presence of a thicker passive layer containing a lower fraction of TiO 2  phase than that of Ti6Al4V. After long-term immersion, all alloys develop a calcium phosphate phase on the surface. The new TiNbZr alloys appear as potential candidates to be used as a substitute to Ti6Al4V in the manufacturing of dental implant-abutment sets. (paper)