Heuristics for Multidimensional Packing Problems
DEFF Research Database (Denmark)
Egeblad, Jens
for a minimum height container required for the items. The main contributions of the thesis are three new heuristics for strip-packing and knapsack packing problems where items are both rectangular and irregular. In the two first papers we describe a heuristic for the multidimensional strip-packing problem...... that is based on a relaxed placement principle. The heuristic starts with a random overlapping placement of items and large container dimensions. From the overlapping placement overlap is reduced iteratively until a non-overlapping placement is found and a new problem is solved with a smaller container size...... of this heuristic are among the best published in the literature both for two- and three-dimensional strip-packing problems for irregular shapes. In the third paper, we introduce a heuristic for two- and three-dimensional rectangular knapsack packing problems. The two-dimensional heuristic uses the sequence pair...
Multi-dimensional Bin Packing Problems with Guillotine Constraints
DEFF Research Database (Denmark)
Amossen, Rasmus Resen; Pisinger, David
2010-01-01
The problem addressed in this paper is the decision problem of determining if a set of multi-dimensional rectangular boxes can be orthogonally packed into a rectangular bin while satisfying the requirement that the packing should be guillotine cuttable. That is, there should exist a series of face...... parallel straight cuts that can recursively cut the bin into pieces so that each piece contains a box and no box has been intersected by a cut. The unrestricted problem is known to be NP-hard. In this paper we present a generalization of a constructive algorithm for the multi-dimensional bin packing...... problem, with and without the guillotine constraint, based on constraint programming....
The Maximum Resource Bin Packing Problem
DEFF Research Database (Denmark)
Boyar, J.; Epstein, L.; Favrholdt, L.M.
2006-01-01
Usually, for bin packing problems, we try to minimize the number of bins used or in the case of the dual bin packing problem, maximize the number or total size of accepted items. This paper presents results for the opposite problems, where we would like to maximize the number of bins used...... algorithms, First-Fit-Increasing and First-Fit-Decreasing for the maximum resource variant of classical bin packing. For the on-line variant, we define maximum resource variants of classical and dual bin packing. For dual bin packing, no on-line algorithm is competitive. For classical bin packing, we find...
Perceptual Salience and Children's Multidimensional Problem Solving
Odom, Richard D.; Corbin, David W.
1973-01-01
Uni- and multidimensional processing of 6- to 9-year olds was studied using recall tasks in which an array of stimuli was reconstructed to match a model array. Results indicated that both age groups were able to solve multidimensional problems, but that solution rate was retarded by the unidimensional processing of highly salient dimensions.…
Bin-packing problems with load balancing and stability constraints
DEFF Research Database (Denmark)
Trivella, Alessio; Pisinger, David
apper in a wide range of disciplines, including transportation and logistics, computer science, engineering, economics and manufacturing. The problem is well-known to be N P-hard and difficult to solve in practice, especially when dealing with the multi-dimensional cases. Closely connected to the BPP...... realistic constraints related to e.g. load balancing, cargo stability and weight limits, in the multi-dimensional BPP. The BPP poses additional challenges compared to the CLP due to the supplementary objective of minimizing the number of bins. In particular, in section 2 we discuss how to integrate bin......-packing and load balancing of items. The problem has only been considered in the literature in simplified versions, e.g. balancing a single bin or introducing a feasible region for the barycenter. In section 3 we generalize the problem to handle cargo stability and weight constraints....
Generalized network improvement and packing problems
Holzhauser, Michael
2016-01-01
Michael Holzhauser discusses generalizations of well-known network flow and packing problems by additional or modified side constraints. By exploiting the inherent connection between the two problem classes, the author investigates the complexity and approximability of several novel network flow and packing problems and presents combinatorial solution and approximation algorithms. Contents Fractional Packing and Parametric Search Frameworks Budget-Constrained Minimum Cost Flows: The Continuous Case Budget-Constrained Minimum Cost Flows: The Discrete Case Generalized Processing Networks Convex Generalized Flows Target Groups Researchers and students in the fields of mathematics, computer science, and economics Practitioners in operations research and logistics The Author Dr. Michael Holzhauser studied computer science at the University of Kaiserslautern and is now a research fellow in the Optimization Research Group at the Department of Mathematics of the University of Kaiserslautern.
Multidimensional integral representations problems of analytic continuation
Kytmanov, Alexander M
2015-01-01
The monograph is devoted to integral representations for holomorphic functions in several complex variables, such as Bochner-Martinelli, Cauchy-Fantappiè, Koppelman, multidimensional logarithmic residue etc., and their boundary properties. The applications considered are problems of analytic continuation of functions from the boundary of a bounded domain in C^n. In contrast to the well-known Hartogs-Bochner theorem, this book investigates functions with the one-dimensional property of holomorphic extension along complex lines, and includes the problems of receiving multidimensional boundary analogs of the Morera theorem. This book is a valuable resource for specialists in complex analysis, theoretical physics, as well as graduate and postgraduate students with an understanding of standard university courses in complex, real and functional analysis, as well as algebra and geometry.
New method for solving multidimensional scattering problem
International Nuclear Information System (INIS)
Melezhik, V.S.
1991-01-01
A new method is developed for solving the quantum mechanical problem of scattering of a particle with internal structure. The multichannel scattering problem is formulated as a system of nonlinear functional equations for the wave function and reaction matrix. The method is successfully tested for the scattering from a nonspherical potential well and a long-range nonspherical scatterer. The method is also applicable to solving the multidimensional Schroedinger equation with a discrete spectrum. As an example the known problem of a hydrogen atom in a homogeneous magnetic field is analyzed
A Harmonic Algorithm for the 3D Strip Packing Problem
N. Bansal (Nikhil); X. Han; K. Iwama; M. Sviridenko; G. Zhang (Guochuan)
2013-01-01
htmlabstractIn the three-dimensional (3D) strip packing problem, we are given a set of 3D rectangular items and a 3D box $B$. The goal is to pack all the items in $B$ such that the height of the packing is minimized. We consider the most basic version of the problem, where the items must be packed
Comparing Online Algorithms for Bin Packing Problems
DEFF Research Database (Denmark)
Epstein, Leah; Favrholdt, Lene Monrad; Kohrt, Jens Svalgaard
2012-01-01
The relative worst-order ratio is a measure of the quality of online algorithms. In contrast to the competitive ratio, this measure compares two online algorithms directly instead of using an intermediate comparison with an optimal offline algorithm. In this paper, we apply the relative worst-ord......-order ratio to online algorithms for several common variants of the bin packing problem. We mainly consider pairs of algorithms that are not distinguished by the competitive ratio and show that the relative worst-order ratio prefers the intuitively better algorithm of each pair....
Packing in Two and Three Dimensions
National Research Council Canada - National Science Library
Martins, Gustavo H
2003-01-01
...), the Multidimensional Knapsack Problem (MD-KP), and the Multidimensional Bin Packing Problem (MD-BPP). In these problems, there is a set of items, with rectangular dimensions, and a set of large containers, or bins, also with rectangular dimensions...
Modified strip packing heuristics for the rectangular variable-sized bin packing problem
Directory of Open Access Journals (Sweden)
FG Ortmann
2010-06-01
Full Text Available Two packing problems are considered in this paper, namely the well-known strip packing problem (SPP and the variable-sized bin packing problem (VSBPP. A total of 252 strip packing heuristics (and variations thereof from the literature, as well as novel heuristics proposed by the authors, are compared statistically by means of 1170 SPP benchmark instances in order to identify the best heuristics in various classes. A combination of new heuristics with a new sorting method yields the best results. These heuristics are combined with a previous heuristic for the VSBPP by the authors to find good feasible solutions to 1357 VSBPP benchmark instances. This is the largest statistical comparison of algorithms for the SPP and the VSBPP to the best knowledge of the authors.
Integrating packing and distribution problems and optimization through mathematical programming
Directory of Open Access Journals (Sweden)
Fabio Miguel
2016-06-01
Full Text Available This paper analyzes the integration of two combinatorial problems that frequently arise in production and distribution systems. One is the Bin Packing Problem (BPP problem, which involves finding an ordering of some objects of different volumes to be packed into the minimal number of containers of the same or different size. An optimal solution to this NP-Hard problem can be approximated by means of meta-heuristic methods. On the other hand, we consider the Capacitated Vehicle Routing Problem with Time Windows (CVRPTW, which is a variant of the Travelling Salesman Problem (again a NP-Hard problem with extra constraints. Here we model those two problems in a single framework and use an evolutionary meta-heuristics to solve them jointly. Furthermore, we use data from a real world company as a test-bed for the method introduced here.
Decay rate in a multi-dimensional fission problem
Energy Technology Data Exchange (ETDEWEB)
Brink, D M; Canto, L F
1986-06-01
The multi-dimensional diffusion approach of Zhang Jing Shang and Weidenmueller (1983 Phys. Rev. C28, 2190) is used to study a simplified model for induced fission. In this model it is shown that the coupling of the fission coordinate to the intrinsic degrees of freedom is equivalent to an extra friction and a mass correction in the corresponding one-dimensional problem.
A Heuristic Algorithm for Solving Triangle Packing Problem
Directory of Open Access Journals (Sweden)
Ruimin Wang
2013-01-01
Full Text Available The research on the triangle packing problem has important theoretic significance, which has broad application prospects in material processing, network resource optimization, and so forth. Generally speaking, the orientation of the triangle should be limited in advance, since the triangle packing problem is NP-hard and has continuous properties. For example, the polygon is not allowed to rotate; then, the approximate solution can be obtained by optimization method. This paper studies the triangle packing problem by a new kind of method. Such concepts as angle region, corner-occupying action, corner-occupying strategy, and edge-conjoining strategy are presented in this paper. In addition, an edge-conjoining and corner-occupying algorithm is designed, which is to obtain an approximate solution. It is demonstrated that the proposed algorithm is highly efficient, and by the time complexity analysis and the analogue experiment result is found.
The 'thousand words' problem: Summarizing multi-dimensional data
International Nuclear Information System (INIS)
Scott, David M.
2011-01-01
Research highlights: → Sophisticated process sensors produce large multi-dimensional data sets. → Plant control systems cannot handle images or large amounts of data. → Various techniques reduce the dimensionality, extracting information from raw data. → Simple 1D and 2D methods can often be extended to 3D and 4D applications. - Abstract: An inherent difficulty in the application of multi-dimensional sensing to process monitoring and control is the extraction and interpretation of useful information. Ultimately the measured data must be collapsed into a relatively small number of values that capture the salient characteristics of the process. Although multiple dimensions are frequently necessary to isolate a particular physical attribute (such as the distribution of a particular chemical species in a reactor), plant control systems are not equipped to use such data directly. The production of a multi-dimensional data set (often displayed as an image) is not the final step of the measurement process, because information must still be extracted from the raw data. In the metaphor of one picture being equal to a thousand words, the problem becomes one of paraphrasing a lengthy description of the image with one or two well-chosen words. Various approaches to solving this problem are discussed using examples from the fields of particle characterization, image processing, and process tomography.
Bin packing problem solution through a deterministic weighted finite automaton
Zavala-Díaz, J. C.; Pérez-Ortega, J.; Martínez-Rebollar, A.; Almanza-Ortega, N. N.; Hidalgo-Reyes, M.
2016-06-01
In this article the solution of Bin Packing problem of one dimension through a weighted finite automaton is presented. Construction of the automaton and its application to solve three different instances, one synthetic data and two benchmarks are presented: N1C1W1_A.BPP belonging to data set Set_1; and BPP13.BPP belonging to hard28. The optimal solution of synthetic data is obtained. In the first benchmark the solution obtained is one more container than the ideal number of containers and in the second benchmark the solution is two more containers than the ideal solution (approximately 2.5%). The runtime in all three cases was less than one second.
Conservation laws for multidimensional systems and related linear algebra problems
Igonine, Sergei
2002-01-01
We consider multidimensional systems of PDEs of generalized evolution form with t-derivatives of arbitrary order on the left-hand side and with the right-hand side dependent on lower order t-derivatives and arbitrary space derivatives. For such systems we find an explicit necessary condition for the
Conservation laws for multidimensional systems and related linear algebra problems
Igonin, S.
2002-01-01
We consider multidimensional systems of PDEs of generalized evolution form with $t$-derivatives of arbitrary order on the left-hand side and with the right-hand side dependent on lower order $t$-derivatives and arbitrary space derivatives. For such systems we find an explicit necessary condition for
An experimental comparison of some heuristics for cardinality constrained bin packing problem
Directory of Open Access Journals (Sweden)
Maja Remic
2012-01-01
Full Text Available Background: Bin packing is an NPhard optimization problem of packing items of given sizes into minimum number of capacitylimited bins. Besides the basic problem, numerous other variants of bin packing exist. The cardinality constrained bin packing adds an additional constraint that the number of items in a bin must not exceed a given limit Nmax. Objectives: Goal of the paper is to present a preliminary experimental study which demostrates adaptations of the new algorithms to the general cardinality constrained bin packing problem. Methods/Approach: Straightforward modifications of First Fit Decreasing (FFD, Refined First Fit (RFF and the algorithm by Zhang et al. for the bin packing problem are compared to four cardinality constrained bin packing problem specific algorithms on random lists of items with 0%, 10%, 30% and 50% of large items. The behaviour of all algorithms when cardinality constraint Nmax increases is also studied. Results: Results show that all specific algorithms outperform the general algorithms on lists with low percentage of big items. Conclusions: One of the specific algorithms performs better or equally well even on lists with high percentage of big items and is therefore of significant interest. The behaviour when Nmax increases shows that specific algorithms can be used for solving the general bin packing problem as well.
Application of Genetic Algorithm for the Bin Packing Problem with a New Representation Scheme
Directory of Open Access Journals (Sweden)
N. Mohamadi
2010-10-01
Full Text Available The Bin Packing Problem (BPP is to find the minimum number of binsneeded to pack a given set of objects of known sizes so that they donot exceed the capacity of each bin. This problem is known to beNP-Hard [5]; hence many heuristic procedures for its solution havebeen suggested. In this paper we propose a new representation schemeand solve the problem by a Genetic Algorithm. Limited computationalresults show the efficiency of this scheme.
Augmented neural networks and problem structure-based heuristics for the bin-packing problem
Kasap, Nihat; Agarwal, Anurag
2012-08-01
In this article, we report on a research project where we applied augmented-neural-networks (AugNNs) approach for solving the classical bin-packing problem (BPP). AugNN is a metaheuristic that combines a priority rule heuristic with the iterative search approach of neural networks to generate good solutions fast. This is the first time this approach has been applied to the BPP. We also propose a decomposition approach for solving harder BPP, in which subproblems are solved using a combination of AugNN approach and heuristics that exploit the problem structure. We discuss the characteristics of problems on which such problem structure-based heuristics could be applied. We empirically show the effectiveness of the AugNN and the decomposition approach on many benchmark problems in the literature. For the 1210 benchmark problems tested, 917 problems were solved to optimality and the average gap between the obtained solution and the upper bound for all the problems was reduced to under 0.66% and computation time averaged below 33 s per problem. We also discuss the computational complexity of our approach.
Visual nesting system for irregular cutting-stock problem based on rubber band packing algorithm
Directory of Open Access Journals (Sweden)
Xiaoping Liao
2016-05-01
Full Text Available This article deals with the packing problem of irregular items allocated into a rectangular sheet to minimize the waste. Conventional solution is not visual during the packing process. It obtains a reasonable and relatively satisfactory solution between the nesting time and nesting solution. This article adopts a physical method that uses rubber band packing algorithm to simulate a rubber band wrapping those packing irregular items. The simulation shows a visual and fast packing process. The resultant rubber band force is applied in the packing items to translate, rotate, and slide them to make the area decrease and obtain a high packing density. An improved analogy QuickHull algorithm is presented to obtain extreme points of rubber band convex hull. An adaptive module could set a variable rubber band force and a variable time step to make a proper convergence and no intersection. A quick convex decomposition method is used to solve the problem of concave polygon. A plural vector expression approach is adopted to calculate the resultant vector of the rubber band force. Several cases are compared with the benchmark problems to prove rubber band packing algorithm performance.
Conservation laws for multidimensional systems and related linear algebra problems
International Nuclear Information System (INIS)
Igonin, Sergei
2002-01-01
We consider multidimensional systems of PDEs of generalized evolution form with t-derivatives of arbitrary order on the left-hand side and with the right-hand side dependent on lower order t-derivatives and arbitrary space derivatives. For such systems we find an explicit necessary condition for the existence of higher conservation laws in terms of the system's symbol. For systems that violate this condition we give an effective upper bound on the order of conservation laws. Using this result, we completely describe conservation laws for viscous transonic equations, for the Brusselator model and the Belousov-Zhabotinskii system. To achieve this, we solve over an arbitrary field the matrix equations SA=A t S and SA=-A t S for a quadratic matrix A and its transpose A t , which may be of independent interest
Balsara, Dinshaw S.; Nkonga, Boniface
2017-10-01
Just as the quality of a one-dimensional approximate Riemann solver is improved by the inclusion of internal sub-structure, the quality of a multidimensional Riemann solver is also similarly improved. Such multidimensional Riemann problems arise when multiple states come together at the vertex of a mesh. The interaction of the resulting one-dimensional Riemann problems gives rise to a strongly-interacting state. We wish to endow this strongly-interacting state with physically-motivated sub-structure. The fastest way of endowing such sub-structure consists of making a multidimensional extension of the HLLI Riemann solver for hyperbolic conservation laws. Presenting such a multidimensional analogue of the HLLI Riemann solver with linear sub-structure for use on structured meshes is the goal of this work. The multidimensional MuSIC Riemann solver documented here is universal in the sense that it can be applied to any hyperbolic conservation law. The multidimensional Riemann solver is made to be consistent with constraints that emerge naturally from the Galerkin projection of the self-similar states within the wave model. When the full eigenstructure in both directions is used in the present Riemann solver, it becomes a complete Riemann solver in a multidimensional sense. I.e., all the intermediate waves are represented in the multidimensional wave model. The work also presents, for the very first time, an important analysis of the dissipation characteristics of multidimensional Riemann solvers. The present Riemann solver results in the most efficient implementation of a multidimensional Riemann solver with sub-structure. Because it preserves stationary linearly degenerate waves, it might also help with well-balancing. Implementation-related details are presented in pointwise fashion for the one-dimensional HLLI Riemann solver as well as the multidimensional MuSIC Riemann solver.
Secondary Channel Bifurcation Geometry: A Multi-dimensional Problem
Gaeuman, D.; Stewart, R. L.
2017-12-01
The construction of secondary channels (or side channels) is a popular strategy for increasing aquatic habitat complexity in managed rivers. Such channels, however, frequently experience aggradation that prevents surface water from entering the side channels near their bifurcation points during periods of relatively low discharge. This failure to maintain an uninterrupted surface water connection with the main channel can reduce the habitat value of side channels for fish species that prefer lotic conditions. Various factors have been proposed as potential controls on the fate of side channels, including water surface slope differences between the main and secondary channels, the presence of main channel secondary circulation, transverse bed slopes, and bifurcation angle. A quantitative assessment of more than 50 natural and constructed secondary channels in the Trinity River of northern California indicates that bifurcations can assume a variety of configurations that are formed by different processes and whose longevity is governed by different sets of factors. Moreover, factors such as bifurcation angle and water surface slope vary with discharge level and are continuously distributed in space, such that they must be viewed as a multi-dimensional field rather than a single-valued attribute that can be assigned to a particular bifurcation.
Nonlinear Multidimensional Assignment Problems Efficient Conic Optimization Methods and Applications
2015-06-24
WORK UNIT NUMBER 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS(ES) Arizona State University School of Mathematical & Statistical Sciences 901 S...SUPPLEMENTARY NOTES 14. ABSTRACT The major goals of this project were completed: the exact solution of previously unsolved challenging combinatorial optimization... combinatorial optimization problem, the Directional Sensor Problem, was solved in two ways. First, heuristically in an engineering fashion and second, exactly
Hopwood, Christopher J.; Burt, S. Alexandra; Keel, Pamela K.; Neale, Michael C.; Boker, Steven M.; Klump, Kelly L.
2013-01-01
Personality traits are known to be associated with a host of important life outcomes, including interpersonal dysfunction. The interpersonal circumplex offers a comprehensive system for articulating the kinds of interpersonal problems associated with personality traits. In the current study, traits as measured by the Multidimensional Personality…
Solving non-standard packing problems by global optimization and heuristics
Fasano, Giorgio
2014-01-01
This book results from a long-term research effort aimed at tackling complex non-standard packing issues which arise in space engineering. The main research objective is to optimize cargo loading and arrangement, in compliance with a set of stringent rules. Complicated geometrical aspects are also taken into account, in addition to balancing conditions based on attitude control specifications. Chapter 1 introduces the class of non-standard packing problems studied. Chapter 2 gives a detailed explanation of a general model for the orthogonal packing of tetris-like items in a convex domain. A number of additional conditions are looked at in depth, including the prefixed orientation of subsets of items, the presence of unusable holes, separation planes and structural elements, relative distance bounds as well as static and dynamic balancing requirements. The relative feasibility sub-problem which is a special case that does not have an optimization criterion is discussed in Chapter 3. This setting can be exploit...
Directory of Open Access Journals (Sweden)
Terry Noviar Panggabean
2016-08-01
Full Text Available Abstrak—Karna representasi abstrak dari beberapa sistem pengambilan keputusan yang nyata dalam kehidupan sehari hari membuat masalah optimasi kombinatorial umumnya sangat sulit untuk dipecahkan. Bin packing problem ialah solusi terbaik dalam mengatasi masalah optimasi kombinatorial, yang digunakan untuk mencari sebuah objek secara optimal dari sekelompok himpunan objek yang berhingga. Serangkaian pendekatan hybrid telah dikembangkan dalam hal ini untuk memecahkan masalah Bin Packing. Metaheuristik adalah salah satu pendekatan tingkat tinggi dalam memandu dalam memodifikasi beberapa metode heuristik lainnya untuk mencari tingkat optimasi yang lebih baik. Genetic Algorithm atau Algoritma Genetika juga merupakan metode metaheuristik yang digunakan untuk menyelesaikan berbagai masalah dalam hal peningkatan optimasi. Dalam algoritma genetika terdapat bermacam-macam varian. Dalam penelitian dipaparkan mengenai taksonomi dari algoritma genetika parallel (Parallel Genetic Algorithm yang memiliki kemampuan yang lebih baik dari algoritma genetika konvensional dalam hal kinerja dan skalabilitasnya. Tetapi algoritma genetika paralel ini hanya cocok untuk permasalahan jaringan komputer heterogen dan sistem terdistribusi. Berdasarkan penelitian yang sudah pernah dilakukan sebelumnya dan dari uraian diatas maka penulis tertarik untuk melakukan penelitian bagaimana menerapkan hukum ketetapan Hardy-Weinberg dari bidang biologi kedalam algoritma genetika melakukan analisis tingkat optimasi terhadap Bin Packing Problem.. Keywords— Genetic Algortihm, Hardy-Weinberg, Bin Packing Problem.
International Nuclear Information System (INIS)
Downar, T.
2009-01-01
The overall objective of the work here has been to eliminate the approximations used in current resonance treatments by developing continuous energy multi-dimensional transport calculations for problem dependent self-shielding calculations. The work here builds on the existing resonance treatment capabilities in the ORNL SCALE code system. The overall objective of the work here has been to eliminate the approximations used in current resonance treatments by developing continuous energy multidimensional transport calculations for problem dependent self-shielding calculations. The work here builds on the existing resonance treatment capabilities in the ORNL SCALE code system. Specifically, the methods here utilize the existing continuous energy SCALE5 module, CENTRM, and the multi-dimensional discrete ordinates solver, NEWT to develop a new code, CENTRM( ) NEWT. The work here addresses specific theoretical limitations in existing CENTRM resonance treatment, as well as investigates advanced numerical and parallel computing algorithms for CENTRM and NEWT in order to reduce the computational burden. The result of the work here will be a new computer code capable of performing problem dependent self-shielding analysis for both existing and proposed GENIV fuel designs. The objective of the work was to have an immediate impact on the safety analysis of existing reactors through improvements in the calculation of fuel temperature effects, as well as on the analysis of more sophisticated GENIV/NGNP systems through improvements in the depletion/transmutation of actinides for Advanced Fuel Cycle Initiatives.
Shiangjen, Kanokwatt; Chaijaruwanich, Jeerayut; Srisujjalertwaja, Wijak; Unachak, Prakarn; Somhom, Samerkae
2018-02-01
This article presents an efficient heuristic placement algorithm, namely, a bidirectional heuristic placement, for solving the two-dimensional rectangular knapsack packing problem. The heuristic demonstrates ways to maximize space utilization by fitting the appropriate rectangle from both sides of the wall of the current residual space layer by layer. The iterative local search along with a shift strategy is developed and applied to the heuristic to balance the exploitation and exploration tasks in the solution space without the tuning of any parameters. The experimental results on many scales of packing problems show that this approach can produce high-quality solutions for most of the benchmark datasets, especially for large-scale problems, within a reasonable duration of computational time.
The Planar Sandwich and Other 1D Planar Heat Flow Test Problems in ExactPack
Energy Technology Data Exchange (ETDEWEB)
Singleton, Jr., Robert [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)
2017-01-24
This report documents the implementation of several related 1D heat flow problems in the verification package ExactPack [1]. In particular, the planar sandwich class defined in Ref. [2], as well as the classes PlanarSandwichHot, PlanarSandwichHalf, and other generalizations of the planar sandwich problem, are defined and documented here. A rather general treatment of 1D heat flow is presented, whose main results have been implemented in the class Rod1D. All planar sandwich classes are derived from the parent class Rod1D.
International Nuclear Information System (INIS)
Vaganov, P.A.; Kol'tsov, A.A.; Kulikov, V.D.; Mejer, V.A.
1983-01-01
The multi-element instrumental neutron activation analysis of samples of mountain rocks (sandstones, aleurolites and shales of one of gold deposits) is performed. The spectra of irradiated samples are measured by Ge(Li) detector of the volume of 35 mm 3 . The content of 22 chemical elements is determined in each sample. The results of analysis serve as reliable basis for multi-dimensional statistic information processing, they constitute the basis for the generalized characteristics of rocks which brings about the solution of classification problem for rocks of different deposits
Solution of the Dirichlet Problem for the Poisson's Equation in a Multidimensional Infinite Layer
Directory of Open Access Journals (Sweden)
O. D. Algazin
2015-01-01
Full Text Available The paper considers the multidimensional Poisson equation in the domain bounded by two parallel hyperplanes (in the multidimensional infinite layer. For an n-dimensional half-space method of solving boundary value problems for linear partial differential equations with constant coefficients is a Fourier transform to the variables in the boundary hyperplane. The same method can be used for an infinite layer, as is done in this paper in the case of the Dirichlet problem for the Poisson equation. For strip and infinite layer in three-dimensional space the solutions of this problem are known. And in the three-dimensional case Green's function is written as an infinite series. In this paper, the solution is obtained in the integral form and kernels of integrals are expressed in a finite form in terms of elementary functions and Bessel functions. A recurrence relation between the kernels of integrals for n-dimensional and (n + 2 -dimensional layers was obtained. In particular, is built the Green's function of the Laplace operator for the Dirichlet problem, through which the solution of the problem is recorded. Even in three-dimensional case we obtained new formula compared to the known. It is shown that the kernel of the integral representation of the solution of the Dirichlet problem for a homogeneous Poisson equation (Laplace equation is an approximate identity (δ-shaped system of functions. Therefore, if the boundary values are generalized functions of slow growth, the solution of the Dirichlet problem for the homogeneous equation (Laplace is written as a convolution of kernels with these functions.
Lau, Chun Sing
This thesis studies two types of problems in financial derivatives pricing. The first type is the free boundary problem, which can be formulated as a partial differential equation (PDE) subject to a set of free boundary condition. Although the functional form of the free boundary condition is given explicitly, the location of the free boundary is unknown and can only be determined implicitly by imposing continuity conditions on the solution. Two specific problems are studied in details, namely the valuation of fixed-rate mortgages and CEV American options. The second type is the multi-dimensional problem, which involves multiple correlated stochastic variables and their governing PDE. One typical problem we focus on is the valuation of basket-spread options, whose underlying asset prices are driven by correlated geometric Brownian motions (GBMs). Analytic approximate solutions are derived for each of these three problems. For each of the two free boundary problems, we propose a parametric moving boundary to approximate the unknown free boundary, so that the original problem transforms into a moving boundary problem which can be solved analytically. The governing parameter of the moving boundary is determined by imposing the first derivative continuity condition on the solution. The analytic form of the solution allows the price and the hedging parameters to be computed very efficiently. When compared against the benchmark finite-difference method, the computational time is significantly reduced without compromising the accuracy. The multi-stage scheme further allows the approximate results to systematically converge to the benchmark results as one recasts the moving boundary into a piecewise smooth continuous function. For the multi-dimensional problem, we generalize the Kirk (1995) approximate two-asset spread option formula to the case of multi-asset basket-spread option. Since the final formula is in closed form, all the hedging parameters can also be derived in
International Nuclear Information System (INIS)
Beauchard, K; Cannarsa, P; Yamamoto, M
2014-01-01
The approach to Lipschitz stability for uniformly parabolic equations introduced by Imanuvilov and Yamamoto in 1998 based on Carleman estimates, seems hard to apply to the case of Grushin-type operators of interest to this paper. Indeed, such estimates are still missing for parabolic operators degenerating in the interior of the space domain. Nevertheless, we are able to prove Lipschitz stability results for inverse source problems for such operators, with locally distributed measurements in an arbitrary space dimension. For this purpose, we follow a mixed strategy which combines the approach due to Lebeau and Robbiano, relying on Fourier decomposition and Carleman inequalities for heat equations with non-smooth coefficients (solved by the Fourier modes). As a corollary, we obtain a direct proof of the observability of multidimensional Grushin-type parabolic equations, with locally distributed observations—which is equivalent to null controllability with locally distributed controls. (paper)
International Nuclear Information System (INIS)
Blanc, Gilles
1996-01-01
This work is devoted to the solution of the inverse multidimensional heat conduction problem. The first part is the determination of a methodology for determining the minimum number of sensors and the best sensor locations. The method is applied to a 20 problem but the extension to 30 problems is quite obvious. This methodology is based on the study of the rate of representation. This new concept allows to determine the quantity and the quality of the information obtain from the various sensors. The rate of representation is a useful tool for experimental design. lt can be determined very quickly by the transposed matrix method. This approach was validated with an experimental set-up. The second part is the development of a method that uses thermal strain measurement instead of temperature measurements to estimate the unknown thermal boundary conditions. We showed that this new sensor has two advantages in comparison with the classical temperature measurements: higher frequency can be estimated and smaller number of sensors can be used for 20 problems. The main weakness is, presently, the fact that the method can only be applied to beams. The results obtained from the numerical simulations were validated by the analysis of experimental data obtained on an experimental set-up especially designed and built for this study. (author) [fr
Heuristics for the Variable Sized Bin Packing Problem Using a Hybrid P-System and CUDA Architecture
AlEnezi, Qadha'a; AboElFotoh, Hosam; AlBdaiwi, Bader; AlMulla, Mohammad Ali
2016-01-01
The Variable Sized Bin Packing Problem has a wide range of application areas including packing, scheduling, and manufacturing. Given a list of items and variable sized bin types, the objective is to minimize the total size of the used bins. This problem is known to be NP-hard. In this article, we present two new heuristics for solving the problem using a new variation of P systems with active membranes, which we call a hybrid P system, implemented in CUDA. Our hybrid P-system model allows usi...
Balsara, Dinshaw S.; Dumbser, Michael
2015-04-01
Multidimensional Riemann solvers that have internal sub-structure in the strongly-interacting state have been formulated recently (D.S. Balsara (2012, 2014) [5,16]). Any multidimensional Riemann solver operates at the grid vertices and takes as its input all the states from its surrounding elements. It yields as its output an approximation of the strongly interacting state, as well as the numerical fluxes. The multidimensional Riemann problem produces a self-similar strongly-interacting state which is the result of several one-dimensional Riemann problems interacting with each other. To compute this strongly interacting state and its higher order moments we propose the use of a Galerkin-type formulation to compute the strongly interacting state and its higher order moments in terms of similarity variables. The use of substructure in the Riemann problem reduces numerical dissipation and, therefore, allows a better preservation of flow structures, like contact and shear waves. In this second part of a series of papers we describe how this technique is extended to unstructured triangular meshes. All necessary details for a practical computer code implementation are discussed. In particular, we explicitly present all the issues related to computational geometry. Because these Riemann solvers are Multidimensional and have Self-similar strongly-Interacting states that are obtained by Consistency with the conservation law, we call them MuSIC Riemann solvers. (A video introduction to multidimensional Riemann solvers is available on http://www.elsevier.com/xml/linking-roles/text/html". The MuSIC framework is sufficiently general to handle general nonlinear systems of hyperbolic conservation laws in multiple space dimensions. It can also accommodate all self-similar one-dimensional Riemann solvers and subsequently produces a multidimensional version of the same. In this paper we focus on unstructured triangular meshes. As examples of different systems of conservation laws we
International Nuclear Information System (INIS)
Dinh Nho Hao; Nguyen Trung Thanh; Sahli, Hichem
2008-01-01
In this paper we consider a multi-dimensional inverse heat conduction problem with time-dependent coefficients in a box, which is well-known to be severely ill-posed, by a variational method. The gradient of the functional to be minimized is obtained by aids of an adjoint problem and the conjugate gradient method with a stopping rule is then applied to this ill-posed optimization problem. To enhance the stability and the accuracy of the numerical solution to the problem we apply this scheme to the discretized inverse problem rather than to the continuous one. The difficulties with large dimensions of discretized problems are overcome by a splitting method which only requires the solution of easy-to-solve one-dimensional problems. The numerical results provided by our method are very good and the techniques seem to be very promising.
Cardinality reasoning for bin-packing constraint : Application to a tank allocation problem
Schaus, Pierre; Régin, Jean Charles; Van Schaeren, Rowan; Dullaert, Wout; Raa, Birger
2012-01-01
Flow reasoning has been successfully used in CP for more than a decade. It was originally introduced by Régin in the well-known Alldifferent and Global Cardinality Constraint (GCC) available in most of the CP solvers. The BinPacking constraint was introduced by Shaw and mainly uses an independent
International Nuclear Information System (INIS)
Capilla, M.; Talavera, C.F.; Ginestar, D.; Verdú, G.
2012-01-01
Highlights: ► The multidimensional P L approximation to the nuclear transport equation is reviewed. ► A nodal collocation method is developed for the spatial discretization of P L equations. ► Advantages of the method are lower dimension and good characterists of the associated algebraic eigenvalue problem. ► The P L nodal collocation method is implemented into the computer code SHNC. ► The SHNC code is verified with 2D and 3D benchmark eigenvalue problems from Takeda and Ikeda, giving satisfactory results. - Abstract: P L equations are classical approximations to the neutron transport equations, which are obtained expanding the angular neutron flux in terms of spherical harmonics. These approximations are useful to study the behavior of reactor cores with complex fuel assemblies, for the homogenization of nuclear cross-sections, etc., and most of these applications are in three-dimensional (3D) geometries. In this work, we review the multi-dimensional P L equations and describe a nodal collocation method for the spatial discretization of these equations for arbitrary odd order L, which is based on the expansion of the spatial dependence of the fields in terms of orthonormal Legendre polynomials. The performance of the nodal collocation method is studied by means of obtaining the k eff and the stationary power distribution of several 3D benchmark problems. The solutions are obtained are compared with a finite element method and a Monte Carlo method.
A symmetrized quasi-diffusion method for solving multidimensional transport problems
International Nuclear Information System (INIS)
Miften, M.M.; Larsen, E.W.
1992-01-01
In this paper, the authors propose a 'symmetrized' QD (SQD) method in which the non-self-adjoint QD diffusion problem is replaced by two self-adjoint diffusion problems. These problems are more easily discretized and more efficiently solved than in the standard QD method. They also give SQD calculational results for transport problems in x-y geometry
International Nuclear Information System (INIS)
Verdu, G.; Capilla, M.; Talavera, C. F.; Ginestar, D.
2012-01-01
PL equations are classical high order approximations to the transport equations which are based on the expansion of the angular dependence of the angular neutron flux and the nuclear cross sections in terms of spherical harmonics. A nodal collocation method is used to discretize the PL equations associated with a neutron source transport problem. The performance of the method is tested solving two 1D problems with analytical solution for the transport equation and a classical 2D problem. (authors)
Energy Technology Data Exchange (ETDEWEB)
Verdu, G. [Departamento de Ingenieria Quimica Y Nuclear, Universitat Politecnica de Valencia, Cami de Vera, 14, 46022. Valencia (Spain); Capilla, M.; Talavera, C. F.; Ginestar, D. [Dept. of Nuclear Engineering, Departamento de Matematica Aplicada, Universitat Politecnica de Valencia, Cami de Vera, 14, 46022. Valencia (Spain)
2012-07-01
PL equations are classical high order approximations to the transport equations which are based on the expansion of the angular dependence of the angular neutron flux and the nuclear cross sections in terms of spherical harmonics. A nodal collocation method is used to discretize the PL equations associated with a neutron source transport problem. The performance of the method is tested solving two 1D problems with analytical solution for the transport equation and a classical 2D problem. (authors)
[The immuno-endocrine system. A new endocrine theory: the problem of the packed transport].
Csaba, György
2011-05-15
Since the eighties of the last century hormone content was justified in immune cells (lymphocytes, granulocytes, monocytes, macrophages and mast cells), which produce, store and secrete these hormones. Although the amount of these materials in immune cells is relatively small, the mass of the producers (immune cells) is so large, that the phenomenon must be considered from endocrinological point of view, underlying the important differences between the "classical" and immuno-endocrine systems. Cells of the classic (built-in) endocrine system are mono-producers, while immune cells can synthesize many types of hormones (polyproducers). In addition, these cells can transport the whole hormone-producing machinery to the site of need, producing a local effect. This can be observed, for example, in the case of endorphin producing immune cells during inflammation and during early pregnancy around the chorionic villi. Hormone producing immune cells also have receptors for many hormones, so that they are poly-receivers. Via hormone producing and receiving capacity there is a bidirectional connection between the neuro-endocrine and immuno-endocrine systems. In addition, there is a network inside the immuno-endocrine system. The packed transport theory attempts to explain the mechanism and importance of the immuno-endocrine system.
Drake, John H; Özcan, Ender; Burke, Edmund K
2016-01-01
Hyper-heuristics are high-level methodologies for solving complex problems that operate on a search space of heuristics. In a selection hyper-heuristic framework, a heuristic is chosen from an existing set of low-level heuristics and applied to the current solution to produce a new solution at each point in the search. The use of crossover low-level heuristics is possible in an increasing number of general-purpose hyper-heuristic tools such as HyFlex and Hyperion. However, little work has been undertaken to assess how best to utilise it. Since a single-point search hyper-heuristic operates on a single candidate solution, and two candidate solutions are required for crossover, a mechanism is required to control the choice of the other solution. The frameworks we propose maintain a list of potential solutions for use in crossover. We investigate the use of such lists at two conceptual levels. First, crossover is controlled at the hyper-heuristic level where no problem-specific information is required. Second, it is controlled at the problem domain level where problem-specific information is used to produce good-quality solutions to use in crossover. A number of selection hyper-heuristics are compared using these frameworks over three benchmark libraries with varying properties for an NP-hard optimisation problem: the multidimensional 0-1 knapsack problem. It is shown that allowing crossover to be managed at the domain level outperforms managing crossover at the hyper-heuristic level in this problem domain.
International Nuclear Information System (INIS)
Warsa, James S.; Wareing, Todd A.; Morel, Jim E.
2004-01-01
A loss in the effectiveness of diffusion synthetic acceleration (DSA) schemes has been observed with certain S N discretizations on two-dimensional Cartesian grids in the presence of material discontinuities. We will present more evidence supporting the conjecture that DSA effectiveness will degrade for multidimensional problems with discontinuous total cross sections, regardless of the particular physical configuration or spatial discretization. Fourier analysis and numerical experiments help us identify a set of representative problems for which established DSA schemes are ineffective, focusing on diffusive problems for which DSA is most needed. We consider a lumped, linear discontinuous spatial discretization of the S N transport equation on three-dimensional, unstructured tetrahedral meshes and look at a fully consistent and a 'partially consistent' DSA method for this discretization. The effectiveness of both methods is shown to degrade significantly. A Fourier analysis of the fully consistent DSA scheme in the limit of decreasing cell optical thickness supports the view that the DSA itself is failing when material discontinuities are present in a problem. We show that a Krylov iterative method, preconditioned with DSA, is an effective remedy that can be used to efficiently compute solutions for this class of problems. We show that as a preconditioner to the Krylov method, a partially consistent DSA method is more than adequate. In fact, it is preferable to a fully consistent method because the partially consistent method is based on a continuous finite element discretization of the diffusion equation that can be solved relatively easily. The Krylov method can be implemented in terms of the original S N source iteration coding with only slight modification. Results from numerical experiments show that replacing source iteration with a preconditioned Krylov method can efficiently solve problems that are virtually intractable with accelerated source iteration
Transport synthetic acceleration scheme for multi-dimensional neutron transport problems
Energy Technology Data Exchange (ETDEWEB)
Modak, R S; Kumar, Vinod; Menon, S V.G. [Theoretical Physics Div., Bhabha Atomic Research Centre, Mumbai (India); Gupta, Anurag [Reactor Physics Design Div., Bhabha Atomic Research Centre, Mumbai (India)
2005-09-15
The numerical solution of linear multi-energy-group neutron transport equation is required in several analyses in nuclear reactor physics and allied areas. Computer codes based on the discrete ordinates (Sn) method are commonly used for this purpose. These codes solve external source problem and K-eigenvalue problem. The overall solution technique involves solution of source problem in each energy group as intermediate procedures. Such a single-group source problem is solved by the so-called Source Iteration (SI) method. As is well-known, the SI-method converges very slowly for optically thick and highly scattering regions, leading to large CPU times. Over last three decades, many schemes have been tried to accelerate the SI; the most prominent being the Diffusion Synthetic Acceleration (DSA) scheme. The DSA scheme, however, often fails and is also rather difficult to implement. In view of this, in 1997, Ramone and others have developed a new acceleration scheme called Transport Synthetic Acceleration (TSA) which is much more robust and easy to implement. This scheme has been recently incorporated in 2-D and 3-D in-house codes at BARC. This report presents studies on the utility of TSA scheme for fairly general test problems involving many energy groups and anisotropic scattering. The scheme is found to be useful for problems in Cartesian as well as Cylindrical geometry. (author)
The boundary element method for the solution of the multidimensional inverse heat conduction problem
International Nuclear Information System (INIS)
Lagier, Guy-Laurent
1999-01-01
This work focuses on the solution of the inverse heat conduction problem (IHCP), which consists in the determination of boundary conditions from a given set of internal temperature measurements. This problem is difficult to solve due to its ill-posedness and high sensitivity to measurement error. As a consequence, numerical regularization procedures are required to solve this problem. However, most of these methods depend on the dimension and the nature, stationary or transient, of the problem. Furthermore, these methods introduce parameters, called hyper-parameters, which have to be chosen optimally, but can not be determined a priori. So, a new general method is proposed for solving the IHCP. This method is based on a Boundary Element Method formulation, and the use of the Singular Values Decomposition as a regularization procedure. Thanks to this method, it's possible to identify and eliminate the directions of the solution where the measurement error plays the major role. This algorithm is first validated on two-dimensional stationary and one-dimensional transient problems. Some criteria are presented in order to choose the hyper-parameters. Then, the methodology is applied to two-dimensional and three-dimensional, theoretical or experimental, problems. The results are compared with those obtained by a standard method and show the accuracy of the method, its generality, and the validity of the proposed criteria. (author) [fr
Transport synthetic acceleration scheme for multi-dimensional neutron transport problems
International Nuclear Information System (INIS)
Modak, R.S.; Vinod Kumar; Menon, S.V.G.; Gupta, Anurag
2005-09-01
The numerical solution of linear multi-energy-group neutron transport equation is required in several analyses in nuclear reactor physics and allied areas. Computer codes based on the discrete ordinates (Sn) method are commonly used for this purpose. These codes solve external source problem and K-eigenvalue problem. The overall solution technique involves solution of source problem in each energy group as intermediate procedures. Such a single-group source problem is solved by the so-called Source Iteration (SI) method. As is well-known, the SI-method converges very slowly for optically thick and highly scattering regions, leading to large CPU times. Over last three decades, many schemes have been tried to accelerate the SI; the most prominent being the Diffusion Synthetic Acceleration (DSA) scheme. The DSA scheme, however, often fails and is also rather difficult to implement. In view of this, in 1997, Ramone and others have developed a new acceleration scheme called Transport Synthetic Acceleration (TSA) which is much more robust and easy to implement. This scheme has been recently incorporated in 2-D and 3-D in-house codes at BARC. This report presents studies on the utility of TSA scheme for fairly general test problems involving many energy groups and anisotropic scattering. The scheme is found to be useful for problems in Cartesian as well as Cylindrical geometry. (author)
Directory of Open Access Journals (Sweden)
George Cristian Gruia
2013-05-01
Full Text Available In the aviation industry, propeller motor engines have a lifecycle of several thousand hours of flight and the maintenance is an important part of their lifecycle. The present article considers a multi-resource, priority-based case scheduling problem, which is applied in a Romanian manufacturing company, that repairs and maintains helicopter and airplane engines at a certain quality level imposed by the aviation standards. Given a reduced budget constraint, the management’s goal is to maximize the utilization of their resources (financial, material, space, workers, by maintaining a prior known priority rule. An Off-Line Dual Maximum Resource Bin Packing model, based on a Mixed Integer Programming model is thus presented. The obtained results show an increase with approx. 25% of the Just in Time shipping of the engines to the customers and approx. 12,5% increase in the utilization of the working area.
Directory of Open Access Journals (Sweden)
GEORGE CRISTIAN GRUIA
2013-05-01
Full Text Available In the aviation industry, propeller motor engines have a lifecycle of several thousand hours of flight and the maintenance is an important part of their lifecycle. The present article considers a multi-resource, priority-based case scheduling problem, which is applied in a Romanian manufacturing company, that repairs and maintains helicopter and airplane engines at a certain quality level imposed by the aviation standards. Given a reduced budget constraint, the management’s goal is to maximize the utilization of their resources (financial, material, space, workers, by maintaining a prior known priority rule. An Off-Line Dual Maximum Resource Bin Packing model, based on a Mixed Integer Programing model is thus presented. The obtained results show an increase with approx. 25% of the Just in Time shipping of the engines to the customers and approx. 12,5% increase in the utilization of the working area.
The Optimal Income Taxation of Couples as a Multi-Dimensional Screening Problem
DEFF Research Database (Denmark)
Kleven, Henrik Jacobsen; Kreiner, Claus Thustrup; Saez, Emmanuel
problem. We prove that, under regularity and separability assumptions for utility functions and for a wide class of social welfare functions, optimal tax schemes display negative jointness such that the tax rate on one person decreases in the earnings of the spouse. We also show that the tax...
Multidimensional phase change problems by the dual-reciprocity boundary-element method
International Nuclear Information System (INIS)
Jo, J.C.; Shin, W.K.; Choi, C.Y.
1999-01-01
Transient heat transfer problems with phase changes (Stefan problems) occur in many engineering situations, including potential core melting and solidification during pressurized-water-reactor severe accidents, ablation of thermal shields, melting and solidification of alloys, and many others. This article addresses the numerical analysis of nonlinear transient heat transfer with melting or solidification. An effective and simple procedure is presented for the simulation of the motion of the boundary and the transient temperature field during the phase change process. To accomplish this purpose, an iterative implicit solution algorithm has been developed by employing the dual-reciprocity boundary-element method. The dual-reciprocity boundary-element approach provided in this article is much simpler than the usual boundary-element method in applying a reciprocity principle and an available technique for dealing with the domain integral of the boundary element formulation simultaneously. In this article, attention is focused on two-dimensional melting (ablation)/solidification problems for simplicity. The accuracy and effectiveness of the present analysis method have been illustrated through comparisons of the calculation results of some examples of one-phase ablation/solidification problems with their known semianalytical or numerical solutions where available
Xu, Shuo; Ji, Ze; Truong Pham, Duc; Yu, Fan
2011-11-01
The simultaneous mission assignment and home allocation for hospital service robots studied is a Multidimensional Assignment Problem (MAP) with multiobjectives and multiconstraints. A population-based metaheuristic, the Binary Bees Algorithm (BBA), is proposed to optimize this NP-hard problem. Inspired by the foraging mechanism of honeybees, the BBA's most important feature is an explicit functional partitioning between global search and local search for exploration and exploitation, respectively. Its key parts consist of adaptive global search, three-step elitism selection (constraint handling, non-dominated solutions selection, and diversity preservation), and elites-centred local search within a Hamming neighbourhood. Two comparative experiments were conducted to investigate its single objective optimization, optimization effectiveness (indexed by the S-metric and C-metric) and optimization efficiency (indexed by computational burden and CPU time) in detail. The BBA outperformed its competitors in almost all the quantitative indices. Hence, the above overall scheme, and particularly the searching history-adapted global search strategy was validated.
International Nuclear Information System (INIS)
Kim, M.G.
1980-01-01
The multigroup neutron diffusion equations with the constraint of specified power distributions are investigated by the application of the straight-line method which can be considered as the limiting case of zero mesh space in the finite difference method. The standard partial differential form of the diffusion equation is reduced to sets of ordinary differential equations and then converted into sets of integral equations by using Green's functions defined on the pseudo straight lines. Coupling of each straight line to the adjacent lines arises from the application of a three-point central difference formula. The interfaces encountered between two regions are taken into account by imposing the continuity conditions for the grown fluxes and net currents with Taylor expansions of internal fluxes at the interface positions. A few sample problems are selected to test the validity of the method. It is found that the proposed method of solution is similar to the finite Fourier sine transform. Numerical results for the solutions obtained by the method of straight lines are compared with the results of the exact analytical solutions for simple geometries. These comparisons indicate that the proposed method is compatible with the analytical method, and in some problems considered the straight-line solutions are much more efficient than the exact solutions. The method is also extended to the reactor kinetics problem by expressing the kinetics parameters in terms of the basis functions which are used to obtain the solutions of the steady-state neutron diffusion equations
Zanni, Martin Thomas; Damrauer, Niels H.
2010-07-20
A multidimensional spectrometer for the infrared, visible, and ultraviolet regions of the electromagnetic spectrum, and a method for making multidimensional spectroscopic measurements in the infrared, visible, and ultraviolet regions of the electromagnetic spectrum. The multidimensional spectrometer facilitates measurements of inter- and intra-molecular interactions.
Use of endochronic plasticity for multi-dimensional small and large strain problems
International Nuclear Information System (INIS)
Hsieh, B.J.
1980-04-01
The endochronic plasticity theory was proposed in its general form by K.C. Valanis. An intrinsic time measure, which is a property of the material, is used in the theory. the explicit forms of the constitutive equation resemble closely those of the classical theory of linear viscoelasticity. Excellent agreement between the predicted and experimental results is obtained for some metallic and non-metallic materials for one dimensional cases. No reference on the use of endochronic plasticity consistent with the general theory proposed by Valanis is available in the open literature. In this report, the explicit constitutive equations are derived that are consistent with the general theory for one-dimensional (simple tension or compression), two-dimensional plane strain or stress and three-dimensional axisymmetric problems
Energy Technology Data Exchange (ETDEWEB)
Xu, Z., E-mail: zhanjie.xu@kit.ed [Forschungszentrum Karlsruhe, P.O. Box 3640, 76021 Karlsruhe (Germany); Travis, J.R. [Ingenieurbuero DuBois-Pitzer-Travis, 63071 Offenbach (Germany); Breitung, W.; Jordan, T. [Forschungszentrum Karlsruhe, P.O. Box 3640, 76021 Karlsruhe (Germany)
2010-12-15
Potentially explosive dust aerosol mobilization in the vacuum vessel is an important safety issue of the ITER facility, especially in scenarios of loss of vacuum accidents. Therefore dust mobilization modeling is ongoing in Research Center Karlsuhe. At first the aerosol particle model in the GASFLOW computer code is introduced briefly. To verify the particle model, a series of particle diffusion problems are simulated in one-, two- and three-dimensions. In each problem a particle source is initially exposed to an advective gas flow. Then a dust cloud is formed in the down stream. To obtain the theoretical solution about the particle concentration in the dust cloud, the governing diffusion partial differential equations with an additional advection term are solved by using Green's function method. Different spatial and temporal characters about the particle sources are also considered, e.g., instantaneous or continuous sources, line, or volume sources and so forth. The GASFLOW simulation results about the particle concentrations and the corresponding Green's function solutions are compared case by case. Very good agreements are found between the theoretical solutions and the GASGLOW simulations, when the drag force between the micron-sized particles and the conveying gas flow meets the Stokes' law about resistance. This situation is corresponding to a very small Reynolds number based on the particle diameter, with a negligible inertia effect of the particles. This verification work shows that the particle model of the GASFLOW code can reproduce numerically particle transport and diffusion in a good way.
van der Pol, T.M.; Hoeve, M.; Noom, M.J.; Stams, G.J.J.M.; Doreleijers, T.A.H.; van Domburgh, L.; Vermeiren, R.R.J.M.
Background: Multidimensional family therapy (MDFT) is a well-established treatment for adolescents showing both substance abuse and/or antisocial behavior. Method: The effectiveness of MDFT in reducing adolescents’ substance abuse, delinquency, externalizing and internalizing psychopathology, and
Soloveichik, Yury G.; Persova, Marina G.; Domnikov, Petr A.; Koshkina, Yulia I.; Vagin, Denis V.
2018-03-01
We propose an approach to solving multisource induction logging problems in multidimensional media. According to the type of induction logging tools, the measurements are performed in the frequency range of 10 kHz to 14 MHz, transmitter-receiver offsets vary in the range of 0.5-8 m or more, and the trajectory length is up to 1 km. For calculating the total field, the primary-secondary field approach is used. The secondary field is calculated with the use of the finite-element method (FEM), irregular non-conforming meshes with local refinements and a direct solver. The approach to constructing basis functions with the continuous tangential components (from Hcurl(Ω)) on the non-conforming meshes from the standard shape vector functions is developed. On the basis of this method, the algorithm of generating global matrices and a vector of the finite-element equation system is proposed. We also propose the method of grouping the logging tool positions, which makes it possible to significantly increase the computational effectiveness. This is achieved due to the compromise between the possibility of using the 1-D background medium, which is very similar to the investigated multidimensional medium for a small group, and the decrease in the number of the finite-element matrix factorizations with the increasing number of tool positions in one group. For calculating the primary field, we propose the method based on the use of FEM. This method is highly effective when the 1-D field is required to be calculated at a great number of points. The use of this method significantly increases the effectiveness of the primary-secondary field approach. The proposed approach makes it possible to perform modelling both in the 2.5-D case (i.e. without taking into account a borehole and/or invasion zone effect) and the 3-D case (i.e. for models with a borehole and invasion zone). The accuracy of numerical results obtained with the use of the proposed approach is compared with the one
Optimized packings with applications
Pintér, János
2015-01-01
This volume presents a selection of case studies that address a substantial range of optimized object packings (OOP) and their applications. The contributing authors are well-recognized researchers and practitioners. The mathematical modelling and numerical solution aspects of each application case study are presented in sufficient detail. A broad range of OOP problems are discussed: these include various specific and non-standard container loading and object packing problems, as well as the stowing of hazardous and other materials on container ships, data centre resource management, automotive engineering design, space station logistic support, cutting and packing problems with placement constraints, the optimal design of LED street lighting, robust sensor deployment strategies, spatial scheduling problems, and graph coloring models and metaheuristics for packing applications. Novel points of view related to model development and to computational nonlinear, global, mixed integer optimization and heuristic st...
International Nuclear Information System (INIS)
Bae, B. U.; Park, Y. S.; Kim, J. R.; Kang, K. H.; Choi, K. Y.; Sung, H. J.; Hwang, M. J.; Kang, D. H.; Lim, S. G.; Jun, S. S.
2015-01-01
Participants of DSP-03 were divided in three groups and each group has focused on the specific subject related to the enhancement of the code analysis. The group A tried to investigate scaling capability of ATLAS test data by comparing to the code analysis for a prototype, and the group C studied to investigate effect of various models in the one-dimensional codes. This paper briefly summarizes the code analysis result from the group B participants in the DSP-03 of the ATLAS test facility. The code analysis by Group B focuses highly on investigating the multi-dimensional thermal hydraulic phenomena in the ATLAS facility during the SLB transient. Even though the one-dimensional system analysis code cannot simulate the whole system of the ATLAS facility with a nodalization of the CFD (Computational Fluid Dynamics) scale, a reactor pressure vessel can be considered with multi-dimensional components to reflect the thermal mixing phenomena inside a downcomer and a core. Also, the CFD could give useful information for understanding complex phenomena in specific components such as the reactor pressure vessel. From the analysis activity of Group B in ATLAS DSP-03, participants adopted a multi-dimensional approach to the code analysis for the SLB transient in the ATLAS test facility. The main purpose of the analysis was to investigate prediction capability of multi-dimensional analysis tools for the SLB experiment result. In particular, the asymmetric cooling and thermal mixing phenomena in the reactor pressure vessel could be significantly focused for modeling the multi-dimensional components
Hardness of approximation for strip packing
DEFF Research Database (Denmark)
Adamaszek, Anna Maria; Kociumaka, Tomasz; Pilipczuk, Marcin
2017-01-01
Strip packing is a classical packing problem, where the goal is to pack a set of rectangular objects into a strip of a given width, while minimizing the total height of the packing. The problem has multiple applications, for example, in scheduling and stock-cutting, and has been studied extensively......)-approximation by two independent research groups [FSTTCS 2016,WALCOM 2017]. This raises a questionwhether strip packing with polynomially bounded input data admits a quasi-polynomial time approximation scheme, as is the case for related twodimensional packing problems like maximum independent set of rectangles or two...
Institute of Scientific and Technical Information of China (English)
Rui ZHAO; Gui-he QIN; Jia-qiao LIU
2016-01-01
As FlexRay communication protocol is extensively used in distributed real-time applications on vehicles, signal scheduling in FlexRay network becomes a critical issue to ensure the safe and efficient operation of time-critical applications. In this study, we propose a rectangle bin packing optimization approach to schedule communication signals with timing constraints into the FlexRay static segment at minimum bandwidth cost. The proposed approach, which is based on integer linear program-ming (ILP), supports both the slot assignment mechanisms provided by the latest version of the FlexRay specification, namely, the single sender slot multiplexing, and multiple sender slot multiplexing mechanisms. Extensive experiments on a synthetic and an automotive X-by-wire system case study demonstrate that the proposed approach has a well optimized performance.
P.A.N. Bosman (Peter); Gallagher, M. (Marcus)
2016-01-01
textabstractWe consider a scalable problem that has strong ties with real-world problems, can be compactly formulated and efficiently evaluated, yet is not trivial to solve and has interesting characteristics that differ from most commonly used benchmark problems: packing n circles in a square
Centers for Disease Control (CDC) Podcasts
2011-08-16
In this podcast for kids, the Kidtastics talk about how to pack a lunch safely, to help keep you from getting sick. Created: 8/16/2011 by National Center for Emerging and Zoonotic Infectious Diseases (NCEZID). Date Released: 8/16/2011.
Centers for Disease Control (CDC) Podcasts
2011-08-22
In this podcast for kids, the Kidtastics talk about packing a lunch that's not boring and is full of the power and energy kids need to make it through the day. Created: 8/22/2011 by National Center for Emerging and Zoonotic Infectious Diseases (NCEZID). Date Released: 8/22/2011.
Optimal Packed String Matching
DEFF Research Database (Denmark)
Ben-Kiki, Oren; Bille, Philip; Breslauer, Dany
2011-01-01
In the packed string matching problem, each machine word accommodates – characters, thus an n-character text occupies n/– memory words. We extend the Crochemore-Perrin constantspace O(n)-time string matching algorithm to run in optimal O(n/–) time and even in real-time, achieving a factor – speed...
Hickendorff, Marian
2013-01-01
The results of an exploratory study into measurement of elementary mathematics ability are presented. The focus is on the abilities involved in solving standard computation problems on the one hand and problems presented in a realistic context on the other. The objectives were to assess to what extent these abilities are shared or distinct, and…
Multidimensional nonlinear descriptive analysis
Nishisato, Shizuhiko
2006-01-01
Quantification of categorical, or non-numerical, data is a problem that scientists face across a wide range of disciplines. Exploring data analysis in various areas of research, such as the social sciences and biology, Multidimensional Nonlinear Descriptive Analysis presents methods for analyzing categorical data that are not necessarily sampled randomly from a normal population and often involve nonlinear relations. This reference not only provides an overview of multidimensional nonlinear descriptive analysis (MUNDA) of discrete data, it also offers new results in a variety of fields. The first part of the book covers conceptual and technical preliminaries needed to understand the data analysis in subsequent chapters. The next two parts contain applications of MUNDA to diverse data types, with each chapter devoted to one type of categorical data, a brief historical comment, and basic skills peculiar to the data types. The final part examines several problems and then concludes with suggestions for futu...
International Nuclear Information System (INIS)
Toumi, I.
1990-04-01
This thesis is devoted to the study of the Riemann problem and the construction of Godunov type numerical schemes for one or two dimensional two-phase flow models. In the first part, we study the Riemann problem for the well-known Drift-Flux, model which has been widely used for the analysis of thermal hydraulics transients. Then we use this study to construct approximate Riemann solvers and we describe the corresponding Godunov type schemes for simplified equation of state. For computation of complex two-phase flows, a weak formulation of Roe's approximate Riemann solver, which gives a method to construct a Roe-averaged jacobian matrix with a general equation of state, is proposed. For two-dimensional flows, the developed methods are based upon an approximate solver for a two-dimensional Riemann problem, according to Harten-Lax-Van Leer principles. The numerical results for standard test problems show the good behaviour of these numerical schemes for a wide range of flow conditions [fr
Deterministic indexing for packed strings
DEFF Research Database (Denmark)
Bille, Philip; Gørtz, Inge Li; Skjoldjensen, Frederik Rye
2017-01-01
Given a string S of length n, the classic string indexing problem is to preprocess S into a compact data structure that supports efficient subsequent pattern queries. In the deterministic variant the goal is to solve the string indexing problem without any randomization (at preprocessing time...... or query time). In the packed variant the strings are stored with several character in a single word, giving us the opportunity to read multiple characters simultaneously. Our main result is a new string index in the deterministic and packed setting. Given a packed string S of length n over an alphabet σ...
Directory of Open Access Journals (Sweden)
Alexis Cedeño Trujillo
2006-04-01
Full Text Available
Data Warehousing, es una tecnología para el almacenamiento de grandes volúmenes de datos en una amplia perspectiva de tiempo para el soporte a la toma de decisiones. Debido a su orientación analítica, impone un procesamiento distinto al de los sistemas operacionales y requiere de un diseño de base de datos más cercano a la visión de los usuarios finales, permitiendo que sea más fácil la recuperación de información y la navegación. Este diseño de base de datos se conoce como modelo multidimensional, este artículo, abordará sus características principales.
International Nuclear Information System (INIS)
Lopez, C.; Koski, J.A.; Razani, A.
2000-01-01
A study of the errors introduced when one-dimensional inverse heat conduction techniques are applied to problems involving two-dimensional heat transfer effects was performed. The geometry used for the study was a cylinder with similar dimensions as a typical container used for the transportation of radioactive materials. The finite element analysis code MSC P/Thermal was used to generate synthetic test data that was then used as input for an inverse heat conduction code. Four different problems were considered including one with uniform flux around the outer surface of the cylinder and three with non-uniform flux applied over 360 deg C, 180 deg C, and 90 deg C sections of the outer surface of the cylinder. The Sandia One-Dimensional Direct and Inverse Thermal (SODDIT) code was used to estimate the surface heat flux of all four cases. The error analysis was performed by comparing the results from SODDIT and the heat flux calculated based on the temperature results obtained from P/Thermal. Results showed an increase in error of the surface heat flux estimates as the applied heat became more localized. For the uniform case, SODDIT provided heat flux estimates with a maximum error of 0.5% whereas for the non-uniform cases, the maximum errors were found to be about 3%, 7%, and 18% for the 360 deg C, 180 deg C, and 90 deg C cases, respectively
The pursuit of perfect packing
Weaire, Denis
2008-01-01
Coauthored by one of the creators of the most efficient space packing solution, the Weaire-Phelan structure, The Pursuit of Perfect Packing, Second Edition explores a problem of importance in physics, mathematics, chemistry, biology, and engineering: the packing of structures. Maintaining its mathematical core, this edition continues and revises some of the stories from its predecessor while adding several new examples and applications. The book focuses on both scientific and everyday problems ranging from atoms to honeycombs. It describes packing models, such as the Kepler conjecture, Voronoï decomposition, and Delaunay decomposition, as well as actual structure models, such as the Kelvin cell and the Weaire-Phelan structure. The authors discuss numerous historical aspects and provide biographical details on influential contributors to the field, including emails from Thomas Hales and Ken Brakke. With examples from physics, crystallography, engineering, and biology, this accessible and whimsical bo...
The pursuit of perfect packing
Weaire, Denis
2000-01-01
In 1998 Thomas Hales dramatically announced the solution of a problem that has long teased eminent mathematicians: what is the densest possible arrangement of identical spheres? The Pursuit of Perfect Packing recounts the story of this problem and many others that have to do with packing things together. The examples are taken from mathematics, physics, biology, and engineering, including the arrangement of soap bubbles in foam, atoms in a crystal, the architecture of the bee''s honeycomb, and the structure of the Giant''s Causeway. Using an informal style and with key references, the book also includes brief accounts of the lives of many of the scientists who devoted themselves to problems of packing over many centuries, together with wry comments on their efforts. It is an entertaining introduction to the field for both specialists and the more general public.
Multidimensional Heat Conduction
DEFF Research Database (Denmark)
Rode, Carsten
1998-01-01
Analytical theory of multidimensional heat conduction. General heat conduction equation in three dimensions. Steay state, analytical solutions. The Laplace equation. Method of separation of variables. Principle of superposition. Shape factors. Transient, multidimensional heat conduction....
Energy Technology Data Exchange (ETDEWEB)
Singleton, Robert Jr. [Los Alamos National Laboratory; Israel, Daniel M. [Los Alamos National Laboratory; Doebling, Scott William [Los Alamos National Laboratory; Woods, Charles Nathan [Los Alamos National Laboratory; Kaul, Ann [Los Alamos National Laboratory; Walter, John William Jr [Los Alamos National Laboratory; Rogers, Michael Lloyd [Los Alamos National Laboratory
2016-05-09
For code verification, one compares the code output against known exact solutions. There are many standard test problems used in this capacity, such as the Noh and Sedov problems. ExactPack is a utility that integrates many of these exact solution codes into a common API (application program interface), and can be used as a stand-alone code or as a python package. ExactPack consists of python driver scripts that access a library of exact solutions written in Fortran or Python. The spatial profiles of the relevant physical quantities, such as the density, fluid velocity, sound speed, or internal energy, are returned at a time specified by the user. The solution profiles can be viewed and examined by a command line interface or a graphical user interface, and a number of analysis tools and unit tests are also provided. We have documented the physics of each problem in the solution library, and provided complete documentation on how to extend the library to include additional exact solutions. ExactPack’s code architecture makes it easy to extend the solution-code library to include additional exact solutions in a robust, reliable, and maintainable manner.
Multidimensional sexual perfectionism.
Stoeber, Joachim; Harvey, Laura N; Almeida, Isabel; Lyons, Emma
2013-11-01
Perfectionism is a multidimensional personality characteristic that can affect all areas of life. This article presents the first systematic investigation of multidimensional perfectionism in the domain of sexuality exploring the unique relationships that different forms of sexual perfectionism show with positive and negative aspects of sexuality. A sample of 272 university students (52 male, 220 female) completed measures of four forms of sexual perfectionism: self-oriented, partner-oriented, partner-prescribed, and socially prescribed. In addition, they completed measures of sexual esteem, sexual self-efficacy, sexual optimism, sex life satisfaction (capturing positive aspects of sexuality) and sexual problem self-blame, sexual anxiety, sexual depression, and negative sexual perfectionism cognitions during sex (capturing negative aspects). Results showed unique patterns of relationships for the four forms of sexual perfectionism, suggesting that partner-prescribed and socially prescribed sexual perfectionism are maladaptive forms of sexual perfectionism associated with negative aspects of sexuality whereas self-oriented and partner-oriented sexual perfectionism emerged as ambivalent forms associated with positive and negative aspects.
Ng, Albert H.
2011-01-24
To incorporate protein polarization effects within a protein combinatorial optimization framework, we decompose the polarizable force field AMOEBA into low order terms. Including terms up to the third-order provides a fair approximation to the full energy while maintaining tractability. We represent the polarizable packing problem for protein G as a hypergraph and solve for optimal rotamers with the FASTER combinatorial optimization algorithm. These approximate energy models can be improved to high accuracy [root mean square deviation (rmsd) < 1 kJ mol -1] via ridge regression. The resulting trained approximations are used to efficiently identify new, low-energy solutions. The approach is general and should allow combinatorial optimization of other many-body problems. © 2011 Wiley Periodicals, Inc. J Comput Chem, 2011 Copyright © 2011 Wiley Periodicals, Inc.
Domain Discretization and Circle Packings
DEFF Research Database (Denmark)
Dias, Kealey
A circle packing is a configuration of circles which are tangent with one another in a prescribed pattern determined by a combinatorial triangulation, where the configuration fills a planar domain or a two-dimensional surface. The vertices in the triangulation correspond to centers of circles...... to domain discretization problems such as triangulation and unstructured mesh generation techniques. We wish to ask ourselves the question: given a cloud of points in the plane (we restrict ourselves to planar domains), is it possible to construct a circle packing preserving the positions of the vertices...... and constrained meshes having predefined vertices as constraints. A standard method of two-dimensional mesh generation involves conformal mapping of the surface or domain to standardized shapes, such as a disk. Since circle packing is a new technique for constructing discrete conformal mappings, it is possible...
The advantages of hydraulic packing extraction
International Nuclear Information System (INIS)
Baker, R.S.
1991-01-01
Today's competitive environment, coupled with industry's desire to improve the efficiency of plant maintenance and operations, has management continually seeking ways to save time, money, and, at nuclear plants, radiation exposure. One area where a tremendous improvement in efficiency can be realized is valve packing removal. For example, industry experience indicates that up to 70% of the time it takes to repack a valve can be spent just removing the old packing. In some case, the bonnets of small valves are removed to facilitate packing removal and prevent stem and stuffing box damage that can occur when using packing removal picks. In other cases, small valves are simply removed and discarded because it costs less to replace the valves than to remove the packing using conventional methods. Hydraulic packing extraction greatly reduces packing removal time and will not damage the stem nor stuffing box, thus eliminating the need for bonnet removal or valve replacement. This paper will review some of the more common problems associated with manual packing extraction techniques. It will explain how hydraulic packing extraction eliminates or greatly reduces the impact of each of the problem areas. A discussion will be provided of some actual industry operating experiences related to success stories using hydraulic packing extraction. The paper will also briefly describe the operating parameters associated with hydraulic packing extraction tools. Throughout the paper, actual operating experiences from the nuclear power, fossil power, petrochemical, and refinery industries will be used to support the conclusion that hydraulic packing extraction is an alternative that can save time, money, and exposure
Modi ed strip packing heuristics for the rectangular variable-sized ...
African Journals Online (AJOL)
Two packing problems are considered in this paper, namely the well-known strip packing problem (SPP) and the variable-sized bin packing problem (VSBPP). A total of 252 strip packing heuristics (and variations thereof) from the literature, as well as novel heuristics proposed by the authors, are compared statistically by ...
Directory of Open Access Journals (Sweden)
Mihaela MUNTEAN
2006-01-01
Full Text Available Using SQL you can manipulate multidimensional data and extract that data into a relational table. There are many PL/SQL packages that you can use directly in SQL*Plus or indirectly in Analytic Workspace Manager and OLAP Worksheet. In this article I discussed about some methods that you can use for manipulating and extracting multidimensional data.
Multidimensional high harmonic spectroscopy
International Nuclear Information System (INIS)
Bruner, Barry D; Soifer, Hadas; Shafir, Dror; Dudovich, Nirit; Serbinenko, Valeria; Smirnova, Olga
2015-01-01
High harmonic generation (HHG) has opened up a new frontier in ultrafast science where attosecond time resolution and Angstrom spatial resolution are accessible in a single measurement. However, reconstructing the dynamics under study is limited by the multiple degrees of freedom involved in strong field interactions. In this paper we describe a new class of measurement schemes for resolving attosecond dynamics, integrating perturbative nonlinear optics with strong-field physics. These approaches serve as a basis for multidimensional high harmonic spectroscopy. Specifically, we show that multidimensional high harmonic spectroscopy can measure tunnel ionization dynamics with high precision, and resolves the interference between multiple ionization channels. In addition, we show how multidimensional HHG can function as a type of lock-in amplifier measurement. Similar to multi-dimensional approaches in nonlinear optical spectroscopy that have resolved correlated femtosecond dynamics, multi-dimensional high harmonic spectroscopy reveals the underlying complex dynamics behind attosecond scale phenomena. (paper)
Does Post Septoplasty Nasal Packing Reduce Complications?
Directory of Open Access Journals (Sweden)
Bijan Naghibzadeh
2011-01-01
Full Text Available The main issues in nasal surgery are to stabilize the nose in the good position after surgery and preserve the cartilages and bones in the favorable situation and reduce the risk of deviation recurrence. Also it is necessary to avoid the synechia formation, nasal valve narrowing, hematoma and bleeding. Due to the above mentioned problems and in order to solve and minimize them nasal packing, nasal splint and nasal mold have been advised. Patients for whom the nasal packing used may faced to some problems like naso-pulmonary reflex, intractable pain, sleep disorder, post operation infection and very dangerous complication like toxic shock syndrome. We have two groups of patients and three surgeons (one of the surgeons used post operative nasal packing in his patients and the two others surgeons did not.Complications and morbidities were compared in these two groups. Comparing the two groups showed that the rate of complication and morbidities between these two groups were same and the differences were not valuable, except the pain and discomfort post operatively and at the time of its removal. Nasal packing has several risks for the patients while its effects are not studied. Septoplasty can be safely performed without postoperative nasal packing. Nasal packing had no main findings that compensated its usage. Septal suture is one of the procedures that can be used as alternative method to nasal packing. Therefore the nasal packing after septoplasty should be reserved for the patients with increased risk of bleeding.
Energy Technology Data Exchange (ETDEWEB)
Jung, B. D.; Jung, J. J.; Ha, K. S.; Hwang, M. K.; Lee, Y. S.; Lee, W. J. [KAERI, Taejon (Korea, Republic of)
1999-10-01
The readability of MARS code has been enhanced greatly by replacing the bit-packed word with several logical words and integer words and recoding the related subroutines, which have the complicated bit operations and packed words. Functional improvements of code has been achieved through the multiple uses of dynamic link libraries(DLL) for containment analysis module CONTEMPT4 and multidimensional kinetics analysis module MASTER. The establishment of integrated analysis system, MARS/CONTEMPT/MASTER, was validated through the verification calculation for a postulated problem. MARS user-friendly features are also improved by displaying the 2D contour map of 3 D module data on-line. In addition to the on-line-graphics, the MARS windows menus were upgraded to include the on-line-manual, pre-view of input and output, and link to MARS web site. As a result, the readability, applicability, and user-friendly features of MARS code has been greatly enhanced.
International Nuclear Information System (INIS)
Jung, B. D.; Jung, J. J.; Ha, K. S.; Hwang, M. K.; Lee, Y. S.; Lee, W. J.
1999-01-01
The readability of MARS code has been enhanced greatly by replacing the bit-packed word with several logical words and integer words and recoding the related subroutines, which have the complicated bit operations and packed words. Functional improvements of code has been achieved through the multiple uses of dynamic link libraries(DLL) for containment analysis module CONTEMPT4 and multidimensional kinetics analysis module MASTER. The establishment of integrated analysis system, MARS/CONTEMPT/MASTER, was validated through the verification calculation for a postulated problem. MARS user-friendly features are also improved by displaying the 2D contour map of 3 D module data on-line. In addition to the on-line-graphics, the MARS windows menus were upgraded to include the on-line-manual, pre-view of input and output, and link to MARS web site. As a result, the readability, applicability, and user-friendly features of MARS code has been greatly enhanced
Valve-stem-packing improvement study. Final report
International Nuclear Information System (INIS)
Adey, C.W.; Klein, J.J.
1982-08-01
By employing questionnaires and face-to-face interviews with valve and valve packing manufacturers, as well as nuclear plant personnel, an understanding of valve stem packing leakage problems from each of the three viewpoints was developed. This information, in-house experience, and available technical literature were used to develop specific recommendations for valve manufacturers, valve packing manufacturers, and nuclear plant valve users. It was generally recommended that each these groups make better use of graphite packing. The questionnaires and interviews indicated that increased usage of graphite packing over the last few years has reduced the incidence of valve packing problems. To confirm this, a survey of Licensee Event Reports (LERs) from 1972 to 1980 was undertaken using the keywords Valve and Packing. A statistical analysis of the LER data confirms that the adoption of graphite packing has significantly reduced valve stem leakage
International Nuclear Information System (INIS)
Lumay, G; Vandewalle, N
2007-01-01
We present an experimental protocol that allows one to tune the packing fraction η of a random pile of ferromagnetic spheres from a value close to the lower limit of random loose packing η RLP ≅0.56 to the upper limit of random close packing η RCP ≅0.64. This broad range of packing fraction values is obtained under normal gravity in air, by adjusting a magnetic cohesion between the grains during the formation of the pile. Attractive and repulsive magnetic interactions are found to affect stongly the internal structure and the stability of sphere packing. After the formation of the pile, the induced cohesion is decreased continuously along a linear decreasing ramp. The controlled collapse of the pile is found to generate various and reproducible values of the random packing fraction η
Fast Searching in Packed Strings
DEFF Research Database (Denmark)
Bille, Philip
2009-01-01
Given strings P and Q the (exact) string matching problem is to find all positions of substrings in Q matching P. The classical Knuth-Morris-Pratt algorithm [SIAM J. Comput., 1977] solves the string matching problem in linear time which is optimal if we can only read one character at the time....... However, most strings are stored in a computer in a packed representation with several characters in a single word, giving us the opportunity to read multiple characters simultaneously. In this paper we study the worst-case complexity of string matching on strings given in packed representation. Let m...... word-RAM with logarithmic word size we present an algorithm using time O(n/log(sigma) n + m + occ) Here occ is the number of occurrences of P in Q. For m = o(n) this improves the O(n) bound...
Structure of multidimensional patterns
International Nuclear Information System (INIS)
Smith, S.P.
1982-01-01
The problem of describing the structure of multidimensional data is important in exploratory data analysis, statistical pattern recognition, and image processing. A data set is viewed as a collection of points embedded in a high dimensional space. The primary goal of this research is to determine if the data have any clustering structure; such a structure implies the presence of class information (categories) in the data. A statistical hypothesis is used in the decision making. To this end, data with no structure are defined as data following the uniform distribution over some compact convex set in K-dimensional space, called the sampling window. This thesis defines two new tests for uniformity along with various sampling window estimators. The first test is a volume-based test which captures density changes in the data. The second test compares a uniformly distributed sample to the data by using the minimal spanning tree (MST) of the polled samples. Sampling window estimators are provided for simple sampling windows and use the convex hull of the data as a general sampling window estimator. For both of the tests for uniformity, theoretical results are provided on their size, and study their size and power against clustered alternatives is studied. Simulation is also used to study the efficacy of the sampling window estimators
Development of an effective valve packing program
Energy Technology Data Exchange (ETDEWEB)
Hart, K.A.
1996-12-01
Current data now shows that graphite valve packing installed within the guidance of a controlled program produces not only reliable stem sealing but predictable running loads. By utilizing recent technological developments in valve performance monitoring for both MOV`s and AOV`s, valve packing performance can be enhanced while reducing maintenance costs. Once known, values are established for acceptable valve packing loads, the measurement of actual valve running loads via the current MOV/AOV diagnostic techniques can provide indication of future valve stem sealing problems, improper valve packing installation or identify the opportunity for valve packing program improvements. At times the full benefit of these advances in material and predictive technology remain under utilized due to simple past misconceptions associated with valve packing. This paper will explore the basis for these misconceptions, provide general insight into the current understanding of valve packing and demonstrate how with this new understanding and current valve diagnostic equipment the key aspects required to develop an effective, quality valve packing program fit together. The cost and operational benefits provided by this approach can be significant impact by the: elimination of periodic valve repacking, reduction of maintenance costs, benefits of leak-free valve operation, justification for reduced Post Maintenance Test Requirements, reduced radiation exposure, improved plant appearance.
Packing Degenerate Graphs Greedily
Czech Academy of Sciences Publication Activity Database
Allen, P.; Böttcher, J.; Hladký, J.; Piguet, Diana
2017-01-01
Roč. 61, August (2017), s. 45-51 ISSN 1571-0653 R&D Projects: GA ČR GJ16-07822Y Institutional support: RVO:67985807 Keywords : tree packing conjecture * graph packing * graph processes Subject RIV: BA - General Mathematics OBOR OECD: Pure mathematics
Packing force data correlations
International Nuclear Information System (INIS)
Heiman, S.M.
1994-01-01
One of the issues facing valve maintenance personnel today deals with an appropriate methodology for installing and setting valve packing that will minimize leak rates, yet ensure functionality of the the valve under all anticipated operating conditions. Several variables can affect a valve packing's ability to seal, such as packing bolt torque, stem finish, and lubrication. Stem frictional force can be an excellent overall indicator of some of the underlying conditions that affect the sealing characteristics of the packing and the best parameter to use when adjusting the packing. This paper addresses stem friction forces, analytically derives the equations related to these forces, presents a methodology for measuring these forces on valve stems, and attempts to correlate the data directly to the underlying variables
Packing configuration performance for small stem diameters
International Nuclear Information System (INIS)
Aikin, J.A.; Spence, C.G.; Cumming, D.
1997-01-01
The extensive use of graphite packing and its excellent track record for large isolating valves in CANDU, Primary Heat Transfer (PHT) systems has resulted in an increased application of graphite packing on the conventional side. Many of these applications are in air operated valves (AOVs) where the packing sets are used on small stem diameters (<1 inch) with frequent short-cycling strokes (± 10% of full stroke). The direct application of the proven packing configurations for large isolated valves to control valve application has generated problems such as stiction, packing wear and, in isolated cases, stem stall. To address this issue, a test program was conducted at AECL, CRL by MED branch. The testing showed that by reconfiguring the packing sets and using PTFE wafers reductions in stem friction of 50% at ambient conditions, a 3 fold at hot conditions are achievable. The test program also demonstrated benefits gained in packing wear with different stem roughness finishes and the potential need to exercise small stems valves that see less than full stroke cycling. The paper describes the tests results and provides field support experience. (author)
Pottmann, Helmut; Jiang, Caigui; Hö binger, Mathias; Wang, Jun; Bompas, Philippe; Wallner, Johannes
2015-01-01
optimization schemes for the computation of quad-based support structures. Hex-dominant structures may be designed via Voronoi tessellations, power diagrams, sphere packings and various extensions of these concepts. Apart from the obvious application as load
Garriga Torrecillas, Núria; Otrubova, Natalie; Worm, Robert; Larroque, Thibaut
2017-01-01
6-Pack crisps are one of the main products sold by PepsiCo using the standard shelf storage options offered by Tesco PLC. While presenting specific packaging involves a multitude of variables. This report focusses on cognitive recognition, brand confusion and product attractiveness. PepsiCo asked the research team to investigate innovative ways of presenting the crisp 6-pack variant on instore displays. research shows that attraction is crucial in the form of expected rewards. The combination...
Applied multidimensional systems theory
Bose, Nirmal K
2017-01-01
Revised and updated, this concise new edition of the pioneering book on multidimensional signal processing is ideal for a new generation of students. Multidimensional systems or m-D systems are the necessary mathematical background for modern digital image processing with applications in biomedicine, X-ray technology and satellite communications. Serving as a firm basis for graduate engineering students and researchers seeking applications in mathematical theories, this edition eschews detailed mathematical theory not useful to students. Presentation of the theory has been revised to make it more readable for students, and introduce some new topics that are emerging as multidimensional DSP topics in the interdisciplinary fields of image processing. New topics include Groebner bases, wavelets, and filter banks.
Javidi, Bahram; Andres, Pedro
2014-01-01
Provides a broad overview of advanced multidimensional imaging systems with contributions from leading researchers in the field Multi-dimensional Imaging takes the reader from the introductory concepts through to the latest applications of these techniques. Split into 3 parts covering 3D image capture, processing, visualization and display, using 1) a Multi-View Approach and 2.) a Holographic Approach, followed by a 3rd part addressing other 3D systems approaches, applications and signal processing for advanced 3D imaging. This book describes recent developments, as well as the prospects and
Bidispersed Sphere Packing on Spherical Surfaces
Atherton, Timothy; Mascioli, Andrew; Burke, Christopher
Packing problems on spherical surfaces have a long history, originating in the classic Thompson problem of finding the ground state configuration of charges on a sphere. Such packings contain a minimal number of defects needed to accommodate the curvature; this is predictable using the Gauss-Bonnet theorem from knowledge of the topology of the surface and the local symmetry of the ordering. Famously, the packing of spherical particles on a sphere contains a 'scar' transition, where additional defects over those required by topology appear above a certain critical number of particles and self-organize into chains or scars. In this work, we study the packing of bidispersed packings on a sphere, and hence determine the interaction of bidispersity and curvature. The resultant configurations are nearly crystalline for low values of bidispersity and retain scar-like structures; these rapidly become disordered for intermediate values and approach a so-called Appollonian limit at the point where smaller particles can be entirely accommodated within the voids left by the larger particles. We connect our results with studies of bidispersed packings in the bulk and on flat surfaces from the literature on glassy systems and jamming. Supported by a Cottrell Award from the Research Corporation for Science Advancement.
Multi-dimensional Laplace transforms and applications
International Nuclear Information System (INIS)
Mughrabi, T.A.
1988-01-01
In this dissertation we establish new theorems for computing certain types of multidimensional Laplace transform pairs from known one-dimensional Laplace transforms. The theorems are applied to the most commonly used special functions and so we obtain many two and three dimensional Laplace transform pairs. As applications, some boundary value problems involving linear partial differential equations are solved by the use of multi-dimensional Laplace transformation. Also we establish some relations between the Laplace transformation and other integral transformation in two variables
Symbolic Multidimensional Scaling
P.J.F. Groenen (Patrick); Y. Terada
2015-01-01
markdownabstract__Abstract__ Multidimensional scaling (MDS) is a technique that visualizes dissimilarities between pairs of objects as distances between points in a low dimensional space. In symbolic MDS, a dissimilarity is not just a value but can represent an interval or even a histogram. Here,
Energy Technology Data Exchange (ETDEWEB)
Pesaran, Ahmad
2016-06-14
This presentation describes the thermal design of battery packs at the National Renewable Energy Laboratory. A battery thermal management system essential for xEVs for both normal operation during daily driving (achieving life and performance) and off-normal operation during abuse conditions (achieving safety). The battery thermal management system needs to be optimized with the right tools for the lowest cost. Experimental tools such as NREL's isothermal battery calorimeter, thermal imaging, and heat transfer setups are needed. Thermal models and computer-aided engineering tools are useful for robust designs. During abuse conditions, designs should prevent cell-to-cell propagation in a module/pack (i.e., keep the fire small and manageable). NREL's battery ISC device can be used for evaluating the robustness of a module/pack to cell-to-cell propagation.
Decontamination of pesticide packing using ionizing radiation
International Nuclear Information System (INIS)
Duarte, C.L.; Mori, M.N.; Kodama, Yasko; Oikawa, H.; Sampa, M.H.O.
2007-01-01
The Brazilian agriculture activities have consumed about 288,000 tons of pesticides per year conditioned in about 107,000,000 packing with weight of approximately 23,000 tons. The discharge of empty plastic packing of pesticides can be an environmental concern causing problems to human health, animals, and plants if done without inspection and monitoring. The objective of this work is to study the ionizing radiation effect in the main pesticides used in Brazil for plastic packing decontamination. Among the commercial pesticides, chlorpyrifos has significant importance because of its wide distribution and extensive use and persistence. The radiation-induced degradation of chlorpyrifos in liquid samples and in polyethylene pack was studied by gamma radiolysis. Packing of high-density polyethylene (HDPE) three layer coextruded, named COEX, contaminated with chlorpyrifos, were irradiated using both a multipurpose Co-60 gamma irradiator and a gamma source with 5000 Ci total activity Gamma cell type. The chemical analysis of the chlorpyrifos was made using a gas chromatography associated to the Mass Spectrometry-GCMS from Shimadzu Model QP 5000. Gamma radiation was efficient for removing chlorpyrifos from the plastic packing, in all studied cases
Decontamination of pesticide packing using ionizing radiation
Energy Technology Data Exchange (ETDEWEB)
Duarte, C.L. [Instituto de Pesquisas Energeticas e Nucleares-IPEN-CNEN/SP Av. Lineu Prestes 2.242, 05508-900, Sao Paulo, SP (Brazil)], E-mail: clduarte@ipen.br; Mori, M.N.; Kodama, Yasko; Oikawa, H.; Sampa, M.H.O. [Instituto de Pesquisas Energeticas e Nucleares-IPEN-CNEN/SP Av. Lineu Prestes 2.242, 05508-900, Sao Paulo, SP (Brazil)
2007-11-15
The Brazilian agriculture activities have consumed about 288,000 tons of pesticides per year conditioned in about 107,000,000 packing with weight of approximately 23,000 tons. The discharge of empty plastic packing of pesticides can be an environmental concern causing problems to human health, animals, and plants if done without inspection and monitoring. The objective of this work is to study the ionizing radiation effect in the main pesticides used in Brazil for plastic packing decontamination. Among the commercial pesticides, chlorpyrifos has significant importance because of its wide distribution and extensive use and persistence. The radiation-induced degradation of chlorpyrifos in liquid samples and in polyethylene pack was studied by gamma radiolysis. Packing of high-density polyethylene (HDPE) three layer coextruded, named COEX, contaminated with chlorpyrifos, were irradiated using both a multipurpose Co-60 gamma irradiator and a gamma source with 5000 Ci total activity Gamma cell type. The chemical analysis of the chlorpyrifos was made using a gas chromatography associated to the Mass Spectrometry-GCMS from Shimadzu Model QP 5000. Gamma radiation was efficient for removing chlorpyrifos from the plastic packing, in all studied cases.
Numeric invariants from multidimensional persistence
Energy Technology Data Exchange (ETDEWEB)
Skryzalin, Jacek [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Carlsson, Gunnar [Stanford Univ., Stanford, CA (United States)
2017-05-19
In this paper, we analyze the space of multidimensional persistence modules from the perspectives of algebraic geometry. We first build a moduli space of a certain subclass of easily analyzed multidimensional persistence modules, which we construct specifically to capture much of the information which can be gained by using multidimensional persistence over one-dimensional persistence. We argue that the global sections of this space provide interesting numeric invariants when evaluated against our subclass of multidimensional persistence modules. Lastly, we extend these global sections to the space of all multidimensional persistence modules and discuss how the resulting numeric invariants might be used to study data.
Quasi-human seniority-order algorithm for unequal circles packing
International Nuclear Information System (INIS)
Zhu, Dingju
2016-01-01
In the existing methods for solving unequal circles packing problems, the initial configuration is given arbitrarily or randomly, but the impact of different initial configurations for existing packing algorithm to the speed of existing packing algorithm solving unequal circles packing problems is very large. The quasi-human seniority-order algorithm proposed in this paper can generate a better initial configuration for existing packing algorithm to accelerate the speed of existing packing algorithm solving unequal circles packing problems. In experiments, the quasi-human seniority-order algorithm is applied to generate better initial configurations for quasi-physical elasticity methods to solve the unequal circles packing problems, and the experimental results show that the proposed quasi-human seniority-order algorithm can greatly improve the speed of solving the problem.
Fast searching in packed strings
DEFF Research Database (Denmark)
Bille, Philip
2011-01-01
Given strings P and Q the (exact) string matching problem is to find all positions of substrings in Q matching P. The classical Knuth–Morris–Pratt algorithm [SIAM J. Comput. 6 (2) (1977) 323–350] solves the string matching problem in linear time which is optimal if we can only read one character...... at the time. However, most strings are stored in a computer in a packed representation with several characters in a single word, giving us the opportunity to read multiple characters simultaneously. In this paper we study the worst-case complexity of string matching on strings given in packed representation....... Let m⩽n be the lengths P and Q, respectively, and let σ denote the size of the alphabet. On a standard unit-cost word-RAM with logarithmic word size we present an algorithm using timeO(nlogσn+m+occ). Here occ is the number of occurrences of P in Q. For m=o(n) this improves the O(n) bound of the Knuth...
McDonald's Corp., Oak Brook, IL.
One of five McDonald's Action Packs, this learning package introduces intermediate grade students to basic economic concepts. The fourteen activities include the topics of consumption (4 activities), production (5), the market system (3), a pretest, and a posttest. Specific titles under consumption include The Wonderful Treasure Tree (introduction…
The multidimensional nucleon structure
Directory of Open Access Journals (Sweden)
Pasquini Barbara
2016-01-01
Full Text Available We discuss different kinds of parton distributions, which allow one to obtain a multidimensional picture of the internal structure of the nucleon. We use the concept of generalized transverse momentum dependent parton distributions and Wigner distributions, which combine the features of transverse-momentum dependent parton distributions and generalized parton distributions. We show examples of these functions within a phenomenological quark model, with focus on the role of the spin-spin and spin-orbit correlations of quarks.
Constraint theory multidimensional mathematical model management
Friedman, George J
2017-01-01
Packed with new material and research, this second edition of George Friedman’s bestselling Constraint Theory remains an invaluable reference for all engineers, mathematicians, and managers concerned with modeling. As in the first edition, this text analyzes the way Constraint Theory employs bipartite graphs and presents the process of locating the “kernel of constraint” trillions of times faster than brute-force approaches, determining model consistency and computational allowability. Unique in its abundance of topological pictures of the material, this book balances left- and right-brain perceptions to provide a thorough explanation of multidimensional mathematical models. Much of the extended material in this new edition also comes from Phan Phan’s PhD dissertation in 2011, titled “Expanding Constraint Theory to Determine Well-Posedness of Large Mathematical Models.” Praise for the first edition: "Dr. George Friedman is indisputably the father of the very powerful methods of constraint theory...
Consistency Check for the Bin Packing Constraint Revisited
Dupuis, Julien; Schaus, Pierre; Deville, Yves
The bin packing problem (BP) consists in finding the minimum number of bins necessary to pack a set of items so that the total size of the items in each bin does not exceed the bin capacity C. The bin capacity is common for all the bins.
DEFF Research Database (Denmark)
Andersen, Henrik; Ritter, Thomas
Ever seen a growth strategies fail because it was not connect ed to the firm’s customer base? Or a customer relationship strategy falters just because it was the wrong thing to do with that given customer? This article presents the six pack model, a tool that makes growth profitable and predictable....... Not all customers can and should grow – thus a firm needs to classify its customers in order to implement the right customer strategy....
Argo packing friction research update
International Nuclear Information System (INIS)
VanTassell, D.M.
1994-01-01
This paper focuses on the issue of valve packing friction and its affect on the operability of motor- and air-operated valves (MOVs and AOVs). At this time, most nuclear power plants are required to perform postmaintenance testing following a packing adjustment or replacement. In many cases, the friction generated by the packing does not impact the operability window of a valve. However, to date there has not been a concerted effort to substantiate this claim. To quantify the effects of packing friction, it has become necessary to develop a formula to predict the friction effects accurately. This formula provides a much more accurate method of predicting packing friction than previously used factors based strictly on stem diameter. Over the past 5 years, Argo Packing Company has been developing and testing improved graphite packing systems at research facilities, such as AECL Chalk River and Wyle Laboratories. Much of this testing has centered around reducing and predicting friction that is related to packing. In addition, diagnostic testing for Generic Letter 89-10 MOVs and AOVs has created a significant data base. In July 1992 Argo asked several utilities to provide running load data that could be used to quantify packing friction repeatability and predictability. This technical paper provides the basis to predict packing friction, which will improve calculations for thrust requirements for Generic Leter 89-10 and future AOV programs. In addition, having an accurate packing friction formula will improve packing performance when low running loads are identified that would indicate insufficient sealing force
Multidimensional Models of Information Need
Yun-jie (Calvin) Xu; Kai Huang (Joseph) Tan
2009-01-01
User studies in information science have recognised relevance as a multidimensional construct. An implication of multidimensional relevance is that a user's information need should be modeled by multiple data structures to represent different relevance dimensions. While the extant literature has attempted to model multiple dimensions of a user's information need, the fundamental assumption that a multidimensional model is better than a uni-dimensional model has not been addressed. This study ...
Direct contact condensation in packed beds
Energy Technology Data Exchange (ETDEWEB)
Li, Yi; Klausner, James F.; Mei, Renwei; Knight, Jessica [Department of Mechanical and Aerospace Engineering, University of Florida, Gainesville, FL 32611 (United States)
2006-12-15
A diffusion driven desalination process was recently described where a very effective direct contact condenser with a packed bed is used to condense water vapor out of an air/vapor mixture. A laboratory scale direct contact condenser has been fabricated as a twin tower structure with two stages, co-current and countercurrent. Experiments have been operated in each stage with respective saturated air inlet temperatures of 36, 40 and 43{sup o}C. The temperature and humidity data have been collected at the inlet and exit of the packed bed for different water to air mass flow ratios that vary between 0 and 2.5. A one-dimensional model based on conservation principles has been developed, which predicts the variation of temperature, humidity, and condensation rate through the condenser stages. Agreement between the model and experiments is very good. It is observed that the countercurrent flow stage condensation effectiveness is significantly higher than that for the co-current stage. The condensation heat and mass transfer rates were found to decrease when water blockages occur within the packed bed. Using high-speed digital cinematography, it was observed that this problem can occur at any operating condition, and is dependent on the packing surface wetting characteristics. This observation is used to explain the requirement for two different empirical constants, depending on packing diameter, suggested by Onda for the air side mass transfer coefficient correlation. (author)
International Nuclear Information System (INIS)
Hanson, R.G.; Johnson, E.C.; Carlson, K.E.; Chou, C.Y.; Davis, C.B.; Martin, R.P.; Riemke, R.A.; Wagner, R.J.
1992-07-01
This report documents ten developmental assessment problems which were used to test the multidimensional component in RELAP5/MOD2.5, Version 3w. The problems chosen were a rigid body rotation problem, a pure radial symmetric flow problem, an r-θ symmetric flow problem, a fall problem, a rest problem, a basic one-dimensional flow test problem, a gravity wave problem, a tank draining problem, a flow through the center problem, and coverage analysis using PIXIE. The multidimensional code calculations are compared to analytical solutions and one-dimensional code calculations. The discussion section of each problem contains information relative to the code's ability to simulate these problems
To Pack or Not to Pack? A Randomized Trial of Vaginal Packing After Vaginal Reconstructive Surgery.
Westermann, Lauren B; Crisp, Catrina C; Oakley, Susan H; Mazloomdoost, Donna; Kleeman, Steven D; Benbouajili, Janine M; Ghodsi, Vivian; Pauls, Rachel N
2016-01-01
Placement of vaginal packing after pelvic reconstructive surgery is common; however, little evidence exists to support the practice. Furthermore, patients have reported discomfort from the packs. We describe pain and satisfaction in women treated with and without vaginal packing. This institutional review board-approved randomized-controlled trial enrolled patients undergoing vaginal hysterectomy with prolapse repairs. The primary outcome was visual analog scales (VASs) for pain on postoperative day 1. Allocation to "packing" ("P") or "no-packing" ("NP") arms occurred intraoperatively at the end of surgery. Visual analog scales regarding pain and satisfaction were completed early on postoperative day 1 before packing removal. Visual analog scale scores for pain, satisfaction, and bother attributable to packing were recorded before discharge. All packing and perineal pads were weighed to calculate a "postoperative vaginal blood loss." Perioperative data were collected from the hospital record. Our sample size estimation required 74 subjects. Ninety-three women were enrolled. After exclusions, 77 were randomized (P, 37; NP, 40). No differences were found in surgical information, hemoglobin levels, or narcotic use between groups. However, "postoperative vaginal blood loss" was greater in packed subjects (P discharge (P, 35.0 vs NP, 40.0; P = 0.43] were not significantly different between treatment arms. Likewise, VAS scores for satisfaction before removal of packing (P, 81.0 vs NP, 90.0; P = 0.08] and before discharge (P, 90.0 vs NP, 90.5; P = 0.60] were not significantly different. Packed patients noted lower nursing verbal pain scores (P = 0.04) and used less ketorolac (P = 0.01). Bother from packing was low overall. Although there was no difference based on VAS, women receiving vaginal packing had lower nursing documented pain and used less ketorolac than packed women. Vaginal packing may provide benefit and can remain part of the surgical practice.
Visual modeling in an analysis of multidimensional data
Zakharova, A. A.; Vekhter, E. V.; Shklyar, A. V.; Pak, A. J.
2018-01-01
The article proposes an approach to solve visualization problems and the subsequent analysis of multidimensional data. Requirements to the properties of visual models, which were created to solve analysis problems, are described. As a perspective direction for the development of visual analysis tools for multidimensional and voluminous data, there was suggested an active use of factors of subjective perception and dynamic visualization. Practical results of solving the problem of multidimensional data analysis are shown using the example of a visual model of empirical data on the current state of studying processes of obtaining silicon carbide by an electric arc method. There are several results of solving this problem. At first, an idea of possibilities of determining the strategy for the development of the domain, secondly, the reliability of the published data on this subject, and changes in the areas of attention of researchers over time.
[Intraoperative multidimensional visualization].
Sperling, J; Kauffels, A; Grade, M; Alves, F; Kühn, P; Ghadimi, B M
2016-12-01
Modern intraoperative techniques of visualization are increasingly being applied in general and visceral surgery. The combination of diverse techniques provides the possibility of multidimensional intraoperative visualization of specific anatomical structures. Thus, it is possible to differentiate between normal tissue and tumor tissue and therefore exactly define tumor margins. The aim of intraoperative visualization of tissue that is to be resected and tissue that should be spared is to lead to a rational balance between oncological and functional results. Moreover, these techniques help to analyze the physiology and integrity of tissues. Using these methods surgeons are able to analyze tissue perfusion and oxygenation. However, to date it is not clear to what extent these imaging techniques are relevant in the clinical routine. The present manuscript reviews the relevant modern visualization techniques focusing on intraoperative computed tomography and magnetic resonance imaging as well as augmented reality, fluorescence imaging and optoacoustic imaging.
Multidimensional HAM-conditions
DEFF Research Database (Denmark)
Hansen, Ernst Jan de Place
Heat, Air and Moisture (HAM) conditions, experimental data are needed. Tests were performed in the large climate simulator at SBi involving full-scale wall elements. The elements were exposed for steady-state conditions, and temperature cycles simulating April and September climate in Denmark....... The effect on the moisture and temperature conditions of the addition of a vapour barrier and an outer cladding on timber frame walls was studied. The report contains comprehensive appendices documenting the full-scale tests. The tests were performed as a part of the project 'Model for Multidimensional Heat......, Air and Moisture Conditions in Building Envelope Components' carried out as a co-project between DTU Byg and SBi....
Pottmann, Helmut
2015-03-03
This paper is an overview of architectural structures which are either composed of polyhedral cells or closely related to them. We introduce the concept of a support structure of such a polyhedral cell packing. It is formed by planar quads and obtained by connecting corresponding vertices in two combinatorially equivalent meshes whose corresponding edges are coplanar and thus determine planar quads. Since corresponding triangle meshes only yield trivial structures, we focus on support structures associated with quad meshes or hex-dominant meshes. For the quadrilateral case, we provide a short survey of recent research which reveals beautiful relations to discrete differential geometry. Those are essential for successfully initializing numerical optimization schemes for the computation of quad-based support structures. Hex-dominant structures may be designed via Voronoi tessellations, power diagrams, sphere packings and various extensions of these concepts. Apart from the obvious application as load-bearing structures, we illustrate here a new application to shading and indirect lighting. On a higher level, our work emphasizes the interplay between geometry, optimization, statics, and manufacturing, with the overall aim of combining form, function and fabrication into novel integrated design tools.
Flooding characteristics of Goodloe packing
International Nuclear Information System (INIS)
Begovich, J.M.; Watson, J.S.
1976-08-01
Experimental flooding data for the countercurrent flow of air and water in a 7.62-cm-diam glass column filled with Goodloe packing were compared with a correlation reported by the packing manufacturer. Flooding rates observed in this study were as low as one-half those predicted by the correlation. Rearranging the packing by inverting the column and removing some packing segments yielded results similar to the correlation for liquid-to-gas (L/G) mass flow rate ratios greater than 10, but the experimental flooding curve fell significantly below the correlation at lower L/G ratios. When the column was repacked with new packing, the results were essentially the same as those obtained in the inverted column. Thus, it is believed that a carefully packed column is more likely to yield flooding rates similar to those obtained in the new or inverted columns rather than rates predicted by the original correlation
Nonparametric Bayesian inference for multidimensional compound Poisson processes
Gugushvili, S.; van der Meulen, F.; Spreij, P.
2015-01-01
Given a sample from a discretely observed multidimensional compound Poisson process, we study the problem of nonparametric estimation of its jump size density r0 and intensity λ0. We take a nonparametric Bayesian approach to the problem and determine posterior contraction rates in this context,
Numerical Simulation on Dense Packing of Granular Materials by Container Oscillation
Jun Liu; Dongxu You
2013-01-01
The packing of granular materials is a basic and important problem in geomechanics. An approach, which generates dense packing of spheres confined in cylindrical and cuboidal containers in three steps, is introduced in this work. A loose packing structure is first generated by means of a reference lattice method. Then a dense packing structure is obtained in a container by simulating dropping of particles under gravitational forces. Furthermore, a scheme that makes the bottom boundary fluctua...
Pack stability in dip faces fitted with scraper conveyors
Energy Technology Data Exchange (ETDEWEB)
Schwartzmann, R
1978-01-01
This paper presents an account of an investigation conducted by CERCHAR, at the request of HBNPC, into the problems of goafside pack stability. Winning method and support and stowing techniques are described. Sets out the study methods used: systematic measurement (by direct or remote means) using an instrument developed by CERCHAR to investigate all aspects of in situ pack behaviour: settling, stresses, pressure on supports, etc. Gives the results of the investigation (tables and graphs) load-bearing capacity of the supports, deformation of the surrounding rock, convergence and stresses in the pack (figures, graphs), resistance of support-timber screen, model of in situ pack behaviour. Detailed conclusions (potential techniques, detailed study, practical improvements in packing techniques) are presented.
Energy Technology Data Exchange (ETDEWEB)
Chmielewski, A G [Institute of Nuclear Chemistry and Technology, Warsaw (Poland)
2006-07-01
Joint FAO/IAEA/WHO Expert Committee approved the use of radiation treatment of foods. Nowadays food packaging are mostly made of plastics, natural or synthetic, therefore effect of irradiation on these materials is crucial for packing engineering for food irradiation technology. By selecting the right polymer materials for food packaging it can be ensured that the critical elements of material and product performance are not compromised. When packaging materials are in contact with food at the time of irradiation that regulatory approvals sometimes apply. The review of the R-and-D and technical papers regarding material selection, testing and approval is presented in the report. The most information come from the USA where this subject is well elaborated, the International Atomic Energy Agency (IAEA) reports are reviewed as well. The report can be useful for scientists and food irradiation plants operators. (author)
International Nuclear Information System (INIS)
Chmielewski, A.G.
2006-01-01
Joint FAO/IAEA/WHO Expert Committee approved the use of radiation treatment of foods. Nowadays food packaging are mostly made of plastics, natural or synthetic, therefore effect of irradiation on these materials is crucial for packing engineering for food irradiation technology. By selecting the right polymer materials for food packaging it can be ensured that the critical elements of material and product performance are not compromised. When packaging materials are in contact with food at the time of irradiation that regulatory approvals sometimes apply. The review of the R-and-D and technical papers regarding material selection, testing and approval is presented in the report. The most information come from the USA where this subject is well elaborated, the International Atomic Energy Agency (IAEA) reports are reviewed as well. The report can be useful for scientists and food irradiation plants operators. (author)
Multidimensional Databases and Data Warehousing
Jensen, Christian
2010-01-01
The present book's subject is multidimensional data models and data modeling concepts as they are applied in real data warehouses. The book aims to present the most important concepts within this subject in a precise and understandable manner. The book's coverage of fundamental concepts includes data cubes and their elements, such as dimensions, facts, and measures and their representation in a relational setting; it includes architecture-related concepts; and it includes the querying of multidimensional databases.The book also covers advanced multidimensional concepts that are considered to b
Energy Technology Data Exchange (ETDEWEB)
Rich, Hans Walter [Kernkraftwerk Goesgen-Daeniken AG, Daeniken (Switzerland)
2012-07-01
In 2005 the asbestos cement cooling tower packing was replaced by plastic material. Two years later, the packing showed strong deformations, deposits of solids and weight gain. At the end of 2007 parts of the packing collapsed into the cooling tower basin. Investigations were made, revealing that the thickness of the packing foil was too low and that packing geometry and biofilms on the surface of the packing favoured deposition of solids. Successful measures were taken to solve the problems. (orig.)
Random packing of digitized particles
Korte, de A.C.J.; Brouwers, H.J.H.
2013-01-01
The random packing of regularly and irregularly shaped particles has been studied extensively. Within this paper, packing is studied from the perspective of digitized particles. These digitized particles are developed for and used in cellular automata systems, which are employed for the simple
Random packing of digitized particles
de Korte, A.C.J.; Brouwers, Jos
2012-01-01
The random packing of regularly and irregularly shaped particles has been studied extensively. Within this paper, packing is studied from the perspective of digitized particles. These digitized particles are developed for and used in cellular automata systems, which are employed for the simple
International Nuclear Information System (INIS)
Cumming, D.
1995-01-01
The Bruce B Valve Packing Program began in 1987. The early history and development were presented at the 1992 International CANDU Maintenance conference. This presentation covers the evolution of the Bruce B Valve Packing Program over the period 1992 to 1995. (author)
Matching and Compression of Strings with Automata and Word Packing
DEFF Research Database (Denmark)
Skjoldjensen, Frederik Rye; Gørtz, Inge Li; Thomassen, Carsten
pattern queries. In the deterministic variant the goal is to solve the string indexing problem without any randomization (at preprocessing time or query time). In the packed variant the strings are stored with several character in a single word, giving us the opportunity to read multiple characters...... in (deterministic) time O (m= + logm + log log ) ; where = w= log is the number of characters packed in a word of size w = (log n). Our query time is always at least as good as the previous best known bounds and whenever several characters are packed in a word, i.e., log w, the query times are faster. Dynamic...
An example of multidimensional analysis: Discriminant analysis
International Nuclear Information System (INIS)
Lutz, P.
1990-01-01
Among the approaches on the data multi-dimensional analysis, lectures on the discriminant analysis including theoretical and practical aspects are presented. The discrimination problem, the analysis steps and the discrimination categories are stressed. Examples on the descriptive historical analysis, the discrimination for decision making, the demonstration and separation of the top quark are given. In the linear discriminant analysis the following subjects are discussed: Huyghens theorem, projection, discriminant variable, geometrical interpretation, case for g=2, classification method, separation of the top events. Criteria allowing the obtention of relevant results are included [fr
Nasal packing with ventilated nasal packs; a comparison with traditional vaseline nasal pack
International Nuclear Information System (INIS)
Alam, J.; Siddiqui, M.W.; Abbas, A.; Sami, M.; Ayub, Z.
2017-01-01
To compare the benefits of ventilated nasal packing with traditional vaseline guaze nasal packing. Study Design: Randomized controlled trial. Place and Duration of Study: This study was conducted at CMH Multan, from Jun 2014 to Dec 2014. Material and Methods: In this study, sample size of 80 patients was calculated using WHO calculator. Patients were divided in two groups using lottery method endotracheal tube and piece of surgical glove filled with ribbon guaze was utilized for fabricated ventilated nasal pack and compared with traditional nasal packs. Nasal obstruction and sleep disturbance were studied at eight hours and twenty-four hours following surgery using visual analog scale. Results: Mean nasal obstruction with ventilated nasal pack was 45.62 +- 6.17 and with Vaseline nasal pack was 77.67 +- 4.85 which was statistically significant (p=0.001) in both the groups. Mean sleep disturbance in both the groups was 46.32 +- 5.23 and 68.75 +- 2.70 respectively which was statistically significant (p=0.001) in both the groups. Conclusion: Patients with ventilated nasal packs were found to have better tolerance to nasal packs due to less nasal obstruction and sleep disturbance
Benchmarking the Multidimensional Stellar Implicit Code MUSIC
Goffrey, T.; Pratt, J.; Viallet, M.; Baraffe, I.; Popov, M. V.; Walder, R.; Folini, D.; Geroux, C.; Constantino, T.
2017-04-01
We present the results of a numerical benchmark study for the MUltidimensional Stellar Implicit Code (MUSIC) based on widely applicable two- and three-dimensional compressible hydrodynamics problems relevant to stellar interiors. MUSIC is an implicit large eddy simulation code that uses implicit time integration, implemented as a Jacobian-free Newton Krylov method. A physics based preconditioning technique which can be adjusted to target varying physics is used to improve the performance of the solver. The problems used for this benchmark study include the Rayleigh-Taylor and Kelvin-Helmholtz instabilities, and the decay of the Taylor-Green vortex. Additionally we show a test of hydrostatic equilibrium, in a stellar environment which is dominated by radiative effects. In this setting the flexibility of the preconditioning technique is demonstrated. This work aims to bridge the gap between the hydrodynamic test problems typically used during development of numerical methods and the complex flows of stellar interiors. A series of multidimensional tests were performed and analysed. Each of these test cases was analysed with a simple, scalar diagnostic, with the aim of enabling direct code comparisons. As the tests performed do not have analytic solutions, we verify MUSIC by comparing it to established codes including ATHENA and the PENCIL code. MUSIC is able to both reproduce behaviour from established and widely-used codes as well as results expected from theoretical predictions. This benchmarking study concludes a series of papers describing the development of the MUSIC code and provides confidence in future applications.
Franco-Correa, A.
2014-01-01
This paper deals with the problem of selecting the unit of analysis in multidimensional poverty analyses, which is a central decision to take, both from academic and normative points of view. The paper compares the results of an individual-level Multidimensional Poverty Index for Chile, Colombia,
On the perfect hexagonal packing of rods
International Nuclear Information System (INIS)
Starostin, E L
2006-01-01
In most cases the hexagonal packing of fibrous structures or rods extremizes the energy of interaction between strands. If the strands are not straight, then it is still possible to form a perfect hexatic bundle. Conditions under which the perfect hexagonal packing of curved tubular structures may exist are formulated. Particular attention is given to closed or cycled arrangements of the rods like in the DNA toroids and spools. The closure or return constraints of the bundle result in an allowable group of automorphisms of the cross-sectional hexagonal lattice. The structure of this group is explored. Examples of open helical-like and closed toroidal-like bundles are presented. An expression for the elastic energy of a perfectly packed bundle of thin elastic rods is derived. The energy accounts for both the bending and torsional stiffnesses of the rods. It is shown that equilibria of the bundle correspond to solutions of a variational problem formulated for the curve representing the axis of the bundle. The functional involves a function of the squared curvature under the constraints on the total torsion and the length. The Euler-Lagrange equations are obtained in terms of curvature and torsion and due to the existence of the first integrals the problem is reduced to the quadrature. The three-dimensional shape of the bundle may be readily reconstructed by integration of the Ilyukhin-type equations in special cylindrical coordinates. The results are of universal nature and are applicable to various fibrous structures, in particular, to intramolecular liquid crystals formed by DNA condensed in toroids or packed inside the viral capsids
International Nuclear Information System (INIS)
Blackbee, B.A.
1977-10-01
To enable Naval Emergency Monitoring Teams to fulfil their role in the field it was necessary to locate or design a replacement filter pack for the collection of radioactive iodine air samples. Collaboration with the Berkeley Laboratories of the Central Electricity Generating Board provided the necessary starting point for a suitable type of package. Further development by NGTE (West Drayton) yielded the improved filter pack which is the subject of this memorandum. (author)
A comparison of multidimensional scaling methods for perceptual mapping
Bijmolt, T.H.A.; Wedel, M.
Multidimensional scaling has been applied to a wide range of marketing problems, in particular to perceptual mapping based on dissimilarity judgments. The introduction of methods based on the maximum likelihood principle is one of the most important developments. In this article, the authors compare
Application of Andrew's Plots to Visualization of Multidimensional Data
Grinshpun, Vadim
2016-01-01
Importance: The article raises a point of visual representation of big data, recently considered to be demanded for many scientific and real-life applications, and analyzes particulars for visualization of multi-dimensional data, giving examples of the visual analytics-related problems. Objectives: The purpose of this paper is to study application…
Almost-sure identifiability of multidimensional harmonic retrieval
Jiang, T; Sidiropoulos, ND; ten Berge, JMF
Two-dimensional (2-D) and, more generally, multidimensional harmonic retrieval is of interest in a variety of applications, including transmitter localization and joint time and frequency offset estimation in wireless communications. The associated identifiability problem is key in understanding the
Routing Trains Through Railway Junctions: A New Set Packing Approach
DEFF Research Database (Denmark)
Lusby, Richard; Larsen, Jesper; Ryan, David
how the problem can be formulated as a set packing model. To exploit the structure of the problem we present a solution procedure which entails solving the dual of this formulation through the dynamic addition of violated cuts (primal variables). A discussion of the variable (train path) generation...
Contributions to multidimensional quadrature formulas
International Nuclear Information System (INIS)
Guenther, C.
1976-11-01
The general objective of this paper is to construct multidimensional quadrature formulas similar to the Gaussian Quadrature Formulas in one dimension. The correspondence between these formulas and orthogonal and nonnegative polynomials is established. One part of the paper considers the construction of multidimensional quadrature formulas using only methods of algebraic geometry, on the other part it is tried to obtain results on quadrature formulas with real nodes and, if possible, with positive weights. The results include the existence of quadrature formulas, information on the number resp. on the maximum possible number of points in the formulas for given polynomial degree N and the construction of formulas. (orig.) [de
Multi-Dimensional Path Queries
DEFF Research Database (Denmark)
Bækgaard, Lars
1998-01-01
to create nested path structures. We present an SQL-like query language that is based on path expressions and we show how to use it to express multi-dimensional path queries that are suited for advanced data analysis in decision support environments like data warehousing environments......We present the path-relationship model that supports multi-dimensional data modeling and querying. A path-relationship database is composed of sets of paths and sets of relationships. A path is a sequence of related elements (atoms, paths, and sets of paths). A relationship is a binary path...
Multidimensional real analysis I differentiation
Duistermaat, J J; van Braam Houckgeest, J P
2004-01-01
Part one of the authors' comprehensive and innovative work on multidimensional real analysis. This book is based on extensive teaching experience at Utrecht University and gives a thorough account of differential analysis in multidimensional Euclidean space. It is an ideal preparation for students who wish to go on to more advanced study. The notation is carefully organized and all proofs are clean, complete and rigorous. The authors have taken care to pay proper attention to all aspects of the theory. In many respects this book presents an original treatment of the subject and it contains man
A MULTIDIMENSIONAL AND MULTIPHYSICS APPROACH TO NUCLEAR FUEL BEHAVIOR SIMULATION
Energy Technology Data Exchange (ETDEWEB)
R. L. Williamson; J. D. Hales; S. R. Novascone; M. R. Tonks; D. R. Gaston; C. J. Permann; D. Andrs; R. C. Martineau
2012-04-01
Important aspects of fuel rod behavior, for example pellet-clad mechanical interaction (PCMI), fuel fracture, oxide formation, non-axisymmetric cooling, and response to fuel manufacturing defects, are inherently multidimensional in addition to being complicated multiphysics problems. Many current modeling tools are strictly 2D axisymmetric or even 1.5D. This paper outlines the capabilities of a new fuel modeling tool able to analyze either 2D axisymmetric or fully 3D models. These capabilities include temperature-dependent thermal conductivity of fuel; swelling and densification; fuel creep; pellet fracture; fission gas release; cladding creep; irradiation growth; and gap mechanics (contact and gap heat transfer). The need for multiphysics, multidimensional modeling is then demonstrated through a discussion of results for a set of example problems. The first, a 10-pellet rodlet, demonstrates the viability of the solution method employed. This example highlights the effect of our smeared cracking model and also shows the multidimensional nature of discrete fuel pellet modeling. The second example relies on our the multidimensional, multiphysics approach to analyze a missing pellet surface problem. As a final example, we show a lower-length-scale simulation coupled to a continuum-scale simulation.
A Multidimensional Software Engineering Course
Barzilay, O.; Hazzan, O.; Yehudai, A.
2009-01-01
Software engineering (SE) is a multidimensional field that involves activities in various areas and disciplines, such as computer science, project management, and system engineering. Though modern SE curricula include designated courses that address these various subjects, an advanced summary course that synthesizes them is still missing. Such a…
Multidimensional Databases and Data Warehousing
DEFF Research Database (Denmark)
Jensen, Christian S.; Pedersen, Torben Bach; Thomsen, Christian
The present book's subject is multidimensional data models and data modeling concepts as they are applied in real data warehouses. The book aims to present the most important concepts within this subject in a precise and understandable manner. The book's coverage of fundamental concepts includes...
Recycling Behavior: A Multidimensional Approach
Meneses, Gonzalo Diaz; Palacio, Asuncion Beerli
2005-01-01
This work centers on the study of consumer recycling roles to examine the sociodemographic and psychographic profile of the distribution of recycling tasks and roles within the household. With this aim in mind, an empirical work was carried out, the results of which suggest that recycling behavior is multidimensional and comprises the undertaking…
Multidimensional diffusion processes
Stroock, Daniel W
1997-01-01
From the reviews: "… Both the Markov-process approach and the Itô approach … have been immensely successful in diffusion theory. The Stroock-Varadhan book, developed from the historic 1969 papers by its authors, presents the martingale-problem approach as a more powerful - and, in certain regards, more intrinsic-means of studying the foundations of the subject. […] … the authors make the uncompromising decision not "to proselytise by intimidating the reader with myriad examples demonstrating the full scope of the techniques", but rather to persuade the reader "with a careful treatment of just one problem to which they apply". […] Most of the main tools of stochastic-processes theory are used, ..but it is the formidable combination of probability theory with analysis … which is the core of the work. […] I have emphasized the great importance of the Stroock-Varadhan book. It contains a lot more than I have indicated; in particular, its many exercises conain much interesting material. For immediat...
Testlet-Based Multidimensional Adaptive Testing.
Frey, Andreas; Seitz, Nicki-Nils; Brandt, Steffen
2016-01-01
Multidimensional adaptive testing (MAT) is a highly efficient method for the simultaneous measurement of several latent traits. Currently, no psychometrically sound approach is available for the use of MAT in testlet-based tests. Testlets are sets of items sharing a common stimulus such as a graph or a text. They are frequently used in large operational testing programs like TOEFL, PISA, PIRLS, or NAEP. To make MAT accessible for such testing programs, we present a novel combination of MAT with a multidimensional generalization of the random effects testlet model (MAT-MTIRT). MAT-MTIRT compared to non-adaptive testing is examined for several combinations of testlet effect variances (0.0, 0.5, 1.0, and 1.5) and testlet sizes (3, 6, and 9 items) with a simulation study considering three ability dimensions with simple loading structure. MAT-MTIRT outperformed non-adaptive testing regarding the measurement precision of the ability estimates. Further, the measurement precision decreased when testlet effect variances and testlet sizes increased. The suggested combination of the MTIRT model therefore provides a solution to the substantial problems of testlet-based tests while keeping the length of the test within an acceptable range.
Testlet-based Multidimensional Adaptive Testing
Directory of Open Access Journals (Sweden)
Andreas Frey
2016-11-01
Full Text Available Multidimensional adaptive testing (MAT is a highly efficient method for the simultaneous measurement of several latent traits. Currently, no psychometrically sound approach is available for the use of MAT in testlet-based tests. Testlets are sets of items sharing a common stimulus such as a graph or a text. They are frequently used in large operational testing programs like TOEFL, PISA, PIRLS, or NAEP. To make MAT accessible for such testing programs, we present a novel combination of MAT with a multidimensional generalization of the random effects testlet model (MAT-MTIRT. MAT-MTIRT compared to non-adaptive testing is examined for several combinations of testlet effect variances (0.0, 0.5, 1.0, 1.5 and testlet sizes (3 items, 6 items, 9 items with a simulation study considering three ability dimensions with simple loading structure. MAT-MTIRT outperformed non-adaptive testing regarding the measurement precision of the ability estimates. Further, the measurement precision decreased when testlet effect variances and testlet sizes increased. The suggested combination of the MTIRT model therefore provides a solution to the substantial problems of testlet-based tests while keeping the length of the test within an acceptable range.
Cylinder valve packing nut studies
Energy Technology Data Exchange (ETDEWEB)
Blue, S.C. [Martin Marietta Energy Systems, Inc., Paducah, KY (United States)
1991-12-31
The design, manufacture, and use of cylinder valve packing nuts have been studied to improve their resistance to failure from stress corrosion cracking. Stress frozen photoelastic models have been analyzed to measure the stress concentrations at observed points of failure. The load effects induced by assembly torque and thermal expansion of stem packing were observed by strain gaging nuts. The effects of finishing operations and heat treatment were studied by the strain gage hole boring and X-ray methods. Modifications of manufacturing and operation practices are reducing the frequency of stress corrosion failures.
[Multidimensional family therapy: which influences, which specificities?].
Bonnaire, C; Bastard, N; Couteron, J-P; Har, A; Phan, O
2014-10-01
Among illegal psycho-active drugs, cannabis is the most consumed by French adolescents. Multidimensional family therapy (MDFT) is a family-based outpatient therapy which has been developed for adolescents with drug and behavioral problems. MDFT has shown its effectiveness in adolescents with substance abuse disorders (notably cannabis abuse) not only in the United States but also in Europe (International Cannabis Need of Treatment project). MDFT is a multidisciplinary approach and an evidence-based treatment, at the crossroads of developmental psychology, ecological theories and family therapy. Its psychotherapeutic techniques find its roots in a variety of approaches which include systemic family therapy and cognitive therapy. The aims of this paper are: to describe all the backgrounds of MDFT by highlighting its characteristics; to explain how structural and strategy therapies have influenced this approach; to explore the links between MDFT, brief strategic family therapy and multi systemic family therapy; and to underline the specificities of this family therapy method. The multidimensional family therapy was created on the bases of 1) the integration of multiple therapeutic techniques stemming from various family therapy theories; and 2) studies which have shown family therapy efficiency. Several trials have shown a better efficiency of MDFT compared to group treatment, cognitive-behavioral therapy and home-based treatment. Studies have also highlighted that MDFT led to superior treatment outcomes, especially among young people with severe drug use and psychiatric co-morbidities. In the field of systemic family therapies, MDFT was influenced by: 1) the structural family therapy (S. Minuchin), 2) the strategic family theory (J. Haley), and 3) the intergenerational family therapy (Bowen and Boszormenyi-Nagy). MDFT has specific aspects: MDFT therapists think in a multidimensional perspective (because an adolescent's drug abuse is a multidimensional disorder), they
Cluster Oriented Spatio Temporal Multidimensional Data Visualization of Earthquakes in Indonesia
Directory of Open Access Journals (Sweden)
Mohammad Nur Shodiq
2016-03-01
Full Text Available Spatio temporal data clustering is challenge task. The result of clustering data are utilized to investigate the seismic parameters. Seismic parameters are used to describe the characteristics of earthquake behavior. One of the effective technique to study multidimensional spatio temporal data is visualization. But, visualization of multidimensional data is complicated problem. Because, this analysis consists of observed data cluster and seismic parameters. In this paper, we propose a visualization system, called as IES (Indonesia Earthquake System, for cluster analysis, spatio temporal analysis, and visualize the multidimensional data of seismic parameters. We analyze the cluster analysis by using automatic clustering, that consists of get optimal number of cluster and Hierarchical K-means clustering. We explore the visual cluster and multidimensional data in low dimensional space visualization. We made experiment with observed data, that consists of seismic data around Indonesian archipelago during 2004 to 2014. Keywords: Clustering, visualization, multidimensional data, seismic parameters.
Multi-dimensional Fuzzy Euler Approximation
Directory of Open Access Journals (Sweden)
Yangyang Hao
2017-05-01
Full Text Available Multi-dimensional Fuzzy differential equations driven by multi-dimen-sional Liu process, have been intensively applied in many fields. However, we can not obtain the analytic solution of every multi-dimensional fuzzy differential equation. Then, it is necessary for us to discuss the numerical results in most situations. This paper focuses on the numerical method of multi-dimensional fuzzy differential equations. The multi-dimensional fuzzy Taylor expansion is given, based on this expansion, a numerical method which is designed for giving the solution of multi-dimensional fuzzy differential equation via multi-dimensional Euler method will be presented, and its local convergence also will be discussed.
Executive Information Systems' Multidimensional Models
Directory of Open Access Journals (Sweden)
2007-01-01
Full Text Available Executive Information Systems are design to improve the quality of strategic level of management in organization through a new type of technology and several techniques for extracting, transforming, processing, integrating and presenting data in such a way that the organizational knowledge filters can easily associate with this data and turn it into information for the organization. These technologies are known as Business Intelligence Tools. But in order to build analytic reports for Executive Information Systems (EIS in an organization we need to design a multidimensional model based on the business model from the organization. This paper presents some multidimensional models that can be used in EIS development and propose a new model that is suitable for strategic business requests.
Towards optimal packed string matching
DEFF Research Database (Denmark)
Ben-Kiki, Oren; Bille, Philip; Breslauer, Dany
2014-01-01
-size string-matching instruction wssm is available in contemporary commodity processors. The other word-size maximum-suffix instruction wslm is only required during the pattern pre-processing. Benchmarks show that our solution can be efficiently implemented, unlike some prior theoretical packed string...
Lagrangian multiforms and multidimensional consistency
Energy Technology Data Exchange (ETDEWEB)
Lobb, Sarah; Nijhoff, Frank [Department of Applied Mathematics, University of Leeds, Leeds LS2 9JT (United Kingdom)
2009-10-30
We show that well-chosen Lagrangians for a class of two-dimensional integrable lattice equations obey a closure relation when embedded in a higher dimensional lattice. On the basis of this property we formulate a Lagrangian description for such systems in terms of Lagrangian multiforms. We discuss the connection of this formalism with the notion of multidimensional consistency, and the role of the lattice from the point of view of the relevant variational principle.
Cuba: Multidimensional numerical integration library
Hahn, Thomas
2016-08-01
The Cuba library offers four independent routines for multidimensional numerical integration: Vegas, Suave, Divonne, and Cuhre. The four algorithms work by very different methods, and can integrate vector integrands and have very similar Fortran, C/C++, and Mathematica interfaces. Their invocation is very similar, making it easy to cross-check by substituting one method by another. For further safeguarding, the output is supplemented by a chi-square probability which quantifies the reliability of the error estimate.
Path integral approach to multidimensional quantum tunnelling
International Nuclear Information System (INIS)
Balantekin, A.B.; Takigawa, N.
1985-01-01
Path integral formulation of the coupled channel problem in the case of multidimensional quantum tunneling is presented and two-time influence functionals are introduced. The two-time influence functionals are calculated explicitly for the three simplest cases: Harmonic oscillators linearly or quadratically coupled to the translational motion and a system with finite number of equidistant energy levels linearly coupled to the translational motion. The effects of these couplings on the transmission probability are studied for two limiting cases, adiabatic case and when the internal system has a degenerate energy spectrum. The condition for the transmission probability to show a resonant structure is discussed and exemplified. Finally, the properties of the dissipation factor in the adiabatic limit and its correlation with the friction coefficient in the classically accessible region are studied
Security Contents: Politico-Military or Multidimensional?
Directory of Open Access Journals (Sweden)
Pere Vilanova
1997-12-01
Full Text Available The description of security problems has dramatically changed since the end of the bipolar system, and there are difficulties in building new concepts to comprehend a new and not yet defined international system. In the bipolar world, based on the North-South and East-West axes, security was described as systemic stability built upon deterrence and the defense of the statu quo. After the end of the Cold War, a new concept of multidimensional security was formulated. It lay emphasis on political, social (economic development andinternational (peaceful international relations democracy and the rule of law, putting aside too rapidly the military dimension. Vilanova argues that what have been identified as sources of new threats –narcotrafficking, ecology, migration, terrorism and fundamentalism– are not really new. There is a need to formulate political responses to these risks factors by means of public policies and intergovernmental and supranational action.
Critical-like features of stress response in frictional packings
International Nuclear Information System (INIS)
Cakir, Abdullah; Silbert, Leonardo E
2015-01-01
The mechanical response of static, unconfined, overcompressed face centred cubic, granular arrays is studied using large-scale, discrete element method simulations. Specifically, the stress response due to the application of a localised force perturbation—the Green function technique—is obtained in granular packings generated over several orders of magnitude in both the particle friction coefficient and the applied forcing. We observe crossover behaviour in the mechanical state of the system characterised by the changing nature of the resulting stress response. The transition between anisotropic and isotropic stress response exhibits critical-like features through the identification of a diverging length scale that distinguishes the spatial extent of anisotropic regions from those that display isotropic behaviour. A multidimensional phase diagram is constructed that parameterises the response of the system due to changing friction and force perturbations. (paper)
Improvement for the design of packed moving bed adsorption column
International Nuclear Information System (INIS)
Xiao Wei
2014-01-01
The problems needed to pay attention to in the physical design of packed moving bed adsorption column were presented. The design of key parts such as the inlet and outlet of liquid phase and gas phase were improved. The expected effect was achieved by the improvement. (author)
Modified strip packing heuristics for the rectangular variable-sized ...
African Journals Online (AJOL)
Frank G Ortmann
objects. Therefore, the packing of items into a bin may be considered as “cutting” away ... not be rotated (the oriented problem, hence the abbreviation “O”) and in ...... [32] Gilmore PC & Gomory RE, 1961, A linear programming approach to the ...
Viscoelastic gravel-pack carrier fluid
International Nuclear Information System (INIS)
Nehmer, W.L.
1988-01-01
The ability of a fluid to flow adequately into the formation during gravel-pack treatments is critical to achieving a good pack. Recent studies have indicated ''fish-eyes'' and/or ''microgels'' present in many polymer gelled carrier fluids will plug pore throats, leading to impaired leakoff and causing formation damage. Intensive manipulation of the polymer gelled fluid using shear and filter devices will help remove the particles, but it adds to the cost of the treatment in terms of equipment and manpower. Excessive shear will degrade the polymer leading to poor gravel suspension, while too little shear will cause filtration problems. A gelled carried fluid using a viscoelastic surfactant system has been found to leak off very efficiently to the formation, and cause no formation damage, without the use of shear/filter devices. Viscoelastic surfactant-base gelled fluids develop viscosity because of the association of surfactant moloecules into large rod-shaped aggregates. There is no hydration of polymer involved, so fish-eyes and microgels will not be formed in the viscoelastic fluid. A surfactant-base system having a yield point allows the gravel carrying properties to be much better than fluids gelled with conventional polymer systems (hydroxyethylcellulose [HEC]). For example, a gravel carried fluid gelled with 80 lb HEC/1,000 gal has a viscosity of about 400 cp at 170 sec/sup -1/; a viscoelastic surfactant-base system having only one-half the viscosity still flows into cores about four times more efficiently than the HEC-base fluid. The rheology, leakoff, formation damage and mixing properties of a viscoelastic, surfactant-base, gravel-pack carrier fluid are discussed
Valve packing manual. A maintenance application guide
International Nuclear Information System (INIS)
Aikin, J.A.; McCutcheon, R.G.; Cumming, D.
1997-01-01
Since 1970, AECL Chalk River Mechanical Equipment Development (MED) branch has invested over 175 person years in testing related to improving valve packing performance. Successful developments, including, 'live-loading', reduced packing heights, and performance-based packing qualification testing have been implemented. Since 1986, MED and the Integrated Valve Actuator Program Task Force - Valve Packing Steering Committee (IVAP-VPSC) have been involved in the development of combination die-formed graphite packing for use in CANDU plants. Many reports, articles, and specifications have been issued. Due to the large amount of test data and reports, a more user-friendly document has been prepared for everyday use. The Valve Packing Manual is based on many years of MED research and testing, as well as operating experience from CANDU nuclear generating stations (NGS). Since 1986, packing research and testing has been funded by the CANDU Owners Group (COG), the Electric Power Research Institute (EPRI), and participating valve packing manufacturers. The Valve Packing Manual (VPM) provides topical summaries of all work related to valve packing done since 1985. It includes advances in configuration design, stem packing friction, materials specifications, and installation procedures. This paper provides an overview on the application of the VPM with a focus on qualification testing, packing configuration, and stem packing friction. (author)
Energy Technology Data Exchange (ETDEWEB)
Hadley, O.L.; Corrigan, C.E.; Kirchstetter, T.W.; Cliff, S.S.; Ramanathan, V.
2010-01-12
Modeling studies show that the darkening of snow and ice by black carbon deposition is a major factor for the rapid disappearance of arctic sea ice, mountain glaciers and snow packs. This study provides one of the first direct measurements for the efficient removal of black carbon from the atmosphere by snow and its subsequent deposition to the snow packs of California. The early melting of the snow packs in the Sierras is one of the contributing factors to the severe water problems in California. BC concentrations in falling snow were measured at two mountain locations and in rain at a coastal site. All three stations reveal large BC concentrations in precipitation, ranging from 1.7 ng/g to 12.9 ng/g. The BC concentrations in the air after the snow fall were negligible suggesting an extremely efficient removal of BC by snow. The data suggest that below cloud scavenging, rather than ice nuclei, was the dominant source of BC in the snow. A five-year comparison of BC, dust, and total fine aerosol mass concentrations at multiple sites reveals that the measurements made at the sampling sites were representative of large scale deposition in the Sierra Nevada. The relative concentration of iron and calcium in the mountain aerosol indicates that one-quarter to one-third of the BC may have been transported from Asia.
Multidimensional Rank Reduction Estimator for Parametric MIMO Channel Models
Directory of Open Access Journals (Sweden)
Marius Pesavento
2004-08-01
Full Text Available A novel algebraic method for the simultaneous estimation of MIMO channel parameters from channel sounder measurements is developed. We consider a parametric multipath propagation model with P discrete paths where each path is characterized by its complex path gain, its directions of arrival and departure, time delay, and Doppler shift. This problem is treated as a special case of the multidimensional harmonic retrieval problem. While the well-known ESPRIT-type algorithms exploit shift-invariance between specific partitions of the signal matrix, the rank reduction estimator (RARE algorithm exploits their internal Vandermonde structure. A multidimensional extension of the RARE algorithm is developed, analyzed, and applied to measurement data recorded with the RUSK vector channel sounder in the 2 GHz band.
Nested element method in multidimensional neutron diffusion calculations
International Nuclear Information System (INIS)
Altiparmakov, D.V.
1983-01-01
A new numerical method is developed that is particularly efficient in solving the multidimensional neutron diffusion equation in geometrically complex systems. The needs for a generally applicable and fast running computer code have stimulated the inroad of a nonclassical (R-function) numerical method into the nuclear field. By using the R-functions, the geometrical components of the diffusion problem are a priori analytically implemented into the approximate solution. The class of functions, to which the approximate solution belongs, is chosen as close to the exact solution class as practically acceptable from the time consumption point of view. That implies a drastic reduction of the number of degrees of freedom, compared to the other methods. Furthermore, the reduced number of degrees of freedom enables calculation of large multidimensional problems on small computers
Packing Different Cuboids with Rotations and Spheres into a Cuboid
Directory of Open Access Journals (Sweden)
Y. G. Stoyan
2014-01-01
Full Text Available The paper considers a packing optimization problem of different spheres and cuboids into a cuboid of the minimal height. Translations and continuous rotations of cuboids are allowed. In the paper, we offer a way of construction of special functions (Φ-functions describing how rotations can be dealt with. These functions permit us to construct the mathematical model of the problem as a classical mathematical programming problem. Basic characteristics of the mathematical model are investigated. When solving the problem, the characteristics allow us to apply a number of original and state-of-the-art efficient methods of local and global optimization. Numerical examples of packing from 20 to 300 geometric objects are given.
Hypostatic jammed packings of frictionless nonspherical particles
VanderWerf, Kyle; Jin, Weiwei; Shattuck, Mark D.; O'Hern, Corey S.
2017-01-01
We perform computational studies of static packings of a variety of nonspherical particles including circulo-lines, circulo-polygons, ellipses, asymmetric dimers, and dumbbells to determine which shapes form hypostatic versus isostatic packings and to understand why hypostatic packings of nonspherical particles can be mechanically stable despite having fewer contacts than that predicted from na\\"ive constraint counting. To generate highly accurate force- and torque-balanced packings of circul...
1996-07-11
The Superior Court of New Jersey, Appellate Division, recognized "a physician's duty to warn those known to be at risk of avoidable harm from a genetically transmissible condition." During the 1950s, Dr. George Pack treated Donna Shafer's father for a cancerous blockage of the colon and multiple polyposis. In 1990, Safer was diagnosed with the same condition, which she claims is inherited, and, if not diagnosed and treated, invariably will lead to metastic colorectal cancer. Safer alleged that Dr. Pack knew the hereditary nature of the disease, yet failed to warn the immediate family, thus breaching his professional duty to warn. The court did not follow the analysis of the trial court, that a physician has no legal duty to warn the child of a patient of the genetic risk of disease because no physician and patient relationship exists between the doctor and the child.
Random packing of colloids and granular matter
Wouterse, A.
2008-01-01
This thesis deals with the random packing of colloids and granular matter. A random packing is a stable disordered collection of touching particles, without long-range positional and orientational order. Experimental random packings of particles with the same shape but made of different materials
Complications of balloon packing in epistaxis
Vermeeren, Lenka; Derks, Wynia; Fokkens, Wytske; Menger, Dirk Jan
2015-01-01
Although balloon packing appears to be efficient to control epistaxis, severe local complications can occur. We describe four patients with local lesions after balloon packing. Prolonged balloon packing can cause damage to nasal mucosa, septum and alar skin (nasal mucosa, the cartilaginous skeleton
Fully multidimensional flux-corrected transport algorithms for fluids
International Nuclear Information System (INIS)
Zalesak, S.T.
1979-01-01
The theory of flux-corrected transport (FCT) developed by Boris and Book is placed in a simple, generalized format, and a new algorithm for implementing the critical flux limiting stage in multidimensions without resort to time splitting is presented. The new flux limiting algorithm allows the use of FCT techniques in multidimensional fluid problems for which time splitting would produce unacceptable numerical results, such as those involving incompressible or nearly incompressible flow fields. The 'clipping' problem associated with the original one dimensional flux limiter is also eliminated or alleviated. Test results and applications to a two dimensional fluid plasma problem are presented
Analysis of self-similar solutions of multidimensional conservation laws
Energy Technology Data Exchange (ETDEWEB)
Keyfitz, Barbara Lee [The Ohio State Univ., Columbus, OH (United States)
2014-02-15
This project focused on analysis of multidimensional conservation laws, specifically on extensions to the study of self-siminar solutions, a project initiated by the PI. In addition, progress was made on an approach to studying conservation laws of very low regularity; in this research, the context was a novel problem in chromatography. Two graduate students in mathematics were supported during the grant period, and have almost completed their thesis research.
Measures for a multidimensional multiverse
Chung, Hyeyoun
2015-04-01
We explore the phenomenological implications of generalizing the causal patch and fat geodesic measures to a multidimensional multiverse, where the vacua can have differing numbers of large dimensions. We consider a simple model in which the vacua are nucleated from a D -dimensional parent spacetime through dynamical compactification of the extra dimensions, and compute the geometric contribution to the probability distribution of observations within the multiverse for each measure. We then study how the shape of this probability distribution depends on the time scales for the existence of observers, for vacuum domination, and for curvature domination (tobs,tΛ , and tc, respectively.) In this work we restrict ourselves to bubbles with positive cosmological constant, Λ . We find that in the case of the causal patch cutoff, when the bubble universes have p +1 large spatial dimensions with p ≥2 , the shape of the probability distribution is such that we obtain the coincidence of time scales tobs˜tΛ˜tc . Moreover, the size of the cosmological constant is related to the size of the landscape. However, the exact shape of the probability distribution is different in the case p =2 , compared to p ≥3 . In the case of the fat geodesic measure, the result is even more robust: the shape of the probability distribution is the same for all p ≥2 , and we once again obtain the coincidence tobs˜tΛ˜tc . These results require only very mild conditions on the prior probability of the distribution of vacua in the landscape. Our work shows that the observed double coincidence of time scales is a robust prediction even when the multiverse is generalized to be multidimensional; that this coincidence is not a consequence of our particular Universe being (3 +1 )-dimensional; and that this observable cannot be used to preferentially select one measure over another in a multidimensional multiverse.
Ordinal Comparison of Multidimensional Deprivation
DEFF Research Database (Denmark)
Sonne-Schmidt, Christoffer Scavenius; Tarp, Finn; Østerdal, Lars Peter
This paper develops an ordinal method of comparison of multidimensional inequality. In our model, population distribution g is more unequal than f when the distributions have common median and can be obtained from f by one or more shifts in population density that increase inequality. For our be...... benchmark 2x2 case (i.e. the case of two binary outcome variables), we derive an empirical method for making inequality comparisons. As an illustration, we apply the model to childhood poverty in Mozambique....
Decontamination of Chlorpyrifos packing using ionizing radiation: processing optimization
International Nuclear Information System (INIS)
Mori, Manoel Nunes; Sampa, Maria Helena de Oliveira; Duarte, Celina Lopes
2007-01-01
The discharge of empty plastic packing of pesticide can be an environmental concern causing problems to human health, animals and plants if done without inspection and monitoring. Among the commercial pesticides, chlorpyrifos, o, o- Diethyl - o- (3,5,6 - trichloro - 2 - pyridyl) phosphorothioate, has significant importance because of its wide distribution, extensive use and persistence. The most commonly used formulations include the emulsified concentrate, granule, wet powder and dispersible granule has significant importance because of its wide distribution and extensive use and persistence. The hydroxyl .OH attack is the most efficient process of chemical oxidation. The degradation-induced of chlorpyrifos by gamma radiolysis was studied in packaging of high-density polyethylene tree layer coextruded, named COEX, irradiated intact and fragments. The intact packing was irradiated with water and the fragmented packing was irradiated with water and with a solution of 50% of water and 50% of acetonitrile. An AECL 'Gammacell 2201 60 Co source and a multipurpose gamma irradiator were used in the processing. The chemical analysis of the chlorpyrifos and by-products were made using a gas chromatography associated to the mass spectrometry (MSGC-Shimadzu QP5000. Radiation processing of packing in pieces showed higher efficiency in removing chlorpyrifos than whole packing. The presence of water showed fundamental to promote the formation of frees radicals and acetonitrile facilitate the dissolution of chlorpyrifos and consequently its removal. (author)
Decontamination of Chlorpyrifos packing using ionizing radiation: processing optimization
Energy Technology Data Exchange (ETDEWEB)
Mori, Manoel Nunes; Sampa, Maria Helena de Oliveira; Duarte, Celina Lopes [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)]. E-mails: mnmori@ipen.br; mhosampa@ipen.br; clduarte@ipen.br
2007-07-01
The discharge of empty plastic packing of pesticide can be an environmental concern causing problems to human health, animals and plants if done without inspection and monitoring. Among the commercial pesticides, chlorpyrifos, o, o- Diethyl - o- (3,5,6 - trichloro - 2 - pyridyl) phosphorothioate, has significant importance because of its wide distribution, extensive use and persistence. The most commonly used formulations include the emulsified concentrate, granule, wet powder and dispersible granule has significant importance because of its wide distribution and extensive use and persistence. The hydroxyl .OH attack is the most efficient process of chemical oxidation. The degradation-induced of chlorpyrifos by gamma radiolysis was studied in packaging of high-density polyethylene tree layer coextruded, named COEX, irradiated intact and fragments. The intact packing was irradiated with water and the fragmented packing was irradiated with water and with a solution of 50% of water and 50% of acetonitrile. An AECL 'Gammacell 2201 {sup 60}Co source and a multipurpose gamma irradiator were used in the processing. The chemical analysis of the chlorpyrifos and by-products were made using a gas chromatography associated to the mass spectrometry (MSGC-Shimadzu QP5000. Radiation processing of packing in pieces showed higher efficiency in removing chlorpyrifos than whole packing. The presence of water showed fundamental to promote the formation of frees radicals and acetonitrile facilitate the dissolution of chlorpyrifos and consequently its removal. (author)
SPH Modelling of Sea-ice Pack Dynamics
Staroszczyk, Ryszard
2017-12-01
The paper is concerned with the problem of sea-ice pack motion and deformation under the action of wind and water currents. Differential equations describing the dynamics of ice, with its very distinct mateFfigrial responses in converging and diverging flows, express the mass and linear momentum balances on the horizontal plane (the free surface of the ocean). These equations are solved by the fully Lagrangian method of smoothed particle hydrodynamics (SPH). Assuming that the ice behaviour can be approximated by a non-linearly viscous rheology, the proposed SPH model has been used to simulate the evolution of a sea-ice pack driven by wind drag stresses. The results of numerical simulations illustrate the evolution of an ice pack, including variations in ice thickness and ice area fraction in space and time. The effects of different initial ice pack configurations and of different conditions assumed at the coast-ice interface are examined. In particular, the SPH model is applied to a pack flow driven by a vortex wind to demonstrate how well the Lagrangian formulation can capture large deformations and displacements of sea ice.
Schmüdgen, Konrad
2017-01-01
This advanced textbook provides a comprehensive and unified account of the moment problem. It covers the classical one-dimensional theory and its multidimensional generalization, including modern methods and recent developments. In both the one-dimensional and multidimensional cases, the full and truncated moment problems are carefully treated separately. Fundamental concepts, results and methods are developed in detail and accompanied by numerous examples and exercises. Particular attention is given to powerful modern techniques such as real algebraic geometry and Hilbert space operators. A wide range of important aspects are covered, including the Nevanlinna parametrization for indeterminate moment problems, canonical and principal measures for truncated moment problems, the interplay between Positivstellensätze and moment problems on semi-algebraic sets, the fibre theorem, multidimensional determinacy theory, operator-theoretic approaches, and the existence theory and important special topics of multidime...
Implementation of Bin Packing Model for Reed Switch Production Planning
Energy Technology Data Exchange (ETDEWEB)
Parra, Rainier Romero [Polytechnic University of Baja California, Calle de la Claridad S/N, Col Plutarco Elias Calles, Mexicali, B. C., 21376 (Mexico); Burtseva, Larysa [Engineering Institute, Autonomous University of Baja California, Calle de la Normal S/N, Col. Insurgentes Este, Mexicali, BC, 21280 (Mexico)
2010-06-17
This paper presents a form to resolve a real problem of efficient material election in reed switch manufacturing. The carrying out of the consumer demands depends on the stochastic results of the classification process where each lot of switches is distributed into bins according to an electric measure value. Various glass types are employed for the switch manufacturing. The effect caused by the glass type variation on the switch classification results was investigated. Based on real data statistic analysis, the problem is reduced to the lot number minimizing taking into consideration the glass type, and interpreted as a bin packing problem generalization. On difference to the classic bin packing problem, in the considered case, an item represents a set of pieces; a container is divided into a number of bins (sub-containers); the bin capacity is variable; there are the assignment restrictions between bins and sets of pieces; the items are allowed to be fragmented into bins and containers. The problem has a high complexity. A heuristic offline algorithm is proposed to find the quantity, types and packing sequence of containers, the item fragments associated with containers and bins. The bin capacities do not affect the algorithm.
Implementation of Bin Packing Model for Reed Switch Production Planning
International Nuclear Information System (INIS)
Parra, Rainier Romero; Burtseva, Larysa
2010-01-01
This paper presents a form to resolve a real problem of efficient material election in reed switch manufacturing. The carrying out of the consumer demands depends on the stochastic results of the classification process where each lot of switches is distributed into bins according to an electric measure value. Various glass types are employed for the switch manufacturing. The effect caused by the glass type variation on the switch classification results was investigated. Based on real data statistic analysis, the problem is reduced to the lot number minimizing taking into consideration the glass type, and interpreted as a bin packing problem generalization. On difference to the classic bin packing problem, in the considered case, an item represents a set of pieces; a container is divided into a number of bins (sub-containers); the bin capacity is variable; there are the assignment restrictions between bins and sets of pieces; the items are allowed to be fragmented into bins and containers. The problem has a high complexity. A heuristic offline algorithm is proposed to find the quantity, types and packing sequence of containers, the item fragments associated with containers and bins. The bin capacities do not affect the algorithm.
Multidimensional fatigue and its correlates in hospitalised advanced cancer patients.
Echteld, M.A.; Passchier, J.; Teunissen, S.; Claessen, S.; Wit, R. de; Rijt, C.C.D. van der
2007-01-01
Although fatigue is a multidimensional concept, multidimensional fatigue is rarely investigated in hospitalised cancer patients. We determined the levels and correlates of multidimensional fatigue in 100 advanced cancer patients admitted for symptom control. Fatigue dimensions were general fatigue
SUSTAINABLE DEVELOPMENT, A MULTIDIMENSIONAL CONCEPT
Directory of Open Access Journals (Sweden)
TEODORESCU ANA MARIA
2015-06-01
Full Text Available Sustainable development imposed itself as a corollary of economic term "development". Sustainable development is meant to be the summation of economic, environmental and social considerations for the present and especially for the future. The concept of sustainable development plays an important role in european and global meetings since 1972, the year it has been set for the first time. Strategies necessary to achieve the objectives of sustainable development have been developed, indicators meant to indicate the result of the implementation of policies have been created, national plans were oriented towards achieving the proposed targets. I wanted to highlight the multidimensional character of the concept of sustainable development. Thus, using specialized national and international literature, I have revealed different approaches of one pillar to the detriment of another pillar depending on the specific field. In the different concepts of sustainable development, the consensus is undoubtedly agreed on its components: economic, social, environmental. Based on this fact, the concept of sustainability has different connotations depending on the specific content of each discipline: biology, economics, sociology, environmental ethics. The multidimensional valence of sustainable development consists of three pillars ability to act together for the benefit of present and future generations. Being a multidimensional concept, importance attached to a pillar over another is directed according to the particularities of each field: in economy profit prevails, in ecology care of natural resources is the most important, the social aims improving human living conditions. The challenge of sustainable development is to combine all the economic, environmental and social benefits and the present generation to come. Ecological approach is reflected in acceptance of limited natural resources by preserving natural capital. In terms of the importance of
Automated packing systems: review of industrial implementations
Whelan, Paul F.; Batchelor, Bruce G.
1993-08-01
A rich theoretical background to the problems that occur in the automation of material handling can be found in operations research, production engineering, systems engineering and automation, more specifically machine vision, literature. This work has contributed towards the design of intelligent handling systems. This paper will review the application of these automated material handling and packing techniques to industrial problems. The discussion will also highlight the systems integration issues involved in these applications. An outline of one such industrial application, the automated placement of shape templates on to leather hides, is also discussed. The purpose of this system is to arrange shape templates on a leather hide in an efficient manner, so as to minimize the leather waste, before they are automatically cut from the hide. These pieces are used in the furniture and car manufacturing industries for the upholstery of high quality leather chairs and car seats. Currently this type of operation is semi-automated. The paper will outline the problems involved in the full automation of such a procedure.
Hypostatic jammed packings of frictionless nonspherical particles
VanderWerf, Kyle; Jin, Weiwei; Shattuck, Mark D.; O'Hern, Corey S.
2018-01-01
We perform computational studies of static packings of a variety of nonspherical particles including circulo-lines, circulo-polygons, ellipses, asymmetric dimers, dumbbells, and others to determine which shapes form packings with fewer contacts than degrees of freedom (hypostatic packings) and which have equal numbers of contacts and degrees of freedom (isostatic packings), and to understand why hypostatic packings of nonspherical particles can be mechanically stable despite having fewer contacts than that predicted from naive constraint counting. To generate highly accurate force- and torque-balanced packings of circulo-lines and cir-polygons, we developed an interparticle potential that gives continuous forces and torques as a function of the particle coordinates. We show that the packing fraction and coordination number at jamming onset obey a masterlike form for all of the nonspherical particle packings we studied when plotted versus the particle asphericity A , which is proportional to the ratio of the squared perimeter to the area of the particle. Further, the eigenvalue spectra of the dynamical matrix for packings of different particle shapes collapse when plotted at the same A . For hypostatic packings of nonspherical particles, we verify that the number of "quartic" modes along which the potential energy increases as the fourth power of the perturbation amplitude matches the number of missing contacts relative to the isostatic value. We show that the fourth derivatives of the total potential energy in the directions of the quartic modes remain nonzero as the pressure of the packings is decreased to zero. In addition, we calculate the principal curvatures of the inequality constraints for each contact in circulo-line packings and identify specific types of contacts with inequality constraints that possess convex curvature. These contacts can constrain multiple degrees of freedom and allow hypostatic packings of nonspherical particles to be mechanically
The West Haven-Yale Multidimensional Pain Inventory (WHYMPI).
Kerns, R D; Turk, D C; Rudy, T E
1985-12-01
The complexity of chronic pain has represented a major dilemma for clinical researchers interested in the reliable and valid assessment of the problem and the evaluation of treatment approaches. The West Haven-Yale Multidimensional Pain Inventory (WHYMPI) was developed in order to fill a widely recognized void in the assessment of clinical pain. Assets of the inventory are its brevity and clarity, its foundation in contemporary psychological theory, its multidimensional focus, and its strong psychometric properties. Three parts of the inventory, comprised of 12 scales, examine the impact of pain on the patients' lives, the responses of others to the patients' communications of pain, and the extent to which patients participate in common daily activities. The instrument is recommended for use in conjunction with behavioral and psychophysiological assessment strategies in the evaluation of chronic pain patients in clinical settings. The utility of the WHYMPI in empirical investigations of chronic pain is also discussed.
Applied multidimensional scaling and unfolding
Borg, Ingwer; Mair, Patrick
2018-01-01
This book introduces multidimensional scaling (MDS) and unfolding as data analysis techniques for applied researchers. MDS is used for the analysis of proximity data on a set of objects, representing the data as distances between points in a geometric space (usually of two dimensions). Unfolding is a related method that maps preference data (typically evaluative ratings of different persons on a set of objects) as distances between two sets of points (representing the persons and the objects, resp.). This second edition has been completely revised to reflect new developments and the coverage of unfolding has also been substantially expanded. Intended for applied researchers whose main interests are in using these methods as tools for building substantive theories, it discusses numerous applications (classical and recent), highlights practical issues (such as evaluating model fit), presents ways to enforce theoretical expectations for the scaling solutions, and addresses the typical mistakes that MDS/unfoldin...
CERN Bulletin
2011-01-01
The Particle Zoo is a colourful set of hand-made soft toys representing the particles in the Standard Model and beyond. It includes a “theoreticals” pack where you can find yet undiscovered particles: the best-selling Higgs boson, the graviton, the tachyon, and dark matter. Supersymmetric particle soft toys are also available on demand. But what would happen to the zoo if Nature had prepared some unexpected surprises? Julie Peasley, the zookeeper, is ready to sew new smiling faces… The "Theoreticals" pack in the Particle Zoo. There is only one place in the world where you can buy a smiling Higgs boson and it’s not at CERN, although this is where scientists hope to observe it. The blue star-shaped particle is the best seller of Julie Peasley’s Particle Zoo – a collection of tens of soft toys representing all sorts of particles, including composite and decaying particles. Over the years Julie’s zoo ...
Multidimensional particle swarm optimization for machine learning and pattern recognition
Kiranyaz, Serkan; Gabbouj, Moncef
2013-01-01
For many engineering problems we require optimization processes with dynamic adaptation as we aim to establish the dimension of the search space where the optimum solution resides and develop robust techniques to avoid the local optima usually associated with multimodal problems. This book explores multidimensional particle swarm optimization, a technique developed by the authors that addresses these requirements in a well-defined algorithmic approach. After an introduction to the key optimization techniques, the authors introduce their unified framework and demonstrate its advantages in chal
Minimal models of multidimensional computations.
Directory of Open Access Journals (Sweden)
Jeffrey D Fitzgerald
2011-03-01
Full Text Available The multidimensional computations performed by many biological systems are often characterized with limited information about the correlations between inputs and outputs. Given this limitation, our approach is to construct the maximum noise entropy response function of the system, leading to a closed-form and minimally biased model consistent with a given set of constraints on the input/output moments; the result is equivalent to conditional random field models from machine learning. For systems with binary outputs, such as neurons encoding sensory stimuli, the maximum noise entropy models are logistic functions whose arguments depend on the constraints. A constraint on the average output turns the binary maximum noise entropy models into minimum mutual information models, allowing for the calculation of the information content of the constraints and an information theoretic characterization of the system's computations. We use this approach to analyze the nonlinear input/output functions in macaque retina and thalamus; although these systems have been previously shown to be responsive to two input dimensions, the functional form of the response function in this reduced space had not been unambiguously identified. A second order model based on the logistic function is found to be both necessary and sufficient to accurately describe the neural responses to naturalistic stimuli, accounting for an average of 93% of the mutual information with a small number of parameters. Thus, despite the fact that the stimulus is highly non-Gaussian, the vast majority of the information in the neural responses is related to first and second order correlations. Our results suggest a principled and unbiased way to model multidimensional computations and determine the statistics of the inputs that are being encoded in the outputs.
Energy Technology Data Exchange (ETDEWEB)
Pages, A [Centre d' Etudes Nucleaires de Saclay (France)
1962-04-15
Experimenters are making increasingly frequent use of analysis units by which a function of several parameters can be obtained (the number of parameters and the relative precision of each of them being variable from experiment to experiment). Present-day analysers are poorly suited to the steadily growing complexity of experiments. There are several reasons for this: the number of possible parameters is far too small (unblocking only on 100-channel and 256-channel analysers) as is also their capacity; this limitation considerably increases the accelerator time; sometimes the poor ''yield'' of these analysers makes the experiment impossible; moreover, being designed in a single ''block'', they are lacking in flexibility for use. During 1958-59 a multi-dimensional apparatus limited to 2 paths of 63 channels was studied and built. The various essential functions are separated: analysis, transfer (multi-dimensional operation), utilization of results. At the SEG, Messrs. Amram, Guillon and Thenard are designing and building a multidimensional analyser, 1023 channels by 63 channels (for the neutron velocity measurement group of the SPNBE). In order to deal with the above-mentioned limitations, the electronics laboratory of the SPNBE is also developing a functional multi-dimensional analyser, in which the transfer function itself has been broken down into units (interrupter, non-integrator memory, conditioner and computer). Like the limits defining the paths, the types of units selected vary in accordance with the requirements and complexity of the experiment (standard interfunctional language). (author) [French] Les experimentateurs utilisent de plus en plus frequemment des ensembles d'analyse permettant d'obtenir une fonction de plusieurs parametres (le nombre de parametres pouvant varier d'une experience a l'autre ainsi que la precision relative de chacun de ceux-ci). Les analyseurs actuels se pretent mal a la complexite toujours croissante des experiences et ceci pour
Structured packing: an opportunity for energy savings
International Nuclear Information System (INIS)
Chavez T, R.H.; Guadarrama G, J.J.
1996-01-01
This work emphasizes the advantages about the use of structured packing. This type of packings allows by its geometry to reduce the processing time giving energy savings and throw down the production costs in several industries such as heavy water production plants, petrochemical industry and all industries involved with separation processes. There is a comparative results of energy consumption utilizing the structured vs. Raschig packings. (Author)
THE INTEGRATED LAYOUT DECISIONS FOR AUTOMATIC CONTROL OF PACKING SYSTEMS
Directory of Open Access Journals (Sweden)
A. Volodin
2017-06-01
Full Text Available On many industrial objects regulators of pressure are used. Following initial data are necessary for proper selection of a regulator and calculation of throughput: a working environment, entrance and target pressure, expense, temperature of a working environment, accuracy of regulation, a class of tightness, diameter of the pipeline, type of accession, constructional materials, external or internal registration of target pressure, protection against excess of pressure.The decision of this problem is closely connected with the proved choice of types of the process equipment, wide automation of technological processes, introduction of new technical decisions, use of necessary means of the control over realization of problems of complex mechanization of technological operations. In article the analysis of work of the functional module of a vertical multiline automatic packing machine on the basis of a proportional regulator of pressure «CAMOZZI» with realization of a feedback by means of an analog signal of regulator МХ-PRO [1-3] is lead. The drive of the holder for a rolled material has been tested on proportional management of position of the directing rollers used on a technological site of supply and regulation of a tension of a tape of a roll of a packing material at formation of packing.Results on use as the operating module of regulator МХ-PRO for management of a drive of the holder for a roll of a material in view of a course and pressure in a pneumatic system are received. Carried out researches provide the way to raise operational properties of a transportation system of supply of a packing material for technological processes of packing modules at the food enterprises.
Numerical Simulation on Dense Packing of Granular Materials by Container Oscillation
Directory of Open Access Journals (Sweden)
Jun Liu
2013-01-01
Full Text Available The packing of granular materials is a basic and important problem in geomechanics. An approach, which generates dense packing of spheres confined in cylindrical and cuboidal containers in three steps, is introduced in this work. A loose packing structure is first generated by means of a reference lattice method. Then a dense packing structure is obtained in a container by simulating dropping of particles under gravitational forces. Furthermore, a scheme that makes the bottom boundary fluctuate up and down was applied to obtain more denser packing. The discrete element method (DEM was employed to simulate the interactions between particle-particle and particle-boundary during the particles' motions. Finally, two cases were presented to indicate the validity of the method proposed in this work.
Multidimensional singular integrals and integral equations
Mikhlin, Solomon Grigorievich; Stark, M; Ulam, S
1965-01-01
Multidimensional Singular Integrals and Integral Equations presents the results of the theory of multidimensional singular integrals and of equations containing such integrals. Emphasis is on singular integrals taken over Euclidean space or in the closed manifold of Liapounov and equations containing such integrals. This volume is comprised of eight chapters and begins with an overview of some theorems on linear equations in Banach spaces, followed by a discussion on the simplest properties of multidimensional singular integrals. Subsequent chapters deal with compounding of singular integrals
International Nuclear Information System (INIS)
Lawrence, R.D.; Dorning, J.J.
1980-01-01
A coarse-mesh discrete nodal integral transport theory method has been developed for the efficient numerical solution of multidimensional transport problems of interest in reactor physics and shielding applications. The method, which is the discrete transport theory analogue and logical extension of the nodal Green's function method previously developed for multidimensional neutron diffusion problems, utilizes the same transverse integration procedure to reduce the multidimensional equations to coupled one-dimensional equations. This is followed by the conversion of the differential equations to local, one-dimensional, in-node integral equations by integrating back along neutron flight paths. One-dimensional and two-dimensional transport theory test problems have been systematically studied to verify the superior computational efficiency of the new method
Statistical segmentation of multidimensional brain datasets
Desco, Manuel; Gispert, Juan D.; Reig, Santiago; Santos, Andres; Pascau, Javier; Malpica, Norberto; Garcia-Barreno, Pedro
2001-07-01
This paper presents an automatic segmentation procedure for MRI neuroimages that overcomes part of the problems involved in multidimensional clustering techniques like partial volume effects (PVE), processing speed and difficulty of incorporating a priori knowledge. The method is a three-stage procedure: 1) Exclusion of background and skull voxels using threshold-based region growing techniques with fully automated seed selection. 2) Expectation Maximization algorithms are used to estimate the probability density function (PDF) of the remaining pixels, which are assumed to be mixtures of gaussians. These pixels can then be classified into cerebrospinal fluid (CSF), white matter and grey matter. Using this procedure, our method takes advantage of using the full covariance matrix (instead of the diagonal) for the joint PDF estimation. On the other hand, logistic discrimination techniques are more robust against violation of multi-gaussian assumptions. 3) A priori knowledge is added using Markov Random Field techniques. The algorithm has been tested with a dataset of 30 brain MRI studies (co-registered T1 and T2 MRI). Our method was compared with clustering techniques and with template-based statistical segmentation, using manual segmentation as a gold-standard. Our results were more robust and closer to the gold-standard.
Imaging of body packing: errors and medico-legal issues.
Reginelli, Alfonso; Russo, Anna; Urraro, Fabrizio; Maresca, Duilia; Martiniello, Ciro; D'Andrea, Alfredo; Brunese, Luca; Pinto, Antonio
2015-10-01
Body packing is the ingestion or insertion in the human body of packed illicit substances. Over the last 20 years, drug smuggling has increased global and new means of transport of narcotics have emerged. Among these, the most frequent one is the gastrointestinal tract: from mouth to anus, vagina, and ears. Cocaine is one of the most traded drugs, followed by heroin. Condoms, latex gloves, and balloons are typically used as drug packets for retention in the body. There are different radiologic modalities to detect illicit drugs in body packing: Plain radiography, computed tomography (CT), ultrasound, and magnetic resonance. Current protocols recommend the use of radiography to confirm packet retention and, in case of doubt, the use of abdominal CT scan with reduced mAs. In case of packet rupture, catastrophic effects can occur. Management of patients carrying packets of drugs is a recurrent medico-legal problem. To improve diagnostic accuracy and prevent hazardous complications, radiologists and emergency physicians should be familiar with radiologic features of body packing. The radiologist plays both a social and a medico-legal role in their assessment, and it should not be limited only to the identification of the packages but must also provide accurate information about their number and their exact location. In this review, we focus on diagnostic errors and medico-legal issues related to the radiological assessment of body packers.
Multidimensionally encoded magnetic resonance imaging.
Lin, Fa-Hsuan
2013-07-01
Magnetic resonance imaging (MRI) typically achieves spatial encoding by measuring the projection of a q-dimensional object over q-dimensional spatial bases created by linear spatial encoding magnetic fields (SEMs). Recently, imaging strategies using nonlinear SEMs have demonstrated potential advantages for reconstructing images with higher spatiotemporal resolution and reducing peripheral nerve stimulation. In practice, nonlinear SEMs and linear SEMs can be used jointly to further improve the image reconstruction performance. Here, we propose the multidimensionally encoded (MDE) MRI to map a q-dimensional object onto a p-dimensional encoding space where p > q. MDE MRI is a theoretical framework linking imaging strategies using linear and nonlinear SEMs. Using a system of eight surface SEM coils with an eight-channel radiofrequency coil array, we demonstrate the five-dimensional MDE MRI for a two-dimensional object as a further generalization of PatLoc imaging and O-space imaging. We also present a method of optimizing spatial bases in MDE MRI. Results show that MDE MRI with a higher dimensional encoding space can reconstruct images more efficiently and with a smaller reconstruction error when the k-space sampling distribution and the number of samples are controlled. Copyright © 2012 Wiley Periodicals, Inc.
Discovering Multidimensional Structure in Relational Data
DEFF Research Database (Denmark)
Jensen, Mikael Rune; Holmgren, Thomas; Pedersen, Torben Bach
2004-01-01
On-Line Analytical Processing (OLAP) systems based on multidimensional databases are essential elements of decision support. However, most existing data is stored in ordinary relational OLTP databases, i.e., data has to be (re-) modeled as multidimensional cubes before the advantages of OLAP to...... algorithms for discovering multidimensional schemas from relational databases. The algorithms take a wide range of available metadata into account in the discovery process, including functional and inclusion dependencies, and key and cardinality information....... tools are available. In this paper we present an approach for the automatic construction of multidimensional OLAP database schemas from existing relational OLTP databases, enabling easy OLAP design and analysis for most existing data sources. This is achieved through a set of practical and effective...
Two multi-dimensional uncertainty relations
International Nuclear Information System (INIS)
Skala, L; Kapsa, V
2008-01-01
Two multi-dimensional uncertainty relations, one related to the probability density and the other one related to the probability density current, are derived and discussed. Both relations are stronger than the usual uncertainty relations for the coordinates and momentum
Multidimensional artificial field embedding with spatial sensitivity
CSIR Research Space (South Africa)
Lunga, D
2013-06-01
Full Text Available Multidimensional embedding is a technique useful for characterizing spectral signature relations in hyperspectral images. However, such images consist of disjoint similar spectral classes that are spatially sensitive, thus presenting challenges...
CAMS: OLAPing Multidimensional Data Streams Efficiently
Cuzzocrea, Alfredo
In the context of data stream research, taming the multidimensionality of real-life data streams in order to efficiently support OLAP analysis/mining tasks is a critical challenge. Inspired by this fundamental motivation, in this paper we introduce CAMS (C ube-based A cquisition model for M ultidimensional S treams), a model for efficiently OLAPing multidimensional data streams. CAMS combines a set of data stream processing methodologies, namely (i) the OLAP dimension flattening process, which allows us to obtain dimensionality reduction of multidimensional data streams, and (ii) the OLAP stream aggregation scheme, which aggregates data stream readings according to an OLAP-hierarchy-based membership approach. We complete our analytical contribution by means of experimental assessment and analysis of both the efficiency and the scalability of OLAPing capabilities of CAMS on synthetic multidimensional data streams. Both analytical and experimental results clearly connote CAMS as an enabling component for next-generation Data Stream Management Systems.
The general packed column : an analytical solution
Gielen, J.L.W.
2000-01-01
The transient behaviour of a packed column is considered. The column, uniformly packed on a macroscopic scale, is multi-structured on the microscopic level: the solid phase consists of particles, which may differ in incidence, shape or size, and other relevant physical properties. Transport in the
On contact numbers in random rod packings
Wouterse, A.; Luding, Stefan; Philipse, A.P.
2009-01-01
Random packings of non-spherical granular particles are simulated by combining mechanical contraction and molecular dynamics, to determine contact numbers as a function of density. Particle shapes are varied from spheres to thin rods. The observed contact numbers (and packing densities) agree well
2010-01-01
... according to size, internal quality, and external appearance and condition of hazelnuts packed in accordance... 7 Agriculture 8 2010-01-01 2010-01-01 false Pack. 982.11 Section 982.11 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and...
Multidimensional Poverty and Child Survival in India
Mohanty, Sanjay K.
2011-01-01
Background Though the concept of multidimensional poverty has been acknowledged cutting across the disciplines (among economists, public health professionals, development thinkers, social scientists, policy makers and international organizations) and included in the development agenda, its measurement and application are still limited. Objectives and Methodology Using unit data from the National Family and Health Survey 3, India, this paper measures poverty in multidimensional space and examine the linkages of multidimensional poverty with child survival. The multidimensional poverty is measured in the dimension of knowledge, health and wealth and the child survival is measured with respect to infant mortality and under-five mortality. Descriptive statistics, principal component analyses and the life table methods are used in the analyses. Results The estimates of multidimensional poverty are robust and the inter-state differentials are large. While infant mortality rate and under-five mortality rate are disproportionately higher among the abject poor compared to the non-poor, there are no significant differences in child survival among educationally, economically and health poor at the national level. State pattern in child survival among the education, economical and health poor are mixed. Conclusion Use of multidimensional poverty measures help to identify abject poor who are unlikely to come out of poverty trap. The child survival is significantly lower among abject poor compared to moderate poor and non-poor. We urge to popularize the concept of multiple deprivations in research and program so as to reduce poverty and inequality in the population. PMID:22046384
Multidimensional poverty and child survival in India.
Mohanty, Sanjay K
2011-01-01
Though the concept of multidimensional poverty has been acknowledged cutting across the disciplines (among economists, public health professionals, development thinkers, social scientists, policy makers and international organizations) and included in the development agenda, its measurement and application are still limited. OBJECTIVES AND METHODOLOGY: Using unit data from the National Family and Health Survey 3, India, this paper measures poverty in multidimensional space and examine the linkages of multidimensional poverty with child survival. The multidimensional poverty is measured in the dimension of knowledge, health and wealth and the child survival is measured with respect to infant mortality and under-five mortality. Descriptive statistics, principal component analyses and the life table methods are used in the analyses. The estimates of multidimensional poverty are robust and the inter-state differentials are large. While infant mortality rate and under-five mortality rate are disproportionately higher among the abject poor compared to the non-poor, there are no significant differences in child survival among educationally, economically and health poor at the national level. State pattern in child survival among the education, economical and health poor are mixed. Use of multidimensional poverty measures help to identify abject poor who are unlikely to come out of poverty trap. The child survival is significantly lower among abject poor compared to moderate poor and non-poor. We urge to popularize the concept of multiple deprivations in research and program so as to reduce poverty and inequality in the population.
Multidimensional poverty and child survival in India.
Directory of Open Access Journals (Sweden)
Sanjay K Mohanty
Full Text Available Though the concept of multidimensional poverty has been acknowledged cutting across the disciplines (among economists, public health professionals, development thinkers, social scientists, policy makers and international organizations and included in the development agenda, its measurement and application are still limited. OBJECTIVES AND METHODOLOGY: Using unit data from the National Family and Health Survey 3, India, this paper measures poverty in multidimensional space and examine the linkages of multidimensional poverty with child survival. The multidimensional poverty is measured in the dimension of knowledge, health and wealth and the child survival is measured with respect to infant mortality and under-five mortality. Descriptive statistics, principal component analyses and the life table methods are used in the analyses.The estimates of multidimensional poverty are robust and the inter-state differentials are large. While infant mortality rate and under-five mortality rate are disproportionately higher among the abject poor compared to the non-poor, there are no significant differences in child survival among educationally, economically and health poor at the national level. State pattern in child survival among the education, economical and health poor are mixed.Use of multidimensional poverty measures help to identify abject poor who are unlikely to come out of poverty trap. The child survival is significantly lower among abject poor compared to moderate poor and non-poor. We urge to popularize the concept of multiple deprivations in research and program so as to reduce poverty and inequality in the population.
Condensation in Nanoporous Packed Beds.
Ally, Javed; Molla, Shahnawaz; Mostowfi, Farshid
2016-05-10
In materials with tiny, nanometer-scale pores, liquid condensation is shifted from the bulk saturation pressure observed at larger scales. This effect is called capillary condensation and can block pores, which has major consequences in hydrocarbon production, as well as in fuel cells, catalysis, and powder adhesion. In this study, high pressure nanofluidic condensation studies are performed using propane and carbon dioxide in a colloidal crystal packed bed. Direct visualization allows the extent of condensation to be observed, as well as inference of the pore geometry from Bragg diffraction. We show experimentally that capillary condensation depends on pore geometry and wettability because these factors determine the shape of the menisci that coalesce when pore filling occurs, contrary to the typical assumption that all pore structures can be modeled as cylindrical and perfectly wetting. We also observe capillary condensation at higher pressures than has been done previously, which is important because many applications involving this phenomenon occur well above atmospheric pressure, and there is little, if any, experimental validation of capillary condensation at such pressures, particularly with direct visualization.
Hawking Colloquium Packed CERN Auditoriums
2006-01-01
Stephen Hawking's week long visit to CERN included an 'exceptional CERN colloquium' which filled six auditoriums. Stephen Hawking during his visit to the ATLAS experiment. Stephen Hawking, Lucasian Professor of Cambridge University, visited the Theory Unit of the Physics Department from 24 September to 1 October 2006. As part of his visit, he gave two lectures in the main auditorium - a theoretical seminar on 'The Semi-Classical Birth of The Universe', attended by about 120 specialists; and a colloquium titled 'The Origin of The Universe'. As a key public figure in theoretical physics, his presence was eagerly awaited on both occasions. Those who wanted to attend the colloquium had to arrive early and be equipped with plenty of patience. An hour before it was due to begin, the 400 capacity of the main auditorium was already full. The lecture, simultaneously broadcast to five other fully packed CERN auditoriums, was attended by an estimated total of 850. Stephen Hawking attracted a large CERN crowd, filling ...
Improved multidimensional semiclassical tunneling theory.
Wagner, Albert F
2013-12-12
We show that the analytic multidimensional semiclassical tunneling formula of Miller et al. [Miller, W. H.; Hernandez, R.; Handy, N. C.; Jayatilaka, D.; Willets, A. Chem. Phys. Lett. 1990, 172, 62] is qualitatively incorrect for deep tunneling at energies well below the top of the barrier. The origin of this deficiency is that the formula uses an effective barrier weakly related to the true energetics but correctly adjusted to reproduce the harmonic description and anharmonic corrections of the reaction path at the saddle point as determined by second order vibrational perturbation theory. We present an analytic improved semiclassical formula that correctly includes energetic information and allows a qualitatively correct representation of deep tunneling. This is done by constructing a three segment composite Eckart potential that is continuous everywhere in both value and derivative. This composite potential has an analytic barrier penetration integral from which the semiclassical action can be derived and then used to define the semiclassical tunneling probability. The middle segment of the composite potential by itself is superior to the original formula of Miller et al. because it incorporates the asymmetry of the reaction barrier produced by the known reaction exoergicity. Comparison of the semiclassical and exact quantum tunneling probability for the pure Eckart potential suggests a simple threshold multiplicative factor to the improved formula to account for quantum effects very near threshold not represented by semiclassical theory. The deep tunneling limitations of the original formula are echoed in semiclassical high-energy descriptions of bound vibrational states perpendicular to the reaction path at the saddle point. However, typically ab initio energetic information is not available to correct it. The Supporting Information contains a Fortran code, test input, and test output that implements the improved semiclassical tunneling formula.
On the measurement of the (multidimensional) inequality of health distributions
DEFF Research Database (Denmark)
Hougaard, Jens Leth; Moreno-Ternero, Juan D.; Østerdal, Lars Peter Raahave
2013-01-01
a standard mathematical structure. We single out two families of (absolute and relative) multidimensional health inequality indices, inspired by the classical normative approach to income inequality measurement. We also discuss how to extend the analysis to deal with the related problem of health deprivation......Health outcomes are often described according to two dimensions: quality of life and quantity of life. We analyze the measurement of inequality of health distributions referring to these two dimensions. Our analysis relies on a novel treatment of the quality-of-life dimension, which might not have...
A multidimensional continued fraction and some of its statistical properties
International Nuclear Information System (INIS)
Baldwin, P.R.
1992-01-01
The problem of simultaneously approximating a vector of irrational numbers with rationals is analyzed in a geometrical setting using notions of dynamical systems theory. The author discusses here a (vectorial) multidimensional continued-fraction algorithm (MCFA) of additive type, the generalized mediant algorithm (GMA), and gives a geometrical interpretation to it. He calculates the invariant measure of the GMA shift as well as its Kolmogorov-Sinai (KS) entropy for arbitrary number of irrationals. The KS entropy is related to the growth rate of denominators of the Euclidean algorithm. This is the first analytical calculation of the growth rate of denominators for any MCFA
Multidimensional electron-photon transport with standard discrete ordinates codes
International Nuclear Information System (INIS)
Drumm, C.R.
1995-01-01
A method is described for generating electron cross sections that are compatible with standard discrete ordinates codes without modification. There are many advantages of using an established discrete ordinates solver, e.g. immediately available adjoint capability. Coupled electron-photon transport capability is needed for many applications, including the modeling of the response of electronics components to space and man-made radiation environments. The cross sections have been successfully used in the DORT, TWODANT and TORT discrete ordinates codes. The cross sections are shown to provide accurate and efficient solutions to certain multidimensional electronphoton transport problems
Compressed Subsequence Matching and Packed Tree Coloring
DEFF Research Database (Denmark)
Bille, Philip; Cording, Patrick Hagge; Gørtz, Inge Li
2017-01-01
We present a new algorithm for subsequence matching in grammar compressed strings. Given a grammar of size n compressing a string of size N and a pattern string of size m over an alphabet of size \\(\\sigma \\), our algorithm uses \\(O(n+\\frac{n\\sigma }{w})\\) space and \\(O(n+\\frac{n\\sigma }{w}+m\\log N\\log...... w\\cdot occ)\\) or \\(O(n+\\frac{n\\sigma }{w}\\log w+m\\log N\\cdot occ)\\) time. Here w is the word size and occ is the number of minimal occurrences of the pattern. Our algorithm uses less space than previous algorithms and is also faster for \\(occ=o(\\frac{n}{\\log N})\\) occurrences. The algorithm uses...... a new data structure that allows us to efficiently find the next occurrence of a given character after a given position in a compressed string. This data structure in turn is based on a new data structure for the tree color problem, where the node colors are packed in bit strings....
Multidimensional Wave Field Signal Theory: Transfer Function Relationships
Directory of Open Access Journals (Sweden)
Natalie Baddour
2012-01-01
Full Text Available The transmission of information by propagating or diffusive waves is common to many fields of engineering and physics. Such physical phenomena are governed by a Helmholtz (real wavenumber or pseudo-Helmholtz (complex wavenumber equation. Since these equations are linear, it would be useful to be able to use tools from signal theory in solving related problems. The aim of this paper is to derive multidimensional input/output transfer function relationships in the spatial domain for these equations in order to permit such a signal theoretic approach to problem solving. This paper presents such transfer function relationships for the spatial (not Fourier domain within appropriate coordinate systems. It is shown that the relationships assume particularly simple and computationally useful forms once the appropriate curvilinear version of a multidimensional spatial Fourier transform is used. These results are shown for both real and complex wavenumbers. Fourier inversion of these formulas would have applications for tomographic problems in various modalities. In the case of real wavenumbers, these inversion formulas are presented in closed form, whereby an input can be calculated from a given or measured wavefield.
SAGE - MULTIDIMENSIONAL SELF-ADAPTIVE GRID CODE
Davies, C. B.
1994-01-01
SAGE, Self Adaptive Grid codE, is a flexible tool for adapting and restructuring both 2D and 3D grids. Solution-adaptive grid methods are useful tools for efficient and accurate flow predictions. In supersonic and hypersonic flows, strong gradient regions such as shocks, contact discontinuities, shear layers, etc., require careful distribution of grid points to minimize grid error and produce accurate flow-field predictions. SAGE helps the user obtain more accurate solutions by intelligently redistributing (i.e. adapting) the original grid points based on an initial or interim flow-field solution. The user then computes a new solution using the adapted grid as input to the flow solver. The adaptive-grid methodology poses the problem in an algebraic, unidirectional manner for multi-dimensional adaptations. The procedure is analogous to applying tension and torsion spring forces proportional to the local flow gradient at every grid point and finding the equilibrium position of the resulting system of grid points. The multi-dimensional problem of grid adaption is split into a series of one-dimensional problems along the computational coordinate lines. The reduced one dimensional problem then requires a tridiagonal solver to find the location of grid points along a coordinate line. Multi-directional adaption is achieved by the sequential application of the method in each coordinate direction. The tension forces direct the redistribution of points to the strong gradient region. To maintain smoothness and a measure of orthogonality of grid lines, torsional forces are introduced that relate information between the family of lines adjacent to one another. The smoothness and orthogonality constraints are direction-dependent, since they relate only the coordinate lines that are being adapted to the neighboring lines that have already been adapted. Therefore the solutions are non-unique and depend on the order and direction of adaption. Non-uniqueness of the adapted grid is
Hashish Body Packing: A Case Report
Directory of Open Access Journals (Sweden)
Manuel Jesus Soriano-Perez
2009-01-01
Full Text Available A 42-year-old African male was brought by the police to the emergency department under suspicion of drug smuggling by body-packing. Plain abdominal radiograph showed multiple foreign bodies within the gastrointestinal tract. Contrast-enhanced abdominal CT confirmed the findings, and the patient admitted to have swallowed “balls” of hashish. Body-packing is a recognized method of smuggling drugs across international borders. Body packers may present to the emergency department because of drug toxicity, intestinal obstruction, or more commonly, requested by law-enforcement officers for medical confirmation or exclusion of suspected body packing.
Improved Taxation Rate for Bin Packing Games
Kern, Walter; Qiu, Xian
A cooperative bin packing game is a N-person game, where the player set N consists of k bins of capacity 1 each and n items of sizes a 1, ⋯ ,a n . The value of a coalition of players is defined to be the maximum total size of items in the coalition that can be packed into the bins of the coalition. We present an alternative proof for the non-emptiness of the 1/3-core for all bin packing games and show how to improve this bound ɛ= 1/3 (slightly). We conjecture that the true best possible value is ɛ= 1/7.
Multidimensional Assessment of Criminal Recidivism: Problems, Pitfalls, and Proposed Solutions
Vrieze, Scott I.; Grove, William M.
2010-01-01
All states have statutes in place to civilly commit individuals at high risk for violence. The authors address difficulties in assessing such risk but use as an example the task of predicting sexual violence recidivism; the principles espoused here generalize to predicting all violence. As part of the commitment process, mental health…
Jepsen, Charles H.
1991-01-01
Presented are solutions to variations of a combinatorics problem from a recent International Mathematics Olympiad. In particular, the matrix algebra solution illustrates an interaction among the undergraduate areas of geometry, combinatorics, linear algebra, and group theory. (JJK)
Joint mapping of genes and conditions via multidimensional unfolding analysis
Directory of Open Access Journals (Sweden)
Engelen Kristof
2007-06-01
Full Text Available Abstract Background Microarray compendia profile the expression of genes in a number of experimental conditions. Such data compendia are useful not only to group genes and conditions based on their similarity in overall expression over profiles but also to gain information on more subtle relations between genes and conditions. Getting a clear visual overview of all these patterns in a single easy-to-grasp representation is a useful preliminary analysis step: We propose to use for this purpose an advanced exploratory method, called multidimensional unfolding. Results We present a novel algorithm for multidimensional unfolding that overcomes both general problems and problems that are specific for the analysis of gene expression data sets. Applying the algorithm to two publicly available microarray compendia illustrates its power as a tool for exploratory data analysis: The unfolding analysis of a first data set resulted in a two-dimensional representation which clearly reveals temporal regulation patterns for the genes and a meaningful structure for the time points, while the analysis of a second data set showed the algorithm's ability to go beyond a mere identification of those genes that discriminate between different patient or tissue types. Conclusion Multidimensional unfolding offers a useful tool for preliminary explorations of microarray data: By relying on an easy-to-grasp low-dimensional geometric framework, relations among genes, among conditions and between genes and conditions are simultaneously represented in an accessible way which may reveal interesting patterns in the data. An additional advantage of the method is that it can be applied to the raw data without necessitating the choice of suitable genewise transformations of the data.
Comparing the efficacy of mature mud pack and hot pack treatments for knee osteoarthritis.
Sarsan, Ayşe; Akkaya, Nuray; Ozgen, Merih; Yildiz, Necmettin; Atalay, Nilgun Simsir; Ardic, Fusun
2012-01-01
The objective of this study is to compare the efficacy of mature mud pack and hot pack therapies on patients with knee osteoarthritis. This study was designed as a prospective, randomized-controlled, and single-blinded clinical trial. Twenty-seven patients with clinical and radiologic evidence of knee osteoarthritis were randomly assigned into two groups and were treated with mature mud packs (n 15) or hot packs (n=12). Patients were evaluated for pain [based on the visual analog scale (VAS)], function (WOMAC, 6 min walking distance), quality of life [Short Form-36 (SF-36)], and serum levels of tumor necrosis factor-alpha (TNF-α), interleukin-6 (IL-6), and insulin-like growth factor-1 (IGF-1) at baseline, post-treatment, and 3 and 6~months after treatment. The mud pack group shows a significant improvement in VAS, pain, stifness, and physical function domains of WOMAC. The difference between groups of pain and physical activity domains is significant at post-treatment in favor of mud pack. For a 6 min walking distance, mud pack shows significant improvement, and the difference is significant between groups in favor of mud pack at post-treatment and 3 and 6 months after treatment. Mud pack shows significant improvement in the pain subscale of SF-36 at the third month continuing until the sixth month after the treatment. Significant improvements are found for the social function, vitality/energy, physical role disability, and general health subscales of SF-36 in favor of the mud pack compared with the hot pack group at post-treatment. A significant increase is detected for IGF-1 in the mud pack group 3 months after treatment compared with the baseline, and the difference is significant between groups 3 months after the treatment. Mud pack is a favorable option compared with hotpack for pain relief and for the improvement of functional conditions in treating patients with knee osteoarthritis.
Interferometric redatuming by multidimensional deconvolution
Van der Neut, J.R.
2012-01-01
Seismic reflection imaging is a popular method to image, characterize and monitor the Earth's subsurface. In this method, seismic signals are sent into the subsurface and their reflections are collected. Strong heterogeneities in upper sections of the subsurface often pose a problem for imaging deeper sections. To overcome these problems, it has been proposed to place receivers in a horizontal, deviated or vertical borehole and to turn these receivers into virtual sources by seismic interfero...
Packing circles and spheres on surfaces
Schiftner, Alexander; Hö binger, Mathias; Wallner, Johannes; Pottmann, Helmut
2009-01-01
Inspired by freeform designs in architecture which involve circles and spheres, we introduce a new kind of triangle mesh whose faces' incircles form a packing. As it turns out, such meshes have a rich geometry and allow us to cover surfaces with circle patterns, sphere packings, approximate circle packings, hexagonal meshes which carry a torsion-free support structure, hybrid tri-hex meshes, and others. We show how triangle meshes can be optimized so as to have the incircle packing property. We explain their relation to conformal geometry and implications on solvability of optimization. The examples we give confirm that this kind of meshes is a rich source of geometric structures relevant to architectural geometry. © 2009 ACM.
Prevention and suppression of metal packing fires.
Roberts, Mark; Rogers, William J; Sam Mannan, M; Ostrowski, Scott W
2003-11-14
Structured packing has been widely used because of large surface area that makes possible columns with high capacity and efficiency. The large surface area also contributes to fire hazards because of hydrocarbon deposits that can easily combust and promote combustion of the thin metal packing materials. Materials of high surface area that can fuel fires include reactive metals, such as titanium, and materials that are not considered combustible, such as stainless steel. Column design and material selection for packing construction is discussed together with employee training and practices for safe column maintenance and operations. Presented also are methods and agents for suppression of metal fires. Guidance for prevention and suppression of metal fires is related to incidents involving packing fires in columns.
Packing circles and spheres on surfaces
Schiftner, Alexander
2009-12-01
Inspired by freeform designs in architecture which involve circles and spheres, we introduce a new kind of triangle mesh whose faces\\' incircles form a packing. As it turns out, such meshes have a rich geometry and allow us to cover surfaces with circle patterns, sphere packings, approximate circle packings, hexagonal meshes which carry a torsion-free support structure, hybrid tri-hex meshes, and others. We show how triangle meshes can be optimized so as to have the incircle packing property. We explain their relation to conformal geometry and implications on solvability of optimization. The examples we give confirm that this kind of meshes is a rich source of geometric structures relevant to architectural geometry.
Packing circles and spheres on surfaces
Schiftner, Alexander
2009-01-01
Inspired by freeform designs in architecture which involve circles and spheres, we introduce a new kind of triangle mesh whose faces\\' incircles form a packing. As it turns out, such meshes have a rich geometry and allow us to cover surfaces with circle patterns, sphere packings, approximate circle packings, hexagonal meshes which carry a torsion-free support structure, hybrid tri-hex meshes, and others. We show how triangle meshes can be optimized so as to have the incircle packing property. We explain their relation to conformal geometry and implications on solvability of optimization. The examples we give confirm that this kind of meshes is a rich source of geometric structures relevant to architectural geometry. © 2009 ACM.
Packing circles and spheres on surfaces
Schiftner, Alexander; Hö binger, Mathias; Wallner, Johannes; Pottmann, Helmut
2009-01-01
Inspired by freeform designs in architecture which involve circles and spheres, we introduce a new kind of triangle mesh whose faces' incircles form a packing. As it turns out, such meshes have a rich geometry and allow us to cover surfaces with circle patterns, sphere packings, approximate circle packings, hexagonal meshes which carry a torsion-free support structure, hybrid tri-hex meshes, and others. We show how triangle meshes can be optimized so as to have the incircle packing property. We explain their relation to conformal geometry and implications on solvability of optimization. The examples we give confirm that this kind of meshes is a rich source of geometric structures relevant to architectural geometry.
Random close packing in protein cores
Gaines, Jennifer C.; Smith, W. Wendell; Regan, Lynne; O'Hern, Corey S.
2015-01-01
Shortly after the determination of the first protein x-ray crystal structures, researchers analyzed their cores and reported packing fractions $\\phi \\approx 0.75$, a value that is similar to close packing equal-sized spheres. A limitation of these analyses was the use of `extended atom' models, rather than the more physically accurate `explicit hydrogen' model. The validity of using the explicit hydrogen model is proved by its ability to predict the side chain dihedral angle distributions obs...
Granular packing as model glass formers
International Nuclear Information System (INIS)
Wang Yujie
2017-01-01
Static granular packings are model hard-sphere glass formers. The nature of glass transition has remained a hotly debated issue. We review recent experimental progresses in using granular materials to study glass transitions. We focus on the growth of glass order with five-fold symmetry in granular packings and relate the findings to both geometric frustration and random first-order phase transition theories. (paper)
Integrality gap analysis for bin packing games
Kern, Walter; Qui, X.
A cooperative bin packing game is an $N$-person game, where the player set $N$ consists of $k$ bins of capacity 1 each and $n$ items of sizes $a_1,\\dots,a_n$. The value $v(S)$ of a coalition $S$ of players is defined to be the maximum total size of items in $S$ that can be packed into the bins of
International Nuclear Information System (INIS)
Bareiss, E.H.
1975-01-01
The objectives of the research remain the same as outlined in the original proposal. They are in short as follows: Develop mathematically and computationally founded criteria for the design of highly efficient and reliable multi-dimensional neutron transport codes to solve a variety of neutron migration and radiation problems and analyze existing and new methods for performance. (U.S.)
Li, Q; Feng, L.; Wong, A.K.Y.
The problem of mining multidimensional inter-transactional association rules was recently introduced in [ACM Trans. Inform. Syst. 18(4) (2000) 423; Proc. of the ACM SIGMOD Workshop on Research Issues on Data Mining and Knowledge Discovery, Seattle, Washington, June 1998, p. 12:1]. It extends the
Lönngren, Johanna; Svanström, Magdalena; Ingerman, Åke; Holmberg, John
2016-01-01
The concept of perspectives is important in discussions about the multidimensionality of sustainability problems and the need to consider many different aspects when dealing with them. This paper aims to facilitate discussions among both educators and researchers about didactical approaches to developing students' abilities to deal with the…
International Nuclear Information System (INIS)
Bareiss, E.H.
1977-08-01
The objectives of this research are to develop mathematically and computationally founded criteria for the design of highly efficient and reliable multidimensional neutron transport codes to solve a variety of neutron migration and radiation problems, and to analyze existing and new methods for performance
Development of a leadership resource pack
Energy Technology Data Exchange (ETDEWEB)
NONE
2001-07-01
The pack contains notes and presentation material for OSD inspectors to help them prepare for health and safety discussions with senior managers. The successful application of the leadership resource pack depends on an inspector gaining familiarity with the contents of the pack. Flexibility and adaptability were considered crucial factors in developing the contents. The pack is not considered a substitute for an inspector's own experience, knowledge or substitute for prior research. The leadership resource pack is intended as a source of knowledge and good practice that demonstrates how positive leadership can drive a health and safety agenda alongside business considerations. The benefits of the leadership resource pack include: the creation of a flexible tool that inspectors can use to highlight key leadership messages in health and safety; the development of a seven-stage model for characterising senior management commitment; practical examples of how leadership in health and safety management was felt throughout nine organisations; ideas for devising an aide memoire for specific discussions with senior managers. (author)
Hardfacing and packings for improved valve performance
International Nuclear Information System (INIS)
Aikin, J.A.; Patrick, J.N.F.; Inglis, I.
2003-01-01
The CANDU Owners Group (COG), Chemistry, Materials and Components (CMC) Program has supported an ongoing program on valve maintenance and performance for several years. An overview is presented of recent work on iron-based hardfacing, packing qualification, friction testing of polytetrafluoroethylene (PTFE) packings, and an investigation of re-torquing valve packing. Based on this program, two new valve-packing materials have been qualified for use in CANDU stations. By doing this, CANDU maintenance can avoid having only one packing qualified for station use, as well as assess the potential impact of the industry trend towards using lower gland loads. The results from corrosion tests by AECL and the coefficient of friction studies at Battelle' s tribology testing facilities on Delcrome 910, an iron-based hardfacing alloy, indicate it is an acceptable replacement for Stellite 6 under certain conditions. This information can be used to update in-line valve purchasing specifications. The renewed interest in friction characteristics, and environmental qualification (EQ) of packing containing PTFE has resulted in a new test program in these areas. The COG-funded valve programs have resulted in modifications to design specifications for nuclear station in-line valves and have led to better maintenance practices and valve reliability. In the end, this means lower costs and cheaper electricity. (author)
Intuitionistic fuzzy (IF) evaluations of multidimensional model
International Nuclear Information System (INIS)
Valova, I.
2012-01-01
There are different logical methods for data structuring, but no one is perfect enough. Multidimensional model-MD of data is presentation of data in a form of cube (referred also as info-cube or hypercube) with data or in form of 'star' type scheme (referred as multidimensional scheme), by use of F-structures (Facts) and set of D-structures (Dimensions), based on the notion of hierarchy of D-structures. The data, being subject of analysis in a specific multidimensional model is located in a Cartesian space, being restricted by D-structures. In fact, the data is either dispersed or 'concentrated', therefore the data cells are not distributed evenly within the respective space. The moment of occurrence of any event is difficult to be predicted and the data is concentrated as per time periods, location of performed business event, etc. To process such dispersed or concentrated data, various technical strategies are needed. The basic methods for presentation of such data should be selected. The approaches of data processing and respective calculations are connected with different options for data representation. The use of intuitionistic fuzzy evaluations (IFE) provide us new possibilities for alternative presentation and processing of data, subject of analysis in any OLAP application. The use of IFE at the evaluation of multidimensional models will result in the following advantages: analysts will dispose with more complete information for processing and analysis of respective data; benefit for the managers is that the final decisions will be more effective ones; enabling design of more functional multidimensional schemes. The purpose of this work is to apply intuitionistic fuzzy evaluations of multidimensional model of data. (authors)
Multi-Dimensional Aggregation for Temporal Data
DEFF Research Database (Denmark)
Böhlen, M. H.; Gamper, J.; Jensen, Christian Søndergaard
2006-01-01
Business Intelligence solutions, encompassing technologies such as multi-dimensional data modeling and aggregate query processing, are being applied increasingly to non-traditional data. This paper extends multi-dimensional aggregation to apply to data with associated interval values that capture...... that the data holds for each point in the interval, as well as the case where the data holds only for the entire interval, but must be adjusted to apply to sub-intervals. The paper reports on an implementation of the new operator and on an empirical study that indicates that the operator scales to large data...
Simulation of a Multidimensional Input Quantum Perceptron
Yamamoto, Alexandre Y.; Sundqvist, Kyle M.; Li, Peng; Harris, H. Rusty
2018-06-01
In this work, we demonstrate the improved data separation capabilities of the Multidimensional Input Quantum Perceptron (MDIQP), a fundamental cell for the construction of more complex Quantum Artificial Neural Networks (QANNs). This is done by using input controlled alterations of ancillary qubits in combination with phase estimation and learning algorithms. The MDIQP is capable of processing quantum information and classifying multidimensional data that may not be linearly separable, extending the capabilities of the classical perceptron. With this powerful component, we get much closer to the achievement of a feedforward multilayer QANN, which would be able to represent and classify arbitrary sets of data (both quantum and classical).
A lifelong learning hyper-heuristic method for bin packing.
Sim, Kevin; Hart, Emma; Paechter, Ben
2015-01-01
We describe a novel hyper-heuristic system that continuously learns over time to solve a combinatorial optimisation problem. The system continuously generates new heuristics and samples problems from its environment; and representative problems and heuristics are incorporated into a self-sustaining network of interacting entities inspired by methods in artificial immune systems. The network is plastic in both its structure and content, leading to the following properties: it exploits existing knowledge captured in the network to rapidly produce solutions; it can adapt to new problems with widely differing characteristics; and it is capable of generalising over the problem space. The system is tested on a large corpus of 3,968 new instances of 1D bin-packing problems as well as on 1,370 existing problems from the literature; it shows excellent performance in terms of the quality of solutions obtained across the datasets and in adapting to dynamically changing sets of problem instances compared to previous approaches. As the network self-adapts to sustain a minimal repertoire of both problems and heuristics that form a representative map of the problem space, the system is further shown to be computationally efficient and therefore scalable.
Theory and application of deterministic multidimensional pointwise energy lattice physics methods
International Nuclear Information System (INIS)
Zerkle, M.L.
1999-01-01
The theory and application of deterministic, multidimensional, pointwise energy lattice physics methods are discussed. These methods may be used to solve the neutron transport equation in multidimensional geometries using near-continuous energy detail to calculate equivalent few-group diffusion theory constants that rigorously account for spatial and spectral self-shielding effects. A dual energy resolution slowing down algorithm is described which reduces the computer memory and disk storage requirements for the slowing down calculation. Results are presented for a 2D BWR pin cell depletion benchmark problem
International Nuclear Information System (INIS)
Kifonidis, K.; Mueller, E.; Plewa, T.
2001-01-01
After decades of one-dimensional nucleosynthesis calculations, the growth of computational resources has meanwhile reached a level, which for the first time allows astrophysicists to consider performing routinely realistic multidimensional nucleosynthesis calculations in explosive and, to some extent, also in non-explosive environments. In the present contribution we attempt to give a short overview of the physical and numerical problems which are encountered in these simulations. In addition, we assess the accuracy that can be currently achieved in the computation of nucleosynthetic yields, using multidimensional simulations of core collapse supernovae as an example
International Nuclear Information System (INIS)
Lee, Seok Min; Lee, Un Chul; Bae, Sung Won; Chung, Bub Dong
2004-01-01
The Multi-Dimensional flow models in system code have been developed during the past many years. RELAP5-3D, CATHARE and TRACE has its specific multi-dimensional flow models and successfully applied it to the system safety analysis. In KAERI, also, MARS(Multi-dimensional Analysis of Reactor Safety) code was developed by integrating RELAP5/MOD3 code and COBRA-TF code. Even though COBRA-TF module can analyze three-dimensional flow models, it has a limitation to apply 3D shear stress dominant phenomena or cylindrical geometry. Therefore, Multi-dimensional analysis models are newly developed by implementing three-dimensional momentum flux and diffusion terms. The multi-dimensional model has been assessed compared with multi-dimensional conceptual problems and CFD code results. Although the assessment results were reasonable, the multi-dimensional model has not been validated to two-phase flow using experimental data. In this paper, the multi-dimensional air-water two-phase flow experiment was simulated and analyzed
Multi objective optimization of line pack management of gas pipeline system
International Nuclear Information System (INIS)
Chebouba, A
2015-01-01
This paper addresses the Line Pack Management of the ''GZ1 Hassi R'mell-Arzew'' gas pipeline. For a gas pipeline system, the decision-making on the gas line pack management scenarios usually involves a delicate balance between minimization of the fuel consumption in the compression stations and maximizing gas line pack. In order to select an acceptable Line Pack Management of Gas Pipeline scenario from these two angles for ''GZ1 Hassi R'mell- Arzew'' gas pipeline, the idea of multi-objective decision-making has been introduced. The first step in developing this approach is the derivation of a numerical method to analyze the flow through the pipeline under transient isothermal conditions. In this paper, the solver NSGA-II of the modeFRONTIER, coupled with a matlab program was used for solving the multi-objective problem
Multi-dimensional simulations of core-collapse supernova explosions with CHIMERA
Messer, O. E. B.; Harris, J. A.; Hix, W. R.; Lentz, E. J.; Bruenn, S. W.; Mezzacappa, A.
2018-04-01
Unraveling the core-collapse supernova (CCSN) mechanism is a problem that remains essentially unsolved despite more than four decades of effort. Spherically symmetric models with otherwise high physical fidelity generally fail to produce explosions, and it is widely accepted that CCSNe are inherently multi-dimensional. Progress in realistic modeling has occurred recently through the availability of petascale platforms and the increasing sophistication of supernova codes. We will discuss our most recent work on understanding neutrino-driven CCSN explosions employing multi-dimensional neutrino-radiation hydrodynamics simulations with the Chimera code. We discuss the inputs and resulting outputs from these simulations, the role of neutrino radiation transport, and the importance of multi-dimensional fluid flows in shaping the explosions. We also highlight the production of 48Ca in long-running Chimera simulations.
Paardekooper, S.-J.
2017-08-01
We present a new method for numerical hydrodynamics which uses a multidimensional generalization of the Roe solver and operates on an unstructured triangular mesh. The main advantage over traditional methods based on Riemann solvers, which commonly use one-dimensional flux estimates as building blocks for a multidimensional integration, is its inherently multidimensional nature, and as a consequence its ability to recognize multidimensional stationary states that are not hydrostatic. A second novelty is the focus on graphics processing units (GPUs). By tailoring the algorithms specifically to GPUs, we are able to get speedups of 100-250 compared to a desktop machine. We compare the multidimensional upwind scheme to a traditional, dimensionally split implementation of the Roe solver on several test problems, and we find that the new method significantly outperforms the Roe solver in almost all cases. This comes with increased computational costs per time-step, which makes the new method approximately a factor of 2 slower than a dimensionally split scheme acting on a structured grid.
Benchmarking multi-dimensional large strain consolidation analyses
International Nuclear Information System (INIS)
Priestley, D.; Fredlund, M.D.; Van Zyl, D.
2010-01-01
Analyzing the consolidation of tailings slurries and dredged fills requires a more extensive formulation than is used for common (small strain) consolidation problems. Large strain consolidation theories have traditionally been limited to 1-D formulations. SoilVision Systems has developed the capacity to analyze large strain consolidation problems in 2 and 3-D. The benchmarking of such formulations is not a trivial task. This paper presents several examples of modeling large strain consolidation in the beta versions of the new software. These examples were taken from the literature and were used to benchmark the large strain formulation used by the new software. The benchmarks reported here are: a comparison to the consolidation software application CONDES0, Townsend's Scenario B and a multi-dimensional analysis of long-term column tests performed on oil sands tailings. All three of these benchmarks were attained using the SVOffice suite. (author)
Application of multidimensional IRT models to longitudinal data
te Marvelde, J.M.; Glas, Cornelis A.W.; Van Landeghem, Georges; Van Damme, Jan
2006-01-01
The application of multidimensional item response theory (IRT) models to longitudinal educational surveys where students are repeatedly measured is discussed and exemplified. A marginal maximum likelihood (MML) method to estimate the parameters of a multidimensional generalized partial credit model
The emergence and evolution of the multidimensional organization
Strikwerda, J.; Stoelhorst, J.W.
2009-01-01
The article discusses multidimensional organizations and the evolution of complex organizations. The six characteristics of multidimensional organizations, disadvantages of the successful organizational structure that is categorized as a multidivisional, multi-unit or M-form, research by the
Multidimensional Screening as a Pharmacology Laboratory Experience.
Malone, Marvin H.; And Others
1979-01-01
A multidimensional pharmacodynamic screening experiment that addresses drug interaction is included in the pharmacology-toxicology laboratory experience of pharmacy students at the University of the Pacific. The student handout with directions for the procedure is reproduced, drug compounds tested are listed, and laboratory evaluation results are…
Continued validation of the Multidimensional Perfectionism Scale.
Clavin, S L; Clavin, R H; Gayton, W F; Broida, J
1996-06-01
Scores on the Multidimensional Perfectionism Scale have been correlated with measures of obsessive-compulsive tendencies for women, so the validity of scores on this scale for 41 men was examined. Scores on the Perfectionism Scale were significantly correlated (.47-.03) with scores on the Maudsley Obsessive-Compulsive Inventory.
Multi-dimensional indoor location information model
Xiong, Q.; Zhu, Q.; Zlatanova, S.; Huang, L.; Zhou, Y.; Du, Z.
2013-01-01
Aiming at the increasing requirements of seamless indoor and outdoor navigation and location service, a Chinese standard of Multidimensional Indoor Location Information Model is being developed, which defines ontology of indoor location. The model is complementary to 3D concepts like CityGML and
Multi-dimensional quasitoeplitz Markov chains
Directory of Open Access Journals (Sweden)
Alexander N. Dudin
1999-01-01
Full Text Available This paper deals with multi-dimensional quasitoeplitz Markov chains. We establish a sufficient equilibrium condition and derive a functional matrix equation for the corresponding vector-generating function, whose solution is given algorithmically. The results are demonstrated in the form of examples and applications in queues with BMAP-input, which operate in synchronous random environment.
Multidimensional human dynamics in mobile phone communications.
Quadri, Christian; Zignani, Matteo; Capra, Lorenzo; Gaito, Sabrina; Rossi, Gian Paolo
2014-01-01
In today's technology-assisted society, social interactions may be expressed through a variety of techno-communication channels, including online social networks, email and mobile phones (calls, text messages). Consequently, a clear grasp of human behavior through the diverse communication media is considered a key factor in understanding the formation of the today's information society. So far, all previous research on user communication behavior has focused on a sole communication activity. In this paper we move forward another step on this research path by performing a multidimensional study of human sociality as an expression of the use of mobile phones. The paper focuses on user temporal communication behavior in the interplay between the two complementary communication media, text messages and phone calls, that represent the bi-dimensional scenario of analysis. Our study provides a theoretical framework for analyzing multidimensional bursts as the most general burst category, that includes one-dimensional bursts as the simplest case, and offers empirical evidence of their nature by following the combined phone call/text message communication patterns of approximately one million people over three-month period. This quantitative approach enables the design of a generative model rooted in the three most significant features of the multidimensional burst - the number of dimensions, prevalence and interleaving degree - able to reproduce the main media usage attitude. The other findings of the paper include a novel multidimensional burst detection algorithm and an insight analysis of the human media selection process.
Multidimensional stochastic approximation using locally contractive functions
Lawton, W. M.
1975-01-01
A Robbins-Monro type multidimensional stochastic approximation algorithm which converges in mean square and with probability one to the fixed point of a locally contractive regression function is developed. The algorithm is applied to obtain maximum likelihood estimates of the parameters for a mixture of multivariate normal distributions.
Multidimensional human dynamics in mobile phone communications.
Directory of Open Access Journals (Sweden)
Christian Quadri
Full Text Available In today's technology-assisted society, social interactions may be expressed through a variety of techno-communication channels, including online social networks, email and mobile phones (calls, text messages. Consequently, a clear grasp of human behavior through the diverse communication media is considered a key factor in understanding the formation of the today's information society. So far, all previous research on user communication behavior has focused on a sole communication activity. In this paper we move forward another step on this research path by performing a multidimensional study of human sociality as an expression of the use of mobile phones. The paper focuses on user temporal communication behavior in the interplay between the two complementary communication media, text messages and phone calls, that represent the bi-dimensional scenario of analysis. Our study provides a theoretical framework for analyzing multidimensional bursts as the most general burst category, that includes one-dimensional bursts as the simplest case, and offers empirical evidence of their nature by following the combined phone call/text message communication patterns of approximately one million people over three-month period. This quantitative approach enables the design of a generative model rooted in the three most significant features of the multidimensional burst - the number of dimensions, prevalence and interleaving degree - able to reproduce the main media usage attitude. The other findings of the paper include a novel multidimensional burst detection algorithm and an insight analysis of the human media selection process.
MCMC estimation of multidimensional IRT models
Beguin, Anton; Glas, Cornelis A.W.
1998-01-01
A Bayesian procedure to estimate the three-parameter normal ogive model and a generalization to a model with multidimensional ability parameters are discussed. The procedure is a generalization of a procedure by J. Albert (1992) for estimating the two-parameter normal ogive model. The procedure will
27 CFR 24.308 - Bottled or packed wine record.
2010-04-01
... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Bottled or packed wine... BUREAU, DEPARTMENT OF THE TREASURY LIQUORS WINE Records and Reports § 24.308 Bottled or packed wine record. A proprietor who bottles, packs, or receives bottled or packed beverage wine in bond shall...
Coalescence preference in dense packing of bubbles
Kim, Yeseul; Gim, Bopil; Gim, Bopil; Weon, Byung Mook
2015-11-01
Coalescence preference is the tendency that a merged bubble from the contact of two original bubbles (parent) tends to be near to the bigger parent. Here, we show that the coalescence preference can be blocked by densely packing of neighbor bubbles. We use high-speed high-resolution X-ray microscopy to clearly visualize individual coalescence phenomenon which occurs in micro scale seconds and inside dense packing of microbubbles with a local packing fraction of ~40%. Previous theory and experimental evidence predict a power of -5 between the relative coalescence position and the parent size. However, our new observation for coalescence preference in densely packed microbubbles shows a different power of -2. We believe that this result may be important to understand coalescence dynamics in dense packing of soft matter. This work (NRF-2013R1A22A04008115) was supported by Mid-career Researcher Program through NRF grant funded by the MEST and also was supported by Ministry of Science, ICT and Future Planning (2009-0082580) and by Basic Science Research Program through the National Research Foundation of Korea (NRF) funded by the Ministry and Education, Science and Technology (NRF-2012R1A6A3A04039257).
Multidimensional Data Model and Query Language for Informetrics.
Niemi, Timo; Hirvonen, Lasse; Jarvelin, Kalervo
2003-01-01
Discusses multidimensional data analysis, or online analytical processing (OLAP), which offer a single subject-oriented source for analyzing summary data based on various dimensions. Develops a conceptual/logical multidimensional model for supporting the needs of informetrics, including a multidimensional query language whose basic idea is to…
Development of Multidimensional Gap Conductance model using Virtual Link Gap Element
Energy Technology Data Exchange (ETDEWEB)
Kim, Hyo Chan; Yang, Yong Sik; Kim, Dae Ho; Bang, Je Geon; Kim, Sun Ki; Koo, Yang Hyun [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)
2013-10-15
The gap conductance that determines temperature gradient between pellet and cladding can be quite sensitive to gap thickness. For instance, once the gap size increases up to several micrometers in certain region, difference of pellet surface temperatures increases up to 100 Kelvin. Therefore, iterative thermo-mechanical coupled analysis is required to solve temperature distribution throughout pellet and cladding. Recently, multidimensional fuel performance codes have been being developed in the advanced countries to evaluate thermal behavior of fuel for off normal conditions and DBA(design based accident) conditions using the Finite Element Method (FEM). FRAPCON-FRAPTRAN code system, which is well known as the verified and reliable code, incorporates 1D thermal module and multidimensional mechanical module. In this code, multidimensional gap conductance model is not applied. ALCYONE developed by CEA introduces equivalent heat convection coefficient that represents multidimensional gap conductance as a function of gap thickness. BISON, which is multidimensional fuel performance code developed by INL, owns multidimensional gap conductance model using projected thermal contact. In general, thermal contact algorithm is nonlinear calculation which is expensive approach numerically. The gap conductance model for multi-dimension is difficult issue in terms of convergence and nonlinearity because gap conductance is function of gap thickness which depends on mechanical analysis at each iteration step. In this paper, virtual link gap (VLG) element has been proposed to resolve convergence issue and nonlinear characteristic of multidimensional gap conductance. In terms of calculation accuracy and convergence efficiency, the proposed VLG model was evaluated. LWR fuel performance codes should incorporate thermo-mechanical loop to solve gap conductance problem, iteratively. However, gap conductance in multidimensional model is difficult issue owing to its nonlinearity and
Two-stage energy storage equalization system for lithium-ion battery pack
Chen, W.; Yang, Z. X.; Dong, G. Q.; Li, Y. B.; He, Q. Y.
2017-11-01
How to raise the efficiency of energy storage and maximize storage capacity is a core problem in current energy storage management. For that, two-stage energy storage equalization system which contains two-stage equalization topology and control strategy based on a symmetric multi-winding transformer and DC-DC (direct current-direct current) converter is proposed with bidirectional active equalization theory, in order to realize the objectives of consistent lithium-ion battery packs voltages and cells voltages inside packs by using a method of the Range. Modeling analysis demonstrates that the voltage dispersion of lithium-ion battery packs and cells inside packs can be kept within 2 percent during charging and discharging. Equalization time was 0.5 ms, which shortened equalization time of 33.3 percent compared with DC-DC converter. Therefore, the proposed two-stage lithium-ion battery equalization system can achieve maximum storage capacity between lithium-ion battery packs and cells inside packs, meanwhile efficiency of energy storage is significantly improved.
Packing of ganglioside-phospholipid monolayers
DEFF Research Database (Denmark)
Majewski, J.; Kuhl, T.L.; Kjær, K.
2001-01-01
Using synchrotron grazing-incidence x-ray diffraction (GIXD) and reflectivity, the in-plane and out-of-plane structure of mixed ganglioside-phospholipid monolayers was investigated at the air-water interface. Mixed monolayers of 0, 5, 10, 20, and 100 mol% ganglioside GM, and the phospholipid...... monolayers did not affect hydrocarbon tail packing (fluidization or condensation of the hydrocarbon region). This is in contrast to previous investigations of lipopolymer-lipid mixtures, where the packing structure of phospholipid monolayers was greatly altered by the inclusion of lipids bearing hydrophilic...
Used fuel packing plant for CANDU fuel
Energy Technology Data Exchange (ETDEWEB)
Menzies, I.; Thayer, B.; Bains, N., E-mail: imenzies@atsautomation.com [ATS Automation, Cambridge, ON (Canada); Murchison, A., E-mail: amurchison@nwmo.ca [NWMO, Toronto, ON (Canada)
2015-07-01
Large forgings have been selected to containerize Light Water Reactor used nuclear fuel. CANDU fuel, which is significantly smaller in size, allows novel approaches for containerization. For example, by utilizing commercially available extruded ASME pipe a conceptual design of a Used Fuel Packing Plant for containerization of used CANDU fuel in a long lived metallic container has been developed. The design adopts a modular approach with multiple independent work cells to transfer and containerize the used fuel. Based on current technologies and concepts from proven industrial systems, the Used Fuel Packing Plant can assemble twelve used fuel containers per day considering conservative levels of process availability. (author)
Cylinder packing by simulated annealing
Directory of Open Access Journals (Sweden)
M. Helena Correia
2000-12-01
Full Text Available This paper is motivated by the problem of loading identical items of circular base (tubes, rolls, ... into a rectangular base (the pallet. For practical reasons, all the loaded items are considered to have the same height. The resolution of this problem consists in determining the positioning pattern of the circular bases of the items on the rectangular pallet, while maximizing the number of items. This pattern will be repeated for each layer stacked on the pallet. Two algorithms based on the meta-heuristic Simulated Annealing have been developed and implemented. The tuning of these algorithms parameters implied running intensive tests in order to improve its efficiency. The algorithms developed were easily extended to the case of non-identical circles.Este artigo aborda o problema de posicionamento de objetos de base circular (tubos, rolos, ... sobre uma base retangular de maiores dimensões. Por razões práticas, considera-se que todos os objetos a carregar apresentam a mesma altura. A resolução do problema consiste na determinação do padrão de posicionamento das bases circulares dos referidos objetos sobre a base de forma retangular, tendo como objetivo a maximização do número de objetos estritamente posicionados no interior dessa base. Este padrão de posicionamento será repetido em cada uma das camadas a carregar sobre a base retangular. Apresentam-se dois algoritmos para a resolução do problema. Estes algoritmos baseiam-se numa meta-heurística, Simulated Annealling, cuja afinação de parâmetros requereu a execução de testes intensivos com o objetivo de atingir um elevado grau de eficiência no seu desempenho. As características dos algoritmos implementados permitiram que a sua extensão à consideração de círculos com raios diferentes fosse facilmente conseguida.
Propagation of Singularities and Some Inverse Problems in Wave Propagation
National Research Council Canada - National Science Library
Symes, William W
1989-01-01
... in various useful coefficient classes, separation of scales,...We explain the essential role of travel time in the study of these problems, and show how its function may be generalized to multidimensional (i.e. non-layered) problems.
A Cost Assessment of the Dayton Public Schools Vehicle Routing Problem
2009-03-01
known problems: the Traveling Salesman Problem (TSP) and the Bin Packing Problem ( BPP ) (Ralphs, 2003). The VRP has a plethora of real world...well known problems: the Traveling Salesman Problem (TSP) and the Bin Packing Problem ( BPP ) (Ralphs, 2003). The VRP has a plethora of real world
Submaximal Riemann-Roch expected curves and symplectic packing.
Directory of Open Access Journals (Sweden)
Wioletta Syzdek
2007-06-01
Full Text Available We study Riemann-Roch expected curves on $mathbb{P}^1 imes mathbb{P}^1$ in the context of the Nagata-Biran conjecture. This conjecture predicts that for sufficiently large number of points multiple points Seshadri constants of an ample line bundle on algebraic surface are maximal. Biran gives an effective lower bound $N_0$. We construct examples verifying to the effect that the assertions of the Nagata-Biran conjecture can not hold for small number of points. We discuss cases where our construction fails. We observe also that there exists a strong relation between Riemann-Roch expected curves on $mathbb{P}^1 imes mathbb{P}^1$ and the symplectic packing problem. Biran relates the packing problem to the existence of solutions of certain Diophantine equations. We construct such solutions for any ample line bundle on $mathbb{P}^1 imes mathbb{P}^1$ and a relatively smallnumber of points. The solutions geometrically correspond to Riemann-Roch expected curves. Finally we discuss in how far the Biran number $N_0$ is optimal in the case of mathbb{P}^1 imes mathbb{P}^1. In fact we conjecture that it can be replaced by a lower number and we provide evidence justifying this conjecture.
Finite element method for radiation heat transfer in multi-dimensional graded index medium
International Nuclear Information System (INIS)
Liu, L.H.; Zhang, L.; Tan, H.P.
2006-01-01
In graded index medium, ray goes along a curved path determined by Fermat principle, and curved ray-tracing is very difficult and complex. To avoid the complicated and time-consuming computation of curved ray trajectories, a finite element method based on discrete ordinate equation is developed to solve the radiative transfer problem in a multi-dimensional semitransparent graded index medium. Two particular test problems of radiative transfer are taken as examples to verify this finite element method. The predicted dimensionless net radiative heat fluxes are determined by the proposed method and compared with the results obtained by finite volume method. The results show that the finite element method presented in this paper has a good accuracy in solving the multi-dimensional radiative transfer problem in semitransparent graded index medium
Uher, Vojtěch; Gajdoš, Petr; Radecký, Michal; Snášel, Václav
2016-01-01
The Differential Evolution (DE) is a widely used bioinspired optimization algorithm developed by Storn and Price. It is popular for its simplicity and robustness. This algorithm was primarily designed for real-valued problems and continuous functions, but several modified versions optimizing both integer and discrete-valued problems have been developed. The discrete-coded DE has been mostly used for combinatorial problems in a set of enumerative variants. However, the DE has a great potential in the spatial data analysis and pattern recognition. This paper formulates the problem as a search of a combination of distinct vertices which meet the specified conditions. It proposes a novel approach called the Multidimensional Discrete Differential Evolution (MDDE) applying the principle of the discrete-coded DE in discrete point clouds (PCs). The paper examines the local searching abilities of the MDDE and its convergence to the global optimum in the PCs. The multidimensional discrete vertices cannot be simply ordered to get a convenient course of the discrete data, which is crucial for good convergence of a population. A novel mutation operator utilizing linear ordering of spatial data based on the space filling curves is introduced. The algorithm is tested on several spatial datasets and optimization problems. The experiments show that the MDDE is an efficient and fast method for discrete optimizations in the multidimensional point clouds.
Pearson, Jennifer L; Richardson, Amanda; Feirman, Shari P; Villanti, Andrea C; Cantrell, Jennifer; Cohn, Amy; Tacelosky, Michael; Kirchner, Thomas R
2016-08-01
In 2015, the Food and Drug Administration issued warnings to three tobacco manufacturers who label their cigarettes as "additive-free" and/or "natural" on the grounds that they make unauthorized reduced risk claims. The goal of this study was to examine US adults' perceptions of three American Spirit (AS) pack descriptors ("Made with Organic Tobacco," "100% Additive-Free," and "100% US Grown Tobacco") to assess if they communicate reduced risk. In September 2012, three cross-sectional surveys were posted on Amazon Mechanical Turk. Adult participants evaluated the relative harm of a Marlboro Red pack versus three different AS packs with the descriptors "Made with Organic Tobacco," "100% Additive-Free," or "100% US Grown Tobacco" (Survey 1; n = 461); a Marlboro Red pack versus these AS packs modified to exclude descriptors (Survey 2; n = 857); and unmodified versus modified AS pack images (Survey 3; n = 1001). The majority of Survey 1 participants rated the unmodified AS packs as less harmful than the Marlboro Red pack; 35.4%-58.8% of Survey 2 participants also rated the modified (no claims) packs as less harmful than Marlboro Red. In these surveys, prior use of AS cigarettes was associated with reduced perceptions of risk (adjusted odds ratio [AOR] 1.59-2.40). "Made with Organic Tobacco" and "100% Additive-Free" were associated with reduced perceptions of risk when comparing the modified versus the unmodified AS packs (Survey 3). Data suggest that these AS pack descriptors communicate reduced harm messages to consumers. Findings have implications for regulatory actions related to product labeling and packaging. These findings provide additional evidence that the "Made with Organic Tobacco," "100% Additive-Free," and "100% US Grown" descriptors, as well as other aspects of the AS pack design, communicate reduced harm to non-, current, and former smokers. Additionally, they provide support for the importance of FDA's 2015 warning to Santa Fe Natural Tobacco Company on
Random close packing in protein cores.
Gaines, Jennifer C; Smith, W Wendell; Regan, Lynne; O'Hern, Corey S
2016-03-01
Shortly after the determination of the first protein x-ray crystal structures, researchers analyzed their cores and reported packing fractions ϕ ≈ 0.75, a value that is similar to close packing of equal-sized spheres. A limitation of these analyses was the use of extended atom models, rather than the more physically accurate explicit hydrogen model. The validity of the explicit hydrogen model was proved in our previous studies by its ability to predict the side chain dihedral angle distributions observed in proteins. In contrast, the extended atom model is not able to recapitulate the side chain dihedral angle distributions, and gives rise to large atomic clashes at side chain dihedral angle combinations that are highly probable in protein crystal structures. Here, we employ the explicit hydrogen model to calculate the packing fraction of the cores of over 200 high-resolution protein structures. We find that these protein cores have ϕ ≈ 0.56, which is similar to results obtained from simulations of random packings of individual amino acids. This result provides a deeper understanding of the physical basis of protein structure that will enable predictions of the effects of amino acid mutations to protein cores and interfaces of known structure.
Granular packings with moving side walls
International Nuclear Information System (INIS)
Landry, James W.; Grest, Gary Stephen
2004-01-01
The effects of movement of the side walls of a confined granular packing are studied by discrete element, molecular dynamics simulations. The dynamical evolution of the stress is studied as a function of wall movement both in the direction of gravity as well as opposite to it. For all wall velocities explored, the stress in the final state of the system after wall movement is fundamentally different from the original state obtained by pouring particles into the container and letting them settle under the influence of gravity. The original packing possesses a hydrostaticlike region at the top of the container which crosses over to a depth-independent stress. As the walls are moved in the direction opposite to gravity, the saturation stress first reaches a minimum value independent of the wall velocity, then increases to a steady-state value dependent on the wall velocity. After wall movement ceases and the packing reaches equilibrium, the stress profile fits the classic Janssen form for high wall velocities, while some deviations remain for low wall velocities. The wall movement greatly increases the number of particle-wall and particle-particle forces at the Coulomb criterion. Varying the wall velocity has only small effects on the particle structure of the final packing so long as the walls travel a similar distance.
Importance of packing in spiral defect chaos
Indian Academy of Sciences (India)
We develop two measures to characterize the geometry of patterns exhibited by the state of spiral defect chaos, a weakly turbulent regime of Rayleigh-Bénard convection. These describe the packing of contiguous stripes within the pattern by quantifying their length and nearest-neighbor distributions. The distributions ...
Wrap-Attack Pack: Product Packaging Exercise
Lee, Seung Hwan; Hoffman, K. Douglas
2016-01-01
Although many marketing courses discuss traditional concepts pertaining to product strategy, concepts specifically relating to packaging are often glossed over. This exercise, "Wrap-Attack Pack," teaches students about the utilitarian and hedonic design elements of packaging. More specifically, the primary objective is to creatively…
Simple Cloud Chambers Using Gel Ice Packs
Kamata, Masahiro; Kubota, Miki
2012-01-01
Although cloud chambers are highly regarded as teaching aids for radiation education, school teachers have difficulty in using cloud chambers because they have to prepare dry ice or liquid nitrogen before the experiment. We developed a very simple and inexpensive cloud chamber that uses the contents of gel ice packs which can substitute for dry…
The new generation of packing materials
International Nuclear Information System (INIS)
Malikov, T.S.; Dzhonmurodov, A.S.; Usmanova, S.R.; Teshaev, Kh.I.; Mukhidinov, Z.K.
2016-01-01
Present article is devoted to new generation of packing materials. The methods of extraction and investigation of component composition and properties of whey protein, zein, carboxymethylcellulose, hyaluronic acid and pectins were elaborated in order to further application them in pharmaceutical industry as composite materials and for capsulation of medicines.
Packing frustration in dense confined fluids.
Nygård, Kim; Sarman, Sten; Kjellander, Roland
2014-09-07
Packing frustration for confined fluids, i.e., the incompatibility between the preferred packing of the fluid particles and the packing constraints imposed by the confining surfaces, is studied for a dense hard-sphere fluid confined between planar hard surfaces at short separations. The detailed mechanism for the frustration is investigated via an analysis of the anisotropic pair distributions of the confined fluid, as obtained from integral equation theory for inhomogeneous fluids at pair correlation level within the anisotropic Percus-Yevick approximation. By examining the mean forces that arise from interparticle collisions around the periphery of each particle in the slit, we calculate the principal components of the mean force for the density profile--each component being the sum of collisional forces on a particle's hemisphere facing either surface. The variations of these components with the slit width give rise to rather intricate changes in the layer structure between the surfaces, but, as shown in this paper, the basis of these variations can be easily understood qualitatively and often also semi-quantitatively. It is found that the ordering of the fluid is in essence governed locally by the packing constraints at each single solid-fluid interface. A simple superposition of forces due to the presence of each surface gives surprisingly good estimates of the density profiles, but there remain nontrivial confinement effects that cannot be explained by superposition, most notably the magnitude of the excess adsorption of particles in the slit relative to bulk.
The benefits of using customized procedure packs.
Baines, R; Colquhoun, G; Jones, N; Bateman, R
2001-01-01
Discrete item purchasing is the traditional approach for hospitals to obtain consumable supplies for theatre procedures. Although most items are relatively low cost, the management and co-ordination of the supply chain, raising orders, controlling stock, picking and delivering to each operating theatre can be complex and costly. Customized procedure packs provide a solution.
Applications of Convex Analysis to Multidimensional Scaling
Jan de Leeuw
2011-01-01
In this paper we discuss the convergence of an algorithm for metric and nonmetric multidimensional scaling that is very similar to the C-matrix algorithm of Guttman. The paper improves some earlier results in two respects. In the first place the analysis is extended to cover general Minkovski metrics, in the second place a more elementary proof of convergence based on results of Robert is presented.
Multidimensional Scaling Visualization using Parametric Similarity Indices
Machado, J. A. Tenreiro; Lopes, António M.; Galhano, A.M.
2015-01-01
In this paper, we apply multidimensional scaling (MDS) and parametric similarity indices (PSI) in the analysis of complex systems (CS). Each CS is viewed as a dynamical system, exhibiting an output time-series to be interpreted as a manifestation of its behavior. We start by adopting a sliding window to sample the original data into several consecutive time periods. Second, we define a given PSI for tracking pieces of data. We then compare the windows for different values of the parameter, an...
Multi-Objective Predictive Balancing Control of Battery Packs Based on Predictive Current
Directory of Open Access Journals (Sweden)
Wenbiao Li
2016-04-01
Full Text Available Various balancing topology and control methods have been proposed for the inconsistency problem of battery packs. However, these strategies only focus on a single objective, ignore the mutual interaction among various factors and are only based on the external performance of the battery pack inconsistency, such as voltage balancing and state of charge (SOC balancing. To solve these problems, multi-objective predictive balancing control (MOPBC based on predictive current is proposed in this paper, namely, in the driving process of an electric vehicle, using predictive control to predict the battery pack output current the next time. Based on this information, the impact of the battery pack temperature caused by the output current can be obtained. Then, the influence is added to the battery pack balancing control, which makes the present degradation, temperature, and SOC imbalance achieve balance automatically due to the change of the output current the next moment. According to MOPBC, the simulation model of the balancing circuit is built with four cells in Matlab/Simulink. The simulation results show that MOPBC is not only better than the other traditional balancing control strategies but also reduces the energy loss in the balancing process.
International Nuclear Information System (INIS)
Siemer, D.D.
1989-01-01
A substantial fraction of the finely divided undissolved solid material found in nuclear fuel reprocessing dissolver-product solutions is hydrophobic and tends to ''seek'' any organic-aqueous interface existing within countercurrent liquid-liquid extraction systems. While passing through pulsed-type columns this material is swept out of the aqueous phase by the combined surface area of the tiny bubbles of dispersed phase. Because these bubbles have a net velocity towards the end of the column where the nominal interface is located, the solids are swept in that direction too. These solids tend to gather in a three-phase ''crud'' layer at the nominal interface point. At equilibrium, about the same amount breaks off from the crud layer and escapes into the liquid exiting from that end of the column as enters it from the other side. If large enough, the crud layer can even interfere with interface detection and control equipment. In packed-column extraction systems, an additional problem is that feed solids can accumulate within the packing material to the point that the column '' floods'' or even totally plugs. The keys to preventing solids-related problems is the correct choice of interface level, and with packed columns, the addition of a ''pulsing leg'' at the bottom of the column. Pulsing packed column systems not only prevents solids from settling onto packing material but it also increses the number of theoretical stages available for extraction. 3 figs., 2 tabs
Fast multi-dimensional NMR by minimal sampling
Kupče, Ēriks; Freeman, Ray
2008-03-01
A new scheme is proposed for very fast acquisition of three-dimensional NMR spectra based on minimal sampling, instead of the customary step-wise exploration of all of evolution space. The method relies on prior experiments to determine accurate values for the evolving frequencies and intensities from the two-dimensional 'first planes' recorded by setting t1 = 0 or t2 = 0. With this prior knowledge, the entire three-dimensional spectrum can be reconstructed by an additional measurement of the response at a single location (t1∗,t2∗) where t1∗ and t2∗ are fixed values of the evolution times. A key feature is the ability to resolve problems of overlap in the acquisition dimension. Applied to a small protein, agitoxin, the three-dimensional HNCO spectrum is obtained 35 times faster than systematic Cartesian sampling of the evolution domain. The extension to multi-dimensional spectroscopy is outlined.
A multidimensional pseudospectral method for optimal control of quantum ensembles
International Nuclear Information System (INIS)
Ruths, Justin; Li, Jr-Shin
2011-01-01
In our previous work, we have shown that the pseudospectral method is an effective and flexible computation scheme for deriving pulses for optimal control of quantum systems. In practice, however, quantum systems often exhibit variation in the parameters that characterize the system dynamics. This leads us to consider the control of an ensemble (or continuum) of quantum systems indexed by the system parameters that show variation. We cast the design of pulses as an optimal ensemble control problem and demonstrate a multidimensional pseudospectral method with several challenging examples of both closed and open quantum systems from nuclear magnetic resonance spectroscopy in liquid. We give particular attention to the ability to derive experimentally viable pulses of minimum energy or duration.
Effects of Multidimensional Family Therapy (MDFT) on Nonopioid Drug Abuse:
DEFF Research Database (Denmark)
Filges, Trine; Andersen, Ditte; Jørgensen, Anne-Marie Klint
2015-01-01
trials. Meta-analytic methods were used to quantitatively synthesize study results. Results: The search yielded five studies that met inclusion criteria. MDFT was found to be more effective than other treatments on drug abuse problem severity and drug use frequency in the short run but not in the long...... run and demonstrated positive effects on treatment retention compared to control conditions. Discussion: While additional research is needed, the review offers support for MDFT as a treatment to young nonopioid drug abusers. The number of studies included in this review was limited, however......Purpose: This review evaluates the evidence of the effects of multidimensional family therapy (MDFT) on drug use reduction in young people for the treatment of nonopioid drug use. Method: We followed Campbell Collaboration guidelines to conduct a systematic review of randomized and nonrandomized...
Frost Multidimensional Perfectionism Scale: the portuguese version
Directory of Open Access Journals (Sweden)
Ana Paula Monteiro Amaral
2013-01-01
Full Text Available BACKGROUND: The Frost Multidimensional Perfectionism Scale is one of the most world widely used measures of perfectionism. OBJECTIVE: To analyze the psychometric properties of the Portuguese version of the Frost Multidimensional Perfectionism Scale. METHODS: Two hundred and seventeen (178 females students from two Portuguese Universities filled in the scale, and a subgroup (n = 166 completed a retest with a four weeks interval. RESULTS: The scale reliability was good (Cronbach alpha = .857. Corrected item-total correlations ranged from .019 to .548. The scale test-retest reliability suggested a good temporal stability with a test-retest correlation of .765. A principal component analysis with Varimax rotation was performed and based on the Scree plot, two robust factorial structures were found (four and six factors. The principal component analyses, using Monte Carlo PCA for parallel analyses confirmed the six factor solution. The concurrent validity with Hewitt and Flett MPS was high, as well as the discriminant validity of positive and negative affect (Profile of Mood Stats-POMS. DISCUSSION: The two factorial structures (of four and six dimensions of the Portuguese version of Frost Multidimensional Perfectionism Scale replicate the results from different authors, with different samples and cultures. This suggests this scale is a robust instrument to assess perfectionism, in several clinical and research settings as well as in transcultural studies.
Singh, Brajesh K; Srivastava, Vineet K
2015-04-01
The main goal of this paper is to present a new approximate series solution of the multi-dimensional (heat-like) diffusion equation with time-fractional derivative in Caputo form using a semi-analytical approach: fractional-order reduced differential transform method (FRDTM). The efficiency of FRDTM is confirmed by considering four test problems of the multi-dimensional time fractional-order diffusion equation. FRDTM is a very efficient, effective and powerful mathematical tool which provides exact or very close approximate solutions for a wide range of real-world problems arising in engineering and natural sciences, modelled in terms of differential equations.
Energy Technology Data Exchange (ETDEWEB)
Yang, Jin-Hwa [Nuclear Thermal-Hydraulic Engineering Laboratory, Seoul National University, Gwanak 599, Gwanak-ro, Gwanak-gu, Seoul 151-742 (Korea, Republic of); Korea Atomic Energy Research Institute, 989-111, Daedeok-daero, Yuseong-gu, Daejeon 305-600 (Korea, Republic of); Choi, Chi-Jin [Nuclear Thermal-Hydraulic Engineering Laboratory, Seoul National University, Gwanak 599, Gwanak-ro, Gwanak-gu, Seoul 151-742 (Korea, Republic of); Cho, Hyoung-Kyu, E-mail: chohk@snu.ac.kr [Nuclear Thermal-Hydraulic Engineering Laboratory, Seoul National University, Gwanak 599, Gwanak-ro, Gwanak-gu, Seoul 151-742 (Korea, Republic of); Euh, Dong-Jin [Korea Atomic Energy Research Institute, 989-111, Daedeok-daero, Yuseong-gu, Daejeon 305-600 (Korea, Republic of); Park, Goon-Cherl [Nuclear Thermal-Hydraulic Engineering Laboratory, Seoul National University, Gwanak 599, Gwanak-ro, Gwanak-gu, Seoul 151-742 (Korea, Republic of)
2017-02-15
Recently, high precision and high accuracy analysis on multi-dimensional thermal hydraulic phenomena in a nuclear power plant has been considered as state-of-the-art issues. System analysis code, MARS, also adopted a multi-dimensional module to simulate them more accurately. Even though it was applied to represent the multi-dimensional phenomena, but implemented models and correlations in that are one-dimensional empirical ones based on one-dimensional pipe experimental results. Prior to the application of the multi-dimensional simulation tools, however, the constitutive models for a two-phase flow need to be carefully validated, such as the wall friction model. Especially, in a Direct Vessel Injection (DVI) system, the injected emergency core coolant (ECC) on the upper part of the downcomer interacts with the lateral steam flow during the reflood phase in the Large-Break Loss-Of-Coolant-Accident (LBLOCA). The interaction between the falling film and lateral steam flow induces a multi-dimensional two-phase flow. The prediction of ECC flow behavior plays a key role in determining the amount of coolant that can be used as core cooling. Therefore, the wall friction model which is implemented to simulate the multi-dimensional phenomena should be assessed by multidimensional experimental results. In this paper, the air–water cross film flow experiments simulating the multi-dimensional phenomenon in upper part of downcomer as a conceptual problem will be introduced. The two-dimensional local liquid film velocity and thickness data were used as benchmark data for code assessment. And then the previous wall friction model of the MARS-MultiD in the annular flow regime was modified. As a result, the modified MARS-MultiD produced improved calculation result than previous one.
The P.E.A.C.E. Pack: A Computerized Online Assessment of School Bullying
Slee, Phillip T.; Mohyla, Jury
2014-01-01
School bullying is an international problem with harmful outcomes for those involved. This study describes the design and field testing of an innovative computer-based social learning tool for assessing student perceptions of bullying developed for an Australian intervention program called the P.E.A.C.E. Pack. Students rate their peer group…
Column-to-column packing variation of disposable pre-packed columns for protein chromatography.
Schweiger, Susanne; Hinterberger, Stephan; Jungbauer, Alois
2017-12-08
In the biopharmaceutical industry, pre-packed columns are the standard for process development, but they must be qualified before use in experimental studies to confirm the required performance of the packed bed. Column qualification is commonly done by pulse response experiments and depends highly on the experimental testing conditions. Additionally, the peak analysis method, the variation in the 3D packing structure of the bed, and the measurement precision of the workstation influence the outcome of qualification runs. While a full body of literature on these factors is available for HPLC columns, no comparable studies exist for preparative columns for protein chromatography. We quantified the influence of these parameters for commercially available pre-packed and self-packed columns of disposable and non-disposable design. Pulse response experiments were performed on 105 preparative chromatography columns with volumes of 0.2-20ml. The analyte acetone was studied at six different superficial velocities (30, 60, 100, 150, 250 and 500cm/h). The column-to-column packing variation between disposable pre-packed columns of different diameter-length combinations varied by 10-15%, which was acceptable for the intended use. The column-to-column variation cannot be explained by the packing density, but is interpreted as a difference in particle arrangement in the column. Since it was possible to determine differences in the column-to-column performance, we concluded that the columns were well-packed. The measurement precision of the chromatography workstation was independent of the column volume and was in a range of±0.01ml for the first peak moment and±0.007 ml 2 for the second moment. The measurement precision must be considered for small columns in the range of 2ml or less. The efficiency of disposable pre-packed columns was equal or better than that of self-packed columns. Copyright © 2017 The Author(s). Published by Elsevier B.V. All rights reserved.
Experimental studies on the coolability of packed beds. Flooding of hot dry packed beds
International Nuclear Information System (INIS)
Leininger, S.; Kulenovic, R.; Laurien, E.
2013-01-01
In case of a severe accident in a nuclear power plant meltdown of the reactor core can occur and form a packed bed in the lower plenum of the reactor pressure vessel (RPV) after solidification due to contact with water. The removal of after-heat and the long-term coolability is of essential interest. The efficient injection of cooling water into the packed bed has to be assured without endangering the structural integrity of the reactor pressure vessel. The experiments performed aimed to study the dry-out and the quenching (flooding) of hot dry packed beds. Two different inflow variants, bottom- and top-flooding including the variation of the starting temperature of the packed bed and the injection rate were studied. In case of bottom flooding the quenching time increases with increasing packed bed temperature and decreasing injection rate. In case of top flooding the flow pattern is more complex, in a first phase the water flows preferentially toward the RPV wall, the flow paths conduct the water downwards. The flow resistance of the packed bed increases with increasing bed temperatures. The quenching temperatures increase significantly above average.
Heavy metals in the snow pack of Semey town
International Nuclear Information System (INIS)
Panin, M.S.; Esenzholova, A.Zh.; Toropov, A.S.
2008-01-01
The data about the maintenance of heavy metals in the snow pack in various zones of Semey and biogeochemical operation factors of snow pack in Semey are presented in this work. Also the correlation connection between elements is calculated.
Evaluation of Packed Distillation Columns I - Atmospheric Pressure
National Research Council Canada - National Science Library
Reynolds, Thaine
1951-01-01
.... Four column-packing combinations of the glass columns and four column-packing combinations of the steel columns were investigated at atmospheric pressure using a test mixture of methylcyclohexane...
Microbiological Quality of Blister Pack Tablets in Community ...
African Journals Online (AJOL)
Keywords: Blister pack, Community pharmacy, Good Manufacturing Practice, Microbial contamination,. Quality control ... High levels of microbial contamination in blister-packed tablets ... and their drugs approved by the Jordan Food and Drug ...
Packing of equal discs on a parabolic spiral lattice
International Nuclear Information System (INIS)
Xudong, F.; Bursill, L.A.; Julin, P.
1989-01-01
A contact disc model is investigated to determine the most closely-packed parabolic spiral lattice. The most space-efficient packings have divergence angles in agreement with the priority ranking of natural spiral structures
On fully multidimensional and high order non oscillatory finite volume methods, I
International Nuclear Information System (INIS)
Lafon, F.
1992-11-01
A fully multidimensional flux formulation for solving nonlinear conservation laws of hyperbolic type is introduced to perform calculations on unstructured grids made of triangular or quadrangular cells. Fluxes are computed across dual median cells with a multidimensional 2D Riemann Solver (R2D Solver) whose intermediate states depend on either a three (on triangle R2DT solver) of four (on quadrangle, R2DQ solver) state solutions prescribed on the three or four sides of a gravity cell. Approximate Riemann solutions are computed via a linearization process of Roe's type involving multidimensional effects. Moreover, a monotonous scheme using stencil and central Lax-Friedrichs corrections on sonic curves are built in. Finally, high order accurate ENO-like (Essentially Non Oscillatory) reconstructions using plane and higher degree polynomial limitations are defined in the set up of finite element Lagrange spaces P k and Q k for k≥0, on triangles and quadrangles, respectively. Numerical experiments involving both linear and nonlinear conservation laws to be solved on unstructured grids indicate the ability of our techniques when dealing with strong multidimensional effects. An application to Euler's equations for the Mach three step problem illustrates the robustness and usefulness of our techniques using triangular and quadrangular grids. (Author). 33 refs., 13 figs
On simplified application of multidimensional Savitzky-Golay filters and differentiators
Shekhar, Chandra
2016-02-01
I propose a simplified approach for multidimensional Savitzky-Golay filtering, to enable its fast and easy implementation in scientific and engineering applications. The proposed method, which is derived from a generalized framework laid out by Thornley (D. J. Thornley, "Novel anisotropic multidimensional convolution filters for derivative estimation and reconstruction" in Proceedings of International Conference on Signal Processing and Communications, November 2007), first transforms any given multidimensional problem into a unique one, by transforming coordinates of the sampled data nodes to unity-spaced, uniform data nodes, and then performs filtering and calculates partial derivatives on the unity-spaced nodes. It is followed by transporting the calculated derivatives back onto the original data nodes by using the chain rule of differentiation. The burden to performing the most cumbersome task, which is to carry out the filtering and to obtain derivatives on the unity-spaced nodes, is almost eliminated by providing convolution coefficients for a number of convolution kernel sizes and polynomial orders, up to four spatial dimensions. With the availability of the convolution coefficients, the task of filtering at a data node reduces merely to multiplication of two known matrices. Simplified strategies to adequately address near-boundary data nodes and to calculate partial derivatives there are also proposed. Finally, the proposed methodologies are applied to a three-dimensional experimentally obtained data set, which shows that multidimensional Savitzky-Golay filters and differentiators perform well in both the internal and the near-boundary regions of the domain.
Multidimensional periodic Schrödinger operator perturbation theory and applications
Veliev, Oktay
2015-01-01
The book describes the direct problems and the inverse problem of the multidimensional Schrödinger operator with a periodic potential. This concerns perturbation theory and constructive determination of the spectral invariants and finding the periodic potential from the given Bloch eigenvalues. The unique method of this book derives the asymptotic formulas for Bloch eigenvalues and Bloch functions for arbitrary dimension. Moreover, the measure of the iso-energetic surfaces in the high energy region is construct and estimated. It implies the validity of the Bethe-Sommerfeld conjecture for arbitrary dimensions and arbitrary lattices. Using the perturbation theory constructed in this book, the spectral invariants of the multidimensional operator from the given Bloch eigenvalues are determined. Some of these invariants are explicitly expressed by the Fourier coefficients of the potential. This way the possibility to determine the potential constructively by using Bloch eigenvalues as input data is given. In the ...
Imaging of drug smuggling by body packing.
Sica, Giacomo; Guida, Franco; Bocchini, Giorgio; Iaselli, Francesco; Iadevito, Isabella; Scaglione, Mariano
2015-02-01
Body packing, pushing, and stuffing are hazardous practices with complex medicolegal and social implications. A radiologist plays both a social and a medicolegal role in their assessment, and it should not be limited only to the identification of the packages but must also provide accurate information about their number and their exact location so as to prevent any package remains in the body packer. Radiologists must also be able to recognize the complications associated with these risky practices. Imaging assessment of body packing is performed essentially through plain abdominal X-ray and computed tomography scans. Ultrasound and magnetic resonance imaging, although with some advantages, actually have a limited use. Copyright © 2014 Elsevier Inc. All rights reserved.
Packing and Disorder in Substituted Fullerenes
Tummala, Naga Rajesh
2016-07-15
Fullerenes are ubiquitous as electron-acceptor and electron-transport materials in organic solar cells. Recent synthetic strategies to improve the solubility and electronic characteristics of these molecules have translated into a tremendous increase in the variety of derivatives employed in these applications. Here, we use molecular dynamics (MD) simulations to examine the impact of going from mono-adducts to bis- and tris-adducts on the structural, cohesive, and packing characteristics of [6,6]-phenyl-C60-butyric acid methyl ester (PCBM) and indene-C60. The packing configurations obtained at the MD level then serve as input for density functional theory calculations that examine the solid-state energetic disorder (distribution of site energies) as a function of chemical substitution. The variations in structural and site-energy disorders reflect the fundamental materials differences among the derivatives and impact the performance of these materials in thin-film electronic devices.
Homometrism in close-packed structures
International Nuclear Information System (INIS)
Mardix, S.
1990-01-01
Homometric structures are non-congruent structures having identical X-ray intensity distributions. It has so far been assumed that such structures, while theoretically interesting, would not be realized in practice. Homometrism in close-packed structures is shown to be a realistic possibility. Some general rules applicable to homometric pairs are presented; it is shown that an infinite number of them can be derived from one-dimensional homometric pairs. An exhaustive search of close-packed structures with periods of up to 26 reveals that the smallest period of a homometric pair is 15 and that their number increases rapidly with the period. Homometrism in polytypic structures is further discussed. (orig.)
School meal sociality or lunch pack individualism?
DEFF Research Database (Denmark)
Andersen, Sidse Schoubye; Holm, Lotte; Baarts, Charlotte
2015-01-01
the social life of a school class, and how these arrangements involve strategies of both inclusion and exclusion. Two types of school meals are compared in the intervention study: a hot meal based on Nordic ingredients and the normal Danish school meal arrangement in which children bring lunch packs...... to school. The study discusses commensality by examining and comparing lunchtime interactions within the same group of children in the two contrasting meal situations. The results fail to confirm the conventional view that shared meals have greater social impacts and benefits than eating individualized...... foods. The article argues that the social entrepreneurship involved in sharing individual lunch packs might even outweigh some of the benefits of shared meals where everyone is served the same food....
36 CFR 1002.16 - Horses and pack animals.
2010-07-01
... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Horses and pack animals. 1002... AND RECREATION § 1002.16 Horses and pack animals. The following are prohibited: (a) The use of animals other than those designated as “pack animals” for purposes of transporting equipment. (b) The use of...
36 CFR 34.10 - Saddle and pack animals.
2010-07-01
... 36 Parks, Forests, and Public Property 1 2010-07-01 2010-07-01 false Saddle and pack animals. 34... INTERIOR EL PORTAL ADMINISTRATIVE SITE REGULATIONS § 34.10 Saddle and pack animals. The use of saddle and pack animals is prohibited without a permit from the Superintendent. ...
36 CFR 2.16 - Horses and pack animals.
2010-07-01
... 36 Parks, Forests, and Public Property 1 2010-07-01 2010-07-01 false Horses and pack animals. 2.16... RESOURCE PROTECTION, PUBLIC USE AND RECREATION § 2.16 Horses and pack animals. The following are prohibited: (a) The use of animals other than those designated as “pack animals” for purposes of transporting...
New Structured Packing CUB for Purification of Exhaust Gases
Directory of Open Access Journals (Sweden)
Irina Novikova
2016-10-01
Full Text Available New structured packing for heat and mass transfer processes named CUB is presented in our article. The packing can be applied in packed towers for exhaust gas cleaning instead random packing, for example, rings type that are the most used in such processes. The advantages of the new packing over random packing are lower pressure drop, capability of purification and as a consequence long-term service of the packing. The researches of intensity of liquid-phase mass-transfer in packed bed depending on liquid spray rate and gas velocity were carried out. Obtained data show that packing CUB is more effective than the most popular type of structured packing under all other conditions being equal. As experimental data shown heat transfer coefficient was up by 17% and mass transfer coefficient was up by 51%. We found out optimal geometry of cross section of the new packing, namely, number of elements and parameters of one element. The new construction of structured packing is applicable for both type of column cross-section round and square.
Packing parameters effect on injection molding of polypropylene nanostructured surfaces
DEFF Research Database (Denmark)
Calaon, Matteo; Tosello, Guido; Hansen, Hans Nørgaard
2012-01-01
having a diameter of 500 nm was employed. The tool insert surface was produced using chemical-based-batch techniques such aluminum anodization and nickel electroplating. During the injection molding process, polypropylene (PP) was employed as material and packing phase parameters (packing time, packing...
Evaluation of Type II Fast Packs for Electrostatic Discharge Properties.
1983-08-01
34 x 8" x 1 3/4") consisting of a reclosable cushioned carrier which mates into an outer fiberboard sleeve. A cushioning insert is used consisting of a... RECLOSABLE CUSHIONED CARRIER TEST LOAD FIGURE 1: Cancel Caddy Pack * CONVOLUTED 4* CUSHIONED I FIGURE 2: Type II Fast Pack (PPP-B-1672) TYPE II FAST PACK
21 CFR 133.124 - Cold-pack cheese food.
2010-04-01
... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Cold-pack cheese food. 133.124 Section 133.124 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD... Cheese and Related Products § 133.124 Cold-pack cheese food. (a)(1) Cold-pack cheese food is the food...
CoolPack – Simulation tools for refrigeration systems
DEFF Research Database (Denmark)
Jakobsen, Arne; Rasmussen, Bjarne D.; Andersen, Simon Engedal
1999-01-01
CoolPack is a collection of programs used for energy analysis and optimisation of refrigeration systems. CoolPack is developed at the Department of Energy Engineering at the Technical University of Denmark. The Danish Energy Agency finances the project. CoolPack is freeware and can be downloaded...
48 CFR 552.211-87 - Export packing.
2010-10-01
... 48 Federal Acquisition Regulations System 4 2010-10-01 2010-10-01 false Export packing. 552.211-87... FORMS SOLICITATION PROVISIONS AND CONTRACT CLAUSES Text of Provisions and Clauses 552.211-87 Export packing. As prescribed in 511.204(b)(7), insert the following clause: Export Packing (JAN 2010) (a...
The emergence and evolution of the multidimensional organization
Strikwerda, J.; Stoelhorst, J.W.
2009-01-01
The article discusses multidimensional organizations and the evolution of complex organizations. The six characteristics of multidimensional organizations, disadvantages of the successful organizational structure that is categorized as a multidivisional, multi-unit or M-form, research by the Foundation for Management Studies which suggests that synergies across business divisions can be exploited by the M-form, a team approach to creating economic value, examples of multidimensional firms suc...
An Improved Multidimensional MPA Procedure for Bidirectional Earthquake Excitations
Wang, Feng; Sun, Jian-Gang; Zhang, Ning
2014-01-01
Presently, the modal pushover analysis procedure is extended to multidimensional analysis of structures subjected to multidimensional earthquake excitations. an improved multidimensional modal pushover analysis (IMMPA) method is presented in the paper in order to estimate the response demands of structures subjected to bidirectional earthquake excitations, in which the unidirectional earthquake excitation applied on equivalent SDOF system is replaced by the direct superposition of two compone...
Symmetric scrolled packings of multilayered carbon nanoribbons
Savin, A. V.; Korznikova, E. A.; Lobzenko, I. P.; Baimova, Yu. A.; Dmitriev, S. V.
2016-06-01
Scrolled packings of single-layer and multilayer graphene can be used for the creation of supercapacitors, nanopumps, nanofilters, and other nanodevices. The full atomistic simulation of graphene scrolls is restricted to consideration of relatively small systems in small time intervals. To overcome this difficulty, a two-dimensional chain model making possible an efficient calculation of static and dynamic characteristics of nanoribbon scrolls with allowance for the longitudinal and bending stiffness of nanoribbons is proposed. The model is extended to the case of scrolls of multilayer graphene. Possible equilibrium states of symmetric scrolls of multilayer carbon nanotribbons rolled up so that all nanoribbons in the scroll are equivalent are found. Dependences of the number of coils, the inner and outer radii, lowest vibrational eigenfrequencies of rolled packages on the length L of nanoribbons are obtained. It is shown that the lowest vibrational eigenfrequency of a symmetric scroll decreases with a nanoribbon length proportionally to L -1. It is energetically unfavorable for too short nanoribbons to roll up, and their ground state is a stack of plane nanoribbons. With an increasing number k of layers, the nanoribbon length L necessary for creation of symmetric scrolls increases. For a sufficiently small number of layers k and a sufficiently large nanoribbon length L, the scrolled packing has the lowest energy as compared to that of stack of plane nanoribbons and folded structures. The results can be used for development of nanomaterials and nanodevices on the basis of graphene scrolled packings.
Anku, Sitsofe E.
1997-09-01
Using the reform documents of the National Council of Teachers of Mathematics (NCTM) (NCTM, 1989, 1991, 1995), a theory-based multi-dimensional assessment framework (the "SEA" framework) which should help expand the scope of assessment in mathematics is proposed. This framework uses a context based on mathematical reasoning and has components that comprise mathematical concepts, mathematical procedures, mathematical communication, mathematical problem solving, and mathematical disposition.
DEFF Research Database (Denmark)
Sengupta, Mita Eva; Thapa, Sundar; Thamsborg, Stig Milan
2016-01-01
Strongyle eggs of helminths of livestock usually hatch within a few hours or days after deposition with faeces. This poses a problem when faecal sampling is performed in the field. As oxygen is needed for embryonic development, it is recommended to reduce air supply during transport and refrigerate....... The present study therefore investigated the combined effect of vacuum packing and temperature on survival of strongyle eggs and their subsequent ability to hatch and develop into L3. Fresh faecal samples were collected from calves infected with Cooperia oncophora, pigs infected with Oesophagostomum dentatum......, and horses infected with Strongylus vulgaris and cyathostomins. The samples were allocated into four treatments: vacuum packing and storage at 5 °C or 20 °C (5 V and 20 V); normal packing in plastic gloves closed with a loose knot and storage at 5 °C or 20 °C (5 N and 20 N). The number of eggs per gram...
Multidimensional Risk Management for Underground Electricity Networks
Directory of Open Access Journals (Sweden)
Garcez Thalles V.
2014-08-01
Full Text Available In the paper we consider an electricity provider company that makes decision on allocating resources on electric network maintenance. The investments decrease malfunction rate of network nodes. An accidental event (explosion, fire, etc. or a malfunctioning on underground system can have various consequences and in different perspectives, such as deaths and injuries of pedestrians, fires in nearby locations, disturbances in the flow of vehicular traffic, loss to the company image, operating and financial losses, etc. For this reason it is necessary to apply an approach of the risk management that considers the multidimensional view of the consequences. Furthermore an analysis of decision making should consider network dependencies between the nodes of the electricity distribution system. In the paper we propose the use of the simulation to assess the network effects (such as the increase of the probability of other accidental event and the occurrence of blackouts of the dependent nodes in the multidimensional risk assessment in electricity grid. The analyzed effects include node overloading due to malfunction of adjacent nodes and blackouts that take place where there is temporarily no path in the grid between the power plant and a node. The simulation results show that network effects have crucial role for decisions in the network maintenance – outcomes of decisions to repair a particular node in the network can have significant influence on performance of other nodes. However, those dependencies are non-linear. The effects of network connectivity (number of connections between nodes on its multidimensional performance assessment depend heavily on the overloading effect level. The simulation results do not depend on network type structure (random or small world – however simulation outcomes for random networks have shown higher variance compared to small-world networks.
Trust and credibility: measured by multidimensional scaling
International Nuclear Information System (INIS)
Warg, L.E.; Bodin, L.
1998-01-01
Full text of publication follows: in focus of much of today's research interest in risk communication, is the fact that the communities do not trust policy and decision makers such as politicians, government or industry people. This is especially serious in the years to come when we are expecting risk issues concerning for example the nuclear industry, global warming and hazardous waste, to be even higher on the political and social agenda all over the world. Despite the research efforts devoted to trust, society needs an in depth understanding of trust for conducting successful communication regarding environmental hazards. The present abstract is about an experimental study in psychology where focus has been on the possibility to use the multidimensional scaling technique to explore the characteristics people consider to be of importance when they say that certain persons are credible. In the study, a total of 61 students of the University of Oerebro, Sweden, were required to make comparisons of the similarity between 12 well-known swedish persons from politics science, media, industry, 'TV-world' and literature (two persons at a time), regarding their credibility when making statements about risks in society. In addition, the subjects were rating the importance of 19 factors for the credibility of a source. These 61 persons comprised three groups of students: pedagogists, business economists, and chemists. There were 61 % women and 39% men and the mean age was 23 years. The results will be analyzed using multidimensional scaling technique. Differences between the three groups will be analyzed and presented as well as those between men and women. In addition, the 19 factors will be discussed and considered when trying to label the dimensions accounted for by the multidimensional scaling technique. The result from this study will contribute to our understanding of important factors behind human judgments concerning trust and credibility. It will also point to a
Multidimensional flux-limited advection schemes
International Nuclear Information System (INIS)
Thuburn, J.
1996-01-01
A general method for building multidimensional shape preserving advection schemes using flux limiters is presented. The method works for advected passive scalars in either compressible or incompressible flow and on arbitrary grids. With a minor modification it can be applied to the equation for fluid density. Schemes using the simplest form of the flux limiter can cause distortion of the advected profile, particularly sideways spreading, depending on the orientation of the flow relative to the grid. This is partly because the simple limiter is too restrictive. However, some straightforward refinements lead to a shape-preserving scheme that gives satisfactory results, with negligible grid-flow angle-dependent distortion
Point Information Gain and Multidimensional Data Analysis
Directory of Open Access Journals (Sweden)
Renata Rychtáriková
2016-10-01
Full Text Available We generalize the point information gain (PIG and derived quantities, i.e., point information gain entropy (PIE and point information gain entropy density (PIED, for the case of the Rényi entropy and simulate the behavior of PIG for typical distributions. We also use these methods for the analysis of multidimensional datasets. We demonstrate the main properties of PIE/PIED spectra for the real data with the examples of several images and discuss further possible utilizations in other fields of data processing.
A real-time insulation detection method for battery packs used in electric vehicles
Tian, Jiaqiang; Wang, Yujie; Yang, Duo; Zhang, Xu; Chen, Zonghai
2018-05-01
Due to the energy crisis and environmental pollution, electric vehicles have become more and more popular. Compared to traditional fuel vehicles, the electric vehicles are integrated with more high-voltage components, which have potential security risks of insulation. The insulation resistance between the chassis and the direct current bus of the battery pack is easily affected by factors such as temperature, humidity and vibration. In order to ensure the safe and reliable operation of the electric vehicles, it is necessary to detect the insulation resistance of the battery pack. This paper proposes an insulation detection scheme based on low-frequency signal injection method. Considering the insulation detector which can be easily affected by noises, the algorithm based on Kalman filter is proposed. Moreover, the battery pack is always in the states of charging and discharging during driving, which will lead to frequent changes in the voltage of the battery pack and affect the estimation accuracy of insulation detector. Therefore the recursive least squares algorithm is adopted to solve the problem that the detection results of insulation detector mutate with the voltage of the battery pack. The performance of the proposed method is verified by dynamic and static experiments.
New raw materials improve packing sealing efficiency
International Nuclear Information System (INIS)
Igel, B.; McKeague, L.
2012-01-01
End-users and OEM's using or manufacturing on/off and control valves expect a permanent and effective increase in service life together with an increased sealing capability while at the same time minimizing maintenance concerns. Developing materials which provide consistency and repeatability are essential characteristics to optimizing valve performance. “New Generation” materials and yarn allow us to meet this growing demand while complying with the requirements related to chemical purity and an increased level of safety to both plant workers and equipment in the nuclear environment. Through R&D initiatives and developments in new and improved raw materials; a new mechanical packing generation which optimizes friction coefficients and extended life cycle has been introduced to the industry. Lower friction values drastically optimize actuator effort and size improving efficiency for stem operation with significant improvements in flow control of fluids. Combined with new and improved procedures (installation, torque levels and consolidation recommendations), this new packing generation has provided significant improvement in the mechanical behavior of packing materials (independent tests carried out in collaboration with AECL and CETIM) this has provided the opportunity to develop successful Valve Enhancement Programs which offer improved efficiency, valve operation and repeatability. These NEW generation yarns are available with or without wire reinforcement depending on specific operating parameters and conditions. The purpose of this presentation is to demonstrate that new generation material(s). Which are available to the industry for AOV, MOV and Manual valves? - To highlight the steps taken in R&D and manufacturing contributing to the much improved yarns and finished packing products. - Comply and are designed to meet the stringent requirements in the nuclear industry - Simplify valve maintenance without risk to safety or performance - Increase service
The mechanical behaviour of packed particulates
International Nuclear Information System (INIS)
Dutton, R.
1998-01-01
Within the Canadian Nuclear Fuel Waste Management program, the central concept is to package used fuel in containers that would be deposited in an underground vault in a plutonic rock formation. To provide internal mechanical support for the container, the reference design specifies it to be filled with a matrix of compacted particulate material (called 'packed particulate'), such as quartz sand granules. The focus of this report is on the mechanical properties of the packed-particulate material, based on information drawn from the extant literature. We first consider the packing density of particulate matrices to minimize the remnant porosity and maximize mechanical stability under conditions of external pressure. Practical methods, involving vibratory packing, are reviewed and recommendations made to select techniques to achieve optimum packing density. The behaviour of particulates under compressive loading has been of interest to the powder metallurgy industry (i.e., the manufacture of products from pressed/sintered metal and ceramic powders) since the early decades of this century. We review the evidence showing that in short timescales, stress induced compaction occurs by particle shuffling and rearrangement, elastic distortion, plastic yielding and microfracturing. Analytical expressions are available to describe these processes in a semiquantitative fashion. Time-dependent compaction, mainly via creep mechanisms, is more complex. Much of the theoretical and experimental information is confined to higher temperatures (> 500 degrees C), where deformation rates are more rapid. Thus, for the relatively low ambient temperatures of the waste container (∼100 degrees C), we require analytical techniques to extrapolate the collective particulate creep behaviour. This is largely accomplished by employing current theories of creep deformation, particularly in the form of Deformation Mechanism Maps, which allow estimation of creep rates over a wide range of stress
The mechanical behaviour of packed particulates
Energy Technology Data Exchange (ETDEWEB)
Dutton, R
1998-01-01
Within the Canadian Nuclear Fuel Waste Management program, the central concept is to package used fuel in containers that would be deposited in an underground vault in a plutonic rock formation. To provide internal mechanical support for the container, the reference design specifies it to be filled with a matrix of compacted particulate material (called 'packed particulate'), such as quartz sand granules. The focus of this report is on the mechanical properties of the packed-particulate material, based on information drawn from the extant literature. We first consider the packing density of particulate matrices to minimize the remnant porosity and maximize mechanical stability under conditions of external pressure. Practical methods, involving vibratory packing, are reviewed and recommendations made to select techniques to achieve optimum packing density. The behaviour of particulates under compressive loading has been of interest to the powder metallurgy industry (i.e., the manufacture of products from pressed/sintered metal and ceramic powders) since the early decades of this century. We review the evidence showing that in short timescales, stress induced compaction occurs by particle shuffling and rearrangement, elastic distortion, plastic yielding and microfracturing. Analytical expressions are available to describe these processes in a semiquantitative fashion. Time-dependent compaction, mainly via creep mechanisms, is more complex. Much of the theoretical and experimental information is confined to higher temperatures (> 500 degrees C), where deformation rates are more rapid. Thus, for the relatively low ambient temperatures of the waste container ({approx}100 degrees C), we require analytical techniques to extrapolate the collective particulate creep behaviour. This is largely accomplished by employing current theories of creep deformation, particularly in the form of Deformation Mechanism Maps, which allow estimation of creep rates over a wide
HETP evaluation of structured packing distillation column
Directory of Open Access Journals (Sweden)
A. E. Orlando Jr.
2009-09-01
Full Text Available Several tests with a hydrocarbon mixture of known composition (C8-C14, obtained from DETEN Chemistry S.A., have been performed in a laboratory distillation column, having 40mm of nominal diameter and 2.2m high, with internals of Sulzer DX gauze stainless steel structured packing. The main purpose of this work was to evaluate HETP of a structured packing laboratory scale distillation column, operating continuously. Six HETP correlations available in the literature were compared in order to find out which is the most appropriate for structured packing columns working with medium distillates. Prior to the experimental tests, simulation studies using commercial software PRO/II® were performed in order to establish the optimum operational conditions for the distillation, especially concerning operating pressure, top and bottom temperatures, feed location and reflux ratio. The results of PRO/II® were very similar to the analysis of the products obtained during continuous operation, therefore permitting the use of the properties calculated by that software on the theoretical models investigated. The theoretical models chosen for HETP evaluation were: Bravo, Rocha and Fair (1985; Rocha, Bravo and Fair (1993, 1996; Brunazzi and Pagliant (1997; Carlo, Olujić and Pagliant (2006; Olujić et al., (2004. Modifications concerning calculation of specific areas were performed on the correlations in order to fit them for gauze packing HETP evaluation. As the laboratory distillation column was operated continuously, different HETP values were found by the models investigated for each section of the column. The low liquid flow rates in the top section of the column are a source of error for HETP evaluation by the models; therefore, more reliable HETP values were found in the bottom section, in which liquid flow rates were much greater. Among the theoretical models, Olujić et al. (2004 has shown good results relative to the experimental tests. In addition, the
MULTIDIMENSIONAL MODELING OF CORONAL RAIN DYNAMICS
Energy Technology Data Exchange (ETDEWEB)
Fang, X.; Xia, C.; Keppens, R. [Centre for mathematical Plasma Astrophysics, Department of Mathematics, KU Leuven, B-3001 Leuven (Belgium)
2013-07-10
We present the first multidimensional, magnetohydrodynamic simulations that capture the initial formation and long-term sustainment of the enigmatic coronal rain phenomenon. We demonstrate how thermal instability can induce a spectacular display of in situ forming blob-like condensations which then start their intimate ballet on top of initially linear force-free arcades. Our magnetic arcades host a chromospheric, transition region, and coronal plasma. Following coronal rain dynamics for over 80 minutes of physical time, we collect enough statistics to quantify blob widths, lengths, velocity distributions, and other characteristics which directly match modern observational knowledge. Our virtual coronal rain displays the deformation of blobs into V-shaped features, interactions of blobs due to mostly pressure-mediated levitations, and gives the first views of blobs that evaporate in situ or are siphoned over the apex of the background arcade. Our simulations pave the way for systematic surveys of coronal rain showers in true multidimensional settings to connect parameterized heating prescriptions with rain statistics, ultimately allowing us to quantify the coronal heating input.
Multidimensional Learner Model In Intelligent Learning System
Deliyska, B.; Rozeva, A.
2009-11-01
The learner model in an intelligent learning system (ILS) has to ensure the personalization (individualization) and the adaptability of e-learning in an online learner-centered environment. ILS is a distributed e-learning system whose modules can be independent and located in different nodes (servers) on the Web. This kind of e-learning is achieved through the resources of the Semantic Web and is designed and developed around a course, group of courses or specialty. An essential part of ILS is learner model database which contains structured data about learner profile and temporal status in the learning process of one or more courses. In the paper a learner model position in ILS is considered and a relational database is designed from learner's domain ontology. Multidimensional modeling agent for the source database is designed and resultant learner data cube is presented. Agent's modules are proposed with corresponding algorithms and procedures. Multidimensional (OLAP) analysis guidelines on the resultant learner module for designing dynamic learning strategy have been highlighted.
Multidimensional biochemical information processing of dynamical patterns.
Hasegawa, Yoshihiko
2018-02-01
Cells receive signaling molecules by receptors and relay information via sensory networks so that they can respond properly depending on the type of signal. Recent studies have shown that cells can extract multidimensional information from dynamical concentration patterns of signaling molecules. We herein study how biochemical systems can process multidimensional information embedded in dynamical patterns. We model the decoding networks by linear response functions, and optimize the functions with the calculus of variations to maximize the mutual information between patterns and output. We find that, when the noise intensity is lower, decoders with different linear response functions, i.e., distinct decoders, can extract much information. However, when the noise intensity is higher, distinct decoders do not provide the maximum amount of information. This indicates that, when transmitting information by dynamical patterns, embedding information in multiple patterns is not optimal when the noise intensity is very large. Furthermore, we explore the biochemical implementations of these decoders using control theory and demonstrate that these decoders can be implemented biochemically through the modification of cascade-type networks, which are prevalent in actual signaling pathways.
MULTIDIMENSIONAL MODELING OF CORONAL RAIN DYNAMICS
International Nuclear Information System (INIS)
Fang, X.; Xia, C.; Keppens, R.
2013-01-01
We present the first multidimensional, magnetohydrodynamic simulations that capture the initial formation and long-term sustainment of the enigmatic coronal rain phenomenon. We demonstrate how thermal instability can induce a spectacular display of in situ forming blob-like condensations which then start their intimate ballet on top of initially linear force-free arcades. Our magnetic arcades host a chromospheric, transition region, and coronal plasma. Following coronal rain dynamics for over 80 minutes of physical time, we collect enough statistics to quantify blob widths, lengths, velocity distributions, and other characteristics which directly match modern observational knowledge. Our virtual coronal rain displays the deformation of blobs into V-shaped features, interactions of blobs due to mostly pressure-mediated levitations, and gives the first views of blobs that evaporate in situ or are siphoned over the apex of the background arcade. Our simulations pave the way for systematic surveys of coronal rain showers in true multidimensional settings to connect parameterized heating prescriptions with rain statistics, ultimately allowing us to quantify the coronal heating input.
A Multidimensional Theory of Suicide.
Leenaars, Antoon A; Dieserud, Gudrun; Wenckstern, Susanne; Dyregrov, Kari; Lester, David; Lyke, Jennifer
2018-04-05
Theory is the foundation of science; this is true in suicidology. Over decades of studies of suicide notes, Leenaars developed a multidimensional model of suicide, with international (crosscultural) studies and independent verification. To corroborate Leenaars's theory with a psychological autopsy (PA) study, examining age and sex of the decedent, and survivor's relationship to deceased. A PA study in Norway, with 120 survivors/informants was undertaken. Leenaars' theoretical-conceptual (protocol) analysis was undertaken of the survivors' narratives and in-depth interviews combined. Substantial interjudge reliability was noted (κ = .632). Overall, there was considerable confirmatory evidence of Leenaars's intrapsychic and interpersonal factors in suicide survivors' narratives. Differences were found in the age of the decedent, but not in sex, nor in the survivor's closeness of the relationship. Older deceased people were perceived to exhibit more heightened unbearable intrapsychic pain, associated with the suicide. Leenaars's theory has corroborative verification, through the decedents' suicide notes and the survivors' narratives. However, the multidimensional model needs further testing to develop a better evidence-based way of understanding suicide.
Structural characterization of the packings of granular regular polygons.
Wang, Chuncheng; Dong, Kejun; Yu, Aibing
2015-12-01
By using a recently developed method for discrete modeling of nonspherical particles, we simulate the random packings of granular regular polygons with three to 11 edges under gravity. The effects of shape and friction on the packing structures are investigated by various structural parameters, including packing fraction, the radial distribution function, coordination number, Voronoi tessellation, and bond-orientational order. We find that packing fraction is generally higher for geometrically nonfrustrated regular polygons, and can be increased by the increase of edge number and decrease of friction. The changes of packing fraction are linked with those of the microstructures, such as the variations of the translational and orientational orders and local configurations. In particular, the free areas of Voronoi tessellations (which are related to local packing fractions) can be described by log-normal distributions for all polygons. The quantitative analyses establish a clearer picture for the packings of regular polygons.
Perceptual Dominant Color Extraction by Multidimensional Particle Swarm Optimization
Directory of Open Access Journals (Sweden)
Moncef Gabbouj
2009-01-01
Full Text Available Color is the major source of information widely used in image analysis and content-based retrieval. Extracting dominant colors that are prominent in a visual scenery is of utmost importance since the human visual system primarily uses them for perception and similarity judgment. In this paper, we address dominant color extraction as a dynamic clustering problem and use techniques based on Particle Swarm Optimization (PSO for finding optimal (number of dominant colors in a given color space, distance metric and a proper validity index function. The first technique, so-called Multidimensional (MD PSO can seek both positional and dimensional optima. Nevertheless, MD PSO is still susceptible to premature convergence due to lack of divergence. To address this problem we then apply Fractional Global Best Formation (FGBF technique. In order to extract perceptually important colors and to further improve the discrimination factor for a better clustering performance, an efficient color distance metric, which uses a fuzzy model for computing color (dis- similarities over HSV (or HSL color space is proposed. The comparative evaluations against MPEG-7 dominant color descriptor show the superiority of the proposed technique.
Analytical solution to the coupled evolution of multidimensional NMR data
International Nuclear Information System (INIS)
Mueller, Geoffrey A.
2009-01-01
A substantial time savings in the collection of multidimensional NMR data can be achieved by coupling the evolution of nuclei in the indirect dimensions. In order to save time, the sampling of the indirect dimensions is inherently incomplete. Therefore, many algorithms and samplings schemes have been developed aimed at separating the coevolved frequencies into analyzable data with limited artifacts. This paper extends the use of circulant matrices to describe coupled evolution with convolutions. By understanding the data in terms of convolutions, there is an exact solution to the inversion problem of extracting the orthogonal vectors from the coupled dimensions. Previously, this inversion problem has been solved using peak coordinates extracted from spectra. In contrast, the method described here uses spectra directly. This solution suggests a simple sampling scheme of collecting N orthogonal spectra, and N + 1 projections at specific projection angles, however, the theory developed can be extended generally to arbitrary projection angles. The circulant matrix methodology is demonstrated for simulated and real data. Further, an algorithm for separating overlapped signals in the detected dimension is presented. The algorithm involves the forward calculation of the coupled spectra from the orthogonal spectra, followed by back calculation of the orthogonal spectra from the coupled spectra, thus permitting rigorous cross-validation. This algorithm is shown to be robust in that erroneous solutions give rise to large artifacts
The development of a multi-dimensional gambling accessibility scale.
Hing, Nerilee; Haw, John
2009-12-01
The aim of the current study was to develop a scale of gambling accessibility that would have theoretical significance to exposure theory and also serve to highlight the accessibility risk factors for problem gambling. Scale items were generated from the Productivity Commission's (Australia's Gambling Industries: Report No. 10. AusInfo, Canberra, 1999) recommendations and tested on a group with high exposure to the gambling environment. In total, 533 gaming venue employees (aged 18-70 years; 67% women) completed a questionnaire that included six 13-item scales measuring accessibility across a range of gambling forms (gaming machines, keno, casino table games, lotteries, horse and dog racing, sports betting). Also included in the questionnaire was the Problem Gambling Severity Index (PGSI) along with measures of gambling frequency and expenditure. Principal components analysis indicated that a common three factor structure existed across all forms of gambling and these were labelled social accessibility, physical accessibility and cognitive accessibility. However, convergent validity was not demonstrated with inconsistent correlations between each subscale and measures of gambling behaviour. These results are discussed in light of exposure theory and the further development of a multi-dimensional measure of gambling accessibility.
Optimal Chunking of Large Multidimensional Arrays for Data Warehousing
Energy Technology Data Exchange (ETDEWEB)
Otoo, Ekow J; Otoo, Ekow J.; Rotem, Doron; Seshadri, Sridhar
2008-02-15
Very large multidimensional arrays are commonly used in data intensive scientific computations as well as on-line analytical processingapplications referred to as MOLAP. The storage organization of such arrays on disks is done by partitioning the large global array into fixed size sub-arrays called chunks or tiles that form the units of data transfer between disk and memory. Typical queries involve the retrieval of sub-arrays in a manner that access all chunks that overlap the query results. An important metric of the storage efficiency is the expected number of chunks retrieved over all such queries. The question that immediately arises is"what shapes of array chunks give the minimum expected number of chunks over a query workload?" The problem of optimal chunking was first introduced by Sarawagi and Stonebraker who gave an approximate solution. In this paper we develop exact mathematical models of the problem and provide exact solutions using steepest descent and geometric programming methods. Experimental results, using synthetic and real life workloads, show that our solutions are consistently within than 2.0percent of the true number of chunks retrieved for any number of dimensions. In contrast, the approximate solution of Sarawagi and Stonebraker can deviate considerably from the true result with increasing number of dimensions and also may lead to suboptimal chunk shapes.
Improving personality facet scores with multidimensional computer adaptive testing
DEFF Research Database (Denmark)
Makransky, Guido; Mortensen, Erik Lykke; Glas, Cees A W
2013-01-01
personality tests contain many highly correlated facets. This article investigates the possibility of increasing the precision of the NEO PI-R facet scores by scoring items with multidimensional item response theory and by efficiently administering and scoring items with multidimensional computer adaptive...
Multidimensional Computerized Adaptive Testing for Indonesia Junior High School Biology
Kuo, Bor-Chen; Daud, Muslem; Yang, Chih-Wei
2015-01-01
This paper describes a curriculum-based multidimensional computerized adaptive test that was developed for Indonesia junior high school Biology. In adherence to the Indonesian curriculum of different Biology dimensions, 300 items was constructed, and then tested to 2238 students. A multidimensional random coefficients multinomial logit model was…
The Tunneling Method for Global Optimization in Multidimensional Scaling.
Groenen, Patrick J. F.; Heiser, Willem J.
1996-01-01
A tunneling method for global minimization in multidimensional scaling is introduced and adjusted for multidimensional scaling with general Minkowski distances. The method alternates a local search step with a tunneling step in which a different configuration is sought with the same STRESS implementation. (SLD)
Multidimensional Physical Self-Concept of Athletes with Physical Disabilities
Shapiro, Deborah R.; Martin, Jeffrey J.
2010-01-01
The purposes of this investigation were first to predict reported PA (physical activity) behavior and self-esteem using a multidimensional physical self-concept model and second to describe perceptions of multidimensional physical self-concept (e.g., strength, endurance, sport competence) among athletes with physical disabilities. Athletes (N =…
Multidimensional filter banks and wavelets research developments and applications
Levy, Bernard
1997-01-01
Multidimensional Filter Banks and Wavelets: Reserach Developments and Applications brings together in one place important contributions and up-to-date research results in this important area. Multidimensional Filter Banks and Wavelets: Research Developments and Applications serves as an excellent reference, providing insight into some of the most important research issues in the field.
Multidimensional First-Order Dominance Comparisons of Population Wellbeing
DEFF Research Database (Denmark)
Siersbæk, Nikolaj; Østerdal, Lars Peter Raahave; Arndt, Thomas Channing
2017-01-01
This chapter conveys the concept of first-order dominance (FOD) with particular focus on applications to multidimensional population welfare comparisons. It gives an account of the fundamental equivalent definitions of FOD both in the one-dimensional and multidimensional setting, illustrated...
Supervised and Unsupervised Learning of Multidimensional Acoustic Categories
Goudbeek, Martijn; Swingley, Daniel; Smits, Roel
2009-01-01
Learning to recognize the contrasts of a language-specific phonemic repertoire can be viewed as forming categories in a multidimensional psychophysical space. Research on the learning of distributionally defined visual categories has shown that categories defined over 1 dimension are easy to learn and that learning multidimensional categories is…
Packing C60 in Boron Nitride Nanotubes
Mickelson, W.; Aloni, S.; Han, Wei-Qiang; Cumings, John; Zettl, A.
2003-04-01
We have created insulated C60 nanowire by packing C60 molecules into the interior of insulating boron nitride nanotubes (BNNTs). For small-diameter BNNTs, the wire consists of a linear chain of C60 molecules. With increasing BNNT inner diameter, unusual C60 stacking configurations are obtained (including helical, hollow core, and incommensurate) that are unknown for bulk or thin-film forms of C60. C60 in BNNTs thus presents a model system for studying the properties of dimensionally constrained ``silo'' crystal structures. For the linear-chain case, we have fused the C60 molecules to form a single-walled carbon nanotube inside the insulating BNNT.
Energy Technology Data Exchange (ETDEWEB)
Chung, B. D.; Bae, S. W.; Jeong, J. J.; Lee, S. M
2005-04-15
A new multi-dimensional component has been developed to allow for more flexible 3D capabilities in the system code, MARS. This component can be applied in the Cartesian and cylindrical coordinates. For the development of this model, the 3D convection and diffusion terms are implemented in the momentum and energy equation. And a simple Prandtl's mixing length model is applied for the turbulent viscosity. The developed multi-dimensional component was assessed against five conceptual problems with analytic solution. And some SETs are calculated and compared with experimental data. With this newly developed multi-dimensional flow module, the MARS code can realistic calculate the flow fields in pools such as those occurring in the core, steam generators and IRWST.
International Nuclear Information System (INIS)
Chung, B. D.; Bae, S. W.; Jeong, J. J.; Lee, S. M.
2005-04-01
A new multi-dimensional component has been developed to allow for more flexible 3D capabilities in the system code, MARS. This component can be applied in the Cartesian and cylindrical coordinates. For the development of this model, the 3D convection and diffusion terms are implemented in the momentum and energy equation. And a simple Prandtl's mixing length model is applied for the turbulent viscosity. The developed multi-dimensional component was assessed against five conceptual problems with analytic solution. And some SETs are calculated and compared with experimental data. With this newly developed multi-dimensional flow module, the MARS code can realistic calculate the flow fields in pools such as those occurring in the core, steam generators and IRWST
Argonne Code Center: benchmark problem book
International Nuclear Information System (INIS)
1977-06-01
This report is a supplement to the original report, published in 1968, as revised. The Benchmark Problem Book is intended to serve as a source book of solutions to mathematically well-defined problems for which either analytical or very accurate approximate solutions are known. This supplement contains problems in eight new areas: two-dimensional (R-z) reactor model; multidimensional (Hex-z) HTGR model; PWR thermal hydraulics--flow between two channels with different heat fluxes; multidimensional (x-y-z) LWR model; neutron transport in a cylindrical ''black'' rod; neutron transport in a BWR rod bundle; multidimensional (x-y-z) BWR model; and neutronic depletion benchmark problems. This supplement contains only the additional pages and those requiring modification
Multidimensional quantum entanglement with large-scale integrated optics.
Wang, Jianwei; Paesani, Stefano; Ding, Yunhong; Santagati, Raffaele; Skrzypczyk, Paul; Salavrakos, Alexia; Tura, Jordi; Augusiak, Remigiusz; Mančinska, Laura; Bacco, Davide; Bonneau, Damien; Silverstone, Joshua W; Gong, Qihuang; Acín, Antonio; Rottwitt, Karsten; Oxenløwe, Leif K; O'Brien, Jeremy L; Laing, Anthony; Thompson, Mark G
2018-04-20
The ability to control multidimensional quantum systems is central to the development of advanced quantum technologies. We demonstrate a multidimensional integrated quantum photonic platform able to generate, control, and analyze high-dimensional entanglement. A programmable bipartite entangled system is realized with dimensions up to 15 × 15 on a large-scale silicon photonics quantum circuit. The device integrates more than 550 photonic components on a single chip, including 16 identical photon-pair sources. We verify the high precision, generality, and controllability of our multidimensional technology, and further exploit these abilities to demonstrate previously unexplored quantum applications, such as quantum randomness expansion and self-testing on multidimensional states. Our work provides an experimental platform for the development of multidimensional quantum technologies. Copyright © 2018 The Authors, some rights reserved; exclusive licensee American Association for the Advancement of Science. No claim to original U.S. Government Works.
6D Visualization of Multidimensional Data by Means of Cognitive Technology
Vitkovskiy, V.; Gorohov, V.; Komarinskiy, S.
2010-12-01
On the basis of the cognitive graphics concept, we worked out the SW-system for visualization and analysis. It allows to train and to aggravate intuition of researcher, to raise his interest and motivation to the creative, scientific cognition, to realize process of dialogue with the very problems simultaneously. The Space Hedgehog system is the next step in the cognitive means of the multidimensional data analyze. The technique and technology cognitive 6D visualization of the multidimensional data is developed on the basis of the cognitive visualization research and technology development. The Space Hedgehog system allows direct dynamic visualization of 6D objects. It is developed with use of experience of the program Space Walker creation and its applications.
International Nuclear Information System (INIS)
Schaefer, A.
1979-02-01
A new code for efficient solution of the multidimensional stationary multi-group, diffusion equation, to be used within a HTGR-code model, is presented. The approximation and iteration methods are described. Spacial approximation is based on the QUABOX-coarse-mesh method, but iteration methods are different from QUABOX to give linear dependence of computation time on the number of energy groups. Results for various multidimensional multi-group problems, among them the THTR pebble bed reactor are analyzed. It is shown, that computational labor for a 3D-case is reduced by about a factor 30 in comparison with conventional finite-difference-methods. Thus 3D-full-core calculations appear to be feasible for large HTGR's. (orig.) [de
Optical Multidimensional Switching for Data Center Networks
DEFF Research Database (Denmark)
Kamchevska, Valerija
2017-01-01
. Software controlled switching using an on-chip integrated fiber switch is demonstrated and enabling of additional network functionalities such as multicast and optical grooming is experimentally confirmed. Altogether this work demonstrates the potential of optical switching technologies...... for the purpose of deploying optical switching within the network. First, the Hi-Ring data center architecture is proposed. It is based on optical multidimensional switching nodes that provide switching in hierarchically layered space, wavelength and time domain. The performance of the Hi-Ring architecture...... is evaluated experimentally and successful switching of both high capacity wavelength connections and time-shared subwavelengthconnections is demonstrated. Error-free performance is also achieved when transmitting 7 Tbit/s using multicore fiber, confirming the ability to scale the network. Moreover...
A complete set of multidimensional Bell inequalities
International Nuclear Information System (INIS)
Arnault, François
2012-01-01
We give a multidimensional generalization of the complete set of Bell-correlation inequalities given by Werner and Wolf (2001 Phys. Rev. A 64 032112) and by Zukowski and Brukner (2002 Phys. Rev. Lett. 88 210401), for the two-dimensional case. Our construction applies to the n-party, two-observable case, where each observable is d-valued. The d d n inequalities obtained involve homogeneous polynomials. They define the facets of a polytope in a complex vector space of dimension d n . We detail the inequalities obtained in the case d = 3 and, from them, we recover known inequalities. We finally explain how the violations of our inequalities by quantum mechanics can be computed and could be observed, when using unitary observables. (paper)
The simulation of multidimensional multiphase flows
International Nuclear Information System (INIS)
Lahey, Richard T.
2005-01-01
This paper presents an assessment of various models which can be used for the multidimensional simulation of multiphase flows, such as may occur in nuclear reactors. In particular, a model appropriate for the direct numerical simulation (DNS) of multiphase flows and a mechanistically based, three-dimensional, four-field, turbulent, two-fluid computational multiphase fluid dynamics (CMFD) model are discussed. A two-fluid bubbly flow model, which was derived using potential flow theory, can be extended to other flow regimes, but this will normally involve ensemble-averaging the results from direct numerical simulations (DNS) of various flow regimes to provide the detailed numerical data necessary for the development of flow-regime-specific interfacial and wall closure laws
Multidimensional splines for modeling FET nonlinearities
Energy Technology Data Exchange (ETDEWEB)
Barby, J A
1986-01-01
Circuit simulators like SPICE and timing simulators like MOTIS are used extensively for critical path verification of integrated circuits. MOSFET model evaluation dominates the run time of these simulators. Changes in technology results in costly updates, since modifications require reprogramming of the functions and their derivatives. The computational cost of MOSFET models can be reduced by using multidimensional polynomial splines. Since simulators based on the Newton Raphson algorithm require the function and first derivative, quadratic splines are sufficient for this purpose. The cost of updating the MOSFET model due to technology changes is greatly reduced since splines are derived from a set of points. Crucial for convergence speed of simulators is the fact that MOSFET characteristic equations are monotonic. This must be maintained by any simulation model. The splines the author designed do maintain monotonicity.
Multidimensional Scaling for Orthodontic Root Resorption
Directory of Open Access Journals (Sweden)
Cristina Teodora Preoteasa
2013-01-01
Full Text Available The paper investigates the risk factors for the severity of orthodontic root resorption. The multidimensional scaling (MDS visualization method is used to investigate the experimental data from patients who received orthodontic treatment at the Department of Orthodontics and Dentofacial Orthopedics, Faculty of Dentistry, “Carol Davila” University of Medicine and Pharmacy, during a period of 4 years. The clusters emerging in the MDS plots reveal features and properties not easily captured by classical statistical tools. The results support the adoption of MDS for tackling the dentistry information and overcoming noise embedded into the data. The method introduced in this paper is rapid, efficient, and very useful for treating the risk factors for the severity of orthodontic root resorption.
Multidimensional student skills with collaborative filtering
Bergner, Yoav; Rayyan, Saif; Seaton, Daniel; Pritchard, David E.
2013-01-01
Despite the fact that a physics course typically culminates in one final grade for the student, many instructors and researchers believe that there are multiple skills that students acquire to achieve mastery. Assessment validation and data analysis in general may thus benefit from extension to multidimensional ability. This paper introduces an approach for model determination and dimensionality analysis using collaborative filtering (CF), which is related to factor analysis and item response theory (IRT). Model selection is guided by machine learning perspectives, seeking to maximize the accuracy in predicting which students will answer which items correctly. We apply the CF to response data for the Mechanics Baseline Test and combine the results with prior analysis using unidimensional IRT.
Gender Ideologies in Europe: A Multidimensional Framework.
Grunow, Daniela; Begall, Katia; Buchler, Sandra
2018-02-01
The authors argue, in line with recent research, that operationalizing gender ideology as a unidimensional construct ranging from traditional to egalitarian is problematic and propose an alternative framework that takes the multidimensionality of gender ideologies into account. Using latent class analysis, they operationalize their gender ideology framework based on data from the 2008 European Values Study, of which eight European countries reflecting the spectrum of current work-family policies were selected. The authors examine the form in which gender ideologies cluster in the various countries. Five ideology profiles were identified: egalitarian, egalitarian essentialism, intensive parenting, moderate traditional, and traditional. The five ideology profiles were found in all countries, but with pronounced variation in size. Ideologies mixing gender essentialist and egalitarian views appear to have replaced traditional ideologies, even in countries offering some institutional support for gendered separate spheres.
Transport stochastic multi-dimensional media
International Nuclear Information System (INIS)
Haran, O.; Shvarts, D.
1996-01-01
Many physical phenomena evolve according to known deterministic rules, but in a stochastic media in which the composition changes in space and time. Examples to such phenomena are heat transfer in turbulent atmosphere with non uniform diffraction coefficients, neutron transfer in boiling coolant of a nuclear reactor and radiation transfer through concrete shields. The results of measurements conducted upon such a media are stochastic by nature, and depend on the specific realization of the media. In the last decade there has been a considerable efforts to describe linear particle transport in one dimensional stochastic media composed of several immiscible materials. However, transport in two or three dimensional stochastic media has been rarely addressed. The important effect in multi-dimensional transport that does not appear in one dimension is the ability to bypass obstacles. The current work is an attempt to quantify this effect. (authors)
Multidimensional scaling of musical time estimations.
Cocenas-Silva, Raquel; Bueno, José Lino Oliveira; Molin, Paul; Bigand, Emmanuel
2011-06-01
The aim of this study was to identify the psycho-musical factors that govern time evaluation in Western music from baroque, classic, romantic, and modern repertoires. The excerpts were previously found to represent variability in musical properties and to induce four main categories of emotions. 48 participants (musicians and nonmusicians) freely listened to 16 musical excerpts (lasting 20 sec. each) and grouped those that seemed to have the same duration. Then, participants associated each group of excerpts to one of a set of sine wave tones varying in duration from 16 to 24 sec. Multidimensional scaling analysis generated a two-dimensional solution for these time judgments. Musical excerpts with high arousal produced an overestimation of time, and affective valence had little influence on time perception. The duration was also overestimated when tempo and loudness were higher, and to a lesser extent, timbre density. In contrast, musical tension had little influence.
Transport stochastic multi-dimensional media
Energy Technology Data Exchange (ETDEWEB)
Haran, O; Shvarts, D [Israel Atomic Energy Commission, Beersheba (Israel). Nuclear Research Center-Negev; Thiberger, R [Ben-Gurion Univ. of the Negev, Beersheba (Israel)
1996-12-01
Many physical phenomena evolve according to known deterministic rules, but in a stochastic media in which the composition changes in space and time. Examples to such phenomena are heat transfer in turbulent atmosphere with non uniform diffraction coefficients, neutron transfer in boiling coolant of a nuclear reactor and radiation transfer through concrete shields. The results of measurements conducted upon such a media are stochastic by nature, and depend on the specific realization of the media. In the last decade there has been a considerable efforts to describe linear particle transport in one dimensional stochastic media composed of several immiscible materials. However, transport in two or three dimensional stochastic media has been rarely addressed. The important effect in multi-dimensional transport that does not appear in one dimension is the ability to bypass obstacles. The current work is an attempt to quantify this effect. (authors).
Multidimensional fractional Schrödinger equation
Rodrigues, M. M.; Vieira, N.
2012-11-01
This work is intended to investigate the multi-dimensional space-time fractional Schrödinger equation of the form (CDt0+αu)(t,x) = iħ/2m(C∇βu)(t,x), with ħ the Planck's constant divided by 2π, m is the mass and u(t,x) is a wave function of the particle. Here (CDt0+α,C∇β are operators of the Caputo fractional derivatives, where α ∈]0,1] and β ∈]1,2]. The wave function is obtained using Laplace and Fourier transforms methods and a symbolic operational form of solutions in terms of the Mittag-Leffler functions is exhibited. It is presented an expression for the wave function and for the quantum mechanical probability density. Using Banach fixed point theorem, the existence and uniqueness of solutions is studied for this kind of fractional differential equations.
Multidimensional evaluation on FR cycle systems
International Nuclear Information System (INIS)
Nakai, Ryodai; Fujii, Sumio; Takakuma, Katsuyuki; Katoh, Atsushi; Ono, Kiyoshi; Ohtaki, Akira; Shiotani, Hiroki
2004-01-01
This report explains some results of the multidimensional evaluation on various fast reactor cycle system concepts from an interim report of the 2nd phase of ''Feasibility Study on Commercialized FR Cycle System''. This method is designed to give more objective and more quantitative evaluations to clarify commercialized system candidate concepts. Here we brief current evaluation method from the five viewpoints of safety, economy, environment, resource and non-proliferation, with some trial evaluation results for some cycles consist of promising technologies in reactor, core and fuel, reprocessing and fuel manufacture. Moreover, we describe FR cycle deployment scenarios which describe advantages and disadvantages of the cycles from the viewpoints of uranium resource and radioactive waste based on long-term nuclear material mass flow analyses and advantages of the deployment of FR cycle itself from the viewpoints of the comparison with alternative power supplies as well as cost and benefit. (author)
Gender Ideologies in Europe: A Multidimensional Framework
Begall, Katia; Buchler, Sandra
2018-01-01
The authors argue, in line with recent research, that operationalizing gender ideology as a unidimensional construct ranging from traditional to egalitarian is problematic and propose an alternative framework that takes the multidimensionality of gender ideologies into account. Using latent class analysis, they operationalize their gender ideology framework based on data from the 2008 European Values Study, of which eight European countries reflecting the spectrum of current work–family policies were selected. The authors examine the form in which gender ideologies cluster in the various countries. Five ideology profiles were identified: egalitarian, egalitarian essentialism, intensive parenting, moderate traditional, and traditional. The five ideology profiles were found in all countries, but with pronounced variation in size. Ideologies mixing gender essentialist and egalitarian views appear to have replaced traditional ideologies, even in countries offering some institutional support for gendered separate spheres. PMID:29491532
Contaminant bacteria in traditional-packed honey
Directory of Open Access Journals (Sweden)
Hening Tjaturina Pramesti
2007-03-01
Full Text Available Honey may be contaminated by microorganisms during its harvesting, processing, and packaging. Honey selected for clinical purposes must safe, sterile, and contain antimicrobial activity, so it must be evaluated using laboratory testing. The aim of this descriptive laboratory study was to isolate and identify the bacterial contaminant in the traditional-packed honey dealing with the use of honey for medical purposes. the colony forming units of honey sample cultured on blood agar were counted using Stuart bacterial colony counter. The suspected bacterial colonies were isolated and identified based on cultural morphology characteristics. The isolates of suspected bacterial colonies were stained according to Gram and Klein method and then were examined by the biochemical reaction. The results showed that there were two contaminant bacteria. Gram-positive cocci which were presumptively identified as coagulase-negative Staphylococci and gram-positive rods which were presumptively identified as Bacillus subtilis. In conclusion, the contaminant bacteria were regarded as low pathogen bacteria. The subtilin enzyme of B subtilis may cause an allergic reaction and coagulase-negative Staphylococci, Staphylococcus epidermidis is also an opportunist pathogen. Inevitably, for medical purposes, traditional-packed honey must be well filtered, water content above 18%, and standardized sterilization without loss of an antibacterial activity or change in properties.
International Nuclear Information System (INIS)
Bareiss, E.H.
1976-05-01
The objectives of the work are to develop mathematically and computationally founded for the design of highly efficient and reliable multidimensional neutron transport codes to solve a variety of neutron migration and radiation problems, and to analyze existing and new methods for performance. As new analytical insights are gained, new numerical methods are developed and tested. Significant results obtained include implementation of the integer-preserving Gaussian elimination method (two-step method) in a CDC 6400 computer code, modes analysis for one-dimensional transport solutions, and a new method for solving the 1-T transport equation. Some of the work dealt with the interface and corner problem in diffusion theory
Mechanised packing for longwall coal faces. Monolithic packing and powered supports for the packhole
Energy Technology Data Exchange (ETDEWEB)
Carr, F; Kitching, F
1978-11-01
If full advantage is to be taken of the great advances that have taken place in power loading and powered support at the coalface, other operations in that vicinity must be similarly mechanised and automated. The gateside packing is one of the most important of these ancillary operations on the longwall face, and in previous articles F. Carr and F. Kitching, National Coal Board Headquarters, Coalface Operations Mining Engineers have given a very comprehensive resume of the present situation. Subjects covered include the requirements of mechanised packing, the parameters involved, the various working arrangements, the different systems of gate-ends, the types of equipment that are being used, their characteristics, the spread of their application, and the results obtained from them. In this article the authors conclude their survey by dealing with dirt/cement and anhydrite packing, by taking a hard look at powered supports for the packhole, and by expressing their views on the way mechanised packing may be expected to develop in the future.
The necessity-concerns framework: a multidimensional theory benefits from multidimensional analysis.
Phillips, L Alison; Diefenbach, Michael A; Kronish, Ian M; Negron, Rennie M; Horowitz, Carol R
2014-08-01
Patients' medication-related concerns and necessity-beliefs predict adherence. Evaluation of the potentially complex interplay of these two dimensions has been limited because of methods that reduce them to a single dimension (difference scores). We use polynomial regression to assess the multidimensional effect of stroke-event survivors' medication-related concerns and necessity beliefs on their adherence to stroke-prevention medication. Survivors (n = 600) rated their concerns, necessity beliefs, and adherence to medication. Confirmatory and exploratory polynomial regression determined the best-fitting multidimensional model. As posited by the necessity-concerns framework (NCF), the greatest and lowest adherence was reported by those necessity weak concerns and strong concerns/weak Necessity-Beliefs, respectively. However, as could not be assessed using a difference-score model, patients with ambivalent beliefs were less adherent than those exhibiting indifference. Polynomial regression allows for assessment of the multidimensional nature of the NCF. Clinicians/Researchers should be aware that concerns and necessity dimensions are not polar opposites.
The Necessity-Concerns-Framework: A Multidimensional Theory Benefits from Multidimensional Analysis
Phillips, L. Alison; Diefenbach, Michael; Kronish, Ian M.; Negron, Rennie M.; Horowitz, Carol R.
2014-01-01
Background Patients’ medication-related concerns and necessity-beliefs predict adherence. Evaluation of the potentially complex interplay of these two dimensions has been limited because of methods that reduce them to a single dimension (difference scores). Purpose We use polynomial regression to assess the multidimensional effect of stroke-event survivors’ medication-related concerns and necessity-beliefs on their adherence to stroke-prevention medication. Methods Survivors (n=600) rated their concerns, necessity-beliefs, and adherence to medication. Confirmatory and exploratory polynomial regression determined the best-fitting multidimensional model. Results As posited by the Necessity-Concerns Framework (NCF), the greatest and lowest adherence was reported by those with strong necessity-beliefs/weak concerns and strong concerns/weak necessity-beliefs, respectively. However, as could not be assessed using a difference-score model, patients with ambivalent beliefs were less adherent than those exhibiting indifference. Conclusions Polynomial regression allows for assessment of the multidimensional nature of the NCF. Clinicians/Researchers should be aware that concerns and necessity dimensions are not polar opposites. PMID:24500078
Content-aware photo collage using circle packing.
Yu, Zongqiao; Lu, Lin; Guo, Yanwen; Fan, Rongfei; Liu, Mingming; Wang, Wenping
2014-02-01
In this paper, we present a novel approach for automatically creating the photo collage that assembles the interest regions of a given group of images naturally. Previous methods on photo collage are generally built upon a well-defined optimization framework, which computes all the geometric parameters and layer indices for input photos on the given canvas by optimizing a unified objective function. The complex nonlinear form of optimization function limits their scalability and efficiency. From the geometric point of view, we recast the generation of collage as a region partition problem such that each image is displayed in its corresponding region partitioned from the canvas. The core of this is an efficient power-diagram-based circle packing algorithm that arranges a series of circles assigned to input photos compactly in the given canvas. To favor important photos, the circles are associated with image importances determined by an image ranking process. A heuristic search process is developed to ensure that salient information of each photo is displayed in the polygonal area resulting from circle packing. With our new formulation, each factor influencing the state of a photo is optimized in an independent stage, and computation of the optimal states for neighboring photos are completely decoupled. This improves the scalability of collage results and ensures their diversity. We also devise a saliency-based image fusion scheme to generate seamless compositive collage. Our approach can generate the collages on nonrectangular canvases and supports interactive collage that allows the user to refine collage results according to his/her personal preferences. We conduct extensive experiments and show the superiority of our algorithm by comparing against previous methods.
Coil winding pack FE-analysis for a HELIAS reactor
International Nuclear Information System (INIS)
Schauer, F.; Egorov, K.; Bykov, V.
2011-01-01
At the Max-Planck-Institut fuer Plasmaphysik (IPP) a reference design is being created of an upgraded five-periodic HELIAS type stellarator reactor which evolves from Wendelstein 7-X (W7-X) by scaling of the coil centre line geometries by a factor of four. This reactor type was extensively investigated at IPP with regard to physical characteristics and to some extent also to engineering issues. The upgrade concerns an increase of the induction at the plasma axis and correspondingly at the superconductor. The aim is to develop the reactor concept to a stage and such detail that major engineering problems are unveiled, and relevant comparisons with other concepts, including tokamaks, can be drawn in view of upcoming decisions concerning a DEMO reactor. Even though progress in plasma physics, and in particular future results of W7-X and other machines - particularly of ITER - will probably lead to somewhat different coil shapes, no principal changes of the reference design are expected. In this paper the option of a roll-formed square coil cable jacket is investigated. Detailed structural FE analysis of the coil winding pack demonstrates the feasibility of such a conductor which appears to be the most economical option. It also allows sufficient space for a cable current density very similar to that of the ITER TF coil with a similar overall winding pack cross section of ∼0.5 m 2 . Already existing Nb 3 Sn conductors could thus be safely applied in such a HELIAS reactor. Obvious progress of superconductor technology, particularly concerning Nb 3 Al, will be beneficial concerning savings of conductor material, ease of manufacture, higher operation temperature, etc.
Simulation of abuse tolerance of lithium-ion battery packs
Energy Technology Data Exchange (ETDEWEB)
Spotnitz, Robert M.; Weaver, James; Yeduvaka, Gowri [Battery Design LLC, 2277 DeLucchi Drive, Pleasanton, CA 94588 (United States); Doughty, D.H.; Roth, E.P. [Lithium Battery Department, Sandia National Laboratories, Albuquerque, NM 87185 (United States)
2007-01-01
A simple approach for using accelerating rate calorimetry data to simulate the thermal abuse resistance of battery packs is described. The thermal abuse tolerance of battery packs is estimated based on the exothermic behavior of a single cell and an energy balance than accounts for radiative, conductive, and convective heat transfer modes of the pack. For the specific example of a notebook computer pack containing eight 18650-size cells, the effects of cell position, heat of reaction, and heat-transfer coefficient are explored. Thermal runaway of the pack is more likely to be induced by thermal runaway of a single cell when that cell is in good contact with other cells and is close to the pack wall. (author)
Multilayer DNA Origami Packed on Hexagonal and Hybrid Lattices
Ke, Yonggang; Voigt, Niels V.; Gothelf, Kurt V.; Shih, William M.
2012-01-01
“Scaffolded DNA origami” has been proven to be a powerful and efficient approach to construct two-dimensional or three-dimensional objects with great complexity. Multilayer DNA origami has been demonstrated with helices packing along either honeycomb-lattice geometry or square-lattice geometry. Here we report successful folding of multilayer DNA origami with helices arranged on a close-packed hexagonal lattice. This arrangement yields a higher density of helical packing and therefore higher r...
Ganesan, Nandhini; Basu, Suman; Hariharan, Krishnan S.; Kolake, Subramanya Mayya; Song, Taewon; Yeo, Taejung; Sohn, Dong Kee; Doo, Seokgwang
2016-08-01
Lithium-Ion batteries used for electric vehicle applications are subject to large currents and various operation conditions, making battery pack design and life extension a challenging problem. With increase in complexity, modeling and simulation can lead to insights that ensure optimal performance and life extension. In this manuscript, an electrochemical-thermal (ECT) coupled model for a 6 series × 5 parallel pack is developed for Li ion cells with NCA/C electrodes and validated against experimental data. Contribution of the cathode to overall degradation at various operating conditions is assessed. Pack asymmetry is analyzed from a design and an operational perspective. Design based asymmetry leads to a new approach of obtaining the individual cell responses of the pack from an average ECT output. Operational asymmetry is demonstrated in terms of effects of thermal gradients on cycle life, and an efficient model predictive control technique is developed. Concept of reconfigurable battery pack is studied using detailed simulations that can be used for effective monitoring and extension of battery pack life.
Max–min Bin Packing Algorithm and its application in nano-particles filling
International Nuclear Information System (INIS)
Zhu, Dingju
2016-01-01
With regard to existing bin packing algorithms, higher packing efficiency often leads to lower packing speed while higher packing speed leads to lower packing efficiency. Packing speed and packing efficiency of existing bin packing algorithms including NFD, NF, FF, FFD, BF and BFD correlates negatively with each other, thus resulting in the failure of existing bin packing algorithms to satisfy the demand of nano-particles filling for both high speed and high efficiency. The paper provides a new bin packing algorithm, Max–min Bin Packing Algorithm (MM), which realizes both high packing speed and high packing efficiency. MM has the same packing speed as NFD (whose packing speed ranks no. 1 among existing bin packing algorithms); in case that the size repetition rate of objects to be packed is over 5, MM can realize almost the same packing efficiency as BFD (whose packing efficiency ranks No. 1 among existing bin packing algorithms), and in case that the size repetition rate of objects to be packed is over 500, MM can achieve exactly the same packing efficiency as BFD. With respect to application of nano-particles filling, the size repetition rate of nano particles to be packed is usually in thousands or ten thousands, far higher than 5 or 500. Consequently, in application of nano-particles filling, the packing efficiency of MM is exactly equal to that of BFD. Thus the irreconcilable conflict between packing speed and packing efficiency is successfully removed by MM, which leads to MM having better packing effect than any existing bin packing algorithm. In practice, there are few cases when the size repetition of objects to be packed is lower than 5. Therefore the MM is not necessarily limited to nano-particles filling, and can also be widely used in other applications besides nano-particles filling. Especially, MM has significant value in application of nano-particles filling such as nano printing and nano tooth filling.
Meromorphic Vector Fields and Circle Packings
DEFF Research Database (Denmark)
Dias, Kealey
The objective of the Ph.D. project is to initiate a classification of bifurcations of meromorphic vector fields and to clarify their relation to circle packings. Technological applications are to image analysis and to effective grid generation using discrete conformal mappings. The two branches...... of dynamical systems, continuous and discrete, correspond to the study of differential equations (vector fields) and iteration of mappings respectively. In holomorphic dynamics, the systems studied are restricted to those described by holomorphic (complex analytic) functions or meromorphic (allowing poles...... as singularities) functions. There already exists a well-developed theory for iterative holomorphic dynamical systems, and successful relations found between iteration theory and flows of vector fields have been one of the main motivations for the recent interest in holomorphic vector fields. Restricting...
Hyperstaticity and loops in frictional granular packings
Tordesillas, Antoinette; Lam, Edward; Metzger, Philip T.
2009-06-01
The hyperstatic nature of granular packings of perfectly rigid disks is analyzed algebraically and through numerical simulation. The elementary loops of grains emerge as a fundamental element in addressing hyperstaticity. Loops consisting of an odd number of grains behave differently than those with an even number. For odd loops, the latent stresses are exterior and are characterized by the sum of frictional forces around each loop. For even loops, the latent stresses are interior and are characterized by the alternating sum of frictional forces around each loop. The statistics of these two types of loop sums are found to be Gibbsian with a "temperature" that is linear with the friction coefficient μ when μ<1.
New Packing Structure of Concentration Solar Receiver
International Nuclear Information System (INIS)
Tsai, Shang-Yu; Lee, Yueh-Mu; Shih, Zun-Hao; Hong, Hwen-Fen; Shin, Hwa-Yuh; Kuo, Cherng-Tsong
2010-01-01
This paper presents a solution to the temperature issue in High Concentration Photovoltaic (HCPV) module device by using different thermal conductive material and packing structure. In general, the open-circuited voltage of a device reduces with the increase of temperature and therefore degrades its efficiency. The thermal conductive material we use in this paper, silicon, has a high thermal conductive coefficient (149 W/m·K) and steady semiconductor properties which are suitable for the application of solar receiver in HCPV module. Solar cell was soldered on a metal-plated Si substrate with a thicker SiO 2 film which acts as an insulating layer. Then it was mounted on an Al-based plate to obtain a better heat dissipating result.
Slow creep in soft granular packings.
Srivastava, Ishan; Fisher, Timothy S
2017-05-14
Transient creep mechanisms in soft granular packings are studied numerically using a constant pressure and constant stress simulation method. Rapid compression followed by slow dilation is predicted on the basis of a logarithmic creep phenomenon. Characteristic scales of creep strain and time exhibit a power-law dependence on jamming pressure, and they diverge at the jamming point. Microscopic analysis indicates the existence of a correlation between rheology and nonaffine fluctuations. Localized regions of large strain appear during creep and grow in magnitude and size at short times. At long times, the spatial structure of highly correlated local deformation becomes time-invariant. Finally, a microscale connection between local rheology and local fluctuations is demonstrated in the form of a linear scaling between granular fluidity and nonaffine velocity.
A study of multidimensional modeling approaches for data warehouse
Yusof, Sharmila Mat; Sidi, Fatimah; Ibrahim, Hamidah; Affendey, Lilly Suriani
2016-08-01
Data warehouse system is used to support the process of organizational decision making. Hence, the system must extract and integrate information from heterogeneous data sources in order to uncover relevant knowledge suitable for decision making process. However, the development of data warehouse is a difficult and complex process especially in its conceptual design (multidimensional modeling). Thus, there have been various approaches proposed to overcome the difficulty. This study surveys and compares the approaches of multidimensional modeling and highlights the issues, trend and solution proposed to date. The contribution is on the state of the art of the multidimensional modeling design.
A Conceptual Model for Multidimensional Analysis of Documents
Ravat, Franck; Teste, Olivier; Tournier, Ronan; Zurlfluh, Gilles
Data warehousing and OLAP are mainly used for the analysis of transactional data. Nowadays, with the evolution of Internet, and the development of semi-structured data exchange format (such as XML), it is possible to consider entire fragments of data such as documents as analysis sources. As a consequence, an adapted multidimensional analysis framework needs to be provided. In this paper, we introduce an OLAP multidimensional conceptual model without facts. This model is based on the unique concept of dimensions and is adapted for multidimensional document analysis. We also provide a set of manipulation operations.
Software complex for developing dynamically packed program system for experiment automation
International Nuclear Information System (INIS)
Baluka, G.; Salamatin, I.M.
1985-01-01
Software complex for developing dynamically packed program system for experiment automation is considered. The complex includes general-purpose programming systems represented as the RT-11 standard operating system and specially developed problem-oriented moduli providing execution of certain jobs. The described complex is realized in the PASKAL' and MAKRO-2 languages and it is rather flexible to variations of the technique of the experiment
Local fields for asymptotic matching in multidimensional mode conversion
International Nuclear Information System (INIS)
Tracy, E. R.; Kaufman, A. N.; Jaun, A.
2007-01-01
The problem of resonant mode conversion in multiple spatial dimensions is considered. Using phase space methods, a complete theory is developed for constructing matched asymptotic expansions that fit incoming and outgoing WKB solutions. These results provide, for the first time, a complete and practical method for including multidimensional conversion in ray tracing algorithms. The paper provides a self-contained description of the following topics: (1) how to use eikonal (also known as ray tracing or WKB) methods to solve vector wave equations and how to detect conversion regions while following rays; (2) once conversion is detected, how to fit to a generic saddle structure in ray phase space associated with the most common type of conversion; (3) given the saddle structure, how to carry out a local projection of the full vector wave equation onto a local two-component normal form that governs the two resonantly interacting waves. This determines both the uncoupled dispersion functions and the coupling constant, which in turn determine the uncoupled WKB solutions; (4) given the normal form of the local two-component wave equation, how to find the particular solution that matches the amplitude, phase, and polarization of the incoming ray, to the amplitude, phase, and polarization of the two outgoing rays: the transmitted and converted rays
Multidimensional electron-photon transport with standard discrete ordinates codes
International Nuclear Information System (INIS)
Drumm, C.R.
1997-01-01
A method is described for generating electron cross sections that are comparable with standard discrete ordinates codes without modification. There are many advantages of using an established discrete ordinates solver, e.g. immediately available adjoint capability. Coupled electron-photon transport capability is needed for many applications, including the modeling of the response of electronics components to space and man-made radiation environments. The cross sections have been successfully used in the DORT, TWODANT and TORT discrete ordinates codes. The cross sections are shown to provide accurate and efficient solutions to certain multidimensional electron-photon transport problems. The key to the method is a simultaneous solution of the continuous-slowing-down (CSD) portion and elastic-scattering portion of the scattering source by the Goudsmit-Saunderson theory. The resulting multigroup-Legendre cross sections are much smaller than the true scattering cross sections that they represent. Under certain conditions, the cross sections are guaranteed positive and converge with a low-order Legendre expansion
Multidimensional electron-photon transport with standard discrete ordinates codes
International Nuclear Information System (INIS)
Drumm, C.R.
1997-01-01
A method is described for generating electron cross sections that are compatible with standard discrete ordinates codes without modification. There are many advantages to using an established discrete ordinates solver, e.g., immediately available adjoint capability. Coupled electron-photon transport capability is needed for many applications, including the modeling of the response of electronics components to space and synthetic radiation environments. The cross sections have been successfully used in the DORT, TWODANT, and TORT discrete ordinates codes. The cross sections are shown to provide accurate and efficient solutions to certain multidimensional electron-photon transport problems. The key to the method is a simultaneous solution of the continuous-slowing-down and elastic-scattering portions of the scattering source by the Goudsmit-Saunderson theory. The resulting multigroup-Legendre cross sections are much smaller than the true scattering cross sections that they represent. Under certain conditions, the cross sections are guaranteed positive and converge with a low-order Legendre expansion
Standardized Definitions for Code Verification Test Problems
Energy Technology Data Exchange (ETDEWEB)
Doebling, Scott William [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)
2017-09-14
This document contains standardized definitions for several commonly used code verification test problems. These definitions are intended to contain sufficient information to set up the test problem in a computational physics code. These definitions are intended to be used in conjunction with exact solutions to these problems generated using Exact- Pack, www.github.com/lanl/exactpack.
International Nuclear Information System (INIS)
Lee, Kyung Haeng; Yun, Hyejeong; Lee, Ju Woon; Ahn, Dong Uk; Lee, Eun Joo; Jo, Cheorun
2012-01-01
Irradiation is the most efficient non-thermal technology for improving hygienic quality and extending the shelf-life of food products. One of the adverse effects of food irradiation, however, is off-flavor production, which significantly affects the sensory preferences for certain foods. In this study, garlic (5%, w/w) and red wine (1:1, w/w) were added to ground beef to increase the radiation sensitivity of pathogens and improve meat odor/flavor. Samples were irradiated at 0 or 5 kGy in the presence of charcoal pack. SPME-GC–MS analysis was performed to measure the changes in the volatile compounds and sensory characteristics of the samples. The amount of total volatile compounds produced from ground beef was greater when the sample was irradiated. When garlic and red wine were added to the ground beef, the amount of volatile compounds significantly increased, and the amount of volatile compounds increased even further after irradiation. However, when the samples were irradiated with charcoal pack, the amount of volatile compounds decreased significantly. Sensory evaluation indicated that charcoal pack significantly increased the odor preferences for both irradiated and non-irradiated ground beef added with garlic. These results indicated that addition of charcoal pack to ground beef could reduce off-odor problems induced by irradiation, and this effect was consistent even when certain additives such as garlic and red wine were added. - Highlights: ► Garlic and red wine were added to ground beef and irradiated at 5 kGy in the presence of charcoal pack. ► When the samples were irradiated with charcoal pack, the amount of volatile compounds decreased significantly and it affected sensory score. ► Thus, addition of charcoal pack to ground beef could reduce off-odor problems induced by irradiation. ► This effect was consistent when additives, such as garlic and red wine, were added into ground beef.
New series of paper pack vending machines; Paper pack jido hanbaiki no shin series
Energy Technology Data Exchange (ETDEWEB)
Ohashi, M. [Fuji Denki Reiki Co. Ltd., Tokyo (Japan); Umino, S. [Fuji Electric Co. Ltd., Tokyo (Japan)
1996-07-10
This paper presents series of paper pack vending machines. These machines may be broadly classified into those of cold drinks and of hot and cold drinks depending on the storage temperature of products. The former is the machine for cooling dairy products at 10{degree}C with a combined stacking by direct-stacked racks and chain-multiracks. The latter is provided with divided storing chambers with each chamber selectively cooled or heated. Products in the hot chamber are canned coffee and the like set at 55{degree}C. The temperature control is performed by a microcomputer. The chain-multiracks are provided with advantages such as capability of handling various kinds of container shapes, storing drinks and foods vertically, replacing products by the change of a shelf attachment with one operation, and storing one liter packs by setting pair columns. The direct-stacked racks are provided with advantages such as versatility of handling various kinds of containers and miniaturization of the mechanism other than the storage part. The installation space was reduced by devising the opening and closing of the door. The control part is capable of setting temperatures differently for cans and paper packs. 7 figs., 1 tab.
A DYNAMIC INDEXING SCHEME FOR MULTIDIMENSIONAL DATA
Directory of Open Access Journals (Sweden)
Manuk G. Manukyan
2018-03-01
Full Text Available We present a new dynamic index structure for multidimensional data. The considered index structure is based on an extended grid file concept. Strengths and weaknesses of the grid files were analyzed. Based on that analysis we proposed to strengthen the concept of grid files by considering their stripes as linear hash tables, introducing the concept of chunk and representing the grid file structure as a graph. As a result we significantly reduced the amount of disk operations. Efficient algorithms for storage and access of index directory are proposed, in order to minimize memory usage and lookup operations complexities. Estimations of complexities for these algorithms are presented. A comparison of our approach to support effective grid file structure with other known approaches is presented. This comparison shows effectiveness of suggested metadata storage environment. An estimation of directory size is presented. A prototype to support of our grid file concept has been created and experimentally compared with MongoDB (a renowned NoSQL database. Comparison results show effectiveness of our approach in the cases of given point lookup, lookup by wide ranges and closest objects lookup when considering more than one dimension, and also better memory usage.
Proposed empirical gas geothermometer using multidimensional approach
Energy Technology Data Exchange (ETDEWEB)
Supranto; Sudjatmiko; Toha, Budianto; Wintolo, Djoko; Alhamid, Idrus
1996-01-24
Several formulas of surface gas geothermometer have been developed to utilize in geothermal exploration, i.e. by D'Amore and Panichi (1980) and by Darling and Talbot (1992). This paper presents an empirical gas geothermometer formula using multidimensional approach. The formula was derived from 37 selected chemical data of the 5 production wells from the Awibengkok Geothermal Volcanic Field in West Java. Seven components, i.e., gas volume percentage, CO_{2}, H_{2}S, CH_{4}, H_{2}, N_{2}, and NH_{3}, from these data are utilize to developed three model equations which represent relationship between temperature and gas compositions. These formulas are then tested by several fumarolic chemical data from Sibual-buali Area (North Sumatera) and from Ringgit Area (South Sumatera). Preliminary result indicated that gas volume percentage, H_{2}S and CO_{2} concentrations have a significant role in term of gas geothermometer. Further verification is currently in progress.
Multi-dimensional cosmology and GUP
Energy Technology Data Exchange (ETDEWEB)
Zeynali, K.; Motavalli, H. [Department of Theoretical Physics and Astrophysics, University of Tabriz, 51666-16471, Tabriz (Iran, Islamic Republic of); Darabi, F., E-mail: k.zeinali@arums.ac.ir, E-mail: f.darabi@azaruniv.edu, E-mail: motavalli@tabrizu.ac.ir [Department of Physics, Azarbaijan Shahid Madani University, 53714-161, Tabriz (Iran, Islamic Republic of)
2012-12-01
We consider a multidimensional cosmological model with FRW type metric having 4-dimensional space-time and d-dimensional Ricci-flat internal space sectors with a higher dimensional cosmological constant. We study the classical cosmology in commutative and GUP cases and obtain the corresponding exact solutions for negative and positive cosmological constants. It is shown that for negative cosmological constant, the commutative and GUP cases result in finite size universes with smaller size and longer ages, and larger size and shorter age, respectively. For positive cosmological constant, the commutative and GUP cases result in infinite size universes having late time accelerating behavior in good agreement with current observations. The accelerating phase starts in the GUP case sooner than the commutative case. In both commutative and GUP cases, and for both negative and positive cosmological constants, the internal space is stabilized to the sub-Planck size, at least within the present age of the universe. Then, we study the quantum cosmology by deriving the Wheeler-DeWitt equation, and obtain the exact solutions in the commutative case and the perturbative solutions in GUP case, to first order in the GUP small parameter, for both negative and positive cosmological constants. It is shown that good correspondence exists between the classical and quantum solutions.
Multi-dimensional cosmology and GUP
International Nuclear Information System (INIS)
Zeynali, K.; Motavalli, H.; Darabi, F.
2012-01-01
We consider a multidimensional cosmological model with FRW type metric having 4-dimensional space-time and d-dimensional Ricci-flat internal space sectors with a higher dimensional cosmological constant. We study the classical cosmology in commutative and GUP cases and obtain the corresponding exact solutions for negative and positive cosmological constants. It is shown that for negative cosmological constant, the commutative and GUP cases result in finite size universes with smaller size and longer ages, and larger size and shorter age, respectively. For positive cosmological constant, the commutative and GUP cases result in infinite size universes having late time accelerating behavior in good agreement with current observations. The accelerating phase starts in the GUP case sooner than the commutative case. In both commutative and GUP cases, and for both negative and positive cosmological constants, the internal space is stabilized to the sub-Planck size, at least within the present age of the universe. Then, we study the quantum cosmology by deriving the Wheeler-DeWitt equation, and obtain the exact solutions in the commutative case and the perturbative solutions in GUP case, to first order in the GUP small parameter, for both negative and positive cosmological constants. It is shown that good correspondence exists between the classical and quantum solutions
Convergence almost everywhere of multidimensional vectors
International Nuclear Information System (INIS)
El Berdan, Kassem; Zeineddine, Hassan
2000-01-01
Let X be a reflexive Banach space, Ω a measure space, T 1 ,...,T d be linear not commuting operators on L 1 (Ω,X)=L 1 (X) which are strictly contracting in L 1 (X) (i.e. there exist αjbelong to ]0,1[ such that ||T j f||≤αj||f|| for all j=1....,d and f belong to L 1 (X), and contracting in L ∞ (X). We prove a maximal equality for the averages: A n (T 1 ,...,T d )f= n d /1 i1=0 Σ n-1 ... id=0 Σ n-1 T 1 i1 ...T d id f and the convergence almost everywhere of it for all f in L 1 (X). This result generalizes Chacon's theorem (Chacon 19620 to the multidimensional case for this operators class. Finally, we give two operators which are strictly contracting in L 1 (X) and contracting in L ∞ (X) such that the convergence of the averages is not trivial. (author)
Multidimensional Scaling Visualization Using Parametric Similarity Indices
Directory of Open Access Journals (Sweden)
J. A. Tenreiro Machado
2015-03-01
Full Text Available In this paper, we apply multidimensional scaling (MDS and parametric similarity indices (PSI in the analysis of complex systems (CS. Each CS is viewed as a dynamical system, exhibiting an output time-series to be interpreted as a manifestation of its behavior. We start by adopting a sliding window to sample the original data into several consecutive time periods. Second, we define a given PSI for tracking pieces of data. We then compare the windows for different values of the parameter, and we generate the corresponding MDS maps of ‘points’. Third, we use Procrustes analysis to linearly transform the MDS charts for maximum superposition and to build a globalMDS map of “shapes”. This final plot captures the time evolution of the phenomena and is sensitive to the PSI adopted. The generalized correlation, theMinkowski distance and four entropy-based indices are tested. The proposed approach is applied to the Dow Jones Industrial Average stock market index and the Europe Brent Spot Price FOB time-series.
Energy Poverty in Europe: A Multidimensional Approach
Directory of Open Access Journals (Sweden)
Carlo Andrea Bollino
2017-12-01
Full Text Available With the European Commission’s “Third Energy Package”, the challenges posed by energy poverty have been recently acknowledged by European legislation. The paper develops a synthetic indicator of energy poverty for the purpose of assessing households’ well-being across different domains of inequality in access to energy services and to a healthy domestic environment. These dimensions are broadly defined in terms of energy affordability and thermal efficiency, two of the main manifestations of energy poverty. The analysis focuses on Europe and expands on existing economic literature by employing a fuzzy analysis for the definition of a multidimensional energy poverty index, which is then used to investigate the role of individual and household characteristics in shaping energy poverty. We find that during the European crisis energy poverty has been more stable than monetary poverty, and that thermal efficiency plays a crucial role in shaping individual and countries’ average degrees of energy poverty. JEL codes: I32; Q41; D10; D63
Control of multidimensional systems on complex network
Bagnoli, Franco; Battistelli, Giorgio; Chisci, Luigi; Fanelli, Duccio
2017-01-01
Multidimensional systems coupled via complex networks are widespread in nature and thus frequently invoked for a large plethora of interesting applications. From ecology to physics, individual entities in mutual interactions are grouped in families, homogeneous in kind. These latter interact selectively, through a sequence of self-consistently regulated steps, whose deeply rooted architecture is stored in the assigned matrix of connections. The asymptotic equilibrium eventually attained by the system, and its associated stability, can be assessed by employing standard nonlinear dynamics tools. For many practical applications, it is however important to externally drive the system towards a desired equilibrium, which is resilient, hence stable, to external perturbations. To this end we here consider a system made up of N interacting populations which evolve according to general rate equations, bearing attributes of universality. One species is added to the pool of interacting families and used as a dynamical controller to induce novel stable equilibria. Use can be made of the root locus method to shape the needed control, in terms of intrinsic reactivity and adopted protocol of injection. The proposed method is tested on both synthetic and real data, thus enabling to demonstrate its robustness and versatility. PMID:28892493
Indexación multidimensional configurable
Directory of Open Access Journals (Sweden)
José L. Zechinelli M.
2004-01-01
Full Text Available Existe una gran cantidad de métodos de indexado para datos multidimensionales. La idea fundamental de éstos es generar estructuras dinámicas para organizar objetos complejos, de tal manera que se puedan consultar de forma rápida y efectiva. Aunque existen taxonomías que definen las propiedades de cada método de indexado. A un usuario no experto le es difícil decidir cuál método podría ser apropiado para un conjunto particular de datos. En este artículo describimos la arquitectura de un framework el cual ofrece herramientas de análisis e implementación de diversos métodos de indexado multidimensional y que ayuda a un usuario a determinar el método más adecuado, para un conjunto de datos. Además se analizan ciertas propiedades de los mismos y el tipo de consultas que se llevarán a cabo en ellos.
Phase space eigenfunctions of multidimensional quadratic Hamiltonians
International Nuclear Information System (INIS)
Dodonov, V.V.; Man'ko, V.I.
1986-01-01
We obtain the explicit expressions for phace space eigenfunctions (PSE),i.e. Weyl's symbols of dyadic operators like vertical stroken> ,vertical strokem>, being the solution of the Schroedinger equation with the Hamiltonian which is a quite arbitrary multidimensional quadratic form of the operators of Cartesian coordinates and conjugated to them momenta with time-dependent coefficients. It is shown that for an arbitrary quadratic Hamiltonian one can always construct the set of completely factorized PSE which are products of N factors, each factor being dependent only on two arguments for nnot=m and on a single argument for n=m. These arguments are nothing but constants of motion of the correspondent classical system. PSE are expressed in terms of the associated Laguerre polynomials in the case of a discrete spectrum and in terms of the Airy functions in the continuous spectrum case. Three examples are considered: a harmonic oscillator with a time-dependent frequency, a charged particle in a nonstationary uniform magnetic field, and a particle in a time-dependent uniform potential field. (orig.)
Experimental verification of multidimensional quantum steering
Li, Che-Ming; Lo, Hsin-Pin; Chen, Liang-Yu; Yabushita, Atsushi
2018-03-01
Quantum steering enables one party to communicate with another remote party even if the sender is untrusted. Such characteristics of quantum systems not only provide direct applications to quantum information science, but are also conceptually important for distinguishing between quantum and classical resources. While concrete illustrations of steering have been shown in several experiments, quantum steering has not been certified for higher dimensional systems. Here, we introduce a simple method to experimentally certify two different kinds of quantum steering: Einstein-Podolsky-Rosen (EPR) steering and single-system (SS) steering (i.e., temporal steering), for dimensionality (d) up to d = 16. The former reveals the steerability among bipartite systems, whereas the latter manifests itself in single quantum objects. We use multidimensional steering witnesses to verify EPR steering of polarization-entangled pairs and SS steering of single photons. The ratios between the measured witnesses and the maximum values achieved by classical mimicries are observed to increase with d for both EPR and SS steering. The designed scenario offers a new method to study further the genuine multipartite steering of large dimensionality and potential uses in quantum information processing.
Analysis of Multidimensional Poverty: Theory and Case Studies ...
International Development Research Centre (IDRC) Digital Library (Canada)
2009-08-18
Aug 18, 2009 ... ... of applying a factorial technique, Multiple Correspondence Analysis, to poverty analysis. ... Analysis of Multidimensional Poverty: Theory and Case Studies ... agreement to support joint research projects in December 2017.
Van der Zee, KI; Van Oudenhoven, JP
2000-01-01
In today's global business environment, executive work is becoming more international in orientation. Several skills and traits may underlie executive success in an inter national environment. The Multicultural Personality Questionnaire was developed as a multidimensional instrument aimed at
Capturing Complex Multidimensional Data in Location-Based Data Warehouses
DEFF Research Database (Denmark)
Timko, Igor; Pedersen, Torben Bach
2004-01-01
Motivated by the increasing need to handle complex multidimensional data inlocation-based data warehouses, this paper proposes apowerful data model that is able to capture the complexities of such data. The model provides a foundation for handling complex transportationinfrastructures...
Benefits of Multidimensional Measures of Child Well Being in China.
Gatenio Gabel, Shirley; Zhang, Yiwei
2017-11-06
In recent decades, measures of child well-being have evolved from single dimension to multidimensional measures. Multi-dimensional measures deepen and broaden our understanding of child well-being and inform us of areas of neglect. Child well-being in China today is measured through proxy measures of household need. This paper discusses the evolution of child well-being measures more generally, explores the benefits of positive indicators and multiple dimensions in formulating policy, and then reviews efforts to date by the Chinese government, researchers, and non-governmental and intergovernmental organizations to develop comprehensive multidimensional measures of child well-being in China. The domains and their potential interactions, as well as data sources and availability, are presented. The authors believe that child well-being in China would benefit from the development of a multidimensional index and that there is sufficient data to develop such an index.
A multidimensional subdiffusion model: An arbitrage-free market
International Nuclear Information System (INIS)
Li Guo-Hua; Zhang Hong; Luo Mao-Kang
2012-01-01
To capture the subdiffusive characteristics of financial markets, the subordinated process, directed by the inverse α-stale subordinator S α (t) for 0 < α < 1, has been employed as the model of asset prices. In this article, we introduce a multidimensional subdiffusion model that has a bond and K correlated stocks. The stock price process is a multidimensional subdiffusion process directed by the inverse α-stable subordinator. This model describes the period of stagnation for each stock and the behavior of the dependency between multiple stocks. Moreover, we derive the multidimensional fractional backward Kolmogorov equation for the subordinated process using the Laplace transform technique. Finally, using a martingale approach, we prove that the multidimensional subdiffusion model is arbitrage-free, and also gives an arbitrage-free pricing rule for contingent claims associated with the martingale measure. (interdisciplinary physics and related areas of science and technology)
Heuristics for Solving Problem of Evacuating Non-Ambulatory People in a Short-Notice Disaster
2012-12-01
Problem B&B Branch and Bound B&C Branch and Cut BPP Bin Packing Problem CCRP Capacity Constrained Route Planner CO Combinatorial Optimzation CRED...increase. Worst-case analyses for the related Bin Packing Problem ( BPP ), which can be viewed as a CVRP where all the customers are at the same
Packing and Cohesive Properties of Some Locally Extracted Starches
African Journals Online (AJOL)
... properties of the particles affect the packing and cohesive properties of the starches, and are important in predicting the behaviour of the starches during handling and use in pharmaceutical preparations. These properties need to be closely controlled in pre-formulation studies. Keywords: Packing and cohesive properties, ...
Characterization of metallic surfaces in phosphorous-bronze ordered packings
International Nuclear Information System (INIS)
Sandru, Claudia; Titescu, Gh.
1997-01-01
Copper and its alloys, particularly the phosphorous bronze, are characterized by a high water wettability as compared with other materials. This feature led to utilization of phosphorous bronze in fabrication of contact elements, a packing type equipping the distillation columns. For heavy water separation by isotopic distillation under vacuum, ordered packings of phosphorous bronze networks were fabricated. The superior performances of these packings are determined by the material and also by the geometrical form and the state of the metallic surface. Thus, a procedure of evaluating the wettability has been developed, based on tests of the network material. The results of the tests constitute a criterion of rating the functional performances of packings, particularly of their efficiencies. Also, investigation techniques of the chemical composition and of the thickness of superficial layer on the packing were developed. It was found that the packing surface presents a layer of about 5-20 μm formed mainly by oxides of copper, tin, and, depending on the packing treatment, of oxides of other elements coming from the treatment agent. The paper presents characterization of phosphorous bronze treated with potassium permanganate, a specific treatment for improving the functional performances of the packings used in the heavy water concentration and re-concentration installations
Duration of Nasal Packs in the Management of Epistaxis
International Nuclear Information System (INIS)
Kundi, N. A.; Raza, M.
2015-01-01
Objective:To compare the efficacy of nasal packs for 12 and 24 hours in the management of epistaxis. Study Design: Quasi experimental study. Place and Duration of Study: Combined Military Hospital, Nowshera and Heavy Industries Taxilla Hospital, from October 2012 to April 2013. Methodology: A total of 60 patients presenting with epistaxis were selected and were divided into two groups of 30 patients each. Patients in both the groups were managed by nasal packs. In group-A packs were removed after 12 hours while in group-B after 24 hours. Symptoms of headache, lacrimation and recurrence of bleeding were recorded. SPSS 20 was used for data analysis and p-value less than 0.01 was considered significant. Results: There was significant difference for headache between removal of nasal packs after 12 hours and 24 hours (p < 0.001). There was significant difference for excessive lacrimation at 12 and 24 hours (p = 0.001). No significant difference was observed for recurrence of bleed when nasal packs were removed at 12 and 24 hours (p = 0.317). Conclusion: Duration in removal of nasal packs after 12 or 24 hours made a difference in the management of epistaxis. Symptoms of headache and excessive lacrimation were significantly higher when nasal packs were removed after 24 hours. It is recommended that patient could be managed with lesser duration of packs after episode of epistaxis to avoid inconvenience. (author)
Hydrodynamics of multi-phase packed bed micro-reactors
Márquez Luzardo, N.M.
2010-01-01
Why to use packed bed micro-reactors for catalyst testing? Miniaturized packed bed reactors have a large surface-to-volume ratio at the reactor and particle level that favors the heat- and mass-transfer processes at all scales (intra-particle, inter-phase and inter-particle or reactor level). If the
The Performance of Structured Packings in Trickle-Bed Reactors
Frank, M.J.W.; Kuipers, J.A.M.; Versteeg, G.F.; Swaaij, W.P.M. van
1999-01-01
An experimental study was carried out to investigate whether the use of structured packings might improve the mass transfer characteristics and the catalyst effectiveness of a trickle-bed reactor. Therefore, the performances of a structured packing, consisting of KATAPAK elements, and a dumped
demonstrating close-packing of atoms using spherical bubble gums
African Journals Online (AJOL)
Admin
chemistry and junior inorganic chemistry courses. However, the subject of three dimen- sional close-packing of atoms has always been difficult for students to understand. In particular, students find it difficult to visualize the packing of atoms in different layers. They cannot clearly identify tetrahedral and octahedral holes, and.
Improved Erythrocyte Osmotic Fragility and Packed Cell Volume ...
African Journals Online (AJOL)
Improved Erythrocyte Osmotic Fragility and Packed Cell Volume following administration of Aloe barbadensis Juice Extract in Rats. ... Abstract. Aloe barbadensis is a popular house plant that has a long history of a multipurpose folk remedy. ... Keywords: osmotic fragility, packed cell volume, haemoglobin, Aloe vera ...
Metallic witness packs for behind-armour debris characterization
Verolme, J.L.; Szymczak, M.; Broos, J.P.F.
1999-01-01
For the experimental characterization of behind-armour debris so-called metallic witness packs can be used. A metallic witness pack consists of an array of metallic plates interspaced by polystyrene foam sheets. To quantify the fragment mass and velocity from the corresponding hole area and position
27 CFR 24.255 - Bottling or packing wine.
2010-04-01
... in the same tax class when that wine is removed from bond, without benefit of tolerance, when the... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Bottling or packing wine..., DEPARTMENT OF THE TREASURY LIQUORS WINE Storage, Treatment and Finishing of Wine Bottling, Packing, and...
Characteristics of illegal and legal cigarette packs sold in Guatemala.
Arevalo, Rodrigo; Corral, Juan E; Monzon, Diego; Yoon, Mira; Barnoya, Joaquin
2016-11-25
Guatemala, as a party to the Framework Convention on Tobacco Control (FCTC), is required to regulate cigarette packaging and labeling and eliminate illicit tobacco trade. Current packaging and labeling characteristics (of legal and illegal cigarettes) and their compliance with the FCTC is unknown. We sought to analyze package and label characteristics of illegal and legal cigarettes sold in Guatemala. We visited the 22 largest traditional markets in the country to purchase illegal cigarettes. All brands registered on tobacco industry websites were purchased as legal cigarettes. Analysis compared labeling characteristics of illegal and legal packs. Most (95%) markets and street vendors sold illegal cigarettes; 104 packs were purchased (79 illegal and 25 legal). Ten percent of illegal and none of the legal packs had misleading terms. Half of the illegal packs had a warning label covering 26 to 50% of the pack surface. All legal packs had a label covering 25% of the surface. Illegal packs were more likely to have information on constituents and emissions (85% vs. 45%, p Guatemala, neither illegal nor legal cigarette packs comply with FCTC labeling mandates. Urgent implementation and enforcement of the FCTC is necessary to halt the tobacco epidemic.
On new physics searches with multidimensional differential shapes
Ferreira, Felipe; Fichet, Sylvain; Sanz, Veronica
2018-03-01
In the context of upcoming new physics searches at the LHC, we investigate the impact of multidimensional differential rates in typical LHC analyses. We discuss the properties of shape information, and argue that multidimensional rates bring limited information in the scope of a discovery, but can have a large impact on model discrimination. We also point out subtleties about systematic uncertainties cancellations and the Cauchy-Schwarz bound on interference terms.
An Analysis of Multi-dimensional Gender Inequality in Pakistan
Abdul Hamid; Aisha M. Ahmed
2011-01-01
Women make almost half of the population of Pakistan. They also contribute significantly to economic and social growth. However, in developing countries like Pakistan, women usually suffer from multidimensional inequality of opportunities leading to multidimensional poverty. The dimensions of family, women identity, health, education and women access to economic resources and employment contribute significantly to the discrimination of women. The provision of more opportunities to women in th...
On multidimensional item response theory -- a coordinate free approach
Antal, Tamás
2007-01-01
A coordinate system free definition of complex structure multidimensional item response theory (MIRT) for dichotomously scored items is presented. The point of view taken emphasizes the possibilities and subtleties of understanding MIRT as a multidimensional extension of the ``classical'' unidimensional item response theory models. The main theorem of the paper is that every monotonic MIRT model looks the same; they are all trivial extensions of univariate item response theory.
Background elimination methods for multidimensional coincidence γ-ray spectra
International Nuclear Information System (INIS)
Morhac, M.
1997-01-01
In the paper new methods to separate useful information from background in one, two, three and multidimensional spectra (histograms) measured in large multidetector γ-ray arrays are derived. The sensitive nonlinear peak clipping algorithm is the basis of the methods for estimation of the background in multidimensional spectra. The derived procedures are simple and therefore have a very low cost in terms of computing time. (orig.)
Modelling of multidimensional quantum systems by the numerical functional integration
International Nuclear Information System (INIS)
Lobanov, Yu.Yu.; Zhidkov, E.P.
1990-01-01
The employment of the numerical functional integration for the description of multidimensional systems in quantum and statistical physics is considered. For the multiple functional integrals with respect to Gaussian measures in the full separable metric spaces the new approximation formulas exact on a class of polynomial functionals of a given summary degree are constructed. The use of the formulas is demonstrated on example of computation of the Green function and the ground state energy in multidimensional Calogero model. 15 refs.; 2 tabs
Dimensionless groups for multidimensional heat and mass transfer in adsorbed natural gas storage
Energy Technology Data Exchange (ETDEWEB)
Sphaier, L.A. [Universidade Federal Fluminense (UFF), Niteroi, RJ (Brazil). Programa de Pos-Graduacao em Engenharia Mecanica. Lab. de Mecanica Teorica e Aplicada], E-mail: lasphaier@mec.uff.br
2010-07-01
This paper provides a new methodology for analyzing heat and mass transfer in gas storage via adsorption. The foundation behind the proposed methodology comprises a set of physically meaningful dimensionless groups. A discussion regarding the development of such groups is herein presented, providing a fully normalized multidimensional formulation for describing the transport mechanisms involved in adsorbed gas storage. After such presentation, data from previous literature studies associated with the problem of adsorbed natural gas storage are employed for determining realistic values for the developed parameters. Then, a one-dimensional test-case problem is selected for illustrating the application of the dimensionless formulation for simulating the operation of adsorbed gas reservoirs. The test problem is focused on analyzing an adsorbed gas discharge operation. This problem is numerically solved, and the solution is verified against previously published literature data. The presented results demonstrate how a higher heat of sorption values lead to reduced discharge capacities. (author)
A nodal collocation approximation for the multi-dimensional PL equations - 2D applications
International Nuclear Information System (INIS)
Capilla, M.; Talavera, C.F.; Ginestar, D.; Verdu, G.
2008-01-01
A classical approach to solve the neutron transport equation is to apply the spherical harmonics method obtaining a finite approximation known as the P L equations. In this work, the derivation of the P L equations for multi-dimensional geometries is reviewed and a nodal collocation method is developed to discretize these equations on a rectangular mesh based on the expansion of the neutronic fluxes in terms of orthogonal Legendre polynomials. The performance of the method and the dominant transport Lambda Modes are obtained for a homogeneous 2D problem, a heterogeneous 2D anisotropic scattering problem, a heterogeneous 2D problem and a benchmark problem corresponding to a MOX fuel reactor core
Multilayer DNA Origami Packed on Hexagonal and Hybrid Lattices
DEFF Research Database (Denmark)
Ke, Yonggang; Voigt, Niels Vinther; Shih, William M.
2012-01-01
“Scaffolded DNA origami” has been proven to be a powerful and efficient approach to construct two-dimensional or three-dimensional objects with great complexity. Multilayer DNA origami has been demonstrated with helices packing along either honeycomb-lattice geometry or square-lattice geometry....... Here we report successful folding of multilayer DNA origami with helices arranged on a close-packed hexagonal lattice. This arrangement yields a higher density of helical packing and therefore higher resolution of spatial addressing than has been shown previously. We also demonstrate hybrid multilayer...... DNA origami with honeycomb-lattice, square-lattice, and hexagonal-lattice packing of helices all in one design. The availability of hexagonal close-packing of helices extends our ability to build complex structures using DNA nanotechnology....
Multilayer DNA origami packed on hexagonal and hybrid lattices.
Ke, Yonggang; Voigt, Niels V; Gothelf, Kurt V; Shih, William M
2012-01-25
"Scaffolded DNA origami" has been proven to be a powerful and efficient approach to construct two-dimensional or three-dimensional objects with great complexity. Multilayer DNA origami has been demonstrated with helices packing along either honeycomb-lattice geometry or square-lattice geometry. Here we report successful folding of multilayer DNA origami with helices arranged on a close-packed hexagonal lattice. This arrangement yields a higher density of helical packing and therefore higher resolution of spatial addressing than has been shown previously. We also demonstrate hybrid multilayer DNA origami with honeycomb-lattice, square-lattice, and hexagonal-lattice packing of helices all in one design. The availability of hexagonal close-packing of helices extends our ability to build complex structures using DNA nanotechnology. © 2011 American Chemical Society
Random close packing of hard spheres and disks
International Nuclear Information System (INIS)
Berryman, J.G.
1983-01-01
A simple definition of random close packing of hard spheres is presented, and the consequences of this definition are explored. According to this definition, random close packing occurs at the minimum packing fraction eta for which the median nearest-neighbor radius equals the diameter of the spheres. Using the radial distribution function at more dilute concentrations to estimate median nearest-neighbor radii, lower bounds on the critical packing fraction eta/sub RCP/ are obtained and the value of eta/sub RCP/ is estimated by extrapolation. Random close packing is predicted to occur for eta/sub RCP/ = 0.64 +- 0.02 in three dimensions and eta/sub RCP/ = 0.82 +- 0.02 in two dimensions. Both of these predictions are shown to be consistent with the available experimental data
Statistical theory of correlations in random packings of hard particles.
Jin, Yuliang; Puckett, James G; Makse, Hernán A
2014-05-01
A random packing of hard particles represents a fundamental model for granular matter. Despite its importance, analytical modeling of random packings remains difficult due to the existence of strong correlations which preclude the development of a simple theory. Here, we take inspiration from liquid theories for the n-particle angular correlation function to develop a formalism of random packings of hard particles from the bottom up. A progressive expansion into a shell of particles converges in the large layer limit under a Kirkwood-like approximation of higher-order correlations. We apply the formalism to hard disks and predict the density of two-dimensional random close packing (RCP), ϕ(rcp) = 0.85 ± 0.01, and random loose packing (RLP), ϕ(rlp) = 0.67 ± 0.01. Our theory also predicts a phase diagram and angular correlation functions that are in good agreement with experimental and numerical data.
Fatigue and multidimensional disease severity in chronic obstructive pulmonary disease
Directory of Open Access Journals (Sweden)
Inal-Ince Deniz
2010-06-01
Full Text Available Abstract Background and aims Fatigue is associated with longitudinal ratings of health in patients with chronic obstructive pulmonary disease (COPD. Although the degree of airflow obstruction is often used to grade disease severity in patients with COPD, multidimensional grading systems have recently been developed. The aim of this study was to investigate the relationship between perceived and actual fatigue level and multidimensional disease severity in patients with COPD. Materials and methods Twenty-two patients with COPD (aged 52-74 years took part in the study. Multidimensional disease severity was measured using the SAFE and BODE indices. Perceived fatigue was assessed using the Fatigue Severity Scale (FSS and the Fatigue Impact Scale (FIS. Peripheral muscle endurance was evaluated using the number of sit-ups, squats, and modified push-ups that each patient could do. Results Thirteen patients (59% had severe fatigue, and their St George's Respiratory Questionnaire scores were significantly higher (p Conclusions Peripheral muscle endurance and fatigue perception in patients with COPD was related to multidimensional disease severity measured with both the SAFE and BODE indices. Improvements in perceived and actual fatigue levels may positively affect multidimensional disease severity and health status in COPD patients. Further research is needed to investigate the effects of fatigue perception and exercise training on patients with different stages of multidimensional COPD severity.
6-PACK programme to decrease fall injuries in acute hospitals: cluster randomised controlled trial.
Barker, Anna L; Morello, Renata T; Wolfe, Rory; Brand, Caroline A; Haines, Terry P; Hill, Keith D; Brauer, Sandra G; Botti, Mari; Cumming, Robert G; Livingston, Patricia M; Sherrington, Catherine; Zavarsek, Silva; Lindley, Richard I; Kamar, Jeannette
2016-01-26
To evaluate the effect of the 6-PACK programme on falls and fall injuries in acute wards. Cluster randomised controlled trial. Six Australian hospitals. All patients admitted to 24 acute wards during the trial period. Participating wards were randomly assigned to receive either the nurse led 6-PACK programme or usual care over 12 months. The 6-PACK programme included a fall risk tool and individualised use of one or more of six interventions: "falls alert" sign, supervision of patients in the bathroom, ensuring patients' walking aids are within reach, a toileting regimen, use of a low-low bed, and use of a bed/chair alarm. The co-primary outcomes were falls and fall injuries per 1000 occupied bed days. During the trial, 46 245 admissions to 16 medical and eight surgical wards occurred. As many people were admitted more than once, this represented 31 411 individual patients. Patients' characteristics and length of stay were similar for intervention and control wards. Use of 6-PACK programme components was higher on intervention wards than on control wards (incidence rate ratio 3.05, 95% confidence interval 2.14 to 4.34; Pcontrol wards. Positive changes in falls prevention practice occurred following the introduction of the 6-PACK programme. However, no difference was seen in falls or fall injuries between groups. High quality evidence showing the effectiveness of falls prevention interventions in acute wards remains absent. Novel solutions to the problem of in-hospital falls are urgently needed. Australian New Zealand Clinical Trials Registry ACTRN12611000332921. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.
Influence of γ-ray radiation on mechanical character of packing
International Nuclear Information System (INIS)
Tashiro, Hisao; Sakuma, Toshio
1989-01-01
This paper describes the results of investigation on coefficient of friction, normal to axial pressure-ratio and compressed strain of packings influenced by γ-ray irradiation, which are necessary to evaluate the mechanical characteristics of packing, using packings made of seven kinds of new materials and conventional asbestos packing A. It resulted that graphite packing was less influenced by the γ-ray exposure, whereas carbon-fiber (pitch) packing, tefron-fiber packing and alamid-fiber packing were much influenced as compared with the graphite packing. (author)
SEPTOPLASTY WITH AND WITHOUT NASAL PACKING: A COMPARATIVE STUDY
Directory of Open Access Journals (Sweden)
Mitta
2016-05-01
Full Text Available Septoplasty is one of the most commonly performed surgeries in rhinology to relieve nasal obstruction of patients with distortion in the midline cartilage or septum of the nose to relieve nasal obstruction of patient and findings consistent with nasal endoscopy. The anterior nasal packing routinely done following septoplasty is usually conventional and not evidence based. The purpose of nasal packing is to obtain haemostasis, enhance opposition of septal flaps, avoid septal haematoma formation, close the dead space, avoid synechiae formation, provide support to septal cartilage and prevent its displacement. OBJECTIVE This study intends to evaluate the effects of nasal packing on surgical success and related complications in septoplasty. MATERIALS AND METHODS The present clinical prospective and randomised study was carried out on patients attending Otorhinolaryngology Department of Santhiram Medical College & General Hospital between March 2012 and March 2015. Patients undergoing septoplasty were randomised either to receive anterior nasal packing or to not receive nasal packing postoperatively. RESULTS Levels of pain experienced by patients with nasal packing postoperatively during the initial 24 hours postoperatively and during the removal of the pack were significantly more. Post-operative headache, epiphora, swallowing discomfort and sleep disturbance were more in patients with nasal packing and statistically (p.05. Septal haematoma, adhesions and local infections in both groups were statistically insignificant (p>.05. CONCLUSION Septoplasty enhances the standard of living of patients with septal deviation and nasal obstruction. Our study results suggest that nasal packing after septoplasty is not obligatory. Nasal packing causes considerably more pain and complications, and it should be reserved only for those who have bleeding predisposition.
Wild immunology assessed by multidimensional mass cytometry.
Japp, Alberto Sada; Hoffmann, Kerstin; Schlickeiser, Stephan; Glauben, Rainer; Nikolaou, Christos; Maecker, Holden T; Braun, Julian; Matzmohr, Nadine; Sawitzki, Birgit; Siegmund, Britta; Radbruch, Andreas; Volk, Hans-Dieter; Frentsch, Marco; Kunkel, Desiree; Thiel, Andreas
2017-01-01
A great part of our knowledge on mammalian immunology has been established in laboratory settings. The use of inbred mouse strains enabled controlled studies of immune cell and molecule functions in defined settings. These studies were usually performed in specific-pathogen free (SPF) environments providing standardized conditions. In contrast, mammalians including humans living in their natural habitat are continuously facing pathogen encounters throughout their life. The influences of environmental conditions on the signatures of the immune system and on experimental outcomes are yet not well defined. Thus, the transferability of results obtained in current experimental systems to the physiological human situation has always been a matter of debate. Studies elucidating the diversity of "wild immunology" imprintings in detail and comparing it with those of "clean" lab mice are sparse. Here, we applied multidimensional mass cytometry to dissect phenotypic and functional differences between distinct groups of laboratory and pet shop mice as a source for "wild mice". For this purpose, we developed a 31-antibody panel for murine leukocyte subsets identification and a 35-antibody panel assessing various cytokines. Established murine leukocyte populations were easily identified and diverse immune signatures indicative of numerous pathogen encounters were classified particularly in pet shop mice and to a lesser extent in quarantine and non-SPF mice as compared to SPF mice. In addition, unsupervised analysis identified distinct clusters that associated strongly with the degree of pathogenic priming, including increased frequencies of activated NK cells and antigen-experienced B- and T-cell subsets. Our study unravels the complexity of immune signatures altered under physiological pathogen challenges and highlights the importance of carefully adapting laboratory settings for immunological studies in mice, including drug and therapy testing. © 2016 International Society
Multidimensional analysis: B-tagging at LEP
International Nuclear Information System (INIS)
de la Vaissiere, C.; Palma-Lopes, S.
1989-01-01
At the Z 0 , the cross-section for e + e - → b anti b is large (6.5 nb), as is the fraction of hadronic events leading to b anti b (22%). A jet topology allows to distinguish naturally the products of the b and anti b fragmentation and decays. The Z 0 looks therefore an attractive place to pursue B physics. Techniques previously used at PEP and PETRA to tag the b-flavor, have provided reasonable b-purities, at the cost of poor efficiencies. A first technique originally proposed to measure the b-lifetime was to use leptonic decays, but the corresponding branching ratios are at the 10% level. At Z 0 energies, P. Roudeau shows that a 91% purity and 6% efficiency can be obtained. The TASSO collaboration was the first to use a vertex detector for b-enrichment. They achieved a b-purity of about 68%, with a 16%-efficiency. The best way to increase these low yields is to improve the resolution of vertex detectors on impact parameters. DELPHI will be equipped with a silicon microstrip vertex detector which will provide an asymptotic accuracy of 20 μm on impact parameters in the plane transverse to the beam, to be compared with the 150 μm quoted by TASSO. However this 20 μm, combined with limited coverage, can not disentangle the multiple decays occurring in a b anti b event. In this intermediate situation multidimensional analysis may provide tagging of b anti b events with high purity and good efficiency. 11 refs., 2 figs., 2 tabs
PERSPECTIVA MULTIDIMENSIONAL DO TRABALHO NA CONTEMPORANEIDADE
Directory of Open Access Journals (Sweden)
Lilian Carminatti
2015-12-01
Full Text Available O objetivo deste estudo é analisar a evolução do tema trabalho e novas formas de flexibilização das relações laborais que proporcionam identidade, significado e bem-estar. O trabalho, como uma atividade prazerosa, passa por uma mudança de postura das pessoas frente à atividade ocupacional, a partir do autoconhecimento, planejamento de carreira e de uma jornada de trabalho que vislumbre a melhora na qualidade de vida. A promoção do bem-estar presume a articulação entre as relações de trabalho atravessadas pelo sistema capitalista e a importância de equilibrar necessidades individuais e a competitividade organizacional. Como elementos balizadores surgem: a relação com os significados do trabalho, o planejamento de carreira e pós-carreira e a conexão entre valores pessoais e organizacionais. Adotou-se para a pesquisa uma estratégia metodológica qualitativa que se propõe a investigar a partir da exploração e descrição as dimensões do tema trabalho na sociedade contemporânea. Dessa forma, a promoção do bem-estar e o planejamento de carreira devem ser tratados como planejamento de vida durante todo o período funcional, a partir de uma visão multidimensional do colaborador inserida em um amplo contexto cultural e social que ultrapassa o ambiente organizacional.
Timing and related artifacts in multidimensional NMR
International Nuclear Information System (INIS)
Marion, Dominique
2012-01-01
The information content of multidimensional NMR spectra is limited by the presence of several kinds of artifacts that originate from incorrect timing of evolution periods. The objective of this review is to provide tools for successful implementation of published pulse sequences, in which timing and pulse compensations are often implicit. We will analyze the constraints set by the use of Fourier transformation, the spin precession during rectangular or shaped pulses, the Bloch-Siegert effects due to pulse on other spins and the delay introduced by the filters for the acquisition dimension. A frequency dependent phase correction or an incorrect scaling of the first data point leads to baseline offsets or curvature due to the properties of the Fourier transform. Because any r.f. pulse has a finite length, chemical shift is always active during excitation, flip-back, inversion, and refocusing pulses. Rectangular or selective shaped pulses can be split into three periods: an ideal rotation surrounded by two chemical shift evolution periods, which should be subtracted from the adjacent delays to avoid linear phase correction. Bloch-Siegert effects originate from irradiation at frequencies near those observed in the spectrum and can lead to phase or frequency shifts. They can be minimized by simultaneous irradiation on both sides of the observed spins. In terms of timing, the very end of the pulse sequence the acquisition behaves differently since the data are filtered by either analog or digital means. This additional delay is filter and spectrometer specific and should be tuned to minimize the required phase correction. Combined together, all these adjustments lead to perfectly phased spectra with flat baseline and no peak shifts or distortion. (author)
MINIMUM ENTROPY DECONVOLUTION OF ONE-AND MULTI-DIMENSIONAL NON-GAUSSIAN LINEAR RANDOM PROCESSES
Institute of Scientific and Technical Information of China (English)
程乾生
1990-01-01
The minimum entropy deconvolution is considered as one of the methods for decomposing non-Gaussian linear processes. The concept of peakedness of a system response sequence is presented and its properties are studied. With the aid of the peakedness, the convergence theory of the minimum entropy deconvolution is established. The problem of the minimum entropy deconvolution of multi-dimensional non-Gaussian linear random processes is first investigated and the corresponding theory is given. In addition, the relation between the minimum entropy deconvolution and parameter method is discussed.
Directory of Open Access Journals (Sweden)
Peixin Zhao
2013-01-01
Full Text Available Community detection in social networks plays an important role in cluster analysis. Many traditional techniques for one-dimensional problems have been proven inadequate for high-dimensional or mixed type datasets due to the data sparseness and attribute redundancy. In this paper we propose a graph-based clustering method for multidimensional datasets. This novel method has two distinguished features: nonbinary hierarchical tree and the multi-membership clusters. The nonbinary hierarchical tree clearly highlights meaningful clusters, while the multimembership feature may provide more useful service strategies. Experimental results on the customer relationship management confirm the effectiveness of the new method.
Data planning and analysis for synthesis of multidimensional laws (nonlinear multifactor analysis)
International Nuclear Information System (INIS)
Mordashev, V. M.
2010-01-01
The methodology of data planning and analysis for synthesis of multidimensional laws using visualization is described along with the ensuing method of numerical data approximation by functions with “separable” variables. The method is developed for the cases of source data presented as (a) a table where all cells are filled, (b) an orthogonal table where quite certain cells are filled, and (c) a table where, generally speaking, arbitrary cells are not filled. The method was successfully applied for different problems of nuclear science and technology.
Investigation of multi-dimensional computational models for calculating pollutant transport
International Nuclear Information System (INIS)
Pepper, D.W.; Cooper, R.E.; Baker, A.J.
1980-01-01
A performance study of five numerical solution algorithms for multi-dimensional advection-diffusion prediction on mesoscale grids was made. Test problems include transport of point and distributed sources, and a simulation of a continuous source. In all cases, analytical solutions are available to assess relative accuracy. The particle-in-cell and second-moment algorithms, both of which employ sub-grid resolution coupled with Lagrangian advection, exhibit superior accuracy in modeling a point source release. For modeling of a distributed source, algorithms based upon the pseudospectral and finite element interpolation concepts, exhibit improved accuracy on practical discretizations
Research and application of packing density for pebble bed in HTR
International Nuclear Information System (INIS)
Yu Fujiang; Xie Fei; Sun Ximing
2015-01-01
The pebble bed high temperature gas-cooled reactor is one of the major types of reactors developed by Chinese nuclear technology. The statistical analysis for packing density in the pebble bed is an important issue of physical-thermal calculation and safety analysis. Aimed to this problem, a new kind of method was set up to solve this problem. Compared with the traditional lattice-fill method and the experiment, its efficiency and accuracy were verified, while helping to find out the best length of unit in the traditional lattice-fill method. This method was used to analyze the boundary effects observed by experiments. (authors)
A fresh look at the wolf-pack theory of companion-animal dog social behavior.
van Kerkhove, Wendy
2004-01-01
A popular perspective on the social behavior of dogs in multiple-dog households sees the dogs' behavior as reflecting the sociobiological laws of the rigidly structured dominance hierarchy that has been described for wolf packs. This view suggests that aggression problems among dogs are natural expressions of conflict that arise whenever dominance status is in contention. One recommended solution has been for the owner to endorse and enforce a particular dominance hierarchy because, on the wolf pack model, aggression is minimized when the structure of the hierarchy is clear, strong, and stable. This article questions the validity of this perspective on 2 principal grounds. First, because it does not seem to occur in the wild, this article suggests the strong dominance hierarchy that has been described for wolves may be a by-product of captivity. If true, it implies that social behavior--even in wolves--may be a product more of environmental circumstances and contingencies than an instinctive directive. Second, because feral dogs do not exhibit the classic wolf-pack structure, the validity of the canid, social dominance hierarchy again comes into question. This article suggests that behavioral learning theory offers another perspective regarding the behavior of dogs and wolves in the wild or in captivity and offers an effective intervention for aggression problems.
An efficient multi-dimensional implementation of VSIAM3 and its applications to free surface flows
Yokoi, Kensuke; Furuichi, Mikito; Sakai, Mikio
2017-12-01
We propose an efficient multidimensional implementation of VSIAM3 (volume/surface integrated average-based multi-moment method). Although VSIAM3 is a highly capable fluid solver based on a multi-moment concept and has been used for a wide variety of fluid problems, VSIAM3 could not simulate some simple benchmark problems well (for instance, lid-driven cavity flows) due to relatively high numerical viscosity. In this paper, we resolve the issue by using the efficient multidimensional approach. The proposed VSIAM3 is shown to capture lid-driven cavity flows of the Reynolds number up to Re = 7500 with a Cartesian grid of 128 × 128, which was not capable for the original VSIAM3. We also tested the proposed framework in free surface flow problems (droplet collision and separation of We = 40 and droplet splashing on a superhydrophobic substrate). The numerical results by the proposed VSIAM3 showed reasonable agreements with these experiments. The proposed VSIAM3 could capture droplet collision and separation of We = 40 with a low numerical resolution (8 meshes for the initial diameter of droplets). We also simulated free surface flows including particles toward non-Newtonian flow applications. These numerical results have showed that the proposed VSIAM3 can robustly simulate interactions among air, particles (solid), and liquid.
Do gray wolves (Canis lupus) support pack mates during aggressive inter-pack interactions?
Cassidy, Kira A; McIntyre, Richard T
2016-09-01
For group-living mammals, social coordination increases success in everything from hunting and foraging (Crofoot and Wrangham in Mind the Gap, Springer, Berlin, 2010; Bailey et al. in Behav Ecol Sociobiol 67:1-17, 2013) to agonism (Mosser and Packer in Anim Behav 78:359-370, 2009; Wilson et al. in Anim Behav 83:277-291, 2012; Cassidy et al. in Behav Ecol 26:1352-1360, 2015). Cooperation is found in many species and, due to its low costs, likely is a determining factor in the evolution of living in social groups (Smith in Anim Behav 92:291-304, 2014). Beyond cooperation, many mammals perform costly behaviors for the benefit of group mates (e.g., parental care, food sharing, grooming). Altruism is considered the most extreme case of cooperation where the altruist increases the fitness of the recipient while decreasing its own fitness (Bell in Selection: the mechanism of evolution. Oxford University Press, Oxford 2008). Gray wolf life history requires intra-pack familiarity, communication, and cooperation in order to succeed in hunting (MacNulty et al. in Behav Ecol doi: 10.1093/beheco/arr159 2011) and protecting group resources (Stahler et al. in J Anim Ecol 82: 222-234, 2013; Cassidy et al. in Behav Ecol 26:1352-1360, 2015). Here, we report 121 territorial aggressive inter-pack interactions in Yellowstone National Park between 1 April 1995 and 1 April 2011 (>5300 days of observation) and examine each interaction where one wolf interferes when its pack mate is being attacked by a rival group. This behavior was recorded six times (17.6 % of interactions involving an attack) and often occurred between dyads of closely related individuals. We discuss this behavior as it relates to the evolution of cooperation, sociality, and altruism.
Packing Nonspherical Particles: All Shapes Are Not Created Equal
Torquato, Salvatore
2012-02-01
Over the past decade there has been increasing interest in the effects of particle shape on the characteristics of dense particle packings, since deviations from sphericity can lead to more realistic models of granular media, nanostructured materials, and tissue architecture. It is clear the that the broken rotational symmetry of a nonspherical particle is a crucial aspect in determining its resulting packing characteristics, but given the infinite variety of possible shapes (ellipsoids, superballs, regular and irregular polyhedra, etc.) it is desirable to formulate packing organizing principles based the particle shape. Such principles are beginning to be elucidated; see Refs. 1 and 2 and references therein. Depending upon whether the particle has central symmetry, inequivalent principle axes, and smooth or flat surfaces, we can describe the nature of its densest packing (which is typically periodic) as well as its disordered jammed states (which may or may not be isostatic). Changing the shape of a particle can dramatically alter its packing attributes. This tunability capability via particle shape could be used to tailor many-particle systems (e.g., colloids and granular media) to have designed crystal, liquid and glassy states. [4pt] [1] S. Torquato and F. H. Stillinger, ``Jammed Hard-Particle Packings: From Kepler to Bernal and Beyond," Rev. Modern Phys. 82, 2633 (2010). [0pt] [2] Y. Jiao and S. Torquato, Communication: ``A Packing of Truncated Tetrahedra That Nearly Fills All of Space and its Melting Properties," J. Chem. Phys. 135, 151101 (2011).
Fast charge implications: Pack and cell analysis and comparison
Tanim, Tanvir R.; Shirk, Matthew G.; Bewley, Randy L.; Dufek, Eric J.; Liaw, Bor Yann
2018-03-01
This study investigates the effect of 50-kW (about 2C) direct current fast charging on a full-size battery electric vehicle's battery pack in comparison to a pack exclusively charged at 3.3 kW, which is the common alternating current Level 2 charging power level. Comparable scaled charging protocols are also independently applied to individual cells at three different temperatures, 20 °C, 30 °C, and 40 °C, to perform a comparative analysis with the packs. Dominant cell-level aging modes were identified through incremental capacity analysis and compared with full packs to gain a clear understanding of additional key factors that affect pack aging. While the cell-level study showed a minor impact on performance due to direct current fast charging, the packs showed a significantly higher rate of capacity fade under similar charging protocols. This indicates that pack-level aging cannot be directly extrapolated from cell evaluation. Delayed fast charging, completing shortly before discharge, was found to have less of an impact on battery degradation than conventional alternating current Level 2 charging.
Avoidance of cigarette pack health warnings among regular cigarette smokers.
Maynard, Olivia M; Attwood, Angela; O'Brien, Laura; Brooks, Sabrina; Hedge, Craig; Leonards, Ute; Munafò, Marcus R
2014-03-01
Previous research with adults and adolescents indicates that plain cigarette packs increase visual attention to health warnings among non-smokers and non-regular smokers, but not among regular smokers. This may be because regular smokers: (1) are familiar with the health warnings, (2) preferentially attend to branding, or (3) actively avoid health warnings. We sought to distinguish between these explanations using eye-tracking technology. A convenience sample of 30 adult dependent smokers participated in an eye-tracking study. Participants viewed branded, plain and blank packs of cigarettes with familiar and unfamiliar health warnings. The number of fixations to health warnings and branding on the different pack types were recorded. Analysis of variance indicated that regular smokers were biased towards fixating the branding rather than the health warning on all three pack types. This bias was smaller, but still evident, for blank packs, where smokers preferentially attended the blank region over the health warnings. Time-course analysis showed that for branded and plain packs, attention was preferentially directed to the branding location for the entire 10s of the stimulus presentation, while for blank packs this occurred for the last 8s of the stimulus presentation. Familiarity with health warnings had no effect on eye gaze location. Smokers actively avoid cigarette pack health warnings, and this remains the case even in the absence of salient branding information. Smokers may have learned to divert their attention away from cigarette pack health warnings. These findings have implications for cigarette packaging and health warning policy. Copyright © 2014 The Authors. Published by Elsevier Ireland Ltd.. All rights reserved.
Enabling Microliquid Chromatography by Microbead Packing of Microchannels
Balvin, Manuel; Zheng, Yun
2014-01-01
The microbead packing is the critical element required in the success of on-chip microfabrication of critical microfluidic components for in-situ analysis and detection of chiral amino acids. In order for microliquid chromatography to occur, there must be a stationary phase medium within the microchannel that interacts with the analytes present within flowing fluid. The stationary phase media are the microbeads packed by the process discussed in this work. The purpose of the microliquid chromatography is to provide a lightweight, low-volume, and low-power element to separate amino acids and their chiral partners efficiently to understand better the origin of life. In order to densely pack microbeads into the microchannels, a liquid slurry of microbeads was created. Microbeads were extracted from a commercially available high-performance liquid chromatography column. The silica beads extracted were 5 microns in diameter, and had surface coating of phenyl-hexyl. These microbeads were mixed with a 200- proof ethanol solution to create a microbead slurry with the right viscosity for packing. A microfilter is placed at the outlet via of the microchannel and the slurry is injected, then withdrawn across a filter using modified syringes. After each injection, the channel is flushed with ethanol to enhance packing. This cycle is repeated numerous times to allow for a tightly packed channel of microbeads. Typical microbead packing occurs in the macroscale into tubes or channels by using highly pressurized systems. Moreover, these channels are typically long and straight without any turns or curves. On the other hand, this method of microbead packing is completed within a microchannel 75 micrometers in diameter. Moreover, the microbead packing is completed into a serpentine type microchannel, such that it maximizes microchannel length within a microchip. Doing so enhances the interactions of the analytes with the microbeads to separate efficiently amino acids and amino acid
Scottish young people's perceptions of standardised packs - a qualitative study
Directory of Open Access Journals (Sweden)
Andy Macgregor
2018-03-01
Full Text Available Background Standardised cigarette packs were introduced into the UK in May 2016. Retailers could sell old stock until May 2017 after which only the sale of cigarettes and tobacco in standardised packs was allowed. As in Australia, pack shape, colour, opening mechanism and font are regulated, together with the size and position of health warnings and number of cigarettes in a pack. This paper explores Scottish young people's awareness of and views about standardised packs in Spring 2017. Methods The DISPLAY study is a five year study established to evaluate the national tobacco point-of sale (POS promotions ban in four communities in Scotland. This paper is based on the qualitative component, annual focus groups carried out with Secondary 2 (13 year olds and Secondary 4 (15 year olds students in four secondary schools. 16 groups (82 students convened in February - March 2017 explored students' perceptions of standardised packaging. Results There was a high level of awareness of standardised packs prior to their full implementation. Smokers had bought them, and they and other participants had seen them in possession of friends and family members, and in litter. Participants' views of the new packaging were generally negative, described as unappealing and depressing, particularly the pictorial health warnings. Packs were compared unfavourably with previous non-standardised versions. However, there was no consensus on their likely impact. Some participants argued that their impact would be widespread, while others thought that any impact would be confined to young non/occasional smokers and that established smokers would be unaffected. Conclusions In early 2017 young people in Scotland had high awareness and knowledge of standardised tobacco packs before their full implementation. Despite differing views about their likely impact on youth smoking, participants irrespective of smoking status overwhelmingly regarded them as unattractive and less
The Cauchy problem for the Pavlov equation
International Nuclear Information System (INIS)
Grinevich, P G; Santini, P M; Wu, D
2015-01-01
Commutation of multidimensional vector fields leads to integrable nonlinear dispersionless PDEs that arise in various problems of mathematical physics and have been intensively studied in recent literature. This report aims to solve the scattering and inverse scattering problem for integrable dispersionless PDEs, recently introduced just at a formal level, concentrating on the prototypical example of the Pavlov equation, and to justify an existence theorem for global bounded solutions of the associated Cauchy problem with small data. (paper)
Ecology of southern ocean pack ice.
Brierley, Andrew S; Thomas, David N
2002-01-01
Around Antarctica the annual five-fold growth and decay of sea ice is the most prominent physical process and has a profound impact on marine life there. In winter the pack ice canopy extends to cover almost 20 million square kilometres--some 8% of the southern hemisphere and an area larger than the Antarctic continent itself (13.2 million square kilometres)--and is one of the largest, most dynamic ecosystems on earth. Biological activity is associated with all physical components of the sea-ice system: the sea-ice surface; the internal sea-ice matrix and brine channel system; the underside of sea ice and the waters in the vicinity of sea ice that are modified by the presence of sea ice. Microbial and microalgal communities proliferate on and within sea ice and are grazed by a wide range of proto- and macrozooplankton that inhabit the sea ice in large concentrations. Grazing organisms also exploit biogenic material released from the sea ice at ice break-up or melt. Although rates of primary production in the underlying water column are often low because of shading by sea-ice cover, sea ice itself forms a substratum that provides standing stocks of bacteria, algae and grazers significantly higher than those in ice-free areas. Decay of sea ice in summer releases particulate and dissolved organic matter to the water column, playing a major role in biogeochemical cycling as well as seeding water column phytoplankton blooms. Numerous zooplankton species graze sea-ice algae, benefiting additionally because the overlying sea-ice ceiling provides a refuge from surface predators. Sea ice is an important nursery habitat for Antarctic krill, the pivotal species in the Southern Ocean marine ecosystem. Some deep-water fish migrate to shallow depths beneath sea ice to exploit the elevated concentrations of some zooplankton there. The increased secondary production associated with pack ice and the sea-ice edge is exploited by many higher predators, with seals, seabirds and whales
Ultratight crystal packing of a 10 kDa protein
Energy Technology Data Exchange (ETDEWEB)
Trillo-Muyo, Sergio [Molecular Biology Institute of Barcelona, Spanish Research Council CSIC, Barcelona Science Park, c/Baldiri Reixac 15-21, 08028 Barcelona (Spain); Jasilionis, Andrius [Vilnius University, M. K. Čiurlionio 21/27, 03101 Vilnius (Lithuania); Domagalski, Marcin J. [University of Virginia, 1340 Jefferson Park Avenue, Charlottesville, VA 22908-0736 (United States); Chruszcz, Maksymilian [University of South Carolina, 631 Sumter Street, Columbia, SC 29208 (United States); Minor, Wladek [University of Virginia, 1340 Jefferson Park Avenue, Charlottesville, VA 22908-0736 (United States); Kuisiene, Nomeda [Vilnius University, M. K. Čiurlionio 21/27, 03101 Vilnius (Lithuania); Arolas, Joan L.; Solà, Maria; Gomis-Rüth, F. Xavier, E-mail: xgrcri@ibmb.csic.es [Molecular Biology Institute of Barcelona, Spanish Research Council CSIC, Barcelona Science Park, c/Baldiri Reixac 15-21, 08028 Barcelona (Spain)
2013-03-01
The crystal structure of the C-terminal domain of a putative U32 peptidase from G. thermoleovorans is reported; it is one of the most tightly packed protein structures reported to date. While small organic molecules generally crystallize forming tightly packed lattices with little solvent content, proteins form air-sensitive high-solvent-content crystals. Here, the crystallization and full structure analysis of a novel recombinant 10 kDa protein corresponding to the C-terminal domain of a putative U32 peptidase are reported. The orthorhombic crystal contained only 24.5% solvent and is therefore among the most tightly packed protein lattices ever reported.
International Nuclear Information System (INIS)
El-Nabulsi, Ahmad Rami
2009-01-01
Multidimensional fractional actionlike variational problem with time-dependent dynamical fractional exponents is constructed. Fractional Euler-Lagrange equations are derived and discussed in some details. The results obtained are used to explore some novel aspects of fractional quantum field theory where many interesting consequences are revealed, in particular the complexification of quantum field theory, in particular Dirac operators and the novel notion of 'mass without mass'.
Multidimensional scaling for large genomic data sets
Directory of Open Access Journals (Sweden)
Lu Henry
2008-04-01
Full Text Available Abstract Background Multi-dimensional scaling (MDS is aimed to represent high dimensional data in a low dimensional space with preservation of the similarities between data points. This reduction in dimensionality is crucial for analyzing and revealing the genuine structure hidden in the data. For noisy data, dimension reduction can effectively reduce the effect of noise on the embedded structure. For large data set, dimension reduction can effectively reduce information retrieval complexity. Thus, MDS techniques are used in many applications of data mining and gene network research. However, although there have been a number of studies that applied MDS techniques to genomics research, the number of analyzed data points was restricted by the high computational complexity of MDS. In general, a non-metric MDS method is faster than a metric MDS, but it does not preserve the true relationships. The computational complexity of most metric MDS methods is over O(N2, so that it is difficult to process a data set of a large number of genes N, such as in the case of whole genome microarray data. Results We developed a new rapid metric MDS method with a low computational complexity, making metric MDS applicable for large data sets. Computer simulation showed that the new method of split-and-combine MDS (SC-MDS is fast, accurate and efficient. Our empirical studies using microarray data on the yeast cell cycle showed that the performance of K-means in the reduced dimensional space is similar to or slightly better than that of K-means in the original space, but about three times faster to obtain the clustering results. Our clustering results using SC-MDS are more stable than those in the original space. Hence, the proposed SC-MDS is useful for analyzing whole genome data. Conclusion Our new method reduces the computational complexity from O(N3 to O(N when the dimension of the feature space is far less than the number of genes N, and it successfully
Bodin, Jacques
2015-03-01
In this study, new multi-dimensional time-domain random walk (TDRW) algorithms are derived from approximate one-dimensional (1-D), two-dimensional (2-D), and three-dimensional (3-D) analytical solutions of the advection-dispersion equation and from exact 1-D, 2-D, and 3-D analytical solutions of the pure-diffusion equation. These algorithms enable the calculation of both the time required for a particle to travel a specified distance in a homogeneous medium and the mass recovery at the observation point, which may be incomplete due to 2-D or 3-D transverse dispersion or diffusion. The method is extended to heterogeneous media, represented as a piecewise collection of homogeneous media. The particle motion is then decomposed along a series of intermediate checkpoints located on the medium interface boundaries. The accuracy of the multi-dimensional TDRW method is verified against (i) exact analytical solutions of solute transport in homogeneous media and (ii) finite-difference simulations in a synthetic 2-D heterogeneous medium of simple geometry. The results demonstrate that the method is ideally suited to purely diffusive transport and to advection-dispersion transport problems dominated by advection. Conversely, the method is not recommended for highly dispersive transport problems because the accuracy of the advection-dispersion TDRW algorithms degrades rapidly for a low Péclet number, consistent with the accuracy limit of the approximate analytical solutions. The proposed approach provides a unified methodology for deriving multi-dimensional time-domain particle equations and may be applicable to other mathematical transport models, provided that appropriate analytical solutions are available.
Energy Technology Data Exchange (ETDEWEB)
Ouchi, Tatsuya.; Harada, Tsutomu.; Ando, Hideki.; Yamato, Tsugio
1998-12-01
Formed joint packing materials presently used in each place of continuous casting factories are manufactured from a main material of refractory powder and various subsidiary materials, added with binder, mixed and formed to products. This joint material has disadvantages of 1) Setting to flange part of long nozzle is difficult owing to inferior ordinary temperature shape retaining property (workability), and 2) Hot workable time (workability) is short, when used under hot condition. To solve these problems, sealing property and workability (ordinary temperature shape retaining property and hot workable time) of joint packing material were improved using new binder and Al system materials, and hard type formed jpint packing material of excellent hot sealing property and workability compared to conventional formed packing materials was obtained. Examining various resins and refractory powders, special emulsion type resin and a material which consisted of a main refractory material of alumina and subsidiary materials of clay, flint, Al system metals were finally selected. The measurement results on ordinary temperature shape retaining property, hot workable time and hot sealing property of this joint packing material showed excellent results. (NEDO)
Packing Density Approach for Sustainable Development of Concrete
Directory of Open Access Journals (Sweden)
Sudarshan Dattatraya KORE
2017-12-01
Full Text Available This paper deals with the details of optimized mix design for normal strength concrete using particle packing density method. Also the concrete mixes were designed as per BIS: 10262-2009. Different water-cement ratios were used and kept same in both design methods. An attempt has been made to obtain sustainable and cost effective concrete product by use of particle packing density method. The parameters such as workability, compressive strength, cost analysis and carbon di oxide emission were discussed. The results of the study showed that, the compressive strength of the concrete produced by packing density method are closer to that of design compressive strength of BIS code method. By adopting the packing density method for design of concrete mixes, resulted in 11% cost saving with 12% reduction in carbon di oxide emission.
PNGS-A unit 4 composite graphite valve packing program
International Nuclear Information System (INIS)
Meaney, F.
1992-01-01
During the outage of Pickering 4 for retubing and rehabilitation, a composite graphite packing program was completed on 100 conventional valves and 50 nuclear valves. This paper describes component refurbishment, related maintenance, and manpower requirements. 2 figs
The investigation of cooling tower packing in various arrangements
International Nuclear Information System (INIS)
Golshayshi, H.R.; Missenden, J.F.
1998-01-01
The effect of form with corrugated packing on heat transfer and pressure drop characteristics in atmospheric cooling towers has been studied experimentally. The results showed that the heat transfer coefficient decreased with increase in packing pitch and increase in the ratio of rib pitch to rib height. Friction factors were expressed by a dimensional equation which included pitch and distance between the packings, for both smooth and rough surface. From these results, the relationship between packing heat transfer coefficient and pressure drop was deduced. The correlations were verified with additional experimental data taken with 1.1,P/D p /e 5 . This provides a useful semi experimental relation, in the area generally lacking in design and performance data. (author)
Radiation sterilization of plastic packing materials and aseptic packaging
International Nuclear Information System (INIS)
Tokuoka, Keiko
1986-01-01
In the present day of 'satiation', quality, not quantity, is emphasized for foods, the consumers being oriented toward raw and healthy foodstuff. Aseptic Packaging is excellent means of conservation. While conventionally chemicals have been used for sterilization of packing materials for aseptic packaging, the sterilization by radiation is used in part recently. The following are described : history of aseptic packaging and its features, sterilization by radiation, γ-ray sterilization of large-sized containers, the development of an aseptic packaging system using electron rays, the occurrence of offensive odors from packing materials (comparison of odors from various materials, volatile substances occurring in irradiated polyethylene, influence of film grade upon the formation of carboxylic acid, influence of the irradiation conditions upon the occurrences of volatile substances, volatile substances occurring in the irradiation of bag-in-box packing materials), changes in properties of the packing materials. (Mori, K.)
A new multidimensional model with text dimensions: definition and implementation
Directory of Open Access Journals (Sweden)
MariaJ. Martin-Bautista
2013-02-01
Full Text Available We present a new multidimensional model with textual dimensions based on a knowledge structure extracted from the texts, where any textual attribute in a database can be processed, and not only XML texts. This dimension allows to treat the textual data in the same way as the non-textual one in an automatic way, without user's intervention, so all the classical operations in the multidimensional model can been defined for this textual dimension. While most of the models dealing with texts that can be found in the literature are not implemented, in this proposal, the multidimensional model and the OLAP system have been implemented in a software tool, so it can be tested on real data. A case study with medical data is included in this work.
Multidimensional poverty: an alternative measurement approach for the United States?
Waglé, Udaya R
2008-06-01
International poverty research has increasingly underscored the need to use multidimensional approaches to measure poverty. Largely embraced in Europe and elsewhere, this has not had much impact on the way poverty is measured in the United States. In this paper, I use a comprehensive multidimensional framework including economic well-being, capability, and social inclusion to examine poverty in the US. Data from the 2004 General Social Survey support the interconnectedness among these poverty dimensions, indicating that the multidimensional framework utilizing a comprehensive set of information provides a compelling value added to poverty measurement. The suggested demographic characteristics of the various categories of the poor are somewhat similar between this approach and other traditional approaches. But the more comprehensive and accurate measurement outcomes from this approach help policymakers target resources at the specific groups.
Multidimensional Scaling Localization Algorithm in Wireless Sensor Networks
Directory of Open Access Journals (Sweden)
Zhang Dongyang
2014-02-01
Full Text Available Due to the localization algorithm in large-scale wireless sensor network exists shortcomings both in positioning accuracy and time complexity compared to traditional localization algorithm, this paper presents a fast multidimensional scaling location algorithm. By positioning algorithm for fast multidimensional scaling, fast mapping initialization, fast mapping and coordinate transform can get schematic coordinates of node, coordinates Initialize of MDS algorithm, an accurate estimate of the node coordinates and using the PRORUSTES to analysis alignment of the coordinate and final position coordinates of nodes etc. There are four steps, and the thesis gives specific implementation steps of the algorithm. Finally, compared with stochastic algorithms and classical MDS algorithm experiment, the thesis takes application of specific examples. Experimental results show that: the proposed localization algorithm has fast multidimensional scaling positioning accuracy in ensuring certain circumstances, but also greatly improves the speed of operation.
Quantum and Multidimensional Explanations in a Neurobiological Context of Mind.
Korf, Jakob
2015-08-01
This article examines the possible relevance of physical-mathematical multidimensional or quantum concepts aiming at understanding the (human) mind in a neurobiological context. Some typical features of the quantum and multidimensional concepts are briefly introduced, including entanglement, superposition, holonomic, and quantum field theories. Next, we consider neurobiological principles, such as the brain and its emerging (physical) mind, evolutionary and ontological origins, entropy, syntropy/neg-entropy, causation, and brain energy metabolism. In many biological processes, including biochemical conversions, protein folding, and sensory perception, the ubiquitous involvement of quantum mechanisms is well recognized. Quantum and multidimensional approaches might be expected to help describe and model both brain and mental processes, but an understanding of their direct involvement in mental activity, that is, without mediation by molecular processes, remains elusive. More work has to be done to bridge the gap between current neurobiological and physical-mathematical concepts with their associated quantum-mind theories. © The Author(s) 2014.
Conservative Initial Mapping For Multidimensional Simulations of Stellar Explosions
International Nuclear Information System (INIS)
Chen, Ke-Jung; Heger, Alexander; Almgren, Ann
2012-01-01
Mapping one-dimensional stellar profiles onto multidimensional grids as initial conditions for hydrodynamics calculations can lead to numerical artifacts, one of the most severe of which is the violation of conservation laws for physical quantities such as energy and mass. Here we introduce a numerical scheme for mapping one-dimensional spherically-symmetric data onto multidimensional meshes so that these physical quantities are conserved. We validate our scheme by porting a realistic 1D Lagrangian stellar profile to the new multidimensional Eulerian hydro code CASTRO. Our results show that all important features in the profiles are reproduced on the new grid and that conservation laws are enforced at all resolutions after mapping.
A set packing inspired method for real-time junction train routing
DEFF Research Database (Denmark)
Lusby, Richard Martin; Larsen, Jesper; Ehrgott, Matthias
2013-01-01
Efficiently coordinating the often large number of interdependent, timetabled train movements on a railway junction, while satisfying a number of operational requirements, is one of the most important problems faced by a railway company. The most critical variant of the problem arises on a daily...... basis at major railway junctions where disruptions to rail traffic make the planned schedule/routing infeasible and rolling stock planners are forced to re-schedule/re-route trains in order to recover feasibility. The dynamic nature of the problem means that good solutions must be obtained quickly....... In this paper we describe a set packing inspired formulation of this problem and develop a branch-and-price based solution approach. A real life test instance arising in Germany and supplied by the major German railway company, Deutsche Bahn, indicates the efficiency of the proposed approach by confirming...
A Set Packing Inspired Method for Real-Time Junction Train Routing
DEFF Research Database (Denmark)
Lusby, Richard Martin; Larsen, Jesper; Ehrgott, Matthias
Efficiently coordinating the often large number of interdependent, timetabled train movements on a railway junction, while satisfying a number of operational requirements, is one of the most important problems faced by a railway company. The most critical variant of the problem arises on a daily...... basis at major railway junctions where disruptions to rail traffi c make the planned schedule/routing infeasible and rolling stock planners are forced to reschedule/re-route trains in order to recover feasibility. The dynamic nature of the problem means that good solutions must be obtained quickly....... In this paper we describe a set packing inspired formulation of this problem and develop a branch-and-price based solution approach. A real life test instance arising in Germany and supplied by the major German railway company, Deutsche Bahn, indicates the efficiency of the proposed approach by confirming...
Utilizing Multidimensional Measures of Race in Education Research: The Case of Teacher Perceptions.
Irizarry, Yasmiyn
2015-10-01
Education scholarship on race using quantitative data analysis consists largely of studies on the black-white dichotomy, and more recently, on the experiences of student within conventional racial/ethnic categories (white, Hispanic/Latina/o, Asian, black). Despite substantial shifts in the racial and ethnic composition of American children, studies continue to overlook the diverse racialized experiences for students of Asian and Latina/o descent, the racialization of immigration status, and the educational experiences of Native American students. This study provides one possible strategy for developing multidimensional measures of race using large-scale datasets and demonstrates the utility of multidimensional measures for examining educational inequality, using teacher perceptions of student behavior as a case in point. With data from the first grade wave of the Early Childhood Longitudinal Study, Kindergarten Cohort of 1998-1999, I examine differences in teacher ratings of Externalizing Problem Behaviors and Approaches to Learning across fourteen racialized subgroups at the intersections of race, ethnicity, and immigrant status. Results show substantial subgroup variation in teacher perceptions of problem and learning behaviors, while also highlighting key points of divergence and convergence within conventional racial/ethnic categories.
Granular flow through an aperture: Influence of the packing fraction
Aguirre, M. A.; De Schant, R.; Géminard, J.-C.
2014-07-01
For the last 50 years, the flow of a granular material through an aperture has been intensely studied in gravity-driven vertical systems (e.g., silos and hoppers). Nevertheless, in many industrial applications, grains are horizontally transported at constant velocity, lying on conveyor belts or floating on the surface of flowing liquids. Unlike fluid flows, that are controlled by the pressure, granular flow is not sensitive to the local pressure but rather to the local velocity of the grains at the outlet. We can also expect the flow rate to depend on the local density of the grains. Indeed, vertical systems are packed in dense configurations by gravity, but, in contrast, in horizontal systems the density can take a large range of values, potentially very small, which may significantly alter the flow rate. In the present article, we study, for different initial packing fractions, the discharge through an orifice of monodisperse grains driven at constant velocity by a horizontal conveyor belt. We report how, during the discharge, the packing fraction is modified by the presence of the outlet, and we analyze how changes in the packing fraction induce variations in the flow rate. We observe that variations of packing fraction do not affect the velocity of the grains at the outlet, and, therefore, we establish that flow-rate variations are directly related to changes in the packing fraction.
Progress in multidimensional neutron transport computation
International Nuclear Information System (INIS)
Lewis, E.E.
1977-01-01
The methods available for solution of the time-independent neutron transport problems arising in the analysis of nuclear systems are examined. The merits of deterministic and Monte Carlo methods are briefly compared. The capabilities of deterministic computational methods derived from the first-order form of the transport equation, from the second-order even-parity form of this equation, and from integral transport formulations are discussed in some detail. Emphasis is placed on the approaches for dealing with the related problems of computer memory requirements, computational cost, and achievable accuracy. Attention is directed to some areas where problems exist currently and where the need for further work appears to be particularly warranted
Energy Technology Data Exchange (ETDEWEB)
Magalhaes, Joao Vicente Martins de; Leal, Rafael Amorim Ferreira; Martins, Andre Leibsohn; Calderon, Agostinho; Ferreira, Marcus Vinicius Duarte [Petrobras S.A., Rio de Janeiro, RJ (Brazil)], E-mails: ivmm@petrobras.com.br, rafaelleal@petrobras.com.br, aleibsohn@petrobras.com.br, agoscal@petrobras.com.br, mvdferreira@petrobras.com.br; Simoes, Bruno; Barbosa, Diego [Halliburton, Novo Cavaleiros, Macae, RJ (Brazil)], E-mails: bruno.simoes@halliburton.com.br, diego.barbosa@halliburton.com.br
2010-07-01
In the petroleum exploitation and production in deep water, at the fields operated by PETROBRAS, Brazil, one of the problems frequently found is the need of elimination of sand production, having in mind that the most of those fields produce from the non consolidated sandstones. The opened well Gravel Packing is the technique most used for that task. Due to the fact of Gravel Packing operations occurs at thousand of meters below the surface, it is necessary the computational simulation for forecasting how particle deposition (Gravel) in the well occurs. So, it was used the commercial pack of fluid dynamics FLUENT 12, which calculates the fluid velocity field, coupled to another commercial pack, the EDEM, based on discrete elements that treat of particle mechanics. The coupling of the two software has shown adequate the comparison of the computational results with the experimental data shows a good adjustment. Besides, it was possible to simulate problems of well early clogging, showing that the computational simulation is strong and capable of captivating such a phenomena.
SM4MQ: A Semantic Model for Multidimensional Queries
DEFF Research Database (Denmark)
Varga, Jovan; Dobrokhotova, Ekaterina; Romero, Oscar
2017-01-01
On-Line Analytical Processing (OLAP) is a data analysis approach to support decision-making. On top of that, Exploratory OLAP is a novel initiative for the convergence of OLAP and the Semantic Web (SW) that enables the use of OLAP techniques on SW data. Moreover, OLAP approaches exploit different......, sharing, and reuse on the SW. As OLAP is based on the underlying multidimensional (MD) data model we denote such queries as MD queries and define SM4MQ: A Semantic Model for Multidimensional Queries. Furthermore, we propose a method to automate the exploitation of queries by means of SPARQL. We apply...
Multidimensional quantum entanglement with large-scale integrated optics
DEFF Research Database (Denmark)
Wang, Jianwei; Paesani, Stefano; Ding, Yunhong
2018-01-01
-dimensional entanglement. A programmable bipartite entangled system is realized with dimension up to 15 × 15 on a large-scale silicon-photonics quantum circuit. The device integrates more than 550 photonic components on a single chip, including 16 identical photon-pair sources. We verify the high precision, generality......The ability to control multidimensional quantum systems is key for the investigation of fundamental science and for the development of advanced quantum technologies. We demonstrate a multidimensional integrated quantum photonic platform able to generate, control and analyze high...
Multi-Dimensional Customer Data Analysis in Online Auctions
Institute of Scientific and Technical Information of China (English)
LAO Guoling; XIONG Kuan; QIN Zheng
2007-01-01
In this paper, we designed a customer-centered data warehouse system with five subjects: listing, bidding, transaction,accounts, and customer contact based on the business process of online auction companies. For each subject, we analyzed its fact indexes and dimensions. Then take transaction subject as example,analyzed the data warehouse model in detail, and got the multi-dimensional analysis structure of transaction subject. At last, using data mining to do customer segmentation, we divided customers into four types: impulse customer, prudent customer, potential customer, and ordinary customer. By the result of multi-dimensional customer data analysis, online auction companies can do more target marketing and increase customer loyalty.
Energy Technology Data Exchange (ETDEWEB)
Kotoh, K. [Faculty of Engineering, Kyushu University, Nishi-ku, Fukuoka (Japan); Graduate School of Engineering, Kyushu University, Nishi-ku, Fukuoka (Japan); Kubo, K.; Takashima, S.; Moriyama, S.T. [Graduate School of Engineering, Kyushu University, Nishi-ku, Fukuoka (Japan); Tanaka, M. [National Institute for Fusion Science, Oroshi-cho, Toki, Gifu (Japan); Sugiyama, T. [Faculty of Engineering, Nagoya University, Furo-cho, Chikusa-ku, Nagoya (Japan)
2015-03-15
Authors have been developing a cryogenic pressure swing adsorption system for hydrogen isotope separation. In the problem of its design and operation, it is necessary to predict the concentration profiles developing in packed beds of adsorbent pellets. The profiling is affected by the longitudinal dispersion of gas flowing in packed beds, in addition to the mass transfer resistance in porous media of adsorbent pellets. In this work, an equation is derived for estimating the packed-bed dispersion coefficient of hydrogen isotopes, by analyzing the breakthrough curves of trace D{sub 2} or HD replacing H{sub 2} adsorbed in synthetic zeolite particles packed columns at the liquefied nitrogen temperature 77.4 K. Since specialized for hydrogen isotopes, this equation can be considered to estimate the dispersion coefficients more reliable for the cryogenic hydrogen isotope adsorption process, than the existing equations. (authors)
Multidimensional computer simulation of Stirling cycle engines
Hall, Charles A.; Porsching, Thomas A.
1992-01-01
This report summarizes the activities performed under NASA-Grant NAG3-1097 during 1991. During that period, work centered on the following tasks: (1) to investigate more effective solvers for ALGAE; (2) to modify the plotting package for ALGAE; and (3) to validate ALGAE by simulating oscillating flow problems similar to those studied by Kurzweg and Ibrahim.
Energy Technology Data Exchange (ETDEWEB)
Lee, Seung Jun; Park, Ik Kyu; Yoon, Han Young [Thermal-Hydraulic Safety Research Division, Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Jae, Byoung [School of Mechanical Engineering, Chungnam National University, Daejeon (Korea, Republic of)
2017-01-15
Two-fluid equations are widely used to obtain averaged behaviors of two-phase flows. This study addresses a problem that may arise when the two-fluid equations are used for multi-dimensional bubbly flows. If steady drag is the only accounted force for the interfacial momentum transfer, the disperse-phase velocity would be the same as the continuous-phase velocity when the flow is fully developed without gravity. However, existing momentum equations may show unphysical results in estimating the relative velocity of the disperse phase against the continuous-phase. First, we examine two types of existing momentum equations. One is the standard two-fluid momentum equation in which the disperse-phase is treated as a continuum. The other is the averaged momentum equation derived from a solid/ fluid particle motion. We show that the existing equations are not proper for multi-dimensional bubbly flows. To resolve the problem mentioned above, we modify the form of the Reynolds stress terms in the averaged momentum equation based on the solid/fluid particle motion. The proposed equation shows physically correct results for both multi-dimensional laminar and turbulent flows.
A multi-dimensional model of groupwork for adolescent girls who have been sexually abused.
Lindon, J; Nourse, C A
1994-04-01
This paper describes a treatment approach for sexually abused adolescent girls using a group work model. The model incorporates three treatment modalities: a skills component, a psychotherapeutic component, and an educative component. The group ran for 16 sessions over a 6-month period and each girl was assessed prior to joining the group. The girls were again assessed at the end of treatment and a 6-months follow-up; all of them showed improvement on self-statements (outcome) and on behavioral measures assessed by others (follow-up). Girls who had been sexually abused demonstrated difficulties in many areas of their lives following abuse. These problems related to their feelings of guilt and helplessness in relation to both themselves and their abuser. Sexually abused children often have poor knowledge of sexual matters and demonstrate confusion over their own body image. Using a multidimensional model the problems following abuse can be addressed.
Data matching for free-surface multiple attenuation by multidimensional deconvolution
van der Neut, Joost; Frijlink, Martijn; van Borselen, Roald
2012-09-01
A common strategy for surface-related multiple elimination of seismic data is to predict multiples by a convolutional model and subtract these adaptively from the input gathers. Problems can be posed by interfering multiples and primaries. Removing multiples by multidimensional deconvolution (MDD) (inversion) does not suffer from these problems. However, this approach requires data to be consistent, which is often not the case, especially not at interpolated near-offsets. A novel method is proposed to improve data consistency prior to inversion. This is done by backpropagating first-order multiples with a time-gated reference primary event and matching these with early primaries in the input gather. After data matching, multiple elimination by MDD can be applied with a deterministic inversion scheme.
Balanced sensitivity functions for tuning multi-dimensional Bayesian network classifiers
Bolt, J.H.; van der Gaag, L.C.
Multi-dimensional Bayesian network classifiers are Bayesian networks of restricted topological structure, which are tailored to classifying data instances into multiple dimensions. Like more traditional classifiers, multi-dimensional classifiers are typically learned from data and may include
Analysis of Local Dependence and Multidimensionality in Graphical Loglinear Rasch Models
DEFF Research Database (Denmark)
Kreiner, Svend; Christensen, Karl Bang
2004-01-01
Local independence; Multidimensionality; Differential item functioning; Uniform local dependence and DIF; Graphical Rasch models; Loglinear Rasch model......Local independence; Multidimensionality; Differential item functioning; Uniform local dependence and DIF; Graphical Rasch models; Loglinear Rasch model...
Energy Technology Data Exchange (ETDEWEB)
Morhac, M. [Institute of Physics, Slovak Academy of Sciences, Dubravska cesta 9, 845 11 Bratislava (Slovakia)]. E-mail: fyzimiro@savba.sk; Matousek, V. [Institute of Physics, Slovak Academy of Sciences, Dubravska cesta 9, 845 11 Bratislava (Slovakia); Turzo, I. [Institute of Physics, Slovak Academy of Sciences, Dubravska cesta 9, 845 11 Bratislava (Slovakia); Kliman, J. [Institute of Physics, Slovak Academy of Sciences, Dubravska cesta 9, 845 11 Bratislava (Slovakia)
2006-04-01
Multidimensional data acquisition, processing and visualization system to analyze experimental data in nuclear physics is described. It includes a large number of sophisticated algorithms of the multidimensional spectra processing, including background elimination, deconvolution, peak searching and fitting.
Multidimensional procurement auctions with unknown weights
DEFF Research Database (Denmark)
Greve, Thomas
This paper studies the consequences of holding a procurement auction when the principal chooses not to show its preferences. My paper extends the procurement auction model of Che (1993) to a situation where both the principal and the agents have private information. Thus, unknown parameters of bo...... gives rise to an analysis of a principal that can not fully commit to the outcome induced by the scoring rule. Therefore, my result apply to contract theory and it’s problems with imperfect commitment....
Directory of Open Access Journals (Sweden)
Ali Karbasfrushan
2014-10-01
Full Text Available Introduction: Nausea and vomiting after ear, nose and throat (ENT surgery is one of the most common and notable problems facing anesthesiologists in this area. This study was conducted to determine the effect of a pharyngeal pack on the severity of nausea, vomiting, and sore throat among patients after ear, pharynx, and throat surgeries. Materials and Methods: This randomized clinical study was performed in 140 patients (61 men and 79 women; age range, 20–40 years who had undergone nasal surgery in 2010. Patients were divided into two groups: the first group were treated using a pharyngeal pack (case group and the second group were managed without a pharyngeal pack (control group. Statistical analysis was performed using the Chi-square test and the Mann-Whitney U test. SPSS software was used for data analysis. Results: The mean severity of nausea and vomiting in the two groups was 2.057, 1.371 and 1.100, respectively, with no significant differences between groups. However, the mean severity of sore throat was 1.714 in the group with the pharyngeal pack and 1.385 in the group without pharyngeal pack (P=0.010. Conclusion: Not only does a pharyngeal pack in ENT surgery not reduce the extent and severity of nausea and vomiting, but it also increases the severity of sore throat in patients when leaving the recovery room and discharging hospital.
Packed-fluidized-bed blanket concept for a thorium-fueled commercial tokamak hybrid reactor
International Nuclear Information System (INIS)
Chi, J.W.H.; Miller, J.W.; Karbowski, J.S.; Chapin, D.L.; Kelly, J.L.
1980-09-01
A preliminary design of a thorium blanket was carried out as a part of the Commercial Tokamak Hybrid Reactor (CTHR) study. A fixed fuel blanket concept was developed as the reference CTHR blanket with uranium carbide fuel and helium coolant. A fixed fuel blanket was initially evaluated for the thorium blanket study. Subsequently, a new type of hybrid blanket, a packed-fluidized bed (PFB), was conceived. The PFB blanket concept has a number of unique features that may solve some of the problems encountered in the design of tokamak hybrid reactor blankets. This report documents the thorium blanket study and describes the feasibility assessment of the PFB blanket concept
OVERCOMING THE METER BARRIER AND THE FORMATION OF SYSTEMS WITH TIGHTLY PACKED INNER PLANETS (STIPs)
International Nuclear Information System (INIS)
Boley, A. C.; Morris, M. A.; Ford, E. B.
2014-01-01
We present a solution to the long outstanding meter barrier problem in planet formation theory. As solids spiral inward due to aerodynamic drag, they will enter disk regions that are characterized by high temperatures, densities, and pressures. High partial pressures of rock vapor can suppress solid evaporation, and promote collisions between partially molten solids, allowing rapid growth. This process should be ubiquitous in planet-forming disks, which may be evidenced by the abundant class of Systems with Tightly packed Inner Planets discovered by the NASA Kepler Mission
The Measurement of Multidimensional Gender Inequality: Continuing the Debate
Permanyer, Inaki
2010-01-01
The measurement of multidimensional gender inequality is an increasingly important topic that has very relevant policy applications and implications but which has not received much attention from the academic literature. In this paper I make a comprehensive and critical review of the indices proposed in recent years in order to systematise the…
The Structure and Validity of the Multidimensional Social Support Questionnaire
Hardesty, Patrick H.; Richardson, George B.
2012-01-01
The factor structure and concurrent validity of the Multidimensional Social Support Questionnaire, a brief measure of perceived social support for use with adolescents, was examined. Findings suggest that four dimensions of perceived social support may yield more information than assessments of the unitary construct of support. (Contains 8 tables…
Multidimensional Poverty in China: Findings Based on the CHNS
Yu, Jiantuo
2013-01-01
This paper estimates multidimensional poverty in China by applying the Alkire-Foster methodology to the China Health and Nutrition Survey 2000-2009 data. Five dimensions are included: income, living standard, education, health and social security. Results suggest that rapid economic growth has resulted not only in a reduction in income poverty but…
Integral and Multidimensional Linear Distinguishers with Correlation Zero
DEFF Research Database (Denmark)
Bogdanov, Andrey; Leander, Gregor; Nyberg, Kaisa
2012-01-01
Zero-correlation cryptanalysis uses linear approximations holding with probability exactly 1/2. In this paper, we reveal fundamental links of zero-correlation distinguishers to integral distinguishers and multidimensional linear distinguishers. We show that an integral implies zero-correlation li...... weak key assumptions. © International Association for Cryptologic Research 2012....